WorldWideScience

Sample records for polishing coal synthesis

  1. Germanium content in Polish hard coals

    Directory of Open Access Journals (Sweden)

    Makowska Dorota

    2016-01-01

    Full Text Available Due to the policy of the European Union, it is necessary to search for new sources of scarce raw materials. One of these materials is germanium, listed as a critical element. This semi-metal is widely used in the electronics industry, for example in the production of semiconductors, fibre optics and solar cells. Coal and fly ash from its combustion and gasification for a long time have been considered as a potential source of many critical elements, particularly germanium. The paper presents the results of germanium content determination in the Polish hard coal. 23 coal samples of various coal ranks were analysed. The samples were collected from 15 mines of the Upper Silesian Coal Basin and from one mine of the Lublin Coal Basin. The determination of germanium content was performed with the use of Atomic Absorption Spectrometry with Electrothermal Atomization (GFAAS. The investigation showed that germanium content in the analysed samples was at least twice lower than the average content of this element in the hard coals analysed so far and was in the range of 0.08 ÷ 1.28 mg/kg. Moreover, the content of Ge in the ashes from the studied coals does not exceed 15 mg/kg, which is lower than the average value of Ge content in the coal ashes. The highest content of this element characterizes coals of the Lublin Coal Basin and young coals type 31 from the Vistula region. The results indicate a low utility of the analysed coal ashes as a source of the recovery of germanium. On the basis of the analyses, the lack of the relationship between the content of the element and the ash content in the tested coals was noted. For coals of the Upper Silesian Coal Basin, the relationship between the content of germanium in the ashes and the depth of the seam was observed.

  2. Database for content of mercury in Polish brown coal

    Science.gov (United States)

    Jastrząb, Krzysztof

    2018-01-01

    Poland is rated among the countries with largest level of mercury emission in Europe. According to information provided by the National Centre for Balancing and Management of Emissions (KOBiZE) more than 10.5 tons of mercury and its compounds were emitted into the atmosphere in 2015 from the area of Poland. Within the scope of the BazaHg project lasting from 2014 to 2015 and co-financed from the National Centre of Research and Development (NCBiR) a database was set up with specification of mercury content in Polish hard steam coal, coking coal and brown coal (lignite) grades. With regard to domestic brown coal the database comprises information on coal grades from Brown Coal Mines of `Bełchatów', `Adamów', `Turów' and `Sieniawa'. Currently the database contains 130 records with parameters of brown coal, where each record stands for technical analysis (content of moisture, ash and volatile particles), elemental analysis (CHNS), content of chlorine and mercury as well as net calorific value and combustion heat. Content of mercury in samples of brown coal grades under test ranged from 44 to 985 μg of Hg/kg with the average level of 345 μg of Hg/kg. The established database makes up a reliable and trustworthy source of information about content of mercury in Polish fossils. The foregoing details completed with information about consumption of coal by individual electric power stations and multiplied by appropriate emission coefficients may serve as the background to establish loads of mercury emitted into atmosphere from individual stations and by the entire sector of power engineering in total. It will also enable Polish central organizations and individual business entities to implement reasonable policy with respect of mercury emission into atmosphere.

  3. Unattached fraction of radon progeny in Polish coal mines

    International Nuclear Information System (INIS)

    Skubacz, K.; Michalik, B.

    2002-01-01

    The system of the monitoring of the radiation hazard in Polish coal mines is based on the monitoring of the workplaces. This system works since 1989 in all coal mines. It gives a very good basis for further epidemiological investigation and assessment of the health detriment within the population of the mines as a result of the exposure for natural radiation. It is very important problem, due to the fact of the presence in the mines another factors, which probably have a synergetic effects on the respiratory tracts. As the routine instrument, a device called ALFA-31 sampling probe was developed in our laboratory. This device was accomplished to regular dust sampler and simultaneous measurements of dust content and potential alpha energy concentration of radon progeny are obligatory in all underground mines in Poland. But the microcyclone used a separator of the respirable fraction which causes the cut-off of unattached fraction of radon progeny, On the other hand measurements of the unattached fraction of short lived radon progeny play a very important role in the investigations of the adequate dose from this source of radiation hazard. During field experiments the use of the alpha spectroscopy system is necessary, while measurements are done not in the vacuum chambers but under normal pressure. It leads to situation, when particular peaks in alpha spectrum are very wide and interfere with other peaks of another alpha-emitting radionuclides. Such instrumentation was designed and completed, and a survey in several underground mines was performed. The analysis of the obtained results must be done very carefully; in other case it may cause a very big uncertainty of the result. In this paper a new approach to the analysis of the alpha spectra has been described. This approach can be used also in other applications of alpha spectroscopy, in which the analysis of energy of alpha peaks in spectrum is needed. The method of the analysis is based on a non-linear regression

  4. The role of Polish coal in the EU economy; Die Bedeutung der polnischen Steinkohle fuer die Wirtschaft der Europaeischen Union

    Energy Technology Data Exchange (ETDEWEB)

    Czaja, P. [AGH Univ. fuer Wissenschaft und Technologie, Krakau (Poland)

    2006-06-15

    The contribution attempts a comparative assessment of coal mining in Poland and other EU member states. The importance of Polish coal is reflected in the share of Polish coal in EU imports, its contribution to the EU internal market and the total coal consumption within the EU. The role of coal in Poland will be maintained for the next 30 years or so, although the share of other energy sources should increase in the long run. (orig.)

  5. Cost comparison of selected US and Polish coal mines, August 1993

    International Nuclear Information System (INIS)

    1993-08-01

    This report on the Polish coal industry is the fifth in a series of studies on coal exporting countries requested by the House Appropriations Committee. The committee requested that the basic differences in mining costs for U.S. and foreign mines be identified, especially those costs incurred in complying with health, safety, and environmental regulations. Basic costs in extracting raw coal are analyzed in this report for underground longwall mining operations, the only mining method employed in Poland for hard coal. In this report there is also a limited analysis of the relative market competitiveness of selected Polish and U.S. steam and metallurgical coal mines in the European electric utility and metallurgical coal markets

  6. Separation of mercury in industrial processes of Polish hard steam coals cleaning

    Directory of Open Access Journals (Sweden)

    Wierzchowski Krzysztof

    2016-01-01

    Full Text Available Coal use is regarded as one of main sources of anthropogenic propagation of mercury in the environment. The coal cleaning is listed among methods of the mercury emission reduction. The article concerns the statistical assessment of mercury separation between coal cleaning products. Two industrial processes employed in the Polish coal preparation plants are analysed: coal cleaning in heavy media vessels and coal cleaning in jigs. It was found that the arithmetic mean mercury content in coarse and medium coal size fractions for clean coal from heavy media vessels, amounts 68.9 μg/kg, and most of the results lay below the mean value, while for rejects it amounts 95.5 μg/kg. It means that it is for around 25 μg/kg greater than in the clean coal. The arithmetic mean mercury content in raw coal smalls amounts around 118 mg/kg. The cleaning of smalls in jigs results in clean coal and steam coal blends characterized by mean mercury content 96.8 μg/kg and rejects with mean mercury content 184.5 μg/kg.

  7. The prospects for hard coal as a fuel for the Polish power sector

    International Nuclear Information System (INIS)

    Kaminski, Jacek; KudeLko, Mariusz

    2010-01-01

    This paper presents the prospects for the development of the Polish hard coal sector from the perspective of the power sector. The most important issues determining the mid- and long-term future for domestic coal production are: (1) the development of the economy, hence the demand for electricity, (2) regulations (mostly environmental) affecting the power sector, (3) the competitiveness of coal-based technologies, and (4) the costs of domestic coal production. Since the range of issues and relations being considered is very broad, a specific method needs to be employed for the quantitative analysis. The tool applied in this study is the partial equilibrium model POWER-POL, in which both the coal and the power sectors are incorporated. The model focuses on energy-economy-environmental issues without capturing detailed macroeconomic links. The model was run under six scenario assumptions. The results show that the domestic coal sector should maintain its position as a key supplier of primary energy for the Polish power sector. However, the environmental regulations to which the domestic power sector has to conform will decrease the share of coal in the fuel-mix. Since the investment processes in this sector are usually long-term, the effects of changes will be noticeable from 2015 onwards. - Research highlights: →Application of the partial equilibrium model POWER-POL for a quantitative analysis. →Coal will maintain its dominant position in the Polish heat and electricity production fuel-mix at least up to 2020. →Attractiveness of domestic hard coal supplies will depend on the environmental regulations (mostly on the EU level) and development in the world coal market. →The first nuclear power plant will be put into operation in 2020.

  8. The role of coal consumption in the economic growth of the Polish economy in transition

    International Nuclear Information System (INIS)

    Gurgul, Henryk; Lach, Lukasz

    2011-01-01

    The main goal of this paper is an analysis of the causal links between quarterly coal consumption in the Polish economy and GDP. For the sake of accurate computation an additional variable - employment - was also taken into account. Computations conducted for the period Q1 2000 to Q4 2009 by means of recent causality techniques confirmed the neutrality of hard coal usage with respect to economic growth. On the other hand, calculations for the pairs lignite-GDP and total coal consumption-GDP showed the existence of a significant nonlinear causality from coal usage to economic growth. This is clear evidence for claiming that lignite plays an important role in the economic growth of the Polish economy. Furthermore, each coal-related variable was found to have a nonlinear causal impact on employment. Because of the relatively short length of available time series we additionally applied bootstrap critical values. The empirical results computed by both methods did not exhibit significant differences. These results have important policy implications. In general, our findings support the hypothesis that closing hard coal mines in Poland should have no significant repercussions on economic growth. However, this does not seem to be true for lignite mines. - Research highlights: → The reduction of hard coal consumption should not hamper economic growth in Poland. → Lignite consumption is an important factor determining economic growth in Poland. → The usage of lignite and hard coal has a causal impact on employment in Poland.

  9. The potential risk of environmental contamination by mercury contained in Polish coal mining waste

    Directory of Open Access Journals (Sweden)

    Tomasz Antoszczyszyn

    2016-01-01

    Full Text Available The paper contains reference literature analysis concerning mercury content in Polish bituminous coal and post-mining waste as well as the impact of mercury content on the environment. The aim of the paper was to determine the occurrence of the risk of contamination of the environment with mercury compounds found in demolition bituminous coal landfills. Mercury, due to its toxic properties has been classified among the most dangerous substances to human health. There are three groups of sources of mercury release into the environment: natural, anthropogenic and remission. Coal mining, its processing and use in the energy sector has the greatest relevance regarding the pollution of the environment with mercury compounds in Poland. A review of reference literature shows that the average content of mercury in Polish bituminous coal varies within a wide range of 41–399 ppb, which is conditional on the origin, age and type of coal. The production of coal has led to a number of facilities in the form of structurally and age-varied landfills, heaps and mining waste dumps. The content of mercury in post-mining waste is in the range from approximately 55 to 380 ppb. The problem of environmental contamination with mercury has attracted considerable interest due to the effects that its concentration have in the biosphere. On the basis of the existing data it has been found that the content of mercury in soils in areas degraded by mining and processing of coal is even 10–16 times higher, compared to the geochemical background. It is necessary to conduct research in this area due to the limited results of research on mercury content in deposited waste from the preparation and flotation of Polish bituminous coals and the potential harmful effect of mercury on the environment. The paper is dedicated to the mercury content in waste from the extraction and processing of bituminous coal.

  10. Analysis of operational risk in a Polish coal preparation plant

    Energy Technology Data Exchange (ETDEWEB)

    Cieslak, W.; Sablik, J.; Martyniak, J.; Wycisk, H. [Central Mining Institute, Katowice (Poland)

    2001-07-01

    The article presents methodology and results of studies, which allow one to characterise a coal preparation plant by means of operational risk analysis and to draw conclusions which could be used for making production management and investment decisions. 6 refs., 6 figs., 2 tabs.

  11. Characterizing thermogenic coalbed gas from Polish coals of different ranks by hydrous pyrolysis

    Science.gov (United States)

    Kotarba, M.J.; Lewan, M.D.

    2004-01-01

    To provide a better characterization of origin and volume of thermogenic gas generation from coals, hydrous pyrolysis experiments were conducted at 360??C for 72 h on Polish coals ranging in rank from lignite (0.3% R r) to semi-anthracite (2.0% Rr). Under these conditions, the lignites attained a medium-volatile bituminous rank (1.5% Rr), high-volatile bituminous coals attained a low-volatile bituminous rank (1.7% Rr), and the semi-anthracite obtained an anthracite rank (4.0% R r). Hydrous pyrolysis of a coal, irrespective of rank, provides a diagnostic ??13C value for its thermogenic hydrocarbon gases. This value can be used quantitatively to interpret mixing of indigenous thermogenic gas with microbial methane or exogenous thermogenic gas from other sources. Thermogenic methane quantities range from 20 dm3/kg of lignite (0.3% Rr) to 0.35 dm3/kg of semi-anthracite (2.0% Rr). At a vitrinite reflectance of 1.7% Rr, approximately 75% of the maximum potential for a coal to generate thermogenic methane has been expended. At a vitrinite reflectance of 1.7% Rr, more than 90% of the maximum potential for a coal to generate CO2 has been expended. Assuming that these quantities of generated CO2 remain associated with a sourcing coal bed as uplift or erosion provide conditions conducive for microbial methanogenesis, the resulting quantities of microbial methane generated by complete CO2 reduction can exceed the quantities of thermogenic methane generated from the same coal bed by a factor of 2-5. ?? 2004 Elsevier Ltd. All rights reserved.

  12. Lab-Scale Investigations During Combustion of Agricultural Residues and Selected Polish Coals

    Directory of Open Access Journals (Sweden)

    Kordylewski Włodzimierz K.

    2014-06-01

    Full Text Available Preliminary lab-scale investigations were conducted on slagging abatement in biomass-firing by fuel mixing. Three agriculture biomass fuels and olive cake were used in the experiments. Polish lignites and bituminous coals were examined as anti-sintering additives. The effects of chlorine release, potassium retention and ash sintering were examined by heating samples of biomass fuels and additives in the muffle oven and, next, firing them in the laboratory down-fired furnace at the temperature in the range of 800-1150ºC. The obtained slag samples were analysed on: chlorine and potassium content, sintering tendency and crystalline components. Among the examined coals lignite from Turów mine and bituminous coal from Bolesław Śmiały mine appeared to be the most effective in potassium retention in aluminosilicate and chlorine release from slag. Possibly the major factor of these coals which reduced ash sintering was relatively high content of kaolinite

  13. Carbon Nanotube Synthesis Using Coal Pyrolysis.

    Science.gov (United States)

    Moothi, Kapil; Simate, Geoffrey S; Falcon, Rosemary; Iyuke, Sunny E; Meyyappan, M

    2015-09-01

    This study investigates carbon nanotube (CNT) production from coal pyrolysis wherein the output gases are used in a chemical vapor deposition reactor. The carbon products are similar to those using commercial coal gas as feedstock, but coal is a relatively cheaper feedstock compared to high purity source gases. A Gibbs minimization model has been developed to predict the volume percentages of product gases from coal pyrolysis. Methane and carbon monoxide were the largest carbon components of the product stream and thus formed the primary source for CNT synthesis. Both the model and the observations showed that increasing the furnace temperature led to a decrease in the absolute quantities of "useful" product gases, with the optimal temperature between 400 and 500 °C. Based on the experimental data, a kinetic rate law for CNT from coal pyrolysis was derived as d[CNT]/dt = K([CO][CH4])(1/2), where K is a function of several equilibrium constants representing various reactions in the CNT formation process.

  14. Application of stable environmental isotopes in mine hydrogeology taking Polish coal basins as an example

    International Nuclear Information System (INIS)

    Rozkowski, A.; Przewlocki, K.

    1974-01-01

    Preliminary results of the stable isotope investigations carried out in Polish coal basins are presented. In the case of the Lublin Coal Basin, the extreme values of δ 18 O lie between -10.05 and -4.95 per mille, and of δD from -71. 99 to -41.40 per mille. The tested waters may be divided into two groups regarding the relative isotope content. The first group includes waters with overall mineralization lying between 0.4 and 2.5 g/litre. All the waters from the overburden may be placed in this group, and also most of those from the productive Carboniferous. The low content of heavy isotopes allows this group to be classified as infiltration waters. Hence it must be expected that water inflows to the mines will come from both static and dynamic sources. Waters from the Carboniferous with mineralization higher than 10 g/litre are grouped separately. On the precipitation line these points are shifted to the SMOW values. These waters represent a mixture of relict and infiltration waters. If mining is taken to a depth greater than 1000 m, only a minimal proportion of waters from the dynamic sources in mine inflows need be expected. In the case of the Upper Silesian Coal Basin, extreme values of δ 18 O vary from -11.57 to +0.34 per mille, and δD from -72.9 to -1.2 per mille. From analysis of the diagram showing the relation between δ 18 O and δD contents the deep infiltration of contemporary atmospheric waters in the productive Carboniferous of the northern, hydrogeologically non-isolated sector of the Coal Basin is evident. In the southern isolated sector of the basin no recent freshening of the waters under Tertiary overburden is observed. In the formations of varied geological age occurring below 600 m, relict waters appear. It may therefore be predicted that inflow to new mines scheduled for construction will be from static resources only. (author)

  15. Application of multiple sorption model to estimation of CO2 sequestration capacity or CH4 recovery in polish hard coals

    Directory of Open Access Journals (Sweden)

    Jodłowski Grzegorz

    2017-01-01

    Full Text Available The aim of the study is to estimate the theoretical capacity of coal deposits in terms of carbon dioxide storage and methane recovery estimate during the injection of carbon dioxide. The Multiple Sorption Model was used for this purpose. The range of sorption measurement data on which the simulations were based does not exceed the critical point for both methane and carbon dioxide. The model allows to calculate absorption, adsorption, expansion and total theoretical sorption. For further consideration absorption was used as the process of the percolation of the gas in the bulk of the coal matter as well as the total theoretical sorption, the occurrence of which is possible due to the presence of fractures in the coal seam. Calculated levels of absorption and the total theoretical adsorption were applied to estimate the possible storage capacity of carbon dioxide based on the data associated with the content of coal in the mining fields of individual Polish coal mines. Moreover, MSM development for the gas mixture sorption can be used to roughly assess the recovery of methane naturally occurring in coal deposits during such a process.

  16. Comparison of Methane Control Methods in Polish and Vietnamese Coal Mines

    OpenAIRE

    Borowski Marek; Kuczera Zbigniew

    2018-01-01

    Methane hazard often occurs in hard coal mines and causes very serious accidents and can be the reason of methane or methane and coal dust explosions. History of coal mining shows that methane released from the rock mass to the longwall area was responsible for numerous mining disasters. The main source of methane are coal deposits because it is autochthonous gas and is closely related with carbonification and forming of coal deposits. Degree of methane saturation in coal deposits depends on ...

  17. SYNTHESIS OF METHACRYLATES FROM COAL-DERIVED SYNGAS

    Energy Technology Data Exchange (ETDEWEB)

    Jang, B.W.L.; Spivey, J.J.; Gogate, M.R.; Zoeller, J.R.; Colberg, R.D.; Choi, G.N.

    1999-12-01

    Research Triangle Institute (RTI), Eastman Chemical Company, and Bechtel have developed a novel process for synthesis of methyl methacrylate (MMA) from coal-derived syngas, under a contract from the US Department of Energy/Fossil Energy Technology Center (DOE/FETC). This project has resulted in five US patents (four already published and one pending publication). It has served as the basis for the technical and economic assessment of the production of this high-volume intermediate from coal-derived synthesis gas. The three-step process consists of the synthesis of a propionate from ethylene carbonylation using coal-derived CO, condensation of the propionate with formaldehyde to form methacrylic acid (MAA); and esterification of MAA with methanol to yield MMA. The first two steps, propionate synthesis and condensation catalysis, are the key technical challenges and the focus of the research presented here.

  18. Contamination of settling ponds and rivers as a result of discharge of radium-bearing waters from Polish coal mines.

    Science.gov (United States)

    Chalupnik, S; Michalik, B; Wysocka, M; Skubacz, K; Mielnikow, A

    2001-01-01

    Saline waters from underground coal mines in Poland often contain natural radioactive isotopes, mainly 226Ra from the uranium decay series and 228Ra from the thorium series. Approximately 40% of the total amount of radium remains underground as radioactive deposits, but 225 MBq of 226Ra and 400 MBq of 228Ra are released daily into the rivers along with the other mine effluents from all Polish coal mines. Technical measures such as inducing the precipitation of radium in gobs, decreasing the amount of meteoric inflow water into underground workings, etc. have been undertaken in several coal mines, and as a result of these measures, the total amount of radium released to the surface waters has diminished by about 60% during the last 5-6 years. Mine water can have a severe impact on the natural environment, mainly due to its salinity. However, associated high levels of radium concentration in river waters, bottom sediments and vegetation have also been observed. Sometimes radium concentrations in rivers exceed 0.7 kBq/m3, which is the permitted level for waste waters under Polish law. The extensive investigations described here were carried out for all coal mines and on this basis the total radium balance in the effluents has been calculated. Measurements in the vicinity of mine settling ponds and in rivers have given us an opportunity to study radium behaviour in river waters and to assess the degree of contamination. Solid waste materials with enhanced natural radioactivity have been produced in huge amounts in the power and coal industries in Poland. As a result of the combustion of coal in power plants, low-radioactive waste materials are produced, with 226Ra concentration seldom exceeding a few hundreds of Bq/kg. A different situation is observed in coal mines, where, as a result of precipitation of radium from radium-bearing waters, highly radioactive deposits are formed. Sometimes the radioactivity of such materials is extremely high; precipitates from coal

  19. Planning for reliable coal quality delivery considering geological variability : A case study in polish lignite mining

    NARCIS (Netherlands)

    Naworyta, W.; Sypniowski, S.; Benndorf, J.

    2015-01-01

    The aim of coal quality control in coal mines is to supply power plants daily with extracted raw material within certain coal quality constraints. On the example of a selected part of a lignite deposit, the problem of quality control for the runof-mine lignite stream is discussed. The main goal is

  20. Comparison of Methane Control Methods in Polish and Vietnamese Coal Mines

    Directory of Open Access Journals (Sweden)

    Borowski Marek

    2018-01-01

    Full Text Available Methane hazard often occurs in hard coal mines and causes very serious accidents and can be the reason of methane or methane and coal dust explosions. History of coal mining shows that methane released from the rock mass to the longwall area was responsible for numerous mining disasters. The main source of methane are coal deposits because it is autochthonous gas and is closely related with carbonification and forming of coal deposits. Degree of methane saturation in coal deposits depends on numerous factors; mainly on presence or lack of insulating layers in cover deposit that allow or do not on degasification and easily methane outflow into surroundings. Hence in coal mining there are coal deposits that contain only low degree of methane saturation in places where is lack of insulating layers till high in methane coal deposits occurring in insulating claystones or in shales. Conducting mining works in coal deposits of high methane hazard without using of special measures to combat (ventilation, methane drainage could be impossible. Control of methane hazard depends also on other co-occuring natural dangers for which used preventive actions eliminate methane hazard. Safety in mines excavating coal deposits saturated with methane depends on the correct estimation of methane hazard, drawn up forecasts, conducted observations, hazard control as well as undertaken prevention measures. Methane risk prevention includes identification and control methods of methane hazards as well as means of combating the explosive accumulation of methane in longwall workings. The main preventive actions in underground coal mines are: effective ventilation that prevents forming of methane fuses or placed methane accumulation in headings ventilated by airflow created by main fans and in headings with auxiliary ventilation, methane drainage using drain holes that are drilled from underground headings or from the surface, methanometry control of methane concentration in

  1. Comparison of Methane Control Methods in Polish and Vietnamese Coal Mines

    Science.gov (United States)

    Borowski, Marek; Kuczera, Zbigniew

    2018-03-01

    Methane hazard often occurs in hard coal mines and causes very serious accidents and can be the reason of methane or methane and coal dust explosions. History of coal mining shows that methane released from the rock mass to the longwall area was responsible for numerous mining disasters. The main source of methane are coal deposits because it is autochthonous gas and is closely related with carbonification and forming of coal deposits. Degree of methane saturation in coal deposits depends on numerous factors; mainly on presence or lack of insulating layers in cover deposit that allow or do not on degasification and easily methane outflow into surroundings. Hence in coal mining there are coal deposits that contain only low degree of methane saturation in places where is lack of insulating layers till high in methane coal deposits occurring in insulating claystones or in shales. Conducting mining works in coal deposits of high methane hazard without using of special measures to combat (ventilation, methane drainage) could be impossible. Control of methane hazard depends also on other co-occuring natural dangers for which used preventive actions eliminate methane hazard. Safety in mines excavating coal deposits saturated with methane depends on the correct estimation of methane hazard, drawn up forecasts, conducted observations, hazard control as well as undertaken prevention measures. Methane risk prevention includes identification and control methods of methane hazards as well as means of combating the explosive accumulation of methane in longwall workings. The main preventive actions in underground coal mines are: effective ventilation that prevents forming of methane fuses or placed methane accumulation in headings ventilated by airflow created by main fans and in headings with auxiliary ventilation, methane drainage using drain holes that are drilled from underground headings or from the surface, methanometry control of methane concentration in the air; location

  2. The impact of the structural features of the rock mass on seismicity in Polish coal mines

    Science.gov (United States)

    Patyńska, Renata

    2017-11-01

    The article presents seismic activity induced in the coal mines of the Upper Silesian Coal Basin (GZW) in relation to the locations of the occurrence of rockbursts. The comparison of these measurements with the structural features of the rock mass of coal mines indicates the possibility of estimating the so-called Unitary Energy Expenditure (UEE) in a specific time. The obtained values of UEE were compared with the distribution of seismic activity in GZW mines. The level of seismic activity in the analysed period changed and depended on the intensity of mining works and diverse mining and geological conditions. Five regions, where tremors occurred (Bytom Trough, Main Saddle, Main Trough, Kazimierz Trough, and Jejkowice and Chwałowice Trough) which belong to various structural units of the Upper Silesia were analyzed. It was found out that rock bursts were recorded only in three regions: Main Saddle, Bytom Trough, and Jejkowice and Chwałowice Trough.

  3. CO2-ECBM and CO2 Sequestration in Polish Coal Seam – Experimental Study

    Directory of Open Access Journals (Sweden)

    Paweł Baran

    2014-01-01

    Originality/value: The results indicate successful sorption of carbon dioxide in each experiment. This provides the rationale to study the application of the coal tested to obtain methane genetic origin genetic methane with the use of the CO2 injection.

  4. Preliminary results of measurements of unattached fraction of radon progeny in Polish coal mines

    International Nuclear Information System (INIS)

    Skubacz, K.; Lebecka, J.; Michalik, B.; Reineking, A.

    1996-01-01

    The aim of this work was better recognizing and understanding of the radiation exposure of miners in underground coal mines. Within the project supported by EC we have built an equipment for measurements of unattached fraction of radon daughters. We performed measurements of unattached fraction of radon daughters in two chosen mines using the built equipment. Preliminary results of measurements performed in 14 place in two mines show that in some places the unattached fraction of radon progeny is higher than 5% known from literature. These results also indicate, that it seems to be a relation between the concentration of unattached fraction and between the humidity of air and respirable dust concentration. (author)

  5. Synthesis of high ion exchange zeolites from coal fly ash

    Energy Technology Data Exchange (ETDEWEB)

    Querol, X.; Moreno, N.; Alastuey, A.; Juan, R.; Andres, J.M.; Lopez-Soler, A.; Ayora, C.; Medinaceli, A.; Valero, A. [CSIC, Barcelona (Spain)

    2007-07-01

    This study focuses on the synthesis at a pilot plant scale of zeolitic material obtained from the coal fly ashes of the Teruel and Narcea power plants in Spain. After the optimisation of the synthesis parameters at laboratory scale, the Teruel and Narcea fly ashes were selected as low and high glass fly ashes. The pilot plant scale experiments were carried out in a 10 m{sup 3} reactor of Clariant SA (Barcelona, Spain). The results allowed obtaining 1.1 and 2.2 tonnes of zeolitic material with 40 and 55% of NaP1 content, in two single batch experiments of 24 and 8 hours, for Teruel and Narcea fly ashes, respectively. The cation exchange capacities (CEC) of the final product reached 2.0 and 2.7 meq g{sup -1} for Teruel and Narcea zeolitic material, respectively, which are very close to the usual values reached by the high quality natural zeolitic products. Finally, with the aim of testing possible applications of the commercial NaP1-IQE and pilot plant NaP1-Narcea zeolitic products in water decontamination, efficiency for metal uptake from waste waters from electroplating baths was investigated.

  6. Biological upgrading of coal-derived synthesis gas: Final report

    Energy Technology Data Exchange (ETDEWEB)

    Barik, S.; Johnson, E.R.; Ko, C.W.; Clausen, E.C.; Gaddy, J.L.

    1986-10-01

    The technical feasibility of the biological conversion of coal synthesis gas to methane has been demonstrated in the University of Arkansas laboratories. Cultures of microorganisms have been developed which achieve total conversion in the water gas shift and methanation reactions in either mixed or pure cultures. These cultures carry out these conversions at ordinary temperatures and pressures, without sulfur toxicity. Several microorganisms have been identified as having commercial potential for producing methane. These include a mixed culture of unidentified bacteria; P. productus which produces acetate, a methane precursor; and Methanothrix sp., which produces methane from acetate. These cultures have been used in mixed reactors and immobilized cell reactors to achieve total CO and H/sub 2/ conversion in a retention time of less than two hours, quite good for a biological reactor. Preliminary economic projections indicate that a biological methanation plant with a size of 5 x 10/sup 10/ Btu/day can be economically attractive. 42 refs., 26 figs., 86 tabs.

  7. Bioconversion of coal derived synthesis gas to liquid fuels

    Science.gov (United States)

    Jain, M. K.; Worden, R. M.; Grethlein, A.

    1994-07-01

    The overall objective of the project is to develop an integrated two-stage fermentation process for conversion of coal-derived synthesis gas to a mixture of alcohols. This is achieved in two steps. In the first step, Butyribacterium methylotrophicum converts carbon monoxide (CO) to butyric and acetic acids. Subsequent fermentation of the acids by Clostridium acetobutylicum leads to the production of butanol and ethanol. The tasks for this quarter were: development/isolation of superior strains for fermentation of syngas; evaluation of bioreactor configuration for improved mass transfer of syngas; recovery of carbon and electrons from H2-CO2; initiation of pervaporation for recovery of solvents; and selection of solid support material for trickle-bed fermentation. Technical progress included the following: butyrate production was enhanced during H2/CO2 (50/50) batch fermentation; isolation of CO-utilizing anaerobic strains is in progress; pressure (15 psig) fermentation was evaluated as a means of increasing CO availability; polyurethane foam packing material was selected for trickle bed solid support; cell recycle fermentation on syngas operated for 3 months. Acetate was the primary product at pH 6.8; trickle bed and gas lift fermentor designs were modified after initial water testing; and pervaporation system was constructed (No alcohol selectivity was shown with the existing membranes during initial start-up).

  8. Coal

    International Nuclear Information System (INIS)

    Muir, D.A.

    1991-01-01

    The international coal market trends are outlined and the place of Australian coal industry is discussed. It is shown that while the world supply and demand for coal has begun to tighten, the demand for coal is expected to remain strong in both Asia and Europe. Consequently, in 1991-1992 Australian black coal production and export returns are forecast to rise by 4% and 7% respectively. 1 fig

  9. Phase transformations in synthesis technologies and sorption properties of zeolites from coal fly ash

    Directory of Open Access Journals (Sweden)

    О. Б. Котова

    2016-08-01

    Full Text Available Coal fly ash is generated in the course of combustion of coal at thermal power plants. Environmental problems increase sharply without disposing that industrial waste. Technologies were tested of hydrothermal synthesis of zeolites from fly ash forming during combustion of coal at thermal power plants of the Pechora coal basin and dependences were identified of the experiment conditions on physical and chemical properties of the end product. It is demonstrated that synthesizing zeolites from fly ash is the first stage of forming ceramic materials (ceramic membranes, which defines the fundamental character (importance of that area of studies. It was for the first time that sorption and structural characteristics and cation-exchange properties of fly ash from the Pechora basin coals were studied with respect to, Ba2+ and Sr2+.

  10. Liquefaction and desulfurization of coal using synthesis gas

    Science.gov (United States)

    Fu, Yuan C.

    1977-03-08

    A process for desulfurizing and liquefying coal by heating said coal at a temperature of 375.degree.-475.degree. C in the presence of a slurry liquid, hydrogen, carbon monoxide, steam, and a catalyst comprising a desulfurization catalyst and an alkali metal salt.

  11. Coal

    International Nuclear Information System (INIS)

    Teissie, J.; Bourgogne, D. de; Bautin, F.

    2001-12-01

    Coal world production represents 3.5 billions of tons, plus 900 millions of tons of lignite. 50% of coal is used for power generation, 16% by steel making industry, 5% by cement plants, and 29% for space heating and by other industries like carbo-chemistry. Coal reserves are enormous, about 1000 billions of tons (i.e. 250 years of consumption with the present day rate) but their exploitation will be in competition with less costly and less polluting energy sources. This documents treats of all aspects of coal: origin, composition, calorific value, classification, resources, reserves, production, international trade, sectoral consumption, cost, retail price, safety aspects of coal mining, environmental impacts (solid and gaseous effluents), different technologies of coal-fired power plants and their relative efficiency, alternative solutions for the recovery of coal energy (fuel cells, liquefaction). (J.S.)

  12. Synthesis of hydrocarbons using coal and nuclear process heat

    International Nuclear Information System (INIS)

    Eickhoff, H.G.; Kugeler, K.

    1975-01-01

    An analysis of the global petroleum resources and demand shows that the amount of mineral oil products is sufficient to meet the requirements of the next decades. The geographical resources, however, could lead to problems of distribution and foreign exchange. The production of hydrocarbons with coal as basis using high temperature nuclear process heat has advantages compared to the conventional techniques. Next to the conservation of reserve fossil primary energy carriers there are advantages as regards prices, which at high coal costs are especially pronounced. (orig.) [de

  13. Coal

    International Nuclear Information System (INIS)

    Muir, D.A.

    1991-01-01

    It is estimated that World coal trade remained strong during the second quarter of 1991, with contributing factors including unseasonally large shipments to Japan for power generation, sustained Japanese steel production at around 112 Mt and some buildup in stocks in that country. Purchases by North Asian and European consumers also remained high. At the same time Soviet output and exports declined because of strikes and political unrest. In addition, exportable supplies in Poland fell. As a result the demand for Indonesian coal increased, and Australia exported larger than previously expected quantities of coal. ills

  14. Potential for Coal-to-Liquids Conversion in the United States-Fischer-Tropsch Synthesis

    International Nuclear Information System (INIS)

    Patzek, Tad W.; Croft, Gregory D.

    2009-01-01

    The United States has the world's largest coal reserves and Montana the highest potential for mega-mine development. Consequently, a large-scale effort to convert coal to liquids (CTL) has been proposed to create a major source of domestic transportation fuels from coal, and some prominent Montanans want to be at the center of that effort. We calculate that the energy efficiency of the best existing Fischer-Tropsch (FT) process applied to average coal in Montana is less than 1/2 of the corresponding efficiency of an average crude oil refining process. The resulting CO 2 emissions are 20 times (2000%) higher for CTL than for conventional petroleum products. One barrel of the FT fuel requires roughly 800 kg of coal and 800 kg of water. The minimum energy cost of subsurface CO 2 sequestration would be at least 40% of the FT fuel energy, essentially halving energy efficiency of the process. We argue therefore that CTL conversion is not the most valuable use for the coal, nor will it ever be, as long as it is economical to use natural gas for electric power generation. This finding results from the low efficiency inherent in FT synthesis, and is independent of the monumental FT plant construction costs, mine construction costs, acute lack of water, and the associated environmental impacts for Montana

  15. Novel nanodispersed coal liquefaction catalysts: Molecular design via microemulsion-based synthesis. Final technical report, October 1990--December 1994

    Energy Technology Data Exchange (ETDEWEB)

    Osseo-Asare, K.; Boakye, E.; Vittal, M. [and others

    1995-04-01

    This report described the synthesis of Molybdenum Sulfides in microemulsions by acidification of ammonium tetrathiomolybdate. Molybdenum Sulfides have been shown to be potential coal liquefaction catalysts. The importance of particle size, temperature effects, and coal surface chemistry to impregnation are discussed.

  16. High Yield Synthesis of Aspect Ratio Controlled Graphenic Materials from Anthracite Coal in Supercritical Fluids.

    Science.gov (United States)

    Sasikala, Suchithra Padmajan; Henry, Lucile; Yesilbag Tonga, Gulen; Huang, Kai; Das, Riddha; Giroire, Baptiste; Marre, Samuel; Rotello, Vincent M; Penicaud, Alain; Poulin, Philippe; Aymonier, Cyril

    2016-05-24

    This paper rationalizes the green and scalable synthesis of graphenic materials of different aspect ratios using anthracite coal as a single source material under different supercritical environments. Single layer, monodisperse graphene oxide quantum dots (GQDs) are obtained at high yield (55 wt %) from anthracite coal in supercritical water. The obtained GQDs are ∼3 nm in lateral size and display a high fluorescence quantum yield of 28%. They show high cell viability and are readily used for imaging cancer cells. In an analogous experiment, high aspect ratio graphenic materials with ribbon-like morphology (GRs) are synthesized from the same source material in supercritical ethanol at a yield of 6.4 wt %. A thin film of GRs with 68% transparency shows a surface resistance of 9.3 kΩ/sq. This is apparently the demonstration of anthracite coal as a source for electrically conductive graphenic materials.

  17. Synthesis of geopolymer from biomass-coal ash blends

    Science.gov (United States)

    Samadhi, Tjokorde Walmiki; Wulandari, Winny; Prasetyo, Muhammad Iqbal; Fernando, Muhammad Rizki; Purbasari, Aprilina

    2017-09-01

    Geopolymer is an environmentally attractive Portland cement substitute, owing to its lower carbon footprint and its ability to consume various aluminosilicate waste materials as its precursors. This work describes the development of geopolymer formulation based on biomass-coal ash blends, which is predicted to be the prevalent type of waste when biomass-based thermal energy production becomes mainstream in Indonesia. The ash blends contain an ASTM Class F coal fly ash (FA), rice husk ash (RHA), and coconut shell ash (CSA). A mixture of Na2SiO3 and concentrated KOH is used as the activator solution. A preliminary experiment identified the appropriate activator/ash mass ratio to be 2.0, while the activator Na2SiO3/KOH ratio varies from 0.8 to 2.0 with increasing ash blend Si/Al ratio. Both non-blended FA and CSA are able to produce geopolymer mortars with 7-day compressive strength exceeding the Indonesian national SNI 15-2049-2004 standard minimum value of 2.0 MPa stipulated for Portland cement mortars. Ash blends have to be formulated with a maximum RHA content of approximately 50 %-mass to yield satisfactory 7-day strength. No optimum ash blend composition is identified within the simplex ternary ash blend compositional region. The strength decreases with Si/Al ratio of the ash blends due to increasing amount of unreacted silicate raw materials at the end of the geopolymer hardening period. Overall, it is confirmed that CSA and blended RHA are feasible raw materials for geopolymer production..

  18. Synthesis of acrylates and methacrylates from coal-derived syngas

    Energy Technology Data Exchange (ETDEWEB)

    Spivey, J.J.; Gogate, M.R.; Jang, B.W.L. [Bechtel, San Francisco, CA (United States)] [and others

    1995-12-31

    Acrylates and methacrylates are among the most widely used chemical intermediates in the world. One of the key chemicals of this type is methyl methacrylate. Of the 4 billion pounds produced each year, roughly 85% is made using the acetone-cyanohydrin process, which requires handling of large quantities of hydrogen cyanide and produces ammonium sulfate wastes that pose an environmental disposal challenge. The U.S. Department of Energy and Eastman Chemical Company are sharing the cost of research to develop an alternative process for the synthesis of methyl methacrylate from syngas. Research Triangle Institute is focusing on the synthesis and testing of active catalysts for the condensation reactions, and Bechtel is analyzing the costs to determine the competitiveness of several process alternatives. Results thus far show that the catalysts for the condensation of formaldehyde and the propionate are key to selectively producing the desired product, methacrylic acid, with a high yield. These condensation catalysts have both acid and base functions and the strength and distribution of these acid-base sites controls the product selectivity and yield.

  19. Distributional Fate of Elements during the Synthesis of Zeolites from South African Coal Fly Ash

    Directory of Open Access Journals (Sweden)

    Pieter W. Du Plessis

    2014-04-01

    Full Text Available The synthesis of zeolites from South African coal fly ash has been deemed a viable solution to the growing economical strain caused by the disposal of ash in the country. Two synthesis routes have been studied thus far namely the 2-step method and the fusion assisted process. Fly ash contains several elements originating from coal which is incorporated in the ash during combustion. It is vital to determine the final destination of these elements in order to unveil optimization opportunities for scale-up purposes. The aim of this study was to perform a material balance study on both synthesis routes to determine the distributional fate of these elements during the synthesis of zeolites. Zeolites were first synthesized by means of the two synthesis routes. The composition of all raw materials and products were determined after which an overall and elemental balance were performed. Results indicated that in the 2-step method almost all elements were concentrated in the solid zeolite product while during the fusion assisted route the elements mostly report to the solid waste. Toxic elements such as Pb, Hg, Al, As and Nb were found in both the supernatant waste and washing water resulting from each synthesis route. It has also been seen that large quantities of Si and Al are wasted in the supernatant waste. It is highly recommended that the opportunity to recycle this liquid waste be investigated for scale-up purposes. Results also indicate that efficiency whereby Si and Al are extracted from fused ash is exceptionally poor and should be optimized.

  20. Synthesis and characterization of zeolite material from coal ashes modified by surfactant

    International Nuclear Information System (INIS)

    Fungaro, D.A.; Borrely, S.I.

    2010-01-01

    Coal ash was used as starting material for zeolite synthesis by means of hydrothermal treatment. The surfactant-modified zeolite (SMZ) was prepared by adsorbing the cationic surfactant hexadecyltrimethylammonium bromide (HDTMA-Br) on the external surface of the zeolite from coal ash. The zeolite structure stability was monitored during the characterization of the materials by FTIR, XDR and SEM. The structural parameters of surfactant-modified zeolite are very close to that of corresponding non-modified zeolite which indicates that the crystalline nature of the zeolite remained intact after required chemical treatment with HDTMA-Br molecules and heating treatment for drying. The most intense peaks in the FTIR spectrum of HDTMA-Br were observed in SMZ spectrum confirming adsorption of surfactant on zeolites. (author)

  1. Design of generic coal conversion facilities: Production of oxygenates from synthesis gas---A technology review

    Energy Technology Data Exchange (ETDEWEB)

    1991-10-01

    This report concentrates on the production of oxygenates from coal via gasification and indirect liquefaction. At the present the majority of oxygenate synthesis programs are at laboratory scale. Exceptions include commercial and demonstration scale plants for methanol and higher alcohols production, and ethers such as MTBE. Research and development work has concentrated on elucidating the fundamental transport and kinetic limitations governing various reactor configurations. But of equal or greater importance has been investigations into the optimal catalyst composition and process conditions for the production of various oxygenates.

  2. The economic production of alcohol fuels from coal-derived synthesis gas

    Energy Technology Data Exchange (ETDEWEB)

    Kugler, E.L.; Dadyburjor, D.B.; Yang, R.Y.K. [West Virginia Univ., Morgantown, WV (United States)] [and others

    1995-12-31

    The objectives of this project are to discover, (1) study and evaluate novel heterogeneous catalytic systems for the production of oxygenated fuel enhancers from synthesis gas. Specifically, alternative methods of preparing catalysts are to be investigated, and novel catalysts, including sulfur-tolerant ones, are to be pursued. (Task 1); (2) explore, analytically and on the bench scale, novel reactor and process concepts for use in converting syngas to liquid fuel products. (Task 1); (3) simulate by computer the most energy efficient and economically efficient process for converting coal to energy, with primary focus on converting syngas to fuel alcohols. (Task 2); (4) develop on the bench scale the best holistic combination of chemistry, catalyst, reactor and total process configuration integrated with the overall coal conversion process to achieve economic optimization for the conversion of syngas to liquid products within the framework of achieving the maximum cost effective transformation of coal to energy equivalents. (Tasks 1 and 2); and (5) evaluate the combustion, emission and performance characteristics of fuel alcohols and blends of alcohols with petroleum-based fuels. (Task 2)

  3. Reuse of Coconut Shell, Rice Husk, and Coal Ash Blends in Geopolymer Synthesis

    Science.gov (United States)

    Walmiki Samadhi, Tjokorde; Wulandari, Winny; Prasetyo, Muhammad Iqbal; Rizki Fernando, Muhammad

    2017-10-01

    Mixtures of biomass and coal ashes are likely to be produced in increasing volume as biomass-based energy production is gaining importance in Indonesia. This work highlights the reuse of coconut shell ash (CSA), rice husk ash (RHA), and coal fly ash (FA) for geopolymer synthesis by an activator solution containing concentrated KOH and Na2SiO3. Ash blend compositions are varied according to a simplex-centroid mixture experimental design. Activator to ash mass ratios are varied from 0.8 to 2.0, the higher value being applied for ash compositions with higher Si/Al ratio. The impact of ash blend composition on early strength is adequately modeled by an incomplete quadratic mixture model. Overall, the ashes can produce geopolymer mortars with an early strength exceeding the Indonesian SNI 15-2049-2004 standard minimum value of 2.0 MPa. Good workability of the geopolymer is indicated by their initial setting times which are longer than the minimum value of 45 mins. Geopolymers composed predominantly of RHA composition exhibit poor strength and excessive setting time. FTIR spectroscopy confirms the geopolymerization of the ashes by the shift of the Si-O-Si/Al asymmetric stretching vibrational mode. Overall, these results point to the feasibility of geopolymerization as a reuse pathway for biomass combustion waste.

  4. Polish visit

    CERN Document Server

    2003-01-01

    On 6 October, Professor Michal Kleiber, Polish Minister of Science and Chairman of the State Committee for Scientific Research, visited CERN and met both the current and designated Director General, Luciano Maiani and Robert Aymar. Professor Kleiber visited the CMS and ATLAS detector assembly halls, the underground cavern for ATLAS, and the LHC superconducting magnet string test hall. Michal Kleiber (left), Polish minister of science and Jan Krolikowski, scientist at Warsaw University and working for CMS, who shows the prototypes of the Muon Trigger board of CMS.

  5. A preliminary plant design study for the production of diesel from coal via fischer-tropsch synthesis

    International Nuclear Information System (INIS)

    Kamil, M.; Saleem, M.

    2010-01-01

    Pakistan's reliance on conventional means of producing energy has proven to be an inadequate strategy for overcoming it. The situation direly demands diversification of our energy resources not only to overcome current fiasco but also in planning for future. Among the other alternative sources, coal is the main source for producing cheaper electricity being available as huge reserves. This paper presents the preliminary plant design and cost estimation for the production of diesel from coal via coal gasification and fischer-Tropschs synthesis. Prelimnary design calculations and cost estimation are presented along with underlying assumptions. The results reveal that the diesel produced from this process might be cheaper than the crude oil based diesel. (author)

  6. Interaction of coal-derived synthesis gas impurities with solid oxide fuel cell metallic components

    Energy Technology Data Exchange (ETDEWEB)

    Marina, Olga A.; Coyle, Christopher A.; Edwards, Danny J.; Chou, Yeong-Shyung; Cramer, Carolyn N. [Pacific Northwest National Laboratory, Richland, WA 99352 (United States); Pederson, Larry R. [North Dakota State University, Fargo, ND 58102 (United States)

    2011-01-15

    Oxidation-resistant alloys find use as interconnect materials, heat exchangers, and gas supply tubing in solid oxide fuel cell (SOFC) systems, especially when operated at temperatures below {proportional_to}800 C. If fueled with synthesis gas derived from coal or biomass, such metallic components could be exposed to impurities contained in those fuel sources. In this study, coupons of ferritic stainless steels Crofer 22 APU and SS 441, austenitic nickel-chromium superalloy Inconel 600, and an alumina-forming high nickel alloy alumel were exposed to synthesis gas containing {<=}2 ppm phosphorus, arsenic and antimony, and reaction products were tested. Crofer 22 APU coupons coated with a (Mn,Co){sub 3}O{sub 4} protective layer were also evaluated. Phosphorus was found to be the most reactive. On Crofer 22 APU, the (Mn,Cr){sub 3}O{sub 4} passivation layer reacted to form an Mn-P-O product, predicted to be manganese phosphate from thermochemical calculations, and Cr{sub 2}O{sub 3}. On SS 441, reaction of phosphorus with (Mn,Cr){sub 3}O{sub 4} led to the formation of manganese phosphate as well as an Fe-P product, predicted from thermochemical calculations to be Fe{sub 3}P. Minimal interactions with antimony or arsenic in synthesis gas were limited to Fe-Sb and Fe-As solid solution formation. Though not intended for use on the anode side, a (Mn,Co){sub 3}O{sub 4} spinel coating on Crofer 22 APU reacted with phosphorus in synthesis gas to produce products consistent with Mn{sub 3}(PO{sub 4}){sub 2} and Co{sub 2}P. A thin Cr{sub 2}O{sub 3} passivation layer on Inconel 600 did not prevent the formation of nickel phosphides and arsenides and of iron phosphides and arsenides, though no reaction with Cr{sub 2}O{sub 3} was apparent. On alumel, an Al{sub 2}O{sub 3} passivation layer rich in Ni did not prevent the formation of nickel phosphides, arsenides, and antimonides, though no reaction with Al{sub 2}O{sub 3} occurred. This work shows that unprotected metallic components of

  7. Synthesis of Zeolite from Coal Fly Ash: Its Application as Water Sorbent

    Directory of Open Access Journals (Sweden)

    Prasert Pavasant

    2010-03-01

    Full Text Available Coal fly ash (CFA was used as raw material for zeolite synthesis by fusion method. In detail, it was mixed with NaOH (with ratio of 2.25 and treated under various temperatures. Synthesized zeolite was characterized using various techniques i.e. X-rayfluorescence (XRF, X-ray diffraction (XRD, and BET surface area analysis. It was found that the surface area of synthesized zeolite were in the range of 49.407-69.136 m2/g depending on the preparing condition, compared to the surface area of CFA about 17.163 m2/g. In addition, according to the XRD result, it was proven that the form of zeolite was Sodium Aluminum Silicate Hydrate (1.08Na2O.Al2O3.1.68SiO2.1.8H2O. The synthesized zeolite was then applied as water sorbent to remove water from ethanol solution (95%. The testing results revealed that the optimal fusion temperature was 450.C, which provided maximum percentage of water removal from ethanol solution (from 95% ethanol to 99.25% ethanol. For comparison, commercial-grade molecular sieve was also tested and was found to increase ethanol concentration from 95% to 99.61%. Hence, it is concluded that our synthesized zeolite provides comparable performance to the commercial-grade molecular sieve.

  8. Green synthesis of carbon quantum dots from lignite coal and the application in Fe3+ detection

    Science.gov (United States)

    Liu, Xuexia; Hao, Juanyuan; Liu, Jianhui; Tao, Hongcai

    2018-02-01

    Carbon quantum dots (CQDs) had attracted much attention due to their unique structures and excellent properties. Their green preparation was one of the research frontiers. However, most of the CQDs were prepared by strong acid oxidation, the way of which was not friendly to the environment. In this study, CQDs were prepared by green ozone oxidation of lignite coal, which is abundant and inexpensive. The CQDs were well dispersed, the size distribution of the obtained CQDs centralized from 2 to 4 nm with the average diameter of about 2.8 nm. In addition, the as-prepared CQDs containing rich oxygen functional groups exhibited good water-solubility and optical properties with yield reached 35%. The CQDs showed a highly sensitive and selective quenching effect to Fe3+ with desirable anti-interference performance. Moreover, the fluorescence intensity of CQDs had a good linear response to the Fe3+ concentration ranging from 10 to 150 µmol/L with the detection limit of 0.26 µmol/L. This green and facile synthesis method had the prospect of large-scale preparation of CQDs.

  9. Nd{sup 3+}-doped colloidal SiO{sub 2} composite abrasives: Synthesis and the effects on chemical mechanical polishing (CMP) performances of sapphire wafers

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Tingting; Lei, Hong, E-mail: hong_lei2005@aliyun.com

    2017-08-15

    Highlights: • The novel Nd{sup 3+}-doped colloidal SiO{sub 2} abrasives were synthesized by seed-introduced method. • The Nd{sup 3+}-doped colloidal SiO{sub 2} abrasives exhibited lower Ra and higher MRR on sapphire during CMP. • The cores SiO{sub 2} were coated by the shells (SiO{sub 2}, Nd{sub 2}Si{sub 2}O{sub 7} and Nd(OH){sub 3}) via chemical bonds and hydrogen bonds. • XPS analysis revealed the solid-state chemical reaction between Nd{sup 3+}-doped colloidal SiO{sub 2} abrasives and sapphire during CMP. - Abstract: Abrasive is one of the most important factors in chemical mechanical polishing (CMP). In order to improve the polishing qualities of sapphire substrates, the novel Nd{sup 3+}-doped colloidal SiO{sub 2} composite abrasives were prepared by seed-induced growth method. In this work, there were a series of condensation reactions during the synthesis process of Nd{sup 3+}-doped colloidal SiO{sub 2} composite abrasives and the silica cores were coated by shells (which contains SiO{sub 2}, Nd{sub 2}Si{sub 2}O{sub 7} and Nd(OH){sub 3}) via chemical bonds and hydrogen bonds in the Nd{sup 3+}-doped colloidal SiO{sub 2} composite abrasives, which made the composite abrasives’ core-shell structure more sTable Scanning electron microscopy (SEM) showed that Nd{sup 3+}-doped colloidal SiO{sub 2} composite abrasives were spherical and uniform in size. And the acting mechanisms of Nd{sup 3+}-doped colloidal SiO{sub 2} composite abrasives on sapphire in CMP were investigated. Time-of-flight secondary ion mass spectroscopy (TOF-SIMS) analysis and X-ray photoelectron spectroscopy (XPS) analysis demonstrated that the solid-state chemical reactions between the shells (which contained SiO{sub 2}, Nd{sub 2}Si{sub 2}O{sub 7} and Nd(OH){sub 3}) of Nd{sup 3+}-doped colloidal SiO{sub 2} composite abrasives and the sapphire occurred during the CMP process. Furthermore, Nd{sup 3+}-doped colloidal SiO{sub 2} composite abrasives exhibited lower surface roughness and

  10. Teck Coal's reclamation research program : a synthesis of 40 years of experience in mountain mine reclamation

    Energy Technology Data Exchange (ETDEWEB)

    Straker, J. [Integral Ecology Group Ltd., Victoria, BC (Canada); O' Brien, B.; Jones, R. [Teck Coal Limited, Calgary, AB (Canada)

    2010-07-01

    Teck Coal has undertaken a project to compile data and interpretations from reclamation research conducted at the company's various open-pit metallurgical coal mining operations in British Columbia and Alberta. The reclamation research synthesis project aims to compile into a single document all the reclamation research done on Teck Coal properties, to synthesize the findings of the research in a single reference, to clearly articulate research findings and optimum reclamation practices, and to shape future reclamation and monitoring efforts according to identified challenges or high-priority issues. The implementation involves reproducing all the documents as digital appendices to the synthesis document, creating summaries of every report, and categorizing according to topic area. An in-progress sample of the summary and synthesis completed to date was presented. It focused on the reclamation of ungulate habitat in southeast British Columbia. The sample involved identification of preferred elk browse and forage species, the reclamation of preferred forage species (both grass/forb and tree/shrub), the relative advantages of native and naturalized and introduced grass and forb species, techniques for survival, and nutritional characteristics. The priorities identified were to develop seed mixes to improve performance and meet changing reclamation objectives, to replicate the benefits of individual plant protectors with less cost/effort, and to determine the quantity or proportion of ungulate browse shrub species necessary for high-quality winter-range habitat. The synthesis document is to guide future reclamation work, educate new reclamation practitioners, and contribute more widely to overall reclamation knowledge. 1 ref., 2 tabs., 1 fig.

  11. Impact of Contaminants Present in Coal-Biomass Derived Synthesis Gas on Water-gas Shift and Fischer-Tropsch Synthesis Catalysts

    Energy Technology Data Exchange (ETDEWEB)

    Alptekin, Gokhan [TDA Research, Inc., Wheat Ridge, CO (United States)

    2013-02-15

    Co-gasification of biomass and coal in large-scale, Integrated Gasification Combined Cycle (IGCC) plants increases the efficiency and reduces the environmental impact of making synthesis gas ("syngas") that can be used in Coal-Biomass-to-Liquids (CBTL) processes for producing transportation fuels. However, the water-gas shift (WGS) and Fischer-Tropsch synthesis (FTS) catalysts used in these processes may be poisoned by multiple contaminants found in coal-biomass derived syngas; sulfur species, trace toxic metals, halides, nitrogen species, the vapors of alkali metals and their salts (e.g., KCl and NaCl), ammonia, and phosphorous. Thus, it is essential to develop a fundamental understanding of poisoning/inhibition mechanisms before investing in the development of any costly mitigation technologies. We therefore investigated the impact of potential contaminants (H2S, NH3, HCN, AsH3, PH3, HCl, NaCl, KCl, AS3, NH4NO3, NH4OH, KNO3, HBr, HF, and HNO3) on the performance and lifetime of commercially available and generic (prepared in-house) WGS and FT catalysts.

  12. The prospects of hard and brown coal in Poland and in the European Union

    Energy Technology Data Exchange (ETDEWEB)

    Gawlik, Lidia; Majchrzak, Henryk; Mokrzycki, Eugeniusz; Uliasz-Bochenczyk, Alicja

    2010-09-15

    Poland possess significant reserves of hard and brown coal and is an important producer of these fuels, for that reason coal has a dominant position in Polish energy balance. The government document describing energy policy of Poland up to the year 2030 treats Polish coal as an stabilizer of national energy safety. The progress in clean coal technologies development is a key element to determine the role of Polish coal both in Polish and EU economy. The possibilities of prospective use of coal pointing at the main direction of clean technology development has also been discussed in the paper.

  13. Primary Rock Temperature Fields in Czech and Polish Part of the Upper of the Upper Silesian Coal Basin / Pole temperatury pierwotnej skał w czeskiej i polskiej części górnośląskiego okręgu węglowego

    Science.gov (United States)

    Doležal, Libor; Knechtel, Józef; Taufer, Antonín; Trávníček, Ludvík

    2013-03-01

    Knowledge of the temperature of rock mass is no doubt of substantial meaning, both for the solution of economicaly demanding protection of mine workers in difficult microclimatic environment and for perspective usage of geothermal energy from the depth of the earth. International cooperation of our and Polish specialists is in this sense more than welcome, also because the exploitation of coal seams takes place in the same Upper Silesia rock coal basin. This profesional article is concentrated on complex analysis of temperature fields of the Ostrava- Karviná district, mainly from results of thermologging measurements in geological survey boreholes both on surface and underground, and also from the actual temperature measurements in the coal mines. One chapter of this article describes the original approach to the survey of temperature field and its prognosis in the Polish part of the Upper Silesia coal basin by a researcher from GIG Katowice. The most suitable method of analysis of primary temperature field seemed the preparation of isocurves of temperature(isothermal lines) for the existing mine working areas, even if the method of obtaining them was different. The Czech method is based on determination of the quantitative dependence of temperature on the rock mass depth from the abovementioned measurement results, calculation of geothermal gradients and the following recalculation of real temperature values for various depth levels. Then isothermal lines for these depth levels are created together with colour distingushing of their value limits. The Polish method is sufficiently described in a dedicated chapter. The conclusion of the article underlines the decisive role of the structuraly tectonic composition of the rock mass on the temperature field in the long term thermic evolution of the Earth.

  14. Synthesis, characterisation, optical and luminescence properties of CoAl2O4

    Science.gov (United States)

    Agilandeswari, K.; Kumar, A. Ruban

    2015-06-01

    Solid state method has been used as an efficient method to synthesize blue pigment CoAl2O4 at a temperature of 800°C. The products were characterized by powder X-ray diffraction (XRD), Fourier transformer infrared spectroscopy (FTIR), UV-Visible diffuse reflectance spectroscopy (DRS) and luminescent spectroscopy. X-ray diffraction pattern confirmed the formation of single phase CoAl2O4. Optical properties of CoAl2O4 ceramic shows an energy band gap in the range of 3.10eV. The emission spectra of spinel CoAl2O4 in the visible region confirmed the presence of tetrahedral coordinated Co2+ ions.

  15. One-Step DME synthesis from coal-derived, CO-rich syngas in a slurry reactor

    Energy Technology Data Exchange (ETDEWEB)

    Seo, Y.; Jo, S.H.; Ryu, H.J.; Yi, C.K.; Jin, G.T. [Korea Institute of Energy Research, Taejon (Republic of Korea). Zero Emission Technology Research Center

    2008-07-15

    This study investigates one-step dimethyl ether (DME) synthesis from coal-derived, CO-rich syngas over a bifunctional catalyst comprising a methanol synthesis catalyst (Cu/ZnO/Al{sub 2}O{sub 3}) and a methanol dehydration catalyst ({gamma}-Al{sub 2}O{sub 3}). The liquid-phase DME synthesis was carried out in a slurry reactor that provided good mixing and excellent heat removal. Higher CO conversion and DME space time yield (STY) were observed at a higher reaction temperature and a higher pressure. A lower gas hourly space velocity (GHSV) cansed higher CO conversion, but a lower DME STY. Excessive content of {gamma}-Al{sub 2}O{sub 3} had an adverse effect on both CO conversion and DME STY. Among various H{sub 2}:CO ratios, the maximum DME STY (13.5 mol/kg-cat/h) was observed at a H{sub 2}:CO ratio of 1-0. CO{sub 2} in the feed syngas had a negative effect on DME synthesis. The results and data obtained in this study can be used as basic data for the design and operation of a large scale bubble column reactor and for further application to a three-phase fluidized bed reactor.

