WorldWideScience

Sample records for polonium tolerance estimations

  1. Estimation of polonium concentration in groundwater samples from the Peddagattu/Nambapur and Seripalli regions using alpha-spectrometry

    International Nuclear Information System (INIS)

    Raghavendra, T.; Srilatha, K.; Mahender, C.; Elender; Vijaya Lakshmi, T.; Himabindu, V.; Vishwa Prasad; Padma Savithri, P.; Datta, D.; Arunachalam, J.

    2013-01-01

    The decay of uranium series in the earth crust remains the final and long lived radionuclides 210 Po and 210 Pb in the environment. Their presence in the atmosphere is due to the decay of 222 Rn diffusing from the ground. This study was carried out with an objective of estimation of polonium concentration in a uranium mineralized zone in Peddagattu and Seripalli areas of Nalgonda district, Andhra Pradesh, India. Groundwater samples were collected from 12 wells, and frequency of these collections was once in a quarter from May 2010 to Dec 2011. The alpha-spectrometry has been applied to analyze these samples. Observation reveals that the activity concentration of Polonium in the water samples of Peddagattu and Seripally regions range from 0.3 mBq/l to 2.80 mBq/l with Geometric mean of 0.89 mBq/l and Geometric Standard deviation of 2.72 and from 0.3 mBq/l to 4.68 mBq/l with a Geometric mean of 0.91 and Geometric standard deviation of 3.22 respectively. As per WHO standards, the maximum permissible limit in drinking water for Polonium is 0.55 Bq/l. Hence all the 12 samples are falling well under the permissible limit. This paper presents the analytical details for estimating polonium as a natural radioactive element in groundwater as well as surface water samples collected from the Nambapur/Peddagattu and Seripalli regions. (author)

  2. Polonium-210 concentration of cigarettes traded in Cuba and their estimated dose contribution due to smoking

    International Nuclear Information System (INIS)

    Brigido Flores, O.; Montalvan Estrada, A.; Fabelo Bonet, O.; Barreras Caballero, A.

    2015-01-01

    Cigarette smoking is one of the pathways that might contribute significantly to the increase in the radiation dose reaching man, due to the relatively large concentrations of polonium-210 found in tobacco leaves. The results of 200 Po determination on the 11 most frequently smoked brands of cigarettes and cigars which constitute over 75% of the total cigarette consumption in Cuba are presented and discussed. Moreover, the polonium content in cigarette smoke was estimated on the basis of its activity in cigarettes, ash, fresh filters and post-smoking filters. 210 Po was determined by gas flow proportional detector after spontaneous deposition of 210 Po on a high copper-content disk. The annual committed equivalent dose for lungs and the annual effective dose for smokers between 12-17 years old and for adults were calculated on the basis of the 210 Po inhalation through cigarette smoke. The results showed concentration ranging from 9.3 to 14.4 mBq per cigarette with a mean value of 11.8 ± 0.6 mBq.Cig -1 . the results of this work indicate that Cuban smokers who smoke one pack (20 cigarettes) per day inhale from 62 to 98 mBq.d -1 of 210 Po and smokers between 12-17 years old who consume 10 cigarettes daily inhale from 30-50 mBq.d -1 . The average committed equivalent dose for lungs is estimated to be 466 ± 36 and 780 ± 60 μSv.year -1 for young and adult smokers, respectively and annual committed effective dose is calculated to be 60 ± 5 and 100 ± 8 μSv for these two groups of smokers, respectively. (Author)

  3. Primate polonium metabolic models and their use in estimation of systemic radiation doses from bioassay data. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Cohen, N. [New York Univ. Medical Center, Tuxedo, NY (United States). Dept. of Environmental Medicine

    1989-03-15

    A Polonium metabolic model was derived and incorporated into a Fortran algorithm which estimates the systemic radiation dose from {sup 210}Po when applied to occupational urine bioassay data. The significance of the doses estimated are examined by defining the degree of uncertainty attached to them through comprehensive statistical testing procedures. Many parameters necessary for dosimetry calculations (such as organ partition coefficients and excretion fractions), were evaluated from metabolic studies of {sup 210}Po in non-human primates. Two tamarins and six baboons were injected intravenously with {sup 210}Po citrate. Excreta and blood samples were collected. Five of the baboons were sacrificed at times ranging from 1 day to 3 months post exposure. Complete necropsies were performed and all excreta and the majority of all skeletal and tissue samples were analyzed radiochemically for their {sup 210}Po content. The {sup 210}Po excretion rate in the baboon was more rapid than in the tamarin. The biological half-time of {sup 210}Po excretion in the baboon was approximately 15 days while in the tamarin, the {sup 210}Po excretion rate was in close agreement with the 50 day biological half-time predicted by ICRP 30. Excretion fractions of {sup 210}Po in the non-human primates were found to be markedly different from data reported elsewhere in other species, including man. A thorough review of the Po urinalysis procedure showed that significant recovery losses resulted when metabolized {sup 210}Po was deposited out of raw urine. Polonium-210 was found throughout the soft tissues of the baboon but not with the partition coefficients for liver, kidneys, and spleen that are predicted by the ICRP 30 metabolic model. A fractional distribution of 0.29 for liver, 0.07 for kidneys, and 0.006 for spleen was determined. Retention times for {sup 210}Po in tissues are described by single exponential functions with biological half-times ranging from 15 to 50 days.

  4. Volatility Properties of Polonium

    International Nuclear Information System (INIS)

    Eichler, B.

    2002-06-01

    Thermodynamical constants to describe evaporation processes of polonium are summarized and critically discussed. Additionally, systematic changes of the properties of the chalcogenes are analyzed, empirical correlations are proofed and cyclic processes are balanced. Accordingly, the existing values of entropies for polonium are acceptable. Questionable, however, are those values of enthalpies, which have been deduced from results of the experimental investigations of the vapor pressure temperature dependency, of the melting point, and of the boiling temperatures. Technical difficulties and possible error sources of the measurements resulting from the radioactive decay properties of 210 Po are discussed. Using extrapolative standard enthalpies and entropies as well as their temperature dependency, the equilibrium partial pressure of the monomeric and dimeric polonium above the pure condensed phase and the equilibrium constant of the dimerization reaction in the gas phase are calculated: log p/pa Po (g) = (11.797 ± 0.024) -(9883.4 ± 9.5)/T (for T = 298-600 K); = (10.661 ± 0.057) - (9328.4 ± 4.9)/T (for T = 500-1300 K); log p/pa Po 2 (g) = (13.698 ± 0.049) - (8592.3 ± 19.6)/T (for T = 298-600 K); = (11.424 ± 0.124) - (7584.1 ± 98.1)/T (for T = 500-1300 K); log K (dim) = (-4.895 ± 0.012) + (11071 ± 6)/T. According to these calculations and in contrast to other works, polonium evaporates in the entire temperature range between 298 and 1300 K in the dimeric state. Hence, 'latent heats' of the volatilization processes are clearly larger compared to literature data. Especially in the temperature range of the solid polonium the calculated vapor pressure curve shifts significantly to lower values, whereas the boiling point was almost reproduced by the calculation. The results of the extrapolation for the standard enthalpy of the gaseous monomeric polonium and the dimerization enthalpy ΔH 0 298 Po (g) = 188.9 kJ/mol and ΔH 0 298 (form) Po 2 (g) = 211.5 kJ/mol are

  5. Internal dosimetry of polonium-210

    International Nuclear Information System (INIS)

    Pucelj, B.

    2007-01-01

    On November 1, 2006, former Russian agent Alexander Litvinenko suddenly fell ill and was hospitalised. He died three weeks later, becoming the first known victim of lethal polonium-210 induced acute radiation syndrome. Po-210 is an alpha emitter and is not a radiological hazard as long as it remains outside the body. If taken into the body, much of Po-210 is subsequently excreted, mostly through faeces and some through urine and other pathways. After uptake by the blood, Po-210 is widely distributed through soft body tissues including bone marrow. The internal dose from polonium in the body gives rise to an increase in lifetime cancer risk. Very high radiation doses can cause severe damage to body tissues and organs and in the extreme can be fatal. The hazard function model was used to estimate the lethal levels of intake of Po-210. In case of Litvinenko the destruction of bone marrow and resulting failure of the immune system was most probably the main cause of death, likely to be compounded by damage caused by higher doses to other organs, including kidneys and liver. It was estimated that the ingestion of several hundreds MBq or just about a microgram of Po-210 can be lethal. (author)

  6. Deposition potential of polonium

    Energy Technology Data Exchange (ETDEWEB)

    Heal, H. G.

    1948-11-23

    The cathodic deposition potential for polonium in concentrations of 10{sup -13} normal and 8 x 10{sup -13} normal, the former being 100-fold smaller than the smallest concentrations previously studied, has been determined. The value is 0.64 volt on the hydrogen scale. Considering the various ways in which the graphs can reasonably be drawn, we consider the maximum possible error to be of the order of +- 0.03 volt. There is apparently no shift of deposition potential between concentrations of 10{sup -8} and 10{sup -13} normal, indicating that the Nernst equation is not applicable in these circumstances.

  7. Polonium-210 budget in cigarettes

    International Nuclear Information System (INIS)

    Khater, A.E.M.

    2004-01-01

    Due to the relatively high activity concentrations of 210 Po and 210 Pb that are found in tobacco and its products, cigarette smoking highly increases the internal intake of both radionuclides and their concentrations in the lung tissues. That might contribute significantly to an increase in the internal radiation dose and in the number of instances of lung cancer observed among smokers. Samples of most frequently smoked fine and popular brands of cigarettes were collected from those available on the Egyptian market. 210 Po activity concentrations were measured by alpha spectrometry, using surface barrier detectors, following the radiochemical separation of polonium. Samples of fresh tobacco, wrapping paper, fresh filters, ash and post-smoking filters were spiked with 208 Po for chemical recovery calculation. The samples were dissolved using mineral acids (HNO 3 , HCl and HF). Polonium was spontaneously plated-out on stainless steel disks from diluted HCl solution. The 210 Po activity concentration in smoke was estimated on the basis of its activity in fresh tobacco and wrapping paper, fresh filter, ash and post-smoking filters. The percentages of 210 Po activity concentrations that were recovered from the cigarette tobacco to ash, post-smoking filters, and smokes were assessed. The results of this work indicate that the average (range) activity concentration of 210 Po in cigarette tobacco was 16.6 (9.7-22.5) mBq/cigarette. The average percentages of 210 Po content in fresh tobacco plus wrapping paper that were recovered by post-smoking filters, ash and smoke were 4.6, 20.7 and 74.7, respectively. Cigarette smokers, who are smoking one pack (20 cigarettes) per day, are inhaling on average 123 mBq/d of 210 Po and 210 Pb each. The annual effective doses were calculated on the basis of 210 Po and 210 Pb intake with the cigarette smoke. The mean values of the annual effective dose for smokers (one pack per day) were estimated to be 193 and 251 μSv from 210 Po and 210

  8. Levels of polonium-210 in some beverages and in tobacco

    International Nuclear Information System (INIS)

    Colangelo, C.H.; Huguet, M.R.; Palacios, M.A.; Oliveira, A.A.

    1992-01-01

    The objective of the present work is the estimation of the Polonium-210 content in some beverages and in tobacco, in order to assess the corresponding collective doses to the population in Argentina. Yerba mate, an autochton plant of South America, tea leaves, their infusion and ground coffee were analyzed as well as tobacco. Collective doses due to annual consumption of the beverages described, resulted in values from 6 man.Sv to 1200 man.Sv. Results for Polonium-210 in tobacco ranged from 10 Bq kg -1 . Doses due to the use of tobacco were not assessed since an appropriate metabolic model was not found. (author)

  9. Bacterial mobilization of polonium

    International Nuclear Information System (INIS)

    LaRock, P.; Hyun, J.H.; Burnett, W.C.

    1996-01-01

    Polonium has been observed as the sole α-emitting nuclide in groundwaters of central Florida, in the absence of its radiogenic parents, at levels of 1,000 dpm/1 or more. Because of the chemical similarity of Po to S (both occupy the same column in the periodic table), studies were begun to determine whether bacteria, particularly those species active in sulfur cycling, could account for the selective solubilization and mobilization of Po. Possible sources of Po are the U-rich phosphate rock and phosphogypsum (gypsum), a byproduct in the manufacture of phosphoric acid. This paper reports on a series of experiments involving the interaction of bacteria with this waste gypsum that resulted in the solubilization of Po. Bacteria were isolated from gypsum that were capable of mediating Po release in column experiments of Po. Bacteria were isolated from gypsum that were capable of mediating Po release in column experiments when fed a growth medium. Sulfate-reducing bacteria were particularly effective at mediating Po release provided the sulfide levels did not rise above 10 μM, in which case Po was apparently coprecipitated as a metal sulfide. Conversely, the ability of sulfate-reducing bacteria to effectively remove dissolved Po when sulfide levels are high suggests that these bacteria may be used as an effective bioremediation tool at reducing groundwater Po levels. 22 refs., 10 figs

  10. Polonium-210 as a poison

    International Nuclear Information System (INIS)

    Harrison, John; Leggett, Rich; Lloyd, David; Phipps, Alan; Scott, Bobby

    2007-01-01

    The death of Alexander Litvinenko on 23 November 2006 has brought into focus scientific judgements concerning the radiotoxicity of polonium-210 ( 210 Po). This paper does not consider the specific radiological circumstances surrounding the tragic death of Mr Litvinenko; rather, it provides an evaluation of published human and animal data and models developed for the estimation of alpha radiation doses from 210 Po and the induction of potentially fatal damage to different organs and tissues. Although uncertainties have not been addressed comprehensively, the reliability of key assumptions is considered. Concentrating on the possibility of intake by ingestion, the use of biokinetic and dosimetric models to estimate organ and tissue doses from 210 Po is examined and model predictions of the time-course of dose delivery are illustrated. Estimates are made of doses required to cause fatal damage, taking account of the possible effects of dose protraction and the relative biological effectiveness (RBE) of alpha particles compared to gamma and x-rays. Comparison of LD 50 values (dose to cause death for 50% of people) for different tissues with the possible accumulation of dose to these tissues suggests that bone marrow failure is likely to be an important component of multiple contributory causes of death occurring within a few weeks of an intake by ingestion. Animal data on the effects of 210 Po provide good confirmatory evidence of intakes and doses required to cause death within about 3 weeks. The conclusion is reached that 0.1-0.3 GBq or more absorbed to blood of an adult male is likely to be fatal within 1 month. This corresponds to ingestion of 1-3 GBq or more, assuming 10% absorption to blood. Well-characterised reductions in white cell counts would be observed. Bone marrow failure is likely to be compounded by damage caused by higher doses to other organs, including kidneys and liver. Even if the bone marrow could be rescued, damage to other organs can be expected

  11. The environmental behaviour of polonium

    International Nuclear Information System (INIS)

    Phaneuf, M.; Twining, J.; )

    2013-01-01

    In view of the importance of 210 Po as a dose contributor, the IAEA is completing a second specific Technical Reports Series document, entitled 'The Environmental Behaviour of Polonium'. This document covers the behaviour of polonium in terrestrial, freshwater and marine environments, and provides up-to-date information on key transfer processes, concepts and models that have been found to be important in radiological assessments for both humans and non-human biota. Additionally, applications of Po isotopes to environmental issues are discussed in order to alert readers to studies that use Po isotopes as tracers of environmental processes

  12. Radon risk: the polonium effects

    International Nuclear Information System (INIS)

    Pradel, J.

    2003-01-01

    The atoms of radon present in the earth's crust give after disintegration atoms of polonium 210 and lead 210 having a strong toxicity by ingestion ( superior of a factor 2 to 10 comparatively to plutonium 239). We have to remember that polonium and lead 210 are present everywhere in very important quantities relatively to values quoted for ground pollution. This must reassure us for the risks run from the nuclear facilities for which important efforts are made in matter of radiation protection. (N.C.)

  13. Polonium assimilation and retention in mule deer and pronghorn antelope

    International Nuclear Information System (INIS)

    Sejkora, K.J.

    1982-01-01

    Excretion kinetics and tissue distribution of polonium-210 in mule deer and pronghorn were studied. Each animal in a captive herd of 7 mule deer and 2 pronghorn received an intraruminal injection of 4.4 μCi of polonium chloride. Feces and urine were collected periodically over a 43-day period and daily excretion rate for each pathway was regressed as a function of time. Assimilation fractions of 0.40 and 0.51 were calculated for mule deer (n=2) and 0.60 for a pronghorn. Body burden retention functions were calculated from integrated excretion rate functions. Polonium burdens in muscle, liver, and kidney were calculated as a fraction of body burden from serially-sacrificed animals. Background tissue burdens in mule deer were comparable to those of other ruminants reported in the literature. Hypothetical cases were assumed which combined feeding rate of mule deer, forage concentrations of polonium, retention function, tissue burden fraction, and human intake to estimate human radiation dose. 26 references

  14. Radiocaesium and polonium in seals from Swedish coastal waters

    International Nuclear Information System (INIS)

    Holm, E.A.B.; Leisvik, M.A.; Holm, E.A.B

    2004-01-01

    Radiocaesium, 137 Cs (T 1/2 = 30 a) and 210 Po (T 1/2 = 138 d) have been studied in tissues (muscle, liver, kidney and gonads/ovaries) from a large number of seals from the Baltic Sea and the Swedish west coast during 1995-2002. The Baltic Sea is a marginal sea with long residence time for dissolved compounds. Concentrations of radiocaesium increased 10 fold in the Baltic Sea following the Chernobyl accident, while concentrations of polonium can be supposed to be in equilibrium except for seasonal variations. The major food for seals in the Baltic proper is fish, while at the west coast other food stuff such as crustaceans play an important role. By supposing that the seals consume 5% of their body-weight per day and by using known data for caesium and polonium in fish the biological half-life in seals is estimated to 20 days for Caesium and 35 days for Polonium. Radiocaesium is evenly distributed in the organs of the seals and was about 100 Bq kg -1 in the Baltic Sea while at the west coast the concentrations were significantly lower, about 5-30 Bq kg -1 . Polonium shows the highest concentrations in kidney, about 100-200 Bq kg -1 d.w. in the Baltic sea and higher concentrations 100-1000 Bq kg -1 at the west coast. This reflects clearly the differences in food choice/availability in the different areas. The estimated maximal doses were 76 μSv per year to muscle from 137 Cs and 6.8 mSv from 210 Po to kidney. Seals constitute a good bio-marker for radioactivity in Swedish coastal waters. Concentration factors are higher for radiocaesium in the Baltic Sea due to lower salinity and consequently higher concentrations in fish compared to other areas, but lower for polonium than in areas where crustaceans also constitute an important foodstuff. (author)

  15. Sulfur, selenium, tellurium and polonium

    International Nuclear Information System (INIS)

    Berry, F.J.

    1987-01-01

    This chapter on the coordination compounds of sulfur, selenium, tellurium and polonium starts with an introduction to the bonding, valence and geometry of the elements. Complexes of the group VIB elements are discussed with particular reference to the halo and pseudohalide complexes, oxo acid complexes, oxygen and nitrogen donor complexes and sulfur and selenium donor complexes. There is a section on the biological properties of the complexes discussed. (UK)

  16. Polonium: 110th anniversary of its discovery

    International Nuclear Information System (INIS)

    Mould, R. F.

    2008-01-01

    It is appropriate that the 110 Th anniversary of the discovery of polonium by Marie and Pierre Curie is commemorated in a Polish journal since this element was named for Poland and was also the element discovered by the Curies before they discovered radium. Polonium's discovery and characteristics are described. Polonium has never been used in medicine, and was largely forgotten apart from a few minor industrial uses, and as a trigger for a nuclear weapon, until the murder in November 2006 in London using 210 Polonium, of the ex-KGB officer Alexander Litvinenko. Polonium had previously been linked, without any definite proof, with the deaths of a few scientists who had worked with the element, including Irene and Frederick Joliet-Curie. This review ends with possible evidence for such links. (authors)

  17. Polonium-210 in tobacco

    International Nuclear Information System (INIS)

    Harley, N.H.; Cohen, B.S.; Tso, T.C.

    1978-01-01

    The purpose of this paper was to present the measurements that have been made on tobacco and tobacco products and to indicate the studies that show the amount of 210 Po transferred to mainstream smoke and inhaled. The amounts reported to be in the lung are summarized. The authors have shown what average values might be expected in the lung due to normal deposition and clearance of the smoke aerosol and to compare these values with the measurements. The average dose to cells in the bronchial epithelium was estimated for the activities reported to be on the bronchial surface, and a comparison of this dose with a known tumorigenic alpha dose was made

  18. Lead-210 and polonium-210 in grass

    Energy Technology Data Exchange (ETDEWEB)

    Hill, C R

    1960-07-16

    It appears that an important contribution to the observed ..cap alpha..-activity of grass may be provided by a process of natural fall-out in which lead-210 resulting from decay of atmospheric radon, together with a fraction of the equilibrium amount of its descendant polonium-210 are deposited by rainfall directly on to foliage. Metabolic uptake of part of this activity by sheep is indicated by the presence in the kidney of polonium-210. 6 references, 1 figure, 2 tables.

  19. Research on the behavior of polonium produced in lead-bismuth eutectic irradiated with neutrons. JAERI's nuclear research promotion program, H10-026. Contract research

    International Nuclear Information System (INIS)

    Sekimoto, Hiroshi; Igashira, Masayuki; Yano, Toyohiko; Obara, Toru; Ohsaki, Toshiro

    2002-03-01

    Lead-Bismuth Eutectic (LBE) is proposed by several research institutes as a coolant of liquid metal cooled fast reactors, instead of sodium, and a target of accelerator driven subcritical nuclear reactor systems (ADS). LBE has some advantages that it is chemically inert compared to sodium and that its melting point is low like sodium. A problem might be that bismuth produces polonium, which is an alpha emitter, by irradiation of neutrons. The purpose of the study is to get information for quantitative estimations of the release of polonium on LBE cooled fast reactors and on ADSs by making it clear about production rate of polonium (information about cross section) by neutron irradiation of LBE, release rate of the produced polonium from LBE, and adsorption rate of the polonium on various materials. To get the information about production rate of polonium, neutron cross sections of bismuth were measured in keV energy region, which was important in fast reactors, by using the Pelletron accelerator in Research Laboratory for Nuclear Reactors, Tokyo Institute of Technology. The obtained neutron capture cross sections were from 1/2 to 1/3 of the evaluated values in JENDL and the obtained polonium production cross sections were almost 1/3 of it. At the same time, an experimental device was designed for heating and adsorption experiments and the performance was tested. The performance of alpha spectrometer was tested also. By those the method was established for the measurement of polonium released from melted LBE after neutron irradiation. (author)

  20. Thermochromatography study of volatile polonium species in various gas atmospheres

    CERN Document Server

    Maugeri, Emilio Andrea; Eichler, Robert; Piguet,David; Mendonça, Tania Melo; Stora, Thierry; Schumann, Dorothea

    2014-01-01

    Phenomena related to the volatilization of polonium and its compounds are critical issues for the safety assessment of the innovative lead–bismuth cooled type of nuclear reactor or accelerator driven systems. The formation and volatilization of different species of polonium and their interaction with fused silica was studied by thermochromatography using carrier gases with varied redox potential. The obtained results show that under inert and reducing conditions in the absence of moisture, elemental polonium is formed. Polonium compounds more volatile than elemental polonium can be formed if traces of moisture are present in both inert and reducing carrier gas. The use of dried oxygen as carrier gas leads to the formation of polonium oxides, which are less volatile than elemental polonium. It was also found that the volatility of polonium oxides increases with increasing oxidation state. In the presence of moisture in an oxidizing carrier gas, species are formed that are more volatile than the oxides and le...

  1. Polonium-210 and lead-210 in food and tobacco products: a review of parameters and an estimate of potential exposure and dose

    Energy Technology Data Exchange (ETDEWEB)

    Watson, A.P.

    1983-07-01

    Food-chain transport of Pb-210 and Po-210 from soil to edible plant parts and from animal feed to meat and milk were evaluated from a review of literature. The degree of transfer was characterized by estimating concentration factors (unweighted arithmetic means) as well as the transfer coefficients B/sub v/, B/sub r/ (unweighted geometric means, f/sub m/ and f/sub f/ (unweighted arithmetic means). Global dietary intake of Pb-210 and Po-210 was also summarized, and 50-year dose estimates to target organs calculated. The greatest estimated ingestion doses were those to populations with large dietary complements of animal protein in the form of seafood (Japan) or caribou/reindeer muscle and organ meats (Arctic Eskimos and Lapps). The magnitude of this latter source illustrates the importance of simple food chains in generating significant exposures to populations dependent upon them. The origin and magnitude of inhalation exposure and dose from tobacco products was also assessed. For the majority of internal organs evaluated, the dose resulting from smoking commercially available tobacco products is comparable to or greater than the dose estimates for ingestion of naturally occurring dietary Pb-210 and Po-210.

  2. Polonium-210 and lead-210 in food and tobacco products: a review of parameters and an estimate of potential exposure and dose

    International Nuclear Information System (INIS)

    Watson, A.P.

    1983-07-01

    Food-chain transport of Pb-210 and Po-210 from soil to edible plant parts and from animal feed to meat and milk were evaluated from a review of literature. The degree of transfer was characterized by estimating concentration factors (unweighted arithmetic means) as well as the transfer coefficients B/sub v/, B/sub r/ (unweighted geometric means, f/sub m/ and f/sub f/ (unweighted arithmetic means). Global dietary intake of Pb-210 and Po-210 was also summarized, and 50-year dose estimates to target organs calculated. The greatest estimated ingestion doses were those to populations with large dietary complements of animal protein in the form of seafood (Japan) or caribou/reindeer muscle and organ meats (Arctic Eskimos and Lapps). The magnitude of this latter source illustrates the importance of simple food chains in generating significant exposures to populations dependent upon them. The origin and magnitude of inhalation exposure and dose from tobacco products was also assessed. For the majority of internal organs evaluated, the dose resulting from smoking commercially available tobacco products is comparable to or greater than the dose estimates for ingestion of naturally occurring dietary Pb-210 and Po-210

  3. On the methods for the estimation of salinity tolerance of ciliates

    OpenAIRE

    Smurov, Alexei

    2000-01-01

    Critical review of research methods for tolerance and potential tolerance of ciliates is given. Using several Paramecium species as an example the original approaches to potential tolerance estimation is presented. Connection between resistance, tolerance and potential tolerance is shown. Model for explanation of the connection is proposed. Several application aspects of diagrams of the connection between acclimation salinity and value of upper salinity tolerant limit in the ciliates are cons...

  4. Parameter Estimation Analysis for Hybrid Adaptive Fault Tolerant Control

    Science.gov (United States)

    Eshak, Peter B.

    Research efforts have increased in recent years toward the development of intelligent fault tolerant control laws, which are capable of helping the pilot to safely maintain aircraft control at post failure conditions. Researchers at West Virginia University (WVU) have been actively involved in the development of fault tolerant adaptive control laws in all three major categories: direct, indirect, and hybrid. The first implemented design to provide adaptation was a direct adaptive controller, which used artificial neural networks to generate augmentation commands in order to reduce the modeling error. Indirect adaptive laws were implemented in another controller, which utilized online PID to estimate and update the controller parameter. Finally, a new controller design was introduced, which integrated both direct and indirect control laws. This controller is known as hybrid adaptive controller. This last control design outperformed the two earlier designs in terms of less NNs effort and better tracking quality. The performance of online PID has an important role in the quality of the hybrid controller; therefore, the quality of the estimation will be of a great importance. Unfortunately, PID is not perfect and the online estimation process has some inherited issues; the online PID estimates are primarily affected by delays and biases. In order to ensure updating reliable estimates to the controller, the estimator consumes some time to converge. Moreover, the estimator will often converge to a biased value. This thesis conducts a sensitivity analysis for the estimation issues, delay and bias, and their effect on the tracking quality. In addition, the performance of the hybrid controller as compared to direct adaptive controller is explored. In order to serve this purpose, a simulation environment in MATLAB/SIMULINK has been created. The simulation environment is customized to provide the user with the flexibility to add different combinations of biases and delays to

  5. Polonium-210 in food and tobacco

    Energy Technology Data Exchange (ETDEWEB)

    Ali, S K [Sudan Academy of Science, Atomic Energy Research Coordination Council, Khartoum (Sudan)

    2006-04-15

    The objective of this study is concerned with the radioactivity in food and tobacco, derived mainly from {sup 210}Po which contribute to the radiation dose received through diet and smoking. This subject was covered under four chapters. Chapter one deals with historical background of polonium-210 and its behavior in living system. Sources of polonium-210 in food and tobacco are explained in the second chapter. Relevant issues such as separation and measurement of polonium-210 covered in subsequent chapter. Chapter four reviewed recent studies on polonium-210. It was found that the main source of this radionuclide is the phosphatic fertilizers that used in food and tobacco cultivation. These fertilizers contain the decay products of {sup 238}U series of which {sup 210}Po is known to be very important from environmental point of view. Many studies conducted showed that the committed effective dose derived mainly from {sup 210} Po due to the consumption of food, particularly sea food is significant, furthermore {sup 210}Po in tobacco is known to be the main cause of many diseases such as lung cancer.(Author)

  6. Polonium-210 in food and tobacco

    International Nuclear Information System (INIS)

    Ali, S.K.

    2006-04-01

    The objective of this study is concerned with the radioactivity in food and tobacco, derived mainly from 210 Po which contribute to the radiation dose received through diet and smoking. This subject was covered under four chapters. Chapter one deals with historical background of polonium-210 and its behavior in living system. Sources of polonium-210 in food and tobacco are explained in the second chapter. Relevant issues such as separation and measurement of polonium-210 covered in subsequent chapter. Chapter four reviewed recent studies on polonium-210. It was found that the main source of this radionuclide is the phosphatic fertilizers that used in food and tobacco cultivation. These fertilizers contain the decay products of 238 U series of which 210 Po is known to be very important from environmental point of view. Many studies conducted showed that the committed effective dose derived mainly from 210 Po due to the consumption of food, particularly sea food is significant, furthermore 210 Po in tobacco is known to be the main cause of many diseases such as lung cancer.(Author)

  7. Radiocesium and polonium in seals from the Baltic Sea. A preliminary study; Radiocaesium och polonium i sael fran Oestersjoen, en preliminaer studie

    Energy Technology Data Exchange (ETDEWEB)

    Holm, E. [Risoe National Lab., Roskilde (Denmark); Leisvik, M. [Lunds Univ., Avd. foer Radiofysik, Lund (Sweden)

    2002-04-01

    {sup 137}Cs and {sup 210}Po in muscle, liver and kidney from 5 seals from the Baltic Sea have been studied. Assuming that the seals consume 5% of their own body weight each day and by using previously obtained data for the doses in fish, the biological half time has been estimated to 20 days for Cesium and 35 days for Polonium. The maximum yearly doses are calculated to 76 {mu}Gy from {sup 137}CS to muscle and 3 500 {mu}Gy to kidneys from {sup 210}Po. These data are very preliminary, the number of individuals being so small, and it is difficult to estimate how much food other than fish the seals consume. Furthermore only few data for radioactive concentrations in whole fish exist, which especially impacts the results for Polonium. (LN)

  8. Human absorption and retention of polonium-210 from caribou meat.

    Science.gov (United States)

    Thomas, P A; Fisenne, I; Chorney, D; Baweja, A S; Tracy, B L

    2001-01-01

    The gastrointestinal (GI) absorption factors and the biological retention times for polonium were determined for a group of 14 volunteers--seven men and seven women--from Saskatoon, Saskatchewan, Canada. Each volunteer consumed 2.0 kg of caribou meat containing known amounts of naturally occurring 210Po. Urine and faecal samples were collected for up to 65 days after meat consumption and analysed for 210Po. The average GI absorption factor for the 14 volunteers was 56 +/- 4% (range = 31-71%), not significantly different from the ICRP value of 50%. About 3% of absorbed polonium underwent prompt excretion by the urinary pathway. The remainder was retained by the body with a half-time >100 days, compared to the ICRP value of 50 days. The effect of these findings increases the dose estimate for ingestion of 210Po in food by a factor of 1.5 to 3.5. Thus, background doses to people consuming caribou and reindeer may be higher than previously thought.

  9. Human absorption and retention of polonium-210 from caribou meat

    International Nuclear Information System (INIS)

    Thomas, P.A.; Fisenne, I.; Chorney, D.; Baweja, A.S.; Tracy, B.L.

    2001-01-01

    The gastrointestinal (GI) absorption factors and the biological retention times for polonium were determined for a group of 14 volunteers - seven men and seven women - from Saskatoon, Saskatchewan, Canada. Each volunteer consumed 2.0 kg of caribou meat containing known amounts of naturally occurring 210 Po. Urine and faecal samples were collected for up to 65 days after meat consumption and analysed for 210 Po. The average GI absorption factor for the 14 volunteers was 56±4% (range = 31-71%), not significantly different from the ICRP value of 50%. About 3% of absorbed polonium underwent prompt excretion by the urinary pathway. The remainder was retained by the body with a half-time >100 days, compared to the ICRP value of 50 days. The effect of these findings increases the dose estimate for ingestion of 210 Po in food by a factor of 1.5 to 3.5. Thus, background doses to people consuming caribou and reindeer may be higher than previously thought. (author)

  10. Lead-210, polonium-210, and stable lead in the food-chain lichen, reindeer and man

    International Nuclear Information System (INIS)

    Persson, B.R.

    1972-01-01

    The measurements of stable lead and the natural fallout radionuclides lead-210 and polonium-210 in communities of lichen (Cladonia alpestris) in central Sweden from 1961 to 1970 indicate a quite constant level. The average lead-210 content per unit area in lichen carpets was found to be 15 +- 2 nCi m -2 , the average lead-210 activity concentration 6.7 +- 0.9 nCi per kg dry weight and the lead-210 specific activity 630 +- 60 nCi per g of stable lead. The polonium-210/lead-210 activity ratio was about 0.9 +- 0.1. The vertical distribution of lead-210 in the lichen carpet showed a maximum concentration in the top layer. The distribution was similar during 1967 and 1968 but the low amount of precipitation during 1968 and 1969 disturbed the distribution pattern in 1969 and 1970. The transfer of lead-210, polonium-210 and stable lead through the food chain: lichen, reindeer, and man was characterized. The absorbed dose rate in Lapps due to polonium-210 was estimated to be about 6 to 8 mrad per year in gonads and 8 to 20 mrad per year in bone tissues. This is about ten percent of their entire absorbed dose contribution from all natural radiation sources. (U.S.)

  11. Study of polonium-210 in tobacco in Tunisia

    International Nuclear Information System (INIS)

    Rahali, Saifeddine

    2014-01-01

    Polonium-210 is a radio-isotopes natural α emitter, it cans be found in tobacco with a significant range. The high activity of 210 Po in tobacco and cigarettes causes the absorption of a high dose of alpha radiation that caused probably lung cancer, the objective of this study is to estimate the activity of 210 Po in tobacco matrix. Thirteen samples of cigarettes consumed in tunisia were experimented to determine the activity of this radionuclide. The PIPS, a silicon semiconductor, is used as on α spectrometry detector for the detection of 210 Po in all of our samples. The final results showed a high radioactivity of 210 Po from 11.77 to 25.31 mBq/g. We conclude that the effective annual average is estimated at 106.53 μSv / year.

  12. Plant Distribution Data Show Broader Climatic Limits than Expert-Based Climatic Tolerance Estimates.

    Directory of Open Access Journals (Sweden)

    Caroline A Curtis

    Full Text Available Although increasingly sophisticated environmental measures are being applied to species distributions models, the focus remains on using climatic data to provide estimates of habitat suitability. Climatic tolerance estimates based on expert knowledge are available for a wide range of plants via the USDA PLANTS database. We aim to test how climatic tolerance inferred from plant distribution records relates to tolerance estimated by experts. Further, we use this information to identify circumstances when species distributions are more likely to approximate climatic tolerance.We compiled expert knowledge estimates of minimum and maximum precipitation and minimum temperature tolerance for over 1800 conservation plant species from the 'plant characteristics' information in the USDA PLANTS database. We derived climatic tolerance from distribution data downloaded from the Global Biodiversity and Information Facility (GBIF and corresponding climate from WorldClim. We compared expert-derived climatic tolerance to empirical estimates to find the difference between their inferred climate niches (ΔCN, and tested whether ΔCN was influenced by growth form or range size.Climate niches calculated from distribution data were significantly broader than expert-based tolerance estimates (Mann-Whitney p values << 0.001. The average plant could tolerate 24 mm lower minimum precipitation, 14 mm higher maximum precipitation, and 7° C lower minimum temperatures based on distribution data relative to expert-based tolerance estimates. Species with larger ranges had greater ΔCN for minimum precipitation and minimum temperature. For maximum precipitation and minimum temperature, forbs and grasses tended to have larger ΔCN while grasses and trees had larger ΔCN for minimum precipitation.Our results show that distribution data are consistently broader than USDA PLANTS experts' knowledge and likely provide more robust estimates of climatic tolerance, especially for

  13. Analysis of polonium-210 in food samples

    International Nuclear Information System (INIS)

    Bueno, Luciana; Cunha, Ieda Irma Lamas

    1999-01-01

    This paper presents the polonium levels in food products. The analysis procedure consisted of acid leaching of the samples, solution evaporation, addition of hydrochloric acid, spontaneous deposition of polonium on a silver disk counting by alpha spectroscopy. The method was applied in reference materials and in foodstuffs, resulting in the following values: tea samples 0.4 to 1.7 Bq/unit; fish = 0.17 to 0.40 Bq/Kg, fruits = 0.048 to 0.067 Bq/kg, vegetables = 0.12 to 0.31 Bq/kg, cereal = 0.036 to 0.042 Bq/kg and legumes = 0.024 to 0.51 Bq/kg. The results are very important for public health due to the possible effects to the human organism by the ingestion of contaminated foodstuffs. (author)

  14. Polonium evaporation and adhesion experiments for the development of polonium filter in lead-bismuth cooled reactors

    International Nuclear Information System (INIS)

    Obara, Toru; Koga, Takeru; Miura, Terumitsu; Sekimoto, Hiroshi

    2008-01-01

    Fundamental experiments were performed to determine the adhesion characteristics of polonium to different metals and to develop a filter for polonium evaporated from neutron-irradiated LBE. The results of the first experiments suggested that adhesion characteristics are almost the same for stainless steel and nickel metal. The results of the preliminary experiments for a polonium filter suggested that stainless steel mesh with thin wires could effectively collect polonium evaporated from neutron-irradiated LBE. In the experiments, stainless steel wire mesh was used, but from the results of adhesion experiment, it is expected that the same effect can be obtained with wire mesh made of other kinds of metal. (author)

  15. Calculation of weighted averages approach for the estimation of ping tolerance values

    Science.gov (United States)

    Silalom, S.; Carter, J.L.; Chantaramongkol, P.

    2010-01-01

    A biotic index was created and proposed as a tool to assess water quality in the Upper Mae Ping sub-watersheds. The Ping biotic index was calculated by utilizing Ping tolerance values. This paper presents the calculation of Ping tolerance values of the collected macroinvertebrates. Ping tolerance values were estimated by a weighted averages approach based on the abundance of macroinvertebrates and six chemical constituents that include conductivity, dissolved oxygen, biochemical oxygen demand, ammonia nitrogen, nitrate nitrogen and orthophosphate. Ping tolerance values range from 0 to 10. Macroinvertebrates assigned a 0 are very sensitive to organic pollution while macroinvertebrates assigned 10 are highly tolerant to pollution.

  16. Radiocesium and polonium in seals from the Baltic Sea. A preliminary study

    International Nuclear Information System (INIS)

    Holm, E.; Leisvik, M.

    2002-01-01

    137 Cs and 210 Po in muscle, liver and kidney from 5 seals from the Baltic Sea have been studied. Assuming that the seals consume 5% of their own body weight each day and by using previously obtained data for the doses in fish, the biological half time has been estimated to 20 days for Cesium and 35 days for Polonium. The maximum yearly doses are calculated to 76 μGy from 137 CS to muscle and 3 500 μGy to kidneys from 210 Po. These data are very preliminary, the number of individuals being so small, and it is difficult to estimate how much food other than fish the seals consume. Furthermore only few data for radioactive concentrations in whole fish exist, which especially impacts the results for Polonium. (LN)

  17. Impact of microorganism on polonium volatilization

    International Nuclear Information System (INIS)

    Momoshima, N.; Ishida, A.; Fukuda, A.; Yoshinaga, C.

    2007-01-01

    Volatilization of polonium by microorganisms, Chromobacterium violaceum, Escherichia coli and Bacillus subtilis was examined for pure cultures in LB medium at 30 deg C, showing relative Po emission intensity 100, 10 and 1, respectively. Chromobacterium violaceum pre-cultured in LB medium without Po and suspended in water with Po showed high Po volatilization in spite of poor nutriment condition. Antibiotics inhibit volatilization of Po and cultivation at low temperature greatly reduced volatilization. The results strongly support the biological effects on Po volatilization. (author)

  18. Intake of lead210 and polonium210 by inhalation of atmospheric air and cigarette smoke

    International Nuclear Information System (INIS)

    Brigido Flores, Osvaldo; Montalvan Estrada, Adelmo; Alonso Hernandez, Carlos; Tomas Zerquera, Juan

    2004-01-01

    The electroplating of polonium at two different times onto copper disks and further measurement of alpha activity was the method used for 210Po determination in atmospheric air and tobacco products. The Polonium daughter is used to determine both the 210 Pb and 210 Po using the Bateman equations for radioactive growth and decay. The values of 210 Pb and 210 Po measured in the ground-level air reported average concentrations of 0.65 and 0.06 mBq.m-3, respectively. A cigarette contains an average activity of 13.0 mBq of 210 Pb and 10.4 mBq of 210 Po for different Cuban cigarette brands. The weighted-average annual effective dose estimated due to inhalation of these nuclides was computed to be 38 Sv, corresponding to the 26.8% of the total effective dose received by intake of 210 Pb and 210 Po in area of natural radioactive background

  19. Exposure of cuban population due to dietary intake of lead 210 and polonium 210

    International Nuclear Information System (INIS)

    Brigido Flores, O.; Barreras Caballero, A.; Montalvan Estrada, A.; Alonso Hernandez, C.; Tomas Zerquera, J.

    2000-01-01

    Data are presented on the concentrations of 210Pb and 210Po in potable water and different food items collected from various locations in Cuba. The electroplating of polonium at two different times onto copper disks and further measurement of alpha activity was the method used for 210Po determination in foods and water. The Polonium daughter is used to determine both the 210Pb and 210Po using the Bateman equations for radioactive growth and decay. The average 210Pb and 210Po concentration in potable water was 3 and 2 mBq.l-1, respectively and concentration in total diet averaged 47.7 mBq.kg-1 for 210Pb and 131.9 mBq.kg-1 for 210Po. The annual effective dose estimated due to ingestion of these nuclides contained in foods and potable water reported a value of 77.7 [Sv corresponding the 95.7 % to the food consuming

  20. Polonium-210 in Bombay diet

    International Nuclear Information System (INIS)

    Khandekar, R.N.

    1977-01-01

    The results of the measurement of concentration levels of 210 Po in most of the common foods in the typical Bombay diet are given and estimates provided of the total daily intake of 210 Po by an individual of Bombay city. (U.K.)

  1. Polonium-210 in Bombay diet

    Energy Technology Data Exchange (ETDEWEB)

    Khandekar, R N [Bhabha Atomic Research Centre, Bombay (India). Air Monitoring Section

    1977-08-01

    The results of the measurement of concentration levels of /sup 210/Po in most of the common foods in the typical Bombay diet are given and estimates provided of the total daily intake of /sup 210/Po by an individual of Bombay city.

  2. Polonium 210 content in foodstuffs produced in Bulgaria

    International Nuclear Information System (INIS)

    Keslev, D.; Novakova, E.; Boyadzhiev, A.; Kerteva, A.

    1975-01-01

    A study of the content of polonium-210 in a variety of foodstuffs produced in Bulgaria in 1970 revealed peak radionuclide concentration in wheat - 6.7 pCi/kg, followed by prunes - 2.2 pCi/kg, cabbage - 1.86 pCi/kg, peppers - 1.64 pCi/kg. The content of polonium-210 in onions, meat and potatoes was low (0.5, 0.8 and 0.9 pCi/kg accordingly). All other food products studied - milk, bread, beans, eggs, tomatoes, apples, pears, grapes and drinking water - appeared to have approximately equal polonium-210 concentration - from 1.21 to 1.35 pCi/kg. The daily intake of polonium-210 with food and water amounted accordingly to 1.61, 1.79 and 2.08 pCi/kg in preschool children, in school children and in senile individuals. The major part (68 - 82 per cent) of incorporated polonium-210 was eliminated with the stools. In all age groups the amount of polonium-210 removed daily from the body with the excreta corresponded to the intake, i.e. the balance of polonium-210 was in a state of equilibrium. The age factor in all three groups exerted no effect on the radionuclide intake and elimination from the body. (Ch.K.)

  3. The Litvinenko polonium-210 case - German experiences

    International Nuclear Information System (INIS)

    Kirchner, Gerald; Kroeger, Emily A.

    2008-01-01

    This paper brings together the measurement results taken and the lessons learned by the German Federal Office for Radiation Protection during the polonium-210 incident in Hamburg in late 2006. The incident was pivotal in confirming the importance of the defence against nuclear hazards in Germany and for highlighting the role of communication in the success of a deployment. The background of the case is reviewed and an overview of the German defence against nuclear hazards is given. The various measurement tasks, both at the scene and in the laboratory, and their results are summarized along with the communication challenges experienced. The main conclusions are that the traces of polonium-210 found at the sites were of little radiological consequence and the German defence against nuclear hazards in Germany delivered an excellent and measured response to the incident. However, communication challenges still exist and communication with the public and the emergency responders has to be given high priority during future deployments in order to ensure their success. (author)

  4. Tolerance

    DEFF Research Database (Denmark)

    Tønder, Lars

    is linked to a different set of circumstances than the ones suggested by existing models in contemporary democratic theory. Reorienting the discussion of tolerance, the book raises the question of how to disclose new possibilities within our given context of affect and perception. Once we move away from......Tolerance: A Sensorial Orientation to Politics is an experiment in re-orientation. The book is based on the wager that tolerance exceeds the more prevalent images of self-restraint and repressive benevolence because neither precludes the possibility of a more “active tolerance” motivated...... by the desire to experiment and to become otherwise. The objective is to discuss what gets lost, conceptually as well as politically, when we neglect the subsistence of active tolerance within other practices of tolerance, and to develop a theory of active tolerance in which tolerance's mobilizing character...

  5. Tree-growth analyses to estimate tree species' drought tolerance.

    Science.gov (United States)

    Eilmann, Britta; Rigling, Andreas

    2012-02-01

    Climate change is challenging forestry management and practices. Among other things, tree species with the ability to cope with more extreme climate conditions have to be identified. However, while environmental factors may severely limit tree growth or even cause tree death, assessing a tree species' potential for surviving future aggravated environmental conditions is rather demanding. The aim of this study was to find a tree-ring-based method suitable for identifying very drought-tolerant species, particularly potential substitute species for Scots pine (Pinus sylvestris L.) in Valais. In this inner-Alpine valley, Scots pine used to be the dominating species for dry forests, but today it suffers from high drought-induced mortality. We investigate the growth response of two native tree species, Scots pine and European larch (Larix decidua Mill.), and two non-native species, black pine (Pinus nigra Arnold) and Douglas fir (Pseudotsuga menziesii Mirb. var. menziesii), to drought. This involved analysing how the radial increment of these species responded to increasing water shortage (abandonment of irrigation) and to increasingly frequent drought years. Black pine and Douglas fir are able to cope with drought better than Scots pine and larch, as they show relatively high radial growth even after irrigation has been stopped and a plastic growth response to drought years. European larch does not seem to be able to cope with these dry conditions as it lacks the ability to recover from drought years. The analysis of trees' short-term response to extreme climate events seems to be the most promising and suitable method for detecting how tolerant a tree species is towards drought. However, combining all the methods used in this study provides a complete picture of how water shortage could limit species.

  6. Tolerance

    DEFF Research Database (Denmark)

    Tønder, Lars

    Tolerance: A Sensorial Orientation to Politics is an experiment in re-orientation. The book is based on the wager that tolerance exceeds the more prevalent images of self-restraint and repressive benevolence because neither precludes the possibility of a more “active tolerance” motivated by the d...... these alternatives by returning to the notion of tolerance as the endurance of pain, linking this notion to exemplars and theories relevant to the politics of multiculturalism, religious freedom, and free speech....

  7. Hair as an indicator of the body content of polonium in humans: preliminary results from study of five male volunteers

    International Nuclear Information System (INIS)

    Rääf, C.L.; Holstein, H.; Holm, E.; Roos, P.

    2015-01-01

    The radionuclide 210 Po is of importance from a radiation protection view and has properties that cause special problems when attempting to determine the body content in humans. Estimates have traditionally been made from either urine and/or fecal samples, which require a time-consuming radiochemical preparation before alpha spectrometric determination. In order to find a more simple and less labor intensive method hair has been used as a bioindicator and investigated in this study. The relationship between intake and excretion in hair has been estimated in five volunteers who ingested radioactive polonium ( 209 Po as a bio-tracer for 210 Po) in well determined quantities. Four of the volunteers were given 5–10 Bq 209 Po in a single intake (acute intake) and one volunteer has ingested a daily intake of 58.7 mBq 209 Po for a period of 180 d. Human hair was found to reflect the daily clearance of ingested polonium peaking at 0.001–0.01% d −1 of the ingested amount, thereafter decreasing mono-exponentially, corresponding to a biological half-time of 10–20 days. For the case of protracted intake a mono-exponential build-up was observed with a half-time of 40 ± 5 d. In addition, after cessation of intake, a short-term component (74%) with a biological half-time of 16 ± 4 d, and a long-term component (26%) with a half-time of 93 ± 53 d were observed. It is concluded that hair can be used to detect not only the amount of ingested polonium but also whether the intake was protracted or acute. - Highlights: • After single intakes polonium is excreted in hair with biological half-times (range 15–30 days). • Polonium concentration vs position in hair strand reflects the intake history of subject. • For acute intakes peak hair concentration or daily excretion can be related to the amount of intake. • Protracted intakes of polonium result in an increase in Po concentration in hair, reaching equilibrium after 180 days. • Bi-exponential decay of

  8. Cooperative Fault Tolerant Tracking Control for Multiagent Systems: An Intermediate Estimator-Based Approach.

    Science.gov (United States)

    Zhu, Jun-Wei; Yang, Guang-Hong; Zhang, Wen-An; Yu, Li

    2017-10-17

    This paper studies the observer based fault tolerant tracking control problem for linear multiagent systems with multiple faults and mismatched disturbances. A novel distributed intermediate estimator based fault tolerant tracking protocol is presented. The leader's input is nonzero and unavailable to the followers. By applying a projection technique, the mismatched disturbances are separated into matched and unmatched components. For each node, a tracking error system is established, for which an intermediate estimator driven by the relative output measurements is constructed to estimate the sensor faults and a combined signal of the leader's input, process faults, and matched disturbance component. Based on the estimation, a fault tolerant tracking protocol is designed to eliminate the effects of the combined signal. Besides, the effect of unmatched disturbance component can be attenuated by directly adjusting some specified parameters. Finally, a simulation example of aircraft demonstrates the effectiveness of the designed tracking protocol.This paper studies the observer based fault tolerant tracking control problem for linear multiagent systems with multiple faults and mismatched disturbances. A novel distributed intermediate estimator based fault tolerant tracking protocol is presented. The leader's input is nonzero and unavailable to the followers. By applying a projection technique, the mismatched disturbances are separated into matched and unmatched components. For each node, a tracking error system is established, for which an intermediate estimator driven by the relative output measurements is constructed to estimate the sensor faults and a combined signal of the leader's input, process faults, and matched disturbance component. Based on the estimation, a fault tolerant tracking protocol is designed to eliminate the effects of the combined signal. Besides, the effect of unmatched disturbance component can be attenuated by directly adjusting some

  9. Measurement of polonium activity in Indian tobacco

    Energy Technology Data Exchange (ETDEWEB)

    Singh, D R; Nilekani, S R [Bhabha Atomic Research Centre, Bombay (India). Div. of Radiation Protection

    1976-10-01

    To assess the probable induction of lung cancer due to /sup 210/Po in Indian tobacco, 116 samples of tobacco drawn from seven brands of cigarettes, cigars, cheroots and local beedi fillings were assayed. The results are tabulated and show an average /sup 210/Po content for cigarettes varying from 0.07 to 0.10 pCi/g except for one brand which had a higher value of 0.152 pCi/g. Large cigars were shown to have less polonium content compared to other tobacco products such as cheroot, beedi fillings and small cigars. From the data obtained the lung burden of a smoker of Indian cigarettes has been calculated to be 23.6 mrad/day which is between 3 and 6 times higher than that due to natural background of radon and thoron in the atmosphere.

  10. Polonium in cigarette smoke and radiation exposure of lungs

    International Nuclear Information System (INIS)

    Carvalho, F.P.; Oliveira, J.M.

    2006-01-01

    210 Po was analysed in three common brands of cigarettes produced in Portugal. The analyses of polonium were performed using 209 Po as an internal isotopic tracer. Samples were dissolved with acids, polonium plated on a silver disc and measured by alpha spectrometry using silicon surface barrier detectors. The analyses were carried out on the unburned tobacco contained in the cigarettes, on the ashes of smoked cigarettes and on the mainstream smoke inhaled by the smoker. 210 Po in the tobacco display concentrations ranging from 3 to 37 mBq/g, depending upon the cigarette brand. The 210 Po remaining in the solid residue of a smoked cigarette varied between 0.3 to 4.9 mBq per cigarette, and the 210 Po in the inhaled smoke from one cigarette varied from 2.6 to 28.9 mBq. In all brands of cigarettes tested, about 50 % of the 210 Po content is not inhaled by the smoker and it is released into the atmosphere. Part of it may be inhaled by passive smokers. Depending upon the commercial brand and upon the presence or absence of a filter in the cigarette, 5 to 37 % of the 210 Po in the cigarette can be inhaled by the smoker. Taking into account the average 210 Po and 210 Pb in surface air, the smoker of one pack of twenty cigarettes per day may inhale 50 times more 210 Po than a non smoker. The average absorption of 210 Po into the blood taking all pathways into account is 0.39 Bq d -1 . This includes, namely, the ingestion of water and beverages, the ingestion of food, the inhalation of air and cigarette smoke. Cigarette smoke contributes with 1.5 % to this rate of 210 Po absorption into the blood and, after circulating in all organs, gives rise to a whole body radiation dose in the same proportion. However, in the smoker the deposition of 210 Po in the lungs is much more elevated than normal and may originate an enhanced radiation exposure of this organ. Estimated dose to the lungs is presented and radiobiological effects of cigarette smoking are discussed. (author)

  11. Estimators of the Relations of Equivalence, Tolerance and Preference Based on Pairwise Comparisons with Random Errors

    Directory of Open Access Journals (Sweden)

    Leszek Klukowski

    2012-01-01

    Full Text Available This paper presents a review of results of the author in the area of estimation of the relations of equivalence, tolerance and preference within a finite set based on multiple, independent (in a stochastic way pairwise comparisons with random errors, in binary and multivalent forms. These estimators require weaker assumptions than those used in the literature on the subject. Estimates of the relations are obtained based on solutions to problems from discrete optimization. They allow application of both types of comparisons - binary and multivalent (this fact relates to the tolerance and preference relations. The estimates can be verified in a statistical way; in particular, it is possible to verify the type of the relation. The estimates have been applied by the author to problems regarding forecasting, financial engineering and bio-cybernetics. (original abstract

  12. Extreme accumulations of natural polonium-210 in certain marine organisms

    International Nuclear Information System (INIS)

    Folsom, T.R.; Wong, K.M.; Hodge, V.F.

    1972-01-01

    Concentration levels of polonium-210 reported for sea water are reviewed, and activities accumulated by various marine plant and animal species are discussed. Special mention is made of detailed studies of one giant algae upon whose outer surfaces intense accumulations of polonium have been discovered recently. Some concentrations found in two organisms intimate with algae, the abalones and the sea hares, are reported. Concentrations are listed pertaining to organisms selected from the open ocean in order to show that intense polonium concentrations are not restricted to organisms living near the continents where precursors of polonium originate. A brief discussion of conditions on one of the marine mammals, the dolphin, next is made. Then comments are made upon a benthic species (the sable fish) that prefers to live close to the deep sea floor, presumably so as to eat detritus. They also eat many of the smaller organisms that compete for the natural deep sea fallout of food, and many of these live in close contact with the muds and clays of the sea floor that are rich in radium. Some of the behavior and anatomical features and polonium-210 distribution in one of the most interesting and valuable of fishes, the North Pacific albacore (Thunnus alalunga) is described. This species has been used previously to tell us something about nuclear fallout distributions in the North Pacific Ocean during the past decade and repeatedly has directed attention to features of this ocean that might hardly be detected otherwise. (U.S.)

  13. Application of Joint Parameter Identification and State Estimation to a Fault-Tolerant Robot System

    DEFF Research Database (Denmark)

    Sun, Zhen; Yang, Zhenyu

    2011-01-01

    The joint parameter identification and state estimation technique is applied to develop a fault-tolerant space robot system. The potential faults in the considered system are abrupt parametric faults, which indicate that some system parameters will immediately deviate from their nominal values...

  14. Real-time fault-tolerant moving horizon air data estimation for the RECONFIGURE benchmark

    NARCIS (Netherlands)

    Wan, Y.; Keviczky, T.

    2018-01-01

    This paper proposes a real-time fault-tolerant estimation approach for combined sensor fault diagnosis and air data reconstruction. Due to simultaneous influence of winds and latent faults on monitored sensors, it is challenging to address the tradeoff between robustness to wind disturbances and

  15. Method for evaluation of doses from ingestion of polonium, bismuth and lead as natural radioactive material(NORM)

    International Nuclear Information System (INIS)

    Pena, Vanessa; Puerta, Anselmo; Morales, Javier

    2013-01-01

    In this work was carried out an evaluation of dose from ingestion of radioactive daughters of radon (lead, bismuth and polonium), taking into account ages from three months up to adult men, using the new model of the human alimentary tract HATM and methodology of calculating doses proposed by the ICRP publication 103, which allows the estimation of dose based on the concentration of the radionuclide present in the diet or in the water of consumption

  16. Systematics of even-a polonium isotopes

    International Nuclear Information System (INIS)

    Younes, W.; Cizewski, J.A.; Bernstein, L.A.

    1995-01-01

    Polonium nuclei, with two valence protons, provide fertile ground for the study of the onset of collectivity: from the textbook two-particle levels of 210 Po to the phonon-like multiplets of 196 Po. In their earlier work the authors described the low-lying structure of even-A Po nuclei down to 196 Po as two protons interacting via a surface-δ interaction and adiabatically coupled to a vibrating core. However, this particle-core model (PCM) fails to adequately describe the recently measured level scheme of 194 Po. Also because it assumes a pre-existing vibrational core, this model does not help to understand the single particle contributions to the collective motion. Therefore, the authors have also studied the Po systematics using a more microscopic model: the quasi-particle random phase approximation (QRPA). They will present a phenomenological analysis of the rapidity of the onset of collectivity for the Po isotopes as well as results of both PCM and QRPA calculations. The microscopic nature of the collectivity for the even-A Po isotopes will be discussed

  17. Behaviour of polonium-210 during anode slimes processing

    International Nuclear Information System (INIS)

    Brown, S. A.

    1998-01-01

    Refinery slimes produced during the electrorefining of copper anodes often contain recoverable quantities of gold, silver and the platinum group metals, platinum and palladium. The treatment process selected to recover precious metals from the slimes depends on the concentration of other impurities. Polonium-210 will be present in the refinery slimes when uranium-bearing minerals (e.g. uraninite) are associated with the copper mineralogy. The production of pure precious metals from copper anode slimes containing polonium-210 involves a variety of steps including impurity removal, smelting to produce a dore metal and then refining. Gold and silver are recovered by electrorefining processes. Platinum group metals accumulate in the gold electrolyte and are recovered by precipitation. To ensure that specifications are met in the final products, it is necessary to identify and closely monitor where the impurities, including polonium-210, are partitioning during processing. Although measurement of polonium-210 activity using alpha spectrometry identifies relative amounts of the radionuclide in the various streams, it does not give any indication of the form it may be in. By studying the chemistry and deportment of its neighbours in the periodic table (Pb,Bi,Se and Te) it may be possible to make some conclusions regarding polonium-210 behaviour. Examination of the solid phases produced during anode slimes treatment were carried out using X-ray diffraction (XRD) and scanning electron microscopy (SEM). Elemental analyses of solid and liquor streams were carried out using Inductively Coupled Plasma Atomic Emission Spectroscopy (ICPAES). This paper attempts to develop a relationship between the behaviour of polonium-210 and other impurities during precious metals recovery based on the results of these studies

  18. Behaviour of polonium-210 during anode slimes processing

    International Nuclear Information System (INIS)

    Brown, S.A.

    1998-01-01

    Refinery slimes produced during the electrorefining of copper anodes often contain recoverable quantities of gold, silver and the platinum group metals, platinum and palladium. The treatment process selected to recover precious metals from the slimes depends on the concentration of other impurities. Polonium 210 will be present in the refinery slimes when uranium-bearing minerals (eg. uraninite) are associated with the copper mineralogy. The production of pure precious metals from copper anode slimes containing polonium-210 involves a variety of steps including impurity removal smelting to produce a dore metal and then refining. Gold and silver are recovered by electrorefining processes. Platinum group metals accumulate in the gold electrolyte and are recovered by precipitation To ensure that specifications are met in the final products, it is necessary to identify and closely monitor where the impurities, including polonium-210, are partitioning during processing. Although measurement of polonium-210 activity using alpha spectrometry identifies relative amounts of the radionuclide in the various streams, it does not give any indication of the form it may be in. By studying the chemistry and deportment of its neighbours in the periodic table (Pb, Bi, Se and Te) it may be possible to make some conclusions regarding polonium-210 behaviour. Examination of the solid phases produced during anode slimes treatment were carried out using X-ray diffraction (XRD) and scanning electron microscopy (SEM). Elemental analyses of solid and liquor streams were carried out using Inductively Coupled Plasma Atomic Emission Spectroscopy (ICPAES). This paper attempts to develop a relationship between the behaviour of polonium-210 and other impurities during precious metals recovery based on the results of these studies. (author). 5 refs., 4 tabs

  19. Bioaccumulation of polonium ({sup 210}Po) and uranium ({sup 234}U, {sup 238}U) in plants around phosphogypsum waste heap in Wislinka (northern Poland)

    Energy Technology Data Exchange (ETDEWEB)

    Borylo, A.; Skwarzec, B. [Gdansk Univ. (Poland). Faculty of Chemistry

    2011-07-01

    In the study the activities of polonium {sup 210}Po and uranium {sup 234}U, {sup 238}U in plants, collected near phosphogypsum waste heap in Wis'linka (northern Poland), were determined by using the alpha spectrometry. The obtained results revealed that the concentrations of {sup 210}Po, {sup 234}U, and {sup 238}U in the analyzed plants were differentiated. In the analyzed flora organisms the highest amounts of polonium and uranium were found in ruderal plant samples as well as willow samples (Salix viminalis) from protection zone of phosphogypsum waste heap. The concentrations of {sup 210}Po, {sup 234}U and {sup 238}U in the analyzed plants were higher in roots than in green parts of plants. The higher concentrations of {sup 210}Po and {sup 238}U radionuclides were estimated for hydrophyte (common sedge Carex nigra Reichard), the favourite habitat of which is particularly wet meadow and for plants collected in the vicinity of phosphogypsum waste heap. The major source of polonium and uranium in analyzed plants is root system. The values of {sup 234}U/ {sup 238}U activity ratio in all analyzed plants are closed to one, what indicated that source of uranium in analyzed plants is phosphogypsum. The highest uranium and polonium concentrations were characterized for plants, which are covered with tomentose. The comparability polonium and uranium contents were confirmed in edible plants, but higher accumulation was determined in ripe species than immature species of vegetables. The higher polonium and uranium concentrations were noticed in green parts of plant, the lower in roots. Polonium concentration in cultivated plants samples was not species diverse. Therefore, the significant source of polonium and uranium in analyzed plants is wet and dry atmospheric falls gathering the soil and air dust from phosphogypsum waste dump. The maximum {sup 210}Po and {sup 238}U radionuclides concentrations were found in green parts of red beet (Beta vulgaris esculenta), the

  20. Levels of lead-210 (210Pb) and polonium 210 (210Po) in Cuban Tobacco products

    International Nuclear Information System (INIS)

    Brigido, F.O.; Barrerras Caballero, A.; Alvarez Rodriguez, D.; Montalvan Estrada, A.

