WorldWideScience

Sample records for pole face losses

  1. effect of number of rotor poles on ac losses of permanent magnet

    African Journals Online (AJOL)

    HOD

    A study on permanent magnet (PM) eddy current and core losses of dual-stator PM machines is investigated in this paper. The analyzed core losses include: the rotor core loss, stator core loss and the total core loss of the machines. Further, the effect of their different rotor pole number is also presented with quantitative ...

  2. CERN Proton Synchrotronworking point Matrix for extended pole face winding powering scheme

    CERN Document Server

    Freyermuth, P; Delrieux, M; Genoud, H; Gilardoni, S; Hanke, K; Hans, O; Mataguez, S; Metral, G; Peters, F; Steerenberg, R; Vandorpe, B

    2010-01-01

    The CERN Proton Synchrotron has been continuously improving its beam performances since 1959. The working point parameters of the accelerator are mainly controlled by dedicated windings installed on the poles of the main combined function magnets. In 2007, the power supplies of these windings were renovated and extended from three to five independent groups, allowing exploration of new working point settings. This configuration offers the flexibility of several adjustment strategies such as leaving one current free or to control an additional physical parameter, like Q′′ h. A non-linear chromaticity measurement campaign, at different beam momenta, resulted in matrices defining the relationship between the five pole face winding currents and the four beam parameters Qh, Qv, h, and v. Each cell of these matrices was fitted against momentum. The final result is a single matrix as a function of beam momentum, which is now used by the operational software to trim the working point. This paper summarises this m...

  3. Magnet losses in inverter-fed two-pole PM machines

    DEFF Research Database (Denmark)

    Gonzalez, Adolfo Garcia; Millinger, J.; Soulard, J.

    2016-01-01

    This article deals with the estimation of magnet losses in a permanent-magnet motor inserted in a nut-runner. This type of machine has interesting features such as being two-pole, slot-less and running at a high speed (30000 rpm). Two analytical models were chosen from the literature. A numerical...... estimation of the losses with 2D Finite Element Method was carried out. A detailed investigation of the effect of simulation settings (e.g., mesh size, time-step, remanence flux density in the magnet, superposition of the losses, etc.) was performed. Finally, calculation of losses with 3D-FEM were also run...

  4. Force Profiles of a Linear Switched Reluctance Motor Having Special Pole Face Shapes

    Directory of Open Access Journals (Sweden)

    CHADRESEKAR, V.

    2010-11-01

    Full Text Available In this paper, the results of a finite element analysis are carried out on an new stator geometry of a three phase longitudinal flux Linear Switched Reluctance Motor (LSRM. In the new geometry, pole shoes are affixed to the stator poles. Static and dynamic characteristics for the proposed structure have been highlighted. Motor performance for variable load conditions is discussed. Frequency spectrum analyses of force profile using the fast Fourier transform (FFT are described to predict the vibration frequencies. The 2-Dimensional (2-D finite element analysis (FEA and the experimental results of this paper prove that LSRMs are one of the strong candidates for linear propulsion drives.

  5. Human Bites of the Face with Tissue Losses in Cosmopolitan ...

    African Journals Online (AJOL)

    A retrospective series of thirty-six cases of human bites to the face with tissue losses requiring reconstruction during a five-year period, January 1999 to December 2003 is presented. The unmarried female in her third decade dominated both as victim and assailant in incidences related to love affairs and love gone sour.

  6. A new way of utilizing pole face windings and magnetic field corrections for independent tuning of betatron wave numbers and chromaticities in the CERN Proton Synchrotron

    CERN Document Server

    Gouiran, R

    1978-01-01

    Precise control of the quadrupole and sextupole components of the magnetic fields in focusing and defocusing sectors respectively was achieved by the combined use of pole-face and yoke windings with three separate power supplies synchronously programmed by a computer. Experience of this technique led to a new philosophy in the design of pole-face windings, in which they become an integral and active part of the magnet. With the arrangement described, focusing and guiding functions are partially separated and an old combined-function accelerator can be transformed effectively into a more flexible separate-function machine without any decrease in available straight- section space. (5 refs).

  7. Correcting intensity loss errors in the absence of texture-free reference samples during pole figure measurement

    International Nuclear Information System (INIS)

    Saleh, Ahmed A.; Vu, Viet Q.; Gazder, Azdiar A.

    2016-01-01

    Even with the use of X-ray polycapillary lenses, sample tilting during pole figure measurement results in a decrease in the recorded X-ray intensity. The magnitude of this error is affected by the sample size and/or the finite detector size. These errors can be typically corrected by measuring the intensity loss as a function of the tilt angle using a texture-free reference sample (ideally made of the same alloy as the investigated material). Since texture-free reference samples are not readily available for all alloys, the present study employs an empirical procedure to estimate the correction curve for a particular experimental configuration. It involves the use of real texture-free reference samples that pre-exist in any X-ray diffraction laboratory to first establish the empirical correlations between X-ray intensity, sample tilt and their Bragg angles and thereafter generate correction curves for any Bragg angle. It will be shown that the empirically corrected textures are in very good agreement with the experimentally corrected ones. - Highlights: •Sample tilting during X-ray pole figure measurement leads to intensity loss errors. •Texture-free reference samples are typically used to correct the pole figures. •An empirical correction procedure is proposed in the absence of reference samples. •The procedure relies on reference samples that pre-exist in any texture laboratory. •Experimentally and empirically corrected textures are in very good agreement.

  8. Attitudes toward Face-to-Face and Online Counseling: Roles of Self-Concealment, Openness to Experience, Loss of Face, Stigma, and Disclosure Expectations among Korean College Students

    Science.gov (United States)

    Bathje, Geoff J.; Kim, Eunha; Rau, Ellen; Bassiouny, Muhammad Adam; Kim, Taehoon

    2014-01-01

    This study examined attitudes toward face-to-face (f2f) and online counseling among 228 Korean college students. In addition, it tested a hypothesized model proposing that general propensities (i.e., self-concealment, openness to experience, and loss of face) would influence counseling-specific expectations (i.e., self-stigma and disclosure…

  9. Loss of PopZ At activity in Agrobacterium tumefaciens by Deletion or Depletion Leads to Multiple Growth Poles, Minicells, and Growth Defects.

    Science.gov (United States)

    Grangeon, Romain; Zupan, John; Jeon, Yeonji; Zambryski, Patricia C

    2017-11-14

    Agrobacterium tumefaciens grows by addition of peptidoglycan (PG) at one pole of the bacterium. During the cell cycle, the cell needs to maintain two different developmental programs, one at the growth pole and another at the inert old pole. Proteins involved in this process are not yet well characterized. To further characterize the role of pole-organizing protein A. tumefaciens PopZ (PopZ At ), we created deletions of the five PopZ At domains and assayed their localization. In addition, we created a popZ At deletion strain (Δ popZ At ) that exhibited growth and cell division defects with ectopic growth poles and minicells, but the strain is unstable. To overcome the genetic instability, we created an inducible PopZ At strain by replacing the native ribosome binding site with a riboswitch. Cultivated in a medium without the inducer theophylline, the cells look like Δ popZ At cells, with a branching and minicell phenotype. Adding theophylline restores the wild-type (WT) cell shape. Localization experiments in the depleted strain showed that the domain enriched in proline, aspartate, and glutamate likely functions in growth pole targeting. Helical domains H3 and H4 together also mediate polar localization, but only in the presence of the WT protein, suggesting that the H3 and H4 domains multimerize with WT PopZ At , to stabilize growth pole accumulation of PopZ At IMPORTANCE Agrobacterium tumefaciens is a rod-shaped bacterium that grows by addition of PG at only one pole. The factors involved in maintaining cell asymmetry during the cell cycle with an inert old pole and a growing new pole are not well understood. Here we investigate the role of PopZ At , a homologue of Caulobacter crescentus PopZ (PopZ Cc ), a protein essential in many aspects of pole identity in C. crescentus We report that the loss of PopZ At leads to the appearance of branching cells, minicells, and overall growth defects. As many plant and animal pathogens also employ polar growth

  10. Living with loss: middle-aged men face spousal bereavement.

    Science.gov (United States)

    Daggett, Luann M

    2002-05-01

    Spousal bereavement is one of the most profoundly disturbing events encountered in the human life span. Research has shown that conjugal bereavement has significant physical and psychological consequences for the surviving spouse. In American culture, men and women experience bereavement in different ways. The author used in-depth interviews in the tradition of phenomenology to collect data from 8 men aged 41 to 54 years who had experienced the death of their spouse within the previous 8 months to 6 years. The research revealed the lived experience of spousal bereavement to be a journey from the realization of irreconcilable loss through themes of responding to the loss and living through the loss toward reclamation and reconstruction of a life.

  11. Human Bites of the Face with Tissue Losses in Cosmopolitan ...

    African Journals Online (AJOL)

    Dr. Milaki Asuku

    Uchendu 6 working in the same center a decade later reported a five-year series consisting of 37 cases of human bite to the lip and tissue loss. In the western world human bites are more frequently encountered in institutions for the care of the developmentally disabled individuals as reported by Lindsey and colleagues 7.

  12. Hospitals face loss of federal tax-exempt status.

    Science.gov (United States)

    Nauert, R C; Sanborn, A B; MacKelvie, C F; Harvitt, J L

    1988-09-01

    Because of governmental challenges, not-for-profit hospitals can no longer take for granted their right to be tax exempt. The Internal Revenue Service is auditing nearly 1,500 tax-exempt healthcare organizations to determine how accurately they are reporting unrelated business income. At greatest risk are those hospital systems that have become overly acquisitive or have strayed from the charitable mission that originally entitled them to tax exemption. To protect their tax-exempt status, currently exempt healthcare institutions must be careful that any activities, such as joint ventures and affiliate corporations, conform to their charitable mission. In the face of tougher legislation and Federal scrutiny, hospitals must make sure they are devoted to and performing a charitable purpose if they want to keep their tax-exempt status.

  13. Veterinarians' role for pet owners facing pet loss

    Science.gov (United States)

    Fernandez-Mehler, P.; Gloor, P.; Sager, E.; Lewis, F. I.; Glaus, T. M

    2013-01-01

    Owners' satisfaction with, and expectations from, their veterinarians around euthanasia, including questions on disposal of pet remains subject to animal species, clients' gender, age, family conditions, area of living and type of veterinary clinic visited were evaluated by questionnaire. Questionnaires were to be filled out by clients consecutively visiting the individual practices and hospitals for any kind of consultations. Of 2350 questionnaires distributed, 2008 were returned and available for analysis. Owner satisfaction concerning the procedure of euthanasia was high (92 per cent, 1173/1272). After the event of euthanasia, 14 per cent (170/1250) had changed their veterinarian, even though 75 per cent of these 170 had been satisfied with the procedure. Most owners (88 per cent) expected veterinarians to talk about their pet's final destination, and 38 per cent expected this to happen early in the pet's life. For 81 per cent clients, the veterinarian was the primary informant about the possibilities concerning the disposal of pet remains, and 33 per cent indicated their veterinarian as the contact person to talk about pet loss. Area of living, or veterinary specialisation, only marginally influenced the answers. Veterinarians play an important role to inform their clients concerning questions around euthanasia and the care of pet remains, and to support them during the process of mourning. PMID:23492929

  14. Veterinarians' role for pet owners facing pet loss.

    Science.gov (United States)

    Fernandez-Mehler, P; Gloor, P; Sager, E; Lewis, F I; Glaus, T M

    2013-05-25

    Owners' satisfaction with, and expectations from, their veterinarians around euthanasia, including questions on disposal of pet remains subject to animal species, clients' gender, age, family conditions, area of living and type of veterinary clinic visited were evaluated by questionnaire. Questionnaires were to be filled out by clients consecutively visiting the individual practices and hospitals for any kind of consultations. Of 2350 questionnaires distributed, 2008 were returned and available for analysis. Owner satisfaction concerning the procedure of euthanasia was high (92 per cent, 1173/1272). After the event of euthanasia, 14 per cent (170/1250) had changed their veterinarian, even though 75 per cent of these 170 had been satisfied with the procedure. Most owners (88 per cent) expected veterinarians to talk about their pet's final destination, and 38 per cent expected this to happen early in the pet's life. For 81 per cent clients, the veterinarian was the primary informant about the possibilities concerning the disposal of pet remains, and 33 per cent indicated their veterinarian as the contact person to talk about pet loss. Area of living, or veterinary specialisation, only marginally influenced the answers. Veterinarians play an important role to inform their clients concerning questions around euthanasia and the care of pet remains, and to support them during the process of mourning.

  15. Faces

    DEFF Research Database (Denmark)

    Mortensen, Kristine Køhler; Brotherton, Chloe

    2018-01-01

    In this chapter, we investigate how a face is not a singular, invariable object, but may take on a variety of forms, and how new media has especially created new venues for the moldings of faces. We suggest that faces should be viewed in plural in order to emphasize the many different facial disp...

  16. Effects of sleep loss on emotion recognition: a dissociation between face and word stimuli.

    Science.gov (United States)

    Maccari, Lisa; Martella, Diana; Marotta, Andrea; Sebastiani, Mara; Banaj, Nerisa; Fuentes, Luis J; Casagrande, Maria

    2014-10-01

    Short-term sleep deprivation, or extended wakefulness, adversely affects cognitive functions and behavior. However, scarce research has addressed the effects of sleep deprivation (SD) on emotional processing. In this study, we investigated the impact of reduced vigilance due to moderate sleep deprivation on the ability to recognize emotional expressions of faces and emotional content of words. Participants remained awake for 24 h and performed the tasks in two sessions, one in which they were not affected by sleep loss (baseline; BSL), and other affected by SD, according to a counterbalanced sequence. Tasks were carried out twice at 10:00 and 4:00 am, or at 12:00 and 6:00 am. In both tasks, participants had to respond to the emotional valence of the target stimulus: negative, positive, or neutral. The results showed that in the word task, sleep deprivation impaired recognition irrespective of the emotional valence of words. However, sleep deprivation impaired recognition of emotional face expressions mainly when they showed a neutral expression. Emotional face expressions were less affected by the sleep loss, but positive faces were more resistant than negative faces to the detrimental effect of sleep deprivation. The differential effects of sleep deprivation on recognition of the different emotional stimuli are indicative of emotional facial expressions being stronger emotional stimuli than emotional laden words. This dissociation may be attributed to the more automatic sensory encoding of emotional facial content.

  17. Techniques for creating inconspicuous face-lift scars: avoiding visible incisions and loss of temporal hair.

    Science.gov (United States)

    Kridel, Russell W H; Liu, Edmund S

    2003-01-01

    Patients seeking rhytidectomy desire an improved neckline, jawline, and midface, but rarely at the price of signs that betray a face-lift, namely, visible incisions. We describe our face-lift incisional planning and the rationale behind specific surgical maneuvers for preventing unwanted sequelae. The telltale signs of poorly placed incisions include temporal hair loss, conspicuous scars, an unnatural appearance to the tragus, and a posterior hairline distorsion. Special considerations are given to the male patient and to the salvage of readily visible incision lines from previous surgery.

  18. Faces

    DEFF Research Database (Denmark)

    Mortensen, Kristine Køhler; Brotherton, Chloe

    2018-01-01

    for the face the be put into action. Based on an ethnographic study of Danish teenagers’ use of SnapChat we demonstrate how the face is used as a central medium for interaction with peers. Through the analysis of visual SnapChat messages we investigate how SnapChat requires the sender to put an ‘ugly’ face...... displays a single person make use of, and how this ‘pool of faces’ carries sociocultural meaning. While the past decades of swift technological development may seem to have diminished the role of face to face contact, the many new media has – on the contrary – established multiple new and innovative arenas...... forward. Especially the teenage girls engage in manipulating their faces into hideous expressions. However, this type of interaction is not random facial displays, but follow an ‘aesthetics of ugliness’. This aesthetics involve specific ways of looking ugly and is primarily performed by girls who have...

  19. The anatomy of the aging face: volume loss and changes in 3-dimensional topography.

    Science.gov (United States)

    Coleman, Sydney R; Grover, Rajiv

    2006-01-01

    Facial aging reflects the dynamic, cumulative effects of time on the skin, soft tissues, and deep structural components of the face, and is a complex synergy of skin textural changes and loss of facial volume. Many of the facial manifestations of aging reflect the combined effects of gravity, progressive bone resorption, decreased tissue elasticity, and redistribution of subcutaneous fullness. A convenient method for assessing the morphological effects of aging is to divide the face into the upper third (forehead and brows), middle third (midface and nose), and lower third (chin, jawline, and neck). The midface is an important factor in facial aesthetics because perceptions of facial attractiveness are largely founded on the synergy of the eyes, nose, lips, and cheek bones (central facial triangle). For aesthetic purposes, this area should be considered from a 3-dimensional rather than a 2-dimensional perspective, and restoration of a youthful 3-dimensional facial topography should be regarded as the primary goal in facial rejuvenation. Recent years have seen a significant increase in the number of nonsurgical procedures performed for facial rejuvenation. Patients seeking alternatives to surgical procedures include those who require restoration of lost facial volume, those who wish to enhance normal facial features, and those who want to correct facial asymmetry. Important factors in selecting a nonsurgical treatment option include the advantages of an immediate cosmetic result and a short recovery time.

  20. Front- and rear-facing horizontal sound localization results in adults with unilateral hearing loss and normal hearing.

    Science.gov (United States)

    Nelson, Erin; Reeder, Ruth M; Holden, Laura K; Firszt, Jill B

    2018-03-19

    Binaural hearing allows listeners to take advantage of auditory cues that are necessary for sound localization. Patients with asymmetric or unilateral hearing loss receive degraded or absent binaural cues and often demonstrate decreased sound localization in the horizontal plane. Given the importance of sound localization for everyday function, there is a need for clinically feasible methods to evaluate localization, particularly as validation of intervention for patients with unilateral hearing loss. The present study compared sound localization results obtained for front-facing and rear-facing soundfield systems and for a rear-facing head related transfer function (HRTF) system in two hearing groups, listeners with normal hearing and those with unilateral hearing loss. Results between the three systems were highly correlated and repeatable. Neither age nor a pure-tone average of 0.5, 1, 2 and 4 kHz correlated with localization performance among normal hearing participants. Among the UHL group, age and onset of severe to profound hearing loss were positively correlated with localization results; length of deafness was negatively correlated. Behavioral chance performance was established for localization with rear-facing HRTF and rear-facing soundfield test systems; group mean results for unilateral hearing loss participants were significantly better than chance. Continued work is needed in developing clinically feasible evaluation methods for patients with asymmetric or unilateral hearing loss, particularly as the effects of treatment options are assessed. Copyright © 2018 Elsevier B.V. All rights reserved.

  1. Epidemiologia das fraturas de face em crianças num pronto-socorro de uma metrópole tropical

    OpenAIRE

    Souza,Daniel Falbo Martins de; Santili,Cláudio; Freitas,Ronaldo Rodrigues de; Akkari,Miguel; Figueiredo,Marina Juliana Pita Sassioto Silveira de

    2010-01-01

    OBJETIVO: Realizar um estudo epidemiológico das fraturas de face em crianças em um serviço de urgência. MÉTODOS: Estudo retrospectivo de quarenta e dois pacientes com idades variando entre zero a 17 anos, portadores de fraturas de face, tratados no Setor de Cirurgia Buco-Maxilo-Facial da Santa Casa de São Paulo, no período de janeiro de 2000 a dezembro de 2003. Os dados foram tabulados através das informações colhidas dos prontuários dos pacientes, tais como: idade, gênero, tipo de fratura, e...

  2. The impact of resource loss on Holocaust survivors facing war and terrorism in Israel

    Science.gov (United States)

    Dekel, R.; Hobfoll, S. E.

    2009-01-01

    We examined the distress level of 102 Holocaust survivors in Israel during a recent period of continuous exposure of the Israeli population to terror and the threat of missile attack. Based on the Conservation of Resources (COR) theory, we explored the contribution of losses suffered during the Holocaust and of current loss of resources due to terror attacks on their distress level. Twenty one percent of the sample had probable PTSD and high psychological distress levels in general. Current loss of psychosocial resources contributed significantly to survivors’ current PTSD symptomatology and general psychological distress, above the contribution of the previous Holocaust-related loss. Our findings support COR theory, which states that traumatic events are associated with ongoing and often rapid loss of resources. Resource loss, in turn, is associated with higher distress levels. Moreover, current loss of resources compounds the impact of earlier resource losses incurred during the Holocaust. PMID:17453549

  3. Magnet pole tips

    Science.gov (United States)

    Thorn, Craig E.; Chasman, Chellis; Baltz, Anthony J.

    1984-04-24

    An improved magnet which more easily provides a radially increasing magnetic field, as well as reduced fringe field and requires less power for a given field intensity. The subject invention comprises a pair of spaced, opposed magnetic poles which further comprise a pair of pole roots, each having a pole tip attached to its center. The pole tips define the gap between the magnetic poles and at least a portion of each pole tip is separated from its associated pole root. The separation begins at a predetermined distance from the center of the pole root and increases with increasing radial distance while being constant with azimuth within that portion. Magnets in accordance with the subject invention have been found to be particularly advantageous for use in large isochronous cyclotrons.

  4. Poling of Planar Silica Waveguides

    DEFF Research Database (Denmark)

    Arentoft, Jesper; Kristensen, Martin; Jensen, Jesper Bo

    1999-01-01

    UV-written planar silica waveguides are poled using two different poling techniques, thermal poling and UV-poling. Thermal poling induces an electro-optic coefficient of 0.067 pm/V. We also demonstrate simultaneous UV-writing and UV-poling. The induced electro-optic effect shows a linear dependence...

  5. Mathematical Modeling for Risk Averse Firm Facing Loss Averse Customer’s Stochastic Uncertainty

    Directory of Open Access Journals (Sweden)

    Seungbeom Kim

    2017-01-01

    Full Text Available To optimize the firm’s profit during a finite planning horizon, a dynamic programming model is used to make joint pricing and inventory replenishment decision assuming that customers are loss averse and the firm is risk averse. We model the loss averse customer’s demand using the multinomial choice model. In this choice model, we consider the acquisition and transition utilities widely used by a mental accounting theory which also incorporate the reference price and actual price. Then, we show that there is an optimal inventory policy which is base-stock policy depending on the accumulated wealth in each period.

  6. Job Loss at Mid-Life: Managers and Executives Face the "New Risk Economy"

    Science.gov (United States)

    Mendenhall, Ruby; Kalil, Ariel; Spindel, Laurel J.; Hart, Cassandra M. D.

    2008-01-01

    We use a life course framework to examine how the "new risk economy" has left middle-age professionals, managers and executives more vulnerable to job loss and unemployment despite high levels of human capital. Using in-depth qualitative data from 77 recently-unemployed white-collar workers, we examine perceptions of macro-economic…

  7. Anxiety promotes memory for mood-congruent faces but does not alter loss aversion.

    Science.gov (United States)

    Charpentier, Caroline J; Hindocha, Chandni; Roiser, Jonathan P; Robinson, Oliver J

    2016-04-21

    Pathological anxiety is associated with disrupted cognitive processing, including working memory and decision-making. In healthy individuals, experimentally-induced state anxiety or high trait anxiety often results in the deployment of adaptive harm-avoidant behaviours. However, how these processes affect cognition is largely unknown. To investigate this question, we implemented a translational within-subjects anxiety induction, threat of shock, in healthy participants reporting a wide range of trait anxiety scores. Participants completed a gambling task, embedded within an emotional working memory task, with some blocks under unpredictable threat and others safe from shock. Relative to the safe condition, threat of shock improved recall of threat-congruent (fearful) face location, especially in highly trait anxious participants. This suggests that threat boosts working memory for mood-congruent stimuli in vulnerable individuals, mirroring memory biases in clinical anxiety. By contrast, Bayesian analysis indicated that gambling decisions were better explained by models that did not include threat or treat anxiety, suggesting that: (i) higher-level executive functions are robust to these anxiety manipulations; and (ii) decreased risk-taking may be specific to pathological anxiety. These findings provide insight into the complex interactions between trait anxiety, acute state anxiety and cognition, and may help understand the cognitive mechanisms underlying adaptive anxiety.

  8. Lower pole stones

    DEFF Research Database (Denmark)

    Sanguedolce, Francesco; Breda, Alberto; Millan, Felix

    2013-01-01

    PURPOSE: To assess efficacy and safety of prone- and supine percutaneous nephrolithotomy (PCNL) for the treatment of lower pole kidney stones. METHODS: Data from patients affected by lower pole kidney stones and treated with PCNL between December 2005 and August 2010 were collected retrospectively...... by seven referral centres. Variables analysed included patient demographics, clinical and surgical characteristics, stone-free rates (SFR) and complications. Statistical analysis was conducted to compare the differences for SFRs and complication rates between prone- and supine PCNL. RESULTS: One hundred...... seventeen patients underwent PCNL (mean stone size: 19.5 mm) for stones harboured only in the lower renal pole (single stone: 53.6 %; multiple stones: 46.4 %). A higher proportion of patients with ASA score ≥ 3 and harbouring multiple lower pole stones were treated with supine PCNL (5.8 vs. 23.1 %; p = 0...

  9. Long-term neuroplasticity of the face primary motor cortex and adjacent somatosensory cortex induced by tooth loss can be reversed following dental implant replacement in rats.

    Science.gov (United States)

    Avivi-Arber, Limor; Lee, Jye-Chang; Sood, Mandeep; Lakschevitz, Flavia; Fung, Michelle; Barashi-Gozal, Maayan; Glogauer, Michael; Sessle, Barry J

    2015-11-01

    Tooth loss is common, and exploring the neuroplastic capacity of the face primary motor cortex (face-M1) and adjacent primary somatosensory cortex (face-S1) is crucial for understanding how subjects adapt to tooth loss and their prosthetic replacement. The aim was to test if functional reorganization of jaw and tongue motor representations in the rat face-M1 and face-S1 occurs following tooth extraction, and if subsequent dental implant placement can reverse this neuroplasticity. Rats (n = 22) had the right maxillary molar teeth extracted under local and general anesthesia. One month later, seven rats had dental implant placement into healed extraction sites. Naive rats (n = 8) received no surgical treatment. Intracortical microstimulation (ICMS) and recording of evoked jaw and tongue electromyographic responses were used to define jaw and tongue motor representations at 1 month (n = 8) or 2 months (n = 7) postextraction, 1 month postimplant placement, and at 1-2 months in naive rats. There were no significant differences across study groups in the onset latencies of the ICMS-evoked responses (P > 0.05), but in comparison with naive rats, tooth extraction caused a significant (P tooth loss and their replacement with dental implants. © 2015 Wiley Periodicals, Inc.

  10. Seeing the Talker's Face Improves Free Recall of Speech for Young Adults With Normal Hearing but Not Older Adults With Hearing Loss.

    Science.gov (United States)

    Rudner, Mary; Mishra, Sushmit; Stenfelt, Stefan; Lunner, Thomas; Rönnberg, Jerker

    2016-06-01

    Seeing the talker's face improves speech understanding in noise, possibly releasing resources for cognitive processing. We investigated whether it improves free recall of spoken two-digit numbers. Twenty younger adults with normal hearing and 24 older adults with hearing loss listened to and subsequently recalled lists of 13 two-digit numbers, with alternating male and female talkers. Lists were presented in quiet as well as in stationary and speech-like noise at a signal-to-noise ratio giving approximately 90% intelligibility. Amplification compensated for loss of audibility. Seeing the talker's face improved free recall performance for the younger but not the older group. Poorer performance in background noise was contingent on individual differences in working memory capacity. The effect of seeing the talker's face did not differ in quiet and noise. We have argued that the absence of an effect of seeing the talker's face for older adults with hearing loss may be due to modulation of audiovisual integration mechanisms caused by an interaction between task demands and participant characteristics. In particular, we suggest that executive task demands and interindividual executive skills may play a key role in determining the benefit of seeing the talker's face during a speech-based cognitive task.

  11. Seeing the Talker's Face Improves Free Recall of Speech for Young Adults with Normal Hearing but Not Older Adults with Hearing Loss

    Science.gov (United States)

    Rudner, Mary; Mishra, Sushmit; Stenfelt, Stefan; Lunner, Thomas; Rönnberg, Jerker

    2016-01-01

    Purpose: Seeing the talker's face improves speech understanding in noise, possibly releasing resources for cognitive processing. We investigated whether it improves free recall of spoken two-digit numbers. Method: Twenty younger adults with normal hearing and 24 older adults with hearing loss listened to and subsequently recalled lists of 13…

  12. Two-step calibration method for multi-algorithm score-based face recognition systems by minimizing discrimination loss

    NARCIS (Netherlands)

    Susyanto, N.; Veldhuis, Raymond N.J.; Spreeuwers, Lieuwe Jan; Klaassen, C.A.J.

    2016-01-01

    We propose a new method for combining multi-algorithm score-based face recognition systems, which we call the two-step calibration method. Typically, algorithms for face recognition systems produce dependent scores. The two-step method is based on parametric copulas to handle this dependence. Its

  13. Wood pole overhead lines

    CERN Document Server

    Wareing, Brian

    2005-01-01

    This new book concentrates on the mechanical aspects of distribution wood pole lines, including live line working, environmental influences, climate change and international standards. Other topics include statutory requirements, safety, profiling, traditional and probabilistic design, weather loads, bare and covered conductors, different types of overhead systems, conductor choice, construction and maintenance. A section has also been devoted to the topic of lightning, which is one of the major sources of faults on overhead lines. The book focuses on the effects of this problem and the strate

  14. The South Pole Telescope

    Energy Technology Data Exchange (ETDEWEB)

    Ruhl, J.E.; Ade, P.A.R.; Carlstrom, J.E.; Cho, H.M.; Crawford,T.; Dobbs, M.; Greer, C.H.; Halverson, N.W.; Holzapfel, W.L.; Lanting,T.M.; Lee, A.T.; Leitch, E.M.; Leong, J.; Lu, W.; Lueker, M.; Mehl, J.; Meyer, S.S.; Mohr, J.J.; Padin, S.; Plagge, T.; Pryke, C.; Runyan, M.C.; Schwan, D.; Sharp, M.K.; Spieler, H.; Staniszewski, Z.; Stark, A.A.

    2004-11-04

    A new 10 meter diameter telescope is being constructed for deployment at the NSF South Pole research station. The telescope is designed for conducting large-area millimeter and sub-millimeter wave surveys of faint, low contrast emission, as required to map primary and secondary anisotropies in the cosmic microwave background. To achieve the required sensitivity and resolution, the telescope design employs an off-axis primary with a 10 m diameter clear aperture. The full aperture and the associated optics will have a combined surface accuracy of better than 20 microns rms to allow precision operation in the submillimeter atmospheric windows. The telescope will be surrounded with a large reflecting ground screen to reduce sensitivity to thermal emission from the ground and local interference. The optics of the telescope will support a square degree field of view at 2mm wavelength and will feed a new 1000-element micro-lithographed planar bolometric array with superconducting transition-edge sensors and frequency-multiplexed readouts. The first key project will be to conduct a survey over 4000 degrees for galaxy clusters using the Sunyaev-Zeldovich Effect. This survey should find many thousands of clusters with a mass selection criteria that is remarkably uniform with redshift. Armed with redshifts obtained from optical and infrared follow-up observations, it is expected that the survey will enable significant constraints to be placed on the equation of state of the dark energy.

  15. Glass Waveguides for Periodic Poling

    DEFF Research Database (Denmark)

    Fage-Pedersen, Jacob; Jacobsen, Rune Shim; Kristensen, Martin

    2005-01-01

    Planar silica-based waveguide devices have been developed for second-harmonic generation by poling with periodic electrodes. We show that detrimental charge transport can occur along interfaces, but with proper choice of fabrication, high-quality devices are obtained.......Planar silica-based waveguide devices have been developed for second-harmonic generation by poling with periodic electrodes. We show that detrimental charge transport can occur along interfaces, but with proper choice of fabrication, high-quality devices are obtained....

  16. Glass Waveguides for Periodic Poling

    DEFF Research Database (Denmark)

    Fage-Pedersen, Jacob; Jacobsen, Rune Shim; Kristensen, Martin

    2005-01-01

    Planar silica-based waveguide devices have been developed for second-harmonic generation by poling with periodic electrodes. We show that detrimental charge transport can occur along interfaces, but with proper choice of fabrication, high-quality devices are obtained....

  17. Face to Face

    Indian Academy of Sciences (India)

    Home; Journals; Resonance – Journal of Science Education; Volume 14; Issue 10. Turning a New Leaf H. Y. Mohan Ram talks to Sujata Varadarajan. H Y Mohan Ram Sujata Varadarajan. Face to Face Volume 14 Issue 10 October 2009 pp 1003-1017 ...

  18. Face to Face

    Indian Academy of Sciences (India)

    Home; Journals; Resonance – Journal of Science Education; Volume 20; Issue 3. Symmetry and Mathematics: Pioneering Insights into the Structure of Physics. Urjit A Yajnik. Face to Face Volume 20 Issue 3 March 2015 pp 264-276. Fulltext. Click here to view fulltext PDF. Permanent link:

  19. Face to Face

    DEFF Research Database (Denmark)

    Jungfalk, Michael; Rossen, Svend

    2008-01-01

    Blended learning in education is the combination of face‐to‐face seminars and on‐line work based on the internet. We have investigated which factors that we found were important in designing and conducting face‐to‐face seminars in order to facilitate learning processes in the periods of on...

  20. Face to Face

    Indian Academy of Sciences (India)

    Home; Journals; Resonance – Journal of Science Education; Volume 16; Issue 1. Do We Learn to See? Torsten Wiesel Prasanna Venkhatesh Venkataramani. Face to Face Volume 16 Issue 1 January 2011 pp 88-99. Fulltext. Click here to view fulltext PDF. Permanent link:

  1. Face to Face

    Indian Academy of Sciences (India)

    Home; Journals; Resonance – Journal of Science Education; Volume 19; Issue 5. Science is Not a Zero-Sum Game. Devendra Mani. Face to Face Volume 19 Issue 5 May 2014 pp 471-477. Fulltext. Click here to view fulltext PDF. Permanent link: https://www.ias.ac.in/article/fulltext/reso/019/05/0471-0477. Author Affiliations.

  2. 47 CFR 32.6411 - Poles expense.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 2 2010-10-01 2010-10-01 false Poles expense. 32.6411 Section 32.6411... FOR TELECOMMUNICATIONS COMPANIES Instructions for Expense Accounts § 32.6411 Poles expense. This account shall include expenses associated with poles. ...

  3. REGION NORTH OF TEACHER EDUCATION POLICY AND EVALUATION OF POLES OPEN UNIVERSITY SYSTEM OF BRAZIL

    Directory of Open Access Journals (Sweden)

    Celso José da Costa

    2013-03-01

    Full Text Available This text aims to present, in general, the north region and policies for teacher training implemented in the last 5 years, locating in this context the importance of the Brazil Open University system and its supporting poles face as methodology research linked to the project "Institutionalization of Distance Education in Brazil." Greater emphasis will be given to data from the states of Pará and Acre, given that two authors of this text act as coordinators of the poles supporting attendance System Open University of Brazil in these states. We design the text, based on testimony of poles coordinators who participated in participatory research, conducted by the Research Group "Teacher education and information and communication technologies", LANTE / UFF. We aim also to identify the structure and functioning of the Poles face Supporting UAB in the North as well as the assessment tool applied in this region.

  4. Pole counting and resonance classification

    International Nuclear Information System (INIS)

    Morgan, D.

    1992-01-01

    S-wave resonances occurring close to an inelastic threshold can be classified according to the number of nearby poles they possess. One then has a useful possibility of distinguishing dynamical alternatives by objective appeal to data. Making this quantitative entails developing suitable effective range expansions for various realizations of potential scattering. A key application is deciding the make-up of f 0 (976) (S*). (author)

  5. Method and apparatus for assembling a permanent magnet pole assembly

    Science.gov (United States)

    Carl, Jr., Ralph James; Bagepalli, Bharat Sampathkumaran [Niskayuna, NY; Jansen, Patrick Lee [Scotia, NY; Dawson, Richard Nils [Voorheesville, NY; Qu, Ronghai [Clifton Park, NY; Avanesov, Mikhail Avramovich [Moscow, RU

    2009-08-11

    A pole assembly for a rotor, the pole assembly includes a permanent magnet pole including at least one permanent magnet block, a plurality of laminations including a pole cap mechanically coupled to the pole, and a plurality of laminations including a base plate mechanically coupled to the pole.

  6. Evaluation of magnetic field distribution of superconducting bulk magnets with the same pole arrangement

    International Nuclear Information System (INIS)

    Yokoyama, K.; Oka, T.; Noto, K.

    2008-01-01

    We study on the construction of superconducting permanent magnets by RE123 bulk materials and the investigation of these industrial applications such as a magnetic separation. The bulk magnets can generate strong magnetic field in comparison with common permanent magnets and iron-cored electromagnets. In order to propagate an industrial application of bulk magnet in the feature, it is necessary to form various shape of magnetic field, as well as its strength is enlarged. In this paper, the strong magnetic field in the radial direction has been constructed by a pair of bulk magnets. Two Gd123 bulk materials are magnetized by the IMRA method and these are arranged face-to-face with the same pole facing each other. When the radial component of magnetic fields, B x , is measured in the open space between the magnetic poles with a gap of 50 mm, the area of |B x | > 0.5 T increases to 148% compared with the single pole

  7. Macro Fiber Piezocomposite Actuator Poling Study

    Science.gov (United States)

    Werlink, Rudy J.; Bryant, Robert G.; Manos, Dennis

    2002-01-01

    The performance and advantages of Piezocomposite Actuators are to provide a low cost, in-situ actuator/sensor that is flexible, low profile and high strain per volt performance in the same plane of poled voltage. This paper extends reported data for the performance of these Macrofiber Composite (MFC) Actuators to include 4 progressively narrower Intedigitized electrode configurations with several line widths and spacing ratios. Data is reported for max free strain, average strain per applied volt, poling (alignment of the electric dipoles of the PZT ceramic) voltage vs. strain and capacitance, time to poling voltage 95% saturation. The output strain per volt progressively increases as electrode spacing decreases, with saturation occurring at lower poling voltages. The narrowest spacing ratio becomes prone to voltage breakdown or short circuits limiting the spacing width with current fabrication methods. The capacitance generally increases with increasing poling voltage level but has high sensitivity to factors such as temperature, moisture and time from poling which limit its usefulness as a simple indicator. The total time of applied poling voltage to saturate or fully line up the dipoles in the piezoceramic was generally on the order of 5-20 seconds. Less sensitivity to poling due to the applied rate of voltage increase over a 25 to 500 volt/second rate range was observed.

  8. Strength of single-pole utility structures

    Science.gov (United States)

    Ronald W. Wolfe

    2006-01-01

    This section presents three basic methods for deriving and documenting Rn as an LTL value along with the coefficient of variation (COVR) for single-pole structures. These include the following: 1. An empirical analysis based primarily on tests of full-sized poles. 2. A theoretical analysis of mechanics-based models used in...

  9. Planar glass devices for efficient periodic poling

    DEFF Research Database (Denmark)

    Fage-Pedersen, Jacob; Jacobsen, Rune Shim; Kristensen, Martin

    2005-01-01

    We demonstrate that frequency-converting devices of high quality can be realised with glass poling. The devices, made with silica-on-silicon technology, are poled with periodic, embedded electrodes, and used for second-harmonic generation. We obtain precise control of the quasi phase-matching wav......We demonstrate that frequency-converting devices of high quality can be realised with glass poling. The devices, made with silica-on-silicon technology, are poled with periodic, embedded electrodes, and used for second-harmonic generation. We obtain precise control of the quasi phase......-matching wavelength and bandwidth, and a normalised conversion efficiency of 1.4×10-3 %/W/cm2 which, to our knowledge, is the highest obtained so far with periodic glass poling....

  10. Metrópoles desgovernadas

    Directory of Open Access Journals (Sweden)

    Erminia Maricato

    2011-04-01

    Full Text Available Apesar de sua importância econômica, política, social, demográfica, cultural, territorial e ambiental, há, nas metrópoles brasileiras, uma significativa falta de governo, evidenciada pelas incipientes iniciativas de cooperação administrativa intermunicipal e federativa. Este artigo aborda as mudanças estruturais - no processo de urbanização/ metropolização - devidas à reestruturação produtiva do capitalismo global, e, na escala nacional, trata da mudança no marco institucional - jurídico/político - que passou de concentrador e centralizador, durante o regime militar, para descentralizador e esvaziado, após a Constituição de 1988. O recuo verificado nas políticas sociais durante os anos 1980 e 1990, notadamente em transporte, habitação e saneamento, além do desmonte dos organismos metropolitanos, conduziu nossas metrópoles a um destino de banalização das tragédias urbanas. Em que pese sua urgência, a questão metropolitana não sensibiliza nenhuma força política ou instituição que lhe atribua lugar de destaque na agenda nacional.Despite its economic, political, social, demographic, cultural, territorial and environmental importance, there is a significant lack of government in the brazilian metropolises, evidenced by the incipient initiatives of intermunicipal and federative administrative cooperation. This article analyses the structural changes - in the process of urbanization/metropolization - due to the productive restructuring of global capitalism, and, in a national scale, analyses the change in the institutional mark - legal/political - which passed from concentrator and centralizer, during the Military Regimen, to decentralized and emptied, after 1988 Constitution. The downturn verified in social policies during the years 1980 and 1990, notably in transport, housing and sanitation, besides the dismantling of the metropolitan agencies, has led our cities to the trivialization of urban tragedies. Despite

  11. Requirements for NuMA in maintenance and establishment of mammalian spindle poles.

    Science.gov (United States)

    Silk, Alain D; Holland, Andrew J; Cleveland, Don W

    2009-03-09

    Microtubules of the mitotic spindle in mammalian somatic cells are focused at spindle poles, a process thought to include direct capture by astral microtubules of kinetochores and/or noncentrosomally nucleated microtubule bundles. By construction and analysis of a conditional loss of mitotic function allele of the nuclear mitotic apparatus (NuMA) protein in mice and cultured primary cells, we demonstrate that NuMA is an essential mitotic component with distinct contributions to the establishment and maintenance of focused spindle poles. When mitotic NuMA function is disrupted, centrosomes provide initial focusing activity, but continued centrosome attachment to spindle fibers under tension is defective, and the maintenance of focused kinetochore fibers at spindle poles throughout mitosis is prevented. Without centrosomes and NuMA, initial establishment of spindle microtubule focusing completely fails. Thus, NuMA is a defining feature of the mammalian spindle pole and functions as an essential tether linking bulk microtubules of the spindle to centrosomes.

