WorldWideScience

Sample records for polished fused silica

  1. CO/sub 2/-laser polishing of fused silica surfaces for increased laser damage resistance at 1. 06. mu. m

    Energy Technology Data Exchange (ETDEWEB)

    Temple, P.A.; Milam, D.; Lowdermilk, W.H.

    1980-04-03

    Bare fused silica surfaces were prepared by subjecting the mechanically polished surface to a rastered cw CO/sub 2/ laser beam. Analysis shows that this processing causes: (a) removal of a uniform layer of fused silica; and (b) a probable re-fusing or healing of existing subsurface fractures. The fused silica removal rate is found to be a function of the laser intensity and scan rate. These surfaces are seen to have very low scatter and to be very smooth. In addition, they have exhibited entrance surface damage thresholds at 1.06 ..mu..m, and 1 nsec, which are substantially above those seen on the mechanically polished surface. When damage does occur, it tends to be at a few isolated points rather than the general uniform damage seen on the mechanicaly polished part. In addition to the damage results, we will discuss an observational technique used for viewing these surfaces which employs dark-field illumination.

  2. Correlation of polishing-induced shallow subsurface damages with laser-induced gray haze damages in fused silica optics

    Science.gov (United States)

    He, Xiang; Zhao, Heng; Wang, Gang; Zhou, Peifan; Ma, Ping

    2016-08-01

    Laser-induced damage in fused silica optics greatly restricts the performances of laser facilities. Gray haze damage, which is always initiated on ceria polished optics, is one of the most important damage morphologies in fused silica optics. In this paper, the laser-induced gray haze damages of four fused silica samples polished with CeO2, Al2O3, ZrO2, and colloidal silica slurries are investigated. Four samples all present gray haze damages with much different damage densities. Then, the polishing-induced contaminant and subsurface damages in four samples are analyzed. The results reveal that the gray haze damages could be initiated on the samples without Ce contaminant and are inclined to show a tight correlation with the shallow subsurface damages.

  3. Material removal and surface figure during pad polishing of fused silica

    Energy Technology Data Exchange (ETDEWEB)

    Suratwala, T I; Feit, M D; Steele, W A

    2009-05-04

    The material removal and surface figure after ceria pad polishing of fused silica glass have been measured and analyzed as a function of kinematics, loading conditions, and polishing time. Also, the friction at the workpiece/lap interface, the slope of the workpiece relative to the lap plane, and lap viscoelastic properties have been measured and correlated to material removal. The results show that the relative velocity between the workpiece & lap (determined by the kinematics) and the pressure distribution determine the spatial and temporal material removal and hence the final surface figure of the workpiece. In the case where the applied loading and relative velocity distribution over the workpiece are spatially uniform, a significant non-uniform spatial material removal from the workpiece surface is observed. This is due to a non-uniform pressure distribution resulting from: (1) a moment caused by a pivot point and interface friction forces; (2) viscoelastic relaxation of the polyurethane lap; and (3) a physical workpiece/lap interface mismatch. Both the kinematics and these contributions to the pressure distribution are quantitatively described, and then combined to form a spatial and temporal Preston model & code for material removal (called Surface Figure or SurF{copyright}). The surface figure simulations are consistent with the experiment for a wide variety of polishing conditions. This study is an important step towards deterministic full-aperture polishing, which would allow optical glass fabrication to be performed in a more repeatable, less iterative, and hence more economical manner.

  4. Surface analysis of polished fused-silica laser lenses by ion-scattering spectrometry

    International Nuclear Information System (INIS)

    Orvek, K.; Steward, S.A.

    1982-01-01

    New advances in high-powered glass lasers, particularly the NOVA system, have resulted in a need for lenses having higher damage threshold values than those now available. It is currently thought that surface contaminants on the lenses are responsible for initiating part of the damage. These contaminants are apparently introduced during the final polishing stages. In this study, we used ion-scattering spectrometry (ISS) to identify contaminants arising through the use of different polishing techniques. Five lenses were studied, each having undergone different polishing procedures. The first lens was not polished after receiving it from the manfacturer (No. 381). Ion microprobe data were available for this lens, and they were compared to ISS results. The second lens had been polished with rouge, a polishing compound no longer in use (No. 796). This sample served as a further check on the ISS results. The third lens was studied as received from the manufacturer - with no handling or cleaning (No. 802). The final two lenses had both been polished using high-purity ceria, cerium oxide (No. 800 and No. 801). The difference between these two was that No. 800 was polished using a nylon lap, and No. 801 was polished using pitch as a lap. The 800-series lenses were all made from the same batch, and constituted the major part of the investigation

  5. Fluorine-Based DRIE of Fused Silica

    Science.gov (United States)

    Yee, Karl; Shcheglov, Kirill; Li, Jian; Choi, Daniel

    2007-01-01

    A process of deep reactive-ion etching (DRIE) using a fluorine-based gas mixture enhanced by induction-coupled plasma (ICP) has been demonstrated to be effective in forming high-aspect-ratio three-dimensional patterns in fused silica. The patterns are defined in part by an etch mask in the form of a thick, high-quality aluminum film. The process was developed to satisfy a need to fabricate high-aspect-ratio fused-silica resonators for vibratory microgyroscopes, and could be used to satisfy similar requirements for fabricating other fused-silica components.

  6. Fused Silica and Other Transparent Window Materials

    Science.gov (United States)

    Salem, Jon

    2016-01-01

    Several transparent ceramics, such as spinel and AlONs are now being produced in sufficient large areas to be used in space craft window applications. The work horse transparent material for space missions from Apollo to the International Space Station has been fused silica due in part to its low coefficient of expansion and optical quality. Despite its successful use, fused silica exhibits anomalies in its crack growth behavior, depending on environmental preconditioning and surface damage. This presentation will compare recent optical ceramics to fused silica and discuss sources of variation in slow crack growth behavior.

  7. Radiation hardness study on fused silica

    NARCIS (Netherlands)

    Hoek, M.; Bennet, E. D.; Branford, D.; Cowie, E. N.; Dueren, M.; Foehl, K.; Glazier, D.; Kaiser, R.; Lehmann, A.; Lu, S.; Marton, J.; Ostendorf, R.; Schepers, G.; Schwarz, C.; Seitz, B.; Teufel, A.; Watts, D.

    2008-01-01

    Radiation hardness tests have been carried out on fused silica samples of the highest optical grade from three different manufacturers (Suprasil, Lithosil and Coming). The samples were irradiated with protons in order to emulate the expected accumulated radiation damage over the entire life span of

  8. Quartz/fused silica chip carriers

    Science.gov (United States)

    1992-01-01

    The primary objective of this research and development effort was to develop monolithic microwave integrated circuit (MMIC) packaging which will operate efficiently at millimeter-wave frequencies. The packages incorporated fused silica as the substrate material which was selected due to its favorable electrical properties and potential performance improvement over more conventional materials for Ka-band operation. The first step towards meeting this objective is to develop a package that meets standard mechanical and thermal requirements using fused silica and to be compatible with semiconductor devices operating up to at least 44 GHz. The second step is to modify the package design and add multilayer and multicavity capacity to allow for application specific integrated circuits (ASIC's) to control multiple phase shifters. The final step is to adapt the package design to a phased array module with integral radiating elements. The first task was a continuation of the SBIR Phase 1 work. Phase 1 identified fused silica as a viable substrate material by demonstrating various plating, machining, and adhesion properties. In Phase 2 Task 1, a package was designed and fabricated to validate these findings. Task 2 was to take the next step in packaging and fabricate a multilayer, multichip module (MCM). This package is the predecessor to the phased array module and demonstrates the ability to via fill, circuit print, laminate, and to form vertical interconnects. The final task was to build a phased array module. The radiating elements were to be incorporated into the package instead of connecting to it with wire or ribbon bonds.

  9. Mechanical losses in thin fused silica fibres

    International Nuclear Information System (INIS)

    Bilenko, I A; Braginsky, V B; Lourie, S L

    2004-01-01

    Intracavity topology of the readout system for LIGO III project and table-top QND mechanical measurements under development require the use of small probe masses and suspensions with a very low level of internal losses. A good choice is to use thin fused silica fibres similar to LIGO II mirrors suspensions. Mechanical losses of silica fibres are investigated in this work through the study of quality factor dependence on diameter for pendulum and violin modes of oscillations with diameters ranging from 1.5 to 40 μm. The estimated values of effective mechanical loss angle show noticeably greater growth with lower diameters than might be expected while extrapolating known results of research done for thicker fibres

  10. Mechanical losses in thin fused silica fibres

    Energy Technology Data Exchange (ETDEWEB)

    Bilenko, I A; Braginsky, V B; Lourie, S L [Department of Oscillatory Physics, Physics Faculty, Moscow State University (Russian Federation)

    2004-03-07

    Intracavity topology of the readout system for LIGO III project and table-top QND mechanical measurements under development require the use of small probe masses and suspensions with a very low level of internal losses. A good choice is to use thin fused silica fibres similar to LIGO II mirrors suspensions. Mechanical losses of silica fibres are investigated in this work through the study of quality factor dependence on diameter for pendulum and violin modes of oscillations with diameters ranging from 1.5 to 40 {mu}m. The estimated values of effective mechanical loss angle show noticeably greater growth with lower diameters than might be expected while extrapolating known results of research done for thicker fibres.

  11. Ultraviolet Laser Damage Dependence on Contamination Concentration in Fused Silica Optics during Reactive Ion Etching Process

    Directory of Open Access Journals (Sweden)

    Laixi Sun

    2018-04-01

    Full Text Available The reactive ion etching (RIE process of fused silica is often accompanied by surface contamination, which seriously degrades the ultraviolet laser damage performance of the optics. In this study, we find that the contamination behavior on the fused silica surface is very sensitive to the RIE process which can be significantly optimized by changing the plasma generating conditions such as discharge mode, etchant gas and electrode material. Additionally, an optimized RIE process is proposed to thoroughly remove polishing-introduced contamination and efficiently prevent the introduction of other contamination during the etching process. The research demonstrates the feasibility of improving the damage performance of fused silica optics by using the RIE technique.

  12. Quantification of residual stress from photonic signatures of fused silica

    International Nuclear Information System (INIS)

    Cramer, K. Elliott; Yost, William T.; Hayward, Maurice

    2014-01-01

    A commercially available grey-field polariscope (GFP) instrument for photoelastic examination is used to assess impact damage inflicted upon the outer-most pane of Space Shuttle windows made from fused silica. A method and apparatus for calibration of the stress-optic coefficient using four-point bending is discussed. The results are validated on known material (acrylic) and are found to agree with literature values to within 6%. The calibration procedure is then applied to fused-silica specimens and the stress-optic coefficient is determined to be 2.43 ± 0.54 × 10 −12 Pa −1 . Fused silica specimens containing impacts artificially made at NASA’s Hypervelocity Impact Technology Facility (HIT-F), to simulate damage typical during space flight, are examined. The damage sites are cored from fused silica window carcasses and examined with the GFP. The calibrated GFP measurements of residual stress patterns surrounding the damage sites are presented

  13. Quantification of Residual Stress from Photonic Signatures of Fused Silica

    Science.gov (United States)

    Cramer, K. Elliott; Hayward, Maurice; Yost, William E.

    2013-01-01

    A commercially available grey-field polariscope (GFP) instrument for photoelastic examination is used to assess impact damage inflicted upon the outer-most pane of Space Shuttle windows made from fused silica. A method and apparatus for calibration of the stress-optic coefficient using four-point bending is discussed. The results are validated on known material (acrylic) and are found to agree with literature values to within 6%. The calibration procedure is then applied to fused-silica specimens and the stress-optic coefficient is determined to be 2.43 +/- 0.54 x 10(exp -12)/Pa. Fused silica specimens containing impacts artificially made at NASA's Hypervelocity Impact Technology Facility (HIT-F), to simulate damage typical during space flight, are examined. The damage sites are cored from fused silica window carcasses and examined with the GFP. The calibrated GFP measurements of residual stress patterns surrounding the damage sites are presented. Keywords: Glass, fused silica, photoelasticity, residual stress

  14. Stimulated resonant scattering at stressed fused silica surface

    International Nuclear Information System (INIS)

    Bouchut, Philippe; Reymermier, Maryse

    2015-01-01

    The radiative emission in CO 2 laser heated stressed fused silica is radically modified when gold microspheres are on the surface. At high heating rates, the emission dynamics changes from thermoluminescence to stimulated resonant scattering with an emission rate that is increased tenfold and the near infrared (NIR) spectrum is red-shifted. We show that the dynamic tensile stress that rises in heated silica is coupled with a fluctuating electromagnetic field that enables electromagnetic friction between moving OH emitters from silica bulk and NIR resonant scatterers at the silica surface. (paper)

  15. Wide spectrum antireflective coating for fused silica and other glasses

    Science.gov (United States)

    Yoldas, B. E.; Partlow, D. P.

    1984-05-01

    A method of forming a laser damage resistant wide-spectrum antireflective coating on fused silica and other glasses has been developed. The single-layer graded-index coating is deposited from a specific polymer solution which is converted to a porous SiO2 film. The size of the pores in the film is first reduced by heat treatment to prevent eventual UV scattering. Refractive-index gradation is achieved by grading this nonscattering porosity using a mild etching agent to a depth which is sufficient to smooth the density transition from air to the substrate glass. The resultant coating provides antireflectivity over the entire transmission range of silica extending to wavelengths as short as 250 nm. Laser damage thresholds as high as 9 J/sq cm at 350 nm have been demonstrated for this coating on fused silica substrates, which makes it particularly suitable for the optics of high-power lasers.

  16. Effects of silica-coating on surface topography and bond strength of porcelain fused to CAD/CAM pure titanium.

    Science.gov (United States)

    Fukuyama, Takushi; Hamano, Naho; Ino, Satoshi

    2016-01-01

    The aim of this study was to evaluate the shear bond strength of porcelain fusing to titanium and the effects of surface treatment on surface structure of titanium. In the shear bond strength test, titanium surface treatments were: conventional, silica-coating without bonding agent, and silica-coating with bonding agent. Titanium surface treatments for analysis by the atomic force microscope (AFM) were: polishing, alumina sandblasting and silica-coating. The shear bond strength value of silica-coating with bonding agent group showed significantly higher than that of other groups. In AFM observation results, regular foamy structure which is effective for wetting was only observed in silica-coating. Therefore, this structure might indicate silicon. Silica-coating renders forms a nanoscopic regular foamy structure, involved in superhydrophilicity, to titanium surface, which is markedly different from the irregular surface generated by alumina sandblasting.

  17. Mechanical protection of DLC films on fused silica slides

    Science.gov (United States)

    Nir, D.

    1985-01-01

    Measurements were made with a new test for improved quantitative estimation of the mechanical protection of thin films on optical materials. The mechanical damage was induced by a sand blasting system using spherical glass beads. Development of the surface damage was measured by the changes in the specular transmission and reflection, and by inspection using a surface profilometer and a scanning electron microscope. The changes in the transmittance versus the duration of sand blasting was measured for uncoated fused silica slides and coated ones. It was determined that the diamond like carbon films double the useful optical lifetime of the fused silica. Theoretical expressions were developed to describe the stages in surface deterioration. Conclusions were obtained for the SiO2 surface mechanism and for the film removal mechanism.

  18. Optical Properties of the DIRC Fused Silica Cherenkov Radiator

    Energy Technology Data Exchange (ETDEWEB)

    Schwiening, Jochen

    2003-04-30

    The DIRC is a new type of Cherenkov detector that is successfully operating as the hadronic particle identification system for the BABAR experiment at SLAC. The fused silica bars that serve as the DIRC's Cherenkov radiators must transmit the light over long optical pathlengths with a large number of internal reflections. This imposes a number of stringent and novel requirements on the bar properties. This note summarizes a large amount of R&D that was performed both to develop specifications and production methods and to determine whether commercially produced bars could meet the requirements. One of the major outcomes of this R&D work is an understanding of methods to select radiation hard and optically uniform fused silica material. Others include measurement of the wavelength dependency of the internal reflection coefficient, and its sensitivity to surface contaminants, development of radiator support methods, and selection of good optical glue.

  19. Rate equation model of bulk optical damage of silica, and the influence of polishing on surface optical damage of silica

    Science.gov (United States)

    Smith, Arlee; Do, Binh; Schuster, Rod; Collier, David

    2008-02-01

    Our objective is to understand the mechanism that generates catastrophic optical damage in pulsed fiber amplifiers. We measured optical damage thresholds of bulk fused silica at 1064 nm for 8 ns and 14 ps pulses. The 8 ns pulse is single longitudinal mode from a Q-switched laser, and the 14 ps pulse is from a Q-switched mode-lock laser. The beams in both cases are TEM 00 mode, and they are focused to a 7.5 μm spot inside a fused silica window. The pulse-to-pulse energy variations are 1% for 8 ns pulses and 5% for 14 ps pulses. Under these conditions optical damage is always accompanied by plasma formation at the focal spot; we found the damage threshold fluences are 3854 +/- 85 J/cm2 for the 8 ns pulses and 25.4 +/- 1.0 J/cm2 for the 14 ps pulses. These fluences are corrected for self focusing. Both damage thresholds are deterministic, in contrast to the claim often made in the literature that optical damage is statistical in the nanosecond range. The measured damage threshold fluences for 8 ns and 14 ps pulses do not fit a square root of pulse duration scaling rule. We interpret the damage in terms of plasma formation initiated by multiphoton ionization and amplified by an electron avalanche. The damage threshold irradiance can be matched with a simple rate equation model that includes multiphoton ionization, electron avalanche, and electron-hole recombination. The damage morphologies are dramatically different in the nanosecond and picosecond cases because of the large difference in deposited energy. However, both morphologies are reproducible from pulse to pulse. We also measured surface damage thresholds for silica windows polished by different methods. We find that cerium oxide polished surfaces damage at approximately 40% of the bulk threshold, with a large statistical spread. Surfaces prepared using an Al IIO 3 polish damaged between 50% and 100% of the bulk damage limit, with a substantial fraction at 100%. Surfaces polished using first the Al IIO 3 polish

  20. The mechanism of growth of quartz crystals into fused silica

    Science.gov (United States)

    Fratello, V. J.; Hays, J. F.; Spaepen, F.; Turnbull, D.

    1980-01-01

    It is proposed that the growth of quartz crystals into fused silica is effected by a mechanism involving the breaking of an Si-O bond and its association with an OH group, followed by cooperative motion of the nonbridging oxygen and the hydroxyl group which results in the crystallization of a row of several molecules along a crystalline-amorphous interfacial ledge. This mechanism explains, at least qualitatively, all the results of the earlier experimental study of the dependence of quartz crystal growth upon applied pressure: large negative activation volume; single activation enthalpy below Si-O bond energy; growth velocity constant in time, proportional to the hydroxyl and chlorine content, decreasing with increasing degree of reduction, and enhanced by nonhydrostatic stresses; lower pre-exponential for the synthetic than for the natural silica.

  1. Threats to ICF reactor materials: computational simulations of radiation damage induced topological changes in fused silica

    CERN Document Server

    Kubota, A; Stolken, J; Sadigh, B; Reyes, S; Rubia, T D; Latkowski, J F

    2003-01-01

    We have performed molecular dynamics simulations of radiation damage in fused silica. In this study, we discuss the role of successive cascade overlap on the saturation and self-healing of oxygen vacancy defects in the amorphous fused silica network. Furthermore, we present findings on the topological changes in fused silica due to repeated energetic recoil atoms. These topological network modifications consistent with experimental Raman spectroscopic observation on neutron and ion irradiated fused silica are indicators of permanent densification that has also been observed experimentally.

  2. Laser induced damage and fracture in fused silica vacuum windows

    International Nuclear Information System (INIS)

    Campbell, J.H.; Hurst, P.A.; Heggins, D.D.; Steele, W.A.; Bumpas, S.E.

    1996-11-01

    Laser-induced damage, that initiates catastrophic fracture, has been observed in large (≤61 cm dia) fused silica lenses that also serve as vacuum barriers in Nova and Beamlet lasers. If the elastic stored energy in the lens is high enough, the lens will fracture into many pieces (implosion). Three parameters control the degree of fracture in the vacuum barrier window: elastic stored energy (tensile stress), ratio of window thickness to flaw depth, and secondary crack propagation. Fracture experiments were conducted on 15-cm dia fused silica windows that contain surface flaws caused by laser damage. Results, combined with window failure data on Beamlet and Nova, were used to develop design criteria for a ''fail-safe'' lens (that may catastrophically fracture but not implode). Specifically, the window must be made thick enough so that the peak tensile stress is less than 500 psi (3.4 MPa) and the thickness/critical flaw size is less than 6. The air leak through the window fracture and into the vacuum must be rapid enough to reduce the load on the window before secondary crack growth occurs. Finite element stress calculations of a window before and immediately following fracture into two pieces show that the elastic stored energy is redistributed if the fragments ''lock'' in place and thereby bridge the opening. In such cases, the peak stresses at the flaw site can increase, leading to further (i.e. secondary) crack growth

  3. Thin fused silica shells for high-resolution and large collecting area x-ray telescopes (like Lynx/XRS)

    Science.gov (United States)

    Civitani, M. M.; Hołyszko, J.; Vecchi, G.; Basso, S.; Citterio, O.; Ghigo, M.; Pareschi, G.; Parodi, G.; Incorvaia, S.

    2017-09-01

    The implementation of an X-ray mission with high imaging capabilities, similar to those achieved with Chandra (studied in USA, with the participation of international partners. In order to figure out the challenging technological task of the mirror fabrication, different approaches are considered, based on monolithic and segmented shells. Starting from the experience done on the glass prototypal shell realized in the past years, the direct polishing of thin (2 mm thick) fused silica monolithic shells is being investigated as a possible solution. A temporary stiffening structure is designed to support the shell during the figuring and polishing operations and to manage the handling up to its integration in the telescope structure. After the grinding and the polishing phases, in order to achieve the required surface accuracy, a final ion beam figuring correction is foreseen. In this paper, we present the technological process and the results achieved so far on a prototypal shell under development.

  4. Antireflective sub-wavelength structures on fused silica via self-assembly of silica

    International Nuclear Information System (INIS)

    Du, Ying; Zhu, Meiping; Sui, Zhan; Yi, Kui; Jin, Yunxia; He, Hongbo

    2013-01-01

    Antireflective sub-wavelength structures with high laser-induced damage threshold on fused silica are fabricated using a self-assembly technique, in which a porous yttrium oxide film is deposited as a mask followed by alkaline etching. By controlling the etching time, several sub-wavelength structures with different height, density and diameter have been made. The best reflectance is less than 2.87% for wavelengths from 300 to 1000 nm after 1.5 h etching. The laser-induced damage threshold of the etched glass measured by a 10 ns Nd:YAG laser at a wavelength of 532 nm was as high as 30 J/cm 2 compared to 16 J/cm 2 of blank glass. The specular reflectance of structures matches the theoretical simulation using a thin-film multilayer model, and the results reveal that the shape of the structures is similar to the calculated parabolic shape. Achieving antireflective sub-wavelength structures on fused silica paves the way for applications in laser systems. - Highlights: • Antireflective structures on fused silica are grown using a self-assembly technique. • The properties of structures with different etching time were studied. • The laser-induced damage threshold of glass was enhanced after etching. • The reflection matches the theoretical simulation using a thin-film multilayer model

  5. Optical Properties of the DIRC Fused Silica Radiator

    Energy Technology Data Exchange (ETDEWEB)

    Convery, Mark R

    2003-04-15

    The DIRC detector is successfully operating as the hadronic particle identification system for the BaBar experiment at SLAC. The production of its Cherenkov radiator required much effort in practice, both in manufacture and conception, which in turn required a large number of R&D measurements. One of the major outcomes of this R&D work was an understanding of methods to select radiation hard and optically uniform fused silica material. Others included measurement of the wavelength dependency of the internal reflection coefficient, and its sensitivity to the surface pollution, selection of the radiator support, selection of good optical glue, etc. This note summarizes the optical R&D test results.

  6. The anomalous yield behavior of fused silica glass

    Science.gov (United States)

    Schill, W.; Heyden, S.; Conti, S.; Ortiz, M.

    2018-04-01

    We develop a critical-state model of fused silica plasticity on the basis of data mined from molecular dynamics (MD) calculations. The MD data is suggestive of an irreversible densification transition in volumetric compression resulting in permanent, or plastic, densification upon unloading. The MD data also reveals an evolution towards a critical state of constant volume under pressure-shear deformation. The trend towards constant volume is from above, when the glass is overconsolidated, or from below, when it is underconsolidated. We show that these characteristic behaviors are well-captured by a critical state model of plasticity, where the densification law for glass takes the place of the classical consolidation law of granular media and the locus of constant-volume states defines the critical-state line. A salient feature of the critical-state line of fused silica, as identified from the MD data, that renders its yield behavior anomalous is that it is strongly non-convex, owing to the existence of two well-differentiated phases at low and high pressures. We argue that this strong non-convexity of yield explains the patterning that is observed in molecular dynamics calculations of amorphous solids deforming in shear. We employ an explicit and exact rank-2 envelope construction to upscale the microscopic critical-state model to the macroscale. Remarkably, owing to the equilibrium constraint the resulting effective macroscopic behavior is still characterized by a non-convex critical-state line. Despite this lack of convexity, the effective macroscopic model is stable against microstructure formation and defines well-posed boundary-value problems.

  7. Non-destructive evaluation of UV pulse laser-induced damage performance of fused silica optics.

    Science.gov (United States)

    Huang, Jin; Wang, Fengrui; Liu, Hongjie; Geng, Feng; Jiang, Xiaodong; Sun, Laixi; Ye, Xin; Li, Qingzhi; Wu, Weidong; Zheng, Wanguo; Sun, Dunlu

    2017-11-24

    The surface laser damage performance of fused silica optics is related to the distribution of surface defects. In this study, we used chemical etching assisted by ultrasound and magnetorheological finishing to modify defect distribution in a fused silica surface, resulting in fused silica samples with different laser damage performance. Non-destructive test methods such as UV laser-induced fluorescence imaging and photo-thermal deflection were used to characterize the surface defects that contribute to the absorption of UV laser radiation. Our results indicate that the two methods can quantitatively distinguish differences in the distribution of absorptive defects in fused silica samples subjected to different post-processing steps. The percentage of fluorescence defects and the weak absorption coefficient were strongly related to the damage threshold and damage density of fused silica optics, as confirmed by the correlation curves built from statistical analysis of experimental data. The results show that non-destructive evaluation methods such as laser-induced fluorescence and photo-thermal absorption can be effectively applied to estimate the damage performance of fused silica optics at 351 nm pulse laser radiation. This indirect evaluation method is effective for laser damage performance assessment of fused silica optics prior to utilization.

  8. Influence of Cutting Speed on Subsurface Damage Morphology and Distribution in Ground Fused Silica

    Directory of Open Access Journals (Sweden)

    Georg Schnurbusch

    2017-08-01

    Full Text Available In optical fabrication, brittle-hard materials are used for numerous applications. Especially for high-performance optics for laser or lithography applications, a complex and consistent production chain is necessary to account for the material properties. Particularly in pre-processing, e.g., for shaping optical components, brittle material behavior is dominant which leads to a rough surface layer with cracks that reach far below the surface. This so called subsurface damage (SSD needs to be removed in subsequent processes like polishing. Therefore, it is essential to know the extent of the SSD induced by shaping for an efficient design of precise corrective processes and for process improvement. Within this work the influence of cutting speed on SSD, in fused silica, induced by grinding has been investigated. To analyze the subsurface crack distribution and the maximum crack depth magnetorheological finishing has been appointed to polish a wedge into the ground surface. The depth profile of SSD was analyzed by image processing. For this purpose a coherent area of the polished wedge has been recorded by stitching microscopy. Taking the form deviation of the ground surface in to account to determine the actual depth beneath surface, the accuracy of the SSD-evaluation could be improved significantly. The experiments reveal a clear influence of the cutting speed on SSD, higher cutting speeds generate less SSD. Besides the influence on the maximum crack depth an influence on the crack length itself could be verified. Based on image analysis it was possible, to predict the maximum depth of cracks by means of crack length.

  9. The compaction of fused silica resulting from ion implantation

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, C.M.; Ridgway, M.C. [Australian National Univ., Canberra, ACT (Australia); Leech, P.L. [Telstra Research Laboratories, Clayton, Victoria (Australia)

    1996-12-31

    Ion implantation of fused silica results in compaction and consequently an increase in refractive index. This method of modifying the near-surface region has been shown as a potential means for fabricating single mode channel waveguides. This study has measured the compaction of the implanted regions for Si implantations as a function of dose (2x10{sup 12} - 6x10{sup l6} ions/cm{sup 2}), energy (1-9 MeV) and post-implantation annealing temperature (200-900 degree C). For a given energy, a dose-dependence of the step height (depth of compacted region) is observed for doses less than {approx}10{sup 15} ions/cm{sup 2}. At higher doses the step height saturates. For a given dose, a linear trend is evident for the step height as a function of energy suggesting that the major mechanism for this compaction is electronic stopping. As the annealing temperature increases, the step height gradually decreases from {approx}0.1-0.2 {mu} to -10-20% of the original value. From the annealing data, it is possible to extract an activation energy of 0.08 eV associated with the thermal removal of the compacted region. 4 refs., 4 figs.

  10. Picosecond laser damage of fused silica at 355 nm

    International Nuclear Information System (INIS)

    Meng Xiangjie; Liu Hongjie; Wang Fang; Zhang Zhen; An Xinyou; Huang Jin; Jiang Xiaodong; Wu Weidong; Ren Weiyi

    2013-01-01

    This paper studies the initiated damage threshold, the damage morphology and the subsequent damage growth on fused silica's input-surface and exit-surface under picosecond laser irradiation at 355 nm. Defects induced fluorescence on surface of the optical component is observed. The results demonstrate a significant dependence of the initiated damage on pulse duration and surface defects, and that of the damage growth on self-focusing, sub-surface defects. The damage-threshold is 3.98 J/cm 2 of input surface and 2.91 J/cm 2 of exit surface. The damage morphologies are quite different between input surface and exit surface. Slow growth behavior appears for the diameter of exit-surface and linear growth one for the depth of exit-surface in the lateral side of damage site with the increase of shot number. Defects have changed obviously compared with nanosecond laser damage in the damage area. Several main reasons such as electric intensification and self-focusing for the observed initiated damage and damage growth behavior are discussed. (authors)

  11. High strain rate fracture behaviour of fused silica

    International Nuclear Information System (INIS)

    Ruggiero, A; Iannitti, G; Testa, G; Bonora, N; Limido, J; Lacome, J L; Olovsson, L; Ferraro, M

    2014-01-01

    Fused silica is a high purity synthetic amorphous silicon dioxide characterized by low thermal expansion coefficient, excellent optical qualities and exceptional transmittance over a wide spectral range. Because of its wide use in the military industry as window material, it may be subjected to high-energy ballistic impacts. Under such dynamic conditions, post-yield response of the ceramic as well as the strain rate related effects become significant and should be accounted for in the constitutive modelling. In this study, the Johnson-Holmquist (J-H) model parameters have been identified by inverse calibration technique, on selected validation test configurations, according to the procedure described hereafter. Numerical simulations were performed with LS-DYNA and IMPETUS-FEA, a general non-linear finite element software which offers NURBS finite element technology for the simulation of large deformation and fracture in materials. In order to overcome numerical drawbacks associated with element erosion, a modified version of the J-H model is proposed.

  12. Fused silica segments: a possible solution for x-ray telescopes with very high angular resolution like Lynx/XRS

    Science.gov (United States)

    Salmaso, Bianca; Basso, Stefano; Civitani, Marta; Ghigo, Mauro; Hołyszko, Joanna; Spiga, Daniele; Vecchi, Gabriele; Pareschi, Giovanni

    2017-09-01

    In order to look beyond Chandra, the Lynx/XRS mission has been proposed in USA and is currently studied by NASA. The optic will have an effective area of 2.5 m2 and an angular resolution of 0.5 arcsec HEW at 1 keV. In order to fulfill these requirements different technologies are considered, with the approaches of both full and segmented shells (that, possibly, can be also combined together). Concerning the production of segmented mirrors, a variety of thin substrates (glass, metal, silicon) are envisaged, that can be produced using both direct polishing or replication methods. Innovative post-fabrication correction methods (such as piezoelectric or magneto-restrictive film actuators on the back surface, differential deposition, ion implantation) are being also considered in order to reach the final tolerances. In this paper we are presenting a technology development based on fused silica (SiO2) segmented substrates, owing the low coefficient of thermal expansion of Fused Silica and its high chemical stability compared to other glasses. Thin SiO2 segmented substrates (typically 2 mm thick) are figured by direct polishing combined with final profile ion figuring correction, while the roughness reduction is reached with pitch tools. For the profile and roughness correction, the segments are glued to a substrate. In this paper we present the current status of this technology.

  13. Gas-liquid chromatography of bacterial fatty acids with a fused-silica capillary column.

    OpenAIRE

    Moss, C W; Dees, S B; Guerrant, G O

    1980-01-01

    The use of flexible, fused-silica capillary column for gas-liquid chromatographic analysis of bacterial fatty acids is illustrated with Propionibacterium acnes, Propionibacterium shermanii, and a standard methyl ester mixture.

  14. Imaging subsurface damage of grinded fused silica optics by confocal fluorescence microscopy

    OpenAIRE

    NEAUPORT, Jérôme; Cormont, P; Legros, P; Ambard, C; Destribats, J

    2009-01-01

    International audience; We report an experimental investigation of fluorescence confocal microscopy as a tool to measure subsurface damage on grinded fused silica optics. Confocal fluorescence microscopy was performed with an excitation at the wavelength of 405 nm on fixed abrasive diamond grinded fused silica samples. We detail the measured fluorescence spectrums and compare them to those of oil based coolants and grinding slurries. We evidence that oil based coolant used in diamond grinding...

  15. The adsorption behavior between particle contamination and fused silica in high-energy laser system

    Science.gov (United States)

    Bai, Q. S.; He, X.; Zhang, K.; Yang, W.; Zhang, F. H.; Yuan, X. D.

    2017-08-01

    In high-energy laser facility, the residual nano-particles that are remained in mechanical system or produced by the interaction of kinetic-pairs are inevitable. The generation and the propagation of particulate pollutants will seriously reduce the performance of the laser systems. Therefore, the research about the adsorption behavior of particle contaminants on fused silica is very important to maintain the optical components' surface clean, reduce induced damage, and finally prolong the life of the optical components. In this paper, the adsorption behavior between aluminum nano-particles and fused silica was simulated by molecular dynamics method. The effect of the surface roughness of fused silica on the state of adsorption and the state before adsorption has been studied. Then an experiment system based on an atomic force microscope was established to measure the adsorption force and further to verify the simulated results. Finally, the adsorption mechanism between metallic nano-particles and fused silica was revealed. The results show that surface roughness and the size of the particles are two of the main factors to influence the adsorption force. The rough fused silica surface can be "particle-phobic" due to the decreased contact area, which is beneficial to keep the fused silica surface clean.

  16. Subsurface defects of fused silica optics and laser induced damage at 351 nm.

    Science.gov (United States)

    Hongjie, Liu; Jin, Huang; Fengrui, Wang; Xinda, Zhou; Xin, Ye; Xiaoyan, Zhou; Laixi, Sun; Xiaodong, Jiang; Zhan, Sui; Wanguo, Zheng

    2013-05-20

    Many kinds of subsurface defects are always present together in the subsurface of fused silica optics. It is imperfect that only one kind of defects is isolated to investigate its impact on laser damage. Therefore it is necessary to investigate the impact of subsurface defects on laser induced damage of fused silica optics with a comprehensive vision. In this work, we choose the fused silica samples manufactured by different vendors to characterize subsurface defects and measure laser induced damage. Contamination defects, subsurface damage (SSD), optical-thermal absorption and hardness of fused silica surface are characterized with time-of-flight secondary ion mass spectrometry (TOF-SIMS), fluorescence microscopy, photo-thermal common-path interferometer and fully automatic micro-hardness tester respectively. Laser induced damage threshold and damage density are measured by 351 nm nanosecond pulse laser. The correlations existing between defects and laser induced damage are analyzed. The results show that Cerium element and SSD both have a good correlation with laser-induced damage thresholds and damage density. Research results evaluate process technology of fused silica optics in China at present. Furthermore, the results can provide technique support for improving laser induced damage performance of fused silica.

  17. Solubility of fused silica in sub- and supercritical water: Estimation from a thermodynamic model

    Czech Academy of Sciences Publication Activity Database

    Karásek, Pavel; Šťavíková, Lenka; Planeta, Josef; Hohnová, Barbora; Roth, Michal

    2013-01-01

    Roč. 83, NOV (2013), s. 72-77 ISSN 0896-8446 R&D Projects: GA ČR(CZ) GAP106/12/0522 Institutional support: RVO:68081715 Keywords : amorphous silica * fused silica * supercritical water * aqueous solubility Subject RIV: CB - Analytical Chemistry, Separation Impact factor: 2.571, year: 2013

  18. Imaging subsurface damage of grinded fused silica optics by confocal fluorescence microscopy.

    Science.gov (United States)

    Neauport, J; Cormont, P; Legros, P; Ambard, C; Destribats, J

    2009-03-02

    We report an experimental investigation of fluorescence confocal microscopy as a tool to measure subsurface damage on grinded fused silica optics. Confocal fluorescence microscopy was performed with an excitation at the wavelength of 405 nm on fixed abrasive diamond grinded fused silica samples. We detail the measured fluorescence spectrums and compare them to those of oil based coolants and grinding slurries. We evidence that oil based coolant used in diamond grinding induces a fluorescence that marks the subsurface damages and eases its observation. Such residual traces might also be involved in the laser damage process.

  19. Formation of nanograting in fused silica by temporally delayed femtosecond double-pulse irradiation

    Science.gov (United States)

    Wang, Haodong; Song, Juan; Li, Qin; Zeng, Xianglong; Dai, Ye

    2018-04-01

    A 1 kHz femtosecond double-pulse sequence irradiation is used to study the temporal evolution of nanograting in fused silica by controlling the delay times and polarization combinations of two independent beams from a Mach–Zehnder interferometer. A lateral laser-scan experiment with speed at 5 µm s‑1 and each pulse energy of 1 µJ is firstly performed with the delay time from sub-picosecond to 10 ps, and then the written nanostructures are systematically studied under a cross-polarized microscope because the intensity of birefringence signal nearly corresponds to optical retardance and development level of the induced nanograting. The trend shows that the induced nanogratings can continue developing with a decrease of delay time in the case of the linear polarization pulse arriving before. In another vertical laser-scan experiment at the same speed and pulse energy, the morphologies of nanogratings embedded in the lines are characterized by scanning electron microscope after mechanical polishing and chemical etching. The self-organized patterns have a commonly spatial period of 200–300 nm and the orientation is always perpendicular to the polarization of the first laser pulse, and the second pulse in each sequence seems to promote the as-formed nanograting developing further even if the polarized direction is different from the previous pulse. These new findings verify again that a localized memory effect can make positive feedback to reinforce the patterned nanostripes. In that process, the impact ionization from the seed electrons left by the first pulse excitation and the photoionization of self-trapped excitons with lower ionization threshold results in an increase of the re-excited carriers during the second pulse irradiation and the subsequent development of the as-formed nanograting. Our result provides further proofs for understanding the physical mechanism of nanograting strongly connection with the interplay on multiple ionization channels.

  20. Characterization of deep wet etching of fused silica glass for single cell and optical sensor deposition

    International Nuclear Information System (INIS)

    Zhu, Haixin; Holl, Mark; Ray, Tathagata; Bhushan, Shivani; Meldrum, Deirdre R

    2009-01-01

    The development of a high-throughput single-cell metabolic rate monitoring system relies on the use of transparent substrate material for a single cell-trapping platform. The high optical transparency, high chemical resistance, improved surface quality and compatibility with the silicon micromachining process of fused silica make it very attractive and desirable for this application. In this paper, we report the results from the development and characterization of a hydrofluoric acid (HF) based deep wet-etch process on fused silica. The pin holes and notching defects of various single-coated masking layers during the etching are characterized and the most suitable masking materials are identified for different etch depths. The dependence of the average etch rate and surface roughness on the etch depth, impurity concentration and HF composition are also examined. The resulting undercut from the deep HF etch using various masking materials is also investigated. The developed and characterized process techniques have been successfully implemented in the fabrication of micro-well arrays for single cell trapping and sensor deposition. Up to 60 µm deep micro-wells have been etched in a fused silica substrate with over 90% process yield and repeatability. To our knowledge, such etch depth has never been achieved in a fused silica substrate by using a non-diluted HF etchant and a single-coated masking layer at room temperature

  1. Near- and supercritical water as a diameter manipulation and surface roughening agent in fused silica capillaries

    Czech Academy of Sciences Publication Activity Database

    Karásek, Pavel; Planeta, Josef; Roth, Michal

    2013-01-01

    Roč. 85, č. 1 (2013), s. 327-333 ISSN 0003-2700 R&D Projects: GA ČR(CZ) GAP106/12/0522; GA ČR(CZ) GAP206/11/0138 Institutional support: RVO:68081715 Keywords : supercritical water * fused silica capillary * surface treatment Subject RIV: CB - Analytical Chemistry, Separation Impact factor: 5.825, year: 2013

  2. Bulk damage and absorption in fused silica due to high-power laser applications

    Science.gov (United States)

    Nürnberg, F.; Kühn, B.; Langner, A.; Altwein, M.; Schötz, G.; Takke, R.; Thomas, S.; Vydra, J.

    2015-11-01

    Laser fusion projects are heading for IR optics with high broadband transmission, high shock and temperature resistance, long laser durability, and best purity. For this application, fused silica is an excellent choice. The energy density threshold on IR laser optics is mainly influenced by the purity and homogeneity of the fused silica. The absorption behavior regarding the hydroxyl content was studied for various synthetic fused silica grades. The main absorption influenced by OH vibrational excitation leads to different IR attenuations for OH-rich and low-OH fused silica. Industrial laser systems aim for the maximum energy extraction possible. Heraeus Quarzglas developed an Yb-doped fused silica fiber to support this growing market. But the performance of laser welding and cutting systems is fundamentally limited by beam quality and stability of focus. Since absorption in the optical components of optical systems has a detrimental effect on the laser focus shift, the beam energy loss and the resulting heating has to be minimized both in the bulk materials and at the coated surfaces. In collaboration with a laser research institute, an optical finisher and end users, photo thermal absorption measurements on coated samples of different fused silica grades were performed to investigate the influence of basic material properties on the absorption level. High purity, synthetic fused silica is as well the material of choice for optical components designed for DUV applications (wavelength range 160 nm - 260 nm). For higher light intensities, e.g. provided by Excimer lasers, UV photons may generate defect centers that effect the optical properties during usage, resulting in an aging of the optical components (UV radiation damage). Powerful Excimer lasers require optical materials that can withstand photon energy close to the band gap and the high intensity of the short pulse length. The UV transmission loss is restricted to the DUV wavelength range below 300 nm and

  3. Polyurea/Fused-silica interfacial decohesion induced by impinging tensile stress-waves

    Directory of Open Access Journals (Sweden)

    Mica Grujicic

    2016-04-01

    Full Text Available All-atom non-equilibrium molecular-dynamics simulations are used to investigate the problems of polyurea-borne tensile-stress waves interacting with a polyurea/fused-silica interface and fused-silica tensile-stress waves interacting with a fused-silica/polyurea interface, and the potential for the accompanying interfacial decohesion. To predict the outcome of the interactions of stress-waves with the material-interfaces in question, at the continuum level, previously determined material constitutive relations for polyurea and fused-silica are used within an acoustic-impedance-matching procedure. These continuum-level predictions pertain solely to the stress-wave/interface interaction aspects resulting in the formation of transmitted and reflected stress- or release-waves, but do not contain any information regarding potential interfacial decohesion. Present direct molecular-level simulations confirmed some of these continuum-level predictions, but also provided direct evidence of the nature and the extent of interfacial decohesion. In the molecular-level simulations, reactive force-field potentials are utilized to properly model the initial state of interfacial cohesion and its degradation during stress-wave-loading. Examination of the molecular-level interfacial structure before the stress-wave has interacted with the given interface, revealed local changes in the bonding structure, suggesting the formation of an “interphase.” This interphase was subsequently found to greatly affect the polyurea/fused-silica decohesion strength and the likelihood for interfacial decohesion during the interaction of the stress-wave with the interface.

  4. Advanced Mitigation Process (AMP) for Improving Laser Damage Threshold of Fused Silica Optics

    Science.gov (United States)

    Ye, Xin; Huang, Jin; Liu, Hongjie; Geng, Feng; Sun, Laixi; Jiang, Xiaodong; Wu, Weidong; Qiao, Liang; Zu, Xiaotao; Zheng, Wanguo

    2016-08-01

    The laser damage precursors in subsurface of fused silica (e.g. photosensitive impurities, scratches and redeposited silica compounds) were mitigated by mineral acid leaching and HF etching with multi-frequency ultrasonic agitation, respectively. The comparison of scratches morphology after static etching and high-frequency ultrasonic agitation etching was devoted in our case. And comparison of laser induce damage resistance of scratched and non-scratched fused silica surfaces after HF etching with high-frequency ultrasonic agitation were also investigated in this study. The global laser induce damage resistance was increased significantly after the laser damage precursors were mitigated in this case. The redeposition of reaction produce was avoided by involving multi-frequency ultrasonic and chemical leaching process. These methods made the increase of laser damage threshold more stable. In addition, there is no scratch related damage initiations found on the samples which were treated by Advanced Mitigation Process.

  5. Evolution of Oxygen Deficiency Center on Fused Silica Surface Irradiated by Ultraviolet Laser and Posttreatment

    Directory of Open Access Journals (Sweden)

    Hai-Bing Lü

    2014-01-01

    Full Text Available Evolution of oxygen deficiency centers (ODCs on a fused silica surface irradiated using a 355 nm ultraviolet (UV laser beam in both vacuum and atmospheric conditions was quantitatively studied using photoluminescence and X-ray photoelectron spectroscopy. When the fusedsilica surface was exposed to the UV laser in vacuum, the laser damage threshold was decreased whereas the concentration of the ODCs was increased. For the fuse silica operated under the high power lasers, creation of ODCs on their surface resulted from the UV laser irradiation, and this is more severe in a high vacuum. The laser fluence and/or laser intensity have significant effects on the increase of the ODCs concentration. The ODCs can be effectively repaired using postoxygen plasma treatment and UV laser irradiation in an excessive oxygen environment. Results also demonstrated that the “gain” and “loss” of oxygen at the silica surface is a reversible and dynamic process.

  6. Particle damage sources for fused silica optics and their mitigation on high energy laser systems.

    Science.gov (United States)

    Bude, J; Carr, C W; Miller, P E; Parham, T; Whitman, P; Monticelli, M; Raman, R; Cross, D; Welday, B; Ravizza, F; Suratwala, T; Davis, J; Fischer, M; Hawley, R; Lee, H; Matthews, M; Norton, M; Nostrand, M; VanBlarcom, D; Sommer, S

    2017-05-15

    High energy laser systems are ultimately limited by laser-induced damage to their critical components. This is especially true of damage to critical fused silica optics, which grows rapidly upon exposure to additional laser pulses. Much progress has been made in eliminating damage precursors in as-processed fused silica optics (the advanced mitigation process, AMP3), and very high damage resistance has been demonstrated in laboratory studies. However, the full potential of these improvements has not yet been realized in actual laser systems. In this work, we explore the importance of additional damage sources-in particular, particle contamination-for fused silica optics fielded in a high-performance laser environment, the National Ignition Facility (NIF) laser system. We demonstrate that the most dangerous sources of particle contamination in a system-level environment are laser-driven particle sources. In the specific case of the NIF laser, we have identified the two important particle sources which account for nearly all the damage observed on AMP3 optics during full laser operation and present mitigations for these particle sources. Finally, with the elimination of these laser-driven particle sources, we demonstrate essentially damage free operation of AMP3 fused silica for ten large optics (a total of 12,000 cm 2 of beam area) for shots from 8.6 J/cm 2 to 9.5 J/cm 2 of 351 nm light (3 ns Gaussian pulse shapes). Potentially many other pulsed high energy laser systems have similar particle sources, and given the insight provided by this study, their identification and elimination should be possible. The mitigations demonstrated here are currently being employed for all large UV silica optics on the National Ignition Facility.

  7. Fiber fuse light-induced continuous breakdown of silica glass optical fiber

    CERN Document Server

    Todoroki, Shin-ichi

    2014-01-01

    This book describes the fiber fuse phenomenon that causes a serious problem for the present optical communication systems. High-power light often brings about catastrophic damage to optical devices. Silica glass optical fibers with ultralow transmission loss are not the exception. A fiber fuse appears in a heated region of the fiber cable delivering a few watts of light and runs toward the light source destroying its core region. Understanding this phenomenon is a necessary first step in the development of future optical communication systems. This book provides supplementary videos and photog

  8. The size prediction of potential inclusions embedded in the sub-surface of fused silica by damage morphology

    Directory of Open Access Journals (Sweden)

    Gao Xiang

    2017-04-01

    Full Text Available A model for predicting the size ranges of different potential inclusions initiating damage on the surface of fused silica has been presented. This accounts for the heating of nanometric inclusions whose absorptivity is described based on Mie Theory. The depth profile of impurities has been measured by ICP-OES. By the measured temporal pulse profile on the surface of fused silica, the temperature and thermal stress has been calculated. Furthermore, considering the limit conditions of temperature and thermal stress strength for different damage morphologies, the size range of potential inclusions for fused silica is discussed.

  9. The size prediction of potential inclusions embedded in the sub-surface of fused silica by damage morphology

    Science.gov (United States)

    Gao, Xiang; Qiu, Rong; Wang, Kunpeng; Zhang, Jiangmei; Zhou, Guorui; Yao, Ke; Jiang, Yong; Zhou, Qiang

    2017-04-01

    A model for predicting the size ranges of different potential inclusions initiating damage on the surface of fused silica has been presented. This accounts for the heating of nanometric inclusions whose absorptivity is described based on Mie Theory. The depth profile of impurities has been measured by ICP-OES. By the measured temporal pulse profile on the surface of fused silica, the temperature and thermal stress has been calculated. Furthermore, considering the limit conditions of temperature and thermal stress strength for different damage morphologies, the size range of potential inclusions for fused silica is discussed.

  10. Front-surface fabrication of moderate aspect ratio micro-channels in fused silica by single picosecond Gaussian-Bessel laser pulse

    Science.gov (United States)

    Liu, Xin; Sanner, Nicolas; Sentis, Marc; Stoian, Razvan; Zhao, Wei; Cheng, Guanghua; Utéza, Olivier

    2018-02-01

    Single-shot Gaussian-Bessel laser beams of 1 ps pulse duration and of 0.9 μm core size and 60 μm depth of focus are used for drilling micro-channels on front side of fused silica in ambient condition. Channels ablated at different pulse energies are fully characterized by AFM and post-processing polishing procedures. We identify experimental energy conditions (typically 1.5 µJ) suitable to fabricate non-tapered channels with mean diameter of 1.2 µm and length of 40 μm while maintaining an utmost quality of the front opening of the channels. In addition, by further applying accurate post-polishing procedure, channels with high surface quality and moderate aspect ratio down to a few units are accessible, which would find interest in the surface micro-structuring of materials, with perspective of further scalability to meta-material specifications.

  11. Controllable damping of high-Q violin modes in fused silica suspension fibers

    Energy Technology Data Exchange (ETDEWEB)

    Dmitriev, A V; Mescheriakov, S D; Mitrofanov, V P [Faculty of Physics, Moscow State University, Moscow 119991 (Russian Federation); Tokmakov, K V, E-mail: dmitriev@hbar.phys.msu.r, E-mail: mitr@hbar.phys.msu.r [Present address: Department of Physics, SUPA, University of Strathclyde, Glasgow G4 0NG (United Kingdom)

    2010-01-21

    Fused silica fiber suspension of the test masses will be used in the interferometric gravitational wave detectors of the next generation. This allows a significant reduction of losses in the suspension and thermal noise associated with the suspension. Unfortunately, unwanted violin modes may be accidentally excited in the suspension fibers. The Q-factor of the violin modes also exceeds 10{sup 8}. They have a ring-down time that is too long and may complicate the stable control of the interferometer. Results of the investigation of a violin mode active damping system are described. An original sensor and actuator were especially developed to realize the effective coupling of a thin, optically transparent, non-conducting fused silica fiber with an electric circuit. The damping system allowed the changing of the violin mode's damping rate over a wide range.

  12. Controllable damping of high-Q violin modes in fused silica suspension fibers

    Science.gov (United States)

    Dmitriev, A. V.; Mescheriakov, S. D.; Tokmakov, K. V.; Mitrofanov, V. P.

    2010-01-01

    Fused silica fiber suspension of the test masses will be used in the interferometric gravitational wave detectors of the next generation. This allows a significant reduction of losses in the suspension and thermal noise associated with the suspension. Unfortunately, unwanted violin modes may be accidentally excited in the suspension fibers. The Q-factor of the violin modes also exceeds 108. They have a ring-down time that is too long and may complicate the stable control of the interferometer. Results of the investigation of a violin mode active damping system are described. An original sensor and actuator were especially developed to realize the effective coupling of a thin, optically transparent, non-conducting fused silica fiber with an electric circuit. The damping system allowed the changing of the violin mode's damping rate over a wide range.

  13. Controllable damping of high-Q violin modes in fused silica suspension fibers

    International Nuclear Information System (INIS)

    Dmitriev, A V; Mescheriakov, S D; Mitrofanov, V P; Tokmakov, K V

    2010-01-01

    Fused silica fiber suspension of the test masses will be used in the interferometric gravitational wave detectors of the next generation. This allows a significant reduction of losses in the suspension and thermal noise associated with the suspension. Unfortunately, unwanted violin modes may be accidentally excited in the suspension fibers. The Q-factor of the violin modes also exceeds 10 8 . They have a ring-down time that is too long and may complicate the stable control of the interferometer. Results of the investigation of a violin mode active damping system are described. An original sensor and actuator were especially developed to realize the effective coupling of a thin, optically transparent, non-conducting fused silica fiber with an electric circuit. The damping system allowed the changing of the violin mode's damping rate over a wide range.

  14. Birefringence and residual stress induced by CO2 laser mitigation of damage growth in fused silica

    Science.gov (United States)

    Gallais, L.; Cormont, P.; Rullier, J. L.

    2009-10-01

    We investigate the residual stress field created near mitigated sites and its influence on the efficiency on the CO2 laser mitigation of damage growth process. A numerical model of CO2 laser interaction with fused silica is developed that take into account laser energy absorption, heat transfer, thermally-induced stress and birefringence. Specific photoelastic methods are developed to characterize the residual stress near mitigated sites in fused silica samples. The stress distribution and quantitative values of stress levels are obtained for sites treated with the CO2 laser in various conditions of energy deposition (beam size, pulse duration, incident power). The results obtained also show that the presence of birefringence/residual stress around the mitigated sites has a critical effect on their laser damage resistance.

  15. Microwave interrogated large core fused silica fiber Michelson interferometer for strain sensing.

    Science.gov (United States)

    Hua, Liwei; Song, Yang; Huang, Jie; Lan, Xinwei; Li, Yanjun; Xiao, Hai

    2015-08-20

    A Michelson-type large core optical fiber sensor has been developed, which is designed based on the optical carrier-based microwave interferometry technique, and fabricated by using two pieces of 200-μm diameter fused silica core fiber as two arms of the Michelson interferometer. The interference fringe pattern caused by the optical path difference of the two arms is interrogated in the microwave domain, where the fringe visibility of 40 dB has easily been obtained. The strain sensing at both room temperature and high temperatures has been demonstrated by using such a sensor. Experimental results show that this sensor has a linear response to the applied strain, and also has relatively low temperature-strain cross talk. The dopant-free quality of the fused silica fiber provides high possibility for the sensor to have promising strain sensing performance in a high temperature environment.

  16. An internally reflecting Cherenkov detector (DIRC): Properties of the fused silica radiators

    International Nuclear Information System (INIS)

    Adam, I.; Aston, D.

    1997-11-01

    The DIRC, a new type of ring-imaging Cherenkov detector that images internally reflected Cherenkov light, is being constructed as the main hadronic particle identification component of the BABAR detector at SLAC. The device makes use of 5 meter long fused silica (colloquially called quartz) bars, which serve both as the Cherenkov radiators and as light pipes for transmitting the light to an array of photo-multiplier tubes. This paper describes a program of research and development aimed at determining whether bars that meet the stringent requirements of the DIRC can be obtained from commercial sources. The results of studies of bulk absorption of fused silica, surface finish, radiation damage and bulk inhomogeneities are discussed

  17. Measurements of effective noise temperature in fused silica fiber violin modes

    Energy Technology Data Exchange (ETDEWEB)

    Bilenko, I.A.; Lourie, S.L

    2002-11-25

    The results of measurements of the effective noise temperature in fused silica fiber violin modes are presented. In these measurements the fibers were stressed and value of the effective noise temperature was obtained by direct observation of oscillations in the fundamental violin modes of several samples. Measured values indicate that effective noise temperature does not exceed the room temperature significantly. This result is important for the design of the advanced gravitational wave antennae.

  18. Densification and Devitrification of Fused Silica Induced by Ballistic Impact: A Computational Investigation

    Science.gov (United States)

    2015-03-25

    bend - torsion interactions between a Journal of Nanomaterials 5 dihedral angle and one of its valence angles; and (g) bend - bend - torsion interactions...atomic- scale simulation of fused silica under combined pres- sure/shear loading conditions. The results obtained estab- lished permanent/irreversible...electrons bonding and contains the following components: (a) a bond length/stretching term; (b) a two- bond angle term; (c) a three-bond dihedral/ torsion

  19. Supercritical water-treated fused silica capillaries in analytical separations: Status review

    Czech Academy of Sciences Publication Activity Database

    Karásek, Pavel; Horká, Marie; Šlais, Karel; Planeta, Josef; Roth, Michal

    2018-01-01

    Roč. 1539, MAR (2018), s. 1-11 ISSN 0021-9673 R&D Projects: GA MV VI20172020069; GA ČR(CZ) GA16-03749S; GA MZd(CZ) NV16-29916A Institutional support: RVO:68081715 Keywords : supercritical water * fused silica capillary * surface treatment Subject RIV: CB - Analytical Chemistry, Separation OBOR OECD: Analytical chemistry Impact factor: 3.981, year: 2016

  20. Ab initio modeling of fused silica, crystal quartz, and water Raman spectra

    Czech Academy of Sciences Publication Activity Database

    Dračínský, Martin; Benda, Ladislav; Bouř, Petr

    2011-01-01

    Roč. 512, č. 13 (2011), s. 54-59 ISSN 0009-2614 R&D Projects: GA ČR GAP208/11/0105; GA MŠk(CZ) LH11033 Grant - others:GA MŠk(CZ) 2B08021 Program:2B Institutional research plan: CEZ:AV0Z40550506 Keywords : fused silica * Raman spectroscopy * Car -Parrinello molecular dynamics Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 2.337, year: 2011

  1. Measurements of effective noise temperature in fused silica fiber violin modes

    International Nuclear Information System (INIS)

    Bilenko, I.A.; Lourie, S.L.

    2002-01-01

    The results of measurements of the effective noise temperature in fused silica fiber violin modes are presented. In these measurements the fibers were stressed and value of the effective noise temperature was obtained by direct observation of oscillations in the fundamental violin modes of several samples. Measured values indicate that effective noise temperature does not exceed the room temperature significantly. This result is important for the design of the advanced gravitational wave antennae

  2. Single-Molecule Imaging of DNAs with Sticky Ends at Water/Fused Silica Interface

    Energy Technology Data Exchange (ETDEWEB)

    Isailovic, Slavica [Iowa State Univ., Ames, IA (United States)

    2005-01-01

    Total internal reflection fluorescence microscopy (TIRFM) was used to study intermolecular interactions of DNAs with unpaired (sticky) ends of different lengths at water/fused silica interface at the single-molecule level. Evanescent field residence time, linear velocity and adsorption/desorption frequency were measured in a microchannel for individual DNA molecules from T7, Lambda, and PSP3 phages at various pH values. The longest residence times and the highest adsorption/desorption frequencies at the constant flow at pH 5.5 were found for PSP3 DNA, followed by lower values for Lambda DNA, and the lowest values for T7 DNA. Since T7, Lambda, and PSP3 DNA molecules contain none, twelve and nineteen unpaired bases, respectively, it was concluded that the affinity of DNAs for the surface increases with the length of the sticky ends. This confirms that hydrophobic and hydrogen-bonding interactions between sticky ends and fused-silica surface are driving forces for DNA adsorption at the fused-silica surface. Described single-molecule methodology and results therein can be valuable for investigation of interactions in liquid chromatography, as well as for design of DNA hybridization sensors and drug delivery systems.