    1999-01-01

    The release of 210Po in tobacco smoke and the radiation dose for man have been studied because of the high incidence of lung cancer among smoker. The electroplating of polonium at two different times onto copper disks and further measurement of alpha activity was the meted used for 210 Po determination in tobacco products. The Polonium daughter is used to determine both the 210Pb and 210Po using the Baseman equations for radioactive growth and decay. A cigarette contains between 10.6 and 14.7 mBq of 210Pb with an average activity of 13.0 mBq and between 8.5 and 12.3 mBq of 210Po with an average activity of 10.4 mBq for different Cuban cigarette brands. For a person smoking a pack of 20 cigarettes a day, the values of intakes estimated range from 32 to 44 mBq for 210Pb and from 34 to 49 mBq for 210 Po with an average daily intake of 39 mBq for 210 Pb and 42 mBq for 210Po. The annual effective dose estimated due to inhalation of these nuclides contained in cigarette smoke shows a value of 66[Sv and was in correspondence with world-wide range dose, 46 - 90 mSv.year 1 - for tobacco product consumption

  1. Structural equation models to estimate risk of infection and tolerance to bovine mastitis.

    Science.gov (United States)

    Detilleux, Johann; Theron, Léonard; Duprez, Jean-Noël; Reding, Edouard; Humblet, Marie-France; Planchon, Viviane; Delfosse, Camille; Bertozzi, Carlo; Mainil, Jacques; Hanzen, Christian

    2013-03-06

    One method to improve durably animal welfare is to select, as reproducers, animals with the highest ability to resist or tolerate infection. To do so, it is necessary to distinguish direct and indirect mechanisms of resistance and tolerance because selection on these traits is believed to have different epidemiological and evolutionary consequences. We propose structural equation models with latent variables (1) to quantify the latent risk of infection and to identify, among the many potential mediators of infection, the few ones that influence it significantly and (2) to estimate direct and indirect levels of tolerance of animals infected naturally with pathogens. We applied the method to two surveys of bovine mastitis in the Walloon region of Belgium, in which we recorded herd management practices, mastitis frequency, and results of bacteriological analyses of milk samples. Structural equation models suggested that, among more than 35 surveyed herd characteristics, only nine (age, addition of urea in the rations, treatment of subclinical mastitis, presence of dirty liner, cows with hyperkeratotic teats, machine stripping, pre- and post-milking teat disinfection, and housing of milking cows in cubicles) were directly and significantly related to a latent measure of bovine mastitis, and that treatment of subclinical mastitis was involved in the pathway between post-milking teat disinfection and latent mastitis. These models also allowed the separation of direct and indirect effects of bacterial infection on milk productivity. Results suggested that infected cows were tolerant but not resistant to mastitis pathogens. We revealed the advantages of structural equation models, compared to classical models, for dissecting measurements of resistance and tolerance to infectious diseases, here bovine mastitis. Using our method, we identified nine major risk factors that were directly associated with an increased risk of mastitis and suggested that cows were tolerant but

  2. Marie Sklodowska-Curie, polonium, radium and radiochemistry

    International Nuclear Information System (INIS)

    Guillaumont, R.

    2011-01-01

    In this work, the author describes how the methodology developed by Marie Curie in discovering polonium and radium has contributed to greater scientific discoveries and how these discoveries have played a great part in the development of science in general and have particularly enriched chemistry. (O.M.)

  3. Polonium in cigarette smoke and radiation exposure of lungs

    International Nuclear Information System (INIS)

    Carvalho, F.P.; Oliveira, J.M.

    2006-01-01

    Polonium ( 210 Po), the most volatile of naturally-occurring radionuclides in plants, was analysed in three common brands of cigarettes produced in Portugal. The analyses were carried out on the unburned tobacco contained in cigarettes, on the ashes and butts of smoked cigarettes and on the mainstream smoke. 210 Po in tobacco displays concentrations ranging from 3 to 37 mBq g -1 , depending upon the cigarette brand. The 210 Po activity remaining in the solid residue of a smoked cigarette varied from 0.3 to 4.9 mBq per cigarette, and the 210 Po in the inhaled smoke varied from 2.6 to 28.9 mBq. In all brands of cigarettes tested, a large fraction of the 210 Po content is not inhaled by the smoker and it is released into the atmosphere. Part of it may be inhaled by passive smokers. Depending upon the commercial brand and upon the presence or absence of a filter in the cigarette, 5 to 37 % of the 210 Po in the cigarette can be inhaled by the smoker. Taking into account the average 210 Po in surface air, the smoker of one pack of twenty cigarettes per day may inhale 50 times more 210 Po than a non smoker. Cigarette smoke contributes with 1.5 % to the daily rate of 210 Po absorption into the blood, 0.39 Bq d -1 , and, after systemic circulation it gives rise to a whole body radiation dose in the same proportion. However, in the smoker the deposition of 210 Po in the lungs is much more elevated than normal and may originate an enhanced radiation exposure. Estimated dose to the lungs is presented and radiobiological effects of cigarette smoke are discussed. (author)

  4. Dosimetric consideration of polonium-210 for Tiruchirappalli public

    International Nuclear Information System (INIS)

    Shaheed, K.; Somasundaram, S.S.N.; Shahul Hameed, P.

    1997-01-01

    This paper deals with the committed effective dose equivalent from polonium-210 to the public of Tiruchirappalli district in south India on consumption of cereals, vegetables and animal food. It is demonstrated that the activity of 210 Po is non-uniformly distributed between cereals, vegetables and animal food. Among cereals, the green gram recorded a higher activity of 210 Po (0.62 Bq.kg -1 ) than the others tested. The study also recorded a relatively enhanced activity in raw rice (0.90 Bq.kg -1 ) than in boiled rice (0.03 Bq.kg -1 ). Among vegetables, the tubers accumulated more 210 Po than the shoot growing vegetables. The muscle of prawn (Macrobrachium rosenbergii) recorded the highest level of 210 Po activity (13.9 Bq.kg -1 ) among the animal food. With reference to dosimetry, the animal food was identified to contribute higher radiation dose (0.38-29.5 μSv.y -1 ) than the cereals (0.05 - 1.9 μSv.y -1 ) and vegetables (0.05 - 1.9 μSv.y -1 ). Among animal food, the fish contributed a substantial level of α radiation dose to man. Though activity in raw rice was higher than the activity in boiled rice, the dose delivered from raw rice was substantially low since the average consumption of this rice represents only 7 kg.y -1 when compared to the consumption of boiled rice (108 kg.y -1 ). From the dose estimates made, it was evident that the total dose received by the general public (2.7 μSv.y -1 ) from 210 Po was well below the dose limit of 1mSv.y -1 . (author)

  5. Evaluation of sample pretreatment methods for analysis of polonium isotopes in herbal medicines

    International Nuclear Information System (INIS)

    Sreejith, Sathyapriya R.; Nair, Madhu G.; Rao, D.D.

    2014-01-01

    Herbal infusions like ayurvedic aristas are widely consumed by Indian population for good health. With increasing awareness about radiological assessment, an effort was made to assess the radioactivity concentration of naturally occurring radionuclides in herbal medicines. 210 Po is an important alpha particle emitter contributing to internal dose to man from ingestion. Though 210 Po can be spontaneously deposited on silver disk for alpha spectrometric measurements with less radiochemical step, great care has to be taken during the sample pretreatment step owing to the high volatility of polonium even at low temperatures. Aim of the study was to evaluate an appropriate sample pretreatment method for estimation of polonium in herbal medicines. 209 Po was used for radiochemical yield calculation. Conventional open vessel wet ashing, physical evaporation, freeze-drying and microwave digestion in a Teflon vessel were examined. The recovery ranged between 9 and 79%. The lowest recovery was obtained for the samples that were processed by open vessel digestion without any volume reduction. The recoveries were comparable for those samples that were freeze dried and subjected to HNO 3 + HClO 4 + H 2 O 2 + HF acid digestion and microwave digested samples. 210 Po concentration in the samples ranged from 11.3 to 39.6 mBq/L

  6. Characteristics of polonium contamination from neutral irradiated lead-bismuth eutectic

    International Nuclear Information System (INIS)

    Miura, T.; Obara, T.; Sekimoto, H.

    2004-01-01

    After neutron capture, bismuth-209 changes to polonium-210 that emits α-particles. Lead-Bismuth eutectic (LBE) in reactor system contaminates the system by polonium. We analyzed adsorbed materials from melted LBE on quartz glass plate. Lead, bismuth and their oxides were confirmed in adsorbed materials. And, we evaluated the baking method in vacuum for removal of polonium and adsorbed materials on quartz glass plate. It was evaluated that it is possible to remove almost all the polonium from the quartz glass plate by baking at temperature more than 300 C. degrees. Unfolding method was applied to calculate polonium distribution in LBE ingot. From measured α-particle pulse height distribution, the polonium distribution in depth of LBE ingot was calculated using quadratic programming code, where response functions are calculated by Monte Carlo method. (authors)

  7. Global error estimation based on the tolerance proportionality for some adaptive Runge-Kutta codes

    Science.gov (United States)

    Calvo, M.; González-Pinto, S.; Montijano, J. I.

    2008-09-01

    Modern codes for the numerical solution of Initial Value Problems (IVPs) in ODEs are based in adaptive methods that, for a user supplied tolerance [delta], attempt to advance the integration selecting the size of each step so that some measure of the local error is [similar, equals][delta]. Although this policy does not ensure that the global errors are under the prescribed tolerance, after the early studies of Stetter [Considerations concerning a theory for ODE-solvers, in: R. Burlisch, R.D. Grigorieff, J. Schröder (Eds.), Numerical Treatment of Differential Equations, Proceedings of Oberwolfach, 1976, Lecture Notes in Mathematics, vol. 631, Springer, Berlin, 1978, pp. 188-200; Tolerance proportionality in ODE codes, in: R. März (Ed.), Proceedings of the Second Conference on Numerical Treatment of Ordinary Differential Equations, Humbold University, Berlin, 1980, pp. 109-123] and the extensions of Higham [Global error versus tolerance for explicit Runge-Kutta methods, IMA J. Numer. Anal. 11 (1991) 457-480; The tolerance proportionality of adaptive ODE solvers, J. Comput. Appl. Math. 45 (1993) 227-236; The reliability of standard local error control algorithms for initial value ordinary differential equations, in: Proceedings: The Quality of Numerical Software: Assessment and Enhancement, IFIP Series, Springer, Berlin, 1997], it has been proved that in many existing explicit Runge-Kutta codes the global errors behave asymptotically as some rational power of [delta]. This step-size policy, for a given IVP, determines at each grid point tn a new step-size hn+1=h(tn;[delta]) so that h(t;[delta]) is a continuous function of t. In this paper a study of the tolerance proportionality property under a discontinuous step-size policy that does not allow to change the size of the step if the step-size ratio between two consecutive steps is close to unity is carried out. This theory is applied to obtain global error estimations in a few problems that have been solved with

  8. Polonium-210 and lead-210 contamination of plants

    Energy Technology Data Exchange (ETDEWEB)

    Popova, O N; Taskaev, A I

    1977-01-01

    A model experiment with a water culture of barley grown in closed vessels, with an increased content of radon-222 in the air, has demonstrated an intensive contamination of the overground part and roots of the plant with polonium-210 and lead-210. Roots having no overground part were affected by radionuclides in a similar way as those of intact plants. Contamination was minimal in the plants grown from soil cultures.

  9. Evolution of collective motion in light polonium nuclei

    International Nuclear Information System (INIS)

    Cizewski, J. A.

    1998-01-01

    The γ-ray spectroscopy of even- and odd-mass isotopes of polonium have been studied using arrays of Ge detectors coupled to recoil-mass analyzers, including recoil-decay tagging techniques. The level energies and B(E2) branching ratios can be reproduced by theoretical frameworks which do not explicitly include proton particle-hole excitations across the Z = 82 shell, conclusions in contrast to those deduced from alpha-decay measurements

  10. Adsorption of volatile polonium species on metals in various gas atmospheres. Pt. II. Adsorption of volatile polonium on platinum, silver and palladium

    Energy Technology Data Exchange (ETDEWEB)

    Maugeri, Emilio Andrea; Joerg Neuhausen; Dressler, Rugard; Piguet, David; Voegele, Alexander; Schumann, Dorothea [Paul Scherrer Institut (PSI), Villigen (Switzerland). Lab. for Radiochemistry; Misiak, Ryszard [The Henryk Niewodniczanski Institute of Nuclear Physics, Krakow (Poland); Eichler, Robert [Paul Scherrer Institut (PSI), Villigen (Switzerland). Lab. for Radiochemistry; Bern Univ. (Switzerland). Dept. for Chemistry and Biochemistry

    2016-07-01

    This work presents the results obtained from studying the interaction between polonium compounds formed in different atmospheres and platinum, palladium and silver surfaces obtained by thermochromatography. These results are of crucial importance for the design of cover gas filter systems for lead-bismuth eutectic (LBE)-based nuclear facilities such as accelerator driven systems (ADS). The results obtained from studying the interaction of polonium and platinum under inert atmosphere and reducing atmospheres with and without addition of moisture show that polonium is deposited at temperatures between 993 and 1221 K, with adsorption enthalpies ranging from -235 to -291 kJ mol{sup -1}, indicating a very strong adsorption of the polonium species present on platinum surfaces. The interaction between polonium and silver was investigated using purified inert, reducing and oxidizing carrier gases. Results show a deposition temperature between 867 and 990 K, with adsorption enthalpies ranging from -205 to -234 kJ mol{sup -1}. The interaction of polonium and palladium was studied in purified helium and purified hydrogen. For both conditions a deposition temperature of 1221 K was observed corresponding to an adsorption enthalpy of -340 kJ mol{sup -1}. No highly volatile polonium species was formed at any of the applied experimental conditions.

  11. Fault-tolerant embedded system design and optimization considering reliability estimation uncertainty

    International Nuclear Information System (INIS)

    Wattanapongskorn, Naruemon; Coit, David W.

    2007-01-01

    In this paper, we model embedded system design and optimization, considering component redundancy and uncertainty in the component reliability estimates. The systems being studied consist of software embedded in associated hardware components. Very often, component reliability values are not known exactly. Therefore, for reliability analysis studies and system optimization, it is meaningful to consider component reliability estimates as random variables with associated estimation uncertainty. In this new research, the system design process is formulated as a multiple-objective optimization problem to maximize an estimate of system reliability, and also, to minimize the variance of the reliability estimate. The two objectives are combined by penalizing the variance for prospective solutions. The two most common fault-tolerant embedded system architectures, N-Version Programming and Recovery Block, are considered as strategies to improve system reliability by providing system redundancy. Four distinct models are presented to demonstrate the proposed optimization techniques with or without redundancy. For many design problems, multiple functionally equivalent software versions have failure correlation even if they have been independently developed. The failure correlation may result from faults in the software specification, faults from a voting algorithm, and/or related faults from any two software versions. Our approach considers this correlation in formulating practical optimization models. Genetic algorithms with a dynamic penalty function are applied in solving this optimization problem, and reasonable and interesting results are obtained and discussed

  12. Levels of polonium-210 in the grapevine leaves in Alasehir district in Turkey

    International Nuclear Information System (INIS)

    Gurboga, G.; Aytas Oelmez, S.

    2001-01-01

    The objective of present work is the estimation of Po-210 (polonium) content in the edible grapevine leaves (Vitis viniferae, L.cv Sultana syn.) collected from Gediz plain in Western Turkey. Alasehir District in Gediz plain is one of the most important wine culture region of Turkey. Grapevine leaves are important food material for Dolma in Turkish cuisine. Dolma is a name applied to such vegetables as grapevine leaves, cabbage leaves and green peppers stuffed ground meat or spiked rice. Levels of Po-210 in the grapevine leaves had not been analyzed before in Turkey. In this study, after wet ashing of grapevine leaves, Po-210 was spontaneously plated onto a copper disc from dilute hydrochloric acid medium and deposited activity was measured. The results for Po-210 in the grapevine leaves are compared with the other foodstuff values in the literature

  13. Fundamental study of polonium contamination by neutron irradiated lead-bismuth eutectic

    International Nuclear Information System (INIS)

    Obara, T.; Miura, T.; Sekimoto, H.

    2005-01-01

    As a fundamental study of polonium contamination by neutron irradiated LBE, it was investigated to remove polonium surface contamination by baking method. The baking experiments were performed using quartz glass plates contaminated by material evaporated from neutron irradiated LBE liquid. The contaminated quartz glass plates were baked in vacuum (2 Pa) at various temperatures. The experimental results clearly show that polonium evaporated from LBE can be removed by baking samples at temperatures 300 deg. C and above. It is of note that the decrease in the weight of deposited materials baked at 300 deg. C differed from that observed at 400 deg. C or higher temperatures. At temperature of 300 deg. C, no change in weight was observed. The mass of polonium in the LBE samples was so small that no weight change could be observed by release of polonium. Thus, it might show that only the polonium among the adherent materials was removed by baking at 300 deg. C without removing other adhered material. The method is rather simple, so it is easy to apply the method for practical application. One of the expected applications may be the removal of polonium contamination in a primary loop before maintenance work of the loop. Also it shows that this method can be used to avoid the release of polonium from contaminated material, in case of an accident, by keeping the contaminated material at low temperature

  14. Estimation of probability of failure for damage-tolerant aerospace structures

    Science.gov (United States)

    Halbert, Keith

    The majority of aircraft structures are designed to be damage-tolerant such that safe operation can continue in the presence of minor damage. It is necessary to schedule inspections so that minor damage can be found and repaired. It is generally not possible to perform structural inspections prior to every flight. The scheduling is traditionally accomplished through a deterministic set of methods referred to as Damage Tolerance Analysis (DTA). DTA has proven to produce safe aircraft but does not provide estimates of the probability of failure of future flights or the probability of repair of future inspections. Without these estimates maintenance costs cannot be accurately predicted. Also, estimation of failure probabilities is now a regulatory requirement for some aircraft. The set of methods concerned with the probabilistic formulation of this problem are collectively referred to as Probabilistic Damage Tolerance Analysis (PDTA). The goal of PDTA is to control the failure probability while holding maintenance costs to a reasonable level. This work focuses specifically on PDTA for fatigue cracking of metallic aircraft structures. The growth of a crack (or cracks) must be modeled using all available data and engineering knowledge. The length of a crack can be assessed only indirectly through evidence such as non-destructive inspection results, failures or lack of failures, and the observed severity of usage of the structure. The current set of industry PDTA tools are lacking in several ways: they may in some cases yield poor estimates of failure probabilities, they cannot realistically represent the variety of possible failure and maintenance scenarios, and they do not allow for model updates which incorporate observed evidence. A PDTA modeling methodology must be flexible enough to estimate accurately the failure and repair probabilities under a variety of maintenance scenarios, and be capable of incorporating observed evidence as it becomes available. This

  15. Foliar retention, transport and leaching of polonium-210 and lead-210

    Energy Technology Data Exchange (ETDEWEB)

    Athalye, V V; Mistry, K B

    1972-01-01

    Polonium-210 and lead-210, the long-lived daughter radionuclides of gaseous radon-222, are deposited on plant surfaces under conditions of atmospheric washout. Foliar retention, transport and leaching of these radionuclides in Red Kidney beans were investigated in nutrient culture experiments. Under identical conditions, over 90 percent of foliar applied radiolead was retained by the plant while only about 30 percent of polonium was retained. Over a 48-hr period small quantities of polonium were translocated from the treated leaflet to other parts of the plant. By comparison, radiolead was totally immobilized at the site of retention. Leachability of root absorbed radiolead from bean leaves was 20-fold greater than that of polonium. The marked differences in the extent of foliar retention, translocation and leaching of polonium and radiolead could significantly affect the levels of these long-lived radionuclides attained in plants.

  16. Is the precision of human radiation tolerance estimates sufficient for radiation emergency management

    International Nuclear Information System (INIS)

    Lushbaugh, C.C.; Huebner, K.F.; Fry, S.A.; Ricks, R.C.

    1982-01-01

    Retrospective clinical evaluations of the deleterious consequences of accidental and therapeutic radiation exposures have provided working estimates of human radiation tolerance of variable accuracy. Their inaccuracy results from the fact that in accidents, where normal persons have been irradiated, doses have usually been unknown, whereas in radiotherapy, where doses are known precisely, the additivity of various diseases and cellular abnormalities upon final radiosensitivity remains largely unknown. Even so, from follow-up studies of radiation-accident victims, human radiation biology is not known to be qualitatively different from that of other animals and so the mechanisms of human radiation lethality are sufficiently understood to dictate therapeutic measures and suggest radiation dosage limits for their effectiveness for a few irradiated patients or where large populations are exposed under austere conditions. (author)

  17. The Total Deviation Index estimated by Tolerance Intervals to evaluate the concordance of measurement devices

    Directory of Open Access Journals (Sweden)

    Ascaso Carlos

    2010-04-01

    Full Text Available Abstract Background In an agreement assay, it is of interest to evaluate the degree of agreement between the different methods (devices, instruments or observers used to measure the same characteristic. We propose in this study a technical simplification for inference about the total deviation index (TDI estimate to assess agreement between two devices of normally-distributed measurements and describe its utility to evaluate inter- and intra-rater agreement if more than one reading per subject is available for each device. Methods We propose to estimate the TDI by constructing a probability interval of the difference in paired measurements between devices, and thereafter, we derive a tolerance interval (TI procedure as a natural way to make inferences about probability limit estimates. We also describe how the proposed method can be used to compute bounds of the coverage probability. Results The approach is illustrated in a real case example where the agreement between two instruments, a handle mercury sphygmomanometer device and an OMRON 711 automatic device, is assessed in a sample of 384 subjects where measures of systolic blood pressure were taken twice by each device. A simulation study procedure is implemented to evaluate and compare the accuracy of the approach to two already established methods, showing that the TI approximation produces accurate empirical confidence levels which are reasonably close to the nominal confidence level. Conclusions The method proposed is straightforward since the TDI estimate is derived directly from a probability interval of a normally-distributed variable in its original scale, without further transformations. Thereafter, a natural way of making inferences about this estimate is to derive the appropriate TI. Constructions of TI based on normal populations are implemented in most standard statistical packages, thus making it simpler for any practitioner to implement our proposal to assess agreement.

  18. Adsorption of volatile polonium and bismuth species on metals in various gas atmospheres. Pt. I. Adsorption of volatile polonium and bismuth on gold

    Energy Technology Data Exchange (ETDEWEB)

    Maugeri, Emilio Andrea; Neuhausen, Joerg; Dressler, Rugard; Piguet, David; Voegele, Alexander; Schumann, Dorothea [Paul Scherrer Institut (PSI), Villigen (Switzerland). Lab. for Radiochemistry; Eichler, Robert [Paul Scherrer Institut (PSI), Villigen (Switzerland). Lab. for Radiochemistry; Bern Univ. (Switzerland). Dept. for Chemistry and Biochemistry; Rijpstra, Kim [Ghent Univ., Zwijnaarde (Belgium). Center for Molecular Modeling (CMM); Cottenier, Stefaan [Ghent Univ., Zwijnaarde (Belgium). Center for Molecular Modeling (CMM); Ghent Univ., Zwijnaarde (Belgium). Dept. of Materials Science and Engineering

    2016-07-01

    Polonium isotopes are considered the most hazardous radionuclides produced during the operation of accelerator driven systems (ADS) when lead-bismuth eutectic (LBE) is used as the reactor coolant and as the spallation target material. In this work the use of gold surfaces for capturing polonium from the cover gas of the ADS reactor was studied by thermochromatography. The results show that gaseous monoatomic polonium, formed in dry hydrogen, is adsorbed on gold at 1058 K. Its adsorption enthalpy was calculated as -250±7 kJ mol{sup -1}, using a Monte Carlo simulation code. Highly volatile polonium species that were observed in similar experiments in fused silica columns in the presence of moisture in both inert and reducing gas were not detected in the experiments studying adsorption on gold surfaces. PoO{sub 2} is formed in both dry and moist oxygen, and its interaction with gold is characterized by transport reactions. The interaction of bismuth, present in large amounts in the atmosphere of the ADS, with gold was also evaluated. It was found that bismuth has a higher affinity for gold, compared to polonium, in an inert, reducing, and oxidizing atmosphere. This fact must be considered when using gold as a material for filtering polonium in the cover gas of ADS.

  19. Investigation of evaporation characteristics of polonium and its lighter homologues selenium and tellurium from liquid Pb-Bi-eutecticum

    CERN Document Server

    Neuhausen, J; Eichler, B

    2004-01-01

    The evaporation behaviour of polonium and its lighter homologues selenium and tellurium dissolved in liquid Pb-Bi-eutecticum (LBE) has been studied at various temperatures in the range from 482 K up to 1330 K under Ar/H2 and Ar/H2O-atmospheres using γ-ray spectroscopy. Polonium release in the temperature range of interest for technical applications is slow. Within short term (1h) experiments measurable amounts of polonium are evaporated only at temperatures above 973 K. Long term experiments reveal that a slow evaporation of polonium occurs at temperatures around 873 K resulting in a fractional polonium loss of the melt around 1% per day. Evaporation rates of selenium and tellurium are smaller than those of polonium. The presence of H2O does not enhance the evaporation within the error limits of our experiments. The thermodynamics and possible reaction pathways involved in polonium release from LBE are discussed.

  20. Distribution of polonium-210 in the human lung

    International Nuclear Information System (INIS)

    Cohen, Beverly S.; Eisenbud, Merril; Wrenn, McDonald E.; Harley, Naomi H.

    1978-01-01

    Knowledge of the distribution of 210 Po in the lungs of cigarette smokers is essential if the role of this alpha emitter in smoking related carcinogenesis is to be understood. To resolve this question the tracheobronchial tree is separated from the parenchyma and both are analyzed for 210 Po. Some polonium is cleared to the blood and systemically redistributed. Since systemic distribution should produce the same partition of the nuclide in smokers and nonsmokers, an excess found in either fraction would indicate retention of inhaled 210 Po or its grandparent 210 Pb. We will report the results of these analyses in five smokers and 5 nonsmokers. (author)

  1. The sorption of polonium, actinium and protactinium onto geological materials

    International Nuclear Information System (INIS)

    Baston, G.M.N.; Berry, J.A.; Brownsword, M.; Heath, T.G.; Ilett, D.J.; McCrohon, R.; Tweed, C.J.; Yui, M.

    1999-01-01

    This paper describes a combined experimental and modeling program of generic sorption studies to increase confidence in the performance assessment for a potential high-level radioactive waste repository in Japan. The sorption of polonium, actinium and protactinium onto geological materials has been investigated. Sorption of these radioelements onto bentonite, tuff and granodiorite from equilibrated de-ionized water was studied under reducing conditions at room temperature. In addition, the sorption of actinium and protactinium was investigated at 60 C. Thermodynamic chemical modeling was carried out to aid interpretation of the results

  2. The sorption of polonium, actinium and protactinium onto geological materials

    Energy Technology Data Exchange (ETDEWEB)

    Baston, G.M.N.; Berry, J.A.; Brownsword, M.; Heath, T.G.; Ilett, D.J.; McCrohon, R.; Tweed, C.J.; Yui, M.

    1999-07-01

    This paper describes a combined experimental and modeling program of generic sorption studies to increase confidence in the performance assessment for a potential high-level radioactive waste repository in Japan. The sorption of polonium, actinium and protactinium onto geological materials has been investigated. Sorption of these radioelements onto bentonite, tuff and granodiorite from equilibrated de-ionized water was studied under reducing conditions at room temperature. In addition, the sorption of actinium and protactinium was investigated at 60 C. Thermodynamic chemical modeling was carried out to aid interpretation of the results.

  3. Use of Genomic Estimated Breeding Values Results in Rapid Genetic Gains for Drought Tolerance in Maize

    Directory of Open Access Journals (Sweden)

    B.S. Vivek

    2017-03-01

    Full Text Available More than 80% of the 19 million ha of maize ( L. in tropical Asia is rainfed and prone to drought. The breeding methods for improving drought tolerance (DT, including genomic selection (GS, are geared to increase the frequency of favorable alleles. Two biparental populations (CIMMYT-Asia Population 1 [CAP1] and CAP2 were generated by crossing elite Asian-adapted yellow inbreds (CML470 and VL1012767 with an African white drought-tolerant line, CML444. Marker effects of polymorphic single-nucleotide polymorphisms (SNPs were determined from testcross (TC performance of F families under drought and optimal conditions. Cycle 1 (C1 was formed by recombining the top 10% of the F families based on TC data. Subsequently, (i C2[PerSe_PS] was derived by recombining those C1 plants that exhibited superior per se phenotypes (phenotype-only selection, and (ii C2[TC-GS] was derived by recombining a second set of C1 plants with high genomic estimated breeding values (GEBVs derived from TC phenotypes of F families (marker-only selection. All the generations and their top crosses to testers were evaluated under drought and optimal conditions. Per se grain yields (GYs of C2[PerSe_PS] and that of C2[TC-GS] were 23 to 39 and 31 to 53% better, respectively, than that of the corresponding F population. The C2[TC-GS] populations showed superiority of 10 to 20% over C2[PerSe-PS] of respective populations. Top crosses of C2[TC-GS] showed 4 to 43% superiority of GY over that of C2[PerSe_PS] of respective populations. Thus, GEBV-enabled selection of superior phenotypes (without the target stress resulted in rapid genetic gains for DT.

  4. Estimation of Peaking Factor Uncertainty due to Manufacturing Tolerance using Statistical Sampling Method

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Kyung Hoon; Park, Ho Jin; Lee, Chung Chan; Cho, Jin Young [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-10-15

    The purpose of this paper is to study the effect on output parameters in the lattice physics calculation due to the last input uncertainty such as manufacturing deviations from nominal value for material composition and geometric dimensions. In a nuclear design and analysis, the lattice physics calculations are usually employed to generate lattice parameters for the nodal core simulation and pin power reconstruction. These lattice parameters which consist of homogenized few-group cross-sections, assembly discontinuity factors, and form-functions can be affected by input uncertainties which arise from three different sources: 1) multi-group cross-section uncertainties, 2) the uncertainties associated with methods and modeling approximations utilized in lattice physics codes, and 3) fuel/assembly manufacturing uncertainties. In this paper, data provided by the light water reactor (LWR) uncertainty analysis in modeling (UAM) benchmark has been used as the manufacturing uncertainties. First, the effect of each input parameter has been investigated through sensitivity calculations at the fuel assembly level. Then, uncertainty in prediction of peaking factor due to the most sensitive input parameter has been estimated using the statistical sampling method, often called the brute force method. For our analysis, the two-dimensional transport lattice code DeCART2D and its ENDF/B-VII.1 based 47-group library were used to perform the lattice physics calculation. Sensitivity calculations have been performed in order to study the influence of manufacturing tolerances on the lattice parameters. The manufacturing tolerance that has the largest influence on the k-inf is the fuel density. The second most sensitive parameter is the outer clad diameter.

  5. Estimation of Subjective Mental Work Load Level with Heart Rate Variability by Tolerance to Driver's Mental Load

    Science.gov (United States)

    Yokoi, Toshiyuki; Itoh, Michimasa; Oguri, Koji

    Most of the traffic accidents have been caused by inappropriate driver's mental state. Therefore, driver monitoring is one of the most important challenges to prevent traffic accidents. Some studies for evaluating the driver's mental state while driving have been reported; however driver's mental state should be estimated in real-time in the future. This paper proposes a way to estimate quantitatively driver's mental workload using heart rate variability. It is assumed that the tolerance to driver's mental workload is different depending on the individual. Therefore, we classify people based on their individual tolerance to mental workload. Our estimation method is multiple linear regression analysis, and we compare it to NASA-TLX which is used as the evaluation method of subjective mental workload. As a result, the coefficient of correlation improved from 0.83 to 0.91, and the standard deviation of error also improved. Therefore, our proposed method demonstrated the possibility to estimate mental workload.

  6. Bioaccumulation of polonium 210Po in marine birds

    International Nuclear Information System (INIS)

    Skwarzec, B.; Fabisiak, J.

    2007-01-01

    The aim of this work was to determine the 210 Po content in marine birds which permanently or temporally live in the Polish part of the Baltic Sea. We chose 11 species of sea birds: three species permanently residing at southern Baltic Sea, four species of wintering birds and three species of migrating birds. The results show that the polonium is non-uniformly distributed in the marine birds. The highest activities of 210 Po were observed in feathers, muscles and liver and the lowest in skin and skeleton. Species of birds that eat crustaceans, molluscs, fish and plants (long-tailed duck Clangula hyemalis, white-winged scoter Melanitta fusca) accumulated more polonium than species that eat mainly fish (great cormorant Phalacrocorax carbo, common guillemot Uria aalge) or plants (tufted duck Aythya fuligula). Moreover, about 63% of the 210 Po that was located in feathers of razorbil (Alca torda) and long-tailed duck (C. hyemalis) was apparently adsorbed, suggesting an external source such as the air. It means that the adsorption of 210 Po on the feather surface may be an important transfer from air to water

  7. Estimating winter survival of winter wheat by simulations of plant frost tolerance

    NARCIS (Netherlands)

    Bergjord Olsen, A.K.; Persson, T.; Wit, de A.; Nkurunziza, L.; Sindhøj, E.; Eckersten, H.

    2018-01-01

    Based on soil temperature, snow depth and the grown cultivar's maximum attainable level of frost tolerance (LT50c), the FROSTOL model simulates development of frost tolerance (LT50) and winter damage, thereby enabling risk calculations for winter wheat survival. To explore the accuracy of this

  8. Pathways for the release of polonium from a lead-bismuth spallation target (thermochemical calculation); Verfluechtigungspfade des Poloniums aus einem Pb-Bi-Spallationstarget (Thermochemische Kalkulation)

    Energy Technology Data Exchange (ETDEWEB)

    Eichler, B.; Neuhausen, J

    2004-06-01

    An analysis of literature data for the thermochemical constants of polonium reveals considerable discrepancies in the relations of these data among each other as well as in their expected trends within the chalcogen group. This fact hinders a reliable assessment of possible reaction paths for the release of polonium from a liquid lead-bismuth spallation target. In this work an attempt is made to construct a coherent data set for the thermochemical properties of polonium and some of its compounds that are of particular importance with respect to the behaviour of polonium in a liquid Pb-Bi target. This data set is based on extrapolations using general trends throughout the periodic table and, in particular, within the chalcogen group. Consequently, no high accuracy should be attributed to the derived data set. However, the data set derived in this work is consistent with definitely known experimental data. Furthermore, it complies with the general trends of physicochemical properties within the chalcogen group. Finally, well known relations between thermochemical quantities are fulfilled by the data derived in this work. Thus, given the lack of accurate experimental data it can be regarded as best available data. Thermochemical constants of polonium hydride, lead polonide and polonium dioxide are derived based on extrapolative procedures. Furthermore, the possibility of formation of the gaseous intermetallic molecule BiPo, which has been omitted from discussion up to now, is investigated. From the derived thermochemical data the equilibrium constants of formation, release and dissociation reactions are calculated for different polonium containing species. Furthermore equilibrium constants are determined for the reaction of lead polonide and polonium dioxide with hydrogen, water vapour and the target components lead and bismuth. The most probable release pathways are discussed. From thermochemical evaluations polonium is expected to be released from liquid lead

  9. Fault-tolerant feature-based estimation of space debris rotational motion during active removal missions

    Science.gov (United States)

    Biondi, Gabriele; Mauro, Stefano; Pastorelli, Stefano; Sorli, Massimo

    2018-05-01

    One of the key functionalities required by an Active Debris Removal mission is the assessment of the target kinematics and inertial properties. Passive sensors, such as stereo cameras, are often included in the onboard instrumentation of a chaser spacecraft for capturing sequential photographs and for tracking features of the target surface. A plenty of methods, based on Kalman filtering, are available for the estimation of the target's state from feature positions; however, to guarantee the filter convergence, they typically require continuity of measurements and the capability of tracking a fixed set of pre-defined features of the object. These requirements clash with the actual tracking conditions: failures in feature detection often occur and the assumption of having some a-priori knowledge about the shape of the target could be restrictive in certain cases. The aim of the presented work is to propose a fault-tolerant alternative method for estimating the angular velocity and the relative magnitudes of the principal moments of inertia of the target. Raw data regarding the positions of the tracked features are processed to evaluate corrupted values of a 3-dimentional parameter which entirely describes the finite screw motion of the debris and which primarily is invariant on the particular set of considered features of the object. Missing values of the parameter are completely restored exploiting the typical periodicity of the rotational motion of an uncontrolled satellite: compressed sensing techniques, typically adopted for recovering images or for prognostic applications, are herein used in a completely original fashion for retrieving a kinematic signal that appears sparse in the frequency domain. Due to its invariance about the features, no assumptions are needed about the target's shape and continuity of the tracking. The obtained signal is useful for the indirect evaluation of an attitude signal that feeds an unscented Kalman filter for the estimation of

  10. A review of radio chemical analysis and estimation of 210Po in soil matrices

    Directory of Open Access Journals (Sweden)

    N.K. Sethy

    2015-10-01

    Full Text Available The naturally occurring radionuclide 210Po, arising from the uranium–radium decay series, provides a considerable contribution to the radiation exposure to humans. Polonium is analyzed for a variety of purposes, including for radiological impact assessment or as a tracer of environmental processes. Losses of polonium may occur at temperatures above 100 °C, depending on conditions, requiring particular care in sample preparation and treatment. There has been little development regarding analysis of polonium in environmental samples since 1960 as radiochemical analysis of polonium is quite straight forward due to easy of source preparation through auto-deposition on to metal surfaces. In this paper a brief review of estimation of polonium in the soil samples have given emphasis.

  11. Use of the transpiration method to study polonium evaporation from liquid lead-bismuth eutectic at high temperature

    International Nuclear Information System (INIS)

    Prieto, Borja Gonzalez; Lim, Jun; Rosseel, Kris; Bosch, Joris van den; Aerts, Alexander; Martens, Johan; Rizzi, Matthias; Neuhausen, Joerg

    2014-01-01

    Qualitative and quantitative understanding of Po volatilization under different conditions is of key importance for safety assessments of lead-bismuth eutectic (LBE) based nuclear reactors, spallation targets and accelerator driven systems. In this work we explore the possibilities of the transpiration method in combination with simple models to study the equilibrium and kinetics of Po evaporation from highly diluted solutions in lead-bismuth eutectic between 600 and 1000 C in Ar/5% H 2 and Ar. On the basis of evaporation experiments at various carrier gas flow rates, we identified the conditions of vapor saturation allowing the determination of equilibrium constants. From the limiting behavior at high flow rates, values for the maximal evaporation rate of Po from LBE were estimated. Measurements of evaporation as a function of time were consistent with the assumption that polonium dissolved in LBE obeys Henry's law. A theoretical analysis furthermore suggested that diffusion of polonium in LBE was not a rate limiting factor for evaporation under vapor saturation conditions. Newly determined values for the Henry constant of Po in LBE between 600 and 1000 C were consistent with previously derived correlations.

  12. Polonium in mainstream cigarette smoke and associated internal radiation dose

    International Nuclear Information System (INIS)

    Tiwari, M.; Rathod, T.D.; Bhangare, R.C.; Ajmal, P.Y.; Maity, S.; Sahu, S.K.; Pandit, G.G.

    2015-01-01

    210 Po activity concentrations in cigarettes tobacco, mainstream cigarette smoke (MCS), ash and post smoking filter were measured by alpha spectrometry using surface barrier detectors, following the radiochemical separation of polonium. The results of present study indicate that the average (range) activity concentration of 210 Po in cigarette tobacco were 9.77 to 15.34 mBq per cigarette. The combined annual effective doses due to internal exposure of 210 Po and 210 Pb for a smoker (considering on an average 20 cigarette a day and 50% of MCS getting deposited in respiratory tract) were found to be ranging from 0.28 to 0.40 mSv for tested brands of cigarette. (author)

  13. Structural equation models to estimate risk of infection and tolerance to bovine mastitis

    OpenAIRE

    Detilleux, Johann; Theron, Léonard; Duprez, Jean-Noël; Reding, Edouard; Humblet, Marie-France; Planchon, Viviane; Delfosse, Camille; Bertozzi, Carlo; Mainil, Jacques; Hanzen, Christian

    2013-01-01

    Background One method to improve durably animal welfare is to select, as reproducers, animals with the highest ability to resist or tolerate infection. To do so, it is necessary to distinguish direct and indirect mechanisms of resistance and tolerance because selection on these traits is believed to have different epidemiological and evolutionary consequences. Methods We propose structural equation models with latent variables (1) to quantify the latent risk of infection and to identify, amon...

  14. Radiological Dispersal Polonium-210, and Lessons for Public Health

    International Nuclear Information System (INIS)

    Whitcomb, R. C.; Miller, C. W.

    2007-01-01

    On November 23, 2006, Alexander Litvinenko died in London as a result of being poisoned with Polonium-210. Public health authorities in the United Kingdom (UK) subsequently found Polonium-210 contamination at a number of locations in and around London. UK authorities have determined that citizens of 48 countries other than the UK, including the United States, may have been exposed to this contamination. UK authorities asked the CDC to contact approximately 160 individuals who may have been exposed to Po-210. These citizens have been advised that their risk of adverse health effects is likely to be low, but, if they are concerned, they should contact their primary health care provider. In turn, physicians are referred to state and local public health departments or CDC for further information on Po-210, including where they can seek testing of 24 hour urine samples for Po-210, if desired. CDC posted guidance for members of the public and physicians on its web site, and it responded to numerous inquiries from national media. Working with our UK colleagues, CDC developed guidelines for judging when a measurement of Po-210 in urine was or was not a level of concern. Because the death of Mr. Litvinenko is an ongoing criminal investigation, one of the major challenges of this response to what is a radiological dispersal device event has been the inability to obtain all of the technical detail desired to perform assessments. This has complicated the ability to communicate effectively with citizens and members of the public health community. These and other lessons learned from this response will help prepare the public health community to respond more effectively to future contamination events involving radioactive dispersal in the environment.(author)

  15. Estimation of the impact of manufacturing tolerances on burn-up calculations using Monte Carlo techniques

    Energy Technology Data Exchange (ETDEWEB)

    Bock, M.; Wagner, M. [Gesellschaft fuer Anlagen- und Reaktorsicherheit mbH, Garching (Germany). Forschungszentrum

    2012-11-01

    In recent years, the availability of computing resources has increased enormously. There are two ways to take advantage of this increase in analyses in the field of the nuclear fuel cycle, such as burn-up calculations or criticality safety calculations. The first possible way is to improve the accuracy of the models that are analyzed. For burn-up calculations this means, that the goal to model and to calculate the burn-up of a full reactor core is getting more and more into reach. The second way to utilize the resources is to run state-of-the-art programs with simplified models several times, but with varied input parameters. This second way opens the applicability of the assessment of uncertainties and sensitivities based on the Monte Carlo method for fields of research that rely heavily on either high CPU usage or high memory consumption. In the context of the nuclear fuel cycle, applications that belong to these types of demanding analyses are again burn-up and criticality safety calculations. The assessment of uncertainties in burn-up analyses can complement traditional analysis techniques such as best estimate or bounding case analyses and can support the safety analysis in future design decisions, e.g. by analyzing the uncertainty of the decay heat power of the nuclear inventory stored in the spent fuel pool of a nuclear power plant. This contribution concentrates on the uncertainty analysis in burn-up calculations of PWR fuel assemblies. The uncertainties in the results arise from the variation of the input parameters. In this case, the focus is on the one hand on the variation of manufacturing tolerances that are present in the different production stages of the fuel assemblies. On the other hand, uncertainties that describe the conditions during the reactor operation are taken into account. They also affect the results of burn-up calculations. In order to perform uncertainty analyses in burn-up calculations, GRS has improved the capabilities of its general

  16. H infinity Integrated Fault Estimation and Fault Tolerant Control of Discrete-time Piecewise Linear Systems

    DEFF Research Database (Denmark)

    Tabatabaeipour, Seyed Mojtaba; Bak, Thomas

    2012-01-01

    In this paper we consider the problem of fault estimation and accommodation for discrete time piecewise linear systems. A robust fault estimator is designed to estimate the fault such that the estimation error converges to zero and H∞ performance of the fault estimation is minimized. Then, the es...

  17. A study of Polonium in human hair and in fur from animals

    International Nuclear Information System (INIS)

    Holstein, H; Ranebo, Y.; Henriksson, F.; Rääf, C.L.; Holm, E.; Roos, P.

    2013-01-01

    Human hair and hair from animals might serve as good indicators for internal contamination, allowing for the quantification of general environmental levels of certain radioactive elements. From a sampling, analytical and hygienic point of view it would be advantageous to study hair instead of urine and faeces samples. There have been several investigations concerning Polonium in hair. The purpose of this study was to investigate if hair from humans and fur from animals constitute as matrixes for the estimation of the body burden of 210 Po. Human hair taken from 26 individuals from Sweden was analyzed for its 210 Po content. The resulting activity concentration of 210 Po ranged from 0.5 to 4.8 Bq/kg for individuals between the ages of 3 to 32 years and range from 0.5 to 11.5 Bq/kg for individuals between the ages of 32 to 60. This is in agreement with results presented in other studies. The 210 Po in hair might be due to external contamination or in vivo build up from 210 Pb. To help quantify these sources of contamination a couple of human volunteers ingested known amounts of 209 Po (which does not exist in nature). Results from the study showed that 209 Po was rather rapidly detected in the hair samples Human hair consists of 45% Carbon, 7% Hydrogen, 28% Oxygen, 15% Nitrogen and 5% Sulphur. The central core consists of polypeptide chains with hydrogen and disulphide bindings. It is suggested that the sulphide binding is the reason for transfer of Polonium into the hair. Samples from horses; mane, fur, and tail showed activity concentration levels ranging from 6 to 17 Bq/kg, with no significant differences between the various sample types. Fur samples taken from Muskox from Greenland showed much higher concentrations, i.e. 260 Bq/kg. This was expected since the animal graze over vast surface and consumes large amounts of lichen. Deposited radionuclides accumulate in lichens. Fur samples taken from other animals i.e. moose, hare, wild boar, roe deer, and sheep (lamb

  18. Investigation of electrostatic collection of some polonium radioisotopes for plane and hemispheric geometries

    International Nuclear Information System (INIS)

    Lobach, D.J.; Dezhurko, M.D.

    2004-01-01

    The model approach to the description of the electrostatic collection (precipitation) of short-lived radon daughter products (RDP) is presented. The considerations are based on speculations about current processes (oxidation ( k - the constant of polonium oxidation), recombination (α - the constant of recombination), neutralization (γ - the constant of polonium oxide neutralization) and radioactive decay (λ - the constant of radioactive decay)). The subscript Rn refers to radon; Po, to polonium ( 215 Po, 216 Po, 218 Po); PoO, to polonium oxide (PoO 2 ). There is continuous uniform ionization in working matter of plane electrostatic chamber for RDP collection (the length of the chamber is d). The formation intensity of ion pairs is q, which is in correlation to the volume activity (VA) of radioactive ions in the chamber and irradiation from external sources. It is neglected by ion diffusion during electrostatic collection. Recombination losses are from collisions of heavy ions solely. Positive ions are collected on the working surface of the detector (cathode of the electrostatic chamber). n ± is the volume concentration of positive (negative) ions; ω ± > 0 is the drift velocity of positive (negative) ions. The driftage of positive ions along x-axis (to the cathode) and the balance of ions in dx layer are considered. At k approaching infinity, k >> λ Po + αn - and it is possible to obtain a single expression for the two polonium fractions: ω +PoO (dn +PoO /dx) = λ Rn n Rn - α n +PoO n - - γ n +PoO - λ Po n +PoO . The driftage time of positive ions in plane electrostatic chamber should be τ(drift) = d/ω + PoO is the mobility of polonium ions or aerosol complexes with polonium: ε(U) = [(μ PoO . U)/(d 2 . (λ Po + γ))] . [1 - exp [(d 2 . (λ Po + γ))/(μ PoO . U)

  19. Equilibrium evaporation behavior of polonium and its homologue tellurium in liquid lead-bismuth eutectic

    International Nuclear Information System (INIS)

    Ohno, Shuji; Miyahara, Shinya; Kurata, Yuji; Katsura, Ryoei; Yoshida, Shigeru

    2006-01-01

    Experimental study using the transpiration method investigates equilibrium evaporation behavior of radionuclide polonium ( 210 Po) generated and accumulated in liquid lead-bismuth eutectic (LBE) cooled nuclear systems. The experiment consists of two series of tests: preliminary evaporation tests for homologue element tellurium (Te) in LBE, and evaporation tests for 210 Po-accumulated LBE in which test specimens are prepared by neutron irradiation. The evaporation tests of Te in LBE provide the suggestion that Te exists in a chemical form of PbTe as well as the information for confirming the validity of technique and conditions of Po test. From the evaporation tests of 210 Po in LBE, we obtain fundamental data and empirical equations such as 210 Po vapor concentration in the gas phase, 210 Po partial vapor pressure, thermodynamic activity coefficients, and gas-liquid equilibrium partition coefficient of 210 Po in LBE in the temperature range from 450 to 750degC. Additionally, radioactivity concentration of 210 Po and 210m Bi vapor in a cover gas region of a typical LBE-cooled nuclear system is specifically estimated based on the obtained experimental results, and the importance of 210 Po evaporation behavior is quantitatively demonstrated. (author)

  20. Determination of internal radiation dose due to intake of polonium 210 and lead 210 via smoking

    International Nuclear Information System (INIS)

    Al-Masri, M. S.; Kharita, M.H.; Nashawati, A.; Amin, Y.; Al-Akel, B.

    2004-12-01

    In this study, 18 kind of cigarettes and five kinds of molasses consumed by Syrians were collected and analyzed for radioactivity in order to estimate the internal radiation dose caused by 210 Po and 210 Pb intake. Polonium 210 and lead 210 concentrations varied between 4 and 16.4 m Bq/cigarette, while 210 Po distribution ratios in different parts of consumed cigarette were %12, %73, %1.6 in ash, smoke and filter, respectively. In addition, annual intake of 210 Po by a main smoker was varied between 4.4 and 18 Bq/year assuming that the main smoker breathes about 15% of the total 210 Po present in tobacco. Using the values of the annual intake, annual equivalent radiation dose caused by smoking has reached 178 μSv/year. Moreover, mean concentration of 210 Po in nonsmokers and smokers bloods has reached 130 and 97 mBq/l, respectively, while the mean value of 210 Po concentration was relatively higher and reached 176 and 155 mBq/l in smokers and non smoker bloods, respectively (Authors)

  1. Ab initio study of the trapping of polonium on noble metals

    Science.gov (United States)

    Rijpstra, Kim; Van Yperen-De Deyne, Andy; Maugeri, Emilio Andrea; Neuhausen, Jörg; Waroquier, Michel; Van Speybroeck, Veronique; Cottenier, Stefaan

    2016-04-01

    In the future MYRRHA reactor, lead bismuth eutectic (LBE) will be used both as coolant and as spallation target. Due to the high neutron flux a small fraction of the bismuth will transmute to radiotoxic 210Po. Part of this radiotoxic element will evaporate into the gas above the coolant. Extracting it from the gas phase is necessary to ensure a safe handling of the reactor. An issue in the development of suitable filters is the lack of accurate knowledge on the chemical interaction between a candidate filter material and either elemental polonium or polonium containing molecules. Experimental work on this topic is complicated by the high radiotoxicity of polonium. Therefore, we present in this paper a first-principles study on the adsorption of polonium on noble metals as filter materials. The adsorption of monoatomic Po is considered on the candidate filter materials palladium, platinum, silver and gold. The case of the gold filter is looked upon in more detail by examining how bismuth pollution affects its capability to capture polonium and by studying the adsorption of the heavy diatomic molecules Po2, PoBi and PoPb on this gold filter.

  2. A study on optimum conditions for reducing Polonium-210 ion in electrolysis process

    International Nuclear Information System (INIS)

    Yii Mei Wo

    2006-01-01

    Polonium-210 is one of the most important radionuclide to be study while studying radioactive contaminants on marine lives. It usually be self-deposited on a pure silver foil and counted using an Alpha Spectrometry System. However, using pure silver foil involves high cost. Therefore, study had been conducted to find the suitability of using stainless steel disc to deposit polonium-210 using electrolysis process and the optimum conditions for such process. This was carry out by using pure polonium-210 standard solution and the ready disc was counted using Zinc Sulphite Counter. Results show that reduction of polonium ion on stainless steel disc can be done but the efficiency of the process only around 70 percent. Besides this, studies also show that, at 1.1 ampere constant current and cathode to anode distance at 8 mm, the optimum conditions to reduce polonium ion were at pH 2.2-2.3 with the electrolysis time of 5 hours. (Author)

  3. Ab initio study of the trapping of polonium on noble metals

    Energy Technology Data Exchange (ETDEWEB)

    Rijpstra, Kim; Van Yperen-De Deyne, Andy [Center for Molecular Modeling (CMM), Ghent University, Technologiepark 903, 9052 Ghent (Belgium); Maugeri, Emilio Andrea; Neuhausen, Jörg [Laboratory for Radiochemistry, Paul Scherrer Institute (PSI), 5232 Villigen (Switzerland); Waroquier, Michel; Van Speybroeck, Veronique [Center for Molecular Modeling (CMM), Ghent University, Technologiepark 903, 9052 Ghent (Belgium); Cottenier, Stefaan, E-mail: stefaan.cottenier@ugent.be [Center for Molecular Modeling (CMM), Ghent University, Technologiepark 903, 9052 Ghent (Belgium); Department of Materials Science and Engineering, Ghent University, Technologiepark 903, 9052 Ghent (Belgium)

    2016-04-15

    In the future MYRRHA reactor, lead bismuth eutectic (LBE) will be used both as coolant and as spallation target. Due to the high neutron flux a small fraction of the bismuth will transmute to radiotoxic {sup 210}Po. Part of this radiotoxic element will evaporate into the gas above the coolant. Extracting it from the gas phase is necessary to ensure a safe handling of the reactor. An issue in the development of suitable filters is the lack of accurate knowledge on the chemical interaction between a candidate filter material and either elemental polonium or polonium containing molecules. Experimental work on this topic is complicated by the high radiotoxicity of polonium. Therefore, we present in this paper a first-principles study on the adsorption of polonium on noble metals as filter materials. The adsorption of monoatomic Po is considered on the candidate filter materials palladium, platinum, silver and gold. The case of the gold filter is looked upon in more detail by examining how bismuth pollution affects its capability to capture polonium and by studying the adsorption of the heavy diatomic molecules Po{sub 2}, PoBi and PoPb on this gold filter.

  4. A study of polonium-210 distribution in Syrian phosphogypsum and its leaching mechanisms

    International Nuclear Information System (INIS)

    Al-Masri, M.S.; Al-Bich, F.

    2000-02-01

    Polonium 210 distribution in Syrian phosphogypsum and its leaching mechanisms have been evaluated. Radiochemical analysis have shown that 210 Po concentration in Syrian phosphogypsum is always higher than 226 Po concentrations were found to vary between 373 and 589 Bq.Kg -1 with an average value of 471 Bq.Kg -1 , which is lower than those values reported in other countries. 210 Po was found to be more enhanced in smaller particles; a specific activities of 827 Bq.Kg -1 in particles with size less than 250 mesh being observed. Leaching experiments using distilled water have shown that 210 are strongly bounded to phosphogypsum particles. The amount of 210 Po transferred to aqueous media does not exceed 5.6% and 8.4% for batch wise and continuous leaching respectively; lowering the ph has increased this percentage to 20%. In addition, leaching with diluted sulfuric acid indicated that 80% of polonium is present as water insoluble quadrivalent polonium sulphate while 20% as soluble simple polonium sulfate (2PoO 2 .So 3 ). While leaching with selective agents such as MgCl 2 and NH 4 AC have shown that 58% of polonium is present on the surface of gypsum lattice. However, the obtained data could be used to explain environmental pathway of 210 Po from phosphogypsum. (Author)

  5. Review of chemical and radiotoxicological properties of polonium for internal contamination purposes.

    Science.gov (United States)

    Ansoborlo, Eric; Berard, Philippe; Den Auwer, Christophe; Leggett, Rich; Menetrier, Florence; Younes, Ali; Montavon, Gilles; Moisy, Philippe

    2012-08-20

    The discovery of polonium (Po) was first published in July, 1898 by P. Curie and M. Curie. It was the first element to be discovered by the radiochemical method. Polonium can be considered as a famous but neglected element: only a few studies of polonium chemistry have been published, mostly between 1950 and 1990. The recent (2006) event in which (210)Po evidently was used as a poison to kill A. Litvinenko has raised new interest in polonium. 2011 being the 100th anniversary of the Marie Curie Nobel Prize in Chemistry, the aim of this review is to look at the several aspects of polonium linked to its chemical properties and its radiotoxicity, including (i) its radiochemistry and interaction with matter; (ii) its main sources and uses; (iii) its physicochemical properties; (iv) its main analytical methods; (v) its background exposure risk in water, food, and other environmental media; (vi) its biokinetics and distribution following inhalation, ingestion, and wound contamination; (vii) its dosimetry; and (viii) treatments available (decorporation) in case of internal contamination.

  6. Determination of the polonium-210 content in the urine of Filipino smokers and non-smokers

    International Nuclear Information System (INIS)

    Juan, N.B.; Ballelos, E.; Bartolome, Z.M.

    1975-01-01

    Presence of polonium in tobacco poses a health hazard to smokers. Polonium is a pure alpha emitter with an energy of 5.3 MeV decaying with a half-life 138.4 days to a stable isotope of lead. The polonium content in the urine of Filipino smokers was compared with that of non-smokers. The polonium was recovered from urine by centrifugation and deposition into silver discs. Quantitative results were obtained by counting the silver discs using a silicon surface-barrier detector. The average value obtained for smokers which was 0.5003+-0.2988 pCi/24h sample was significantly higher than the value obtained for non-smokers which was 0.2313+-0.1664 pCi/24h sample. The efficiency of the procedure employed encourages the use of urinalysis as a measure of the polonium body burden and also as a rough index of the dose absorbed from radium or any of its daughters

  7. Polonium-210: the challenges in advising the law enforcement community during the investigation into the death of Alexander Litvinenko

    International Nuclear Information System (INIS)

    Cairns, James M.

    2008-01-01

    Full text: The death of Alexander Litvinenko in November 2006 delivered unique challenges for the radiological protection of emergency responders. The need to identify a cause of death and investigate a potential crime balanced against the need for the radiological safety of both the investigator staff and protection of the public led to a number of situations requiring unique solutions. Polonium 210 is a naturally occurring radioactive substance that appears as part of the uranium-235 decay series. It has a 138 day half-life with a specific activity of 1.66 x 10 14 Bq/g. It is considered for radiological purposes as an alpha emitter though it does have a low probability ( 4 Bq and ingestion of 6.7 x 10 3 Bq meaning that physical quantities of less than 1 μg are lethal. The first blood and urine samples from Mr Litvinenko were analysed by the author and his team who identified a 803 keV peak from gamma spectral analysis. After discussions with medical staff and the Senior Investigation Officer, an additional sample was taken to permit the completion of more detailed analytical techniques specifically for polonium-210. Using liquid scintillation counting and alpha spectrometry on the additional urine sample led to an estimated body burden within 10% of the final assessed intake from post-mortem samples. The investigation raised the following challenges to the author and Law Enforcement Personnel: a) Tracing the movement of the victim and his associates to; piece together a potential point and route of intake; and identify potential contamination areas requiring public protection measures by health agencies; b) Collection of evidence in a contaminated environment; c) Processing of contaminated forensics samples; d) Undertaking a post-mortem in a mortuary not designed for the processing of radiologically contaminated personnel; e) Identifying routes for obtaining polonium-210 including a review of historical papers from the UK, US and Russian early nuclear weapon

  8. Method for evaluation of doses from ingestion of polonium, bismuth and lead as natural radioactive material(NORM); Metodo de evaluacion de dosis por ingestion de polonio, bismuto y plomo como materiales radiactivos naturales

    Energy Technology Data Exchange (ETDEWEB)

    Pena, Vanessa; Puerta, Anselmo; Morales, Javier, E-mail: vpenam@ullal.edu.co, E-mail: japuerta@unal.edu.co, E-mail: jmorales@unal.cdu.co [Universidad Nacional de Colombia, Medellin (Colombia). Grupo de Fisica Radiologica

    2013-07-01

    In this work was carried out an evaluation of dose from ingestion of radioactive daughters of radon (lead, bismuth and polonium), taking into account ages from three months up to adult men, using the new model of the human alimentary tract HATM and methodology of calculating doses proposed by the ICRP publication 103, which allows the estimation of dose based on the concentration of the radionuclide present in the diet or in the water of consumption.

  9. Large deficiency of polonium in the oligotrophic ocean's interior

    Science.gov (United States)

    Kim, Guebuem

    2001-09-01

    The naturally occurring radionuclide 210Po is typically deficient relative to its parent 210Pb in the surface ocean due to preferential removal by biota, while in near equilibrium or excess below the surface mixed layer due to rapid regeneration from sinking organic matter. However, a strikingly large deficit of 210Po is observed in the oligotrophic Sargasso Sea's interior. This argues against the general concept that the removal of reactive elements depends on the population of settling particles. A 210Po mass balance model suggests that rather than downward transport, polonium (proxy for S, Se, and Te) is taken up efficiently by bacteria (i.e., cyanobacteria) and transferred to higher trophic levels (i.e., nekton) in this environment. In contrast, in productive areas of the ocean, sulfur group elements seem to reside in the subsurface ocean for much longer periods as taken up by abundant free-living bacteria (non-sinking fine particles). This study sheds new light on global biogeochemical cycling of sulfur group elements in association with microbial roles, and suggests that 210Po may be useful as a tracer of nitrogen fixation in the ocean.

  10. Transfer factors of Polonium from soil to parsley and mint

    International Nuclear Information System (INIS)

    Al-Masri, M.S.; Al-Hamwi, A.; Eadan, Z.; Amin, Y.

