Graphene/Poly(aniline-co-pyrrole) Nanocomposite: Potential Candidate for Supercapacitor and Microwave Absorbing Applications.

Science.gov (United States)

Sahoo, Sumanta; Bhattacharya, Pallab; Dhibar, Saptarshi; Hatui, Goutam; Das, Tanya; Das, Chapal Kumar

2015-09-01

A simple and cost-effective in-situ chemical route to prepare the nanocomposites based on graphene and Poly(aniline-co-pyrrole) [PPP] has been proposed. Introduction of graphene changes the morphology of copolymer from spherical to fiber like. Graphene/Poly(aniline-co-pyrrole) [GPPP] nanocomposite achieved highest specific capacitance of 351 F/g and energy density of 124.8 Wh/Kg at 10 mV/s scan rate. The composite also obtained moderate specific capacitance retention of 66% after 500 cycles, which establish its potentiality as supercapacitor electrode materials. The composite also exhibited high electrical conductivity and superior microwave absorbing properties (maximum reflection loss is -29.97 dB). The absorption range corresponding to ≥ 90% absorption (or -10 dB) is 2.72 GHz which is excellent for the microwave absorbing applications.

Synthesis and characterization of Ag@polycarbazole coaxial nanocables and their enhanced dispersion behavior

Science.gov (United States)

Zahoor, Ahmad; Teng, Qiu; Wang, Haiqiao; Choudhry, M. A.; Li, Xiaoyu

2011-06-01

Ag@polycarbazole coaxial nanocables (CNCs) have been successfully fabricated by the oxidative polymerization of carbazole over Ag nanowires (NWs) in acetonitrile. The morphology of Ag NWs and CNCs was studied by employing a transmission electron microscope (TEM) and a scanning electron microscope (SEM), which showed them to be a monodisperse material. The thickness of the polymer sheath was found to be 5 nm to 8 nm by observation under a high-resolution transmission electron microscope (HR-TEM). Energy dispersive X-ray spectroscopy (EDS), FT-IR and Raman measurements were used to characterize the polymer sheath, which demonstrated it to be a carbon material in polycarbazole form. X-ray photoelectron spectroscopy (XPS) was used for an interfacial study, which revealed that Ag surface atoms remained intact during polymer growth. In the end, zeta potential showed that the dispersion stability of Ag NWs increased due to polymer encapsulation, which is significant to obtain a particular alignment for anisotropic measurement of electrical conductivity.

Preparation and influence of pH on the dynamic magnetic property of magnetic FeCoC films

Energy Technology Data Exchange (ETDEWEB)

Feng, Hongmei; Wei, Jinwu; Zhu, Zengtai; Cao, Derang; Liu, Qingfang [Key Laboratory for Magnetism and Magnetic Materials of the Ministry of Education, Lanzhou University, Lanzhou 730000 (China); Wang, Jianbo, E-mail: wangjb@lzu.edu.cn [Key Laboratory for Magnetism and Magnetic Materials of the Ministry of Education, Lanzhou University, Lanzhou 730000 (China); Key Laboratory for Special Function Materials and Structural Design of the Ministry of the Education, Lanzhou University, Lanzhou 730000 (China)

2016-07-01

FeCoC films were successfully prepared by electrochemical deposition method in different citric acid concentrations and pH values. The morphology, structure and magnetic properties were investigated. FeCoC films deposited at different citric acid concentrations have good soft magnetic performance. As the pH value increases from 2.49 to 6.02, the atomic ratio of Fe:Co range from 0.72 to 0.95. The coercivities of the films deposited at different pH values first increase and then decrease with increasing pH. The resonance frequency of the films can be tuned by controlling the pH value, and in an appropriate pH value a wide absorption peak can be obtained. - Highlights: • We have successfully prepared FeCoC soft magnetic films by electrochemical deposition method. • The resonance frequency can be controlled by changing pH value. • A widely absorption peak will be obtained when the pH value is appropriate.

Preparation and enhanced electrochemical properties of nano-sulfur/poly(pyrrole-co-aniline) cathode material for lithium/sulfur batteries

International Nuclear Information System (INIS)

Qiu Linlin; Zhang Shichao; Zhang Lan; Sun, Mingming; Wang Weikun

2010-01-01

Poly(pyrrole-co-aniline) (PPyA) copolymer nanofibers were prepared by chemical oxidation method with cetyltrimethyl ammonium chloride (CTAC) as template, and the nano-sulfur/poly(pyrrole-co-aniline) (S/PPyA) composite material in lithium batteries was achieved via co-heating the mixture of PPyA and sublimed sulfur at 160 deg. C for 24 h. The component and structure of the materials were characterized by FTIR, Raman, XRD, and SEM. PPyA with nanofiber network structure was employed as a conductive matrix, adsorbing agent and firm reaction chamber for the sulfur cathode materials. The nano-dispersed composite exhibited a specific capacity up to 1285 mAh g -1 in the initial cycle and remained 866 mAh g -1 after 40 cycles.

Synthesis, autoxidation and photooxidation of hindered pyrrole derivatives. Hindered pyrrolic nitroxide radicals; Synthese, autoxydation et photoxidation de pyrroles encombres radicaux nitroxydes pyrroliques encombres

Energy Technology Data Exchange (ETDEWEB)

Ramasseul, R [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

1969-07-01

2,5-di-t-butyl and 2,3,5-tri-t-butyl pyrrole are prepared from pinacoline and their structure is confirmed by comparison with 2,5-di-t-butyl furan and thiophene (I.R., U.V. and N.M.R. {sup 13}C satellites observation giving J{sub 13{sub C-H}} and J{sub H{sub 3}-H{sub 4}}). The sensitized photooxidation of these hindered pyrroles gives corresponding hydroperoxides which most likely structure is determined using physical and chemical methods. Oxidation of 2,5-di-t-butyl and 2,3,5-tri-t-butyl pyrrole by hydrogen peroxide in presence of inorganic per-acid of by p-nitro-perbenzoic acid does not give the pyrrolic nitroxides in contrast with secondary amines. Some N-hydroxypyrroles are then prepared from pinacoline and ethyl pivaloyl-acetate. Their oxidation by lead dioxide gives the corresponding pyrrolic nitroxides. 2,5-di-t-butyl 3,4-di-ethoxycarbonyl pyrryl 1-oxy is isolated and studied spectroscopically (visible and U.V., E.P.R.). In marked contrast with ordinary nitroxides it does not show solvent effect. It can be compared with 2,4-di-t-butyl cyclopentadienone, a carbon analog. For both, the long wave length transition does not show the usual n - {pi}* behaviour; that is confirmed by E.P.R. Using Huckel method for pyrrolic nitroxide skeleton, it is possible to have a good interpretation of experimental data. (author) [French] Les di-t-butyl 2,5 et tri-t-butyl-2,3,5 pyrrole sont synthetises a partir de la pinacoline et leur structure confirmee par comparaison avec les di-t-butyl-2,5 furanne et thiophene (I.R., U.V. et R.M.N.: observation des satellites {sup 13}C conduisant a la mesure des J{sub 13{sub C-H}} et J{sub H{sub 3}{sub -H{sub 4}}). La photoxydation sensibilisee de ces pyrroles encombres conduit aux hydroperoxydes correspondants dont la structure la plus probable est determinee par les methodes physicochimiques. L'oxydation des di-t-butyl-2,5 et tri-t-butyl-2,3,5 pyrrole par l'eau oxygenee en presence de peracide mineral ou par l'acide p

Electrochromic properties of poly (1-(phenyl)-2,5-di(2-thienyl)-1H-pyrrole-co-3,4-ethylenedioxy thiophene) and its application in electrochromic devices

Science.gov (United States)

Tarkuc, S.; Sahmetlioglu, E.; Tanyeli, C.; Akhmedov, I. M.; Toppare, L.

2008-06-01

Electrochemical copolymerization of 1-(phenyl)-2,5-di(2-thienyl)-1H-pyrrole (PTP) with 3,4-ethylenedioxy thiophene (EDOT) was carried out in acetonitrile (AN)/NaClO4/LiClO4 (0.1 M) solvent-electrolyte couple via potentiodynamic electrolysis. Characterizations of the resulting copolymer were performed via cyclic voltammetry (CV), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and spectroelectrochemical analysis. Spectroelectrochemical analyses show that the copolymer of PTP with EDOT has an electronic band gap (due to π to π∗ transition) of 1.9 eV at 480 nm, with a claret red in the fully reduced form and a blue color in the fully oxidized form. Via kinetic studies, the optical contrast (ΔT %) was found to be 8% for P(PTP-co-EDOT). Results showed that the time required to reach 95% of the ultimate transmittance was 1.7 s for the copolymer. The P(PTP-co-EDOT) film was used to construct a dual type polymer electrochromic device (ECDs) with poly(3,4-ethylenedioxy thiophene) (PEDOT). Spectroelectrochemistry, electrochromic switching and open circuit memory of the device were investigated.

Electrodeposition of polypyrrole films on aluminum surfaces from a p-toluene sulfonic acid medium

Directory of Open Access Journals (Sweden)

Andréa Santos Liu

2009-01-01

Full Text Available Electrodeposition of polypyrrole films on aluminum from aqueous solutions containing p-toluene sulfonic acid and pyrrole was performed by cyclic voltammetry and galvanostatic technique. The influence of applied current density on the morphology of the films was studied by Scanning Electron Microscopy. The films displayed a cauliflower-like structure consisting of micro-spherical grains. This structure is related to dopand intercalation in the polymeric chain. Films deposited at higher current density were more susceptible to the formation of pores and defects along the polymeric chain than films deposited at lower current density. These pores allow the penetration of aggressive species, thereby favoring the corrosion process.

Tumor Repression of VCaP Xenografts by a Pyrrole-Imidazole Polyamide

OpenAIRE

Hargrove, Amanda E.; Martinez, Thomas F.; Hare, Alissa A.; Kurmis, Alexis A.; Phillips, John W.; Sud, Sudha; Pienta, Kenneth J; Dervan, Peter B.

2015-01-01

Pyrrole-imidazole (Py-Im) polyamides are high affinity DNA-binding small molecules that can inhibit protein-DNA interactions. In VCaP cells, a human prostate cancer cell line overexpressing both AR and the TMPRSS2-ERG gene fusion, an androgen response element (ARE)-targeted Py-Im polyamide significantly downregulates AR driven gene expression. Polyamide exposure to VCaP cells reduced proliferation without causing DNA damage. Py-Im polyamide treatment also reduced tumor growth in a VCaP mouse ...

Studies of pyrrole black electrodes as possible battery positive electrodes

Energy Technology Data Exchange (ETDEWEB)

Mengoli, G.; Musiani, M.M.; Fleischmann, M.; Pletcher, D.

1984-05-01

It is shown that a polypyrrole, pyrrole black, may be formed anodically in several aqueous acids. The polypyrrole film shows a redox couple at less positive potentials than that required to form the film and the charge associated with these reduction and oxidation processes together with their stabilty to cycling varies with the anion in solution and the potential where the polypyrrole is formed; over-oxidation of the film caused by taking its potential too positive has a particularly disadvantageous affect. In the acids HBr and HI, the polypyrrole films can act as a storage medium for Br/sub 2/ or I/sub 2/ so that they may be used as a substrate for a X/sub 2//X/sup -/ electrode. Such electrodes may be charge/discharge cycled and the pyrrole/Br/sub 2/ electrode shows promise as a battery positive electrode.

Transition metal doped poly(aniline-co-pyrrole)/multi-walled carbon nanotubes nanocomposite for high performance supercapacitor electrode materials

Energy Technology Data Exchange (ETDEWEB)

Dhibar, Saptarshi; Bhattacharya, Pallab; Hatui, Goutam; Das, C.K., E-mail: chapal12@yahoo.co.in

2015-03-15

Highlights: • The CuCl{sub 2} doped copolymer (PANI and PPy)/MWCNTs nanocomposite was prepared. • The nanocomposite achieved highest specific capacitance of 383 F/g at a 0.5 A/g. • Nanocomposite exhibits better energy density as well as power density. • The nanocomposite also showed better electrical conductivity at room temperature. • The nanocomposite can be used as promising electrode materials for supercapacitor. - Abstract: In this present communication, copolymer of polyaniline (PANI) and polypyrrole (PPy) that is poly(aniline-co-pyrrole) [poly(An-co-Py)], copper chloride (CuCl{sub 2}) doped poly(aniline-co-pyrrole) [poly(An-co-Py) Cu], and CuCl{sub 2} doped poly(aniline-co-pyrrole)/multi walled carbon nanotubes (MWCNTs) [poly(An-co-Py) Cu CNT] nanocomposite have been prepared by a simple and inexpensive in-situ chemical oxidative polymerization method, using ammonium persulfate (APS) as oxidant and hydrochloric acid (HCl) as dopant and investigated as high performance supercapacitor electrode materials. The possible interaction between CuCl{sub 2} with copolymers and MWCNTs was investigated by Fourier transform infrared spectroscopy (FTIR) and UV–visible spectroscopy analysis. The morphological characteristic of all the electrode materials were analyzed by Field emission scanning electron microscopy (FESEM) and Transmission electron microscopy (TEM) study. The electrochemical characterizations of all the electrode materials were carried out by three electrode probe method where, standard calomel electrode and platinum were used as reference and counter electrodes, respectively. Among all the electrode materials, poly(An-co-Py) Cu CNT nanocomposite achieved highest specific capacitance value of 383 F/g at 0.5 A/g scan rate. The nanocomposite showed better electrical conductivity at room temperature and also attained nonlinear current–voltage characteristic. Based on the superior electrochemical as well as other properties the as prepared

Transition metal doped poly(aniline-co-pyrrole)/multi-walled carbon nanotubes nanocomposite for high performance supercapacitor electrode materials

International Nuclear Information System (INIS)

Dhibar, Saptarshi; Bhattacharya, Pallab; Hatui, Goutam; Das, C.K.

2015-01-01

Highlights: • The CuCl 2 doped copolymer (PANI and PPy)/MWCNTs nanocomposite was prepared. • The nanocomposite achieved highest specific capacitance of 383 F/g at a 0.5 A/g. • Nanocomposite exhibits better energy density as well as power density. • The nanocomposite also showed better electrical conductivity at room temperature. • The nanocomposite can be used as promising electrode materials for supercapacitor. - Abstract: In this present communication, copolymer of polyaniline (PANI) and polypyrrole (PPy) that is poly(aniline-co-pyrrole) [poly(An-co-Py)], copper chloride (CuCl 2 ) doped poly(aniline-co-pyrrole) [poly(An-co-Py) Cu], and CuCl 2 doped poly(aniline-co-pyrrole)/multi walled carbon nanotubes (MWCNTs) [poly(An-co-Py) Cu CNT] nanocomposite have been prepared by a simple and inexpensive in-situ chemical oxidative polymerization method, using ammonium persulfate (APS) as oxidant and hydrochloric acid (HCl) as dopant and investigated as high performance supercapacitor electrode materials. The possible interaction between CuCl 2 with copolymers and MWCNTs was investigated by Fourier transform infrared spectroscopy (FTIR) and UV–visible spectroscopy analysis. The morphological characteristic of all the electrode materials were analyzed by Field emission scanning electron microscopy (FESEM) and Transmission electron microscopy (TEM) study. The electrochemical characterizations of all the electrode materials were carried out by three electrode probe method where, standard calomel electrode and platinum were used as reference and counter electrodes, respectively. Among all the electrode materials, poly(An-co-Py) Cu CNT nanocomposite achieved highest specific capacitance value of 383 F/g at 0.5 A/g scan rate. The nanocomposite showed better electrical conductivity at room temperature and also attained nonlinear current–voltage characteristic. Based on the superior electrochemical as well as other properties the as prepared nanocomposite can be used

Polycondensation of pyrrole and benzaldehyde catalyzed by Maghnite–H+

Directory of Open Access Journals (Sweden)

2007-07-01

Full Text Available Rapid synthesis of poly[(pyrrole-2,5-diyl-co-(benzylidene] was achieved under microwave irradiation via the condensation of pyrrole and benzaldehyde in 1,2-dichloroethane using acid exchanged montmorillonite clay called Maghnite–H+ (Mag–H+ as an efficient catalyst. The effect of the amount of catalyst and of time on the polymerization yield and on the viscosity of the polymers was studied. Compared with conventional static interfacial polymerization, the microwave-radiation polymerization reaction proceeded rapidly and was completed within 35 s. The conjugated polymer was characterized by means of 1H-NMR, X-ray diffraction, FT-IR spectroscopy and AFM. The X-ray data showed the presence of a backbone form of the [(pyrrole-2,5-diyl-co-(benzylidene] formed.

Nanocrystalline soft ferromagnetic Ni-Co-P thin film on Al alloy by low temperature electroless deposition

International Nuclear Information System (INIS)

Aal, A. Abdel; Shaaban, A.; Hamid, Z. Abdel

2008-01-01

Soft ferromagnetic ternary Ni-Co-P films were deposited onto Al 6061 alloy from low temperature Ni-Co-P electroless plating bath. The effect of deposition parameters, such as time and pH, on the plating rate of the deposit were examined. The results showed that the plating rate is a function of pH bath and the highest coating thickness can be obtained at pH value from 8 to10. The surface morphology, phase structure and the magnetic properties of the prepared films have been investigated using scanning electron microscopy (SEM), X-ray diffraction analysis (XRD) and vibrating magnetometer device (VMD), respectively. The deposit obtained at optimum conditions showed compact and smooth with nodular grains structure and exhibited high magnetic moments and low coercivety. Potentiodynamic polarization corrosion tests were used to study the general corrosion behavior of Al alloys, Ni-P and Ni-Co-P coatings in 3.5% NaCl solution. It was found that Ni-Co-P coated alloy demonstrated higher corrosion resistance than Ni-P coating containing same percent of P due to the Co addition. The Ni-Co-P coating with a combination of high corrosion resistance, high hardness and excellent magnetic properties would be expected to enlarge the applications of the aluminum alloys

Photocatalytic Degradation of Eosin Yellow Using Poly(pyrrole-co-aniline-Coated TiO2/Nanocellulose Composite under Solar Light Irradiation

Directory of Open Access Journals (Sweden)

T. S. Anirudhan

2015-01-01

Full Text Available The present study describes the feasibility of a novel adsorbent cum photocatalyst, poly(pyrrole-co-aniline-coated TiO2/nanocellulose composite (P(Py-co-An-TiO2/NCC, to remove eosin yellow (EY from aqueous solutions. The removal of EY was investigated by batch adsorption followed by photocatalysis. The effect of various adsorption parameters like adsorbent dose, pH, contact time, initial concentration, and ionic strength has been optimized for treating effluents from the dye industry. Adsorption of EY reached maximum at pH 4.5 and complete removal of dye was achieved using 3.5 g/L of P(Py-co-An-TiO2/NCC. Adsorption equilibrium data were fitted with Langmuir and Fritz-Schlunder isotherm models and the kinetics of adsorption follows a second-order mechanism. The adsorption capacity of P(Py-co-An-TiO2/NCC was found to be 3.39 × 10−5 mol/g and reached equilibrium within 90 min. The photocatalytic degradation of adsorbed dye under sunlight was possible and about 92.3% of dye was degraded within 90 min. The reusability of P(Py-co-An-TiO2/NCC was also investigated. The results indicate that P(Py-co-An-TiO2/NCC is the best material for the wiping out of EY from aqueous solutions.

Characterization of poly pyrrole/montmorillonite electro polymerised onto Pt; Caracterizacao de filmes PPy/montmorilonita eletropolimerizados sobre Pt

Energy Technology Data Exchange (ETDEWEB)

Castagno, K.R.L., E-mail: katiarlc@pelotas.ifsul.edu.b [Instituto Federal Sul-rio-grandense (IFSul), RS (Brazil). Dept. de Quimica; Azambuja, D.S.; Dalmoro, V.; Mauller, R.S. [Universidade Federal do Rio Grande do Sul (UFRGS), Pelotas, RS (Brazil). Inst. de Quimica

2010-07-01

In this study films of polypyrrole/montmorillonite (PPy/MT) were electropolymerized on platinum in order to evaluate the performance of this technique in the preparation of nanocomposite materials and to determine the thermal properties and conductivity of the composites. The films were synthesized from a solution containing pyrrole, dodecylbenzene sulfonate, acid and two types of clays: montmorillonite-Na + (MT-Na) and montmorillonite-30B (MT-M). The characterization of the films we have used FT-IR, TEM, XRD, TGA, DSC and resistivity measurement by the four-point van der Pauw method. The study showed that the adopted method of exfoliation and the electropolymerization method used, allows obtaining nanocomposite materials. Analyses of FT-IR, TEM and XRD show that the clays are exfoliated in the polymer matrix. Thermal analysis of the films indicates that the addition of clay reflects an enhancement in the thermal properties of the matrix of PPy, but decreases the conductivity of the same. (author)

Tuning microstructure and magnetic properties of electrodeposited CoNiP films by high magnetic field annealing

Energy Technology Data Exchange (ETDEWEB)

Wu, Chun; Wang, Kai [Key Laboratory of Electromagnetic Processing of Materials (Ministry of Education), Northeastern University, Shenyang 110819 (China); Li, Donggang, E-mail: lidonggang@smm.neu.edu.cn [School of Metallurgy, Northeastern University, Shenyang 110819 (China); Lou, Changsheng [School of Materials Science and Engineering, Shenyang Ligong University, Shenyang 110159 (China); Zhao, Yue; Gao, Yang [Key Laboratory of Electromagnetic Processing of Materials (Ministry of Education), Northeastern University, Shenyang 110819 (China); Wang, Qiang, E-mail: wangq@mail.neu.edu.cn [Key Laboratory of Electromagnetic Processing of Materials (Ministry of Education), Northeastern University, Shenyang 110819 (China)

2016-10-15

A high magnetic field (up to 12 T) has been used to anneal 2.6-µm-thick Co{sub 50}Ni{sub 40}P{sub 10} films formed by pulse electrodeposition. The effects of high magnetic field annealing on the microstructure and magnetic properties of CoNiP thin films have been investigated. It was found that a high magnetic field accelerated a phase transformation from fcc to hcp and enhanced the preferred hcp-(002) orientation during annealing. Compared with the films annealed without a magnetic field, annealing at 12 T decreased the surface particle size, roughness, and coercivity, but increased the saturation magnetization and remanent magnetization of CoNiP films. The out-of-plane coercivity was higher than that the in-plane for the as-deposited films. After annealing without a magnetic field, the out-of-plane coercivity was equal to that of the in-plane. However, the out-of-plane coercivity was higher than that of the in-plane when annealing at 12 T. These results indicate that high magnetic field annealing is an effective method for tuning the microstructure and magnetic properties of thin films. - Highlights: • High magnetic field annealing accelerated phase transformation from γ to ε. • High magnetic field annealing enhanced preferred hcp-(002) orientation. • High magnetic field annealing decreased particle size, roughness and coercivity. • High magnetic field annealing increased the saturation and remanent magnetization.

A structural study of effects of NiP seed layer on the magnetic properties of CoCrPt/Ti/NiP perpendicular magnetic films

CERN Document Server

Sun, C J; Wang, J P; Soo, E W; Noh, D Y; Je, J H; Hwu, Y K

2003-01-01

The CoCrPt/Ti/NiP films for perpendicular magnetic recording were studied using X-ray scattering and anomalous X-ray scattering. When the NiP seed layer was used, the long range order of the texture peak of the magnetic film decreased and less Co was associated with this Bragg order. The structural results were consistent with the observed increased coercivity and decreased magnetization due to the increased magnetic grain isolation caused by the presence of NiP seed layer.

Co-P-B catalyst thin films prepared by electroless and pulsed laser deposition for hydrogen generation by hydrolysis of alkaline sodium borohydride: A comparison

International Nuclear Information System (INIS)

Patel, N.; Fernandes, R.; Bazzanella, N.; Miotello, A.

2010-01-01

Co-P-B catalyst thin films have been synthesized on Ni-foam and glass substrate by using electroless deposition (ED) and pulsed laser deposition (PLD) respectively. The efficiency of these catalyst films was tested by catalytic hydrolysis of NaBH 4 for H 2 generation. While the chemically produced Co-P-B film on Ni-foam shows similar activity as that of their corresponding powder, the Co-P-B film deposited by PLD exhibits much superior H 2 generation rate as compared to Co-P-B powder. We attribute this increased efficiency to the special features of the Co-P-B films which are in the form of nanoparticle-assembled films, a peculiar characteristic of PLD films for appropriate choice of the pulse laser parameters. The surface nanoparticle-configuration increases the active surface area and also favors electronic exchange mechanisms to promote hydrolysis process for H 2 gas generation. The films deposited by using laser energy density of 3 J/cm 2 show the highest activity in connection to the best configuration of the ablated nanoparticles. Different numbers of Co-P-B layers were deposited on Ni-foam by ED and it was found that at least four layers are required for complete coverage of the foam to have the best activity.

STUDY OF ELECTROPOLIMERIZATION PROCESSES OF PYRROLE BY CYCLIC VOLTAMMETRIC TECHNIQUE

Directory of Open Access Journals (Sweden)

Adhitasari Suratman

2010-06-01

Full Text Available Electropolymerization processes and electrochemical properties of polypyrrole as electroactive polymer have been studied by cyclic voltammetric technique. Pyrrole was electropolymerized to form polypyrrole in water-based solvent containing sodium perchlorate as supporting electrolyte in several pH values. The pH of the solutions were varied by using Britton Robinson buffer. The results showed that oxidation potential limit of electropolymerization processes of pyrrole was 1220 mV vs Ag/AgCl reference electrode. It can be seen that cyclic voltammetric respon of polypyrrole membrane that was prepared by electropolymerization processes of pyrrole at the scanning rate of 100 mV/s was stable. While the processes of pyrrole electropolymerization carried out at the variation of pH showed that the best condition was at the pH range of 2 - 6.   Keywords: polypyrolle, electropolymer, voltammetric technique

Structural and morphological modifications of the Co-thin films caused by magnetic field and pH variation

International Nuclear Information System (INIS)

Franczak, Agnieszka; Levesque, Alexandra; Bohr, Frederic; Douglade, Jacques; Chopart, Jean-Paul

2012-01-01

Highlights: ► Co electrodeposits were obtained at high electrolyte temperature under applied magnetic field. ► The temperature is commonly used in the industrial process. ► The effects of magnetic field up to 1 T and pH on structure and morphology were investigated. ► The high process temperature enhances HER which is diminishing by the magnetic field application. - Abstract: Cobalt films were deposited by use of the electrochemical process from a cobalt (II) sulfate solution on a titanium electrode and characterized by scanning electron microscopy (SEM), atomic force microscopy (AFM) and X-ray diffraction (XRD). The experiments at electrolyte temperature of 50 °C were performed which is commonly used in the industrial process. The effects of pH and low uniform magnetic field up to 1 T on structure and morphology changes were investigated. The detected phase composition indicates the presence of both phases: hexagonal centered packed and face centered cubic independent on the pH value and the applied magnetic field amplitude. Calculation of the orientation index of Co phase shows the preferential orientation in the films obtained at higher pH. SEM micro-imagines have shown the nucleus shape transition from coarse-grained to needle-shaped dependent on the application of B-field as well as on the pH variation in the case of higher pH level. Co-films obtained from the electrolyte of low pH were characterized by the fine-grained morphology which was not modified by the influence of magnetic field. AFM images proved the effect on roughness of the Co-films which is closely related with the obtained morphology.

Microwave absorption property of the diatomite coated by Fe-CoNiP films

Science.gov (United States)

Yan, Zhenqiang; Cai, Jun; Xu, Yonggang; Zhang, Deyuan

2015-08-01

A bio-absorbent of Fe-CoNiP coated on the diatomite was fabricated by way of electroless plating of CoNiP and subsequent chemical vapor deposition of Fe. The surface morphology and composition of the above-mentioned diatomite particles at different stage were characterized with the scanning electron microscopy and the energy spectrum analysis respectively, and the results showed that the diatomite was successfully coated with CoNoP and Fe (carbony iron). The complex permittivity and permeability of composites filled with the bio-absorbent and paraffin was measured in frequency range of 2-18 GHz, and then the microwave reflection loss (RL) and the shielding effectiveness (SE) were calculated. The results showed that the permittivity and the permeability were both enlarged as Fe films were coated onto the CoNiP-coated diatomite, which was attributed to the excellent electromagnetic property of carbonyl irons. The composites made with the Fe-CoNiP diatomite had a better absorbing property (minimum RL -11.0 dB) as well as the shielding property (maximum SE 5.6 dB) at thickness 2 mm. It indicated the absorption property was mainly due to the attenuation on the microwave, and the Fe-CoNiP diatomite could be an effective absorbent with low-density.

Poly (pyrrole-co-aniline) hollow nanosphere supported Pd nanoflowers as high-performance catalyst for methanol electrooxidation in alkaline media

International Nuclear Information System (INIS)

Fard, Leyla Abolghasemi; Ojani, Reza; Raoof, Jahan Bakhsh; Zare, Ehsan Nazarzadeh; Lakouraj, Moslem Mansour

2017-01-01

In this work, first poly (pyrrole-co-aniline) (PPCA) hollow nanosphere (HN) as a catalyst support material is fabricated through in-situ emulsion polymerization. Then we reported a one-step and template-free approach to fabricate Pd NFs on a PPCA HN coated glassy carbon electrode by a facile electrochemical approach. Several techniques such as FTIR (Fourier transform infrared spectroscopy), SEM (scanning electron microscopy) and EDS (energy dispersive spectroscopy) were utilized for the characterization of the synthesized materials. The catalytic performance of Pd NFs/PPCA HN catalyst is evaluated by cyclic voltammetry, chronoamperometry and electrochemical impedance spectroscopy toward methanol oxidation as a model reaction in alkaline media. The comparison of specific activities for Pd NFs/PPCA HN (1.79 mA cm"−"2), Pd NFs/PPy (1.28 mA cm"−"2), Pd NFs/PANI (0.93 mA cm"−"2) and Pd NFs (0.78 mA cm"−"2) shows that the PPCA supported Pd NFs with high surface area exhibits the excellent electrocatalytic activity than other electrodes for the electro-oxidation reaction in alkaline media. This might be due to the easier charge transfer at conductive copolymer interfaces, higher electrochemically accessible surface areas and electronic conductivity. This strategy provides a promising platform for direct methanol fuel cells. - Highlights: • Pd nanoflowers supported on poly (pyrrole-co-aniline) hollow nanosphere is prepared by a facile electrochemical approach. • The as-prepared nanocatalyst displays the enhanced electrocatalytic activity and stability for methanol oxidation. • The high performance is attributed to facile electron transfer on poly (pyrrole-co-aniline) hollow nanosphere substrate.

Enhancement in performance of polycarbazole-graphene nanocomposite Schottky diode

International Nuclear Information System (INIS)

Pandey, Rajiv K.; Singh, Arun Kumar; Prakash, Rajiv

2013-01-01

We report formation of polycarbazole (PCz)–graphene nanocomposite over indium tin oxide (ITO) coated glass substrate using electrochemical technique for fabrication of high performance Schottky diodes. The synthesized nanocomposite is characterized before fabrication of devices for confirmation of uniform distribution of graphene nanosheets in the polymer matrix. Pure PCz and PCz-graphene nanocomposites based Schottky diodes are fabricated of configuration Al/PCz/ITO and Al/PCz-graphene nanocomposite/ITO, respectively. The current density–voltage (J-V) characteristics and diode performance parameters (such as the ideality factor, barrier height, and reverse saturation current density) are compared under ambient condition. Al/PCz-graphene nanocomposite/ITO device exhibits better ideality factor in comparison to the device formed using pure PCz. It is also observed that the Al/PCz-graphene nanocomposite/ITO device shows large forward current density and low turn on voltage in comparison to Al/PCz/ITO device

Microwave absorption property of the diatomite coated by Fe-CoNiP films

International Nuclear Information System (INIS)

Yan, Zhenqiang; Cai, Jun; Xu, Yonggang; Zhang, Deyuan

2015-01-01

Highlights: • The bio-absorbent coated Fe-CoNiP was fabricated by electroless and CVD. • The EM parameters were enlarged as Fe coated on the diatomite. • The coating CIPs play a key role in the enhancement mechanism. • The Fe-CoNiP diatomite had a better absorbing and shielding properties. - Abstract: A bio-absorbent of Fe-CoNiP coated on the diatomite was fabricated by way of electroless plating of CoNiP and subsequent chemical vapor deposition of Fe. The surface morphology and composition of the above-mentioned diatomite particles at different stage were characterized with the scanning electron microscopy and the energy spectrum analysis respectively, and the results showed that the diatomite was successfully coated with CoNoP and Fe (carbony iron). The complex permittivity and permeability of composites filled with the bio-absorbent and paraffin was measured in frequency range of 2–18 GHz, and then the microwave reflection loss (RL) and the shielding effectiveness (SE) were calculated. The results showed that the permittivity and the permeability were both enlarged as Fe films were coated onto the CoNiP-coated diatomite, which was attributed to the excellent electromagnetic property of carbonyl irons. The composites made with the Fe-CoNiP diatomite had a better absorbing property (minimum RL −11.0 dB) as well as the shielding property (maximum SE 5.6 dB) at thickness 2 mm. It indicated the absorption property was mainly due to the attenuation on the microwave, and the Fe-CoNiP diatomite could be an effective absorbent with low-density

Microwave absorption property of the diatomite coated by Fe-CoNiP films

Energy Technology Data Exchange (ETDEWEB)

Yan, Zhenqiang; Cai, Jun; Xu, Yonggang, E-mail: xuyonggang221@163.com; Zhang, Deyuan

2015-08-15

Highlights: • The bio-absorbent coated Fe-CoNiP was fabricated by electroless and CVD. • The EM parameters were enlarged as Fe coated on the diatomite. • The coating CIPs play a key role in the enhancement mechanism. • The Fe-CoNiP diatomite had a better absorbing and shielding properties. - Abstract: A bio-absorbent of Fe-CoNiP coated on the diatomite was fabricated by way of electroless plating of CoNiP and subsequent chemical vapor deposition of Fe. The surface morphology and composition of the above-mentioned diatomite particles at different stage were characterized with the scanning electron microscopy and the energy spectrum analysis respectively, and the results showed that the diatomite was successfully coated with CoNoP and Fe (carbony iron). The complex permittivity and permeability of composites filled with the bio-absorbent and paraffin was measured in frequency range of 2–18 GHz, and then the microwave reflection loss (RL) and the shielding effectiveness (SE) were calculated. The results showed that the permittivity and the permeability were both enlarged as Fe films were coated onto the CoNiP-coated diatomite, which was attributed to the excellent electromagnetic property of carbonyl irons. The composites made with the Fe-CoNiP diatomite had a better absorbing property (minimum RL −11.0 dB) as well as the shielding property (maximum SE 5.6 dB) at thickness 2 mm. It indicated the absorption property was mainly due to the attenuation on the microwave, and the Fe-CoNiP diatomite could be an effective absorbent with low-density.

EFFECT OF THE PHASE STRUCTURE EVOLUTION ON THE PROPERTIES OF FILMS FORMED FROM PBA/P(ST-CO-MMA)COMPOSITE LATEX

Institute of Scientific and Technical Information of China (English)

无

2008-01-01

A group of heterogeneous latexes poly(butyl acrylate)/poly(styrene-co-methyl methacrylate)(PBA/P(St-co-MMA))were prepared by a semi-continuous seeded emulsion polymerization process under monomer starved conditions.The glass transition temperature(Tg)and the mechanical properties of the film formed from the composite latex changed with the evolution of the particle morphology.A photon transmission method was used to monitor the phase structure evolution of films which were prepared from core-shell PBA/P(St-co-MMA)latex at room temperature and annealed at 383 K above Tg of the polymers.In addition,the changes of the surface of the film formed from the composite latex with time at 383 K were observed by AFM.The evidence illustrated that the film formed from the core-shell latex particles was metastable.The rearrangement of the phases could occur under proper conditions.

Physicochemical properties of poly(lactic acid-co-glycolic acid film modified via blending with poly(butyl acrylate-co-methyl methacrylate

Directory of Open Access Journals (Sweden)

Guoquan Zhu

2013-01-01

Full Text Available A series of poly(lactic acid-co-glycolic acid (PLGA/poly(butyl acrylate-co-methyl methacrylate (P(BA-co-MMA blend films with different P(BA-co-MMA mole contents were prepared by casting the polymer blend solution in chloroform. Surface morphologies of the PLGAP(BA-co-MMA blend films were studied by scanning electron microscopy (SEM. Thermal, mechanical, and chemical properties of PLGAP(BA-co-MMA blend films were investigated by differential scanning calorimeter (DSC, thermogravimetric analysis (TGA, tensile tests, and surface contact angle tests. The introduction of P(BA-co-MMA could modify the properties of PLGA films.

Tumor Repression of VCaP Xenografts by a Pyrrole-Imidazole Polyamide.

Directory of Open Access Journals (Sweden)

Amanda E Hargrove

Full Text Available Pyrrole-imidazole (Py-Im polyamides are high affinity DNA-binding small molecules that can inhibit protein-DNA interactions. In VCaP cells, a human prostate cancer cell line overexpressing both AR and the TMPRSS2-ERG gene fusion, an androgen response element (ARE-targeted Py-Im polyamide significantly downregulates AR driven gene expression. Polyamide exposure to VCaP cells reduced proliferation without causing DNA damage. Py-Im polyamide treatment also reduced tumor growth in a VCaP mouse xenograft model. In addition to the effects on AR regulated transcription, RNA-seq analysis revealed inhibition of topoisomerase-DNA binding as a potential mechanism that contributes to the antitumor effects of polyamides in cell culture and in xenografts. These studies support the therapeutic potential of Py-Im polyamides to target multiple aspects of transcriptional regulation in prostate cancers without genotoxic stress.

Fabrication of calix[4]pyrrole nanofilms at the glassy carbon surface and their characterization by spectroscopic, optic and electrochemical methods

International Nuclear Information System (INIS)

Taner, Bilge; Ozcan, Emine; Ustuendag, Zafer; Keskin, Selda; Solak, Ali Osman; Eksi, Haslet

2010-01-01

meso-Octamethylcalix[4]pyrrole (CP) and meso-heptaethylcalix[4]pyrrole-meso-4-aminophenyl (4APCP) modified glassy carbon (GC) electrodes were prepared by the electrochemical oxidation in acetonitrile solution. Binding of the calix[4]pyrroles with the glassy carbon surface was investigated that it is through the etheric linkage revealed from the reflection-absorption infrared spectroscopy (RAIRS). Surface films of CP and 4APCP were investigated by cyclic voltammetry (CV), ellipsometry, X-ray photoelectron spectroscopy, RAIRS and the contact angle measurements. The thicknesses of the films were determined by ellipsometry which confirmed that the film was multilayer and homogeneous over the surface. Ellipsometric measurements also provided that the CP and 4APCP film thicknesses were 2.49 nm and 4.58 nm for 6 CV cycle modification, corresponding to 66 μF/cm 2 and 106 μF/cm 2 capacitances obtained by CV. The wetting behavior was examined by contact angle measurements and found that the hydrophobicity of the GC-4APCP surface was higher than that of GC-CP, probably due to the aromatic meso substituent present in the former.

Versatile functionalization of nanoelectrodes by oligonucleotides via pyrrole electrochemistry.

Science.gov (United States)

Descamps, Emeline; Nguyen, Khoa; Bouchain-Gautier, Christelle; Filoramo, Arianna; Goux-Capes, Laurence; Goffman, Marcello; Bourgoin, Jean-Philippe; Mailley, Pascal; Livache, Thierry

2010-11-15

Surface modification at the nanometer scale is a challenge for the future of molecular electronics. In particular, the precise anchoring and electrical addressing of biological scaffolds such as complex DNA nanonetworks is of importance for generating bio-directed assemblies of nano-objects for nanocircuit purposes. Herein, we consider the individual modification of nanoelectrodes with different oligonucleotide sequences by an electrochemically driven co-polymerization process of pyrrole and modified oligonucleotide sequences bearing pyrrole monomers. We demonstrate that this one-step technique presents the advantages of simplicity, localization of surface modification, mechanical, biological and chemical stability of the coatings, and high lateral resolution.

Fabrication of calix[4]pyrrole nanofilms at the glassy carbon surface and their characterization by spectroscopic, optic and electrochemical methods

Energy Technology Data Exchange (ETDEWEB)

Taner, Bilge; Ozcan, Emine [Selcuk University, Faculty of Science, Dept. of Chemistry, Konya (Turkey); Ustuendag, Zafer [Dumlupinar University, Faculty of Arts and Sciences, Dept. of Chemistry, Kuetahya (Turkey); Keskin, Selda [Middle East Technical University, Central Research Laboratory, Ankara (Turkey); Solak, Ali Osman, E-mail: osolak@science.ankara.edu.t [Ankara University, Faculty of Science, Department of Chemistry, Ankara (Turkey); Eksi, Haslet [Ankara University, Faculty of Science, Department of Chemistry, Ankara (Turkey)

2010-10-29

meso-Octamethylcalix[4]pyrrole (CP) and meso-heptaethylcalix[4]pyrrole-meso-4-aminophenyl (4APCP) modified glassy carbon (GC) electrodes were prepared by the electrochemical oxidation in acetonitrile solution. Binding of the calix[4]pyrroles with the glassy carbon surface was investigated that it is through the etheric linkage revealed from the reflection-absorption infrared spectroscopy (RAIRS). Surface films of CP and 4APCP were investigated by cyclic voltammetry (CV), ellipsometry, X-ray photoelectron spectroscopy, RAIRS and the contact angle measurements. The thicknesses of the films were determined by ellipsometry which confirmed that the film was multilayer and homogeneous over the surface. Ellipsometric measurements also provided that the CP and 4APCP film thicknesses were 2.49 nm and 4.58 nm for 6 CV cycle modification, corresponding to 66 {mu}F/cm{sup 2} and 106 {mu}F/cm{sup 2} capacitances obtained by CV. The wetting behavior was examined by contact angle measurements and found that the hydrophobicity of the GC-4APCP surface was higher than that of GC-CP, probably due to the aromatic meso substituent present in the former.

A complicated biocomputing system based on multi-responsive P(NIPAM-co-APBA) copolymer film electrodes and electrocatalysis of NADH.

Science.gov (United States)

Liang, Jiying; Yu, Xue; Yang, Tiangang; Li, Menglu; Shen, Li; Jin, Yue; Liu, Hongyun

2017-08-23

In this paper, poly(N-isopropylacrylamide-co-3-aminophenylboronic acid) (P(NIPAM-co-APBA)) copolymer films were successfully electropolymerized on the Au electrode surface. The electroactive probe ferrocene carboxylic acid (FCA) in solution showed reversible thermal-, glucose- and pH-responsive on-off cyclic voltammetric (CV) behaviors at the film electrodes. The comparative experiments demonstrated that the thermo-responsive property of the film electrode was ascribed to the PNIPAM component of the films, whereas the glucose- and pH-sensitive behaviors came from the PAPBA constituent. The reduced form of nicotinamide adenine dinucleotide (NADH) could be electrocatalytically oxidized by FCA at the film electrodes, which would greatly amplify the multi-responsive CV signal difference between the on and off states. On the basis of these results, a binary 4-input/4-output logic circuit was fabricated with temperature, glucose, pH and NADH as inputs and the CV responses at 4 different levels as outputs. Moreover, a ternary CONSENSUS logic circuit was established on the same platform, which was the first report on the combination of ternary logic gate and bioelectrocatalysis without using enzymes. This work provided a novel idea for constructing complicated biocomputing systems by increasing the number of inputs/outputs with multi-sensitive interfaces and by designing new types of multi-valued logic gates on the basis of bioelectrocatalysis.

2D magnetic texture analysis of Co-Cu films

Energy Technology Data Exchange (ETDEWEB)

Bayirli, Mehmet; Karaagac, Oznur; Kockar, Hakan [Balikesir Univ. (Turkey). Physics Dept.; Alper, Mursel [Uludag Univ., Bursa (Turkey). Physics Dept.

2017-08-01

The magnetic textures for the produced magnetic materials are important concepts in accordance with technical applications. Therefore, the aim of this article is to determine 2D magnetic textures of electrodeposited Co-Cu films by the measurement of hysteresis loops at the incremented angles. For that, Co-Cu films were deposited with different Co{sup 2+} in the electrolyte. In addition, the easy-axis orientation in the films from the squareness values of the angles, M{sub p}(β) obtained by the hysteresis loops have been numerically studied using the Fourier series analysis. The differences observed in the magnetic easy-axis distributions were attributed to changes of the incorporation of Co in the films with the change of Co{sup 2+} in the electrolyte. The coefficients of Fourier series (A{sub 0} and A{sub 2n}) were also computed for 2D films. It is seen that a systematic and small decrease in A{sub 0} and an obvious decrease in A{sub 2n} (n=1) were observed with increasing incorporated Co in the films. Results imply that interactions cause slightly demagnetization effect accordance with higher incorporation of Co in the films. Furthermore, the crystal structure of the Co-Cu films analysed by X-ray diffraction revealed that the films have dominantly face-centred cubic structure. Film contents analysed by energy-dispersive X-ray spectroscopy and film morphologies observed by scanning electron microscope also support the magnetic texture analysis results found by numerical computation.

2D magnetic texture analysis of Co-Cu films

International Nuclear Information System (INIS)

Bayirli, Mehmet; Karaagac, Oznur; Kockar, Hakan; Alper, Mursel

2017-01-01

The magnetic textures for the produced magnetic materials are important concepts in accordance with technical applications. Therefore, the aim of this article is to determine 2D magnetic textures of electrodeposited Co-Cu films by the measurement of hysteresis loops at the incremented angles. For that, Co-Cu films were deposited with different Co"2"+ in the electrolyte. In addition, the easy-axis orientation in the films from the squareness values of the angles, M_p(β) obtained by the hysteresis loops have been numerically studied using the Fourier series analysis. The differences observed in the magnetic easy-axis distributions were attributed to changes of the incorporation of Co in the films with the change of Co"2"+ in the electrolyte. The coefficients of Fourier series (A_0 and A_2_n) were also computed for 2D films. It is seen that a systematic and small decrease in A_0 and an obvious decrease in A_2_n (n=1) were observed with increasing incorporated Co in the films. Results imply that interactions cause slightly demagnetization effect accordance with higher incorporation of Co in the films. Furthermore, the crystal structure of the Co-Cu films analysed by X-ray diffraction revealed that the films have dominantly face-centred cubic structure. Film contents analysed by energy-dispersive X-ray spectroscopy and film morphologies observed by scanning electron microscope also support the magnetic texture analysis results found by numerical computation.

Preparation of thin α-particle sources using poly-pyrrole films functionalized by a chelating agent

International Nuclear Information System (INIS)

Mariet, C.

2000-01-01

This work takes place in the scope of analysis of the α-particle emitting elements U, Pu and Am present in compound environmental matrix like sols and sediments. The samples diversity and above all the α-ray characteristics require the analyst to implement a sequence of chemical steps in which the more restricting is the actinides concentration in a uniform and thin layer en allowing an accurately measure of alpha activity. On this account, we studied a new technique for radioactive sources preparation based on tow steps: preparation of a thin film as source support; incorporation of radioactive elements by a chelating extraction mechanism. The thin films were obtained through electro-polymerization of pyrrole monomer functionalized by an chelating ligand able to extract actinides from concentrated acidic solutions. Polymerization conditions of this monomer were perfected, then obtained films were characterized from a physico-chemical point of view. We point out their extracting properties were comparable to (retention capacity, distribution coefficient) to those of usual ion-exchange resins. The underscore of uranyl and americium nitrate complexes formed in the thin layer allowed to calculate the extraction constants in case acid extraction is negligible. Thanks to this results, the values of the coefficients distribution D U and D Am could be provided for all nitric solutions in which acid extraction is negligible. Optimal actinides retention conditions in the polymer were defined and used to settle a protocol for plutonium analysis in environmental samples. (author)

Interaction of derived polymers from pyrrole with biocompatible solutions

International Nuclear Information System (INIS)

Lopez G, O. G.

2010-01-01

This work presents a study about the synthesis by plasma, the electric properties and superficial interaction of polymers derived from pyrrole doped with Iodine with potential use as bio material. Poly-pyrrole is a semiconductor and biocompatible polymer with potential application in the development of artificial muscles and implants where the electric interaction between cells and material is an important variable. The syntheses were made at 13.5 MHz in a glass tubular reactor of 1500 cm 3 with electrodes of 6.5 cm diameter and stainless steel flanges. An electrode was connected to the RF terminal of the power supply that is combined with a matching coupling resistance. The monomer and dopant used in this work were pyrrole and Iodine respectively, in closed containers. They were vaporized and injected separately into the reactor at room temperature and 0.1 mbar. The vapors of the reagents mixed freely in the reactor. The synthesis time was 240 min at 40, 60, 80 and 100 W. The polymers were obtained as thin films adhered to the reactor walls. The films were washed and swollen with distilled water and removed from the reactor walls with a small spatula. The polymers were irradiated with gamma rays at 18 and 22 KGy. Due to the fact that the doses are cumulative, the final dose applied was 40 KGy. The polymers characterization was carried out by Fourier Transform Infrared Spectroscopy, thermogravimetric analysis (TGA), scanning electron microscopy, contact angle, electrical conductivity and X-ray diffraction. The analyses indicates that the polymers have very similar structure in almost the entire power range, showing C-O, C=C, C-H, O-H, N-H bonds with a predominantly amorphous structure. The TGA analyses showed that the material has 4 or 5 loses of material. The first one starts after that 115 C except for the material irradiated at 40 KGy, this one begins in 87 C, the second one is in the interval of 196 and 295 C, the third one between 311 and 500 C, and the last

Speeding up nanomagnetic logic by DMI enhanced Pt/Co/Ir films

Science.gov (United States)

Ziemys, Grazvydas; Ahrens, Valentin; Mendisch, Simon; Csaba, Gyorgy; Becherer, Markus

2018-05-01

We investigated a new type of multilayer film for Nanomagnetic Logic with perpendicular anisotropy (pNML) enhanced by the Dzyaloshinskii-Moriya interaction (DMI). The DMI effect provides an additional energy term and widens the design space for pNML film optimization. In this work we added an Ir layer between Co and Pt to our standard pNML multilayer (ML) film stack - [Co/Pt]x4. Multilayer stacks of films with and w/o Ir were sputtered and patterned to nanowires of 400 nm width by means of focused ion beam lithography (FIB). For comparability of the films they were tuned to show identical anisotropy for multilayer stacks with and w/o Ir. The field-driven domain wall (DW) velocity in the nanowires was measured by using wide-field MOKE microscopy. We found a strong impact of Ir on the DW velocity being up to 2 times higher compared to the standard [Co/Pt]x4 ML films. Moreover, the maximum velocity is reached at much lower magnetic field, which is beneficial for pNML operation. These results pave the way for pNML with higher clocking rates and at the same time allow a further reduce power consumption.

Nano-silver mediated polymerization of pyrrole: synthesis and gas sensing properties of polypyrrole (PPy)/Ag nano-composite.

Science.gov (United States)

Kate, Kunal H; Damkale, Shubhangi R; Khanna, P K; Jain, G H

2011-09-01

Thermal polymerization of pyrrole was performed using silver nitrate as source of silver ions followed by its conversion to Polypyrrole (PPy)/Ag nano-comoposites without using any external oxidizing agent or solvent. The formation of PPy was monitored by UV-Visible absorption spectroscopy showing a band at approximately 464 nm. XRD measurement confirmed characteristic peaks for face centered cubic (fcc) silver and presence of PPy at 2 theta of approximately 23 degrees suggesting the formation of PPy/Ag nanocomposite. Transmission electron microscopy (TEM) images showed non-aggregated spherical Ag nano-particles of about 5-10 nm. PPy/Ag thick film acts as a NH3 sensor at 100 degrees C, a H2S sensor at 250 degrees C and CO2 sensor at 350 degrees C. The thick films showed capability to recognize various gases at different operating temperature.

Simple two-step synthesis of 2,4-disubstituted pyrroles and 3,5-disubstituted pyrrole-2-carbonitriles from enones

Directory of Open Access Journals (Sweden)

Murat Kucukdisli

2014-02-01

Full Text Available The cyclocondensation of enones with aminoacetonitrile furnishes 3,4-dihydro-2H-pyrrole-2-carbonitriles which can be readily converted to 2,4-disubstituted pyrroles by microwave-induced dehydrocyanation. Alternatively, oxidation of the intermediates produces 3,5-disubstituted pyrrole-2-carbonitriles.

Spectroscopic and theoretical studies on the aromaticity of pyrrol-2-yl-carbonyl conformers

Science.gov (United States)

Dubis, Alina T.; Wojtulewski, Sławomir; Filipkowski, Karol

2013-06-01

The aromaticity of s-cis and s-trans pyrrol-2-yl carbonyl conformers was studied by FT-IR, 1H NMR spectroscopy and DFT calculations at the B3LYP/6-311++G(d,p) level of theory. The Harmonic Oscillator Model of Aromaticity (HOMA) and Nucleus Independent Chemical Shift (NICS) indices were calculated to estimate π-electron delocalization in the pyrrole ring. The usefulness of infrared spectroscopy in the evaluation of the aromaticity of the homogeneous set of pyrroles is discussed. The influence of 2-substitution on different aspects of aromaticity and stability of the pyrrol-2-yl carbonyl conformers is also discussed. It is concluded that the substitution effect of the title pyrrole derivatives can be explained on the basis of theoretical and experimental measurements of π-electron delocalization, including IR data.

GRINDING SOLVENT-FREE PAAL-KNORR PYRROLE SYNTHESIS ...

African Journals Online (AJOL)

Paal-Knorr pyrrole synthesis on smectites as recyclable and green catalysts. Bull. Chem. Soc. .... 1-Propyl-2,5-dimethyl-1H-pyrrole (8a). Oil (reported as oil .... of pyrroles catalyzed by zirconium chloride under solvent-free conditions . Ultrason.

THE EFFECT OF HIGH OVERVOLTAGES AT ELECTROCRYSTALLIZATION ON THE CORROSION RESISTANCE OF THE FILMS CO-P

Directory of Open Access Journals (Sweden)

V. O. Zabludovskyi

2009-03-01

Full Text Available Electrochemical and gravimetric methods are used in order to research the influence of high overvoltages during electroplating on corrosive and electrochemical behavior of amorphous Co-P films, which were made using deposition from water solution of an electrolyte. It is obtained that alloys, which were plated using higher overvoltages on cathode, are more corrosion-resistant.

Electrochemical determination of 4-nitrophenol at polycarbazole/N-doped graphene modified glassy carbon electrode

International Nuclear Information System (INIS)

Zhang, Yuehua; Wu, Lihua; Lei, Wu; Xia, Xifeng; Xia, Mingzhu; Hao, Qingli

2014-01-01

Graphical abstract: - Highlights: • Polycarbazole/N-doping graphene (PCZ/N-GE) composite was fabricated. • The PCZ/N-GE composite shows good electrocatalytic activity to 4-nitrophenol. • PCZ/N-GE modified electrode was used for determination of 4-nitrophenol. • The proposed sensor exhibits good sensitivity, stability and reproducibility. - Abstract: Polycarbazole (PCZ)/nitrogen-doped graphene (N-GE) composite was prepared by electropolymerization of carbazole on the N-GE modified glass carbon electrode (N-GE/GCE) for fabricating a novel electrochemical sensor for 4-nitrophenol (4-NP). The PCZ/N-GE shows high conductivity and well-distributed nanostructure. The redox behavior of 4-NP at a PCZ/N-GE/GCE was investigated in acetate buffer solution by cyclic voltammetry (CV), compared with the bare GCE, reduced graphene oxide (RGO), N-GE and PCZ modified GCEs. The results indicate that all modified electrodes show the enhanced reduction peak currents. However, the PCZ/N-GE/GCE exhibits the highest peak current and most positive reduction potential of 4-NP, which reflects the PCZ/N-GE composite has the best electrocatalytic activity towards 4-NP. The enhanced electrochemical performance of PCZ/N-GE and the electrocatalytic activity to 4-NP are contributed to the synergic effect of PCZ and N-GE with highly conductivity and large surface area, which can greatly facilitate the electron-transfer processes between the electrolyte and electrode. An electrochemical sensor for 4-NP was developed based on the PCZ/N-GE modified electrode under the optimized conditions. The reduction peak current was linear with the concentration of 4-NP in the range of 8 × 10 -7 ∼2 × 10 -5 M. The low detection limit of the sensor was estimated to be 0.062 μM (S/N = 3). The sensor based on PCZ/N-GE/GCE was also applied to the detection of 4-NP in real water samples

INFLUENCE OF ELECTROPOLYMERIZATION METHOD ON MORPHOLOGIES AND CAPACITIVE PROPERTIES OF POLYPYRROLE FILMS GROWING ON SILICON

OpenAIRE

IMENE CHIKOUCHE; ALI SAHARI; AHMED ZOUAOUI

2014-01-01

Two methods of Pyrrole electropolymerization were investigated to prepare polypyrrole films growing onto n-doped silicon n-Si (111): Polypyrrole films prepared by galvanostatic method exhibits toroidal morphology for thin films, and mixture of toroidal and globular morphologies for thick films. Polypyrrole films obtained from this method were characterized by lower surface roughness. Electropolymerization of pyrrole by potentiodynamic method provided Polypyrrole films with beans-like structur...

Syntheses of Calix[4]Pyrroles by Amberlyst-15 Catalyzed Cyclocondensations of Pyrrole with Selected Ketones

Directory of Open Access Journals (Sweden)

Tanuja Bisht

2007-11-01

Full Text Available A facile and efficient protocol is reported for the synthesis of calix[4]pyrrolesand N-confused calix[4]pyrroles in moderate to excellent yields by reaction of dialkyl orcycloalkyl ketones with pyrrole catalyzed by reusable AmberlystTM-15 under eco-friendlyconditions.

Characterization of poly pyrrole/montmorillonite electro polymerised onto Pt

International Nuclear Information System (INIS)

Castagno, K.R.L.; Azambuja, D.S.; Dalmoro, V.; Mauller, R.S.