  16. The economical production of alcohol fuels from coal-derived synthesis gas. Quarterly technical progress report No. 5, October 1, 1992--December 31, 1992

    Energy Technology Data Exchange (ETDEWEB)

    1993-01-01

    Two base case flow sheets have now been prepared. In the first, which was originally presented in TPR4, a Texaco gasifier is used. Natural gas is also burned in sufficient quantity to increase the hydrogen to carbon monoxide ratio of the synthesis gas to the required value of 1. 1 for alcohol synthesis. Acid gas clean up and sulfur removal are accomplished using the Rectisol process followed by the Claus and Beavon processes. About 10% of the synthesis gas is sent to a power generation unit in order to produce electric power, with the remaining 90% used for alcohol synthesis. For this process, the estimated installed cost is $474.2 mm. The estimated annual operating costs are $64.5 MM. At a price of alcohol fuels in the vicinity of $1. 00/gal, the pay back period for construction of this plant is about four years. The details of this case, called Base Case 1, are presented in Appendix 1. The second base case, called Base Case 2, also has a detailed description and explanation in Appendix 1. In Base Case 2, a Lurgi Gasifier is used. The motivation for using a Lurgi Gasifier is that it runs at a lower temperature and pressure and, therefore, produces by-products such as coal liquids which can be sold. Based upon the economics of joint production, discussed in Technical Progress Report 4, this is a necessity. Since synthesis gas from natural gas is always less expensive to produce than from coal, then alcohol fuels will always be less expensive to produce from natural gas than from coal. Therefore, the only way to make coal- derived alcohol fuels economically competitive is to decrease the cost of production of coal-derived synthesis gas. one method for accomplishing this is to sell the by-products from the gasification step. The details of this strategy are discussed in Appendix 3.

  17. Synthesis of zeolites Na-A and Na-X from tablet compressed and calcinated coal fly ash

    Science.gov (United States)

    Hu, Tao; Gao, Wenyan; Liu, Xin; Zhang, Yifu; Meng, Changgong

    2017-10-01

    Zeolites Na-A and Na-X are important synthetic zeolites widely used for separation and adsorption in industry. It is of great significance to develop energy-efficient routines that can synthesize zeolites Na-A and Na-X from low-cost raw materials. Coal fly ash (CFA) is the major residue from the combustion of coal and biomass containing more than 85% SiO2 and Al2O3, which can readily replace the conventionally used sodium silicate and aluminate for zeolite synthesis. We used Na2CO3 to replace the expensive NaOH used for the calcination of CFA and showed that tablet compression can enhance the contact with Na2CO3 for the activation of CFA through calcination for the synthesis of zeolites Na-A and Na-X under mild conditions. We optimized the control variables for zeolite synthesis and showed that phase-pure zeolite Na-A can be synthesized with CFA at reactant molar ratio, hydrothermal reaction temperature and reaction time of 1.3Na2O: 0.6Al2O3: 1SiO2: 38H2O at 80°C for 6 h, respectively, while phase-pure zeolite Na-X can be synthesized at 2.2Na2O: 0.2Al2O3: 1SiO2: 88H2O at 100°C for 8 h, respectively. The composition, morphology, specific surface area, vibration spectrum and thermogravimetry of synthesized Na-A and Na-X were further characterized.

  18. Efficient and large scale synthesis of graphene from coal and its film electrical properties studies.

    Science.gov (United States)

    Wu, Yingpeng; Ma, Yanfeng; Wang, Yan; Huang, Lu; Li, Na; Zhang, Tengfei; Zhang, Yi; Wan, Xiangjian; Huang, Yi; Chen, Yongsheng

    2013-02-01

    Coal, which is abundant and has an incompact structure, is a good candidate to replace graphite as the raw material for the production of graphene. Here, a new solution phase technique for the preparation of graphene from coal has been developed. The precursor: graphene oxide got from coal was examined by atomic force microscopy, dynamic light scattering and X-ray diffraction, the results showed the GO was a small and single layer sheet. The graphene was examined by X-ray photoelectron spectroscopy, and Raman spectroscopy. Furthermore, graphene films have been prepared using direct solution process and the electrical conductivity and Hall effect have been studied. The results showed the conductivity of the films could reach as high as 2.5 x 10(5) Sm(-1) and exhibited an n-type behavior.

  19. Highly Dispersed Re-Doped CoAl2O4 Nanopigments: Synthesis and Chromatic Properties

    Directory of Open Access Journals (Sweden)

    Yuping Tong

    2016-01-01

    Full Text Available Nanosized spinel CoAl2-xRexO4 complex oxides were prepared by self-propagation combustion method. The products have been characterized by XRD, SEM, and EDS. The results indicated that Al3+ can be partly replaced by Re3+ when the doped amount is less than 10%, which forms single solid solution. The NIR reflectance and chromatic properties of samples have also been investigated. The substitution of Re3+ for Al3+ in CoAl2O4 can increase the blueness of pigments. SEM results revealed that the obtained CoAl2-xRexO4 pigments consisted of highly dispersed spherical-like nanoparticles with uniform size distribution. EDS results indicated that the distribution of element was considerably uniform with no chemical segregation phenomenon.

  20. Metal polish poisoning

    Science.gov (United States)

    Metal polishes are used to clean metals, including brass, copper, or silver. This article discusses the harmful effects from swallowing metal polish. This article is for information only. DO NOT use ...

  1. Williamson Polishing & Plating Site

    Science.gov (United States)

    Williamson Polishing & Plating Co. Inc. was a plating shop located in the Martindale-Brightwood neighborhood of Indianapolis. The facility conducted job shop polishing and electroplating services. The vacant site contains a 14,651-square-foot building.

  2. Bioconversion of coal-derived synthesis gas to liquid fuels. Annual report, September 29, 1992--September 28, 1993

    Energy Technology Data Exchange (ETDEWEB)

    Jain, M.K.; Worden, R.M.; Grethlein, H.E.

    1993-10-21

    The overall objective of the project is to develop and optimize a two-stage fermentation process for the conversion of coal derived synthesis gas in an mixture of alcohols. The goals include the development of superior strains with high product tolerance and productivity, optimization of process conditions for high volumetric productivity and product concentrations, integration and optimization of two stage syngas fermentation, evaluation of bioreactor configurations for enhanced mass transfer, evaluation of syngas conversion by a culture of Butyribacterium methyltrophicum and Clostridium acetobutylicum, development of a membrane based pervaporation system for in situ removal of alcohols, and development of a process for reduction of carbon and electron loss. The specific goals for year one (September 1992 - September 1993) were (1) development of a project work plan, (2) development of superior CO-utilizing strains, (3) optimization of process conditions for conversion of synthesis gas to a mixture of acids in a continuously stirred reactor (CSTR), (4) evaluation of different bioreactor configurations for maximization of mass transfer of synthesis gas, (5) development of a membrane based pervaporation system, and (6) reduction of carbon and electron loss via H{sub 2}CO{sub 2} fermentation. Experimentation and progress toward these goals are described in this report.

  3. Bioconversion of coal-derived synthesis gas to liquid fuels. Quarterly technical progress report, April 1, 1993--June 30, 1993

    Energy Technology Data Exchange (ETDEWEB)

    Jain, M.K.; Worden, R.M.; Grethlein, H.

    1993-07-16

    The overall objective of the project is to develop two stage fermentation process for conversion of coal-derived synthesis gas to a mixture of alcohols. This is achieved in two steps. In the first step, B .methylotrophicum converts carbon monoxide (CO) to butyric and acetic acids. Subsequent fermentation of the acids by Clostridium acetobutylicum leads to the production of butanol and ethanol. The tasks for this quarter were: Development/isolation of superior strains for fermentation of syn gas; optimization of process conditions for fermentation of syn gas; evaluation of bioreactor configuration for improved mass transfer of syn gas; and optimization of process conditions for reducing carbon and electron loss by H{sub 2}-CO{sub 2} fermentation.

  4. Coal Transition in Poland. An historical case study for the project 'Coal Transitions: Research and Dialogue on the Future of Coal'

    International Nuclear Information System (INIS)

    Szpor, Aleksander

    2017-01-01

    This is one of the 6 country case-studies commissioned to collect experience on past coal transitions. The 6 countries are: Czech Republic, the Netherlands, Poland, Spain, UK, USA. Their role in the Coal Transitions project was to provide background information for a Synthesis Report for decision makers, and provide general lessons for national project teams to take into account in developing their coal transitions pathways for the future. The restructuring of the Polish coal sector is inextricably related to the democratic transformation which began in 1989. The economic dimension of the transformation is manifested in the shift from central planning to the free market. Although this process brought economic growth, it has had severe social costs. The main goals of the coal sector restructuring were to achieve its profitability and competitiveness on the global market. However, even with a very quick down-sizing of production and employment, which positively affected the mines' productivity, these goals were not achieved. Neither the profitability of the sector nor the sustainability of the labour restructuring were achieved. There were three main reasons for lack of success in this process. Firstly, the rapid changes of governments making impossible implementation of long term strategies and ensure implementation of market rules in the sector. Secondly, the pressure from trade unions on sustaining the status quo - state owed structure of mining companies, professional privileges and increasing salaries. Thirdly, the lack of sufficient incentives for retraining the miners and revitalising the areas exposed the most on the coal sector restructuring. Content: Introduction; Historical background; Structure of the coal and energy sector; Policies for the restructuring of the coal sector: Main actors in the process, Governmental programs, Instruments for easing the restructuring processes; Conclusions and lessons learnt

  5. Hydrothermal Synthesis of SBA-15 Using Sodium Silicate Derived from Coal Gangue

    Directory of Open Access Journals (Sweden)

    Jing Wang

    2013-01-01

    Full Text Available Well-ordered SBA-15 was prepared with a hydrothermal route by sodium silicate derived from coal gangue. The as-prepared sample was analyzed by SAXRD, BET, TEM, and SEM, respectively. The results indicate that at a low hydrothermal temperature of 100∘C the well-ordered mesoporous SBA-15 could be synthesized. The surface area, pore volume, and pore size of the sample are 552 m2/g, 0.54 cm3/g, and 7.0 nm, respectively. It is suggested that coal gangue could be used in obtaining an Si source to prepare mesoporous materials, such as SBA-15.

  6. Synthesis Of 2- (1- Naphthyl) Ethanoic Acid ( Plant Growth Regulator ) From Coal Tar And Its Application

    International Nuclear Information System (INIS)

    Khin Mooh Theint; Tin Myint Htwe

    2011-12-01

    Plant growth regulators, which are commonly called as plant hormones, naturally produced non-nutrient chemical compounds involved in growth and development. Among the various kinds of plant growth regulators, 2- (1- Naphthyl ) ethanoic acid especially encourages the root development of the plant. In this work, NAA was successfuly synthesized from naphthalene which was extracted from coal tar. The purity of naphthalene, -Chloromethyl naphthalene, -Naphthyl acetonitrile, - Naphthyl acetic acid or 2 - ( 1-Naphthyl ) ethanoic acid were also confirmed by Thin Layer Chromatography, and by spectroscopy methods. The yield percent of NAA based on naphthalene was found to be 2.1%. The yield percent of naphthaleneFrom coal tar is found to be 4.09%. The effect of NAA on root development was also studied in different concentrations of soy bean (Glycine max)and cow pea (Vigna catjang walp).

  7. Zeolite A synthesis employing a brazilian coal ash as the silicon and aluminum source and its applications in adsorption and pigment formulation

    Directory of Open Access Journals (Sweden)

    Lindiane Bieseki

    2012-01-01

    Full Text Available Zeolite A was synthesized using the coal ash from Siderópolis/RS - Brazil. The synthesis was based on a standard IZA synthesis using coal ash as the Si and Al source. XRF analysis showed that the coal ash has a Si/Al ratio of 1.52, which is close to the Si/Al ratio required to produce zeolite A (1.0. The synthesized materials were analyzed by XRD, SEM and N2 adsorption. More crystalline materials were obtained during synthesis when an additional treatment was applied at a temperature of 353 K at the dissolution of NaOH step. The product formed after 4 hours was the most crystalline, but even the product formed after 1 hour proved to be better than that formed using the standard 4 hours IZA synthesis. The zeolites synthesized by this method had an adsorption capacity of 120 mg.g-1 for Ca2+, half the capacity of commercial zeolite A (300 mg.g-1. It was not possible to obtain blue or green pigments using the synthesized zeolite A.

  8. Zeolite A synthesis employing a brazilian coal ash as the silicon and aluminum source and its applications in adsorption and pigment formulation

    Directory of Open Access Journals (Sweden)

    Lindiane Bieseki

    2013-02-01

    Full Text Available Zeolite A was synthesized using the coal ash from Siderópolis/RS - Brazil. The synthesis was based on a standard IZA synthesis using coal ash as the Si and Al source. XRF analysis showed that the coal ash has a Si/Al ratio of 1.52, which is close to the Si/Al ratio required to produce zeolite A (1.0. The synthesized materials were analyzed by XRD, SEM and N2 adsorption. More crystalline materials were obtained during synthesis when an additional treatment was applied at a temperature of 353 K at the dissolution of NaOH step. The product formed after 4 hours was the most crystalline, but even the product formed after 1 hour proved to be better than that formed using the standard 4 hours IZA synthesis. The zeolites synthesized by this method had an adsorption capacity of 120 mg.g-1 for Ca2+, half the capacity of commercial zeolite A (300 mg.g-1. It was not possible to obtain blue or green pigments using the synthesized zeolite A.

  9. Bioconversion of coal derived synthesis gas to liquid fuels. Final quarterly technical progress report, July 1, 1993--September 30, 1993

    Energy Technology Data Exchange (ETDEWEB)

    Jain, M.K.; Worden, R.M.; Grethlein, H.

    1993-10-25

    The overall objective of the project is to develop an integrated two stage fermentation process for conversion of coal-derived synthesis gas to a mixture of alcohols. This is achieved in two steps. In the first step, Butyribacterium methylotrophicum converts carbon monoxide (CO) to butyric and acetic acids. Subsequent fermentation of the acids by Clostridium acetobutylicum leads to the production of butanol and ethanol. The tasks for this quarter were: (1) development/isolation of superior strains for fermentation of syngas, (2) optimization of process conditions for fermentation of syngas, (3) evaluation of bioreactor configuration for improved mass transfer of syngas, (4) development of a membrane-based pervaporation system, (5) optimization of process conditions for reducing carbon and electron loss by H{sub 2}-CO{sub 2} fermentation, and (6) synthesis gas fermentation in single-stage by co-culture. Progress is reported in isolation of CO utilizing anaerobic strains; investigating the product profile for the fermentation of syngas by B. methylotrophicum; and determining the effect of carbon monoxide on growth of C. acetobutylicum.

  10. Synthesis on coal gases: exploitation, risks and impacts on the environment

    International Nuclear Information System (INIS)

    Bonijoly, D.; Fabriol, H.; Bazargan, B.; Defossez, P.; Lary, L. de; Leynet, A.; Schumacher, J.P.; Didier, C.; Andres, S.; Bonnard, R.; Lahaie, F.; Pokryszka, Z.

    2013-10-01

    After some generalities on coal gas (origin, fracturing, classification, present production in the world, regulatory obligations), this report proposes an overview of present extraction methods and techniques and a simplified analysis of risks and impacts on the environment. It distinguishes between accidental risks (leakages in different locations or components, uncontrolled gas migration), environmental impacts (on water, air quality, soil quality, health, and ecosystems, and greenhouse gas emissions), and other pollutions (traffic, noise, land use, induced seismicity, underground fires). Perspectives for research are discussed in terms of lacks of knowledge, scientific, technical and financial deadlocks

  11. Small-Scale Coal-Biomass to Liquids Production Using Highly Selective Fischer-Tropsch Synthesis

    Energy Technology Data Exchange (ETDEWEB)

    Gangwal, Santosh K. [Southern Research Institute, Durham, NC (United States); McCabe, Kevin [Southern Research Institute, Durham, NC (United States)

    2015-04-30

    The research project advanced coal-to-liquids (CTL) and coal-biomass to liquids (CBTL) processes by testing and validating Chevron’s highly selective and active cobalt-zeolite hybrid Fischer-Tropsch (FT) catalyst to convert gasifier syngas predominantly to gasoline, jet fuel and diesel range hydrocarbon liquids, thereby eliminating expensive wax upgrading operations The National Carbon Capture Center (NCCC) operated by Southern Company (SC) at Wilsonville, Alabama served as the host site for the gasifier slip-stream testing/demonstration. Southern Research designed, installed and commissioned a bench scale skid mounted FT reactor system (SR-CBTL test rig) that was fully integrated with a slip stream from SC/NCCC’s transport integrated gasifier (TRIGTM). The test-rig was designed to receive up to 5 lb/h raw syngas augmented with bottled syngas to adjust the H2/CO molar ratio to 2, clean it to cobalt FT catalyst specifications, and produce liquid FT products at the design capacity of 2 to 4 L/day. It employed a 2-inch diameter boiling water jacketed fixed-bed heat-exchange FT reactor incorporating Chevron’s catalyst in Intramicron’s high thermal conductivity micro-fibrous entrapped catalyst (MFEC) packing to efficiently remove heat produced by the highly exothermic FT reaction.

  12. Integrated synthesis of zeolites 4A and Na-P1 using coal fly ash for application in the formulation of detergents and swine wastewater treatment.

    Science.gov (United States)

    Cardoso, Ariela M; Horn, Martha B; Ferret, Lizete S; Azevedo, Carla M N; Pires, Marçal

    2015-04-28

    Several researchers have reported zeolite synthesis using coal ash for a wide range of applications. However, little attention has been given to green processes, including moderate synthesis conditions, using waste as raw material and effluent reuse or reduction. In this study, Brazilian coal fly ashes were used for integrated synthesis of zeolites 4A and Na-P1 by two different routes and under moderate operating conditions (temperature and pressure). Both procedures produced zeolites with similar conversions (zeolite 4A at 82% purity and zeolite Na-P1 at 57-61%) and high CEC values (zeolites 4A: 4.5meqCa(2+)g(-1) and zeolites Na-P1: 2.6-2.8meqNH4(+)g(-1)). However, process 1 generated less effluent for the zeolite mass produced (7mLg(-1)), with low residual Si and Al levels and 74% of the Si available in the coal fly ash incorporated into the zeolite, while only 55% is used in process 2. For use as a builder in detergents, synthetic zeolite 4A exhibited conformity parameters equal to or greater than those of the commercial zeolite adopted as reference. Treatment of swine wastewater with zeolite Na-P1 resulted in a high removal capacity for total ammoniacal nitrogen (31mgg(-1)). Copyright © 2015 Elsevier B.V. All rights reserved.

  13. Polish Cartographical Review

    Directory of Open Access Journals (Sweden)

    Nedjeljko Frančula

    2017-07-01

    Full Text Available The Polish Cartographical Review (PCR journal has been published in English four times a year since 2015. The journal is in open access and it is published by De Gruyter Open. It is edited by Polish scientists in collaboration with international experts.

  14. The economical production of alcohol fuels from coal-derived synthesis gas. Quarterly technical progress report Number 8, 1 July, 1993--30 September, 1993

    Energy Technology Data Exchange (ETDEWEB)

    1993-10-01

    Task 1, the preparation of catalyst materials, is proceeding actively. At WVU, catalysts based on Mo are being prepared using a variety of approaches to alter the oxidation state and environment of the Mo. At UCC and P, copper-based zinc chromite spinel catalysts will be prepared and tested. The modeling of the alcohol-synthesis reaction in a membrane reactor is proceeding actively. Under standard conditions, pressure drop in the membrane reactor has been shown to be negligible. In Task 2, base case designs had previously been completed with a Texaco gasifier. Now, similar designs have been completed using the Shell gasifier. A comparison of the payback periods or production cost of these plants shows significant differences among the base cases. However, a natural gas only design, prepared for comparison purposes, gives a lower payback period or production cost. Since the alcohol synthesis portion of the above processes is the same, the best way to make coal-derived higher alcohols more attractive economically than natural gas-derived higher alcohols is by making coal-derived syngas less expensive than natural gas-derived syngas. The maximum economically feasible capacity for a higher alcohol plant from coal-derived syngas appears to be 32 MM bbl/yr. This is based on consideration of regional coal supply in the eastern US, coal transportation, and regional product demand. The benefits of economics of scale are illustrated for the base case designs. A value for higher alcohol blends has been determined by appropriate combination of RVP, octane number, and oxygen content, using MTBE as a reference. This analysis suggests that the high RVP of methanol in combination with its higher water solubility make higher alcohols more valuable than methanol.

  15. Synthesis of zeolite-P from coal fly ash derivative and its utilisation in mine-water remediation

    Directory of Open Access Journals (Sweden)

    Leslie F. Petrik

    2010-05-01

    Full Text Available Solid residues resulting from the active treatment of acid mine drainage with coal fly ash were successfully converted to zeolite-P under mild hydrothermal treatment conditions. Scanning electron microscopy showed that the zeolite-P product was highly crystalline. The product had a high cation exchange capacity (178.7 meq / 100 g and surface area (69.1 m2/g and has potential application in waste-water treatment. A mineralogical analysis of the final product identified zeolite-P, as well as mullite and quartz phases, which indicated incomplete dissolution of the fly ash feedstock during the ageing step. Further optimisation of the synthesis conditions would be required to attain complete utilisation of the feedstock. The zeolite-P was tested for decontamination potential of circumneutral mine water. High removal efficiency was observed in the first treatment, but varied for different contaminants. The synthesised zeolite-P exhibited a high efficiency for the removal of heavy metal cations, such as aluminium, iron, manganese, zinc, copper and nickel, from contaminated mine water, even with repeated use. For potassium, calcium, strontium and barium, the removal was only efficient in the first treatment and decreased rapidly with subsequent treatments, indicating preferential adsorption of the other metals. A continuous release of sodium was observed during decontamination experiments, which decreased with subsequent treatments, confirming that sodium was the main exchangeable charge-balancing cation present in the zeolite-P product.

  16. Coking coal outlook from a coal producer's perspective

    International Nuclear Information System (INIS)

    Thrasher, E.

    2008-01-01

    Australian mine production is recovering from massive flooding while Canadian coal shipments are limited by mine and rail capacity. Polish, Czech, and Russian coking coal shipments have been reduced and United States coking coal shipments are reaching their maximum capacity. On the demand side, the Chinese government has increased export taxes on metallurgical coal, coking coal, and thermal coal. Customers seem to be purchasing in waves and steel prices are declining. This presentation addressed the global outlook for coal as well as the challenges ahead in terms of supply and demand. Supply challenges include regulatory uncertainty; environmental permitting; labor; and geology of remaining reserves. Demand challenges include global economic uncertainty; foreign exchange values; the effect of customers making direct investments in mining operations; and freight rates. Consolidation of the coal industry continued and several examples were provided. The presentation also discussed other topics such as coking coal production issues; delayed mining permits and environmental issues; coking coal contract negotiations; and stock values of coking coal producers in the United States. It was concluded that consolidation will continue throughout the natural resource sector. tabs., figs

  17. Direct synthesis of carbon nanofibers from South African coal fly ash

    Science.gov (United States)

    Hintsho, Nomso; Shaikjee, Ahmed; Masenda, Hilary; Naidoo, Deena; Billing, Dave; Franklyn, Paul; Durbach, Shane

    2014-08-01

    Carbon nanofibers (CNFs), cylindrical nanostructures containing graphene, were synthesized directly from South African fly ash (a waste product formed during the combustion of coal). The CNFs (as well as other carbonaceous materials like carbon nanotubes (CNTs)) were produced by the catalytic chemical vapour deposition method (CCVD) in the presence of acetylene gas at temperatures ranging from 400°C to 700°C. The fly ash and its carbonaceous products were characterized by transmission electron microscopy (TEM), thermogravimetric analysis (TGA), laser Raman spectroscopy and Brunauer-Emmett-Teller (BET) surface area measurements. It was observed that as-received fly ash was capable of producing CNFs in high yield by CCVD, starting at a relatively low temperature of 400°C. Laser Raman spectra and TGA thermograms showed that the carbonaceous products which formed were mostly disordered. Small bundles of CNTs and CNFs observed by TEM and energy-dispersive spectroscopy (EDS) showed that the catalyst most likely responsible for CNF formation was iron in the form of cementite; X-ray diffraction (XRD) and Mössbauer spectroscopy confirmed these findings.

  18. Synthesis and characterization of zeolite material from coal ashes modified by surfactant; Sintese e caracterizacao de material zeolitico de cinzas de carvao modificado por surfactante

    Energy Technology Data Exchange (ETDEWEB)

    Fungaro, D.A., E-mail: dfungaro@ipen.b [Instituto de Pesquisas Energeticas e Nucleares (CQMA/IPEN/CNEN-SP), Sao Paulo, SP (Brazil). Centro de Quimica e Meio Ambiente; Borrely, S.I. [Instituto de Pesquisas Energeticas e Nucleares (CTR/IPEN/CNEN-SP), Sao Paulo, SP (Brazil). Centro de Tecnologia das Radiacoes

    2010-07-01

    Coal ash was used as starting material for zeolite synthesis by means of hydrothermal treatment. The surfactant-modified zeolite (SMZ) was prepared by adsorbing the cationic surfactant hexadecyltrimethylammonium bromide (HDTMA-Br) on the external surface of the zeolite from coal ash. The zeolite structure stability was monitored during the characterization of the materials by FTIR, XDR and SEM. The structural parameters of surfactant-modified zeolite are very close to that of corresponding non-modified zeolite which indicates that the crystalline nature of the zeolite remained intact after required chemical treatment with HDTMA-Br molecules and heating treatment for drying. The most intense peaks in the FTIR spectrum of HDTMA-Br were observed in SMZ spectrum confirming adsorption of surfactant on zeolites. (author)

  19. Coal geopolitics

    International Nuclear Information System (INIS)

    Giraud, P.N.; Suissa, A.; Coiffard, J.; Cretin, D.

    1991-01-01

    This book divided into seven chapters, describes coal economic cycle. Chapter one: coals definition; the principle characteristics and properties (origin, calorific power, international classification...) Chapter two: the international coal cycle: coal mining, exploration, coal reserves estimation, coal handling coal industry and environmental impacts. Chapter three: the world coal reserves. Chapter four: the consumptions, productions and trade. Chapter five: the international coal market (exporting mining companies; importing companies; distributors and spot market operators) chapter six: the international coal trade chapter seven: the coal price formation. 234 refs.; 94 figs. and tabs [fr

  20. Hydrothermal Synthesis of Zeolite from Coal Class F Fly Ash. Influence of Temperature

    Directory of Open Access Journals (Sweden)

    Goñi, S.

    2010-06-01

    Full Text Available The influence of temperature of alkaline hydrothermal treatment on the conversion in zeolite of Spanish coal low calcium-fly ash (ASTM class F is presented in this work. Zeolite Na-P1 gismondine type (Na6Al6Si10O32.12H2O was formed at the temperature of 100ºC, which transformed in zeolite; analcime-C type (Na(Si2AlO6H2O and sodalite (1.08 Na2O.Al2O3.1.68SiO2.1.8H2O at 200ºC together with traces of tobermorite-11Å (Ca5(OH2Si6O16.4H2O. At this temperature the 100% of the fly ash reaction was allowed. An equivalent study was carried out in water as reference. The zeolite conversion of the fly ash was characterized by X ray diffraction (XRD, FT infrared (FTIR spectroscopy, surface area (BET-N2 and thermal analyses.

    En este trabajo se presenta el papel que juega la temperatura durante el tratamiento hidrotermal en medio alcalino para convertir una ceniza volante de bajo contenido en cal (clase F, según la norma ASTM en zeolita. Durante este tratamiento a la temperatura de 100ºC se forma Zeolita Na-P1 tipo gismondina (Na6Al6Si10O32.12H2O; al elevar la temperatura a 200ºC, dicha zeolita se transforma en zeolita Analcima C (Na(Si2AlO6H2O y en fase sodalita (1.08 Na2O.Al2O3.1.68SiO2.1.8H2O junto con trazas de tobermorita-11Å (Ca5(OH2Si6O16.4H2O. A esta temperatura y en estas condiciones se ha conseguido un 100% de reacción. Un estudio equivalente se ha llevado a cabo empleando agua como medio de referencia. La conversión de ceniza volante en zeolita se ha caracterizado mediante técnicas, como difracción de Rayos X (DRX, espectroscopia

  1. The state of documentation of methane resources of coal mines in the Upper Silesian coal basin

    Energy Technology Data Exchange (ETDEWEB)

    Kwarcinski, J. [Polish Geological Institute, Sosnowiec (Poland). Upper Silesian Branch

    1995-08-01

    The Polish Ministers` Council Economic Committee Resolution of 27 July 1962 required that coalbed methane reserves should be treated as a coal associated resource. Thus it is necessary to estimate the reserves of methane occurring within mining properties or coal exploration projects. The methodology for methane resource calculation is described. As of 1 January 1994, 22 coal mines had documented methane reserves as a coal associated resource. However, considerable reserves of coalbed methane in the Upper Silesian Coal Basin are not yet documented according to formal procedures and are not included into the State Resource Balance Sheets. 10 refs., 3 figs., 1 tab.

  2. Functional Median Polish

    KAUST Repository

    Sun, Ying

    2012-08-03

    This article proposes functional median polish, an extension of univariate median polish, for one-way and two-way functional analysis of variance (ANOVA). The functional median polish estimates the functional grand effect and functional main factor effects based on functional medians in an additive functional ANOVA model assuming no interaction among factors. A functional rank test is used to assess whether the functional main factor effects are significant. The robustness of the functional median polish is demonstrated by comparing its performance with the traditional functional ANOVA fitted by means under different outlier models in simulation studies. The functional median polish is illustrated on various applications in climate science, including one-way and two-way ANOVA when functional data are either curves or images. Specifically, Canadian temperature data, U. S. precipitation observations and outputs of global and regional climate models are considered, which can facilitate the research on the close link between local climate and the occurrence or severity of some diseases and other threats to human health. © 2012 International Biometric Society.

  3. Synthesis of Zeolites Prepared from Coal Bottom Ash: Influence of Time, Temperature and NaOH Concentration

    OpenAIRE

    Matsinhe,J. V.; Macuvele,D. L.P.; Santos,E.S.W.; Moreira,J. C.; Uamusse, M. M.; Muller,L.; Martins,G. J.M.; Riella,H. G.

    2017-01-01

    Nowadays, the main application of coal mine in the world is to produce energy through thermoelectric power plants. Energy generation is always associated with the production of enormous amounts of ashes, both bottom and fly ashes. The main objective of this work is to study the effect of time, temperate and concentration on Synthetic zeolites produced from utilizing minerals of coal bottom ash. However, for the factor significance analysis, factorial planning of two levels and three factors w...

  4. The Polish Cyborg. A Reflection on the Relationship between Man and Machine in Early Polish Modernism

    Directory of Open Access Journals (Sweden)

    Emiliano Ranocchi

    2016-12-01

    Full Text Available Far from being enthusiastic “modernolatry” of Italian futurism, Polish futurism demonstrates an attitude of ambivalence toward modernity. This is particularly evident in the Polish approach to that very synecdoche of modernity which is the machine. In his essay of 1923, the leader of the group, Bruno Jasieński, compares the fetishistic cult of the machine, which characterizes the Italian approach, with the utilitarian one of the Russians, exemplified by a quote from Majakovskij. To these two propositions, as a sort of Hegelian synthesis, he adds a Polish one consisting in the conception of the machine as a prosthesis, a continuation of the human body. Thereby he introduces an idea later known as “cyborg”. The category of cyborg is also useful to understand the work of another today almost forgotten Polish writer of the Twenties, Jerzy Sosnkowski. He was the author of a short novel, A Car, You and Me (Love of Machines, in which a whole chapter concerns the chief character’s dystopian nightmare wherein machines take control over the world. The third section of the essay deals with the idea of man a machine – an old, 18th century conception, which became actual anew in the 20th century and whose traces we can find among others in a well-known poem by Tytus Czyżewski. Thirty years before N. Wiener, Polish modernists seem to have sensed the social, political and anthropological implications of the mechanization of work.

  5. Coal and its perspectives in Poland

    International Nuclear Information System (INIS)

    Locatelli, C.

    1993-01-01

    The seminar held in Warsaw by the CIFOPE from 23 to 25 november 1992 was centered around the restructuring of the coal industry and its implications for the Polish economy in the context of the current deep-running economic reforms. Partly based on French experience, this seminar shed some light on long-term problems for Poland like the kind of industrial policy that will be needed to avoid desertification problems, the need for price reform in the pursuit of profitability, and the networks and financial aids needed to restructure on such a large scale, considering that coal is a key sector in the Polish economy

  6. Coal sector model: Source data on coal for the energy and power evaluation program (ENPEP)

    International Nuclear Information System (INIS)

    Suwala, W.

    1997-01-01

    Coal is the major primary energy source in Poland and this circumstances requires that the data on coal supply for use in energy planning models should be prepared properly. Economic sectors' development depends on many factors which are usually considered in energy planning models. Thus, data on the development of such sectors as coal mining should be consistent with the economic assumptions made in the energy planning model. Otherwise, coal data could bias the results of the energy planning model. The coal mining and coal distribution models which have been developed at the Polish Academy of Sciences could provide proper coal data of use in ENPEP and other energy planning models. The coal mining model optimizes the most important decisions related to coal productions, such as coal mines development, retirement of non-profitable mines, and construction of new mines. The model uses basic data forecasts of coal mine costs and coal production. Other factors such as demand for coal, world coal prices, etc., are parameters which constitute constraints and requirements for the coal mining development. The output of the model is the amount of coal produced and supply curves for different coal types. Such data are necessary for the coal distribution model and could also be used by ENPEP. This paper describes the model, its structure and how the results of the model could serve as coal-related data for ENPEP. Improvement of some input data forms of the BALANCE module of ENPEP are also suggested in order to facilitate data preparation. (author). 7 figs

  7. Gasification of coal-derived chars in synthesis gas mixtures under intraparticle mass-transfer-controlled conditions

    NARCIS (Netherlands)

    Bliek, A.; Lont, J.C.; van Swaaij, Willibrordus Petrus Maria

    1986-01-01

    A model has been formulated to describe the quasi-steady-state gasification of coal-derived chars in gas mixtures where both the reactants carbon dioxide and steam, and the gasification products carbon monoxide and hydrogen are present. As such, these conditions reflect the situation found in most

  8. Polish Semantic Parser

    Directory of Open Access Journals (Sweden)

    Agnieszka Grudzinska

    2000-01-01

    Full Text Available Amount of information transferred by computers grows very rapidly thus outgrowing the average man's capability of reception. It implies computer programs increase in the demand for which would be able to perform an introductory classitication or even selection of information directed to a particular receiver. Due to the complexity of the problem, we restricted it to understanding short newspaper notes. Among many conceptions formulated so far, the conceptual dependency worked out by Roger Schank has been chosen. It is a formal language of description of the semantics of pronouncement integrated with a text understanding algorithm. Substantial part of each text transformation system is a semantic parser of the Polish language. It is a module, which as the first and the only one has an access to the text in the Polish language. lt plays the role of an element, which finds relations between words of the Polish language and the formal registration. It translates sentences written in the language used by people into the language theory. The presented structure of knowledge units and the shape of understanding process algorithms are universal by virtue of the theory. On the other hand the defined knowledge units and the rules used in the algorithms ure only examples because they are constructed in order to understand short newspaper notes.

  9. Output and utilization of hard coal in Poland

    International Nuclear Information System (INIS)

    Ciszak, E.; Skrzypek, Z.

    1994-01-01

    The forecast of fuel energy consumption structure in Poland and the world until 1999, 2000 and 2001 is presented. Considerable proportion of coal in energy balance of Polish economy will be kept in the nearest future, but it claims to enter the new enterprises, which improves the quality of coals and promote the new pro-ecological technology of coal utilization. 7 refs, 3 figs, 9 tabs

  10. Discussion on Wastewater Treatment Process of Coal Chemical Industry

    Science.gov (United States)

    Zhao, Dongyan; Lun, Weijie; Wei, Junjie

    2017-12-01

    Coal chemical wastewater has such characteristics as high concentration of oil, ammonia nitrogen and COD. In this paper, treatment process of coal chemical industry is described mainly, such as pretreatment process, biochemical treatment process and polishing process. Through the recovery of phenol and ammonia and the treatment of wastewater from abroad, the new technology of wastewater treatment in coal chemical industry was expounded. Finally, The development of coal chemical wastewater treatment technology is prospected, and the pretreatment technology is emphasized. According to the diversification and utilization of water, zero discharge of coal chemical wastewater will be fulfilled.

  11. DEVELOPMENT OF NOVEL CERAMIC NANOFILM-FIBER INTEGRATED OPTICAL SENSORS FOR RAPID DETECTION OF COAL DERIVED SYNTHESIS GAS

    Energy Technology Data Exchange (ETDEWEB)

    Junhang Dong; Hai Xiao; Xiling Tang; Hongmin Jiang; Kurtis Remmel; Amardeep Kaur

    2012-09-30

    The overall goal of this project is to conduct fundamental studies on advanced ceramic materials and fiber optic devices for developing new types of high temperature (>500{degree}C) fiber optic chemical sensors (FOCS) for monitoring fossil (mainly coal) and biomass derived gases in power plants. The primary technical objective is to investigate and demonstrate the nanocrystalline doped-ceramic thin film enabled FOCS that possess desired stability, sensitivity and selectivity for in-situ, rapid gas detection in the syngas streams from gasification and combustion flue gases. This report summarizes research works of two integrated parts: (1) development of metal oxide solid thin films as sensing materials for detection and measurement of important gas components relevant to the coal- and biomass-derived syngas and combustion gas streams at high temperatures; and (2) development of fiber optic devices that are potentially useful for constructing FOCS in combination with the solid oxide thin films identified in this program.

  12. Simulation of Synthesis Gas Production from Steam Oxygen Gasification of Colombian Coal Using Aspen Plus®

    Directory of Open Access Journals (Sweden)

    Jorge E. Preciado

    2012-11-01

    Full Text Available A steady state simulation of syngas production from a Steam Oxygen Gasification process using commercial technologies was performed using Aspen Plus®. For the simulation, the average proximate and ultimate compositions of bituminous coal obtained from the Colombian Andean region were employed. The simulation was applied to conduct sensitivity analyses in the O2 to coal mass ratio, coal slurry concentration, WGS operating temperature and WGS steam to dry gas molar ratio (SDG over the key parameters: syngas molar composition, overall CO conversion in the WGS reactors, H2 rich-syngas lower heating value (LHV and thermal efficiency. The achieved information allows the selection of critical operating conditions leading to improve system efficiency and environmental performance. The results indicate that the oxygen to carbon ratio is a key variable as it affects significantly both the LHV and thermal efficiency. Nevertheless, the process becomes almost insensitive to SDG values higher than 2. Finally, a thermal efficiency of 62.6% can be reached. This result corresponds to a slurry solid concentration of 0.65, a WGS process SDG of 0.59, and a LTS reactor operating temperature of 473 K. With these fixed variables, a syngas with H2 molar composition of 92.2% and LHV of 12 MJ Nm−3 was attained.

  13. Coal-92

    International Nuclear Information System (INIS)

    Hillring, B.; Sparre, C.

    1992-11-01

    Swedish consumption of coal and coke during 1991 and trends in technology, environment and market aspects of coal use are reported. Steam coal use in the heating sector was unchanged from 1991, 1.2 Mtons. Reduced consumption in smaller district heating units (due to conversion to biofuels and gas) was compensated by increased use for power generation in cogeneration plants. Coal consumption in industry fell 0.10 Mton to 0.84 Mton due to lower production in one industry branch. Import of steam coal was 1.1 Mton (down 0.5 Mton from 1990) since new rules for strategic reserves allowed a reduction of stocks. During the last five years stocks have been reduced by 2 Mtons. Import of metallurgical coal was 1.6 Mton, unchanged from 1990. The report also gives statistics for the coal using plants in Sweden, on coal R and D, and on emission laws for coal firing. (9 tabs., 2 figs.)

  14. Geochemical Characteristics of the Bismuth and Antimony Occurrence in Some Coal Seams in the Lublin Coal Basin (LCB)

    Science.gov (United States)

    Parzentny, Henryk R.; Róg, Leokadia

    2017-06-01

    The study included 24 samples of coal with 7 cores, boreholes (7 coal seams), made by the Polish Geological Institute in Warsaw at the site of a Chelm field and 6 coal samples taken from 2 decks in the Lublin Coal mine "Bogdanka" S.A. in LCB. Based on performed tests found generally low levels of Sb and Bi in coal. In the vertical profile of the LCB contents of Bi and Sb in coal generally increases from coal seams younger to older age. Content of Bi in coal from roof part coal seams is usually higher, and ash content in the coal content of Sb are generally lower than in the carbon of the middle part decks. The content of Bi in the lateral coal deposits is unlikely to vary, and the gap in the coal content of Bi between the sampling regions coal do not exceed 1.7 g / Mg. In contrast gap Sb content in coal on the extent LCB is from 1.7 g / Mg of 5.8 g / Mg. The biggest influence on the content of Bi and Sb in coal from the LCB is probably organic matter in which these elements are scattered and do not form their own minerals.

  15. [Lysenkoism in Polish botany].

    Science.gov (United States)

    Köhler, Piotr

    2008-01-01

    Lysenkoism in Poland was never an autonomous phenomenon. The whole array of reasons for which it appeared in Polish science would require a separate study--here it only needs to be pointed out that the major reasons included terror on the part of the security service, lawlessness, the ubiquitous atmosphere of intimidation and terror, censorship, the diminishing sphere of civil liberties, political show trials, propaganda and denunciations. An important role in facilitating the introduction of Lysenkoism was played also by the reorganization of science after World War Two, the isolation of Polish science from science in the West, as well as the damage it had suffered during the war. At first, Lysenkoism was promoted in Poland by a small group of enthusiastic and uncritical proponents. A overview of the events connected with the ten years of Lysenkoism in Poland (end of 1948--beginning of 1958) shows a two-tier picture of how the 'idea' was propagated. The first tier consisted in the activities of the Association of Marxist Naturalists [Koło Przyrodników-Marksistów], which it engaged in since the end of 1948. The Association was later transformed into a Union of Marxist Naturalists, and this in turn merged, in 1952, with the Copernican Society of Polish Naturalists [Polskie Towarzystwo Przyrodników im. Kopernika]. It was that society which promoted Lysenkoism longest, until the end of 1956. The propaganda and training activities of the circle and the society prepared ground for analogous activities of the newly formed Polish Academy of Science (PAN), which--since its very establishment in 1952--engaged in promoting Lysenkoism through its Second Division. These activities were aimed at naturalists, initially at those who were prominent scientists (eg. the conference at Kuźnice, 1950/1951), and then at those who were only starting their academic career (including national courses in new biology at Dziwnów, 1952, or Kortowo, 1953 and 1955). The end to promoting

  16. Method selection for mercury removal from hard coal

    Directory of Open Access Journals (Sweden)

    Dziok Tadeusz

    2017-01-01

    Full Text Available Mercury is commonly found in coal and the coal utilization processes constitute one of the main sources of mercury emission to the environment. This issue is particularly important for Poland, because the Polish energy production sector is based on brown and hard coal. The forecasts show that this trend in energy production will continue in the coming years. At the time of the emission limits introduction, methods of reducing the mercury emission will have to be implemented in Poland. Mercury emission can be reduced as a result of using coal with a relatively low mercury content. In the case of the absence of such coals, the methods of mercury removal from coal can be implemented. The currently used and developing methods include the coal cleaning process (both the coal washing and the dry deshaling as well as the thermal pretreatment of coal (mild pyrolysis. The effectiveness of these methods various for different coals, which is caused by the diversity of coal origin, various characteristics of coal and, especially, by the various modes of mercury occurrence in coal. It should be mentioned that the coal cleaning process allows for the removal of mercury occurring in mineral matter, mainly in pyrite. The thermal pretreatment of coal allows for the removal of mercury occurring in organic matter as well as in the inorganic constituents characterized by a low temperature of mercury release. In this paper, the guidelines for the selection of mercury removal method from hard coal were presented. The guidelines were developed taking into consideration: the effectiveness of mercury removal from coal in the process of coal cleaning and thermal pretreatment, the synergy effect resulting from the combination of these processes, the direction of coal utilization as well as the influence of these processes on coal properties.

  17. Subjective Quality of Life of Polish, Polish-Immigrant, and Polish-American Elderly.

    Science.gov (United States)

    Berdes, Celia; Zych, Adam A.

    2000-01-01

    Compares subjective quality of life of elderly Poles living in Poland, and Polish immigrants and Polish-American ethnics living in Chicago as part of a secondary data analysis of a study initially conducted in Poland. Conclusions lend support to the idea that U.S.-born elderly people and elderly immigrants to the United States have a significantly…

  18. Bioconversion of coal-derived synthesis gas to liquid fuels. Final report, September 29, 1992--December 27, 1994

    Energy Technology Data Exchange (ETDEWEB)

    Jain, M.K.; Worden, R.M.; Grethlein, H.E.

    1995-01-15

    The proposed research project consists of an integrated, two-stage fermentation and a highly energy-efficient product separation scheme. In the first fermentation, Butyribacterium methylotrophicum converts carbon monoxide (CO) into butyric acid and acetic acids which are then converted into butanol, ethanol, and a small amount of acetone in the second stage fermentation by Clostridium acetobutylicum. An advanced separation system process, based on pervaporation, removes the alcohols from the fermentation broth as they are formed, along with some of the hydrogen sulfide (H{sub 2}S), to minimize possible inhibition of the fermentations. This bioconversion process offers a critical advantage over conventional, catalytic processes for synthesis gas conversion: the microorganisms are several orders of magnitude more sulfur tolerant than metallic catalysts. The catalysts require sulfur removal to the parts per million level, while the microorganisms are unaffected by H{sub 2}S and carbonyl sulfide (COS) at one part per hundred--roughly the composition of sulfur in raw synthesis gas. During the two-year course of this project, the following major objectives have been accomplished: demonstrated long-term cell recycle of continuous fermentation of synthesis gas; demonstrated cell immobilization of Butyribacterium methylotrophicum; identified trickle-bed reactor as a viable alternative fermentation method; modulated metabolic pathways to increase C4 formation during synthesis gas fermentation; recovered carbon and electrons from H{sub 2} and CO{sub 2} with pathway modulation for increased C4 production; developed bacterial strains with improved selectivity for butyrate fermentation; demonstrated two-stage CO to alcohol fermentation; and concentrated alcohol from solventogenic fermentation by pervaporation.

  19. ZnO template strategy for the synthesis of 3D interconnected graphene nanocapsules from coal tar pitch as supercapacitor electrode materials

    Science.gov (United States)

    He, Xiaojun; Li, Xiaojing; Ma, Hao; Han, Jiufeng; Zhang, Hao; Yu, Chang; Xiao, Nan; Qiu, Jieshan

    2017-02-01

    3D interconnected graphene nanocapsules (GNCs) were prepared from diverse aromatic hydrocarbons by a nano-ZnO-template strategy coupled with in-situ KOH activation technique. The as-made graphene networks feature thin carbonaceous shells with well-balanced micropores and mesopores. Such 3D porous networks provide freeways for good electron conduction, short pores for ion fast transport, and abundant micropores for ion adsorption. As the electrodes in supercapacitors, the unique 3D GNCs show a high capacitance of 277 F g-1 at 0.05 A g-1, a good rate performance of 194 F g-1 at 20 A g-1, and an excellent cycle stability with over 97.4% capacitance retention after 15000 cycles in 6 M KOH electrolyte. This synthesis strategy paves a universal way for mass production of 3D graphene materials from diverse aromatic hydrocarbon sources including coal tar pitch and petroleum pitch for high performance supercapacitors as well as support and sorbent.

  20. Tooth polishing: The current status

    Directory of Open Access Journals (Sweden)

    Madhuri Alankar Sawai

    2015-01-01

    Full Text Available Healthy teeth and gums make a person feel confident and fit. As people go about their daily routines and with different eating and drinking habits, the tooth enamel turns yellowish or gets stained. Polishing traditionally has been associated with the prophylaxis procedure in most dental practices, which patients know and expect. However, with overzealous use of polishing procedure, there is wearing of the superficial tooth structure. This would lead to more accumulation of local deposits. Also, it takes a long time for the formation of the fluoride-rich layer of the tooth again. Hence, now-a-days, polishing is not advised as a part of routine oral prophylaxis procedure but is done selectively based on the patients′ need. The article here, gives an insight on the different aspects of the polishing process along with the different methods and agents used for the same.

  1. Lysenko affair and Polish botany.

    Science.gov (United States)

    Köhler, Piotr

    2011-01-01

    This article describes the slight impact of Lysenkoism upon Polish botany. I begin with an account of the development of plant genetics in Poland, as well as the attitude of scientists and the Polish intelligentsia toward Marxist philosophy prior to the World War II. Next I provide a short history of the introduction and demise of Lysenkoism in Polish science, with a focus on events in botany, in context with key events in Polish science from 1939 to 1958. The article outlines the little effects of Lysenkoism upon botanists and their research, as well as how botanists for the most part rejected what was often termed the "new biology." My paper shows that though Lysenko's theories received political support, and were actively promoted by a small circle of scientists and Communist party activists, they were never accepted by most botanists. Once the political climate in Poland altered after the events of 1956, Lysenko's theories were immediately abandoned.

  2. Elastic emission polishing

    Energy Technology Data Exchange (ETDEWEB)

    Loewenthal, M.; Loseke, K.; Dow, T.A.; Scattergood, R.O.

    1988-12-01

    Elastic emission polishing, also called elastic emission machining (EEM), is a process where a stream of abrasive slurry is used to remove material from a substrate and produce damage free surfaces with controlled surface form. It is a noncontacting method utilizing a thick elasto-hydrodynamic film formed between a soft rotating ball and the workpiece to control the flow of the abrasive. An apparatus was built in the Center, which consists of a stationary spindle, a two-axis table for the workpiece, and a pump to circulate the working fluid. The process is controlled by a programmable computer numerical controller (CNC), which presently can operate the spindle speed and movement of the workpiece in one axis only. This apparatus has been used to determine material removal rates on different material samples as a function of time, utilizing zirconium oxide (ZrO{sub 2}) particles suspended in distilled water as the working fluid. By continuing a study of removal rates the process should become predictable, and thus create a new, effective, yet simple tool for ultra-precision mechanical machining of surfaces.

  3. THE POLISH RECIPE

    Directory of Open Access Journals (Sweden)

    D.F. Spinu

    2017-06-01

    Full Text Available Twenty-six years ago the international community witnessed one of the most dramatic changes in economic systems. Naturally, the fall of communism in Eastern Europe and its consequences were events difficult to judge and anticipate in their immediate aftermath. Today, we have gained a much more coherent perspective on their meaning. The political liberalization of Poland in 1989 and its transition to the market economy was generally perceived as the most successful of all post-communist countries. From 1990 to 2013, Poland experienced the most outstanding economic growth within the former communist bloc. It doubled its GDP in real terms and became the only country to experience economic growth during the financial crisis of 2008-09. However, the polish secret recipe lies in the "shock therapy" adopted at the beginning of the 90's. The aim of this paper is to examine the importance of the Balcerowicz's program in creating the basis for economic stability and growth through privatization, liberalization of foreign trade, monetary reform and an open economy. We will also review the impact of this unprecedented transformation in shaping a strong, market-oriented economy.

  4. Coal - 96

    International Nuclear Information System (INIS)

    Sparre, C.

    1996-09-01

    The report deals mainly with coal consumption, but also gives some information about technology, environmental aspects and markets. Data have been collected by questionnaires or via telephone. The use of steam coal for heating was 0.8 Mtons (down 20% from 1994). Cogeneration plants were the main users. Taxes and environmental reasons cause a reduction of the coal use that will probably continue the next years. Use of steam coal in industry has been constant at a level of 0.7 Mtons. The import of metallurgical coal rests constant at a level of 1.6 Mtons. 1.2 Mtons of coke was produced, and 0.3 Mtons imported. The PFBC-plant at Vaertan, Stockholm used 0.13 Mtons of coal, while some coal fired power plants have been converted to peat and wood fuels. The average price of steam coal imported to Sweden in 1995 was 333 SEK/ton, 6% higher than in 1994. The contract prices for delivery 1996 are about the same as at the end of 1995. All cogeneration plants have some sort of SO 2 removal system, mostly wet-dry. The largest plant, at Vaesteraas, has recently invested in a SCR system for NO x removal. Most other plants are using low NO x burners or SNCR systems, based on ammonia or urea, which reduce the emissions 50 - 70%. Some statistic about the world coal market is also given in the report

  5. Polish Geophysical Solid Earth Infrastructure Contributing to EPOS

    Science.gov (United States)

    Debski, W.; Mutke, G.; Suchcicki, J.; Jozwiak, W.; Wiejacz, P.; Trojanowski, J.

    2012-04-01

    In this poster we present the current state of the main polish solid-earth-orientated infrastructures and shortly described history of their development, current state, and some plans for their future development. The presen- tation concentrates only on the classical infrastructure leaving aside for the while the the geodetic-orientated infrastructure, like GPS network and the GPS processing data centers, gravimetric infrastructure and others of this type. Polish broadband seismic infrastructure consists of 7 permanent broadband stations incorporated into the VEBSN initiative running at the polish territory and one operated in collaboration with NORSAR is settled at the Hornsund (Svalbard) polish polar station. All stations are equipped with STS-2 seismometers and polish MK-6 seismic stations providing 120 dB dynamics 100Hz sampling and data transmission in a real time to processing center. Besides this permanent broadband seismic network (PLSN) the Central Institute of Mining is running the permanent regional, short period network at the Upper Silesia area dedicated to the detailed monitoring of seismicity induced by the black coal mining activity in this area. The network consists of As the mining activity is the main source of seismicity in Poland also all mines are running underground short period networks, like for example Rudna-Polkowice copper mine seismic network consisting of 64 underground located short period seimometers. In that area, especially around the Zelazny Most: the huge post-floating artificial lake the, IGF PAS is running the local seismic array consisting of 4 short period seismometers. Besides these permanent network IGF PAN is running the portable seismic network for detailed mapping a possible natural seismic activity in selected regions of Poland. Important contribution to classical geophysical observation in the electro-magnetic field are provided by three permanent geomagnetic observatories (one at Hornsund) and supporting set of 10

  6. Polish Toxic Currency Options

    Directory of Open Access Journals (Sweden)

    Waldemar Gontarski

    2009-04-01

    Full Text Available Toxic currency options are defined on the basis of the opposition to the nature (essence of an option contract, which is justified in terms of norms founded on the general law clause of characteristics (nature of a relation (which represents an independent premise for imposing restrictions on the freedom of contracts. So-understood toxic currency options are unlawful. Indeed they contravene iuris cogentis regulations. These include for instance option contracts, which are concluded with a bank, if the bank has not informed about option risk before concluding the contract; or the barrier options, which focus only on the protection of banks interests. Therefore, such options may appear to be invalid. Therefore, performing contracts for toxic currency options may be qualified as a criminal mismanagement. For the sake of security, the manager should then take into consideration filing a claim for stating invalidity (which can be made in a court verdict. At the same time, if the supervisory board member in a commercial company, who can also be a subject to mismanagement offences, commits an omission involving lack of reaction (for example, if he/she fails to notify of the suspected offence committed by the management board members acting to the companys detriment when the management board makes the company conclude option contracts which are charged with absolute invalidity the supervisory board member so acting may be considered to act to the companys detriment. In the most recent Polish jurisprudence and judicature the standard of a good host is treated to be the last resort for determining whether the managers powers resulting from criminal regulations were performed. The manager of the exporter should not, as a rule, issue any options. Issuing options always means assuming an obligation. In the case of currency put options it is an absolute obligation to purchase a given amount in euro at exchange rate set in advance. On the other hand issuing

  7. Efficient polishing of aspheric optics

    Energy Technology Data Exchange (ETDEWEB)

    Taylor, J.S.; Piscotty, M.A.; Nguyen, N.Q.; Landram, C.S.; Ng, L.C.

    1997-04-15

    The objectives of this project are to develop, evaluate, and optimize novel designs for a polishing tool intended for ultra-precise figure corrections on aspheric optics with tolerances typical of those required for use in extreme ultraviolet (EUV) projection lithography. This work may lead to an enhanced US industrial capability for producing optics for EUV, x-ray and, other high precision applications. LLNL benefits from developments in computer-controlled polishing and the insertion of fluid mechanics modeling into the precision manufacturing area. Our accomplishments include the numerical estimation of the hydrodynamic shear stress distribution for a new polishing tool that directs and controls the interaction of an abrasive slurry with an optical surface. A key milestone is in establishing a correlation between the shear stress predicted using our fluid mechanics model and the observed removal footprint created by a prototype tool. In addition, we demonstrate the ability to remove 25 nm layers of optical glass in a manner qualitatively similar to macroscopic milling operations using a numerically- controlled machine tool. Other accomplishments include the development of computer control software for directing the polishing tool and the construction of a polishing testbed.

  8. Groundwater and underground coal gasification in Alberta

    International Nuclear Information System (INIS)

    Haluszka, A.; MacMillan, G.; Maev, S.

    2010-01-01

    Underground coal gasification has potential in Alberta. This presentation provided background information on underground coal gasification and discussed groundwater and the Laurus Energy demonstration project. A multi-disciplined approach to project assessment was described with particular reference to geologic and hydrogeologic setting; geologic mapping; and a hydrogeologic numerical model. Underground coal gasification involves the conversion of coal into synthesis gas or syngas. It can be applied to mined coal at the surface or applied to non-mined coal seams using injection and production wells. Underground coal gasification can effect groundwater as the rate of water influx into the coal seams influences the quality and composition of the syngas. Byproducts created include heat as well as water with dissolved concentrations of ammonia, phenols, salts, polyaromatic hydrocarbons, and liquid organic products from the pyrolysis of coal. A process overview of underground coal gasification was also illustrated. It was concluded that underground coal gasification has the potential in Alberta and risks to groundwater could be minimized by a properly designed project. refs., figs.

  9. Cannabinoids cases in polish athletes

    OpenAIRE

    A Pokrywka; Z Obmiński; D Kwiatkowska; R Grucza

    2009-01-01

    The aim of this study was to investigate the number of cases and the profiles of Polish athletes who had occasionally been using marijuana or hashish throughout the period of 1998-2004, with respect to: sex, age, and discipline of sport as well as the period of testing (in- and out-of-competition). Results of the study were compared with some data reported by other WADA accredited anti-doping laboratories. Totally, 13 631 urine samples taken from Polish athletes of both sexes, aged 10-67 year...

  10. Synthesis, characterization of organo-modified zeolitic nanomaterial from coal ash and application as adsorbent on remediation of contaminated water by rhodamine B and direct blue 71

    International Nuclear Information System (INIS)

    Alcântara, Raquel Reis

    2016-01-01

    The synthesis of zeolites from mineral coal fly and bottom ash was performed by alkaline hydrothermal treatment, which were named ZFA and ZBA, respectively. Organo-modified zeolites, SMZF and SMZB, were obtained from surface modification of ZFA and ZBA, respectively, using the cationic surfactant hexadecyltrimethylammonium bromide. From the remaining solutions generated in ZFA and ZBA synthesis it was possible to synthesis two new zeolites. The physicochemical characteristics of the synthesized nanomaterials zeolite as well as their respective raw materials, such as cation exchange capacity, density, specific area, chemical composition, mineralogical and morphological, among others, were determined. The adsorbents SMZF and SMZB were used to remove the dyes, Direct Blue 71 (DB71) and Rhodamine B (RB) from aqueous solutions in batch system. Thus, four systems DB71/SMZF, RB/SMZF, DB71/SMZB, RB/SMZB were investigated. The models of pseudo-first order and pseudo-second order were applied to the experimental data for the study the adsorption kinetics. The model of pseudo-second order was the one that best described the adsorption of all dye/organomodified-zeolites systems. The equilibrium adsorption was analyzed from four models isotherm, namely: Langmuir, Freundlich, Temkin and Dubinin-Radushkevich (D-B). The results show that the model Freundlich and Langmuir best described the experimental data systems DB71/SMZF and DB71/SMZB, respectively. For systems with RB, the model D-R was the best fit for both adsorbents (SMZF and SMZB). The factorial design 2 4 was applied to the analysis of the following factors influencing the adsorption process: initial concentration of dye (C o ), pH, amount of adsorbent (M) and temperature (T). Under the conditions studied it concludes with the confidence interval of 95%, which for the DB71/SMZF system, the factors and their interactions that influence more were C 0 , M, pH, pH∗M, pH∗C 0 , M∗C 0 , pH∗M∗C 0 , in that order. In DB

  11. Coal competitiveness?

    International Nuclear Information System (INIS)

    Rogeaux, B.

    2006-01-01

    Will coal electrical plants be more competitive in the coming years? Answering this one cannot be limited to merely comparing estimates based on reference electricity production costs. The competitiveness of coal will indeed depend on the final product marketed, as the MWhs are not equal: is the purpose to produce base, half-base MWh? Does the electrical equipment structure require flexible MWh (for instance in the event of significant intermittent renewable energy amounts), and therefore plants able to adjust their power rapidly? But the competitiveness of coal will also depend on many factors that will correct reference cost estimates: uncertainties, risks, externalities. These factors will need to be appreciated on a case by case basis. We introduce some of the reasoning used to better appreciate the future competitiveness of coal, and the main factors conditioning it in three contrasting regions of the world: Europe, USA, china. (author)

  12. Polish-Bulgarian-Russian, Bulgarian-Polish-Russian or Russian-Bulgarian-Polish dictionary?

    Directory of Open Access Journals (Sweden)

    Violetta Koseska-Toszewa

    2015-11-01

    Full Text Available Polish-Bulgarian-Russian, Bulgarian-Polish-Russian or Russian-Bulgarian-Polish dictionary? The trilingual dictionary (M. Duszkin, V. Koseska, J. Satoła and A. Tzoneva is being elaborated based on a working Polish-Bulgarian-Russian electronic parallel corpus authored by Maksim Duszkin, Violetta Koseska-Toszewa and Joanna Satoła-Staśkowiak, and works by A. Tzoneva. It is the first corpus comparing languages belonging to three different Slavic language groups: western, southern and eastern. Works on the dictionary are based on Gramatyka konfrontatywna bułgarsko-polska (Bulgarian-Polish confrontative grammar and the proposed there semantic-oriented interlanguage. Two types of classifiers have been introduced into the dictionary: classic and semantic. The trilingual dictionary will present a consistent and homogeneous set of facts of grammar and semantics. The Authors point out that in a traditional dictionary it is not clear for example whether aspect should be understood as imperfective / perfective form of a verb or as its meaning. Therefore in the dictionary forms and meaning are separated in a regular way. Imperfective verb form has two meanings: state and configuration of states and events culminating in state. Also perfective verb form has two meanings: event and configuration of states and events culminating in event. These meanings are described by the semantic classifiers, respectively, state and event, state1 and event1. The way of describing language units, mentioned in the article, gives a possibility to present language material (Polish, Bulgarian, Russian in any required order, hence the article’s title.

