Full Text Available This article deals with the assessment of the reliability of sensitive equipment due to voltage sags. The most frequent problems of power quality are voltage sags. Equipment that cannot withstand short-term voltage sag is defined as sensitive device. Sensitivity of such equipment can be described by the voltage–tolerance curves. A device (generator to generate voltage sags (also interruptions with duration at least 1 ms has been designed and developed for this purpose. Equipment sensitive to voltage sags was tested using this generator. Overall, five types of sensitive equipment were tested: personal computers, fluorescent lamps, drives with speed control, programmable logic controllers, and contactors. The measured sensitivity curves of these devices have been used to determine the number of trips (failures due to voltage sags. Two probabilistic methods (general probability method and cumulative probability method to determine probability of equipment failure occurrence are used. These methods were applied to real node in the distribution system with its actual performance of voltage sags/swells. The calculations also contain different levels of sensitivity of the sensitive equipment.
Truppa, Walter A.; Rey, Hugo L.; Rojas, Carlos A.
The paper describes the way in which the Nuclear Regulatory Authority (ARN) has implemented an 'enforcement' policy for the services of radiotherapy that operated obsolete cobalt therapy units. Without doubt one of the greater advances has been the simulation and planning of the treatment, indispensable tools in a system of quality in radiotherapy where the equipment acquires a preponderant paper. In Argentina the distribution of equipment was inhomogeneous, and within it coexisted, as primary and unique units, great amount with a technology today already obsolete. The Nuclear Regulatory Authority (ARN) took a strong regulatory attitude directed to change or to retire many of the units, as its characteristics of design and antiquity did not fulfill the criteria of radiological security established in the norms (optimization of the dose, distances source to skin, yield in surface, adequate maintenance, etc.). On this matter a policy was applied to impose within suitable terms, the change of the obsolete equipment for this practice, particularly those distances source to skin minor than 80 cm. As result of the applied coercive measures at this moment, 28 equipment of cobalt therapy in advanced degree of obsolescence were retired by regulatory decision. Part of these equipment were replaced by their owners by more modern equipment whose operation adjusts to the requirements of the radiological security norm, whereas the majority was replaced by linear accelerators. At the moment there are 86 of cobalt therapy units and 52 accelerators operating in our country, against 104 and 32 respectively, that operated in 1995. (author)
Radio Netherlands Cooperation 42 NIGER Algerian Aid Praised by Minister (LE SAHEL, 19 Dec 77) 43 NIGERIA FMG Control of Radio Station To Be...USSR. He reported that the latest equipment, which provides for a high degree of automation in controlling intermediate stations with the aid of... Amazonas . There are problems with regard to production for the Center-East. First of all, there is a lack of criteria. "There is a certain half-nebulous
This report summarizes and analyses the work that have been carried out by the Transportation Equipment Manufacturing Sector (TEMS) Working Group of the National Climate Change Industry Table over the last 14 months, and presents the Group's view of appropriate policies for greenhouse gas emission reduction in Canada. To develop its approach, the Working Group conducted five separate studies which are included in this report as annexes. Annex A is a Foundation Paper, which provides an overview of the sector's performance vis-a-vis energy use and greenhouse gas production. Annex B analyzes the competitive position of the industry by reviewing growth trends in each of the industry sub-sectors and the key factors in maintaining and enhancing the sector's international competitive position. Annex C is a technology assessment. It provides an overview of the uptake of energy saving technology in the sector. Annex D provides a facility level analysis focusing on energy use in the automotive parts manufacturing sector. Annex E is a review of American policies on climate change, summarizing the approach currently being taken towards greenhouse gas emission reduction in the United States. Some of the key findings of this report are: (1) business-as-usual emissions will greatly exceed the implicit Kyoto target of six per cent reduction from 1990 levels, (2) relatively few opportunities exist for major emissions reductions through the use of existing technology, (3) sector-specific policies appear to be ill-advised, but cross-cutting policies provide good opportunities for the transportation equipment manufacturing sector to do its part in helping Canada meeting its Kyoto commitment. The report recommends investigation of barriers to adoption of new technologies and examination of market imperfections, promotion of cogeneration where it makes economic sense, and consideration of the use of flexible instruments such as carbon taxes and tradable emission permits. Overall, the
TELECOMMUNICATIONS, Sep 77) 54 PTT’s Social Action Policy Detailed (MESSAGES DES POSTES ET TELECOMMUNICATIONS, Sep 77) 58 GREECE Briefs...undertaken that are counter to state and social requirements for order and security. (5) If amateur radio stations of the GST are operated for...telephone (1)-567-70-97. 52 Reseaux eommutea Dibit (bHt/i) Liaisons specialities telex telephone Caducee TRANSPAC 50 200 1200 2400
... services. We seek comment on these trends and associated Commission policies. DATES: Comments are due on or... limit distribution in some fashion? Should the Commission permit these other entities to obtain only non... geography-based intercarrier compensation to bill-and-keep, focusing particularly on whether telephone...
operation with water injection per year. Figures 2. 114 USSR UDC 621.438:621.43:536.2 BALANCE OF ENERGY, HEAT AND EXERGY IN A DIESEL- TURBINE ...71 Turbine & Engine Design 86 EQUIPMENT Acoustical & Ultrasonic 91 Aeronautical & Space 93 Atomic & Nuclear 94 Gyros copic 95 Hydraulic...96 Industrial 98 Marine & Shipbuilding 101 Measuring, Testing, Calibrating 103 Power, Engine, Turbine , Pump 114 - a - [III - USSR - 21 F
On 16 March, eight days after International Women's Day, CERN is organizing a discussion on its Equal Opportunities Policy. This is a new chance for all at CERN to find out about the programme, and to get up to date with the position of women at CERN. This year CERN will mark International Women's Day with a special event on Friday 16 March: a chance for all at CERN to meet members of the Equal Opportunities Advisory Panel. You have probably already heard about the Panel, but you may have wondered what the Equal Opportunities Programme actually does to ensure fair treatment in the recruitment and career development of men and women, and to allow all to work in an atmosphere of safety, dignity, and mutual respect. Daniella Moraes of the Federal University of Rio de Janeiro at work on electronics for the LHCb experiment. By attending this meeting CERN people will have the chance to learn about the work of the Panel, its recommendations to Management, and the subsequent actions taken by the Organization. The m...
Barry W. Bobst; Joe T. Davis
Land use shifts between cropland and pasture affect the demand for beef cow inventories because economically viable cow-calf enterprises are pasture-based. Econometric analysis indicates an inverse relationship of −36.6 thousand head of beef cows per million acre change in harvested cropland. Curtailment of the expansion phase of the current cattle cycle and subsequent declines in cow numbers is in part attributable to large acreages converted from pasture to cropland in the early 1980s. Conv...
Gavurová, Beáta; Kováč, Viliam; Fedačko, Ján
This study aims to examine the localisation of selected parameters in the deployment and use of medical equipment in the Slovak Republic and to verify potential regional disparities. The study evaluates the benefits of an analytical platform for regulatory mechanisms in the healthcare system. The correspondence analysis is applied to the entire data set containing information regarding medical equipment distribution and mortality. The results highlight regional differences in the use of medical equipment throughout the analysed period from 2008 to 2014. The total amount of medical equipment increased slightly to 9192 devices during the time span. In 2014, there was a significant decrease of 16.44%. Disparities are found in the frequencies and structure of medical equipment. In some regions, medical equipment is not present or is present in low numbers. The results regarding regional disparities demonstrate the regional development of the amount of medical equipment. The deployment of medical equipment is not proportional, and not all of the analysed devices are available in each region. The tests also indicate the appropriateness of the amount of medical equipment and create a platform for further investigation. The results of the analysis suggest the unsuitable distribution of medical equipment throughout the Slovak regions, where there are significant regional disparities. These findings can serve as a monitoring platform to evaluate the accessibility and efficiency of medical equipment usage. No human participants were involved in the research.
Full Text Available Among numerous environmental challenges in the ASEAN region, the rapid growth of volumes of waste from electrical and electronic equipment (e-waste has increasingly drawn international attention. Economies face huge demands for electrical and electronic products, while governments are confronted with difficulties dealing with mounting volumes of e-waste. Furthermore, lucrative transnational shipment of discarded electric and electronic devices calls for a regional response to the issue. While ASEAN has failed to come up with a common policy response, certain member states have pushed ahead with their own legislation in an attempt to address this urgent issue. This study sets out to identify the determining factors which have disabled ASEAN in terms of agreeing on a common policy response in the case of dealing with e-waste. Based on the assumption that states act according to expected gains, the study applies a game theoretical approach to analyse the developments. ----- Die Bewältigung der rasant anwachsenden Menge an Elektroschrott zählt zu den großen umweltpolitischen Herausforderungen der ASEAN-Staaten. Während sich die Volkswirtschaften einer immer größer werdenden Nachfrage nach elektrischen und elektronischen Geräten gegenübergestellt sehen, vermögen es die meisten Länder nicht adäquate Entsorgungswege für Altgeräte aufzubauen. Zusätzlich zur inländischen Produktion gilt es auch mit oftmals als Gebrauchtprodukt getarntem, importiertem Elektroschrott umzugehen. Eine dringend notwendige regionale Koordinierung wurde von ASEAN noch nicht in Angriff genommen. Diese Studie geht der Frage nach, warum auf Ebene von ASEAN keine Lösungsansätze zu dieser Problematik zu erwarten sind. Zur Analyse der Entwicklungen bedient sich die Arbeit eines spieltheoretischen Ansatzes.
Four articles are gathered in this data sheet: they deal with 1) PAM's flow meter technology 2) ATHELIA traceability: a strategic challenge for the LPG market 3)A. SILVA MATOS changes its image and emerges into the energies 4) BLACKMER offers a full line of LPG equipment for the transfer of propane, butane and anhydrous ammonia. (authors)
Lazarus, Sheryl; Thurlow, Martha
Sound test security policies and procedures are needed to ensure test security and confidentiality, and to help prevent cheating. In this era when cheating on tests draws regular media attention, there is a need for thoughtful consideration of the ways in which possible test security measures may affect accessibility for some students with…
Department of Veterans Affairs — Number of life insurance policies for each administered life insurance program listed by state. Data is current as of 08/31/11. All programs are closed to new issues...
Norris, Susan L; Holmer, Haley K; Burda, Brittany U; Ogden, Lauren A; Fu, Rongwei
Conflict of interest (COI) of clinical practice guideline (CPG) sponsors and authors is an important potential source of bias in CPG development. The objectives of this study were to describe the COI policies for organizations currently producing a significant number of CPGs, and to determine if these policies meet 2011 Institute of Medicine (IOM) standards. We identified organizations with five or more guidelines listed in the National Guideline Clearinghouse between January 1, 2009 and November 5, 2010. We obtained the COI policy for each organization from publicly accessible sources, most often the organization's website, and compared those polices to IOM standards related to COI. 37 organizations fulfilled our inclusion criteria, of which 17 (46%) had a COI policy directly related to CPGs. These COI policies varied widely with respect to types of COI addressed, from whom disclosures were collected, monetary thresholds for disclosure, approaches to management, and updating requirements. Not one organization's policy adhered to all seven of the IOM standards that were examined, and nine organizations did not meet a single one of the standards. COI policies among organizations producing a large number of CPGs currently do not measure up to IOM standards related to COI disclosure and management. CPG developers need to make significant improvements in these policies and their implementation in order to optimize the quality and credibility of their guidelines.
Антон Юрьевич Петров
Full Text Available The article considers state import of industrial equipment in the context of the customs regulation of Russia’s foreign trade under S.Yu. Witte as the Minister of Finance (1892–1903. The analysis of archival data reveals the motives which drove various ministries of the Russian empire when they gave preference to foreign producers rather than domestic ones. In the 1890s the Ministry of Finance, on the one hand, and other ministries, on the other hand, were debating the necessity of orders for foreign industrial equipment made by the Russian governmental bodies. The article studies the course and results of this interdepartmental struggle.
Koomey, J.G.; Cramer, M.; Piette, M.A.; Eto, J.H.
This report describes a detailed end-use forecast of office equipment energy use for the US commercial sector. We explore the likely impacts of the US Environmental Protection Agency`s ENERGY STAR office equipment program and the potential impacts of advanced technologies. The ENERGY STAR program encourages manufacturers to voluntarily incorporate power saving features into personal computers, monitors, printers, copiers, and fax machines in exchange for allowing manufacturers to use the EPA ENERGY STAR logo in their advertising campaigns. The Advanced technology case assumes that the most energy efficient current technologies are implemented regardless of cost.
Dynamic programming was utilized as an alternative optimization technique to determine an optimal policy over a given time period. According to a joint effect of the probabilistic transition of states and the sequence of decision making, the optimal policy is sought such that a set of decisions optimizes the long-run expected average cost (or profit) per unit time. Provision of an alternative measure for the expected long-run total discounted costs is also considered. A computer program based on the concept of the Markov Decision Process was developed and tested. The program code listing, the statement of a sample problem, and the computed results are presented.
Medical technology is a fundamental instrument for the provision of health services in the Mexican Institute of Social Security (IMSS) and as a support for diagnostic and therapeutic interventions. The inventory of relevant medical equipment describes the needs for upgrading the technological infrastructure, organize its distribution and plan its renovation in order to guarantee the quality of health services. In this report we describe the type of equipment used in radiology and other imaging services, its geographical distribution, median age in operation and its productivity. The inventory reported 2091 pieces of equipment, ultrasonography and radiology were the most common types (31%) followed by fluoroscopic equipment (20%). Follow-up in the inventory should help in planning the acquisition and maintenance of sophisticated technology used for medical purposes.
Bryan, Jeffery D.
This white paper investigates the potential integration of the CTC work breakdown structure numbering scheme with a plant/equipment numbering system (PNS), or alternatively referred to in industry as a reference designation system (RDS). Ideally, the goal of such integration would be a single, common referencing system for the life cycle of the CTC that supports all the various processes (e.g., information, execution, and control) that necessitate plant and equipment numbers be assigned. This white paper focuses on discovering the full scope of Idaho National Laboratory (INL) processes to which this goal might be applied as well as the factors likely to affect decisions about implementation. Later, a procedure for assigning these numbers will be developed using this white paper as a starting point and that reflects the resolved scope and outcome of associated decisions.
Ackerman, Amy; Etow, Alexis; Bartel, Sara; Ribisl, Kurt M
Because higher density of tobacco retailers is associated with greater tobacco use, U.S. communities seek ways to reduce the density and number of tobacco retailers. This approach can reduce the concentration of tobacco retailers in poorer communities, limit youth exposure to tobacco advertising, and prevent misleading associations between tobacco and health messaging. Communities can reduce the density and number of tobacco retailers by imposing minimum distance requirements between existing retailers, capping the number of retailers in a given geographic area, establishing a maximum number of retailers proportional to population size, and prohibiting sales at certain types of establishments, such as pharmacies, or within a certain distance of locations serving youth. Local governments use direct regulation, licensing, or zoning laws to enact these changes. We analyze each approach under U.S. constitutional law to assist communities in selecting and implementing one or more of these methods. There are few published legal opinions that address these strategies in the context of tobacco control. But potential constitutional challenges include violations of the Takings Clause of the Fifth Amendment, which protects property owners from onerous government regulations, and under the Fourteenth Amendment's Equal Protection and Due Process Clauses, which protect business owners from arbitrary or unreasonable regulations that do not further a legitimate government interest. Because there is an evidentiary basis linking the density of tobacco retailers to smoking rates in a community, courts are likely to reject constitutional challenges to carefully crafted laws that reduce the number of tobacco retailers. Our review of the relevant constitutional issues confirms that local governments have the authority to utilize laws and policies to reduce the density and number of tobacco retailers in their communities, given existing public health data. The analysis guides policy
Hourieh, Shamshiri-Milani; Abolghasem, Pourreza; Feizollah, Akbari
Unsafe and illegal abortions are the third leading cause of maternal death. It affects physical, emotional and social health of women and their families. Abortion is a multi-dimensional phenomenon with several social, legal, and religious implications. The views of policy-makers affect the approach to abortion in every society. Understanding the attitudes and knowledge of high-ranking decision makers towards abortion was the purpose of this study. A qualitative research was implemented by carrying out individual interviews with 29 out of a selection of 80 presidents of medical sciences universities, senior executive managers in the legal system, forensic medicine and decision-makers in the health system and a number of top Muslim clerics, using a semi-structured questionnaire for data gathering. Content analysis revealed the results. There were considerable unwillingness and reluctance among the interviewees to participate in the study. The majority of participants fairly knew about the prevalence of illegal abortions and their complications. There was strong agreement on abortion when health of the mother or the fetus was at risk. Abortion for reproductive health reasons was supported by a minority of the respondents. The majority of them disagreed with abortion when pregnancy was the result of a rape, temporary marriage or out of wedlock affairs. Making decision for abortion by the pregnant mother, as a matter of her right, did not gain too much approval. It seemed that physical health of the mother or the fetus was of more importance to the respondents than their mental or social health. The mother's hardship was not any indication for induced abortion in the viewpoints of the interviewed policy-makers. Strengthening family planning programs, making appropriate laws in lines with religious orders and advocacy programs targeting decision makers are determined as strategies for improving women's health rights.
Aber, Lawrence; Morris, Pamela; Raver, Cybele
Now, more than ever, it is crucial to address the topic of children and poverty in the U.S., given current scientific knowledge about poverty's influence on children and effective strategies to mitigate its negative impact. In this report, we summarize the best available information on definitions and trends in child poverty, policy responses to…
Whiteman, Rodney S.; Shi, Dingjing; Plucker, Jonathan A.
This policy brief explores Senate Enrolled Act 001 (SEA 1), specifically the provisions for how teachers must be evaluated. After a short summary of SEA 1 and its direct changes to evaluation policies and practices, the brief reviews literature in teacher evaluation and highlights important issues for school corporations to consider when selecting…
Amos, Jason, Ed.
"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) Waiving Away High School Graduation Rate Accountability?: State NCLB Waiver Proposals Threaten to Weaken…
Amos, Jason, Ed.
"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) Problems Down the Road: House Passes Congressional Budget Resolutions, Sets Overall Spending Cap at $19 Billion Below Senate;…
Lazarus, Sheryl; Thurlow, Martha; Christensen, Laurene; Shyyan, Vitaliy
Federal policy initiatives such as the flexibility waivers for accountability are requiring that states transition away from the use of an alternate assessment based on modified achievement standards (AA-MAS). It is expected that those students who had participated in that assessment will instead participate in the state's general assessment (or a…
Alliance for Excellent Education, 2009
"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) Congress Begins Budget Debate: House and Senate Budget Plans Accommodate President Obama's Education Proposals; (2)…
Amos, Jason, Ed.
"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) State of the Union Preview: In Email to Supporters, Obama Highlights Economy and Jobs, Education, Deficit Reduction, and…
This monograph discusses policies designed to deal with food and nutrition problems in Tanzania. Available information on food supplies and nutritional conditions in Tanzania clearly shows that the country faces nutritional problems; protein energy malnutrition is the most serious and requires priority action. Iron deficiency anemia, goiter, and…
American Federation of Teachers, 2004
The Latino population is the fastest growing ethnic minority in the United States. This group is rapidly changing the face of public schools and presenting a unique set of challenges to public education. This policy brief provides the data and context to support the American Federation of Teacher's call for increased attention to the condition of…
Amos, Jason, Ed.
"Straight A's: Public Education Policy and Progress" is a biweekly newsletter that focuses on education news and events both in Washington, DC and around the country. The following articles are included in this issue: (1) Digital Learning Meets Digital Democracy: Alliance for Excellent Education Accepting Public Feedback on New Digital Learning…
Hope Ian A
Full Text Available Abstract Background Escherichia coli strain EL350 contains chromosomally integrated phage lambda Red recombinase genes enabling this strain to be used for modifying the sequence of resident clones via recombineering. BAC and fosmid clones are highly suitable for modification by recombineering but, because they are present at low (1-2 copies per cell, the DNA is difficult to isolate in high yield and purity. To overcome this limitation vectors, e.g. pCC1FOS, have been constructed that contain the additional replication origin, oriV, which permits copy-number to be induced transiently when propagated in a suitable host strain, e.g. EPI300, that supplies the cognate trans-replication protein TrfA. Previously, we used EL350 and EPI300 sequentially to recombineer oriV-equipped fosmid genomic clones and, subsequently, to induce copy-number of the resulting recombinant clone. To eliminate these intervening DNA isolation and transformation steps we retrofitted EL350 with a PBAD-driven trfA gene generating strain MW005 that supports, independently, both recombineering and copy-number induction. Results The PBAD-driven copy of cre in EL350 was replaced seamlessly with a copy of trfA, PCR-amplified from EPI300 chromosomal DNA, to generate MW005. This new strain has been used to both generate, via recombineering, a number of reporter gene fusions directly from pCC1FOS-based Caenorhabditis elegans genomic clones and to transiently induce copy-number of fosmid and BAC clones prior to DNA preparation. Conclusions By retrofitting EL350, an established 'recombineering' E. coli strain, with a tightly regulated copy of trfA we have produced a new strain, MW005, which combines recombineering capacity with the useful ability to transiently induce copy-number of oriV-equipped clones. By coupling these two steps in a single strain, use of MW005 will enable the more rapid recombineering-mediated production of recombinant clones in the yield and quality necessary for
Notten, Geranda; de Neubourg, Chris
Financial poverty indicators still play an important role in policymaking and evaluation. Countries such as the USA and the EU member states use one or several ‘official’ poverty indicators on which success of poverty reduction policy is regularly monitored. Whereas the US poverty indicator is based on an absolute concept of poverty, the EU Laeken indicator is based on a relative concept. But the consequences of such a decision are considerable. As absolute and relative poverty indicators ref...
Duscha, Markus; Seebach, Dominik
Research under contract with the German Federal Environmental Agency (UBA) identified a considerable energy saving potential fielding the area of office equipment. In this paper, a proposal for a policy mix is presented with the goal to increase energy efficiency by market-transformation in this sector. This was worked out by order of the UBA. Pending EU legislation like the Procurement Directive and the proposal for Eco-Design Directive have been considered. An in-depth analysis for labelling schemes for office equipment is provided with respect to the future of the Energy Star process, specifically the continuation of the Energy Star-cooperation between the U.S.EPA and the EU. Preliminary results gained after literature enquiry and interviews of experts were discussed during a workshop at the German Federal Environmental Ministry in September 2004. Our proposal for a policy mix includes: public procurement, efficiency labelling, training and education, energy management in public and private institutions, mandatory minimum standards, marketing. The demand for high efficient appliances should initially be boosted by green procurement to trigger market transformation. In the field of efficiency labelling, we first analyse the shortcomings of previous strategies. On this basis, we propose a two level-strategy for Germany: 1. The Energy Star process with improved structures shall act as a widely compliable labelling minimum standard. 2. An information programme about high efficient appliances ('quality-programme') should be established basing on existing structures (Energy Star, GEEA, TopTen) to minimise transaction costs
Buizer, I.M.; Lawrence, A.
Forestry worldwide has a history of relying upon quantification, drawing on science and economics to compute core concepts such as the relationship between tree-based stand descriptors and marketable timber volumes. This number-oriented approach is grounded in rationalisation and sustained yield
Li, Jinhui; Dong, Qingyin; Liu, Lili; Song, Qingbin
Waste Electrical and Electronic Equipment (WEEE) volume is increasing, worldwide. In 2011, the Chinese government issued new regulations on WEEE recycling and disposal, establishing a WEEE treatment subsidy funded by a levy on producers of electrical and electronic equipment. In order to evaluate WEEE recycling treatment costs and revenue possibilities under the new regulations, and to propose suggestions for cost-effective WEEE management, a comprehensive revenue-expenditure model (REM), were established for this study, including 7 types of costs, 4 types of fees, and one type of revenue. Since TV sets dominated the volume of WEEE treated from 2013 to 2014, with a contribution rate of 87.3%, TV sets were taken as a representative case. Results showed that the treatment cost varied from 46.4RMB/unit to 82.5RMB/unit, with a treatment quantity of 130,000 units to 1,200,000 units per year in China. Collection cost accounted for the largest portion (about 70.0%), while taxes and fees (about 11.0 %) and labor cost (about 7.0 %) contributed less. The average costs for disposal, sales, and taxes had no influence on treatment quantity (TQ). TQ might have an adverse effect on average labor and management costs; while average collection and purchase fees, and financing costs, would vary with purchase price, and the average sales fees and taxes would vary with the sales of dismantled materials and other recycled products. Recycling enterprises could reduce their costs by setting up online and offline collection platforms, cooperating with individual collectors, creating door-to-door collection channels, improving production efficiency and reducing administrative expenditures. The government could provide economic incentives-such as subsidies, low-cost loans, tax cuts and credits-and could also raise public awareness of waste management and environmental protection, in order to capture some of the WEEE currently discarded into the general waste stream. Foreign companies with
Rutkowski, David J.; Prusinski, Ellen L.
The staff of the Center for Evaluation & Education Policy (CEEP) at Indiana University is often asked about how international large-scale assessments influence U.S. educational policy. This policy brief is designed to provide answers to some of the most frequently asked questions encountered by CEEP researchers concerning the three most popular…
McDade, Mark [National Renewable Energy Lab. (NREL), Golden, CO (United States)
The Department of Energy/National Renewable Energy Laboratory (DOE/NREL) owns and operates a megawatt-scale dynamometer used for testing wind turbine drive trains up to 1.5 megawatt (MW) in rated capacity. At this time, this unit is the only unit of its type in the United States, available for use by the American Wind Industry. Currently this dynamometer is heavily backlogged and unavailable to provide testing needed by various wind industry members. DOE/NREL is in possession of two critical pieces of equipment that may be used to develop an alternative Dynamometer facility, but does not have the funds or other resources necessary to develop such a facility. The Participant possesses complimentary facilities and infrastructure that when combined with the NREL equipment can create such a test facility. The Participant is also committed to expending funds to develop and operate such a facility to the subsequent benefit of the Wind Industry and DOE Wind Energy program. In exchange for DOE/NREL providing the critical equipment, the Participant will grant DOE/NREL a minimum of 90 days of testing time per year in the new facility while incurring no facilities fees.
This December 2012 Brief updates NSCC's 2011 report "State Policies on School Climate and Bully Prevention Efforts: Challenges and Opportunities for Deepening State Policy Support for Safe and Civil School"s (www.schoolclimate.org/climate/papers-briefs.php). This Brief provides a summary of State level: (1) anti-bullying legislation; (2)…
Research Ethics has emerged as one of the most well-developed policy areas within the sphere of Research and Innovation Management. As such, for African institutions looking to strengthen their policy frameworks, develop increased collaborations, and increase research outputs, a thorough understanding of global trends in Ethics will be vital.…
Spradlin, Terry; Cierniak, Katherine; Shi, Dingjing; Chen, Minge
This Education Policy Brief summarizes the research and data analysis completed by the Center for Evaluation and Education Policy (CEEP) on Indiana's student attendance and absenteeism data. The study was initiated by The Indiana Partnerships Center and conducted by CEEP with funding from USA Funds and State Farm. Additional partners in the study…
Spradlin, Terry; Gard, Greta; Huang, Vivian; Kopp, Beth; Malik, Alanna
This Education Policy Brief examines the latest research and statistics regarding childhood obesity. In addition to providing an overview of current trends and effects of childhood obesity, this brief considers the reasons for the increase in obesity rates among children, as well as the latest federal and state initiatives created to combat…
Cross, Christopher T.
Over the course of our nation's existence, the federal role in K-12 education has evolved many times. From an initial limited role to one that is more focused today on access and equity, the federal role in education policy has seldom been without controversy. During each twist and turn there has been ongoing debate over federal versus state…
This issue of ETS Policy Notes (Vol. 20, No. 4) provides highlights from the symposium, "Middle School Matters: Improving the Life Course of Black Boys" held on July 23-24, 2012. The second in a series of four symposia co-sponsored by ETS and the Children's Defense Fund (CDF), the seminar examined the education and status of…
Newman, Constance; Guthrie, Joanne; Mancino, Lisa; Ralston, Katherine; Musiker, Melissa
Concerns about child obesity have raised questions about the quality of meals served in the National School Lunch Program. Local, State, and Federal policymakers responded to these concerns beginning in the mid-1990s by instituting a range of policies and standards to improve the quality of U.S. Department of Agriculture-subsidized meals. Schools…
The federal government has made a policy choice to share Free Application for Federal Student Aid (FAFSA) information with colleges. This arrangement has been viewed as an administrative detail by students, parents, policymakers, and even economists. The results of this study demonstrate that this seemingly unimportant administrative detail is…
American Federation of Teachers, 2002
This policy brief provides the context and the research supporting the American Federation of Teacher's call for universal early childhood education. It focuses on the current challenges the nation faces in achieving such a program; and it includes the signs of progress, a description of what other industrialized countries are doing, the features…
Millei, Zsuzsa; Gallagher, Jannelle
Australian early childhood education still labours with the achievement of universal access and the production of comprehensive and consistent data to underpin a national evidence base. In this article, we attend to the processes led by numbers whereby new practices of quantification, rationalization and reporting are introduced and mastered in a…
Experimental Housing Planning): "Com- parative Evaluation of Domestic Concrete-Mixture Superplasticizers "] [Text] The concrete-mix plasticizers...setting and hardening of the ce- ment stone, leading to reduced strength if the steaming procedure is not changed. The superplasticizers (SP), a new... superplasticizers (S-3, NIL-10, KOD-S combined with NN potassium nitrite, GPD combined with NNKhK calcium chloride nitrate-nitrite, and SDB) on the
Almeida, Claudio C. de; Cambises, Paulo B.S.; Paiva, Julio E. de; Paiva, Julio E. de; Silva, Teresina M.; Rodrigues, Demerval L.
This paper presents the steps adopted in the operation planned for the decontamination of surfaces in the old storage shed number 99 the general layout of the Energy Research and Nuclear IPEN-CNEN/SP, Brazil, and contained various types of equipment originating from production hexafluoride natural uranium (UF6). This operation involved the planning, training of operators of the facility, analysis of workplaces and radiometric surveys for monitoring of external radiation and surface contamination. The training involved the procedures for decontamination of surfaces, segregation of materials and practical procedures for individual monitoring of contamination outside of the body. Were also established rules for the transport of radioactive materials in the internal and external facility and release of material and sites already decontaminated
Hermawan; Suprapto, M.; Setyawan, A.
Rehabilitation and maintenance of road performed by technical agencies at the local government in Indonesia, are generally not based on the assessment of road conditions. The value of the structural and functional condition of the pavement is not counted on carefully. As a result, road rehabilitation and maintenance patterns tend to be similar, repetitive and improper. International Roughness Index (IRI) is a parameter for assessing the functional condition of the pavement while the Structural Number (SN) is a parameter for assessing the structural condition of the pavement. Measuring road conditions by using Roadroid applications on smartphones can provide an efficient way, scalable, and low cost to the highway authority to collect road condition data. This study was conducted to determine the conditions of the road both functionally and structurally. Results of research conducted, pavement functionally in a good condition with the acquisition of IRI value of less than 4. Structural pavement conditions indicate that the value of Structural Number Effective (SNeff) is less than the value of the Structural Number Future (SNf), thus the structural condition of the road segments has not been able to serve traffic with a design life of 20 years. Prediction of IRI value obtained to determine the type of road maintenance is functionally performed when the value of IRI exceeds the value of 4 with an overlay of material HRS WC 30 mm. Structurally road maintenance carried out various scenarios, the phased construction and direct construction. The type of material and thickness of pavement on a phased construction scenario for the design life of 15-20 years and direct construction gives better results than the phased construction scenarios for the design life of 5-20 years and 10-20 years.
In accordance with the requirements of Section 113(b)(3) of the Nuclear Waste Policy Act of 1982 (NWPA), as amended, the US Department of Energy has prepared this report on the progress of site characterization activities at Yucca Mountain, Nevada, for the period April 1 through September 30, 1990. This report is the third of a series of reports that are issued at intervals of approximately six months during site characterization. The report covers a number of new initiatives to improve the effectiveness of the site characterization program and covers continued efforts related to preparatory activities, study plans, and performance assessment. 85 refs., 2 figs., 3 tabs.
Fernandes Más, Heyd
What are the legal instruments and policy choices producing improvements in e-waste management strategies worldwide? Could they be used from one legal system to another? The EU’s tradition of focusing on waste management and setting goals and responsibilities for all stakeholders involved in
Vitharana, V. H. P.; Chinda, T.
Lower back pain (LBP), prevalence is high among the heavy equipment operators leading to high compensation cost in the construction industry. It is found that proper training program assists in reducing chances of having LBP. This study, therefore aims to examine different safety related budget available to support LBP related training program for different age group workers, utilizing system dynamics modeling approach. The simulation results show that at least 2.5% of the total budget must be allocated in the safety and health budget to reduce the chances of having LBP cases.
When an operator hears sounds in a plantsite, the operator compares normal sounds of equipment which he previously heard and remembered with sounds he actually hears, to judge if they are normal or abnormal. According to the method, there is a worry that abnormal conditions can not be appropriately judged in a case where the number of objective equipments is increased and in a case that the sounds are changed gradually slightly. Then, the device of the present invention comprises a plurality of monitors for monitoring the operation sound of equipments, a recording/reproducing device for recording and reproducing the signals, a selection device for selecting the reproducing signals among the recorded signals, an acoustic device for converting the signals to sounds, a switching device for switching the signals to be transmitted to the acoustic device between to signals of the monitor and the recording/reproducing signals. The abnormality of the equipments can be determined easily by comparing the sounds representing the operation conditions of equipments for controlling the plant operation and the sounds recorded in their normal conditions. (N.H.)
The European Common Fisheries Policy (CFP) is a common policy that originates from 1983 and has been renewed every 10 years. The policy generally aims for sustainable fisheries in terms of living resources, economics and social aspects. The most recent version of the policy was agreed in co-decision
... of Labor GRANTS AND AGREEMENTS WITH INSTITUTIONS OF HIGHER EDUCATION, HOSPITALS, AND OTHER NON-PROFIT... equipment. (ii) Manufacturer's serial number, model number, Federal stock number, national stock number, or... reported to the General Services Administration by DOL to determine whether a requirement for the equipment...
Full Text Available Abstract Background Treatments for coronary heart disease (CHD have evolved rapidly over the last 15 years with considerable change in the number and effectiveness of both medical and surgical treatments. This period has seen the rapid development and uptake of statin drugs and coronary artery revascularization procedures (CARPs that include Coronary Artery Bypass Graft procedures (CABGs and Percutaneous Coronary Interventions (PCIs. It is difficult in an era of such rapid change to accurately forecast requirements for treatment services such as CARPs. In a previous paper we have described and outlined the use of a Markov Monte Carlo simulation model for analyzing and predicting the requirements for CARPs for the population of Western Australia (Mannan et al, 2007. In this paper, we expand on the use of this model for forecasting CARPs in Western Australia with a focus on the lack of adequate performance of the (standard model for forecasting CARPs in a period during the mid 1990s when there were considerable changes to CARP technology and implementation policy and an exploration and demonstration of how the standard model may be adapted to achieve better performance. Methods Selected key CARP event model probabilities are modified based on information relating to changes in the effectiveness of CARPs from clinical trial evidence and an awareness of trends in policy and practice of CARPs. These modified model probabilities and the ones obtained by standard methods are used as inputs in our Markov simulation model. Results The projected numbers of CARPs in the population of Western Australia over 1995–99 only improve marginally when modifications to model probabilities are made to incorporate an increase in effectiveness of PCI procedures. However, the projected numbers improve substantially when, in addition, further modifications are incorporated that relate to the increased probability of a PCI procedure and the reduced probability of a CABG
Mannan, Haider R; Knuiman, Matthew; Hobbs, Michael
Treatments for coronary heart disease (CHD) have evolved rapidly over the last 15 years with considerable change in the number and effectiveness of both medical and surgical treatments. This period has seen the rapid development and uptake of statin drugs and coronary artery revascularization procedures (CARPs) that include Coronary Artery Bypass Graft procedures (CABGs) and Percutaneous Coronary Interventions (PCIs). It is difficult in an era of such rapid change to accurately forecast requirements for treatment services such as CARPs. In a previous paper we have described and outlined the use of a Markov Monte Carlo simulation model for analyzing and predicting the requirements for CARPs for the population of Western Australia (Mannan et al, 2007). In this paper, we expand on the use of this model for forecasting CARPs in Western Australia with a focus on the lack of adequate performance of the (standard) model for forecasting CARPs in a period during the mid 1990s when there were considerable changes to CARP technology and implementation policy and an exploration and demonstration of how the standard model may be adapted to achieve better performance. Selected key CARP event model probabilities are modified based on information relating to changes in the effectiveness of CARPs from clinical trial evidence and an awareness of trends in policy and practice of CARPs. These modified model probabilities and the ones obtained by standard methods are used as inputs in our Markov simulation model. The projected numbers of CARPs in the population of Western Australia over 1995-99 only improve marginally when modifications to model probabilities are made to incorporate an increase in effectiveness of PCI procedures. However, the projected numbers improve substantially when, in addition, further modifications are incorporated that relate to the increased probability of a PCI procedure and the reduced probability of a CABG procedure stemming from changed CARP preference
Conn-Powers, Michael; Cross, Alice F.; Zapf, Jason S.