  12. Performance analysis of variable speed multiphase induction motor with pole phase modulation

    Directory of Open Access Journals (Sweden)

    Liu Huijuan

    2016-09-01

    Full Text Available The pole phase modulation (PPM technique is an effective method to extend speed range and torque capabilities for an integrated starter and hybrid electric vehicles applications. In this paper, the five pole-phase combination types of a multiphase induction motor (IM with 36 stator slots and 36 stator conductors are presented and compared quantitatively by using the time-stepping finite element method (TS-FEM. The 36 stator conductors of the proposed multiphase IM are fed by a 36 leg inverter and the current phase angle and amplitude of each stator conductor can be controlled independently. This paper focuses on the winding connection, the PPM technique and the performance comparative analysis of each pole-phase combination types of the proposed multiphase IM. The flux distribution, air-gap flux density, output torque, core losses and efficiency of five pole-phase combination types have been investigated.

  13. Holography with a Landau pole

    Science.gov (United States)

    Faedo, Antón F.; Mateos, David; Pantelidou, Christiana; Tarrío, Javier

    2017-02-01

    Holography for UV-incomplete gauge theories is important but poorly understood. A paradigmatic example is d = 4, N=4 super Yang-Mills coupled to N f quark flavors, which possesses a Landau pole at a UV scale ΛLP. The dual gravity solution exhibits a UV singularity at a finite proper distance along the holographic direction. Despite this, holographic renormalization can be fully implemented via analytic continuation to an AdS solution. The presence of a UV cut-off manifests itself in several interesting ways. At energies E ≪ ΛLP no pathologies appear, as expected from effective field theory. In contrast, at scales E ≲ ΛLP the gravitational potential becomes repulsive, and at temperatures T ≲ ΛLP the specific heat becomes negative. Although we focus on N=4 super Yang-Mills with flavor, our qualitative results apply to a much more general class of theories, since they only depend on the fact that the metric near the UV singularity is a hyper-scaling violating metric with exponent θ > d - 1.

  14. Holography with a Landau pole

    Energy Technology Data Exchange (ETDEWEB)

    Faedo, Antón F. [Departament de Física Quántica i Astrofísica and Institut de Ciències del Cosmos (ICC), Universitat de Barcelona, Martí i Franquès 1, ES-08028, Barcelona (Spain); Mateos, David [Departament de Física Quántica i Astrofísica and Institut de Ciències del Cosmos (ICC), Universitat de Barcelona, Martí i Franquès 1, ES-08028, Barcelona (Spain); Institució Catalana de Recerca i Estudis Avançats (ICREA), Passeig Lluís Companys 23, ES-08010, Barcelona (Spain); Pantelidou, Christiana [Departament de Física Quántica i Astrofísica and Institut de Ciències del Cosmos (ICC), Universitat de Barcelona, Martí i Franquès 1, ES-08028, Barcelona (Spain); Tarrío, Javier [Physique Théorique et Mathématique, Université Libre de Bruxelles (ULB), and International Solvay Institutes, Campus de la Plaine CP 231, B-1050, Brussels (Belgium)

    2017-02-08

    Holography for UV-incomplete gauge theories is important but poorly understood. A paradigmatic example is d=4, N=4 super Yang-Mills coupled to N{sub f} quark flavors, which possesses a Landau pole at a UV scale Λ{sub LP}. The dual gravity solution exhibits a UV singularity at a finite proper distance along the holographic direction. Despite this, holographic renormalization can be fully implemented via analytic continuation to an AdS solution. The presence of a UV cut-off manifests itself in several interesting ways. At energies E≪Λ{sub LP} no pathologies appear, as expected from effective field theory. In contrast, at scales E≲Λ{sub LP} the gravitational potential becomes repulsive, and at temperatures T≲Λ{sub LP} the specific heat becomes negative. Although we focus on N=4 super Yang-Mills with flavor, our qualitative results apply to a much more general class of theories, since they only depend on the fact that the metric near the UV singularity is a hyper-scaling violating metric with exponent θ>d−1.

  15. Geometric Modelling of Octagonal Lamp Poles

    Science.gov (United States)

    Chan, T. O.; Lichti, D. D.

    2014-06-01

    Lamp poles are one of the most abundant highway and community components in modern cities. Their supporting parts are primarily tapered octagonal cones specifically designed for wind resistance. The geometry and the positions of the lamp poles are important information for various applications. For example, they are important to monitoring deformation of aged lamp poles, maintaining an efficient highway GIS system, and also facilitating possible feature-based calibration of mobile LiDAR systems. In this paper, we present a novel geometric model for octagonal lamp poles. The model consists of seven parameters in which a rotation about the z-axis is included, and points are constrained by the trigonometric property of 2D octagons after applying the rotations. For the geometric fitting of the lamp pole point cloud captured by a terrestrial LiDAR, accurate initial parameter values are essential. They can be estimated by first fitting the points to a circular cone model and this is followed by some basic point cloud processing techniques. The model was verified by fitting both simulated and real data. The real data includes several lamp pole point clouds captured by: (1) Faro Focus 3D and (2) Velodyne HDL-32E. The fitting results using the proposed model are promising, and up to 2.9 mm improvement in fitting accuracy was realized for the real lamp pole point clouds compared to using the conventional circular cone model. The overall result suggests that the proposed model is appropriate and rigorous.

  16. Tree-loop duality relation beyond single poles

    International Nuclear Information System (INIS)

    Bierenbaum, Isabella; Buchta, Sebastian; Draggiotis, Petros; Malamos, Ioannis; Rodrigo, German

    2012-11-01

    We develop the Tree-Loop Duality Relation for two- and three-loop integrals with multiple identical propagators (multiple poles). This is the extension of the Duality Relation for single poles and multi-loop integrals derived in previous publications. We prove a generalization of the formula for single poles to multiple poles and we develop a strategy for dealing with higher-order pole integrals by reducing them to single pole integrals using Integration By Parts.

  17. A Comparative Analysis of the New Five-Pole and Three-Pole Active Magnet Bearing

    Directory of Open Access Journals (Sweden)

    Pedram Vakili

    2012-07-01

    Full Text Available In recent years, more attention has been given to the active AMBs thanks to their low maintenance cost, suitability for clean environments, and high speed. One of the popular types of AMBs is the three-pole type with integrated and separate cores. Some deficiencies of this type of bearing are its high oscillation, low stability and low efficiency. This paper seeks to analyse the three-pole AMBs and describe their deficiencies and introduce and analyse a new five-pole AMB. The model thus proposed has lower oscillation as well as more stability and efficiency. The five-pole AMB has been simulated by a controller in the presence of disturbance. The results of simulation demonstrate lower vibration and oscillation in the five-pole AMB in comparison with the three-pole model.

  18. On pole structure assignment in linear systems

    Czech Academy of Sciences Publication Activity Database

    Loiseau, J.-J.; Zagalak, Petr

    2009-01-01

    Roč. 82, č. 7 (2009), s. 1179-1192 ISSN 0020-7179 R&D Projects: GA ČR(CZ) GA102/07/1596 Institutional research plan: CEZ:AV0Z10750506 Keywords : linear systems * linear state feedback * pole structure assignment Subject RIV: BC - Control Systems Theory Impact factor: 1.124, year: 2009 http://library.utia.cas.cz/separaty/2009/AS/zagalak-on pole structure assignment in linear systems.pdf

  19. Quantified Faces

    DEFF Research Database (Denmark)

    Sørensen, Mette-Marie Zacher

    2016-01-01

    Abstract: The article presents three contemporary art projects that, in various ways, thematise questions regarding numerical representation of the human face in relation to the identification of faces, for example through the use of biometric video analysis software, or DNA technology. The Dutch...... artist Marnix de Nijs' Physiognomic Scrutinizer is an interactive installation whereby the viewer's face is scanned and identified with historical figures. The American artist Zach Blas' project Fag Face Mask consists of three-dimensional portraits that blend biometric facial data from 30 gay men's faces...

  20. Clouds Over the North Pole

    Science.gov (United States)

    2004-01-01

    [figure removed for brevity, see original site] Released 29 June 2004 The atmosphere of Mars is a dynamic system. Water-ice clouds, fog, and hazes can make imaging the surface from space difficult. Dust storms can grow from local disturbances to global sizes, through which imaging is impossible. Seasonal temperature changes are the usual drivers in cloud and dust storm development and growth. Eons of atmospheric dust storm activity has left its mark on the surface of Mars. Dust carried aloft by the wind has settled out on every available surface; sand dunes have been created and moved by centuries of wind; and the effect of continual sand-blasting has modified many regions of Mars, creating yardangs and other unusual surface forms. Like yesterday's image, the linear 'ripples' are water-ice clouds. As spring is deepening at the North Pole these clouds are becoming more prevalent. Image information: VIS instrument. Latitude 68.9, Longitude 135.5 East (224.5 West). 38 meter/pixel resolution. Note: this THEMIS visual image has not been radiometrically nor geometrically calibrated for this preliminary release. An empirical correction has been performed to remove instrumental effects. A linear shift has been applied in the cross-track and down-track direction to approximate spacecraft and planetary motion. Fully calibrated and geometrically projected images will be released through the Planetary Data System in accordance with Project policies at a later time. NASA's Jet Propulsion Laboratory manages the 2001 Mars Odyssey mission for NASA's Office of Space Science, Washington, D.C. The Thermal Emission Imaging System (THEMIS) was developed by Arizona State University, Tempe, in collaboration with Raytheon Santa Barbara Remote Sensing. The THEMIS investigation is led by Dr. Philip Christensen at Arizona State University. Lockheed Martin Astronautics, Denver, is the prime contractor for the Odyssey project, and developed and built the orbiter. Mission operations are

  1. Performance evaluation of a five-phase modular external rotor PM machine with different rotor poles

    Directory of Open Access Journals (Sweden)

    A.S. Abdel-Khalik

    2012-12-01

    Full Text Available The performance of fault-tolerant modular permanent magnet (PM machines depends on the proper selection of the pole and slot numbers which result in negligible coupling between phases. The preferred slot and pole number combinations eliminate the effect of low order harmonics in the stator magneto motive force and thereby the vibration and stray loss are reduced. In this paper, three external rotor machines with identical machine dimensions are designed with different slots per phase per pole (SPP ratios. A simulation study is carried out using finite element analysis to compare the performance of the three machines in terms of machine torque density, ripple torque, core loss, and machine efficiency. A mathematical model based on the conventional phase model approach is also used for the comparative study. The simulation study is extended to depict machine performance under fault conditions.

  2. Five-Phase Modular External Rotor PM Machines with Different Rotor Poles: A Comparative Simulation Study

    Directory of Open Access Journals (Sweden)

    A. S. Abdel-Khalik

    2012-01-01

    Full Text Available The performance of fault-tolerant modular permanent magnet machines depends on the proper selection of the pole and slot numbers which result in negligible coupling between phases. The preferred slot and pole number combinations eliminate the effect of low-order harmonics in the stator magnetomotive force and thereby the vibration and stray loss are reduced. In this paper, three external rotor machines with identical machine dimensions are designed with different slots per phase per pole ratios. A simulation study is carried out using finite element analysis to compare the performance of the three machines in terms of machine torque density, ripple torque, core loss, and machine efficiency. A mathematical model based on the conventional-phase-model approach is also used for the comparative study. The simulation study is extended to depict machine performance under fault conditions.

  3. The potential of wood-based composite poles

    Science.gov (United States)

    Todd F. Shupe; Cheng Piao; Chung Y. Hse

    2009-01-01

    Wood-based composite utility poles are receiving increasing attention in the North American pole market. This interest is being driven by many increasing factors such as increasing: (1) disposal costs of solid wood poles, (2) liability and environmental concerns with traditional means of disposal of solid wood poles, (3) cost and concerns of long-term...

  4. Mechanical properties of small-scale wood laminated composite poles

    Science.gov (United States)

    Cheng Piao; Todd F. Shupe; Chung Y. Hse

    2004-01-01

    Power companies in the United States consume millions of solid wood poles every year. These poles are from high-valued trees that are becoming more expensive and less available. wood laminated composite poles (LCP) are a novel alternative to solid wood poles. LCP consists of trapezoid wood strips that are bonded by a synthetic resin. The wood strips can be made from...

  5. 2D Stabilised analytic signal method in DC pole-pole potential data ...

    Indian Academy of Sciences (India)

    R. Narasimhan (Krishtel eMaging) 1461 1996 Oct 15 13:05:22

    Using analytic signal method, interpretation of pole-pole secondary electric potentials due to 2D conductive/resistive prisms is presented. ... residual separation to separate out residual anom- alies, which are interpreted for geological .... terms, which are used for the semi-quantitative interpretation. 6.1 Computation of ...

  6. An unusual complication of ischemic injury to upper pole ureter during lower pole heminephroureterectomy

    Directory of Open Access Journals (Sweden)

    Katherine Victoria Hurst

    2013-01-01

    Full Text Available Lower pole heminephroureterectomy is a common paediatric urology procedure with few reported complications. We report a case of possible vascular ischemic injury to the normal remaining ureter following a lower pole heminephroureterectomy, probably due to both ureters sharing a common blood supply. Extra caution in such procedures is therefore warranted.

  7. Jupiter's interior and deep atmosphere: The initial pole-to-pole passes with the Juno spacecraft

    DEFF Research Database (Denmark)

    Bolton, S. J.; Adriani, Alberto; Adumitroaie, V.

    2017-01-01

    On 27 August 2016, the Juno spacecraft acquired science observations of Jupiter, passing less than 5000 kilometers above the equatorial cloud tops. Images of Jupiter's poles show a chaotic scene, unlike Saturn's poles. Microwave sounding reveals weather features at pressures deeper than 100 bars,...

  8. 2D Stabilised analytic signal method in DC pole-pole potential data ...

    Indian Academy of Sciences (India)

    R. Narasimhan (Krishtel eMaging) 1461 1996 Oct 15 13:05:22

    Using analytic signal method, interpretation of pole-pole secondary electric potentials due to 2D conductive/resistive prisms is presented. The estimated parameters are the location, lateral extent or width and depth to top surface of the prism. Forward modelling is attempted by 2D-Finite. Difference method. The proposed ...

  9. Effect of changing the pole profile in a gradient septum magnet

    International Nuclear Information System (INIS)

    Armstrong, A.G.A.M.

    1977-05-01

    A tapered-pole gradient septum magnet was fitted with wedge-shaped shims to make the gap parallel. The resulting field was measured and compared with the predicted field from the GFUN magnetostatic computer program. A method of estimating the beam loss due to kick non-uniformity is presented. (author)

  10. About Face

    Medline Plus

    Full Text Available ... Type Search All Videos PTSD Basics PTSD Treatment What is AboutFace? Resources for Professionals Get Help Home ... All Videos Learn More PTSD Basics PTSD Treatment What is AboutFace? Resources for Professionals Get Help PTSD ...

  11. New magnet pole shape for isochronous cyclotrons

    International Nuclear Information System (INIS)

    Thorn, C.E.; Chasman, C.; Baltz, A.J.

    1981-01-01

    A new design has been developed for shaping pole tips to produce the radially increasing fields required for isochronous cyclotrons. The conventional solid hill poles are replaced by poles mounted over a small secondary gap which tapers radially from maximum at the magnet edge to zero near the center. Field measurements with a model magnet and calculations with the code TRIM show an increase in field at the edge of the magnet without the usual corresponding large increase in fringing, and a radial field shape more nearly field independent than for conventional hills. The flying hills have several advantages for variable energy multiparticle cyclotrons: (1) a large reduction in the power dissipated by isochronizing trim coils; (2) a more constant shape and magnitude flutter factor, eliminating flutter coils and increasing the operating range; and (3) a sharper fall-off of the fringe field, simplifying beam extraction

  12. Pole solutions for flame front propagation

    CERN Document Server

    Kupervasser, Oleg

    2015-01-01

    This book deals with solving mathematically the unsteady flame propagation equations. New original mathematical methods for solving complex non-linear equations and investigating their properties are presented. Pole solutions for flame front propagation are developed. Premixed flames and filtration combustion have remarkable properties: the complex nonlinear integro-differential equations for these problems have exact analytical solutions described by the motion of poles in a complex plane. Instead of complex equations, a finite set of ordinary differential equations is applied. These solutions help to investigate analytically and numerically properties of the flame front propagation equations.

  13. Fundamental pole parameters of the N(1470)

    CERN Document Server

    Lee, P S

    1973-01-01

    The position and residue of the S-matrix pole of the Delta (1236) have been shown to be unique and independent of the particular resonance formula used, thus resolving a discrepancy among phenomenological fits. Unlike the P/sub 33/ partial wave, the P/sub 11/ resonance is highly inelastic, very broad, and has a large background. This produces huge uncertainties in its mass and width, depending on the parametrization used. It is reported that the position of the N(1470) pole is uniquely determined, 1380-110i MeV, from fits to the CERN phase shifts. (10 refs).

  14. Modeling the starting performance of high power solid rotor salient pole synchronous motors

    Energy Technology Data Exchange (ETDEWEB)

    Carlson, R.; Sadowski, N. [GRUCAD/Federal University of Santa Catarina, Florianopolis, SC 88040-970 (Brazil); Grander, L.O. [ELETROSUL Power Stations S.A., Florianopolis, SC 88040-901 (Brazil); Ruencos, F.; Ogawa, C.; Fo, F.J. Doubrawa [WEG Energy, Jaragua do Sul, SC 89256-900 (Brazil)

    2009-12-15

    A computer model, including analytical and FEM formulations, was developed to calculate the starting performance of synchronous motors with solid rotor salient poles. Using quasi-steady state equations, the average and the envelope of the oscillating electromagnetic torque as well as the stator rms current are calculated. With the stator current, the rotor pole losses are evaluated by FEM. The complete simulation process is performed by self-contained software composed by several computational modules properly tiled to simplify the work of a design engineer. The calculated starting performance was compared to experimental results showing satisfactory consistency. (author)

  15. Reading faces and Facing words

    DEFF Research Database (Denmark)

    Robotham, Julia Emma; Lindegaard, Martin Weis; Delfi, Tzvetelina Shentova

    perception of faces and words is affected by unilateral posterior stroke. Two patients with lesions in their dominant hemisphere and two with lesions in their non-dominant hemisphere were tested on sensitive tests of face and word perception during the stable phase of recovery. Despite all patients having...... unilateral lesions, we found no patient with a selective deficit in either reading or face processing. Rather, the patients showing a deficit in processing either words or faces were also impaired with the other category. One patient performed within the normal range on all tasks. In addition, all patients...... performed within normal range on at least one test of visual categorisation, strongly suggesting that their abnormal performance with words and faces does not represent a generalised visuo-perceptual deficit. Our results suggest that posterior areas in both hemispheres may be critical for both reading...

  16. About Face

    Medline Plus

    Full Text Available ... by Topic Videos by Type Search All Videos Learn More PTSD Basics PTSD Treatment What is AboutFace? ... types of therapy that are proven to work. Learn more about Prolonged Exposure (PE) and Cognitive Processing ...

  17. About Face

    Medline Plus

    Full Text Available Skip to Content Menu Closed (Tap to Open) Home Videos by Topic Videos by Type Search All ... What is AboutFace? Resources for Professionals Get Help Home Watch Videos by Topic Videos by Type Search ...

  18. Rotor pole refurbishment for hydrogenerators: insulation problems and solutions

    International Nuclear Information System (INIS)

    Reynolds, R.R.; Rux, L.

    2005-01-01

    Rotor poles for Unit 1 at Lower Granite Powerhouse were removed from the rotor and shipped to a repair facility for refurbishment. Upon inspection, it was found that all of the pole bodies exhibited a distinct bow, center to end, on the pole mounting surface. In some cases, the deflection was as much as 0.106 inch. Concerns were raised about how this condition might affect the ability to properly insulate and/or re-seat the poles. This paper presents details of the rotor pole and field winding evaluation, the problems encountered, and the solutions implemented to successfully refurbish the rotor poles and field winding. (author)

  19. Recent advances in poled optical fibres

    DEFF Research Database (Denmark)

    Pruneri, V.; Margulis, W.; Myrén, N.

    2005-01-01

    A second-order nonlinearity can be induced in optical fibres through poling. We describe accomplishments of the EU project GLAMOROUS in making low-cost high performance electrooptic and nonlinear optical fibre- and waveguide-based components. In particular a comparison with more traditional...

  20. Quasiparticle pole strength in nuclear matter

    International Nuclear Information System (INIS)

    Poggioli, R.S.; Jackson, A.D.

    1975-01-01

    It is argued that single-particle-like behavior in nuclear matter is much less probable than Brueckner theory suggests. In particular, the quasiparticle pole strength is evaluated for nuclear matter and it is shown that, contrary to the spirit of Brueckner theory, low momentum states play a crucial role in determining the magnitude of z/sub k/sub F/. (auth)

  1. Kosovo : kannatlikkusele lootmine pole plaan / Chris Patten

    Index Scriptorium Estoniae

    Patten, Chris

    2007-01-01

    Autor leiab, et arvestades Kosovo elanike ülekaalukat soovi olla vaba Serbiast, riigist, mis üritas nad kõrvaldada, ning alternatiivi täielikku puudumist Belgradi poolt, pole rahvusvahelisel kogukonnal muud võimalust kui anda Kosovole iseseisvus

  2. Pole masses of quarks in dimensional reduction

    International Nuclear Information System (INIS)

    Avdeev, L.V.; Kalmykov, M.Yu.

    1997-01-01

    Pole masses of quarks in quantum chromodynamics are calculated to the two-loop order in the framework of the regularization by dimensional reduction. For the diagram with a light quark loop, the non-Euclidean asymptotic expansion is constructed with the external momentum on the mass shell of a heavy quark

  3. Third Pole Environment (TPE) -Latest Progress

    Science.gov (United States)

    Liu, Z.; Yao, T.; Zhang, F.; Yang, X.; Wang, W.; Ping, F.

    2014-12-01

    Centered on the Tibetan Plateau, the Third Pole region is a unique geographical unit, which represents one of the largest ice masses on the Earth. The region has great impacts on environmental changes in China, the Northern Hemisphere and the globe.It also demonstrates sensitive feedbacks to global changes and the impacts of anthropogenic activities in surrounding regions. Like the Arctic and Antarctica, the Third Pole region is an especially sensitive area that draws great attention from the scientific community. In 2009, with support from the Chinese Academy of Sciences and international organizations, the Third Pole Environment (TPE) program, led by Chinese scientists, was officially launched. The program focuses on the theme of "water-ice-air-ecosystem-human" interactions, with the aim to address the following scientific questions, such as the spatial and temporal characteristics of past environmental changes in the Third pole, the interactions between hydrosphere and cryosphere and hazard processes, the ecological systems' impacts on and response to environmental changes, and the impacts of anthropogenic activities on environmental changes in the region and adaptation strategies. The goal of the program is to reveal environmental change processes and mechanisms on the Third Pole and their influences on and responses to global changes, and thus to serve for enhancement of human adaptation to the changing environment and realization of human-nature harmony. Under the leadership of the co-chairs, and relying on Scientific Committee and the TPE office, the program has accomplished a number of scientific tasks since its inauguration. TPE has made tremendous progress in the research of glacier changes, interactions between the westerlies and monsoon, establishment of field stations, data sharing and education.

  4. Elemental Mercury Diffusion Processes and Concentration at the Lunar Poles

    Science.gov (United States)

    Moxley, Frederick; Killen, Rosemary M.; Hurley, Dana M.

    2011-01-01

    In 2009, the Lyman Alpha Mapping Project (LAMP) spectrograph onboard the Lunar Reconnaissance Orbiter (LRO) spacecraft made the first detection of element mercury (Hg) vapor in the lunar exosphere after the Lunar Crater Observing and Sensing Satellite (LCROSS) Centaur rocket impacted into the Cabeus crater in the southern polar region of the Moon. The lunar regolith core samples from the Apollo missions determined that Hg had a devolatilized pattern with a concentration gradient increasing with depth, in addition to a layered pattern suggesting multiple episodes of burial and volatile loss. Hg migration on the lunar surface resulted in cold trapping at the poles. We have modeled the rate at which indigenous Hg is lost from the regolith through diffusion out of lunar grains. We secondly modeled the migration of Hg vapor in the exosphere and estimated the rate of cold-trapping at the poles using a Monte Carlo technique. The Hg vapor may be lost from the exosphere via ionization, Jeans escape, or re-impact into the surface causing reabsorption.

  5. Fatigue failure and cracking in high mast poles.

    Science.gov (United States)

    2012-03-01

    This report presents the findings of a comprehensive research project to investigate the fatigue : cracking and failure of galvanized high mast illumination poles (HMIP). Ultrasonic inspection of : poles throughout the state has revealed the presence...

  6. Economics of Red Pine Management for Utility Pole Timber

    Science.gov (United States)

    Gerald H. Grossman; Karen Potter-Witter

    1991-01-01

    Including utility poles in red pine management regimes leads to distinctly different management recommendations. Where utility pole markets exist, managing for poles will maximize net returns. To do so, plantations should be maintained above 110 ft2/ac, higher than usually recommended. In Michigan's northern lower peninsula, approximately...

  7. Theoretical modeling and experimental analyses of laminated wood composite poles

    Science.gov (United States)

    Cheng Piao; Todd F. Shupe; Vijaya Gopu; Chung Y. Hse

    2005-01-01

    Wood laminated composite poles consist of trapezoid-shaped wood strips bonded with synthetic resin. The thick-walled hollow poles had adequate strength and stiffness properties and were a promising substitute for solid wood poles. It was necessary to develop theoretical models to facilitate the manufacture and future installation and maintenance of this novel...

  8. 46 CFR 111.79-3 - Grounding pole.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Grounding pole. 111.79-3 Section 111.79-3 Shipping COAST... REQUIREMENTS Receptacles § 111.79-3 Grounding pole. Each receptacle outlet that operates at 100 volts or more must have a grounding pole. ...

  9. Second-harmonic imaging of poled silica waveguides

    DEFF Research Database (Denmark)

    Arentoft, Jesper; Pedersen, Kjeld; Bozhevolnyi, Sergey I.

    2000-01-01

    Electric-field poled silica-based waveguides are characterized by measurements of second-harmonic generation (SHG) and of the linear electro-optic effect (LEO). A SHG scanning technique allowing for high-resolution imaging of poled devices is demonstrated. Scans along the direction of the poling...

  10. About Face

    Medline Plus

    Full Text Available ... What is AboutFace? Resources for Professionals Get Help PTSD We've been there. After a traumatic event — ... you're not feeling better, you may have PTSD (posttraumatic stress disorder). Watch the intro This is ...

  11. About Face

    Medline Plus

    Full Text Available ... to Content Menu Closed (Tap to Open) Home Videos by Topic Videos by Type Search All Videos PTSD Basics PTSD Treatment What is AboutFace? Resources for Professionals Get Help Home Watch Videos by Topic Videos by Type Search All Videos ...

  12. About Face

    Medline Plus

    Full Text Available ... at first. But if it's been months or years since the trauma and you're not feeling better, you may have PTSD (posttraumatic stress disorder). Watch the intro This is AboutFace In these videos, Veterans, family members, ...

  13. About Face

    Medline Plus

    Full Text Available ... traumatic event — like combat, an assault, or a disaster — it's normal to feel scared, keyed up, or sad at first. But if it's been months or years since the trauma and you're not feeling better, you may have PTSD (posttraumatic stress disorder). Watch the intro This is AboutFace In ...

  14. Ring modulator small-signal response analysis based on pole-zero representation.

    Science.gov (United States)

    Karimelahi, Samira; Sheikholeslami, Ali

    2016-04-04

    We present a closed-form expression for the small-signal response of a depletion-mode ring modulator and verify it by measurement results. Both electrical and optical behavior of micro-ring modulator as well as the loss variation due to the index modulation is considered in the derivation. This expression suggests that a ring modulator is a third-order system with one real pole, one zero and a pair of complex-conjugate poles. The exact positions of the poles/zero are given and shown to be dependent upon parameters such as electrical bandwidth, coupling condition, optical loss, and sign/value of laser detunings. We show that the location of zero is different for positive and negative detuning, and therefore, the ring modulator frequency response is asymmetric. We use the gain-bandwidth product as a figure of merit and calculate it for various pole/zero locations. We show that gain-bandwidth for the over-coupled ring modulator is superior compared to other coupling conditions. Also, we show that the gain-bandwidth product can be increased to a limit by increasing the electrical bandwidth.

  15. Clusters of cyclones encircling Jupiter's poles.

    Science.gov (United States)

    Adriani, A; Mura, A; Orton, G; Hansen, C; Altieri, F; Moriconi, M L; Rogers, J; Eichstädt, G; Momary, T; Ingersoll, A P; Filacchione, G; Sindoni, G; Tabataba-Vakili, F; Dinelli, B M; Fabiano, F; Bolton, S J; Connerney, J E P; Atreya, S K; Lunine, J I; Tosi, F; Migliorini, A; Grassi, D; Piccioni, G; Noschese, R; Cicchetti, A; Plainaki, C; Olivieri, A; O'Neill, M E; Turrini, D; Stefani, S; Sordini, R; Amoroso, M

    2018-03-07

    The familiar axisymmetric zones and belts that characterize Jupiter's weather system at lower latitudes give way to pervasive cyclonic activity at higher latitudes. Two-dimensional turbulence in combination with the Coriolis β-effect (that is, the large meridionally varying Coriolis force on the giant planets of the Solar System) produces alternating zonal flows. The zonal flows weaken with rising latitude so that a transition between equatorial jets and polar turbulence on Jupiter can occur. Simulations with shallow-water models of giant planets support this transition by producing both alternating flows near the equator and circumpolar cyclones near the poles. Jovian polar regions are not visible from Earth owing to Jupiter's low axial tilt, and were poorly characterized by previous missions because the trajectories of these missions did not venture far from Jupiter's equatorial plane. Here we report that visible and infrared images obtained from above each pole by the Juno spacecraft during its first five orbits reveal persistent polygonal patterns of large cyclones. In the north, eight circumpolar cyclones are observed about a single polar cyclone; in the south, one polar cyclone is encircled by five circumpolar cyclones. Cyclonic circulation is established via time-lapse imagery obtained over intervals ranging from 20 minutes to 4 hours. Although migration of cyclones towards the pole might be expected as a consequence of the Coriolis β-effect, by which cyclonic vortices naturally drift towards the rotational pole, the configuration of the cyclones is without precedent on other planets (including Saturn's polar hexagonal features). The manner in which the cyclones persist without merging and the process by which they evolve to their current configuration are unknown.

  16. The Gattini South Pole UV experiment

    Science.gov (United States)

    Moore, Anna M.; Ahmed, Sara; Ashley, Michael C. B.; Croner, Ernest; Delacroix, Alex; Ebihara, Yusuke; Fucik, Jason; Martin, D. Christopher; Velur, Viswa; Weatherwax, Allan

    2012-09-01

    The Gattini South Pole UV experiment (Gattini SPUV) was deployed to the South Pole dark sector in February 2010 and has recently completed a highly successful first season of winter time observations. The experiment has, for the first time ever, measured and categorized the optical night sky brightness at the very blue wavelengths. The experiment consists of a remotely operated 6” aperture custom designed telescope. The telescope feeds a blue sensitive imager with 4 degree field of view that contains a bank of 3 filters: SDSS g’, Bessel U and a custom “super U” filter specifically designed to probe the sky emission at wavelengths approaching the atmospheric cut-off. The filters are continually cycled with exposure times ranging from 30 to 300 seconds throughout the winter period. The telescope, in addition, feeds a 2 degree long slit VPH grating spectrograph with R~1000. The bandwidth is 350-450nm. The spectra are recorded simultaneously with the imager exposures. The experiment is designed for low temperature Antarctic operation and resides on the roof of the MAPO building in the South Pole Antarctic sector. The primary science goals are to categorize the Antarctic winter-time sky background at the very bluest of wavelengths as a pathfinder for the Antarctic Cosmic Web Imager. We present a technical overview of the experiment and results from the first winter season.

  17. The South Pole and the Ross Sea

    Science.gov (United States)

    2002-01-01

    This image shows a rare clear view of the South Pole (lower right) and the Ross Sea, Antarctica. The Sea-viewing Wide Field-of-view Sensor (SeaWiFS) acquired the scene on December 26, 2001. The geographic South Pole is located in the center of Antarctica, at an altitude of 2,900 meters (9,300 feet). It rests on a continent-wide ice sheet that is 2,870 m thick, with the underlying bedrock only 30 m (98 feet) above sea level. The ice underlying the South Pole is as much as 140,000 years old, and is currently accumulating at about 82 cm (32 inches) per year. Roughly 2,500 km (1,550 miles) away is the green water of the Ross Sea, which indicates the presence of large numbers of phytoplankton. This is a highly productive part of the world's oceans. Also note the ice gathered around McMurdo Sound, seen toward the lefthand shoreline of the Ross Sea, at the edge of the Ross Ice Shelf. According to National Science Foundation researchers, this ice is making it difficult for penguins to reach their food supply. Separating the continental Antarctic ice sheet from the Ross Sea are the Queen Maud Mountains and the Ross Ice Shelf. Image courtesy the SeaWiFS Project, NASA/Goddard Space Flight Center, and ORBIMAGE

  18. Pole-to-Pole Connections: Similarities between Arctic and Antarctic Microbiomes and Their Vulnerability to Environmental Change

    Directory of Open Access Journals (Sweden)

    Julia Kleinteich

    2017-11-01

    Full Text Available The global biogeography of microorganisms remains poorly resolved, which limits the current understanding of microbial resilience toward environmental changes. Using high-throughput 16S rRNA gene amplicon sequencing, we characterized the microbial diversity of terrestrial and lacustrine biofilms from the Arctic, Antarctic and temperate regions. Our analyses suggest that bacterial community compositions at the poles are more similar to each other than they are to geographically closer temperate habitats, with 32% of all operational taxonomic units (OTUs co-occurring in both polar regions. While specific microbial taxa were confined to distinct regions, representing potentially endemic populations, the percentage of cosmopolitan taxa was higher in Arctic (43% than in Antarctic samples (36%. The overlap in polar microbial OTUs may be explained by natural or anthropogenically-mediated dispersal in combination with environmental filtering. Current and future changing environmental conditions may enhance microbial invasion, establishment of cosmopolitan genotypes and loss of endemic taxa.

  19. Secondary electron emission yield on poled silica based thick films

    DEFF Research Database (Denmark)

    Braga, D.; Poumellec, B.; Cannas, V.

    2004-01-01

    injection, we pointed out an electric field 0.5 µm below the surface for our poling conditions and directed in the same direction as the external field applied during the poling process. Then, the dependence of on the injected dose of electrons allows us to deduce that the poling process disturbs the glass......Studies on the distribution of the electric field produced by a thermal poling process in a layer of Ge-doped silica on silicon substrate, by using secondary electron emission yield (SEEY) measurements () are presented. Comparing 0 between poled and unpoled areas, the SEEY at the origin of electron...... structure strongly enough for leading to a weak conductivity. It is then easy to display the poled areas. We have also pointed out an effect of the electric properties of the glass on the measurements obtained with the Electron Probe for MicroAnalysis....

  20. Long-Term Bending Creep Behavior of Thin-Walled CFRP Tendon Pretensioned Spun Concrete Poles

    Directory of Open Access Journals (Sweden)

    Giovanni P. Terrasi

    2014-07-01

    Full Text Available This paper discusses the long-term behavior of a series of highly-loaded, spun concrete pole specimens prestressed with carbon fiber-reinforced polymer (CFRP tendons, which were subjected to outdoor four-point bending creep tests since 1996 in the frame of collaboration with the Swiss precast concrete producer, SACAC (Società Anonima Cementi Armati Centrifugati. The 2 m span cylindrical beams studied are models for lighting poles produced for the last 10 years and sold on the European market. Five thin-walled pole specimens were investigated (diameter: 100 mm; wall-thickness: 25–27 mm. All specimens were produced in a pretensioning and spinning technique and were prestressed by pultruded CFRP tendons. Initially, two reference pole specimens were tested in quasi-static four-point bending to determine the short-term failure moment and to model the short-term flexural behavior. Then, three pole specimens were loaded to different bending creep moments: while the lowest loaded specimen was initially uncracked, the second specimen was loaded with 50% of the short-term bending failure moment and exhibited cracking immediately after load introduction. The highest loaded pole specimen sustained a bending moment of 72% of the short-term bending failure moment for 16.5 years before failing in July 2013, due to the bond failure of the tendons, which led to local crushing of the high-performance spun concrete (HPSC. Besides this, long-term monitoring of the creep tests has shown a limited time- and temperature-dependent increase of the deflections over the years, mainly due to the creep of the concrete. A concrete creep-based model allowed for the calculation of the long-term bending curvatures with reasonable accuracy. Furthermore, the pole specimens showed crack patterns that were stable over time and minimal slippage of the tendons with respect to the pole’s end-faces for the two lower load levels. The latter proves the successful and durable

  1. Multiple pole in the electron--hydrogen-atom scattering amplitude

    International Nuclear Information System (INIS)

    Amusia, M.Y.; Kuchiev, M.Y.

    1982-01-01

    It is demonstrated that the amplitude for electron--hydrogen-atom forward scattering has the third-order pole at the point E = -13.6 eV, E being the energy of the incident electron. The coefficients which characterize the pole are calculated exactly. The invalidity of the Born approximation is proved. The contribution of the pole singularity to the dispersion relation for the scattering amplitude is discussed

  2. Determination of the crystallite orientation distribution from direct pole figures

    International Nuclear Information System (INIS)

    Araujo Gomes, P.A.M. de.

    1977-01-01

    A method is described which allows to calculate the crystallite orientation distribution in polycrystalline material, from direct pole figures data of its crystallographic planes (Roe's Method). The programme was applied to (1010), (0002), (1011) and (1120) complete pole figures data for a commercial, thin sheet Zircaloy-4 tubing specimen. A semi-automatic Rigaku-Denki texture goniometer, which scans the reciprocal lattice sphere pointwise outputting the data in a punched tape, was used to obtain the pole figures. This is consistent with the results obtained through direct conclusion from the pole figures. (author)

  3. South Pole Region of the Moon as Seen by Clementine

    Science.gov (United States)

    1994-01-01

    Lunar mosaic of 1500 Clementine images of the south polar region of the moon. The projection is orthographic, centered on the south pole. The Schrodinger Basin (320 km in diameter) is located in the lower right of the mosaic. Amundsen-Ganswindt is the more subdued circular basin between Schrodinger and the pole. The polar regions of the moon are of special interest because of the postulated occurrence of ice in permanently shadowed areas. The south pole is of greater interest because the area that remains in shadow is much larger than that at the north pole.

  4. Thermal poling of multi-wire array optical fiber

    DEFF Research Database (Denmark)

    Huang, Lin; An, Honglin; Hayashi, Juliano G.

    2018-01-01

    We demonstrate in this paper thermal poling of multi-wire array fibers, which extends poling of fibers with two anodes to similar to 50 and similar to 500 wire array anodes. The second harmonic microscopy observations show that second order nonlinearity (SON) layers are developed surrounding all...... the rings of wires in the similar to 50 anode array fiber with poling of 1.8kV, 250 degrees C and 30min duration, and the outer rings of the similar to 500 anode array fiber at lower poling temperature. Our simulations based on a two-dimensional charge dynamics model confirm this can be explained...

  5. Bridging the Poles: Education Linked with Research

    Science.gov (United States)

    Pfirman, S.; Bell, R. E.; Turrin, M.; Maru, P.

    2004-12-01

    An international group of 65 scientists, educators and media specialists gathered at the "Bridging the Poles" workshop in Washington, DC on June 23-25, to define strategies that will inspire the general public and engage the next generation of polar scientists, engineers and leaders. This NSF-sponsored workshop was the first effort to develop an integrated education and outreach program for the International Polar Year of 2007-2009. Through a series of plenary talks and roundtable discussions, workshop participants focused on: engaging diverse communities, opportunities and needs for different levels, possibilities for thematic areas, and programs to feature nationally and internationally over the next 5 years. To maximize the potential of the International Polar Year, we need to coordinate research, education and outreach efforts, at the international as well as national level, with the goal of building an integrated and exciting public presence during 2007-2009. Successful education and outreach programming requires leveraging existing resources, creating new programs, connecting communities, and developing partnerships between agencies, scientists, educators, and the public. We need to consider the rich heritage of indigenous Arctic peoples, build capacity within communities through targeted efforts, and focus on making the poles relevant to diverse communities by using interdisciplinary approaches, e.g. cultural as well as scientific. A series of education and outreach packages for large-scale science endeavors should be rolled out to the public as major media events. The media -- television, radio and print -- as well as educators, zoos and museums are eager to use timely, accessible, and meaningful content. An Interagency Working Group on IPY Education and Outreach, with a staff and a central office, must be created to coordinate and leverage programs. A sophisticated web portal should be developed to serve content and contacts for researchers, educators, the

  6. Face-to-face: Perceived personal relevance amplifies face processing

    Science.gov (United States)

    Pittig, Andre; Schupp, Harald T.; Alpers, Georg W.

    2017-01-01

    Abstract The human face conveys emotional and social information, but it is not well understood how these two aspects influence face perception. In order to model a group situation, two faces displaying happy, neutral or angry expressions were presented. Importantly, faces were either facing the observer, or they were presented in profile view directed towards, or looking away from each other. In Experiment 1 (n = 64), face pairs were rated regarding perceived relevance, wish-to-interact, and displayed interactivity, as well as valence and arousal. All variables revealed main effects of facial expression (emotional > neutral), face orientation (facing observer > towards > away) and interactions showed that evaluation of emotional faces strongly varies with their orientation. Experiment 2 (n = 33) examined the temporal dynamics of perceptual-attentional processing of these face constellations with event-related potentials. Processing of emotional and neutral faces differed significantly in N170 amplitudes, early posterior negativity (EPN), and sustained positive potentials. Importantly, selective emotional face processing varied as a function of face orientation, indicating early emotion-specific (N170, EPN) and late threat-specific effects (LPP, sustained positivity). Taken together, perceived personal relevance to the observer—conveyed by facial expression and face direction—amplifies emotional face processing within triadic group situations. PMID:28158672

  7. Retratos da metrópole parisiense

    OpenAIRE

    Saint-Julien, Thérèse; Goix, Renaud Le

    2009-01-01

    « La métropole parisienne, centralité, inégalité, proximité » propõe uma leitura e uma interpretação das tendências do território da Île de France (a região que inclui Paris e sete outros départements), ou seja, uma grande metrópole mundial de cerca de 11,3 milhões de habitantes em 2004, ligada às redes da globalização e da metropolização. O livro esboça os traços principais de suas estruturas territoriais emergentes, sublinha os desafios, o alcance dos mesmos e as contradições. Sem pretensão...