  3. Self-fabrication of void array in fused silica by femtosecond laser processing

    International Nuclear Information System (INIS)

    Toratani, Eiji; Kamata, Masanao; Obara, Minoru

    2005-01-01

    We demonstrate self-fabrication of a submicrometer-sized void array in fused silica using a 100 fs 0.2-3 μJ Ti:Sapphire femtosecond laser and a high 0.9 numerical aperture (NA) objective lens. The effect of the focusing conditions of NA, laser energy, and pulse number on the shape of the fabricated void was investigated. The void has a linearly drawn shape in the direction of the laser irradiation when a single pulse is irradiated and an increasing number of incident pulses resulted in the break up of the long void into multiple spherical ones, leading to a periodically aligned void array. The void shape also varied with the depth of the focus point beneath the fused silica surface, because the amount of self-focusing has a significant effect on the generation of the voids. The void shape was narrower and longer when the laser pulse was focused with the higher NA (up to 0.9) objective lens in the deeper position (up to 70 μm) in the fused silica

  4. Precision drilling of fused silica with 157-nm excimer laser radiation

    Science.gov (United States)

    Temme, Thorsten; Ostendorf, Andreas; Kulik, Christian; Meyer, Klaus

    2003-07-01

    μFor drilling fused silica, mechanical techniques like with diamond drills, ultrasonic machining, sand blasting or water jet machining are used. Also chemical techniques like laser assisted wet etching or thermal drilling with CO2-lasers are established. As an extension of these technologies, the drilling of micro-holes in fused silica with VUV laser radiation is presented here. The high absorption of the 157 nm radiation emitted by the F2 excimer laser and the short pulse duration lead to a material ablation with minimised impact on the surrounding material. Contrary to CO2-laser drilling, a molten and solidified phase around the bore can thus be avoided. The high photon energy of 7.9 eV requires either high purity nitrogen flushing or operation in vacuum, which also effects the processing results. Depending on the required precision, the laser can be used for percussion drilling as well as for excimer laser trepanning, by applying rotating masks. Rotating masks are especially used for high aspect ratio drilling with well defined edges and minimised debris. The technology is suitable particularly for holes with a diameter below 200 μm down to some microns in substrates with less than 200 μm thickness, that can not be achieved with mechanical methods. Drilling times in 200 μm fused silica substrates are in the range of ten seconds, which is sufficient to compete with conventional methods while providing similar or even better accuracy.

  5. Evaluation of optical properties of the amorphous carbon film on fused silica

    International Nuclear Information System (INIS)

    Baydogan, Nilguen Dogan

    2004-01-01

    Deposition was done using a pulsed filtered cathodic arc with a graphite cathode. The carbon plasma is fully ionised and condenses on the substrate, forming diamond-like material but with amorphous structure. Optical properties of amorphous carbon films on fused-silica glass were investigated and the curves of optical density have a characteristic band at approximately 950 nm. Changes of the colourimetric quantities were evaluated and compared to uncoated fused silica glass. These changes were investigated as a function of the applied substrate bias voltage using the CIE and CIELAB colour systems. It is suggested that the mechanism of absorption is related to an allowed direct transition at the amorphous carbon films on fused silica glass. The optical energy gap of the amorphous carbon film depends on the bias voltage applied to the substrate holder. The optical colour parameters and optical band gap indicated that there is a relation between the dominant wavelength of the reflectance in the visible range and the wavelength of the optical band gap

  6. Influence of piezoceramic to fused silica plate thickness on the radii of curvature of piezoelectric bimorph mirror

    International Nuclear Information System (INIS)

    Libu, M.; Susanth, S.; Vasanthakumari, K. G.; Dileep Kumar, C. J.; Raghu, N.

    2012-01-01

    Piezoelectric based bimorph mirrors (PBM) find extensive use in focusing of x-ray beams. Many optical instruments require use of PBM whose radii of curvature can be tuned precisely. The 100 mm and 300 mm PBMs were fabricated with varying piezoelectric to fused silica plate thicknesses. The radii of curvature of free standing mirrors were measured as a function of voltage and it was found to decrease with increasing voltage. For a given piezoelectric plate thickness, as the fused silica thickness increases, the radii of curvature was found to increase owing to increase in stiffness of the mirror. On the other hand, for a given fused silica plate thickness, when the piezoelectric plate thickness is increased, the radii of curvature are decreased for a given electric field, due to increase in generated force. This study brings out the influence of piezoceramic to fused silica plate thickness on the radii of curvature of PBM.

  7. A new method for synthesizing fluid inclusions in fused silica capillaries containing organic and inorganic material

    Science.gov (United States)

    Chou, I.-Ming; Song, Yucai; Burruss, R. C.

    2008-11-01

    Considerable advances in our understanding of physicochemical properties of geological fluids and their roles in many geological processes have been achieved by the use of synthetic fluid inclusions. We have developed a new method to synthesize fluid inclusions containing organic and inorganic material in fused silica capillary tubing. We have used both round (0.3 mm OD and 0.05 or 0.1 mm ID) and square cross-section tubing (0.3 × 0.3 mm with 0.05 × 0.05 mm or 0.1 × 0.1 mm cavities). For microthermometric measurements in a USGS-type heating-cooling stage, sample capsules must be less than 25 mm in length. The square-sectioned capsules have the advantage of providing images without optical distortion. However, the maximum internal pressure ( P; about 100 MPa at 22 °C) and temperature ( T; about 500 °C) maintained by the square-sectioned capsules are less than those held by the round-sectioned capsules (about 300 MPa at room T, and T up to 650 °C). The fused silica capsules can be applied to a wide range of problems of interest in fluid inclusion and hydrothermal research, such as creating standards for the calibration of thermocouples in heating-cooling stages and frequency shifts in Raman spectrometers. The fused silica capsules can also be used as containers for hydrothermal reactions, especially for organic samples, including individual hydrocarbons, crude oils, and gases, such as cracking of C 18H 38 between 350 and 400 °C, isotopic exchanges between C 18H 38 and D 2O and between C 19D 40 and H 2O at similar temperatures. Results of these types of studies provide information on the kinetics of oil cracking and the changes of oil composition under thermal stress. When compared with synthesis of fluid inclusions formed by healing fractures in quartz or other minerals or by overgrowth of quartz at elevated P- T conditions, the new fused-silica method has the following advantages: (1) it is simple; (2) fluid inclusions without the presence of water can be

  8. Deep reactive ion etching of fused silica using a single-coated soft mask layer for bio-analytical applications

    International Nuclear Information System (INIS)

    Ray, Tathagata; Zhu, Haixin; Meldrum, Deirdre R

    2010-01-01

    In this note, we present our results from process development and characterization of reactive ion etching (RIE) of fused silica using a single-coated soft masking layer (KMPR® 1025, Microchem Corporation, Newton, MA). The effects of a number of fluorine-radical-based gaseous chemistries, the gas flow rate, RF power and chamber pressure on the etch rate and etching selectivity of fused silica were studied using factorial experimental designs. RF power and pressure were found to be the most important factors in determining the etch rate. The highest fused silica etch rate obtained was about 933 Å min −1 by using SF 6 -based gas chemistry, and the highest etching selectivity between the fused silica and KMPR® 1025 was up to 1.2 using a combination of CF 4 , CHF 3 and Ar. Up to 30 µm deep microstructures have been successfully fabricated using the developed processes. The average area roughness (R a ) of the etched surface was measured and results showed it is comparable to the roughness obtained using a wet etching technique. Additionally, near-vertical sidewalls (with a taper angle up to 85°) have been obtained for the etched microstructures. The processes developed here can be applied to any application requiring fabrication of deep microstructures in fused silica with near-vertical sidewalls. To our knowledge, this is the first note on deep RIE of fused silica using a single-coated KMPR® 1025 masking layer and a non-ICP-based reactive ion etcher. (technical note)

  9. Electrical field-induced faceting of etched features using plasma etching of fused silica

    Science.gov (United States)

    Huff, M.; Pedersen, M.

    2017-07-01

    This paper reports a previously unreported anomaly that occurs when attempting to perform deep, highly anisotropic etches into fused silica using an Inductively-Coupled Plasma (ICP) etch process. Specifically, it was observed that the top portion of the etched features exhibited a substantially different angle compared to the vertical sidewalls that would be expected in a typical highly anisotropic etch process. This anomaly has been termed as "faceting." A possible explanation of the mechanism that causes this effect and a method to eradicate it has been developed. Additionally, the method to eliminate the faceting is demonstrated. It is theorized that this faceting is a result of the interaction of the electro-potential electrical fields that surround the patterned nickel layers used as a hard mask and the electrical fields directing the high-energy ions from the plasma to the substrate surface. Based on this theory, an equation for calculating the minimum hard mask thickness required for a desired etch depth into fused silica to avoid faceting was derived. As validation, test samples were fabricated employing hard masks of thicknesses calculated based on the derived equation, and it was found that no faceting was observed on these samples, thereby demonstrating that the solution performed as predicted. Deep highly anisotropic etching of fused silica, as well as other forms of silicon dioxide, including crystalline quartz, using plasma etching, has an important application in the fabrication of several MEMS, NEMS, microelectronic, and photonic devices. Therefore, a method to eliminate faceting is an important development for the accurate control of the dimensions of deep and anisotropic etched features of these devices using ICP etch technology.

  10. Growth of laser damage in fused silica: diameter to depth ratio

    Energy Technology Data Exchange (ETDEWEB)

    Norton, M A; Adams, J J; Carr, C W; Donohue, E E; Feit, M D; Hackel, R P; Hollingsworth, W G; Jarboe, J A; Matthews, M; Rubenchik, A M; Spaeth, M L

    2007-10-29

    Growth of laser initiated damage plays a major role in determining optics lifetime in high power laser systems. Previous measurements have established that the lateral diameter grows exponentially. Knowledge of the growth of the site in the propagation direction is also important, especially so when considering techniques designed to mitigate damage growth, where it is required to reach all the subsurface damage. In this work, we present data on both the diameter and the depth of a growing exit surface damage sites in fused silica. Measured growth rates with both 351 nm illumination and with combined 351 nm and 1054 nm illumination are discussed.

  11. Femtosecond laser induced rotated 3D self-organized nanograting in fused silica.

    Science.gov (United States)

    Dai, Ye; Wu, Guorui; Lin, Xian; Ma, Guohong; Qiu, Jianrong

    2012-07-30

    Formation of rotated 3D self-organized nanograting inside fused silica is demonstrated by using a femtosecond pulse laser. The difference of birefringence signal of non-reciprocal writing lines indicates that the excited pulses may possess a finite tilt of intensity front, which produces an electric field vector parallel to the incident direction to modulate the excited electron plasma. We suggest that the orientation of nanograting depends on the correlation between the polarization plane azimuth and the tilted intensity front based on previous investigations. The result provides an opportunity to control the rotation of self-organized nanograting in three-dimensional space.

  12. Attenuated total reflectance spectroscopy of coumarin organosilane molecules adsorbed on a fused silica surface

    International Nuclear Information System (INIS)

    Bratescu, Maria Antoaneta; Saito, Nagahiro; Takai, Osamu

    2010-01-01

    Attenuated total reflectance (ATR) spectroscopy was used to investigate the adsorption of coumarin organosilane molecules onto a fused silica surface. The difference between the absorption spectra of the molecules on the surface and in solution was explained by the interaction of the adsorbed coumarin organosilane molecules with the hydroxyl groups on the fused silica surface. This interaction produces a perturbation of the π electron distribution and the electronic transitions of the coumarin chromophore of the organosilane molecules adsorbed on the surface. From the kinetics adsorption curves, the calculated enthalpy values of 74.8 ± 5.2 kJ mol -1 and free energy of -38.22 ± 0.70 kJ mol -1 at 23 deg. C indicates a chemisorption process. The high sensitivity of ATR spectroscopy allows the detection of a monolayer formed by a 10 nM concentration of coumarin organosilane molecules, which covers more than half of the maximum surface coverage at 60 deg. C.

  13. Incident laser modulation of a repaired damage site with a rim in fused silica rear subsurface

    International Nuclear Information System (INIS)

    Li Li; Xiang Xia; Zu Xiao-Tao; Yuan Xiao-Dong; He Shao-Bo; Jiang Xiao-Dong; Zheng Wan-Guo

    2012-01-01

    Local CO 2 laser treatment has proved to be an effective method to prevent the 351-nm laser-induced damage sites in a fused silica surface from exponentially growing, which is responsible for limiting the lifetime of optics in high fluence laser systems. However, the CO 2 laser induced ablation crater is often surrounded by a raised rim at the edge, which can also result in the intensification of transmitted ultraviolet light that may damage the downstream optics. In this work, the three-dimensional finite-difference time-domain method is developed to simulate the distribution of electrical field intensity in the vicinity of the CO 2 laser mitigated damage site located in the exit subsurface of fused silica. The simulated results show that the repaired damage sites with raised rims cause more notable modulation to the incident laser than those without rims. Specifically, we present a theoretical model of using dimpled patterning to control the rim structure around the edge of repaired damage sites to avoid damage to downstream optics. The calculated results accord well with previous experimental results and the underlying physical mechanism is analysed in detail. (electromagnetism, optics, acoustics, heat transfer, classical mechanics, and fluid dynamics)

  14. Micro Fluidic Channel Machining on Fused Silica Glass Using Powder Blasting.

    Science.gov (United States)

    Jang, Ho-Su; Cho, Myeong-Woo; Park, Dong-Sam

    2008-02-06

    In this study, micro fluid channels are machined on fused silica glass via powder blasting, a mechanical etching process, and the machining characteristics of the channels are experimentally evaluated. In the process, material removal is performed by the collision of micro abrasives injected by highly compressed air on to the target surface. This approach can be characterized as an integration of brittle mode machining based on micro crack propagation. Fused silica glass, a high purity synthetic amorphous silicon dioxide, is selected as a workpiece material. It has a very low thermal expansion coefficient and excellent optical qualities and exceptional transmittance over a wide spectral range, especially in the ultraviolet range. The powder blasting process parameters affecting the machined results are injection pressure, abrasive particle size and density, stand-off distance, number of nozzle scanning, and shape/size of the required patterns. In this study, the influence of the number of nozzle scanning, abrasive particle size, and pattern size on the formation of micro channels is investigated. Machined shapes and surface roughness are measured using a 3-dimensional vision profiler and the results are discussed.

  15. Micro Fluidic Channel Machining on Fused Silica Glass Using Powder Blasting

    Directory of Open Access Journals (Sweden)

    Dong-Sam Park

    2008-02-01

    Full Text Available In this study, micro fluid channels are machined on fused silica glass via powder blasting, a mechanical etching process, and the machining characteristics of the channels are experimentally evaluated. In the process, material removal is performed by the collision of micro abrasives injected by highly compressed air on to the target surface. This approach can be characterized as an integration of brittle mode machining based on micro crack propagation. Fused silica glass, a high purity synthetic amorphous silicon dioxide, is selected as a workpiece material. It has a very low thermal expansion coefficient and excellent optical qualities and exceptional transmittance over a wide spectral range, especially in the ultraviolet range. The powder blasting process parameters affecting the machined results are injection pressure, abrasive particle size and density, stand-off distance, number of nozzle scanning, and shape/size of the required patterns. In this study, the influence of the number of nozzle scanning, abrasive particle size, and pattern size on the formation of micro channels is investigated. Machined shapes and surface roughness are measured using a 3-dimensional vision profiler and the results are discussed.

  16. Design of polarization-independent transmission fused-silica grating with high diffraction efficiency

    Science.gov (United States)

    Cheng, Yushui; Li, Chaoming; Chen, Xinrong; Yu, Jian; Tang, Yu; Wang, Rui; Xu, Haiyan; Hu, Zuyuan; Wu, Jianhong

    2018-01-01

    The high diffraction efficiency and high dispersion ability of diffraction grating plays a very important role in laser systems. Fused-silica transmission gratings not only have board band, high diffraction efficiency and high damage threshold, but also have the advantage of light path without shelter comparing to reflective gratings. In this paper, the study of polarization-independent transmission fused-silica grating is carried out, and the influence of rectangular and trapezoidal grating microstructures on the -1st diffraction efficiency of grating is analyzed. For trapezoidal groove structure, in the range of 80 to 90 degrees, the distributions of diffraction efficiency at different bottom angle are calculated and analyzed. The structure parameters of the grating are optimized by rigorous coupled wave theory. The designed grating groove density is 1440 lines/mm. The -1st diffraction efficiency of the grating is over 96% for both of TE and TM polarized waves at the Littrow angle (49.7 degrees) with the center wavelength of 1060nm. Within the bandwidth of 42nm (from 1039 to 1081nm), the -1st diffraction efficiency of the designed grating is theoretically greater than 90% for both of TE and TM polarized waves.

  17. Fabrication and Characterization of Linear and Nonlinear Photonic Devices in Fused Silica by Femtosecond Laser Writing

    Science.gov (United States)

    Ng, Jason Clement

    Femtosecond laser processing is a flexible, three-dimensional (3D) fabrication technique used to make integrated low-loss photonic devices in fused silica. My work expanded the suite of available optical devices through the design and optimization of linear optical components such as low-loss (70-nm spectral window. My work further complemented femtosecond laser processing with the development of nonlinear device capabilities. While thermal poling is a well known process, significant challenges had restricted the development of nonlinear devices in fused silica. The laser writing process would erase the induced nonlinearity (erasing) while a written waveguide core acted as a barrier to the thermal poling process (blocking). Using second harmonic (SH) microscopy, the effectiveness of thermal poling on laser-written waveguides was systematically analyzed leading to the technique of "double poling", which effectively overcomes the two challenges of erasing and blocking. In this new process the substrate is poled before and after waveguide writing to restore the induced nonlinearity within the vicinity of the waveguide to enable effective poling for inducing a second-order nonlinearity (SON) in fused silica. A new flexible, femtosecond laser based erasure process was also developed to enable quasi-phase matching and to form arbitrarily chirped gratings. Following this result, second harmonic generation (SHG) in a quasiphase-matched (QPM) femtosecond laser written waveguide device was demonstrated. SHG in a chirped QPM structure was also demonstrated to illustrate the flexibility of the femtosecond laser writing technique. These are the first demonstration of frequency doubling in an all-femtosecond-laser-written structure. A maximum SHG conversion efficiency of 1.3 +/- 0.1x10 -11/W-cm-2 was achieved for the fundamental wavelength of 1552.8 nm with a phase-matching bandwidth of 4.4 nm for a 10.0-mm-long waveguide. For a shorter sample, an effective SON of chi(2) = 0

  18. 3D Multi-Microchannel Helical Mixer Fabricated by Femtosecond Laser inside Fused Silica

    Directory of Open Access Journals (Sweden)

    Chao Shan

    2018-01-01

    Full Text Available Three-dimensional (3D multi-microchannel mixers can meet the requirements of different combinations according to actual needs. Rapid and simple creation of 3D multi-microchannel mixers in a “lab-on-a-chip” platform is a significant challenge in micromachining. In order to realize the complex mixing functions of microfluidic chips, we fabricated two kinds of complex structure micromixers for multiple substance mixes simultaneously, separately, and in proper order. The 3D multi-microchannel mixers are fabricated by femtosecond laser wet etch technology inside fused silica. The 3D multi-microchannel helical mixers have desirable uniformity and consistency, which will greatly expand their utility and scope of application.

  19. Growth of Laser Initiated Damage in Fused Silica at 527 nm

    International Nuclear Information System (INIS)

    Norton, M A; Donohue, E E; Hollingsworth, W G; McElroy, J N; Hackel, R P

    2003-01-01

    The effective lifetime of optics is limited by both laser-induced damage and the subsequent growth of laser initiated damage sites. We have measured the growth rate of laser-induced damage in fused silica in both air and vacuum at 527 nm. For damage on the exit surface, the data shows exponential growth in the lateral size of the damage site with shot number. The exponential growth coefficient depends linearly on the laser fluence. The behavior at the fluence threshold for growth is contrasted to that observed at 351 nm. The growth rate was not significantly affected by either the wavelength of the initiating fluence or the presence of 10 torr of air as compared to vacuum. When the damage is located on the input surface, it has both a higher threshold for growth and does not grow exponentially

  20. Fused silica GRISMs manufactured by hydrophilic direct bonding at moderate heating

    Science.gov (United States)

    Kalkowski, G.; Grabowski, K.; Harnisch, G.; Flügel-Paul, T.; Zeitner, U.; Risse, S.

    2017-12-01

    For high-resolution spectroscopy in space, GRISM elements—obtained by patterning gratings onto a prism surface—find increasing applications. We report on GRISM manufacturing by joining the individual functional elements—prisms and gratings—to suitable components by the technology of hydrophilic direct bonding. Fused silica was used as a substrate material and binary gratings were fabricated by standard e-beam lithography and dry etching. Alignment of the grating dispersion direction to the prism angle was realized by passive adjustment on dedicated bonding gear matched to the substrate geometry. Materials adapted bonds of high transmission, stiffness, and strength were obtained after heat treatment at temperatures of about 200 °C in vacuum. Examples for bonding uncoated as well as coated grating surfaces are given. The results illustrate the great potential of hydrophilic glass direct bonding for manufacturing transmission optics to be used in space or other heavy duty applications.

  1. Disposable Polydimethylsiloxane (PDMS-Coated Fused Silica Optical Fibers for Sampling Pheromones of Moths.

    Directory of Open Access Journals (Sweden)

    Rik Lievers

    Full Text Available In the past decades, the sex pheromone composition in female moths has been analyzed by different methods, ranging from volatile collections to gland extractions, which all have some disadvantage: volatile collections can generally only be conducted on (small groups of females to detect the minor pheromone compounds, whereas gland extractions are destructive. Direct-contact SPME overcomes some of these disadvantages, but is expensive, the SPME fiber coating can be damaged due to repeated usage, and samples need to be analyzed relatively quickly after sampling. In this study, we assessed the suitability of cheap and disposable fused silica optical fibers coated with 100 μm polydimethylsiloxane (PDMS by sampling the pheromone of two noctuid moths, Heliothis virescens and Heliothis subflexa. By rubbing the disposable PDMS fibers over the pheromone glands of females that had called for at least 15 minutes and subsequently extracting the PDMS fibers in hexane, we collected all known pheromone compounds, and we found a strong positive correlation for most pheromone compounds between the disposable PDMS fiber rubs and the corresponding gland extracts of the same females. When comparing this method to volatile collections and the corresponding gland extracts, we generally found comparable percentages between the three techniques, with some differences that likely stem from the chemical properties of the individual pheromone compounds. Hexane extraction of cheap, disposable, PDMS coated fused silica optical fibers allows for sampling large quantities of individual females in a short time, eliminates the need for immediate sample analysis, and enables to use the same sample for multiple chemical analyses.

  2. Preparation of fused-silica columns with phases immobilized by cobalt-60 gamma radiation; application to essential oil analysis

    Energy Technology Data Exchange (ETDEWEB)

    Hubball, J.A.

    1987-01-01

    Cobalt-60 gamma-radiation was used to immobilize polymeric stationary phases in fused silica capillary columns for gas chromatography. Surface studies of the uncoated fused silica tubing by optical and scanning electron microscopy indicated some irregularities, but overall the tubing maintained its strength and flexibility at dosages up to 25 MRads. A polydimethylsiloxane phase (OV-1) and a polyethylene glycol phase (Carbowax 20 M) were effectively immobilized on the inner surface of fused silica capillary tubing without altering the properties of the phases. The optimum radiation dosage for OV-1 was 7 MRads, while Carbowax 20 M required 25 MRads to immobilize 33% of the coated layer. Fused silica capillary columns prepared with both phases were evaluated for deactivation, efficiency, and thermal stability. Immobilization of Carbowax 20 M extended the low and high temperature limits by 30 C in each direction. Columns prepared in this study were used to analyze the essential oil of Siparuna guianensis. Several key components of the oil were identified by GC/MS and gas chromatographic techniques.

  3. Analysis of polycyclic aromatic hydrocarbons I. Determination by gas chromatography with glass and fused silica capillary columns

    International Nuclear Information System (INIS)

    Perez, M. M.; Gonzalez, D.

    1987-01-01

    A study of the analysis by gas chromatography of aromatic polycyclic hydrocarbons is presented. The separation has been carried out by glass and fused silica capillary column. The limitations and the advantages of the procedure are discussed in terms of separation efficiency, sensitivity and precision. (Author) 17 refs

  4. Optical and electrical properties of boron doped diamond thin conductive films deposited on fused silica glass substrates

    Energy Technology Data Exchange (ETDEWEB)

    Ficek, M.; Sobaszek, M.; Gnyba, M. [Department of Metrology and Optoelectronics, Gdansk University of Technology, 11/12G. Narutowicza St., 80-233 Gdansk (Poland); Ryl, J. [Department of Electrochemistry, Corrosion and Material Engineering, Gdansk University of Technology, 11/12 Narutowicza St., 80-233 Gdansk (Poland); Gołuński, Ł. [Department of Metrology and Optoelectronics, Gdansk University of Technology, 11/12G. Narutowicza St., 80-233 Gdansk (Poland); Smietana, M.; Jasiński, J. [Institute of Microelectronics and Optoelectronics, Warsaw University of Technology, 75 Koszykowa St., 00-662 Warsaw (Poland); Caban, P. [Institute of Electronic Materials Technology, 133 Wolczynska St., 01-919 Warsaw (Poland); Bogdanowicz, R., E-mail: rbogdan@eti.pg.gda.pl [Department of Metrology and Optoelectronics, Gdansk University of Technology, 11/12G. Narutowicza St., 80-233 Gdansk (Poland); Materials and Process Simulation Center, California Institute of Technology, Pasadena, CA 91125 (United States)

    2016-11-30

    Highlights: • Growth of 60% of transmittance diamond films with resistivity as low as 48 Ω cm. • Two step seeding process of fused silica: plasma hydrogenation and wet seeding. • Nanodiamond seeding density of 2 × 10{sup 10} cm{sup −2} at fused silica substrates. • High refractive index (2.4 @550 nm) was achieved for BDD films deposited at 500 °C. - Abstract: This paper presents boron-doped diamond (BDD) film as a conductive coating for optical and electronic purposes. Seeding and growth processes of thin diamond films on fused silica have been investigated. Growth processes of thin diamond films on fused silica were investigated at various boron doping level and methane admixture. Two step pre-treatment procedure of fused silica substrate was applied to achieve high seeding density. First, the substrates undergo the hydrogen plasma treatment then spin-coating seeding using a dispersion consisting of detonation nanodiamond in dimethyl sulfoxide with polyvinyl alcohol was applied. Such an approach results in seeding density of 2 × 10{sup 10} cm{sup −2}. The scanning electron microscopy images showed homogenous, continuous and polycrystalline surface morphology with minimal grain size of 200 nm for highly boron doped films. The sp{sup 3}/sp{sup 2} ratio was calculated using Raman spectra deconvolution method. A high refractive index (range of 2.0–2.4 @550 nm) was achieved for BDD films deposited at 500 °C. The values of extinction coefficient were below 0.1 at λ = 550 nm, indicating low absorption of the film. The fabricated BDD thin films displayed resistivity below 48 Ohm cm and transmittance over 60% in the visible wavelength range.

  5. Determination of diffusion coefficients of hydrogen in fused silica between 296 and 523 K by Raman spectroscopy and application of fused silica capillaries in studying redox reactions

    Science.gov (United States)

    Shang, L.; Chou, I-Ming; Lu, W.; Burruss, Robert; Zhang, Y.

    2009-01-01

    Diffusion coefficients (D) of hydrogen in fused silica capillaries (FSC) were determined between 296 and 523 K by Raman spectroscopy using CO2 as an internal standard. FSC capsules (3.25 × 10−4 m OD, 9.9 × 10−5 m ID, and ∼0.01 m long) containing CO2 and H2were prepared and the initial relative concentrations of hydrogen in these capsules were derived from the Raman peak-height ratios between H2 (near 587 cm−1) and CO2 (near 1387 cm−1). The sample capsules were then heated at a fixed temperature (T) at one atmosphere to let H2 diffuse out of the capsule, and the changes of hydrogen concentration were monitored by Raman spectroscopy after quench. This process was repeated using different heating durations at 296 (room T), 323, 375, 430, 473, and 523 K; the same sample capsule was used repeatedly at each temperature. The values of D (in m2 s−1) in FSC were obtained by fitting the observed changes of hydrogen concentration in the FSC capsule to an equation based on Fick’s law. Our D values are in good agreement with the more recent of the two previously reported experimental data sets, and both can be represented by:lnD=-(16.471±0.035)-44589±139RT(R2=0.99991)">lnD=-(16.471±0.035)-44589±139RT(R2=0.99991)where R is the gas constant (8.3145 J/mol K), T in Kelvin, and errors at 1σ level. The slope corresponds to an activation energy of 44.59 ± 0.14 kJ/mol.The D in FSC determined at 296 K is about an order of magnitude higher than that in platinum at 723 K, indicating that FSC is a suitable membrane for hydrogen at temperature between 673 K and room temperature, and has a great potential for studying redox reactions at these temperatures, especially for systems containing organic material and/or sulphur.

  6. Fabrication of an ordered mesoporous nanoparticle SiO2/Mc and their CMP of fused silica application

    Science.gov (United States)

    Xu, L.; Zou, C. L.; Zhang, X.; Kang, C. X.; Luo, G. H.; Pan, G. S.

    2018-02-01

    Here we developed an inorganic SiO2 core/mesoporous carbon shell structured (SiO2/Mc) nano-composite particle with an average size ∼50 nm as abrasives with improved dispersibility and distribution via a hydro-thermal route to obtain reserved fused silica surface and subsurface. The obtained SiO2/Mc were characterized by scanning electronic microscope. Atomic force microscopy was used to assess the surface before and after planarization. The results indicated the as-prepared SiO2/Mc composite abrasives gave a much lower surface roughness as well as lower topographical variations than that of traditional colloidal silica abrasives.

  7. Evaluation of the fused silica thermal conductivity by comparing infrared thermometry measurements with two-dimensional simulations

    International Nuclear Information System (INIS)

    Combis, Patrick; Cormont, Philippe; Hebert, David; Robin, Lucile; Rullier, Jean-Luc; Gallais, Laurent

    2012-01-01

    A self-consistent approach is proposed to determine the temperature dependent thermal conductivity k(T) of fused silica, for a range of temperatures up to material evaporation using a CO 2 laser irradiation. Calculation of the temperature of silica using a two-dimensional axi-symmetric code was linked step by step as the laser power was increased with experimental measurements using infrared thermography. We show that previously reported k(T) does not reproduce the temporal profile as well as our adaptive fit which shows that k(T) evolves with slope discontinuities at the annealing temperature and the softening temperature.

  8. Influence of secondary treatment with CO2 laser irradiation for mitigation site on fused silica surface

    Science.gov (United States)

    Jiang, Yong; Zhou, Qiang; Qiu, Rong; Gao, Xiang; Wang, Hui-Li; Yao, Cai-Zhen; Wang, Jun-Bo; Zhao, Xin; Liu, Chun-Ming; Xiang, Xia; Zu, Xiao-Tao; Yuan, Xiao-Dong; Miao, Xin-Xiang

    2016-10-01

    The ablation debris and raised rim, as well as residual stress and deep crater will be formed during the mitigation of damage site with a CO2 laser irradiation on fused silica surface, which greatly affects the laser damage resistance of optics. In this study, the experimental study combined with numerical simulation is utilized to investigate the effect of the secondary treatment on a mitigated site by CO2 laser irradiation. The results indicate that the ablation debris and the raised rim can be completely eliminated and the depth of crater can be reduced. Notable results show that the residual stress of the mitigation site after treatment will reduce two-thirds of the original stress. Finally, the elimination and the controlling mechanism of secondary treatment on the debris and raised rim, as well as the reasons for changing the profile and stress are analyzed. The results can provide a reference for the optimization treatment of mitigation sites by CO2 laser secondary treatment. Project supported by the National Natural Science Foundation of China (Grant Nos. 61505170, 61505171, and 51535003), the Joint Fund of the National Natural Science Foundation of China, the Chinese Academy of Engineering Physics (Grant No. U1530109), and the China Postdoctoral Science Foundation (Grant No. 2016M592709).

  9. Generation of microstripe cylindrical and toroidal mirrors by localized laser evaporation of fused silica.

    Science.gov (United States)

    Wlodarczyk, Krystian L; Thomson, Ian J; Baker, Howard J; Hall, Denis R

    2012-09-10

    We report a new technique for the rapid fabrication of microstripe cylindrical and toroidal mirrors with a high ratio (>10) of the two principal radii of curvature (RoC(1)/RoC(2)), and demonstrate their effectiveness as mode-selecting resonator mirrors for high-power planar waveguide lasers. In this process, the larger radius of curvature (RoC(1)) is determined by the planar or cylindrical shape of the fused silica substrate selected for laser processing, whilst the other (RoC(2)) is produced by controlled CO(2) laser-induced vaporization of the glass. The narrow stripe mirror aperture is achieved by applying a set of partially overlapped laser scans, with the incident laser power, the number of laser scans, and their spacing being used to control the curvature produced by laser evaporation. In this work, a 1 mm diameter laser spot is used to produce grooves of cylindrical/toroidal shape with 240 μm width and 16 mm length. After high reflectance coating, these grooves are found to provide excellent mode selectivity as resonator mirrors for a 150 μm core Yb:YAG planar waveguide laser, producing high brightness output at more than 300 W. The results show clearly that the laser-generated microstripe mirrors can improve the optical performance of high-power planar waveguide lasers when applied in a low-loss mode-selective resonator configuration.

  10. Two-photon induced fluorescence and other optical effects in irradiated and doped fused silica

    Energy Technology Data Exchange (ETDEWEB)

    Kramer, S.D.

    1986-07-01

    The objective of this program was to assess and identify irradiation techniques which could be used to modify the optical charactistics of doped fused silica. Primary emphasis was placed on determining if gamma ray or neutron bombardment of the glass would enhance certain Raman and nonlinear optical effects. In particular, the effect of irradiation on optical two photon induced fluorescence was studied in detail. The maximum radiation exposures used were 10/sup 6/ rads (Si) of gamma rays and neutron fluences of 1 x 10/sup 14/ neutrons/cm/sup 2/. The optical measurements were made at room temperature between one and four months after irradiation. The maximum input light intensity was 10/sup 9/ watts/cm/sup 2/ at a near infrared (1.06 ..mu..) input wavelength which was chosen to lie in a transparent spectral region of the glass. Under these experimental conditions a careful search revealed no detectable two-photon induced fluorescence in the region from 550 to 900 nm. The upper limit for the photon efficiency of this process was determined to be less than 1 x 10/sup -10/%. 89 refs., 12 figs.

  11. Two-photon induced fluorescence and other optical effects in irradiated and doped fused silica

    International Nuclear Information System (INIS)

    Kramer, S.D.

    1986-07-01

    The objective of this program was to assess and identify irradiation techniques which could be used to modify the optical charactistics of doped fused silica. Primary emphasis was placed on determining if gamma ray or neutron bombardment of the glass would enhance certain Raman and nonlinear optical effects. In particular, the effect of irradiation on optical two photon induced fluorescence was studied in detail. The maximum radiation exposures used were 10 6 rads (Si) of gamma rays and neutron fluences of 1 x 10 14 neutrons/cm 2 . The optical measurements were made at room temperature between one and four months after irradiation. The maximum input light intensity was 10 9 watts/cm 2 at a near infrared (1.06 μ) input wavelength which was chosen to lie in a transparent spectral region of the glass. Under these experimental conditions a careful search revealed no detectable two-photon induced fluorescence in the region from 550 to 900 nm. The upper limit for the photon efficiency of this process was determined to be less than 1 x 10 -10 %. 89 refs., 12 figs

  12. Examination of Relationship Between Photonic Signatures and Fracture Strength of Fused Silica Used in Orbiter Windows

    Science.gov (United States)

    Yost, William T.; Cramer, K. Elliott; Estes, Linda R.; Salem, Jonathan A.; Lankford, James, Jr.; Lesniak, Jon

    2011-01-01

    A commercially available grey-field polariscope (GFP) instrument for photoelastic examination is used to assess impact damage inflicted upon the outermost pane of the orbiter windows. Four categories of damage: hyper-velocity impacts that occur during space-flight (HVI); hypervelocity impacts artificially made at the Hypervelocity Impact Technology Facility (HIT-F); impacts made by larger objects falling onto the pane surface to simulate dropped items on the window during service/storage of vehicle (Bruises); and light scratches from dull objects designed to mimic those that might occur by dragging a dull object across the glass surface (Chatter Checks) are examined. The damage sites are cored from fused silica window carcasses, examined with the GFP and other methodologies, and broken using the ASTM Standard C1499-09 to measure the fracture strength. A correlation is made between the fracture strength and damage-site measurements including geometrical measurements and GFP measurements of photoelastic retardation (stress patterns) surrounding the damage sites. An analytical damage model to predict fracture strength from photoelastic retardation measurements is presented and compared with experimental results.

  13. Low-temperature vibrational dynamics of fused silica and binary silicate glasses

    Science.gov (United States)

    Cai, Ling; Shi, Ying; Hrdina, Ken; Moore, Lisa; Wu, Jingshi; Daemen, Luke L.; Cheng, Yongqiang

    2018-02-01

    Inelastic neutron scattering was used to study the vibrational dynamics of fused silica and its mixed binary glasses that were doped with either TiO2 or K2O . The energy transfer was measured from zero to 180 meV where the so-called Boson peaks (BP) at low energy and molecular vibrations at high energy are included. Although most of the vibrational spectra at the high energy resemble those reported in earlier literature, a defect-mode-like peak is observed for the doped binary systems near 120 meV . At very low temperature, the BP intensity increases rapidly with temperature and then, at higher temperature, the peak intensity decreases. As a result, a maximum is observed in the temperature dependence of the BP intensity. This maximum was shown in all four samples, but the pure SiO2 sample shows the highest intensity peak and the lowest temperature for peak position. Broadband energy spectra reveal a shift of intensity from BP to the more localized modes at higher energy. Temperature evolution of BP and its relationship with heat conduction and thermal expansion are discussed.

  14. Fracture Strength of Fused Silica From Photonic Signatures Around Collision Sites

    Science.gov (United States)

    Yost, William T.; Cramer, K Elliott

    2015-01-01

    Impact sites in glass affect its fracture strength. An analytical model that predicts fracture strength from grey-field polariscope (GFP) readings (photoelastic retardations) has been developed and reported in the literature. The model is suggestive that stress fields, resulting from impact damage, destablizes sites within the glass, which lead to pathways that cause strength degradation. Using data collected from fused silica specimens fabricated from outer window panes that were designed for the space shuttle, the model was tested against four categories of inflicted damage. The damage sites were cored from the window carcasses, examined with the GFP and broken using the ASTM Standard C1499-09 to measure the fracture strength. A correlation is made between the fracture strength and the photoelastic retardation measured at the damage site in each specimen. A least-squares fit is calculated. The results are compared with the predictions from the model. A plausible single-sided NDE damage site inspection method (a version of which is planned for glass inspection in the Orion Project) that relates photoelastic retardation in glass components to its fracture strength is presented.

  15. An AC phase measuring interferometer for measuring dn/dT of fused silica and calcium fluoride at 193 nm

    Energy Technology Data Exchange (ETDEWEB)

    Shagam, R.N.

    1998-09-01

    A novel method for the measurement of the change in index of refraction vs. temperature (dn/dT) of fused silica and calcium fluoride at the 193 nm wavelength has been developed in support of thermal modeling efforts for the development of 193 nm-based photolithographic exposure tools. The method, based upon grating lateral shear interferometry, uses a transmissive linear grating to divide a 193 nm laser beam into several beam paths by diffraction which propagate through separate identical material samples. One diffracted order passing through one sample overlaps the undiffracted beam from a second sample and forms interference fringes dependent upon the optical path difference between the two samples. Optical phase delay due to an index change from heating one of the samples causes the interference fringes to change sinusoidally with phase. The interferometer also makes use of AC phase measurement techniques through lateral translation of the grating. Results for several samples of fused silica and calcium fluoride are demonstrated.

  16. Hydrolysis of polycarbonate in sub-critical water in fused silica capillary reactor with in situ Raman spectroscopy

    Science.gov (United States)

    Pan, Z.; Chou, I-Ming; Burruss, R.C.

    2009-01-01

    The advantages of using fused silica capillary reactor (FSCR) instead of conventional autoclave for studying chemical reactions at elevated pressure and temperature conditions were demonstrated in this study, including the allowance for visual observation under a microscope and in situ Raman spectroscopic characterization of polycarbonate and coexisting phases during hydrolysis in subcritical water.

  17. Fabrication of Through via Holes in Ultra-Thin Fused Silica Wafers for Microwave and Millimeter-Wave Applications

    Directory of Open Access Journals (Sweden)

    Xiao Li

    2018-03-01

    Full Text Available Through via holes in fused silica are a key infrastructure element of microwave and millimeter-wave circuits and 3D integration. In this work, etching through via holes in ultra-thin fused silica wafers using deep reactive-ion etching (DRIE and laser ablation was developed and analyzed. The experimental setup and process parameters for both methods are presented and compared. For DRIE, three types of mask materials including KMPR 1035 (Nippon Kayaku, Tokyo, Japan photoresist, amorphous silicon and chromium—with their corresponding optimized processing recipes—were tested, aiming at etching through a 100 μm fused silica wafer. From the experiments, we concluded that using chromium as the masking material is the best choice when using DRIE. However, we found that the laser ablation method with a laser pulse fluence of 2.89 J/cm2 and a pulse overlap of 91% has advantages over DRIE. The laser ablation method has a simpler process complexity, while offering a fair etching result. In particular, the sidewall profile angle is measured to be 75° to the bottom surface of the wafer, which is ideal for the subsequent metallization process. As a demonstration, a two-inch wafer with 624 via holes was processed using both technologies, and the laser ablation method showed better efficiency compared to DRIE.

  18. Damage and fracture in large aperture, fused silica, vacuum spatial filter lenses

    International Nuclear Information System (INIS)

    Campbell, J.H.; Edwards, G.J.; Marion, J.E.

    1995-01-01

    Optical damage that results in large scale fracture has been observed in the large, high-fluence, fused-silica, spatial filter lenses on the Nova and Beamlet lasers. In nearly all cases damage occurs on the vacuum side of the lenses and because the vacuum side of the lens is under tensile stress this damage can lead to catastrophic crack growth if the flaw (damage) size exceeds the critical flaw size for SiO 2 . The damaged 52 cm Nova lenses fracture into two and sometimes three large pieces. Although under full vacuum load at the time they fracture, the Nova lenses do not implode. Rather the authors have observed that the pieces lock together and air slowly leaks into the vacuum spatial filter housing through the lens cracks. The Beamlet lenses have a larger aspect ratio and peak tensile stress than Nova. The peak tensile stress at the center of the output surface of the Beamlet lens is 1,490 psi versus 810 psi for Nova. During a recent Beamlet high energy shot, a damage spot on the lens grew to the critical flaw size and the lens imploded. Post shot data indicate the lens probably fractured into 5 to 7 pieces, however, unlike Nova, these pieces did not lock together. Analysis shows that the likely source of damage is contamination from pinhole blow-off or out-gassing of volatile materials within the spatial filter. Contamination degrades the antireflection properties of the sol-gel coating and reduces its damage threshold. By changing the design of the Beamlet lens it may be possible to insure that it fails safe by locking up in much that same manner as the Nova lens

  19. Structural changes in irreversibly densified fused silica: implications for the chemical resistance of high level nuclear waste glasses

    International Nuclear Information System (INIS)

    Susman, S.; Volin, K.J.; Liebermann, R.C.; Gwanmesia, G.D.; Yanbin Wang

    1990-01-01

    Energetic photons and energetic particles create changes in the structure of nuclear waste glasses. These can be observed as changes in the average bulk physical properties. For example, exposure of fused silica to high doses of neutron bombardment leads to a maximum average compaction of 3%. However, this does not reveal the true extent of the densification that takes place at a microscopic level. Recent advances in high pressure technology have yielded large samples of fused silica which have been permanently densified under pressure and whose bulk density has been increased by 20%. These specimens have an overall structure that replicates the microstructure of a radiation damaged glass. Measurements have been made for the first time of the structural changes in this pressure densified vitreous silica using neutron diffraction and infrared absorption spectrometry. Extensive alterations in intermediate range order have been observed with consequent anticipated changes in chemical reactivity. The resistance of high level waste glasses to leaching by groundwater must be considered in light of these experimental findings. (author)

  20. In-situ monitoring of surface post-processing in large aperture fused silica optics with Optical Coherence Tomography

    Energy Technology Data Exchange (ETDEWEB)

    Guss, G M; Bass, I l; Hackel, R P; Mailhiot, C; Demos, S G

    2008-02-08

    Optical Coherence Tomography is explored as a method to image laser-damage sites located on the surface of large aperture fused silica optics during post-processing via CO{sub 2} laser ablation. The signal analysis for image acquisition was adapted to meet the sensitivity requirements for this application. A long-working distance geometry was employed to allow imaging through the opposite surface of the 5-cm thick optic. The experimental results demonstrate the potential of OCT for remote monitoring of transparent material processing applications.

  1. Full-Stokes polarization imaging method based on the self-organized grating array in fused silica.

    Science.gov (United States)

    Xu, Canhua; Ke, Chaozhen; Ma, Jing; Huang, Yantang; Zeng, Zhiping

    2018-02-05

    A full-Stokes polarization imaging method based on the self-organized grating array was presented. By focusing the ultra-fast laser with moderate fluence into fused silica, the self-organized grating array was fabricated, featuring the optical properties similar to wave plates. A set of four independent polarization measurements were simultaneously acquired with designed grating array mounted in the focal plane of an imaging detector. Experimental results including the device fabrication, calibration and optimization were presented. Finally, a principle verification experiment was implemented for our polarization imaging method.

  2. Fabrication of BCP/Silica Scaffolds with Dual-Pore by Combining Fused Deposition Modeling and the Particle Leaching Method

    Energy Technology Data Exchange (ETDEWEB)

    Sa, Min-Woo; Kim, Jong Young [Andong National Univ., Andong (Korea, Republic of)

    2016-10-15

    In recent years, traditional scaffold fabrication techniques such as gas foaming, salt leaching, sponge replica, and freeze casting in tissue engineering have significantly limited sufficient mechanical property and cell interaction effect due to only random pores. Fused deposition modeling is the most apposite technology for fabricating the 3D scaffolds using the polymeric materials in tissue engineering application. In this study, 3D slurry mould was fabricated with a blended biphasic calcium phosphate (BCP)/Silica/Alginic acid sodium salt slurry in PCL mould and heated for two hours at 100 .deg. C to harden the blended slurry. 3D dual-pore BCP/Silica scaffold, composed of macro pores interconnected with micro pores, was successfully fabricated by sintering at furnace of 1100 .deg. C. Surface morphology and 3D shape of dual-pore BCP/Silica scaffold from scanning electron microscopy were observed. Also, the mechanical properties of 3D BCP/Silica scaffold, according to blending ratio of alginic acid sodium salt, were evaluated through compression test.

  3. A hybrid concept (segmented plus monolithic fused silica shells) for a high-throughput and high-angular resolution x-ray mission (Lynx/X-Ray Surveyor like)

    Science.gov (United States)

    Basso, Stefano; Civitani, Marta; Pareschi, Giovanni; Parodi, Giancarlo

    2017-09-01

    Lynx is a large area and high angular resolution X-ray mission being studied by NASA to be presented to the next Decadal Survey for the implementation in the next decade. It aims to realize an X-ray telescope with the effective area similar to Athena (2 m2 at 1 keV) but with the same angular resolution of Chandra and a much larger Field Of View (up 20 arcmin x 20 arcmin). The science of X-ray Surveyor requires a large-throughput mirror assembly with sub-arcsec angular resolution. These future X-ray mirrors have a set of requirements which, collectively, represents very substantial advances over any currently in operation or planned for missions other than X-ray Surveyor. Of particular importance is achieving low mass per unit collecting area, while maintaining Chandra like angular resolution. Among the possible solutions under study, the direct polishing of both thin monolithic pseudo-cylindrical shells and segments made of fused silica are being considered as viable solutions for the implementation of the mirrors. Fused silica has very good thermomechanical parameters (including a very low CTE), making the material particularly well suited for for the production of the Lynx mirrors. It should be noted that the use of close shells is also very attractive, since the operations for the integration of the shells will be greatly simplified and the area lost due to the vignetting from the interfacing structures minimized even if the management of such big (diameter of 3 m) and thin shells have to be demonstrated. In this paper we will discuss a possible basic layout for a full shell mirror and a hybrid concept (segmented plus monolithic shells made of fused silica) as a second solution, for the Lynx/XRS telescope, discussing preliminary results in terms of optical and mechanical performance.

  4. Experimental Investigation on Cutting Characteristics in Nanometric Plunge-Cutting of BK7 and Fused Silica Glasses.

    Science.gov (United States)

    An, Qinglong; Ming, Weiwei; Chen, Ming

    2015-03-27

    Ductile cutting are most widely used in fabricating high-quality optical glass components to achieve crack-free surfaces. For ultra-precision machining of brittle glass materials, critical undeformed chip thickness (CUCT) commonly plays a pivotal role in determining the transition point from ductile cutting to brittle cutting. In this research, cutting characteristics in nanometric cutting of BK7 and fused silica glasses, including machined surface morphology, surface roughness, cutting force and specific cutting energy, were investigated with nanometric plunge-cutting experiments. The same cutting speed of 300 mm/min was used in the experiments with single-crystal diamond tool. CUCT was determined according to the mentioned cutting characteristics. The results revealed that 320 nm was found as the CUCT in BK7 cutting and 50 nm was determined as the size effect of undeformed chip thickness. A high-quality machined surface could be obtained with the undeformed chip thickness between 50 and 320 nm at ductile cutting stage. Moreover, no CUCT was identified in fused silica cutting with the current cutting conditions, and brittle-fracture mechanism was confirmed as the predominant chip-separation mode throughout the nanometric cutting operation.

  5. Laser-induced damage of fused silica at 355 and 1065 nm initiated at aluminum contamination particles on the surface

    International Nuclear Information System (INIS)

    Genin, F.Y.; Michlitsch, K.; Furr, J.; Kozlowski, M.R.; Krulevitch, P.

    1997-01-01

    1-μm thick circular dots, 10-250 μm dia, were deposited onto 1.14 cm thick fused silica windows by sputtering Al through a mask. Al shavings were also deposited on the windows to investigate effects of particle-substrate adhesion. The silica windows were then illuminated repetitively using a 3-ns, 355 nm and an 8.6-ns, 1064 nm laser. The tests were conducted at near normal incidence with particles on input and output surfaces of the windows. During the first shot, a plasma ignited at the metal particle and damage initiated on the fused silica surface. The morphology of the damage at the metal dots were reproducible but different for input and output surface contamination. For input surface contamination, minor damage occurred where the particle was located; such damage ceased to grow with the removal of contaminant material. More serious damage (pits and cracks) was initiated on the output surface (especially at 355 nm) and grew to catastrophic proportions after few shots. Output surface contaminants were usually ejected on the initial shot, leaving a wave pattern on the surface. No further damage occurred with subsequent shots unless a shot (usually the first shot) cracked the surface; such behavior was mostly observed at 355 nm and occasionally for large shavings at 1064 nm. The size of the damaged area scaled with the size of the particle (except when catastrophic damage occurred). Onset of catastrophic damage on output surface occurred only when particles exceeded a critical size. Damage behavior of the sputtered dots was found to be qualitatively similar to that of the shavings. The artificial contamination technique accelerated the study by allowing better control of the test conditions

  6. Effect of a core-softened O-O interatomic interaction on the shock compression of fused silica

    Science.gov (United States)

    Izvekov, Sergei; Weingarten, N. Scott; Byrd, Edward F. C.

    2018-03-01

    Isotropic soft-core potentials have attracted considerable attention due to their ability to reproduce thermodynamic, dynamic, and structural anomalies observed in tetrahedral network-forming compounds such as water and silica. The aim of the present work is to assess the relevance of effective core-softening pertinent to the oxygen-oxygen interaction in silica to the thermodynamics and phase change mechanisms that occur in shock compressed fused silica. We utilize the MD simulation method with a recently published numerical interatomic potential derived from an ab initio MD simulation of liquid silica via force-matching. The resulting potential indicates an effective shoulder-like core-softening of the oxygen-oxygen repulsion. To better understand the role of the core-softening we analyze two derivative force-matching potentials in which the soft-core is replaced with a repulsive core either in the three-body potential term or in all the potential terms. Our analysis is further augmented by a comparison with several popular empirical models for silica that lack an explicit core-softening. The first outstanding feature of shock compressed glass reproduced with the soft-core models but not with the other models is that the shock compression values at pressures above 20 GPa are larger than those observed under hydrostatic compression (an anomalous shock Hugoniot densification). Our calculations indicate the occurrence of a phase transformation along the shock Hugoniot that we link to the O-O repulsion core-softening. The phase transformation is associated with a Hugoniot temperature reversal similar to that observed experimentally. With the soft-core models, the phase change is an isostructural transformation between amorphous polymorphs with no associated melting event. We further examine the nature of the structural transformation by comparing it to the Hugoniot calculations for stishovite. For stishovite, the Hugoniot exhibits temperature reversal and associated

  7. Comparison of laser-based mitigation of fused silica surface damage using mid- versus far-infrared lasers

    Energy Technology Data Exchange (ETDEWEB)

    Yang, S T; Matthews, M J; Elhadj, S; Cooke, D; Guss, G M; Draggoo, V G; Wegner, P J

    2009-12-16

    Laser induced growth of optical damage can limit component lifetime and therefore operating costs of large-aperture fusion-class laser systems. While far-infrared (IR) lasers have been used previously to treat laser damage on fused silica optics and render it benign, little is known about the effectiveness of less-absorbing mid-IR lasers for this purpose. In this study, they quantitatively compare the effectiveness and efficiency of mid-IR (4.6 {micro}m) versus far-IR (10.6 {micro}m) lasers in mitigating damage growth on fused silica surfaces. The non-linear volumetric heating due to mid-IR laser absorption is analyzed by solving the heat equation numerically, taking into account the temperature-dependent absorption coefficient {alpha}(T) at {lambda} = 4.6 {micro}m, while far-IR laser heating is well-described by a linear analytic approximation to the laser-driven temperature rise. In both cases, the predicted results agree well with surface temperature measurements based on infrared radiometry, as well as sub-surface fictive temperature measurements based on confocal Raman microscopy. Damage mitigation efficiency is assessed using a figure of merit (FOM) relating the crack healing depth to laser power required, under minimally-ablative conditions. Based on their FOM, they show that for cracks up to at least 500 {micro}m in depth, mitigation with a 4.6 {micro}m mid-IR laser is more efficient than mitigation with a 10.6 {micro}m far-IR laser. This conclusion is corroborated by direct application of each laser system to the mitigation of pulsed laser-induced damage possessing fractures up to 225 {micro}m in depth.

  8. Thermo-mechanical simulations of CO{sub 2} laser–fused silica interactions

    Energy Technology Data Exchange (ETDEWEB)

    Doualle, T.; Gallais, L., E-mail: laurent.gallais@fresnel.fr [Aix-Marseille Université, CNRS, Centrale Marseille, Institut Fresnel UMR 7249, 13013 Marseille (France); Cormont, P.; Hébert, D.; Rullier, J.-L. [CEA-CESTA, 15 Avenue des Sablières, CS 60001, F33116 Le Barp Cedex (France); Combis, P. [CEA DAM Ile-de-France, F-91297 Arpajon (France)

    2016-03-21

    CO{sub 2} laser heating of silica glass is used in many scientific and industrial applications. Particularly, localized CO{sub 2} laser heating of silica glass has demonstrated its ability to mitigate surface damage on optics used for high power laser applications. To develop such applications, the control of temperature, heat affected area, and resulting mechanical stresses are critical. Therefore, it is necessary to understand the silica transformation, the material ejection, and the thermo-mechanical stresses induced by the laser heating and subsequent cooling. In this paper, we detail the development of comprehensive thermo-mechanical numerical simulations of these physical processes, based on finite-element method. The approach is developed for 2D or 3D cases to tackle the case of a moving beam at the surface of the sample, and we particularly discuss the choice of the different parameters based on bibliographic inputs. The thermal and mechanical numerical results have been compared to different dedicated experimental studies: infrared thermography measurements at the surface of the irradiated area, optical profilometry measurements of the laser-processed sites, and photo-elastic measurements. Very consistent results are obtained between numerical and experimental results for the description of the temperature gradients, the material ejection, and the residual stresses.

  9. Micromanufacturing in Fused Silica via Femtosecond Laser Irradiation Followed by Gas-Phase Chemical Etching

    Directory of Open Access Journals (Sweden)

    Walter Navarrini

    2012-09-01

    Full Text Available Femtosecond laser irradiation followed by chemical etching (FLICE with hydrogen fluoride (HF is an emerging technique for the fabrication of directly buried, three-dimensional microfluidic channels in silica. The procedure, as described in literature, consists of irradiating a silica slab followed by chemical etching using hydrogen fluoride. With aqueous HF the etching process is diffusion-limited and is self-terminating, leading to maximum microchannel lengths of about 1.5 mm, while the use of low-pressure gaseous HF etchant can quickly produce 3 mm long channels with an aspect ratio (Length/Diameter higher than 25. By utilizing this methodology the aspect ratio is not constant, but depends on the length of the channel. When the microchannel is short the aspect ratio increases quickly until it reaches a maximum length at around 1400 µm. Thereafter the aspect ratio starts to decrease slowly. In this paper we present a variation of the low-pressure gaseous HF etching method, which is based on the dynamic displacement of the etchant. This method results in a 13% increase in the aspect ratio (L/D = 29 at the expense of a low etching speed (4 µm/min.

  10. Comparing the use of 4.6 um lasers versus 10.6 um lasers for mitigating damage site growth on fused silica surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Yang, S T; Matthews, M J; Elhadj, S; Cooke, D; Guss, G M; Draggoo, V G; Wegner, P J

    2010-10-21

    The advantage of using mid-infrared (IR) 4.6 {micro}m lasers, versus far-infrared 10.6 {micro}m lasers, for mitigating damage growth on fused silica is investigated. In contrast to fused silica's high absorption at 10.6 {micro}m, silica absorption at 4.6 {micro}m is two orders of magnitude less. The much reduced absorption at 4.6 {micro}m enables deep heat penetration into fused silica when it is heated using the mid-IR laser, which in turn leads to more effective mitigation of damage sites with deep cracks. The advantage of using mid-IR versus far-IR laser for damage growth mitigation under non-evaporative condition is quantified by defining a figure of merit (FOM) that relates the crack healing depth to laser power required. Based on our FOM, we show that for damage cracks up to at least 500 {micro}m in depth, mitigation using a 4.6 {micro}m mid-IR laser is more efficient than mitigation using a 10.6 {micro}m far-IR laser.

  11. Photochemical adhesion of fused silica optical elements with no adhesive strain

    Science.gov (United States)

    Murahara, Masataka; Funatsu, Takayuki; Okamoto, Yoshiaki

    2007-01-01

    An adhesive method that creates properties of heatproof, waterproof, and transparent to ultraviolet ray of 200 nm and under in the wavelength without adhesive strain was developed by putting one silica glass to another with the silicone oil that had been photo-oxidized by Xe2 excimer lamp. The measurement by the ZYGO interferometer showed that there was neither adhesive strain nor bubbles, and the bonding strength of 18MPa was achieved. To compare the heat resistance of the photo-oxidized silicone oil with that of general-purpose adhesives such as silicone rubber, water glass, and epoxy resin, the shearing tensile strength test was conducted after exposing at high temperatures from 25 to 500 °C. As a result, the silicone rubber adhesive exfoliated at 110 °C, and the epoxy resin adhesive, at 150 °C however, the photo-oxidized silicone oil had the bonding strength of 6.5MPa at 500 °C.

  12. A Spectroscopic Comparison of Femtosecond Laser Modified Fused Silica using kHz and MHz Laser Systems.

    Energy Technology Data Exchange (ETDEWEB)

    Reichman, W J; Krol, D M; Shah, L; Yoshino, F; Arai, A; Eaton, S M; Herman, P R

    2005-09-29

    Waveguides were written in fused silica using both a femtosecond fiber laser with a 1 MHz pulse repetition rate and a femtosecond amplified Ti:sapphire laser with a 1 kHz repetition rate. Confocal Raman and fluorescence microscopy were used to study structural changes in the waveguides written with both systems. A broad fluorescence band, centered at 650 nm, associated with non-bridging oxygen hole center (NBOHC) defects was observed after waveguide fabrication with the MHz laser. With the kHz laser system these defects were only observed for pulse energies above 1 {mu}J. Far fewer NBOHC defects were formed with the MHz laser than with kHz writing, possibly due to thermal annealing driven by heat accumulation effects at 1 MHz. When the kHz laser was used with pulse energies below 1 {mu}J, the predominant fluorescence was centered at 550 nm, a band assigned to the presence of silicon clusters (E{prime}{sub {delta}}). We also observed an increase in the intensity of the 605 cm{sup -1} Raman peak relative to the total Raman intensity, corresponding to an increase in the concentration of 3-membered rings in the lines fabricated with both laser systems.