In this Education Policy Brief, Indiana University's Center for Evaluation and Education Policy and Indiana Institute on Disability and Community tackle major policy questions regarding publicly-funded prekindergarten programs: Why should Indiana invest in prekindergarten? Who should be served? What should prekindergarten look like in Indiana? And…
Equipment usually used in water exercise programs is designed for variety, intensity, and program necessity. This guide discusses aquatic equipment under the following headings: (1) equipment design; (2) equipment principles; (3) precautions and contraindications; (4) population contraindications; and (5) choosing equipment. Equipment is used…
... (Continued) GENERAL SERVICES ADMINISTRATION Regional Offices-General Services Administration 72-UNIFORM ADMINISTRATIVE REQUIREMENTS FOR GRANTS AND AGREEMENTS WITH INSTITUTIONS OF HIGHER EDUCATION, HOSPITALS, AND OTHER... the equipment. (ii) Manufacturer's serial number, model number, Federal stock number, national stock...
This report describes the methodology applied in selecting equipment in the special safety systems for equipment qualification in the CANDU 600 MW nuclear generating stations at Gentilly 2 and Point Lepreau. Included is an explanation of the selection procedure adopted and the rationale behind the criteria used in identifying the equipment. The equipment items on the list have been grouped into three priority categories as a planning aid to AECB staff for a review of the qualification status of the special safety systems
Full Text Available The Department of National Defence made some progress in procurement in 2016 despite obstacles that included a continued drop in spending, the advent of a new federal Liberal government and uncertainty over the outcome of the Defence Policy Review. Four trends affected defence acquisitions in 2016. These include an ongoing slippage in recapitalizing the Canadian Armed Forces, some encouraging moves made on the shipbuilding and fighter jet files, mixed progress on implementing the 2014 Defence Procurement Strategy, and uncertainty over the Defence Policy Review. It is also too early to tell how the Trudeau government’s Policy on Results, known as the “deliverology” approach, will play out for defence procurement. However, Budget 2016’s major focus was not on defence, and it shifted some funding for capital equipment to a new endpoint of 2045. This suggests that delay in the overall defence procurement program continues. While the Liberals kept their pledge to make investment in the Royal Canadian Navy a priority, they also made good last year on a negative promise – not to purchase the F-35 stealth fighter bomber. However, further slowing things is the Liberals’ refusal to launch a competition to replace it until the Defence Policy Review is published. The government has made this situation more fraught with its intention to buy 18 Boeing Super Hornet fighter jets as interim aircraft, since Liberal policy requires the Royal Canadian Air Force to be capable of meeting both NORAD’s and NATO’s operational needs simultaneously. Prior to the release of the new defence policy, both the interim and permanent fighter aircraft projects lacked adequate funding. They were among several large projects that have been approved, but have not yet moved to the contract stage, and whose budgets were inadequate to move forward. Adding to this mix is the fact that a government-wide effort initiated in 2014 to streamline the defence procurement
Teerawattananon, Yot; Russell, Steve
This paper presents qualitative findings from an assessment of the acceptability of using economic evaluation among policy actors in Thailand. Using cost-utility data from two economic analyses a hypothetical case scenario was created in which policy actors had to choose between two competing interventions to include in a public health benefit package. The two competing interventions, laparoscopic cholecystectomy (LC) for gallbladder disease versus renal dialysis for chronic renal disease, were selected because they highlighted conflicting criteria influencing the allocation of healthcare resources. Semi-structured interviews were conducted with 36 policy actors who play a major role in resource allocation decisions within the Thai healthcare system. These included 14 policy makers at the national level, five hospital directors, ten health professionals and seven academics. Twenty six out of 36 (72%) respondents were not convinced by the presentation of economic evaluation findings and chose not to support the inclusion of a proven cost-effective intervention (LC) in the benefit package due to ethical, institutional and political considerations. There were only six respondents, including three policy makers at national level, one hospital director, one health professional and one academic, (6/36, 17%) whose decisions were influenced by economic evaluation evidence. This paper illustrates limitations of using economic evaluation information in decision making priorities of health care, perceived by different policy actors. It demonstrates that the concept of maximising health utility fails to recognise other important societal values in making health resource allocation decisions.
Full Text Available Abstract Background This paper presents qualitative findings from an assessment of the acceptability of using economic evaluation among policy actors in Thailand. Using cost-utility data from two economic analyses a hypothetical case scenario was created in which policy actors had to choose between two competing interventions to include in a public health benefit package. The two competing interventions, laparoscopic cholecystectomy (LC for gallbladder disease versus renal dialysis for chronic renal disease, were selected because they highlighted conflicting criteria influencing the allocation of healthcare resources. Methods Semi-structured interviews were conducted with 36 policy actors who play a major role in resource allocation decisions within the Thai healthcare system. These included 14 policy makers at the national level, five hospital directors, ten health professionals and seven academics. Results Twenty six out of 36 (72% respondents were not convinced by the presentation of economic evaluation findings and chose not to support the inclusion of a proven cost-effective intervention (LC in the benefit package due to ethical, institutional and political considerations. There were only six respondents, including three policy makers at national level, one hospital director, one health professional and one academic, (6/36, 17% whose decisions were influenced by economic evaluation evidence. Conclusion This paper illustrates limitations of using economic evaluation information in decision making priorities of health care, perceived by different policy actors. It demonstrates that the concept of maximising health utility fails to recognise other important societal values in making health resource allocation decisions.
Stein, R.R.; Martin, T.W.
The word in longwall components is big, and these larger components have price tags to match. The logic behind the greater investment is that it will yield high production rates and good uptime statistics. This is true in most cases. More important than single-shift tonnage records, average shift production continues to climb upwards. This paper reports on the quality, and more significantly, the quantity of service supplied for long-wall equipment, which has reached levels that would have been seen as unachievable when longwall mining was first introduced in the U.S. The school of thought then was that longwall would increase productivity in part by reducing the number of production units and thus reducing the number of personnel employed underground. The expectation of fewer employees turned out to be unrealistic. That was probably one reason that some early attempts to install longwall system looked more like failures than vision of the future
... DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL ADMINISTRATION UNIFORM ADMINISTRATIVE REQUIREMENTS FOR AWARDS AND SUBAWARDS TO INSTITUTIONS OF HIGHER EDUCATION, HOSPITALS, OTHER NONPROFIT ORGANIZATIONS, AND... following information: (i) A description of the equipment; (ii) Manufacturer's serial number, model number...
Study of the use of personal equipment in low coal. Experiments on personal equipment for low seam coal miners: II. Dexterity, protection and performance with padded gloves. Phase II report, number 2. Open file report 1 Jan 79-1 Sep 79
Krohn, G.; Sanders, M.; Volkmer, K.; Wick, D.; Miller, H.
The objective of this study was to determine the optimal personal equipment design for use in low coal based on ergonomic, biomechanic, and safety considerations. This report investigates the effects of adding a layer of extra padding to the palm area of leather gloves typically worn by low seam coal miners.
This Instruction establishes policies, responsibilities, and procedures for the procurement of goods and services to include supplies, equipment, publications, furniture, and information technology...
... WITH INSTITUTIONS OF HIGHER EDUCATION, HOSPITALS, AND OTHER NON-PROFIT ORGANIZATIONS Post-Award... serial number, model number, Federal stock number, national stock number, or other identification number... agency, the availability of the equipment shall be reported to the General Services Administration by the...
Fujie, M. [Hitachi Ltd., Tokyo (Japan)
As for high-elderly society, Japan is going to face in near future, self dependency without depending on others as far as possible of bed ridden people or people using wheel chair and also including the probable elderly ones is going to be necessary. In Japan, there is so far accumulation of high level mechatronics technology and it is thought that there is possible to develop a system to fulfill such needs. In this system, equipment has deep connection with human being and natural coexistence between the equipment and human being is most necessary. Accordingly, development and practical use of walking practicing machine used for elderly people, walking support system, daily life work support system and so forth are expected by making successful in practice the coexistence functions of high level robot/mechatronics technology and machine/man. However, the study regarding the technology that are common to man and machine, particularly, research of mental characteristics and physical characteristics of human being is still insufficient and further results are expected. 9 refs., 12 figs.
Study of the use of personal equipment in low coal. Experiments on personal equipment for low seam coal miners: VI. Comparison bumping hazards with high and low profile helmets. Phase II report, number 6. Open file report 1 Jan 79-1 Sep 79
Sanders, M.; Wick, D.; Krohn, G.
The objective of this study was to determine optimal personal equipment design for use in low coal based on ergonomic, biomechanic, and safety considerations. This report describes an experiment that was conducted to compare the relative bumping hazards of a low- and high-profile hard hat (helmet) in a low seam mining environment. The study was specifically designed to assess the effect of lowering the helmet profile on frequency of head impacts.
Study of the use of personal equipment in low coal. Experiments on personal equipment for low seam coal miners: IV. Incorporating coiled cord into cap lamp battery cords. Phase II report number 4. Open file report 1 Jan 79-1 Sep 79
Blake, T.; Sanders, M.; Krohn, G.; Wick, D.; Volkmer, K.
The objective of this study was to determine optimal personal equipment design for use in low coal based on ergonomic, biomechanic, and safety considerations. This report describes a study designed to evaluate a proposed modification in the cap lamp battery cord intended to reduce the incidence of snagging and catching of the cord. A three-phase evaluation was performed comparing a prototype with the standard, currently available cord.
von Kuster, Thomas, Jr.
Results from the first federally sponsored study of the chiropractic health care profession are presented, and a broad range of facts and issues of concern to policy-makers, the profession, and the public are described. The two-year project included three national surveys of: service providers (doctors of chiropractic in practice more than two…
After a definition of intervention, problems encountered for working in an adverse environment are briefly analyzed for development of various remote handling equipments. Some examples of existing equipments are given [fr
Graf, J.J.; Farny; Destot; Campan; Sabrie
This article gives an information as complete as possible about the activities of the French nuclear industry on the export market. It describes the equipment and services available in the field of research equipement and installations [fr
Study of the use of personal equipment in low coal. Experiments on personal equipment for low seam coal miners: I. Comparison of 10/60 and standard self-rescue devices. Phase II report, number 1. Open file report 1 Jan 79-1 Sep 79
Sanders, M.; Krohn, G.; Volkmer, K.; Wick, D.; Miller, H.
The objective of this study was to determine optimal personal equipment design for use in low coal based on ergonomic, biomechanic, and safety considerations. This report compares a proposed 10/60 'piggyback' 02-generating, self-rescue unit with the standard CO self-rescue unit with respect to work task interference. A simulated low seam coal mine was constructed and workers performed locomotion, shoveling, cart pushing, and timbering tasks with the 10/60 and standard self-rescue units attached to their belts.
Study of the use of personal equipment in low coal. Experiments on personal equipment for low seam coal miners: II. Effect of size and weight of battery pack on performance. Phase II report, number 3. Open file report 1 Jan 79-1 Sep 79
Sanders, M.; Krohn, G.; Wick, D.; Volkmer, K.; Beith, B.
The objective of this study was to determine optimal personal equipment design for use in low coal based on ergonomic, biomechanic, and safety considerations. This report describes three experiments that were conducted to determine the effects of size and weight of battery packs. The first experiment tested the sensitivity of task measures; that is, workers performed locomotion, shoveling, cart pushing, and timbering tasks to detect variations in the size and weight of battery packs. The second experiment focused on locomotion tasks and tested the effects of varying size and weight on task completion time. The third experiment compared the battery pack presently in use with a radically different configuration of power cells.
Study of the use of personal equipment in low coal. Experiments on personal equipment for low seam coal miners: V. Effect of reflectorized outer garments on detection and conspicuity of miners. Phase II report, number 5. Open file report 1 Jan 79-1 Sep 79
Beith, B.; Sanders, M.
The objective of this study was to determine optimal personal equipment design for use in low coal based on ergonomic, biomechanic, and safety considerations. This report details a study that was designed to assess the effect of retroreflective material on the detection and form recognition of workers in a mining environment. The study involves a one-fifth-scale simulation of the perceptual task found in underground low seam coal mines. Under this simulation, different configurations of retroreflective material are examined in various body positions at three different locations in the visual field.
Shackelford, Linda; Valle, Paul
Load Bearing Equipment for Neutral Buoyancy (LBE-NB) is an exercise frame that holds two exercising subjects in position as they apply counter forces to each other for lower extremity and spine loading resistance exercises. Resistance exercise prevents bone loss on ISS, but the ISS equipment is too massive for use in exploration craft. Integrating the human into the load directing, load generating, and motion control functions of the exercise equipment generates safe exercise loads with less equipment mass and volume.
... REQUIREMENTS FOR GRANTS AND AGREEMENTS WITH INSTITUTIONS OF HIGHER EDUCATION, HOSPITALS, AND OTHER NON-PROFIT... property. (ii) Manufacturer's serial number, model number, Federal stock number, national stock number, or... Services Administration by the DoD Component to determine whether a requirement for the equipment exists in...
The Analysis Of The Effects Of Regulatory Policy Finance Minister Number 91 In 2015 On The Factors That Influence The Willingnes To Pay Taxes Case Study On The Personal Tax Payers Registered In STO Jember
Full Text Available This research aims to analyze the Regulatory Policy of The Republic Indonesian PMKRI Number 91 in 2015 on Factors Affecting Tax Payer Willingness. This research is a kind of quantitative research using descriptive statistical approach.. this study uses the object in the form of personal tax payers registered in the tax office primary jember by questionnaire method. Sampling technique in this research is technique of Convinience Sampling. the sample used in this study are as many as 100 Individual Tax Payers who report the Annual SPT on 22 February to 30 March 2016 manually in KPP Pratama Jember. The results showed that the Regulatory Policy of The Republic Indonesian PMKRI Number 91 in 2015 has given a significant effect on the factors that influence the willingness to pay taxes that pay taxes awareness knowledge and understanding of the tax laws as well as good perception on the effectiveness of the tax system..
Chinda, Thanwadee; Ammarapala, Veeris; Suanmali, Suthathip
The construction industry involves many hazardous activities that may expose workers to a wide variety of health hazards. Selection of construction safety equipment is crucial in ensuring workers' safety. This article aims to examine key factors influencing management decisions concerning safety equipment selection, utilizing exploratory factor analysis (EFA) and the analytic hierarchy process (AHP). A questionnaire survey is conducted in the construction companies in Bangkok, Thailand. The factor analysis extracts 103 sets of data into six key factors - namely supplier agreements, supplier support, personal, equipment design, safety-related policies and cost value factors - with a total of 20 associated items. The AHP results conclude that the safety-related policies, equipment design and personal factors are the most important factors when selecting construction safety equipment. A construction company can use the study results as a checklist to help assess different safety equipment, and to select the best equipment.
Regulatory agencies require numbers to provide health protection. The manner in which these numbers are derived from animal experiments and human epidemiology is considered together with the limitations and inadequacies of these numbers. Some recent examples of risk assessment in Canada are given including asbestos, drinking water, and indoor air quality. The value of these numbers in providing a measure of the hazard in a wider perspective is stressed, although they can never be the sole determinant of public policy.
Cotelo, Elena D.
Since Uruguay did not have an study on X-ray equipment, students of Radiation Protection course (RP) made this field work throughout the country. The objective is to obtain information on the number and kind of X-ray radiodiagnostic equipment. Some of the results are: there are 666 radiodiagnostic equipment. The ratio of population to equipment is 4.515 to 1 in the capital and the mean rate in the rest of the country is 4.383 to one, with a minimum of 1.707 and a maximum of 8.220. The Public Health Ministry (MSP) and the Instituciones de Asistencia Medica Colectiva (a kind of private heath assurance) (IAMC) have less equipment in the capital than in the rest of the country. The 37% of the capital population receives assistance through the IAMC , with a 42.5 % of the equipment. Uruguay except the capital has 18 districts and 17 computed tomography equipment, from which only 3 belong to the MSP. Five districts do not have any. In Montevideo, there are 11.500 females over forty years of age per X-ray mammography equipment, and this relation in the rest of the country is 13.900. There are 21 X-ray Interventional radiology equipment, 16 of them are in the capital. Is from relating the radiodiagnostic equipment, the population and the procedures, that quality assistance indicators emerge. This owns high importance on the way to create a RP National Programme. (author)
Kim, Hak Seon; Lee, Sang Mok
The contents of this book are introduction of data communication on definition, purpose and history, information terminal about data communication system and data transmission system, data transmit equipment of summary, transmission cable, data port, concentrator and front-end processor, audio communication equipment like phones, radio communication equipment of summary on foundation of electromagnetic waves, AM transmitter, AM receiver, FM receiver and FM transmitter, a satellite and mobile communication equipment such as earth station, TT and C and Cellular phone, video telephone and new media apparatus.
Willson, Keith; Tabakov, Slavik
Know What to Expect When Managing Medical Equipment and Healthcare Technology in Your Organization As medical technology in clinical care becomes more complex, clinical professionals and support staff must know how to keep patients safe and equipment working in the clinical environment. Accessible to all healthcare professionals and managers, Medical Equipment Management presents an integrated approach to managing medical equipment in healthcare organizations. The book explains the underlying principles and requirements and raises awareness of what needs to be done and what questions to ask. I
Bayuk, nifer L; Rohmeyer, l; Sachs, cus; Schmidt, frey; Weiss, eph
This book is a taxonomy and thesaurus of current cybersecurity policy issues, including a thorough description of each issue and a corresponding list of pros and cons with respect to identified stances on each issue. It documents policy alternatives for the sake of clarity with respect to policy alone, and dives into organizational implementation issues. Without using technical jargon, the book emphasizes the importance of critical and analytical thinking when making policy decisions. It also equips the reader with descriptions of the impact of specific policy ch
Khan, T.A.; Baum, J.W.; Beckman, M.C.
This document contains information dealing with the lessons learned from the experience of nuclear plants. In this issue the authors tried to avoid the 'tyranny' of numbers and concentrated on the main lessons learned. Topics include: filtration devices for air pollution abatement, crack repair and inspection, and remote handling equipment
This article details the interface transfer of heavy-duty face equipment from 5's to 6's face in the Great Row Seam at Silverdale Colliery, British Coal, Western Area. The salvaged face was roofbolted using leg-mounted Wombat drilling rigs. All heavy-duty equipment was transported by FSV's. 5 figs.
A. Kristensen, Anders Schmidt
Cooling of electronic equipment is studied. The design size of electronic equipment decrease causing the thermal density to increase. This affect the cooling which can cause for example failures of critical components due to overheating or thermal induced stresses. Initially a pin fin heat sink...
Batterham, Robert L.; Fraser, K.I.
This paper reviews the literature on the optimal replacement of capital equipment, especially farm machinery. It also considers the influence of taxation and capital rationing on replacement decisions. It concludes that special taxation provisions such as accelerated depreciation and investment allowances are unlikely to greatly influence farmers' capital equipment replacement decisions in Australia.
, therefore, conducted as ... hoped that the outcome of this audit will help our health policy makers to prioritize equipment supply for ... studies were approved by the ethical committee of the. University of Uyo Teaching Hospital.
Haigh, William E.
Presents an activity, suitable for students in grades 6-12, on generating random numbers. Objectives, equipment needed, list of prerequisite experiences, instructional strategies, and ready-to-copy student worksheets are included. (JN)
... equipped and/or used for scientific research, testing, or analysis, except clinical laboratories operating... 41 Public Contracts and Property Management 2 2010-07-01 2010-07-01 true Laboratory and research...-General Policies § 101-25.109 Laboratory and research equipment. (a) This section prescribes controls for...
... 41 Public Contracts and Property Management 2 2010-07-01 2010-07-01 true Materials handling...-Replacement Standards § 101-25.405 Materials handling equipment. (a) Materials handling equipment will not be... materials handling equipment in storage, one month in storage equals 50 hours of operation. (ii) The number...
Analysis of licensed South African diagnostic imaging equipment. ... Pan African Medical Journal ... Introduction: Objective: To conduct an analysis of all registered South Africa (SA) diagnostic radiology equipment, assess the number of equipment units per capita by imaging modality, and compare SA figures with published ...
Ginsberg, Gerald L
The last twenty years have seen major advances in the electronics industry. Perhaps the most significant aspect of these advances has been the significant role that electronic equipment plays in almost all product markets. Even though electronic equipment is used in a broad base of applications, many future applications have yet to be conceived. This versatility of electron ics has been brought about primarily by the significant advances that have been made in integrated circuit technology. The electronic product user is rarely aware of the integrated circuits within the equipment. However, the user is often very aware of the size, weight, mod ularity, maintainability, aesthetics, and human interface features of the product. In fact, these are aspects of the products that often are instrumental in deter mining its success or failure in the marketplace. Optimizing these and other product features is the primary role of Electronic Equipment Packaging Technology. As the electronics industry continues to pr...
Wang, Binseng; Furst, Emanuel; Cohen, Ted; Keil, Ode R; Ridgway, Malcolm; Stiefel, Robert
Clinical engineering professionals need to continually review and improve their management strategies in order to keep up with improvements in equipment technology, as well as with increasing expectations of health care organizations. In the last 20 years, management strategies have evolved from the initial obsession with electrical safety to flexible criteria that fit the individual institution's needs. Few hospitals, however, are taking full advantage of the paradigm shift offered by the evolution of joint Commission standards. The focus should be on risks caused by equipment failure, rather than on equipment with highest maintenance demands. Furthermore, it is not enough to consider risks posed by individual pieces of equipment to individual patients. It is critical to anticipate the impact of an equipment failure on larger groups of patients, especially when dealing with one of a kind, sophisticated pieces of equipment that are required to provide timely and accurate diagnoses for immediate therapeutic decisions or surgical interventions. A strategy for incorporating multiple criteria to formulate appropriate management strategies is provided in this article.
industry as an example. Bertrand and Bookbinder begin with a basic supply chain logistics model of a large warehouse supplying a number of retail...solutions, and perform fast sensitivity analysis on the competing objectives. 14. SUBJECT TERMS Optimization, Marine Forces Reserve, redistribution...reallocation, equipment supply , logistics 15. NUMBER OF PAGES 61 16. PRICE CODE 17. SECURITY CLASSIFICATION OF REPORT Unclassified 18. SECURITY
... EDUCATION, HOSPITALS, AND OTHER NON-PROFIT ORGANIZATIONS Post-Award Requirements Property Standards § 3019... following information. (i) A description of the equipment. (ii) Manufacturer's serial number, model number... to the General Services Administration by the Federal awarding agency to determine whether a...
Sakai, Takao; Yamakawa, Masanori; Otsuka, Masaya; Sekine, Katsuhisa
Purpose: To reduce equipment thermal stress and deformation by eliminating uneven temperature distribution caused at the equipment through section of the roof slab for the tank FBR, and at the same time, simplify the structure installation. Method: Multiple number of vertical fin projects are fit on the equipment through-section inside wall for the roof slab and the cylindrical equipment peripheral wall, and with these projected fins, the ring space of the through section is vertically divided into multiple sections in the circumferential direction. The vertical fins on the through-section inside wall and the fins on the equipment peripheral wall are contacted with each other by revolving them in the lateral direction. As a result, the natural convection caused by the difference of temperatures in the vertical direction of the ring space becomes a convection within each sector divided, and never generates circumferential circulation, which reduce uneven temperature distribution caused at the equipment through section. (Kawakami, Y.)
Reactor vessel stud bolt handling equipment includes means for transferring a stud bolt to a carrier from a parking station, or vice versa. Preferably a number of stud bolts are handled simultaneously. The transfer means may include cross arms rotatable about extendable columns, and the equipment is mounted on a mobile base for movement into and out of position. Each carrier comprises a tubular socket and an expandable sleeve to grip a stud bolt. (author)
Do international organisations generate benchmarks as tools for policy enforcement or policy learning? This article suggests that the latter is possible even in unlikely scenarios. It does this through a case study on the ‘power of numbers’ in the International Monetary Fund's (IMF) Financial...... Sector Assessment Programme (FSAP). While the IMF is typically viewed as an institution that enforces global standards for economic governance through the imposition of quantitative targets (‘numbers’ for this special issue), I suggest that its use of benchmarking in the generation of financial data can...... is that it seeks to generate a policy dialogue for learning with member states. But this aim also has to operate within broader international political and economic constraints. As such this process must yield to broader principal-agent dynamics in the IMF's governance structure, as well as tip its cap to private...
Tsuru, Shigeto; Weidner, H. (eds.)
This book deals in English with the most important features of Japanese environmental policy in a number of individual articles by different authors. The various sections report on: 1. History and organization of environmental policy; 2. The role of non-governmental actors in environmental policy (large industries); 3. Special features of environmental policies and problems; 4. Classical pollution control areas: Regulations and effects; 5. Environmental problems in a broader perspective (nature conservation); 6. Policy areas with influence on environmental quality; 7. Environmental monitoring and reporting; 8. Japanese environmental policy in an international perspective (preventive policies, developing countries). (HSCH).
On 26 May, CERN once again had the honour of donating computing equipment to a foreign institute. This time, around 100 servers and five network hubs were sent to Senegal, making it the seventh country, after Morocco, Ghana, Bulgaria, Serbia, Egypt and the Philippines, to receive a donation of computing equipment from the Organization. The official ceremony was held at CERN on 26 May in the presence of the Director-General, Rolf Heuer, and Senegal's ambassador to Geneva, Fodé Seck, who both expressed their enthusiasm for the project. The equipment is intended for Cheikh Anta Diop University (UCAD) in Dakar and will be of particular use to students attending the African School of Fundamental Physics and its Applications (ASP 2014) taking place from 3 to 23 August, for which CERN is a partner. The ASP allows a large number of African students to hone their skills in high-energy physics and to forge professional links with fellow physicists in Africa and Europe. ...
It is suggested that clinical engineers take the lead in formulating evaluation processes to recommend equipment replacement. Their skill, knowledge, and experience, combined with access to equipment databases, make them a logical choice. Based on ideas from Fennigkoh's scheme, elements such as age, vendor support, accumulated maintenance cost, and function/risk were used.6 Other more subjective criteria such as cost benefits and efficacy of newer technology were not used. The element of downtime was also omitted due to the data element not being available. The resulting Periop Master Equipment List and its rationale was presented to the Perioperative Services Program Council. They deemed the criteria to be robust and provided overwhelming acceptance of the list. It was quickly put to use to estimate required capital funding, justify items already thought to need replacement, and identify high-priority ranked items for replacement. Incorporating prioritization criteria into an existing equipment database would be ideal. Some commercially available systems do have the basic elements of this. Maintaining replacement data can be labor-intensive regardless of the method used. There is usually little time to perform the tasks necessary for prioritizing equipment. However, where appropriate, a clinical engineering department might be able to conduct such an exercise as shown in the following case study.
INHERENT VICE & INSUFFICIENT PACKING CLAUSES FOR ALL RISKS INSURANCE POLICIES UNDER BRITISH INSTITUTE CARGO CLAUSES : legal issues arising from claims of loss during sea transportation of large technical equipments
Analysis and presentation of this thesis is supported by studies of many relevant cases where the major arguments are set around the exclusion clauses concerning the ‘all risks cover’ policy as found in Institute Cargo Clauses. Two cases are especially emphasized, namely Mayban General Assurance BHD v. Alstom Power Plants Ltd. and Global Process Systems Inc v. Syarikat Takaful Malaysia Berhad , mainly because of the special nature of the subject matter insured in these cases. The legal i...
Nisbet, A; Ward, A
Against a background of increasing demand for radiotherapy equipment, this study was undertaken to investigate options for equipment procurement, in particular to compare purchase with lease. The perceived advantages of lease are that equipment can be acquired within budget and cashflow constraints, with relatively low amounts of cash leaving the NHS in the first year, avoiding the necessity of capitalizing the equipment and providing protection against the risk of obsolescence associated with high technology equipment. The perceived disadvantages of leasing are that the Trust does not own the equipment, leasing can be more expensive in revenue terms, the tender process is extended and there may be lease conditions to be met, which may be costly and/or restrictive. There are also a number of technical considerations involved in the leasing of radiotherapy equipment that influence the financial analysis and practical operation of the radiotherapy service. The technical considerations include servicing and planned preventative maintenance, upgrades, spare parts, subsequent purchase of "add ons", modification of equipment, research and development work, commencement of the lease period, return of equipment at the end of the lease period and negotiations at the end of the lease period. A study from Raigmore Hospital, Inverness is described, which involves the procurement of new, state-of-the-art radiotherapy equipment. This provides an overview of the procurement process, including a summary of the advantages and disadvantages of leasing, with the figures from the financial analysis presented and explained. In addition, a detailed description is given of the technical considerations to be taken into account in the financial analysis and negotiation of any lease contract.
After a recall of some definitions relating to decontamination techniques and of the regulation into effect, the principles to be respected to arrange rationally work zones are quoted while insisting more particularly on the types of coatings which facilitate maintenance operations and the dismantling of these installations. Then, the processes and equipments to use in decontamination units for routine or particular operations are described; the list of recommended chemical products to decontaminate the equipment is given. The influence of these treatments on the state and the duration of life of equipments is studied, and some perfectible methods are quoted. In the appendix, are given: the limits of surface contamination accepted in the centers; a standard project which defines the criteria of admissible residual contamination in wastes considered as cold wastes; some remarks on the interest that certain special ventilation and air curtain devices for the protection of operators working on apparatus generating contaminated dusts [fr
The opinion of a ten of about authors about the consequences of the Chernobylsk accident on the 26. april 1986 and on the future of populations. This study tackles the technical and scientific risk from a socio-anthropological point of view and asks for the possible development after a such disaster. (N.C.)
Greenwalt, B; Henderer, B; Hibbard, W; Mercer, M
The Iraq Department of Border Enforcement is rich in personnel, but poor in equipment. An effective border control system must include detection, discrimination, decision, tracking and interdiction, capture, identification, and disposition. An equipment solution that addresses only a part of this will not succeed, likewise equipment by itself is not the answer without considering the personnel and how they would employ the equipment. The solution should take advantage of the existing in-place system and address all of the critical functions. The solutions are envisioned as being implemented in a phased manner, where Solution 1 is followed by Solution 2 and eventually by Solution 3. This allows adequate time for training and gaining operational experience for successively more complex equipment. Detailed descriptions of the components follow the solution descriptions. Solution 1 - This solution is based on changes to CONOPs, and does not have a technology component. It consists of observers at the forts and annexes, forward patrols along the swamp edge, in depth patrols approximately 10 kilometers inland from the swamp, and checkpoints on major roads. Solution 2 - This solution adds a ground sensor array to the Solution 1 system. Solution 3 - This solution is based around installing a radar/video camera system on each fort. It employs the CONOPS from Solution 1, but uses minimal ground sensors deployed only in areas with poor radar/video camera coverage (such as canals and streams shielded by vegetation), or by roads covered by radar but outside the range of the radar associated cameras. This document provides broad operational requirements for major equipment components along with sufficient operational details to allow the technical community to identify potential hardware candidates. Continuing analysis will develop quantities required and more detailed tactics, techniques, and procedures.
Mendonça, J. Ricardo G.
We define a new class of numbers based on the first occurrence of certain patterns of zeros and ones in the expansion of irracional numbers in a given basis and call them Sagan numbers, since they were first mentioned, in a special case, by the North-american astronomer Carl E. Sagan in his science-fiction novel "Contact." Sagan numbers hold connections with a wealth of mathematical ideas. We describe some properties of the newly defined numbers and indicate directions for further amusement.
Vorob'ev, Nikolai Nikolaevich
Fibonacci numbers date back to an 800-year-old problem concerning the number of offspring born in a single year to a pair of rabbits. This book offers the solution and explores the occurrence of Fibonacci numbers in number theory, continued fractions, and geometry. A discussion of the ""golden section"" rectangle, in which the lengths of the sides can be expressed as a ration of two successive Fibonacci numbers, draws upon attempts by ancient and medieval thinkers to base aesthetic and philosophical principles on the beauty of these figures. Recreational readers as well as students and teacher
Ejersbo, Lisser Rye; Misfeldt, Morten
through using mathematical names for the numbers such as one-ten-one for 11 and five-ten-six for 56. The project combines the renaming of numbers with supporting the teaching with the new number names. Our hypothesis is that Danish children have more difficulties learning and working with numbers, because...... the Danish number names are more complicated than in other languages. Keywords: A research project in grade 0 and 1th in a Danish school, Base-10 system, two-digit number names, semiotic, cognitive perspectives....
Duah, Nancy O; Matrevi, Sena A; de Souza, Dziedzom K; Binnah, Daniel D; Tamakloe, Mary M; Opoku, Vera S; Onwona, Christiana O; Narh, Charles A; Quashie, Neils B; Abuaku, Benjamin; Duplessis, Christopher; Kronmann, Karl C; Koram, Kwadwo A
With the introduction of artemisinin-based combination therapy (ACT) in 2005, monitoring of anti-malarial drug efficacy, which includes the use of molecular tools to detect known genetic markers of parasite resistance, is important for first-hand information on the changes in parasite susceptibility to drugs in Ghana. This study investigated the Plasmodium falciparum multidrug resistance gene (pfmdr1) copy number, mutations and the chloroquine resistance transporter gene (pfcrt) mutations in Ghanaian isolates collected in seven years to detect the trends in prevalence of mutations. Archived filter paper blood blots collected from children aged below five years with uncomplicated malaria in 2003-2010 at sentinel sites were used. Using quantitative real-time polymerase chain reaction (qRT-PCR), 756 samples were assessed for pfmdr1 gene copy number. PCR and restriction fragment length polymorphism (RFLP) were used to detect alleles of pfmdr1 86 in 1,102 samples, pfmdr1 184, 1034, 1042 and 1246 in 832 samples and pfcrt 76 in 1,063 samples. Merozoite surface protein 2 (msp2) genotyping was done to select monoclonal infections for copy number analysis. The percentage of isolates with increased pfmdr1 copy number were 4, 27, 9, and 18% for 2003-04, 2005-06, 2007-08 and 2010, respectively. Significant increasing trends for prevalence of pfmdr1 N86 (×(2) = 96.31, p resistance has been reported. The decreasing trend in the prevalence of chloroquine resistance markers after change of treatment policy presents the possibility for future introduction of chloroquine as prophylaxis for malaria risk groups such as children and pregnant women in Ghana.