  13. Cannabinoids cases in polish athletes

    Directory of Open Access Journals (Sweden)

    A Pokrywka

    2009-07-01

    Full Text Available The aim of this study was to investigate the number of cases and the profiles of Polish athletes who had occasionally been using marijuana or hashish throughout the period of 1998-2004, with respect to: sex, age, and discipline of sport as well as the period of testing (in- and out-of-competition. Results of the study were compared with some data reported by other WADA accredited anti-doping laboratories. Totally, 13 631 urine samples taken from Polish athletes of both sexes, aged 10-67 years, performing 46 disciplines of sport were tested. Cannabinoids were detected in 267 samples. Among Polish athletes the relative number of positive THC (tetrahydrocannabinol samples was one of the highest in Europe. The group of young Polish athletes (aged 16-24 years was the most THC-positive. THC-positive cases were noted more frequently in male athletes tested during out of competitions. The so-called contact sports (rugby, ice hockey, skating, boxing, badminton, body building and acrobatic sports were those sports, where the higher risk of cannabis use was observed. The legal interpretation of some positive cannabinoids results would be difficult because of some accidental and unintentional use of the narcotics by sportsmen. It was concluded that national anti-doping organizations (NADO’s, which are competent to judge whether the anti-doping rules were violated, should take into account the possibility of non-intentional doping use of cannabinoids via passive smoking of marijuana.

  14. Sensing roughness and polish direction

    DEFF Research Database (Denmark)

    Jakobsen, Michael Linde; Olesen, Anders Sig; Larsen, Henning Engelbrecht

    2016-01-01

    needs information about the RMS-value of the surface roughness and the current direction of the scratches introduced by the polishing process. The RMS-value indicates to the operator how far he is from the final finish, and the scratch orientation is often specified by the customer in order to avoid...... structures and light scattered from scratches....

  15. Synthesis of zeolites coal ash in surfactant modified in application and removal of orange 8 acid solution: study in batch, fixed bed column and evaluation ecotoxicological

    International Nuclear Information System (INIS)

    Magdalena, Carina Pitwak

    2015-01-01

    In this study, synthesized zeolitic material from coal ash and modified cationic surfactant was used for removing the acid dye Orange 8 (AL8) by adsorption process using moving bed and fixed-bed column. The raw material and adsorbents were characterized by different techniques, such as X-ray diffraction, X-ray fluorescence spectroscopy, among others. The adsorption of AL8 was performed by moving bed in order to optimize the results when they are launched in a fixed bed. The effects of adsorption on zeolite AL8 were compared: (1) Effect of counterions Br - and Cl - surfactant used in the modification of the zeolite; (2) effect of type of coal ash used as raw material in the synthesis of zeolites (fly and bottom). The following adsorbents were used in the study: fly and bottom zeolite modified by surfactant hexadecyltrimethylammonium bromide (ZLMS-Br-Br and ZPMS-Br) and fly zeolite modified by surfactant hexadecyltrimethylammonium chloride (ZLMS-Cl). The pseudo-second-order kinetic described the adsorption of the dye on all adsorbents. The equilibrium time was reached 40, 60 and 120 min for ZLMS-Br, ZLMS-Cl and ZPMS-Br, respectively. The adsorption equilibrium was analyzed by the equations of the models of linear and nonlinear isotherms of Langmuir, Freundlich, Temkin and Dubinin- Radushkevivh (DR) and the criterion of best fit was evaluated using the error functions.The DR model was adjusted better to the experimental data for the system AL8 / ZLMS-Br, the Freundlich model for AL8 / ZLMS-Cl and Langmuir for AL8 / ZPMS. According to the Langmuir maximum adsorption capacity was 4.67, 1.48 and 1.38 mg g -1 for ZLMS-Br, ZLMS-Cl and ZPMS-Br, in order. In studies employing fixed bed columns, the effects of inlet concentration (20- 30 mg L -1 ), flow rate (4.0 -5.3 mL min -1 ) and the bed height (5, 5 - 6.5 cm) above the breakthrough curves characteristics in the adsorption system were determined. The Adams-Bohart, Thomas, Yoon-Nelson models were applied to experimental

  16. Coal -98

    International Nuclear Information System (INIS)

    Sparre, C.

    1998-01-01

    The following report deals with the use of coal and coke during 1997. Some information about technic, environmental questions and markets are also given. Data have been collected by questionnaires to major users and by telephone to minor users. Preliminary statistical data from SCB have also been used. The use of steam coal for heating purposes during 1997 was 730 000 tons and about 500 000 tons lower than in 1996. The extremely high figures of 1996 were due to twice the production of electricity because of lack of hydro power. The co-generation plants were the main users of coal. The minor plants have increased their use of forest fuels. Probably the use of steam coal will go down in the immediate years both in the heat generating and the co-generating plants. Some foreign analysts, however, estimate a doubled use of coal for energy use after 2020 because of the plans to phase out the nuclear power. During the top year 1987 coal was used in 18 hot water plants and 11 co-generation plants. 1997 these figures are 2 and 8. Taxes and environmental reasons explain this trend. The use of steam coal in the industry has been constant at the level 700 000 tons. This level is supposed to be constant or to vary with business cycles. The import of metallurgical coal in 1997 was 1.6 mill tons like the year before. 1.2 mill tons coke were produced. The coke consumption in the industry was 1.5 Mill tons. 0.3 mill tons of coke were imported. Several other plants have plans to replace the coal with forest fuels, waste fuels and NG. Even the biggest plant, Vaesteraas, has plans to build a block for bio fuels. Helsingborg has started to use wood pellets. The pellets replace most of the coal for the heat production in the co-generation plant. Norrkoeping Kraft AB has taken a fluid bed boiler for different fuels in operation, leading to more than half the coal consumption compared with previous years. They have also rebuilt one of their travelling grates for bio fuels. Stockholm

  17. Coal 95

    International Nuclear Information System (INIS)

    Sparre, C.

    1995-01-01

    The report deals with the use of coal and coke in Sweden during 1994. Some information about technology, environmental questions and markets are also given. Data have been collected by questionnaires to major users and by telephone to minor users. Preliminary statistical data from Statistics Sweden have also been used.The use of steam coal for heating purposes has been unchanged during 1994 at a level of 1 Mtons. The production in the cogeneration plants has been constant, but has increased for electricity production. The minor plants have increased their use of forest fuels. The use of steam coal will probably go down in the next years both for heat and cogeneration plants. During the top year 1987 coal was used in 18 hot water and 11 cogeneration plants. 1994 these figures are 3 and 12. Taxes and environmental reasons explain this trend. The use of steam coal in industry has been constant at the level 0.7 Mtons. The import of metallurgical coal in 1993 was 1.6 Mtons, like 1992. Import of 0.3 Mtons of coke gives the total consumption of coke in industry as 1.5 Mtons. the average price of steam coal imported to Sweden was 317 SEK/ton, 3% higher than 1993. All Swedish plants meet their emission limit of dust, SO 2 and NO x as given by county administrations or concession boards. The cogeneration plants all have some SO 2 removal system. The biggest cogeneration plant (Vaesteraas) has recently invested in a SCR NO x cleaning system. Most other plants use low NO x burners or SNR injection systems based on ammonia or urea. 2 figs, 13 tabs

  18. Clean coal combustion in domestic sector

    Energy Technology Data Exchange (ETDEWEB)

    Dreszer, K.; Kubica, K.; Sciazko, M. [Institute for Chemical Processing of Coal, Zabrze (Poland)

    1998-12-31

    Combustion of raw coal in existing domestic furnaces with a low efficiency (usually below 50%) is a source of pollutants generation like dust, SO{sub 2} and PAH including cancerogenic BAP, resulting in serious environmental problems. Emission of pollutants depends on solid fuels quality and fuel combustion parameters. Pollutants emission can be decreased by the use of upgraded coal derived solid fuels or replacement of old heating appliances with new ones with high thermal efficiency and ecological affectivity. Several ecological fuels manufacturing methods have been elaborated in the Institute for Chemical Processing of Coal. Thermal and emission tests of heating devices and solid fuels were performed with the use of IChPW experimental plant. Results were confirmed in heating devices in real heating objects. Taking results into account proposal of legal regulation for Polish domestic sector was elaborated. 4 figs., 2 tabs.

  19. Clean coal combustion in domestic sector

    Energy Technology Data Exchange (ETDEWEB)

    Dreszer, K.; Kubica, K.; Sciazko, M. (Institute for Chemical Processing of Coal, Zabrze (Poland))

    1998-01-01

    Combustion of raw coal in existing domestic furnaces with a low efficiency (usually below 50%) is a source of pollutants generation like dust, SO[sub 2] and PAH including cancerogenic BAP, resulting in serious environmental problems. Emission of pollutants depends on solid fuels quality and fuel combustion parameters. Pollutants emission can be decreased by the use of upgraded coal derived solid fuels or replacement of old heating appliances with new ones with high thermal efficiency and ecological affectivity. Several ecological fuels manufacturing methods have been elaborated in the Institute for Chemical Processing of Coal. Thermal and emission tests of heating devices and solid fuels were performed with the use of IChPW experimental plant. Results were confirmed in heating devices in real heating objects. Taking results into account proposal of legal regulation for Polish domestic sector was elaborated. 4 figs., 2 tabs.

  20. Trends in coal use - global, EU and Poland

    Science.gov (United States)

    Suwała, Wojciech; Wyrwa, Artur; Olkuski, Tadeusz

    2017-11-01

    That aim of this paper is to compare trends in global, European use of coal with tendencies in Poland, one of heavy coal dependent countries. Polish power generation is unique among OECD countries, the share of both hard coal and lignite in power generation reaches 81% [1]. Climate policy of European Union is to phase out intensive greenhouse gases sectors, thus to transform Polish power generation into less carbon intensive. Although such policy is generally accepted in Poland, the paste and practically proposed regulation that excludes coal generation from capacity mechanisms, is considered as threat to energy security. Coal is the base for generation for one simple reason, abundant in European scale hard coal reserves and significant capacities in lignite. Natural gas reserves allow to supply about 1/3 of consumption, but prices and supplies dependent hitherto on contracts with GAZPROM did not allow to develop significant generation capacities. Renewable resources are limited, there is not much possibilities for hydro, wind and solar. Poland is also one of the countries of poor air quality, traditional coal based space heating systems plus obsolete car fleet generate vast emissions, especially during the winter. Only recently this became top priority of environmental authorities. This situation is subject to transformation, government, managers are aware that the role of coal needs to be decreased, but there are two main questions, the paste of transformation and the future energy mix. The paper attempts to answer the question whether the expected changes in Polish energy mix are comparable or differ from the global and European tendencies.

  1. Identification of plant megafossils in Pennsylvanian-age coal

    Science.gov (United States)

    Winston, R.B.

    1989-01-01

    Criteria are provided for identification of certain Pennsylvanian-age plant megafossils directly from coal based on their characteristic anatomical structures as documented from etched polished coal surfaces in comparison with other modes of preservation. Lepidophloios hallii periderm, Diaphorodendron periderm, an Alethopteris pinnule, and a Cordaites leaf were studied in material in continuity with adjacent permineralized peat (carbonate coal-ballas). Calamites wood in attachment to a pitch cast and a Psaronius stem in coal in attachment to a fusinitized Psaronius inner root mantle were studied. Sigillaria was identified in coal by comparison to its structure in permineralized peat. Other plant tissues with characteristic structures were found but could not be attributed to specific plants. ?? 1989.

  2. Coal catalysts

    Energy Technology Data Exchange (ETDEWEB)

    Kroenig, W.

    1944-02-11

    Some considerations in the selection of a catalyst for the liquid phase of coal hydrogenation are discussed. Some of the previous history of such selections is mentioned. At one stage of the development, the principal catalyst had been iron sulfate (FeSO/sub 4/.7H/sub 2/O). Later, for reasons of cost and availability of large supplies, selections had turned to mixtures of iron sulfate and one or another of some iron oxide- and aluminum oxide-containing byproducts of aluminum manufacture, namely Bayermasse, Luxamsse, or Lautamasse. Much of the discussion centered on optimal proportions for such mixtures, particularly as related to pH values of resulting coal pastes. Upper Silesian coal was more alkaline than Ruhr coal, and Bayermasse, etc., were quite alkaline. Thus, since the iron sulfate served as a partial neutralizer for the coal as well as a catalyst, it seemed necessary to increase the proportions of iron sulfate in the catalyst mixture when processing coal of greater alkalinity. A further reason for a greater proportion of iron sulfate seemed to be that most of the catalytic activity of the iron came from the ferrous iron of iron sulfate rather than from the ferric iron of the other materials. Ferrous-ferric ratios also seemed to indicate that Luxmasse or Lautamasse might be better catalyst components than Bayermasse but their water content sometimes caused handling problems, so Bayermasse had been more widely used. Formation of deposits in the preheater was more likely due to the Bayermasse than to the iron sulfate; sodium sulfide could help to prevent them.

  3. Polish energy-system modernisation

    International Nuclear Information System (INIS)

    Drozdz, M.

    2003-01-01

    The Polish energy-system needs intensive investments in new technologies, which are energy efficient, clean and cost effective. Since the early 1990s, the Polish economy has had practically full access to modern technological devices, equipment and technologies. Introducing new technologies is a difficult task for project teams, constructors and investors. The author presents a set of principles for project teams useful in planning and energy modernisation. Several essential features are discussed: Energy-efficient appliances and systems; Choice of energy carriers, media and fuels; Optimal tariffs, maximum power and installed power; Intelligent, integrated, steering systems; Waste-energy recovery; Renewable-energy recovery. In practice there are several difficulties connected with planning and realising good technological and economic solutions. The author presents his own experiences of energy-system modernisation of industrial processes and building new objects. (Author)

  4. FINANCIAL SECURITY OF POLISH HOUSEHOLDS

    Directory of Open Access Journals (Sweden)

    Agnieszka Kozera

    2016-09-01

    Full Text Available  A household’s fi nancial security is essential for the satisfaction of the needs and wants of its members, both communal and individual. It constitutes a kind of foundation for all of a household’s fi nancial decisions that impact its standard of living. The article aims to assess the level of fi nancial security of Polish households in 2005–2013. The research draws on data from Genworth Index, HBS conducted by the Central Statistical Offi ce (GUS and Social Diagnosis (Diagnoza społeczna overseen by the Social Monitoring Council. The study shows that Poland is characterized by a low level of fi nancial security relative to other European countries, especially Western and Scandinavian. More than three-quarters of Polish households experience fi nancial problems and exhibit both a low propensity to save, and low savings rates.

  5. Energy savings in Polish buildings

    Energy Technology Data Exchange (ETDEWEB)

    Markel, L.C.; Gula, A.; Reeves, G.

    1995-12-31

    A demonstration of low-cost insulation and weatherization techniques was a part of phase 1 of the Krakow Clean Fossil Fuels and Energy Efficient Project. The objectives were to identify a cost-effective set of measures to reduce energy used for space heating, determine how much energy could be saved, and foster widespread implementation of those measures. The demonstration project focused on 4 11-story buildings in a Krakow housing cooperative. Energy savings of over 20% were obtained. Most important, the procedures and materials implemented in the demonstration project have been adapted to Polish conditions and applied to other housing cooperatives, schools, and hospitals. Additional projects are being planned, in Krakow and other cities, under the direction of FEWE-Krakow, the Polish Energie Cities Network, and Biuro Rozwoju Krakowa.

  6. Earnings Management in Polish Companies

    OpenAIRE

    Brzeszczyński, Janusz; Gajdka, Jerzy; Schabek, Tomasz

    2012-01-01

    This paper presents results of the investigation of a phenomenon known as "earnings management'' (EM) among the companies listed on the Polish stock market. The distribution of earnings per share (EPS) for the stocks around the threshold value of "zero" and the threshold of "recent performance" was analyzed in the period of years 1997-2010. Moreover, the changes of earnings for the stocks, which are suspected to manipulate their earnings, were also investigated. The results, which indicate as...

  7. LOVE in English and Polish

    Directory of Open Access Journals (Sweden)

    Małgorzata Brożyna Reczko

    2017-12-01

    Full Text Available LOVE in English and Polish The paper presents a sample contrastive analysis of the linguistic picture of love in English and Polish. The material used in the survey is drawn from lexicographic data, including the British National Corpus and Narodowy Korpus Języka Polskiego [National Corpus of Polish]. The paper focuses on the similarities and differences in conceptualizing the abstract concept of love in the English and Polish languages. An analytical method, developed by Bartmiński and associates, serves as the theoretical basis for the reconstruction of the linguistic picture of the world.   MIŁOŚĆ w języku angielskim i polskim Niniejszy artykuł to próba kontrastywnego porównania językowego obrazu świata MIŁOŚCI w języku angielskim i polskim. Materiał badawczy pochodzi głównie ze źródeł leksykograficznych: słowników oraz korpusów (Narodowego Korpusu Języka Polskiego oraz z korpusu języka angielskiego British National Corpus. Celem badania było poszukiwanie podobieństw i różnic w konceptualizacji MIŁOŚCI w tych dwóch językach. Metoda badawcza została zaczerpnięta z prac J. Bartmińskiego i dotyczy rekonstrukcji językowego obrazu świata różnych pojęć.

  8. 19th Polish Control Conference

    CERN Document Server

    Kacprzyk, Janusz; Oprzędkiewicz, Krzysztof; Skruch, Paweł

    2017-01-01

    This volume contains the proceedings of the KKA 2017 – the 19th Polish Control Conference, organized by the Department of Automatics and Biomedical Engineering, AGH University of Science and Technology in Kraków, Poland on June 18–21, 2017, under the auspices of the Committee on Automatic Control and Robotics of the Polish Academy of Sciences, and the Commission for Engineering Sciences of the Polish Academy of Arts and Sciences. Part 1 deals with general issues of modeling and control, notably flow modeling and control, sliding mode, predictive, dual, etc. control. In turn, Part 2 focuses on optimization, estimation and prediction for control. Part 3 is concerned with autonomous vehicles, while Part 4 addresses applications. Part 5 discusses computer methods in control, and Part 6 examines fractional order calculus in the modeling and control of dynamic systems. Part 7 focuses on modern robotics. Part 8 deals with modeling and identification, while Part 9 deals with problems related to security, fault ...

  9. Directly polished lightweight aluminum mirror

    Science.gov (United States)

    ter Horst, Rik; Tromp, Niels; de Haan, Menno; Navarro, Ramon; Venema, Lars; Pragt, Johan

    2017-11-01

    During the last ten years, Astron has been a major contractor for the design and manufacturing of astronomical instruments for Space- and Earth based observatories, such as VISIR, MIDI, SPIFFI, X-Shooter and MIRI. Driven by the need to reduce the weight of optically ultra-stiff structures, two promising techniques have been developed in the last years: ASTRON Extreme Lightweighting [1][2] for mechanical structures and an improved Polishing Technique for Aluminum Mirrors. Using one single material for both optical components and mechanical structure simplifies the design of a cryogenic instrument significantly, it is very beneficial during instrument test and verification, and makes the instrument insensitive to temperature changes. Aluminum has been the main material used for cryogenic optical instruments, and optical aluminum mirrors are generally diamond turned. The application of a polishable hard top coating like nickel removes excess stray light caused by the groove pattern, but limits the degree of lightweighting of the mirrors due to the bi-metal effect. By directly polishing the aluminum mirror surface, the recent developments at Astron allow for using a non-exotic material for light weighted yet accurate optical mirrors, with a lower surface roughness ( 1nm RMS), higher surface accuracy and reduced light scattering. This paper presents the techniques, obtained results and a global comparison with alternative lightweight mirror solutions. Recent discussions indicate possible extensions of the extreme light weight technology to alternative materials such as Zerodur or Silicon Carbide.

  10. The economical production of alcohol fuels from coal-derived synthesis gas. Sixth quarterly technical progress report, January 1, 1993--March 31, 1993

    Energy Technology Data Exchange (ETDEWEB)

    1993-04-01

    Preliminary economic investigations have focused on cost reduction measures in the production of syngas from coal. A spread sheet model has been developed which can determine the cost of syngas production based upon the cost of equipment and raw materials and the market value of energy and by-products. In comparison to natural gas derived syngas, coal derived syngas is much more expensive, suggesting a questionable economic status of coal derived alcohol fuels. While it is possible that use of less expensive coal or significant integration of alcohol production and electricity production may reduce the cost of coal derived syngas, it is unlikely to be less costly to produce than syngas from natural gas. Fuels evaluation is being conducted in three parts. First, standard ASTM tests are being used to analyze the blend characteristics of higher alcohols. Second, the performance characteristics of higher alcohols are being evaluated in a single-cylinder research engine. Third, the emissions characteristics of higher alcohols are being investigated. The equipment is still under construction and the measurement techniques are still being developed. Of particular interest is n-butanol, since the MoS{sub 2} catalyst produces only linear higher alcohols. There is almost no information on the combustion and emission characteristics of n-butanol, hence the importance of gathering this information in this research.

  11. Facile solid-state synthesis of highly dispersed Cu nanospheres anchored on coal-based activated carbons as an efficient heterogeneous catalyst for the reduction of 4-nitrophenol

    Science.gov (United States)

    Wang, Shan; Gao, Shasha; Tang, Yakun; Wang, Lei; Jia, Dianzeng; Liu, Lang

    2018-04-01

    Coal-based activated carbons (AC) were acted as the support, Cu/AC catalysts were synthesized by a facile solid-state reaction combined with subsequent heat treatment. In Cu/AC composites, highly dispersed Cu nanospheres were anchored on AC. The catalytic activity for 4-nitrophenol (4-NP) was investigated, the effects of activation temperature and copper loading on the catalytic performance were studied. The catalysts exhibited very high catalytic activity and moderate chemical stability due to the unique characteristics of the particle-assembled nanostructures, the high surface area and the porous structure of coal-based AC and the good dispersion of metal particles. Design and preparation of non-noble metal composite catalysts provide a new direction for improving the added value of coal.

  12. Coal at the crossroads

    International Nuclear Information System (INIS)

    Scaroni, A.W.; Davis, A.; Schobert, H.; Gordon, R.L.; Ramani, R.V.; Frantz, R.L.

    1992-01-01

    Worldwide coal reserves are very large but coal suffers from an image of being an environmentally unfriendly and inconvenient fuel. Aspects discussed in the article include: coal's poor image; techniques for coal analysis, in particular instrumented techniques; developments in clean coal technology e.g. coal liquefaction, fluidized bed combustion, co-generation and fuel slurries; the environmental impact of mining and land reclamation; and health aspects. It is considered that coal's future depends on overcoming its poor image. 6 photos

  13. An Overview of Polish Martial Arts

    Directory of Open Access Journals (Sweden)

    Wojciech J. Cynarski

    2012-07-01

    Full Text Available The purpose of this study is to explain the revival of Polish martial arts from the perspectives of cultural sociology, the sciences of physical culture, and the humanistic theory of martial arts. The Polish Martial Arts (Polskie Sztuki Walki are a subject still requiring serious scientific examination, even in Poland. There are few works concerning the history of Polish weapons, and most only describe techniques for wielding specific types of edged weapons. Nevertheless, there is a large group of enthusiasts trying to restore and cultivate the old Polish tradition, a tradition with heavy emphasis on the art of fencing. The author knows many of the people and facts presented here, from personal observation and from direct participation in these arts. As a disciple of the late Master Yoshio Sugino (10th-dan Kobudo Katori Shinto-ryu, he fought against the Polish saber champion, and he has taken part in joint exhibitions of Polish and Japanese fencing.

  14. Energy efficiency and steam coal transport over long distances

    Directory of Open Access Journals (Sweden)

    Stala-Szlugaj Katarzyna

    2016-01-01

    Full Text Available Coal is one of the most important energy sources in the world. Its main consumers are the energy sector (with a 37-46% share in the years 1990-2014; 1.12-2.34 billion toe and industry (24-27%; 0.78-1.38 billion toe. Diversified distribution of coal deposits in the world in relation to its consumers means that it has to be transported over often very long distances. The global coal trade is dominated by maritime transport (90-94% in the years 2004-2014, and the share of transport by land is relatively smaller. The aim of the article was to calculate the index describing what part of the energy contained in the coal transported on a particular route is consumed by the train carrying it. Due to the dominant position of the Russian Federation in imports of coal to Poland, it was assumed that coal will be imported by rail from Kuzbass (Russia's largest coal basin. As a result of the calculation, it was found that the rate of energy consumption for transport of imported coal will be somewhere in the range of 9.22-15.26%. In the case of deliveries of hard coal from Polish producers to the power plants the calculated rate changes within the range of 0.55-0.58%.

  15. The tourism attractiveness of Polish libraries

    OpenAIRE

    Miedzińska, Magdalena; Tanaś, Sławoj

    2009-01-01

    The aim of the article is to draw the reader's attention to the tourism attractiveness of renowned Polish libraries. These have attained a tourism function due to tourism exploration and penetration, but remain in the shadow of other Polish cultural assets. The article outlines the historical geography of Polish libraries, an analysis of tourism assets and an attempt to classify and catalogue libraries in Poland.

  16. Coal derived-briquetted solid fuels

    International Nuclear Information System (INIS)

    Sciazko, M.

    1993-01-01

    Despite considerable progress, there are some regions in Central and Eastern Europe where residential heating is dominated by direct burning of bituminous or brown coal with all environmental consequences. In Poland, the residential heating consumes more than 25 mln tons of coal annually. It is estimated that during the heating season coal-fired individual home ovens and local heating stations in some Polish heavily populated areas contribute up to 22% in total emission of dust, 86% of SO 2 , and 56% of tar species. It has been proposed to replace some of the fuel, i.e. directly burnt coal by more ecological solid fuels in a form of briquettes. Considering the emissive characteristics, solid ecological fuels can be divided into two groups. The first one manufactured on the basis of high rank coals, and a cold briquetting with some additives capturing harmful combustion products. Production of these fuels is reasonably cheap and simple and the result of their use is a noticeable decrease in dust, sulfur oxides and soot emissions. The second one is ecologically clean fuel, i.e. smokeless fuel, produced on the basis of deeply degasified coals and a hot briquetting with the addition of either binder or caking coals and other compounds aimed at capturing harmful combustion products. The technology of production of the smokeless fuels is much more complicated and expensive, but as a result of their use a significant decrease in atmospheric emission is achieved. The best results are observed in decreasing the emission of tars and aromatic hydrocarbons. Technologies of production of ecological fuels are non-waste and non-emissive. The paper deals with the economical and technological side of briquetted solid fuels of both types. Emission factors of chosen components for ecological fuels with reference to primary coal are also discussed

  17. The Effect of Pore Volume of Hard Coals on Their Susceptibility to Spontaneous Combustion

    Directory of Open Access Journals (Sweden)

    Agnieszka Dudzińska

    2014-01-01

    Full Text Available In this paper the results of the experimental studies on a relationship between pore volume of hard coals and their tendency to spontaneous combustion are presented. Pore volumes were determined by the gas adsorption method and spontaneous combustion tendencies of coals were evaluated by determination of the spontaneous combustion indexes Sza and Sza′ on the basis of the current Polish standards. An increase in the spontaneous combustion susceptibility of coal occurs in the case of the rise both in micropore volumes and in macropore surfaces. Porosity of coal strongly affects the possibility of oxygen diffusion into the micropores of coal located inside its porous structure. The volume of coal micropores determined on the basis of the carbon dioxide adsorption isotherms can serve as an indicator of a susceptibility of coal to spontaneous combustion.

  18. Using Mathematica software for coal gasification simulations – Selected kinetic model application

    Directory of Open Access Journals (Sweden)

    Sebastian Iwaszenko

    2015-01-01

    Full Text Available Coal gasification is recognized as a one of promising Clean Coal Technologies. As the process itself is complicated and technologically demanding, it is subject of many research. In the paper a problem of using volumetric, non-reactive core and Johnson model for coal gasification and underground coal gasification is considered. The usage of Mathematica software for models' equations solving and analysis is presented. Coal parameters were estimated for five Polish mines: Piast, Ziemowit, Janina, Szczygłowice and Bobrek. For each coal the models' parameters were determined. The determination of parameters was based on reactivity assessment for 50% char conversion. The calculations show relatively small differences between conversion predicted by volumetric and non reactive core model. More significant differences were observed for Johnson model, but they do not exceeded 10% for final char conversion. The conceptual model for underground coal gasification was presented.

  19. Coal industry annual 1997

    International Nuclear Information System (INIS)

    1998-12-01

    Coal Industry Annual 1997 provides comprehensive information about US coal production, number of mines, prices, productivity, employment, productive capacity, and recoverable reserves. US Coal production for 1997 and previous years is based on the annual survey EIA-7A, Coal Production Report. This report presents data on coal consumption, coal distribution, coal stocks, coal prices, and coal quality for Congress, Federal and State agencies, the coal industry, and the general public. Appendix A contains a compilation of coal statistics for the major coal-producing States. This report includes a national total coal consumption for nonutility power producers that are not in the manufacturing, agriculture, mining, construction, or commercial sectors. 14 figs., 145 tabs

  20. Coal industry annual 1997

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-12-01

    Coal Industry Annual 1997 provides comprehensive information about US coal production, number of mines, prices, productivity, employment, productive capacity, and recoverable reserves. US Coal production for 1997 and previous years is based on the annual survey EIA-7A, Coal Production Report. This report presents data on coal consumption, coal distribution, coal stocks, coal prices, and coal quality for Congress, Federal and State agencies, the coal industry, and the general public. Appendix A contains a compilation of coal statistics for the major coal-producing States. This report includes a national total coal consumption for nonutility power producers that are not in the manufacturing, agriculture, mining, construction, or commercial sectors. 14 figs., 145 tabs.

  1. Perceptions of and Attitudes towards Regional Varieties of Polish: Views from Two Polish Provinces

    Science.gov (United States)

    Milobog, Magdalena; Garrett, Peter

    2011-01-01

    This paper reports a study of perceptions and attitudes relating to regional varieties of Polish. The methodology followed folk linguistic approaches to attitudes research. Respondents in two Polish provinces were asked to draw on a map of Poland where they thought the main regional varieties of Polish were spoken, and then to name and…

  2. Coal Industry Annual 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-10-01

    This report presents data on coal consumption, coal distribution, coal stocks, coal prices, coal quality, and emissions for Congress, Federal and State agencies, the coal industry, and the general public. Appendix A contains a compilation of coal statistics for the major coal-producing States. This report does not include coal consumption data for nonutility power producers that are not in the manufacturing, agriculture, mining, construction, or commercial sectors. Consumption for nonutility power producers not included in this report is estimated to be 21 million short tons for 1995.

  3. Coal industry annual 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-11-01

    This report presents data on coal consumption, coal distribution, coal stocks, coal prices, and coal quality, and emissions for Congress, Federal and State agencies, the coal industry, and the general public. Appendix A contains a compilation of coal statistics for the major coal-producing States.This report does not include coal consumption data for nonutility power producers that are not in the manufacturing, agriculture, mining, construction, or commercial sectors. Consumption for nonutility power producers not included in this report is estimated to be 24 million short tons for 1996. 14 figs., 145 tabs.

  4. Coal Industry Annual 1995

    International Nuclear Information System (INIS)

    1996-10-01

    This report presents data on coal consumption, coal distribution, coal stocks, coal prices, coal quality, and emissions for Congress, Federal and State agencies, the coal industry, and the general public. Appendix A contains a compilation of coal statistics for the major coal-producing States. This report does not include coal consumption data for nonutility power producers that are not in the manufacturing, agriculture, mining, construction, or commercial sectors. Consumption for nonutility power producers not included in this report is estimated to be 21 million short tons for 1995

  5. Coal and the competition

    Energy Technology Data Exchange (ETDEWEB)

    Morey, M. [RDI Consulting, Arlington, VA (United States). FT Energy

    2000-07-01

    24 overheads/viewgraphs outline a presentation on competition in the US coal industry. It discussed four main subjects: key factors driving coal demand (environmental regulations, electric utility deregulation; competition with natural gas, inter-regional coal competition, supply availability and pricing; and the export market and competition from off-shore coal sources); coal's ability to boost market share; shifts in coal distribution and the risk of more branded coal; and attempts to keep more regional sources of coal in business. State tax incentives for coal use in Arizona, Ohio, Oklahoma, Virginia and Alabama were discussed.

  6. Coal industry annual 1996

    International Nuclear Information System (INIS)

    1997-11-01

    This report presents data on coal consumption, coal distribution, coal stocks, coal prices, and coal quality, and emissions for Congress, Federal and State agencies, the coal industry, and the general public. Appendix A contains a compilation of coal statistics for the major coal-producing States.This report does not include coal consumption data for nonutility power producers that are not in the manufacturing, agriculture, mining, construction, or commercial sectors. Consumption for nonutility power producers not included in this report is estimated to be 24 million short tons for 1996. 14 figs., 145 tabs

  7. Strategies for sustainable development of the Polish electric power system

    International Nuclear Information System (INIS)

    Janiczek, R.

    1996-01-01

    The key features of sustainable development of the Polish electric power industry are discussed. Priorities and limitations for changes and power demand forecasts are described. Results of least-cost planning for existing power plants' modernization and generation expansion with environmental impacts are presented. The least-cost strategy is given by the optimal upgrades of older plants until year 2002 and by expansion of gas-fired units. The limited availability of gas after 2010 will lead to the construction of new coal-fired plants. For the next planning process, an integrated resource planning methodology is proposed, which includes dynamic optimization of supply and demand side options. Innovative mechanisms are shown to overcome barriers of development like long-terms contracts and decentralization of the power system planning process. (author)

  8. History of Polish gastrointestinal radiology.

    Science.gov (United States)

    Urbanik, A

    2003-12-01

    As early as several days after the publication of the information concerning Roentgen's discovery the first radiological examinations were performed in Poland. The new method was immediately introduced into medical practice, including gastroenterology. In that pioneer period the most important works were those by Walery Jaworski who was the first man in the world to perform an X-ray of gall stones as well as the stomach with the use of a contrast medium. In its more-than-a-hundred-year history Polish gastrointestinal radiology has attempted not only to catch up with the world science, but it also has made a considerable contribution to its development.

  9. Corporate Politics on Polish Millennials

    OpenAIRE

    Natalia Roślik

    2017-01-01

    In the very beginning of this particular paper, an author is trying to determine and describe who Millennials actually are. Then, the basis of Millennials definition is analysing corporation’s activity over the past years regarding this age group. The main goal of the thesis is to bring their specific futures out and describe what corporations on Polish job market are doing to encourage them to work in their offices. Especially in Poland within the last years, it is observed that big multinat...

  10. Polish Foundation for Energy Efficiency

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-12-31

    The Polish Foundation for Energy Efficiency (FEWE) was established in Poland at the end of 1990. FEWE, as an independent and non-profit organization, has the following objectives: to strive towards an energy efficient national economy, and to show the way and methods by use of which energy efficiency can be increased. The activity of the Foundation covers the entire territory of Poland through three regional centers: in Warsaw, Katowice and Cracow. FEWE employs well-known and experienced specialists within thermal and power engineering, civil engineering, economy and applied sciences. The organizer of the Foundation has been Battelle Memorial Institute - Pacific Northwest Laboratories from the USA.

  11. Energy Policies of IEA Countries: Poland [Polish version

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2011-07-01

    Poland has made commendable efforts to develop a solid energy policy framework over the last years. As energy security is a high policy priority, the country is enhancing gas supply security by building an LNG terminal, expanding underground storage capacity and increasing domestic gas production. Polish plans for developing electricity and gas cross-border links will also contribute to regional security of supply. In addition, the government has announced an ambitious nuclear programme by 2030, envisaging the first unit to enter operation by 2022. Other achievements include energy intensity improvements, an increased share of renewables and a stronger focus on energy research and development (R&D). Despite these positive developments, there is room for improving Poland’s energy strategy. First, a more integrated energy and climate policy is needed to put Poland firmly on a low-carbon path while enhancing energy security. Second, energy policy could put more emphasis on promoting competition to make the energy markets more efficient. Decarbonising Poland’s power sector will be a particularly significant challenge requiring huge investments. Coal accounts for 55% of Polish primary energy supply and 92% of electricity generation, raising significant climate change and environmental challenges. To this end, Poland’s efforts to improve energy efficiency and to diversify the country’s energy mix are praiseworthy and should be pursued. The government’s attention to R&D on clean coal technologies, including carbon capture and storage (CCS) is also encouraging. The government could put more focus on the positive role that gas can play in decarbonising the electricity mix, especially if Poland’s potential resources of unconventional gas are confirmed. To tap these resources, it will be vital to put the necessary legal and regulatory framework in place. This in-depth review analyses the energy challenges facing Poland and provides sectoral critiques and

  12. Evaluation of Rock Bolt Support for Polish Hard Rock Mines

    Science.gov (United States)

    Skrzypkowski, Krzysztof

    2018-03-01

    The article presents different types of rock bolt support used in Polish ore mining. Individual point resin and expansion rock bolt support were characterized. The roof classes for zinc and lead and copper ore mines were presented. Furthermore, in the article laboratory tests of point resin rock bolt support in a geometric scale of 1:1 with minimal fixing length of 0.6 m were made. Static testing of point resin rock bolt support were carried out on a laboratory test facility of Department of Underground Mining which simulate mine conditions for Polish ore and hard coal mining. Laboratory tests of point resin bolts were carried out, especially for the ZGH Bolesław, zinc and lead "Olkusz - Pomorzany" mine. The primary aim of the research was to check whether at the anchoring point length of 0.6 m by means of one and a half resin cartridge, the type bolt "Olkusz - 20A" is able to overcome the load.The second purpose of the study was to obtain load - displacement characteristic with determination of the elastic and plastic range of the bolt. For the best simulation of mine conditions the station steel cylinders with an external diameter of 0.1 m and a length of 0.6 m with a core of rock from the roof of the underground excavations were used.

  13. Integrated High Temperature Coal-to-Hydrogen System with CO2 Separation

    Energy Technology Data Exchange (ETDEWEB)

    James A. Ruud; Anthony Ku; Vidya Ramaswamy; Wei Wei; Patrick Willson

    2007-05-31

    A significant barrier to the commercialization of coal-to-hydrogen technologies is high capital cost. The purity requirements for H{sub 2} fuels are generally met by using a series of unit clean-up operations for residual CO removal, sulfur removal, CO{sub 2} removal and final gas polishing to achieve pure H{sub 2}. A substantial reduction in cost can be attained by reducing the number of process operations for H{sub 2} cleanup, and process efficiency can be increased by conducting syngas cleanup at higher temperatures. The objective of this program was to develop the scientific basis for a single high-temperature syngas-cleanup module to produce a pure stream of H{sub 2} from a coal-based system. The approach was to evaluate the feasibility of a 'one box' process that combines a shift reactor with a high-temperature CO{sub 2}-selective membrane to convert CO to CO{sub 2}, remove sulfur compounds, and remove CO{sub 2} in a simple, compact, fully integrated system. A system-level design was produced for a shift reactor that incorporates a high-temperature membrane. The membrane performance targets were determined. System level benefits were evaluated for a coal-to-hydrogen system that would incorporate membranes with properties that would meet the performance targets. The scientific basis for high temperature CO{sub 2}-selective membranes was evaluated by developing and validating a model for high temperature surface flow membranes. Synthesis approaches were pursued for producing membranes that integrated control of pore size with materials adsorption properties. Room temperature reverse-selectivity for CO{sub 2} was observed and performance at higher temperatures was evaluated. Implications for future membrane development are discussed.

  14. Regional-scale geomechanical impact assessment of underground coal gasification by coupled 3D thermo-mechanical modeling

    Science.gov (United States)

    Otto, Christopher; Kempka, Thomas; Kapusta, Krzysztof; Stańczyk, Krzysztof

    2016-04-01

    Underground coal gasification (UCG) has the potential to increase the world-wide coal reserves by utilization of coal deposits not mineable by conventional methods. The UCG process involves combusting coal in situ to produce a high-calorific synthesis gas, which can be applied for electricity generation or chemical feedstock production. Apart from its high economic potentials, UCG may induce site-specific environmental impacts such as fault reactivation, induced seismicity and ground subsidence, potentially inducing groundwater pollution. Changes overburden hydraulic conductivity resulting from thermo-mechanical effects may introduce migration pathways for UCG contaminants. Due to the financial efforts associated with UCG field trials, numerical modeling has been an important methodology to study coupled processes considering UCG performance. Almost all previous UCG studies applied 1D or 2D models for that purpose, that do not allow to predict the performance of a commercial-scale UCG operation. Considering our previous findings, demonstrating that far-field models can be run at a higher computational efficiency by using temperature-independent thermo-mechanical parameters, representative coupled simulations based on complex 3D regional-scale models were employed in the present study. For that purpose, a coupled thermo-mechanical 3D model has been developed to investigate the environmental impacts of UCG based on a regional-scale of the Polish Wieczorek mine located in the Upper Silesian Coal Basin. The model size is 10 km × 10 km × 5 km with ten dipping lithological layers, a double fault and 25 UCG reactors. Six different numerical simulation scenarios were investigated, considering the transpressive stress regime present in that part of the Upper Silesian Coal Basin. Our simulation results demonstrate that the minimum distance between the UCG reactors is about the six-fold of the coal seam thickness to avoid hydraulic communication between the single UCG

  15. Coal -94

    International Nuclear Information System (INIS)

    Sparre, C.

    1994-05-01

    This report deals with use of coal and coke during 1993; information about techniques, environmental questions and markets are also given. Use of steamcoal for heating purposes has been reduced about 3 % during 1993 to 1,0 mill tons. This is the case especially for the heat generating boilers. Production in co-generation plants has been constant and has increased for electricity production. Minor plants have increased their use of forest fuels, LPG and NG. Use of steamcoal will probably go down in the immediate years both in heat generating and co-generating plants. Coal-based electricity has been imported from Denmark during 1993 corresponding to about 400 000 tons of coal, when several of our nuclear plants were stopped. Use of steamcoal in the industry has been constant at 700 000 tons. This level is supposed to be constant or to vary with business cycles. The import of metallurgical coal in 1993 was 1,6 mill tons like the year before. 1,2 mill tons coke were produced. Coke consumption in industry was 1,4 mill tons. 0,2 mill tons of coke were imported. Average price of steamcoal imported to Sweden in 1993 was 308 SEK/ton or 13 % higher than in 1992; this can be explained by the dollar price level increasing 34% in 1993. For the world, the average import price was 50,0 USD/ton, a decrease of 6 %. The coal market during 1993 was affected by less consumption in Europe, shut downs of European mines and decreasing prices. High freight price raises in Russia has affected the Russian export and the market in northern Europe. The prices have been stabilized recently. All Swedish plants meet emission limits of dust, SO 2 and NO x . Co-generation plants all have some sort of SO 2 -removal system; the wet-dry method is mostly used. A positive effect of the recently introduced NO x -duties is a 40% reduction

  16. Sexual activity of Polish adults.

    Science.gov (United States)

    Pastwa-Wojciechowska, Beata; Izdebski, Zbigniew

    2014-01-01

    The purpose of this research was to explore the subject of sexual activity in the Polish population, with special focus on age and gender differences, and sexual infidelity. Sexual activity is one of the basic factors in initiating and maintaining relationships. On the one hand, sexual activity enables us to meet natural needs and maintain an intimate relationship with another human being; on the other, it may allow us to overcome loneliness and social isolation by providing the opportunity to express feelings of closeness and unity. The research was conducted on a representative group of 3,200 Poles aged between 15-49, with the support of a well-known Polish research company - TNS OBOP. Face-to-face and Pencil and Paper (PAPI) interviews were carried out. The results focus on two main issues: the age and motives of sexual initiation among teenagers (with a significant percentage starting their sexual activity at the age of 15), and the quality of the sexual lives of adults (average number of sexual partners, sexual infidelity and sexual satisfaction). There is dependence between the type of relationship and the performance or non-performance of sexual activity, as well as the quality of the relationship. Among both adolescents and adults, remaining in a stable relationship (partnership or marriage) promotes loyalty. The performance of sexual goals turns out to be an important mechanism regulating the interpersonal aspects of a relationship, influencing their perception and evaluation.

  17. Sexual activity of Polish adults

    Directory of Open Access Journals (Sweden)

    Beata Pastwa-Wojciechowska

    2014-03-01

    Full Text Available Aim. The purpose of this research was to explore the subject of sexual activity in the Polish population, with special focus on age and gender differences, and sexual infidelity. Sexual activity is one of the basic factors in initiating and maintaining relationships. On the one hand, sexual activity enables us to meet natural needs and maintain an intimate relationship with another human being; on the other, it may allow us to overcome loneliness and social isolation by providing the opportunity to express feelings of closeness and unity. Material and method. The research was conducted on a representative group of 3,200 Poles aged between 15–49, with the support of a well-known Polish research company – TNS OBOP. Face-to-face and Pencil and Paper (PAPI interviews were carried out. Results. The results focus on two main issues: the age and motives of sexual initiation among teenagers (with a significant percentage starting their sexual activity at the age of 15, and the quality of the sexual lives of adults (average number of sexual partners, sexual infidelity and sexual satisfaction. Conclusion. There is dependence between the type of relationship and the performance or non-performance of sexual activity, as well as the quality of the relationship. Among both adolescents and adults, remaining in a stable relationship (partnership or marriage promotes loyalty. The performance of sexual goals turns out to be an important mechanism regulating the interpersonal aspects of a relationship, influencing their perception and evaluation.

  18. Buffered Electrochemical Polishing of Niobium

    Energy Technology Data Exchange (ETDEWEB)

    Ciovati, Gianluigi [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Tian, Hui [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); College of William and Mary, Williamsburg, VA (United States); Corcoran, Sean [Virginia Polytechnic Inst. and State Univ. (Virginia Tech), Blacksburg, VA (United States)

    2011-03-01

    The standard preparation of superconducting radio-frequency (SRF) cavities made of pure niobium include the removal of a 'damaged' surface layer, by buffered chemical polishing (BCP) or electropolishing (EP), after the cavities are formed. The performance of the cavities is characterized by a sharp degradation of the quality factor when the surface magnetic field exceeds about 90 mT, a phenomenon referred to as 'Q-drop.' In cavities made of polycrystalline fine grain (ASTM 5) niobium, the Q-drop can be significantly reduced by a low-temperature (? 120 °C) 'in-situ' baking of the cavity if the chemical treatment was EP rather than BCP. As part of the effort to understand this phenomenon, we investigated the effect of introducing a polarization potential during buffered chemical polishing, creating a process which is between the standard BCP and EP. While preliminary results on the application of this process to Nb cavities have been previously reported, in this contribution we focus on the characterization of this novel electrochemical process by measuring polarization curves, etching rates, surface finish, electrochemical impedance and the effects of temperature and electrolyte composition. In particular, it is shown that the anodic potential of Nb during BCP reduces the etching rate and improves the surface finish.

  19. Method of polishing nickel-base alloys and stainless steels

    Science.gov (United States)

    Steeves, Arthur F.; Buono, Donald P.

    1981-01-01

    A chemical attack polish and polishing procedure for use on metal surfaces such as nickel base alloys and stainless steels. The chemical attack polish comprises Fe(NO.sub.3).sub.3, concentrated CH.sub.3 COOH, concentrated H.sub.2 SO.sub.4 and H.sub.2 O. The polishing procedure includes saturating a polishing cloth with the chemical attack polish and submicron abrasive particles and buffing the metal surface.

  20. Coal industry annual 1993

    Energy Technology Data Exchange (ETDEWEB)

    1994-12-06

    Coal Industry Annual 1993 replaces the publication Coal Production (DOE/FIA-0125). This report presents additional tables and expanded versions of tables previously presented in Coal Production, including production, number of mines, Productivity, employment, productive capacity, and recoverable reserves. This report also presents data on coal consumption, coal distribution, coal stocks, coal prices, coal quality, and emissions for a wide audience including the Congress, Federal and State agencies, the coal industry, and the general public. In addition, Appendix A contains a compilation of coal statistics for the major coal-producing States. This report does not include coal consumption data for nonutility Power Producers who are not in the manufacturing, agriculture, mining, construction, or commercial sectors. This consumption is estimated to be 5 million short tons in 1993.

  1. Coal industry annual 1993

    International Nuclear Information System (INIS)

    1994-01-01

    Coal Industry Annual 1993 replaces the publication Coal Production (DOE/FIA-0125). This report presents additional tables and expanded versions of tables previously presented in Coal Production, including production, number of mines, Productivity, employment, productive capacity, and recoverable reserves. This report also presents data on coal consumption, coal distribution, coal stocks, coal prices, coal quality, and emissions for a wide audience including the Congress, Federal and State agencies, the coal industry, and the general public. In addition, Appendix A contains a compilation of coal statistics for the major coal-producing States. This report does not include coal consumption data for nonutility Power Producers who are not in the manufacturing, agriculture, mining, construction, or commercial sectors. This consumption is estimated to be 5 million short tons in 1993

  2. Advanced techniques for computer-controlled polishing

    Science.gov (United States)

    Schinhaerl, Markus; Stamp, Richard; Pitschke, Elmar; Rascher, Rolf; Smith, Lyndon; Smith, Gordon; Geiss, Andreas; Sperber, Peter

    2008-08-01

    Computer-controlled polishing has introduced determinism into the finishing of high-quality surfaces, for example those used as optical interfaces. Computer-controlled polishing may overcome many of the disadvantages of traditional polishing techniques. The polishing procedure is computed in terms of the surface error-profile and the material removal characteristic of the polishing tool, the influence function. Determinism and predictability not only enable more economical manufacture but also facilitate considerably increased processing accuracy. However, there are several disadvantages that serve to limit the capabilities of computer-controlled polishing, many of these are considered to be issues associated with determination of the influence function. Magnetorheological finishing has been investigated and various new techniques and approaches that dramatically enhance the potential as well as the economics of computer-controlled polishing have been developed and verified experimentally. Recent developments and advancements in computer-controlled polishing are discussed. The generic results of this research may be used in a wide variety of alternative applications in which controlled material removal is employed to achieve a desired surface specification, ranging from surface treatment processes in technical disciplines, to manipulation of biological surface textures in medical technologies.

  3. NOVEL SLURRY PHASE DIESEL CATALYSTS FOR COAL-DERIVED SYNGAS

    Energy Technology Data Exchange (ETDEWEB)

    Dr. Dragomir B. Bukur; Dr. Ketil Hanssen; Alec Klinghoffer; Dr. Lech Nowicki; Patricia O' Dowd; Dr. Hien Pham; Jian Xu

    2001-01-07

    This report describes research conducted to support the DOE program in novel slurry phase catalysts for converting coal-derived synthesis gas to diesel fuels. The primary objective of this research program is to develop attrition resistant catalysts that exhibit high activities for conversion of coal-derived syngas.

  4. Polish Industry and Art at CERN

    CERN Multimedia

    2000-01-01

    On 17 October 2000 the second Polish industrial and technological exhibition opened at CERN. The first one was held five years ago and nine of the companies that were present then have come back again this year. Six of those companies were awarded contracts with CERN in 1995. Three Polish officials were present at the Opening Ceremony today: Mrs Malgorzata Kozlowska, Under-secretary of State in the State Committee for Scientific Research, Mr Henryk Ogryczak, Under-secretary of State in Ministry of Economy and Prof. Jerzy Niewodniczanski, President of National Atomic Energy Agency. Professor Luciano Maiani welcomed the Polish delegation to CERN and stressed the important contribution of Polish scientists and industrialists to the work of the laboratory. Director General Luciano Maiani (back left) and head of SPL division Karl-Heinz Kissler (back right) visit the Poland at CERN exhibition… The exhibition offers Polish companies the opportunity to establish professional contacts with CERN. Nineteen companies...

  5. Study of the Feasibility of a Coal-to-Liquids Plant in Interior Alaska

    Science.gov (United States)

    2011-05-12

    Syngas Treatment – Fischer-Tropsch (F-T) Synthesis & Upgrading...200 MW of electricity to export – Export waste heat for district heating – Use of technologies that recover as much waste heat as possible in the...Separation Unit Coal Preparation Gasifier Syngas Treatment F-T and Upgrading Power Generation oxygen dried coal or slurried coal raw syngas syngas

  6. Coal Transition in the Czech Republic. An historical case study for the project 'Coal Transitions: Research and Dialogue on the Future of Coal'

    International Nuclear Information System (INIS)

    Reckova, Dominika; Recka, Lukacs; Scasny, Milan

    2017-01-01

    This is one of the 6 country case-studies commissioned to collect experience on past coal transitions. The 6 countries are: Czech Republic, the Netherlands, Poland, Spain, UK, USA. Their role in the Coal Transitions project was to provide background information for a Synthesis Report for decision makers, and provide general lessons for national project teams to take into account in developing their coal transitions pathways for the future. Content: History of coal production and coal reserves; Key features of the Czech economy; Fuel mix in the Czech Republic 1990 - 2014; Key features of coal sector in the Czech Republic after 1990; The use of coal in the Czech Republic and its possible replacement: A. Coal as source of Electricity, B. Coal as Heating source, C. Non - energy coal use; The state role in the coal sector after 1990 - mining limits; Measures to ease transition: Phasing-out of mining activities, Rehabilitation of environmentally damaged land, Programmes financing the remediation of ecological damage, Remediation of environmental damage caused by mining; Future outlook; Lessons learned; References; Annex

  7. Corporate Politics on Polish Millennials

    Directory of Open Access Journals (Sweden)

    Natalia Roślik

    2017-12-01

    Full Text Available In the very beginning of this particular paper, an author is trying to determine and describe who Millennials actually are. Then, the basis of Millennials definition is analysing corporation’s activity over the past years regarding this age group. The main goal of the thesis is to bring their specific futures out and describe what corporations on Polish job market are doing to encourage them to work in their offices. Especially in Poland within the last years, it is observed that big multinational companies are paying special attention to Millennials and trying to hire them before competitors will do so. As a part of this paper, an author will describe corporate politics and practices on Thomson Reuters and BNY Mellon examples. Within this work, an author is also discussing key features and differences between this generation and Millennials parent’s generation. Additionally, there is a reference to corporate social responsibility concept and work-life balance issues.

  8. Coal Tar and Coal-Tar Pitch

    Science.gov (United States)

    Learn about coal-tar products, which can raise your risk of skin cancer, lung cancer, and other types of cancer. Examples of coal-tar products include creosote, coal-tar pitch, and certain preparations used to treat skin conditions such as eczema, psoriasis, and dandruff.

  9. Liquid fuels from Canadian coals

    Energy Technology Data Exchange (ETDEWEB)

    Taylor, G.W.

    1979-06-15

    In Canadian energy planning, the central issue of security of supply must be addressed by developing flexible energy systems that make the best possible use of available resources. For liquid fuel production, oil sands and heavy oil currently appear more attractive than coal or biomass as alternatives to conventional crude oil, but the magnitude of their economic advantage is uncertain. The existence of large resources of oil sands, heavy oils, natural gas and low-sulfur coals in Western Canada creates a unique opportunity for Canadians to optimize the yield from these resources and develop new technology. Many variations on the three basic liquefaction routes - hydroliquefaction, pyrolysis and synthesis - are under investigation around the world, and the technology is advancing rapidly. Each process has merit under certain circumstances. Surface-mineable subbituminous and lignite coals of Alberta and Saskatchewan appear to offer the best combination of favorable properties, deposit size and mining cost, but other deposits in Alberta, Nova Scotia and British Columbia should not be ruled out. The research effort in Canada is small by world standards, but it is unlikely that technology could be imported that is ideally suited to Canadian conditions. Importing technology is undesirable: innovation or process modification to suit Canadian coals and markets is preferred; coprocessing of coal liquids with bitumen or heavy oils would be a uniquely Canadian, exportable technology. The cost of synthetic crude from coal in Canada is uncertain, estimates ranging from $113 to $220/m/sup 3/ ($18 to $35/bbl). Existing economic evaluations vary widely depending on assumptions, and can be misleading. Product quality is an important consideration.

  10. Smoking characteristics of Polish immigrants in Dublin

    Directory of Open Access Journals (Sweden)

    Zatonski Witold

    2008-12-01

    Full Text Available Abstract Background This study examined two main hypotheses: a Polish immigrants' smoking estimates are greater than their Irish counterparts (b Polish immigrants purchasing cigarettes from Poland smoke "heavier" (≥ 20 cigarettes a day when compared to those purchasing cigarettes from Ireland. The study also set out to identify significant predictors of 'current' smoking (some days and everyday among the Polish immigrants. Methods Dublin residents of Polish origin (n = 1,545 completed a previously validated Polish questionnaire in response to an advertisement in a local Polish lifestyle magazine over 5 weekends (July–August, 2007. The Office of Tobacco Control telephone-based monthly survey data were analyzed for the Irish population in Dublin for the same period (n = 484. Results Age-sex adjusted smoking estimates were: 47.6% (95% Confidence Interval [CI]: 47.3%; 48.0% among the Poles and 27.8% (95% CI: 27.2%; 28.4% among the general Irish population (p 24 months were significant predictors of current smoking among the Poles. An objective validation of the self-reported smoking history of a randomly selected sub-sample immigrant group, using expired carbon monoxide (CO measurements, showed a highly significant correlation coefficient (r = 0.64 of expired CO levels with the reported number of cigarettes consumed (p Conclusion Polish immigrants' smoking estimates are higher than their Irish counterparts, and particularly if employed, with only primary-level education, and are overseas >2 years.

  11. Szczyrk Conference Papers -- Part II. Coal: Issues for the Eighties

    OpenAIRE

    Vorontsov, N.V.

    1980-01-01

    This volume is the second of two Collaborative Papers which contain the technical papers presented at an IIASA Seminar under the generic title 'Coal: Issues for the Eighties' which was held in Szczyrk, Poland in November 1979. The seminar was jointly organized by IIASA and the Polish institutes collaborating in this study. The papers are here reproduced for the convenience of those attending the seminar and for reference by those involved in this continuing industry study. The first volume co...

  12. Monitor of ash content of coal with X-ray source

    International Nuclear Information System (INIS)

    Wawrzonek, L.

    1983-01-01

    The coal ash monitor is used on-line to measure the ash content of raw, washed and blended coals. The instrument consists of a presentation unit and electronic unit. In the presentation unit a compact layer of coal is formed and there is also a radiation measuring system. A plutonium 238 source is used and the backscattered X-rays are detected by a proportional counter. The count rate is processed in the electronic unit and displayed as the ash percentage in the coal. A wide range of Polish coals was analysed. The monitor was tested in a power plant over the period of one year. The ash content in the coal analysed was in the range 5 to 50%. The gauge readings were compared with the pyrolysis results. An accuracy of 3.2% (95% confidence limit) was reached. These results were not corrected for the free moisture content which varied in the range 5 to 15 %. (author)

  13. Coal Transition in the Netherlands. An historical case study for the project 'Coal Transitions: Research and Dialogue on the Future of Coal'

    International Nuclear Information System (INIS)

    Gales, Ben; Hoelsgens, Rick

    2017-01-01

    This is one of the 6 country case-studies commissioned to collect experience on past coal transitions. The 6 countries are: Czech Republic, the Netherlands, Poland, Spain, UK, USA. Their role in the Coal Transitions project was to provide background information for a Synthesis Report for decision makers, and provide general lessons for national project teams to take into account in developing their coal transitions pathways for the future. This document provides on overview of coal transitions in the Netherlands in the post-war period. The main focus is an in depth case study of the reconversion of the Limburg region in the South-east of the country which took place from 1965 to 1990. This is discussed in the first part of the document. The later part of the document discusses the re-emergence of coal as an energy source in the Netherlands and present challenges to phasing out coal use

  14. COAL Conference Poster

    OpenAIRE

    Brown, Taylor Alexander; McGibbney, Lewis John

    2017-01-01

    COAL Conference Poster This archive contains the COAL conference poster for the AGU Fall Meeting 2017 by Taylor Alexander Brown. The Inkscape SVG source is available at https://github.com/capstone-coal/coal-conference-poster/ under the Creative Commons Attribution-ShareAlike 4.0 International license.

  15. Fuel production from coal by the Mobil Oil process using nuclear high-temperature process heat

    International Nuclear Information System (INIS)

    Hoffmann, G.

    1982-01-01

    Two processes for the production of liquid hydrocarbons are presented: Direct conversion of coal into fuel (coal hydrogenation) and indirect conversion of coal into fuel (syngas production, methanol synthesis, Mobil Oil process). Both processes have several variants in which nuclear process heat may be used; in most cases, the nuclear heat is introduced in the gas production stage. The following gas production processes are compared: LURGI coal gasification process; steam reformer methanation, with and without coal hydrogasification and steam gasification of coal. (orig./EF) [de

  16. Super-polishing of Zerodur aspheres by means of conventional polishing technology

    Science.gov (United States)

    Polak, Jaroslav; Klepetková, Eva; Pošmourný, Josef; Šulc, Miroslav; Procháska, František; Tomka, David; Matoušek, Ondřej; Poláková, Ivana; Šubert, Eduard

    2015-01-01

    This paper describes a quest to find simple technique to superpolish Zerodur asphere (55μm departure from best fit sphere) that could be employed on old fashion way 1-excenter optical polishing machine. The work focuses on selection of polishing technology, study of different polishing slurries and optimization of polishing setup. It is demonstrated that either by use of fine colloidal CeO2 slurry or by use of bowl-feed polishing setup with CeO2 charged pitch we could reach 0.4nm RMS roughness while removing <30nm of surface layer. This technique, although not optimized, was successfully used to improve surface roughness on already prepolished Zerodur aspheres without necessity to involve sophisticated super-polishing technology and highly trained manpower.

  17. Update on the modernization of 200 MW hard coal power plants in Poland

    International Nuclear Information System (INIS)

    Szabo, T.E.; Kopec, M.

    1993-01-01

    In June 1990, the Coalition of 200 MW, Hard Coal, Polish Power Plants representing an installed base of 10,240 MW, including 45 units of 200 MW, signed an agreement with the Westinghouse Electric Corporation, Power Generation Business Unit, based in Orlando, Florida, to cooperate on developing a modernization program for the 200 MW units. Program funding was obtained with The United States Trade Development Program (TDP) providing approximately 2/3 of the cost, and the balance provided by Westinghouse. On March 5, 1992, the Polish-American (51% Westinghouse, 49% Seven (7) Hard Coal Power Plants), Joint Venture Company, MODELPOL, Ltd. (Polish acronym for 'MODernizacja ELektrowni POLskich' or Modernization of Polish Power Plants) was established with the goal to implement not only technically but financially the recommendations of the Modernization Study. The mission given MODELPOL, Ltd. by their Polish-American Shareholders was to: develop the specific modernization programs for each hard coal power plant; assist in identifying and obtaining the financial resources required for implementation; and provide technological preventative maintenance services to improve unit availability. Within these aims was the target to reduce SO 2 , and particulate emissions. The first program is taking place at the Laziska Power Plant, followed by Rybnik. Further projects are in the planning stages. Finance is a constant problem, this should be eased by the restructuring of the power industry. Future programmes include connection to the European Community Power Grid. 5 figs

  18. Comparative study of performance of shoe polishes formulated from ...

    African Journals Online (AJOL)

    GARZALI

    This should make the polish remains as discrete solid particles held mechanically within the leather. This work intends to explore the use of polyethylene pigment in the production of shoe polish. The shoe polish produced will be applied alongside shoe polish from carbon black (CI black Pigment 7) on finished black leather ...