  13. An Improved Method of Mitigating Laser Induced Surface Damage Growth in Fused Silica Using a Rastered, Pulsed CO2 Laser

    Energy Technology Data Exchange (ETDEWEB)

    Bass, I L; Guss, G M; Nostrand, M J; Wegner, P L

    2010-10-21

    A new method of mitigating (arresting) the growth of large (>200 m diameter and depth) laser induced surface damage on fused silica has been developed that successfully addresses several issues encountered with our previously-reported large site mitigation technique. As in the previous work, a tightly-focused 10.6 {micro}m CO{sub 2} laser spot is scanned over the damage site by galvanometer steering mirrors. In contrast to the previous work, the laser is pulsed instead of CW, with the pulse length and repetition frequency chosen to allow substantial cooling between pulses. This cooling has the important effect of reducing the heat-affected zone capable of supporting thermo-capillary flow from scale lengths on the order of the overall scan pattern to scale lengths on the order of the focused laser spot, thus preventing the formation of a raised rim around the final mitigation site and its consequent down-stream intensification. Other advantages of the new method include lower residual stresses, and improved damage threshold associated with reduced amounts of redeposited material. The raster patterns can be designed to produce specific shapes of the mitigation pit including cones and pyramids. Details of the new technique and its comparison with the previous technique will be presented.

  14. Characterization of Optical and Electrical Properties of Transparent Conductive Boron-Doped Diamond thin Films Grown on Fused Silica

    Directory of Open Access Journals (Sweden)

    Bogdanowicz Robert

    2014-12-01

    Full Text Available Abstract A conductive boron-doped diamond (BDD grown on a fused silica/quartz has been investigated. Diamond thin films were deposited by the microwave plasma enhanced chemical vapor deposition (MW PECVD. The main parameters of the BDD synthesis, i.e. the methane admixture and the substrate temperature were investigated in detail. Preliminary studies of optical properties were performed to qualify an optimal CVD synthesis and film parameters for optical sensing applications. The SEM micro-images showed the homogenous, continuous and polycrystalline surface morphology; the mean grain size was within the range of 100-250 nm. The fabricated conductive boron-doped diamond thin films displayed the resistivity below 500 mOhm cm-1 and the transmittance over 50% in the VIS-NIR wavelength range. The studies of optical constants were performed using the spectroscopic ellipsometry for the wavelength range between 260 and 820 nm. A detailed error analysis of the ellipsometric system and optical modelling estimation has been provided. The refractive index values at the 550 nm wavelength were high and varied between 2.24 and 2.35 depending on the percentage content of methane and the temperature of deposition.

  15. Comparison of neutron and gamma irradiation effects on KU1 fused silica monitored by electron paramagnetic resonance

    Energy Technology Data Exchange (ETDEWEB)

    Bravo, D. [Department Fisica de Materiales, Universidad Autonoma de Madrid, E-28049 Madrid (Spain)], E-mail: david.bravo@uam.es; Lagomacini, J.C. [Department Fisica de Materiales, Universidad Autonoma de Madrid, E-28049 Madrid (Spain); Leon, M.; Martin, P. [Materiales para Fusion, CIEMAT, Avda. Complutense 22, E-28040 Madrid (Spain); Martin, A. [Department Fisica e Instalaciones, ETS Arquitectura UPM, E-28040 Madrid (Spain); Lopez, F.J. [Department Fisica de Materiales, Universidad Autonoma de Madrid, E-28049 Madrid (Spain); Ibarra, A. [Materiales para Fusion, CIEMAT, Avda. Complutense 22, E-28040 Madrid (Spain)

    2009-06-15

    Electron paramagnetic resonance (EPR) studies have been carried out on KU1 fused silica irradiated with neutrons at fluences 10{sup 21} and 10{sup 22} n/m{sup 2}, and gamma-ray doses up to 12 MGy. The effects of post-irradiation thermal annealing treatments, up to 850 deg. C, have also been investigated. Paramagnetic oxygen-related defects (POR and NBOHC) and E'-type defects have been identified and their concentration has been measured as a function of neutron fluence, gamma dose and post-irradiation annealing temperature. It is found that neutrons at the highest fluence generate a much higher concentration of defects (mainly E' and POR, both at concentrations about 5 x 10{sup 18} spins/cm{sup 3}) than gamma irradiations at the highest dose (mainly E' at a concentration about 4 x 10{sup 17} spins/cm{sup 3}). Moreover, for gamma-irradiated samples a lower treatment temperature (about 400 deg. C) is required to annihilate most of the observed defects than for neutron-irradiated ones (about 600 deg. C)

  16. Correlating optical damage threshold with intrinsic defect populations in fused silica as a function of heat treatment temperature

    Energy Technology Data Exchange (ETDEWEB)

    Shen, N. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Matthews, M. J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Elhadj, S. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Miller, P. E. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Nelson, A. J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Hamilton, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2013-04-03

    Here, chemical vapor deposition (CVD) is used for the production of fused silica optics in high-power laser applications. However, relatively little is known about the ultraviolet laser damage threshold of CVD films and how they relate to intrinsic defects produced during deposition. We present here a study relating structural and electronic defects in CVD films to 355 nm pulsed-laser damage threshold as a function of post-deposition annealing temperature (THT). Plasma-enhanced CVD based on SiH4/N2O under oxygen-rich conditions was used to deposit 1.5, 3.1 and 6.4 µm thick films on etched SiO2 substrates. Rapid annealing was performed using a scanned CO2 laser beam up to THT ~ 2100 K. The films were then characterized using x-ray photoemission spectroscopy, Fourier transform infrared spectroscopy (FTIR) and photoluminescence spectroscopy. A gradual transition in the damage threshold of annealed films was observed for THT values up to 1600 K, correlating with a decrease in non-bridging silanol and oxygen deficient centres. An additional sharp transition in damage threshold also occurs at ~1850 K indicating substrate annealing. Based on our results, a mechanism for damage-related defect annealing is proposed, and the potential of using high-THT CVD SiO2 to mitigate optical damage is also discussed.

  17. P2. A fused silica Cherenkov detector for the high precision determination of the weak mixing angle

    Energy Technology Data Exchange (ETDEWEB)

    Gerz, Kathrin; Becker, Dominik; Jennewein, Thomas; Baunack, Sebastian [Johannes Gutenberg Universitaet Mainz (Germany); Kumar, Krishna [Department of Physics and Astronomy, Stony Brook University, Stony Brook (United States); Maas, Frank [Johannes Gutenberg Universitaet Mainz (Germany); Helmholtz Institut Mainz (Germany)

    2016-07-01

    The weak mixing angle is a central parameter of the standard model and its high precision determination is tantamount to probing for new physics effects. The P2 experiment at the MESA accelerator in Mainz will perform such a measurement of the weak mixing angle via parity violating electron-proton scattering. We aim to determine sin{sup 2}(Θ{sub W}) to a relative precision of 0.13%. Since the weak charge of the proton is small compared to its electric charge, the measurable asymmetry is only 33 ppb, requiring a challenging measurement to a precision of only 0.44 ppb. In order to achieve this precision we need to collect very high statistics and carefully minimize interfering effects like apparatus induced false asymmetries. We present the status of the development of an integrating fused-silica Cherenkov detector, which is suitable for a high precision and high intensity experiment like P2. The contribution will focus on the investigation of the detector's response to incoming signal and background particles both by simulations and by beam tests at the MAMI accelerator.

  18. Thermo-elasto-plastic simulations of femtosecond laser-induced structural modifications: Application to cavity formation in fused silica

    Science.gov (United States)

    Beuton, Romain; Chimier, Benoît; Breil, Jérôme; Hébert, David; Maire, Pierre-Henri; Duchateau, Guillaume

    2017-11-01

    The absorbed laser energy of a femtosecond laser pulse in a transparent material induces a warm dense matter region relaxation of which may lead to structural modifications in the surrounding cold matter. The modeling of the thermo-elasto-plastic material response is addressed to predict such modifications. It has been developed in a 2D plane geometry and implemented in a hydrodynamic Lagrangian code. The particular case of a tightly focused laser beam in the bulk of fused silica is considered as a first application of the proposed general model. It is shown that the warm dense matter relaxation, influenced by the elasto-plastic behavior of the surrounding cold matter, generates both strong shock and rarefaction waves. Permanent deformations appear in the surrounding solid matter if the induced stress becomes larger than the yield strength. This interaction results in the formation of a sub-micrometric cavity surrounded by an overdense area. This approach also allows one to predict regions where cracks may form. The present modeling can be used to design nanostructures induced by short laser pulses.

  19. Fused silica capillaries with two segments of different internal diameters and inner surface roughnesses prepared by etching with supercritical water and used for volume coupling electrophoresis

    Czech Academy of Sciences Publication Activity Database

    Horká, Marie; Karásek, Pavel; Roth, Michal; Šlais, Karel

    2017-01-01

    Roč. 38, 9-10 (2017), s. 1260-1267 ISSN 0173-0835 R&D Projects: GA ČR(CZ) GA16-03749S; GA MZd(CZ) NV16-29916A Institutional support: RVO:68081715 Keywords : fused silica capillary * supercritical water * volume coupling electrophoresis Subject RIV: CB - Analytical Chemistry, Separation OBOR OECD: Analytical chemistry Impact factor: 2.744, year: 2016

  20. Use of anionic surfactants for selective polishing of silicon dioxide over silicon nitride films using colloidal silica-based slurries

    Science.gov (United States)

    Penta, Naresh K.; Amanapu, H. P.; Peethala, B. C.; Babu, S. V.

    2013-10-01

    Four different anionic surfactants, sodium dodecyl sulfate, dodecyl benzene sulfonic acid (DBSA), dodecyl phosphate and Sodium lauroyl sarcosine, selected from the sulfate, phosphate, and carboxylic family, were investigated as additives in silica dispersions for selective polishing of silicon dioxide over silicon nitride films. We found that all these anionic surfactants suppress the nitride removal rates (RR) for pH ≤4 while more or less maintaining the oxide RRs, resulting in high oxide-to-nitride RR selectivity. The RR data obtained as a function of pH were explained based on pH dependent distributions of surfactant species, change in the zeta potentials of oxide and nitride surfaces, and thermogravimetric data. It appears that the negatively charged surfactant species preferentially adsorb on the positively charged nitride surface below IEP through its electrostatic interactions and form a bilayer adsorption, resulting in the suppression of nitride RRs. In contrast to the surfactants, K2SO4 interacts only weakly with the nitride surface and hence cannot suppress its RR.

  1. Silica sulfuric acid: a reusable solid catalyst for one pot synthesis of densely substituted pyrrole-fused isocoumarins under solvent-free conditions

    Directory of Open Access Journals (Sweden)

    Sudipta Pathak

    2013-11-01

    Full Text Available A convenient and efficient methodology for the synthesis of densely substituted pyrrole-fused isocoumarins, which employs solid-supported silica sulfuric acid (SSA as catalyst, has been developed. When the mixture of ninhydrin adducts of acetylacetone/ethyl acetoacetate and primary amines was heated on the solid surface of SSA under solvent-free conditions, the pyrrole-fused isocoumarins were formed in good yields. This synthetic method has several advantages such as the employment of solvent-free reaction conditions without the use of any toxic reagents and metal catalysts, the ease of product isolation, the use of a recyclable catalyst, the low cost, the easy availability of the starting materials, and the excellent yields of products.

  2. Determination of Hydrogen Diffusion Coefficients in Fused Silica From 23 to 250°C Using Raman Spectroscopy

    Science.gov (United States)

    Shang, L.; Chou, I.; Lu, W.; Burruss, R. C.

    2008-12-01

    The oxygen buffer technique is routinely used in experimental studies of redox sensitive geochemical reactions at elevated pressures (P) and temperatures (T). However, this technique is limited to T above about 400°C due to the low permeability of sample containers (Pt or Ag-Pd alloys) to hydrogen at lower T. Preliminary results of Chou et al. (Geochim. Cosmochim. Acta, 2008, doi:10.1016/j.gca.2008.07.030) indicate that the use of fused silica capillary (FSC) container may extend this technique to lower T. In this study, hydrogen diffusion coefficients (D) in FSC were determined from 23 to 250°C by measuring the loss of hydrogen from the FSC containers (0.3 mm OD, 0.1 mm ID, and ~10 mm long) with Raman spectroscopy using CO2 as an internal standard. First, CO2 was loaded cryogenically in a FSC capsule (Chou et al., ibid.). The capsule was then inserted in a protective ceramic tube, sealed in a gold capsule containing Fe powder and water, and heated at 300°C under 100 MPa of Ar external P in a cold-seal pressure vessel for several days allowing H2 to diffuse into the capsule. After quench, the Raman spectra were collected and the initial relative concentration of hydrogen in the silica capsule was derived from the peak height ratios between H2 (near 587 cm-1) and CO2 (near 1387 cm- 1). The sample capsule was then heated at a fixed T at one atmosphere to let H2 diffuse out of the capsule, and the changes of hydrogen concentration were monitored by Raman spectroscopy after quench. This process was repeated with different heating durations at 23 (room T), 50, 102, 157, 200, and 250°C. The values of D (in cm2s-1) in FSC were obtained by fitting the observed changes of hydrogen concentration to an equation based on Fick's second law. Our results can be represented by: Ln D (±0.14) = (-39810/RT) - 9.5491 (r2 = 0.9985) where R is the gas constant, and T in Kelvin. The slope corresponds to an activation energy of 39.81 kJ/mol. Our D values are about a half order of

  3. Analysis of optical properties behaviour of CLEARCERAM, fused silica and CaF2 glasses exposed to simulated space conditions

    Science.gov (United States)

    Fernández-Rodríguez, M.; Alvarado, C. G.; Núñez, A.; Álvarez-Herrero, A.

    2017-11-01

    produced by the radiation environment on the optical materials can be classified in two types: ionizing or non-ionizing. This damage may produce continual or accumulative (dose) alterations on the optical material performances, or may produce alterations which not remain along the time (transitory effects). The effects of the radiation on optical materials can be summarized on changes of optical transmission and refractive index, variation of density and superficial degradation [4-6]. Two non-invasive and non-destructive techniques such as Optical Spectrum Analyzer and Spectroscopic Ellipsometry [7] have been used to characterize optically the three kinds of studied glasses, CaF2, Fused Silica and Clearceram. The study of the temperature and radiation effects on the glasses optical properties showed that the gamma radiation is the principal responsible of glasses optical degradation. The optical properties of the Clearceram glass have been affected by the gamma irradiation due to the absorption bands induced by the radiation in the visible spectral range (color centers). Therefore, an analysis about the behavior of these color centers with the gamma radiation total dose and with the time after the irradiation has been carried out in the same way that it is performed in [8].

  4. Analysis of polycyclic aromatic hydrocarbons I. Determination by gas chromatography with glass and fused silica capillary columns; Analisis de Hidrocarburos aromaticos policiclicos. I. Determinacion por cromatografia de gases con columnas capilares de vidrio de silice fundida

    Energy Technology Data Exchange (ETDEWEB)

    Perez, M. M.; Gonzalez, D.

    1987-07-01

    A study of the analysis by gas chromatography of aromatic polycyclic hydrocarbons is presented. The separation has been carried out by glass and fused silica capillary column. The limitations and the advantages of the procedure are discussed in terms of separation efficiency, sensitivity and precision. (Author) 17 refs.

  5. Growth of carbon nanofiber coatings on nickel thin films on fused silica by catalytic thermal chemical vapor deposition: On the use of titanium, titanium-tungsten and tantalum as adhesion layers

    NARCIS (Netherlands)

    Thakur, D.B.; Tiggelaar, Roald M.; Gardeniers, Johannes G.E.; Lefferts, Leonardus; Seshan, Kulathuiyer

    2009-01-01

    Coatings of carbon nanofiber (CNF) layers were synthesized on fused silica substrates using a catalytic thermal chemical vapor deposition process (C-TCVD). The effects of various adhesion layers–titanium, titanium–tungsten and tantalum–under the nickel thin film on the attachment of carbon

  6. Influence of fused Silica and chills incorporation on Corrosion, Thermal and Chemical composition of ASTM A 494 M Grade Nickel alloy

    Science.gov (United States)

    Purushotham, G.; Hemanth, Joel

    2016-09-01

    A review of a host of relevant literature on the composites leads to some important observations on the gap that prevails for developing the composite with increased strength to weight ratio, improved thermal properties and reduced corrosion rate with the addition of fused SiO2 dispersoid for the nickel based alloy. In the arena of engineering, metallurgists look for techniques to improve the thermal, corrosion and chemical properties of the materials. In this connection an investigation has been carried out to fabricate and evaluate the corrosion, chemical and thermal properties of chilled composites consisting of nickel matrix with fused silica particles (size 40-150 μm) in the matrix. The main objective of the present research is to obtain fine grain Ni/SiO2 chilled sound composite having very good properties. The dispersoid added ranged from 3 to 12 wt. % in steps of 3%. The subsequent composites cast in molds containing metallic and non-metallic chill blocks (MS, SiC & Cu) were tested for their microstructure, chemical, thermal properties and corrosion behavior.

  7. [Amorphous silica. Types, health effects of exposure, NDS].

    Science.gov (United States)

    Woźniak, H; Wiecek, E

    1995-01-01

    Maximum allowable concentration (MAC) values for amorphous silica dust have not been identified in the Polish legal regulations up-to-date. In this work the authors review values of allowable (recommended) amorphous silica dust concentrations in other countries. Data on other types of amorphous silica (natural and synthetic) used in industry as well as data on health effects of exposure to these types of dust are presented. The work encompasses 42 entries in the references and one Table which includes the following proposed MAC values: Non-calcinate diatomaceous earth (diatomite) and synthetic silica: Total dust--10 mg/m3 Respirable dust--2 mg/m3 Calcinate diatomaceous earth (diatomite) and fused silica (vitreous silica): Total dust--2 mg/m3 Respirable dust--1 mg/m3.

  8. Optical Evaluation of Digital Micromirror Devices (DMDs) with UV-Grade Fused Silica, Sapphire, and Magnesium Fluoride Windows and Longterm Reflectance of Bare Devices

    Science.gov (United States)

    Quijada, Manuel A.; Travinsky, Anton; Vorobiev, Dmitry; Ninkov, Zoran; Raisanen, Alan; Robberto, Massimo; Heap, Sara

    2016-01-01

    Digital micromirror devices (DMDs) are commercial micro-electromechanical systems, consisting of millions of mirrors which can be individually addressed and tilted into one of two states (+/-12deg). These devices were developed to create binary patterns in video projectors, in the visible range. Commercially available DMDs are hermetically sealed and extremely reliable. Recently, DMDs have been identified as an alternative to microshutter arrays for space-based multi-object spectrometers (MOS). Specifically, the MOS at the heart of the proposed Galactic Evolution Spectroscopic Explorer (GESE) uses the DMD as a reprogrammable slit mask. Unfortunately, the protective borosilicate windows limit the use of DMDs in the UV and IR regimes, where the glass has insufficient throughput. In this work, we present our efforts to replace standard DMD windows with custom windows made from UV-grade fused silica, low-absorption optical sapphire (LAOS) and magnesium fluoride (MgF2). We present transmission measurements of the antireflection coated windows and the reflectance of bare (window removed) DMDs. Furthermore, we investigated the long-term stability of the DMD reflectance and experiments for coating DMD active area with a layer of pure aluminum (Al) to boost reflectance performance in the UV spectral range (200-400 nm).

  9. Chiral separation of methoxamine and lobeline in capillary zone electrophoresis using ethylbenzene-deactivated fused-silica capillary columns and cyclodextrins as buffer additives.

    Science.gov (United States)

    Russo, M V

    2002-08-01

    The complete chiral separation of methoxamine and lobeline was achieved by capillary zone electrophoresis on an ethylbenzene-deactivated fused-silica capillary column and with cyclodextrins (CDs) as buffer additives. Among the CDs investigated in this study, i.e. alpha-CD, beta-CD, dimethyl-beta-CD, hydroxypropyl-beta-CD and gamma-CD, all the three beta-type CDs showed chiral recognition on the two drugs investigated. Under the investigated conditions, the baseline chiral separation of methoxamine can be achieved with 90 mM Tris-H3PO4 (pH 2.5) containing 11.5 mM of the three beta-type CDs, with dimethyl-beta-CD giving the best resolution, whereas the baseline chiral separation of lobeline can be realized by using 90 mM Tris-H3PO4 buffer (pH 2.5) containing 5.8 mM dimethyl-beta-CD or 29.5 mM hydroxypropyl-beta-CD.

  10. Bi-stage time evolution of nano-morphology on inductively coupled plasma etched fused silica surface caused by surface morphological transformation

    Science.gov (United States)

    Jiang, Xiaolong; Zhang, Lijuan; Bai, Yang; Liu, Ying; Liu, Zhengkun; Qiu, Keqiang; Liao, Wei; Zhang, Chuanchao; Yang, Ke; Chen, Jing; Jiang, Yilan; Yuan, Xiaodong

    2017-07-01

    In this work, we experimentally investigate the surface nano-roughness during the inductively coupled plasma etching of fused silica, and discover a novel bi-stage time evolution of surface nano-morphology. At the beginning, the rms roughness, correlation length and nano-mound dimensions increase linearly and rapidly with etching time. At the second stage, the roughening process slows down dramatically. The switch of evolution stage synchronizes with the morphological change from dual-scale roughness comprising long wavelength underlying surface and superimposed nano-mounds to one scale of nano-mounds. A theoretical model based on surface morphological change is proposed. The key idea is that at the beginning, etched surface is dual-scale, and both larger deposition rate of etch inhibitors and better plasma etching resistance at the surface peaks than surface valleys contribute to the roughness development. After surface morphology transforming into one-scale, the difference of plasma resistance between surface peaks and valleys vanishes, thus the roughening process slows down.

  11. Pre-concentration and separation of bacteria by volume coupling electrophoresis on supercritical water-etched fused silica capillary with two segments of different internal diameters and inner surface roughnesses

    Czech Academy of Sciences Publication Activity Database

    Horká, Marie; Karásek, Pavel; Roth, Michal; Růžička, F.

    2018-01-01

    Roč. 410, č. 1 (2018), s. 167-175 ISSN 1618-2642 R&D Projects: GA MV(CZ) VI20172020069; GA ČR(CZ) GA16-03749S; GA MZd(CZ) NV16-29916A Keywords : fused silica capillary * volume coupling electrophoresis * supercritical water * blood Subject RIV: CB - Analytical Chemistry , Separation OBOR OECD: Analytical chemistry Impact factor: 3.431, year: 2016

  12. Pre-concentration and separation of bacteria by volume coupling electrophoresis on supercritical water-etched fused silica capillary with two segments of different internal diameters and inner surface roughnesses

    Czech Academy of Sciences Publication Activity Database

    Horká, Marie; Karásek, Pavel; Roth, Michal; Růžička, F.

    2018-01-01

    Roč. 410, č. 1 (2018), s. 167-175 ISSN 1618-2642 R&D Projects: GA MV(CZ) VI20172020069; GA ČR(CZ) GA16-03749S; GA MZd(CZ) NV16-29916A Keywords : fused silica capillary * volume coupling electrophoresis * supercritical water * blood Subject RIV: CB - Analytical Chemistry, Separation OBOR OECD: Analytical chemistry Impact factor: 3.431, year: 2016

  13. Raman spectroscopic measurements of CO2 density: Experimental calibration with high-pressure optical cell (HPOC) and fused silica capillary capsule (FSCC) with application to fluid inclusion observations

    Science.gov (United States)

    Wang, X.; Chou, I-Ming; Hu, W.; Burruss, Robert; Sun, Q.; Song, Y.

    2011-01-01

    Raman spectroscopy is a powerful method for the determination of CO2 densities in fluid inclusions, especially for those with small size and/or low fluid density. The relationship between CO2 Fermi diad split (Δ, cm−1) and CO2 density (ρ, g/cm3) has been documented by several previous studies. However, significant discrepancies exist among these studies mainly because of inconsistent calibration procedures and lack of measurements for CO2fluids having densities between 0.21 and 0.75 g/cm3, where liquid and vapor phases coexist near room temperature.In this study, a high-pressure optical cell and fused silica capillary capsules were used to prepare pure CO2 samples with densities between 0.0472 and 1.0060 g/cm3. The measured CO2 Fermi diad splits were calibrated with two well established Raman bands of benzonitrile at 1192.6 and 1598.9 cm−1. The relationship between the CO2 Fermi diad split and density can be represented by: ρ = 47513.64243 − 1374.824414 × Δ + 13.25586152 × Δ2 − 0.04258891551 × Δ3(r2 = 0.99835, σ = 0.0253 g/cm3), and this relationship was tested by synthetic fluid inclusions and natural CO2-rich fluid inclusions. The effects of temperature and the presence of H2O and CH4 on this relationship were also examined.

  14. Pulsed-laser machining and polishing of silica micro-optical components using a CO2 laser and an acousto-optic modulator

    Science.gov (United States)

    Nowak, Krzysztof M.; Baker, Howard J.; Hall, Denis R.

    2003-04-01

    Laser ablation and laser smoothing of silica is investigated as a method of manufacturing custom micro-optics for use with high-power, diode laser arrays. A highly flexible machining regime has been identified that uses 30 to 60 microseconds square pulses, generated from a stabilized CO2 laser by an acousto-optical modulator (AOM). Refractive optical surfaces with apertures of 1 mm x 1 mm have been generated by the multi-pulse, raster scanning method with cut depths in the range of 10 to 30 μm controlled to an accuracy of better than 150 nm. A subsequent laser "fire polishing" step to smooth out the surface, using the same laser system as for machining, but in a long pulse mode at an energy fluence that just avoids further ablation of the surface. The objective of the research is to produce rapid prototyping of arrays of refractive elements, to avoid the tooling or mask-writing steps of alternative methods. A particular interest is in the generation of corrective optical elements to improve the beam quality of arrays of diode laser bars.

  15. Evaluation of fused-core and monolithic versus porous silica-based C18 columns and porous graphitic carbon for ion-pairing liquid chromatography analysis of catecholamines and related compounds.

    Science.gov (United States)

    Chirita, Raluca-Ioana; Finaru, Adriana-Luminita; Elfakir, Claire

    2011-03-15

    This paper evaluates the performances of reversed-phase (RPLC) and ion-pairing chromatography (IPLC) coupled with UV detection for the analysis of a set of 12 catecholamines and related compounds. Different chromatographic columns (porous C18-silica, perfluorinated C18-silica, porous graphitic carbon, monolithic and fused-core silica-based C18 columns) were tested using semi-long perfluorinated carboxylic acids as volatile ion-pairing reagents. Much more promising results were obtained by IPLC than by RPLC and important improvements in analytes peak symmetry and separation resolution were observed when using the "fast chromatography" columns (monolithic and fused-core C18) under IPLC conditions. For UV detection, a satisfactory separation of the 12 selected analytes was achieved in less than 20 min by using a fused-core particles column (Halo C18) and a mobile phase composed of a 1.25 mM nonafluoropentanoic acid aqueous solution and methanol under gradient elution mode. The chromatographic method developed can be directly coupled with electrospray ionization tandem mass spectrometry (ESI-MS/MS) in positive ionization mode and 10 solutes among those selected can be observed. The presence of the acidic ion-pairing reagent in the mobile phase makes this system incompatible with negative ionization mode and thus unable to detect the two acidic compounds that only responded in negative mode. In terms of MS detection, Monolithic C18 column proved to be the best one to reach the lowest detection limits (LODs) (from 0.5 ngmL(-1) to 10 ngmL(-1) depending on the neurotransmitter). The applicability of the optimized LC-MS/MS method to a "real world" sample was finally evaluated. The presence of the matrix leads to signal suppression for several solutes and thus to higher LODs. Copyright © 2011 Elsevier B.V. All rights reserved.

  16. Evidence of a green luminescence band related to surface flaws in high purity silica glass

    Energy Technology Data Exchange (ETDEWEB)

    Fournier, J.; Neauport, J.; Grua, P. [CEA, CESTA, F-33114 Le Barp (France); Fournier, J.; Fargin, E.; Jubera, V. [Univ Bordeaux, CNRS, ICMCB, F-33608 Pessac (France); Talaga, D. [Univ Bordeaux, CNRS, ISM, F-33405 Talence (France); Jouannigot, S. [Univ Bordeaux 1, LCTS, SAFRAN, CNRS, CEA, UMR 5801, Pessac (France)

    2010-07-01

    Using luminescence con-focal microscopy under 325 nm laser excitation, we explore the populations of defects existing in or at the vicinity of macroscopic surface flaws in fused silica. We report our luminescence results on two types of surface flaws: laser damage and indentation on fused silica polished surfaces. Luminescence cartographies are made to show the spatial distribution of each kind of defect. Three bands, centered at 1.89 eV, 2.75 eV and 2.25 eV are evidenced on laser damage and indentations. The band centered at 2.25 eV was not previously reported in photo luminescence experiments on indentations and pristine silica, for excitation wavelengths of 325 nm or larger. The luminescent objects, expected to be trapped in sub-surface micro-cracks, are possibly involved in the first step of the laser damage mechanism when fused silica is enlightened at 351 nm laser in nanosecond regime. (authors)

  17. Implantation of plasmonic nanoparticles in SiO{sub 2} by pulsed laser irradiation of gold films on SiO{sub x}-coated fused silica and subsequent thermal annealing

    Energy Technology Data Exchange (ETDEWEB)

    Stolzenburg, H. [Laser-Laboratorium Göttingen, Hans-Adolf-Krebs-Weg 1, 37077 Göttingen (Germany); Peretzki, P.; Wang, N.; Seibt, M. [IV. Physikalisches Institut, Universität Göttingen, Friedrich-Hund-Platz 1, 37077 Göttingen (Germany); Ihlemann, J., E-mail: juergen.ihlemann@llg-ev.de [Laser-Laboratorium Göttingen, Hans-Adolf-Krebs-Weg 1, 37077 Göttingen (Germany)

    2016-06-30

    Highlights: • Gold nanoparticles are implanted in glass by pulsed UV-laser irradiation. • Implantation of gold into SiO{sub x} and annealing leads to Au-particles in quartz glass. • TEM investigations reveal particles with 10–60 nm diameter in a depth of 40 nm. • Implanted particles show plasmon resonance at 540 nm. - Abstract: The pulsed UV-laser irradiation of thin noble metal films deposited on glass substrates leads to the incorporation of metal particles in the glass, if a sufficiently high laser fluence is applied. This process is called laser implantation. For the implantation of gold into pure fused silica, high laser fluences (∼1 J/cm{sup 2} at 193 nm laser wavelength) are required. Using a SiO{sub x} (x ≈ 1) coated SiO{sub 2}-substrate, the implantation of gold into this coating can be accomplished at significantly lower fluences starting from 0.2 J/cm{sup 2} (comparable to those used for standard glass). Particles with diameters in the range of 10–60 nm are implanted to a depth of about 40 nm as identified by transmission electron microscopy. An additional high temperature annealing step in air leads to the oxidation of SiO{sub x} to SiO{sub 2}, without influencing the depth distribution of particles significantly. Only superficial, weakly bound particles are released and can be wiped away. Absorption spectra show a characteristic plasmon resonance peak at 540 nm. Thus, pure silica glass (SiO{sub 2}) with near surface incorporated plasmonic particles can be fabricated with this method. Such material systems may be useful for example as robust substrates for surface enhanced Raman spectroscopy (SERS).

  18. Impact of storage induced outgassing organic contamination on laser induced damage of silica optics at 351 nm.

    Science.gov (United States)

    Bien-Aimé, K; Belin, C; Gallais, L; Grua, P; Fargin, E; Néauport, J; Tovena-Pecault, I

    2009-10-12

    The impact of storage conditions on laser induced damage density at 351 nm on bare fused polished silica samples has been studied. Intentionally outgassing of polypropylene pieces on silica samples was done. We evidenced an important increase of laser induced damage density on contaminated samples demonstrating that storage could limit optics lifetime performances. Atomic Force Microscopy (AFM) and Gas Chromatography -Mass Spectrometry (GC-MS) have been used to identify the potential causes of this effect. It shows that a small quantity of organic contamination deposited on silica surface is responsible for this degradation. Various hypotheses are proposed to explain the damage mechanism. The more likely hypothesis is a coupling between surface defects of optics and organic contaminants.

  19. Polish visit

    CERN Document Server

    2003-01-01

    On 6 October, Professor Michal Kleiber, Polish Minister of Science and Chairman of the State Committee for Scientific Research, visited CERN and met both the current and designated Director General, Luciano Maiani and Robert Aymar. Professor Kleiber visited the CMS and ATLAS detector assembly halls, the underground cavern for ATLAS, and the LHC superconducting magnet string test hall. Michal Kleiber (left), Polish minister of science and Jan Krolikowski, scientist at Warsaw University and working for CMS, who shows the prototypes of the Muon Trigger board of CMS.

  20. High-voltage safety fuses for the transition-radiation tracking detector in the ATLAS experiment

    NARCIS (Netherlands)

    Voronov, SA; Voronov, YA; Onishchenko, EM; Simakov, AB; Sosnovtsev, VV; Suchkov, SI; Sugrobova, TA

    2004-01-01

    A safety fuse has been designed for the electrical protection of gas-filled detectors in the ATLAS experiment at CERN (Geneva, Switzerland). The fuse is a polished lithium niobate plate with a titanium strip of 91-kOmega resistance deposited by the photolithographic technique. The forced blow-out

  1. Laser-driven formation of a high-pressure phase in amorphous silica.

    Science.gov (United States)

    Salleo, Alberto; Taylor, Seth T; Martin, Michael C; Panero, Wendy R; Jeanloz, Raymond; Sands, Timothy; Génin, François Y

    2003-12-01

    Because of its simple composition, vast availability in pure form and ease of processing, vitreous silica is often used as a model to study the physics of amorphous solids. Research in amorphous silica is also motivated by its ubiquity in modern technology, a prominent example being as bulk material in transmissive and diffractive optics for high-power laser applications such as inertial confinement fusion (ICF). In these applications, stability under high-fluence laser irradiation is a key requirement, with optical breakdown occurring when the fluence of the beam is higher than the laser-induced damage threshold (LIDT) of the material. The optical strength of polished fused silica transmissive optics is limited by their surface LIDT. Surface optical breakdown is accompanied by densification, formation of point defects, cratering, material ejection, melting and cracking. Through a combination of electron diffraction and infrared reflectance measurements we show here that synthetic vitreous silica transforms partially into a defective form of the high-pressure stishovite phase under high-intensity (GW cm(-2)) laser irradiation. This phase transformation offers one suitable mechanism by which laser-induced damage grows catastrophically once initiated, thereby dramatically shortening the service lifetime of optics used for high-power photonics.

  2. Impact of environmental contamination on laser induced damage of silica optics in Laser MegaJoule

    International Nuclear Information System (INIS)

    Bien-Aime, K.

    2009-11-01

    Laser induced damage impact of molecular contamination on fused polished silica samples in a context of high power laser fusion facility, such as Laser MegaJoule (LMJ) has been studied. One of the possible causes of laser induced degradation of optical component is the adsorption of molecular or particular contamination on optical surfaces. In the peculiar case of LMJ, laser irradiation conditions are a fluence of 10 J/cm 2 , a wavelength of 351 nm, a pulse duration of 3 ns for a single shot/days frequency. Critical compounds have been identified thanks to environmental measurements, analysis of material outgassing, and identification of surface contamination in the critical environments. Experiments of controlled contamination involving these compounds have been conducted in order to understand and model mechanisms of laser damage. Various hypotheses are proposed to explain the damage mechanism. (author)

  3. Metal polish poisoning

    Science.gov (United States)

    Metal polishes are used to clean metals, including brass, copper, or silver. This article discusses the harmful effects from swallowing metal polish. This article is for information only. DO NOT use ...

  4. Williamson Polishing & Plating Site

    Science.gov (United States)

    Williamson Polishing & Plating Co. Inc. was a plating shop located in the Martindale-Brightwood neighborhood of Indianapolis. The facility conducted job shop polishing and electroplating services. The vacant site contains a 14,651-square-foot building.

  5. An experimental and analytical investigation into the effects of process vibrations on material removal rates during polishing

    Science.gov (United States)

    Mullany, B.; Mainuddin, M.; Williams, W.; Keanini, R.

    2013-06-01

    Experimental testing, using both commercially available polishing machines and a specially built test platform, demonstrates that material removal rates (MRRs) observed during polishing of fused silica are strongly affected by nanometer-scale vibration amplitudes. Specifically, a nanometer level increase in system vibrations can produce MRRs approximately 150% higher than on an inherently smoother running machine. Moreover the higher spatial frequency surface roughness values are little-effected by the spectral content of the polishing machine. Polishing under controlled conditions, using the test platform, shows that for vibration amplitudes, A ≲ 1.6 μm, and over a fairly wide range of vibration frequencies, MRR increases almost linearly with increasing input power. By contrast, for A ≳ 10 μm, MRR exhibits a rapid decay with increasing A. Order of magnitude analyses and physical arguments are presented in order to explain the qualitatively distinct MRR trends observed. In the small-amplitude limit, A ≲ 1.6 μm, two arguments are presented which suggest that the total observed removal rate, MRRtot, reflects the superposed action of chemical-mechanical removal, MRRcm, and vibration-driven, flow-induced removal, MRRflow, i.e., MRRtot=MRRcm+MRRflow. The analyses further indicate that MRRflow primarily reflects cyclic viscous shears and pressure gradients extant within the thin, non-Newtonian slurry film that exists between the polishing tool and workpiece. Shears and pressure gradients, and corresponding flow-induced MRRs, are, in turn, found to scale as √A /do ω, where A is the vibration amplitude, do is the characteristic gap thickness between the tool and workpiece, and ω is the vibration frequency. In the large-amplitude limit, A ≳ 5 μm, experimental measurements and a simple scaling argument show that the polishing slurry film becomes thick enough that the workpiece and polishing tool lose direct contact. In this limit, observed MRRs thus reflect

  6. Functional Use Database (FUse)

    Data.gov (United States)

    U.S. Environmental Protection Agency — There are five different files for this dataset: 1. A dataset listing the reported functional uses of chemicals (FUse) 2. All 729 ToxPrint descriptors obtained from...

  7. Development of highly polished, grazing incidence mirrors for synchrotron radiation beam lines at SSRL

    International Nuclear Information System (INIS)

    Tirsell, K.G.; Berglin, E.J.; Fuchs, B.A.; Holdener, F.R.; Humpal, H.H.; Karpenko, V.P.; Kulkarni, S.; Fantone, S.D.

    1987-08-01

    New platinum-coated grazing incidence mirrors with low surface roughnesses have been developed to focus bending magnet radiation from the SSRL/SLAC SPEAR storage ring on the entrance slits of two Beam Line VIII grating monochromators. The first mirror in the toroidal grating monochromator (TGM) branch is a cooled SiC cylinder capable of absorbing synchrotron radiation power levels of up to 260 watts without excessive distortion. This mirror deflects the beam vertically through a 12/degree/ angle and focuses it sagitally on the TGM entrance slit plane. The second TGM optical element is a fused-silica spherical mirror with a large radius of curvature that deflects the beam vertically through an additional 12/degree/ and focuses it tangentially with 3/1 demagnification. The first mirror in our spherical grating branch is a 5/degree/-vertically deflecting, cooled SiC toroid designed to focus tangentially on the monochromator entrance slits and sagitally in the exit slits. A 4/degree/-deflecting fused silica mirror is used after the exit sites in each beam line to refocus on to the sample. For this application a thin cylinder is bent to approximate an ellipsoid. The mirrors are now installed at SSRL and performance measurements are planned. Qualitatively the focus of the TGM optics at the entrance slit plane appears very good. In this paper we discuss considerations leading to the choice of SiC for each of the two first mirrors. We present highlights of the development of these mirrors with some emphasis on SiC polishing techniques. In addition, the specialized metrology developed to produce the more difficult figure of the toroid will be described. Measured surface roughness and figure results will be presented. 19 refs., 11 figs

  8. Development of highly polished, grazing incidence mirrors for synchrotron radiation beam lines at SSRL

    Energy Technology Data Exchange (ETDEWEB)

    Tirsell, K.G.; Berglin, E.J.; Fuchs, B.A.; Holdener, F.R.; Humpal, H.H.; Karpenko, V.P.; Kulkarni, S.; Fantone, S.D.

    1987-08-01

    New platinum-coated grazing incidence mirrors with low surface roughnesses have been developed to focus bending magnet radiation from the SSRL/SLAC SPEAR storage ring on the entrance slits of two Beam Line VIII grating monochromators. The first mirror in the toroidal grating monochromator (TGM) branch is a cooled SiC cylinder capable of absorbing synchrotron radiation power levels of up to 260 watts without excessive distortion. This mirror deflects the beam vertically through a 12/degree/ angle and focuses it sagitally on the TGM entrance slit plane. The second TGM optical element is a fused-silica spherical mirror with a large radius of curvature that deflects the beam vertically through an additional 12/degree/ and focuses it tangentially with 3/1 demagnification. The first mirror in our spherical grating branch is a 5/degree/-vertically deflecting, cooled SiC toroid designed to focus tangentially on the monochromator entrance slits and sagitally in the exit slits. A 4/degree/-deflecting fused silica mirror is used after the exit sites in each beam line to refocus on to the sample. For this application a thin cylinder is bent to approximate an ellipsoid. The mirrors are now installed at SSRL and performance measurements are planned. Qualitatively the focus of the TGM optics at the entrance slit plane appears very good. In this paper we discuss considerations leading to the choice of SiC for each of the two first mirrors. We present highlights of the development of these mirrors with some emphasis on SiC polishing techniques. In addition, the specialized metrology developed to produce the more difficult figure of the toroid will be described. Measured surface roughness and figure results will be presented. 19 refs., 11 figs.

  9. High-voltage safety fuses for the transition-radiation tracking detector in the ATLAS experiment

    CERN Document Server

    Voronov, S A; Onishchenko, E M; Simakov, A B; Sosnovtsev, V V; Suchkov, S; Sugrobova, T A

    2004-01-01

    A safety fuse has been designed for the electrical protection of gas- filled detectors in the ATLAS experiment at CERN (Geneva, Switzerland). The fuse is a polished lithium niobate plate with a titanium strip of 91-kOmega resistance deposited by the photolithographic technique. The forced blowout time of the fuse is 10-50 ms; whereupon the leakage current through it is less than 1 nA at a 2-kV voltage. The resistance of the fuse case is greater than or equivalent equal' greater than 10**1**2 Omega. Its overall dimensions are 5.8 multiplied by 3.8 multiplied by 2 mm.

  10. Novel synthesis of a series of spiro 1,3-indanedione-fused dihydropyridines through the condensation of a tetrone with N-aryl/alkylenamines in presence of solid support silica sulfuric acid.

    Science.gov (United States)

    Kundu, Ashis; Pramanik, Animesh

    2015-08-01

    A convenient protocol for the library synthesis of biologically important 1-aryl-2',6-spiro(1',3'-indanedione)-1H-indeno[1,2-b]quinoline-5,7-diones has been developed. In this one-pot reaction protocol a tetrone is condensed with various N-aryl/alkylenamines of 1,3-cyclohexadiones on the surface of a solid-supported acid catalyst silica sulfuric acid under solvent-free condition. The significant advantages of this methodology are the use of solvent-free reaction conditions, operational simplicity of the reaction, good yield of the products with high atom economy, and employment of a recyclable catalyst. All these favorable factors make the present method convenient, economic, and 'benign by design'.

  11. Polish Cartographical Review

    Directory of Open Access Journals (Sweden)

    Nedjeljko Frančula

    2017-07-01

    Full Text Available The Polish Cartographical Review (PCR journal has been published in English four times a year since 2015. The journal is in open access and it is published by De Gruyter Open. It is edited by Polish scientists in collaboration with international experts.

  12. OLED panel with fuses

    Science.gov (United States)

    Levermore, Levermore; Pang, Huiqing; Rajan, Kamala

    2014-09-16

    Embodiments may provide a first device that may comprise a substrate, a plurality of conductive bus lines disposed over the substrate, and a plurality of OLED circuit elements disposed on the substrate, where each of the OLED circuit elements comprises one and only one pixel electrically connected in series with a fuse. Each pixel may further comprise a first electrode, a second electrode, and an organic electroluminescent (EL) material disposed between the first and the second electrodes. The fuse of each of the plurality of OLED circuit elements may electrically connect each of the OLED circuit elements to at least one of the plurality of bus lines. Each of the plurality of bus lines may be electrically connected to a plurality of OLED circuit elements that are commonly addressable and at least two of the bus lines may be separately addressable.

  13. Silica Nephropathy

    Directory of Open Access Journals (Sweden)

    N Ghahramani

    2010-06-01

    Full Text Available Occupational exposure to heavy metals, organic solvents and silica is associated with a variety of renal manifestations. Improved understanding of occupational renal disease provides insight into environmental renal disease, improving knowledge of disease pathogenesis. Silica (SiO2 is an abundant mineral found in sand, rock, and soil. Workers exposed to silica include sandblasters, miners, quarry workers, masons, ceramic workers and glass manufacturers. New cases of silicosis per year have been estimated in the US to be 3600–7300. Exposure to silica has been associated with tubulointerstitial disease, immune-mediated multisystem disease, chronic kidney disease and end-stage renal disease. A rare syndrome of painful, nodular skin lesions has been described in dialysis patients with excessive levels of silicon. Balkan endemic nephropathy is postulated to be due to chronic intoxication with drinking water polluted by silicates released during soil erosion. The mechanism of silica nephrotoxicity is thought to be through direct nephrotoxicity, as well as silica-induced autoimmune diseases such as scleroderma and systemic lupus erythematosus. The renal histopathology varies from focal to crescentic and necrotizing glomerulonephritis with aneurysm formation suggestive of polyarteritis nodosa. The treatment for silica nephrotoxicity is non-specific and depends on the mechanism and stage of the disease. It is quite clear that further research is needed, particularly to elucidate the pathogenesis of silica nephropathy. Considering the importance of diagnosing exposure-related renal disease at early stages, it is imperative to obtain a thorough occupational history in all patients with renal disease, with particular emphasis on exposure to silica, heavy metals, and solvents.

  14. Fused Lasso Additive Model.

    Science.gov (United States)

    Petersen, Ashley; Witten, Daniela; Simon, Noah

    2016-01-01

    We consider the problem of predicting an outcome variable using p covariates that are measured on n independent observations, in a setting in which additive, flexible, and interpretable fits are desired. We propose the fused lasso additive model (FLAM), in which each additive function is estimated to be piecewise constant with a small number of adaptively-chosen knots. FLAM is the solution to a convex optimization problem, for which a simple algorithm with guaranteed convergence to a global optimum is provided. FLAM is shown to be consistent in high dimensions, and an unbiased estimator of its degrees of freedom is proposed. We evaluate the performance of FLAM in a simulation study and on two data sets. Supplemental materials are available online, and the R package flam is available on CRAN.

  15. Applicability of chemical vapour polishing of additive manufactured parts to meet production-quality

    DEFF Research Database (Denmark)

    Pedersen, D. B.; Hansen, H. N.; Nielsen, J. S.

    2014-01-01

    The Fused Deposition Modelling (FDM) method is the most rapidly growing Additive Manufacturing (AM) method[1]. FDM employs a 2.5D deposition scheme which induce a step-ladder shaped surface definition [2], with seams of the individual layers clearly visible[3]. This paper investigate to which...... extend chemical vapour polishing can be applied to eliminate the layered surfaces from FDM, so that a polished surface quality is obtained. It is quantified to what extend parts can be vapour polished and how geometrical and mechanical properties alter. The fundamental question is whether the surfaces...... of FDM manufactured parts can be taken from their current quality into the precision engineering domain....

  16. Functional Median Polish

    KAUST Repository

    Sun, Ying

    2012-08-03

    This article proposes functional median polish, an extension of univariate median polish, for one-way and two-way functional analysis of variance (ANOVA). The functional median polish estimates the functional grand effect and functional main factor effects based on functional medians in an additive functional ANOVA model assuming no interaction among factors. A functional rank test is used to assess whether the functional main factor effects are significant. The robustness of the functional median polish is demonstrated by comparing its performance with the traditional functional ANOVA fitted by means under different outlier models in simulation studies. The functional median polish is illustrated on various applications in climate science, including one-way and two-way ANOVA when functional data are either curves or images. Specifically, Canadian temperature data, U. S. precipitation observations and outputs of global and regional climate models are considered, which can facilitate the research on the close link between local climate and the occurrence or severity of some diseases and other threats to human health. © 2012 International Biometric Society.

  17. Raman Investigation of the Effects on Fused Silica Fibers

    Science.gov (United States)

    1983-01-12

    Cottle Road Department of Chemistry San Jose., California 95143 Wayne State University Detroit, Michigan 49207 1 Dr. Carmen Ortiz Cousejo Superior de Investigaciones Cientificas Serrano 117 Madrid 6, Spain - #

  18. Comparing monolithic and fused core HPLC columns for fast chromatographic analysis of fat-soluble vitamins.

    Science.gov (United States)

    Kurdi, Said El; Muaileq, Dina Abu; Alhazmi, Hassan A; Bratty, Mohammed Al; Deeb, Sami El

    2017-06-27

    HPLC stationary phases of monolithic and fused core type can be used to achieve fast chromatographic separation as an alternative to UPLC. In this study, monolithic and fused core stationary phases are compared for fast separation of four fat-soluble vitamins. Three new methods on the first and second generation monolithic silica RP-18e columns and a fused core pentafluoro-phenyl propyl column were developed. Application of three fused core columns offered comparable separations of retinyl palmitate, DL-α-tocopheryl acetate, cholecalciferol and menadione in terms of elution speed and separation efficiency. Separation was achieved in approx. 5 min with good resolution (Rs > 5) and precision (RSD ≤ 0.6 %). Monolithic columns showed, however, a higher number of theoretical plates, better precision and lower column backpressure than the fused core column. The three developed methods were successfully applied to separate and quantitate fat-soluble vitamins in commercial products.

  19. Comparing monolithic and fused core HPLC columns for fast chromatographic analysis of fat-soluble vitamins

    Directory of Open Access Journals (Sweden)

    Kurdi Said El

    2017-06-01

    Full Text Available HPLC stationary phases of monolithic and fused core type can be used to achieve fast chromatographic separation as an alternative to UPLC. In this study, monolithic and fused core stationary phases are compared for fast separation of four fat-soluble vitamins. Three new methods on the first and second generation monolithic silica RP-18e columns and a fused core pentafluoro-phenyl propyl column were developed. Application of three fused core columns offered comparable separations of retinyl palmitate, DL-α-tocopheryl acetate, cholecalciferol and menadione in terms of elution speed and separation efficiency. Separation was achieved in approx. 5 min with good resolution (Rs > 5 and precision (RSD ≤ 0.6 %. Monolithic columns showed, however, a higher number of theoretical plates, better precision and lower column backpressure than the fused core column. The three developed methods were successfully applied to separate and quantitate fat-soluble vitamins in commercial products.

  20. Fused salt electrolysis

    International Nuclear Information System (INIS)

    Ares, Osvaldo; Botbol, Jose.

    1989-01-01

    Working conditions for zirconium preparation by fused salt electrolysis were studied. For such purpose, a cell was built for operation under argon atmosphere. A graphite crucible served as anode, with steel cathodes. Proper design allowed cathode rechange under the inert atmosphere. Cathodic deposits of zirconium powder occluded salts from the bath. After washing with both water and hydrochloric acid, the metallic powder was consolidated by fusion. Optimum operating conditions were found to arise from an electrolyte of 12% potassium hexafluorzirconate -88% sodium chloride, at 820 deg C and 5 A/cm 2 cathodic current density. Deposits contained 35% of metal and current efficiency reached 66%. The powder contained up to 600 ppm of chlorine and 1.700 ppm of fluorine; after fusion, those amounts decreased to 2 ppm and 3 ppm respectively, with low proportion of metallic impurities. Though oxygen proportion was 4.500 ppm, it should be lowered by improving working conditions, as well as working on an ampler scale. (Author)

  1. Cleaning, abrasion, and polishing effect of novel perlite toothpaste abrasive.

    Science.gov (United States)

    Wang, Bo

    2013-01-01

    This study was intended to optimize perlite particle size and morphology for better tooth cleaning and lower tooth abrasion, and to evaluate the performance of a whitening toothpaste containing the optimized perlite abrasive for tooth cleaning, abrasion, and polishing. Perlite toothpaste abrasive samples were prepared by air classifying a commercial expanded perlite product. The tooth cleaning and abrasion properties for these classified perlite samples were reported via the pellicle cleaning ratio (PCR) and relative dentin abrasion (RDA). Performance of the whitening toothpaste containing the optimized perlite abrasive in tooth cleaning, polishing, and abrasion was evaluated against a widely used synthetic high-cleaning silica. Air classification removes large perlite particles and also physically changes perlite particle morphology from mostly three dimensional and angular particles to mainly two dimensional and platy particles. All the classified samples show good tooth cleaning effect, but tooth abrasion decreases significantly with decreasing particle size. Compared to high-cleaning silica whitening toothpaste, the whitening toothpaste containing the optimized perlite abrasive (PerlClean) is slightly better at tooth cleaning, lower in tooth abrasion, and significantly better at tooth polishing. Fine platy perlite particles are effective in tooth cleaning with low tooth abrasion. The enhanced performance of optimized perlite toothpaste abrasive compared to high-cleaning silica in a whitening toothpaste is attributed to the optimized particle size distribution and the unique platy particle geometry.

  2. Laser polishing of 3D printed mesoscale components

    Energy Technology Data Exchange (ETDEWEB)

    Bhaduri, Debajyoti, E-mail: debajyoti.bhaduri@gmail.com [Department of Mechanical Engineering, School of Engineering, University of Birmingham, Edgbaston, Birmingham, B15 2TT (United Kingdom); Penchev, Pavel; Batal, Afif; Dimov, Stefan; Soo, Sein Leung [Department of Mechanical Engineering, School of Engineering, University of Birmingham, Edgbaston, Birmingham, B15 2TT (United Kingdom); Sten, Stella; Harrysson, Urban [Digital Metal, Höganäs AB, 263 83 Höganäs (Sweden); Zhang, Zhenxue; Dong, Hanshan [School of Metallurgy and Materials, University of Birmingham, Edgbaston, Birmingham, B15 2TT (United Kingdom)

    2017-05-31

    Highlights: • Process optimisation for laser polishing novel 3D printed SS316L parts. • Evaluating the effects of key polishing parameters on SS316L surface roughness. • Detailed spectroscopic analysis of oxide layer formation due to laser polishing. • Comparative surface integrity analysis of SS parts polished in air and argon. • A maximum reduction in roughness of over 94% achieved at optimised polishing settings. - Abstract: Laser polishing of various engineered materials such as glass, silica, steel, nickel and titanium alloys, has attracted considerable interest in the last 20 years due to its superior flexibility, operating speed and capability for localised surface treatment compared to conventional mechanical based methods. The paper initially reports results from process optimisation experiments aimed at investigating the influence of laser fluence and pulse overlap parameters on resulting workpiece surface roughness following laser polishing of planar 3D printed stainless steel (SS316L) specimens. A maximum reduction in roughness of over 94% (from ∼3.8 to ∼0.2 μm S{sub a}) was achieved at the optimised settings (fluence of 9 J/cm{sup 2} and overlap factors of 95% and 88–91% along beam scanning and step-over directions respectively). Subsequent analysis using both X-ray photoelectron spectroscopy (XPS) and glow discharge optical emission spectroscopy (GDOES) confirmed the presence of surface oxide layers (predominantly consisting of Fe and Cr phases) up to a depth of ∼0.5 μm when laser polishing was performed under normal atmospheric conditions. Conversely, formation of oxide layers was negligible when operating in an inert argon gas environment. The microhardness of the polished specimens was primarily influenced by the input thermal energy, with greater sub-surface hardness (up to ∼60%) recorded in the samples processed with higher energy density. Additionally, all of the polished surfaces were free of the scratch marks, pits, holes

  3. Impact of environmental contamination on laser induced damage of silica optics in Laser MegaJoule; Impact de l'environnement sur l'endommagement laser des optiques de silice du Laser MegaJoule

    Energy Technology Data Exchange (ETDEWEB)

    Bien-Aime, K.

    2009-11-15

    Laser induced damage impact of molecular contamination on fused polished silica samples in a context of high power laser fusion facility, such as Laser MegaJoule (LMJ) has been studied. One of the possible causes of laser induced degradation of optical component is the adsorption of molecular or particular contamination on optical surfaces. In the peculiar case of LMJ, laser irradiation conditions are a fluence of 10 J/cm{sup 2}, a wavelength of 351 nm, a pulse duration of 3 ns for a single shot/days frequency. Critical compounds have been identified thanks to environmental measurements, analysis of material outgassing, and identification of surface contamination in the critical environments. Experiments of controlled contamination involving these compounds have been conducted in order to understand and model mechanisms of laser damage. Various hypotheses are proposed to explain the damage mechanism. (author)

  4. Polish Semantic Parser

    Directory of Open Access Journals (Sweden)

    Agnieszka Grudzinska

    2000-01-01

    Full Text Available Amount of information transferred by computers grows very rapidly thus outgrowing the average man's capability of reception. It implies computer programs increase in the demand for which would be able to perform an introductory classitication or even selection of information directed to a particular receiver. Due to the complexity of the problem, we restricted it to understanding short newspaper notes. Among many conceptions formulated so far, the conceptual dependency worked out by Roger Schank has been chosen. It is a formal language of description of the semantics of pronouncement integrated with a text understanding algorithm. Substantial part of each text transformation system is a semantic parser of the Polish language. It is a module, which as the first and the only one has an access to the text in the Polish language. lt plays the role of an element, which finds relations between words of the Polish language and the formal registration. It translates sentences written in the language used by people into the language theory. The presented structure of knowledge units and the shape of understanding process algorithms are universal by virtue of the theory. On the other hand the defined knowledge units and the rules used in the algorithms ure only examples because they are constructed in order to understand short newspaper notes.

  5. Evaluation of oxide-chemical mechanical polishing characteristics using ceria-mixed abrasive slurry

    Science.gov (United States)

    Lee, Youngkyun; Seo, Yong-Jin; Jeong, Haedo

    2012-10-01

    Chemical-mechanical polishing (CMP) characteristics of mixed abrasive slurry (MAS) were studied which was retreated by adding of Ceria (CeO2) abrasives within 1:10 diluted silica slurry (DSS). The slurry was designed for optimal performance which produces reasonable removal rate, acceptable polishing selectivity with respect to underlying layer, low surface defects after polishing, and good slurry stability. The modified abrasives in MAS are evaluated with respect to their particle size distribution, surface morphology, and CMP performances such as removal rate and non-uniformity. As an experimental result, we could obtain successful slurry characteristics compared with traditional silica slurry in the viewpoint of removal rate and non-uniformity.

  6. Laser polishing of 3D printed mesoscale components

    Science.gov (United States)

    Bhaduri, Debajyoti; Penchev, Pavel; Batal, Afif; Dimov, Stefan; Soo, Sein Leung; Sten, Stella; Harrysson, Urban; Zhang, Zhenxue; Dong, Hanshan

    2017-05-01

    Laser polishing of various engineered materials such as glass, silica, steel, nickel and titanium alloys, has attracted considerable interest in the last 20 years due to its superior flexibility, operating speed and capability for localised surface treatment compared to conventional mechanical based methods. The paper initially reports results from process optimisation experiments aimed at investigating the influence of laser fluence and pulse overlap parameters on resulting workpiece surface roughness following laser polishing of planar 3D printed stainless steel (SS316L) specimens. A maximum reduction in roughness of over 94% (from ∼3.8 to ∼0.2 μm Sa) was achieved at the optimised settings (fluence of 9 J/cm2 and overlap factors of 95% and 88-91% along beam scanning and step-over directions respectively). Subsequent analysis using both X-ray photoelectron spectroscopy (XPS) and glow discharge optical emission spectroscopy (GDOES) confirmed the presence of surface oxide layers (predominantly consisting of Fe and Cr phases) up to a depth of ∼0.5 μm when laser polishing was performed under normal atmospheric conditions. Conversely, formation of oxide layers was negligible when operating in an inert argon gas environment. The microhardness of the polished specimens was primarily influenced by the input thermal energy, with greater sub-surface hardness (up to ∼60%) recorded in the samples processed with higher energy density. Additionally, all of the polished surfaces were free of the scratch marks, pits, holes, lumps and irregularities that were prevalent on the as-received stainless steel samples. The optimised laser polishing technology was consequently implemented for serial finishing of structured 3D printed mesoscale SS316L components. This led to substantial reductions in areal Sa and St parameters by 75% (0.489-0.126 μm) and 90% (17.71-1.21 μm) respectively, without compromising the geometrical accuracy of the native 3D printed samples.