Florida Power ampersand Lights's (FP ampersand L's) Turkey Point units were built prior to the establishment of American Society of Mechanical Engineers' Sec. III requirements. Since that time, FP ampersand L has voluntarily committed to procuring some spare and replacement parts in compliance with the ordering requirements of ASME Sec. III. New subsystems were designed according to ASME Sec. III requirements. In 1978, 10CFR21 of the Code of Federal Regulations was federally mandated. Environmental qualification concerns and the Three Mile Island incident further complicated the stocking and ordering of spare and replacement parts. Turkey Point assembled a team of quality assurance, quality control, and engineering people and obtained permission to directly access the store department computer so that catalog descriptions could be quickly made available for use by the plant. The total equipment parts configuration (TEPC) system was designed and developed under the direction of the procurement document review team at the Turkey Point nuclear plant. The system is a network of related computer data bases that identifies the equipment at the plant. The equipment (or components that make up a piece of equipment) is identified by a tag/component code system. Each component is further broken down by the manufacturer's parts list or bill of material. A description of the data available to the user, the ways these data can be accessed and displayed, and a description of the data bases and their relation to each other are summarized in this paper
The current booklet is intended to give a full and balanced description of the techniques and equipment used for both nuclear material accountancy and containment and surveillance measures, and for the new safeguards measure of environmental sampling. As new verification measures continue to be developed, the material in the booklet will be periodically reviewed and updated versions issued. (author)
Shyamprasad, M.; Ramaswamy, V.
bed, and a digital clock and a transponder helped to locate the camera. Equipment for the analysis of the nodules such as x-ray fluorescence and atomic absorption spectrophotometers were installed aboard MV Skandi Surveyor and MV Fernella and MV G A...
Experimental equipment around the ORPHEE reactor is presented. The neutron source; and the spectrometers and sample environment (inelastic and quasi-elastic scattering, elastic scattering, spread scattering, small angle scattering) are described. An experiment proposal and reports guide is supplied [fr
Petersen, T Kyle
This text presents the Eulerian numbers in the context of modern enumerative, algebraic, and geometric combinatorics. The book first studies Eulerian numbers from a purely combinatorial point of view, then embarks on a tour of how these numbers arise in the study of hyperplane arrangements, polytopes, and simplicial complexes. Some topics include a thorough discussion of gamma-nonnegativity and real-rootedness for Eulerian polynomials, as well as the weak order and the shard intersection order of the symmetric group. The book also includes a parallel story of Catalan combinatorics, wherein the Eulerian numbers are replaced with Narayana numbers. Again there is a progression from combinatorics to geometry, including discussion of the associahedron and the lattice of noncrossing partitions. The final chapters discuss how both the Eulerian and Narayana numbers have analogues in any finite Coxeter group, with many of the same enumerative and geometric properties. There are four supplemental chapters throughout, ...
Practical possibilities are discussed of seismic modifications of power plant structures and systems with a view to ancillary equipment providing such modifications. Briefly outlined are the possibilities of reinforcing technological equipment and systems operating at normal temperatures, where the basic precondition of seismic resistance is strong and reliable anchorage. Attention is paid to equipment handling high temperature media. In these cases, in selecting seismic protection thermal expansion should be considered as an accompanying effect. Different types are described in detail of hydraulic and mechanical limiters of foreign makes. It is stated on the basis of practical experience that hydraulic limiters involve a number of problems. Mechanical limiters seem to be more appropriate in spite of the complexity of their operation. Viscous dampers are another suitable element for the seismic protection of power plant technological equipment. (Z.M.). 22 figs., 3 tabs., 19 refs
Transfinite Numbers. What is Infinity? S M Srivastava. In a series of revolutionary articles written during the last quarter of the nineteenth century, the great Ger- man mathematician Georg Cantor removed the age-old mistrust of infinity and created an exceptionally beau- tiful and useful theory of transfinite numbers. This is.
Bonzon, L.L.; Craft, C.M.; McCulloch, W.H.; Sebrell, W.A.
The USNRC sponsors a number of programs at Sandia National Laboratories (SNL) specifically addressing safety-related equipment survivability. The major thrust of these programs has been the physical testing of equipment. Test results illustrate the importance of a dedicated equipment design effort giving particular attention to the safety implications of the equipment operation. Several equipment survivability tests here have revealed equipment design and test-related deficiencies
Bonzon, L.L.; Craft, Ch.M.; McCulloch, W.H.; Sebrell, W.A.
The USNRC sponsors a number of programs at Sandia National Laboratories (SNL) specifically addressing safety-related equipment survivability. The major thrust of these programs has been the physical testing of equipment. Test results illustrate the importance of a dedicated equipment design effort giving particular attention to the safety implications of the equipment operation. Several equipment survivability tests here have revealed equipment design and test-related deficiencies
Kang, Cheol Hui
This book is divided two parts about visual communication and terminal equipment. The first part introduces visual communication, which deals with foundation of visual communication, technique of visual communication, equipment of visual communication, a facsimile and pictorial image system. The second part contains terminal equipment such as telephone, terminal equipment for data transmission on constitution and constituent of terminal equipment for data transmission, input device and output device, terminal device and up-to-date terminal device.
... Conservation Program for Consumer Products: Test Procedures for Direct Heating Equipment and Pool Heaters... test procedures for direct heating equipment and pool heaters established under the Energy Policy and... covered products at least once every seven years. For direct heating equipment, the proposed amendments...
Andrews, George E
Although mathematics majors are usually conversant with number theory by the time they have completed a course in abstract algebra, other undergraduates, especially those in education and the liberal arts, often need a more basic introduction to the topic.In this book the author solves the problem of maintaining the interest of students at both levels by offering a combinatorial approach to elementary number theory. In studying number theory from such a perspective, mathematics majors are spared repetition and provided with new insights, while other students benefit from the consequent simpl
The patent concerns a warning and protection system for mobile x-ray equipment used for 'on site' radiography, so that workers in the vicinity of such a working unit can be alerted to its presence. The invention is a local repeater warning system which gives a preliminary warning that energisation of the tubehead is imminent, as well as a switch near the tubehead to abort or inhibit energisation. The latter switch allows personnel caught in the vicinity of the tubehead to prevent energisation. The preliminary warning may be flashing lamps or by a klaxon. The control unit for the equipment may include a monitoring circuit to detect failure of the warning light or klaxon. (U.K.)
The patent concerns a warning and protection system for mobile x-ray equipment used for 'on site' radiography, so that workers in the vicinity of such a working unit can be alerted to its presence. The invention is a local repeater warning system which gives a preliminary warning that energisation of the tubehead is imminent, as well as a switch near the tubehead to abort or inhibit energisation. The latter switch allows personnel caught in the vicinity of the tubehead to prevent energisation. The preliminary warning may be flashing lamps or by a klaxon. The control unit for the equipment may include a monitoring circuit to detect failure of the warning light or klaxon. (U.K.).
S. L. Rovin
Full Text Available This article presents an automated cupola complex, developed by scientific-production enterprise «Technolit» together with GSTU named after P. O. Sukhoi, launched in the spring of 2015 at the plant «Stroiex» in the city of Chelyabinsk (the Russian Federation. The old cupolas (open type have been replaced by the new cupolas of the closed type, equipped with automatic control and management system and multistage wet gas treatment system. Cupolas are equipped with systems of post-combustion gases and the batch charging, the separate systems of air blast, systems of sludge removal and recirculation of water, the slag granulation installations, mechanized cleaning of cupola furnace and automatic safety system. These activities allowed the company to increase production and improve the quality of cast iron, reduce the coke consumption by 20% and reducing emissions of pollutants into the atmosphere almost 30 times.
End of February 1977 a Soviet Ilyushin-76 heavy freight aircraft landed at Cointrin airport having on board fifty large wire proprtional chambers and associated apparatus, together weighing 10 tons, supplied by the Joint Institute for Nuclear Research, Dubna, USSR. The equipment was for the CERN- Dubna-Munich-Saclay experiment NA4 on deep inelastic muon scattering being set up in the North Area of SPS. See Weekly Bulletin 11/78.
Equipment is described featuring a means for the mechanical connection of a transmitting probe to the electronic supply unit which consists of a flexible rod which may only be bent in a single plane. The transmitting probe is pressed against the borehole wall by a spring attached to the probe whose longitudinal axis is in the same plane in which the rod may be bent. (B.S.)
This Practical Radiation Technical Manual is one of a series that has been designed to provide guidance on radiological protection for employers, radiation protection officers, managers and other technically competent persons who have responsibility for ensuring the safety of employees working with ionizing radiation. The Manual may be used with the appropriate IAEA Practical Radiation Safety Manuals to provide training, instruction and information for all employees engaged in work with ionizing radiation. Personal protective equipment (PPE) includes clothing or other special equipment that is issued to individual workers to provide protection against actual or potential exposure to ionizing radiations. It is used to protect each worker against the prevailing risk of external or internal exposure in circumstances in which it is not reasonably practicable to provide complete protection by means of engineering controls or administrative methods. Adequate personal protection depends on PPE being correctly selected, fitted and maintained. Appropriate training for the users and arrangements to monitor usage are also necessary to ensure that PPE provides the intended degree of protection effectively. This Manual explains the principal types of PPE, including protective clothing and respiratory protective equipment (RPE). Examples of working procedures are also described to indicate how PPE should be used within a safe system of work. The Manual will be of most benefit if it forms part of a more comprehensive training programme or is supplemented by the advice of a qualified expert in radiation protection. Some of the RPE described in this Manual should be used under the guidance of a qualified expert
In this intriguing book, John Barnes takes us on a journey through aspects of numbers much as he took us on a geometrical journey in Gems of Geometry. Similarly originating from a series of lectures for adult students at Reading and Oxford University, this book touches a variety of amusing and fascinating topics regarding numbers and their uses both ancient and modern. The author intrigues and challenges his audience with both fundamental number topics such as prime numbers and cryptography, and themes of daily needs and pleasures such as counting one's assets, keeping track of time, and enjoying music. Puzzles and exercises at the end of each lecture offer additional inspiration, and numerous illustrations accompany the reader. Furthermore, a number of appendices provides in-depth insights into diverse topics such as Pascal’s triangle, the Rubik cube, Mersenne’s curious keyboards, and many others. A theme running through is the thought of what is our favourite number. Written in an engaging and witty sty...
MARIA LOREDANA NICOLESCU
Full Text Available This paper presents an analysis of household behaviour to the collection of waste electrical and electronic equipment in Romania based on an econometric multifactorial linear regression model. In the model, the amount of WEEE* collected in the counties rep resents the endogenous variable, and factors such as regional gross domestic product, the number of employees, monthly average net nominal earnings, unemployed persons, retirees, existing housing, education and other non - quantifiable factors with regional influence are influence factors or explanatory (exogenous variables. The period considered for the study is 2010 - 2012, and statistics are taken and processed at county level. The study is necessary to identify the extent to which those factors influence t he collection of WEEE from private households. The results of this study may lead to an improvement of the management of waste electrical and electronic equipment in Romania, being useful for policy makers and stakeholders involved in the system.
Ejersbo, Lisser Rye; Misfeldt, Morten
This paper concerns the results from the first year of a three-year research project involving the relationship between Danish number names and their corresponding digits in the canonical base 10 system. The project aims to develop a system to help the students’ understanding of the base 10 system...... the Danish number names are more complicated than in other languages. Keywords: A research project in grade 0 and 1th in a Danish school, Base-10 system, two-digit number names, semiotic, cognitive perspectives....
The purpose of this document is to define the system requirements for the Master Equipment List (MEL) Phase 1 project. The intended audience for this document includes Data Automation Engineering (DAE), Configuration Management Improvement and Control Engineering (CMI and CE), Data Administration Council (DAC), and Tank Waste Remedial System (TWRS) personnel. The intent of Phase 1 is to develop a user-friendly system to support the immediate needs of the TWRS labeling program. Phase 1 will provide CMI and CE the ability to administrate, distribute, and maintain key information generated by the labeling program. CMI and CE is assigning new Equipment Identification Numbers (EINs) to selected equipment in Tank Farms per the TWRS Data Standard ``Tank Farm Equipment Identification Number``. The MEL Phase 1 system will be a multi-user system available through the HLAN network. It will provide basic functions such as view, query, and report, edit, data entry, password access control, administration and change control. The scope of Phase 1 data will encompass all Tank Farm Equipment identified by the labeling program. The data will consist of fields from the labeling program`s working database, relational key references and pointers, safety class information, and field verification data.
Theodore M. Porter
Full Text Available The struggle over cure rate measures in nineteenth-century asylums provides an exemplary instance of how, when used for official assessments of institutions, these numbers become sites of contestation. The evasion of goals and corruption of measures tends to make these numbers “funny” in the sense of becoming dis-honest, while the mismatch between boring, technical appearances and cunning backstage manipulations supplies dark humor. The dangers are evident in recent efforts to decentralize the functions of governments and corporations using incen-tives based on quantified targets.
Winckworth, Lucinda C; McLaren, Emma; Lingeswaran, Arvin; Kelsey, Michael
Neonatal infections carry a heavy burden of morbidity and mortality. Poor practice can result in unintentional colonisation of medical equipment with potentially pathogenic organisms. This study will determine the prevalence and type of bacterial contamination on exposed neonatal resuscitation equipment in different clinical settings and explore simple measures to reduce contamination risk. A survey determined the rates of resuscitation equipment usage. All environmentally exposed items were identified on resuscitaires hospital-wide and swabbed for bacterial contamination. A new cleaning and storage policy was implemented and the prevalence of environmentally exposed equipment re-measured post-intervention. Resuscitation equipment was used in 28% of neonatal deliveries. Bacterial colony forming units were present on 44% of the 236 exposed equipment pieces swabbed. There was no significant difference in contamination rates between equipment types. Coagulase negative staphylococcus was the most prevalent species (59 pieces, 25%) followed by Escherichia coli and Enterobacter cloacae (20 pieces, 9% each). Opened items stored inside plastic remained sterile, whilst those in low-use areas had significantly less contamination than those in high-use areas (22% vs. 51%, P reduction in environmentally exposed equipment (79% reduction, P < 0.01). Pathogenic bacteria can colonise commonly used pieces of neonatal resuscitation equipment. Whilst the clinical significance remains uncertain, equipment should be kept packaged until required and discarded once open, even if unused. Standardising cleaning policies results in rapid and significant improvements in equipment storage conditions, reducing microbial colonisation opportunities. © 2016 Paediatrics and Child Health Division (The Royal Australasian College of Physicians).
Reshaping skills policy in South Africa: structures, policies and processes. ... New Agenda: South African Journal of Social and Economic Policy ... South African skills development policy since the promulgation of the Skills Development Act of 1998 has undergone a number of different iterations or attempts at accelerating ...
Lange, Bettina; Alexiadou, Nafsika
Open methods for coordinating (OMC) education policies in the EU rely on a number of techniques, one of which is policy learning. This article examines how policy learning and governance transform each other. More specifically, policy-learning in the education OMC becomes differentiated into four distinct learning styles: mutual, competitive,…
It is instructive and interesting to find hidden numbers by using different positional numeration systems. Most of the present guessing techniques use the binary system expressed as less-than, greater-than or present-absent type information. This article describes how, by employing four cards having integers 1-64 written in different colours, one…
this is a characteristic difference between finite and infinite sets and created an immensely useful branch of mathematics based on this idea which had a great impact on the whole of mathe- matics. For example, the question of what is a number (finite or infinite) is almost a philosophical one. However Cantor's work turned it ...
Home; Journals; Resonance – Journal of Science Education; Volume 2; Issue 3. Transfinite Numbers - What is Infinity? S M Srivastava. General Article Volume 2 Issue 3 March 1997 pp 58-68. Fulltext. Click here to view fulltext PDF. Permanent link: https://www.ias.ac.in/article/fulltext/reso/002/03/0058-0068 ...
Part of the effort of the Seismic Safety Margins Research Program (SSMRP) has been directed at generating a fragility data base for equipment used in control and safety systems in commercial nuclear power plants. Component fragility data exist in various forms, depending on their content, intended use, and level of reduction. Th data are stored in a relational data base on the LLNL CDC 7600 computers; this provides easy accessibility for LLNL computer users. This report describes the present structure of the data base and presents its contents through the use of tables
The study looks at the mining equipment industry as coal mining equipment is a subsector within this industry. This study seeks to create an understanding of how the coal mining equipment industry in South Africa is affected by the emergence of China as a mining equipment supplier. China's globalisation is set to continue and will impact all industries. China's African Policy will also impact the African continent, as China will continue to invest and use Africa's mineral resources. Sourcing ...
Chattin, Fred Rhea [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Wilson, Kenton [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Ezold, Julie G. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)
To successfully continue the 252Cf production and meet the needs of the customers, a comprehensive evaluation of the Building 7920 processing equipment was requested to identify equipment critical to the operational continuity of the program.
Full Text Available A number of potentially harmful pollutants are emitted from office equipment. Printers and copiers are sources of volatile organic compounds (VOC, which at least partly, are generated from the heated toner and paper dust during printing process. Benzene, toluene, ethylbenzene, xylenes, styrene, and formaldehyde were detected in the blended emissions emitted from printing devices. Office printing devices are recognized to be the major sources of indoor fine and ultrafine aerosol particles. The emissions of certain pollutants from office equipment may be at relatively low level compared to other known sources (e.g. building materials. However, office equipment is potentially the important source of human exposure due to the short distance for the people operating them both at home and in the office.
The purpose of this document is to list the Characterization equipment drawings that are classified as Essential Drawings. Essential Drawings: Are those drawings identified by the facility staff as necessary to directly support the safe operation of the facility or equipment (HNF 1997a). The Characterization equipment drawings identified in this report are deemed essential drawings as defined in HNF-PRO-242, Engineering Drawing Requirements (HNF 1997a). These drawings will be prepared, revised, and maintained per HNF-PRO-440, Engineering Document Change Control (HNF 1997b). All other Characterization equipment drawings not identified in this document will be considered Support drawings until the Characterization Equipment Drawing Evaluation Report is completed
Lestari, C.; Kurniati, N.
The cost structure for equipment investment including purchase cost and maintenance cost is getting more expensive. The company considers to lease the equipment instead of purchase it under a contractual agreement. Offering to extend the lease period, following to the base lease period, will provide more benefits for both the lessor (owner) and the lessee (user). Whenever the lease period extension offered at the beginning of the contract, there are some risks in finance e.g. uncertainty of the equipment performance and lessor responsibility. Therefore, this research attempts to model the optimal maintenance policy for lease period extension offered at the end of the contract. Minimal repair is performed to rectify a failed equipment, while imperfect preventive maintenance is conducted to improve the operational state of the equipment when reaches a certain control limit to avoid failures. The mathematical model is constructed to determine the optimal control limit, the number and degree of preventive maintenance, and the multiplication number of the lease period extension. Finally, numerical examples are given to illustrate the influences of the optimal length of the extended lease and the maintenance policy to minimize the maintenance cost.
Abramova, I. G.; Abramov, D. A.
This article documents the methods applied in production control technics specifically focused on commonly used parameter OEE (Overall Equipment Effectiveness). The indicators of extensive and intensive use of equipment are considered. Their appointment this is comparison in the same type of production within the industry and comparison of single-type and / or different types of equipment in terms of capacity. However, it is shown that there is no possibility of revealing the reasons for the machine’s operation: productive / unproductive, with disturbances. Therefore, in the article reveals the approaches to calculating the indicator characterizing the direct operation of the equipment. The Machine Load coefficient is approaching closely to the indicator of the efficiency of the use of equipment. Methods analysis is proceeded through the historically applied techniques such as “Stopwatch” and “Motion” studies. Was performed the analysis of the efficiency index of OEE equipment using the comparable indexes performance of equipment in the Russian practice. An important indicator of OEE contains three components. The meaning of each of them reflects historically applicable indicators. The value of the availability of equipment indicator is close to the value of the equipment extensibility index. The value of the indicator of the efficiency of work can be compared with the characteristic of the capacity of the equipment and the indicator of the quality level can meet the requirements for compliance with the manufacturing technology. Shown that the sum of the values of the coefficient of “Availability” of the equipment and the value of the “Factor of compaction of working hours” are one. As well as the total value of the indicator “level of quality” and the coefficient of marriage given in the result unit. The measurability of the indicators makes it possible to make a prediction about efficiency of the equipment.
Schultz, Mark D.
According to one embodiment, a system for removing heat from a rack of information technology equipment may include a sidecar indoor air to liquid heat exchanger that cools warm air generated by the rack of information technology equipment. The system may also include a liquid to liquid heat exchanger and an outdoor heat exchanger. The system may further include configurable pathways to connect and control fluid flow through the sidecar heat exchanger, the liquid to liquid heat exchanger, the rack of information technology equipment, and the outdoor heat exchanger based upon ambient temperature and/or ambient humidity to remove heat from the rack of information technology equipment.
Arifin, Muhammad Faizal Ardhiansyah
Earth fill work with large volumes of soil deposits will involve a lot of heavy equipment with a variety of functions and with different objectives. Where each machine will have different productivity anyway. So that in this paper discusses the calculation of the cost required to do the compacted earthfill work for embankment in accordance with the volume of work, the target date for implementation, and the number of heavy equipment needs. As the cost calculations used heavy equipment rental price per hour. In the cost analysis calculations use heavy equipment here there are several factors that we included in the calculation, are: 1.)Hauling distance; 2.)Effective hour a day; 3.)Change factor of Soil Volume; 4.)Effective Speed; 5.)Equipment efficiency factor; 6.)Equipment coefficient; 7.)Cycle Time.
A number of memoranda and reports are collected which deal with evaluations of solar energy policy options, including direct and indirect labor impacts and costs of different options and consumer protection. (LEW)
Medical devices and equipment have become an indispensable part of modern medical practice. Yet these medical technologies receive scant attention in the Indian context, both at the health policy level and as an area of study. There has been little attempt to systematically address the issue of equipment based medical technologies and how to regulate their use. There is paucity of primary data on the kind of medical equipment and techniques being introduced, on their need and relative usefulness, reliability, patterns of utilization, on their production, procurement, distribution, costs, and accessibility. This article reviews some of the policy issues relating to equipment based medical technology in India, in light of the specific choices and policies made during and after the colonial period in favour of modern medicine and a technology-based public health system, attempts at self-sufficiency and the current international environment with respect to the medical equipment and health-care industry.
... specifically permitted or contemplated by Federal statute. (4) When acquiring replacement equipment, the...) Management requirements. Procedures for managing equipment (including replacement equipment), whether... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no...
... specifically permitted or contemplated by Federal statute. (4) When acquiring replacement equipment, the...) Management requirements. Procedures for managing equipment (including replacement equipment), whether... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no...
... specifically permitted or contemplated by Federal statute. (4) When acquiring replacement equipment, the...) Management requirements. Procedures for managing equipment (including replacement equipment), whether... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no...
Pepper, Susan; Farnitano, Michael; Carelli, Joseph
Full text: During the 1990s, the IAEA Department of Safeguards began a transition from analog to digital equipment. This included surveillance equipment, seals, NDA measurement systems, and other instruments. The transition to digital equipment was intended to facilitate compatibility between and integration of instruments, remote communication of data, improved data storage, and modernization. Many of the instruments are designed to operate on battery power during loss of facility power, and therefore, are designed to consume minimal power. In 2000, the IAEA experienced a number of failures in digital image surveillance (DIS) equipment. A study of the performance data revealed that the failures occurred in 'high risk' environments where the systems were exposed to neutrons. As a supporter of IAEA equipment development and implementation, the U.S. Support Program worked with the IAEA, the equipment designer, and the equipment manufacturer in special meetings on DIS to determine the cause of the failures. It was as a result of these meetings that single event upset (SEU) was determined to be the root cause of the failures. The meeting participants also identified a list of actions to improve the reliability of DIS systems. As a result of the DIS meetings and the identified actions, the U.S. Support Program approved a request from the IAEA and established Task E.125, 'Remote Monitoring and Unattended Digital Surveillance Systems.' This task is an umbrella task intended to provide a mechanism for response to IAEA needs related to improving the reliability of unattended, remote monitoring and DIS equipment. Subtasks approved under this task include: E.125.1, 'SDIS Software Consolidation and DCM-14 Audit' - This subtask involves the consolidation of a number of individual upgrades to the SDIS and review of the DCM-14 software. As the sponsor of the design of the DCM-14 by Dr. Neumann, the German Support Program is also a participant in this subtask; E.125.2, 'DIS
The demands of the electricity market have led the French nuclear industry to seek ways of reducing the purchasing costs nuclear power plant components while maintaining an equivalent level of quality and safety. A project (ECOREP) was undertaken on this subject from 1997 to 2000 by EDF and FRAMATOME. Based on in-depth exchanges with suppliers and major companies in non-nuclear sectors, it highlighted the over-specific and sometimes unjustified nature of many of the existing requirements existing. Covering the areas of both general instructions (quality assurance, supplier surveillance, documentation) and technical requirements, the project recognised that there was some good practice in non-nuclear industries which could be adopted without any adverse effects, particularly by ensuring that the requirements are defined in terms of ends rather than means. The simulation analyses carried out led to an estimate that a saving of at least 10% is feasible by attempting to emulate this good non-nuclear industrial practice wherever possible. In particular, reference to more widely-used conventional manufacturing codes is recommended. (author)
Noland, Lynn [Director, Sponsored Programs
Whitworth University constructed a 63,00 sq. ft. biology and chemistry building which opened in the Fall of 2011. This project provided for new state-of-the-art science instrumentation enabling Whitworth students to develop skills and knowledge that are directly transferable to practical applications thus enhancing Whitworth student's ability to compete and perform in the scientific workforce. Additionally, STEM faculty undertake outreach programs in the area schools, bringing students to our campus to engage in activities with our science students. The ability to work with insturmentation that is current helps to make science exciting for middle school and high school students and gets them thinking about careers in science. 14 items were purchased following the university's purchasing policy, that benefit instruction and research in the departments of biology, chemistry, and health sciences. They are: Cadaver Dissection Tables with Exhaust Chamber and accessories, Research Microscope with DF DIC, Phase and Fluorescence illumination with DP72 Camera, Microscope with Fluorescence, Microcomputer controlled ultracentrifuge, Ultracentrifuge rotor, Variable Temperature steam pressure sterilizer, Alliance APLC System, DNA Speedvac, Gel Cocumentation System, BioPac MP150, Glovebox personal workstation,Lyophilizer, Nano Drop 2000/2000c Spectrophotometer, C02 Incubator.
Vondráčková, Terezie; Kraus, Michal; Šál, Jiří
Intensification of industrial production, increasing citizens’ living standards, expanding the consumer assortment mean in the production - consumption cycle a constantly increasing occurrence of waste material, which by its very nature must be considered as a source of useful raw materials in all branches of human activity. In addition to strict legislative requirements, a number of circumstances characterize waste management. It is mainly extensive transport associated with the handling and storage of large volumes of substances with a large assortment of materials (substances of all possible physical and chemical properties) and high demands on reliability and time coordination of follow-up processes. Considerable differences in transport distances, a large number of sources, processors and customers, and not least seasonal fluctuations in waste and strong price pressures cannot be overlooked. This highlights the importance of logistics in waste management. Soils that are contaminated with oil and petroleum products are hazardous industrial waste. Methods of industrial waste disposal are landfilling, biological processes, thermal processes and physical and chemical methods. The paper focuses on the possibilities of degradation of oil pollution, in particular biodegradation by bacteria, which is relatively low-cost among technologies. It is necessary to win the fight with time so that no ground water is contaminated. We have developed two additional devices to help reduce oil accident of smaller ranges. In the case of such an oil accident, it is necessary to carry out the permeability test of contaminated soil in time and, on this basis, to choose the technology appropriate to the accident - either in-sit biodegradation - at the site of the accident, or on-sit - to remove the soil and biodegrade it on the designated deposits. A special injection drill was developed for in-sit biodegradation, tossing and aeration equipment of the extracted soil was developed for
... 46 Shipping 4 2010-10-01 2010-10-01 false Survival craft number and arrangement. 108.525 Section... UNITS DESIGN AND EQUIPMENT Lifesaving Equipment § 108.525 Survival craft number and arrangement. (a... arrangement of survival craft: (1) Lifeboats with an aggregate capacity to accommodate the total number of...
Menéndez, Cammie K C; Amandus, Harlan E; Damadi, Parisa; Wu, Nan; Konda, Srinivas; Hendricks, Scott A
Taxicab drivers historically have had one of the highest work-related homicide rates of any occupation. In 2010 the taxicab driver homicide rate was 7.4 per 100,000 drivers, compared to the overall rate of 0.37 per 100,000 workers. Evaluate the effectiveness of taxicab security cameras and partitions on citywide taxicab driver homicide rates. Taxicab driver homicide rates were compared in 26 major cities in the U.S. licensing taxicabs with security cameras (n=8); bullet-resistant partitions (n=7); and cities where taxicabs were not equipped with either security cameras or partitions (n=11). News clippings of taxicab driver homicides and the number of licensed taxicabs by city were used to construct taxicab driver homicide rates spanning 15 years (1996-2010). Generalized estimating equations were constructed to model the Poisson-distributed homicide rates on city-specific safety equipment installation status, controlling for city homicide rate and the concurrent decline of homicide rates over time. Data were analyzed in 2012. Cities with cameras experienced a threefold reduction in taxicab driver homicides compared with control cities (RR=0.27; 95% CI=0.12, 0.61; p=0.002). There was no difference in homicide rates for cities with partitions compared with control cities (RR=1.15; 95% CI=0.80, 1.64; p=0.575). Municipal ordinances and company policies mandating security cameras appear to be highly effective in reducing taxicab driver deaths due to workplace violence. Published by Elsevier Inc. on behalf of American Journal of Preventive Medicine
Takase, Kentaro; Kasai, Masao
Rationalization of the plant maintenance is one of the main topics being investigated in Japanese nuclear power industries. Optimization of the inspection and replacement period of equipments is effective for the maintenance cost reduction. The more realistic model of the replacement policy is proposed in this study. It is based on the classical replacement policy model and its cost is estimated. Then, to consider the inspection for the maintenance, the formulation that includes the risk concept is discussed. Based on it, two variations of the combination of the inspection and the replacement are discussed and the costs are estimated. In this study the effect of the degradation of the equipment is important. The optimized maintenance policy depends on the existence of significant degradation. (author)
National Sanitation Foundation, Ann Arbor, MI.
Equipment design specifications are presented relating to tables of all kinds, counters, sinks and drainboards, bins, shelves, drawers, hoods and similar kitchen appurtenances, not including baking, roasting, toasting, broiling or frying equipment, food preparation machinery such as slicers, choppers, and cutters, mixers and grinders, steam…
The equipment in Qinshan CANDU unit is characterized by large number and complex structure. Some equipment failure has no relation with the operation time, it is impossible to avoid the failure of these equipment only by periodical maintenance. To improve the equipment reliability, increase the equipment usability and decrease the maintenance cost, for important equipment related to nuclear safety and generating electricity, it is required to perform condition monitoring and the predictive maintenance (PdM). According to different characteristics of equipment, it is required to use suitable equipment condition monitoring method, content and frequency. In this way, some potential equipment failure can be found, preventive maintenance can be arranged in advance, and equipment maintenance management can be optimized. (author)
Schultz, Mark D.
According to one embodiment, a system for removing heat from a rack of information technology equipment may include a sidecar indoor air to liquid heat exchanger that cools air utilized by the rack of information technology equipment to cool the rack of information technology equipment. The system may also include a liquid to liquid heat exchanger and an outdoor heat exchanger. The system may further include configurable pathways to connect and control fluid flow through the sidecar heat exchanger, the liquid to liquid heat exchanger, the rack of information technology equipment, and the outdoor heat exchanger based upon ambient temperature and/or ambient humidity to remove heat generated by the rack of information technology equipment.
Gabriel Gerber Hornink
Full Text Available Equipe de Trabalho 2014 1. Equipe editorial Editor-Chefe Bayardo Bapstista Torres, Instituto de Química - USP, Brasil Eduardo Galembeck, Departamento de Bioquímica Instituto de Biologia UNICAMP, Brasil Editores Gabriel Gerber Hornink, Depto. Bioquímica, Instituto de Ciências Biomédicas, Universidade - Federal de Alfenas - Unifal-MG, Brasil Vera Maria Treis Trindade, Instituto de Ciências Básicas da Saúde, Departamento de Bioquímica, Universidade Federal do Rio Grande do Sul, Brasil Corpo Editorial Adriana Cassina, Departamento de Bioquímica, Facultad de Medicina, Universidad de la República, Uruguai Angel Herráez, Departamento de Bioquímica y Biología molecular, Universidad de Alcalá de Henares, Madrid, Espanha André Amaral Gonçalves Bianco, Universidade Federal de São Paulo (Unifesp, Brasil Denise Vaz de Macedo, Departamento de Bioquímica, Instituto de Biologia, Universidade Estadual de Campinas - Unicamp, Brasil Eneida de Paula, Departamento de Bioquímica, Instituto de Biologia, Universidade Estadual de Campinas - Unicamp, Brasil Guilherme Andrade Marson, Instituto de Química - USP, Brasil Jose Antonio Martinez Oyanedel, Universidad de Concepción, Chile Josep Maria Fernández Novell, Dept. Bioquímica i Biologia Molecular Universitat de Barcelona, Espanha Leila Maria Beltramini, Instituto de Física de São Carlos, Universidade Estadual de São Paulo - USP, Brasil Manuel João da Costa, Escola de Ciências da Saúde, Universidade do Minho, Portugal Maria Lucia Bianconi, Instituto de Bioquímica Médica Universidade Federal do Rio de Janeiro (UFRJ, Brasil María Noel Alvarez, Departamento de Bioquímica, Facultad de Medicina, Universidad de la República, Uruguai Miguel Ángel Medina Torres, Department of Molecular Biology & Biochemistry Faculty of Sciences University of Málaga, Espanha Nelma Regina Segnini Bossolan, Instituto de Física de São Carlos, Universidade de São Paulo - USP, Brasil Paulo De Avila
Andres Velasco; Alejandro Neut
We revisit the question of what determines the credibility of macroeconomic policies here, of promises to repay public debt. Almost all thinking on the issue has focused on governments' strategic decision to default (or erode the value of outstanding debt via inflation/devaluation). But sometimes governments default not because they want to, but because they cannot avoid it: adverse shocks leave them no option. We build a model in which default/devaluation can occur deliberately (for strategi...
Broome, André; Seabrooke, Leonard
provide a conceptual framework for understanding how IOs seek to use their own cognitive authority to foster ‘diagnostic coordination’ across technocratic economic policy communities. This encourages officials to adapt to a common policy language and delimits the policy space within which they identify......International organizations (IOs) such as the International Monetary Fund and the World Bank are assumed to rely on ‘sympathetic interlocutors’ at the national level to drive through economic reforms that conform to global policy norms. In this article we answer the following question: How do...... sympathetic interlocutors for IOs emerge in the first place? We address this question by examining how IOs engage in teaching norms to national officials via transnational policy training in order to increase the number of domestic reformers who are sympathetic to their prescriptions for policy change. We...
On October 27, 1986, the Science and Technology Agency released the result of a survey on the nuclear research and development in private industry. This has been conducted as a part of the annual general survey on the development and utilization of atomic energy. There were a number of research and development projects having reached the stage of commercialization, and the need to draw on the resources of private industry for the research and development of atomic energy was increasingly recognized. The Agency believes that an overall picture of the research and development in private industry will provide with information required for the formation of future policy. The survey revealed 367 billion yen as the total research and development spending related to atomic energy, including 256 billion yen of government fund and 111 billion yen of private industry. The spending for reactors and equipment accounted for 63.7 % of the total spending. The method of survey and the results, such as the sales of nuclear equipment supply industry and the present situation of nuclear research and development, are reported. The nuclear equipment supply industry places much weight on the research and development, for which the investment ratio reached 4.5 %. (Kako, I.)