  8. Retratos da metrópole parisiense

    Directory of Open Access Journals (Sweden)

    Thérèse Saint-Julien

    2009-07-01

    Full Text Available « La métropole parisienne, centralité, inégalité, proximité » propõe uma leitura e uma interpretação das tendências do território da Île de France (a região que inclui Paris e sete outros départements, ou seja, uma grande metrópole mundial de cerca de 11,3 milhões de habitantes em 2004, ligada às redes da globalização e da metropolização. O livro esboça os traços principais de suas estruturas territoriais emergentes, sublinha os desafios, o alcance dos mesmos e as contradições. Sem pretensão...

  9. Soft rot decay capabilities and interactions of fungi and bacteria from fumigated utility poles

    Energy Technology Data Exchange (ETDEWEB)

    Wang, C.J.K.; Worrall, J.J. (State Univ. of New York, Syracuse, NY (United States). Coll. of Environmental Science and Forestry)

    1992-11-01

    The objectives were to (1) identify microfungi and bacterial associates isolated from fumigated southern pine poles from EPRI project RP 1471-72, (2) study the soft-rot capabilities of predominant fungi, and (3) study interactions among microorganisms in relation to wood decay. Methods for identification followed standard techniques using morphological and physiological criteria. Soft-rot by microfungi alone and with bacteria was determined as weight loss and anatomical examination of wood blocks using light microscopy and limited electron microscopy. Acinetobacter calcoaceticus was the predominant bacterium. Twenty-one species of microfungi were identified including four new species. A book entitled IDENTIFICATION MANUAL FOR FUNGI FROM UTILITY POLES IN THE EASTERN UNITED STATES was published. An improved soft-rot test was devised. Fifty-one of 84 species (60%) of microfungi from poles tested were soft-rot positive; that is much greater than previously reported. Three types of anatomical damage of wood of pine or birch caused by soft-rot fungi were described. Interaction tests showed that, in some cases, there was a strong synergism between bacteria and fungi in causing weight loss, but results were inconsistent. Although soft rot is often most apparent under conditions of very high moisture, intermediate moisture levels appear to be optimal, as with basidiomycete decayers.

  10. Soft rot decay capabilities and interactions of fungi and bacteria from fumigated utility poles

    International Nuclear Information System (INIS)

    Wang, C.J.K.; Worrall, J.J.

    1992-11-01

    The objectives were to (1) identify microfungi and bacterial associates isolated from fumigated southern pine poles from EPRI project RP 1471-72, (2) study the soft-rot capabilities of predominant fungi, and (3) study interactions among microorganisms in relation to wood decay. Methods for identification followed standard techniques using morphological and physiological criteria. Soft-rot by microfungi alone and with bacteria was determined as weight loss and anatomical examination of wood blocks using light microscopy and limited electron microscopy. Acinetobacter calcoaceticus was the predominant bacterium. Twenty-one species of microfungi were identified including four new species. A book entitled IDENTIFICATION MANUAL FOR FUNGI FROM UTILITY POLES IN THE EASTERN UNITED STATES was published. An improved soft-rot test was devised. Fifty-one of 84 species (60%) of microfungi from poles tested were soft-rot positive; that is much greater than previously reported. Three types of anatomical damage of wood of pine or birch caused by soft-rot fungi were described. Interaction tests showed that, in some cases, there was a strong synergism between bacteria and fungi in causing weight loss, but results were inconsistent. Although soft rot is often most apparent under conditions of very high moisture, intermediate moisture levels appear to be optimal, as with basidiomycete decayers

  11. Jupiter's interior and deep atmosphere: The initial pole-to-pole passes with the Juno spacecraft

    Science.gov (United States)

    Bolton, S. J.; Adriani, A.; Adumitroaie, V.; Allison, M.; Anderson, J.; Atreya, S.; Bloxham, J.; Brown, S.; Connerney, J. E. P.; DeJong, E.; Folkner, W.; Gautier, D.; Grassi, D.; Gulkis, S.; Guillot, T.; Hansen, C.; Hubbard, W. B.; Iess, L.; Ingersoll, A.; Janssen, M.; Jorgensen, J.; Kaspi, Y.; Levin, S. M.; Li, C.; Lunine, J.; Miguel, Y.; Mura, A.; Orton, G.; Owen, T.; Ravine, M.; Smith, E.; Steffes, P.; Stone, E.; Stevenson, D.; Thorne, R.; Waite, J.; Durante, D.; Ebert, R. W.; Greathouse, T. K.; Hue, V.; Parisi, M.; Szalay, J. R.; Wilson, R.

    2017-05-01

    On 27 August 2016, the Juno spacecraft acquired science observations of Jupiter, passing less than 5000 kilometers above the equatorial cloud tops. Images of Jupiter's poles show a chaotic scene, unlike Saturn's poles. Microwave sounding reveals weather features at pressures deeper than 100 bars, dominated by an ammonia-rich, narrow low-latitude plume resembling a deeper, wider version of Earth's Hadley cell. Near-infrared mapping reveals the relative humidity within prominent downwelling regions. Juno's measured gravity field differs substantially from the last available estimate and is one order of magnitude more precise. This has implications for the distribution of heavy elements in the interior, including the existence and mass of Jupiter's core. The observed magnetic field exhibits smaller spatial variations than expected, indicative of a rich harmonic content.

  12. EFFECTS OF RUN-UP VELOCITY ON PERFORMANCE, KINEMATICS, AND ENERGY EXCHANGES IN THE POLE VAULT

    Directory of Open Access Journals (Sweden)

    Nicholas P. Linthorne

    2012-06-01

    Full Text Available This study examined the effect of run-up velocity on the peak height achieved by the athlete in the pole vault and on the corresponding changes in the athlete's kinematics and energy exchanges. Seventeen jumps by an experienced male pole vaulter were video recorded in the sagittal plane and a wide range of run-up velocities (4.5-8.5 m/s was obtained by setting the length of the athlete's run-up (2-16 steps. A selection of performance variables, kinematic variables, energy variables, and pole variables were calculated from the digitized video data. We found that the athlete's peak height increased linearly at a rate of 0.54 m per 1 m/s increase in run-up velocity and this increase was achieved through a combination of a greater grip height and a greater push height. At the athlete's competition run-up velocity (8.4 m/s about one third of the rate of increase in peak height arose from an increase in grip height and about two thirds arose from an increase in push height. Across the range of run-up velocities examined here the athlete always performed the basic actions of running, planting, jumping, and inverting on the pole. However, he made minor systematic changes to his jumping kinematics, vaulting kinematics, and selection of pole characteristics as the run-up velocity increased. The increase in run-up velocity and changes in the athlete's vaulting kinematics resulted in substantial changes to the magnitudes of the energy exchanges during the vault. A faster run-up produced a greater loss of energy during the take-off, but this loss was not sufficient to negate the increase in run-up velocity and the increase in work done by the athlete during the pole support phase. The athlete therefore always had a net energy gain during the vault. However, the magnitude of this gain decreased slightly as run-up velocity increased

  13. Spectral analysis of gluonic pole matrix elements for fragmentation

    NARCIS (Netherlands)

    Gamberg, L. P.; Mukherjee, A.B.; Mulders, P.J.G.

    2008-01-01

    The nonvanishing of gluonic pole matrix elements can explain the appearance of single spin asymmetries in high-energy scattering processes. We use a spectator framework approach to investigate the spectral properties of quark-quark-gluon correlators and use this to study gluonic pole matrix

  14. pbx is required for pole and eye regeneration in planarians.

    Science.gov (United States)

    Chen, Chun-Chieh G; Wang, Irving E; Reddien, Peter W

    2013-02-01

    Planarian regeneration involves regionalized gene expression that specifies the body plan. After amputation, planarians are capable of regenerating new anterior and posterior poles, as well as tissues polarized along the anterior-posterior, dorsal-ventral and medial-lateral axes. Wnt and several Hox genes are expressed at the posterior pole, whereas Wnt inhibitory genes, Fgf inhibitory genes, and prep, which encodes a TALE-family homeodomain protein, are expressed at the anterior pole. We found that Smed-pbx (pbx for short), which encodes a second planarian TALE-family homeodomain transcription factor, is required for restored expression of these genes at anterior and posterior poles during regeneration. Moreover, pbx(RNAi) animals gradually lose pole gene expression during homeostasis. By contrast, pbx was not required for initial anterior-posterior polarized responses to wounds, indicating that pbx is required after wound responses for development and maintenance of poles during regeneration and homeostatic tissue turnover. Independently of the requirement for pbx in pole regeneration, pbx is required for eye precursor formation and, consequently, eye regeneration and eye replacement in homeostasis. Together, these data indicate that pbx promotes pole formation of body axes and formation of regenerative progenitors for eyes.

  15. Second harmonic generation from corona-poled polymer thin films ...

    Indian Academy of Sciences (India)

    2014-02-09

    Feb 9, 2014 ... We characterize thermal stability of second harmonic generation (SHG) properties of four different Y-type polymers poled using corona poling method. These polymers are based on donor–acceptor–donor-type repeating unit with different aromatic moieties acting as donors and dicyanomethylene acting as ...

  16. Derivation of nominal strength for wood utility poles

    Science.gov (United States)

    Ronald W. Wolfe; Jozsef Bodig; Patricia Lebow

    2001-01-01

    The designated fiber stress values published in the American National Standards Institute Standard for Poles, ANSI 05.1, no longer reflect the state of the knowledge. These values are based on a combination of test data from small clear wood samples and small poles (

  17. Second harmonic generation from corona-poled polymer thin films ...

    Indian Academy of Sciences (India)

    2014-02-09

    Feb 9, 2014 ... Abstract. We characterize thermal stability of second harmonic generation (SHG) properties of four different Y-type polymers poled using corona poling method. These polymers are based on donor–acceptor–donor-type repeating unit with different aromatic moieties acting as donors and dicyanomethylene ...

  18. Three Phase Soft Commutation Auxilary Resonant Pole Inverter

    OpenAIRE

    Vaclav Sladecek

    2006-01-01

    This paper covers the circuit modification of the power part of the inverter with auxiliary resonant poles utilising configuration of switches realised with routinely produced IGBT modules. Covered is also the control optimisation which goal is the minimisation of switching of the auxiliary resonant pole. Presented results were gained on a prototype of an inverter laboratory sample.

  19. Finite element analyses of wood laminated composite poles

    Science.gov (United States)

    Cheng Piao; Todd F. Shupe; R.C. Tang; Chung Y. Hse

    2005-01-01

    Finite element analyses using ANSYS were conducted on orthotropic, polygonal, wood laminated composite poles subjected to a body force and a concentrated load at the free end. Deflections and stress distributions of small-scale and full-size composite poles were analyzed and compared to the results obtained in an experimental study. The predicted deflection for both...

  20. Gluability of out-of-service utility poles

    Science.gov (United States)

    Han Roliadi; Chung Y. Hse; Elvin T. Choong; Todd F. Shupe

    2000-01-01

    This investigation determined the gluability of weathered, out-of-service southern yellow pine (SYP) (Pinus spp.) utility poles. Three types of adhesives were used: resorcinol-phenol formaldehyde (RPF), polyvinyl acetate (PVA), and casein. The poles consisted of two service duration groups: 5 and 25 years. Longer weathering caused greater reduction in creosote content...

  1. Solar Open Flux Migration from Pole to Pole: Magnetic Field Reversal.

    Science.gov (United States)

    Huang, G-H; Lin, C-H; Lee, L C

    2017-08-25

    Coronal holes are solar regions with low soft X-ray or low extreme ultraviolet intensities. The magnetic fields from coronal holes extend far away from the Sun, and thus they are identified as regions with open magnetic field lines. Coronal holes are concentrated in the polar regions during the sunspot minimum phase, and spread to lower latitude during the rising phase of solar activity. In this work, we identify coronal holes with outward and inward open magnetic fluxes being in the opposite poles during solar quiet period. We find that during the sunspot rising phase, the outward and inward open fluxes perform pole-to-pole trans-equatorial migrations in opposite directions. The migration of the open fluxes consists of three parts: open flux areas migrating across the equator, new open flux areas generated in the low latitude and migrating poleward, and new open flux areas locally generated in the polar region. All three components contribute to the reversal of magnetic polarity. The percentage of contribution from each component is different for different solar cycle. Our results also show that the sunspot number is positively correlated with the lower-latitude open magnetic flux area, but negatively correlated with the total open flux area.

  2. Effect of pole number and slot number on performance of dual rotor permanent magnet wind power generator using ferrite magnets

    Directory of Open Access Journals (Sweden)

    Peifeng Xu

    2017-05-01

    Full Text Available Dual rotor permanent magnet (DRPM wind power generator using ferrite magnets has the advantages of low cost, high efficiency, and high torque density. How to further improve the performance and reduce the cost of the machine by proper choice of pole number and slot number is an important problem to be solved when performing preliminarily design a DRPM wind generator. This paper presents a comprehensive performance comparison of a DRPM wind generator using ferrite magnets with different slot and pole number combinations. The main winding factors are calculated by means of the star of slots. Under the same machine volume and ferrite consumption, the flux linkage, back-electromotive force (EMF, cogging torque, output torque, torque pulsation, and losses are investigated and compared using finite element analysis (FEA. The results show that the slot and pole number combinations have an important impact on the generator properties.

  3. Pole Dancing Auto-ethnography – Practice, Pedagogy, Performance

    Directory of Open Access Journals (Sweden)

    Amy Patricia Cadwallader

    2017-02-01

    Full Text Available In this research paper, the author addresses the following four questions: 1 What are the implications of bringing pole dancing into concert dance, not as a caricature or theatrical version of what is performed in strip clubs, but as its own, free-standing art form? 2 In what ways will years of ballet and modern dance training influence the type of dancing that emerges from dancers when poles and other apparatuses are introduced? 3 How can the author create an original pole dancing style and pedagogical methods for teaching it? 4 Who participates in pole fitness classes and how does the demographic change based on location? What about when pole fitness classes are offered in an academic setting? The author shares first-hand experiences of investigating pole dancing in fitness classes, attending performances, engaging in a rehearsal process with highly trained dancers, and teaching pole dancing to movers with a wide range of abilities. The author addresses how research plans changed as she encountered limitations of budget and time constraints. The author also elaborates on the creative process that she engaged in with her thesis cast, collaborators, and supporting designers in the making of Super-beneath, a theatrical dance work that uses five, free-standing poles. She outline the vignettes, overall structure, and narrative of the work. The author then discusses where this research fits into the larger field of pole dancing, and the even larger field of dance. In the final sections of this paper, the author describes her pedagogical practices relating to pole classes, what “practice as research” means to her, and how she would like to continue on this research trajectory in the future.

  4. Simplified Analytic Approach of Pole-to-Pole Faults in MMC-HVDC for AC System Backup Protection Setting Calculation

    Directory of Open Access Journals (Sweden)

    Tongkun Lan

    2018-01-01

    Full Text Available AC (alternating current system backup protection setting calculation is an important basis for ensuring the safe operation of power grids. With the increasing integration of modular multilevel converter based high voltage direct current (MMC-HVDC into power grids, it has been a big challenge for the AC system backup protection setting calculation, as the MMC-HVDC lacks the fault self-clearance capability under pole-to-pole faults. This paper focused on the pole-to-pole faults analysis for the AC system backup protection setting calculation. The principles of pole-to-pole faults analysis were discussed first according to the standard of the AC system protection setting calculation. Then, the influence of fault resistance on the fault process was investigated. A simplified analytic approach of pole-to-pole faults in MMC-HVDC for the AC system backup protection setting calculation was proposed. In the proposed approach, the derived expressions of fundamental frequency current are applicable under arbitrary fault resistance. The accuracy of the proposed approach was demonstrated by PSCAD/EMTDC (Power Systems Computer-Aided Design/Electromagnetic Transients including DC simulations.

  5. Heavy Cratering near Callisto's South Pole

    Science.gov (United States)

    1997-01-01

    Images from NASA's Galileo spacecraft provide new insights into this region near Callisto's south pole. This two frame mosaic shows a heavily cratered surface with smooth plains in the areas between craters. North is to the top of the image. The smoothness of the plains appears to increase toward the south pole, approximately 480 kilometers (293 miles) south of the bottom of the image. This smoothness of Callisto's surface was not evident in images taken during the 1979 flyby of NASA's Voyager spacecraft because the resolution was insufficient to show the effect. This smooth surface, and the process(es) that cause it, are among the most intriguing aspects of Callisto. Although not fully understood, the process(es) responsible for this smoothing could include erosion by tiny meteorites and energetic ions. Some craters, such as Keelut, the 47 kilometer (29 mile) crater in the lower right corner, have sharp, well defined rims. Keelut contains an inner ring surrounding a central depression about 17 kilometers (11 miles) in diameter. Keelut, and the more irregularly shaped, degraded Reginleif, the 32 kilometer (19.5 mile) crater in the top center of the image, are very shallow and have flat floors. Crater forms can be seen down to less than 2 kilometers (1.2 miles) in diameter in the image. Each picture element (pixel) in this image is approximately 0.68 kilometers (0.41 miles) across.This image which was taken by the Galileo spacecraft's solid state imaging (CCD) system during its eighth orbit around Jupiter, on May 6th, 1997. The center of the image is located at 71.3 degrees south latitude, 97.6 degrees west longitude, and was taken when the spacecraft was approximately 35,470 kilometers (21,637 miles) from Callisto.The Jet Propulsion Laboratory, Pasadena, CA manages the mission for NASA's Office of Space Science, Washington, DC.This image and other images and data received from Galileo are posted on the World Wide Web, on the Galileo mission home page at URL http

  6. Noise generation mechanisms in claw pole alternators

    Science.gov (United States)

    Eversman, W.; Burns, S.; Pekarek, S.; Bai, Hua; Tichenor, J.

    2005-05-01

    Noise of claw pole alternators, generated electromagnetically and structurally radiated, has been the subject of an extensive research program. The goal has been to identify and reduce noise radiation mechanisms in claw pole (Lundell) alternators used in automotive applications. Two approaches have been followed. In the first, electromagnetic sources of noise have been investigated by lumped parameter and magnetically equivalent circuit modeling and simulation, and by related experimentation. This is the subject of separate papers. The second, concurrent study reported here has investigated machine and mount responses to an electromagnetically generated torque ripple. Modeling and experimentation has led to the conclusion that there exists a high correlation between electromagnetic sources, torque ripple, and radiated noise. Experimentation also has led to the conclusion that noise characteristics of a given machine are substantially altered by modification of the mounting configuration. The work reported here involves modeling, simulation, and experiment to isolate machine dynamic characteristics and mounting geometries which contribute to strong coupling between torque ripple and machine/mount dynamic response. A low-order model of the alternator which includes shaft flexibility, gyroscopic effects, shaft bearing asymmetry, mounting lug geometry, and mounting structure dynamics has been created. The model provides a rapid simulation of dynamic response in the form of a transfer function between torque ripple and mounting forces. Generic studies of a simplified mounting structure coupled to the machine model are presented here. Acoustic testing of several machine configurations on a production mount has been carried out to investigate 36th order noise in three phase machines and 72nd order noise in six-phase machines. Electromagnetic modeling and dynamic response simulations suggest that the six-phase machine is inherently quieter. This is supported by

  7. Territorial Balancing of Poles of Development

    Directory of Open Access Journals (Sweden)

    CLAUDIA POPESCU

    2008-01-01

    Full Text Available The paper is part of the study "Specific problems of the development of the settlement network in south-eastern Romania. Regions of development 3 (South, 4 (South-West and 8 (Bucharest-Ilfov" elaborated during 2004 – 2006, within the AMTRANS programme funded by the Ministry of Education and Research, coordinated by INCD – URBANPROIECT in partnership with the Institute of Geography of the Romanian Academy and the Qualification in Statistics National Centre. The general objective of the project was sustainable and balanced spatial development of the settlement network and promotion of new relationships between urban and rural. Concretely, the study has produced a model of a polycentric and balanced settlement network according to the European principles. The case study testing and validating this model took place in southern Romania, territory exhibiting acutely the entire range of problems related to the state of the settlement network: profoundly large rural areas, accentuated dynamics of declaring new cities without sufficient evidence, excessive polarization exercised by Bucharest, etc. The paper presents the intervention directions needed to balance in the territory urban poles within the studied area, focusing on the establishment of orientation policies to consolidate the role of each settlement based on the hierarchical level of importance: European, national, regional, and local. The paper also identifies possible functional urban areas: the metropolitan area of Bucharest, areas of potential strategic integration, areas of cooperation between the small and medium-sized cities and the rural regions. Within each of these areas, the paper proposes to establish new relationships between urban and rural based on partnership, involving cooperation and coordination in achieving common goals.The study considers that the poles of development are the key element of proposed model, and their identification, formation, and balanced distribution

  8. Pole preservatives in soils adjacent to in-service utility poles in the United States. Final report

    International Nuclear Information System (INIS)

    Taylor, B.B.; Ripp, J.A.; Ladwig, K.

    1997-12-01

    As a result of increasing concerns regarding the environmental fate of wood preservatives, EPRI carried out a study of soils in the vicinity of in-service wood pole sites. More than 8,000 soil samples adjacent to 180 PCP-treated and 22 creosote-treated wood poles were collected and analyzed for chemicals of interest. The results showed that concentrations of wood preservative chemicals tended to be highest in soils located in very close proximity to the poles with rapid decreases in concentrations observed with distance from the poles. Soil partitioning, biodegradation, and modeling studies on PCP were also completed to augment the soil data and to provide additional information on the release, migration, and fate of wood preservatives at in-service pole sites

  9. Pole-factorization theorem in quantum electrodynamics

    International Nuclear Information System (INIS)

    Stapp, H.P.

    1996-01-01

    In quantum electrodynamics a classical part of the S-matrix is normally factored out in order to obtain a quantum remainder that can be treated perturbatively without the occurrence of infrared divergences. However, this separation, as usually performed, introduces spurious large-distance effects that produce an apparent breakdown of the important correspondence between stable particles and poles of the S-matrix, and, consequently, lead to apparent violations of the correspondence principle and to incorrect results for computations in the mesoscopic domain lying between the atomic and classical regimes. An improved computational technique is described that allows valid results to be obtained in this domain, and that leads, for the quantum remainder, in the cases studied, to a physical-region singularity structure that, as regards the most singular parts, is the same as the normal physical-region analytic structure in theories in which all particles have non-zero mass. The key innovations are to define the classical part in coordinate space, rather than in momentum space, and to define there a separation of the photon-electron coupling into its classical and quantum parts that has the following properties: (1) The contributions from the terms containing only classical couplings can be summed to all orders to give a unitary operator that generates the coherent state that corresponds to the appropriate classical process, and (2) The quantum remainder can be rigorously shown to exhibit, as regards its most singular parts, the normal analytic structure. (orig.)

  10. π π scattering by pole extrapolation methods

    International Nuclear Information System (INIS)

    Lott, F.W. III.

    1977-01-01

    A 25-inch hydrogen bubble chamber was used at the Lawrence Berkeley Laboratory Bevatron to produce 300,000 pictures of π + p interactions at an incident momentum of the π + of 2.67 GeV/c. The 2-prong events were processed using the FSD and the FOG-CLOUDY-FAIR data reduction system. Events of the nature π + p → π + pπ 0 and π + p → π + π + n with values of momentum transfer to the proton of -t less than or equal to 0.238 GeV 2 were selected. These events were used to extrapolate to the pion pole (t = m/sub π/ 2 ) in order to investigate the π π interaction with isospins of both T = 1 and T = 2. Two methods were used to do the extrapolation: the original Chew-Low method developed in 1959 and the Durr-Pilkuhn method developed in 1965 which takes into account centrifugal barrier penetration factors. At first it seemed that, while the Durr-Pilkuhn method gave better values for the total π π cross section, the Chew-Low method gave better values for the angular distribution. Further analysis, however, showed that if the requirement of total OPE (one-pion-exchange) were dropped, then the Durr-Pilkuhn method gave more reasonable values of the angular distribution as well as for the total π π cross section

  11. The North Celestial Pole Monitoring Project

    Science.gov (United States)

    Blake, R. M.; Castelaz, M.; Phillips, J.

    2005-05-01

    In the past ten years a renaissance has occurred in the study of transient phenomena using small, dedicated optical telescopes. This has largely been driven by the successful detection of planetary transits with small telescopes (Henry et al. 2000) and the successful recovery of optical afterglows of gamma ray bursts (e.g. Halpern et al. 1997). The telescopes involved are designed to slew at rapid rates accurately across the sky when a burst alert occurs, or to study a single patch of sky to detect transits. We have constructed a dedicated robotic instrument to monitor the region within 4 degrees of the north celestial pole continuously every clear night. Using a sequence of short and long exposures the telescope collects data to conduct searches for transient and variable objects and monitor the Cepheid variable Polaris. Previous authors (Kamper et al. 1984; Evans et al. 1998) have observed Polaris to nearly cease its pulsation, a unique behavior for a Cepheid variable. Monitoring Polaris with high secular coverage should help explain this behavior. We describe here the design of the observatory, its operation and control systems and give preliminary examples of the data products from this unique project.

  12. Study on Pole Arrangement of the CEDM Coils

    International Nuclear Information System (INIS)

    Park, Jin Seok; Lee, Myoung Goo; Kim, Hyun Min; Cho, Yeon Ho; Choi, Taek Sang

    2013-01-01

    The coil stack assembly is important for reliable operation of the CEDM, there have been efforts to improve the design by optimizing the design parameters such as dimensions and winding turns. However, magnetic forces of the CEDM can also change by different pole arrangement even if their design parameters are the same. Since the latch coil and lift coil are installed connected to each other, they produce magnetically coupled field when they are energized at the same time. This coupling field can affect the magnetic force of the CEDM significantly. In this paper, coil pole arrangement effects are studied. Electro-magnetic analysis is performed for the different pole arrangements of the CEDM coils to calculate the magnetic forces. Pole arrangement effects on magnetic forces were studied by static analysis of the CEDM magnetic field. Magnetic forces were calculated and compared for the two different pole arrangements of the coils. The results show that the magnetic poles of the lift coil and latch coil shall be arranged to have the same magnetic pole direction to achieve higher magnetic force

  13. Evidence of Space-Charge Effects in Thermal Poling

    DEFF Research Database (Denmark)

    Wu, X.; Arentoft, Jesper; Wong, D.

    1999-01-01

    The in situ thermal poling processes in germanosilicate fibers for positive and negative poling voltages are significantly different. Thermal poling of silica fibers consists of two processes: the faster linear process of charge migration and the subsequent single exponential process of charge...... ionization. Both the shielding electrical field due to charge migration and the ionization electrical field due to charge ionization are able to be frozen-in at room temperature acid lead to the residual linear electrooptic effects, The observations support that the mechanism of the induced electrooptic...... effects is based on space charge electrical fields instead of dipole/bond orientation....

  14. PopZ identifies the new pole, and PodJ identifies the old pole during polar growth in Agrobacterium tumefaciens.

    Science.gov (United States)

    Grangeon, Romain; Zupan, John R; Anderson-Furgeson, James; Zambryski, Patricia C

    2015-09-15

    Agrobacterium tumefaciens elongates by addition of peptidoglycan (PG) only at the pole created by cell division, the growth pole, whereas the opposite pole, the old pole, is inactive for PG synthesis. How Agrobacterium assigns and maintains pole asymmetry is not understood. Here, we investigated whether polar growth is correlated with novel pole-specific localization of proteins implicated in a variety of growth and cell division pathways. The cell cycle of A. tumefaciens was monitored by time-lapse and superresolution microscopy to image the localization of A. tumefaciens homologs of proteins involved in cell division, PG synthesis and pole identity. FtsZ and FtsA accumulate at the growth pole during elongation, and improved imaging reveals FtsZ disappears from the growth pole and accumulates at the midcell before FtsA. The L,D-transpeptidase Atu0845 was detected mainly at the growth pole. A. tumefaciens specific pole-organizing protein (Pop) PopZAt and polar organelle development (Pod) protein PodJAt exhibited dynamic yet distinct behavior. PopZAt was found exclusively at the growing pole and quickly switches to the new growth poles of both siblings immediately after septation. PodJAt is initially at the old pole but then also accumulates at the growth pole as the cell cycle progresses suggesting that PodJAt may mediate the transition of the growth pole to an old pole. Thus, PopZAt is a marker for growth pole identity, whereas PodJAt identifies the old pole.

  15. European cinema: face to face with Hollywood

    NARCIS (Netherlands)

    Elsaesser, T.

    2005-01-01

    In the face of renewed competition from Hollywood since the early 1980s and the challenges posed to Europe's national cinemas by the fall of the Wall in 1989, independent filmmaking in Europe has begun to re-invent itself. European Cinema: Face to Face with Hollywood re-assesses the different

  16. Mapping Teacher-Faces

    Science.gov (United States)

    Thompson, Greg; Cook, Ian

    2013-01-01

    This paper uses Deleuze and Guattari's concept of faciality to analyse the teacher's face. According to Deleuze and Guattari, the teacher-face is a special type of face because it is an "overcoded" face produced in specific landscapes. This paper suggests four limit-faces for teacher faciality that actualise different mixes of significance and…

  17. Novel attempt to create uniform magnetic-field space generated by face-to-face settled HTS bulk magnets

    International Nuclear Information System (INIS)

    Oka, Tetsuo; Ichiju, Kana; Higa, Kazuya; Fukui, Satoshi; Ogawa, Jun; Sato, Takao; Yokoyama, Kazuya; Nakamura, Takashi

    2017-01-01

    Various experimental attempts have been made to obtain a uniform magnetic field in the space between face-to-face HTS bulk magnets that could possibly be utilized as NMR magnets. In general, the magnetic fields emitted from the magnetic pole surfaces containing HTS bulk magnets are characterized as non-uniform field distributions. Since the NMR magnets require highly uniform magnetic-field spaces, it has been assumed to be difficult to form uniform magnetic-field spaces between magnetic poles placed face-to-face. The authors modified the shapes of the magnetic-field distribution from convex to concave by attaching ferromagnetic iron plates to the pole surfaces. The magnets were then set face-to-face with various gaps of 30-70 mm, and the experimental data on magnetic-field uniformity was precisely measured in the space. In order to detect the NMR signals, the target performance for uniformity was set as 1,500 ppm throughout the 4-mm span on the x-axis, which is equivalent to performance in the past when the world's first detection of NMR signals was observed in the bore of hollow-type HTS bulk magnets. When we combined the concave and convex field distributions to compensate the uneven field distributions, the data of the best uniformity reached 358 ppm and 493 ppm in the 30 mm and 50 mm gaps, respectively, which exceeded the target value for the purpose of detecting the NMR signals within the space. Furthermore, it was shown that the field distributions change from concave to convex shape without any change at 1.1 T in the range from 7 to 11 mm in the 30-mm gap, indicating that the distributions are uniform. This suggests the possibility that the uniform magnetic-field space between the HTS bulk magnets set face-to-face expands. (author)

  18. Characterization of Periodically Poled Nonlinear Materials Using Digital Image Processing

    National Research Council Canada - National Science Library

    Alverson, James R

    2008-01-01

    .... A new approach based on image processing across an entire z+ or z- surface of a poled crystal allows for better quantification of the underlying domain structure and directly relates to device performance...

  19. POLE mutations in families predisposed to cutaneous melanoma

    DEFF Research Database (Denmark)

    Aoude, Lauren G; Heitzer, Ellen; Johansson, Peter

    2015-01-01

    Germline mutations in the exonuclease domain of POLE have been shown to predispose to colorectal cancers and adenomas. POLE is an enzyme involved in DNA repair and chromosomal DNA replication. In order to assess whether such mutations might also predispose to cutaneous melanoma, we interrogated...... whole-genome and exome data from probands of 34 melanoma families lacking pathogenic mutations in known high penetrance melanoma susceptibility genes: CDKN2A, CDK4, BAP1, TERT, POT1, ACD and TERF2IP. We found a novel germline mutation, POLE p.(Trp347Cys), in a 7-case cutaneous melanoma family....... Functional assays in S. pombe showed that this mutation led to an increased DNA mutation rate comparable to that seen with a Pol ε mutant with no exonuclease activity. We then performed targeted sequencing of POLE in 1243 cutaneous melanoma cases and found that a further ten probands had novel or rare...

  20. New tilted-poles Wien filter with enhanced performance

    Science.gov (United States)

    Leal-Quiros, E.; Prelas, M. A.

    1989-03-01

    The Wien filter is an E×B deflecting analyzer with the electrostatic field perpendicular to the magnetostatic field. The twofold functions of the Wien filter are as an energy analyzer as well as a mass analyzer. It has very high resolution for paraxial charged-particle beams with V=E/B, the Wien velocity. Two Wien filters, a tilted-poles Wien filter, and a classical parallel-rectangular-poles Wien filter were built and tested for electrons up to 3.5 keV and protons beams of 200 eV. (The tilted-poles Wien filter is a new diagnostic developed by the authors.) The performance of the two is compared, and the tilted-poles Wien filter has superior resolution to the classical Wien filter. Both Wien filters appear to have features useful for high-temperature plasma diagnostics, including simultaneous measurement of energy and mass spectra, and high resolution.

  1. New tilted-poles Wien filter with enhanced performance

    Energy Technology Data Exchange (ETDEWEB)

    Leal-Quiros, E.; Prelas, M.A.

    1989-03-01

    The Wien filter is an E x B deflecting analyzer with the electrostatic field perpendicular to the magnetostatic field. The twofold functions of the Wien filter are as an energy analyzer as well as a mass analyzer. It has very high resolution for paraxial charged-particle beams with V = E/B, the Wien velocity. Two Wien filters, a tilted-poles Wien filter, and a classical parallel-rectangular-poles Wien filter were built and tested for electrons up to 3.5 keV and protons beams of 200 eV. (The tilted-poles Wien filter is a new diagnostic developed by the authors.) The performance of the two is compared, and the tilted-poles Wien filter has superior resolution to the classical Wien filter. Both Wien filters appear to have features useful for high-temperature plasma diagnostics, including simultaneous measurement of energy and mass spectra, and high resolution.

  2. Pacific Albacore Troll and Pole-and-line Fisheries

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The North Pacific and South Pacific Albacore Troll and Pole-and-line Fisheries project contains landings, logbooks, and size composition data from U.S.A. troll and...

  3. Micrometeorites from the South Pole Water Well, Version 1

    Data.gov (United States)

    National Aeronautics and Space Administration — Micrometeorites dated between 1100 A.D. to 1500 A.D. were collected from the bottom of the South Pole Water Well in December 1995. Element analyses of 181 cosmic...

  4. Detection of Cavities Using Pole-Dipole Resistivity Technique

    OpenAIRE

    Elawadi, Eslam; El-Qady, Gad; Salem, Ahmed; Ushijima, Keisuke

    2001-01-01

    Using pole-dipole array, electrical resistivity survey was conducted to investigate the subsurface under a subsiding building located in Kita Kyushu area, Japan. The resistivity measurements were acquired along two traverse lines and interpreted using a g

  5. Methane Isotopes in South Pole Firn Air, 2008, Version 1

    Data.gov (United States)

    National Aeronautics and Space Administration — This data set contains depth profiles for delta carbon-13 (δ13C) and delta deuterium (δD) of methane (CH4) in South Pole firn air. The investigators obtained air...

  6. South Pole Snow Pit, 1988 and 1989, Version 1

    Data.gov (United States)

    National Aeronautics and Space Administration — Information from 6-meter snow pits dug close to the South Pole in austral summer 1988-1989 by the Glacier Research Group of the University of New Hampshire (location...

  7. Dynamic Electromechanical Characterization of Axially Poled PZT 95/5

    International Nuclear Information System (INIS)

    Chhabildas, Lalit C.; Furnish, Michael D.; Montgomery, Stephen T.; Setchell, Robert E.

    1999-01-01

    We are conducting a comprehensive experimental study of the electromechanical behavior of poled PZT 95/5 (lead zirconate titanate). As part of this study, eight plane-wave tests have been conducted on axially poled PZT 95/5 at stress levels ranging from 0.9 to 4.6 GPa, using VISAR and electrical diagnostics. Observed wave velocities were slightly decreased from ultrasonic velocity, by contrast' with unpoled samples. Compression waveforms show a step at 0.6 GPa more marked than for normally poled or unpoled samples; this may correspond to a poling effect on the ferroelectric/antiferroelectric transition. A similar step is observed on release. The released charge upon loading to 0.9 GPa is consistent with nearly complete depoling. Loading to higher stresses gave lower currents (factor of 10), suggesting shock-induced conductivity or electrical breakdown

  8. Multijet final states: exact results and the leading pole approximation

    International Nuclear Information System (INIS)

    Ellis, R.K.; Owens, J.F.

    1984-09-01

    Exact results for the process gg → ggg are compared with those obtained using the leading pole approximation. Regions of phase space where the approximation breaks down are discussed. A specific example relevant for background estimates to W boson production is presented. It is concluded that in this instance the leading pole approximation may underestimate the standard QCD background by more than a factor of two in certain kinematic regions of physical interest

  9. Second-harmonic scanning optical microscopy of poled silica waveguides

    DEFF Research Database (Denmark)

    Pedersen, Kjeld; Bozhevolnyi, Sergey I.; Arentoft, Jesper

    2000-01-01

    Second-harmonic scanning optical microscopy (SHSOM) is performed on electric-field poled silica-based waveguides. Two operation modes of SHSOM are considered. Oblique transmission reflection and normal reflection modes are used to image the spatial distribution of nonlinear susceptibilities...... and limitations of the two operation modes when used for SHSOM studies of poled silica-based waveguides are discussed. The influence of surface defects on the resulting second-harmonic images is also considered. ©2000 American Institute of Physics....

  10. International Youth Conference on the Poles

    Science.gov (United States)

    Church, A. K.; Kuhn, T. S.; Baeseman, J.; Garmulewicz, A.; Raymond, M.; Salmon, R.

    2006-12-01

    The International Polar Year (IPY) is an international effort, involving more than 50 countries, to focus research in both the sciences and social sciences on the world's Polar Regions. In order to secure youth involvement in the IPY, the Youth Steering Committee (YSC) has been formed, aiming specifically to network young polar researchers from all backgrounds enabling collaboration and to involve this group in outreach focused towards other young people. A conference targeted directly at an audience of early career researchers and international youth will be central to fulfilling these aims. The YSC has therefore developed the concept of the International Youth Conference on the Poles (IYCP). Proposed for 2008, this conference will bring together youth from a diverse set of backgrounds and nationalities to discuss the issues affecting the Polar Regions, their effects on a global scale and ways of addressing these issues. The conference will also serve to highlight ongoing IPY research, especially research being undertaken by young researchers, and provide a perennial framework for youth involvement in polar research and policies. The IYCP will run for three days in May 2008, attracting an international youth audience, as well as representatives from polar organizations, teachers, politicians, policy makers, the general public and media. The IYCP will be divided into three sections. Youth Roundtable Discussions will bring youth together to discuss issues affecting the Polar Regions and potential solutions to these. A Young Researchers Conference will provide the opportunity for young researchers working in the Polar Regions to present their work to an interdisciplinary audience. The Polar Fair will provide an interactive environment for youth to learn about the Polar Regions. The IYCP will be of great importance to the IPY because it will serve as the principle venue during the Polar Year where youth from many different disciplines, backgrounds and countries will

  11. Hearing loss

    Science.gov (United States)

    Decreased hearing; Deafness; Loss of hearing; Conductive hearing loss; Sensorineural hearing loss; Presbycusis ... Conductive hearing loss (CHL) occurs because of a mechanical problem in the outer or middle ear. This may be ...

  12. Efficacy of the lithotripsy in treating lower pole renal stones.

    Science.gov (United States)

    Cui, Helen; Thomee, Eeke; Noble, Jeremy G; Reynard, John M; Turney, Benjamin W

    2013-06-01

    Use of extracorporeal lithotripsy is declining in North America and many European countries despite international guidelines advocating it as a first-line therapy. Traditionally, lithotripsy is thought to have poor efficacy at treating lower pole renal stones. We evaluated the success rates of lithotripsy for lower pole renal stones in our unit. 50 patients with lower pole kidney stones ≤15 mm treated between 3/5/11 and 19/4/12 were included in the study. Patients received lithotripsy on a fixed-site Storz Modulith SLX F2 lithotripter according to a standard protocol. Clinical success was defined as stone-free status or asymptomatic clinically insignificant residual fragments (CIRFs) ≤3 mm at radiological follow-up. The mean stone size was 7.8 mm. The majority of stones (66 %) were between 5 and 10 mm. 28 % of stones were between 10 and 15 mm. For solitary lower pole stones complete stone clearance was achieved in 63 %. Total stone clearance including those with CIRFs was achieved in 81 % of patients. As expected, for those with multiple lower pole stones the success rates were lower: complete clearance was observed in 39 % and combined clearance including those with CIRFs was 56 %. Overall, complete stone clearance was observed in 54 % of patients and clearance with CIRFs was achieved in 72 % of patients. Success rate could not be attributed to age, stone size or gender. Our outcome data for the treatment of lower pole renal stones (≤15 mm) compare favourably with the literature. With this level of stone clearance, a non-invasive, outpatient-based treatment like lithotripsy should remain the first-line treatment option for lower pole stones. Ureteroscopy must prove that it is significantly better either in terms of clinical outcome or patient satisfaction to justify replacing lithotripsy.

  13. Optimal pole shifting controller for interconnected power system

    International Nuclear Information System (INIS)

    Yousef, Ali M.; Kassem, Ahmed M.