  7. Thermal annealing of femtosecond laser written structures in silica glass

    NARCIS (Netherlands)

    Witcher, J.J.; Reichman, W.B.; Fletcher, L.B.; Troy, N.W.; Krol, D.M.

    2013-01-01

    We have investigated the thermal stability of femtosecond laser modification inside fused silica. Raman and FL spectroscopy show that fs-laser induced non-bridging oxygen hole center (NBOHC) defects completely disappear at 300 °C, whereas changes in Si-O ring structures only anneal out after heat

  8. Liquefier Dynamics in Fused Deposition

    DEFF Research Database (Denmark)

    Bellini, Anna; Guceri, Selcuk; Bertoldi, Maurizio

    2004-01-01

    Layered manufacturing (LM) is an evolution of rapid prototyping (RP) technology whereby a part is built in layers. Fused deposition modeling (FDM) is a particular LM technique in which each section is fabricated through vector style deposition of building blocks, called roads, which...

  9. Electric fuses operation, a review: 2. Arcing period

    International Nuclear Information System (INIS)

    Bussière, W

    2012-01-01

    In the electric fuse operation the arcing period follows immediately the pre-arcing period depicted in Part 1 (Part 1. Pre-arcing period). The transition between these two operation steps is not fully understood at this time. To simplify the beginning of the arcing period can be identified with the electric arc ignition i.e. with the electrodes voltage drop. The consecutive plasma is of metallic type at the beginning of the arcing period and of metallic plus silica type with varying mixture up to the end of the arcing period. The energy brought by the fault current is withdrawn by means of the interaction between the electric arc and the arc quenching material (usually silica sand) whose morphometric properties influence the properties of the plasma column: composition, thermodynamic properties and transport coefficients of the plasma column depend on the porosity (and other morphometric properties) of the filler. The fuse element erosion also known as burn-back is responsible for the lengthening of the plasma column and the variations of the electric field. The whole of these processes is depicted by means of experimental results or modellings when possible.

  10. [Lysenkoism in Polish botany].

    Science.gov (United States)

    Köhler, Piotr

    2008-01-01

    Lysenkoism in Poland was never an autonomous phenomenon. The whole array of reasons for which it appeared in Polish science would require a separate study--here it only needs to be pointed out that the major reasons included terror on the part of the security service, lawlessness, the ubiquitous atmosphere of intimidation and terror, censorship, the diminishing sphere of civil liberties, political show trials, propaganda and denunciations. An important role in facilitating the introduction of Lysenkoism was played also by the reorganization of science after World War Two, the isolation of Polish science from science in the West, as well as the damage it had suffered during the war. At first, Lysenkoism was promoted in Poland by a small group of enthusiastic and uncritical proponents. A overview of the events connected with the ten years of Lysenkoism in Poland (end of 1948--beginning of 1958) shows a two-tier picture of how the 'idea' was propagated. The first tier consisted in the activities of the Association of Marxist Naturalists [Koło Przyrodników-Marksistów], which it engaged in since the end of 1948. The Association was later transformed into a Union of Marxist Naturalists, and this in turn merged, in 1952, with the Copernican Society of Polish Naturalists [Polskie Towarzystwo Przyrodników im. Kopernika]. It was that society which promoted Lysenkoism longest, until the end of 1956. The propaganda and training activities of the circle and the society prepared ground for analogous activities of the newly formed Polish Academy of Science (PAN), which--since its very establishment in 1952--engaged in promoting Lysenkoism through its Second Division. These activities were aimed at naturalists, initially at those who were prominent scientists (eg. the conference at Kuźnice, 1950/1951), and then at those who were only starting their academic career (including national courses in new biology at Dziwnów, 1952, or Kortowo, 1953 and 1955). The end to promoting

  11. Subjective Quality of Life of Polish, Polish-Immigrant, and Polish-American Elderly.

    Science.gov (United States)

    Berdes, Celia; Zych, Adam A.

    2000-01-01

    Compares subjective quality of life of elderly Poles living in Poland, and Polish immigrants and Polish-American ethnics living in Chicago as part of a secondary data analysis of a study initially conducted in Poland. Conclusions lend support to the idea that U.S.-born elderly people and elderly immigrants to the United States have a significantly…

  12. Tooth polishing: The current status

    Directory of Open Access Journals (Sweden)

    Madhuri Alankar Sawai

    2015-01-01

    Full Text Available Healthy teeth and gums make a person feel confident and fit. As people go about their daily routines and with different eating and drinking habits, the tooth enamel turns yellowish or gets stained. Polishing traditionally has been associated with the prophylaxis procedure in most dental practices, which patients know and expect. However, with overzealous use of polishing procedure, there is wearing of the superficial tooth structure. This would lead to more accumulation of local deposits. Also, it takes a long time for the formation of the fluoride-rich layer of the tooth again. Hence, now-a-days, polishing is not advised as a part of routine oral prophylaxis procedure but is done selectively based on the patients′ need. The article here, gives an insight on the different aspects of the polishing process along with the different methods and agents used for the same.

  13. Lysenko affair and Polish botany.

    Science.gov (United States)

    Köhler, Piotr

    2011-01-01

    This article describes the slight impact of Lysenkoism upon Polish botany. I begin with an account of the development of plant genetics in Poland, as well as the attitude of scientists and the Polish intelligentsia toward Marxist philosophy prior to the World War II. Next I provide a short history of the introduction and demise of Lysenkoism in Polish science, with a focus on events in botany, in context with key events in Polish science from 1939 to 1958. The article outlines the little effects of Lysenkoism upon botanists and their research, as well as how botanists for the most part rejected what was often termed the "new biology." My paper shows that though Lysenko's theories received political support, and were actively promoted by a small circle of scientists and Communist party activists, they were never accepted by most botanists. Once the political climate in Poland altered after the events of 1956, Lysenko's theories were immediately abandoned.

  14. Elastic emission polishing

    Energy Technology Data Exchange (ETDEWEB)

    Loewenthal, M.; Loseke, K.; Dow, T.A.; Scattergood, R.O.

    1988-12-01

    Elastic emission polishing, also called elastic emission machining (EEM), is a process where a stream of abrasive slurry is used to remove material from a substrate and produce damage free surfaces with controlled surface form. It is a noncontacting method utilizing a thick elasto-hydrodynamic film formed between a soft rotating ball and the workpiece to control the flow of the abrasive. An apparatus was built in the Center, which consists of a stationary spindle, a two-axis table for the workpiece, and a pump to circulate the working fluid. The process is controlled by a programmable computer numerical controller (CNC), which presently can operate the spindle speed and movement of the workpiece in one axis only. This apparatus has been used to determine material removal rates on different material samples as a function of time, utilizing zirconium oxide (ZrO{sub 2}) particles suspended in distilled water as the working fluid. By continuing a study of removal rates the process should become predictable, and thus create a new, effective, yet simple tool for ultra-precision mechanical machining of surfaces.

  15. THE POLISH RECIPE

    Directory of Open Access Journals (Sweden)

    D.F. Spinu

    2017-06-01

    Full Text Available Twenty-six years ago the international community witnessed one of the most dramatic changes in economic systems. Naturally, the fall of communism in Eastern Europe and its consequences were events difficult to judge and anticipate in their immediate aftermath. Today, we have gained a much more coherent perspective on their meaning. The political liberalization of Poland in 1989 and its transition to the market economy was generally perceived as the most successful of all post-communist countries. From 1990 to 2013, Poland experienced the most outstanding economic growth within the former communist bloc. It doubled its GDP in real terms and became the only country to experience economic growth during the financial crisis of 2008-09. However, the polish secret recipe lies in the "shock therapy" adopted at the beginning of the 90's. The aim of this paper is to examine the importance of the Balcerowicz's program in creating the basis for economic stability and growth through privatization, liberalization of foreign trade, monetary reform and an open economy. We will also review the impact of this unprecedented transformation in shaping a strong, market-oriented economy.

  16. Tribochemical interaction between nanoparticles and surfaces of selective layer during chemical mechanical polishing

    Energy Technology Data Exchange (ETDEWEB)

    Ilie, Filip, E-mail: filip@meca.omtr.pub.ro [Polytechnic University of Bucharest, Department of Machine Elements and Tribology (Romania)

    2013-11-15

    Nanoparticles have been widely used in polish slurries such as those in the chemical mechanical polishing (CMP) process. For understanding the mechanisms of CMP, an atomic force microscope (AFM) is used to characterize polished surfaces of selective layers, after a set of polishing experiments. To optimize the CMP polishing process, one needs to get information on the interaction between the nano-abrasive slurry nanoparticles and the surface of selective layer being polished. The slurry used in CMP process of the solid surfaces is slurry with large nanoparticle size colloidal silica sol nano-abrasives. Silica sol nano-abrasives with large nanoparticle are prepared and characterized by transmission electron microscopy, particles colloidal size, and Zeta potential in this paper. The movement of nanoparticles in liquid and the interaction between nanoparticles and solid surfaces coating with selective layer are very important to obtain an atomic alloy smooth surface in the CMP process. We investigate the nanoparticle adhesion and removal processes during CMP and post-CMP cleaning. The mechanical interaction between nanoparticles and the wafer surface was studied using a microcontact wear model. This model considers the nanoparticle effects between the polishing interfaces during load balancing. Experimental results on polishing and cleaning are compared with numerical analysis. This paper suggests that during post-CMP cleaning, a combined effort in chemical and mechanical interaction (tribochemical interactions) would be effective in removal of small nanoparticles during cleaning. For large nanoparticles, more mechanical forces would be more effective. CMP results show that the removal rate has been improved to 367 nm/min and root mean square (RMS) of roughness has been reduced from 4.4 to 0.80 nm. Also, the results show that the silica sol nano-abrasives about 100 nm are of higher stability (Zeta potential is −65 mV) and narrow distribution of nanoparticle

  17. Chemical mechanical polishing (CMP) of sapphire

    Science.gov (United States)

    Zhu, Honglin

    The concept of chemical mechanical polishing (CMP) was examined for finishing sapphire. In this study sapphire was used as a model system for oxide ceramics. The removal rates were determined by weight loss. Surface quality and structure were characterized with surface probe microscopy (SPM). Polishing experiments were designed to test the chemically modified surface layer. A series of abrasives with various hardnesses including mono-crystalline and polycrystalline diamond, alpha and gamma alumina, zirconia, ceria and silica were used. Diaspore was also evaluated. The results indicated that, with similar particle size and shape, harder abrasives do not necessarily cause faster material removal and better surface finish, and abrasives with hardness equal to or less than sapphire such as alpha alumina and gamma alumina achieved the best surface finish and efficient material removal. A hypothesis was proposed that the sapphire surface was modified by water to form a thin hydration laver with structure and hardness close to diaspore. Abrasives with a hardness between diaspore and sapphire polished the c-plane of sapphire with good surface finish and efficient removal. SPM indicated the hydration layer on the c-plane surface was about 1 nm thick. Removal rate and surface finish as a function of pH were also examined on c-plane sapphire with nano-alumina abrasives. The removal rate as a function of pH was compared to the solubility behavior of alumina. The results showed the deviation of pH from the lowest solubility pH for alumina (pH = 5) was a driving force for the surface reaction to form a hydration layer. The anisotropy of sapphire strongly affects removal rate and surface quality in CMP. The relationships among orientation. pH and abrasive were studied for sapphire with c (0001), a (11-20), and m (10-10) planes. Based on the results, the CMP process for sapphire includes chemical reaction of the surface to form a thin reaction layer that is softer than sapphire

  18. Polish Toxic Currency Options

    Directory of Open Access Journals (Sweden)

    Waldemar Gontarski

    2009-04-01

    Full Text Available Toxic currency options are defined on the basis of the opposition to the nature (essence of an option contract, which is justified in terms of norms founded on the general law clause of characteristics (nature of a relation (which represents an independent premise for imposing restrictions on the freedom of contracts. So-understood toxic currency options are unlawful. Indeed they contravene iuris cogentis regulations. These include for instance option contracts, which are concluded with a bank, if the bank has not informed about option risk before concluding the contract; or the barrier options, which focus only on the protection of banks interests. Therefore, such options may appear to be invalid. Therefore, performing contracts for toxic currency options may be qualified as a criminal mismanagement. For the sake of security, the manager should then take into consideration filing a claim for stating invalidity (which can be made in a court verdict. At the same time, if the supervisory board member in a commercial company, who can also be a subject to mismanagement offences, commits an omission involving lack of reaction (for example, if he/she fails to notify of the suspected offence committed by the management board members acting to the companys detriment when the management board makes the company conclude option contracts which are charged with absolute invalidity the supervisory board member so acting may be considered to act to the companys detriment. In the most recent Polish jurisprudence and judicature the standard of a good host is treated to be the last resort for determining whether the managers powers resulting from criminal regulations were performed. The manager of the exporter should not, as a rule, issue any options. Issuing options always means assuming an obligation. In the case of currency put options it is an absolute obligation to purchase a given amount in euro at exchange rate set in advance. On the other hand issuing

  19. FUSE Mission Overview and Status

    Science.gov (United States)

    Sonneborn, G.

    The Far Ultraviolet Spectroscopic Explorer satellite observes light in the 905-1187 Å region with high spectral resolution (λ/Δλ ~ 20,000). FUSE was launched on 24 June 1999 and the early observations have yielded significant results in several areas of galactic and extragalactic astronomy. The sensitivity is sufficient to examine reddened lines of sight within the Milky Way as well as active galactic nuclei and QSOs for absorption line studies of both Milky Way and extragalactic gas clouds. This spectral region contains a number of important scientific diagnostics, including O VI, H I, D I, and the strong electronic transitions of the H2 and HD molecules. The instrument has four coaligned prime-focus telescopes and Rowland spectrographs with microchannel plate detectors. Two channels use Al:LiF coatings for optimum reflectivity from ~ 1000 to 1187 Å and the other two use SiC coatings for optimized throughput between 905 and 1105 Å. The gratings were holographically ruled to largely correct for astigmatism and to minimize scattered light. The detectors have KBr photocathodes and use photon counting to achieve good quantum efficiency with low background signal. The primary mission duration is three years; an extended mission phase is planned. A majority of the observing time is allocated to guest observers. (http://fuse.pha.jhu.edu)

  20. About a New Type of Fuse Based on the Controllable Fusing Effect

    Directory of Open Access Journals (Sweden)

    PLESCA, A.

    2009-06-01

    Full Text Available Fuses are among the best known of electrical devices and there are an extremely large number in use throughout the world. Beside of the advantageous features, the nowadays fuses have certain drawbacks. Therefore, a new type of fuse based on controllable fusing concept is proposed and a study as regards the total clearing time is done. The new concept has been validated through many experimental tests at different current values. The new type of fuse based on controllable fusing concept can be integrated within an overcurrent protection system especially to protect power semiconductors where the Joule integral criterion is better satisfied.

  1. Effects of different polishing techniques on the surface roughness of dental porcelains

    Directory of Open Access Journals (Sweden)

    Işil Sarikaya

    2010-02-01

    Full Text Available OBJECTIVE: The purpose of this study was to evaluate the effects of different polishing techniques on the surface roughness of dental porcelains. MATERIAL AND METHODS: Fifty-five cylindirical specimens (15x2 mm were prepared for each feldspathic (Vita VMK 95, Ceramco III and low-fusing dental porcelain (Matchmaker. Fifty-five specimens of machinable feldspathic porcelain blocks (Vitablocs Mark II, (12x14x18 mm were cut into 2-mm-thick slices (12x14 mm with low speed saw. The prepared specimens were divided into 11 groups (n=5 representing different polishing techniques including control ((C no surface treatment, glaze (G and other 9 groups that were finished and polished with polishing discs (Sof-Lex (Sl, two porcelain polishing kits (NTI (Pk, Dialite II (Di, a diamond polishing paste (Sparkle (Sp, a zirconium silicate based cleaning and polishing prophy paste (Zircate (Zr, an aluminum oxide polishing paste (Prisma Gloss (Pg, and combinations of them. The surface roughness of all groups was measured with a profilometer. The data were analyzed with a 2-way analysis of variance, and the mean values were compared by the Tukey Honestly Significant Difference test (a=0.05. RESULTS: For all porcelain material groups, the lowest Ra values were observed in Group Gl, Group Sl, Group Pk, and Group Di, which were not significantly different from each other (p>0.05.When comparing the 4 different porcelain materials, the machinable feldspathic porcelain block group (Mark II demonstrated statistically significantly less Ra values than the other porcelain materials tested (p<0.05. No significant difference was observed between the VMK 95 and Ceramco III porcelain groups (p=0.919, also these groups demonstrated the highest Ra values. CONCLUSION: Subjected to surface roughness, the surfaces obtained with polishing and/or cleaning-prophy paste materials used alone were rougher compared to the surfaces finished using Sof-lex, Dialite, and NTI polishing kit

  2. Efficient polishing of aspheric optics

    Energy Technology Data Exchange (ETDEWEB)

    Taylor, J.S.; Piscotty, M.A.; Nguyen, N.Q.; Landram, C.S.; Ng, L.C.

    1997-04-15

    The objectives of this project are to develop, evaluate, and optimize novel designs for a polishing tool intended for ultra-precise figure corrections on aspheric optics with tolerances typical of those required for use in extreme ultraviolet (EUV) projection lithography. This work may lead to an enhanced US industrial capability for producing optics for EUV, x-ray and, other high precision applications. LLNL benefits from developments in computer-controlled polishing and the insertion of fluid mechanics modeling into the precision manufacturing area. Our accomplishments include the numerical estimation of the hydrodynamic shear stress distribution for a new polishing tool that directs and controls the interaction of an abrasive slurry with an optical surface. A key milestone is in establishing a correlation between the shear stress predicted using our fluid mechanics model and the observed removal footprint created by a prototype tool. In addition, we demonstrate the ability to remove 25 nm layers of optical glass in a manner qualitatively similar to macroscopic milling operations using a numerically- controlled machine tool. Other accomplishments include the development of computer control software for directing the polishing tool and the construction of a polishing testbed.

  3. Use of low fusing alloy in dentistry.

    Science.gov (United States)

    Wee, A G; Schneider, R L; Aquilino, S A

    1998-11-01

    Low fusing alloy has been used in dentistry for remount procedures in both fixed and removable prosthodontics, in implant prosthodontics for the fabrication of solid implant casts, in maxillofacial prosthetics as oral radiation shields, and in dental research for its unique properties. Previously, the use of low fusing alloy was thought to offer a high degree of dimensional accuracy. However, multiple in vitro studies have shown that its presumed dimensional accuracy may be questionable. This article reviews the physical properties, metallurgical considerations of low fusing alloy, its applications in dentistry, and a safe, simple method of using low fusing alloy.

  4. Compact 3D photonic crystals sensing platform with 45 degree angle polished fibers

    Science.gov (United States)

    Guo, Yuqing; Chen, Lu; Zhu, Jiali; Ni, Haibin; Xia, Wei; Wang, Ming

    2017-07-01

    Three dimensional photonic crystals are a kind of promising sensing materials in biology and chemistry. A compact structure, consists of planner colloidal crystals and 45 degree angle polished fiber, is proposed as a platform for accurate, fast, reliable three dimensional photonic crystals sensing in practice. This structure show advantages in compact size for integration and it is ease for large scale manufacture. Reflectivity of the 45 degree angle polished surface with and without a layer of Ag film are simulated by FDTD simulation. Refractive index sensing properties as well as mode distribution of this structure consists of both polystyrene opal and silica inverse opal film is investigated, and an experimental demonstration of silica inverse opal film is performed, which shows a sensitivity of 733 nm/RIU. Different kinds of three dimensional photonic crystals can also be applied in this structure for particular purpose.

  5. Preparation of spherical ceria coated silica nanoparticle abrasives for CMP application

    Science.gov (United States)

    Peedikakkandy, Lekha; Kalita, Laksheswar; Kavle, Pravin; Kadam, Ankur; Gujar, Vikas; Arcot, Mahesh; Bhargava, Parag

    2015-12-01

    This paper describes synthesis of spherical and highly mono-dispersed ceria coated silica nanoparticles of size ∼70-80 nm for application as abrasive particles in Chemical Mechanical Planarization (CMP) process. Core silica nanoparticles were initially synthesized using micro-emulsion method. Ceria coating on these ultrafine and spherical silica nanoparticles was achieved using controlled chemical precipitation method. Study of various parameters influencing the formation of ceria coated silica nanoparticles of size less than 100 nm has been undertaken and reported. Ceria coating over silica nanoparticles was varied by controlling the reaction temperature, pH and precursor concentrations. Characterization studies using X-ray diffraction, scanning electron microscopy, transmission electron microscopy and Energy Dispersive X-ray analysis show formation of crystalline CeO2 coating of ∼10 nm thickness over silica with spherical morphology and particle size slurry of ceria coated silica abrasive was prepared and employed for polishing of oxide and nitride films on silicon substrates. Polished films were studied using ellipsometry and an improvement in SiO2:SiN selective removal rates up to 12 was observed using 1 wt% ceria coated silica nanoparticles slurry.

  6. Dissolved air flotation of polishing wastewater from semiconductor manufacturer.

    Science.gov (United States)

    Liu, J C; Lien, C Y

    2006-01-01

    The feasibility of the dissolved air flotation (DAF) process in treating chemical mechanical polishing (CMP) wastewater was evaluated in this study. Wastewater from a local semiconductor manufacturer was sampled and characterised. Nano-sized silica (77.6 nm) with turbidity of 130 +/- 3 NTU was found in the slightly alkaline wastewater with traces of other pollutants. Experimental results indicated removal efficiency of particles, measured as suspended particle or turbidity, increased with increasing concentration of cationic collector cetyltrimethyl ammonium bromide (CTAB). When CTAB concentration was 30 mg/L, pH of 6.5 +/- 0.1 and recycle ratio of 30%, very effective removal of particles (> 98%) was observed in saturation pressure range of 4 to 6 kg/cm2, and the reaction proceeded faster under higher pressure. Similarly, the reaction was faster under the higher recycle ratio, while final removal efficiency improved slightly as the recycle ratio increased from 20 to 40%. An insignificant effect of pH on treatment efficiency was found as pH varied from 4.5 to 8.5. The presence of activator, Al3+ and Fe3+, enhanced the system performance. It is proposed that CTAB adsorbs on silica particles in polishing wastewater through electrostatic interaction and makes particles more hydrophobic. The increase in hydrophobicity results in more effective bubble-particle collisions. In addition, flocculation of silica particles through bridging effect of collector was found; it is believed that flocculation of particles also contributed to flotation. Better attachment between gas bubble and solid, higher buoyancy and higher air to solid ratio all lead to effective flotation.

  7. Cannabinoids cases in polish athletes

    OpenAIRE

    A Pokrywka; Z Obmiński; D Kwiatkowska; R Grucza

    2009-01-01

    The aim of this study was to investigate the number of cases and the profiles of Polish athletes who had occasionally been using marijuana or hashish throughout the period of 1998-2004, with respect to: sex, age, and discipline of sport as well as the period of testing (in- and out-of-competition). Results of the study were compared with some data reported by other WADA accredited anti-doping laboratories. Totally, 13 631 urine samples taken from Polish athletes of both sexes, aged 10-67 year...

  8. Transplantation of Crossed Fused Renal Ectopia

    Directory of Open Access Journals (Sweden)

    Soon-Khai Lee

    2007-01-01

    Full Text Available Crossed fused renal ectopia is a type of congenital fused anomaly of the kidney. This type of kidney, when encountered, can be used as a donor organ to provide useful solution to the critical shortage of available organs for transplantation.

  9. Polish-Bulgarian-Russian, Bulgarian-Polish-Russian or Russian-Bulgarian-Polish dictionary?

    Directory of Open Access Journals (Sweden)

    Violetta Koseska-Toszewa

    2015-11-01

    Full Text Available Polish-Bulgarian-Russian, Bulgarian-Polish-Russian or Russian-Bulgarian-Polish dictionary? The trilingual dictionary (M. Duszkin, V. Koseska, J. Satoła and A. Tzoneva is being elaborated based on a working Polish-Bulgarian-Russian electronic parallel corpus authored by Maksim Duszkin, Violetta Koseska-Toszewa and Joanna Satoła-Staśkowiak, and works by A. Tzoneva. It is the first corpus comparing languages belonging to three different Slavic language groups: western, southern and eastern. Works on the dictionary are based on Gramatyka konfrontatywna bułgarsko-polska (Bulgarian-Polish confrontative grammar and the proposed there semantic-oriented interlanguage. Two types of classifiers have been introduced into the dictionary: classic and semantic. The trilingual dictionary will present a consistent and homogeneous set of facts of grammar and semantics. The Authors point out that in a traditional dictionary it is not clear for example whether aspect should be understood as imperfective / perfective form of a verb or as its meaning. Therefore in the dictionary forms and meaning are separated in a regular way. Imperfective verb form has two meanings: state and configuration of states and events culminating in state. Also perfective verb form has two meanings: event and configuration of states and events culminating in event. These meanings are described by the semantic classifiers, respectively, state and event, state1 and event1. The way of describing language units, mentioned in the article, gives a possibility to present language material (Polish, Bulgarian, Russian in any required order, hence the article’s title.

  10. Cannabinoids cases in polish athletes

    Directory of Open Access Journals (Sweden)

    A Pokrywka

    2009-07-01

    Full Text Available The aim of this study was to investigate the number of cases and the profiles of Polish athletes who had occasionally been using marijuana or hashish throughout the period of 1998-2004, with respect to: sex, age, and discipline of sport as well as the period of testing (in- and out-of-competition. Results of the study were compared with some data reported by other WADA accredited anti-doping laboratories. Totally, 13 631 urine samples taken from Polish athletes of both sexes, aged 10-67 years, performing 46 disciplines of sport were tested. Cannabinoids were detected in 267 samples. Among Polish athletes the relative number of positive THC (tetrahydrocannabinol samples was one of the highest in Europe. The group of young Polish athletes (aged 16-24 years was the most THC-positive. THC-positive cases were noted more frequently in male athletes tested during out of competitions. The so-called contact sports (rugby, ice hockey, skating, boxing, badminton, body building and acrobatic sports were those sports, where the higher risk of cannabis use was observed. The legal interpretation of some positive cannabinoids results would be difficult because of some accidental and unintentional use of the narcotics by sportsmen. It was concluded that national anti-doping organizations (NADO’s, which are competent to judge whether the anti-doping rules were violated, should take into account the possibility of non-intentional doping use of cannabinoids via passive smoking of marijuana.

  11. Sensing roughness and polish direction

    DEFF Research Database (Denmark)

    Jakobsen, Michael Linde; Olesen, Anders Sig; Larsen, Henning Engelbrecht

    2016-01-01

    needs information about the RMS-value of the surface roughness and the current direction of the scratches introduced by the polishing process. The RMS-value indicates to the operator how far he is from the final finish, and the scratch orientation is often specified by the customer in order to avoid...... structures and light scattered from scratches....

  12. The alkali-silica reaction: mineralogical and geochemical aspects of some Dutch concretes and Norwegian mylonites

    NARCIS (Netherlands)

    Broekmans, M.A.T.M.

    2002-01-01

    Maarten Broekmans has studied the alkali-silica reaction in two Dutch concretes by means of optical microscopy, geochemical analyses on bulk material and after selective digestion in acid, and with element mapping in polished thin sections. He furthermore characterized the nature of the

  13. Laser welding of fused quartz

    Science.gov (United States)

    Piltch, Martin S.; Carpenter, Robert W.; Archer, III, McIlwaine

    2003-06-10

    Refractory materials, such as fused quartz plates and rods are welded using a heat source, such as a high power continuous wave carbon dioxide laser. The radiation is optimized through a process of varying the power, the focus, and the feed rates of the laser such that full penetration welds may be accomplished. The process of optimization varies the characteristic wavelengths of the laser until the radiation is almost completely absorbed by the refractory material, thereby leading to a very rapid heating of the material to the melting point. This optimization naturally occurs when a carbon dioxide laser is used to weld quartz. As such this method of quartz welding creates a minimum sized heat-affected zone. Furthermore, the welding apparatus and process requires a ventilation system to carry away the silicon oxides that are produced during the welding process to avoid the deposition of the silicon oxides on the surface of the quartz plates or the contamination of the welds with the silicon oxides.

  14. The potential use of silica sand as nanomaterials for mortar

    Science.gov (United States)

    Setiati, N. Retno

    2017-11-01

    The development of nanotechnology is currently experiencing rapid growth. The use of the term nanotechnology is widely applied in areas such as healthcare, industrial, pharmaceutical, informatics, or construction. By the nanotechnology in the field of concrete construction, especially the mechanical properties of concrete are expected to be better than conventional concrete. This study aims to determine the effect of the potential of silica sand as a nanomaterial that is added into the concrete mix The methodology used consist of nanomaterial synthesis process of silica sand using Liquid Polishing Milling Technology (PLMT). The XRF and XRD testing were conducted to determine the composition of silica contained in the silica sand and the level of reactivity of the compound when added into the concrete mix. To determine the effect of nano silica on mortar, then made the specimen with size 50 mm x 50 mm x 50 mm. The composition of mortar is made in two variations, ie by the addition of 3% nano silica and without the addition of nanosilica. To know the mechanical properties of mortar, it is done testing of mortar compressive strength at the age of 28 days. Based on the analysis and evaluation, it is shown that compounds of silica sand in Indonesia, especially Papua reached more than 99% SiO2 and so that the amorphous character of silica sand can be used as a nanomaterial for concrete construction. The results of mechanical tests show that there is an increase of 12% compressive strength of mortar that is added with 3% nano silica.

  15. Porphyrins Fused with Unactivated Polycyclic Aromatic Hydrocarbons

    KAUST Repository

    Diev, Vyacheslav V.

    2012-01-06

    A systematic study of the preparation of porphyrins with extended conjugation by meso,β-fusion with polycyclic aromatic hydrocarbons (PAHs) is reported. The meso-positions of 5,15-unsubstituted porphyrins were readily functionalized with PAHs. Ring fusion using standard Scholl reaction conditions (FeCl 3, dichloromethane) occurs for perylene-substituted porphyrins to give a porphyrin β,meso annulated with perylene rings (0.7:1 ratio of syn and anti isomers). The naphthalene, pyrene, and coronene derivatives do not react under Scholl conditions but are fused using thermal cyclodehydrogenation at high temperatures, giving mixtures of syn and anti isomers of the meso,β-fused porphyrins. For pyrenyl-substituted porphyrins, a thermal method gives synthetically acceptable yields (>30%). Absorption spectra of the fused porphyrins undergo a progressive bathochromic shift in a series of naphthyl (λ max = 730 nm), coronenyl (λ max = 780 nm), pyrenyl (λ max = 815 nm), and perylenyl (λ max = 900 nm) annulated porphyrins. Despite being conjugated with unsubstituted fused PAHs, the β,meso-fused porphyrins are more soluble and processable than the parent nonfused precursors. Pyrenyl-fused porphyrins exhibit strong fluorescence in the near-infrared (NIR) spectral region, with a progressive improvement in luminescent efficiency (up to 13% with λ max = 829 nm) with increasing degree of fusion. Fused pyrenyl-porphyrins have been used as broadband absorption donor materials in photovoltaic cells, leading to devices that show comparatively high photovoltaic efficiencies. © 2011 American Chemical Society.

  16. Study on planarization machining of sapphire wafer with soft-hard mixed abrasive through mechanical chemical polishing

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Yongchao [Institute of Manufacturing Engineering, Huaqiao University, Xiamen 361021 (China); MOE Engineering Research Center for Brittle Materials Machining, Huaqiao University, Xiamen 361021 (China); Lu, Jing, E-mail: lujing26@hqu.edu.cn [Institute of Manufacturing Engineering, Huaqiao University, Xiamen 361021 (China); MOE Engineering Research Center for Brittle Materials Machining, Huaqiao University, Xiamen 361021 (China); Xu, Xipeng [Institute of Manufacturing Engineering, Huaqiao University, Xiamen 361021 (China); MOE Engineering Research Center for Brittle Materials Machining, Huaqiao University, Xiamen 361021 (China)

    2016-12-15

    Highlights: • Nano-silica abrasive with higher reactivity are prepared by hydrolysis-precipitation. • Polishing performance of soft-hard mixed abrasives during MCP is investigated. • Products of solid state reaction have been further confirmed by a new approach. • Material removal mechanism of sapphire with mixed abrasives is discussed. - Abstract: This study investigated the material removal mechanism of sapphire wafer with soft-hard mixed abrasives through mechanical chemical polishing (MCP). The polishing film, which contains diamond as hard abrasives and high reactivity silica as soft abrasives, is prepared through sol-gel technology. Silica abrasives with regular spherical shape and high reactivity are prepared through hydrolysis-precipitation. Diamond grits with three different particle sizes are used as abrasives. Results show that the rate of material removal of mixed abrasives during MCP is more than 52.6% of that of single hard abrasives and the decrease in surface roughness is more than 21.6% of that of single hard abrasives. These results demonstrate that the ideal planarization of sapphire wafer with high removal rate and good surface quality can be achieved when the effect of mechanical removal of hard abrasives and the chemical corrosion effect of soft abrasives are in dynamic equilibrium. A model that describes the material removal mechanism of sapphire with mixed abrasives during MCP is proposed. The results of thermodynamic calculation and polishing residue analysis are used to demonstrate the rationality of the model.

  17. Dynamic simulation of flywheel-type fuses

    Directory of Open Access Journals (Sweden)

    Editorial Office

    1996-07-01

    Full Text Available Rounds of ammunition are normally armed with a fuse. In this study, a fuse is developed which uses a flywheel-type mechanism controlled by time or distance. Due to its simplicity of operation and construction, the concept is expected to have high reliabil­ity. The dynamic response of all the components of this flywheel-type fuse is mathematically modelled. Simulation software was developed which connects the mathematical models of the various components. With the definition of boundary values, the response of the projectile, flywheel and other components can be determined continuously for firing and in-flight conditions.

  18. Microporous silica membranes

    DEFF Research Database (Denmark)

    Boffa, Vittorio; Yue, Yuanzheng

    2012-01-01

    Hydrothermal stability is a crucial factor for the application of microporous silica-based membranes in industrial processes. Indeed, it is well established that steam exposure may cause densification and defect formation in microporous silica membranes, which are detrimental to both membrane...... permeability and selectivity. Numerous previous studies show that microporous transition metal doped-silica membranes are hydrothermally more stable than pure silica membranes, but less permeable. Here we present a quantitative study on the impact of type and concentration of transition metal ions...... on the microporous structure, stability and permeability of amorphous silica-based membranes, providing information on how to design chemical compositions and synthetic paths for the fabrication of silica-based membranes with a well accessible and highly stabile microporous structure....

  19. Polish energy-system modernisation

    International Nuclear Information System (INIS)

    Drozdz, M.

    2003-01-01

    The Polish energy-system needs intensive investments in new technologies, which are energy efficient, clean and cost effective. Since the early 1990s, the Polish economy has had practically full access to modern technological devices, equipment and technologies. Introducing new technologies is a difficult task for project teams, constructors and investors. The author presents a set of principles for project teams useful in planning and energy modernisation. Several essential features are discussed: Energy-efficient appliances and systems; Choice of energy carriers, media and fuels; Optimal tariffs, maximum power and installed power; Intelligent, integrated, steering systems; Waste-energy recovery; Renewable-energy recovery. In practice there are several difficulties connected with planning and realising good technological and economic solutions. The author presents his own experiences of energy-system modernisation of industrial processes and building new objects. (Author)

  20. FINANCIAL SECURITY OF POLISH HOUSEHOLDS

    Directory of Open Access Journals (Sweden)

    Agnieszka Kozera

    2016-09-01

    Full Text Available  A household’s fi nancial security is essential for the satisfaction of the needs and wants of its members, both communal and individual. It constitutes a kind of foundation for all of a household’s fi nancial decisions that impact its standard of living. The article aims to assess the level of fi nancial security of Polish households in 2005–2013. The research draws on data from Genworth Index, HBS conducted by the Central Statistical Offi ce (GUS and Social Diagnosis (Diagnoza społeczna overseen by the Social Monitoring Council. The study shows that Poland is characterized by a low level of fi nancial security relative to other European countries, especially Western and Scandinavian. More than three-quarters of Polish households experience fi nancial problems and exhibit both a low propensity to save, and low savings rates.

  1. Energy savings in Polish buildings

    Energy Technology Data Exchange (ETDEWEB)

    Markel, L.C.; Gula, A.; Reeves, G.

    1995-12-31

    A demonstration of low-cost insulation and weatherization techniques was a part of phase 1 of the Krakow Clean Fossil Fuels and Energy Efficient Project. The objectives were to identify a cost-effective set of measures to reduce energy used for space heating, determine how much energy could be saved, and foster widespread implementation of those measures. The demonstration project focused on 4 11-story buildings in a Krakow housing cooperative. Energy savings of over 20% were obtained. Most important, the procedures and materials implemented in the demonstration project have been adapted to Polish conditions and applied to other housing cooperatives, schools, and hospitals. Additional projects are being planned, in Krakow and other cities, under the direction of FEWE-Krakow, the Polish Energie Cities Network, and Biuro Rozwoju Krakowa.

  2. Earnings Management in Polish Companies

    OpenAIRE

    Brzeszczyński, Janusz; Gajdka, Jerzy; Schabek, Tomasz

    2012-01-01

    This paper presents results of the investigation of a phenomenon known as "earnings management'' (EM) among the companies listed on the Polish stock market. The distribution of earnings per share (EPS) for the stocks around the threshold value of "zero" and the threshold of "recent performance" was analyzed in the period of years 1997-2010. Moreover, the changes of earnings for the stocks, which are suspected to manipulate their earnings, were also investigated. The results, which indicate as...

  3. LOVE in English and Polish

    Directory of Open Access Journals (Sweden)

    Małgorzata Brożyna Reczko

    2017-12-01

    Full Text Available LOVE in English and Polish The paper presents a sample contrastive analysis of the linguistic picture of love in English and Polish. The material used in the survey is drawn from lexicographic data, including the British National Corpus and Narodowy Korpus Języka Polskiego [National Corpus of Polish]. The paper focuses on the similarities and differences in conceptualizing the abstract concept of love in the English and Polish languages. An analytical method, developed by Bartmiński and associates, serves as the theoretical basis for the reconstruction of the linguistic picture of the world.   MIŁOŚĆ w języku angielskim i polskim Niniejszy artykuł to próba kontrastywnego porównania językowego obrazu świata MIŁOŚCI w języku angielskim i polskim. Materiał badawczy pochodzi głównie ze źródeł leksykograficznych: słowników oraz korpusów (Narodowego Korpusu Języka Polskiego oraz z korpusu języka angielskiego British National Corpus. Celem badania było poszukiwanie podobieństw i różnic w konceptualizacji MIŁOŚCI w tych dwóch językach. Metoda badawcza została zaczerpnięta z prac J. Bartmińskiego i dotyczy rekonstrukcji językowego obrazu świata różnych pojęć.

  4. Study of laser-induced damage on the exit surface of silica components in the nanosecond regime in a multiple wavelengths configuration

    International Nuclear Information System (INIS)

    Chambonneau, Maxime

    2014-01-01

    In this thesis, laser-induced damage phenomenon on the surface of fused silica components is investigated in the nanosecond regime. This phenomenon consists in an irreversible modification of the material. In the nanosecond regime, laser damage is tightly correlated to the presence of non-detectable precursor defects which are a consequence of the synthesis and the polishing of the components. In this thesis, we investigate laser damage in a multiple wavelengths configuration. In order to better understand this phenomenon in these conditions of irradiation, three studies are conducted. The first one focuses on damage initiation. The results obtained in the single wavelength configurations highlight a coupling in the multiple wavelengths one. A comparison between the experiments and a model developed during this thesis enables us to improve the knowledge of the fundamental processes involved during this damage phase. Then, we show that post mortem characterizations of damage morphology coupled to an accurate metrology allow us to understand both the nature and also the chronology of the physical mechanisms involved during damage formation. The proposed theoretical scenario is confirmed through various experiments. Finally, we study damage growth in both the single and the multiple wavelengths cases. Once again, this last configuration highlights a coupling between the wavelengths. We show the necessity to account for the spatial characteristics of the laser beams during a growth session. (author) [fr

  5. XAFS study on silica glasses irradiated in a nuclear reactor

    International Nuclear Information System (INIS)

    Yoshida, Tomoko; Yoshida, Hisao; Hara, Takanobu; Ii, Tatsuya; Okada, Tomohisa; Tanabe, Tetsuo

    2000-01-01

    X-ray absorption technique (XANES and EXAFS) was applied to study the local structures of silica glasses before and after the irradiation in a nuclear reactor. Although our separate photoluminescence (PL) measurements clearly showed the different aspects about oxygen vacancies in these samples, i.e., at least the B 2β type oxygen-deficient center exists as an intrinsic defect in the fused silica glass while another type B 2α center is formed in the synthesized silica glass, such differences did not directly reflect on the X-ray absorption spectra (XANES and EXAFS). However, the curve-fitting analysis of EXAFS showed that the number of oxygen atoms coordinated to Si relatively increased after the irradiation. This result may indicate the occurrence of the structural relaxation in the irradiated samples, that is, a slightly distorted SiO 4 tetrahedra in silica glasses relaxed to the regular SiO 4 tetrahedra due to the break of some connections between SiO 4 units in the silica glasses. Thus, the X-ray absorption technique gave the important information of the in-reactor irradiated silica glasses which complements the results obtained from PL measurements

  6. Coordination chemistry in fused-salt solutions

    Science.gov (United States)

    Gruen, D. M.

    1969-01-01

    Spectrophotometric work on structural determinations with fused-salt solutions is reviewed. Constraints placed on the method, as well as interpretation of the spectra, are discussed with parallels drawn to aqueous spectrophotometric curves of the same materials.

  7. Comparative evaluation of fiber fuse models

    International Nuclear Information System (INIS)

    Davis, D.D.; Mettler, S.C.; DiGiovanni, D.J.

    1997-01-01

    A phenomenon which results in the catastrophic destruction of the guiding properties of an optical fiber has been observed at laser power densities on the order of 3 x 10 6 watts/cm 2 in the core. This phenomenon is characterized by the propagation of a bright visible light from the point of initiation toward the laser source. The term 'fiber fuse' has been used because of the similarity in appearance to a burning fuse. The fiber fuse has been shown to start when the end of the fiber is contacted. It has also been initiated spontaneously from mechanical splices. This paper reports experimental data gathered on the fiber fuse and discusses their relationship to proposed physical mechanisms

  8. 19th Polish Control Conference

    CERN Document Server

    Kacprzyk, Janusz; Oprzędkiewicz, Krzysztof; Skruch, Paweł

    2017-01-01

    This volume contains the proceedings of the KKA 2017 – the 19th Polish Control Conference, organized by the Department of Automatics and Biomedical Engineering, AGH University of Science and Technology in Kraków, Poland on June 18–21, 2017, under the auspices of the Committee on Automatic Control and Robotics of the Polish Academy of Sciences, and the Commission for Engineering Sciences of the Polish Academy of Arts and Sciences. Part 1 deals with general issues of modeling and control, notably flow modeling and control, sliding mode, predictive, dual, etc. control. In turn, Part 2 focuses on optimization, estimation and prediction for control. Part 3 is concerned with autonomous vehicles, while Part 4 addresses applications. Part 5 discusses computer methods in control, and Part 6 examines fractional order calculus in the modeling and control of dynamic systems. Part 7 focuses on modern robotics. Part 8 deals with modeling and identification, while Part 9 deals with problems related to security, fault ...

  9. Directly polished lightweight aluminum mirror

    Science.gov (United States)

    ter Horst, Rik; Tromp, Niels; de Haan, Menno; Navarro, Ramon; Venema, Lars; Pragt, Johan

    2017-11-01

    During the last ten years, Astron has been a major contractor for the design and manufacturing of astronomical instruments for Space- and Earth based observatories, such as VISIR, MIDI, SPIFFI, X-Shooter and MIRI. Driven by the need to reduce the weight of optically ultra-stiff structures, two promising techniques have been developed in the last years: ASTRON Extreme Lightweighting [1][2] for mechanical structures and an improved Polishing Technique for Aluminum Mirrors. Using one single material for both optical components and mechanical structure simplifies the design of a cryogenic instrument significantly, it is very beneficial during instrument test and verification, and makes the instrument insensitive to temperature changes. Aluminum has been the main material used for cryogenic optical instruments, and optical aluminum mirrors are generally diamond turned. The application of a polishable hard top coating like nickel removes excess stray light caused by the groove pattern, but limits the degree of lightweighting of the mirrors due to the bi-metal effect. By directly polishing the aluminum mirror surface, the recent developments at Astron allow for using a non-exotic material for light weighted yet accurate optical mirrors, with a lower surface roughness ( 1nm RMS), higher surface accuracy and reduced light scattering. This paper presents the techniques, obtained results and a global comparison with alternative lightweight mirror solutions. Recent discussions indicate possible extensions of the extreme light weight technology to alternative materials such as Zerodur or Silicon Carbide.

  10. Modeling laser-induced surface cracks in silica at 355 nm

    International Nuclear Information System (INIS)

    Feit, M.D.

    1997-01-01

    Starting from the absorption of laser energy at a subsurface nanoparticle in fused silica, we simulate the consequent buildup of stresses and resulting mechanical material damage . The simulation indicates the formation of micropits with size comparable to a wavelength, similar to experimental observation. Possible mechanisms for enhanced local light absorbtion are discussed

  11. Crystalline Silica Primer

    Science.gov (United States)

    ,

    1992-01-01

    Crystalline silica is the scientific name for a group of minerals composed of silicon and oxygen. The term crystalline refers to the fact that the oxygen and silicon atoms are arranged in a threedimensional repeating pattern. This group of minerals has shaped human history since the beginning of civilization. From the sand used for making glass to the piezoelectric quartz crystals used in advanced communication systems, crystalline silica has been a part of our technological development. Crystalline silica's pervasiveness in our technology is matched only by its abundance in nature. It's found in samples from every geologic era and from every location around the globe. Scientists have known for decades that prolonged and excessive exposure to crystalline silica dust in mining environments can cause silicosis, a noncancerous lung disease. During the 1980's, studies were conducted that suggested that crystalline silica also was a carcinogen. As a result of these findings, crystalline silica has been regulated under the Occupational Safety and Health Administration's (OSHA) Hazard Communication Standard (HCS). Under HCS, OSHAregulated businesses that use materials containing 0.1% or more crystalline silica must follow Federal guidelines concerning hazard communication and worker training. Although the HCS does not require that samples be analyzed for crystalline silica, mineral suppliers or OSHAregulated

  12. Silica from Ash

    Indian Academy of Sciences (India)

    Silica (SiOz) is one of the valuable inorganic multipurpose chemical compounds. It can exist in gel, crystalline and amorphous forms. It is the most abundant material on the earth's crust. However, manufacture of pure silica is energy intensive. A variety of industrial processes, involving conven- tional raw materials require ...

  13. An Overview of Polish Martial Arts

    Directory of Open Access Journals (Sweden)

    Wojciech J. Cynarski

    2012-07-01

    Full Text Available The purpose of this study is to explain the revival of Polish martial arts from the perspectives of cultural sociology, the sciences of physical culture, and the humanistic theory of martial arts. The Polish Martial Arts (Polskie Sztuki Walki are a subject still requiring serious scientific examination, even in Poland. There are few works concerning the history of Polish weapons, and most only describe techniques for wielding specific types of edged weapons. Nevertheless, there is a large group of enthusiasts trying to restore and cultivate the old Polish tradition, a tradition with heavy emphasis on the art of fencing. The author knows many of the people and facts presented here, from personal observation and from direct participation in these arts. As a disciple of the late Master Yoshio Sugino (10th-dan Kobudo Katori Shinto-ryu, he fought against the Polish saber champion, and he has taken part in joint exhibitions of Polish and Japanese fencing.

  14. Preparation and evaluation of zirconia-coated silica monolith for capillary electrochromatography.

    Science.gov (United States)

    Shi, Z-G; Feng, Y-Q; Xu, L; Zhang, M; Da, S-L

    2004-06-17

    Silica monoliths were fabricated inside fused-silica capillaries. Then the monolithic columns were coated with membrane-like zirconia. The zirconia-coated silica monoliths exhibited different EOF behavior comparing with that of bare silica monoliths. The magnitude and direction could be manipulated by changing the running buffers. Due to the amphoteric characteristic of zirconia, the silica monoliths with zirconia surface facilitate the separation of basic compounds. Aromatic amines and alkaloids were separated without obvious peak tailing. The zirconia surface was easily modified with octadecylphosphonic acid for the separation of neutral compounds. Column efficiency as high as 90,000 and 80,000m(-1) was obtained for beberine and naphthalene, respectively. Furthermore, the zirconia coating increased the stability of the monolithic columns. Even after being exposed to severe condition, there was no apparently efficiency decrease for the test samples.

  15. The tourism attractiveness of Polish libraries

    OpenAIRE

    Miedzińska, Magdalena; Tanaś, Sławoj

    2009-01-01

    The aim of the article is to draw the reader's attention to the tourism attractiveness of renowned Polish libraries. These have attained a tourism function due to tourism exploration and penetration, but remain in the shadow of other Polish cultural assets. The article outlines the historical geography of Polish libraries, an analysis of tourism assets and an attempt to classify and catalogue libraries in Poland.

  16. Chemical mechanical polishing of tantalum and tantalum nitride

    Science.gov (United States)

    Janjam, Sathish Babu S. V.

    There is a continuing need in the semiconductor industry to clear residual copper (Cu) and planarize the tantalum (Ta)/tantalum nitride (TaN) barrier/etch stop layer with a higher removal rate using the technique of Chemical Mechanical Polishing (CMP). Obtaining high removal rates for Ta/TaN is very challenging as the films are very hard, and hence it is difficult to achieve high Ta/TaN removal rates by just relying on an increase in the mechanical forces (operating pressure) alone during CMP. Ta/TaN is an inert metal, therefore, obtaining high Ta/TaN removal rates by using chemical additives is also challenging. Not only Ta/TaN needs to be removed at a higher rate in the second step of polishing, but also remaining Cu should be cleared. It is important to search for novel chemicals that can form a thin film on the Ta/TaN surface which can be easily abraded by the polishing pad with very less pressure. In this work, oxalic and tartaric acids have been investigated as the complexing agents in slurries for Ta/TaN CMP. Oxalic and tartaric acids appear to be reactive with Ta in the presence of hydrogen peroxide. A dispersion of the Oxalic acid (OA)/Tartaric Acid (TA) - peroxide mixtures with silica (fumed/colloidal) can be used to achieve Ta removal rates that are ˜ 90 nm/min at pH between 3 to 6 by applying a down force of 6.3 psi, where as at a lower down force of 2 psi, a removal rate of ˜ 40 nm/min has been achieved at pH = 3. It was shown earlier that a high Cu removal rate can be obtained using OA-peroxide based slurries with/without the addition of abrasives at pH = 3 [1]. So, in the first step, Cu could be removed at high rates at pH = 3 and by changing the pH to 5 or 6, Ta/TaN can be removed as mentioned above. Hence these slurries could be used as "single dispersion slurries " that could be used for both the first and second steps of Cu CMP. During the second step (barrier layer polish), Cu removal rates are low but not low enough to minimize dishing with

  17. Fuse Modeling for Reliability Study of Power Electronic Circuits

    DEFF Research Database (Denmark)

    Bahman, Amir Sajjad; Iannuzzo, Francesco; Blaabjerg, Frede

    2017-01-01

    This paper describes a comprehensive modeling approach on reliability of fuses used in power electronic circuits. When fuses are subjected to current pulses, cyclic temperature stress is introduced to the fuse element and will wear out the component. Furthermore, the fuse may be used in a large v...

  18. Perceptions of and Attitudes towards Regional Varieties of Polish: Views from Two Polish Provinces

    Science.gov (United States)

    Milobog, Magdalena; Garrett, Peter

    2011-01-01

    This paper reports a study of perceptions and attitudes relating to regional varieties of Polish. The methodology followed folk linguistic approaches to attitudes research. Respondents in two Polish provinces were asked to draw on a map of Poland where they thought the main regional varieties of Polish were spoken, and then to name and…

  19. Polish Decadence: Leopold Staff's Igrzysko in the European Context

    Directory of Open Access Journals (Sweden)

    Julia Przybos

    2012-03-01

    expression. It is my hypothesis that taken out of its secular context, religious revisionism of the kind practiced by French decadents may be seen as shocking transgression in a fiercely catholic country like Poland. In the country that lost its independence in 1794 and was ever since seeking to regain it, Catholic Church was perceived as an essential ally in the struggle against main occupying powers: Orthodox Russia, and Protestant Prussia. In the course of the 19th century Catholicism and patriotism had been effectively fused in Polish national conscience. In this charged political context a Polish author revisiting Church dogma or tradition was at risk of being perceived not only as a religious outcast but also as a traitor to the cause of Polish independence. To test my hypothesis I propose to examine Igrzysko (Game, a forgotten play by Leopold Staff. Admired today chiefly as a poet, the young Staff wrote Igrzysko in Poland after a long sojourn in Paris where he had lived among the international crowd of fin de siècle writers and artists. The play was first produced in Lemberg in 1909 and after a few performances vanished forever from Polish theatrical repertoire. Leopold Staff's play is set in ancient Rome and depicts tribulations of an actor who, while impersonating a Christian awaiting crucifixion, converts to Christianity. In his play, Staff revives the legend of Saint Genesius, an actor in Arles who died a martyr's death in 286 under Diocletian. In Spain, Saint Genesius's legend inspired Lope de Vega who wrote Acting is Believing (Lo fingido verdadero, 1607. In France, it was the source for Jean Rotrou's Saint Genest (1646. All told, the legend of Genesius is a popular theme for artists who wish to explore the distinction between art and life. An important addition to this old tradition, Staff's play contains, however, a decadent and potentially scandalous twist. Unlike in Acting is Believing and Saint Genest, the protagonist's conversion is very short

  20. History of Polish gastrointestinal radiology.

    Science.gov (United States)

    Urbanik, A

    2003-12-01

    As early as several days after the publication of the information concerning Roentgen's discovery the first radiological examinations were performed in Poland. The new method was immediately introduced into medical practice, including gastroenterology. In that pioneer period the most important works were those by Walery Jaworski who was the first man in the world to perform an X-ray of gall stones as well as the stomach with the use of a contrast medium. In its more-than-a-hundred-year history Polish gastrointestinal radiology has attempted not only to catch up with the world science, but it also has made a considerable contribution to its development.

  1. Corporate Politics on Polish Millennials

    OpenAIRE

    Natalia Roślik

    2017-01-01

    In the very beginning of this particular paper, an author is trying to determine and describe who Millennials actually are. Then, the basis of Millennials definition is analysing corporation’s activity over the past years regarding this age group. The main goal of the thesis is to bring their specific futures out and describe what corporations on Polish job market are doing to encourage them to work in their offices. Especially in Poland within the last years, it is observed that big multinat...

  2. Polish Foundation for Energy Efficiency

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-12-31

    The Polish Foundation for Energy Efficiency (FEWE) was established in Poland at the end of 1990. FEWE, as an independent and non-profit organization, has the following objectives: to strive towards an energy efficient national economy, and to show the way and methods by use of which energy efficiency can be increased. The activity of the Foundation covers the entire territory of Poland through three regional centers: in Warsaw, Katowice and Cracow. FEWE employs well-known and experienced specialists within thermal and power engineering, civil engineering, economy and applied sciences. The organizer of the Foundation has been Battelle Memorial Institute - Pacific Northwest Laboratories from the USA.

  3. Endodontic and post-endodontic management of a fused molar

    Directory of Open Access Journals (Sweden)

    Ruchi Gupta

    2013-01-01

    Full Text Available Treatment of fused teeth needs special care and attention to the bizarre anatomy. This paper describes root canal treatment of a fused carious tooth presenting with apical periodontitis. It is a rare case of fusion of the mandibular second molar with a paramolar. There is no literature regarding placement of crown over endodontically treated fused teeth. In this case, the fused teeth were endodontically treated and restored by a porcelain fused to metal crown.

  4. Endodontic and post-endodontic management of a fused molar.

    Science.gov (United States)

    Gupta, Ruchi; Prakash, Vijay; Sharma, Mohit

    2013-01-01

    Treatment of fused teeth needs special care and attention to the bizarre anatomy. This paper describes root canal treatment of a fused carious tooth presenting with apical periodontitis. It is a rare case of fusion of the mandibular second molar with a paramolar. There is no literature regarding placement of crown over endodontically treated fused teeth. In this case, the fused teeth were endodontically treated and restored by a porcelain fused to metal crown.

  5. Sexual activity of Polish adults.

    Science.gov (United States)

    Pastwa-Wojciechowska, Beata; Izdebski, Zbigniew

    2014-01-01

    The purpose of this research was to explore the subject of sexual activity in the Polish population, with special focus on age and gender differences, and sexual infidelity. Sexual activity is one of the basic factors in initiating and maintaining relationships. On the one hand, sexual activity enables us to meet natural needs and maintain an intimate relationship with another human being; on the other, it may allow us to overcome loneliness and social isolation by providing the opportunity to express feelings of closeness and unity. The research was conducted on a representative group of 3,200 Poles aged between 15-49, with the support of a well-known Polish research company - TNS OBOP. Face-to-face and Pencil and Paper (PAPI) interviews were carried out. The results focus on two main issues: the age and motives of sexual initiation among teenagers (with a significant percentage starting their sexual activity at the age of 15), and the quality of the sexual lives of adults (average number of sexual partners, sexual infidelity and sexual satisfaction). There is dependence between the type of relationship and the performance or non-performance of sexual activity, as well as the quality of the relationship. Among both adolescents and adults, remaining in a stable relationship (partnership or marriage) promotes loyalty. The performance of sexual goals turns out to be an important mechanism regulating the interpersonal aspects of a relationship, influencing their perception and evaluation.

  6. Sexual activity of Polish adults

    Directory of Open Access Journals (Sweden)

    Beata Pastwa-Wojciechowska

    2014-03-01

    Full Text Available Aim. The purpose of this research was to explore the subject of sexual activity in the Polish population, with special focus on age and gender differences, and sexual infidelity. Sexual activity is one of the basic factors in initiating and maintaining relationships. On the one hand, sexual activity enables us to meet natural needs and maintain an intimate relationship with another human being; on the other, it may allow us to overcome loneliness and social isolation by providing the opportunity to express feelings of closeness and unity. Material and method. The research was conducted on a representative group of 3,200 Poles aged between 15–49, with the support of a well-known Polish research company – TNS OBOP. Face-to-face and Pencil and Paper (PAPI interviews were carried out. Results. The results focus on two main issues: the age and motives of sexual initiation among teenagers (with a significant percentage starting their sexual activity at the age of 15, and the quality of the sexual lives of adults (average number of sexual partners, sexual infidelity and sexual satisfaction. Conclusion. There is dependence between the type of relationship and the performance or non-performance of sexual activity, as well as the quality of the relationship. Among both adolescents and adults, remaining in a stable relationship (partnership or marriage promotes loyalty. The performance of sexual goals turns out to be an important mechanism regulating the interpersonal aspects of a relationship, influencing their perception and evaluation.

  7. Buffered Electrochemical Polishing of Niobium

    Energy Technology Data Exchange (ETDEWEB)

    Ciovati, Gianluigi [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Tian, Hui [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); College of William and Mary, Williamsburg, VA (United States); Corcoran, Sean [Virginia Polytechnic Inst. and State Univ. (Virginia Tech), Blacksburg, VA (United States)

    2011-03-01

    The standard preparation of superconducting radio-frequency (SRF) cavities made of pure niobium include the removal of a 'damaged' surface layer, by buffered chemical polishing (BCP) or electropolishing (EP), after the cavities are formed. The performance of the cavities is characterized by a sharp degradation of the quality factor when the surface magnetic field exceeds about 90 mT, a phenomenon referred to as 'Q-drop.' In cavities made of polycrystalline fine grain (ASTM 5) niobium, the Q-drop can be significantly reduced by a low-temperature (? 120 °C) 'in-situ' baking of the cavity if the chemical treatment was EP rather than BCP. As part of the effort to understand this phenomenon, we investigated the effect of introducing a polarization potential during buffered chemical polishing, creating a process which is between the standard BCP and EP. While preliminary results on the application of this process to Nb cavities have been previously reported, in this contribution we focus on the characterization of this novel electrochemical process by measuring polarization curves, etching rates, surface finish, electrochemical impedance and the effects of temperature and electrolyte composition. In particular, it is shown that the anodic potential of Nb during BCP reduces the etching rate and improves the surface finish.

  8. Method of polishing nickel-base alloys and stainless steels

    Science.gov (United States)

    Steeves, Arthur F.; Buono, Donald P.