    2010-01-01

    Transfer factors of 210 Po from soil to parsley and mint have been determined. Artificial polonium isotope ( 208 Po) was used as a tracer to determine transfer factor of Po from soil to plant in pot experiments. Two plant growing systems were used for this study namely, an outdoor system and a sheltered system by a polyethylene tent. 208 Po and 210 Po were determined in soil and different parts of the studied plants (stem and leaf), using alpha spectroscopy. The results have shown that there was a clear uptake of 208 Po by roots to leaves and stems of both plants. Higher values of transfer factors using the 210 Po activity concentrations than the 208 Po activity concentration were observed. Transfer factors of 210 Po from soil to parsley varied between 20 x 10 -2 and 50 x 10 -2 and 22 x 10 -3 and 67 x 10 -3 in mint, while 208 Po transfer factors varied between 4 x 10 -2 and 12 x 10 -2 for parsley and 10 x 10 -2 and 22 x 10 -2 in mint. Transfer factors of Po were higher in those plants grown in the sheltered system than in the open system; about 75% of Po was transferred from atmosphere to parsley parts using the two systems. Ratios of transferred Po from soil to mint stem and leaf in the sheltered system were higher by 2 times from those in the open system.

  11. Coulomb excitation of neutron-deficient polonium isotopes studied at ISOLDE

    CERN Document Server

    Neven, Michiel

    The polonium isotopes represent an interesting region of the nuclear chart having only two protons outside the Z = 82 closed shell. These isotopes have already been extensively studied theoretically and experimentally. The heavier isotopes (A > 200) seem to follow a "regular seniority-type regime" while for the lighter isotopes (A < 200) a more collective behavior is observed. Many questions remain regarding the transition between these two regimes and the configuration mixing between quantum states. Experiments in the lighter polonium isotopes point to the presence of shape coexistence, however the phenomenon is not fully understood. A Coulomb excitation study of the polonium isotopes whereby the dynamic properties are investigated can provide helpful insights in understanding the shape coexistence phenomena. In this thesis $^{202}$Po was studied via Coulomb excitation. The $^{202}$Po isotope was part of an experimental campaign in which the $^{196,198,200,206}$Po isotopes were studied as well via Coulomb...

  12. Polonium-210 in the environment around a radioactive waste disposal area and phosphate ore processing plant

    Energy Technology Data Exchange (ETDEWEB)

    Arthur, III, W J; Markham, O D

    1984-04-01

    Polonium-210 concentrations were determined for soil, vegetation and small mammal tissues collected at a solid radioactive waste disposal area, near a phosphate ore processing plant and at two rural areas in southeastern Idaho. Polonium concentrations in media sampled near the radioactive waste disposal facility were equal to or less than values from rural area samples, indicating that disposal of solid radioactive waste at the Idaho National Engineering Laboratory Site has not resulted in increased environmental levels of polonium. Concentrations of /sup 210/Po in soils, deer mice hide and carcass samples collected near the phosphate processing plant were statistically greater than the other sampling locations; however, the mean /sup 210/Po concentration in soils and small mammal tissues from sampling areas near the phosphate plant were only four and three times greater, respectively, than control values. No statistical difference was observed for /sup 210/Po concentrations in vegetation among any of the sampling locations.

  13. Effect of polonium alpha-radiation on aqueous solutions (the history of French and Russian studies)

    International Nuclear Information System (INIS)

    Vladimirova, M.V.

    1998-01-01

    Since Pierre and Marie Curie's discovery of polonium and radium the effect of their radiation on chemical systems was noted. This gave rise to a new science - radiation chemistry. Systematic studies of radiation effects go back to the mid-1940s. The effect of gamma and x radiation was studied most, while only M. Curie's laboratory in France was concerned with alpha emitting polonium and radon. M. Haissinsky, M. Lefort, P. Bonet-Marry, M. Anta pioneered this activity. Radon was soon abandoned in favour of polonium recovered from RaD. With its short half-life, polonium is an ideal emitter which at its low content by weight produces a highly intensive radiation. French scientists determined radiation yields of H 2 , O 2 , H 2 O 2 and that of water radiolytic decomposition, G[-H 2 O]. The latter was found to be equal to 3.5 molecule/100 eV and much less than that from gamma radiolysis (4.2 molecule/100 eV). It should be noted that the polonium recovered from RaD contained a variety of impurities influencing the yield of radiolysis products formed. From the outset of her study in 1957, the author of this paper used the purest polonium recovered from reactor-irradiated Bi-209. This made it possible to define the yields from alpha radiolysis of various aqueous solutions more exactly. Relying on the J. Pucheault hypothesis concerning the decomposition of molecular radiolysis products in heavy particle tracks, author's efforts were directed toward the quantification of initial radiolysis yields. Special experiments have shown that G[-H 2 O] is much the same from alpha and gamma radiolysis (around 4.2 molecule/100eV). The author had the good luck to discuss her results with Pr. M. Haissinsky from Laboratory Curie. (author)

  14. Determination of polonium-210 levels in some syrian soils and crops

    International Nuclear Information System (INIS)

    Othman, I.; Al-Masri, M.S.; Aba, A.A.; Mukhallaty, H.; Al-Hamwy, A.; Khalili, H.

    1997-04-01

    Polonium 210 levels in the edible port of 19 agricultural crops collected from ten locations in Syria have been determined. Results have been shown that the highest concentrations were found to be in parsley (10.49 Bq/Kg) and this due to high area of its levels. Moreover, the concentrations were low in some vegetables such as tomatoes (0.2 Bq/Kg). In addition, polonium 210 was also determined in Syria soil where it was found to vary between 20 Bq/Kg and 68.8 Bq/Kg). (author). 11 refs., 17 tabs

  15. The Technique for the Numerical Tolerances Estimations in the Construction of Compensated Accelerating Structures

    CERN Document Server

    Paramonov, V V

    2004-01-01

    The requirements to the cells manufacturing precision and tining in the multi-cells accelerating structures construction came from the required accelerating field uniformity, based on the beam dynamics demands. The standard deviation of the field distribution depends on accelerating and coupling modes frequencies deviations, stop-band width and coupling coefficient deviations. These deviations can be determined from 3D fields distribution for accelerating and coupling modes and the cells surface displacements. With modern software it can be done separately for every specified part of the cell surface. Finally, the cell surface displacements are defined from the cell dimensions deviations. This technique allows both to define qualitatively the critical regions and to optimize quantitatively the tolerances definition.

  16. Transfer factors of polonium from soil to parsley and mint.

    Science.gov (United States)

    Al-Masri, M S; Al-Hamwi, A; Eadan, Z; Amin, Y

    2010-12-01

    Transfer factors of (210)Po from soil to parsley and mint have been determined. Artificial polonium isotope ((208)Po) was used as a tracer to determine transfer factor of Po from soil to plant in pot experiments. Two plant growing systems were used for this study namely, an outdoor system and a sheltered system by a polyethylene tent. (208)Po and (210)Po were determined in soil and different parts of the studied plants (stem and leaf), using alpha spectroscopy. The results have shown that there was a clear uptake of (208)Po by roots to leaves and stems of both plants. Higher values of transfer factors using the (210)Po activity concentrations than the (208)Po activity concentration were observed. Transfer factors of (210)Po from soil to parsley varied between 20 × 10⁻² and 50 × 10⁻² and 22 × 10⁻³ and 67 × 10⁻³ in mint, while (208)Po transfer factors varied between 4 × 10⁻² and 12 × 10⁻² for parsley and 10 × 10⁻² and 22 × 10⁻² in mint. Transfer factors of Po were higher in those plants grown in the sheltered system than in the open system; about 75% of Po was transferred from atmosphere to parsley parts using the two systems. Ratios of transferred Po from soil to mint stem and leaf in the sheltered system were higher by 2 times from those in the open system. Copyright © 2010 Elsevier Ltd. All rights reserved.

  17. Transfer factors of Polonium from soil to parsley and mint

    Energy Technology Data Exchange (ETDEWEB)

    Al-Masri, M.S., E-mail: prscientific@aec.org.s [Department of Protection and Safety, Atomic Energy Commission of Syria, Damascus, P.O. Box 6091 (Syrian Arab Republic); Al-Hamwi, A. [Department of Protection and Safety, Atomic Energy Commission of Syria, Damascus, P.O. Box 6091 (Syrian Arab Republic); Eadan, Z. [Physics Department, Damascus University (Syrian Arab Republic); Amin, Y. [Department of Protection and Safety, Atomic Energy Commission of Syria, Damascus, P.O. Box 6091 (Syrian Arab Republic)

    2010-12-15

    Transfer factors of {sup 210}Po from soil to parsley and mint have been determined. Artificial polonium isotope ({sup 208}Po) was used as a tracer to determine transfer factor of Po from soil to plant in pot experiments. Two plant growing systems were used for this study namely, an outdoor system and a sheltered system by a polyethylene tent. {sup 208}Po and {sup 210}Po were determined in soil and different parts of the studied plants (stem and leaf), using alpha spectroscopy. The results have shown that there was a clear uptake of {sup 208}Po by roots to leaves and stems of both plants. Higher values of transfer factors using the {sup 210}Po activity concentrations than the {sup 208}Po activity concentration were observed. Transfer factors of {sup 210}Po from soil to parsley varied between 20 x 10{sup -2} and 50 x 10{sup -2} and 22 x 10{sup -3} and 67 x 10{sup -3} in mint, while {sup 208}Po transfer factors varied between 4 x 10{sup -2} and 12 x 10{sup -2} for parsley and 10 x 10{sup -2} and 22 x 10{sup -2} in mint. Transfer factors of Po were higher in those plants grown in the sheltered system than in the open system; about 75% of Po was transferred from atmosphere to parsley parts using the two systems. Ratios of transferred Po from soil to mint stem and leaf in the sheltered system were higher by 2 times from those in the open system.

  18. Finite Time Fault Tolerant Control for Robot Manipulators Using Time Delay Estimation and Continuous Nonsingular Fast Terminal Sliding Mode Control.

    Science.gov (United States)

    Van, Mien; Ge, Shuzhi Sam; Ren, Hongliang

    2016-04-28

    In this paper, a novel finite time fault tolerant control (FTC) is proposed for uncertain robot manipulators with actuator faults. First, a finite time passive FTC (PFTC) based on a robust nonsingular fast terminal sliding mode control (NFTSMC) is investigated. Be analyzed for addressing the disadvantages of the PFTC, an AFTC are then investigated by combining NFTSMC with a simple fault diagnosis scheme. In this scheme, an online fault estimation algorithm based on time delay estimation (TDE) is proposed to approximate actuator faults. The estimated fault information is used to detect, isolate, and accommodate the effect of the faults in the system. Then, a robust AFTC law is established by combining the obtained fault information and a robust NFTSMC. Finally, a high-order sliding mode (HOSM) control based on super-twisting algorithm is employed to eliminate the chattering. In comparison to the PFTC and other state-of-the-art approaches, the proposed AFTC scheme possess several advantages such as high precision, strong robustness, no singularity, less chattering, and fast finite-time convergence due to the combined NFTSMC and HOSM control, and requires no prior knowledge of the fault due to TDE-based fault estimation. Finally, simulation results are obtained to verify the effectiveness of the proposed strategy.

  19. Comparison of AC electronic monitoring and field data for estimating tolerance to Empoasca kraemeri (Homoptera: Cicadellidae) in common bean genotypes.

    Science.gov (United States)

    Serrano, M S; Backus, E A; Cardona, C

    2000-12-01

    Two methods for estimating the tolerance of common bean genotypes to Empoasca kraemeri Ross & Moore were compared, using a yield trial carried out at Centro Internacional de Agricultura Tropical (CIAT), Cali, Colombia, versus stylet penetration tactics measured by AC electronic feeding monitors. A stylet penetration index was devised based on principal component scores of three penetration tactics identified (pulsing laceration, cell rupturing, and lancing sap ingestion), combined with knowledge of the hopperburn symptoms caused by each tactic. Tolerant genotypes, as classified by the CIAT yield index, showed significantly more unprotected yield and lower hopperburn scores than the susceptible control. They also induced performance of less pulsing laceration (the tactic considered most damaging to the plant), and more of the other two, mitigating tactics, especially cell rupturing. When index values were calculated for each genotype, stylet penetration index values matched those of the yield index for three out of five genotypes: two EMP-coded tolerant lines ('EMP 385' and 'EMP 392') and the susceptible control 'BAT 41'. Thus, for these three genotypes, all subsequent hoppereburn symptoms are predictable by the type of feeding behavior performed on them. 'Porrillo Sintético' and 'EMP 84', considered borderline genotypes by the yield index, were overestimated and underestimated respectively, by the stylet penetration index. We postulate that, for these two genotypes, plant physiological responses to feeding (either compensatory or heightened sensitivity, respectively) synergize with type of feeding performed to generate the overall hopperburn condition. This multivariate analysis of electronic monitoring data was successfully used to devise an index of resistance. The implications of using the stylet penetration index and the advantages of using electronic monitoring in a bean-breeding program are discussed.

  20. Removal of polonium contamination by lead-bismuth eutectic in nuclear systems

    International Nuclear Information System (INIS)

    Miura, Terumitsu; Obara, Toru; Sekimoto, Hiroshi

    2003-01-01

    Lead-Bismuth eutectic (LBE) is considered as a promising candidate of the coolant of liquid metal cooled fast reactor, and the coolant and/or target of accelerator driven system. LBE has various good characters for coolant, but it has also some problems such as polonium production. It is necessary to take polonium contamination into consideration, when LBE is used as the coolant. In the present paper, the removal of contaminating polonium from material surface is studied. Baking method is investigated for polonium removal from contaminated quartz glass plate in vacuum. Before and after baking, the mass of the contaminants on the surface and alpha particle counts from contaminated surface is measured. When the contaminated quartz glass plates are baked at more than 400degC for a few minutes, alpha particle counts from the surface decreases by more than 99.7%, and the mass of contaminants decreases by more than 50%. When the baking was performed at 300degC for 15 minutes and more, alpha particle count decreases by more than 80%, and the mass decreases in little. When, the baking temperature is lower than 200degC, alpha particle counts and mass do not decrease. (author)

  1. Polonium-210 in cartilaginous fishes (Chondrichthyes) from south-eastern Australian waters

    International Nuclear Information System (INIS)

    Smith, D.J.; Towler, H.

    1993-01-01

    A study was made of the concentration of the naturally occurring radionuclide polonium-210 in the livers of cartilaginous fishes (chondrichthyans) caught in the waters of Port Phillip Bay, Victoria, Australia in 1991. Five elasmobranch species had 210 Po concentrations in the range 1-31 Bq kg -1 (wet weight) and one holocephalian species, the elephant fish (Callorhynchus milii), was exceptional with a 210 Po range of 60-270 Bq kg -1 (n-3, mean 180 Bq kg -1 ). Lead-210 was present at 0.1-1.1 Bq kg -1 and activity concentration ratios of 210 Po: 210 Pb were all greater than 1, indicating that the 210 Po could not all have grown in from in situ decay of 210 Pb within the chondrichthyan liver. The concentration of 210 Po in the livers appeared to be species related. Concentrations of the trace metals Cu, Fe and Zn showed no correlation with the 210 Po and were not species-related. The mean concentration of 210 Po measured in Port Phillip Bay water was 0.32 mBq kg -1 . This yields concentration factors of 3.2 x 10 3 to 8.4 x 10 5 for unsupported 210 Po in the livers of the chondrichthyans. The total 210 Po (using Q=20) exposes the livers to a weighted absorbed dose of up to 140 mGy year -1 (16 μGy h -1 ), which is >99% of the total internal dose and three orders of magnitude greater than the external dose based on estimated levels of 40 K. 18 refs., 3 tabs., 2 figs

  2. Improving the Dominating-Set Routing over Delay-Tolerant Mobile Ad-Hoc Networks via Estimating Node Intermeeting Times

    Directory of Open Access Journals (Sweden)

    Preiss Bruno

    2011-01-01

    Full Text Available With limited coverage of wireless networks and frequent roaming of mobile users, providing a seamless communication service poses a technical challenge. In our previous research, we presented a supernode system architecture that employs the delay-tolerant network (DTN concept to provide seamless communications for roaming users over interconnected heterogeneous wireless networks. Mobile ad hoc networks (MANETs are considered a key component of the supernode system for services over an area not covered by other wireless networks. Within the super node system, a dominating-set routing technique is proposed to improve message delivery over MANETs and to achieve better resource utilization. The performance of the dominating-set routing technique depends on estimation accuracy of the probability of a future contact between nodes. This paper studies how node mobility can be modeled and used to better estimate the probability of a contact. We derive a distribution for the node-to-node intermeeting time and present numerical results to demonstrate that the distribution can be used to improve the dominating-set routing technique performance. Moreover, we investigate how the distribution can be employed to relax the constraints of selecting the dominating-set members in order to improve the system resource utilization.

  3. Polonium 210Po activities in human blood of patients with ischaemic heart disease from Gda?sk in Poland

    OpenAIRE

    Bory?o, Alicja; Skwarzec, Bogdan; Roma?czyk, Grzegorz; Siebert, Janusz

    2013-01-01

    The determination of polonium 210Po in human blood samples is presented and discussed in this paper. The human blood samples were collected from patients of Medical University of Gda?sk with ischaemic heart disease (morbus ischaemicus cordis, MIC). The polonium concentrations in analyzed human blood samples are very differentiated. 210Po is of particular interest in public health and although is present in the environment in extremely low amounts, it is easily bioaccumulated to the human body...

  4. PMS49 – Empirical comparison of discrete choice experiment and best-worst scaling to estimate stakeholders' risk tolerance for hip replacement surgery

    NARCIS (Netherlands)

    van Dijk, J.D.; Groothuis-Oudshoorn, Karin; Marshall, D.; IJzerman, Maarten Joost

    2013-01-01

    Objectives Empirical comparison of two preference elicitation methods, discrete choice experiment (DCE) and profile case best-worst scaling (BWS), regarding the estimation of the risk tolerance for hip replacement surgery (total hip arthroplasty and total hip resurfacing arthroplasty). Methods An

  5. Uranium series radionuclides, polonium-210 and lead-210, in the lichen-caribou-wolf food chain of the Northwest Territories

    International Nuclear Information System (INIS)

    Thomas, P.A.; Sheard, J.W.; Swanson, S.

    1994-01-01

    This report examines baseline concentrations and transfer of the uranium decay products polonium-210 and lead-210 in the lichen-caribou-wolf food chain at two locations in the Northwest Territories, Baker Lake and Snowdrift. At each location, concentrations of the two radionuclides were determined in the lichen species Cetraria nivalis and Cladina mitis, and several tissues from caribou and wolves. Baseline concentrations and transfer coefficients within the food chain were compared between the two locations. Lichen samples were also collected from Kasba Lake, a third hunting ground used by northern Saskatchewan hunters. The lichen species chosen were common forage for caribou. Both the predominant lichen species at each location and rumen contents were used to estimate the winter diet of caribou in the calculation of transfer coefficients. The results are relevant to environmental monitoring in areas of potential future uranium mining development and the transfer coefficients determined in the study may be used to estimate radionuclide concentrations and radiation doses in future environmental assessments

  6. Ingestion of polonium ((210)Po) via dietary sources in high background radiation areas of south India.

    Science.gov (United States)

    Arunachalam, Kantha Deivi; Baskaran, Kamesh Viswanathan; Rao, D D; Sathyapriya, R; Annamalai, Sathesh Kumar; Kuruva, Jaya Krishna; Hari, Shanmugamsundaram

    2014-10-01

    To study the distribution of Polonium ((210)Po) activity in dietary sources in the high background radiation zone of Puttetti in southern Tamil Nadu. (210)Po was analyzed in the food materials consumed by the male and female individual representatives living in the high background areas by 24-h Duplicate Diet Study (DDS) and Market Basket Study (MBS). The MBS was performed by collecting the food samples such as, cereals, fruits, leafy vegetables, roots and tubers, other vegetables, fish, meat and milk grown in the high background radiation zone of southern Tamil Nadu as a part of baseline study in this region. The DDS was done by collecting the food materials consumed including the beverages in 24 h from different age groups of male and female individuals living in the village of Puttetti. The intake and ingestion dose of the radionuclide (210)Po was estimated. The average concentration of (210)Po in DDS (n = 33) was found to be 74 mBq.kg(- 1) of fresh weight. The MBS was collected based on food consumption representing more than 85-95% of annual supply, and were divided into eight food groups. The average concentration of (210)Po in the eight food groups namely leafy vegetables was 2176 mBq.kg(- 1) (n = 3), vegetables 55 mBq.kg(- 1) (n = 10), roots and tubers 251 mBq.kg(- 1) (n = 4), fruits 65 mBq.kg(- 1) (n = 5), fish 345 mBq.kg(- 1) (n = 2), meat food 117 mBq.kg(- 1) (n = 3), milk 20 mBq.kg(- 1) (n = 1) and cereal 290 (n = 1) mBq.kg(- 1) of fresh weight, respectively. The annual intake and ingestion dose due to (210)Po was estimated by DDS and MBS in adults, adolescents and children. The overall results showed that the MBS was moderately higher than the DDS in all age groups. Moreover, a DDS approach may even be more realistic, as cooked foodstuffs are used for dietary exposure assessment. The study confirms that the current levels of (210)Po do not pose a significant radiological risk to the local inhabitants.

  7. Early onset of ground-state deformation in the neutron-deficient polonium isotopes

    CERN Document Server

    Cocolios, T E; Seliverstov, M D; Andreyev, A N; Antalic, S; Barzakh, A E; Bastin, B; Buscher, J; Darby, I G; Fedorov, D V; Fedosseyev, V N; Flanagan, K T; Franchoo, S; Fritzsche, S; Huber, G; Huyse, M; Keupers, M; Koster, U; Kudryavtsev, Yu; Mane, E; Marsh, B A; Molkanov, P L; Page, R D; Sjoedin, A M; Stefan, I; Van de Walle, J; Van Duppen, P; Venhart, M; Zemlyanoy, S G; Bender, M; Heenen, P H; 10.1103/PhysRevLett.106.052503

    2011-01-01

    In-source resonant ionization laser spectroscopy of the even-$A$ polonium isotopes $^{192-210,216,218}$Po has been performed using the $6p^37s$ $^5S_2$ to $6p^37p$ $^5P_2$ ($\\lambda=843.38$ nm) transition in the polonium atom (Po-I) at the CERN ISOLDE facility. The comparison of the measured isotope shifts in $^{200-210}$Po with a previous data set allows to test for the first time recent large-scale atomic calculations that are essential to extract the changes in the mean-square charge radius of the atomic nucleus. When going to lighter masses, a surprisingly large and early departure from sphericity is observed, which is only partly reproduced by Beyond Mean Field calculations.

  8. Study on auto-plating process time versus recovery for polonium, Po-210 in environmental sample

    International Nuclear Information System (INIS)

    Jalal Sharib; Zaharudin Ahmad; Abdul Kadir Ishak; Norfaizal Mohamed; Ahmad Sanadi Abu Bakar; Yii Mei Wo; Kamarozaman Ishak; Siti Aminah Yusoff

    2008-08-01

    This study was carried out to evaluate time effectiveness and recovery 16 samples of 4 Kuala Muda stations during auto-plating process procedures for determination Polonium, Po 210 activity concentration in environmental sample. The study was performed using Kuala Muda sediment as sample in the same methodology. The auto-plating process runs for 4, 12, 24 and 30 hours on a silver disc for 4 samples each station, and then counted for one (1) day using an alpha spectrometry counting system. The objectives for this study is to justify on time duration for auto-plating process effecting a chemical yield of Po-209.The results showed recovery are increasing versus time and constantly at 24 hour auto-plating. Its mean, 24 hour is an optimum time for auto-plating process for determination of Polonium, Po 210 activity concentration in environmental sample. (Author)

  9. Accumulation of polonium 210Po in tissues and organs of deer carvidae from Northern Poland.

    Science.gov (United States)

    Skwarzec, Bogdan; Prucnal, Malgorzata

    2007-01-01

    This study was undertaken to provide information on accumulation of polonium in tissues and organs of deer carvidae in order to assess the potential transport of this element via food-chain to game meat consumers. Livers, kidneys and muscles of large herbivorous animals belonging to three species: roe deer (Capreolus capreolus), red deer (Cervus elaphus) and fallow deer (Dama dama), collected in Northern Poland, were the subject of the present investigation. Activities of (210)Po were determined by means of alpha spectrometry along with relevant radiochemical procedures. The concentration of (210)Po in analyzed animals decreased in the order kidney > liver > muscle tissue. The average activity concentrations of (210)Po ranged between 0.02 +/- 0.01 Bq. kg(- 1) w.w. in muscles and 7.15 +/- 0.12 Bq. kg(- 1) w.w. in kidneys. Levels of polonium were not influenced by sampling location, sex, age and species of animals.

  10. Speciation, analysis and ion exchange behavior of polonium and other natural radionuclides in drinking water

    International Nuclear Information System (INIS)

    Katzlberger, C.J.

    2000-09-01

    In the first chapter of this work, the hydrolysis reaction of trace amounts of polonium was studied with a cation exchange method. In a 1 M (H,Na)ClO4 solution with p[H] > 0.3, polonium occurred in the form of univalent cation Po(OH)3+ and a neutral species Po(OH)4. The former is predominant in strongly acidic media (0.3 90 % determined via lead recovery with AAS. Minimum detectable activities of 0.4 mBq/l and 1.0 mBq/l could be achieved for 210Po and 210Bi (210Pb) respectively. Results ranged from 1.5-20 mBq/l and more in cases of extremely high 222Rn concentrations. Post sampling radon decay during the period between sampling and analysis plays an important role and strongly influences the obtained results. (author)

  11. Radiation studies in Lens culinaris: impact of absorbed polonium on microsporogenesis

    International Nuclear Information System (INIS)

    Singh, V.K.; Tauheed, Nusrat; Jha, V.N.; Tripathi, R.M.

    2008-01-01

    The root systems of fully grown plants of Lens culinaris (2n=14) were exposed to solutions of different concentrations of polonium (mixture of 208 Po and 209 Po Energy of alpha being 5.1 MeV and 4.9 MeV respectively). Variability in duration of exposure was also maintained. The controlled samples showed normal behavior of chromosomes forming seven bivalents with varying numbers of chiasmata. However, the pollen grain mother cells (PMC) of treated plants harbored a broad spectrum of chromosomal aberrations viz. Clumped configurations, multivalent formation, sticky anaphase bridge and laggards. Clumped configurations following surface stickiness was the most prominent manifestation. It appeared that the alpha particles emitted by the polonium atoms, logged in different organs including the anthers, created a situation akin to chronic internal radiation and inflicting injuries of different extent on the chromosome surface. (author)

  12. Polonium-210 in mussels and fish from the Baltic-North Sea estuary

    DEFF Research Database (Denmark)

    Dahlgaard, H.

    1996-01-01

    Polonium-210 has been measured in Danish fish meat caught in the North Sea, the Kattegat and the Baltic in 1991-1994. Average values of 0.35, 0.65 and 0.96 Bq Po-210 kg(-1) fresh weight were observed for cod, herring and plaice fillets, respectively. The difference between species is statistically...... in fish and mussels may represent a natural baseline. Copyright (C) 1996 Elsevier Science Ltd....

  13. Phase stability, elasticity, and theoretical strength of polonium from first principles

    Czech Academy of Sciences Publication Activity Database

    Legut, Dominik; Friák, Martin; Šob, Mojmír

    2010-01-01

    Roč. 81, č. 21 (2010), 214118/1/-214118/19/ ISSN 1098-0121 R&D Projects: GA AV ČR IAA100100920; GA MŠk(CZ) OC10008 Institutional research plan: CEZ:AV0Z20410507 Keywords : polonium * phase stability * elasticity * theoretical strength * ab initio calculations Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 3.772, year: 2010

  14. Investigation of corrosion, water reaction, polonium evaporation and bismuth resource in liquid metal lead-bismuth technology

    Energy Technology Data Exchange (ETDEWEB)

    Takano, Hideki; Takizuka, Takakazu [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Kitano, Teruaki [Mitsui Shipbuilding and Engineering Co. Ltd., Tokyo (Japan)

    2000-10-01

    Lead-bismuth is the first candidate material for liquid metal target find coolant of fueled blanket system in accelerator-driven system (ADS) studied at JAERI. Advantages of the lead-bismuth utilization are non-active material, very low capture cross section, low melting point of 125degC and high boiling point of 1670degC, and beside coolant void reactivity become negative. But problems are due to the high corrosivity to most of the structural materials and the corrosive data are scarcity. In this report, corrosivity, reaction with water, thermal-hydraulics, chemical toxicity etc. are studied by investigating some facilities utilized and researched really for lead or lead-bismuth. And, furthermore, polonium evaporation rate and bismuth resource are investigated. Main results obtained are as follows: (1) In a refinery, there are enough employment experience for liquid Pb-Bi in period of about 17 years and not corrosion for the thermal conductive materials (1Cr-0.5Mo steel) used under the condition of natural convection with temperature around 400degC. (2) In Russia, extensive experience in the use as Russian submarines and in R and D during about 50 years are available. And as a result, it will be able to lead approximately zero corrosion for Cr-Si materials by adjusting oxygen film with oxygen concentration control between 10{sup -7} to 10{sup -5}% mass. However, the corrosion data are not enough systematically collected involving them in radiation dose field. (3) In liquid-dropping experiment, it is shown that interaction between water and high temperature liquid Pb-Bi is reduced steeply with rising of atmosphere pressure. But, in order to design the second circuit removal model of ADS, the interaction should be evaluated by water continuous injection experiment. (4) Polonium forms PbPo in Pb-Bi, and the evaporation rate become less three factor than that of Po, and furthermore, the rate decreases in the atmosphere. The effects of Po on employee and environment

  15. Polonium content in sediments and other solid tailings generated by mining industry

    Energy Technology Data Exchange (ETDEWEB)

    Chmielewska, Izabela; Michalik, Boguslaw [Silesian Centre for Environmental Radioactivity, Central Mining Institute, 40-166 Katowice, Pl. Gwarkow 1 (Poland)

    2014-07-01

    All legal limits or recommendations concerning NORM include only primordial radionuclides and secular equilibrium state among all decay products is assumed. This is not valid for a majority of residues from NORM industry where activity concentration of progenies can substantially differ each other. Upper Silesia Coal Basin is a unique region where mining activity is continuously done over longer period of time and this include discharging of radium-bearing water to environment and creating huge amount of solid wastes where at the beginning radium is the most dominant radionuclide. With time other daughter products start to build up and actual exposure to radiation is changing. One of them is polonium that with regard to its chemical properties can be easily accumulated in non-human biota resulting in the increase of radiation exposure. In our work we focused attention on sediments where content of {sup 210}Po was determined by chemical separation followed by alpha spectrometry. Chemical preparation involves organic matter destruction and dissolution of the sample itself (if possible). In our research we employed wet digestion by means of mixture of concentrated acids: HNO{sub 3}, HClO{sub 4}, HCl. Later on polonium was spontaneously deposited onto silver disc and measured with use of alpha spectrometry. In this article we want to show results of our study and as well to present some conclusions concerning changes in radiation risk assessment when actual concentration of polonium is taken into consideration. (authors)

  16. Neutron-rich polonium isotopes studied with in-source laser spectroscopy

    CERN Document Server

    Dexters, Wim; Cocolios, T E

    This work studies the unknown region of neutron rich polonium isotopes. The polonium isotopes, with Z=84, lie above the magic lead nuclei (Z=82). The motivation for this research can mainly be found in these lead nuclei. When looking at the changes in the mean square charge radii beyond the N=126 shell gap, a kink is observed. This kink is also found in the radon (Z=86) and radium (Z=88) isotopes. The observed effect cannot be reproduced with our current models. The polonium isotopes yield more information on the kink and they are also able to link the known charge radii in lead isotopes to those in radon and radium. Additionally, the nuclear moments of the odd-neutron isotope $^{211}$Po are investigated. This nucleus has two protons and one neutron more than the doubly magic nucleus $^{208}$Pb. Nuclear moments of isotopes close to this doubly magic nucleus are good tests for the theoretic models. Besides pushing the models to their limits, the nuclear moments of $^{211}$Po also yield new information on the f...

  17. Polonium 210 and lead 210 in Syrian sea and lake fish and the dose due to their intake

    International Nuclear Information System (INIS)

    Al-Masri, M.S.; Mamish, S.; Budeir, Y.; Nashwaty, A.

    1998-09-01

    Edible part of 36 types of sea fish collected from local market (Lattakia, Tartus, Banias) and seven types of river fish (Euphrate river and Mzerib lake) have been analyzed for 210 Po and 210 Pb. Results of analysis have shown that 210 Po and 210 Pb concentrations in sea fish varied between 0.27 and 27.48 Bq/kg and between 0.05 and 0.38 Bq/kg, respectively while for river fish concentrations were relatively low and varied between 0.61 and 3.08 Bq/kg for 210 Po and between 0.04 and 0.10 Bq/kg for 210 Pb. In addition, the Syrian adults daily intakes of 210 Po and 210 Pb have been estimated and found to be 6.0 and 0.24 mBq respectively. These intakes are much less than those reported in other areas in the world. The collective dose was also determined and found to be about 5.09 man.Sv for polonium 210 and 2.93 man.Sv for lead 210 . (author)

  18. The effect of preparation processes on polonium 210 transfer from tea and mate leaves to aqueous extract

    International Nuclear Information System (INIS)

    Al-Masri, M. S.; Nashawati, A.; Amin, Y.; Al-Akel, B.

    2002-08-01

    Polonium 210 was determined in 34 kinds of tea samples and 8 kinds of mate samples collected from the local market. The results have shown that the activities of 210 Po in tea and meta samples were relatively high and varied between 5.5 and 39 Bq.Kg -1 , and 47 to 82 Bq.Kg -1 in tea and mate samples respectively. In order to estimate the annual intake of 210 Po by drinking of the aqueous extract of these materials, preparation processes of the leaves were performed at different conditions (temperature, duration of soaking). The results have shown that the amount of 210 Po transferred to the aqueous extract varied between 9 and 21% and 3 and 15% for tea leaves and mate respectively. There was a clear variations in the soluble amount according to the applied different conditions of soaking. The annual intake of 210 Po due to drinking tea and meta extracts was calculated and found to be 9 Bq.year -1 and 151 Bq.year -1 for tea and mate respectively. (author)

  19. The significance of lead-210, polonium-210 and protactinium-231 in emissions from coal-fired power stations: a comparison with natural environmental sources

    International Nuclear Information System (INIS)

    Corbett, J.O.

    1981-04-01

    Recently published calculations have suggested that a hypothetical individual may receive an effective radiation dose equivalent of 23 mrem/y from coal-fired power station emissions through the ingestion of lead-210, polonium-210 and protactinium-231. It is shown that the model used in those calculations is over-pessimistic by one or two orders of magnitude when applied to the deposition of Pb-210 and Po-210 derived from the decay of radon naturally present in the atmosphere. A more recent assessment of metabolic data for Pa-231 suggests that estimated doses from this nuclide also can be reduced by about a factor of twenty. It is concluded that the maximum effective dose equivalent from power station emissions probably does not exceed 1-2 mrem/y. (author)

  20. Preparation of a Strong Thin Polonium Source And Preliminary Experiments on the Yield of (α,n) Reactions

    International Nuclear Information System (INIS)

    Broda, E.

    1945-01-01

    This report was written by E. Broda and P. K. Wright at the Cavendish Laboratory (Cambridge) in July 1945 and is about the preparation of a strong thin polonium source and preliminary experiments on the yield of (alpha,n) reactions. This report includes the experiment description, the discussion of the results and consist of 4 parts: (1) the electrode position of polonium under different conditions (2) a standard procedure for preparation of strong thin Po sources (3) a simple method for the recovery of RaD from complex mixtures (4) some preliminary experiments with a Po source. (nowak)

  1. Preparation of a Strong Thin Polonium Source And Preliminary Experiments on the Yield of (α,n) Reactions

    Energy Technology Data Exchange (ETDEWEB)

    Broda, E.

    1945-07-01

    This report was written by E. Broda and P. K. Wright at the Cavendish Laboratory (Cambridge) in July 1945 and is about the preparation of a strong thin polonium source and preliminary experiments on the yield of (alpha,n) reactions. This report includes the experiment description, the discussion of the results and consist of 4 parts: (1) the electrode position of polonium under different conditions (2) a standard procedure for preparation of strong thin Po sources (3) a simple method for the recovery of RaD from complex mixtures (4) some preliminary experiments with a Po source. (nowak)

  2. Determination of polonium 210 in different types of tobacco consumed in Sudan

    International Nuclear Information System (INIS)

    Abdulrahman, M. E.

    2011-01-01

    The carcinogenic effect of 210 Po with respect to lung cancer is an important problem in many countries with very high cigarette consumption. Sudan is one of the consumptions of cigarettes in the world. The aim of this study was the determination polonium-210 in different parts of tobacco plant comes from China and Brazil consumed in cigarette in Sudan and determination of 210 Po in five most frequently smoked brands more consumption in Sudan. The annual committed effective dose from cigarette was determined and comparison with other results reported in literature. The tobacco plant (leaves and root) for analysis were collected from Haggar factory in Sudan and another brand were collected randomly from markets, only the most popular one was chosen for analysis (Bringi, Lord, Winner, Goal, Benson). The polonium-210 activity was measured on an alpha-spectrometer equipped with semiconductor surface barrier silicon detectors after spontaneously plated onto asilver disc from hydrochloric acid medium. Polonium samples were measured for 2-3 days. The accuracy and precision of radiochemical method were evaluated using (IAEA-326). The values of activity concentration of 210 Po found in cigarettes consumed in Sudan are within of the range of values found in the literature. The 210 Po presented concentration in different brands ranging from 22.8 to 51.6 Bqkg -1 (average 36.54 Bq kg -1 ). The activity concentration of 210 Po in popular brand cigarette tobacco is higher than that in fine brand cigarette tobacco. Found the highest concentration in the raw material compared to the final product is attributed that to the import, storage and manufacturing processes. Activity determination indicates those cigarettes consumed in Sudan are comparable to the values reported in China and Brazil that the raw material comes from these two countries. The polonium is non-uniformly distributed within the tobacco plants analyzed in this study, the highest levels were found in the leaves

  3. Polonium release from an ATW burner system with liquid lead-bismuth coolant

    International Nuclear Information System (INIS)

    Li, N.; Yefimov, E.; Pankratov, D.

    1998-04-01

    The authors analyzed polonium release hazards in a conceptual pool-type ATW burner with liquid lead-bismuth eutectic (LBE) coolant. Simplified quantitative models are used based on experiments and real NPP experience. They found little Po contamination outside the burner under normal operating conditions with nominal leakage from the gas system. In sudden gas leak and/or coolant spill accidents, the P contamination level can reach above the regulation limit but short exposure would not lead to severe health consequences. They are evaluating and developing mitigation methods

  4. Determination of polonium 210 in different types of tobacco consumed in Sudan

    Energy Technology Data Exchange (ETDEWEB)

    Abdulrahman, M E [Sudan Academy of Sciences, Atomic Energy Council, Khartoum (Sudan)

    2011-01-15

    The carcinogenic effect of {sup 210} Po with respect to lung cancer is an important problem in many countries with very high cigarette consumption. Sudan is one of the consumptions of cigarettes in the world. The aim of this study was the determination polonium-210 in different parts of tobacco plant comes from China and Brazil consumed in cigarette in Sudan and determination of {sup 210} Po in five most frequently smoked brands more consumption in Sudan. The annual committed effective dose from cigarette was determined and comparison with other results reported in literature. The tobacco plant (leaves and root) for analysis were collected from Haggar factory in Sudan and another brand were collected randomly from markets, only the most popular one was chosen for analysis (Bringi, Lord, Winner, Goal, Benson). The polonium-210 activity was measured on an alpha-spectrometer equipped with semiconductor surface barrier silicon detectors after spontaneously plated onto asilver disc from hydrochloric acid medium. Polonium samples were measured for 2-3 days. The accuracy and precision of radiochemical method were evaluated using (IAEA-326). The values of activity concentration of {sup 210} Po found in cigarettes consumed in Sudan are within of the range of values found in the literature. The {sup 210} Po presented concentration in different brands ranging from 22.8 to 51.6 Bqkg{sup -1}(average 36.54 Bq kg{sup -1}). The activity concentration of {sup 210} Po in popular brand cigarette tobacco is higher than that in fine brand cigarette tobacco. Found the highest concentration in the raw material compared to the final product is attributed that to the import, storage and manufacturing processes. Activity determination indicates those cigarettes consumed in Sudan are comparable to the values reported in China and Brazil that the raw material comes from these two countries. The polonium is non-uniformly distributed within the tobacco plants analyzed in this study, the highest

  5. Plutonium and polonium concentrations in the different water masses crossing the Strait of Gibraltar

    International Nuclear Information System (INIS)

    Gasco, C.; Anton, M.P.

    1999-01-01

    In this paper total Pu and Po concentrations in the water column are presented as part of a study to determine the exchange fluxes and overall budget of these selected nuclides within the Atlantic and Mediterranean basins. Polonium is a natural radionuclide continuously input to the sea via atmospheric deposition from the radon existing in the air. Plutonium is a man-made radionuclide that was mostly introduced in the atmosphere during the 60's nuclear testing. Since then, it has been gradually disappearing due to fallout and the banning of nuclear atmospheric explosions

  6. Particulate uranium, plutonium and polonium in the biogeochemistries of the coastal zone

    Energy Technology Data Exchange (ETDEWEB)

    Hodge, V F; Koide, M; Goldberg, E D [Scripps Institution of Oceanography, La Jolla, CA (USA)

    1979-01-18

    It is stated that although increasing attention has been paid to the role of inorganic solid phases in the chemistry of seawater, little quantitative data has been available to assess their involvement with living systems. Recent observations are here reported on the uptake of uranium, plutonium and polonium in coastal waters by organisms and submerged surfaces as traced by their isotopes. It is shown that the body burdens of these radioelements in some marine organisms are governed measurably by the uptake of their particulate forms. Furthermore, these elements are associated with different particulate phases, as deduced from the rates at which they deposit on submerged surfaces.

  7. Comparative uptake of thorium-230, radium-226, lead-210 and polonium-210 by plants

    Energy Technology Data Exchange (ETDEWEB)

    D' Souza, T J; Mistry, K B

    1970-01-01

    The entry and translocation of /sup 230/thorium, /sup 226/radium, /sup 210/lead, and /sup 210/polonium were examined in nutrient culture experiments. Strontium-89 was included for comparison. Red kidney beans (Phaseolus vulgaris L.) were treated for a period of 15 days. Results indicate that accumulation of /sup 230/thorium, /sup 210/lead and /sup 210/polonium occurs predominantly in roots and only very small amounts of these nuclides are translocated to shoots. Over comparable periods, the accumulation of /sup 226/radium in roots is 2-3 times lower than that of the other nuclides of uranium series. However, the most significant difference between /sup 226/radium and other nuclides is in the extent of their upward transport which for radium is 50-200 times greater. The amount of radium translocated to shoots is comparable to that of strontium. The present evidence of rapid transfer of /sup 226/radium to shoots suggests that among the nuclides examined, /sup 226/radium is likely to make the major contribution to radioactivity in aerial tissues of plants grown under conditions where root absorption is the principal route of entry of the nuclides.

  8. Determination of uranium and polonium in Spa rus aura ta by alpha spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Luna P, M.; Renteria, M.; Montero C, M. E. [Centro de Investigacion en Materiales Avanzados, S. C., Miguel de Cervantes No. 120, Complejo Industrial Chihuahua, 31109 Chihuahua (Mexico); Manjon C, G.; Diaz, I., E-mail: elena.montero@cimav.edu.mx [Universidad de Sevilla, Escuela Tecnica Superior de Arquitectura, Departamento de Fisica Aplicada II, San Fernando No. 4, 41004 Sevilla (Spain)

    2012-06-15

    The aim of this study was optimizing conditions for the specific activities determination of some uranium-series radionuclides present in Spa rus aura ta by alpha spectrometry. Determinations of specific activities were conducted varying the type of digestion: acid attack on hot plate, controlled microwave digestion and acid attack after calcination of the sample. The latter procedure was applied only to the case of uranium isotopes determination. The variation in the isotope extraction method consisted of applying the techniques of liquid-liquid extracting using Tributyl phosphate or chromatographic UTEVA resin. Results depending on the type of treatment given to the samples were compared based on obtained chemical yields. The results reveal a higher bioaccumulation of polonium in the liver sample, with activities of 0.809, 2.495 and 2.439 Bq kg{sup -1} fresh wt compared with the fillet. The best chemical yields of polonium were close to 60% for samples that were digested by microwave. In the case of uranium the best chemical yields, close to 80% for fillet, were obtained with a previous calcination of the sample and using the UTEVA resin. (Author)

  9. Determination of uranium and polonium in Spa rus aura ta by alpha spectrometry

    International Nuclear Information System (INIS)

    Luna P, M.; Renteria, M.; Montero C, M. E.; Manjon C, G.; Diaz, I.

    2012-01-01

    The aim of this study was optimizing conditions for the specific activities determination of some uranium-series radionuclides present in Spa rus aura ta by alpha spectrometry. Determinations of specific activities were conducted varying the type of digestion: acid attack on hot plate, controlled microwave digestion and acid attack after calcination of the sample. The latter procedure was applied only to the case of uranium isotopes determination. The variation in the isotope extraction method consisted of applying the techniques of liquid-liquid extracting using Tributyl phosphate or chromatographic UTEVA resin. Results depending on the type of treatment given to the samples were compared based on obtained chemical yields. The results reveal a higher bioaccumulation of polonium in the liver sample, with activities of 0.809, 2.495 and 2.439 Bq kg -1 fresh wt compared with the fillet. The best chemical yields of polonium were close to 60% for samples that were digested by microwave. In the case of uranium the best chemical yields, close to 80% for fillet, were obtained with a previous calcination of the sample and using the UTEVA resin. (Author)

  10. In-source laser spectroscopy of polonium isotopes: From atomic physics to nuclear structure

    CERN Multimedia

    Rothe, S

    2014-01-01

    The Resonance Ionization Laser Ion Source RILIS [1] at the CERN-ISOLDE on-line radioactive ion beam facility is essential for ion beam production for the majority of experiments, but it is also powerful tool for laser spectroscopy of rare isotopes. A series of experiments on in-source laser spectroscopy of polonium isotopes [2, 3] revealed the nuclear ground state properties of 191;211;216;218Po. However, limitations caused by the isobaric background of surface-ionized francium isotopes hindered the study of several neutron rich polonium isotopes. The development of the Laser Ion Source and Trap (LIST) [4] and finally its integration at ISOLDE has led to a dramatic suppression of surface ions. Meanwhile, the RILIS laser spectroscopy capabilities have advanced tremendously. Widely tunable titanium:sapphire (Ti:Sa) lasers were installed to complement the established dye laser system. Along with a new data acquisition system [5], this more versatile laser setup enabled rst ever laser spectroscopy of the radioact...

  11. Determination of uranium and thorium isotopes and polonium in sediment profiles from Baixada Santista, SP

    International Nuclear Information System (INIS)

    Ramos, Guilherme da Franca

    2010-01-01

    The objective of the present work is to determine the activity concentration of uranium and thorium isotopes and polonium in estuarine sediments from Baixada Santista. The area comprehends nine cities in the Brazilian coast (Bertioga, Guaruja, Santos, Sao Vicente, Cubatao, Praia Grande, Mongagua, Itanhaem and Peruibe). It is one of the most important industrial areas in Brazil due to the large number of industries operating in Cubatao, such as steel, petrochemical and fertilizer industries. That, together with a large population, causes a negative impact on the marine biota. In the present work 10 profiles of sediment cores, with depth varying from 41 to 98 cm, were analyzed. The cores were obtained from Santos, Cubatao, Sao Vicente and Bertioga. The cores were sliced every 2 cm and were treated with both physical and chemical processes, including drying, grinding and sieving. The samples were dissolved by acid digestion, till total dissolution and destruction of organic matter. After the acid digestion, the samples were filtered and evaporated till dryness. The radiochemical techniques used to separate the radionuclides and to prepare the final source for alpha counting were ion exchange chromatography and spontaneous deposition for polonium and electrodeposition for U and Th. The final sources were counted in a surface barrier alpha spectrometer. Values obtained for the radionuclides analyzed were similar to the activity concentrations of sediments in non polluted areas, with the exception of a few samples that showed anthropic influence. (author)

  12. Deformation and mixing of co-existing shapes in the neutron-deficient polonium isotopes

    CERN Document Server

    AUTHOR|(CDS)2078559; Huyse, Mark

    The neutron-deficient polonium isotopes, with only 2 protons outside the Z = 82 shell closure, are situated in an interesting region of the nuclear chart. In the neighboring lead (Z = 82) and mercury (Z = 80) isotopes, experimental and theoretical efforts identified evidence of shape coexistence. Shape coexistence is the remarkable phenomenon in which two or more distinct types of deformation occur in states of the same angular momentum and similar excitation energy in a nucleus. The neutron-deficient polonium isotopes have also been studied intensively, experimentally as well as theoretically. The closed neutron-shell nucleus 210Po (N = 126) manifests itself as a two-particle nucleus where most of the excited states can be explained by considering the degrees of freedom of the two valence protons outside of 208Pb. The near-constant behavior of the yrast 2+1 and 4+1 states in the isotopes with mass 200 ≤ A ≤ 208 can be explained by coupling the two valence protons to a vibrating lead core. 200Po seems to ...

  13. Evidence towards improved estimation of respiratory muscle effort from diaphragm mechanomyographic signals with cardiac vibration interference using sample entropy with fixed tolerance values.

    Directory of Open Access Journals (Sweden)

    Leonardo Sarlabous

    Full Text Available The analysis of amplitude parameters of the diaphragm mechanomyographic (MMGdi signal is a non-invasive technique to assess respiratory muscle effort and to detect and quantify the severity of respiratory muscle weakness. The amplitude of the MMGdi signal is usually evaluated using the average rectified value or the root mean square of the signal. However, these estimations are greatly affected by the presence of cardiac vibration or mechanocardiographic (MCG noise. In this study, we present a method for improving the estimation of the respiratory muscle effort from MMGdi signals that is robust to the presence of MCG. This method is based on the calculation of the sample entropy using fixed tolerance values (fSampEn, that is, with tolerance values that are not normalized by the local standard deviation of the window analyzed. The behavior of the fSampEn parameter was tested in synthesized mechanomyographic signals, with different ratios between the amplitude of the MCG and clean mechanomyographic components. As an example of application of this technique, the use of fSampEn was explored also in recorded MMGdi signals, with different inspiratory loads. The results with both synthetic and recorded signals indicate that the entropy parameter is less affected by the MCG noise, especially at low signal-to-noise ratios. Therefore, we believe that the proposed fSampEn parameter could improve estimates of respiratory muscle effort from MMGdi signals with the presence of MCG interference.

  14. Absorption of environmental polonium-210 by the human gut

    International Nuclear Information System (INIS)

    Hunt, G.J.; Allington, D.J.

    1993-01-01

    Current values for the gut absorption factor of plutonium- 210 ( 210 Po) are based on very few human data, yet the dose due to 210 Po is an important component of the dose to man through food as a result of natural sources of radiation. In this study, three male and three female adult volunteers ate supplies of brown crab meat containing natural concentrations of 210 Po, which are analysed from sub-samples. Daily urine and faecal samples, taken for 3 days before and up to 3 weeks after ingestion, were also analysed. Values of apparent absorption were derived from the faecal measurements; estimates of the true absorption were derived taking account of endogenous faecal excretion on the basis of existing data for intravenous administration. The results appear to suggest that the gut absorption factor in current use for 210 Po (in connection with ingestion in food) should be increased from 0.1-03 to about 0.8. The implications for estimates of dose due to this exposure pathway are noted. (author)

  15. Absorption of environmental polonium-210 by the human gut

    Energy Technology Data Exchange (ETDEWEB)

    Hunt, G J; Allington, D J [Ministry of Agriculture, Fisheries and Food, Lowestoft (United Kingdom). Fisheries Radiobiological Lab.

    1993-06-01

    Current values for the gut absorption factor of plutonium- 210 ([sup 210]Po) are based on very few human data, yet the dose due to [sup 210]Po is an important component of the dose to man through food as a result of natural sources of radiation. In this study, three male and three female adult volunteers ate supplies of brown crab meat containing natural concentrations of [sup 210]Po, which are analysed from sub-samples. Daily urine and faecal samples, taken for 3 days before and up to 3 weeks after ingestion, were also analysed. Values of apparent absorption were derived from the faecal measurements; estimates of the true absorption were derived taking account of endogenous faecal excretion on the basis of existing data for intravenous administration. The results appear to suggest that the gut absorption factor in current use for [sup 210]Po (in connection with ingestion in food) should be increased from 0.1-03 to about 0.8. The implications for estimates of dose due to this exposure pathway are noted. (author).

  16. Polonium-210 and lead-210 in marine organisms

    International Nuclear Information System (INIS)

    Yamamoto, M.; Kuwabara, J.; Komura, K.; Ueno, K.

    1994-01-01

    The concentrations of 210 Po and 210 Pb were determined in about 30 species of marine organisms collected mainly from the north-eastern region of Japan to know the levels and distributions of these radionuclides and to estimate their intake levels from marine foods. 210 Po and 210 Pb showed a wide range of concentration in species: 0.6-26 and 0.04-0.54 Bq/kg (wet wt) in fishes, 0.5-220 and 0.2-43 Bq/kg (wet wt) in molluscs, echinoderms and chordatas, and 2.8-4.3 and 0.4-1.3 Bq/kg (wet wt) in algae, respectively. Higher accumulation of 210 Po relative to 210 Pb was found in all of the samples analyzed. The intake levels of 210 Po and 210 Pb by marine foods consumption were roughly estimated to be 0.48-0.69 and 0.022-0.042 Bq/d per person, respectively, on the basis of the statistical data on the consumption of seafood and/or production rates of marine foods. (author) 16 refs.; 6 tabs

  17. Fetal doses from plutonium-239 and polonium-210

    International Nuclear Information System (INIS)

    Harrison, J.D.; Morgan, A.; Stather, J.W.

    1992-01-01

    The transfer of 239 Pu and 210 Po from the maternal circulation to the developing embryo and fetus was studied in rodents. The highest concentrations of both isotopes were measured in the yolk sac. In utero doses to haemopoietic tissue have been calculated taking account of transfer to the blastocyst/egg cylinder, yolk sac, liver and bone marrow. From animal data, the concentration ratios relative to maternal liver for these tissues were taken to be 0.1, 2, 0.01 and o.02, respectively for 239 Pu; and 1, 2, 0.1 and 0.1, respectively, for 210 Po. These concentration ratios were applied to periods of human gestation of 0-2.5 weeks, 2.5-6 weeks, 6-12 weeks and 12-38 weeks, and used to calculate fetal tissue doses for chronic maternal intake by ingestion of 1 kBq 239 Pu or 2 kBq 210 Po in the year of pregnancy (1 ALI for a member of the public). On this basis, the total in utero dose to haemopoietic tissue was about 1 μSv from 239 Pu and 60 μSv from 210 Po compared with red bone marrow doses to the mother in the year of 19 μSv from 239 Pu and 160 μSv from 210 Po. The yolk sac and bone marrow dominated in utero doses from both nuclides. For 239 Pu, because of its long half life, an important consideration was activity present in the offspring at birth and committed dose equivalents to red bone marrow in the child and mother. The total dose to haemopoietic tissue in the offspring to age 70 years, including in utero doses, was calculated as 13 μSv compared with a maternal dose to red bone marrow of 1400 μSv. For both isotopes the risk of leukaemia in the year of pregnancy was estimated to be of the same order for mother and fetus. For 239 Pu, the overall risk to 70 years of age was two orders of magnitude higher for the mother than her offspring. For 239 Pu, an acute intake of 1 kBq by ingestion during the period of yolk sac haemopoiesis would result in the highest in utero dose, estimated at about 20 μSv. However, activity at birth would be lower and the overall

  18. Polonium-210 in the total environment of Goa

    International Nuclear Information System (INIS)

    Avadhani, D.N.; Mahesh, H.M.; Siddappa, K.

    2007-01-01

    The paper deals with the distribution of 210 Po in total environment of Goa. The activity concentration of 210 Po in food, diet, water and air samples of the region were measured and the annual effective dose due to ingestion of this radionuclide was estimated. The activity of 210 Po in soil and sand samples vary from 3.2 Bq kg -1 to 186.2 Bq kg -1 with a mean value of 57.4Bq kg -1 and from 0.94 Bq kg -1 to 3.7 Bq kg -1 with the mean value of 1.8 Bq kg -1 respectively. Among food samples fish and prawn shows higher concentration of 210 Po. The Committed Effective Dose Equivalent due to ingestion of non veg meal, veg meal, breakfast and potable water were found to be 94.6 μSv y -1 , 49.1 μSv y -1 , 10.5 μSv y -1 and 4.2 μSv y -1 respectively. All the results are compared with the reported literature values and discussed in detail in this paper. (author)

  19. Polonium-210 and lead-210 in marine food chains

    International Nuclear Information System (INIS)

    Heyraud, M.; Cherry, R.D.

    1979-01-01

    210 Po and 210 Pb have been measured systematically in whole animals, muscle and hepatopancreas of crustaceans and of molluscan cephalopods representative of a pelagic and benthic food chain. The same nuclides were also measured in liver, pyloric caecum, stomach contents and muscle of tuna. The concentration factors from sea water to whole animals were approximately constant along both food chains, being of the order of 10 4 for 210 Po and 10 2 for 210 Pb. The highest concentration factors were found in shrimp of the genus Sergestes. In muscle, the concentration factors were an order of magnitude less; in the hepatopancreas, they were an order of magnitude higher, reaching 10 6 in shrimp of the genus Sergestes. Such concentrations imply alpha-radiation doses of the order of 10 rem per year and more in this organ, which contains about 50 to 90% of the 210 Po in the whole animal in the 11 species analyzed. A detailed study of the intracellular behaviour of 210 Po in the hepatopancreas is clearly indicated. 210 Po can be used as a sensitive natural tracer in biological systems. Thus, feeding Meganyctiphanes norvegica in the laboratory on food low in 210 Po led to an approximate value of about 6 1/2 days for the biological half-life of 210 Po in the hepatopancreas of this euphausiid. Furthermore, the data on 210 Po and 210 Pb in the cephalopod hepatopancreas allowed the time of conservation of frozen squid which had been bought at the market to be estimated. (orig.) 891 AJ/orig. 892 MKO [de

  20. Polonium-210 and lead-210 in marine food chains

    Energy Technology Data Exchange (ETDEWEB)

    Heyraud, M [Musee Oceanographique (Monaco). International Lab. of Marine Radioactivity; Cherry, R D [Cape Town Univ. (South Africa). Dept. of Physics

    1979-01-01

    /sup 210/Po and /sup 210/Pb have been measured systematically in whole animals, muscle and hepatopancreas of crustaceans and of molluscan cephalopods representative of a pelagic and benthic food chain. The same nuclides were also measured in liver, pyloric caecum, stomach contents and muscle of tuna. The concentration factors from sea water to whole animals were approximately constant along both food chains, being of the order of 10/sup 4/ for /sup 210/Po and 10/sup 2/ for /sup 210/Pb. The highest concentration factors were found in shrimp of the genus Sergestes. In muscle, the concentration factors were an order of magnitude less; in the hepatopancreas, they were an order of magnitude higher, reaching 10/sup 6/ in shrimp of the genus Sergestes. Such concentrations imply alpha-radiation doses of the order of 10 rem per year and more in this organ, which contains about 50 to 90% of the /sup 210/Po in the whole animal in the 11 species analyzed. A detailed study of the intracellular behaviour of /sup 210/Po in the hepatopancreas is clearly indicated. /sup 210/Po can be used as a sensitive natural tracer in biological systems. Thus, feeding Meganyctiphanes norvegica in the laboratory on food low in /sup 210/Po led to an approximate value of about 6 1/2 days for the biological half-life of /sup 210/Po in the hepatopancreas of this euphausiid. Furthermore, the data on /sup 210/Po and /sup 210/Pb in the cephalopod hepatopancreas allowed the time of conservation of frozen squid which had been bought at the market to be estimated. (orig.) 891 AJ/orig. 892 MKO.

  1. Celebration of the radium and polonium discovery as a promotion of nuclear energy in Poland

    International Nuclear Information System (INIS)

    Latek, Stanislaw

    1998-01-01

    The radium and polonium discovery centennial was inaugurated in April 1997. The first event was a Polish-French show of scientific documentary movies on the uses of ionizing radiation and nuclear power. A symposium Radiation - History and Modern Times was organized in spring 1997. Many other interesting events were held throughout 1997. Warsaw hosted an interesting exhibition 'From the Radium Needle to the Medical Accelerators'. A seminar and an exhibition on Radiation Technique in Environmental Protection were organized in cooperation with the IAEA. The Council for Atomic Energy initiated and conducted a workshop on Radioactivity - Risk and Hope. The Polish Academy of Science and the Society of Nuclear Medicine organised a symposium on Polonium and Radium Discovery Impact on Medicine, Radiation Protection and Medical Industry. The National Atomic Energy was the initiator of film shows held for school youth, which turned out to be a great success. The youngsters, mainly from schools bearing the name of Marie Curie, had an opportunity to see films about the great scientist and her discoveries, and on the very phenomenon of radiation. They also had a chance to visit Maria research reactor in the Institute of Atomic Energy in Swierk. Now, at the beginning of February 1998, a three-day scientific session is being held in Warsaw, to commemorate the radium and polonium discovery. Many other events will take place in the coming months. In particular, June 1998, an international conference on Nuclear Physics Close to the Barriers will be held. Another conference, closing the centennial sponsored by UNESCO will focus on the Scientific and Philosophical Consequences of Discovery of Plutonium and Radium, Benefits and Threats to Mankind. Public opinion polls, similar to those conducted in 1996, are planned for spring 1998. The 1996 polls, conducted 10 years after the Chernobyl accident, showed that the majority of Poles feared ionizing radiation and opposed the nuclear power

  2. Evaluation of the contribution of smoking to total blood polonium-210 in Saudi population

    Energy Technology Data Exchange (ETDEWEB)

    Shabana, E.I. E-mail: eshabana@kacst.edu.sa; Elaziz, M.A. Abd; Al-Arifi, M.N.; Al-Dhawailie, A.A.; Al-Bokari, M.M-A

    2000-01-01

    A preliminary study of {sup 210}Po concentrations in the blood of some smokers and nonsmokers is presented in order to evaluate the contribution of smoking to total blood {sup 210}Po in Saudi population. Blood samples were collected from 30 volunteers and analyzed by high resolution {alpha}-spectrometry using a radiochemical technique. The technique is based on the separation of polonium from other components of the sample by wet ashing with an HNO{sub 3}/H{sub 2}O{sub 2} oxidizing mixture and spontaneous deposition on a silver disc under the relevant conditions for {alpha}-particle counting. The results indicated that a significant fraction (about 30%) of blood {sup 210}Po is related to smoking.

  3. The particulate material formed during the combusion of polonium and plutonium

    Energy Technology Data Exchange (ETDEWEB)

    Stewart, K.

    1963-11-15

    Over the last decade the production and use of uranium, plutonium and other radioactive materials has developed steadily. The work described in this paper is part of a reasonably comprehensive study of the extent and seriousness of the radiological hazards which could occur as the result of selected types of accidents. Additionally, these studies demonstrate the types of material and operations which are the more likely to produce a serious situation should a mishap occur. The emphasis in the paper, therefore, is on the differences between an element, polonium, of high specific activity which is volatile, and a reactive material, plutonium, of lower specific activity which is non-volatile but of somewhat greater radiotoxicity. The modes of formation of oxide aerosols from these two elements are, to a very considerable degree, representative of two important and contrasting processes.

  4. Bioaccumulation of polonium-210 in fish of the Kaveri river system

    International Nuclear Information System (INIS)

    Shaheed, K.; Shahul Hameed, P.; Iyengar, M.A.R.