2010-01-01

In this study films of polypyrrole/montmorillonite (PPy/MT) were electropolymerized on platinum in order to evaluate the performance of this technique in the preparation of nanocomposite materials and to determine the thermal properties and conductivity of the composites. The films were synthesized from a solution containing pyrrole, dodecylbenzene sulfonate, acid and two types of clays: montmorillonite-Na + (MT-Na) and montmorillonite-30B (MT-M). The characterization of the films we have used FT-IR, TEM, XRD, TGA, DSC and resistivity measurement by the four-point van der Pauw method. The study showed that the adopted method of exfoliation and the electropolymerization method used, allows obtaining nanocomposite materials. Analyses of FT-IR, TEM and XRD show that the clays are exfoliated in the polymer matrix. Thermal analysis of the films indicates that the addition of clay reflects an enhancement in the thermal properties of the matrix of PPy, but decreases the conductivity of the same. (author)

Ordering effects in benzo[1,2-b:4,5-b']difuran-thieno[3,4-c]pyrrole-4,6- dione polymers with >7% solar cell efficiency

KAUST Repository

Warnan, Julien

2014-05-15

Benzo[1,2-b:4,5-b\\']difuran-thieno[3,4-c]pyrrole-4,6-dione (PBDFTPD) polymers prepared by microwave-assisted synthesis can achieve power conversion efficiencies (PCEs) >7% in bulk-heterojunction solar cells with phenyl-C61/71-butyric acid methyl ester (PCBM). In "as-cast" PBDFTPD-based devices solution-processed without a small-molecule additive, high PCEs can be obtained in spite of the weak propensity of the polymers to self-assemble and form π-aggregates in thin films. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

pyrroles

Indian Academy of Sciences (India)

and various aldehydes to afford 4H-pyrano[3,2-b]pyrrole derivatives in moderate to good yield using ferric .... (pyran C5), 122.8, 122.4, 128.9, 132.7, 133.0, 141.6. (Ar-C), 179.0 (pyran C2). 2.2f ..... After Michael-type addition of malononitrile.

Magnetic properties of ultrathin Co/Ge(111) and Co/Ge(100) films

International Nuclear Information System (INIS)

Cheng, W. C.; Tsay, J. S.; Yao, Y. D.; Lin, K. C.; Yang, C. S.; Lee, S. F.; Tseng, T. K.; Neih, H. Y.

2001-01-01

The orientation of the magnetization and the occurrence of interfacial ferromagnetic inactive layers for ultrathin Co films grown on Ge(111) and Ge(100) surfaces have been studied using the in situ surface magneto-optic Kerr effect. On a Ge(111) substrate, cobalt films (≤28 monolayers) with in-plane easy axis of magnetization have been observed; however, on a Ge(100) substrate, ultrathin Co films (14 - 16 monolayers) with canted out-of-plane easy axis of magnetization were measured. The ferromagnetic inactive layers were formed due to the intermixing of Co and Ge and lowering the Curie temperature by reducing Co film thickness. The Co - Ge compound inactive layers were 3.8 monolayers thick for Co films grown on Ge(111) and 6.2 monolayers thick for Co films deposited on Ge(100). This is attributed to the difference of the density of surface atoms on Ge(111) and Ge(100). [copyright] 2001 American Institute of Physics

Effect of Sb content on the thermoelectric properties of annealed CoSb_3 thin films deposited via RF co-sputtering

International Nuclear Information System (INIS)

Ahmed, Aziz; Han, Seungwoo

2017-01-01

Graphical abstract: The X-ray diffraction patterns and temperature dependence of the Seebeck coefficient of the annealed Co–Sb thin films. - Highlights: • CoSb_3 phase thin films were prepared using RF co sputtering method. • Thin film thermoelectric properties were hugely dependent on Sb content. • All thin films shows n-type conduction behavior at high temperatures. • The thin films with excess Sb possess the largest Seebeck coefficient. • The thin films with CoSb_2 phase possess the largest power factor. - Abstract: A series of CoSb_3 thin films with Sb contents in the range 70–79 at.% were deposited at room temperature via RF co-sputtering. The thin films were amorphous in the as-deposited state and annealed at 300 °C for 3 h to obtain crystalline samples. The annealed thin films were characterized using scanning electron microscopy and X-ray diffraction (XRD), and these data indicate that the films exhibited good crystallinity. The XRD patterns indicate single-phase CoSb_3 thin films in the Sb-rich samples. For the Sb-deficient samples, however, mixed-phase thin films consisting of CoSb_2 and CoSb_3 components were obtained. The electrical and thermoelectric properties were measured at temperatures up to 760 K and found to be highly sensitive to the phases that were present. We observed a change in the thermoelectric properties of the films from p-type at low temperatures to n-type at high temperatures, which indicates potential applications as n-type thermoelectric thin films. A large Seebeck coefficient and power factor was obtained for the single-phase CoSb_3 thin films. The CoSb_2 phase thin films were also found to possess a significant Seebeck coefficient, which coupled with the much smaller electrical resistivity, provided a larger power factor than the single-phase CoSb_3 thin films. We report maximum power factor of 7.92 mW/m K"2 for the CoSb_2-containing mixed phase thin film and 1.26 mW/m K"2 for the stoichiometric CoSb_3 thin film.

The nonadiabatic deactivation paths of pyrrole

International Nuclear Information System (INIS)

Barbatti, Mario; Vazdar, Mario; Aquino, Adelia J. A.; Eckert-Maksic, Mirjana; Lischka, Hans

2006-01-01

Multireference configuration interaction (MRCI) calculations have been performed for pyrrole with the aim of providing an explanation for the experimentally observed photochemical deactivation processes. Potential energy curves and minima on the crossing seam were determined using the analytic MRCI gradient and nonadiabatic coupling features of the COLUMBUS program system. A new deactivation mechanism based on an out-of-plane ring deformation is presented. This mechanism directly couples the charge transfer 1 ππ* and ground states. It may be responsible for more than 50% of the observed photofragments of ππ*-excited pyrrole. The ring deformation mechanism should act complementary to the previously proposed NH-stretching mechanism, thus offering a more complete interpretation of the pyrrole photodynamics

Adsorption characteristics and polymerization of pyrrole on Y-zeolites

Energy Technology Data Exchange (ETDEWEB)

Matsumoto, Akihiko; Kitajima, Tsutomu; Tsutsumi, Kazuo

1999-10-26

Conductive polymers have attracted considerable interest from the viewpoint of their electrochemical aspects and have been investigated for application in novel devices such as solid electrolyte cells and molecular electronic devices. Adsorption characteristics and polymerization of pyrrole on Y-zeolites of different cation types (NaY, HY, and CuY) have been investigated in connection with adsorption behavior, in situ IR spectroscopy, and EPR spectroscopy. Adsorption of pyrrole on NaY is physisorption giving no significant changes in IR and EPR spectra. In the adsorption on HY and CuY, the formation of pyrrole oligomers or polymers is observed. Pyrrole oligomer formed on HY is a nonconjugated one, which gives no EPR signal. In the case of CuY, EPR signal assigned to polaron of polypyrrole was observed at g = 2.008 by the pyrrole adsorption. The relationship between the amount of the spin of g = 2.008 and the adsorbed amount of pyrrole was linear even at the number of pyrrole exceeding that of Cu{sub 2+}, which suggests that the polymerization giving conjugated polypyrrole would take place on Cu{sup 2+} sites and the polypyrrole of aromatic form would be oxidized to quinoid form to give polaron on CuY surface.

Effect of Sb content on the thermoelectric properties of annealed CoSb{sub 3} thin films deposited via RF co-sputtering

Energy Technology Data Exchange (ETDEWEB)

Ahmed, Aziz, E-mail: aziz_ahmed@ust.ac.kr [Department of Nano-Mechatronics, Korea University of Science and Technology (UST), 217 Gajeong-ro, Yuseong-gu, Daejeon, 305-350 (Korea, Republic of); Department of Nano-Mechanics, Korea Institute of Machinery and Materials (KIMM), 156 Gajeongbuk-ro, Yuseong-gu, Daejeon, 305-343 (Korea, Republic of); Han, Seungwoo, E-mail: swhan@kimm.re.kr [Department of Nano-Mechatronics, Korea University of Science and Technology (UST), 217 Gajeong-ro, Yuseong-gu, Daejeon, 305-350 (Korea, Republic of); Department of Nano-Mechanics, Korea Institute of Machinery and Materials (KIMM), 156 Gajeongbuk-ro, Yuseong-gu, Daejeon, 305-343 (Korea, Republic of)

2017-06-30

Graphical abstract: The X-ray diffraction patterns and temperature dependence of the Seebeck coefficient of the annealed Co–Sb thin films. - Highlights: • CoSb{sub 3} phase thin films were prepared using RF co sputtering method. • Thin film thermoelectric properties were hugely dependent on Sb content. • All thin films shows n-type conduction behavior at high temperatures. • The thin films with excess Sb possess the largest Seebeck coefficient. • The thin films with CoSb{sub 2} phase possess the largest power factor. - Abstract: A series of CoSb{sub 3} thin films with Sb contents in the range 70–79 at.% were deposited at room temperature via RF co-sputtering. The thin films were amorphous in the as-deposited state and annealed at 300 °C for 3 h to obtain crystalline samples. The annealed thin films were characterized using scanning electron microscopy and X-ray diffraction (XRD), and these data indicate that the films exhibited good crystallinity. The XRD patterns indicate single-phase CoSb{sub 3} thin films in the Sb-rich samples. For the Sb-deficient samples, however, mixed-phase thin films consisting of CoSb{sub 2} and CoSb{sub 3} components were obtained. The electrical and thermoelectric properties were measured at temperatures up to 760 K and found to be highly sensitive to the phases that were present. We observed a change in the thermoelectric properties of the films from p-type at low temperatures to n-type at high temperatures, which indicates potential applications as n-type thermoelectric thin films. A large Seebeck coefficient and power factor was obtained for the single-phase CoSb{sub 3} thin films. The CoSb{sub 2} phase thin films were also found to possess a significant Seebeck coefficient, which coupled with the much smaller electrical resistivity, provided a larger power factor than the single-phase CoSb{sub 3} thin films. We report maximum power factor of 7.92 mW/m K{sup 2} for the CoSb{sub 2}-containing mixed phase thin film and 1

Conjugated and fluorescent polymer based on dansyl-substituted pyrrole prepared by electrochemical polymerization in acetonitrile containing boron trifluoride diethyl etherate

International Nuclear Information System (INIS)

Almeida, Andresa K.A.; Dias, Jéssica M.M.; Silva, Ana Julia C.; Santos, Diego P.; Navarro, Marcelo; Tonholo, Josealdo; Goulart, Marília O.F.; Ribeiro, Adriana S.

2014-01-01

Graphical abstract: - Highlights: • A fluorescent pyrrole derivative bearing a dansyl substituent (PyPDG) was synthesized. • PyPDG was electropolymerized onto ITO in (C 4 H 9 ) 4 NBF 4 /CH 3 CN/BFEE mixed electrolyte. • The resulting polymer (PPyPDG) films displayed electrochromic behavior. • PPyPDG is a good green light emitter material. - Abstract: A fluorescent pyrrole derivative bearing a dansyl substituent was prepared by a simple synthetic route and electropolymerized onto Indium Tin Oxide (ITO) electrodes. The presence of the dansyl group in the monomer precursor prevents the electropolymerization in usual systems, such as (C 4 H 9 ) 4 NBF 4 in acetonitrile (CH 3 CN). For this reason, it was added 20% boron trifluoride diethyl etherate (BFEE) to this system, to achieve electropolymerization. The resulting poly[3-(N-pyrrolyl)propyl dansylglycinate] (PPyPDG) films displayed electrochromic behavior. Their color varied from greenish-yellow, in the neutral state, to greyish-green, in the oxidized state; moreover PPyPDG is a good green light emitter material. Therefore, PPyPDG films might be potentially applicable in displays and optoelectronic devices

Gold nanoparticle/nickel oxide/poly(pyrrole-N-propionic acid hybrid multilayer film: Electrochemical study and its application in biosensing

Directory of Open Access Journals (Sweden)

T. Karazehir

2017-06-01

Full Text Available The present study describes the fabrication of Indium Tin Oxide /gold nanoparticles/nickel oxide/poly(Pyrrole-N-propionic acid (ITO/GNPs/NiO/poly(PPA multilayered film, and its modification with Tyrosinase (Ty. The ITO/GNPs/NiO/poly(PPA electrode was fabricated by sequential electrochemical assembly onto ITO substrate which electrochemical deposition provides a facile, inexpensive technique for synthesis of multilayered film within the adherent morphology with controllable film thickness. Cyclic voltammetry (CV, Fourier transform infrared spectroscopy-attenuated total reflectance (FTIR-ATR, scanning electron microcopy (SEM, and atomic force microcopy (AFM were used to characterize the film assembly processes. The properties of a semiconductor/electrolyte interface were investigated based on the Mott–Schottky (M-S approach for the modified electrodes, with the flat band potential (EFB according to the potential intercept and the carrier density (ND according to the linear slopes. The ND and EFB of ITO/GNPs/NiO/poly(PPA were obtained as 2.48·1021 cm–3 and 0.26 V, respectively. Tyrosinase was immobilized using carbodiimide coupling reaction. The bioelectrode was characterized by FTIR-ATR, SEM, AFM, electrochemical impedance spectroscopy (EIS. A Randles equivalent circuit was introduced for modeling the performance of impedimetric biosensing for the detection of the dopamine (DP and the interface of bioelectrode/electrolyte. The EIS of the ITO/GNPs/NiO/poly(PPA-Ty exhibited significant changes in the charge transfer resistance (RCT value toward the detection of dopamine over a linear range of 80 µM to 0.2 mM with a limit of detection (LOD of 5.46 µM.

Pyrrole alkaloids from the fruits of Morus alba.

Science.gov (United States)

Kim, Seon Beom; Chang, Bo Yoon; Hwang, Bang Yeon; Kim, Sung Yeon; Lee, Mi Kyeong

2014-12-15

Phytochemical investigation of the fruits of Morus alba afforded seventeen pyrrole alkaloids including five new compounds. The structures of five new pyrrole alkaloids, named morroles B-F (4, 5, 7, 16 and 17), were determined on the basis of spectroscopic interpretations. 4-[Formyl-5-(hydroxymethyl)-1H-pyrrol-1-yl]butanoate (2) was synthesized by chemical reaction but first isolated from nature. Among isolated compounds, compounds 6 and 14 significantly inhibited pancreatic lipase activity. Copyright © 2014 Elsevier Ltd. All rights reserved.

Antikken på film

DEFF Research Database (Denmark)

Krasilnikoff, Jens

2012-01-01

Review af forskning om den græsk-romerske oldtid på film. Dertil en skitse til videre arbejde med antikken på film ud fra et historiefagligt og kulturhistorisk udgangspunkt.......Review af forskning om den græsk-romerske oldtid på film. Dertil en skitse til videre arbejde med antikken på film ud fra et historiefagligt og kulturhistorisk udgangspunkt....

Magnetic anisotropies in SmCo thin films

International Nuclear Information System (INIS)

Chen, K.

1993-01-01

A systemic study of the deposition processes and magnetic properties for the Sm-Co film system has been carried out. Films of Sm-Co system with various magnetic anisotropies have been synthesized through sputter deposition in both crystalline and amorphous phases. The origins of various anisotropies have been studied. Thermalized sputter deposition process control was used to synthesize Fe enriched Sm-Co films with rhombohedral Th 2 Zn 17 type structure. The film exhibited unusually strong textures with the crystallographic c axes of the crystallites aligned in the film plane. A large anisotropy was resulted with easy axis in the film plane. A well defined and large in-the-film-plane anisotropy of exceptionally high value of 3.3 x 10 6 erg/cm 3 has been obtained in the amorphous SmCo films by applying a magnetic field in the film plane during deposition. It was found that the in-the-film-plane anisotropy depended essentially on the applied field and Sm concentration. For films not synthesized through thermallized sputtering, the easy axis of the film could reoriented. A perpendicular anisotropy was also presented in the film synthesized through thermallized sputtering deposition. A large in-plane anisotropy was obtained in films deposited above ambient temperatures. It was concluded that the surface induced short range ordering was the origin of the in-the-film-phase anisotropy observed in amorphous film deposited in the presence of a magnetic field. The formation mechanism was different from that of the short range ordering induced by field annealing. The perpendicular anisotropy was shown to be growth induced. Large in-plane anisotropy in amorphous films was resulted form partial crystallization in the film. Both the formation of growth induced structure and partial crystallization in the film prevented the formation of the pair ordering and decreased in-the-film-plane anisotropy

Copper-promoted oxidative coupling of enamides and alkynes for the synthesis of substituted pyrroles.

Science.gov (United States)

Zhao, Mi-Na; Ren, Zhi-Hui; Wang, Yao-Yu; Guan, Zheng-Hui

2014-02-10

An efficient copper-promoted oxidative coupling of enamides with alkynes has been developed for the synthesis of substituted pyrroles. The reaction proceeded through C-H and N-H bond functionalization of enamides under mild conditions. Copyright © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Description of spin reorientation transition in Au/Co/Au sandwich with Co film thickness within a simple phenomenological model of ferromagnetic film

International Nuclear Information System (INIS)

Popov, A.P.

2012-01-01

Simple phenomenological model of ferromagnetic film characterized by equal energies of surface anisotropies at two sides of a film (symmetric film) is considered. The model is used to describe a two-step spin reorientation transition (SRT) in Au/Co/Au sandwich with Co film thickness: the SRT from perpendicular to canted noncollinear (CNC) state at N ⊥ =6.3 atomic layers and the subsequent SRT from CNC to in-plane state at N ∥ =10.05 atomic layers. Analytic expressions for the stability criterion of collinear perpendicular and in-plane states of a film are derived with account of discrete location of atomic layers. The dependence of borders that separate regions corresponding to various magnetic states of a film in the (k B ,k S )-diagram on film thickness N is established. k S (k B ) is surface (bulk) reduced anisotropy constant. The comparison of theory with experiment related to Au/Co/Au sandwich shows that there is a whole region in the (k B ,k S )-diagram corresponding to experimentally determined values of threshold film thicknesses N ⊥ =6.3 and N ∥ =10.05. The comparison of this region with similar region determined earlier for a bare Co/Au film within the same model of asymmetric film and characterized by N ⊥ =3.5, N ∥ =5.5 shows that the intersection of these regions is not empty. Hence, both the SRT in Au/Co/Au sandwich and in bare Co/Au film with Co film thickness can be described within the same model using the same magnitudes of model parameters k S , k B . Based on this result we conclude that the energy of Neel surface anisotropy at free Co surface is negligible compared to the energy of Co–Au interface anisotropy. It is demonstrated that the destabilization of collinear states in symmetric film leads to occurrence of the ground CNC state and two novel metastable CNC states. These three CNC states exhibit different kinds of symmetry. In case of asymmetric film only ground CNC state occurs on destabilization of collinear states of a film

Macrophage activating activity of pyrrole alkaloids from Morus alba fruits.

Science.gov (United States)

Kim, Seon Beom; Chang, Bo Yoon; Jo, Yang Hee; Lee, Sang Hoon; Han, Sang-Bae; Hwang, Bang Yeon; Kim, Sung Yeon; Lee, Mi Kyeong

2013-01-09

The fruits of Morus alba have been traditionally used as a tonic to enhance immune responses. The macrophage activating constituents of Morus alba fruits were purified using various column chromatography techniques. The structures of isolated compounds were determined on the basis of spectroscopic data interpretation such as 1D and 2D NMR analysis. The macrophage activating activities of isolated compounds were evaluated by measuring the production of nitric oxide, TNF-α and IL-12 in RAW 264.7 cells. The phagocytic activity was also evaluated. Five pyrrole alkaloids, 5-(hydroxymethyl)-1H-pyrrole-2-carboxaldehyde (1), 2-formyl-1H-pyrrole-1-butanoic acid (2), 2-formyl-5-(hydroxymethyl)-1H-pyrrole-1-butanoic acid (3), 2-formyl-5-(methoxymethyl)-1H-pyrrole-1-butanoic acid (4) and Morrole A (5) were isolated from the fruits of Morus alba. Morrole A (5) is first reported in nature and other pyrrole alkaloids (1-4) are first reported from Morus species. Among the isolated compounds, compounds 3 and 4 significantly activated macrophage activity by the enhancement of nitric oxide, TNF-α and IL-12 production, and the stimulation of phagocytic activity in RAW 264.7 cells. Pyrrole alkaloids, including a new compound, were isolated from Morus alba fruits. These compounds activated macrophage activity in RAW 264.7 cells. Copyright © 2012 Elsevier Ireland Ltd. All rights reserved.

Magnetic anisotropies and magnetic switching in Co films

Science.gov (United States)

Bland, J. A. C.; Baird, M. J.; Leung, H. T.; Ives, A. J. R.; Mackay, K. D.; Hughes, H. P.

1992-07-01

We have used the magneto-optical Kerr effect to investigate the role of the substrate and growth conditions in determining the magnetic switching behaviour of Co films in the thickness range 100-200 Å supported by GaAs(001) and Si(111) substrates. We discuss the anisotropic magnetic hysteresis behaviour observed for Co/GaAs and Co/Si films in terms of coherent rotation of the magnetisation vector during magnetic switching. Equivalent films supported by glass substrates are found to be almost isotropic in-plane. The in-plane coercive and saturation fields are observed to lie in the range 20-80 Oe but perpendicular saturation fields of 25 and 19 kOe are found for the Co/Si and Co/GaAs systems respectively which substantially exceed the demagnetising field in each case. The measured perpendicular anisotropy fields differ strongly from the values for hcp and bcc Co and are attributed to the details of the interface and film structure. We also report strongly frequency dependent magnetic switching behaviour in these Co films.

Sequential sputtered Co-HfO{sub 2} granular films

Energy Technology Data Exchange (ETDEWEB)

Chadha, M.; Ng, V.

2017-03-15

A systematic study of magnetic, magneto-transport and micro-structural properties of Co-HfO{sub 2} granular films fabricated by sequential sputtering is presented. We demonstrate reduction in ferromagnetic-oxide formation by using HfO{sub 2} as the insulting matrix. Microstructure evaluation of the films showed that the film structure consisted of discrete hcp-Co grains embedded in HfO{sub 2} matrix. Films with varying compositions were prepared and their macroscopic properties were studied. We correlate the variation in these properties to the variation in film microstructure. Our study shows that Co-HfO{sub 2} films with reduced cobalt oxide and varying properties can be prepared using sequential sputtering technique. - Highlights: • Co-HfO{sub 2} granular films were prepared using sequential sputtering. • A reduction in ferromagnetic-oxide formation is observed. • Co-HfO{sub 2} films display superparamagnetism and tunnelling magneto-resistance. • Varying macroscopic properties were achieved by changing film composition. • Applications can be found in moderate MR sensors and high –frequency RF devices.

Self-Aggregation in Pyrrole:  Matrix Isolation, Solid State Infrared Spectroscopy, and DFT Study

OpenAIRE

Gómez-Zavaglia, Andrea; Fausto, Rui

2004-01-01

Pyrrole (C4H5N) was embedded in low-temperature solid inert matrixes (argon, xenon; T = 9 K) and both the monomer and low-order aggregates characterized by FTIR spectroscopy. The spectroscopic studies were complemented by extensive theoretical [DFT(B3LYP)/6-311++G(d,p)] structural and vibrational studies carried out for the monomer and their self-aggregates (up to four units). The calculated spectrum for monomeric pyrrole fits well those obtained immediately after deposition (at 9 K) of dilut...

P(o-chlorophenol–co-o-hydroxyphenol: kinetic formation studies and pH-sensor application

Directory of Open Access Journals (Sweden)

Said M. Sayyah

2017-03-01

Full Text Available Electrochemical copolymerization of o-chlorophenol (o-ClPh with o-hydroxyphenol (o-HOPh was conducted in aqueous H2SO4 using cyclic voltammetry technique at the Pt electrode. The reaction rate was found to be of the second order in the monomer concentration and first order in the acid concentration. The activation energy, enthalpy, and entropy for the copolymerization were found to be 20.20 kJ mol-1, 19.24 kJ mol-1 and -281.47 J K-1 mol-1, respectively. The obtained copolymer films show smooth feature with amorphous nature. Copolymer films adhere Pt electrode very well and show less reactivity in the H2SO4 medium. The pH sensitivity of the poly(oClPh-co-HOPh-modified electrode has been investigated potentiometrically using different polymer thicknesses. The potentiometric responses to pH change of the poly(oClPh-co-HOPh-modified electrode appeared reversible and linear in the range from pH 2-11 with a maximum sub-Nernstian potentiometric response slope of 40.7 mV/pH (30 °C. The slope became close to 56.2 mV/pH in the range from pH 4 to 9 at (30 °C. The poly(oClPh-co-HOPh-modified electrode readily responded to pH change but was not stable with time.

Oxidative coupling and polymerization of pyrroles

International Nuclear Information System (INIS)

Hansen, Gregers Hendrik; Henriksen, Rikke Morck; Kamounah, Fadhil S.; Lund, Torben; Hammerich, Ole

2005-01-01

The electrochemical oxidation of 2,4-dimethyl-3-ethylpyrrole in acetonitrile has been studied using cyclic voltammetry, constant current coulometry, preparative electrolyses and ab initio calculations. The product analysis after the preparative electrolyses was carried out by HPLC combined with UV-vis and electrospray ionization MS detection. The aim of the work was to address some of the unresolved problems in the oxidative oligomerization and polymerization of alkylpyrroles. The title compound was chosen as a model for studies of pyrroles that are more basic than the solvent-supporting electrolyte system and for that reason are forced to serve as the base accepting the protons released during the coupling steps. The voltammograms obtained by cyclic voltammetry at a substrate concentration of 2 mM and voltage scan rates between 0.02 and 2 V s -1 showed a characteristic trace-crossing phenomenon that could be demonstrated by digital simulation to be related to that fact that the deprotonations of the initially formed dimer dication are slow with second order rate constants in the range 10 3 -10 4 M -1 s -1 . The relative stability of the different tautomers of the protonated pyrrole monomer and the corresponding 2,2'-dimer was determined by ab initio calculations at the RHF 6-31G(d) level. The studies also included investigations of the effects resulting from addition of a non-nucleophilic base, 2,6-di-tert-butylpyridine, to the voltammetry solutions. The major product observed after preparative electrolyses was a trimer the structure of which is proposed to include a central 2H-pyrrole unit. Since 2H-pyrroles are stronger bases than the corresponding 1H-pyrroles, the trimer is effectively protected against further oxidation by protonation. Two other trimers were observed as minor or trace products as well as a 1H,2H-dimer and several tetramers, also in trace amounts. In addition to the dimer, the trimers and the tetramers, a number of other minor products could be

Applications of Poly(indole-6-carboxylic acid-co-2,2′-bithiophene Films in High-Contrast Electrochromic Devices

Directory of Open Access Journals (Sweden)

Chung-Wen Kuo

2018-03-01

Full Text Available Two homopolymers (poly(indole-6-carboxylic acid (PInc and poly(2,2′-bithiophene (PbT and a copolymer (poly(indole-6-carboxylic acid-co-2,2′-bithiophene (P(Inc-co-bT are electrodeposited on ITO electrode surfaces via electrochemical method. Electrochemical and electrochromic properties of PInc, PbT, and P(Inc-co-bT films were characterized using cyclic voltammetry and in situ UV-Vis spectroscopy. The anodic P(Inc-co-bT film prepared using Inc./bT = 1/1 feed molar ratio shows high optical contrast (30% at 890 nm and coloring efficiency (112 cm2 C−1 at 890 nm. P(Inc-co-bT film revealed light yellow, yellowish green, and bluish grey in the neutral, intermediate, and oxidation states, respectively. Electrochromic devices (ECDs were constructed using PInc, PbT, or P(Inc-co-bT film as anodic layer and PEDOT-PSS as cathodic layer. P(Inc-co-bT/PMMA-PC-ACN-LiClO4/PEDOT-PSS ECD showed high ∆T (31% at 650 nm, and PInc/PMMA-PC-ACN-LiClO4/PEDOT-PSS ECD displayed high coloration efficiency (416.7 cm2 C−1 at 650 nm. The optical memory investigations of PInc/PMMA-PC-ACN-LiClO4/PEDOT-PSS, PbT/PMMA-PC-ACN-LiClO4/PEDOT-PSS, and P(Inc-co-bT/PMMA-PC-ACN-LiClO4/PEDOT-PSS ECDs exhibited that ECDs had adequate optical memory in bleaching and coloring states.

Preparation and characterization of electrodeposited ZnO and ZnO:Co nanorod films for heterojunction diode applications

Energy Technology Data Exchange (ETDEWEB)

Caglar, Yasemin, E-mail: yasemincaglar@anadolu.edu.tr [Anadolu University, Science Faculty, Physics Department, Eskisehir (Turkey); Arslan, Andaç [Eskisehir Osmangazi University, Art and Science Faculty, Chemistry Department, Eskisehir (Turkey); Ilican, Saliha [Anadolu University, Science Faculty, Physics Department, Eskisehir (Turkey); Hür, Evrim [Eskisehir Osmangazi University, Art and Science Faculty, Chemistry Department, Eskisehir (Turkey); Aksoy, Seval; Caglar, Mujdat [Anadolu University, Science Faculty, Physics Department, Eskisehir (Turkey)

2013-10-15

Highlights: •Undoped and Co-doped ZnO films were deposited on p-Si by electrodeposition method. •The effects of Co doping on some properties of ZnO films were investigated. •ZnO morphology was converted uniform multi-oriented rods with incorporation of Co. •Co-doped ZnO nanorod films showed a multi-oriented spear-like structure. -- Abstract: Well-aligned undoped and Co-doped nanorod ZnO films were grown by electrochemical deposition onto p-Si substrates from an aqueous route. Aqueous solution of Zn(NO{sub 3}){sub 2}⋅6H{sub 2}O and hexamethylenetetramine (HMT) were prepared using triple distilled water. Two different atomic ratios of Co(NO{sub 3}){sub 2}⋅6H{sub 2}O were used as a dopant element. Electrodepositions were carried out in a conventional three electrode cell for the working electrode (p-Si), reference electrode (Ag/AgCl, sat.) and counter electrode (platin wire). The effects of Co doping on the structural, morphological and electrical properties of ZnO films were investigated. X-ray diffraction (XRD) measurement showed that the undoped ZnO nanorod film was crystallized in the hexagonal wurtzite phase and presented a preferential orientation along the c-axis. Only one peak, corresponding to the (0 0 2) phase, appeared on the diffractograms. The lattice parameters and texture coefficient values were calculated. The nanorods were confirmed by the field emission scanning electron microscopy (FE-SEM) measurements. The FE-SEM image showed that the ZnO nanorods grow uniformly on the substrates, providing a surface with fairly homogeneous roughness. The surface morphology was transformed into uniform multi-oriented rods with incorporation of Co. Co-doped ZnO nanorod films showed a multi-oriented spear-like structure. The diffuse reflectance spectra of the films were measured and the optical band gap values were determined using Kubelka–Munk theory. The van der Pauw method was used to measure the sheet resistance of the films. The sheet resistance

Pyrrole-regulated precipitation of titania nanorods on polymer fabrics for photocatalytic degradation of trace toluene in air

Science.gov (United States)

Gu, Yi-Jie; Wen, Wei; Xu, Yang; Wu, Jin-Ming

2018-03-01

When compared with nanoparticulate counterparts, TiO2 thin films with vertically aligned one-dimensional (1D) nanostructures exhibit enhanced photocatalytic activity because of the highly accessible surface area. The perpendicular of the 1D nanostructure reduces the charge migration path and hence the carrier recombination rate, which also contributes to the photocatalytic activity. Furthermore, TiO2 thin films on flexible substrates are more suitable to degrade pollutants in either water or air because of its easy recovery and free-bending shape. In this study, flexible polyethylene fabrics were firstly coated with a sol-gel nanoparticulate TiO2 seed layer. Quasi-aligned TiO2 nanorods were then precipitated homogeneously under an atmospheric pressure and a low temperature not exceeding 80 °C, using a peroxy-titanium complex precursor with the additive of pyrrole. It is found that the density of TiO2 nanorods increased with the increasing amount of pyrrole monomers. The resultant TiO2 film on polyethylene fabrics exhibited a much reduced band gap of ca. 2.86 eV, which can be attributed to the surface oxygen deficiencies. When utilized to assist photocatalytic degradation of trace toluene in air under the UV light illumination, the TiO2 film exhibited a gradually increased photocatalytic activity upon the increasing cycles for up to six, because of the gradual removal of trace organics on the TiO2 surface. The highest photocatalytic efficiency is recorded to be 5 times that of TiO2 nanotube arrays, which are regarded as an excellent photocatalyst for air cleaning.

Stability of CoP x Electrocatalysts in Continuous and Interrupted Acidic Electrolysis of Water.

Science.gov (United States)

Goryachev, Andrey; Gao, Lu; Zhang, Yue; Rohling, Roderigh Y; Vervuurt, René H J; Bol, Ageeth A; Hofmann, Jan P; Hensen, Emiel J M

2018-04-11

Cobalt phosphides are an emerging earth-abundant alternative to platinum-group-metal-based electrocatalysts for the hydrogen evolution reaction (HER). Yet, their stability is inferior to platinum and compromises the large-scale applicability of CoP x in water electrolyzers. In the present study, we employed flat, thin CoP x electrodes prepared through the thermal phosphidation (PH 3 ) of Co 3 O 4 films made by plasma-enhanced atomic layer deposition to evaluate their stability in acidic water electrolysis by using a multi-technique approach. The films were found to be composed of two phases: CoP in the bulk and a P-rich surface CoP x (P/Co>1). Their performance was evaluated in the HER and the exchange current density was determined to be j 0 =-8.9 ⋅ 10 -5  A/cm 2 . The apparent activation energy of HER on CoP x ( E a =81±15 kJ/mol) was determined for the first time. Dissolution of the material in 0.5 M H 2 SO 4 was observed, regardless of the constantly applied cathodic potential, pointing towards a chemical instead of an electrochemical origin of the observed cathodic instability. The current density and HER faradaic efficiency (FE) were found to be stable during chronoamperometric treatment, as the chemical composition of the HER-active phase remained unchanged. On the contrary, a dynamic potential change performed in a repeated way facilitated dissolution of the film, yielding its complete degradation within 5 h. There, the FE was also found to be changing. An oxidative route of CoP x dissolution has also been proposed.

Synthesis of 14C analogue of 1,2-diaryl-[2-14C]-pyrroles

International Nuclear Information System (INIS)

Saemian, N.; Shirvani, G.; Matloubi, H.

2007-01-01

Three 1,2-diaryl pyrroles selective COX-2 inhibitors, 2-(4-fluorophenyl)-5-methyl-1-(4-methylsulfonyl-phenyl)-1H pyrrole, 2-(4-fluorophenyl)-1- [4-(methylsulfonyl) phenyl]-1H-pyrrole and 4-[2-(4-fluorophenyl)-1H-pyrrol-1-yl]benzenesulfon-amide, all three labeled with 14 C in the 2-position were prepared from para-fluoro-benzaldehyde-[carbonyl- 14 C]. (author)

Photochemical deposition of NiCoO x thin films from Ni/Co heteronuclear triketonate complexes

International Nuclear Information System (INIS)

Buono-Core, G.E.; Tejos, M.; Cabello, G.; Guzman, N.; Hill, R.H.

2006-01-01

UV light irradiation of thin films of a polyketonate Ni/Co heteronuclear complex, NiCo(DBA) 2 [DBA, dibenzoylacetone)], spin coated on Si(1 0 0) substrates produced NiCoO x mixed oxides as amorphous films. On annealing at 600 deg. C under air, the mixed oxide film decomposed to NiO and CoO as indicated by XRD measurements. The morphology of the as-deposited films was examined by AFM analysis showing a smooth surface with low rms roughness values. The ratio of Ni/Co (1.08) present in the film reflects the stoichiometry in the starting compound within the experimental error, as shown by XPS analysis. The large amount of carbon (20.8%) detected on the surface of the film may be due to the presence of phenyl rings in the precursor complex

A New Biomarker Proxy for Palaeo-pCO2 Reconstruction in Ancient Sediments

Science.gov (United States)

Pancost, R. D.; Magness, S.; Maxwell, J. R.

2001-12-01

The carbon isotopic composition of marine organic matter has commonly been used in chemostratigraphy or as a proxy for ancient pCO2 levels. Both of these goals require that the source of organic matter be well defined, and in the case of palaeo-pCO2 investigations, the organic matter must be derived ultimately from aquatic photoautotrophs. However, additional sources, including terrestrial biomass, heterotrophs, or bacteria, can also contribute to total organic carbon (TOC). In the past decade, numerous workers have attempted to refine organic carbon isotope records using the isotopic composition of individual compounds (biomarkers) rather than the TOC. The appeal of this approach is that by examining specific biomarkers, a signal diagnostic for photoautotrophic organisms can be obtained. For compound-specific isotope analyses to be most effective, the compounds analysed must have a relatively specific source. Among the most commonly used biomarkers in palaeo-pCO2 investigations are alkenones, long-chain ketones derived exclusively from certain species of haptophyte algae. However, alkenones are absent in rocks older than the Jurassic and either absent or present in low abundances in rocks older than the Miocene. Thus, in older rocks, other biomarkers, including steranes (derived from eukaryotic sterols), phytane (presumably derived from chlorophyll), and n-alkanes (derived from algal macromolecules), are used. Unfortunately, these compounds can have alternative sources and become less reliable as isotopic proxies for photoautotrophs with increasing thermal maturity and complexity of the hydrocarbon distribution. Here we propose the use of a maleimides (1H-pyrrole-2,5-diones) as a new biomarker class for evaluating past changes in photoautotroph carbon isotopic compositions. Maleimides have three key advantages over other biomarkers in ancient rocks. First, they are degradation products of chlorophyll and have no known alternative origins in marine sediments

Ethyl 5-cyano-4-[2-(2,4-dichlorophenoxyacetamido]-1-phenyl-1H-pyrrole-3-carboxylate

Directory of Open Access Journals (Sweden)

Jing Xu

2009-08-01

Full Text Available In the title compound, C22H17Cl2N3O4, the pyrrole ring and the 2,4-dichlorophenyl group form a dihedral angle of 8.14 (13°; the phenyl ring is twisted with respect to the pyrrole ring, forming a dihedral angle of 60.77 (14°. The C=O bond length is 1.213 (3 Å, indicating that the molecule is in the keto form, associated with a –CONH– group, and the amide group adopts the usual trans conformation. The molecule is stabilized by an intramolecular N—H...O hydrogen-bonding interaction. In the crystal, the stacked molecules exhibit intermolecular C—H...O and C—H...N hydrogen-bonding interactions.

Morphological and physicochemical properties of dip-coated poly {(2,5-diyl pyrrole) [4-nitrobenzylidène]} (PPNB) thin films: towards photovoltaic applications

Science.gov (United States)

Mouchaal, Younes; Gherrass, Hamou; Bendoukha Reguig, Abdelkarim; Hachemaoui, Aïcha; Yahiaoui, Ahmed; Makha, Mohamed; Khelil, Abdelbacet; Bernede, Jean-Christian

2015-02-01

A new material: conjugated poly {(2,5-diyl pyrrole) [4-nitrobenzylidène]}, that we called (PPNB), has been synthesized and characterized. The cyclic voltammetry has been used in order to estimate first oxidation (Ep) and reduction (En) potentials of our polymer. These values have been assigned, respectively, to the position of the highest occupied molecular orbital (HOMO) and the lowest unoccupied molecular orbital (LUMO) and determination of the energy band gap which have been estimated to be 6.16, 3.89 and 2.27 eV respectively. Energy levels values of the HOMO and LUMO of the PPNB polymeric donor material were evaluated and the results are compatible with an electron transfer to C60 within an eventual junction, such values show that PPNB could be probed for applications in organic solar cells as donor material. PPNB Thin films have been deposited by dip-coating technique from Dichloromethane solvent with different polymer concentrations, and a dipping speed of 3.0 cm/min. For morphological characterization of the films scanning electron microscopy (SEM) was carried out. The samples, when observed by SEM, reveals that the films deposited are less dense, uniform. Cross-sectional SEM micrographs PPNB films show that thickness of the layers is homogeneous and has value of 35-40 nm. Optical characteristics of the polymer thin films were studied using UV-vis spectroscopy; absorption of wide range of wavelengths from 350 to 700 nm was observed. The optical band gap energy ranges between 1.9 eV and 1.94 eV. Based on these analyzes we realized heterojunction organic solar cells with the structure: ITO/Au/PPNB/C60/BCP/Al, the cells had a photovoltaique effect after J-V measuring, however the efficiency of photo generation under AM1.5 illumination was weak (about 0.02%) and needs to be improved.

Synthesis and characterisation of new Schiff base monomers containing N-(alkyl and phenyl) pyrrole moieties

Science.gov (United States)

Amer, Ahcene Ait; Ilikti, Hocine; Maschke, Ulrich

2017-11-01

This article deals with the synthesis and characterisation of seven new functional Schiff base monomers, such as: M1: 1-(3-Pyrrole-1-yl-propylimino-methyl)-naphtalen-2-ol; M2: 2-(3-Pyrrole-1-yl-phenylimino-methyl)-phenol; M3: 1-(3-Pyrrole-1-yl-phenylimino-methyl)-naphtalen-2-ol; M4: N-(pyridin-2-yl-methylene)-2-(pyrrol-1-yl)-benzenamine; M5: N-(pyridin-2-yl-methylene)-3-(pyrrol-1-yl)-propan-1-amine; M6: 2-(3-pyrrol-1-yl-propylimino-methyl)-quinolin-8-ol; M7: 2-(3-pyrrol-1-yl-phenylimino-methyl)-quinolin-8-ol. Two series of compounds emerged from this study, N-propyl pyrrole derivatives (M1, M5, M6) and N-phenyl pyrrole compounds (M2, M3, M4, M7). All monomers were elaborated by condensation reactions between appropriate amines and aldehydes, and their molecular structures were confirmed by spectroscopic analysis methods like FT-IR, 1H NMR, 13C NMR, and GC-MS.

Growth and structure of Co/Au magnetic thin films

International Nuclear Information System (INIS)

Marsot, N.

1999-01-01

We have studied the growth and the crystallographic structure of magnetic ultra thin cobalt/gold films (Co/Au), in order to investigate the correlations between their magnetic and structural properties. Room temperature (R.T.) Co growth on Au (111) proceeds in three stages. Up to 2 Co monolayers (ML), a bilayer island growth mode is observed. Between 2 and 5 ML, coalescence of the islands occurs, covering the substrate surface and a Co/Au mixing is observed resulting from the de-construction of the Herringbone reconstruction. Finally, beyond 5 ML, the CoAu mixing is buried and the Co growth continues in a 3-D growth. Annealing studies at 600 K on this system show a smoothing effect of the Co film, and at the same time, segregation of Au atoms. The quality of the Co/Au interface (sharpness) is not enhanced by the annealing. The local order was studied by SEXAFS and the long range order by GIXRD showing that the Co film has a hexagonal close packed structure, with an easy magnetization axis perpendicular to the surface. From a local order point of view, the Co grows with an incoherent epitaxy and keeps its own bulk parameters. The GIXRD analysis shows a residual strain in the Co film of 4%. The difference observed between the local order analysis and the long range order results is explained in terms of the low dimensions of the diffracting domains. The evolution of film strains, as a function of the Co coverage, shows a marked deviation from the elastic strain theory. Modification of the strain field in the Co film as a function of the Au coverage is studied by GIXRD analysis. The Au growth study, at R.T., shows no evidence of a Au/Co mixing in the case of the Au/Co interface. The Au overlayer adopts a twinned face centred cubic structure on the rough Co film surface. (author)

Electrodeposition and characterization of nanocrystalline CoNiFe films

Energy Technology Data Exchange (ETDEWEB)

Chen, Y.; Wang, Q.P. [Department of Chemistry, Zhejiang University, Hangzhou, Zhejiang 310027 (China); Cai, C. [School of Chemistry and chemical engineering, Ningxia University, Yinchuan 750021 (China); Yuan, Y.N. [Department of Materials and Chemistry, Zhejiang University, Hangzhou, Zhejiang 310027 (China); Cao, F.H. [Department of Chemistry, Zhejiang University, Hangzhou, Zhejiang 310027 (China); Zhang, Z., E-mail: eaglezzy@zjuem.zju.edu.cn [Department of Chemistry, Zhejiang University, Hangzhou, Zhejiang 310027 (China); Zhang, J.Q. [Department of Chemistry, Zhejiang University, Hangzhou, Zhejiang 310027 (China); State Key Laboratory for Corrosion and Protection of Metals, Shenyang 110016 (China)

2012-02-29

Nanocrystalline Co{sub 45}Ni{sub 10}Fe{sub 24} films have been fabricated using cyclic voltammetry technique from the solutions containing sulfate, then characterized by scanning electron microscopy, X-ray diffraction and vibrating sample magnetometer. Meanwhile, Electrochemical Impedance Spectroscopy technique has been employed to probe into the nucleation/growth behavior of Co{sub 45}Ni{sub 10}Fe{sub 24} films. The results show that, the obtained Co{sub 45}Ni{sub 10}Fe{sub 24} film possesses low coercivity of 973.3 A/m and high saturation magnetic flux density of 1.59 Multiplication-Sign 10{sup 5} A/m. Under the experimental conditions, the nucleation/growth process of Co{sub 45}Ni{sub 10}Fe{sub 24} films is mainly under activation control. With the increase of the applied cathodic potential bias, the charge transfer resistance for CoNiFe deposition decreases exponentially. - Highlights: Black-Right-Pointing-Pointer Nanocrystalline Co{sub 45}Ni{sub 10}Fe{sub 24} film is obtained using cyclic voltammetry technique. Black-Right-Pointing-Pointer Nanocrystalline Co{sub 45}Ni{sub 10}Fe{sub 24} possesses low coercivity of 973.3 A/m. Black-Right-Pointing-Pointer Nanocrystalline Co{sub 45}Ni{sub 10}Fe{sub 24} possesses high saturation magnetic flux density. Black-Right-Pointing-Pointer The nucleation/growth process of CoNiFe films is mainly under activation control. Black-Right-Pointing-Pointer The charge transfer resistance for CoNiFe deposition decreases exponentially.

Partnervalg på film

DEFF Research Database (Denmark)

Kramer, Mette

2006-01-01

Nye kognitions- og evolutionspsykologiske aspekter på kvinders filmpræferencer for romantiske film og melodramer......Nye kognitions- og evolutionspsykologiske aspekter på kvinders filmpræferencer for romantiske film og melodramer...

Hydrolytic study of the copolymer Poly pyrrole/ Polyethyleneglycol and Poly pyrrole synthesized by plasma

International Nuclear Information System (INIS)

Colin, E.; Enriquez, M.A.; Olayo, M.G.; Cruz, G.J.; Carapia, L.; Romero, M.; Morales, J.; Olayo, R.

2006-01-01

In this work the study about the hydrolytic compatibility of semiconductor polymers, copolymer Poly pyrrole/ Polyethyleneglycol (PPy/PEG) and Poly pyrrole (PPy) for their possible use as biomaterials. The polymers were synthesized by plasma between 10 and 100 W, with discharges of splendor RF to 13.5 MHz with resistive coupling. The hydrolytic affinity was evaluated calculating the contact angle with solutions of NaCl, NaCl-MgSO 4 and Krebs-Ringer. The results show a hydrophilicity increment due to the increase of the surface ruggedness with the synthesis energy. On the contrary, the crystallinity diminishes when increasing the power in PPy and it stays approximately constant in PPy/PEG. The electric conductivity presents a growth from 2 to 4 magnitude orders in function of the water content in the polymers. (Author)

Dual pO2/pCO2 fibre optic sensing film.

Science.gov (United States)

Davenport, John J; Hickey, Michelle; Phillips, Justin P; Kyriacou, Panayiotis A

2017-05-15

A fibre optic multi-sensor has been developed for biomedical sensing applications using a tip coating solution sensitive to both oxygen and carbon dioxide. An oxygen sensitive phosphorescence quenching complex based on platinum octaethylporphyrin (PtOEP) was combined with a carbon dioxide sensitive phosphorescence compound based on 8-hydroxypyrene-1,3,6-trisulfonic acid trisodium salt (HPTS). When excited by blue light (470 nm), the resultant coating had two fluorescent peaks at 515 nm (green) and 645 nm (red) which responded to partial pressure of CO 2 and O 2 respectively. The sensor was tested in vitro and shown to be able to measure CO 2 and O 2 simultaneously and in real time, with calibration constants of 0.0384 kPa -1 and 0.309 kPa -1 respectively. The O 2 sensitive peak received some overlap from the 515 nm peak (0.38% of peak intensity) as well as some cross-sensitivity (maximum, 5.1 kPa pCO 2 gave a measurement equivalent to 0.43 kPa of O 2 , a ratio of 0.08 : 1). However, these effects can be subtracted from measurements and no significant cross-sensitivity or overlap was seen in CO 2 measurements from O 2 . This novel compound presents great potential for use in medical sensors and we expect it to be important to a wide range of future applications.

Role of the ribose-specific marker furfuryl-amine in the formation of aroma active 1-(furan-2-ylmethyl)-1H-pyrrole (or furfuryl-pyrrole) derivatives.

Science.gov (United States)

Nikolov, Plamen Y; Yaylayan, Varoujan A

2012-10-10

Furfuryl-pyrroles possess a diverse range of organoleptic properties described as roasted, chocolaty, green, horseradish-like, and mushroom-like and are detected in various foods such as coffee, chocolate, popcorn, and roasted chicken. Although their origin in food was attributed to furfuryl-amine, the latter has not been detected so far in Maillard model systems or in foods. In this study, furfuryl-amine was shown to be formed specifically from ribose through nitrogen atom transfer from the α-amino group of any amino acid. Such a transfer can be achieved through decarboxylation of the Schiff base adduct and isomerization followed by hydrolysis. Through the use of (15)Nα-lysine it was revealed that only the (15)Nα nitrogen atom was incorporated into its structure, indicating a specific role for the carboxylate moiety in the mechanism of its formation. Furthermore, isotope labeling studies have indicated that furfuryl-pyrrole derivatives can be formed by the interaction of 2 mol of furfuryl-amine with 3-deoxyribosone followed by dehydration and cyclization to form 1-(furan-2-yl)-N-{[1-(furan-2-ylmethyl)-1H-pyrrol-2-yl]methylidene}methanamine. After hydrolysis, this intermediate can generate furfuryl-formyl-pyrrole, furfuryl-pyrrole carboxylic acid, and furfuryl-pyrrole. In this study, the furfuryl-amine derivatives were also detected in different coffee beans after pyrolysis and analysis by GC-MS. The potential of these compounds to form in aqueous model systems at a temperature of 120 °C was also demonstrated.

Surface composition of magnetron sputtered Pt-Co thin film catalyst for proton exchange membrane fuel cells

Energy Technology Data Exchange (ETDEWEB)

Vorokhta, Mykhailo, E-mail: vorohtam@gmail.com [Charles University in Prague, Faculty of Mathematics and Physics, Department of Surface and Plasma Science, V Holešovičkách 2, 18000 Prague (Czech Republic); Khalakhan, Ivan; Václavů, Michal [Charles University in Prague, Faculty of Mathematics and Physics, Department of Surface and Plasma Science, V Holešovičkách 2, 18000 Prague (Czech Republic); Kovács, Gábor; Kozlov, Sergey M. [Departament de Química Física and Institut de Química Teòrica i Computacional (IQTCUB), Universitat de Barcelona, c/ Martí i Franquès 1, 08028 Barcelona (Spain); Kúš, Peter; Skála, Tomáš; Tsud, Natalia; Lavková, Jaroslava [Charles University in Prague, Faculty of Mathematics and Physics, Department of Surface and Plasma Science, V Holešovičkách 2, 18000 Prague (Czech Republic); Potin, Valerie [Laboratoire Interdisciplinaire Carnot de Bourgogne, UMR 6303 CNRS-Université Bourgogne, 9 Av. A. Savary, BP 47870, F-21078 Dijon Cedex (France); and others

2016-03-01

Graphical abstract: - Highlights: • Nanostructured Pt-Co thin catalyst films were grown on carbon by magnetron sputtering. • The surface composition of the nanostructured Pt-Co films was investigated by surface analysis techniques. • We carried out modeling of Pt-Co nanoalloys by computational methods. • Both experiment and modeling based on density functional theory showed that the surface of Pt-Co nanoparticles is almost exclusively composed of Pt atoms. - Abstract: Recently we have tested a magnetron sputtered Pt-Co catalyst in a hydrogen-fed proton exchange membrane fuel cell and showed its high catalytic activity for the oxygen reduction reaction. Here we present further investigation of the magnetron sputtered Pt-Co thin film catalyst by both experimental and theoretical methods. Scanning electron microscopy and transmission electron microscopy experiments confirmed the nanostructured character of the catalyst. The surface composition of as-deposited and annealed at 773 K Pt-Co films was investigated by surface analysis techniques, such as synchrotron radiation photoelectron spectroscopy and X-ray photoelectron spectroscopy. Modeling based on density functional theory showed that the surface of 6 nm large 1:1 Pt-Co nanoparticles is almost exclusively composed of Pt atoms (>90%) at typical operation conditions and the Co content does not exceed 20% at 773 K, in agreement with the experimental characterization of such films annealed in vacuum. According to experiment, the density of valence states of surface atoms in Pt-Co nanostructures is shifted by 0.3 eV to higher energies, which can be associated with their higher activity in the oxygen reduction reaction. The changes in electronic structure caused by alloying are also reflected in the measured Pt 4f, Co 3p and Co 2p photoelectron peak binding energies.

Dual Stimuli-Responsive P(NIPAAm-co-SPA Copolymers: Synthesis and Response in Solution and in Films

Directory of Open Access Journals (Sweden)

Oliver Grimm

2018-06-01

Full Text Available We present the synthesis and solution properties of dual stimuli-responsive poly(N-isopropylacrylamide-co-spiropyran acrylate (P(NIPAAm-co-SPA copolymers of varying composition prepared via nitroxide-mediated copolymerization. The resulting copolymers feature molar masses from 40,000 to 100,000 g/mol according to static light scattering and an SPA content of up to 5.3%. The latter was determined by 1H NMR spectroscopy and UV–Vis spectroscopy. These materials exhibit reversible response upon irradiation in polymeric films for a minimum of three cycles; their response in solution to both light and temperature was also investigated in an aqueous TRIS buffer (pH 8. Irradiation was carried out using LED setups with wavelengths of 365 and 590 nm. In aqueous solution, a custom-made setup using a fiber-coupled 200 W Hg(Xe lamp with 340 and 540 nm filters was used and additional heating of the copolymer solutions during irradiation allowed to study influence of the presence of either the spiropyran or merocyanine form on the cloud point temperature. Hereby, it was found that increasing the SPA content leads to a more pronounced difference between both states and decreasing cloud points in general.

Influence of Methacrylic-Acrylic Copolymer Composition on Plasticiser-free Optode Films for pH Sensors

Directory of Open Access Journals (Sweden)

Musa Ahmad

2003-03-01

Full Text Available In this work we have examined the use of plasticiser-free polymeric films incorporating a proton selective chromoionophore for optical pH sensor. Four types of methacrylic-acrylic copolymers containing different compositions of n-butyl acrylate (nBA and methyl methacrylate (MMA were synthesised for use as optical sensor films. The copolymers were mixed with appropriate amounts of chromoionophore (ETH5294 and a lipophilic salt before spin coated on glass slides to form films for the evaluation of pH response using spectrophotometry. Co-polymer films with high nBA content gave good response and the response time depended on the film thickness. A preliminary evaluation of the optical films of high nBA content with pHs from 2 - 14 showed distinguishable responses from pH 5 - 9. However, the adhesion of the pH sensitive film was good for copolymers with higher content of MMA but not for films with high nBA.

Stress impedance effects in flexible amorphous FeCoSiB magnetoelastic films

International Nuclear Information System (INIS)

Zhang Wanli; Peng Bin; Su Ding; Tang Rujun; Jiang Hongchuan

2008-01-01

Amorphous FeCoSiB films were deposited on the flexible polyimide substrates (Kapton type (VN)) by DC magnetron sputtering. Stress impedance (SI) effects of the flexible amorphous FeCoSiB magnetoelastic films were investigated in details. The results show that a large stress impedance effect can be observed in the flexible amorphous FeCoSiB magnetoelastic films. And the results also show a bias magnetic field plays an important role in the stress impedance of FeCoSiB films. Applied a bias magnetic field during depositing can induce obvious in-plane anisotropy in the FeCoSiB films, and a larger SI effect can be obtained with a stronger anisotropy in FeCoSiB films. Argon pressure has a significant effect on the SI effect of the FeCoSiB films. The SI of the FeCoSiB films reaches a maximum of 7.6% at argon pressure of 1.5 Pa, which can be explained by the change of residual stress in FeCoSiB films

Synthesis, vapor growth, polymerization, and characterization of thin films of novel diacetylene derivatives of pyrrole. The use of computer modeling to predict chemical and optical properties of these diacetylenes and poly(diacetylenes)

Science.gov (United States)

Paley, M. S.; Frazier, D. O.; Abeledeyem, H.; Mcmanus, S. P.; Zutaut, S. E.

1992-01-01

In the present work two diacetylene derivatives of pyrrole which are predicted by semiempirical AM1 calculations to have very different properties, are synthesized; the polymerizability of these diacetylenes in the solid state is determined, and the results are compared to the computer predictions. Diacetylene 1 is novel in that the monomer is a liquid at room temperature; this may allow for the possibility of polymerization in the liquid state as well as the solid state. Thin poly(diacetylene) films are obtained from compound 1 by growing films of the monomer using vapor deposition and polymerizing with UV light; these films are then characterized. Interestingly, while the poly(diacetylene) from 1 does not possess good nonlinear optical properties, the monomer exhibits very good third-order effects (phase conjugation) in solution. Dilute acetone solutions of the monomer 1 give intensity-dependent refractive indices on the order of 10 exp -6 esu; these are 10 exp 6 times better than for CS2.