    1981-01-01

    A chemical attack polish and polishing procedure for use on metal surfaces such as nickel base alloys and stainless steels. The chemical attack polish comprises Fe(NO.sub.3).sub.3, concentrated CH.sub.3 COOH, concentrated H.sub.2 SO.sub.4 and H.sub.2 O. The polishing procedure includes saturating a polishing cloth with the chemical attack polish and submicron abrasive particles and buffing the metal surface.

  9. Advanced techniques for computer-controlled polishing

    Science.gov (United States)

    Schinhaerl, Markus; Stamp, Richard; Pitschke, Elmar; Rascher, Rolf; Smith, Lyndon; Smith, Gordon; Geiss, Andreas; Sperber, Peter

    2008-08-01

    Computer-controlled polishing has introduced determinism into the finishing of high-quality surfaces, for example those used as optical interfaces. Computer-controlled polishing may overcome many of the disadvantages of traditional polishing techniques. The polishing procedure is computed in terms of the surface error-profile and the material removal characteristic of the polishing tool, the influence function. Determinism and predictability not only enable more economical manufacture but also facilitate considerably increased processing accuracy. However, there are several disadvantages that serve to limit the capabilities of computer-controlled polishing, many of these are considered to be issues associated with determination of the influence function. Magnetorheological finishing has been investigated and various new techniques and approaches that dramatically enhance the potential as well as the economics of computer-controlled polishing have been developed and verified experimentally. Recent developments and advancements in computer-controlled polishing are discussed. The generic results of this research may be used in a wide variety of alternative applications in which controlled material removal is employed to achieve a desired surface specification, ranging from surface treatment processes in technical disciplines, to manipulation of biological surface textures in medical technologies.

  10. Polish Industry and Art at CERN

    CERN Multimedia

    2000-01-01

    On 17 October 2000 the second Polish industrial and technological exhibition opened at CERN. The first one was held five years ago and nine of the companies that were present then have come back again this year. Six of those companies were awarded contracts with CERN in 1995. Three Polish officials were present at the Opening Ceremony today: Mrs Malgorzata Kozlowska, Under-secretary of State in the State Committee for Scientific Research, Mr Henryk Ogryczak, Under-secretary of State in Ministry of Economy and Prof. Jerzy Niewodniczanski, President of National Atomic Energy Agency. Professor Luciano Maiani welcomed the Polish delegation to CERN and stressed the important contribution of Polish scientists and industrialists to the work of the laboratory. Director General Luciano Maiani (back left) and head of SPL division Karl-Heinz Kissler (back right) visit the Poland at CERN exhibition… The exhibition offers Polish companies the opportunity to establish professional contacts with CERN. Nineteen companies...

  11. Silica aerogel Cerenkov counter

    International Nuclear Information System (INIS)

    Yasumi, S.; Masaike, A.; Yamamoto, A.; Yoshimura, Y.; Kawai, H.

    1984-03-01

    In order to obtain silica aerogel radiators of good quality, the prescription used by Saclay group has been developed. We have done several experiments using beams from KEK.PS to test the performance of a Cerenkov counter with aerogel modules produced in KEK. It turned out that these modules had excellent quality. The production rate of silica aerogel in KEK is 15 -- 20 litres a week. Silica aerogel modules of 20 x 10 x 3 cm 3 having the refractive index of 1.058 are successfully being used by Kyoto University group in the KEK experiment E92 (Σ). Methodes to produce silica aerogel with higher refractive index than 1.06 has been investigated both by heating an module with the refractive index of 1.06 and by hydrolyzing tetraethyl silicate. (author)

  12. Cellulose-silica aerogels.

    Science.gov (United States)

    Demilecamps, Arnaud; Beauger, Christian; Hildenbrand, Claudia; Rigacci, Arnaud; Budtova, Tatiana

    2015-05-20

    Aerogels based on interpenetrated cellulose-silica networks were prepared and characterised. Wet coagulated cellulose was impregnated with silica phase, polyethoxydisiloxane, using two methods: (i) molecular diffusion and (ii) forced flow induced by pressure difference. The latter allowed an enormous decrease in the impregnation times, by almost three orders of magnitude, for a sample with the same geometry. In both cases, nanostructured silica gel was in situ formed inside cellulose matrix. Nitrogen adsorption analysis revealed an almost threefold increase in pores specific surface area, from cellulose aerogel alone to organic-inorganic composite. Morphology, thermal conductivity and mechanical properties under uniaxial compression were investigated. Thermal conductivity of composite aerogels was lower than that of cellulose aerogel due to the formation of superinsulating mesoporous silica inside cellulose pores. Furthermore, composite aerogels were stiffer than each of reference aerogels. Copyright © 2015 Elsevier Ltd. All rights reserved.

  13. Electrochemical Sensors: Functionalized Silica

    Energy Technology Data Exchange (ETDEWEB)

    Fryxell, Glen E.; Lin, Yuehe; Yantasee, Wassana

    2009-03-24

    This chapter summarizes recent devellopment of electrochemical sensors based on functionlized mesoporous silica materials. The nanomatrials based sensors have been developed for sensitive and selective enrironmental detection of toxic heavy metal and uranium ions.

  14. All-silica nanofluidic devices for DNA-analysis fabricated by imprint of sol-gel silica with silicon stamp

    DEFF Research Database (Denmark)

    Mikkelsen, Morten Bo Lindholm; Letailleur, Alban A; Søndergård, Elin

    2011-01-01

    We present a simple and cheap method for fabrication of silica nanofluidic devices for single-molecule studies. By imprinting sol-gel materials with a multi-level stamp comprising micro- and nanofeatures, channels of different depth are produced in a single process step. Calcination of the imprin......We present a simple and cheap method for fabrication of silica nanofluidic devices for single-molecule studies. By imprinting sol-gel materials with a multi-level stamp comprising micro- and nanofeatures, channels of different depth are produced in a single process step. Calcination...... of the imprinted hybrid sol-gel material produces purely inorganic silica, which has very low autofluorescence and can be fusion bonded to a glass lid. Compared to top-down processing of fused silica or silicon substrates, imprint of sol-gel silica enables fabrication of high-quality nanofluidic devices without...... expensive high-vacuum lithography and etching techniques. The applicability of the fabricated device for single-molecule studies is demonstrated by measuring the extension of DNA molecules of different lengths confined in the nanochannels....

  15. 30 CFR 56.6502 - Safety fuse.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Safety fuse. 56.6502 Section 56.6502 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Explosives Nonelectric Blasting § 56...

  16. 30 CFR 57.6502 - Safety fuse.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Safety fuse. 57.6502 Section 57.6502 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-UNDERGROUND METAL AND NONMETAL MINES Explosives Nonelectric Blasting...

  17. Fungal Systematics and Evolution: FUSE 1

    NARCIS (Netherlands)

    Crous, Pedro W; Schumacher, René K; Wingfield, Michael J; Lombard, Lorenzo; Giraldo, Alejandra; Christensen, Martha; Gardiennet, Alain; Nakashima, Chiharu; Pereira, Olinto L; Smith, Alexander J; Groenewald, Johannes Z

    2015-01-01

    Fungal Systematics and Evolution (FUSE) is introduced as a new series to expedite the publication of issues relating to the epitypification of formerly described species, report new sexual-asexual connections, the merging of sexual and asexual gen¬era following the end of dual nomenclature, and to

  18. Renovating a Fusee Ceramique Barrel Vault

    NARCIS (Netherlands)

    Kamerling, M.W.

    2015-01-01

    This paper describes a proposal to renovate a Fusee Ceramique Barrel Vault with steel diagonals In 1956 two workshops, varying in height and span, were built in Wormerveer, The Netherlands. Both workshops were roofed with a concrete barrel vault with a thickness of 110 mm. The cylindrical vaults

  19. Fused aromatic thienopyrazines: structure, properties and function

    KAUST Repository

    Mondal, Rajib

    2010-01-01

    Recent development of a fused aromatic thieno[3.4-b]pyrazine system and their application in optoelectronic devices are reviewed. Introduction of a fused aromatic unit followed by side chain engineering, dramatically enhanced the charge carrier mobility in thin film transistor devices and mobilities up to 0.2 cm2/Vs were achieved. The optoelectronic properties of these fused aromatic thienopyrazine polymers (Eg = 1.3 to 1.6 eV, HOMO = -4.9 to -5.2 V) were tuned by introduction of various fused aromatic rings within thienopyrazine. By balancing the fundamental properties of these polymers, both high charge carrier mobilities and moderate PCEs in solar cells were achieved. Further, effects of copolymerizing units are discussed. Low band gap semiconducting polymer (Eg ∼ 1 eV) with high field effect mobility (0.044 cm2/Vs) was obtained using cyclopentadithiophene as copolymerizing unit. Finally, a molecular design approach to enhance the absorption coefficients is discussed, which resulted in improved power conversion efficiency in bulk heterojunction solar cells. © 2010 The Royal Society of Chemistry.

  20. Corporate Politics on Polish Millennials

    Directory of Open Access Journals (Sweden)

    Natalia Roślik

    2017-12-01

    Full Text Available In the very beginning of this particular paper, an author is trying to determine and describe who Millennials actually are. Then, the basis of Millennials definition is analysing corporation’s activity over the past years regarding this age group. The main goal of the thesis is to bring their specific futures out and describe what corporations on Polish job market are doing to encourage them to work in their offices. Especially in Poland within the last years, it is observed that big multinational companies are paying special attention to Millennials and trying to hire them before competitors will do so. As a part of this paper, an author will describe corporate politics and practices on Thomson Reuters and BNY Mellon examples. Within this work, an author is also discussing key features and differences between this generation and Millennials parent’s generation. Additionally, there is a reference to corporate social responsibility concept and work-life balance issues.

  1. Smoking characteristics of Polish immigrants in Dublin

    Directory of Open Access Journals (Sweden)

    Zatonski Witold

    2008-12-01

    Full Text Available Abstract Background This study examined two main hypotheses: a Polish immigrants' smoking estimates are greater than their Irish counterparts (b Polish immigrants purchasing cigarettes from Poland smoke "heavier" (≥ 20 cigarettes a day when compared to those purchasing cigarettes from Ireland. The study also set out to identify significant predictors of 'current' smoking (some days and everyday among the Polish immigrants. Methods Dublin residents of Polish origin (n = 1,545 completed a previously validated Polish questionnaire in response to an advertisement in a local Polish lifestyle magazine over 5 weekends (July–August, 2007. The Office of Tobacco Control telephone-based monthly survey data were analyzed for the Irish population in Dublin for the same period (n = 484. Results Age-sex adjusted smoking estimates were: 47.6% (95% Confidence Interval [CI]: 47.3%; 48.0% among the Poles and 27.8% (95% CI: 27.2%; 28.4% among the general Irish population (p 24 months were significant predictors of current smoking among the Poles. An objective validation of the self-reported smoking history of a randomly selected sub-sample immigrant group, using expired carbon monoxide (CO measurements, showed a highly significant correlation coefficient (r = 0.64 of expired CO levels with the reported number of cigarettes consumed (p Conclusion Polish immigrants' smoking estimates are higher than their Irish counterparts, and particularly if employed, with only primary-level education, and are overseas >2 years.

  2. Dihydropyridine-fused and pyridine-fused coumarins: Reduction on a glassy carbon electrode in dimethylformamide

    International Nuclear Information System (INIS)

    Nuñez-Vergara, Luis J.; Pardo-Jiménez, V.; Barrientos, C.; Olea-Azar, C.A.; Navarrete-Encina, P.A.; Squella, J.A.

    2012-01-01

    In this study, two series of dihydropyridine-fused and pyridine-fused coumarins were synthesised and electrochemically characterised in aprotic medium. In both series, the most easily reducible groups were the endocyclic carbonyl groups. The electrochemical mechanism for both types of compounds is strongly dependent on the experimental time-scale. Cyclic voltammetric (CV) reduction on a glassy carbon electrode (GCE) of the endocyclic carbonyl group of dihydropyridine-fused coumarins involves an ECEC mechanism with two electron transfer steps that are coupled with chemical reactions to produce the corresponding hemiacetal derivative. In the case of pyridine-fused coumarins, CV reduction of the endocyclic carbonyl group involves an EEC mechanism. ESR studies revealed the presence of a stabilised intermediate only for the pyridine-fused derivatives. Our theoretical study showed a spin density map of radical species delocalised mainly within the coumarin ring, indicating the reduction of the endocyclic carbonyl group. In the case of the dihydropyridine-fused derivatives, the mildly acid hydrogen of the dihydropyridine ring destabilises the radical via a father–son type reaction.

  3. Kinetics of silica polymerization

    Energy Technology Data Exchange (ETDEWEB)

    Weres, O.; Yee, A.; Tsao, L.

    1980-05-01

    The polymerization of silicic acid in geothermal brine-like aqueous solutions to produce amorphous silica in colloidal form has been studied experimentally and theoretically. A large amount of high quality experimental data has been generated over the temperature rang 23 to 100{sup 0}C. Wide ranges of dissolved silica concentration, pH, and sodium chloride concentration were covered. The catalytic effects of fluoride and the reaction inhibiting effects of aluminum and boron were studied also. Two basic processes have been separately studied: the formation of new colloidal particles by the homogeneous nucleation process and the deposition of dissolved silica on pre-existing colloidal particles. A rigorous theory of the formation of colloidal particles of amorphous silica by homogeneous nucleation was developed. This theory employs the Lothe-Pound formalism, and is embodied in the computer code SILNUC which quantitatively models the homogeneous nucleation and growth of colloidal silica particles in more than enough detail for practical application. The theory and code were extensively used in planning the experimental work and analyzing the data produced. The code is now complete and running in its final form. It is capable of reproducing most of the experimental results to within experimental error. It is also capable of extrapolation to experimentally inaccessible conditions, i.e., high temperatures, rapidly varying temperature and pH, etc.

  4. Super-polishing of Zerodur aspheres by means of conventional polishing technology

    Science.gov (United States)

    Polak, Jaroslav; Klepetková, Eva; Pošmourný, Josef; Šulc, Miroslav; Procháska, František; Tomka, David; Matoušek, Ondřej; Poláková, Ivana; Šubert, Eduard

    2015-01-01

    This paper describes a quest to find simple technique to superpolish Zerodur asphere (55μm departure from best fit sphere) that could be employed on old fashion way 1-excenter optical polishing machine. The work focuses on selection of polishing technology, study of different polishing slurries and optimization of polishing setup. It is demonstrated that either by use of fine colloidal CeO2 slurry or by use of bowl-feed polishing setup with CeO2 charged pitch we could reach 0.4nm RMS roughness while removing <30nm of surface layer. This technique, although not optimized, was successfully used to improve surface roughness on already prepolished Zerodur aspheres without necessity to involve sophisticated super-polishing technology and highly trained manpower.

  5. Comparative study of performance of shoe polishes formulated from ...

    African Journals Online (AJOL)

    GARZALI

    This should make the polish remains as discrete solid particles held mechanically within the leather. This work intends to explore the use of polyethylene pigment in the production of shoe polish. The shoe polish produced will be applied alongside shoe polish from carbon black (CI black Pigment 7) on finished black leather ...

  6. Silica coated ionic liquid templated mesoporous silica nanoparticles ...

    African Journals Online (AJOL)

    Silica coated ionic liquid templated mesoporous silica nanoparticles. E.D.M. Isa, M. B. A. Rahman, H. Ahmad. Abstract. A series of long chain pyridinium based ionic liquids 1-tetradecylpyridinium bromide, 1-hexadecylpyridinium bromide and 1-1-octadecylpyridinium bromide were used as templates to prepare silica coated ...

  7. New Environmental Practices in Polish Production Firms

    DEFF Research Database (Denmark)

    Kræmer, Trine Pipi

    2002-01-01

    Based on five case studies in Poland, the paper discusses, how a specific environmental policy influences the firms? industrial environmental practices. The study illustrates, how the Polish environmental policy, dominated by environmental charges on emissions, is extremely effective in improving...

  8. Electro Polishing of Niobium Cavities at DESY

    CERN Document Server

    Matheisen, A; Morales, H; Petersen, B; Schmoekel, M; Steinhau-Kühl, N

    2004-01-01

    At DESY a facility for electro polishing (EP) of the super conducting (s.c.) TESLA/TTF cavities have been built and is operational since summer 2003. The EP infrastructure is capable to handle single-cell structures and the standard TESLA/ TTF nine-cell cavities. Several electro polishing processes have been made since and acceleration voltage up to 40 MV/m have been reached in nine cell structures. We report on measurements and experiences gained since 2003 as well as on handling procedures developed for the preparation of electro polished resonators. Specific data like heat production, variation of current density and bath aging will be presented. Another important point for reproducible results is the quality control of the electro polishing process. First quality control steps to be implanted in the EP procedure for large-scale production will be described.

  9. Semiological analysis of Polish theater posters

    Directory of Open Access Journals (Sweden)

    Jelena Nikolić

    2016-02-01

    Full Text Available Through the application of semiological analysis to theater posters made by two Polish authors, the paper uncovers signs, meanings, codes and specifics of the „Polish school of poster-making“ and contemporary Polish posters. Aside from this, I suggest a methodological framework for studying the issue of coding and shaping a theater poster as a culturally specific form of visual communication. The aesthetic and semiotic outlook of the Polish theater posters which were chosen is analyzed using the semiological method which highlights their differences and similarities. By pointing out the system of codes through the examples given here, a graphic designer is informed about the existence and the possibilities of a more systematic approach to shaping a theater poster.

  10. Report on Polish Public Libraries 2001

    OpenAIRE

    Bednarek-Michalska, Bożena; Szatkowska, Olga

    2001-01-01

    Report is an overview of polish public libraries, services to a variety of communities, it also provides statistics, n explanation of the funding policy for public libraries in Poland and information about the governance of public libraries in the country.

  11. 30 CFR 57.12036 - Fuse removal or replacement.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Fuse removal or replacement. 57.12036 Section 57.12036 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND... Electricity Surface and Underground § 57.12036 Fuse removal or replacement. Fuses shall not be removed or...

  12. 30 CFR 56.12036 - Fuse removal or replacement.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Fuse removal or replacement. 56.12036 Section 56.12036 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND... § 56.12036 Fuse removal or replacement. Fuses shall not be removed or replaced by hand in an energized...

  13. Semantic image segmentation with fused CNN features

    Science.gov (United States)

    Geng, Hui-qiang; Zhang, Hua; Xue, Yan-bing; Zhou, Mian; Xu, Guang-ping; Gao, Zan

    2017-09-01

    Semantic image segmentation is a task to predict a category label for every image pixel. The key challenge of it is to design a strong feature representation. In this paper, we fuse the hierarchical convolutional neural network (CNN) features and the region-based features as the feature representation. The hierarchical features contain more global information, while the region-based features contain more local information. The combination of these two kinds of features significantly enhances the feature representation. Then the fused features are used to train a softmax classifier to produce per-pixel label assignment probability. And a fully connected conditional random field (CRF) is used as a post-processing method to improve the labeling consistency. We conduct experiments on SIFT flow dataset. The pixel accuracy and class accuracy are 84.4% and 34.86%, respectively.

  14. Electrolysis of uranium tetrafluorure fused salts

    International Nuclear Information System (INIS)

    Perillo, P.M.; Botbol, J.

    1991-01-01

    Electrolytic preparation of U has been unsuccessful because the metal formed is in easily oxidized state. Electrolytic depositions were made under various conditions from fused NaCl-KCl baths containing UF 4 . X-ray diffraction studies were made of the products. The results indicate that mixed U with several oxides phases are produced. It was concluded that the method was unlikely to be efficient for the production of U metal. (Author) [es

  15. Titanium metal obtention by fused salts electrolysis

    International Nuclear Information System (INIS)

    Perillo, P.M.; Ares, Osvaldo; Botbol, Jose.

    1989-01-01

    Potassium fluorotitanate dissolved in fused sodium chloride or potassium chloride may be electrolyzed under an inert gas atmosphere. Solid electrolysis products are formed on the cathode which contains titanium metal, sodium chloride, lower fluorotitanates and small quantities of alkali metal fluorotitanate. The extraction of titanium from the electrolysis products may be carried out by aqueous leaching (removal of chloride salts of alkali metals and a certain amount of fluorotitanates). Titanium metal obtained is relatively pure. (Author)

  16. Electrolytic polishing system for space age materials

    International Nuclear Information System (INIS)

    Coons, W.C.; Iosty, L.R.

    1976-01-01

    A simple electrolytic polishing technique was developed for preparing Cr, Co, Hf, Mo, Ni, Re, Ti, V, Zr, and their alloys for structural analysis on the optical microscope. The base electrolyte contains 5g ZnCl 2 and 15g AlCl 3 . 6H 2 O in 200 ml methyl alcohol, plus an amount of H 2 SO 4 depending on the metal being polished. Five etchants are listed

  17. Trace element analysis of nail polishes

    International Nuclear Information System (INIS)

    Misra, G.; Mittal, V.K.; Sahota, H.S.

    1999-01-01

    Instrumental neutron activation analysis (INAA) technique was used to measure the concentrations of various trace elements in nail polishes of popular Indian and foreign brands. The aim of the present experiment was to see whether trace elements could distinguish nail polishes of different Indian and foreign brands from forensic point of view. It was found that cesium can act as a marker to differentiate foreign and Indian brands. (author)

  18. Interlocking directorships in Polish joint stock companies:

    OpenAIRE

    Pawlak, Marek

    2008-01-01

    Studies concerning interlocking directorships have been carried out among Polish joint stock corporations. The main source of data have been the announcements that are to be published by corporations regularly in a journal called Business and Court Gazette (BCG). Interlocking directorships constitute a network among corporations the use of which enables co-ordinated management of the whole group. The phenomenon of interlocking directorships in Polish joint stock companies can be compared to t...

  19. Jewish problem in the Polish Communist Party

    Directory of Open Access Journals (Sweden)

    Cimek Henryk

    2016-12-01

    Full Text Available Jews accounted for approx. 8-10% of the population of the Second Republic and in the communist movement (Polish Communist Party and Polish Communist Youth Union the rate was approx, 30%, while in subsequent years it much fluctuated. The percentage of Jews was the highest in the authorities of the party and in the KZMP. This had a negative impact on the position of the KPP on many issues, especially in its relation to the Second Republic.

  20. Attack polish for nickel-base alloys and stainless steels

    Science.gov (United States)

    Not Available

    1980-05-28

    A chemical attack polish and polishing procedure for use on metal surfaces such as nickel base alloys and stainless steels is described. The chemical attack polich comprises FeNO/sub 3/, concentrated CH/sub 3/COOH, concentrated H/sub 2/SO/sub 4/ and H/sub 2/O. The polishing procedure includes saturating a polishing cloth with the chemical attack polish and submicron abrasive particles and buffing the metal surface.

  1. Experimental Polish-Lithuanian Corpus with the Semantic Annotation Elements

    Directory of Open Access Journals (Sweden)

    Danuta Roszko

    2015-06-01

    Full Text Available Experimental Polish-Lithuanian Corpus with the Semantic Annotation Elements In the article the authors present the experimental Polish-Lithuanian corpus (ECorpPL-LT formed for the idea of Polish-Lithuanian theoretical contrastive studies, a Polish-Lithuanian electronic dictionary, and as help for a sworn translator. The semantic annotation being brought into ECorpPL-LT is extremely useful in Polish-Lithuanian contrastive studies, and also proves helpful in translation work.

  2. Conformal polishing approach: Tool footprint analysis

    Directory of Open Access Journals (Sweden)

    José A Dieste

    2016-02-01

    Full Text Available Polishing process is one of the most critical manufacturing processes during a metal part production because it determines the final quality of the product. Free-form surface polishing is a handmade process with lots of rejected parts, scrap generation and time and energy consumption. Two different research lines are being developed: prediction models of the final surface quality parameters and an analysis of the amount of material removed depending on the polishing parameters to predict the tool footprint during the polishing task. This research lays the foundations for a future automatic conformal polishing system. It is based on rotational and translational tool with dry abrasive in the front mounted at the end of a robot. A tool to part concept is used, useful for large or heavy workpieces. Results are applied on different curved parts typically used in tooling industry, aeronautics or automotive. A mathematical model has been developed to predict the amount of material removed in function of polishing parameters. Model has been fitted for different abrasives and raw materials. Results have shown deviations under 20% that implies a reliable and controllable process. Smaller amount of material can be removed in controlled areas of a three-dimensional workpiece.

  3. Laser polishing of additive manufactured Ti alloys

    Science.gov (United States)

    Ma, C. P.; Guan, Y. C.; Zhou, W.

    2017-06-01

    Laser-based additive manufacturing has attracted much attention as a promising 3D printing method for metallic components in recent years. However, surface roughness of additive manufactured components has been considered as a challenge to achieve high performance. In this work, we demonstrate the capability of fiber laser in polishing rough surface of additive manufactured Ti-based alloys as Ti-6Al-4V and TC11. Both as-received surface and laser-polished surfaces as well as cross-section subsurfaces were analyzed carefully by White-Light Interference, Confocal Microscope, Focus Ion Beam, Scanning Electron Microscopy, Energy Dispersive Spectrometer, and X-ray Diffraction. Results revealed that as-received Ti-based alloys with surface roughness more than 5 μm could be reduce to less than 1 μm through laser polishing process. Moreover, microstructure, microhardness and wear resistance of laser-polished zone was investigated in order to examine the thermal effect of laser polishing processing on the substrate of additive manufactured Ti alloys. This proof-of-concept process has the potential to effectively improve the surface roughness of additive manufactured metallic alloy by local polishing method without damage to the substrate.

  4. Interculutral Polish-Chinese QQing

    Directory of Open Access Journals (Sweden)

    Elżbieta Gajek

    2012-12-01

    Full Text Available Working in tandem with the use of information and communication technologies is well-known and frequently used as a method of supporting learning of foreign languages in authentic communication. It is based on a constructivist approach to teaching. In the reported case study Polish and Chinese students discussed in English preprepared topics. The work shows the potential of e-learning at the micro level, as the language and intercultural task is implemented into an academic course without modification of the objectives and learning outcomes of the course. Evaluation carried out at the end of the project indicates that both groups perceived the task as a significant linguistic, cultural and personal experience. They stressed the importance of sharing “culture for culture” as the partner culture was new for most of them. The ability to talk and respond to information which was often strange, from the point of view of their own culture, allowed for learning intercultural competence ̔in action’.

  5. Silica reinforced triblock copolymer gels

    DEFF Research Database (Denmark)

    Theunissen, E.; Overbergh, N.; Reynaers, H.

    2004-01-01

    The effect of silica and polymer coated silica particles as reinforcing agents on the structural and mechanical properties of polystyrene-poly(ethylene/butylene)-polystyrene (PS-PEB-PS) triblock gel has been investigated. Different types of chemically modified silica have been compared in order...

  6. Surface forces between hydrophilic silica surfaces in a moisture-sensitive oleophilic diacrylate monomer liquid

    Science.gov (United States)

    Ito, Shunya; Kasuya, Motohiro; Kurihara, Kazue; Nakagawa, Masaru

    2018-02-01

    We measured the surface forces generated between fused silica surfaces in a low-viscosity oleophilic diacrylate monomer for reliably repeated ultraviolet (UV) nanoimprinting, and studied the influence of water in monomer liquids on the forces. Fused silica surfaces, with a static contact angle of 52.6 ± 1.7° for water, owing to the low degree of hydroxylation, hardly showed reproducible surface forces with repeated scan cycles, comprising approach and separation, even in an identical liquid monomer medium with both of low and high water content. The monomer liquid with a high water content of approximately 420 ppm showed a greater tendency to increase the surface forces at longer surface-surface distances compared with the monomer liquid with a low water content of approximately 60 ppm. On the other hand, silica surfaces with a water contact angle of < 5° after exposure to vacuum UV (VUV) light under a reduced air pressure showed reproducible profiles of surfaces forces using the monomer with a low water concentration of approximately 60 ppm for repeated surface forces scan cycles even in separately prepared silica surfaces, whilst they showed less reproducible profiles in the liquids with high water content of 430 ppm. These results suggested that water possibly adsorbed on the hydrophilic and hydrophobic silica surfaces in the monomer liquid of the high water concentration influenced the repeatability of the surface forces profiles.

  7. Channel waveguides formed by ion implantation of PECVD grown silica

    International Nuclear Information System (INIS)

    Leech, P.W.; Faith, M.F.; Johnson, C.M.; Ridgway, M.C.; Bazylenko, M.

    1997-01-01

    Low loss channel waveguides have been formed in silica-on-silicon by implantation with 5 MeV Si and Ge ions. In these experiments, the substrate was comprised of an undoped layer of silica (30 μm thick) which was grown by plasma enhanced chemical vapour deposition (PECVD). The optical loss characteristics of the waveguides, as measured at both λ 1300 and 1550 nm, were independent of the implanted ion species. A minimum in the attenuation loss (α) of ∼0.10-0.20 dB/cm was obtained following both a pre-implant (1050 o C) and a post-implant (400-500 o C) anneal of the waveguides. The ability to produce a minimum in α by pre-implant annealing has been attributed to the thermally induced relaxation of the densified structure in the as-grown layer. Only a comparatively small degree of compaction was measured for Si-implanted samples which did not receive a pre-implant anneal. In contrast, the much larger degree of compaction in the pre-implant annealed samples was similar in magnitiude to that observed in fused silica. These are the first reported examples of ion-implanted waveguides using a substrate of silica grown by PECVD. (author)

  8. Modelling and Analysis of Proximity Effect in IGBT Fuses

    DEFF Research Database (Denmark)

    Iov, Florin; Blaabjerg, Frede; Rasmussen, Henrik

    2005-01-01

    . Even with an active protection, a high power IGBT still has a risk of exhibiting a violent rupture in the case of a fault if e.g. IGBT fuses are not protecting it. By introducing fuses into voltage source converters a better protection of IGBT's can be achieved. However, skin and proximity effects...... affect the current distribution in a fuse due to the high frequency currents and thus a need for de-rating the fuse. This paper shows an analytical model for studying the proximity effect into a fuse. The results obtained using this model are compared with experiments....

  9. Outbursts In Symbiotic Binaries (FUSE 2000)

    Science.gov (United States)

    Kenyon, Scott J.; Sonneborn, George (Technical Monitor)

    2002-01-01

    During the past year, we made good progress on analysis of FUSE observations of the symbiotic binary Z And. For background, Z And is a binary system composed of a red giant and a hot component of unknown status. The orbital period is roughly 750 days. The hot component undergoes large-scale eruptions every 10-20 yr. An outburst began several years ago, triggering this FUSE opportunity. First, we obtained an excellent set of ground-based optical data in support, of the FUSE observations. We used FAST, a high throughput low resolution spectrograph on the 1.5-m telescope at Mt. Hopkins, Arizona. A 300 g/ mm grating blazed at 4750 A, a 3 in. slit, and a thinned Loral 512 x 2688 CCD gave us spectra covering 3800-7500 A at a resolution of 6 A. The wavelength solution for each spectrum has a probable error of +/- 0.5 A or better. Most of the resulting spectra have moderate signal-to-noise, S/.N approx. greater than 30 per pixel. The time coverage for these spectra is excellent. Typically, we acquired spectra every 1-2 nights during dark runs at Mt. Hopkins. These data cover most of the rise and all of the decline of the recent outburst. The spectra show a wealth of emission lines, including H I, He I, He II, [Fe V11], and the Raman scattering bands at 6830 A and 7088 A. The Raman bands and other high ionization features vary considerably throughout the outburst. These features will enable us to correlate variations in the FUSE spectra with variations in the optical spectra. Second, we began an analysis of FUSE spectra of Z And. We have carefully examined the spectra, identifying real features and defects. We have identified and measured fluxes for all strong emission lines, including the O VI doublet at 1032 A and 1038 A. These and several other strong emission lines display pronounced P Cygni absorption components indicative of outgrowing gas. We will attempt to correlate these velocities with similar profiles observed on optical spectra. The line velocities - together

  10. Silica from Ash

    Indian Academy of Sciences (India)

    and may change the product characteristics (colour, etc.). This method of quality assessment is more suitable to workers at the processing site as it does not involve lab-scale analysis. Process. The initial step is extraction of silica from ash as sodium silicate using caustic soda. This reaction is carried out at a temperature.

  11. Aniline incorporated silica nanobubbles

    Indian Academy of Sciences (India)

    Unknown

    2006-09-14

    Sep 14, 2006 ... persed in diverse media. 2. Experimental. 2.1 Materials. Chloroauric acid, trisodium citrate, ... molecules such as ciprofloxacin, we could see the same kind of carbon onion structures inside the silica .... molecule. The supernatant, after precipitation of ani- line@SiO2 by centrifugation, did not show aniline.

  12. Hydrothermal stability of silica, hybrid silica and Zr-doped hybrid silica membranes

    NARCIS (Netherlands)

    ten Hove, Marcel; Luiten-Olieman, Mieke W.J.; Huiskes, Cindy; Nijmeijer, Arian; Winnubst, Louis

    2017-01-01

    Hybrid silica membranes have demonstrated to possess a remarkable hydrothermal stability in pervaporation and gas separation processes allowing them to be used in industrial applications. In several publications the hydrothermal stability of pure silica or that of hybrid silica membranes are

  13. Fused Silica Ion Trap Chip with Efficient Optical Collection System for Timekeeping, Sensing, and Emulation

    Science.gov (United States)

    2015-01-22

    are shielded from unwanted perturbations. Such traps permit the observation, manipulation, or storage of isolated particles or small groups of...resins to optimize surface wetting with the glass and surface tension forming a smooth outer surface. The third approach involves fabricating a socket ...B) optical port assemblies consisting of a fiber alignment hole, ball lens socket , and conical shaped aperture(s) opening into the trap slot. The

  14. Automated coating procedures to produce poly(ethylene glycol) brushes in fused-silica capillaries

    DEFF Research Database (Denmark)

    Poulsen, Nicklas N; Østergaard, Jesper; Petersen, Nickolaj J

    2017-01-01

    the four model proteins cytochrome c, myoglobin, ovalbumin and human serum albumin in the pH range 3.4-8.4. Further, even samples containing 10% v/v plasma derived from human blood did not show signs of adsorbing to the coated capillaries. The covalent as well as the electrostatically adsorbed coating were...... both found to be stable and provided almost complete suppression of the electroosmotic flow in the pH range 3.4-8.4. The coating procedures may easily be integrated in fully automated capillary electrophoresis methodologies. This article is protected by copyright. All rights reserved........ Flexible and reliable approaches for preventing unwanted protein adsorption in separation science are thus in high demand. We therefore present new coating approaches based on an automated in-capillary surface initiated atom transfer radical polymerization process (covalent coating) as well...

  15. Capillary electrophoresis in a fused-silica capillary with surface roughness gradient

    Czech Academy of Sciences Publication Activity Database

    Horká, Marie; Šlais, Karel; Karásek, Pavel; Růžička, F.; Šalplachta, Jiří; Šesták, Jozef; Kahle, Vladislav; Roth, Michal

    2016-01-01

    Roč. 39, č. 19 (2016), s. 3827-3834 ISSN 1615-9306 R&D Projects: GA ČR(CZ) GA16-03749S; GA MZd(CZ) NV16-29916A Institutional support: RVO:68081715 Keywords : capillary electrophoresis * supercritical water * surface roughness gradient Subject RIV: CB - Analytical Chemistry , Separation Impact factor: 2.557, year: 2016

  16. Hollow Core Optical Fiber Gas Lasers: Toward Novel and Practical Systems in Fused Silica

    Science.gov (United States)

    2017-05-18

    release. John Luginsland Hollow-Core Optical Fiber Gas Lasers K. Corwin et al. 16 Fig. 18 (a) The mode- locked Tm/Ho...18. NUMBER OF PAGES 19a.  NAME OF RESPONSIBLE PERSON LUGINSLAND, JOHN 19b.  TELEPHONE NUMBER (Include area code) 703-588-1775 Standard Form 298 (Rev. 8...for public release. John Luginsland FA9550-14-1-0024 Final Report K. Corwin et al. 1 A. Project Summary/Abstract Hollow Core Optical Fiber Gas

  17. Isoelectric focusing in continuously tapered fused silica capillary prepared by etching with supercritical water

    Czech Academy of Sciences Publication Activity Database

    Šlais, Karel; Horká, Marie; Karásek, Pavel; Planeta, Josef; Roth, Michal

    2013-01-01

    Roč. 85, č. 9 (2013), s. 4296-4300 ISSN 0003-2700 R&D Projects: GA ČR(CZ) GAP106/12/0522; GA MV VG20102015023 Institutional support: RVO:68081715 Keywords : capillary isoelectric focusing * resolution of ampholytes * supercritical water Subject RIV: CB - Analytical Chemistry, Separation Impact factor: 5.825, year: 2013

  18. Polishing for glass ceramics: which protocol?

    Science.gov (United States)

    Silva, Tânia Mara da; Salvia, Ana Carolina Rodrigues Danzi; Carvalho, Rodrigo Furtado de; Pagani, Clovis; Rocha, Daniel Maranha da; Silva, Eduardo Galera da

    2014-07-01

    The execution of adjustments on ceramic restorations is sometimes necessary for either correction of occlusion and/or inadequate contours or esthetical improvements. Clinically, the surfaces undergo weariness through fine grinding diamond burs which remove the superficial glazing layer. Several materials for ceramic polishing have been used in an attempt to reach a satisfactory surface smoothness. The aim of this study was to perform a literature review on different polishing protocols of several dental ceramics. This is a literature review performed through scientific articles published between 2004 and 2012, indexed in MEDLINE, PubMed and Scielo databases. The study selected and analyzed a total of 20 relevant articles that evaluated different types of ceramics, polishing treatment and surface roughness. After an extensive literature review, this study observed: 1 - after the rupture of the glazing layer due to the adjustments of the restorations, the best choice for the polishing of the surface will depend on the type of ceramics used; 2 - glazing procedure provide excellent results regarding to the superficial smoothness; however, if reglazing is impossible, either abrasive rubber cups/points or sandpaper discs followed by the use of diamond polishing pastes results in a satisfactory superficial smoothness; 3 - clinical studies that take into account the behavior of the protocols polishing are scarce and should be encouraged; 4 - the large number of variables influence the final outcome of polishing should be considered. The necessity in standardization of methodologies to enable a comparison among researches. Copyright © 2014 Japan Prosthodontic Society. Published by Elsevier Ltd. All rights reserved.

  19. Smoking characteristics of Polish immigrants in Dublin.

    LENUS (Irish Health Repository)

    Kabir, Zubair

    2008-01-01

    BACKGROUND: This study examined two main hypotheses: a) Polish immigrants\\' smoking estimates are greater than their Irish counterparts (b) Polish immigrants purchasing cigarettes from Poland smoke "heavier" (>\\/= 20 cigarettes a day) when compared to those purchasing cigarettes from Ireland. The study also set out to identify significant predictors of \\'current\\' smoking (some days and everyday) among the Polish immigrants. METHODS: Dublin residents of Polish origin (n = 1,545) completed a previously validated Polish questionnaire in response to an advertisement in a local Polish lifestyle magazine over 5 weekends (July-August, 2007). The Office of Tobacco Control telephone-based monthly survey data were analyzed for the Irish population in Dublin for the same period (n = 484). RESULTS: Age-sex adjusted smoking estimates were: 47.6% (95% Confidence Interval [CI]: 47.3%; 48.0%) among the Poles and 27.8% (95% CI: 27.2%; 28.4%) among the general Irish population (p < 0.001). Of the 57% of smokers (n = 345\\/606) who purchased cigarettes solely from Poland and the 33% (n = 198\\/606) who purchased only from Ireland, 42.6% (n = 147\\/345) and 41.4% (n = 82\\/198) were "heavy" smokers, respectively (p = 0.79). Employment (Odds Ratio [OR]: 2.89; 95% CI: 1.25-6.69), lower education (OR: 3.76; 95%CI: 2.46-5.74), and a longer stay in Ireland (>24 months) were significant predictors of current smoking among the Poles. An objective validation of the self-reported smoking history of a randomly selected sub-sample immigrant group, using expired carbon monoxide (CO) measurements, showed a highly significant correlation coefficient (r = 0.64) of expired CO levels with the reported number of cigarettes consumed (p < 0.0001). CONCLUSION: Polish immigrants\\' smoking estimates are higher than their Irish counterparts, and particularly if employed, with only primary-level education, and are overseas >2 years.

  20. Defect production in silica glasses under gamma-irradiation at the quenched nuclear reactor

    International Nuclear Information System (INIS)

    Mussaeva, M.A.; Kalanov, M.U.; Ibragimova, E.M.; Sandalov, V.N.; Muminov, M.L.

    2004-01-01

    Full text: Radiation defect production in oxides is highly interesting for atom and solar energy, and also for burying nuclear waste. Combine effect of neutron and gamma-radiation on materials was studied extensively and only neutrons are believed to displace atoms, although 60 Co-gamma quanta were proved to displace light anions (O, F) by inelastic mechanism. On the example of polished plates of pure fused quartz and barium-silica glasses containing nano-crystalline inclusions, and also nano-porous glass, the effect of gamma-radiation of the quenched reactor was studied in the energy range of 0.2-7 MeV. The time period was selected when practically constant current ∼10-20 nA is maintained in the ionizing chamber, corresponding to the average gamma-flux of 15-30 Gy/s. Optical absorption and photoluminescence spectra and also structure of the grasses were studied. It turned out, that the charged oxygen vacancies accumulation rate is higher in Barium glass than in the pure one, because for SiO 2 with small Z the photoelectric effect is weak, while the Compton scattering and photonuclear reactions prevail, and for Barium - just the opposite. The radiation-induced growth of the crystalline precipitates was noticed in the both glasses, which before had been attributed to the elastic atom displacements by fast neutrons. The density of Ba-glass increases with irradiation. The efficiency of defect production by the gamma-component even of the quenched reactor turned out much higher than that under irradiation with 60 Co gamma-source of ∼1.25 MeV to the equivalent dose at the current dose rate of ∼ 7 Gy/s (and before at 45 Gy/s). A 100-times increase of the surface proton conductivity was discovered in the porous glasses under gamma-irradiation due to water vapor radiolysis on the pore surface. The irradiated porous glass is recommended as an active electrode in the hydrogen fuel element. The work was done under the grant F2.1.2 from Center of Science and Technology

  1. Impact of mechanical stress induced in silica vacuum windows on laser-induced damage.

    Science.gov (United States)

    Gingreau, Clémence; Lanternier, Thomas; Lamaignère, Laurent; Donval, Thierry; Courchinoux, Roger; Leymarie, Christophe; Néauport, Jérôme

    2018-04-15

    At the interface between vacuum and air, optical windows must keep their optical properties, despite being subjected to mechanical stress. In this Letter, we investigate the impact of such stress on the laser-induced damage of fused silica windows at the wavelength of 351 nm in the nanosecond regime. Different stress values, from 1 to 30 MPa, both tensile and compressive, were applied. No effect of the stress on the laser-induced damage was evidenced.

  2. APS 3D: a new benchmark in aspherical polishing

    Science.gov (United States)

    Gauch, Daniel; Mikulic, Dalibor; Veit, Christian

    2017-10-01

    The APS 3D system performs polishing and form correction in one step in order to reduce overall process time, reduce the number of polishing steps required and eliminate the need for highly skilled operators while providing a repeatable polishing process. This new 3D Polishing system yields better surface quality, and a better slope error, automatically determining the optimum speeds, feed rates and polish pressures to achieve a deterministic process based on the required quality parameters input by the operator. The process flow is always the same to ensure consistent quality and target quality values are defined before polishing begins.

  3. Material removal mechanisms in abrasive vibration polishing of complex molds

    Science.gov (United States)

    Brinksmeier, E.; Riemer, O.; Schulte, H.

    2010-10-01

    Optical and medical industries are demanding a large variety of optical elements exhibiting complex geometries and multitude opto-functional areas in the range of a few millimeters [1]. Therefore, mold inserts made of steel or carbides must be finished by polishing for the replication of glass and plastic lenses [2]. For polishing theses complex components in the shape of localized cavities or grooves the application of rotating polishing pads is very limited. Established polishing processes are not applicable, so state of the art is a time consuming and therefore expensive polishing procedures by hand. An automated process with conventional polishing machines is impossible because of the complex mold insert geometry. The authors will present the development of a new abrasive polishing process for finishing these complex mold geometries to optical quality. The necessary relative velocity in the contact area between polishing pad and workpiece surface is exclusively realized by vibration motions which is an advantage over vibration assisted rotating polishing processes. The absence of rotation of the pad opens up the possibility to machine new types of surface geometries. The specific influence factors of vibration polishing were analyzed and will be presented. The determination of material removal behavior and polishing effect on planar steel samples has shown that the conventional abrasive polishing hypothesis of Preston is applicable to the novel vibration polishing process. No overlaid chemical material removal appears.

  4. Polish Academy of Sciences Great Dictionary of Polish [Wielki słownik języka polskiego PAN

    Directory of Open Access Journals (Sweden)

    Piotr Žmigrodzki

    2014-12-01

    Full Text Available The paper describes a lexicographical project involving the development of the newest general dictionary of the Polish language: the Polish Academy of Sciences Great Dictionary of Polish [Wielki słownik języka polskiego PAN]. The project is coordinated by the Institute of Polish Language at the Polish Academy of Sciences and carried out in collaboration with linguists and lexicographers from several other Polish academic centres. The paper offers a brief description of the genesis of the project and the scope of information included in the dictionary, the organisation of work, the life of the dictionary on the Web as well as the plans for the future.

  5. Fused Reality for Enhanced Flight Test Capabilities

    Science.gov (United States)

    Bachelder, Ed; Klyde, David

    2011-01-01

    The feasibility of using Fused Reality-based simulation technology to enhance flight test capabilities has been investigated. In terms of relevancy to piloted evaluation, there remains no substitute for actual flight tests, even when considering the fidelity and effectiveness of modern ground-based simulators. In addition to real-world cueing (vestibular, visual, aural, environmental, etc.), flight tests provide subtle but key intangibles that cannot be duplicated in a ground-based simulator. There is, however, a cost to be paid for the benefits of flight in terms of budget, mission complexity, and safety, including the need for ground and control-room personnel, additional aircraft, etc. A Fused Reality(tm) (FR) Flight system was developed that allows a virtual environment to be integrated with the test aircraft so that tasks such as aerial refueling, formation flying, or approach and landing can be accomplished without additional aircraft resources or the risk of operating in close proximity to the ground or other aircraft. Furthermore, the dynamic motions of the simulated objects can be directly correlated with the responses of the test aircraft. The FR Flight system will allow real-time observation of, and manual interaction with, the cockpit environment that serves as a frame for the virtual out-the-window scene.

  6. Surface Roughness and Gloss of Actual Composites as Polished With Different Polishing Systems.

    Science.gov (United States)

    Rodrigues-Junior, S A; Chemin, P; Piaia, P P; Ferracane, J L

    2015-01-01

    This in vitro study evaluated the effect of polishing with different polishing systems on the surface roughness and gloss of commercial composites. One hundred disk-shaped specimens (10 mm in diameter × 2 mm thick) were made with Filtek P-90, Filtek Z350 XT, Opallis, and Grandio. The specimens were manually finished with #400 sandpaper and polished by a single operator using three multistep systems (Superfix, Diamond Pro, and Sof-lex), one two-step system (Polidores DFL), and one one-step system (Enhance), following the manufacturer's instructions. The average surface roughness (μm) was measured with a surface profilometer (TR 200 Surface Roughness Tester), and gloss was measured using a small-area glossmeter (Novo-Curve, Rhopoint Instrumentation, East Sussex, UK). Data were analyzed by two-way analysis of variance and Tukey's test (α=0.05). Statistically significant differences in surface roughness were identified by varying the polishing systems (pGrandio when polished with Sof-Lex and Filtek Z250 and Opallis when polished with Enhance. Gloss was influenced by the composites (p<0.0001), the polishing systems (p<0.0001), and the interaction between them (p<0.0001). The one-step system, Enhance, produced the lowest gloss for all composites. Surface roughness and gloss were affected by composites and polishing systems. The interaction between both also influenced these surface characteristics, meaning that a single polishing system will not behave similarly for all composites. The multistep systems produced higher gloss, while the one-step system produced the highest surface roughness and the lowest gloss of all.

  7. Fused upper central incisors: management of two clinical cases

    OpenAIRE

    Sfasciotti, Gian Luca; Marini, Roberta; Bossù, Maurizio; Ierardo, Gaetano; Annibali, Susanna

    2012-01-01

    This paper reports the management of two clinical cases, in which the upper right central incisor was fused with a supernumerary tooth and the upper left central incisor was macrodontic. A radiographic examination revealed that the fused teeth had two separate roots. Hemisectioning of the fused teeth was performed, the supernumerary portion was extracted and the remaining part was reshaped to remove any sharp margins and to achieve a normal morphology. The macrodontic central incisors were no...

  8. A novel approach of chemical mechanical polishing for a titanium alloy using an environment-friendly slurry

    Science.gov (United States)

    Zhang, Zhenyu; Shi, Zhifeng; Du, Yuefeng; Yu, Zhijian; Guo, Liangchao; Guo, Dongming

    2018-01-01

    In this study, a novel approach of CMP is developed using an environment-friendly slurry consisting of silica, hydrogen peroxide (H2O2), malic acid and deionized water. This is different from the traditional polishing, in which hazardous chemicals are used for Ti alloys. The surface roughness Ra of 0.68 nm is obtained over a measurement area of 70 × 53 μm2, which is lower than those previously reported for a Ti alloy. This is polished by the developed optimal CMP slurry. Polishing mechanism is investigated using electrochemical and X-ray photoelectron (XPS) measurements. H2O2 dominates the corrosion process during CMP using the developed environment-friendly slurry. Corrosion current of H2O2 is consistent with the reactants of titania, alumina and vanadia formed on the surfaces of Ti-6Al-4 V after CMP. Corrosion potential agrees well with the polished surface quality of Ti-6Al-4 V. Chemical reaction equations are proposed according to the electrochemical and XPS measurements. The developed CMP slurry sheds light on the application in environment protection for the Ti, Ti alloys and CMP industries.

  9. A Radiographic Study of Fused and Geminated Tooth

    Energy Technology Data Exchange (ETDEWEB)

    Park, Chul Jae; Lee, Sang Rae [Dept. of Oral Radiology, College of Dentistry, Kyunhee University, Seoul (Korea, Republic of)

    1990-02-15

    The incidence and several characteristic features of fused and geminated teeth were studied radiographically, with full mouth periapical radiogram and pantomogram, in 4201 patients of mixed dentition and 5358 patients of permanent dentition. The obtained results were as follows: 1. The prevalence was revealed to 2.86%, 0.32%, 0.33%, and 0.06% in deciduous fused tooth, permanent fused tooth, deciduous geminated tooth and permanent geminated tooth respectively, and these anomalies were occurred in female more than male. 2. Fused teeth were observed predominantly in lower anterior teeth area, especially in lateral incisor and canine region, and many cases of deciduous geminated tooth were observed in upper central incisor region. 3. Congenital missing rates of succedaneous tooth in deciduous fused teeth were 57.1%, 85.7%, 71.0%, 69.0% in upper right and left central-lateral incisor regions, lower right and left lateral incisor-canine regions, respectively. 4. Prevalence of dental caries was 42.3%, 18.8% and 5.6% in deciduous fused, deciduous geminated and permanent fused tooth, respectively. 5. In classifying of fused and geminated teeth into 9 type, by following appearance such as number of crown, root, pulp chamber and pulp canal of those teeth, it was more favorable that Type I (2 crown, 2 root, 2 pulp chamber, 2 pulp canal) in deciduous fused tooth and Type IX (1 crown, 1 root, 1 pulp chamber, 1 pulp canal) in permanent used tooth, deciduous and permanent geminated tooth.

  10. A Radiographic Study of Fused and Geminated Tooth

    International Nuclear Information System (INIS)

    Park, Chul Jae; Lee, Sang Rae

    1990-01-01

    The incidence and several characteristic features of fused and geminated teeth were studied radiographically, with full mouth periapical radiogram and pantomogram, in 4201 patients of mixed dentition and 5358 patients of permanent dentition. The obtained results were as follows: 1. The prevalence was revealed to 2.86%, 0.32%, 0.33%, and 0.06% in deciduous fused tooth, permanent fused tooth, deciduous geminated tooth and permanent geminated tooth respectively, and these anomalies were occurred in female more than male. 2. Fused teeth were observed predominantly in lower anterior teeth area, especially in lateral incisor and canine region, and many cases of deciduous geminated tooth were observed in upper central incisor region. 3. Congenital missing rates of succedaneous tooth in deciduous fused teeth were 57.1%, 85.7%, 71.0%, 69.0% in upper right and left central-lateral incisor regions, lower right and left lateral incisor-canine regions, respectively. 4. Prevalence of dental caries was 42.3%, 18.8% and 5.6% in deciduous fused, deciduous geminated and permanent fused tooth, respectively. 5. In classifying of fused and geminated teeth into 9 type, by following appearance such as number of crown, root, pulp chamber and pulp canal of those teeth, it was more favorable that Type I (2 crown, 2 root, 2 pulp chamber, 2 pulp canal) in deciduous fused tooth and Type IX (1 crown, 1 root, 1 pulp chamber, 1 pulp canal) in permanent used tooth, deciduous and permanent geminated tooth.

  11. Microbiological flora and nail polish: a brief report.

    Science.gov (United States)

    Rayan, G M; Flournoy, D J; Schlageter, P

    1994-11-01

    Removing nail polish and prosthetic nails from operating room (OR) personnel prior to scrubbing and from patients prior to hand surgery is recommended but not practiced in many hospitals. There is concern that nail polish can act as a vehicle for the transfer of infectious agents. This study was designed to determine the incidence of microbiological flora of nail polish in a clinical setting.

  12. Monitoring of Robot Assisted Polishing through parameters of acoustic emission

    DEFF Research Database (Denmark)

    Lazarev, Ruslan; Top, Søren; Bilberg, Arne

    The polishing process is essential for the surface generation of machine tooling components in advanced manufacturing. While robot assisted polishing is faster and more consistent than manual polishing, it can still consume a significant part of ma- chining time and operator presence time...

  13. 21 CFR 872.6030 - Oral cavity abrasive polishing agent.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Oral cavity abrasive polishing agent. 872.6030... (CONTINUED) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6030 Oral cavity abrasive polishing agent. (a) Identification. An oral cavity abrasive polishing agent is a device in paste or powder form...

  14. Understanding error generation in fused deposition modeling

    International Nuclear Information System (INIS)

    Bochmann, Lennart; Transchel, Robert; Wegener, Konrad; Bayley, Cindy; Helu, Moneer; Dornfeld, David

    2015-01-01

    Additive manufacturing offers completely new possibilities for the manufacturing of parts. The advantages of flexibility and convenience of additive manufacturing have had a significant impact on many industries, and optimizing part quality is crucial for expanding its utilization. This research aims to determine the sources of imprecision in fused deposition modeling (FDM). Process errors in terms of surface quality, accuracy and precision are identified and quantified, and an error-budget approach is used to characterize errors of the machine tool. It was determined that accuracy and precision in the y direction (0.08–0.30 mm) are generally greater than in the x direction (0.12–0.62 mm) and the z direction (0.21–0.57 mm). Furthermore, accuracy and precision tend to decrease at increasing axis positions. The results of this work can be used to identify possible process improvements in the design and control of FDM technology. (paper)

  15. Understanding error generation in fused deposition modeling

    Science.gov (United States)

    Bochmann, Lennart; Bayley, Cindy; Helu, Moneer; Transchel, Robert; Wegener, Konrad; Dornfeld, David

    2015-03-01

    Additive manufacturing offers completely new possibilities for the manufacturing of parts. The advantages of flexibility and convenience of additive manufacturing have had a significant impact on many industries, and optimizing part quality is crucial for expanding its utilization. This research aims to determine the sources of imprecision in fused deposition modeling (FDM). Process errors in terms of surface quality, accuracy and precision are identified and quantified, and an error-budget approach is used to characterize errors of the machine tool. It was determined that accuracy and precision in the y direction (0.08-0.30 mm) are generally greater than in the x direction (0.12-0.62 mm) and the z direction (0.21-0.57 mm). Furthermore, accuracy and precision tend to decrease at increasing axis positions. The results of this work can be used to identify possible process improvements in the design and control of FDM technology.

  16. Fusing Recommendations for Social Bookmarking Websites

    DEFF Research Database (Denmark)

    Bogers, Toine; van den Bosch, Antal

    2011-01-01

    Social bookmarking websites are rapidly growing in popularity. Recommender systems, a promising remedy to the information overload accompanying the explosive growth in content, are designed to identify which unseen content might be of interest to a particular user, based on his or her past...... that use tag overlap and metadata provide better results for social bookmarking data sets than the transaction patterns that are used traditionally in recommender systems research. In addition, we investigate how to fuse different recommendation approaches to further improve recommendation accuracy. We...... preferences. Most previous work in recommendation for social bookmarking suffers from a lack of comparisons between the different available approaches. In this article, we address this issue by comparing and evaluating eight recommendation approaches on four data sets from two domains. We find that approaches...

  17. Fused Entropy Algorithm in Optical Computed Tomography

    Directory of Open Access Journals (Sweden)

    Xiong Wan

    2014-02-01

    Full Text Available In most applications of optical computed tomography (OpCT, limited-view problems are often encountered, which can be solved to a certain extent with typical OpCT reconstructive algorithms. The concept of entropy first emerged in information theory has been introduced into OpCT algorithms, such as maximum entropy (ME algorithms and cross entropy (CE algorithms, which have demonstrated their superiority over traditional OpCT algorithms, yet have their own limitations. A fused entropy (FE algorithm, which follows an optimized criterion combining self-adaptively ME with CE, is proposed and investigated by comparisons with ME, CE and some traditional OpCT algorithms. Reconstructed results of several physical models show this FE algorithm has a good convergence and can achieve better precision than other algorithms, which verifies the feasibility of FE as an approach of optimizing computation, not only for OpCT, but also for other image processing applications.

  18. Photochemical welding of silica microspheres to silicone rubber by ArF excimer laser

    Science.gov (United States)

    Okoshi, Masayuki; Iyono, Minako; Inoue, Narumi; Yamashita, Tsugito

    2009-09-01

    Transparent fused silica (SiO 2) microspheres 2.5 μm in diameter were photochemically welded to transparent, flexible silicone rubber ([SiO(CH 3) 2] n) substrate by 193 nm ArF excimer laser induced photochemical modification of silicone into silicon oxide. Single layer of silica microspheres was easily formed on an adhesive silicone rubber before laser irradiation after dropping of silica microspheres dispersed in ethanol and subsequent tape peeling. The welding rate, the percentage of welded microspheres tested by ultrasonic cleaning with ethanol, was examined by varying the single pulse fluence and irradiation time of ArF excimer laser. The welding layer underneath microsphere, silicon oxide, was also found to emit white light of strong intensity under UV light illumination.

  19. Biofunctionalization of silica-coated magnetic particles mediated by a peptide

    Science.gov (United States)

    Care, Andrew; Chi, Fei; Bergquist, Peter L.; Sunna, Anwar

    2014-08-01

    A linker peptide sequence with affinity to silica-containing materials was fused to Streptococcus protein G', an antibody-binding protein. This recombinant fusion protein, linker-protein G (LPG) was produced in E. coli and exhibited strong affinity to silica-coated magnetic particles and was able to bind to them at different pHs, indicating a true pH-independent binding. LPG was used as an anchorage point for the oriented immobilization of antibodies onto the surface of the particles. These particle-bound "LPG-Antibody complexes" mediated the binding and recovery of different cell types (e.g., human stem cells, Legionella, Cryptosporidium and Giardia), enabling their rapid and simple visualization and identification. This strategy was used also for the efficient capture of Cryptosporidium oocysts from water samples. These results demonstrate that LPG can mediate the direct biofunctionalization of silica-coated magnetic particles without the need for complex surface chemical modification.

  20. Professional Training of Economists at Polish Universities

    Science.gov (United States)

    Ogienko, Olena

    2016-01-01

    Polish experience in professional training of economists at university has been generalized. Structural, content and procedural peculiarities of the training have been defined. It has been proved that key factors for reforming economic education in Poland are globalization, internationalization, integration, technologization and informatization.…

  1. Knowledge Mobilisation in the Polish Education System

    Science.gov (United States)

    Fazlagic, Jan; Erkol, Arif

    2015-01-01

    Poland has made substantial progress in improving the quality of its education system in recent years. This paper aims to describe the situation of the Polish education system from a knowledge management perspective and, to some extent, through innovation policies in education. The many challenges, this paper argues, can be tackled only through…

  2. Sexual Health of Polish Athletes with Disabilities

    Directory of Open Access Journals (Sweden)

    Ryszard Plinta

    2015-06-01

    Full Text Available The purpose of this study was to determine sexual functioning of Polish athletes with disabilities (including paralympians. The study encompassed 218 people with physical disabilities, aged between 18 and 45 (149 men and 69 women. The entire research population was divided into three groups: Polish paralympians (n = 45, athletes with disabilities (n = 126 and non-athletes with disabilities (n = 47. The quality of sexual life of Polish paralympians was measured by using the Polish version of Female Sexual Function Index and International Index of Erectile Function. Clinically significant erectile dysfunctions were most often diagnosed in non-athletes (83.33% with 50% result of severe erectile dysfunctions, followed by athletes and paralympians with comparable results of 56.98% and 54.17% respectively (p = 0.00388. Statistically significant clinical sexual dysfunctions concerned lubrication, orgasm as well as pain domains, and prevailed among female non-athletes (68.42%, 68.42% and 57.89%. Practising sports at the highest level has a favourable effect on the sexuality of men and women with physical disabilities. Men with physical disabilities manifest more sexual disorders than women, an aspect which should be considered by health-care professionals working with people with disabilities.