    1997-01-01

    Concentration of naturally occurring radioactive nuclide polonium-210 was determined in selected species of fish from the Kaveri river system at Tiruchirappalli. It is shown that 210 Po is non-uniformly distributed within these fishes. Concentrations of 210 Po in the muscle of fish ranged from 3.3 to 8.2 Bq/kg (wet weight). Concentration factors of Po 210 in edible portion of fish from river water worked out to be 2.5 x 10 3 to 6.3 x 10 3 . Radiation dose to public due to consumption of fish from the Kaveri river varied from 5.1 to 27.3 μSv/y. The results have implications that fish represents an important source of supply of 210 Po to humans. (author). 16 refs., 2 tabs

  5. A faster sample preparation method for determination of polonium-210 in fish

    International Nuclear Information System (INIS)

    Sadi, B.B.; Jing Chen; Kochermin, Vera; Godwin Tung; Sorina Chiorean

    2016-01-01

    In order to facilitate Health Canada’s study on background radiation levels in country foods, an in-house radio-analytical method has been developed for determination of polonium-210 ( 210 Po) in fish samples. The method was validated by measurement of 210 Po in a certified reference material. It was also evaluated by comparing 210 Po concentrations in a number of fish samples by another method. The in-house method offers faster sample dissolution using an automated digestion system compared to currently used wet-ashing on a hot plate. It also utilizes pre-packed Sr-resin® cartridges for rapid and reproducible separation of 210 Po versus time-consuming manually packed Sr-resin® columns. (author)

  6. Determination of the electron affinity of astatine and polonium by laser photodetachment

    CERN Multimedia

    We propose to conduct the first electron affinity (EA) measurements of the two elements astatine (At) and polonium (Po). Collinear photo-detachment spectroscopy will allow us to measure these quantities with an uncertainty limited only by the spectral line width of the laser. We plan to use negative ion beams of the two radioactive elements At and Po, which are only accessible on-line and at ISOLDE. The feasibility of our proposed method and the functionality of the experimental setup have been demonstrated at ISOLDE in off-line tests by the clear observation of the photo-detachment threshold for stable iodine. This proposal is based on our Letter of Intent I-148.

  7. Induction of the lambda bacteriophage synthesis in Escherichia coli K 12 by polonium alpha rays

    International Nuclear Information System (INIS)

    Devoret, Raymond

    1958-06-01

    This research thesis reports the study of the inducing action of polonium alpha radiations in Escherichia Coli K 12 by using an external irradiation device. This work comprised the development of a method to spread bacteria in layer with a thickness less than 20 microns, and the measurement of the number of α particles falling on the irradiated surface. This measurement has been performed by using a nuclear emulsion and a simple photographic film. It appears that alpha radiations have an inducing action, and that at most 15 per cent of bacteria can be induced. The comparison of the induction curve with the survival curves of lysogen and sensitive stains shows that there is no abortive induction. Thus, it appears that this inducing action is not due to an indirect effect of the irradiated medium [fr

  8. Study of polonium isotopes ground state properties by simultaneous atomic- and nuclear-spectroscopy

    CERN Multimedia

    Koester, U H; Kalaninova, Z; Imai, N

    2007-01-01

    We propose to systematically study the ground state properties of neutron deficient $^{192-200}$Po isotopes by means of in-source laser spectroscopy using the ISOLDE laser ion source coupled with nuclear spectroscopy at the detection setup as successfully done before by this collaboration with neutron deficient lead isotopes. The study of the change in mean square charge radii along the polonium isotope chain will give an insight into shape coexistence above the mid-shell N = 104 and above the closed shell Z = 82. The hyperfine structure of the odd isotopes will also allow determination of the nuclear spin and the magnetic moment of the ground state and of any identifiable isomer state. For this study, a standard UC$_{x}$ target with the ISOLDE RILIS is required for 38 shifts.

  9. The Hamburg polonium-210 case. Monitoring of internal contaminations in a malevolent act

    International Nuclear Information System (INIS)

    Dalheimer, A.; Koenig, K.; Nosske, D.; Schaefer, I.

    2009-01-01

    The dead of Alexander Litvinenko in London in the late 2006 was linked with the visit of Dimitri Kovtun. So an investigation was started by the Hamburg Police. As the presence of polonium-210 was uncertain, the action was supported by the Federal Defense against Nuclear Hazards (NGA) of the Federal Office for Radiation Protection (BfS). Radiation measurements in some flats in Hamburg confirmed the suspicion of polonium-210 contaminations. As incorporations by ingestion or inhalation could not generally be excluded, the Coordinating Office on Incorporation Monitoring of the BfS (Leitstelle Inkorporationsueberwachung des BfS) was requested to clarify this issue. The BfS office then coordinated the required bioassay analyses of urine samples carried out at four officially appointed in-vitro laboratories for incorporation monitoring. The group of people to be examined included the members of the family involved living in the contaminated flats, the emergency forces, as well as potentially exposed members of the public. The calculation of the internal dose was based on standard assumptions and also conducted by the BfS. The internal radiation doses proved to be within the range of radiation doses due to natural exposures. Retrospectively it should be stressed that the collaboration and cooperation of all institutions involved in the operation in Hamburg was extremely good despite their differing organisational structures. As a result of the incident in Hamburg various middle and long-term measures have been taken since then by the BfS Coordinating Office on Incorporation Monitoring. (orig.)

  10. Polonium 210Po activities in human blood of patients with ischaemic heart disease from Gdansk in Poland

    International Nuclear Information System (INIS)

    Alicja Borylo; Bogdan Skwarzec; Grzegorz Romanczyk; Janusz Siebert

    2013-01-01

    The determination of polonium 210 Po in human blood samples is presented and discussed in this paper. The human blood samples were collected from patients of Medical University of Gdansk with ischaemic heart disease (morbus ischaemicus cordis, MIC). The polonium concentrations in analyzed human blood samples are very differentiated. 210 Po is of particular interest in public health and although is present in the environment in extremely low amounts, it is easily bioaccumulated to the human body. The study shows that the amount of 210 Po that is incorporated into the human body depends on the food habits and some difference in its levels could be observed between smokers and non-smokers. (author)

  11. Polonium 210Po activities in human blood of patients with ischaemic heart disease from Gdańsk in Poland.

    Science.gov (United States)

    Boryło, Alicja; Skwarzec, Bogdan; Romańczyk, Grzegorz; Siebert, Janusz

    The determination of polonium 210 Po in human blood samples is presented and discussed in this paper. The human blood samples were collected from patients of Medical University of Gdańsk with ischaemic heart disease ( morbus ischaemicus cordis , MIC ). The polonium concentrations in analyzed human blood samples are very differentiated. 210 Po is of particular interest in public health and although is present in the environment in extremely low amounts, it is easily bioaccumulated to the human body. The study shows that the amount of 210 Po that is incorporated into the human body depends on the food habits and some difference in its levels could be observed between smokers and non-smokers.

  12. MATLAB-implemented estimation procedure for model-based assessment of hepatic insulin degradation from standard intravenous glucose tolerance test data.

    Science.gov (United States)

    Di Nardo, Francesco; Mengoni, Michele; Morettini, Micaela

    2013-05-01

    Present study provides a novel MATLAB-based parameter estimation procedure for individual assessment of hepatic insulin degradation (HID) process from standard frequently-sampled intravenous glucose tolerance test (FSIGTT) data. Direct access to the source code, offered by MATLAB, enabled us to design an optimization procedure based on the alternating use of Gauss-Newton's and Levenberg-Marquardt's algorithms, which assures the full convergence of the process and the containment of computational time. Reliability was tested by direct comparison with the application, in eighteen non-diabetic subjects, of well-known kinetic analysis software package SAAM II, and by application on different data. Agreement between MATLAB and SAAM II was warranted by intraclass correlation coefficients ≥0.73; no significant differences between corresponding mean parameter estimates and prediction of HID rate; and consistent residual analysis. Moreover, MATLAB optimization procedure resulted in a significant 51% reduction of CV% for the worst-estimated parameter by SAAM II and in maintaining all model-parameter CV% MATLAB-based procedure was suggested as a suitable tool for the individual assessment of HID process. Copyright © 2012 Elsevier Ireland Ltd. All rights reserved.

  13. Hair as an indicator of the body content of polonium in humans: Preliminary results from study of five male volunteers

    DEFF Research Database (Denmark)

    Rääf, C.L.; Holstein, H.; Holm, E.

    2015-01-01

    radioactive polonium (209Po as a bio-tracer for 210Po) in well determined quantities. Four of the volunteers were given 5-10Bq 209Po in a single intake (acute intake) and one volunteer has ingested a daily intake of 58.7mBq 209Po for a period of 180 d. Human hair was found to reflect the daily clearance...

  14. Measurement the concentration of polonium 210Po and find annual dose resulting from eating certain foods by the individual Iraqi

    International Nuclear Information System (INIS)

    Al-Emam, A. M.; Mhemeed, A.K.; Hasan, H.I.

    2012-12-01

    The present study aims to determine the concentration of polonium 2 10P o in some of the food consumed by the Iraqi individual collecting (27) sample produced within the country, including imported and available in local markets to some Iraqi provinces, and these foods included potatoes, wheat and fish. To find concentration of polonium 2 10P o method is used chemical separation and deposition on silver disc, and use surface barrier detector to find alpha particle spectrum for polonium and find concentrations ere at 7.15, 2.58, 6.86 Bq / kg, for each of potatoes, wheat and fish, respectively, Daily intake rate for polotuinm 2 10P o which found in the food under study was measured, and show that the annual dose resulting from eating foods that contain this element was at 4.55, 87,69, 0.298 μSv/ y for food stuff mentioned are compatible with universal values and within the permissible limits worldwide. (Author)

  15. An Empirical Comparison of Discrete Choice Experiment and Best-Worst Scaling to Estimate Stakeholders' Risk Tolerance for Hip Replacement Surgery.

    Science.gov (United States)

    van Dijk, Joris D; Groothuis-Oudshoorn, Catharina G M; Marshall, Deborah A; IJzerman, Maarten J

    2016-06-01

    Previous studies have been inconclusive regarding the validity and reliability of preference elicitation methods. The aim of this study was to compare the metrics obtained from a discrete choice experiment (DCE) and profile-case best-worst scaling (BWS) with respect to hip replacement. We surveyed the general US population of men aged 45 to 65 years, and potentially eligible for hip replacement surgery. The survey included sociodemographic questions, eight DCE questions, and twelve BWS questions. Attributes were the probability of a first and second revision, pain relief, ability to participate in sports and perform daily activities, and length of hospital stay. Conditional logit analysis was used to estimate attribute weights, level preferences, and the maximum acceptable risk (MAR) for undergoing revision surgery in six hypothetical treatment scenarios with different attribute levels. A total of 429 (96%) respondents were included. Comparable attribute weights and level preferences were found for both BWS and DCE. Preferences were greatest for hip replacement surgery with high pain relief and the ability to participate in sports and perform daily activities. Although the estimated MARs for revision surgery followed the same trend, the MARs were systematically higher in five of the six scenarios using DCE. This study confirms previous findings that BWS or DCEs are comparable in estimating attribute weights and level preferences. However, the risk tolerance threshold based on the estimation of MAR differs between these methods, possibly leading to inconsistency in comparing treatment scenarios. Copyright © 2016 International Society for Pharmacoeconomics and Outcomes Research (ISPOR). Published by Elsevier Inc. All rights reserved.

  16. Polonium 2 sup 1 sup 0 and lead 2 sup 1 sup 0 in Syrian sea and river fish and radiation dose due to their consumption

    International Nuclear Information System (INIS)

    Al-Masri, M.S.; Mamish, S.; Budier, Y.; Nashwati, A.

    1999-01-01

    Edible part of 36 types of sea fish collected from local market (Lattakia, Tartus, Banias) and seven types of river fish (Al-Furat river and Mzerib lake) have been analyzed for 210 Po and 210 Pb. Results of analysis have shown that 210 Po and 210 Pb concentrations in sea fish varied between 0.27 and 27.48 Bq/kg and between 0.05 and 0.38 Bq/kg, respectively while for river fish concentrations were relatively low and varied between 0.61 and 3.08 Bq/kg for 210 Po and between 0.04 and 0.10 Bq/kg for 210 Pb. In addition, the Syrian adults daily intakes of 210 Po and 210 Pb have been estimated and found to be 6.0 and 0.24 mBq respectively. These intakes are much less than those reported in other areas in the world. The collective dose was also determined and found to be about 5.09 man.sv for polonium 210 and 2.93 man.sv for lead 210 . (author)

  17. Evaluation of sample pretreatment methods for analysis of Polonium isotopes in herbal medicine

    International Nuclear Information System (INIS)

    Sathyapriya, R.S.; Nair, Madhu G.; Rao, D.D.

    2013-01-01

    Ayurvedic medicines are widely consumed by Indian population both for treatment and good health Ayurvedic medicines are used in various forms like infusions, decoctions, powder, tablets, fermented decoction (Arishta) etc. Arishtas are prepared using plant extracts soaked in sugar or jaggery and are generally consume on regular basis for good health. Hence an effort was made to analyse the natural radioactivity in the Ayurvedic Arishtas. 213 Po is an important naturally occurring radionuclide that volatilizes beyond 150℃. Hence adequate care is needed during sample pretreatment step. Both physical (freeze-drying, open vessel evaporation and microwave digestion) and chemical (digestion using various mineral acids like aqua regia, Con. HNO 3 , H 2 SO 4 and oxidizing agents like H 2 O 2 and HClO 4 ) pretreatment procedures were adopted. After the initial sample treatment polonium radionuclide was pre-concentrated using calcium phosphate co-precipitation. Calcium phosphate precipitate was dissolved in 150 ml of 0.5M HCI solution with approximately 1 g of ascorbic acid for auto deposition of Polonium on silver planchette for 3 hours at 90℃ on a rotary hot plate. The sample sources were counted in calibrated alpha spectrometer with 450 mm 2 low-back-ground PIPS detector interfaced with ECIL MCA. The spectrum analysis was done using PHAST Software. 209 Po tracer, at low levels was added to the samples for assessing the radiochemical recovery. The recovery ranged between 18-83 %. The lowest recovery was obtained for the samples that were processed by open vessel digestion with HNO 3 + HCIO 4 + H 2 O 2 . The highest recover was for those samples that were freeze dried and subjected to HNO 3 + HCIO 4 + H 2 O 2 acid digestion at 90℃ for 8 hours. 210 Po concentration in a few samples varied between 0.3-3.5 mBq/L. The paper presents the results of radiochemical recoveries for different pretreatment methods and also the 210 Po content in the ayurvedic arishtas. (author)

  18. Histologic observations on the pathogenesis of lung cancer in hamsters following administration of polonium-210

    International Nuclear Information System (INIS)

    Lisco, H.; Kennedy, A.R.; Little, J.B.

    1974-01-01

    A serial sacrifice experiment was carried out to study the site of origin and the stages in development of lung cancer in hamsters induced by polonium-210 ( 210 Po). 1 or 2 animals were sacrificed weekly during and after a course of 7 intratracheal instillations of 0.1 μCi of 210 Po in saline. This exposure produced a transient radiation pneumonitis of moderate severity during, and for several weeks after, the instillation period. Subsequent pathological changes included hyperplasia of bronchiolar epithelium, and focal proliferation of epithelial cells in peribronchiolar and more remote alveoli, termed epithelialization of alveoli. Hyperplastic bronchiolar epithelium frequently showed numerous Clara cells which exhibited pleomorphism of cells and nuclei, multinucleated cells, and striking changes in staining characteristics of secretory granules. Epithelialization of alveoli showed steady progression from well-circumscribed small foci to larger confluent lesions which were composed of various cell types and resembled tumors. Malignant tumors occurred in many animals surviving more than 24 weeks after the last instillation of 210 Po

  19. Activity levels of polonium-210 in tobacco and cigarette in Iran

    International Nuclear Information System (INIS)

    Ghanbar Moghaddam, B.; Vahabi Moghaddam, M.; Fathi Vand, A. A.

    2011-01-01

    Polonium-210 ( 210 Po) is a natural contaminant of tobacco and its products. Due to its volatility and inherent adsorption properties, 210 Po is one of the major potential sources of human exposure through smoking. This paper reports measurements on 210 Po and 210 Pb levels in domestic as well as imported tobacco to Iran through α-spectrometry technique. The fate of 210 Po radionuclide has been also followed from tobacco farm through curing procedure in factory. The activity levels of 210 Po in Iranian domestic and imported cigarettes is found to be on the average as 38.4±0.8 mBq/g with a range of 30.3-51.3 mBq/g and 20.0±0.6 mBq/g with a range of 18.6-21.7 mBq/g, respectively. These levels are considerably higher than those reported in many other parts of the world. In the case of tobacco produced in Iranian northern province of Guilan, drying in closed compartments by fossil fuel and elevated inventories of 210 Po in soil due to over application of phosphate-rich fertilizers seems to be the main causes of these elevated activity levels.

  20. Radioactive contamination in human by polonium-210 in food from marine origin

    International Nuclear Information System (INIS)

    Kelecom, Alphonse; Gouvea, Rita de Cassia S.; Kelecom, Philippe Marcel

    2005-01-01

    Food from marine origin is considered as one of the sources that most contributes to internal radioactive contamination in humans by polonium-210 ( 210 Po). This work intended to check whether a single ingestion of the mussel Perna perna should result in a detectable increase of radioactive contamination in the consumer. The mussel was bought at a fish market localized in the city of Niteroi, RJ, Brazil. It was cooked as usually, and its content in 210 Po determined after acid mineralization, spontaneous electrodeposition on stainless steel disks and alpha counting. Non-smoking volunteers maintained for two weeks a normal diet, but completely avoiding fish and seafood. Then, they ate 200 g of cooked mussel, and collected total faeces and urine every day during ten days. 210 Po level in faeces samples showed a 900% increase at the first day after ingestion, and reached normal levels after 3-4 days. In urine samples, the increase of 210 Po was much lower (50%) and reached a maximum at the fifth day. Such data showed a short time permanence of 210 Po in the intestine. Most of ingested 210 Po (∼91%) was eliminated in up to 5 days through faeces. A small amount was absorbed (∼5-10%), part of it being eliminated in urine, and the remaining contaminated the human body. (author)

  1. Transfer of the uranium decay products, polonium-210 and lead-210, through the lichen-caribou-wolf food chain in northern Canada (manuscript report)

    International Nuclear Information System (INIS)

    Thomas, P.A.

    1991-05-01

    The main purpose of this study is to investigate the accumulation and transfer of polonium-210 and lead-210 in the arctic food chain, lichen-caribou-wolf, in the Northwest Territories. Polonium-210 arises from lead-210 decay and is a widespread alpha-emitting radionuclide. It seeks soft tissue and has the potential to accumulate in the food chain. Caribou, wolves and other wildlife may become exposed to enhanced levels of these two uranium-series radionuclides if the proposed uranium mine near Baker Lake, Northwest Territories, proceeds. Baker Lake lies at the crossroads of the ranges of the Beverly, the Kaminuriak and the Wager Bay caribou herds. Therefore, it is important to establish baseline concentrations and natural food chain transfer of uranium series radionuclides, in this study. This information can be used for baseline data before any further mining development takes place. This study will also provide data regarding the statistical uncertainty attached to transfer coefficients. This can help ensure reliable and appropriate future monitoring of environmental change. With the participation of the hunters of Baker Lake, caribou and wolf samples were collected and analyzed for polonium. Results indicate that polonium-210 activity in caribou tissues were somewhat higher than previous data reported from Alaska. Transfer coefficients for polonium-210 from caribou to wolf were near unity for many tissues. However, polonium-210 does not appear to cross the placenta in caribou. Further study includes lichen collections and collection of further caribou samples from the beverly herd in order to determine transfer from lichens to caribou in both the Baker Lake and Snowdrift areas in the Northwest Territories. (author). 26 refs., 3 tabs

  2. Transfer of the uranium decay products, polonium-210 and lead-210, through the lichen-caribou-wolf food chain in northern Canada (manuscript report)

    Energy Technology Data Exchange (ETDEWEB)

    Thomas, P A [Sasatchewan Univ., Saskatoon (Canada). Biology Dept.

    1991-05-01

    The main purpose of this study is to investigate the accumulation and transfer of polonium-210 and lead-210 in the arctic food chain, lichen-caribou-wolf, in the Northwest Territories. Polonium-210 arises from lead-210 decay and is a widespread alpha-emitting radionuclide. It seeks soft tissue and has the potential to accumulate in the food chain. Caribou, wolves and other wildlife may become exposed to enhanced levels of these two uranium-series radionuclides if the proposed uranium mine near Baker Lake, Northwest Territories, proceeds. Baker Lake lies at the crossroads of the ranges of the Beverly, the Kaminuriak and the Wager Bay caribou herds. Therefore, it is important to establish baseline concentrations and natural food chain transfer of uranium series radionuclides, in this study. This information can be used for baseline data before any further mining development takes place. This study will also provide data regarding the statistical uncertainty attached to transfer coefficients. This can help ensure reliable and appropriate future monitoring of environmental change. With the participation of the hunters of Baker Lake, caribou and wolf samples were collected and analyzed for polonium. Results indicate that polonium-210 activity in caribou tissues were somewhat higher than previous data reported from Alaska. Transfer coefficients for polonium-210 from caribou to wolf were near unity for many tissues. However, polonium-210 does not appear to cross the placenta in caribou. Further study includes lichen collections and collection of further caribou samples from the beverly herd in order to determine transfer from lichens to caribou in both the Baker Lake and Snowdrift areas in the Northwest Territories. (author). 26 refs., 3 tabs.

  3. Analysis of prospecting effect of polonium survey and geoelectric survey extracted uranium and molybdenum in the south of Shengyuan volcanic basin

    International Nuclear Information System (INIS)

    Jin Hehai

    2007-01-01

    Polonium survey and geoelectric survey extracted uranium and molybdenum show that compound anomaly with sharp anomaly peak of the curve of polonium-210, uranium, molybdenum appears along many survey lines in Bakou area, Shengyuan volcanic basin, which may reflect the enrichment of uranium and molybdenum in rock formation and soil layer. By contrasting the anomaly curve to that above the buried uranium deposit, it is recognized that compound anomaly is closely related to the uranium mineralization condition in the area and some favourable sites for uranium metallogeny have been predicated. (authors)

  4. A study of chemical forms of polonium-210 and lead-210 in air particulates in phosphate mines and Tartous port

    International Nuclear Information System (INIS)

    Al-Masri, M.S.; Al-Kharfan, K.; Khalili, H.; Hasan, M.

    2003-03-01

    Chemical forms of polonium-210 and lead-210 in air particulates of two areas having different climate conditions (Phosphate mines and Tartous port) have been studied. Air particulates were collected at six periods covering the climate changes from September 2000 until February 2002. Total suspended particulates (TSP) concentration was varied between 1827 and 9722 μg/M 3 and 197 and 1135 μg/m 3 in phosphate mines and Tartous port respectively; all of these values were higher than the maximum permissible concentration according to the Syrian standard (120 μg/m 3 ). Results of 210 po and 210 Pb extraction from the air particulates using selective solutions have shown that inorganic and insoluble 210 Po and 210 Pb (attached to silica and not soluble in mineral acids) ratio was high in phosphate mine air particulates and reached a value of 94% and 77% respectively. While the amount of lead 210 attached to organic compounds has reached a value of 24%. In addition, small variations in total inorganic and insoluble 210 Po and 210 Pb during the year were observed with little differences between polonium 210 ratio in both Tartous port and phosphate mines, which indicated that variations in climate conditions may affect the chemical forms. In both cases, inorganic and insoluble polonium 210 and lead 210 ratio was high; this may lead to their attachment to lung cells and their transfer via body streams. Moreover, the date obtained in this study can be utilized to calculate the radiation dose due to inhalation of radon gas and its decay daughters in the Syrian phosphate sites. (author)

  5. 78 FR 40027 - Novaluron; Pesticide Tolerances

    Science.gov (United States)

    2013-07-03

    ...). This regulation additionally deletes the time- limited tolerance for strawberry, as that tolerance..., pears, potatoes, strawberries, and tomatoes and utilized estimates for PCT for recently registered uses... deletes the time-limited tolerance for strawberry, as that tolerance expired on December 31, 2011. VI...

  6. Individual monitoring conducted by the Health Protection Agency in the London polonium-210 incident

    International Nuclear Information System (INIS)

    Bailey, Michael; Birchall, Alan; Etherington, George; Wilkins, Bernard; Bishop, Louise; Fraser, Graham; Gross, Roger; Maguire, Helen; Evans, Barry; Shaw, Karen

    2008-01-01

    Mr. Alexander Litvinenko died on 23 November 2006, having allegedly been poisoned with polonium- 210 ( 210 Po) a few weeks earlier. The police investigation identified a number of contaminated locations, including parts of several hotels, restaurants, offices and transport. An extensive programme of individual monitoring of potentially exposed persons was rapidly initiated, based on urine sampling. Methods used for low-level measurement of 210 Po in environmental samples were adapted. The Health Protection Agency set a Reporting Level of 30 mBq d -1 , results above which indicated likely intake of 210 Po from the incident. At each location, risk assessments were undertaken to identify persons with significant risk of contamination with 210 Po. These individuals were invited to provide samples, not only to enable a direct assessment to be made of their own exposures, but also to inform decisions on whether others connected with the location should provide samples, or whether they could be reassured. Urine samples from 753 people were processed: about 500 during the first month. Of these, 139 measurements were above the Reporting Level, assessed doses for 36 were in the range ≥ 1 mSv and <6 mSv, and 17 were ≥ 6 mSv, with the highest at about 100 mSv. Many of the hotel guests were overseas visitors. An Overseas Advice Team was set up to encourage authorities abroad to adopt similar strategies. Overall, 664 persons from 52 countries and territories were identified. For 176, results of urine measurements were provided to the Overseas Advice Team, of which 13 were above the Reporting Level. Assessed doses for eight of these were <1 mSv, and the other five were in the range ≥ 1 mSv and <6 mSv. (author)

  7. Polonium-210 in dried fin fishes of Tuticorin, Southeast coast of India

    International Nuclear Information System (INIS)

    Carol, R.; Wesley, S.G.

    2013-01-01

    Tuticorin is one of the major sea-ports and fish-landing centres in the southeastern coast of India. Most of the fishes landed in this coast are consumed fresh and 40% of the fishes are used in the dried form. 210 Po (t 1/2 = 138.4 days) in marine food has received much interest from the scientific community because of its high toxicity and the radioactive dose it delivers to marine organisms and human beings when compared to anthropogenic radionuclides released into coastal waters. Although many studies have been conducted in fresh fishes from various coasts concerning 210 Po, sufficient data are not available for value-added dried marine fish products. In the present study, 210 Po and 210 Pb were quantified in some commercially important dried fishes and their exposure to humans studied. Polonium-210 was determined after wet digestion and counted using an alpha probe. Overall, the concentration of 210 Po in the dried fish muscle tissue ranged from 1.45 ± 0.82 to 559.23 ± 5.45 Bq kg -1 . The highest concentration in the muscle tissue was recorded for the species Stolephorus brevisensis (559.23 ± 8.9 Bq kg -1 ) belonging to the group Clupeidae and the lowest in Harpodon sp. (Bombay duck). The 210 Po dose receive by the public due to consumption of the dried fishes was found to be in the range of 25.2-350.3 μSV yr -1 and the fish samples were found to be radiologically safe. (author)

  8. Polonium-210 accumulates in a lake receiving coal mine discharges-anthropogenic or natural?

    Science.gov (United States)

    Nelson, A W; Eitrheim, E S; Knight, A W; May, D; Wichman, M D; Forbes, T Z; Schultz, M K

    2017-02-01

    Coal is an integral part of global energy production; however, coal mining is associated with numerous environmental health impacts. It is well documented that coal-mine waste can contaminate the environment with naturally-occurring radionuclides from the uranium-238 ( 238 U) decay series. However, the behavior of the final radionuclide in the 238 U-series, i.e., polonium-210 ( 210 Po) arising from coal-mine waste-water discharge is largely unexplored. Here, results of a year-long (2014-2015) field study, in which the concentrations of 210 Po in sediments and surface water of a lake that receives coal-mine waste-water discharge in West Virginia are presented. Initial measurements identified levels of 210 Po in the lake sediments that were in excess of that which could be attributed to ambient U-series parent radionuclides; and were indicative of discharge site contamination of the lake ecosystem. However, control sediment obtained from a similar lake system in Iowa (an area with no coal mining or unconventional drilling) suggests that the levels of 210 Po in the lake are a natural phenomenon; and are likely unrelated to waste-water treatment discharges. Elevated levels of 210 Po have been reported in lake bottom sediments previously, yet very little information is available on the radioecological implications of 210 Po accumulation in lake bottom sediments. The findings of this study suggest that (Monthly Energy Review, 2016) the natural accumulation and retention of 210 Po in lake sediments may be a greater than previously considered (Chadwick et al., 2013) careful selection of control sites is important to prevent the inappropriate attribution of elevated levels of NORM in lake bottom ecosystems to industrial sources; and (Van Hook, 1979) further investigation of the source-terms and potential impacts on elevated 210 Po in lake-sediment ecosystems is warranted. Copyright © 2016 Elsevier Ltd. All rights reserved.

  9. Death by polonium-210: lessons learned from the murder of former Soviet spy Alexander Litvinenko.

    Science.gov (United States)

    McFee, Robin B; Leikin, Jerrold B

    2009-02-01

    The medical response to radiation--whether the result of radiological warfare, terrorist deployment of improvised radiation dispersal weapons, political assassination, occupational or industrial accidents or the medically radiated patient remains one of the least taught among all disciplines within medical education. In the aftermath of 9/11 among medical vulnerabilities to toxicant threats, of all the categories of weapons of mass destruction (WMD)--whether using the CBRNE (chemical, biological, radiological, nuclear, explosive) or NBC (nuclear, biological, chemical) acronym--radiation is the least taught in professional schools, responder cultures or civil preparedness organizations. To date, few health care professionals (HCP) possess the fundamental knowledge or skills to identify and diagnose, let alone treat a radiation victim; this vulnerability made even more obvious in the aftermath of the high profile assassination of former Russian agent Alexander Litvinenko. He was poisoned with Polonium210. Radioactive substances are ubiquitous with radiation sources being in or transported through virtually every region nationwide. It is essential to increase preparedness among community and rural health care facilities as well as urban and university hospitals. Managing radiation injuries effectively requires access to specialized equipment and expertise. Radiation sickness is progressive and may require acute, critical and long-term care throughout the course of illness. Regardless of the source, preparedness rests upon acknowledging a threat exists and dedicating the resources to address the risks including the enhancement of training and equipment. Mass or individual exposures to radiation present unique challenges to the entire response continuum from law enforcement, first responders and emergency medical care. Increased education about and practice in responding to radiological threats is essential to enhance preparedness.

  10. Crafting tolerance

    DEFF Research Database (Denmark)

    Kirchner, Antje; Freitag, Markus; Rapp, Carolin

    2011-01-01

    Ongoing changes in social structures, orientation, and value systems confront us with the growing necessity to address and understand transforming patterns of tolerance as well as specific aspects, such as social tolerance. Based on hierarchical analyses of the latest World Values Survey (2005......–08) and national statistics for 28 countries, we assess both individual and contextual aspects that influence an individual's perception of different social groupings. Using a social tolerance index that captures personal attitudes toward these groupings, we present an institutional theory of social tolerance. Our...

  11. Natural levels of lead-210, polonium-210 and radium-226 in humans and biota of the Arctic

    Energy Technology Data Exchange (ETDEWEB)

    Holtzman, R B

    1966-06-11

    Relatively high concentrations of some fission products in humans and biota from Lapland and Alaska have been reported. These have been attributed to the continual accumulation of those products on the long-lived, slow-growing Arctic lichens and sedges. Such plants are an important source of forage for reindeer and caribou, the meat of which, in turn, constitutes a substantial portion of the diets of Laplanders and Eskimos. These high levels of fall-out suggest, together with the proposed mechanism of uptake and the similarities to strontium-90 in atmospheric distribution and biochemistry, that in Arctic biota, the naturally occurring airborne nuclides lead-210 and its decay product, polonium-210, may also be present in high concentration. These naturally occurring fall-out activities are of special interest in studies of aerosol precipitation mechanisms because their levels are independent of bomb tests and consequently they have been constant over the years. Because of this constancy and the high energy of the particles emitted by the lead-210 series (a 5.3-MeV ..cap alpha..-particle from polonium-210 and a 0.4-MeV (average energy) ..beta..-particle from bismuth-210 compared with ..beta..-rays with average energies of 0.4 MeV from cesium-137 and 1.1 MeV from strontium-90 (yttrium-90)), the radiation dose to Arctic biota from this source may be quite significant relative to that from artificial ones. 24 references.

  12. Transfer factor of Radium -226, lead-210 and Polonium-210 from Norm contaminated soil to Atriplex, Afelfa and Bermuda grasses

    International Nuclear Information System (INIS)

    Al-Masri, M.S.; Mukhallati, H.; Al-Hamwi, A.

    2011-10-01

    transfer factors of Radium -226, lead-210 and Polonium-210 from contaminated soil with oil coproduced water to grazing plants in the north eastern region of Syria have been determined. contaminated soil was collected from one of the AL-Furat Petroleum Oil company oil fields;soil was distributed into several pots where the studied plants were planted in order to study the transfer factors of radioisotopes to them. Results have shown that the mean transfer factors of radium to green parts have reached has reached 0.0016 in Atriplex halimus L.,0.0021 in Atriplex canescens Nutt, 0.0025 in Atriplex Leucoclada Bioss,0.0082 in Bermuda grass and 0.0167 in Medicago Sativ L,which was the highest,while the transfer factors of polonium and lead were ten times higher than those for radium and reacted 0.012 in Atriplex Leucoclada Bioss, 0.011 in Atriplex canescens Nutt, 0.007 in Atriplex halimus L.0.32 in bermuda grass and 0.025 in Afelfa.(author)

  13. Transfer of the uranium decay products, polonium-210 and lead-210, through the lichen-cariboo-wolf food chain in northern Canada. Manuscript report No. MR18-91

    Energy Technology Data Exchange (ETDEWEB)

    Thomas, P A

    1991-01-01

    Study to investigate the accumulation and transfer of polonium-210 and lead-210 in the Arctic food chain lichen-caribou-wolf in the Northwest Territories. With the participation of the hunters of Baker Lake, caribou and wolf samples were collected and analyzed for polonium. The level of polonium-210 was determined in lichen, several caribou tissues, and several wolf tissues. Transfer coefficients were derived between trophic levels in the food chain and the Po-210:PB-210 ratios for lichens and selected tissues in caribou and wolf were determined.

  14. The laboratory books of Pierre and Marie Curie. Note proposed to the Sciences Academy on july the 18. of the year 1898 and the polonium discovery

    International Nuclear Information System (INIS)

    Adloff, J.P.

    1998-01-01

    Chemical research on radioactivity started in 1898. That year, a note was presented by the Curies on the discovery of a new radioactive material contained in pechblende and called ''polonium''. The different steps of the discovery and the experiments carried out are related as well as the surprises, the questioning and the doubts of the Curies in the years immediately following. (O.M.)

  15. Uranium, radon-222 and polonium-210 in drinking waters from metropolitan area of Recife, PE, Brazil

    International Nuclear Information System (INIS)

    Silva, Cleomacio Miguel da

    2000-04-01

    There is only scarce information on the presence of radionuclides in water for public consumption in Brazil. A recently issued federal regulation requires that waters from public supplies be screened to determine their content of alpha and beta emitters. In order to comply with this requirement the present work was carried out with the purpose of determining the concentration of natural uranium, 222 Rn and 210 Po in water supplies in the metropolitan region of Recife, Brazil. The analyses were performed in 17 points of supply of superficial water and 94 points of groundwater supply. The concentrations of uranium were determined by the fluorimetric method, whereas the liquid scintillation method was used to determine the concentration of 222 Rn. Polonium-210, on the other hand, was determined by alpha spectrometry, following its spontaneous deposition on copper disks. The water analyzer presented uranium concentrations varying from 35.3 to 1146.5 mBq/L for superficial resources and from 20.2 to 919.15 mBq/L for underground sources. The concentration of uranium in superficial water showed significant correlation with some parameters such as conductivity, alkalinity and total hardness, as well as, with the concentrations of Ca, Mg, Cl, K, SO 4 and Mn. No correlation, however, was shown with the concentrations of Fe, NO 2 and NO 3 . The concentrations of 222 Rn varied from 5.3 to 83.7 Bq/L in the groundwater analyzer. Radon concentration was not measured in superficial water due to the high emanation rate of radon in open air conditions. As far as 210 Po is concerned, the analyses showed concentrations ranging from 210 Po did not show and correlation with physico-chemical parameters. The average concentrations of uranium and 210 Po in superficial water were of 44.7 mBq/L, respectively. These values correspond to effective doses of 5.8 x 10 -4 mSv/yr and 4.5 x 10 -2 mSv/yr, for uranium and 210 Po, respectively. The average values for the concentrations of uranium, 222

  16. Normal Tissue Complication Probability Estimation by the Lyman-Kutcher-Burman Method Does Not Accurately Predict Spinal Cord Tolerance to Stereotactic Radiosurgery

    International Nuclear Information System (INIS)

    Daly, Megan E.; Luxton, Gary; Choi, Clara Y.H.; Gibbs, Iris C.; Chang, Steven D.; Adler, John R.; Soltys, Scott G.

    2012-01-01

    Purpose: To determine whether normal tissue complication probability (NTCP) analyses of the human spinal cord by use of the Lyman-Kutcher-Burman (LKB) model, supplemented by linear–quadratic modeling to account for the effect of fractionation, predict the risk of myelopathy from stereotactic radiosurgery (SRS). Methods and Materials: From November 2001 to July 2008, 24 spinal hemangioblastomas in 17 patients were treated with SRS. Of the tumors, 17 received 1 fraction with a median dose of 20 Gy (range, 18–30 Gy) and 7 received 20 to 25 Gy in 2 or 3 sessions, with cord maximum doses of 22.7 Gy (range, 17.8–30.9 Gy) and 22.0 Gy (range, 20.2–26.6 Gy), respectively. By use of conventional values for α/β, volume parameter n, 50% complication probability dose TD 50 , and inverse slope parameter m, a computationally simplified implementation of the LKB model was used to calculate the biologically equivalent uniform dose and NTCP for each treatment. Exploratory calculations were performed with alternate values of α/β and n. Results: In this study 1 case (4%) of myelopathy occurred. The LKB model using radiobiological parameters from Emami and the logistic model with parameters from Schultheiss overestimated complication rates, predicting 13 complications (54%) and 18 complications (75%), respectively. An increase in the volume parameter (n), to assume greater parallel organization, improved the predictive value of the models. Maximum-likelihood LKB fitting of α/β and n yielded better predictions (0.7 complications), with n = 0.023 and α/β = 17.8 Gy. Conclusions: The spinal cord tolerance to the dosimetry of SRS is higher than predicted by the LKB model using any set of accepted parameters. Only a high α/β value in the LKB model and only a large volume effect in the logistic model with Schultheiss data could explain the low number of complications observed. This finding emphasizes that radiobiological models traditionally used to estimate spinal cord NTCP

  17. Induction of the lambda bacteriophage synthesis in Escherichia coli K 12 by polonium alpha rays; Induction de la synthese du bacteriophage lambda chez Escherichia coli K 12 par les rayons alpha du polonium

    Energy Technology Data Exchange (ETDEWEB)

    Devoret, Raymond

    1958-06-15

    This research thesis reports the study of the inducing action of polonium alpha radiations in Escherichia Coli K 12 by using an external irradiation device. This work comprised the development of a method to spread bacteria in layer with a thickness less than 20 microns, and the measurement of the number of α particles falling on the irradiated surface. This measurement has been performed by using a nuclear emulsion and a simple photographic film. It appears that alpha radiations have an inducing action, and that at most 15 per cent of bacteria can be induced. The comparison of the induction curve with the survival curves of lysogen and sensitive stains shows that there is no abortive induction. Thus, it appears that this inducing action is not due to an indirect effect of the irradiated medium [French] Dans ce travail on a etudie l'action inductrice des rayons alphas du polonium chez Escherichia Coli K 12 par un diapoaitif d'irradiation externe. Son utilisation necessitait: - une methode d'etalement des bacteries en couche de moins de 20 microns d'epaisseur; - une mesure du nombre des particules alpha tombant sur la surface etendue irradiee. Les mesures ont ete faites a l'aide d'une emulsion nucleaire et d'un film photographique ordinaire. 1) Les rayons alphas ont une action inductrice. Au plus 15 pc des bacteries peuvent etre induites. 2) La oomparaison de la courbe d'induction et des courbes de survie des souches lysogene et sensible montre qu'il n'y a pas d'inductions abortives. 3) Cette action inductrice n'est pas due a un effet indirect du milieu irradie. (auteur)

  18. Om tolerance

    DEFF Research Database (Denmark)

    Huggler, Jørgen

    2007-01-01

    Begrebet tolerance og dets betydninger diskuteres med henblik på en tydeliggørelse af begrebets forbindelse med stat, religion, ytringsfrihed, skeptisk erkendelsesteori, antropologi og pædagogik.......Begrebet tolerance og dets betydninger diskuteres med henblik på en tydeliggørelse af begrebets forbindelse med stat, religion, ytringsfrihed, skeptisk erkendelsesteori, antropologi og pædagogik....

  19. Elementary analyses in behalf of the project: Orientating investigation to Polonium-210 and other radionuclides in Dutch aquatic ecosystems

    International Nuclear Information System (INIS)

    Hart, M.J. 't; Breugem, P.M.; Koester, H.W.

    1989-11-01

    In this report, results of the determinations of total, organic and inorganic carbon analysis are reported for the project 'Orientating investigations of Polonium-210 and other natural radionuclides in Dutch aquatic ecosystems', projectnumber 248476. The method used is a modification of the method described by Froelich and is based on elemental analysis. Sediment samples from several locations of sea and river water show a large variation of the carbon content. The organic carbon concentration varies from 2.78 to 22.42 percent; the inorganic carbon varies from 1.25 to 5.66 percent. The analyses were run in duplicate with a mean standard deviation of 0.1 percent. (author). 4 refs.; 5 figs.; 7 tabs

  20. Studies on Polonium-210 and Lead-210 aspects in a near shore coastal environment at Kalpakkam, Tamilnadu, India

    International Nuclear Information System (INIS)

    Iyengar, M.A.R.

    2013-01-01

    In the present study, an attempt has been made to summarize the findings from a comprehensive research investigation, related to polonium-210 and lead-210 aspects in a confined near shore coastal marine environment at the site of Kalpakkam nuclear complex. The site hosts some major nuclear installations, the main units being a nuclear power station, fast breeder reactor units, reprocessing facilities and supporting facilities. These investigation have been carried out to evaluate the natural radiation exposures of the resident human population in the neighbourhood of the site complex, and compute the additional potential doses to the community, arising from operation of nuclear facilities. An added significance, surfaced during the study, was the presence of a higher natural radiation background in the study area, due to the occurrence of monazite - a thorium mineral - bearing beach sands in vast stretches of the coastal areas

  1. Polonium (210Po) and uranium (234U, 238U) in water, phosphogypsum and their bioaccumulation in plants around phosphogypsum waste heap at Wislinka (nothern Poland)

    International Nuclear Information System (INIS)

    Skwarzec, B.; Borylo, A.; Kosinska, A.; Radzajewska, S.

    2010-01-01

    The principal sources of polonium and uranium radionuclides the Wislinka area waste dump are phosphorites and phosphogypsum produced by the Phosphoric Fertilizers Industry of Gdansk. The values of uranium and polonium concentration in water with immediate surroundings of waste heap are considerably higher than in the waters of the Martwa Wisla river. The activity ratio 234 U/ 238 U is approximately about one in the phosphogypsum (0.97±0.06 and 0.99±0.04) and in the water of a retention reservoir and a pumping station (0.92±0.01 and 0.99±0.04), while in the water from the Martwa Wisla river is slightly higher than one (1.00±0.07 and 1.06±0.02). The leaching process of uranium and polonium from the phosphogypsum waste heap is responsible for the maximum uranium concentration (1097±6 μg·dm -3 and 1177±6 μg·dm -3 ) and the high 210 Po concentration (131.4±0.9 mBq·dm -3 and 165.7±1.4 mBq·dm -3 ) in the retention reservoir. The major source of polonium and uranium in plants are wet and dry atmospheric falls gathering soil and air dust from the phosphogypsum waste dump and root system. The highest uranium and polonium concentrations were found in older part of grasses (yellow oatgrass, meadow foxtail, moneywort), exposed to atmospheric falls for a long time. The maximum concentrations of 210 Po were characterized for samples of plant root collected at the retention reservoir (150.50±4.97 and 108.55±3.95 Bq·kg -1 dry mass). Polonium and uranium concentrations in water samples of the Martwa Wisla river are relatively low in comparison with the value in the retention reservoir and pumping station near the phosphogypsum waste heap. This suggests that the radionuclides could be leached from the dumping site to the surrounding environment. (authors)

  2. Sequential extraction procedure for determination of uranium, thorium, radium, lead and polonium radionuclides by alpha spectrometry in environmental samples

    Science.gov (United States)

    Oliveira, J. M.; Carvalho, F. P.

    2006-01-01

    A sequential extraction technique was developed and tested for common naturally-occurring radionuclides. This technique allows the extraction and purification of uranium, thorium, radium, lead, and polonium radionuclides from the same sample. Environmental materials such as water, soil, and biological samples can be analyzed for those radionuclides without matrix interferences in the quality of radioelement purification and in the radiochemical yield. The use of isotopic tracers (232U, 229Th, 224Ra, 209Po, and stable lead carrier) added to the sample in the beginning of the chemical procedure, enables an accurate control of the radiochemical yield for each radioelement. The ion extraction procedure, applied after either complete dissolution of the solid sample with mineral acids or co-precipitation of dissolved radionuclide with MnO2 for aqueous samples, includes the use of commercially available pre-packed columns from Eichrom® and ion exchange columns packed with Bio-Rad resins, in altogether three chromatography columns. All radioactive elements but one are purified and electroplated on stainless steel discs. Polonium is spontaneously plated on a silver disc. The discs are measured using high resolution silicon surface barrier detectors. 210Pb, a beta emitter, can be measured either through the beta emission of 210Bi, or stored for a few months and determined by alpha spectrometry through the in-growth of 210Po. This sequential extraction chromatography technique was tested and validated with the analysis of certified reference materials from the IAEA. Reproducibility was tested through repeated analysis of the same homogeneous material (water sample).

  3. Study of polonium and lead in shellfish (Mytilus Edulis) from NORM discharge area of Aberdeen Bay and Ythan Estuary of Scotland and radiological impact to the local people and environment

    International Nuclear Information System (INIS)

    Satyajit Ghose; Brian Heaton

    2005-01-01

    Introduction The problem of NORM in the oil and gas industry is a result of deposits of radioactive (Ra,BaSO 4 ) scale within pipelines and processing equipment. The build-up of the scale has a significant impact on the activities of the operating company involved and is therefore a costly problem. The pipes and other equipment must therefore be cleaned on a regular basis or disposed of and replaced. Once the LSA scale has been removed from oil processing equipment the main route of disposal is into the sea. This scale contains mainly radium, lead and its daughter products, which have a long half-lives and high radiotoxicity. The volume of NORM waste produced by the petroleum industry is quite impressive. There are 230 oil and gas producing platforms in UK waters together with around 40 onshore oil and gas producing wells. All are involved in NORM production and discharging the NORM contaminated waste to the North Sea. Discharge of radioactive scale waste from offshore platforms into the surface waters of sea has been a matter of concern due to possible environmental effects of radioelements contained in such waters. Subject to certain conditions this is allowed under the UK Radioactive Substances Act 1993 which controls the release of radioactive materials into the environment. In the case for North sea oil and gas field waste, waste from the cleaning of contaminated plant and equipment is either discharged to sea off shore, discharged to sea from a pipeline in Aberdeen or stored at the Dounraey nuclear facility. Although allowed since 1981 no one has ascertained if these conditions are ensuring full protection of fish consumers. Furthermore, the disposal of large amounts of contaminated wastes resulting from the various stages of oil processing can pose an environmental problem due to its content of long lived radionuclides ( 226 Ra t 1/2 = 1600 y and 210 Pb t 1/2 = 22 years). In order that an accurate estimate of the contribution of polonium from NORM discharges

  4. Towards Tolerance

    NARCIS (Netherlands)

    Lisette Kuyper; Jurjen Iedema; Saskia Keuzenkamp

    2013-01-01

    Across Europe, public attitudes towards lesbian, gay and bisexual (LGB) individuals range from broad tolerance to widespread rejection. Attitudes towards homosexuality are more than mere individual opinions, but form part of the social and political structures which foster or hinder the equality

  5. Intolerant tolerance.

    Science.gov (United States)

    Khushf, G

    1994-04-01

    The Hyde Amendment and Roman Catholic attempts to put restrictions on Title X funding have been criticized for being intolerant. However, such criticism fails to appreciate that there are two competing notions of tolerance, one focusing on the limits of state force and accepting pluralism as unavoidable, and the other focusing on the limits of knowledge and advancing pluralism as a good. These two types of tolerance, illustrated in the writings of John Locke and J.S. Mill, each involve an intolerance. In a pluralistic context where the free exercise of religion is respected, John Locke's account of tolerance is preferable. However, it (in a reconstructed form) leads to a minimal state. Positive entitlements to benefits like artificial contraception or nontherapeutic abortions can legitimately be resisted, because an intolerance has already been shown with respect to those that consider the benefit immoral, since their resources have been coopted by taxation to advance an end that is contrary to their own. There is a sliding scale from tolerance (viewed as forbearance) to the affirmation of communal integrity, and this scale maps on to the continuum from negative to positive rights.

  6. Polonium (²¹⁰Po), uranium (²³⁴U, ²³⁸U) isotopes and trace metals in mosses from Sobieszewo Island, northern Poland.

    Science.gov (United States)

    Boryło, Alicja; Nowicki, Waldemar; Olszewski, Grzegorz; Skwarzec, Bogdan

    2012-01-01

    The activity of polonium (210)Po and uranium (234)U, (238)U radionuclides, as well as trace metals in mosses, collected from Sobieszewo Island area (northern Poland), were determined using the alpha spectrometry, AAS (atomic absorption spectrometry) and OES-ICP (atomic emission spectrometry with inductively coupled plasma). The concentrations of mercury (directly from the solid sample) were determined by the cold vapor technique of CV AAS. The obtained results revealed that the concentrations of (210)Po, (234)U, and (238)U in the two analyzed kinds of mosses: schrebers big red stem moss (Pleurozium schreberi) and broom moss (Dicranum scoparium) were similar. The higher polonium concentrations were found in broom moss (Dicranum scoparium), but uranium concentrations were relatively low for both species of analyzed mosses. Among the analyzed trace metals the highest concentration in mosses was recorded for iron, while the lowest for nickel, cadmium and mercury. The obtained studies showed that the sources of polonium and uranium isotopes, as well as trace metals in analyzed mosses are air city contaminations transported from Gdańsk and from existing in the vicinity the phosphogypsum waste heap in Wiślinka (near Gdańsk).

  7. Salt Tolerance

    OpenAIRE

    Xiong, Liming; Zhu, Jian-Kang

    2002-01-01

    Studying salt stress is an important means to the understanding of plant ion homeostasis and osmo-balance. Salt stress research also benefits agriculture because soil salinity significantly limits plant productivity on agricultural lands. Decades of physiological and molecular studies have generated a large body of literature regarding potential salt tolerance determinants. Recent advances in applying molecular genetic analysis and genomics tools in the model plant Arabidopsis thaliana are sh...

  8. Infectious Tolerance

    OpenAIRE

    Jonuleit, Helmut; Schmitt, Edgar; Kakirman, Hacer; Stassen, Michael; Knop, Jürgen; Enk, Alexander H.

    2002-01-01

    Regulatory CD4+CD25+ T cells (Treg) are mandatory for maintaining immunologic self-tolerance. We demonstrate that the cell-cell contact–mediated suppression of conventional CD4+ T cells by human CD25+ Treg cells is fixation resistant, independent from membrane-bound TGF-β but requires activation and protein synthesis of CD25+ Treg cells. Coactivation of CD25+ Treg cells with Treg cell–depleted CD4+ T cells results in anergized CD4+ T cells that in turn inhibit the activation of conventional, ...

  9. Polonium-210 and selenium in tissues and tissue extracts of the mussel Mytilus galloprovincialis (Gulf of Trieste).

    Science.gov (United States)

    Kristan, Urška; Planinšek, Petra; Benedik, Ljudmila; Falnoga, Ingrid; Stibilj, Vekoslava

    2015-01-01

    Marine organisms such as mussels and fish take up polonium (Po) and selenium (Se), and distribute them into different cellular components and compartments. Due to its high radiotoxicity and possible biomagnification across the marine food chain Po-210 is potentially hazardous, while selenium is an essential trace element for humans and animals. The aim of this study was to investigate and compare the presence and extractability of the elements in the mussels Mytilus galloprovincialis collected in the Gulf of Trieste. The levels of Po-210 in the samples ranged from 220 to 400 Bq kg(-1) and of Se from 2.6 to 8.2 mg kg(-1), both on a dry matter basis. Using various extraction types and conditions in water, buffer or enzymatic media, the best extractability was obtained with enzymatic extraction (Protease XIV, 1h shaking at 40 °C) and the worst by water extraction (24 h shaking at 37 °C). 90% of Po-210 and 70% of Se was extractable in the first case versus less than 10% of Po-210 and less than 40% of Se in the second. Such evident differences in extractability between the investigated elements point to different metabolic pathways of the two elements. In enzymatic extracts Se speciation revealed three Se compounds (SeCys2, SeMet, one undefined), while Po-210 levels were too low to allow any conclusions about speciation. Copyright © 2014 Elsevier Ltd. All rights reserved.

  10. Infectious Tolerance

    Science.gov (United States)

    Jonuleit, Helmut; Schmitt, Edgar; Kakirman, Hacer; Stassen, Michael; Knop, Jürgen; Enk, Alexander H.

    2002-01-01

    Regulatory CD4+CD25+ T cells (Treg) are mandatory for maintaining immunologic self-tolerance. We demonstrate that the cell-cell contact–mediated suppression of conventional CD4+ T cells by human CD25+ Treg cells is fixation resistant, independent from membrane-bound TGF-β but requires activation and protein synthesis of CD25+ Treg cells. Coactivation of CD25+ Treg cells with Treg cell–depleted CD4+ T cells results in anergized CD4+ T cells that in turn inhibit the activation of conventional, freshly isolated CD4+ T helper (Th) cells. This infectious suppressive activity, transferred from CD25+ Treg cells via cell contact, is cell contact–independent and partially mediated by soluble transforming growth factor (TGF)-β. The induction of suppressive properties in conventional CD4+ Th cells represents a mechanism underlying the phenomenon of infectious tolerance. This explains previously published conflicting data on the role of TGF-β in CD25+ Treg cell–induced immunosuppression. PMID:12119350

  11. Repressive Tolerance

    DEFF Research Database (Denmark)

    Pedersen, Morten Jarlbæk

    2017-01-01

    Consultation of organised interests and others when drafting laws is often seen as an important source of both input and output legitimacy. But whereas the input side of the equation stems from the very process of listening to societal actors, output legitimacy can only be strengthened if consult......Consultation of organised interests and others when drafting laws is often seen as an important source of both input and output legitimacy. But whereas the input side of the equation stems from the very process of listening to societal actors, output legitimacy can only be strengthened...... a substantial effect on the substance of laws – shows that there is a great difference in the amenability of different branches of government but that, in general, authorities do not listen much despite a very strong consultation institution and tradition. A suggestion for an explanation could be pointing...... to an administrative culture of repressive tolerance of organised interests: authorities listen but only reacts in a very limited sense. This bears in it the risk of jeopardising the knowledge transfer from societal actors to administrative ditto thus harming the consultation institutions’ potential for strengthening...

  12. Gastrointestinal absorption and retention of polonium in adult and newborn rats and guinea pigs

    International Nuclear Information System (INIS)

    Haines, J.W.; Naylor, G.P.L.; Pottinger, H.; Harrison, J.D.

    1993-01-01

    The gastrointestinal absorption of 210 Po was determined by comparing tissue retention after oral and systemic administration. The results indicate an increase in absorption in adult rats for 210 Po administered in liver compared with 210 Po nitrate with estimated absorption of 5 and 13%, respectively. For 210 Po citrate, values of about 7% were obtained in 1-day-old neonate and adult rats while absorption in guinea pigs was estimated to be about 23% in 1-day-old neonates, 17% in 5-day-old neonates, and 9% in adults. Gut retention of ingested 210 Po in neonates was high in rats but not guinea pigs. In adult animals, but not neonates, the liver accounted for a greater proportion of 210 Po reaching the bloodstream after ingestion than after systemic injection. The significance of these results is discussed in relation to current assumptions made in the calculation of doses from 210 Po. (author)

  13. Clinical usefulness of the thickness of preperitoneal and subcutaneous fat layer in the abdomen estimated by ultrasonography for diagnosing abdominal obesity in each type of impaired glucose tolerance in man.

    Science.gov (United States)

    Soyama, Akiko; Nishikawa, Tetsuo; Ishizuka, Toshiharu; Ito, Hiroko; Saito, Jun; Yagi, Kazuo; Saito, Yasushi

    2005-04-01

    For this study we enrolled 1,615 males who were admitted to our hospital for a general health check-up. Plasma glucose (PG) and insulin were measured during 75 g OGTT, and abdominal obesity was assessed by ultrasonography in all subjects. We divided them into several groups: normal glucose tolerance (NGT), high-normal glucose tolerance (h-NGT) who showed >10.0 nmol/l at 1 hr PG among those with NGT, impaired fasting glucose (IFG), impaired glucose tolerance (IGT), IFG + IGT, and DM, according to the results of 75 g OGTT. The aim of the present study was to clarify the clinical characteristics of pre-diabetic disorders relating to metabolic syndrome by comparing various parameters including body mass index (BMI), blood levels of various lipids and abdominal wall fat index (AFI) calculated from the thickness of preperitoneal (Pmax) and subcutaneous (Smin) fat layer in the abdomen estimated by ultrasonography with insulin sensitivity determined by homeostatic model assessment (HOMA-IR) in each type of abnormal glucose regulation as classified by PG changes in 75 g OGTT. We also investigated the relationship between insulin secretion capability and insulin sensitivity to delineate the characteristics of each type of abnormal glucose regulation, and compared the area under the insulin curve (AUCins) and the time axis, and the ability of early insulin secretion by glucose loading (insulinogenic index: I.I.) in each type of abnormal glucose regulation. There was a significant positive correlation between HOMA-IR and Smin or Pmax, suggesting that Smin and Pmax may reflect insulin sensitivity. Abdominal obesity, which was diagnosed from the data of AFI, was present in the h-NGT and IFG + IGT groups, suggesting that those groups belong to the clinical entity of metabolic syndrome. HOMA-IR was higher in IFG than in IGT, although I.I. was reduced and AUCins was increased in IFG as well as in IGT. h-NGT demonstrated a slightly lower I.I. and higher AUCins, compared with IGT

  14. A study on possible use of Urtica dioica (common nettle) plant as polonium (210)Po and lead (210)Pb contamination biomonitor in the area of phosphogypsum stockpile.

    Science.gov (United States)

    Olszewski, Grzegorz; Boryło, Alicja; Skwarzec, Bogdan

    2016-04-01

    The aim of this study was to test a possible use of Urtica dioica (common nettle) plant as a biomonitor of polonium (210)Po and lead (210)Pb contamination near phosphogypsum stacks by determining concentrations of these radionuclides in samples collected from the area of phosphogypsum stockpile in Wiślinka (northern Poland). The (210)Po and (210)Pb contents in roots depended on their concentrations in soils. Bioconcentration factor values from soil to root of the plant did not depend on (210)Po and (210)Pb contents in soils that leads to the conclusion that different polonium and lead species have different affinities to U. dioica plants. The main sources of both analyzed radionuclides in green parts of plants are wet and dry air deposition and transportation from soil. The values of (210)Po/(210)Pb activity ratio indicate natural origin of these radioisotopes in analyzed plants. (210)Po and (210)Pb concentration in U. dioica roots is negatively weakly correlated with distance from phosphogypsum stockpile.

  15. The research for a method for controlling atmospheric pollution in a plutonium treatment cell; Recherche d'une methode de controle de la pollution atmospherique dans une cellule traitant le polonium

    Energy Technology Data Exchange (ETDEWEB)

    Bouteiller, E [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

    1960-07-01

    The aerosols likely to contain {sup 210}Po are trapped by bubbling through an acid solution. The problem of determining the polonium concentration of the solution has been solved by combining it with telluric acid. The reduction is carried out at pH = 0 using a solution of stannous chloride. We have studied the factors influencing coprecipitation; nature of the medium, pH, amounts of telluric acid and of stannous chloride. The average yield for the precipitation is 93 per cent. After precipitation, the polonium is filtered on paper and its activity is measured by means of a scintillation counter. The method makes it possible to measure 1/20 of the maximum permissible dose with an accuracy of 20 per cent. (author) [French] Les aerosols susceptibles de contenir du {sup 210}Po sont captes par barbotage dans une solution acide. Le probleme de la concentration de la solution en polonium a ete resolu en entrainant celui-ci avec de l'acide tellurique. La reduction est effectuee a pH = 0 par une solution de chlorure stanneux. Nous avons etudie les facteurs influencant la coprecipitation: nature du milieu, pH, quantite d'entraineur, quantite de chlorure stanneux. Le rendement moyen de la precipitation est de 93 pour cent. Apres precipitation, le polonium est filtre sur papier et son activite mesuree au compteur a scintillations. La methode permet de mesurer le 1/20 de la dose maximum permise avec une precision de 20 pour cent. (auteur)

  16. The ratio of lead-210 to polonium-210 in U.K. diet.

    Science.gov (United States)

    Smith-Briggs, J L; Bradley, E J; Potter, M D

    1986-10-01

    The levels of the natural radionuclides, 210Pb and 210Po, in U.K. diet have been measured previously. However, in the earlier measurements, the samples were sufficiently aged for 210Pb and 210Po to have attained secular equilibrium. In order to determine the extent of disequilibrium between these radionuclides in fresh food, measurements have been made on recently collected dietary samples. Disequilibrium has been observed in five food groups. The activity per unit mass of 210Pb was found to be greater than that of 210Po in bread, cereals, sugar and preserves, whereas the opposite was found to be true for eggs and beverages. When account is taken of consumption rates, however, the total intakes of 210Pb and 210Po from these food groups are approximately the same. The annual effective dose equivalents from the ingestion of 210Pb and 210Po have been re-estimated at 41 and 12 mu Sv, respectively.

  17. The polonium 210 in aerosols: contribution to the study of savannah fires and volcano emissions

    International Nuclear Information System (INIS)

    Nho-Kim, E.Y.