Stolberg, H.O.; Nahmias, C.
Canadian radiologists were informed by the press on Mar. 17, 2001, about an important initiative of their national organization. The CAR had commissioned a Montreal law firm to provide a legal opinion about the use of 'obsolete equipment'. The lawyer of the law firm opined that 'it is imperative that the patient be advised and understand the risks and uncertainties associated with the reliability of such an examination'. The 5-page legal opinion (available at www.car.ca) also recommended that radiologists inform patients that they should consider shopping around for a hospital or clinic with newer machines, even if it means travelling out of the country. When summarizing the legal advice for the media, the Chief Executive Officer of the CAR said radiologists should advise patients if better equipment is available in other facilities, including 'private facilities', or in other jurisdictions, such as the United States. These developments should be of great concern to Canadian radiologists who are well aware of the problems associated with aging equipment and the lack of and limited access to newer imaging modalities. The legal initiative of the CAR, however, makes it imperative for individual radiologists to provide comments and for the CAR executive to answer a number of questions and address a number of priorities, including the following. (author)
Yang, Myung Seung; Park, J.J.; Lee, J.W.; Kim, S.S.; Yim, S.P.; Kim, J.H.; Kim, K.H.; Na, S.H.; Kim, W.K.; Shin, J.M.; Lee, D.Y.; Cho, K.H.; Lee, Y.S.; Sohn, J.S.; Kim, M.J.
In this study, DUPIC powder and pellet fabrication equipment, welding system, QC equipment, and fission gas treatment are developed to fabricate DUPIC fuel at IMEF M6 hot cell. The systems are improved to be suitable for remote operation and maintenance with the manipulator at hot cell. Powder and pellet fabrication equipment have been recently developed. The systems are under performance test to check remote operation and maintenance. Welding chamber and jigs are designed and developed to remotely weld DUPIC fuel rod with manipulators at hot cell. Remote quality control equipment are being tested for analysis and inspection of DUPIC fuel characteristics at hot cell. And trapping characteristics is analyzed for cesium and ruthenium released under oxidation/reduction and sintering processes. The design criteria and process flow diagram of fission gas treatment system are prepared incorporating the experimental results. The fission gas treatment system has been successfully manufactured. (Author). 33 refs., 14 tabs., 91 figs
Broek, T. van den; Giessen, A.M. van der
The goal of this study is to highlight possible future developments of importance to the electrical and optical (E&O) equipment sector, paying particular importance to ‘radical’ changes and discussing policy options and future scenarios. The electrical & optical equipment sector plays a vital role
The Containment and Surveillance Equipment Compendium contains information sections describing the application and status of seals, optical surveillance systems, and monitors for international safeguards systems. The Compendium is a collection of information on equipment in use (generally by the IAEA) or under development in the US in diverse programs being conducted at numerous facilities under different sponsors. The Compendium establishes a baseline for the status and applications of C/S equipment and is a tool to assist in the planning of future C/S hardware development activities. The Appendix contains design concepts which can be developed to meet future goals
The objective and the scope of this document are to list and briefly describe the major mobile equipment necessary for waste package (WP) Transport and Emplacement in the proposed subsurface nuclear waste repository at Yucca Mountain. Primary performance characteristics and some specialized design features of the equipment are explained and summarized in the individual subsections of this document. The Transport and Emplacement equipment described in this document consists of the following: (1) WP Transporter; (2) Reusable Rail Car; (3) Emplacement Gantry; (4) Gantry Carrier; and (5) Transport Locomotive
... conform with this part. (Passenger cars and other passenger equipment classified as locomotives under part... equipment, or an automated tracking system is provided, with the following information about the defective passenger equipment: (i) The reporting mark and car or locomotive number; (ii) The name of the inspecting...
Federal Communications Commission — EAS (Equipment Authorization System). Radio Frequency (RF) devices are required to be properly authorized under 47 CFR Part 2 prior to being marketed or imported...
Millennium Challenge Corporation — Evaluation design The impact evaluation sought to identify the causal impact of exposure to equipment upgrades on subsequent outcomes. Insofar as we were not able to...
... Health and Human Services U.S. Food and Drug Administration A to Z Index Follow FDA En ... Devices Products and Medical Procedures General Hospital Devices and Supplies Personal Protective Equipment for Infection ...
U.S. Environmental Protection Agency — Certified models meet all ENERGY STAR requirements as listed in the Version 2.0 ENERGY STAR Program Requirements for Imaging Equipment that are effective as of...
Macdonell, Alexander Thomas [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Meierbachtol, Krista Cruse [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Evans, James Walter Jr. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Mayo, Douglas R. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)
Electromagnetic radiation (EMR) emission strength measurements were performed on a suite of passive non-destructive assay (NDA) radiation detection equipment. Data were collected from 9 kHz up to 6 GHz on each of the assembled systems.
Hinerman, K.B.; Smith, R.E.
Under DOE contract, Dalton-Dalton-Newport, Inc. is performing an engineering evaluation of three selected FUSRAP sites in an effort to generate equipment concepts to perform remedial action for retrieval, packaging, storing, and transporting contaminated soil and other debris. Along with this engineering evaluation, an analysis of state and Federal regulations was made which had significant impact on the selected equipment and costs for each remedial action concept
Gaestel, P.; Guesnon, H.; Sauze, G.
In order to enhance the reactor availability, several improvements on reactor equipment have been developed: design optimization for stator maintenance replacement in the main alternator; adjustment modification of stator coils in the main alternator for an easier maintenance; improvement of the fuel handling line (pole crane, transfer equipment, loading machine); development of a loose part trapping system in the steam generator secondary circuit. 1 tab
Remus, L.; Colling, J.M.; Buisson, J.
The use of the programmed digital techniques in systems important to safety led to developing equipment line-ups which allow to procedure, through using a restricted number of sub-assemblies, a variety of facilities capable of performing diversified functions. Upon remembering the requirements that such equipments are required to meet, the equipments produced by Merlin Gerin are described in this paper. Such equipments include a whole set of printed circuit boards, plug-in units with self-engaging connectors and the related cabinets to accommodate them. The following systems are made up of such equipments: digital integrated protection system, rod control and monitoring system, reactor power distribution monitoring equipment [fr
Full Text Available This article presents scaling rules developed to predict the response of submarine equipment subjected to underwater chemical explosions. The computer was used as a surrogate for shock tests. A simplified model of a hull section was used to contain frame-mounted single degree of freedom equipment. A general scaling rule has been developed to handle the spread in the shock response attributable to the charge weight, equipment weight, and equipment frequency, where the shock response is the absolute maximum acceleration of the equipment mass as a function of the shock factor for a given charge weight. The article also examines those cases where a new hull is derived from an original hull by the linear scaling law. The solution of the shock response is well known when the internal equipment has also been linearly scaled. A new general scaling rule is developed for those cases when the equipment is not linearly scaled, that is, the equipment and charge weight used with the original hull remains unchanged when installed in the linearly scaled hull or a completely different equipment and charge weight are used with the new hull. It is emphasized that the test sections were short and devoid of typical equipment present in a real compartment. The results, nevertheless, provide trends and ratios in shock design values, not necessarily absolute design numbers. The approach taken in developing these scaling rules could be useful for enhancing field data that may exist for a given class of boat to allow greater usage of these data for different equipment subject to a variety of charge weights, attack geometries, and other boats.
... Department of Defense OFFICE OF THE SECRETARY OF DEFENSE DEFENSE CONTRACTING RECOUPMENT OF NONRECURRING COSTS ON SALES OF U.S. ITEMS § 165.4 Policy. It is DoD policy that: (a) A nonrecurring cost recoupment charge shall be imposed for sales of major defense equipment only as required by Act of Congress (e.g...
...) When acquiring replacement equipment, the recipient may use the equipment to be replaced as trade-in or sell the equipment and use the proceeds to offset the costs of the replacement equipment subject to the... 28 Judicial Administration 2 2010-07-01 2010-07-01 false Equipment. 70.34 Section 70.34 Judicial...
... acquiring replacement equipment, the recipient may use the equipment to be replaced as trade-in or sell the equipment and use the proceeds to offset the costs of the replacement equipment subject to the approval of... 14 Aeronautics and Space 5 2010-01-01 2010-01-01 false Equipment. 1260.134 Section 1260.134...
...) When acquiring replacement equipment, the grantee or subgrantee may use the equipment to be replaced as... equipment (including replacement equipment), whether acquired in whole or in part with grant funds, until... established to ensure the highest possible return. (e) Disposition. When original or replacement equipment...
...) When acquiring replacement equipment, the grantee or subgrantee may use the equipment to be replaced as... equipment (including replacement equipment), whether acquired in whole or in part with grant funds, until... established to ensure the highest possible return. (e) Disposition. When original or replacement equipment...
...) When acquiring replacement equipment, the grantee or subgrantee may use the equipment to be replaced as... equipment (including replacement equipment), whether acquired in whole or in part with grant funds, until... established to ensure the highest possible return. (e) Disposition. When original or replacement equipment...
...) When acquiring replacement equipment, the recipient may use the equipment to be replaced as trade-in or sell the equipment and use the proceeds to offset the costs of the replacement equipment subject to the... 43 Public Lands: Interior 1 2010-10-01 2010-10-01 false Equipment. 12.934 Section 12.934 Public...
... income. (e) When acquiring replacement equipment, the recipient may use the equipment to be replaced as trade-in or sell the equipment and use the proceeds to offset the costs of the replacement equipment... 24 Housing and Urban Development 1 2010-04-01 2010-04-01 false Equipment. 84.34 Section 84.34...
...) When acquiring replacement equipment, the recipient may use the equipment to be replaced as trade-in or sell the equipment and use the proceeds to offset the costs of the replacement equipment subject to the... 38 Pensions, Bonuses, and Veterans' Relief 2 2010-07-01 2010-07-01 false Equipment. 49.34 Section...
.... (4) When acquiring replacement equipment, the grantee or subgrantee may use the equipment to be... managing equipment (including replacement equipment), whether acquired in whole or in part with grant funds... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Equipment. 105-71.132...
...) When acquiring replacement equipment, the recipient may use the equipment to be replaced as trade-in or sell the equipment and use the proceeds to offset the costs of the replacement equipment subject to the... 2 Grants and Agreements 1 2010-01-01 2010-01-01 false Equipment. 215.34 Section 215.34 Grants and...
growth and training of neuronal neural networks to control robot arms. This work was done to learn the properties of the neurons and neuronal network , by...Equipment to Support Development of Neuronal Network Controlled Robots With this award, our team purchased an ALA 2-channel stimulus generator, an...peer-reviewed journals: Number of Papers published in non peer-reviewed journals: Final Report: Equipment to Support Development of Neuronal Network
FINANCIAL REPORTING OF DEPARTMENT 97-FUNDED PROPERTY, PLANT, AND EQUIPMENT Report No. D-2001-039 January 31, 2001...from... to) ("DD MON YYYY") Title and Subtitle Financial Reporting of Department 97-Funded Property, Plant, and Equipment Contract or Grant Number...include financial statements for a reporting entity entitled inOther Defense Organizations-General Fund.lz The entity represents a consolidation of
Full text: The need for a top-down Safeguards Strategy to focus departmental objectives was recognized by the Programme Performance Appraisal System (PPAS) performed on the Equipment Development Project in 1999. The Department of Safeguards prepared at the end of 2000 a 5-year Strategic Plan to identify the changes and improvements expected to take place over the 2001-2005 period. Those Strategic Objectives were supposed to be used to properly plan IAEA Safeguards activities and define appropriate and coherent R and D programmes. The present paper describes the strategic directions that the IAEA will follow in the area of equipment development in order to meet the Safeguards Department long-term objectives for 2001-2005. The paper, which is derived from the IAEA Strategic Equipment Development Plan, prepared by the Division of Technical Support, includes two parts: general principles and policies applicable to all equipment development tasks; specific strategic guidance. The paper will not describe the detailed plans which are prepared based on the strategic plan on a biannual basis. Equipment development activities have been divided in five major projects (NDA, Seals, Surveillance, Unattended Monitoring and Remote Monitoring). Strategic directions for each of these projects will be described in the paper. Separate sections will deal with equipment development strategic guidance in the area of additional protocol inspections, JNFL projects, illicit trafficking and Trilateral Initiative. (author)
Laruelle, Ph.; Snegaroff, Th.; Moreau, S.; Tellenne, C.; Brunel, S.
Fourth chapter of the book on the geo-policy of the sustainable development, this chapter deal with the different and international policies concerned by the problem. The authors analyze the american energy attitude and policy, the economical equilibrium facing the environmental equilibrium for the european policy, the sanctified and sacrificed nature and the japanese attitude, India and China, the great fear of the 21 century and the sustainable development in Africa. (A.L.B.)
Ketteler, T; Krahwinkel, W; Gödke, J; Wolfertz, J; Scheuble, L; Hoffmeister, T; Gülker, H
In recent years, stress echocardiography has gained broad acceptance as a non-invasive method for the diagnosis of coronary artery disease. Facing different protocols, dosages and instrumentation, official guidelines for the performance, standardization and quality control of stress echocardiograms are needed; however, so far they are not available. This paper recommends the type of personnel and technical equipment needed for stress echocardiography laboratories, based on experience gained during more than 2000 stress echocardiographic procedures. To perform stress echocardiography, a cardiologist and a technical assistant--both well trained over a large number of tests--should be involved. The laboratory must have basic equipment such as a 12-lead ECG, blood pressure monitoring capacity, a treadmill or bicycle for ergometry, a precision intravenous delivery system for pharmacological stress testing as well as an adequate echo table; additionally, emergency equipment is mandatory. The ultrasound machine should contain transducers with high 2-D resolution; most important is a digital image acquisition system which facilitates performance and interpretation through side-by-side display of synchronized rest and stress images. Finally, there is a need for proper patient preparation and the obtaining of informed consent.
At the request of the Department of Energy (DOE)(EM-50), the Scientific Computing Unit developed a prototype system to track information and data relevant to equipment and tooling removed during decontamination and decommissioning activities. The DDETS proof-of-concept tracking system utilizes a one-dimensional (1D) and two-dimensional (2D) bar coding technology to retain and track information such as identification number, manufacturer, requisition information, and various contaminant information, etc. The information is encoded in a bar code, printed on a label and can be attached to corresponding equipment. The DDETS was developed using a proven relational database management system which allows the addition, modification, printing, and deletion of data. In addition, communication interfaces with bar code printers and bar code readers were developed. Additional features of the system include: (a) Four different reports available for the user (REAPS, transaction, and two inventory), (b) Remote automated inventory tracking capabilities, (c) Remote automated inventory tracking capability (2D bar codes allow equipment to be scanned/tracked without being linked to the DDETS database), (d) Edit, update, delete, and query capabilities, (e) On-line bar code label printing utility (data from 2D bar codes can be scanned directly into the data base simplifying data entry), and (f) Automated data backup utility. Compatibility with the Reportable Excess Automated Property System (REAPS) to upload data from DDETS is planned
Jensen, Lucas Roald Dörig; Fundal, Erling; Møller, Per
-resistant high chromium white cast iron (21988/JN/HBW555XCr21), a heat-treated wear resistant steel (Hardox 400) and a plain carbon construction steel (S235). Quartz, which accounts for the largest wear loss in the cement industry, was chosen as abrasive. Other process parameters such as velocity (1–7 m....../s) and pressure (70–1400 kPa) were chosen to closely imitate real industrial processes. The authors are aware that a number of wear mechanisms such as erosion, fatigue and abrasion may occur simultaneously in comminution equipment. Nonetheless, this paper aims at discussing abrasion only due to its large...
... Applications and Authorizations § 18.203 Equipment authorization. (a) Consumer ISM equipment, unless otherwise... ISM equipment shall be subject to verification, in accordance with the relevant sections of part 2...
Ouedraogo, Abdoulaye; Tosun, Mehmet S.; Yang, Jingjing
There have been significant changes in both the fertility rates and fertility perception since 1970s. In this paper, we examine the relationship between government policies towards fertility and the fertility trends. Total fertility rate, defined as the number of children per woman, is used as the main fertility trend variable. We use panel data from the United Nations World Population Policies database, and the World Bank World Development Indicators for the period 1976 through 2013. We find...
An inventory of the test equipment of the AVM Branch ''Acoustic and Vibratory Mechanics Analysis Methods'' group has been undertaken. The purpose of this inventory is to enable better acquaintance with the technical characteristics of the equipment, providing an accurate definition of their functionalities, ad to inform potential users of the possibilities and equipment available in this field. The report first summarizes the various experimental surveys conduced. Then, using the AVM equipment database to draw up an exhaustive list of available equipment, it provides a full-scope picture of the vibration measurement systems (sensors, conditioners and exciters) and data processing resources commonly used on industrial sites and in laboratories. A definition is also given of a mobile test unit, called 'shelter', and a test bench used for the testing and performance rating of the experimental analysis methods developed by the group. The report concludes with a description of two fixed installations: - the calibration bench ensuring the requisite quality level for the vibration measurement systems ; - the training bench, whereby know-how acquired in the field in the field of measurement and experimental analysis processes is made available to others. (author). 27 refs., 15 figs., 2 appends
Sirisena, K.; Peltoranta, M.; Goussarov, V.; Vodrazka, P.
SGTCS is responsible for monitoring and reporting the performance of the SG equipment. Performance monitoring (PM) has been implemented in most important safeguards equipment operating unattended in nuclear facilities. Inspectors acquire equipment performance data in facilities. After inspection, the data package is submitted to SGTCS for processing and analysis. The performance data is used for identification of systems or components, which should be changed in the field and for identification of modules which, should be diagnosed at HQ in order to determine the cause of failure. Moreover, the performance data is used for preventive maintenance and spares distribution planning, and to provide statistics for official reports and management decision making. An important part of the performance monitoring is reporting. Equipment performance reports contain information about equipment inventory, utilization, failure types, failure distribution, and reliability. Trends in performance are given in graphical form in cases, where past data is available. Reliability estimates such as expected times between failures are provided. The automated reporting tools are obtainable through EMIS database application. (author)
Redmond, J.; Carret, L.; Shaon, S.; Schultz, C.
The procurement engineering resources at Nuclear Power Plants (NPPs) are experiencing increasing backlog for procurement items primarily due to the inability to order the original replacement parts. The level of effort and time required to prepare procurement packages is increasing since the number of obsolete parts are increasing exponentially. Procurement packages for obsolete components and parts are much more complex and take more time to prepare because of the need to perform equivalency evaluations, testing requirements and test acceptance criteria development, commercial grade dedication or equipment qualification, and increasing efforts to verify that no fraudulent or counterfeit parts are procured. This problem will be further compounded when NPPs pursue license renewal and approval for plant-life extension. Advanced planning and advanced knowledge of equipment obsolescence is required to allow for sufficient time to properly procure replacement parts for obsolete items. The uncertain supply chain capability due to obsolescence is a real problem and can cause a risk to reliable plant operations due to the potential for a lack of available spare parts and replacement components to support outages and unplanned component failures. Advanced notification of obsolescence is increasingly more important to ensure that adequate time and planning is scheduled to procure the proper replacement parts. A thorough analysis of Original Equipment Manufacturer (OEM) availability and inventory as well as an analysis of failure rates and usage rates is required to predict critical part needs to allow for early identification of obsolescence issues so that a planned and controlled strategy to qualify replacement equipment can be implemented. (Author)
Tian, Tian [National Renewable Energy Lab. (NREL), Golden, CO (United States); Liu, Chang [National Renewable Energy Lab. (NREL), Golden, CO (United States); O' Shaughnessy, Eric [National Renewable Energy Lab. (NREL), Golden, CO (United States); Mathur, Shivani [National Renewable Energy Lab. (NREL), Golden, CO (United States); Holm, Alison [National Renewable Energy Lab. (NREL), Golden, CO (United States); Miller, John [National Renewable Energy Lab. (NREL), Golden, CO (United States)
The midscale market for solar photovoltaics (PV) has not experienced the same high growth rate as residential- or utility-scale market segments in the past five years when solar PV deployment increased rapidly. Midscale solar can be defined as behind-the-meter solar PV between 50 kilowatts and 2 megawatts adopted by multi-housing residential, commercial, industrial, non-profit, and other entities. A number of challenges face the midscale segment, including difficulties in contracting, mismatch between tenant lease and PV financing terms, high transaction costs relative to project sizes, and inefficiencies in matching prospective projects with capital. The changing policy landscape across U.S. states provides both opportunities and challenges to midmarket solar. Some states, such as California, are expanding system capacity limits for policies such as net metering, thus enabling a wider range of customers to benefit from excess generation. A number of states and utilities are making changes to rate design to introduce new or higher user fees for solar customers or reduced tariffs for net metering, which decrease the value of solar generation. An understanding of these policies relative to project feasibility and economics is important for prospective customers to make informed decisions to adopt solar PV. This guide complements existing solar policy resources to help potential customers navigate through the policy landscape in order to make informed decisions for their solar investment. The first part of this guide introduces the key solar policies necessary for policy-based decision-making, which involves using knowledge of a solar policy to improve project economics and efficiency. Policies that could result in policy-based decisions include interconnection standards, net metering, user fees, incentives, and third-party ownership policies. The goal of this section is to equip prospective customers and project developers with the tools necessary to understand and
On Thursday 27 February, CERN was pleased to donate computer equipment to a physics institute in the Philippines. H.E. Leslie J. Baja and Rolf Heuer. Following donations of computer equipment to institutes in Morocco, Ghana, Bulgaria, Serbia and Egypt, CERN is to send 50 servers and 4 network switches to the National Institute of Physics at the University of the Philippines Diliman. CERN’s Director-General Rolf Heuer and the Ambassador of the Philippines to Switzerland and Lichtenstein, H.E. Leslie J. Baja, spoke of their enthusiasm for the project during an official ceremony. The equipment will be used for various high energy physics research programmes in the Philippines and for the University’s development of digital resources for science.
Bigum, Marianne Kristine Kjærgaard; Christensen, Thomas Højlund
Waste electrical and electronic equipment (WEEE) is one of the fastest growing special waste types with an estimated growth of 3–5% per year (Cui and Forssberg, 2003). WEEE is a very heterogeneous waste type that contains many compounds that are considered to be harmful to both humans and the env......Waste electrical and electronic equipment (WEEE) is one of the fastest growing special waste types with an estimated growth of 3–5% per year (Cui and Forssberg, 2003). WEEE is a very heterogeneous waste type that contains many compounds that are considered to be harmful to both humans...
Purves, Lloyd R.
Special-purpose sets of equipment, packaged in identical modules with identical interconnecting mechanisms, attached to or detached from each other by specially designed robot, according to proposal. Two-arm walking robot connects and disconnects modules, operating either autonomously or under remote supervision. Robot walks along row of connected modules by grasping successive attachment subassemblies in hand-over-hand motion. Intended application for facility or station in outer space; robot reconfiguration scheme makes it unnecessary for astronauts to venture outside spacecraft or space station. Concept proves useful on Earth in assembly, disassembly, or reconfiguration of equipment in such hostile environments as underwater, near active volcanoes, or in industrial process streams.
Sherry, A; Cruddace, AE
Modern Power Station Practice, Volume 3: Mechanical (Turbines and Auxiliary Equipment) focuses on the development of turbines and auxiliary equipment used in power stations in Great Britain. Topics covered include thermodynamics and steam turbine theory; turbine auxiliary systems such as lubrication systems, feed water heating systems, and the condenser and cooling water plants. Miscellaneous station services, and pipework in power plants are also described. This book is comprised of five chapters and begins with an overview of thermodynamics and steam turbine theory, paying particular attenti
Ditlevsen, Kia; Reventlow, Susanne; Nielsen, Annemette Ljungdalh
visitors and which complicate implementation of the policies of the Danish health authorities. Findings show that the current system is not well equipped to treat early overweight. A gap in primary preventive health care for children at age 3–5, indistinct lines of responsibility, inadequate cooperation......, and lack of resources together make it difficult for health care professionals to initiate interventions and reach the children in need of support. By analyzing the policy implementation process in a theoretical framework that discloses the discursive allocation of responsibilities, the study is able...... to provide a deeper description and analysis of the problem. The study makes it clear how preventive health care for overweight children rests on the negotiation of formal and performed responsibilities among health practitioners within a framework of scarce resources and communication deficit....
Higher Education Faculty in Mexico and the United States: Characteristics and Policy Issues. Understanding the Differences: A Working Paper Series on Higher Education in the U. S. and Mexico. Working Paper Number 2.
Lovell, Cheryl D.; Sanchez, Maria Dolores Soler
This working paper analyzes higher education faculty characteristics in Mexico and the United States. The first section describes and compares Mexican and U.S. faculty characteristics and conditions, including total number of faculty, student-teacher ratios, full- versus part-time status, rank, tenure, average salaries, gender and ethnicity, and…
Luo Gaorong [Organization of the United Nations, Beijing (China). International Centre of Small Hydroelectric Power Plants
This document presents a general overview on hydraulic turbines and auxiliary equipment, emphasizing the turbine classification, in accordance with the different types of turbines, standard turbine series in China, turbine selection based on the basic data required for the preliminary design, general hill model curves, chart of turbine series and the arrangement of application for hydraulic turbines, hydraulic turbine testing, and speed regulating device.
Miyagawa, Kazuo; Amano, Hiroshi
In the steel industry, though the investment in isotope-equipped measuring instruments is small as compared with that in machinery, they play important role in the moisture measurement in sintering and blast furnaces, the thickness measurement in rolling process and others in automatic control systems. The economic aspect of the isotope-equipped measuring instruments is described on the basis of the practices in Kimitsu Works of Nippon Steel Corporation: distribution of such instruments, evaluation of economic effects, usefulness evaluation in view of raising the accuracy, and usefulness evaluation viewed from the failure of the isotope instruments. The evaluation of economic effects was made under the premise that the isotope-equipped measuring instruments are not employed. Then, the effects of raising the accuracy are evaluated for a γ-ray plate thickness gauge and a neutron moisture gauge for coke in a blast furnace. Finally, the usefulness was evaluated, assuming possible failure of the isotope-equipped measuring instruments. (J.P.N.)
Curriculum Review, 2009
Gaming equipment (such as Nintendo's Wii[TM]) is making its way to schools and classrooms. However, most of the discussion regarding how to use this technology and integrate it into lesson plans is happening in blogs on the Internet. An advocate of interactive media in the classroom, Dr. Dawn Hawkins, a faculty member for the Art Institute of…
Bandyopadhyay, K.K.; Hofmayer, C.H.
Seismic fragility levels of safety-related electrical and mechanical equipment used in nuclear power plants are discussed. The fragility level is defined as the vibration level corresponding to initiation of equipment malfunctions. The test response spectrum is used as a measure of this vibration level. The fragility phenomenon of an equipment is represented by a number of response spectra corresponding to various failure modes. Analysis methods are described for determination of the fragility level by use of existing test data. Useful conversion factors are tabulated to transform test response spectra from one damping value to another. Results are presented for switch-gears and motor control centers. The capacity levels of these equipment assemblies are observed to be limited by malfunctioning of contactors, motor starters, relays and/or switches. The applicability of the fragility levels, determined in terms of test response spectra, to Seismic Margin Studies and Probabilistic Risk Assessments is discussed and specific recommendations are provided
This notice describes EPA policy on including telephone numbers and other access numbers or internet addresses, on pesticide product labeling. It also explains how the telephone number of the National Pesticide Information Center hotline may be used.
Coles, Henry; Greenberg, Steve
This report documents a demonstration of an electronic--equipment cooling system in the engineering prototype development stage that can be applied in data centers. The technology provides cooling by bringing a water--based cooling fluid into direct contact with high--heat--generating electronic components. This direct cooling system improves overall data center energy efficiency in three ways: High--heat--generating electronic components are more efficiently cooled directly using water, capturing a large portion of the total electronic equipment heat generated. This captured heat reduces the load on the less--efficient air--based data center room cooling systems. The combination contributes to the overall savings. The power consumption of the electronic equipment internal fans is significantly reduced when equipped with this cooling system. The temperature of the cooling water supplied to the direct cooling system can be much higher than that commonly provided by facility chilled water loops, and therefore can be produced with lower cooling infrastructure energy consumption and possibly compressor-free cooling. Providing opportunities for heat reuse is an additional benefit of this technology. The cooling system can be controlled to produce high return water temperatures while providing adequate component cooling. The demonstration was conducted in a data center located at Lawrence Berkeley National Laboratory in Berkeley, California. Thirty--eight servers equipped with the liquid cooling system and instrumented for energy measurements were placed in a single rack. Two unmodified servers of the same configuration, located in an adjacent rack, were used to provide a baseline. The demonstration characterized the fraction of heat removed by the direct cooling technology, quantified the energy savings for a number of cooling infrastructure scenarios, and provided information that could be used to investigate heat reuse opportunities. Thermal measurement data were used
... 46 Shipping 4 2010-10-01 2010-10-01 false Sounding equipment. 108.701 Section 108.701 Shipping... EQUIPMENT Miscellaneous Equipment § 108.701 Sounding equipment. Each self-propelled unit must have a mechanical or electronic sounding apparatus. ...
... as program income. (e) When acquiring replacement equipment, the recipient may use the equipment to... replacement equipment subject to the approval of the Secretary. (f) The recipient's property management... 34 Education 1 2010-07-01 2010-07-01 false Equipment. 74.34 Section 74.34 Education Office of the...
... contemplated by Federal statute. (4) When acquiring replacement equipment, the grantee or subgrantee may use.... Procedures for managing equipment (including replacement equipment), whether acquired in whole or in part... 20 Employees' Benefits 2 2010-04-01 2010-04-01 false Equipment. 437.32 Section 437.32 Employees...
... replacement equipment, the grantee or subgrantee may use the equipment to be replaced as a trade-in or sell... replacement equipment), whether acquired in whole or in part with grant funds, until disposition takes place... ensure the highest possible return. (e) Disposition. When original or replacement equipment acquired...
... contemplated by Federal statute. (4) When acquiring replacement equipment, the grantee or subgrantee may use... requirements. Procedures for managing equipment (including replacement equipment), whether acquired in whole or... original or replacement equipment acquired under a grant or subgrant is no longer needed for the original...
... contemplated by Federal statute. (4) When acquiring replacement equipment, the grantee or subgrantee may use... requirements. Procedures for managing equipment (including replacement equipment), whether acquired in whole or... original or replacement equipment acquired under a grant or subgrant is no longer needed for the original...
... treated as program income. (e) When acquiring replacement equipment, the recipient may use the equipment... replacement equipment subject to the approval of SSA. (f) The recipient's property management standards for... 20 Employees' Benefits 2 2010-04-01 2010-04-01 false Equipment. 435.34 Section 435.34 Employees...
... treated as program income. (e) When acquiring replacement equipment, the recipient may use the equipment... replacement equipment subject to the approval of the NHPRC. (f) The recipient's property management standards... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false Equipment. 1210.34 Section...
... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Equipment design. 58.61 Section 58.61 Food and... PRACTICE FOR NONCLINICAL LABORATORY STUDIES Equipment § 58.61 Equipment design. Equipment used in the... of appropriate design and adequate capacity to function according to the protocol and shall be...
... 40 Protection of Environment 31 2010-07-01 2010-07-01 true Equipment design. 792.61 Section 792.61...) GOOD LABORATORY PRACTICE STANDARDS Equipment § 792.61 Equipment design. Equipment used in the... of appropriate design and adequate capacity to function according to the protocol and shall be...
... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Equipment design. 160.61 Section 160... LABORATORY PRACTICE STANDARDS Equipment § 160.61 Equipment design. Equipment used in the generation... appropriate design and adequate capacity to function according to the protocol and shall be suitably located...
Wiesmeth, Hans; Häckl, Dennis
Holistic environmental policies, which emerged from a mere combination of technical activities in waste management some 40 years ago, constitute the most advanced level of environmental policies. These approaches to environmental policy, among them the policies in integrated waste management, attempt to guide economic agents to an environment-friendly behaviour. Nevertheless, current holistic policies in waste management, including policies on one-way drinks containers and waste electrical and electronic equipment, and implementations of extended producer responsibility with further applications to waste electrical and electronic equipment, reveal more or less severe deficiencies - despite some positive examples. This article relates these policy failures, which are not necessarily the result of an insufficient compliance with the regulations, to missing constitutive elements of what is going to be called an 'integrated environmental policy'. This article therefore investigates - mostly from a practical point of view - constitutive elements, which are necessary for a holistic policy to serve as a well-functioning allocation mechanism. As these constitutive elements result from a careful 'integration' of the environmental commodities into the economic allocation problems, we refer to these policies as 'integrated environmental policies'. The article also discusses and illustrates the main steps of designing such a policy - for waste electrical and electronic equipment and a (possible) ban of Glyphosat in agriculture. As these policies are dependent on economic and political stability with environmental awareness sufficiently developed, the article addresses mostly waste management policies in highly industrialised countries.
Woods, Dawn Marie; Ketterlin Geller, Leanne; Basaraba, Deni
A strong foundation in early number concepts is critical for students' future success in mathematics. Research suggests that visual representations, like a number line, support students' development of number sense by helping them create a mental representation of the order and magnitude of numbers. In addition, explicitly sequencing instruction…
Roberson, Judy A.; Webber, Carrie A.; McWhinney, Marla C.; Brown, Richard E.; Pinckard, Margaret J.; Busch, John F.
This research was conducted in support of two branches of the EPA ENERGY STAR program, whose overall goal is to reduce, through voluntary market-based means, the amount of carbon dioxide emitted in the U.S. The primary objective was to collect data for the ENERGY STAR Office Equipment program on the after-hours power state of computers, monitors, printers, copiers, scanners, fax machines, and multi-function devices. We also collected data for the ENERGY STAR Commercial Buildings branch on the types and amounts of ''miscellaneous'' plug-load equipment, a significant and growing end use that is not usually accounted for by building energy managers. This data set is the first of its kind that we know of, and is an important first step in characterizing miscellaneous plug loads in commercial buildings. The main purpose of this study is to supplement and update previous data we collected on the extent to which electronic office equipment is turned off or automatically enters a low power state when not in active use. In addition, it provides data on numbers and types of office equipment, and helps identify trends in office equipment usage patterns. These data improve our estimates of typical unit energy consumption and savings for each equipment type, and enables the ENERGY STAR Office Equipment program to focus future effort on products with the highest energy savings potential. This study expands our previous sample of office buildings in California and Washington DC to include education and health care facilities, and buildings in other states. We report data from twelve commercial buildings in California, Georgia, and Pennsylvania: two health care buildings, two large offices (> 500 employees each), three medium offices (50-500 employees), four education buildings, and one ''small office'' that is actually an aggregate of five small businesses. Two buildings are in the San Francisco Bay area of California, five are in
as with national and sub-national governments in Europe, all of them introducing interesting novelties in their innovation policy. These changes refer to different aspects of policy, mainly the content of policy initiatives towards science, technology and innovation; the instruments governments are using...... to achieve their goals; and the actors in the policy system that are being mobilised in pursuing these goals. This paper deals with these policy changes, paying special attention to the novelties introduced since the early 1990s in Europe. The perspective of this paper deals mainly on the changes introduced...... at the EU level, and mentions similar trends taking place at national and sub-national levels. The questions that guide the contents here are essentially three, namely, what are the main traits of innovation policies in Europe since the 1990s and how have the EU and different national governments approached...
In this thesis we model and analyze several environmental policies in an existing mathematical representation of a perfectly competitive electricity market. We contribute to the literature by theoretically and numerically establishing a number of effects of environmental policies on investment
cation technology (ICT) and now. Minister of Science and Technology, was one of the architects of Mozam- bique's ICT policy in 2000 — the first in Africa. Nationwide access to these technologies is one of the pillars of the government's science and technology policy. “We don't believe in politicians, but we believe in politics.