  3. Technological Advances of Robot Assisted Polishing

    DEFF Research Database (Denmark)

    Lazarev, Ruslan; Top, Søren; Grønbæk, Jens

    The efficient polishing of surfaces is very important in mould and die industry. Fine abrasive processes are widely used in industry for the first steps for the production of tools of high quality in terms of finishing accuracy, form and surface integrity. While manufacturing of most components r...

  4. Polish Complementary Schools in Iceland and England

    Science.gov (United States)

    Zielinska, Malgorzata; Kowzan, Piotr; Ragnarsdóttir, Hanna

    2014-01-01

    Since 2004, the opening of labour markets has spurred a considerable number of Poles to emigrate e.g. to Iceland and England. Families with school age children have had the challenge of adapting to foreign environments and school systems. Polish complementary schools have played an important, albeit ambivalent, role in this process. Through focus…

  5. Hydrothermal stability of microporous silica and niobia-silica membranes

    NARCIS (Netherlands)

    Boffa, V.; Blank, David H.A.; ten Elshof, Johan E.

    2008-01-01

    The hydrothermal stability of microporous niobia–silica membranes was investigated and compared with silica membranes. The membranes were exposed to hydrothermal conditions at 150 and 200 °C for 70 h. The change of pore structure before and after exposure to steam was probed by single-gas permeation

  6. Transformation of the Polish Banking Sector

    Directory of Open Access Journals (Sweden)

    Marek Stefański

    2009-07-01

    Full Text Available In the post-war period the banking system in Poland underwent two important system transitions: after 1946 and after 1989. The third transformation began after May 1, 2004, but it did not have a systemic character. The Polish banking sector started to operate on the Single European Market. The first part of the paper is devoted to the problems of the banks transformations after 1989 with a special focus on the quantitative development of banks in 19892008, and on subsequent privatisation and consolidation processes. The former intensified in 19891999, and the latter in 19992002. The consolidation process was very noticeable in the sector of cooperative banks after 1994. The second part of the paper includes an economic and financial analysis of the banks. A lot of attention was paid to the liquidity of the banking sector. It was assessed as good, which was confirmed by a short-term rating of Moodys and by the Financial Stability Report 2009, published by the National Bank of Poland in June 2009. The comparison of the net profit of the banking sector in 19972008 shows its dependence on the economic situation and policy. The number of banks with capital adequacy ratio well above the minimum required by the banking supervision is rising. The financial power ratings are not favorable for the domestic banks. The third part of the paper focuses on the development directions of the Polish banking sector. It may be concluded on the basis of the analysis that privatisation and consolidation processes will be continued. They will concentrate on the capital of foreign banks already operating in Poland. As compared with individual foreign banks, the potential of the Polish banking sector is week. The fourth part of the paper focuses on the presentation Polish banking sector in the context of European Union banking sector. The paper finishes with conclusions. Generally, Polish banks have to implement a strategy to enable them to compete on the Single

  7. Chemical mechanical glass polishing with cerium oxide: Effect of selected physico-chemical characteristics on polishing efficiency

    Czech Academy of Sciences Publication Activity Database

    Janoš, P.; Ederer, J.; Pilařová, V.; Henych, Jiří; Tolasz, Jakub; Milde, D.; Opletal, T.

    2016-01-01

    Roč. 362, SEP (2016), s. 114-120 ISSN 0043-1648 R&D Projects: GA MŠk(CZ) LM2015073 Institutional support: RVO:61388980 Keywords : Chemical mechanical polishing * Ceria-based polishing powders * Polishing efficienc Subject RIV: CA - Inorganic Chemistry Impact factor: 2.531, year: 2016

  8. Novel 3-hydroxypropyl-bonded phase by direct hydrosilylation of allyl alcohol on amorphous hydride silica.

    Science.gov (United States)

    Gómez, Jorge E; Navarro, Fabián H; Sandoval, Junior E

    2014-09-01

    A novel 3-hydroxypropyl (propanol)-bonded silica phase has been prepared by hydrosilylation of allyl alcohol on a hydride silica intermediate, in the presence of platinum (0)-divinyltetramethyldisiloxane (Karstedt's catalyst). The regio-selectivity of this synthetic approach had been correctly predicted by previous reports involving octakis(dimethylsiloxy)octasilsesquioxane (Q8 M8 (H) ) and hydrogen silsesquioxane (T8 H8 ), as molecular analogs of hydride amorphous silica. Thus, C-silylation predominated (∼94%) over O-silylation, and high surface coverages of propanol groups (5 ± 1 μmol/m(2) ) were typically obtained in this work. The propanol-bonded phase was characterized by spectroscopic (infrared (IR) and solid-state NMR on silica microparticles), contact angle (on fused-silica wafers) and CE (on fused-silica tubes) techniques. CE studies of the migration behavior of pyridine, caffeine, Tris(2,2'-bipyridine)Ru(II) chloride and lysozyme on propanol-modified capillaries were carried out. The adsorption properties of these select silanol-sensitive solutes were compared to those on the unmodified and hydride-modified tubes. It was found that hydrolysis of the SiH species underlying the immobilized propanol moieties leads mainly to strong ion-exchange-based interactions with the basic solutes at pH 4, particularly with lysozyme. Interestingly, and in agreement with water contact angle and electroosmotic mobility figures, the silanol-probe interactions on the buffer-exposed (hydrolyzed) hydride surface are quite different from those of the original unmodified tube. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  9. STUDY OF POLISHING AISI 316L WITH STRUCTURED ABRASIVE

    Directory of Open Access Journals (Sweden)

    François GOOSSENS

    2015-05-01

    Full Text Available Finishing process like polishing is usually used to obtain high quality mechanical surface characteristics such as texture and roughness. These operations are mainly handmade and need highly trained operators thus limiting their repeatability and profitability. To optimize the industrialization of the polishing process, it is therefore necessary to modelize the process to built efficient parameter database. The aim of this study is to characterise the polishing of 316L stainless steel with structured abrasive belts. The geometric data of the belts are given, and we then propose a model to determine material removal. An experimental test bench is set up to test this model and characterise the polishing process in terms of forces. It produces samples for different polishing conditions. The different polished surfaces are then analyzed thanks to the roughness and the wettability. Using experimental designs, we are able to validate the proposed model and identify the parameters that influence a polishing operation.

  10. Silica needle template fabrication of metal hollow microneedle arrays

    International Nuclear Information System (INIS)

    Zhu, M W; Li, H W; Chen, X L; Tang, Y F; Lu, M H; Chen, Y F

    2009-01-01

    Drug delivery through hollow microneedle (HMN) arrays has now been recognized as one of the most promising techniques because it minimizes the shortcomings of the traditional drug delivery methods and has many exciting advantages—pain free and tunable release rates, for example. However, this drug delivery method has been hindered greatly from mass clinical application because of the high fabrication cost of HMN arrays. Hence, we developed a simple and cost-effective procedure using silica needles as templates to massively fabricate HMN arrays by using popular materials and industrially applicable processes of micro- imprint, hot embossing, electroplating and polishing. Metal HMN arrays with high quality are prepared with great flexibility with tunable parameters of area, length of needle, size of hollow and array dimension. This efficient and cost-effective fabrication method can also be applied to other applications after minor alterations, such as preparation of optic, acoustic and solar harvesting materials and devices

  11. Silica needle template fabrication of metal hollow microneedle arrays

    Science.gov (United States)

    Zhu, M. W.; Li, H. W.; Chen, X. L.; Tang, Y. F.; Lu, M. H.; Chen, Y. F.

    2009-11-01

    Drug delivery through hollow microneedle (HMN) arrays has now been recognized as one of the most promising techniques because it minimizes the shortcomings of the traditional drug delivery methods and has many exciting advantages—pain free and tunable release rates, for example. However, this drug delivery method has been hindered greatly from mass clinical application because of the high fabrication cost of HMN arrays. Hence, we developed a simple and cost-effective procedure using silica needles as templates to massively fabricate HMN arrays by using popular materials and industrially applicable processes of micro- imprint, hot embossing, electroplating and polishing. Metal HMN arrays with high quality are prepared with great flexibility with tunable parameters of area, length of needle, size of hollow and array dimension. This efficient and cost-effective fabrication method can also be applied to other applications after minor alterations, such as preparation of optic, acoustic and solar harvesting materials and devices.

  12. Factors Influencing Material Removal And Surface Finish Of The Polishing Of Silica Glasses

    Science.gov (United States)

    2006-01-01

    SiO2), and several metal oxides, namely, ceria ( CeO2 ) and alumina (Al2O3). Abrasive particles for slurries can be obtained in several forms. One of...size and zeta potential measurements were made of three different commercial slurries ( CeO2 , m-ZrO2, and n- Al2O3) used in a slurry recirculation...particle pzc was closest to the slurry pH (i.e. pH 7 for CeO2 , pH 4 for ZrO2, and pH 10 for Al2O3). This seems to support the Cook model, but it was

  13. Fusing website usability and search engine optimisation

    Directory of Open Access Journals (Sweden)

    Eugene B. Visser

    2014-03-01

    Objectives: This research intended to establish a relationship between search engine optimisation and website usability in order to guide the industry. The authors found a discrepancy between the perceived roles of search engines and website usability. Method: The authors designed three test websites. Each had different combinations of usability, visibility and other attributes. They recorded and analysed the conversions and financial spending on these experimental websites. Finally, they designed a model that fuses search engine optimisation and website usability. Results: Initially, it seemed that website usability and search engine optimisation complemented each other. However, some contradictions between the two, based on content, keywords and their presentation, emerged. Industry experts do not acknowledge these contradictions, although they agree on the existence of the individual elements. The new model highlights the complementary and contradictory aspects. Conclusion: The authors found no evidence of any previous empirical experimental results that could confirm or refute the role of the model. In the fast-paced world of competition between commercial websites, this adds value and originality to the websites of organisations whose websites play important roles.

  14. Thermogravimetry analysis on fused borosilicate syntactic foams

    Science.gov (United States)

    Salleh, Zulzamri; Islam, Md Mainul; Epaarachchi, Jayantha Ananda

    2017-12-01

    Fused borosilicate/vinyl ester syntactic foams mostly used for thermal stability in many applications are considered to be characterised for their properties in higher temperature condition. Therefore, higher temperature characteristics need to be explored with respect to physical parameters such as porosity and void content. The filler, also known as glass microballoons, was incorporated in vinyl ester resin matrix in 2wt%, 4wt%, 6wt.%, 8wt.% and 10wt.%. These composites are characterised and degraded to examine the onset temperature, Tonset, peak temperature, Tpeak and end temperature, Tend using thermogravimetric analysis (TGA) method. The results for Tonset showed an increment while Tend and Tpeak showed decrement when glass microballoons were added in syntactic foams. Based on TGA data, they exhibited excellent thermal stability, showing 5% weight loss at 380-450 °C. Glass transition temperature (Tg) decreased when more glass microballoons were added, and also related to the effect on the physical properties of syntactic foams. Therefore, understanding of the relationship between thermal properties of syntactic foams and their physical properties such as porosity and void content will help in developing syntactic foams to optimise their thermal characteristics, which will be beneficial for engineering applications.

  15. Ultralightweight low-temperature fused Zerodur mirror

    Science.gov (United States)

    Miller, Jennifer; Crowe, David A.; Clark, Patrick; Marker, Alexander J.

    1995-09-01

    The performance and utility of optical systems can be significantly improved by using lightweight stable mirror components. Such components have been incorporated into a mirror assembly through a process that utilizes low temperature fusion to bond low CTE faceplates onto a lightweight core structure. The core structure is fabricated using an abrasive waterjet cutting technique that enables the designer to optimize core geometry to enhance the structural performance of the blank. The faceplates are bonded to the lightweight core resulting in a stiff structural mirror. A 15.125 inch Zerodur mirror was fabricated using this unique process and subjected to a test program to measure the optical stability of the mirror in support of either space-based applications. Strength testing was performed to verify the integrity of the fused joints and determine appropriate design allowable stress. A thermal test program was designed to assess performance at various temperature extremes and a mechanical load test was run to verify the capability of the blank to withstand operational loads without degrading the optical surface. The surface figure of the part was measured before, during, and after a 200 degree F temperature cycle with no change in figure quality. In addition, the mirror was subjected to a 10 g load for ten minutes with no change in the figure quality.

  16. SPECTRAL METHODS IN POLISH EMOTIONAL SPEECH RECOGNITION

    Directory of Open Access Journals (Sweden)

    Paweł Powroźnik

    2016-12-01

    Full Text Available In this article the issue of emotion recognition based on Polish emotional speech signal analysis was presented. The Polish database of emotional speech, prepared and shared by the Medical Electronics Division of the Lodz University of Technology, has been used for research. Speech signal has been processed by Artificial Neural Networks (ANN. The inputs for ANN were information obtained from signal spectrogram. Researches were conducted for three different spectrogram divisions. The ANN consists of four layers but the number of neurons in each layer depends of spectrogram division. Conducted researches focused on six emotional states: a neutral state, sadness, joy, anger, fear and boredom. The averange effectiveness of emotions recognition was about 80%.

  17. Polish 2012 growth references for preschool children.

    Science.gov (United States)

    Kułaga, Zbigniew; Grajda, Aneta; Gurzkowska, Beata; Góźdź, Magdalena; Wojtyło, Małgorzata; Swiąder, Anna; Różdżyńska-Świątkowska, Agnieszka; Litwin, Mieczysław

    2013-06-01

    Growth references are useful in monitoring a child's growth, which is an essential part of child care. The aim of this paper is to provide updated growth references for Polish preschool children and to assess how well children in Poland match or diverge from the World Health Organization (WHO) growth standards/references and recent German height-for-age references. The height-, weight-, body mass index-for-age, and weight-for-height references were constructed with the LMS method using data from a recent, large, population-representative sample of 4,941 preschool children aged 3 to 6 years (the OLA study). In the case of boys, the third, 50th, and 97th height percentiles of new Polish and German references overlap almost completely, whereas the WHO growth standards/references percentiles are systematically lower. In the case of girls, comparison between the new Polish and German height references showed conformity on the third and 50th percentile, whereas body height values of the WHO standards/references are shorter. Polish children aged 3 to 6 years from for the nation representative sample, had significantly greater than zero mean z scores of height-, weight-, and BMI-for-age and weight-for-height, relative to the WHO growth standards/references. The number of children in the sample with height-for-age below -2 SD was significantly lower than expected and number of children with height-for-age above +2 SD was significantly higher than expected. The OLA study growth references can be recommended as national references for preschool children in Poland.

  18. Polish normalization of the Body Esteem Scale

    Directory of Open Access Journals (Sweden)

    Małgorzata Lipowska

    2014-02-01

    Full Text Available Background Physical attractiveness plays an important part in one’s social functioning. The interest in one’s own appearance have been documented as widespread among the female population, but over the recent years it is more and more often emphasized that concentrating on body appearance concerns men as well. Franzoi and Shields (1984 created the Body Esteem Scale which allows to qualify the subject’s attitude towards his or her own body. The aim of the study was to create a Polish version of the Body Esteem Scale along with the norms for age and sex clusters. Participants and procedure The normalization sample consisted of 4298 participants: 1865 women aged 16 to 80 (M = 29.92; SD = 12.85 and 2433 men aged 16 to 78 (M = 28.74; SD = 11.50. Education levels among the participants were also controlled for. In order to create a Polish version of the Body Esteem Scale, translation was adopted as the adaptation strategy. Like the original one, the Polish scale comprises 35 items grouped into three gender specific subscales. The subscales for women include Sexual Attractiveness, Weight Concern, and Physical Condition, whereas the body esteem of is examined with regards to Physical Attractiveness, Upper Body Strength, and Physical Condition. Results Reliability of subscales was high both for females (Cronbach’s alpha from 0.80 to 0.89 and males (Cronbach’s alpha from 0.85 to 0.88. The given coefficients of reliability cover the original division into subscales adopted by the authors of BES. Conclusions We confirmed high reliability of the Polish version of the Body Esteem Scale, thus we recommend it as a diagnostic tool. Created norms allowed to refer results obtained in the course of research carried out on people with various disorders (e.g. eating disorders or body dysmorphic disorder with population data for corresponding age brackets.

  19. Polish Martial Law: The Crisis of Communism

    Science.gov (United States)

    2009-12-01

    Roman Catholic Church continued to exist, and a comparatively liberal cultural policy was in place, which continued a legitimate practice of most of...intervention. Their answers verify that for most Poles the fear 29 of losing sovereignty and Polish culture to Russian aggression overshadows all else, even...they going in? They did not,” Woodrow Wilson International Center for Scholars, http://www.wilsoncenter.org/news/ docs/ Historia -Jachranka%20-%20Stan

  20. Periodic mesoporous silica gels

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, M.T.; Martin, J.E.; Odinek, J.G. [and others

    1996-06-01

    We have synthesized monolithic particulate gels of periodic mesoporous silica by adding tetramethoxysilane to a homogeneous alkaline micellar precursor solution. The gels exhibit 5 characteristic length scales over 4 orders of magnitude: fractal domains larger than the particle size (>500 nm), particles that are {approximately}150 to 500 nm in diameter, interparticle pores that are on the order of the particle size, a feature in the gas adsorption measurements that indicates pores {approximately}10-50 nm, and periodic hexagonal arrays of {approximately}3 nm channels within each particle. The wet gel monoliths exhibit calculated densities as low as {approximately}0.02 g/cc; the dried and calcined gels have bulk densities that range from {approximately}0.3-0.5 g/cc. The materials possess large interparticle ({approximately}1.0-2.3 cc/g) and intraparticle ({approximately}0.6 cc/g) porosities.

  1. The Polish Cyborg. A Reflection on the Relationship between Man and Machine in Early Polish Modernism

    Directory of Open Access Journals (Sweden)

    Emiliano Ranocchi

    2016-12-01

    Full Text Available Far from being enthusiastic “modernolatry” of Italian futurism, Polish futurism demonstrates an attitude of ambivalence toward modernity. This is particularly evident in the Polish approach to that very synecdoche of modernity which is the machine. In his essay of 1923, the leader of the group, Bruno Jasieński, compares the fetishistic cult of the machine, which characterizes the Italian approach, with the utilitarian one of the Russians, exemplified by a quote from Majakovskij. To these two propositions, as a sort of Hegelian synthesis, he adds a Polish one consisting in the conception of the machine as a prosthesis, a continuation of the human body. Thereby he introduces an idea later known as “cyborg”. The category of cyborg is also useful to understand the work of another today almost forgotten Polish writer of the Twenties, Jerzy Sosnkowski. He was the author of a short novel, A Car, You and Me (Love of Machines, in which a whole chapter concerns the chief character’s dystopian nightmare wherein machines take control over the world. The third section of the essay deals with the idea of man a machine – an old, 18th century conception, which became actual anew in the 20th century and whose traces we can find among others in a well-known poem by Tytus Czyżewski. Thirty years before N. Wiener, Polish modernists seem to have sensed the social, political and anthropological implications of the mechanization of work.

  2. Characterization and Streptococcus mutans adhesion on air polishing dentin.

    Science.gov (United States)

    Tada, Kazuhiro; Oda, Hirotake; Inatomi, Michitomo; Sato, Soh

    2014-07-01

    Air polishing is known as an effective and time saving tooth cleaning method. However, this method increased surface roughness and bacterial adhesion on dentin surface. The aim of this study was to characterize and examine Streptococcus mutans adhesion on dentin surface after air polishing as compared to the conventional method. The dentin blocks (4 × 4 × 1 mm) were polished by a rubber cup with polishing material (Polishing) and air-polished by 25 μm glycine (G25), 65 μm glycine (G65), and 65 μm sodium bicarbonate (NHC65) microparticles. Surface roughness (Ra) was measured by a laser electron microscope. The amount of adhered S. mutans was quantified using a resazurin reduction assay (alamarBlue(®)). The Ra of G25 and G65 was significantly (p < 0.01) smaller than that of NHC65 and greater than that of Polishing. However, there was no significant difference in S. mutans adhesion among Polishing, G25, and G65, while NHC65 showed significantly (p < 0.01) higher S. mutans adhesion. Within the limitations of this in vitro study, air polishing using glycine microparticles conditioned S. mutans adhesion on dentin surface in a similar fashion than the conventional method, and less than air polishing using sodium bicarbonate microparticles.

  3. Effects of polishing procedures on color stability of composite resins.

    Science.gov (United States)

    Güler, Ahmet Umut; Güler, Eda; Yücel, Ali Cağin; Ertaş, Ertan

    2009-01-01

    The purpose of this study was to investigate the effect of different polishing methods on color stability of posterior, universal and nanohybrid composite resin restorative materials upon exposure to a staining agent. Twenty-five specimens were prepared for each of 5 different composite resins (Filtek Z250, Filtek P60, Quadrant LC, Grandio and Filtek Supreme). Specimens were divided into 5 groups and different polishing procedures, including polishing discs (Pd), polishing discs then diamond polishing paste (PdP), polishing discs then a liquid polishing system (Biscover) (PdB), and combinations of these (PdPB) were used. Unpolished specimens served as the control (C). The specimens were stored for 48 h in a coffee solution. The color of all specimens was measured before and after exposure with a colorimeter, and total color change (DeltaE*) were calculated. The data were analyzed with a two-way ANOVA and the means were compared by Tukey HSD test (alpha=0.05). The lowest color difference was observed in the groups PdP and C, while the highest color difference was observed in PdPB, and PdB. When comparing the five different restorative materials, no significant difference was observed between FiltekP60 and FiltekZ250, and these materials demonstrated significantly less color change than Quadrant LC and the nanohybrid materials (Grandio, Filtek Supreme). The posterior (Filtek P60) and universal (Filtek Z250) composite resin restorative materials, which do not contain tetraethyleneglycol dimethacrylate (TEGDMA), were found to be less stainable than the nanohybrid (Grandio, Filtek Supreme) and universal (Quadrant LC) composite resins, which contain TEGDMA. The use of diamond polishing paste after polishing with polishing discs significantly decreased staining when compared to the groups that used polishing discs alone, for all restorative materials tested. The highest color change values were obtained for the specimens that were polished with the Biscover liquid polish

  4. Effects of polishing procedures on color stability of composite resins

    Directory of Open Access Journals (Sweden)

    Ahmet Umut Güler

    2009-04-01

    Full Text Available The purpose of this study was to investigate the effect of different polishing methods on color stability of posterior, universal and nanohybrid composite resin restorative materials upon exposure to a staining agent. Twenty-five specimens were prepared for each of 5 different composite resins (Filtek Z250, Filtek P60, Quadrant LC, Grandio and Filtek Supreme. Specimens were divided into 5 groups and different polishing procedures, including polishing discs (Pd, polishing discs then diamond polishing paste (PdP, polishing discs then a liquid polishing system (Biscover (PdB, and combinations of these (PdPB were used. Unpolished specimens served as the control (C. The specimens were stored for 48 h in a coffee solution. The color of all specimens was measured before and after exposure with a colorimeter, and total color change (DE* were calculated. The data were analyzed with a two-way ANOVA and the means were compared by Tukey HSD test (a=0.05. The lowest color difference was observed in the groups PdP and C, while the highest color difference was observed in PdPB, and PdB. When comparing the five different restorative materials, no significant difference was observed between FiltekP60 and FiltekZ250, and these materials demonstrated significantly less color change than Quadrant LC and the nanohybrid materials (Grandio, Filtek Supreme. The posterior (Filtek P60 and universal (Filtek Z250 composite resin restorative materials, which do not contain tetraethyleneglycol dimethacrylate (TEGDMA, were found to be less stainable than the nanohybrid (Grandio, Filtek Supreme and universal (Quadrant LC composite resins, which contain TEGDMA. The use of diamond polishing paste after polishing with polishing discs significantly decreased staining when compared to the groups that used polishing discs alone, for all restorative materials tested. The highest color change values were obtained for the specimens that were polished with the Biscover liquid polish

  5. Fused upper central incisors: management of two clinical cases.

    Science.gov (United States)

    Sfasciotti, Gian Luca; Marini, Roberta; Bossù, Maurizio; Ierardo, Gaetano; Annibali, Susanna

    2011-03-01

    This paper reports the management of two clinical cases, in which the upper right central incisor was fused with a supernumerary tooth and the upper left central incisor was macrodontic. A radiographic examination revealed that the fused teeth had two separate roots. Hemisectioning of the fused teeth was performed, the supernumerary portion was extracted and the remaining part was reshaped to remove any sharp margins and to achieve a normal morphology. The macrodontic central incisors were not treated. At 12-months post-surgery there were no periodontal problems and no hypersensitivity. Orthodontic treatment was performed to appropriately align the maxillary teeth and to correct the malocclusion.

  6. Advanced space optics development in freeform optics design, ceramic polishing, rapid and extreme freeform polishing

    Science.gov (United States)

    Geyl, R.; Leplan, H.; Ruch, E.

    2017-09-01

    In this paper Safran-Reosc wants to share with the space community its recent work performed in the domain of space optics. Our main topic is a study about the advantages that freeform optical surfaces can offer to advanced space optics in term of compactness or performances. We have separated smart and extreme freeform in our design exploration work. Our second topic is to answer about the immediate question following: can we manufacture and test these freeform optics? We will therefore present our freeform optics capability, report recent achievement in extreme aspheric optics polishing and introduce to the industrialisation process of large off axis optics polishing for the ESO Extremely Large Telescope primary mirror segments. Thirdly we present our R-SiC polishing layer technology for SiC material. This technique has been developed to reduce costs, risks and schedule in the manufacturing of advanced SiC optics for Vis and IR applications.

  7. Hydrodynamic modelling in the Polish Zone of the Baltic Sea - an overview of Polish achievements

    Directory of Open Access Journals (Sweden)

    Ewa Jasińska

    2003-03-01

    Full Text Available This paper gives a general overview of Polish experience and achievements with regard to hydrodynamic modelling in the Polish zone of the Baltic Sea. The first work started already at the end of the sixties when the first 1D and 2D hydrodynamic models were set up. With the development of numerical methods and increasing computational power a number of 1D, 2D and 3D models were set up and tested. Global, regional and local models cover the most important water bodies,i.e. the Pomeranian Bay - Szczecin Lagoon and Gulf of Gdansk - Vistula Lagoon systems.

  8. Silica-Immobilized Enzyme Reactors

    Science.gov (United States)

    2007-08-01

    metal affinity binding between the ‘his- tag’ and a metal coating ( cobalt ) upon the agarose packing material. The peptide forms silica in situ and...of a nitro group to hydroxylamine resulting in a large electronic change which can be exploited for a variety of biotechnological applications...combined system, or individually as single sequential units will allow for development of complex catalytic sequences. Biologically-derived silica

  9. Fusing Intelligence With Law Enforcement Information: An Analytic Imperative

    National Research Council Canada - National Science Library

    Thornlow, Christopher C

    2005-01-01

    ... and Law Enforcement Communities to fuse and analyze foreign threat intelligence with domestic law enforcement information in a timely fashion to provide adequate indications and warning of such an...

  10. Boeing Delta II rocket for FUSE launch arrives at CCAS

    Science.gov (United States)

    1999-01-01

    At Launch Pad 17A, Cape Canaveral Air Station (CCAS), the first stage of a Boeing Delta II rocket is raised for its journey up the launch tower. The rocket is targeted to launch NASA's Far Ultraviolet Spectroscopic Explorer (FUSE), developed by The Johns Hopkins University under contract to Goddard Space Flight Center, Greenbelt, Md. FUSE will investigate the origin and evolution of the lightest elements in the universe, hydrogen and deuterium. In addition, the FUSE satellite will examine the forces and process involved in the evolution of the galaxies, stars and planetary systems by investigating light in the far ultraviolet portion of the electromagnetic spectrum. FUSE is scheduled to be launched June 23 at CCAS.

  11. IGBT Fuses for Protection Against Explosion in Voltage Source Converters

    DEFF Research Database (Denmark)

    Blaabjerg, Frede; Iov, Florin; Rasmussen, H.

    2004-01-01

    The consequences of electrical faults can be severe; not only to the equipment, but also in the worse case, to people if safety principles are not observed. Every year new applications based on DC-link Voltage Source Converters are added and the demand for protection of power electronics increases...... regarding the high-power IGBT modules. Due to the fact that the power level increases more energy is stored in the DC-link and even with an active protection, a high-power IGBT still has a risk of case rupture (explode) when a circuit failure condition occurs. A possible solution is a protection...... of the converter with standard High Speed Fuses or High Speed IGBT fuses. It is discussed that protection can be achieved by introduction of IGBT fuse located in the DC-link. Experiments show that explosion can be avoided by use of High Speed Fuse protection and the added inductance of standard High Speed...

  12. Polymer Matrix Composites using Fused Deposition Modeling Technology Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Fused deposition modeling (FDM) is an additive manufacturing technology that allows fabrication of complex three-dimensional geometries layer-by-layer. The goal of...

  13. The wear of polished and glazed zirconia against enamel.

    Science.gov (United States)

    Janyavula, Sridhar; Lawson, Nathaniel; Lawson, Nathaniel; Cakir, Deniz; Beck, Preston; Ramp, Lance C; Burgess, John O

    2013-01-01

    The wear of tooth structure opposing anatomically contoured zirconia crowns requires further investigation. The purpose of this in vitro study was to measure the roughness and wear of polished, glazed, and polished then reglazed zirconia against human enamel antagonists and compare the measurements to those of veneering porcelain and natural enamel. Zirconia specimens were divided into polished, glazed, and polished then reglazed groups (n=8). A veneering porcelain (Ceramco3) and enamel were used as controls. The surface roughness of all pretest specimens was measured. Wear testing was performed in the newly designed Alabama wear testing device. The mesiobuccal cusps of extracted molars were standardized and used as antagonists. Three-dimensional (3D) scans of the specimens and antagonists were obtained at baseline and after 200 000 and 400 000 cycles with a profilometer. The baseline scans were superimposed on the posttesting scans to determine volumetric wear. Data were analyzed with a 1-way ANOVA and Tukey Honestly Significant Difference (HSD) post hoc tests (α=.05) Surface roughness ranked in order of least rough to roughest was: polished zirconia, glazed zirconia, polished then reglazed zirconia, veneering porcelain, and enamel. For ceramic, there was no measureable loss on polished zirconia, moderate loss on the surface of enamel, and significant loss on glazed and polished then reglazed zirconia. The highest ceramic wear was exhibited by the veneering ceramic. For enamel antagonists, polished zirconia caused the least wear, and enamel caused moderate wear. Glazed and polished then reglazed zirconia showed significant opposing enamel wear, and veneering porcelain demonstrated the most. Within the limitations of the study, polished zirconia is wear-friendly to the opposing tooth. Glazed zirconia causes more material and antagonist wear than polished zirconia. The surface roughness of the zirconia aided in predicting the wear of the opposing dentition

  14. Tribological approach to study polishing of road surface under traffic

    OpenAIRE

    KANE, Malal; DO, Minh Tan

    2007-01-01

    The polishing phenomenon of road pavements under the vehicle traffic constitutes the main mechanism inherent to the loss of skid resistance over time. A better understanding of this phenomenon would allow an improvement of road safety. This study comprises a review of laboratory test and a model simulating the polishing of road surfaces. The laboratory test uses a polishing machine so called 'Wehner-Schulze' which can reproduce the evolution of the road texture from specimens taken directly f...

  15. Polish Phoneme Statistics Obtained On Large Set Of Written Texts

    Directory of Open Access Journals (Sweden)

    Bartosz Ziółko

    2009-01-01

    Full Text Available The phonetical statistics were collected from several Polish corpora. The paper is a summaryof the data which are phoneme n-grams and some phenomena in the statistics. Triphonestatistics apply context-dependent speech units which have an important role in speech recognitionsystems and were never calculated for a large set of Polish written texts. The standardphonetic alphabet for Polish, SAMPA, and methods of providing phonetic transcriptions are described.

  16. Preparing polished crystal slices with high precision orientation

    DEFF Research Database (Denmark)

    Mathiesen, S. Ipsen; Gerward, Leif; Pedersen, O.

    1974-01-01

    A polishing procedure is described which utilizes a high precision Laue technique for crystal orientation. Crystal slices with their final polished surfaces parallel to a crystallographic plane within 0.02° can be prepared. ©1974 The American Institute of Physics......A polishing procedure is described which utilizes a high precision Laue technique for crystal orientation. Crystal slices with their final polished surfaces parallel to a crystallographic plane within 0.02° can be prepared. ©1974 The American Institute of Physics...

  17. Visible Light Activated Photocatalytic Water Polishing System, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — This proposal targets development of a LED light activated photocatalytic water polishing system that enables reduction of organic impurities (TOC and...

  18. Assessing operability of a novel polisher arrangement using MMS

    International Nuclear Information System (INIS)

    Shor, S.W.W.

    1987-01-01

    A condensate polisher is intended to remove both particulate matter and ionic material from the condensate. Condensate polishers have normally been placed directly in the condensate system downstream of the condensate pumps. This inline location has certain disadvantages. These disadvantages are discussed. Placing the polisher in a sidestream location, where water is removed from the condensate system, pumped through the polisher, and then returned to the condensate system provides a solution to these disadvantages. Several possible types of sidestream installations is described. This has a polisher taking unpolished condensate from one compartment from one compartment of a divided hotwell in a specially modified condenser and returning polished condensate to the other compartment. The polisher is supplied by its own dedicated pumps, which have a head requirement sufficient only to overcome the pressure drop through the polisher circuit at a flow rate of 110% of maximum condensate flow. This concept is very attractive but has not yet been tested even though it is being installed in several new units. A simulation was, therefore, performed using MMS to provide confidence that this particular sidestream polisher arrangement was operationally viable

  19. Effects of metal primers on bonding of adhesive resin cement to noble alloys for porcelain fusing.

    Science.gov (United States)

    Okuya, Nobuhiro; Minami, Hiroyuki; Kurashige, Hisanori; Murahara, Sadaaki; Suzuki, Shiro; Tanaka, Takuo

    2010-03-01

    This study evaluated the effects of metal primers on the bonding of adhesive resin to four pure metals (Au, Pd, Ag, Cu) and two noble alloys for porcelain fusing (high-gold and high-palladium content alloys). Bonding surface was polished with 600-grit silicon carbide paper and primed with one of the three metal primers (V-Primer, Metaltite, and M.L. Primer). Bonded specimens were fabricated by applying adhesive resin (Super-Bond C&B) on the primed surface. Shear bond strength (SBS) was determined both before and after thermocycling (4-60 degrees C for 2,000 cycles). The highest SBS values to each pure metal after thermocycling were 33.5 MPa for Au by M.L. Primer, 35.0 MPa for Ag by V-Primer, and 34.4 MPa for Cu by Metaltite. SBS to high-gold content alloy after thermocycling was 33.3 MPa by M.L. Primer. None of the primers was effective for pure Pd and high-palladium content alloy after thermocycling.

  20. Compressive elastic moduli and polishing performance of non-rigid core/shell structured PS/SiO2 composite abrasives evaluated by AFM

    International Nuclear Information System (INIS)

    Chen, Ailian; Mu, Weibin; Chen, Yang

    2014-01-01

    The core/shell structured polystyrene (PS)/SiO 2 composite microspheres with different silica shell morphology were synthesized by a modified Stöber method. As confirmed by transmission electron microscopy (TEM), the rough discontinuous shell consisted of separate SiO 2 nanoparticles for composite-A, while the smooth continuous one was composed of amorphous silica network for composite-B. Atomic force microscopy (AFM) was employed to probe the compressive Young's moduli (E) and chemical mechanical polishing (CMP) performances of the as-prepared PS/SiO 2 composite microspheres. On the basis of the Hertzian contact mechanics, the calculated E values of the PS microspheres, composite-A and composite-B were 2.9 ± 0.4, 5.1 ± 1.2 and 6.0 ± 1.2 GPa, respectively. Compared to traditional abrasives, thermally grown silicon oxide wafers after polished by the core/shell PS/SiO 2 composite abrasives obtained a lower root mean square roughness and a higher material removal rate value. In addition, there is an obvious effect of shell morphology of the composites on oxide CMP performance and structural stability during polishing process. This approach would provide a basis for understanding the actual role of organic/inorganic core/shell composite abrasives in the material removal process of CMP.

  1. Plasma electrolytic polishing of metalized carbon fibers

    Directory of Open Access Journals (Sweden)

    Falko Böttger-Hiller

    2016-02-01

    Full Text Available Efficient lightweight structures require intelligent materials that meet versatile functions. Especially, carbon-fiber-reinforced polymers (CFRPs are gaining relevance. Their increasing use aims at reducing energy consumption in many applications. CFRPs are generally very light in weight, while at the same time being extremely stiff and strong (specific strength: CFRPs: 1.3 Nm kg–1, steel: 0.27 Nm kg–1; specific stiffness: CFRPs: 100 Nm kg–1, steel: 25 Nm kg–1. To increase performance and especially functionality of CFRPs, the integration of microelectronic components into CFRP parts is aspired. The functionalization by sensors, actuators and electronics can enable a high lightweight factor and a new level of failure-safety. The integration of microelectronic components for this purpose requires a working procedure to provide electrical contacts for a reliable connection to energy supply and data interfaces. To overcome this challenge, metalized carbon fibers are used. Metalized fibers are, similar to the usual reinforcing fibers, able to be soldered and therefore easy to incorporate into CFRPs. Unfortunately, metalized fibers have to be pre-treated by flux-agents. Until now, there is no flux which is suitable for mass production without destroying the polymer of the CFRP. The process of plasma electrolytic polishing (PeP could be an option, but is so far not available for copper. Thus, in this study, plasma electrolytic polishing is transferred to copper and its alloys. To achieve this, electrolytic parameters as well as the electrical setup are adapted. It can be observed that the gloss and roughness can be adjusted by means of this procedure. Finally, plasma electrolytic polishing is used to treat thin copper layers on carbon fibers.

  2. Harvesting silica nanoparticles from rice husks

    International Nuclear Information System (INIS)

    Wang Weixing; Martin, Jarett C.; Zhang Ning; Ma Chao; Han Aijie; Sun Luyi

    2011-01-01

    Biogenic silica nanoparticles were synthesized using rice husks (RHs) as the raw material via controlled pyrolysis. The characterization results showed that the morphology of the synthesized silica was highly related to the pretreatment of RHs and the pyrolysis conditions. Particularly, potassium cations in RHs were found to catalyze the melting of silica, during which the amorphous silica were converted to crystalline phase. Two hours of pyrolysis at 700 °C appeared to be ideal to synthesize silica nanoparticles with a diameter of ca. 20–30 nm. Higher temperature and longer duration of pyrolysis led to undesired melting of silica nanoparticles, while too low a temperature cannot effectively remove carbonous residues. Such amorphous silica nanoparticles with narrow size distribution and high purity are expected to replace silica gel and fumed silica for various applications.

  3. Competence of Irish and Polish Teachers in the Opinions of Young Polish Immigrants in Ireland

    Science.gov (United States)

    Augustyniak, Joanna

    2016-01-01

    Since 2004, Ireland has experienced the arrival of immigrants from various countries from all over the world including Poland. The Polish came to Ireland with their families including children of school age obliged to attend compulsory education. These children have attended schools dissimilar from the ones they are accustomed to in their home…

  4. Wind Directions in the Polish Tatras,

    Science.gov (United States)

    1982-01-26

    The study of anemometric conditions in the iatra Aoun- tains with the usually available observation data presents a rather difficult problem for two...year are presented in Table 2 and Fig. 1. Analysis of the anemometric conditions in the Polish Ta- tras and at 2odhale, on the basis of the observational...Vol. 29, 1947. 9. Milata, W. "The Foehn," Wierchy, Vol. 20, 1950. 10. Orlicz, M. " Anemometric Conditions on Peaks in the 2atras," Wiad. Sluzhby Hydro

  5. Polish students' opinion about medicinal cannabis

    OpenAIRE

    Mazur, Rafał; Masternak, Sebastian; Pająk, Michał; Parszewska, Katarzyna; Skórzyńska-Dziduszko, Katarzyna

    2017-01-01

    Mazur Rafał, Masternak Sebastian, Pająk Michał, Parszewska Katarzyna, Skórzyńska-Dziduszko Katarzyna. Polish students’ opinion about medicinal cannabis. Journal of Education, Health and Sport. 2017;7(9):233-242. eISSN 2391-8306. DOI http://dx.doi.org/10.5281/zenodo.894710 http://ojs.ukw.edu.pl/index.php/johs/article/view/4839 The journal has had 7 points in Ministry of Science and Higher Education parametric evaluation. Part B item 1223 (26....

  6. Thermodynamics of Silica Dissolution From In-situ Raman +Spectroscopy

    Science.gov (United States)

    Davis, M. K.; Fumagalli, P.; Stixrude, L. P.

    2001-12-01

    Solubilities of cations, such as silicon, in water strongly effect both the physical and thermodynamical properties of supercritical metamorphic fluids. Modeling the thermodynamics of fluid-rock interactions requires therefore a profound understanding of cation dissolution and aqueous speciation. In-situ Raman experiments of the silica-water system were performed in an externally heated Bassett-type diamond-anvil cell at the Department of Geological Sciences, University of Michigan. Natural quartz samples (from Owl Creek Mountains, Wyoming) were loaded in the sample chamber with de-ionized or spectrographic water. All experiments used doubly polished rhenium gaskets with a thickness of 200 μ m, diameter of 1.0 mm, and a 500 μ m drillhole for the sample chamber. Temperature was measured using K-type thermocouples wrapped around both the upper and lower diamond anvils. Pressures are obtained on the basis of the shift of the 464 cm-1 Raman mode of quartz. In-situ Raman spectra were collected from 250-1200 cm-1, focusing on the vibrational modes of aqueous silica species at temperatures up to 700 ° C and pressures up to 14 kbar. We observed Si-O stretching modes attributable to dimer (H6Si2O7, 965 cm-1) and monomer (H4SiO4, 771 cm-1) aqueous silica species. The relative intensities of these two bands as a function of isochoric heating place constraints on the energetics of the polymerization reaction, if we assume that the intensity ratio is linearly related to concentration ratio. We have been able to perform experiments along two different isochores (0.9 and 0.75 g/cm3, respectively) from which we are able to derive the enthalpy of reaction.

  7. Gas Separation through Bilayer Silica, the Thinnest Possible Silica Membrane.

    Science.gov (United States)

    Yao, Bowen; Mandrà, Salvatore; Curry, John O; Shaikhutdinov, Shamil; Freund, Hans-Joachim; Schrier, Joshua

    2017-12-13

    Membrane-based gas separation processes can address key challenges in energy and environment, but for many applications the permeance and selectivity of bulk membranes is insufficient for economical use. Theory and experiment indicate that permeance and selectivity can be increased by using two-dimensional materials with subnanometer pores as membranes. Motivated by experiments showing selective permeation of H 2 /CO mixtures through amorphous silica bilayers, here we perform a theoretical study of gas separation through silica bilayers. Using density functional theory calculations, we obtain geometries of crystalline free-standing silica bilayers (comprised of six-membered rings), as well as the seven-, eight-, and nine-membered rings that are observed in glassy silica bilayers, which arise due to Stone-Wales defects and vacancies. We then compute the potential energy barriers for gas passage through these various pore types for He, Ne, Ar, Kr, H 2 , N 2 , CO, and CO 2 gases, and use the data to assess their capability for selective gas separation. Our calculations indicate that crystalline bilayer silica, which is less than a nanometer thick, can be a high-selectivity and high-permeance membrane material for 3 He/ 4 He, He/natural gas, and H 2 /CO separations.

  8. A novel approach for preparation and in situ tensile testing of silica glass membranes in the TEM

    Science.gov (United States)

    Mačković, Mirza; Przybilla, Thomas; Dieker, Christel; Herre, Patrick; Romeis, Stefan; Stara, Hana; Schrenker, Nadine; Peukert, Wolfgang; Spiecker, Erdmann

    2017-04-01

    The mechanical behavior of glasses in the micro- and/or nanometer regime increasingly gains importance in nowadays modern technology. However, suitable small scale preparation and mechanical testing approaches for a reliable assessment of the mechanical properties of glasses still remain a big challenge. In the present work, a novel approach for site-specific preparation and quantitative in situ tensile testing of thin silica glass membranes in the transmission electron microscope is presented. Thereby, advanced focused ion beam techniques are used for the preparation of nanoscale dog bone shaped silica glass specimens suitable for in situ tensile testing. Small amounts of gallium are detected on the surface of the membranes resulting from redeposition effects during the focused ion beam preparation procedure. Possible structural changes of silica glass upon irradiation with electrons and gallium ions are investigated by controlled irradiation experiments, followed by a structural analysis using Raman spectroscopy. While moderate electron beam irradiation does not alter the structure of silica glass, ion beam irradiation results in minor densification of the silica glass membranes. In situ tensile testing of membranes under electron beam irradiation results in distinctive elongations without fracture confirming the phenomenon of superplasticity. In contrast, in situ tensile testing in the absence of the electron beam reveals an elastic/plastic deformation behavior, and finally leads to fracture of the membranes. The Young’s moduli of the glass membranes pulled at beam off conditions in the TEM are comparable with values known for bulk fused silica, while the tensile strength is in the range of values reported for silica glass fibers with comparable dimensions. The impact of electron beam irradiation on the mechanical properties of silica glass membranes is further discussed. The results of the present work open new avenues for dedicated preparation and

  9. Analysis of silica fume produced by zircon desilication.

    Science.gov (United States)

    Phillips, D N; Carter, J

    2003-07-27

    Novel chemical methods have been developed to allow for the determination of the components of silica fume produced by zircon desilication. Hitherto, no methods have been described for the analysis of this material. The amorphous silica is first removed by treatment with sodium hydroxide. The residue from the hydroxide treatment may then be subjected to a suite of reagents to determine the zircon, the total zirconia, the monoclinic zirconia and the tetragonal zirconia content of the fume. The zircon content of the fume is determined by treatment of the hydroxide residue with concentrated hydrofluoric acid (HF). The total zirconia content of the fume is determined by digestion of the hydroxide residue with fuming sulphuric acid (oleum), while the relative amounts of monoclinic and tetragonal zirconia may be found by treatment of the hydroxide residue with 10%w/v HF, which attacks the less stable tetragonal phase. Both X-ray diffraction and particle size analysis were used to validate the steps in the analytical procedure. An explanation of the presence of tetragonal zirconia in the fume is proposed. A greater understanding of the composition of the fume led to the installation of a separator in the company's production line to remove the zircon. Australian Fused Materials (AFM) now produces a vastly superior grade of fume marketed under the code SF-98.

  10. Simulation of Peptide Binding to Silica and Silica Mineralization

    Science.gov (United States)

    Emami, F. S.; Heinz, H.; Berry, R. J.; Varshney, V.; Farmer, B. L.; Naik, R. R.; Patwardhan, S. V.; Perry, C. C.

    2009-03-01

    The purpose of this study is to identify the nature of the interaction of peptides with silica surfaces and their effect on mineralization. Classical force fields (CVFF, PCFF) have been extended for silica aiming at the computation of surface properties in quantitative agreement with experiment, taking explicitly into account water molecules, pH, and surface coverage with peptides. We focus on the interaction of five short peptides (pep1, pep4, 82-4, H4, R5) identified by biopanning with regular and amorphous silica surfaces (Q3 and Q2) to understand the relation between peptide sequence and affinity to the surface. Results of the atomistic molecular dynamics simulation indicate adsorption energies, binding constants and conformational changes upon adsorption. The comparison of NMR chemical shifts in solution and on the surface in computation and experiment further aids in understanding the mechanism of binding.

  11. Fabrication of 3D electro-thermal micro actuators in silica glass by femtosecond laser wet etch and microsolidics

    Science.gov (United States)

    Li, Qichao; Shan, Chao; Yang, Qing; Chen, Feng; Bian, Hao; Hou, Xun

    2017-02-01

    This paper demonstrates a novel electro-thermal micro actuator's design, fabrication and device tests which combine microfluidic technology and microsolidics process. A three-dimensional solenoid microchannel with high aspect ratio is fabricated inside the silica glass by an improved femtosecond laser wet etch (FLWE) technology, and the diameter of the spiral coil is only 200 μm. Molten alloy (Bi/In/Sn/Pb) with high melting point is injected into the three-dimensional solenoid microchannel inside the silica glass , then it solidifys and forms an electro-thermal micro actuator. The device is capable of achieving precise temperature control and quick response, and can also be easily integrated into MEMS, sensors and `lab on a chip' (LOC) platform inside the fused silica substrate.

  12. The Evaluation of Efficiency of Polish Agriculture

    Directory of Open Access Journals (Sweden)

    Piotr Bórawski

    2015-01-01

    Full Text Available The objective of the paper was to recognize the efficiency of Polish agriculture. We have studied data from Main Statistical Office (MSO and compared the efficiency in the years 2000–2010. The data proved that the efficiency of Polish agriculture improved in the analyzed period. To measure the impact of macroeconomic variables we introduced these into the regression model. The macroeconomic factors included: X1 (nominal prices of land, X2 (land prices expressed in dt, X3 (inflation, X4 (investment in agriculture and hunting, X5 (balance of trade and X6 (GDP. We wanted to recognize the impact of macroeconomic factors on: Y1 (gross output, Y2 (intermediate consumption, Y3 (gross value added. Multiple regression was used to measure the impact of macroeconomic factors on global production of agriculture. The strongest impact on gross value added had: X4 (investment in agriculture and horticulture and X4 (trade balance. Poland is a member of European Union and the Common Agricultural Policy has improved the situation in agriculture. There are about 2 100 000 farms in Poland but only 300 000–400 000 are producing for the market. Other farms have social functions and are place for work for rural inhabitants.

  13. Food patterns of Polish older people

    DEFF Research Database (Denmark)

    Wadolowska, L.; Danowska-Oziewicz, M.; Niedzwiedzka, E.

    2006-01-01

    Food patterns of Polish older people were separated and described. The research included 422 people aged 65+ years, living in 5 geographical locations. Participants of the study were selected in quota sampling. Criteria for recruitment included sex, age (65-^74 or 75+ years) and family status (li...... and small number of products fonning joint food patterns speak in advocacy of relatively small reciprocal relationship between different food items consumed by the seniors in Poland.......Food patterns of Polish older people were separated and described. The research included 422 people aged 65+ years, living in 5 geographical locations. Participants of the study were selected in quota sampling. Criteria for recruitment included sex, age (65-^74 or 75+ years) and family status...... (living alone or living with other people). Respondents were asked questions about consumption of 55 food products. The factor analysis allowed for separating 21 food patterns. They included from 1 to 3 groups of products, intake of which was mutually dependant. Big number of separated food patterns...

  14. Farmers' pensions and the Polish economic crisis.

    Science.gov (United States)

    Simanis, J G

    1983-04-01

    The Polish Government, in 1977, inaugurated a new pension program that made old-age and invalidity benefits available for the first time to most farmers in that country. The evolution and eventual failure of that program were closely intertwined with a growing national economic crisis, manifested in widespread popular unrest and culminating in emergence of the Solidarity movement. The farmers' pension program was originally presented as both a social security measure and a vehicle for improving agricultural efficiency. The economic situation was expected to benefit as farms of older owners were passed to younger, presumably more efficient, successors, with the state sometimes acting as intermediary. A further step to bind the social security concept to agricultural efficiency came through relating the pension amount to the quantity of produce the individual farmer sold to the state over a number of years. The failure of these provisions and other unpopular features of the new program was aggravated by inflation and continuing deterioration of the Polish economy.

  15. Robotic Automation in Computer Controlled Polishing

    Science.gov (United States)

    Walker, D. D.; Yu, G.; Bibby, M.; Dunn, C.; Li, H.; Wu, Y.; Zheng, X.; Zhang, P.

    2016-02-01

    We first present a Case Study - the manufacture of 1.4 m prototype mirror-segments for the European Extremely Large Telescope, undertaken by the National Facility for Ultra Precision Surfaces, at the OpTIC facility operated by Glyndwr University. Scale-up to serial-manufacture demands delivery of a 1.4 m off-axis aspheric hexagonal segment with surface precision use of robots to automate currently-manual operations on CNC polishing machines, to improve work-throughput, mitigate risk of damage to parts, and reduce dependence on highly-skilled staff. Second is the use of robots to pre-process surfaces prior to CNC polishing, to reduce total process time. The third draws the threads together, describing our vision of the automated manufacturing cell, where the operator interacts at cell rather than machine level. This promises to deliver a step-change in end-to-end manufacturing times and costs, compared with either platform used on its own or, indeed, the state-of-the-art used elsewhere.

  16. Pumping Iron and Silica Bodybuilding

    Science.gov (United States)

    Mcnair, H.; Brzezinski, M. A.; Krause, J. W.; Parker, C.; Brown, M.; Coale, T.; Bruland, K. W.

    2016-02-01

    The availability of dissolved iron influences the stoichiometry of nutrient uptake by diatoms. Under nutrient replete conditions diatoms consume silicic acid and nitrate in a 1:1 ratio, this ratio increases under iron stress. Using the tracers 32Si and PDMPO, the total community and group-specific silica production rates were measured along a gradient of dissolved iron in an upwelling plume off the California coast. At each station, a control (ambient silicic acid) and +20 µM silicic acid treatment were conducted with each tracer to determine whether silicic acid limitation controlled the rate of silica production. Dissolved iron was 1.3 nmol kg-1 nearshore and decreased to 0.15 nmol kg-1 offshore. Silicic acid decreased more rapidly than nitrate, it was nearly 9 µM higher in the nearshore and 7 µM lower than nitrate in the middle of the transect where the iron concentration had decreased. The rate of diatom silica production decreased in tandem with silicic acid concentration, and silica production limitation by low silicic acid was most pronounced when iron concentrations were >0.4 nmol kg-1. The composition of the diatom assemblage shifted from Chaetoceros spp. dominated nearshore to a more sparse pennate-dominated assemblage offshore. Changes in taxa-specific silica production rates will be reported based on examination of PDMPO labeled cells using confocal microscopy.

  17. Analytic tendencies in modern Polish and Russian

    Directory of Open Access Journals (Sweden)

    Wojciech Sosnowski

    2015-11-01

    Full Text Available Analytic tendencies in modern Polish and Russian Modern Polish and Russian are characterized by some features which demonstrate an increasing level of analitism. In the process of transformation from synthetic to analytical language, a crucial role is played by prepositional units. In this research, analitism is understood in a traditional way as a morphological and syntactic phenomenon. The fact that the synthetic structure of a language may, in some conditions, turn into an analytical one, as happened in the case of Bulgarian and Macedonian, has been intriguing linguists ever since, and has made me attempt to answer the question: What is the condition of modern Polish and Russian, which are languages with a rich literary tradition and solid grammatical norms, which belong to a group of synthetic languages? The analytical tendencies in morphology include the following: a decrease in the number of cases in all inflected parts of speech; a more frequent use of uninflected nouns and adjectives; the growing importance of nouns with common gender, and, in particular, the use of forms of masculine gender to depict feminine gender; differences in expressing collectiveness in a group of nouns (using collective meaning for forms that have singular meaning; substituting case forms with prepositions; substituting case forms with subordinate clauses; substituting case forms with “helper” words. Analytical tendencies in the area of numeral functioning include: substituting inflected forms of ordinal numerals with cardinal ones; the gradual disappearing inflection of numerals; confusing the forms of noun cases after numerals; the disappearing declination of collective numerals; displacing other cases with so-called simple cases; changing the syntactical position which the numeral should be inflected in; abandoning the declination of first elements of collective numerals. During the study of analytic tendencies in morphology, it was necessary to examine

  18. Global Citizenship Education in School Curricula. A Polish Perspective

    Science.gov (United States)

    Leek, Joanna

    2016-01-01

    The purpose of this study is to present global citizenship education from a Polish perspective. Analyzing the issue, the first part of this paper presents the development of citizenship education, followed by the current status of global citizenship education in Polish schools. In the second part of the study I draw attention to national curricula…

  19. Comparative study of performance of shoe polishes formulated from ...

    African Journals Online (AJOL)

    Polyethylene pigment was generated from “pure water sachets” (one of the major environmental nuisance today) and used in the formulation of shoe polish using paraffin wax, white spirit, turpentine oil, and nitrocellulose. The polish was found to exhibit similar wrinkle resistance, inferior gloss, rub resistance; resistance to ...

  20. Polish anthropology on the eve of the new millennium

    OpenAIRE

    Drozdowski, Zbigniew

    1999-01-01

    Author summarizes the main achievements of Polish anthropology in the 20th century, presents the main research problems of this discipline in contemporary Poland and points at the potential dangers which may be faced by Polish anthropology in the forthcoming years.

  1. Influence of melt treatments and polished CVD diamond coated ...

    Indian Academy of Sciences (India)

    Performances of the turning inserts (uncoated and polished CVD diamond coated) were evaluated in machining Al–7Si and Al–7Si–2.5Cu cast alloys under dry environment using a lathe. The polished CVD diamond coated insert outperformed the uncoated cutting insert which suffered from sizeable edge buildup leading to ...

  2. Social Obstacles Towards Success of Pupils in Polish Primary Schools.

    Science.gov (United States)

    Nakielska, Zofia

    In 1973, the Polish Minister of Education ordered objective competitions at the primary school level in the fields of Polish studies, Russian language, and math. In order to determine whether such subject competitions were justified and if they contributed equally to the development of interests and abilities among the rural and urban and…

  3. Etymology in the Polish Academy of Sciences Great Dictionary of ...

    African Journals Online (AJOL)

    The article offers an insight into etymological information provided in the Polish Academy of Sciences Great Dictionary of Polish (Pol. Wielki słownik języka polskiego PAN, WSJP PAN). The dictionary and the rules of producing the entries are briefly presented. These rules influence the way of working on etymology within ...

  4. The Czechoslovak-Polish Club in Brno (1925–1939)

    Czech Academy of Sciences Publication Activity Database

    Baron, Roman

    2011-01-01

    Roč. 3, č. 1 (2011), s. 43-64 ISSN 1803-6546 Institutional research plan: CEZ:AV0Z80150510 Keywords : Czechoslovak-Polish solidarity * Czechoslovak-Polish relations * Brno * associations * Interwar Period Subject RIV: AB - History

  5. Silica Aerogel: Synthesis and Applications

    Directory of Open Access Journals (Sweden)

    Jyoti L. Gurav

    2010-01-01

    Full Text Available Silica aerogels have drawn a lot of interest both in science and technology because of their low bulk density (up to 95% of their volume is air, hydrophobicity, low thermal conductivity, high surface area, and optical transparency. Aerogels are synthesized from molecular precursors by sol-gel processing. Special drying techniques must be applied to replace the pore liquid with air while maintaining the solid network. Supercritical drying is most common; however, recently developed methods allow removal of the liquid at atmospheric pressure after chemical modification of the inner surface of the gels, leaving only a porous silica network filled with air. Therefore, by considering the surprising properties of aerogels, the present review addresses synthesis of silica aerogels by the sol-gel method, as well as drying techniques and applications in current industrial development and scientific research.