    1996-01-01

    Natural sources plan a fundamental role on the emission of the species causing climatic variations. The aim of this study is, on the one hand, to estimate fluxes of different components emitted by biomass burning and volcanoes, and on the other hand, to trace these components in time and space. We used 210 Po, last decay product in the 238 U series, as a tracer, as it is one of the characteristic species emitted by these sources: it is highly enriched in these plumes compared to the usual atmosphere and the 210 Po radioactivity is not affected by chemical transformation. We have shown that the contribution of biomass burning on the 210 Po concentration in local background atmosphere is minor during the dry season, compared to that of Saharan soil dusts despite of the importance of this source in the global budget of 210 Po (10%). However, the good correlation observed between the 210 Po concentration and that of carbonaceous aerosols and of CO 2 in biomass burning plumes reveals that 210 Po can be used as a reference of the components emitted by biomass burning. We have estimated the contribution of the Indonesian volcanoes which represent about 5 to 30 % of the global volcanic budget of trace metals. Atmospheric transport of these volcanic plumes was simulated using the 210 Po as a tracer. Due to the characteristic atmospheric circulation in this region, vertical transport is predominant over meridian dispersion, which is moderated by the convergence of the trade winds. The impact of these volcanic emissions on the atmospheric concentration of the trace metals remains a local effect when the volcanic activity is out of cataclysmal eruptions. (author)

  18. Normal dietary levels of radium-226, radium-228, lead-210, and polonium-210 for man

    International Nuclear Information System (INIS)

    Holtzman, R.B.

    1980-01-01

    A review of the literature and the results of some recent measurements on the levels in man's diet of the naturally occurring radionuclides 226 Ra, 228 Ra, 210 Pb, and 210 Po are presented. Intakes in other countries are similar to those in the United States, but in localized populations the 226 Ra intake can be 8 or more pCi/day. The few data on 228 Ra show that intake of this nuclide is about 80% that of 226 Ra except in monazite areas where intakes of up to 160 pCi 228 Ra/day are reported. Drinking water contributes less than 5% to daily intake except in special areas. For 210 Pb, higher levels have been noted for Germany and the Union of Soviet Socialist Republics than for the United States. Persons in the Arctic who consume reindeer or caribou meat may ingest 210 Pb at the rate of 10 to 40 pCi/day. Normal dietary levels of 210 Po are about 20 to 30% higher than those of 210 Pb, except in the Arctic. The levels of these nuclides in classes of foods are compared to show that the higher levels observed in certain diets are due to the levels in particular foods. Because of the high levels of 210 Pb intake in Japan, total skeletal dose rates in that country are estimated to be more than twice those in the United States. The use of dietary intake for estimating metabolic parameters, such as intestinal absorption of 226 Ra and 210 Pb, is discussed

  19. Study on the bioaccumulation of Polonium-210 on bivalve indicator organisms of Tamilnadu and Pondicherry coast (East Coast of India)

    International Nuclear Information System (INIS)

    Syed Mohamed, H.E.; Sadiq Bukhari, A.; Meeramaideen, M.; Masilamani, V.; Shamsudin, Mohamed; Shahul Hameed, P.

    2012-01-01

    210 Po is a major contributor (90%) of the natural radiation dose from alpha-emitting radionuclides, received by most marine organisms. Among marine organisms, benthic fauna are superior to many other biological groups, since they could be monitored due to their sedentary habits and then must either adapt to environmental stress or perish. They also reflect the water conditions not only at the time of sampling but also for some past time as well. The affinity of 210 Po for protein enables it to pass through the food chain, and increased body burdens of 210 Po have been found where diets include protein-rich meat and seafood. The present study was launched to evaluate the rate of accumulation of 210 Po in the benthic bivalve molluscs such as Perna indica, P.viridis, Meretrix casta, Cardium coronatum, Gafrarium tumidum, Paphia textrix, Vellorita cyprinodea and Pinctada sp., of Tamilnadu and Pondicherry coast. Water samples, sediments and bivalves were collected from Gulf of Mannar (6 sampling stations), Palk Strait (8 sampling stations) of Tamilnadu and Pondicherry (6 sampling stations). 210 Po determination as made was as per standard protocols. The results showed that 210 Po concentration in coastal waters of Gulf of Mannar, Palk Strait and Pondicherry ranged 0.5 - 2.83 mBq/l (mean 1.33 mBq/I), 2.14 - 32.14 mBq/l (mean 15.3 mBq/l) and 1.36 - 2.0 mBq/1 (mean 1.59 mBq/1) respectively. The sediments maintained higher level of 210 Po (mean value of 3.62 Bq/kg in Gulf of Mannar, 107.9 Bq/kg in Palk Strait and 3.0 Bq/kg in Pondicherry) than water. The 210 Po rich sediment therefore serves as a vital link in the transfer of Polonium from water to the marine organisms. The concentration of 210 Po in eight species of bivalves collected from the study area, recorded a maximum level ranging from 65.2 to 2668.9 Bq/kg in soft tissues and from 1.19 to 15.3 Bq/kg in shells. The bioaccumulation ability in bivalve species with reference to 210 Po was observed to be highly variable

  20. Polonium-210 and lead-210 in the terrestrial environment: a historical review.

    Science.gov (United States)

    Persson, Bertil R R; Holm, Elis

    2011-05-01

    The radionuclides (210)Po and (210)Pb widely present in the terrestrial environment are the final long-lived radionuclides in the decay of (238)U in the earth's crust. Their presence in the atmosphere is due to the decay of (222)Rn diffusing from the ground. The range of activity concentrations in ground level air for (210)Po is 0.03-0.3 Bq m(-3) and for (210)Pb 0.2-1.5 Bq m(-3). In drinking water from private wells the activity concentration of (210)Po is in the order of 7-48 mBq l(-1) and for (210)Pb around 11-40 mBq l(-1). From water works, however, the activity concentration for both (210)Po and (210)Pb is only in the order of 3 mBq l(-1). Mosses, lichens and peat have a high efficiency in capturing (210)Po and (210)Pb from atmospheric fallout and exhibit an inventory of both (210)Po and (210)Pb in the order of 0.5-5 kBq m(-2) in mosses and in lichens around 0.6 kBq m(-2). The activity concentrations in lichens lies around 250 Bq kg(-1), dry mass. Reindeer and caribou graze lichen which results in an activity concentration of (210)Po and (210)Pb of about 1-15 Bq kg(-1) in meat from these animals. The food chain lichen-reindeer or caribou, and Man constitutes a unique model for studying the uptake and retention of (210)Po and (210)Pb in humans. The effective annual dose due to (210)Po and (210)Pb in people with high consumption of reindeer/caribou meat is estimated to be around 260 and 132 μSv a(-1) respectively. In soils, (210)Po is adsorbed to clay and organic colloids and the activity concentration varies with soil type and also correlates with the amount of atmospheric precipitation. The average activity concentration levels of (210)Po in various soils are in the range of 20-240 Bq kg(-1). Plants become contaminated with radioactive nuclides both by absorption from the soil (supported Po) and by deposition of radioactive fallout on the plants directly (unsupported Po). In fresh leafy plants the level of (210)Po is particularly high as the result of the

  1. Polonium-210 and lead-210 in the terrestrial environment: a historical review

    International Nuclear Information System (INIS)

    Persson, Bertil R.R.; Holm, Elis

    2011-01-01

    The radionuclides 210 Po and 210 Pb widely present in the terrestrial environment are the final long-lived radionuclides in the decay of 238 U in the earth's crust. Their presence in the atmosphere is due to the decay of 222 Rn diffusing from the ground. The range of activity concentrations in ground level air for 210 Po is 0.03-0.3 Bq m -3 and for 210 Pb 0.2-1.5 Bq m -3 . In drinking water from private wells the activity concentration of 210 Po is in the order of 7-48 mBq l -1 and for 210 Pb around 11-40 mBq l -1 . From water works, however, the activity concentration for both 210 Po and 210 Pb is only in the order of 3 mBq l -1 . Mosses, lichens and peat have a high efficiency in capturing 210 Po and 210 Pb from atmospheric fallout and exhibit an inventory of both 210 Po and 210 Pb in the order of 0.5-5 kBq m -2 in mosses and in lichens around 0.6 kBq m -2 . The activity concentrations in lichens lies around 250 Bq kg -1 , dry mass. Reindeer and caribou graze lichen which results in an activity concentration of 210 Po and 210 Pb of about 1-15 Bq kg -1 in meat from these animals. The food chain lichen-reindeer or caribou, and Man constitutes a unique model for studying the uptake and retention of 210 Po and 210 Pb in humans. The effective annual dose due to 210 Po and 210 Pb in people with high consumption of reindeer/caribou meat is estimated to be around 260 and 132 μSv a -1 respectively. In soils, 210 Po is adsorbed to clay and organic colloids and the activity concentration varies with soil type and also correlates with the amount of atmospheric precipitation. The average activity concentration levels of 210 Po in various soils are in the range of 20-240 Bq kg -1 . Plants become contaminated with radioactive nuclides both by absorption from the soil (supported Po) and by deposition of radioactive fallout on the plants directly (unsupported Po). In fresh leafy plants the level of 210 Po is particularly high as the result of the direct deposition of 222 Rn

  2. The peer effect on pain tolerance.

    Science.gov (United States)

    Engebretsen, Solveig; Frigessi, Arnoldo; Engø-Monsen, Kenth; Furberg, Anne-Sofie; Stubhaug, Audun; de Blasio, Birgitte Freiesleben; Nielsen, Christopher Sivert

    2018-05-19

    Twin studies have found that approximately half of the variance in pain tolerance can be explained by genetic factors, while shared family environment has a negligible effect. Hence, a large proportion of the variance in pain tolerance is explained by the (non-shared) unique environment. The social environment beyond the family is a potential candidate for explaining some of the variance in pain tolerance. Numerous individual traits have previously shown to be associated with friendship ties. In this study, we investigate whether pain tolerance is associated with friendship ties. We study the friendship effect on pain tolerance by considering data from the Tromsø Study: Fit Futures I, which contains pain tolerance measurements and social network information for adolescents attending first year of upper secondary school in the Tromsø area in Northern Norway. Pain tolerance was measured with the cold-pressor test (primary outcome), contact heat and pressure algometry. We analyse the data by using statistical methods from social network analysis. Specifically, we compute pairwise correlations in pain tolerance among friends. We also fit network autocorrelation models to the data, where the pain tolerance of an individual is explained by (among other factors) the average pain tolerance of the individual's friends. We find a significant and positive relationship between the pain tolerance of an individual and the pain tolerance of their friends. The estimated effect is that for every 1 s increase in friends' average cold-pressor tolerance time, the expected cold-pressor pain tolerance of the individual increases by 0.21 s (p-value: 0.0049, sample size n=997). This estimated effect is controlled for sex. The friendship effect remains significant when controlling for potential confounders such as lifestyle factors and test sequence among the students. Further investigating the role of sex on this friendship effect, we only find a significant peer effect of male friends

  3. Prediction of Glucose Tolerance without an Oral Glucose Tolerance Test

    Directory of Open Access Journals (Sweden)

    Rohit Babbar

    2018-03-01

    Full Text Available IntroductionImpaired glucose tolerance (IGT is diagnosed by a standardized oral glucose tolerance test (OGTT. However, the OGTT is laborious, and when not performed, glucose tolerance cannot be determined from fasting samples retrospectively. We tested if glucose tolerance status is reasonably predictable from a combination of demographic, anthropometric, and laboratory data assessed at one time point in a fasting state.MethodsGiven a set of 22 variables selected upon clinical feasibility such as sex, age, height, weight, waist circumference, blood pressure, fasting glucose, HbA1c, hemoglobin, mean corpuscular volume, serum potassium, fasting levels of insulin, C-peptide, triglyceride, non-esterified fatty acids (NEFA, proinsulin, prolactin, cholesterol, low-density lipoprotein, HDL, uric acid, liver transaminases, and ferritin, we used supervised machine learning to estimate glucose tolerance status in 2,337 participants of the TUEF study who were recruited before 2012. We tested the performance of 10 different machine learning classifiers on data from 929 participants in the test set who were recruited after 2012. In addition, reproducibility of IGT was analyzed in 78 participants who had 2 repeated OGTTs within 1 year.ResultsThe most accurate prediction of IGT was reached with the recursive partitioning method (accuracy = 0.78. For all classifiers, mean accuracy was 0.73 ± 0.04. The most important model variable was fasting glucose in all models. Using mean variable importance across all models, fasting glucose was followed by NEFA, triglycerides, HbA1c, and C-peptide. The accuracy of predicting IGT from a previous OGTT was 0.77.ConclusionMachine learning methods yield moderate accuracy in predicting glucose tolerance from a wide set of clinical and laboratory variables. A substitution of OGTT does not currently seem to be feasible. An important constraint could be the limited reproducibility of glucose tolerance status during a

  4. Distribution and intake of polonium-210 in the environment of Goa

    International Nuclear Information System (INIS)

    Avadhani, D.N.; Mahesh, H.M.; Narayana, Y.; Siddappa, K.; Karunakara, N.; Somashekarappa, H.M.

    1999-01-01

    The paper deals with the distribution of 210 Po in soil, sand and food samples of the Goa region. The activity concentration of 210 Po in diet samples of the region were also measured and the annual effective internal dose due to ingestion of this radionuclide was estimated. The activity of 210 Po in soil and sand samples vary from 9.8 Bq kg -1 to 43.2 Bq kg -1 with a mean value of 26.3 Bq kg -1 and from 0.94 Bq kg -1 to 3.67 Bq kg -1 with the mean value of 1.82 Bq kg -1 respectively. Among food samples fish and prawn shows higher concentration of 210 Po. The committed effective dose equivalent due to veg and non-veg meals were found to be 13.49 μSvy -1 and 24.83 μSvy -1 respectively which is well below the dose limit of 1 mSvy -1 recommended by ICRP. (author)

  5. Polonium-210 and Caesium-137 in lynx (Lynx lynx), wolverine (Gulo gulo) and wolves (Canis lupus)

    International Nuclear Information System (INIS)

    Gjelsvik, Runhild; Holm, Elis; Kålås, John Atle; Persson, Bertil; Åsbrink, Jessica

    2014-01-01

    Wolves, lynx and wolverines are on the top of the food-chain in northern Scandinavia and Finland. 210 Po and 137 Cs have been analysed in samples of liver, kidney and muscle from 28 wolves from Sweden. In addition blood samples were taken from 27 wolves. In 9 of the wolves, samples of muscle, liver and blood were analysed for 210 Po. Samples of liver and muscle were collected from 16 lynx and 16 wolverines from Norway. The liver samples were analysed for 210 Po and 137 Cs. Only 137 Cs analyses were carried out for the muscle samples. The wolves were collected during the winter 2010 and 2011, while the samples for lynx and wolverines were all from 2011. The activity concentrations of 210 Po in wolves were higher for liver (range 20–523 Bq kg −1 d.w.) and kidney (range 24–942 Bq kg −1 d.w.) than muscle (range 1–43 Bq kg −1 d.w.) and blood (range 2–54 Bq kg −1 d.w.). Activity ratios, 210 Po/ 210 Pb, in wolf samples of muscle, liver and blood were in the ranges 2–77, 9–56 and 2–54. Using a wet weight ratio of 3.8 the maximal absorbed dose from 210 Po to wolf liver was estimated to 3500 μGy per year. Compared to wolf, the ranges of 210 Po in liver samples were lower in lynx (range 22–211 Bq kg −1 d.w.) and wolverine (range16–160 Bq kg −1 d.w.). Concentration of 137 Cs in wolf samples of muscle, liver, kidney and blood were in the ranges 70–8410 Bq kg −1 d.w., 36–4050 Bq kg −1 d.w., 31–3453 Bq kg −1 d.w. and 4–959 Bq kg −1 d.w., respectively. 137 Cs in lynx muscle and liver samples were in the ranges 44–13393 Bq kg −1 d.w. and 125–10260 Bq kg −1 d.w. The corresponding values for 137 Cs in wolverine were 22–3405 Bq kg −1 d.w. for liver and 53–4780 Bq kg −1 d.w. for muscle. The maximal absorbed dose from 137 Cs to lynx was estimated to 3000 μGy per year. - Highlights: • Annual doses from 210 Po are 1.4, 1.0 and 3.4 mGy for lynx, wolverine, and wolf. • Annual doses from 137 Cs are 3.3, 1.5 and 3.6 mGy for

  6. Polonium-210 and Caesium-137 in lynx (Lynx lynx), wolverine (Gulo gulo) and wolves (Canis lupus).

    Science.gov (United States)

    Gjelsvik, Runhild; Holm, Elis; Kålås, John Atle; Persson, Bertil; Asbrink, Jessica

    2014-12-01

    Wolves, lynx and wolverines are on the top of the food-chain in northern Scandinavia and Finland. (210)Po and (137)Cs have been analysed in samples of liver, kidney and muscle from 28 wolves from Sweden. In addition blood samples were taken from 27 wolves. In 9 of the wolves, samples of muscle, liver and blood were analysed for (210)Po. Samples of liver and muscle were collected from 16 lynx and 16 wolverines from Norway. The liver samples were analysed for (210)Po and (137)Cs. Only (137)Cs analyses were carried out for the muscle samples. The wolves were collected during the winter 2010 and 2011, while the samples for lynx and wolverines were all from 2011. The activity concentrations of (210)Po in wolves were higher for liver (range 20-523 Bq kg(-1) d.w.) and kidney (range 24-942 Bq kg(-1) d.w.) than muscle (range 1-43 Bq kg(-1) d.w.) and blood (range 2-54 Bq kg(-1) d.w.). Activity ratios, (210)Po/(210)Pb, in wolf samples of muscle, liver and blood were in the ranges 2-77, 9-56 and 2-54. Using a wet weight ratio of 3.8 the maximal absorbed dose from (210)Po to wolf liver was estimated to 3500 μGy per year. Compared to wolf, the ranges of (210)Po in liver samples were lower in lynx (range 22-211 Bq kg(-1) d.w.) and wolverine (range16-160 Bq kg(-1) d.w.). Concentration of (137)Cs in wolf samples of muscle, liver, kidney and blood were in the ranges 70-8410 Bq kg(-1) d.w., 36-4050 Bq kg(-1) d.w., 31-3453 Bq kg(-1) d.w. and 4-959 Bq kg(-1) d.w., respectively. (137)Cs in lynx muscle and liver samples were in the ranges 44-13393 Bq kg(-1) d.w. and 125-10260 Bq kg(-1) d.w. The corresponding values for (137)Cs in wolverine were 22-3405 Bq kg(-1) d.w. for liver and 53-4780 Bq kg(-1) d.w. for muscle. The maximal absorbed dose from (137)Cs to lynx was estimated to 3000 μGy per year. Copyright © 2014 Elsevier Ltd. All rights reserved.

  7. Isotopically tailored lead target with reduced polonium and bismuth radio-waste

    International Nuclear Information System (INIS)

    Khorasanov, G.L.; Ivanov, A.P.; Lunev, V.P.; Blokhin, A.I.

    2002-01-01

    Residual activity of a lead target after 1 year irradiation with a high power, 0.8 GeV*30 mA, proton beam is studied. It is concluded that the main radiotoxicity of irradiated lead is connected with bismuth isotope, Bi-207, which is produced in natural lead, mix of several stable isotopes, via (p,2n) reaction with Pb-208 nuclei. It is proposed to use, as a target material, lead enriched with another stable isotope, Pb-206, in order to reduce producing Bi-207 and Po-210. Estimation of charges for obtaining large quantities of lead-206 is also given. Accumulation of hazardous radionuclides, Bi-207, Bi-208, and Po-210, in natural lead to be used as a coolant in future fast reactors and accelerator driven reactors is predicted. In accelerator driven systems a large portion of Bi-207 can be produced via Pb-208(p,2n)Bi-207 reaction in a target of natural lead (Pb-208/Pb-207/Pb-206/Pb-204=52.35/22.08/24.14/1.42 %). A new isotopically tailored coolant-converter for ADS consisting of lead isotope, Pb-206, is proposed. By using this material, it is possible to reduce essentially the production of the most radio-toxic isotopes of Bi and Po and to avoid disposing the large amounts of lead. To provide the future fast reactors and accelerator driven systems with low-activation coolant - converter, the new technology of obtaining the large amounts of natural lead enriched with lead isotope, Pb-206, should be developed. (authors)

  8. Polonium-210 and lead-210 in the terrestrial environment: a historical review

    Energy Technology Data Exchange (ETDEWEB)

    Persson, Bertil R.R., E-mail: bertil_r.persson@med.lu.s [Dept. of Medical Radiation Physics, Lund University, Barngatan 2, SE-221 85 Lund (Sweden); Holm, Elis [Norwegian Radiation Protection Authority, Osteras (Norway)

    2011-05-15

    The radionuclides {sup 210}Po and {sup 210}Pb widely present in the terrestrial environment are the final long-lived radionuclides in the decay of {sup 238}U in the earth's crust. Their presence in the atmosphere is due to the decay of {sup 222}Rn diffusing from the ground. The range of activity concentrations in ground level air for {sup 210}Po is 0.03-0.3 Bq m{sup -3} and for {sup 210}Pb 0.2-1.5 Bq m{sup -3}. In drinking water from private wells the activity concentration of {sup 210}Po is in the order of 7-48 mBq l{sup -1} and for {sup 210}Pb around 11-40 mBq l{sup -1}. From water works, however, the activity concentration for both {sup 210}Po and {sup 210}Pb is only in the order of 3 mBq l{sup -1}. Mosses, lichens and peat have a high efficiency in capturing {sup 210}Po and {sup 210}Pb from atmospheric fallout and exhibit an inventory of both {sup 210}Po and {sup 210}Pb in the order of 0.5-5 kBq m{sup -2} in mosses and in lichens around 0.6 kBq m{sup -2}. The activity concentrations in lichens lies around 250 Bq kg{sup -1}, dry mass. Reindeer and caribou graze lichen which results in an activity concentration of {sup 210}Po and {sup 210}Pb of about 1-15 Bq kg{sup -1} in meat from these animals. The food chain lichen-reindeer or caribou, and Man constitutes a unique model for studying the uptake and retention of {sup 210}Po and {sup 210}Pb in humans. The effective annual dose due to {sup 210}Po and {sup 210}Pb in people with high consumption of reindeer/caribou meat is estimated to be around 260 and 132 {mu}Sv a{sup -1} respectively. In soils, {sup 210}Po is adsorbed to clay and organic colloids and the activity concentration varies with soil type and also correlates with the amount of atmospheric precipitation. The average activity concentration levels of {sup 210}Po in various soils are in the range of 20-240 Bq kg{sup -1}. Plants become contaminated with radioactive nuclides both by absorption from the soil (supported Po) and by deposition of radioactive

  9. Teaching Tolerance? Associational Diversity and Tolerance Formation

    DEFF Research Database (Denmark)

    Rapp, Carolin; Freitag, Markus

    2015-01-01

    , a closer look is taken at how associational diversity relates to the formation of tolerance and the importance of associations as schools of tolerance are evaluated. The main theoretical argument follows contact theory, wherein regular and enduring contact in diverse settings reduces prejudice and thereby...

  10. Histochemical, light and electron microscopic study of polonium-210 induced peripheral tumours in hamster lungs -evidence implicating the Clara Cell as the cell of origin

    International Nuclear Information System (INIS)

    Kennedy, A.R.; McGandy, R.B.; Little, J.B.

    1977-01-01

    Peripheral lung tumors induced in Syrian golden hamsters by intratracheally administered polonium-210 ( 210 Po) are similar to the peripheral lung tumours induced in many species by a variety of carcinogens. In addition, they show many of the histopathological features observed in human bronchiolar-alveolar carcinomas. Serial sacrifice studies of hamsters exposed to multiple instillations of 210 Po have been carried our to identify the cell of origin of these tumors. By means of thin, plastic (glycol methacrylate) sections, electron microscopy, and histochemistry, it is concluded that the bronchiolar Clara cell is the probable cell of origin, and that this view is generally compatible with many of the reported cytological characteristics of the human tumor. (author)

  11. Lactose tolerance tests

    Science.gov (United States)

    Hydrogen breath test for lactose tolerance ... Two common methods include: Lactose tolerance blood test Hydrogen breath test The hydrogen breath test is the preferred method. It measures the amount of hydrogen ...

  12. Recognition and Toleration

    DEFF Research Database (Denmark)

    Lægaard, Sune

    2010-01-01

    Recognition and toleration are ways of relating to the diversity characteristic of multicultural societies. The article concerns the possible meanings of toleration and recognition, and the conflict that is often claimed to exist between these two approaches to diversity. Different forms...... or interpretations of recognition and toleration are considered, confusing and problematic uses of the terms are noted, and the compatibility of toleration and recognition is discussed. The article argues that there is a range of legitimate and importantly different conceptions of both toleration and recognition...

  13. Fault Tolerant Feedback Control

    DEFF Research Database (Denmark)

    Stoustrup, Jakob; Niemann, H.

    2001-01-01

    An architecture for fault tolerant feedback controllers based on the Youla parameterization is suggested. It is shown that the Youla parameterization will give a residual vector directly in connection with the fault diagnosis part of the fault tolerant feedback controller. It turns out...... that there is a separation be-tween the feedback controller and the fault tolerant part. The closed loop feedback properties are handled by the nominal feedback controller and the fault tolerant part is handled by the design of the Youla parameter. The design of the fault tolerant part will not affect the design...... of the nominal feedback con-troller....

  14. TOLERANCE SENSITIVITY ANALYSIS: THIRTY YEARS LATER

    Directory of Open Access Journals (Sweden)

    Richard E. Wendell

    2010-12-01

    Full Text Available Tolerance sensitivity analysis was conceived in 1980 as a pragmatic approach to effectively characterize a parametric region over which objective function coefficients and right-hand-side terms in linear programming could vary simultaneously and independently while maintaining the same optimal basis. As originally proposed, the tolerance region corresponds to the maximum percentage by which coefficients or terms could vary from their estimated values. Over the last thirty years the original results have been extended in a number of ways and applied in a variety of applications. This paper is a critical review of tolerance sensitivity analysis, including extensions and applications.

  15. Mechanical tolerance stackup and analysis

    CERN Document Server

    Fischer, Bryan R

    2004-01-01

    BackgroundDimensioning and TolerancingTolerance Format and Decimal PlacesConverting Plus/Minus Dimensions and Tolerances into Equal Bilaterally Toleranced DimensionsVariation and Sources of VariationTolerance AnalysisWorst-case Tolerance StackupsStatistical Tolerance StackupsGeometric Dimensioning and Tolerancing (GD&T)Converting Plus/Minus Tolerancing to Positional Tolerancing and Projected Tolerance ZonesDiametral and Radial Tolerance StackupsSpecifying Material Condition Modifiers and Their Effect on Tolerance Stackups The Tolerance Stackup SketchThe Tolerance Stackup Report FormTolerance S

  16. Internal dose estimates

    International Nuclear Information System (INIS)

    Wrenn, M.E.

    1977-01-01

    Internal doses, the procedures for making them and their significance has been reviewed. Effects of uranium, radium, lead-210, polonium-210, thorium in man are analysed based on data from tables and plots. Dosimetry of some ingested nuclides and inhalation dose due to radon-222, radon-220 and their daugther products are discussed [pt

  17. Toleration out of respect?

    DEFF Research Database (Denmark)

    Lægaard, Sune

    2013-01-01

    Under conditions of pluralism different cultures, interests or values can come into conflict, which raises the problem of how to secure peaceful co-existence. The idea of toleration historically emerged as an answer to this problem. Recently Rainer Forst has argued that toleration should not just...... be based on a modus vivendi designed to secure peaceful co-existence, but should be based on moral reasons. Forst therefore advances what he calls the ‘respect conception’ of toleration as an in itself morally desirable type of relationship, which is furthermore the only conception of toleration...... that avoids various so-called ‘paradoxes of toleration’. The paper first examines whether Forst’s respect conception can be applied descriptively to distinguish between actual patterns of behaviour and classify different acts of toleration. Then the focus is shifted to toleration out of respect as a normative...

  18. Tolerance in Drosophila

    OpenAIRE

    Atkinson, Nigel S.

    2009-01-01

    The set of genes that underlie ethanol tolerance (inducible resistance) are likely to overlap with the set of genes responsible for ethanol addiction. Whereas addiction is difficult to recognize in simple model systems, behavioral tolerance is readily identifiable and can be induced in large populations of animals. Thus, tolerance lends itself to analysis in model systems with powerful genetics. Drosophila melanogaster has been used by a variety of laboratories for the identification of genes...

  19. Investigation of environmental conditions at Sarfartoq 1987-88. Collection of samples for testing, measurement of radon and analyses for polonium-210 and lead-210. [Greenland]. Miljoeundersoegelser ved Sarfartoq 1987-88. Proeveindsamling, radonmaaling og analyser for polonium-210 og bly-210

    Energy Technology Data Exchange (ETDEWEB)

    Aastrup, P; Munk Hansen, M

    1989-01-01

    The sampling of plants and animals is part of environmental base line studies initiated by the Mineral Resources Administration for Greenland in relation to plans for exploration and exploitation of a niobium occurence. Samples have been collected in areas expected to be influenced by mining activities and in reference areas. The collected species of plants include northern willow, Bellard's kobresia, lichen (Cetraria nivalis), and others. Samples of animals include musk oxen, reindeer, alpine hare, ptarmigan, fox, and arctic char. However, 60 samples have been analyzed for polonium-210 and lead-210. The highest concentrations were found in lichen and the lowest in muscle tissue. In many samples systematic differences between the concentrations of the two isotopes were observed indicating that polonium-210 should continue to be part of the base line study program and the monitoring program if mining is started. The observed concentrations pose no health problem. 30 kg bulk samples of the best pyrochlore ore and the rock c. 10 m on both sides of the mineralization (the side rock) were analyzed for niobium, tantalum, some trace elements, and natural radioactive isotopes. The ore sample has concentrations of 33.17% niobium, 0.4% tantalum, 0.77% uranium, and more than 0.37% rare earth elements. The concentrations of all other analyzed elements are low. The ore has very well defined boundaries and there is a very low concentration of radioactive elements in the side rock. The naturally occurring concentrations of radon have been measured at stations on top of the mineralization, within the carbonatite complex and outside the complex. The concentrations generally are very low. However, the concentrations in the complex are significantly higher than outside the complex. This reflects an elevated uranium concentration of the carbonatite complex rocks. (AB).

  20. Screening Prosopis (mesquite) for cold tolerance

    Energy Technology Data Exchange (ETDEWEB)

    Felker, P. (Texas AandI Univ., Kingsville); Clark, P.R.; Nash, P.; Osborn, J.F.; Cannell, G.H.

    1982-09-01

    Cold tolerance and biomass estimation of Prosopis species were examined under field conditions. Prosopis africana and P. pallida tolerated several minus 1.5/sup 0/C freezes but none survived a minus 5/sup 0/C freeze. P. alba, P. articulata, P. chilensis, P. nigra, and P. tamarugo tolerated several minus 5/sup 0/C freezes but not a 12-hour below 0/sup 0/C freeze. Most North American native species P. glandulosa var. glandulosa, P. glandulosa var. torreyana, and P. velutina tolerated the 12 hour freeze with only moderate damage. In general trees with greater productivity belonged to the most cold sensitive accessions but sufficient variability exists to substantially improve Prosopis biomass production on the coldest areas where it now naturally occurs.

  1. Compromise and Toleration

    DEFF Research Database (Denmark)

    Rostbøll, Christian F.

    Political compromise is akin to toleration, since both consist of an "agreement to disagree." Compromise and toleration also share a predicament of being regarded as ambiguous virtues that require of us to accept something we actually regard as wrong. However, we misunderstand the nature, justifi...... in compromise are more stringent than those for being tolerated. Still, the limits of compromise cannot be drawn to narrowly if it is to remain its value as a form of agreement that respects and embodies the differences of opinion in society.......Political compromise is akin to toleration, since both consist of an "agreement to disagree." Compromise and toleration also share a predicament of being regarded as ambiguous virtues that require of us to accept something we actually regard as wrong. However, we misunderstand the nature......, justification, and limits of compromise if we see it merely as a matter of toleration. While toleration is mainly a matter of accepting citizens' equal right to co-existence as subjects to law, political compromise includes the parties in making law – it makes them co-authors of law. Toleration entails...

  2. Tolerances in micro manufacturing

    DEFF Research Database (Denmark)

    Hansen, Hans Nørgaard; Zhang, Yang; Islam, Aminul

    This paper describes a method for analysis of tolerances in micro manufacturing. It proposes a mapping oftolerances to dimensions and compares this with current available international standards. The analysisdocuments that tolerances are not scaled down as the absolute dimension. In practice...

  3. Fault tolerant computing systems

    International Nuclear Information System (INIS)

    Randell, B.

    1981-01-01

    Fault tolerance involves the provision of strategies for error detection damage assessment, fault treatment and error recovery. A survey is given of the different sorts of strategies used in highly reliable computing systems, together with an outline of recent research on the problems of providing fault tolerance in parallel and distributed computing systems. (orig.)

  4. Toleration out of respect?

    DEFF Research Database (Denmark)

    Lægaard, Sune

    2014-01-01

    be based on a modus vivendi designed to secure peaceful co-existence, but should be based on moral reasons. Forst therefore advances what he calls the ‘respect conception’ of toleration as an in itself morally desirable type of relationship, which is furthermore the only conception of toleration...

  5. Recognition and Toleration

    DEFF Research Database (Denmark)

    Lægaard, Sune

    2010-01-01

    Recognition and toleration are ways of relating to the diversity characteristic of multicultural societies. The article concerns the possible meanings of toleration and recognition, and the conflict that is often claimed to exist between these two approaches to diversity. Different forms or inter...

  6. Remember Tolerance Differently

    DEFF Research Database (Denmark)

    Tønder, Lars

    2012-01-01

    This essay questions the linear conception of history which often accompanies the way contemporary democratic theory tends to disavow tolerance's discontinuities and remainders. In the spirit of Foucault's genealogy of descent, the idea is to develop a new sense of tolerance's history, not by inv......This essay questions the linear conception of history which often accompanies the way contemporary democratic theory tends to disavow tolerance's discontinuities and remainders. In the spirit of Foucault's genealogy of descent, the idea is to develop a new sense of tolerance's history......, not by invoking a critique external to contemporary democratic theory, but by witnessing the history of tolerance paraliptically, with an eye to what it obscures and yet presupposes....

  7. Methods and Data Used to Investigate Polonium-210 as a Source of Excess Gross-Alpha Radioactivity in Ground Water, Churchill County, Nevada

    Science.gov (United States)

    Seiler, Ralph L.

    2007-01-01

    Ground water is the major source of drinking water in the Carson River Basin, California and Nevada. Previous studies have shown that uranium and gross-alpha radioactivities in ground water can be greater than U.S. Environmental Protection Agency Maximum Contaminant Levels, particularly in the Carson Desert, Churchill County, Nevada. Studies also have shown that the primary source of the gross-alpha radioactivity and alpha-emitting radionuclides in ground water is the dissolution of uranium-rich granitic rocks and basin-fill sediments that have their origins in the Sierra Nevada. However, ground water sampled from some wells in the Carson Desert had gross-alpha radioactivities greater than could be accounted for by the decay of dissolved uranium. The occurrence of polonium-210 (Po-210) was hypothesized to explain the higher than expected gross-alpha radioactivities. This report documents and describes the study design, field and analytical methods, and data used to determine whether Po-210 is the source of excess gross-alpha radioactivity in ground water underlying the Carson Desert in and around Fallon, Nevada. Specifically, this report presents: 1) gross alpha and uranium radioactivities for 100 wells sampled from June to September 2001; and 2) pH, dissolved oxygen, specific conductance, and Po-210 radioactivity for 25 wells sampled in April and June 2007. Results of quality-control samples for the 2007 dataset are also presented.

  8. Assessment of the hazard to the public from anti-static brushes containing polonium-210 in the form of ceramic microspheres

    International Nuclear Information System (INIS)

    Webb, G.A.M.; Wilkins, B.T.; Wrixon, A.D.

    1975-04-01

    Anti-static brushes containing polonium-210 in the form of ceramic microspheres have been tested and evaluated with regard to their availability to the general public. After summarising existing test information, results are given of routine leakage tests and special tests intended to simulate severe but credible abuse and accidents with these devices. It is found that the low levels of removable contamination and the possible loss of complete microspheres, although in principle undesirable, do not present a significant hazard. The containment integrity of ceramic microspheres under severe conditions (impact and fire) has been found unsatisfactory and it is considered possible that ICRP dose limits could be approached or even exceeded under these severe but credible abuse, accident or disposal conditions. The results of comparative tests with nonradioactive methods for static elimination did not demonstrate any adequate justification for the use of a radioactive material. The potential exposure from Staticmaster Brushes is therefore considered an unnecessary hazard to members of the public. (author)

  9. Shape coexistence measurements in even-even neutron-deficient polonium isotopes by Coulomb excitation, using REX-ISOLDE and the Ge MINIBALL array

    CERN Multimedia

    Butler, P; Bastin, B; Kruecken, R; Voulot, D; Rahkila, P J; Orr, N A; Srebrny, J; Grahn, T; Clement, E; Paul, E S; Gernhaeuser, R A; Dorsival, A; Diriken, J V J; Huyse, M L; Iwanicki, J S

    The neutron-deficient polonium isotopes with two protons outside the closed Z=82 shell represent a set of nuclei with a rich spectrum of nucleus structure phenomena. While the onset of the deformation in the light Po isotopes is well established experimentally, questions remain concerning the sign of deformation and the magnitude of the mixing between different configurations. Furthermore, controversy is present with respect to the transition from the vibrational-like character of the heavier Po isotopes to the shape coexistence mode observed in the lighter Po isotopes. We propose to study this transition in the even-mass neutron-deficient $^{198,200,202}$Po isotopes by using post-accelerated beams from REX-ISOLDE and "safe"-energy Coulomb excitation. $\\gamma$- rays will be detected by the MINIBALL array. The measurements of the Coulomb excitation differential cross section will allow us to deduce both the transition and diagonal matrix elements for these nuclei and, combined with lifetime measurements, the s...

  10. Radioactive contamination in human by polonium-210 in food from marine origin; Contaminacao radioativa humana por Polonio-210 contido em alimento de origem marinha

    Energy Technology Data Exchange (ETDEWEB)

    Kelecom, Alphonse; Gouvea, Rita de Cassia S.; Kelecom, Philippe Marcel [Universidade Federal Fluminense, Niteroi, RJ (Brazil). Dept. de Biologia Geral. Lab. de Radiobiologia e Radiometria (LARARA)]. E-mail: egbakel@vm.uff.br

    2005-07-01

    Food from marine origin is considered as one of the sources that most contributes to internal radioactive contamination in humans by polonium-210 ({sup 210}Po). This work intended to check whether a single ingestion of the mussel Perna perna should result in a detectable increase of radioactive contamination in the consumer. The mussel was bought at a fish market localized in the city of Niteroi, RJ, Brazil. It was cooked as usually, and its content in {sup 210}Po determined after acid mineralization, spontaneous electrodeposition on stainless steel disks and alpha counting. Non-smoking volunteers maintained for two weeks a normal diet, but completely avoiding fish and seafood. Then, they ate 200 g of cooked mussel, and collected total faeces and urine every day during ten days. {sup 210}Po level in faeces samples showed a 900% increase at the first day after ingestion, and reached normal levels after 3-4 days. In urine samples, the increase of {sup 210}Po was much lower (50%) and reached a maximum at the fifth day. Such data showed a short time permanence of {sup 210}Po in the intestine. Most of ingested {sup 210}Po ({approx}91%) was eliminated in up to 5 days through faeces. A small amount was absorbed ({approx}5-10%), part of it being eliminated in urine, and the remaining contaminated the human body. (author)

  11. Polonium-210 activity concentration, transfer and dose to certain invertebrates found in the vicinity of the Kudankulam Nuclear Power Project, Tamil Nadu, India

    International Nuclear Information System (INIS)

    Benjamin, J.; Wesley, S.G.; Rajan, M.P.

    2013-01-01

    Invertebrates are significant reference organisms, and some of them tend to accumulate certain radionuclides in increased levels. It is imperative that the levels of radionuclides are measured in certain organism in the vicinity of any major nuclear power project before its commissioning; hence, this study was carried out in the surroundings of the Kudankulam Nuclear Power Project site. The natural radionuclide polonium-210 having affinity to the organic matter in the soil and to the protein content of the animals, is very significant as it delivers a high internal dose to the organisms. The activity concentration of this radionuclide, its transfer and dose were assessed in two terrestrial (earthworm, Pheretima posthuma and land snail, Trachea vittata) and two aquatic (apple snail, Pila globosa and bivalve mollusc, Lamellidens marginalis) invertebrates. The activity concentration of 210 Po was found to be the highest in the earthworm and the lowest in the land snail. The per-animal dose due to 210 Po was the highest for the apple snail and the lowest for the earthworm. The results indicate that 210 Po does not constitute a significant radiological threat to the organisms. (author)

  12. A Multirelational Account of Toleration

    DEFF Research Database (Denmark)

    Ferretti, Maria Paola; Lægaard, Sune

    2013-01-01

    Toleration classically denotes a relation between two agents that is characterised by three components: objection, power, and acceptance overriding the objection. Against recent claims that classical toleration is not applicable in liberal democracies and that toleration must therefore either be ...

  13. Delamination tolerance studies in laminated composite panels

    Indian Academy of Sciences (India)

    Abstract. Determination of levels of tolerance in delaminated composite panels is an important issue in composite structures technology. The primary intention is to analyse delaminated composite panels and estimate Strain. Energy Release Rate (SERR) parameters at the delamination front to feed into acceptability criteria.

  14. Heritability of cold tolerance in Nile tilapia, Oreochromis niloticus, juveniles

    NARCIS (Netherlands)

    Charo-Karisa, H.; Rezk, M.A.; Bovenhuis, H.; Komen, J.

    2005-01-01

    The inability of tilapia to tolerate low temperatures is of major economic concern as it reduces their growing season and leads to over winter mortality. In this study, cold tolerance of juvenile Nile tilapia, Oreochromis niloticus, was investigated and heritability estimates obtained. A total of 80

  15. Tolerance doses for treatment planning

    International Nuclear Information System (INIS)

    Lyman, J.T.

    1985-10-01

    Data for the tolerance of normal tissues or organs to (low-LET) radiation has been compiled from a number of sources which are referenced at the end of this document. This tolerance dose data are ostensibly for uniform irradiation of all or part of an organ, and are for either 5% (TD 5 ) or 50% (TD 50 ) complication probability. The ''size'' of the irradiated organ is variously stated in terms of the absolute volume or the fraction of the organ volume irradiated, or the area or the length of the treatment field. The accuracy of these data is questionable. Much of the data represents doses that one or several experienced therapists have estimated could be safely given rather than quantitative analyses of clinical observations. Because these data have been obtained from multiple sources with possible different criteria for the definition of a complication, there are sometimes different values for what is apparently the same endpoint. The data from some sources shows a tendancy to be quantized in 5 Gy increments. This reflects the size of possible round off errors. It is believed that all these data have been accumulated without the benefit of 3-D dose distributions and therefore the estimates of the size of the volume and/or the uniformity of the irradiation may be less accurate than is now possible. 19 refs., 4 figs

  16. State, religion and toleration

    DEFF Research Database (Denmark)

    Huggler, Jørgen

    2009-01-01

    Contribution to Religion and State - From separation to cooperation? Legal-philosophical reflections for a de-secularized world. (IVR Cracow Special Workshop). Eds. Bart. C. Labuschagne & Ari M. Solon. Abstract: Toleration is indeed a complex phenomenon. A discussion of the concept will have...... to underline not only the broadmindedness and liberty of individuals or of groups, but also the relevant distinctions and arguments in political philosophy, epistemology, philosophy of religion and philosophical anthropology and their connection with educational issues. Through a discussion of these relations......, the essay argues three theses: (1) Toleration is not reducible to an ethics of spiritual freedom. (2) Toleration is not neutral to fanatism. (3) Toleration involves esteem for the person....

  17. A Theory of Tolerance

    OpenAIRE

    Corneo, Giacomo; Jeanne, Olivier

    2006-01-01

    We develop an economic theory of tolerance where styles of behaviour are invested with symbolic value. Value systems are endogenous and taught by parents to their children. In conjunction with actual behaviour, value systems determine the esteem enjoyed by individuals. Intolerant individuals have all symbolic value invested in a single style of behaviour, whereas tolerant people have diversified values. The proposed model identifies a link between the unpredictability of children's lifestyles...

  18. Levels of polonium-210 in highly consumed sea foods from a fish market of the city of Niteroi, RJ-Brazil

    International Nuclear Information System (INIS)

    Marsico, Eliane T.; Sao Clemente, Sergio C. de; Kelecom, Alphonse; Gouvea, Rita de Cassia S.

    2007-01-01

    Polonium-210 ( 210 Po), a short-lived member from the uranium series, is broadly distributed in Nature being among all alpha-emitters the major contributor to the internal dose in man. Studies of diets have shown that marine foods are important sources of this radionuclide. The levels of 210 Po have been determined in three highly consumed marine species, the fishes Sardinella brasiliensis (sardine) and Thunnus atlanticus (tuna), and the shrimp Litopenaeus brasiliensis, purchased from the Niteroi (RJ, Brazil) fish market, and caught along the coast of the state of Rio de Janeiro. Doses of 210 Po were determined for the entire organisms and for some tissues and organs, such as eyes, heart, gills, muscle, stomach liver, intestine and pyloric caecal (fishes) or eyes, head content, exoskeleton, muscle, hepatopancreas and pleopods. 210 Po is not uniformly distributed within these species, the highest levels being observed for sardine in the intestine (1634.6 mBq g-1), tuna in pyloric caecal (4656.1 mBq g-1) and shrimp in the hepatopancreas (1460.5 mBq g-1). The 210 Po activities in sardine, tuna and shrimp, calculated on a mean whole-organism basis, were 64.6, 34.5 and 39.5 Bq kg-1 (dry weight) respectively, with corresponding concentration factors of 7.2 x104, 3.8 x104 and 4.4 x104. Considering body distribution, almost 60% of the total activity is concentrated in the pyloric caecal of both fishes and in the hepatopancreas of the shrimp. In turn, the edible parts concentrate much less activity. (author)

  19. Levels of polonium-210 in highly consumed sea foods from a fish market of the city of Niteroi, RJ-Brazil

    Energy Technology Data Exchange (ETDEWEB)

    Marsico, Eliane T.; Sao Clemente, Sergio C. de [Universidade Federal Fluminense (UFF), Niteroi, RJ (Brazil). Faculdade de Veterinaria. Dept. de Tecnologia de Alimentos; Kelecom, Alphonse; Gouvea, Rita de Cassia S. [Universidade Federal Fluminense (UFF), Niteroi, RJ (Brazil). Dept. de Biologia Geral. Lab. de Radiobiologia e Radiometria Pedro Lopes dos Santos - LARARA

    2007-07-01

    Polonium-210 ({sup 210}Po), a short-lived member from the uranium series, is broadly distributed in Nature being among all alpha-emitters the major contributor to the internal dose in man. Studies of diets have shown that marine foods are important sources of this radionuclide. The levels of {sup 210}Po have been determined in three highly consumed marine species, the fishes Sardinella brasiliensis (sardine) and Thunnus atlanticus (tuna), and the shrimp Litopenaeus brasiliensis, purchased from the Niteroi (RJ, Brazil) fish market, and caught along the coast of the state of Rio de Janeiro. Doses of {sup 210}Po were determined for the entire organisms and for some tissues and organs, such as eyes, heart, gills, muscle, stomach liver, intestine and pyloric caecal (fishes) or eyes, head content, exoskeleton, muscle, hepatopancreas and pleopods. {sup 210}Po is not uniformly distributed within these species, the highest levels being observed for sardine in the intestine (1634.6 mBq g-1), tuna in pyloric caecal (4656.1 mBq g-1) and shrimp in the hepatopancreas (1460.5 mBq g-1). The {sup 210}Po activities in sardine, tuna and shrimp, calculated on a mean whole-organism basis, were 64.6, 34.5 and 39.5 Bq kg-1 (dry weight) respectively, with corresponding concentration factors of 7.2 x104, 3.8 x104 and 4.4 x104. Considering body distribution, almost 60% of the total activity is concentrated in the pyloric caecal of both fishes and in the hepatopancreas of the shrimp. In turn, the edible parts concentrate much less activity. (author)

  20. Polonium-210 and Lead-210 in food and tobacco products: transfer parameters and normal exposure and dose

    International Nuclear Information System (INIS)

    Watson, A.P.

    1985-01-01

    Food-chain transport of Pb-210 and Po-210 from soil to edible plant parts and from animal feed to meat and milk was evaluated from a review of literature. The degree of transfer was characterized by estimating concentration factors as well as the transfer coefficients B/sub v/, B/sub r/, f/sub m/, and f/sub f/. Global dietary intake of Pb-210 and Po-210 was also summarized, and 50-y dose estimates to target organs were calculated. The greatest estimated ingestion doses were those to populations with large dietary complements of animal protein in the form of seafood (Japan) or caribou/reindeer muscle and organ meats (Arctic Eskimos and Lapps). The origin and magnitude of inhalation exposure and dose from tobacco products were also assessed. For the majority of internal organs evaluated, the dose resulting from smoking commercially available tobacco products is comparable with or greater than the dose estimates for ingestion of naturally occurring dietary Pb-210 and Po-210. 79 refs

  1. Escaping the tolerance trap

    International Nuclear Information System (INIS)

    Hammoudeh, S.; Madan, V.

    1994-01-01

    In order to examine the implications of the weakening of OPEC's responsiveness in adjusting its production levels, this paper explicitly incorporates rigidity in the quantity adjustment mechanism, thereby extending previous research which assumed smooth quantity adjustments. The rigidity is manifested in a tolerance range for the discrepancy between the declared target price and that of the market. This environment gives rise to a 'tolerance trap' which impedes the convergence process and inevitably brings the market to a standstill before its reaches the targeted price and revenue objectives. OPEC's reaction to the standstill has important implications for the achievement of the target-based equilibrium and for the potential collapse of the market price. This paper examines OPEC's policy options in the tolerance trap and reveals that the optional policy in order to break this impasse and move closer to the equilibrium point is gradually to reduce output and not to flood the market. (Author)

  2. Fault tolerant linear actuator

    Science.gov (United States)

    Tesar, Delbert

    2004-09-14

    In varying embodiments, the fault tolerant linear actuator of the present invention is a new and improved linear actuator with fault tolerance and positional control that may incorporate velocity summing, force summing, or a combination of the two. In one embodiment, the invention offers a velocity summing arrangement with a differential gear between two prime movers driving a cage, which then drives a linear spindle screw transmission. Other embodiments feature two prime movers driving separate linear spindle screw transmissions, one internal and one external, in a totally concentric and compact integrated module.

  3. Inequality, Tolerance, and Growth

    DEFF Research Database (Denmark)

    Bjørnskov, Christian

    This paper argues for the importance of individuals' tolerance of inequality for economic growth. By using the political ideology of governments as a measure of revealed tolerance of inequality, the paper shows that controlling for ideology improves the accuracy with which the effects of inequality...... are measured. Results show that inequality reduces growth but more so in societies where people perceive it as being relatively unfair. Further results indicate that legal quality and social trust are likely transmission channels for the effects of inequality....

  4. Inequality, Tolerance, and Growth

    DEFF Research Database (Denmark)

    Bjørnskov, Christian

    2004-01-01

    This paper argues for the importance of individuals' tolerance of inequality for economic growth. By using the political ideology of governments as a measure of revealed tolerance of inequality, the paper shows that controlling for ideology improves the accuracy with which the effects of inequality...... are measured. Results show that inequality reduces growth but more so in societies where people perceive it as being relatively unfair. Further results indicate that legal quality and social trust are likely transmission channels for the effects of inequality....

  5. Reirradiation tolerance of the rat heart

    International Nuclear Information System (INIS)

    Wondergem, Jan; Ravels, Frank J.M. van; Reijnart, Ivonne W.C.; Strootman, Erwin G.

    1996-01-01

    Purpose: To investigate the influence of reirradiation on the tolerance of the heart after a previous irradiation treatment. Methods and Materials: Female Wistar rats were locally irradiated to the thorax. Development of cardiac function loss was studied with the ex vivo working rat heart preparation. To compare the retreatment experiments, initial, and reirradiation doses were expressed as the percentage of the extrapolated tolerance dose (ETD). Results: Local heart irradiation with a single dose led to a dose-dependent and progressive decrease in cardiac function. The progressive nature of irradiation-induced heart disease is shown to affect the outcome of the retreatment, depending on both the time interval between subsequent doses and the size of the initial dose. The present data demonstrate that hearts are capable of repairing a large part of the initial dose of 10 Gy within the first 24 h. However, once biological damage as a result of the first treatment is fixed, the heart does not show any long-term recovery. At intervals up to 6 months between an initial treatment with 10 Gy and subsequent reirradiation, the reirradiation tolerance dose slightly decreased from 74% of the ETD ref (at 24-h interval) to 68% of the ETD ref (at 6-month interval). Between 6 and 9 months, reirradiation tolerance dose dropped more even to 43% of the ETD ref . Treatment of the heart with an initial dose of 17.5 Gy, instead of 10 Gy, 6 months prior to reirradiation, also led to a further decrease of the reirradiation tolerance dose ( ref ). Conclusions: The outcome of the present study shows a decreased tolerance of the heart to reirradiation at long time intervals (interval > 6 months). This has clinical implications for the estimation of reirradiation tolerance in patients whose mediastinum has to be reirradiated a long time after a first irradiation course

  6. Determination of uranium and thorium isotopes and polonium in sediment profiles from Baixada Santista, SP; Determinacao de isotopos de uranio e torio e polonio em perfis de sedimento da Baixada Santista, SP

    Energy Technology Data Exchange (ETDEWEB)

    Ramos, Guilherme da Franca

    2010-07-01

    The objective of the present work is to determine the activity concentration of uranium and thorium isotopes and polonium in estuarine sediments from Baixada Santista. The area comprehends nine cities in the Brazilian coast (Bertioga, Guaruja, Santos, Sao Vicente, Cubatao, Praia Grande, Mongagua, Itanhaem and Peruibe). It is one of the most important industrial areas in Brazil due to the large number of industries operating in Cubatao, such as steel, petrochemical and fertilizer industries. That, together with a large population, causes a negative impact on the marine biota. In the present work 10 profiles of sediment cores, with depth varying from 41 to 98 cm, were analyzed. The cores were obtained from Santos, Cubatao, Sao Vicente and Bertioga. The cores were sliced every 2 cm and were treated with both physical and chemical processes, including drying, grinding and sieving. The samples were dissolved by acid digestion, till total dissolution and destruction of organic matter. After the acid digestion, the samples were filtered and evaporated till dryness. The radiochemical techniques used to separate the radionuclides and to prepare the final source for alpha counting were ion exchange chromatography and spontaneous deposition for polonium and electrodeposition for U and Th. The final sources were counted in a surface barrier alpha spectrometer. Values obtained for the radionuclides analyzed were similar to the activity concentrations of sediments in non polluted areas, with the exception of a few samples that showed anthropic influence. (author)

  7. Distribution of radionuclide in Cauvery River Basin, South Interior Karnataka, India

    International Nuclear Information System (INIS)

    Kavitha, E.; Chandrashekara, M.S.; Paramesh, L.

    2015-01-01

    Radium, radon and polonium are the most important isotopes from the radiological point of view in the uranium decay series. The concentrations of radium, radon and polonium were studied in water samples of Kodagu, Mandya, Mysuru, Hassan and Chamarajanagara districts. The study area lies between 10°05'N to 13°30' N latitudes and 75°30' E to 79°45' E longitudes. Polonium in water was estimated using radiochemical analysis. Higher concentration of polonium in water was observed at Kushalnagara region (3.35 mBqL -1 ), lower value was found near Mysuru (1.54 mBqL -1 ) -and the average polonium concentration in the study region was (2.49 mBqL -1 ). The radium-226 was analysed using Emanometry method. Higher concentration of radium-226 was found near Abbi falls of Kodagu district (73.0 mBqL -1 ), lower value was found in Srirangapatna of Mandya district (2.20 mBqL -1 ) and the average was 36.12 mBqL -1 . W.H.O and UNSCEAR have given the tolerable dose range for different radioactive elements. If the estimated value crosses this range then it would cause certain health hazards. The values obtained in the present study are comparable to the value of polonium, radium and radon in water reported in literature. (author)

  8. The polonium 210 in aerosols: contribution to the study of savannah fires and volcano emissions; Le polonium 210 dans les aerosols: contribution a l`etude des feux de savanes et des emissions volcaniques

    Energy Technology Data Exchange (ETDEWEB)

    Nho-Kim, E.Y

    1996-06-27

    Natural sources plan a fundamental role on the emission of the species causing climatic variations. The aim of this study is, on the one hand, to estimate fluxes of different components emitted by biomass burning and volcanoes, and on the other hand, to trace these components in time and space. We used {sup 210}Po, last decay product in the {sup 238}U series, as a tracer, as it is one of the characteristic species emitted by these sources: it is highly enriched in these plumes compared to the usual atmosphere and the {sup 210}Po radioactivity is not affected by chemical transformation. We have shown that the contribution of biomass burning on the {sup 210}Po concentration in local background atmosphere is minor during the dry season, compared to that of Saharan soil dusts despite of the importance of this source in the global budget of {sup 210}Po (10%). However, the good correlation observed between the {sup 210}Po concentration and that of carbonaceous aerosols and of CO{sub 2} in biomass burning plumes reveals that {sup 210}Po can be used as a reference of the components emitted by biomass burning. We have estimated the contribution of the Indonesian volcanoes which represent about 5 to 30 % of the global volcanic budget of trace metals. Atmospheric transport of these volcanic plumes was simulated using the {sup 210}Po as a tracer. Due to the characteristic atmospheric circulation in this region, vertical transport is predominant over meridian dispersion, which is moderated by the convergence of the trade winds. The impact of these volcanic emissions on the atmospheric concentration of the trace metals remains a local effect when the volcanic activity is out of cataclysmal eruptions. (author)

  9. Lead-210, bismuth-210, polonium-210. Natural activity, internal dosimetry, and dose factors for ingestion and inhalation

    International Nuclear Information System (INIS)

    Jacobi, W.

    1979-02-01

    Starting with a comprehensive review of the normal, natural activity of 210 Pb and 210 Po in the environment and in the tissues of the human body, a model of the activity and dose distributions of this nuclides in the human body is developed. Dose factors for ingestion with food and for inhalation are derived from this model, related to the intake rate unit. This 'natural exposure model' can be used for an estimation of the population exposure due to normal natural radiation as well as to man-made sourcess of these nuclides, e.g. coal-fired power plants. (orig.) [de

  10. Melhoramento do trigo: X. Estimativas da herdabilidade e correlações entre tolerância à toxicidade de alumínio e produção de grãos com outros caracteres agronômicos em trigo Wheat breeding: X. Heritability estimates and associations of tolerance to aluminum toxicity and grain yield with other agronomic characteristics in wheat

    Directory of Open Access Journals (Sweden)

    Carlos Eduardo de Oliveira Camargo

    1984-01-01

    plantas (com exceção da Alondra S-46 x IAC-5, produção de grãos e número de grãos por espigueta, sugerindo que seria possível selecionar plantas tolerantes ao Al3+, de porte médio, com maior fertilidade da espiga e com o potencial produtivo do cultivar Alondra-S-46.High grain yield potential, and Al sensitive cultivar Alondra S-46 was crossed with standard height, low grain yield potential, Al tolerant cultivars IAC-5, BH-1146 and C-3. Parents, F1's, F2's and reciprocal backcrosses were tested for their seedling reaction to 6 ppm of Al3+ in nutrient solution. Grain yield, plant height, number of spikes per plant, number of spikelets per spike, number of grains per spike, number of grains per spikelet, 100-grain-weight and spike length were determined for the same populations at maturity. Narrow sense heritability estimates were high for spike length, number of grains per spike, 100-grain-weight, and plant height; moderate for number of spikes per plant and number of spikelets per spike; and low for the rest of the agronomic characteristics under study. Additive effects were the main source of genetic variation for spike length, plant height, number of grains per spike and 100-grain-weight. Grain yield of the studied populations was significantly correlated with all the agronomic characteristics under study except the number of spikelets per spike. Tolerance to Al3+ toxicity was not associated with plant height (except for the population from the cross Alondra S-46 x IAC-5, grain yield and number of grains per spikelet (spike fertility. The results suggested that there is a possibility of selecting plant types that combine Al3+ tolerance, semi-dwarf height levels and high yield potential, to be grown on acid soils

  11. Toleration, Groups, and Multiculturalism

    DEFF Research Database (Denmark)

    Lægaard, Sune

    2014-01-01

    have the ability to interfere with the group’s activities, an object of dislike or disapproval, an agent enjoying non-interference or a moral patient. This means that 'toleration of groups' can mean quite different things depending on the exact meaning of 'group' in relation to each component...

  12. Fault Tolerant Control Systems

    DEFF Research Database (Denmark)

    Bøgh, S. A.

    This thesis considered the development of fault tolerant control systems. The focus was on the category of automated processes that do not necessarily comprise a high number of identical sensors and actuators to maintain safe operation, but still have a potential for improving immunity to component...

  13. Toleration and its enemies

    DEFF Research Database (Denmark)

    Jarvad, Ib Martin

    2010-01-01

    After a presentation of the development of freedom of expression in Danish constitutional law, to freedom of the press in European human rights law - the Jersild case- to a right to mock and ridicule other faiths in recent Danish practice, the essay of Locke on toleration is examined, its...

  14. A little toleration, please

    Science.gov (United States)

    McKnight, C.

    2000-01-01

    Value pluralism does not imply relativism or subjectivism about values. What it does is allow respect for an at least limited toleration of values with which one may profoundly disagree. Thus a doctor can respect the autonomy of a patient whose values he does not share. Key Words: Pluralism • multiculturalism • relativism • subjectivism • patient autonomy PMID:11129842

  15. Deconstructing tolerance with clobazam

    Science.gov (United States)

    Wechsler, Robert T.; Sankar, Raman; Montouris, Georgia D.; White, H. Steve; Cloyd, James C.; Kane, Mary Clare; Peng, Guangbin; Tworek, David M.; Shen, Vivienne; Isojarvi, Jouko

    2016-01-01

    Objective: To evaluate potential development of tolerance to adjunctive clobazam in patients with Lennox-Gastaut syndrome. Methods: Eligible patients enrolled in open-label extension study OV-1004, which continued until clobazam was commercially available in the United States or for a maximum of 2 years outside the United States. Enrolled patients started at 0.5 mg·kg−1·d−1 clobazam, not to exceed 40 mg/d. After 48 hours, dosages could be adjusted up to 2.0 mg·kg−1·d−1 (maximum 80 mg/d) on the basis of efficacy and tolerability. Post hoc analyses evaluated mean dosages and drop-seizure rates for the first 2 years of the open-label extension based on responder categories and baseline seizure quartiles in OV-1012. Individual patient listings were reviewed for dosage increases ≥40% and increasing seizure rates. Results: Data from 200 patients were included. For patients free of drop seizures, there was no notable change in dosage over 24 months. For responder groups still exhibiting drop seizures, dosages were increased. Weekly drop-seizure rates for 100% and ≥75% responders demonstrated a consistent response over time. Few patients had a dosage increase ≥40% associated with an increase in seizure rates. Conclusions: Two-year findings suggest that the majority of patients do not develop tolerance to the antiseizure actions of clobazam. Observed dosage increases may reflect best efforts to achieve seizure freedom. It is possible that the clinical development of tolerance to clobazam has been overstated. ClinicalTrials.gov identifier: NCT00518713 and NCT01160770. Classification of evidence: This study provides Class III evidence that the majority of patients do not develop tolerance to clobazam over 2 years of treatment. PMID:27683846

  16. A statistical approach to investigating enhancement of polonium-210 in the Eastern Irish Sea arising from discharges from a former phosphate processing plant.