Health policy has great influence on the daily work of every cardiologist. The influence of progress of practical cardiology on health policy in our country on the one hand and the influence of health policy on cardiology on the other hand are discussed, In the 1970s cardiac rehabilitation in special rehabilitation clinics was developed as a consequence of the usual therapy at that time with longer periods of bedrest and late invasive diagnostic procedures. Patients got a right on rehabilitation by law. However, in the 1980s the increasing number of rehabilitation clinics in our country and their budgets caused the first controversial discussion on health policy in our society, which was primarily thought to be a scientific one. At that time one of the first guidelines of the Commission of Clinical Cardiology as to coronary dilatation demanded in necessity of immediate cardiac surgery. To get more influence on the ongoing discussion the group of chief clinical cardiologists founded their own working group which had later on considerable influence on policy and scientific work of our society. Overall, the awareness of the need for active health policy was developed relatively late. For instance, the register of nationwide heart catheterization procedures was started in the early 1980s but was not used to influence health policies, for establishment of new catheterization facilities. At present, the development of cardiology is limited by budget and total number of cardiac operations is reduced, so it is time to remember the highly effective conservative "soft" therapy of atherosclerosis with a combination of drugs and changing lifestyle which is well evaluated in prospective studies. It is time to apply and reevaluate the chances of primary and secondary prevention of atherosclerosis and heart insufficiency. New non-invasive techniques as MRT and PET and therapeutic techniques as genetic or stem cell therapy will influence cost and health policy in the near future.
Khan, Raja S. R.
This thesis looks at creating a multidisciplinary simulation tool for rotating plant equipment selection, specifically gas turbines, for the liquefaction of natural gas (LNG). This is a collaborative project between Shell Global Solutions and Cranfield University in the UK. The TERA LNG tool uses a Techno-economic, Environmental and Risk Analysis (TERA) approach in order to satisfy the multidisciplinary nature of the investigation. The benefits of the tool are to act as an aid ...
Safety margins related to design of reactor equipment are defined according to safety regulations. Advanced best estimate methods are proposed including some examples which were computed and compared to experimental results. Best estimate methods require greater computation effort and more material data but give better variable accuracy and need careful experimental validation. Simplified methods compared to the previous are less sensitive to material data, sometimes are more accurate but very long to elaborate
Shin, Sung Min; Jeon, In Seop; Kang, Hyun Gook
The core damage frequency (CDF) of operating and constructing pressurized nuclear plants are ranging on the order of 10 -5 and 10 -6 per year. The target CDF of new NPP design has been set at 10 -7 . In this context, although various systems are currently studied, availability improvement of standby equipment will be more efficient than the additional application of safety systems. It is obvious in every aspect, such as management and cost efficiency. Here, soundness can affect equipment unavailability, and the soundness degrades because of aging. However, some studies did not consider aging when calculating the unavailability. Standby equipment can age because of two important factors: standby stress which accumulates over time, and test stress which accumulates with the number of tests (or operations). Both factors should be considered together when aging is considered. However, some studies only considered standby stress or test stress. There are some previous studies which considered both factors. Besides equipment soundness related to aging effect, some process like bypass during test also can affect equipment unavailability because the original function of equipment cannot be performed immediately during this process. However, there are seldom studies dealing with above factors as a whole problem. This study investigated a general approach to calculate the unavailability of standby equipment which considers aging caused by standby and test stresses and bypass process. Based on this general approach, we propose two maintenance strategies which aim to reduce standby equipment unavailability. In section 2, the general approach is presented. As one of the strategies, the changing test interval method (CIM) is introduced in section 3, and its effectiveness is also analyzed. The online monitoring method (OMM) is investigated in section 4 as another method to reduce equipment unavailability. In section 5, a combination of these two methods is analyzed. A general
Chafel, Judith A., Ed.
This collection documents how far we still are in the United States from putting our knowledge about child well being and policy into practice. It provides an overview of the changing nature of child poverty in the United States through the contributions of authors who use a number of qualitative and quantitative approaches to look at children in…
This is a listing of energy related equipment available through the Energy-Related Laboratory Equipment Grant Program which grants used equipment to institutions of higher education for energy-related research. Information included is an overview of the program, how to apply for a grant of equipment, eligibility requirements, types of equipment available, and the costs for the institution.
Drygin, Michael; Kuryshkin, Nicholas
The article tells about forming a new concept of scheduled preventive repair system of the equipment at coal mining enterprises, based on the use of modem non-destructive evaluation methods. The approach to the solution for this task is based on the system-oriented analysis of the regulatory documentation, non-destructive evaluation methods and means, experimental studies with compilation of statistics and subsequent grapho-analytical analysis. The main result of the work is a feasible explanation of using non-destructive evaluation methods within the current scheduled preventive repair system, their high efficiency and the potential of gradual transition to condition-based maintenance. In practice wide use of nondestructive evaluation means w;ill allow to reduce significantly the number of equipment failures and to repair only the nodes in pre-accident condition. Considering the import phase-out policy, the solution for this task will allow to adapt the SPR system to Russian market economy conditions and give the opportunity of commercial move by reducing the expenses for maintenance of Russian-made and imported equipment.
Cooney, P.; Rajan, J.; Malone, J.F.; Gavin, G.
With the advent of the EC Patient Directive, the importance of surveying and optimising patient exposure for diagnostic imaging procedures is paramount. In the field of dentistry there has been a heightened interest in areas of equipment performance and patient exposure. This interest, coupled with a number of dental radiation safety incidents investigated by our department, and the issuing of a Code of Practice for Radiological Protection in Dentistry by the Department of Health, led to the establishment in our department, of an evaluation protocol for the performance and operation of dental X ray equipment. The protocol was used to perform a survey on over 100 dental X ray units in use in the Public Sector in Ireland. This presentation will report on the radiation incidents mentioned above. It will detail the protocol and furnish the results and conclusions of the survey. The survey has made it possible to establish clearly the necessary steps required to ensure compliance with requirements. In addition, the corrective steps taken by the dental authorities will be presented and the overall impact of the regulations and the programme consequent on them will be reviewed. (Author)
Holmes, Jon L.
The Equipment Buyers Guide was edited by Jo Rita Jordan. The new Equipment Buyers Guide, bound into the back of this issue, is also a new resource of JCE Internet. This resource provides an online source for the information contained in the printed guide. Placing this information online allows us to regularly update it and to provide live links to the suppliers' WWW sites. The organization of the online version parallels that of the print version. There is an alphabetical list of suppliers and a categorical listing. Links to these lists are provided on every page in the left-hand navigation bar. To quickly find information about a particular supplier, you click Supplier List, click the letter that begins the supplier's name, and scroll through the list to find the supplier. To find which suppliers provide a particular type of instrument or equipment, use the Categories link; click the category of the equipment you are looking for and then click the link to a supplier. You will then be taken to an alphabetical supplier listing page where you can scroll until you find the particular supplier of the item for which you are looking. Once you have found a supplier, the online Equipment Buyers Guide gives you the traditional contact information. But in addition, you also get one-click access to the WWW sites of the suppliers that have them. Depending on the site, you should be able to find information about the items that you seek and may even be able to order the items online! We think that you will find the online version of the Equipment Buyers Guide useful. To make it more useful, please send your suggestions, any errors or omissions you find, and any additional categories to the editor at firstname.lastname@example.org The online Equipment Buyers Guide can be found at JCE Online at http://JChemEd.chem.wisc.edu/JCEWWW/Resources/EBG/ JCE Online in '99 JCE Online is your online source of "all things JCE". In order to provide you with an even more useful online resource, JCE
Full text: The Scientific Equipment Division consists of the Design Group and the Mechanical Workshop. The activity of the Division includes the following: * designs of devices and equipment for experiments in physics; their mechanical construction and assembly. In particular, these are vacuum chambers and installations for HV and UHV;* maintenance and upgrading of the existing installations and equipment in our Institute; * participation of our engineers and technicians in design works, equipment assembly and maintenance for experiments in foreign laboratories. The Design Group is equipped with PC-computers and AutoCAD graphic software (release 2000 and Mechanical Desktop 4.0) and an A0 plotter, which allow us to make drawings and 2- and 3-dimensional mechanical documentation to the world standards. The Mechanical Workshop offers a wide range of machining and treatment methods with satisfactory tolerances and surface quality. They include: * turning - cylindrical elements of a length up to 2000 mm and a diameter up to 400 mm, and also disc type elements of a diameter up to 600 mm and a length not exceeding 300 mm, * milling - elements of length up to 1000 mm and gear wheels of diameter up to 300 mm, * grinding - flat surfaces of dimensions up to 300 mm x 1000 mm and cylindrical elements of a diameter up to 200 mm and a length up to 800 mm, * drilling - holes of a diameter up to 50 mm, * welding - electrical and gas welding, including TIG vacuum-tight welding, * soft and hard soldering, * mechanical works including precision engineering, * plastics treatment - machining and polishing using diamond milling, modelling, lamination of various shapes and materials, including plexiglas, scintillators and light-guides, * painting - paint spraying with possibility of using furnace-fired drier of internal dimensions of 800 mm x 800 mm x 800 mm. Our workshop is equipped with the CNC milling machine which can be used for machining of work pieces up to 500 kg. The machine
Verdaasdonk, E.G.G.; Stassen, L.P.S.; Hoffmann, W.F.; Van der Elst, M.; Dankelman, J.
Background A high incidence of problems with the technical equipment is known to occur during routine laparoscopic procedures. Use of a structured checklist of preparatory measures could help to prevent these problems. This study aimed to determine the extent to which a checklist reduced the number
... Standards for Hazardous Air Pollutant Emissions: Group IV Polymers and Resins § 63.1331 Equipment leak... polymer fluid used to provide lubrication and/or cooling of the pump or agitator shaft exits the pump... identification numbers as would otherwise be required under § 63.181(b)(1)(i) or § 63.181(b)(4). (iv) When...
FACILITIES ITEM REQUIREMENT Material-handling equipment (MHE) Offload and load test item from transportation asset. Maintenance shop Accomplish Technical... Automotive road courses Accomplish road transport durability and reliability road missions. ** Superscript numbers correspond to Appendix E, References...verify that it is fully functional. All faults will be identified and recorded. Any corrective actions and replacement parts required to repair the
Rahman, Nurhaidar; Kuala, S. I.; Tribowo, R. I.; Anggara, C. E. W.; Susanti, N. D.
Automatic control equipment has been made for the nutrient content in irrigation water for hydroponic plants. Automatic control equipment with CCT53200E conductivity controller to nutrient content in irrigation water for hydroponic plants, can be used to control the amount of TDS of nutrient solution in the range of TDS numbers that can be set according to the range of TDS requirements for the growth of hydroponically cultivated crops. This equipment can minimize the work time of hydroponic crop cultivators. The equipment measurement range is set between 1260 ppm up to 1610 ppm for spinach plants. Caisim plants were included in this experiment along with spinach plants with a spinach plants TDS range. The average of TDS device is 1450 ppm, while manual (conventional) is 1610 ppm. Nutrient solution in TDS controller has pH 5,5 and temperature 29,2 °C, while manual is pH 5,6 and temperature 31,3 °C. Manually treatment to hydroponic plant crop, yields in an average of 39.6 grams/plant, greater than the yield of spinach plants with TDS control equipment, which is in an average of 24.6 grams / plant. The yield of caisim plants by manual treatment is in an average of 32.3 grams/crop, less than caisim crop yields with TDS control equipment, which is in an average of 49.4 grams/plant.
Generic CMYK printer profile Composite Default screen William B. Ruger Chair of National Security Economics Papers Number 4 American Foreign Policy...American comparative ad- vantage, including the liberalization of textile and agricultural policies in the United States, thereby leveling the playing
Ren, Carina Bregnholm; Rasmussen, Rasmus Kjærgaard
planning and execution and of event outcomes beyond the narrow confines of bed nights and legacies. Second, we introduce policies as an entry point to unlock discussions and manifestations of value and futures which connect to AWG. In order to exemplify the workings of the AWG event in these domains, we...... present three central policy stories from the field. The stories tell of how the event was first interested, then activated and finally evaluated. Besides adding a new understanding to policy-driven events as a locus of value creation, we also argue that the AWG 2016 offer speculative bets for new...
In this paper, therefore, a template is developed for corporate network providers in Nigeria for the determination of the precise number of required trunk lines based on the concept of equipment failure and restoration. 1 INTRODUCTION. Telecommunication network is comprised of a variety of common-equipments including ...
Full text: The activity of ZdAJ in 2000 was focused on realisation of the Government-Ordered Project - 6/15 MeV Accelerator. The realisation was accomplished in two stages: - stage I should result in deriving principal operational parameters of the accelerator - stage 2 will result in full implementation of the control system providing optimum control of the equipment and automatic maintaining of its parameters. Within the frames of the first stage, a klystron modulator panel was finished and the design documentation of the mechanical supporting structure, the arm, accelerating structure, collimator and control panel were advanced. Manufacturing of the above sub-units in the workshop has started. In the frames of the Specific Project of the State Committee for Scientific Research, the improvement of Neptun lOPC accelerator was undertaken. The read-out of the monitor dose with atmospheric pressure and ambient temperature compensation has been introduced. New filters for equalising the photon and electron beam and new wedge filters have been designed. Changes in programming have been introduced, which improve the patient's safety by eliminating possible personnel errors and increase the accuracy of radiation fields read-out. In 2000 ZdAJ progressed in development of the Quality System conforming EN-ISO 9001 Standard by including the provisions of EN 46001 Standard. The Standard EN 46001: ''Quality Systems - Medical Equipment''. Detailed requirements related to application of EN ISO 9001 is an European Quality Standard extending the provisions of EN ISO 9001 Standard over the manufacturers of medical equipment. (author)
Bott, T.F.; Thomas, W.S.
The Reactor Vital Equipment Determination Techniques program at the Los Alamos National Laboratory is discussed. The purpose of the program is to provide the Nuclear Regulatory Commission (NRC) with technical support in identifying vital areas at nuclear power plants using a fault-tree technique. A reexamination of some system modeling assumptions is being performed for the Vital Area Analysis Program. A short description of the vital area analysis and supporting research on modeling assumptions is presented. Perceptions of program modifications based on the research are outlined, and the status of high-priority research topics is discussed
Sager, P.; Garin, J.; Hager, E.R.; Spampinato, P.T.; Tobias, D.; Young, N.
A workshop was convened in two sessions in January and March 1981, on the remote maintenance equipment for the Fusion Engineering Device (FED). The objectives of the first session were to familiarize the participants with the status of the design of the FED and to develop a remote maintenance equipment list for the FED. The objective of the second session was to have the participants present design concepts for the equipment which had been identified in the first session. The equipment list was developed for general purpose and special purpose equipment. The general purpose equipment was categorized as manipulators and other, while the special purpose equipment was subdivided according to the reactor subsystem it serviced: electrical, magnetic, and nuclear. Both mobile and fixed base manipulators were identified. Handling machines were identified as the major requirement for special purpose equipment
The fleet of equipment operated by the Virginia Department of Transportation (VDOT) constitutes a large investment, on the order of half a billion dollars. A means of identifying earlier and more accurately those pieces of equipment whose timely repl...
Sager, P.; Garin, J.; Hager, E.R.; Spampinato, P.T.; Tobias, D.; Young, N.
A workshop was convened in two sessions in January and March 1981, on the remote maintenance equipment for the Fusion Engineering Device (FED). The objectives of the first session were to familiarize the participants with the status of the design of the FED and to develop a remote maintenance equipment list for the FED. The objective of the second session was to have the participants present design concepts for the equipment which had been identified in the first session. The equipment list was developed for general purpose and special purpose equipment. The general purpose equipment was categorized as manipulators and other, while the special purpose equipment was subdivided according to the reactor subsystem it serviced: electrical, magnetic, and nuclear. Both mobile and fixed base manipulators were identified. Handling machines were identified as the major requirement for special purpose equipment.
... spray by ship's structure, and consisting of a wash water supply system and— (1) A fixed tank washing... Equipment for Pollution Control § 153.484 Prewash equipment. Unless the ship operator shows that the prewash...
Argyll and Bute District Council, having received a number of planning applications for the erection of wind farms, seeks, in this document, to set out its environmental policy on these installations in line with national government guidelines and those from Strathclyde Regional Council. District Council policy on thirteen environmental issues connected with wind farm construction is set out, covering issues such as environmental impacts on wild-life, noise pollution, access for construction, maintenance and decommissioning vehicles as well as planning consent issues. Recommendations are made to four interested bodies, Strathclyde Regional Council, the Forestry Authority and Scottish Natural Heritage and the Royal Society for the Protection of Birds. (UK)
Geambasu, A.; Segarceanu, D.
The paper presents some considerations concerning the need of comparison between equipment performance proven by test and the service experience in Cernavoda Nuclear Plant. Service performance dana obtain partly from service failures (failures times) and partly from service experience without failure (running times) can be statistically analyzed to obtain predictions of the number of failures of unfailed units in specified period of time, means time to first failure, means time of median failure, a.s.o. These informations can be used during the operation of Nuclear Power Plant to estimate when a equipment should be replaced with a new one in order to prevent getting to the life end point. (author)
Mack, J.E.; Suchomel, R.R.; Angelini, P.
Considerable progress has been made in the development of microsphere handling techniques and equipment for nuclear applications. Work at Oak Ridge National Laboratory with microspherical fuel forms dates back to the early sixties with the development of the sol-gel process. Since that time a number of equipment items and systems specifically related to microsphere handling and characterization have been identified and developed for eventual application in a remote recycle facility. These include positive and negative pressure transfer systems, samplers, weighers, a blender-dispenser, and automated devices for particle size distribution and crushing strength analysis. The current status of these and other components and systems is discussed
In this report, the reliability performance of standby equipment subjected to periodic testing is studied. analytical expressions have been derived for reliability measures, such as the man accumulated operating time to failure, the expected number of tests between two consecutive failures, the mean time to failure following an emergency start-up and the probability of failing to complete an emergency mission of a specified duration. These results are useful for the reliability assessment of standby equipment such as combustion turbine units of the emergency power supply system, and of the Class III power system at a nuclear generating station
Shkurupska Iryna O.
Full Text Available The article identifies needs of the target group, namely structure of motives, which justify making a decision to buy, in order to create efficient marketing strategy of an enterprise, which sell solar-driven equipment in Ukraine. There are five segments in the domestic market of helio-systems: individual consumers, recreation industry, agrarian industry, construction and social spheres. The article allocates 15 motives of acquisition of the solar-driven equipment for these segments, the most important of which are price, availability of solar energy, alternative price and energy saving. Besides, the structure of such motives is determined for each segment individually. In order to choose specific marketing instruments in the policy of promotion of solar-driven equipment, the article identifies differences in the form of goals of use and motives of acquisition between the specified consumer segments. The article reveals certain barriers that interfere with acquisition of solar-driven equipment – low level of trust into helio-systems, conservatism of consumers, absence of free applications for consumers – overcoming which is only possible with the help of certain marketing actions.
Klein, Eric [Neumann Systems Group, Incorporated, Colorado Springs, CO (United States)
During Project DE-FE0007528, CARE (Carbon Absorber Retrofit Equipment), Neumann Systems Group (NSG) designed, installed and tested a 0.5MW NeuStream® carbon dioxide (CO2) capture system using the patented NeuStream® absorber equipment and concentrated (6 molal) piperazine (PZ) as the solvent at Colorado Springs Utilities’ (CSU’s) Martin Drake pulverized coal (PC) power plant. The 36 month project included design, build and test phases. The 0.5MW NeuStream® CO2 capture system was successfully tested on flue gas from both coal and natural gas combustion sources and was shown to meet project objectives. Ninety percent CO2 removal was achieved with greater than 95% CO2product purity. The absorbers tested support a 90% reduction in absorber volume compared to packed towers and with an absorber parasitic power of less than 1% when configured for operation with a 550MW coal plant. The preliminary techno-economic analysis (TEA) performed by the Energy and Environmental Research Center (EERC) predicted an over-the-fence cost of $25.73/tonne of CO2 captured from a sub-critical PC plant.
Abstract: Data center equipment location systems include hardware and software to provide information on the location, monitoring, and security of servers and other equipment in equipment racks. The systems provide a wired alternative to the wireless RFID tag system by using electronic ID tags...
... 46 Shipping 4 2010-10-01 2010-10-01 false Heating equipment. 121.210 Section 121.210 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS CARRYING MORE THAN 150... SYSTEMS AND EQUIPMENT Cooking and Heating § 121.210 Heating equipment. (a) Each heater must be so...
... 46 Shipping 7 2010-10-01 2010-10-01 false Heating equipment. 184.210 Section 184.210 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS (UNDER 100 GROSS TONS) VESSEL CONTROL AND MISCELLANEOUS SYSTEMS AND EQUIPMENT Cooking and Heating § 184.210 Heating equipment...
Several manufacturers are producing automated rig equipment, from complete systems to individual functions for existing drilling rigs. Significant improvements in well site time, costs of operations, and improved drilling performance have led drilling contractors to install this equipment on their rigs. This paper details some of the equipment available for automating rigs
Nitrocellulose film and converter screens used for neutron radiography are described. Difficulties in visualization of radiographs on those films are mentioned. Because there is no equipment for etching nitrocellulose film available on the market Risoe has designed and produced such equipment at an estimated cost of Dkr. 15,000. Design criteria for this equipment are given and its performance described
... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Airplane equipment. 121.605 Section 121.605..., FLAG, AND SUPPLEMENTAL OPERATIONS Dispatching and Flight Release Rules § 121.605 Airplane equipment. No person may dispatch or release an airplane unless it is airworthy and is equipped as prescribed in § 121...
... awarding agency. (d) Management requirements. Procedures for managing equipment (including replacement... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false Equipment. 143.32 Section 143.32...
... proceeds to offset the costs of the replacement equipment subject to the approval of USAID. (f) The... 22 Foreign Relations 1 2010-04-01 2010-04-01 false Equipment. 226.34 Section 226.34 Foreign... ORGANIZATIONS Post-award Requirements Property Standards § 226.34 Equipment. (a) Unless the agreement provides...
... awarding agency. (d) Management requirements. Procedures for managing equipment (including replacement... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no... 32 National Defense 1 2010-07-01 2010-07-01 false Equipment. 33.32 Section 33.32 National Defense...
... awarding agency. (d) Management requirements. Procedures for managing equipment (including replacement... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no... 45 Public Welfare 1 2010-10-01 2010-10-01 false Equipment. 92.32 Section 92.32 Public Welfare...
... EPA. User charges shall be treated as program income. (e) When acquiring replacement equipment, the... offset the costs of the replacement equipment subject to the approval of EPA. (f) The recipient's... 40 Protection of Environment 1 2010-07-01 2010-07-01 false Equipment. 30.34 Section 30.34...
... shall be treated as program income. (e) When acquiring replacement equipment, the recipient may use the... replacement equipment subject to the approval of the Grants Officer after coordination with the DoC operating... 15 Commerce and Foreign Trade 1 2010-01-01 2010-01-01 false Equipment. 14.34 Section 14.34...
... awarding agency. (d) Management requirements. Procedures for managing equipment (including replacement... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no... 40 Protection of Environment 1 2010-07-01 2010-07-01 false Equipment. 31.32 Section 31.32...
... agency. User charges shall be treated as program income. (e) When acquiring replacement equipment, the... offset the costs of the replacement equipment subject to the approval of the Federal awarding agency. (f... 22 Foreign Relations 2 2010-04-01 2010-04-01 true Equipment. 518.34 Section 518.34 Foreign...
... agency. User charges shall be treated as program income. (e) When acquiring replacement equipment, the... offset the costs of the replacement equipment subject to the approval of the Federal awarding agency. (f... 45 Public Welfare 4 2010-10-01 2010-10-01 false Equipment. 2543.34 Section 2543.34 Public Welfare...
... Department. User charges shall be treated as program income. (e) When acquiring replacement equipment, the... offset the costs of the replacement equipment subject to the approval of the Department. (f) The... 22 Foreign Relations 1 2010-04-01 2010-04-01 false Equipment. 145.34 Section 145.34 Foreign...
... awarding agency. (d) Management requirements. Procedures for managing equipment (including replacement... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no... 14 Aeronautics and Space 5 2010-01-01 2010-01-01 false Equipment. 1273.32 Section 1273.32...
... awarding agency. (d) Management requirements. Procedures for managing equipment (including replacement... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no... 29 Labor 4 2010-07-01 2010-07-01 false Equipment. 1470.32 Section 1470.32 Labor Regulations...
... awarding agency. (d) Management requirements. Procedures for managing equipment (including replacement... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no... 15 Commerce and Foreign Trade 1 2010-01-01 2010-01-01 false Equipment. 24.32 Section 24.32...
... charges shall be treated as program income. (e) When acquiring replacement equipment, the recipient may... costs of the replacement equipment subject to the approval of DOE. (f) The recipient's property... 10 Energy 4 2010-01-01 2010-01-01 false Equipment. 600.134 Section 600.134 Energy DEPARTMENT OF...
... the finished product placed therein. New or replacement equipment shall comply with the 3A Sanitary... 7 Agriculture 3 2010-01-01 2010-01-01 false Packaging equipment. 58.626 Section 58.626 Agriculture... Specifications for Dairy Plants Approved for USDA Inspection and Grading Service 1 Equipment and Utensils § 58...
... treated as program income. (d) When acquiring replacement equipment, unless otherwise directed by the REE... the proceeds to offset the costs of the replacement equipment subject to the approval of the REE... 7 Agriculture 6 2010-01-01 2010-01-01 false Equipment. 550.38 Section 550.38 Agriculture...
... awarding agency. (d) Management requirements. Procedures for managing equipment (including replacement... return. (e) Disposition. When original or replacement equipment acquired under a grant or subgrant is no... 38 Pensions, Bonuses, and Veterans' Relief 2 2010-07-01 2010-07-01 false Equipment. 43.32 Section...
... 46 Shipping 7 2010-10-01 2010-10-01 false Cooking equipment. 184.220 Section 184.220 Shipping...) VESSEL CONTROL AND MISCELLANEOUS SYSTEMS AND EQUIPMENT Cooking and Heating § 184.220 Cooking equipment. (a) Doors on a cooking appliance must be provided with hinges and locking devices to prevent...
... 46 Shipping 4 2010-10-01 2010-10-01 false Cooking equipment. 121.220 Section 121.220 Shipping... SYSTEMS AND EQUIPMENT Cooking and Heating § 121.220 Cooking equipment. (a) Doors on a cooking appliance... cooking appliance must be installed to prevent movement in heavy seas. (c) For a grill or similar type of...
... 46 Shipping 7 2010-10-01 2010-10-01 false Diver's equipment. 197.346 Section 197.346 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE OCCUPATIONAL SAFETY AND HEALTH STANDARDS GENERAL PROVISIONS Commercial Diving Operations Equipment § 197.346 Diver's equipment. (a) Each diver...
Shackelford, Linda; Griffith, Bryan
Resistance exercise on ISS has proven effective in maintaining bone mineral density and muscle mass. Exploration missions require exercise with similar high loads using equipment with less mass and volume and greater safety and reliability than resistance exercise equipment used on ISS (iRED, ARED, FWED). Load Bearing Equipment (LBE) uses each exercising person to create and control the load to the partner.
Song, In Gyu; Shin, Seung Han; Kim, Han Suk
Although the number of high-risk neonates has increased in Korea, hospitals were reluctant to open or maintain neonatal intensive care unit (NICU) due to the low medical cost. Consequently, there were regional disparities in facilities, equipment, and neonatal health outcomes. For these reasons, the Korean government began to invest in neonatal care during the last decade. We identified the status of NICUs in Korea and assessed changes after the government-driven policies. We surveyed 87 of 89 hospitals that operated NICUs in 2015. The questionnaire assessed the number of NICU beds, admission and mortality rates of very low birthweight infants (VLBWIs), personnel status, equipment and facilities, and available multidisciplinary approach. Current data was compared with the previous studies and changes in the status and function of the nationwide NICU from 2009 and 2011. During the last 7 years, there was an increase of 462 NICU beds, which met the required number estimated by the number of births and covered about 90% of regional VLBWI births. Status of facilities and equipment improved in all regions in Korea but there were still regional differences in multidisciplinary approach and human resources. The difference in odds ratios for mortality of VLBWI between regions decreased compared to 2009. There was improvement in regional disparities of neonatal care and mortality of premature babies with the government investment in Korea. Further supports are required for human resources and referral system. © 2018 The Korean Academy of Medical Sciences.
Baker, Derek; Hamann, Karen
This report summarises discussions with a small number of meat industry firms about the effects of policy on their innovation activities, and their recommendations for future policy changes. Although firms, like researchers and policymakers, lack strong definitions and measurement procedures...... for innovation, they were able to list and describe their innovation processes and outcomes. Firms expressed some dissatisfaction with innovation policy, and were able to make a number of recommendations for change. Notably, this included its linkage to an overall strategy that emphasises international...
... factorizaton for all exponents. Let V ( x ) be the number of special numbers ≤ x . We will prove that there is a constant c > 1 such that V ( x ) ∼ c x l o g x . We will make some remarks on determining the error term at the end. Using the explicit abc conjecture, we will study the existence of 23 consecutive special integers.
Kritz, M M
Kritz reviews national concepts and policies of migration. She examines how nation-states approach migration and how they define who is a migrant. Policies for permanent, temporary, and illegal migrants are examined for selected countries. While the traditional permanent immigration countries--Australia, Canada, New Zealand, and the US--continue to admit large numbers of permanent migrants, they are also admitting growing numbers of temporary migrants. Other countries, in Europe and the developing world, have different migration histories and use other approaches to admit foreigners--migrants are generally admitted on a temporary basis for work or other purposes. Growing numbers of these temporary migrants, however, do become long-term or permanent settlers, and the distinction between permanent and temporary migration policies becomes a short-term legal one rather than a long-term sociological one. Governments have been seeking those policy instruments that would allow them to improve control over who enters and settles in their territories, and temporary migration policies are the measures to which they are turning. While increasing restriction characterizes the policy stance of most countries toward international migration, this does not necessarily mean that the number of migrants entering is declining. Kritz argues that the concepts employed by countries in their immigration policies frequently do not correspond to the reality, making it necessary to examine the actual context.
Yamauchi, Hirose; Fukunaga, Masao; Nishikawa, Akira; Orimo, Hajime
Many types of bone densitometry equipment are available in Japan, but the numbers of such machines and the numbers of institutions that offer bone densitometry have not been clarified. We analyzed the data from annual surveys conducted by the Japan Osteoporosis Foundation from 1996 to 2006, and we obtained the following results on the use of densitometry equipment: (1) In 1996 there were 6,687 units of bone densitometry equipment in 6,483 institutions in Japan; in 2006 there were 16,371 units in 15,020 institutions. (2) In 2006, of the types of institutions with bone densitometry equipment, the number of clinics was the highest, followed in order by general hospitals, other types of institutions, screening institutions and university hospitals. Rates of increase in the installation of equipment in clinics and other types of institutions were high during the 11-year period from 1996. (3) From 1996 to 2006 the region of interest most frequently used for bone densitometry was the radius. However, during the 11-year period, the proportion of radial densitometry equipment in all institutions with bone densitometry equipment decreased, whereas the proportion of calcaneal densitometry equipment increased. (4) The number of dual-energy X-ray absorptiometry (DXA) units was the highest from 1996 to 2006. However, the proportion of DXA machines in all institutions with bone densitometry equipment decreased over the 11-year period, whereas the proportion of quantitative ultrasound (QUS) machines increased. (5) In 2006, bone densitometry equipment was available in 118 institutions per million Japanese people. Central DXA (spine/hip) equipment was available in 15 per million, radial DXA equipment in 63 per million, and calcaneal QUS equipment in 44 per million. (6) In 2006, among those places with bone densitometry equipment, 46% of university hospitals, 14% of general hospitals, 12% of screening institutions, 5% of clinics, and 6% of other types of institutions possessed more
Turner, A.P.L.; Gorman, J.A.
Improved equipment for removing and replacing control rod drives (CRDs) in BWR plants has been designed, built and tested. Control rod drives must be removed from the reactor periodically for servicing. Removal and replacement of CRDs using equipment originally supplied with the plant has long been recognized as one of the more difficult and highest radiation exposure maintenance operations that must be performed at BWR plants. The improved equipment was used for the first time at Quad Cities, Unit 2, during a Fall 1986 outage. The trial of the equipment was highly successful, and it was shown that the new equipment significantly improves CRD handling operations. The new equipment significantly simplifies the sequence of operations required to lower a CRD from its housing, upend it to a horizontal orientation, and transport it out of the reactor containment. All operations of the new equipment are performed from the undervessel equipment handling platform, thus, eliminating the requirement for a person to work on the lower level of the undervessel gallery which is often highly contaminated. Typically, one less person is required to operate the equipment than were used with the older equipment. The new equipment incorporates a number of redundant and fail safe features that improve operations and reduce the chances for accidents
Pierson, R.K.; Clemons, R.W.
Nuclear station owners have traditionally purchased replacement parts for Class 1E equipment from the original supplier of the equipment. By this method, part and equipment quality could be maintained. In recent years, however, this traditional source of parts has continuously declined as an increasing number of original equipment suppliers stop producing Class 1E equipment or no longer stock parts for older equipment. When replacement parts for Class 1E equipment are not obtainable from the original suppliers, equipment owners have created a variety of methods for assuring the quality of parts obtained from other sources. A standard that provides direction and guidance for maintaining the quality of Class 1E equipment when repaired with parts from alternate sources is, therefore, needed to assure the methods in use are satisfactory and to alert the equipment owners to additional acceptable methods. The standard has now been proposed. IEEE Standard P934 (June, 1983 Draft): ''Requirements for Replacement Parts for Class 1E Equipment in Nuclear Power Generating Stations'' (Ref-3) consist of an introductory section followed by sections on part selection, procurement, replacement (including inspections and tests), non-conforming conditions and records. The proposed standard also includes a non-mandatory appendix on acceptable procurement methods and a summary intended to assist the user in selecting a proper procurement method
Grau, Cai; Defourny, Noémie; Malicki, Julian
BACKGROUND: Documenting the distribution of radiotherapy departments and the availability of radiotherapy equipment in the European countries is an important part of HERO - the ESTRO Health Economics in Radiation Oncology project. HERO has the overall aim to develop a knowledge base...... of the provision of radiotherapy in Europe and build a model for health economic evaluation of radiation treatments at the European level. The aim of the current report is to describe the distribution of radiotherapy equipment in European countries. METHODS: An 84-item questionnaire was sent out to European...... countries, principally through their national societies. The current report includes a detailed analysis of radiotherapy departments and equipment (questionnaire items 26-29), analyzed in relation to the annual number of treatment courses and the socio-economic status of the countries. The analysis is based...