  6. Development of silica RO membranes

    International Nuclear Information System (INIS)

    Ikeda, Ayumi; Kawamoto, Takashi; Matsuyama, Emi; Utsumi, Keisuke; Nomura, Mikihiro; Sugimoto, Masaki; Yoshikawa, Masato

    2012-01-01

    Silica based membranes have been developed by using a counter diffusion CVD method. Effects of alkyl groups in the silica precursors and deposition temperatures had investigated in order to control pore sizes of the silica membranes. In this study, this type of a silica membrane was applied for RO separation. Effects of silica sources, deposition temperatures and post treatments had been investigated. Tetramethoxysilane (TMOS), Ethyltrimethoxysilane (ETMOS) and Phenyltrimethoxysilane (PhTMOS) were used as silica precursors. A counter diffusion CVD method was carried out for 90 min at 270 - 600degC on γ-alumina capillary substrates (effective length: 50 mm, φ: 4 nm: NOK Co.). O 3 or O 2 was introduced into the inside of the substrate at the O 2 rate of 0.2 L min -1 . Ion beam irradiation was carried out for a post treatment using Os at 490 MeV for 1.0 x 10 10 ions cm -2 or 3.0 x 10 10 ions cm -2 . Single gas permeance was measured by using H 2 , N 2 and SF 6 . RO tests were employed at 3.0 or 5.4 MPa for 100 mg L -1 of feed NaCl solution. First, effects of the silica sources were investigated. The total fluxes increased by increasing N 2 permeance through the silica membrane deposited by ETMOS. The maximum NaCl rejection was 28.2% at 12.2 kg m -2 h -1 of the total flux through the membrane deposited at 270degC. N 2 permeance was 9.6 x 10 -9 mol m -2 s -1 Pa -1 . While, total fluxes through the membrane deposited by using PhTMOS were smaller than those through the ETMOS membranes. The phenyl groups for the PhTMOS membrane must be important for the hydrophobic properties through the membrane. Next, effects of ion beam irradiation were tested for the TMOS membranes. Water is difficult to permeate through the TMOS membranes due to the low N 2 permeance through the membrane (3.1 x 10 -11 mol m -2 s -1 Pa -1 ). N 2 permeance increased to 7.3 x 10 -9 mol m -2 s -1 Pa -1 by the irradiation. Irradiation amounts had little effects on N 2 permeance. However, NaCl rejections

  7. Synthesis of colloidal silica dumbbells.

    Science.gov (United States)

    Johnson, Patrick M; van Kats, Carlos M; van Blaaderen, Alfons

    2005-11-22

    We describe the synthesis and characterization of stable suspensions of monodisperse fluorescently labeled silica dumbbell particles. Pure dispersions of silica dumbbells with center-to-center lengths from 174 nm to 2.3 microm were produced with a variety of aspect ratios. Individual particles in concentrated dispersions of these particles could be imaged with confocal microscopy. These particles can be used as a colloidal model system for addressing fundamental questions about crystal and glass formation of low-aspect-ratio anisotropic particles. They also have potential in photonic applications and electro-optical devices.

  8. Niobia-silica and silica membranes for gas separation

    NARCIS (Netherlands)

    Boffa, V.

    2008-01-01

    This thesis describes the development of ceramic membranes suitable for hydrogen separation and CO2 recovery from gaseous streams. The research work was focused on the three different parts of which gas selective ceramic membranes are composed, i.e., the microporous gas selective silica layer, the

  9. Ferrocene-fused derivatives of acenes, tropones and thiepins

    Science.gov (United States)

    Maharjan, Bidhya Laxmi

    This research project is concentrated on tuning the properties of small organic molecules, namely polyacenes, tropones and thiepins, by incorporating redox-active transition metal centers pi-bonded to terminal cyclopentadienyl ligands. Organometallicfused acenequinones, tropones, thiepins and cyclopentadiene-capped polyacenes were synthesized and characterized. This work was divided into three parts: first, the synthesis of ferrocene-fused acenequinones, cyclopentadiene-capped acenequinones and their subsequent aromatization to polyacenes; second, the synthesis of ferrocene-fused tropones, thiotropones and tropone oxime; and third, the synthesis of ferrocene-fused thiepins. Ferrocene-fused quinones are the precursors to our target complexes. Our synthetic route to ferrocenequinones involved two-fold aldol condensation between 1,2- diformylferrocene and naphthalene-1,4-diol or anthracene-1,4-diol, and four-fold condensation between 1,2-diformylferrocene and 1,4-cyclohexanedione. Reduction of ferrocene-fused quinones with borane in THF resulted in ferrocene-fused dihydroacenes. Attempts to reduce ferrocene-fused acenequinones with sodium dithionite led to metalfree cyclopentadiene- (Cp-) capped acenequinones. Cp-capped acenequinones were aromatized to bis(triisopropylsilyl)ethynyl polyacenes by using lithium (triisopropylsilyl)acetylide (TIPSC≡CLi) with subsequent dehydroxylation by stannous chloride. The compounds were characterized by using spectroscopic methods and X-ray crystallography. Further, the electronic properties of these compounds were studied by using cyclic voltammetry and UV-visible spectroscopy. Cyclic voltammetry showed oxidation potentials of Cp-capped TIPS-tetracene and bis-Cp-capped TIPS-anthracene as 0.49 V and 0.61 V, respectively (vs. ferrocene/ferrocenium). The electrochemical band gaps were 2.15 eV and 2.58 eV, respectively. Organic thin-film transistor device performance of Cp-capped polyacenes was studied using solution deposition

  10. High-performance light-emitting diodes encapsulated with silica-filled epoxy materials.

    Science.gov (United States)

    Li, Tian; Zhang, Jie; Wang, Huiping; Hu, Zhongnan; Yu, Yingfeng

    2013-09-25

    Packaging materials have a great impact on the performance and reliability of light-emitting diodes (LEDs). In this study, we have prepared high performance LED devices through encapsulating LEDs by epoxy materials incorporated with filler powders. A set of evaluation methods have also been established to characterize the reliability of LED devices. No delamination or internal cracking between packaging materials and lead frames has been found for the encapsulated high performance LED devices after the package saturation with moisture and subsequent exposure to high-temperature solder reflow and thermal cycling. Four kinds of inorganic silica fillers, namely, quartz, fused silica, cristobalite, and spherical silica, and one kind of organic filler, that is, spherical silicone powder, were incorporated into the epoxy packaging materials to compare their effects on performance of LED devices. The properties of epoxy packaging materials and LED devices were studied by differential scanning calorimetry (DSC), thermogravimetric analyses (TGA), dynamic mechanical analysis (DMA), thermomechanical analyzer (TMA), ultravioletvisible spectrophotometer (UV-vis), scanning acoustic microscopy (SAM), and scanning electron microscopy (SEM). Except the spherical silicone powder filled epoxy materials, all the other filled systems showed lower equilibrium water sorption content and smaller water diffusion coefficient in both water sorption and moisture sorption tests. The coefficient of thermal expansion (CTE) values were also decreased with the addition of fillers, and the systems filled with quartz, fused, and filled with spherical silica gave the best performance, which exhibited the reduced CTE values both below and above Tg. The results of TGA essentially showed no difference between filled and unfilled systems. The glass transition temperature changed little for all the filled systems, except the one incorporated with spherical silicone. The modulus at room temperature

  11. Structure of silica-supported catalysts

    International Nuclear Information System (INIS)

    Gladden, L.F.; Vignaux, M.; Griffiths, R.W.; Jackson, S.D.; Jones, J.R.; Sharratt, A.P.; Robertson, F.J.; Webb, G.

    1992-01-01

    Neutron diffraction and SANS studies of silica supported metal catalysts have indicated that more active metal:silica catalysts are produced when the silica support has a relatively high content of three-membered rings in its network structure. SANS studies also suggest that the more active catalysts possess a bimodal metal particle size distribution. (orig.)

  12. Sonochemical coating of magnetite nanoparticles with silica.

    Science.gov (United States)

    Dang, Feng; Enomoto, Naoya; Hojo, Junichi; Enpuku, Keiji

    2010-01-01

    Magnetite nanoparticles were coated with silica through the hydrolysis and condensation of tetraethyl orthosilicate (TEOS) under ultrasonic irradiation. The ultrasonic irradiation was used to prevent the agglomeration of the magnetite particles and accelerate the hydrolysis and condensation of TEOS. TEM, DLS, XRF, VSM, TG and sedimentation test were used to characterize the silica-coated magnetite particles. The dispersibility of silica-coated magnetite particles in aqueous solution was improved significantly and the agglomerate particle size was decreased to 110 nm. It was found that the agglomerate particle size of silica-coated magnetite particles was mainly decided by the coating temperature and the pH value in the silica-coating process. The weight ratio of silica in silica-coated magnetite particles was mainly decided by the pH value in the silica-coating process. The dispersibility of silica-coated magnetite particles was mainly decided by the agglomerate particle size of the suspension. The oxidation of magnetite particles in air was limited through the coated silica. The magnetism of silica-coated magnetite particles decreased slightly after silica-coating.

  13. 21 CFR 584.700 - Hydrophobic silicas.

    Science.gov (United States)

    2010-04-01

    ...) Product. Amorphous fumed hydrophobic silica or precipitated hydrophobic silica (CAS Reg. No. 68611-0944... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Hydrophobic silicas. 584.700 Section 584.700 Food... DRUGS, FEEDS, AND RELATED PRODUCTS FOOD SUBSTANCES AFFIRMED AS GENERALLY RECOGNIZED AS SAFE IN FEED AND...

  14. Anisotropic silica mesostructures for DNA encapsulation

    Indian Academy of Sciences (India)

    functionalizing the pores of silica with amine group, the amount of DNA loaded on the rods decreases which is due to a reduction in the pore size upon grafting of amine groups. Keywords. Surfactant; reverse micellar method; silica mesostructures; surface area. 1. Introduction. Amorphous silica nanoparticles are important ...

  15. Electron microscope analyses of the bio-silica basal spicule from the Monorhaphis chuni sponge.

    Science.gov (United States)

    Werner, Peter; Blumtritt, Horst; Zlotnikov, Igor; Graff, Andreas; Dauphin, Yannicke; Fratzl, Peter

    2015-08-01

    We report on a structural analysis of several basal spicules of the deep-sea silica sponge Monorhaphis chuni by electron microscope techniques supported by a precise focused ion beam (FIB) target preparation. To get a deeper understanding of the spicules length growth, we concentrated our investigation onto the apical segments of two selected spicules with apparently different growth states and studied in detail permanent and temporary growth structures in the central compact silica axial cylinder (AC) as well as the structure of the organic axial filament (AF) in its center. The new findings concern the following morphology features: (i) at the tip we could identify thin silica layers, which overgrow as a tongue-like feature the front face of the AC and completely fuse during the subsequent growth state. This basically differs from the radial growth of the surrounding lamellar zone of the spicules made of alternating silica lamellae and organic interlayers. (ii) A newly detected disturbed cylindrical zone in the central region of the AC (diameter about 30 μm) contains vertical and horizontal cavities, channels and agglomerates, which can be interpreted as permanent leftover of a formerly open axial channel, later filled by silica. (iii) The AF consists of a three-dimensional crystal-like arrangement of organic molecules and amorphous silica surrounding these molecules. Similar to an inorganic crystal, this encased protein crystal is typified by crystallographic directions, lattice planes and surface steps. The 〈001〉 growth direction is especially favored, thereby scaffolding the axial cylinders growth and consequently the spicules' morphology. Copyright © 2015 Elsevier Inc. All rights reserved.

  16. Brewing test with puffed polished rice. : Sake brewing with puffed polished rive (II)

    OpenAIRE

    家村, 芳次; 永田, 興四郎; 田端, 昇; 佐無田, 隆; 吉沢, 淑; YOSHITSUGU, IEMURA; KOSHIROU, NAGATA; NOBORU, TABATA; TAKASHI, SAMUTA; KIYOSHI, YOSHIZAWA; 菊正宗酒造株式会社; 山邑酒造株式会社; 灘五郷酒造組合; 熊本国税局鑑定官室; 国税庁醸造試験所

    1985-01-01

    Polished rice was puffed by continuous puffing equipment, then part of it was contracted under a vapor stream. These samples were used for sake brewing.Fermentation took place normally in very tested mash. Each sake produced differed slightly in alcohol concentration, nihonshudo, and acidity; they differed greatly in the content of amino acids, with that of sake made from puffed rice was lower than that of sake made from steamed rice, and that of sake made from contracted rice after puffing t...

  17. Determination of residual zirconia in the reaction product of zircon formation from zirconia and silica

    International Nuclear Information System (INIS)

    Hashiba, Minoru; Miura, Eiji; Nurishi, Yukio; Hibino, Taizo

    1978-01-01

    A new chemical method for the determination of zirconia in the reaction product of zircon formation from zirconia and silica is presented in this paper. The reaction product was fused in the temperature range between 400 0 C, and 450 0 C by ammonium sulfate (zirconia/ammonium sulfate = 1/10, weight). Zirconia was extracted by 4N H 2 SO 4 aqueous solution. After the residue was separated by filter paper containing filter pulp, it was washed by hot water thoroughly. By adding aqueous ammonia water to the combined filtrate, zirconium hydroxide was precipitated gelatinously. The precipitate was ignited in platinum crucible at 1000 0 C and the zirconia obtained was weighed. It was confirmed by the following experiments that the present method is very reliable for quantitative determination of residual zirconia. Firstly, in both zirconia and various mixtures of zircon and silica, the recovery of zirconia is about (99.6 +- 0.2)%. Secondly, the reaction for equimolar mixture of zirconia and silica was conducted at several temperatures between 1350 0 C and 1500 0 C. The quantity of residual zirconia on the way of the reaction was reasonably determined by the present method. In conclusion, the present method can be applicable for the study on the reaction mechanism of zircon formation from zirconia and silica. (auth.)

  18. Plurilingualism and polish teenage learners of english

    Directory of Open Access Journals (Sweden)

    Agnieszka Otwinowska‑Kasztelanic

    2012-01-01

    Full Text Available Using several languages has become a norm for those who want to learn and work in the European Union. However, teaching for plurilingualism is also a challenge. The present paper first clarifies the notions of plurilingualism and multilingualism, then discusses the role of crosslinguistic similarity in language learning in the case of European languages. It also shows how lexical crosslinguistic similarity can be used in teaching typologically related and unrelated languages, and discusses the key factors in noticing such similarity. The research presented reports on examining and raising language awareness of Polish‑‑ English cognate vocabulary in the case of a group of Polish teenage learners of English. It presents the results of a small‑‑ scale study in quasi‑‑ experimental design, as well as qualitative research on the learners’ opinions and attitudes. Finally, the paper presents implications for language pedagogy and focuses on the fact that awareness raising may affect the learners’ plurilingual competence.

  19. Antigenic typing Polish isolates of canine parvovirus

    Energy Technology Data Exchange (ETDEWEB)

    Mizak, B. [National Veterinary Research Institute, Pulawy (Poland); Plucienniczak, A. [Polish Academy ofd Sciences. Microbiology and Virology Center, Lodz (Poland)

    1995-12-31

    Polish strains of canine parvovirus isolated between 1982 and 1993 were examined to determine the extent to which the virus has evolved antigenically and genetically over eleven years. Two CPV isolates obtained in Warsaw in 1982 and Pulawy in 1993, were examined using monoclonal antibody typing, restriction analysis and sequencing VP-2 protein gene. Five other isolates from Warsaw and Pulawy were tested with the panel of monoclonal antibodies specific to CPV-2, CPV-2a and common for canine parvovirus, feline panleukopenia virus and milk enteritis virus. Results of the studies demonstrated that all isolates tested represented CPV-2a antigenic type. Rapid antigenic strain replacement recorded by Parrish and Senda in the U.S.A and Japan was not confirmed in Poland. (author). 30 refs, 2 tabs.

  20. Attitudes of Polish Consumers Toward Experiential Marketing

    Directory of Open Access Journals (Sweden)

    Monika Skorek

    2017-01-01

    Full Text Available Purpose: The experience economy is a concept that can be defned as a new way of perceiving the market offer of an enterprise, focusing on the customer experience. Enterprises, both in the production and service industries, are becoming similar to one another on a massive scale, which makes it increasingly diffcult to stand out. The response to this can be to offer the consumer an unforgettable experience related to a product or service provided by a company. Methodology: This study analysed the results of qualitative research on the attitudes and opinions of Polish consumers on experience marketing. Results/fndings: The results showed that participants of the study were prepared to transition from the economy based on products or services to an economy based on experiences at a moderate level. They declared a willingness to participate in experiences offered by companies but at the same time focus on the cost and utility of them

  1. Nondestructive detection system of faults in fuses using radioisotope

    International Nuclear Information System (INIS)

    Goncalves, D.

    1973-01-01

    A system is developed to show the viability of non-destructive detection of the faults of explosive safety fuses which are manufactured by Fabrica da Estrela do Ministerio do Exercito. The faults are detected by an ion-chamber based on the variation of the intensity of the beta particles that penetrate the fuse which passes through a collimator. The beta particles are emitted by Strontium-90 + Yttrium-90 encapsulated in either stainless steel or aluminum. The concept of 'bucking Voltage' is applied to differentiate electronically the signal generated by the ion-chamber. (author)

  2. Fracture of three-dimensional fuse networks with quenched disorder

    OpenAIRE

    Räisänen, V. I.; Alava, M. J.; Nieminen, Risto M.

    1998-01-01

    We study a fracture on a quasistatic time scale in a three-dimensional (3D) fuse network model with “strong” and “weak” disorder. These two cases differ noticeably in the development of the fracture. For strong disorder the damage scaling is very close to volumelike [number of broken bonds Nb∼L3/(lnL)0.3] unlike for weak disorder [Nb∼L2.4/(lnL)0.3]. With strong disorder global load sharing is only approximately valid. The size distribution of “avalanches” of broken fuses in the failure follow...

  3. Droughts in historical times in Polish territory

    Science.gov (United States)

    Limanowka, Danuta; Cebulak, Elzbieta; Pyrc, Robert; Doktor, Radoslaw

    2015-04-01

    Climate change is one of the key environmental, social and economical issues, and it is also followed by political consequences. Impact of climate conditions on countries' economy is increasingly recognized, and a lot of attention is given, both in the global scale and by the individual national governments. In years 2008-2010, at the Poland -Institute of Meteorology and Water Management-National Research Institute was realized the KLIMAT Project on Impact of climate change on environment, economy and society (changes, effects and methods of reducing them, conclusions for science, engineering practice and economic planning) No. POIG01-03-01-14-011/08. The project was financed by the European Union and Polish state budget in frame of Innovative Economy Operational Programme. A very wide range of research was carried out in the different thematic areas. One of them was "Natural disasters and internal safety of the country (civil and economical)." The problem of drought in Poland was developed in terms of meteorology and hydrology. "Proxy" Data Descriptions very often inform about dry years and seasons, hot periods without precipitation. Analysis of historical material allowed to extract the years that have experienced prolonged periods of high temperatures and rainfall shortages. Weather phenomenon defined as drought belongs to extreme events. This information was very helpful in the process of indexing and thus to restore the course and intensity of climatic elements in the past. The analysis covered the period from year 1000 to modern times. Due to the limited information from the period of 1000-1500 the authors focused primarily on the period from 1500 to 2010. Analysis of the collected material has allowed the development of a highly precise temporal structure of the possible occurrence of dry periods to Polish territory.

  4. Functionalized silica materials for electrocatalysis

    Indian Academy of Sciences (India)

    electrochemical sensors and biosensors.1–5 Templated routes to synthesize silica materials give rise to well- ordered structures with pores and interconnected chan- nels, whereas a .... 2.2 Fabrication of electrodes. An aqueous colloidal solution (0.5–1.0%) of the res- pective material was prepared together with 0.01% poly.

  5. Poling of Planar Silica Waveguides

    DEFF Research Database (Denmark)

    Arentoft, Jesper; Kristensen, Martin; Jensen, Jesper Bo

    1999-01-01

    UV-written planar silica waveguides are poled using two different poling techniques, thermal poling and UV-poling. Thermal poling induces an electro-optic coefficient of 0.067 pm/V. We also demonstrate simultaneous UV-writing and UV-poling. The induced electro-optic effect shows a linear dependence...

  6. Functionalized silica materials for electrocatalysis

    Indian Academy of Sciences (India)

    To increase the efficiency of the electrocatalytic process and to increase the electrochemical accessibility of the immobilized electrocatalysts, functionalized and non-functionalized mesoporous organo-silica (MCM41-type-materials) are used in this study. These materials possess several suitable properties to be durable ...

  7. Dedication for Safety-Related Fuses used in Class-1E Power System

    International Nuclear Information System (INIS)

    Hong, Younghee

    2014-01-01

    The safety-related fuses used in class-1E power system provide overcurrent protection for electrical system and isolate the class 1E circuit from a fault or overload condition. These days, the number of nuclear grade suppliers has been reduced. Accordingly, commercial grade, instead of safety-related, fuses are procured and used in the utilities through the dedication process. Therefore, this paper introduces the commercial grade fuse dedication process/engineering and how to assure the quality requirements with this process and engineering. The fuses used in class-1E power system are to protect overcurrent and to isolate fault. Therefore the fuse for acceptance in order to improve the quality and reliability for commercial grade fuses shall be dedicated. The fuse resistance value may be useful as an indicator of acceptance. The current carrying capacity test can change the fuse performance properties. Therefore these critical characteristics are needed for additional review and analysis with fuse manufactures

  8. Silica-Coated Liposomes for Insulin Delivery

    Directory of Open Access Journals (Sweden)

    Neelam Dwivedi

    2010-01-01

    Full Text Available Liposomes coated with silica were explored as protein delivery vehicles for their enhanced stability and improved encapsulation efficiency. Insulin was encapsulated within the fluidic phosphatidylcholine lipid vesicles by thin film hydration at pH 2.5, and layer of silica was formed above lipid bilayer by acid catalysis. The presence of silica coating and encapsulated insulin was identified using confocal and electron microscopy. The native state of insulin present in the formulation was evident from Confocal Micro-Raman spectroscopy. Silica coat enhances the stability of insulin-loaded delivery vehicles. In vivo study shows that these silica coated formulations were biologically active in reducing glucose levels.

  9. Uranium incorporation into amorphous silica.

    Science.gov (United States)

    Massey, Michael S; Lezama-Pacheco, Juan S; Nelson, Joey M; Fendorf, Scott; Maher, Kate

    2014-01-01

    High concentrations of uranium are commonly observed in naturally occurring amorphous silica (including opal) deposits, suggesting that incorporation of U into amorphous silica may represent a natural attenuation mechanism and promising strategy for U remediation. However, the stability of uranium in opaline silicates, determined in part by the binding mechanism for U, is an important factor in its long-term fate. U may bind directly to the opaline silicate matrix, or to materials such as iron (hydr)oxides that are subsequently occluded within the opal. Here, we examine the coordination environment of U within opaline silica to elucidate incorporation mechanisms. Precipitates (with and without ferrihydrite inclusions) were synthesized from U-bearing sodium metasilicate solutions, buffered at pH ∼ 5.6. Natural and synthetic solids were analyzed with X-ray absorption spectroscopy and a suite of other techniques. In synthetic amorphous silica, U was coordinated by silicate in a double corner-sharing coordination geometry (Si at ∼ 3.8-3.9 Å) and a small amount of uranyl and silicate in a bidentate, mononuclear (edge-sharing) coordination (Si at ∼ 3.1-3.2 Å, U at ∼ 3.8-3.9 Å). In iron-bearing synthetic solids, U was adsorbed to iron (hydr)oxide, but the coordination environment also contained silicate in both edge-sharing and corner-sharing coordination. Uranium local coordination in synthetic solids is similar to that of natural U-bearing opals that retain U for millions of years. The stability and extent of U incorporation into opaline and amorphous silica represents a long-term repository for U that may provide an alternative strategy for remediation of U contamination.

  10. Direct polishing of aluminum mirrors with higher quality and accuracy.

    Science.gov (United States)

    Yin, Ziqiang; Yi, Zhang

    2015-09-10

    Diamond-turned aluminum mirrors have been widely used in modern optical systems. However, the machined surfaces have characteristic periodic tool marks, which contribute to reduced optical performance by creating effects such as scattering and distortion. This paper develops a new polishing technology to polish aluminum mirrors directly to remove tool marks and improve surface quality and surface accuracy. A Taguchi experiment was used to obtain optimal polishing conditions for reducing surface roughness, and computer-controlled optical surfacing technology was employed for form correction of aluminum mirrors.

  11. Reel-to-reel substrate tape polishing system

    Energy Technology Data Exchange (ETDEWEB)

    Selvamanickam, Venkat; Gardner, Michael T.; Judd, Raymond D.; Weloth, Martin; Qiao, Yunfei

    2005-06-21

    Disclosed is a reel-to-reel single-pass mechanical polishing system (100) suitable for polishing long lengths of metal substrate tape (124) used in the manufacture of high-temperature superconductor (HTS) coated tape, including multiple instantiations of a polishing station (114) in combination with a subsequent rinsing station (116) arranged along the axis of the metal substrate tape (124) that is translating between a payout spool (110a) and a take-up spool (110b). The metal substrate tape obtains a surface smoothness that is suitable for the subsequent deposition of a buffer layer.

  12. Quality in Air transport process of LOT Polish Airlines

    Directory of Open Access Journals (Sweden)

    Robert Rozenberg

    2015-10-01

    Full Text Available This article discusses the air transport process on scheduled long-haul flights of LOT Polish Airlines. Main focus is taken on price development of these routes. The introduction consists of a brief profile characterized LOT Polish Airlines. Next chapter summarizes the air transport process on scheduled longhaul flights. The frame of article is formed by price development statistics for scheduled long-haul flights to / from Beijing of LOT Polish Airlines and two other competing companies. Conclusion contains results of analysis and puts forward proposals to streamline of the air transport process on reviewed routes.

  13. Presentation of the verbs in Bulgarian-Polish electronic dictionary

    Directory of Open Access Journals (Sweden)

    Ludmila Dimitrova

    2014-09-01

    Full Text Available Presentation of the verbs in Bulgarian-Polish electronic dictionary This paper briefly discusses the presentation of the verbs in the first electronic Bulgarian-Polish dictionary that is currently being developed under a bilateral collaboration between IMI-BAS and ISS-PAS. Special attention is given to the digital entry classifiers that describe Bulgarian and Polish verbs. Problems related to the correspondence between natural language phenomena and their presentations are discussed. Some examples illustrate the different types of dictionary entries for verbs.

  14. Profilometric analysis of root surfaces after using various polishing agents

    Directory of Open Access Journals (Sweden)

    Anjan Jana

    2016-01-01

    Full Text Available Background: Polishing is an important step in oral prophylaxis procedure which retards further accumulation of plaque on the root surfaces. Though polishing was done with various abrasive particles with different sizes over a long period of time, it was never been highlighted to evaluate the ideal polishing material and the particle size that would produce the ideal surface smoothness (Ra 5 μm are not able to produce the surface smoothness <0.2 μm. Only, submicron sized particles are able to produce the desired smoothness.

  15. Study on the influence of the rotational speed of polishing disk on material removal in aspheric surface compliant polishing

    Directory of Open Access Journals (Sweden)

    Liyong Hu

    2015-03-01

    Full Text Available When a soft polishing tool is compressed on a stiff workpiece of curved surface, the contact area is a piece of the curved surface. In the process of aspheric surface polishing, the machining speed is always provided by the rotational speed of the spindle of a computer numerical control lathe. Yet, the polishing tool is usually made rotating to remove cutting scraps and broken abrasives from the contact area. The rotational speed of the polishing tool would change the distribution state of the relative speed in the whole contact area, and it would definitely change the volume of material removal in the surface of the workpiece. This article studies how the rotational speed of the polishing tool changes the distribution state of the relative speed in the whole contact area and material removal in the volume of the surface of the workpiece. The computing results show that the volume of material removal increases with the increase in both the rotational speed of polishing disk and the rotational speed of lathe spindle, but the polishing quality is totally not in this case.

  16. Evaluation of a color fused dual-band NVG

    NARCIS (Netherlands)

    Hogervorst, M.A.; Toet, A.

    2009-01-01

    We have tested a prototype dual-band NVG system consisting of two NVGs fitted with filters that split the NVG sensitive range into a short (visual) and a long wavelength (NIR) band. The Color-the-night technique (see Hogervorst & Toet, SPIE D&S ‘08) was used to fuse the images of the two sensors. We

  17. The burning fuse model of unbecoming in time

    Science.gov (United States)

    Norton, John D.

    2015-11-01

    In the burning fuse model of unbecoming in time, the future is real and the past is unreal. It is used to motivate the idea that there is something unbecoming in the present literature on the metaphysics of time: its focus is merely the assigning of a label "real."

  18. Synthesis of the Benzo-fused Indolizidine Alkaloid Mimics

    Directory of Open Access Journals (Sweden)

    Higuchi Kazuhiro

    2007-11-01

    Full Text Available Abstract A general synthesis of various benzo-fused indolizidine alkaloid mimics has been developed. The indolizidine derivatives 8 were prepared via heteroaryl Grignard addition to N-acylpyridinium salts followed by an intramolecular Heck cyclization. Further substitution reactions were developed to demonstrate that heterocycles 8 are good scaffolds for chemical library preparation.

  19. 29 CFR 1926.907 - Use of safety fuse.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 8 2010-07-01 2010-07-01 false Use of safety fuse. 1926.907 Section 1926.907 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR (CONTINUED) SAFETY AND HEALTH REGULATIONS FOR CONSTRUCTION Blasting and the Use of Explosives § 1926.907 Use...

  20. 49 CFR 173.184 - Highway or rail fusee.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Highway or rail fusee. 173.184 Section 173.184 Transportation Other Regulations Relating to Transportation PIPELINE AND HAZARDOUS MATERIALS SAFETY... SHIPMENTS AND PACKAGINGS Non-bulk Packaging for Hazardous Materials Other Than Class 1 and Class 7 § 173.184...

  1. A rare association of crossed fused renal ectopia

    Directory of Open Access Journals (Sweden)

    Ahmad Riaz

    2007-03-01

    Full Text Available Abstract Background Thrombocytopenia and absent radius syndrome (TAR is a rare genetic disorder. It is an autosomal recessive disorder characterised by radial aplasia and thrombocytopenia that may have additional anomalies. We report a case of TAR syndrome with crossed fused renal ectopia. This anomaly has not been previously reported in association with TAR syndrome. Case presentation A 24 years old female with Thrombocytopenia and absent radius syndrome admitted with pelvic fracture was investigated for recurrent urinary tract infections. Abdominal ultrasonography could not visualise the kidney on right side. Further extensive investigations in the form of intravenous urography (IVU, Magnetic resonance imaging (MRI and renal isotope scans revealed a crossed fused renal ectopia. Conclusion This report describes the new finding of a crossed fused renal ectopia associated with TAR syndrome that has not been reported before in the literature. Ectopic kidneys have increased susceptibility to develop complications like urinary infections, urolithiasis, and abdominal mass. There is a reported case of TAR syndrome with renal anomaly that developed Wilm's tumor. Finding of crossed fused renal ectopia warrants complete urologic investigation to rule out surgically correctable pathology in the urinary tract.

  2. Enantioselective organocatalytic partial transfer hydrogenation of lactone-fused quinolines.

    Science.gov (United States)

    Aillerie, Alexandre; de Talancé, Vincent Lemau; Moncomble, Aurélien; Bousquet, Till; Pélinski, Lydie

    2014-06-06

    The first enantioselective synthesis of 4-aza-podophyllotoxin derivatives by partial transfer hydrogenation of lactone-fused quinolines was achieved using a chiral Brønsted acid catalyst. This reaction was extended to a large scope of substrates with good yields and enantioselectivities.

  3. A Review of Variable Slicing in Fused Deposition Modeling

    Science.gov (United States)

    Nadiyapara, Hitesh Hirjibhai; Pande, Sarang

    2017-06-01

    The paper presents a literature survey in the field of fused deposition of plastic wires especially in the field of slicing and deposition using extrusion of thermoplastic wires. Various researchers working in the field of computation of deposition path have used their algorithms for variable slicing. In the study, a flowchart has also been proposed for the slicing and deposition process. The algorithm already been developed by previous researcher will be used to be implemented on the fused deposition modelling machine. To demonstrate the capabilities of the fused deposition modeling machine a case study has been taken. It uses a manipulated G-code to be fed to the fused deposition modeling machine. Two types of slicing strategies, namely uniform slicing and variable slicing have been evaluated. In the uniform slicing, the slice thickness has been used for deposition is varying from 0.1 to 0.4 mm. In the variable slicing, thickness has been varied from 0.1 in the polar region to 0.4 in the equatorial region Time required and the number of slices required to deposit a hemisphere of 20 mm diameter have been compared with that using the variable slicing.

  4. METHOD OF SEPARATING FISSION PRODUCTS FROM FUSED BISMUTH-CONTAINING URANIUM

    Science.gov (United States)

    Wiswall, R.H.

    1958-06-24

    A process is described for removing metal selectively from liquid metal compositions. The method effects separation of flssion product metals selectively from dilute solution in fused bismuth, which contains uraniunn in solution without removal of more than 1% of the uranium. The process comprises contacting the fused bismuth with a fused salt composition consisting of sodium, potassium and lithium chlorides, adding to fused bismuth and molten salt a quantity of bismuth chloride which is stoichiometrically required to convert the flssion product metals to be removed to their chlorides which are more stable in the fused salt than in the molten metal and are, therefore, preferentially taken up in the fused salt phase.

  5. Synthesis and characterization of polyimide silica hybrids

    International Nuclear Information System (INIS)

    Ullah, S.M.

    2010-01-01

    Flexible-chain polyimide (PIF) was synthesized from 4, 4'-oxydianiline (ODA) and pyromellitic dianhydride (PMDA) and the stiff-chain polyimide (PI S ) was derived from 1, 5-diaminonepthaline (DAN) and pyromellitic anhydride (PMDA). Molecular composites of polyimide were prepared by embedding the stiff-chain polyimide (PIS) in to ductile matrix of flexible-polyimide (PI F ) by blending their respective poly(amic acid) solution (20:80). Blend of rigid and flexible polyimide (20:80) was reinforced with silica up to 35 wt % by sol-gel process to form the silica reinforced molecular composite (SRMC). Silica reinforced molecular composite (SRMC) were characterized by Fourier transform infrared spectroscopy (FTIR), thermogravimetry (TG) and tensile testing (TT). FTIR results showed the shifting of Si - O - Si peak toward lower wave number with the increase in the silica wt % indicates the increase in the silica particle size. The oxidative degradation of SRMC showed an improvement of 23 degree C in composite having 30 wt% silica contents. Similarly, modulus of SRMC was increased as the concentration of silica was increased. Silica reinforced (co-)polyimide (SRCO) was prepared from the same monomers DAN, ODA and PMDA (20:80:100) and reinforced with different of silica up to 35 wt%. Comparison of thermo-mechanical properties of SRMC with SRCO was also done. Both the composite showed similar peak shift to low wave number with the increase in the wt% of silica was observed as in the case of SRMC. TG results of SRCO showed the 13 degree C improvement in the oxidative degradation with 30 wt% silica content. Tensile testing shows the 80% increase in the modulus with 35 wt% silica content. The result showed that SRMC are 15 degree C more stable than SRCO with 30 wt% silica. SRMC have 15% more modulus than SRCO with 30 wt% silica. This shows that thermo mechanical stability of SRMC's over SRCO's composites. (author)

  6. Effect of Polishing Systems on Surface Roughness and Topography of Monolithic Zirconia.

    Science.gov (United States)

    Goo, C L; Yap, Auj; Tan, Kbc; Fawzy, A S

    2016-01-01

    This study evaluated the effect of different chairside polishing systems on the surface roughness and topography of monolithic zirconia. Thirty-five monolithic zirconia specimens (Lava PLUS, 3M ESPE) were fabricated and divided into five groups of seven and polished with the following: Group 1 (WZ)-Dura white stone followed by Shofu zirconia polishing kit; Group 2 (SZ)-Shofu zirconia polishing kit; Group 3 (CE)-Ceramiste porcelain polishers; Group 4 (CM)-Ceramaster porcelain polishers; and Group 5 (KZ)-Komet ZR zirconia polishers. All specimens were ground with a fine-grit diamond bur prior to polishing procedures to simulate clinical finishing. Baseline and post-polishing profilometric readings were recorded and delta Ra values (difference in mean surface roughness before and after polishing) were computed and analyzed using one-way analysis of variance and Scheffe post hoc test (pzirconia.

  7. Polish electoral geography and its methods

    Directory of Open Access Journals (Sweden)

    Zbigniew Rykiel

    2011-01-01

    Full Text Available Differences in the understanding of electoral geography between social sciences are discussed in the article. Main fields and spatial scales of Polish electoral geography are identified. Main methods of multidimensional statistics are discussed. A necessity of a proper choice, based on theories of voting behaviour, of explaning variables to statistical models are emphasised. Regression analysis indicates only a formal usefulness in electoral geography, for quantitative relationships between variables in the model can be evidenced, which may be meaningless not only essentially, but even statistically. The application of canonical analysis in electoral geography brought a methodological turning-point to the statistical approach. This method allowed to combine: (1 the foundation of the selection of input variables on theories of voting behaviour; (2 the analysis of dependence of the electoral results on socio-economic characteristics of areas; (3 an identification of electoral options; (4 a quantification of the role of the historical heritage in the contemporary voting behaviour; and (5 the analysis of the stability of the electoral space. A well grounded opinion was weakened about the general competitiveness of right- and left-wing parties in Poland’s political space. Parties with similar rather than different programmes compete in given areas. It was indicated that elections have only formal influence on the structure of Parliament while the electoral system is decisive. Electoral, including territorial, manipulations also play their part. The empirical analysis indicated that Poland’s political space is polarised between the right-wing-oriented areas of the south-eastern half of the country and the left-wing-oriented areas of the north-western half. The political competition between the left and the right operates merely on the national scale, while it is not reflected territorially.The quantification of the influence of the nineteenth

  8. Polish Defense Policy in the Context of National Security Strategy

    Science.gov (United States)

    2006-06-01

    Antoni Podolski, Polska Strategia Bezpieczenstwa jako Praktyczna Implementacja Europejskiej Strategii Bezpeczenstwa –miedzy teoria a praktyka (Warszawa...Implementacja Europejskiej Strategii Bezpeczenstwa –miedzy teoria a praktyka (Warszawa: Center for International Relations, 2005), 13. Polish Ministry

  9. Super Polishing of Aluminum 6061-T6 Mirrors, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — An innovative 2D super-polishing process for Aluminum 6061-T6 planar mirrors which removes diamond point turning (DPT) grooves and attains rms surface finishes below...

  10. The resettlement of Polish refugees after the second world war

    Directory of Open Access Journals (Sweden)

    Agata Blaszczyk

    2017-02-01

    Full Text Available The passing of the Polish Resettlement Act and the creation of the different agencies related to it undoubtedly represented an unprecedented response to the challenge of mass migration in the UK.

  11. Production of rare earth polishing powders in Russia

    International Nuclear Information System (INIS)

    Kosynkin, V.D.; Ivanov, E.N.; Kotrekhov, V.A.; Shtutza, M.G.; Grabko, A.I.

    1998-01-01

    Full text: Russia is a potent producer of polishing powders made of rare earth material presented as an extensive and well developed base. Considering the reserves, the facilities predisposition and the polishing agent (cerium dioxide) content the chief mineral source is loparite, apatite and monazite. The production of rare earth polishing powders is based on specially developed continuous technological processes, corrosion-proof equipment, ensuring a high and stable production quality. A special attention is paid to the radiation safety of the powders. The initial material for the rare earth polishing powders based on loparite is the fusion cake of rare earth chlorides obtained at that mineral chlorination. The technology of the polishing powder production from the REE fusion cake includes the following stages: dissolution of the REE fusion cake chlorides; - thorough cleaning of the REE fusion cake chlorides from radioactive and non-rare-earth impurities; chemical precipitation of REE carbonates, obtaining middlings with proper material and granulometric composition, thermal treatment of precipitated carbonates followed with the operations of drying and roasting; classification of roasted oxides, obtaining end products - polishing powders. The production of fluorine-containing powders includes the stage of their fluorination after the stage of carbonate precipitation. The stabilizing doping can be introduced both into the middlings during one of the technological process of powders manufacturing and into the end product. Rare earth polishing powders are manufactured in Russia by the Share Holding Company 'Chepetz Mechanical Plant' (ChMP Co.), the city of Glasov. The plant produces a number of polishing materials, such as; polishing powder Optinol, containing at least 50% by mass of cerium dioxide, used in the mass production of optical and other articles; polishing powder Optinol-10 with doping to improve the sedimentary and aggregate stability of the solid phase

  12. British and American English for Polish University Students

    Science.gov (United States)

    Marton, Waldemar; Preston, Dennis R.

    1975-01-01

    This article attempts to assess the validity of dividing Polish students of English into British and American groups. The tests of the various hypotheses regarding linguistic and non-linguistic results of such divisions are described. (AM)

  13. Polish Defense Policy in the Context of National Security Strategy

    National Research Council Canada - National Science Library

    Bieniek, Piotr S

    2006-01-01

    ...) and the North Atlantic Treaty Organization (NATO). Polish security policy and strategy is shaped by its geographical location, which places Poland in NATO's main strategic area opposite the Russian Federation and Belarus...

  14. Borel hierarchies in infinite products of Polish spaces

    Indian Academy of Sciences (India)

    with two product topologies: (i) the product of copies of the Polish topology on X, so that H is again a Polish space and (ii) the product of copies of the discrete topology on X. Define now the Borel hierarchy in the larger topology on H. To do so, we need some notation. An element of H will be denoted by h = (x1,x2,...,xn,.

  15. Evaluation of the COMSOL software electro-polishing of samples

    International Nuclear Information System (INIS)

    Bruchon, M.

    2007-01-01

    The niobium electro-polishing is efficient if a viscous layer exists at the surface. In order to define parameters of samples electro-polishing, opened with difficulty to the experiments, the simulation is essential. This report presents works realized with the COMSOL software. The Nernst Planck equations have been associated to the Navier Stockes ones for an incompressible fluid. The study of the potential behaviour on the viscous layer and the mobility value have been detailed. (A.L.B.)

  16. Borel hierarchies in infinite products of Polish spaces

    Indian Academy of Sciences (India)

    E-mail: rana@isical.ac.in; maitra@stat.umn.edu. MS received 22 August 2005; revised 28 August 2006. Abstract. Let H be a product of countably infinite number of copies of an uncountable. Polish space X. Let ξ ( ξ ) be the class of Borel sets of additive class ξ for the product of copies of the discrete topology on X (the Polish ...

  17. Stem subsidence of polished and rough double-taper stems

    Science.gov (United States)

    Yamada, Kengo; Hirosaki, Kenichi; Takano, Masahiro; Matsumoto, Tadami

    2009-01-01

    Background and purpose Many clinical reports have indicated that polished hip stems show better clinical results than rough stems of the same geometry. It is still unknown, however, what the mechanical effects are of different surface finishes on the cement at the cement-bone interface. We compared mechanical effects in an in vitro cemented hip arthroplasty model. Methods Two sizes of double-taper polished stems and matt-processed polished stems (rough stems) were fixed into composite femurs. A 1-Hz dynamic load was applied to the stems for 1 million cycles. An 8-h no-load period was set after every 16 h of load. Stem subsidence within the cement, and compressive force and horizontal cement creep at the cement-bone interface, were measured. Results Compared to rough stems, stem subsidence, compressive force and cement creep for polished stems were a maximum of 4, 12, and 7-fold greater, respectively. There was a strong positive correlation between stem subsidence and compressive force for polished stems. In contrast, a strong negative correlation was found between stem subsidence and compressive force for rough stems. There was also a statistically significant relationship between compressive force on the cement and cement creep for the polished stems, but no significant relationship was found for rough stems. Interpretation This is the first evidence that different surface finishes of stems can have different mechanical effects on the cement at the cement-bone interface. Stem subsidence in polished stems resulted in compressive force on the cement and cement creep. The mechanical effects that polished taper stems impart on cement at the cement-bone interface probably contribute to their good long-term fixation and excellent clinical outcome. PMID:19421909

  18. Lexical exponents of hypothetical modality in Polish and Lithuanian

    OpenAIRE

    Roman Roszko

    2015-01-01

    Lexical exponents of hypothetical modality in Polish and Lithuanian The article focuses on the lexical exponents of hypothetical modality in Polish and Lithuanian. The purpose for comparing and contrasting the lexical exponents of hypothetical modality is not only to identify all the lexemes in both languages but also find the answer to the following question: whether the morphological exponents of hypothetical modality (so-called modus relativus) familiar to the Lithuanian language have/...

  19. Reusing Ceramic Tile Polishing Waste In Paving Block Manufacturing

    OpenAIRE

    Giordano Penteado; Carmenlucia Santos; de Carvalho; Eduardo Viviani; Cecche Lintz; Rosa Cristina

    2016-01-01

    Ceramic companies worldwide produce large amounts of polishing tile waste, which are piled up in the open air or disposed of in landfills. These wastes have such characteristics that make them potential substitutes for cement and sand in the manufacturing of concrete products. This paper investigates the use of ceramic tile polishing waste as a partial substitute for cement and sand in the manufacturer of concrete paving blocks. A concrete mix design was defined and then the sand was replaced...

  20. Color stability of nanocomposites polished with one-step systems.

    Science.gov (United States)

    Ergücü, Zeynep; Türkün, L Sebnem; Aladag, Akin

    2008-01-01

    This study compared the color changes of five novel resin composites polished with two one-step polishing systems when exposed to coffee solution. The resin composites tested were Filtek Supreme XT, Grandio, CeramX, Premise and Tetric EvoCeram. A total of 150 discs (30/resin composites, 10 x 2 mm) were fabricated. Ten specimens/resin composites cured under Mylar strips served as the control. The other samples were polished with PoGo and OptraPol discs for 30 seconds using a slow speed handpiece and immersed in coffee (Nescafé) for seven days. Color measurements were made with Vita Easyshade at baseline and after one and seven days. Repeated Measures ANOVA and Bonferroni tests were used for statistical analyses (pGrandio, there were no significant differences between the Mylar and PoGo groups, while the most stain resistant surfaces were attained with OptraPol. Removing the outermost resin layer by polishing procedures is essential to achieving a stain resistant, more esthetically stable surface. One-step polishing systems can be used successfully for polishing nanocomposites.

  1. Factors influencing the surface quality of polished tool steels

    International Nuclear Information System (INIS)

    Rebeggiani, S; Rosén, B-G

    2014-01-01

    Today’s demands on surface quality of moulds for injection moulding of plastic components involve no/low defect contents and roughness levels in the nm-range for high gloss applications. Material properties as well as operating conditions influence the mould finish, and thus the final surface of moulded products. This paper focuses on how particle content and different polishing strategies influence final surface qualities of moulds. Visual estimations of polished tool steel samples were combined with non-contact 3D-surface texture analysis in order to correlate traditional assessments to more quantitative methods, and to be able to analyse the surfaces at nanometre-level. It was found that steels with a lower proportion of particles, like carbides and oxides, gave rise to smoother polished surfaces. In a comparative study of polishers from different polishing shops, it was found that while different surface preparation strategies can lead to similar final roughness, similar preparation techniques can produce high-quality surfaces from different steel grades. However, the non-contact 3D-surface texture analysis showed that not all smooth polished surfaces have desirable functional topographies for injection moulding of glossy plastic components. (paper)

  2. Advanced method for the characterization of polishing suspensions

    Science.gov (United States)

    Trum, Christian J.; Sitzberger, Sebastian; Rascher, Rolf

    2017-06-01

    The industrial production of components for applications in the area of precision optics has a long-standing tradition in Germany. As in almost all branches of industry, the external circumstances, processes and products have changed over time. Large lots are becoming less frequent and the demand for special components is growing. In order to meet these requirements, it is necessary to adapt the production processes quickly and flexibly. In the field of chemo-mechanical polishing (CMP), this means that in addition to the process parameters such as speed, pressure and feed, the task-specific adaptation of suspension and polishing pad carriers gain in importance. Along with these changes, it is becoming increasingly important to compare and evaluate the properties of the various polishing suspensions. The procedures according to DIN 58750-3 and DIN 58750-4 are suitable for this purpose. Due to the clearly defined procedures and the constant boundary conditions, different suspensions can be compared and evaluated. The study presented here shows that this method can also lead to misinterpretations. Known relationships, such as the influence of the polishing pad, the concentration of the suspension and the influence of the processed materials play an important role. An extension of the procedure of DIN 58750-3 for the test of a polishing agent can help in a task-specific characterization of polishing slurries.

  3. Polish university as an (unattractive potential employer

    Directory of Open Access Journals (Sweden)

    Baruk, Agnieszka Izabela

    2017-12-01

    Full Text Available The article presents issues associated with the reasons for the fact that young potential employees are not interested in starting work at Polish universities. The article is theoretical-empirical in character. The theoretical part highlights the importance of a situation in which an entity is regarded as an attractive employer, which allows attracting the best employees. Particular attention is paid to the fact that a university needs to build its image as an employer, which results from its characteristics. The article strives to achieve three research goals, among others, identifying the reasons why respondents are not interested in starting work at a university and arranging these reasons hierarchically. Two research hypotheses were subject to preliminary verification: H1 – the main reason for the unwillingness to start work at a university are financial aspects; H2 – the main reason for the unwillingness to start work at a university are the aspects of prestige. The data collected in course of primary research were subject to quantitative analysis based on the method of average assessment analysis and the method of factor analysis. Their results show that the respondents were not interested in work at a university mainly because they wanted to test the knowledge and skills acquired during studies in other branches. At the same time, the aspects of finances and prestige didn’t play a major role. Thus, in case of the surveyed sample of respondents both research hypotheses have to be recognized as untrue.

  4. ECOLOGICAL IDEAS IN POLISH ARCHITECTURE - ENVIRONMENTAL IMPACT

    Directory of Open Access Journals (Sweden)

    Magdalena SZPYTMA

    2016-06-01

    Full Text Available Solutions in the field of ecological architecture appear more and more often in Poland. There are two approaches to eco-design: high-tech and low-tech. High-tech focuses on the use of the latest technological solvings. These means are often used in newly designed commercial buildings, such as the first Polish office building which uses passive technology, built in Katowice, in Euro-Centrum Science and Technology Park. It is intended especially for companies focusing on energy observance issues. Low-tech is usually used in small-scale buildings (for example a cottage in Jartypory village, and is focused on the use of inexpensive, traditional technologies and the daily conscious management of natural resources. Thinking about the impact on the environment and principles of sustainable development is also present in urban planning. In Siewierz, near Katowice, Poland’s first eco-village is being built, with full infrastructure, high-quality residential buildings, shops, offices and hotels. The range of applied solutions will allow residents for the economical exploitation of these buildings.

  5. Thermodynamical motivation of the Polish energy policy

    Directory of Open Access Journals (Sweden)

    Ziębik Andrzej

    2013-02-01

    Full Text Available Basing on the first and second law of thermodynamics the fundamental trends in the Polish energy policy are analysed, including the aspects of environmental protection. The thermodynamical improvement of real processes (reduction of exergy losses is the main way leading to an improvement of the effectivity of energy consumption. If the exergy loss is economically not justified, we have to do with an error from the viewpoint of the second law analysis. The paper contains a thermodynamical analysis of the ratio of final and primary energy, as well as the analysis of the thermo-ecological cost and index of sustainable development concerning primary energy. Analyses of thermo-ecological costs concerning electricity and centralized heat production have been also carried out. The effect of increasing the share of high-efficiency cogeneration has been analyzed, too. Attention has been paid to an improved efficiency of the transmission and distribution of electricity, which is of special importance from the viewpoint of the second law analysis. The improvement of the energy effectivity in industry was analyzed on the example of physical recuperation, being of special importance from the point of view of exergy analysis.

  6. Personality of Polish gay men and women

    Directory of Open Access Journals (Sweden)

    Marcin Kwiatkowski

    2015-12-01

    Full Text Available Background Sexuality is a part of one’s identity and personality that is shaped under the influence of biological and environmental factors and interactions with society. The results of research conducted so far and concerning the personality traits of gay men and women are not consistent, and only a small number of them concern the Polish population. Hence the objective of the present research was to provide personality profiles of men and women with different sexual orientations. Participants and procedure The participants (N = 346 included 84 gay women, 82 gay men, 95 heterosexual women and 85 heterosexual men. The following measures were used: a survey developed by the author, the Kinsey Scale, the EPQ-R (Eysenck Personality Questionnaire Revised adapted by Brzozowski and Drwal (1995, and the Sixteen-factor Personality Questionnaire of Cattell adapted by Nowakowska (1970. Results The results support the hypothesis that gay women and heterosexual men share similar personality traits, while gay men have more diverse traits, similar to the traits typical for heterosexual women and men. In particular, personalities of gay men are described by such traits as progressive attitude, independence, or willingness to take risks, which means traits linked to factor Q1. The highest values of that factor are observable in the case of gay men, as compared to gay women, and also in comparison with heterosexual men and women. Conclusions Sexual orientation is responsible for differences in personality traits of the studied group to a greater extent than their biological sex.

  7. Marketing Globalisation – Polish Market Experience

    Directory of Open Access Journals (Sweden)

    Robert Nowacki

    2007-09-01

    Full Text Available The beginning of the 21st century has been yielded with an acceleration of transformations occurring in economies of the whole world. These changes relate to all the areas of economic life functioning. The most important manifestation thereof is a reinforcement of competitive phenomena. Among the most important reasons for such a state of affairs, there is mentioned globalisation. The course of its processes forces the organisation operating in the market to undertake adaptive actions. One of them is reorientation of marketing activities. The need to modify the previous marketing concepts results, first of all, from far reaching alterations in the sphere of consumption, just triggered by globalisationís impact. These trends are noticed in all the markets, also in the Polish one. The foreign enterprises operating in it more and more often use the concept of global marketing. This makes us to have reflection on what is the real effectiveness of such actions and what are the possibilities to form oneís competitive position owing to that. The article constitutes an attempt to provide answers to these questions.

  8. Automated visual inspection for polished stone manufacture

    Science.gov (United States)

    Smith, Melvyn L.; Smith, Lyndon N.

    2003-05-01

    Increased globalisation of the ornamental stone market has lead to increased competition and more rigorous product quality requirements. As such, there are strong motivators to introduce new, more effective, inspection technologies that will help enable stone processors to reduce costs, improve quality and improve productivity. Natural stone surfaces may contain a mixture of complex two-dimensional (2D) patterns and three-dimensional (3D) features. The challenge in terms of automated inspection is to develop systems able to reliably identify 3D topographic defects, either naturally occurring or resulting from polishing, in the presence of concomitant complex 2D stochastic colour patterns. The resulting real-time analysis of the defects may be used in adaptive process control, in order to avoid the wasteful production of defective product. An innovative approach, using structured light and based upon an adaptation of the photometric stereo method, has been pioneered and developed at UWE to isolate and characterize mixed 2D and 3D surface features. The method is able to undertake tasks considered beyond the capabilities of existing surface inspection techniques. The approach has been successfully applied to real stone samples, and a selection of experimental results is presented.

  9. Study on chemical mechanical polishing of silicon wafer with megasonic vibration assisted.

    Science.gov (United States)

    Zhai, Ke; He, Qing; Li, Liang; Ren, Yi

    2017-09-01

    Chemical mechanical polishing (CMP) is the primary method to realize the global planarization of silicon wafer. In order to improve this process, a novel method which combined megasonic vibration to assist chemical mechanical polishing (MA-CMP) is developed in this paper. A matching layer structure of polishing head was calculated and designed. Silicon wafers are polished by megasonic assisted chemical mechanical polishing and traditional chemical mechanical polishing respectively, both coarse polishing and precision polishing experiments were carried out. With the use of megasonic vibration, the surface roughness values Ra reduced from 22.260nm to 17.835nm in coarse polishing, and the material removal rate increased by approximately 15-25% for megasonic assisted chemical mechanical polishing relative to traditional chemical mechanical polishing. Average Surface roughness values Ra reduced from 0.509nm to 0.387nm in precision polishing. The results show that megasonic assisted chemical mechanical polishing is a feasible method to improve polishing efficiency and surface quality. The material removal and finishing mechanisms of megasonic vibration assisted polishing are investigated too. Copyright © 2017 Elsevier B.V. All rights reserved.

  10. Randomized clinical study of wear of enamel antagonists against polished monolithic zirconia crowns.

    Science.gov (United States)

    Esquivel-Upshaw, J F; Kim, M J; Hsu, S M; Abdulhameed, N; Jenkins, R; Neal, D; Ren, F; Clark, A E

    2018-01-01

    To test the hypothesis that there is no difference in the in vivo maximum wear of enamel opposing monolithic zirconia crowns, enamel opposing porcelain fused to metal crowns and enamel opposing enamel. Thirty patients needing single crowns were randomized to receive either a monolithic zirconia or metal-ceramic crown. Two non-restored opposing teeth in the same quadrants were identified to serve as enamel controls. After cementation, quadrants were scanned for baseline data. Polyvinylsiloxane impressions were obtained and poured in white stone. Patients were recalled at six-months and one-year for re-impression. Stone models were scanned using a tabletop laserscanner to determine maximum wear. Statistical analysis was performed using Mann-Whitney U to determine any significant differences between the wear of enamel against zirconia and metal-ceramic crowns. Sixteen zirconia and 14 metal-ceramic crowns were delivered. There were no statistical differences in mean wear of crown types (p=0.165); enamel antagonists (p=0.235) and enamel controls (p=0.843) after one year. Monolithic zirconia exhibited comparable wear of enamel compared with metal-ceramic crowns and control enamel after one year. This study is clinically significant because the use of polished monolithic zirconia demonstrated comparable wear of opposing enamel to metal-ceramic and enamel antagonists. Copyright © 2017 Elsevier Ltd. All rights reserved.

  11. Silica precipitation by synthetic minicollagens.

    Science.gov (United States)

    Weiher, Felix; Schatz, Michaela; Steinem, Claudia; Geyer, Armin

    2013-03-11

    Oligomeric Pro-Hyp-Gly- (POG-) peptides, wherein the collagenous triple helix is supported by C-terminal capping, exhibit silica precipitation properties (O, Hyp = (2S,4R)hydroxyproline). As quantified by a molybdate assay, the length of the covalently tethered triple helix (number of POG units) determines the amount of amorphous silica obtained from silicic acid solution. Although lacking charged side chains, the synthetic collagens precipitate large quantities of silicic acid resulting in micrometer-sized spheres of varying surface morphologies as analyzed by scanning electron microscopy. Similar precipitation efficiencies on a fast time scale of less than 10 min were previously described only for biogenic diatom proteins and sponge collagen, respectively, which have a considerably higher structural complexity and limited accessibility. The minicollagens described here provide an unexpected alternative to the widely used precipitation conditions, which generally depend on (poly-)amines in phosphate buffer. Collagen can form intimate connections with inorganic matter. Hence, silica-enclosed collagens have promising perspectives as composite materials.

  12. Molecular-Level Analysis of Shock-Wave Physics and Derivation of the Hugoniot Relations for Fused Silica

    Science.gov (United States)

    2012-06-01

    Cheese - man, C. Fountzoulas, P. Patel, D.W. Templeton, and K.D. Bishnoi, Multi-Length Scale Modeling of High-Pressure Induced Phase Trans- formations...Chem. B, 1998, 102, p 7338–7364 27. H. Sun, P. Ren, and J.R. Fried , The COMPASS Force Field: Parameterization and Validation for Phosphazenes, Comput

  13. Investigations of laser-induced damages in fused silica optics using x-ray laser interferometric microscopy

    Czech Academy of Sciences Publication Activity Database

    Margarone, Daniele; Rus, Bedřich; Kozlová, Michaela; Nejdl, Jaroslav; Mocek, Tomáš; Homer, Pavel; Polan, Jiří; Stupka, Michal; Cassou, K.; Kazamias, S.; Lagron, J.C.; Ros, D.; Danson, C.; Hawkes, S.

    2010-01-01

    Roč. 107, č. 10 (2010), 103103/1-103103/7 ISSN 0021-8979 R&D Projects: GA MŠk(CZ) 7E08099; GA AV ČR IAA100100911 Institutional research plan: CEZ:AV0Z10100523 Keywords : laser beam effects * light interferometry * mirrors * optical materials * optical self-focusing * optical arrays * optical beam splitters Subject RIV: BH - Optics , Masers, Lasers Impact factor: 2.064, year: 2010 http://jap.aip.org/japiau/v107/i10/p103103_s1

  14. Flow field velocity measurements for non-isothermal systems. [of chemically reactive flow inside fused silica CVD reactor vessels

    Science.gov (United States)

    Johnson, E. J.; Hyer, P. V.; Culotta, P. W.; Clark, I. O.

    1991-01-01

    Experimental techniques which can be potentially utilized to measure the gas velocity fields in nonisothermal CVD systems both in ground-based and space-based investigations are considered. The advantages and disadvantages of a three-component laser velocimetry (LV) system that was adapted specifically for quantitative determination of the mixed convective flows in a chamber for crystal growth and film formation by CVD are discussed. Data from a horizontal research CVD reactor indicate that current models for the effects of thermophoretic force are not adequate to predict the thermophoretic bias in arbitrary flow configurations. It is concluded that LV techniques are capable of characterizing the fluid dynamics of a CVD reactor at typical growth temperatures. Thermal effects are shown to dominate and stabilize the fluid dynamics of the reactor. Heating of the susceptor increases the gas velocities parallel to the face of a slanted susceptor by up to a factor of five.