    Science.gov (United States)

    Dewar, Alastair; Camplin, William; Barry, Jon; Kennedy, Paul

    2014-12-01

    Since the cessation of phosphoric acid production (in 1992) and subsequent closure and decommissioning (2004) of the Rhodia Consumer Specialties Limited plant in Whitehaven, the concentration levels of polonium-210 ((210)Po) in local marine materials have declined towards a level more typical of natural background. However, enhanced concentrations of (210)Po and lead-210 ((210)Pb), due to this historic industrial activity (plant discharges and ingrowth of (210)Po from (210)Pb), have been observed in fish and shellfish samples collected from this area over the last 20 years. The results of this monitoring, and assessments of the dose from these radionuclides, to high-rate aquatic food consumers are published annually in the Radioactivity in Food and the Environment (RIFE) report series. The RIFE assessment uses a simple approach to determine whether and by how much activity is enhanced above the normal background. As a potential tool to improve the assessment of enhanced concentrations of (210)Po in routine dose assessments, a formal statistical test, where the null hypothesis is that the Whitehaven area is contaminated with (210)Po, was applied to sample data. This statistical, modified "green", test has been used in assessments of chemicals by the OSPAR commission. It involves comparison of the reported environmental concentrations of (210)Po in a given aquatic species against its corresponding Background Assessment Concentration (BAC), which is based upon environmental samples collected from regions assumed to be not enhanced by industrial sources of (210)Po, over the period for which regular monitoring data are available (1990-2010). Unlike RIFE, these BAC values take account of the variability of the natural background level. As an example, for 2010 data, crab, lobster, mussels and winkles passed the modified "green" test (i.e. the null hypothesis is rejected) and as such are deemed not to be enhanced. Since the cessation of phosphoric acid production in 1992

  17. Heat tolerance in wheat

    DEFF Research Database (Denmark)

    Sharma, Dew Kumari

    As a consequence of global climate change, heat stress together with other abiotic stresses will remain an important determinant of future food security. Wheat (Triticum aestivum L.) is the third most important crop of the world feeding one third of the world population. Being a crop of temperate...... climate, wheat is sensitive to heat stress. We need to understand how our crops will perform in these changing climatic conditions and how we can develop varieties, which are more tolerant. The PhD study focussed on understanding heat tolerance in wheat with a combined approach of plant physiology...... and quantitative genetics in particular, plant phenotyping based quantitative trait loci (QTL) discovery for a physiological trait under heat stress. Chlorophyll a fluorescence trait, Fv/Fm was used as a phenotyping tool, as it reflects the effect of heat stress on maximum photochemical efficiency of photosystem...

  18. Socially-Tolerable Discrimination

    OpenAIRE

    Amegashie, J. Atsu

    2008-01-01

    History is replete with overt discrimination on the basis of race, gender, age, citizenship, ethnicity, marital status, academic performance, health status, volume of market transactions, religion, sexual orientation, etc. However, these forms of discrimination are not equally tolerable. For example, discrimination based on immutable or prohibitively unalterable characteristics such as race, gender, or ethnicity is much less acceptable. Why? I develop a simple rent-seeking model of conflict w...

  19. 210-Polonium studies in some environmental and biological matrices of Domiasiat uranium deposit area, West Khasi Hills, Meghalaya, India.

    Science.gov (United States)

    Marbaniang, Deswyn G; Poddar, Raj K; Nongkynrih, Phlis; Khathing, Darlando T

    2010-03-01

    The study was performed using a silicon surface barrier alpha spectrometer at Bhabha Atomic Research Centre, Mumbai, India. Through the study, the observed (210)Po activity in water sample from different locations in the Domiasiat area ranges from 0.04 to 0.69 Bq/l. The daily and annual intake of (210)Po through water was also estimated and the mean value of 0.72 and 263.61 Bq, respectively, were observed. It is observed that the effective doses through water were higher than the World Health Organization recommended dose of 0.05 mSv/year. The total annual effective doses through terrestrial ingestion for all the locations was studied and the mean annual effective dose was observed to be 0.315 mSv, which, when compared to the worldwide and the Indian values, was observed to be slightly higher. The mean activity in soil is found to be 124.8 +/-5.7 Bq/kg and in meat the activity is 0.43 +/-0.05 Bq/kg. In fishes, an activity of 0.48 +/-0.07 Bq/kg in Garra lamta, 0.29 +/-0.02 Bq/kg in Neolissocheilus hexaganolepis, and 3.3 +/-0.1 Bq/kg in Macrobrachium sp. is observed. Activity concentration in plant samples was analyzed and the activity ranges from 0.020 +/-0.002 to 9.69 +/-0.35 Bq/kg. Committed effective dose by the adult population of the Domiasiat area through intake of (210)Po through these food items was also determined and compared with the Indian average value and the worldwide average value.

  20. Polonium-210 and lead-210 in the Southern Polar Ocean: Naturally occurring tracers of biological and hydrographical processes in the surface waters of the Antarctic Circumpolar Current and the Weddell Sea; Polonium-210 und Blei-210 im Suedpolarmeer: Natuerliche Tracer fuer biologische und hydrographische Prozesse im Oberflaechenwasser des Antarktischen Zirkumpolarstroms und des Weddellmeeres

    Energy Technology Data Exchange (ETDEWEB)

    Friedrich, J.

    1997-11-01

    In this thesis the distribution of {sup 210}Po and {sup 210}Pb in the upper 600 m of the Antarctic Circumpolar Current and the Weddell Sea was investigated along north-south transects in austral spring and autumn. {sup 210}Po and {sup 210}Pb can serve as sensitive tracers for the special hydrographic conditions of the Antarctic Circumpolar Current and the Weddell Sea as well as for biological processes during phytoplankton blooms. The {sup 210}Po/{sup 210}Pb disequilibrium was used as a tracer for particle export. This tracer integrates export on a timescale of 276 days because of the 138 day half-life of {sup 210}Po and complements the {sup 234}Th/{sup 238}U disequilibrium as another tracer for plankton production and export on a shorter timescale of several weeks. (orig.) [Deutsch] In der vorliegenden Arbeit wurde die Verteilung von Blei-210 und seinem Enkelnuklid Polonium-210 im Antarktischen Zirkumpolarstrom und im Weddellmeer bis 600 m Tiefe in mehreren meridionalen Transekten im australen Fruehjahr und Herbst waehrend der `Polarstern`-Expeditionen ANT-X/6 und ANT-XI/4 untersucht. Die Verteilung von {sup 210}Pb und {sup 210}Po wird von mehreren Faktoren beeinflusst, sowohl durch die Advektion von Wassermassen im Antarktischen Zirkumpolarstrom und im Weddellmeer als auch von biologischen Prozessen z.B. innerhalb einer Planktonbluete. Bevor die Verteilungsmuster von {sup 210}Pb und {sup 210}Po jedoch als Tracer fuer einen Prozess genutzt werden koennen, muss der Effekt der einzelnen Faktoren auf die Verteilung betrachtet werden. (orig.)

  1. Fault Tolerant Computer Architecture

    CERN Document Server

    Sorin, Daniel

    2009-01-01

    For many years, most computer architects have pursued one primary goal: performance. Architects have translated the ever-increasing abundance of ever-faster transistors provided by Moore's law into remarkable increases in performance. Recently, however, the bounty provided by Moore's law has been accompanied by several challenges that have arisen as devices have become smaller, including a decrease in dependability due to physical faults. In this book, we focus on the dependability challenge and the fault tolerance solutions that architects are developing to overcome it. The two main purposes

  2. Toleration, Synthesis or Replacement?

    DEFF Research Database (Denmark)

    Holtermann, Jakob v. H.; Madsen, Mikael Rask

    2016-01-01

    , in order to answer is not yet another partisan suggestion, but rather an attempt at making intelligible both the oppositions and the possibilities of synthesis between normative and empirical approaches to law. Based on our assessment and rational reconstruction of current arguments and positions, we...... therefore outline a taxonomy consisting of the following three basic, ideal-types in terms of the epistemological understanding of the interface of law and empirical studies: toleration, synthesis and replacement. This tripartite model proves useful with a view to teasing out and better articulating...

  3. Ethnopoly promotes tolerance

    CERN Document Server

    CERN Bulletin

    2010-01-01

    On Friday 23 April, 225 primary school children from the eight schools in Meyrin-Cointrin and their accompanying adults took part in a big game of Ethnopoly. Private individuals, associations, administrations, shopkeepers and CERN all opened their doors to them to talk about their countries, their customs and what they are doing to promote tolerance and integration.   The CERN stand set up at ForumMeyrin for the Ethnopoly game. Scurrying from one place to another, the 10 and 11 year olds were made aware of the rich cultural diversity of their commune, which is home to 130 different nationalities. Physicists and engineers from CERN took up residence in the Forum Meyrin for the day in order to talk to the children about the advantages of international collaboration, a subject dear to the Organization's heart. They welcomed around fifty children in the course of the day, conveying to them a message of tolerance: despite their differences, the 10,000 scientists and other members of the CERN...

  4. A Consideration of Resistance and Tolerance for Ruminant Nematode Infections

    Directory of Open Access Journals (Sweden)

    Steve eBishop

    2012-12-01

    Full Text Available Debates on the relative merits of resistance (the ability of the host to control the parasite lifecycle and tolerance (the net impact of infection on host performance are often lively and unhindered by data or evidence. Resistance generally shows continuous, heritable variation but data are sparser for tolerance, the utility of which will depend upon the disease prevalence. Prevalence is a function of group mean resistance and infection pressure, which itself is influenced by mean resistance. Tolerance will have most value for endemic diseases with a high prevalence, but will be of little value for low prevalence diseases. The conditionality of tolerance on infection status, and hence resistance, makes it difficult to estimate independently of resistance.Tolerance is potentially tractable for nematode infections, as the prevalence of infection is ca. 100% in animals grazing infected pasture, and infection level can be quantified by faecal egg count (FEC. Whilst individual animal phenotypes for tolerance are difficult to estimate, breeding values are estimable if related animals graze pastures of different contamination levels. Selection for resistance, i.e. FEC, provides both direct and indirect benefits from ever decreased pasture contamination and hence decreased infectious challenge. Modelling and experimental studies have shown that such reductions in pasture contamination may lead to substantially increased performance.It is proposed that selection goals addressing nematode infections should include both resistance and performance under challenging conditions. However, there may be benefits from exploiting large datasets in which sires are used across cohorts differing in infection level, to further explore tolerance. This may help to customise breeding objectives, with tolerance given greater weight in heavily parasitized environments.

  5. Fault-tolerant computing systems

    International Nuclear Information System (INIS)

    Dal Cin, M.; Hohl, W.

    1991-01-01

    Tests, Diagnosis and Fault Treatment were chosen as the guiding themes of the conference. However, the scope of the conference included reliability, availability, safety and security issues in software and hardware systems as well. The sessions were organized for the conference which was completed by an industrial presentation: Keynote Address, Reconfiguration and Recover, System Level Diagnosis, Voting and Agreement, Testing, Fault-Tolerant Circuits, Array Testing, Modelling, Applied Fault Tolerance, Fault-Tolerant Arrays and Systems, Interconnection Networks, Fault-Tolerant Software. One paper has been indexed separately in the database. (orig./HP)

  6. Commercialization of radiation tolerant camera

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Yong Bum; Choi, Young Soo; Kim, Sun Ku; Lee, Jong Min; Cha, Bung Hun; Lee, Nam Ho; Byun, Eiy Gyo; Yoo, Seun Wook; Choi, Bum Ki; Yoon, Sung Up; Kim, Hyun Gun; Sin, Jeong Hun; So, Suk Il

    1999-12-01

    In this project, radiation tolerant camera which tolerates 10{sup 6} - 10{sup 8} rad total dose is developed. In order to develop radiation tolerant camera, radiation effect of camera components was examined and evaluated, and camera configuration was studied. By the result of evaluation, the components were decided and design was performed. Vidicon tube was selected to use by image sensor and non-browning optics and camera driving circuit were applied. The controller needed for CCTV camera system, lens, light, pan/tilt controller, was designed by the concept of remote control. And two type of radiation tolerant camera were fabricated consider to use in underwater environment or normal environment. (author)

  7. Commercialization of radiation tolerant camera

    International Nuclear Information System (INIS)

    Lee, Yong Bum; Choi, Young Soo; Kim, Sun Ku; Lee, Jong Min; Cha, Bung Hun; Lee, Nam Ho; Byun, Eiy Gyo; Yoo, Seun Wook; Choi, Bum Ki; Yoon, Sung Up; Kim, Hyun Gun; Sin, Jeong Hun; So, Suk Il

    1999-12-01

    In this project, radiation tolerant camera which tolerates 10 6 - 10 8 rad total dose is developed. In order to develop radiation tolerant camera, radiation effect of camera components was examined and evaluated, and camera configuration was studied. By the result of evaluation, the components were decided and design was performed. Vidicon tube was selected to use by image sensor and non-browning optics and camera driving circuit were applied. The controller needed for CCTV camera system, lens, light, pan/tilt controller, was designed by the concept of remote control. And two type of radiation tolerant camera were fabricated consider to use in underwater environment or normal environment. (author)

  8. Salt Tolerance in Soybean

    Institute of Scientific and Technical Information of China (English)

    Tsui-Hung Phang; Guihua Shao; Hon-Ming Lam

    2008-01-01

    Soybean is an Important cash crop and its productivity is significantly hampered by salt stress. High salt Imposes negative impacts on growth, nodulation, agronomy traits, seed quality and quantity, and thus reduces the yield of soybean. To cope with salt stress, soybean has developed several tolerance mechanisms, including: (I) maintenance of ion homeostasis; (ii) adjustment in response to osmotic stress; (iii) restoration of osmotic balance; and (iv) other metabolic and structural adaptations. The regulatory network for abiotic stress responses in higher plants has been studied extensively in model plants such as Arabidopsis thaliana. Some homologous components involved in salt stress responses have been identified in soybean. In this review, we tried to integrate the relevant works on soybean and proposes a working model to descdbe Its salt stress responses at the molecular level.

  9. Delay tolerant networks

    CERN Document Server

    Gao, Longxiang; Luan, Tom H

    2015-01-01

    This brief presents emerging and promising communication methods for network reliability via delay tolerant networks (DTNs). Different from traditional networks, DTNs possess unique features, such as long latency and unstable network topology. As a result, DTNs can be widely applied to critical applications, such as space communications, disaster rescue, and battlefield communications. The brief provides a complete investigation of DTNs and their current applications, from an overview to the latest development in the area. The core issue of data forward in DTNs is tackled, including the importance of social characteristics, which is an essential feature if the mobile devices are used for human communication. Security and privacy issues in DTNs are discussed, and future work is also discussed.

  10. Casualty Estimation for Nuclear and Radiological Weapons

    Science.gov (United States)

    2016-06-01

    rate 2.69 d β Metal Polonium - 210 210Po Static eliminators 138 d α Metal foil Radium-226 226Ra Brachytherapy - low dose rate 1600 y α Salt...Promethium-147 153Gd Gadolinium-153 169Yb Ytterbium-169 170Tm Thulium-170 192Ir Iridium-192 210Po Polonium - 210 226Ra Radium-226 238Pu Plutonium-238...Brussels: NATO, in development). iv present in a large food irradiator facility, and constitutes about 34.5 kg of 137Cs. To illustrate alternative

  11. Shaping tolerant attitudes towards immigrants

    DEFF Research Database (Denmark)

    Rapp, Carolin

    2017-01-01

    This article contributes to the ongoing discussion on how tolerance may be fostered in Western European countries and to the question of how contextual factors such as welfare state expenditures may contribute to this formation. Tolerance is understood as a basic democratic principle that helps c...

  12. Legal Quality, Inequality, and Tolerance

    DEFF Research Database (Denmark)

    Bjørnskov, Christian

    Previous findings suggest that income inequality leads to lower legal quality. This paper argues that voters' tolerance of inequality exerts an additional influence. Empirical findings suggest that inequality leads to lower legal quality due to its effect on trust while the tolerance of inequality...

  13. Legal Quality, Inequality, and Tolerance

    DEFF Research Database (Denmark)

    Bjørnskov, Christian

    2004-01-01

    Previous findings suggest that income inequality leads to lower legal quality. This paper argues that voters' tolerance of inequality exerts an additional influence. Empirical findings suggest that inequality leads to lower legal quality due to its effect on trust while the tolerance of inequality...

  14. Tolerance Issue in Kazakh Culture

    Science.gov (United States)

    Aubakirova, Saltanat S.; Ismagambetova, Zukhra N.; Karabayeva, Aliya G.; Rysbekova, Shamshiya S.; Mirzabekova, Alma Sh.

    2016-01-01

    In this article the authors reveal the basic cultural mechanisms that influence the formation of the tolerance strategy in Kazakh and Kazakhstan society, show its basic directions, as well as its importance for the modern Kazakhstan society and the formation of intercultural communication with foreign countries. Tolerance is a necessary element of…

  15. Tolerance-Based Feature Transforms

    NARCIS (Netherlands)

    Reniers, Dennie; Telea, Alexandru

    2007-01-01

    Tolerance-based feature transforms (TFTs) assign to each pixel in an image not only the nearest feature pixels on the boundary (origins), but all origins from the minimum distance up to a user-defined tolerance. In this paper, we compare four simple-to-implement methods for computing TFTs on binary

  16. The DESCARTES-Nantes survey of kidney transplant recipients displaying clinical operational tolerance identifies 35 new tolerant patients and 34 almost tolerant patients.

    Science.gov (United States)

    Massart, Annick; Pallier, Annaïck; Pascual, Julio; Viklicky, Ondrej; Budde, Klemens; Spasovski, Goce; Klinger, Marian; Sever, Mehmet Sukru; Sørensen, Søren Schwartz; Hadaya, Karine; Oberbauer, Rainer; Dudley, Christopher; De Fijter, Johan W; Yussim, Alexander; Hazzan, Marc; Wekerle, Thomas; Berglund, David; De Biase, Consuelo; Pérez-Sáez, María José; Mühlfeld, Anja; Orlando, Giuseppe; Clemente, Katia; Lai, Quirino; Pisani, Francesco; Kandus, Aljosa; Baas, Marije; Bemelman, Frederike; Ponikvar, Jadranka Buturovic; Mazouz, Hakim; Stratta, Piero; Subra, Jean-François; Villemain, Florence; Hoitsma, Andries; Braun, Laura; Cantarell, Maria Carmen; Colak, Hulya; Courtney, Aisling; Frasca, Giovanni Maria; Howse, Matthew; Naesens, Maarten; Reischig, Tomas; Serón, Daniel; Seyahi, Nurhan; Tugmen, Cem; Alonso Hernandez, Angel; Beňa, Luboslav; Biancone, Luigi; Cuna, Vania; Díaz-Corte, Carmen; Dufay, Alexandre; Gaasbeek, André; Garnier, Arnaud; Gatault, Philippe; Gentil Govantes, Miguel Angel; Glowacki, François; Gross, Oliver; Hurault de Ligny, Bruno; Huynh-Do, Uyen; Janbon, Bénédicte; Jiménez Del Cerro, Luis Antonio; Keller, Frieder; La Manna, Gaetano; Lauzurica, Ricardo; Le Monies De Sagazan, Hervé; Thaiss, Friedrich; Legendre, Christophe; Martin, Séverine; Moal, Marie-Christine; Noël, Christian; Pillebout, Evangeline; Piredda, Gian Benedetto; Puga, Ana Ramírez; Sulowicz, Wladyslaw; Tuglular, Serhan; Prokopova, Michaela; Chesneau, Mélanie; Le Moine, Alain; Guérif, Pierrick; Soulillou, Jean-Paul; Abramowicz, Marc; Giral, Magali; Racapé, Judith; Maggiore, Umberto; Brouard, Sophie; Abramowicz, Daniel

    2016-06-01

    Kidney recipients maintaining a prolonged allograft survival in the absence of immunosuppressive drugs and without evidence of rejection are supposed to be exceptional. The ERA-EDTA-DESCARTES working group together with Nantes University launched a European-wide survey to identify new patients, describe them and estimate their frequency for the first time. Seventeen coordinators distributed a questionnaire in 256 transplant centres and 28 countries in order to report as many 'operationally tolerant' patients (TOL; defined as having a serum creatinine <1.7 mg/dL and proteinuria <1 g/day or g/g creatinine despite at least 1 year without any immunosuppressive drug) and 'almost tolerant' patients (minimally immunosuppressed patients (MIS) receiving low-dose steroids) as possible. We reported their number and the total number of kidney transplants performed at each centre to calculate their frequency. One hundred and forty-seven questionnaires were returned and we identified 66 TOL (61 with complete data) and 34 MIS patients. Of the 61 TOL patients, 26 were previously described by the Nantes group and 35 new patients are presented here. Most of them were noncompliant patients. At data collection, 31/35 patients were alive and 22/31 still operationally tolerant. For the remaining 9/31, 2 were restarted on immunosuppressive drugs and 7 had rising creatinine of whom 3 resumed dialysis. Considering all patients, 10-year death-censored graft survival post-immunosuppression weaning reached 85% in TOL patients and 100% in MIS patients. With 218 913 kidney recipients surveyed, cumulative incidences of operational tolerance and almost tolerance were estimated at 3 and 1.5 per 10 000 kidney recipients, respectively. In kidney transplantation, operational tolerance and almost tolerance are infrequent findings associated with excellent long-term death-censored graft survival. © The Author 2016. Published by Oxford University Press on behalf of ERA-EDTA. All rights reserved.

  17. Tolerable Time-Varying Overflow on Grass-Covered Slopes

    Directory of Open Access Journals (Sweden)

    Steven A. Hughes

    2015-03-01

    Full Text Available Engineers require estimates of tolerable overtopping limits for grass-covered levees, dikes, and embankments that might experience steady overflow. Realistic tolerance estimates can be used for both resilient design and risk assessment. A simple framework is developed for estimating tolerable overtopping on grass-covered slopes caused by slowly-varying (in time overtopping discharge (e.g., events like storm surges or river flood waves. The framework adapts the well-known Hewlett curves of tolerable limiting velocity as a function of overflow duration. It has been hypothesized that the form of the Hewlett curves suggests that the grass erosion process is governed by the flow work on the slope above a critical threshold velocity (referred to as excess work, and the tolerable erosional limit is reached when the cumulative excess work exceeds a given value determined from the time-dependent Hewlett curves. The cumulative excess work is expressed in terms of overflow discharge above a critical discharge that slowly varies in time, similar to a discharge hydrograph. The methodology is easily applied using forecast storm surge hydrographs at specific locations where wave action is minimal. For preliminary planning purposes, when storm surge hydrographs are unavailable, hypothetical equations for the water level and overflow discharge hydrographs are proposed in terms of the values at maximum overflow and the total duration of overflow. An example application is given to illustrate use of the methodology.

  18. Magnetic field errors tolerances of Nuclotron booster

    Science.gov (United States)

    Butenko, Andrey; Kazinova, Olha; Kostromin, Sergey; Mikhaylov, Vladimir; Tuzikov, Alexey; Khodzhibagiyan, Hamlet

    2018-04-01

    Generation of magnetic field in units of booster synchrotron for the NICA project is one of the most important conditions for getting the required parameters and qualitative accelerator operation. Research of linear and nonlinear dynamics of ion beam 197Au31+ in the booster have carried out with MADX program. Analytical estimation of magnetic field errors tolerance and numerical computation of dynamic aperture of booster DFO-magnetic lattice are presented. Closed orbit distortion with random errors of magnetic fields and errors in layout of booster units was evaluated.

  19. Radiation therapy tolerance doses for treatment planning

    International Nuclear Information System (INIS)

    Lyman, J.T.

    1987-01-01

    To adequately plan acceptable dose distributions for radiation therapy treatments it is necessary to ensure that normal structures do not receive unacceptable doses. Acceptable doses are generally those that are below a stated tolerance dose for development of some level of complication. To support the work sponsored by the National Cancer Institute, data for the tolerance of normal tissues or organs to low-LET radiation has been compiled from a number of sources. These tolerance dose data are ostensibly for uniform irradiation of all or part of an organ, and are for either 5% (TD 5 ) or 50% (TD 50 ) complication probability. The ''size'' of the irradiated organ is variously stated in terms of the absolute volume or the fraction of the organ volume irradiated, or the area or the length of the treatment field. The accuracy of these data is questionable. Much of the data represent doses that one or several experienced therapists have estimated could be safely given rather than quantitative analyses of clinical observations. Because these data have been obtained from multiple sources with possible different criteria for the definition of a complication, there are sometimes different values for what is apparently the same end point. 20 refs., 1 fig., 1 tab

  20. Tolerance and chimerism.

    Science.gov (United States)

    Kolb, Hans-Jochem; Guenther, Wolfgang; Gyurkocza, Boglarka; Hoetzl, Florian; Simoes, Belinda; Falk, Christine; Schleuning, Michael; Ledderose, Georg

    2003-05-15

    Stem-cell transplantation from human leukocyte antigen (HLA)-haploidentical family members carries a high risk of rejection and graft-versus-host disease (GVHD) if donor and recipient differ by more than one HLA antigen. The authors have developed treatment protocols from studies in dog leukocyte antigen-haploidentical dogs that prevent rejection and modify GVHD to the extent that patients with aggressive hematologic neoplasia can be treated with success. Principal improvements have been achieved in the use of cyclophosphamide and total-body irradiation for conditioning and T-cell depletion for prevention of GVHD. More recently, the combination of marrow and CD6-depleted mobilized donor blood cells (MDBC) has been introduced for HLA-haploidentical transplantation on the basis that CD6-depleted MDBC contain immunoregulatory cells besides stem cells and natural killer cells. Clinical results are reported on 36 patients with high-risk hematologic neoplasia. The results encourage the use of HLA-haploidentical stem-cell transplantation at an earlier stage of the disease. This method could also be of use for tolerance induction in organ transplantation.

  1. Evolution of tolerance by magpies to brood parasitism by great spotted cuckoos.

    Science.gov (United States)

    Soler, J J; Martín-Gálvez, D; Martínez, J G; Soler, M; Canestrari, D; Abad-Gómez, J M; Møller, A P

    2011-07-07

    Hosts may use two different strategies to ameliorate negative effects of a given parasite burden: resistance or tolerance. Although both resistance and tolerance of parasitism should evolve as a consequence of selection pressures owing to parasitism, the study of evolutionary patterns of tolerance has traditionally been neglected by animal biologists. Here, we explore geographical covariation between tolerance of magpies (Pica pica) and brood parasitism by the great spotted cuckoo (Clamator glandarius) in nine different sympatric populations. We estimated tolerance as the slope of the regression of number of magpie fledglings (i.e. host fitness) on number of cuckoo eggs laid in non-depredated nests (which broadly equals parasite burden). We also estimated prevalence of parasitism and level of host resistance (i.e. rejection rates of mimetic model eggs) in these nine populations. In accordance with the hypothetical role of tolerance in the coevolutionary process between magpies and cuckoos we found geographical variation in tolerance estimates that positively covaried with prevalence of parasitism. Levels of resistance and tolerance were not associated, possibly suggesting the lack of a trade-off between the two kinds of defences against great spotted cuckoo parasitism for magpies. We discuss the results in the framework of a mosaic of coevolutionary interactions along the geographical distribution of magpies and great spotted cuckoos for which we found evidence that tolerance plays a major role.

  2. Distribution Line Parameter Estimation Under Consideration of Measurement Tolerances

    DEFF Research Database (Denmark)

    Prostejovsky, Alexander; Gehrke, Oliver; Kosek, Anna Magdalena

    2016-01-01

    conductance that the absolute compensated error is −1.05% and −1.07% for both representations, as opposed to the expected uncompensated error of −79.68%. Identification of a laboratory distribution line using real measurement data grid yields a deviation of 6.75% and 4.00%, respectively, from a calculation...

  3. Tree-growth analyses to estimate tree species' drought tolerance

    NARCIS (Netherlands)

    Eilmann, B.; Rigling, A.

    2012-01-01

    Climate change is challenging forestry management and practices. Among other things, tree species with the ability to cope with more extreme climate conditions have to be identified. However, while environmental factors may severely limit tree growth or even cause tree death, assessing a tree

  4. Mechanical tolerance stackup and analysis

    CERN Document Server

    Fischer, Bryan R

    2011-01-01

    Use Tolerance Analysis Techniques to Avoid Design, Quality, and Manufacturing Problems Before They Happen Often overlooked and misunderstood, tolerance analysis is a critical part of improving products and their design processes. Because all manufactured products are subject to variation, it is crucial that designers predict and understand how these changes can affect form, fit, and function of parts and assemblies--and then communicate their findings effectively. Written by one of the developers of ASME Y14.5 and other geometric dimension and tolerancing (GD&T) standards, Mechanical Tolerance

  5. Advanced cloud fault tolerance system

    Science.gov (United States)

    Sumangali, K.; Benny, Niketa

    2017-11-01

    Cloud computing has become a prevalent on-demand service on the internet to store, manage and process data. A pitfall that accompanies cloud computing is the failures that can be encountered in the cloud. To overcome these failures, we require a fault tolerance mechanism to abstract faults from users. We have proposed a fault tolerant architecture, which is a combination of proactive and reactive fault tolerance. This architecture essentially increases the reliability and the availability of the cloud. In the future, we would like to compare evaluations of our proposed architecture with existing architectures and further improve it.

  6. Tolerable Beam Loss at High-Intensity Machines

    International Nuclear Information System (INIS)

    Krivosheev, Oleg E.; Mokhov, Nikolai V.

    2000-01-01

    Tolerable beam losses are estimated for high-intensity ring accelerators with proton energy of 3 to 16 GeV. Dependence on beam energy, lattice and magnet geometry is studied via full Monte Carlo MARS14 simulations in lattice elements, shielding, tunnel and surrounding dirt with realistic geometry, materials and magnetic fields

  7. Tolerance to and cross tolerance between ethanol and nicotine.

    Science.gov (United States)

    Collins, A C; Burch, J B; de Fiebre, C M; Marks, M J

    1988-02-01

    Female DBA mice were subjected to one of four treatments: ethanol-containing or control diets, nicotine (0.2, 1.0, 5.0 mg/kg/hr) infusion or saline infusion. After removal from the liquid diets or cessation of infusion, the animals were challenged with an acute dose of ethanol or nicotine. Chronic ethanol-fed mice were tolerant to the effects of ethanol on body temperature and open field activity and were cross tolerant to the effects of nicotine on body temperature and heart rate. Nicotine infused animals were tolerant to the effects of nicotine on body temperature and rotarod performance and were cross tolerant to the effects of ethanol on body temperature. Ethanol-induced sleep time was decreased in chronic ethanol- but not chronic nicotine-treated mice. Chronic drug treatment did not alter the elimination rate of either drug. Chronic ethanol treatment did not alter the number or affinity of brain nicotinic receptors whereas chronic nicotine treatment elicited an increase in the number of [3H]-nicotine binding sites. Tolerance and cross tolerance between ethanol and nicotine is discussed in terms of potential effects on desensitization of brain nicotinic receptors.

  8. Accident tolerant fuel analysis

    International Nuclear Information System (INIS)

    2014-01-01

    Safety is central to the design, licensing, operation, and economics of Nuclear Power Plants (NPPs). Consequently, the ability to better characterize and quantify safety margin holds the key to improved decision making about light water reactor design, operation, and plant life extension. A systematic approach to characterization of safety margins and the subsequent margins management options represents a vital input to the licensee and regulatory analysis and decision making that will be involved. The purpose of the Risk Informed Safety Margin Characterization (RISMC) Pathway research and development (R&D) is to support plant decisions for risk-informed margins management by improving economics and reliability, and sustaining safety, of current NPPs. Goals of the RISMC Pathway are twofold: (1) Develop and demonstrate a risk-assessment method coupled to safety margin quantification that can be used by NPP decision makers as part of their margin recovery strategies. (2) Create an advanced ''RISMC toolkit'' that enables more accurate representation of NPP safety margin. In order to carry out the R&D needed for the Pathway, the Idaho National Laboratory is performing a series of case studies that will explore methods- and tools-development issues, in addition to being of current interest in their own right. One such study is a comparative analysis of safety margins of plants using different fuel cladding types: specifically, a comparison between current-technology Zircaloy cladding and a notional ''accident-tolerant'' (e.g., SiC-based) cladding. The present report begins the process of applying capabilities that are still under development to the problem of assessing new fuel designs. The approach and lessons learned from this case study will be included in future Technical Basis Guides produced by the RISMC Pathway. These guides will be the mechanism for developing the specifications for RISMC tools and for defining how plant

  9. TEMPERATURE TOLERANCES AND OSMOREGULATION IN ...

    African Journals Online (AJOL)

    The salinity and temperature tolerances of some burrowiq bivalves which oc:eur ... Along most of the estuary the salinity normally remains close to that of seawater (35'/.) ...... grapsoid crabs, Hemigrapsus nudus and Hemigrapsus oregonensis.

  10. TOLERANCE OF Abelmoschus esculentus (L

    African Journals Online (AJOL)

    Cletus

    Key word: - Tolerance, diesel oil, polluted soil, Abelmoschus esculentus. INTRODUCTION ... errors -of the mean values were calculated for the replicate readings and data .... African Schools and Colleges, 2nd Ed. University Press Limited ...

  11. Antibiotic tolerance and microbial biofilms

    DEFF Research Database (Denmark)

    Folkesson, Anders

    Increased tolerance to antimicrobial agents is thought to be an important feature of microbes growing in biofilms. We study the dynamics of antibiotic action within hydrodynamic flow chamber biofilms of Escherichia coli and Pseudomonas aeruginosa using isogenic mutants and fluorescent gene...... expression reporters and we address the question of how biofilm organization affects antibiotic susceptibility. The dynamics of microbial killing is monitored by viable count determination, and confocal laser microscopy. Our work shows that the apparent increased antibiotic tolerance is due to the formation...... of antibiotic tolerant subpopulations within the biofilm. The formation of these subpopulations is highly variable and dependent on the antibiotic used, the biofilm structural organization and the induction of specific tolerance mechanisms....

  12. Cytokine regulation of immune tolerance

    OpenAIRE

    Wu, Jie; Xie, Aini; Chen, Wenhao

    2014-01-01

    The immune system provides defenses against invading pathogens while maintaining immune tolerance to self-antigens. This immune homeostasis is harmonized by the direct interactions between immune cells and the cytokine environment in which immune cells develop and function. Herein, we discuss three non-redundant paradigms by which cytokines maintain or break immune tolerance. We firstly describe how anti-inflammatory cytokines exert direct inhibitory effects on immune cells to enforce immune ...

  13. Women’s G Tolerance

    Science.gov (United States)

    1986-08-01

    for the groups matched by age (70 pairs), weight sickness, uncomfortable feelings of distension in arms (26 pairs), and act~vity status (84 pairs...mass-spring-damper) s ,stem Straining G tolerance, being dpendent on skeletal having a resonant frequency above about I Hz. As muscular strength and...of the women’s G tolerance stud\\ scclic variations in muscular strength and endurance. was below 0.1 Hz (11), the production of any significant

  14. Fault-tolerant rotary actuator

    Science.gov (United States)

    Tesar, Delbert

    2006-10-17

    A fault-tolerant actuator module, in a single containment shell, containing two actuator subsystems that are either asymmetrically or symmetrically laid out is provided. Fault tolerance in the actuators of the present invention is achieved by the employment of dual sets of equal resources. Dual resources are integrated into single modules, with each having the external appearance and functionality of a single set of resources.

  15. Behavioral Tolerance to Anticholinergic Agents

    Science.gov (United States)

    1986-11-20

    Medicine , 47, 137-141. 7. Kurtz, P.J. (1977) Behavioral and biochemical effects of the carbamate insecticide, mobam. Pharmacology Biochemistry & Behavior...tolerance to marihuana in rats. Pharmacology Biochemistry and Behavior, 1, 73-76. 43 40. Olson, J. and Carder, B. (1974) Behavioral tolerance to... marihuana as a function of amount of prior training. Pharmacology Biochemistry and Behavior, 2, 243-247. 41. Sidman, M. (1960) Tactics of Scientific

  16. Combined methods of tolerance increasing for embedded SRAM

    Science.gov (United States)

    Shchigorev, L. A.; Shagurin, I. I.

    2016-10-01

    The abilities of combined use of different methods of fault tolerance increasing for SRAM such as error detection and correction codes, parity bits, and redundant elements are considered. Area penalties due to using combinations of these methods are investigated. Estimation is made for different configurations of 4K x 128 RAM memory block for 28 nm manufacturing process. Evaluation of the effectiveness of the proposed combinations is also reported. The results of these investigations can be useful for designing fault-tolerant “system on chips”.

  17. Spatial distribution of radionuclides in soil around a coal-fired power plant: lead 210, polonium 210, radium 226, thorium 232, kalium 40 emitted with the fly ash and cesium 137 from the worldwide weapon testing fallout

    Energy Technology Data Exchange (ETDEWEB)

    Bunzl, K.; Hoetzl, H.; Rosner, G.; Winkler, R.

    1984-09-01

    To determine the effect of airborne emissions of radionuclides from coal-fired power plants on the environment, the concentrations of the most important radionuclides were measured in soil samples from the local environments (0.4-5.2 km) as well as in fly ash. The spatial distribution of the radionuclides in the soil did not indicate any significantly increased concentrations in the area downwind of the plant compared to other areas; the ratios lead 210/radium 226 and polonium 210/radium 226 were within the range observed for unaffected soils. The emissions from the plant, though present, are obviously too small to significantly change the natural local distribution pattern of the radionuclides in the soil. A highly significant correlation between potassium 40 and thorium 232 was observed which was independent of the different types of soils found in this area. The concentration of cesium 137 in topsoil, which is the result of worldwide fallout from nuclear weapons testing, varied at some places even within a small distance (approx. 2 km) by up to one order of magnitude. Furthermore, it was observed that the concentration of cesium 137 in soils from cropland was on average a factor of 2 less than in those from grassland. This variability has to be considered in planning monitoring programs around nuclear power plants, which may also release this radionuclide. (A.V.)

  18. 75 FR 29908 - Prothioconazole; Pesticide Tolerances

    Science.gov (United States)

    2010-05-28

    .... The straw numerical value (5 ppm) is matched between the U.S. and Codex. The tolerance definition for... lower (0.07 ppm) than the recommended U.S. group tolerance. The 0.07 ppm value is the current U.S. tolerance value for wheat, but will be replaced by the cereal grain group tolerance. Canada does not...

  19. Quantitative evaluation of the fault tolerance of systems important to the safety of atomic power plants

    International Nuclear Information System (INIS)

    Malkin, S.D.; Sivokon, V.P.; Shmatkova, L.V.

    1989-01-01

    Fault tolerance is the property of a system to preserve its performance upon failures of its components. Thus, in nuclear-reactor technology one has only a qualitative evaluation of fault tolerance - the single-failure criterion, which does not enable one to compare and perform goal-directed design of fault-tolerant systems, and in the field of computer technology there are no generally accepted evaluations of fault tolerance that could be applied effectively to reactor systems. This paper considers alternative evaluations of fault tolerance and a method of comprehensive automated calculation of the reliability and fault tolerance of complex systems. The authors presented quantitative estimates of fault tolerance that develop the single-failure criterion. They have limiting processes that allow simple and graphical standardization. They worked out a method and a program for comprehensive calculation of the reliability and fault tolerance of systems of complex structure that are important to the safety of atomic power plants. The quantitative evaluation of the fault tolerance of these systems exhibits a degree of insensitivity to failures and shows to what extent their reliability is determined by a rigorously defined structure, and to what extent by the probabilistic reliability characteristics of the components. To increase safety, one must increase the fault tolerance of the most important systems of atomic power plants

  20. Tolerance analyses of a quadrupole magnet for advanced photon source upgrade

    International Nuclear Information System (INIS)

    Liu, J.; Jaski, M.; Borland, M.; Jain, A.

    2016-01-01

    Given physics requirements, the mechanical fabrication and assembly tolerances for storage ring magnets can be calculated using analytical methods [1, 2]. However, this method is not easy for complicated magnet designs [1]. In this paper, a novel method is proposed to determine fabrication and assembly tolerances consistent with physics requirements, through a combination of magnetic and mechanical tolerance analyses. In this study, finite element analysis using OPERA is conducted to estimate the effect of fabrication and assembly errors on the magnetic field of a quadrupole magnet and to determine the allowable tolerances to achieve the specified magnetic performances. Based on the study, allowable fabrication and assembly tolerances for the quadrupole assembly are specified for the mechanical design of the quadrupole magnet. Next, to achieve the required assembly level tolerances, mechanical tolerance stackup analyses using a 3D tolerance analysis package are carried out to determine the part and subassembly level fabrication tolerances. This method can be used to determine the tolerances for design of other individual magnets and of magnet strings.

  1. Tolerance analyses of a quadrupole magnet for advanced photon source upgrade

    Energy Technology Data Exchange (ETDEWEB)

    Liu, J., E-mail: Jieliu@aps.anl.gov; Jaski, M., E-mail: jaski@aps.anl.gov; Borland, M., E-mail: borland@aps.anl.gov [Advanced Photon Source, Argonne National Laboratory, 9700 S. Cass Avenue, Lemont, IL60439 (United States); Jain, A., E-mail: jain@bnl.gov [Superconducting Magnet Division, Brookhaven National Laboratory, P.O. Box 5000. Upton, NY 11973-5000 (United States)

    2016-07-27

    Given physics requirements, the mechanical fabrication and assembly tolerances for storage ring magnets can be calculated using analytical methods [1, 2]. However, this method is not easy for complicated magnet designs [1]. In this paper, a novel method is proposed to determine fabrication and assembly tolerances consistent with physics requirements, through a combination of magnetic and mechanical tolerance analyses. In this study, finite element analysis using OPERA is conducted to estimate the effect of fabrication and assembly errors on the magnetic field of a quadrupole magnet and to determine the allowable tolerances to achieve the specified magnetic performances. Based on the study, allowable fabrication and assembly tolerances for the quadrupole assembly are specified for the mechanical design of the quadrupole magnet. Next, to achieve the required assembly level tolerances, mechanical tolerance stackup analyses using a 3D tolerance analysis package are carried out to determine the part and subassembly level fabrication tolerances. This method can be used to determine the tolerances for design of other individual magnets and of magnet strings.

  2. Combining dynamical decoupling with fault-tolerant quantum computation

    International Nuclear Information System (INIS)

    Ng, Hui Khoon; Preskill, John; Lidar, Daniel A.

    2011-01-01

    We study how dynamical decoupling (DD) pulse sequences can improve the reliability of quantum computers. We prove upper bounds on the accuracy of DD-protected quantum gates and derive sufficient conditions for DD-protected gates to outperform unprotected gates. Under suitable conditions, fault-tolerant quantum circuits constructed from DD-protected gates can tolerate stronger noise and have a lower overhead cost than fault-tolerant circuits constructed from unprotected gates. Our accuracy estimates depend on the dynamics of the bath that couples to the quantum computer and can be expressed either in terms of the operator norm of the bath's Hamiltonian or in terms of the power spectrum of bath correlations; we explain in particular how the performance of recursively generated concatenated pulse sequences can be analyzed from either viewpoint. Our results apply to Hamiltonian noise models with limited spatial correlations.

  3. B cells in operational tolerance.

    Science.gov (United States)

    Chesneau, M; Danger, R; Soulillou, J-P; Brouard, S

    2018-02-16

    Transplantation is currently the therapy of choice for endstage organ failure even though it requires long-term immunosuppresive therapy, with its numerous side effects, for acceptance of the transplanted organ. In rare cases however, patients develop operational tolerance, that is, graft survival without immunosuppression. Studies conducted on these patients reveal genetic, phenotypic, and functional signatures. They provide a better understanding of the immunological mechanisms involved in operational tolerance and define biomarkers that could be used to adapt immunosuppressive treatment to the individual, safely reduce immunosuppression doses, and ideally and safely guide immunosuppression withdrawal. This review summarizes studies that suggest a role for B cells as biomarkers of operational tolerance and discusses the use of B cells as a predictive tool for immunologic risk. Copyright © 2018. Published by Elsevier Inc.

  4. Immune tolerance in radiation chimeras

    International Nuclear Information System (INIS)

    Awaya, Kazuhiko; Kuniki, Hiromichi; Neki, Miyuki

    1978-01-01

    Establishment of immune tolerance in radiation chimeras and the mechanism of maintaining it were discussed from certain points. Semiallogeneic radiation chimeras are mostly of long-living, and the hematopoietic organ of this individual consists mainly of the cells derived from the marrow donor, i. e., F 1 -type cells. F 1 -type lymphocytes can distinguish parental strain cells from themselves. In these chimeras, a F 1 -skin graft maintains to be fresh as long as the host is alive, showing immune tolerance effective through its life. In establishment and maintenance of this immune tolerance, the suppressing mechanism of host-type or F 1 -type seems to be involved. The allogeneic radiation chimera has very poor long-survival rate compared with that of the semiallogeneic radiation chimera. To raise this survival rate, efforts are now being made from the immunological point of view. (Ueda, J.)

  5. Methods to establish flaw tolerances

    International Nuclear Information System (INIS)

    Varga, T.

    1978-01-01

    Three conventional methods used to establish flaw tolerances are compared with new approaches using fracture mechanics. The conventional methods are those based on (a) non-destructive testing methods; (b) fabrication and quality assurance experience; and (c) service and damage experience. Pre-requisites of fracture mechanics methods are outlined, and summaries given of linear elastic mechanics (LEFM) and elastoplastic fracture mechanics (EPFM). The latter includes discussion of C.O.D.(crack opening displacement), the J-integral and equivalent energy. Proposals are made for establishing flaw tolerances. (U.K.)

  6. Tolerating extremism : to what extent should intolerance be tolerated?

    NARCIS (Netherlands)

    Guiora, Amos Neuser

    2013-01-01

    In discussing extremism, the key questions are: to whom is a duty owed and what are the limits of intolerance that are to be tolerated? Answering these questions requires examining limits and rights; analyzing them in the context of extremism is the ‘core’ of this book. While freedom of speech and

  7. Parameter Estimation

    DEFF Research Database (Denmark)

    Sales-Cruz, Mauricio; Heitzig, Martina; Cameron, Ian

    2011-01-01

    of optimisation techniques coupled with dynamic solution of the underlying model. Linear and nonlinear approaches to parameter estimation are investigated. There is also the application of maximum likelihood principles in the estimation of parameters, as well as the use of orthogonal collocation to generate a set......In this chapter the importance of parameter estimation in model development is illustrated through various applications related to reaction systems. In particular, rate constants in a reaction system are obtained through parameter estimation methods. These approaches often require the application...... of algebraic equations as the basis for parameter estimation.These approaches are illustrated using estimations of kinetic constants from reaction system models....

  8. Tolerance of snakes to hypergravity

    Science.gov (United States)

    Lillywhite, H. B.; Ballard, R. E.; Hargens, A. R.

    1996-01-01

    Sensitivity of carotid blood flow to increased gravitational force acting in the head-to-tail direction(+Gz) was studied in diverse species of snakes hypothesized to show adaptive variation of response. Tolerance to increased gravity was measured red as the maximum graded acceleration force at which carotid blood flow ceased and was shown to vary according to gravitational adaptation of species defined by their ecology and behavior. Multiple regression analysis showed that gravitational habitat, but not body length, had a significant effect on Gz tolerance. At the extremes, carotid blood flow decreased in response to increasing G force and approached zero near +1 Gz in aquatic and ground-dwelling species, whereas in climbing species carotid flow was maintained at forces in excess of +2 Gz. Tolerant (arboreal) species were able to withstand hypergravic forces of +2 to +3 Gz for periods up to 1 h without cessation of carotid blood flow or loss of body movement and tongue flicking. Data suggest that the relatively tight skin characteristic of tolerant species provides a natural antigravity suit and is of prime importance in counteracting Gz stress on blood circulation.

  9. Assessing Your Board's Risk Tolerance

    Science.gov (United States)

    Griswold, John S.; Jarvis, William F.

    2014-01-01

    In the wake of the financial crisis, trustees of many endowed nonprofit institutions realized that their portfolio was riskier than they thought and their own ability to tolerate loss wasn't as strong as they imagined. What can board and investment committee members do to improve their ability to assess their--and their institution's--capacity for…

  10. Toleration, Multiculturalism and Mistaken Belief

    Science.gov (United States)

    Standish, Paul

    2006-01-01

    Doubts have been expressed about the virtue of toleration, especially in view of what some have seen as its complicity with a morality of anything goes. More rigorous arguments have been provided by Peter Gardner and Harvey Siegel against the relativism evident in certain versions of multiculturalism and in the new religious studies. This article…

  11. Genetic basis of variation for salinity tolerance in okra (abelmoschus esculentus L.)

    International Nuclear Information System (INIS)

    Ikram-ul-Haq; Khan, A.A.; Azhar, F.M.; Ullah, E.

    2010-01-01

    The development of salt tolerant plants through selection and breeding depends on the presence of the genetic variability within the crop species in response to salt stress, which must have significant genetic component. Such information is not extensively available in vegetable crops. The present study was carried out to gain some information on the genetic basis of variation for salinity tolerance in okra. North Carolina Mating Design II (NCM II) was used for the estimation of genetic components of variation in the traits affecting salinity tolerance. The inheritance of the traits affecting salinity tolerance at the seedling stage appeared to be controlled by both additive and non-additive effects (dominance and epistasis). The narrow sense heritability estimates ranged from 40 to 65% and 7 to 70% and the estimates of broad sense heritability ranged from 65 to 99% and 20 to 99% for absolute and relative values. The additive effects were relatively more prominent and narrow sense heritability was moderate. The high additive component for absolute Na/sup +/ and K/sup +//Na/sup +/ ratio at 60 and 80 mM NaCl, relative Na+ at 80 mM NaCl suggested that improvement for salinity tolerance in okra would be possible on the basis of these characteristics through selection and breeding. The genetic variation for tolerance to NaCl salinity existed among the okra genotypes, which had considerable heritable component and, therefore, genetic improvement of okra genotypes for salinity tolerance through recurrent selection method is possible. (author)

  12. Water-sediment distribution and behaviour of Polonium ("2"1"0Po) in a shallow coastal area with high concentration of dissolved organic matters in water, North Vietnam

    International Nuclear Information System (INIS)

    Tran Thi Van; Nguyen Duc Tam; Dang Duc Nhan; Nguyen Quang Long; Duong Van Thang; Bui Duy Cam

    2016-01-01

    The behaviour and water-sediment distribution of particle-reactive Polonium-210 in the marine environment with high concentration of total suspended particulates (TSP) and dissolved organic matters (DOC) along the coast of the Tonkin Gulf (North Vietnam) were investigated. It was revealed that the water-sediment distribution coefficient, K_d(s), of "2"1"0Po varied from 2.39x10"3 to 1.9x10"4 (L kg"-"1) and from 7x10"3 to 2.5x10"5 (L kg"-"1), respectively, in the rainy and dry season. This implies that in the aquatic environment "2"1"0Po tends to be of high affinity to suspended particulates. The "2"1"0Po K_d(s) was positively correlated with salinity in both rainy and dry seasons. With DOC the K_d(s) was positively correlated in the rainy season, but in the dry season the relationship tended to be reverse. This behaviour of "2"1"0Po in the coastal region was explained by the variation of pH of seawater and by the complexation of the isotope with DOC. The K_d(s) found in this study was in an order lower compared to that reported by Malaysian researchers for the Thailand Gulf. The most important source of "2"1"0Po was suggested to be from in-situ generation by the decay of its grand-parent "2"1"0Pb which mainly derived from the atmospheric fall-out. (author)

  13. Physiological determinants of human acute hypoxia tolerance.

    Science.gov (United States)

    2013-11-01

    AbstractIntroduction. We investigated possible physiological determinants of variability in hypoxia tolerance in subjects given a 5-minute normobaric exposure to 25,000 ft equivalent. Physiological tolerance to hypoxia was defined as the magnitude of...

  14. Persistence and drug tolerance in pathogenic yeast

    DEFF Research Database (Denmark)

    Bojsen, Rasmus Kenneth; Regenberg, Birgitte; Folkesson, Sven Anders

    2017-01-01

    In this review, we briefly summarize the current understanding of how fungal pathogens can persist antifungal treatment without heritable resistance mutations by forming tolerant persister cells. Fungal infections tolerant to antifungal treatment have become a major medical problem. One mechanism...

  15. Drought and submergence tolerance in plants

    Energy Technology Data Exchange (ETDEWEB)

    Du, Hewei; Zhou, Yufan; Oksenberg, Nir; Ronald, Pamela

    2017-11-14

    The invention provides methods of genetically modified plants to increase tolerance to drought and/or submergence. The invention additionally provides plants having increased drought and/or submergence tolerance engineered using such methods.

  16. Urbanism, Migration, and Tolerance: A Reassessment.

    Science.gov (United States)

    Wilson, Thomas C.

    1991-01-01

    Urbanism's impact on the personality may be stronger than previously thought. Finds that urban residence has a strong positive effect on tolerance. Migration also promotes tolerance, regardless of the size of the destination community. (DM)

  17. Fault tolerant control for steam generators in nuclear power plant

    International Nuclear Information System (INIS)

    Deng Zhihong; Shi Xiaocheng; Xia Guoqing; Fu Mingyu

    2010-01-01

    Based on the nonlinear system with stochastic noise, a bank of extended Kalman filters is used to estimate the state of sensors. It can real-time detect and isolate the single sensor fault, and reconstruct the sensor output to keep steam generator water level stable. The simulation results show that the methodology of employing a bank of extended Kalman filters for steam generator fault tolerant control design is feasible. (authors)

  18. Estimation of 210Po activity in mussel sample and its contribution in radiation dose to the public around Kanyakumari Coast, India

    International Nuclear Information System (INIS)

    Macklin Rani, L.; Govindaraju, M.; Jeevanram, R.K.; Muthukumaran, V.R.

    2013-01-01

    Polonium-210 ( 210 Po), a naturally occurring á-emitting radionuclide exists in the environment as a result of Uranium- 238 ( 238 U) decay chain. It is therefore ubiquitously distributed in the rocks, soils, making up Earths crust, in the atmosphere and in natural waters. 210 Po enters in marine organisms via adsorption, absorption and ingestion and is transferred through seafood consumption. The concentration of 210 Po in the edible portions of marine organisms may be many folds higher than that in the seawater because of biological re-concentration processes. In the present study, sampling sites were chosen to determine the difference of 210 Po concentration in bivalve mussel, an appropriate bio-indicator for radioactive contamination. The concentration of radionuclide Polonium-210 ( 210 Po) in brown mussel (Perna perna), obtained from different locations of Kanyakumari coastal area were estimated, which ranged between 76.0 ± 5.1 Bq/kg and 310.20 ± 18.4 Bq/kg. The highest activity was observed at Kalluvilai. The daily and annual intake of 210 Po from ingestion via mussel was estimated in these areas. To evaluate the internal exposure, annual committed effective dose to the adult population of this coastal area was determined and compared with the Indian and worldwide values to assess the risk status of the study area. It was observed that the average annual committed effective dose of 210 Po through ingestion is higher than the recommended dose of ICRP, 1990 (1 mSv/year) for general public due to the contribution of seafood, mussel species (3.09 mSv/year) in daily diet. (author)

  19. 75 FR 17566 - Flutolanil; Pesticide Tolerances

    Science.gov (United States)

    2010-04-07

    ... ppm, and the greater tolerance value is needed to accommodate indirect residues from soybean..., and soybean hay at 2.5 ppm are being revoked since the same tolerance values are being established...; Pesticide Tolerances AGENCY: Environmental Protection Agency (EPA). ACTION: Final rule. SUMMARY: This...

  20. 77 FR 49732 - Cyprodinil; Pesticide Tolerances

    Science.gov (United States)

    2012-08-17

    .../puree (1x) and lemon/lime juice (1x) were used to modify the tolerance values. iii. Cancer. Based on the... the tolerance necessitate a higher value. Additionally, Codex has an established MRL on grape at 3 ppm...; Pesticide Tolerances AGENCY: Environmental Protection Agency (EPA). ACTION: Final rule. SUMMARY: This...

  1. 15 CFR 750.11 - Shipping tolerances.

    Science.gov (United States)

    2010-01-01

    ... in the ECCN applicable to your item reads “ $ value” or “in $ value”, there is no shipping tolerance... is no shipping tolerance with respect to the number of units. However, the value of all of your... shipping tolerance on this license because the items are controlled by an ECCN where “$ value” is the...

  2. 78 FR 18511 - Thiamethoxam; Pesticide Tolerances

    Science.gov (United States)

    2013-03-27

    ... Health Risk Assessment of New Uses on Strawberry, Pistachio, and Citrus; New Tolerance for Tea; and... Uses on Strawberry, Pistachio, and Citrus; New Tolerance for Tea; and Revised PHI and Tolerance for... ``Clothianidin--Aggregate Human Health Risk Assessment of New Uses on Strawberry, Pistachio, and Citrus; New...

  3. 77 FR 28493 - Propylene Oxide; Tolerance Actions

    Science.gov (United States)

    2012-05-15

    .... SUMMARY: EPA is establishing the tree nut crop group tolerance and separate tolerances on pistachio and...; nut, tree, group 14; and pistachio; and in 40 CFR 180.491(a)(2) tolerances for propylene chlorohydrin at 10.0 ppm on nut, pine; nut, tree, group 14; and pistachio. Also, in accordance with current Agency...

  4. 75 FR 26673 - Clethodim; Pesticide Tolerances

    Science.gov (United States)

    2010-05-12

    ... regulation establishes tolerances for residues of clethodim in or on the raw agricultural commodity artichoke... clethodim, in or on the raw agricultural commodity artichoke, globe at 1.3 parts per million (ppm... bushberry subgroup 13-07B tolerance from 3.0 ppm to 0.20 ppm and the globe artichoke tolerance from 1.3 ppm...

  5. Selection and characterisation of high ethanol tolerant ...

    African Journals Online (AJOL)

    15% ethanol tolerance. High level ethanol tolerant Saccharomyces yeast, Orc 6, was investigated for its potential application in ethanologenic fermentations. Data presented in this study revealed that Orc 6 yeast isolate tolerated osmotic stress above 12% (w/v) sorbitol and 15% (w/v) sucrose equivalent of osmotic pressure ...

  6. Zero Tolerance: Advantages and Disadvantages. Research Brief

    Science.gov (United States)

    Walker, Karen

    2009-01-01

    What are the positives and negatives of zero tolerance? What should be considered when examining a school's program? Although there are no definitive definitions of zero tolerance, two commonly used ones are as follows: "Zero tolerance means that a school will automatically and severely punish a student for a variety of infractions" (American Bar…

  7. What is Fault Tolerant Control

    DEFF Research Database (Denmark)

    Blanke, Mogens; Frei, C. W.; Kraus, K.

    2000-01-01

    Faults in automated processes will often cause undesired reactions and shut-down of a controlled plant, and the consequences could be damage to the plant, to personnel or the environment. Fault-tolerant control is the synonym for a set of recent techniques that were developed to increase plant...... availability and reduce the risk of safety hazards. Its aim is to prevent that simple faults develop into serious failure. Fault-tolerant control merges several disciplines to achieve this goal, including on-line fault diagnosis, automatic condition assessment and calculation of remedial actions when a fault...... is detected. The envelope of the possible remedial actions is wide. This paper introduces tools to analyze and explore structure and other fundamental properties of an automated system such that any redundancy in the process can be fully utilized to enhance safety and a availability....

  8. Human tolerance to space flight

    Science.gov (United States)

    Huntoon, C. L.

    1989-01-01

    Medical studies of astronauts and cosmonauts before, during, and after space missions have identified several effects of weightlessness and other factors that influence the ability of humans to tolerate space flight. Weightlessness effects include space motion sickness, cardiovascular abnormalities, reduction in immune system function, loss of red blood cells, loss of bone mass, and muscle atrophy. Extravehicular activity (EVA) increases the likelihood that decompression sickness may occur. Radiation also gives reason for concern about health of crewmembers, and psychological factors are important on long-term flights. Countermeasures that have been used include sensory preadaptation, prebreathing and use of various air mixtures for EVA, loading with water and electrolytes, exercise, use of pharmacological agents and special diets, and psychological support. It appears that humans can tolerate and recover satisfactorily from at least one year of space flight, but a number of conditions must be further ameliorated before long-duration missions can be considered routine.

  9. Fault Tolerant External Memory Algorithms

    DEFF Research Database (Denmark)

    Jørgensen, Allan Grønlund; Brodal, Gerth Stølting; Mølhave, Thomas

    2009-01-01

    Algorithms dealing with massive data sets are usually designed for I/O-efficiency, often captured by the I/O model by Aggarwal and Vitter. Another aspect of dealing with massive data is how to deal with memory faults, e.g. captured by the adversary based faulty memory RAM by Finocchi and Italiano....... However, current fault tolerant algorithms do not scale beyond the internal memory. In this paper we investigate for the first time the connection between I/O-efficiency in the I/O model and fault tolerance in the faulty memory RAM, and we assume that both memory and disk are unreliable. We show a lower...... bound on the number of I/Os required for any deterministic dictionary that is resilient to memory faults. We design a static and a dynamic deterministic dictionary with optimal query performance as well as an optimal sorting algorithm and an optimal priority queue. Finally, we consider scenarios where...

  10. Copper tolerance of Trichoderma species

    Directory of Open Access Journals (Sweden)

    Jovičić-Petrović Jelena

    2014-01-01

    Full Text Available Some Trichoderma strains can persist in ecosystems with high concentrations of heavy metals. The aim of this research was to examine the variability of Trichoderma strains isolated from different ecosystems, based on their morphological properties and restriction analysis of ITS fragments. The fungal growth was tested on potato dextrose agar, amended with Cu(II concentrations ranging from 0.25 to 10 mmol/l, in order to identify copper-resistant strains. The results indicate that some isolated strains of Trichoderma sp. show tolerance to higher copper concentrations. Further research to examine the ability of copper bioaccumulation by tolerant Trichoderma strains is needed. [Projekat Ministarstva nauke Republike Srbije, br. TR 31080 i br. III 43010

  11. A damage-tolerant glass.

    Science.gov (United States)

    Demetriou, Marios D; Launey, Maximilien E; Garrett, Glenn; Schramm, Joseph P; Hofmann, Douglas C; Johnson, William L; Ritchie, Robert O

    2011-02-01

    Owing to a lack of microstructure, glassy materials are inherently strong but brittle, and often demonstrate extreme sensitivity to flaws. Accordingly, their macroscopic failure is often not initiated by plastic yielding, and almost always terminated by brittle fracture. Unlike conventional brittle glasses, metallic glasses are generally capable of limited plastic yielding by shear-band sliding in the presence of a flaw, and thus exhibit toughness-strength relationships that lie between those of brittle ceramics and marginally tough metals. Here, a bulk glassy palladium alloy is introduced, demonstrating an unusual capacity for shielding an opening crack accommodated by an extensive shear-band sliding process, which promotes a fracture toughness comparable to those of the toughest materials known. This result demonstrates that the combination of toughness and strength (that is, damage tolerance) accessible to amorphous materials extends beyond the benchmark ranges established by the toughest and strongest materials known, thereby pushing the envelope of damage tolerance accessible to a structural metal.