This manual is intended to provide a user with enough detailed instruction to guide them through the Master Equipment List Phase 1 (MEL Phase 1) application system operations. The MEL Phase 1 application is a database system that stores Equipment Identification Number (EIN) information to support equipment tracking in the 200E and 200W Tank Farms for the Tank Waste Remediation System Division. The MEL Phase 1 application supports both the user application and administrative control functions. The user application functions include: viewing by Folder, reporting, performing queries, and editing specific data. The administrative control functions include: maintaining valid user identifications, passwords, privileges, defining drop-down lists, and review of the change log relating to EIN data entries, additions, deletions, and editing. The scope of this User's Manual is to discuss these functions and is intended to guide users and answer questions regarding the MEL Phase 1 application
Research and development works conducted in the Establishment for Nuclear Equipment (ZdAJ) were focused around 3 subject areas: an accelerator for cancer treatment, therapeutical tables, systems and methods for controlling objects that cross international borders. The new, medium energy accelerator for cancer therapy cases is being designed in the Establishment for several years. In 2005 progress was achieved. A physical part, containing an electron beam has been completed and the parameters of that beam make it useful for therapeutical purposes. Consequently, the work on designing and testing of beam control systems, ensuring its high stability, repetition of irradiation parameters and accuracy of dosage have been started. Results of these tests make it very probable that 2006 will be the final year of scientific works and in 2007 the new apparatus will be ready for sales. Therapeutical tables have become a leading product of ZdAJ IPJ. Their technical parameters, reliability and universality in uses are appreciated by many customers of ZdAJ. In 2005, the table Polkam 16 was registered by the national Office for Registration of Medical Equipment as the first product of ZdAJ that meets all technical and formal requirements of the safety mark CE. This allows sales of the product on the market of the European Union. The research and development part of designing a therapeutical table for uses in the total body irradiation technique was also concluded in 2005. After the September 11 terrorist attacks on WTC a matter of controlling international borders have become a priority for many countries. In 2005 in ZdAJ IPJ, we conducted many preliminary calculations and experiments analyzing systems of irradiation sources, both photon and neutron as well as systems of detection and designing of signals triggered by controlling objects crossing the border. The results so far have enabled us to formulate a research project which has been positively evaluated by experts and found
Following discussion at TREF and on the recommendation of the Finance Committee, Council approved a new staff contract policy, which became effective on 1 January 2006. Its application is covered by a new Administrative Circular No. 2 (Rev. 3) 'Recruitment, appointment and possible developments regarding the contractual position of staff members'. The revised circular replaces the previous Circulars No. 9 (Rev. 3) 'Staff contracts' and No. 2 (Rev. 2) 'Guidelines and procedures concerning recruitment and probation period for staff members'. The main features of the new contract policy are as follows: The new policy provides chances for long-term employment for all staff recruits staying for four years without distinguishing between those assigned to long-term or short-term activities when joining CERN. In addition, it presents a number of simplifications for the award of ICs. There are henceforth only 2 types of contract: Limited Duration (LD) contracts for all recruitment and Indefinite Contracts (IC) for...
Bertel, E.; Fraser, P.
External costs of energy have been assessed in a number of authoritative and reliable studies based upon widely accepted methodologies such as life cycle analysis (LCA). However, although those costs are recognised by most stakeholders and decision makers, results from analytical work on externalities and LCA studies are seldom used in policy making. The International Energy Agency (IEA) and the Nuclear Energy Agency (NEA) convened a joint workshop in November 2001 to offer experts and policy makers an opportunity to present state-of-the-art results from analytical work on externalities and debate issues related to the relevance of external costs and LCA for policy-making purposes. The findings from the workshop highlight the need for further work in the field and the potential rote of international organisations like the IEA and the NEA in this context. (authors)
The history of the FASER Rescue Equipment and Mining Lamp Factory founded in 1924 is discussed. Plant development from 1924 to 1939 and from 1947 to 1984 is evaluated. The FASER Plant has been subordinated to the EMAG Center for Research and Production of Electrical Engineering and Mine Automation since 1980. Equipment manufactured by the plant is discussed: oxygen respirators, canisters, protective clothing, control systems and measuring instruments used in mine rescue, medical equipment, lighting systems and light bulbs for underground mines. Some problems associated with manufacturing processes are evaluated: manufacturing equipment, manufacturing technologies, quality of rescue equipment, innovation and its economic significance, etc.
Classic study discusses number sequence and language and explores written numerals and computations in many cultures. "The historian of mathematics will find much to interest him here both in the contents and viewpoint, while the casual reader is likely to be intrigued by the author's superior narrative ability.
Full Text Available Background: A growing number of cancer cases enhances the usage of cytostatic agents and thereby contributes to the increase in the number of health care workers occupationally exposed to cytostatics. Material and Methods: This article presents the results of the survey aimed at obtaining data on the reduction of occupational exposure through using personal protective equipment by the medical and pharmaceutical personnel involved in handling cytostatics. The questionnaires were sent by mail or e-mail to oncology hospitals and pharmacies preparing cytostatic drugs. Responses were received from 94 people employed in these workplaces. The main questions concerned the forms of cytostatics; job activities; types of personal protective equipment used and working time under exposure to cytotoxic drugs. Results: The majority (over 90% of the healthcare personnel declared the use of personal protective equipment when working under conditions of exposure to cytostatic drugs. Depending on the type of protection, 15–35% of people reported that the most frequent time of their single use of the apron, the overalls, the gloves, the cap, the goggles or the respirators did not exceed few minutes. Gloves were changed most frequently. However, half of the responses indicated that the time after which the respondents removed protection equipment greatly differed. Conclusions: Almost the whole group of respondents applied personal protective equipment when working under exposure to cytostatics. However, personal protective equipment was not used every time in case of exposure. The medical and pharmaceutical staff worked under exposure to cytostatics for a few or even dozen hours during the working day. Med Pr 2016;67(4:499–508
Analysis of in-plant fuel operating experience shows that assembly damage has a variety of causes: Handling incidents; external hazards during operation; wear and perforation; fuel manufacturing defects and other causes. Depending on the seriousness of the damage and the burnup level reached by assemblies, several repair possibilities arise: If they are leaktight and if grid distortion is minimal and does not jeopardize rod restraint, they are reloaded, subject to local servicing for restoring acceptable grid geometry. In all other cases, the assemblies have to be restored either by replacing the damaged skeleton or be replacing the leaking rod(s). This paper presents methods, equipments and the FRAGEMA experience in assemblies repair. (author). 5 pictures, 3 diagrams
Warasina, N.; Minakawa, K.; Tanizaki, Y.
Oil used in refrigeration equipment (OFE) contains polyether type synthetic oil with 0.1-3 percent of aromatic antioxidant as an additive; the antioxidant has 1-2 atoms of N or 1 atom N and 1 atom S in the molecule, and 0.1-5% organic Sn compounds. It is preferable to use phenyl-alpha-naphtylamin as the additive, and for the Sn, dibutylcarboxilate Sn or dibutyldilaurinate Sn. It is recommended that a synthetic oil with the following formula: X(O(AO)mY)n, where X=H or the rest of alcohol; A- alkylene C/sub 2/-C/sub 4/; Y=H, alkyl, alkenyl, acyl, benzyl or arile; m=2-100; n=1-6. This OFE has a high chemical stability when in contact with freon or metals at high temperatures for long time periods, and has good lubricating features.
Copeland, R. J.
This paper describes the preliminary design of a Shuttle Spacelab Core Equipment Freezer. The unit will provide the capability to freeze and store many experiment specimens. Two models of the unit are planned. One model provides storage at -70 C; the other model will provide -70 C storage, a freeze dry capability, storage at a selectable temperature in the range of 0 C to -70 C, and means of maintaining close temperature tolerances. In addition an exchanger loop will be available at 4 C for cooling of a centrifuge and a remote storage compartment. A test tube holder, a dish holder and thermal capacitors for rapid freezing of large specimens will also be provided. A Stirling Cycle was selected as the active refrigerator for minimum cost and weight.
The Purex process is the solvent extraction system that uses tributyl phosphate as the extractant for separating uranium and plutonium from irradiated reactor fuels. Since the first flowsheet was proposed at Oak Ridge National Laboratory in 1950, the process has endured for over 30 years with only minor modifications. The spread of the technology was rapid, and worldwide use or research on Purex-type processes was reported by the time of the 1955 Geneva Conference. The overall performance of the process has been so good that there are no serious contenders for replacing it soon. This paper presents: process description; equipment performance (mixer-settlers, pulse columns, rapid contactors); fission product decontamination; solvent effects (solvent degradation products); and partitioning of uranium and plutonium
Mussio, L.; Castiglioni, J.; Diano, W.
A low cost automation of some instruments by means of simple electronic circuits and a microcomputer Apple IIe. type is discussed. The electronic circuits described are: a) a position detector including phototransistors connected as differential amplifier; b) a current source that, using the error signal of the position detector, changes the current through the coil of an electromagnetic balance to restore its zero position; c) a proportional temperature controller, zero volt switching to drive a furnace to a desired temperature; d) an interface temperature regulator-microcomputer to control the temperature regulator by software; e) a multiplexer for an analog input of a commercial interface. Those circuits are applied in a thermogravimetric equipment used also for vapours adsorption. A program in block diagram form is included and is able to record change of mass, time, furnace temperature and to drive the temperature regulator in order to have the heating rates or the temperature plateaux needed for the experiment. (author) [pt
Full text: The main objective of the activity of the Establishment for Nuclear Equipment (ZdAJ) in 1999 was to obtain the ISO 9001 certificate. Work on this problem has been successfully completed. The changes introduced in agreement with requirements of ISO in supervising the construction, manufacturing and servicing eliminate possible deficiencies of our products and will pay in the future. Two new important ventures have been undertaken: design of an accelerator with two photon energies and a reconstruction of simulator directed towards better geometrical parameters. The completion of the improvements in accelerator is foreseen for the year 2002. The changes comprise almost all sub-assemblies of the device. The modernized simulator will be installed in the hospital already in the year 2000 - the ameliorations concern mainly the arm of the apparatus, collimator, driving gears and control system. Of course - apart from this, the routine production activity of the Establishment was continued in 1999. (author)
When developing new solvent extraction processes, one often has to evaluate new solvents, new aqueous phases, or both for their ability to work in plant-scale equipment. To facilitate solvent characterization, a simple test is proposed based on the dimensionless dispersion number (N Di ). It allows one to characterize the ability of the solvent to separate from a two-phase dispersion and allows one to estimate process throughput for equipment of a given size. Several ways to carry out the N Di test are given, including a standard test procedure. The N Di test was applied to the performance of solvent extraction equipment with discrete process stages, the leaching of plasticizers from plastic tubing, and the development of a new solvent for the combined extraction of strontium and transuranic elements
A data center equipment location system includes both hardware and software to provide for location, monitoring, security and identification of servers and other equipment in equipment racks. The system provides a wired alternative to the wireless RFID tag system by using electronic ID tags conne...... to an individual electronic ID tag to activate a sensory indicator to enable a technician(s) to locate a piece of equipment that is in need of repair or replacement.......A data center equipment location system includes both hardware and software to provide for location, monitoring, security and identification of servers and other equipment in equipment racks. The system provides a wired alternative to the wireless RFID tag system by using electronic ID tags...... connected to each piece of equipment, each electronic ID tag connected directly by wires to a equipment rack controller on the equipment rack. The equipment rack controllers then link over a local area network to a central control computer. The central control computer provides an operator interface...
Ideally, the original supplier of a piece of nuclear safety-related equipment has performed a qualification program and will continue to support that equipment throughout the lifetime of the nuclear power plants in which in equipment is installed. The supplier's nuclear quality assurance program will be maintained and he will continue to offer all necessary replacement parts. These parts will be identical to the original parts, certified to the original purchase order requirements, and the parts will be offered at competitive prices. Due to the changing nature of the nuclear plant equipment market, however, one or more of those ideal features are frequently unavailable when safety-related replacement equipment or parts are required. Thus, the process of equipment and parts qualification has had to adjust in order to ensure obtaining qualified replacements when needed. This paper presents some new directions taken in the qualification of replacement equipment and parts to meet changes in the marketplace
Diem, Sarah; Young, Michelle D.; Welton, Anjalé D.; Mansfield, Katherine Cumings; Lee, Pei-Ling
What counts as critical policy analysis in education? Over the past 30 years, a tightening of national educational policies can be seen in the USA and across the globe. Over this same period of time, a growing number of educational policy scholars, dissatisfied with traditional frameworks, have used critical frameworks in their analyses. Their…
Holleman, John J.
A study was conducted at Vista College to compare the sabbatical leave policy of the Peralta Community College District with those of other districts and to develop alternative policies that would permit a greater number of faculty to obtain sabbatical leaves. Policy statements were received from nine of the twelve districts surveyed, and…
Hansen, Rene Rydhof; Nielson, Flemming; Nielson, Hanne Riis
Policy conformance is a security property gaining importance due to commercial interest like Digital Rights Management. It is well known that static analysis can be used to validate a number of more classical security policies, such as discretionary and mandatory access control policies, as well...
This policy reader comprises: Correspondence; Memorandum of Understanding between the US Department of Transportation and the US Department of Energy for the Transportation of Radioactive Materials under the Nuclear Waste Policy Act; Internal Guidelines for Interactions with Communities and Local Governments; Statement by Ben C. Rusche before the Committee on Interior and Insular Affairs, Subcommittee on Energy and the Environment, US House of Representatives, September 13, 1985; Speech presented by Ben C. Rusche before the ANS/CNS/AESJ/ENS Topical Meeting, Pasco, Washington, September 24, 1985 - ''Status of the United States' High-Level Nuclear Waste Disposal Program''; and ''DOE Seeks Comments on Nuclear Transportation Planning,'' DOE News, September 30, 1985
Participants in the Seminar on Population Policies for Top-level Policy Makers and Program Managers, meeting in Thailand during January 1987, examined the challenges now facing them regarding the implementation of fertility regulation programs in their respective countries -- Bangladesh, China, India, Indonesia, Malaysia, Nepal, Pakistan, the Philippines, the Republic of Korea, and Thailand. This Seminar was organized to coincide with the completion of an Economic and Social Commission for Asia and the Pacific (ESCAP) study investigating the impact and efficiency of family planning programs in the region. Country studies were reviewed at the Seminar along with policy issues about the status of women, incentive and disincentive programs, and socioeconomic factors affecting fertility. In Bangladesh the government recognizes population growth as its top priority problem related to the socioeconomic development of the country and is working to promote a reorientation strategy from the previous clinic-oriented to a multidimensional family welfare program. China's family planning program seeks to postpone marraige, space the births of children between 3-5 years, and promote the 1-child family. Its goal is to reduce the rate of natural increase from 12/1000 in 1978 to 5/1000 by 1985 and 0 by 2000. India's 7th Five-Year-Plan (1986-90) calls for establishing a 2-child family norm by 2000. In Indonesia the government's population policy includes reducing the rate of population growth, achieving a redistribution of the population, adjusting economic factors, and creating prosperous families. The government of Indonesia reversed its policy to reduce the population growth rate in 1984 and announced its goal of achieving a population of 70 million by 2100 in order to support mass consumption industries. It has created an income tax deduction system favoring large families and maternity benefits for women who have up to 5 children as incentives. Nepal's official policy is to
Lauridsen, Karen M.
Like any other text, instructive texts function within a given cultural and situational setting and may only be available in one language. However, the end users may not be familiar with that language and therefore unable to read and understand the instructions. This article therefore argues...... that instructive texts should always be available in a language that is understood by the end users, and that a corporate communication policy which includes a language policy should ensure that this is in fact the case for all instructive texts....
... Sanitary Standards and accepted practices currently in effect for such equipment. (c) New or replacement equipment or machinery (including any replacement parts) brought onto the premises of any official plant... equipment and machinery, and any replacement parts for such equipment and machinery. Totally enclosed...
In terms of purchasing power, India represents the fourth largest economy in the world. In the year April 1, 2001-Mar 31, 2002, it was estimated that India had a 5.4 per cent growth in gross domestic product (GDP). Canada experienced a 19.9 per cent increase in exports to India in 2001, reaching 656 million dollars. With the world's six-largest energy consumption, oil demand in India is expected to grow to 179 million tonnes in 2006-2007, while the demand for natural gas is expected to reach 231 million cubic metres per day in the same period. To meet this growing demand, India will require investments in the order of 150 billion dollars over the next 10 to 12 years. The oil and gas industry is being opened to the private sector and foreign direct investment, due to new government policies on exploration, production, distribution, and sales. Foreign involvement in exploration, previously restricted to Indian state-owned firms, is now allowed through the New Exploration Licensing Policy. In exploration and production (E and P) activities, as well as the refinery sector, foreign ownership of up to 100 per cent is now allowed. Two Indian companies which dominate the Indian E and P sector, namely Oil and Natural Gas Corporation (ONGC) and Oil India Limited (OIL), will be upgrading their ageing infrastructure, purchasing new equipment and redeveloping existing oil and gas fields, thereby creating opportunities for the supply of equipment and services. Canadian companies possessing the latest technologies and services in exploration, drilling machinery and equipment, directional drilling services, production machinery and equipment, enhanced recovery services, deep-water drilling equipment and services, and equipment for coal methane E and P should benefit from these opportunities. Over 12,000 kilometres of pipelines are being planned across India, as well as private opportunities in the refinery sector which was opened to the private sector in April 2002. Occasional
Koninck, Jean-Marie De
Who would have thought that listing the positive integers along with their most remarkable properties could end up being such an engaging and stimulating adventure? The author uses this approach to explore elementary and advanced topics in classical number theory. A large variety of numbers are contemplated: Fermat numbers, Mersenne primes, powerful numbers, sublime numbers, Wieferich primes, insolite numbers, Sastry numbers, voracious numbers, to name only a few. The author also presents short proofs of miscellaneous results and constantly challenges the reader with a variety of old and new n
Nearly 100 projects are being assisted by Agency experts and equipment in 38 countries under the 1965 programme to be financed from Agency funds, which the Board of Governors approved at its meeting in February, together with four other countries where projects previously approved extend into 1965. In addition, further work is being financed under the UN Expanded Programme of Technical Assistance, including several important regional projects. Under the Agency's long-term programme, it is desirable that all types of technical assistance, whether training, research, or expert advice, should be combined as far as possible. Each country will therefore be asked, in respect of its 1966 programme, to make its requests for experts, equipment, fellowships, scientific visits and research grants as a single submission. The Agency then prepares a country programme of technical assistance, in collaboration with the Government. The number of requests for experts and equipment continues to grow year by year, and it has not been possible to finance them all. This increase is largely because a number of Member States have now set up research reactors and established a nucleus of laboratories under bilateral arrangements; they then turn to the Agency for assistance in developing their programmes. The estimated cost of experts and equipment being provided from Agency resources is $874 000 in 1965, of which $596 800 is for experts, and $277 200 is for equipment and supplies. The Agency also assists some Member States in making arrangements to receive technical assistance directly from other Member States. The work covers a wide range, with isotopes predominating; about 30 projects deal with production of isotopes, their applications in medicine, agriculture and hydrology, in food preservation and industry. A number of projects are concerned with various aspects of reactor construction and use; others deal with health and safety, instrumentation, special branches of chemistry and
McConnell, C R
Although any decision to purchase a piece of capital equipment involves a number of the organization's functions, the department manager has some significant responsibilities in the selection and acquisition of capital equipment. Except for unavoidable replacement of essential equipment that fails unexpectedly, capital purchases must ordinarily be planned in advance through the annual budgeting process. The department manager is ordinarily the organization's primary source of information in major capital expenditure projects; therefore, it is essential that the manager follow a logical process for identifying and evaluating alternative equipment choices and perform a consistent economic analysis of the alternatives.
Reinfuss, Marian; Byrski, Edward; Malicki, Julian
Background and purpose To evaluate the current status of radiotherapy facilities, staffing, and equipment, treatment and patients in Poland for the years 2005–2011 following implementation of the National Cancer Programme. Methods A survey was sent to the radiotherapy centres in Poland to collect data on available equipment, staffing, and treatments in the years 2005–2011. Results In 2011, 76,000 patients were treated with radiotherapy at 32 centres vs. 63,000 patients at 23 centres in 2005. Number of patients increased by 21%. In 2011, there were 453 radiation oncologists – specialists (1 in 168 patients), 325 medical physicists (1 in 215 patients), and 883 radiotherapy technicians (1 in 86 patients) vs. 320, 188, and 652, respectively, in 2005. The number of linear accelerators increased by 60%, from 70 units in 2005 to 112 in 2011. The current linac/patient ratio in Poland is 1 linac per 678 patients. Waiting times from diagnosis to the start of treatment has decreased. Conclusion Compared to 2005, there are more treatment facilities, more and better equipment (linacs), and more cancer care specialists. There are still large differences between the 16 Polish provinces in terms of equipment availability and ease of access to treatment. However, radiotherapy services in Poland have improved dramatically since the year 2005. PMID:24416548
It is widely accepted that individual radiotherapy centres should have in place a comprehensive quality assurance programme on all the necessary steps for the delivery of safe accurate treatment. As regards the performance of radiotherapy equipment and dosimetry, the most widely used process of external checking has been dosimetry intercomparison, comparing independently measured doses to locally stated doses in a variety of conditions. These have been at a number of different levels: from basic beam calibration; up to and including exercises employing anatomic or pseudo-anatomic phantoms and incorporating tests of treatment planning equipment and procedures. Some of these have been one-off exercises, whilst others are continuing, or have given rise to on-going quality audit programmes on a national (or wider) basis. A number of these have evolved, or are evolving, into audits which include external checking of the achievement of standards in performance of treatment equipment, as well as in the dosimetry in each institution involved. The principles and methodologies of the various types of external checking programmes for treatment equipment and dosimetry are reviewed, covering the experimental approaches and the tolerances applied. What is included in a given programme will, of necessity, depend on the resources available and the purpose of the exercise. Methods and tolerances must be matched to endpoint. Tolerance levels must take into account the experimental uncertainties of the measurement methods employed. Finally, external audit can only be used to complement, and in conjunction with, institutional quality assurance programmes and not as a substitute for them
making in European style federations in relation with the Anglo-Saxon ones. b) that the policy-process in the EU resembles that of the European style federations, and c) the Constitutional Treaty (CT) or a possible CT-light would strengthen the federal policy-making characteristics already present......By using the policy cycle approach, this paper compares the policy-process in a number of Anglo-Saxon type federations with the policy-process in continental-European style federations from within the European Union (EU) area. The comparison would reveal: a) distinct different styles of policy...
This serial report contains translations from the world press and radio relating to worldwide political, economic and technical developments in telecommunications, computers, and satellite communications...
This serial report contains translations from the world press and radio relating to worldwide political, economic and technical developments in telecommunications, computers, and satellite communications...
Garbarino, James; Governale, Amy; Henry, Patrick; Nesi, Danielle
Hardly a week goes by in the United States (and to varying degrees, in the rest of the world) that the word "terrorism" does not appear in the collective consciousness, as represented, channeled, and shaped by the mass media in its many print, broadcast, and internet manifestations. While relatively few children worldwide (and even fewer…
Computer Plant in Minas ( JORNAL DO BRASIL , 2 Aug 78) 40 PERU Briefs Communications System Enlarged 41 SUB-SAHARAN AFRICA INTER-AFRICAN...SUPPORTS ESTABLISHMENT OF COMPUTER PLANT IN MINAS Rio de Janeiro JORNAL DO BRASIL in Portuguese 2 Aug 78 p 19 [Text] Belo Horizonte--CAPFE
Inaugurates System Combining Three Stations ( JORNAL DO BRASIL , 13 May 78) kO Ericsson To Provide Technology for CPA Installation (O ESTADO DE...CSO: 5500 39 BRAZIL RADIOBRAS INAUGURATES SYSTEM COMBINING THREE STATIONS Rio de Janeiro JORNAL DO BRASIL in Portuguese 13 May 78 p 15 [Text
... UNITED STATES Economic Impact Policy This notice is to inform the public that the Export-Import Bank of... export of approximately $450 million worth of mining equipment and services to Mexico. The U.S. exports... in the U.S., Canada, Mexico, and Brazil. Interested parties may submit comments on this transaction...
... UNITED STATES Economic Impact Policy This notice is to inform the public that the Export-Import Bank of... million revolving credit line for the export of U.S. foundry tooling equipment to Mexico. The U.S. exports... economic[email protected] or by mail to 811 Vermont Avenue, NW., Room 1238, Washington, DC 20571, within 14...
The Division Directors at Lawrence Berkeley Laboratory are responsible for implementing a maintenance program for research equipment (also referred to as programmatic equipment) assigned to them. The program must allow maintenance to be accomplished in a manner that promotes operational safety, environmental protection and compliance, and cost effectiveness; that preserves the intended functions of the facilities and equipment; and that supports the programmatic mission of the Laboratory. Programmatic equipment -- such as accelerators, lasers, radiation detection equipment, and glove boxes -- is dedicated specifically to research. Installed equipment, by contrast, includes the mechanical and electrical systems installed as part of basic building construction, equipment essential to the normal functioning of the facility and its intended use. Examples of installed equipment are heating, ventilating, and air conditioning systems; elevators; and communications systems. The LBL Operating and Assurance Program Plan (PUB-3111, Revision 4) requires that a maintenance program be prepared for programmatic equipment and defines the basic maintenance program elements. Such a program of regular, documented maintenance is vital to the safety and quality of research activities. As a part of that support, this document offers guidance to Laboratory organizations for developing their maintenance programs. It clarifies the maintenance requirements of the Operating and Assurance Program (OAP) and presents an approach that, while not the only possibility, can be expected to produce an effective maintenance program for research equipment belonging to the Laboratory's organizations
"This article presents the basic characteristics of the foreign workers recruiting policy in Japan, which consists [of] barring entry to unskilled workers, and confronts it with the actual tolerance for a large number of illegal unskilled workers. After a historical overview of the reasons for the current policy, the article examines elements which reveal that a seclusionist policy is based on mistaken assumptions and reviews policy options to deal with the issue of illegal migration." excerpt
Pedersen, Rasmus Tue
Numbers permeate modern political communication. While current scholarship on framing effects has focused on the persuasive effects of words and arguments, this article shows that framing of numbers can also substantially affect policy preferences. Such effects are caused by ratio bias, which...
This document may be of assistance in applying the New Source Review (NSR) air permitting regulations including the Prevention of Significant Deterioration (PSD) requirements. This document is part of the NSR Policy and Guidance Database. Some documents in the database are a scanned or retyped version of a paper photocopy of the original. Although we have taken considerable effort to quality assure the documents, some may contain typographical errors. Contact the office that issued the document if you need a copy of the original.
Vazzana, Anthony; Garth, David
One of the oldest branches of mathematics, number theory is a vast field devoted to studying the properties of whole numbers. Offering a flexible format for a one- or two-semester course, Introduction to Number Theory uses worked examples, numerous exercises, and two popular software packages to describe a diverse array of number theory topics.
Prime numbers are often described as the "building blocks" of natural numbers. This article shows how the author and his students took this idea literally by using prime factorizations to build numbers with blocks. In this activity, students explore many concepts of number theory, including the relationship between greatest common factors and…
... described in this paragraph (c)(2) and make them available to the engine manufacturer for any auditing under... assurance from equipment manufacturers or your authorized distributors that they need a certain number of...
Adaptation Finance: Linking Research, Policy, and Business. This project will train up to 36 emerging climate change leaders in the field of adaptation finance, which funds efforts to adapt to climate change impacts. The goal is to bring together participants from research, policy, and private sector backgrounds to equip them ...
Cohen, Robert B.; Donow, Kenneth
New policies are needed for the U.S. telecommunications industry. The continuation of current policies--which emphasize customer and convenience services to the near exclusion of developing domestically produced equipment and improving infrastructure--will constrain the domestic growth of U.S. corporations and make it difficult for smaller…
Adaptation Finance: Linking Research, Policy, and Business. This project will train up to 36 emerging climate change leaders in the field of adaptation finance, which funds efforts to adapt to climate change impacts. The goal is to bring together participants from research, policy, and private sector backgrounds to equip them ...
The knowledge of how the environment and load of organic material in general and especially polymers and lubricants, is affecting the degradation of important properties, have increased during the last decade. However the restrictions using established additives like some color pigments due to their poisonousness e.g. pigments based at cadmium, lead, mercury etc. have caused problems when replacing additives to polymers. The replacement additives have often been used in new design without going through the required material qualification procedure. There have also been observed that some non-qualified and non-approved materials have been installed in some power plants due to false documentation. There are also a lot of new manufacturers, of materials similar to the previously qualified materials, active at the market. This increases the difficulty to ensure that the required material quality is used. New materials, new additives and new manufacturers makes if more and more difficult to assure that the expected material is present. This causes more strict demands of how the new materials often used in equipment at type-testing and in replacement materials are analyzed and documented. By implementing new steps for chemical, mechanical and electrical analysis and increase the general quality assurance content this issue can be managed. (authors)
Reschovsky, James; Cassil, Alwyn; Pham, Hoangmai H
This Data Bulletin presents findings from the Center for Studying Health System Change (HSC) 2008 Health Tracking Physician Survey, a nationally representative mail survey of U.S. physicians providing at least 20 hours per week of direct patient care. The sample of physicians was drawn from the American Medical Association master file and included active, nonfederal, office- and hospital-based physicians. Residents and fellows were excluded, as well as radiologists, anesthesiologists and pathologists. The survey includes responses from more than 4,700 physicians, and the response rate was 62 percent. Since this Data Bulletin examines the extent of physician practice ownership or leasing of medical equipment, the sample was limited to 2,750 physicians practicing in community-based, physician-owned practices, who represent 58 percent of all physicians surveyed. Physicians employed by hospitals, who practiced in hospital-based settings or who worked in hospital-owned practices were excluded.
Biest, O. v.d.
The research activities of the Division at the Petten Establishment have the aims of characterising the properties of high temperature materials in industrial process environments and of understanding the structures involved in order to gain an insight into behavioural mechanisms. Metallic materials fall within the scope of the programme; the activities are, at present, almost entirely concerned with austenitic steels and nickel based alloys. Starting in 1984, advanced ceramic materials will be studied as well. The equipment available permits the study of mechanical properties in controlled gaseous environments, of the rates and mechanisms of corrosive reactions between materials and those environments, and of the surface and bulk structures by advanced physical techniques. Special preparation and treatment techniques are available. The Division has developed a Data Bank on high temperature alloys. It also operates an information Centre, the activities of which include the organisation of scientific meetings, the commissioning of ''state of the art'' studies on topics in the field of high temperature materials and their applications and the development of a inventory of current research activities in the field in Europe. This booklet is intended to present the facilities and services of the Division to the organizations which are interested in its programmes of work
The objective and scope of this document are to list and briefly describe the major control and communication equipment necessary for waste package emplacement at the proposed nuclear waste repository at Yucca Mountain. Primary performance characteristics and some specialized design features of the required equipment are explained and summarized in the individual subsections of this document. This task was evaluated in accordance with QAP-2-0 and found not to be quality affecting. Therefore, this document was prepared in accordance with NAP-MG-012. The following control and communication equipment are addressed in this document: (1) Programmable Logic Controllers (PLC's); (2) Leaky Feeder Radio Frequency Communication Equipment; (3) Slotted Microwave guide Communication Equipment; (4) Vision Systems; (5) Radio Control Equipment; and (6) Enclosure Cooling Systems
Ciocoiu, Carmen Nadia; Colesca, Sofia Elena; Rudăreanu, Costin; Popescu, Maria-Loredana
Around the world there are growing concerns for waste electrical and electronic equipment. This is motivated by the harmful effects of waste electrical and electronic equipment on the environment, but also by the perspectives of materials recovery. Differences between countries regarding waste electrical and electronic equipment management are notable in the European Union. Romania is among the countries that have made significant efforts to comply with European Union regulations, but failed reaching the collection target. The article presents a mini review of the waste electrical and electronic equipment management system in Romania, based on legislation and policy documents, statistical data, research studies and reports published by national and international organisations. The article debates subjects like legislative framework, the electrical and electronic equipment Romanian market, the waste electrical and electronic equipment collection system, waste electrical and electronic equipment processing and waste electrical and electronic equipment behaviour. The recast of the European directive brings new challenges to national authorities and to other stakeholders involved in the waste electrical and electronic equipment management. Considering the fact that Romania has managed a collection rate of roughly 1 kg capita(-1) in the last years, the new higher collection targets established by the waste electrical and electronic equipment Directive offer a serious challenge for the management system. Therefore, another aim of the article is to highlight the positive and negative aspects in the Romanian waste electrical and electronic equipment field, in order to identify the flows that should be corrected and the opportunities that could help improve this system to the point of meeting the European standards imposed by the European Directive. © The Author(s) 2015.
Bourassa, Dominic; Gauthier, François; Abdul-Nour, Georges
Accidental events in manufacturing industries can be caused by many factors, including work methods, lack of training, equipment design, maintenance and reliability. This study is aimed at determining the contribution of failures of commonly used industrial equipment, such as machines, tools and material handling equipment, to the chain of causality of industrial accidents and incidents. Based on a case study which aimed at the analysis of an existing pulp and paper company's accident database, this paper examines the number, type and gravity of the failures involved in these events and their causes. Results from this study show that equipment failures had a major effect on the number and severity of accidents accounted for in the database: 272 out of 773 accidental events were related to equipment failure, where 13 of them had direct human consequences. Failures that contributed directly or indirectly to these events are analyzed.
...)) as required by the National Environmental Policy Act (42 U.S.C. 4321 et seq.), other environmental..., Notice No. 3] RIN 2130-ZA04 Adjustment of Monetary Threshold for Reporting Rail Equipment Accidents.... Notice and Comment Procedures and Effective Date In this rule, FRA has recalculated the monetary...
... Procedures) (64 FR 28545 (May 26, 1999)) as required by the National Environmental Policy Act (42 U.S.C. 4321..., Notice No. 5] RIN 2130-ZA10 Adjustment of Monetary Threshold for Reporting Rail Equipment Accidents... monetary reporting threshold based on the formula discussed in detail and adopted, after notice and comment...
... required by the National Environmental Policy Act (42 U.S.C. 4321 et seq.), other environmental statutes..., Notice No. 6] RIN 2130-ZA12 Adjustment of Monetary Threshold for Reporting Rail Equipment Accidents..., or be subject to notice and comment. In 1996 FRA adopted a new method for calculating the monetary...
... equipment in the mobile radio service. 90.185 Section 90.185 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) SAFETY AND SPECIAL RADIO SERVICES PRIVATE LAND MOBILE RADIO SERVICES Policies... mobile radio service. Two or more persons eligible for licensing under this rule part may be licensed for...
Fink, C. Dennis; Hibbits, Francis L.
The study examines post office mail processing equipment (MPE) maintenance positions on the basis of interviews conducted among maintenance mechanics and supervisors at 17 small, medium, and large mechanized post offices for the purpose of determining existing and desired maintenance practices and maintenance personnel policy. The study considers…
RTO-MP-SAS-080 17 - 1 The Implementation of an MCDM Tool for the Acquisition of Military Equipment Frédéric Hallot, Philippe De Beir, Hugo...our experience as well in teaching as in consultancy at the Royal Military Academy we learned that previously existing MCDM software did not fit well...AND SUBTITLE The Implementation of an MCDM Tool for the Acquisition of Military Equipment 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM
Zhang, X.; Han, K.; Duan, T.; Liu, Z.; Lu, H. [China University of Mining and Technology, Xuzhou (China)
Based on client/server and browser/server models, the management information system described realized the entire life-cycle management of mine railway equipment which included universal equipment and special equipment in the locomotive depot, track maintenance division, electrical depot and car depot. The system has other online functions such as transmitting reports, graphics management, statistics, searches, graphics wizard and web propaganda. It was applied in Pingdingshan Coal Co. Ltd.'s Railway Transport Department. 5 refs., 4 figs.
Fan, Wei (David); Gemar, Mason D.; Machemehl, Randy
The primary function of equipment managers is to replace the right equipment at the right time and at the lowest overall cost. In this paper, the opportunities and challenges associated with equipment replacement optimization (ERO) are discussed in detail. First, a comprehensive review of the state-of-the art and state-of-the practice literature for the ERO problem is conducted. Second, a dynamic programming (DP) based optimization solution methodology is presented to solve the ERO problem. T...