  19. Coal Transition in the United States. An historical case study for the project 'Coal Transitions: Research and Dialogue on the Future of Coal'

    International Nuclear Information System (INIS)

    Kok, Irem

    2017-01-01

    This is one of the 6 country case-studies commissioned to collect experience on past coal transitions. The 6 countries are: Czech Republic, the Netherlands, Poland, Spain, UK, USA. Their role in the Coal Transitions project was to provide background information for a Synthesis Report for decision makers, and provide general lessons for national project teams to take into account in developing their coal transitions pathways for the future. Over the past decade, the US started to cut down the production and the use of coal, which was affected by unfavorable market dynamics and changing federal regulatory environment. Even before the shale gas revolution and uptake of renewables diminish the use of coal in power generation, coal communities were struggling to meet ends. The regional cost differences between producing states, such as the Appalachian and the Powder River Basins, indicates that coal-impacted communities and workers have lived through the impacts of coal transition at varying magnitudes and time periods. In the period between 2014 and 2016, we have seen the crash of major US coal companies due to declining demand for US coal domestically and internationally. Furthermore, Obama administration's climate change policies negatively impacted coal-fired power plants with additional GHG emission requirements, contributing to declining domestic demand for coal. Combined with market downturn, US coal producers already struggle to pay for high operational costs and legal liabilities under bankruptcy conditions. With under-funded state budgets, coal states are also grappling with financial exposure resulting from pension, health care and reclamation liabilities of bankrupt coal companies. In 2016, former President Obama announced the Power Plus Plan to aid coal-impacted communities and workers to prepare for a low carbon future. The federal budget plan targeted diversification of local economies, funding of health and pension funds of miners and retraining for

  20. New Environmental Practices in Polish Production Firms

    DEFF Research Database (Denmark)

    Kræmer, Trine Pipi

    2002-01-01

    Based on five case studies in Poland, the paper discusses, how a specific environmental policy influences the firms? industrial environmental practices. The study illustrates, how the Polish environmental policy, dominated by environmental charges on emissions, is extremely effective in improving...

  1. Electro Polishing of Niobium Cavities at DESY

    CERN Document Server

    Matheisen, A; Morales, H; Petersen, B; Schmoekel, M; Steinhau-Kühl, N

    2004-01-01

    At DESY a facility for electro polishing (EP) of the super conducting (s.c.) TESLA/TTF cavities have been built and is operational since summer 2003. The EP infrastructure is capable to handle single-cell structures and the standard TESLA/ TTF nine-cell cavities. Several electro polishing processes have been made since and acceleration voltage up to 40 MV/m have been reached in nine cell structures. We report on measurements and experiences gained since 2003 as well as on handling procedures developed for the preparation of electro polished resonators. Specific data like heat production, variation of current density and bath aging will be presented. Another important point for reproducible results is the quality control of the electro polishing process. First quality control steps to be implanted in the EP procedure for large-scale production will be described.

  2. Semiological analysis of Polish theater posters

    Directory of Open Access Journals (Sweden)

    Jelena Nikolić

    2016-02-01

    Full Text Available Through the application of semiological analysis to theater posters made by two Polish authors, the paper uncovers signs, meanings, codes and specifics of the „Polish school of poster-making“ and contemporary Polish posters. Aside from this, I suggest a methodological framework for studying the issue of coding and shaping a theater poster as a culturally specific form of visual communication. The aesthetic and semiotic outlook of the Polish theater posters which were chosen is analyzed using the semiological method which highlights their differences and similarities. By pointing out the system of codes through the examples given here, a graphic designer is informed about the existence and the possibilities of a more systematic approach to shaping a theater poster.

  3. Report on Polish Public Libraries 2001

    OpenAIRE

    Bednarek-Michalska, Bożena; Szatkowska, Olga

    2001-01-01

    Report is an overview of polish public libraries, services to a variety of communities, it also provides statistics, n explanation of the funding policy for public libraries in Poland and information about the governance of public libraries in the country.

  4. Coal data: A reference

    Energy Technology Data Exchange (ETDEWEB)

    1995-02-01

    This report, Coal Data: A Reference, summarizes basic information on the mining and use of coal, an important source of energy in the US. This report is written for a general audience. The goal is to cover basic material and strike a reasonable compromise between overly generalized statements and detailed analyses. The section ``Supplemental Figures and Tables`` contains statistics, graphs, maps, and other illustrations that show trends, patterns, geographic locations, and similar coal-related information. The section ``Coal Terminology and Related Information`` provides additional information about terms mentioned in the text and introduces some new terms. The last edition of Coal Data: A Reference was published in 1991. The present edition contains updated data as well as expanded reviews and additional information. Added to the text are discussions of coal quality, coal prices, unions, and strikes. The appendix has been expanded to provide statistics on a variety of additional topics, such as: trends in coal production and royalties from Federal and Indian coal leases, hours worked and earnings for coal mine employment, railroad coal shipments and revenues, waterborne coal traffic, coal export loading terminals, utility coal combustion byproducts, and trace elements in coal. The information in this report has been gleaned mainly from the sources in the bibliography. The reader interested in going beyond the scope of this report should consult these sources. The statistics are largely from reports published by the Energy Information Administration.

  5. Electrolytic polishing system for space age materials

    International Nuclear Information System (INIS)

    Coons, W.C.; Iosty, L.R.

    1976-01-01

    A simple electrolytic polishing technique was developed for preparing Cr, Co, Hf, Mo, Ni, Re, Ti, V, Zr, and their alloys for structural analysis on the optical microscope. The base electrolyte contains 5g ZnCl 2 and 15g AlCl 3 . 6H 2 O in 200 ml methyl alcohol, plus an amount of H 2 SO 4 depending on the metal being polished. Five etchants are listed

  6. Trace element analysis of nail polishes

    International Nuclear Information System (INIS)

    Misra, G.; Mittal, V.K.; Sahota, H.S.

    1999-01-01

    Instrumental neutron activation analysis (INAA) technique was used to measure the concentrations of various trace elements in nail polishes of popular Indian and foreign brands. The aim of the present experiment was to see whether trace elements could distinguish nail polishes of different Indian and foreign brands from forensic point of view. It was found that cesium can act as a marker to differentiate foreign and Indian brands. (author)

  7. Interlocking directorships in Polish joint stock companies:

    OpenAIRE

    Pawlak, Marek

    2008-01-01

    Studies concerning interlocking directorships have been carried out among Polish joint stock corporations. The main source of data have been the announcements that are to be published by corporations regularly in a journal called Business and Court Gazette (BCG). Interlocking directorships constitute a network among corporations the use of which enables co-ordinated management of the whole group. The phenomenon of interlocking directorships in Polish joint stock companies can be compared to t...

  8. Jewish problem in the Polish Communist Party

    Directory of Open Access Journals (Sweden)

    Cimek Henryk

    2016-12-01

    Full Text Available Jews accounted for approx. 8-10% of the population of the Second Republic and in the communist movement (Polish Communist Party and Polish Communist Youth Union the rate was approx, 30%, while in subsequent years it much fluctuated. The percentage of Jews was the highest in the authorities of the party and in the KZMP. This had a negative impact on the position of the KPP on many issues, especially in its relation to the Second Republic.

  9. Attack polish for nickel-base alloys and stainless steels

    Science.gov (United States)

    Not Available

    1980-05-28

    A chemical attack polish and polishing procedure for use on metal surfaces such as nickel base alloys and stainless steels is described. The chemical attack polich comprises FeNO/sub 3/, concentrated CH/sub 3/COOH, concentrated H/sub 2/SO/sub 4/ and H/sub 2/O. The polishing procedure includes saturating a polishing cloth with the chemical attack polish and submicron abrasive particles and buffing the metal surface.

  10. Experimental Polish-Lithuanian Corpus with the Semantic Annotation Elements

    Directory of Open Access Journals (Sweden)

    Danuta Roszko

    2015-06-01

    Full Text Available Experimental Polish-Lithuanian Corpus with the Semantic Annotation Elements In the article the authors present the experimental Polish-Lithuanian corpus (ECorpPL-LT formed for the idea of Polish-Lithuanian theoretical contrastive studies, a Polish-Lithuanian electronic dictionary, and as help for a sworn translator. The semantic annotation being brought into ECorpPL-LT is extremely useful in Polish-Lithuanian contrastive studies, and also proves helpful in translation work.

  11. Conformal polishing approach: Tool footprint analysis

    Directory of Open Access Journals (Sweden)

    José A Dieste

    2016-02-01

    Full Text Available Polishing process is one of the most critical manufacturing processes during a metal part production because it determines the final quality of the product. Free-form surface polishing is a handmade process with lots of rejected parts, scrap generation and time and energy consumption. Two different research lines are being developed: prediction models of the final surface quality parameters and an analysis of the amount of material removed depending on the polishing parameters to predict the tool footprint during the polishing task. This research lays the foundations for a future automatic conformal polishing system. It is based on rotational and translational tool with dry abrasive in the front mounted at the end of a robot. A tool to part concept is used, useful for large or heavy workpieces. Results are applied on different curved parts typically used in tooling industry, aeronautics or automotive. A mathematical model has been developed to predict the amount of material removed in function of polishing parameters. Model has been fitted for different abrasives and raw materials. Results have shown deviations under 20% that implies a reliable and controllable process. Smaller amount of material can be removed in controlled areas of a three-dimensional workpiece.

  12. Laser polishing of additive manufactured Ti alloys

    Science.gov (United States)

    Ma, C. P.; Guan, Y. C.; Zhou, W.

    2017-06-01

    Laser-based additive manufacturing has attracted much attention as a promising 3D printing method for metallic components in recent years. However, surface roughness of additive manufactured components has been considered as a challenge to achieve high performance. In this work, we demonstrate the capability of fiber laser in polishing rough surface of additive manufactured Ti-based alloys as Ti-6Al-4V and TC11. Both as-received surface and laser-polished surfaces as well as cross-section subsurfaces were analyzed carefully by White-Light Interference, Confocal Microscope, Focus Ion Beam, Scanning Electron Microscopy, Energy Dispersive Spectrometer, and X-ray Diffraction. Results revealed that as-received Ti-based alloys with surface roughness more than 5 μm could be reduce to less than 1 μm through laser polishing process. Moreover, microstructure, microhardness and wear resistance of laser-polished zone was investigated in order to examine the thermal effect of laser polishing processing on the substrate of additive manufactured Ti alloys. This proof-of-concept process has the potential to effectively improve the surface roughness of additive manufactured metallic alloy by local polishing method without damage to the substrate.

  13. Interculutral Polish-Chinese QQing

    Directory of Open Access Journals (Sweden)

    Elżbieta Gajek

    2012-12-01

    Full Text Available Working in tandem with the use of information and communication technologies is well-known and frequently used as a method of supporting learning of foreign languages in authentic communication. It is based on a constructivist approach to teaching. In the reported case study Polish and Chinese students discussed in English preprepared topics. The work shows the potential of e-learning at the micro level, as the language and intercultural task is implemented into an academic course without modification of the objectives and learning outcomes of the course. Evaluation carried out at the end of the project indicates that both groups perceived the task as a significant linguistic, cultural and personal experience. They stressed the importance of sharing “culture for culture” as the partner culture was new for most of them. The ability to talk and respond to information which was often strange, from the point of view of their own culture, allowed for learning intercultural competence ̔in action’.

  14. Evaluation of the effects of coal grinding in terms of coal water slurry preparation

    Directory of Open Access Journals (Sweden)

    Robak Jolanta

    2016-01-01

    Full Text Available Coal Water Slurry (CWS is a specific form of solid fuel. It occurs in the form of finely ground coal particles and water. Depending on the use, the content of combustible matter is from 40 to 70% by weight. The attractiveness of the fuel is primarily its properties, i.e. liquid form, high energy efficiency (for water evaporation 4% energy is used – for CSW with 70% concentration of coal, decreased environmental impurities (lower NOx emission and reduced risk of explosion. The advantages of CWS fuels, the possibility of independence from petrochemical fuels, wide availability of coal and emphasis on the use of cleaner technologies are the driving force for development of slurry fuel technologies. The major parameters characterizing the fuel suspension are: solid phase concentration (share of coal in the slurry expressed as either weight or volume fraction of dry coal, time stability (resistance to delamination and separation of the dispersed phase from the continuous phase and viscosity, determining the flow of suspension. The mentioned parameters are dependent on the susceptibility of coal for production of aqueous suspensions (slurrability, conditioned by natural properties of coal, such as: coalification degree, petrographic composition and surface properties. They are also dependent on the slurry fuel preparation process: particle size, solid phase concentration, used additives (stabilizing and dispersion agents and modification of primary coal properties (ash removal, change of surface properties. Preparation of sustainable, high concentrated CWS fuel coal is promoted by the hydrophobic nature of the coal surface, characteristic for coals of higher coalification. A great technological problem is to obtain a highly concentrated coal slurry fuel from less coalified hydrophilic steam coals. The paper presents the results of lab scale research on the CWS prepared from Polish steam coal by wet grinding in mill drum and vibrating. The milling

  15. Effects of torpedo blasting on rockburst prevention during deep coal seam mining in the Upper Silesian Coal Basin

    Directory of Open Access Journals (Sweden)

    Ł. Wojtecki

    2017-08-01

    Full Text Available In the Upper Silesian Coal Basin (USCB, coal seams are exploited under progressively more difficult geological and mining conditions (greater depth, higher horizontal stress, more frequent occurrence of competent rock layers, etc.. Mining depth, dislocations and mining remnants in coal seams are the most important factors responsible for the occurrence of rockburst hazards. Longwall mining next to the mining edges of neighbouring coal seams is particularly disadvantageous. The levels of rockburst hazards are minimised via the use of rockburst prevention methods. One active prevention method is torpedo blasting in roof rocks. Torpedo blastings are performed in order to decrease local stress concentrations in rock masses and to fracture the roof rocks to prevent or minimise the impact of high-energy tremors on excavations. The estimation of the effectiveness of torpedo blasting is particularly important when mining is under difficult geological and mining conditions. Torpedo blasting is the main form of active rockburst prevention in the assigned colliery in the Polish part of the USCB. The effectiveness of blasting can be estimated using the seismic effect method, in which the seismic monitoring data and the mass of explosives are taken into consideration. The seismic effect method was developed in the Czech Republic and is always being used in collieries in the Czech part of the coal basin. Now, this method has been widely adopted for our selected colliery in the Polish part of the coal basin. The effectiveness of torpedo blastings in the faces and galleries of the assigned longwall in coal seam 506 has been estimated. The results show that the effectiveness of torpedo blastings for this longwall was significant in light of the seismic effect method, which corresponds to the in situ observations. The seismic effect method is regularly applied to estimating the blasting effectiveness in the selected colliery.

  16. Engineering Graphene Films from Coal

    Science.gov (United States)

    Vijapur, Santosh H.

    Graphene is a unique material with remarkable properties suitable for a wide array of applications. Chemical vapor deposition (CVD) is a simple technique for synthesis of large area and high quality graphene films on various metal substrates. Among the metal substrates, copper has been shown to be an excellent support for the growth of graphene films. Traditionally, hydrocarbon gases are used for the graphene synthesis via CVD. Unconventional solid carbon sources such as various polymers and food waste have also shown great potential for synthesis of graphene films. Coal is one such carbon enriched and abundantly available unconventional source. Utilization of coal as a carbon source to synthesize large area, transparent, and high quality few-layer graphene films via CVD has been demonstrated in the present work. Hydrocarbon gases are released as products of coal pyrolysis at temperatures ≥400 °C. This study hypothesized that, these hydrocarbon gases act as precursors for the synthesis of graphene films on the copper substrate. Hence, atmospheric pressure CVD and low temperature of 400 °C were utilized initially for the production of graphene films. These conditions were suitable for the formation of amorphous carbon (a-C) films but not crystalline graphene films that were the objective of this work. The synthesized a-C films on the copper substrate were shown to be uniform and transparent with large surface area. The thickness and surface roughness of the a-C films were determined to have typical values of 5 nm and 0.55 nm, respectively. The a-C film has >95 % optical transmittance and sheet resistivity of 0.6 MO sq-1. These values are comparable to other carbon thin films synthesized at higher temperatures. Further, the a-C films were transferred onto any type of substrate such as silicon wafer and titanium foil, and can be utilized for diverse applications. However, crystalline graphene films were not produced by implementing atmospheric pressure CVD and low

  17. Assessment of the content of arsenic in solid by-products from coal combustion

    OpenAIRE

    Wierońska Faustyna; Makowska Dorota; Strugała Andrzej

    2017-01-01

    The coal combustion processes constitute one of the major sources of heavy metals emission into the atmosphere. From the point of view of the reduction of the emission of heavy metals and the selection of the correct exhaust gas treatment system, it is important to monitor the amount of trace elements in the solid fuels and in the solid by-products from coal combustion. One of these highly toxic elements is arsenic. The average content of arsenic in Polish hard coals and lignites is 0 ÷ 40 mg...

  18. Materials of 45. Scientific Assembly of Polish Chemical Society. Volumes 1-3

    International Nuclear Information System (INIS)

    2002-01-01

    Scientific assemblies of Polish Chemical Society are the most important chemical meeting organised annually in Poland. Basic as well as application studies in all chemical branches have been extensively presented. The next subjects was proposed as scientific sessions and symposia topics: organic chemistry, inorganic chemistry, physical chemistry, analytical chemistry, technology and chemical engineering, polymer chemistry, solid state chemistry, catalysis, biological chemistry, chemistry and technology of coal, environmental protection, didactics of chemistry, history of chemistry, young scientist forum, flow analysis, and high-energy materials

  19. Synthesis and characterization of zeolite from coal ashes modified by cationic surfactant; Sintese e caracterizacao de zeolita de cinzas de carvao modificada por surfactante cationico

    Energy Technology Data Exchange (ETDEWEB)

    Fungaro, D.A.; Borrely, S.I., E-mail: dfungaro@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2012-01-15

    Zeolite synthesized from coal fly ash was modified with different concentrations (2 and 20 mmol.L{sup -1}) of hexadecyltrimethylammonium bromide (HDTMA-Br). The Non-Modified Zeolite (NMZ) and Surfactant-Modified Zeolites (SMZ) were characterized by X-ray fluorescence spectrometry, X-ray diffraction, Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy, thermogravimetric analysis, among others. The SMS presented negative charge probably due to the formation of a partial bilayer of HDTMA on exchangeable active sites on the external surface of NMZ. A decrease in surface area was observed for SMZ as compared to NMZ indicating zeolite surface coverage with HDTMA-Br molecules. The crystalline nature of the zeolite remained intact after adsorption of surfactant and heating for drying. FTIR analysis indicated that there were no significant changes in the structure of the zeolite after adsorption of surfactant. (author)

  20. Soft-chemical synthesis and catalytic activity of Ni-Al and Co-Al layered double hydroxides (LDHs intercalated with anions with different charge density

    Directory of Open Access Journals (Sweden)

    Takahiro Takei

    2014-09-01

    Full Text Available Co-Al and Ni-Al layered double hydroxides (LDHs intercalated with three types of anionic molecules, dodecylsulfate (C12H25SO4−, DS, di-2-ethylsulfosuccinate ([COOC2H3EtBu]2C2H3SO3−, D2ES, and polytungstate (H2W12O4210−, HWO were prepared by means of ion-exchange and co-precipitation processes. With the use of DS and D2ES as intercalation agents, high crystallinity was maintained after intercalation into the LDHs. In the case of HWO, the intercalated LDHs could be obtained by ion-exchange as well as co-precipitation with a decline in the crystallinity; however, unreacted LDH was detected in the ion-exchange samples, and some unwanted phases such as hydroxide and pyrochlore were generated by the co-precipitation process. The maximum specific surface area and pore volume of the Ni-Al sample with intercalated HWO, prepared by the ion-exchange process were 74 m2/g and 0.174 mL/g, respectively. The occupancies of DS, D2ES, and HWO within the interlayer space were approximately 0.3–0.4, 0.5–0.6, and 0.1–0.2, respectively, in the Co-Al and Ni-Al LDHs. Analysis of the catalytic activity demonstrated that the DS-intercalated Ni-Al LDH sample exhibited relatively good catalytic activity for conversion of cyclohexanol to cyclohexanone.

  1. Coal information 1996

    International Nuclear Information System (INIS)

    1997-01-01

    Coal Information (1997 edition) is the latest edition of a publication that has been produced annually by the IEA since 1983. The report is intended to provide both Member countries of the OECD and those employed in all sectors of the coal industry with information on current world coal market trends and long-term prospects. It includes information on coal prices, demand, trade, supply, production capacity, transport, environmental issues (including emission standards for coal-fired boilers), coal ports, coal-fired power stations and coal used in non -OECD countries. Part I of the publication contains a wide ranging review of world coal market developments in 1996 and current prospects to 2010. The review is based on historical data of OECD energy supply and demand, data on other world regions, projections of OECD coal supply, demand and trade and information provided by the CIAB. Part II provides, in tabular and graphical form, a more detailed and comprehensive statistical picture of coal developments and future prospects for coal in the OECD, by region and for individual Member countries. Readers interested in projections are strongly advised to read the notes for individual countries in Principles and Definitions in Part II. Coal statistics for non-OECD countries are presented in Part III of the book. Summary data are available on hard coal supply and end-use statistics for about 40 countries and regions world-wide. Data are based on official national submissions to the United Nations in Geneva and New York, national energy publications, information provided to the IEA Secretariat by national statistical offices as well as other unofficial Secretariat sources. Further information on coal used in non-OECD countries is published annually by the IEA in Energy Statistics and Balances of Non-OECD Countries. Also included in Part III are the Survey of Coal Ports world-wide and the Survey of Coal-fired Power Stations in coal-importing countries

  2. Work Engagement – A Systematic Review of Polish Research

    Directory of Open Access Journals (Sweden)

    Pollak Anita

    2017-06-01

    Full Text Available Over the past decade work engagement has gained both business and academia attention. With growing number of studies and meta-analyses the concept of work engagement is one of the pillars of positive work and organizational psychology. This systematic review presents the current state of research on work engagement in Poland. Results confirmed that work-engagement studies have not yet reached the threshold to conduct meta-analysis. The review of measurement methods and synthesis of findings allows to identify strengths and gaps in Polish studies. Discussion of limitations and biases in current research is accompanied with urge to overcome them and develop thriving stream of research on work engagement.

  3. Polishing for glass ceramics: which protocol?

    Science.gov (United States)

    Silva, Tânia Mara da; Salvia, Ana Carolina Rodrigues Danzi; Carvalho, Rodrigo Furtado de; Pagani, Clovis; Rocha, Daniel Maranha da; Silva, Eduardo Galera da

    2014-07-01

    The execution of adjustments on ceramic restorations is sometimes necessary for either correction of occlusion and/or inadequate contours or esthetical improvements. Clinically, the surfaces undergo weariness through fine grinding diamond burs which remove the superficial glazing layer. Several materials for ceramic polishing have been used in an attempt to reach a satisfactory surface smoothness. The aim of this study was to perform a literature review on different polishing protocols of several dental ceramics. This is a literature review performed through scientific articles published between 2004 and 2012, indexed in MEDLINE, PubMed and Scielo databases. The study selected and analyzed a total of 20 relevant articles that evaluated different types of ceramics, polishing treatment and surface roughness. After an extensive literature review, this study observed: 1 - after the rupture of the glazing layer due to the adjustments of the restorations, the best choice for the polishing of the surface will depend on the type of ceramics used; 2 - glazing procedure provide excellent results regarding to the superficial smoothness; however, if reglazing is impossible, either abrasive rubber cups/points or sandpaper discs followed by the use of diamond polishing pastes results in a satisfactory superficial smoothness; 3 - clinical studies that take into account the behavior of the protocols polishing are scarce and should be encouraged; 4 - the large number of variables influence the final outcome of polishing should be considered. The necessity in standardization of methodologies to enable a comparison among researches. Copyright © 2014 Japan Prosthodontic Society. Published by Elsevier Ltd. All rights reserved.

  4. Smoking characteristics of Polish immigrants in Dublin.

    LENUS (Irish Health Repository)

    Kabir, Zubair

    2008-01-01

    BACKGROUND: This study examined two main hypotheses: a) Polish immigrants\\' smoking estimates are greater than their Irish counterparts (b) Polish immigrants purchasing cigarettes from Poland smoke "heavier" (>\\/= 20 cigarettes a day) when compared to those purchasing cigarettes from Ireland. The study also set out to identify significant predictors of \\'current\\' smoking (some days and everyday) among the Polish immigrants. METHODS: Dublin residents of Polish origin (n = 1,545) completed a previously validated Polish questionnaire in response to an advertisement in a local Polish lifestyle magazine over 5 weekends (July-August, 2007). The Office of Tobacco Control telephone-based monthly survey data were analyzed for the Irish population in Dublin for the same period (n = 484). RESULTS: Age-sex adjusted smoking estimates were: 47.6% (95% Confidence Interval [CI]: 47.3%; 48.0%) among the Poles and 27.8% (95% CI: 27.2%; 28.4%) among the general Irish population (p < 0.001). Of the 57% of smokers (n = 345\\/606) who purchased cigarettes solely from Poland and the 33% (n = 198\\/606) who purchased only from Ireland, 42.6% (n = 147\\/345) and 41.4% (n = 82\\/198) were "heavy" smokers, respectively (p = 0.79). Employment (Odds Ratio [OR]: 2.89; 95% CI: 1.25-6.69), lower education (OR: 3.76; 95%CI: 2.46-5.74), and a longer stay in Ireland (>24 months) were significant predictors of current smoking among the Poles. An objective validation of the self-reported smoking history of a randomly selected sub-sample immigrant group, using expired carbon monoxide (CO) measurements, showed a highly significant correlation coefficient (r = 0.64) of expired CO levels with the reported number of cigarettes consumed (p < 0.0001). CONCLUSION: Polish immigrants\\' smoking estimates are higher than their Irish counterparts, and particularly if employed, with only primary-level education, and are overseas >2 years.

  5. Gasification of various types of tertiary coals: A sustainability approach

    International Nuclear Information System (INIS)

    Öztürk, Murat; Özek, Nuri; Yüksel, Yunus Emre

    2012-01-01

    Highlights: ► Production energy by burning of coals including high rate of ash and sulfur is harmful to environment. ► Energy production via coal gasification instead of burning is proposed for sustainable approach. ► We calculate exergy and environmental destruction factor of gasification of some tertiary coals. ► Sustainability index, improvement potential of gasification are evaluated for exergy-based approach. - Abstract: The utilization of coal to produce a syngas via gasification processes is becoming a sustainability option because of the availability and the economic relevance of this fossil source in the present world energy scenario. Reserves of coal are abundant and more geographically spread over the world than crude oil and natural gas. This paper focuses on sustainability of the process of coal gasification; where the synthesis gas may subsequently be used for the production of electricity, fuels and chemicals. The coal gasifier unit is one of the least efficient step in the whole coal gasification process and sustainability analysis of the coal gasifier alone can substantially contribute to the efficiency improvement of this process. In order to evaluate sustainability of the coal gasification process energy efficiency, exergy based efficiency, exergy destruction factor, environmental destruction factor, sustainability index and improvement potential are proposed in this paper.

  6. International perspectives on coal preparation

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-31

    The report consists of the vugraphs from the presentations which covered the following topics: Summaries of the US Department of Energy`s coal preparation research programs; Preparation trends in Russia; South African coal preparation developments; Trends in hard coal preparation in Germany; Application of coal preparation technology to oil sands extraction; Developments in coal preparation in China; and Coal preparation in Australia.

  7. APS 3D: a new benchmark in aspherical polishing

    Science.gov (United States)

    Gauch, Daniel; Mikulic, Dalibor; Veit, Christian

    2017-10-01

    The APS 3D system performs polishing and form correction in one step in order to reduce overall process time, reduce the number of polishing steps required and eliminate the need for highly skilled operators while providing a repeatable polishing process. This new 3D Polishing system yields better surface quality, and a better slope error, automatically determining the optimum speeds, feed rates and polish pressures to achieve a deterministic process based on the required quality parameters input by the operator. The process flow is always the same to ensure consistent quality and target quality values are defined before polishing begins.

  8. Measurement of reflectance of coal macerals: its automation and significance

    Energy Technology Data Exchange (ETDEWEB)

    Davis, A.

    1978-06-01

    A prime objective of the Pennsylvania State University's DOE program is the characterization of 1,300 samples of U.S. coals. Reflectance determination plays a major role in meeting this objective, because it is used as an accurate rank index both to select coals for testing and to investigate property-behavior interrelationships using the Penn State/DOE Coal Data Base. Reflectances of coal macerals are related to their refractive and absorptive indices by the Beer equation; the refractive index of the medium and the wavelength of light need to be specified. Determinations usually are made in immersion oil at 546 nm. Properties of vitrinite make it the most suitable maceral for these measurements, but the variety of vitrinite selected may depend upon the intended application. Vitrinite reflectance is considered to be dependent upon the degree of aromatization of its structural units. Although some of the earlier investigators believed that the reflectance of coals increased in a discontinuous, stepped manner as their rank increased, the bulk of assembled data suggests that the change is continuous. Some recent results indicate that there may be more than one coalification track for coals with different geological histories, resulting in displacement from the general trend. Several techniques have been employed to determine the optical properties of coal constituents. Usual comparative method involves the use of a microscope photometer to compare the intensity of light reflected by particles within a polished pellet of coal to that of a glass or synthetic mineral standard. Because coal is anisotropic it is common to measure either maximum reflectance in polarized light or random reflectance in non-polarized light. Various eqipment modifications and accessories have been used to improve the ease of measuring maximum reflectance.

  9. The analysis of mercury content in coals and ashes

    Directory of Open Access Journals (Sweden)

    Kasprzyk Marta

    2017-01-01

    Full Text Available It is well known that mercury that enters the atmosphere is a serious threat to the natural environment. From the available literature, it can be stated that fossil fuels are among the main carriers of this fuel. The question arises whether it is the right approach. While the enrichment of bituminous coal produces limited amounts of mercury, they are being released into the atmosphere as a result of the combustion of coal. The situation is similar in the case of biomass, which releases large amounts of mercury into the atmosphere when subjected to the combustion process. While bituminous coal is the carrier of mercury, the application of currently known technology, rational production and the use of fossil fuels make it possible to maximally minimize mercury emissions into the atmosphere. This study evaluated the mercury content in the ashes resulting from the combustion of bituminous coal subjected to the enrichment process. The samples were collected from ten mines located in the Polish part of the Upper Silesian Coal Basin (USCB. In total, thirty coal samples and thirty products of the combustion process were examined. All sixty samples were subjected to physicochemical analysis, including: moisture content, ash content, sulfur content, carbon content, and Gross Calorific Value.

  10. Permeability changes in coal resulting from gas desorption

    Energy Technology Data Exchange (ETDEWEB)

    Levine, J.R.; Johnson, P.W.

    1992-11-30

    This report documents studies on the effects of gas sorption on coal, with the intent of eventually evaluating how sorption and strain affect permeability. These studies were, carried out at the University of Alabama during the period from 1989 through 1992. Two major experimental methods were developed and used. In the strain experiments, electronic strain gauges were attached to polished blocks of coal in order to measure linear and volumetric swelling due to gas sorption. The effects of bedding plane orientation, of gas type, and of coal type were investigated. In the gravimetric experiment the weight of small samples of coal was measured during exposure to high pressure gases. Sample measurements were corrected for buoyancy effects and for sample swelling, and the results were plotted in the form of Langmuir isotherms. Experiments were conducted to determine the effect of grain size, coal type, moisture, and of sorbant gas. The advantage of this method is that it can be applied to very small samples, and it enabled comparison liptinite versus vitrinite concentrates, and kerogen rich versus kerogen depleted oil shales. Also included is a detailed discussion of the makeup of coal and its effect on gas sorption behavior.

  11. Permeability changes in coal resulting from gas desorption. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Levine, J.R.; Johnson, P.W.

    1992-11-30

    This report documents studies on the effects of gas sorption on coal, with the intent of eventually evaluating how sorption and strain affect permeability. These studies were, carried out at the University of Alabama during the period from 1989 through 1992. Two major experimental methods were developed and used. In the strain experiments, electronic strain gauges were attached to polished blocks of coal in order to measure linear and volumetric swelling due to gas sorption. The effects of bedding plane orientation, of gas type, and of coal type were investigated. In the gravimetric experiment the weight of small samples of coal was measured during exposure to high pressure gases. Sample measurements were corrected for buoyancy effects and for sample swelling, and the results were plotted in the form of Langmuir isotherms. Experiments were conducted to determine the effect of grain size, coal type, moisture, and of sorbant gas. The advantage of this method is that it can be applied to very small samples, and it enabled comparison liptinite versus vitrinite concentrates, and kerogen rich versus kerogen depleted oil shales. Also included is a detailed discussion of the makeup of coal and its effect on gas sorption behavior.

  12. Inorganic Constituents in Coal

    Directory of Open Access Journals (Sweden)

    Rađenović A.

    2006-02-01

    Full Text Available Coal contains not only organic matter but also small amounts of inorganic constituents. More thanone hundred different minerals and virtually every element in the periodic table have been foundin coal. Commonly found group minerals in coal are: major (quartz, pyrite, clays and carbonates,minor, and trace minerals. Coal includes a lot of elements of low mass fraction of the orderof w=0.01 or 0.001 %. They are trace elements connected with organic matter or minerals comprisedin coal. The fractions of trace elements usually decrease when the rank of coal increases.Fractions of the inorganic elements are different, depending on the coal bed and basin. A varietyof analytical methods and techniques can be used to determine the mass fractions, mode ofoccurrence, and distribution of organic constituents in coal. There are many different instrumentalmethods for analysis of coal and coal products but atomic absorption spectroscopy – AAS is theone most commonly used. Fraction and mode of occurrence are one of the main factors that haveinfluence on transformation and separation of inorganic constituents during coal conversion.Coal, as an important world energy source and component for non-fuels usage, will be continuouslyand widely used in the future due to its relatively abundant reserves. However, there is aconflict between the requirements for increased use of coal on the one hand and less pollution onthe other. It’s known that the environmental impacts, due to either coal mining or coal usage, canbe: air, water and land pollution. Although, minor components, inorganic constituents can exert asignificant influence on the economic value, utilization, and environmental impact of the coal.

  13. Flash hydrogenation of coal

    Science.gov (United States)

    Manowitz, Bernard; Steinberg, Meyer; Sheehan, Thomas V.; Winsche, Warren E.; Raseman, Chad J.

    1976-01-01

    A process for the hydrogenation of coal comprising the contacting of powdered coal with hydrogen in a rotating fluidized bed reactor. A rotating fluidized bed reactor suitable for use in this process is also disclosed. The coal residence time in the reactor is limited to less than 5 seconds while the hydrogen contact time is not in excess of 0.2 seconds.

  14. Material removal mechanisms in abrasive vibration polishing of complex molds

    Science.gov (United States)

    Brinksmeier, E.; Riemer, O.; Schulte, H.

    2010-10-01

    Optical and medical industries are demanding a large variety of optical elements exhibiting complex geometries and multitude opto-functional areas in the range of a few millimeters [1]. Therefore, mold inserts made of steel or carbides must be finished by polishing for the replication of glass and plastic lenses [2]. For polishing theses complex components in the shape of localized cavities or grooves the application of rotating polishing pads is very limited. Established polishing processes are not applicable, so state of the art is a time consuming and therefore expensive polishing procedures by hand. An automated process with conventional polishing machines is impossible because of the complex mold insert geometry. The authors will present the development of a new abrasive polishing process for finishing these complex mold geometries to optical quality. The necessary relative velocity in the contact area between polishing pad and workpiece surface is exclusively realized by vibration motions which is an advantage over vibration assisted rotating polishing processes. The absence of rotation of the pad opens up the possibility to machine new types of surface geometries. The specific influence factors of vibration polishing were analyzed and will be presented. The determination of material removal behavior and polishing effect on planar steel samples has shown that the conventional abrasive polishing hypothesis of Preston is applicable to the novel vibration polishing process. No overlaid chemical material removal appears.

  15. Polish Academy of Sciences Great Dictionary of Polish [Wielki słownik języka polskiego PAN

    Directory of Open Access Journals (Sweden)

    Piotr Žmigrodzki

    2014-12-01

    Full Text Available The paper describes a lexicographical project involving the development of the newest general dictionary of the Polish language: the Polish Academy of Sciences Great Dictionary of Polish [Wielki słownik języka polskiego PAN]. The project is coordinated by the Institute of Polish Language at the Polish Academy of Sciences and carried out in collaboration with linguists and lexicographers from several other Polish academic centres. The paper offers a brief description of the genesis of the project and the scope of information included in the dictionary, the organisation of work, the life of the dictionary on the Web as well as the plans for the future.

  16. Using proximate analysis to characterize airborne dust generation from bituminous coals

    Energy Technology Data Exchange (ETDEWEB)

    Page, S.J.; Organiscak, J.A. [NIOSH, Pittsburgh, PA (United States). Pittsburgh Research Lab.

    2002-06-01

    Laboratory crushing experiments were conducted on a range of low to high volatile bituminous coals to investigate the various factors influencing airborne respirable dust generation. Bituminous coal samples from 8 mines (5 U.S. and 3 Polish) were uniformly prepared and processed through a double roll crusher located in a low air velocity wind tunnel. Experimental factors studied included inherent coal seam constituents, specific energy of crushing, product size characteristics, dust cloud electrostatic field, and specific quantity of airborne respirable dust generated. A combination of factors is associated with the generation of airborne respirable dust. One factor involved is the effect of coal rank, described by the inherent moist fuel ratio, on the product size characteristics. However, since coals of high moist fuel ratio (high rank) are generally more extensively cleated, it is suggested that the degree of cleating is directly responsible for the quantity of respirable-sized particles produced in the crushed product material for eastern U.S. coals. This is implied by the relationship of ash content and at least one mineral constituent (pyrite, determined from pyritic sulfur analysis) to the percentage of airborne respirable dust. A clear delineation of coals, based on well-known proximate analysis characteristics, that generate the most respirable dust appears to be possible. It was also shown that the dust-generating characteristics of coals could be reasonably described by both the moist fuel ratio and the Hardgrove Grindability Index (HGI). These results show a clear distinction between eastern and western U.S. coals. However, no consistent distinction for Polish coal was observed.

  17. Surface Roughness and Gloss of Actual Composites as Polished With Different Polishing Systems.

    Science.gov (United States)

    Rodrigues-Junior, S A; Chemin, P; Piaia, P P; Ferracane, J L

    2015-01-01

    This in vitro study evaluated the effect of polishing with different polishing systems on the surface roughness and gloss of commercial composites. One hundred disk-shaped specimens (10 mm in diameter × 2 mm thick) were made with Filtek P-90, Filtek Z350 XT, Opallis, and Grandio. The specimens were manually finished with #400 sandpaper and polished by a single operator using three multistep systems (Superfix, Diamond Pro, and Sof-lex), one two-step system (Polidores DFL), and one one-step system (Enhance), following the manufacturer's instructions. The average surface roughness (μm) was measured with a surface profilometer (TR 200 Surface Roughness Tester), and gloss was measured using a small-area glossmeter (Novo-Curve, Rhopoint Instrumentation, East Sussex, UK). Data were analyzed by two-way analysis of variance and Tukey's test (α=0.05). Statistically significant differences in surface roughness were identified by varying the polishing systems (pGrandio when polished with Sof-Lex and Filtek Z250 and Opallis when polished with Enhance. Gloss was influenced by the composites (p<0.0001), the polishing systems (p<0.0001), and the interaction between them (p<0.0001). The one-step system, Enhance, produced the lowest gloss for all composites. Surface roughness and gloss were affected by composites and polishing systems. The interaction between both also influenced these surface characteristics, meaning that a single polishing system will not behave similarly for all composites. The multistep systems produced higher gloss, while the one-step system produced the highest surface roughness and the lowest gloss of all.

  18. [Bogdan Suchodolski--initiator and editor-in-chief of the publication History of Polish Science].

    Science.gov (United States)

    Kuźnicka, Barbara; Kuźnicki, Leszek

    2011-01-01

    Among numerous and distinguished author's and editorial works of Bogdan Suchodolski a particular value presents a publication in eight volumes entitled 'History of Polish Science' (including two biographical and bibliographic volumes), which was published in the years 1970-1992 on Professor's own initiative and edited by himself. This is the first synthesis of the history of science in Poland, from the beginning of the Middle Ages till the present time (to 1952). In the conception of the initiator and editor the work presents the development of scientific thought and achievements of the scholars in relation to national culture and in connexions with the trends in science in the world. 'History of Polish Science' is the work written by several dozen authors, representing different domains of the knowledge. Scientific, organizational and editorial patronate was possible by dint of History of Science and Technology Establishment of Polish Academy of Sciences (presently the Institute for the History of Science of Polish Academy of Sciences), which was managed by Bogdan Suchodolski.

  19. Lead extraction and glass-ceramics synthesis from waste cathode ray tube funnel glass through cooperative smelting process with coal fly ash.

    Science.gov (United States)

    Lv, Jianfang; Yang, Hongying; Jin, Zhenan; Zhao, Minglei

    2018-03-14

    In this study, a novel process was developed for extracting lead from the hazardous waste cathode ray tube (CRT) funnel glass and simultaneously producing glass-ceramics. CRT funnel glass was mixed with coal fly ash and subjected to carbon thermal reduction with the addition of CaO. The homogeneous glass melt and reduced metallic lead were quenched in water. Glass-ceramics were produced from the parent glass through an appropriate heat treatment. The optimum carbon loading amount (calculated as the molar ratio of C/PbO), CaO/SiO 2 ratio, smelting temperature and holding time for lead recovery were 1.0, 0.3-0.6, 1450 °C and 2 h, respectively. Under these conditions, more than 95% of lead can be extracted from the funnel glass and a low lead content of the resultant parent glass below 0.6 wt% was successfully achieved. CaO behaved as a network modifier to reduce the viscosity of the glass and also acted as a substitution to release lead oxide from the silicate network structure, resulting in a high lead separation efficiency. X-ray diffraction (XRD) analysis revealed that the main crystalline phase was gehlenite when 50-70 wt% funnel glass was added. Scanning electron microscopy (SEM) observation showed that well-crystallized crystals occurred in the specimens with 50-70 wt% funnel glass additions, whereas the specimens with 40 wt% and 80 wt% glass additions exhibited a relative low crystallization degree. Furthermore, property measurements, chemical resistance tests and leaching characteristics of heavy metals confirmed the possibility of engineering and construction applications of the superior glass-ceramic products. Overall results indicate that the process proposed in this paper is an effective and promising approach for reutilization of obsolete CRT funnel glass. Copyright © 2018 Elsevier Ltd. All rights reserved.

  20. Self-scrubbing coal

    International Nuclear Information System (INIS)

    Kindig, J.K.

    1992-01-01

    More than 502 million tons - 65 percent of all coal shipped to utilities in 1990 - were above 1.2 pounds of sulfur dioxide per million Btu. Most of the coal, even though cleaned in conventional coal preparation plants, still does not meet the emission limitation the Clean Air Act Amendments mandate for the year 2000. To cope with this fact, most utilities plan to switch to low sulfur (western U.S. or Central Appalachian) coal or install scrubbers. Both solutions have serous drawbacks. Switching puts local miners out of work and weakens the economy in the utility's service territory. Scrubbing requires a major capital expenditure by the utility. Scrubbers also increase the operating complexity and costs of the generating station and produce yet another environmental problem, scrubber sludge. Employing three new cost-effective technologies developed by Customer Coals International (CCl), most non-compliance coals east of the Mississippi River can be brought into year-2000 compliance. The compliance approach employed, depends upon the characteristics of the raw coal. Three types of raw coal are differentiated, based upon the amount of organic sulfur in the coals and the ease (or difficultly) of liberating the pyrite. They are: Low organic sulfur content and pyrite that liberates easily. Moderate organic sulfur content and pyrite that liberates easily. High organic sulfur content or the pyrite liberates with difficulty. In this paper examples of each type of raw coal are presented below, and the compliance approach employed for each is described. The names of the beneficiated coal products produced from each type of raw coal give above are: Carefree Coal, Self-Scrubbing Coal and Dry-Scrubbing Coal

  1. Australian Coal Company Risk Factors: Coal and Oil Prices

    OpenAIRE

    M. Zahid Hasan; Ronald A. Ratti

    2014-01-01

    Examination of panel data on listed coal companies on the Australian exchange over January 1999 to February 2010 suggests that market return, interest rate premium, foreign exchange rate risk, and coal price returns are statistically significant in determining the excess return on coal companies’ stock. Coal price return and oil price return increases have statistically significant positive effects on coal company stock returns. A one per cent rise in coal price raises coal company returns ...

  2. A blocked takeover in the Polish power sector: A model-based analysis

    International Nuclear Information System (INIS)

    Kamiński, Jacek

    2014-01-01

    As the President of the Office of Competition and Consumer Protection refused to approve a government initiated takeover in the Polish power sector and the Court of Competition and Consumer Protection did not make a ruling on that case, the takeover was finally prohibited. In this context, the main aim of this paper is to carry out a quantitative analysis of the impact of the takeover in question on electricity prices and quantities, consumer and producer surpluses, dead weight loss and emissions. The scope of the study covers the Polish power generation sector and the analysis was carried out for 2009. A game theory-based electricity market equilibrium model developed for Poland was applied. The model includes several country-specific conditions, such as a coal-based power generation fuel-mix, a large share of biomass co-combustion, etc. For the sake of clarity, only four scenarios are assumed. The paper concludes that the declared synergy savings did not compensate for the increase in dead weight loss and the transfer of surplus from consumers to producers caused by increased market power. - Highlights: • A takeover blocked by the President of the Office of Competition and Consumer Protection was analysed. • A game theory-based model of the Polish wholesale electricity market was applied. • The impact of the takeover on electricity prices and generation levels, surplus transfers and dead weight loss was estimated. • The results were compared with the declared synergy savings

  3. Coal Data: A reference

    International Nuclear Information System (INIS)

    1991-01-01

    The purpose of Coal Data: A Reference is to provide basic information on the mining and use of coal, an important source of energy in the United States. The report is written for a general audience. The goal is to cover basic material and strike a reasonable compromise between overly generalized statements and detailed analyses. The section ''Coal Terminology and Related Information'' provides additional information about terms mentioned in the text and introduces new terms. Topics covered are US coal deposits, resources and reserves, mining, production, employment and productivity, health and safety, preparation, transportation, supply and stocks, use, coal, the environment, and more. (VC)

  4. Energy-saving belt conveyors installed in Polish collieries

    Directory of Open Access Journals (Sweden)

    Jerzy ANTONIAK

    2010-01-01

    Full Text Available An important problem of reducing energy consumption and dioxide emissions in the stage of construction and operation of mine belt conveyors is connected with their broad use in the industry. However, this notion is related to a reduction of electric energy consumption for conveyor drive and for production of conveyor components and assemblies (belts, rollers, load-bearing structure etc.. An essential role is played by an increased life of belt conveyors assemblies and components, principally belts. A reduced electric energy consumption results in a decreased CO2 emissions, e.g. hard coal – fired power station issues 0.28 kg CO2 per production of 1 kWh, in to answer production of 1 t steel accounts for 3.2 t CO2 emissions. The subject-matter presented in the paper concerning energy-saving in the horizontally and inclined mine belt conveyors installed in a Polish colliery – Anna, Jankowice and Marcel, has a big economic significance and it is important from the point of view of environmental protection.

  5. X-ray structural analysis of some Indian coals

    International Nuclear Information System (INIS)

    Binoy K Saikia, B.K.

    2009-01-01

    Coal is one of the most abundant energy resources and has the capability to meet future energy needs with high reliability. The use of coal as an energy source and as a source of organic chemicals feedstock may become more important in the future. It is physically and chemically a heterogeneous and carbonaceous rock which consists of organic and inorganic materials. Assam coal has been, and continuous to be, a valuable energy source, especially for the various industry in India and for liquefactions of coal. The basic chemical structure of coal that has been widely accepted today was built up from the synthesis of results obtained from X-ray diffraction data. The present paper reports a comparative investigation of coals from different collieries/areas of Makum coal field, Assam viz. Ledo, Tikak, Baragolai, Tipong and Tirap collieries Makum coal field, Assam with the help of X-ray diffraction (XRD). The X-ray diffraction patterns indicate that the coals are amorphous in nature. The present XRD method includes the evaluation of Function of Radial Distribution of Atoms (FRDA) and structural interpretations of the coals from their Radial Distribution Function (RDF) plots after proper corrections for air scatter, absorption by sample and polarization. The curve intensity profiles in FRDA clearly show quite regular molecular packets for these coals. The first maxima in the FRDA curves was obtained at r= 0.4 Amstrong for Ledo, Baragolai and Tipong coals whereas for Tikak coal it was observed at r= 0.5 Amstrong. The first maximum in the pair distribution function plots, G (r) of Ledo, Tikak, and Tipong coals was obtained at r=0.15 nm whereas for Baragolai and Tirap coals it was observed at r=0.14 nm and r=0.12 nm respectively, which relates to the C=C (aliphatic/aromatic) bonds in coal matrix. The Assam coal samples from Ledo, Tikak, Baragolai, Tipong and Tirap collieries of Makum coalfield have almost the same RDF inter-atomic distances except slight differences. This

  6. Fusion - 2050 perspective (in Polish)

    CERN Document Server

    Romaniuk, R S

    2013-01-01

    The results of strongly exothermic reaction of thermonuclear fusion between nuclei of deuterium and tritium are: helium nuclei and neutrons, plus considerable kinetic energy of neutrons of over 14 MeV. DT nuclides synthesis reaction is probably not the most favorable one for energy production, but is the most advanced technologically. More efficient would be possibly aneutronic fusion. The EU by its EURATOM agenda prepared a Road Map for research and implementation of Fusion as a commercial method of thermonuclear energy generation in the time horizon of 2050.The milestones on this road are tokomak experiments JET, ITER and DEMO, and neutron experiment IFMIF. There is a hope, that by engagement of the national government, and all research and technical fusion communities, part of this Road Map may be realized in Poland. The infrastructure build for fusion experiments may be also used for material engineering research, chemistry, biomedical, associated with environment protection, power engineering, security, ...

  7. Indonesian coal export potential

    International Nuclear Information System (INIS)

    Millsteed, Ch.; Jolly, L.; Stuart, R.

    1993-01-01

    Indonesia's coal mining sector is expanding rapidly. Much of the increase in coal production since the mid-1980s has been exported. Indonesian coal mining companies have large expansion programs and continuing strong export growth is projected for the remainder of the 1990s. The low mining costs of indonesian coal, together with proximity to Asian markets, mean that Indonesia is well placed to compete strongly with other thermal coal exporters and win market share in the large and expanding thermal coal market in Asia. However, there is significant uncertainty about the likely future level of Indonesia's exportable surplus of coal. The government's planned expansion in coal fired power generation could constrain export growth, while the ability of producers to meet projected output levels is uncertain. The purpose in this article is to review coal supply and demand developments in Indonesia and, taking account of the key determining factors, to estimate the level of coal exports from Indonesia to the year 2000. This time frame has been chosen because all currently committed mine developments are expected to be on stream by 2000 and because it is difficult to project domestic demand for coal beyond that year. 29 refs., 8 tabs., 7 figs

  8. Microbiological flora and nail polish: a brief report.

    Science.gov (United States)

    Rayan, G M; Flournoy, D J; Schlageter, P

    1994-11-01

    Removing nail polish and prosthetic nails from operating room (OR) personnel prior to scrubbing and from patients prior to hand surgery is recommended but not practiced in many hospitals. There is concern that nail polish can act as a vehicle for the transfer of infectious agents. This study was designed to determine the incidence of microbiological flora of nail polish in a clinical setting.

  9. Monitoring of Robot Assisted Polishing through parameters of acoustic emission

    DEFF Research Database (Denmark)

    Lazarev, Ruslan; Top, Søren; Bilberg, Arne

    The polishing process is essential for the surface generation of machine tooling components in advanced manufacturing. While robot assisted polishing is faster and more consistent than manual polishing, it can still consume a significant part of ma- chining time and operator presence time...

  10. 21 CFR 872.6030 - Oral cavity abrasive polishing agent.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Oral cavity abrasive polishing agent. 872.6030... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6030 Oral cavity abrasive polishing agent. (a) Identification. An oral cavity abrasive polishing agent is a device in paste or powder form...

  11. Brown coal - on the way to industrial-scale upgrading

    International Nuclear Information System (INIS)

    Speich, P.

    1981-01-01

    The main fields of development of Rheinische Braunkohlenwerke AG (Rheinbraun) in the field of brown coal upgrading are reported, i.e. production of synthesis gas, SNG, and liquid products. The Rheinbraun research programme involves the processes of high-temperature-Winkler gasification, hydrogasification, hydroliquefaction, tube stills, and methanation plants. In the long run, nuclear power will be indispensable for base load power supply so that brown coal can be upgraded instead of being used directly for electric power generation. (HS) [de

  12. Effect of Coal Grain Size on Sorption Capacity with Respect to Propylene and Acetylene

    Directory of Open Access Journals (Sweden)

    Agnieszka Dudzińska

    2017-11-01

    Full Text Available Propylene and acetylene are released to mine air with the increase in the temperature of self-heating coal. Concentrations of these gases in mine air are applied as indicators of the progress of the self-heating process. Hydrocarbons emitted from the self-ignition center are sorbed on coal, while migrating through the mine workings. Coal crushed during the mining process is characterized by a high sorption capacity, which facilitates the sorption phenomena. This results in the decrease in hydrocarbons content in mine air, and in the subsequent incorrect assessment of the development of the self-heating process. The results of the experimental study on propylene and acetylene sorption on Polish coals acquired from operating coal mines are presented in this paper. Bituminous coal is characterized by a high sorption capacity with respect to unsaturated hydrocarbons, like propylene and acetylene. The sorbed volumes depend on the grade of metamorphism, porosity, and chemical characteristics of coal. Low level of metamorphism, increased porosity, and oxygen content result in higher sorption capacity of coals. The reduction in grain size of coals also results in the increased sorption capacity with respect to hydrocarbons. The most significant increase in the volumes of sorbed propylene and acetylene with the decrease in grain class was observed for coals of low porosity, high grade of metamorphism, and low to medium sorption capacities. The 10-fold decrease in coal grain size resulted in the 3 to 6-fold increase in the volume of sorbed propylene, and 2-fold increase for acetylene. The decrease in grain size results in higher accessibility of pore structure, increased pore volume and area, and higher number of active centers interacting with hydrocarbons of dipole characteristics. For coals with low grade metamorphism, high porosity, and high sorption capacity the volumes of sorbed propylene and acetylene increased only slightly with the decrease in

  13. Fundamental research on surface science of coal in support of physical beneficiation of coal: Quarterly technical progress report, January 1--March 31, 1989

    Energy Technology Data Exchange (ETDEWEB)

    Good, R. J.; Keller, Jr., D. V.

    1989-01-01

    Research on coal surfaces continued. Our contact angle study of the decane-water-coal system has been extended using various ranks of coal. The study of the effect of surface oxidation on contact angles has also been extended to Upper Freeport, Illinois No. 6 and Kentucky No. 9 coals. Measurements of contact angles of liquid-air interfaces, on polished surfaces of coal of two different ranks, have been made using the captive drop technique. The data have been analyses using the acid/base theory. Some preliminary contact angle measurements have been made on rock pyrite, using the microscopic technique. The measurements were carried out for decane-water interfaces. A study of laboratory-scale agglomeration has been undertaken, using an Osterizer blender. The coals used were Illinois No. 6 and Kentucky No. 9. The effect of CO/sub 2/ on the agglomeration process has been looked into. Finally, the adsorption alcohols (cyclohexanol and n-octanol) from both aqueous and non-aqueous solutions, onto coal, has been measured. Two ranks of coal were used: Upper Freeport (mvb) and Illinois No. 6 (hvcb). 9 refs., 6 figs., 17 tabs.

  14. Determination of the cleat angle distribution of the RECOPOL coal seams, using CT-scans and image analysis on drilling cuttings and coal blocks

    Energy Technology Data Exchange (ETDEWEB)

    Wolf, Karl-Heinz A.A.; Ephraim, Rudy [Delft University of Technology, Department of Geotechnology, Stevinweg 1, 2628 CN, Delft (Netherlands); van Bergen, Frank; Pagnier, Henk [TNO, Princetonlaan 6, 3584 CB, Utrecht (Netherlands)

    2008-02-01

    Cleat orientation, cleat frequency and cleat angle distribution of deep coal seams are only available by the use of drilling cores and from coal mine samples. Coal drilling cuttings are a cheap and fast alternative to measure cleat angle distributions with the use of image analysis techniques. In this study oriented coal samples and drilling cuttings of the RECOPOL field experiment are compared and used to explain and validate the proposed method. In other words, cleat angle distributions from drilling cuttings are measured by image analysis. The geological framework of the polish coals is described. The image analysis methodologies for the measurement of fracture faces of cuttings and from CT-scan images, derived from these coals, are explained. The results of the methods on the cuttings are compared with cleat orientation distributions from CT-scans and artificial fragments from coal blocks of the same seams. These evaluations show high agreements between the methods. The cleat angle distributions of drilling cuttings of four seams are compared with the cleat orientation distributions of a regional structural geological study. The high correlation in this study shows that cleat angle distributions of coal seams can be used as input parameters for reservoir modelling. (author)

  15. Testing the electrostatic characteristics of polypropylene fabric with metallic yarns, intended for use in coal mines threatened by the explosion hazard. Part 2: Tests in coal mine

    International Nuclear Information System (INIS)

    Talarek, M; Orzech, L

    2011-01-01

    The aim of this paper was to assess the electrostatic safety of polypropylene fabric with metallic yarns intended for use in coal mines. Such fabrics have not been used in the Polish mining industry yet. The tests conducted have been divided into two subgroups: laboratory tests and tests in a coal mine. This paper presents the results of tests in a coal mine, where we have focused on the resistance-to-ground in some specific situations. Bags made of fabric at the roadway face were tested, as well as the roll of fabric during transport and carried by a miner. The results obtained allow the reliable assessment of the risk of using fabrics with metallic yarns in the explosive atmosphere which often occurs in coal mines.

  16. Professional Training of Economists at Polish Universities

    Science.gov (United States)

    Ogienko, Olena

    2016-01-01

    Polish experience in professional training of economists at university has been generalized. Structural, content and procedural peculiarities of the training have been defined. It has been proved that key factors for reforming economic education in Poland are globalization, internationalization, integration, technologization and informatization.…

  17. Knowledge Mobilisation in the Polish Education System

    Science.gov (United States)

    Fazlagic, Jan; Erkol, Arif

    2015-01-01

    Poland has made substantial progress in improving the quality of its education system in recent years. This paper aims to describe the situation of the Polish education system from a knowledge management perspective and, to some extent, through innovation policies in education. The many challenges, this paper argues, can be tackled only through…

  18. Sexual Health of Polish Athletes with Disabilities

    Directory of Open Access Journals (Sweden)

    Ryszard Plinta

    2015-06-01

    Full Text Available The purpose of this study was to determine sexual functioning of Polish athletes with disabilities (including paralympians. The study encompassed 218 people with physical disabilities, aged between 18 and 45 (149 men and 69 women. The entire research population was divided into three groups: Polish paralympians (n = 45, athletes with disabilities (n = 126 and non-athletes with disabilities (n = 47. The quality of sexual life of Polish paralympians was measured by using the Polish version of Female Sexual Function Index and International Index of Erectile Function. Clinically significant erectile dysfunctions were most often diagnosed in non-athletes (83.33% with 50% result of severe erectile dysfunctions, followed by athletes and paralympians with comparable results of 56.98% and 54.17% respectively (p = 0.00388. Statistically significant clinical sexual dysfunctions concerned lubrication, orgasm as well as pain domains, and prevailed among female non-athletes (68.42%, 68.42% and 57.89%. Practising sports at the highest level has a favourable effect on the sexuality of men and women with physical disabilities. Men with physical disabilities manifest more sexual disorders than women, an aspect which should be considered by health-care professionals working with people with disabilities.

  19. Technological Advances of Robot Assisted Polishing

    DEFF Research Database (Denmark)

    Lazarev, Ruslan; Top, Søren; Grønbæk, Jens

    The efficient polishing of surfaces is very important in mould and die industry. Fine abrasive processes are widely used in industry for the first steps for the production of tools of high quality in terms of finishing accuracy, form and surface integrity. While manufacturing of most components r...

  20. Polish Complementary Schools in Iceland and England

    Science.gov (United States)

    Zielinska, Malgorzata; Kowzan, Piotr; Ragnarsdóttir, Hanna

    2014-01-01

    Since 2004, the opening of labour markets has spurred a considerable number of Poles to emigrate e.g. to Iceland and England. Families with school age children have had the challenge of adapting to foreign environments and school systems. Polish complementary schools have played an important, albeit ambivalent, role in this process. Through focus…

  1. Screening of metal-resistant coal mine bacteria for biofabrication of ...

    Indian Academy of Sciences (India)

    Abstract. Green synthesis approaches for nanoparticle synthesis are considered as nontoxic, eco-friendly and cost-effective approaches than other physical and chemical approaches. Here, we report green synthesis of silver nanoparticle using the bacteria from the habitat of relatively metal-rich coal mine dust. The bacteria ...

  2. Transformation of the Polish Banking Sector

    Directory of Open Access Journals (Sweden)

    Marek Stefański

    2009-07-01

    Full Text Available In the post-war period the banking system in Poland underwent two important system transitions: after 1946 and after 1989. The third transformation began after May 1, 2004, but it did not have a systemic character. The Polish banking sector started to operate on the Single European Market. The first part of the paper is devoted to the problems of the banks transformations after 1989 with a special focus on the quantitative development of banks in 19892008, and on subsequent privatisation and consolidation processes. The former intensified in 19891999, and the latter in 19992002. The consolidation process was very noticeable in the sector of cooperative banks after 1994. The second part of the paper includes an economic and financial analysis of the banks. A lot of attention was paid to the liquidity of the banking sector. It was assessed as good, which was confirmed by a short-term rating of Moodys and by the Financial Stability Report 2009, published by the National Bank of Poland in June 2009. The comparison of the net profit of the banking sector in 19972008 shows its dependence on the economic situation and policy. The number of banks with capital adequacy ratio well above the minimum required by the banking supervision is rising. The financial power ratings are not favorable for the domestic banks. The third part of the paper focuses on the development directions of the Polish banking sector. It may be concluded on the basis of the analysis that privatisation and consolidation processes will be continued. They will concentrate on the capital of foreign banks already operating in Poland. As compared with individual foreign banks, the potential of the Polish banking sector is week. The fourth part of the paper focuses on the presentation Polish banking sector in the context of European Union banking sector. The paper finishes with conclusions. Generally, Polish banks have to implement a strategy to enable them to compete on the Single

  3. Biological production of ethanol from coal

    Energy Technology Data Exchange (ETDEWEB)

    1992-12-01

    Due to the abundant supply of coal in the United States, significant research efforts have occurred over the past 15 years concerning the conversion of coal to liquid fuels. Researchers at the University of Arkansas have concentrated on a biological approach to coal liquefaction, starting with coal-derived synthesis gas as the raw material. Synthesis gas, a mixture of CO, H[sub 2], CO[sub 2], CH[sub 4] and sulfur gases, is first produced using traditional gasification techniques. The CO, CO[sub 2] and H[sub 2] are then converted to ethanol using a bacterial culture of Clostridium 1jungdahlii. Ethanol is the desired product if the resultant product stream is to be used as a liquid fuel. However, under normal operating conditions, the wild strain'' produces acetate in favor of ethanol in conjunction with growth in a 20:1 molar ratio. Research was performed to determine the conditions necessary to maximize not only the ratio of ethanol to acetate, but also to maximize the concentration of ethanol resulting in the product stream.