Exchange-coupled hard magnetic Fe-Co/CoPt nanocomposite films fabricated by electro-infiltration

Directory of Open Access Journals (Sweden)

Xiao Wen

2017-05-01

Full Text Available This paper introduces a potentially scalable electro-infiltration process to produce exchange-coupled hard magnetic nanocomposite thin films. Fe-Co/CoPt nanocomposite films are fabricated by deposition of CoFe2O4 nanoparticles onto Si substrate, followed by electroplating of CoPt. Samples are subsequently annealed under H2 to reduce the CoFe2O4 to magnetically soft Fe-Co and also induce L10 ordering in the CoPt. Resultant films exhibit 0.97 T saturation magnetization, 0.70 T remanent magnetization, 127 kA/m coercivity and 21.8 kJ/m3 maximum energy density. First order reversal curve (FORC analysis and δM plot are used to prove the exchange coupling between soft and hard magnetic phases.

Underwater photosynthesis and respiration in leaves of submerged wetland plants: gas films improve CO2 and O2 exchange

DEFF Research Database (Denmark)

Colmer, Timothy David; Pedersen, Ole

2007-01-01

(N) was enhanced up to sixfold. Gas films on submerged leaves enable continued gas exchange via stomata and thus bypassing of cuticle resistance, enhancing exchange of O(2) and CO(2) with the surrounding water, and therefore underwater P(N) and respiration.......Many wetland plants have gas films on submerged leaf surfaces. We tested the hypotheses that leaf gas films enhance CO(2) uptake for net photosynthesis (P(N)) during light periods, and enhance O(2) uptake for respiration during dark periods. Leaves of four wetland species that form gas films......, and two species that do not, were used. Gas films were also experimentally removed by brushing with 0.05% (v/v) Triton X. Net O(2) production in light, or O(2) consumption in darkness, was measured at various CO(2) and O(2) concentrations. When gas films were removed, O(2) uptake in darkness was already...

Ferroelectric properties of barium strontium titanate thin films grown by RF co-sputtering

International Nuclear Information System (INIS)

Zapata-Navarro, A.; Marquez-Herrera, A.; Cruz-Jauregui, M.P.; Calzada, M.L.

2005-01-01

In this work, we present the variation of the ferroelectric properties of Ba 1-x Sr x TiO 3 films deposited on Pt/TiO 2 /SiO 2 /Si substrates by RF co-sputtering with 0≤x≤1. The co-sputtering was done using a single magnetron with BaTiO 3 /SrTiO 3 targets in a pie mosaics configuration. Smooth and uniform films were obtained using the same conditions of growth and annealing temperature. The X-ray diffraction and EDS results show that the processes were managed to obtain crystalline materials with x from 0 to 1. The behaviour of P-E loops suggests that the ferroelectric properties of the films were tuned by changing the concentration of the cation. (copyright 2005 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

One-pot Synthesis of Substituted Pyrroles with N,N,N',N'

African Journals Online (AJOL)

In this research, N,N,N'N'-tetrachlorobenzene-1,3-disulphonamide as novel catalytic reagent and N,N'-diiodo-N,N'-1,2-ethanediylbis(p-toluenesulphonamide) as new catalyst were used for the synthesis of N-substituted pyrroles in good to excellent yields under mild conditions. These reusable reagents were compared with ...

Synthesis and spectroscopic characterization of a fluorescent pyrrole derivative containing electron acceptor and donor groups

Science.gov (United States)

Almeida, A. K. A.; Monteiro, M. P.; Dias, J. M. M.; Omena, L.; da Silva, A. J. C.; Tonholo, J.; Mortimer, R. J.; Navarro, M.; Jacinto, C.; Ribeiro, A. S.; de Oliveira, I. N.

2014-07-01

The synthesis and fluorescence characterization of a new pyrrole derivative (PyPDG) containing the electron donor-acceptor dansyl substituent is reported. The effects of temperature and solvent polarity on the steady-state fluorescence of this compound are investigated. Our results show that PyPDG exhibits desirable fluorescent properties which makes it a promising candidate to be used as the photoactive material in optical thermometry and thermography applications. Further, the electrochemical and emission properties of polymeric films obtained from the oxidation polymerization of PyPDG are also analyzed.

An Efficient and Short Route for the Synthesis of Reverse Pyrrole Ribonucleosides

Directory of Open Access Journals (Sweden)

Pereira Letícia O. R.

2002-01-01

Full Text Available The synthesis of reverse pyrrole ribonucleosides methyl 5-C-(4-acetyl-5-methyl-pyrrol-1-yl-2,3-O-isopropylidene-5-deoxy- beta-D-ribofuranoside (10, methyl 5-C-(4-ethoxycarbonyl-5-methyl-pyrrol-1-yl-2,3-O-isopropylidene-5-deoxy- beta-D-ribofuranoside (11, methyl 5-C-(4-acetyl-5-methyl-pyrrol-1-yl-5-deoxy-beta-D-ribofuranoside (12, methyl 5-C-(4-ethoxycarbonyl-5-methyl-pyrrol-1-yl-5-deoxy- beta-D-ribofuranoside (13, methyl 5-deoxy-5-C-(3'-formyl-4'-hydroxypropyl-pyrrol-1'-yl-2,3-O-isopropylidene- beta-D-ribofuranoside (16 and methyl 5-deoxy-5-C-(3'-formyl-pyrrol-1'-yl-2,3-O-isopropylidene- beta-D-ribofuranoside (18 are described starting from readily available methyl 5-amino-5-deoxy-2,3-O-isopropylidene-beta-D-ribofuranoside (9. The synthetic strategy for the construction of the heterocyclic ring was based on the nucleophilic attack of (9 to 4-acetyl-2-n-butoxy-5-methyl-4,5-dihydrofuran (4, 4-carbetoxy-2-n-butoxy-5-methyl-4,5-dihydrofuran (5, 4-formyl-2-n-butoxy-4,5-dihydrofuran (6 and 4-formyl-1-methyl dioxabyciclo[3.3.0]oct-3-en (8, in situ. The later compounds were obtained from reaction between 3-diazo-2,4-pentadione (1, ethyl 2-diazoacetoacetate (2 or diazomalonaldehyde (3 and enol ethers using dirhodium tetraacetate as a catalyst.

Lipid-Lowering Effects of Ethyl 2-Phenacyl-3-aryl-1H-pyrrole- 4-carboxylates in Rodents

Directory of Open Access Journals (Sweden)

Bruce S. Burnham

2004-02-01

Full Text Available A series of substituted 2-phenacyl-3-phenyl-1H-pyrrole-4-carboxylates were prepared from substituted acetophenones in 6 steps. The final condensations between a chloroenal and an aminoketone were carried out under neutral conditions in parallel to yield the series listed below. Selected pyrrole derivatives proved to be potent hypolipidemic agents lowering serum triglyceride concentrations in CF-1 male mice after 14 days of I.P. administration. One agent orally lowered serum cholesterol in Sprague-Dawley male rats at 2mg/kg/day after 14 days. The agents demonstrated a lowering of mouse serum LDL- cholesterol levels and selected compounds showed an elevation of serum HDL-cholesterol levels. The cholesterol concentrations in the liver were raised while the cholesterol and triglyceride contents of the aorta were significantly lowered by the selected trisubstituted pyrrole.

Computational study on the functionalization of BNNC with pyrrole molecule

Science.gov (United States)

Payvand, Akram; Tavangar, Zahra

2018-05-01

The functionalization of the boron nitride nanocone (BNNC) by pyrrole molecule was studied using B3LYP/6-311+G(d) level of theory. The reaction was studied in three methods in different layers of the nanocone: Diels-Alder cycloaddition, quartet cycloaddition and the reaction of the nitrogen atom of the pyrrole molecule with the boron or nitrogen atom of the BNNC. Thermodynamic quantities, Chemical hardness and potential and electrophilicity index of the functionalized BNNC were studied. The results show that the tip of nanocone has a higher tendency for participation in the reaction and the most favorable product of the reaction between BNNC and pyrrole molecule is produced from the reaction of N atom of pyrrole with the B atom of BNNC. The reaction decreases the energy gap value which leads to increasing the reactivity and conductivity of functionalized nanocone. The calculated NICS values confirm the aromaticity in the pristine nanocone as well as in the functionalized nanocone.

Interaction of derived polymers from pyrrole with biocompatible solutions; Interaccion de polimeros derivados de pirrol con soluciones biocompatibles

Energy Technology Data Exchange (ETDEWEB)

Lopez G, O. G.

2010-07-01

This work presents a study about the synthesis by plasma, the electric properties and superficial interaction of polymers derived from pyrrole doped with Iodine with potential use as bio material. Poly-pyrrole is a semiconductor and biocompatible polymer with potential application in the development of artificial muscles and implants where the electric interaction between cells and material is an important variable. The syntheses were made at 13.5 MHz in a glass tubular reactor of 1500 cm{sup 3} with electrodes of 6.5 cm diameter and stainless steel flanges. An electrode was connected to the RF terminal of the power supply that is combined with a matching coupling resistance. The monomer and dopant used in this work were pyrrole and Iodine respectively, in closed containers. They were vaporized and injected separately into the reactor at room temperature and 0.1 mbar. The vapors of the reagents mixed freely in the reactor. The synthesis time was 240 min at 40, 60, 80 and 100 W. The polymers were obtained as thin films adhered to the reactor walls. The films were washed and swollen with distilled water and removed from the reactor walls with a small spatula. The polymers were irradiated with gamma rays at 18 and 22 KGy. Due to the fact that the doses are cumulative, the final dose applied was 40 KGy. The polymers characterization was carried out by Fourier Transform Infrared Spectroscopy, thermogravimetric analysis (TGA), scanning electron microscopy, contact angle, electrical conductivity and X-ray diffraction. The analyses indicates that the polymers have very similar structure in almost the entire power range, showing C-O, C=C, C-H, O-H, N-H bonds with a predominantly amorphous structure. The TGA analyses showed that the material has 4 or 5 loses of material. The first one starts after that 115 C except for the material irradiated at 40 KGy, this one begins in 87 C, the second one is in the interval of 196 and 295 C, the third one between 311 and 500 C, and the

Effect of alkali metal ions on the pyrrole and pyridine π-electron systems in pyrrole-2-carboxylate and pyridine-2-carboxylate molecules: FT-IR, FT-Raman, NMR and theoretical studies

Science.gov (United States)

Świderski, G.; Wojtulewski, S.; Kalinowska, M.; Świsłocka, R.; Lewandowski, W.

2011-05-01

The FT-IR, FT-Raman and 1H and 13C NMR spectra of pyrrole-2-carboxylic acid (PCA) and lithium, sodium, potassium, rubidium and caesium pyrrole-2-carboxylates were recorded, assigned and compared in the Li → Na → K → Rb → Cs salt series. The effect of alkali metal ions on the electronic system of ligands was discussed. The obtained results were compared with previously reported ones for pyridine-2-carboxylic acid and alkali metal pyridine-2-carboxylates. Calculations for pyrrole-2-carboxylic acid and Li, Na, K pyrrole-2-carboxylates in B3LYP/6-311++G ** level and Møller-Plesset method in MP2/6-311++G ** level were made. Bond lengths, angles and dipole moments as well as aromaticity indices (HOMA, EN, GEO, I 6) for the optimized structures of pyrrole-2-carboxylic acid (PCA) and lithium, sodium, potassium pyrrole-2-carboxylates were also calculated. The degree of perturbation of the aromatic system of ligand under the influence of metals in the Li → Cs series was investigated with the use of statistical methods (linear correlation), calculated aromaticity indices and Mulliken, NBO and ChelpG population analysis method. Additionally, the Bader theory (AIM) was applied to setting the characteristic of the bond critical points what confirmed the influence of alkali metals on the pyrrole ring.

Adsorption induced modification of in-plane magnetic anisotropy in epitaxial Co and Fe/Co films on Fe(110)

Science.gov (United States)

Ślezak, M.; Ślezak, T.; Matlak, K.; DróŻdŻ, P.; Korecki, J.

2018-05-01

A study of in-plane magnetic anisotropy (MA) in epitaxial bcc Co films and Fe/Co bilayers on a Fe(110) surface is reported. Surface MA of as-deposited Co films and Fe/Co bilayers strongly depends on the Co (dCo) and Fe (dFe) thickness. Adsorption of residual gases drastically modifies in-plane MA of both Co films and Fe/Co bilayers. We present two dimensional MA maps in the (dCo, dFe) space for both as grown and adsorption-modified films. Our results indicate how to precisely engineer in-plane MA that can be controlled by dCo, dFe and is sensitive to the residual gas adsorption.

Numerical Analysis Of Hooke Jeeves-Runge Kutta To Determine Reaction Rate Equation In Pyrrole Polymerization

International Nuclear Information System (INIS)

Gunawan, Indra; Sulistyo, Harry; Rochmad

2001-01-01

The numerical analysis of Hooke Jeeves Methods combined with Runge Kutta Methods is used to determine the exact model of reaction rate equation of pyrrole polymerization. Chemical polymerization of pyrrole was conducted with FeCI 3 / pyrrole solution at concentration ratio of 1.62 mole / mole and 2.18 mole / mole with varrying temperature of 28, 40, 50, and 60 o C. FeCl 3 acts as an oxidation agent to form pyrrole cation that will polymerize. The numerical analysis was done to examine the exact model of reaction rate equation which is derived from reaction equation of initiation, propagation, and termination. From its numerical analysis, it is found that the pyrrole polymerization follows third order of pyrrole cation concentration

Characterization of Corn Starch Films Reinforced with CaCO3 Nanoparticles

Science.gov (United States)

Sun, Qingjie; Xi, Tingting; Li, Ying; Xiong, Liu

2014-01-01

The characterization of corn starch (CS) films impregnated with CaCO3 nanoparticles was investigated. Criteria such as morphology, crystallinity, water vapor permeability (WVP), opacity, and mechanical properties were the focus of the investigation. It was found that the CaCO3 contents had significant effects on the tensile properties of the nanocomposite films. The addition of CaCO3 nanoparticles to the CS films significantly increased tensile strength from 1.40 to 2.24 MPa, elongation from 79.21 to 118.98%, and Young’s modulus from 1.82 to 2.41 MPa. The incorporation of CaCO3 nanoparticles increased the opacity of films, lowered the degree of WVP and film solubility value compared to those of the CS films. The results of scanning electron microscopy (SEM) showed that with the increase of CaCO3 nanoparticles content in starch films, the roughness of the films increased, and pores or cavities were found on the surface of the films, while small cracks were observed in the structures of the fractured surfaces. X-ray diffraction showed that the addition of nanoparticles increased the peaks in the intensity of films. PMID:25188503

Ferroelectric properties of barium strontium titanate thin films grown by RF co-sputtering

Energy Technology Data Exchange (ETDEWEB)

Zapata-Navarro, A.; Marquez-Herrera, A. [CICATA-IPN, Km. 14.5 Carretera Tampico-Puerto Ind. Altamira, Altamira Tamaulipas 89600 (Mexico); Cruz-Jauregui, M.P. [CCMC-UNAM, Km. 107 Carretera Tijuana-Ensenada, Ensenada B.C. 22800 (Mexico); Calzada, M.L. [ICMM (CSIC) Madrid, Cantoblanco Madrid 28049 (Spain)

2005-08-01

In this work, we present the variation of the ferroelectric properties of Ba{sub 1-x}Sr{sub x}TiO{sub 3} films deposited on Pt/TiO{sub 2}/SiO{sub 2}/Si substrates by RF co-sputtering with 0{<=}x{<=}1. The co-sputtering was done using a single magnetron with BaTiO{sub 3}/SrTiO{sub 3} targets in a pie mosaics configuration. Smooth and uniform films were obtained using the same conditions of growth and annealing temperature. The X-ray diffraction and EDS results show that the processes were managed to obtain crystalline materials with x from 0 to 1. The behaviour of P-E loops suggests that the ferroelectric properties of the films were tuned by changing the concentration of the cation. (copyright 2005 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Evidence for nanoscale two-dimensional Co clusters in CoPt{sub 3} films with perpendicular magnetic anisotropy

Energy Technology Data Exchange (ETDEWEB)

Cross, J O [Department of Physics, University of Washington, Seattle, WA 98195 (United States); Newville, M [Consortium for Advanced Radiation Sources, University of Chicago, Chicago, IL 60637 (United States); Maranville, B B; Hellman, F [Department of Physics, University of California at San Diego, La Jolla, CA 92093 (United States); Bordel, C [Department of Physics, University of California at Berkeley, CA 94720 (United States); Harris, V G, E-mail: cbordel@berkeley.ed [Department of Electrical and Computer Engineering, Northeastern University, Boston, MA 02115 (United States)

2010-04-14

The length scale of the local chemical anisotropy responsible for the growth-temperature-induced perpendicular magnetic anisotropy of face-centered cubic CoPt{sub 3} alloy films was investigated using polarized extended x-ray absorption fine structure (EXAFS). These x-ray measurements were performed on a series of four (111) CoPt{sub 3} films epitaxially grown on (0001) sapphire substrates. The EXAFS data show a preference for Co-Co pairs parallel to the film plane when the film exhibits magnetic anisotropy, and random chemical order otherwise. Furthermore, atomic pair correlation anisotropy was evidenced only in the EXAFS signal from the next neighbors to the absorbing Co atoms and from multiple scattering paths focused through the next neighbors. This suggests that the Co clusters are no more than a few atoms in extent in the plane and one monolayer in extent out of the plane. Our EXAFS results confirm the correlation between perpendicular magnetic anisotropy and two-dimensional Co segregation in CoPt{sub 3} alloy films, and establish a length scale on the order of 10 A for the Co clusters.

Characteristics of rapid-thermal-annealed LiCoO2 cathode film for an all-solid-state thin film microbattery

International Nuclear Information System (INIS)

Kim, Han-Ki; Yoon, Young Soo

2004-01-01

We report on the fabrication of a LiCoO 2 film for an all-solid-state thin film microbattery by using a rapid-thermal-annealing (RTA) process. The LiCoO 2 films were grown by rf magnetron sputtering using a synthesized LiCoO 2 target in a [O 2 /(Ar+O 2 )] ratio of 10%. Scanning electron microscopy (SEM), x-ray photoelectron spectroscopy (XPS), and Auger electron spectroscopy (AES) analysis results showed that the surface layer on the as-deposited LiCoO 2 film was completely removed by rapid thermal annealing process in oxygen ambient for 20 min. In addition, the thin film microbattery fabricated with the annealed LiCoO 2 film shows fairly stable cyclability with a specific discharge capacity of 56.49 μAh/cm2 μm. These results show the possibility of the RTA LiCoO 2 film and rapid thermal annealing process being a promising cathode material and annealing process for thin film microbatteries, respectively

Magnetic properties of Co/Pt-Pd multilayer thin film media

Energy Technology Data Exchange (ETDEWEB)

Inaba, N.; Igarashi, S.; Fujita, F.; Koike, K.; Kato, H. [Faculty of Engineering, Yamagata University, Yonezawa, Yamagata 992-8510 (Japan); Kirino, F. [National University of Fine Arts and Music, Taitou-ku, Tokyo 110-8714 (Japan)

2007-12-15

We investigated the dependence of magnetic properties for Co/Pt{sub 100-x}Pd{sub x} multilayer thin films on the concentration in the Pt-Pd alloy layers. Perpendicular magneto anisotropy constant K {sub p} increases with increasing Pt concentration in the Pt-Pd layer, since the interface anisotropy between the Co and the Pt-Pd layers is enhanced by the increase of the Pt concentration. The Curie temperature and the temperature dependence of K{sub p} for the specimens increase with increasing the amount of Pt in the Pt-Pd layer. These results may indicate that the lattice distortion of the Co layer caused by the interface from the Pt-Pd layer becomes larger and the increase of the distortion enhances the interface anisotropy, since the lattice misfit between the Pt-Pd and the Co increases with increasing the Pt concentration. (copyright 2008 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Thin Co films with tunable ferromagnetic resonance frequency

International Nuclear Information System (INIS)

Maklakov, Sergey S.; Maklakov, Sergey A.; Ryzhikov, Ilya A.; Rozanov, Konstantin N.; Osipov, Alexey V.

2012-01-01

The tailored production of thin Co films of 50 nm thick with ferromagnetic resonance frequency in a range from 2.9 to 7.3 GHz using the DC magnetron sputtering is reported. The ferromagnetic resonance frequency, coercivity, effective magnetic field and nanocrystalline structure parameters are shown to be governed by the Co deposition rate. For this investigation, FMR, VSM and TEM techniques were used. - Highlights: ► Thin Co films with FMR frequency in a range from 2.9 to 7.3 GHz are obtained. ► The films' properties are governed by the deposition rate during DC magnetron sputtering. ► FMR, VSM and TEM techniques were used during the study.

In situ surface X-ray diffraction study of ultrathin epitaxial Co films on Au(111) in alkaline solution

International Nuclear Information System (INIS)

Reikowski, Finn; Maroun, Fouad; Di, Nan; Allongue, Philippe; Ruge, Martin; Stettner, Jochim; Magnussen, Olaf M.

2016-01-01

The oxidation behavior of ultrathin electrodeposited Co films on Au(111) in alkaline electrolyte was studied using in situ surface X-ray scattering techniques employing synchrotron radiation and complementary optical reflectivity and electrochemical measurements. The films are formed at pH 4 and consist of (001)-oriented hcp Co crystallites that are several nm high, a few ten nm in diameter, and remain largely unchanged after electrolyte exchange to pH 12 solution. In the pre-oxidation peak only minor changes were observed in the diffraction studies, excluding the formation of Co(OH)_2 layers. In the potential regime of Co hydroxide formation a rapid reduction of the amount of Co is observed, while the characteristic height of the islands decreases only slightly. On longer times scales, growth of 3D crystals of Co(OH)_2 occurs as well as irreversible Co dissolution into the electrolyte is found. On the basis of the structural observations oxidation of the Co film is proposed to proceed via fast formation of an ultrathin passivating layer, followed by nucleation and growth of 3D hydroxide crystals at the grain boundaries in the Co deposit.

Electrodeposited Fe-Co films prepared from a citric-acid-based plating bath

OpenAIRE

Yanai, Takeshi; Uto, H.; Shimokawa, Takaya; Nakano, Masaki; Fukunaga, Hirotoshi; Suzuki, K.

2013-01-01

Electrodeposited Fe-Co films are commonly prepared in a boric-acid-based bath. In this research, we applied citric acid instead of boric acid for the plating of Fe-Co films because boron in the waste bath is restricted by environmental-protection regulations in Japan. We evaluated the effect of citric acid on the magnetic and structural properties of the films. The saturation magnetization of the Fe-Co films slightly increased while the Fe content in the Fe-Co films decreased with increasing ...

Resistance switching in epitaxial SrCoOx thin films

Science.gov (United States)

Tambunan, Octolia T.; Parwanta, Kadek J.; Acharya, Susant K.; Lee, Bo Wha; Jung, Chang Uk; Kim, Yeon Soo; Park, Bae Ho; Jeong, Huiseong; Park, Ji-Yong; Cho, Myung Rae; Park, Yun Daniel; Choi, Woo Seok; Kim, Dong-Wook; Jin, Hyunwoo; Lee, Suyoun; Song, Seul Ji; Kang, Sung-Jin; Kim, Miyoung; Hwang, Cheol Seong

2014-08-01

We observed bipolar switching behavior from an epitaxial strontium cobaltite film grown on a SrTiO3 (001) substrate. The crystal structure of strontium cobaltite has been known to undergo topotactic phase transformation between two distinct phases: insulating brownmillerite (SrCoO2.5) and conducting perovskite (SrCoO3-δ) depending on the oxygen content. The current-voltage characteristics of the strontium cobaltite film showed that it could have a reversible insulator-to-metal transition triggered by electrical bias voltage. We propose that the resistance switching in the SrCoOx thin film could be related to the topotactic phase transformation and the peculiar structure of SrCoO2.5.

Resistance switching in epitaxial SrCoOx thin films

International Nuclear Information System (INIS)

Tambunan, Octolia T.; Parwanta, Kadek J.; Acharya, Susant K.; Lee, Bo Wha; Jung, Chang Uk; Kim, Yeon Soo; Park, Bae Ho; Jeong, Huiseong; Park, Ji-Yong; Cho, Myung Rae; Park, Yun Daniel; Choi, Woo Seok; Kim, Dong-Wook; Jin, Hyunwoo; Lee, Suyoun; Song, Seul Ji; Kang, Sung-Jin; Kim, Miyoung; Hwang, Cheol Seong

2014-01-01

We observed bipolar switching behavior from an epitaxial strontium cobaltite film grown on a SrTiO 3 (001) substrate. The crystal structure of strontium cobaltite has been known to undergo topotactic phase transformation between two distinct phases: insulating brownmillerite (SrCoO 2.5 ) and conducting perovskite (SrCoO 3−δ ) depending on the oxygen content. The current–voltage characteristics of the strontium cobaltite film showed that it could have a reversible insulator-to-metal transition triggered by electrical bias voltage. We propose that the resistance switching in the SrCoO x thin film could be related to the topotactic phase transformation and the peculiar structure of SrCoO 2.5

Biosynthesis, asymmetric synthesis, and pharmacology, including cellular targets, of the pyrrole-2-aminoimidazole marine alkaloids

Digital Repository Service at National Institute of Oceanography (India)

Al-Mourabit, A.; Zancanella, M.A.; Tilvi, S.; Romo, D.

The pyrrole-2-aminoimidazole (P-2-AI) alkaloids are a growing family of marine alkaloids, now numbering well over 150 members, with high topographical and biological information content. Their intriguing structural complexity, rich and compact...

A facile approach to prepare crumpled CoTMPyP/electrochemically reduced graphene oxide nanohybrid as an efficient electrocatalyst for hydrogen evolution reaction

Energy Technology Data Exchange (ETDEWEB)

Ma, Juanjuan, E-mail: majj0518@hotmail.com [Department of Chemical Engineering, Huaihai Institute of Technology, Lianyungang 222005 (China); School of Materials Science and Engineering, Nanyang Technological University, 639798, Singapore (Singapore); Liu, Lin; Chen, Qian; Yang, Min [Department of Chemical Engineering, Huaihai Institute of Technology, Lianyungang 222005 (China); Wang, Danping [School of Materials Science and Engineering, Nanyang Technological University, 639798, Singapore (Singapore); Tong, Zhiwei [Department of Chemical Engineering, Huaihai Institute of Technology, Lianyungang 222005 (China); Chen, Zhong, E-mail: aszchen@ntu.edu.sg [School of Materials Science and Engineering, Nanyang Technological University, 639798, Singapore (Singapore)

2017-03-31

Highlights: • Crumpled CoTMPyP/ERGO hybrid was successfully prepared by a facile two-step process. • CoTMPyP nanoaggregates are homogeneously distributed over the graphene surface. • CoTMPyP/ERGO hybrid film shows good electrocatalytic activity and stability for HER. - Abstract: Elaborate design and synthesis of efficient and stable non-Pt electrocatalysts for some renewable energy related conversion/storage processes are one of the major goals of sustainable chemistry. Herein, we report a facile method to fabricate Co porphyrin functionalized electrochemically reduced graphene oxide (CoTMPyP/ERGO) thin film by direct assembly of oppositely charged tetrakis(N-methylpyridyl) porphyrinato cobalt (CoTMPyP) and GO nanosheets under mild conditions followed by an electrochemical reduction procedure. STEM analysis confirms that CoTMPyP nanoaggregates are homogeneously distributed over the graphene surface. The electrochemical properties of CoTMPyP/ERGO were investigated by cyclic voltammetry, linear sweep voltammetry and electrochemical impedance spectroscopy. The results demonstrate that CoTMPyP/ERGO nanohybrid film can serve as excellent electrocatalyst for hydrogen evolution in alkaline solution with high activity and stability. The intimate contact and efficient electron transfer between CoTMPyP and ERGO, as well as the crumpled structure, contribute to the improvement of the electrocatalytic performance.

Characteristics of Al/p-AgGaTe2 polycrystalline thin film Schottky barrier diode

International Nuclear Information System (INIS)

Patel, S.S.; Patel, B.H.; Patel, T.S.

2008-01-01

An Al/p-AgGaTe 2 polycrystalline thin film schottky barrier diode have been prepared by flash-evaporation of p-AgGaTe 2 onto a pre-deposited film of aluminium. The current-voltage, capacitance-voltage and photoresponse of the diode have been investigated. The important physical parameter such as barrier height of the fabricated diode was derived from these measurements. (copyright 2008 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Theoretical study of structure and electronic properties of cyano-substituted pyrroles

International Nuclear Information System (INIS)

Rimarcik, Jan; Lukes, Vladimir; Klein, Erik; Griesser, Markus; Kelterer, Anne-Marie

2008-01-01

DFT and ab initio MP2 calculations of optimal geometries, dipole moments, polarizabilities, excitation energies and enthalpies of hydrogen or proton transfer from N-H group for cyano derivatives of pyrrole are presented. CN groups in α and β positions have distinct effects on electron spectra absorption bands. CN in α position causes larger bathochromic shift in comparison to β position. N-H bond dissociation enthalpies (BDE) of substituted pyrroles are higher by 7 kJ mol -1 than pyrrole BDE. Number and position of CN groups do not affect BDEs. Proton affinities of pyrrolyl anions and enthalpies of electron transfer from these anions are proportional to the number of CN groups in molecule. Each CN group causes decrease in proton affinity by 72 kJ mol -1 and 73 kJ mol -1 rise in electron transfer enthalpy. For several studied pyrroles, BDEs, proton affinities and electron transfer enthalpies in water and benzene were computed

Electrodeposition and Capacitive Behavior of Films for Electrodes of Electrochemical Supercapacitors

Directory of Open Access Journals (Sweden)

Shi C

2010-01-01

Full Text Available Abstract Polypyrrole films were deposited by anodic electropolymerization on stainless steel substrates from aqueous pyrrole solutions containing sodium salicylate and tiron additives. The deposition yield was studied under galvanostatic conditions. The amount of the deposited material was varied by the variation of deposition time at a constant current density. SEM studies showed the formation of porous films with thicknesses in the range of 0–3 μm. Cyclic voltammetry data for the films tested in 0.5 M Na2SO4 solutions showed capacitive behavior and high specific capacitance (SC in a voltage window of 0.9 V. The films prepared from pyrrole solutions containing tiron showed better capacitive behavior compared to the films prepared from the solutions containing sodium salicylate. A highest SC of 254 F g−1 was observed for the sample with a specific mass of 89 μg cm−2 at a scan rate of 2 mV s−1. The SC decreased with an increasing film thickness and scan rate. The results indicated that the polypyrrole films deposited on the stainless steel substrates by anodic electropolymerization can be used as electrodes for electrochemical supercapacitors (ES.

Electrodeposition and Capacitive Behavior of Films for Electrodes of Electrochemical Supercapacitors

Science.gov (United States)

Shi, C.; Zhitomirsky, I.

2010-03-01

Polypyrrole films were deposited by anodic electropolymerization on stainless steel substrates from aqueous pyrrole solutions containing sodium salicylate and tiron additives. The deposition yield was studied under galvanostatic conditions. The amount of the deposited material was varied by the variation of deposition time at a constant current density. SEM studies showed the formation of porous films with thicknesses in the range of 0-3 μm. Cyclic voltammetry data for the films tested in 0.5 M Na2SO4 solutions showed capacitive behavior and high specific capacitance (SC) in a voltage window of 0.9 V. The films prepared from pyrrole solutions containing tiron showed better capacitive behavior compared to the films prepared from the solutions containing sodium salicylate. A highest SC of 254 F g-1 was observed for the sample with a specific mass of 89 μg cm-2 at a scan rate of 2 mV s-1. The SC decreased with an increasing film thickness and scan rate. The results indicated that the polypyrrole films deposited on the stainless steel substrates by anodic electropolymerization can be used as electrodes for electrochemical supercapacitors (ES).

Electromechanical response of silk fibroin hydrogel and conductive polycarbazole/silk fibroin hydrogel composites as actuator material.

Science.gov (United States)

Srisawasdi, Thanida; Petcharoen, Karat; Sirivat, Anuvat; Jamieson, Alexander M

2015-11-01

Pure silk fibroin (SF) hydrogel and polycarbazole/silk fibroin (SF/PCZ) hydrogels were fabricated by solvent casting technique to evaluate electromechanical responses, dielectric properties, and cantilever deflection properties as functions of electric field strength, SF concentration, glutaraldehyde concentration, and PCZ concentration in the blends. Electromechanical properties were characterized in oscillatory shear mode at electric field strengths ranging from 0 to 600V/mm and at a temperature of 27°C. For both the pristine SF and SF/PCZ hydrogels, the storage modulus response (ΔG') and the storage modulus sensitivity (ΔG'/G'0) increased dramatically with increasing electric field strength. The pristine hydrogel possessed the highest storage modulus sensitivity value of 5.87, a relatively high value when compared with other previously studied electroactive polymers. With the addition of conductive PCZ in SF hydrogel, the storage modulus sensitivity and the relative dielectric constant decreased; the conductive polymer thus provided the softening effect under electric field. In the deflection response, the dielectrophoresis force and deflection distance increased monotonically with electric field strength, where the pure SF hydrogel showed the highest deflection distance and dielectrophoresis force. Copyright © 2015 Elsevier B.V. All rights reserved.

P-type Al-doped Cr-deficient CrN thin films for thermoelectrics

Science.gov (United States)

le Febvrier, Arnaud; Van Nong, Ngo; Abadias, Gregory; Eklund, Per

2018-05-01

Thermoelectric properties of chromium nitride (CrN)-based films grown on c-plane sapphire by dc reactive magnetron sputtering were investigated. In this work, aluminum doping was introduced in CrN (degenerate n-type semiconductor) by co-deposition. Under the present deposition conditions, over-stoichiometry in nitrogen (CrN1+δ) rock-salt structure is obtained. A p-type conduction is observed with nitrogen-rich CrN combined with aluminum doping. The Cr0.96Al0.04N1.17 film exhibited a high Seebeck coefficient and a sufficient power factor at 300 °C. These results are a starting point for designing p-type/n-type thermoelectric materials based on chromium nitride films, which are cheap and routinely grown on the industrial scale.

Synchrotron photoemission study of (Zn,Co)O films with uniform Co distribution

DEFF Research Database (Denmark)

Guziewicz, E.; Lukasiewicz, M. I.; Wachnicki, L.

2011-01-01

of foreign phases and metal accumulations as indicated by TEM data. The electronic structure of (Zn,Co)O films was studied by Resonant Photoemission Spectroscopy across the Co3p–Co3d photoionization threshold. We have observed that the resonant enhancement of the photoemission intensity from the Co3d shell...

In situ electrodeposition of CoP nanoparticles on carbon nanomaterial doped polyphenylene sulfide flexible electrode for electrochemical hydrogen evolution

Science.gov (United States)

Wang, Tingxia; Jiang, Yimin; Zhou, Yaxin; Du, Yongling; Wang, Chunming

2018-06-01

Active and durable electrocatalyst for hydrogen evolution reaction (HER) is pivotal to generate molecular hydrogen more energy-efficient, but directly grafting electrocatalyst on electrode material by a single-step method without compromising the catalytic activity and stability remains a challenge. Herein, an intriguing electrode, reduced graphene oxide modified carbon nanotube/reduced graphene oxide/polyphenylene sulfide (RGO-CNT/RGO/PPS) film, is used to replace conventional electrodes. In situ electrodeposition is proposed to fabricate CoP on the RGO-CNT/RGO/PPS (CoP-RGO-CNT/RGO/PPS) electrode and achieves a favorably electrical contact between CoP nanoparticles and RGO-CNT/RGO/PPS electrode due to without any polymer binder. Additionally, the coupling of different electrodeposition stages with scanning electron microscope (SEM) can investigate the nanostructure evolution of CoP nanoparticles, which gives valuable insights into the optimized electrodeposition cycles. The rational integration of RGO onto CNT/RGO/PPS film is an effective approach for enhancing its intrinsic electrical conductivity and favoring the formation of a high density of dispersive CoP nanoparticles. The CoP-RGO-CNT/RGO/PPS film has shown outstanding HER electrocatalytic behaviors performed a current density of 10 mA cm-2 at a relatively low overpotential of 160 mV with a Tafel slope of 60 mV dec-1 in acidic medium, which can be mainly attributed to the synergistic effect between optimized morphology and accelerated kinetics. Additionally, this film electrocatalyst exhibits a good HER activity and stability under both neutral and basic conditions.

Co-sputtered optical films

Energy Technology Data Exchange (ETDEWEB)

Misiano, C; Simonetti, E [Selenia S.p.A., Rome (Italy)

1977-06-01

The co-sputtering of two dielectric materials with indices of refraction as widely different as possible has been investigated with the aim of obtaining both homogeneous films with an intermediate index of refraction and inhomogeneous films with predetermined profiles. An rf sputtering module is described which has been especially designed, with two separate cathodes and two independent tunable rf generators. The substrates are placed on a circular anode rotating underneath the two cathodes. So far mainly CeO/sub 2/, TiO2 and SiO/sub 2/ targets have been used. The deposition rate from each cathode and the total film thickness are determined by means of two quartz thickness monitors, sputtering compatible. Values obtained for the refractive index and optical thickness are reported, as well as repeatability, mechanical and chemical characteristics, reliability and high power optical radiation resistance. Finally, results obtained on optical components of practical interest are discussed.

Characterisation of magnetron sputtered SmCo5 thin films

International Nuclear Information System (INIS)

Wang, Y.; Sood, D.K.; Kothari

1999-01-01

SmCo 5 thin films were deposited using DC magnetron sputtering on single crystal silicon substrate with chromium and SiO 2 top layers. Deposition was carried out at three different substrate temperatures: room temperature, 400 deg C and 600 deg C. Films were characterised by using Rutherford Backscattering Spectroscopy (RBS), X-ray Diffraction (XRD), Secondary Ion Mass Spectrometry (SIMS) and SQUID magnetometer. RBS analysis indicated that the films have excellent stoichiometry with the Sm to Co ratio of 1:5. This analysis also showed that the films deposited or annealed at high temperatures (≥600 deg C) indicated significant inter-diffusion at the interface between the barrier layer and the film. Oxygen was found to be the major impurity in the films. XRD data indicated that the films formed 1:5 and 2:17 phases under different deposition conditions. The preliminary studies of these films using magnetic force microscopy revealed the presence of magnetic domains

Structure and magnetization of Co4N thin film

Science.gov (United States)

Pandey, Nidhi; Gupta, Mukul; Gupta, Rachana; Rajput, Parasmani; Stahn, Jochen

2018-02-01

In this work, we studied the local structure and the magnetization of Co4N thin films deposited by a reactive dc magnetron sputtering process. The interstitial incorporation of N atoms in a fcc Co lattice is expected to expand the structure. This expansion yields interesting magnetic properties e.g. a larger magnetic moment (than Co) and a very high value of spin polarization ratio in Co4N . By optimizing the growth conditions, we prepared Co4N film having lattice parameter close to its theoretically predicted value. The N concentration was measured using secondary ion mass spectroscopy. Detailed magnetization measurements using bulk magnetization method and polarized neutron reflectivity confirm that the magnetic moment of Co in Co4N is higher than that of Co.

Growth and structure of Co/Au magnetic thin films; Croissance et structure des couches minces magnetiques Co/Au

Energy Technology Data Exchange (ETDEWEB)

Marsot, N

1999-01-14

We have studied the growth and the crystallographic structure of magnetic ultra thin cobalt/gold films (Co/Au), in order to investigate the correlations between their magnetic and structural properties. Room temperature (R.T.) Co growth on Au (111) proceeds in three stages. Up to 2 Co monolayers (ML), a bilayer island growth mode is observed. Between 2 and 5 ML, coalescence of the islands occurs, covering the substrate surface and a Co/Au mixing is observed resulting from the de-construction of the Herringbone reconstruction. Finally, beyond 5 ML, the CoAu mixing is buried and the Co growth continues in a 3-D growth. Annealing studies at 600 K on this system show a smoothing effect of the Co film, and at the same time, segregation of Au atoms. The quality of the Co/Au interface (sharpness) is not enhanced by the annealing. The local order was studied by SEXAFS and the long range order by GIXRD showing that the Co film has a hexagonal close packed structure, with an easy magnetization axis perpendicular to the surface. From a local order point of view, the Co grows with an incoherent epitaxy and keeps its own bulk parameters. The GIXRD analysis shows a residual strain in the Co film of 4%. The difference observed between the local order analysis and the long range order results is explained in terms of the low dimensions of the diffracting domains. The evolution of film strains, as a function of the Co coverage, shows a marked deviation from the elastic strain theory. Modification of the strain field in the Co film as a function of the Au coverage is studied by GIXRD analysis. The Au growth study, at R.T., shows no evidence of a Au/Co mixing in the case of the Au/Co interface. The Au overlayer adopts a twinned face centred cubic structure on the rough Co film surface. (author)

Structure and Oxidation of Pyrrole Adducts Formed between Aflatoxin B2a and Biological Amines.

Science.gov (United States)

Rushing, Blake R; Selim, Mustafa I

2017-06-19

Aflatoxin B 2a has been shown to bind to proteins through a dialdehyde intermediate under physiological conditions. The proposed structure of this adduct has been published showing a Schiff base interaction, but adequate verification using structural elucidation instrumental techniques has not been performed. In this work, we synthesized the aflatoxin B 2a amino acid adduct under alkaline conditions, and the formation of a new product was determined using high performance liquid chromatography-time-of-flight mass spectrometry. The resulting accurate mass was used to generate a novel proposed chemical structure of the adduct in which the dialdehyde forms a pyrrole ring with primary amines rather than the previously proposed Schiff base interaction. The pyrrole structure was confirmed using 1 H, 13 C, correlation spectroscopy, heteronuclear single quantum correlation, and heteronuclear multiple bond correlation NMR and tandem mass spectrometry. Reaction kinetics show that the reaction is overall second order and that the rate increases as pH increases. Additionally, this study shows for the first time that aflatoxin B 2a dialdehyde forms adducts with phosphatidylethanolamines and does so through pyrrole ring formation, which makes it the first aflatoxin-lipid adduct to be structurally identified. Furthermore, oxidation of the pyrrole adduct produced a product that was 16 m/z heavier. When the aflatoxin B 2a -lysine (ε) adduct was oxidized, it gave a product with an accurate mass, mass fragmentation pattern, and 1 H NMR spectrum that match aflatoxin B 1 -lysine, which suggest the transformation of the pyrrole ring to a pyrrolin-2-one ring. These data give new insight into the fate and chemical properties of biological adducts formed from aflatoxin B 2a as well as possible interferences with known aflatoxin B 1 exposure biomarkers.

Preparation of p-type transparent conducting tin-antimony oxide thin films by DC reactive magnetron sputtering

Energy Technology Data Exchange (ETDEWEB)

Ji, Zhenguo [College of Electronic Information, Hangzhou Dianzi University, Hangzhou (China); State Key Laboratory for Silicon Materials, Zhejiang University, Hangzhou (China); Xi, Junhua; Huo, Lijuan; Zhao, Yi [State Key Laboratory for Silicon Materials, Zhejiang University, Hangzhou (China)

2008-07-01

P-type transparent conducting tin-antimony oxide (TAO) films were successfully prepared by DC reactive magnetron sputtering followed by post annealing in the air. Structural, optical and electrical properties of the TAO films were investigated. X-ray diffraction studies showed that the films are polycrystalline with orthorhombic structure of Sb{sub 2}O{sub 4}. UV-Visible absorption and transmittance spectra showed that the optical band-gap of the TAO films is about 3.90 eV, and the overall transmittance is higher than 85% in the visible region. Hall effect measurement indicated that the Sn/Sb ratio is a critical parameter to get p-type conducting TAO films. It was found that 0.19p-type TAO films could be obtained. Hole concentration as high as 4.03 x 10{sup 19} cm{sup -3} and electrical resistivity as low as 0.155 {omega}cm were achieved, showing potential applications of TAO films as p-type transparent conducting films. (copyright 2008 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Thermoelectric properties of cobalt–antimonide thin films prepared by radio frequency co-sputtering

Energy Technology Data Exchange (ETDEWEB)

Ahmed, Aziz; Han, Seungwoo, E-mail: swhan@kimm.re.kr

2015-07-31

Co–Sb thin films with an Sb content in the range 65–76 at.%, were deposited on a thermally oxidized Si (100) substrate preheated at 200 °C using radio-frequency co-sputtering. Evaluation using scanning electron microscopy images and X-ray diffraction reveals that the films were polycrystalline, with a grain size in the range 100–250 nm. Energy-dispersive spectroscopy analysis indicates single-phase CoSb{sub 2} and CoSb{sub 3} films, as well as multiphase thin films with either CoSb{sub 2} or CoSb{sub 3} as the dominant phase. The electrical and thermoelectric properties were measured and found to be strongly dependent on the observed phases and the defect concentrations. The CoSb{sub 2} thin films were found to exhibit a significant n-type thermoelectric effect, which, coupled with the very low electrical resistivity, resulted in a larger power factor than that of the CoSb{sub 3} thin films. We find power factors of 0.73 mWm{sup −1} K{sup −2} and 0.67 mWm{sup −1} K{sup −2} for the CoSb{sub 2} and CoSb{sub 3} thin films, respectively. - Highlights: • Polycrystalline Co–Sb thin films were obtained by present deposition strategy. • CoSb{sub 2} and CoSb{sub 3} have semimetal and semiconductor characteristics respectively. • The Seebeck coefficient depends heavily on defect concentration and impurity phases. • Film properties in the second heating cycle were different from the first. • CoSb{sub 2} is found to possess significant n-type thermopower.

Corrosion properties of the Mg alloy coated with polypyrrole films

International Nuclear Information System (INIS)

Grubač, Zoran; Rončević, Ivana Škugor; Metikoš-Huković, Mirjana

2016-01-01

Highlights: • Electropolymerization of pyrrole on Mg-alloy surface in presence of salicylate. • Salicylate dual role in PPy deposition: passivation and electron transfer mediation. • Redox potential of salicylate corresponds to potential of PPy nucleation. • EIS and polarization corrosion studies of PPy coated Mg-alloy in Hanks’ solution. • Polypyrrole significantly slowdown Mg alloy corrosion in Hanks’ solution. - Abstract: In the present study the reactive surface of Mg alloy was coated with the nontoxic biocompatible polypyrrole (PPy) film synthesized by electrochemical oxidation from an aqueous salicylate solution. Salicylate ions prevent Mg dissolution and act as an electron transfer mediator during the PPy film nucleation, formation and growth on the alloy surface. Kinetics of the pyrrole polymerization as well as corrosion resistance of the PPy coated Mg alloy in the Hanks’ solution were investigated using dc electrochemical methods and electrochemical impedance spectroscopy (EIS). Characterization of the surface film was performed by optical and Fourier transform infrared spectroscopy (FTIR).

Investigation of structure and magnetoresistance in Co/ZnO films

International Nuclear Information System (INIS)

Quan Zhiyong; Xu Xiaohong; Li Xiaoli; Feng, Q.; Gehring, G. A.

2010-01-01

Co/ZnO films were deposited on glass substrates by magnetron sputtering at room temperature. The structure of the as-deposited films is studied by means of x-ray diffraction, x-ray photoelectron spectroscopy, and the zero-field-cooled and field-cooled magnetization curves. It is shown that the as-deposited samples consist of a mixture of regions of metallic Co and semiconducting ZnO. Large negative magnetoresistance of 26% and 11.9% are observed in the as-deposited Co/ZnO film with Co concentration of 50.7 at. % at 10 K and room temperature, respectively. Structural analysis, the temperature dependence of the conductivity and magnetoresistance reveal that the magnetoresistance is induced by spin-dependent tunneling between regions of conducting magnetic Co through the ZnO semiconducting barriers. The enhanced magnetoresistance in the low temperature regime may be related to the existence of higher-order tunneling processes between large Co regions mediated by small Co particles.

Structural and magnetic properties of SmCo-based magnetic films grown by electron-beam evaporation

Energy Technology Data Exchange (ETDEWEB)

Saravanan, P., E-mail: psdrdo@gmail.com [Defence Metallurgical Research Laboratory, Hyderabad 500058 (India); Vinod, V.T.P.; Černík, Miroslav [Institute for Nanomaterials, Advanced Technologies and Innovation, Department of Natural Sciences, Technical University of Liberec, Studentská 1402/2, Liberec 1, 461 17 (Czech Republic); Vishnuraj, R.; Arout Chelvane, J.; Kamat, S.V. [Defence Metallurgical Research Laboratory, Hyderabad 500058 (India); Hsu, Jen-Hwa, E-mail: jhhsu@phys.ntu.edu.tw [Department of Physics, National Taiwan University, Taipei 106, Taiwan (China)

2015-07-01

Sub-micron thick Sm–Co films (200 and 300 nm) with selective phase composition are grown on Si (100) substrates by electron-beam evaporation using Sm-lean alloy targets such as Sm{sub 4}Co{sub 96} and Sm{sub 8}Co{sub 92}. The structural and magnetic properties of Sm–Co films are characterized by x-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM) and super-conducting quantum interference device (SQUID) magnetometer. The Sm–Co films obtained with the Sm{sub 4}Co{sub 96} target exhibit Sm{sub 2}Co{sub 17} as a prominent phase; while the films produced with the Sm{sub 8}Co{sub 92} target show Sm{sub 2}Co{sub 7} as a major phase. Both the Sm–Co films reveal granular morphology; however, the estimated grain size values are slightly lower in the case of Sm{sub 2}Co{sub 7} films, irrespective of their thicknesses. Coercivity (H{sub c}) values of 1.48 and 0.9 kOe are achieved for the as-grown 200-nm thick Sm{sub 2}Co{sub 17} and Sm{sub 2}Co{sub 7}-films. Temperature-dependent magnetization studies confirm that the demagnetization behaviors of these films are consistent with respect to the identified phase composition. Upon rapid thermal annealing, maximum H{sub c} value of 8.4 kOe is achieved for the 200 nm thick Sm{sub 2}Co{sub 17}-films. As far as e-beam evaporated Sm–Co films are concerned, this H{sub c} value is one of the best values reported so far. - Highlights: • Electron-beam evaporation was exploited to grow sub-μm thick Sm–Co films. • Sm{sub 2}Co{sub 7} and Sm{sub 2}Co{sub 17} magnetic phases were crystallized using Sm-lean alloy targets. • Both 200 and 300-nm thick Sm–Co films revealed distinct granular morphology. • Sm–Co films of lower thickness exhibited high H{sub c} and low M{sub s} and vice-versa. • Coercivity value of 8.4 kOe achieved for the 200-nm thick Sm{sub 2}Co{sub 17}-films after RTA.

2,5-Dimethyl-1-phenylsulfonyl-1H-pyrrole-3,4-dicarbaldehyde

Directory of Open Access Journals (Sweden)

2009-03-01

Full Text Available In the title compound, C14H13NO4S, the mean planes of the pyrrole and phenyl rings form a dihedral angle of 88.7 (1°. The aldehyde groups are slightly twisted from the pyrrole plane. In the crystal structure, molecules are linked into a three-dimensional framework by C—H...O hydrogen bonds.

Magnetoresistance anomaly in DyFeCo thin films

International Nuclear Information System (INIS)

Wu, J. C.; Wu, C. S.; Wu, Te-ho; Chen, Bing-Mau; Shieh, Han-Ping D.

2001-01-01

Microstructured rare-earth - transition-metal DyFeCo films have been investigated using magnetoresistance and extraordinary Hall-effect measurements. The Hall loops reveal variation of coercive fields depending on the linewidth and the composition of the films. The magnetoresistance curves, with changes up to as high as 1.3%, show positive/negative magnetoresistance peaks centered on the coercive fields depending on the linewidth of the films only. The variation of the coercivity can be attributed to the magnetic moment canting between the Dy and FeCo subcomponents and the existence of the diverged magnetization on the edges, and the anomalous magnetoresistance peaks observed are discussed with the existing theories. [copyright] 2001 American Institute of Physics

Influence of co-electrodeposited Gold particles on the electrocatalytic properties of CoHCF thin films

International Nuclear Information System (INIS)

Kumar, Alam Venugopal Narendra; Joseph, James

2014-01-01

The electrochemical modification of solid electrodes with metal hexacyanoferrate thin films for enhancing the interfacial properties has created interest for over the past three decades. The preparation of Prussian blue (PB) Au nano composites for the enhancement in the electrocatalytic properties of PB on glassy carbon electrode has been reported by us. The incorporation of Au nano particles in Cobalt hexacyanoferrate (CoHCF) films on Glassy carbon by co-electrodeposition is expected to benefit its interfacial electron transfer properties. The present work describes the effect on the interfacial properties by incorporated Au particles in CoHCF (CoHCF(Au)) modified electrodes. The CoHCF(Au) modified electrodes were characterized by UV-Vis spectrophotometry, Cyclic Voltammetry, AC Impedance, FE-SEM etc., Influence on the electrocatalytic properties of CoHCF(Au) films have been explored by performing two important reactions i) Hydrazine elecrtro-oxidation ii) Oxygen evolution reaction. Our results reveal that CoHCF(Au) modified GC electrode perform better in terms of charge transport in the redox film and also for the electrooxidation of hydrazine in comparision with simple CoHCF modified electrodes. By using the current-transient technique (chrono method i vs t curve) the hydrazine diffusion coefficient (D 0 ) were calculated. Diffusion coefficient of hydrazine was approximately three times higher on CoHCF(Au) electrode, 9.5 × 10 −5 cm 2 s −1 compared with simple CoHCF modified electrode, 3.3× 10 −5 cm 2 s −1 . Similarly, we also discuss results which reveal that CoHCF(Au) electrodes enhances electrocatalytic activity in splitting water to oxygen in 0.1 M NaOH solution compared to simple CoHCF and Au deposited on GC electrodes

Synthesis and characterisation of co-evaporated tin sulphide thin films

Science.gov (United States)

Koteeswara Reddy, N.; Ramesh, K.; Ganesan, R.; Ramakrishna Reddy, K. T.; Gunasekhar, K. R.; Gopal, E. S. R.

2006-04-01

Tin sulphide films were grown at different substrate temperatures by a thermal co-evaporation technique. The crystallinity of the films was evaluated from X-ray diffraction studies. Single-phase SnS films showed a strong (040) orientation with an orthorhombic crystal structure and a grain size of 0.12 μm. The films showed an electrical resistivity of 6.1 Ω cm with an activation energy of 0.26 eV. These films exhibited an optical band gap of 1.37 eV and had a high optical absorption coefficient (>104 cm-1) above the band-gap energy. The results obtained were analysed to evaluate the potentiality of the co-evaporated SnS films as an absorber layer in solar photovoltaic devices.

Optical and magneto-optical characterization of TbFeCo and GdFeCo thin films for high-density recording

International Nuclear Information System (INIS)

Hendren, W R; Atkinson, R; Pollard, R J; Salter, I W; Wright, C D; Clegg, W W; Jenkins, D F L

2003-01-01

Thin, optically semi-infinite films of amorphous TbFeCo and GdFeCo, suitable for magneto-optical recording, have been deposited by DC magnetron sputtering onto glass. Ellipsometric techniques have been used to determine the complex refractive index and complex magneto-optical parameter of the films in the wavelength range 400-900 nm, thus characterizing the materials. A review of the literature is presented and shows that the results for the TbFeCo films compare favourably with published results obtained from measurements conducted in situ, with the films protected with ZnS barrier layers. It is found that GdFeCo and TbFeCo are optically very similar, but magneto-optically the materials are quite different

Optical and magneto-optical characterization of TbFeCo and GdFeCo thin films for high-density recording

Energy Technology Data Exchange (ETDEWEB)

Hendren, W R [Department of Pure and Applied Physics, Queen' s University Belfast, Belfast BT7 1NN (United Kingdom); Atkinson, R [Department of Pure and Applied Physics, Queen' s University Belfast, Belfast BT7 1NN (United Kingdom); Pollard, R J [Department of Pure and Applied Physics, Queen' s University Belfast, Belfast BT7 1NN (United Kingdom); Salter, I W [Department of Pure and Applied Physics, Queen' s University Belfast, Belfast BT7 1NN (United Kingdom); Wright, C D [School of Engineering and Computer Science, University of Exeter, Exeter EX4 4QF (United Kingdom); Clegg, W W [CRIST, University of Plymouth, Plymouth PL4 8AA (United Kingdom); Jenkins, D F L [CRIST, University of Plymouth, Plymouth PL4 8AA (United Kingdom)

2003-03-12

Thin, optically semi-infinite films of amorphous TbFeCo and GdFeCo, suitable for magneto-optical recording, have been deposited by DC magnetron sputtering onto glass. Ellipsometric techniques have been used to determine the complex refractive index and complex magneto-optical parameter of the films in the wavelength range 400-900 nm, thus characterizing the materials. A review of the literature is presented and shows that the results for the TbFeCo films compare favourably with published results obtained from measurements conducted in situ, with the films protected with ZnS barrier layers. It is found that GdFeCo and TbFeCo are optically very similar, but magneto-optically the materials are quite different.

Regioselective C2 Oxidative Olefination of Indoles and Pyrroles through Cationic Rhodium(III)-Catalyzed C-H Bond Activation.

Science.gov (United States)

Li, Bin; Ma, Jianfeng; Xie, Weijia; Song, Haibin; Xu, Shansheng; Wang, Baiquan

2013-09-02

Be economic with your atoms! An efficient Rh-catalyzed oxidative olefination of indoles and pyrroles with broad substrate scope and tolerance is reported. The catalytic reaction proceeds with excellent regio- and stereoselectivity. The directing group N,N-dimethylcarbamoyl was crucial for the reaction and could be removed easily. Copyright © 2013 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim.