The practices (veterinary anatomy laboratory, veterinarian physiology laboratory I, veterinarian physiology laboratory II, and veterinarian physiology chemistry laboratory) in the area of basic veterinary medicine are important subjects for acquiring knowledge and the technique by the process of shifting from the liberal arts subject to a specialized subjects for the area of applied veterinary medicine and clinical veterinary medicine. The number of equipment is insufficient to practice effec...
ort DEFENSE COMMISSARY AGENCY FINANCIAL REPORTING OF PROPERTY, PLANT, AND EQUIPMENT Report Number 98-097 March 27, 1998 Office of the Inspector...UNDER SECRETARY OF DEFENSE (COMPTROLLER) DIRECTOR, DEFENSE COMMISSARY AGENCY SUBJECT: Audit Report on Defense Commissary Agency Financial Reporting of...General for Auditing Office of the Inspector General, DoD Report No. 98-097 March 27, 1998 (Project No. 7FJ-2026) Defense Commissary Agency Financial
The technical difficulties of algebraic number theory often make this subject appear difficult to beginners. This undergraduate textbook provides a welcome solution to these problems as it provides an approachable and thorough introduction to the topic. Algebraic Number Theory takes the reader from unique factorisation in the integers through to the modern-day number field sieve. The first few chapters consider the importance of arithmetic in fields larger than the rational numbers. Whilst some results generalise well, the unique factorisation of the integers in these more general number fields often fail. Algebraic number theory aims to overcome this problem. Most examples are taken from quadratic fields, for which calculations are easy to perform. The middle section considers more general theory and results for number fields, and the book concludes with some topics which are more likely to be suitable for advanced students, namely, the analytic class number formula and the number field sieve. This is the fi...
There is a clear association between antibiotic use and resistance both on individual and population levels. In the European Union, countries with large antibiotic consumption have higher resistance rates. Antibiotic resistance leads to failed treatments, prolonged hospitalisations, increased costs and deaths. With few new antibiotics in the Research & Development pipeline, prudent antibiotic use is the only option to delay the development of resistance. Antibiotic policy consists of prescrib...
High-power hadron accelerators have strict limits on fractional beam loss. In principle, once a high-quality beam is set up in an acceptable state, beam loss should remain steady. However, in practice, there are many trips in operational machines, owing to excessive beam loss. This paper deals with monitoring equipment health to identify precursor signals that indicate an issue with equipment that will lead to unacceptable beam loss. To this end, a variety of equipment and beam signal measurements are described. In particular, several operational examples from the Spallation Neutron Source (SNS) of deteriorating equipment functionality leading to beam loss are reported.
Federal Laboratory Consortium — Purpose:The Aircraft Wiring Support Equipment Integration Laboratory (AWSEIL) provides a variety of research, design engineering and prototype fabrication services...
... STATE AND LOCAL ASSISTANCE Cooperative Agreements and Superfund State Contracts for Superfund Response Actions Personal Property Requirements Under A Cooperative Agreement § 35.6310 Obtaining equipment. To...
Changes to the 'Act respecting the use of petroleum products' have been announced effective May 1, 1999. The changes have been made to reduce problems which can be attributed to petroleum product leaks. The new regulations will make owners and users of petroleum equipment, including underground and above-ground storage equipment and commercial storage tanks, more accountable for the use of their own equipment. The emphasis in the new regulations is based upon the storage capacity of petroleum equipment and the risks associated with this equipment, rather than the on the activities of the owners concerned. Accordingly, the new regulations call for stricter requirements for high-risk equipment, a private equipment inspection plan, a two-year operating permit, replacing the current permits and certificates, a tariff structure based on the risks associated with the equipment, and deregulation of commercial activities involving petroleum products that require no equipment. Additionally, the amendments to the Act transfer responsibility for administration to the Regie du batiment and to the Ministere des Transports. Details of each of these changes are explained
Lehr, William H.; Pupillo, Lorenzo Maria
The Internet is now widely regarded as essential infrastructure for our global economy and society. It is in our homes and businesses. We use it to communicate and socialize, for research, and as a platform for E-commerce. In the late 1990s, much was predicted about what the Internet has become at present; but now, we have actual experience living with the Internet as a critical component of our everyday lives. Although the Internet has already had profound effects, there is much we have yet to realize. The present volume represents a third installment in a collaborative effort to highlight the all-encompassing, multidisciplinary implications of the Internet for public policy. The first installment was conceived in 1998, when we initiated plans to organize an international conference among academic, industry, and government officials to discuss the growing policy agenda posed by the Internet. The conference was hosted by the European Commission in Brussels in 1999 and brought together a diverse mix of perspectives on what the pressing policy issues would be confronting the Internet. All of the concerns identified remain with us today, including how to address the Digital Divide, how to modify intellectual property laws to accommodate the new realities of the Internet, what to do about Internet governance and name-space management, and how to evolve broadcast and telecommunications regulatory frameworks for a converged world.
This paper presents the results of a detailed study of wellhead equipment manufacturing costs in 11 countries in North America, Europe and Asia-Pacific. According to the Economist Intelligence Unit (EIU), Canada has a 5 per cent cost advantage and will be the best country in the world to do business between 2004 to 2008 because of its foreign trade policies, high quality infrastructure and market opportunities within the North American marketplace. KPMG Consulting developed a web-based cost model that allows investors to examine the costs involved in setting up and operating a business in more than 120 cities in Canada, the United States, the United Kingdom, France, Germany, Italy, Iceland, Luxembourg, the Netherlands, Japan and Australia. According to the model, a comparison of annual costs for oil and gas wellhead equipment manufacturing was presented for the 11 countries with reference to revenues, costs, and profits before and after income tax. In addition, Canada's research and development (R and D) cost advantage compared to the United States was presented, with reference to tax credits, expenditures, salaries, contracts, capital equipment, volume-based tax credits, and research studies. This report also includes a brief summary of 3 oil and gas companies that came to Canada and prospered. tabs., figs
Information provided for school districts desiring to offer distance education courses to their students describes the kind of satellite dish needed; its size, sturdiness, placement, and number of dishes needed; satellite receivers; the function of a descrambler; copyright restrictions; features of an Integrated Receiver/Descrambler; selecting a…
The field of real numbers is usually constructed using Dedekind cuts. In these thesis we focus on the construction of the field of real numbers using metric completion of rational numbers using Cauchy sequences. In a similar manner we construct the field of p-adic numbers, describe some of their basic and topological properties. We follow by a construction of complex p-adic numbers and we compare them with the ordinary complex numbers. We conclude the thesis by giving a motivation for the int...
From the late nineteenth century through 1974, France permitted immigration to furnish workers and to compensate for the low level of fertility. Intense immigration from North Africa, the economic crisis of the 1970s, and other factors led to policy changes in 1974. French immigration policy since 1974 has fluctuated between guaranteeing foreigners equal rights regardless of their religion, race, culture, or national origin, and attempting to differentiate among immigrants depending on their degree of assimilability to French culture. From 1974 to 1988, France had five different policies regarding whether to permit new immigration and what to do about illegal immigrants. In July 1984, the four major political parties unanimously supported a measure in Parliament that definitively guaranteed the stay in France of legal immigrants, whose assimilation thus assumed priority. Aid for return to the homeland was no longer to be widely offered, and immigration of unskilled workers was to be terminated except for those originating in European Community countries. Major changes of government in 1988 and 1993 affected only the modalities of applying these principles. The number of immigrants has fluctuated since 1974. Unskilled workers, the only category whose entrance was specifically controlled by the 1984 measures, have declined from 174,000 in 1970 to 25,000 in the early 1990s. The number of requests for political asylum declined from 60,000 in 1989 to 27,000 in 1993, and in 1991, 15,467 persons were granted refugee status. The number of immigrants of all types permitted to remain in France declined from 250,000 or 3000 per year in the early 1970s to around 110,000 at present. Although the decline is significant, it appears insufficient to the government in power since 1993. Although migratory flows are often explained as the product of imbalance in the labor market or in demographic growth, the French experience suggests that government policies, both in the sending and
We now apply the theory of the Thue equation to obtain an effective bound on m. Indeed, by Lemma 3.2, we can write m2 = ba3 and m2 − 4 = cd3 with b, c cubefree. By the above, both b, c are bounded since they are cubefree and all their prime factors are less than e63727. Now we have a finite number of. Thue equations:.
Worrell, Ernst; Ramesohl, Stephan; Boyd, Gale
Historically, most energy models were reasonably equipped to assess the impact of a subsidy or change in taxation, but are often insufficient to assess the impact of more innovative policy instruments. We evaluate the models used to assess future energy use, focusing on industrial energy use. We explore approaches to engineering-economic analysis that could help improve the realism and policy relevance of engineering-economic modeling frameworks. We also explore solutions to strengthen the policy usefulness of engineering-economic analysis that can be built from a framework of multi-disciplinary cooperation. We focus on the so-called ''engineering-economic'' (or ''bottom-up'') models, as they include the amount of detail that is commonly needed to model policy scenarios. We identify research priorities for the modeling framework, technology representation in models, policy evaluation and modeling of decision-making behavior.
This paper reports on the role of coal in establishing America's energy security. There is no mismatch of subject and keynote, for in the truest sense the author's topic is nothing less than the health and safety of the United States. Both will begin with the way we handle things in the coal mines at the working face. If energy policy were a piece of new equipment, the National Energy Strategy would be the equivalent of specifications---what the new hardware should be capable of doing. The National Energy Security Act of 1991 is the blueprint for the equipment. The hardware still must be assembled, tested and perfected. Undertaken between oil-related U.S. military deployments to stabilize the oil-exporting regions of the Persian Gulf that dominate world markets, the strategy has two objectives. There are multiple threats to America's energy security
The history of Hawaiian number systems is examined, and answers to questions regarding Hawaiian number words, including their origin and factors that influenced their development, are covered. A brief guide for pronouncing Hawaiian words is also provided. (MP)
Full Text Available Abstract. This research was aimed to analyze the excess inventories issue in pharmacy and medical equipment unit at a local hospital in Bandung which affected the service level of the hospital. As one of the busy hospital in Java, proven by the higher amount of the patient/year than in other average Java typical hospital, the hospital needs to concern about the pharmaceutical and medical equipment inventories in order to fulfill patients’ needs and in the same time keeping the inventory level under control. Therefore, an inventory control evaluation was conducted to determine the appropriate number of inventories and time of order to avoid the excessive goods in central warehouse of the hospital. By using probabilistic inventory model and continuous review policy, the pharmaceutical inventory in the hospital was calculated to compare the ideal and actual amount of the average inventory level (AIL. ABC (Always, Better, Control classification also classified in this research to identify the proper item which potentially can be reduced from the inventory. From the analysis, we have discovered that the hospital potentially able to reduce almost Rp 830 million or 57% from the overstock inventory level by using continuous review policy as the basis of inventory control calculation system. Keywords: Continuous review policy, inventory control, EOQ, ROP, AIL
Hamaguchi, Yoshikazu; Minakawa, Nobuaki
24 neutron scattering instruments are installed in the JRR-3M research reactor. Among them JAERI has 12 neutron scattering instruments. Those instruments are HRPD for high-resolution structural analysis, TAS-1 and TAS-2 for elastic and inelastic scattering and for magnetic scattering measurements by the polarized neutron, LTAS for elastic and inelastic scattering measurement at a low energy region, and for neutron device development, PNO for topography and for very small angle scattering measurement in a small Q range, NRG for neutron radiography, RESA for internal strain measurements, SANS for the molecule and semi-macroscopic magnetic structural analysis, BIX-2 and BIX-3 for the biological structural analysis research, and PGA for the research of prompt gamma-ray analysis. The university groups have 12 neutron scattering instruments. Since those instruments were installed at the period when JRR-3M was completed, about 10 years have passed. In order to match the old control systems with the progress of recent computer technologies, and peripheral equipment, numbers of instruments are being renewed. In the neutron guide hall of JRR-3M, the Ni mirror guide tube was replaced by a super mirror guide tube to increase neutron flux. The intensity of 2A flux was increased by a factor of about two. (J.P.N.)
The purpose of this report is to highlight energy efficiency policy action and planning in IEA member and key non-member countries over the period from September 2011 to September 2012. The report provides an overview of energy efficiency policy developments across the seven sectors covered by the IEA 25 Energy Efficiency Policy Recommendations (25 EEPR) – Cross-sectoral activities, Buildings, Appliances and Equipment, Lighting, Transport, Industry and Energy Providers.
Full Text Available EDITOR’S NOTEThis paper, written in December 2012, is a contribution to the ‘Policy Debate’ section of the International Development Policy. In this section, academics, policy makers and practitioners engage in a dialogue on global development challenges. Papers are copy-edited but not peer-reviewed. Instead, an initial thematic contribution is followed by critical comments and reactions from different stakeholders. This paper by Werner Thut is followed by reactions and analysis from a non-profit policy institute (Alexandra Gillies, Revenue Watch Institute, New York, ‘Crafting a Strategic Response to the Commodity-Development Conundrum’, a Southern scholar (Prof. Humberto Campodonico, Universidad Nacional Mayor de San Marcos, Lima ‘Going Beyond Transparency and Good Governance’ | ‘Más allá de la transparencia y una buena gobernanza’ and a representative of the trading sector (Stéphane Graber, Secretary General of Geneva Trading & Shipping Association – ‘Reassessing the Merchants’ Role in a Globalized Economy’.PAPER’S ABSTRACTSwitzerland is one of the world’s largest commodity trading hub. The author, senior policy adviser at the Swiss Agency for Development and Cooperation (SDC, reviews experiences and policy options related to commodity trading from a development policy perspective. While this sector has become of strategic importance to Switzerland’s economy, it also entails a number of risks. On the other hand, Swiss development cooperation efforts focus on several resource-rich countries, whose mineral and agricultural commodities are traded via Switzerland. How can Switzerland assist these countries to reap the benefits of their natural resource wealth? This paper looks at development policy aspects of commodity trading in relation to Swiss foreign and domestic policy. It examines ongoing policy debates in Switzerland and discusses development policy options.
The book includes several survey articles on prime numbers, divisor problems, and Diophantine equations, as well as research papers on various aspects of analytic number theory such as additive problems, Diophantine approximations and the theory of zeta and L-function Audience Researchers and graduate students interested in recent development of number theory
Elvik, Rune; Bjørnskau, Torkel
Highlights •26 studies of the safety-in-numbers effect are reviewed. •The existence of a safety-in-numbers effect is confirmed. •Results are consistent. •Causes of the safety-in-numbers effect are incompletely known....
Integrated Hatchery Operations Team (Northwest Power Planning Council, Portland, OR)
This document outlines regional policies and procedures for hatchery operations in the Columbia River Basin. The purpose of these policies is to provide regional guidelines by which all anadromous fish hatcheries will be operated. These policies will be adopted by the fisheries co-managers, and will provide guidance to operate hatcheries in an efficient and biologically sound manner. The hatchery policies presented in this manual are not intended to establish production priorities. Rather, the intent is to guide hatchery operations once production numbers are established. Hatchery operations discussed in this report include broodstock collection, spawning, incubation of eggs, fish rearing and feeding, fish release, equipment maintenance and operations, and personnel training. Decisions regarding production priorities must be provided by fishery managers through a comprehensive plan that addresses both natural and hatchery fish production. The Integrated Hatchery Operations Team is a multi-agency group called for by the Northwest Power Planning Council. This team was directed to develop new basinwide policies for managing and operating all existing and future anadromous fish hatcheries in the Columbia River Basin. The parties pledge to confer with each other and to use their authorities and resources to accomplish these mutually acceptable hatchery practices.
Full Text Available
ENGLISH ABSTRACT: The article makes the point that instrumentation is critical to the science and technology infrastructure. Furthermore, it reports the results of a relevant national survey. Information is available for three groups – (i research councils, (ii universities, and (iii technikons, museums and government departments as one group. This level of aggregation has been chosen in order to assist in the development of recommendations related to national policy. In addition, the state of equipment in the country is compared and contrasted with those in a number of countries abroad. Although it emerges that the Research Councils in South Africa possess the largest quantity of equipment, for the purpose of this paper, focus is given to the results of the Universities group since it is felt this provides greater ease of comparison to other developing countries.
AFRIKAANSE OPSOMMING: Die artikel beklemtoon dat instrumentasie krities is tot die wetenskap- en tegnologieinfrastruktuur. Verder rapporteer dit resultate van ‘n toepaslike nasionale ondersoek. Informasie word verskaf volgens drie kategorië, naamlik – (i Navorsingsrade, (ii Universiteite en (iii Universiteite van Tegnologie (Tegnikons, asook Museums en Staatsdepartemente. Hierdie samestelling is gekies om te help met die ontwikkeling van voorstelle t.o.v. ‘n nasionale riglyn. Die toestand van toerusting in die land word vergelyk met dié van verskeie internasionale lande. Alhoewel dit blyk dat die Navorsingsrade in Suid-Afrika die grootste hoeveelheid toerusting besit, vir die doel van hierdie dokument, is daar klem gelê op die Universiteitsgroep, omdat dit beskou word as meer vergelykbaar met die situasie in ander ontwikkelende lande.
Sobrevilla, L A
Peru's 1985 Population Policy Law states as its second objective that individuals and couples should be well informed and provided with the education and health services that will assist them in making responsible decisions about the number and spacing of their children. Thus, the law establishes a firm basis for IEC programs. With regard to population education, the purpose of the law is to create awareness through all educational channels of the reciprocal influence of population dynamics and socioeconomic development and to promote positive attitudes toward small family size. The law promotes the use of the communications media to educate and inform about population issues. The National Population Council, which coordinates and supervises the IEC activities of public sector agencies, has issued publications and audiovisual materials, conducted meetings with government officials and opinion leaders, and promoted awareness of population policy as a key part of development planning. In 1984, the Council organized the First National Seminar on Communication and Population to review activities, set the basis for intersectoral coordination, unify criteria, and review population policy concepts and language. The Ministry of Health carries out IEC activities as part of its family planning services program. In addition, the Ministry of Education has organized a national population education program that aims to revise school curricula to include a greater emphasis on population dynamics and family life education. The activities of a number of private institutions complement the IEC work public sector organizations.
... 21 Food and Drugs 7 2010-04-01 2010-04-01 false Equipment. 606.60 Section 606.60 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) BIOLOGICS CURRENT... following frequency, include but are not limited to: Equipment Performance check Frequency Frequency of...
... 50 Wildlife and Fisheries 6 2010-10-01 2010-10-01 false Audio equipment. 27.72 Section 27.72 Wildlife and Fisheries UNITED STATES FISH AND WILDLIFE SERVICE, DEPARTMENT OF THE INTERIOR (CONTINUED) THE... Audio equipment. The operation or use of audio devices including radios, recording and playback devices...
Rembovsky, Anatoly; Kozmin, Vladimir; Smolskiy, Sergey
Offers a unified approach to fundamental aspects of Automated Radio Monitoring (ARM). This book discusses the development, modeling, design, and manufacture of ARM systems. It provides classification and descriptions of modern high-efficient hardware-software ARM equipment, including the equipment for detection and radio direction-finding.
This document shows the general layout, and gives a part description for the weight/balance test equipment. This equipment will aid in the regulation of the leachate loading of tanker trucks. The report contains four drawings with part specifications. The leachate originates from lined trenches
Conclusion After 5 years of maintenance services, KNPP and AREVA have continuously intensified their partnership Close cooperation between KNPP, AREVA Local Office Engineers and OEM experts Involvement of sophisticated tools for diagnostics and condition monitoring Performance of engineering services and obsolescence evaluation Possibilities to perform equipment modernization of Electrical and IC equipment in future
This Compilation is devoted to equipment and techniques in the field of communications. It contains three sections. One section is on telemetry, including articles on radar and antennas. The second section describes techniques and equipment for coding and handling data. The third and final section includes descriptions of amplifiers, receivers, and other communications subsystems.
... 46 Shipping 4 2010-10-01 2010-10-01 false Equipment grounding. 129.370 Section 129.370 Shipping... INSTALLATIONS Power Sources and Distribution Systems § 129.370 Equipment grounding. (a) On a metallic vessel... grounding conductor must be sized to comply with section 250-95 of NEC (NFPA 70). (d) Each nonmetallic mast...
Kriikku, E.; Ward, C.; Stokes, M.; Randall, B.; Steed, J.; Jones, R.; Hamilton, L.
This report lists the operations required to complete the Can Loading steps on the Pu Immobilization Plant Flow Sheets and evaluates the equipment options to complete each operation. This report recommends the most appropriate equipment to support Plutonium Immobilization Can Loading operations
National Sanitation Foundation, Ann Arbor, MI.
This standard covers the sanitation requirements for equipment and/or devices used in the storage, preparation, or handling of foods and beverages. The National Sanitation Foundation's basic criteria for the evaluation of special equipment and/or devices has been prepared to fulfill several specific needs, its major function being to serve as a…
... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Watering equipment. 1250.67 Section 1250.67 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... of drinking water or other beverages, or for food preservation purposes, equipment constructed so as...
... 46 Shipping 7 2010-10-01 2010-10-01 false Diving equipment. 197.460 Section 197.460 Shipping COAST... GENERAL PROVISIONS Commercial Diving Operations Periodic Tests and Inspections of Diving Equipment § 197... in a dive under § 197.346 is inspected before each dive. ...
... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Refrigeration equipment. 1250.34 Section 1250.34 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED... SANITATION Food Service Sanitation on Land and Air Conveyances, and Vessels § 1250.34 Refrigeration equipment...
... 21 Food and Drugs 4 2010-04-01 2010-04-01 false Equipment construction. 211.65 Section 211.65 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) DRUGS... construction. (a) Equipment shall be constructed so that surfaces that contact components, in-process materials...
Mattsson, S.; Vano, E.
The International Commission on Radiological Protection (ICRP) does not have a specific publication or recent detailed advice on acceptability criteria and suspension levels for medical radiological equipment. However, a number of the Commission's publications clearly stress the need to carry out acceptance testing of radiological equipment. Such general recommendations are frequent in earlier and recent reports related to external radiation therapy. Over 30 y ago, the ICRP even included some examples of parameter accuracies concerning acceptance levels in connection with radiotherapy units. Later more general advices related to acceptability tests as important parts of various quality assurance programs were formulated for radiation therapy as well as for radiodiagnostics without going into details to give values for specific parameters. In the radiodiagnostic field, there are such general recommendations in reports related to equipment for X-ray interventional procedures, digital radiology and computed tomography. The ICRP highly supports the elaboration of detailed and clear acceptability and suspension criteria for equipment used in medical radiology carried out by organisations like International Atomic Energy Agency, International Electrotechnical Commission, European Commission, National Electrical Manufacturers Association (NEMA, USA) and others and consider such criteria as important parts of the quality programmes to guarantee good radiation safety conditions for patients in radiation therapy as well as in radiodiagnostics. (authors)
The paper provides an appraisal and synthesis of the regional innovation systems approach in relation to entrepreneurship policies. It addresses a number of areas where theoretical, empirical and policy-based issues are currently under-developed in relation to entrepreneurship and entrepreneurship policy.
The set of asymptotic numbers A as a system of generalized numbers including the system of real numbers R, as well as infinitely small (infinitesimals) and infinitely large numbers, is introduced. The detailed algebraic properties of A, which are unusual as compared with the known algebraic structures, are studied. It is proved that the set of asymptotic numbers A cannot be isomorphically embedded as a subspace in any group, ring or field, but some particular subsets of asymptotic numbers are shown to be groups, rings, and fields. The algebraic operation, additive and multiplicative forms, and the algebraic properties are constructed in an appropriate way. It is shown that the asymptotic numbers give rise to a new type of generalized functions quite analogous to the distributions of Schwartz allowing, however, the operation multiplication. A possible application of these functions to quantum theory is discussed
This textbook effectively builds a bridge from basic number theory to recent advances in applied number theory. It presents the first unified account of the four major areas of application where number theory plays a fundamental role, namely cryptography, coding theory, quasi-Monte Carlo methods, and pseudorandom number generation, allowing the authors to delineate the manifold links and interrelations between these areas. Number theory, which Carl-Friedrich Gauss famously dubbed the queen of mathematics, has always been considered a very beautiful field of mathematics, producing lovely results and elegant proofs. While only very few real-life applications were known in the past, today number theory can be found in everyday life: in supermarket bar code scanners, in our cars’ GPS systems, in online banking, etc. Starting with a brief introductory course on number theory in Chapter 1, which makes the book more accessible for undergraduates, the authors describe the four main application areas in Chapters...
Full Text Available Purpose of the article: The aim of the paper is to uncover ways of managing service offering provided by electrical equipment manufactures in the Czech Republic. The segment is extremely important for Czech industry nowadays, especially because of many companies being subcontractors for the car industry and mechanical engineering. The producers of electric equipment comply with the Czech industry classification CZ-NACE 27. Methodology/methods: The questionnaire in the form of the Likert scale was prepared to gather information about customer services. The respondents were usually directors or managers, e.g. employees with high competencies of knowing customer services in this particular market. The total of 22 companies were included in the survey. Research was focused on the following industries classifications belonging to CZ-NACE 27: CZ-NACE 27, CZ-NACE 271 and CZ-NACE 273. According to Czech Statistical Office the total number of companies belonging to these 3 segments is 136. It means 16,2% companies belonging to CZ-NACE 27 participated in our research. Basic statistical methods were used to analyse the complete database. Scientific aim: The paper deals with the problem of service offering provided by today’s manufacturers. Global understanding of services that manufacturers really develop, sell, deliver and manage is still limited. Findings: Managing service offering provided by today‘s manufacturers shows that 1 Manufacturers not offer only tangible products, but also wide range of services and even information and support. 2 New products are not designed only according to company technicians, but also according to their customers. Their products and services are developed, tested and improved according to their needs. 3 Services provide complex customer care from time product selection to its end. Conclusions: Manufacturers of tangible products need to enlarge their product offering to be able to satisfy customers. Therefore
Spicer, John Patrick; Chakraborty, Debejyo; Wincek, Michael Anthony; Wang, Hui; Abell, Jeffrey A; Bracey, Jennifer; Cai, Wayne W
A vibration welding system includes vibration welding equipment having a welding horn and anvil, a host device, a check station, and a robot. The robot moves the horn and anvil via an arm to the check station. Sensors, e.g., temperature sensors, are positioned with respect to the welding equipment. Additional sensors are positioned with respect to the check station, including a pressure-sensitive array. The host device, which monitors a condition of the welding equipment, measures signals via the sensors positioned with respect to the welding equipment when the horn is actively forming a weld. The robot moves the horn and anvil to the check station, activates the check station sensors at the check station, and determines a condition of the welding equipment by processing the received signals. Acoustic, force, temperature, displacement, amplitude, and/or attitude/gyroscopic sensors may be used.
This safety code is concerned with the protection of all individuals who may be exposed to radiation emitted by X-ray equipment operating at energies up to 1 MeV as used in industrial radiography. This code presents basic radiation safety information for the protection of personnel operating and servicing X-ray equipment and other workers and the general public in the vicinity of areas where X-ray equipment is in operation. It specifies general safety features of design, construction and functioning of X-ray equipment and facilities; describes the responsibilities of the user, operator and maintenance personnel; contains recommendations to ensure that the X-ray equipment is used and maintained in accordance with the ALARA principle; and describes a program of personnel monitoring and radiation safety surveys. ( 6 refs., 5 tabs., 4 figs.)
Dong, R.G.; Smith, P.D.
The Lawrence Livermore National Laboratory (LLNL) under the sponsorship of the US Nuclear Regulatory Commission (NRC) has developed this program plan for research in equipment qualification (EQA). In this report the research program which will be executed in accordance with this plan will be referred to as the Equipment Qualification Research Program (EQRP). Covered are electrical and mechanical equipment under the conditions described in the OBJECTIVE section of this report. The EQRP has two phases; Phase I is primarily to produce early results and to develop information for Phase II. Phase I will last 18 months and consists of six projects. The first project is program management. The second project is responsible for in-depth evaluation and review of EQ issues and EQ processes. The third project is responsible for detailed planning to initiate Phase II. The remaining three projects address specific equipment; i.e., valves, electrical equipment, and a pump
Heisler, S.W. Jr.; Mihalovich, G.S.
The Feed Materials Production Center (FMPC) is the United States Department of Energy's storage facility for thorium. FMPC thorium handling and overpacking projects ensure the continued safe handling and storage of the thorium inventory until final disposition of the materials is determined and implemented. The handling and overpacking of the thorium materials requires the design of a system that utilizes remote handling and overpacking equipment not currently utilized at the FMPC in the handling of uranium materials. The use of remote equipment significantly reduces radiation exposure to personnel during the handling and overpacking efforts. The design system combines existing technologies from the nuclear industry, the materials processing and handling industry and the mining industry. The designed system consists of a modified fork lift truck for the transport of thorium containers, automated equipment for material identification and inventory control, and remote handling and overpacking equipment for material identification and inventory control, and remote handling and overpacking equipment for repackaging of the thorium materials
The personal protection equipment is studied in the legal way (legal liabilities, certification, European texts), technical way (ergonomics, painfulness of ventilated equipment wearing, reliability of a respirable air line, protection gloves against the chemical risk, exposure to nano particulates, working in hot area), human factors (hostile area and emotion management), studies on personal equipment such evaluation, efficiency, conception of new equipment, physiological tolerance, limit of use, and some general safety studies on the working places. (N.C.)
Joo, Po Kook; Lim, Nam Jin; Lee, Young Gun
This study is carried out by KEARI(Korea Atomic Energy Research Institute) as the lead organization in cooperation with KIMM(Korea Institute of Machinery and Materials), KTL(Korea Testing Laboratory) and KRISS(Korea Research Institute of Standards and Science) to construct a basis of efficient management of nuclear equipment qualification business by expanding test equipment of each of participating organization, and developing qualification technologies. As for KIMM, control system of large scale shaker was replaced with advanced system, and LOCA(Loss of Coolant Accident) test facility was installed. KTL is now capable of conducting seismic tests of nuclear I and C as a result of installation of seismic test equipment during the first two project years. KRISS participated in the Project with a view to have large scale EMI test equipment and related technologies. In parallel with expansion of test equipment, a industrial-educational-research cooperation committee, as an intermediate step toward integrated equipment qualification system to maximize the usage of test equipment, was established and cooperation methods were investigated. As a result, Korea Nuclear Equipment Qualification Association, an corporate juridical person, was established. Research on development of thermal and radiation aging test technology of nuclear materials was carried out by Hanyang University and SECO(Saehan Engineering and Qualification Co., Ltd.). Integrated Equipment Qualification Database was developed which contains material test data, equipment qualification data and other EQ related informations. Standard qualification procedures were developed in order for test laboratories and manufacturers to establish design requirements and to efficiently perform tests
Skaler, F.; Djetelic, N.
Operation that is safe, reliable, effective and acceptable to public is the common message in a mission statement of commercial nuclear power plants (NPPs). To fulfill these goals, nuclear industry, among other areas, has to focus on: 1 Human Performance (HU) and 2 Equipment Reliability (EQ). The performance objective of HU is as follows: The behaviors of all personnel result in safe and reliable station operation. While unwanted human behaviors in operations mostly result directly in the event, the behavior flaws either in the area of maintenance or engineering usually cause decreased equipment reliability. Unsatisfied Human performance leads even the best designed power plants into significant operating events, which can be found as well-known examples in nuclear industry. Equipment reliability is today recognized as the key to success. While the human performance at most NPPs has been improving since the start of WANO / INPO / IAEA evaluations, the open energy market has forced the nuclear plants to reduce production costs and operate more reliably and effectively. The balance between these two (opposite) goals has made equipment reliability even more important for safe, reliable and efficient production. Insisting on on-line operation by ignoring some principles of safety could nowadays in a well-developed safety culture and human performance environment exceed the cost of electricity losses. In last decade the leading USA nuclear companies put a lot of effort to improve equipment reliability primarily based on INPO Equipment Reliability Program AP-913 at their NPP stations. The Equipment Reliability Program is the key program not only for safe and reliable operation, but also for the Life Cycle Management and Aging Management on the way to the nuclear power plant life extension. The purpose of Equipment Reliability process is to identify, organize, integrate and coordinate equipment reliability activities (preventive and predictive maintenance, maintenance
Hotta, Tracey A
Do you really need to have a policy and procedure in the office? Frequently they are seen sitting on the shelf, collecting dust. The answer is yes for a number of very important reasons. A policy and procedure manual is a tool to set guidelines and expectations on the basis of the mission and vision of the office. A well-written manual is a powerful training tool for new staff so they can get a feel for the office culture. Furthermore, it is a provincial or state legislative requirement that can reduce management's concern about potential legal issues or problems. If an office does not have a manual to set guidelines, the employees may be forced to make their own decisions to solve problems, which can often result in confusion, inconsistencies, and mistakes.
Roberson, Judy A.; Webber, Carrie A.; McWhinney, Marla C.; Brown, Richard E.; Pinckard, Marageret J.; Busch, John F.
This research was conducted in support of two branches of the EPA ENERGY STAR program, whose overall goal is to reduce, through voluntary market-based means, the amount of carbon dioxide emitted in the U.S. The primary objective was to collect data for the ENERGY STAR Office Equipment program on the after-hours power state of computers, monitors, printers, copiers, scanners, fax machines, and multi-function devices. We also collected data for the ENERGY STAR Commercial Buildings branch on the types and amounts of miscellaneous plug-load equipment, a significant and growing end use that is not usually accounted for by building energy managers. For most types of miscellaneous equipment, we also estimated typical unit energy consumption in order to estimate total energy consumption of the miscellaneous devices within our sample. This data set is the first of its kind that we know of, and is an important first step in characterizing miscellaneous plug loads in commercial buildings. The main purpose of this study is to supplement and update previous data we collected on the extent to which electronic office equipment is turned off or automatically enters a low power state when not in active use. In addition, it provides data on numbers and types of office equipment, and helps identify trends in office equipment usage patterns. These data improve our estimates of typical unit energy consumption and savings for each equipment type, and enables the ENERGY STAR Office Equipment program to focus future effort on products with the highest energy savings potential. This study expands our previous sample of office buildings in California and Washington DC to include education and health care facilities, and buildings in other states. We report data from sixteen commercial buildings in California, Georgia, and Pennsylvania: four education buildings, two medical buildings, two large offices (> 500 employees each), three medium offices (50-500 employees each), and five small
624.042.8:539.41 PROBLEMS OF EXPLOSION SAFETY IN INDUSTRIAL BUILDINGS. LOADS AND CALCULATION OF STRUCTURAL DESIGNS Moscow STROITEL’NAYA MEKHANIKA I...bibliography) the authors discuss first the works devoted to a general discussion of the problem of safety measures against explosions in industrial...developer (ammonium chloride). A description is given for the device for determining electro- graphic images. Sulphur, camphor , rosin, and tobacco
is based on plant data on 139 sections of butt-welded seams made by manual arc welding. In ultrasonic flaw detection the sizes of defects were...Russian. 1/1 USSR UDC 621.822.71 VOLOKUSHIN, V. F., Engineer, Eighteenth State Bearing Plant , Vin- nitsa CAUSES OF THE FORMATION OF TROOSTITE SPOTS...regarding the so-called tropism of the system and the property that prevents it from approaching an obstacle at a distance less than a certain safe value
... 40 Protection of Environment 24 2010-07-01 2010-07-01 false Number and gender. 205.3 Section 205.3... EQUIPMENT NOISE EMISSION CONTROLS General Provisions § 205.3 Number and gender. As used in this part, words in the -singular shall be deemed to import -the plural, and words in the masculine -gender shall be...
... 40 Protection of Environment 24 2010-07-01 2010-07-01 false Number and gender. 204.3 Section 204.3... STANDARDS FOR CONSTRUCTION EQUIPMENT General Provisions § 204.3 Number and gender. As used in this part, words in the singular shall be deemed to import the plural, and words in the masculine gender shall be...
... 49 Transportation 4 2010-10-01 2010-10-01 false Number and location. 230.51 Section 230.51 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION... Water Glasses and Gauge Cocks § 230.51 Number and location. Every boiler shall be equipped with at least...