  4. Chemical mechanical glass polishing with cerium oxide: Effect of selected physico-chemical characteristics on polishing efficiency

    Czech Academy of Sciences Publication Activity Database

    Janoš, P.; Ederer, J.; Pilařová, V.; Henych, Jiří; Tolasz, Jakub; Milde, D.; Opletal, T.

    2016-01-01

    Roč. 362, SEP (2016), s. 114-120 ISSN 0043-1648 R&D Projects: GA MŠk(CZ) LM2015073 Institutional support: RVO:61388980 Keywords : Chemical mechanical polishing * Ceria-based polishing powders * Polishing efficienc Subject RIV: CA - Inorganic Chemistry Impact factor: 2.531, year: 2016

  5. Clean coal technologies

    International Nuclear Information System (INIS)

    Aslanyan, G.S.

    1993-01-01

    According to the World Energy Council (WEC), at the beginning of the next century three main energy sources - coal, nuclear power and oil will have equal share in the world's total energy supply. This forecast is also valid for the USSR which possesses more than 40% of the world's coal resources and continuously increases its coal production (more than 700 million tons of coal are processed annually in the USSR). The stringent environmental regulations, coupled with the tendency to increase the use of coal are the reasons for developing different concepts for clean coal utilization. In this paper, the potential efficiency and environmental performance of different clean coal production cycles are considered, including technologies for coal clean-up at the pre-combustion stage, advanced clean combustion methods and flue gas cleaning systems. Integrated systems, such as combined gas-steam cycle and the pressurized fluidized bed boiler combined cycle, are also discussed. The Soviet National R and D program is studying new methods for coal utilization with high environmental performance. In this context, some basic research activities in the field of clean coal technology in the USSR are considered. Development of an efficient vortex combustor, a pressurized fluidized bed gasifier, advanced gas cleaning methods based on E-beam irradiation and plasma discharge, as well as new catalytic system, are are presented. In addition, implementation of technological innovations for retrofitting and re powering of existing power plants is discussed. (author)

  6. Coal sector profile

    Energy Technology Data Exchange (ETDEWEB)

    1990-06-05

    Coal is our largest domestic energy resource with recoverable reserves estimated at 268 billion short tons or 5.896 quads Btu equivalent. This is approximately 95 percent of US fossil energy resources. It is relatively inexpensive to mine, and on a per Btu basis it is generally much less costly to produce than other energy sources. Its chief drawbacks are the environmental, health and safety concerns that must be addressed in its production and consumption. Historically, coal has played a major role in US energy markets. Coal fueled the railroads, heated the homes, powered the factories. and provided the raw materials for steel-making. In 1920, coal supplied over three times the amount of energy of oil, gas, and hydro combined. From 1920 until the mid 1970s, coal production remained fairly constant at 400 to 600 million short tons a year. Rapid increases in overall energy demands, which began during and after World War II were mostly met by oil and gas. By the mid 1940s, coal represented only half of total energy consumption in the US. In fact, post-war coal production, which had risen in support of the war effort and the postwar Marshall plan, decreased approximately 25 percent between 1945 and 1960. Coal demand in the post-war era up until the 1970s was characterized by increasing coal use by the electric utilities but decreasing coal use in many other markets (e.g., rail transportation). The oil price shocks of the 1970s, combined with natural gas shortages and problems with nuclear power, returned coal to a position of prominence. The greatly expanded use of coal was seen as a key building block in US energy strategies of the 1970s. Coal production increased from 613 million short tons per year in 1970 to 950 million short tons in 1988, up over 50 percent.

  7. Coal gasification and the power production market

    International Nuclear Information System (INIS)

    Howington, K.; Flandermeyer, G.

    1995-01-01

    The US electric power production market is experiencing significant changes sparking interest in the current and future alternatives for power production. Coal gasification technology is being marketed to satisfy the needs of the volatile power production industry. Coal gasification is a promising power production process in which solid coal is burned to produce a synthesis gas (syn gas). The syn gas may be used to fuel combustion integrated into a facility producing electric power. Advantages of this technology include efficient power production, low flue gas emissions, flexible fuel utilization, broad capability for facility integration, useful process byproducts, and decreased waste disposal. The primary disadvantages are relatively high capital costs and lack of proven long-term operating experience. Developers of coal gasification intend to improve on these disadvantages and lop a strong position in the power generation market. This paper is a marketing analysis of the partial oxidation coal gasification processes emerging in the US in response to the market factors of the power production industry. A brief history of these processes is presented, including the results of recent projects exploring the feasibility of integrated gasification combined cycle (IGCC) as a power production alternative. The current power generation market factors are discussed, and the status of current projects is presented including projected performance

  8. Importance of hard coal in electricity generation in Poland

    Science.gov (United States)

    Plewa, Franciszek; Strozik, Grzegorz

    2017-11-01

    Polish energy sector is facing a number of challenges, in particular as regards the reconstruction of production potential, diversification of energy sources, environmental issues, adequate fuels supplies and other. Mandatory implementation of Europe 2020 strategy in terms of “3x20” targets (20% reduction of greenhouse gases, 20% of energy from renewable sources, and 20% increase of efficiency in energy production) requires fast decision, which have to be coordinated with energetic safety issues, increasing demands for electric energy, and other factors. In Poland almost 80% of power is installed in coal fired power plants and energy from hard coals is relatively less expensive than from other sources, especially renewable. The most of renewable energy sources power plants are unable to generate power in amounts which can be competitive with coal fires power stations and are highly expensive, what leads o high prices of electric energy. Alternatively, new generation of coal fired coal power plants is able to significantly increase efficiency, reduce carbon dioxide emission, and generate less expensive electric power in amounts adequate to the demands of a country.

  9. Coal, culture and community

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-11-01

    16 papers are presented with the following titles: the miners; municipalisation and the millenium - Bolton-upon-Dearne Urban District Council 1899-1914; the traditional working class community revisited; the cultural capital of coal mining communities; activities, strike-breakers and coal communities; the limits of protest - media coverage of the Orgreave picket during the miners` strike; in defence of home and hearth? Families, friendships and feminism in mining communities; young people`s attitudes to the police in mining communities; the determinants of productivity growth in the British coal mining industry, 1976-1989; strategic responses to flexibility - a case study in coal; no coal turned in Yorkshire?; the North-South divide in the Central Coalfields; the psychological effects of redundancy and worklessness - a case study from the coalfields; the Dearne Valley initiative; the future under labour: and coal, culture and the community.

  10. Coal tar in dermatology

    Energy Technology Data Exchange (ETDEWEB)

    Roelofzen, J.H.J.; Aben, K.K.H.; Van Der Valk, P.G.M.; Van Houtum, J.L.M.; Van De Kerkhof, P.C.M.; Kiemeney, L.A.L.M. [Radboud University Nijmegen Medical Center, Nijmegen (Netherlands). Dept. of Dermatology

    2007-07-01

    Coal tar is one of the oldest treatments for psoriasis and eczema. It has anti-inflammatory, antibacterial, antipruritic and antimitotic effects. The short-term side effects are folliculitis, irritation and contact allergy. Coal tar contains carcinogens. The carcinogenicity of coal tar has been shown in animal studies and studies in occupational settings. There is no clear evidence of an increased risk of skin tumors or internal tumors. Until now, most studies have been fairly small and they did not investigate the risk of coal tar alone, but the risk of coal tar combined with other therapies. New, well-designed, epidemiological studies are necessary to assess the risk of skin tumors and other malignancies after dermatological use of coal tar.

  11. STUDY OF POLISHING AISI 316L WITH STRUCTURED ABRASIVE

    Directory of Open Access Journals (Sweden)

    François GOOSSENS

    2015-05-01

    Full Text Available Finishing process like polishing is usually used to obtain high quality mechanical surface characteristics such as texture and roughness. These operations are mainly handmade and need highly trained operators thus limiting their repeatability and profitability. To optimize the industrialization of the polishing process, it is therefore necessary to modelize the process to built efficient parameter database. The aim of this study is to characterise the polishing of 316L stainless steel with structured abrasive belts. The geometric data of the belts are given, and we then propose a model to determine material removal. An experimental test bench is set up to test this model and characterise the polishing process in terms of forces. It produces samples for different polishing conditions. The different polished surfaces are then analyzed thanks to the roughness and the wettability. Using experimental designs, we are able to validate the proposed model and identify the parameters that influence a polishing operation.

  12. Coal contract cost reduction through resale of coal

    International Nuclear Information System (INIS)

    Simon, R.

    1990-01-01

    The weak coal market of the 1980's has enabled utilities and other users of coal to enjoy stable or falling prices for coal supplies. Falling prices for coal stimulated the renegotiation of numerous coal contracts in recent years, as buyers look to take advantage of lower fuel prices available in the marketplace. This paper examines the use of coal resale transactions as a means of reducing fuel costs, and analyzes the benefits and risks associated with such transactions

  13. Coal and our environment

    International Nuclear Information System (INIS)

    1992-01-01

    This booklet describes how coal is important for economic development and how it can be used without environmental damage. Aspects covered include: improved air quality; Clean Air Act; controlling emissions from coal; flue gas desulfurization; acid rain; the greenhouse effect and climatic change; the cost of clean air; surface coal mining and land reclamation; underground mining and subsidence; and mining and water pollution including acid mine drainage

  14. Abstracts Book of 41. Scientific Assembly of Polish Chemical Society and Association of Engineers and Technicians of Chemical Industry

    International Nuclear Information System (INIS)

    1998-01-01

    Scientific Assembly of Polish Chemical Society and Association of Engineers and Technicians of Chemical Industry is the most important scientific forum of Polish Chemists. The state of the art in many basic, fundamental and applied investigations has been presented and discussed. The following scientific sessions and microsymposia have been proposed: theoretical chemistry; molecular interactions; metal compounds - chemical, physical, electronic and biological aspects; catalysis and surface physico-chemistry; polymers - radiochemistry, modifications, physics and analytical methods; organic and bioorganic chemistry; physico-chemistry of condensed matter; chemical metallurgy; environmental protection; inorganic technology; chemistry and technology of coal; radiation chemistry; analytical chemistry; chemical engineering; young scientists forum; chemical didactics; petrochemistry; energetic materials; membranes and membrane processes; medical chemistry

  15. Coal export facilitation

    International Nuclear Information System (INIS)

    Eeles, L.

    1998-01-01

    There is a wide range of trade barriers, particularly tariffs, in current and potential coal market. Commonwealth departments in Australia play a crucial role in supporting government industry policies. This article summarises some of more recent activities of the Department of Primary Industries and Energy (DPIE) in facilitating the export of Australian Coals. Coal export facilitation activities are designed to assist the Australian coal industry by directing Commonwealth Government resources towards issues which would be inappropriate or difficult for the industry to address itself

  16. Developing Queensland coal

    Energy Technology Data Exchange (ETDEWEB)

    Philp, A. [Australian QTherm (Australia)

    1998-11-01

    Despite regional economic woes and falling coal prices, there have been exciting developments in Queensland`s coal industry with the announcement of three new coal mines, four mine expansions and two mine feasibility studies being undertaken. The article describes new projects being undertaken in Coppabella, Morahbah North and Hall Creek all in the Northern Bowen Basin, and mine expansions underway at Burton, Enshan, Newlands and Oaky North. Feasibility studies are the progress in the Millmerran and Acland deposits in The Moreton Basin. However, a number of proposed expansions at some major mines, such as Moura, Saraji and Peak Downs, have been postponed due to falling international coal prices. 2 figs., 2 photos.

  17. Pyrolysis of Coal

    Directory of Open Access Journals (Sweden)

    Rađenović, A.

    2006-07-01

    Full Text Available The paper presents a review of relevant literature on coal pyrolysis.Pyrolysis, as a process technology, has received considerable attention from many researchers because it is an important intermediate stage in coal conversion.Reactions parameters as the temperature, pressure, coal particle size, heating rate, soak time, type of reactor, etc. determine the total carbon conversion and the transport of volatiles and therebythe product distribution. Part of the possible environmental pollutants could be removed by optimising the pyrolysis conditions. Therefore, this process will be subsequently interesting for coal utilization in the future

  18. Coal combustion technology in China

    International Nuclear Information System (INIS)

    Huang, Z.X.

    1994-01-01

    Coal is the most important energy source in China, the environmental pollution problem derived from coal burning is rather serious in China. The present author discusses coal burning technologies both in boilers and industrial furnaces and their relations with environmental protection problems in China. The technological situations of Circulating Fluidized Bed Coal Combustor, Pulverized Coal Combustor with Aerodynamic Flame Holder and Coal Water Slurry Combustion have been discussed here as some of the interesting problems in China only. (author). 3 refs

  19. SPECTRAL METHODS IN POLISH EMOTIONAL SPEECH RECOGNITION

    Directory of Open Access Journals (Sweden)

    Paweł Powroźnik

    2016-12-01

    Full Text Available In this article the issue of emotion recognition based on Polish emotional speech signal analysis was presented. The Polish database of emotional speech, prepared and shared by the Medical Electronics Division of the Lodz University of Technology, has been used for research. Speech signal has been processed by Artificial Neural Networks (ANN. The inputs for ANN were information obtained from signal spectrogram. Researches were conducted for three different spectrogram divisions. The ANN consists of four layers but the number of neurons in each layer depends of spectrogram division. Conducted researches focused on six emotional states: a neutral state, sadness, joy, anger, fear and boredom. The averange effectiveness of emotions recognition was about 80%.

  20. ACCOMPLISHMENTS OF THE AMERICAN-POLISH PROGRAM FOR ELIMINATION OF LOW EMISSIONS IN KRAKOW

    Energy Technology Data Exchange (ETDEWEB)

    BUTCHER,T.A.; PIERCE,B.

    1998-11-05

    In 1991, US and Polish officials signed a Memorandum of Understanding formally initiating and directing the Cracow Clean Fossil Fuels and Energy Efficiency Program. Developing a program approach for the most effective use of the available funds required considerable effort on the part of all project participants. The team recognized early that the cost of solving the low emissions problem even in only one city far exceeded the amount of available US funds. Economic conditions in Poland limited availability of local capital funds for environmental projects. Imposing environmental costs on struggling companies or city residents under difficult conditions of the early 1990's required careful consideration of the economic and political impacts. For all of these reasons the program sought to identify technologies for achieving air quality goals which, through improved efficiency and/or reduced fuel cost, could be so attractive economically as to lead to self-sustaining activities beyond the end of the formal project. The effort under this program has been focused into 5 main areas of interest as follows: (1) Energy Conservation and Extension of Central Station District Heating; (2) Replacement of Coal- and Coke-Fired Boilers with Natural Gas-Fired Boilers; (3) Replacement of Coal-Fired Home Stoves with Electric Heating Appliances; (4) Reduction of Emissions from Stoker-Fired Boiler Houses; and (5) Reduction of Emissions from Coal-Fired Home Heating Stoves.

  1. Polish 2012 growth references for preschool children.

    Science.gov (United States)

    Kułaga, Zbigniew; Grajda, Aneta; Gurzkowska, Beata; Góźdź, Magdalena; Wojtyło, Małgorzata; Swiąder, Anna; Różdżyńska-Świątkowska, Agnieszka; Litwin, Mieczysław

    2013-06-01

    Growth references are useful in monitoring a child's growth, which is an essential part of child care. The aim of this paper is to provide updated growth references for Polish preschool children and to assess how well children in Poland match or diverge from the World Health Organization (WHO) growth standards/references and recent German height-for-age references. The height-, weight-, body mass index-for-age, and weight-for-height references were constructed with the LMS method using data from a recent, large, population-representative sample of 4,941 preschool children aged 3 to 6 years (the OLA study). In the case of boys, the third, 50th, and 97th height percentiles of new Polish and German references overlap almost completely, whereas the WHO growth standards/references percentiles are systematically lower. In the case of girls, comparison between the new Polish and German height references showed conformity on the third and 50th percentile, whereas body height values of the WHO standards/references are shorter. Polish children aged 3 to 6 years from for the nation representative sample, had significantly greater than zero mean z scores of height-, weight-, and BMI-for-age and weight-for-height, relative to the WHO growth standards/references. The number of children in the sample with height-for-age below -2 SD was significantly lower than expected and number of children with height-for-age above +2 SD was significantly higher than expected. The OLA study growth references can be recommended as national references for preschool children in Poland.

  2. Polish normalization of the Body Esteem Scale

    Directory of Open Access Journals (Sweden)

    Małgorzata Lipowska

    2014-02-01

    Full Text Available Background Physical attractiveness plays an important part in one’s social functioning. The interest in one’s own appearance have been documented as widespread among the female population, but over the recent years it is more and more often emphasized that concentrating on body appearance concerns men as well. Franzoi and Shields (1984 created the Body Esteem Scale which allows to qualify the subject’s attitude towards his or her own body. The aim of the study was to create a Polish version of the Body Esteem Scale along with the norms for age and sex clusters. Participants and procedure The normalization sample consisted of 4298 participants: 1865 women aged 16 to 80 (M = 29.92; SD = 12.85 and 2433 men aged 16 to 78 (M = 28.74; SD = 11.50. Education levels among the participants were also controlled for. In order to create a Polish version of the Body Esteem Scale, translation was adopted as the adaptation strategy. Like the original one, the Polish scale comprises 35 items grouped into three gender specific subscales. The subscales for women include Sexual Attractiveness, Weight Concern, and Physical Condition, whereas the body esteem of is examined with regards to Physical Attractiveness, Upper Body Strength, and Physical Condition. Results Reliability of subscales was high both for females (Cronbach’s alpha from 0.80 to 0.89 and males (Cronbach’s alpha from 0.85 to 0.88. The given coefficients of reliability cover the original division into subscales adopted by the authors of BES. Conclusions We confirmed high reliability of the Polish version of the Body Esteem Scale, thus we recommend it as a diagnostic tool. Created norms allowed to refer results obtained in the course of research carried out on people with various disorders (e.g. eating disorders or body dysmorphic disorder with population data for corresponding age brackets.

  3. Polish Martial Law: The Crisis of Communism

    Science.gov (United States)

    2009-12-01

    Roman Catholic Church continued to exist, and a comparatively liberal cultural policy was in place, which continued a legitimate practice of most of...intervention. Their answers verify that for most Poles the fear 29 of losing sovereignty and Polish culture to Russian aggression overshadows all else, even...they going in? They did not,” Woodrow Wilson International Center for Scholars, http://www.wilsoncenter.org/news/ docs/ Historia -Jachranka%20-%20Stan

  4. The Indonesian coal industry

    International Nuclear Information System (INIS)

    Cook, A.; Daulay, B.

    2000-01-01

    In this comprehensive article the authors describe the origins and progress of the Indonesian coal industry and the role it plays, and will play, in the domestic energy scene and world coal trade. In the '80s, the Indonesian coal industry laid the basis for major expansion such that coal production rose from under a million tonnes in 1983 to 10.6 million tonnes in 1990, 50.9 million tonnes by 1996 and 61.2 million tonnes in 1992. At the same time, exports have increased from 0.4 million tonnes to 44.8 million tonnes. Current export levels are higher than originally expected, due in part to a slow down in the construction of electric power stations and a partial switch to natural gas. This has slowed the rate at which domestic coal demand has built up. The majority of coals currently exported are low rank steam coals, but some of the higher rank and very low ash coals are used for blast furnace injection, and a very small proportion may even be used within coking blends, even though they have poor coking properties. The Indonesian coal industry has developed very rapidly over the last six years to become a significant exporter, especially within the ASEAN context. The resources base appears to be large enough to support further increases in production above those already planned. It is probable that resources and reserves can be increased above the current levels. It is likely that some reserves of high value coals can be found, but it is also probable that the majority of additions to reserves will be lower in rank (and therefore quality) compared with the average of coals currently being mined. Reserves of qualities suitable for export will support that industry for a considerable period of time. However, in the longer term, the emphasis of production will increasingly swing to the domestic market

  5. Coals of Hungary

    Energy Technology Data Exchange (ETDEWEB)

    Landis, E.R.; Rohrbacher, T.J.; Gluskoter, H.; Fodor, B.; Gombar, G.; Sebestyen, I.

    1999-07-01

    As part of the activities conducted under the U.S. Hungarian Science and Technology Fund, a total of 39 samples from five coal mines in Hungary were selected for standard coal analyses and major, minor and trace elements analysis. The mine areas sampled were selected to provide a spectrum of coal quality information for comparison with other coal areas in central Europe and worldwide. All of the areas are of major importance in the energy budget of Hungary. The five sample sites contain coal in rocks of Jurassic, Cretaceous, Eocene, Miocene, and Pliocene age. The coals, from four underground and one surface mine, range in rank from high volatile bituminous to lignite B. Most of the coal produced from the mines sampled is used to generate electricity. Some of the power plants that utilize the coals also provide heat for domestic and process usage. The standard coal analysis program is based on tests performed in accordance with standards of the American Society for Testing and Materials (ASTM). Proximate and ultimate analyses were supplemented by determinations of the heating value, equilibrium moisture, forms of sulfur, free-swelling index, ash fusion temperatures (both reducing and oxidizing), apparent specific gravity and Hardgrove Grindability index. The major, minor and trace element analyses were performed in accordance with standardized procedures of the U.S. Geological Survey. The analytical results will be available in the International Coal Quality Data Base of the USGS. The results of the program provide data for comparison with test data from Europe and information of value to potential investors or cooperators in the coal industry of Hungary and Central Europe.

  6. Clean coal technologies and future prospects for coal

    International Nuclear Information System (INIS)

    Rose, A.; Torries, T.; Labys, W.

    1991-01-01

    The purpose of this paper is to analyze the future potential of coal in the US economy during the next 25 years in light of clean coal technologies. According to official US Department of Energy (DOE) designations, these technologies pertain only to the beneficiation, transformation, combustion, and postcombustion clean-up stages of the coal cycle; no coal mining or coal transport technologies are included. In general, clean coal technologies offer the prospect of mitigating environmental side-effects of coal utilization, primarily through improved operating efficiencies and lowered costs of air emission controls. If they prove successful, coal users will be able to meet more stringent environmental regulations at little or no additional cost. In assessing the influence of clean coal technologies on coal demand, we focus on the economics of three crucial areas: their development, their deployment, and coal utilization implications of their operation

  7. THE ECONOMICAL PRODUCTION OF ALCOHOL FUELS FROM COAL-DERIVED SYNTHESIS GAS. Includes quarterly technical progress report No.25 from 10/01/1997-12/31/1997, and quarterly technical progress report No.26 from 01/01/1998-03/31/1998; FINAL

    International Nuclear Information System (INIS)

    1999-01-01

    This project was divided into two parts. One part evaluated possible catalysts for producing higher-alcohols (C(sub 2) to C(sub 5+)) as fuel additives. The other part provided guidance by looking both at the economics of mixed-alcohol production from coal-derived syngas and the effect of higher alcohol addition on gasoline octane and engine performance. The catalysts studied for higher-alcohol synthesis were molybdenum sulfides promoted with potassium. The best catalysts produced alcohols at a rate of 200 g/kg of catalyst/h. Higher-alcohol selectivity was over 40%. The hydrocarbon by-product was less than 20%. These catalysts met established success criteria. The economics for mixed alcohols produced from coal were poor compared to mixed alcohols produced from natural gas. Syngas from natural gas was always less expensive than syngas from coal. Engine tests showed that mixed alcohols added to gasoline significantly improved fuel quality. Mixed-alcohols as produced by our catalysts enhanced gasoline octane and decreased engine emissions. Mixed-alcohol addition gave better results than adding individual alcohols as had been done in the 1980's when some refiners added methanol or ethanol to gasoline

  8. THE ECONOMICAL PRODUCTION OF ALCOHOL FUELS FROM COAL-DERIVED SYNTHESIS GAS. Includes quarterly technical progress report No.25 from 10/01/1997-12/31/1997, and quarterly technical progress report No.26 from 01/01/1998-03/31/1998

    Energy Technology Data Exchange (ETDEWEB)

    None

    1999-03-01

    This project was divided into two parts. One part evaluated possible catalysts for producing higher-alcohols (C{sub 2} to C{sub 5+}) as fuel additives. The other part provided guidance by looking both at the economics of mixed-alcohol production from coal-derived syngas and the effect of higher alcohol addition on gasoline octane and engine performance. The catalysts studied for higher-alcohol synthesis were molybdenum sulfides promoted with potassium. The best catalysts produced alcohols at a rate of 200 g/kg of catalyst/h. Higher-alcohol selectivity was over 40%. The hydrocarbon by-product was less than 20%. These catalysts met established success criteria. The economics for mixed alcohols produced from coal were poor compared to mixed alcohols produced from natural gas. Syngas from natural gas was always less expensive than syngas from coal. Engine tests showed that mixed alcohols added to gasoline significantly improved fuel quality. Mixed-alcohols as produced by our catalysts enhanced gasoline octane and decreased engine emissions. Mixed-alcohol addition gave better results than adding individual alcohols as had been done in the 1980's when some refiners added methanol or ethanol to gasoline.

  9. Characterization and Streptococcus mutans adhesion on air polishing dentin.

    Science.gov (United States)

    Tada, Kazuhiro; Oda, Hirotake; Inatomi, Michitomo; Sato, Soh

    2014-07-01

    Air polishing is known as an effective and time saving tooth cleaning method. However, this method increased surface roughness and bacterial adhesion on dentin surface. The aim of this study was to characterize and examine Streptococcus mutans adhesion on dentin surface after air polishing as compared to the conventional method. The dentin blocks (4 × 4 × 1 mm) were polished by a rubber cup with polishing material (Polishing) and air-polished by 25 μm glycine (G25), 65 μm glycine (G65), and 65 μm sodium bicarbonate (NHC65) microparticles. Surface roughness (Ra) was measured by a laser electron microscope. The amount of adhered S. mutans was quantified using a resazurin reduction assay (alamarBlue(®)). The Ra of G25 and G65 was significantly (p < 0.01) smaller than that of NHC65 and greater than that of Polishing. However, there was no significant difference in S. mutans adhesion among Polishing, G25, and G65, while NHC65 showed significantly (p < 0.01) higher S. mutans adhesion. Within the limitations of this in vitro study, air polishing using glycine microparticles conditioned S. mutans adhesion on dentin surface in a similar fashion than the conventional method, and less than air polishing using sodium bicarbonate microparticles.

  10. Effects of polishing procedures on color stability of composite resins.

    Science.gov (United States)

    Güler, Ahmet Umut; Güler, Eda; Yücel, Ali Cağin; Ertaş, Ertan

    2009-01-01

    The purpose of this study was to investigate the effect of different polishing methods on color stability of posterior, universal and nanohybrid composite resin restorative materials upon exposure to a staining agent. Twenty-five specimens were prepared for each of 5 different composite resins (Filtek Z250, Filtek P60, Quadrant LC, Grandio and Filtek Supreme). Specimens were divided into 5 groups and different polishing procedures, including polishing discs (Pd), polishing discs then diamond polishing paste (PdP), polishing discs then a liquid polishing system (Biscover) (PdB), and combinations of these (PdPB) were used. Unpolished specimens served as the control (C). The specimens were stored for 48 h in a coffee solution. The color of all specimens was measured before and after exposure with a colorimeter, and total color change (DeltaE*) were calculated. The data were analyzed with a two-way ANOVA and the means were compared by Tukey HSD test (alpha=0.05). The lowest color difference was observed in the groups PdP and C, while the highest color difference was observed in PdPB, and PdB. When comparing the five different restorative materials, no significant difference was observed between FiltekP60 and FiltekZ250, and these materials demonstrated significantly less color change than Quadrant LC and the nanohybrid materials (Grandio, Filtek Supreme). The posterior (Filtek P60) and universal (Filtek Z250) composite resin restorative materials, which do not contain tetraethyleneglycol dimethacrylate (TEGDMA), were found to be less stainable than the nanohybrid (Grandio, Filtek Supreme) and universal (Quadrant LC) composite resins, which contain TEGDMA. The use of diamond polishing paste after polishing with polishing discs significantly decreased staining when compared to the groups that used polishing discs alone, for all restorative materials tested. The highest color change values were obtained for the specimens that were polished with the Biscover liquid polish

  11. Effects of polishing procedures on color stability of composite resins

    Directory of Open Access Journals (Sweden)

    Ahmet Umut Güler

    2009-04-01

    Full Text Available The purpose of this study was to investigate the effect of different polishing methods on color stability of posterior, universal and nanohybrid composite resin restorative materials upon exposure to a staining agent. Twenty-five specimens were prepared for each of 5 different composite resins (Filtek Z250, Filtek P60, Quadrant LC, Grandio and Filtek Supreme. Specimens were divided into 5 groups and different polishing procedures, including polishing discs (Pd, polishing discs then diamond polishing paste (PdP, polishing discs then a liquid polishing system (Biscover (PdB, and combinations of these (PdPB were used. Unpolished specimens served as the control (C. The specimens were stored for 48 h in a coffee solution. The color of all specimens was measured before and after exposure with a colorimeter, and total color change (DE* were calculated. The data were analyzed with a two-way ANOVA and the means were compared by Tukey HSD test (a=0.05. The lowest color difference was observed in the groups PdP and C, while the highest color difference was observed in PdPB, and PdB. When comparing the five different restorative materials, no significant difference was observed between FiltekP60 and FiltekZ250, and these materials demonstrated significantly less color change than Quadrant LC and the nanohybrid materials (Grandio, Filtek Supreme. The posterior (Filtek P60 and universal (Filtek Z250 composite resin restorative materials, which do not contain tetraethyleneglycol dimethacrylate (TEGDMA, were found to be less stainable than the nanohybrid (Grandio, Filtek Supreme and universal (Quadrant LC composite resins, which contain TEGDMA. The use of diamond polishing paste after polishing with polishing discs significantly decreased staining when compared to the groups that used polishing discs alone, for all restorative materials tested. The highest color change values were obtained for the specimens that were polished with the Biscover liquid polish

  12. India clamours for coal

    Energy Technology Data Exchange (ETDEWEB)

    Nadkarni, S.

    2000-10-01

    The steadily deteriorating quality of coal provided by government-owned companies in India has persuaded coal users to follow the lead of the World Bank and call for deregulation of the sector to allow quality coal to be procured at competitive prices from the global market.Some 24 opencast mines belonging to Coal India Limited subsidiaries were to be expanded to produce 112 mta of coal but the World Bank terminated a loan of 507 million dollars from the total sanctioned loan of 1.06 bn. CIL refuses to accept that the loan was terminated because the government failed to meet the terms and conditions imposed at the time of the loan sanction. In addition to slow demand from the power sector, the state-owned coal companies have found the World Bank terms impossible to meet. The favourable debt market in India has come to their aid but even this will not enable the quality of coal to be improved for use in many power plants. The Maharashtra State Electricity Board has called for the formation of a joint venture with the private sector to explore for and supply quality coal. 1 photo.

  13. Imported coal remains flexible

    Energy Technology Data Exchange (ETDEWEB)

    Bernstein, F.

    1982-01-01

    The new law on coal tariff quotas is one year old. During this period hard coal imports increased by 1 million tons, in spite of the slowed down economic activities and the wait-and-see attitude of consumers. The author gives a first survey.

  14. Development of coal resources

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-09-01

    It is an important issue to expand stable coal supply areas for Japan, especially to assure stable supply of overseas coals. The investigations on geological structures in foreign countries perform surveys on geological structures in overseas coal producing countries and basic feasibility studies. The investigations select areas with greater business risks in coal producing countries and among private business entities. The geological structure investigations were carried out on China, Indonesia and Malaysia and the basic feasibility studies on Indonesia during fiscal 1994. The basic coal resource development investigations refer to the results of previous physical explorations and drilling tests to develop practical exploration technologies for coal resources in foreign countries. The development feasibility studies on overseas coals conduct technological consultation, surface surveys, physical explorations, and trial drilling operations, and provide fund assistance to activities related thereto. Fiscal 1994 has provided fund assistance to two projects in Indonesia and America. Fund loans are provided on investigations for development and import of overseas coals and other related activities. Liability guarantee for development fund is also described.

  15. Mechanochemical hydrogenation of coal

    Science.gov (United States)

    Yang, Ralph T.; Smol, Robert; Farber, Gerald; Naphtali, Leonard M.

    1981-01-01

    Hydrogenation of coal is improved through the use of a mechanical force to reduce the size of the particulate coal simultaneously with the introduction of gaseous hydrogen, or other hydrogen donor composition. Such hydrogen in the presence of elemental tin during this one-step size reduction-hydrogenation further improves the yield of the liquid hydrocarbon product.

  16. COAL USE REPORT

    Science.gov (United States)

    The world's coal reserves have been estimated to be about one exagram accessible with current extraction technology. The energy content has been valued at 290 zettajourles. Using a value of 15 terawatt as the current global energy consumption, the coal supply could global needs f...

  17. Abstracts Book of Jubilee Scientific Assembly of Polish Chemical Society and Association of Engineers and Technicians of Chemical Industry

    International Nuclear Information System (INIS)

    2000-01-01

    Scientific Assemblies of Polish Chemical Society and Association of Engineers and Technicians of Chemical Industry are most important chemical discussion forum organised annually in Poland. Basic as well as application studies in all chemical branches have been extensively presented. The next subjects was proposed as sections and symposia topics: organic chemistry, physical chemistry (chemical kinetics, catalysis, thermodynamics), membranes and membrane processes, biological chemistry, biotechnology, metalorganic compounds and complexes, polymer chemistry, crystallochemical study, spectroscopy in nowadays chemistry, supramolecular chemistry, chemistry and technology of coal, high-energetic materials, environment protection, didactics in chemistry, radiation chemistry, photochemistry, electrochemistry, chemistry and technology of carbohydrates, theoretical and computer chemistry, young scientists forum, history of chemistry

  18. Advanced space optics development in freeform optics design, ceramic polishing, rapid and extreme freeform polishing

    Science.gov (United States)

    Geyl, R.; Leplan, H.; Ruch, E.

    2017-09-01

    In this paper Safran-Reosc wants to share with the space community its recent work performed in the domain of space optics. Our main topic is a study about the advantages that freeform optical surfaces can offer to advanced space optics in term of compactness or performances. We have separated smart and extreme freeform in our design exploration work. Our second topic is to answer about the immediate question following: can we manufacture and test these freeform optics? We will therefore present our freeform optics capability, report recent achievement in extreme aspheric optics polishing and introduce to the industrialisation process of large off axis optics polishing for the ESO Extremely Large Telescope primary mirror segments. Thirdly we present our R-SiC polishing layer technology for SiC material. This technique has been developed to reduce costs, risks and schedule in the manufacturing of advanced SiC optics for Vis and IR applications.

  19. Industrial coal utilization

    Energy Technology Data Exchange (ETDEWEB)

    None

    1979-01-01

    The effects of the National Energy Act on the use of coal in US industrial and utility power plants are considered. Innovative methods of using coal in an environmentally acceptable way are discussed: furnace types, fluidized-bed combustion, coal-oil-mixtures, coal firing in kilns and combustion of synthetic gas and liquid fuels. Fuel use in various industries is discussed with trends brought about by uncertain availability and price of natural gas and fuel oils: steel, chemical, cement, pulp and paper, glass and bricks. The symposium on Industrial Coal Utilization was sponsored by the US DOE, Pittsburgh Energy Technology Center, April 3 to 4, 1979. Twenty-one papers have been entered individually into the EDB. (LTN)

  20. Underground Coal Thermal Treatment

    Energy Technology Data Exchange (ETDEWEB)

    Smith, P. [Univ. of Utah, Salt Lake City, UT (United States); Deo, M. [Univ. of Utah, Salt Lake City, UT (United States); Eddings, E. [Univ. of Utah, Salt Lake City, UT (United States); Sarofim, A. [Univ. of Utah, Salt Lake City, UT (United States); Gueishen, K. [Univ. of Utah, Salt Lake City, UT (United States); Hradisky, M. [Univ. of Utah, Salt Lake City, UT (United States); Kelly, K. [Univ. of Utah, Salt Lake City, UT (United States); Mandalaparty, P. [Univ. of Utah, Salt Lake City, UT (United States); Zhang, H. [Univ. of Utah, Salt Lake City, UT (United States)

    2012-01-11

    The long-term objective of this work is to develop a transformational energy production technology by insitu thermal treatment of a coal seam for the production of substitute natural gas (SNG) while leaving much of the coal's carbon in the ground. This process converts coal to a high-efficiency, low-GHG emitting gas fuel. It holds the potential of providing environmentally acceptable access to previously unusable coal resources. This topical report discusses the development of experimental capabilities, the collection of available data, and the development of simulation tools to obtain process thermo-chemical and geo-thermal parameters in preparation for the eventual demonstration in a coal seam. It also includes experimental and modeling studies of CO2 sequestration.

  1. The renaissance of coal

    International Nuclear Information System (INIS)

    Schernikau, Lars

    2013-01-01

    There is hardly another energy resource where public opinion and reality lie as far apart as they do for coal. Many think of coal as an inefficient relic from the era of industrialisation. However, such views underestimate the significance of this energy resource both nationally and globally. In terms of global primary energy consumption coal ranks second behind crude oil, which plays a central role in the energy sector. Since global electricity use is due to rise further, coal, being the only energy resource that can meet a growing electricity demand over decades, stands at the beginning of a renaissance, and does so also in the minds of the political leadership. Coal is indispensable as a bridging technology until the electricity demand of the world population can be met primarily through renewable resources.

  2. Enzymatic desulfurization of coal

    Energy Technology Data Exchange (ETDEWEB)

    Boyer, Y.N.; Crooker, S.C.; Kitchell, J.P.; Nochur, S.V.

    1991-05-16

    The overall objective of this program was to investigate the feasibility of an enzymatic desulfurization process specifically intended for organic sulfur removal from coal. Toward that end, a series of specific objectives were defined: (1) establish the feasibility of (bio)oxidative pretreatment followed by biochemical sulfate cleavage for representative sulfur-containing model compounds and coals using commercially-available enzymes; (2) investigate the potential for the isolation and selective use of enzyme preparations from coal-utilizing microbial systems for desulfurization of sulfur-containing model compounds and coals; and (3) develop a conceptual design and economic analysis of a process for enzymatic removal of organic sulfur from coal. Within the scope of this program, it was proposed to carry out a portion of each of these efforts concurrently. (VC)

  3. Hydrodynamic modelling in the Polish Zone of the Baltic Sea - an overview of Polish achievements

    Directory of Open Access Journals (Sweden)

    Ewa Jasińska

    2003-03-01

    Full Text Available This paper gives a general overview of Polish experience and achievements with regard to hydrodynamic modelling in the Polish zone of the Baltic Sea. The first work started already at the end of the sixties when the first 1D and 2D hydrodynamic models were set up. With the development of numerical methods and increasing computational power a number of 1D, 2D and 3D models were set up and tested. Global, regional and local models cover the most important water bodies,i.e. the Pomeranian Bay - Szczecin Lagoon and Gulf of Gdansk - Vistula Lagoon systems.

  4. Westphalian xiphosurans (Chelicerata) from the Upper Silesia Coal Basin of Sosnowiec, Poland

    Energy Technology Data Exchange (ETDEWEB)

    Filipak, P.; Krawczynski, W. [University of Slaski, Sosnowiec (Poland). Faculty of Paleontology and Stratigraphy

    1996-12-01

    The xiphosurans Bellinurus lunatus (Martin, 1809) and Euproops rotundatus (Prestwich, 1840) are described from sideritic concretions hosted by the Orzesze Beds (Westphalian B) in the Polish region of the Upper Silesia Coal Basin. Associated flora and fauna include terrestrial plant remains and a single palaeodictyopteran insect nymph. As no marine influences are known in this area since the Namurian A, these xiphosurans were probably freshwater organisms.

  5. COMPARATIVE STUDY OF PEDAGOGICAL FORECASTING GENESIS IN RUSSIAN AND POLISH PEDAGOGICAL EDUCATION

    Directory of Open Access Journals (Sweden)

    Alla Fedorovna Matuszak (Prisyazhnaya

    2016-02-01

    Full Text Available The paper describes the genesis of pedagogical forecasting in Russia and Poland in the context of the development of general forecasting theory mainly with the emphasis on pedagogical education. The periods of forecasting theory development (implicit, explicit, institutional, global are presented. The content of each period viewing Russian and Polish education is described. In the implicit period the first attempts are made to predict educational issues. During the explicit period pedagogical forecasting obtains methodology of research. In the institutional period pedagogical forecasting from the sphere of state planning becomes the activity necessary for all the participants of teaching and learning. The global period envi-sages implementing pedagogical forecasting theory to fulfill the tasks of modern education, e.g. doing international projects. The tasks of pedagogical forecasting in the global world include further convergence of educational systems of various countries.The purpose is to determine and describe the henesis of pedagogical forecasting in Russia and Polish pedagogical education in the context of the development of general forecasting theory.Methodology. To identify the periods theoretical methods (historical and analytical me-thod, comparative analysis, theoretical and methodological analysis, synthesis, generalization are used.The results of the research include specifying the periods of pedagogical prognostication as well as the tasks of pedagogical forecasting in the global world in Russian and Polish Universities.Practical implications of the research are of interest to educators of all levels, especially the ones working in higher pedagogical education.

  6. The wear of polished and glazed zirconia against enamel.

    Science.gov (United States)

    Janyavula, Sridhar; Lawson, Nathaniel; Lawson, Nathaniel; Cakir, Deniz; Beck, Preston; Ramp, Lance C; Burgess, John O

    2013-01-01

    The wear of tooth structure opposing anatomically contoured zirconia crowns requires further investigation. The purpose of this in vitro study was to measure the roughness and wear of polished, glazed, and polished then reglazed zirconia against human enamel antagonists and compare the measurements to those of veneering porcelain and natural enamel. Zirconia specimens were divided into polished, glazed, and polished then reglazed groups (n=8). A veneering porcelain (Ceramco3) and enamel were used as controls. The surface roughness of all pretest specimens was measured. Wear testing was performed in the newly designed Alabama wear testing device. The mesiobuccal cusps of extracted molars were standardized and used as antagonists. Three-dimensional (3D) scans of the specimens and antagonists were obtained at baseline and after 200 000 and 400 000 cycles with a profilometer. The baseline scans were superimposed on the posttesting scans to determine volumetric wear. Data were analyzed with a 1-way ANOVA and Tukey Honestly Significant Difference (HSD) post hoc tests (α=.05) Surface roughness ranked in order of least rough to roughest was: polished zirconia, glazed zirconia, polished then reglazed zirconia, veneering porcelain, and enamel. For ceramic, there was no measureable loss on polished zirconia, moderate loss on the surface of enamel, and significant loss on glazed and polished then reglazed zirconia. The highest ceramic wear was exhibited by the veneering ceramic. For enamel antagonists, polished zirconia caused the least wear, and enamel caused moderate wear. Glazed and polished then reglazed zirconia showed significant opposing enamel wear, and veneering porcelain demonstrated the most. Within the limitations of the study, polished zirconia is wear-friendly to the opposing tooth. Glazed zirconia causes more material and antagonist wear than polished zirconia. The surface roughness of the zirconia aided in predicting the wear of the opposing dentition

  7. Tribological approach to study polishing of road surface under traffic

    OpenAIRE

    KANE, Malal; DO, Minh Tan

    2007-01-01

    The polishing phenomenon of road pavements under the vehicle traffic constitutes the main mechanism inherent to the loss of skid resistance over time. A better understanding of this phenomenon would allow an improvement of road safety. This study comprises a review of laboratory test and a model simulating the polishing of road surfaces. The laboratory test uses a polishing machine so called 'Wehner-Schulze' which can reproduce the evolution of the road texture from specimens taken directly f...

  8. Polish Phoneme Statistics Obtained On Large Set Of Written Texts

    Directory of Open Access Journals (Sweden)

    Bartosz Ziółko

    2009-01-01

    Full Text Available The phonetical statistics were collected from several Polish corpora. The paper is a summaryof the data which are phoneme n-grams and some phenomena in the statistics. Triphonestatistics apply context-dependent speech units which have an important role in speech recognitionsystems and were never calculated for a large set of Polish written texts. The standardphonetic alphabet for Polish, SAMPA, and methods of providing phonetic transcriptions are described.

  9. NMR imaging studies of coal

    Energy Technology Data Exchange (ETDEWEB)

    Ma, Z.R.; Zhang, P.Z.; Ding, G.L.; Li, L.Y.; Ye, C.H. [University of Science and Technology, Beijing (China). Dept. of Chemistry

    1996-06-01

    The permeation transportation and swelling behavior of solvents into coal are investigated by NMR imaging using pyridine-d{sub 5} and acetone-d{sub 6}. Images of coal swollen with deuterated solvents illuminate proton distributions of mobile phases within the coal macromolecular networks. More information about the chemical and physical structure of coal can be obtained using NMR imaging techniques.

  10. Preparing polished crystal slices with high precision orientation

    DEFF Research Database (Denmark)

    Mathiesen, S. Ipsen; Gerward, Leif; Pedersen, O.

    1974-01-01

    A polishing procedure is described which utilizes a high precision Laue technique for crystal orientation. Crystal slices with their final polished surfaces parallel to a crystallographic plane within 0.02° can be prepared. ©1974 The American Institute of Physics......A polishing procedure is described which utilizes a high precision Laue technique for crystal orientation. Crystal slices with their final polished surfaces parallel to a crystallographic plane within 0.02° can be prepared. ©1974 The American Institute of Physics...

  11. Visible Light Activated Photocatalytic Water Polishing System, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — This proposal targets development of a LED light activated photocatalytic water polishing system that enables reduction of organic impurities (TOC and...

  12. Assessing operability of a novel polisher arrangement using MMS

    International Nuclear Information System (INIS)

    Shor, S.W.W.

    1987-01-01

    A condensate polisher is intended to remove both particulate matter and ionic material from the condensate. Condensate polishers have normally been placed directly in the condensate system downstream of the condensate pumps. This inline location has certain disadvantages. These disadvantages are discussed. Placing the polisher in a sidestream location, where water is removed from the condensate system, pumped through the polisher, and then returned to the condensate system provides a solution to these disadvantages. Several possible types of sidestream installations is described. This has a polisher taking unpolished condensate from one compartment from one compartment of a divided hotwell in a specially modified condenser and returning polished condensate to the other compartment. The polisher is supplied by its own dedicated pumps, which have a head requirement sufficient only to overcome the pressure drop through the polisher circuit at a flow rate of 110% of maximum condensate flow. This concept is very attractive but has not yet been tested even though it is being installed in several new units. A simulation was, therefore, performed using MMS to provide confidence that this particular sidestream polisher arrangement was operationally viable

  13. Coal: Less than lackluster

    International Nuclear Information System (INIS)

    Doerell, P.

    1994-01-01

    Not many in the world coal industry will remember 1993 as a good year. The reasons for the poor state of affairs were first the weak economic climate, and second, the energy glut. For the first time after expanding steadily since the 70s, seaborne trade in hard coal fell by about 4% to 350M mt. Steam coal accounted for a good half of this volume. While demand continued to rise in the newly industrialized countries of the Pacific area, imports into Europe of both coking coal and steam coal fell sharply. The United States, CIS, and Canada had to accept substantial losses of export volume. Australia, as well as South Africa, Colombia, and Indonesia consolidated their market positions and Poland, too, recorded high volumes available for export. The positive news came from Australia, where in mid-December the New South Wales coal industry reported an increase in the net profit after tax from $A83M (about $55M) to $A98M (about $126M) in 1992/1993. This success was however ascribed less to an improvement in the fundamental mining indicators than to the fall in the Australian dollar and the lowering of corporate tax. The reduction in capital investment by 26% down to $A330M (after the previous year when it had also been cut by 25%) is seen by the chairman of the NSW Coal Assoc. as not auguring well for the industry's ability to meet the forecast growth in demand to the year 2000

  14. Coal Transition in the United Kingdom. An historical case study for the project 'Coal Transitions: Research and Dialogue on the Future of Coal'

    International Nuclear Information System (INIS)

    Fothergill, Steve

    2017-01-01

    This is one of the 6 country case-studies commissioned to collect experience on past coal transitions. The 6 countries are: Czech Republic, the Netherlands, Poland, Spain, UK, USA. Their role in the Coal Transitions project was to provide background information for a Synthesis Report for decision makers, and provide general lessons for national project teams to take into account in developing their coal transitions pathways for the future. The UK has virtually completed its move away from the production and use of coal - an astonishing transformation for an economy that once relied overwhelmingly on coal power. This is however a transformation that was never really 'planned' and the move away from coal started long before concerns about climate change achieved political prominence. Until as late as November 2015, for example, there was no government commitment to phase out coal in UK electricity generation. But it was already happening, and some of the most rapid change was actually in 2016, triggered in particular by the impact of a 'carbon tax' which has tipped the economics away from coal to gas-fired generation. A handful of coal-fired power stations will remain on the grid for a few years to help meet peak demand, but to all intents the UK is already entering the post-coal era. Whether this has been achieved without undue pain to coal mining areas is however deeply questionable. Job losses were for many years managed by a combination of redundancies and transfers to surviving mines. Redundancy payments, welfare benefits and early access to pensions provided support former miners, and careers advice and training was on offer. Most former miners have now reached retirement age. The big problem for mining communities has been replacement of the lost jobs. The UK has a long history of efforts to regenerate areas affected by coal closures and there is clear evidence that this has delivered positive results in the form of new jobs. Nevertheless

  15. (Pittsburgh Energy Technology Center): Quarterly technical progress report for the period ending June 30, 1987. [Advanced Coal Research and Technology Development Programs

    Energy Technology Data Exchange (ETDEWEB)

    None

    1988-02-01

    Research programs on coal and coal liquefaction are presented. Topics discussed are: coal science, combustion, kinetics, surface science; advanced technology projects in liquefaction; two stage liquefaction and direct liquefaction; catalysts of liquefaction; Fischer-Tropsch synthesis and thermodynamics; alternative fuels utilization; coal preparation; biodegradation; advanced combustion technology; flue gas cleanup; environmental coordination, and technology transfer. Individual projects are processed separately for the data base. (CBS)

  16. Coal fly ash as a resource for rare earth elements.

    Science.gov (United States)

    Franus, Wojciech; Wiatros-Motyka, Małgorzata M; Wdowin, Magdalena

    2015-06-01

    Rare earth elements (REE) have been recognised as critical raw materials, crucial for many clean technologies. As the gap between their global demand and supply increases, the search for their alternative resources becomes more and more important, especially for the countries which depend highly on their import. Coal fly ash (CFA), which when not utilised is considered waste, has been regarded as the possible source of many elements, including REE. Due to the increase in the energy demand, CFA production is expected to grow, making research into the use of this material a necessity. As Poland is the second biggest coal consumer in the European Union, the authors have studied different coal fly ashes from ten Polish power plants for their rare earth element content. All the fly ashes have a broadly similar distribution of rear earth elements, with light REE being dominant. Most of the samples have REE content relatively high and according to Seredin and Dai (Int J Coal Geol 94: 67-93, 2012) classification can be considered promising REE raw materials.

  17. Coal potential of Antartica

    Energy Technology Data Exchange (ETDEWEB)

    Rose, G.; McElroy, C.T.

    1987-01-01

    This report attempts to bring together available information on the coal deposits of Antarctica and discuss factors that would be involved if these deposits were to be explored and mined. Most of the reported principal coal deposits in Antarctica lie generally within the Transantarctic Mountains: the majority are of Permian age and are present in the Victoria Group of the Beacon Supergroup. Several other deposits have been recorded in East Antarctica and in the Antarctic Peninsula, including minor occurrences of Mesozoic and Tertiary coal and carbonaceous shale.

  18. Extreme coal handling

    Energy Technology Data Exchange (ETDEWEB)

    Bradbury, S; Homleid, D. [Air Control Science Inc. (United States)

    2004-04-01

    Within the journals 'Focus on O & M' is a short article describing modifications to coal handling systems at Eielson Air Force Base near Fairbanks, Alaska, which is supplied with power and heat from a subbituminous coal-fired central plant. Measures to reduce dust include addition of an enclosed recirculation chamber at each transfer point and new chute designs to reduce coal velocity, turbulence, and induced air. The modifications were developed by Air Control Science (ACS). 7 figs., 1 tab.

  19. Coal-fired generation

    CERN Document Server

    Breeze, Paul

    2015-01-01

    Coal-Fired Generation is a concise, up-to-date and readable guide providing an introduction to this traditional power generation technology. It includes detailed descriptions of coal fired generation systems, demystifies the coal fired technology functions in practice as well as exploring the economic and environmental risk factors. Engineers, managers, policymakers and those involved in planning and delivering energy resources will find this reference a valuable guide, to help establish a reliable power supply address social and economic objectives. Focuses on the evolution of the traditio

  20. Microbial desulfurization of coal

    International Nuclear Information System (INIS)

    Bos, P.; Boogerd, F.C.; Kuenen, J.G.

    1992-01-01

    In recent years, studies have been initiated to explore the possibilities of the use of biological systems in coal technology. This chapter discusses the principles behind the bioprocessing of coal, the advantages and disadvantages, and the economic feasibility of the process. For large-scale, coal-using, energy-producing plants, stack gas cleaning should be the treatment of choice. Biodesulfurization is preferable with industrial, small-scale, energy-producing plants. Treatment of the stack gases of these plants is not advisable because of high investment costs. Finally, it should be realized that biodesulfurization produces a waste stream that needs further treatment. 91 refs

  1. Plasma electrolytic polishing of metalized carbon fibers

    Directory of Open Access Journals (Sweden)

    Falko Böttger-Hiller

    2016-02-01

    Full Text Available Efficient lightweight structures require intelligent materials that meet versatile functions. Especially, carbon-fiber-reinforced polymers (CFRPs are gaining relevance. Their increasing use aims at reducing energy consumption in many applications. CFRPs are generally very light in weight, while at the same time being extremely stiff and strong (specific strength: CFRPs: 1.3 Nm kg–1, steel: 0.27 Nm kg–1; specific stiffness: CFRPs: 100 Nm kg–1, steel: 25 Nm kg–1. To increase performance and especially functionality of CFRPs, the integration of microelectronic components into CFRP parts is aspired. The functionalization by sensors, actuators and electronics can enable a high lightweight factor and a new level of failure-safety. The integration of microelectronic components for this purpose requires a working procedure to provide electrical contacts for a reliable connection to energy supply and data interfaces. To overcome this challenge, metalized carbon fibers are used. Metalized fibers are, similar to the usual reinforcing fibers, able to be soldered and therefore easy to incorporate into CFRPs. Unfortunately, metalized fibers have to be pre-treated by flux-agents. Until now, there is no flux which is suitable for mass production without destroying the polymer of the CFRP. The process of plasma electrolytic polishing (PeP could be an option, but is so far not available for copper. Thus, in this study, plasma electrolytic polishing is transferred to copper and its alloys. To achieve this, electrolytic parameters as well as the electrical setup are adapted. It can be observed that the gloss and roughness can be adjusted by means of this procedure. Finally, plasma electrolytic polishing is used to treat thin copper layers on carbon fibers.

  2. Competence of Irish and Polish Teachers in the Opinions of Young Polish Immigrants in Ireland

    Science.gov (United States)

    Augustyniak, Joanna

    2016-01-01

    Since 2004, Ireland has experienced the arrival of immigrants from various countries from all over the world including Poland. The Polish came to Ireland with their families including children of school age obliged to attend compulsory education. These children have attended schools dissimilar from the ones they are accustomed to in their home…

  3. Wind Directions in the Polish Tatras,

    Science.gov (United States)

    1982-01-26

    The study of anemometric conditions in the iatra Aoun- tains with the usually available observation data presents a rather difficult problem for two...year are presented in Table 2 and Fig. 1. Analysis of the anemometric conditions in the Polish Ta- tras and at 2odhale, on the basis of the observational...Vol. 29, 1947. 9. Milata, W. "The Foehn," Wierchy, Vol. 20, 1950. 10. Orlicz, M. " Anemometric Conditions on Peaks in the 2atras," Wiad. Sluzhby Hydro

  4. Polish students' opinion about medicinal cannabis

    OpenAIRE

    Mazur, Rafał; Masternak, Sebastian; Pająk, Michał; Parszewska, Katarzyna; Skórzyńska-Dziduszko, Katarzyna

    2017-01-01

    Mazur Rafał, Masternak Sebastian, Pająk Michał, Parszewska Katarzyna, Skórzyńska-Dziduszko Katarzyna. Polish students’ opinion about medicinal cannabis. Journal of Education, Health and Sport. 2017;7(9):233-242. eISSN 2391-8306. DOI http://dx.doi.org/10.5281/zenodo.894710 http://ojs.ukw.edu.pl/index.php/johs/article/view/4839 The journal has had 7 points in Ministry of Science and Higher Education parametric evaluation. Part B item 1223 (26....

  5. The reduction of atmospheric emissions after the implementation of first Polish nuclear power plant

    Science.gov (United States)

    Cholewiński, Maciej

    2018-04-01

    In this work the environmental benefits in the atmospheric emissions after the implementation of 3,000 MW nuclear power plants were assessed and presented. To determine the quantity of avoided emissions of CO2, NOx, SO2 and Hg compounds, harmonised stoichiometric combustion model dedicated to solid fuel fired power plant was created. To increase the credibility of the studies, future strict emission standards (Directive 2010/75/EU, BAT documents for LCP) were included as well. In conducted studies, representative samples of 3 different Polish solid fuels were examined (by comprehensive proximate and ultimate analysis) and used in assessment. It was proven that by the replacement of thermal solid fuel power plant by nuclear unit (with annual production rate of 22.4 TWh net) up to 16.4 million tonnes of lignite, 8.9 million tonnes of hard coal or 13.1 million tonnes of solid biomass can be saved. Further, for the case of lignite, the emission, at least, of 21.29 million tonnes of CO2 (6.9% of all Polish emission in 2015), 1,610 tonnes of dust (0.4%), 16,102 tonnes of NOx (2.2%), 16,102 tonnes of SO2 (2.0%) and 564 kg of mercury (5.9%) can be avoided. For selected hard coal, calculated emission savings were equal to 17.60 million tonnes of CO2 (5.7%), 1,357 tonnes of dust (0.4%), 13,566 tonnes of NOx (1.9%), 13,566 tonnes of SO2 (1.7%), 271 kg of mercury (2.9%), and for biomass - equal to 20.04 million tonnes of CO2 (6.5%), 1,471 tonnes of dust (0.4%), 14,712 tonnes of NOx (2.0%), 14,712 tonnes of SO2 (1.8%) and 294 kg of mercury (3.1%).

  6. The reduction of atmospheric emissions after the implementation of first Polish nuclear power plant

    Directory of Open Access Journals (Sweden)

    Cholewiński Maciej

    2018-01-01

    Full Text Available In this work the environmental benefits in the atmospheric emissions after the implementation of 3,000 MW nuclear power plants were assessed and presented. To determine the quantity of avoided emissions of CO2, NOx, SO2 and Hg compounds, harmonised stoichiometric combustion model dedicated to solid fuel fired power plant was created. To increase the credibility of the studies, future strict emission standards (Directive 2010/75/EU, BAT documents for LCP were included as well. In conducted studies, representative samples of 3 different Polish solid fuels were examined (by comprehensive proximate and ultimate analysis and used in assessment. It was proven that by the replacement of thermal solid fuel power plant by nuclear unit (with annual production rate of 22.4 TWh net up to 16.4 million tonnes of lignite, 8.9 million tonnes of hard coal or 13.1 million tonnes of solid biomass can be saved. Further, for the case of lignite, the emission, at least, of 21.29 million tonnes of CO2 (6.9% of all Polish emission in 2015, 1,610 tonnes of dust (0.4%, 16,102 tonnes of NOx (2.2%, 16,102 tonnes of SO2 (2.0% and 564 kg of mercury (5.9% can be avoided. For selected hard coal, calculated emission savings were equal to 17.60 million tonnes of CO2 (5.7%, 1,357 tonnes of dust (0.4%, 13,566 tonnes of NOx (1.9%, 13,566 tonnes of SO2 (1.7%, 271 kg of mercury (2.9%, and for biomass - equal to 20.04 million tonnes of CO2 (6.5%, 1,471 tonnes of dust (0.4%, 14,712 tonnes of NOx (2.0%, 14,712 tonnes of SO2 (1.8% and 294 kg of mercury (3.1%.

  7. Clean coal initiatives in Indiana

    Science.gov (United States)

    Bowen, B.H.; Irwin, M.W.; Sparrow, F.T.; Mastalerz, Maria; Yu, Z.; Kramer, R.A.

    2007-01-01

    Purpose - Indiana is listed among the top ten coal states in the USA and annually mines about 35 million short tons (million tons) of coal from the vast reserves of the US Midwest Illinois Coal Basin. The implementation and commercialization of clean coal technologies is important to the economy of the state and has a significant role in the state's energy plan for increasing the use of the state's natural resources. Coal is a substantial Indiana energy resource and also has stable and relatively low costs, compared with the increasing costs of other major fuels. This indigenous energy source enables the promotion of energy independence. The purpose of this paper is to outline the significance of clean coal projects for achieving this objective. Design/methodology/approach - The paper outlines the clean coal initiatives being taken in Indiana and the research carried out at the Indiana Center for Coal Technology Research. Findings - Clean coal power generation and coal for transportation fuels (coal-to-liquids - CTL) are two major topics being investigated in Indiana. Coking coal, data compilation of the bituminous coal qualities within the Indiana coal beds, reducing dependence on coal imports, and provision of an emissions free environment are important topics to state legislators. Originality/value - Lessons learnt from these projects will be of value to other states and countries.

  8. Integrated methanol synthesis

    International Nuclear Information System (INIS)

    Jaeger, W.

    1982-01-01

    This invention concerns a plant for methanol manufacture from gasified coal, particularly using nuclear power. In order to reduce the cost of the hydrogen circuits, the methanol synthesis is integrated in the coal gasification plant. The coal used is gasified with hydration by means of hydrogen and the crude gas emerging, after cooling and separating the carbon dioxide and hydrogen sulphide, is mixed with the synthetic gas leaving the methane cracking furnace. This mixture is taken to the methanol synthesis and more than 90% is converted into methanol in one pass. The gas mixture remaning after condensation and separation of methanol is decomposed into three fractions in low temperature gas decomposition with a high proportion of unconverted carbon monoxide. The flow of methane is taken to the cracking furnace with steam, the flow of hydrogen is taken to the hydrating coal gasifier, and the flow of carbon monoxide is taken to the methanol synthesis. The heat required for cracking the methane can either be provided by a nuclear reactor or by the coke left after hydrating gasification. (orig./RB) [de

  9. Clean utilization of coal

    International Nuclear Information System (INIS)

    Yueruem, Y.