  15. Comparison of the morphology of alkali–silica gel formed in limestones in concrete affected by the so-called alkali–carbonate reaction (ACR) and alkali–silica reaction (ASR)

    International Nuclear Information System (INIS)

    Grattan-Bellew, P.E.; Chan, Gordon

    2013-01-01

    The morphology of alkali–silica gel formed in dolomitic limestone affected by the so-called alkali–carbonate reaction (ACR) is compared to that formed in a siliceous limestone affected by alkali–silica reaction (ASR). The particle of dolomitic limestone was extracted from the experimental sidewalk in Kingston, Ontario, Canada that was badly cracked due to ACR. The siliceous limestone particle was extracted from a core taken from a highway structure in Quebec, affected by ASR. Both cores exhibited marked reaction rims around limestone particles. The aggregate particles were polished and given a light gold coating in preparation for examination in a scanning electron microscope. The gel in the ACR aggregate formed stringers between the calcite crystals in the matrix of the rock, whereas gel in ASR concrete formed a thick layer on top of the calcite crystals, that are of the same size as in the ACR aggregate

  16. 31 CFR 100.12 - Exchange of fused and mixed coins.

    Science.gov (United States)

    2010-07-01

    ... 31 Money and Finance: Treasury 1 2010-07-01 2010-07-01 false Exchange of fused and mixed coins... OF PAPER CURRENCY AND COIN Exchange of Coin § 100.12 Exchange of fused and mixed coins. (a) Definitions. (1) Fused coins are U.S. coins which are melted to the extent that they are bonded together and...

  17. Reliability assessment of reserved water disposal with erodible fuse plug

    Directory of Open Access Journals (Sweden)

    Kosichenko Yuriy Mikhaylovich

    Full Text Available Water disposal constructions are one of the most responsible constructions of reservoir hydrosystem, that’s why the a lot of attention was always paid to the problems of estimating and providing their reliability and safety. The most important function of such objects is providing reliability and safety of other hydraulic constructions and economic assets in afterbay and water head. The authors offer estimation method for reliability and faultless performance of reserved water disposal with erodible fuse plug on low-head water development. In order to estimate the reliability of reserved water disposal with erodible fuse plug the Bayesian treatment was used. The calculation of diagnoses (states of reserved water disposal isoffered in case of diagnostic properties k 1 and k 2. One of the main demands placed onreserved water disposals is erosion of soil plug in case of flood discharge exeedance over the estimated frequency with the full opening of the waste sluice.

  18. Silica supported nickel catalysts : Tracer studies.

    OpenAIRE

    Sharratt, Andrew Paul.

    1991-01-01

    A series of silica supported catalysts were prepared by impregnation of the support materials with a nickel(II) nitrate precursor under standard conditions. The catalysts and silicas were characterised using temperature programmed reduction (TPR) techniques, neutron diffraction, small angle neutron scattering, and 29Si magic angle spinning nuclear magnetic resonance (MAS-NMR). These analyses revealed one significant variable in the silicas:- the surface concentration of strained siloxane ring...

  19. Mesoporous Silica: A Suitable Adsorbent for Amines

    Directory of Open Access Journals (Sweden)

    Abdollahzadeh-Ghom Sara

    2009-01-01

    Full Text Available Abstract Mesoporous silica with KIT-6 structure was investigated as a preconcentrating material in chromatographic systems for ammonia and trimethylamine. Its adsorption capacity was compared to that of existing commercial materials, showing its increased adsorption power. In addition, KIT-6 mesoporous silica efficiently adsorbs both gases, while none of the employed commercial adsorbents did. This means that KIT-6 Mesoporous silica may be a good choice for integrated chromatography/gas sensing micro-devices.

  20. Effect of various polishing systems on the surface roughness and phase transformation of zirconia and the durability of the polishing systems.

    Science.gov (United States)

    Park, Chan; Vang, Mong-Sook; Park, Sang-Won; Lim, Hyun-Pil

    2017-03-01

    Although many systems are used to polish zirconia, a comparison of the performance of zirconia and feldspathic porcelain polishing systems is lacking. The purpose of this in vitro study was to compare the effects of 3 polishing systems on surface roughness, zirconia phase transformation, and durability of the polishing systems when applied to zirconia and feldspathic porcelain. Three polishing systems were evaluated: Z1, a zirconia polishing system; Z2, a zirconia polishing system, and F1, a feldspathic porcelain polishing system. Three ceramic systems were evaluated: PR and ZM zirconia specimens (diameter 15 mm, height 2 mm; 23 specimens each) and CB feldspathic porcelain specimens of the same size (15 specimens). A rough surface was created on the 3 types of specimens (15 specimens each) to model an occlusal adjustment under the same conditions. Polishing was carried out with the 3 polishing systems for 2 minutes each. Surface roughness was measured with a 3-dimensional (3D) optical profiler. The surface was also observed with a scanning electron microscopy. X-ray diffraction analysis was performed for 8 PR or ZM zirconia specimens polished by using the Z1 and Z2 systems for 8 minutes to evaluate the phase transformation of zirconia before, during, and after polishing. These specimens were compared and analyzed for phase transformation that might have occurred during the polishing of the specimens. After finishing the surface roughness experiment and the phase transformation experiment, the volumes of the polishers were measured with a 3D volume scanner and compared with those before the experiments to evaluate the durability of the polishing system. A statistical analysis of all data was performed using 2-way ANOVA and the Tukey honest significant difference test (α=.05). The 2 zirconia polishing systems (Z1, Z2) created a significantly (Pzirconia specimens for 8 minutes, the maximum percentages of monoclinic phase increased by 0.03% in the Z1 system and by 0

  1. Computer-Controlled Cylindrical Polishing Process for Development of Grazing Incidence Optics for Hard X-Ray Region

    Science.gov (United States)

    Khan, Gufran Sayeed; Gubarev, Mikhail; Speegle, Chet; Ramsey, Brian

    2010-01-01

    The presentation includes grazing incidence X-ray optics, motivation and challenges, mid spatial frequency generation in cylindrical polishing, design considerations for polishing lap, simulation studies and experimental results, future scope, and summary. Topics include current status of replication optics technology, cylindrical polishing process using large size polishing lap, non-conformance of polishin lap to the optics, development of software and polishing machine, deterministic prediction of polishing, polishing experiment under optimum conditions, and polishing experiment based on known error profile. Future plans include determination of non-uniformity in the polishing lap compliance, development of a polishing sequence based on a known error profile of the specimen, software for generating a mandrel polishing sequence, design an development of a flexible polishing lap, and computer controlled localized polishing process.

  2. Variable fused deposition modelling - concept design and tool path generation

    OpenAIRE

    Brooks, Hadley Laurence

    2011-01-01

    Current Fused Deposition Modelling (FDM) techniques use fixed diameter nozzles to deposit a filament of plastic layer by layer. The consequence is that the same small nozzle, essential for fine details, is also used to fill in relatively large volumes. In practice a Pareto-optimal nozzle diameter is chosen that attempts to maximise resolution while minimising build time. This paper introduces a concept for adapting an additive manufacturing system, which exploits a variable diameter nozzle fo...

  3. The Manufacture of Honeycomb Cores using Fused Deposition Modelling

    OpenAIRE

    Pollard, Dave; Ward, Carwyn; Herrmann, Guido; Etches, Julie

    2016-01-01

    Sandwich panels are used in many industries, for the advantageous properties of high stiffness, good strength to weight ratio, and impact resistance. Modern manufacturing methods are dominated by manual layup; secondary structure panels often contain multiple core components, complex geometries, and tight placement tolerances. This paper compares cores manufactured using Fused Deposition Modelling (FDM) with conventional Nomex core. FDM is a process of creating complex components from extrude...

  4. Testing of Materials for Rapid Prototyping Fused Deposition Modelling Technology

    OpenAIRE

    L. Novakova-Marcincinova; J. Novak-Marcincin

    2012-01-01

    Paper presents knowledge about types of test in area of materials properties of selected methods of rapid prototyping technologies. In today used rapid prototyping technologies for production of models and final parts are used materials in initial state as solid, liquid or powder material structure. In solid state are used various forms such as pellets, wire or laminates. Basic range materials include paper, nylon, wax, resins, metals and ceramics. In Fused Deposition Mod...

  5. Tetrakis(4-tert-butylphenyl) substituted and fused quinoidal porphyrins

    KAUST Repository

    Zeng, Wangdong

    2012-01-01

    4-tert-Butylphenyl-substituted and fused quinoidal porphyrins 1 and 2 are prepared for the first time. They show (1) intense one-photon absorption in the far-red/near-infrared region, (2) enhanced two-photon absorption compared with aromatic porphyrin monomers, and (3) amphoteric redox behavior. Their geometry and electronic structure are studied by DFT calculations. This journal is © 2012 The Royal Society of Chemistry.

  6. Tunable thick porous silica coating fabricated by multilayer-by-multilayer bonding of silica nanoparticles for open-tubular capillary chromatographic separation.

    Science.gov (United States)

    Qu, Qishu; Liu, Yuanyuan; Shi, Wenjun; Yan, Chao; Tang, Xiaoqing

    2015-06-19

    A simple coating procedure employing a multilayer-by-multilayer process to modify the inner surface of bare fused-silica capillaries with silica nanoparticles was established. The silica nanoparticles were adsorbed onto the capillary wall via a strong electrostatic interaction between amino functional groups and silica particles. The thickness of the coating could be tuned from 130 to 600 nm by increasing the coating cycles from one to three. Both the retention factor and the resolution were greatly increased with increasing coating cycles. The loading capacity determined by naphthalene in the column with three coating cycles is 152.1 pmol. The effects of buffer concentration and pH value on the stability of the coating were evaluated. The retention reproducibility of the separation of toluene was 0.8, 1.2, 2.3, and 4.5%, respectively, for run-to-run, day-to-day, column-to-column, and batch-to-batch, respectively. The chromatographic performance of these columns was evaluated by both capillary liquid chromatography and open-tubular capillary electrochromatography (OT-CEC). Separation of aromatic hydrocarbons in the column with three coating cycles provided high theoretical plate numbers (up to 269,280 plates m(-1) for toluene) and short separation time (<15 min) by using OT-CEC mode. The method was also used to separate egg white proteins. Both acidic and basic proteins as well as four glycoisoforms were separated in a single run. Copyright © 2015 Elsevier B.V. All rights reserved.

  7. Cellular membrane trafficking of mesoporous silica nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Fang, I-Ju [Iowa State Univ., Ames, IA (United States)

    2012-01-01

    This dissertation mainly focuses on the investigation of the cellular membrane trafficking of mesoporous silica nanoparticles. We are interested in the study of endocytosis and exocytosis behaviors of mesoporous silica nanoparticles with desired surface functionality. The relationship between mesoporous silica nanoparticles and membrane trafficking of cells, either cancerous cells or normal cells was examined. Since mesoporous silica nanoparticles were applied in many drug delivery cases, the endocytotic efficiency of mesoporous silica nanoparticles needs to be investigated in more details in order to design the cellular drug delivery system in the controlled way. It is well known that cells can engulf some molecules outside of the cells through a receptor-ligand associated endocytosis. We are interested to determine if those biomolecules binding to cell surface receptors can be utilized on mesoporous silica nanoparticle materials to improve the uptake efficiency or govern the mechanism of endocytosis of mesoporous silica nanoparticles. Arginine-glycine-aspartate (RGD) is a small peptide recognized by cell integrin receptors and it was reported that avidin internalization was highly promoted by tumor lectin. Both RGD and avidin were linked to the surface of mesoporous silica nanoparticle materials to investigate the effect of receptor-associated biomolecule on cellular endocytosis efficiency. The effect of ligand types, ligand conformation and ligand density were discussed in Chapter 2 and 3. Furthermore, the exocytosis of mesoporous silica nanoparticles is very attractive for biological applications. The cellular protein sequestration study of mesoporous silica nanoparticles was examined for further information of the intracellular pathway of endocytosed mesoporous silica nanoparticle materials. The surface functionality of mesoporous silica nanoparticle materials demonstrated selectivity among the materials and cancer and normal cell lines. We aimed to determine

  8. Airborne silica levels in an urban area

    Energy Technology Data Exchange (ETDEWEB)

    De Berardis, B. [Dipartimento di Tecnologie e Salute, Istituto Superiore di Sanita, Viale Regina Elena, 299, 00161 Rome (Italy)]. E-mail: barbara.deberardis@iss.it; Incocciati, E. [CONTARP Consulenza Tecnica Accertamento Rischi e Prevenzione, INAIL Direzione Generale, 00143 Rome (Italy); Massera, S. [CONTARP Consulenza Tecnica Accertamento Rischi e Prevenzione, INAIL Direzione Generale, 00143 Rome (Italy); Gargaro, G. [CONTARP Consulenza Tecnica Accertamento Rischi e Prevenzione, INAIL Direzione Generale, 00143 Rome (Italy); Paoletti, L. [Dipartimento di Tecnologie e Salute, Istituto Superiore di Sanita, Viale Regina Elena, 299, 00161 Rome (Italy)

    2007-09-01

    In order to evaluate the exposure levels of the general population we studied the concentrations of silica particles in the inhalable particulate fraction (PM10) in different meteorological-climate periods in an urban area of Rome. In order to determine the concentration and the granulometric spectrum of silica particles, PM10 sampled by a cascade impactor was analysed by X-ray diffractometry (XRD) and by scanning electron microscopy equipped with a thin-window system for X-ray microanalysis (SEM/EDX). Over the period September 2004-October 2005 the abundance of silica particles as evaluated by SEM/EDX ranged from 1.6 to 10.4% of the total PM10 particulate, with a weight concentration of free crystalline silica, evaluated by XRD, in the range 0.25-2.87 {mu}g/m{sup 3}. The mean diameter of silica particles ranged from 0.3 to 10.5 {mu}m, with more than 87% of particles having a diameter of less than 2.5 {mu}m. The correlations between SEM/EDX and XRD data seem to suggest that the airborne silica particles in the urban location studied were mainly in the form crystalline silica. A strong relationship was found between the meteorological-climate conditions and the concentration level of free crystalline silica. This result suggests that the Southern winds from the Sahara desert carry an important amount of silica particles into Mediterranean Europe.

  9. Nanoporous silica membranes with high hydrothermal stability

    DEFF Research Database (Denmark)

    Boffa, Vittorio; Magnacca, Giualiana; Yue, Yuanzheng

    Despite the use of sol-gel derived nanoporous silica membranes in substitution of traditional separation processes is expected leading to vast energy savings, their intrinsic poor steam-stability hampers their application at an industrial level. Transition metal ions can be used as dopant...... to improve the stability of nanoporous silica structure. This work is a quantitative study on the impact of type and concentration of transition metal ions on the microporous structure and stability of amorphous silica-based membranes, which provides information on how to design chemical compositions...... and synthetic paths for the fabrication of silica-based membranes with a well accessible and highly stabile nanoporous structure...

  10. Oil absorption in mesoporous silica particles

    Directory of Open Access Journals (Sweden)

    Radislav Filipović

    2010-12-01

    Full Text Available Mesoporous silica particles were prepared from highly basic sodium silicate solutions, having different silica modulus and SiO2 concentrations, by adding sulphuric acid at different temperatures. Pore structure of prepared silica particles (aggregates is strongly influenced by processing conditions and easy controllable in broad range of the specific surface area, pore size, pore volume and size distribution. It is shown that there is a clear correlation between volume of absorbed oil and processing parameters used in preparation of silica aggregates. Thus, oil absorption is higher in the samples prepared from sodium silicate solution with higher SiO2 concentration and at higher synthesis temperature.

  11. Practical Hydrogen Loading of Air Silica Fibres

    DEFF Research Database (Denmark)

    Sørensen, Henrik Rokkjær; Jensen, Jesper Bevensee; Jensen, Jesper Bo Damm

    2005-01-01

    A method for hydrogen-loading air-silica optical fibres has been developed allowing out-diffusion times comparable to standard step-index fibres. Examples of the first grating written in Ge-doped air-silica fibres using a 266nm UV-laser are shown.......A method for hydrogen-loading air-silica optical fibres has been developed allowing out-diffusion times comparable to standard step-index fibres. Examples of the first grating written in Ge-doped air-silica fibres using a 266nm UV-laser are shown....

  12. A hierarachical data structure representation for fusing multisensor information

    Energy Technology Data Exchange (ETDEWEB)

    Maren, A.J. [Tennessee Univ., Tullahoma, TN (United States). Space Inst.; Pap, R.M.; Harston, C.T. [Accurate Automation Corp., Chattanooga, TN (United States)

    1989-12-31

    A major problem with MultiSensor Information Fusion (MSIF) is establishing the level of processing at which information should be fused. Current methodologies, whether based on fusion at the data element, segment/feature, or symbolic levels, are each inadequate for robust MSIF. Data-element fusion has problems with coregistration. Attempts to fuse information using the features of segmented data relies on a Presumed similarity between the segmentation characteristics of each data stream. Symbolic-level fusion requires too much advance processing (including object identification) to be useful. MSIF systems need to operate in real-time, must perform fusion using a variety of sensor types, and should be effective across a wide range of operating conditions or deployment environments. We address this problem through developing a new representation level which facilitates matching and information fusion. The Hierarchical Data Structure (HDS) representation, created using a multilayer, cooperative/competitive neural network, meets this need. The HDS is an intermediate representation between the raw or smoothed data stream and symbolic interpretation of the data. it represents the structural organization of the data. Fused HDSs will incorporate information from multiple sensors. Their knowledge-rich structure aids top-down scene interpretation via both model matching and knowledge-based region interpretation.

  13. A hierarachical data structure representation for fusing multisensor information

    Energy Technology Data Exchange (ETDEWEB)

    Maren, A.J. (Tennessee Univ., Tullahoma, TN (United States). Space Inst.); Pap, R.M.; Harston, C.T. (Accurate Automation Corp., Chattanooga, TN (United States))

    1989-01-01

    A major problem with MultiSensor Information Fusion (MSIF) is establishing the level of processing at which information should be fused. Current methodologies, whether based on fusion at the data element, segment/feature, or symbolic levels, are each inadequate for robust MSIF. Data-element fusion has problems with coregistration. Attempts to fuse information using the features of segmented data relies on a Presumed similarity between the segmentation characteristics of each data stream. Symbolic-level fusion requires too much advance processing (including object identification) to be useful. MSIF systems need to operate in real-time, must perform fusion using a variety of sensor types, and should be effective across a wide range of operating conditions or deployment environments. We address this problem through developing a new representation level which facilitates matching and information fusion. The Hierarchical Data Structure (HDS) representation, created using a multilayer, cooperative/competitive neural network, meets this need. The HDS is an intermediate representation between the raw or smoothed data stream and symbolic interpretation of the data. it represents the structural organization of the data. Fused HDSs will incorporate information from multiple sensors. Their knowledge-rich structure aids top-down scene interpretation via both model matching and knowledge-based region interpretation.

  14. Antagonist wear by polished zirconia crowns.

    Science.gov (United States)

    Hartkamp, Oliver; Lohbauer, Ulrich; Reich, Sven

    The aim of this in vivo study was to measure antagonist wear caused by polished monolithic posterior zirconia crowns over a 24-month period using the intraoral digital impression (IDI) technique. Thirteen zirconia crowns were placed in nine patients. The crowns and adjacent teeth were captured using an intraoral scanner (Lava C.O.S.). The corresponding antagonist teeth and the respective neighboring teeth were also scanned. Scanning was performed immediately after the restoration (baseline) as well as 12 and 24 months after crown placement. Geomagic Qualify software was used to superimpose the follow-up data sets onto the corresponding baseline data set, identify wear sites, and measure maximum vertical height loss in each individual wear site. Overall antagonist wear was then determined as the mean of wear rates measured in all of the individual antagonist units. In addition, wear rates in enamel and ceramic antagonists were analyzed as part of the scope of this study. The maximum mean wear with standard deviation (SD) in the overall sample with a total of nine patients, 13 antagonist units, and 98 evaluable wear sites was 86 ± 23 µm at 12 months, and 103 ± 39 µm at 24 months. The maximum mean wear in the enamel antagonist subgroup was 87 ± 41 µm at 12 months, and 115 ± 71 µm at 24 months; and in the ceramic antagonist subgroup 107 ± 22 µm at 12 months, and 120 ± 27 µm at 24 months. The wear rates determined in this study are comparable to those of existing studies. The IDI technique of wear analysis can be carried out in a practical manner and produces useful results.

  15. Germanium content in Polish hard coals

    Directory of Open Access Journals (Sweden)

    Makowska Dorota

    2016-01-01

    Full Text Available Due to the policy of the European Union, it is necessary to search for new sources of scarce raw materials. One of these materials is germanium, listed as a critical element. This semi-metal is widely used in the electronics industry, for example in the production of semiconductors, fibre optics and solar cells. Coal and fly ash from its combustion and gasification for a long time have been considered as a potential source of many critical elements, particularly germanium. The paper presents the results of germanium content determination in the Polish hard coal. 23 coal samples of various coal ranks were analysed. The samples were collected from 15 mines of the Upper Silesian Coal Basin and from one mine of the Lublin Coal Basin. The determination of germanium content was performed with the use of Atomic Absorption Spectrometry with Electrothermal Atomization (GFAAS. The investigation showed that germanium content in the analysed samples was at least twice lower than the average content of this element in the hard coals analysed so far and was in the range of 0.08 ÷ 1.28 mg/kg. Moreover, the content of Ge in the ashes from the studied coals does not exceed 15 mg/kg, which is lower than the average value of Ge content in the coal ashes. The highest content of this element characterizes coals of the Lublin Coal Basin and young coals type 31 from the Vistula region. The results indicate a low utility of the analysed coal ashes as a source of the recovery of germanium. On the basis of the analyses, the lack of the relationship between the content of the element and the ash content in the tested coals was noted. For coals of the Upper Silesian Coal Basin, the relationship between the content of germanium in the ashes and the depth of the seam was observed.

  16. Studies on polishing of Ti and Ag-Pd-Cu-Au alloy with five dental abrasives.

    Science.gov (United States)

    Hirata, T; Nakamura, T; Takashima, F; Maruyama, T; Taira, M; Takahashi, J

    2001-08-01

    Titanium (Ti) and Ag-Pd-Cu-Au alloy were examined for their polishing behaviour by conducting manually controlled polishing tests using five dental abrasives [carborundum point (CR) and silicone points (R1 and R2)] driven by a high torque micromotor with rotational speeds ranging from 2000 to 15 000 r.p.m. Polishing of Ti resulted in less volume of removal upon polishing, a rougher surface and larger loss of abrasives, compared with polishing of Ag-Pd-Cu-Au alloy. Polishing of Ti with a rotational speed of 15 000 r.p.m. led to the largest volume of removal upon polishing, whilst that of 10 000 r.p.m. produced the optimal volume for Ag-Pd-Cu-Au alloy. It was concluded that Ti was much more difficult to polish, requiring special care (e.g. frequent exchange of abrasives). Development of new abrasives for polishing Ti is required.

  17. The study of optimization on process parameters of high-accuracy computerized numerical control polishing

    Science.gov (United States)

    Huang, Wei-Ren; Huang, Shih-Pu; Tsai, Tsung-Yueh; Lin, Yi-Jyun; Yu, Zong-Ru; Kuo, Ching-Hsiang; Hsu, Wei-Yao; Young, Hong-Tsu

    2017-09-01

    Spherical lenses lead to forming spherical aberration and reduced optical performance. Consequently, in practice optical system shall apply a combination of spherical lenses for aberration correction. Thus, the volume of the optical system increased. In modern optical systems, aspherical lenses have been widely used because of their high optical performance with less optical components. However, aspherical surfaces cannot be fabricated by traditional full aperture polishing process due to their varying curvature. Sub-aperture computer numerical control (CNC) polishing is adopted for aspherical surface fabrication in recent years. By using CNC polishing process, mid-spatial frequency (MSF) error is normally accompanied during this process. And the MSF surface texture of optics decreases the optical performance for high precision optical system, especially for short-wavelength applications. Based on a bonnet polishing CNC machine, this study focuses on the relationship between MSF surface texture and CNC polishing parameters, which include feed rate, head speed, track spacing and path direction. The power spectral density (PSD) analysis is used to judge the MSF level caused by those polishing parameters. The test results show that controlling the removal depth of single polishing path, through the feed rate, and without same direction polishing path for higher total removal depth can efficiently reduce the MSF error. To verify the optical polishing parameters, we divided a correction polishing process to several polishing runs with different direction polishing paths. Compare to one shot polishing run, multi-direction path polishing plan could produce better surface quality on the optics.

  18. Infestation of Polish Agricultural Soils by Plasmodiophora Brassicae Along The Polish-Ukrainian Border

    Directory of Open Access Journals (Sweden)

    Jędryczka Małgorzata

    2014-07-01

    Full Text Available There has been a rapid, worldwide increase in oilseed rape production that has resulted in enormous intensification of oilseed rape cultivation, leading to tight rotations. This in turn, has caused an accumulation of pests as well as foliar and soil-borne diseases. Recently, clubroot has become one of the biggest concerns of oilseed rape growers. Clubroot is caused by the soil-borne protist Plasmodiophora brassicae Woronin. The pathogen may be present in groundwater, lakes, and irrigation water used in sprinkling systems. It can be easily transmitted from one field to another not only by water, but also by soil particles and dust transmitted by wind and on machinery. The aim of our overall study was to check for P. brassicae infestation of Polish agricultural soils. This paper presents the 2012 results of a study performed along the Polish-Ukrainian border in two provinces: Lublin (Lubelskie Voivodeship and the Carpathian Foothills (Podkarpackie Voivodeship, in south-east Poland. Monitoring was done in 11 counties, including nine rural and two municipal ones. In total, 40 samples were collected, out of which 36 were collected from fields located in rural areas and four from municipal areas, with two per municipal region. Each sample was collected at 8-10 sites per field, using a soil auger. The biotest to detect the presence of P. brassicae was done under greenhouse conditions using seedlings of the susceptible Brassicas: B. rapa ssp. pekinensis and the Polish variety of oilseed rape B. napus cv. Monolit. Susceptible plants grown in heavily infested soils produced galls on their roots. A county was regarded as free from the pathogen, if none of the bait plants became infected. The pathogen was found in three out of 40 fields monitored (7.5% in the Carpathian Foothill region. The fields were located in two rural counties. The pathogen was not found in Lublin province, and was also not detected in any of the municipal counties. The detection with

  19. Delayed polishing technique on glass–ionomer restorations

    Directory of Open Access Journals (Sweden)

    Masao Irie

    2009-05-01

    Full Text Available This in vitro study evaluated the effect of polishing after 1-day storage in water on the gap-formation around a Class V and Class I restorations, using a resin-modified glass–ionomer and a conventional glass–ionomer materials. The study also examined the gap-formation in another two different cervical restorations, a cervical cavity: incisally bordered by enamel and cervically by dentin and a root surface cavity of these restorative materials, which may be effects of this polishing procedure. This study evaluated the effects of delayed versus immediate polishing to permit maturation on: (1 interfacial gap-formation around resin-modified (RMGIC and conventional (CGIC in three types of cervical restorations, (2 interfacial gap-formation around highly viscous conventional glass–ionomer cement (HCGIC in Class I restorations. After polishing procedure, either: (i immediately (3 or 6 min after setting or (ii after 24 h storage, the maximum the restored teeth were sectioned in a mesio-distal direction through the center of the restorations. The presence or absence of interfacial-gaps was measured at 14 points (each 0.5-mm apart along the cavity restoration interface. For various restorative cases, significant differences (p < 0.05 in gap-width or gap-incidence, were observed between polishing (i immediately and (ii after 1-day storage.

  20. Nail polish as a source of exposure to triphenyl phosphate.

    Science.gov (United States)

    Mendelsohn, Emma; Hagopian, Audrey; Hoffman, Kate; Butt, Craig M; Lorenzo, Amelia; Congleton, Johanna; Webster, Thomas F; Stapleton, Heather M

    2016-01-01

    Triphenyl phosphate (TPHP) is primarily used as either a flame retardant or plasticizer, and is listed as an ingredient in nail polishes. However, the concentration of TPHP in nail polish and the extent of human exposure following applications have not been previously studied. We measured TPHP in ten different nail polish samples purchased from department stores and pharmacies in 2013-2014. Concentrations up to 1.68% TPHP by weight were detected in eight samples, including two that did not list TPHP as an ingredient. Two cohorts (n=26 participants) were recruited to assess fingernail painting as a pathway of TPHP exposure. Participants provided urine samples before and after applying one brand of polish containing 0.97% TPHP by weight. Diphenyl phosphate (DPHP), a TPHP metabolite, was then measured in urine samples (n=411) and found to increase nearly seven-fold 10-14h after fingernail painting (pexposure, ten participants also painted their nails and painted synthetic nails adhered to gloves on two separate occasions, and collected urine for 24h following applications. Urinary DPHP was significantly diminished when wearing gloves, suggesting that the primary exposure route is dermal. Our results indicate that nail polish may be a significant source of short-term TPHP exposure and a source of chronic exposure for frequent users or those occupationally exposed. Copyright © 2015 Elsevier Ltd. All rights reserved.

  1. Conversion of South African Coal Fly Ash into High-Purity ZSM-5 Zeolite without Additional Source of Silica or Alumina and Its Application as a Methanol-to-Olefins Catalyst

    OpenAIRE

    Roland N. M. Missengue; Pit Losch; Nicholas M. Musyoka; Benoit Louis; Patrick Pale; Leslie F. Petrik

    2018-01-01

    Characteristics of ZSM-5 synthesized from H2SO4-treated coal fly ash and fused coal fly ash extracts are compared in this study. In the synthesis process, fused coal fly ash extract (without an additional silica source) was used in the synthesis of ZSM-5. The effect of the structure-directing agent (tetrapropylammonium bromide, 1,6-hexanediamine or 1-propylamine) on the properties and methanol-to-olefins (MTO) effectiveness of the fly ash-based ZSM-5 was also investigated. A pure ZSM-5 synthe...

  2. Volume nanograting formation in laser-silica interaction as a result of the 1D plasma-resonance ionization instability

    Energy Technology Data Exchange (ETDEWEB)

    Gildenburg, V. B., E-mail: gil@appl.sci-nnov.ru; Pavlichenko, I. A. [University of Nizhny Novgorod, Nizhny Novgorod 603950 (Russian Federation); Institute of Applied Physics, Russian Academy of Sciences, Nizhny Novgorod 603950 (Russian Federation)

    2016-08-15

    The initial stage of the small-scale ionization-induced instability developing inside the fused silica volume exposed to the femtosecond laser pulse is studied as a possible initial cause of the self-organized nanograting formation. We have calculated the spatial spectra of the instability with the electron-hole diffusion taken into account for the first time and have found that it results in the formation of some hybrid (diffusion-wave) 1D structure with the spatial period determined as the geometrical mean of the laser wavelength and characteristic diffusion length of the process considered. Near the threshold of the instability, this period occurs to be approximately equal to the laser half-wavelength in the silica, close to the one experimentally observed.

  3. Synthesis of uniform carbon at silica nanocables and luminescent silica nanotubes with well controlled inner diameters

    International Nuclear Information System (INIS)

    Qian Haisheng; Yu Shuhong; Ren Lei; Yang Yipeng; Zhang Wei

    2006-01-01

    Uniform carbon at silica nanocables and silica nanotubes with well-controlled inner diameters can be synthesized in an easy way by a sacrificial templating method. This was performed using carbon nanofibres as hard templates that were synthesized previously by a hydrothermal carbonization process. Silica nanotubes with well-controlled inner diameters were synthesized from carbon at silica core-shell nanostructures by removal of the core carbon component. The inner diameters of the as-prepared silica nanotubes can be well controlled from several nanometres to hundreds of nanometres by adjusting the diameters of the carbon nanofibres. The silica nanotubes synthesized by this method display strong photoluminescence in ultraviolet at room temperature. Such uniform silica nanotubes might find potential applications in many fields such as encapsulation, catalysis, chemical/biological separation, and sensing

  4. Silica gel matrix immobilized Chlorophyta hydrodictyon africanum ...

    African Journals Online (AJOL)

    Aghomotsegin

    2015-08-05

    Aug 5, 2015 ... immobilization of 300 mg per gram silica. Maximum immobilization was 400 mg biomass per gram silica. Sorption capacity increased with an increase in initial dye concentration and reached equilibrium within. 30 min. Three models were used to simulate kinetic data and the pseudo–second order model ...

  5. Subclinical nephrotoxicity associated with occupational silica ...

    African Journals Online (AJOL)

    Objective: To determine early signs of renal injury due to occupational silica exposure. Design: Cross-sectional analytical research. Settings: Kenyatta National Hospital for the referent population and Clayworks ceramics, bricks and tiles factory for the assessment of occupational silica exposure. Subjects: Thirty three ...

  6. Medium-range order in metamict silicas

    International Nuclear Information System (INIS)

    Qin, L.C.; Hobbs, L.W.

    1995-01-01

    The first sharp diffraction peak from various forms of aperiodic silica was studied. Materials examined include vitreous silica, electron-metallic quartz, neutron-metallic quartz, and Si + ion-implanted quartz. The peak is attributed to the dominant structural rings existing in the materials, or modification thereof. The anomalous behavior of this peak is also discussed

  7. Bioinspired synthesis of new silica structures.

    Science.gov (United States)

    Patwardhan, Siddharth V; Mukherjee, Niloy; Steintz-Kannan, Miriam; Clarson, Stephen J

    2003-05-21

    Silicon and oxygen are the two most abundant elements in the Earth's crust but despite the vast scientific literature on crystalline and amorphous silica, new chemistries, structures and applications continue to be discovered for compounds formed from these elements--thus we present here for the first time the formation of new amorphous silica structures that were uniquely synthesized by a bioinspired synthetic system.

  8. Silica gel matrix immobilized Chlorophyta hydrodictyon africanum ...

    African Journals Online (AJOL)

    Chlorophyta hydrodictyon africanum was immobilized on a silica gel matrix to improve its mechanical properties. The algae-silica gel adsorbent was used for batch sorption studies of a cationic dye, methylene blue (MB). Optimum adsorption was obtained with a dosage of 0.8 g bio sorbent. Results from sorption studies ...

  9. Active and passive silica waveguide integration

    DEFF Research Database (Denmark)

    Hübner, Jörg; Guldberg-Kjær, Søren Andreas

    2001-01-01

    in existing and future networks without affecting the power budget of the system. Silica on silicon technology offers a unique possibility to selectively dope sections of the integrated circuit with erbium where amplification is desired. Some techniques for active/passive integration are reviewed and a silica...

  10. Magnetic core-shell silica particles

    NARCIS (Netherlands)

    Claesson, E.M.

    2007-01-01

    This thesis deals with magnetic silica core-shell colloids and related functionalized silica structures. Synthesis routes have been developed and optimized. The physical properties of these colloids have been investigated, such as the magnetic dipole moment, dipolar structure formation and

  11. [Polish medical ethics in the period 1945-1980].

    Science.gov (United States)

    Wichrowski, Marek

    2003-01-01

    The purpose of this article is o present that main currents of Polish medical ethics in the years 1945-1980, which the author treats as the 'prehistory' of Poland's contemporary bioethics. The author begins by ascertaining the post-war disappearance of two Polish traditions--that of the Warsaw school of philosopher-physicians (known in the West as the Polish School of Philosophy of Medicine) and the Lwów-Warsaw School of Philosophy. The political system that come into being after 1945 was not conducive to the development of medical ethics, but several clear orientations may be discerned in the utterances of physicians, lawyers, moral technologlans and academic philosophers. The analysis begins with Catholic ethics in its archaic 1950s-vintage form. The author then presents the thinking of ethicians Independent of both the Church and Marxism (the milieu of the journal 'Etyka') as well as the deontological writings of physicians.

  12. Body conformation comparison of Czech and Polish Hucul horses

    Directory of Open Access Journals (Sweden)

    Zita Matoušová Malbohanová

    2004-01-01

    Full Text Available Measurements of 17 body measures and 11 indices of body conformation on 209 breeding individuals of the Hucul horse were used to analyse the effect of country of origin (Poland and the Czech Republic, sex (stallions and mares, age (5 classes and sire line (Gurgul, Goral, Oušor, Hroby, Polan, Pietrosu, Prislop. All horses were measured by one person. Measures and indexes were analysed by the GLM procedure. The main effect was the country of origin. Highly significant differences were found between both Polish and Czech horses in two thirds of measurements and in more than half of indices. The Czech Hucul horses are significantly higher, longer, wider in pelvis and have longer head than Polish horses. On the contrary to the Czech horses are Polish horses more compact, massive and have deeper chest. Their cannon bone in relation to height of wither is wider.

  13. Human Factors in Nuclear Power Engineering in Polish Conditions

    Directory of Open Access Journals (Sweden)

    Agnieszka Kaczmarek-Kacprzak

    2014-09-01

    Full Text Available The paper “Human factors in nuclear power engineering in Polish conditions” focuses on analysis of dynamics of preparing Polish society to build fi rst nuclear power plant in XXI century in Poland. Authors compare experience from constructing nuclear power plant Sizewell B (Great Britain and Sizewell C, which is in preparation phase with polish nuclear power program. Paper includes aspects e.g. of creating nuclear safety culture and social opinion about investment. Human factors in nuclear power engineering are as well important as relevant economical and technical factors, but very often negligible. In Poland where history about Czarnobyl is still alive, and social opinion is created on emotions after accident in Fukushima, human factors are crucial and should be under comprehensive consideration.

  14. The social shaping of innovation in polish companies

    DEFF Research Database (Denmark)

    Lorentzen, Anne

    2003-01-01

    The paper deals with strategies of innovation in Polish manufacturing companies. The point of departure is a theoretical framework of enterprise level innovation, and of the factors forming strategies of innovation on enterprise level. The paper analyses evidence from 23 Polish companies...... and presents two cases more in detail. The analysis shows that the Polish companies have all been quite innovative, mostly in relation to product innovation. They choose innovation strategies, which are incremental more than radical, and they tend to differentiate their product range rather than to specialise....... They consider quality development a must in the fight for market shares and they adapt equipment and organisation to this goal. The factors forming and determining the strategies of the companies count the technological knowledge and expertise of the owner/founder, the structural changes of the market...

  15. FTIR thermal analysis on organofunctionalized silica gel

    Directory of Open Access Journals (Sweden)

    Foschiera José L.

    2001-01-01

    Full Text Available Silica gel modified with organic groups is widely used as a stationary phase for liquid chromatography. Grafting synthesis can be used to obtain stable modified silica gel surfaces. In this work, silica gel (10 nm of pore diameter and surface area of 320 m² g-1 was chemically modified with 3-chloropropyltrimethoxysilane or 3-aminopropyltrimethoxysilane and reacted with aniline, p-anisidine, benzylamine and 3-phenylpropylchloride in order to yield aromatic groups immobilized on the silica gel surface. Infrared spectroscopy was utilized for characterization of the aromatic groups grafted on the silica gel surface, using a quartz cell. The solids were heated at several temperatures in high vacuum and the infrared band areas of the organic groups were used to evaluate the thermal stability.

  16. The Pozzolanic reaction of silica fume

    DEFF Research Database (Denmark)

    Jensen, Ole Mejlhede

    2012-01-01

    Silica fume is a very important supplementary cementitious binder in High-Performance and Ultra High-Performance Concretes. Through its pozzolanic reaction the silica fume densifies the concrete micro-structure, in particular it strengthens the paste-aggregate interfacial transition zone....... In the present paper different aspects of the pozzolanic reaction of silica fume are investigated. These include chemical shrinkage, isothermal heat development and strength development. Key data for these are given and compared with theoretical calculations, and based on presented measurements the energy...... of activation of the pozzolanic reaction of silica fume is estimated. The results show that the pozzolanic reaction of silica fume has notable differences from Portland cement hydration....

  17. [The historical significance of the Polish medical faculty in Edinburgh].

    Science.gov (United States)

    Nowak, K

    1999-01-01

    The Polish Medical Faculty at the University of Edinburgh was a unique phenomenon in the history of universities. Established during the Second World War in 1941 as an entirely autonomous Polish academic institution, the Faculty trained 228 doctors and awarded 19 PhD degrees during its nine years of formal existence (1941-1949). In reviewing its almost 60-year old history, seen in the context of the involvement of the elite of both the political and academic establishments, the splendour of various celebrations and its graduates devotion in keeping the "Edinburgh experiment" alive, the author makes a case for the long-term historical and psychological significance of events well outlasting the period of formal activity of the Faculty. The history of the Faculty is well documented, but the long term outcome in terms of its lasting historical importance is gradually emerging with the passage of time. It has become an indisputable testimony to the generosity and hospitality of the Scottish (political and) academic establishment and a lasting proof of the special liaison between the Scots and the Poles. The Faculty's importance and psychological significance to the rich historical heritage of Polish medicine and the notion of patriotism and loyalty to Polishness have become apparent in the ensuing decades of its carefully maintained tradition. The existence of the Polish Medical Faculty has become an extraordinary asset in the history of Scottish universities, but for the Polish tradition both in Poland and throughout its rich diaspora it constitutes an increasingly valuable historical event which deserves to be cultivated and passed on to younger generations so that it may continue bringing further dividends, so important to national identity, achievement, dignity and pride.

  18. Verbalization the Concept of Dignity in Polish Dictionaries

    Directory of Open Access Journals (Sweden)

    Chaban Vasylyna

    2016-12-01

    Full Text Available Background: The object of the study is the concept of DIGNITY. The justification of the research is predetermined by the lack of such investigation in Polish linguistics. The background for the article is also determined by the lack of similar studies in the sphere of Cognitive Linguistics. Purpose: The article aims at analysing the cultural concept of DIGNITY in the minds of the bearers of the Polish language and culture based on the data incorporated from the lexicographical sources and collection of folk sayings and proverbs. Results: The article dwells upon the most important features of this concept in the Polish language and culture. The study investigates the language conceptualization of this concept in the system of the Polish language and folk maxims and sayings. The definition of the lexeme of dignity reveals the compliance with higher moral principles and the understanding of value; good name, good character claiming attention and respect; the last name. DIGNITY is the principal regulating mechanism of behaviour and development of positive human values which become apparent in the process of human interaction. A man of worth respects himself and is as well proud to be an honourable man. DIGNITY concerns both a separate human and the society in general; it could be regarded as both individual and collective notion. Discussion: The suggested analysis revealed cultural and linguistic peculiarities of the concept of DIGNITY in the Polish language and culture. The conducted research is not exhaustive since it provides potential perspectives for further research of the Polish concept of DIGNITY, in particular, in terms of comparative studies with correlative concepts in Ukrainian and English languages and cultures with the help of the cognitive definition method.

  19. Evolution of polish E-commerce - main trends and perspectives

    OpenAIRE

    Chodak, Grzegorz

    2008-01-01

    The aim of this paper is to present main phases of Polish e-commerce development and to show its major trends. The author also tries to predict future directions of its development. The whole e-commerce process of development is divided into five phases. The first part of the paper presents the beginnings of Polish e-commerce. Then the following stages of development are discussed with presentation of some key figures e.g. percentage of individuals who ordered goods or services over the Inter...

  20. Polish as a Foreign Language: New Context, Regulations and Prospects

    Directory of Open Access Journals (Sweden)

    Popławska Anna

    2015-10-01

    Full Text Available The article provides an overview of the developments in Poland after the collapse of communism in 1989 from the point of view of foreign language teaching, including a swift reorientation and transition from a public school system with Russian as the main foreign language, to a diversified language teaching market focused on teaching English and other languages. A particular stress is placed on a relatively new phenomenon, being an increased demand and new opportunities for teaching Polish as a foreign language to be further promoted as a result of anticipated amendments to legal regulations governing the status and certification of the Polish language.

  1. Laser polishing for topography management of accelerator cavity surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Liang [College of William and Mary, Williamsburg, VA (United States); Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Klopf, J. Mike [College of William and Mary, Williamsburg, VA (United States); Reece, Charles E. [Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States); Kelley, Michael J. [College of William and Mary, Williamsburg, VA (United States); Thomas Jefferson National Accelerator Facility (TJNAF), Newport News, VA (United States)

    2015-07-20

    Improved energy efficiency and reduced cost are greatly desired for advanced particle accelerators. Progress toward both can be made by atomically-smoothing the interior surface of the niobium superconducting radiofrequency accelerator cavities at the machine's heart. Laser polishing offers a green alternative to the present aggressive chemical processes. We found parameters suitable for polishing niobium in all surface states expected for cavity production. As a result, careful measurement of the resulting surface chemistry revealed a modest thinning of the surface oxide layer, but no contamination.

  2. Mechanistic, kinetic, and processing aspects of tungsten chemical mechanical polishing

    Science.gov (United States)

    Stein, David

    This dissertation presents an investigation into tungsten chemical mechanical polishing (CMP). CMP is the industrially predominant unit operation that removes excess tungsten after non-selective chemical vapor deposition (CVD) during sub-micron integrated circuit (IC) manufacture. This work explores the CMP process from process engineering and fundamental mechanistic perspectives. The process engineering study optimized an existing CMP process to address issues of polish pad and wafer carrier life. Polish rates, post-CMP metrology of patterned wafers, electrical test data, and synergy with a thermal endpoint technique were used to determine the optimal process. The oxidation rate of tungsten during CMP is significantly lower than the removal rate under identical conditions. Tungsten polished without inhibition during cathodic potentiostatic control. Hertzian indenter model calculations preclude colloids of the size used in tungsten CMP slurries from indenting the tungsten surface. AFM surface topography maps and TEM images of post-CMP tungsten do not show evidence of plow marks or intergranular fracture. Polish rate is dependent on potassium iodate concentration; process temperature is not. The colloid species significantly affects the polish rate and process temperature. Process temperature is not a predictor of polish rate. A process energy balance indicates that the process temperature is predominantly due to shaft work, and that any heat of reaction evolved during the CMP process is negligible. Friction and adhesion between alumina and tungsten were studied using modified AFM techniques. Friction was constant with potassium iodate concentration, but varied with applied pressure. This corroborates the results from the energy balance. Adhesion between the alumina and the tungsten was proportional to the potassium iodate concentration. A heuristic mechanism, which captures the relationship between polish rate, pressure, velocity, and slurry chemistry, is presented

  3. Implementation of the Bulgarian-Polish online dictionary

    Directory of Open Access Journals (Sweden)

    Ludmila Dimitrova

    2015-11-01

    Full Text Available Implementation of the Bulgarian-Polish online dictionary The paper describes the implementation of an online Bulgarian-Polish dictionary as a technological tool for applications in digital humanities. This bilingual digital dictionary is developed in the frame of the joint research project “Semantics and Contrastive Linguistics with a focus on a bilingual electronic dictionary” between IMI-BAS and ISS-PAS, supervised by L. Dimitrova (IMI-BAS and V. Koseska-Toszewa (ISS-PAS. In addition, the main software tools for web-presentation of the dictionary are described briefly.

  4. Confocal Raman spectrocopy for the analysis of nail polish evidence.

    Science.gov (United States)

    López-López, Maria; Vaz, Joana; García-Ruiz, Carmen

    2015-06-01

    Nail polishes are cosmetic paints that may be susceptible of forensic analysis offering useful information to assist in a crime reconstruction. Although the nail polish appearance could allow a quick visual identification of the sample, this analysis is subjected to the perception and subjective interpretation of the forensic examiner. The chemical analysis of the nail polishes offers great deal of information not subjected to analyst interpretation. Confocal Raman spectroscopy is a well-suited technique for the analysis of paints due to its non-invasive and non-destructive nature and its ability to supply information about the organic and inorganic components of the sample. In this work, 77 regular and gel nail polishes were analyzed with confocal Raman spectroscopy using two laser wavelengths (532 and 780 nm). The sample behavior under the two laser wavelengths and the differences in the spectra taken at different points of the sample were studied for each nail polish. Additionally, the spectra obtained for all the nail polishes were visually compared. The results concluded that the longer laser wavelength prevents sample burning and fluorescence effects; the similarity among the spectra collected within the sample is not directly related with the presence of glitter particles; and 64% of the samples analyzed showed a characteristic spectrum. Additionally, the use of confocal Raman spectroscopy for the forensic analysis of nail polishes evidence in the form of flakes or smudges on different surfaces were studied. The results showed that both types of evidence can be analyzed by the technique. Also, two non-invasive sampling methods for the collection of the evidence from the nails of the suspect or the victim were proposed: (i) to use acetone-soaked cotton swabs to remove the nail varnishes and (ii) to scrape the nail polish from the nail with a blade. Both approaches, each exhibiting advantages and drawbacks in terms of transport and handling were appropriate

  5. Tree Classification with Fused Mobile Laser Scanning and Hyperspectral Data

    Science.gov (United States)

    Puttonen, Eetu; Jaakkola, Anttoni; Litkey, Paula; Hyyppä, Juha

    2011-01-01

    Mobile Laser Scanning data were collected simultaneously with hyperspectral data using the Finnish Geodetic Institute Sensei system. The data were tested for tree species classification. The test area was an urban garden in the City of Espoo, Finland. Point clouds representing 168 individual tree specimens of 23 tree species were determined manually. The classification of the trees was done using first only the spatial data from point clouds, then with only the spectral data obtained with a spectrometer, and finally with the combined spatial and hyperspectral data from both sensors. Two classification tests were performed: the separation of coniferous and deciduous trees, and the identification of individual tree species. All determined tree specimens were used in distinguishing coniferous and deciduous trees. A subset of 133 trees and 10 tree species was used in the tree species classification. The best classification results for the fused data were 95.8% for the separation of the coniferous and deciduous classes. The best overall tree species classification succeeded with 83.5% accuracy for the best tested fused data feature combination. The respective results for paired structural features derived from the laser point cloud were 90.5% for the separation of the coniferous and deciduous classes and 65.4% for the species classification. Classification accuracies with paired hyperspectral reflectance value data were 90.5% for the separation of coniferous and deciduous classes and 62.4% for different species. The results are among the first of their kind and they show that mobile collected fused data outperformed single-sensor data in both classification tests and by a significant margin. PMID:22163894

  6. Change Detection by Fusing Advantages of Threshold and Clustering Methods

    Science.gov (United States)

    Tan, M.; Hao, M.

    2017-09-01

    In change detection (CD) of medium-resolution remote sensing images, the threshold and clustering methods are two kinds of the most popular ones. It is found that the threshold method of the expectation maximum (EM) algorithm usually generates a CD map including many false alarms but almost detecting all changes, and the fuzzy local information c-means algorithm (FLICM) obtains a homogeneous CD map but with some missed detections. Therefore, we aim to design a framework to improve CD results by fusing the advantages of threshold and clustering methods. Experimental results indicate the effectiveness of the proposed method.

  7. CHANGE DETECTION BY FUSING ADVANTAGES OF THRESHOLD AND CLUSTERING METHODS

    Directory of Open Access Journals (Sweden)

    M. Tan

    2017-09-01

    Full Text Available In change detection (CD of medium-resolution remote sensing images, the threshold and clustering methods are two kinds of the most popular ones. It is found that the threshold method of the expectation maximum (EM algorithm usually generates a CD map including many false alarms but almost detecting all changes, and the fuzzy local information c-means algorithm (FLICM obtains a homogeneous CD map but with some missed detections. Therefore, we aim to design a framework to improve CD results by fusing the advantages of threshold and clustering methods. Experimental results indicate the effectiveness of the proposed method.

  8. Characterising power quality disturbances resulting from current limiting fuse operation

    Directory of Open Access Journals (Sweden)

    N. Ortiz S.

    2011-06-01

    Full Text Available This article presents novel and easily implemented tools for characterising electrical disturbances originated by fuse operations. A methodology is described that (with the use of some descriptors led to identifying electrical disturbances of this kind. The algorithm’s decision thresholds were estimated using machine learning techniques. This work was aimed at providing new tools for assessing power quality, characterising and extracting information from voltage and current records obtained from monitoring distribution systems. MATLAB was used for validating this methodology, receiving voltage and current records of simulated events in ATP-EMTP and also real events as input.

  9. Fused Deposition Technique for Continuous Fiber Reinforced Thermoplastic

    Science.gov (United States)

    Bettini, Paolo; Alitta, Gianluca; Sala, Giuseppe; Di Landro, Luca

    2017-02-01

    A simple technique for the production of continuous fiber reinforced thermoplastic by fused deposition modeling, which involves a common 3D printer with quite limited modifications, is presented. An adequate setting of processing parameters and deposition path allows to obtain components with well-enhanced mechanical characteristics compared to conventional 3D printed items. The most relevant problems related to the simultaneous feeding of fibers and polymer are discussed. The properties of obtained aramid fiber reinforced polylactic acid (PLA) in terms of impregnation quality and of mechanical response are measured.

  10. Metathesis reactions for the synthesis of ring-fused carbazoles

    CSIR Research Space (South Africa)

    Pelly, SC

    2005-12-09

    Full Text Available .; Michael, J. P.; Rousseau, A. L. J. Chem. Soc., Perkin Trans. 1 2000, 1705. (b) de Koning, C. B.; Michael, J. P.; Nhlapo, J. M.; Pathak, R.; van Otterlo, W. A. L. Synlett 2003, 705. (19) For reviews on metathesis, see: (a) Schmalz, H.-G. Angew. Chem., Int... for the Synthesis of Ring-Fused Carbazoles Stephen C. Pelly,? Christopher J. Parkinson,? Willem A. L. van Otterlo,? and Charles B. de Koning*,? Molecular Sciences Institute, School of Chemistry, University of the Witwatersrand, P.O. Wits, 2050 South Africa...

  11. Removing Mid-Spatial Frequency (MSF) Errors Using Stress-Polishing Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This IRAD proposes to evaluate how stress polishing can be used to extend the application of super-polishing to fast aspheres and freeforms, removing sub-aperture...

  12. Bibliography of English-Polish Contrastive Studies in Poland (as of August 1976).

    Science.gov (United States)

    Mieszek, Aleksandra

    This bibliography lists books, articles, papers, theses and dissertations describing English-Polish contrastive studies conducted in Poland. There are 403 works listed in both languages, divided into two groups: General Works and English-Polish Contrastive Studies. (CHK)

  13. Simulation and analysis of an alternative kinematics for improving the polishing uniformity over the surface of polished tiles

    Directory of Open Access Journals (Sweden)

    Weingaertner, W. L.

    2010-10-01

    Full Text Available The present work investigates the possibility of adopting a new kinematics at the industrial polishing lines of porcelain stoneware tile. An alternative motion of the transverse oscillation of the polishing heads is proposed, in which no radical changes in the industries facilities are required. The basic idea is to replace the purely sinus motion of the polishing heads by a rather trapezoid wavelike motion. In theory this could be achieved simply by adopting regular delays at the transverse oscillation motion. Consequences of this alternative kinematics were quantitatively analyzed considering the spatial homogeneity of polishing expected for tiles. Such homogeneity was represented by the coefficient of variation of the distribution of polishing time over the surface, which was in turn determined by means of computational simulations, taking into account the effect of multiple polishing heads.

    El presente trabajo investiga la posibilidad de adoptar una nueva cinemática en las líneas de pulido industrial de baldosas de gres porcelánico. Se propone una propuesta alternativa de la oscilación transversal de los cabezales pulidores, en el que no hay cambios radicales en las instalaciones de las industrias son necesarias. La idea básica consiste en sustituir el movimiento totalmente del seno de los cabezales pulidores por un movimiento ondulatorio trapezoide. En teoría, esto podría lograrse sólo mediante la adopción de los habituales retrasos en el movimiento de oscilación transversal. las consecuencias de esta cinemática fueron analizados cuantitativamente, teniendo en cuenta la homogeneidad espacial de pulido. Tal homogeneidad fora representada por el coeficiente de variación de la distribución de lo tiempo de pulido en la superficie, determinada por medio de simulaciones computacionales, teniendo también en cuenta el efecto de pulido de las cabezas múltiples.

  14. Present and future role of chemical mechanical polishing in wafer bonding

    NARCIS (Netherlands)

    Gui, C.; Elwenspoek, Michael Curt; Gardeniers, Johannes G.E.; Lambeck, Paul

    Almost all direct wafer bonding has been conducted between chemical-mechanically polished substrates or between thin films that were present on top of the polished substrates. Introducing chemical mechanical polishing in the wafer bonding will make a large range of materials suitable for direct

  15. Development of a multisensory arm for process monitoring in Robot Assisted Polishing

    DEFF Research Database (Denmark)

    Pilny, Lukas; Dalla Costa, Giuseppe; Bissacco, Giuliano

    2015-01-01

    Robot Assisted Polishing (RAP) process is capable of achieving surface roughness down to Sa 10 nm on industrial components. In RAP, a robot arm carries a polishing module with controlled contact force utilizing oscillating or rotating tools. In this work a multisensory polishing arm with integrated...

  16. Influence of the brittle behavior of work materials on polishing characteristics

    Science.gov (United States)

    Sakamoto, Satoshi; Gemma, Masaya; Hayashi, Keitoku; Kondo, Yasuo; Yamaguchi, Kenji; Yakou, Takao; Arakawa, Susumu

    2017-09-01

    Diamond electrodeposited wire tools are frequently used to cut thin wafers from hard and brittle materials. However, microcracks sometimes appear during the slicing process. The appearance of microcracks adversely affects slicing efficiency and slicing accuracy. In this study, we examine the influence of brittle behavior on the polishing characteristics such as polishing depth and tool wear. This is the first step toward investigating the influence of the brittle behavior of work materials on slicing characteristics. Ceramics such as alumina, silicon carbide, and zirconia are used as work materials. Even with the same degree of hardness, we found that the polishing depth values were greater for materials exhibiting brittle behavior. In the polishing of high-hardness materials, abrasive grains were badly damaged during the initial stages of polishing. Damage to the abrasive paper was less in wet polishing as compared with dry polishing. Moreover, wet polishing had a greater polishing depth than dry polishing. The polishing characteristics of the brittle materials were similar to the grooving characteristics produced using wire tools; however, both these characteristics depend on the brittle behavior of the work materials. Therefore, by performing simple polishing tests, estimating the state of grooving or slicing using wire tools is possible.

  17. Patterns of Language Use: Polish Migrants from the 1980s and Their Children in Melbourne

    Science.gov (United States)

    Leuner, Beata

    2010-01-01

    This paper investigates the retention of Polish language and culture by first generation Polish migrants from the 1980s and their second generation offspring (aged 15-24) from endogamous and exogamous marriages. We examine various domains such as the home, social networks, visits to Poland, institutions of learning, the Polish media, the Polish…

  18. Polish Migrant Parents of Secondary School Boys in the United Kingdom

    Science.gov (United States)

    Tkacz, Daria; McGhee, Derek

    2016-01-01

    This article focuses on the parents of secondary school Polish boys and their capacity to realise their educational and professional aspirations for their children. Our primary finding is that although many Polish parents face considerable challenges in manoeuvring through the educational system, some Polish parents display a level of agency…

  19. Planning the FUSE Mission Using the SOVA Algorithm

    Science.gov (United States)

    Lanzi, James; Heatwole, Scott; Ward, Philip R.; Civeit, Thomas; Calvani, Humberto; Kruk, Jeffrey W.; Suchkov, Anatoly

    2011-01-01

    Three documents discuss the Sustainable Objective Valuation and Attainability (SOVA) algorithm and software as used to plan tasks (principally, scientific observations and associated maneuvers) for the Far Ultraviolet Spectroscopic Explorer (FUSE) satellite. SOVA is a means of managing risk in a complex system, based on a concept of computing the expected return value of a candidate ordered set of tasks as a product of pre-assigned task values and assessments of attainability made against qualitatively defined strategic objectives. For the FUSE mission, SOVA autonomously assembles a week-long schedule of target observations and associated maneuvers so as to maximize the expected scientific return value while keeping the satellite stable, managing the angular momentum of spacecraft attitude- control reaction wheels, and striving for other strategic objectives. A six-degree-of-freedom model of the spacecraft is used in simulating the tasks, and the attainability of a task is calculated at each step by use of strategic objectives as defined by use of fuzzy inference systems. SOVA utilizes a variant of a graph-search algorithm known as the A* search algorithm to assemble the tasks into a week-long target schedule, using the expected scientific return value to guide the search.

  20. Quinone-fused porphyrins as contrast agents for photoacoustic imaging

    KAUST Repository

    Banala, Srinivas

    2017-06-27

    Photoacoustic (PA) imaging is an emerging non-invasive diagnostic modality with many potential clinical applications in oncology, rheumatology and the cardiovascular field. For this purpose, there is a high demand for exogenous contrast agents with high absorption coefficients in the optical window for tissue imaging, i.e. the near infrared (NIR) range between 680 and 950 nm. We herein report the photoacoustic properties of quinone-fused porphyrins inserted with different transition metals as new highly promising candidates. These dyes exhibit intense NIR absorption, a lack of fluorescence emission, and PA sensitivity in concentrations below 3 nmol mL. In this context, the highest PA signal was obtained with a Zn(ii) inserted dye. Furthermore, this dye was stable in blood serum and free thiol solution and exhibited negligible cell toxicity. Additionally, the Zn(ii) probe could be detected with an up to 3.2 fold higher PA intensity compared to the clinically most commonly used PA agent, ICG. Thus, further exploration of the \\'quinone-fusing\\' approach to other chromophores may be an efficient way to generate highly potent PA agents that do not fluoresce and shift their absorption into the NIR range.