Growth and transport properties of thin Co-based Heusler films; Wachstum und Transporteigenschaften duenner Co-basierter Heusler-Filme

Energy Technology Data Exchange (ETDEWEB)

Schneider, Horst

2010-07-01

During this work, thin films of Co-based Heusler compounds were deposited under optimized conditions, and their structural, magnetic, and transport properties were investigated. The growth of the thin film samples was accomplished by two different methods. At first Co{sub 2}Cr{sub 0.6}Fe{sub 0.4}Al and Co{sub 2}FeSi were deposited by sputter deposition from stoichiometric targets. This is considered the standard technique for the preparation of thin Heusler films. Also for the compounds investigated here it resulted in samples with a high degree of L2{sub 1} ordering. An excess of Fe atoms on Si sites was discovered by a detailed X-ray analysis in conjunction with NMR spectroscopy. The choice of different substrates allowed the adjustment of the growth direction. On the other hand, bulk magnetometry revealed that these sputter deposited films exhibit only a reduced magnetic moment, which is an indication of a reduced spin asymmetry at the Fermi level. One source of this problem seems to be a high residual gas pressure, which leads to an increased sample contamination. To improve this situation, a pulsed laser deposition system was constructed and put into operation. The resulting film growth under ultra-high vacuum conditions led to a further improvement of the short-range crystallographic ordering and a clear enhancement of the magnetic properties. The additional use of a metallic buffer layer resulted in samples with a smooth surface. This opens the door for a number of further analytical experiments, such as tunneling spectroscopy or Brillouin light scattering. After this successful demonstration of this growth technique, an additional method for the flexible variation of the film stoichiometry was implemented. In this work, this method was successfully applied in the deposition of Co{sub 2}Mn{sub 1-x}Fe{sub x}Si films. All samples in this series show a high degree of atomic ordering. Their magnetization values are compatible with the Slater-Pauling rule for

A highly selective and wide range ammonia sensor—Nanostructured ZnO:Co thin film

International Nuclear Information System (INIS)

Mani, Ganesh Kumar; Rayappan, John Bosco Balaguru

2015-01-01

Graphical abstract: - Highlights: • Cobalt doped nanostructured ZnO thin films were spray deposited on glass substrates. • Co-doped ZnO film was highly selective towards ammonia than ethanol, methanol, etc. • The range of ammonia detection was improved significantly by doping cobalt in ZnO. - Abstract: Ammonia sensing characteristics of undoped and cobalt (Co)-doped nanostructured ZnO thin films were investigated. Polycrystalline nature with hexagonal wurtzite structure and high crystalline quality with dominant (0 0 2) plane orientation of Co-doped ZnO film were confirmed by the X-ray diffractogram. Scanning electron micrographs of the undoped film demonstrated the uniform deposition of sphere-shaped grains. But, smaller particles with no clear grain boundaries were observed for Co-doped ZnO thin film. Band gap values were found to be 3.26 eV and 3.22 eV for undoped and Co-doped ZnO thin films. Ammonia sensing characteristics of Co-doped ZnO film at room temperature were investigated in the concentration range of 15–1000 ppm. Variation in the sensing performances of Co-doped and pure ZnO thin films has been analyzed and compared

Structure and magnetization in CoPd thin films and nanocontacts

International Nuclear Information System (INIS)

Morgan, Caitlin; Schmalbuch, Klaus; García-Sánchez, Felipe; Schneider, Claus M.; Meyer, Carola

2013-01-01

We present results showing the structural and magnetic properties of MBE-grown extended films and nanostructured elements of various CoPd alloys. X-ray diffraction studies show that the thin films are polycrystalline, yet exhibit a strong preferential growth orientation along the (111) direction. Magnetic force microscopy and SQUID are used to gain an understanding of the magnetic behavior of the CoPd system with respect to competing anisotropy contributions, based on temperature-dependent SQUID data, collected between 4 and 300 K. The idea and potential implications of using CoPd as a contact material to achieve spin injection in carbon nanotube-based devices is discussed. - Highlights: ► In-plane magnetization of CoPd films increases with added Co content. ► Quasi single-domain nanostructures of Co 50 Pd 50 exhibit almost no OOP component. ► Nanostructures exhibit decrease in coercive field with initial temperature decrease. ► Magnetic behavior is influenced by the anti-FM oxide and magnetoelastic effect.

Preparation of thin {alpha}-particle sources using poly-pyrrole films functionalized by a chelating agent; Preparation de sources minces d'emetteurs alpha a l'aide de films de polypyrrole fonctionnalises par un ligand chelatant

Energy Technology Data Exchange (ETDEWEB)

Mariet, C. [CEA Saclay, INSTN, Institut National des Sciences et Techniques Nucleaires, 91 - Gif-sur-Yvette (France); Universite Pierre et Marie Curie, 75 - Paris (France)

2000-07-01

This work takes place in the scope of analysis of the {alpha}-particle emitting elements U, Pu and Am present in compound environmental matrix like sols and sediments. The samples diversity and above all the {alpha}-ray characteristics require the analyst to implement a sequence of chemical steps in which the more restricting is the actinides concentration in a uniform and thin layer en allowing an accurately measure of alpha activity. On this account, we studied a new technique for radioactive sources preparation based on tow steps: preparation of a thin film as source support; incorporation of radioactive elements by a chelating extraction mechanism. The thin films were obtained through electro-polymerization of pyrrole monomer functionalized by an chelating ligand able to extract actinides from concentrated acidic solutions. Polymerization conditions of this monomer were perfected, then obtained films were characterized from a physico-chemical point of view. We point out their extracting properties were comparable to (retention capacity, distribution coefficient) to those of usual ion-exchange resins. The underscore of uranyl and americium nitrate complexes formed in the thin layer allowed to calculate the extraction constants in case acid extraction is negligible. Thanks to this results, the values of the coefficients distribution D{sub U} and D{sub Am} could be provided for all nitric solutions in which acid extraction is negligible. Optimal actinides retention conditions in the polymer were defined and used to settle a protocol for plutonium analysis in environmental samples. (author)

Synthesis, nanostructure and magnetic properties of FeCo-reduced graphene oxide composite films by one-step electrodeposition

International Nuclear Information System (INIS)

Cao, Derang; Li, Hao; Wang, Zhenkun; Wei, Jinwu; Wang, Jianbo; Liu, Qingfang

2015-01-01

FeCo-reduced graphene oxide (FeCo-RGO) composite film was fabricated on indium tin oxide substrate using one-step electrodeposition method. Raman spectroscopy and field emission scanning electron microscope results show that the reduced graphene oxide is coprecipitated with the FeCo film. The energy-dispersive spectrometer results demonstrate that the atomic ratio of Fe/Co in FeCo-RGO composite film is larger than that of the FeCo film under the same fabrication condition. As a result, the FeCo-RGO composite film exhibits good soft magnetic properties and high-frequency properties as well as the FeCo film. The magnetic anisotropy field and saturation magnetization of FeCo-RGO composite film are increased when compared with FeCo film. Furthermore, the ferromagnetic resonance frequency is improved from 2.15 GHz for the FeCo film to 3.9 GHz for the FeCo-RGO composite film. - Highlights: • FeCo-reduced graphene oxide composite film was fabricated on indium tin oxide substrate. • One step electrodeposition method was used. • Good soft magnetic properties were exhibited by the composite films. • Increase of resonance frequency from 2.15 GHz for FeCo film to 3.9 GHz for composite film

Quantum interference effects in [Co/Bi]n thin films

Directory of Open Access Journals (Sweden)

Athanasopoulos P.

2014-07-01

Full Text Available Magnetoconductivity (MC, Δσ(Β, and Hall coefficient, RH(B, measurements have been performed in polycrystalline thin films of Bi(15nm, Bi(10nm/Co(1nm/Bi(10nm trilayer and [Co(0.7nm/Bi(2nm]10 multilayer, grown by magnetron scattering. The temperature dependence of RH(B curves reveal the existence of a second conduction channel below 250K, that can be assigned to surface states. MC measurements between ±0.4T show at 5K an interplay between weak-antilocalization (WAL in Bi and Bi/Co/Bi films and weal-localization (WL in [Co/Bi]10 multilayer.

Magnetic properties of Co-N films deposited by ECR nitrogen/argon plasma with DC negative-biased Co target

Energy Technology Data Exchange (ETDEWEB)

Li, H.; Zhang, Y.C.; Yang, K.; Liu, H.X.; Zhu, X.D., E-mail: xdzhu@ustc.edu.cn; Zhou, H.Y.

2017-06-01

Highlights: • A new method of synthesizing Co-N films containing Co{sub 4}N phase. • Tunable magnetic properties achieved in ECR plasma CVD. • The change of magnetic properties is related to atoms mobility on substrate and the concentration of active species in plasma vapor. - Abstract: By introducing DC negative-biased Co target in the Electron Cyclotron Resonance (ECR) nitrogen/argon plasma, the Co-N films containing Co{sub 4}N phase were synthesized on Si(100) substrate. Effects of processing parameters on magnetic properties of the films are investigated. It is found that magnetic properties of Co-N films vary with N{sub 2}/Ar flow ratio, substrate temperature, and target biasing voltage. The saturation magnetization M{sub s} decreased by increasing the N{sub 2}/Ar gas flow ratio or decreasing target biasing voltage, while the coercive field H{sub c} increased, which is ascribed to the variation of relative concentration for N or Co active species in plasma vapor. The magnetic properties present complex dependency with growth temperature, which is related to the atom mobility on the substrate affected by the growth temperature. This study exhibits a potential of ECR plasma chemical vapor deposition to synthesize the interstitial compounds and tune magnetic properties of films.

Voltage-Controlled Topotactic Phase Transition in Thin-Film SrCoOx Monitored by In Situ X-ray Diffraction.

Science.gov (United States)

Lu, Qiyang; Yildiz, Bilge

2016-02-10

Topotactic phase transition of functional oxides induced by changes in oxygen nonstoichiometry can largely alter multiple physical and chemical properties, including electrical conductivity, magnetic state, oxygen diffusivity, and electrocatalytic reactivity. For tuning these properties reversibly, feasible means to control oxygen nonstoichiometry-dependent phase transitions in functional oxides are needed. This paper describes the use of electrochemical potential to induce phase transition in strontium cobaltites, SrCoOx (SCO) between the brownmillerite (BM) phase, SrCoO₂.₅, and the perovskite (P) phase, SrCoO₃₋δ. To monitor the structural evolution of SCO, in situ X-ray diffraction (XRD) was performed on an electrochemical cell having (001) oriented thin-film SrCoOx as the working electrode on a single crystal (001) yttria-stabilized zirconia electrolyte in air. In order to change the effective pO₂ in SCO and trigger the phase transition from BM to P, external electrical biases of up to 200 mV were applied across the SCO film. The phase transition from BM to P phase could be triggered at a bias as low as 30 mV, corresponding to an effective pO₂ of 1 atm at 500 °C. The phase transition was fully reversible and the epitaxial film quality was maintained after reversible phase transitions. These results demonstrate the use of electrical bias to obtain fast and easily accessible switching between different phases as well as distinct physical and chemical properties of functional oxides as exemplified here for SCO.

Strapped Calix[4]pyrroles Bearing an 1,3-Indanedione at a β-Pyrrolic Position: Chemodosimeters for the Cyanide Anion

Science.gov (United States)

Kim, Sook-Hee; Hong, Seong-Jin; Yoo, Jaeduk; Kim, Sung Kuk; Sessler, Janathan L.; Lee, Chang-Hee

2014-01-01

A strapped calix[4]pyrrole bearing an 1,3-indanedione group at a β-pyrrolic position has been synthesized and studied as a ratiometric cyanide selective chemosensor. A concentration-dependent bleaching of the initial yellow color was observed upon addition of the cyanide anion. The bleaching, which was observed exclusively with the cyanide anion, occurred even in the presence of other anions. Spectroscopic studies provides support for a mechanistic interpretation wherein the cyanide anion forms a complex with the receptor (K = 2.78 × 104 M-1) through a fast equilibrium, which is followed by slow nucleophilic addition to the β-position of the 1,3-indanedione group. A minimum inhibitory effect from other anions was observed, a feature that could be beneficial in the selective sensing of the cyanide anion. PMID:19639968

5-Imino-3,4-diphenyl-1H-pyrrol-2-one

Science.gov (United States)

Bulatov, Evgeny; Chulkova, Tatiana; Haukka, Matti

2014-01-01

The title compound, C16H12N2O, exists in the crystalline state as the 5-imino-3,4-di­phenyl­-1H-pyrrol-2-one tautomer. The dihedral angles between the pyrrole and phenyl rings are 35.3 (2) and 55.3 (2)°. In the crystal, inversion dimers linked by pairs of N—H⋯N hydrogen bonds generate a graph-set motif of R 2 2(8) via N—H⋯N hydrogen bonds. PMID:24764881

5-Imino-3,4-diphenyl-1H-pyrrol-2-one

Directory of Open Access Journals (Sweden)

Evgeny Bulatov

2014-02-01

Full Text Available The title compound, C16H12N2O, exists in the crystalline state as the 5-imino-3,4-diphenyl-1H-pyrrol-2-one tautomer. The dihedral angles between the pyrrole and phenyl rings are 35.3 (2 and 55.3 (2°. In the crystal, inversion dimers linked by pairs of N—H...N hydrogen bonds generate a graph-set motif of R22(8 via N—H...N hydrogen bonds.

Oxoanion Recognition by Benzene-based Tripodal Pyrrolic Receptors

Energy Technology Data Exchange (ETDEWEB)

Bill, Nathan [University of Texas at Austin; Kim, Dae-Sik [University of Texas at Austin; Kim, Sung Kuk [University of Texas at Austin; Park, Jung Su [University of Texas at Austin; Lynch, Vincent M. [University of Texas at Austin; Young, Neil J [ORNL; Hay, Benjamin [ORNL; Yang, Youjun [University of Texas at Austin; Anslyn, Eric [University of Texas at Austin; Sessler, Jonathan L. [University of Texas

2012-01-01

Two new tripodal receptors based on pyrrole- and dipyrromethane-functionalised derivatives of a sterically geared precursor, 1,3,5-tris(aminomethyl)-2,4,6-triethylbenzene, are reported; these systems, compounds 1 and 2, display high affinity and selectivity for tetrahedral anionic guests, in particular dihydrogen phosphate, pyrophosphate and hydrogen sulphate, in acetonitrile as inferred from isothermal titration calorimetry measurements. Support for the anion-binding ability of these systems comes from theoretical calculations and a single-crystal X-ray diffraction structure of the 2:2 (host:guest) dihydrogen phosphate complex is obtained in the case of the pyrrole-based receptor system, 1. Keywords anion receptors, dihydrogen phosphate, hydrogen sulphate, X-ray structure, theoretical calculations.

Effect of non-electroactive additives on the early stage pyrrole electropolymerization on indium tin oxide electrodes

Energy Technology Data Exchange (ETDEWEB)

Castro-Beltran, A. [Facultad de Ingeniería Mecánica y Eléctrica, Universidad Autónoma de Nuevo León, Ave. Pedro de Alba s/n, Ciudad Universitaria, C.P. 66451 San Nicolás de los Garza, N.L. (Mexico); Centro de Innovación Investigación y Desarrollo en Ingeniería y Tecnología (CIIDIT), Universidad Autónoma de Nuevo León, PIIT-Monterrey C.P. 66600 Apodaca, N.L. (Mexico); Dominguez, C.; Bahena-Uribe, D. [Centro Investigación en Ingeniería y Ciencias Aplicadas (CIICAp), Universidad Autónoma del Estado de Morelos, Av. Universidad 1001, Col. Chamilpa, C.P. 62209 Cuernavaca, Mor. (Mexico); Sepulveda-Guzman, S., E-mail: selene.sepulvedagz@uanl.edu.mx [Facultad de Ingeniería Mecánica y Eléctrica, Universidad Autónoma de Nuevo León, Ave. Pedro de Alba s/n, Ciudad Universitaria, C.P. 66451 San Nicolás de los Garza, N.L. (Mexico); Centro de Innovación Investigación y Desarrollo en Ingeniería y Tecnología (CIIDIT), Universidad Autónoma de Nuevo León, PIIT-Monterrey C.P. 66600 Apodaca, N.L. (Mexico); Cruz-Silva, R. [Research Center for Exotic NanoCarbon, Shinshu University, 4-17-1 Wakasato, Nagano 380-8553 (Japan)

2014-09-01

The use of non-electroactive additives during electrodeposition of conducting polymers has long been used to modify the properties of deposited films. These additives can improve the adhesion, and not only change the morphology and deposition rate but also modify the chemical composition of the electrodeposited polymer. Several compounds have been used to modify deposition of polypyrrole; however, there is no systematic study of these compounds. In this work, we comparatively studied several water soluble chemical compounds, a cationic polymer, an anionic polymer, a cationic surfactant, and an anionic surfactant during potentiostatic electrodeposition of polypyrrole. In order to study the effect of these compounds on the interface, where the electrochemical polymerization takes place, we used electrochemical impedance spectroscopy. The morphology during the initial stage of growth was studied by atomic force microscopy, whereas the resulting polypyrrole films were observed by scanning electron microscopy. - Highlights: • Early-stage polymerization polypyrrole particles on indium tin oxide (ITO). • Anionic additives promote pyrrole oxidation and polypyrrole film growth on ITO. • Cationic polyelectrolyte promotes adhesion between ITO and polypyrrole film. • Non-electroactive additives strongly influence polypyrrole nucleation on ITO.

Properties of CoSb{sub 3} films grown by pulsed laser deposition

Energy Technology Data Exchange (ETDEWEB)

Christen, H M; Mandrus, D G; Norton, D P; Boatner, L A; Sales, B C

1997-07-01

Polycrystalline CoSb{sub 3} films were grown on a variety of electrically insulating substrates by pulsed laser ablation from a stoichiometric hot-pressed target. These films are fully crystallized in the skutterudite structure, and the grains exhibit a strongly preferred alignment of the cubic [310]-axis perpendicular to the substrate surface. The film quality is studied for different single-crystal substrates and as a function of growth temperature and background gas. Hall measurements show that the films are p-type semiconducting with a room-temperature carrier density of 3 x 10{sup 20} holes/cm{sup 3}. The Hall mobility is found to be 50 to 60 cm{sup 2}/Vs, which is high for such a heavily-doped material. The Seebeck coefficient and the resistivity are measured as a function of temperature and are compared to bulk measurements.

Structure and magnetization in CoPd thin films and nanocontacts

Energy Technology Data Exchange (ETDEWEB)

Morgan, Caitlin, E-mail: c.morgan@fz-juelich.de [Peter Gruenberg Institut, Forschungszentrum Juelich (Germany); JARA Juelich Aachen Research Alliance, 52425 Juelich (Germany); Schmalbuch, Klaus [JARA Juelich Aachen Research Alliance, 52425 Juelich (Germany); Physikalisches Institut, RWTH Aachen University, Otto-Blumenthal-Strasse, 52074 Aachen (Germany); Garcia-Sanchez, Felipe [Peter Gruenberg Institut, Forschungszentrum Juelich (Germany); JARA Juelich Aachen Research Alliance, 52425 Juelich (Germany); Schneider, Claus M. [Peter Gruenberg Institut, Forschungszentrum Juelich (Germany); JARA Juelich Aachen Research Alliance, 52425 Juelich (Germany); Fakultaet f. Physik and Center for Nanointegration Duisburg-Essen (CeNIDE), Universitaet Duisburg-Essen, D-47048 Duisburg (Germany); Meyer, Carola [Peter Gruenberg Institut, Forschungszentrum Juelich (Germany); JARA Juelich Aachen Research Alliance, 52425 Juelich (Germany)

2013-01-15

We present results showing the structural and magnetic properties of MBE-grown extended films and nanostructured elements of various CoPd alloys. X-ray diffraction studies show that the thin films are polycrystalline, yet exhibit a strong preferential growth orientation along the (111) direction. Magnetic force microscopy and SQUID are used to gain an understanding of the magnetic behavior of the CoPd system with respect to competing anisotropy contributions, based on temperature-dependent SQUID data, collected between 4 and 300 K. The idea and potential implications of using CoPd as a contact material to achieve spin injection in carbon nanotube-based devices is discussed. - Highlights: Black-Right-Pointing-Pointer In-plane magnetization of CoPd films increases with added Co content. Black-Right-Pointing-Pointer Quasi single-domain nanostructures of Co{sub 50}Pd{sub 50} exhibit almost no OOP component. Black-Right-Pointing-Pointer Nanostructures exhibit decrease in coercive field with initial temperature decrease. Black-Right-Pointing-Pointer Magnetic behavior is influenced by the anti-FM oxide and magnetoelastic effect.

A comparative investigation on structure and multiferroic properties of bismuth ferrite thin films by multielement co-doping

Energy Technology Data Exchange (ETDEWEB)

Dong, Guohua; Tan, Guoqiang, E-mail: tan3114@163.com; Luo, Yangyang; Liu, Wenlong; Xia, Ao; Ren, Huijun

2014-12-15

Highlights: • Multielement (Tb, Cr and Mn) co-doped BiFeO{sub 3} films were fabricated by CSD method. • Multielement co-doping induces a structural transition. • It is found effective to stabilize the valence of Fe ions at +3 by the strategy. • The co-doping at A/B-sites gives rise to the superior multiferroic properties. - Abstract: (Tb, Cr and Mn) multielement co-doped BiFeO{sub 3} (BTFCMO) thin films were prepared by the chemical solution deposition method on fluorine doped tin oxide (FTO) substrates. X-ray diffraction, Rietveld refinement and Raman analyses revealed that a phase transition from rhombohedral to triclinic structure occurs in the multielement co-doped BiFeO{sub 3} films. It is found that the doping is conducive to stabilizing the valence of Fe ions and reducing leakage current. In addition, the highly enhanced ferroelectric properties with a huge remanent polarization (2P{sub r}) of 239.6 μC/cm{sup 2} and a low coercive field (2E{sub c}) of 615.6 kV/cm are ascribed to the well film texture, the structure transition and the reduced leakage current by the co-doping. Moreover, the structure transition is the dominant factor resulting in the significant enhancement observed in magnetization (M{sub s} ∼ 10.5 emu/cm{sup 3}), owing to the collapse of the space-modulated spin structure. In this contribution, these results demonstrate that the multielement co-doping is in favor of the enhanced multiferroic properties of the BFO films for possible multifunctional applications.

Ammonia-treated porous carbon derived from ZIF-8 for enhanced CO{sub 2} adsorption

Energy Technology Data Exchange (ETDEWEB)

Ma, Xiancheng [School of Energy Science and Engineering, Central South University, Changsha 410083, Hunan (China); Li, Liqing, E-mail: liqingli@hotmail.com [School of Energy Science and Engineering, Central South University, Changsha 410083, Hunan (China); Wang, Shaobin [Department of Chemical Engineering, Curtin University, GPO Box U1987, Perth 6845, WA (Australia); Lu, Mingming [Department of Civil and Environmental Engineering, University of Cincinnati, Cincinnati, OH 45221 (United States); Li, Hailong; Ma, Weiwu [School of Energy Science and Engineering, Central South University, Changsha 410083, Hunan (China); Keener, Tim C. [Department of Civil and Environmental Engineering, University of Cincinnati, Cincinnati, OH 45221 (United States)

2016-04-30

Graphical abstract: The role of nitrogen species in increasing CO{sub 2} adsorption capacity has been explained with the mechanisms of base–acid interaction, as well as hydrogen bonds interaction. - Highlights: • A porous carbon (ZC) was prepared at 900 °C using ZIF-8 as a solid template for CO{sub 2} adsorption. • The ZC was further treated by ammonia functionalization to improve CO{sub 2} uptake. • The detailed interaction mechanism between N-containing groups and CO{sub 2} molecules is elucidated. - Abstract: A porous carbon (ZC) was prepared at 900 °C using zeolitic imidazolate framework-8 (ZIF-8) as a solid template for CO{sub 2} adsorption. The ZC was further treated by ammonia functionalization to improve CO{sub 2} uptake. The textural and surface characteristics of ZC samples were determined by X-ray diffraction (XRD), N{sub 2} adsorption, Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS). It was revealed that ammonia treatment at 600 °C considerably enhanced the specific surface area and N-content of ZC. However, the pyrrolic-N group was decreased, yet the pyridinic-N group was increased with an increased temperature. The pyrrolic-N significantly enhanced CO{sub 2} adsorption. The ammonia treatment, on the one hand, increases the alkalinity of ZC sample and the base–acid interaction between N-containing functional groups with CO{sub 2}. On the other hand, the ammonia treatment increased pyrrolic-N group (NH) into carbon surface facilitating the hydrogen-bonding interactions between proton of pyrrolic-N and CO{sub 2} molecules.

Magnetism and magnetoresistance from different origins in Co/ZnO:Al granular films

Energy Technology Data Exchange (ETDEWEB)

Quan, Zhiyong, E-mail: quanzy@sxnu.edu.cn; Liu, Xia; Song, Zhilin; Xu, Xiaohong, E-mail: xuxh@dns.sxnu.edu.cn

2016-12-01

Co/ZnO:Al granular films were made on glass substrates by sequential magnetron sputter deposition of ultrathin Co layer and ZnO:Al layer at room temperature. The as-deposited films consist of superparamagnetic Co particles dispersed in ZnO:Al (~2% Al) semiconductor matrix. Distinguished magnetoresistance effect at room temperature was obtained in the as-deposited films, which obviously reduced after annealing due to the growth of Co particles. The size of important magnetic particles was analyzed by Langevin function for hysteresis loops and magnetoresistance curves at room temperature. It was found that small magnetic particle contribute to magnetoresistance behavior and large particles dominate the room temperature magnetism in Co/ZnO:Al granular films.

Remarkable strain-induced magnetic anisotropy in epitaxial Co2MnGa (0 0 1) films

International Nuclear Information System (INIS)

Pechan, Michael J.; Yu, Chengtao; Carr, David; Palmstroem, Chris J.

2005-01-01

Remarkably large, strain-induced anisotropy is observed in the thin-film Heusler alloy Co 2 MnGa. 30 nm Co 2 MnGa (0 0 1) films have been epitaxially grown on different interlayers/substrates with varied strain, and investigated with ferromagnetic resonance. The film grown on ErAs/InGaAs/InP experiences tension strain, resulting in an out-of-plane strain-induced anisotropy (∼1.1x10 6 erg/cm 3 ) adding to the effects of shape anisotropy. In contrast, the film grown on ScErAs/GaAs, experiences a compression strain, resulting in an out-of-plane strain-induced anisotropy (∼3.3x10 6 erg/cm 3 ) which almost totally cancels the effects of shape anisotropy, thus rendering the film virtually isotropic. This results in the formation of stripe domains in remanence. In addition, small, but well-defined 2-fold and 4-fold in-plane anisotropy coexist in each sample with weak, but interesting strain dependence. Transport measurement shows small (<1%) magnetoresistance effects in the compression film, but negligible magnetoresistance in the relaxed and tension strained samples

Rhodium(III)-catalyzed [3+2] annulation of 5-aryl-2,3-dihydro-1H-pyrroles with internal alkynes through C(sp²)-H/alkene functionalization.

Science.gov (United States)

Zhou, Ming-Bo; Pi, Rui; Hu, Ming; Yang, Yuan; Song, Ren-Jie; Xia, Yuanzhi; Li, Jin-Heng

2014-10-13

This study describes a new rhodium(III)-catalyzed [3+2] annulation of 5-aryl-2,3-dihydro-1H-pyrroles with internal alkynes using a Cu(OAc)2 oxidant for building a spirocyclic ring system, which includes the functionalization of an aryl C(sp(2))-H bond and addition/protonolysis of an alkene C=C bond. This method is applicable to a wide range of 5-aryl-2,3-dihydro-1H-pyrroles and internal alkynes, and results in the assembly of the spiro[indene-1,2'-pyrrolidine] architectures in good yields with excellent regioselectivities. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Electroplated Fe-Co-Ni films prepared in ammonium-chloride-based plating baths

Science.gov (United States)

Yanai, T.; Koda, K.; Kaji, J.; Aramaki, H.; Eguchi, K.; Takashima, K.; Nakano, M.; Fukunaga, H.

2018-05-01

We electroplated Fe-Co-Ni films in ammonium-chloride-based plating baths, and investigated the effect of the Co content on the magnetic properties and the structural ones of the as-plated films. The coercivity increased abruptly when the Co content become more than 60 at.%. As the rough surfaces were observed in the high Co content region, we considered that degradation of the surface is a factor of the abrupt increase in the coercivity. From the XRD analysis, we found that another factor of the abrupt increase is fcc-bcc phase transformation, and concluded that we need to keep the fcc structure to obtain Fe-Co-Ni films with low coercivity.

Resistance switching in epitaxial SrCoO{sub x} thin films

Energy Technology Data Exchange (ETDEWEB)

Tambunan, Octolia T.; Parwanta, Kadek J.; Acharya, Susant K.; Lee, Bo Wha; Jung, Chang Uk, E-mail: cu-jung@hufs.ac.kr [Department of Physics, Hankuk University of Foreign Studies, Yongin 449-791 (Korea, Republic of); Kim, Yeon Soo; Park, Bae Ho [Division of Quantum Phases and Devices, Department of Physics, Konkuk University, Seoul 143-791 (Korea, Republic of); Jeong, Huiseong; Park, Ji-Yong [Department of Physics and Division of Energy System Research, Ajou University, Suwon 443-749 (Korea, Republic of); Cho, Myung Rae; Park, Yun Daniel [Department of Physics and Astronomy and Center for Subwavelength Optics, Seoul National University, Seoul 151-747 (Korea, Republic of); Choi, Woo Seok [Department of Physics, Sungkyunkwan University, Suwon 440-746 (Korea, Republic of); Kim, Dong-Wook [Department of Physics, Ewha Womans University, Seoul 120-750 (Korea, Republic of); Jin, Hyunwoo; Lee, Suyoun [Electronic Materials Research Center, Korea Institute of Science and Technology, Seoul 136-791 (Korea, Republic of); Song, Seul Ji; Kang, Sung-Jin; Kim, Miyoung; Hwang, Cheol Seong [Department of Material Science and Engineering, Seoul National University, Seoul 151-747 (Korea, Republic of)

2014-08-11

We observed bipolar switching behavior from an epitaxial strontium cobaltite film grown on a SrTiO{sub 3} (001) substrate. The crystal structure of strontium cobaltite has been known to undergo topotactic phase transformation between two distinct phases: insulating brownmillerite (SrCoO{sub 2.5}) and conducting perovskite (SrCoO{sub 3−δ}) depending on the oxygen content. The current–voltage characteristics of the strontium cobaltite film showed that it could have a reversible insulator-to-metal transition triggered by electrical bias voltage. We propose that the resistance switching in the SrCoO{sub x} thin film could be related to the topotactic phase transformation and the peculiar structure of SrCoO{sub 2.5}.

Hydroquinone–pyrrole dyads with varied linkers

Directory of Open Access Journals (Sweden)

Hao Huang

2016-01-01

Full Text Available A series of pyrroles functionalized in the 3-position with p-dimethoxybenzene via various linkers (CH2, CH2CH2, CH=CH, C≡C has been synthesized. Their electronic properties have been deduced from 1H NMR, 13C NMR, and UV–vis spectra to detect possible interactions between the two aromatic subunits. The extent of conjugation between the subunits is largely controlled by the nature of the linker, with the largest conjugation found with the trans-ethene linker and the weakest with the aliphatic linkers. DFT calculations revealed substantial changes in the HOMO–LUMO gap that correlated with the extent of conjugation found experimentally. The results of this work are expected to open up for use of the investigated compounds as components of redox-active materials in sustainable, organic electrical energy storage devices.

Electrocatalytic properties of monometallic and bimetallic nanoparticles-incorporated polypyrrole films for electro-oxidation of methanol

Energy Technology Data Exchange (ETDEWEB)

Selvaraj, V.; Alagar, M. [Department of Chemical Engineering, Alagappa College of Technology, Anna University, Chennai 600025 (India); Hamerton, I. [Chemistry Division, School of Biomedical and Molecular Sciences, University of Surrey, Guildford, Surrey GU2 7XH (United Kingdom)

2006-10-06

Oxidative electrochemical polymerization of pyrrole at indium-doped tin oxide (ITO) is accomplished from a neat monomer solution with a supporting electrolyte (0.3M n-tetrabutyl ammonium tetrafluoroborate) by multiple-scan cyclic voltammetry. Polypyrrole (Ppy) films containing nanometer-sized platinum and Pt/Pd bimetallic particles are electro-synthesized on ITO glass plates by voltammetric cycling between -0.1 and +1V (versus Ag/AgCl/3M NaCl). The electrocatalytic oxidation of methanol on the nanoparticle-modified polypyrrole films is studied by means of electrochemical techniques. The modified electrode exhibits significant eletrocatalytic activity for methanol oxidation. The enhanced electrocatalytic activities may be due to the uniform dispersion of nanoparticles in the polypyrrole film and a synergistic effect of the highly-dispersed metal particles so that the polypyrrole film reduces electrode poisoning by adsorbed CO species. The monometallic (Pt) and bimetallic (Pt/Pd) nanoparticles are uniformly dispersed in polypyrrole matrixes, as confirmed by scanning electron microscopic and atomic force microscopic analysis. Energy dispersive X-ray analysis is used to characterize the composition of metal present in the nanoparticle-modified electrodes. (author)

Preparation and Surface Analysis of PPY/SDBS Films on Aluminum Substrates

Directory of Open Access Journals (Sweden)

Lisete C. Scienza

2001-09-01

Full Text Available Polypyrrole films were generated on high purity aluminum substrates under anodic polarization from aqueous electrolytes comprised of pyrrole and sodium dodecylbenzene sulfonate. The methods employed to characterize the polymer films included scanning electron microscopy, Fourier-transform infrared and X-photoelectron spectroscopy and X-ray diffraction. PPY/SDBS films revealed nodular morphology with occasional appearing of "dendrites", high level of protonation, excess of counter-anions ([S]/[N] > [N+]/[N] and high degrees of disorder.

Superconductivity of a Sn film controlled by an array of Co nanowires

Science.gov (United States)

Wei, Z.; Ye, Z.; Rathnayaka, K. D. D.; Lyuksyutov, I. F.; Wu, W.; Naugle, D. G.

2012-09-01

Superconducting properties of a hybrid structure composed of ferromagnetic Co nanowire arrays and a superconducting Sn film have been investigated. Ordered Co nanowires arrays with 60 nm, 150 nm and 200 nm diameter were electroplated into the pores of self organized Anodic Aluminum Oxide (AAO) membranes. Hysteretic dependence of the Sn film superconducting properties on applied magnetic field and critical current enhancement at moderate fields has been observed. This behavior strongly depends on the ratio of the Sn film thickness to the Co nanowire diameter.

Superconductivity of a Sn film controlled by an array of Co nanowires

International Nuclear Information System (INIS)

Wei, Z.; Ye, Z.; Rathnayaka, K.D.D.; Lyuksyutov, I.F.; Wu, W.; Naugle, D.G.

2012-01-01

Superconducting properties of a hybrid structure composed of ferromagnetic Co nanowire arrays and a superconducting Sn film have been investigated. Ordered Co nanowires arrays with 60 nm, 150 nm and 200 nm diameter were electroplated into the pores of self organized Anodic Aluminum Oxide (AAO) membranes. Hysteretic dependence of the Sn film superconducting properties on applied magnetic field and critical current enhancement at moderate fields has been observed. This behavior strongly depends on the ratio of the Sn film thickness to the Co nanowire diameter.

The role of electrolyte pH on phase evolution and magnetic properties of CoFeW codeposited films

International Nuclear Information System (INIS)

Ghaferi, Z.; Sharafi, S.; Bahrololoom, M.E.

2016-01-01

Highlights: • Deposition tends to anomalous-induced fashion at higher pH values. • The structure of the coatings depend on electrolyte pH effectively. • Grain size of two-phase structure films is lower than single-phase solid solutions. • Coercivity of the coatings changed by tungsten content and surface defects. • The highest pH value produced coating with superior magnetic behaviour. - Abstract: In this research, nanocrystalline Co–Fe–W alloy coatings were electrodeposited from a citrate-borate bath. The influence of electrolyte pH on the morphology, microstructure and magnetic properties of these films was also studied. By increasing pH value, the amount of iron content increased from 30 to 55 wt.% which indicates anomalous fashion at higher pH electrolytes. X-ray diffraction patterns showed that the structure of these films depend on electrolyte pH effectively. However, two-phase structure coatings showed smaller average grain size compared with one- phase solid solutions. Vibrating sample magnetometer measurements indicated that the coercivity of the coatings was in the range of 21–76 Oe. However, the highest pH value produced coating with superior magnetic behaviour. Microhardness of the coatings reached its maximum value at about 260HV which is referred to the highest tungsten content.

Thin, Conductive, Pyrrolyc film production for radioactive sources backings

International Nuclear Information System (INIS)

Rodriguez, L.; Arcos, J.M. los

1993-01-01

A procedure for electro polymerization of pyrrole has been set up in order to produce thin, (> 15 μg/cm2) homogeneous (thickness variation < 2%) films, with no need for additional metallization to be used as backings of radioactive sources, having 10-0,4 Kfl/sample, for 35-70 μg/cm . The experimental equipment, reagent and procedure utilized is described as well as the characterization of Pyrrolyc films produced. (Author) 28 refs

Transparent conducting thin films by co-sputtering of ZnO-ITO targets

Energy Technology Data Exchange (ETDEWEB)

Carreras, Paz; Antony, Aldrin; Roldan, Ruben; Nos, Oriol; Frigeri, Paolo Antonio; Asensi, Jose Miguel; Bertomeu, Joan [Grup d' Energia Solar, Universitat de Barcelona (Spain)

2010-04-15

Transparent and conductive Zn-In-Sn-O (ZITO) amorphous thin films have been deposited at room temperature by the rf magnetron co-sputtering of ITO and ZnO targets. Co-sputtering gives the possibility to deposit multicomponent oxide thin films with different compositions by varying the power to one of the targets. In order to make ZITO films with different Zn content, a constant rf power of 50 W was used for the ITO target, where as the rf power to ZnO target was varied from 25 W to 150 W. The as deposited films showed an increase in Zn content ratio from 17 to 67% as the power to ZnO target was increased from 25 to 150 W. The structural, electrical and optical properties of the as deposited films are reported. The films showed an average transmittance over 80% in the visible wavelength range. The electrical resistivity and optical band gap of the ZITO films were found to depend on the Zn content in the film. The ZITO films deposited at room temperature with lower Zn content ratios showed better optical transmission and electrical properties compared to ITO film. (copyright 2010 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Pulsed laser deposition of nanostructured Co-B-O thin films as efficient catalyst for hydrogen production

Energy Technology Data Exchange (ETDEWEB)

Jadhav, H., E-mail: jadhav.hs2013@gmail.com [Laser and Plasma Technology Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400085 (India); Singh, A.K. [Laser and Plasma Technology Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400085 (India); Patel, N.; Fernandes, R.; Gupta, S.; Kothari, D.C. [Department of Physics and National Centre for Nanosciences & Nanotechnology, University of Mumbai, Vidyanagari, Santacruz (E), Mumbai 400098 (India); Miotello, A. [Dipartimento di Fisica, Università degli Studi di Trento, I-38123 Povo, Trento (Italy); Sinha, S. [Laser and Plasma Technology Division, Bhabha Atomic Research Centre, Trombay, Mumbai 400085 (India)

2016-11-30

Highlights: • Pulsed laser deposition was used to deposit Co-B-O film nanocatalyst. • Co-B-O NPs are well separated, stable and immobilized on film surface. • Catalytic H{sub 2} production was studied by hydrolysis of Sodium Borohydride. • Four times higher H{sub 2} production rate was recorded for Co-B-O film than Co-B-O powder. • High particle density, polycrystalline nature and good stability against agglomeration of Co NPs. - Abstract: Nanoparticles assembled Co-B-O thin film catalysts were synthesized by pulsed laser deposition (PLD) technique for hydrolysis of Sodium Borohydride (SBH). Surface morphology of the deposited films was investigated using SEM and TEM, while compositional analysis was studied using XPS. Structural properties of Co-B-O films were examined using XRD and HRTEM. Laser process is able to produce well separated and immobilized Co-B-O NPs on the film surface which act as active centers leading to superior catalytic activity producing hydrogen at a significantly higher rate as compared to bulk powder. Co-B-O thin film catalyst produces hydrogen at a maximum rate of ∼4400 ml min{sup −1} g{sup −1} of catalyst, which is four times higher than powder catalyst. PLD parameters such as laser fluence and substrate-target distance were varied during deposition in order to understand the role of size and density of the immobilized Co-B-O NPs in the catalytic process. Films deposited at 3–5 cm substrate-target distance showed better performance than that deposited at 6 cm, mainly on account of the higher density of active Co-B-O NPs on the films surface. Features such as high particle density, polycrystalline nature of Co NPs and good stability against agglomeration mainly contribute towards the superior catalytic activity of Co-B-O films deposited by PLD.

Solid-state synthesis, structural and magnetic properties of CoPd films

Science.gov (United States)

Myagkov, V. G.; Bykova, L. E.; Zhigalov, V. S.; Tambasov, I. A.; Bondarenko, G. N.; Matsynin, A. A.; Rybakova, A. N.

2015-05-01

The results of the investigation of the structural and magnetic properties of CoPd films with equiatomic composition have been presented. The films have been synthesized by vacuum annealing of polycrystalline Pd/Co and epitaxial Pd/α-Co(110) and Pd/β-Co(001) bilayer samples. It has been shown that, for all samples, the annealing to 400°C does not lead to the mixing of layers and the formation of compounds. A further increase in the annealing temperature results in the formation of a disordered CoPd phase at the Pd/Co interface, which is fully completed after annealing at 650°C. The epitaxial relationships between the disordered CoPd phase and the MgO(001) substrate are determined as follows: CoPd(110)<

A role of nanotube dangling pyrrole and oxygen functions in the electrochemical synthesis of polypyrrole/MWCNTs hybrid materials

International Nuclear Information System (INIS)

Krukiewicz, Katarzyna; Herman, Artur P.; Turczyn, Roman; Szymańska, Katarzyna; Koziol, Krzysztof K.K.; Boncel, Sławomir; Zak, Jerzy K.

2014-01-01

Highlights: • The effect of MWCNT functionalization on properties of PPy composites was explained. • The behavior of pristine, pyrrole-modified and oxidized MWCNT was explained. • Functionalization of MWCNT improved their dispersibility and processability. • Different mechanisms of (f-)MWCNT incorporation into PPy composites were explained. • Orientation of growing PPy chains was tailored through the addition of (f-)MWCNT. - Abstract: The effect of the functionalization of multi-walled carbon nanotubes (MWCNTs) on the process of electrochemical co-deposition of MWCNTs and polypyrrole (PPy), as well as the morphology of obtained composites have been demonstrated. As the nanotube components of the hybrids, three types of MWCNT were used, namely c-CVD derived (pristine) MWCNTs, their oxidized counterparts MWCNT-Ox and pyrrole-modified MWCNT-Py. The stability of pristine and functionalized MWCNTs (f-MWCNT) dispersions in tetrahydrofuran and water was studied together with the description of the process of formation PPy/(f-)MWCNT hybrid materials via electrochemical co-deposition. The structural and morphological properties of the hybrids were characterized by Raman spectroscopy, scanning electron microscopy and atomic force microscopy revealing substantial differences among hybrid materials in their surface morphology and the influence of MWCNT functionalization on the orientation of growing PPy chains

A role of nanotube dangling pyrrole and oxygen functions in the electrochemical synthesis of polypyrrole/MWCNTs hybrid materials

Energy Technology Data Exchange (ETDEWEB)

Krukiewicz, Katarzyna, E-mail: katarzyna.krukiewicz@polsl.pl [Department of Physical Chemistry and Technology of Polymers, Silesian University of Technology, Strzody 9, 44-100 Gliwice (Poland); Herman, Artur P., E-mail: artur.herman@polsl.pl [Department of Organic Chemistry, Bioorganic Chemistry and Biotechnology, Silesian University of Technology, Krzywoustego 4, Gliwice 44-100 (Poland); Turczyn, Roman, E-mail: roman.turczyn@polsl.pl [Department of Physical Chemistry and Technology of Polymers, Silesian University of Technology, Strzody 9, 44-100 Gliwice (Poland); Szymańska, Katarzyna, E-mail: katarzyna.szymanska@polsl.pl [Department of Chemical and Process Engineering, Silesian University of Technology, Strzody 7, 44-100 Gliwice (Poland); Koziol, Krzysztof K.K., E-mail: kk292@cam.ac.uk [Department of Materials Science and Metallurgy, University of Cambridge, 27 Charles Babbage Road, Cambridge CB3 0FS (United Kingdom); Boncel, Sławomir, E-mail: slawomir.boncel@polsl.pl [Department of Organic Chemistry, Bioorganic Chemistry and Biotechnology, Silesian University of Technology, Krzywoustego 4, Gliwice 44-100 (Poland); Zak, Jerzy K., E-mail: jerzy.zak@polsl.pl [Department of Physical Chemistry and Technology of Polymers, Silesian University of Technology, Strzody 9, 44-100 Gliwice (Poland)

2014-10-30

Highlights: • The effect of MWCNT functionalization on properties of PPy composites was explained. • The behavior of pristine, pyrrole-modified and oxidized MWCNT was explained. • Functionalization of MWCNT improved their dispersibility and processability. • Different mechanisms of (f-)MWCNT incorporation into PPy composites were explained. • Orientation of growing PPy chains was tailored through the addition of (f-)MWCNT. - Abstract: The effect of the functionalization of multi-walled carbon nanotubes (MWCNTs) on the process of electrochemical co-deposition of MWCNTs and polypyrrole (PPy), as well as the morphology of obtained composites have been demonstrated. As the nanotube components of the hybrids, three types of MWCNT were used, namely c-CVD derived (pristine) MWCNTs, their oxidized counterparts MWCNT-Ox and pyrrole-modified MWCNT-Py. The stability of pristine and functionalized MWCNTs (f-MWCNT) dispersions in tetrahydrofuran and water was studied together with the description of the process of formation PPy/(f-)MWCNT hybrid materials via electrochemical co-deposition. The structural and morphological properties of the hybrids were characterized by Raman spectroscopy, scanning electron microscopy and atomic force microscopy revealing substantial differences among hybrid materials in their surface morphology and the influence of MWCNT functionalization on the orientation of growing PPy chains.

A „Hybrid“ Thin-Film pH Sensor with Integrated Thick-Film Reference

OpenAIRE

Simonis, Anette; Krings, Thomas; Lüth, Hans; Wang, Joseph; Schöning, Michael J.

2001-01-01

A reference electrode fabricated by means of thick-film technique is deposited onto a silicon substrate and combined with a thin-film pH sensor to a “hybrid†chip system. To evaluate the suitability of this combination, first investigations were carried out. The characteristics of the thin-film pH sensor were studied towards the thick-film Ag/AgCl reference electrode. Measurements were performed in the capacitance/voltage (C/V) and constant capacitance (Concap) mode for different pH ...

Carbon isotope exchange between gaseous CO2 and thin solution films: Artificial cave experiments and a complete diffusion-reaction model

Science.gov (United States)

Hansen, Maximilian; Scholz, Denis; Froeschmann, Marie-Louise; Schöne, Bernd R.; Spötl, Christoph

2017-08-01

Speleothem stable carbon isotope (δ13C) records provide important paleoclimate and paleo-environmental information. However, the interpretation of these records in terms of past climate or environmental change remains challenging because of various processes affecting the δ13C signals. A process that has only been sparsely discussed so far is carbon isotope exchange between the gaseous CO2 of the cave atmosphere and the dissolved inorganic carbon (DIC) contained in the thin solution film on the speleothem, which may be particularly important for strongly ventilated caves. Here we present a novel, complete reaction diffusion model describing carbon isotope exchange between gaseous CO2 and the DIC in thin solution films. The model considers all parameters affecting carbon isotope exchange, such as diffusion into, out of and within the film, the chemical reactions occurring within the film as well as the dependence of diffusion and the reaction rates on isotopic mass and temperature. To verify the model, we conducted laboratory experiments under completely controlled, cave-analogue conditions at three different temperatures (10, 20, 30 °C). We exposed thin (≈0.1 mm) films of a NaHCO3 solution with four different concentrations (1, 2, 5 and 10 mmol/l, respectively) to a nitrogen atmosphere containing a specific amount of CO2 (1000 and 3000 ppmV). The experimentally observed temporal evolution of the pH and δ13C values of the DIC is in good agreement with the model predictions. The carbon isotope exchange times in our experiments range from ca. 200 to ca. 16,000 s and strongly depend on temperature, film thickness, atmospheric pCO2 and the concentration of DIC. For low pCO2 (between 500 and 1000 ppmV, as for strongly ventilated caves), our time constants are substantially lower than those derived in a previous study, suggesting a potentially stronger influence of carbon isotope exchange on speleothem δ13C values. However, this process should only have an

Microstructure and magnetic properties of Co-doped ZnO films deposited by gas flow sputtering

Energy Technology Data Exchange (ETDEWEB)

Sakuma, H., E-mail: hsakuma@cc.utsunomiya-u.ac.jp [Research Division of Functional Materials Design, Utsunomiya University, 7-1-2 Yoto, Utsunomiya 321-8585 (Japan); Watanabe, Y. [Research Division of Functional Materials Design, Utsunomiya University, 7-1-2 Yoto, Utsunomiya 321-8585 (Japan); Aramaki, K.; Yun, K.S. [Sony Chemical and Information Device Corporation, 1078 Kamiishikawa, Kanuma 322-8503 (Japan); Ishii, K. [Research Division of Functional Materials Design, Utsunomiya University, 7-1-2 Yoto, Utsunomiya 321-8585 (Japan); Ikeda, Y.; Kondo, H. [Sony Chemical and Information Device Corporation, 1078 Kamiishikawa, Kanuma 322-8503 (Japan)

2010-10-15

Co-doped ZnO films with a Co concentration of 8-20 at.% were fabricated using the low-energy process of gas flow sputtering. X-ray diffraction, X-ray photoelectron spectroscopy, and optical absorption measurements revealed that the Co ions replace Zn ions in the ZnO matrix and that the Co ions have an oxidation state of 2+. The magnetic properties of the film depend on the Co concentration. The plots of magnetization and inverse susceptibility vs. temperature indicate that the film with a high Co concentration (20 at.%) contains a ferromagnetic component, while that with a low Co concentration (8 at.%) contains an antiferromagnetic component. The film with an intermediate Co concentration (10 at.%) contains a ferromagnetic component with a low Curie temperature. Hysteresis was not found in magnetization curves for all the samples, including the sample at 5 K. The films exhibited a high resistivity of 4 x 10{sup 7}-2 x 10{sup 8} {Omega} cm at room temperature, and carrier-mediated magnetism is not likely to be applicable for the mechanisms of the magnetism in the films.

Microstructure and magnetic properties of Co-doped ZnO films deposited by gas flow sputtering

International Nuclear Information System (INIS)

Sakuma, H.; Watanabe, Y.; Aramaki, K.; Yun, K.S.; Ishii, K.; Ikeda, Y.; Kondo, H.

2010-01-01

Co-doped ZnO films with a Co concentration of 8-20 at.% were fabricated using the low-energy process of gas flow sputtering. X-ray diffraction, X-ray photoelectron spectroscopy, and optical absorption measurements revealed that the Co ions replace Zn ions in the ZnO matrix and that the Co ions have an oxidation state of 2+. The magnetic properties of the film depend on the Co concentration. The plots of magnetization and inverse susceptibility vs. temperature indicate that the film with a high Co concentration (20 at.%) contains a ferromagnetic component, while that with a low Co concentration (8 at.%) contains an antiferromagnetic component. The film with an intermediate Co concentration (10 at.%) contains a ferromagnetic component with a low Curie temperature. Hysteresis was not found in magnetization curves for all the samples, including the sample at 5 K. The films exhibited a high resistivity of 4 x 10 7 -2 x 10 8 Ω cm at room temperature, and carrier-mediated magnetism is not likely to be applicable for the mechanisms of the magnetism in the films.

Preparation and structural characterization of FeCo epitaxial thin films on insulating single-crystal substrates

International Nuclear Information System (INIS)

Nishiyama, Tsutomu; Ohtake, Mitsuru; Futamoto, Masaaki; Kirino, Fumiyoshi

2010-01-01

FeCo epitaxial films were prepared on MgO(111), SrTiO 3 (111), and Al 2 O 3 (0001) single-crystal substrates by ultrahigh vacuum molecular beam epitaxy. The effects of insulating substrate material on the film growth process and the structures were investigated. FeCo(110) bcc films grow on MgO substrates with two type domains, Nishiyama-Wassermann (NW) and Kurdjumov-Sachs (KS) relationships. On the contrary, FeCo films grown on SrTiO 3 and Al 2 O 3 substrates include FeCo(111) bcc crystal in addition to the FeCo(110) bcc crystals with NW and KS relationships. The FeCo(111) bcc crystal consists of two type domains whose orientations are rotated around the film normal by 180 deg. each other. The out-of-plane and the in-plane lattice spacings of FeCo(110) bcc and FeCo(111) bcc crystals formed on the insulating substrates are in agreement with those of the bulk Fe 50 Co 50 (at. %) crystal with small errors ranging between +0.2% and +0.4%, showing that the strains in the epitaxial films are very small.

Rhodium enalcarbenoids: direct synthesis of indoles by rhodium(II)-catalyzed [4+2] benzannulation of pyrroles.

Science.gov (United States)

Dawande, Sudam Ganpat; Kanchupalli, Vinaykumar; Kalepu, Jagadeesh; Chennamsetti, Haribabu; Lad, Bapurao Sudam; Katukojvala, Sreenivas

2014-04-14

Disclosed herein is the design of an unprecedented electrophilic rhodium enalcarbenoid which results from rhodium(II)-catalyzed decomposition of a new class of enaldiazo compounds. The synthetic utility of these enalcarbenoids has been successfully demonstrated in the first transition-metal-catalyzed [4+2] benzannulation of pyrroles, thus leading to substituted indoles. The new benzannulation has been applied to the efficient synthesis of the natural product leiocarpone as well as a potent adipocyte fatty-acid binding protein inhibitor. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Non-conductive ferromagnetic carbon-coated (Co, Ni) metal/polystyrene nanocomposites films

Energy Technology Data Exchange (ETDEWEB)

Takacs, H., E-mail: helene.takacs@gmail.com [CEA, LETI, MINATEC Campus, Grenoble 38054 (France); LTM-CNRS-UJF, CEA, LETI, Minatec Campus, Grenoble 38054 (France); Viala, B.; Hermán, V. [CEA, LETI, MINATEC Campus, Grenoble 38054 (France); Tortai, J.-H. [LTM-CNRS-UJF, CEA, LETI, Minatec Campus, Grenoble 38054 (France); Duclairoir, F. [Université Grenoble Alpes, INAC, Grenoble 38054 (France); CEA, INAC, Grenoble 38054 (France)

2016-03-07

This article reports non-conductive ferromagnetic properties of metal/polymer nanocomposite films intended to be used for RF applications. The nanocomposite arrangement is unique showing a core double-shell structure of metal-carbon-polystyrene: M/C//P{sub 1}/P{sub 2}, where M = Co, Ni is the core material, C = graphene or carbon is the first shell acting as a protective layer against oxidation, P{sub 1} = pyrene-terminated polystyrene is the second shell for electrical insulation, and P{sub 2} = polystyrene is a supporting matrix (// indicates actual grafting). The nanocomposite formulation is briefly described, and the film deposition by spin-coating is detailed. Original spin-curves are reported and analyzed. One key outcome is the achievement of uniform and cohesive films at the wafer scale. Structural properties of films are thoroughly detailed, and weight and volume fractions of M/C are considered. Then, a comprehensive overview of DC magnetic and electrical properties is reported. A discussion follows on the magnetic softness of the nanocomposites vs. that of a single particle (theoretical) and the raw powder (experimental). Finally, unprecedented achievement of high magnetization (∼0.6 T) and ultra-high resistivity (∼10{sup 10 }μΩ cm) is shown. High magnetization comes from the preservation of the existing protective shell C, with no significant degradation on the particle net-moment, and high electrical insulation is ensured by adequate grafting of the secondary shell P{sub 1}. To conclude, the metal/polymer nanocomposites are situated in the landscape of soft ferromagnetic materials for RF applications (i.e., inductors and antennas), by means of two phase-diagrams, where they play a crucial role.

Magnetic, structural and electrical properties of ordered and disordered Co50Fe50 films

International Nuclear Information System (INIS)

Chen, Y.T.; Jen, S.U.; Yao, Y.D.; Wu, J.M.; Hwang, G.H.; Tsai, T.L.; Chang, Y.C.; Sun, A.C.

2006-01-01

Co 50 Fe 50 films with thickness varying from 100 to 500 A were deposited on a glass substrate by sputtering process, respectively. Two kinds of CoFe films were studied: one was the as-deposited film, and the other the annealed film. The annealing procedure was to keep the films at 400 deg. C for 5 h in a vacuum of 5x10 -6 mbar. From the X-ray study, we find that the as-deposited film prefers the CoFe(1 1 0) orientation. Moreover, the body-centered cubic (bcc) CoFe(1 1 0) line is split into two peaks: one corresponding to the ordered body-centered tetragonal (bct) phase, and the other, the disordered bcc phase. After annealing, the peak intensity of the ordered bct phase becomes much stronger, while that of the disordered bcc phase disappears. The annealing has also caused the ordered CoFe(2 0 0) line to appear. When the amount of the ordered bct phase in Co 50 Fe 50 is increased, the saturation magnetization (M s ) and coercivity (H c ) become larger, but the electrical resistivity (ρ) decreases. From the temperature coefficient of resistance (TCR) measurement, we learn that the bct grains in the CoFe film start to grow at temperature 82 deg. C

Bio-plastic (P-3HB-co-3HV) from Bacillus circulans (MTCC 8167) and its biodegradation.

Science.gov (United States)

Phukon, Pinkee; Saikia, Jyoti Prasad; Konwar, Bolin Kumar

2012-04-01

Polyhydroxyalkanoates (PHAs) are naturally occurring polyesters synthesized by bacteria for carbon and energy storage and it has commercial potential as bioplastic. The bacterial species Bacillus circulans MTCC 8167, isolated from crude oil contaminated soil, can efficiently produce medium chain length polyhydroxyalkanoates (P-3HB-co-3HV) from cheap carbon sources like dextrose. The molecular mass of P-3HB-co-3HV was reported as 5.1×10(4)Da with polydispersity index of 1.21 by gel permeation chromatography. In the present investigation different bacteria and fungi species were used for testing the biodegradability of the extracted polymer. The FTIR spectra of the biodegraded PHBV film showed a decrease in the peak from 1735 cm(-1) (untreated film) to 1675 cm(-1), and disappearance of a peak present in the control at 2922 cm(-1) indicating the breakdown of ester (>C=O) or O-R group and -C=H bond, respectively. From biodegradability testing, the tested microorganisms were found to have decisive contribution to the biodegradation of P-3HB-co-3HV polymer. Copyright © 2011 Elsevier B.V. All rights reserved.