    1992-01-01

    This volume contains 23 lectures presented at the Advanced Study Institute on 'Chemistry and Chemical Engineering of Catalytic Solid Fuel Conversion for the Production of Clean Synthetic Fuels', which was held at Akcay, Edremit, Turkey, between 21 July and August 3, 1991. Three main subjects: structure and reactivity of coal; cleaning of coal and its products, and factors affecting the environmental balance of energy usage and solutions for the future, were discussed in the Institute and these are presented under six groups in the book: Part 1. Structure and reactivity of coal; Part 2. Factors affecting environmental balance; Part 3. Pre-usage cleaning operations and processes; Part 4. Upgrading of coal liquids and gases; Part 5. Oxygen enriched processes; and Part 6. Probable future solution for energy and pollution problems. Separate abstracts have been prepared for all the lectures

  10. Quarterly coal report

    Energy Technology Data Exchange (ETDEWEB)

    Young, P.

    1996-05-01

    The Quarterly Coal Report (QCR) provides comprehensive information about U.S. coal production, distribution, exports, imports, receipts, prices, consumption, and stocks to a wide audience, including Congress, Federal and State agencies, the coal industry, and the general public. Coke production, consumption, distribution, imports, and exports data are also provided. The data presented in the QCR are collected and published by the Energy Information Administration (EIA) to fulfill data collection and dissemination responsibilities as specified in the Federal Energy Administration Act of 1974 (Public Law 93-275), as amended. This report presents detailed quarterly data for October through December 1995 and aggregated quarterly historical data for 1987 through the third quarter of 1995. Appendix A displays, from 1987 on, detailed quarterly historical coal imports data, as specified in Section 202 of the Energy Policy and Conservation Amendments Act of 1985 (Public Law 99-58). Appendix B gives selected quarterly tables converted to metric tons.

  11. Coal Mine Permit Boundaries

    Data.gov (United States)

    Earth Data Analysis Center, University of New Mexico — ESRI ArcView shapefile depicting New Mexico coal mines permitted under the Surface Mining Control and Reclamation Act of 1977 (SMCRA), by either the NM Mining these...

  12. Coal exports still growing

    International Nuclear Information System (INIS)

    Blain, M.

    1998-01-01

    It is shown that the swings and roundabouts of the Asian economic shake out and Australian dollar devaluation are starting to work their way through the Australian export coal market. Perhaps somewhat surprisingly, at this stage the results are not proving to be as bad as were at first predicted by some market watchers. Export revenue and tonnages are up 12% for the year to July 98. Coal exports totaling $9.5 billion left Australia's shores in the 12 months confirming coal as Australia's single largest export revenue earner. Sales volumes in the present financial year are still increasing, the market being driven by steadily increasing Asian demand for steaming coal from places like Korea, Malaysia, Thailand and the Philippines

  13. Coal; Le charbon

    Energy Technology Data Exchange (ETDEWEB)

    Viterbo, J.

    2011-09-15

    As the energy demand grows, coal is more and more exported and its trade is very flourishing. Asian countries produce 61% of the world production and Japan is the biggest coal importer: 27% of the world exports. The world reserves are huge: 860 billions tonnes which represents 130 years of today's production. The use of coal is very polluting and the quest of a clean coal is a challenge for the next decade. Different ways of improvement are currently developed: -) the use of more efficient filters to block polluting releases, -) the recovery of the energy of the smokes, -) a higher thermal yield through the use of supercritical cycles, or the addition of a gasification step to a combined cycle, or the simultaneous production of power, heat and chemical by-products, and -) the storage of CO{sub 2} produced in deep geological reservoirs. (A.C.)

  14. Uranium in coal

    International Nuclear Information System (INIS)

    Facer, J.F. Jr.

    1979-05-01

    United States production of coal in 1977 was 695 million short tons of which 477 million tons were burned in power plants. The ash from these power plants was about 67 million tons containing an estimated 900 tons U 3 O 8 , assuming 14 percent ash from the type of coal used by utilities and 12 ppM U contained in ash. Perhaps 1 to 3 percent of the domestic uranium requirement could be met from coal ash, provided processing technology could be developed for uranium recovery at acceptable costs. However, the environmental problems for disposal of the slimy leached ash would be enormous. The average uranium grade of coal in the United States is less than half of that of the Earth's crust. Burning the coal concentrates the contained uranium in the ash from 2 to 20 times. However, even at 20 times concentration, the percent uranium in coal ash is less than 1/100 of the grade of the uranium ore being processed today from conventional deposits. Although it is conceivable that some coal ash might contain enough uranium to make the ash an economic source of uranium, this is not now the case for ash from any major coal-fired power plant in the United States. During 1963 to 67, about 180,000 tons of uranium-bearing carbonaceous rock from the southwestern part of the Williston Basin were mined and processed to recover about 1 million pounds of U 3 O 8 . None of this material has been mined since 1967. The uranium reserves of the area are small, and the environmental problems with calcining the lignitic material may be prohibitive. Some other uraniferous coal and lignite could be mined and processed as a uranium ore, but less than half of one percent of the domestic $30 reserves are in coal. A few samples of mid-continent coal have been reported to contain about 100 ppM U but little is known about the size of such deposits or the likelihood that they will be mined and used for power plant fuel to produce a high-uranium ash

  15. Nanometre-sized pores in coal: Variations between coal basins and coal origin

    Science.gov (United States)

    Sakurovs, Richard; Koval, Lukas; Grigore, Mihaela; Sokolava, Anna; Ruppert, Leslie F.; Melnichenko, Yuri B.

    2018-01-01

    We have used small angle neutron scattering (SANS) to investigate the differences in methane and hexane penetration in pores in bituminous coal samples from the U.S., Canada, South Africa, and China, and maceral concentrates from Australian coals. This work is an extension of previous work that showed consistent differences between the extent of penetration by methane into 10–20 nm size pores in inertinite in bituminous coals from Australia, North America and Poland.In this study we have confirmed that there are differences in the response of inertinite to methane and hexane penetration in coals sourced from different coal basins. Inertinite in Permian Australian coals generally has relatively high numbers of pores in the 2.5–250 nm size range and the pores are highly penetrable by methane and hexane; coals sourced from Western Canada had similar penetrability to these Australian coals. However, the penetrability of methane and hexane into inertinite from the Australian Illawarra Coal Measures (also Permian) is substantially less than that of the other Australian coals; there are about 80% fewer 12 nm pores in Illawarra inertinite compared to the other Australian coals examined. The inertinite in coals sourced from South Africa and China had accessibility intermediate between the Illawarra coals and the other Australian coals.The extent of hexane penetration was 10–20% less than CD4 penetration into the same coal and this difference was most pronounced in the 5–50 nm pore size range. Hexane and methane penetrability into the coals showed similar trends with inertinite content.The observed variations in inertinite porosity between coals from different coal regions and coal basins may explain why previous studies differ in their observations of the relationships between gas sorption behavior, permeability, porosity, and maceral composition. These variations are not simply a demarcation between Northern and Southern Hemisphere coals.

  16. Coal utilization and environment

    International Nuclear Information System (INIS)

    Sanchez, J.C.D.; Formoso, M.L.L.

    1990-01-01

    This paper attempts at presenting a database on environmental pollution due to coal-fired power plants and coal-mining, according to regional and national bibliography available to the authors. Data on air, water and soil pollution in Rio Grande do Sul and Pollution due to mining in Santa Catarina are presented. The paper consists of a bibliographic compilation, with the quantification of polluting factors. (author)

  17. Coal pillar design procedures

    CSIR Research Space (South Africa)

    York, G

    2000-03-01

    Full Text Available ). ..................................................................................................................25 Figure 1-3 Stress in coal pillar versus pillar compression. After Wagner (1980).......................27 Figure 1-4 Frequency of pillar collapse versus the design safety factor. ..................................38 Figure 1-5 Frequency... ......................................................................................57 Table 2-6 Calculation of factor of safety of pillars at collapsed sites in Klip River coal field.......................................................................................................................58 Table 2-7 Summary...

  18. Coal transporting systems

    International Nuclear Information System (INIS)

    Vasilevski, Goce; Sazdov, Dushko; Tasevski, Apostol

    1999-01-01

    Installation of transporting systems in coal open pits in Macedonia was connected with construction and purchasing of the equipment from foreign companies. During 1998 Electric Power Company of Macedonia in connection with needs of the Oslomej Thermal Power Plant and delivery conditions,decided to give this task to domestic companies. This paper presents the planning activities an the implementation of the new coal transporting system. (Author)

  19. Improvements in monitoring coal

    International Nuclear Information System (INIS)

    Wright, H.R.C.; Tulloch, A.T.; Basterfield, A.

    1984-01-01

    An instrument for determining a first characteristic of a material, eg ash in coal, by X-radiation comprises a turntable with material feeding means. An X-radiation source and detector unit determines the first characteristic, and a microwave source and detector unit, determine a second characteristic of the material, eg moisture in coal. The turntable is transparent to microwaves in at least the region traversed by the microwaves. (author)

  20. Oil from coal

    Energy Technology Data Exchange (ETDEWEB)

    Thurlow, G.G.

    1978-10-01

    Our great-grandchildren will view the petroleum age as a brief perturbation in the life-style of mankind, less than a hundred years in which we discovered, exploited, squandered and exhausted the natural resource of liquid petroelum laid down over many million years of pre-history. What the sources of energy in common use in our great-grandchildren's day will be is something we cannot know. By then, the need for liquid hydrocarbon fuels may have passed. What is more sure, however, is that for a while, man will want to continue to use the equipment and the methods familiar to him from this petroleum-product dominated age beyond the time when natural petroleum sources become scarce. During these decades there will be a need to produce liquid hydrocarbons from other sources and one of these sources, abundantly available at this time, will be coal. Converting coal to liquid basically entails accomplishing two steps: (1) the separation of the coal substance from the ash and impurities associated with the coal, and (2) breaking down the complex coal molecules into simpler molecules and increasing the hydrogen-to-carbon ratio. It is also necessary, of course, to develop processes which will lead to the production of a range of liquid products to meet the demands of the commerical market, whether as fuels or as chemical feedstocks. Converting coal to a liquid needs energy, both heat and power, and hydrogen; if all these have to be generated starting from coal, their production may use approaching half of the Btu value of the coal fed to the plant. The economic advantage of one process over another will be mainly dependent on the products required and the price assigned to them and on the effectiveness with which the plant can be engineered to minimize energy loss and to operate effectively.

  1. The Evaluation of Efficiency of Polish Agriculture

    Directory of Open Access Journals (Sweden)

    Piotr Bórawski

    2015-01-01

    Full Text Available The objective of the paper was to recognize the efficiency of Polish agriculture. We have studied data from Main Statistical Office (MSO and compared the efficiency in the years 2000–2010. The data proved that the efficiency of Polish agriculture improved in the analyzed period. To measure the impact of macroeconomic variables we introduced these into the regression model. The macroeconomic factors included: X1 (nominal prices of land, X2 (land prices expressed in dt, X3 (inflation, X4 (investment in agriculture and hunting, X5 (balance of trade and X6 (GDP. We wanted to recognize the impact of macroeconomic factors on: Y1 (gross output, Y2 (intermediate consumption, Y3 (gross value added. Multiple regression was used to measure the impact of macroeconomic factors on global production of agriculture. The strongest impact on gross value added had: X4 (investment in agriculture and horticulture and X4 (trade balance. Poland is a member of European Union and the Common Agricultural Policy has improved the situation in agriculture. There are about 2 100 000 farms in Poland but only 300 000–400 000 are producing for the market. Other farms have social functions and are place for work for rural inhabitants.

  2. Food patterns of Polish older people

    DEFF Research Database (Denmark)

    Wadolowska, L.; Danowska-Oziewicz, M.; Niedzwiedzka, E.

    2006-01-01

    Food patterns of Polish older people were separated and described. The research included 422 people aged 65+ years, living in 5 geographical locations. Participants of the study were selected in quota sampling. Criteria for recruitment included sex, age (65-^74 or 75+ years) and family status (li...... and small number of products fonning joint food patterns speak in advocacy of relatively small reciprocal relationship between different food items consumed by the seniors in Poland.......Food patterns of Polish older people were separated and described. The research included 422 people aged 65+ years, living in 5 geographical locations. Participants of the study were selected in quota sampling. Criteria for recruitment included sex, age (65-^74 or 75+ years) and family status...... (living alone or living with other people). Respondents were asked questions about consumption of 55 food products. The factor analysis allowed for separating 21 food patterns. They included from 1 to 3 groups of products, intake of which was mutually dependant. Big number of separated food patterns...

  3. Farmers' pensions and the Polish economic crisis.

    Science.gov (United States)

    Simanis, J G

    1983-04-01

    The Polish Government, in 1977, inaugurated a new pension program that made old-age and invalidity benefits available for the first time to most farmers in that country. The evolution and eventual failure of that program were closely intertwined with a growing national economic crisis, manifested in widespread popular unrest and culminating in emergence of the Solidarity movement. The farmers' pension program was originally presented as both a social security measure and a vehicle for improving agricultural efficiency. The economic situation was expected to benefit as farms of older owners were passed to younger, presumably more efficient, successors, with the state sometimes acting as intermediary. A further step to bind the social security concept to agricultural efficiency came through relating the pension amount to the quantity of produce the individual farmer sold to the state over a number of years. The failure of these provisions and other unpopular features of the new program was aggravated by inflation and continuing deterioration of the Polish economy.

  4. Robotic Automation in Computer Controlled Polishing

    Science.gov (United States)

    Walker, D. D.; Yu, G.; Bibby, M.; Dunn, C.; Li, H.; Wu, Y.; Zheng, X.; Zhang, P.

    2016-02-01

    We first present a Case Study - the manufacture of 1.4 m prototype mirror-segments for the European Extremely Large Telescope, undertaken by the National Facility for Ultra Precision Surfaces, at the OpTIC facility operated by Glyndwr University. Scale-up to serial-manufacture demands delivery of a 1.4 m off-axis aspheric hexagonal segment with surface precision use of robots to automate currently-manual operations on CNC polishing machines, to improve work-throughput, mitigate risk of damage to parts, and reduce dependence on highly-skilled staff. Second is the use of robots to pre-process surfaces prior to CNC polishing, to reduce total process time. The third draws the threads together, describing our vision of the automated manufacturing cell, where the operator interacts at cell rather than machine level. This promises to deliver a step-change in end-to-end manufacturing times and costs, compared with either platform used on its own or, indeed, the state-of-the-art used elsewhere.

  5. Integrated coal preparation

    International Nuclear Information System (INIS)

    Buchanan, D.J.; Jones, T.F.

    1992-01-01

    Perceptions of quality have changed over the years. The attributes of a certain coal (its rank, slagging propensity, ash content etc) are traditionally referred to as its quality. However, the subject of this paper is quality in a much wider sense: quality as fitness for purpose: and all that such a wide definition entails. British Standard BS 5750 (ISO 9000) Quality Systems defines a systems approach to quality, and includes both the supplier of raw materials and the final customer within this boundary. Coal preparation starts at the production face. The greater the proportion of dirt in run-of-mine product the greater the challenge in satisfying the customer's needs. Significant advances have been made in minimizing mined dirt. For example, the sue of vertical steering on longwall faces improves productivity and quality. Unfortunately modern mining methods produce large quantities of fines, despite efforts to reduce them at the point of production and during transportation to the surface. Coal preparation also produces further fines. It has been estimated that fine coal costs 2.5 times as much to clean as large coal, and the costs of handing wet fine coal product will inflate this estimate. Handling considerations rightly concern our customers and are part of the wider meaning of quality. In this paper the authors address some novel solutions to the challenge posed by fines

  6. Analytic tendencies in modern Polish and Russian

    Directory of Open Access Journals (Sweden)

    Wojciech Sosnowski

    2015-11-01

    Full Text Available Analytic tendencies in modern Polish and Russian Modern Polish and Russian are characterized by some features which demonstrate an increasing level of analitism. In the process of transformation from synthetic to analytical language, a crucial role is played by prepositional units. In this research, analitism is understood in a traditional way as a morphological and syntactic phenomenon. The fact that the synthetic structure of a language may, in some conditions, turn into an analytical one, as happened in the case of Bulgarian and Macedonian, has been intriguing linguists ever since, and has made me attempt to answer the question: What is the condition of modern Polish and Russian, which are languages with a rich literary tradition and solid grammatical norms, which belong to a group of synthetic languages? The analytical tendencies in morphology include the following: a decrease in the number of cases in all inflected parts of speech; a more frequent use of uninflected nouns and adjectives; the growing importance of nouns with common gender, and, in particular, the use of forms of masculine gender to depict feminine gender; differences in expressing collectiveness in a group of nouns (using collective meaning for forms that have singular meaning; substituting case forms with prepositions; substituting case forms with subordinate clauses; substituting case forms with “helper” words. Analytical tendencies in the area of numeral functioning include: substituting inflected forms of ordinal numerals with cardinal ones; the gradual disappearing inflection of numerals; confusing the forms of noun cases after numerals; the disappearing declination of collective numerals; displacing other cases with so-called simple cases; changing the syntactical position which the numeral should be inflected in; abandoning the declination of first elements of collective numerals. During the study of analytic tendencies in morphology, it was necessary to examine

  7. Prospects for coal and clean coal technology in the Philippines

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2013-03-15

    This report examines the current energy outlook for the Philippines in regard not only to coal but also other energy resources. The history of the power sector, current state of play and future plans to meet the increasing energy demand from a growing population are discussed. There is also analysis of the trends for coal demand and production, imports and exports of coal and the types of coal-fired power stations that have been built. This includes examination of the legislation involving coal and the promotion of clean coal technologies.

  8. Global Citizenship Education in School Curricula. A Polish Perspective

    Science.gov (United States)

    Leek, Joanna

    2016-01-01

    The purpose of this study is to present global citizenship education from a Polish perspective. Analyzing the issue, the first part of this paper presents the development of citizenship education, followed by the current status of global citizenship education in Polish schools. In the second part of the study I draw attention to national curricula…

  9. Comparative study of performance of shoe polishes formulated from ...

    African Journals Online (AJOL)

    Polyethylene pigment was generated from “pure water sachets” (one of the major environmental nuisance today) and used in the formulation of shoe polish using paraffin wax, white spirit, turpentine oil, and nitrocellulose. The polish was found to exhibit similar wrinkle resistance, inferior gloss, rub resistance; resistance to ...

  10. Polish anthropology on the eve of the new millennium

    OpenAIRE

    Drozdowski, Zbigniew

    1999-01-01

    Author summarizes the main achievements of Polish anthropology in the 20th century, presents the main research problems of this discipline in contemporary Poland and points at the potential dangers which may be faced by Polish anthropology in the forthcoming years.

  11. Influence of melt treatments and polished CVD diamond coated ...

    Indian Academy of Sciences (India)

    Performances of the turning inserts (uncoated and polished CVD diamond coated) were evaluated in machining Al–7Si and Al–7Si–2.5Cu cast alloys under dry environment using a lathe. The polished CVD diamond coated insert outperformed the uncoated cutting insert which suffered from sizeable edge buildup leading to ...

  12. Social Obstacles Towards Success of Pupils in Polish Primary Schools.

    Science.gov (United States)

    Nakielska, Zofia

    In 1973, the Polish Minister of Education ordered objective competitions at the primary school level in the fields of Polish studies, Russian language, and math. In order to determine whether such subject competitions were justified and if they contributed equally to the development of interests and abilities among the rural and urban and…

  13. Etymology in the Polish Academy of Sciences Great Dictionary of ...

    African Journals Online (AJOL)

    The article offers an insight into etymological information provided in the Polish Academy of Sciences Great Dictionary of Polish (Pol. Wielki słownik języka polskiego PAN, WSJP PAN). The dictionary and the rules of producing the entries are briefly presented. These rules influence the way of working on etymology within ...

  14. The Czechoslovak-Polish Club in Brno (1925–1939)

    Czech Academy of Sciences Publication Activity Database

    Baron, Roman

    2011-01-01

    Roč. 3, č. 1 (2011), s. 43-64 ISSN 1803-6546 Institutional research plan: CEZ:AV0Z80150510 Keywords : Czechoslovak-Polish solidarity * Czechoslovak-Polish relations * Brno * associations * Interwar Period Subject RIV: AB - History

  15. Coal market outlook in China

    International Nuclear Information System (INIS)

    Yu Zhufeng; Zheng Xingzhou

    2005-01-01

    Coal is the major primary energy source in China. It is forecast that coal will account for over 60% of the primary energy consumption mix, and the total coal demand will reach 2.3-2.9 billion tons in 2020. However, ensuring the coal supply will be faced with a lot of obstacles in fields such as the degree of detailed exploration of coal reserves, the level of mining technology and mine safety, the production capacity building of mines, transport conditions, and ecological and environmental impacts. More comprehensive measures should be adopted, including improvements in energy efficiency, strengthening coal production and transportation capacity, to rationalise coal mine disposition and the coal production structure, and to raise the levels of coal mining technologies and mine safety management, etc. (author)

  16. Coal recovery from a coal waste dump

    Directory of Open Access Journals (Sweden)

    Rozanski Zenon

    2016-01-01

    Full Text Available The possibilities and efficiency of coal recovery from the waste material located at the Central Coal Waste Dump in Poland were presented in this paper. The waste material includes significant amount of fly ash. Research conducted into determination of energetic properties of such wastes showed that the average ash content was 75.75% and the average gross calorific value was 7.81 MJ/kg. Coal was gravitationally separated from the waste material in a pulsatory jig and in a spiral washer including size fractions: 30-5 and 8-0 mm (this was crushed to a size <3.2 mm, respectively. The application of the pulsatory jig (pulse classifier allowed to obtain a high-quality energetic concentrate with the ash content lower than 12% and the gross calorific value higher than 26 MJ/kg (with average yield 7.8%. The spiral separator gave much worse results. The average gross calorific value for the concentrate was 11.6 MJ/kg, with the high ash content 56.5% and yield approximately 26%.

  17. Trace elements in coal ash

    Science.gov (United States)

    Deonarine, Amrika; Kolker, Allan; Doughten, Michael W.

    2015-01-01

    Coal ash is a residual waste product primarily produced by coal combustion for electric power generation. Coal ash includes fly ash, bottom ash, and flue-gas desulfurization products (at powerplants equipped with flue-gas desulfurization systems). Fly ash, the most common form of coal ash, is used in a range of products, especially construction materials. A new Environmental Protection Agency ruling upholds designation of coal ash as a non-hazardous waste under Subtitle D of the Resource Conservation and Recovery Act, allowing for the continued beneficial use of coal ash and also designating procedures and requirements for its storage.

  18. EIA projections of coal supply and demand

    International Nuclear Information System (INIS)

    Klein, D.E.

    1989-01-01

    Contents of this report include: EIA projections of coal supply and demand which covers forecasted coal supply and transportation, forecasted coal demand by consuming sector, and forecasted coal demand by the electric utility sector; and policy discussion

  19. Variability of Mercury Content in Coal Matter From Coal Seams of The Upper Silesia Coal Basin

    Science.gov (United States)

    Wierzchowski, Krzysztof; Chećko, Jarosław; Pyka, Ireneusz

    2017-12-01

    The process of identifying and documenting the quality parameters of coal, as well as the conditions of coal deposition in the seam, is multi-stage and extremely expensive. The taking and analyzing of seam samples is the method of assessment of the quality and quantity parameters of coals in deep mines. Depending on the method of sampling, it offers quite precise assessment of the quality parameters of potential commercial coals. The main kind of seam samples under consideration are so-called "documentary seam samples", which exclude dirt bands and other seam contaminants. Mercury content in coal matter from the currently accessible and exploited coal seams of the Upper Silesian Coal Basin (USCB) was assessed. It was noted that the mercury content in coal seams decreases with the age of the seam and, to a lesser extent, seam deposition depth. Maps of the variation of mercury content in selected lithostratigraphic units (layers) of the Upper Silesian Coal Basin have been created.

  20. The Government’s Policy in the Field of Hard Coal Mining Restructuration as an Element of Poland’s Energy Security

    Directory of Open Access Journals (Sweden)

    Małgorzata Kamola-Cieślik

    2017-12-01

    Full Text Available Coal is the primary energy source affecting Poland’s energy security. It is because deposits of this raw material are available in Poland. Unlike natural gas or oil reserves, which are limited in the country. The high cost of extracting Polish coal in comparison with coal prices on the world market has made it necessary to adopt Polish mining to functioning in market economy conditions. The paper presents the evolution of Polish government policy towards the activity of coal mines in the years 1990–2015. This article aims to present government policy on restructuring coal mining after 2015 and showing its effects. The stages of consolidation of the power industry with the mining industry are shown. The above issues are presented in the context of the European Union’s energy and climate policy, paying particular attention to the share of renewable energy sources in the energy and fuel balance and the reduction of carbon dioxide emissions into the atmosphere.

  1. Chemical mechanical polishing (CMP) of sapphire

    Science.gov (United States)

    Zhu, Honglin

    The concept of chemical mechanical polishing (CMP) was examined for finishing sapphire. In this study sapphire was used as a model system for oxide ceramics. The removal rates were determined by weight loss. Surface quality and structure were characterized with surface probe microscopy (SPM). Polishing experiments were designed to test the chemically modified surface layer. A series of abrasives with various hardnesses including mono-crystalline and polycrystalline diamond, alpha and gamma alumina, zirconia, ceria and silica were used. Diaspore was also evaluated. The results indicated that, with similar particle size and shape, harder abrasives do not necessarily cause faster material removal and better surface finish, and abrasives with hardness equal to or less than sapphire such as alpha alumina and gamma alumina achieved the best surface finish and efficient material removal. A hypothesis was proposed that the sapphire surface was modified by water to form a thin hydration laver with structure and hardness close to diaspore. Abrasives with a hardness between diaspore and sapphire polished the c-plane of sapphire with good surface finish and efficient removal. SPM indicated the hydration layer on the c-plane surface was about 1 nm thick. Removal rate and surface finish as a function of pH were also examined on c-plane sapphire with nano-alumina abrasives. The removal rate as a function of pH was compared to the solubility behavior of alumina. The results showed the deviation of pH from the lowest solubility pH for alumina (pH = 5) was a driving force for the surface reaction to form a hydration layer. The anisotropy of sapphire strongly affects removal rate and surface quality in CMP. The relationships among orientation. pH and abrasive were studied for sapphire with c (0001), a (11-20), and m (10-10) planes. Based on the results, the CMP process for sapphire includes chemical reaction of the surface to form a thin reaction layer that is softer than sapphire

  2. 11th annual conference on clean coal technology, proceedings

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-07-01

    Topics covered at the conference include coal combustion technology, multi-purpose coal conversion technology (including entrained-bed coal flash pyrolysis process (CPX), hydrogen production from coal and coal liquefaction), coal ash utilization technology, next general technology (including dry coal cleaning technologies and coal conversion by supercritical water) and basic coal utilization technology (including ash behaviour during coal gasification).

  3. Coal: geology, resources and reserves. Political economy of mineral coal

    International Nuclear Information System (INIS)

    Allegre, Maurice; Martin-Amouroux, Jean-Marie

    2014-04-01

    A first article indicates the different types of coal (lignite, coking coal, thermal coal) and their calorific power. The author discusses the geology and genesis of coal, and then evokes the various extraction techniques. He comments the definition used regarding resources and reserves, comments various resource assessments, and discusses the future evolution of resources and reserves. He comments the consequences of coal geology for perspectives and costs of production. The second article comments the strong increase of World coal consumption since 1980 (a table is given with data for each continent), outlines that thermoelectricity is the engine of coal demand, that extraction costs and transport costs remained limited (when extraction costs become too high, the mining site is generally closed). The author comments the development of international trade on very competitive markets, and outlines that national coal policies are much different among countries

  4. What component of coal causes coal workers' pneumoconiosis?

    Science.gov (United States)

    McCunney, Robert J; Morfeld, Peter; Payne, Stephen

    2009-04-01

    To evaluate the component of coal responsible for coal workers' pneumoconiosis (CWP). A literature search of PubMED was conducted to address studies that have evaluated the risk of CWP based on the components of coal. The risk of CWP (CWP) depends on the concentration and duration of exposure to coal dust. Epidemiology studies have shown inverse links between CWP and quartz content. Coal from the USA and Germany has demonstrated links between iron content and CWP; these same studies indicate virtually no role for quartz. In vitro studies indicate strong mechanistic links between iron content in coal and reactive oxygen species, which play a major role in the inflammatory response associated with CWP. The active agent within coal appears to be iron, not quartz. By identifying components of coal before mining activities, the risk of developing CWP may be reduced.

  5. Leachability of trace elements in coal and coal combustion wastes

    International Nuclear Information System (INIS)

    Rice, C.A.; Breit, G.N.; Fishman, N.S.; Bullock, J.H. Jr.

    1999-01-01

    Leaching of trace elements from coal and coal combustion waste (CCW) products from a coal-fired power plant, burning coal from the Appalachian and Illinois basins, was studied using deionized (DI) water as a lixiviant to resemble natural conditions in waste disposal sites exposed to dilute meteoric water infiltration. Samples of bottom ash, fly ash, and feed coal were collected from two combustion units at monthly intervals, along with a bulk sample of wastes deposited in an on-site disposal pond. The units burn different coals, one a high-sulfur coal (2.65 to 3.5 weight percent S) and the other, a low-sulfur coal (0.6--0.9 eight percent S). Short-term batch leaches with DI water were performed for times varying from a few minutes to 18 hours. Select fly ash samples were also placed in long-term (> 1 year) flow-through columns

  6. Co-Processing Coal and Natural Gas by the Hynol Process for Enhanced Methanol Production and Reduced CO2 Emissions

    National Research Council Canada - National Science Library

    Steinberg, Meyer

    1997-01-01

    ...) catalytic methanol synthesis. The Hynol Process is a total recycle process. Using a process simulation computer program, mass and energy balances and yields and efficiency data have been obtained for a range of natural gas to coal feedstock ratios...

  7. Mill performance of coal blends

    Energy Technology Data Exchange (ETDEWEB)

    P.A. Bennett; G. O' Brien; D. Holcombe [CoalTech Pty Ltd. (Australia)

    2005-07-01

    Evaluating the potential performance of coal blends for use as pulverised fuel (PF) in power plants and pulverised coal injection (PCI) into blast furnaces requires knowledge of the size distribution of the organic and mineral matter components of a blend, especially when there are significant differences in the Hardgrove Grindability Index (HGI) of the component coals. The size distribution of the organic matter impacts on combustibility of thermal and PCI coal blends and handleability of PCI coal blends. Petrography techniques were used to examine four size fractions from the PF of single coals and blends to measure the size distribution of maceral groups. For most coals, a good estimate of a blend's size distribution can be made assuming that the size distribution of the individual coals, milled under the same conditions, are added together in the proportions of the blend. The exception is when a very soft coal (HGI 90) is blended with a very hard coal (HGI 35). In this case preferential milling (more reporting to the smaller size fractions) of the softer coal occurred. All coals studied in this project show some sign of preferential grinding of the softer maceral group when the coal was milled individually or in a blend. It is only when there is a large difference in the relative strength of the maceral groups of the coals blended that the preferential milling of a coal in a blend is observed in the size distribution of the blend. The results indicate that the breakage characteristics (change in size reduction per unit of energy) of maceral groups in individual coals do not change when they are blended with other coals. 12 refs., 5 figs., 2 tabs.

  8. Global thermal coal trade outlook

    International Nuclear Information System (INIS)

    Ewart, E.

    2008-01-01

    Wood Mackenzie operates coal consulting offices in several cities around the world and is the number one consulting company in terms of global coal coverage. The company offers a unique mine-by-mine research methodology, and owns a proprietary modeling system for coal and power market forecasting. This presentation provided an overview of global thermal markets as well as recent market trends. Seaborne markets have an impact on price far greater than the volume of trade would imply. Research has also demonstrated that the global thermal coal market is divided between the Pacific and Atlantic Basins. The current status of several major coal exporting countries such as Canada, the United States, Venezuela, Colombia, Indonesia, Australia, China, South Africa, and Russia was displayed in an illustration. The presentation included several graphs indicating that the seaborne thermal coal market is highly concentrated; traditional coal flow and pricing trends shift as Asian demand growth and supply constraints lead to chronic under supply; coal prices have risen to historic highs in recent times; and, the Asian power sector demand is a major driver of future growth. The correlation between oil and gas markets to thermal coal was illustrated along with two scenarios of coal use in the United States in a carbon-constrained world. The impact of carbon legislation on coal demand from selected coal regions in the United States was also discussed. Wood Mackenzie forecasts a very strong growth in global thermal coal demand, driven largely by emerging Asian economies. tabs., figs

  9. Regional Differences in Demand for Coal as A Basis for Development of A Product Distribution Model for Mining Companies in the Individual Customers Segment

    Science.gov (United States)

    Magda, Roman; Bogacz, Paweł; Franik, Tadeusz; Celej, Maciej; Migza, Marcin

    2014-10-01

    The article presents a proposal of methodology based on the process of relationship marketing, serving to determine the level of demand for coal in the individual customer segment, as well as fuel distribution model for this customer group in Poland developed on the basis of this methodology. It also includes selected results of tests carried out using the proposed methods. These proposals have been defined on the basis of market capacity indicators, which can be determined for the district level based on data from the Polish Central Statistical Office. The study also included the use of linear programming, based on the cost of coal logistics, data concerning railway, road and storage infrastructure present on the Polish market and taking into account the legal aspects. The presented results may provide a basis for mining companies to develop a system of coal distribution management in the locations with the highest demand values.

  10. Brewing test with puffed polished rice. : Sake brewing with puffed polished rive (II)

    OpenAIRE

    家村, 芳次; 永田, 興四郎; 田端, 昇; 佐無田, 隆; 吉沢, 淑; YOSHITSUGU, IEMURA; KOSHIROU, NAGATA; NOBORU, TABATA; TAKASHI, SAMUTA; KIYOSHI, YOSHIZAWA; 菊正宗酒造株式会社; 山邑酒造株式会社; 灘五郷酒造組合; 熊本国税局鑑定官室; 国税庁醸造試験所

    1985-01-01

    Polished rice was puffed by continuous puffing equipment, then part of it was contracted under a vapor stream. These samples were used for sake brewing.Fermentation took place normally in very tested mash. Each sake produced differed slightly in alcohol concentration, nihonshudo, and acidity; they differed greatly in the content of amino acids, with that of sake made from puffed rice was lower than that of sake made from steamed rice, and that of sake made from contracted rice after puffing t...

  11. Plurilingualism and polish teenage learners of english

    Directory of Open Access Journals (Sweden)

    Agnieszka Otwinowska‑Kasztelanic

    2012-01-01

    Full Text Available Using several languages has become a norm for those who want to learn and work in the European Union. However, teaching for plurilingualism is also a challenge. The present paper first clarifies the notions of plurilingualism and multilingualism, then discusses the role of crosslinguistic similarity in language learning in the case of European languages. It also shows how lexical crosslinguistic similarity can be used in teaching typologically related and unrelated languages, and discusses the key factors in noticing such similarity. The research presented reports on examining and raising language awareness of Polish‑‑ English cognate vocabulary in the case of a group of Polish teenage learners of English. It presents the results of a small‑‑ scale study in quasi‑‑ experimental design, as well as qualitative research on the learners’ opinions and attitudes. Finally, the paper presents implications for language pedagogy and focuses on the fact that awareness raising may affect the learners’ plurilingual competence.

  12. Antigenic typing Polish isolates of canine parvovirus

    Energy Technology Data Exchange (ETDEWEB)

    Mizak, B. [National Veterinary Research Institute, Pulawy (Poland); Plucienniczak, A. [Polish Academy ofd Sciences. Microbiology and Virology Center, Lodz (Poland)

    1995-12-31

    Polish strains of canine parvovirus isolated between 1982 and 1993 were examined to determine the extent to which the virus has evolved antigenically and genetically over eleven years. Two CPV isolates obtained in Warsaw in 1982 and Pulawy in 1993, were examined using monoclonal antibody typing, restriction analysis and sequencing VP-2 protein gene. Five other isolates from Warsaw and Pulawy were tested with the panel of monoclonal antibodies specific to CPV-2, CPV-2a and common for canine parvovirus, feline panleukopenia virus and milk enteritis virus. Results of the studies demonstrated that all isolates tested represented CPV-2a antigenic type. Rapid antigenic strain replacement recorded by Parrish and Senda in the U.S.A and Japan was not confirmed in Poland. (author). 30 refs, 2 tabs.

  13. Attitudes of Polish Consumers Toward Experiential Marketing

    Directory of Open Access Journals (Sweden)

    Monika Skorek

    2017-01-01

    Full Text Available Purpose: The experience economy is a concept that can be defned as a new way of perceiving the market offer of an enterprise, focusing on the customer experience. Enterprises, both in the production and service industries, are becoming similar to one another on a massive scale, which makes it increasingly diffcult to stand out. The response to this can be to offer the consumer an unforgettable experience related to a product or service provided by a company. Methodology: This study analysed the results of qualitative research on the attitudes and opinions of Polish consumers on experience marketing. Results/fndings: The results showed that participants of the study were prepared to transition from the economy based on products or services to an economy based on experiences at a moderate level. They declared a willingness to participate in experiences offered by companies but at the same time focus on the cost and utility of them

  14. Reducing noise levels in coal cleaning plants and in briquetting plants

    Energy Technology Data Exchange (ETDEWEB)

    Niechoroszyj, I.C.; Zurbinskij, L.F.

    1979-11-01

    In the case of production plants using various technologies, various machines and changing location of machines and installations there can not be a unified method of noise reduction; rather each type of machine should be treated separately. The following methods of noise reduction are enumerated: for coal screens - the screen can be covered with noise supressing materials, or rubber screens can be used instead of steel screens; during dry grading of coal dustproof and soundproof shields should be used; the same method can be used in the case of coal crushing machines; for pumps and air fans the noise level can be reduced by proper installation and lubrication. The most noisy machines should be located in separate rooms. Special screens made of rubber can also be used which can reduce noise levels by 10 decibels. (3 refs.) (In Polish)

  15. Chemical looping coal gasification with calcium ferrite and barium ferrite via solid–solid reactions

    International Nuclear Information System (INIS)

    Siriwardane, Ranjani; Riley, Jarrett; Tian, Hanjing; Richards, George

    2016-01-01

    Highlights: • BaFe 2 O 4 and CaFe 2 O 4 are excellent for chemical looping coal gasification. • BaFe 2 O 4 and CaFe 2 O 4 have minimal reactivity with synthesis gas. • Steam enhances the gasification process with these oxygen carriers. • Reaction rates of steam gasification of coal with CaFe 2 O 4 was better than with gaseous oxygen. • Coal gasification appears to be via solid–solid interaction with the oxygen carrier. - Abstract: Coal gasification to produce synthesis gas by chemical looping was investigated with two oxygen carriers, barium ferrite (BaFe 2 O 4 ) and calcium ferrite (CaFe 2 O 4 ). Thermo-gravimetric analysis (TGA) and fixed-bed flow reactor data indicated that a solid–solid interaction occurred between oxygen carriers and coal to produce synthesis gas. Both thermodynamic analysis and experimental data indicated that BaFe 2 O 4 and CaFe 2 O 4 have high reactivity with coal but have a low reactivity with synthesis gas, which makes them very attractive for the coal gasification process. Adding steam increased the production of hydrogen (H 2 ) and carbon monoxide (CO), but carbon dioxide (CO 2 ) remained low because these oxygen carriers have minimal reactivity with H 2 and CO. Therefore, the combined steam–oxygen carrier produced the highest quantity of synthesis gas. It appeared that neither the water–gas shift reaction nor the water splitting reaction promoted additional H 2 formation with the oxygen carriers when steam was present. Wyodak coal, which is a sub-bituminous coal, had the best gasification yield with oxygen carrier–steam while Illinois #6 coal had the lowest. The rate of gasification and selectivity for synthesis gas production was significantly higher when these oxygen carriers were present during steam gasification of coal. The rates and synthesis gas yields during the temperature ramps of coal–steam with oxygen carriers were better than with gaseous oxygen.

  16. Bright outlook for coal

    International Nuclear Information System (INIS)

    Anon

    2001-01-01

    After enduring contract price cuts over the past two years of almost 17% for thermal coal and 23% for hard coking coal, the New South Wales coal industry is looking forward to a reversal of fortune for 2001. Increased export demand, improved prices, significant improvements in mine site productivity, a weak Australian dollar and the probability of a number of new projects or extensions progressing to development are likely to result in an increase in NSW saleable production to around 110 million tonnes (Mt) in 2000-01. Sharply weaker coal prices over the past two years, intensified international competition and the Asian economic downturn had a negative impact on profitability, investment, exports and employment in the NSW coal industry. As a result, the industry has undergone substantial restructuring. The restructuring process has led to a consolidation in ownership, reduced production costs and improved operational efficiency. The outcome is an industry well positioned to take advantage of the positive market conditions and one likely to experience levels of profitability not achieved over the past few years

  17. Coal processing plants

    Science.gov (United States)

    Bitterlich, W.; Bohn, T.; Eickhoff, H. G.; Geldmacher, H.; Mengis, W.; Oomatia, H.; Stroppel, K. G.

    1980-08-01

    The efficient design of processing plants which combine various coal based technologies in order to maximize the effectiveness of coal utilization is considered. The technical, economical and ecological virtues which compound plants for coal conversion offer are assayed. Twenty-two typical processes of coal conversion and product refinement are selected and described by a standardized method of characterization. An analysis of product market and a qualitative assessment of plant design support six different compound plant propositions. The incorporation of such coal conversion schemes into future energy supply systems was simulated by model calculations. The analysis shows that byproducts and nonconverted materials from individual processes can be processed in a compound plant in a profitable manner. This leads to an improvement in efficiencies. The product spectrum can be adapted to a certain degree to demand variations. Furthermore, the integration of fluidized bed combustion can provide an efficient method of desulfurization. Compound plants are expected to become economic in the 1990's. A necessary condition to compound technologies is high reliability in the functioning of all individual processes.

  18. Coal production, 1991

    International Nuclear Information System (INIS)

    1992-10-01

    Coal production in the United States in 1991 declined to a total of 996 million short tons, ending the 6-year upward trend in coal production that began in 1985. The 1991 figure is 33 million short tons below the record level of 1.029 billion short tons produced in 1990 (Table 1). Tables 2 through 33 in this report include data from mining operations that produced, prepared, and processed 10,000 or more short tons during the year. These mines yielded 993 million short tons, or 99.7 percent of the total coal production in 1991, and their summary statistics are discussed below. The majority of US coal (587 million short tons) was produced by surface mining (Table 2). Over half of all US surface mine production occurred in the Western Region, though the 60 surface mines in this area accounted for only 5 percent of the total US surface mines. The high share of production was due to the very large surface mines in Wyoming, Texas and Montana. Nearly three quarters of underground production was in the Appalachian Region, which accounted for 92 percent of underground mines. Continuous mining methods produced the most coal among those underground operations that responded. Of the 406 million short tons, 59 percent (239 million short tons) was produced by continuous mining methods, followed by longwall (29 percent, or 119 million short tons), and conventional methods (11 percent, or 46 million short tons)

  19. Clean coal technology

    International Nuclear Information System (INIS)

    Abelson, P.H.

    1990-01-01

    One of the major technology challenges in the next decade will be to develop means of using coal imaginatively as a source of chemicals and in a more energy-efficient manner. The Clean Air Act will help to diminish the acid rain but will not reduce CO 2 emissions. The Department of Energy (DOE) is fostering many innovations that are likely to have a positive effect on coal usage. Of the different innovations in the use of coal fostered by DOE, two are of particular interest. One is the new pressurized fluid bed combustion (PFBC) combined-cycle demonstration. The PFBC plant now becoming operational can reduce SO 2 emissions by more than 90% and NO x emissions by 50-70%. A second new technology co-sponsored by DOE is the Encoal mild coal gasification project that will convert a sub-bituminous low-BTU coal into a useful higher BTU solid while producing significant amounts of a liquid fuel

  20. Coal liquefaction processes

    Energy Technology Data Exchange (ETDEWEB)

    Baker, N.R.; Blazek, C.F.; Tison, R.R.

    1979-07-01

    Coal liquefaction is an emerging technology receiving great attention as a possible liquid fuel source. Currently, four general methods of converting coal to liquid fuel are under active development: direct hydrogenation; pyrolysis/hydrocarbonization; solvent extraction; and indirect liquefaction. This work is being conducted at the pilot plant stage, usually with a coal feed rate of several tons per day. Several conceptual design studies have been published recently for large (measured in tens of thousands of tons per day coal feed rate) commercial liquefaction plants, and these reports form the data base for this evaluation. Products from a liquefaction facility depend on the particular method and plant design selected, and these products range from synthetic crude oils up through the lighter hydrocarbon gases, and, in some cases, electricity. Various processes are evaluated with respect to product compositions, thermal efficiency, environmental effects, operating and maintenance requirements, and cost. Because of the large plant capacities of current conceptual designs, it is not clear as to how, and on what scale, coal liquefaction may be considered appropriate as an energy source for Integrated Community Energy Systems (CES). Development work, both currently under way and planned for the future, should help to clarify and quantify the question of applicability.

  1. Coal fire interferometry

    International Nuclear Information System (INIS)

    Van Genderen, J.L.; Prakash, A.; Gens, R.; Van Veen, B.; Liding, Chen; Tao, Tang Xiao; Feng, Guan

    2000-07-01

    This BCRS project demonstrates the use of SAR interferometry for measuring and monitoring land subsidence caused by underground coal fires and underground mining in a remote area of north west China. China is the largest producer and consumer of coal in the world. Throughout the N.W., N. and N.E. of China, the coal-seams are very susceptible to spontaneous combustion, causing underground coal fires. As the thick coal seams are burned out, the overburden collapses, causing land subsidence, and producing new cracks and fissures, which allow more air to penetrate and continue the fire to spread. SAR interferometry, especially differential interferometry has been shown to be able to measure small differences in surface height caused by such land subsidence. This report describes the problems, the test area, the procedures and techniques used and the results obtained. It concludes with a description of some of the problems encountered during the project plus provides some general conclusions and recommendations. 127 refs

  2. Droughts in historical times in Polish territory

    Science.gov (United States)

    Limanowka, Danuta; Cebulak, Elzbieta; Pyrc, Robert; Doktor, Radoslaw

    2015-04-01

    Climate change is one of the key environmental, social and economical issues, and it is also followed by political consequences. Impact of climate conditions on countries' economy is increasingly recognized, and a lot of attention is given, both in the global scale and by the individual national governments. In years 2008-2010, at the Poland -Institute of Meteorology and Water Management-National Research Institute was realized the KLIMAT Project on Impact of climate change on environment, economy and society (changes, effects and methods of reducing them, conclusions for science, engineering practice and economic planning) No. POIG01-03-01-14-011/08. The project was financed by the European Union and Polish state budget in frame of Innovative Economy Operational Programme. A very wide range of research was carried out in the different thematic areas. One of them was "Natural disasters and internal safety of the country (civil and economical)." The problem of drought in Poland was developed in terms of meteorology and hydrology. "Proxy" Data Descriptions very often inform about dry years and seasons, hot periods without precipitation. Analysis of historical material allowed to extract the years that have experienced prolonged periods of high temperatures and rainfall shortages. Weather phenomenon defined as drought belongs to extreme events. This information was very helpful in the process of indexing and thus to restore the course and intensity of climatic elements in the past. The analysis covered the period from year 1000 to modern times. Due to the limited information from the period of 1000-1500 the authors focused primarily on the period from 1500 to 2010. Analysis of the collected material has allowed the development of a highly precise temporal structure of the possible occurrence of dry periods to Polish territory.

  3. Thermodynamic analyses of solar thermal gasification of coal for hybrid solar-fossil power and fuel production

    International Nuclear Information System (INIS)

    Ng, Yi Cheng; Lipiński, Wojciech

    2012-01-01

    Thermodynamic analyses are performed for solar thermal steam and dry gasification of coal. The selected types of coal are anthracite, bituminous, lignite and peat. Two model conversion paths are considered for each combination of the gasifying agent and the coal type: production of the synthesis gas with its subsequent use in a combined cycle power plant to generate power, and production of the synthesis gas with its subsequent use to produce gasoline via the Fischer–Tropsch synthesis. Replacement of a coal-fired 35% efficient Rankine cycle power plant and a combustion-based integrated gasification combined cycle power plant by a solar-based integrated gasification combined cycle power plant leads to the reduction in specific carbon dioxide emissions by at least 47% and 27%, respectively. Replacement of a conventional gasoline production process via coal gasification and a subsequent Fischer–Tropsch synthesis with gasoline production via solar thermal coal gasification with a subsequent Fischer–Tropsch synthesis leads to the reduction in specific carbon dioxide emissions by at least 39%. -- Highlights: ► Thermodynamic analyses for steam and dry gasification of coal are presented. ► Hybrid solar-fossil paths to power and fuels are compared to those using only combustion. ► Hybrid power production can reduce specific CO 2 emissions by more than 27%. ► Hybrid fuel production can reduce specific CO 2 emissions by more than 39%.

  4. Exchange of experience: sieve analyses of coal and coal paste

    Energy Technology Data Exchange (ETDEWEB)

    1943-02-01

    This report consisted of a cover letter (now largely illegible) and a graph. The graph showed percentages of material left behind as residue on sieves of various mesh sizes, graphed against the mesh sizes themselves. The materials for which data were shown were both dry coal and coal paste from Ludwigshafen, Scholven, Gelsenberg, and Poelitz. The dry coal from Poelitz seemed to be by far the least finely-ground, but the coal paste from Poelitz seemed to be the most finely-ground. The values for coal paste from the other three plants were very close together over most of the range of mesh sizes. The dry coal from Gelsenberg seemed to be the most finely-ground dry coal, while the dry coals from Scholven and Ludwigshafen gave similar values over most of the range of mesh sizes. In all cases, the coal paste from a plant was more finely-ground than the dry coal from the same plant, but for Gelsenberg, the difference between the two was not nearly as great as it was for the other plants, especially Poelitz. For example, for a sieve with about 3,600 cells per square centimeter, only about 10% of the Poelitz coal paste was retained versus about 85% of the Poelitz dry coal retained, whereas the corresponding figures for Gelsenberg materials were about 36% versus about 53%.

  5. Low-rank coal research

    Energy Technology Data Exchange (ETDEWEB)

    Weber, G. F.; Laudal, D. L.

    1989-01-01

    This work is a compilation of reports on ongoing research at the University of North Dakota. Topics include: Control Technology and Coal Preparation Research (SO{sub x}/NO{sub x} control, waste management), Advanced Research and Technology Development (turbine combustion phenomena, combustion inorganic transformation, coal/char reactivity, liquefaction reactivity of low-rank coals, gasification ash and slag characterization, fine particulate emissions), Combustion Research (fluidized bed combustion, beneficiation of low-rank coals, combustion characterization of low-rank coal fuels, diesel utilization of low-rank coals), Liquefaction Research (low-rank coal direct liquefaction), and Gasification Research (hydrogen production from low-rank coals, advanced wastewater treatment, mild gasification, color and residual COD removal from Synfuel wastewaters, Great Plains Gasification Plant, gasifier optimization).

  6. Viscosity Depressants for Coal Liquefaction

    Science.gov (United States)

    Kalfayan, S. H.

    1983-01-01

    Proposed process modification incorporates viscosity depressants to prevent coal from solidifying during liquefaction. Depressants reduce amount of heat needed to liquefy coal. Possible depressants are metallic soaps, such as stearate, and amides, such as stearamide and dimer acid amides.

  7. Distribution of chlorine in coal

    Energy Technology Data Exchange (ETDEWEB)

    Zhao Fenghua; Ren Deyi; Zhang Shuangquan [China Univ. of Mining and Technology, Beijing (China). Dept. of Resource and Engineering; Zhang Wang [Antaibao Opencast Mine, Pingshuo, Shanxi (China)

    1998-12-31

    The current advance of study on chlorine in coal is reviewed. The concentrations of chlorine in 45 Chinese coal samples are determined on whole coal basis using instrumental neutron activation analysis (INAA). The sequential chemical extraction method is put forward to determine the occurrence modes of chlorine in coal. The research shows that Chinese coals are not chlorine-rich ones compared with those from other countries. In coal from Pingshuo Antaibao Opencast Mine, 46.70%--91.78% of chlorine is in a water-soluble state, 5.20%--48.38% of it is organic chlorine bonded to coal molecules, and only 4.92%--18.78% is an organic one in an ion-exchange state; the proportions of organic chlorine increase with the decrease in ash of coal.

  8. Methodology of Estimation of Methane Emissions from Coal Mines in Poland

    Science.gov (United States)

    Patyńska, Renata

    2014-03-01

    Based on a literature review concerning methane emissions in Poland, it was stated in 2009 that the National Greenhouse Inventory 2007 [13] was published. It was prepared firstly to meet Poland's obligations resulting from point 3.1 Decision no. 280/2004/WE of the European Parliament and of the Council of 11 February 2004, concerning a mechanism for monitoring community greenhouse gas emissions and for implementing the Kyoto Protocol and secondly, for the United Nations Framework Convention on Climate Change (UNFCCC) and Kyoto Protocol. The National Greenhouse Inventory states that there are no detailed data concerning methane emissions in collieries in the Polish mining industry. That is why the methane emission in the methane coal mines of Górnośląskie Zagłębie Węglowe - GZW (Upper Silesian Coal Basin - USCB) in Poland was meticulously studied and evaluated. The applied methodology for estimating methane emission from the GZW coal mining system was used for the four basic sources of its emission. Methane emission during the mining and post-mining process. Such an approach resulted from the IPCC guidelines of 2006 [10]. Updating the proposed methods (IPCC2006) of estimating the methane emissions of hard coal mines (active and abandoned ones) in Poland, assumes that the methane emission factor (EF) is calculated based on methane coal mine output and actual values of absolute methane content. The result of verifying the method of estimating methane emission during the mining process for Polish coal mines is the equation of methane emission factor EF.

  9. TEKO returns to coal

    International Nuclear Information System (INIS)

    TREND

    2003-01-01

    Slovak government will not grant state long-term credit guarantee sized about 1 billion Slovak crowns, which Geoterm, a.s., Kosice company would like to get from World bank. Loan should be used as for construction of geothermal source in village Durkov near Kosice, which would be connected in Kosice thermal plant TEKO, a.s. Geothermal sources capacity after realization of planned investments should reach half of present output of plant. The nearest TEKO investments should head to changes in plant production process. Plant wants to redirect in heat and thermal energy production from existing dominant gas consumption to black coal incineration. Black coal incineration is more advantageous than natural gas exploitation in spite of ecologic loads. TEKO also will lower gas consumption for at least 30 per cent and rise up present black coal consumption almost twice

  10. Pyrolysis of coal

    Science.gov (United States)

    Babu, Suresh P.; Bair, Wilford G.

    1992-01-01

    A method for mild gasification of crushed coal in a single vertical elongated reaction vessel providing a fluidized bed reaction zone, a freeboard reaction zone, and an entrained reaction zone within the single vessel. Feed coal and gas may be fed separately to each of these reaction zones to provide different reaction temperatures and conditions in each reaction zone. The reactor and process of this invention provides for the complete utilization of a coal supply for gasification including utilization of caking and non-caking or agglomerating feeds in the same reactor. The products may be adjusted to provide significantly greater product economic value, especially with respect to desired production of char having high surface area.

  11. Analysis of hard coal quality for narrow size fraction under 20 mm

    Science.gov (United States)

    Niedoba, Tomasz; Pięta, Paulina

    2018-01-01

    The paper presents the results of an analysis of hard coal quality diversion in narrow size fraction by using taxonomic methods. Raw material samples were collected in selected mines of Upper Silesian Industrial Region and they were classified according to the Polish classification as types 31, 34.2 and 35. Then, each size fraction was characterized in terms of the following properties: density, ash content, calorific content, volatile content, total sulfur content and analytical moisture. As a result of the analysis it can be stated that the best quality in the entire range of the tested size fractions was the 34.2 coking coal type. At the same time, in terms of price parameters, high quality of raw material characterised the following size fractions: 0-6.3 mm of 31 energetic coal type and 0-3.15 mm of 35 coking coal type. The methods of grouping (Ward's method) and agglomeration (k-means method) have shown that the size fraction below 10 mm was characterized by higher quality in all the analyzed hard coal types. However, the selected taxonomic methods do not make it possible to identify individual size fraction or hard coal types based on chosen parameters.

  12. Assessment of the content of arsenic in solid by-products from coal combustion

    Directory of Open Access Journals (Sweden)

    Wierońska Faustyna

    2017-01-01

    Full Text Available The coal combustion processes constitute one of the major sources of heavy metals emission into the atmosphere. From the point of view of the reduction of the emission of heavy metals and the selection of the correct exhaust gas treatment system, it is important to monitor the amount of trace elements in the solid fuels and in the solid by-products from coal combustion. One of these highly toxic elements is arsenic. The average content of arsenic in Polish hard coals and lignites is 0 ÷ 40 mg/kg [1] and 5 ÷ 15 mg/kg [2], respectively. The world average content of arsenic in hard coals and lignites, is equal to 9.0 ± 0.8 and 7.4 ± 1.4 mg/kg [3], respectively. During coal combustion processes, a significant amount of arsenic enters the atmosphere through gases and fly ashes. The proportions in which those two forms of arsenic occur in exhaust gases depend on the conditions of combustion processes [4]. The aim of the research was to determine the content of arsenic in coal blends and by-products of their combustion (slag, fly ash, gypsum, filter cakes. The determination of the arsenic quantity was performed using the Atomic Absorption Spectrometry with the electrothermal atomization.

  13. Coal: the dinosaur wakes up

    International Nuclear Information System (INIS)

    Rousseau, Y.; Cosnard, D.

    2005-01-01

    In western countries, coal is considered as an industry of the past, but at the Earth's scale the situation is radically the opposite. Since three years, coal is the faster developing energy source, in particular thanks to China expansion and to the oil crisis which makes coal more competitive. This short paper presents the situation of coal mining in China: projects, working conditions and environmental impact. (J.S.)

  14. Sustainable development with clean coal

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-08-01

    This paper discusses the opportunities available with clean coal technologies. Applications include new power plants, retrofitting and repowering of existing power plants, steelmaking, cement making, paper manufacturing, cogeneration facilities, and district heating plants. An appendix describes the clean coal technologies. These include coal preparation (physical cleaning, low-rank upgrading, bituminous coal preparation); combustion technologies (fluidized-bed combustion and NOx control); post-combustion cleaning (particulate control, sulfur dioxide control, nitrogen oxide control); and conversion with the integrated gasification combined cycle.

  15. Direct polishing of aluminum mirrors with higher quality and accuracy.

    Science.gov (United States)

    Yin, Ziqiang; Yi, Zhang

    2015-09-10

    Diamond-turned aluminum mirrors have been widely used in modern optical systems. However, the machined surfaces have characteristic periodic tool marks, which contribute to reduced optical performance by creating effects such as scattering and distortion. This paper develops a new polishing technology to polish aluminum mirrors directly to remove tool marks and improve surface quality and surface accuracy. A Taguchi experiment was used to obtain optimal polishing conditions for reducing surface roughness, and computer-controlled optical surfacing technology was employed for form correction of aluminum mirrors.

  16. Reel-to-reel substrate tape polishing system

    Energy Technology Data Exchange (ETDEWEB)

    Selvamanickam, Venkat; Gardner, Michael T.; Judd, Raymond D.; Weloth, Martin; Qiao, Yunfei

    2005-06-21

    Disclosed is a reel-to-reel single-pass mechanical polishing system (100) suitable for polishing long lengths of metal substrate tape (124) used in the manufacture of high-temperature superconductor (HTS) coated tape, including multiple instantiations of a polishing station (114) in combination with a subsequent rinsing station (116) arranged along the axis of the metal substrate tape (124) that is translating between a payout spool (110a) and a take-up spool (110b). The metal substrate tape obtains a surface smoothness that is suitable for the subsequent deposition of a buffer layer.

  17. Quality in Air transport process of LOT Polish Airlines

    Directory of Open Access Journals (Sweden)

    Robert Rozenberg

    2015-10-01

    Full Text Available This article discusses the air transport process on scheduled long-haul flights of LOT Polish Airlines. Main focus is taken on price development of these routes. The introduction consists of a brief profile characterized LOT Polish Airlines. Next chapter summarizes the air transport process on scheduled longhaul flights. The frame of article is formed by price development statistics for scheduled long-haul flights to / from Beijing of LOT Polish Airlines and two other competing companies. Conclusion contains results of analysis and puts forward proposals to streamline of the air transport process on reviewed routes.

  18. Presentation of the verbs in Bulgarian-Polish electronic dictionary

    Directory of Open Access Journals (Sweden)

    Ludmila Dimitrova

    2014-09-01

    Full Text Available Presentation of the verbs in Bulgarian-Polish electronic dictionary This paper briefly discusses the presentation of the verbs in the first electronic Bulgarian-Polish dictionary that is currently being developed under a bilateral collaboration between IMI-BAS and ISS-PAS. Special attention is given to the digital entry classifiers that describe Bulgarian and Polish verbs. Problems related to the correspondence between natural language phenomena and their presentations are discussed. Some examples illustrate the different types of dictionary entries for verbs.

  19. Profilometric analysis of root surfaces after using various polishing agents

    Directory of Open Access Journals (Sweden)

    Anjan Jana

    2016-01-01

    Full Text Available Background: Polishing is an important step in oral prophylaxis procedure which retards further accumulation of plaque on the root surfaces. Though polishing was done with various abrasive particles with different sizes over a long period of time, it was never been highlighted to evaluate the ideal polishing material and the particle size that would produce the ideal surface smoothness (Ra 5 μm are not able to produce the surface smoothness <0.2 μm. Only, submicron sized particles are able to produce the desired smoothness.

  20. The new deal of coal

    International Nuclear Information System (INIS)

    Kalaydjian, F.; Cornot-Gandolphe, S.

    2008-01-01

    While coal appears as an inescapable resource to answer the energy needs of the 21. century, its highly CO 2 emitting combustion represents a major risk with respect to the requirements of the fight against climate change. In the first part of this book, the basic aspects of energy markets are explained and in particular the role that coal is going to play in the world's energy supplies. In the second part, the new coal usages are presented, which, combined with CO 2 capture and sequestration techniques, should allow to conciliate a massive use of coal and the respect of environmental constraints. This book is based on the works presented in February 2008 by the French institute of petroleum (IFP) about the new outlets of coal and the risks for climate change. Content: 1 - coal, energy of the 21. century: abundant and well distributed reserves; growing up world production; exponential world demand; international trade: still limited but in full expansion; 2 - Technologies for a CO 2 -free coal: CO 2 capture and sequestration technologies; towards poly-generation; production of coal-derived liquid fuels; 3 - Appendices: coals formation; coal in China: status and perspectives; coal in the USA: status and perspectives; coal in India: status and perspectives; COACH: an ambitious European project; CBM - E-CBM, status and perspectives. (J.S.)