    2011-01-01

    Research highlights: → Mathematical model represents a power system which consists of synchronous machine connected to infinite bus through transmission line. → Power system stabilizer was designed based on optimal pole shifting controller. → The system performances was tested through load disturbances at different operating conditions. → The system performance with the proposed optimal pole shifting controller is compared with the conventional pole placement controller. → The digital simulation results indicated that the proposed controller has a superior performance. -- Abstract: Power system stabilizer based on optimal pole shifting is proposed. An approach for shifting the real parts of the open-loop poles to any desired positions while preserving the imaginary parts is presented. In each step of this approach, it is required to solve a first-order or a second-order linear matrix Lyapunov equation for shifting one real pole or two complex conjugate poles, respectively. This presented method yields a solution, which is optimal with respect to a quadratic performance index. The attractive feature of this method is that it enables solutions of the complex problem to be easily found without solving any non-linear algebraic Riccati equation. The present power system stabilizer is based on Riccati equation approach. The control law depends on finding the feedback gain matrix, and then the control signal is synthesized by multiplying the state variables of the power system with determined gain matrix. The gain matrix is calculated one time only, and it works over wide range of operating conditions. To validate the power of the proposed PSS, a linearized model of a simple power system consisted of a single synchronous machine connected to infinite bus bar through transmission line is simulated. The studied power system is subjected to various operating points and power system parameters changes.

  14. Analysis of car’s frontal collision against pole

    Science.gov (United States)

    Ispas, N.; Nastasoiu, M.

    2017-10-01

    Reducing the effects of traffic accidents over the occupants is a major objective of collision attempts. Impacts between the car and the pole are very dangerous for the physical integrity of the car’s occupants. To minimalize the effects of such events on the passengers of a vehicle, a whole series of efforts by both designers and experienced engineers led to increasingly the vehicles safety. The main aim of these paper is to quantify the influences over the car passengers of loads involved by car against pole collisions using the same car model at different speeds. Also, this kind on occupant influences were study using a small car model. Other goal of the paper was the study of the cars stiffness in frontal collision against the pole. The paper’s experimental results were obtained by support of DSD, Dr. Steffan Datentechnik GmbH - Linz, Austria. The described tests were performed in full test facility of DSD Linz, in “Easter 2016 PC-Crash Seminar”. Cars accelerations, velocities, rotations angles after pole impact were registered and discussed. The novelty of the paper consists in studies referred for the same car model involved in car against pole collisions at different impact speeds. Paper’s conclusions can be future used for car safety improvement.

  15. Poles in the Dutch Cape Colony 1652-1814

    Directory of Open Access Journals (Sweden)

    Kowalski Mariusz

    2015-06-01

    Full Text Available The contribution of Poles to the colonisation and development of the Dutch Cape Colony is not commonly known. Yet, Poles have been appearing in this colony since its very inception (1652. During the entire period considered here the presence of Poles was the result of the strong economic ties between Poland and the Netherlands. At the end of this period there was an increase in their share, in connection with the presence of numerous alien military units on the territory of the Colony, because of Poles having served in these units. Numerous newcomers from Poland settled in South Africa for good, established families, and their progeny made up part of the local society. The evidence of this phenomenon is provided by the present-day Afrikaner families of, for instance, Drotsky, Kitshoff, Kolesky, Latsky, Masuriek, Troskie, Zowitsky, and others. A quite superficial estimation implies that the settlers coming from Poland could make up a bit over 1% of the ancestors of the present-day Afrikaners. Poles would also participate in the pioneering undertakings within the far-off fringes of the Colony, including the robbery-and-trade expedition of 1702.

  16. Assessment of Pole Erosion in a Magnetically Shielded Hall Thruster

    Science.gov (United States)

    Mikellides, Ioannis G.; Ortega, Alejandro L.

    2014-01-01

    Numerical simulations of a 6-kW laboratory Hall thruster called H6 have been performed to quantify the erosion rate at the inner pole. The assessments have been made in two versions of the thruster, namely the unshielded (H6US) and magnetically shielded (H6MS) configurations. The simulations have been performed with the 2-D axisymmetric code Hall2De which employs a new multi-fluid ion algorithm to capture the presence of low-energy ions in the vicinity of the poles. It is found that the maximum computed erosion rate at the inner pole of the H6MS exceeds the measured rate of back-sputtered deposits by 4.5 times. This explains only part of the surface roughening that was observed after a 150-h wear test, which covered most of the pole area exposed to the plasma. For the majority of the pole surface the computed erosion rates are found to be below the back-sputter rate and comparable to those in the H6US which exhibited little to no sputtering in previous tests. Possible explanations for the discrepancy are discussed.

  17. Familiar face + novel face = familiar face? Representational bias in the perception of morphed faces in chimpanzees

    Directory of Open Access Journals (Sweden)

    Yoshi-Taka Matsuda

    2016-08-01

    Full Text Available Highly social animals possess a well-developed ability to distinguish the faces of familiar from novel conspecifics to induce distinct behaviors for maintaining society. However, the behaviors of animals when they encounter ambiguous faces of familiar yet novel conspecifics, e.g., strangers with faces resembling known individuals, have not been well characterised. Using a morphing technique and preferential-looking paradigm, we address this question via the chimpanzee’s facial–recognition abilities. We presented eight subjects with three types of stimuli: (1 familiar faces, (2 novel faces and (3 intermediate morphed faces that were 50% familiar and 50% novel faces of conspecifics. We found that chimpanzees spent more time looking at novel faces and scanned novel faces more extensively than familiar or intermediate faces. Interestingly, chimpanzees looked at intermediate faces in a manner similar to familiar faces with regards to the fixation duration, fixation count, and saccade length for facial scanning, even though the participant was encountering the intermediate faces for the first time. We excluded the possibility that subjects merely detected and avoided traces of morphing in the intermediate faces. These findings suggest a bias for a feeling-of-familiarity that chimpanzees perceive familiarity with an intermediate face by detecting traces of a known individual, as 50% alternation is sufficient to perceive familiarity.

  18. Experimental measurement of lattice strain pole figures using synchrotron x rays

    International Nuclear Information System (INIS)

    Miller, M.P.; Bernier, J.V.; Park, J.-S.; Kazimirov, A.

    2005-01-01

    This article describes a system for mechanically loading test specimens in situ for the determination of lattice strain pole figures and their evolution in multiphase alloys via powder diffraction. The data from these experiments provide insight into the three-dimensional mechanical response of a polycrystalline aggregate and represent an extremely powerful material model validation tool. Relatively thin (0.5 mm) iron/copper specimens were axially strained using a mechanical loading frame beyond the macroscopic yield strength of the material. The loading was halted at multiple points during the deformation to conduct a diffraction experiment using a 0.5x0.5 mm 2 monochromatic (50 keV) x ray beam. Entire Debye rings of data were collected for multiple lattice planes ({hkl}'s) in both copper and iron using an online image plate detector. Strain pole figures were constructed by rotating the loading frame about the specimen transverse direction. Ideal powder patterns were superimposed on each image for the purpose of geometric correction. The chosen reference material was cerium (IV) oxide powder, which was spread in a thin layer on the downstream face of the specimen using petroleum jelly to prevent any mechanical coupling. Implementation of the system at the A2 experimental station at the Cornell High Energy Synchrotron Source (CHESS) is described. The diffraction moduli measured at CHESS were shown to compare favorably to in situ data from neutron-diffraction experiments conducted on the same alloys

  19. Electromagnetic Radial Forces in a Hybrid Eight-Stator-Pole, Six-Rotor-Pole Bearingless Switched-Reluctance Motor

    Science.gov (United States)

    Morrison, Carlos R.; Siebert, Mark W.; Ho, Eric J.

    2007-01-01

    Analysis and experimental measurement of the electromagnet force loads on the hybrid rotor in a novel bearingless switched-reluctance motor (BSRM) have been performed. A BSRM has the combined characteristics of a switched-reluctance motor and a magnetic bearing. The BSRM has an eight-pole stator and a six-pole hybrid rotor, which is composed of circular and scalloped lamination segments. The hybrid rotor is levitated using only one set of stator poles. A second set of stator poles imparts torque to the scalloped portion of the rotor, which is driven in a traditional switched reluctance manner by a processor. Analysis was done for nonrotating rotor poles that were oriented to achieve maximum and minimum radial force loads on the rotor. The objective is to assess whether simple one-dimensional magnetic circuit analysis is sufficient for preliminary evaluation of this machine, which may exhibit strong three-dimensional electromagnetic field behavior. Two magnetic circuit geometries, approximating the complex topology of the magnetic fields in and around the hybrid rotor, were employed in formulating the electromagnetic radial force equations. Reasonable agreement between the experimental results and the theoretical predictions was obtained with typical magnetic bearing derating factors applied to the predictions.

  20. Traumatic amputation of the left lower renal pole in children

    Energy Technology Data Exchange (ETDEWEB)

    Waxman, J.; Belman, A.B.; Kass, E.J.

    1985-07-01

    Four children between 5 and 10 years old suffered traumatic amputation of the left lower renal pole following flank trauma. All patients were evaluated with excretory urography and isotope renography. The renal scan clearly demonstrated failure of perfusion of the lower renal pole and urinary extravasation, and was believed to be more valuable than the standard excretory urogram as a diagnostic tool. All children were managed similarly: delayed (72 to 96 hours) exploration, simple removal of the amputated segment and insertion of a Penrose drain. They all have done well. The patients were normotensive at followup and had excellent function of the remaining portion of the kidney.

  1. Multiobjective H2/H? Control Design with Regional Pole Constraints

    Directory of Open Access Journals (Sweden)

    Junaidi Junaidi

    2012-03-01

    Full Text Available This paper presents multiobjective H2/H? control design with regional pole constraints. The state feedback gain can be obtained by solving a linear matrix inequality (LMI feasibility problem that robustly assigns the closed-loop poles in a prescribed LMI region. The proposed technique is illustrated with applications to the design of stabilizer for a typical single-machine infinite-bus (SMIB power system. The LMI-based control ensures adequate damping for widely varying system operating conditions. The simulation results illustrate the effectiveness and robustness of the proposed stabilizer.

  2. Induction Motor with Switchable Number of Poles and Toroidal Winding

    Directory of Open Access Journals (Sweden)

    MUNTEANU, A.

    2011-05-01

    Full Text Available This paper presents a study of an induction motor provided with toroidal stator winding. The ring-type coils offer a higher versatility in obtaining a different number of pole pairs by means of delta/star and series/parallel connections respectively. As consequence, the developed torque can vary within large limits and the motor can be utilized for applications that require, for example, high load torque values for a short time. The study involves experimental tests and FEM simulation for an induction machine with three configurations of pole pairs. The conclusions attest the superiority of the toroidal winding for certain applications such as electric vehicles or lifting machines.

  3. Challenges of Rover Navigation at the Lunar Poles

    Science.gov (United States)

    Nefian, Ara; Deans, Matt; Bouyssounouse, Xavier; Edwards, Larry; Dille, Michael; Fong, Terry; Colaprete, Tony; Miller, Scott; Vaughan, Ryan; Andrews, Dan; hide

    2015-01-01

    Observations from Lunar Prospector, LCROSS, Lunar Reconnaissance Orbiter (LRO), and other missions have contributed evidence that water and other volatiles exist at the lunar poles in permanently shadowed regions. Combining a surface rover and a volatile prospecting and analysis payload would enable the detection and characterization of volatiles in terms of nature, abundance, and distribution. This knowledge could have impact on planetary science, in-situ resource utilization, and human exploration of space. While Lunar equatorial regions of the Moon have been explored by manned (Apollo) and robotic missions (Lunokhod, Cheng'e), no surface mission has reached the lunar poles.

  4. Pedagogický odkaz Ivana Poledňáka

    OpenAIRE

    Čižinská, Klára

    2017-01-01

    The bachelor thesis covers the personality of Ivan Poledňák and his music-teaching heritage. In the first part his life, his activities in musical educational organizations and teaching at universities in the Czech Republic are described. In the second part his musical pedagogical publications are analysed. The aim of this thesis is to punctuate to his big contribution in music education. KEYWORDS Ivan Poledňák, Musically pedagogical inventiveness, Music-school-tomorrow, 40 radio lectures of ...

  5. Poles Living in Ireland and their Quality of Life

    Directory of Open Access Journals (Sweden)

    Agnieszka NOLKA

    2009-05-01

    Full Text Available The economic growth of Ireland resulted in a significant number of Poles migrating to Ireland following the EU enlargement in 2004. The article explores the quality of life of Poles living in Ireland. Using data from a preliminary survey conducted in 2006, several dimensions of living conditions are analysed, including interpersonal relations, material security, health and healthcare. The study shows that evaluations of almost all aspects of quality of life improved, apart from components such as healthcare and the ability to acquire help from social organisations. Also interpersonal relations, contrary to the initial assumption, were enhanced by migration to Ireland.

  6. Is it possible to reduce the knee joint compression force during level walking with hiking poles?

    DEFF Research Database (Denmark)

    Jensen, S B; Henriksen, M; Aaboe, J

    2010-01-01

    Walking with hiking poles has become a popular way of exercising. Walking with poles is advocated as a physical activity that significantly reduces the loading of the hip, knee and ankle joints. We have previously observed that pole walking does not lead to a reduction of the load on the knee joint....... However, it is unclear whether an increased force transmitted through the poles can reduce the load on the knee joint. Thus, the purpose of the present study was to investigate if an increased load transmitted through the arms to the poles could reduce the knee joint compression force during level walking...... with poles. We hypothesized that an increased pole force would result in a reduction of the knee joint compression force. Gait analyses from 10 healthy subjects walking with poles were obtained. The pole force was measured simultaneously during the gait analyses. The knee joint compression forces were...

  7. From 'third pole' to north pole: a Himalayan origin for the arctic fox.

    Science.gov (United States)

    Wang, Xiaoming; Tseng, Zhijie Jack; Li, Qiang; Takeuchi, Gary T; Xie, Guangpu

    2014-07-22

    The 'third pole' of the world is a fitting metaphor for the Himalayan-Tibetan Plateau, in allusion to its vast frozen terrain, rivalling the Arctic and Antarctic, at high altitude but low latitude. Living Tibetan and arctic mammals share adaptations to freezing temperatures such as long and thick winter fur in arctic muskox and Tibetan yak, and for carnivorans, a more predatory niche. Here, we report, to our knowledge, the first evolutionary link between an Early Pliocene (3.60-5.08 Myr ago) fox, Vulpes qiuzhudingi new species, from the Himalaya (Zanda Basin) and Kunlun Mountain (Kunlun Pass Basin) and the modern arctic fox Vulpes lagopus in the polar region. A highly hypercarnivorous dentition of the new fox bears a striking resemblance to that of V. lagopus and substantially predates the previous oldest records of the arctic fox by 3-4 Myr. The low latitude, high-altitude Tibetan Plateau is separated from the nearest modern arctic fox geographical range by at least 2000 km. The apparent connection between an ancestral high-elevation species and its modern polar descendant is consistent with our 'Out-of-Tibet' hypothesis postulating that high-altitude Tibet was a training ground for cold-environment adaptations well before the start of the Ice Age. © 2014 The Author(s) Published by the Royal Society. All rights reserved.

  8. Internal fixation of displaced inferior pole of the patella fractures using vertical wiring augmented with Krachow suturing.

    Science.gov (United States)

    Oh, Hyoung-Keun; Choo, Suk-Kyu; Kim, Ji-Wan; Lee, Mark

    2015-12-01

    We present the surgical technique of separate vertical wiring for displaced inferior pole fractures of the patella combined with Krachow suture and report the surgical outcomes. Between September 2007 to May 2012, 11 consecutive patients (mean age, 54.6 years) with inferior pole fractures of the patella (AO/OTA 34-A1) were retrospectively enrolled in this study. Through longitudinal incision, all patients underwent open reduction and internal fixation by separate vertical wiring combined with Krackow suture. The range of motion, loss of fixation, and Bostman score were primary outcome measures. The union time was 10 weeks after surgery on average (range: 8-12). No patient had nonunion, loss of reduction and wire breakage. There was no case of wound problem and irritation from the implant. At final follow-up, the average range of motion arc was 129.4° (range: 120-140). The mean Bostman score at last follow-up was 29.6 points (range: 28-30) and graded excellent in all cases. Separate vertical wiring combined with Krackow suture for inferior pole fractures of the patella is a useful technique that is easy to perform and can provide stable fixation with excellent results in knee function. Copyright © 2015 Elsevier Ltd. All rights reserved.

  9. Head and face reconstruction

    Science.gov (United States)

    ... this page: //medlineplus.gov/ency/article/002980.htm Head and face reconstruction To use the sharing features on this page, please enable JavaScript. Head and face reconstruction is surgery to repair or ...

  10. Face Detection and Recognition

    National Research Council Canada - National Science Library

    Jain, Anil K

    2004-01-01

    .... Specifically, the report addresses the problem of detecting faces in color images in the presence of various lighting conditions and complex backgrounds as well as recognizing faces under variations...

  11. Plotter of pole figure using data from x-ray diffraction

    International Nuclear Information System (INIS)

    Lima, A.F.

    1990-01-01

    Any polycrystalline aggregate normally has a preferred crystallographic orientation, or texture which depends on its thermal and or mechanical history. Preferred orientation is best described by means of a pole figure. A pole figure is a stereographic projection which shows the variation in pole density with pole orientation, for a selected set of crystal planes. In this work, computer programs was developed to plot pole figures. The corrected intensities are calculated and directly transmitted to the plotter. The different intensities levels are represented by different colors in the pole figure. (author)

  12. Liz Taylor : minu van Gogh pole natsidele kuulunud

    Index Scriptorium Estoniae

    2004-01-01

    Elizabeth Taylor palus kohtult otsust, et talle kuuluvat 15 miljonit dollarit maksvat Vincent van Goghi maali "Vaade Saint-Remy varjupaigale" pole natsid Margarete Mauthneri juudiperekonna käest vägivaldselt ära võtnud. E. Taylori isa ostis maali 1963. a. Londonis oksjonilt

  13. Analytical signal and reduction to pole in the interpretation of ...

    African Journals Online (AJOL)

    Analytical signal and reduction to pole in the interpretation of aeromagnetic data at low magnetic latitudes: a case study of the middle Benue trough, Nigeria. OK Likkason. Abstract. No Abstract. Global Journal of Geological Sciences Vol. 4(1) 2006: 29-38. Full Text: EMAIL FULL TEXT EMAIL FULL TEXT · DOWNLOAD FULL ...

  14. Finite element analysis of boron diffusion in wooden Poles

    DEFF Research Database (Denmark)

    Krabbenhøft, Kristian; Hoffmeyer, Preben; Bechgaard, Carl

    2004-01-01

    The problem of describing the migration of dissolved boron in wood is treated with special reference to the commonly used remedial treatment of wooden poles. The governing equations are derived and discussed together with some of the material parameters required. The equations are solved...

  15. Probability models of the x, y pole coordinates data

    Science.gov (United States)

    Sen, A.; Niedzielski, T.; Kosek, W.

    2008-12-01

    The aim of this study is to find the most appropriate probabilistic model for the x, y pole coordinates time series. We have analyzed the IERS eopc04_05 data set covering the period 1962 - 2008. We have also considered the residual x, y pole coordinate time series, which is computed as the difference between the original data and the corresponding least-squares model of the Chandler circle and annual ellipse. Using the measures of skewness and kurtosis of the empirical distribution of the data, we find that the x, y pole coordinates and the corresponding residuals time series cannot be modeled by a normal (Gaussian) distribution. A normal distribution has zero skewness and a kurtosis value of 3. We have fitted several non- Gaussian distributions to the datasets. They include the Generalized Extreme Value distribution, 4-parameter Beta distribution, Johnson SB and SU distributions, Generalized Pareto distribution and Wakeby distribution. Suitability of these distributions as probabilistic models for the x, y pole coordinates and the corresponding residuals time series are discussed.

  16. Bacterial diversity in snow on North Pole ice floes

    DEFF Research Database (Denmark)

    Hauptmann, Aviaja Zenia Edna Lyberth; Stibal, Marek; Bælum, Jacob

    2014-01-01

    The microbial abundance and diversity in snow on ice floes at three sites near the North Pole was assessed using quantitative PCR and 454 pyrosequencing. Abundance of 16S rRNA genes in the samples ranged between 43 and 248 gene copies per millilitre of melted snow. A total of 291,331 sequences we...

  17. Particles as S-matrix poles: hadron democracy

    International Nuclear Information System (INIS)

    Chew, G.F.

    1989-01-01

    The connection between two theoretical ideas of the 1950s is traced in this article, namely that hadrons are nonfundamental, ''composite'' particles and that all physically observable particles correspond to singularities of an analytic scattering matrix. The S matrix theory developed by Werner Heisenberg in the early forties now incorporated the concepts of unitarity, invariance, analyticity and causality. The meson-exchange force meant that poles must be present in nucleon-nuclear and pion-nucleon scattering as predicted by dispersion relations. Experimental work in accessible regions determined pole residues. Pole residue became associated with force strength and pole position with particle mass. In 1959, the author discovered the so-called ''bootstrap'' theory the rho meson as a force generates a rho particle. By the end of the 1950s it was clear that all hadrons had equal status, each being bound states of other hadrons, sustained by hadron exchange forces and that hadrons are self-generated by an S-matrix bootstrap mechanism that determines all their properties. (UK)

  18. Finite Element Analysis of Boron Diffusion in Wooden Poles

    DEFF Research Database (Denmark)

    Krabbenhøft, Kristian; Hoffmeyer, P.; Bechgaard, C.

    2003-01-01

    The problem of describing the migration of dissolved boron in wood is treated with special reference to the commonly used remedial treatment of wooden poles. The governing equations are derived and discussed together with some of the material parameters required. The equations are solved by the f...... by the finite element method and, finally, results showing the effect of different treatment strategies are presented....

  19. Finite element analysis of boron diffusion in wooden Poles

    DEFF Research Database (Denmark)

    Krabbenhøft, Kristian; Hoffmeyer, Preben; Bechgaard, Carl

    2004-01-01

    The problem of describing the migration of dissolved boron in wood is treated with special reference to the commonly used remedial treatment of wooden poles. The governing equations are derived and discussed together with some of the material parameters required. The equations are solved by the f...... by the finite element method and, finally, results showing the effect of different treatment strategies are presented....

  20. Finite Element Analysis of Boron Diffusion in Wooden Poles

    DEFF Research Database (Denmark)

    Krabbenhøft, Kristian; Hoffmeyer, Preben; Bechgaard, Carl

    2004-01-01

    The problem of describing the migration of dissolved boron in wood is treated with special reference to the commonly used remedial treatment of wooden poles. The governing equations are derived and discussed together with some of the material parameters required. The equations are solved by the f...... by the finite element method and, finally, results showing the effect of different treatment strategies are presented....

  1. Separable pole expansions in four-nucleon bound state calculations

    International Nuclear Information System (INIS)

    Sofianos, S.A.; Fiedeldey, H.; Haberzettl, H.; Sandhas, W.

    1982-04-01

    We compare the utility of the Generalized Unitary Pole Expansion (GUPE) and the Energy-Dependent Pole Expansion (EDPE) for the three-body subsystem amplitudes in four-body state calculations for a variety of separable and local nucleon-nucleon interactions. It is found that, with the EDPE, the four-body binding energy is well reproduced with only two terms each for the (2+2)- and the (3+1)-subsystem, respectively, while the GUPE requires three terms for the (3+1)-channel and four terms for the (2+2)-channel. We thus conclude that pole dominance is of greater importance for the GUPE than for EDPE, which works equally well for both types of subsystems. It is found that both methods, in particular the EDPE, converge more rapidly with increasing repulsion in the two-body interaction, i.e. the more realistic the interaction becomes. Both expansions require similar computing times for a converged calculation and are about 15-20 times faster than the widely used Hilbert-Schmidt Expansion (HSE). The respective merits of the two pole expansions are discussed and compared with the HSE. (orig.)

  2. USA valitsus: Tallinna linnahalli miljardigarantiid pole olemas / Raimo Poom

    Index Scriptorium Estoniae

    Poom, Raimo

    2010-01-01

    USA Eesti-saatkonna teatel pole USA valitsus andnud garantiid mitte ühelegi projektile Tallinnas. Tallinna abilinnapea Taavi Aasa sõnul ei saa USA garantiist teha juttu enne, kui Eesti valitsus selle omakorda garanteerib. Taavi Aasa kirjast rahandusminister Jürgen Ligile

  3. An estimate on the purely imaginary poles of scattering matrix

    International Nuclear Information System (INIS)

    Bozhkov, Y.D.

    1988-12-01

    In this work we obtain two estimates (upper and lower) on the number of purely imaginary poles of the scattering matrix for the wave equation in the exterior of a compact smooth obstacle in R n , n ≥ 3 odd. The method of Lax and Phillips is used. (author). 5 refs

  4. Kick, Glide, Pole! Cross-Country Skiing Fun (Part II)

    Science.gov (United States)

    Duoos, Bridget A.

    2012-01-01

    Part I of Kick, Glide, Pole! Cross-Country Skiing Fun, which was published in last issue, discussed how to select cross-country ski equipment, dress for the activity and the biomechanics of the diagonal stride. Part II focuses on teaching the diagonal stride technique and begins with a progression of indoor activities. Incorporating this fun,…

  5. Catapult effect in pole vaulting: is muscle coordination determinant?

    Science.gov (United States)

    Frère, Julien; Göpfert, Beat; Hug, François; Slawinski, Jean; Tourny-Chollet, Claire

    2012-02-01

    This study focused on the phase between the time of straightened pole and the maximum height (HP) of vaulter and aimed at determining the catapult effect in pole vaulting on HP. Seven experienced vaulters performed 5-10 vaults recorded by two video cameras, while the surface electromyography (sEMG) activity of 10 upper limbs muscles was recorded. HP was compared with an estimated maximum height (HP(est)) allowing the computation of a push-off index. Muscle synergies were extracted from the sEMG activity profiles using a non-negative matrix factorization algorithm. No significant difference (p>0.47) was found between HP(est) (4.64±0.21m) and HP (4.69±0.23m). Despite a high inter-individual variability in sEMG profiles, two muscle synergies were extracted for all the subjects which accounted for 96.1±2.9% of the total variance. While, the synergy activation coefficients were very similar across subjects, a higher variability was found in the muscle synergy vectors. Consequently, whatever the push-off index among the pole vaulters, the athletes used different muscle groupings (i.e., muscle synergy vectors) which were activated in a similar fashion (i.e., synergy activation coefficients). Overall, these results suggested that muscle coordination adopted between the time of straightened pole and the maximum height does not have a major influence on HP. Copyright © 2011 Elsevier Ltd. All rights reserved.

  6. Pole solution in six dimensions as a dimensional reduction model

    Science.gov (United States)

    Ichinose, Shoichi

    2002-01-01

    A solution with the pole configuration in six dimensions is analyzed. It is a dimensional reduction model of Randall-Sundrum type. The soliton configuration is induced by the bulk Higgs mechanism. The boundary condition is systematically solved up to the 6th order. The Riemann curvature is finite everywhere.

  7. Diplodia natalensis , Pole Evans: a causal agent of citrus gummosis ...

    African Journals Online (AJOL)

    Isolations were made from the barks of gummosis-infected citrus trees from orchards of the University of Ghana Agricultural Research Station at Kade. The isolation media used were 1.5% water agar, 1.5% water agar + nystatin and 1.5% water agar + benomyl. Four isolates including Diplodia natalensis Pole Evans, ...

  8. Poled-glass devices: Influence of surfaces and interfaces

    DEFF Research Database (Denmark)

    Fage-Pedersen, Jacob; Jacobsen, Rune Shim; Kristensen, Martin

    2007-01-01

    Devices in periodically poled glass must have a large periodic variation of the built-in field. We show that the periodic variation can be severely degraded by charge dynamics taking place at the external (glass–air) interface or at internal (glass–glass) interfaces if the interfaces have imperfe...

  9. BMP regulates vegetal pole induction centres in early xenopus development.

    Science.gov (United States)

    Nachaliel, N; Re'Em-Kalma, Y; Eshed, O; Elias, S; Frank, D

    1998-10-01

    Bone morphogenetic protein (BMP) plays an important role in mesoderm patterning in Xenopus. The ectopic expression of BMP-4 protein hyperventralizes embryos, whereas embryos expressing a BMP-2/4 dominant-negative receptor (DNR) are hyperdorsalized. Mesoderm is initially induced in the marginal zone by cells in the underlying vegetal pole. While much is known about BMP's expression and role in patterning the marginal zone, little is known about its early role in regulating vegetal mesoderm induction centre formation. The role of BMP in regulating formation of vegetal mesoderm inducing centres during early Xenopus development was examined. Ectopic BMP-4 expression in vegetal pole cells inhibited dorsal mesoderm induction but increased ventral mesoderm induction when recombined with animal cap ectoderm in Nieuwkoop explants. 32-cell embryos injected with BMP-4 RNA in the most vegetal blastomere tier were not hyperdorsalized by LiCl treatment. The ectopic expression of Smad or Mix.1 proteins in the vegetal pole also inhibited dorsal mesoderm induction in explants and embryos. Expression of the BMP 2/4 DNR in the vegetal pole increased dorsal mesoderm induction and inhibited ventral mesoderm induction in explants and embryos. These results support a role for BMP signalling in regulating ventral vegetal and dorsal vegetal mesoderm induction centre formation during early Xenopus development.

  10. Carrier Phase GPS Navigation to the North Pole

    Science.gov (United States)

    Moore, T.; Roberts, G. W.

    Over the last few years, on-the-fly integer ambiguity resolution for GPS has proven to be successful over short baselines (500 km. New techniques have been developed at the University of Nottingham to allow very long baseline integer ambiguity resolution, on-the-fly. A major problem with the use of carrier phase data is that posed by cycle slips. A technique for detecting and correcting cycle slips has been developed, and its use is discussed in this paper. The new technique has been proven through a series of trials, one of which included two flights to the North Pole, performing centimetric level positioning all the way to the pole. For many years, the GD Aero-Systems Course of the Air Warfare Centre based at RAF Cranwell executed a series of equipment flight trials to the North Pole, called the ARIES Flights. In May 1996, the authors were fortunate to take part in both flights, via Iceland and Greenland, to the North Pole. Based on reference stations at Thule Air Base, integer ambiguity resolution was accomplished, on-the-fly, and centimetric level navigation maintained throughout the flights. Earlier trials detailed in the paper demonstrate that the technique can resolve integer ambiguities on-the-fly within a few seconds over a baseline length of approximately 134 km, resulting in an accuracy of 12 cm. The majority of the residual error source for this being the ionosphere.

  11. Different temperature and cooling patterns at the blunt and sharp egg poles reflect the arrangement of eggs in an avian clutch.

    Science.gov (United States)

    Šálek, Miroslav E; Zárybnická, Markéta

    2015-01-01

    Incubation is an energetically demanding process during which birds apply heat to their eggs to ensure embryonic development. Parent behaviours such as egg turning and exchanging the outer and central eggs in the nest cup affect the amount of heat lost to the environment from individual eggs. Little is known, however, about whether and how egg surface temperature and cooling rates vary among the different areas of an egg and how the arrangement of eggs within the clutch influences heat loss. We performed laboratory (using Japanese quail eggs) and field (with northern lapwing eggs) experiments using infrared imaging to assess the temperature and cooling patterns of heated eggs and clutches. We found that (i) the sharp poles of individual quail eggs warmed to a higher egg surface temperature than did the blunt poles, resulting in faster cooling at the sharp poles compared to the blunt poles; (ii) both quail and lapwing clutches with the sharp poles oriented towards the clutch centre (arranged clutches) maintained higher temperatures over the central part of the clutch than occurred in those clutches where most of the sharp egg poles were oriented towards the exterior (scattered clutches); and (iii) the arranged clutches of both quail and lapwing showed slower cooling rates at both the inner and outer clutch positions than did the respective parts of scattered clutches. Our results demonstrate that egg surface temperature and cooling rates differ between the sharp and blunt poles of the egg and that the orientation of individual eggs within the nest cup can significantly affect cooling of the clutch as a whole. We suggest that birds can arrange their eggs within the nest cup to optimise thermoregulation of the clutch.

  12. Predicting Interactions between Common Dolphins and the Pole-and-Line Tuna Fishery in the Azores.

    Science.gov (United States)

    Cruz, Maria João; Menezes, Gui; Machete, Miguel; Silva, Mónica A

    2016-01-01

    Common dolphins (Delphinus delphis) are responsible for the large majority of interactions with the pole-and-line tuna fishery in the Azores but the underlying drivers remain poorly understood. In this study we investigate the influence of various environmental and fisheries-related factors in promoting the interaction of common dolphins with this fishery and estimate the resultant catch losses. We analysed 15 years of fishery and cetacean interaction data (1998-2012) collected by observers placed aboard tuna fishing vessels. Dolphins interacted in less than 3% of the fishing events observed during the study period. The probability of dolphin interaction varied significantly between years with no evident trend over time. Generalized additive modeling results suggest that fishing duration, sea surface temperature and prey abundance in the region were the most important factors explaining common dolphin interaction. Dolphin interaction had no impact on the catches of albacore, skipjack and yellowfin tuna but resulted in significantly lower catches of bigeye tuna, with a predicted median annual loss of 13.5% in the number of fish captured. However, impact on bigeye catches varied considerably both by year and fishing area. Our work shows that rates of common dolphin interaction with the pole-and-line tuna fishery in the Azores are low and showed no signs of increase over the study period. Although overall economic impact was low, the interaction may lead to significant losses in some years. These findings emphasize the need for continued monitoring and for further research into the consequences and economic viability of potential mitigation measures.

  13. Predicting Interactions between Common Dolphins and the Pole-and-Line Tuna Fishery in the Azores.

    Directory of Open Access Journals (Sweden)

    Maria João Cruz

    Full Text Available Common dolphins (Delphinus delphis are responsible for the large majority of interactions with the pole-and-line tuna fishery in the Azores but the underlying drivers remain poorly understood. In this study we investigate the influence of various environmental and fisheries-related factors in promoting the interaction of common dolphins with this fishery and estimate the resultant catch losses. We analysed 15 years of fishery and cetacean interaction data (1998-2012 collected by observers placed aboard tuna fishing vessels. Dolphins interacted in less than 3% of the fishing events observed during the study period. The probability of dolphin interaction varied significantly between years with no evident trend over time. Generalized additive modeling results suggest that fishing duration, sea surface temperature and prey abundance in the region were the most important factors explaining common dolphin interaction. Dolphin interaction had no impact on the catches of albacore, skipjack and yellowfin tuna but resulted in significantly lower catches of bigeye tuna, with a predicted median annual loss of 13.5% in the number of fish captured. However, impact on bigeye catches varied considerably both by year and fishing area. Our work shows that rates of common dolphin interaction with the pole-and-line tuna fishery in the Azores are low and showed no signs of increase over the study period. Although overall economic impact was low, the interaction may lead to significant losses in some years. These findings emphasize the need for continued monitoring and for further research into the consequences and economic viability of potential mitigation measures.

  14. Predicting Interactions between Common Dolphins and the Pole-and-Line Tuna Fishery in the Azores

    Science.gov (United States)

    Cruz, Maria João; Menezes, Gui; Machete, Miguel; Silva, Mónica A.

    2016-01-01

    Common dolphins (Delphinus delphis) are responsible for the large majority of interactions with the pole-and-line tuna fishery in the Azores but the underlying drivers remain poorly understood. In this study we investigate the influence of various environmental and fisheries-related factors in promoting the interaction of common dolphins with this fishery and estimate the resultant catch losses. We analysed 15 years of fishery and cetacean interaction data (1998–2012) collected by observers placed aboard tuna fishing vessels. Dolphins interacted in less than 3% of the fishing events observed during the study period. The probability of dolphin interaction varied significantly between years with no evident trend over time. Generalized additive modeling results suggest that fishing duration, sea surface temperature and prey abundance in the region were the most important factors explaining common dolphin interaction. Dolphin interaction had no impact on the catches of albacore, skipjack and yellowfin tuna but resulted in significantly lower catches of bigeye tuna, with a predicted median annual loss of 13.5% in the number of fish captured. However, impact on bigeye catches varied considerably both by year and fishing area. Our work shows that rates of common dolphin interaction with the pole-and-line tuna fishery in the Azores are low and showed no signs of increase over the study period. Although overall economic impact was low, the interaction may lead to significant losses in some years. These findings emphasize the need for continued monitoring and for further research into the consequences and economic viability of potential mitigation measures. PMID:27851763

  15. Decay resistance of out-of-service utility poles as related to the distribution of residual creosote content

    Science.gov (United States)

    Han Roliadi; Chung Y. Hse; Elvin T. Choong; Todd F. Shupe

    2000-01-01

    Decay resistance of out-of-service poles was investigated to evaluate their effectiveness against biodegradation for possible recycling of these poles for composite products. Decay resistance was related to creosote content and creosote distribution in poles with service durations of 5 and 25 years and also freshly treated poles. Weathering of the poles had caused...

  16. Inferior patellar pole fragmentation in children: just a normal variant?

    Energy Technology Data Exchange (ETDEWEB)

    Kan, J.H.; Vogelius, Esben S.; Orth, Robert C.; Guillerman, R.P.; Jadhav, Siddharth P. [Texas Children' s Hospital, E.B. Singleton Pediatric Radiology, Houston, TX (United States)

    2015-06-15

    Fragmentary ossification of the inferior patella is often dismissed as a normal variant in children younger than 10 years of age. The purpose of this study was to determine whether fragmentary inferior patellar pole ossification is a normal variant or is associated with symptoms or signs of pathology using MRI and clinical exam findings as reference. A retrospective review was performed on 150 patients ages 5-10 years who underwent 164 knee radiography and MRI exams (45.1% male, mean age: 7.8 years). The presence or absence of inferior patellar pole fragmentation on radiography was correlated with the presence or absence of edema-like signal on MR images. Clinical notes were reviewed for the presence of symptoms or signs referable to the inferior patellar pole. These data were compared with a 1:1 age- and sex-matched control group without inferior pole fragmentation. Statistical analysis was performed using two-tailed t-tests. Forty of 164 (24.4%) knee radiographs showed fragmentary ossification of the inferior patella. Of these 40 knees, 62.5% (25/40) had edema-like signal of the inferior patellar bone marrow compared with 7.5% (3/40) of controls (P = 0.035). Patients with fragmentary ossification at the inferior patella had a significantly higher incidence of documented focal inferior patellar pain compared with controls (20% vs. 2.5%, P = 0.015). Inferior patellar pole fragmentation in children 5 to 10 years of age may be associated with localized symptoms and bone marrow edema-like signal and should not be routinely dismissed as a normal variant of ossification. (orig.)

  17. Bycatch in the Maldivian pole-and-line tuna fishery.

    Science.gov (United States)

    Miller, Kelsey I; Nadheeh, Ibrahim; Jauharee, A Riyaz; Anderson, R Charles; Adam, M Shiham

    2017-01-01

    Tropical tuna fisheries are among the largest worldwide, with some having significant bycatch issues. However, pole-and-line tuna fisheries are widely believed to have low bycatch rates, although these have rarely been quantified. The Maldives has an important pole-and-line fishery, targeting skipjack tuna (Katsuwonus pelamis). In the Maldives, 106 pole-and-line tuna fishing days were observed between August 2014 and November 2015. During 161 fishing events, tuna catches amounted to 147 t: 72% by weight was skipjack, 25% yellowfin tuna (Thunnus albacares) and 3% other tunas. Bycatch (all non-tuna species caught plus all tuna discards) amounted to 951 kg (0.65% of total tuna catch). Most of the bycatch (95%) was utilized, and some bycatch was released alive, so dead discards were particularly low (0.02% of total tuna catch, or 22 kg per 100 t). Rainbow runner (Elagatis bipinnulata) and dolphinfish (Coryphaena hippurus) together constituted 93% of the bycatch. Live releases included small numbers of silky sharks (Carcharhinus falciformis) and seabirds (noddies, Anous tenuirostris and A. stolidus). Pole-and-line tuna fishing was conducted on free schools and schools associated with various objects (Maldivian anchored fish aggregating devices [aFADs], drifting FADs from western Indian Ocean purse seine fisheries, other drifting objects and seamounts). Free school catches typically included a high proportion of large skipjack and significantly less bycatch. Associated schools produced more variable tuna catches and higher bycatch rates. Fishing trips in the south had significantly lower bycatch rates than those in the north. This study is the first to quantify bycatch rates in the Maldives pole-and-line tuna fishery and the influence of school association on catch composition. Ratio estimator methods suggest roughly 552.6 t of bycatch and 27.9 t of discards are caught annually in the fishery (based on 2015 national catch), much less than other Indian Ocean tuna

  18. Acute effects of flexible pole exercise on heart rate dynamics.

    Science.gov (United States)

    de Oliveira, Letícia Santana; Moreira, Patrícia S; Antonio, Ana M; Cardoso, Marco A; de Abreu, Luiz Carlos; Navega, Marcelo T; Raimundo, Rodrigo D; Valenti, Vitor E

    2015-01-01

    Exercise with flexible poles provides fast eccentric and concentric muscle contractions. Although the literature reports significant muscle chain activity during this exercise, it is not clear if a single bout of exercise induces cardiac changes. In this study we assessed the acute effects of flexible pole exercise on cardiac autonomic regulation. The study was performed on 22 women between 18 and 26 years old. We assessed heart rate variability (HRV) in the time (SDNN, RMSSD and pNN50) and frequency (HF, LF and LF/HF ratio) domains and geometric indices of HRV (RRTri, TINN, SD1, SD2 and SD1/SD2 ratio). The subjects remained at rest for 10 min and then performed the exercises with the flexible poles. Immediately after the exercise protocol, the volunteers remained seated at rest for 60 min and HRV was analyzed. We observed no significant changes in time domain (SDNN: p=0.72; RMSSD: p=0.94 and pNN50: p=0.92) or frequency domain indices (LF [nu]: p=0.98; LF [ms(2)]: p=0.72; HF [nu]: p=0.98; HF [ms(2)]: p=0.82 and LF/HF ratio: p=0.7) or in geometric indices (RRTri: p=0.54; TINN: p=0.77; SD1: p=0.94; SD2: p=0.67 and SD/SD2: p=0.42) before and after a single bout of flexible pole exercise. A single bout of flexible pole exercise did not induce significant changes in cardiac autonomic regulation in healthy women. Copyright © 2014 Sociedade Portuguesa de Cardiologia. Published by Elsevier España. All rights reserved.

  19. Wire inhomogeneity detector having a core with opposing pole pieces and guide pieces adjacent the opposing pole pieces

    International Nuclear Information System (INIS)

    Gibson, G.H.; Smits, R.G.; Eberhard, P.H.