Ordering phenomena in FeCo-films and Fe/Cr-multilayers: an X-ray and neutron scattering study

Energy Technology Data Exchange (ETDEWEB)

Nickel, B.

2001-07-01

The following topics are covered: critical phenomena in thin films, critical adsorption, finite size scaling, FeCo Ising model, kinematical scattering theory for thin films, FeCo thin films, growth and characterisation of single crystal FeCo thin films, X-ray study of ordering in FeCo films, antiferromagnetic coupling in Fe/Cr multilayers, neutron scattering on Fe/Cr multilayers (WL)

Development of luminescent pH sensor films for monitoring bacterial growth through tissue.

Science.gov (United States)

Wang, Fenglin; Raval, Yash; Chen, Hongyu; Tzeng, Tzuen-Rong J; DesJardins, John D; Anker, Jeffrey N

2014-02-01

Although implanted medical devices (IMDs) offer many benefits, they are susceptible to bacterial colonization and infections. Such infections are difficult to treat because bacteria could form biofilms on the implant surface, which reduce antibiotics penetration and generate local dormant regions with low pH and low oxygen. In addition, these infections are hard to detect early because biofilms are often localized on the surface. Herein, an optical sensor film is developed to detect local acidosis on an implanted surface. The film contains both upconverting particles (UCPs) that serve as a light source and a pH indicator that alters the luminescence spectrum. When irradiated with 980 nm light, the UCPs produce deeply penetrating red light emission, while generating negligible autofluorescence in the tissue. The basic form of the pH indicator absorbs more of upconversion luminescence at 661 nm than at 671 nm and consequently the spectral ratio indicates pH. Implanting this pH sensor film beneath 6-7 mm of porcine tissue does not substantially affect the calibration curve because the peaks are closely spaced. Furthermore, growth of Staphylococcus epidermidis on the sensor surface causes a local pH decrease that can be detected non-invasively through the tissue. Copyright © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Room temperature deposition of perpendicular magnetic anisotropic Co{sub 3}Pt thin films on glass substrate

Energy Technology Data Exchange (ETDEWEB)

Chen, Yu-Shen; Dai, Hong-Yu; Hsu, Yi-Wei [Department of Chemical Engineering and Materials Science, Yuan-Ze University, Chung-Li 32003, Taiwan (China); Ou, Sin-Liang, E-mail: slo@mail.dyu.edu.tw [Department of Materials Science and Engineering, Da-Yeh University, Changhua 51591, Taiwan (China); Chen, Shi-Wei [National Synchrotron Radiation Research Center (NSRRC), Hsinchu 300, Taiwan (China); Lu, Hsi-Chuan; Wang, Sea-Fue [Department of Materials and Mineral Resources Engineering, National Taipei University of Technology, Taipei 106, Taiwan (China); Sun, An-Cheng, E-mail: acsun@saturn.yzu.edu.tw [Department of Chemical Engineering and Materials Science, Yuan-Ze University, Chung-Li 32003, Taiwan (China)

2017-03-01

Co{sub 3}Pt alloy thin films were deposited on the glass substrate at room temperature (RT) and 300 °C, which showed high perpendicular magnetic anisotropy (PMA) and isotropy magnetic behaviors, respectively. Co{sub 3}Pt HCP (0002) planes grew along the substrate plane for the films deposited at RT. The easy axis [0001] was consequently vertical to the substrate surface and obtained the predominant PMA. Large magnetic domains and sharp boundary also supported high PMA in RT-deposited samples. On the other hand, the PMA was significantly decreased with increasing the deposition temperature from RT to 300 °C. Hard HCP(0002) and soft A1(111) co-existed in the film and the magnetic exchanged coupling between these two phases induced isotropy magnetic behavior. In addition, the various thicknesses (t) of the RT-deposited Co{sub 3}Pt films were deposited with different base pressures prior to sputtering. The Kerr rotation loops showed high PMA and out-of-plane squareness (S{sub ⊥}) of ~0.9 were found in low base pressure chamber. Within high base pressure chamber, Co{sub 3}Pt films just show magnetic isotropy behaviors. This study provides a fabrication method for the preparation of high PMA HCP-type Co{sub 3}Pt films on the glass substrate without any underlayer at RT. The results could be the base for future development of RT-deposited magnetic alloy thin film with high PMA. - Highlights: • Fabricated high perpendicular magnetic anisotropy Co{sub 3}Pt thin film on glass substrate. • Prepared HCP Co{sub 3}Pt thin film at room temperature. • The key to enhance the PMA of the Co{sub 3}Pt films. • Thinner film is good to fabricate PMA Co{sub 3}Pt thin films.

Framing and bias in CO2 capture and storage communication films: Reflections from a CO2 capture and storage research group.

Science.gov (United States)

Maynard, Carly M; Shackley, Simon

2017-03-01

There has been a growing trend towards incorporating short, educational films as part of research funding and project proposals. Researchers and developers in CO 2 capture and storage are using films to communicate outcomes, but such films can be influenced by experiences and values of the producers. We document the content and presentation of seven online CO 2 capture and storage films to determine how framing occurs and its influence on the tone of films. The core frame presents CO 2 capture and storage as a potential solution to an imminent crisis in climatic warming and lack of a sustainable energy supply. Three subsidiary frames represent CO 2 capture and storage as (1) the only option, (2) a partial option or (3) a scientific curiosity. The results demonstrate that an understanding of the nuanced explicit and implicit messages portrayed by films is essential both for effective framing according to one's intention and for wider public understanding of a field.

Development of Anti-Insect Microencapsulated Polypropylene Films Using a Large Scale Film Coating System.

Science.gov (United States)

Song, Ah Young; Choi, Ha Young; Lee, Eun Song; Han, Jaejoon; Min, Sea C

2018-04-01

Films containing microencapsulated cinnamon oil (CO) were developed using a large-scale production system to protect against the Indian meal moth (Plodia interpunctella). CO at concentrations of 0%, 0.8%, or 1.7% (w/w ink mixture) was microencapsulated with polyvinyl alcohol. The microencapsulated CO emulsion was mixed with ink (47% or 59%, w/w) and thinner (20% or 25%, w/w) and coated on polypropylene (PP) films. The PP film was then laminated with a low-density polyethylene (LDPE) film on the coated side. The film with microencapsulated CO at 1.7% repelled P. interpunctella most effectively. Microencapsulation did not negatively affect insect repelling activity. The release rate of cinnamaldehyde, an active repellent, was lower when CO was microencapsulated than that in the absence of microencapsulation. Thermogravimetric analysis exhibited that microencapsulation prevented the volatilization of CO. The tensile strength, percentage elongation at break, elastic modulus, and water vapor permeability of the films indicated that microencapsulation did not affect the tensile and moisture barrier properties (P > 0.05). The results of this study suggest that effective films for the prevention of Indian meal moth invasion can be produced by the microencapsulation of CO using a large-scale film production system. Low-density polyethylene-laminated polypropylene films printed with ink incorporating microencapsulated cinnamon oil using a large-scale film production system effectively repelled Indian meal moth larvae. Without altering the tensile and moisture barrier properties of the film, microencapsulation resulted in the release of an active repellent for extended periods with a high thermal stability of cinnamon oil, enabling commercial film production at high temperatures. This anti-insect film system may have applications to other food-packaging films that use the same ink-printing platform. © 2018 Institute of Food Technologists®.

Enhanced catalytic activity of the nanostructured Co-W-B film catalysts for hydrogen evolution from the hydrolysis of ammonia borane.

Science.gov (United States)

Li, Chao; Wang, Dan; Wang, Yan; Li, Guode; Hu, Guijuan; Wu, Shiwei; Cao, Zhongqiu; Zhang, Ke

2018-08-15

In this work, nanostructured Co-W-B films are successfully synthesized on the foam sponge by electroless plating method and employed as the catalysts with enhanced catalytic activity towards hydrogen evolution from the hydrolysis of ammonia borane (NH 3 BH 3 , AB) at room temperature. The particle size of the as-prepared Co-W-B film catalysts is varied by adjusting the depositional pH value to identify the most suitable particle size for hydrogen evolution of AB hydrolysis. The Co-W-B film catalyst with the particle size of about 67.3 nm shows the highest catalytic activity and can reach a hydrogen generation rate of 3327.7 mL min -1 g cat -1 at 298 K. The activation energy of the hydrolysis reaction of AB is determined to be 32.2 kJ mol -1 . Remarkably, the as-obtained Co-W-B film is also a reusable catalyst preserving 78.4% of their initial catalytic activity even after 5 cycles in hydrolysis of AB at room temperature. Thus, the enhanced catalytic activity illustrates that the Co-W-B film is a promising catalyst for AB hydrolytic dehydrogenation in fuel cells and the related fields. Copyright © 2018 Elsevier Inc. All rights reserved.

Temperature dependence of the Faraday rotation for CdMnCoTe films

International Nuclear Information System (INIS)

Ahn, J. Y.; Tanaka, M.; Imamura, M.

2001-01-01

The temperature dependence of magneto-optical property in the visible wavelength region has been studied on four-element semimagnetic semiconductor CdMnCoTe films deposited on quartz glass substrates by using MBE equipment. A large dispersion of Faraday rotation was observed, and the peak of the Faraday rotation was shifted to the higher photon energies with increasing Mn concentration at low temperatures. At 180 K, the value of the Faraday rotation observed for the Cd 0.647 Mn 0.34 Co 0.013 Te film on quartz glass was -0.36 deg/cmG at 630 nm. It is equivalent to the value of -0.36 deg/cmG observed at 77 K for the Cd 0.52 Mn 0.48 Te film on quartz glass. At 77 K, the Faraday rotation observed for the Cd 0.647 Mn 0.34 Co 0.013 Te film on quartz glass was -0.49 deg/cmG at 610 nm. The value is approximately two times larger than that of the Cd 0.52 Mn 0.48 Te film deposited on the same quartz glass substrate. The origin of the enhancement of Faraday rotation in CdMnCoTe films has been discussed in terms of the magnetic susceptibility χ. [copyright] 2001 American Institute of Physics

Laser heating and oxygen partial pressure effects on the dynamic magnetic properties of perpendicular CoFeAlO films

Energy Technology Data Exchange (ETDEWEB)

Wu, Di [Key Laboratory of Micro and Nano Photonic Structures (Ministry of Education), Department of Optical Science and Engineering, Fudan University, Shanghai 200433 (China); Li, Wei [State Key Laboratory of Precision Spectroscopy and Department of Physics, East China Normal University, Shanghai 200062 (China); Tang, Minghong [Key Laboratory of Micro and Nano Photonic Structures (Ministry of Education), Department of Optical Science and Engineering, Fudan University, Shanghai 200433 (China); Zhang, Zongzhi, E-mail: zzzhang@fudan.edu.cn [Key Laboratory of Micro and Nano Photonic Structures (Ministry of Education), Department of Optical Science and Engineering, Fudan University, Shanghai 200433 (China); Lou, Shitao [State Key Laboratory of Precision Spectroscopy and Department of Physics, East China Normal University, Shanghai 200062 (China); Jin, Q.Y. [Key Laboratory of Micro and Nano Photonic Structures (Ministry of Education), Department of Optical Science and Engineering, Fudan University, Shanghai 200433 (China); State Key Laboratory of Precision Spectroscopy and Department of Physics, East China Normal University, Shanghai 200062 (China)

2016-07-01

The impact of oxidation and laser heating on the dynamic magnetic properties of perpendicularly magnetized Co{sub 50}Fe{sub 25}Al{sub 25}O films has been studied by time-resolved magneto-optical Kerr effect in a fs-laser pump-probe setup. We find that pump laser fluence F{sub p} can affect the effective magnetic anisotropy field and thus the precession frequency f seriously, leading to an increased dependence of effective magnetic damping factor α{sub eff} on the external field at higher fluences. Moreover, the α{sub eff} increases with increasing the oxygen partial pressure P{sub O2} while the uniaxial anisotropy energy K{sub u} and Landau factor g decrease, owing to the increased proportion of superparamagnetic CoFe oxides formed by over-oxidation. By optimizing both the F{sub p} and P{sub O2}, the intrinsic damping factor is determined to be lower than 0.028 for the perpendicular film showing a uniaxial anisotropy energy as high as 4.3×10{sup 6} erg/cm{sup 3}. The results in this study provide a promising approach to manipulate the magnetic parameters for possible applications in spintronic devices. - Highlights: • A new kind of perpendicular thin film material, oxidized CoFeAl, has been fabricated. • The precession frequency and effective damping are strongly affected by higher fluence. • The effective damping factor increases with oxygen partial pressure. • The intrinsic damping factor is below 0.028 for the CFAO film with K{sub u}=4.3×10{sup 6} erg/cm{sup 3}.

Electrochemical fabrication of nanoporous polypyrrole thin films

Energy Technology Data Exchange (ETDEWEB)

Li Mei [Key Laboratory of Organic Optoelectronics and Molecular Engineering (Ministry of Education), Department of Chemistry, Tsinghua University, Beijing, 100084 (China); Yuan Jinying [Key Laboratory of Organic Optoelectronics and Molecular Engineering (Ministry of Education), Department of Chemistry, Tsinghua University, Beijing, 100084 (China)], E-mail: yuanjy@mail.tsinghua.edu.cn; Shi Gaoquan [Key Laboratory of Organic Optoelectronics and Molecular Engineering (Ministry of Education), Department of Chemistry, Tsinghua University, Beijing, 100084 (China)], E-mail: gshi@mail.tsinghua.edu.cn

2008-04-30

Polypyrrole thin films with pores in nanometer scale were synthesized by direct electrochemical oxidation of pyrrole in a mixed electrolyte of isopropyl alcohol, boron trifluoride diethyl etherate, sodium dodecylsulfonate and poly(ethylene glycol) using well-aligned ZnO nanowires arrays as templates. The thin films exhibit high conductivity of ca. {sigma}{sub rt} {approx} 20.5 s/cm and can be driven to bend during redox processes in 1.0 M lithium perchlorate aqueous solution. The movement rate of an actuator based on this nanoporous film was measured to be over 90{sup o}/s at a driving potential of 0.8 V (vs. Ag/AgCl)

Electrochemical fabrication of nanoporous polypyrrole thin films

International Nuclear Information System (INIS)

Li Mei; Yuan Jinying; Shi Gaoquan

2008-01-01

Polypyrrole thin films with pores in nanometer scale were synthesized by direct electrochemical oxidation of pyrrole in a mixed electrolyte of isopropyl alcohol, boron trifluoride diethyl etherate, sodium dodecylsulfonate and poly(ethylene glycol) using well-aligned ZnO nanowires arrays as templates. The thin films exhibit high conductivity of ca. σ rt ∼ 20.5 s/cm and can be driven to bend during redox processes in 1.0 M lithium perchlorate aqueous solution. The movement rate of an actuator based on this nanoporous film was measured to be over 90 o /s at a driving potential of 0.8 V (vs. Ag/AgCl)

Preparation and thermoelectric properties of RF co-sputtered CoSb{sub 3} skutteruddite thin films

Energy Technology Data Exchange (ETDEWEB)

Ahmed, Aziz [University of Science and Technology, Daejeon (Korea, Republic of); Han, Seungwoo [Korea Institute of Machinery and Materials, Daejeon (Korea, Republic of); University of Science and Technology, Daejeon (Korea, Republic of)

2014-11-15

Various skutterudites have been under investigation because of their potential application in thermoelectric materials and devices. These studies indicate that bulk materials with a skutterudite type structure show reasonable thermoelectric behaviors at elevated temperatures, which make them suitable for high-temperature thermoelectric applications. The results of thermoelectric-property measurements on skutterudite-phase CoSb{sub 3} thin films are presented in this study in order to extend the bulk material concept to micro-device applications by using thin film deposition technology. Thin films are deposited on oxidized silicon substrates by using the RF co-sputtering method. The film's composition is found to depend strongly on the deposition conditions. The temperature at which the deposited films transition from an amorphous state to a crystalline state has been reported to be about 153 .deg. C. Therefore, some experiments are performed with the substrate temperature kept at 200 .deg. C to obtain polycrystalline films. The crystal structure of the film is evaluated by using x-ray diffraction (XRD) measurements. Energy dispersive spectroscopy (EDS) is used to determine the film's composition whereas the surface morphology and the thickness are investigated and measured by using scanning electron microscopy (SEM). Finally, the thermoelectric properties, namely, the electrical resistivity and the Seebeck coefficient, are used to calculate the power factor of the deposited thin films and, their variations with temperature are measured. We report a maximum power factor of 0.41 mW/mK{sup 2} for the film deposited at a 200 .deg. C substrate temperature.

Co-sputtered ZnO:Si thin films as transparent conductive oxides

Energy Technology Data Exchange (ETDEWEB)

Faure, C. [CNRS, Univ. Bordeaux, ICMCB, UPR 9048, F33600 Pessac (France); Clatot, J. [LRCS, 33 Rue St Leu, F-80039 Amiens (France); Teule-Gay, L.; Campet, G. [CNRS, Univ. Bordeaux, ICMCB, UPR 9048, F33600 Pessac (France); Labrugere, C. [CeCaMA, Universite de Bordeaux, ICMCB, 87 avenue du Dr. A. Schweitzer, Pessac, F-33608 (France); Nistor, M. [National Institute for Lasers, Plasmas and Radiation Physics, L22, PO Box MG-36, 77125 Bucharest-Magurele (Romania); Rougier, A., E-mail: rougier@icmcb-bordeaux.cnrs.fr [CNRS, Univ. Bordeaux, ICMCB, UPR 9048, F33600 Pessac (France)

2012-12-01

Silicon doped Zinc Oxide thin films, so-called SZO, were deposited at room temperature on glass and plastic substrates by co-sputtering of ZnO and SiO{sub 2} targets. The influence of the SiO{sub 2} target power supply (from 30 to 75 W) on the SZO thin film composition and crystallinity is discussed. Si/Zn atomic ratio, determined by X-ray microprobe, increases from 1.2 to 8.2 at.%. For Si/Zn ratio equal and lower than 3.9%, SZO (S{sub 3.9}ZO) thin films exhibit the Wurzite structure with the (0 0 2) preferred orientation. Larger Si content leads to a decrease in crystallinity. With Si addition, the resistivity decreases down to 3.5 Multiplication-Sign 10{sup -3} Ohm-Sign {center_dot}cm for SZO thin film containing 3.9 at.% of Si prior to an increase. The mean transmittance of S{sub 3.9}ZO thin film on glass substrate approaches 80% (it is about 90% for the film itself) in the visible range (from 400 to 750 nm). Co-sputtered SZO thin films are suitable candidates for large area transparent conductive oxides. - Highlights: Black-Right-Pointing-Pointer Si doped ZnO thin films by co-sputtering of ZnO and SiO{sub 2} targets. Black-Right-Pointing-Pointer Minimum of resistivity for Si doped ZnO thin films containing 3.9% of Si. Black-Right-Pointing-Pointer Si and O environments by X-ray Photoelectron Spectroscopy.

A chiral microwave absorbing absorbent of Fe–CoNiP coated on spirulina

Energy Technology Data Exchange (ETDEWEB)

Xu, Yonggang, E-mail: xuyonggang221@163.com [Science and Technology on Electromagnetic Scattering Laboratory, Shanghai, 200438 (China); Yuan, Liming [Science and Technology on Electromagnetic Scattering Laboratory, Shanghai, 200438 (China); Zhang, Deyuan [School of Mechanical Engineering and Automation, Beihang University, Beijing, 100191 (China)

2015-11-15

A chiral bio-absorbent of Fe–CoNiP coated on the spirulina was fabricated by the electroless and chemical vapor decomposition. The scanning electron microscopy (SEM) was used to evaluate the spirulina cells particle morphology. X-ray diffraction (XRD) patterns were done to analyze the particle crystal grain structure. The permittivity and permeability was measured by a vector network analyzer in frequency 8–18 GHz, and the reflection loss (RL) was calculated. The results showed the carbonyl iron particles (CIPs) and CoNiP were bonded to the spirulina surface, the permittivity and permeability could be enlarged as Fe films coated on the particles compared with the CoNiP spirulina, it was attributed to the excellent electromagnetic property of CIPs. The chiral Fe–CoNiP composites had a better absorbing property at 8–18 GHz than the CoNiP spirulina composite, the RL was −16.26 dB at 10.48 GHz, the absorbing band was 9.5–11.5 GHz of RL less than −10 dB, which indicated the Fe–CoNiP spirulina could be an effective absorbent used in 8–18 GHz. - Highlights: • Absorbers filled with Fe–CoNiP coating on the spirulina were fabricated. • The permittivity and permeability increased as CIPs coated. • The Fe material enhanced the electromagnetic property. • The spirulina coated Fe–CoNiP was effective in 8–18 GHz.

Antitumor Activity of a 5-Hydroxy-1H-Pyrrol-2-(5H-One-Based Synthetic Small Molecule In Vitro and In Vivo.

Directory of Open Access Journals (Sweden)

Yunyun Geng

Full Text Available Alternative chemo-reagents are in great demand because chemotherapy resistance is one of the major challenges in current cancer treatment. 5-hydoxy-1H-pyrrol-2-(5H-one is an important N-heterocyclic scaffold that is present in natural products and medicinal chemistry. However, its antitumor activity has not been systematically explored. In this study, we screened a panel of 5-hydoxy-1H-pyrrol-2-(5H-one derivatives and identified compound 1d as possessing strong anti-proliferative activity in multiple cancer cell lines. Cell cycle analysis revealed that 1d can induce S-phase cell cycle arrest and that HCT116 was sensitive to 1d-induced apoptosis. Further analysis indicated that 1d preferentially induced DNA damage and p53 activation in HCT116 cells and that 1d-induced apoptosis is partly dependent on p53. Furthermore, we showed that 1d significantly suppressed tumor growth in xenograft tumor models in vivo. Taken together, our results suggest that 5-hydoxy-1H-pyrrol-2-(5H-one derivatives bear potential antitumor activity and that 1d is an effective agent for cancer treatment.

Preferred orientation in Cr- and Co-based thin films and its effects on the read/write performance of the media

Science.gov (United States)

Tsai, Hsiao-chu; Lal, Brij B.; Eltoukhy, Atef

1992-04-01

This work investigates the formation of preferred crystallographic orientation (PO) in Cr underlayer as well as CoCrTa and CoCrPtTa thin films and its effects on the recording performance of longitudinal media. The results show that the thin-film media with comparable coercivity but different crystalline PO as measured by x-ray diffraction exhibit significant difference in high-frequency signal amplitude, pulse width, and signal-to-noise ratio. To illustrate the effect of PO on parametric performance, CoCrTa/Cr and CoCrPtTa/Cr media were sputtered on different substrates and/or using special sputtering processes to achieve comparable coercivity but different PO in the films. A PO of Cr(200), which normally occurs on the NiP/Al substrates under adequate sputtering conditions, is found to be the key to obtaining a PO of Co(11.0) in Co-alloy media. The consequence of preferred in-plane c-axis orientation is a higher coercivity and better parametric performance of the medium. The formation of PO in the Cr underlayer is found to be related to the substrate material and the oxygen content in the sputtered films. The nonmetallic canasite substrates tend to promote PO of more stable Cr(110) rather than Cr(200). Consequently, this leads to a PO of out-of-plane c axis on the following Co films. The PO of magnetic layer appears to be an important factor in determining the parametric performance of the media.

Improved high-frequency soft magnetic properties of FeCo films on organic ferroelectric PVDF substrate

Energy Technology Data Exchange (ETDEWEB)

Li, Dong; Wang, Zhen; Han, Xuemeng; Li, Yue; Guo, Xiaobin; Zuo, Yalu; Xi, Li, E-mail: xili@lzu.edu.cn

2015-02-01

FeCo films with various thicknesses were fabricated by direct-current magnetron sputtering on corning glass and organic ferroelectric PVDF substrates at the same time with 5 nm Ru seed layer and 5 nm Ta protective layer. The in-plane uniaxial anisotropy field of FeCo on glass substrate increases from 24 to 36 Oe with the increase of FeCo film thickness from 5 to 100 nm. However, a large in-plane anisotropy field of FeCo on PVDF substrate increases with FeCo thickness from 5 to 20 nm and gradually decreases with the FeCo thickness further increasing. Atomic force microscope images of FeCo on glass show quite smooth surface with root-mean-square roughness around 0.5 nm and have none visible granules on the surface for all samples. While, AFM images of FeCo on PVDF show quite rough surface with RMS roughness around 25 nm and have visible granules with the smallest granules appearing at the FeCo thickness of 20 nm. The permeability spectra show the typical ferromagnetic resonance phenomenon and can be well fitted by the LLG equation with the obtained experimental parameters. The ferromagnetic resonance frequency can reach 7.0 GHz for the 20 nm FeCo film on PVDF. Moreover, the quality factor of this sample can respectively reach 26, 12 and 7 at 1.0, 2.0, and 3.0 GHz, indicating the potential real 3G application for high-frequency devices. - Highlights: 1.Magnetic and morphological properties of FeCo films on PVDF substrates are studied. 2.The large anisotropy field of FeCo films on PVDF is obtained. 3.Improved high frequency properties of FeCo films on flexible substrates are obtained. 4.The origin of improved high frequency properties of FeCo films on PVDF is studied.

High coercivity Sm-Co thin films from elemental Sm/Co multilayer deposition and their microstructural aspects

Energy Technology Data Exchange (ETDEWEB)

Krishnan, M. [Surface Engineering Division, CSIR-National Aerospace Laboratories, Bangalore 560 017 (India); Department of Physics, National Institute of Technology Calicut, Calicut 673601 (India); Predeep, P. [Department of Physics, National Institute of Technology Calicut, Calicut 673601 (India); Sridhara Rao, D.V. [Defence Metallurgical Research Laboratories, Hyderabad 500058 (India); Prajapat, C.L.; Singh, M.R. [Technical Physics Division, Bhabha Atomic Research Centre, Mumbai 400085 (India); Barshilia, Harish C. [Surface Engineering Division, CSIR-National Aerospace Laboratories, Bangalore 560 017 (India); Chowdhury, P., E-mail: pchowdhury@nal.res.in [Surface Engineering Division, CSIR-National Aerospace Laboratories, Bangalore 560 017 (India)

2017-05-15

Hard magnetic thin films with high coercivity were fabricated by magnetron sputtering on MgO(100) and quartz substrates. The films were grown by depositing sequentially Sm and Co layers at an elevated substrate temperature of 500 °C. Subsequent post-annealing was carried out at various temperatures in range of 500–700 °C to form Sm-Co hard magnetic thin films. X-ray diffraction studies revealed the formation of randomly oriented SmCo{sub 5} crystallites on quartz substrate, whereas, a textured growth of Sm{sub 2}Co{sub 7} with strong (110) crystalline phases was observed on MgO substrate. Microstructural analyses were carried out using Transmission Electron Microscopy (TEM) for samples grown on MgO substrate at 650 °C and inferred the presence of high density planar defects along with large grain boundaries. Further microdiffraction studies confirmed the presence of SmCo{sub 3} as an impurity phase in the films. Magnetic hysteresis measurements indicate the square hysteresis behaviors with high coercivity value of 3.1 T and 2.7 T for 650 °C annealed samples on both MgO and quartz substrates, respectively. The origin of such high coercivity value was then correlated with pinning type of spin reversal mechanism as confirmed through the analyses of demagnetization curves. The magnetic force microscopy images for films on MgO substrate, annealed at 650 °C, revealed the presence of magnetic domains with size higher than 1 µm. The formed magnetic domains lacked well defined boundaries indicating an enhanced exchange coupling between the grain clusters. - Highlights: • Ewald technique in micromagnetic simulations with periodic boundary conditions. • Effect of micromagnetic parameters on hysteresis in exchange spring magnets. • Importance of the interface exchange coupling for hard-soft nanocomposites. • Geometry dependence of the optimal soft phase size in exchange spring magnets.

Microstructure and magnetic properties of FeCo epitaxial thin films grown on MgO single-crystal substrates

International Nuclear Information System (INIS)

Shikada, Kouhei; Ohtake, Mitsuru; Futamoto, Masaaki; Kirino, Fumiyoshi

2009-01-01

FeCo epitaxial films were prepared on MgO(100), MgO(110), and MgO(111) substrates by ultrahigh vacuum molecular beam epitaxy. FeCo thin films with (100), (211), and (110) planes parallel to the substrate surface grow on respective MgO substrates. FeCo/MgO interface structures are studied by high-resolution cross-sectional transmission electron microscopy and the epitaxial growth mechanism is discussed. Atomically sharp boundaries are recognized between the FeCo thin films and the MgO substrates where misfit dislocations are introduced in the FeCo thin films presumably to decrease the lattice misfits. Misfit dislocations are observed approximately every 9 and 1.4 nm in FeCo thin film at the FeCo/MgO(100) and the FeCo/MgO(110) interfaces, respectively. X-ray diffraction analysis indicates that the lattice spacing measured parallel to the single-crystal substrate surfaces are in agreement within 0.1% with those of the respective bulk values of Fe 50 Co 50 alloy crystal, showing that the FeCo film strain is very small. The magnetic anisotropies of these epitaxial films basically reflect the magnetocrystalline anisotropy of bulk FeCo alloy crystal

Vortex pinning in artificially layered Ba(Fe,Co)2As2 film

Science.gov (United States)

Oh, M. J.; Lee, Jongmin; Seo, Sehun; Yoon, Sejun; Seo, M. S.; Park, S. Y.; Kim, Ho-Sup; Ha, Dong-Woo; Lee, Sanghan; Jo, Youn Jung

2018-06-01

Static high critical current densities (Jc) > 1 MA/cm2 with magnetic field parallel or perpendicular to c-axis were realized in Co-doped/undoped multilayerd BaFe2As2 films. We made a current bridge by FIB to allow precise measurements, and confirmed that the boundary quality using FIB was considerably better than the quality achieved using a laser. The presence of a high in-plane Jc suggested the existence of c-axis correlated vortex pinning centers. To clarify the relationship between the Jc performance and superstructures, we investigated the magnetic flux pinning mechanism using scaling theory of the volume pinning force Fp(H). The Jc(H) curves, Fp/Fp,max vs. h = H/Hirr curves, and parameters p and q depended on the characteristics of the flux pinning mechanism. It was found that the dominant pinning mechanism of Co-doped/undoped multilayerd BaFe2As2 films was Δl-pinning and the inserted undoped BaFe2As2 layers remained non-superconducting. The dominant pin geometry varied when the magnetic field direction changed. It was concluded that the artificially layered BaFe2As2 film is a 3-D superconductor due to its long correlation length compared to the thickness of the non-superconducting layer.

Optical and magneto-optical characterization of TbFeCo thin films in trilayer structures

International Nuclear Information System (INIS)

McGahan, W.A.; He, P.; Chen, L.; Bonafede, S.; Woollam, J.A.; Sequeda, F.; McDaniel, T.; Do, H.

1991-01-01

A series of TbFeCo films ranging in thickness from 100 to 800 A have been deposited in trilayer structures on silicon wafer substrates, with Si 3 N 4 being employed as the dielectric material. These films have been characterized both optically and magneto-optically by variable angle of incidence spectroscopic ellipsometry, normal angle of incidence reflectometry, and normal angle of incidence Kerr spectroscopy. From these measurements, the optical constants n and k have been determined for the TbFeCo films, as well as the magneto-optical constants Q1 and Q2. Results are presented that demonstrate the lack of dependence of these constants on the thickness of the TbFeCo film, and which can be used for calculating the expected optical and magneto-optical response of any multilayer structure containing similar TbFeCo films

Structural, electrical and magnetic studies of Co:SnO{sub 2} and (Co,Mo):SnO{sub 2} films prepared by pulsed laser deposition

Energy Technology Data Exchange (ETDEWEB)

Dalui, S., E-mail: ssdalui@fc.ul.pt [University of Lisbon, Physics Dept. and ICEMS, 1749-016 Lisboa (Portugal); Instituto Superior de Engenharia de Lisboa and ICEMS, 1959-007 Lisboa (Portugal); Rout, S. [University of Lisbon, Physics Dept. and ICEMS, 1749-016 Lisboa (Portugal); Silvestre, A.J. [Instituto Superior de Engenharia de Lisboa and ICEMS, 1959-007 Lisboa (Portugal); Lavareda, G. [New University of Lisbon, Mater. Sci. Dept. and CTS, 2829-516 Caparica (Portugal); Pereira, L.C.J. [Instituto Superior Técnico, ITN and CFMCUL, 2686-953 Sacavém (Portugal); Brogueira, P. [Instituto Superior Técnico, Physics Dept. and ICEMS, 1049-001 Lisboa (Portugal); Conde, O. [University of Lisbon, Physics Dept. and ICEMS, 1749-016 Lisboa (Portugal)

2013-08-01

Here we report on the structural, optical, electrical and magnetic properties of Co-doped and (Co,Mo)-codoped SnO{sub 2} thin films deposited on r-cut sapphire substrates by pulsed laser deposition. Substrate temperature during deposition was kept at 500 °C. X-ray diffraction analysis showed that the undoped and doped films are crystalline with predominant orientation along the [1 0 1] direction regardless of the doping concentration and doping element. Optical studies revealed that the presence of Mo reverts the blue shift trend observed for the Co-doped films. For the Co and Mo doping concentrations studied, the incorporation of Mo did not contribute to increase the conductivity of the films or to enhance the ferromagnetic order of the Co-doped films.

Electrodeposition and Capacitive Behavior of Films for Electrodes of Electrochemical Supercapacitors

OpenAIRE

Shi C; Zhitomirsky I

2010-01-01

Abstract Polypyrrole films were deposited by anodic electropolymerization on stainless steel substrates from aqueous pyrrole solutions containing sodium salicylate and tiron additives. The deposition yield was studied under galvanostatic conditions. The amount of the deposited material was varied by the variation of deposition time at a constant current density. SEM studies showed the formation of porous films with thicknesses in the range of 0–3 μm. Cyclic voltammetry data for the...

Soft Magnetic Properties of High-Entropy Fe-Co-Ni-Cr-Al-Si Thin Films

Directory of Open Access Journals (Sweden)

Pei-Chung Lin

2016-08-01

Full Text Available Soft magnetic properties of Fe-Co-Ni-Al-Cr-Si thin films were studied. As-deposited Fe-Co-Ni-Al-Cr-Si nano-grained thin films showing no magnetic anisotropy were subjected to field-annealing at different temperatures to induce magnetic anisotropy. Optimized magnetic and electrical properties of Fe-Co-Ni-Al-Cr-Si films annealed at 200 °C are saturation magnetization 9.13 × 105 A/m, coercivity 79.6 A/m, out-of-plane uniaxial anisotropy field 1.59 × 103 A/m, and electrical resistivity 3.75 μΩ·m. Based on these excellent properties, we employed such films to fabricate magnetic thin film inductor. The performance of the high entropy alloy thin film inductors is superior to that of air core inductor.

Giant coercivity in ferromagnetic Co doped ZnO single crystal thin film

International Nuclear Information System (INIS)

Loukya, B.; Negi, D.S.; Dileep, K.; Kumar, N.; Ghatak, Jay; Datta, R.

2013-01-01

The origin of ferromagnetism in ZnO doped with transition metal impurities has been discussed extensively and appeared to be a highly controversial and challenging topic in today's solid state physics. Magnetism observed in this system is generally weak and soft. We have grown Co:ZnO up to 30 at% Co in single crystal thin film form on c-plane sapphire. A composition dependent coercivity is observed in this system which reaches peak value at 25 at% Co, the values are 860 Oe and 1149 Oe with applied field along parallel and perpendicular to the film substrate interface respectively. This giant coercivity might pave the way to exploit this material as a magnetic semiconductor with novel logic functionalities. The findings are explained based on defect band itinerant ferromagnetism and its partial interaction with localized d electrons of Co through charge transfer. Besides large coercivity, an increase in the band gap with Co concentration has also been observed along with blue emission peak with long tail confirming the formation of extended point defect levels in the host lattice band gap. - Highlights: • Co doped ZnO ferromagnetic single crystal thin film. • Giant coercivity in Co:ZnO thin film which may help to turn this material into application. • Cathodoluminescence (CL) data showing increase in band gap with Co concentrations. • A theoretical proposal is made to explain the observed giant coercivity

CVD of alternated microcrystalline (MCD) and nanocrystalline (NCD) diamond films on WC-TIC-CO substrates

International Nuclear Information System (INIS)

Campos, Raonei Alves; Contin, Andre; Trava-Airoldi, Vladimir J.; Corat, Evaldo Jose; Barquete, Danilo Maciel

2010-01-01

CVD Diamond coating of WC-TiC-Co cutting tools has been an alternative to increase tool lifetime. Experiments have shown that residual stresses produced during films growth on WC-TiC-Co substrates significantly increases with increasing film thickness up to 20 μm and usually leads to film delamination. In this work alternated micro- and nanocrystalline CVD diamond films have been used to relax interface stresses and to increase diamond coatings performance. WC-TiC-Co substrates have been submitted to a boronizing thermal diffusion treatment prior to CVD diamond films growth. After reactive heat treatment samples were submitted to chemical etching in acid and alkaline solution. The diamond films deposition was performed using HFCVD reactor with different gas concentrations for microcrystalline (MCD) and nano-crystalline (NCD) films growth. As a result, we present the improvement of diamond films adherence on WC-TiC-Co, evaluated by indentation and machining tests. Samples were characterized by Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray (EDX) for qualitative analysis of diamond films. X-ray Diffraction (XRD) was used for phases identification after boronizing process. Diamond film compressive residual stresses were analyzed by Raman Scattering Spectroscopy (RSS). (author)

Effects of Crystal Morphology on Singlet Exciton Fission in Diketopyrrolopyrrole Thin Films.

Science.gov (United States)

Hartnett, Patrick E; Margulies, Eric A; Mauck, Catherine M; Miller, Stephen A; Wu, Yilei; Wu, Yi-Lin; Marks, Tobin J; Wasielewski, Michael R

2016-02-25

Singlet exciton fission (SF) is a promising strategy for increasing photovoltaic efficiency, but in order for SF to be useful in solar cells, it should take place in a chromophore that is air-stable, highly absorptive, solution processable, and inexpensive. Unlike many SF chromophores, diketopyrrolopyrrole (DPP) conforms to these criteria, and here we investigate SF in DPP for the first time. SF yields in thin films of DPP derivatives, which are widely used in organic electronics and photovoltaics, are shown to depend critically on crystal morphology. Time-resolved spectroscopy of three DPP derivatives with phenyl (3,6-diphenylpyrrolo[3,4-c]pyrrole-1,4(2H,5H)-dione, PhDPP), thienyl (3,6-di(thiophen-2-yl)pyrrolo[3,4-c]pyrrole-1,4(2H,5H)-dione, TDPP), and phenylthienyl (3,6-di(5-phenylthiophen-2-yl)pyrrolo[3,4-c]pyrrole-1,4(2H,5H)-dione, PhTDPP) aromatic substituents in 100-200 nm thin films reveals that efficient SF occurs only in TDPP and PhTDPP (τSF = 220 ± 20 ps), despite the fact that SF is most exoergic in PhDPP. This result correlates well with the greater degree of π-overlap and closer π-stacking in TDPP (3.50 Å) and PhTDPP (3.59 Å) relative to PhDPP (3.90 Å) and demonstrates that SF in DPP is highly sensitive to the electronic coupling between adjacent chromophores. The triplet yield in PhTDPP films is determined to be 210 ± 35% by the singlet depletion method and 165 ± 30% by the energy transfer method, showing that SF is nearly quantitative in these films and that DPP derivatives are a promising class of SF chromophores for enhancing photovoltaic performance.

Influencing the electronic interaction in diferrocenyl-1-phenyl-1H-pyrroles.

Science.gov (United States)

Hildebrandt, Alexander; Lang, Heinrich

2011-11-28

Functionalised diferrocenyl-1-phenyl-1H-pyrroles were synthesised using Negishi C,C cross-coupling reactions. The influence of different substituents at the phenyl moiety on the electronic interaction was studied using electrochemistry (cyclic and square-wave voltammetry) and spectro-electrochemistry (in situ UV/Vis-NIR spectroscopy). The ferrocenyl moieties gave rise to two sequential, reversible redox processes in each of the diferrocenyl-1-phenyl-1H-pyrroles. The observed ΔE(1/2) values (ΔE(1/2) = difference between first and second oxidation) range between 420 and 480 mV. A linear relationship between the Hammett constants σ of the substituents and the separation of the redox potentials exists. The NIR measurements confirm electronic communication between the iron centers as intervalence charge transfer (IVCT) absorptions were observed in the corresponding mixed-valent monocationic species. All compounds were classified as class II systems according to Robin and Day (M. B. Robin and P. Day, Adv. Inorg. Chem., 1967, 10, 247-423). The oscillator strength of the charge transfer transition highly depends on the electron donating or electron withdrawing character of the phenyl substituents. This enables direct tuning of the intermetallic communication by simple modification of the molecule's functional group. Hence, this series of molecules may be regarded as model compounds for single molecule transistors.

Poly(1-(2-carboxyethyl)pyrrole)/polypyrrole composite nanowires for glucose biosensor

International Nuclear Information System (INIS)

Jiang Hairong; Zhang Aifeng; Sun Yanan; Ru Xiaoning; Ge Dongtao; Shi Wei

2012-01-01

A novel glucose biosensor based on poly(1-(2-carboxyethyl)pyrrole) (PPyCOOH)/polypyrrole (PPy) composite nanowires was developed by immobilizing glucose oxidase (GOD) on the nanowires via covalent linkages. The PPyCOOH/PPy composite nanowires were fabricated by a facile two-step electrochemical synthesis route. First, PPy nanowires were synthesized in phosphate buffer solution using organic sulfonic acid, p-toluenesulfonate acid, as soft-template. Then, PPyCOOH/PPy composite nanowires were obtained by polymerizing 1-(2-carboxyethyl)pyrrole onto PPy nanowires via electrochemical method. Scanning electron microscopic, FT-IR spectra, X-ray photoelectron spectroscopy and cyclic voltammograms were used to characterize the structural and electrical behaviors of the composite nanowires. The PPyCOOH/PPy composite nanowires exhibited uniform diameter, high reactive site (-COOH), large specific surface, excellent electroactivity and good adhesion to electrode. The glucose biosensor was constructed by covalently coupling GOD to the composite nanowires. The biosensor response was rapid (5 s), highly sensitive (33.6 μA mM −1 cm −2 ) with a wide linear range (up to 10.0 mM) and low detection limit (0.63 μM); it also exhibited high stability and specificity to glucose. The attractive electrochemical and structural properties of PPyCOOH/PPy composite nanowires suggested potential application for electrocatalysis and biosensor.

Atomic structures of Ruddlesden-Popper faults in LaCoO3/SrRuO3 multilayer thin films induced by epitaxial strain

Science.gov (United States)

Wang, Wei; Zhang, Hui; Shen, Xi; Guan, Xiangxiang; Yao, Yuan; Wang, Yanguo; Sun, Jirong; Yu, Richeng

2018-05-01

In this paper, scanning transmission electron microscopy is used to study the microstructures of the defects in LaCoO3/SrRuO3 multilayer films grown on the SrTiO3 substrates, and these films have different thickness of SrRuO3 (SRO) layers. Several types of Ruddlesden-Popper (R.P.) faults at an atomic level are found, and these chemical composition fluctuations in the growth process are induced by strain fields originating from the film-film and film-substrate lattice mismatches. Furthermore, we propose four types of structural models based on the atomic arrangements of the R.P. planar faults, which severely affect the functional properties of the films.

Knorr-Rabe partial reduction of pyrroles: Application to the synthesis of indolizidine alkaloids

Directory of Open Access Journals (Sweden)

Ryan John H

2008-01-01

Full Text Available Abstract Background The Birch reduction of electron rich pyrroles does not occur readily. However, dissolving metal reduction with zinc under acidic conditions gives 3-pyrrolines (2,5-dihydropyrroles in reasonable yield. This dissolving metal reduction was first reported by Knorr and Rabe in 1901 but since then has only been reported for the reduction of electron rich pyrroles. Results The partial reduction of bicyclic α-ketopyrrole derivatives has been performed under dissolving metal conditions with zinc and hydrochloric acid to give excellent yields of hexahydroindolizidines. This reduction method has been utilised for the diastereoselective synthesis of 5-alkylindolizidines and the stereoselectivity obtained is opposite to that of catalytic hydrogenation. Conclusion An efficient stereoselective synthesis of indolizidine alkaloids has been developed from α-ketopyrrole intermediates using a modified version of Knorr and Rabe's pyrrole reduction.

Blood Pyrrole-Protein Adducts--A Biomarker of Pyrrolizidine Alkaloid-Induced Liver Injury in Humans.

Science.gov (United States)

Ruan, Jianqing; Gao, Hong; Li, Na; Xue, Junyi; Chen, Jie; Ke, Changqiang; Ye, Yang; Fu, Peter Pi-Cheng; Zheng, Jiang; Wang, Jiyao; Lin, Ge

2015-01-01

Pyrrolizidine alkaloids (PAs) induce liver injury (PA-ILI) and is very likely to contribute significantly to drug-induced liver injury (DILI). In this study we used a newly developed ultra-high performance liquid chromatography-triple quadrupole-mass spectrometry (UHPLC-MS)-based method to detect and quantitate blood pyrrole-protein adducts in DILI patients. Among the 46 suspected DILI patients, 15 were identified as PA-ILI by the identification of PA-containing herbs exposed. Blood pyrrole-protein adducts were detected in all PA-ILI patients (100%). These results confirm that PA-ILI is one of the major causes of DILI and that blood pyrrole-protein adducts quantitated by the newly developed UHPLC-MS method can serve as a specific biomarker of PA-ILI.

Effect of Long Selenization Time on Co Films under a Low Temperature of 300 °C to Synthesize a Nanostructure CoSe2 and Optical Properties

Science.gov (United States)

Wu, Po-Feng; Shi, Jen-Bin; Cheng, Bo-Ci; Wu, Cheng-Han; Lee, Hsuan-Wei; Lin, Hsien-Sheng; Cheng, Fu-Chou; Chen, Kuan-Ping

2018-05-01

This work investigates a simple and non-toxic method to transform pre-deposited amorphous Co film into CoSe2 films at a fixed, low temperature of 300 °C. Single CoSe2-phase films having good crystallinity were obtained at a selenisation time ≧ 24 hours. A nanostructure CoSe2 having two different nano-morphological layers was observed. The CoSe2 films (72 hours) observed a large absorption and a direct band gap.

Co thin film with metastable bcc structure formed on GaAs(111 substrate

Directory of Open Access Journals (Sweden)

Minakawa Shigeyuki

2014-07-01

Full Text Available Co thin films are prepared on GaAs(111 substrates at temperatures ranging from room temperature to 600 ºC by radio-frequency magnetron sputtering. The growth behavior and the detailed resulting film structure are investigated by in-situ reflection high-energy electron diffraction and X-ray diffraction. In early stages of film growth at temperatures lower than 200 ºC, Co crystals with metastable A2 (bcc structure are formed, where the crystal structure is stabilized through hetero-epitaxial growth. With increasing the film thickness beyond 2 nm, the metastable structure starts to transform into more stable A1 (fcc structure through atomic displacements parallel to the A2{110} close-packed planes. The crystallographic orientation relationship between the A2 and the transformed A1 crystals is A1{111} || A2{110}. When the substrate temperature is higher than 400 ºC, Ga atoms of substrate diffuse into the Co films and a Co-Ga alloy with bcc-based ordered structure of B2 is formed.

Synthesis and thin film growth of alkaline cobaltates Na{sub x}CoO{sub 2} and Li{sub x}CoO{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Hildebrandt, Sandra

2013-02-18

In this study sol-gel synthesis was used to fabricate Na{sub x}CoO{sub 2}, LiNi{sub 1/2}Co{sub 1/2}O{sub 2} and LiNi{sub 1/3}Mn{sub 1/3}Co{sub 1/3}O{sub 2}. By using acetate precursors a lower process temperature was accessible, which has a positive effect on the sodium and lithium loss during synthesis. The lithium based powders were single phase and kept cation stoichiometry after sintering. A small grain size is favourable for battery applications. Sodium content was slightly reduced after temperature treatment compared to the initial cation mixture, due to the high volatility of Na. To fabricate thin films PLD was used for deposition. All films were deposited on SrTiO{sub 3} substrates. The growth mechanism of Na{sub x}CoO{sub 2} on SrTiO{sub 3} was investigated and an in-plane and out-of-plane relation between film an substrate was found. The films grow 15 and 45 rotated with respect to the ab-plane of the substrate and grow in c-axis direction out-of-plane. The sodium content and the crystallinity of the Na{sub x}CoO{sub 2} was investigated as a function of the post deposition treatment. A change of x between 0.38 and 0.84 can be achieved. The γ-phase was preserved in all films despite of the change of the sodium content. The in-situ variation of sodium stoichiometry, allows to tune the film properties in a wide range. This feature is an advantage compared to bulk Na{sub x}CoO{sub 2}, in which only certain stoichiometries can be stabilized. Fabrication of superconducting thin films Na{sub 0.33}CoO{sub 2}.1.3H{sub 2}O was challenging, since the superconducting phase is metastable and hardly to stabilize as a thin film. LiNi{sub 1/3}Mn{sub 1/3}Co{sub 1/3}O{sub 2} and LiNi{sub 1/2}Co{sub 1/2}O{sub 2} thin films were grown by PLD in (104)-orientation. These thin film materials are promising candidates as cathode materials for the development of thin film batteries.

(0 0 1) textured CoPt-Ag nanocomposite films for high-density perpendicular magnetic recording

International Nuclear Information System (INIS)

Xue, S.X.; Wang, H.; Wang, H.B.; Yang, F.J.; Wang, J.A.; Cao, X.; Gao, Y.; Huang, Z.B.; Li, Z.Y.; Li, Q.; Wong, S.P.

2006-01-01

CoPt/Ag nanocomposite films were prepared by magnetron sputtering. The dependence of texture and magnetic properties on film thickness, Ag atomic fraction and annealing conditions is investigated. Films with a thickness about 20 nm are easy to form with (0 0 1) orientation. The existence of the Ag in the film plays a dominant role in inducing the (0 0 1) texture of the film and suppressing the growth of the CoPt grains during annealing. The Co 35 Pt 38 Ag 27 film after annealing at 600 deg. C exhibits a large perpendicular coercivity of 5.6 kOe and a squareness of 0.90 with a small average grains size of 12.5 nm

Self-association and infrared spectres of some heterocyclic compounds based on pyrrol in solid state

International Nuclear Information System (INIS)

Mulloev, N.; Nurulloev, M.; Narziev, B.N.

1993-01-01

Present article is devoted to self-association and infrared spectres of some heterocyclic compounds based on pyrrol in solid state. The study results of self-association specified by molecular hydrogen bonds of some heterocyclic compounds based on pyrrol on spectres of infrared absorption of stretching vibrations of N-H group were considered.

NMR-ON on 60CoCo(fcc, hcp, thin film), 52MnCo(fcc), and 90NbCo(fcc)

International Nuclear Information System (INIS)

Zech, E.; Hagn, E.; Ernst, H.; Eska, G.

1978-01-01

With the NMR-ON method the magnetic hyperfine splitting constant of dilute impurities in a ferromagnetic host material (Fe, Ni, Co) can be determined with high accuracy (10 -3 ...10 -4 ). Only few NMR-ON experiments with Co as host lattice have been performed up to now. In constrast to Fe and Ni, two stable modifications exist for Co (fcc and hcp). In the hcp case the magnetic hyperfine field is expected to be anisotropic. Due to the electric field gradient, which is present in this case, a (small) guadrupole interaction is superimposed to the magnetic hyperfine interaction. For 60 CoCo measurements were done on a fcc foil, a hcp single crystal, and on thin films, which were prepared by evaporating Co into glass. For 52 MnCo and 90 NbCo measurements were performed for fcc Co. (Auth.)

Photopatterning of heterostructured polymer Langmuir-Blodgett films

International Nuclear Information System (INIS)

Li Tiesheng; Mitsuishi, Masaya; Miyashita, Tokuji

2008-01-01

Heterostructured polymer Langmuir-Blodgett (LB) film prepared by using poly(N-dodecylacrylamide-co-t-butyl 4-vinylphenyl carbonate) (p(DDA-tBVPC53)) and poly(N-neopentyl methacrylamide-co-9-anthrylmethyl methacrylate) (p(nPMA-AMMA10)) polymer LB films which can act as photogenerator layers were investigated. Patterns with a resolution of 0.75 μm were obtained on heterostructured polymer LB films composed of 4 layers of p(nPMA-AMMA10) LB film (top layers) and 40 layers of p(DDA-tBVPC53) LB film (under layers) on a silicon wafer by deep UV irradiation followed by development with 1% tetramethylammonium hydroxide aqueous solution. The sensitivity of the heterostructured polymer LB films was improved without loss of the resolution compared with p(DDA-tBVPC53) LB film. The etch resistance of the heterostructured polymer LB films was sufficiently good to allow patterning of a copper film suitable for photomask fabrication

Effect of thermal treatments and Co concentration on the structural and luminescent properties of sputtered TiO{sub 2}:Co films

Energy Technology Data Exchange (ETDEWEB)

Carmona-Rodriguez, J. [Instituto Tecnologico Superior de Poza Rica, Luis Donaldo Colosio, S/N Col. Arroyo del Maiz, 93230 Poza Rica, Veracruz (Mexico); Rodriguez-Melgarejo, F.; Hernandez-Landaverde, M.A.; Urbina-Alvarez, J.E.; Marquez-Marin, J.; Zuniga-Romero, C.; Jimenez-Sandoval, S. [Centro de Investigacion y de Estudios Avanzados del IPN, Unidad Queretaro, A.P. 1-798, 76001 Queretaro, Qro. (Mexico); Vargas, S.; Estevez, M. [Centro de Fisica Aplicada y Tecnologia Avanzada, UNAM, Campus Juriquilla, 76230 Queretaro, Qro. (Mexico); Rodriguez, R. [Centro de Fisica Aplicada y Tecnologia Avanzada, UNAM, Campus Juriquilla, 76230 Queretaro, Qro. (Mexico); Division de Ciencias de la Salud, UVM, Campus Queretaro, Juriquilla, Queretaro, Qro. (Mexico)

2012-11-15

Thin films of Co-doped titania were grown at room temperature by rf reactive co-sputtering. A post-growth annealing procedure was carried out at 300, 450, and 750 C in an inert argon atmosphere. The samples were studied using X-ray diffraction, micro Raman, UV-Vis, and photoluminescence (PL) spectroscopies. The properties of the films were analyzed as a function of the Co concentration and the annealing temperature. The as-grown films were amorphous; however, after a thermal annealing procedure the samples presented a Co-concentration-dependent transition to the anatase phase. In particular, the samples annealed at 300 C showed a strong and broad PL signal that was quenched after exposure to an Ar{sup +} laser beam ({lambda} = 488.0 nm) focused through a microscope objective. The emission properties of the films have been ascribed to defects arising during the amorphous-anatase structural phase transition. It was also shown that the intensity and quenching rate of the PL depended upon the Co concentration and the annealing temperature. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Novel composite materials synthesized by the high-temperature interaction of pyrrole with layered oxide matrices

Science.gov (United States)

Pavel, Alexandru Cezar

employed very acidic pH levels and long reaction times. The nanoscrolls proved to be an excellent precursor for the synthesis of reduced vanadium oxide nanosheets by the redox intercalation of long chain monoamine molecules. In a related development, the very first synthetic metal---mixed-valence polyoxovanadate salt hybrid material was synthesized in the form of a polypyrrole---tetrammonium hexavanadate microcomposite by a redox simultaneous co-precipitation in an aqueous solution. The novel material displayed good mechanical properties towards solid lubricant applications and tunable electronic conductivity. Nanocomposites of polypyrrole---layered bismuthates were produced by the topotactic intercalation of pyrrole and its subsequent in situ polymerization. Insulating and superconducting layered bismuthates were used in a similar experimental procedure that used pre-intercalated iodine species as sacrificial topotactic oxidizing agents. A novel method of iodine intercalation by a solution-based transport procedure was used in the process. Interaction of pyrrole with layered bismuthates at high reaction temperatures led to the formation of polymer-covered metal nanorods as a result of intrinsic lattice templating effect. The successful synthesis of the 1-D heterogeneous nanostructures represents the first example in which nanocomposites were used as precursors. Appropriate doping of the initial layered ceramic substrates led to polymer-covered metal alloy nanorods.

Orientation-dependent structural and photocatalytic properties of LaCoO3 epitaxial nano-thin films

Science.gov (United States)

Zhang, Yan-ping; Liu, Hai-feng; Hu, Hai-long; Xie, Rui-shi; Ma, Guo-hua; Huo, Ji-chuan; Wang, Hai-bin

2018-02-01

LaCoO3 epitaxial films were grown on (100), (110) and (111) oriented LaAlO3 substrates by the polymer-assisted deposition method. Crystal structure measurement and cross-section observation indicate that all the LaCoO3 films are epitaxially grown in accordance with the orientation of LaAlO3 substrates, with biaxial compressive strain in the ab plane. Owing to the different strain directions of CoO6 octahedron, the mean Co-O bond length increases by different amounts in (100), (110) and (111) oriented films compared with that of bulk LaCoO3, and the (100) oriented LaCoO3 has the largest increase. Photocatalytic degradation of methyl orange indicates that the order of photocatalytic activity of the three oriented films is (100) > (111) > (110). Combined with analysis of electronic nature and band structure for LaCoO3 films, it is found that the change of the photocatalytic activity is closely related to the crystal field splitting energy of Co3+ and Co-O binding energy. The increase in the mean Co-O bond length will decrease the crystal field splitting energy of Co3+ and Co-O binding energy and further reduce the value of band gap energy, thus improving the photocatalytic activity. This may also provide a clue for expanding the visible-light-induced photocatalytic application of LaCoO3.

Enhanced electrochemical performance of CoAl-layered double hydroxide nanosheet arrays coated by platinum films

International Nuclear Information System (INIS)

Cheng, J.P.; Fang, J.H.; Li, M.; Zhang, W.F.; Liu, F.; Zhang, X.B.