  12. Modelling Accident Tolerant Fuel Concepts

    Energy Technology Data Exchange (ETDEWEB)

    Hales, Jason Dean [Idaho National Laboratory; Gamble, Kyle Allan Lawrence [Idaho National Laboratory

    2016-05-01

    The catastrophic events that occurred at the Fukushima-Daiichi nuclear power plant in 2011 have led to widespread interest in research of alternative fuels and claddings that are proposed to be accident tolerant. The United States Department of Energy (DOE) through its Nuclear Energy Advanced Modeling and Simulation (NEAMS) program has funded an Accident Tolerant Fuel (ATF) High Impact Problem (HIP). The ATF HIP is a three-year project to perform research on two accident tolerant concepts. The final outcome of the ATF HIP will be an in-depth report to the DOE Advanced Fuels Campaign (AFC) giving a recommendation on whether either of the two concepts should be included in their lead test assembly scheduled for placement into a commercial reactor in 2022. The two ATF concepts under investigation in the HIP are uranium silicide fuel and iron-chromium-aluminum (FeCrAl) alloy cladding. Utilizing the expertise of three national laboratory participants (Idaho National Laboratory, Los Alamos National Laboratory, and Argonne National Laboratory), a comprehensive multiscale approach to modeling is being used that includes atomistic modeling, molecular dynamics, rate theory, phase-field, and fuel performance simulations. Model development and fuel performance analysis are critical since a full suite of experimental studies will not be complete before AFC must prioritize concepts for focused development. In this paper, we present simulations of the two proposed accident tolerance fuel systems: U3Si2 fuel with Zircaloy-4 cladding, and UO2 fuel with FeCrAl cladding. Sensitivity analyses are completed using Sandia National Laboratories’ Dakota software to determine which input parameters (e.g., fuel specific heat) have the greatest influence on the output metrics of interest (e.g., fuel centerline temperature). We also outline the multiscale modelling approach being employed. Considerable additional work is required prior to preparing the recommendation report for the Advanced

  13. Historical overview of immunological tolerance.

    Science.gov (United States)

    Schwartz, Ronald H

    2012-04-01

    A fundamental property of the immune system is its ability to mediate self-defense with a minimal amount of collateral damage to the host. The system uses several different mechanisms to achieve this goal, which is collectively referred to as the "process of immunological tolerance." This article provides an introductory historical overview to these various mechanisms, which are discussed in greater detail throughout this collection, and then briefly describes what happens when this process fails, a state referred to as "autoimmunity."

  14. SALT TOLERANCE OF CROP PLANTS

    OpenAIRE

    Hamdia, M. A; Shaddad, M. A. K.

    2010-01-01

    Several environmental factors adversely affect plant growth and development and final yield performance of a crop. Drought, salinity, nutrient imbalances (including mineral toxicities and deficiencies) and extremes of temperature are among the major environmental constraints to crop productivity worldwide. Development of crop plants with stress tolerance, however, requires, among others, knowledge of the physiological mechanisms and genetic controls of the contributing traits at different pla...

  15. Fault Tolerant Wind Farm Control

    DEFF Research Database (Denmark)

    Odgaard, Peter Fogh; Stoustrup, Jakob

    2013-01-01

    In the recent years the wind turbine industry has focused on optimizing the cost of energy. One of the important factors in this is to increase reliability of the wind turbines. Advanced fault detection, isolation and accommodation are important tools in this process. Clearly most faults are deal...... scenarios. This benchmark model is used in an international competition dealing with Wind Farm fault detection and isolation and fault tolerant control....

  16. SALT TOLERANCE OF CROP PLANTS

    Directory of Open Access Journals (Sweden)

    Hamdia, M. A

    2010-09-01

    Full Text Available Several environmental factors adversely affect plant growth and development and final yield performance of a crop. Drought, salinity, nutrient imbalances (including mineral toxicities and deficiencies and extremes of temperature are among the major environmental constraints to crop productivity worldwide. Development of crop plants with stress tolerance, however, requires, among others, knowledge of the physiological mechanisms and genetic controls of the contributing traits at different plant developmental stages. In the past 2 decades, biotechnology research has provided considerable insights into the mechanism of biotic stress tolerance in plants at the molecular level. Furthermore, different abiotic stress factors may provoke osmotic stress, oxidative stress and protein denaturation in plants, which lead to similar cellular adaptive responses such as accumulation of compatible solutes, induction of stress proteins, and acceleration of reactive oxygen species scavenging systems. Recently, the authores try to improve plant tolerance to salinity injury through either chemical treatments (plant hormones, minerals, amino acids, quaternary ammonium compounds, polyamines and vitamins or biofertilizers treatments (Asymbiotic nitrogen-fixing bacteria, symbiotic nitrogen-fixing bacteria and mycorrhiza or enhanced a process used naturally by plants to minimise the movement of Na+ to the shoot, using genetic modification to amplify the process, helping plants to do what they already do - but to do it much better."

  17. Tolerance of Snakes to Hypergravity

    Science.gov (United States)

    Lillywhite, H. B.; Ballard, R. E.; Hargens, A. R.

    1994-01-01

    Sensitivity of carotid blood flow to +Gz (head-to-tail) acceleration was studied in six species of snakes hypothesized to show varied adaptive cardiovascular responses to gravity. Blood flow in the proximal carotid artery was measured in 15 snakes before, during and following stepwise increments of +0.25Gz force produced on a 2.4 m diameter centrifuge. During centrifugation each snake was confined to a straight position within an individually- fitted acrylic tube with the head facing the center of rotation. We measured the centrifugal force at the tail of the snake in order to quantify the maximum intensity of force gradient promoting antero-posterior pooling of blood. Tolerance to increased gravity was quantified as the acceleration force at which carotid blood flow ceased. This parameter varied according to the gravitational adaptation of species defined by their ecology and behavior. At the extremes, carotid blood flow decreased in response to increasing gravity and approached zero near +1Gz in aquatic and ground-dwelling species, whereas in climbing species carotid flow was maintained at forces in excess of +2Gz. Surprisingly, tolerant (arboreal) species withstood hypergravic forces of +2 to +3 G. for periods up to 1 h without cessation of carotid blood flow or apparent loss of consciousness. Data suggest that relatively tight skin of the tolerant species provides a natural antigravity suit which is of prime importance in counteracting Gz stress on blood circulation.

  18. Fault-tolerant architecture: Evaluation methodology

    International Nuclear Information System (INIS)

    Battle, R.E.; Kisner, R.A.

    1992-08-01

    The design and reliability of four fault-tolerant architectures that may be used in nuclear power plant control systems were evaluated. Two architectures are variations of triple-modular-redundant (TMR) systems, and two are variations of dual redundant systems. The evaluation includes a review of methods of implementing fault-tolerant control, the importance of automatic recovery from failures, methods of self-testing diagnostics, block diagrams of typical fault-tolerant controllers, review of fault-tolerant controllers operating in nuclear power plants, and fault tree reliability analyses of fault-tolerant systems

  19. IRON-TOLERANT CYANOBACTERIA: IMPLICATIONS FOR ASTROBIOLOGY

    Science.gov (United States)

    Brown, Igor I.; Allen, Carlton C.; Mummey, Daniel L.; Sarkisova, Svetlana A.; McKay, David S.

    2006-01-01

    The review is dedicated to the new group of extremophiles - iron tolerant cyanobacteria. The authors have analyzed earlier published articles about the ecology of iron tolerant cyanobacteria and their diversity. It was concluded that contemporary iron depositing hot springs might be considered as relative analogs of Precambrian environment. The authors have concluded that the diversity of iron-tolerant cyanobacteria is understudied. The authors also analyzed published data about the physiological peculiarities of iron tolerant cyanobacteria. They made the conclusion that iron tolerant cyanobacteria may oxidize reduced iron through the photosystem of cyanobacteria. The involvement of both Reaction Centers 1 and 2 is also discussed. The conclusion that iron tolerant protocyanobacteria could be involved in banded iron formations generation is also proposed. The possible mechanism of the transition from an oxygenic photosynthesis to an oxygenic one is also discussed. In the final part of the review the authors consider the possible implications of iron tolerant cyanobacteria for astrobiology.

  20. Effect of model choice and sample size on statistical tolerance limits

    International Nuclear Information System (INIS)

    Duran, B.S.; Campbell, K.

    1980-03-01

    Statistical tolerance limits are estimates of large (or small) quantiles of a distribution, quantities which are very sensitive to the shape of the tail of the distribution. The exact nature of this tail behavior cannot be ascertained brom small samples, so statistical tolerance limits are frequently computed using a statistical model chosen on the basis of theoretical considerations or prior experience with similar populations. This report illustrates the effects of such choices on the computations

  1. Natural selection on individual variation in tolerance of gastrointestinal nematode infection.

    Directory of Open Access Journals (Sweden)

    Adam D Hayward

    2014-07-01

    Full Text Available Hosts may mitigate the impact of parasites by two broad strategies: resistance, which limits parasite burden, and tolerance, which limits the fitness or health cost of increasing parasite burden. The degree and causes of variation in both resistance and tolerance are expected to influence host-parasite evolutionary and epidemiological dynamics and inform disease management, yet very little empirical work has addressed tolerance in wild vertebrates. Here, we applied random regression models to longitudinal data from an unmanaged population of Soay sheep to estimate individual tolerance, defined as the rate of decline in body weight with increasing burden of highly prevalent gastrointestinal nematode parasites. On average, individuals lost weight as parasite burden increased, but whereas some lost weight slowly as burden increased (exhibiting high tolerance, other individuals lost weight significantly more rapidly (exhibiting low tolerance. We then investigated associations between tolerance and fitness using selection gradients that accounted for selection on correlated traits, including body weight. We found evidence for positive phenotypic selection on tolerance: on average, individuals who lost weight more slowly with increasing parasite burden had higher lifetime breeding success. This variation did not have an additive genetic basis. These results reveal that selection on tolerance operates under natural conditions. They also support theoretical predictions for the erosion of additive genetic variance of traits under strong directional selection and fixation of genes conferring tolerance. Our findings provide the first evidence of selection on individual tolerance of infection in animals and suggest practical applications in animal and human disease management in the face of highly prevalent parasites.

  2. Morphological characteristic of purple long yard bean cultivars and their tolerance to drought stress

    Directory of Open Access Journals (Sweden)

    M W Lestari

    2015-01-01

    Full Text Available The cultivation of purple long yard bean which tolerance to drought stress and have high productivity can improve farming in arid area. The purpose of this study was to evaluate the mechanism of the tolerance purple long yard beans to drought stress based on morphologic characters, to get the hypothesis method of tolerance and to obtain tolerance cultivars to the drought stress. Eight cultivars of purple long yard beans, i.e. UBPHU1-41, UBPHU1-130, UBPU3-153, UBPU1-202, UBPU2-222, UBPU1-365, Brawijaya 4 and Bagong 2, were tested in two environmental conditions, 100% field capacity and 50% field capacity. The results showed that drought stress in purple long yard bean affected all morphological characters observed, except for root length and flowering time. Estimation of tolerance to drought stress using the Principles Component Analysis (PCA showed that the shoot fresh weight could be an indicator of purple pod bean tolerance to drought stress. However, the test using Stress Susceptibility Index (SSI was not able to classify the purple long yard bean tolerance to drought stress. The results of analysis using PCA followed by discriminant analysis and clustering dendrogram showed that the UBPU1-41, UBPU1-130, UBPU2-222, UBPU1-365, UB4 and Bagong 2 cultivars were medium cultivars that are tolerant to drought stress. Therefore, they can be planted in semiarid regions.

  3. Evaluation of digital fault-tolerant architectures for nuclear power plant control systems

    International Nuclear Information System (INIS)

    Battle, R.E.

    1990-01-01

    Four fault tolerant architectures were evaluated for their potential reliability in service as control systems of nuclear power plants. The reliability analyses showed that human- and software-related common cause failures and single points of failure in the output modules are dominant contributors to system unreliability. The four architectures are triple-modular-redundant (TMR), both synchronous and asynchronous, and also dual synchronous and asynchronous. The evaluation includes a review of design features, an analysis of the importance of coverage, and reliability analyses of fault tolerant systems. An advantage of fault-tolerant controllers over those not fault tolerant, is that fault-tolerant controllers continue to function after the occurrence of most single hardware faults. However, most fault-tolerant controllers have single hardware components that will cause system failure, almost all controllers have single points of failure in software, and all are subject to common cause failures. Reliability analyses based on data from several industries that have fault-tolerant controllers were used to estimate the mean-time-between-failures of fault-tolerant controllers and to predict those failures modes that may be important in nuclear power plants. 7 refs., 4 tabs

  4. The failure-tolerant leader.

    Science.gov (United States)

    Farson, Richard; Keyes, Ralph

    2002-08-01

    "The fastest way to succeed," IBM's Thomas Watson, Sr., once said, "is to double your failure rate." In recent years, more and more executives have embraced Watson's point of view, coming to understand what innovators have always known: Failure is a prerequisite to invention. But while companies may grasp the value of making mistakes at the level of corporate practices, they have a harder time accepting the idea at the personal level. People are afraid to fail, and corporate culture reinforces that fear. In this article, psychologist and former Harvard Business School professor Richard Farson and coauthor Ralph Keyes discuss how companies can reduce the fear of miscues. What's crucial is the presence of failure-tolerant leaders--executives who, through their words and actions, help employees overcome their anxieties about making mistakes and, in the process, create a culture of intelligent risk-taking that leads to sustained innovation. Such leaders don't just accept productive failure, they promote it. Drawing from their research in business, politics, sports, and science, the authors identify common practices among failure-tolerant leaders. These leaders break down the social and bureaucratic barriers that separate them from their followers. They engage at a personal level with the people they lead. They avoid giving either praise or criticism, preferring to take a nonjudgmental, analytical posture as they interact with staff. They openly admit their own mistakes rather than trying to cover them up or shifting the blame. And they try to root out the destructive competitiveness built into most organizations. Above all else, failure-tolerant leaders push people to see beyond traditional definitions of success and failure. They know that as long as a person views failure as the opposite of success, rather than its complement, he or she will never be able to take the risks necessary for innovation.

  5. Noise tolerant spatiotemporal chaos computing.

    Science.gov (United States)

    Kia, Behnam; Kia, Sarvenaz; Lindner, John F; Sinha, Sudeshna; Ditto, William L

    2014-12-01

    We introduce and design a noise tolerant chaos computing system based on a coupled map lattice (CML) and the noise reduction capabilities inherent in coupled dynamical systems. The resulting spatiotemporal chaos computing system is more robust to noise than a single map chaos computing system. In this CML based approach to computing, under the coupled dynamics, the local noise from different nodes of the lattice diffuses across the lattice, and it attenuates each other's effects, resulting in a system with less noise content and a more robust chaos computing architecture.

  6. Anhydrobiosis and Freezing-Tolerance

    DEFF Research Database (Denmark)

    McGill, Lorraine; Shannon, Adam; Pisani, Davide

    2015-01-01

    Anhydrobiotic animals can survive the loss of both free and bound water from their cells. While in this state they are also resistant to freezing. This physiology adapts anhydrobiotes to harsh environments and it aids their dispersal. Panagrolaimus davidi, a bacterial feeding anhydrobiotic nematode...... Panagrolaimus strains from tropical, temperate, continental and polar habitats and we analysed their phylogenetic relationships. We found that several other Panagrolaimus isolates can also survive freezing when fully hydrated and that tissue extracts from these freezing-tolerant nematodes can inhibit the growth...

  7. Radiation tolerance of amorphous semiconductors

    International Nuclear Information System (INIS)

    Nicolaides, R.V.; DeFeo, S.; Doremus, L.W.

    1976-01-01

    In an attempt to determine the threshold radiation damage in amorphous semiconductors, radiation tests were performed on amorphous semiconductor thin film materials and on threshold and memory devices. The influence of flash x-rays and neutron radiation upon the switching voltages, on- and off-state characteristics, dielectric response, optical transmission, absorption band edge and photoconductivity were measured prior to, during and following irradiation. These extensive tests showed the high radiation tolerance of amorphous semiconductor materials. Electrical and optical properties, other than photoconductivity, have a neutron radiation tolerance threshold above 10 17 nvt in the steady state and 10 14 nvt in short (50 μsec to 16 msec) pulses. Photoconductivity increases by 1 1 / 2 orders of magnitude at the level of 10 14 nvt (short pulses of 50 μsec). Super flash x-rays up to 5000 rads (Si), 20 nsec, do not initiate switching in off-state samples which are voltage biased up to 90 percent of the threshold voltage. Both memory and threshold amorphous devices are capable of switching on and off during nuclear radiation transients at least as high as 2 x 10 14 nvt in 50 μsec pulses

  8. Temperature-stress resistance and tolerance along a latitudinal cline in North American Arabidopsis lyrata.

    Directory of Open Access Journals (Sweden)

    Guillaume Wos

    Full Text Available The study of latitudinal gradients can yield important insights into adaptation to temperature stress. Two strategies are available: resistance by limiting damage, or tolerance by reducing the fitness consequences of damage. Here we studied latitudinal variation in resistance and tolerance to frost and heat and tested the prediction of a trade-off between the two strategies and their costliness. We raised plants of replicate maternal seed families from eight populations of North American Arabidopsis lyrata collected along a latitudinal gradient in climate chambers and exposed them repeatedly to either frost or heat stress, while a set of control plants grew under standard conditions. When control plants reached maximum rosette size, leaf samples were exposed to frost and heat stress, and electrolyte leakage (PEL was measured and treated as an estimate of resistance. Difference in maximum rosette size between stressed and control plants was used as an estimate of tolerance. Northern populations were more frost resistant, and less heat resistant and less heat tolerant, but-unexpectedly-they were also less frost tolerant. Negative genetic correlations between resistance and tolerance to the same and different thermal stress were generally not significant, indicating only weak trade-offs. However, tolerance to frost was consistently accompanied by small size under control conditions, which may explain the non-adaptive latitudinal pattern for frost tolerance. Our results suggest that adaptation to frost and heat is not constrained by trade-offs between them. But the cost of frost tolerance in terms of plant size reduction may be important for the limits of species distributions and climate niches.

  9. Adaptive Observer-Based Fault-Tolerant Control Design for Uncertain Systems

    Directory of Open Access Journals (Sweden)

    Huaming Qian

    2015-01-01

    Full Text Available This study focuses on the design of the robust fault-tolerant control (FTC system based on adaptive observer for uncertain linear time invariant (LTI systems. In order to improve robustness, rapidity, and accuracy of traditional fault estimation algorithm, an adaptive fault estimation algorithm (AFEA using an augmented observer is presented. By utilizing a new fault estimator model, an improved AFEA based on linear matrix inequality (LMI technique is proposed to increase the performance. Furthermore, an observer-based state feedback fault-tolerant control strategy is designed, which guarantees the stability and performance of the faulty system. Moreover, the adaptive observer and the fault-tolerant controller are designed separately, whose performance can be considered, respectively. Finally, simulation results of an aircraft application are presented to illustrate the effectiveness of the proposed design methods.

  10. About problematic peculiarities of Fault Tolerance digital regulation organization

    Science.gov (United States)

    Rakov, V. I.; Zakharova, O. V.

    2018-05-01

    The solution of problems concerning estimation of working capacity of regulation chains and possibilities of preventing situations of its violation in three directions are offered. The first direction is working out (creating) the methods of representing the regulation loop (circuit) by means of uniting (combining) diffuse components and forming algorithmic tooling for building predicates of serviceability assessment separately for the components and the for regulation loops (circuits, contours) in general. The second direction is creating methods of Fault Tolerance redundancy in the process of complex assessment of current values of control actions, closure errors and their regulated parameters. The third direction is creating methods of comparing the processes of alteration (change) of control actions, errors of closure and regulating parameters with their standard models or their surroundings. This direction allows one to develop methods and algorithmic tool means, aimed at preventing loss of serviceability and effectiveness of not only a separate digital regulator, but also the whole complex of Fault Tolerance regulation.

  11. use of genetic variability estimates and interrelationships

    African Journals Online (AJOL)

    Prof. Adipala Ekwamu

    of 11 agronomic and biochemical traits to water stress based on estimation of genetic ... of primary branches and 100 seed weight under W0, and number of primary ... selection of superior drought-tolerant genotype (LR1) with good yield ...

  12. Microbial stress tolerance for biofuels. Systems biology

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Zonglin Lewis (ed.) [National Center for Agricultural Utilization Research, USDA-ARS, Peoria, IL (United States)

    2012-07-01

    The development of sustainable and renewable biofuels is attracting growing interest. It is vital to develop robust microbial strains for biocatalysts that are able to function under multiple stress conditions. This Microbiology Monograph provides an overview of methods for studying microbial stress tolerance for biofuels applications using a systems biology approach. Topics covered range from mechanisms to methodology for yeast and bacteria, including the genomics of yeast tolerance and detoxification; genetics and regulation of glycogen and trehalose metabolism; programmed cell death; high gravity fermentations; ethanol tolerance; improving biomass sugar utilization by engineered Saccharomyces; the genomics on tolerance of Zymomonas mobilis; microbial solvent tolerance; control of stress tolerance in bacterial host organisms; metabolomics for ethanologenic yeast; automated proteomics work cell systems for strain improvement; and unification of gene expression data for comparable analyses under stress conditions. (orig.)

  13. SCHEME ANALYSIS TREE DIMENSIONS AND TOLERANCES PROCESSING

    OpenAIRE

    Constanta RADULESCU; Liviu Marius CÎRŢÎNĂ; Constantin MILITARU

    2011-01-01

    This paper presents one of the steps that help us to determine the optimal tolerances depending on thetechnological capability of processing equipment. To determine the tolerances in this way is necessary to takethe study and to represent schematically the operations are used in technological process of making a piece.Also in this phase will make the tree diagram of the dimensions and machining tolerances, dimensions andtolerances shown that the design execution. Determination processes, and ...

  14. Generalized tolerance sensitivity and DEA metric sensitivity

    OpenAIRE

    Neralić, Luka; E. Wendell, Richard

    2015-01-01

    This paper considers the relationship between Tolerance sensitivity analysis in optimization and metric sensitivity analysis in Data Envelopment Analysis (DEA). Herein, we extend the results on the generalized Tolerance framework proposed by Wendell and Chen and show how this framework includes DEA metric sensitivity as a special case. Further, we note how recent results in Tolerance sensitivity suggest some possible extensions of the results in DEA metric sensitivity.

  15. Generalized tolerance sensitivity and DEA metric sensitivity

    Directory of Open Access Journals (Sweden)

    Luka Neralić

    2015-03-01

    Full Text Available This paper considers the relationship between Tolerance sensitivity analysis in optimization and metric sensitivity analysis in Data Envelopment Analysis (DEA. Herein, we extend the results on the generalized Tolerance framework proposed by Wendell and Chen and show how this framework includes DEA metric sensitivity as a special case. Further, we note how recent results in Tolerance sensitivity suggest some possible extensions of the results in DEA metric sensitivity.

  16. Evidence of adaptive tolerance to nickel in isolates of Cenococcum geophilum from serpentine soils.

    Science.gov (United States)

    Gonçalves, Susana C; Martins-Loução, M Amélia; Freitas, Helena

    2009-04-01

    Selection for metal-tolerant ecotypes of ectomycorrhizal (ECM) fungi has been reported in instances of metal contamination of soils as a result of human activities. However, no study has yet provided evidence that natural metalliferous soils, such as serpentine soils, can drive the evolution of metal tolerance in ECM fungi. We examined in vitro Ni tolerance in isolates of Cenococcum geophilum from serpentine and non-serpentine soils to assess whether isolates from serpentine soils exhibited patterns consistent with adaptation to elevated levels of Ni, a typical feature of serpentine. A second objective was to investigate the relationship between Ni tolerance and specific growth rates (micro) among isolates to increase our understanding of possible tolerance/growth trade-offs. Isolates from both soil types were screened for Ni tolerance by measuring biomass production in liquid media with increasing Ni concentrations, so that the effective concentration of Ni inhibiting fungal growth by 50% (EC(50)) could be determined. Isolates of C. geophilum from serpentine soils exhibited significantly higher tolerance to Ni than non-serpentine isolates. The mean Ni EC(50) value for serpentine isolates (23.4 microg ml(-1)) was approximately seven times higher than the estimated value for non-serpentine isolates (3.38 microg ml(-1)). Although there was still a considerable variation in Ni sensitivity among the isolates, none of the serpentine isolates had EC(50) values for Ni within the range found for non-serpentine isolates. We found a negative correlation between EC(50) and micro values among isolates (r = -0.555). This trend, albeit only marginally significant (P = 0.06), indicates a potential trade-off between tolerance and growth, in agreement with selection against Ni tolerance in "normal" habitats. Overall, these results suggest that Ni tolerance arose among serpentine isolates of C. geophilum as an adaptive response to Ni exposure in serpentine soils.

  17. Tolerance of the human spinal cord to single dose radiosurgery

    International Nuclear Information System (INIS)

    Ryu, S.; Zhu, G.; Yin, F.-F.; Ajlouni, M.; Kim, J.H.

    2003-01-01

    Tolerance of the spinal cord to the single dose of radiation is not well defined. Although there are cases of human spinal cord tolerance from re-irradiation to the same cord level, the information about the tolerance of human spinal cord to single large dose of radiosurgery is not available. We carried out spinal radiosurgery to treat spinal metastasis and studied the single dose tolerance of the human spinal cord in an ongoing dose escalation paradigm. A total of 39 patients with 48 lesions of spinal metastasis were treated with single dose radiosurgery at Henry Ford Hospital. The radiosurgery dose was escalated from 8 Gy to 16 Gy at 2 Gy increment. The radiation dose was prescribed to periphery of the spinal tumor. The radiation dose to the spinal cord was estimated by computerized dosimetry. The median follow-up time was 10 months (range 6-18 months) from the radiosurgery. The endpoint of the study was to demonstrate the efficacy of the spinal radiosurgery and to determine the tolerance of human spinal cord to single dose radiosurgery. The dose to the spinal cord was generally less than 50 % of the prescribed radiation dose. The volume of the spinal cord that received higher than this dose was less than 20 % of the anterior portion of the spinal cord. Maximum single dose of 8 Gy was delivered to the anterior 20 % of the spinal cord in this dose escalation study. The dose volume histogram will be presented. There was no acute or subacute radiation toxicity detected clinically and radiologically during the maximum follow-up of 20 months. Further dose escalation is in progress. The single tolerance dose of the human spinal cord appears to be at least 8 Gy when it was given to the 20 % of the cord volume, although the duration of follow up is not long enough to detect severe late cord toxicity. This study offers a valuable radiobiological basis of the normal spinal cord tolerance, and opens spinal radiosurgery as a safe treatment for spinal metastasis

  18. 76 FR 22045 - Fluopicolide; Pesticide Tolerances

    Science.gov (United States)

    2011-04-20

    ... regulation establishes tolerances for residues of fluopicolide and its metabolites in or on multiple... occurred at dose levels where significant maternal toxicity (severe body weight gain decrements and...

  19. Enhancing drought tolerance in C(4) crops.

    Science.gov (United States)

    Lopes, Marta S; Araus, Jose Luis; van Heerden, Philippus D R; Foyer, Christine H

    2011-05-01

    Adaptation to abiotic stresses is a quantitative trait controlled by many different genes. Enhancing the tolerance of crop plants to abiotic stresses such as drought has therefore proved to be somewhat elusive in terms of plant breeding. While many C(4) species have significant agronomic importance, most of the research effort on improving drought tolerance has focused on maize. Ideally, drought tolerance has to be achieved without penalties in yield potential. Possibilities for success in this regard are highlighted by studies on maize hybrids performed over the last 70 years that have demonstrated that yield potential and enhanced stress tolerance are associated traits. However, while our understanding of the molecular mechanisms that enable plants to tolerate drought has increased considerably in recent years, there have been relatively few applications of DNA marker technologies in practical C(4) breeding programmes for improved stress tolerance. Moreover, until recently, targeted approaches to drought tolerance have concentrated largely on shoot parameters, particularly those associated with photosynthesis and stay green phenotypes, rather than on root traits such as soil moisture capture for transpiration, root architecture, and improvement of effective use of water. These root traits are now increasingly considered as important targets for yield improvement in C(4) plants under drought stress. Similarly, the molecular mechanisms underpinning heterosis have considerable potential for exploitation in enhancing drought stress tolerance. While current evidence points to the crucial importance of root traits in drought tolerance in C(4) plants, shoot traits may also be important in maintaining high yields during drought.

  20. Synthesis of Fault-Tolerant Embedded Systems

    DEFF Research Database (Denmark)

    Eles, Petru; Izosimov, Viacheslav; Pop, Paul

    2008-01-01

    This work addresses the issue of design optimization for fault- tolerant hard real-time systems. In particular, our focus is on the handling of transient faults using both checkpointing with rollback recovery and active replication. Fault tolerant schedules are generated based on a conditional...... process graph representation. The formulated system synthesis approaches decide the assignment of fault-tolerance policies to processes, the optimal placement of checkpoints and the mapping of processes to processors, such that multiple transient faults are tolerated, transparency requirements...

  1. Establishing soil loss tolerance: an overview

    Directory of Open Access Journals (Sweden)

    Costanza Di Stefano

    2016-09-01

    Full Text Available Soil loss tolerance is a criterion for establishing if a soil is potentially subjected to erosion risk, productivity loss and if a river presents downstream over-sedimentation or other off-site effects are present at basin scale. At first this paper reviews the concept of tolerable soil loss and summarises the available definitions and the knowledge on the recommended values and evaluating criteria. Then a threshold soil loss value, at the annual temporal scale, established for limiting riling was used for defining the classical soil loss tolerance. Finally, some research needs on tolerable soil loss are listed.

  2. Using Glucose Tolerance Tests to Model Insulin Secretion and Clearance

    Directory of Open Access Journals (Sweden)

    Anthony Shannon

    2005-04-01

    Full Text Available The purpose of the studies described in this paper is to develop theoretically and to validate experimentally mathematical compartment models which can be used to predict plasma insulin levels in patients with diabetes mellitus (DM. In the case of Type 2 Diabetes Mellitus (T2DM, the C-peptide levels in the plasma were measured as part of routine glucose tolerance tests in order to estimate the prehepatic insulin secretion rates. In the case of Type 1 Diabetes Mellitus (T1DM, a radioactive labelled insulin was used to measure the absorption rate of insulin after a subcutaneous injection of insulin. Both models gave close fits between theoretical estimates and experimental data, and, unlike other models, it is not necessary to seed these models with initial estimates.

  3. Bracketing effects on risk tolerance

    Directory of Open Access Journals (Sweden)

    Ester Moher

    2010-08-01

    Full Text Available Research has shown that risk tolerance increases when multiple decisions and associated outcomes are presented together in a broader ``bracket'' rather than one at a time. The present studies disentangle the influence of problem bracketing (presenting multiple investment options together from that of outcome bracketing (presenting the aggregated outcomes of multiple decisions, factors which have been deliberately confounded in previous research. In the standard version of the bracketing task, in which participants decide how much of an initial endowment to invest into each in a series of repeated, identical gambles, we find a problem bracketing effect but not an outcome bracketing effect. However, this pattern of results does not generalize to the cases of non-identical gambles nor discrete choice, where we fail to find the standard bracketing effect.

  4. Euro-Multiculturalism and Toleration

    DEFF Research Database (Denmark)

    Lægaard, Sune

    2014-01-01

    The underlying concept of multiculturalism in many European discussions is different from that made prominent by the classic cases, e.g. in Canada, that have functioned as paradigm cases which the most prominent theories of multiculturalism have been tailored to fit and justify. “Euro-multicultur......The underlying concept of multiculturalism in many European discussions is different from that made prominent by the classic cases, e.g. in Canada, that have functioned as paradigm cases which the most prominent theories of multiculturalism have been tailored to fit and justify. “Euro......, and b) that it is under-inclusive in the sense that it collapses multiculturalism into standard liberal political theory and fails to explain what is distinctive about multiculturalism. Finally the paper shows that multiculturalism in this sense can involve issues of toleration....

  5. Targeting phenotypically tolerant Mycobacterium tuberculosis

    Science.gov (United States)

    Gold, Ben; Nathan, Carl

    2016-01-01

    While the immune system is credited with averting tuberculosis in billions of individuals exposed to Mycobacterium tuberculosis, the immune system is also culpable for tempering the ability of antibiotics to deliver swift and durable cure of disease. In individuals afflicted with tuberculosis, host immunity produces diverse microenvironmental niches that support suboptimal growth, or complete growth arrest, of M. tuberculosis. The physiological state of nonreplication in bacteria is associated with phenotypic drug tolerance. Many of these host microenvironments, when modeled in vitro by carbon starvation, complete nutrient starvation, stationary phase, acidic pH, reactive nitrogen intermediates, hypoxia, biofilms, and withholding streptomycin from the streptomycin-addicted strain SS18b, render M. tuberculosis profoundly tolerant to many of the antibiotics that are given to tuberculosis patients in a clinical setting. Targeting nonreplicating persisters is anticipated to reduce the duration of antibiotic treatment and rate of post-treatment relapse. Some promising drugs to treat tuberculosis, such as rifampicin and bedaquiline, only kill nonreplicating M. tuberculosis in vitro at concentrations far greater than their minimal inhibitory concentrations against replicating bacilli. There is an urgent demand to identify which of the currently used antibiotics, and which of the molecules in academic and corporate screening collections, have potent bactericidal action on nonreplicating M. tuberculosis. With this goal, we review methods of high throughput screening to target nonreplicating M. tuberculosis and methods to progress candidate molecules. A classification based on structures and putative targets of molecules that have been reported to kill nonreplicating M. tuberculosis revealed a rich diversity in pharmacophores. However, few of these compounds were tested under conditions that would exclude the impact of adsorbed compound acting during the recovery phase of

  6. Susceptibility and tolerance of rice crop to salt threat: Physiological and metabolic inspections.

    Directory of Open Access Journals (Sweden)

    Nyuk Ling Ma

    Full Text Available Salinity threat is estimated to reduce global rice production by 50%. Comprehensive analysis of the physiological and metabolite changes in rice plants from salinity stress (i.e. tolerant versus susceptible plants is important to combat higher salinity conditions. In this study, we screened a total of 92 genotypes and selected the most salinity tolerant line (SS1-14 and most susceptible line (SS2-18 to conduct comparative physiological and metabolome inspections. We demonstrated that the tolerant line managed to maintain their water and chlorophyll content with lower incidence of sodium ion accumulation. We also examined the antioxidant activities of these lines: production of ascorbate peroxidase (APX and catalase (CAT were significantly higher in the sensitive line while superoxide dismutase (SOD was higher in the tolerant line. Partial least squares discriminant analysis (PLS-DA score plots show significantly different response for both lines after the exposure to salinity stress. In the tolerant line, there was an upregulation of non-polar metabolites and production of sucrose, GABA and acetic acid, suggesting an important role in salinity adaptation. In contrast, glutamine and putrescine were noticeably high in the susceptible rice. Coordination of different strategies in tolerant and susceptible lines show that they responded differently after exposure to salt stress. These findings can assist crop development in terms of developing tolerance mechanisms for rice crops.

  7. 77 FR 4890 - Damage Tolerance and Fatigue Evaluation for Composite Rotorcraft Structures, and Damage Tolerance...

    Science.gov (United States)

    2012-02-01

    ...-AJ52, 2120-AJ51 Damage Tolerance and Fatigue Evaluation for Composite Rotorcraft Structures, and Damage Tolerance and Fatigue Evaluation for Metallic Structures; Correction AGENCY: Federal Aviation Administration... Tolerance and Fatigue Evaluation for Composite Rotorcraft Structures'' (76 FR 74655), published December 1...

  8. Proposal for new best estimates of the soil-to-plant transfer factor of U, Th, Ra, Pb and Po

    Energy Technology Data Exchange (ETDEWEB)

    Vandenhove, H. [Belgian Nuclear Research Centre, Biosphere Impact Studies, Mol (Belgium)], E-mail: hvandenh@sckcen.be; Olyslaegers, G. [Belgian Nuclear Research Centre, Biosphere Impact Studies, Mol (Belgium); Sanzharova, N.; Shubina, O. [RIAREA, Russian Institute of Agricultural Radiology and Agroecology, Obninsk (Russian Federation); Reed, E. [SENES Oak Ridge Inc., Center for Risk Analysis, Oak Ridge, TN (United States); Shang, Z. [Nuclear Safety Center of SEPA, Beijing (China); Velasco, H. [GEA- IMASL, Universidad Nacional de San Luis, Consejo Nacional de Investigaciones Cientificas y Tecnicas (Argentina)

    2009-09-15

    There is increasing interest in radiological assessment of discharges of naturally occurring radionuclides into the terrestrial environment. Such assessments require parameter values for the pathways considered in predictive models. An important pathway for human exposure is via ingestion of food crops and animal products. One of the key parameters in environmental assessment is therefore the soil-to-plant transfer factor to food and fodder crops. The objective of this study was to compile data, based on an extensive literature survey, concerning soil-to-plant transfer factors for uranium, thorium, radium, lead, and polonium. Transfer factor estimates were presented for major crop groups (Cereals, Leafy vegetables, Non-leafy vegetables, Root crops, Tubers, Fruits, Herbs, Pastures/grasses, Fodder), and also for some compartments within crop groups. Transfer factors were also calculated per soil group, as defined by their texture and organic matter content (Sand, Loam, Clay and Organic), and evaluation of transfer factors' dependency on specific soil characteristics was performed following regression analysis. The derived estimates were compared with estimates currently in use.

  9. Evaluation of digital fault-tolerant architectures for nuclear power plant control systems

    International Nuclear Information System (INIS)

    Battle, R.E.

    1990-01-01

    This paper reports on four fault-tolerant architectures that were evaluated for their potential reliability in service as control systems of nuclear power plants. The reliability analyses showed that human- and software-related common cause failures and single points of failure in the output modules are dominant contributors to system unreliability. The four architectures are triple-modular-redundant, both synchronous and asynchronous, and also dual synchronous and asynchronous. The evaluation includes a review of design features, an analysis of the importance of coverage, and reliability analyses of fault-tolerant systems. Reliability analyses based on data from several industries that have fault-tolerant controllers were used to estimate the mean-time-between-failures of fault-tolerant controllers and to predict those failure modes that may be important in nuclear power plants

  10. A validation methodology for fault-tolerant clock synchronization

    Science.gov (United States)

    Johnson, S. C.; Butler, R. W.

    1984-01-01

    A validation method for the synchronization subsystem of a fault-tolerant computer system is presented. The high reliability requirement of flight crucial systems precludes the use of most traditional validation methods. The method presented utilizes formal design proof to uncover design and coding errors and experimentation to validate the assumptions of the design proof. The experimental method is described and illustrated by validating an experimental implementation of the Software Implemented Fault Tolerance (SIFT) clock synchronization algorithm. The design proof of the algorithm defines the maximum skew between any two nonfaulty clocks in the system in terms of theoretical upper bounds on certain system parameters. The quantile to which each parameter must be estimated is determined by a combinatorial analysis of the system reliability. The parameters are measured by direct and indirect means, and upper bounds are estimated. A nonparametric method based on an asymptotic property of the tail of a distribution is used to estimate the upper bound of a critical system parameter. Although the proof process is very costly, it is extremely valuable when validating the crucial synchronization subsystem.

  11. Religion, tolerance and national development: The Nigerian ...

    African Journals Online (AJOL)

    Tolerance as the ability to bear with one another inspite of differences either in opinion, belief or knowledge is an indispensable factor for any meaningful progress and development of any nation. To a keen observer of the daily happenings in Nigeria, religious tolerance is more than a topical issue because of its relevance ...

  12. Tolerance based algorithms for the ATSP

    NARCIS (Netherlands)

    Goldengorin, B; Sierksma, G; Turkensteen, M; Hromkovic, J; Nagl, M; Westfechtel, B

    2004-01-01

    In this paper we use arc tolerances, instead of arc costs, to improve Branch-and-Bound type algorithms for the Asymmetric Traveling Salesman Problem (ATSP). We derive new tighter lower bounds based on exact and approximate bottleneck upper tolerance values of the Assignment Problem (AP). It is shown

  13. Political Socialization, Tolerance, and Sexual Identity

    Science.gov (United States)

    Avery, Patricia G.

    2002-01-01

    Key concepts in political socialization, tolerance, groups, rights and responsibilities can be used to understand the way in which young people struggle with sexual identity issues. Educators may promote greater tolerance for homosexuality among heterosexuals by situating sexual identity issues within a broader discussion of democratic principles.…

  14. 75 FR 69353 - Isoxaben; Pesticide Tolerances

    Science.gov (United States)

    2010-11-12

    ...; and pistachio. Dow AgroSciences requested these tolerances under the Federal Food, Drug, and Cosmetic... 0.01 ppm; and nut, tree, group 14 and pistachio at 0.03 ppm. That notice referenced a summary of the... the data supporting the petition, EPA has reduced the tolerances for nut, tree, group 14 and pistachio...

  15. 76 FR 27268 - Glyphosate; Pesticide Tolerance

    Science.gov (United States)

    2011-05-11

    ... ENVIRONMENTAL PROTECTION AGENCY 40 CFR Part 180 [EPA-HQ-OPP-2010-0938; FRL-8872-6] Glyphosate... regulation increases the established tolerance for residues of glyphosate in or on corn, field, forage... tolerance for residues of the herbicide glyphosate, N-(phosphonomethyl) glycine, in or on corn, field...

  16. 7 CFR 51.346 - Tolerances.

    Science.gov (United States)

    2010-01-01

    ... Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE REGULATIONS AND STANDARDS UNDER THE AGRICULTURAL MARKETING ACT OF 1946... Standards for Grades of Apples for Processing Tolerances § 51.346 Tolerances. When a lot of apples is...

  17. 7 CFR 51.306 - Tolerances.

    Science.gov (United States)

    2010-01-01

    ... Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing Practices), DEPARTMENT OF AGRICULTURE REGULATIONS AND STANDARDS UNDER THE AGRICULTURAL MARKETING ACT OF 1946... Standards for Grades of Apples Tolerances § 51.306 Tolerances. In order to allow for variations incident to...

  18. 77 FR 60311 - Chlorantraniliprole; Pesticide Tolerances

    Science.gov (United States)

    2012-10-03

    ... sheep, fat to 0.5 ppm. EPA has also increased the existing tolerances in cattle, meat; goat, meat; horse..., horse and sheep, fat at 0.5 ppm, and cattle, goat, horse and sheep, meat at 0.1 ppm. Consistent with the.... Revise the tolerances for cattle, fat; cattle, meat; goat, fat; goat, meat; horse, fat; horse, meat...

  19. Chromium Tolerance and Bioremoval by Cyanobacteria Isolated ...

    African Journals Online (AJOL)

    Two cyanobacterial species Nostoc calcicola HH-12 and Chroococcus minutus HH-11 isolated from a textile mill oxidation pond were examined individually and as consortium for their chromium(VI) tolerance and bioremoval from aqueous solutions. Both species were tolerant to the metal and showed significant increase ...

  20. Effects of Political Knowledge on Political Tolerance

    Science.gov (United States)

    Hall, John Powell

    2018-01-01

    Sexual orientation continues to be an explosive issue in American classrooms. Increasing the political knowledge of students can reduce the volatility of this explosive issue by increasing tolerance toward the lesbian, gay, bisexual, and transgender community. This relationship between political knowledge and political tolerance has been…

  1. Drought tolerant wheat varieties developed through mutation ...

    African Journals Online (AJOL)

    In search for higher yielding drought tolerant wheat varieties, one of the Kenyan high yielding variety 'Pasa' was irradiated with gamma rays (at 150, 200, and 250gy) in 1997 so as to induce variability and select for drought tolerance. Six mutants ((KM10, KM14, KM15, KM18, KM20 and KM21) were selected at M4 for their ...

  2. Stress tolerant crops from nitrogen fixing trees

    Energy Technology Data Exchange (ETDEWEB)

    Becker, R.; Saunders, R.M.

    1983-01-01

    Notes are given on the nutritional quality and uses of: pods of Geoffroea decorticans, a species tolerant of saline and limed soils and saline water; seeds of Olneya tesota which nodulates readily and fixes nitrogen and photosynthesizes at low water potential; and pods of Prosopis chilensis and P. tamarugo which tolerate long periods without rain. 3 references.

  3. Intercultural Education of Tolerance and Hospitality

    Science.gov (United States)

    Dasli, Maria

    2017-01-01

    This paper aims to make a theoretical contribution to the current debate on intercultural education by focusing on the nature and limits of tolerance. Drawing on contemporary theorisations of the concept, it is suggested that while tolerance appears fundamental for confronting issues of difference, it has several caveats. The paper discusses the…

  4. 75 FR 26662 - Fluazinam; Pesticide Tolerances

    Science.gov (United States)

    2010-05-12

    ... due to systemic toxicity and not a result of frank neurotoxicity. No signs of neurotoxicity were... chromatography with electron capture detection (GC/ECD), is available to enforce the tolerance expression for...) enforcement method is also available to enforce the tolerance expression for wine grapes, which includes...

  5. State Toleration, Religious Recognition and Equality

    DEFF Research Database (Denmark)

    Lægaard, Sune

    2013-01-01

    In debates about multiculturalism, it is widely claimed that ‘toleration is not enough’ and that we need to go ‘beyond toleration’ to some form of politics of recognition in order to satisfactorily address contemporary forms of cultural diversity (e.g. the presence in Europe of Muslim minorities...... a conceptual question of whether the relation between states and minorities can be categoriseized in terms of recognition or toleration, but about a normative question of whether and how toleration and recognition secures equality. When toleration is inadequate, this is often because it institutionaliseizes...... and upholds specific inequalities. But politics of recognition may equally well institute inequalities, and in such cases unequal recognition may not be preferable to toleration....

  6. Historical Aspects in Tolerance Phenomenon Research

    Directory of Open Access Journals (Sweden)

    Janat A. Karmanova

    2013-01-01

    Full Text Available The article examines the historical aspect of the tolerance phenomenon research, particularly the study of tolerance in the age of Antiquity, Middle Ages, New Times, Enlightenment. It is remarkable that the problem of tolerance, emerged in Western civilization on religious grounds, laid the foundation for all other freedoms, attained in many countries. Besides, the article attaches special attention to the researchers of the East, such as Abu Nasr al-Farabi, Khoja Ahmed Yasawi, studies the historical aspect of works by Kazakhstan thinkers A. Kunanbayev, C. Valikhanova, K.B. Zharikbayev, S.K. Kaliyev, A.N. Nysanbayev, A.I. Artemev and others. The analysis of historical research of the tolerance phenomenon brings the author to the conclusion that religious freedom was the starting point for the emergence of new areas of tolerance display. The content of this phenomenon changed according to the historical peculiarities of the societies’ development

  7. Diagnosis and fault-tolerant control

    CERN Document Server

    Blanke, Mogens; Lunze, Jan; Staroswiecki, Marcel

    2016-01-01

    Fault-tolerant control aims at a gradual shutdown response in automated systems when faults occur. It satisfies the industrial demand for enhanced availability and safety, in contrast to traditional reactions to faults, which bring about sudden shutdowns and loss of availability. The book presents effective model-based analysis and design methods for fault diagnosis and fault-tolerant control. Architectural and structural models are used to analyse the propagation of the fault through the process, to test the fault detectability and to find the redundancies in the process that can be used to ensure fault tolerance. It also introduces design methods suitable for diagnostic systems and fault-tolerant controllers for continuous processes that are described by analytical models of discrete-event systems represented by automata. The book is suitable for engineering students, engineers in industry and researchers who wish to get an overview of the variety of approaches to process diagnosis and fault-tolerant contro...

  8. Algorithms for worst-case tolerance optimization

    DEFF Research Database (Denmark)

    Schjær-Jacobsen, Hans; Madsen, Kaj

    1979-01-01

    New algorithms are presented for the solution of optimum tolerance assignment problems. The problems considered are defined mathematically as a worst-case problem (WCP), a fixed tolerance problem (FTP), and a variable tolerance problem (VTP). The basic optimization problem without tolerances...... is denoted the zero tolerance problem (ZTP). For solution of the WCP we suggest application of interval arithmetic and also alternative methods. For solution of the FTP an algorithm is suggested which is conceptually similar to algorithms previously developed by the authors for the ZTP. Finally, the VTP...... is solved by a double-iterative algorithm in which the inner iteration is performed by the FTP- algorithm. The application of the algorithm is demonstrated by means of relatively simple numerical examples. Basic properties, such as convergence properties, are displayed based on the examples....

  9. Cognitive component of Tolerance in Pedagogic Education

    Directory of Open Access Journals (Sweden)

    O. V. Akimova

    2013-01-01

    Full Text Available The paper looks at one of the urgent educational problems of tolerance development by teachers and students; tolerance being viewed as the openness to the new knowledge acquisition, willingness to understand other people and cooperate with them, and therefore the opportunity for self- development.The paper outlines the ways of tolerant attitudes formation by all the human subjects of educational process; the concept of person oriented teaching is considered to be the basic one for tolerance development. To optimize the specialists’ training for communication at any level of professional environment, the cognitive activity educational model is suggested, providing the ways out of any complicated pedagogical situation. The cognitive psychology concepts give the background for the above model. The education in question promotes the intellectual level of the prospective teachers, intensifies their creative potential, methodological thinking and practical experience, as well as tolerance development in professional communication process. 

  10. Cognitive Ability, Principled Reasoning and Political Tolerance

    DEFF Research Database (Denmark)

    Hebbelstrup Rye Rasmussen, Stig; Nørgaard, Asbjørn Sonne

    Individuals are not equally politically tolerant. To explain why, individual differences in emotions and threat have received much scholarly attention in recent years. However, extant research also shows that psychological dispositions, habitual cognitive styles, ideological orientation...... and ‘principled reasoning’ influence political tolerance judgments. The extent to which cognitive ability plays a role has not been entertained even if the capacity to think abstractly, comprehend complex ideas and apply abstract ideas to concrete situations is inherent to both principled tolerance judgment...... and cognitive ability. Cognitive ability, we argue and show, adds to the etiology of political tolerance. In Danish and American samples cognitive ability strongly predicts political tolerance after taking habitual cognitive styles (as measured by personality traits), education, social ideology, and feelings...

  11. 40 CFR 180.564 - Indoxacarb; tolerances for residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Indoxacarb; tolerances for residues...) PESTICIDE PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.564 Indoxacarb; tolerances for residues. (a) General. Tolerances are established for residues of...

  12. Fault-tolerant and Diagnostic Methods for Navigation

    DEFF Research Database (Denmark)

    Blanke, Mogens

    2003-01-01

    to diagnose faults and autonomously provide valid navigation data, disregarding any faulty sensor data and use sensor fusion to obtain a best estimate for users. This paper discusses how diagnostic and fault-tolerant methods are applicable in marine systems. An example chosen is sensor fusion for navigation......Precise and reliable navigation is crucial, and for reasons of safety, essential navigation instruments are often duplicated. Hardware redundancy is mostly used to manually switch between instruments should faults occur. In contrast, diagnostic methods are available that can use analytic redundancy...

  13. Tissue tolerance under the combination treatment of maxillary cancer

    International Nuclear Information System (INIS)

    Egawa, Jun; Ono, Isamu; Suzuki, Kunio; Takeda, Chisato; Ebihara, Satoshi.

    1977-01-01

    The tissue tolerance doses of the maxillary sinus structures were estimated when they were subjected to treatment for maxillary cancer by the usual combination of surgery, radiotherapy and regional arterial infusion of 5-fluorouracil. Equivalent single dose calculation was applied with irreversible tissue damage as an indicator. The retardation of epithelialization of the maxillary sinus operated upon appeared to be correlated with the dose delivered. The study indicated that 2,200 rad expressed by equivalent single dose is a safe dose level for sufficient epithelialization. The safety dose level for the bony structure, exposed by surgery, seemed to be at 1,800 rad. (auth.)

  14. Tissue tolerance under the combination treatment of maxillary cancer

    Energy Technology Data Exchange (ETDEWEB)

    Egawa, J [Teikyo Univ., Tokyo (Japan). Faculty of Medicine; Ono, I; Suzuki, K; Takeda, C; Ebihara, S

    1977-06-01

    The tissue tolerance doses of the maxillary sinus structures were estimated when they were subjected to treatment for maxillary cancer by the usual combination of surgery, radiotherapy, and regional arterial infusion of 5-fluorouracil. Equivalent single dose calculation was applied with irreversible tissue damage as an indicator. The retardation of epithelialization of the maxillary sinus operated upon appeared to be correlated with the dose delivered. The study indicated that 2,200 rad expressed by equivalent single dose is a safe dose level for sufficient epithelialization. The safety dose level for the bony structure, exposed by surgery, seemed to be at 1,800 rad.

  15. Estimation of past radon exposure to indoor radon from embedded 210Po in household glass

    International Nuclear Information System (INIS)

    Gusain, G. S.; Rautela, B. S.; Ramola, R. C.

    2012-01-01

    In the present investigation, the surface-deposited polonium activities were measured in houses in the Ukhimath region of Garhwal Himalaya (India)). The surface-deposited 210 Po activity concentrations were found to vary from 0.7 to 15.40 Bq m -2 with an average of 5.95 Bq m -2 . The radon concentration estimated on the basis of 210 Po activity was found to vary from 0.29 to 700 Bq m -3 with an average value 242 Bq m -3 . The contemporary radon concentration in the area was found to vary from 13 to 181 Bq m -3 with an average of 46 Bq m -3 . The annual effective dose due to 210 Po activity in houses in the Garhwal Himalaya region was found to vary from 0.61 to 13.33 mSv with an average of 5.15 mSv. Some worldwide studies have shown the relation between the increased risk of lung cancer and smoking habits. Data on smoking have also been collected from the same dwellings. The significance of this work is also discussed in detail from a radiation protection point of view. (authors)

  16. Heated Allergens and Induction of Tolerance in Food Allergic Children

    Directory of Open Access Journals (Sweden)

    Irmeli Penttila

    2013-06-01

    Full Text Available Food allergies are one of the first manifestations of allergic disease and have been shown to significantly impact on general health perception, parental emotional distress and family activities. It is estimated that in the Western world, almost one in ten children have an IgE-mediated allergy. Cow’s milk and egg allergy are common childhood allergies. Until recently, children with food allergy were advised to avoid all dietary exposure to the allergen to which they were sensitive, in the thought that consumption would exacerbate their allergy. However, recent publications indicate that up to 70% of children with egg allergy can tolerate egg baked in a cake or muffin without apparent reaction. Likewise, up to 75% of children can tolerate baked goods containing cow’s milk, and these children demonstrate IgE and IgG4 profiles indicative of tolerance development. This article will review the current literature regarding the use of heated food allergens as immunotherapy for children with cow’s milk and egg allergy.

  17. Induced tolerance from a sublethal insecticide leads to cross-tolerance to other insecticides.

    Science.gov (United States)

    Hua, Jessica; Jones, Devin K; Relyea, Rick A

    2014-04-01

    As global pesticide use increases, the ability to rapidly respond to pesticides by increasing tolerance has important implications for the persistence of nontarget organisms. A recent study of larval amphibians discovered that increased tolerance can be induced by an early exposure to low concentrations of a pesticide. Since natural systems are often exposed to a variety of pesticides that vary in mode of action, we need to know whether the induction of increased tolerance to one pesticide confers increased tolerance to other pesticides. Using larval wood frogs (Lithobates sylvaticus), we investigated whether induction of increased tolerance to the insecticide carbaryl (AChE-inhibitor) can induce increased tolerance to other insecticides that have the same mode of action (chlorpyrifos, malathion) or a different mode of action (Na(+)channel-interfering insecticides; permethrin, cypermethrin). We found that embryonic exposure to sublethal concentrations of carbaryl induced higher tolerance to carbaryl and increased cross-tolerance to malathion and cypermethrin but not to chlorpyrifos or permethrin. In one case, the embryonic exposure to carbaryl induced tolerance in a nonlinear pattern (hormesis). These results demonstrate that that the newly discovered phenomenon of induced tolerance also provides induced cross-tolerance that is not restricted to pesticides with the same mode of action.

  18. UAV remote sensing for phenotyping drought tolerance in peanuts

    Science.gov (United States)

    Balota, Maria; Oakes, Joseph

    2017-05-01

    Farmers can benefit from growing drought tolerant peanut (Arachis hypogaea L.) cultivars with improved yield when rainfall is sporadic. In the Virginia-Carolina (VC) region, drought is magnified by hot summers and usually occurs in July and Aug when pod and seed growth are intense. At these growth stages, weekly supply of 50 to 75 mm of water is needed to ensure profitability. Irrigation can supplement crop water needs, but only 10% of the peanut farms are irrigated. In this frame, drought tolerant varieties can be profitable, but breeding for cultivars with improved drought tolerance requires fast yet accurate phenotyping. Our objective was to evaluate the potential of UAV remote sensing technologies for drought tolerance selection in peanut. In this study, we examined the effect of drought on leaf wilting, pod yield, grading characteristics, and crop value of 23 peanut cultivars (Virginia, Runner, and Valencia type). These varieties were arranged in a factorial design, with four replications drought stressed and two replications well-watered. Drought was imposed by covering the drought stressed plots with rainout shelters on July 19; they remained covered until August 29 and only received 38 mm irrigation in mid Aug. The well-watered plots continued to receive rain and supplemental irrigation as needed. During this time, Canopy Temperature Depression (CT) and Normalized Differential Vegetative Index (NDVI) were collected from the ground on all plots at weekly intervals. After the shelters were removed, these measurements were collected daily for approximately 2 weeks. At the same time, Red-Green-Blue (RGB), near-infrared (NIR), and infrared (IR) images taken from an UAV platform were also collected. Vegetation indices derived from the ground and aerial data were compared with leaf wilting, pod yield and crop value. Wilting, which is a common water stress symptom, was best estimated by NDVI and RGB, and least by CT; but CT was best in estimating yield, SMK and

  19. The tolerability of risk from nuclear power stations: a discussion of the HSE's guidelines

    International Nuclear Information System (INIS)

    Ryder, E.A.; Woods, P.B.

    1989-01-01

    The Health and Safety Executive's discussion document, ''The Tolerability of risk from nuclear power stations'', published just a year ago considers the concept of risk and the broad principles of risk assessment and proposes guidelines on the tolerable levels of individual and societal risks from normal operation and from accidents at nuclear power stations. This paper discusses how these guidelines might be applied in safety assessments so as to ensure an acceptable level of safety and considers some of the problems inherent in the estimation of risk from nuclear power stations. It shows how the tolerable risk levels of the Health and Safety Executive's document are related to the standards used by HM Nuclear Installations Inspectorate when licensing nuclear installations. Some of the uncertainties in the estimation of acceptable risk are discussed as are the acceptance criteria used by the Inspectorate in its assessments of both normal and accident situations. (author)

  20. Fraud: zero tolerance at CERN

    CERN Multimedia

    2014-01-01

    In this week’s Bulletin (see here), you’ll read that fraudulent activities were uncovered last year by our Internal Audit Service. CERN has a very clearly defined policy in such cases: we base our efforts on prevention through education, we have a policy of protecting those reporting fraud from recrimination, and we have a zero-tolerance policy should fraud be uncovered.   I don’t intend to enter into the details of what occurred, but I’d like to remind you that fraud is a very grave business, and something we take extremely seriously. What do we mean by fraud at CERN? Operational Circular No. 10 on “Principles and procedures governing the investigation of fraud” defines fraud in terms of any deception intended to benefit the perpetrator, or a third party, that results in a loss to the Organization. This loss can be to funds, property or reputation. Thankfully, fraud at CERN is a rare occurrence, but we should never be complacent. ...

  1. Uranium, radon-222 and polonium-210 in drinking waters from metropolitan area of Recife, PE, Brazil; Uranio, radonio-222 e polonio-210 em aguas de abastecimento publico da regiao metropolitana do Recife

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Cleomacio Miguel da

    2000-04-01

    There is only scarce information on the presence of radionuclides in water for public consumption in Brazil. A recently issued federal regulation requires that waters from public supplies be screened to determine their content of alpha and beta emitters. In order to comply with this requirement the present work was carried out with the purpose of determining the concentration of natural uranium, {sup 222} Rn and {sup 210} Po in water supplies in the metropolitan region of Recife, Brazil. The analyses were performed in 17 points of supply of superficial water and 94 points of groundwater supply. The concentrations of uranium were determined by the fluorimetric method, whereas the liquid scintillation method was used to determine the concentration of {sup 222} Rn. Polonium-210, on the other hand, was determined by alpha spectrometry, following its spontaneous deposition on copper disks. The water analyzer presented uranium concentrations varying from 35.3 to 1146.5 mBq/L for superficial resources and from 20.2 to 919.15 mBq/L for underground sources. The concentration of uranium in superficial water showed significant correlation with some parameters such as conductivity, alkalinity and total hardness, as well as, with the concentrations of Ca, Mg, Cl, K, SO{sub 4} and Mn. No correlation, however, was shown with the concentrations of Fe, NO{sub 2} and NO{sub 3}. The concentrations of {sup 222} Rn varied from 5.3 to 83.7 Bq/L in the groundwater analyzer. Radon concentration was not measured in superficial water due to the high emanation rate of radon in open air conditions. As far as {sup 210} Po is concerned, the analyses showed concentrations ranging from <22 mBq/L (the lowest limit of detection) to 57.4 mBq/L for superficial water and from <22 to 813 mBq/L for ground water samples. The concentrations of {sup 210} Po did not show and correlation with physico-chemical parameters. The average concentrations of uranium and {sup 210} Po in superficial water were of 44

  2. A Fault-tolerant RISC Microprocessor for Spacecraft Applications

    Science.gov (United States)

    Timoc, Constantin; Benz, Harry

    1990-01-01

    Viewgraphs on a fault-tolerant RISC microprocessor for spacecraft applications are presented. Topics covered include: reduced instruction set computer; fault tolerant registers; fault tolerant ALU; and double rail CMOS logic.

  3. Regulatory focus affects physician risk tolerance.

    Science.gov (United States)

    Veazie, Peter J; McIntosh, Scott; Chapman, Benjamin P; Dolan, James G

    2014-01-01

    Risk tolerance is a source of variation in physician decision-making. This variation, if independent of clinical concerns, can result in mistaken utilization of health services. To address such problems, it will be helpful to identify nonclinical factors of risk tolerance, particularly those amendable to intervention-regulatory focus theory suggests such a factor. This study tested whether regulatory focus affects risk tolerance among primary care physicians. Twenty-seven primary care physicians were assigned to promotion-focused or prevention-focused manipulations and compared on the Risk Taking Attitudes in Medical Decision Making scale using a randomization test. Results provide evidence that physicians assigned to the promotion-focus manipulation adopted an attitude of greater risk tolerance than the physicians assigned to the prevention-focused manipulation (p = 0.01). The Cohen's d statistic was conventionally large at 0.92. Results imply that situational regulatory focus in primary care physicians affects risk tolerance and may thereby be a nonclinical source of practice variation. Results also provide marginal evidence that chronic regulatory focus is associated with risk tolerance (p = 0.05), but the mechanism remains unclear. Research and intervention targeting physician risk tolerance may benefit by considering situational regulatory focus as an explanatory factor.

  4. Software fault tolerance in computer operating systems

    Science.gov (United States)

    Iyer, Ravishankar K.; Lee, Inhwan

    1994-01-01

    This chapter provides data and analysis of the dependability and fault tolerance for three operating systems: the Tandem/GUARDIAN fault-tolerant system, the VAX/VMS distributed system, and the IBM/MVS system. Based on measurements from these systems, basic software error characteristics are investigated. Fault tolerance in operating systems resulting from the use of process pairs and recovery routines is evaluated. Two levels of models are developed to analyze error and recovery processes inside an operating system and interactions among multiple instances of an operating system running in a distributed environment. The measurements show that the use of process pairs in Tandem systems, which was originally intended for tolerating hardware faults, allows the system to tolerate about 70% of defects in system software that result in processor failures. The loose coupling between processors which results in the backup execution (the processor state and the sequence of events occurring) being different from the original execution is a major reason for the measured software fault tolerance. The IBM/MVS system fault tolerance almost doubles when recovery routines are provided, in comparison to the case in which no recovery routines are available. However, even when recovery routines are provided, there is almost a 50% chance of system failure when critical system jobs are involved.