    1989-01-01

    This patent describes a wire inhomogeneity detector assembly for detecting changes in the conductive properties of a wire as the wire is passed therethrough. It comprises: a coil assembly through which a wire containing conductive material is adapted to be pressed in a direction substantially perpendicular to a longitudinal axis of the coil assembly. The coil assembly comprising a single ferrite core having a pair of opposing pole pieces between which are an associated conductive wire to be tested is adapted to be passed, each of the pole pieces having a coil wound therearound. The coil assembly including a guide-block consisting of a pair of guide pieces mounted adjacent to ends of the opposing pole pieces for guiding an associated conductive wire between the pole pieces and for reducing stray magnetic field lines. The guide pieces being positioned closely adjacent an associated conductive wire passing therebetween; an impedance bridge adjusted to an null balance point operatively connected to the coil assembly which measures the impedance of the coil assembly and is unbalanced by changes in eddy currents generated in the coil assembly; and a filter detector alarm assembly operatively connected to an output of the impedance bridge. The filter detector alarm assembly including an input bandpass filter detector alarm assembly including an input bandpass filter operatively connected to a differential comparator, the output of which triggers an alarm

  20. Repair of impact damaged utility poles with fiber reinforced polymers (FRP), phase II : [summary].

    Science.gov (United States)

    2015-04-01

    The aluminum and steel utility poles which support traffic signals, lighting, or mast-arm signs : are vulnerable to collisions from vehicles because of proximity to roadways. Removing these : poles for repair is costly and time-consuming, and removal...

  1. Pole Shape Optimization of Permanent Magnet Synchronous Motors Using the Reduced Basis Technique

    Directory of Open Access Journals (Sweden)

    A. Jabbari

    2010-03-01

    Full Text Available In the present work, an integrated method of pole shape design optimization for reduction of torque pulsation components in permanent magnet synchronous motors is developed. A progressive design process is presented to find feasible optimal shapes. This method is applied on the pole shape optimization of two prototype permanent magnet synchronous motors, i.e., 4-poles/6-slots and 4-poles-12slots.

  2. [The splenic inferior pole of rats and hyperbaric oxygen].

    Science.gov (United States)

    Paulo, Isabel Cristina Andreatta Lemos; Paulo, Danilo Nagib Salomão; Ferrari, Thiago Antunes; Azeredo, Thiago Caetano Valadão de; Silva, Alcino Lázaro da

    2008-01-01

    To study the functional and morphological features of the lower pole of the spleen in rats submitted, or not, to postoperative hyperbaric oxygen therapy. Seventy-nine Wistar rats, weighing 248.7 +/- 27 g, divided into two groups [group A - simulation (n=40), group B - lower pole (n=39)] underwent surgery and were subdivided into two groups: 11 and 70 postoperative days. Each subgroup was subdivided into animals not treated (nt) (A11nt, n=10; B11nt, n=13; A70nt, n=10; B70nt, n=9) and treated with hyperbaric oxygen (t) (A11t, n=10; B11t, n=9; A70t, n=10; B70t, n=8). Blood was collected for measurement of lipids and immunoglobulins, platelet and Howell-Jolly body count before and after surgery. The spleen and lower pole were removed for histology. There was an increase of total cholesterol (p=0.002), VLDL-cholesterol and triglycerides (p=0.003) and of LDL-cholesterol (p=0.013) in subgroup B11nt, and no alterations were observed in the other subgroups. IgM decreased in subgroups B11t (p=0.007), B11nt (p=0.0000), B70nt (p=0.0005), B70t (p=0.02), and no change was observed in the simulation group. The number of platelets increased in subgroups B11nt (p=0.002) and B11t (p=0.01) and remained unchanged in the other subgroups. Howell-Jolly bodies were less numerous in subgroup B70nt than in subgroup B11nt (p=0.019). Lower pole viability was better in subgroup B11t than in B11nt and in subgroup B70 than in B11, and did not differ between subgroups B70t and B70nt. Function and viability of the remaining lower pole improved during the late postoperative period. Viability and function of the lower pole were better during the early but not during the late postoperative period, in animals submitted to hyperbaric oxygen therapy.

  3. Ocular posterior pole pathological modifications related to complicated pregnancy. A review.

    Science.gov (United States)

    Păun, Vanessa Andrada; Ionescu, Zamfir-Radu; Voinea, Liliana; Cîrstoiu, Monica; Baroș, Alexandru; Pricopie, Ștefan; Ciuluvică, Radu

    2017-01-01

    Ocular posterior pole modification are a pathological manifestation in complicated pregnancies, especially when pregnancy induced hypertension is present (PIH), as well as in preeclampsia (PE) or eclampsia. Nonetheless, as the pregnancy evolves, the possibility for an aggravated evolution with HELLP syndrome, disseminated intravascular coagulation, and idiopathic thrombocytopenic purpura may have an ocular manifestation that, mainly, implies a loss of visual field or acuity, that, left unattended, may constitute a permanent impairment. Pregestational conditions like pituitary adenoma or genetic pedigree for complement factor H gene (1q31.1) single nucleotide mutations could lead to central serous chorioretinopathy or retinal detachment with severe, ischemic, central cilioretinal artery or vein occlusion and optic nerve atrophy. Furthermore, although subtle in many cases, any new visual symptoms during pregnancy should constitute an alarming factor for obstetrical reevaluation and ophthalmological approach in order to preserve the mother's quality of life.

  4. All-Pole Recursive Digital Filters Design Based on Ultraspherical Polynomials

    Directory of Open Access Journals (Sweden)

    N. Stojanovic

    2014-09-01

    Full Text Available A simple method for approximation of all-pole recursive digital filters, directly in digital domain, is described. Transfer function of these filters, referred to as Ultraspherical filters, is controlled by order of the Ultraspherical polynomial, nu. Parameter nu, restricted to be a nonnegative real number (nu ≥ 0, controls ripple peaks in the passband of the magnitude response and enables a trade-off between the passband loss and the group delay response of the resulting filter. Chebyshev filters of the first and of the second kind, and also Legendre and Butterworth filters are shown to be special cases of these allpole recursive digital filters. Closed form equations for the computation of the filter coefficients are provided. The design technique is illustrated with examples.

  5. Effect of Materials and Manufacturing on the Bending Stiffness of Vaulting Poles

    Science.gov (United States)

    Davis, C. L.; Kukureka, S. N.

    2012-01-01

    The increase in the world record height achieved in pole vaulting can be related to the improved ability of the athletes, in terms of their fitness and technique, and to the change in materials used to construct the pole. For example in 1960 there was a change in vaulting pole construction from bamboo to glass fibre reinforced polymer (GFRP)…

  6. Finite element modeling of small-scale tapered wood-laminated composite poles with biomimicry features

    Science.gov (United States)

    Cheng Piao; Todd F. Shupe; R.C. Tang; Chung Y. Hse

    2008-01-01

    Tapered composite poles with biomimicry features as in bamboo are a new generation of wood laminated composite poles that may some day be considered as an alternative to solid wood poles that are widely used in the transmission and telecommunication fields. Five finite element models were developed with ANSYS to predict and assess the performance of five types of...

  7. The Neville-Aitken formula for rational interpolants with prescribed poles

    Science.gov (United States)

    Carstensen, C.; Mühlbach, G.

    1992-12-01

    Using a polynomial description of rational interpolation with prescribed poles a simple purely algebraic proof of a Neville-Aitken recurrence formula for rational interpolants with prescribed poles is presented. It is used to compute the general Cauchy-Vandermonde determinant explicitly in terms of the nodes and poles involved.

  8. Mechanical properties of small-scale laminated wood composite poles: effects of taper and webs

    Science.gov (United States)

    Cheng Piao; Todd F. Shupe; R.C. Tang; Chung Y. Hse

    2006-01-01

    Laminated hollow wood composite poles represent an efficient utilization of the timber resource and a promising alternative for solid poles that are commonly used in the power transmission and telecommunication lines. The objective of this study was to improve the performance of composite poles by introducing the bio-mimicry concept into the design of hollow wood...

  9. Oracle ADF Faces cookbook

    CERN Document Server

    Gawish, Amr

    2014-01-01

    This is a cookbook that covers more than 80 different recipes to teach you about different aspects of Oracle ADF Faces. It follows a practical approach and covers how to build your components for reuse in different applications. This book will also help you in tuning the performance of your ADF Faces application. If you are an ADF developer who wants to harness the power of Oracle ADF Faces to create exceptional user interfaces and reactive applications, this book will provide you with the recipes needed to do just that. You will not need to be familiar with Oracle ADF Faces, but you should be

  10. Face inversion increases attractiveness.

    Science.gov (United States)

    Leder, Helmut; Goller, Juergen; Forster, Michael; Schlageter, Lena; Paul, Matthew A

    2017-07-01

    Assessing facial attractiveness is a ubiquitous, inherent, and hard-wired phenomenon in everyday interactions. As such, it has highly adapted to the default way that faces are typically processed: viewing faces in upright orientation. By inverting faces, we can disrupt this default mode, and study how facial attractiveness is assessed. Faces, rotated at 90 (tilting to either side) and 180°, were rated on attractiveness and distinctiveness scales. For both orientations, we found that faces were rated more attractive and less distinctive than upright faces. Importantly, these effects were more pronounced for faces rated low in upright orientation, and smaller for highly attractive faces. In other words, the less attractive a face was, the more it gained in attractiveness by inversion or rotation. Based on these findings, we argue that facial attractiveness assessments might not rely on the presence of attractive facial characteristics, but on the absence of distinctive, unattractive characteristics. These unattractive characteristics are potentially weighed against an individual, attractive prototype in assessing facial attractiveness. Copyright © 2017 The Authors. Published by Elsevier B.V. All rights reserved.

  11. Learning discriminant face descriptor.

    Science.gov (United States)

    Lei, Zhen; Pietikäinen, Matti; Li, Stan Z

    2014-02-01

    Local feature descriptor is an important module for face recognition and those like Gabor and local binary patterns (LBP) have proven effective face descriptors. Traditionally, the form of such local descriptors is predefined in a handcrafted way. In this paper, we propose a method to learn a discriminant face descriptor (DFD) in a data-driven way. The idea is to learn the most discriminant local features that minimize the difference of the features between images of the same person and maximize that between images from different people. In particular, we propose to enhance the discriminative ability of face representation in three aspects. First, the discriminant image filters are learned. Second, the optimal neighborhood sampling strategy is soft determined. Third, the dominant patterns are statistically constructed. Discriminative learning is incorporated to extract effective and robust features. We further apply the proposed method to the heterogeneous (cross-modality) face recognition problem and learn DFD in a coupled way (coupled DFD or C-DFD) to reduce the gap between features of heterogeneous face images to improve the performance of this challenging problem. Extensive experiments on FERET, CAS-PEAL-R1, LFW, and HFB face databases validate the effectiveness of the proposed DFD learning on both homogeneous and heterogeneous face recognition problems. The DFD improves POEM and LQP by about 4.5 percent on LFW database and the C-DFD enhances the heterogeneous face recognition performance of LBP by over 25 percent.

  12. Claw-pole Synchronous Generator for Compressed Air Energy Storage

    Directory of Open Access Journals (Sweden)

    PAVEL Valentina

    2013-05-01

    Full Text Available This paper presents a claw-poles generator for compressed air energy storage systems. It is presented the structure of such a system used for compensating of the intermittency of a small wind energy system. For equipping of this system it is chosen the permanent magnet claw pole synchronous generator obtained by using ring NdFeB permanentmagnets instead of excitation coil. In such a way the complexity of the scheme is reduced and the generator become maintenance free. The new magnetic flux density in the air-gap is calculated by magneticreluctance method and by FEM method and the results are compared with measured values in the old and new generator.

  13. Study of recursive model for pole-zero cancellation circuit

    International Nuclear Information System (INIS)

    Zhou Jianbin; Zhou Wei; Hong Xu; Hu Yunchuan; Wan Xinfeng; Du Xin; Wang Renbo

    2014-01-01

    The output of charge sensitive amplifier (CSA) is a negative exponential signal with long decay time which will result in undershoot after C-R differentiator. Pole-zero cancellation (PZC) circuit is often applied to eliminate undershoot in many radiation detectors. However, it is difficult to use a zero created by PZC circuit to cancel a pole in CSA output signal accurately because of the influences of electronic components inherent error and environmental factors. A novel recursive model for PZC circuit is presented based on Kirchhoff's Current Law (KCL) in this paper. The model is established by numerical differentiation algorithm between the input and the output signal. Some simulation experiments for a negative exponential signal are carried out using Visual Basic for Application (VBA) program and a real x-ray signal is also tested. Simulated results show that the recursive model can reduce the time constant of input signal and eliminate undershoot. (authors)

  14. On the ultimate uncertainty of the top quark pole mass

    Energy Technology Data Exchange (ETDEWEB)

    Beneke, M. [Technische Univ. Muenchen, Garching (Germany). Physik-Department; Marquard, P. [Deutsches Elektronen-Synchrotron (DESY), Zeuthen (Germany); Nason, P. [INFN, Sezione di Milano Bicocca (Italy); Steinhauser, M. [Karlsruher Institut fuer Technologie (Germany). Inst. fuer Theoretische Teilchenphysik

    2016-05-15

    We combine the known asymptotic behaviour of the QCD perturbation series expansion, which relates the pole mass of a heavy quark to the MS mass, with the exact series coefficients up to the four-loop order to determine the ultimate uncertainty of the top-quark pole mass due to the renormalon divergence. We perform extensive tests of our procedure by varying the number of colours and flavours, as well as the scale of the strong coupling and the MS mass, and conclude that this uncertainty is around 70 MeV. We further estimate the additional contribution to the mass relation from the five-loop correction and beyond to be 250 MeV.

  15. Development of a 10-m wedged-pole undulator

    International Nuclear Information System (INIS)

    Robinson, K.E.; Gottschalk, S.C.; James, F.E.; Quimby, D.C.; Slater, J.M.; Valla, A.S.

    1989-01-01

    A 10-m rare earth permanent magnet hybrid undulator called a near infrared scalable undulator system (NISUS) is under construction at Spectra Technology for use in the Boeing FEL program series. The design was optimized for operation at a 1-μm wavelength with the Boeing accelerator parameters. A remotely adjustable compound taper is utilized to achieve optimum startup gain and high saturated extraction. A summary of the relevant design parameters is listed. A major goal was to build NISUS from modules which would allow easy scaling to longer lengths without redesign. Prototype tests for verification of field strength and quality are complete as well as the delivery and installation of the initial 5 m. Improvements relative to the technology used in the earlier tapered hybrid undulator (THUNDER) are highlighted. The wedged-pole configuration is employed for a major increase in field strength while operating the poles farther from saturation

  16. Comminuted inferior pole fracture of patella can be successfully treated with rim-plate-augmented separate vertical wiring.

    Science.gov (United States)

    Cho, Jae-Woo; Kim, Jinil; Cho, Won-Tae; Gujjar, Pranay H; Oh, Chang-Wug; Oh, Jong-Keon

    2018-02-01

    We present the surgical technique of rim-plate-augmented separate vertical wiring for comminuted inferior pole fracture of the patella and report the clinical outcomes. Between July 2013 and January 2016, 13 patients (7 male and 6 female) who were diagnosed with comminuted inferior pole fracture of the patella in preoperative computed tomography and underwent a minimum of 1 year of follow-up were enrolled in this study. Mean patient age was 57.7 years (range 28-72 years). All patients underwent open reduction and internal fixation by rim-plate-augmented separate vertical wiring. Bony union, complications, range of motion and Bostman score were the clinical outcomes. Bony union was achieved in all cases at an average of 10 weeks after surgery (range 8-12). There was no loss of reduction and fixative failure during follow-up. The average range of motion was 127° (range 120°-130°). The mean Bostman score at last follow-up was 29.6 points (range 27-30) and graded excellent in 12 patients. Rim-plate-augmented separate vertical wiring demonstrated secure fixation and favorable clinical outcomes. This study provides evidence for its effectiveness as a fixation method for treating displaced, comminuted inferior pole fracture of the patella.

  17. Hair Loss

    Science.gov (United States)

    ... conditions can cause hair loss, including: Hormonal changes. Hormonal changes and imbalances can cause temporary hair loss. This could be due to pregnancy, childbirth or the onset of menopause. Hormone levels are also affected by the thyroid ...

  18. Hair Loss

    Science.gov (United States)

    ... overall hair thinning and not bald patches. Full-body hair loss. Some conditions and medical treatments, such as ... in the loss of hair all over your body. The hair usually grows back. Patches of scaling that spread ...

  19. Seasonal Evolution of Titan's Stratosphere Near the Poles

    Science.gov (United States)

    Coustenis, A.; Jennings, D. E.; Achterberg, R. K.; Bampasidis, G.; Nixon, C. A.; Lavvas, P.; Cottini, V.; Flasar, F. M.

    2018-02-01

    In this Letter, we report the monitoring of seasonal evolution near Titan’s poles. We find Titan’s south pole to exhibit since 2010 a strong temperature decrease and a dramatic enhancement of several trace species such as complex hydrocarbons and nitriles (HC3N and C6H6 in particular) previously only observed at high northern latitudes. This results from the seasonal change on Titan going from winter (2002) to summer (2017) in the north and, at the same time, the onset of winter in the south pole. During this transition period atmospheric components with longer chemical lifetimes linger in the north, undergoing slow photochemical destruction, while those with shorter lifetimes decrease and reappear in the south. An opposite effect was expected in the north, but not observed with certainty until now. We present here an analysis of high-resolution nadir spectra acquired by Cassini/Cassini Composite Infrared Spectrometer in the past years and describe the temperature and composition variations near Titan’s poles. From 2013 until 2016, the northern polar region has shown a temperature increase of 10 K, while the south has shown a more significant decrease (up to 25 K) in a similar period of time. While the south polar region has been continuously enhanced since about 2012, the chemical content in the north is finally showing a clear depletion for most molecules only since 2015. This is indicative of a non-symmetrical response to the seasons in Titan’s stratosphere that can set constraints on photochemical and GCM models.

  20. REGIONAL DEVELOPMENT THROUGH GROWTH AND URBAN DEVELOPMENT POLES IN ROMANIA

    Directory of Open Access Journals (Sweden)

    Stefana VARVARI

    2015-09-01

    Full Text Available In 2008 the Ministry of Development, Public Works and Housing (now the Ministry of Regional Development and Public Administration prepared the growth poles policy for Romania, establishing seven growth poles to be financed through the Regional Operational Programme 2007-1013, under the Priority Axis no. 1. For 2007-2013 there were also established 11 urban development poles. At present the Ministry is discussing with the European Commission the new Regional Operational Programme 2014-2020 in which the main policy lines regarding integrated territorial development also take into consideration the improvement of the quality of life and the “appearance” of towns and strengthening their role in the region. The main urban agglomerations (county seats are seen as development engines of the regions. The authors analyze the results obtained and the problems that appeared at regional level in what concerns the projects financed under Axis 1 of the ROP 2007-2013 by answering two main questions: did they really had the estimated impact on the growth and urban development poles and on the regions? and was there really an integrated approach used? Based on the results obtained from the analysis of the previous programming period the authors try to recommend some improvements that could be taken into consideration for the development of the Integrated urban development plans and priority projects that are going to be financed by ESI funds under Axis 4 of the new ROP 2014-2020, recommendations that could be taken into consideration when preparing the Guidelines for applicants for this axis.

  1. Tööpuudus 29%, palavikku pole / Rachel Donadio

    Index Scriptorium Estoniae

    Donadio, Rachel

    2010-01-01

    Lõuna-Hispaanias asuvas Cádizis on töötus 29%, ometi pole eurotsooni kõrgeim tööpuuduse määr tekitanud linnas sügavat sotsiaalset rahutust ega massilisi proteste, sest üsna kõrge elukvaliteedi tagavad töötutele kompleksne turvavõrk, mis koosneb varimajandusest, perekonna toetusest ja valitsuse toetusest

  2. Development of a superconducting claw-pole motor

    International Nuclear Information System (INIS)

    Watanabe, E.; Kikukawa, K.; Satoh, Y.; Torii, S.

    2008-01-01

    We have developed and produced a superconducting claw-pole motor for a trial purpose as a method to make the best use of the characteristic of superconductivity without collector rings or rotating superconducting coils that need to be cryocooled, and made some examinations. The unique feature in this motor is to have the mechanism that supports the reaction magnetic force generated in the axial direction

  3. Multiple mechanisms regulate NuMA dynamics at spindle poles.

    Science.gov (United States)

    Kisurina-Evgenieva, Olga; Mack, Gary; Du, Quansheng; Macara, Ian; Khodjakov, Alexey; Compton, Duane A

    2004-12-15

    The large coiled-coil protein NuMA plays an essential role in organizing microtubule minus ends at spindle poles in vertebrate cells. Here, we use both in vivo and in vitro methods to examine NuMA dynamics at mitotic spindle poles. Using fluorescence recovery after photobleaching, we show that an exogenously expressed green-fluorescent-protein/NuMA fusion undergoes continuous exchange between soluble and spindle-associated pools in living cells. These dynamics require cellular energy and display an average half-time for fluorescence recovery of approximately 3 minutes. To explore how NuMA dynamics at spindle poles is regulated, we exploited the association of NuMA with microtubule asters formed in mammalian mitotic extracts. Using a monoclonal antibody specific for human NuMA, we followed the fate of human NuMA associated with microtubule asters upon dilution with a hamster mitotic extract. Consistent with in vivo data, this assay shows that NuMA can be displaced from the core of pre-assembled asters into the soluble pool. The half-time of NuMA displacement from asters under these conditions is approximately 5 minutes. Using this assay, we show that protein kinase activity and the NuMA-binding protein LGN regulate the dynamic exchange of NuMA on microtubule asters. Thus, the dynamic properties of NuMA are regulated by multiple mechanisms including protein phosphorylation and binding to the LGN protein, and the rate of exchange between soluble and microtubule-associated pools suggests that NuMA associates with an insoluble matrix at spindle poles.

  4. Clusters of cyclones encircling Jupiter’s poles

    Science.gov (United States)

    Adriani, A.; Mura, A.; Orton, G.; Hansen, C.; Altieri, F.; Moriconi, M. L.; Rogers, J.; Eichstädt, G.; Momary, T.; Ingersoll, A. P.; Filacchione, G.; Sindoni, G.; Tabataba-Vakili, F.; Dinelli, B. M.; Fabiano, F.; Bolton, S. J.; Connerney, J. E. P.; Atreya, S. K.; Lunine, J. I.; Tosi, F.; Migliorini, A.; Grassi, D.; Piccioni, G.; Noschese, R.; Cicchetti, A.; Plainaki, C.; Olivieri, A.; O’Neill, M. E.; Turrini, D.; Stefani, S.; Sordini, R.; Amoroso, M.

    2018-03-01

    The familiar axisymmetric zones and belts that characterize Jupiter’s weather system at lower latitudes give way to pervasive cyclonic activity at higher latitudes. Two-dimensional turbulence in combination with the Coriolis β-effect (that is, the large meridionally varying Coriolis force on the giant planets of the Solar System) produces alternating zonal flows. The zonal flows weaken with rising latitude so that a transition between equatorial jets and polar turbulence on Jupiter can occur. Simulations with shallow-water models of giant planets support this transition by producing both alternating flows near the equator and circumpolar cyclones near the poles. Jovian polar regions are not visible from Earth owing to Jupiter’s low axial tilt, and were poorly characterized by previous missions because the trajectories of these missions did not venture far from Jupiter’s equatorial plane. Here we report that visible and infrared images obtained from above each pole by the Juno spacecraft during its first five orbits reveal persistent polygonal patterns of large cyclones. In the north, eight circumpolar cyclones are observed about a single polar cyclone; in the south, one polar cyclone is encircled by five circumpolar cyclones. Cyclonic circulation is established via time-lapse imagery obtained over intervals ranging from 20 minutes to 4 hours. Although migration of cyclones towards the pole might be expected as a consequence of the Coriolis β-effect, by which cyclonic vortices naturally drift towards the rotational pole, the configuration of the cyclones is without precedent on other planets (including Saturn’s polar hexagonal features). The manner in which the cyclones persist without merging and the process by which they evolve to their current configuration are unknown.

  5. Coherence between geophysical excitations and celestial pole offsets

    Czech Academy of Sciences Publication Activity Database

    Ron, Cyril; Vondrák, Jan

    2011-01-01

    Roč. 8, č. 3 (2011), s. 243-247 ISSN 1214-9705. [Czech-Polish Workshop on Recent Geodynamics of the Sudeten and Adjacent Areas. Třešť, 04.11.2010-06.11. 2010] R&D Projects: GA ČR GA205/08/0908 Institutional research plan: CEZ:AV0Z10030501 Keywords : geophysical excitations * celestial pole offsets * coherence Subject RIV: BN - Astronomy, Celestial Mechanics, Astrophysics Impact factor: 0.530, year: 2011

  6. Pole particles in Treder's tetrad theory

    Energy Technology Data Exchange (ETDEWEB)

    Fuchs, H.

    1977-01-01

    In the framework of Treder's tetrad theory of gravitation the interaction of pole-particles is considered in post-Newtonian approximation. The perihelion shift for the two-body problems is calculated for different matter-field-couplings. In general it depends not only from the sum of the masses but also from the reduced mass. The additional term is connected with the absorption of gravitation.

  7. Seasonal Evolution of Titan's South Pole 220 cm-1 Cloud

    Science.gov (United States)

    Jennings, Donald

    2016-06-01

    A cloud of ices that had been seen only in Titan's north during winter began to emerge at the south pole in 2012. Discovered by Voyager IRIS as an emission feature at 220 cm-1, the cloud has been studied extensively in both the north and south by Cassini CIRS. The spectral feature acts as a tracer of the seasonal changes at Titan's poles, relating to evolving composition, temperature structure and dynamics. Although candidates have been proposed, the chemical makeup of the cloud has never been identified. The cloud is composed of condensates derived from gases created at high altitude and transported to the cold, shadowed pole. In the north the cloud has diminished gradually over the Cassini mission as Titan has transitioned from winter to spring. The southern cloud, on the other hand, grew rapidly after 2012. By late 2014 it had developed a complex ring structure that was confined to latitudes poleward of 70°S within the deep temperature well that had formed at the south pole [1]. The location of the cloud coincides in latitude with the HCN cloud reported by ISS and VIMS [2,3]. CIRS also saw enhanced gas emissions at those latitudes [4]. When it first formed, the cloud was abundant at altitudes as high as 250 km, while later it was found mostly at 100-150 km, suggesting that the material that had been deposited from above had gathered at the lower altitudes. Radiance from the southern cloud increased until mid-2015 and since then has decreased. The cloud may be transitioning to the more uniform hood morphology familiar in the north. Taking the north and south together, by the end of the Cassini mission in 2017 we will have observed almost an entire seasonal cycle of the ice cloud.

  8. Pole mass, width, and propagators of unstable fermions

    International Nuclear Information System (INIS)

    Kniehl, B.A.; Sirlin, A.

    2008-01-01

    The concepts of pole mass and width are extended to unstable fermions in the general framework of parity-nonconserving gauge theories, such as the Standard Model. In contrast with the conventional on-shell definitions, these concepts are gauge independent and avoid severe unphysical singularities, properties of great importance since most fundamental fermions in nature are unstable particles. General expressions for the unrenormalized and renormalized dressed propagators of unstable fermions and their field-renormalization constants are presented. (orig.)

  9. Performance study of quadrupole with broken line profile pole tip

    International Nuclear Information System (INIS)

    Fan Mingwu; Zhang Tianjue; Chu Chengjie

    1997-01-01

    Most of quadrupole used for beam focusing possess hyperbola profile tip. To simplify machining processes and ensure the assembling accuracy, a broken line profile pole tip is adapted instead of hyperbola. The results of the magnetic field simulation codes and the tests show the good quality field generated by such configuration: not only more uniform field gradient, but also field more concentrated at useful area. These types of quadrupole are used at CYCIAE-30 cyclotron and HI-13 tandem transportation lines

  10. Edgar Savisaar : BRS pole piisavalt investeerinud / Raigo Neudorf

    Index Scriptorium Estoniae

    Neudorf, Raigo

    2006-01-01

    Majandus- ja kommunikatsiooniminister on rahul, et riigi ja BRS-iga saavutati kokkulepe ettevõtte aktsiate tagasiostuks, kuid leiab, et BRS pole täitnud võetud investeerimiskohustusi ning seega peab järgnevatel aastatel suunama ettevõtte kaasajastamisse miljardeid kroone. Vt. samas: Jüri Käo: investeeringute kogumaht ületas nõutu; Savisaar: Jüri Käo ajab pada; Pingelised läbirääkimised BRS-iga

  11. Background Studies for Acoustic Neutrino Detection at the South Pole

    Science.gov (United States)

    Abbasi, R.; Abdou, Y.; Abu-Zayyad, T.; Adams, J.; Aguilar, J. A.; Ahlers, M.; Andeen, K.; Auffenberg, J.; Bai, X.; Baker, M.; hide

    2012-01-01

    The detection of acoustic signals from ultra-high energy neutrino interactions is a promising method. to measure the flux of cosmogenic neutrinos expected on Earth. The energy threshold for this process depends strongly on the absolute noise level in the target material. The South Pole Acoustic Test Setup (SPATS). deployed in the upper part of four boreholes of the IceCube Neutrino Observatory, has monitored the noise in Antarctic ice at the geographic South Pole for more than two years down to 500 m depth. The noise is very stable and Gaussian distributed, Lacking an in situ calibration up to now, laboratory measurements have been used to estimate the absolute noise level in the 10-50 kHz frequency range to be smaller than 20 mPa. Using a threshold trigger. sensors of the South Pole Acoustic Test Setup registered acoustic events in the IceCube detector volume and its vicinity. Acoustic signals from refreezing IceCube holes and from anthropogenic sources have been used to test the localization of acoustic events. An upper limit on the neutrino flux at energies E(sub v) > 10(exp 11) GeV is derived from acoustic data taken over eight months.

  12. THE SUSTAINABLE DEVELOPMENT OF THE BRASOV GROWTH POLE

    Directory of Open Access Journals (Sweden)

    Aida CATANA

    2016-12-01

    Full Text Available The demographic dynamics analysed in the context of the relationship between economic development and social inclusion presents an image of the sustainable development of a community as well as the manner how the financial resources have been used. With an allocation of 74.3 million euro in the programming period 2007-2013, the Brasov Growth Pole has pursued the contribution to the achievement of sustainable development since 2005 by the participation in the Agenda 21. The implementation of projects with European financing in areas such as transport, social and educational infrastructure or tourism have generated changes/demographic movements, which this paper proposes to present. The evolution of the stable population, its dynamics at the level of each locality that is part of the Brasov growth pole as well as the dynamics of the number of employees or the development of the unemployment rate are presented by the cluster analysis. The effects of the European financing obtained from Regional Operational Programme 2007-2013 are thus reflected in the sustainable development of the Brasov growth pole from the point of view of the dynamics of the population

  13. Factorization and resummation for collinear poles in QCD amplitudes

    Energy Technology Data Exchange (ETDEWEB)

    Dixon, Lance J.; Magnea, Lorenzo; Sterman, George

    2008-05-28

    We study the origin of subleading soft and collinear poles of form factors and amplitudes in dimensionally-regulated massless gauge theories. In the case of form factors of fundamental fields, these poles originate from a single function of the coupling, denoted G({alpha}{sub s}), depending on both the spin and gauge quantum numbers of the field. We relate G({alpha}{sub s}) to gauge-theory matrix elements involving the gluon field strength. We then show that G({alpha}{sub s}) is the sum of three terms: a universal eikonal anomalous dimension, a universal non-eikonal contribution, given by the coefficient B{sub {delta}}({alpha}{sub s}) of {delta}(1-z) in the collinear evolution kernel, and a process-dependent short-distance coefficient function, which does not contribute to infrared poles. Using general results on the factorization of soft and collinear singularities in fixed-angle massless gauge theory amplitudes, we conclude that all such singularities are captured by the eikonal approximation, supplemented only by the knowledge of B{sub {delta}}({alpha}{sub s}). We explore the consequences of our results for conformal gauge theories, where in particular we find a simple exact relation between the form factor and the cusp anomalous dimension.

  14. Automatic Pole and Q-Value Extraction for RF Structures

    Energy Technology Data Exchange (ETDEWEB)

    C. Potratz, H.-W. Glock, U. van Rienen, F. Marhauser

    2011-09-01

    The experimental characterization of RF structures like accelerating cavities often demands for measuring resonant frequencies of Eigenmodes and corresponding (loaded) Q-values over a wide spectral range. A common procedure to determine the Q-values is the -3dB method, which works well for isolated poles, but may not be applicable directly in case of multiple poles residing in close proximity (e.g. for adjacent transverse modes differing by polarization). Although alternative methods may be used in such cases, this often comes at the expense of inherent systematic errors. We have developed an automation algorithm, which not only speeds up the measurement time significantly, but is also able to extract Eigenfrequencies and Q-values both for well isolated and overlapping poles. At the same time the measurement accuracy may be improved as a major benefit. To utilize this procedure merely complex scattering parameters have to be recorded for the spectral range of interest. In this paper we present the proposed algorithm applied to experimental data recorded for superconducting higher-order-mode damped multi-cell cavities as an application of high importance.

  15. Management of lower pole nephrolithiasis: a critical analysis.

    Science.gov (United States)

    Lingeman, J E; Siegel, Y I; Steele, B; Nyhuis, A W; Woods, J R

    1994-03-01

    The results of extracorporeal shock wave lithotripsy (ESWL*) and percutaneous nephrostolithotomy for the treatment of lower pole nephrolithiasis were examined in 32 consecutive patients undergoing percutaneous nephrostolithotomy at the Methodist Hospital of Indiana and through meta-analysis of publications providing adequate stratification of treatment results. Of 101 cases managed with percutaneous nephrostolithotomy 91 (90%) were stone-free, a result significantly better than that achieved with ESWL (1,733 of 2,927 stone-free, 59%). Stone-free rates with percutaneous nephrostolithotomy were independent of stone burden, whereas stone-free rates with ESWL were inversely correlated to the stone burden treated. The morbidity of patients undergoing percutaneous nephrostolithotomy at our hospital was minimal, with a mean hospital stay of 4.7 +/- 2.8 days. No blood transfusions were required. All patients became stone-free. The percentage of urolithiasis patients with lower pole calculi is increasing. Because of the significantly greater efficacy of percutaneous nephrostolithotomy for lower pole calculi, particularly stones larger than 10 mm. in diameter, further consideration should be given to an initial approach with percutaneous nephrostolithotomy.

  16. Morphing morphing faces

    NARCIS (Netherlands)

    Lier, R.J. van

    2009-01-01

    We have made cyclic morphing animations using two different faces. The morphing animations gradually evolved from one face to the other, and vice versa. When free viewing, the perceived changes were not very large, but the changes could easily be observed. Observers were asked to fixate on a dot

  17. Spatial patterns of pollution associated with creosote treated poles in Mälardalen

    OpenAIRE

    Forselius, Ellen

    2015-01-01

    Creosote is a product name given to a mixture of several hundred compounds, which is often used to protect wooden poles from rot and insect damage, however it has also been linked to causing cancer in humans. Alternative materials for power poles include concrete, steel, composite and non-treated wooden poles. This report looks at Mälarenergi Elnät ABs 17,000 creosote coated poles and their patterns of pollution. GIS analyses in ArcGIS were used to evaluate which creosote poles are most criti...

  18. Chiasmata promote monopolar attachment of sister chromatids and their co-segregation toward the proper pole during meiosis I.

    Directory of Open Access Journals (Sweden)

    Yukinobu Hirose

    2011-03-01

    Full Text Available The chiasma is a structure that forms between a pair of homologous chromosomes by crossover recombination and physically links the homologous chromosomes during meiosis. Chiasmata are essential for the attachment of the homologous chromosomes to opposite spindle poles (bipolar attachment and their subsequent segregation to the opposite poles during meiosis I. However, the overall function of chiasmata during meiosis is not fully understood. Here, we show that chiasmata also play a crucial role in the attachment of sister chromatids to the same spindle pole and in their co-segregation during meiosis I in fission yeast. Analysis of cells lacking chiasmata and the cohesin protector Sgo1 showed that loss of chiasmata causes frequent bipolar attachment of sister chromatids during anaphase. Furthermore, high time-resolution analysis of centromere dynamics in various types of chiasmate and achiasmate cells, including those lacking the DNA replication checkpoint factor Mrc1 or the meiotic centromere protein Moa1, showed the following three outcomes: (i during the pre-anaphase stage, the bipolar attachment of sister chromatids occurs irrespective of chiasma formation; (ii the chiasma contributes to the elimination of the pre-anaphase bipolar attachment; and (iii when the bipolar attachment remains during anaphase, the chiasmata generate a bias toward the proper pole during poleward chromosome pulling that results in appropriate chromosome segregation. Based on these results, we propose that chiasmata play a pivotal role in the selection of proper attachments and provide a backup mechanism that promotes correct chromosome segregation when improper attachments remain during anaphase I.

  19. A QUESTÃO DA MOBILIDADE URBANA NAS METRÓPOLES BRASILEIRAS

    Directory of Open Access Journals (Sweden)

    Valéria Pero

    2015-12-01

    Full Text Available RESUMO O tempo de deslocamento de casa ao trabalho tem se elevado substancialmente nas regiões metropolitanas brasileiras durante a última década. Esse fenômeno tem implicações fortes sobre o bem-estar dos indivíduos, porém as consequências desse problema não se distribuem uniformemente entre a população. O presente trabalho visa contribuir para o debate sobre a questão da mobilidade urbana nas metrópoles brasileiras analisando a evolução do tempo de deslocamento entre 1992 e 2013 e suas diferenças de acordo com características do trabalhador, como sexo, cor e renda per capita , e do posto de trabalho. Verifica-se que o aumento do tempo médio de deslocamento ocorreu a partir de 2003, caracterizando uma questão particularmente importante para as metrópoles brasileiras no terceiro milênio. Os trabalhadores com maiores tempos médios de deslocamento residem nas regiões metropolitanas do Rio de Janeiro e de São Paulo. Entretanto, as maiores taxas de crescimento ocorreram nas metrópoles do Pará, Salvador e Recife, sugerindo a necessidade de melhor direcionamento e planejamento de políticas públicas na mobilidade urbana. Considerando as diferenças socioeconômicas, destaca-se que os mais pobres e os mais ricos (extremos da distribuição de renda tendem a apresentar tempos de deslocamento menores do que os trabalhadores de famílias de renda média. Esse padrão se mantém ao longo do tempo, com aumento do tempo médio de deslocamento entre os mais pobres, mostrando uma face da desigualdade. Porém, o maior aumento ocorreu entre os mais ricos, colocando a questão da mobilidade urbana para além dos problemas de exclusão social.

  20. POLE-LIKE OBJECT EXTRACTION FROM MOBILE LIDAR DATA

    Directory of Open Access Journals (Sweden)

    H. Zheng

    2016-06-01

    Full Text Available Object detection and recognition from LiDAR (Light Detection And Ranging data has been a research topic in the fields of photogrammetry and computer vision. Unlike point clouds collected in well-controlled indoor environments, point clouds in urban environments are more complex due to complexity of the real world. For example, trees sometimes close to signs or buildings, which will cause occlusions in the point clouds. Current object detection or reconstruction algorithms will have problems when recognizing objects with severe occlusions caused by trees etc. In this paper, a robust vegetation removal method and a DBSCAN based pole-like object detection method are proposed. Based on observation that major difference between vegetation and other rigid objects is their penetrability with respect to LiDAR, we introduce a local roughness measure to differentiate rigid objects from non-rigid ones (vegetation in this paper. First, a local sphere with a small radius is generated for each input point. Three principal components of the local sphere are then calculated, and a plane is determined. The roughness is obtained through calculating the standard deviation of distances from all inside points to the plane by a weighted summation of the normalized distances. The further the point to the plane, the smaller the weight is. Finally, a graph cuts based method is introduced to classify the input point sets into two groups. The data term is defined by the normalized roughness of the current point, and the smoothness term is defined by the normalized distance between the point and its nearest neighbour point. In terms of pole-like object detection, first, a uniformed 2D grid is generated through projecting all the points to the XY-plane. The seed points of the pole-like objects are obtained by determining the x and y coordinates by the centres of the highest density cells of the grid and the z coordinate by the mean height of the point sets of each object

  1. Live imaging of spindle pole disorganization in docetaxel-treated multicolor cells

    International Nuclear Information System (INIS)

    Sakaushi, Shinji; Nishida, Kumi; Minamikawa, Harumi; Fukada, Takashi; Oka, Shigenori; Sugimoto, Kenji

    2007-01-01

    Treatment of cells with docetaxel at low concentrations induces aberrant bipolar spindles of which two centrosomes stay at only one pole, and also induces multipolar spindles. To gain insight into the relations between centrosome impairment and structural defects of the spindle, live-cell imaging was performed on a human MDA Auro/imp/H3 cell line in which centrosomes/mitotic spindles, nuclear membrane and chromatin were simultaneously visualized by fluorescent proteins. In the presence of docetaxel at IC 50 concentration, the centrosomes did not segregate, and multiple aster-like structures ectopically arose around the disappearing nuclear membrane. Those ectopic structures formed an acentrosomal pole opposing to the two-centrosomes-containing pole. In late metaphase, one pole often fragmented into multiple spindle poles, leading multipolar division. These results suggest that spindle pole fragility may be induced by centrosome impairment, and collapse of the pole may contribute to induction of aneuploid daughter cells

  2. Telehealth is Face-to-Face Service Delivery

    OpenAIRE

    CASON, JANA

    2017-01-01

    The Commentary contests the increasingly outdated and narrow use of the terminology ?face-to-face? (often abbreviated as F2F) to connote clinical interactions in which both the client and the practitioner are physically present in the same room or space. An expanded definition is necessary because when delivered synchronously via videoconferencing, telehealth also provides face-to-face services (i.e., the practitioner and the client view each other?s faces). Terminology that uses face-to-face...

  3. Face-Lift

    Science.gov (United States)

    ... several weeks. Keeping your head elevated and applying cold compresses can help. Plan to have your surgery at least 6 weeks before any important social events. Changes in skin sensation. During a face-lift, the repositioning of your ...