2013-01-01

Graphical abstract: Schematic illustration for the electron transport between the current collector and the active CoAl LDH arrays, where the yellow arrows indicate the high resistance of CoAl LDH, while the green arrows present the high conductivity of Pt films on LDH. -- Highlights: •CoAl layered double hydroxide nanosheet arrays are synthesized by hydrothermal method. •Pt films coated on surface of CoAl nanosheets facilitate fast electron transport. •CoAl LDH nanosheets coated with Pt film for 5 min have an excellent performance. -- Abstract: Three-dimensional network of cobalt and aluminum layered double hydroxide (LDH) nanosheets was synthesized on nickel foam by a simple hydrothermal method. The CoAl-LDH nonosheets were subsequently coated by ion sputtering with thin layers of Pt films to facilitate fast electron transport between current collector and the CoAl-LDH active materials. The optimal thickness of the Pt film acquiring the best performance was identified by applying various sputtering time in controlled experiments. The supercapacitor built by the CoAl-LDH nanosheets coated with Pt film sputtered for 5 min has a high specific capacitance (734.4 F g −1 at 3 A g −1 ), excellent rate capability as well as cycling stability. Moreover, it showed a long life of 77% retention after 6000 cycles and its general morphology was preserved after the test. The synergetic affect of conductive layer of Pt films and CoAl-LDH on the improvement of electrochemical properties was discussed and this would provide a useful clue in designing novel and effective electrode materials for supercapacitors

Effect of blueberry agro-industrial waste addition to corn starch-based films for the production of a pH-indicator film.

Science.gov (United States)

Luchese, Cláudia Leites; Sperotto, Natalia; Spada, Jordana Corralo; Tessaro, Isabel Cristina

2017-11-01

Intelligent packaging is an emerging area of food technology that can provide better preservation and be of further convenience for consumers. It is recommended that biodegradable materials be used to develop low-impact designs for better packaging, which could benefit the environment by simply expanding their use to new areas. In this work, corn starch, glycerol and blueberry powder (with and without prior fruit bleaching) were used to produce films by casting. Blueberry powder, a co-product from juice processing, which is rich in anthocyanins, was added in the films to evaluate its potential as a colorimetric indicator, due to the ability of anthocyanin to change color when placed in an acidic or basic environment. After the films were immersed in different buffer solutions, visual color changes were observed, where the films became reddish at acidic pH and bluish at basic pH. The ΔE* values were greater than 3, suggesting a visually perceptible change to the human eye. The samples with fruit bleaching (CB) were visually darker (lower luminance values), while the samples without bleaching (SB) had a lighter color and higher brightness, represented by larger L* values. These results indicate the potential of blueberry powder as a pH indicator for intelligent food packaging or even for sensing food deterioration. Copyright © 2017 Elsevier B.V. All rights reserved.

Visible light carrier generation in co-doped epitaxial titanate films

Energy Technology Data Exchange (ETDEWEB)

Comes, Ryan B., E-mail: ryan.comes@pnnl.gov; Kaspar, Tiffany C.; Chambers, Scott A. [Fundamental and Computational Sciences Directorate, Pacific Northwest National Laboratory, Richland, Washington 99354 (United States); Smolin, Sergey Y.; Baxter, Jason B. [Department of Chemical and Biological Engineering, Drexel University, Philadelphia, Pennsylvania 19104 (United States); Gao, Ran [Department of Materials Science and Engineering, University of California-Berkeley, Berkeley, California 94720 (United States); Apgar, Brent A. [Department of Materials Science and Engineering, University of California-Berkeley, Berkeley, California 94720 (United States); Department of Materials Science and Engineering, University of Illinois at Urbana-Champaign, Champaign, Illinois 61801 (United States); Martin, Lane W. [Department of Materials Science and Engineering, University of California-Berkeley, Berkeley, California 94720 (United States); Materials Science Division, Lawrence Berkeley National Laboratory, Berkeley, California 94720 (United States); Bowden, Mark E. [Environmental Molecular Sciences Laboratory, Pacific Northwest National Laboratory, Richland, Washington 99354 (United States)

2015-03-02

Perovskite titanates such as SrTiO{sub 3} (STO) exhibit a wide range of important functional properties, including ferroelectricity and excellent photocatalytic performance. The wide optical band gap of titanates limits their use in these applications; however, making them ill-suited for integration into solar energy harvesting technologies. Our recent work has shown that by doping STO with equal concentrations of La and Cr, we can enhance visible light absorption in epitaxial thin films while avoiding any compensating defects. In this work, we explore the optical properties of photoexcited carriers in these films. Using spectroscopic ellipsometry, we show that the Cr{sup 3+} dopants, which produce electronic states immediately above the top of the O 2p valence band in STO reduce the direct band gap of the material from 3.75 eV to 2.4–2.7 eV depending on doping levels. Transient reflectance spectroscopy measurements are in agreement with the observations from ellipsometry and confirm that optically generated carriers are present for longer than 2 ns. Finally, through photoelectrochemical methylene blue degradation measurements, we show that these co-doped films exhibit enhanced visible light photocatalysis when compared to pure STO.

The electrical, optical, structural and thermoelectrical characterization of n- and p-type cobalt-doped SnO2 transparent semiconducting films prepared by spray pyrolysis technique

International Nuclear Information System (INIS)

Bagheri-Mohagheghi, Mohammad-Mehdi; Shokooh-Saremi, Mehrdad

2010-01-01

The electrical, optical and structural properties of Cobalt (Co) doped SnO 2 transparent semiconducting thin films, deposited by the spray pyrolysis technique, have been studied. The SnO 2 :Co films, with different Co-content, were deposited on glass substrates using an aqueous-ethanol solution consisting of tin and cobalt chlorides. X-ray diffraction studies showed that the SnO 2 :Co films were polycrystalline only with tin oxide phases and preferential orientations along (1 1 0) and (2 1 1) planes and grain sizes in the range 19-82 nm. Optical transmittance spectra of the films showed high transparency ∼75-90% in the visible region, decreasing with increase in Co-doping. The optical absorption edge for undoped SnO 2 films was found to be 3.76 eV, while for higher Co-doped films shifted toward higher energies (shorter wavelengths) in the range 3.76-4.04 eV and then slowly decreased again to 4.03 eV. A change in sign of the Hall voltage and Seebeck coefficient was observed for a specific acceptor dopant level ∼11.4 at% in film and interpreted as a conversion from n-type to p-type conductivity. The thermoelectric electro-motive force (e.m.f.) of the films was measured in the temperature range 300-500 K and Seebeck coefficients were found in the range from -62 to +499 μVK -1 for various Co-doped SnO 2 films.

The electrical, optical, structural and thermoelectrical characterization of n- and p-type cobalt-doped SnO 2 transparent semiconducting films prepared by spray pyrolysis technique

Science.gov (United States)

Bagheri-Mohagheghi, Mohammad-Mehdi; Shokooh-Saremi, Mehrdad

2010-10-01

The electrical, optical and structural properties of Cobalt (Co) doped SnO 2 transparent semiconducting thin films, deposited by the spray pyrolysis technique, have been studied. The SnO 2:Co films, with different Co-content, were deposited on glass substrates using an aqueous-ethanol solution consisting of tin and cobalt chlorides. X-ray diffraction studies showed that the SnO 2:Co films were polycrystalline only with tin oxide phases and preferential orientations along (1 1 0) and (2 1 1) planes and grain sizes in the range 19-82 nm. Optical transmittance spectra of the films showed high transparency ∼75-90% in the visible region, decreasing with increase in Co-doping. The optical absorption edge for undoped SnO 2 films was found to be 3.76 eV, while for higher Co-doped films shifted toward higher energies (shorter wavelengths) in the range 3.76-4.04 eV and then slowly decreased again to 4.03 eV. A change in sign of the Hall voltage and Seebeck coefficient was observed for a specific acceptor dopant level ∼11.4 at% in film and interpreted as a conversion from n-type to p-type conductivity. The thermoelectric electro-motive force (e.m.f.) of the films was measured in the temperature range 300-500 K and Seebeck coefficients were found in the range from -62 to +499 μVK -1 for various Co-doped SnO 2 films.

Sensors of the gas CO in thin film of SnO2:Cu

International Nuclear Information System (INIS)

Tirado G, S.; Sanchez Z, F. E.

2011-10-01

Thin films of SnO 2 :Cu with different thickness, were deposited on soda-lime glass substrates and prepared by the Sol-gel process and repeated immersion. The sensor properties of these films to the gas CO for the range of 0-200 ppm in the gas concentration and operating to temperatures of 23, 100, 200, and 300 C were studied. Prepared films of pure SnO 2 were modified superficially with 1, 3, 5 and 10 layers of the catalyst Cu (SnO 2 :Cu) with the purpose of studying the effect on the sensor capacity of the gas CO by part of the films SnO 2 :Cu. Using the changes in the electric properties of the films with the incorporation of the different copper layers and experimental conditions, the sensor modifications of the gas CO were evaluated. To complete this study, was realized a characterization of the superficial morphology of the films by scanning electron microscopy and atomic force microscopy, equally was studied their structure and their electric and optical properties. (Author)

Thin (111) oriented CoFe{sub 2}O{sub 4} and Co{sub 3}O{sub 4} films prepared by decomposition of layered cobaltates

Energy Technology Data Exchange (ETDEWEB)

Buršík, Josef, E-mail: bursik@iic.cas.cz [Institute of Inorganic Chemistry of the Academy of Sciences of the Czech Republic, v.v.i., 250 68 Husinec-Řež 1001 (Czech Republic); Soroka, Miroslav, E-mail: soroka@iic.cas.cz [Institute of Inorganic Chemistry of the Academy of Sciences of the Czech Republic, v.v.i., 250 68 Husinec-Řež 1001 (Czech Republic); Uhrecký, Róbert, E-mail: uhrecky@iic.cas.cz [Institute of Inorganic Chemistry of the Academy of Sciences of the Czech Republic, v.v.i., 250 68 Husinec-Řež 1001 (Czech Republic); Kužel, Radomír, E-mail: kuzel@karlov.mff.cuni.cz [Charles University in Prague, Faculty of Mathematics and Physics, Ke Karlovu 5, 121 16 Praha 2 (Czech Republic); Mika, Filip, E-mail: filip.mika@isibrno.cz [Institute of Scientific Instruments, Academy of Sciences of the Czech Republic, v.v.i., Královopolská 147, 612 64 Brno (Czech Republic); Huber, Štěpán, E-mail: stepan.huber@vscht.cz [University of Chemistry and Technology, Faculty of Chemical Technology, Technická 5, 166 28 Prague 6 (Czech Republic)

2016-07-15

Graphical abstract: Pole figures of NaCoO{sub 2} (left) and of CoFe{sub 2}O{sub 4} (right) films formed through the transformation of O3-type NaCoO{sub 2} phase in consequence of sodium deintercalation occurring at 800 °C. Films were prepared by chemical solution deposition on MgO(111) substrate. - Highlights: • Epitaxial Na(CoFe)O{sub 2} thin films by means of chemical solution deposition were prepared. • Oriented spinel films through transformation of Na(CoFe)O{sub 2} were obtained. • Orientation relation to MgO, SrTiO{sub 3} and Zr(Y)O{sub 2} substrates were determined. • Structural aspects of Na(CoFe)O{sub 2} → CoFe{sub 2}O{sub 4} transformation pathway were elucidated. - Abstract: The formation and structural characterization of highly (111)-oriented Co{sub 3}O{sub 4} and CoFe{sub 2}O{sub 4} films prepared by a novel procedure from 00l-oriented NaCoO{sub 2} and Na(CoFe)O{sub 2} is reported. The Na(CoFe)O{sub 2} films were deposited on MgO, SrTiO{sub 3}, LaAlO{sub 3}, and Zr(Y)O{sub 2} single crystals with (100) and (111) orientations by chemical solution deposition method and crystallized at 700 °C. Subsequently they were transformed into (111)-oriented spinel phase during post-growth annealing at 800–1000 °C. Morphology and structure of the films was investigated by means of scanning electron microscopy and X-ray diffraction. While all spinel films exhibit pronounced out-of-plane orientation irrespective of substrate, the rate of in-plane orientation strongly depend on lattice misfit values. Different epitaxial phenomena ranging from true one-to-one epitaxy to the existence of many-to-one epitaxy involving two or more orientations were determined by full 3D texture analysis.

Phase transitions in LiCoO2 thin films prepared by pulsed laser deposition

International Nuclear Information System (INIS)

Huang Rong; Hitosugi, Taro; Fisher, Craig A.J.; Ikuhara, Yumi H.; Moriwake, Hiroki; Oki, Hideki; Ikuhara, Yuichi

2012-01-01

Highlights: ► Epitaxial LiCoO 2 thin films were formed on the Al 2 O 3 (0 0 0 1) substrate by PLD at room temperature and annealed at 600 °C in air. ► The orientation relationship between film and substrate is revealed. ► Crystalline phases in the RT deposited and annealed thin films are clearly identified. ► Atomic level interface structure indicates an interface reaction during annealing. ► A phase transition mechanism from fully disordered LiCoO 2 to fully ordered LiCoO 2 is proposed. - Abstract: Microstructures of epitaxial LiCoO 2 thin films formed on the (0 0 0 1) surface of sapphire (α-Al 2 O 3 ) substrates by pulsed laser deposition at room temperature and annealed at 600 °C in air were investigated by a combination of selected-area electron diffraction, high-resolution transmission electron microscopy, spherical-aberration-corrected high-angle annular dark-field scanning transmission electron microscopy, and electron energy-loss spectroscopy. As-deposited LiCoO 2 thin films consisted of epitaxial grains of the fully cation-disordered phase (γ) with a cubic rock-salt structure. During annealing, this cubic-structured phase transformed into the fully ordered trigonal (α) phase oriented with its basal plane parallel to the surface of the sapphire substrate. Although overall the film appeared to be a single crystal, a small number of Co 3 O 4 grains were also observed in annealed thin films, indicating that some Li and O had been lost during processing. The atomically sharp interface between the film and substrate also became rougher during annealing, with step defects being formed, suggesting that a localized reaction occurred at the interface.

Exceptionally High Efficient Co-Co2P@N, P-Codoped Carbon Hybrid Catalyst for Visible Light-Driven CO2-to-CO Conversion.

Science.gov (United States)

Fu, Wen Gan

2018-05-02

Artificial photosynthesis has attracted wide attention, particularly the development of efficient solar light-driven methods to reduce CO2 to form energy-rich carbon-based products. Because CO2 reduction is an uphill process with a large energy barrier, suitable catalysts are necessary to achieve this transformation. In addition, CO2 adsorption on a catalyst and proton transfer to CO2 are two important factors for the conversion reaction，and catalysts with high surface area and more active sites are required to improve the efficiency of CO2 reduction. Here, we report a visible light-driven system for CO2-to-CO conversion that consists of a heterogeneous hybrid catalyst of Co and Co2P nanoparticles embedded in carbon nanolayers codoped with N and P (Co-Co2P@NPC) and a homogeneous Ru(II)-based complex photosensitizer. The average generation rate of CO of the system was up to 35,000 μmol h-1 g-1 with selectivity of 79.1% in 3 h. Linear CO production at an exceptionally high rate of 63,000 μmol h-1 g-1 was observed in the first hour of reaction. Inspired by this highly active catalyst, we also synthesized Co@NC and Co2P@NPC materials and explored their structure, morphology, and catalytic properties for CO2 photoreduction. The results showed that the nanoparticle size, partially adsorbed H2O molecules on the catalyst surface, and the hybrid nature of the systems influenced their photocatalytic CO2 reduction performance. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Structure and magnetism of ultrathin Co and Fe films epitaxially grown on Pd/Cu(0 0 1)

International Nuclear Information System (INIS)

Lu, Y.F.; Przybylski, M.; Yan, L.; Barthel, J.; Meyerheim, H.L.; Kirschner, J.

2005-01-01

A contribution originating from the Co/Pd and Fe/Pd interfaces to the magneto-optical Kerr effect (MOKE) rotation is analyzed for Co and/or Fe films grown on a Pd-buffer-monolayer on Cu(0 0 1). A clear increase of the MOKE signal in comparison to the Co(Fe) films grown directly on Cu(0 0 1) is detected. An interpretation is supported by similar observations for Co films grown on Pd(1 1 0) and Pd(0 0 1). In particular, the sign reversal of the Kerr loops with increasing thickness of the Co(Fe) films is discussed. Magneto-optical effects are separated from the real magnetization and its dependence on the film thickness

Investigation of Ni@CoO core-shell nanoparticle films synthesized by sequential layer deposition

International Nuclear Information System (INIS)

Spadaro, M.C.; Luches, P.; Benedetti, F.; Valeri, S.; Turchini, S.; Bertoni, G.; Ferretti, A.M.; Capetti, E.; Ponti, A.; D’Addato, S.

2017-01-01

Highlights: • We studied Ni/CoO core-shell nanoparticles (NP) obtained with a gas aggregation source. • The NP oxide shells were produced bye reactive deposition of Co in Oxygen atmosphere (p_O_2 ≈ 10"−"7 mbar). • XPS, SEM, STEM were used to obtain information on Ni chemical state and NP structure and morphology. • XMCD result showed evidence of remanent magnetization at room temperature. • We interpret XMCD results as due to stabilization induced by exchange bias due to AFM/FM coupling at the core/shell interface. - Abstract: Films of Ni@CoO core-shell nanoparticles (NP Ni core size d ≈ 11 nm) have been grown on Si/SiO_x and lacey carbon supports, by a sequential layer deposition method: a first layer of CoO was evaporated on the substrate, followed by the deposition of a layer of pre-formed, mass-selected Ni NPs, and finally an overlayer of CoO was added. The Ni NPs were formed by a magnetron gas aggregation source, and mass selected with a quadrupole mass filter. The morphology of the films was investigated with Scanning Electron Microscopy and Scanning Transmission Electron Microscopy. The Ni NP cores have a shape compatible with McKay icosahedron, caused by multitwinning occurring during their growth in the source, and the Ni NP layer shows the typical random paving growth mode. After the deposition of the CoO overlayer, CoO islands are observed, gradually extending and tending to merge with each other, with the formation of shells that enclose the Ni NP cores. In situ X-ray Photoelectron Spectroscopy showed that a few Ni atomic layers localized at the core-shell interface are oxidized, hinting at the possibility of creating an intermediate NiO shell between Ni and CoO, depending on the deposition conditions. Finally, X-ray Magnetic Circular Dichroism at the Ni L_2_,_3 absorption edge showed the presence of magnetization at room temperature even at remanence, revealing the possibility of magnetic stabilization of the NP film.

Variable substrate temperature deposition of CoFeB film on Ta for manipulating the perpendicular coercive forces

Energy Technology Data Exchange (ETDEWEB)

Lakshmanan, Saravanan; Rao, Subha Krishna [Nanotechnology Research Centre, SRM University, Kattankulathur, Chennai 603203 (India); Muthuvel, Manivel Raja [Defence Metallurgical Research Laboratory (DMRL), Hyderabad 500058 (India); Chandrasekaran, Gopalakrishnan [Nanotechnology Research Centre, SRM University, Kattankulathur, Chennai 603203 (India); Therese, Helen Annal, E-mail: helen.a@ktr.srmuniv.ac.in [Nanotechnology Research Centre, SRM University, Kattankulathur, Chennai 603203 (India)

2017-08-01

Highlights: • Ta/CoFeB(50 nm)/Ta thin films were deposited at various substrate temperatures (T{sub s}). • CoFeB films deposited at T{sub s} such as RT, 450 °C, 475 °C and 500 °C exhibited perpendicular coercivity. • CoFeB deposited at 475 °C displayed a higher coercivity of 315 Oe and a low M{sub s} of 169 emu/cc. • The enhanced crystallization of CoFeB at the Ta/CoFeB interface results in higher H{sub c} (⟂). - Abstract: Magnetization of Ta/CoFeB/Ta trilayer films with thick layer of CoFeB deposited under different substrate temperatures (T{sub s}) via ultra-high vacuum DC sputtering technique has been measured with the applied magnetic field parallel and perpendicular to the plane of the film respectively to study the perpendicular coercive forces of the film. The samples were further analyzed for its structural, topological, morphological, and electrical transport properties. The core chemical states for the elements present in the CoFeB thin film were analyzed by XPS studies. Magnetization studies reveal the existence of perpendicular coercive forces in CoFeB films deposited only at certain temperatures such as RT, 450 °C, 475 °C and 500 °C. CoFeB film deposited at 475 °C exhibited a maximum coercivity of 315 Oe and a very low saturation magnetization (M{sub s}) of 169 emu/cc in perpendicular direction. This pronounced effect in perpendicular coercive forces observed for CoFeB475 could be attributed to the effect of temperature in enhancing the crystallization of the film at the Ta/CoFeB interfaces. However at temperatures higher than 475 °C the destruction of the Ta/CoFeB interface due to intermixing of Ta and CoFeB results in the disappearance of magnetic anisotropy.

Cycling-induced degradation of LiCoO2 thin-film cathodes at elevated temperature

International Nuclear Information System (INIS)

Van Sluytman, J.S.; West, W.C.; Whitacre, J.F.; Alamgir, F.M.; Greenbaum, S.G.

2006-01-01

The cycle life of LiCoO 2 -based all solid-state thin-film cells has been studied at room temperature, and at elevated temperatures of 50, 100, and 150 deg. C. X-ray diffraction, as well as Raman analysis, has been used to complement the electrochemical data in examining structural and chemical changes. XRD and Raman spectroscopy data indicate that elevated temperature soaks of the thin-film batteries in the quiescent state causes no discernable changes in the LiCoO 2 cathode layer. However, when the thin-film batteries are cycled at elevated temperatures, decreases in average grain size of the LiCoO 2 film occur with dramatic concomitant charge and discharge capacity loss

Influence of temperature on thermoelectric properties of Fe{sub x}Co{sub 1−x}S{sub 2} thin films: A semiconductor to semimetal conversion

Energy Technology Data Exchange (ETDEWEB)

Clamagirand, J.M.; Ares, J.R., E-mail: joser.ares@uam.es; Flores, E.; Diaz-Chao, P.; Leardini, F.; Ferrer, I.J.; Sánchez, C.

2016-02-01

In this work, we investigate the thermoelectric properties of p and n-type thin films obtained by cobalt doping of FeS{sub 2}. Films were synthesized by direct sulfuration of Co–Fe thin bilayers at 300 °C. It is found that at room temperature (RT), the Seebeck coefficient is reduced from 80 μV/K to − 70 μV/K when Co concentration is increased and the electrical resistivity of the films is decreased two orders of magnitude. X-ray diffraction and Raman measurements point out that Co is replacing Fe into the pyrite lattice and, subsequently is promoting a semiconductor to semimetal conversion. The influence of temperature on transport properties of different Fe{sub x}Co{sub 1−x}S{sub 2} films has been investigated. Whereas the Seebeck coefficient is hardly modified, the film resistivity is drastically decreased when temperature increases what has been attributed to the thermal activation of electrical carriers. The influence of Co doping on the band scheme of FeS{sub 2} is shown. To this aim, donor and acceptor states are included into its forbidden gap. Whereas the band scheme of FeS{sub 2} exhibits an acceptor level with an E = 0.11 ± 0.03 eV above the top of the valence band due to iron vacancies, a wide donor level close to the bottom of the conduction band (E = 0.08 ± 0.05 eV) is created by the progressive replacement of iron by cobalt into the FeS{sub 2} lattice. - Highlights: • Thermoelectric properties of pyrite and Co-doped pyrite thin films were measured. • Whereas ρ decreases, S remains practically unaltered on increasing temperature (RT-300 °C). • On increasing Co-concentration, films exhibit a p semiconductor to n type semimetal conversion. • Donor states close to the botton of the conduction band are created by Co doping. • Energy of the donor level decreases and gets wider due to Co-concentration.

Imidazopyridine/Pyrrole and hydroxybenzimidazole/pyrrole pairs for DNA minor groove recognition.

Science.gov (United States)

Renneberg, Dorte; Dervan, Peter B

2003-05-14

The DNA binding properties of fused heterocycles imidazo[4,5-b]pyridine (Ip) and hydroxybenzimidazole (Hz) paired with pyrrole (Py) in eight-ring hairpin polyamides are reported. The recognition profile of Ip/Py and Hz/Py pairs were compared to the five-membered ring pairs Im/Py and Hp/Py on a DNA restriction fragment at four 6-base pair recognition sites which vary at a single position 5'-TGTNTA-3', where N = G, C, T, A. The Ip/Py pair distinguishes G.C from C.G, T.A, and A.T, and the Hz/Py pair distinguishes T.A from A.T, G.C, and C.G, affording a new set of heterocycle pairs to target the four Watson-Crick base pairs in the minor groove of DNA.

Development of technology for the large-scale preparation of 60Co polymer film source

International Nuclear Information System (INIS)

Udhayakumar, J.; Pardeshi, G.S.; Gandhi, Shymala S.; Chakravarty, Rubel; Kumar, Manoj; Dash, Ashutosh; Venkatesh, Meera

2008-01-01

60 Co sources (∼37 kBq) in the form of a thin film are widely used in position identification of perforation in offshore oil-well explorations. This paper describes the large-scale preparation of such sources using a radioactive polymer containing 60 Co. 60 Co was extracted into chloroform containing 8-hydroxyquinoline. The chloroform layer was mixed with polymethyl methacrylate (PMMA) polymer. A large film was prepared using the polymer solution containing the complex. The polymer film was then cut into circular sources, mounted on a source holder and supplied to various users

An insight in the structural, morphological, electrical and optical properties of spray pyrolysed Co{sub 3}O{sub 4} thin films

Energy Technology Data Exchange (ETDEWEB)

Victoria, S. Grace, E-mail: grace_fletcher2007@yahoo.co.in [Department of Physics, Women' s Christian College, Nagercoil 629 001 (India); Ezhil Raj, A. Moses [Department of Physics & Research Centre, Scott Christian College (Autonomous), Nagercoil 629 003 (India); Ravidhas, C. [Department of Physics, Bishop Heber College (Autonomous), Tiruchirappalli 620 017 (India)

2015-07-15

The spray pyrolysis deposition of stable and single phase cobalt oxide (Co{sub 3}O{sub 4}) thin films at three different deposition temperatures viz. 350 °C, 420 °C and 470 °C was undertaken in the present work. It was found that substrate temperature played a pivotal role in obtaining pure thin layers. X-ray diffraction analysis confirmed the cubic spinel type structure (a = 8.094 Å) of polycrystalline Co{sub 3}O{sub 4} with predominant orientation along (311) plane. The average crystallite size was found to be around 49 nm. Fourier transform IR spectra revealed the presence of an OB{sub 3} vibration at 540 cm{sup −1} and an ABO{sub 3} vibration at 640 cm{sup −1} where, B denotes Co{sup 3+} ions in an octahedral hole and A denotes Co{sup 2+} ions in a tetrahedral hole. The Raman spectra recorded in the wave number range 200–800 cm{sup −1} indicated five Raman peaks and the strong characteristic peak at 694 cm{sup −1} was assigned to the A{sub 1g} mode which corresponds to Co–O breathing vibration of Co{sup 2+} ions in tetrahedral coordination. Surface analysis was carried out with the aid of SEM and AFM. The formation of Co{sub 3}O{sub 4} was confirmed by analyzing the binding energies and intensities of Co 3s, Co 2p and O 1s obtained from XPS. Temperature dependent resistivity was realized from the two probe electrical measurements validating the semiconducting behaviour of the prepared films. Co{sub 3}O{sub 4} films had low transmittance values in the order of 23%–43% in the UV–Vis-NIR region. Estimation through Tauc plots revealed direct optical band gap energies around 2–2.24 eV due to charge transfer transition between p states of O{sup 2−} and t{sub 2} states of Co{sup 2+}. Related optical parameters like extinction coefficient (k) and refractive index (μ) were calculated using Swanepoel method. - Graphical abstract: Display Omitted - Highlights: • Position of the obtained diffraction peaks coincided well with the standard cubic

Growth and giant coercive field of spinel-structured Co3- x Mn x O4 thin films

Science.gov (United States)

Kwak, Yongsu; Song, Jonghyun; Koo, Taeyeong

2016-08-01

We grew epitaxial thin films of CoMn2O4 and Co2MnO4 on Nb-doped SrTiO3(011) and SrTiO3(001) single crystal substrates using pulsed laser deposition. The magnetic Curie temperature ( T c ) of the Co2MnO4 thin films was ~176 K, which is higher than that of the bulk whereas CoMn2O4 thin films exhibited a value of T c (~151 K) lower than that of the bulk. For the Co2MnO4 thin films, the M - H loop showed a coercive field of ~0.7 T at 10 K, similar to the value for the bulk. However, the M -H loop of the CoMn2O4(0 ll) thin film grown on a Nb-doped SrTiO3(011) substrate exhibited a coercive field of ~4.5 T at 30 K, which is significantly higher than those of the Co2MnO4 thin film and bulk. This giant coercive field, only observed for the CoMn2O4(0 ll) thin film, can be attributed to the shape anisotropy and strong spin-orbit coupling.

Thermoelectric properties of Nd0.75Sr1.25CoO4 thin films

International Nuclear Information System (INIS)

Huang, S.L.; Ruan, K.Q.; Jiao, X.L.; Wu, H.Y.; Lv, Z.M.; Pang, Z.Q.; Liu, J.; Yang, H.S.; Wu, W.B.; Cao, L.Z.; Li, X.G.

2007-01-01

Temperature dependence of the electrical resistivity (ρ) and thermopower (S) in the ab-plane of Nd 0.75 Sr 1.25 CoO 4 thin films have been investigated systematically in the temperature range 70 K< T<310 K. The specimen presents a p-type semiconducting transport property. The S nearly keeps constant at high temperatures and decreases at low ones with an additional step-like decrease, which was argued to be intimately related with the magnetic properties of the specimen. The resistivity follows the Arrhenius law. And the large value of the power factor suggests the films may be a good candidate for the thermoelectric material

Effect of the CO2/SiH4 Ratio in the p-μc-SiO:H Emitter Layer on the Performance of Crystalline Silicon Heterojunction Solar Cells

Directory of Open Access Journals (Sweden)

Jaran Sritharathikhun

2014-01-01

Full Text Available This paper reports the preparation of wide gap p-type hydrogenated microcrystalline silicon oxide (p-μc-SiO:H films using a 40 MHz very high frequency plasma enhanced chemical vapor deposition technique. The reported work focused on the effects of the CO2/SiH4 ratio on the properties of p-μc-SiO:H films and the effectiveness of the films as an emitter layer of crystalline silicon heterojunction (c-Si-HJ solar cells. A p-μc-SiO:H film with a wide optical band gap (E04, 2.1 eV, can be obtained by increasing the CO2/SiH4 ratio; however, the tradeoff between E04 and dark conductivity must be considered. The CO2/SiH4 ratio of the p-μc-SiO:H emitter layer also significantly affects the performance of the solar cells. Compared to the cell using p-μc-Si:H (CO2/SiH4 = 0, the cell with the p-μc-SiO:H emitter layer performs more efficiently. We have achieved the highest efficiency of 18.3% with an open-circuit voltage (Voc of 692 mV from the cell using the p-μc-SiO:H layer. The enhancement in the Voc and the efficiency of the solar cells verified the potential of the p-μc-SiO:H films for use as the emitter layer in c-Si-HJ solar cells.

Superconductivity in Na{sub 1-x}CoO{sub 2}.yH{sub 2}O thin films

Energy Technology Data Exchange (ETDEWEB)

Hildebrandt, Sandra; Komissinkiy, Philipp; Alff, Lambert [Institute for Materials Science, TU Darmstadt (Germany); Fritsch, Ingo; Habermeier, Hanns-Ulrich [Max-Planck-Institute for Solid State Research, Stuttgart (Germany); Lemmens, Peter [Institute for Condensed Matter Physics, TU Braunschweig (Germany)

2010-07-01

Sodium cobaltate (Na{sub 1-x}CoO{sub 2}) is a novel material with thermoelectric behavior, charge and spin ordered states dependent on the sodium content in the composition. A superconducting phase was found in water intercalated sodium cobaltate (Na{sub 1-x}CoO{sub 2}.yH{sub 2}O) with x=0.65-0.7 and y=0.9-1.3. The pairing state is still under debate, but there are some indications for a spin-triplet or p-wave superconducting pairing state. First films of Na{sub 1-x}CoO{sub 2}.yH{sub 2}O with a superconducting transition temperature near 5 K have been successfully grown. Here we report on thin films of Na{sub 1-x}CoO{sub 2} grown by pulsed laser deposition technique. The deposition parameters, sodium deintercalation and water intercalation conditions are tuned in order to obtain the superconducting phase. The instability of this phase might be an indication for triplet superconductivity, which is known to be affected strongly by impurities and defects.This observation is in agreement with the fact that so far also no superconducting thin films of the most famous triplet superconductor Sr{sub 2}RuO{sub 4} have been reported.

Variable substrate temperature deposition of CoFeB film on Ta for manipulating the perpendicular coercive forces

Science.gov (United States)

Lakshmanan, Saravanan; Rao, Subha Krishna; Muthuvel, Manivel Raja; Chandrasekaran, Gopalakrishnan; Therese, Helen Annal

2017-08-01

Magnetization of Ta/CoFeB/Ta trilayer films with thick layer of CoFeB deposited under different substrate temperatures (Ts) via ultra-high vacuum DC sputtering technique has been measured with the applied magnetic field parallel and perpendicular to the plane of the film respectively to study the perpendicular coercive forces of the film. The samples were further analyzed for its structural, topological, morphological, and electrical transport properties. The core chemical states for the elements present in the CoFeB thin film were analyzed by XPS studies. Magnetization studies reveal the existence of perpendicular coercive forces in CoFeB films deposited only at certain temperatures such as RT, 450 °C, 475 °C and 500 °C. CoFeB film deposited at 475 °C exhibited a maximum coercivity of 315 Oe and a very low saturation magnetization (Ms) of 169 emu/cc in perpendicular direction. This pronounced effect in perpendicular coercive forces observed for CoFeB475 could be attributed to the effect of temperature in enhancing the crystallization of the film at the Ta/CoFeB interfaces. However at temperatures higher than 475 °C the destruction of the Ta/CoFeB interface due to intermixing of Ta and CoFeB results in the disappearance of magnetic anisotropy.

Effects of surfactants on microwave-assisted solid-state intercalation of poly(carbazole) in Bentonite

International Nuclear Information System (INIS)

Riaz, Ufana; Ashraf, S. M.; Khan, Nisha

2011-01-01

The present preliminary investigation reports, for the first time, the effects of typical cationic and anionic surfactants on the microwave-assisted solid-state intercalation and polymerization of carbazole (Cz) in the basal spacings of Bentonite. The intercalation of cetyl pyridinium chloride (CPCl), a cationic surfactant, and naphthalene sulfonic acid (NSA), an anionic surfactant, in Bentonite was carried out at two loadings—25 and 50 wt%—using microwave irradiation. The in situ polymerization of Cz was successfully carried out into the surfactant-modified galleries of Bentonite. This was confirmed by Gel permeation chromatography (GPC). The intercalation of poly(carbazole) (PCz) was confirmed by FT-IR, UV–Visible, and XRD analyses. Although polymerization was carried out in the solid-state, the UV–Visible spectra revealed the doped state of PCz and the presence of a charge carrier tail. The XRD studies showed that the increase in the height of the galleries was higher in case of Bentonite/CPCl/PCz nanocomposites as compared to Bentonite/NSA/PCz nanocomposites. It also revealed different orientations of the two surfactants in the galleries of the clay. The average particle size of Bentonite/CPCl/PCz (1:0.25:0.25) and (1:0.5:0.5) nanocomposites was found to be in the range of 25–35 and 50–60 nm, respectively. The Bentonite/NSA/PCz (1:0.25:0.25) and (1:0.5:0.5) nanocomposites showed the average particle size in the range of 20–30 nm and 40–50 nm, respectively. The results revealed that both cationic and anionic surfactants strongly influenced the morphology of Bentonite/PCz nanocomposites. The difference in the mechanisms of solid-state intercalation of PCz in the presence of these surfactants has been proposed.

Effect of Co doping concentration on structural properties and optical parameters of Co-doped ZnO thin films by sol-gel dip-coating method.

Science.gov (United States)

Nam, Giwoong; Yoon, Hyunsik; Kim, Byunggu; Lee, Dong-Yul; Kim, Jong Su; Leem, Jae-Young

2014-11-01

The structural and optical properties of Co-doped ZnO thin films prepared by a sol-gel dip-coating method were investigated. X-ray diffraction analysis showed that the thin films were grown with a c-axis preferred orientation. The position of the (002) peak was almost the same in all samples, irrespective of the Co concentration. It is thus clear that Co doping had little effect on the position of the (002) peak. To confirm that Co2+ was substituted for Zn2+ in the wurtzite structure, optical measurements were conducted at room temperature by a UV-visible spectrometer. Three absorption peaks are apparent in the Co-doped ZnO thin films that do not appear for the undoped ZnO thin film. As the Co concentration was increased, absorption related to characteristic Co2+ transitions increased because three absorption band intensities and the area underneath the absorption wells between 500 and 700 nm increased with increasing Co concentration. The optical band gap and static dielectric constant decreased and the Urbach energy and extinction coefficient increased with increasing Co concentration.

Grinding solvent-free Paal-Knorr pyrrole synthesis on smectites as ...

African Journals Online (AJOL)

Journal Home > Vol 32, No 1 (2018) > ... An environmentally benign method for the synthesis of N-substituted pyrroles from one-pot solvent-free ... conditions make this protocol practical, environmentally friendly and economically attractive.

Conducting polymers of decanedioic acid bis-(4-pyrrol-1-yl-phenyl) ester

International Nuclear Information System (INIS)

Cirpan, A.; Guner, Y.; Toppare, L.

2004-01-01

A dipyrrolyl monomer was synthesized via the reaction between 4-pyrrol-1-yl phenol and decanedioyl dichloride. The electrochemical behavior of this monomer was studied. Polymerization of decanedioic acid bis-(4-pyrrol-1-yl-phenyl) ester (DAPE) was achieved by chemical and constant current electrolyses methods. Copolymerization of DAPE with thiophene was performed by constant potential electrolysis in acetonitrile-tetrabutylammonium tetrafluoroborate (TBAFB), dichloromethane-TBAFB, solvent-electrolyte couples. The chemical structures and properties were investigated by Fourier transform infrared spectroscopy, nuclear magnetic resonance spectroscopy, differential scanning calorimetry and thermal gravimetry analysis. The conductivities of the samples were measured by a four-probe technique

Conducting polymers of decanedioic acid bis-(4-pyrrol-1-yl-phenyl) ester

Energy Technology Data Exchange (ETDEWEB)

Cirpan, A.; Guner, Y.; Toppare, L

2004-05-15

A dipyrrolyl monomer was synthesized via the reaction between 4-pyrrol-1-yl phenol and decanedioyl dichloride. The electrochemical behavior of this monomer was studied. Polymerization of decanedioic acid bis-(4-pyrrol-1-yl-phenyl) ester (DAPE) was achieved by chemical and constant current electrolyses methods. Copolymerization of DAPE with thiophene was performed by constant potential electrolysis in acetonitrile-tetrabutylammonium tetrafluoroborate (TBAFB), dichloromethane-TBAFB, solvent-electrolyte couples. The chemical structures and properties were investigated by Fourier transform infrared spectroscopy, nuclear magnetic resonance spectroscopy, differential scanning calorimetry and thermal gravimetry analysis. The conductivities of the samples were measured by a four-probe technique.

Effect of heat treatment on interface driven magnetic properties of CoFe films

Science.gov (United States)

Singh, Akhilesh Kr.; Hsu, Jen-Hwa

2017-06-01

We report systematic studies on non-magnetic Ta underlayer and cap layer driven microstructural and magnetic properties at a wide temperature range for CoFe films. All the films were grown at room temperature and post annealed at different annealing temperatures (TA = 200 °C, 250 °C, 300 °C, 350 °C, 400 °C and 450 °C). The in-plane magnetic hysteresis (M-H) loops of 10 nm thick CoFe single layer films, grown directly on thermally oxidized Si substrate, exhibit anisotropic nature for TA above 250 °C. However, the CoFe (10 nm) films grown on the 5 nm thick Ta underlayer show reduced anisotropy. Moreover, with underlayer and cap layers (2 nm) the anisotropy is disappeared. The in-plane coercivity (HC) shows a strong variation with TA, underlayer and cap layers. HC increases significantly with Ta underlayer and cap layers. The out of plane M-H loops exhibit increase in the remanence magnetization and squareness with both Ta underlayer and cap layers due to transition of in-plane magnetization component to the out of plane direction. The atomic force microscopic observations revealed that grain/particle size and shape depend strongly on TA and Ta layers. Moreover, a large reduction in the surface roughness is observed with the Ta cap layer. The magnetic domain patterns depend on the TA, and Ta layers. However, for Ta/CoFe/Ta films no clear domains were observed for all the TA. Hence, the Ta cap layers not only protect the CoFe magnetic layer against the heat treatment, but also show a smooth surface at a wide temperature range. These results could be discussed on the basis of random anisotropy model, TA, underlayer and cap layers driven microstructure and magnetization orientation of the CoFe films.

[18F]fluoromethylated phenyl-pyrroles and 7-azaindole analog as potential dopamine D4 receptor imaging agents

International Nuclear Information System (INIS)

Ji, D. Y.; Oh, S. Z.; Choi, Y. S.; Lee, K. C.; Kim, S. E.; Choi, Y.; Lee, K. H.; Kim, B. T.

1997-01-01

An association between the dopamine D 4 receptor and schizophrenia was recently suggested and the D 4 receptor antagonists may thus have potential in elucidating the role of the receptor in schizophrenic patients. The purpose of this study was to develop some of these antagonists as potential dopamine D 4 receptor imaging agents for PET. We have prepared 1-(3-[ 18 F]fluoromethylphenyl)-3-([4-(pyridin-2-yl)piperazin-1-yl)methyl) pyrrole (1), 1-(3-[ 18 F]fluoromethylphenyl)-3-([4-(pyridin-2-yl)piperazin-1-yl)methyl) pyrrole (2), and 3-([4-(4-[ 18 F]fluoro methylbenzyl)piperazin-1-yl)methyl)-1H-pyrrolo(2,3,-b)pyridine (3) as potential imaging agents for the dopamine D 4 receptor for PET. The compounds [ 18 F]1 and [ 18 F]2 were prepared by coupling of (3-[ 18 F]fluoromethylphenyl)-pyrrol-1- yl-3-aldehyde and the piperazine moiety in the presence of NaBH 3 CN. The [ 18 F]fluorinated aldehyde was obtained in 60-85% yield by the displacement of the corresponding mesylate with F-18-(THF, 90 .deg. C, 5 min). HPLC purification (Alltech Econosil C-18 columm, 250 x 10 mm, 35: 65 = 0.1M NH 4 CI 2 H : CH 3 OH, 4 ml/min, t R =26.6 min) gave the [ 18 F]1 and [ 18 F]2 in 7-12% yield. In the case of azaindole 3, a methlene link was inserted between the piperazinyl and a fluoromethyl phenyl group. Radiochemical synthesis of the [ 18 F]3 was carried out by coupling of the piperazne moiety and [ 18 F]fluoromethylbenzyl mesylate in the presence of NEt 3 (3:1-CH 3 CN: DMF, 120 .deg. C, 30 min). Purification was carried out by HPLC using a C-18 column (Alltech Econosil, 50 x 10 mm, 100% 0.1M NH 4 CO 2 H for 5 min followed by 40:60=0.1 M NH 4 CO 2 H : MeOH, 4 ml/min t R =28.7 min). The time of synthesis including HPLC purification was 100 min. The overall yield of [ 18 F]3 was 10-15% with a radiochemical purity better than 97% and a specific activity greater than 1000 ci/mmol

Multi-jump magnetic switching in ion-beam sputtered amorphous Co20Fe60B20 thin films

International Nuclear Information System (INIS)

Raju, M.; Chaudhary, Sujeet; Pandya, D. K.

2013-01-01

Unconventional multi-jump magnetization reversal and significant in-plane uniaxial magnetic anisotropy (UMA) in the ion-beam sputtered amorphous Co 20 Fe 60 B 20 (5–75 nm) thin films grown on Si/amorphous SiO 2 are reported. While such multi-jump behavior is observed in CoFeB(10 nm) film when the magnetic field is applied at 10°–20° away from the easy-axis, the same is observed in CoFeB(12.5 nm) film when the magnetic field is 45°–55° away from easy-axis. Unlike the previous reports of multi-jump switching in epitaxial films, their observance in the present case of amorphous CoFeB is remarkable. This multi-jump switching is found to disappear when the films are crystallized by annealing at 420 °C. The deposition geometry and the energy of the sputtered species appear to intrinsically induce a kind of bond orientation anisotropy in the films, which leads to the UMA in the as-grown amorphous CoFeB films. Exploitation of such multi-jump switching in amorphous CoFeB thin films could be of technological significance because of their applications in spintronic devices

Ferromagnetic resonance spectroscopy of CoFeZr-Al{sub 2}O{sub 3} granular films containing “FeCo core – oxide shell” nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Kołtunowicz, Tomasz N., E-mail: t.koltunowicz@pollub.pl [Department of Electrical Devices and High Voltage Technology, Lublin University of Technology, Nadbystrzycka 38a, 20-618 Lublin (Poland); Zukowski, Pawel [Department of Electrical Devices and High Voltage Technology, Lublin University of Technology, Nadbystrzycka 38a, 20-618 Lublin (Poland); Sidorenko, Julia [Department of Semiconductors Physics and Nanoelectronics, Belarusian State University, Independence Av. 4, 220030 Minsk (Belarus); Bayev, Vadim; Fedotova, Julia A. [Institute for Nuclear Problems, Belarusian State University, Bobrujskaya Str. 11, 220030 Minsk (Belarus); Opielak, Marek [Institute of Transport, Combustion Engines and Ecology, Lublin University of Technology, Nadbystrzycka 36, 20-618 Lublin (Poland); Marczuk, Andrzej [Department of Transporting and Agricultural Machinery, University of Life Sciences in Lublin, Głeboka 28, 20-612 Lublin (Poland)

2017-01-01

Ferromagnetic resonance (FMR) spectroscopy is applied for comparative analysis of granular (CoFeZ){sub x}(Al{sub 2}O{sub 3}){sub 100−x}, (31 at%≤x≤47 at%) films containing pure FeCo-based nanoparticles (NPs) or “FeCo-based core – oxide shell” NPs inside Al{sub 2}O{sub 3} matrix when deposited in oxygen-free or oxygen-containing atmosphere, correspondingly. It is established that g-factor extracted from the FMR spectra of films with core–shell NPs decreases with x below the value g =2.0023 for free electron that is untypical for metallic NPs. This effect is associated with the formation of the interface between ferromagnetic core and antiferromagnetic (ferrimagnetic) oxide shell of NPs. - Highlights: • CoFeZr-Al{sub 2}O{sub 3} granular films containing “FeCo core – oxide shell” nanoparticles. • magnetic anisotropy of (CoFeZr){sub x}(Al{sub 2}O{sub 3}){sub 100−x} films is of an easy plane type. • essential difference in dependence of g-factor on metal content in non- and oxidized film. • non-oxidized samples indicates the reduction of the value of films magnetization.

Electrochemical Reduction of CO2 on Compositionally Variant Au-Pt Bimetallic Thin Films

DEFF Research Database (Denmark)

Ma, Ming; Hansen, Heine Anton; Valenti, Marco

2017-01-01

The electrocatalytic reduction of CO2 on Au-Pt bimetallic catalysts with different compositions was evaluated, offering a platform for uncovering the correlation between the catalytic activity and the surface composition of bimetallic electrocatalysts. The Au-Pt alloy films were synthesized...... by a magnetron sputtering co-deposition technique with tunable composition. It was found that the syngas ratio (CO:H2) on the Au-Pt films is able to be tuned by systematically controlling the binary composition. This tunable catalytic selectivity is attributed to the variation of binding strength of COOH and CO...... intermediates, influenced by the surface electronic structure (d-band center energy) which is linked to the surface composition of the bimetallic films. Notably, a gradual shift of the d-band center away from the Fermi level was observed with increasing Au content, which correspondingly reduces the binding...

Application of electrosynthesized poly(aniline-co-p-aminophenol) as a catechol sensor

International Nuclear Information System (INIS)

Chen Chuanxiang; Sun Cheng; Gao Yuhua

2009-01-01

Poly(aniline-co-p-aminophenol) (copolymer) film was used as a sensor to determine the presence of catechol, taking advantage of the ability of the film to effectively catalyze the oxidation of catechol. The copolymer served as an electron transfer mediator between the electrode surface and catechol in the solution. The response current of the catechol sensor depended on the applied potential, pH and temperature at a given concentration of catechol. At optimum conditions, the catechol sensor displayed an excellent electrocatalytic response to the detection of catechol in a concentration range from 5 to 500 μM with a detection limit of 0.8 μM. The effects of selected organic compounds on the response of the catechol sensor were studied. Together, these findings show that the catechol sensor exhibits a better selectivity towards interfering species and a better operational and storage stability

Effect of heat treatment on interface driven magnetic properties of CoFe films

Energy Technology Data Exchange (ETDEWEB)

Singh, Akhilesh Kr., E-mail: drakhintu@gmail.com; Hsu, Jen-Hwa

2017-06-15

Highlights: • Ta underlayer and cap layer dependent anisotropy nature in thin CoFe films. • Thin Ta layer induces the magnetization component along normal to the film plane. • Heat treatment and Ta layers driven surface morphology, roughness and grain size. • Roughness reduces more than an order of magnitude with 2 nm Ta cap layer. • H{sub C}, domain patterns and domain size depend on Ta layers and heat treatment. - Abstract: We report systematic studies on non-magnetic Ta underlayer and cap layer driven microstructural and magnetic properties at a wide temperature range for CoFe films. All the films were grown at room temperature and post annealed at different annealing temperatures (T{sub A} = 200 °C, 250 °C, 300 °C, 350 °C, 400 °C and 450 °C). The in-plane magnetic hysteresis (M–H) loops of 10 nm thick CoFe single layer films, grown directly on thermally oxidized Si substrate, exhibit anisotropic nature for T{sub A} above 250 °C. However, the CoFe (10 nm) films grown on the 5 nm thick Ta underlayer show reduced anisotropy. Moreover, with underlayer and cap layers (2 nm) the anisotropy is disappeared. The in-plane coercivity (H{sub C}) shows a strong variation with T{sub A}, underlayer and cap layers. H{sub C} increases significantly with Ta underlayer and cap layers. The out of plane M–H loops exhibit increase in the remanence magnetization and squareness with both Ta underlayer and cap layers due to transition of in-plane magnetization component to the out of plane direction. The atomic force microscopic observations revealed that grain/particle size and shape depend strongly on T{sub A} and Ta layers. Moreover, a large reduction in the surface roughness is observed with the Ta cap layer. The magnetic domain patterns depend on the T{sub A}, and Ta layers. However, for Ta/CoFe/Ta films no clear domains were observed for all the T{sub A}. Hence, the Ta cap layers not only protect the CoFe magnetic layer against the heat treatment, but also

Effect of heat treatment on interface driven magnetic properties of CoFe films

International Nuclear Information System (INIS)

Singh, Akhilesh Kr.; Hsu, Jen-Hwa

2017-01-01

Highlights: • Ta underlayer and cap layer dependent anisotropy nature in thin CoFe films. • Thin Ta layer induces the magnetization component along normal to the film plane. • Heat treatment and Ta layers driven surface morphology, roughness and grain size. • Roughness reduces more than an order of magnitude with 2 nm Ta cap layer. • H C , domain patterns and domain size depend on Ta layers and heat treatment. - Abstract: We report systematic studies on non-magnetic Ta underlayer and cap layer driven microstructural and magnetic properties at a wide temperature range for CoFe films. All the films were grown at room temperature and post annealed at different annealing temperatures (T A = 200 °C, 250 °C, 300 °C, 350 °C, 400 °C and 450 °C). The in-plane magnetic hysteresis (M–H) loops of 10 nm thick CoFe single layer films, grown directly on thermally oxidized Si substrate, exhibit anisotropic nature for T A above 250 °C. However, the CoFe (10 nm) films grown on the 5 nm thick Ta underlayer show reduced anisotropy. Moreover, with underlayer and cap layers (2 nm) the anisotropy is disappeared. The in-plane coercivity (H C ) shows a strong variation with T A , underlayer and cap layers. H C increases significantly with Ta underlayer and cap layers. The out of plane M–H loops exhibit increase in the remanence magnetization and squareness with both Ta underlayer and cap layers due to transition of in-plane magnetization component to the out of plane direction. The atomic force microscopic observations revealed that grain/particle size and shape depend strongly on T A and Ta layers. Moreover, a large reduction in the surface roughness is observed with the Ta cap layer. The magnetic domain patterns depend on the T A , and Ta layers. However, for Ta/CoFe/Ta films no clear domains were observed for all the T A . Hence, the Ta cap layers not only protect the CoFe magnetic layer against the heat treatment, but also show a smooth surface at a wide

A colorimetric tetrathiafulvalene-calix 4 pyrrole anion sensor

DEFF Research Database (Denmark)

Nielsen, K. A.

2012-01-01

The interaction and colorimetric sensing properties of a tetrathiafulvalene substituted calix[4]pyrrole sensor with anions were investigated using H-1 NMR and absorption spectroscopic techniques. Visual color changes were observed upon addition of different anions (Cl-, Br-, CN-, and Ac......O-) to a solution of the sensor. (C) 2012 Elsevier Ltd. All rights reserved....

Triazine containing N-rich microporous organic polymers for CO2 capture and unprecedented CO2/N2 selectivity

International Nuclear Information System (INIS)

Bhunia, Subhajit; Bhanja, Piyali; Das, Sabuj Kanti; Sen, Tapas; Bhaumik, Asim

2017-01-01

Targeted synthesis of microporous adsorbents for CO 2 capture and storage is very challenging in the context of remediation from green house gases. Herein we report two novel N-rich microporous networks SB-TRZ-CRZ and SB-TRZ-TPA by extensive incorporation of triazine containing tripodal moiety in the porous polymer framework. These materials showed excellent CO 2 storage capacities: SB-TRZ-CRZ displayed the CO 2 uptake capacity of 25.5 wt% upto 1 bar at 273 K and SB-TRZ-TPA gave that of 16 wt% under identical conditions. The substantial dipole quadruple interaction between network (polar triazine) and CO 2 boosts the selectivity for CO 2 /N 2 . SB-TRZ-CRZ has this CO 2 /N 2 selectivity ratio of 377, whereas for SB-TRZ-TPA it was 97. Compared to other porous polymers, these materials are very cost effective, scalable and very promising material for clean energy application and environmental issues. - Graphical abstract: We report two novel N-rich microporous polymeric materials by doping of triazine containing tripodal dopant in the organic framework. These materials showed excellent CO 2 storage capacities as high as 25.5 wt% under 1 bar pressure with exceptional CO 2 /N 2 selectivity of 377. - Highlights: • Triazine containing trimodal moiety incorporated in polycarbazolic and poly triphenylamine networks. • N-rich crosslinked polymers with high BET surface area and 1.5–1.7 nm size large micropores. • CO 2 uptake capacity of 25.5 wt% upto 1 bar at 273 K. • These crosslinked porous polymers showed exceptional CO 2 /N 2 selectivity.

Conducting polymer film-based immunosensors using carbon nanotube/antibodies doped polypyrrole

Energy Technology Data Exchange (ETDEWEB)

Tam, Phuong Dinh, E-mail: phuongdinhtam@gmail.com [Advanced Institute for Science and Technology (AIST), Hanoi University of Science and Technology (Viet Nam); Hieu, Nguyen Van [International Training Institute for Materials Science (ITIMS), Hanoi University of Science and Technology (Viet Nam)

2011-09-15

Carbon nanotube/polypyrrole/antibodies polymer films were synthesized successfully on microelectrodes by electrochemical deposition. Electropolymerization was performed at optimal range between -0.8 and +0.8 V at a scan rate of 50 mV s{sup -1} in an electrochemical mini-cell containing monomer pyrroles, carbon nanotubes, and goat IgGs. The conducting polymer films were characterized by Fourier transform infrared spectrometry, Raman spectra, and Field emission scanning electron microscopy. And then, it was prepared for immunosensor application to determine anti-goat IgGs. The results show that a linear range between 0.05 and 0.7 {mu}g ml{sup -1} for anti-goat IgGs detection was observed for immunosensor, a detection limit as low as 0.05 {mu}g ml{sup -1} and a response time of 1 min. The effect parameters of electropolymerization process on immunosensor response are also studied. It found that the immunosensor well active in 1.5 mg ml{sup -1} CNT concentration, 2.5 mM pyrrole, 10 {mu}g ml{sup -1} goat IgGs.

Preparation and structure characterization of SmCo5(0001) epitaxial thin films grown on Cu(111) underlayers

International Nuclear Information System (INIS)

Ohtake, Mitsuru; Nukaga, Yuri; Futamoto, Masaaki; Kirino, Fumiyoshi

2009-01-01

SmCo 5 (0001) epitaxial films were prepared on Cu(111) single-crystal underlayers formed on Al 2 O 3 (0001) substrates at 500 deg. C. The nucleation and growth mechanism of (0001)-oriented SmCo 5 crystal on Cu(111) underlayer is investigated and a method to control the nucleation is proposed. The SmCo 5 epitaxial thin film formed directly on Cu underlayer consists of two types of domains whose orientations are rotated around the film normal by 30 deg. each other. By introducing a thin Co seed layer on the Cu underlayer, a SmCo 5 (0001) single-crystal thin film is successfully obtained. Nucleation of SmCo 5 crystal on Cu underlayer seems controllable by varying the interaction between the Cu underlayer and the SmCo 5 layer

Structural, linear and nonlinear optical properties of co-doped ZnO thin films

Science.gov (United States)

Shaaban, E. R.; El-Hagary, M.; Moustafa, El Sayed; Hassan, H. Shokry; Ismail, Yasser A. M.; Emam-Ismail, M.; Ali, A. S.