  5. Frustration Tolerance in Youth With ADHD.

    Science.gov (United States)

    Seymour, Karen E; Macatee, Richard; Chronis-Tuscano, Andrea

    2016-06-08

    The objective of this study was to compare children with ADHD with children without ADHD on frustration tolerance and to examine the role of oppositional defiant disorder (ODD) in frustration tolerance within the sample. Participants included 67 children ages 10 to 14 years-old with (n = 37) and without (n = 30) Diagnostic and Statistical Manual of Mental Disorders (4th ed.; DSM-IV) ADHD who completed the Mirror Tracing Persistence Task (MTPT), a validated computerized behavioral measure of frustration tolerance. Children with ADHD were more likely to quit this task than children without ADHD, demonstrating lower levels of frustration tolerance. There were no differences in frustration tolerance between children with ADHD + ODD and those with ADHD - ODD. Moreover, ODD did not moderate the relationship between ADHD and frustration tolerance. Our results suggest that low frustration tolerance is directly linked to ADHD and not better accounted for by ODD. This research highlights specific behavioral correlates of frustration in children with ADHD. © The Author(s) 2016.

  6. Tolerance to environmental desiccation in moss sperm.

    Science.gov (United States)

    Shortlidge, Erin E; Rosenstiel, Todd N; Eppley, Sarah M

    2012-05-01

    • Sexual reproduction in mosses requires that sperm be released freely into the environment before finding and fertilizing a receptive female. After release from the male plant, moss sperm may experience a range of abiotic stresses; however, few data are available examining stress tolerance of moss sperm and whether there is genetic variation for stress tolerance in this important life stage. • Here, we investigated the effects of environmental desiccation and recovery on the sperm cells of three moss species (Bryum argenteum, Campylopus introflexus, and Ceratodon purpureus). • We found that a fraction of sperm cells were tolerant to environmental desiccation for extended periods (d) and that tolerance did not vary among species. We found that this tolerance occurs irrespective of ambient dehydration conditions, and that the addition of sucrose during dry-down improved cell recovery. Although we observed no interspecific variation, significant variation among individuals within species in sperm cell tolerance to environmental desiccation was observed, suggesting selection could potentially act on this basic reproductive trait. • The observation of desiccation-tolerant sperm in multiple moss species has important implications for understanding bryophyte reproduction, suggesting the presence of a significant, uncharacterized complexity in the ecology of moss mating systems. © 2012 The Authors. New Phytologist © 2012 New Phytologist Trust.

  7. State of art in radiation tolerant camera

    Energy Technology Data Exchange (ETDEWEB)

    Choi; Young Soo; Kim, Seong Ho; Cho, Jae Wan; Kim, Chang Hoi; Seo, Young Chil

    2002-02-01

    Working in radiation environment such as nuclear power plant, RI facility, nuclear fuel fabrication facility, medical center has to be considered radiation exposure, and we can implement these job by remote observation and operation. However the camera used for general industry is weakened at radiation, so radiation-tolerant camera is needed for radiation environment. The application of radiation-tolerant camera system is nuclear industry, radio-active medical, aerospace, and so on. Specially nuclear industry, the demand is continuous in the inspection of nuclear boiler, exchange of pellet, inspection of nuclear waste. In the nuclear developed countries have been an effort to develop radiation-tolerant cameras. Now they have many kinds of radiation-tolerant cameras which can tolerate to 10{sup 6}-10{sup 8} rad total dose. In this report, we examine into the state-of-art about radiation-tolerant cameras, and analyze these technology. We want to grow up the concern of developing radiation-tolerant camera by this paper, and upgrade the level of domestic technology.

  8. Oral Tolerance: Therapeutic Implications for Autoimmune Diseases

    Directory of Open Access Journals (Sweden)

    Ana M. C. Faria

    2006-01-01

    Full Text Available Oral tolerance is classically defined as the suppression of immune responses to antigens (Ag that have been administered previously by the oral route. Multiple mechanisms of tolerance are induced by oral Ag. Low doses favor active suppression, whereas higher doses favor clonal anergy/deletion. Oral Ag induces Th2 (IL-4/IL-10 and Th3 (TGF-β regulatory T cells (Tregs plus CD4+CD25+ regulatory cells and LAP+T cells. Induction of oral tolerance is enhanced by IL-4, IL-10, anti-IL-12, TGF-β, cholera toxin B subunit (CTB, Flt-3 ligand, anti-CD40 ligand and continuous feeding of Ag. In addition to oral tolerance, nasal tolerance has also been shown to be effective in suppressing inflammatory conditions with the advantage of a lower dose requirement. Oral and nasal tolerance suppress several animal models of autoimmune diseases including experimental allergic encephalomyelitis (EAE, uveitis, thyroiditis, myasthenia, arthritis and diabetes in the nonobese diabetic (NOD mouse, plus non-autoimmune diseases such as asthma, atherosclerosis, colitis and stroke. Oral tolerance has been tested in human autoimmune diseases including MS, arthritis, uveitis and diabetes and in allergy, contact sensitivity to DNCB, nickel allergy. Positive results have been observed in phase II trials and new trials for arthritis, MS and diabetes are underway. Mucosal tolerance is an attractive approach for treatment of autoimmune and inflammatory diseases because of lack of toxicity, ease of administration over time and Ag-specific mechanism of action. The successful application of oral tolerance for the treatment of human diseases will depend on dose, developing immune markers to assess immunologic effects, route (nasal versus oral, formulation, mucosal adjuvants, combination therapy and early therapy.

  9. Field Quality from Tolerance Stack-up In R&D Quadrupoles for the Advanced Photon Source Upgrade

    Energy Technology Data Exchange (ETDEWEB)

    Liu, J.; Jaski, M.; Dejus, R.; Doose, C.; Donnelly, A.; Downey, J.; Borland, M.; Jain, Animesh

    2016-10-01

    The Advanced Photon Source (APS) at Argonne National Laboratory (ANL) is considering upgrading the current double-bend, 7-GeV, 3rd generation storage ring to a 6-GeV, 4th generation storage ring with a Multibend Achromat (MBA) lattice. In this study, a novel method is proposed to determine fabrication and assembly tolerances through a combination of magnetic and mechanical tolerance analyses. Mechanical tolerance stackup analyses using Teamcenter Variation Analysis are carried out to determine the part and assembly level fabrication tolerances. Finite element analyses using OPERA are conducted to estimate the effect of fabrication and assembly errors on the magnetic field of a quadrupole magnet and to determine the allowable tolerances to achieve the desired magnetic performance. Finally, results of measurements in R&D quadrupole prototypes are compared with the analysis results.

  10. Tolerance Optimization for Mechanisms with Lubricated Joints

    International Nuclear Information System (INIS)

    Choi, J.-H.; Lee, S.J.; Choi, D.-H.

    1998-01-01

    This paper addresses an analytical approach to tolerance optimization for planar mechanisms with lubricated joints based on mechanical error analysis. The mobility method is applied to consider the lubrication effects at joints and planar mechanisms are stochastically defined by using the clearance vector model for mechanical error analysis. The uncertainties considered in the analysis are tolerances on link lengths and radial clearances and these are selected as design variables. To show the validity of the proposed method for mechanical error analysis, it is applied to two examples, and the results obtained are compared with those of Monte Carlo simulations. Based on the mechanical error analysis, tolerance optimizations are applied to the examples

  11. Concatenated codes for fault tolerant quantum computing

    Energy Technology Data Exchange (ETDEWEB)

    Knill, E.; Laflamme, R.; Zurek, W.

    1995-05-01

    The application of concatenated codes to fault tolerant quantum computing is discussed. We have previously shown that for quantum memories and quantum communication, a state can be transmitted with error {epsilon} provided each gate has error at most c{epsilon}. We show how this can be used with Shor`s fault tolerant operations to reduce the accuracy requirements when maintaining states not currently participating in the computation. Viewing Shor`s fault tolerant operations as a method for reducing the error of operations, we give a concatenated implementation which promises to propagate the reduction hierarchically. This has the potential of reducing the accuracy requirements in long computations.

  12. Fault tolerant control design for hybrid systems

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Hao; Jiang, Bin [Nanjing University of Aeronautics and Astronautics, Nanjing (China); Cocquempot, Vincent [Universite des Sciences et Technologies de Lille, Villeneuve d' Ascq (France)

    2010-07-01

    This book intends to provide the readers a good understanding on how to achieve Fault Tolerant Control goal of Hybrid Systems. The book can be used as a reference for the academic research on Fault Tolerant Control and Hybrid Systems or used in Ph.D. study of control theory and engineering. The knowledge background for this monograph would be some undergraduate and graduate courses on Fault Diagnosis and Fault Tolerant Control theory, linear system theory, nonlinear system theory, Hybrid Systems theory and Discrete Event System theory. (orig.)

  13. SCHEME ANALYSIS TREE DIMENSIONS AND TOLERANCES PROCESSING

    Directory of Open Access Journals (Sweden)

    Constanta RADULESCU

    2011-07-01

    Full Text Available This paper presents one of the steps that help us to determine the optimal tolerances depending on thetechnological capability of processing equipment. To determine the tolerances in this way is necessary to takethe study and to represent schematically the operations are used in technological process of making a piece.Also in this phase will make the tree diagram of the dimensions and machining tolerances, dimensions andtolerances shown that the design execution. Determination processes, and operations of the dimensions andtolerances tree scheme will make for a machined piece is both indoor and outdoor.

  14. A Need for Dialogue to Develop Tolerance

    Directory of Open Access Journals (Sweden)

    Corina Yoris-Villasana

    2016-03-01

    Full Text Available The authoress claims that civic education must be grounded in a deep sense of belonging, which, in turn, involves values such as freedom, equality, civility, justice, pluralism and, above all, ensures the development of dialogue and tolerance in the individual, dialogue and tolerance which are essential attributes of a democratic attitude. Tolerance and dialogue are the pivots of citizenship in a society which is to function peacefully. She concludes that by developing these values individuals can better participate in the pursuit of social ideals.

  15. Tolerance – a Culturally Dependent Concept?

    Directory of Open Access Journals (Sweden)

    Trond Jørgensen

    2014-12-01

    Full Text Available This article presents research on Japanese interpretations of the first article of the Universal Declaration of Human Rights as a point of departure for discussing how the Japanese cultural contexts present an alternative understanding of tolerance to the Western liberal. According to Rainer Forst, tolerance is a normatively dependent concept (Forst 2010. This implies that the specific cultural values or the ‘normative context’ and environment become relevant. Since the praxis of tolerance always takes place in a specific cultural and moral environment, the cultural context influences how tolerance is carried out in practice as well as the norms defining its limits. Japanese informants held that cultural norms and values in Japan differ somewhat from those in the West. They perceived the human rights discourse as culturally dependent and culturally marked and clearly considered the first article of the Universal Declaration of Human Rights to be a product of Western thought. It states that ‘All human beings are born free and equal in dignity and rights. They are endowed with reason and conscience and should act towards one another in the spirit of brotherhood’ (United Nations 1948. While the role of tolerance in Western political philosophy seems to be attached to liberal values of autonomy and freedom, the Confucian-influenced environment in Japan places more emphasis on inter-dependency, cultivation, and learning social rules and proper-place-occupation as bases for moral conduct and deserving of respect. According to the Japanese informants, people are not ‘born with rights’ or ‘born free and equal’. Maintaining harmony, consensus, and proper behaviour according to relationships and hierarchy creates a different kind of setting for tolerance. The inter-dependent perspectives of Japanese culture may restrain freedom and can thus be expected to limit toleration of divergent views or behaviour. The culture-specific perception of

  16. An architecture for fault tolerant controllers

    DEFF Research Database (Denmark)

    Niemann, Hans Henrik; Stoustrup, Jakob

    2005-01-01

    degradation in the sense of guaranteed degraded performance. A number of fault diagnosis problems, fault tolerant control problems, and feedback control with fault rejection problems are formulated/considered, mainly from a fault modeling point of view. The method is illustrated on a servo example including......A general architecture for fault tolerant control is proposed. The architecture is based on the (primary) YJBK parameterization of all stabilizing compensators and uses the dual YJBK parameterization to quantify the performance of the fault tolerant system. The approach suggested can be applied...

  17. Fault Tolerant Control: A Simultaneous Stabilization Result

    DEFF Research Database (Denmark)

    Stoustrup, Jakob; Blondel, V.D.

    2004-01-01

    This paper discusses the problem of designing fault tolerant compensators that stabilize a given system both in the nominal situation, as well as in the situation where one of the sensors or one of the actuators has failed. It is shown that such compensators always exist, provided that the system...... is detectable from each output and that it is stabilizable. The proof of this result is constructive, and a worked example shows how to design a fault tolerant compensator for a simple, yet challeging system. A family of second order systems is described that requires fault tolerant compensators of arbitrarily...

  18. Limits of tolerance as a social phenomenon

    Directory of Open Access Journals (Sweden)

    Stepanenko Serhiy Ihorovych

    2016-10-01

    Full Text Available This article covers an insufficiently studied scientific and social topic; it seeks to make clear if there are any boundaries in terms of tolerance. The problem of tolerance has a pivotal role nowadays. Its significance can be explained by the existence of many factors: multiculturalism as the process of worsening of international relations, terrorism, the development of the religious extremism, the problems with refugees etc. In order to solve these issues, it is crucial to consider the essence and peculiarities of tolerance in society.

  19. 75 FR 22234 - Phosphate Ester, Tallowamine, Ethoxylated; Exemption from the Requirement of a Tolerance

    Science.gov (United States)

    2010-04-28

    ...) parameters were observed. The gestation index was decreased primarily due to mortality of females. Decreased... surrogate information to derive upper bound exposure estimates for the subject inert ingredient. Upper bound... highest tolerance level from the surrogate pesticides for every food, and 100% crop treated is assumed for...

  20. 76 FR 38026 - Diethylene Glycol Mono Butyl Ether; Exemption From the Requirement of a Tolerance

    Science.gov (United States)

    2011-06-29

    ... in creatinine levels at >51 mg/kg/day. Confidence in this study is low because of the high... at the high dose (117 mg/m3). In addition, the selected study was more recent and one would expect... estimates are based on the highest tolerance for a given commodity from a list of high-use insecticides...

  1. Active Fault-Tolerant Control for Wind Turbine with Simultaneous Actuator and Sensor Faults

    Directory of Open Access Journals (Sweden)

    Lei Wang

    2017-01-01

    Full Text Available The purpose of this paper is to show a novel fault-tolerant tracking control (FTC strategy with robust fault estimation and compensating for simultaneous actuator sensor faults. Based on the framework of fault-tolerant control, developing an FTC design method for wind turbines is a challenge and, thus, they can tolerate simultaneous pitch actuator and pitch sensor faults having bounded first time derivatives. The paper’s key contribution is proposing a descriptor sliding mode method, in which for establishing a novel augmented descriptor system, with which we can estimate the state of system and reconstruct fault by designing descriptor sliding mode observer, the paper introduces an auxiliary descriptor state vector composed by a system state vector, actuator fault vector, and sensor fault vector. By the optimized method of LMI, the conditions for stability that estimated error dynamics are set up to promote the determination of the parameters designed. With this estimation, and designing a fault-tolerant controller, the system’s stability can be maintained. The effectiveness of the design strategy is verified by implementing the controller in the National Renewable Energy Laboratory’s 5-MW nonlinear, high-fidelity wind turbine model (FAST and simulating it in MATLAB/Simulink.

  2. Onset of deformation in polonium nuclei

    Energy Technology Data Exchange (ETDEWEB)

    Younes, W.; Cizewski, J.A. [Rutgers Univ., New Brunswick, NJ (United States)

    1996-12-31

    The authors have been able to reproduce the systematics of the positive-parity states in {sup 192-208}Po within the framework of the Particle-Core Model. The wave-functions of the 2{sup +}{sub 1} states have been extracted using the Quasiparticle Random Phase Approximation. The increase in the collective motion of the lighter isotopes comes from the increased proton-neutron interaction when the neutrons and protons both occupy high-j orbitals.

  3. The Litvinenko 210polonium case. German experiences

    International Nuclear Information System (INIS)

    Kroeger, Emily Alice

    2009-01-01

    The high scientific standards of the BfS were necessary in order to characterize and evaluate the low activities of 210 Po found during the deployment in Hamburg. The evaluation of the measurements enabled the BfS to offer effective radiation protection advice and to assist the police investigation. The majority of the 210 Po traces were found in places that had been in skin contact with Kovtun, leading to the conclusion that Kovtun had most probably incorporated 210 Po before his visit to Hamburg in October 2006. As yet, no formal charges have been brought by the German authorities against Kovtun and the costs of the operation remain under discussion. Strategies to improve the internal and external deployment communication of the ZUB are being developed and implemented to deal with both the real and the perceived threats that occur during such an incident. Open communication from the onset of a deployment is essential, both between the institutions involved and between deployment leaders and the press. This will save precious time and resources, lower anxiety in the public and emergency workers and could, in a culture of trust where radiation protection advice is listened to and followed, ultimately save lives. (orig.)

  4. Polonium-210 as Weapon for Mass Destruction

    International Nuclear Information System (INIS)

    Koteng, A.O.

    2010-01-01

    Properties of Po-210 make it possible for its use as weapon of mass destruction. Po-210 occurs naturally in minute quantities in the human body, in Uranium ore (< 0.1 mg Po-210 / ton ) and as a product of Radon-222 gas decay chain. Po-210 also occurs as deposition on vegetation (tobacco leaves). Po-210 is produced by bombardment of Bi-209 with neutrons in a nuclear reactor. Russia produces 8 grams per year for export to USA market

  5. Polonium-210 in Euphauslids: A Detailed Study

    Energy Technology Data Exchange (ETDEWEB)

    Heyraud, M.; Fowler, S. W.; Beasley, T. M.; Cherry, R. D.

    1976-07-01

    A detailed study of {sup 210}Po, the predominant alpha-emitting nuclide found in most marine organisms, has been undertaken in a particular zooplanktonic species, the euphausiid Meganyctiphanes norvegica. The purpose was to obtain information concerning the origin, the localization and the flux of the nuclide in and through this organism. Measurements of {sup 210}Po were made in euphausiids of different sizes, in dissected organs and tissues, and in excretion products. The results show higher concentrations in the smaller specimens; this fact cannot be explained on the basis of surface adsorption, but is probably related to the ingestion of food. Dissection results show that the distribution of {sup 210}Po in euphausiids is not homogeneous, but that the majority is concentrated in the internal organs, the alimentary tract and the hepatopancreas in particular. The natural radiation dose received by these organs is in consequence much higher than that received by the whole animal. Use of a dynamic model allowed the flux of {sup 210}Po through M. norvegica to be calculated. The calculations confirm that food is the principal sauce of {sup 210}Po for this species, and clearly show that fecal pellets constitute the major elimination route. Extrapolation of the data to zooplankton in general leads to the conclusion that zooplankton metabolic activity plays an important role in transporting {sup 210}Po from the surface layers of the ocean to depth. (author)

  6. Polonium-210 in Euphauslids: A Detailed Study

    International Nuclear Information System (INIS)

    Heyraud, M.; Fowler, S.W.; Beasley, T.M.; Cherry, R.D.

    1976-01-01

    A detailed study of 210 Po, the predominant alpha-emitting nuclide found in most marine organisms, has been undertaken in a particular zooplanktonic species, the euphausiid Meganyctiphanes norvegica. The purpose was to obtain information concerning the origin, the localization and the flux of the nuclide in and through this organism. Measurements of 210 Po were made in euphausiids of different sizes, in dissected organs and tissues, and in excretion products. The results show higher concentrations in the smaller specimens; this fact cannot be explained on the basis of surface adsorption, but is probably related to the ingestion of food. Dissection results show that the distribution of 210 Po in euphausiids is not homogeneous, but that the majority is concentrated in the internal organs, the alimentary tract and the hepatopancreas in particular. The natural radiation dose received by these organs is in consequence much higher than that received by the whole animal. Use of a dynamic model allowed the flux of 210 Po through M. norvegica to be calculated. The calculations confirm that food is the principal sauce of 210 Po for this species, and clearly show that fecal pellets constitute the major elimination route. Extrapolation of the data to zooplankton in general leads to the conclusion that zooplankton metabolic activity plays an important role in transporting 210 Po from the surface layers of the ocean to depth. (author)

  7. Polonium-210 in euphausiids: a detailed study

    Energy Technology Data Exchange (ETDEWEB)

    Heyraud, M; Fowler, S W; Beasley, T M; Cherry, R D

    1976-02-13

    A detailed study of /sup 210/Po, the predominant alpha-emitting nuclide found in most marine organisms, has been undertaken in a particular zooplanktonic species, the euphausiid Meganyctiphanes norvegica. Information was obtained concerning the origin, the localization and the flux of the nuclide in and through the organism. Measurements of /sup 210/Po were made in euphausiids of different sizes, in dissected organs and tissues, and in excretion products. The results show higher concentrations in the smaller specimens; this fact cannot be explained on the basis of surface adsorption, but is probably related to the ingestion of food. Dissection results show that the distribution of /sup 210/Po in euphausiids is not homogeneous, but that the majority is concentrated in the internal organs, the alimentary tract and the hepatopancreas in particular. The natural radiation dose received by these organs is in consequence much higher than that received by the whole animal. Use of a dynamic model allowed the flux of /sup 210/Po through M. norvegica to be calculated. The calculations confirm that food is the principal source of /sup 210/Po for this species, and clearly show that fecal pellets constitute the major elimination route. Extrapolation of the data to zooplankton in general leads to the conclusion that zooplankton metabolic activity plays an important role in transporting /sup 210/Po from the surface layers of the ocean to depth. (auth)

  8. Prevalence of impaired glucose tolerance and insulin resistance among obese children and adolescents

    Directory of Open Access Journals (Sweden)

    Robabeh Ghergherechi

    2010-07-01

    Full Text Available Robabeh Ghergherechi1, Ali Tabrizi21Department of Pediatrics Endocrinology, Tabriz University of Medical Sciences, Tabriz, Iran; 2Students’ Research Committee, Tabriz University of Medical Sciences, Tabriz, IranPurpose: Obesity is one of the most important nutritional disorders in the world which has an obvious relationship with the incidence of metabolic diseases. Obesity prevalence has increased among children and adolescents during recent decades, leading to a rise in Type 2 diabetes mellitus (DM II prevalence in these two age brackets. Hence, the aim of this study was to assess impaired glucose tolerance and insulin resistance, and gather metabolic findings in obese children and adolescents.Methods and materials: We studied 110 obese children and adolescents (body mass index > 95th percentile for age and gender 4–18 years of age referred to the endocrine clinic of the Children’s Hospital at Tabriz University in a descriptive cross-sectional study. ­Fasting glucose, insulin, and lipid profile in all subjects were determined. Oral glucose tolerance test after eating 75 g/kg glucose was performed. Homeostatic model assessment was used to ­estimate insulin resistance.Results: Impaired glucose tolerance and insulin resistance prevalence in 68 obese adolescents was 14.7% and 31.8%, respectively. Impaired glucose tolerance and insulin resistance was not seen in 23.8% of 42 obese children. No case of DM II was seen. There was a significant statistical difference in glucose (P = 0.003 and insulin (P < 0.001 level at minute 120 in individuals with impaired glucose tolerance compared to obese children and adolescents without impaired glucose tolerance. Rate of insulin resistance in patients with impaired glucose tolerance was greater and had a significant statistical difference (P = 0.03.Conclusion: Obesity has a close relationship with increased risk of impaired glucose tolerance and insulin resistance in children and adolescents. Oral glucose

  9. Reconfigurable fault tolerant avionics system

    Science.gov (United States)

    Ibrahim, M. M.; Asami, K.; Cho, Mengu

    This paper presents the design of a reconfigurable avionics system based on modern Static Random Access Memory (SRAM)-based Field Programmable Gate Array (FPGA) to be used in future generations of nano satellites. A major concern in satellite systems and especially nano satellites is to build robust systems with low-power consumption profiles. The system is designed to be flexible by providing the capability of reconfiguring itself based on its orbital position. As Single Event Upsets (SEU) do not have the same severity and intensity in all orbital locations, having the maximum at the South Atlantic Anomaly (SAA) and the polar cusps, the system does not have to be fully protected all the time in its orbit. An acceptable level of protection against high-energy cosmic rays and charged particles roaming in space is provided within the majority of the orbit through software fault tolerance. Check pointing and roll back, besides control flow assertions, is used for that level of protection. In the minority part of the orbit where severe SEUs are expected to exist, a reconfiguration for the system FPGA is initiated where the processor systems are triplicated and protection through Triple Modular Redundancy (TMR) with feedback is provided. This technique of reconfiguring the system as per the level of the threat expected from SEU-induced faults helps in reducing the average dynamic power consumption of the system to one-third of its maximum. This technique can be viewed as a smart protection through system reconfiguration. The system is built on the commercial version of the (XC5VLX50) Xilinx Virtex5 FPGA on bulk silicon with 324 IO. Simulations of orbit SEU rates were carried out using the SPENVIS web-based software package.

  10. Fault Tolerant Control for Civil Structures Based on LMI Approach

    Directory of Open Access Journals (Sweden)

    Chunxu Qu

    2013-01-01

    Full Text Available The control system may lose the performance to suppress the structural vibration due to the faults in sensors or actuators. This paper designs the filter to perform the fault detection and isolation (FDI and then reforms the control strategy to achieve the fault tolerant control (FTC. The dynamic equation of the structure with active mass damper (AMD is first formulated. Then, an estimated system is built to transform the FDI filter design problem to the static gain optimization problem. The gain is designed to minimize the gap between the estimated system and the practical system, which can be calculated by linear matrix inequality (LMI approach. The FDI filter is finally used to isolate the sensor faults and reform the FTC strategy. The efficiency of FDI and FTC is validated by the numerical simulation of a three-story structure with AMD system with the consideration of sensor faults. The results show that the proposed FDI filter can detect the sensor faults and FTC controller can effectively tolerate the faults and suppress the structural vibration.

  11. Estimating Utility

    DEFF Research Database (Denmark)

    Arndt, Channing; Simler, Kenneth R.

    2010-01-01

    A fundamental premise of absolute poverty lines is that they represent the same level of utility through time and space. Disturbingly, a series of recent studies in middle- and low-income economies show that even carefully derived poverty lines rarely satisfy this premise. This article proposes a......, with the current approach tending to systematically overestimate (underestimate) poverty in urban (rural) zones.......A fundamental premise of absolute poverty lines is that they represent the same level of utility through time and space. Disturbingly, a series of recent studies in middle- and low-income economies show that even carefully derived poverty lines rarely satisfy this premise. This article proposes...... an information-theoretic approach to estimating cost-of-basic-needs (CBN) poverty lines that are utility consistent. Applications to date illustrate that utility-consistent poverty measurements derived from the proposed approach and those derived from current CBN best practices often differ substantially...

  12. Downy mildew intensity in tolerant grapes varieties in highlands of southern Brazil

    Directory of Open Access Journals (Sweden)

    de Bem Betina

    2016-01-01

    Full Text Available The aim of this study was to evaluate the different degrees of tolerance to infection by P. viticolaamong three genotypes with constitutive resistance in comparison to susceptible varieties Vitis vinifera. For this purpose two experiments was conducted at EPAGRI Experimental Station, located in the city of São Joaquim, Santa Catarina State, at 2015/16 cycle. In the first experiment on the field, were quantified the incidence and severity and downy mildew intensity was compared by epidemiological variables, on the tolerant varieties Bronner, Regent, Cabernet Cortis and the susceptible Sangiovese. On the second experiment forty leaf discs for the same tolerant genotypes and the susceptible variety Chardonnay were artificially infected with P. viticola sporangia suspension and after seven days of incubation the discs were examined and the degree of infection was estimated based on the intensity of sporangiophore formation. Sangiovese showed highest downy mildew intensity in comparison to the tolerant varieties Cabernet Carbon, Regent and Bronner. Under controlled conditions, the susceptible variety Chardonnay showed higher sporangiophore formation on discs leafs in comparison to the tolerant varieties. All the downy mildew tolerant varieties evaluated showed lower disease development in comparison with V. vinifera varieties.

  13. Oxygen tolerance test : A standardised protocol

    Directory of Open Access Journals (Sweden)

    D K Ghosh

    2015-01-01

    Conclusion: By following a standardised protocol for Oxygen Tolerance Test, an objective assessment and recordkeeping is possible. This shall entail a more effective screening during the initial diving medical examination.

  14. Ionic liquid-tolerant cellulase enzymes

    Science.gov (United States)

    Gladden, John; Park, Joshua; Singer, Steven; Simmons, Blake; Sale, Ken

    2017-10-31

    The present invention provides ionic liquid-tolerant cellulases and method of producing and using such cellulases. The cellulases of the invention are useful in saccharification reactions using ionic liquid treated biomass.

  15. Mast cell degranulation breaks peripheral tolerance.

    Science.gov (United States)

    de Vries, V C; Wasiuk, A; Bennett, K A; Benson, M J; Elgueta, R; Waldschmidt, T J; Noelle, R J

    2009-10-01

    Mast cells (MC) have been shown to mediate regulatory T-cell (T(reg))-dependent, peripheral allograft tolerance in both skin and cardiac transplants. Furthermore, T(reg) have been implicated in mitigating IgE-mediated MC degranulation, establishing a dynamic, reciprocal relationship between MC and T(reg) in controlling inflammation. In an allograft tolerance model, it is now shown that intragraft or systemic MC degranulation results in the transient loss of T(reg) suppressor activities with the acute, T-cell dependent rejection of established, tolerant allografts. Upon degranulation, MC mediators can be found in the skin, T(reg) rapidly leave the graft, MC accumulate in the regional lymph node and the T(reg) are impaired in the expression of suppressor molecules. Such a dramatic reversal of T(reg) function and tissue distribution by MC degranulation underscores how allergy may causes the transient breakdown of peripheral tolerance and episodes of acute T-cell inflammation.

  16. Spinoza and the Theory of Active Tolerance

    DEFF Research Database (Denmark)

    Tønder, Lars

    2013-01-01

    This paper considers the politics of tolerance through the lens of Spinoza’s philosophy of immanence. The contention is that Spinoza’s philosophy of immanence provides us with a better conceptualization of the relationship between tolerance and power, and that it in so doing reinvigorates a theory...... of active tolerance that, for the most part, has been lost in contemporary democratic theory. Spinoza’s philosophy of immanence does so because it animates a sensorial orientation to politics, one that heightens our attention to the affective components of political life, enabling us to better theorize how...... all modes of existence, including the so-called passive ones, harbor a degree of power that can be mobilized for purposes that go beyond the “non-practice” highlighted by advocates and critics of tolerance in contemporary democratic theory. The paper develops this argument with ongoing reference...

  17. Risk tolerance: A perspective on entrepreneurship education

    African Journals Online (AJOL)

    Southern African Business Review Volume 13 Number 3 2009 ... be covered for each audience, and which specific pedagogical methods will most ... whose research suggests that entrepreneurs do indeed exhibit a higher risk tolerance.

  18. 77 FR 59558 - Sulfentrazone; Pesticide Tolerances

    Science.gov (United States)

    2012-09-28

    ... hay; wheat grain; wheat straw; and cowpea, succulent. The human health risk assessment used to support... Tolerances in/on: Rhubarb, Turnip Roots and Tops, Sunflower Subgroup 20B, Succulent Cowpea, Succulent Lima...

  19. Tolerances of the human brain to concussion.

    Science.gov (United States)

    1971-03-01

    The report reviews the pertinent literature and adds additional evidence indicating that the human brain may be able to tolerate head impact forces in the range of 300 to 400 g's without evidence of concussion or other detectable neurologic sequelae,...

  20. Physiological and molecular insights into drought tolerance ...

    African Journals Online (AJOL)

    Physiological and molecular insights into drought tolerance. Sagadevan G Mundree, Bienyameen Baker, Shaheen Mowla, Shaun Peters, Saberi Marais, Clare Vander Willigen, Kershini Govender, Alice Maredza, Samson Muyanga, Jill M Farrant, Jennifer A Thomson ...

  1. Selection and characterisation of high ethanol tolerant ...

    African Journals Online (AJOL)

    STORAGESEVER

    2008-12-17

    Dec 17, 2008 ... High level ethanol tolerant Saccharomyces yeast, Orc 6, was investigated for its potential application ... sources include cashew, apple juice (Osho, 2005), palm ... choice for fermentation (Chandra and Panchal, 2003). Yeasts ...

  2. Definition of tolerable soil erosion values

    Directory of Open Access Journals (Sweden)

    G. Sparovek

    1997-09-01

    Full Text Available Although the criteria for defining erosion tolerance are well established, the limits generally used are not consistent with natural, economical and technological conditions. Rates greater than soil formation can be accepted only until a minimum of soil depth is reached, provided that they are not associated with environmental hazard or productivity losses. A sequence of equations is presented to calculate erosion tolerance rates through time. The selection of equation parameters permits the definition of erosion tolerance rates in agreement with environmental, social and technical needs. The soil depth change that is related to irreversible soil degradation can be calculated. The definition of soil erosion tolerance according to these equations can be used as a guideline for sustainable land use planning and is compatible with expert systems.

  3. Real-Time Fault Tolerant Networking Protocols

    National Research Council Canada - National Science Library

    Henzinger, Thomas A

    2004-01-01

    We made significant progress in the areas of video streaming, wireless protocols, mobile ad-hoc and sensor networks, peer-to-peer systems, fault tolerant algorithms, dependability and timing analysis...

  4. Tolerance analysis through computational imaging simulations

    Science.gov (United States)

    Birch, Gabriel C.; LaCasse, Charles F.; Stubbs, Jaclynn J.; Dagel, Amber L.; Bradley, Jon

    2017-11-01

    The modeling and simulation of non-traditional imaging systems require holistic consideration of the end-to-end system. We demonstrate this approach through a tolerance analysis of a random scattering lensless imaging system.

  5. Ayurvedic Amalaki Rasayana promotes improved stress tolerance

    Indian Academy of Sciences (India)

    Ayurvedic Amalaki Rasayana promotes improved stress tolerance and thus ... and some otheringredients, and is used for general good health and healthy aging. ... Wild-type larvae/flies rearedon AR-supplemented food survived the various ...

  6. Defining Resistance and Tolerance to Cancer

    Directory of Open Access Journals (Sweden)

    Adler R. Dillman

    2015-11-01

    Full Text Available There are two ways to maintain fitness in the face of infection: resistance is a host’s ability to reduce microbe load and disease tolerance is the ability of the host to endure the negative health effects of infection. Resistance and disease tolerance should be applicable to any insult to the host and have been explored in depth with regards to infection but have not been examined in the context of cancer. Here, we establish a framework for measuring and separating resistance and disease tolerance to cancer in Drosophila melanogaster. We plot a disease tolerance curve to cancer in wild-type flies and then compare this to natural variants, identifying a line with reduced cancer resistance. Quantitation of these two traits opens an additional dimension for analysis of cancer biology.

  7. Supraclassical consequence relations: Tolerating rare counterexamples

    CSIR Research Space (South Africa)

    Labuschagne, W

    2013-12-01

    Full Text Available We explore a family of supraclassical consequence relations obtained by varying the criteria according to which counterexamples to classical entailment may be deemed tolerable. This provides a different perspective on the rational consequence...

  8. 78 FR 46267 - Trifluralin; Pesticide Tolerance

    Science.gov (United States)

    2013-07-31

    ...), trifluralin was tested up to the limit dose (1000 mg/kg/day) and caused no systemic toxicity. Handler exposure... detection (ECD)) is available to enforce the tolerance expression. The method may be requested from: Chief...

  9. 77 FR 3617 - Etoxazole; Pesticide Tolerances

    Science.gov (United States)

    2012-01-25

    ... similar doses, indicating that systemic effects (mainly liver effects) occur at similar dose levels... chromatography/mass selective detection (GC/MSD) methods) are available to enforce the tolerance expression. The...

  10. 78 FR 13252 - Pyroxasulfone; Pesticide Tolerances

    Science.gov (United States)

    2013-02-27

    ... moderately toxic to rats following a 4-week dermal exposure producing local inflammation and systemic effects...) method) is available to enforce the tolerance expression. The method may be requested from: Chief...

  11. 76 FR 50893 - Fluoxastrobin; Pesticide Tolerances

    Science.gov (United States)

    2011-08-17

    ... 30 days)..... None: There were no systemic or dermal toxicity findings in a 28-day dermal toxicity... to enforce the tolerance expression. Method No. 00604 is available for plant commodities and Method...

  12. 78 FR 76987 - Mandipropamid; Pesticide Tolerances

    Science.gov (United States)

    2013-12-20

    ... screening battery. No systemic or dermal toxicity was observed following dermal exposure for 28 days, up to... mass spectrometric detection (LC/MS/MS), is available to enforce the tolerance expression. The method...

  13. 78 FR 44440 - Imazosulfuron; Pesticide Tolerances

    Science.gov (United States)

    2013-07-24

    ... NOAEL is clearly defined, less than or equal to the offspring NOAEL and based on general systemic... chromatography method with tandem mass spectroscopy detection (LC/MS/ MS)) is available to enforce the tolerance...

  14. 78 FR 60715 - Sedaxane; Pesticide Tolerances

    Science.gov (United States)

    2013-10-02

    ... 28-day dermal study did not show systemic toxicity at the limit dose of 1,000 milligrams/kilogram/day... Enforcement Methodology Adequate enforcement methodology is available to enforce the tolerance expression. A...

  15. Genetic behavior of morpho-physiological traits and their role for breeding drought tolerant wheat

    International Nuclear Information System (INIS)

    Saleem, S.; Kashif, M.

    2016-01-01

    The development of drought tolerant and high yielding varieties/germplasm is the major objective of any wheat breeding program. In the present study genetic architecture of physiological traits, yield and yield related parameters were studied using the generation mean analysis to improve grain yield under drought stress. A drought tolerant line, 9877 and a drought susceptible line, NR371 were crossed to develop six generations (P/sub 1/, P/sub 2/, F/sub 1/, BC/sub 1/, BC/sub 2/, and F/sub 2/). Results revealed additive, dominant and epistatic effects involved in the inheritance of characters which varied with trait and stress. Additive gene action was observed for canopy temperature, Chlorophyll a and turgor potential. Although narrow sense heritability estimates for some traits were low but canopy temperature, chlorophyll a and turgor potential expressed reasonably high heritability that supports the results of gene action providing an opportunity for early generation selection to use in a breeding program. The estimation of heritability for leaf carotenoids and turgor potential along with gene action for leaf carotenoids is a new work in wheat. The findings of present study suggested that physiological and bio-chemical traits are the indicators of stress tolerance and their utilization in developing high yielding drought tolerant wheat germplasm can expedite the breeding for stress tolerance. (author)

  16. TOLERANCE: FEATURES AND PROBLEMS OF EVALUATION

    Directory of Open Access Journals (Sweden)

    M. V. Karmanov

    2018-01-01

    Full Text Available In the media and in specialized literature, publications related to attempts to assess the place and role of tolerance in the life of modern society are increasingly encountered. In this connection, a comprehensive scientific analysis of tolerance as an independent and distinctive object of applied research is of great scientific and practical interest. Considering the points of view on the category of "tolerance" gave grounds to believe that there are a number of "white spots" and gaps of methodological nature that do not allow collecting reliable information and identify the main indicators characterizing the state and features of the transformation of tolerance as a social norm reflecting changes in society's value orientations . Tolerance as a characteristic of the moral state of society is a "medal with two sides": on the one hand, it is positive that it promotes mutual understanding, taking into account the recognition of rights and freedoms, with the coordination of different motives, attitudes and orientations without violence and suppression of human dignity, allows to smooth existing irreconcilable interethnic, interethnic, racial contradictions; on the other negative, because it can be perceived as permissiveness, and instill indifference to values. All of the above was justification for the need to present in the article a critical analysis of approaches to the definition and directions of the study of tolerance, which made it possible to reveal its principal features as a complex and multifaceted object of statistical research. In order to implement the principle of objectivity of conclusions, the study was conducted using the following methods: analysis and synthesis, comparison and comparison, generalization, the method of scientific abstraction. The article presents a substantiation of the possibilities of making a quantitative assessment of changes in tolerance in time, taking into account the analysis of information sources

  17. Social Studies Teachers’ Perceptions of Tolerance

    Directory of Open Access Journals (Sweden)

    Hatice Türe

    2014-10-01

    Full Text Available Problem: Tolerance is one of the values which citizens should have in today's multicultural and democratic society. Educational system should teach tolerance to the individuals in a democratic society. Tolerance can be given through curricula in educational process. Social studies is one of the courses for conducting tolerance education. Skills and perspectives of teachers are important for tolerance education in social studies. The purpose of this study is to understand social studies teachers' perceptions of tolerance. Method: In the study, qualitative research method and phenomenology that is one of the qualitative research designs was employed. The participants were determined using criterion sampling. 10 social studies teachers graduated from social studies education departments working at schools of Eskisehir Provincial Directorate of National Education participated in the study. The research process consisted of two phases. The data were gathered through semi-structured interviews. The interviews were conducted in two steps in order to make an in-depth analysis. In Phase I of the study, semi-structured interviews were conducted with 10 teachers in December and January months during the 2012-2013 school year. The data obtained from the first interviews were also the base for the questions in the second interviews. In Phase II of the study, semi-structured interviews were again conducted with 10 teachers who participated in the first interviews in April and May months during the 2012-2013 school year. Teacher Interview Form-1 in the first interviews and Teacher Interview Form-2 in the second interviews were used for data collection. As for data analysis, thematic analysis technique was used. The data were analysed, the findings were defined and interpreted based on the research questions. Findings: The findings of the study revealed that the social studies teachers described tolerance as respecting ideas, values, beliefs and behaviors

  18. Energy-efficient fault-tolerant systems

    CERN Document Server

    Mathew, Jimson; Pradhan, Dhiraj K

    2013-01-01

    This book describes the state-of-the-art in energy efficient, fault-tolerant embedded systems. It covers the entire product lifecycle of electronic systems design, analysis and testing and includes discussion of both circuit and system-level approaches. Readers will be enabled to meet the conflicting design objectives of energy efficiency and fault-tolerance for reliability, given the up-to-date techniques presented.

  19. Design and measurements of SEU tolerant latches

    CERN Document Server

    Menouni, M; Barbero, M; Beccherle, R; Breugnon, P; Ely, R; Fougeron, D; García-Sciveres, M; Gnani, D; Hemperek, T; Karagounis, M; Kluit, R; Mekkaoui, A; Rozanov, A; Schipper, J-D

    2008-01-01

    Latches based on the Dual Interlocked storage Cell or DICE are very tolerant to Single Event Upsets (SEU). However, for highly scaled processes where the sizes continue to decrease, the data in this latch can be corrupted by an SEU due to charge sharing between adjacent nodes. Some layout considerations are used to improve the tolerance of the DICE latches to SEU and especially the influence of sensitive nodes separation is tested for DICE latches designed with a 130 nm process.

  20. Drought Tolerance in Modern and Wild Wheat

    Science.gov (United States)

    Budak, Hikmet; Kantar, Melda; Yucebilgili Kurtoglu, Kuaybe

    2013-01-01

    The genus Triticum includes bread (Triticum aestivum) and durum wheat (Triticum durum) and constitutes a major source for human food consumption. Drought is currently the leading threat on world's food supply, limiting crop yield, and is complicated since drought tolerance is a quantitative trait with a complex phenotype affected by the plant's developmental stage. Drought tolerance is crucial to stabilize and increase food production since domestication has limited the genetic diversity of crops including wild wheat, leading to cultivated species, adapted to artificial environments, and lost tolerance to drought stress. Improvement for drought tolerance can be achieved by the introduction of drought-grelated genes and QTLs to modern wheat cultivars. Therefore, identification of candidate molecules or loci involved in drought tolerance is necessary, which is undertaken by “omics” studies and QTL mapping. In this sense, wild counterparts of modern varieties, specifically wild emmer wheat (T. dicoccoides), which are highly tolerant to drought, hold a great potential. Prior to their introgression to modern wheat cultivars, drought related candidate genes are first characterized at the molecular level, and their function is confirmed via transgenic studies. After integration of the tolerance loci, specific environment targeted field trials are performed coupled with extensive analysis of morphological and physiological characteristics of developed cultivars, to assess their performance under drought conditions and their possible contributions to yield in certain regions. This paper focuses on recent advances on drought related gene/QTL identification, studies on drought related molecular pathways, and current efforts on improvement of wheat cultivars for drought tolerance. PMID:23766697

  1. A Fault Tolerant Integrated Circuit Memory

    OpenAIRE

    Barton, Anthony Francis

    1980-01-01

    Most commercially produced integrated circuits are incapable of tolerating manufacturing defects. The area and function of the circuits is thus limited by the probability of faults occurring within the circuit. This thesis examines techniques for using redundancy in memory circuits to provide fault tolerance and to increase storage capacity. A hierarchical memory architecture using multiple Hamming codes is introduced and analysed to determine its resistance to manufa...

  2. Drought Tolerance in Modern and Wild Wheat

    Directory of Open Access Journals (Sweden)

    Hikmet Budak

    2013-01-01

    Full Text Available The genus Triticum includes bread (Triticum aestivum and durum wheat (Triticum durum and constitutes a major source for human food consumption. Drought is currently the leading threat on world's food supply, limiting crop yield, and is complicated since drought tolerance is a quantitative trait with a complex phenotype affected by the plant's developmental stage. Drought tolerance is crucial to stabilize and increase food production since domestication has limited the genetic diversity of crops including wild wheat, leading to cultivated species, adapted to artificial environments, and lost tolerance to drought stress. Improvement for drought tolerance can be achieved by the introduction of drought-grelated genes and QTLs to modern wheat cultivars. Therefore, identification of candidate molecules or loci involved in drought tolerance is necessary, which is undertaken by “omics” studies and QTL mapping. In this sense, wild counterparts of modern varieties, specifically wild emmer wheat (T. dicoccoides, which are highly tolerant to drought, hold a great potential. Prior to their introgression to modern wheat cultivars, drought related candidate genes are first characterized at the molecular level, and their function is confirmed via transgenic studies. After integration of the tolerance loci, specific environment targeted field trials are performed coupled with extensive analysis of morphological and physiological characteristics of developed cultivars, to assess their performance under drought conditions and their possible contributions to yield in certain regions. This paper focuses on recent advances on drought related gene/QTL identification, studies on drought related molecular pathways, and current efforts on improvement of wheat cultivars for drought tolerance.

  3. Establishing soil loss tolerance: an overview

    OpenAIRE

    Costanza Di Stefano; Vito Ferro

    2016-01-01

    Soil loss tolerance is a criterion for establishing if a soil is potentially subjected to erosion risk, productivity loss and if a river presents downstream over-sedimentation or other off-site effects are present at basin scale. At first this paper reviews the concept of tolerable soil loss and summarises the available definitions and the knowledge on the recommended values and evaluating criteria. Then a threshold soil loss value, at the annual temporal scale, established for limiting rilin...

  4. Henri Fayol and Zero Tolerance Policies

    OpenAIRE

    Lee SCHIMMOELLER

    2012-01-01

    Zero tolerance policies have been increasingly popular in both education and business. Henri Fayol was the one of the earliest and influential thinkers in modern management theory. He defined management as a body of knowledge and defined his 14 administrative principles. It is an interesting exercise to apply Fayol’s teachings to the theory of zero tolerance and attempt to determine what Fayol would think of this new management technique.

  5. Bacterial cells with improved tolerance to polyamines

    DEFF Research Database (Denmark)

    2017-01-01

    Provided are bacterial cells genetically modified to improve their tolerance to certain commodity chemicals, such as polyamines, and methods of preparing and using such bacterial cells for production of polyamines and other compounds.......Provided are bacterial cells genetically modified to improve their tolerance to certain commodity chemicals, such as polyamines, and methods of preparing and using such bacterial cells for production of polyamines and other compounds....

  6. Bacterial cells with improved tolerance to polyols

    DEFF Research Database (Denmark)

    2017-01-01

    The present invention relates to bacterial cells genetically modified to improve their tolerance to certain commodity chemicals, such as diols and other polyols, and to methods of preparing and using such bacterial cells for production of polyols and other compounds.......The present invention relates to bacterial cells genetically modified to improve their tolerance to certain commodity chemicals, such as diols and other polyols, and to methods of preparing and using such bacterial cells for production of polyols and other compounds....

  7. Particle Filter Based Fault-tolerant ROV Navigation using Hydro-acoustic Position and Doppler Velocity Measurements

    DEFF Research Database (Denmark)

    Zhao, Bo; Blanke, Mogens; Skjetne, Roger

    2012-01-01

    This paper presents a fault tolerant navigation system for a remotely operated vehicle (ROV). The navigation system uses hydro-acoustic position reference (HPR) and Doppler velocity log (DVL) measurements to achieve an integrated navigation. The fault tolerant functionality is based on a modied...... particle lter. This particle lter is able to run in an asynchronous manner to accommodate the measurement drop out problem, and it overcomes the measurement outliers by switching observation models. Simulations with experimental data show that this fault tolerant navigation system can accurately estimate...

  8. Radiation tolerance of the pig kidney: a model for determining overall time and fraction factors for preserving renal function

    International Nuclear Information System (INIS)

    Hopewell, J.W.

    1975-01-01

    The Ellis Nominal Standard Dose system has attracted clinical interest for estimating irregular treatment schedules in radiotherapy. This study attempts to examine the system applied to renal tolerance in swine by looking for some regular relationship between time, dose, and fractionation. Also examined was renal function up to two years after treatment. These data indicate that renal tolerance may not be predictable by any simple mathematical expression

  9. Among-population variation in tolerance to larval herbivory by Anthocharis cardamines in the polyploid herb Cardamine pratensis.

    Directory of Open Access Journals (Sweden)

    Malin A E König

    Full Text Available Plants have two principal defense mechanisms to decrease fitness losses to herbivory: tolerance, the ability to compensate fitness after damage, and resistance, the ability to avoid damage. Variation in intensity of herbivory among populations should result in variation in plant defense levels if tolerance and resistance are associated with costs. Yet little is known about how levels of tolerance are related to resistance and attack intensity in the field, and about the costs of tolerance. In this study, we used information about tolerance and resistance against larval herbivory by the butterfly Anthocharis cardamines under controlled conditions together with information about damage in the field for a large set of populations of the perennial plant Cardamine pratensis. Plant tolerance was estimated in a common garden experiment where plants were subjected to a combination of larval herbivory and clipping. We found no evidence of that the proportion of damage that was caused by larval feeding vs. clipping influenced plant responses. Damage treatments had a negative effect on the three measured fitness components and also resulted in an earlier flowering in the year after the attack. Tolerance was related to attack intensity in the population of origin, i.e. plants from populations with higher attack intensity were more likely to flower in the year following damage. However, we found no evidence of a relationship between tolerance and resistance. These results indicate that herbivory drives the evolution for increased tolerance, and that changes in tolerance are not linked to changes in resistance. We suggest that the simultaneous study of tolerance, attack intensity in the field and resistance constitutes a powerful tool to understand how plant strategies to avoid negative effects of herbivore damage evolve.

  10. Screening cotton genotypes for seedling drought tolerance

    Directory of Open Access Journals (Sweden)

    Penna Julio C. Viglioni

    1998-01-01

    Full Text Available The objectives of this study were to adapt a screening method previously used to assess seedling drought tolerance in cereals for use in cotton (Gossypium hirsutum L. and to identify tolerant accessions among a wide range of genotypes. Ninety genotypes were screened in seven growth chamber experiments. Fifteen-day-old seedlings were subjected to four 4-day drought cycles, and plant survival was evaluated after each cycle. Three cycles are probably the minimum required in cotton work. Significant differences (at the 0.05 level or lower among entries were obtained in four of the seven experiments. A "confirmation test" with entries previously evaluated as "tolerant" (high survival and "susceptible" (low survival was run. A number of entries duplicated their earlier performance, but others did not, which indicates the need to reevaluate selections. Germplasms considered tolerant included: `IAC-13-1', `IAC-RM4-SM5', `Minas Sertaneja', `Acala 1517E-1' and `4521'. In general, the technique is simple, though time-consuming, with practical value for screening a large number of genotypes. Results from the screening tests generally agreed with field information. The screening procedure is suitable to select tolerant accessions from among a large number of entries in germplasm collections as a preliminary step in breeding for drought tolerance. This research also demonstrated the need to characterize the internal lack of uniformity in growth chambers to allow for adequate designs of experiments.

  11. Sugars and Desiccation Tolerance in Seeds 1

    Science.gov (United States)

    Koster, Karen L.; Leopold, A. Carl

    1988-01-01

    Soluble sugars have been shown to protect liposomes and lobster microsomes from desiccation damage, and a protective role has been proposed for them in several anhydrous systems. We have studied the relationship between soluble sugar content and the loss of desiccation tolerance in the axes of germinating soybean (Glycine max L. Merr. cv Williams), pea (Pisum sativum L. cv Alaska), and corn (Zea mays L. cv Merit) axes. The loss of desiccation tolerance during imbibition was monitored by following the ability of seeds to germinate after desiccation following various periods of preimbibition and by following the rates of electrolyte leakage from dried, then rehydrated axes. Finally, we analyzed the soluble sugar contents of the axes throughout the transition from desiccation tolerance to intolerance. These analyses show that sucrose and larger oligosaccharides were consistently present during the tolerant stage, and that desiccation tolerance disappeared as the oligosaccharides were lost. The results support the idea that sucrose may serve as the principal agent of desiccation tolerance in these seeds, with the larger oligosaccharides serving to keep the sucrose from crystallizing. PMID:16666392

  12. Pavlovian conditioning analysis of morphine tolerance.

    Science.gov (United States)

    Siegel, S

    1978-01-01

    It has been demonstrated that many conditional responses to a variety of drugs are opposite in direction to the unconditional effects of the drug, and the conditioning analysis of morphine tolerance emphasizes the fact that subjects with a history of morphine administration display morphine-compensatory conditional responses when confronted with the usual administration procedure but without the drug. Thus, when the drug is presented in the context of the usual administration cues, these conditional morphine-compensatory responses would be expected to attenuate the drug-induced unconditional responses, thereby decreasing the observed response to the drug. Research has been summarized which supports this compensatory conditioning model of tolerance by demonstrating that the display of tolerance is specific to the environment in which the drug has been previously administered. Further evidence supporting this theory of tolerance has been provided by studies establishing that extinction, partial reinforcement, and latent inhibition--non-pharmacological manipulations known to be effective in generally affecting the display of conditional responses--similarly affect the display of morphine tolerance. Additional research has suggested many parallels between learning and morphine tolerance: Both processes exhibit great retention, both are disrupted by electroconvulsive shock and frontal cortical stimulation, both are retarded by inhibitors of protein synthesis, and both are facilitated by antagonists of these metabolic inhibitors.

  13. Accident-tolerant control rod

    International Nuclear Information System (INIS)

    Ohta, Hirokazu; Sawabe, Takashi; Ogata, Takanari

    2013-01-01

    Boron carbide (B 4 C) and hafnium (Hf) metal are used for the neutron absorber materials of control rods in BWRs, and silver-indium-cadmium (Ag-In-Cd) alloy is used in PWRs. These materials are clad with stainless steel. The eutectic point of B 4 C and iron (Fe) is about 1150 deg. C and the melting point of Ag-In-Cd alloy is about 800 deg. C, which are lower than the temperature of zircaloy - steam reaction increases rapidly (∼1200 deg. C). Accordingly, it is possible that the control rods melt and collapse before the reactor core is significantly damaged in the case of severe accidents. Since the neutron absorber would be separated from the fuels, there is a risk of re-criticality, when pure water or seawater is injected for emergency cooling. In order to ensure sub-criticality and extend options of emergency cooling in the course of severe accidents, a concept of accident-tolerant control rod (ACT) has been derived. ACT utilises a new absorber material having the following properties: - higher neutron absorption than current control rod; - higher melting or eutectic temperature than 1200 deg. C where rapid zircaloy oxidation occurs; - high miscibility with molten fuel materials. The candidate of a new absorber material for ATC includes gadolinia (Gd 2 O 3 ), samaria (Sm 2 O 3 ), europia (Eu 2 O 3 ), dysprosia (Dy 2 O 3 ), hafnia (HfO 2 ). The melting point of these materials and the liquefaction temperature with Fe are higher than the rapid zircaloy oxidation temperature. ACT will not collapse before the core melt-down. After the core melt-down, the absorber material will be mixed with molten fuel material. The current absorber materials, such as B 4 C, Hf and Ag-In-Cd, are charged at the tip of ATC in which the neutron flux is high, and a new absorber material is charged in the low-flux region. This design could minimise the degradation of a new absorber material by the neutron absorption and the influence of ATC deployment on reactor control procedure. As a

  14. The political limit of tolerance O limite político da tolerância

    Directory of Open Access Journals (Sweden)

    Joseph Yvon Thériault

    2008-06-01

    Full Text Available In the contemporary discussions about democracy modifications, tolerance has been frequently evoked in order to express the way by which the democracies respond to the new demands of plurality recognition. While drawing the general lines of the connection between tolerance and democracy, the present article intends to deepen the comprehension of tolerance’s places and limits inside the democracy. After that, the text should evaluate the reach of the contemporary use of tolerance. Keywords: Democracy. Tolerance. Political theory. National Identity. Nas discussões contemporâneas sobre as transformações da democracia, a tolerância é com freqüência evocada para expressar o modo pelo qual as democracias respondem às novas exigências de reconhecimento da pluralidade. Ao esboçar as linhas gerais da relação entre tolerância e democracia, o presente artigo pretende aprofundar a compreensão do lugar e dos limites da tolerância na democracia. Em um segundo momento, tratará de avaliar o alcance do uso contemporâneo da tolerância. Palavras-chave: Democracia. Tolerância. Teoria Política. Identidade Nacional.

  15. In vitro selection of induced mutants to salt-tolerance: Inducible gene regulation for salt tolerance

    Energy Technology Data Exchange (ETDEWEB)

    Winicov, I [Department of Microbiology and Biochemistry, Univ. of Nevada-Reno, Reno, NV (United States)

    1997-07-01

    A selection protocol to obtain salt tolerant calli, followed by regeneration and progeny-test of the regenerated plants for salt tolerance in rice was investigated. Callus cultures were initiated from salt-sensitive US elite rice lines and cv. `Pokkali`. Salt-tolerant cell lines were selected from these by a single step selection procedure. The selected salt-tolerant lines grew well on medium with {+-} 0.5% or 1% NaCl, while the parent lines occasionally survived, but did not grow at these salt concentrations. Plants were regenerated from these cell lines through different passages on medium containing salt. Seed was collected from the regenerated plants and salt tolerance of R2 seedlings was compared with those regenerated without salt selection. Salt-tolerance was measured by survival and productive growth of newly germinated seedlings in Hoagland solution with 0.3% and 0.5% NaCl for 4 weeks. Heritable improvement in salt tolerance was obtained in R2 seedlings from one plant regenerated after 5 months selection. Survival and growth of these seedlings was equivalent to that from `Pokkali` seedlings. These results show that cellular tolerance can provide salt-tolerance in rice plants. (author). 6 refs, 2 tabs.

  16. In vitro selection of induced mutants to salt-tolerance: Inducible gene regulation for salt tolerance

    International Nuclear Information System (INIS)

    Winicov, I.

    1997-01-01

    A selection protocol to obtain salt tolerant calli, followed by regeneration and progeny-test of the regenerated plants for salt tolerance in rice was investigated. Callus cultures were initiated from salt-sensitive US elite rice lines and cv. 'Pokkali'. Salt-tolerant cell lines were selected from these by a single step selection procedure. The selected salt-tolerant lines grew well on medium with ± 0.5% or 1% NaCl, while the parent lines occasionally survived, but did not grow at these salt concentrations. Plants were regenerated from these cell lines through different passages on medium containing salt. Seed was collected from the regenerated plants and salt tolerance of R2 seedlings was compared with those regenerated without salt selection. Salt-tolerance was measured by survival and productive growth of newly germinated seedlings in Hoagland solution with 0.3% and 0.5% NaCl for 4 weeks. Heritable improvement in salt tolerance was obtained in R2 seedlings from one plant regenerated after 5 months selection. Survival and growth of these seedlings was equivalent to that from 'Pokkali' seedlings. These results show that cellular tolerance can provide salt-tolerance in rice plants. (author). 6 refs, 2 tabs

  17. Suppressor cells in transplantation tolerance: I. analysis of the suppressor status of neonatally and adoptively tolerized rats

    International Nuclear Information System (INIS)

    Dorsch, S.; Roser, B.

    1982-01-01

    The lymphocytes from neonatally tolerant rats which adoptively transfer tolerance to sublethally irradiated recipients do so by specificallly suppressing the regeneration of alloreactivity which normally occurs after irradiation. Although tolerant cells will only partially suppress normal alloreactive cells when the two are mixed in near equivalent numbers, experiments in which the interval between injection of tolerant and normal cells into irradiated recipients was gradually extended, indicated that total suppression of normally alloreactive cells was achieved after 8 weeks of prior residence of tolerant cells in the adoptive host. Further evidence that tolerant cells would only suppress if present in excess of normal cells was obtained by reducing the tolerant cell populaton in tolerant donor rats by whole body irradiation. The persistence of tolerance through repeated adoptive transfers was correlated with the persistence of donor (chimeric) cells and the indicator skin graft on adoptive recipients only amplified tolerance expression where the inocula of tolerant cells given was weakly suppressive

  18. Salt tolerance in wheat - an overview. (abstract)

    International Nuclear Information System (INIS)

    Ashraf, M.

    2005-01-01

    Considerable efforts have been made during the past few years to overcome the problem of salinity through the development of salt tolerant lines of important crop species using screening, breeding and molecular biology techniques. In view of considerable importance of spring wheat as a major staple food crop of many countries, plant scientists have directed there attention to identify and develop salt tolerant genotypes that can be of direct use on salt-affected soils. Although considerable progress in understanding individual phenomenon and genes involved in plant response to salinity stress has been made over the past few years, underlying physiological mechanisms producing salt tolerant plants is still unclear. It has been suggested that salt tolerance of plants could be improved by defining genes or characters. Twenty years ago, it was suggested that genes located on the D genome of bread wheat confer salinity tolerance to hexaploid wheat by reducing Na/sup +/ accumulation in the leaf tissue and increasing discrimination in favour of K/sup +/. However, recently, low Na/sup +/ accumulation and high K/sup +/Na/sup +/ discrimination, of similar magnitude to bread wheat, in several selections of durum wheat has been observed, supporting the notion that salt tolerance is controlled by multiple genes, which are distributed throughout the entire set of chromosomes. In addition, various physiological selection criteria such as compatible osmolytes (glycinebetaine, proline, trehalose, mannitol etc.), antioxidants, carbon discrimination, high K/sup +//Na/sup +/ ratio etc. have been discussed. Although tolerance to salinity is known to have a multigenic inheritance, mediated by a large number of genes, knowledge of heritability and the genetic mode of salinity tolerance is still lacking because few studies have yet been conducted in these areas. Indeed, genetic information is lagging behind the physiological information. Modern methods such as recombinant DNA technology

  19. 75 FR 68214 - Flubendiamide; Pesticide Tolerances; Technical Correction

    Science.gov (United States)

    2010-11-05

    ... typographical errors in the referenced rule, specifically, to revise incorrect tolerance values for the... tolerance value for the established tolerances for corn, field, grain (0.02 ppm); corn, field, stover (0.15... field trial and processing data, these tolerance values should be revised to 0.03 ppm; 15 ppm; 25 ppm...

  20. 40 CFR 180.586 - Clothianidin; tolerances for residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Clothianidin; tolerances for residues... § 180.586 Clothianidin; tolerances for residues. (a) General. Tolerances are established for residues of the insecticide clothianidin, including its metabolites and degradates. Compliance with the tolerance...