  4. Face the Facts

    Science.gov (United States)

    ... content Skip Navigation Department of Health and Human Services Your Browser does not support javascript, so the search function on this page is disabled 1-800-677-1116 Home > Resources > Factsheets > Face ...

  5. Face Detection and Recognition

    National Research Council Canada - National Science Library

    Jain, Anil K

    2004-01-01

    This report describes research efforts towards developing algorithms for a robust face recognition system to overcome many of the limitations found in existing two-dimensional facial recognition systems...

  6. Laparoscopic upper pole heminephroureterectomy in children: Seven-year experience

    Directory of Open Access Journals (Sweden)

    Antonio Marte

    2015-01-01

    Full Text Available Background: Minimally invasive surgery is the current approach to perform heminephroureterectomy (HN in children. This can be obtained through a transperitoneal (TP or a retroperitoneal approach. Here, we report our experience using a TP approach. Materials and Methods: From 2005 to 2014, 22 TP laparoscopic upper poles HN were performed at our institution. There were nine girls and 13 boys aged between 20 months and 6 years (mean age 3.9. Eight patients were diagnosed prenatally, 17 patients presented with urinary tract infection (UTI and three with vomiting and failure to thrive. The indication for HN was reflux nephropathy and UTI in non-functioning upper pole in 19 patients and cystic dysplasia in 1 patient. The surgical technique involved the following steps: Cystoscopic recognition; positioning of 3-4 trocar (right HN; identification of the kidney (detachment of the colon; isolation and low ligation of the dilated ureter; decrossing from renal vessels; section of the parenchyma by LigaSure; haemostasis with clips and LigaSure; drain. Results: The mean operative time was 154 min (range: 81-220 min. All patients were discharged from the 2 nd to 4 th day. Neither major complication nor conversion was recorded. 1 patient presented leakage of urine for 7 days from the drainage which resolved spontaneously. At ultrasound follow-up, 5 patients showed a secondary perirenal cyst, 2-5 cm diameter that resolved spontaneously. Conclusion: The results indicate that laparoscopic upper pole heminephrectomy is the treatment of choice in cases of non-functioning dilated lower segments of duplicated kidneys. The use of laparoscopic approach offers a good working space, a good visual control of the vessels and allows a very low isolation of the ureteral stump which counterbalance the peritoneal violation.

  7. DETECTION AND CLASSIFICATION OF POLE-LIKE OBJECTS FROM MOBILE MAPPING DATA

    Directory of Open Access Journals (Sweden)

    K. Fukano

    2015-08-01

    Full Text Available Laser scanners on a vehicle-based mobile mapping system can capture 3D point-clouds of roads and roadside objects. Since roadside objects have to be maintained periodically, their 3D models are useful for planning maintenance tasks. In our previous work, we proposed a method for detecting cylindrical poles and planar plates in a point-cloud. However, it is often required to further classify pole-like objects into utility poles, streetlights, traffic signals and signs, which are managed by different organizations. In addition, our previous method may fail to extract low pole-like objects, which are often observed in urban residential areas. In this paper, we propose new methods for extracting and classifying pole-like objects. In our method, we robustly extract a wide variety of poles by converting point-clouds into wireframe models and calculating cross-sections between wireframe models and horizontal cutting planes. For classifying pole-like objects, we subdivide a pole-like object into five subsets by extracting poles and planes, and calculate feature values of each subset. Then we apply a supervised machine learning method using feature variables of subsets. In our experiments, our method could achieve excellent results for detection and classification of pole-like objects.

  8. Pole-zero form fractional model identification in frequency domain

    International Nuclear Information System (INIS)

    Mansouri, R.; Djamah, T.; Djennoune, S.; Bettayeb, M.

    2009-01-01

    This paper deals with system identification in the frequency domain using non integer order models given in the pole-zero form. The usual identification techniques cannot be used in this case because of the non integer orders of differentiation which makes the problem strongly nonlinear. A general identification method based on Levenberg-Marquardt algorithm is developed and allows to estimate the (2n+2m+1) parameters of the model. Its application to identify the ''skin effect'' of a squirrel cage induction machine modeling is then presented.

  9. Fiber coupler end face wavefront surface metrology

    Science.gov (United States)

    Compertore, David C.; Ignatovich, Filipp V.; Marcus, Michael A.

    2015-09-01

    Despite significant technological advances in the field of fiber optic communications, one area remains surprisingly `low-tech': fiber termination. In many instances it involves manual labor and subjective visual inspection. At the same time, high quality fiber connections are one of the most critical parameters in constructing an efficient communication link. The shape and finish of the fiber end faces determines the efficiency of a connection comprised of coupled fiber end faces. The importance of fiber end face quality becomes even more critical for fiber connection arrays and for in the field applications. In this article we propose and demonstrate a quantitative inspection method for the fiber connectors using reflected wavefront technology. The manufactured and polished fiber tip is illuminated by a collimated light from a microscope objective. The reflected light is collected by the objective and is directed to a Shack-Hartmann wavefront sensor. A set of lenses is used to create the image of the fiber tip on the surface of the sensor. The wavefront is analyzed by the sensor, and the measured parameters are used to obtain surface properties of the fiber tip, and estimate connection loss. For example, defocus components in the reflected light indicate the presence of bow in the fiber end face. This inspection method provides a contact-free approach for quantitative inspection of fiber end faces and for estimating the connection loss, and can potentially be integrated into a feedback system for automated inspection and polishing of fiber tips and fiber tip arrays.

  10. Loss of detectability and indeterminate results: Challenges facing ...

    African Journals Online (AJOL)

    In addition, infants already initiated on combination ART (cART) may be retested with PCR assays for 'confirmatory' purposes, including assessment prior to adoption. The potential for cART to compromise the sensitivity of HIV-1 PCR assays has been described, although there are limited and conflicting data regarding the ...

  11. DISCOVERY OF FOG AT THE SOUTH POLE OF TITAN

    International Nuclear Information System (INIS)

    Brown, M. E.; Smith, A. L.; Chen, C.; Adamkovics, M.

    2009-01-01

    While Saturn's moon Titan appears to support an active methane hydrological cycle, no direct evidence for surface-atmosphere exchange has yet appeared. The indirect evidence, while compelling, could be misleading. It is possible, for example, that the identified lake features could be filled with ethane, an involatile long-term residue of atmospheric photolysis; the apparent stream and channel features could be ancient remnants of a previous climate; and the tropospheric methane clouds, while frequent, could cause no rain to reach the surface. We report here the detection of fog at the south pole of Titan during late summer using observations from the VIMS instrument on board the Cassini spacecraft. While terrestrial fog can form from a variety of causes, most of these processes are inoperable on Titan. Fog on Titan can only be caused by evaporation of nearly pure liquid methane; the detection of fog provides the first direct link between surface and atmospheric methane. Based on the detections presented here, liquid methane appears widespread at the south pole of Titan in late southern summer, and the hydrological cycle on Titan is currently active.

  12. Acoustic wave filter based on periodically poled lithium niobate.

    Science.gov (United States)

    Courjon, Emilie; Bassignot, Florent; Ulliac, Gwenn; Benchabane, Sarah; Ballandras, Sylvain

    2012-09-01

    Solutions for the development of compact RF passive transducers as an alternative to standard surface or bulk acoustic wave devices are receiving increasing interest. This article presents results on the development of an acoustic band-pass filter based on periodically poled ferroelectric domains in lithium niobate. The fabrication of periodically poled transducers (PPTs) operating in the range of 20 to 650 MHz has been achieved on 3-in (76.2-mm) 500-μm-thick wafers. This kind of transducer is able to excite elliptical as well as longitudinal modes, yielding phase velocities of about 3800 and 6500 ms(-1), respectively. A new type of acoustic band-pass filter is proposed, based on the use of PPTs instead of the SAWs excited by classical interdigital transducers. The design and the fabrication of such a filter are presented, as well as experimental measurements of its electrical response and transfer function. The feasibility of such a PPT-based filter is thereby demonstrated and the limitations of this method are discussed.

  13. Groebner Basis Solutions to Satellite Trajectory Control by Pole Placement

    Science.gov (United States)

    Kukelova, Z.; Krsek, P.; Smutny, V.; Pajdla, T.

    2013-09-01

    Satellites play an important role, e.g., in telecommunication, navigation and weather monitoring. Controlling their trajectories is an important problem. In [1], an approach to the pole placement for the synthesis of a linear controller has been presented. It leads to solving five polynomial equations in nine unknown elements of the state space matrices of a compensator. This is an underconstrained system and therefore four of the unknown elements need to be considered as free parameters and set to some prior values to obtain a system of five equations in five unknowns. In [1], this system was solved for one chosen set of free parameters with the help of Dixon resultants. In this work, we study and present Groebner basis solutions to this problem of computation of a dynamic compensator for the satellite for different combinations of input free parameters. We show that the Groebner basis method for solving systems of polynomial equations leads to very simple solutions for all combinations of free parameters. These solutions require to perform only the Gauss-Jordan elimination of a small matrix and computation of roots of a single variable polynomial. The maximum degree of this polynomial is not greater than six in general but for most combinations of the input free parameters its degree is even lower. [1] B. Palancz. Application of Dixon resultant to satellite trajectory control by pole placement. Journal of Symbolic Computation, Volume 50, March 2013, Pages 79-99, Elsevier.

  14. Towards a research pole in photonics in Western Romania

    Science.gov (United States)

    Duma, Virgil-Florin; Negrutiu, Meda L.; Sinescu, Cosmin; Rominu, Mihai; Miutescu, Eftimie; Burlea, Amelia; Vlascici, Miomir; Gheorghiu, Nicolae; Cira, Octavian; Hutiu, Gheorghe; Mnerie, Corina; Demian, Dorin; Marcauteanu, Corina; Topala, Florin; Rolland, Jannick P.; Voiculescu, Ioana; Podoleanu, Adrian G.

    2014-07-01

    We present our efforts in establishing a Research Pole in Photonics in the future Arad-Timisoara metropolitan area projected to unite two major cities of Western Romania. Research objectives and related training activities of various institutions and groups that are involved are presented in their evolution during the last decade. The multi-disciplinary consortium consists principally of two universities, UAVA (Aurel Vlaicu University of Arad) and UMF (Victor Babes Medicine and Pharmacy University of Timisoara), but also of the Arad County Emergency University Hospital and several innovative SMEs, such as Bioclinica S.A. (the largest array of medical analysis labs in the region) and Inteliform S.R.L. (a competitive SME focused on mechatronics and mechanical engineering). A brief survey of the individual and joint projects of these institutions is presented, together with their teaching activities at graduate and undergraduate level. The research Pole collaborates in R&D, training and education in biomedical imaging with universities in USA and Europe. Collaborative activities, mainly on Optical Coherence Tomography (OCT) projects are presented in a multidisciplinary approach that includes optomechatronics, precision mechanics and optics, dentistry, medicine, and biology.

  15. Semantic representations in the temporal pole predict false memories.

    Science.gov (United States)

    Chadwick, Martin J; Anjum, Raeesa S; Kumaran, Dharshan; Schacter, Daniel L; Spiers, Hugo J; Hassabis, Demis

    2016-09-06

    Recent advances in neuroscience have given us unprecedented insight into the neural mechanisms of false memory, showing that artificial memories can be inserted into the memory cells of the hippocampus in a way that is indistinguishable from true memories. However, this alone is not enough to explain how false memories can arise naturally in the course of our daily lives. Cognitive psychology has demonstrated that many instances of false memory, both in the laboratory and the real world, can be attributed to semantic interference. Whereas previous studies have found that a diverse set of regions show some involvement in semantic false memory, none have revealed the nature of the semantic representations underpinning the phenomenon. Here we use fMRI with representational similarity analysis to search for a neural code consistent with semantic false memory. We find clear evidence that false memories emerge from a similarity-based neural code in the temporal pole, a region that has been called the "semantic hub" of the brain. We further show that each individual has a partially unique semantic code within the temporal pole, and this unique code can predict idiosyncratic patterns of memory errors. Finally, we show that the same neural code can also predict variation in true-memory performance, consistent with an adaptive perspective on false memory. Taken together, our findings reveal the underlying structure of neural representations of semantic knowledge, and how this semantic structure can both enhance and distort our memories.

  16. Vertical vector face lift.

    Science.gov (United States)

    Somoano, Brian; Chan, Joanna; Morganroth, Greg

    2011-01-01

    Facial rejuvenation using local anesthesia has evolved in the past decade as a safer option for patients seeking fewer complications and minimal downtime. Mini- and short-scar face lifts using more conservative incision lengths and extent of undermining can be effective in the younger patient with lower face laxity and minimal loose, elastotic neck skin. By incorporating both an anterior and posterior approach and using an incision length between the mini and more traditional face lift, the Vertical Vector Face Lift can achieve longer-lasting and natural results with lesser cost and risk. Submentoplasty and liposuction of the neck and jawline, fundamental components of the vertical vector face lift, act synergistically with superficial musculoaponeurotic system plication to reestablish a more youthful, sculpted cervicomental angle, even in patients with prominent jowls. Dramatic results can be achieved in the right patient by combining with other procedures such as injectable fillers, chin implants, laser resurfacing, or upper and lower blepharoplasties. © 2011 Wiley Periodicals, Inc.

  17. The effect of poling conditions on the performance of piezoelectric energy harvesters fabricated by wet chemistry

    KAUST Repository

    Fuentes-Fernandez, Erika Maria-Anai

    2015-03-25

    The effect of poling conditions on the power output of piezoelectric energy harvesters using sol-gel based Pb(Zr0.53,Ti0.47)O3-Pb(Zn1/3,Nb2/3)O3 piezoelectric thin-films has been investigated. A strong correlation was established between the poling efficiency and harvester output. A method based on simple capacitance-voltage measurements is shown to be an effective approach to estimate the power output of harvesters poled under different conditions. The poling process was found to be thermally activated with an activation energy of 0.12 eV, and the optimum poling conditions were identified (200 kV cm-1, 250 °C for 50 min). The voltage output and power density obtained under optimum poling conditions were measured to be 558 V cm-2 and 325 μW cm-2, respectively. © The Royal Society of Chemistry.2015.

  18. Field analysis and enhancement of multi-pole magnetic components fabricated on printed circuit board

    International Nuclear Information System (INIS)

    Chiu, K.-C.; Chen, C.-S.

    2007-01-01

    A multi-pole magnetic component magnetized with a fine magnetic pole pitch of less than 1 mm is very difficult to achieve by using traditional methods. Moreover, it requires a precise mechanical process and a complicated magnetization system. Different fine magnetic pole pitches of 300, 350 and 400 μm have been accomplished on 9-pole magnetic components through the printed circuit board (PCB) manufacturing technology. Additionally, another fine magnetic pole pitch of 500 μm was also fabricated on a dual-layered (DL) wire circuit structure to investigate the field enhancement. After measurements, a gain factor of 1.37 was obtained in the field strength. The field variations among different magnetic pole pitches were analyzed in this paper

  19. Loss of chance: what loss?

    Science.gov (United States)

    Bird, Sara

    2006-05-01

    A recent New South Wales judgment, Rufo v Hosking, explored the concept of 'loss of a chance' in medical negligence claims. 'Loss of a chance' claims involve an allegation that the patient lost the chance of a better outcome as a result of the negligence of the medical practitioner. This article outlines the case and discusses the implications of the judgment for medical practitioners.

  20. How Well Do Computer-Generated Faces Tap Face Expertise?

    Directory of Open Access Journals (Sweden)

    Kate Crookes

    Full Text Available The use of computer-generated (CG stimuli in face processing research is proliferating due to the ease with which faces can be generated, standardised and manipulated. However there has been surprisingly little research into whether CG faces are processed in the same way as photographs of real faces. The present study assessed how well CG faces tap face identity expertise by investigating whether two indicators of face expertise are reduced for CG faces when compared to face photographs. These indicators were accuracy for identification of own-race faces and the other-race effect (ORE-the well-established finding that own-race faces are recognised more accurately than other-race faces. In Experiment 1 Caucasian and Asian participants completed a recognition memory task for own- and other-race real and CG faces. Overall accuracy for own-race faces was dramatically reduced for CG compared to real faces and the ORE was significantly and substantially attenuated for CG faces. Experiment 2 investigated perceptual discrimination for own- and other-race real and CG faces with Caucasian and Asian participants. Here again, accuracy for own-race faces was significantly reduced for CG compared to real faces. However the ORE was not affected by format. Together these results signal that CG faces of the type tested here do not fully tap face expertise. Technological advancement may, in the future, produce CG faces that are equivalent to real photographs. Until then caution is advised when interpreting results obtained using CG faces.

  1. Iron Pole Shape Optimization of IPM Motors Using an Integrated Method

    Directory of Open Access Journals (Sweden)

    JABBARI, A.

    2010-02-01

    Full Text Available An iron pole shape optimization method to reduce cogging torque in Interior Permanent Magnet (IPM motors is developed by using the reduced basis technique coupled by finite element and design of experiments methods. Objective function is defined as the minimum cogging torque. The experimental design of Taguchi method is used to build the approximation model and to perform optimization. This method is demonstrated on the rotor pole shape optimization of a 4-poles/24-slots IPM motor.

  2. Lower Pole Calyceal Stone and Lithotripsy are Issues with Clearance Fact or Reality?

    Directory of Open Access Journals (Sweden)

    M. Hammad Ather

    2013-12-01

    Full Text Available The lower pole calyceal (LPC stone continues to be an enigma. The complex anatomy of the lower pole collecting system, along with other factors like acute pelvi calyceal angle and narrow and long infundibulum, are some of the complicating factors affecting stone clearance. There have been many studies assessing the impact of collecting system anatomy and most conclude that the complex anatomy of the lower pole collecting system does impact the overall stone-free rate.

  3. A temporary face support

    Energy Technology Data Exchange (ETDEWEB)

    Popov, V.I.; Bakhtin, V.N.; Tolkachev, N.I.

    1980-03-30

    A temporary face support is proposed. It includes a beam supported by hydraulic jacks on the housing of the cutter-loader with a working tool and rotary pressure regulator. It differs in that to decrease the volume of unsecured roofing in the face space between the leading edge of the beam and the cutting tool of the cutter-loader, the beam is hinged onto the housing of the rotary pressure regulator by a fastened connecting rod, and the hydraulic jacks are provided with additional powered elements with a mechanism that regulates the length of the cut-off plate of the hydraulic pump when the seam pressure changes.

  4. Hair Loss

    Science.gov (United States)

    ... and Nutrition Healthy Food Choices Weight Loss and Diet Plans Nutrients and Nutritional Info Sugar and Sugar Substitutes Exercise and Fitness Exercise Basics Sports Safety Injury Rehabilitation Emotional Well-Being Mental Health ...

  5. Memory loss

    Science.gov (United States)

    A person with memory loss needs a lot of support. It helps to show the person familiar objects, music, or and photos or play familiar music. Write down when the person should take any medicine or do other ...

  6. Hair Loss

    Science.gov (United States)

    ... hair bulb. This is where the hair's color pigment, or melanin, is produced. Most people lose about ... diabetes or thyroid disease , can interfere with hair production and cause hair loss. People with lupus can ...

  7. Shadow poles in coupled-channel problems calculated with the Berggren basis

    Science.gov (United States)

    Id Betan, R. M.; Kruppa, A. T.; Vertse, T.

    2018-02-01

    Background: In coupled-channels models the poles of the scattering S matrix are located on different Riemann sheets. Physical observables are affected mainly by poles closest to the physical region but sometimes shadow poles have considerable effect too. Purpose: The purpose of this paper is to show that in coupled-channels problems all poles of the S matrix can be located by an expansion in terms of a properly constructed complex-energy basis. Method: The Berggren basis is used for expanding the coupled-channels solutions. Results: The locations of the poles of the S matrix for the Cox potential, constructed for coupled-channels problems, were numerically calculated and compared with the exact ones. In a nuclear physics application the Jπ=3 /2+ resonant poles of 5He were calculated in a phenomenological two-channel model. The properties of both the normal and shadow resonances agree with previous findings. Conclusions: We have shown that, with an appropriately chosen Berggren basis, all poles of the S matrix including the shadow poles can be determined. We have found that the shadow pole of 5He migrates between Riemann sheets if the coupling strength is varied.

  8. Time domain oscillating poles: Stability redefined in Memristor based Wien-oscillators

    KAUST Repository

    Talukdar, Abdul Hafiz Ibne

    2012-07-28

    Traditionally, the necessary and sufficient condition for any system to be oscillating is that its poles are located on the imaginary (jω) axis. In this paper, for the first time, we have shown that systems can oscillate with time-domain oscillating poles. The idea is verified using a Memristor based Wien oscillator. Sustained oscillations are observed without having the poles of the system fixed on the imaginary axis and the oscillating behavior of the system poles is reported. The oscillating resistance and triangular shape of FFT are also demonstrated with mathematical reasoning and simulation results to support the unusual and surprising characteristics. © 2009 IEEE.

  9. Hidden loss

    DEFF Research Database (Denmark)

    Kieffer-Kristensen, Rikke; Johansen, Karen Lise Gaardsvig

    2013-01-01

    finding indicates that the children experienced numerous losses, many of which were often suppressed or neglected by the children to protect the ill parents. CONCLUSIONS: The findings indicated that the children seemed to make a special effort to hide their feelings of loss and grief in order to protect...... the ill parent. These findings contribute to a deeper understanding of the traumatic process of parental ABI that some children experience and emphasize the importance of family-centred interventions that include the children....

  10. Person perception involves functional integration between the extrastriate body area and temporal pole.

    Science.gov (United States)

    Greven, Inez M; Ramsey, Richard

    2017-02-01

    The majority of human neuroscience research has focussed on understanding functional organisation within segregated patches of cortex. The ventral visual stream has been associated with the detection of physical features such as faces and body parts, whereas the theory-of-mind network has been associated with making inferences about mental states and underlying character, such as whether someone is friendly, selfish, or generous. To date, however, it is largely unknown how such distinct processing components integrate neural signals. Using functional magnetic resonance imaging and connectivity analyses, we investigated the contribution of functional integration to social perception. During scanning, participants observed bodies that had previously been associated with trait-based or neutral information. Additionally, we independently localised the body perception and theory-of-mind networks. We demonstrate that when observing someone who cues the recall of stored social knowledge compared to non-social knowledge, a node in the ventral visual stream (extrastriate body area) shows greater coupling with part of the theory-of-mind network (temporal pole). These results show that functional connections provide an interface between perceptual and inferential processing components, thus providing neurobiological evidence that supports the view that understanding the visual environment involves interplay between conceptual knowledge and perceptual processing. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

  11. PrimeFaces blueprints

    CERN Document Server

    Jonna, Sudheer

    2014-01-01

    If you are a Java developer with experience of frontend UI development, and want to take the plunge to develop stunning UI applications with the most popular JSF framework, PrimeFaces, then this book is for you. For those with entrepreneurial aspirations, this book will provide valuable insights into how to utilize successful business models.

  12. Face the voice

    DEFF Research Database (Denmark)

    Lønstrup, Ansa

    2014-01-01

    Belle, Neumark). Finally, the article will discuss the specific artistic combination and our auditory experience of mediated human voices and sculpturally projected faces in an art museum context under the general conditions of the societal panophonia of disembodied and mediated voices, as promoted by Steven...

  13. Problems facing developing countries

    International Nuclear Information System (INIS)

    Anon.

    1986-01-01

    Financing, above all political and technical considerations, remains the major obstacle faced by developing countries who wish to embark on a nuclear power programme. According to the IAEA, the support of the official lending agencies of the suppliers is essential. (author)

  14. Two Faces of Japan.

    Science.gov (United States)

    Beasley, Conger, Jr.

    1992-01-01

    Discusses the inconsistency between Japanese exploitation of world natural resources and gestures to provide leadership in ecologically innovative technology. Explores Japanese culture, power structure, population trends, environmental ethics, industrialism, and international business practices as they relate to the philosophical face of…

  15. The transparent face mask.

    Science.gov (United States)

    Rivers, E A; Strate, R G; Solem, L D

    1979-02-01

    Fabrication of an accurate transparent mask for total contact pressure to the healed burned face proved helpful in controlling scarring. Wearing the mask for 20 hours daily, secured by elastic straps giving 35-mmHG pressure to the scar, can prevent the original facial contours from being distorted by contracting scar tissue.

  16. Robust Statistical Face Frontalization

    NARCIS (Netherlands)

    Sagonas, Christos; Panagakis, Yannis; Zafeiriou, Stefanos; Pantic, Maja

    2015-01-01

    Recently, it has been shown that excellent results can be achieved in both facial landmark localization and pose-invariant face recognition. These breakthroughs are attributed to the efforts of the community to manually annotate facial images in many different poses and to collect 3D facial data. In

  17. Neural synchronization during face-to-face communication.

    Science.gov (United States)

    Jiang, Jing; Dai, Bohan; Peng, Danling; Zhu, Chaozhe; Liu, Li; Lu, Chunming

    2012-11-07

    Although the human brain may have evolutionarily adapted to face-to-face communication, other modes of communication, e.g., telephone and e-mail, increasingly dominate our modern daily life. This study examined the neural difference between face-to-face communication and other types of communication by simultaneously measuring two brains using a hyperscanning approach. The results showed a significant increase in the neural synchronization in the left inferior frontal cortex during a face-to-face dialog between partners but none during a back-to-back dialog, a face-to-face monologue, or a back-to-back monologue. Moreover, the neural synchronization between partners during the face-to-face dialog resulted primarily from the direct interactions between the partners, including multimodal sensory information integration and turn-taking behavior. The communicating behavior during the face-to-face dialog could be predicted accurately based on the neural synchronization level. These results suggest that face-to-face communication, particularly dialog, has special neural features that other types of communication do not have and that the neural synchronization between partners may underlie successful face-to-face communication.

  18. Voicing on Virtual and Face to Face Discussion

    Science.gov (United States)

    Yamat, Hamidah

    2013-01-01

    This paper presents and discusses findings of a study conducted on pre-service teachers' experiences in virtual and face to face discussions. Technology has brought learning nowadays beyond the classroom context or time zone. The learning context and process no longer rely solely on face to face communications in the presence of a teacher.…

  19. METRÓPOLE E SUA LÓGICA CAPITALISTA ATUAL FACE AO REGIME DE ACUMULAÇÃO PATRIMONIAL

    Directory of Open Access Journals (Sweden)

    Sandra Lencioni

    2015-01-01

    Full Text Available En la actualidad, la metrópolis se desarrolla bajo el dominio del capital financiero, que, en relación estrecha con el sector inmobiliario se tornan hegemónicos bajo las demás formas de capital. Ese es el gran cambio que caracteriza el momento de desarrollo capitalista que Aglietta (1988 denominó, régimen de acumulación patrimonial. En este régimen de acumulación, el proceso de valorización del capital se hace acompañar, significativamente, del proceso de capitalización. Según este proceso, el capital financiero aumenta, aunque de una manera ficticia de valorización, ya que se realiza por fuera del proceso de producción, por ello es llamado de capitalización. Bajo el imperio de las rentas (financiera e inmobiliaria la metrópolis se desar - rolla, se deconstruye, se construye y se reconstruye sobre si misma, expandiéndose de forma difusa, por un extenso territorio.

  20. Faceness-Net: Face Detection through Deep Facial Part Responses.

    Science.gov (United States)

    Yang, Shuo; Luo, Ping; Loy, Chen Change; Tang, Xiaoou

    2017-08-11

    We propose a deep convolutional neural network (CNN) for face detection leveraging on facial attributes based supervision. We observe a phenomenon that part detectors emerge within CNN trained to classify attributes from uncropped face images, without any explicit part supervision. The observation motivates a new method for finding faces through scoring facial parts responses by their spatial structure and arrangement. The scoring mechanism is data-driven, and carefully formulated considering challenging cases where faces are only partially visible. This consideration allows our network to detect faces under severe occlusion and unconstrained pose variations. Our method achieves promising performance on popular benchmarks including FDDB, PASCAL Faces, AFW, and WIDER FACE.

  1. Real Time Face Quality Assessment for Face Log Generation

    DEFF Research Database (Denmark)

    Kamal, Nasrollahi; Moeslund, Thomas B.

    2009-01-01

    Summarizing a long surveillance video to just a few best quality face images of each subject, a face-log, is of great importance in surveillance systems. Face quality assessment is the back-bone for face log generation and improving the quality assessment makes the face logs more reliable....... Developing a real time face quality assessment system using the most important facial features and employing it for face logs generation are the concerns of this paper. Extensive tests using four databases are carried out to validate the usability of the system....

  2. Flashed face distortion effect: grotesque faces from relative spaces.

    Science.gov (United States)

    Tangen, Jason M; Murphy, Sean C; Thompson, Matthew B

    2011-01-01

    We describe a novel face distortion effect resulting from the fast-paced presentation of eye-aligned faces. When cycling through the faces on a computer screen, each face seems to become a caricature of itself and some faces appear highly deformed, even grotesque. The degree of distortion is greatest for faces that deviate from the others in the set on a particular dimension (eg if a person has a large forehead, it looks particularly large). This new method of image presentation, based on alignment and speed, could provide a useful tool for investigating contrastive distortion effects and face adaptation.

  3. Human faces are slower than chimpanzee faces.

    Directory of Open Access Journals (Sweden)

    Anne M Burrows

    Full Text Available While humans (like other primates communicate with facial expressions, the evolution of speech added a new function to the facial muscles (facial expression muscles. The evolution of speech required the development of a coordinated action between visual (movement of the lips and auditory signals in a rhythmic fashion to produce "visemes" (visual movements of the lips that correspond to specific sounds. Visemes depend upon facial muscles to regulate shape of the lips, which themselves act as speech articulators. This movement necessitates a more controlled, sustained muscle contraction than that produced during spontaneous facial expressions which occur rapidly and last only a short period of time. Recently, it was found that human tongue musculature contains a higher proportion of slow-twitch myosin fibers than in rhesus macaques, which is related to the slower, more controlled movements of the human tongue in the production of speech. Are there similar unique, evolutionary physiologic biases found in human facial musculature related to the evolution of speech?Using myosin immunohistochemistry, we tested the hypothesis that human facial musculature has a higher percentage of slow-twitch myosin fibers relative to chimpanzees (Pan troglodytes and rhesus macaques (Macaca mulatta. We sampled the orbicularis oris and zygomaticus major muscles from three cadavers of each species and compared proportions of fiber-types. Results confirmed our hypothesis: humans had the highest proportion of slow-twitch myosin fibers while chimpanzees had the highest proportion of fast-twitch fibers.These findings demonstrate that the human face is slower than that of rhesus macaques and our closest living relative, the chimpanzee. They also support the assertion that human facial musculature and speech co-evolved. Further, these results suggest a unique set of evolutionary selective pressures on human facial musculature to slow down while the function of this muscle

  4. Face-to-Face Activities in Blended Learning

    DEFF Research Database (Denmark)

    Kjærgaard, Annemette

    While blended learning combines online and face-to-face teaching, research on blended learning has primarily focused on the role of technology and the opportunities it creates for engaging students. Less focus has been put on face-to-face activities in blended learning. This paper argues...... that it is not only the online activities in blended learning that provide new opportunities for rethinking pedagogy in higher education, it is also imperative to reconsider the face-to-face activities when part of the learning is provided online. Based on a review of blended learning in business and management...... education, we identify what forms of teaching and learning are suggested to take place face-to-face when other activities are moved online. We draw from the Community of Inquiry framework to analyze how face-to-face activities contribute to a blended learning pedagogy and discuss the implications...

  5. Face recognition system and method using face pattern words and face pattern bytes

    Science.gov (United States)

    Zheng, Yufeng

    2014-12-23

    The present invention provides a novel system and method for identifying individuals and for face recognition utilizing facial features for face identification. The system and method of the invention comprise creating facial features or face patterns called face pattern words and face pattern bytes for face identification. The invention also provides for pattern recognitions for identification other than face recognition. The invention further provides a means for identifying individuals based on visible and/or thermal images of those individuals by utilizing computer software implemented by instructions on a computer or computer system and a computer readable medium containing instructions on a computer system for face recognition and identification.

  6. Roadside tree/pole crash barrier field test

    Science.gov (United States)

    Wilson, A. H.

    1979-01-01

    A series of tests was carried out to evaluate the performance of a crash barrier designed to protect the occupants of an automobile from serious injury. The JPL barrier design is a configuration of empty aluminum beverage cans contained in a tear-resistant bag which, in turn, is encased in a collapsible container made of plywood and steel. Tests were conducted with a driven vehicle impacting the barrier. The basic requirements of NCHRP Report 153 were followed except that speeds of 30 mph rather than 60 mph were used. Accelerometer readings on the driver's helmet showed that the driver was never subjected to dangerous decelerations, and never experienced more than temporary discomfort. Also, all of the requirements of the cited report were met. An extrapolation of data indicated that the JPL barrier installed in front of a tree or telephone pole along a roadside would also have met the requirements at a speed of 40 mph.

  7. An adaptive single pole autoreclosure based on zero sequence power

    Energy Technology Data Exchange (ETDEWEB)

    Elkalashy, Nagy I.; Darwish, Hatem A.; Taalab, Abdel-Maksoud I.; Izzularab, Mohmmad A. [Electrical Engineering Department, Faculty of Engineering, Menoufiya University, Shebin Elkom 32511 (Egypt)

    2007-04-15

    In this paper, a novel adaptive single pole autoreclosure is introduced. This reclosure is based on monitoring the fundamental component of the zero sequence instantaneous power to detect the extinction instant of the arc in its secondary period. Thus, adaptive closing instant can be achieved. The concept of reclosure is validated via typical examples of transmission line exposed to ground arcing fault. Effects of fault location and load flow on the accuracy of the technique are examined. Discriminatory zones of the secondary arc period in the zero sequence power domains are determined. A proposed threshold for the reclosing instant is introduced and examined. Validation of the proposed algorithm is verified via Digital Signal Processing (DSP) experimental test set-up. The test results corroborate the efficacy of proposed technique. (author)

  8. Performance of claw-poled PM-stepping motor

    International Nuclear Information System (INIS)

    Liu, C.P.; Jeng, G.R.; Chen, W.C.; Tsai, M.C.; Wu, K.T.; Yao, Y.D.

    2007-01-01

    Present work is to analyze the performance of a permanent-magnetic (PM) stepping motor with claw poles by using the magnetic-circuit simulation technique. In this paper, we calculate the torque characteristics of the motor, such as the detent and the holding torques, and the step-position error by changing the gap between the upper and the lower stators and the staggered angle between the two stators. Through comparison of numerical data with experiment measurements, we found that the detent torque could be effectively reduced by increasing the stator-to-stator gap and further by decreasing the step-position error. Furthermore, the holding torque could be unchanged as the stator assemblage changed; however, it would be degenerated under the condition of low magnetization

  9. Lunar South Pole space water extraction and trucking system

    International Nuclear Information System (INIS)

    Zuppero, A.; Zupp, G.; Schnitzler, B.; Larson, T.K.; Rice, J.W.

    1998-03-01

    This concept proposes to use thermal processes alone to extract water from the lunar South Pole and launch payloads to low lunar orbit. Thermal steam rockets would use water propellant for space transportation. The estimated mass of a space water tanker powered by a nuclear heated steam rocket suggests it can be designed for launch in the Space Shuttle bay. The performance depends on the feasibility of a nuclear reactor rocket engine producing steam at 1,100 degrees Kelvin, with a power density of 150 Megawatts per ton of rocket, and operating for thousands of 20 minute cycles. An example uses reject heat from a small nuclear electric power supply to melt 17,800 tons per year of lunar ice. A nuclear heated steam rocket would use the propellant water to launch and deliver 3,800 tons of water per year to a 100 km low lunar orbit

  10. Bacterial diversity in snow on North Pole ice floes

    DEFF Research Database (Denmark)

    Hauptmann, Aviaja Zenia Edna Lyberth; Stibal, Marek; Bælum, Jacob

    2014-01-01

    sites clustered together when compared to the underlying environments of sea ice and ocean water. The Shannon indices ranged from 2.226 to 3.758, and the Chao1 indices showed species richness between 293 and 353 for the three samples. The relatively low abundances and diversity found in the samples......The microbial abundance and diversity in snow on ice floes at three sites near the North Pole was assessed using quantitative PCR and 454 pyrosequencing. Abundance of 16S rRNA genes in the samples ranged between 43 and 248 gene copies per millilitre of melted snow. A total of 291,331 sequences were...... indicate a lower rate of microbial input to this snow habitat compared to snow in the proximity of terrestrial and anthropogenic sources of microorganisms. The differences in species composition and diversity between the sites show that apparently similar snow habitats contain a large variation...

  11. Ruthenium therapy of choroidal melanomas of the posterior pole

    International Nuclear Information System (INIS)

    Langmann, G.; Faschinger, C.; Langmann, A.; Poier, E.

    1992-01-01

    The indications for conservative treatment of intraocular melanomas of the posterior pole with radioactive plaques are controversial. Melanomas located at the macula or adjacent to the fovea are regarded as relative contraindications for conservative treatment. Three melanomas of the macula have been treated at our department meanwhile. The tumor elevation ranged between 3.5 and 6 mm, the distance to the fovea between 0.5 and 2 dd. An average radiation dosage between 130 and 160 Gy was delivered to the apex of the tumors. The duration of observation was between 12 months to 4 years. The tumor regression was satisfactory in all 3 cases, additional photocoagulation was necessary in one case of incomplete tumor regression. Pretreatment visual acuity ranged between 0.8 and 0.1, posttreatment visual acuity between 0.8 and 0.25. In one case we observed a local radiation vasculopathy. General examination did not reveal any signs of metastases. (authors)

  12. Effect of materials and manufacturing on the bending stiffness of vaulting poles

    Science.gov (United States)

    Davis, C. L.; Kukureka, S. N.

    2012-09-01

    The increase in the world record height achieved in pole vaulting can be related to the improved ability of the athletes, in terms of their fitness and technique, and to the change in materials used to construct the pole. For example in 1960 there was a change in vaulting pole construction from bamboo to glass fibre reinforced polymer (GFRP) composites. The lighter GFRP pole enabled the athletes to have a faster run-up, resulting in a greater take-off speed, giving them more kinetic energy to convert into potential energy and hence height. GFRP poles also have a much higher failure stress than bamboo, so the poles were engineered to bend under the load of the athlete, thereby storing elastic strain energy that can be released as the pole straightens, resulting in greater energy efficiency. The bending also allowed athletes to change their vaulting technique from a style that involved the body remaining almost upright during the vault to one where the athlete goes over the bar with their feet upwards. Modern vaulting poles can be made from GFRP and/or carbon fibre reinforced polymer (CFRP) composites. The addition of carbon fibres maintains the mechanical properties of the pole, but allows a reduction in the weight. The number and arrangement of the fibres determines the mechanical properties, in particular the bending stiffness. Vaulting poles are also designed for an individual athlete to take into account each athlete’s ability and physical characteristics. The poles are rated by ‘weight’ to allow athletes to select an appropriate pole for their ability. This paper will review the development of vaulting poles and the requirements to maximize performance. The properties (bending stiffness and pre-bend) and microstructure (fibre volume fraction and lay-up) of typical vaulting poles will be discussed. Originally published as Davis C L and Kukureka S N (2004) Effect of materials and manufacturing on the bending stiffness of vaulting poles The Engineering of

  13. Analysis of magnetic abrasive finishing with slotted magnetic pole

    Science.gov (United States)

    Jayswal, S. C.; Jain, V. K.; Dixit, P. M.

    2004-06-01

    Magnetic Abrasive Finishing (MAF) is relatively a new finishing process among the advanced finishing processes in which the workpiece is kept in the magnetic field created by two poles of an electromagnet. The working gap between the workpiece and the magnet is filled with magnetic abrasive particles. A flexible magnetic abrasive brush is formed, acting as a multipoint cutting tool, due to the effect of magnetic field in the working gap. This process is capable of producing the surface finish of nanometer range. Most of the researchers have been using the electromagnet having a slot in it to improve the performance of the process but hardly any information is available about its effect on the process performance. This paper deals with the effect of a slot made in the electromagnet on the forces and surface quality during MAF. An experimental set-up is designed and fabricated for the measurement of the magnetic field distribution in the working gap. The magnetic field is simulated using a finite element model of the process. The magnetic field is also measured experimentally to validate the theoretical results. It indicates a good agreement between the experimental results and simulated values. The finite element method is further used for the evaluation of the magnetic force and surface quality during MAF. To our surprise it is found that the force under the slot is negative, even then process performance is improved. MAF process removes a very small amount of material by indentation and rotation of the magnetic abrasive particles in the circular tracks. Due to rotation of the magnetic abrasive flexible brush, grooves are formed on the workpiece surface which decides the surface profile after MAF. Surface quality is determined on the basis of the surface profile achieved by equating the volume of groove produced. These results show an improvement in finishing rate while using a slotted pole surface.

  14. Determination of regional Euler pole parameters for Eastern Austria

    Science.gov (United States)

    Umnig, Elke; Weber, Robert; Schartner, Matthias; Brueckl, Ewald

    2017-04-01

    The horizontal motion of lithospheric plates can be described as rotations around a rotation axes through the Earth's center. The two possible points where this axes intersects the surface of the Earth are called Euler poles. The rotation is expressed by the Euler parameters in terms of angular velocities together with the latitude and longitude of the Euler pole. Euler parameters were calculated from GPS data for a study area in Eastern Austria. The observation network is located along the Mur-Mürz Valley and the Vienna Basin. This zone is part of the Vienna Transfer Fault, which is the major fault system between the Eastern Alps and the Carpathians. The project ALPAACT (seismological and geodetic monitoring of ALpine-PAnnonian ACtive Tectonics) investigated intra plate tectonic movements within the Austrian part in order to estimate the seismic hazard. Precise site coordinate time series established from processing 5 years of GPS observations are available for the regional network spanning the years from 2010.0 to 2015.0. Station velocities with respect to the global reference frame ITRF2008 have been computed for 23 sites. The common Euler vector was estimated on base of a subset of reliable site velocities, for stations directly located within the area of interest. In a further step a geokinematic interpretation shall be carried out. Therefore site motions with respect to the Eurasian Plate are requested. To obtain this motion field different variants are conceivable. In a simple approach the mean ITRF2008 velocity of IGS site GRAZ can be adopted as Eurasian rotational velocity. An improved alternative is to calculate site-specific velocity differences between the Euler rotation and the individual site velocities. In this poster presentation the Euler parameters, the residual motion field as well as first geokinematic interpretation results are presented.