  1. Coal terminal developments

    Energy Technology Data Exchange (ETDEWEB)

    Venter, J.

    2008-02-15

    The article reports developments at many coal terminals worldwide. These include Bulgaria's Port of Bourgas Temrinal 2A, Spain's Tarragona Port Services (TPS) terminal, New Zealand's Lyttleton Port of Christchurch (LPC), Kinder Morgan's terminals in the USA (the International Marine terminal, Cora terminal, Grand Rivers terminal and Fairless Hills terminal) and Croatia's Port of Ploce. Developments at coal terminals in France and Belgium are also summarized. Global transportation services offered by Rhenus are described. 12 photos.

  2. Study on the influence of the rotational speed of polishing disk on material removal in aspheric surface compliant polishing

    Directory of Open Access Journals (Sweden)

    Liyong Hu

    2015-03-01

    Full Text Available When a soft polishing tool is compressed on a stiff workpiece of curved surface, the contact area is a piece of the curved surface. In the process of aspheric surface polishing, the machining speed is always provided by the rotational speed of the spindle of a computer numerical control lathe. Yet, the polishing tool is usually made rotating to remove cutting scraps and broken abrasives from the contact area. The rotational speed of the polishing tool would change the distribution state of the relative speed in the whole contact area, and it would definitely change the volume of material removal in the surface of the workpiece. This article studies how the rotational speed of the polishing tool changes the distribution state of the relative speed in the whole contact area and material removal in the volume of the surface of the workpiece. The computing results show that the volume of material removal increases with the increase in both the rotational speed of polishing disk and the rotational speed of lathe spindle, but the polishing quality is totally not in this case.

  3. Coal blending preparation for non-carbonized coal briquettes

    Science.gov (United States)

    Widodo; Fatimah, D.; Estiaty, L. M.

    2018-02-01

    Referring to the national energy policy targets for the years 2025, the government has launched the use of coal briquettes as an alternative energy replacement for kerosene and firewood. Non-carbonized briquettes in the form of coal briquettes as well as bio-coal briquettes are used in many small-medium industries and households, and are rarely used by large industries. The standard quality of coal briquettes used as raw material for non-carbonized briquettes is a minimum calorific value of 4,400 kcal/kg (adb); total sulfur at a maximum of 1% (adb), and water content at <12% (adb). The formation of coal deposits depends on the origin of the coal-forming materials (plants), the environment of deposition, and the geological conditions of the surrounding area, so that the coal deposits in each region will be different as well as the amount and also the quality. Therefore, the quantity and the quality of coal in each area are different to be eligible in the making of briquettes to do blending. In addition to the coal blending, it is also necessary to select the right materials in the making of coal briquettes and bio-coal briquettes. The formulation of the right mixture of material in the making of briquettes, can be produced of good quality and environmental friendly.

  4. Bio-coal briquettes using low-grade coal

    Science.gov (United States)

    Estiaty, L. M.; Fatimah, D.; Widodo

    2018-02-01

    The technology in using briquettes for fuel has been widely used in many countries for both domestic and industrial purposes. Common types of briquette used are coal, peat, charcoal, and biomass. Several researches have been carried out in regards to the production and the use of briquettes. Recently, researches show that mixing coal and biomass will result in an environmentally friendly briquette with better combustion and physical characteristics. This type of briquette is known as bio-coal briquettes. Bio-coal briquettes are made from agriculture waste and coal, which are readily available, cheap and affordable. Researchers make these bio-coal briquettes with different aims and objectives, depending on the issues to address, e.g. utilizing agricultural waste as an alternative energy to replace fossil fuels that are depleting its reserves, adding coal to biomass in order to add calorific value to bio-coal briquette, and adding biomass to coal to improve its chemical and physical properties. In our research, biocoal briquettes are made to utilize low grade coal. The biomass we use, however, is different from the ones used in past researches because it has undergone fermentation. The benefits of using such biomass are 1. Fermentation turns the hemi cellulose into a simpler form, so that the burning activation energy decreases while the calorific value increases. 2. Enzym produced will bind to heavy metals from coal as co-factors, forming metals that are environmentally friendly.

  5. Estimation of Moisture Content in Coal in Coal Mills

    DEFF Research Database (Denmark)

    Odgaard, Peter Fogh; Mataji, Babak

    2006-01-01

    For coal-fired power plants information of the moisture content in the coal is important to determine and control the dynamical behavior of the power plants. E.g. a high moisture content in the coal can result in a decreased maximum load gradient of the plant. In this paper a method for estimating...... the moisture content of the coal is proposed based on a simple dynamic energy model of a coal mill, which pulverizes and dries the coal before it is burned in the boiler. An optimal unknown input observer is designed to estimate the moisture content based on an energy balance model. The designed moisture...... estimator is verified on a couple of sets of measurement data, from which it is concluded that the designed estimator estimates the real coal moisture content....

  6. Estimation of Moisture Content in Coal in Coal Mills

    DEFF Research Database (Denmark)

    Odgaard, Peter Fogh; Mataji, B.

    For coal-fired power plants information of the moisture content in the coal is important to determine and control the dynamical behavior of the power plants. E.g. a high moisture content in the coal can result in a decreased maximum load gradient of the plant. In this paper a method for estimating...... the moisture content of the coal is proposed based on a simple dynamic energy model of a coal mill, which pulverizes and dries the coal before it is burned in the boiler. An optimal unknown input observer is designed to estimate the moisture content based on an energy balance model. The designed moisture...... estimator is verified on a couple sets of measurement data, from which it is concluded that the designed estimator estimates the real coal moisture content....

  7. Polish origins of the Faculty of Mathematical and Natural Sciences of the University of Fribourg and the Polish contribution to the Fribourg industrial revolution (in Polish

    Directory of Open Access Journals (Sweden)

    Wojciech KOCUREK

    2015-12-01

    Full Text Available The article is dedicated to high-tech companies founded by Poles at the end of the 19th century in the rural canton of Fribourg in Switzerland. The text is divided into two parts. In the first part, the author attempts to present the economic, social and political reality of Fribourg in a period of intense industrialization in the world and the formation of the liberal free market system. In this rapidly changing reality, the new Catholic-conservative authorities of the canton tried to lead to establishing of a comprehensive, but also different system of a “Christian republic”, whose aim was to achieve social justice consistent with the teachings of the Gospel. In order to complete the project, the cantonal government did not shy away from using the possibilities and measures offered by the contemporary world. Decision-makers, led by Georges Python, needed support from the society, who was aware of the changes. Due to this fact, it became necessary to establish a university capable of shaping new attitudes and views. However, the costs significantly exceeded the financial capabilities of the agricultural and relatively poor canton of Fribourg. In these less favourable circumstances, a conscious policy of industrialization was the way out of the deadlock. Newly created industrial institutions were to contribute to an increase of cash inflows to the canton and thus allow for the financing of the university, which would also become an intellectual foundation for the emerging industry. The activity of Polish scientists, which is the subject of the second part of the article, matched this philosophy perfectly. The Poles invited to cooperate with Python, i.e. Józef Wierusz-Kowalski, Ignacy Mościcki and Jan Modzelewski, created the foundations of the Faculty of Mathematical and Natural Sciences at the University of Fribourg. As members of the faculty, in addition to teaching, they conducted research into, among other things, nitric acid

  8. Surface Properties of Photo-Oxidized Bituminous Coals: Final report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-09-01

    Natural weathering has a detrimental effect on the hydrophobic nature of coal, which in turn can influence clean-coal recovery during flotation. Few techniques are available that can establish the quality of coal surfaces and that have a short analysis time to provide input for process control. Luminescence emissions which can be quantified with an optical microscope and photometer system, are measurably influenced by degree of weathering as well as by mild storage deterioration. In addition, it has been shown that when vitrinite is irradiated with a relatively high intensity flux of violet- or ultraviolet- light in the presence of air, photo-oxidation of the surface occurs. The combination of measuring the change in luminescence emission intensity with degree of surface oxidation provided the impetus for the current investigation. The principal aim of this research was to determine whether clear correlations could be established among surface oxygen functionality, hydrophobicity induced by photo-oxidation, and measurements of luminescence intensity and alteration. If successful, the project would result in quantitative luminescence techniques based on optical microscopy that would provide a measure of the changes in surface properties as a function of oxidation and relate them to coal cleanability. Two analytical techniques were designed to achieve these goals. Polished surfaces of vitrain bands or a narrow size fraction of powdered vitrain concentrates were photo-oxidized using violet or ultraviolet light fluxes and then changes in surface properties and chemistry were measured using a variety of near-surface analytical techniques. Results from this investigation demonstrate that quantitative luminescence intensity measurements can be performed on fracture surfaces of bituminous rank coals (vitrains) and that the data obtained do reveal significant variations depending upon the level of surface oxidation. Photo-oxidation induced by violet or ultraviolet light

  9. Coal: Demand up - prices down

    International Nuclear Information System (INIS)

    Prior, M.

    1993-01-01

    1992 was a year in which demand for traded coal moved upward in the steam-coal sector though it remained stagnant for metallurgical coal. Both Australia and South Africa exported record volumes and new extrants to the market came from Indonesia and Venezuela. Despite this upward movement in demand, coal prices slipped relentlessly downward to the point where at the year-end, significant mine closures were occurring throughout the world. The main question for 1993 is how long can the producers go on hurting before the prices start to move up? The overall world demand for steam coal is discussed

  10. Effect of Polishing Systems on Surface Roughness and Topography of Monolithic Zirconia.

    Science.gov (United States)

    Goo, C L; Yap, Auj; Tan, Kbc; Fawzy, A S

    2016-01-01

    This study evaluated the effect of different chairside polishing systems on the surface roughness and topography of monolithic zirconia. Thirty-five monolithic zirconia specimens (Lava PLUS, 3M ESPE) were fabricated and divided into five groups of seven and polished with the following: Group 1 (WZ)-Dura white stone followed by Shofu zirconia polishing kit; Group 2 (SZ)-Shofu zirconia polishing kit; Group 3 (CE)-Ceramiste porcelain polishers; Group 4 (CM)-Ceramaster porcelain polishers; and Group 5 (KZ)-Komet ZR zirconia polishers. All specimens were ground with a fine-grit diamond bur prior to polishing procedures to simulate clinical finishing. Baseline and post-polishing profilometric readings were recorded and delta Ra values (difference in mean surface roughness before and after polishing) were computed and analyzed using one-way analysis of variance and Scheffe post hoc test (pzirconia.

  11. Wear surface studies on coal water slurry nozzles in industrial boilers

    Energy Technology Data Exchange (ETDEWEB)

    Ding Zeliang [Hunan Engineering Technology Key Laboratory of Inorganic and Nonmetal Materials, Hunan University of Technology, Zhuzhou 412008, Hunan Province (China)]. E-mail: dingzl@263.net; Deng Jianxin [Department of Mechanical Engineering, Shandong University, Jinan 250061, Shandong Province (China)]. E-mail: jxdeng@sdu.edu.cn; Li Jianfeng [Department of Mechanical Engineering, Shandong University, Jinan 250061, Shandong Province (China)]. E-mail: ljf@sdu.edu.cn

    2007-07-01

    In this study, Al{sub 2}O{sub 3}/(W,Ti)C ceramic, WC/Co cemented carbide, and 1Cr18Ni9Ti stainless steel were produced to be used as nozzle materials in coal water slurry (CWS) industry boilers. Coal water slurry burning tests with these nozzles were carried out. The wear surface features of the nozzles made from these materials were examined. The results showed that the wear mechanisms of nozzles varied from entry to exit. The material removal of Al{sub 2}O{sub 3}/(W,Ti)C ceramic nozzle in CWS atomizing and burning is attributed to a mixed mode damage by brittle fracture, polishing, thermal cracking and chipping. The nozzle entry section appears to be entirely brittle in nature with evidence of large scale-chipping. The centre bore area showed a polishing effect with a very smooth surface. While the exit section exhibits cracking owing to the large thermal shock. Examination of the eroded bore surface of the WC/Co cemented carbide nozzles demonstrated that the wear occurred through preferential removal of the metal binder (Co) followed by pluck-out of the exposed WC grains at the entry zone, while the center and the exit zone showed polishing action. The primary wear mechanisms of 1Cr18Ni9Ti stainless steel nozzle exhibited plastic deformation at the entry zone, and plowing and micro-cutting at the other zones by the eroded particles.

  12. Polish electoral geography and its methods

    Directory of Open Access Journals (Sweden)

    Zbigniew Rykiel

    2011-01-01

    Full Text Available Differences in the understanding of electoral geography between social sciences are discussed in the article. Main fields and spatial scales of Polish electoral geography are identified. Main methods of multidimensional statistics are discussed. A necessity of a proper choice, based on theories of voting behaviour, of explaning variables to statistical models are emphasised. Regression analysis indicates only a formal usefulness in electoral geography, for quantitative relationships between variables in the model can be evidenced, which may be meaningless not only essentially, but even statistically. The application of canonical analysis in electoral geography brought a methodological turning-point to the statistical approach. This method allowed to combine: (1 the foundation of the selection of input variables on theories of voting behaviour; (2 the analysis of dependence of the electoral results on socio-economic characteristics of areas; (3 an identification of electoral options; (4 a quantification of the role of the historical heritage in the contemporary voting behaviour; and (5 the analysis of the stability of the electoral space. A well grounded opinion was weakened about the general competitiveness of right- and left-wing parties in Poland’s political space. Parties with similar rather than different programmes compete in given areas. It was indicated that elections have only formal influence on the structure of Parliament while the electoral system is decisive. Electoral, including territorial, manipulations also play their part. The empirical analysis indicated that Poland’s political space is polarised between the right-wing-oriented areas of the south-eastern half of the country and the left-wing-oriented areas of the north-western half. The political competition between the left and the right operates merely on the national scale, while it is not reflected territorially.The quantification of the influence of the nineteenth

  13. World coking coal markets

    International Nuclear Information System (INIS)

    McCloskey, G.

    2010-01-01

    This article discussed conditions in world coking coal markets. There is increased demand from Asia for metallurgical coal imports. World iron production was up 22 percent in first 7 months of 2010. Supply is up in Australia, the United States, Canada, New Zealand, Russia, and Mongolia, but the unexpected surge in supply caused prices to drop following a robust start to the year. Coking coal exports are up for the United States and Australia, but a delay in expanded production is expected until 2014. There is increased demand from Brazil, India, Taiwan, South Korea, and Japan as well as new plants in Thailand, Indonesia, and Brazil. Unexpectedly, Australia is backing out of the Chinese market but increasing exports to Japan and South Korea. India is seeing flat performance in iron production and imports, and the United States has surged back into Asia. A considerable increase is expected in the seaborne import requirement by 2020. Prices are expected to fall and then rise. This presentation also discussed whether coking coal index pricing is impossible or inevitable. 3 tabs., 5 figs.

  14. Kinetics of coal pyrolysis

    Energy Technology Data Exchange (ETDEWEB)

    Seery, D.J.; Freihaut, J.D.; Proscia, W.M. (United Technologies Research Center, East Hartford, CT (USA)); Howard, J.B.; Peters, W.; Hsu, J.; Hajaligol, M.; Sarofim, A. (Massachusetts Inst. of Tech., Cambridge, MA (USA)); Jenkins, R.; Mallin, J.; Espindola-Merin, B. (Pennsylvania State Univ., University Park, PA (USA)); Essenhigh, R.; Misra, M.K. (Ohio State Univ., Columbus, OH (USA))

    1989-07-01

    This report contains results of a coordinated, multi-laboratory investigation of coal devolatilization. Data is reported pertaining to the devolatilization for bituminous coals over three orders of magnitude in apparent heating rate (100 to 100,000 + {degree}C/sec), over two orders of magnitude in particle size (20 to 700 microns), final particle temperatures from 400 to 1600{degree}C, heat transfer modes ranging from convection to radiative, ambient pressure ranging from near vacuum to one atmosphere pressure. The heat transfer characteristics of the reactors are reported in detail. It is assumed the experimental results are to form the basis of a devolatilization data base. Empirical rate expressions are developed for each phase of devolatilization which, when coupled to an awareness of the heat transfer rate potential of a particular devolatilization reactor, indicate the kinetics emphasized by a particular system reactor plus coal sample. The analysis indicates the particular phase of devolatilization that will be emphasized by a particular reactor type and, thereby, the kinetic expressions appropriate to that devolatilization system. Engineering rate expressions are developed from the empirical rate expressions in the context of a fundamental understanding of coal devolatilization developed in the course of the investigation. 164 refs., 223 figs., 44 tabs.

  15. Methanol from coal

    Science.gov (United States)

    Miller, D. R.

    1978-01-01

    Economic feasibility of methanol or methyl fuel produced from coal using existing technology is discussed. Other factors considered include environmental, safety, toxicity, transportation, so storage, ease of burning, and retrofitting of present boilers. Demonstrations of its uses as a boiler fuel and as a turbine fuel are cited.

  16. Coal sampling device

    Energy Technology Data Exchange (ETDEWEB)

    Huck, W.R.

    1985-10-22

    This invention pertains to a device for taking samples of finely crushed particulate matter, such as coal from a flowing feed stream on a preset selection schedule, using a rotating drum which has one slot in its periphery and a receptable moveable into and out of the center area of the drum in alignment with said slot.

  17. Underground Coal Mining

    Science.gov (United States)

    Hill, G. M.

    1980-01-01

    Computer program models coal-mining production, equipment failure and equipment repair. Underground mine is represented as collection of work stations requiring service by production and repair crews alternately. Model projects equipment availability and productivity, and indicates proper balance of labor and equipment. Program is in FORTRAN IV for batch execution; it has been implemented on UNIVAC 1108.

  18. Proximate Analysis of Coal

    Science.gov (United States)

    Donahue, Craig J.; Rais, Elizabeth A.

    2009-01-01

    This lab experiment illustrates the use of thermogravimetric analysis (TGA) to perform proximate analysis on a series of coal samples of different rank. Peat and coke are also examined. A total of four exercises are described. These are dry exercises as students interpret previously recorded scans. The weight percent moisture, volatile matter,…

  19. Current status of U.S. coal utilization and non-fuel uses of fossil fuels

    International Nuclear Information System (INIS)

    Song, C.S.; Schobert, H.; Scaroni, A.W.

    1997-01-01

    An understanding of the current situation is important for projecting the future direction of coal utilization. The world's annual consumption of coal in 1995 was 5104.01 million short tons (MST, 1 short ton = 0.907 metric ton). Coal plays a very important role in the US energy supply; US coal production in 1995 totaled 1033 MST, including 611.1 MST of bituminous coal, 328.4 MST of subbituminous coal, 86.1 MST of lignite, and 4.1 MST of anthracite. US coal consumption totaled 940.6 MST, with 88.1% in electric utilities, 3.5% in coke plants, 7.8% for other industrial uses, and only 0.6% in the residential and commercial sectors. The amount of fossil resources used for non-fuel purposes accounted for 8.4% of the total annual consumption in 1995. Non-fuel uses of fossil fuels particularly coal may become more important in the future. The demonstrated coal reserves in the world are large enough for consumption for over 220 years at the 1995 level, while proven oil reserves are only about 40 times the world's 1995 consumption level. Coal has several positive attributes when considered as a feedstock for aromatic chemicals, specialty chemicals, and carbon-based materials. Existing nonfuel uses of coals include (1) high temperature carbonization of bituminous and subbituminous coals to make metallurgical coke; (2) gasification of coal to make synthesis gases and other chemicals; (3) use of coal in manufacturing other materials such as activated carbons, carbon molecular sieves (CMS) and production of phosphorus (phosphoric acid); (4) the use of coal tars from carbonization and gasification for making aromatic and phenolic chemicals; (5) the use of coal tar pitch for making carbon fibers and activated carbon fibers; and (6) other non-fuel products derived from coal including combustion by-products. Coal may become more important both as an energy source and as the source of chemical feedstocks in the 21st century

  20. Polish Defense Policy in the Context of National Security Strategy

    Science.gov (United States)

    2006-06-01

    Antoni Podolski, Polska Strategia Bezpieczenstwa jako Praktyczna Implementacja Europejskiej Strategii Bezpeczenstwa –miedzy teoria a praktyka (Warszawa...Implementacja Europejskiej Strategii Bezpeczenstwa –miedzy teoria a praktyka (Warszawa: Center for International Relations, 2005), 13. Polish Ministry

  1. Super Polishing of Aluminum 6061-T6 Mirrors, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — An innovative 2D super-polishing process for Aluminum 6061-T6 planar mirrors which removes diamond point turning (DPT) grooves and attains rms surface finishes below...

  2. The resettlement of Polish refugees after the second world war

    Directory of Open Access Journals (Sweden)

    Agata Blaszczyk

    2017-02-01

    Full Text Available The passing of the Polish Resettlement Act and the creation of the different agencies related to it undoubtedly represented an unprecedented response to the challenge of mass migration in the UK.

  3. Production of rare earth polishing powders in Russia

    International Nuclear Information System (INIS)

    Kosynkin, V.D.; Ivanov, E.N.; Kotrekhov, V.A.; Shtutza, M.G.; Grabko, A.I.

    1998-01-01

    Full text: Russia is a potent producer of polishing powders made of rare earth material presented as an extensive and well developed base. Considering the reserves, the facilities predisposition and the polishing agent (cerium dioxide) content the chief mineral source is loparite, apatite and monazite. The production of rare earth polishing powders is based on specially developed continuous technological processes, corrosion-proof equipment, ensuring a high and stable production quality. A special attention is paid to the radiation safety of the powders. The initial material for the rare earth polishing powders based on loparite is the fusion cake of rare earth chlorides obtained at that mineral chlorination. The technology of the polishing powder production from the REE fusion cake includes the following stages: dissolution of the REE fusion cake chlorides; - thorough cleaning of the REE fusion cake chlorides from radioactive and non-rare-earth impurities; chemical precipitation of REE carbonates, obtaining middlings with proper material and granulometric composition, thermal treatment of precipitated carbonates followed with the operations of drying and roasting; classification of roasted oxides, obtaining end products - polishing powders. The production of fluorine-containing powders includes the stage of their fluorination after the stage of carbonate precipitation. The stabilizing doping can be introduced both into the middlings during one of the technological process of powders manufacturing and into the end product. Rare earth polishing powders are manufactured in Russia by the Share Holding Company 'Chepetz Mechanical Plant' (ChMP Co.), the city of Glasov. The plant produces a number of polishing materials, such as; polishing powder Optinol, containing at least 50% by mass of cerium dioxide, used in the mass production of optical and other articles; polishing powder Optinol-10 with doping to improve the sedimentary and aggregate stability of the solid phase

  4. British and American English for Polish University Students

    Science.gov (United States)

    Marton, Waldemar; Preston, Dennis R.

    1975-01-01

    This article attempts to assess the validity of dividing Polish students of English into British and American groups. The tests of the various hypotheses regarding linguistic and non-linguistic results of such divisions are described. (AM)

  5. Polish Defense Policy in the Context of National Security Strategy

    National Research Council Canada - National Science Library

    Bieniek, Piotr S

    2006-01-01

    ...) and the North Atlantic Treaty Organization (NATO). Polish security policy and strategy is shaped by its geographical location, which places Poland in NATO's main strategic area opposite the Russian Federation and Belarus...

  6. Mercury emissions from coal combustion in Silesia, analysis using geostatistics

    Science.gov (United States)

    Zasina, Damian; Zawadzki, Jaroslaw

    2015-04-01

    Data provided by the UNEP's report on mercury [1] shows that solid fuel combustion in significant source of mercury emission to air. Silesia, located in southwestern Poland, is notably affected by mercury emission due to being one of the most industrialized Polish regions: the place of coal mining, production of metals, stone mining, mineral quarrying and chemical industry. Moreover, Silesia is the region with high population density. People are exposed to severe risk of mercury emitted from both: industrial and domestic sources (i.e. small household furnaces). Small sources have significant contribution to total emission of mercury. Official and statistical analysis, including prepared for international purposes [2] did not provide data about spatial distribution of the mercury emitted to air, however number of analysis on Polish public power and energy sector had been prepared so far [3; 4]. The distribution of locations exposed for mercury emission from small domestic sources is interesting matter merging information from various sources: statistical, economical and environmental. This paper presents geostatistical approach to distibution of mercury emission from coal combustion. Analysed data organized in 2 independent levels: individual, bottom-up approach derived from national emission reporting system [5; 6] and top down - regional data calculated basing on official statistics [7]. Analysis, that will be presented, will include comparison of spatial distributions of mercury emission using data derived from sources mentioned above. Investigation will include three voivodeships of Poland: Lower Silesian, Opole (voivodeship) and Silesian using selected geostatistical methodologies including ordinary kriging [8]. References [1] UNEP. Global Mercury Assessment 2013: Sources, Emissions, Releases and Environmental Transport. UNEP Chemicals Branch, Geneva, Switzerland, 2013. [2] NCEM. Poland's Informative Inventory Report 2014. NCEM at the IEP-NRI, 2014. http

  7. EVALUATION OF BIOMASS AND COAL CO-GASIFICATION OF BRAZILIAN FEEDSTOCK USING A CHEMICAL EQUILIBRIUM MODEL

    Directory of Open Access Journals (Sweden)

    R. Rodrigues

    Full Text Available Abstract Coal and biomass are energy sources with great potential for use in Brazil. Coal-biomass co-gasification enables the combination of the positive characteristics of each fuel, besides leading to a cleaner use of coal. The present study evaluates the potential of co-gasification of binary coal-biomass blends using sources widely available in Brazil. This analysis employs computational simulations using a reliable thermodynamic equilibrium model. Favorable operational conditions at high temperatures are determined in order to obtain gaseous products suitable for energy cogeneration and chemical synthesis. This study shows that blends with biomass ratios of 5% and equivalence ratios ≤ 0.3 lead to high cold gas efficiencies. Suitable gaseous products for chemical synthesis were identified at biomass ratios ≤ 35% and moisture contents ≥ 40%. Formation of undesirable nitrogen and sulfur compounds was also analyzed.

  8. Laser polishing of 3D printed mesoscale components

    Energy Technology Data Exchange (ETDEWEB)

    Bhaduri, Debajyoti, E-mail: debajyoti.bhaduri@gmail.com [Department of Mechanical Engineering, School of Engineering, University of Birmingham, Edgbaston, Birmingham, B15 2TT (United Kingdom); Penchev, Pavel; Batal, Afif; Dimov, Stefan; Soo, Sein Leung [Department of Mechanical Engineering, School of Engineering, University of Birmingham, Edgbaston, Birmingham, B15 2TT (United Kingdom); Sten, Stella; Harrysson, Urban [Digital Metal, Höganäs AB, 263 83 Höganäs (Sweden); Zhang, Zhenxue; Dong, Hanshan [School of Metallurgy and Materials, University of Birmingham, Edgbaston, Birmingham, B15 2TT (United Kingdom)

    2017-05-31

    Highlights: • Process optimisation for laser polishing novel 3D printed SS316L parts. • Evaluating the effects of key polishing parameters on SS316L surface roughness. • Detailed spectroscopic analysis of oxide layer formation due to laser polishing. • Comparative surface integrity analysis of SS parts polished in air and argon. • A maximum reduction in roughness of over 94% achieved at optimised polishing settings. - Abstract: Laser polishing of various engineered materials such as glass, silica, steel, nickel and titanium alloys, has attracted considerable interest in the last 20 years due to its superior flexibility, operating speed and capability for localised surface treatment compared to conventional mechanical based methods. The paper initially reports results from process optimisation experiments aimed at investigating the influence of laser fluence and pulse overlap parameters on resulting workpiece surface roughness following laser polishing of planar 3D printed stainless steel (SS316L) specimens. A maximum reduction in roughness of over 94% (from ∼3.8 to ∼0.2 μm S{sub a}) was achieved at the optimised settings (fluence of 9 J/cm{sup 2} and overlap factors of 95% and 88–91% along beam scanning and step-over directions respectively). Subsequent analysis using both X-ray photoelectron spectroscopy (XPS) and glow discharge optical emission spectroscopy (GDOES) confirmed the presence of surface oxide layers (predominantly consisting of Fe and Cr phases) up to a depth of ∼0.5 μm when laser polishing was performed under normal atmospheric conditions. Conversely, formation of oxide layers was negligible when operating in an inert argon gas environment. The microhardness of the polished specimens was primarily influenced by the input thermal energy, with greater sub-surface hardness (up to ∼60%) recorded in the samples processed with higher energy density. Additionally, all of the polished surfaces were free of the scratch marks, pits, holes

  9. China's coal export and inspection

    International Nuclear Information System (INIS)

    Xiaodong Li

    1993-01-01

    With the development of world's business and trade, coal has become a large part of the import and export goods in the international market. The total amount of coal trade has risen a lot. China is rich in coal resources. According to the estimate made by some experts, the reserve which has been explored recently could be exploited hundreds of years. China's output of raw coal has risen a lot during the past forty years. China coal industry has developed rapidly since the 1980s. It is possible for China to become a big coal export country since it has rich resources and increasing output. The paper suggests four steps which must be taken to expand coal exports in China: improve the level of management and administration of coal mines so as to raise the economic benefit; the follow-up production capacity of the present mines must be enhanced rapidly; step up construction of new large-scale mines; and China's coal washing capacity must be improved speedily since the low capacity has seriously influenced the improvement of coal quality. The paper describes the inspection bureaus and companies that have developed to perform inspection of exports in order to guarantee the quality of export coal

  10. National Coal Quality Inventory (NACQI)

    Energy Technology Data Exchange (ETDEWEB)

    Robert Finkelman

    2005-09-30

    The U.S. Geological Survey (USGS) conducted the National Coal Quality Inventory (NaCQI) between 1999 and 2005 to address a need for quality information on coals that will be mined during the next 20-30 years. Collaboration between the USGS, State geological surveys, universities, coal burning utilities, and the coal mining industry plus funding support from the Electric Power Research Institute (EPRI) and the U.S. Department of Energy (DOE) permitted collection and submittal of coal samples for analysis. The chemical data (proximate and ultimate analyses; major, minor and trace element concentrations) for 729 samples of raw or prepared coal, coal associated shale, and coal combustion products (fly ash, hopper ash, bottom ash and gypsum) from nine coal producing States are included. In addition, the project identified a new coal reference analytical standard, to be designated CWE-1 (West Elk Mine, Gunnison County, Colorado) that is a high-volatile-B or high-volatile-A bituminous coal with low contents of ash yield and sulfur, and very low, but detectable contents of chlorine, mercury and other trace elements.

  11. The shell coal gasification process

    Energy Technology Data Exchange (ETDEWEB)

    Koenders, L.O.M.; Zuideveld, P.O. [Shell Internationale Petroleum Maatschappij B.V., The Hague (Netherlands)

    1995-12-01

    Future Integrated Coal Gasification Combined Cycle (ICGCC) power plants will have superior environmental performance and efficiency. The Shell Coal Gasification Process (SCGP) is a clean coal technology, which can convert a wide range of coals into clean syngas for high efficiency electricity generation in an ICGCC plant. SCGP flexibility has been demonstrated for high-rank bituminous coals to low rank lignites and petroleum coke, and the process is well suited for combined cycle power generation, resulting in efficiencies of 42 to 46% (LHV), depending on choice of coal and gas turbine efficiency. In the Netherlands, a 250 MWe coal gasification combined cycle plant based on Shell technology has been built by Demkolec, a development partnership of the Dutch Electricity Generating Board (N.V. Sep). The construction of the unit was completed end 1993 and is now followed by start-up and a 3 year demonstration period, after that the plant will be part of the Dutch electricity generating system.

  12. Gasification Studies Task 4 Topical Report, Utah Clean Coal Program

    Energy Technology Data Exchange (ETDEWEB)

    Whitty, Kevin [Univ. of Utah, Salt Lake City, UT (United States); Fletcher, Thomas [Univ. of Utah, Salt Lake City, UT (United States); Pugmire, Ronald [Univ. of Utah, Salt Lake City, UT (United States); Smith, Philip [Univ. of Utah, Salt Lake City, UT (United States); Sutherland, James [Univ. of Utah, Salt Lake City, UT (United States); Thornock, Jeremy [Univ. of Utah, Salt Lake City, UT (United States); Hunsacker, Isaac [Univ. of Utah, Salt Lake City, UT (United States); Li, Suhui [Univ. of Utah, Salt Lake City, UT (United States); Kelly, Kerry [Univ. of Utah, Salt Lake City, UT (United States); Puntai, Naveen [Univ. of Utah, Salt Lake City, UT (United States); Reid, Charles [Univ. of Utah, Salt Lake City, UT (United States); Schurtz, Randy [Univ. of Utah, Salt Lake City, UT (United States)

    2011-10-01

    A key objective of the Task 4 activities has been to develop simulation tools to support development, troubleshooting and optimization of pressurized entrained-flow coal gasifiers. The overall gasifier models (Subtask 4.1) combine submodels for fluid flow (Subtask 4.2) and heat transfer (Subtask 4.3) with fundamental understanding of the chemical (Subtask 4.4) and physical (Subtask 4.5) processes that take place as coal particles are converted to synthesis gas and slag. However, it is important to be able to compare predictions from the models against data obtained from actual operating coal gasifiers, and Subtask 4.6 aims to provide an accessible, non-proprietary system, which can be operated over a wide range of conditions to provide well-characterized data for model validation.

  13. Cells on fibers to degrade PAH and upgrade coal

    International Nuclear Information System (INIS)

    Clyde, R.

    1997-01-01

    There are over 2000 sites contaminated with PAH's from coal burning plants. White rot fungus degrades phenanthrene and anthracene, but the fungus needs air to grow. When grown on old cardboard boxes and buried, air is entrapped in the corrugations for growth of the fungus. When holes are put in the valleys of the corrugations and rotated in a half full reactor, drops are formed. Mass transfer to drops is much faster than to a flat surface, as described in Patent 5,256,570, so the fungus grows faster. Low rank coal can be upgraded to more valuable products with the fungus, say some Australians, but the problem is supplying oxygen. Celite can be entrapped in the fibers to ferment coal derived synthesis gas. The paper describes these processes

  14. Borel hierarchies in infinite products of Polish spaces

    Indian Academy of Sciences (India)

    with two product topologies: (i) the product of copies of the Polish topology on X, so that H is again a Polish space and (ii) the product of copies of the discrete topology on X. Define now the Borel hierarchy in the larger topology on H. To do so, we need some notation. An element of H will be denoted by h = (x1,x2,...,xn,.

  15. Evaluation of the COMSOL software electro-polishing of samples

    International Nuclear Information System (INIS)

    Bruchon, M.

    2007-01-01

    The niobium electro-polishing is efficient if a viscous layer exists at the surface. In order to define parameters of samples electro-polishing, opened with difficulty to the experiments, the simulation is essential. This report presents works realized with the COMSOL software. The Nernst Planck equations have been associated to the Navier Stockes ones for an incompressible fluid. The study of the potential behaviour on the viscous layer and the mobility value have been detailed. (A.L.B.)

  16. Borel hierarchies in infinite products of Polish spaces

    Indian Academy of Sciences (India)

    E-mail: rana@isical.ac.in; maitra@stat.umn.edu. MS received 22 August 2005; revised 28 August 2006. Abstract. Let H be a product of countably infinite number of copies of an uncountable. Polish space X. Let ξ ( ξ ) be the class of Borel sets of additive class ξ for the product of copies of the discrete topology on X (the Polish ...

  17. Stem subsidence of polished and rough double-taper stems

    Science.gov (United States)

    Yamada, Kengo; Hirosaki, Kenichi; Takano, Masahiro; Matsumoto, Tadami

    2009-01-01

    Background and purpose Many clinical reports have indicated that polished hip stems show better clinical results than rough stems of the same geometry. It is still unknown, however, what the mechanical effects are of different surface finishes on the cement at the cement-bone interface. We compared mechanical effects in an in vitro cemented hip arthroplasty model. Methods Two sizes of double-taper polished stems and matt-processed polished stems (rough stems) were fixed into composite femurs. A 1-Hz dynamic load was applied to the stems for 1 million cycles. An 8-h no-load period was set after every 16 h of load. Stem subsidence within the cement, and compressive force and horizontal cement creep at the cement-bone interface, were measured. Results Compared to rough stems, stem subsidence, compressive force and cement creep for polished stems were a maximum of 4, 12, and 7-fold greater, respectively. There was a strong positive correlation between stem subsidence and compressive force for polished stems. In contrast, a strong negative correlation was found between stem subsidence and compressive force for rough stems. There was also a statistically significant relationship between compressive force on the cement and cement creep for the polished stems, but no significant relationship was found for rough stems. Interpretation This is the first evidence that different surface finishes of stems can have different mechanical effects on the cement at the cement-bone interface. Stem subsidence in polished stems resulted in compressive force on the cement and cement creep. The mechanical effects that polished taper stems impart on cement at the cement-bone interface probably contribute to their good long-term fixation and excellent clinical outcome. PMID:19421909

  18. Lexical exponents of hypothetical modality in Polish and Lithuanian

    OpenAIRE

    Roman Roszko

    2015-01-01

    Lexical exponents of hypothetical modality in Polish and Lithuanian The article focuses on the lexical exponents of hypothetical modality in Polish and Lithuanian. The purpose for comparing and contrasting the lexical exponents of hypothetical modality is not only to identify all the lexemes in both languages but also find the answer to the following question: whether the morphological exponents of hypothetical modality (so-called modus relativus) familiar to the Lithuanian language have/...

  19. Reusing Ceramic Tile Polishing Waste In Paving Block Manufacturing

    OpenAIRE

    Giordano Penteado; Carmenlucia Santos; de Carvalho; Eduardo Viviani; Cecche Lintz; Rosa Cristina

    2016-01-01

    Ceramic companies worldwide produce large amounts of polishing tile waste, which are piled up in the open air or disposed of in landfills. These wastes have such characteristics that make them potential substitutes for cement and sand in the manufacturing of concrete products. This paper investigates the use of ceramic tile polishing waste as a partial substitute for cement and sand in the manufacturer of concrete paving blocks. A concrete mix design was defined and then the sand was replaced...

  20. Hydrothermal pretreatment of coal

    Energy Technology Data Exchange (ETDEWEB)

    Ross, D.S.

    1989-12-21

    We have examined changes in Argonne Premium samples of Wyodak coal following 30 min treatment in liquid water at autogenous pressures at 150{degrees}, 250{degrees}, and 350{degrees}C. In most runs the coal was initially dried at 60{degrees}C/1 torr/20 hr. The changes were monitored by pyrolysis field ionization mass spectrometry (py-FIMS) operating at 2.5{degrees}C/min from ambient to 500{degrees}C. We recorded the volatility patterns of the coal tars evolved over that temperature range, and in all cases the tar yields were 25%--30% of the starting coal on mass basis. There was essentially no change after the 150{degrees}C treatment. Small increases in volatility were seen following the 250{degrees}C treatment, but major effects were seen in the 350{degrees} work. The tar quantity remained unchanged; however, the volatility increased so the temperature of half volatility for the as-received coal of 400{degrees}C was reduced to 340{degrees}C. Control runs with no water showed some thermal effect, but the net effect from the presence of liquid water was clearly evident. The composition was unchanged after the 150{degrees} and 250{degrees}C treatments, but the 350{degrees} treatment brought about a 30% loss of oxygen. The change corresponded to loss of the elements of water, although loss of OH'' seemed to fit the analysis data somewhat better. The water loss takes place both in the presence and in the absence of added water, but it is noteworthy that the loss in the hydrothermal runs occurs at p(H{sub 2}O) = 160 atm. We conclude that the process must involve the dehydration solely of chemically bound elements of water, the dehydration of catechol is a specific, likely candidate.

  1. Coal resources availability in Botswana

    International Nuclear Information System (INIS)

    Modisi, M.P.

    1990-01-01

    This paper reports that Southern Africa, and Botswana in particular, is well-endowed with relatively large reserves of coal. The existence of coal in Botswana has been known since the end of the last century. Exploration activities by the Geological Survey and the private sector led to the discovery of major deposits and by the late 1960s reserves capable of supporting a mine at Morupule for the domestic market has been confirmed. The oil crises of 1973-74 and 1978-79 stimulated increased interest in coal exploration the world over and Botswana attracted several private sector companies looking for coal that could be traded on the international market. As a result vast resources and reserves of low to medium quality bituminous coal, suitable for the export market, were proved. Resources amounting to 21,680 million tonnes of in situ coal had been revealed by 1987. Reserves of possible economic exploitation are estimated at 10,180 million tonnes in two coal field areas, namely the Morupule Coal Field and the Mmamabula Coal Field. Since the collapse of oil prices and consequently coal prices in the mid-1980s, enthusiasm for coal exploration has plummeted and relatively little prospecting has taken place. The coal occurs within the Upper Carboniferous to Jurassic Karoo Supergroup which underlies some 60 percent of the country's land surface. The western part of the country is mantled by the Kalahari beds, a top layer of unconsolidated sands masking bedrock geology. Although coal seams have been intersected in boreholes in this western area, most exploration activity has taken place in the eastern part of the country where the Morupule and Mmamabula coal fields are located. It is in the east that most of the population is concentrated and infrastructure has been developed

  2. Buckets of money for coal

    International Nuclear Information System (INIS)

    Anon

    2001-01-01

    The revival of coal prices is providing record profits for Australian coal producers. As the world's largest coal exporter, any move in coal prices has significant ramifications for the Australian economy. The coal boom of the mid-1980s resulted in a massive increase in mine capacity and subsequently excess supply. This resulted in the decade between 1990 and 2000 seeing benchmark prices for coking coal in Japan plummeting to $US 39 a tonne (down from around the $US 52 mark) and a price of $US 28 for a tonne of steaming coal. Asia's financial problems, late in the decade coupled with a rapid fall in Asian steel making, also added to our coal export woes. As a result for most of the 1990s, Australia's coal sector delivered inadequate returns, was seen as over-capitalised and suffered from a profound investor indifference. But the sector is now seeing a definite turnaround in fortunes. Prices for thermal coal are on the rise and the benchmark coking coal prices to Asia have also jumped. Market analysts reported the price for contract deliveries of thermal coal in April this year were $US 34.50 ($AUD 69.35) up by $US 5.75 from the same time last year. The increased production is expected on the back of a continued rise in export demand, further improvement in prices, significant improvements in mine productivity, a weak Australian dollar and the probability of new projects and mine extensions going into operation. The improved returns have also flowed into rising valuations for listed coal miners. Over the last year, coal miners such as MIM and Gympie Gold, have delighted in share price gains of 12 per cent and 55 per cent respectively. These sort of performances are being repeated across the Australian industry

  3. Color stability of nanocomposites polished with one-step systems.

    Science.gov (United States)

    Ergücü, Zeynep; Türkün, L Sebnem; Aladag, Akin

    2008-01-01

    This study compared the color changes of five novel resin composites polished with two one-step polishing systems when exposed to coffee solution. The resin composites tested were Filtek Supreme XT, Grandio, CeramX, Premise and Tetric EvoCeram. A total of 150 discs (30/resin composites, 10 x 2 mm) were fabricated. Ten specimens/resin composites cured under Mylar strips served as the control. The other samples were polished with PoGo and OptraPol discs for 30 seconds using a slow speed handpiece and immersed in coffee (Nescafé) for seven days. Color measurements were made with Vita Easyshade at baseline and after one and seven days. Repeated Measures ANOVA and Bonferroni tests were used for statistical analyses (pGrandio, there were no significant differences between the Mylar and PoGo groups, while the most stain resistant surfaces were attained with OptraPol. Removing the outermost resin layer by polishing procedures is essential to achieving a stain resistant, more esthetically stable surface. One-step polishing systems can be used successfully for polishing nanocomposites.

  4. Factors influencing the surface quality of polished tool steels

    International Nuclear Information System (INIS)

    Rebeggiani, S; Rosén, B-G

    2014-01-01

    Today’s demands on surface quality of moulds for injection moulding of plastic components involve no/low defect contents and roughness levels in the nm-range for high gloss applications. Material properties as well as operating conditions influence the mould finish, and thus the final surface of moulded products. This paper focuses on how particle content and different polishing strategies influence final surface qualities of moulds. Visual estimations of polished tool steel samples were combined with non-contact 3D-surface texture analysis in order to correlate traditional assessments to more quantitative methods, and to be able to analyse the surfaces at nanometre-level. It was found that steels with a lower proportion of particles, like carbides and oxides, gave rise to smoother polished surfaces. In a comparative study of polishers from different polishing shops, it was found that while different surface preparation strategies can lead to similar final roughness, similar preparation techniques can produce high-quality surfaces from different steel grades. However, the non-contact 3D-surface texture analysis showed that not all smooth polished surfaces have desirable functional topographies for injection moulding of glossy plastic components. (paper)

  5. Advanced method for the characterization of polishing suspensions

    Science.gov (United States)

    Trum, Christian J.; Sitzberger, Sebastian; Rascher, Rolf

    2017-06-01

    The industrial production of components for applications in the area of precision optics has a long-standing tradition in Germany. As in almost all branches of industry, the external circumstances, processes and products have changed over time. Large lots are becoming less frequent and the demand for special components is growing. In order to meet these requirements, it is necessary to adapt the production processes quickly and flexibly. In the field of chemo-mechanical polishing (CMP), this means that in addition to the process parameters such as speed, pressure and feed, the task-specific adaptation of suspension and polishing pad carriers gain in importance. Along with these changes, it is becoming increasingly important to compare and evaluate the properties of the various polishing suspensions. The procedures according to DIN 58750-3 and DIN 58750-4 are suitable for this purpose. Due to the clearly defined procedures and the constant boundary conditions, different suspensions can be compared and evaluated. The study presented here shows that this method can also lead to misinterpretations. Known relationships, such as the influence of the polishing pad, the concentration of the suspension and the influence of the processed materials play an important role. An extension of the procedure of DIN 58750-3 for the test of a polishing agent can help in a task-specific characterization of polishing slurries.

  6. Polish university as an (unattractive potential employer

    Directory of Open Access Journals (Sweden)

    Baruk, Agnieszka Izabela

    2017-12-01

    Full Text Available The article presents issues associated with the reasons for the fact that young potential employees are not interested in starting work at Polish universities. The article is theoretical-empirical in character. The theoretical part highlights the importance of a situation in which an entity is regarded as an attractive employer, which allows attracting the best employees. Particular attention is paid to the fact that a university needs to build its image as an employer, which results from its characteristics. The article strives to achieve three research goals, among others, identifying the reasons why respondents are not interested in starting work at a university and arranging these reasons hierarchically. Two research hypotheses were subject to preliminary verification: H1 – the main reason for the unwillingness to start work at a university are financial aspects; H2 – the main reason for the unwillingness to start work at a university are the aspects of prestige. The data collected in course of primary research were subject to quantitative analysis based on the method of average assessment analysis and the method of factor analysis. Their results show that the respondents were not interested in work at a university mainly because they wanted to test the knowledge and skills acquired during studies in other branches. At the same time, the aspects of finances and prestige didn’t play a major role. Thus, in case of the surveyed sample of respondents both research hypotheses have to be recognized as untrue.

  7. ECOLOGICAL IDEAS IN POLISH ARCHITECTURE - ENVIRONMENTAL IMPACT

    Directory of Open Access Journals (Sweden)

    Magdalena SZPYTMA

    2016-06-01

    Full Text Available Solutions in the field of ecological architecture appear more and more often in Poland. There are two approaches to eco-design: high-tech and low-tech. High-tech focuses on the use of the latest technological solvings. These means are often used in newly designed commercial buildings, such as the first Polish office building which uses passive technology, built in Katowice, in Euro-Centrum Science and Technology Park. It is intended especially for companies focusing on energy observance issues. Low-tech is usually used in small-scale buildings (for example a cottage in Jartypory village, and is focused on the use of inexpensive, traditional technologies and the daily conscious management of natural resources. Thinking about the impact on the environment and principles of sustainable development is also present in urban planning. In Siewierz, near Katowice, Poland’s first eco-village is being built, with full infrastructure, high-quality residential buildings, shops, offices and hotels. The range of applied solutions will allow residents for the economical exploitation of these buildings.

  8. Thermodynamical motivation of the Polish energy policy

    Directory of Open Access Journals (Sweden)

    Ziębik Andrzej

    2013-02-01

    Full Text Available Basing on the first and second law of thermodynamics the fundamental trends in the Polish energy policy are analysed, including the aspects of environmental protection. The thermodynamical improvement of real processes (reduction of exergy losses is the main way leading to an improvement of the effectivity of energy consumption. If the exergy loss is economically not justified, we have to do with an error from the viewpoint of the second law analysis. The paper contains a thermodynamical analysis of the ratio of final and primary energy, as well as the analysis of the thermo-ecological cost and index of sustainable development concerning primary energy. Analyses of thermo-ecological costs concerning electricity and centralized heat production have been also carried out. The effect of increasing the share of high-efficiency cogeneration has been analyzed, too. Attention has been paid to an improved efficiency of the transmission and distribution of electricity, which is of special importance from the viewpoint of the second law analysis. The improvement of the energy effectivity in industry was analyzed on the example of physical recuperation, being of special importance from the point of view of exergy analysis.

  9. Personality of Polish gay men and women

    Directory of Open Access Journals (Sweden)

    Marcin Kwiatkowski

    2015-12-01

    Full Text Available Background Sexuality is a part of one’s identity and personality that is shaped under the influence of biological and environmental factors and interactions with society. The results of research conducted so far and concerning the personality traits of gay men and women are not consistent, and only a small number of them concern the Polish population. Hence the objective of the present research was to provide personality profiles of men and women with different sexual orientations. Participants and procedure The participants (N = 346 included 84 gay women, 82 gay men, 95 heterosexual women and 85 heterosexual men. The following measures were used: a survey developed by the author, the Kinsey Scale, the EPQ-R (Eysenck Personality Questionnaire Revised adapted by Brzozowski and Drwal (1995, and the Sixteen-factor Personality Questionnaire of Cattell adapted by Nowakowska (1970. Results The results support the hypothesis that gay women and heterosexual men share similar personality traits, while gay men have more diverse traits, similar to the traits typical for heterosexual women and men. In particular, personalities of gay men are described by such traits as progressive attitude, independence, or willingness to take risks, which means traits linked to factor Q1. The highest values of that factor are observable in the case of gay men, as compared to gay women, and also in comparison with heterosexual men and women. Conclusions Sexual orientation is responsible for differences in personality traits of the studied group to a greater extent than their biological sex.

  10. Marketing Globalisation – Polish Market Experience

    Directory of Open Access Journals (Sweden)

    Robert Nowacki

    2007-09-01

    Full Text Available The beginning of the 21st century has been yielded with an acceleration of transformations occurring in economies of the whole world. These changes relate to all the areas of economic life functioning. The most important manifestation thereof is a reinforcement of competitive phenomena. Among the most important reasons for such a state of affairs, there is mentioned globalisation. The course of its processes forces the organisation operating in the market to undertake adaptive actions. One of them is reorientation of marketing activities. The need to modify the previous marketing concepts results, first of all, from far reaching alterations in the sphere of consumption, just triggered by globalisationís impact. These trends are noticed in all the markets, also in the Polish one. The foreign enterprises operating in it more and more often use the concept of global marketing. This makes us to have reflection on what is the real effectiveness of such actions and what are the possibilities to form oneís competitive position owing to that. The article constitutes an attempt to provide answers to these questions.

  11. Automated visual inspection for polished stone manufacture

    Science.gov (United States)

    Smith, Melvyn L.; Smith, Lyndon N.

    2003-05-01

    Increased globalisation of the ornamental stone market has lead to increased competition and more rigorous product quality requirements. As such, there are strong motivators to introduce new, more effective, inspection technologies that will help enable stone processors to reduce costs, improve quality and improve productivity. Natural stone surfaces may contain a mixture of complex two-dimensional (2D) patterns and three-dimensional (3D) features. The challenge in terms of automated inspection is to develop systems able to reliably identify 3D topographic defects, either naturally occurring or resulting from polishing, in the presence of concomitant complex 2D stochastic colour patterns. The resulting real-time analysis of the defects may be used in adaptive process control, in order to avoid the wasteful production of defective product. An innovative approach, using structured light and based upon an adaptation of the photometric stereo method, has been pioneered and developed at UWE to isolate and characterize mixed 2D and 3D surface features. The method is able to undertake tasks considered beyond the capabilities of existing surface inspection techniques. The approach has been successfully applied to real stone samples, and a selection of experimental results is presented.

  12. Coal surface control for advanced physical fine coal cleaning technologies

    Energy Technology Data Exchange (ETDEWEB)

    Morsi, B.I.; Chiang, S.H.; Sharkey, A.; Blachere, J.; Klinzing, G.; Araujo, G.; Cheng, Y.S.; Gray, R.; Streeter, R.; Bi, H.; Campbell, P.; Chiarlli, P.; Ciocco, M.; Hittle, L.; Kim, S.; Kim, Y.; Perez, L.; Venkatadri, R.

    1992-01-01

    This final report presents the research work carried out on the Coal Surface Control for Advanced Physical Fine Coal Cleaning Technologies project, sponsored by the US Department of Energy, Pittsburgh Energy Technology Center (DOE/PETC). The project was to support the engineering development of the selective agglomeration technology in order to reduce the sulfur content of US coals for controlling SO[sub 2] emissions (i.e., acid rain precursors). The overall effort was a part of the DOE/PETCs Acid Rain Control Initiative (ARCI). The overall objective of the project is to develop techniques for coal surface control prior to the advanced physical fine coal cleaning process of selective agglomeration in order to achieve 85% pyrite sulfur rejection at an energy recovery greater than 85% based on run-of-mine coal. The surface control is meant to encompass surface modification during grinding and laboratory beneficiation testing. The project includes the following tasks: Project planning; methods for analysis of samples; development of standard beneficiation test; grinding studies; modification of particle surface; and exploratory R D and support. The coal samples used in this project include three base coals, Upper Freeport - Indiana County, PA, Pittsburgh NO. 8 - Belmont County, OH, and Illinois No. 6 - Randolph County, IL, and three additional coals, Upper Freeport - Grant County- WV, Kentucky No. 9 Hopkins County, KY, and Wyodak - Campbell County, WY. A total of 149 drums of coal were received.

  13. Study on chemical mechanical polishing of silicon wafer with megasonic vibration assisted.

    Science.gov (United States)

    Zhai, Ke; He, Qing; Li, Liang; Ren, Yi

    2017-09-01

    Chemical mechanical polishing (CMP) is the primary method to realize the global planarization of silicon wafer. In order to improve this process, a novel method which combined megasonic vibration to assist chemical mechanical polishing (MA-CMP) is developed in this paper. A matching layer structure of polishing head was calculated and designed. Silicon wafers are polished by megasonic assisted chemical mechanical polishing and traditional chemical mechanical polishing respectively, both coarse polishing and precision polishing experiments were carried out. With the use of megasonic vibration, the surface roughness values Ra reduced from 22.260nm to 17.835nm in coarse polishing, and the material removal rate increased by approximately 15-25% for megasonic assisted chemical mechanical polishing relative to traditional chemical mechanical polishing. Average Surface roughness values Ra reduced from 0.509nm to 0.387nm in precision polishing. The results show that megasonic assisted chemical mechanical polishing is a feasible method to improve polishing efficiency and surface quality. The material removal and finishing mechanisms of megasonic vibration assisted polishing are investigated too. Copyright © 2017 Elsevier B.V. All rights reserved.

  14. Application and Prospects of High-strength Lightweight Materials used in Coal mine

    Science.gov (United States)

    He, Pan

    2017-09-01

    This paper describes some high-strength lightweight materials used in coal mine, and if their performance can meet the requirements of underground safety for explosion-proof, anti-static, friction sparks mine; and reviewed the species, characteristic, preparation process of high-strength lightweight materials for having inspired lightweight high-strength performance by modifying or changing the synthesis mode used in coal mine equipment.

  15. New projects for CCGTs with coal gasification (Review)

    Science.gov (United States)

    Olkhovskii, G. G.

    2016-10-01

    Perspectives of using coal in combined-cycle gas turbine units (CCGTs), which are significantly more efficient than steam power plants, have been associated with preliminary coal gasification for a long time. Due to gasification, purification, and burning the resulting synthesis gas at an increased pressure, there is a possibility to intensify the processes occurring in them and reduce the size and mass of equipment. Physical heat evolving from gasification can be used without problems in the steam circuit of a CCGT. The downside of these opportunities is that the unit becomes more complex and expensive, and its competitiveness is affected, which was not achieved for CCGT power plants with coal gasification built in the 1990s. In recent years, based on the experience with these CCGTs, several powerful CCGTs of the next generation, which used higher-output and cost-effective gas-turbine plants (GTPs) and more advanced systems of gasification and purification of synthesis gas, were either built or designed. In a number of cases, the system of gasification includes devices of CO vapor reforming and removal of the emitted CO2 at a high pressure prior to fuel combustion. Gasifiers with air injection instead of oxygen injection, which is common in coal chemistry, also find application. In this case, the specific cost of the power station considerably decreases (by 15% and more). In units with air injection, up to 40% air required for separation is drawn from the intermediate stage of the cycle compressor. The range of gasified coals has broadened. In order to gasify lignites in one of the projects, a transfer reactor was used. The specific cost of a CCGT with coal gasification rose in comparison with the period when such units started being designed, from 3000 up to 5500 dollars/kW.

  16. Characterization of Coal Porosity for Naturally Tectonically Stressed Coals in Huaibei Coal Field, China

    Science.gov (United States)

    Li, Xiaoshi; Hou, Quanlin; Li, Zhuo; Wei, Mingming

    2014-01-01

    The enrichment of coalbed methane (CBM) and the outburst of gas in a coal mine are closely related to the nanopore structure of coal. The evolutionary characteristics of 12 coal nanopore structures under different natural deformational mechanisms (brittle and ductile deformation) are studied using a scanning electron microscope (SEM) and low-temperature nitrogen adsorption. The results indicate that there are mainly submicropores (2~5 nm) and supermicropores (coal and mesopores (10~100 nm) and micropores (5~10 nm) in brittle deformed coal. The cumulative pore volume (V) and surface area (S) in brittle deformed coal are smaller than those in ductile deformed coal which indicates more adsorption space for gas. The coal with the smaller pores exhibits a large surface area, and coal with the larger pores exhibits a large volume for a given pore volume. We also found that the relationship between S and V turns from a positive correlation to a negative correlation when S > 4 m2/g, with pore sizes coal. The nanopore structure (coal. PMID:25126601

  17. Numerical investigation on performance of coal gasification under various injection patterns in an entrained flow gasifier

    International Nuclear Information System (INIS)

    Chen, Chih-Jung; Hung, Chen-I.; Chen, Wei-Hsin

    2012-01-01

    Highlights: ► A numerical method is developed to predict coal gasification phenomena. ► Particular emphasis is placed on the influence of injection pattern upon syngas production. ► The parameter of steam/coal ratio is also taken into account. ► The appropriate injection for the performance of coal gasification is suggested. ► The obtained results have provided a useful insight into the operation of coal gasification. -- Abstract: Gasification plays an important role in the development of clean coal technology. To seek appropriate operations for synthesis gas (syngas) formation, the present study develops a numerical method to predict coal gasification phenomena in an entrained-flow gasifier. Particular emphasis is placed on the influence of injection pattern upon syngas production. The parameter of steam/coal ratio is also taken into account to evaluate its impact on hydrogen generation. The simulations suggest that the developed numerical method is able to provide an accurate prediction on syngas formation. With oxygen injected from the center inlet and coal from the middle ring inlet of the reactor, the operating pattern gives the best performance of coal gasification where the carbon conversion (CC) and coal gas efficiency (CGE) are 89% and 72%, respectively. Increasing steam into the reactor reduces CC and less CO is generated. Nevertheless, more H 2 is produced stemming from water gas shift reaction. This results in slight variation in CGE with altering steam/coal ratio. The obtained results have provided a useful insight into the operation of fuel and oxidant injection for coal gasification.

  18. Biological production of ethanol from coal. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1992-12-01

    Due to the abundant supply of coal in the United States, significant research efforts have occurred over the past 15 years concerning the conversion of coal to liquid fuels. Researchers at the University of Arkansas have concentrated on a biological approach to coal liquefaction, starting with coal-derived synthesis gas as the raw material. Synthesis gas, a mixture of CO, H{sub 2}, CO{sub 2}, CH{sub 4} and sulfur gases, is first produced using traditional gasification techniques. The CO, CO{sub 2} and H{sub 2} are then converted to ethanol using a bacterial culture of Clostridium 1jungdahlii. Ethanol is the desired product if the resultant product stream is to be used as a liquid fuel. However, under normal operating conditions, the ``wild strain`` produces acetate in favor of ethanol in conjunction with growth in a 20:1 molar ratio. Research was performed to determine the conditions necessary to maximize not only the ratio of ethanol to acetate, but also to maximize the concentration of ethanol resulting in the product stream.

  19. Geomorphology of coal seam fires

    Science.gov (United States)

    Kuenzer, Claudia; Stracher, Glenn B.

    2012-02-01

    Coal fires occur in underground natural coal seams, in exposed surface seams, and in coal storage or waste piles. The fires ignite through spontaneous combustion or natural or anthropogenic causes. They are reported from China, India, USA, South Africa, Australia, and Russia, as well as many other countries. Coal fires lead to loss of a valuable resource (coal), the emission of greenhouse-relevant and toxic gases, and vegetation deterioration. A dangerous aspect of the fires is the threat to local mines, industries, and settlements through the volume loss underground. Surface collapse in coal fire areas is common. Thus, coal fires are significantly affecting the evolution of the landscape. Based on more than a decade of experience with in situ mapping of coal fire areas worldwide, a general classification system for coal fires is presented. Furthermore, coal seam fire geomorphology is explained in detail. The major landforms associated with, and induced by, these fires are presented. The landforms include manifestations resulting from bedrock surface fracturing, such as fissures, cracks, funnels, vents, and sponges. Further manifestations resulting from surface bedrock subsidence include sinkholes, trenches, depressions, partial surface subsidence, large surface subsidence, and slides. Additional geomorphologic coal fire manifestations include exposed ash layers, pyrometamorphic rocks, and fumarolic minerals. The origin, evolution, and possible future development of these features are explained, and examples from in situ surveys, as well as from high-resolution satellite data analyses, are presented. The geomorphology of coal fires has not been presented in a systematic manner. Knowledge of coal fire geomorphology enables the detection of underground coal fires based on distinct surface manifestations. Furthermore, it allows judgments about the safety of coal fire-affected terrain. Additionally, geomorphologic features are indicators of the burning stage of fires

  20. The Charfuel coal refining process

    International Nuclear Information System (INIS)

    Meyer, L.G.