Number theory is the branch of mathematics concerned with the counting numbers, 1, 2, 3, … and their multiples and factors. Of particular importance are odd and even numbers, squares and cubes, and prime numbers. But in spite of their simplicity, you will meet a multitude of topics in this book: magic squares, cryptarithms, finding the day of the week for a given date, constructing regular polygons, pythagorean triples, and many more. In this revised edition, John Watkins and Robin Wilson have updated the text to bring it in line with contemporary developments. They have added new material on Fermat's Last Theorem, the role of computers in number theory, and the use of number theory in cryptography, and have made numerous minor changes in the presentation and layout of the text and the exercises.
Jørgensen, Claus Bjørn; Suetens, Sigrid; Tyran, Jean-Robert
numbers based on recent drawings. While most players pick the same set of numbers week after week without regards of numbers drawn or anything else, we find that those who do change, act on average in the way predicted by the law of small numbers as formalized in recent behavioral theory. In particular......We investigate the “law of small numbers” using a unique panel data set on lotto gambling. Because we can track individual players over time, we can measure how they react to outcomes of recent lotto drawings. We can therefore test whether they behave as if they believe they can predict lotto......, on average they move away from numbers that have recently been drawn, as suggested by the “gambler’s fallacy”, and move toward numbers that are on streak, i.e. have been drawn several weeks in a row, consistent with the “hot hand fallacy”....
A new simple geometrical interpretation of complex numbers is presented. It differs from their usual interpretation as points in the complex plane. From the new point of view the complex numbers are rather operations on vectors than points. Moreover, in this approach the real, imaginary and complex numbers have similar interpretation. They are simply some operations on vectors. The presented interpretation is simpler, more natural, and better adjusted to possible applications in geometry and ...
Mei, Lin; Zhang, Kai; Hongqiang, Guo
In the flexible automatic line, the equipment is complex, the control mode is flexible, how to realize the large number of step and servo motor information interaction, the orderly control become a difficult control. Based on the existing flexible production line, this paper makes a comparative study of its network strategy. After research, an Ethernet + PROFIBUSE communication configuration based on PROFINET IO and profibus was proposed, which can effectively improve the data interaction efficiency of the equipment and stable data interaction information.
Doukas, Nikolaos; Bardis, Nikolaos G.
Speech recognition systems allow human - machine communication to acquire an intuitive nature that approaches the simplicity of inter - human communication. Small vocabulary speech recognition is a subset of the overall speech recognition problem, where only a small number of words need to be recognized. Speaker independent small vocabulary recognition can find significant applications in field equipment used by military personnel. Such equipment may typically be controlled by a small number of commands that need to be given quickly and accurately, under conditions where delicate manual operations are difficult to achieve. This type of application could hence significantly benefit by the use of robust voice operated control components, as they would facilitate the interaction with their users and render it much more reliable in times of crisis. This paper presents current challenges involved in attaining efficient and robust small vocabulary speech recognition. These challenges concern feature selection, classification techniques, speaker diversity and noise effects. A state machine approach is presented that facilitates the voice guidance of different equipment in a variety of situations.
Suetens, Sigrid; Galbo-Jørgensen, Claus B.; Tyran, Jean-Robert Karl
as formalized in recent behavioral theory. In particular, players tend to bet less on numbers that have been drawn in the preceding week, as suggested by the ‘gambler’s fallacy’, and bet more on a number if it was frequently drawn in the recent past, consistent with the ‘hot-hand fallacy’.......We investigate the ‘law of small numbers’ using a data set on lotto gambling that allows us to measure players’ reactions to draws. While most players pick the same set of numbers week after week, we find that those who do change react on average as predicted by the law of small numbers...
Full Text Available Measuring reaction times to number comparisons is thought to reveal a processing stage in elementary numerical cognition linked to internal, imprecise representations of number magnitudes. These intuitive representations of the mental number line have been demonstrated across species and human development but have been little explored in decision making. This paper develops and tests hypotheses about the influence of such evolutionarily ancient, intuitive numbers on human decisions. We demonstrate that individuals with more precise mental-number-line representations are higher in numeracy (number skills consistent with previous research with children. Individuals with more precise representations (compared to those with less precise representations also were more likely to choose larger, later amounts over smaller, immediate amounts, particularly with a larger proportional difference between the two monetary outcomes. In addition, they were more likely to choose an option with a larger proportional but smaller absolute difference compared to those with less precise representations. These results are consistent with intuitive number representations underlying: a perceived differences between numbers, b the extent to which proportional differences are weighed in decisions, and, ultimately, c the valuation of decision options. Human decision processes involving numbers important to health and financial matters may be rooted in elementary, biological processes shared with other species.
Diamond, Harold G; Cheung, Man Ping
"Generalized numbers" is a multiplicative structure introduced by A. Beurling to study how independent prime number theory is from the additivity of the natural numbers. The results and techniques of this theory apply to other systems having the character of prime numbers and integers; for example, it is used in the study of the prime number theorem (PNT) for ideals of algebraic number fields. Using both analytic and elementary methods, this book presents many old and new theorems, including several of the authors' results, and many examples of extremal behavior of g-number systems. Also, the authors give detailed accounts of the L^2 PNT theorem of J. P. Kahane and of the example created with H. L. Montgomery, showing that additive structure is needed for proving the Riemann hypothesis. Other interesting topics discussed are propositions "equivalent" to the PNT, the role of multiplicative convolution and Chebyshev's prime number formula for g-numbers, and how Beurling theory provides an interpretation of the ...
Number and geometry are the foundations upon which mathematics has been built over some 3000 years. This book is concerned with the logical foundations of number systems from integers to complex numbers. The author has chosen to develop the ideas by illustrating the techniques used throughout mathematics rather than using a self-contained logical treatise. The idea of proof has been emphasised, as has the illustration of concepts from a graphical, numerical and algebraic point of view. Having laid the foundations of the number system, the author has then turned to the analysis of infinite proc
Numbers are fascinating. The fascination begins in childhood, when we first learn to count. It continues as we learn arithmetic, algebra, geometry, and so on. Eventually, we learn that numbers not only help us to measure the world, but also to understand it and, to some extent, to control it. In The Adventure of Numbers, Gilles Godefroy follows the thread of our expanding understanding of numbers to lead us through the history of mathematics. His goal is to share the joy of discovering and understanding this great adventure of the mind. The development of mathematics has been punctuated by a n
research should be conducted to test the possibility and to verify the definition of such performance ratio including Takt time on those processes of which its operating time is possibly to be reduced, especially those are not constant and fixed. This piece of research is temporarily done on the process where its operating time is constant from time to time and there is no ideal cycle time possible.Practical implications: The awareness of the overproduction should be emphasized and raised in the intention of pursuing higher OEE value. As the definition proposed such, the process with constant cycle time could even be defined in different performance ratio from time to time regarding to the customer demands and corresponding production rate. These two variables can be adjusted and balanced to increase the OEE value through optimization of average cycle time. Over this, optimization of average cycle time on equipment with constant operating time can be achieved through the optimization of loading number per each processing.Originality/value: The novelty of the paper is the inclusion of customer demand in obtaining OEE value of any particular equipment. Besides that, the equipment without ideal cycle time, which means those processes carried out in constant cycle time are possibly to be evaluated with performance ratio. As consequence of that, the machine utilization and capability used could be quantified and visualized using the performance ratio data of the OEE proposed.
This document presents the results of a task to evaluate Tank Waste Remediation System (TWRS) sampling equipment drawings and identifies drawings category as either essential, support, or general drawings. This report completes the drawing evaluation task as outlined in Engineering Task Plan For Truck 3 and 4 Drawing Compliance and Evaluation (Wilson, 1997). The scope of this report is limited to an evaluation and identification of drawing category for drawings of certain tank waste sampling equipment for which the TRWS Characterization Project has been assigned custody, including: vapor sampling, grab sampling, auger sampling, and all core sampling equipment (see LMHC Task Order 304). This report does not address drawings for other waste tank deployed equipment systems having similar assigned custody, such as, Light Duty Utility Arm (LDUA), Cone Penetrometer system, or Long Length Contaminated Equipment (LLCE). The LDUA drawings are addressed in the Characterization Equipment Essential Drawings (HNF 1998). The Cone Penetrometer system drawings which are vendor drawings (not H- series) is not currently turned over to operations for deployment. The LLCE equipment was just recently assigned to Characterization Project and were not included in the original scope for this evaluation and will be addressed in the evaluation update scheduled for fiscal year 1999
This document presents the results of a task to update the evaluation of River Protection Project (WP) sampling equipment drawings and updates the assigned drawings category as either essential, support, or general drawings. This report updates the drawing evaluation that was originally done per Engineering Task Plan For Truck 3 and 4 Drawing Compliance and Evaluation. The scope of this report is limited to updating the evaluation and identification of drawing category for drawings of certain tank waste sampling equipment for which the RPP Characterization Project has been assigned custody, including: vapor sampling, grab sampling, auger sampling, all core sampling equipment, and Light Duty Utility Arm (LDUA) (see LMHC contract No. 519, release 10). This report does not address drawings for other waste tank deployed equipment systems having similar assigned custody, such as, Cone Penetrometer system, or Long Length Contaminated Equipment (LLCE). The Cone Penetrometer system, which is depicted on vendor drawings, (not H- series), is not currently turned over to operations for deployment. The LLCE equipment was just recently assigned to Characterization Project and was not included in the original scope for this update and will be addressed in the evaluation update scheduled for later in fiscal year 1999, when equipment ownership is determined
Atkey, Kayla; Elliott-Moyer, Pat; Freimanis, Miri; Raine, Kim D
Municipal buildings and corporate events in the City of Hamilton, Ontario. In 2011, the City of Hamilton adopted a healthy food and beverage policy. The intent of the policy is to demonstrate the City's commitment to healthy eating by providing food and beverages that are healthy, safe, and free of industrially produced trans fats, and promoting a sustainable, local food system. The corporate policy applies to all City facilities, meetings and events. In this article, we explore adoption and implementation of the policy, as well as key lessons for healthy public policy change. Integrating the policy into corporate culture and practice through the provision of ongoing supports and resources helped the City of Hamilton overcome barriers and achieve implementation success. Through exploration of the City of Hamilton's healthy food and beverage policy, we identified a number of lessons for policy change and implementation. When viewed in context, these lessons may help to support policy work in other Canadian jurisdictions.
The purpose of this document is to provide the maintenance requirements of the Long Length Contaminated Equipment (LLCE) trailers and provide a basis for the maintenance frequencies selected. This document is applicable to the LLCE Receiver trailer and Transport trailer assembled by Mobilized Systems Inc. (MSI). Equipment used in conjunction with, or in support of, these trailers is not included. This document does not provide the maintenance requirements for checkout and startup of the equipment following the extended lay-up status which began in the mid 1990s. These requirements will be specified in other documentation
Abd Nasir Ibrahim; Azali Muhammad; Ab Razak Hamzah; Abd Aziz Mohamed; Mohammad Pauzi Ismail
The following topics related to the equipment for x - and gamma ray radiography are discussed in this chapter. The topics are x-ray source for Industrial Radiography: properties of x-ray, generation of x-ray, mechanism of x-ray production, x-ray equipment, power supply, distribution of x-ray intensity along the tube: gamma ray source for Industrial Radiography: properties of gamma rays, gamma ray sources, gamma ray projectors on cameras, source changing. Care of Radiographic Equipments: Merits and Demerits of x and Gamma Rays
Szasz, T.; Nagy Czirok, Cs.; Batki, L.; Antal, S.
The patent of a dose-rate controlling equipment that can be attached to X-ray image-amplifiers is presented. In the new equipment the current of the photocatode of the image-amplifier is led into the regulating unit, which controls the X-ray generator automatically. The advantages of the equipment are the following: it can be simply attached to any type of X-ray image-amplifier, it accomplishes fast and sensitive regulation, it makes possible the control of both the mA and the kV values, it is attached to the most reliable point of the image-transmission chain. (L.E.)
Baldwin, N.M.; Barlow, C.R. [Uranium Enrichment Organization, Oak Ridge, TN (United States)
Strongly exothermic reactions can occur between equipment structural components and process gases under certain accident conditions in the diffusion enrichment cascades. This paper describes the conditions required for initiation of these reactions, and describes the range of such reactions experienced over nearly 50 years of equipment operation in the US uranium enrichment program. Factors are cited which can promote or limit the destructive extent of these reactions, and process operations are described which are designed to control the reactions to minimize equipment damage, downtime, and the possibility of material releases.
Diaz-Roldan; Carmelo Monteagudo-Cuerva
In the particular policy framework of a monetary union, the management of fiscal policy becomes an issue of special relevance, because the fiscal discipline imposed by the monetary agreements could limit the scope of stabilization fiscal policies, and its implications on economic growth. Therefore, is not trivial to manage fiscal policy in such particular economic framework. In this paper we will review the implications of fiscal policy in open economies. But we will pay special attention to ...
Home; Journals; Resonance – Journal of Science Education; Volume 3; Issue 7. The Class Number Problem - An Introduction to Algebraic Number Theory. Rajat Tandon. General ... Author Affiliations. Rajat Tandon1. Department of Mathematics, University of Hyderabad, Central University P.O., Hyderabad 500 046, India ...
Home; Journals; Resonance – Journal of Science Education; Volume 3; Issue 7. The Class Number Problem - An Introduction to Algebraic Number Theory. Rajat Tandon. General Article Volume 3 Issue 7 July 1998 pp 28-37. Fulltext. Click here to view fulltext PDF. Permanent link:
The Class Number Problem. 2. An Introduction to Algebraic Number Theory. Rajat Tandon received his PhD from Yale. University, USA. After an initial period as a visiting post-doctoral fellow at. TIFR, he joined the faculty of the North. Eastern Hill University, where he taught for a few years. For about two decades now, he ...
Levin, Bruce R; McCall, Ingrid C.; Perrot, Veronique
We postulate that the inhibition of growth and low rates of mortality of bacteria exposed to ribosome-binding antibiotics deemed bacteriostatic can be attributed almost uniquely to these drugs reducing the number of ribosomes contributing to protein synthesis, i.e., the number of effective riboso...
Given a positive integer n, is there a simple criterion which enables us to decide whether or not n is congruent? A few remarks are in order. To start with, if we ..... In other words 1 is a congruent number. Combining Propositions 2 and 3 with the fact that 1 is a non-congruent number, we deduce Fermat's last theorem for n=4.
Clemesha, David J.
Describes how a second-grade class used large templates to draw and paint five-digit numbers. The lesson integrated artistic knowledge and vocabulary with their mathematics lesson in place value. Students learned how draftspeople use templates, and they studied number paintings by Charles Demuth and Jasper Johns. (KM)
Spicer, John Patrick; Cai, Wayne W.; Chakraborty, Debejyo; Mink, Keith
A vibration welding system includes vibration welding equipment having a welding horn and anvil, a host machine, a check station, and a welding robot. At least one displacement sensor is positioned with respect to one of the welding equipment and the check station. The robot moves the horn and anvil via an arm to the check station, when a threshold condition is met, i.e., a predetermined amount of time has elapsed or a predetermined number of welds have been completed. The robot moves the horn and anvil to the check station, activates the at least one displacement sensor, at the check station, and determines a status condition of the welding equipment by processing the received signals. The status condition may be one of the alignment of the vibration welding equipment and the wear or degradation of the vibration welding equipment.
Some 38 incidents involving patient overexposure due to malfunctions or defects in radiation equipment were notified to HSE between 1986 and 1990. Of these cases, 30 involved diagnostic X ray equipment, while the remainder involved nuclear medicine or radiotherapy equipment. Those cases involving X ray equipment are examined in detail and grouped into six categories. The numbers of patients affected varied. In one case an estimated 350 patients were affected: in another, 240; while 13 cases affected only a single patient. A very rough estimate of the collective effective dose equivalent in the 30 cases comes to 5 man sieverts. It is concluded that improvements are needed in fault finding procedures, and guidance is needed on consistent methods of dose estimation and reporting. Improvements for the longer term include the selection of reliable components during manufacture; application of HSE guidance in software design for programmable electronic systems; and equipment design to incorporate fault detection and inhibition of operation to prevent excessive exposures
Kaiser, J.; Phalippou, J.; Dumont, D.; Viellard, R. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires
Recent installations for detecting can-rupture in nuclear reactors use, in the measurement processing section, a digital computer, either completely or partially. The reliability of the system is limited by that of the computer, which represents a common point for the processing of data from the detector. In order to satisfy the demands imposed by safety considerations for the operation of the equipment it is necessary to consider the possibility of installing a second computer in certain cases. The use of a computer involves the presence as interface between the detection equipment and the computer itself, of sealers operating as integrators for the pulses produced by the detector. By adding a certain number of circuits to these sealers, it is possible to carry out the work now demanded of the computer, as far as the calculation is concerned. This reasoning has led us to a so-called 'decentralized' solution involving the construction of specialized equipment in the region of the prospector itself. We believe that this solution, apart from the reliability point of view, has definite economic advantages. In our solution, the common point in the processing of the data is now situated not in the zone of the production of results but further down, in the printing out of these results. Even in the case of an incident at the common point, the results are produced, exposed and compared to the alarm thresholds. In the case of a breakdown of the specialized equipment, the results from this prospector are no longer available but the others continue to operate. It seems that this solution is more reliable than that employing universal computers. By using an interchangeable drawer system (MULTIBLOC) it is possible to replace rapidly any of the specialized equipment which breaks down. The systematic use of integrated circuits (TTL) ensures an increased reliability of the equipment. (author) [French] Les installations recentes de detection de rupture de gaines
The Texas Department of Transportation : (TxDOT) operates a large fleet of on-road and : off-road equipment. Consequently, fleet : maintenance procedures (specifically preventive : maintenance such as oil changes) represent a : significant cost to th...
This article explores the process and rationale for designing a poster to support community nurses in selecting appropriate pressure-relieving equipment based on accurate risk assessment and correct pressure ulcer grading. The project was prompted by the requirement to update community nurses' knowledge and ensure pressure-relieving equipment selection was evidence-based and not reliant on personal preference. The 2012 NHS Midlands and East 'Stop the pressure' campaign provided community nurses with a framework for pressure ulcer prevention and management. The attention to support surfaces highlighted the need for appropriate equipment. However the tissue viability team found that the introduction of this pathway alone did not help with the practical issues of appropriate equipment selection. The poster was designed with consideration as to how adults learn, and by looking to the Plan, Do, Study, Act (PDSA) cycle. This provided the framework for enabling new ideas and changes to practice to be tested on a small scale before full implementation.
In a market survey of level measurement equipment from 42 manufacturers, which is based on different principles of measurement and which is used for different applications, the data of the various manufacturers is compiled. (orig./HP) [de
Bradshaw, F.W., Westinghouse Hanford
This report documents the conceptual design of the Hot Conditioning System Equipment. The Hot conditioning System will consist of two separate designs: the Hot Conditioning System Equipment; and the Hot Conditioning System Annex. The Hot Conditioning System Equipment Design includes the equipment such as ovens, vacuum pumps, inert gas delivery systems, etc.necessary to condition spent nuclear fuel currently in storage in the K Basins of the Hanford Site. The Hot Conditioning System Annex consists of the facility of house the Hot Conditioning System. The Hot Conditioning System will be housed in an annex to the Canister Storage Building. The Hot Conditioning System will consist of pits in the floor which contain ovens in which the spent nuclear will be conditioned prior to interim storage.
National Aeronautics and Space Administration — Exercise equipment for on-orbit or very low gravity use has been developed using springs or motors to provide a constant force for resistive exercise. These...
Hong, Seok Boong; Chung, Chong Eun; Hwang, In Koo; Koo, In Soo; Park, Bum; Kim, Soo Hee; Lee, Seong Joo; Kim, Min Seok; Choi, Wha Lim
- process equipment at PIEF, Chemical Analysis Team and RWFTF have been calibrated. - The electronic equipment and radiation equipment at RWTF and PIEF have been prepared. - Development and installation of integrated RMS software for Hanaro Cold Neutron Laboratory Building(CNLB) RMS, and development and performance upgrade of a portal monitor for CNLB. - Performance test of the Hardware/Software of digital unit controller has been performed, and functional upgrade of the Hardware/Software of stimulator for SMART MMIS performance test facility has also been performed. - A controller of high voltage power supply for a small electron beam generator and a controller for razer pinning and a remote monitoring apparatus of cathode power supply for a 0.2 Mev. small electron beam generator have been designed and fabricated. - Database construction for effective maintenance for the process equipment and radiation instruments are designed and constructed
... piers and foundations that are designed to be as permanent as the buildings that house the equipment, or... walls, ceilings or floors or without in some way impairing the building, must be included in the...
The safety code for Telegamma Therapy Equipment and Installations, (AERB/SC/MED-1) and safety code for Brachytherapy Sources, Equipment and Installations, (AERB/SC/MED-3) were issued by AERB in 1986 and 1988 respectively. These codes specified mandatory requirements for radiation therapy facilities, covering the entire spectrum of operations ranging from the setting up of a facility to its ultimate decommissioning, including procedures to be followed during emergency situations. The codes also stipulated requirements of personnel and their responsibilities. With the advent of new techniques and equipment such as 3D-conformal radiation therapy, intensity modulated radiation therapy, image guided radiation therapy, treatment planning system, stereotactic radiosurgery, stereotactic radiotherapy, portal imaging, integrated brachytherapy and endovascular brachytherapy during the last two decades, AERB desires that these codes be revised and merged into a single code titled Radiation Therapy Sources, Equipment, and Installations
Hong, Seok Boong; Chung, Chong Eun; Hwang, In Koo; Koo, In Soo; Park, Bum; Kim, Soo Hee; Lee, Seong Joo; Kim, Min Seok; Choi, Wha Lim [KAERI, Daejeon (Korea, Republic of)
- process equipment at PIEF, Chemical Analysis Team and RWFTF have been calibrated. - The electronic equipment and radiation equipment at RWTF and PIEF have been prepared. - Development and installation of integrated RMS software for Hanaro Cold Neutron Laboratory Building(CNLB) RMS, and development and performance upgrade of a portal monitor for CNLB. - Performance test of the Hardware/Software of digital unit controller has been performed, and functional upgrade of the Hardware/Software of stimulator for SMART MMIS performance test facility has also been performed. - A controller of high voltage power supply for a small electron beam generator and a controller for razer pinning and a remote monitoring apparatus of cathode power supply for a 0.2 Mev. small electron beam generator have been designed and fabricated. - Database construction for effective maintenance for the process equipment and radiation instruments are designed and constructed.
Data on football injuries acquired from surveillance sources and in-depth investigations are presented. Results of the study are summarized by descriptions of the accident sequence, diagnosis of the injury, and specific equipment involved in the injury. (JD)
The primary objective of this work was to transfer technology developed in the area of truck noise reduction to that of construction equipment. Included is information gathered from previous contracts, surveys of manufacturers, a noise impact ranking...
... $5.2 million in the Equipment in Use account on its trial balance. Starting with FY 1996, Defense Technology Security Administration financial data will be included in consolidated DoD financial statements...
... must have, at least, the following equipment: (1) Multiple propellers or propulsion devices. (2) Two... Charge, Marine Inspection. (8) A scramble net that can be rigged on either side of the standby vessel. (9... Officer in Charge, Marine Inspection. ...
Backes, Paul G.; Tso, Kam S.
Report discusses issues pertaining to control of single-arm robotic manipulator to remove and install interchangeable equipment modules. Presents preliminary control strategy intended to guide development of control algorithms, along with analyses of problems arising in implementing strategy.
The "Schedule of Average Annual Equipment Ownership Expense" is designed for use on Force Account bills of Contractors performing work for the Illinois Department of Transportation and local government agencies who choose to adopt these rates. This s...
.... To test the process model, the system-level intrusion detection techniques and the working prototype of the intrusion detection system, a set of computer and network equipment has been purchased...
... STATEMENTS GUIDELINES FOR INDIVIDUAL DETERMINATIONS OF BASIC ESSENTIAL AIR SERVICE § 398.4 Equipment. (a... writing to the use of smaller aircraft to provide service at the place. (b) The aircraft must have at...
...) Radiation from capacitor energy storage equipment. Radiation emitted from the x-ray tube shall not exceed... charged, and the exposure switch, timer, or any discharge mechanism not activated. Compliance shall be...
This report examines the feasibility of remediating ancillary equipment associated with the 241-AX Tank Farm at the Hanford Site. Ancillary equipment includes surface structures and equipment, process waste piping, ventilation components, wells, and pits, boxes, sumps, and tanks used to make waste transfers to/from the AX tanks and adjoining tank farms. Two remedial alternatives are considered: (1) excavation and removal of all ancillary equipment items, and (2) in-situ stabilization by grout filling, the 241-AX Tank Farm is being employed as a strawman in engineering studies evaluating clean and landfill closure options for Hanford single-shell tanks. This is one of several reports being prepared for use by the Hanford Tanks Initiative Project to explore potential closure options and to develop retrieval performance evaluation criteria for tank farms
This report documents the conceptual design of the Hot Conditioning System Equipment. The Hot conditioning System will consist of two separate designs: the Hot Conditioning System Equipment; and the Hot Conditioning System Annex. The Hot Conditioning System Equipment Design includes the equipment such as ovens, vacuum pumps, inert gas delivery systems, etc.necessary to condition spent nuclear fuel currently in storage in the K Basins of the Hanford Site. The Hot Conditioning System Annex consists of the facility of house the Hot Conditioning System. The Hot Conditioning System will be housed in an annex to the Canister Storage Building. The Hot Conditioning System will consist of pits in the floor which contain ovens in which the spent nuclear will be conditioned prior to interim storage
Full Text Available The article is present new idea of the creation, developments and improvements of the electronic equipment of complex systems by means of the virtual electronic components. The idea of the virtual electronic components is a presentation and perception of the creation and developments of the equipment on two forming: real – in the manner of standard marketed block of the intellectual property and image – in the manner of virtual component. The real component in most cases slows the development of the electronic equipment. The imaginary component is the «locomotive» of development of the electronic equipment. The Imaginary component contains the scientific has brushed against developer. The scientific has brushed against developer reveals of itself in the manner of virtual component on the modern level of the design rates of microelectronics.
U.S. Environmental Protection Agency — Certified models meet all ENERGY STAR requirements as listed in the Version 1.0 ENERGY STAR Program Requirements for Electric Vehicle Supply Equipment that are...
Hurwitz, Justin (Gus); Layton, Roslyn
Around the world, telecommunications policy is one of the most important areas of public policy. The modern economy is driven by telecom technologies, and many telecom-related firms – Google, Apple, Facebook, and myriad fixed and mobile Internet service providers – are among the largest companies...... in the world. The Internet is opening up new platforms for business, education, government, and civic engagement. It has literally been a driving force in toppling governments. Telecommunications policy is important to every government in the world, and debates over what policies should be implemented......‟t stand up well to critical analysis. This paper collects and responds to a number of these premises that, collectively, underlie much popular, political, and academic support for increased telecommunications regulation in the United States and Europe – as well as much of the rest of the world....
Rosenquist, Greg; McNeil, Michael; Iyer, Maithili; Meyers, Steve; McMahon, Jim
, it is either impossible or more costly to improve the energy efficiency. Therefore, by not expanding or upgrading energy efficiency standards, opportunities for saving energy would be lost. In the past two decades, standards have significantly raised the level of energy efficiency for new products. How much more might be gained by making standards more stringent on products already subject to them, or by extending standards to products not yet covered? The main goal of this study is to estimate key national impacts of new and upgraded energy efficiency standards for residential and commercial equipment. These impacts approximate the opportunity for national benefits that may be lost if standards are not upgraded and expanded from current levels. This study also identifies the end uses where the largest opportunities exist. This analysis was prepared for the National Commission on Energy Policy (NCEP). It uses an analytical approach that is similar in concept to that used by the U.S. Department of Energy (DOE) to set standard levels. It relies on much less data and uses more simplified assumptions than the detailed and complex formulations used in DOE's standard-setting process. The results of this analysis should thus be viewed as a first approximation of the impacts that would actually be achieved by new standards. All monetary values in this report are in 2002 dollars.
Law, Eddie; Saxena, Achint
Besides providing network management to the Internet, it has become essential to offer different Quality of Service (QoS) to users. Policy-based management provides control on network routers to achieve this goal. The Internet Engineering Task Force (IETF) has proposed a two-tier architecture whose implementation is based on the Common Open Policy Service (COPS) protocol and Lightweight Directory Access Protocol (LDAP). However, there are several limitations to this design such as scalability and cross-vendor hardware compatibility. To address these issues, we present a functionally enhanced multi-tier policy management architecture design in this paper. Several extensions are introduced thereby adding flexibility and scalability. In particular, an intermediate entity between the policy server and policy rule database called the Policy Enforcement Agent (PEA) is introduced. By keeping internal data in a common format, using a standard protocol, and by interpreting and translating request and decision messages from multi-vendor hardware, this agent allows a dynamic Unified Information Model throughout the architecture. We have tailor-made this unique information system to save policy rules in the directory server and allow executions of policy rules with dynamic addition of new equipment during run-time.
Full Text Available Half a decade has passed since the fifth revision of the medical law and mandatory appointment of a medical equipment safety manager (MESM in hospitals in Japan. During this period, circumstances have changed regarding maintenance of medical equipment (ME. We conducted a survey to examine these changes and the current situation in ME management. Maintenance of ME and related work were found to have increased in many hospitals, but the number of clinical engineering technologists (CETs has only slightly increased. The appointed MESM was a CET or physician in most hospitals. In hospitals where physicians were appointed as the MESM, 81% had operation managers. Many respondents commented that it was difficult for one person to cover all the tasks required by the MESM, due to a lack of knowledge, too much work, or other reasons. This suggests the importance of an operation manager for ME to work under the MESM.
Ideal for a first course in number theory, this lively, engaging text requires only a familiarity with elementary algebra and the properties of real numbers. Author Underwood Dudley, who has written a series of popular mathematics books, maintains that the best way to learn mathematics is by solving problems. In keeping with this philosophy, the text includes nearly 1,000 exercises and problems-some computational and some classical, many original, and some with complete solutions. The opening chapters offer sound explanations of the basics of elementary number theory and develop the fundamenta
Kneusel, Ronald T
This is a book about numbers and how those numbers are represented in and operated on by computers. It is crucial that developers understand this area because the numerical operations allowed by computers, and the limitations of those operations, especially in the area of floating point math, affect virtually everything people try to do with computers. This book aims to fill this gap by exploring, in sufficient but not overwhelming detail, just what it is that computers do with numbers. Divided into two parts, the first deals with standard representations of integers and floating point numb
R. A. Mollin
Full Text Available A powerful number is a positive integer n satisfying the property that p2 divides n whenever the prime p divides n; i.e., in the canonical prime decomposition of n, no prime appears with exponent 1. In , S.W. Golomb introduced and studied such numbers. In particular, he asked whether (25,27 is the only pair of consecutive odd powerful numbers. This question was settled in  by W.A. Sentance who gave necessary and sufficient conditions for the existence of such pairs. The first result of this paper is to provide a generalization of Sentance's result by giving necessary and sufficient conditions for the existence of pairs of powerful numbers spaced evenly apart. This result leads us naturally to consider integers which are representable as a proper difference of two powerful numbers, i.e. n=p1−p2 where p1 and p2 are powerful numbers with g.c.d. (p1,p2=1. Golomb (op.cit. conjectured that 6 is not a proper difference of two powerful numbers, and that there are infinitely many numbers which cannot be represented as a proper difference of two powerful numbers. The antithesis of this conjecture was proved by W.L. McDaniel  who verified that every non-zero integer is in fact a proper difference of two powerful numbers in infinitely many ways. McDaniel's proof is essentially an existence proof. The second result of this paper is a simpler proof of McDaniel's result as well as an effective algorithm (in the proof for explicitly determining infinitely many such representations. However, in both our proof and McDaniel's proof one of the powerful numbers is almost always a perfect square (namely one is always a perfect square when n≢2(mod4. We provide in §2 a proof that all even integers are representable in infinitely many ways as a proper nonsquare difference; i.e., proper difference of two powerful numbers neither of which is a perfect square. This, in conjunction with the odd case in , shows that every integer is representable in
Careful organization and clear, detailed proofs characterize this methodical, self-contained exposition of basic results of classical algebraic number theory from a relatively modem point of view. This volume presents most of the number-theoretic prerequisites for a study of either class field theory (as formulated by Artin and Tate) or the contemporary treatment of analytical questions (as found, for example, in Tate's thesis).Although concerned exclusively with algebraic number fields, this treatment features axiomatic formulations with a considerable range of applications. Modem abstract te
The world around us is saturated with numbers. They are a fundamental pillar of our modern society, and accepted and used with hardly a second thought. But how did this state of affairs come to be? In this book, Leo Corry tells the story behind the idea of number from the early days of the Pythagoreans, up until the turn of the twentieth century. He presents an overview of how numbers were handled and conceived in classical Greek mathematics, in the mathematics of Islam, in European mathematics of the middle ages and the Renaissance, during the scientific revolution, all the way through to the
LeVeque, William J
This excellent textbook introduces the basics of number theory, incorporating the language of abstract algebra. A knowledge of such algebraic concepts as group, ring, field, and domain is not assumed, however; all terms are defined and examples are given - making the book self-contained in this respect.The author begins with an introductory chapter on number theory and its early history. Subsequent chapters deal with unique factorization and the GCD, quadratic residues, number-theoretic functions and the distribution of primes, sums of squares, quadratic equations and quadratic fields, diopha
""A very stimulating book ... in a class by itself."" - American Mathematical MonthlyAdvanced students, mathematicians and number theorists will welcome this stimulating treatment of advanced number theory, which approaches the complex topic of algebraic number theory from a historical standpoint, taking pains to show the reader how concepts, definitions and theories have evolved during the last two centuries. Moreover, the book abounds with numerical examples and more concrete, specific theorems than are found in most contemporary treatments of the subject.The book is divided into three parts
Ian Stewart explores the astonishing properties of numbers from 1 to10 to zero and infinity, including one figure that, if you wrote it out, would span the universe. He looks at every kind of number you can think of - real, imaginary, rational, irrational, positive and negative - along with several you might have thought you couldn't think of. He explains the insights of the ancient mathematicians, shows how numbers have evolved through the ages, and reveals the way numerical theory enables everyday life. Under Professor Stewart's guidance you will discover the mathematics of codes,
The subject of random number generation is currently controversial. Differing opinions on this subject seem to stem from implicit or explicit differences in philosophy; in particular, from differing ideas concerning the role of probability in the real world of physical processes, electronic computers, and Monte Carlo calculations. An attempt is made here to reconcile these views. The role of stochastic ideas in mathematical models is discussed. In illustration of these ideas, a mathematical model of the use of random number generators in Monte Carlo calculations is constructed. This model is used to set up criteria for the comparison and evaluation of random number generators. (U.S.)
Crossley, John N
This book presents detailed studies of the development of three kinds of number. In the first part the development of the natural numbers from Stone-Age times right up to the present day is examined not only from the point of view of pure history but also taking into account archaeological, anthropological and linguistic evidence. The dramatic change caused by the introduction of logical theories of number in the 19th century is also treated and this part ends with a non-technical account of the very latest developments in the area of Gödel's theorem. The second part is concerned with the deve
Fredy R. Zypman
Full Text Available We introduce, generate and study a family of supersymmetric displaced number states (SDNS that can be considered generalized coherent states of the supersymmetric harmonic oscillator. The family is created from the seminal supersymmetric boson-fermion entangling annihilation operator introduced by Aragone and Zypman and later expanded by Kornbluth and Zypman. Using the momentum representation, the states are obtained analytically in compact form as displaced supersymmetric number states. We study their position-momentum uncertainties, and their bunchiness by classifying them according to their Mandel Q-parameter in phase space. We were also able to find closed form analytical representations in the space and number basis.
Ierland, van E.C.; Gupta, J.; Kok, M.T.J.
Climate change is currently at the center of scientific and political debate, and the need for well-designed international climate policies is widely recognized. Despite this, the complexity of both the climate change problem and the international negotiation process has resulted in a large number