  15. The Caledonian face test: A new test of face discrimination.

    Science.gov (United States)

    Logan, Andrew J; Wilkinson, Frances; Wilson, Hugh R; Gordon, Gael E; Loffler, Gunter

    2016-02-01

    This study aimed to develop a clinical test of face perception which is applicable to a wide range of patients and can capture normal variability. The Caledonian face test utilises synthetic faces which combine simplicity with sufficient realism to permit individual identification. Face discrimination thresholds (i.e. minimum difference between faces required for accurate discrimination) were determined in an "odd-one-out" task. The difference between faces was controlled by an adaptive QUEST procedure. A broad range of face discrimination sensitivity was determined from a group (N=52) of young adults (mean 5.75%; SD 1.18; range 3.33-8.84%). The test is fast (3-4 min), repeatable (test-re-test r(2)=0.795) and demonstrates a significant inversion effect. The potential to identify impairments of face discrimination was evaluated by testing LM who reported a lifelong difficulty with face perception. While LM's impairment for two established face tests was close to the criterion for significance (Z-scores of -2.20 and -2.27) for the Caledonian face test, her Z-score was -7.26, implying a more than threefold higher sensitivity. The new face test provides a quantifiable and repeatable assessment of face discrimination ability. The enhanced sensitivity suggests that the Caledonian face test may be capable of detecting more subtle impairments of face perception than available tests. Copyright © 2015 Elsevier Ltd. All rights reserved.

  16. Development of a field pole of 1 MW-class HTS motor

    International Nuclear Information System (INIS)

    Yuan, S; Kimura, Y; Miki, M; Felder, B; Tsuzuki, K; Izumi, M; Ida, T; Umemoto, K; Aizawa, K; Yokoyama, M

    2010-01-01

    We report a field-pole high-temperature superconductor (HTS) magnet designed for 1 MW-class motor for propulsion. The field pole is assembled to the rotor of the radial-type motor. Each field pole is composed of HTS-Bi2223 tape wound into coils which have been piled up as a double pancake coils. In the design concept of the motor, we employ field poles without iron core. We prepared the test field-pole coil, whose dimension is smaller than the designed one for 1 MW, and tested its performances after cooling under self-field and external magnetic field. We verified the operation with the minimum bend radius of the coils required in the motor design, while keeping an optimal current which is lower than the critical current of the field-pole coil. The test HTS field poles were successfully cooled down and operated under a magnetic field ranging up to 5 T. We report the results of the test field-pole coil and the manufacture of a practical racetrack coil with Bi2223 and discuss the adaptability to 1 MW-class motors.

  17. Experience on impregnation of wood.en poles with water borne salts

    African Journals Online (AJOL)

    part of pole treated. To ensure this diffusion of the preservative all around, the pole is pricked every. 8 - 10 cm. vertically and 4 - 5 cm peripherally. The treatment with COBRA was discontinued soon after for the following reasons:- I. Leechability. Since the process depends on osmosis, the preservative must be highly soluble ...

  18. The practice of pole dance as a leisure activity in Denmark

    DEFF Research Database (Denmark)

    Jensen, Andorra Lynn

    2015-01-01

    The aim of this study is to explore the how pole dance is practiced as a form of leisure activity in Denmark. The methodical approach is qualitative and inspired by ethnography. I have conducted a field study where I have observed and participated in the pole dance culture in Copenhagen from May...

  19. Converting point-wise nuclear cross sections to pole representation using regularized vector fitting

    Science.gov (United States)

    Peng, Xingjie; Ducru, Pablo; Liu, Shichang; Forget, Benoit; Liang, Jingang; Smith, Kord

    2018-03-01

    Direct Doppler broadening of nuclear cross sections in Monte Carlo codes has been widely sought for coupled reactor simulations. One recent approach proposed analytical broadening using a pole representation of the commonly used resonance models and the introduction of a local windowing scheme to improve performance (Hwang, 1987; Forget et al., 2014; Josey et al., 2015, 2016). This pole representation has been achieved in the past by converting resonance parameters in the evaluation nuclear data library into poles and residues. However, cross sections of some isotopes are only provided as point-wise data in ENDF/B-VII.1 library. To convert these isotopes to pole representation, a recent approach has been proposed using the relaxed vector fitting (RVF) algorithm (Gustavsen and Semlyen, 1999; Gustavsen, 2006; Liu et al., 2018). This approach however needs to specify ahead of time the number of poles. This article addresses this issue by adding a poles and residues filtering step to the RVF procedure. This regularized VF (ReV-Fit) algorithm is shown to efficiently converge the poles close to the physical ones, eliminating most of the superfluous poles, and thus enabling the conversion of point-wise nuclear cross sections.

  20. A Visit to the South Pole-Adventures of the First Indian to Winter ...

    Indian Academy of Sciences (India)

    Home; Journals; Resonance – Journal of Science Education; Volume 15; Issue 4. A Visit to the South Pole - Adventures of the First Indian to Winter-Over the South Pole and Explore Antarctica. Parmjit Singh Sehra. Reflections Volume 15 Issue 4 April 2010 pp 384-391 ...

  1. High-resolution second-harmonic microscopy of poled silica waveguides

    DEFF Research Database (Denmark)

    Beermann, Jonas; Bozhevolnyi, Sergey I.; Pedersen, Kjeld

    2003-01-01

    A second-harmonic scanning optical microscopy (SHSOM) apparatus operating in reflection is used for high-resolution imaging of second-order optical non-linearities (SONs) in electric-field poled silica-based waveguides. SHSOM of domain walls in a periodically poled KTiOPO4 crystal is performed...

  2. Electron self-energy calculation using a general multi-pole approximation

    CERN Document Server

    Soininen, J A; Shirley, E L

    2003-01-01

    We present a method for calculating the inverse of the dielectric matrix in a solid using a band Lanczos algorithm. The method produces a multi-pole approximation for the inverse dielectric matrix with an arbitrary number of poles. We discuss how this approximation can be used to calculate the screened Coulomb interaction needed for electron self-energy calculations in solids.

  3. Threshold for strong thermal dephasing in periodically poled KTP in external cavity frequency doubling

    DEFF Research Database (Denmark)

    Lundeman, Jesper Holm; Jensen, Ole Bjarlin; Andersen, Peter E.

    2009-01-01

    We present a measurement series of the efficiency of periodically poled KTP used for second-harmonic generation in an external phase-locked cavity. Due to the high absorption (0.01 cm^−1) in the PPKTP crystal at the pump wavelength a strong thermal dephasing of the periodically poled grating...

  4. High-resolution second-harmonic microscopy of poled silica waveguides

    DEFF Research Database (Denmark)

    Beermann, Jonas; Bozhevolnyi, Sergey I.; Pedersen, Kjeld

    2003-01-01

    A second-harmonic scanning optical microscopy (SHSOM) apparatus operating in reflection is used for high-resolution imaging of second-order optical non-linearities (SONs) in electric-field poled silica-based waveguides. SHSOM of domain walls in a periodically poled KTiOPO_4 crystal is performed...

  5. Development of a field pole of 1 MW-class HTS motor

    Science.gov (United States)

    Yuan, S.; Kimura, Y.; Miki, M.; Felder, B.; Tsuzuki, K.; Ida, T.; Izumi, M.; Umemoto, K.; Aizawa, K.; Yokoyama, M.

    2010-06-01

    We report a field-pole high-temperature superconductor (HTS) magnet designed for 1 MW-class motor for propulsion. The field pole is assembled to the rotor of the radial-type motor. Each field pole is composed of HTS-Bi2223 tape wound into coils which have been piled up as a double pancake coils. In the design concept of the motor, we employ field poles without iron core. We prepared the test field-pole coil, whose dimension is smaller than the designed one for 1 MW, and tested its performances after cooling under self-field and external magnetic field. We verified the operation with the minimum bend radius of the coils required in the motor design, while keeping an optimal current which is lower than the critical current of the field-pole coil. The test HTS field poles were successfully cooled down and operated under a magnetic field ranging up to 5 T. We report the results of the test field-pole coil and the manufacture of a practical racetrack coil with Bi2223 and discuss the adaptability to 1 MW-class motors.

  6. Stellar population samples at the galactic poles. IV. Luminosity function for the M-type dwarfs at the South Pole

    International Nuclear Information System (INIS)

    Eggen, O.J.

    1976-01-01

    The (UBVRI) photometry of all M dwarfs which are within 10degree of the South Galactic Pole and brighter than visual magnitude 15, and which have annual proper motions greater than 0/sup prime/./sub /096, are discussed. The observations themselves are listed and discussed in a recent Astrophysical Journal Supplement. The luminosity function is found to be very similar, in the overlapping sections, to that previously derived spectrophotometrically from the M stars near the Sun, and the extension to M/subV/ near +13 mag indicates that this luminosity is near the peak of that function. No support is found in these data for the recently suggested superabundance of low velocity M stars near the Sun

  7. Foil Face Seal Testing

    Science.gov (United States)

    Munson, John

    2009-01-01

    In the seal literature you can find many attempts by various researchers to adapt film riding seals to the gas turbine engine. None have been successful, potential distortion of the sealing faces is the primary reason. There is a film riding device that does accommodate distortion and is in service in aircraft applications, namely the foil bearing. More specifically a foil thrust bearing. These are not intended to be seals, and they do not accommodate large axial movement between shaft & static structure. By combining the 2 a unique type of face seal has been created. It functions like a normal face seal. The foil thrust bearing replaces the normal primary sealing surface. The compliance of the foil bearing allows the foils to track distortion of the mating seal ring. The foil seal has several perceived advantages over existing hydrodynamic designs, enumerated in the chart. Materials and design methodology needed for this application already exist. Also the load capacity requirements for the foil bearing are low since it only needs to support itself and overcome friction forces at the antirotation keys.

  8. Telehealth is Face-to-Face Service Delivery.

    Science.gov (United States)

    Cason, Jana

    2017-01-01

    The Commentary contests the increasingly outdated and narrow use of the terminology 'face-to-face' (often abbreviated as F2F) to connote clinical interactions in which both the client and the practitioner are physically present in the same room or space. An expanded definition is necessary because when delivered synchronously via videoconferencing, telehealth also provides face-to-face services (i.e., the practitioner and the client view each other's faces). Terminology that uses face-to-face to connote only in-person care is limiting and perpetuates language that is out of line with progressive US regulatory language and broad interpretation within existing regulatory language. It is this author's hope that this commentary will raise awareness of the important policy implications associated with this seemingly minor distinction in terminology and impact the lingering misapplication of the term, face-to-face.

  9. Hearing Loss

    Science.gov (United States)

    ... law Sound level, decibels Duration, daily BASED ON OCCUPATIONAL SAFETY & HEALTH ADMINISTRATION, 2008 90 8 hours 92 6 hours 95 4 hours 97 3 hours 100 2 hours 102 1.5 hours 105 1 hour 110 30 minutes 115 15 minutes or less Complications Hearing loss can have a significant effect on your quality ...

  10. Experiencing Loss

    DEFF Research Database (Denmark)

    Kristiansen, Maria; Younis, Tarek; Hassani, Amani

    2015-01-01

    In this article, we explore how Islam, minority status and refugee experiencesintersect in shaping meaning-making processes following bereavement. We do this througha phenomenological analysis of a biographical account of personal loss told by Aisha, a Muslim Palestinian refugee living in Denmark...

  11. Glass fiber -reinforced plastic tapered poles for transmission and distribution lines: development and experimental study

    International Nuclear Information System (INIS)

    Ibrahim, S.; Burachysnsky, V.; Polyzois, D.

    1999-01-01

    A research project to develop lightweight poles for use in power transmission and distribution lines and involving the use of glass fiber-reinforced plastic using the filament winding process is described. Twelve full scale specimen poles were designed, fabricated and subjected to cantilever bending to test failure modes. The test parameters included fiber orientation, ratio of longitudinal-to-circumferential fiber, and the number of layers. Results showed that local buckling was the most dominant failure mode, attributable to the high radius-to-thickness ratio of the specimen poles. Overall, however, these fiber-reinforced plastic poles compared favourably to wooden poles in carrying capacity with significant weight reduction. Lateral displacement at ultimate loads did not exceed the acceptable limit of 10 per cent of the specimen free length. 7 refs., 3 tabs., 2 figs

  12. FEM Analysis of Brushless DC Servomotor with Fractional Number of Slots per Pole

    Directory of Open Access Journals (Sweden)

    BALUTA, G.

    2014-02-01

    Full Text Available The authors present in this paper the analysis with Finite Element Method (FEM of the magnetic circuit for a Brushless DC servomotor with fractional number of slots/pole (9 slots and 10 poles. For this purpose, FEMM 4.2 software package was used for the analysis. To obtain the waveforms of Back-ElectroMotive Forces (BEMFs, electromagnetic and cogging torque for servomotor a program in LUA scripting language (integrated into interactive shell of FEMM4.2 has been created. A comparation with a structure with integer number of slots/pole (18 slots and 6 poles was also realized. The analysis results prove that the structure chosen is an optimal solution: sinusoidal waveforms of BEMFs, improved electromagnetic torque and reduced cogging torque. Therefore, the operating characteristics of the servomotor with 9/10 slots/poles manufactured by Sistem Euroteh Company and included in an integrated electrical drives system are presented in this paper.

  13. Institutional Evaluation in Poles of the Open University System of Brazil

    Directory of Open Access Journals (Sweden)

    Alexciano de Sousa Martins

    2018-03-01

    Full Text Available The study wanted to know the institutional evaluation in poles of distance education, of the Open University of Brazil (UAB system, analyzing the poles of the State of Ceará. The UAB system of the Brazilian Ministry of Education makes it possible to offer courses of higher level agreements with public universities. Ceará counts on UAB poles, since 2006, that form teachers and other professionals, even in regions lacking public higher education. The objective of this study was to discuss the importance of the institutional evaluation in the poles of the Open University of Brazil program through an exploratory and descriptive field research, showing that the institutional evaluation at the poles is minimal and out of line with the legislation in force. Suggestions on how to develop the evaluative practice.

  14. Non-uniformly sampled grids in double pole coordinate system for freeform reflector construction

    Science.gov (United States)

    Ma, Donglin; Pacheco, Shaun; Feng, Zexin; Liang, Rongguang

    2015-08-01

    We propose a new method to design freeform reflectors by nonuniformly sampling the source intensity distribution in double pole coordinate system. In double pole coordinate system, there is no pole for the whole hemisphere because both poles of the spherical coordinate system are moved to southernmost point of the sphere and overlapped together. With symmetric definition of both angular coordinates in the modified double pole coordinate system, a better match between the source intensity distribution and target irradiance distribution can be achieved for reflectors with large acceptance solid angle, leading to higher light efficiency and better uniformity on the target surface. With non-uniform sampling of the source intensity, we can design circular freeform reflector to obtain uniform rectangular illumination pattern. Aided by the feedback optimization, the freeform reflector can achieve the collection efficiency for ideal point source over 0.7 and relative standard deviation (RSD) less than 0.1.

  15. Face processing pattern under top-down perception: a functional MRI study

    Science.gov (United States)

    Li, Jun; Liang, Jimin; Tian, Jie; Liu, Jiangang; Zhao, Jizheng; Zhang, Hui; Shi, Guangming

    2009-02-01

    Although top-down perceptual process plays an important role in face processing, its neural substrate is still puzzling because the top-down stream is extracted difficultly from the activation pattern associated with contamination caused by bottom-up face perception input. In the present study, a novel paradigm of instructing participants to detect faces from pure noise images is employed, which could efficiently eliminate the interference of bottom-up face perception in topdown face processing. Analyzing the map of functional connectivity with right FFA analyzed by conventional Pearson's correlation, a possible face processing pattern induced by top-down perception can be obtained. Apart from the brain areas of bilateral fusiform gyrus (FG), left inferior occipital gyrus (IOG) and left superior temporal sulcus (STS), which are consistent with a core system in the distributed cortical network for face perception, activation induced by top-down face processing is also found in these regions that include the anterior cingulate gyrus (ACC), right oribitofrontal cortex (OFC), left precuneus, right parahippocampal cortex, left dorsolateral prefrontal cortex (DLPFC), right frontal pole, bilateral premotor cortex, left inferior parietal cortex and bilateral thalamus. The results indicate that making-decision, attention, episodic memory retrieving and contextual associative processing network cooperate with general face processing regions to process face information under top-down perception.

  16. Accelerating Atomic Orbital-based Electronic Structure Calculation via Pole Expansion plus Selected Inversion

    Energy Technology Data Exchange (ETDEWEB)

    Lin, Lin; Chen, Mohan; Yang, Chao; He, Lixin

    2012-02-10

    We describe how to apply the recently developed pole expansion plus selected inversion (PEpSI) technique to Kohn-Sham density function theory (DFT) electronic structure calculations that are based on atomic orbital discretization. We give analytic expressions for evaluating charge density, total energy, Helmholtz free energy and atomic forces without using the eigenvalues and eigenvectors of the Kohn-Sham Hamiltonian. We also show how to update the chemical potential without using Kohn-Sham eigenvalues. The advantage of using PEpSI is that it has a much lower computational complexity than that associated with the matrix diagonalization procedure. We demonstrate the performance gain by comparing the timing of PEpSI with that of diagonalization on insulating and metallic nanotubes. For these quasi-1D systems, the complexity of PEpSI is linear with respect to the number of atoms. This linear scaling can be observed in our computational experiments when the number of atoms in a nanotube is larger than a few hundreds. Both the wall clock time and the memory requirement of PEpSI is modest. This makes it even possible to perform Kohn-Sham DFT calculations for 10,000-atom nanotubes on a single processor. We also show that the use of PEpSI does not lead to loss of accuracy required in a practical DFT calculation.

  17. Decoding of faces and face components in face-sensitive human visual cortex

    Directory of Open Access Journals (Sweden)

    David F Nichols

    2010-07-01

    Full Text Available A great challenge to the field of visual neuroscience is to understand how faces are encoded and represented within the human brain. Here we show evidence from functional magnetic resonance imaging (fMRI for spatially distributed processing of the whole face and its components in face-sensitive human visual cortex. We used multi-class linear pattern classifiers constructed with a leave-one-scan-out verification procedure to discriminate brain activation patterns elicited by whole faces, the internal features alone, and the external head outline alone. Furthermore, our results suggest that whole faces are represented disproportionately in the fusiform cortex (FFA whereas the building blocks of faces are represented disproportionately in occipitotemporal cortex (OFA. Faces and face components may therefore be organized with functional clustering within both the FFA and OFA, but with specialization for face components in the OFA and the whole face in the FFA.

  18. Loss Networks

    OpenAIRE

    Kelly, F. P.

    1991-01-01

    This paper describes work on the stochastic modelling of loss networks. Such systems have long been of interest to telephone engineers and are becoming increasingly important as models of computer and information systems. Throughout the century problems from this field have provided an impetus to the development of probability theory, pure and applied. This paper provides an introduction to the area and a review of recent work.

  19. Strategi Pengembangan Daerah Growth Pole melalui Pemanfaatan Potensi Lokal

    Directory of Open Access Journals (Sweden)

    Rusdarti Rusdarti

    2016-12-01

    Full Text Available This research aims to determine the leading sectors that could be developed in each district in Cilacap Regency as a growth pole area. We use location quotient, shift share, and klassen typology as analysis methods. The research results show that not all of the district at Cilacap regency have a leading sector. Further, districts that have leading sectors are as follows. Wanareja only has a leading sector, i.e. agriculture. Secondly, Kawunganten has two leading sectors, agriculture and finance, rent, and company services. Thirdly, Agriculture becomes the only leading sector of Kampung Laut District. Fourthly, Mining and extraction are the leading sectors of Kesugihan District. Fifthly, Sampang District has buildings and finance sectors as the leading sectors. Sixthly, Kroya District leads in trade, hotel, and restaurant sectors. Seventhly, South Cilacap District leads in mining and extraction sectors. Eighthly, Central Cilacap District has manufacturing, electricity, gas and clean water, building and services as leading sectors. Lastly, North Cilacap District has electricity, gas and clean water, manufacturing, building and services as leading sectors. Abstrak   Tujuan dari penelitian ini adalah menentukan sektor unggulan yang dapat dikembangkan di tiap kecamatan di Kabupaten Cilacap sebagai salah satu daerah growth pole. Alat analisis yang digunakan dalam penelitian ini yaitu location quotient, shift share dan klassen typologi. Hasil penelitian menunjukkan tidak semua kecamatan di kabupaten Cilacap memiliki sektor unggulan. Beberapa daerah yang memiliki sektor unggulan diantaranya adalah  Kecamatan Wanareja hanya memiliki satu sektor unggulan yaitu pertanian. Kedua adalah Kecamatan Kawunganten memiliki dua sektor unggulan yaitu sektor pertanian dan sektor keuangan, persewaan dan jasa perusahaan. Kecamatan Kampung Laut, dimana sektor pertanian pada kecamatan ini sangatlah unggul. Kecamatan kesugihan juga memiliki satu sektor unggulan yaitu

  20. Linking Atmospheric Pollution to Cryospheric Changes over the Third Pole

    Science.gov (United States)

    Kang, S.; Zhang, Q.; Ji, Z.; Li, Y.; Chen, J.; Zhang, G.; Li, C.; Cong, Z.; Chen, P.; Guo, J.; Huang, J.; Tripathee, L.; Rupakheti, D.; Li, X.; Zhang, Y.; Panday, A. K.; Rupakheti, M.

    2016-12-01

    Known as "the Third Pole" (TP), the Tibetan Plateau and surrounding mountains hold the largest aggregate of glaciers outside the pole regions. Recent monitoring and projection indicated an accelerated glacier decline and increasing glacier runoff. The long-range transport of South Asian atmospheric pollutants, including light absorbing impurities (LAIs) such as black carbon (BC) and mineral dust (MD), can absorb the solar radiation in the atmosphere and reduce albedo after being deposited onto the cryosphere, thereby promoting glacier and snow melt. A coordinated atmospheric pollution monitoring network has been launched covering the TP with emphasis on trans-Himalayan transects since 2013. TSP were collected for 24h at an interval of 3-6 days. BC/OC, polycyclic aromatic hydrocarbons (PAHs) and heavy metals were measured. Results reveal a consistent decrease in almost all analyzed parameters from south to north across the Himalayas. Geochemical signatures of carbonaceous aerosols indicate dominant sources of biomass burning and vehicle exhaust, in line with results of PAHs. Integrated analysis of satellite images and air mass trajectories suggest that the trans-boundary air pollution occurred episodically and concentrated in pre-monsoon seasons via upper air circulation, through-valley wind, and local convection. Simulation results showed that carbonaceous aerosols produced positive/negative shortwave radiative forcing in the atmosphere/ground surface. Aerosols increased surface air temperatures by 0.1-0.5° over the TP and decreased temperatures in South Asia during the monsoon season. Surface snow/ice samples were collected from benchmark glaciers to estimate the impacts of LAIs on glacier melt with model assistance. BC (37%) and MD (32%) contribute to the summer melting of Laohugou Glacier in the northern TP. MD (38%) contributed more glacier melt than BC (11%) on Zhadang Glacier in the southern TP. In the southeastern TP, BC and MD contribute to 30% of the

  1. Searching for Terrain Softening near Mercury's North Pole

    Science.gov (United States)

    Cobian, P. S.; Vilas, F.; Lederer, S. M.; Barlow, N. G.

    2004-01-01

    In 1999, following the initial discovery of radar bright craters near both poles of Mercury measured the depth-todiameter (d/D) ratios of 170 impact craters in Mariner 10 images covering four different regions on Mercury s surface. Rapid softening of crater structure, indicated by lower d/D ratios, could indicate the possibility of subsurface water ice in Mercury's terrain originating from an internal source in the planet. Their study included 3 specific radar bright craters suggested to contain ice. They concluded that no terrain softening was apparent, and a rapidly emplaced exogenic water source was the most likely source for the proposed ice in these craters. Recent radar observations of the Mercurian North pole have pinpointed many additional radar bright areas with a resolution 10x better than previous radar measurements, and which correlate with craters imaged by Mariner 10. These craters are correlated with regions that are permanently shaded from direct sunlight, and are consistent with observations of clean water ice. We have expanded the initial study by Barlow et al. to include d/D measurements of 12 craters newly identified as radar bright at latitudes poleward of +80o. The radar reflectivity resemblances to Mars south polar cap and echoes from three icy Galilean satellites suggest that these craters too may have polar ice on Mercury. The effect of subsurface H20 on impact craters is a decrease in its d/D ratio, and softening of crater rims over a period of time. The study of Barlow et al., focused on determining the d/D ratios of 170 impact craters in the Borealis (north polar), Tolstoj (equatorial), Kuiper (equatorial), and Bach (south polar) quadrangles. This work focuses on the newly discovered radar bright craters, investigating their d/D ratios as an expansion of the earlier work..We compare our results to the statistical results from Barlow et al. here. With the upcoming Messenger spacecraft mission to Mercury, this is an especially timely study

  2. High-mast light poles anchor nut loosening in Alaska : an investigation of field monitoring and finite-element analysis.

    Science.gov (United States)

    2014-09-01

    High mast lighting poles (HMLPs) are tall, roadside structures effective for lighting large areas of highways and intersections. The Alaska Department of Transportation : and Public Facilities (AKDOT&PF) maintains 118 such poles in the greater Anchor...

  3. Faced with a dilemma

    DEFF Research Database (Denmark)

    Christensen, Anne Vinggaard; Christiansen, Anne Hjøllund; Petersson, Birgit

    2013-01-01

    's legal right to choose TOP and considerations about the foetus' right to live were suppressed. Midwives experienced a dilemma when faced with aborted foetuses that looked like newborns and when aborted foetuses showed signs of life after a termination. Furthermore, they were critical of how physicians...... counsel women/couples after prenatal diagnosis. CONCLUSIONS: The midwives' practice in relation to late TOP was characterised by an acknowledgement of the growing ethical status of the foetus and the emotional reactions of the women/couples going through late TOP. Other professions as well as structural...

  4. Assessing Students Perceptions on Intensive Face to Face in Open ...

    African Journals Online (AJOL)

    Therefore, this study assessed students‟ perception on Intensive Face to Face sessions. The study specifically aimed at identifying students‟ perception on quality of interaction between tutors and students and between students on the other hand. It also explored the nature of challenges students meet in attending face to ...

  5. Face reconstruction from image sequences for forensic face comparison

    NARCIS (Netherlands)

    van Dam, C.; Veldhuis, Raymond N.J.; Spreeuwers, Lieuwe Jan

    2016-01-01

    The authors explore the possibilities of a dense model-free three-dimensional (3D) face reconstruction method, based on image sequences from a single camera, to improve the current state of forensic face comparison. They propose a new model-free 3D reconstruction method for faces, based on the

  6. Facing scalability: Naming faces in an online social network

    NARCIS (Netherlands)

    Poppe, Ronald Walter

    Automatically naming faces in online social networks enables us to search for photos and build user face models. We consider two common weakly supervised settings where: (1) users are linked to photos, not to faces and (2) photos are not labeled but part of a user's album. The focus is on algorithms

  7. Face-to-Face Interference in Typical and Atypical Development

    Science.gov (United States)

    Riby, Deborah M.; Doherty-Sneddon, Gwyneth; Whittle, Lisa

    2012-01-01

    Visual communication cues facilitate interpersonal communication. It is important that we look at faces to retrieve and subsequently process such cues. It is also important that we sometimes look away from faces as they increase cognitive load that may interfere with online processing. Indeed, when typically developing individuals hold face gaze…

  8. Thermal to visible face recognition

    Science.gov (United States)

    Choi, Jonghyun; Hu, Shuowen; Young, S. Susan; Davis, Larry S.

    2012-06-01

    In low light conditions, visible light face identification is infeasible due to the lack of illumination. For nighttime surveillance, thermal imaging is commonly used because of the intrinsic emissivity of thermal radiation from the human body. However, matching thermal images of faces acquired at nighttime to the predominantly visible light face imagery in existing government databases and watch lists is a challenging task. The difficulty arises from the significant difference between the face's thermal signature and its visible signature (i.e. the modality gap). To match the thermal face to the visible face acquired by the two different modalities, we applied face recognition algorithms that reduce the modality gap in each step of face identification, from low-level analysis to machine learning techniques. Specifically, partial least squares-discriminant analysis (PLS-DA) based approaches were used to correlate the thermal face signatures to the visible face signatures, yielding a thermal-to-visible face identification rate of 49.9%. While this work makes progress for thermal-to-visible face recognition, more efforts need to be devoted to solving this difficult task. Successful development of a thermal-to-visible face recognition system would significantly enhance the Nation's nighttime surveillance capabilities.

  9. ITER plasma facing components

    International Nuclear Information System (INIS)

    Kuroda, T.; Vieider, G.; Akiba, M.

    1991-01-01

    This document summarizes results of the Conceptual Design Activities (1988-1990) for the International Thermonuclear Experimental Reactor (ITER) project, namely those that pertain to the plasma facing components of the reactor vessel, of which the main components are the first wall and the divertor plates. After an introduction and an executive summary, the principal functions of the plasma-facing components are delineated, i.e., (i) define the low-impurity region within which the plasma is produced, (ii) absorb the electromagnetic radiation and charged-particle flux from the plasma, and (iii) protect the blanket/shield components from the plasma. A list of critical design issues for the divertor plates and the first wall is given, followed by discussions of the divertor plate design (including the issues of material selection, erosion lifetime, design concepts, thermal and mechanical analysis, operating limits and overall lifetime, tritium inventory, baking and conditioning, safety analysis, manufacture and testing, and advanced divertor concepts) and the first wall design (armor material and design, erosion lifetime, overall design concepts, thermal and mechanical analysis, lifetime and operating limits, tritium inventory, baking and conditioning, safety analysis, manufacture and testing, an alternative first wall design, and the limiters used instead of the divertor plates during start-up). Refs, figs and tabs

  10. Atmospheric Fluctuations in the Millimeter Wavelength at the South Pole

    Science.gov (United States)

    Bussmann, R. S.; Holzapfel, W.; Kuo, C. L.

    2003-12-01

    We characterize atmospheric fluctuations by a Kolmogorov power law around the South pole at Millimeter wavelengths by calculating the correlation between signals coming from two separate channels in a detector array. We use data taken with the ACBAR instrument mounted on the Viper telescope over the winter period beginning in April 2002 and ending in August 2002 to generate a model of the atmospheric fluctuations. We use this model to obtain values for the amplitude of the atmospheric fluctuations as well as the angular windspeed causing the movement of the disturbances which are responsible for the emission we observe. The primary benefit of the correlation analysis is to significantly reduce contribution from instrument noise, which is uncorrelated between two channels. Thus we are able to perform a very reliable characterization of the atmosphere. ACBAR was supported by funds from the Center for Astrophysical Research in Antarctica, a National Science Foundation Science and Technology Center. Operational support was provided by the United States Antarctic Program.

  11. The North Galactic Pole Rift and the Local Hot Bubble

    Science.gov (United States)

    Snowden, S. L.; Koutroumpa, D.; Kuntz, K. D.; Lallement, R.; Puspitarini, L.

    2015-01-01

    The North Galactic Pole Rift (NGPR) is one of the few distinct neutral hydrogen clouds at high Galactic latitudes that have well-defined distances. It is located at the edge of the Local Cavity (LC) and provides an important test case for understanding the Local Hot Bubble (LHB), the presumed location for the hot diffuse plasma responsible for much of the observed 1/4 keV emission originating in the solar neighborhood. Using data from the ROSAT All- Sky Survey and the Planck reddening map, we find the path length within the LC (LHB plus Complex of Local Interstellar Clouds) to be 98 plus or minus 27 pc, in excellent agreement with the distance to the NGPR of 98 +/- 6 pc. In addition, we examine another 14 directions that are distributed over the sky where the LC wall is apparently optically thick at 1/4 keV. We find that the data in these directions are also consistent with the LHB model and a uniform emissivity plasma filling most of the LC.

  12. India plans to land near moon's south pole

    Science.gov (United States)

    Bagla, Pallava

    2018-02-01

    Sometime this summer, an Indian spacecraft orbiting over the moon's far side will release a lander. The craft will ease to a soft landing just after lunar sunrise on an ancient, table-flat plain about 600 kilometers from the south pole. There, it will unleash a rover into territory never before explored at the surface. That's the ambitious vision for India's second voyage to the moon in a decade, due to launch in the coming weeks. If Chandrayaan-2 is successful, it will pave the way for even more ambitious Indian missions, such as landings on Mars and an asteroid, as well as a Venus probe. Lunar scientists have much at stake, too. Chandrayaan-2 will collect data on the moon's thin envelope of plasma, as well as isotopes such as helium-3, a potential fuel for future fusion energy reactors. And it will follow up on a stunning discovery by India's first lunar foray, which found water molecules on the moon in 2009.

  13. Resonances and poles in isoscattering microwave networks and graphs.

    Science.gov (United States)

    Ławniczak, Michał; Sawicki, Adam; Bauch, Szymon; Kuś, Marek; Sirko, Leszek

    2014-03-01

    Can one hear the shape of a graph? This is a modification of the famous question of Mark Kac "Can one hear the shape of a drum?" which can be asked in the case of scattering systems such as quantum graphs and microwave networks. It addresses an important mathematical problem whether scattering properties of such systems are uniquely connected to their shapes? Recent experimental results based on a characteristics of graphs such as the cumulative phase of the determinant of the scattering matrices indicate a negative answer to this question [O. Hul, M. Ławniczak, S. Bauch, A. Sawicki, M. Kuś, and L. Sirko, Phys. Rev. Lett. 109, 040402 (2012)]. In this paper we consider important local characteristics of graphs such as structures of resonances and poles of the determinant of the scattering matrices. Using these characteristics we study experimentally and theoretically properties of graphs and directly confirm that the pair of graphs considered in the cited paper is isoscattering. The experimental results are compared to the theoretical ones for a broad frequency range from 0.01 to 3 GHz. In the numerical calculations of the resonances of the graphs absorption present in the experimental networks is taken into account.

  14. Resource Prospector: Evaluating the ISRU Potential of the Lunar Poles

    Science.gov (United States)

    Colaprete, A.; Elphic, R. C.; Andrews, D.; Bluethmann, W.; Quinn, J.; Chavers, D. G.

    2017-12-01

    Resource Prospector (RP) is a lunar volatiles prospecting mission being developed for potential flight in CY2021-2022. The mission includes a rover-borne payload that (1) can locate surface and near-subsurface volatiles, (2) excavate and analyze samples of the volatile-bearing regolith, and (3) demonstrate the form, extractability and usefulness of the materials. The primary mission goal for RP is to evaluate the In-Situ Resource Utilization (ISRU) potential of the lunar poles. While it is now understood that lunar water and other volatiles have a much greater extent of distribution, possible forms, and concentrations than previously believed, to fully understand how viable these volatiles are as a resource to support human exploration of the solar system, the distribution and form needs to be understood at a "human" scale. That is, the "ore body" must be better understood at the scales it would be worked before it can be evaluated as a potential architectural element within any evolvable lunar or Mars campaign. This talk will provide an overview of the RP mission with an emphasis on mission goals and measurements, and will provide an update as to its current status.

  15. Inconspicuous portable audio/visual recording: transforming an IV pole into a mobile video capture stand.

    Science.gov (United States)

    Pettineo, Christopher M; Vozenilek, John A; Kharasch, Morris; Wang, Ernest; Aitchison, Pam; Arreguin, Andrew

    2008-01-01

    Although a traditional simulation laboratory may have excellent installed audio/visual capabilities, often large classes overwhelm the limited space in the laboratory. With minimal monetary investment, it is possible to create a portable audio/visual stand from an old IV pole. An IV pole was transformed into an audio/visual stand to overcome the burden of transporting individual electronic components during a patient safety research project conducted in an empty patient room with a standardized patient. The materials and methods for making the modified IV pole are outlined in this article. The limiting factor of production is access to an old IV pole; otherwise a few purchases from an electronics store complete the audio/visual IV pole. The modified IV pole is a cost-effective and portable solution to limited space or the need for audio/visual capabilities outside of a simulation laboratory. The familiarity of an IV pole in a clinical setting reduces the visual disturbance of relocated audio/visual equipment in a room previously void of such instrumentation.

  16. EVOLUTION OF THE FAR-INFRARED CLOUD AT TITAN’S SOUTH POLE

    Energy Technology Data Exchange (ETDEWEB)

    Jennings, Donald E.; Achterberg, R. K.; Cottini, V.; Anderson, C. M.; Flasar, F. M.; Nixon, C. A.; Bjoraker, G. L.; Kunde, V. G.; Carlson, R. C.; Guandique, E.; Kaelberer, M. S.; Tingley, J. S.; Albright, S. A.; Segura, M. E. [Goddard Space Flight Center, Greenbelt, MD 20771 (United States); Kok, R. de [SRON Netherlands Institute for Space Research, Sorbonnelaan 2, 3584 CA Utrecht (Netherlands); Coustenis, A.; Vinatier, S.; Bampasidis, G. [Laboratoire d’Etudes Spatiales et d’Instrumentation en Astrophysique (LESIA), Observatoire de Paris, CNRS, UPMC Univ. Paris 06, Univ. Paris-Diderot, 5, place Jules Janssen, F-92195 Meudon Cedex (France); Teanby, N. A. [School of Earth Sciences, University of Bristol, Bristol BS8 1RJ (United Kingdom); Calcutt, S., E-mail: donald.e.jennings@nasa.gov [Department of Physics, University of Oxford, Parks Road, Oxford OX1 3PU (United Kingdom)

    2015-05-10

    A condensate cloud on Titan identified by its 220 cm{sup −1} far-infrared signature continues to undergo seasonal changes at both the north and south poles. In the north, the cloud, which extends from 55 N to the pole, has been gradually decreasing in emission intensity since the beginning of the Cassini mission with a half-life of 3.8 years. The cloud in the south did not appear until 2012 but its intensity has increased rapidly, doubling every year. The shape of the cloud at the south pole is very different from that in the north. Mapping in 2013 December showed that the condensate emission was confined to a ring with a maximum at 80 S. The ring was centered 4° from Titan's pole. The pattern of emission from stratospheric trace gases like nitriles and complex hydrocarbons (mapped in 2014 January) was also offset by 4°, but had a central peak at the pole and a secondary maximum in a ring at about 70 S with a minimum at 80 S. The shape of the gas emission distribution can be explained by abundances that are high at the atmospheric pole and diminish toward the equator, combined with correspondingly increasing temperatures. We discuss possible causes for the condensate ring. The present rapid build up of the condensate cloud at the south pole is likely to transition to a gradual decline from 2015 to 2016.

  17. Interaction between Poly(ADP-ribose) and NuMA contributes to mitotic spindle pole assembly.

    Science.gov (United States)

    Chang, Paul; Coughlin, Margaret; Mitchison, Timothy J

    2009-11-01

    Poly(ADP-ribose) (pADPr), made by PARP-5a/tankyrase-1, localizes to the poles of mitotic spindles and is required for bipolar spindle assembly, but its molecular function in the spindle is poorly understood. To investigate this, we localized pADPr at spindle poles by immuno-EM. We then developed a concentrated mitotic lysate system from HeLa cells to probe spindle pole assembly in vitro. Microtubule asters assembled in response to centrosomes and Ran-GTP in this system. Magnetic beads coated with pADPr, extended from PARP-5a, also triggered aster assembly, suggesting a functional role of the pADPr in spindle pole assembly. We found that PARP-5a is much more active in mitosis than interphase. We used mitotic PARP-5a, self-modified with pADPr chains, to capture mitosis-specific pADPr-binding proteins. Candidate binding proteins included the spindle pole protein NuMA previously shown to bind to PARP-5a directly. The rod domain of NuMA, expressed in bacteria, bound directly to pADPr. We propose that pADPr provides a dynamic cross-linking function at spindle poles by extending from covalent modification sites on PARP-5a and NuMA and binding noncovalently to NuMA and that this function helps promote assembly of exactly two poles.

  18. Tribos urbanas e identidades nas metrópoles

    Directory of Open Access Journals (Sweden)

    Márcia Regina da Costa

    2001-01-01

    Full Text Available This article aims to face the issue of urban tribes and the construction of identities. The text starts from analyses made by different authors about the society we are part of and goes on by a theoretical assessment of the issue. Among others, are used contributions of Berman, Balandier, Mafessoli, Giddens, Costa, Tornero & Tropea e Castells.

  19. Effect of PF impregnation and surface densification on the mechanical properties of small-scale wood laminated poles

    Science.gov (United States)

    Huaqiang Yu; Chung Y. Hse; Zehui Jiang

    2009-01-01

    The wood poles in the United States are from high-valued trees that are becoming more expensive and less available. Wood laminated composite poles (LCP) are a kind of alternative to solid poles. Considerable interest has developed in last century in the resin impregnation and wood surface densification to improve its physical and mechanical properties. In this...

  20. Structural behaviour of concrete poles used in electric's power distribution network

    Directory of Open Access Journals (Sweden)

    Mehran Zeynalian

    2017-12-01

    Full Text Available Based on a preliminary study on regional electric companies, it is shown that there is no precise structural design on the concrete poles. This leads to uneconomical and overestimated networks’ components. Therefore, this study was aimed to investigate the lateral performance of the concrete poles which are employed in electric’s power distribution network. This paper presents a numerical study on structural performance of 12 m concrete poles used in electric’s power distribution network using Abaqus software. A sensitivity study for mesh size is carried out and concrete damaged plasticity has been employed. The results show that relatively coarse mesh (average in damaged concrete method gives more reliable result. Some experimental tests based on the Iranian standards were performed in order to make a bench mark for numerical output. Comparison between numerical and experimental results indicates a good agreement between the results. The outcomes also suggest that while the applied lateral load is less than around 400 kg which is assumed as the nominal resistance of the pole, no transverse crack occurs. Based on both experimental and numerical results, one or two transverse cracks are reported when the applied force reaches up to 600 kg. The rate of cracks is amplified by increasing the applied force; and finally, the pole would lose its capacity when the load rises much more than 1200 kg. The study also shows that the poles are very weak when the load direction changes. Also, it can be concluded that the final strength of the pole is higher than what the standards recommend. Finally, seismic behavior factor of the poles around both main axes are evaluated. The estimated seismic resistance factor for the concrete poles indicates that the prescribed R factor for such structure is relatively low; and can be improved at least 20%.