    1991-01-01

    The patented Charfuel coal refining process employs fluidized hydrocracking to produce char and liquid products from virtually all types of volatile-containing coals, including low rank coal and lignite. It is not gasification or liquefaction which require the addition of expensive oxygen or hydrogen or the use of extreme heat or pressure. It is not the German pyrolysis process that merely 'cooks' the coal, producing coke and tar-like liquids. Rather, the Charfuel coal refining process involves thermal hydrocracking which results in the rearrangement of hydrogen within the coal molecule to produce a slate of co-products. In the Charfuel process, pulverized coal is rapidly heated in a reducing atmosphere in the presence of internally generated process hydrogen. This hydrogen rearrangement allows refinement of various ranks of coals to produce a pipeline transportable, slurry-type, environmentally clean boiler fuel and a slate of value-added traditional fuel and chemical feedstock co-products. Using coal and oxygen as the only feedstocks, the Charfuel hydrocracking technology economically removes much of the fuel nitrogen, sulfur, and potential air toxics (such as chlorine, mercury, beryllium, etc.) from the coal, resulting in a high heating value, clean burning fuel which can increase power plant efficiency while reducing operating costs. The paper describes the process, its thermal efficiency, its use in power plants, its pipeline transport, co-products, environmental and energy benefits, and economics

  1. Controls on coal cleat spacing

    Energy Technology Data Exchange (ETDEWEB)

    Dawson, G.K.W.; Esterle, J.S. [School of Earth Sciences, The University of Queensland, Brisbane, Queensland 4072 (Australia)

    2010-06-01

    This study was undertaken to determine the relationship between cleat spacing, cleat height and coal banding texture for Queensland Permian age coals of different rank, four of which are presented here. Whereas relationships between cleat frequency and rank, and with coal type or grade, have been reported in the past, relationships between the spacing and height among the different kinds of cleats are not quantitatively established. For other layered sedimentary rocks, joint or fracture spacing relates directly to both bed thickness and rock strength. Coal is similar to other layered rocks. Four major classes of cleats were distinguished, which were separate data populations when cleat spacing was plotted against cleat height; master cleats, single vitrain layer cleats, multiple vitrain layer package cleats, and durain (dull coal) cleats. Understanding the relationship between cleat height and spacing for specific coals, and the specific kinds of cleats within those coals, will lead to more accurate predictions of cleat density and hence coal permeability. This can improve modelling and prediction of methane gas deliverability in coal seams. In the Australian Permian coals studied, narrowly spaced cleats exist at all ranks, but the distribution of cleat spacing with cleat height is what varies for specific cleat classes. Cleat spacing was found to be directly proportional to cleat height in most cases. (author)

  2. Coal slurries: An environmental bonus?

    International Nuclear Information System (INIS)

    Basta, N.; Moore, S.; Ondrey, G.

    1994-01-01

    Developers and promoters of coal-water slurries and similar CWF (coal-water fuel) technologies have had a hard time winning converts since they unveiled their first commercial processes in the 1970s. The economic appeal of such processes, marginal at best, varies with the price of oil. Nevertheless, the technology is percolating, as geopolitics and environmental pressures drive new processes. Such fuels are becoming increasingly important to coal-rich, oil-poor nations such as China, as they attempt to build an onshore fuel supply. Meanwhile, improvements are changing the way coal-fired processes are viewed. Where air pollution regulations once discouraged the use of coal fuels, new coal processes have been developed that cut nitrous oxides (NOx) emissions and provide a use for coal fines, previously viewed as waste. The latest developments in the field were all on display at the 19th International Technical Conference on Coal Utilization and Fuel Systems, held in Clearwater, Fla., on March 21--24. At this annual meeting, sponsored by the Coal and Slurry Technology Association, (Washington, D.C.) and the Pittsburgh Energy Technology Center of the US Dept. of Energy (PETC), some 200 visitors from around the work gathered to discuss the latest developments in coal slurry utilization--new and improved processes, and onstream plants. This paper presents highlights from the conference

  3. Utilisation of chemically treated coal

    Directory of Open Access Journals (Sweden)

    Bežovská Mária

    2002-03-01

    Full Text Available The numerous application of coal with high content of humic substances are known. They are used in many branches of industry. The complex study of the composition of coal from upper Nitra mines has directed research to its application in the field of ecology and agriculture. The effective sorption layers of this coal and their humic acids can to trap a broad spectrum of toxic harmful substances present in industrial wastes, particularly heavy metals. A major source of humic acids is coal - the most abundant and predominant product of plant residue coalification. All ranks of coal containt humic acids but lignite from Nováky deposit represents the most easily available and concentrated form of humic acids. Deep oxidation of coal by HNO3 oxidation - degradation has been performed to produce water-soluble-organic acids. The possibilities of utilisation of oxidised coal and humic acids to remove heavy metals from waste waters was studied. The residual concentrations of the investigated metals in the aqueous phase were determined by AAs. From the results follows that the samples of oxidised coal and theirs humic acids can be used for the heavy metal removal from metal solutions and the real acid mine water.Oxidised coal with a high content of humic acids and nitrogen is used in agriculture a fertilizer. Humic acids are active component in coal and help to utilize almost quantitatively nitrogen in soil. The humic substances block and stabiliz toxic metal residues already present in soil.

  4. Utilization of coal rejects and coal washery tailings in Yong Rong Power Plant

    International Nuclear Information System (INIS)

    Tao, T.; Kefa, C.; Mingjiang, N.; Guoguan, H.; Yong, C.; Xiang, Z.

    1991-01-01

    The coal rejects and coal washery tailings discharged by coal washery not only occupies farmland but also causes environmental pollution. With the development of coal industry, the problem becomes more serious. In this paper, the properties of coal rejects and coal washery tailings are analyzed. The technology that burn coal rejects and coal washery tailings in boilers to produce electric power is reported. It has been shown the technology is feasible and successful. It saves energy as well as protects the environment

  5. Effect of various polishing systems on the surface roughness and phase transformation of zirconia and the durability of the polishing systems.

    Science.gov (United States)

    Park, Chan; Vang, Mong-Sook; Park, Sang-Won; Lim, Hyun-Pil

    2017-03-01

    Although many systems are used to polish zirconia, a comparison of the performance of zirconia and feldspathic porcelain polishing systems is lacking. The purpose of this in vitro study was to compare the effects of 3 polishing systems on surface roughness, zirconia phase transformation, and durability of the polishing systems when applied to zirconia and feldspathic porcelain. Three polishing systems were evaluated: Z1, a zirconia polishing system; Z2, a zirconia polishing system, and F1, a feldspathic porcelain polishing system. Three ceramic systems were evaluated: PR and ZM zirconia specimens (diameter 15 mm, height 2 mm; 23 specimens each) and CB feldspathic porcelain specimens of the same size (15 specimens). A rough surface was created on the 3 types of specimens (15 specimens each) to model an occlusal adjustment under the same conditions. Polishing was carried out with the 3 polishing systems for 2 minutes each. Surface roughness was measured with a 3-dimensional (3D) optical profiler. The surface was also observed with a scanning electron microscopy. X-ray diffraction analysis was performed for 8 PR or ZM zirconia specimens polished by using the Z1 and Z2 systems for 8 minutes to evaluate the phase transformation of zirconia before, during, and after polishing. These specimens were compared and analyzed for phase transformation that might have occurred during the polishing of the specimens. After finishing the surface roughness experiment and the phase transformation experiment, the volumes of the polishers were measured with a 3D volume scanner and compared with those before the experiments to evaluate the durability of the polishing system. A statistical analysis of all data was performed using 2-way ANOVA and the Tukey honest significant difference test (α=.05). The 2 zirconia polishing systems (Z1, Z2) created a significantly (Pzirconia specimens for 8 minutes, the maximum percentages of monoclinic phase increased by 0.03% in the Z1 system and by 0

  6. Computer-Controlled Cylindrical Polishing Process for Development of Grazing Incidence Optics for Hard X-Ray Region

    Science.gov (United States)

    Khan, Gufran Sayeed; Gubarev, Mikhail; Speegle, Chet; Ramsey, Brian

    2010-01-01

    The presentation includes grazing incidence X-ray optics, motivation and challenges, mid spatial frequency generation in cylindrical polishing, design considerations for polishing lap, simulation studies and experimental results, future scope, and summary. Topics include current status of replication optics technology, cylindrical polishing process using large size polishing lap, non-conformance of polishin lap to the optics, development of software and polishing machine, deterministic prediction of polishing, polishing experiment under optimum conditions, and polishing experiment based on known error profile. Future plans include determination of non-uniformity in the polishing lap compliance, development of a polishing sequence based on a known error profile of the specimen, software for generating a mandrel polishing sequence, design an development of a flexible polishing lap, and computer controlled localized polishing process.

  7. Desulfurizing Coal By Chlorinolysis and Hydrogenation

    Science.gov (United States)

    Kalvinskas, J. J.; Rohatgi, N. K.

    1983-01-01

    85 percent of organic and pyritic sulfur in coal removed by combination of chlorinolysis and hydrogeneration. Coal is fed to hydrogenator after chlorination. Coal flows against hydrogen current increasing mixing and reducing hydrogen consumption. Excess hydrogen is recovered from gaseous reaction products. Product coal contained 62.5 percent less total sulfur than same coal after chlorination.

  8. Bulk analysis of coal

    International Nuclear Information System (INIS)

    Sowerby, B.D.

    1982-01-01

    Nuclear techniques used in the coal industry to determine specific energy, ash and moisture are outlined. Ash analysis by radioisotope X-ray techniques include a single X-ray measurement using a transmission or backscatter geometry and techniques with compensation for iron variations. Neutron techniques can be used to measure the concentration of some specific elements in coal. The measurement of specific energy, ash and moisture then depends on the correlation of the particular parameter with the measured elemental composition. Carbon can be determined by a combination of a measurement of 4.43 MeV 12 C gamma-rays from neutron inelastic scattering with a separate 60 Co gamma-ray scattering measurement. Sulphur meters are based on the measurement of 5.42 MeV neutron capture of gamma rays

  9. Coal mine subsidence

    International Nuclear Information System (INIS)

    Rahall, N.J.

    1991-05-01

    This paper examines the efficacy of the Department of the Interior's Office of Surface Mining Reclamation and Enforcement's (OSMRE) efforts to implement the federally assisted coal mine subsidence insurance program. Coal mine subsidence, a gradual settling of the earth's surface above an underground mine, can damage nearby land and property. To help protect property owners from subsidence-related damage, the Congress passed legislation in 1984 authorizing OSMRE to make grants of up to $3 million to each state to help the states establish self-sustaining, state-administered insurance programs. Of the 21 eligible states, six Colorado, Indiana, Kentucky, Ohio, West Virginia, and Wyoming applied for grants. This paper reviews the efforts of these six states to develop self-sustaining insurance programs and assessed OSMRE's oversight of those efforts

  10. Antagonist wear by polished zirconia crowns.

    Science.gov (United States)

    Hartkamp, Oliver; Lohbauer, Ulrich; Reich, Sven

    The aim of this in vivo study was to measure antagonist wear caused by polished monolithic posterior zirconia crowns over a 24-month period using the intraoral digital impression (IDI) technique. Thirteen zirconia crowns were placed in nine patients. The crowns and adjacent teeth were captured using an intraoral scanner (Lava C.O.S.). The corresponding antagonist teeth and the respective neighboring teeth were also scanned. Scanning was performed immediately after the restoration (baseline) as well as 12 and 24 months after crown placement. Geomagic Qualify software was used to superimpose the follow-up data sets onto the corresponding baseline data set, identify wear sites, and measure maximum vertical height loss in each individual wear site. Overall antagonist wear was then determined as the mean of wear rates measured in all of the individual antagonist units. In addition, wear rates in enamel and ceramic antagonists were analyzed as part of the scope of this study. The maximum mean wear with standard deviation (SD) in the overall sample with a total of nine patients, 13 antagonist units, and 98 evaluable wear sites was 86 ± 23 µm at 12 months, and 103 ± 39 µm at 24 months. The maximum mean wear in the enamel antagonist subgroup was 87 ± 41 µm at 12 months, and 115 ± 71 µm at 24 months; and in the ceramic antagonist subgroup 107 ± 22 µm at 12 months, and 120 ± 27 µm at 24 months. The wear rates determined in this study are comparable to those of existing studies. The IDI technique of wear analysis can be carried out in a practical manner and produces useful results.

  11. Flotation and flocculation chemistry of coal and oxidized coals

    Energy Technology Data Exchange (ETDEWEB)

    Somasundaran, P.

    1990-01-01

    The objective of this research project is to understand the fundamentals involved in the flotation and flocculation of coal and oxidized coals and elucidate mechanisms by which surface interactions between coal and various reagents enhance coal beneficiation. An understanding of the nature of the heterogeneity of coal surfaces arising from the intrinsic distribution of chemical moieties is fundamental to the elucidation of mechanism of coal surface modification and its role in interfacial processes such as flotation, flocculation and agglomeration. A new approach for determining the distribution in surface properties of coal particles was developed in this study and various techniques capable of providing such information were identified. Distributions in surface energy, contact angle and wettability were obtained using novel techniques such as centrifugal immersion and film flotation. Changes in these distributions upon oxidation and surface modifications were monitored and discussed. An approach to the modelling of coal surface site distributions based on thermodynamic information obtained from gas adsorption and immersion calorimetry is proposed. Polyacrylamide and dodecane was used to alter the coal surface. Methanol adsorption was also studied. 62 figs.

  12. Health impacts of coal and coal use: Possible solutions

    Science.gov (United States)

    Finkelman, R.B.; Orem, W.; Castranova, V.; Tatu, C.A.; Belkin, H.E.; Zheng, B.; Lerch, H.E.; Maharaj, S.V.; Bates, A.L.

    2002-01-01

    Coal will be a dominant energy source in both developed and developing countries for at least the first half of the 21st century. Environmental problems associated with coal, before mining, during mining, in storage, during combustion, and postcombustion waste products are well known and are being addressed by ongoing research. The connection between potential environmental problems with human health is a fairly new field and requires the cooperation of both the geoscience and medical disciplines. Three research programs that illustrate this collaboration are described and used to present a range of human health problems that are potentially caused by coal. Domestic combustion of coal in China has, in some cases, severely affected human health. Both on a local and regional scale, human health has been adversely affected by coals containing arsenic, fluorine, selenium, and possibly, mercury. Balkan endemic nephropathy (BEN), an irreversible kidney disease of unknown origin, has been related to the proximity of Pliocene lignite deposits. The working hypothesis is that groundwater is leaching toxic organic compounds as it passes through the lignites and that these organics are then ingested by the local population contributing to this health problem. Human disease associated with coal mining mainly results from inhalation of particulate matter during the mining process. The disease is Coal Worker's Pneumoconiosis characterized by coal dust-induced lesions in the gas exchange regions of the lung; the coal worker's "black lung disease". ?? 2002 Elsevier Science B.V. All rights reserved.

  13. New Hope Coal Australia: leaders in thin seam coal mining

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    New Hope Corporation Ltd.'s coal activities in Queensland are conducted under the business name of New Hope Coal Australia and comprise open-cut mines in the West Moreton coal fields, 40 km west of Brisbane. The company gained an award for its reject co-disposal system and another for its organic overburden conditioning programme. Walloon coal from the Jeebropilly and New Oakleigh open-cut mines has characteristics which are making it increasingly popular as power plant fuel. The article describes operations at these mines and also at Swanbank and Acland. Other projects with which New Hope is involved are mentioned. 4 photos.

  14. Phenanthrene sorption to Chinese coal: Importance of coal's geochemical properties

    International Nuclear Information System (INIS)

    Yan Caixia; Yang Yi; Liu Min; Nie Minghua; Zhou, John L.

    2011-01-01

    Highlights: → Phen was chosen as the probe compound for determining the sorption of PAHs to a series of different Chinese coal samples. → The combined partition and adsorption model yielded a better fit than the Freundlich isotherm. → Compared to total carbon, BC might play more important role in the sorption of Phen to coal samples. → Relationships between aromatic and aliphatic carbon contents and sorption parameters indicated the significance of aromatic and aliphatic carbon in the coal sorption behavior. - Abstract: Phenanthrene (Phen) was chosen as the probe compound for determining the sorption of PAHs to a series of different coal samples from China. Based on elemental analysis and nuclear magnetic resonance (NMR) spectra analysis, coal samples were characterized with different metamorphic evolutional degrees. The experimental sorption data were fitted well by the Freundlich model, suggesting enhanced sorption capacity and strong nonlinearity of coal samples. The combined partition and adsorption model yielded a better fit than the Freundlich isotherm, indicating that adsorption dominated the sorption at low aqueous concentrations. Correlations between coal properties and sorption capacity values indicated that C%, H/C and O/C atomic ratios were the key factors controlling the sorption behavior. Compared to total carbon, BC might play more important role in the sorption of Phen to coal samples. Moreover, there existed nonlinear relationships between combined carbon, aromatic and aliphatic carbon contents and log K Fr and n values, respectively, indicating the significance of aromatic and aliphatic carbon in the coal sorption behavior.

  15. Coal Bed Methane Primer

    Energy Technology Data Exchange (ETDEWEB)

    Dan Arthur; Bruce Langhus; Jon Seekins

    2005-05-25

    During the second half of the 1990's Coal Bed Methane (CBM) production increased dramatically nationwide to represent a significant new source of income and natural gas for many independent and established producers. Matching these soaring production rates during this period was a heightened public awareness of environmental concerns. These concerns left unexplained and under-addressed have created a significant growth in public involvement generating literally thousands of unfocused project comments for various regional NEPA efforts resulting in the delayed development of public and fee lands. The accelerating interest in CBM development coupled to the growth in public involvement has prompted the conceptualization of this project for the development of a CBM Primer. The Primer is designed to serve as a summary document, which introduces and encapsulates information pertinent to the development of Coal Bed Methane (CBM), including focused discussions of coal deposits, methane as a natural formed gas, split mineral estates, development techniques, operational issues, producing methods, applicable regulatory frameworks, land and resource management, mitigation measures, preparation of project plans, data availability, Indian Trust issues and relevant environmental technologies. An important aspect of gaining access to federal, state, tribal, or fee lands involves education of a broad array of stakeholders, including land and mineral owners, regulators, conservationists, tribal governments, special interest groups, and numerous others that could be impacted by the development of coal bed methane. Perhaps the most crucial aspect of successfully developing CBM resources is stakeholder education. Currently, an inconsistent picture of CBM exists. There is a significant lack of understanding on the parts of nearly all stakeholders, including industry, government, special interest groups, and land owners. It is envisioned the Primer would being used by a variety of

  16. Coal liquefaction and hydrogenation

    Science.gov (United States)

    Schindler, Harvey D.

    1985-01-01

    The coal liquefaction process disclosed uses three stages. The first stage is a liquefaction. The second and third stages are hydrogenation stages at different temperatures and in parallel or in series. One stage is within 650.degree.-795.degree. F. and optimizes solvent production. The other stage is within 800.degree.-840.degree. F. and optimizes the C.sub.5 -850.degree. F. product.

  17. Coal - testing methods

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2005-04-01

    This Standard specifies the method for the particle-size analysis, the method for determination of the float and sink characteristics, the method for determination of Hardgrove grindability indices, the method for determination of the crucible swelling number, the method for determination of the swelling properties, the method for determination of the fluidity properties, the method for determination of the coking properties, the method for determination of the fusibility of ash, and the method for determination of Roga indices of coal.

  18. Studies on polishing of Ti and Ag-Pd-Cu-Au alloy with five dental abrasives.

    Science.gov (United States)

    Hirata, T; Nakamura, T; Takashima, F; Maruyama, T; Taira, M; Takahashi, J

    2001-08-01

    Titanium (Ti) and Ag-Pd-Cu-Au alloy were examined for their polishing behaviour by conducting manually controlled polishing tests using five dental abrasives [carborundum point (CR) and silicone points (R1 and R2)] driven by a high torque micromotor with rotational speeds ranging from 2000 to 15 000 r.p.m. Polishing of Ti resulted in less volume of removal upon polishing, a rougher surface and larger loss of abrasives, compared with polishing of Ag-Pd-Cu-Au alloy. Polishing of Ti with a rotational speed of 15 000 r.p.m. led to the largest volume of removal upon polishing, whilst that of 10 000 r.p.m. produced the optimal volume for Ag-Pd-Cu-Au alloy. It was concluded that Ti was much more difficult to polish, requiring special care (e.g. frequent exchange of abrasives). Development of new abrasives for polishing Ti is required.

  19. The study of optimization on process parameters of high-accuracy computerized numerical control polishing

    Science.gov (United States)

    Huang, Wei-Ren; Huang, Shih-Pu; Tsai, Tsung-Yueh; Lin, Yi-Jyun; Yu, Zong-Ru; Kuo, Ching-Hsiang; Hsu, Wei-Yao; Young, Hong-Tsu

    2017-09-01

    Spherical lenses lead to forming spherical aberration and reduced optical performance. Consequently, in practice optical system shall apply a combination of spherical lenses for aberration correction. Thus, the volume of the optical system increased. In modern optical systems, aspherical lenses have been widely used because of their high optical performance with less optical components. However, aspherical surfaces cannot be fabricated by traditional full aperture polishing process due to their varying curvature. Sub-aperture computer numerical control (CNC) polishing is adopted for aspherical surface fabrication in recent years. By using CNC polishing process, mid-spatial frequency (MSF) error is normally accompanied during this process. And the MSF surface texture of optics decreases the optical performance for high precision optical system, especially for short-wavelength applications. Based on a bonnet polishing CNC machine, this study focuses on the relationship between MSF surface texture and CNC polishing parameters, which include feed rate, head speed, track spacing and path direction. The power spectral density (PSD) analysis is used to judge the MSF level caused by those polishing parameters. The test results show that controlling the removal depth of single polishing path, through the feed rate, and without same direction polishing path for higher total removal depth can efficiently reduce the MSF error. To verify the optical polishing parameters, we divided a correction polishing process to several polishing runs with different direction polishing paths. Compare to one shot polishing run, multi-direction path polishing plan could produce better surface quality on the optics.

  20. Predicted coal production trends in Kentucky: The results of available coal resources, coal quality demands, and regulatory factors

    International Nuclear Information System (INIS)

    Watson, W.D.

    1993-01-01

    Many factors affect the viability of regional coal production markets including (1) coal quality and recoverable tonnage, (2) coal mining cost, (3) the regional and time varying patterns of coal demand growth, (4) regulations and other institutional constraints that affect coal demand and utilization, and (5) the regional array of coal transport modes and rates. This analysis integrates these factors into an assessment of coal production prospects (separately) for eastern and western Kentucky coal producing counties for the decade of the 90's. The integration indicates that eastern Kentucky coal production will peak and begin to decline by the end of the decade whereas western Kentucky coal production will continue to grow. No single factor explains these trends. There is plenty of available minable coal. The combination of changes in environmental regulations, some increase in coal mining costs, and the mining-out of low sulfur reserves are the main factors that account for the production trends

  1. Coal: a human history

    Energy Technology Data Exchange (ETDEWEB)

    Freese, B.

    2002-12-01

    Prized as 'the best stone in Britain' by Roman invaders who carved jewellery out of it, coal has transformed societies, powered navies, fueled economies, and expanded frontiers. It made China a twelfth-century superpower, inspired the writing of the Communist Manifesto, and helped the northern states win the American Civil War. Yet the mundane mineral that built our global economy - and even today powers our electrical plants - has also caused death, disease, and environmental destruction. As early as 1306, King Edward I tried to ban coal (unsuccessfully) because its smoke became so obnoxious. Its recent identification as a primary cause of global warming has made it a cause celebre of a new kind. In this book, Barbara Freese takes us on an historical journey that begins three hundred million years ago and spans the globe. From the 'Great Stinking Fogs' of London to the rat-infested coal mines of Pennsylvania, from the impoverished slums of Manchester to the toxic city streets of Beijing, this book describes an ordinary substance that has done extraordinary things.

  2. Cleaning and dewatering fine coal

    Energy Technology Data Exchange (ETDEWEB)

    Yoon, Roe-Hoan; Eraydin, Mert K.; Freeland, Chad

    2017-10-17

    Fine coal is cleaned of its mineral matter impurities and dewatered by mixing the aqueous slurry containing both with a hydrophobic liquid, subjecting the mixture to a phase separation. The resulting hydrophobic liquid phase contains coal particles free of surface moisture and droplets of water stabilized by coal particles, while the aqueous phase contains the mineral matter. By separating the entrained water droplets from the coal particles mechanically, a clean coal product of substantially reduced mineral matter and moisture contents is obtained. The spent hydrophobic liquid is separated from the clean coal product and recycled. The process can also be used to separate one type of hydrophilic particles from another by selectively hydrophobizing one.

  3. CVFA: Coal vendor financial advisor

    International Nuclear Information System (INIS)

    Goote, W.G.; Andersen, S.

    1992-01-01

    An expert system for determining coal vendor financial viability in fuel purchasing contracts at an electric utility is described. The system blends rules, data objects, and financial knowledge to provide a rational basis for accepting or rejecting coal contracts given the financial capability of the coal vendor. The discussion concludes with a critique of managerial issues in the development of the system and its use in decision making. 3 refs., 1 fig

  4. Coal resources of Indiana

    Science.gov (United States)

    Spencer, Frank Darwyn

    1953-01-01

    The Indiana coal field forms the eastern edge of the eastern interior coal basin, which is near some of the most densely populated and highly productive manufacturing areas of the United States. (See fig. 1. ) For this reason Indiana coal reserves are an important State and National asset. In dollar value the coal mining industry is the largest of Indiana's natural-resource-producing industries. The total value of coil production for the year 1950 was more than 100 million dollars, or more than that of all other natural-resource industries in the State combined. As estimated herein, the original coal reserves of Indiana total 37,293 million tons, of which 27,320 million tons is contained in beds more than 42 inches thick; 7,632 million tons in beds 28 to 49. inches thick; and 2,341 million tons in beds 14 to 28 inches thick. The remaining reserves as of January 1951, total 35,806 million tons, of which 18,779 million tons is believed to be recoverable. The distribution of the reserves in these several categories is summarized by counties in table 1. Of the total original reserves of 37,293 million tons, 6,355 million tons can be classified as measured; 8,657 million tons as indicated; and 22,281 million tons as inferred. Strippable reserves constitute 3,524 million tons, or 9.5 percent of the total original reserves. The distribution of the strippable and nonstrippable original reserves is summarized in tables 2 and 3 by counties and by several categories, according to the thickness of the beds and the relative abundance and reliability of the information available for preparing the estimates. The distribution of the estimated 18,779 million tons of recoverable strippable and nonstrippable reserves in Indiana is further summarized by counties in table 4, and the information is presented graphically in figures 2 and 3. The tables i to 4 and figures 2 and 3 include beds in the 14- to 28-inch category, because thin beds have been mined in many places. However, many

  5. Infestation of Polish Agricultural Soils by Plasmodiophora Brassicae Along The Polish-Ukrainian Border

    Directory of Open Access Journals (Sweden)

    Jędryczka Małgorzata

    2014-07-01

    Full Text Available There has been a rapid, worldwide increase in oilseed rape production that has resulted in enormous intensification of oilseed rape cultivation, leading to tight rotations. This in turn, has caused an accumulation of pests as well as foliar and soil-borne diseases. Recently, clubroot has become one of the biggest concerns of oilseed rape growers. Clubroot is caused by the soil-borne protist Plasmodiophora brassicae Woronin. The pathogen may be present in groundwater, lakes, and irrigation water used in sprinkling systems. It can be easily transmitted from one field to another not only by water, but also by soil particles and dust transmitted by wind and on machinery. The aim of our overall study was to check for P. brassicae infestation of Polish agricultural soils. This paper presents the 2012 results of a study performed along the Polish-Ukrainian border in two provinces: Lublin (Lubelskie Voivodeship and the Carpathian Foothills (Podkarpackie Voivodeship, in south-east Poland. Monitoring was done in 11 counties, including nine rural and two municipal ones. In total, 40 samples were collected, out of which 36 were collected from fields located in rural areas and four from municipal areas, with two per municipal region. Each sample was collected at 8-10 sites per field, using a soil auger. The biotest to detect the presence of P. brassicae was done under greenhouse conditions using seedlings of the susceptible Brassicas: B. rapa ssp. pekinensis and the Polish variety of oilseed rape B. napus cv. Monolit. Susceptible plants grown in heavily infested soils produced galls on their roots. A county was regarded as free from the pathogen, if none of the bait plants became infected. The pathogen was found in three out of 40 fields monitored (7.5% in the Carpathian Foothill region. The fields were located in two rural counties. The pathogen was not found in Lublin province, and was also not detected in any of the municipal counties. The detection with

  6. Coal: More than silver linings

    International Nuclear Information System (INIS)

    Doerell, P.E.

    1995-01-01

    While last year's coal survey was subtitled open-quotes Less than lacklusterclose quotes because of overproduction and depressed prices, the end of 1994 showed a definitely brighter picture. An indication was the recent attendance and the mood at the CoalTrans '94 Conference in Hamburg, the trade's biggest meeting. This atmosphere was described by many of the 1,300 delegates as open-quotes bullishclose quotes, with coal traders and consumers actually chasing suppliers-a rare occurrence in recent years. The reason for optimism is, of course, the end of the worldwide recession, resulting in increasing coal demand which stabilizes prices

  7. The Global Value of Coal

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2012-07-01

    Coal plays an essential role in our global energy mix, particularly for power generation; and through that to the alleviation of energy poverty. The use of coal continues to grow rapidly and will continue, together with other fuels, to support world economic and social development particularly in rapidly developing world economies such as China and India. The purpose of this paper is to highlight for policy makers the value of coal to world economic and social development and so encourage development of a policy environment that will allow the coal and electricity industries to make the necessary investments in production capacity and CO2 emissions reduction technologies.

  8. World coal perspectives to 2030

    International Nuclear Information System (INIS)

    Brendow, Klaus

    2004-01-01

    In Summer 2004, The World Energy Council published a Study on 'Sustainable Global Energy Development: the Case of Coal'. The Study aims at developing an internationally consistent reply to the question whether and to what extent coal use could be economic and sustainable in meeting global energy demand to 2030 and beyond. It covers markets, trade and demand, mining and combustion technologies, restructuring and international policies, and perspectives. It considers both, the contribution that coal could make to economic development as well as the need for coal adapt to the exigencies of security of supply, local environmental protection and mitigation of climate change. (Author)

  9. Gaseous emissions from coal stockpiles

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2013-01-15

    Stockpiled coal undergoes atmospheric oxidation and desorption processes during open air storage. These processes release gases to the environment which may effect health and safety by their toxicity and flammability. In extreme cases, this could lead to a fire. This report discusses gaseous emissions from coal stockpiles. It covers gas emission mechanisms, and gas sampling and testing methods, before examining in more detail the principal gases that have been emitted. It concludes that there is limited research in this area and more data are needed to evaluate the risks of gaseous emissions. Some methods used to prevent coal self-heating and spontaneous combustion can be applied to reduce emissions from coal stockpiles.

  10. Chemical analyses of coal, coal-associated rocks and coal combustion products collected for the National Coal Quality Inventory

    Science.gov (United States)

    Hatch, Joseph R.; Bullock, John H.; Finkelman, Robert B.

    2006-01-01

    In 1999, the USGS initiated the National Coal Quality Inventory (NaCQI) project to address a need for quality information on coals that will be mined during the next 20-30 years. At the time this project was initiated, the publicly available USGS coal quality data was based on samples primarily collected and analyzed between 1973 and 1985. The primary objective of NaCQI was to create a database containing comprehensive, accurate and accessible chemical information on the quality of mined and prepared United States coals and their combustion byproducts. This objective was to be accomplished through maintaining the existing publicly available coal quality database, expanding the database through the acquisition of new samples from priority areas, and analysis of the samples using updated coal analytical chemistry procedures. Priorities for sampling include those areas where future sources of compliance coal are federally owned. This project was a cooperative effort between the U.S. Geological Survey (USGS), State geological surveys, universities, coal burning utilities, and the coal mining industry. Funding support came from the Electric Power Research Institute (EPRI) and the U.S. Department of Energy (DOE).

  11. Awakening a sleeping coal giant

    Energy Technology Data Exchange (ETDEWEB)

    Baxter, B.

    2007-08-15

    Botswana, a southern African country that in the 1980s could not economically land a tonne of coal at the closest export terminal and even today mines no more than 1 million tpa, is to increase production to beyond 30 million tpa. A first ever coal conference in Gaborone called it the awakening of a coal giant. The alarm call for the coal giant is the realisation that without more generating capacity than its power utility Eskom can itself build in time, South Africa will in four to five years face a severe shortage of power. 1 ref., 5 figs., 2 tabs.

  12. Carbonization heat of coking coals

    Energy Technology Data Exchange (ETDEWEB)

    H. Ueda; V. Zymla; F. Honnart [Nippon Steel (Japan)

    2005-07-01

    The heat of carbonization is an important element of the coke oven heat balance. It is therefore important to know its absolute value or, at least, its relative variation when coal properties and process parameters change, in order for it to be taken into account by automatic heating control systems. An experimental procedure was thus developed, enabling the heat flow over the whole carbonization temperature range (25-1100{sup o}C) to be measured by DTA. Five coals of different ranks (from 18 to 34% volatile matter) were tested. Results show that all of them exhibit similar behaviour: an endothermic effect below 500{sup o}C and an exothermic effect at higher temperatures. It was established that the heat of carbonization varies with coal rank. The highest exothermic peak was measured for medium volatile hard coking coal. Having ascertained the right measurement procedure, the influence of coal weathering and plastic addition to coal blends on carbonisation heat were studied as well. It was found that the weight loss of oxidized coals during a heating in nitrogen was reduced (coke yield increased) and the heat of carbonization dramatically decreased, especially for medium and high volatile coals. The copyrolysis of coals and plastics (PE, PP, PS, PET) showed also a notable decrease of exothermic heat of carbonization, even for relatively low percentage plastic addition (less then 2%). 6 refs., 5 figs.

  13. Coal, energy and environment: Proceedings

    International Nuclear Information System (INIS)

    Mead, J.S.; Hawse, M.L.

    1994-01-01

    This international conference held in Czechoslovakia was a bold attempt to establish working relationships among scientists and engineers from three world areas: Taiwan, the United States of America, and Czechoslovakia. The magic words unifying this gathering were ''clean coal utilization.'' For the ten nationalities represented, the common elements were the clean use of coal as a domestic fuel and as a source of carbon, the efficient and clean use of coal in power generation, and other uses of coal in environmentally acceptable processes. These three world areas have serious environmental problems, differing in extent and nature, but sufficiently close to create a working community for discussions. Beyond this, Czechoslovakia is emerging from the isolation imposed by control from Moscow. The need for each of these nations to meet and know one another was imperative. The environmental problems in Czechoslovakia are extensive and deep-seated. These proceedings contain 63 papers grouped into the following sections: The research university and its relationship with accrediting associations, government and private industry; Recent advances in coal utilization research; New methods of mining and reclamation; Coal-derived waste disposal and utilization; New applications of coal and environmental technologies; Mineral and trace elements in coal; Human and environmental impacts of coal production and utilization in the Silesian/Moravian region; and The interrelationships between fossil energy use and environmental objectives. Most papers have been processed separately for inclusion on the data base

  14. Methane emissions from coal mining

    International Nuclear Information System (INIS)

    Boyer, C.M.; Kelafant, J.R.; Kuuskraa, V.A.; Manger, K.C.; Kruger, D.

    1990-09-01

    The report estimates global methane emissions from coal mining on a country specific basis, evaluates the technologies available to degasify coal seams and assesses the economics of recovering methane liberated during mining. 33 to 64 million tonnes were liberated in 1987 from coal mining, 75 per cent of which came from China, the USSR, Poland and the USA. Methane emissions from coal mining are likely to increase. Emission levels vary between surface and underground mines. The methane currently removed from underground mines for safety reasons could be used in a number of ways, which may be economically attractive. 55 refs., 19 figs., 24 tabs

  15. Delayed polishing technique on glass–ionomer restorations

    Directory of Open Access Journals (Sweden)

    Masao Irie

    2009-05-01

    Full Text Available This in vitro study evaluated the effect of polishing after 1-day storage in water on the gap-formation around a Class V and Class I restorations, using a resin-modified glass–ionomer and a conventional glass–ionomer materials. The study also examined the gap-formation in another two different cervical restorations, a cervical cavity: incisally bordered by enamel and cervically by dentin and a root surface cavity of these restorative materials, which may be effects of this polishing procedure. This study evaluated the effects of delayed versus immediate polishing to permit maturation on: (1 interfacial gap-formation around resin-modified (RMGIC and conventional (CGIC in three types of cervical restorations, (2 interfacial gap-formation around highly viscous conventional glass–ionomer cement (HCGIC in Class I restorations. After polishing procedure, either: (i immediately (3 or 6 min after setting or (ii after 24 h storage, the maximum the restored teeth were sectioned in a mesio-distal direction through the center of the restorations. The presence or absence of interfacial-gaps was measured at 14 points (each 0.5-mm apart along the cavity restoration interface. For various restorative cases, significant differences (p < 0.05 in gap-width or gap-incidence, were observed between polishing (i immediately and (ii after 1-day storage.

  16. Nail polish as a source of exposure to triphenyl phosphate.

    Science.gov (United States)

    Mendelsohn, Emma; Hagopian, Audrey; Hoffman, Kate; Butt, Craig M; Lorenzo, Amelia; Congleton, Johanna; Webster, Thomas F; Stapleton, Heather M

    2016-01-01

    Triphenyl phosphate (TPHP) is primarily used as either a flame retardant or plasticizer, and is listed as an ingredient in nail polishes. However, the concentration of TPHP in nail polish and the extent of human exposure following applications have not been previously studied. We measured TPHP in ten different nail polish samples purchased from department stores and pharmacies in 2013-2014. Concentrations up to 1.68% TPHP by weight were detected in eight samples, including two that did not list TPHP as an ingredient. Two cohorts (n=26 participants) were recruited to assess fingernail painting as a pathway of TPHP exposure. Participants provided urine samples before and after applying one brand of polish containing 0.97% TPHP by weight. Diphenyl phosphate (DPHP), a TPHP metabolite, was then measured in urine samples (n=411) and found to increase nearly seven-fold 10-14h after fingernail painting (pexposure, ten participants also painted their nails and painted synthetic nails adhered to gloves on two separate occasions, and collected urine for 24h following applications. Urinary DPHP was significantly diminished when wearing gloves, suggesting that the primary exposure route is dermal. Our results indicate that nail polish may be a significant source of short-term TPHP exposure and a source of chronic exposure for frequent users or those occupationally exposed. Copyright © 2015 Elsevier Ltd. All rights reserved.

  17. Hydrotreating of coal-derived liquids

    Energy Technology Data Exchange (ETDEWEB)

    Lott, S.E.; Stohl, F.V.; Diegert, K.V. [Sandia National Lab., Albuquerque, NM (United States)] [and others

    1995-12-31

    To develop a database relating hydrotreating parameters to feed and product quality by experimentally evaluating options for hydrotreating whole coal liquids, distillate cuts of coal liquids, petroleum, and blends of coal liquids with petroleum.

  18. Coal Mining-Related Respiratory Diseases

    Science.gov (United States)

    ... Topics Publications and Products Programs Contact NIOSH NIOSH COAL WORKERS' HEALTH SURVEILLANCE PROGRAM Recommend on Facebook Tweet Share Compartir Coal Mining-Related Respiratory Diseases Coal mining-related respiratory ...

  19. Southern Coal Corporation Clean Water Settlement

    Science.gov (United States)

    Southern Coal Corporation is a coal mining and processing company headquartered in Roanoke, VA. Southern Coal Corporation and the following 26 affiliated entities are located in Alabama, Kentucky, Tennessee, Virginia and West Virginia

  20. Firing a sub-bituminous coal in pulverized coal boilers configured for bituminous coals

    Energy Technology Data Exchange (ETDEWEB)

    N. Spitz; R. Saveliev; M. Perelman; E. Korytni; B. Chudnovsky; A. Talanker; E. Bar-Ziv [Ben-Gurion University of the Negev, Beer-Sheva (Israel)

    2008-07-15

    It is important to adapt utility boilers to sub-bituminous coals to take advantage of their environmental benefits while limiting operation risks. We discuss the performance impact that Adaro, an Indonesian sub-bituminous coal with high moisture content, has on opposite-wall and tangentially-fired utility boilers which were designed for bituminous coals. Numerical simulations were made with GLACIER, a computational-fluid-dynamic code, to depict combustion behavior. The predictions were verified with full-scale test results. For analysis of the operational parameters for firing Adaro coal in both boilers, we used EXPERT system, an on-line supervision system developed by Israel Electric Corporation. It was concluded that firing Adaro coal, compared to a typical bituminous coal, lowers NOx and SO{sub 2} emissions, lowers LOI content and improves fouling behavior but can cause load limitation which impacts flexible operation. 21 refs., 7 figs., 3 tabs.

  1. Too Much Coal, Too Little Oil

    OpenAIRE

    Frederick van der Ploeg; Cees Withagen

    2011-01-01

    Optimal climate policy is studied. Coal, the abundant resource, contributes more CO2 per unit of energy than the exhaustible resource, oil. We characterize the optimal sequencing oil and coal and departures from the Herfindahl rule. "Preference reversal" can take place. If coal is very dirty compared to oil, there is no simultaneous use. Else, the optimal outcome starts with oil, before using oil and coal together, and finally coal on its own, The "laissez-faire" outcome uses coal forever or ...

  2. Flotation and flocculation chemistry of coal and oxidized coals

    Energy Technology Data Exchange (ETDEWEB)

    Somasundaran, P.; Ramesh, R.

    1989-01-01

    This project is designed to develop an understanding of the fundamentals involved in flotation and flocculation of coal, and of coal in various states of oxidation. The main objective of this study is to accurately characterize the coal surface and elucidate mechanisms by which surface interactions between coal and various reagents enhance beneficiation of coals. Effects of oxidation on the modification of surface characteristics of coal by various reagents will also be studied. This quarter, the following studies were conducted in order to further develop our understanding of the role of heterogeneity in interfacial phenomena. (1) Since surface characterization is an important aspect in this project, ESCA (Electron Spectroscopy for Chemical Analysis) study of the coal surface was conducted. Surface derivatization, a technique often used in the preparation of organic compounds for gas-liquid chromatography, uses site specific molecular tags'' that bond to key chemical groups on the surface. Application of derivatization in conjunction with ESCA is a relatively new technique for quantifying functional groups on the surface which has not been possible till now. (2) A distribution of contact angles on the surface of coal (pseudo theta map) is presented based on our earlier results and other published information. The role of heterogeneity in contact angle studies is also examined. 14 refs., 2 tabs.

  3. Scrubbing King Coal's dirty face : a new gasification project southeast of Edmonton hopes to make coal cleaner now and for future generations

    Energy Technology Data Exchange (ETDEWEB)

    Collison, M.

    2008-01-15

    This article described the proposed Dodds-Roundhill Coal Gasification Project. This first commercial coal gasification plant in Canada will be developed by Edmonton-based Sherritt International Corporation, in a 50/50 partnership with the Ontario Teachers' Pension Plan. The project will include a surface coal mine and a coal gasification facility located approximately 80 km southeast of Edmonton, Alberta. Coal gasification is emerging as a clean alternative for converting coal into energy products. It involves the gasification process which breaks down coal to produce hydrogen, carbon monoxide and carbon dioxide, collectively known as synthesis gas (syngas). The syngas can then be used for fuel, as a petrochemical feedstock, or it can be further processed into hydrogen for use by bitumen upgraders and crude oil refineries in Alberta. Carbon dioxide, which is highly concentrated are relatively easy to capture will be either sequestered or used in enhanced oil recovery. Construction will begin in mid-2009 following project application and an environmental impact assessment. 3 figs.

  4. Purification of raw anthracene from black coal tar by crystallization with n-methyl-epsilon-caprolactam

    Energy Technology Data Exchange (ETDEWEB)

    Polaczek, J.; Tecza, T.; Szen, A.; Lisicki, Z.

    1988-07-01

    Compares the performance of NMC (n-methyl-epsilon-caprolactam) and NMP (n-methyl pyrrolidone) as solvents for extracting pure anthracene from crude black coal tar anthracene. Industrial crude anthracene contained 40% anthracene, 13% carbazole, 10% phenanthrene, 3% fluorene and other compounds. Results of laboratory solvent extraction experiments with NMC and NMP are provided, showing the efficient performance of NMC. Extracted anthracene by crystallization had 96% purity. Tables and graphs show crystallization yield and chemical composition of purified anthracene. It is therefore proposed to use NMC solvent for anthracene purification on an industrial scale. A patent application has been submitted under Polish patent nr. P-283250 (1986). 13 refs.

  5. Assessment of the potential for exploitation of the remaining reserves of coal in Poland

    International Nuclear Information System (INIS)

    Wodarski, K.; Bijanska, J.

    2014-01-01

    In mining areas belonging to the Polish mining companies, there is a significant amount of coal, contained in remaining reserves, that have not been exploited so far. For years, the mines have been evaluating the possibility of its exploitation, since it would expand its resource base and would extend its useful life. In addition, exploitation of the remaining reserves can minimize stress concentration zones in the soil, the rebel y improving conditions for maintenance of excavations and limiting the risk of shock rock. (Author)

  6. [Polish medical ethics in the period 1945-1980].

    Science.gov (United States)

    Wichrowski, Marek

    2003-01-01

    The purpose of this article is o present that main currents of Polish medical ethics in the years 1945-1980, which the author treats as the 'prehistory' of Poland's contemporary bioethics. The author begins by ascertaining the post-war disappearance of two Polish traditions--that of the Warsaw school of philosopher-physicians (known in the West as the Polish School of Philosophy of Medicine) and the Lwów-Warsaw School of Philosophy. The political system that come into being after 1945 was not conducive to the development of medical ethics, but several clear orientations may be discerned in the utterances of physicians, lawyers, moral technologlans and academic philosophers. The analysis begins with Catholic ethics in its archaic 1950s-vintage form. The author then presents the thinking of ethicians Independent of both the Church and Marxism (the milieu of the journal 'Etyka') as well as the deontological writings of physicians.

  7. Body conformation comparison of Czech and Polish Hucul horses

    Directory of Open Access Journals (Sweden)

    Zita Matoušová Malbohanová

    2004-01-01

    Full Text Available Measurements of 17 body measures and 11 indices of body conformation on 209 breeding individuals of the Hucul horse were used to analyse the effect of country of origin (Poland and the Czech Republic, sex (stallions and mares, age (5 classes and sire line (Gurgul, Goral, Oušor, Hroby, Polan, Pietrosu, Prislop. All horses were measured by one person. Measures and indexes were analysed by the GLM procedure. The main effect was the country of origin. Highly significant differences were found between both Polish and Czech horses in two thirds of measurements and in more than half of indices. The Czech Hucul horses are significantly higher, longer, wider in pelvis and have longer head than Polish horses. On the contrary to the Czech horses are Polish horses more compact, massive and have deeper chest. Their cannon bone in relation to height of wither is wider.

  8. Human Factors in Nuclear Power Engineering in Polish Conditions

    Directory of Open Access Journals (Sweden)

    Agnieszka Kaczmarek-Kacprzak

    2014-09-01

    Full Text Available The paper “Human factors in nuclear power engineering in Polish conditions” focuses on analysis of dynamics of preparing Polish society to build fi rst nuclear power plant in XXI century in Poland. Authors compare experience from constructing nuclear power plant Sizewell B (Great Britain and Sizewell C, which is in preparation phase with polish nuclear power program. Paper includes aspects e.g. of creating nuclear safety culture and social opinion about investment. Human factors in nuclear power engineering are as well important as relevant economical and technical factors, but very often negligible. In Poland where history about Czarnobyl is still alive, and social opinion is created on emotions after accident in Fukushima, human factors are crucial and should be under comprehensive consideration.

  9. The social shaping of innovation in polish companies

    DEFF Research Database (Denmark)

    Lorentzen, Anne

    2003-01-01

    The paper deals with strategies of innovation in Polish manufacturing companies. The point of departure is a theoretical framework of enterprise level innovation, and of the factors forming strategies of innovation on enterprise level. The paper analyses evidence from 23 Polish companies...... and presents two cases more in detail. The analysis shows that the Polish companies have all been quite innovative, mostly in relation to product innovation. They choose innovation strategies, which are incremental more than radical, and they tend to differentiate their product range rather than to specialise....... They consider quality development a must in the fight for market shares and they adapt equipment and organisation to this goal. The factors forming and determining the strategies of the companies count the technological knowledge and expertise of the owner/founder, the structural changes of the market...

  10. CoalVal-A coal resource valuation program

    Science.gov (United States)

    Rohrbacher, Timothy J.; McIntosh, Gary E.

    2010-01-01

    CoalVal is a menu-driven Windows program that produces cost-of-mining analyses of mine-modeled coal resources. Geological modeling of the coal beds and some degree of mine planning, from basic prefeasibility to advanced, must already have been performed before this program can be used. United States Geological Survey mine planning is done from a very basic, prefeasibility standpoint, but the accuracy of CoalVal's output is a reflection of the accuracy of the data entered, both for mine costs and mine planning. The mining cost analysis is done by using mine cost models designed for the commonly employed, surface and underground mining methods utilized in the United States. CoalVal requires a Microsoft Windows? 98 or Windows? XP operating system and a minimum of 1 gigabyte of random access memory to perform operations. It will not operate on Microsoft Vista?, Windows? 7, or Macintosh? operating systems. The program will summarize the evaluation of an unlimited number of coal seams, haulage zones, tax entities, or other area delineations for a given coal property, coalfield, or basin. When the reader opens the CoalVal publication from the USGS website, options are provided to download the CoalVal publication manual and the CoalVal Program. The CoalVal report is divided into five specific areas relevant to the development and use of the CoalVal program: 1. Introduction to CoalVal Assumptions and Concepts. 2. Mine Model Assumption Details (appendix A). 3. CoalVal Project Tutorial (appendix B). 4. Program Description (appendix C). 5. Mine Model and Discounted Cash Flow Formulas (appendix D). The tutorial explains how to enter coal resource and quality data by mining method; program default values for production, operating, and cost variables; and ones own operating and cost variables into the program. Generated summary reports list the volume of resource in short tons available for mining, recoverable short tons by mining method; the seam or property being mined

  11. Determination of inorganic elements in coal and coal combustion products

    Energy Technology Data Exchange (ETDEWEB)

    Koklu, U.; Akman, S.; Ruppert, L.F. [Istanbul Technical University, Istanbul (Turkey)

    1994-12-31

    Many different methods are applicable to the analysis of inorganic elements in coal and other geological materials. There are only a few elements, namely Cl, F, and P, that are still routinely determined by chemical methods; the majority of elements are determined by instrumental methods. The instrumental techniques commonly employed by coal analysts which will be briefly reviewed here include: instrumental neutron activation analysis (INAA), atomic emission spectroscopy (AES), atomic absorption spectroscopy (AAS), mass spectroscopy (MS), electron microscopy, and X-ray fluorescence (XRF). All of these methods, with the possible exception of electron microscopy, offer rapid and accurate multielement results for the bulk analyses of coal and coal products. There is no single method that can be used to determine all of the elements found in coal. However, nowadays AAS may be the most commonly used instrumental technique. For example, in 1983 about 70% of the geochemical exploration samples collected annually were analyzed with AAS. 105 refs., 1 tab.

  12. [The historical significance of the Polish medical faculty in Edinburgh].

    Science.gov (United States)

    Nowak, K

    1999-01-01

    The Polish Medical Faculty at the University of Edinburgh was a unique phenomenon in the history of universities. Established during the Second World War in 1941 as an entirely autonomous Polish academic institution, the Faculty trained 228 doctors and awarded 19 PhD degrees during its nine years of formal existence (1941-1949). In reviewing its almost 60-year old history, seen in the context of the involvement of the elite of both the political and academic establishments, the splendour of various celebrations and its graduates devotion in keeping the "Edinburgh experiment" alive, the author makes a case for the long-term historical and psychological significance of events well outlasting the period of formal activity of the Faculty. The history of the Faculty is well documented, but the long term outcome in terms of its lasting historical importance is gradually emerging with the passage of time. It has become an indisputable testimony to the generosity and hospitality of the Scottish (political and) academic establishment and a lasting proof of the special liaison between the Scots and the Poles. The Faculty's importance and psychological significance to the rich historical heritage of Polish medicine and the notion of patriotism and loyalty to Polishness have become apparent in the ensuing decades of its carefully maintained tradition. The existence of the Polish Medical Faculty has become an extraordinary asset in the history of Scottish universities, but for the Polish tradition both in Poland and throughout its rich diaspora it constitutes an increasingly valuable historical event which deserves to be cultivated and passed on to younger generations so that it may continue bringing further dividends, so important to national identity, achievement, dignity and pride.

  13. Verbalization the Concept of Dignity in Polish Dictionaries

    Directory of Open Access Journals (Sweden)

    Chaban Vasylyna

    2016-12-01

    Full Text Available Background: The object of the study is the concept of DIGNITY. The justification of the research is predetermined by the lack of such investigation in Polish linguistics. The background for the article is also determined by the lack of similar studies in the sphere of Cognitive Linguistics. Purpose: The article aims at analysing the cultural concept of DIGNITY in the minds of the bearers of the Polish language and culture based on the data incorporated from the lexicographical sources and collection of folk sayings and proverbs. Results: The article dwells upon the most important features of this concept in the Polish language and culture. The study investigates the language conceptualization of this concept in the system of the Polish language and folk maxims and sayings. The definition of the lexeme of dignity reveals the compliance with higher moral principles and the understanding of value; good name, good character claiming attention and respect; the last name. DIGNITY is the principal regulating mechanism of behaviour and development of positive human values which become apparent in the process of human interaction. A man of worth respects himself and is as well proud to be an honourable man. DIGNITY concerns both a separate human and the society in general; it could be regarded as both individual and collective notion. Discussion: The suggested analysis revealed cultural and linguistic peculiarities of the concept of DIGNITY in the Polish language and culture. The conducted research is not exhaustive since it provides potential perspectives for further research of the Polish concept of DIGNITY, in particular, in terms of comparative studies with correlative concepts in Ukrainian and English languages and cultures with the help of the cognitive definition method.

  14. Laser polishing of 3D printed mesoscale components

    Science.gov (United States)

    Bhaduri, Debajyoti; Penchev, Pavel; Batal, Afif; Dimov, Stefan; Soo, Sein Leung; Sten, Stella; Harrysson, Urban; Zhang, Zhenxue; Dong, Hanshan

    2017-05-01

    Laser polishing of various engineered materials such as glass, silica, steel, nickel and titanium alloys, has attracted considerable interest in the last 20 years due to its superior flexibility, operating speed and capability for localised surface treatment compared to conventional mechanical based methods. The paper initially reports results from process optimisation experiments aimed at investigating the influence of laser fluence and pulse overlap parameters on resulting workpiece surface roughness following laser polishing of planar 3D printed stainless steel (SS316L) specimens. A maximum reduction in roughness of over 94% (from ∼3.8 to ∼0.2 μm Sa) was achieved at the optimised settings (fluence of 9 J/cm2 and overlap factors of 95% and 88-91% along beam scanning and step-over directions respectively). Subsequent analysis using both X-ray photoelectron spectroscopy (XPS) and glow discharge optical emission spectroscopy (GDOES) confirmed the presence of surface oxide layers (predominantly consisting of Fe and Cr phases) up to a depth of ∼0.5 μm when laser polishing was performed under normal atmospheric conditions. Conversely, formation of oxide layers was negligible when operating in an inert argon gas environment. The microhardness of the polished specimens was primarily influenced by the input thermal energy, with greater sub-surface hardness (up to ∼60%) recorded in the samples processed with higher energy density. Additionally, all of the polished surfaces were free of the scratch marks, pits, holes, lumps and irregularities that were prevalent on the as-received stainless steel samples. The optimised laser polishing technology was consequently implemented for serial finishing of structured 3D printed mesoscale SS316L components. This led to substantial reductions in areal Sa and St parameters by 75% (0.489-0.126 μm) and 90% (17.71-1.21 μm) respectively, without compromising the geometrical accuracy of the native 3D printed samples.

  15. COAL SLAGGING AND REACTIVITY TESTING

    Energy Technology Data Exchange (ETDEWEB)

    Donald P. McCollor; Kurt E. Eylands; Jason D. Laumb

    2003-10-01

    Union Fenosa's La Robla I Power Station is a 270-MW Foster Wheeler arch-fired system. The unit is located at the mine that provides a portion of the semianthracitic coal. The remaining coals used are from South Africa, Russia, Australia, and China. The challenges at the La Robla I Station stem from the various fuels used, the characteristics of which differ from the design coal. The University of North Dakota Energy & Environmental Research Center (EERC) and the Lehigh University Energy Research Center (LUERC) undertook a program to assess problematic slagging and unburned carbon issues occurring at the plant. Full-scale combustion tests were performed under baseline conditions, with elevated oxygen level and with redistribution of air during a site visit at the plant. During these tests, operating information, observations and temperature measurements, and coal, slag deposit, and fly ash samples were obtained to assess slagging and unburned carbon. The slagging in almost all cases appeared due to elevated temperatures rather than fuel chemistry. The most severe slagging occurred when the temperature at the sampling port was in excess of 1500 C, with problematic slagging where first-observed temperatures exceeded 1350 C. The presence of anorthite crystals in the bulk of the deposits analyzed indicates that the temperatures were in excess of 1350 C, consistent with temperature measurements during the sampling period. Elevated temperatures and ''hot spots'' are probably the result of poor mill performance, and a poor distribution of the coal from the mills to the specific burners causes elevated temperatures in the regions where the slag samples were extracted. A contributing cause appeared to be poor combustion air mixing and heating, resulting in oxygen stratification and increased temperatures in certain areas. Air preheater plugging was observed and reduces the temperature of the air in the windbox, which leads to poor combustion

  16. Stratified Sampling to Define Levels of Petrographic Variation in Coal Beds: Examples from Indonesia and New Zealand

    Directory of Open Access Journals (Sweden)

    Tim A. Moore

    2016-01-01

    Full Text Available DOI: 10.17014/ijog.3.1.29-51Stratified sampling of coal seams for petrographic analysis using block samples is a viable alternative to standard methods of channel sampling and particulate pellet mounts. Although petrographic analysis of particulate pellets is employed widely, it is both time consuming and does not allow variation within sampling units to be assessed - an important measure in any study whether it be for paleoenvironmental reconstruction or in obtaining estimates of industrial attributes. Also, samples taken as intact blocks provide additional information, such as texture and botanical affinity that cannot be gained using particulate pellets. Stratified sampling can be employed both on ‘fine’ and ‘coarse’ grained coal units. Fine-grained coals are defined as those coal intervals that do not contain vitrain bands greater than approximately 1 mm in thickness (as measured perpendicular to bedding. In fine-grained coal seams, a reasonable sized block sample (with a polished surface area of ~3 cm2 can be taken that encapsulates the macroscopic variability. However, for coarse-grained coals (vitrain bands >1 mm a different system has to be employed in order to accurately account for the larger particles. Macroscopic point counting of vitrain bands can accurately account for those particles>1 mm within a coal interval. This point counting method is conducted using something as simple as string on a coal face with marked intervals greater than the largest particle expected to be encountered (although new technologies are being developed to capture this type of information digitally. Comparative analyses of particulate pellets and blocks on the same interval show less than 6% variation between the two sample types when blocks are recalculated to include macroscopic counts of vitrain. Therefore even in coarse-grained coals, stratified sampling can be used effectively and representatively.

  17. Steam jacket dynamics in underground coal gasification

    Science.gov (United States)

    Otto, Christopher; Kempka, Thomas

    2017-04-01

    Underground coal gasification (UCG) has the potential to increase the world-wide hydrocarbon reserves by utilization of deposits not economically mineable by conventional methods. In this context, UCG involves combusting coal in-situ to produce a high-calorific synthesis gas, which can be applied for electricity generation or chemical feedstock production. Apart from high economic potentials, in-situ combustion may cause environmental impacts such as groundwater pollution by by-product leakage. In order to prevent or significantly mitigate these potential environmental concerns, UCG reactors are generally operated below hydrostatic pressure to limit the outflow of UCG process fluids into overburden aquifers. This pressure difference effects groundwater inflow into the reactor and prevents the escape of product gas. In the close reactor vicinity, fluid flow determined by the evolving high reactor temperatures, resulting in the build-up of a steam jacket. Numerical modeling is one of the key components to study coupled processes in in-situ combustion. We employed the thermo-hydraulic numerical simulator MUFITS (BINMIXT module) to address the influence of reactor pressure dynamics as well as hydro-geological coal and caprock parameters on water inflow and steam jacket dynamics. The US field trials Hanna and Hoe Creek (Wyoming) were applied for 3D model validation in terms of water inflow matching, whereby the good agreement between our modeling results and the field data indicates that our model reflects the hydrothermal physics of the process. In summary, our validated model allows a fast prediction of the steam jacket dynamics as well as water in- and outflows, required to avoid aquifer contamination during the entire life cycle of in-situ combustion operations.

  18. Evolution of polish E-commerce - main trends and perspectives

    OpenAIRE

    Chodak, Grzegorz

    2008-01-01

    The aim of this paper is to present main phases of Polish e-commerce development and to show its major trends. The author also tries to predict future directions of its development. The whole e-commerce process of development is divided into five phases. The first part of the paper presents the beginnings of Polish e-commerce. Then the following stages of development are discussed with presentation of some key figures e.g. percentage of individuals who ordered goods or services over the Inter...

  19. Polish as a Foreign Language: New Context, Regulations and Prospects

    Directory of Open Access Journals (Sweden)

    Popławska Anna

    2015-10-01

    Full Text Available The article provides an overview of the developments in Poland after the collapse of communism in 1989 from the point of view of foreign language teaching, including a swift reorientation and transition from a public school system with Russian as the main foreign language, to a diversified language teaching market focused on teaching English and other languages. A particular stress is placed on a relatively new phenomenon, being an increased demand and new opportunities for teaching Polish as a foreign language to be further promoted as a result of anticipated amendments to legal regulations governing the status and certification of the Polish language.

  20. Laser polishing for topography management of accelerator cavity surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Liang [College of William and Mary, Williamsburg, VA (United States); Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Klopf, J. Mike [College of William and Mary, Williamsburg, VA (United States); Reece, Charles E. [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Kelley, Michael J. [College of William and Mary, Williamsburg, VA (United States); Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States)

    2015-07-20

    Improved energy efficiency and reduced cost are greatly desired for advanced particle accelerators. Progress toward both can be made by atomically-smoothing the interior surface of the niobium superconducting radiofrequency accelerator cavities at the machine's heart. Laser polishing offers a green alternative to the present aggressive chemical processes. We found parameters suitable for polishing niobium in all surface states expected for cavity production. As a result, careful measurement of the resulting surface chemistry revealed a modest thinning of the surface oxide layer, but no contamination.