2016-01-01

Different compositions of Co-doped zinc oxide [(Zn(1- x)Co x O) ( x = 0, 0.02, 0.04, 0.06, 0.08 and 0.10)] thin films were evaporated onto highly clean glass substrates by thermal evaporation technique using a modified source. The structural properties investigated by X-ray diffraction revealed hexagonal wurtzite ZnO-type structure. The crystallite size of the films was found to decrease with increasing Co content. The optical characterization of the films has been carried out using spectral transmittance and reflectance obtained in the wavelength range from 300 to 2500 nm. The refractive index has been found to increase with increasing Co content. It was further found that optical energy gap decreases from 3.28 to 3.03 eV with increasing Co content from x = 0 to x = 0.10, respectively. The dispersion of refractive index has been analyzed in terms of Wemple-DiDomenico (WDD) single-oscillator model. The oscillator parameters, the single-oscillator energy ( E o), the dispersion energy ( E d), and the static refractive index ( n 0), were determined. The nonlinear refractive index of the Zn(1- x)Co x O thin films was calculated and revealed well correlation with the linear refractive index and WDD parameters which in turn depend on the density and molar volume of the system.

Hydrolytic study of the copolymer Poly pyrrole/ Polyethyleneglycol and Poly pyrrole synthesized by plasma; Estudio hidrolitico del copolimero polipirrol/polietilenglicol y polipirrol sintetizado por plasma

Energy Technology Data Exchange (ETDEWEB)

Colin, E.; Enriquez, M.A.; Olayo, M.G.; Cruz, G.J.; Carapia, L.; Romero, M. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico); Morales, J.; Olayo, R. [UAM-I, A.P. 55-534 Iztapalapa, Mexico D.F. (Mexico)

2006-07-01

In this work the study about the hydrolytic compatibility of semiconductor polymers, copolymer Poly pyrrole/ Polyethyleneglycol (PPy/PEG) and Poly pyrrole (PPy) for their possible use as biomaterials. The polymers were synthesized by plasma between 10 and 100 W, with discharges of splendor RF to 13.5 MHz with resistive coupling. The hydrolytic affinity was evaluated calculating the contact angle with solutions of NaCl, NaCl-MgSO{sub 4} and Krebs-Ringer. The results show a hydrophilicity increment due to the increase of the surface ruggedness with the synthesis energy. On the contrary, the crystallinity diminishes when increasing the power in PPy and it stays approximately constant in PPy/PEG. The electric conductivity presents a growth from 2 to 4 magnitude orders in function of the water content in the polymers. (Author)

Self-Assembly of Dimeric Tetrathiafulvalene-Calix 4 pyrrole: Receptor for 1,375-Trinitrobenzene

DEFF Research Database (Denmark)

Nielsen, K. A.; Stein, P. C.

2011-01-01

The synthesis and binding properties of a tetrathiafulvalene (TTF)-calix[4]pyrrole receptor 2 appended with one 3,5-dinitrobenzoate guest moiety are reported. The preliminary studies revealed that the receptor is self-compiexing into a dimer receptor 2 center dot 2. The self-complexation of the r......The synthesis and binding properties of a tetrathiafulvalene (TTF)-calix[4]pyrrole receptor 2 appended with one 3,5-dinitrobenzoate guest moiety are reported. The preliminary studies revealed that the receptor is self-compiexing into a dimer receptor 2 center dot 2. The self...

Electroless plating Cu-Co-P polyalloy on UV/ozonolysis irradiated polyethylene terephthalate film and its corrosion resistance

Energy Technology Data Exchange (ETDEWEB)

Hou, Lei; Bi, Siyi; Zhao, Hang; Xu, Yumeng; Mu, Yuhang; Lu, Yinxiang, E-mail: yxlu@fudan.edu.cn

2017-05-01

Highlights: • Electroless plating Cu-Co-P polyalloy was firstly fabricated onto polyethylene terephthalate (PET) substrate. • An etchant-free and amine-free UV/ozonolysis irradiation method UV/ozonolysis was effective for the transition from hydrophilic to hydrophobic of PET sheet. • A time-saving and cost-effective orthogonal experiment (L{sub 9}(3){sup 4}) was utilized to optimize the plating conditions. • The optimized copper polyalloy possessed high corrosion resistance in three aggressive mediums including NaCl, NaOH and HCl, respectively. • The Cu-Co-P coated PET composite showed excellent electromagnetic interference shielding effectiveness (EMI SE > 99.999% at frequency ranging from 30 MHz to 1000 MHz). - Abstract: High corrosion resistant Cu-Co-P coatings were firstly prepared on polyethylene terephthalate (PET) substrate by electroless plating in combination with UV/ozonolysis irradiation under optimized cobalt sulfate heptahydrate concentration, pH value, plating temperature and time. The copper polyalloy/PET composite can be obtained in three steps, namely: (i) the generation of oxygen-containing functionalities (carboxylic groups) onto PET surface through UV irradiation combined with ozone, (ii) Cu seeding catalysts were obtained after being immersed into cupric citrate and NaBH{sub 4} solutions subsequently, and (iii) Cu-Co-P polyalloy metallization using electroless plating bath. Attenuated total reflection fourier transformation infrared spectrometer (ATR-FTIR), X-ray photoelectron spectroscopy (XPS), water contact angle measurement and energy dispersive X-ray analysis (EDAX) were utilized to track the surface changes during the whole process. The electroless plating conditions were optimized by an orthogonal experiment (L{sub 9}(3){sup 4}) for Cu-Co-P coating as follows: CoSO{sub 4}·7H{sub 2}O addition of 0.08 M, pH value, plating temperature and time were set on 10.0, 35 °C and 25 min, respectively. Under the optimal conditions, copper

Visible light carrier generation in co-doped epitaxial titanate films

Energy Technology Data Exchange (ETDEWEB)

Comes, Ryan B.; Smolin, Sergey Y.; Kaspar, Tiffany C.; Gao, Ran; Apgar, Brent A.; Martin, Lane W.; Bowden, Mark E.; Baxter, Jason; Chambers, Scott A.

2015-03-02

Perovskite titanates such as SrTiO3 (STO) exhibit a wide range of important functional properties, including high electron mobility, ferroelectricity—which may be valuable in photovoltaic applications—and excellent photocatalytic performance. The wide optical band gap of titanates limits their use in these applications, however, making them ill-suited for integration into solar energy harvesting technologies. Our recent work has shown that by doping STO with equal concentrations of La and Cr we can enhance visible light absorption in epitaxial thin films while avoiding any compensating defects. In this work, we explore the optical properties of photoexcited carriers in these films. Using spectroscopic ellipsometry, we show that the Cr3+ dopants, which produce electronic states immediately above the top of the O 2p valence band in STO reduce the direct band gap of the material from 3.75 eV to between 2.4 and 2.7 eV depending on doping levels. Transient reflectance measurements confirm that optically generated carriers have a recombination lifetime comparable to that of STO and are in agreement with the observations from ellipsometry. Finally, through photoelectrochemical yield measurements, we show that these co-doped films exhibit enhanced visible light photocatalysis when compared to pure STO.

CO2 laser treatment of As-S chalcogenide thin films

International Nuclear Information System (INIS)

Andriesch, A.M.; Bertolotti, M.; Ferrari, A.; Popesku, A.A.

1990-01-01

The changes of the refractive index of As 2 S 3 and As 2 S 5 films deposited on glass substrates upon CO 2 laser irradiation have been studied. The possibility of writing with the CO 2 laser a waveguiding channel in As 2 S 3 is demonstrated

Design and modelling of enzyme/poly-pyrrole modified electrodes for bio-catalyzed electro-synthesis processes

International Nuclear Information System (INIS)

Gros, Pierre

1996-01-01

This research thesis reports a study which aims at developing, analyzing and integrating an electrode-enzyme interface within an electro-enzymatic reactor to develop electrochemical biosensors. The adopted method comprises a confinement of the enzyme at the electrode surface by means of an electro-formed poly-pyrrole film. The author reports an experimental and theoretical study of the coupling between electrochemical reaction, enzymatic reaction and matter transfer in the polymer in order to better understand the operation of so-modified electrodes. Different parameters have an influence on the reaction rate. A numerical model (validated by experiments) allows the identification of the reaction limiting stages. A new elaboration protocol allows the polymer permeability to be increased. The interface is first applied to the reduction of the NAD coenzyme, and the process is also applied to the production of gluconic acid [fr

Hybrid chitosan–Pluronic F-127 films with BaTiO3:Co nanoparticles: Synthesis and properties

International Nuclear Information System (INIS)

Fuentes, S.; Dubo, J.; Barraza, N.; González, R.; Veloso, E.

2015-01-01

In this study, magnetic BaTiO 3 :Co (BT:Co) nanoparticles prepared using a combined sol–gel–hydrothermal technique were dispersed in a chitosan/Pluronic F-127 solution (QO/Pl) to obtain a nanocomposite hybrid films. Nanoparticles and hybrid films were characterized by X-ray powder diffraction, Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM) and alternating gradient magnetometry (AGM). Experimental results indicated that the BT:Co nanoparticles were encapsulated in the QO/Pl hybrid films and that the magnetic properties of the QO/Pl/BT:Co nanocomposites are similar to the naked BT:Co nanoparticles. Results indicate that Co doping produces an enhancement in the ferromagnetic behavior of the BT nanoparticle. The coating restricts this enhancement only to low-fields, leaving the diamagnetic behavior of BT at high-fields. Magnetically stable sizes (PSD) were obtained at 3% Co doping for both naked nanoparticles and hybrid films. These show an increased magnetic memory capacity and a softer magnetic hardness with respect to non-doped BT nanoparticles. - Highlights: • We described the synthesis of magnetic BaTiO 3 :Co dispersed in chitosan (QO)/Pluronic F-127 (Pl) solution by sonication to obtain nanocomposite hybrid films. • We describe the physical and magnetic properties of BaTiO 3 :Co nanoparticles and QO/Pl/BT:Co hybrid films. • The magnetic properties are defines by the presence of magnetic domains. These magnetic domains are close related with the amount of Co in the host lattice. • The prepared phases could be considered as multifunctional materials, with magnetic and ferri-electrical properties, with potential uses in the design of devices

Epitaxial growth and control of the sodium content in Na{sub x}CoO{sub 2} thin films

Energy Technology Data Exchange (ETDEWEB)

Hildebrandt, Sandra; Komissinskiy, Philipp [Institute for Materials Science, Technische Universität Darmstadt, 64287 Darmstadt (Germany); Major, Marton [Institute for Materials Science, Technische Universität Darmstadt, 64287 Darmstadt (Germany); WIGNER RCP, RMKI, H-1525 Budapest, P.O.B. 49 (Hungary); Donner, Wolfgang [Institute for Materials Science, Technische Universität Darmstadt, 64287 Darmstadt (Germany); Alff, Lambert, E-mail: alff@oxide.tu-darmstadt.de [Institute for Materials Science, Technische Universität Darmstadt, 64287 Darmstadt (Germany)

2013-10-31

Single-phase c-axis oriented Na{sub x}CoO{sub 2} thin films were grown on (001) SrTiO{sub 3} single-crystal substrates, using pulsed laser deposition. X-ray diffraction analysis indicates the epitaxial growth of Na{sub x}CoO{sub 2} thin films in two domains, rotated in-plane by 15 and 45 degrees relative to [100] SrTiO{sub 3}. The sodium stoichiometry x of the films can be controlled in a range of 0.38 < x < 0.84 by in-situ post-deposition annealing the Na{sub x}CoO{sub 2} films at 720 – 760 °C in oxygen for 10 – 30 min. γ - Na{sub x}CoO{sub 2} films are obtained with a full width at half maximum of the (002) Na{sub x}CoO{sub 2} rocking curve below 0.2 degrees. The post-deposition annealing can substitute commonly used chemical deintercalation of Na which is typically associated with a loss in crystallinity. - Highlights: • Single phase Na{sub x}CoO{sub 2} thin films grown by pulsed laser deposition • Epitaxial relations of Na{sub x}CoO{sub 2} thin films on (001) SrTiO{sub 3} substrates • Multi-domain thin films • Control of sodium content by in-situ annealing of Na{sub x}CoO{sub 2} thin films.

Electrografting of in situ generated pyrrole derivative diazonium salt for the surface modification of nickel

International Nuclear Information System (INIS)

Jacques, A.; Devillers, S.; Delhalle, J.; Mekhalif, Z.

2013-01-01

Highlights: • Electrografting of in situ generated 4-pyrrolylphenyldiazonium (Py-PD) on Ni. • Generation of Py-PD from 4-pyrrolylaniline in 3 acidic conditions followed by UV. • XPS and SEM confirm efficiency, reproducibility and homogeneity of the grafting. • Electrografting process assessed by CV. • Barrier properties of the grafted film evidenced by CV. -- Abstract: This work reports for the first time on the modification of nickel surfaces by cathodic electrografting of in situ generated diazonium. An original diazonium salt (the 4-pyrrolylphenyldiazonium called Py-PD hereafter) was electrografted on nickel after its generation from 4-(1H-pyrrol-1-yl)aniline (Py-A) in presence of three acidic conditions (1, 2 and 10 equiv. of HClO 4 /Py-A) has been investigated by UV–vis spectroscopy. Results show that the potentiostatic electrografting of Py-PD is concomitant with nickel and proton reduction. This electrografting leads to the formation of multilayered films in each of the studied in situ generation conditions. The use of 1 equiv. of HClO 4 /Py-A for the in situ generation results in the formation of inhomogeneous and irreproducible coatings while 2 and 10 equiv. lead to the formation of highly covering, homogeneous and reproducible films. These films present good electrochemical barrier properties toward the ferri/ferrocyanide couple. The use of gentle stoichiometric acidic conditions for in situ diazonium generation widens the application field of this one-step procedure to the surface modification of oxidizable materials presenting an unstable oxide layer

Structural Characteristics and Magnetic Properties of Al2O3 Matrix-Based Co-Cermet Nanogranular Films

Directory of Open Access Journals (Sweden)

Giap Van Cuong

2015-01-01

Full Text Available Magnetic micro- and nanogranular materials prepared by different methods have been used widely in studies of magnetooptical response. However, among them there seems to be nothing about magnetic nanogranular thin films prepared by a rf cosputtering technique for both metals and insulators till now. This paper presented and discussed preparation, structural characteristics, and magnetic properties of alumina (Al2O3 matrix-based granular Co-cermet thin films deposited by means of the cosputtering technique for both Co and Al2O3. By varying the ferromagnetic (Co atomic fraction, x, from 0.04 to 0.63, several dominant features of deposition for these thin films were shown. Structural characteristics by X-ray diffraction confirmed a cermet-type structure for these films. Furthermore, magnetic behaviours presented a transition from paramagnetic- to superparamagnetic- and then to ferromagnetic-like properties, indicating agglomeration and growth following Co components of Co clusters or nanoparticles. These results show a typical granular Co-cermet feature for the Co-Al2O3 thin films prepared, in which Co magnetic nanogranules are dispersed in a ceramic matrix. Such nanomaterials can be applied suitably for our investigations in future on the magnetooptical responses of spinplasmonics.

Magnetism of coherent Co and Ni thin films on Cu(111) and Au(111) substrates: An ab initio study

Energy Technology Data Exchange (ETDEWEB)

Zelený, Martin, E-mail: zeleny@fme.vutbr.cz; Dlouhý, Ivo

2017-02-15

We present an ab initio study of structural and magnetic properties of coherent Co and Ni thin films on Cu(111) and Au(111) substrates with thicknesses of up to 6 monolayers. All studied films on Cu(111) substrates prefer structures close their ground state (hcp for Co and fcc for Ni), whereas only the hcp stacking sequence has been found for both films on Au(111) substrates. All studied films exhibit instability of the first monolayer with respect to decomposition into 2-monolayer- or 3-monolayer-high islands, which is in agreement with experimental findings. All studied films are also ferromagnetic, nevertheless the Ni/Cu(111) films reduce their magnetic moments in the layer adjacent to the substrate due to a stronger Cu–Ni interaction at the interface. The magnetic anisotropy of a Co film does not depend on the film thickness: all the studied Co/Au(111) films exhibit a perpendicular magnetic anisotropy, whereas all the Co/Cu(111) films prefer in-plane magnetization. On the other hand, both Ni films change their preference for in-plane orientation of their easy axis to out-of-plane orientation at a critical thickness of 2 monolayers, however, the magnetic anisotropy energies for films thicker than 1 monolayer are smaller than 1 meV/Ni atom. These behaviors of magnetic anisotropy do not depend on the structure of the studied films. - Highlights: • All films exhibit instability of the first monolayer and prefer grow in islands. • The Cu–Ni interaction is responsible for reduced Ni magnetic moments in Ni/Cu(111) films. • The Co/Au(111) and Co/Cu(111) films show different orientations of magnetic anisotropy. • The Ni films exhibit in-plane magnetization only for single monolayer. • Behaviors of magnetic anisotropy do not depend on the structure of the studied films.

Development of p-type amorphous Cu{sub 1−x}B{sub x}O{sub 2−δ} thin films and fabrication of pn hetero junction

Energy Technology Data Exchange (ETDEWEB)

Sanal, K.C., E-mail: sanalcusat@gmail.com [Nanophotonic and Optoelectronic Devices Laboratory, Department of Physics, Cochin University of Science and Technology, Kerala 682022 (India); Inter University Center for Nanomaterials and Devices (IUCND), Cochin University of Science and Technology, Kerala 682022 (India); Center for Advanced Materials, Cochin University of Science and Technology, Kerala 682022 (India); Jayaraj, M.K., E-mail: mkj@cusat.ac.in [Nanophotonic and Optoelectronic Devices Laboratory, Department of Physics, Cochin University of Science and Technology, Kerala 682022 (India); Center for Advanced Materials, Cochin University of Science and Technology, Kerala 682022 (India)

2014-07-01

Highlights: • Growth of p-type semiconducting amorphous Cu{sub 1−x}B{sub x}O{sub 2−δ} thin films by co-sputtering. • Atomic percentage of Cu{sub 1−x}B{sub x}O{sub 2−δ} thin films from the XPS analysis. • Variation of bandgap with boron concentration in Cu{sub 1−x}B{sub x}O{sub 2−δ} thin films. • Demonstration of p–n hetero junctions fabricated in the structure n-Si/p-Cu{sub 1−x}B{sub x}O{sub 2−δ}/Au. - Abstract: Transparent conducting amorphous p type Cu{sub 1−x}B{sub x}O{sub 2−δ} thin films were grown by RF magnetron co-sputtering at room temperature, using copper and boron targets in oxygen atmosphere. The structural, electrical as well as optical properties were studied. Composition of the films was analyzed by XPS. Amorphous structure of as deposited films was confirmed by GXRD. Surface morphology of the films was analyzed by AFM studies. p-Type nature and concentration of carriers were investigated by Hall effect measurement. Band gap of the films was found to increase with the atomic content of boron in the film. A p–n hetero junction using p-type Cu{sub 1−x}B{sub x}O{sub 2−δ} and n-type silicon was fabricated in the structure n-Si/p-Cu{sub 1−x}B{sub x}O{sub 2−δ}/Au which showed rectifying behavior. As deposited amorphous Cu{sub 1−x}B{sub x}O{sub 2−δ} thin films with lower carrier concentration can be used as a channel layer for thin film transistors.

Effects of Interphase Modification and Biaxial Orientation on Dielectric Properties of Poly(ethylene terephthalate)/Poly(vinylidene fluoride-co-hexafluoropropylene) Multilayer Films.

Science.gov (United States)

Yin, Kezhen; Zhou, Zheng; Schuele, Donald E; Wolak, Mason; Zhu, Lei; Baer, Eric

2016-06-01

Recently, poly(vinylidene fluoride) (PVDF)-based multilayer films have demonstrated enhanced dielectric properties, combining high energy density and high dielectric breakdown strength from the component polymers. In this work, further enhanced dielectric properties were achieved through interface/interphase modulation and biaxial orientation for the poly(ethylene terephthalate)/poly(methyl methacrylate)/poly(vinylidene fluoride-co-hexafluoropropylene) [PET/PMMA/P(VDF-HFP)] three-component multilayer films. Because PMMA is miscible with P(VDF-HFP) and compatible with PET, the interfacial adhesion between PET and P(VDF-HFP) layers should be improved. Biaxial stretching of the as-extruded multilayer films induced formation of highly oriented fibrillar crystals in both P(VDF-HFP) and PET, resulting in improved dielectric properties with respect to the unstretched films. First, the parallel orientation of PVDF crystals reduced the dielectric loss from the αc relaxation in α crystals. Second, biaxial stretching constrained the amorphous phase in P(VDF-HFP) and thus the migrational loss from impurity ions was reduced. Third, biaxial stretching induced a significant amount of rigid amorphous phase in PET, further enhancing the breakdown strength of multilayer films. Due to the synergistic effects of improved interfacial adhesion and biaxial orientation, the PET/PMMA/P(VDF-HFP) 65-layer films with 8 vol % PMMA exhibited optimal dielectric properties with an energy density of 17.4 J/cm(3) at breakdown and the lowest dielectric loss. These three-component multilayer films are promising for future high-energy-density film capacitor applications.

Microstructure of Co(112-bar 0) epitaxial thin films, grown on MgO(100) single-crystal substrates

Energy Technology Data Exchange (ETDEWEB)

Nukaga, Yuri; Ohtake, Mitsuru; Futamoto, Masaaki [Faculty of Science and Engineering, Chuo University, 1-13-27 Kasuga, Bunkyo-ku, Tokyo 112-8551 (Japan); Kirino, Fumiyoshi, E-mail: nukaga@futamoto.elect.chuo-u.ac.j [Graduate School of Fine Arts, Tokyo National University of Fine Arts and Music, 12-8 Ueno-koen, Taito-ku, Tokyo 110-8714 (Japan)

2010-01-01

Co(112-bar 0) epitaxial thin films with hcp structure were prepared on MgO(100) single-crystal substrates heated at 300 {sup 0}C by ultra high vacuum molecular beam epitaxy. The microstructure is investigated by employing X-ray diffraction and high-resolution transmission electron microscopy. The film consists of two types of domains whose c-axes are rotated around the film normal by 90{sup 0} each other. Stacking faults are observed for the film along the Co[0001] direction. An atomically sharp boundary is recognized between the film and the substrate, where some misfit dislocations are introduced in the film at the Co/MgO interface. Dislocations are also observed in the film up to 15 nm thickness from the interface. Presence of such stacking faults and misfit dislocations seem to relieve the strain caused by the lattice mismatch between the film and the substrate. X-ray diffraction analysis indicates that the out-of-plane and the in-plane lattice spacings of the film are in agreement within 0.5% and 0.1%, respectively, with those of the bulk hcp-Co crystal, suggesting the strain in the film is very small.

Microstructure of Co(112-bar 0) epitaxial thin films, grown on MgO(100) single-crystal substrates

International Nuclear Information System (INIS)

Nukaga, Yuri; Ohtake, Mitsuru; Futamoto, Masaaki; Kirino, Fumiyoshi

2010-01-01

Co(112-bar 0) epitaxial thin films with hcp structure were prepared on MgO(100) single-crystal substrates heated at 300 0 C by ultra high vacuum molecular beam epitaxy. The microstructure is investigated by employing X-ray diffraction and high-resolution transmission electron microscopy. The film consists of two types of domains whose c-axes are rotated around the film normal by 90 0 each other. Stacking faults are observed for the film along the Co[0001] direction. An atomically sharp boundary is recognized between the film and the substrate, where some misfit dislocations are introduced in the film at the Co/MgO interface. Dislocations are also observed in the film up to 15 nm thickness from the interface. Presence of such stacking faults and misfit dislocations seem to relieve the strain caused by the lattice mismatch between the film and the substrate. X-ray diffraction analysis indicates that the out-of-plane and the in-plane lattice spacings of the film are in agreement within 0.5% and 0.1%, respectively, with those of the bulk hcp-Co crystal, suggesting the strain in the film is very small.

Effect of argon ion etching on the magnetic properties of FeCoB films

Energy Technology Data Exchange (ETDEWEB)

Zhu, Junwei; Zhou, Kan; Yang, Yi; Tang, Dongming; Zhang, Baoshan, E-mail: malab@nju.edu.cn; Lu, Mu; Lu, Huaixian

2015-01-15

In this paper, a new method to modify Ta underlayers by an argon ion etching technology is introduced. Surface roughness of Ta underlayers, as well as soft magnetic properties of post-deposited FeCoB films can be improved by applying a proper ion etching process. The reduction of magnetic coercivity of FeCoB films deposited on the modified Ta underlayers is attributed to the improvement of interfacial roughness, which can reduce magnetic ripples in magnetic films. The microwave damping linewidth of magnetic films is also found to be related to the interfacial roughness. Ta underlayers modified by the ion etching can reduce the influence of two-magnon scattering effect, and thus tune microwave properties of magnetic films. All the results prove that argon ion etching is an effective way to tailor magnetic properties of magnetic films. - Highlights: • We believe that our method to tune the magnetic film properties will be interesting for general readers of Journal of Magnetism and Magnetic Materials. • In the paper, argon ion etching is applied to the Ta underlayer before the FeCoB film is deposited on it. • The modified interface roughness has effectively improved the magnetic properties, including the static magnetic and microwave performance. • The method is valuable for other underlayer/magnetic film systems.

Ibuprofen-loaded poly(lactic-co-glycolic acid films for controlled drug release

Directory of Open Access Journals (Sweden)

Pang JM

2011-04-01

Full Text Available Jianmei Pang1, Yuxia Luan1, Feifei Li1, Xiaoqing Cai1, Jimin Du2, Zhonghao Li31School of Pharmaceutical Science, Shandong University, Jinan, Shandong Province, PR China; 2School of Chemistry and Chemical Engineering, Anyang Normal University, Henan Province, PR China; 3School of Materials Science and Engineering, Shandong University, Jinan, Shandong Province, PR ChinaAbstract: Ibuprofen- (IBU loaded biocompatible poly(lactic-co-glycolic acid (PLGA films were prepared by spreading polymer/ibuprofen solution on the nonsolvent surface. By controlling the weight ratio of drug and polymer, different drug loading polymer films can be obtained. The synthesized ibuprofen-loaded PLGA films were characterized with scanning electron microscopy, powder X-ray diffraction, and differential scanning calorimetry. The drug release behavior of the as-prepared IBU-loaded PLGA films was studied to reveal their potential application in drug delivery systems. The results show the feasibility of the as-obtained films for controlling drug release. Furthermore, the drug release rate of the film could be controlled by the drug loading content and the release medium. The development of a biodegradable ibuprofen system, based on films, should be of great interest in drug delivery systems.Keywords: ibuprofen, controlled release, poly(lactic-co-glycolic acid, films

Interplay between magnetocrystalline anisotropy and exchange bias in epitaxial CoO/Co films

International Nuclear Information System (INIS)

Liu, Hao-Liang; Zeng, Yu-Jia; Van Haesendonck, Chris; Brems, Steven; Temst, Kristiaan; Vantomme, André

2016-01-01

The interplay between magnetocrystalline anisotropy and exchange bias is investigated in CoO/Co bilayer films, which are grown epitaxially on MgO (0 0 1), by magnetization reversal measurements based on the anisotropic magnetoresistance (AMR) effect. While an asymmetric magnetization reversal survives after training for cooling field (CF) along the hard axis, the magnetization reversal becomes symmetric and is dominated in both branches of the hysteresis loop by domain wall motion before and after training for CF along the easy axis. When performing an in-plane hysteresis loop perpendicular to the CF, the hysteresis loop along the easy axis becomes asymmetric: magnetization rotation dominates in the ascending branch, while there is a larger contribution of domain wall motion in the descending branch. Furthermore, the azimuthal angular dependence of the AMR shows two minima after performing a perpendicular hysteresis loop, instead of only one minimum after training. Relying on the extended Fulcomer and Charap model, these effects can be related to an increased deviation of the average uncompensated antiferromagnetic magnetization from the CF direction. This model provides a consistent interpretation of training and asymmetry of the magnetization reversal for epitaxial films with pronounced magnetocrystalline anisotropy as well as for the previously investigated polycrystalline films. (paper)

Ion-beam mixed ultra-thin cobalt suicide (CoSi2) films by cobalt sputtering and rapid thermal annealing

Science.gov (United States)

Kal, S.; Kasko, I.; Ryssel, H.

1995-10-01

The influence of ion-beam mixing on ultra-thin cobalt silicide (CoSi2) formation was investigated by characterizing the ion-beam mixed and unmixed CoSi2 films. A Ge+ ion-implantation through the Co film prior to silicidation causes an interface mixing of the cobalt film with the silicon substrate and results in improved silicide-to-silicon interface roughness. Rapid thermal annealing was used to form Ge+ ion mixed and unmixed thin CoSi2 layer from 10 nm sputter deposited Co film. The silicide films were characterized by secondary neutral mass spectroscopy, x-ray diffraction, tunneling electron microscopy (TEM), Rutherford backscattering, and sheet resistance measurements. The experi-mental results indicate that the final rapid thermal annealing temperature should not exceed 800°C for thin (micrographs of the ion-beam mixed and unmixed CoSi2 films reveals that Ge+ ion mixing (45 keV, 1 × 1015 cm-2) produces homogeneous silicide with smooth silicide-to-silicon interface.

Substrate bias effects on composition and coercivity of CoCrTa/Cr thin films on canasite and glass

Science.gov (United States)

Deng, Y.; Lambeth, D. N.; Sui, X.; Lee, L.-L.; Laughlin, D. E.

1993-05-01

CoCrTa/Cr thin films were prepared by rf diode sputtering onto canasite and glass substrates at various bias voltages from two targets of different compositions (Co82.8Cr14.6Ta2.6 and Co86Cr12Ta2). While Auger depth profile analysis indicates that there is some broadening at the CoCrTa-Cr interface, x-ray fluorescence spectroscopy reveals that changes in alloy composition due to the resputtering processes are even more prominent. For both targets, as the substrate bias increases the Co content in the films declines, and the magnetization decreases. The maximum film coercivity appears to correlate to the final film composition. By investigating the results from both targets, it is concluded that the coercivity reaches a maximum when the film composition is in the neighborhood of Co84Cr13Ta3. Thus, to optimize the coercivity different bias voltages are required for each target. Excessive substrate bias, however, leads to films with low magnetization and coercivity.

Fabrication and characterization of single segment CoNiP and multisegment CoNiP/Au nanowires

International Nuclear Information System (INIS)

Luu Van Thiem; Le Tuan Tu

2014-01-01

This paper presents the fabrication of CoNiP single segment and CoNiP/Au multisegment nanowires. We have fabricated these nanowires by electrodeposition method into polycarbonate templates with a nominal pore diameter about 100 nm. The hysteresis loops were measured with the applied magnetic field parallel and perpendicular to the wire axis using a vibrating sample magnetometer (VSM). The structure morphology was observed by Scanning Electron Microscopy (SEM) and the element composition of CoNiP/Au multisegment nanowires were analyzed by EDS. The results show that nanowires are very uniform with the diameter of 100 nm. The observed coercivity (H C ) and squareness (Mr/Ms) of CoNiP single segment nanowires are larger than the CoNiP/Au multisegment nanowires. (author)

Synthesis of Poly pyrrole Inverse Opal in [bmim] Containing Acetonitrile and the Application of the Inverse Opal in Cell Prototype

International Nuclear Information System (INIS)

Yan, W.; Dong, Q.Q.; Sun, L.N.; Deng, W.; Wu, Sh.

2013-01-01

Most primary cells use Zn or Li as the anode, a metallic oxide as the cathode, and an acidic or alkaline solution or moist past as the electrolytic solution. In this paper, highly ordered poly pyrrole (PPy) inverse opals have been successfully synthesized in the acetonitrile solution containing [bmim]PF 6 . PPy films were prepared under the same experimental conditions. Cyclic voltammograms of the PPy film and the PPy inverse opal in neutral phosphate buffer solution (PBS) were recorded. X-ray photoelectron spectroscopy technique was used to investigate the structural surface of the PPy films and the PPy inverse opals. It is found that the PF 6 - anions kept de doping from the PPy films during the potential scanning process, resulting in the electrochemical inactivity. Although PF 6 - anions also kept de doping from the PPy inverse opals, the PO 4 3- anions from PBS could dope into the inverse opal, explaining why the PPy inverse opals kept their electrochemical activity. An environmental friendly cell prototype was constructed, using the PPy inverse opal as the anode. The electrolytes in both the cathodic and anodic half-cells were neutral PBSs. The open-circuit potential of the cell prototype reached 0.487 V and showed a stable output over several hundred hours

Morphological analysis of co-evaporated blend films based on initial growth for organic photovoltaics

Energy Technology Data Exchange (ETDEWEB)

Shibata, Yosei, E-mail: yosei.shibata@aist.go.jp [Research Center for Photovoltaic Technologies, National Institute of Advanced Industrial Science and Technology, 1-1-1 Higashi, Tsukuba, Ibaraki 305-8565 (Japan); Taima, Tetsuya [Research Center for Photovoltaic Technologies, National Institute of Advanced Industrial Science and Technology, 1-1-1 Higashi, Tsukuba, Ibaraki 305-8565 (Japan); Japan Science and Technology Agency, PRESTO, 4-1-8 Honcho, Kawaguchi, Saitama 332-0012 (Japan); Zhou, Ying; Ohashi, Noboru; Kono, Takahiro [Research Center for Photovoltaic Technologies, National Institute of Advanced Industrial Science and Technology, 1-1-1 Higashi, Tsukuba, Ibaraki 305-8565 (Japan); Yoshida, Yuji, E-mail: yuji.yoshida@aist.go.jp [Research Center for Photovoltaic Technologies, National Institute of Advanced Industrial Science and Technology, 1-1-1 Higashi, Tsukuba, Ibaraki 305-8565 (Japan)

2015-11-15

Graphical abstract: - Highlights: • Initial growth mode of co-evaporated films was observed. • Balanced crystal growth leads to improvement of photovoltaic performance. • Crystal growth of fullerene during co-evaporation process was restricted. • The power conversion efficiency of 3% was obtained without electron blocking layer. - Abstract: Bulk heterojunction structures composed of electron donor and acceptor molecules for application in high-performance organic photovoltaics studied. To fabricate these structures, the co-evaporation method in vacuum is commonly applied; however, the details of the crystal growth process during co-evaporation have not yet been established. Here, we focused on structural analysis of blend films composed of phthalocyanine and fullerene based on initial growth stage. Similar crystal growth behavior to that typically observed in single-component molecules is obtained for the films. These results suggest that the competitive crystal growth between donors and acceptors occurs during co-evaporation process. The balance of thin film growth among donor and acceptor molecules can be related to improved photovoltaic performance. The homogeneous blend structure leads to improvement of the power conversion efficiency from 1.2% to 3.0%.

Investigation of Ni@CoO core-shell nanoparticle films synthesized by sequential layer deposition

Energy Technology Data Exchange (ETDEWEB)

Spadaro, M.C., E-mail: mariachiara.spadaro@unimore.it [CNR-NANO, via G. Campi 213/a, 41125 Modena (Italy); Dipartimento FIM, Università di Modena e Reggio Emilia, via G. Campi 213/a, 41125 Modena (Italy); Luches, P. [Dipartimento FIM, Università di Modena e Reggio Emilia, via G. Campi 213/a, 41125 Modena (Italy); Benedetti, F.; Valeri, S. [CNR-NANO, via G. Campi 213/a, 41125 Modena (Italy); Dipartimento FIM, Università di Modena e Reggio Emilia, via G. Campi 213/a, 41125 Modena (Italy); Turchini, S. [CNR-ISM, Via Fosso del Cavaliere 100, 00133 Roma (Italy); Bertoni, G. [CNR-IMEM, Parco Area delle Scienze 37/a, 43124 Parma (Italy); Ferretti, A.M.; Capetti, E.; Ponti, A. [Laboratorio di Nanotecnologie, Istituto di Scienze e Tecnologie Molecolari, Consiglio Nazionale delle Ricerche, via G. Fantoli 16/15, 20138 Milano (Italy); D’Addato, S. [CNR-NANO, via G. Campi 213/a, 41125 Modena (Italy); Dipartimento FIM, Università di Modena e Reggio Emilia, via G. Campi 213/a, 41125 Modena (Italy)

2017-02-28

Highlights: • We studied Ni/CoO core-shell nanoparticles (NP) obtained with a gas aggregation source. • The NP oxide shells were produced bye reactive deposition of Co in Oxygen atmosphere (p{sub O2} ≈ 10{sup −7} mbar). • XPS, SEM, STEM were used to obtain information on Ni chemical state and NP structure and morphology. • XMCD result showed evidence of remanent magnetization at room temperature. • We interpret XMCD results as due to stabilization induced by exchange bias due to AFM/FM coupling at the core/shell interface. - Abstract: Films of Ni@CoO core-shell nanoparticles (NP Ni core size d ≈ 11 nm) have been grown on Si/SiO{sub x} and lacey carbon supports, by a sequential layer deposition method: a first layer of CoO was evaporated on the substrate, followed by the deposition of a layer of pre-formed, mass-selected Ni NPs, and finally an overlayer of CoO was added. The Ni NPs were formed by a magnetron gas aggregation source, and mass selected with a quadrupole mass filter. The morphology of the films was investigated with Scanning Electron Microscopy and Scanning Transmission Electron Microscopy. The Ni NP cores have a shape compatible with McKay icosahedron, caused by multitwinning occurring during their growth in the source, and the Ni NP layer shows the typical random paving growth mode. After the deposition of the CoO overlayer, CoO islands are observed, gradually extending and tending to merge with each other, with the formation of shells that enclose the Ni NP cores. In situ X-ray Photoelectron Spectroscopy showed that a few Ni atomic layers localized at the core-shell interface are oxidized, hinting at the possibility of creating an intermediate NiO shell between Ni and CoO, depending on the deposition conditions. Finally, X-ray Magnetic Circular Dichroism at the Ni L{sub 2,3} absorption edge showed the presence of magnetization at room temperature even at remanence, revealing the possibility of magnetic stabilization of the NP film.

CoPt/TiN films nanopatterned by RF plasma etching towards dot-patterned magnetic media

Science.gov (United States)

Szívós, János; Pothorszky, Szilárd; Soltys, Jan; Serényi, Miklós; An, Hongyu; Gao, Tenghua; Deák, András; Shi, Ji; Sáfrán, György

2018-03-01

CoPt thin films as possible candidates for Bit Patterned magnetic Media (BPM) were prepared and investigated by electron microscopy techniques and magnetic measurements. The structure and morphology of the Direct Current (DC) sputtered films with N incorporation were revealed in both as-prepared and annealed state. Nanopatterning of the samples was carried out by means of Radio Frequency (RF) plasma etching through a Langmuir-Blodgett film of silica nanospheres that is a fast and high throughput technique. As a result, the samples with hexagonally arranged 100 nm size separated dots of fct-phase CoPt were obtained. The influence of the order of nanopatterning and anneling on the nanostructure formation was revealed. The magnetic properties of the nanopatterned fct CoPt films were investigated by Vibrating Sample Magnetometer (VSM) and Magnetic Force Microscopy (MFM). The results show that CoPt thin film nanopatterned by means of the RF plasma etching technique is promising candidate to a possible realization of BPM. Furthermore, this technique is versatile and suitable for scaling up to technological and industrial applications.

pCO2 And pH regulation of cerebral blood flow

Directory of Open Access Journals (Sweden)

SeongHun eYoon

2012-09-01

Full Text Available CO2 Serves as one of the fundamental regulators of cerebral blood flow. It is widely considered that this regulation occurs through pCO2-driven changes in pH of the cerebral spinal fluid, with elevated and lowered pH causing direct relaxation and contraction of the smooth muscle, respectively. However, some findings also suggest that pCO2 acts independently of and/or in conjunction with altered pH. This action may be due to a direct effect of cerebral spinal fluid pCO2 on the smooth muscle as well as on the endothelium, nerves, and astrocytes. Findings may also point to an action of arterial pCO2 on the endothelium to regulate smooth muscle contractility. Thus, the effects of pH and pCO2 may be influenced by the absence/presence of different cell types in the various experimental preparations. Results may also be influenced by experimental parameters including myogenic tone as well as solutions containing significantly altered HCO3- concentrations, i.e., solutions routinely employed to differentiate the effects of pH from pCO2. In sum, it appears that pCO2, independently and in conjunction with pH, may regulate cerebral blood flow.

Effect of reactive monomer on PS-b-P2VP film.

Science.gov (United States)

Kim, H J; Shin, D M

2014-08-01

Poly(styrene-b-2-vinyl pyridine) (PS-b-P2VP) lamellar film which is hydrophobic block-hydrophilic polyelectrolyte block polymer of 52 kg/mol-b-57 kg/mol and PS-b-P2VP film with reactive monomer (RM257) were prepared for photonic gel films. The lamellar stacks, which is alternating layer of hydrophilic and hydrophobic moiety of PS-b-P2VP, were obtained by exposing the spin coated film under chloroform vapor. The lamellar films were quaternized with 5 wt% of iodomethane diluted by n-hexane. We reported about the influence of reactive monomer on those photonic gel films. Added reactive monomer photonic gel film had higher absorbance than pure photonic gel films. As a result the photonic gel film with RM had more clear color. The lamellar films were swollen by DI water, ethanol (aq) and calcium carbonate solution. The band gaps of the lamellar films were drastically shifted to longer wavelength swollen by calcium carbonate solution. And the lamellar films were shifted to shorter wave length swollen by ethanol. So each lamellar film showed different color.

Nucleation and adhesion of diamond films on Co cemented tungsten carbide

Energy Technology Data Exchange (ETDEWEB)

Polini, R.; Santarelli, M.; Traversa, E.

1999-12-01

Diamond deposits were grown using hot filament chemical vapor deposition (CVD) on pretreated Co cemented tungsten carbide (WC-Co) substrates with an average grain size of 6 {micro}m. Depositions were performed with 0.5 or 1.0% methane concentration and with substrate temperatures ranging from 750 to 1,000 C. Diamond nucleation densities were measured by scanning electron microscopy. Scratched and bias-enhanced nucleation pretreated substrates showed the larger nucleation densities. Etching of the WC performed by Murakami's reagent, followed by surface-Co dissolution (MP pretreatment), led to a roughened but scarcely nucleating surface. The performance of a scratching prior to the MP pretreatment allowed one to increase the nucleation density, due scratching-induced defects, confined in the outermost layer of WC grains, which act as nucleation sites. Smaller nucleation densities were observed with increasing the substrate temperature and reducing the methane concentration, confirming that diamond nucleates via a heterogeneous process. The adhesion of continuous films was evaluated by the reciprocal of the slope of crack radius-indentation load functions. The substrate pretreatments mainly affected the film adhesion, while the influence of CVD process conditions was minor. The two main factors that improve the diamond film adhesion are the coating-substrate contact area and the surface-Co removal.

pH Sensitivity of Novel PANI/PVB/PS3 Composite Films

Directory of Open Access Journals (Sweden)

Olga Korostynska

2007-12-01

Full Text Available This paper reports on the results from the investigation into the pH sensitivity ofnovel PANI/PVB/PS3 composite films. The conductimetric sensing mode was chosen as itis one of the most promising alternatives to the mainstream pH-sensing methods and it is theleast investigated due to the popularity of other approaches. The films were deposited usingboth screen-printing and a drop-coating method. It was found that the best response to pHwas obtained from the screen-printed thick films, which demonstrated a change inconductance by as much as three orders of magnitude over the pH range pH2-pH11. Thedevices exhibited a stable response over 96 hours of operation. Several films were immersedin buffer solutions of different pH values for 96 hours and these were then investigated usingXPS. The resulting N 1s spectra for the various films confirmed that the change inconductance was due to deprotonation of the PANI polymer backbone. SEM andProfilometry were also undertaken and showed that no considerable changes in themorphology of the films took place and that the films did not swell or contract due toexposure to test solutions.

The Microstructures and Electrical Resistivity of (Al, Cr, TiFeCoNiOx High-Entropy Alloy Oxide Thin Films

Directory of Open Access Journals (Sweden)

Chun-Huei Tsau

2015-01-01

Full Text Available The (Al, Cr, TiFeCoNi alloy thin films were deposited by PVD and using the equimolar targets with same compositions from the concept of high-entropy alloys. The thin films became metal oxide films after annealing at vacuum furnace for a period; and the resistivity of these thin films decreased sharply. After optimum annealing treatment, the lowest resistivity of the FeCoNiOx, CrFeCoNiOx, AlFeCoNiOx, and TiFeCoNiOx films was 22, 42, 18, and 35 μΩ-cm, respectively. This value is close to that of most of the metallic alloys. This phenomenon was caused by delaminating of the alloy oxide thin films because the oxidation was from the surfaces of the thin films. The low resistivity of these oxide films was contributed to the nonfully oxidized elements in the bottom layers and also vanishing of the defects during annealing.

Growth and characterization of thin oriented Co{sub 3}O{sub 4} (111) films obtained by decomposition of layered cobaltates Na{sub x}CoO{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Buršík, Josef, E-mail: bursik@iic.cas.cz [Institute of Inorganic Chemistry of the Academy of Sciences of the Czech Republic, v.v.i., 250 68, Husinec-Řež 1001 (Czech Republic); Soroka, Miroslav, E-mail: soroka@iic.cas.cz [Institute of Inorganic Chemistry of the Academy of Sciences of the Czech Republic, v.v.i., 250 68, Husinec-Řež 1001 (Czech Republic); Kužel, Radomír, E-mail: kuzel@karlov.mff.cuni.cz [Faculty of Mathematics and Physics, Charles University in Prague, Ke Karlovu 5, 121 16 Praha 2 (Czech Republic); Mika, Filip, E-mail: filip.mika@isibrno.cz [Institute of Scientific Instruments, Academy of Sciences of the Czech Republic, v.v.i., Královopolská 147, 612 64 Brno (Czech Republic)

2015-07-15

The formation and structural characterization of highly (111)-oriented Co{sub 3}O{sub 4} films prepared by a novel procedure from weakly (001)-oriented Na{sub x}CoO{sub 2} is reported. The Na{sub x}CoO{sub 2} films were deposited on both single crystal and amorphous substrates by chemical solution deposition (CSD) method and crystallized at 700 °C. Subsequently they were transformed into (111)-oriented Co{sub 3}O{sub 4} phase during post-growth annealing at 900 °C. The degree of preferred orientation in Co{sub 3}O{sub 4}, which was determined by phi-scan and pole figure measurements, depends on the content of Na in the starting Na{sub x}CoO{sub 2} phase. Surface morphology of the films was investigated using electron microscopy and atomic force microscopy. - Graphical abstract: Structure of growth twins and possible O{sup 2−} stacking sequences in (111)-oriented Co{sub 3}O{sub 4} thin films on α-Al{sub 2}O{sub 3}(001) prepared by chemical solution deposition through the transformation of (001)-oriented Na{sub x}CoO{sub 2} thin film. - Highlights: • Single phase Co{sub 3}O{sub 4} thin films was prepared by means of chemical solution deposition. • Conditions for γ-Na{sub x}CoO{sub 2} to Co{sub 3}O{sub 4} transformation were optimized. • Growth twinning of Co{sub 3}O{sub 4} films due to two possible O{sup 2−} stacking sequences. • Growth with (pseudo)epitaxial relation Co{sub 3}O{sub 4} (111)[−121]//α-Al{sub 2}O{sub 3} (001)[10−10].

Crystal structures of unsymmetrically mixed β-pyrrole substituted ...

Indian Academy of Sciences (India)

NiTPP(Ph)3(CN)5, 3 complex was synthesized and its solvated structure was examined by crystallography. ... sive interactions among the peripheral substituents.28,29 ... 1H NMR spectra of porphyrins were. 1047 ... Single crystals of MTPP(Ph)3Cl5 (M = 2H and Ni(II)) .... by ∼0.3–0.6ppm but β-pyrrole phenyls do not show.

Asymmetrically substituted calix[4]pyrrole with chiral substituents

Czech Academy of Sciences Publication Activity Database

Štěpánek, P.; Šimák, Ondřej; Nováková, Z.; Wimmer, Zdeněk; Drašar, P.

2011-01-01

Roč. 9, č. 3 (2011), s. 682-683 ISSN 1477-0520 R&D Projects: GA MŠk 2B06024 Grant - others:NATO(XE) CBP.EAP.CLG.982972 Institutional research plan: CEZ:AV0Z40550506; CEZ:AV0Z50380511 Keywords : porphyrin derivatives * anion-binding * aggregation * pyrrole * ketones Subject RIV: CC - Organic Chemistry Impact factor: 3.696, year: 2011

Metallation of N-allenylpyrroles by superbase reagents. Synthesis of new N-substituted pyrroles

International Nuclear Information System (INIS)

Tarasova, O.A.; Brandsma, L.; Verkrajsse, Kh.D.; Mal'kina, A.G.; Trofimov, B.A.

1996-01-01

Metallation of N-allenylpyrrole by BuLi-Et 2 O (THP), BuLi-t-BuOK-THP superbases and reactions of carbanions formed with different electrophilic agents have been studied. Fundamental data on mutual influence of allene group and pyrrole ring have been obtained. Alpha-proton features the highest acidity and it is the first one to be replaced by metal. In BuLi excess (more than 3-fold) in ether or in BuLi-t-BuOK-THP system a through metallation of allene group occurs. New pyrroles functionally substituted in allene chain have been prepared. 19 refs.; 3 tabs

New Method for Fabrication of Co3O4 Thin Film Sensors: Structural, Morphological and Optoelectronic Properties

Directory of Open Access Journals (Sweden)

Vikas PATIL

2011-05-01

Full Text Available Nanocrystalline Co3O4 thin films have been deposited by spin coating technique and then have been analyzed to test their application in NH3 gas-sensing technology. In particular, spectrophotometric and conductivity measurements have been performed in order to determine the optical and electrical properties of Co3O4 thin films. The structure and the morphology of such material have been investigated by X ray diffraction and Scanning electron microscopy. The X-ray diffraction studies confirmed that the films grown by this technique have good crystalline cubic spinel structure and present a random orientation. The morphology of the sol gel derived Co3O4 shows nanocrystalline grains with some overgrown clusters .The optical band gap has been determined from the absorption coefficient. We found that the optical band gap energy decreases from 2.58 eV to 2.07 eV with increasing annealing temperature between 400-700 oC. These mean that the optical quality of Co3O4 films is improved by annealing. The dc electrical conductivity of Co3O4 thin films were increased from 10-4 to 10-2(Ω cm-1 with increase in annealing temperature. The electron carrier concentration (n and mobility (μ of Co3O4 films annealed at 400-700 oC were estimated to be of the order of 2.4 to 4.5 x 1019 cm-3 and 5.2 to 7.0 x 10-5 cm2 V-1 s-1 respectively. It is observed that Co3O4 thin film annealing at 700 oC after deposition provide a smooth and flat texture suited for optoelectronic applications. Gas sensing properties showed that the Co3O4 films (at 700 oC were sensitive as well as fast in responding to NH3. A high sensitivity for ammonia indicates that the Co3O4 films are selective for this gas.

Influence of layer thickness on the structure and the magnetic properties of Co/Pd epitaxial multilayer films

Energy Technology Data Exchange (ETDEWEB)

Tobari, Kousuke, E-mail: tobari@futamoto.elect.chuo-u.ac.jp [Faculty of Science and Engineering, Chuo University, Bunkyo-ku, Tokyo 112-8551 (Japan); Ohtake, Mitsuru; Nagano, Katsumasa; Futamoto, Masaaki [Faculty of Science and Engineering, Chuo University, Bunkyo-ku, Tokyo 112-8551 (Japan)

2012-03-15

Co/Pd epitaxial multilayer films were prepared on Pd(111){sub fcc} underlayers hetero-epitaxially grown on MgO(111){sub B1} single-crystal substrates at room temperature by ultra-high vacuum RF magnetron sputtering. In-situ reflection high energy electron diffraction shows that the in-plane lattice spacing of Co on Pd layer gradually decreases with increasing the Co layer thickness, whereas that of Pd on Co layer remains unchanged during the Pd layer formation. The CoPd alloy phase formation is observed around the Co/Pd interface. The atomic mixing is enhanced for thinner Co and Pd layers in multilayer structure. With decreasing the Co and the Pd layer thicknesses and increasing the repetition number of Co/Pd multilayer film, stronger perpendicular magnetic anisotropy is observed. The relationships between the film structure and the magnetic properties are discussed. - Highlights: Black-Right-Pointing-Pointer Epitaxial Co/Pd multilayer films are prepared on Pd(111){sub fcc} underlayers. Black-Right-Pointing-Pointer Lattice strain in Co layer and CoPd-alloy formation are noted around the interface. Black-Right-Pointing-Pointer Magnetic property dependence on layer thickness is reported.

Gamma irradiation effect on polymers derived of pyrrole synthesized by plasma

International Nuclear Information System (INIS)

Lopez G, O. G.

2013-01-01

This work studies the effect of gamma irradiation at doses of 50, 100, 200, 400 and 800 kGy on polymers obtained from pyrrole synthesized by plasma. The evolution of the structure was studied by Fourier transform infrared spectroscopy (Ftir) and X-ray photoelectron spectroscopy (XPS). The Ftir spectra show that poly pyrroles have N-H, C-H, C=O, triple and consecutive double bonds in their structure. The irradiated polymers show the same chemical groups in their structure without significant changes. Nevertheless, a more detailed analysis by XPS allows the identification of superficial chemical states, such as: C=CH-C, C=CC-C, C-NH-C, C-NC-C, etc., and shows that most of these states are present in all polymers but with different participation. One possible mechanism indicates that as the irradiation dose increases, dehydrogenation processes are performed increasing fragmentation, crosslinking and formation of multiple bonds. The fragmentation and thermal degradation were studied by thermogravimetric analysis, indicating that the loss of moisture and light compounds formed during gamma irradiation occurs in the firsts 100 grades C. The main degradation of all polymers occurs from 150 to 700 grades C, suggesting that the thermal stability is independent of the irradiation dose in the interval studied. Morphology was studied using scanning electron microscopy techniques. Before irradiation, the polymer presented a uniform and practically smooth surface, however, after gamma irradiation, the applied energy increased roughness and macro fragmentation. The roughness and functional groups on the surface reduced the contact angle with water as the irradiation dose increased. However, the polymers are hydrophilic, because for all doses that contact angle is smaller than 90 grades C. Electrical conductivity was calculated respect to temperature in the interval from 25 to 100 grades C. Conductivity increases with temperature and is slightly greater in the irradiated polymers

P-type CuxS thin films: Integration in a thin film transistor structure

International Nuclear Information System (INIS)

Nunes de Carvalho, C.; Parreira, P.; Lavareda, G.; Brogueira, P.; Amaral, A.

2013-01-01

Cu x S thin films, 80 nm thick, are deposited by vacuum thermal evaporation of sulfur-rich powder mixture, Cu 2 S:S (50:50 wt.%) with no intentional heating of the substrate. The process of deposition occurs at very low deposition rates (0.1–0.3 nm/s) to avoid the formation of Cu or S-rich films. The evolution of Cu x S films surface properties (morphology/roughness) under post deposition mild annealing in air at 270 °C and their integration in a thin film transistor (TFT) are the main objectives of this study. Accordingly, Scanning Electron Microscopy studies show Cu x S films with different surface morphologies, depending on the post deposition annealing conditions. For the shortest annealing time, the Cu x S films look to be constructed of grains with large dimension at the surface (approximately 100 nm) and consequently, irregular shape. For the longest annealing time, films with a fine-grained surface are found, with some randomly distributed large particles bound to this fine-grained surface. Atomic Force Microscopy results indicate an increase of the root-mean-square roughness of Cu x S surface with annealing time, from 13.6 up to 37.4 nm, for 255 and 345 s, respectively. The preliminary integration of Cu x S films in a TFT bottom-gate type structure allowed the study of the feasibility and compatibility of this material with the remaining stages of a TFT fabrication as well as the determination of the p-type characteristic of the Cu x S material. - Highlights: • Surface properties of annealed Cu x S films. • Variation of conductivity with annealing temperatures of Cu x S films. • Application of evaporated Cu x S films in a thin film transistor (TFT) structure. • Determination of Cu x S p-type characteristic from TFT behaviour

Interesting reactivity of diketones with pyrrole under acidic condition

Indian Academy of Sciences (India)

e-mail: pkpsc@uohyd.ernet.in; pradeepta.panda@gmail.com. MS received 18 October 2010; revised 7 June 2011; accepted 13 June 2011. Abstract. The acid catalysed condensation of diketones with pyrrole did not result in the formation of expected divergent bisdipyrromethane always; instead the product depends on the ...

Induced anisotropy in amorphous Sm-Co sputtered films

International Nuclear Information System (INIS)

Chen, K.; Hegde, H.; Cadieu, F.J.

1992-01-01

The variation of the in-the-film-plane anisotropy constant, K u , with composition and the magnitude of the field, H s , applied in plane during the sputter deposition of amorphous Sm x Co 1-x , 0.08≤x≤0.40, thin films has been studied. We demonstrate here that with a large H s , 5.0 kOe, a well defined and large in-the-film-plane anisotropy can be obtained. An exceptionally high value of K u =3.3x10 6 erg/cm 3 has been obtained. For the loop measured along the in-plane hard direction, the opening of the loop was undetectable, and the loop along the easy axis was a perfect rectangle. For certain conditions, the anisotropy field measured perpendicular to the film plane when corrected for demagnetization (N d =4π) was the same as that for the in-plane measurements. It is concluded that surface induced short range ordering was the origin of the anisotropy observed in amorphous films deposited in a magnetic field. The formation mechanism is different from that of the short range ordering induced by field annealing

Cycling-induced degradation of LiCoO{sub 2} thin-film cathodes at elevated temperature

Energy Technology Data Exchange (ETDEWEB)

Van Sluytman, J.S.; Alamgir, F.M.; Greenbaum, S.G. [Department of Physics and Astronomy, Hunter College of the City University of New York, 695 Park Avenue, New York, NY 10021 (United States); West, W.C.; Whitacre, J.F. [Electrochemical Technologies Group, Jet Propulsion Laboratory, California Institute of Technology, Pasadena, CA 91109 (United States)

2006-04-01

The cycle life of LiCoO{sub 2}-based all solid-state thin-film cells has been studied at room temperature, and at elevated temperatures of 50, 100, and 150{sup o}C. X-ray diffraction, as well as Raman analysis, has been used to complement the electrochemical data in examining structural and chemical changes. XRD and Raman spectroscopy data indicate that elevated temperature soaks of the thin-film batteries in the quiescent state causes no discernible changes in the LiCoO{sub 2} cathode layer. However, when the thin-film batteries are cycled at elevated temperatures, decreases in average grain size of the LiCoO{sub 2} film occur with dramatic concomitant charge and discharge capacity loss. (author)

Negative thermal expansion and magnetocaloric effect in Mn-Co-Ge-In thin films

Science.gov (United States)

Liu, Y.; Qiao, K. M.; Zuo, S. L.; Zhang, H. R.; Kuang, H.; Wang, J.; Hu, F. X.; Sun, J. R.; Shen, B. G.

2018-01-01

MnCoGe-based alloys with magnetostructural transition show giant negative thermal expansion (NTE) behavior and magnetocaloric effects (MCEs) and thus have attracted a lot of attention. However, the drawback of bad mechanical behavior in these alloys obstructs their practical applications. Here, we report the growth of Mn-Co-Ge-In films with thickness of about 45 nm on (001)-LaAlO3, (001)-SrTiO3, and (001)-Al2O3 substrates. The films grown completely overcome the breakable nature of the alloy and promote its multifunctional applications. The deposited films have a textured structure and retain first-order magnetostructural transition. NTE and MCE behaviors associated with the magnetostructural transition have been studied. The films exhibit a completely repeatable NTE around room temperature. NTE coefficient α can be continuously tuned from the ultra-low expansion (α ˜ -2.0 × 10-7/K) to α ˜ -6.56 × 10-6/K, depending on the growth and particle size of the films on different substrates. Moreover, the films exhibit magnetic entropy changes comparable to the well-known metamagnetic films. All these demonstrate potential multifunctional applications of the present films.

Surface grafting of poly(ethylene glycol) onto poly(acrylamide-co-vinyl amine) cross-linked films under mild conditions.

Science.gov (United States)

Yamamoto, Y; Sefton, M V

1998-01-01

Poly(ethylene glycol) (PEG) was grafted onto poly(acrylamide-co-vinyl amine) (poly(AM-co-VA)) film using tresylated PEG (TPEG) at 37 degrees C in aqueous buffers (pH 7.4) with a view to surface-modifying microencapsulated mammalian cells. Poly(AM-co-VA) film was synthesized by Hofmann degradation of a cross-linked poly(acrylamide) film. Conversion to vinyl amine on the surface of the film was approximately 50%, but bulk conversion was not observed; surface specificity was thought to be the result of cleavage of aminated polymer chains at the surface due to chain scission. Reaction between primary amine and TPEG gave a graft yield of 2 mol% (based on XPS) with respect to available surface amine groups, equivalent to 54 mol% ethylene oxide based on monomer units. Physical adsorption of non-activated polymer was done under identical conditions as a control and the difference in oxygen content was significant compared to TPEG. The type of buffer agent and buffer concentration did not influence graft yields. This graft reaction, which was completed in as little as 2 h was considered to be mild enough to be used for a surface modification of microcapsules containing cells without affecting their viability. Such a surface modification technique may prove to be a useful means of enhancing the biocompatibility of microcapsules (or any tissue engineering construct) even after cell encapsulation or seeding.

Electronic and magnetic properties of TTF and TCNQ covered Co thin films

Energy Technology Data Exchange (ETDEWEB)

Geijn, Elmer van, E-mail: e.vangeijn@utwente.nl; Wang, Kai; Jong, Michel P. de [NanoElectronics Group, MESA+ Institute for Nanotechnology, University of Twente, P.O. Box 217, 7500 AE Enschede (Netherlands)

2016-05-07

Interfacial effects like orbital hybridization and charge transfer strongly influence the transfer of spins from ferromagnetic metals to organic semiconductors and can lead to the formation of interfacial states with distinct magnetic properties. The changes in the electronic and magnetic properties of a thin Co film upon adsorption of a layer of either the molecular organic electron donor tetrathiafulvalene (TTF) or the acceptor tetracyanoquinodimethane (TCNQ) have been investigated by X-ray absorption spectroscopy and X-ray magnetic circular dichroism using synchrotron radiation. Clear differences between the spectra of the adsorbed molecules and the neutral molecules show the hybridization of the molecular orbitals with the Co interface. Deposition of both organic materials leads to a small increase of the ratio of the orbital magnetic moment to the spin magnetic moment of the Co atoms at the interface. The main effect of overlayer deposition is a modification of the magnetic hysteresis of the Co film: The TCNQ slightly reduces the coercivity of the Co, while the TTF increases the coercivity by a factor of ∼1.5. These complementary effects of either a molecular organic electron donor or acceptor on the interfacial properties of a metal ferromagnetic thin film are a promising result for the controlled modification of the magnetic structure of hybrid interfaces.

Magnetic properties and high frequency characteristics of FeCoN thin films

Directory of Open Access Journals (Sweden)

Tae-Jong Hwang

2016-05-01

Full Text Available (Fe65Co35N soft magnetic thin films were prepared by reactive RF magnetron sputtering with the sputtering power of 100 W on thermally oxidized Si substrate in various nitrogen partial pressures (PN2. A strong uniaxial in-plane magnetic anisotropy with the easy-axis coercive field as low as 1∼2 Oe was observed in films grown at PN2 in the range from 3.3% to 5.5%. The saturation magnetizations for those films were about 20 KG. Outside this range, almost isotropic magnetization curves were observed. Vector network analyzer and grounded coplanar waveguide were used to measure the ferromagnetic resonance (FMR signals up to 25 GHz. The FMR signals were detected only in anisotropic films and their FMR frequencies were well fit to the Kittel formula. The obtained g-values and damping parameters at magnetic fields >20 kOe for films grown at PN2 of 3.3%, 4.8% and 5.5% were 1.96, 1.86, 1.92 and 0.0055, 0.0047, 0.0046, respectively. This low damping factor qualifies FeCoN thin films for high-frequency applications.

High-resolution electron microscopy study of Ni81Fe19 film with Co33Cr67 buffer layer

International Nuclear Information System (INIS)

Xu, Q.Y.; Wang, Z.M.; Shen, F.; Du, Y.W.; Zhang, Z.

2003-01-01

The anisotropic magnetoresistance (AMR) in permalloy Ni 81 Fe 19 film deposited on a 1.2 nm Co 33 Cr 67 buffer layer was significantly enhanced. The high-resolution electron microscopy was used to study the microstructure of Ni 81 Fe 19 film with and without Co 33 Cr 67 buffer layer. It was found that Co 33 Cr 67 buffer layer can induce good (1 1 1) texture, while without Co 33 Cr 67 buffer layer, Ni 81 Fe 19 film show randomly oriented grain structure. The Δρ/ρ enhancement is attributed to the decrease in the resistivity ρ of the Ni 81 Fe 19 film due to the formation of the large (1 1 1) textured grains in Ni 81 Fe 19 film with Co 33 Cr 67 buffer layer. However, the surface roughness of substrate may limit the (1 1 1) textured grain size and induce additional grain boundaries in Ni 81 Fe 19 film with Co 33 Cr 67 buffer layer, limit the enhancement of the AMR effect

Room temperature ferromagnetism in Zn{sub 1-x}Co{sub x}S thin films with wurtzite structure

Energy Technology Data Exchange (ETDEWEB)

Patel, Shiv P., E-mail: shivpoojanbhola@gmail.com [Physics Department, University of Allahabad, Allahabad 211002 (India); Pivin, J.C. [CSNSM, IN2P3-CNRS, Batiment 108, F-91405 Orsay Campus (France); Chawla, A.K.; Chandra, Ramesh [Nanoscience Laboratory, IIC, Indian Institute of Technology, Roorkee 247667 (India); Kanjilal, D. [Inter University Accelerator Centre, Aruna Asaf Ali Marg, New Delhi 110067 (India); Kumar, Lokendra, E-mail: lkumarau@gmail.com [Physics Department, University of Allahabad, Allahabad 211002 (India)

2011-11-15

The magnetic properties of Zn{sub 1-x}Co{sub x}S (x=0.025 and 0.05) thin films grown on {alpha}-quartz substrates at different temperatures (T{sub S}) of 200, 400 and 600 deg. C by means of pulsed laser deposition are presented. The films are crystallized with wurtzite structure. Optical absorption and transmission electron microscopy measurements indicate that Co ions are substituted to Zn on tetrahedral sites. Their magnetic response is composed of ferromagnetic and paramagnetic components of which respective strengths depend on T{sub S} and Co concentration. This behavior is interpreted as due to fluctuations in the magnetic ordering, depending on grain size and site location in grain boundaries or in crystal cores. - Highlights: > Co doped ZnS thin films have been fabricated at different substrate temperatures. > Magnetization in the films changes with changing substrate temperature. > Substitution of Co on Zn sites gives room temperature intrinsic ferromagnetism. > Magnetization in the films is composed of ferromagnetic and paramagnetic components.

Composition and structural analysis of Sm-Co thin films on (100)Si

International Nuclear Information System (INIS)

Ghantasala, M.; Sood, D.K.; Mohan, S.

1998-01-01

Full text: The necessity of integration of magnetics with silicon processing technology became essential with the advent of Micro Electromechanical Systems (MEMS). The need to control the crystalline and magnetic properties of the magnetic thin films on silicon substrates has been the primary motivation for this work. The major objective of this work is to prepare the stoichiometric and crystalline SmCo 5 thin films with good magnetic properties on single crystal silicon substrate. We have prepared the SmCo think films on single crystal (100) silicon substrates using DC magnetron sputtering. Films have been prepared in pure argon as the sputter media at two different pressures 2 x 10 -2 torr and 2 x 10 3 torr with the substrates kept at room temperature, 500 and 700 deg C separately. These films have been characterised using RBS, XRD and SEM. RBS analysis showed that the films are nearly stoichiometric (1:4.9) and have significant amounts of oxygen as impurity. But XRD studies indicated that the as deposited films (at all substrate temperatures) are yet to form the crystalline structure. Some of the films have been subjected to rapid thermal annealing at two different temperatures at 800 and 1000 deg C for 30 secs in an effort to crystallise the films. RBS analysis of these films indicated that the room temperature and post annealed films at 1000 deg C resulted in considerable interdiffusion characteristics, whereas the high temperature deposited (500 and 700 deg C) and annealed films showed relatively very stable characteristics with minimal diffusion between the film and the substrate. XRD and SEM analysis of the films is in progress. The detailed results of these investigations will be presented

Phase transformation of the brownmillerite SrCoO{sub 2.5} thin film through alkaline water electrolysis

Energy Technology Data Exchange (ETDEWEB)

Tambunan, Octolia Togibasa; Lee, Min Young; Kim, Deok Hyeon; Parwanta, Kadek Juliana; Jung, Chang Uk [Hankuk University of Foreign Studies, Yongin (Korea, Republic of)

2014-06-15

A phase transformation from insulating brownmillerite SrCoO{sub 2.5} to conducting perovskite SrCoO{sub 3} through electrochemical oxidation has been demonstrated for thin films of SrCoO{sub x} on a SrTiO{sub 3} (001) substrate. The cobalt-oxide film strongly favors the brownmillerite phase of SrCoO{sub 2.5} instead of the perovskite phase of SrCoO{sub 3} on a SrTiO{sub 3} (001) substrate due to its low lattice mismatch. Therefore, the phase transformation has its own retention. The alkaline water electrolysis occurs between the copper cathode and the SrCoO{sub 2.5} film anode. The H{sup +} ions are attracted to the cathode and generate H{sub 2} gas. The OH{sup -} ions are attracted to the film's surface and generate a rich amount of oxygen to fill the oxygen vacancy channel of brownmillerite SrCoO{sub 2.5}. The phase transformation was verified from the change in the out-of-plane lattice constant and the change in the resistivity of the electrolyzed film.

Synthesis and characterization of silver-polypyrrole film composite

Energy Technology Data Exchange (ETDEWEB)

Ayad, Mohamad M., E-mail: mayad12000@yahoo.com [Department of Chemistry, Faculty of Science, University of Tanta, Tanta (Egypt); Zaki, Eman [Department of Chemistry, Faculty of Science, University of Tanta, Tanta (Egypt)

2009-11-15

In this work, we report the chemical polymerization of pyrrole to obtain thin film of polypyrrole (PPy) hydrochloride deposited onto the electrode of the quartz crystal microbalance (QCM). The film in the base form was exposed to a solution of AgNO{sub 3}. Electroless reduction for silver ions by the PPy film took place and silver particles were adsorbed onto the film surface. The silver particles content at the PPy films were analyzed by QCM and the results showed that the concentrations of silver uptakes increase as the original AgNO{sub 3} solution increases. The morphology of the surface of the PPy film and the silver-PPy film composite were studied by the scanning electron microscopy (SEM) coupled with energy dispersive X-ray spectrometry (EDX). They showed that the obtained silver particles have spherical, cubic and tetrahedral structures. X-ray diffraction (XRD) and Fourier transformed infra-red spectroscopy (FTIR) were used to characterize the structure of the powder composite. This work reveals the capability of PPy film coating on QCM in sensing and removing silver from several environmental samples.

Synthesis and characterization of silver-polypyrrole film composite

International Nuclear Information System (INIS)

Ayad, Mohamad M.; Zaki, Eman

2009-01-01

In this work, we report the chemical polymerization of pyrrole to obtain thin film of polypyrrole (PPy) hydrochloride deposited onto the electrode of the quartz crystal microbalance (QCM). The film in the base form was exposed to a solution of AgNO 3 . Electroless reduction for silver ions by the PPy film took place and silver particles were adsorbed onto the film surface. The silver particles content at the PPy films were analyzed by QCM and the results showed that the concentrations of silver uptakes increase as the original AgNO 3 solution increases. The morphology of the surface of the PPy film and the silver-PPy film composite were studied by the scanning electron microscopy (SEM) coupled with energy dispersive X-ray spectrometry (EDX). They showed that the obtained silver particles have spherical, cubic and tetrahedral structures. X-ray diffraction (XRD) and Fourier transformed infra-red spectroscopy (FTIR) were used to characterize the structure of the powder composite. This work reveals the capability of PPy film coating on QCM in sensing and removing silver from several environmental samples.

Synthesis and characterization of silver-polypyrrole film composite

Science.gov (United States)

Ayad, Mohamad. M.; Zaki, Eman

2009-11-01

In this work, we report the chemical polymerization of pyrrole to obtain thin film of polypyrrole (PPy) hydrochloride deposited onto the electrode of the quartz crystal microbalance (QCM). The film in the base form was exposed to a solution of AgNO 3. Electroless reduction for silver ions by the PPy film took place and silver particles were adsorbed onto the film surface. The silver particles content at the PPy films were analyzed by QCM and the results showed that the concentrations of silver uptakes increase as the original AgNO 3 solution increases. The morphology of the surface of the PPy film and the silver-PPy film composite were studied by the scanning electron microscopy (SEM) coupled with energy dispersive X-ray spectrometry (EDX). They showed that the obtained silver particles have spherical, cubic and tetrahedral structures. X-ray diffraction (XRD) and Fourier transformed infra-red spectroscopy (FTIR) were used to characterize the structure of the powder composite. This work reveals the capability of PPy film coating on QCM in sensing and removing silver from several environmental samples.

Hybrid chitosan–Pluronic F-127 films with BaTiO{sub 3}:Co nanoparticles: Synthesis and properties

Energy Technology Data Exchange (ETDEWEB)

Fuentes, S., E-mail: sfuentes@ucn.cl [Departamento de Ciencias Farmacéuticas, Facultad de Ciencias, Universidad Católica del Norte, Casilla 1280, Antofagasta (Chile); Center for the Development of Nanoscience and Nanotechnology, CEDENNA, Santiago (Chile); Dubo, J. [Departamento de Ciencias Farmacéuticas, Facultad de Ciencias, Universidad Católica del Norte, Casilla 1280, Antofagasta (Chile); Barraza, N. [Departamento de Física, Facultad de Ciencias, Universidad Católica del Norte, Casilla 1280, Antofagasta (Chile); González, R. [Laboratorio de Magnetismo, Departamento de Ciencias Geológicas, Universidad Católica del Norte, Antofagasta (Chile); Veloso, E. [Dirección de Investigaciones Científicas y Tecnológicas, Pontificia Universidad Católica de Chile, Avenida Vicuña Mackenna 4860, Santiago (Chile)

2015-03-01

In this study, magnetic BaTiO{sub 3}:Co (BT:Co) nanoparticles prepared using a combined sol–gel–hydrothermal technique were dispersed in a chitosan/Pluronic F-127 solution (QO/Pl) to obtain a nanocomposite hybrid films. Nanoparticles and hybrid films were characterized by X-ray powder diffraction, Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM) and alternating gradient magnetometry (AGM). Experimental results indicated that the BT:Co nanoparticles were encapsulated in the QO/Pl hybrid films and that the magnetic properties of the QO/Pl/BT:Co nanocomposites are similar to the naked BT:Co nanoparticles. Results indicate that Co doping produces an enhancement in the ferromagnetic behavior of the BT nanoparticle. The coating restricts this enhancement only to low-fields, leaving the diamagnetic behavior of BT at high-fields. Magnetically stable sizes (PSD) were obtained at 3% Co doping for both naked nanoparticles and hybrid films. These show an increased magnetic memory capacity and a softer magnetic hardness with respect to non-doped BT nanoparticles. - Highlights: • We described the synthesis of magnetic BaTiO{sub 3}:Co dispersed in chitosan (QO)/Pluronic F-127 (Pl) solution by sonication to obtain nanocomposite hybrid films. • We describe the physical and magnetic properties of BaTiO{sub 3}:Co nanoparticles and QO/Pl/BT:Co hybrid films. • The magnetic properties are defines by the presence of magnetic domains. These magnetic domains are close related with the amount of Co in the host lattice. • The prepared phases could be considered as multifunctional materials, with magnetic and ferri-electrical properties, with potential uses in the design of devices.

Effects of substrate temperature and Cu underlayer thickness on the formation of SmCo5(0001) epitaxial thin films

International Nuclear Information System (INIS)

Ohtake, Mitsuru; Nukaga, Yuri; Futamoto, Masaaki; Kirino, Fumiyoshi

2010-01-01

SmCo 5 (0001) epitaxial thin films were prepared on Cu(111) underlayers heteroepitaxially grown on Al 2 O 3 (0001) single-crystal substrates by molecular beam epitaxy. The effects of substrate temperature and Cu underlayer thickness on the crystallographic properties of SmCo 5 (0001) epitaxial films were investigated. The Cu atoms of underlayer diffuse into the SmCo 5 film and substitute the Co sites in SmCo 5 structure forming an alloy compound of Sm(Co,Cu) 5 . The ordered phase formation is enhanced with increasing the substrate temperature and with increasing the Cu underlayer thickness. The Cu atom diffusion into the SmCo 5 film is assisting the formation of Sm(Co,Cu) 5 ordered phase.

Layered Ni(OH)2-Co(OH)2 films prepared by electrodeposition as charge storage electrodes for hybrid supercapacitors.

Science.gov (United States)

Nguyen, Tuyen; Boudard, Michel; Carmezim, M João; Montemor, M Fátima

2017-01-04

Consecutive layers of Ni(OH) 2 and Co(OH) 2 were electrodeposited on stainless steel current collectors for preparing charge storage electrodes of high specific capacity with potential application in hybrid supercapacitors. Different electrodes were prepared consisting on films of Ni(OH) 2 , Co(OH) 2 , Ni 1/2 Co 1/2 (OH) 2 and layered films of Ni(OH) 2 on Co(OH) 2 and Co(OH) 2 on Ni(OH) 2 to highlight the advantages of the new architecture. The microscopy studies revealed the formation of nanosheets in the Co(OH) 2 films and of particles agglomerates in the Ni(OH) 2 films. Important morphological changes were observed in the double hydroxides films and layered films. Film growth by electrodeposition was governed by instantaneous nucleation mechanism. The new architecture composed of Ni(OH) 2 on Co(OH) 2 displayed a redox response characterized by the presence of two peaks in the cyclic voltammograms, arising from redox reactions of the metallic species present in the layered film. These electrodes revealed a specific capacity of 762 C g -1 at the specific current of 1 A g -1 . The hybrid cell using Ni(OH) 2 on Co(OH) 2 as positive electrode and carbon nanofoam paper as negative electrode display specific energies of 101.3 W h g -1 and 37.8 W h g -1 at specific powers of 0.2 W g -1 and 2.45 W g -1 , respectively.

Structural and magnetic characterization of mixed valence Co(II, III)xZn1−xO epitaxial thin films

International Nuclear Information System (INIS)

Negi, D.S.; Loukya, B.; Dileep, K.; Sahu, R.; Shetty, S.; Kumar, N.; Ghatak, J.; Pachauri, N.; Gupta, A.; Datta, R.

2014-01-01

In this article, we report on the Co atom incorporation, secondary phase formation and composition-dependent magnetic and optical properties of mixed valence Co(II, III) x Zn 1−x O epitaxial thin films grown by pulsed laser deposition. The intended total Co concentration is varied between ∼6–60 at.% with relatively higher concentration of +3 over +2 charge state. Mixed valence Co(II, III) shows high solubility in ZnO (up to 38 at.%) and ferromagnetism is observed in samples with total Co incorporation of ∼29 and 38 at.%. Electron diffraction pattern and high resolution transmission electron microscopy images reveal single crystalline nature of the thin films with wurtzite structure. Co oxide interlayer, with both rock salt and spinel structure, are observed to be formed between the substrate and wurtzite film for total Co concentration at ∼17 at.% and above. Magnetization shows composition dependence with a saturation moment value of ∼93 emu cm −3 and a coercive field of ∼285 Oe observed for ∼38 at.% Co:ZnO films. Ferromagnetism was not observed for films with Co concentration 17 and 9 at.%. The Co oxide interlayer does not show any ferromagnetism. All the films are n-type with carrier concentration ∼10 19 cm −3 . The observed magnetism is probably resulting from direct antiferromagntic exchange interaction between Co 2+ and Co 3+ ions favored by heavy Co alloying giving rise to ferrimagnetism in the system. - Highlights: • Mixed valence Co doped ZnO ferromagnetic single crystal thin film. • Secondary phase formation in terms of CoO and Co3O4 and magnetism is observed only for high Co alloying. • Cathodoluminescence (CL) data showing increase in band gap with Co concentrations

Catalytic formal [2+2+1] synthesis of pyrroles from alkynes and diazenes via Ti(II)/Ti(IV) redox catalysis.

Science.gov (United States)

Gilbert, Zachary W; Hue, Ryan J; Tonks, Ian A

2016-01-01

Pyrroles are structurally important heterocycles. However, the synthesis of polysubstituted pyrroles is often challenging. Here, we report a multicomponent, Ti-catalysed formal [2+2+1] reaction of alkynes and diazenes for the oxidative synthesis of penta- and trisubstituted pyrroles: a nitrenoid analogue to classical Pauson-Khand-type syntheses of cyclopentenones. Given the scarcity of early transition-metal redox catalysis, preliminary mechanistic studies are presented. Initial stoichiometric and kinetic studies indicate that the mechanism of this reaction proceeds through a formally Ti(II)/Ti(IV) redox catalytic cycle, in which an azatitanacyclobutene intermediate, resulting from [2+2] alkyne + Ti imido coupling, undergoes a second alkyne insertion followed by reductive elimination to yield pyrrole and a Ti(II) species. The key component for catalytic turnover is the reoxidation of the Ti(II) species to a Ti(IV) imido via the disproportionation of an η(2)-diazene-Ti(II) complex.

Structural, optical and magnetic properties of nanocrystalline Co-doped ZnO thin films grown by sol-gel

Energy Technology Data Exchange (ETDEWEB)

Kayani, Zohra Nazir; Shah, Iqra; Zulfiqar, Bareera; Sabah, Aneeqa [Lahore College for Women Univ., Lahore (Pakistan); Riaz, Saira; Naseem, Shahzad [Univ. of the Punjab, Lahore (Pakistan). Centre of Excellence in Solid State Physics

2018-04-01

Cobalt-doped ZnO thin films have been deposited using a sol-gel route by changing the number of coats on the substrate from 6 to 18. This project deals with various film thicknesses by increasing the number of deposited coats. The effect of thickness on structural, magnetic, surface morphology and optical properties of Co-doped ZnO thin film was studied. The crystal structure of the Co-doped ZnO films was investigated by X-ray diffraction. The films have polycrystalline wurtzite hexagonal structures. A Co{sup 2+} ion takes the place of a Zn{sup 2+} ion in the lattice without creating any distortion in its hexagonal wurtzite structure. An examination of the optical transmission spectra showed that the energy band gap of the Co-doped ZnO films increased from 3.87 to 3.97 eV with an increase in the number of coatings on the substrate. Ferromagnetic behaviour was confirmed by measurements using a vibrating sample magnetometer. The surface morphology of thin films was assessed by scanning electron microscope. The grain size on the surface of thin films increased with an increase in the number of coats.

TiFeCoNi oxide thin film - A new composition with extremely low electrical resistivity at room temperature

International Nuclear Information System (INIS)

Yang, Ya-Chu; Tsau, Chun-Huei; Yeh, Jien-Wei

2011-01-01

We show the electrical resistivity of a TiFeCoNi oxide thin film. The electrical resistivity of the TiFeCoNi thin film decreased sharply after a suitable period of oxidation at high temperature. The lowest resistivity of the TiFeCoNi oxide film was 35 ± 3 μΩ-cm. The low electrical resistivity of the TiFeCoNi oxide thin film was attributed to Ti, which is more reactive than the other elements, reacting with oxygen at the initial stage of annealing. The low resistivity is caused by the remaining electrons.

A comparative study of Co thin film deposited on GaAs (1 0 0) and glass substrates

International Nuclear Information System (INIS)

Sharma, A.; Brajpuriya, R.; Tripathi, S.; Jain, D.; Dubey, R.; Shripathi, T.; Chaudhari, S.M.

2006-01-01

The structural, magnetic and transport properties of Co/GaAs (1 0 0) and Co/glass thin films have been investigated. The structural measurements reveal the crystalline nature of Co thin film grown on GaAs, while microcrystalline nature in case of glass substrate. The film grown on GaAs shows higher coercivity (49.0 G), lower saturation magnetization (3.65 x 10 -4 ) and resistivity (8 μΩ cm) values as compared to that on glass substrate (22 G, 4.77 x 10 -4 and 18 μΩ cm). The grazing incidence X-ray reflectivity and photoemission spectroscopy results show the interaction between Co and GaAs at the interface, while the Co layer grown on glass remains unaffected. These observed results are discussed and interpreted in terms of different growth morphologies and structures of as grown Co thin film on both substrates

Efficient assembly of polysubstituted pyrroles via a (3 + 2) cycloaddition/skeletal rearrangement/redox isomerization cascade reaction.

Science.gov (United States)

Yu, Yuanyuan; Wang, Chunyu; He, Xinze; Yao, Xiaotong; Zu, Liansuo

2014-07-03

An unprecedented cascade strategy, used in conjunction with a redox isomerization, for the synthesis of 3-allyl pyrroles is reported. In a single step, readily accessible simple starting materials are transformed into highly substituted pyrroles with high efficiency. The products obtained contain allyl substituents, which can be readily elaborated to other useful functional groups. The reaction proceeds through an unusual (3 + 2) cycloaddition/skeletal rearrangement/redox isomerization pathway.

Thermal oxidation of Ni films for p-type thin-film transistors

KAUST Repository

Jiang, Jie; Wang, Xinghui; Zhang, Qing; Li, Jingqi; Zhang, Xixiang

2013-01-01

p-Type nanocrystal NiO-based thin-film transistors (TFTs) are fabricated by simply oxidizing thin Ni films at temperatures as low as 400 °C. The highest field-effect mobility in a linear region and the current on-off ratio are found to be 5.2 cm2 V-1 s-1 and 2.2 × 103, respectively. X-ray diffraction, transmission electron microscopy and electrical performances of the TFTs with "top contact" and "bottom contact" channels suggest that the upper parts of the Ni films are clearly oxidized. In contrast, the lower parts in contact with the gate dielectric are partially oxidized to form a quasi-discontinuous Ni layer, which does not fully shield the gate electric field, but still conduct the source and drain current. This simple method for producing p-type TFTs may be promising for the next-generation oxide-based electronic applications. © 2013 the Owner Societies.

Antidot patterned single and bilayer thin films based on ferrimagnetic Tb-Co alloy with perpendicular magnetic anisotropy

Science.gov (United States)

Kulesh, N. A.; Vázquez, M.; Lepalovskij, V. N.; Vas'kovskiy, V. O.

2018-02-01

Hysteresis properties and magnetization reversal in TbCo(30 nm) and FeNi(10 nm)/TbCo(30 nm) films with nanoscale antidot lattices are investigated to test the effect of nanoholes on the perpendicular anisotropy in the TbCo layer and the induced exchange bias in the FeNi layer. The antidots are introduced by depositing the films on top of hexagonally ordered porous anodic alumina substrates with pore diameter and interpore distance fixed to 75 nm and 105 nm, respectively. The analysis of combined vibrating sample magnetometry, Kerr microscopy and magnetic force microscopy imaging measurements has allowed us to link macroscopic and local magnetization reversal processes. For magnetically hard TbCo films, we demonstrate the tunability of magnetic anisotropy and coercive field (i.e., it increases from 0.2 T for the continuous film to 0.5 T for the antidot film). For the antidot FeNi/TbCo film, magnetization of FeNi is confirmed to be in plane. Although an exchange bias has been locally detected in the FeNi layer, the integrated hysteresis loop has increased coercivity and zero shift along the field axis due to the significantly decreased magnetic anisotropy of TbCo layer.

Triazine containing N-rich microporous organic polymers for CO{sub 2} capture and unprecedented CO{sub 2}/N{sub 2} selectivity

Energy Technology Data Exchange (ETDEWEB)

Bhunia, Subhajit; Bhanja, Piyali; Das, Sabuj Kanti [Department of Material Science, Indian Association for the Cultivation of Science, Jadavpur, Kolkata 700032 (India); Sen, Tapas [Nanobiomaterials Research Group, Centre for Materials Science, School of Physical Sciences and Computing, University of Central Lancashire, Preston PR1 2HE (United Kingdom); Bhaumik, Asim, E-mail: msab@iacs.res.in [Department of Material Science, Indian Association for the Cultivation of Science, Jadavpur, Kolkata 700032 (India)

2017-03-15

Targeted synthesis of microporous adsorbents for CO{sub 2} capture and storage is very challenging in the context of remediation from green house gases. Herein we report two novel N-rich microporous networks SB-TRZ-CRZ and SB-TRZ-TPA by extensive incorporation of triazine containing tripodal moiety in the porous polymer framework. These materials showed excellent CO{sub 2} storage capacities: SB-TRZ-CRZ displayed the CO{sub 2} uptake capacity of 25.5 wt% upto 1 bar at 273 K and SB-TRZ-TPA gave that of 16 wt% under identical conditions. The substantial dipole quadruple interaction between network (polar triazine) and CO{sub 2} boosts the selectivity for CO{sub 2}/N{sub 2}. SB-TRZ-CRZ has this CO{sub 2}/N{sub 2} selectivity ratio of 377, whereas for SB-TRZ-TPA it was 97. Compared to other porous polymers, these materials are very cost effective, scalable and very promising material for clean energy application and environmental issues. - Graphical abstract: We report two novel N-rich microporous polymeric materials by doping of triazine containing tripodal dopant in the organic framework. These materials showed excellent CO{sub 2} storage capacities as high as 25.5 wt% under 1 bar pressure with exceptional CO{sub 2}/N{sub 2} selectivity of 377. - Highlights: • Triazine containing trimodal moiety incorporated in polycarbazolic and poly triphenylamine networks. • N-rich crosslinked polymers with high BET surface area and 1.5–1.7 nm size large micropores. • CO{sub 2} uptake capacity of 25.5 wt% upto 1 bar at 273 K. • These crosslinked porous polymers showed exceptional CO{sub 2}/N{sub 2} selectivity.

Coupling of microphase separation and dewetting in weakly segregated diblock co-polymer ultrathin films.

Science.gov (United States)

Yan, Derong; Huang, Haiying; He, Tianbai; Zhang, Fajun

2011-10-04

We have studied the coupling behavior of microphase separation and autophobic dewetting in weakly segregated poly(ε-caprolactone)-block-poly(L-lactide) (PCL-b-PLLA) diblock co-polymer ultrathin films on carbon-coated mica substrates. At temperatures higher than the melting point of the PLLA block, the co-polymer forms a lamellar structure in bulk with a long period of L ∼ 20 nm, as determined using small-angle X-ray scattering. The relaxation procedure of ultrathin films with an initial film thickness of h = 10 nm during annealing has been followed by atomic force microscopy (AFM). In the experimental temperature range (100-140 °C), the co-polymer dewets to an ultrathin film of itself at about 5 nm because of the strong attraction of both blocks with the substrate. Moreover, the dewetting velocity increases with decreasing annealing temperatures. This novel dewetting kinetics can be explained by a competition effect of the composition fluctuation driven by the microphase separation with the dominated dewetting process during the early stage of the annealing process. While dewetting dominates the relaxation procedure and leads to the rupture of the ultrathin films, the composition fluctuation induced by the microphase separation attempts to stabilize them because of the matching of h to the long period (h ∼ 1/2L). The temperature dependence of these two processes leads to this novel relaxation kinetics of co-polymer thin films. © 2011 American Chemical Society

Defect mediated reversible ferromagnetism in Co and Mn doped zinc oxide epitaxial films

Energy Technology Data Exchange (ETDEWEB)

Mal, Siddhartha; Nori, Sudhakar; Narayan, J. [Department of Material Science and Engineering, North Carolina State University, Raleigh, North Carolina 27695 (United States); Mula, Suhrit [Department of Material Science and Engineering, North Carolina State University, Raleigh, North Carolina 27695 (United States); Department of Metallurgical and Materials Engineering, National Institute of Technology, Rourkela 769008 (India); Prater, J. T. [Materials Science Division, Army Research Office, Research Triangle Park, North Carolina 27709 (United States)

2012-12-01

We have introduced defects in ZnO (undoped and doped with Co and Mn) epitaxial thin films using laser irradiation from nanosecond laser pulses and thermal annealing in oxygen ambient. In contrast to the as grown samples, the laser irradiated films show a significant increase in conductivity, enhancement in UV emission, while maintaining the same wurtzite crystal structure. Room-temperature ferromagnetism (RTFM) is observed in laser-irradiated samples, which increased with the number of laser pulses up to a certain value where magnetic moment saturates. The induced ferromagnetism as well as the enhanced electrical conductivity can be reversed with thermal annealing in oxygen ambient. The magnetization in Co and Mn doped films was found to be strong function of growth conditions and defect concentration. X-ray diffraction and optical absorption experiments suggested a 2+ valance state and tetrahedral coordination for both Co and Mn ions. There is a simultaneous increase in n-type electrical conductivity with the number of laser pulses and continue to exhibit semiconducting behavior in both undoped and doped films. The saturation magnetization was found to be 0.08 {mu}{sub B}/Co and 0.05 {mu}{sub B}/Mn, much lower than 3.0 {mu}{sub B}/Co and 5.0 {mu}{sub B}/Mn, indicating the prominent role of intrinsic defects in RTFM with some contribution from Co{sup 2+}-oxygen vacancy complexes. We propose a unified mechanism based upon introduction of intrinsic defects to explain RTFM and n-type conductivity enhancements during pulsed laser and thermal annealing.

Pr and Gd co-doped bismuth ferrite thin films with enhanced ...

Indian Academy of Sciences (India)

in Pr content, the crystal structures of BPGFO thin films retain rhombohedral (R3c) symmetry accompanied by structure distortion. ... Pr and Gd co-modified BiFeO3 thin film; ferroelectric properties; sol-gel. 1. Introduction. In recent years, great attention has been paid to single- phase BiFeO3 (BFO) multiferroic materials ...

Inkjet Printing as High-Throughput Technique for the Fabrication of NiCo2O4 Films

Directory of Open Access Journals (Sweden)

Reyna Dianela Bacelis-Martínez

2017-01-01

Full Text Available Owing to its distinctive physicochemical properties, nickel-cobalt mixed oxide (NiCo2O4 has become a promising and innovative material for applications in many technological fields. The design of fast and reliable techniques for the deposition of this material is essential in the development of applications. In this work, NiCo2O4 films were successfully prepared by an inkjet printing technique using a suitable ink obtained from metal nitrates in a glycerol-water mixture. In order to deposit well-defined and uniform film patterns, the instrumental parameters such as drop spacing and inkjet voltage have been explored. The pure crystalline bimetallic nickel cobaltite oxide is obtained at 500°C with a homogeneous compositional distribution along the film. The average thickness observed by scanning electron microscopy is around 490 nm, whereas X-ray photoelectron spectroscopy analysis revealed that the film surface presents mixed oxidation states for both metals: Co2+, Co3+, Ni2+, and Ni3+. The electrocatalytic performance of inkjet-printed NiCo2O4 films for the water oxidation reaction is comparable with earlier reports.

Magnetic and other properties and sputtering behavior of Co-base amorphous alloy films

International Nuclear Information System (INIS)

Hayashi, K.; Hayakawa, M.; Ochiai, Y.; Matsuda, H.; Ishikawa, W.; Iwasaki, Y.; Aso, K.

1987-01-01

Magnetic and other properties of Co-base amorphous alloy films prepared by sputtering are investigated. A detailed magnetic phase diagram with saturation magnetic flux density, crystallization temperature, and zero-magnetostrictive line on Co-Ta-Zr amorphous alloys were obtained, and the technical knowhow to make a film with well-reproducible characteristics by widely changing the sputtering conditions was related with these physical properties. Especially on alloy sputtering, a phenomenological model for elucidating a composition difference between film and target is presented. After these studies, the film characteristics of B/sub s/ = 12 kG, T/sub x/ = 450 0 C, chemical bondλ/sub s/chemical bond -8 , H/sub c/<10 mOe, and permeabilities of μ(1 MHz) = 7000, μ(100 MHz) = 2000 for the single film of 2 μm in thickness and of μ(1 MHz) = 4000, μ(100 MHz) = 800 for the insulator-sandwiched multilayered film of 10 μm are obtained, and these well-balanced values enable us to apply the materials for high-frequency recording head

Soft magnetic properties and damping parameter of (FeCo-Al alloy thin films

Directory of Open Access Journals (Sweden)

Isao Kanada

2017-05-01

Full Text Available For high frequency device applications, a systematic study of the soft magnetic properties and magnetization dynamics of (FeCo-Al alloy thin films has been carried out. A low effective damping parameter αeff of 0.002 and a high saturation magnetization of about 1,800 emu/cc are obtained at y=0.2∼0.3 for (Fe1-yCoy98Al2 alloy thin films deposited onto fused silica and MgO(100 at an ambient temperature during deposition. Those films are of the bcc structure with the orientation normal to the film plane. They possess a columnar structure, grown along the film normal. The column width is found to be about 20 nm for y=0.25. It is concluded that the (FeCo-Al thin films with a damping parameter as low as 0.002 and high saturation magnetization of about 1,800 emu/cc have been successfully fabricated, and that they are potential for future high frequency device applications.

Intrinsic and spatially nonuniform ferromagnetism in Co-doped ZnO films

Science.gov (United States)

Tseng, L. T.; Suter, A.; Wang, Y. R.; Xiang, F. X.; Bian, P.; Ding, X.; Tseng, A.; Hu, H. L.; Fan, H. M.; Zheng, R. K.; Wang, X. L.; Salman, Z.; Prokscha, T.; Suzuki, K.; Liu, R.; Li, S.; Morenzoni, E.; Yi, J. B.

2017-09-01

Co doped ZnO films have been deposited by a laser-molecular beam epitaxy system. X-ray diffraction and UV spectra analysis show that Co effectively substitutes the Zn site. Transmission electron microscopy (TEM) and secondary ion mass spectroscopy analysis indicate that there are no clusters. Co dopants are uniformly distributed in ZnO film. Ferromagnetic ordering is observed in all samples deposited under an oxygen partial pressure, PO2=10-3 , 10-5, and 10-7 torr, respectively. However, the magnetization of PO2=10-3 and 10-5 is very small at room temperature. At low temperature, the ferromagnetic ordering is enhanced. Muon spin relaxation (μ SR ) measurements confirm the ferromagnetism in all samples, and the results are consistent with magnetization measurements. From μ SR and TEM analysis, the film deposited under PO2=10-7 torr shows intrinsic ferromagnetism. However, the volume fraction of the ferromagnetism phase is approximately 70%, suggesting that the ferromagnetism is not carrier mediated. Resistivity versus temperature measurements indicate Efros variable range hopping dominates the conductivity. From the above results, we can confirm that a bound magnetic polaron is the origin of the ferromagnetism.

Acids and alkali resistant sticky superhydrophobic surfaces by one-pot electropolymerization of perfluoroalkyl alkyl pyrrole.

Science.gov (United States)

Nicolas, Mael

2010-03-15

Over the past few years, electropolymerization of semifluorinated monomers like thiophene or pyrrole has been used as a gentle and effective method to generate, in one step, stable superhydrophobic surfaces. The synthetic route mostly involves the coupling reaction between a carboxylic acid and an alcohol, using a carboxy group-activated reagent and a catalyst. As a consequence, the electroformed surfaces present high liquid repellency due to the concomitant effect of roughness and low surface energy. Nevertheless, the ester connector can be cleaved under acidic and basic conditions, preventing its use under a range of environmental conditions. To overcome this drawback, a new perfluoroalkyl alkyl pyrrole has been synthesized, the fluorinated segment being connected to the electropolymerizable part via an alkyl chain, and electropolymerized, leading to surfaces that exhibit a static contact angle with water superior to 150 degrees and no sliding angle, over a wide pH range and with a long lifetime. This represents the first example of a pure conducting polymer surface with sticky superhydrophobicity not only in pure water but also in corrosive solutions such as acids and bases, giving rise to new prospects in practical applications. 2009 Elsevier Inc. All rights reserved.

Photoluminescence properties of ZnO films grown on InP by thermally oxidizing metallic Zn films

CERN Document Server

Chen, S J; Zhang, J Y; Lu, Y M; Shen, D Z; Fan, X W

2003-01-01

Photoluminescence (PL) properties of ZnO films grown on (001) InP substrates by thermal oxidization of metallic Zn films, in which oxygen vacancies and interstitial Zn ions are compensated by P ions diffusing from (001) InP substrates, are investigated. X-ray diffraction spectra indicate that P ions have diffused into the Zn films and chemically combined with Zn ions to form Zn sub 3 P sub 2. Intense free exciton emission dominates the PL spectra of ZnO films with very weak deep-level emission. Low-temperature PL spectra at 79 K are dominated by neutral-donor bound exciton emission at 3.299 eV (I sub 4) with a linewidth of 17.3 meV and neutral-acceptor bound exciton emission at 3.264 eV. The free exciton emission increases with increasing temperature and eventually dominates the emission spectrum for temperature higher than 170 K. Furthermore, the visible emission around 2.3 eV correlated with oxygen deficiencies and interstitial Zn defects was quenched to a remarkable degree by P diffusing from InP substrate...

Photoluminescence properties of ZnO films grown on InP by thermally oxidizing metallic Zn films

International Nuclear Information System (INIS)

Chen, S J; Liu, Y C; Zhang, J Y; Lu, Y M; Shen, D Z; Fan, X W

2003-01-01

Photoluminescence (PL) properties of ZnO films grown on (001) InP substrates by thermal oxidization of metallic Zn films, in which oxygen vacancies and interstitial Zn ions are compensated by P ions diffusing from (001) InP substrates, are investigated. X-ray diffraction spectra indicate that P ions have diffused into the Zn films and chemically combined with Zn ions to form Zn 3 P 2 . Intense free exciton emission dominates the PL spectra of ZnO films with very weak deep-level emission. Low-temperature PL spectra at 79 K are dominated by neutral-donor bound exciton emission at 3.299 eV (I 4 ) with a linewidth of 17.3 meV and neutral-acceptor bound exciton emission at 3.264 eV. The free exciton emission increases with increasing temperature and eventually dominates the emission spectrum for temperature higher than 170 K. Furthermore, the visible emission around 2.3 eV correlated with oxygen deficiencies and interstitial Zn defects was quenched to a remarkable degree by P diffusing from InP substrates

Damping constant of Co/Pt multilayer thin-film media

International Nuclear Information System (INIS)

Fujita, N.; Inaba, N.; Kirino, F.; Igarashi, S.; Koike, K.; Kato, H.

2008-01-01

Gilbert's damping constants, α, of Co(t Co )/Pt (1.4 nm) multilayer thin films are investigated by Q-band FMR analysis. α is calculated from the resonance width of the FMR spectrum. With decreasing t Co , the α value decreases from 0.034 (t Co =8.7 nm) to 0.023 (t Co =1.8 nm), and then increases to 0.037 (t Co =1.0 nm). The decrease of α with t Co >1.8 nm is probably due to the eddy current loss effects. The increase of α with t Co <1.8 nm would be caused by the increase of the distortion between the Co and the Pt layers at the interface. When the magnetic field direction was changed from θ=90 deg. (parallel to the specimen) to θ=0 deg. (perpendicular to the specimen), the α of all the specimens increased, and a sharp step in α was observed around θ=40 deg., where the α has the maximum value

Sensitive and selective electrochemical determination of quinoxaline-2-carboxylic acid based on bilayer of novel poly(pyrrole) functional composite using one-step electro-polymerization and molecularly imprinted poly(o-phenylenediamine)

Energy Technology Data Exchange (ETDEWEB)

Yang, Yukun; Fang, Guozhen; Wang, Xiaomin; Pan, Mingfei; Qian, Hailong; Liu, Huilin; Wang, Shuo, E-mail: s.wang@tust.edu.cn

2014-01-02

Graphical abstract: -- Highlights: •PPY-GO-BiCoPc composite was formed using a simple electrochemical method for the first time. •A novel PoPD-MIP sensor based on PPY-GO-BiCoPc composite had been fabricated. •The PPY-GO-BiCoPc functional composite was introduced to improve performance of the sensor. •Highly sensitive, selective and stable sensor had been achieved. •The established MIP sensor could be promising in food safety analysis. -- Abstract: A facile and efficient molecularly imprinted polymer (MIP) recognition element of electrochemical sensor was fabricated by directly electro-polymerizing monomer o-phenylenediamine (oPD) in the presence of template quinoxaline-2-carboxylic acid (QCA), based on one-step controllable electrochemical modification of poly(pyrrole)-graphene oxide-binuclear phthalocyanine cobalt (II) sulphonate (PPY-GO-BiCoPc) functional composite on glassy carbon electrode (GCE). The MIP film coated on PPY-GO-BiCoPc functional composite decorated GCE (MIP/PPY-GO-BiCoPc/GCE) was presented for the first time. The synergistic effect and electro-catalytic activity toward QCA redox of PPY-GO-BiCoPc functional composite were discussed using various contrast tests. Also, the effect of experimental variables on the current response such as, electro-polymerization cycles, template/monomer ratio, elution condition for template removal, pH of the supporting electrolyte and accumulation time, were investigated in detail. Under the optimized conditions, the proposed MIP sensor possessed a fast rebinding dynamics and an excellent recognition capacity to QCA, while the anodic current response of square wave voltammetry (SWV) was well-proportional to the concentration of QCA in the range of 1.0 × 10{sup −8}–1.0 × 10{sup −4} and 1.0 × 10{sup −4}–5.0 × 10{sup −4} mol L{sup −1} with a low detection limit of 2.1 nmol L{sup −1}. The established sensor was applied successfully to determine QCA in commercial pork and chicken muscle

Sensitive and selective electrochemical determination of quinoxaline-2-carboxylic acid based on bilayer of novel poly(pyrrole) functional composite using one-step electro-polymerization and molecularly imprinted poly(o-phenylenediamine)

International Nuclear Information System (INIS)

Yang, Yukun; Fang, Guozhen; Wang, Xiaomin; Pan, Mingfei; Qian, Hailong; Liu, Huilin; Wang, Shuo

2014-01-01

Graphical abstract: -- Highlights: •PPY-GO-BiCoPc composite was formed using a simple electrochemical method for the first time. •A novel PoPD-MIP sensor based on PPY-GO-BiCoPc composite had been fabricated. •The PPY-GO-BiCoPc functional composite was introduced to improve performance of the sensor. •Highly sensitive, selective and stable sensor had been achieved. •The established MIP sensor could be promising in food safety analysis. -- Abstract: A facile and efficient molecularly imprinted polymer (MIP) recognition element of electrochemical sensor was fabricated by directly electro-polymerizing monomer o-phenylenediamine (oPD) in the presence of template quinoxaline-2-carboxylic acid (QCA), based on one-step controllable electrochemical modification of poly(pyrrole)-graphene oxide-binuclear phthalocyanine cobalt (II) sulphonate (PPY-GO-BiCoPc) functional composite on glassy carbon electrode (GCE). The MIP film coated on PPY-GO-BiCoPc functional composite decorated GCE (MIP/PPY-GO-BiCoPc/GCE) was presented for the first time. The synergistic effect and electro-catalytic activity toward QCA redox of PPY-GO-BiCoPc functional composite were discussed using various contrast tests. Also, the effect of experimental variables on the current response such as, electro-polymerization cycles, template/monomer ratio, elution condition for template removal, pH of the supporting electrolyte and accumulation time, were investigated in detail. Under the optimized conditions, the proposed MIP sensor possessed a fast rebinding dynamics and an excellent recognition capacity to QCA, while the anodic current response of square wave voltammetry (SWV) was well-proportional to the concentration of QCA in the range of 1.0 × 10 −8 –1.0 × 10 −4 and 1.0 × 10 −4 –5.0 × 10 −4 mol L −1 with a low detection limit of 2.1 nmol L −1 . The established sensor was applied successfully to determine QCA in commercial pork and chicken muscle samples with acceptable

Pyrrole PMOs, incorporating new N-heterocyclic compounds on an ethene-PMO through Diels–Alder reactions

International Nuclear Information System (INIS)

Esquivel, Dolores; De Canck, Els; Jiménez-Sanchidrián, César; Romero-Salguero, Francisco J.; Van Der Voort, Pascal

2014-01-01

The ethenylene bridges on the walls of an ethenylene-bridged periodic mesoporous organosilica were successfully modified with a variety of pyrrole derivatives – pyrrole, methylpyrrole, dimethylpyrrole, trimethylpyrrole and 1-phenylpyrrole – through Diels–Alder reactions. X-ray diffraction measurements and N 2 adsorption–desorption analysis confirmed the preservation of the ordering and mesoporosity of the parent material as well as the decoration of the pores with the surface Diels–Alder adducts. Moreover, other techniques such as DRIFT, 13 C and 29 Si nuclear magnetic resonances revealed the formation of the surface N-heterocyclic compounds at the parent ethenylene sites. - Highlights: • Chemical modification of the double bonds on an ethene-PMO through the Diels–Alder reaction. • A family of pyrrole derivatives act as dienes in the Diels–Alder reaction. • Well-ordering and mesoporosity are retained after the post-functionalization. • N-containing compounds on the surface of ethene-PMO are present after the Diels–Alder reaction

Pyrrole PMOs, incorporating new N-heterocyclic compounds on an ethene-PMO through Diels–Alder reactions

Energy Technology Data Exchange (ETDEWEB)

Esquivel, Dolores; De Canck, Els [Center for Ordered Materials, Organometallics and Catalysis, Department of Inorganic and Physical Chemistry, Ghent University, Krijgslaan 281-S3, 9000 Ghent (Belgium); Jiménez-Sanchidrián, César [Department of Organic Chemistry, Nanochemistry and Fine Chemistry Research Institute (IUIQFN), Faculty of Sciences, University of Córdoba, Campus de Rabanales, Marie Curie Building, Ctra. Nnal. IV, km 396, 14071 Córdoba (Spain); Romero-Salguero, Francisco J., E-mail: qo2rosaf@uco.es [Department of Organic Chemistry, Nanochemistry and Fine Chemistry Research Institute (IUIQFN), Faculty of Sciences, University of Córdoba, Campus de Rabanales, Marie Curie Building, Ctra. Nnal. IV, km 396, 14071 Córdoba (Spain); Van Der Voort, Pascal, E-mail: pascal.vandervoort@ugent.be [Center for Ordered Materials, Organometallics and Catalysis, Department of Inorganic and Physical Chemistry, Ghent University, Krijgslaan 281-S3, 9000 Ghent (Belgium)

2014-11-14

The ethenylene bridges on the walls of an ethenylene-bridged periodic mesoporous organosilica were successfully modified with a variety of pyrrole derivatives – pyrrole, methylpyrrole, dimethylpyrrole, trimethylpyrrole and 1-phenylpyrrole – through Diels–Alder reactions. X-ray diffraction measurements and N{sub 2} adsorption–desorption analysis confirmed the preservation of the ordering and mesoporosity of the parent material as well as the decoration of the pores with the surface Diels–Alder adducts. Moreover, other techniques such as DRIFT, {sup 13}C and {sup 29}Si nuclear magnetic resonances revealed the formation of the surface N-heterocyclic compounds at the parent ethenylene sites. - Highlights: • Chemical modification of the double bonds on an ethene-PMO through the Diels–Alder reaction. • A family of pyrrole derivatives act as dienes in the Diels–Alder reaction. • Well-ordering and mesoporosity are retained after the post-functionalization. • N-containing compounds on the surface of ethene-PMO are present after the Diels–Alder reaction.

Synergistic effect of indium and gallium co-doping on the properties of RF sputtered ZnO thin films

Science.gov (United States)

Shaheera, M.; Girija, K. G.; Kaur, Manmeet; Geetha, V.; Debnath, A. K.; Karri, Malvika; Thota, Manoj Kumar; Vatsa, R. K.; Muthe, K. P.; Gadkari, S. C.

2018-04-01

ZnO thin films were synthesized using RF magnetron sputtering, with simultaneous incorporation of Indium (In) and Gallium (Ga). The structural, optical, chemical composition and surface morphology of the pure and co-doped (IGZO) thin films were characterized by X-Ray diffraction (XRD), UV-visible spectroscopy, Field Emission Scanning Electron Microscopy (FESEM), and Raman spectroscopy. XRD revealed that these films were oriented along c-axis with hexagonal wurtzite structure. The (002) diffraction peak in the co-doped sample was observed at 33.76° with a slight shift towards lower 2θ values as compared to pure ZnO. The surface morphology of the two thin films was observed to differ. For pure ZnO films, round grains were observed and for IGZO thin films round as well as rod type grains were observed. All thin films synthesized show excellent optical properties with more than 90% transmission in the visible region and band gap of the films is observed to decrease with co-doping. The co doping of In and Ga is therefore expected to provide a broad range optical and physical properties of ZnO thin films for a variety of optoelectronic applications.

Electrocatalytic activity and operational stability of electrodeposited Pd-Co films towards ethanol oxidation in alkaline electrolytes

Science.gov (United States)

Tsui, Lok-kun; Zafferoni, Claudio; Lavacchi, Alessandro; Innocenti, Massimo; Vizza, Francesco; Zangari, Giovanni

2015-10-01

Direct alkaline ethanol fuel cells (DEFCs) are usually run with Pd anodic catalysts, but their performance can be improved by utilizing alloys of Pd and Co. The oxyphilic Co serves to supply ample -OH to the ethanol oxidation reaction, accelerating the rate limiting step at low overpotential under alkaline conditions. Pd-Co films with compositions between 20 and 80 at% Co can be prepared by electrodeposition from a NH3 complexing electrolyte. Cyclic voltammetry studies show that the ethanol oxidation peak exhibits increasing current density with increasing Co content, reaching a maximum at 77% Co. In contrast, potentiostatic measurements under conditions closer to fuel cell operating conditions show that a 50 at% Co alloy has the highest performance. Importantly, the Co-Pd film is also found to undergo phase and morphological transformations during ethanol oxidation, resulting in a change from a compact film to high surface area flake-like structures containing Co3O4 and CoOOH; such a transformation instead is not observed when operating at a constant potential of 0.7 VRHE.

Anisotropies in sputtered FeCoV films and FeCoV/Ti:N multilayers

Energy Technology Data Exchange (ETDEWEB)

Clemens, D.; Vananti, A.; Terrier, C.; Boeni, P.; Schnyder, B.; Tixier, S.; Horisberger, M. [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

1997-09-01

SQUID and MOKE magnetometry as well as mechanical and X-ray stress analysis have been used in order to prove the magnetostrictive nature of the anisotropy in Fe{sub 0.50}Co{sub 0.48}V{sub 0.02} films and Fe{sub 0.50}Co{sub 0.48}V{sub 0.02} /Ti:N multilayers. The investigation stresses on the dependence on the sputter gas pressure and on the thickness of the deposited layer. (author) 1 fig., 6 refs.

Aluminum-doped Zn O polycrystalline films prepared by co-sputtering of a Zn O-Al target

Energy Technology Data Exchange (ETDEWEB)

Becerril, M.; Silva L, H.; Guillen C, A.; Zelaya A, O. [Instituto Politecnico Nacional, Centro de Investigacion y de Estudios Avanzados, Departamento de Fisica, Apdo. Postal 14-740, 07000 Mexico D. F. (Mexico)

2014-07-01

Aluminum-doped Zinc oxide polycrystalline thin films (Azo) were grown on 7059 Corning glass substrates at room temperature by co-sputtering from a Zn O-Al target. The target was designed as follows, high purity elemental Aluminum was evaporated onto a Zn O target covering small areas. The structural, optical and electrical properties were analyzed as a function of Al content. The Al doped Zn O polycrystalline films showed an n-type conductivity. It was found that the electrical resistivity drops and the carrier concentration increases as a consequence of Al incorporation within the Zn O lattice. In both cases, the changes are of several orders of magnitude. From the results, we conclude that, using these Zn O-Al targets, n-type Al doped Zn O polycrystalline films with high transmittance and low resistivity can be obtained. The crystalline structure of the films was determined by X-ray diffraction. Atomic Force Microscopy images were obtained with an Auto probe C P (Veeco Metrology Group) Microscope. (Author)

Mesoscopic layered structure in conducting polymer thin film fabricated by potential-programmed electropolymerization