  1. Integrated 3D printing and corona poling process of PVDF piezoelectric films for pressure sensor application

    Science.gov (United States)

    Kim, Hoejin; Torres, Fernando; Wu, Yanyu; Villagran, Dino; Lin, Yirong; Tseng, Tzu-Liang(Bill

    2017-08-01

    This paper presents a novel process to fabricate piezoelectric films from polyvinylidene fluoride (PVDF) polymer using integrated fused deposition modeling (FDM) 3D printing and corona poling technique. Corona poling is one of many effective poling processes that has received attention to activate PVDF as a piezoelectric responsive material. The corona poling process occurs when a PVDF polymer is exposed to a high electric field created and controlled through an electrically charged needle and a grid electrode under heating environment. FDM 3D printing has seen extensive progress in fabricating thermoplastic materials and structures, including PVDF. However, post processing techniques such as poling is needed to align the dipoles in order to gain piezoelectric properties. To further simplify the piezoelectric sensors and structures fabrication process, this paper proposes an integrated 3D printing process with corona poling to fabricate piezoelectric PVDF sensors without post poling process. This proposed process, named ‘Integrated 3D Printing and Corona poling process’ (IPC), uses the 3D printer’s nozzle and heating bed as anode and cathode, respectively, to create poling electric fields in a controlled heating environment. The nozzle travels along the programmed path with fixed distance between nozzle tip and sample’s top surface. Simultaneously, the electric field between the nozzle and bottom heating pad promotes the alignment of dipole moment of PVDF molecular chains. The crystalline phase transformation and output current generated by printed samples under different electric fields in this process were characterized by a Fourier transform infrared spectroscopy and through fatigue load frame. It is demonstrated that piezoelectric PVDF films with enhanced β-phase percentage can be fabricated using the IPC process. In addition, mechanical properties of printed PVDF was investigated by tensile testing. It is expected to expand the use of additive

  2. De Nápoles a Beijing, (1799-1995. Dos siglos de mujeres y paz

    Directory of Open Access Journals (Sweden)

    Montserrat Huguet Santos

    2011-12-01

    En este texto se apunta la evolución contemporánea de la relación entre la paz ¿anverso de la guerra¿ y las mujeres. A este fin se han considerado dos momentos de tránsito: el Nápoles de la República Partenopea (1799 y el Beijing de la IV Conferencia Internacional de Mujeres (1995, que solo son pretextos, metáforas espacio¿temporales para una narración en la que el tema central es en primer lugar la atracción contemporánea entre mujeres y paz; en segundo, las dificultades históricas a las que ha tenido que hacer frente este particular binomio, y el último término, la normalización por fin de una tendencia universal, apreciable especialmente en los dos últimos siglos. History teaches us that are women in general those who opposed to the wars. This text shows the contemporary evolution of the relation between peace – opposite of war – and women. To this end there have been considered two moments of change: the Naples of the Parthenopean Republic (1799 and the Beijing of the Fourth World Conference on Women (1995, that are only pretexts, metaphors of time and place for a narrative in which the main topic is, firstly, the contemporary attraction between women and peace; secondly, the historical difficulties that this particular binomial has had to face; finally, the normalization, at last, of a universal tendency, specially appreciable over the last two centuries.

  3. Ripple Field AC Losses in 10-MW Wind Turbine Generators With a MgB2 Superconducting Field Winding

    DEFF Research Database (Denmark)

    Liu, Dong; Polinder, Henk; Magnusson, Niklas

    2016-01-01

    with different numbers of slots per pole per phase. The necessity of an electromagnetic shield is then discussed based on the obtained loss levels. The results show that the total ac loss is so small that ferromagnetic teeth can be applied in the generator design without using an electromagnetic shield....

  4. Matching score based face recognition

    NARCIS (Netherlands)

    Boom, B.J.; Beumer, G.M.; Spreeuwers, Lieuwe Jan; Veldhuis, Raymond N.J.

    2006-01-01

    Accurate face registration is of vital importance to the performance of a face recognition algorithm. We propose a new method: matching score based face registration, which searches for optimal alignment by maximizing the matching score output of a classifier as a function of the different

  5. Forensic Face Recognition: A Survey

    NARCIS (Netherlands)

    Ali, Tauseef; Spreeuwers, Lieuwe Jan; Veldhuis, Raymond N.J.; Quaglia, Adamo; Epifano, Calogera M.

    2012-01-01

    The improvements of automatic face recognition during the last 2 decades have disclosed new applications like border control and camera surveillance. A new application field is forensic face recognition. Traditionally, face recognition by human experts has been used in forensics, but now there is a

  6. Enabling dynamics in face analysis

    NARCIS (Netherlands)

    Dibeklioğlu, H.

    2014-01-01

    Most of the approaches in automatic face analysis rely solely on static appearance. However, temporal analysis of expressions reveals interesting patterns. For a better understanding of the human face, this thesis focuses on temporal changes in the face, and dynamic patterns of expressions. In

  7. Side-View Face Recognition

    NARCIS (Netherlands)

    Santemiz, P.; Spreeuwers, Lieuwe Jan; Veldhuis, Raymond N.J.

    2010-01-01

    Side-view face recognition is a challenging problem with many applications. Especially in real-life scenarios where the environment is uncontrolled, coping with pose variations up to side-view positions is an important task for face recognition. In this paper we discuss the use of side view face

  8. Least 1-Norm Pole-Zero Modeling with Sparse Deconvolution for Speech Analysis

    DEFF Research Database (Denmark)

    Shi, Liming; Jensen, Jesper Rindom; Christensen, Mads Græsbøll

    2017-01-01

    In this paper, we present a speech analysis method based on sparse pole-zero modeling of speech. Instead of using the all-pole model to approximate the speech production filter, a pole-zero model is used for the combined effect of the vocal tract; radiation at the lips and the glottal pulse shape......-zero, linear prediction and sparse linear prediction methods, experimental results show that the proposed speech analysis method has lower spectral distortion, higher reconstruction SNR and sparser residuals....

  9. Frequent POLE1 p.S297F mutation in Chinese patients with ovarian endometrioid carcinoma

    International Nuclear Information System (INIS)

    Zou, Yang; Liu, Fa-Ying; Liu, Huai; Wang, Feng; Li, Wei; Huang, Mei-Zhen; Huang, Yan; Yuan, Xiao-Qun; Xu, Xiao-Yun; Huang, Ou-Ping; He, Ming

    2014-01-01

    The catalytic subunit of DNA polymerase epsilon (POLE1) functions primarily in nuclear DNA replication and repair. Recently, POLE1 mutations were detected frequently in colorectal and endometrial carcinomas while with lower frequency in several other types of cancer, and the p.P286R and p.V411L mutations were the potential mutation hotspots in human cancers. Nevertheless, the mutation frequency of POLE1 in ovarian cancer still remains largely unknown. Here, we screened a total of 251 Chinese samples with distinct subtypes of ovarian carcinoma for the presence of POLE1 hotspot mutations by direct sequencing. A heterozygous somatic POLE1 mutation, p.S297F (c.890C>T), but not p.P286R and p.V411L hotspot mutations observed in other cancer types, was identified in 3 out of 37 (8.1%) patients with ovarian endometrioid carcinoma; this mutation was evolutionarily highly conserved from Homo sapiens to Schizosaccharomyces. Of note, the POLE1 mutation coexisted with mutation in the ovarian cancer-associated PPP2R1A (protein phosphatase 2, regulatory subunit A, α) gene in a 46-year-old patient, who was also diagnosed with ectopic endometriosis in the benign ovary. In addition, a 45-year-old POLE1-mutated ovarian endometrioid carcinoma patient was also diagnosed with uterine leiomyoma while the remaining 52-year-old POLE1-mutated patient showed no additional distinctive clinical manifestation. In contrast to high frequency of POLE1 mutations in ovarian endometrioid carcinoma, no POLE1 mutations were identified in patients with other subtypes of ovarian carcinoma. Our results showed for the first time that the POLE1 p.S297F mutation, but not p.P286R and p.V411L hotspot mutations observed in other cancer types, was frequent in Chinese ovarian endometrioid carcinoma, but absent in other subtypes of ovarian carcinoma. These results implicated that POLE1 p.S297F mutation might be actively involved in the pathogenesis of ovarian endometrioid carcinoma, but might not be actively

  10. Frequent POLE1 p.S297F mutation in Chinese patients with ovarian endometrioid carcinoma

    Energy Technology Data Exchange (ETDEWEB)

    Zou, Yang; Liu, Fa-Ying; Liu, Huai; Wang, Feng [Key Laboratory of Women' s Reproductive Health of Jiangxi Province, Jiangxi Provincial Maternal and Child Health Hospital, Nanchang, Jiangxi 330006 (China); Central Laboratory, Jiangxi Provincial Maternal and Child Health Hospital, Nanchang, Jiangxi 330006 (China); Li, Wei [Key Laboratory of Women' s Reproductive Health of Jiangxi Province, Jiangxi Provincial Maternal and Child Health Hospital, Nanchang, Jiangxi 330006 (China); Central Laboratory, Jiangxi Provincial Maternal and Child Health Hospital, Nanchang, Jiangxi 330006 (China); Graduate School of Nanchang University, Nanchang, Jiangxi 330031 (China); Huang, Mei-Zhen [Graduate School of Nanchang University, Nanchang, Jiangxi 330031 (China); Jiangxi Provincial Cancer Institute, Jiangxi Provincial Cancer Hospital, Nanchang, Jiangxi 330029 (China); Huang, Yan; Yuan, Xiao-Qun [Key Laboratory of Women' s Reproductive Health of Jiangxi Province, Jiangxi Provincial Maternal and Child Health Hospital, Nanchang, Jiangxi 330006 (China); Central Laboratory, Jiangxi Provincial Maternal and Child Health Hospital, Nanchang, Jiangxi 330006 (China); Graduate School of Nanchang University, Nanchang, Jiangxi 330031 (China); Xu, Xiao-Yun [Graduate School of Nanchang University, Nanchang, Jiangxi 330031 (China); Jiangxi Provincial Cancer Institute, Jiangxi Provincial Cancer Hospital, Nanchang, Jiangxi 330029 (China); Huang, Ou-Ping, E-mail: huangouping@gmail.com [Jiangxi Provincial Cancer Institute, Jiangxi Provincial Cancer Hospital, Nanchang, Jiangxi 330029 (China); He, Ming, E-mail: jxhm56@hotmail.com [Department of Pharmacology and Molecular Therapeutics, Nanchang University School of Pharmaceutical Science, Nanchang 330006 (China)

    2014-03-15

    The catalytic subunit of DNA polymerase epsilon (POLE1) functions primarily in nuclear DNA replication and repair. Recently, POLE1 mutations were detected frequently in colorectal and endometrial carcinomas while with lower frequency in several other types of cancer, and the p.P286R and p.V411L mutations were the potential mutation hotspots in human cancers. Nevertheless, the mutation frequency of POLE1 in ovarian cancer still remains largely unknown. Here, we screened a total of 251 Chinese samples with distinct subtypes of ovarian carcinoma for the presence of POLE1 hotspot mutations by direct sequencing. A heterozygous somatic POLE1 mutation, p.S297F (c.890C>T), but not p.P286R and p.V411L hotspot mutations observed in other cancer types, was identified in 3 out of 37 (8.1%) patients with ovarian endometrioid carcinoma; this mutation was evolutionarily highly conserved from Homo sapiens to Schizosaccharomyces. Of note, the POLE1 mutation coexisted with mutation in the ovarian cancer-associated PPP2R1A (protein phosphatase 2, regulatory subunit A, α) gene in a 46-year-old patient, who was also diagnosed with ectopic endometriosis in the benign ovary. In addition, a 45-year-old POLE1-mutated ovarian endometrioid carcinoma patient was also diagnosed with uterine leiomyoma while the remaining 52-year-old POLE1-mutated patient showed no additional distinctive clinical manifestation. In contrast to high frequency of POLE1 mutations in ovarian endometrioid carcinoma, no POLE1 mutations were identified in patients with other subtypes of ovarian carcinoma. Our results showed for the first time that the POLE1 p.S297F mutation, but not p.P286R and p.V411L hotspot mutations observed in other cancer types, was frequent in Chinese ovarian endometrioid carcinoma, but absent in other subtypes of ovarian carcinoma. These results implicated that POLE1 p.S297F mutation might be actively involved in the pathogenesis of ovarian endometrioid carcinoma, but might not be actively

  11. Semiclassical approach to Regge poles trajectories calculations for nonsingular potentials: Thomas-Fermi type

    International Nuclear Information System (INIS)

    Belov, S M; Avdonina, N B; Felfli, Z; Marletta, M; Msezane, A Z; Naboko, S N

    2004-01-01

    A simple semiclassical approach, based on the investigation of anti-Stokes line topology, is presented for calculating Regge poles for nonsingular (Thomas-Fermi type) potentials, namely potentials with singularities at the origin weaker than order -2. The anti-Stokes lines for Thomas-Fermi potentials have a more complicated structure than those of singular potentials and require careful application of complex analysis. The explicit solution of the Bohr-Sommerfeld quantization condition is used to obtain approximate Regge poles. We introduce and employ three hypotheses to obtain several terms of the Regge pole approximation

  12. High-resolution second-harmonic microscopy of poled silica waveguides

    DEFF Research Database (Denmark)

    Beermann, Jonas; Bozhevolnyi, Sergey I.; Pedersen, Kjeld

    2003-01-01

    A second-harmonic scanning optical microscopy (SHSOM) apparatus operating in reflection is used for high-resolution imaging of second-order optical non-linearities (SONs) in electric-field poled silica-based waveguides. SHSOM of domain walls in a periodically poled KTiOPO4 crystal is performed......, and the spatial resolution at the pump wavelength of 790 nm is determined to be better than 0.7 m. SHSOM images of positively poled silica waveguides were obtained for different polarization combinations of the incident pump beam and the detected second-harmonic radiation. Calibration of the SHSOM with a GaAs-sample...

  13. Integrated fiber Michelson interferometer based on poled hollow twin-core fiber.

    Science.gov (United States)

    Liu, Zhihai; Bo, Fusen; Wang, Lei; Tian, Fengjun; Yuan, Libo

    2011-07-01

    We propose an integrated fiber Michelson interferometer based on a poled hollow twin-core fiber. The Michelson interferometer can be used as an electro-optic modulator by thermal poling one core of the twin-core fiber and introducing second-order nonlinearity in the fiber. The proposed fiber Michelson interferometer is experimentally demonstrated under driving voltages at the frequency range of 149 to 1000 Hz. The half-wave voltage of the poled fiber is 135 V, and the effective second-order nonlinear coefficient χ² is 1.23 pm/V.

  14. Raman probes based on optically-poled double-clad fiber and coupler

    DEFF Research Database (Denmark)

    Brunetti, Anna Chiara; Margulis, Walter; Rottwitt, Karsten

    2012-01-01

    Two fiber Raman probes are presented, one based on an optically-poled double-clad fiber and the second based on an optically-poled double-clad fiber coupler respectively. Optical poling of the core of the fiber allows for the generation of enough 532nm light to perform Raman spectroscopy...... of a sample of dimethyl sulfoxide (DMSO), when illuminating the waveguide with 1064nm laser light. The Raman signal is collected in the inner cladding, from which it is retrieved with either a bulk dichroic mirror or a double-clad fiber coupler. The coupler allows for a substantial reduction of the fiber...

  15. Face-to-face versus remote and web 2.0 interventions for promoting physical activity.

    Science.gov (United States)

    Richards, Justin; Thorogood, Margaret; Hillsdon, Melvyn; Foster, Charles

    2013-09-30

    Face-to-face interventions for promoting physical activity (PA) are continuing to be popular as remote and web 2.0 approaches rapidly emerge, but we are unsure which approach is more effective at achieving long term sustained change. To compare the effectiveness of face-to-face versus remote and web 2.0 interventions for PA promotion in community dwelling adults (aged 16 years and above). We searched CENTRAL, MEDLINE, EMBASE, CINAHL, and some other databases (from earliest dates available to October 2012). Reference lists of relevant articles were checked. No language restrictions were applied. Randomised trials that compared face-to-face versus remote and web 2.0 PA interventions for community dwelling adults. We included studies if they compared an intervention that was principally delivered face-to-face to an intervention that had principally remote and web 2.0 methods. To assess behavioural change over time, the included studies had a minimum of 12 months follow-up from the start of the intervention to the final results. We excluded studies that had more than a 20% loss to follow-up if they did not apply an intention-to-treat analysis. At least two review authors independently assessed the quality of each study and extracted the data. Non-English language papers were reviewed with the assistance of an interpreter who was an epidemiologist. Study authors were contacted for additional information where necessary. Standardised mean differences (SMDs) and 95% confidence intervals (CIs) were calculated for continuous measures of cardio-respiratory fitness. One study recruiting 225 apparently healthy adults met the inclusion criteria. This study took place in a high-income country. From 27,299 hits, the full texts of 193 papers were retrieved for examination against the inclusion criteria. However, there was only one paper that met the inclusion criteria. This study reported the effect of a PA intervention on cardio-respiratory fitness. There were no reported data

  16. Multipolar spindle pole coalescence is a major source of kinetochore mis-attachment and chromosome mis-segregation in cancer cells.

    Directory of Open Access Journals (Sweden)

    William T Silkworth

    Full Text Available Many cancer cells display a CIN (Chromosome Instability phenotype, by which they exhibit high rates of chromosome loss or gain at each cell cycle. Over the years, a number of different mechanisms, including mitotic spindle multipolarity, cytokinesis failure, and merotelic kinetochore orientation, have been proposed as causes of CIN. However, a comprehensive theory of how CIN is perpetuated is still lacking. We used CIN colorectal cancer cells as a model system to investigate the possible cellular mechanism(s underlying CIN. We found that CIN cells frequently assembled multipolar spindles in early mitosis. However, multipolar anaphase cells were very rare, and live-cell experiments showed that almost all CIN cells divided in a bipolar fashion. Moreover, fixed-cell analysis showed high frequencies of merotelically attached lagging chromosomes in bipolar anaphase CIN cells, and higher frequencies of merotelic attachments in multipolar vs. bipolar prometaphases. Finally, we found that multipolar CIN prometaphases typically possessed gamma-tubulin at all spindle poles, and that a significant fraction of bipolar metaphase/early anaphase CIN cells possessed more than one centrosome at a single spindle pole. Taken together, our data suggest a model by which merotelic kinetochore attachments can easily be established in multipolar prometaphases. Most of these multipolar prometaphase cells would then bi-polarize before anaphase onset, and the residual merotelic attachments would produce chromosome mis-segregation due to anaphase lagging chromosomes. We propose this spindle pole coalescence mechanism as a major contributor to chromosome instability in cancer cells.

  17. Facing evil: theological reflections

    Directory of Open Access Journals (Sweden)

    Gerrit Brand

    2011-09-01

    Full Text Available This article suggests some possible responses, drawn from the Judeo-Christian-
    Islamic tradition, to Theo de Wit’s analysis of evil, narrativity and reconciliation. It
    is argued, first, that the problem of evil is rightly seen, not as a question relating
    incidentally to faith, but as an existential challenge arising from the human condition,
    to which the Judeo-Christian-Islamic tradition has sought, from its inception, to
    provide answers. Secondly, that the theme of not downplaying evil, but facing it in its
    full reality, is central to this tradition, inter alia in the longing for, and expectation of,
    the resurrection of the dead as a way of approaching the unresolved problem of past
    evil. Some related theological concepts and questions are also brought to bear on the
    questions raised by De Wit.

  18. Facing the Challenges

    DEFF Research Database (Denmark)

    He, Kai

    2014-01-01

    China's rise signifies a gradual transformation of the international system from unipolarity to a non-unipolar world. ,4s an organization of small and middle powers, ASEAN faces strategic uncertainties brought about by the power transition in the system. Deepening economic interdependence between...... ASEAN and China has amplified the economic cost for the ASEAN states to use traditional military means to deal with China s rise. Applying institutional balancing theory, this paper examines how ASEAN has adopted various institutional instruments, such as the ASEAN Regional Forum (ARF), the East Asia...... Summit (EAS), the Regional Comprehensive Economic Partnership (RCEP), and the ASEAN Community, to constrain and shape China's behaviour in the region in the post-Cold War era. It argues that due to globalization and economic interdependence, the power transition in the 21st century is different from...

  19. Face Attention Network: An Effective Face Detector for the Occluded Faces

    OpenAIRE

    Wang, Jianfeng; Yuan, Ye; Yu, Gang

    2017-01-01

    The performance of face detection has been largely improved with the development of convolutional neural network. However, the occlusion issue due to mask and sunglasses, is still a challenging problem. The improvement on the recall of these occluded cases usually brings the risk of high false positives. In this paper, we present a novel face detector called Face Attention Network (FAN), which can significantly improve the recall of the face detection problem in the occluded case without comp...

  20. Crack growth during poling and polarisation reversal in commercial piezoceramics

    Directory of Open Access Journals (Sweden)

    Algueró, M.

    1999-12-01

    Full Text Available The growth of Vicker´s cracks during the poling of piezoelectric ceramics was studied for two PZT based compositions with different tetragonal distortion of the perovskite structure. Studies on the two compositions with different poling electric fields and similar initial crack lengths showed that crack growth was not proportional to the induced stress free longitudinal strain by 90º domain reorientation. This observation is not consistent with the previously proposed mechanism of crack growth based on a strain mismatch between the material at the crack flanks and the rest of the ceramic. This mismatch was proposed to occur because of the reduction of the electric field within the crack flanks. The reasons for the disappearance of the mismatch are discussed here, and an alternative mechanism of crack growth consistent with our results is proposed, which takes into account the electrically induced stress gradient at the crack tip, produced by the piezoelectric effect. Cracks were also found to grow during a small number of subsequent polarisation reversals, the explanation of which must be due to some other additional effect.

    Se ha estudiado el crecimiento de grietas Vicker durante la polarización de cerámicas piezoeléctricas para dos modificaciones del PZT con distinta distorsión tetragonal de la estructura perovskita. Los resultados en función del campo eléctrico de polarización y la longitud inicial de la grieta muestran que el crecimiento no es proporcional a la deformación libre de tensión inducida por orientación de dominios de 90º. Esta observación no es consistente con el mecanismo de crecimiento de grieta propuesto anteriormente, basado en el desajuste de deformación entre el material a los flancos de la grieta y el resto de la cerámica. Este desajuste se producía por la atenuación del campo eléctrico en los flancos de la grieta. Se discute la causa de la desaparición de este desajuste de deformación, y se

  1. Periods, poles, and shapes of Saturn's irregular moons

    Science.gov (United States)

    Denk, Tilmann; Mottola, Stefano

    2016-10-01

    We report rotational-lightcurve observations of irregular moons of Saturn based on disk-integrated observations with the Narrow-Angle Camera of the Cassini spacecraft. From 24 measured rotation periods, 20 are now known with an accuracy of ~2% or better. The numbers are as follows (in hours; an '*' marks the less reliable periods): Hati 5.42; Mundilfari 6.74; Loge 6.94*; Skoll 7.26; Kari 7.70; Suttungr 7.82*, Bergelmir 8.13; Phoebe 9.274; Siarnaq 10.188; Narvi 10.21; Tarvos 10.69; Skathi 11.30; Ymir 11.922; Hyrrokkin 12.76; Greip 12.79*; Ijiraq 13.03; Albiorix 13.32; Bestla 14.624; Bebhionn 16.40; Paaliaq 18.75; Kiviuq 21.96; Erriapus 28.15; Thrymr 35 or >45* Tarqeq 76.8.More recent data strengthen the notion that objects in orbits with an inclination supplemental angle i' > 27° have significantly slower spin rates than those at i' 27°, Siarnaq, stands opposed to at least eight objects with faster spins and i' 27° bin contains all nine known prograde moons and four retrograde objects.A total of 25 out of 38 known outer moons has been observed with Cassini, and there is no chance to observe the 13 missing objects until end-of-mission. However, all unobserved objects are part of the i' 27° are known, and none of them is a fast rotator, with no exception.Several objects were observed repeatedly to determine pole directions, sidereal periods, and convex shapes. A few lightcurves have been observed to show three maxima and three minima even at low phase angles, suggesting objects with a triangular equatorial cross-section. Some objects with 2 maxima/ 2 minima are probably quite elongated. One moon even shows lightcurves with 4 maxima/ 4 minima.

  2. Cytoarchitecture, probability maps and functions of the human frontal pole.

    Science.gov (United States)

    Bludau, S; Eickhoff, S B; Mohlberg, H; Caspers, S; Laird, A R; Fox, P T; Schleicher, A; Zilles, K; Amunts, K

    2014-06-01

    The frontal pole has more expanded than any other part in the human brain as compared to our ancestors. It plays an important role for specifically human behavior and cognitive abilities, e.g. action selection (Kovach et al., 2012). Evidence about divergent functions of its medial and lateral part has been provided, both in the healthy brain and in psychiatric disorders. The anatomical correlates of such functional segregation, however, are still unknown due to a lack of stereotaxic, microstructural maps obtained in a representative sample of brains. Here we show that the human frontopolar cortex consists of two cytoarchitectonically and functionally distinct areas: lateral frontopolar area 1 (Fp1) and medial frontopolar area 2 (Fp2). Based on observer-independent mapping in serial, cell-body stained sections of 10 brains, three-dimensional, probabilistic maps of areas Fp1 and Fp2 were created. They show, for each position of the reference space, the probability with which each area was found in a particular voxel. Applying these maps as seed regions for a meta-analysis revealed that Fp1 and Fp2 differentially contribute to functional networks: Fp1 was involved in cognition, working memory and perception, whereas Fp2 was part of brain networks underlying affective processing and social cognition. The present study thus disclosed cortical correlates of a functional segregation of the human frontopolar cortex. The probabilistic maps provide a sound anatomical basis for interpreting neuroimaging data in the living human brain, and open new perspectives for analyzing structure-function relationships in the prefrontal cortex. The new data will also serve as a starting point for further comparative studies between human and non-human primate brains. This allows finding similarities and differences in the organizational principles of the frontal lobe during evolution as neurobiological basis for our behavior and cognitive abilities. Copyright © 2013 Elsevier Inc. All

  3. Energy conservation using face detection

    Science.gov (United States)

    Deotale, Nilesh T.; Kalbande, Dhananjay R.; Mishra, Akassh A.

    2011-10-01

    Computerized Face Detection, is concerned with the difficult task of converting a video signal of a person to written text. It has several applications like face recognition, simultaneous multiple face processing, biometrics, security, video surveillance, human computer interface, image database management, digital cameras use face detection for autofocus, selecting regions of interest in photo slideshows that use a pan-and-scale and The Present Paper deals with energy conservation using face detection. Automating the process to a computer requires the use of various image processing techniques. There are various methods that can be used for Face Detection such as Contour tracking methods, Template matching, Controlled background, Model based, Motion based and color based. Basically, the video of the subject are converted into images are further selected manually for processing. However, several factors like poor illumination, movement of face, viewpoint-dependent Physical appearance, Acquisition geometry, Imaging conditions, Compression artifacts makes Face detection difficult. This paper reports an algorithm for conservation of energy using face detection for various devices. The present paper suggests Energy Conservation can be done by Detecting the Face and reducing the brightness of complete image and then adjusting the brightness of the particular area of an image where the face is located using histogram equalization.

  4. Cassini Returns to Saturn's Poles: Seasonal Change in the Polar Vortices

    Science.gov (United States)

    Fletcher, Leigh N.; Orton, G. S.; Irwin, P. G. J.; Sinclair, J. A.; Hesman, B. E.; Hurley, J.; Bjoraker, G. L.; Simon-Miller, A. A.

    2013-01-01

    High inclination orbits during Cassini's solstice mission (2012) are providing us with our first observations of Saturn's high latitudes since the prime mission (2007). Since that time, the northern spring pole has emerged into sunlight and the southern autumn pole has disappeared into winter darkness, allowing us to study the seasonal changes occurring within the polar vortices in response to these dramatic insolation changes. Observations from the Cassini Composite Infrared Spectrometer] have revealed (i) the continued presence of small, cyclonic polar hotspots at both spring and autumn poles; and (ii) the emergence of an infrared-bright polar vortex at the north pole, consistent with the historical record of Saturn observations from the 1980s (previous northern spring).

  5. Detection of Street Light Poles in Road Scenes from Mobile LIDAR Mapping Data for its Applications

    Science.gov (United States)

    Talebi Nahr, S.; Saadatseresht, M.; Talebi, J.

    2017-09-01

    Identification of street light poles is very significant and crucial for intelligent transportation systems. Automatic detection and extraction of street light poles are a challenging task in road scenes. This is mainly because of complex road scenes. Nowadays mobile laser scanners have been used to acquire three-dimensional geospatial data of roadways over a large area at a normal driving speed. With respect to the high density of such data, new and beneficial algorithms are needed to extract objects from these data. In this article, our proposed algorithm for extraction of street light poles consists of five main steps: 1. Preprocessing, 2. Ground removal, 3. 3D connected components analysis, 4. Local geometric feature generation, 5. Extraction of street light poles using Bhattacharya distance metric. The proposed algorithm is tested on two rural roadways, called Area1 and Area2. Evaluation results for Area1 report 0.80, 0.72 and 0.62 for completeness, correctness and quality, respectively.

  6. On PID Controller Design by Combining Pole Placement Technique with Symmetrical Optimum Criterion

    Directory of Open Access Journals (Sweden)

    Viorel Nicolau

    2013-01-01

    Full Text Available In this paper, aspects of analytical design of PID controllers are studied, by combining pole placement technique with symmetrical optimum criterion. The proposed method is based on low-order plant model with pure integrator, and it can be used for both fast and slow processes. Starting from the desired closed-loop transfer function, which contains a second-order oscillating system and a lead-lag compensator, it is shown that the zero value depends on the real-pole value of closed-loop transfer function. In addition, there is only one pole value, which satisfies the assumptions of symmetrical optimum criterion imposed to open-loop transfer function. In these conditions, by combining the pole placement technique with symmetrical optimum criterion, the analytical expressions of the controller parameters can be simplified. For simulations, PID autopilot design for heading control problem of a conventional ship is considered.

  7. Major Ion Concentrations in 2004 South Pole Ice Core, Version 1

    Data.gov (United States)

    National Aeronautics and Space Administration — A 180 m ice core drilled at South Pole in 2004/2005 was analyzed for concentrations of major ions at a depth resolution of approximately 2 cm. Measured ions are...

  8. Sulfate-Based Volcanic Record from South Pole Ice Core, Version 1

    Data.gov (United States)

    National Aeronautics and Space Administration — This data set contains concentrations of soluble chemical species (ions) within a 120 m ice core retrieved at the South Pole station in 2001. The ice core was dated...

  9. Repair of impact damaged utility poles with fiber reinforced polymers (FRP), phase II.

    Science.gov (United States)

    2015-06-01

    Vehicle collisions with steel or aluminum utility poles are common occurrences that yield substantial but often repairable : damage. This project investigates the use of a fiber-reinforced polymer (FRP) composite system for in situ repair that : mini...

  10. Subtotal splenectomy preserving the inferior splenic pole for the treatment of Hodgkin’s lymphoma

    Directory of Open Access Journals (Sweden)

    Andy Petroianu

    2017-01-01

    Conclusion: Subtotal splenectomy is efficacious to preserve the splenic functions and to prevent adverse effects of a large spleen on the treatment of Hodgkin’s lymphoma confined to superior pole and producing significant abdominal symptoms and hematological effects.

  11. Smarandache Curves In Terms of Sabban Frame of Fixed Pole Curve

    Directory of Open Access Journals (Sweden)

    Süleyman Şenyurt

    2016-06-01

    Full Text Available In this paper, we study the special Smarandache curve interms of Sabban frame of Fixed Pole curve and we give some characterization of Smarandache curves. Besides, we illustrate examples of our results.

  12. Video-based face recognition via convolutional neural networks

    Science.gov (United States)

    Bao, Tianlong; Ding, Chunhui; Karmoshi, Saleem; Zhu, Ming

    2017-06-01

    Face recognition has been widely studied recently while video-based face recognition still remains a challenging task because of the low quality and large intra-class variation of video captured face images. In this paper, we focus on two scenarios of video-based face recognition: 1)Still-to-Video(S2V) face recognition, i.e., querying a still face image against a gallery of video sequences; 2)Video-to-Still(V2S) face recognition, in contrast to S2V scenario. A novel method was proposed in this paper to transfer still and video face images to an Euclidean space by a carefully designed convolutional neural network, then Euclidean metrics are used to measure the distance between still and video images. Identities of still and video images that group as pairs are used as supervision. In the training stage, a joint loss function that measures the Euclidean distance between the predicted features of training pairs and expanding vectors of still images is optimized to minimize the intra-class variation while the inter-class variation is guaranteed due to the large margin of still images. Transferred features are finally learned via the designed convolutional neural network. Experiments are performed on COX face dataset. Experimental results show that our method achieves reliable performance compared with other state-of-the-art methods.

  13. Biomechanical characteristics and speed adaptation during kick double poling on roller skis in elite cross-country skiers.

    Science.gov (United States)

    Göpfert, Caroline; Holmberg, Hans-Christer; Stöggl, Thomas; Müller, Erich; Lindinger, Stefan Josef

    2013-06-01

    Recent developments in cross-country ski racing should promote the use of kick double poling. This technique, however, has not been the focus in athletes' training and has barely been investigated. The aims of the present study were to develop a function-based phase definition and to analyse speed adaptation mechanisms for kick double poling in elite cross-country skiers. Joint kinematics and pole/plantar forces were recorded in 10 athletes while performing kick double poling at three submaximal roller skiing speeds. A speed increase was associated with increases in cycle length and rate, while absolute poling and leg push-off durations shortened. Despite maintained impulses of force, the peak and average pole/leg forces increased. During double poling and leg push-off, ranges of motion of elbow flexion and extension increased (p aspects for technique training.

  14. The construction FACE database - Codifying the NIOSH FACE reports.

    Science.gov (United States)

    Dong, Xiuwen Sue; Largay, Julie A; Wang, Xuanwen; Cain, Chris Trahan; Romano, Nancy

    2017-09-01

    The National Institute for Occupational Safety and Health (NIOSH) has published reports detailing the results of investigations on selected work-related fatalities through the Fatality Assessment and Control Evaluation (FACE) program since 1982. Information from construction-related FACE reports was coded into the Construction FACE Database (CFD). Use of the CFD was illustrated by analyzing major CFD variables. A total of 768 construction fatalities were included in the CFD. Information on decedents, safety training, use of PPE, and FACE recommendations were coded. Analysis shows that one in five decedents in the CFD died within the first two months on the job; 75% and 43% of reports recommended having safety training or installing protection equipment, respectively. Comprehensive research using FACE reports may improve understanding of work-related fatalities and provide much-needed information on injury prevention. The CFD allows researchers to analyze the FACE reports quantitatively and efficiently. Copyright © 2017 Elsevier Ltd and National Safety Council. All rights reserved.

  15. Characteristics of Hybrid Type Switched Reluctance Motor with Salient Pole Stator

    Science.gov (United States)

    Oyama, Jun; Higuchi, Tsuyoshi; Abe, Takashi; Koga, Takahiro

    In this paper, we propose a new Hybrid type SRM with salient pole stator, which has a pair of permanent magnets attached symmetrically between the iron poles of the rotor. The paper describes experimental results of not only basic characteristics of the Hybrid SRM but also characteristics with current control loop under optimized advanced firing angle and cut-off angle. Considerable improvement of machine performance, especially efficiency and power factor, in the Hybrid SRM over conventional VR type SRM is confirmed.

  16. STS-47 MS Jemison extends side hatch mockup CES pole during JSC training

    Science.gov (United States)

    1992-01-01

    STS-47 Endeavour, Orbiter Vehicle (OV) 105, Mission Specialist (MS) Mae C. Jemison extends crew escape system (CES) pole through a side hatch mockup during launch emergency egress (bailout) training in JSC's Mockup and Integration Laboratory (MAIL) Bldg 9A. MS Jerome Apt (right) looks on. The crewmembers practiced extending the CES pole prior to donning their launch and entry suits (LESs) and conducting the simulation in the Crew Compartment Trainer (CCT).

  17. Lowering the pump power requirement for squeezed light generation using a periodically poled crystal

    DEFF Research Database (Denmark)

    Andersen, Ulrik Lund; Buchhave, Preben

    2003-01-01

    Observations of continuous wave bright squeezed light from an intra-cavity periodically poled KTP second harmonic generator are presented. The experiment includes characterization of the classical as well as the quantum properties of the system.......Observations of continuous wave bright squeezed light from an intra-cavity periodically poled KTP second harmonic generator are presented. The experiment includes characterization of the classical as well as the quantum properties of the system....

  18. Batwing versus Wise pattern mammoplasty for upper pole breast tumours: a detailed comparison of cosmetic outcome

    OpenAIRE

    Hashem, Tarek; Farahat, Ahmed

    2017-01-01

    Background The aim of this study is to compare the results of batwing mammoplasty and Wise pattern mammoplasty in the surgical management of upper pole breast tumours. Methods This is a retrospective observational study including 126 breast cancer patients who presented between 2009 and 2015 to the National Cancer Institute of Cairo University in Egypt. All patients were candidates for breast conservation, with upper pole tumours, which was defined as tumours between 3 and 9 o?clock. Patients...

  19. Preliminary Analyses of Transmedia Adaptations of Pictorial Narratives and Aesthetic Pole Interpretations: Reflections on Theory

    Directory of Open Access Journals (Sweden)

    Yu-Chai Lai

    2015-10-01

    Full Text Available Transmedia narratives are a key topic of communication research. Transmedia adaptations occur when a narrator transposes an original work by using various media platforms. Considering pictorial turn, this study employed the intermediality of an animated work that was adapted from an award-winning picture book as an example to propose an analysis for theory building. After examining the literature on transmedia narratives, intermediality, and aesthetic communication, this study proposed analyses for the dimensions of transmedia adaptations of pictorial narratives and aesthetic pole interpretations. Focusing on the three layers of the artistic pole, aesthetic pole, and interactions and effects, this study cited the cases of award-winning picture books and adapted animated works as the basis for reflecting on aesthetic communication. The artistic pole of transmedia adaptation was used as an example of how a narrator employs intermediality by citing the pictures, plot, or art forms from an original work to reinvent structures and then adapts them according to intermediality. If the aesthetic pole views the adapted animated work after reading the picture book or forms an expectation of the adaptation because of intermediality, then when the audience watches the adapted animated work, their imagination could be stimulated by the intermediality (i.e., picture book graphics and scene depictions. For transmedia narrative interaction, the aesthetic pole must “fill blanks” or “negate” to continue to view the adaptation. For filling blanks, because of intermediality, the aesthetic pole must construct an “intracompositional intermediality” to connect with the visual and audio links of the same work or construct “extracompositional intermedialtiy” to associate the original work with the transmedia adaptation. For negation, when viewing the adaptation (i.e., presentation of picture book graphics, added music, or theme song, the aesthetic pole

  20. CABLE MECHANISMS USED FOR ACTUATING CAR ELEVATORS WITH 2 AND 4 POLES

    Directory of Open Access Journals (Sweden)

    Dan MESARICI

    2015-05-01

    Full Text Available This paper presents the kinematic scheme and the operating mode of the cable mechanism used for car elevators with 2 and 4 poles. In order to increase the efficiency of the 4- pole elevator, we suggest using a new hoists type cable mechanism, which can multiply the piston travel inside the actuating cylinder twice at the platform level, when lifting and lowering.

  1. Weight-loss medicines

    Science.gov (United States)

    Prescription weight loss drugs; Diabetes - weight loss drugs; Obesity - weight loss drugs; Overweight - weight loss drugs ... Several weight-loss medicines are available. About 5 to 10 pounds (2 to 4.5 kilograms) can be lost by ...

  2. Face au risque

    CERN Document Server

    Grosse, Christian; November, Valérie

    2007-01-01

    Ce volume collectif sur le risque inaugure la collection L'ÉQUINOXE. Ancré dans l'histoire pour mesurer les continuités et les ruptures, il illustre la manière dont les sciences humaines évaluent et mesurent les enjeux collectifs du risque sur les plans politiques, scientifiques, énergétiques, juridiques et éthiques. Puisse-t-il nourrir la réflexion sur la culture et la prévention du risque. Ses formes épidémiques, écologiques, sociales, terroristes et militaires nourrissent les peurs actuelles, structurent les projets sécuritaires et constituent - sans doute - les défis majeurs à notre modernité. Dans la foulée de la richesse scientifique d'Equinoxe, L'ÉQUINOXE hérite de son esprit en prenant à son tour le pari de contribuer - non sans risque - à enrichir en Suisse romande et ailleurs le champ éditorial des sciences humaines dont notre société a besoin pour forger ses repères. Après Face au risque suivra cet automne Du sens des Lumières. (MICHEL PORRET Professeur Ordinaire à la F...

  3. Many Faces of Migrations

    Directory of Open Access Journals (Sweden)

    Milica Antić Gaber

    2013-12-01

    We believe that in the present thematic issue we have succeeded in capturing an important part of the modern European research dynamic in the field of migration. In addition to well-known scholars in this field several young authors at the beginning their research careers have been shortlisted for the publication. We are glad of their success as it bodes a vibrancy of this research area in the future. At the same time, we were pleased to receive responses to the invitation from representatives of so many disciplines, and that the number of papers received significantly exceeded the maximum volume of the journal. Recognising and understanding of the many faces of migration are important steps towards the comprehensive knowledge needed to successfully meet the challenges of migration issues today and even more so in the future. It is therefore of utmost importance that researchers find ways of transferring their academic knowledge into practice – to all levels of education, the media, the wider public and, of course, the decision makers in local, national and international institutions. The call also applies to all authors in this issue of the journal.

  4. NET plasma facing components

    International Nuclear Information System (INIS)

    Veieder, G.; Harrison, M.; Moons, F.

    1989-01-01

    The progress in the design and development of the first wall (FW) and divertor plates (DP) for the Next European Torus (NET) are summarized, highlighting the assumed main operating conditions, material choices, design options and their analysis as well as associated manufacturing studies and the ongoing testing programme. As plasma facing armor on both FW and DP, carbon based materials will be used at least during the initial physics phase due to their good performance in current tokamaks in respect to impurity control and disruption resistance. For the FW structure in water cooled austenitic steel, with radiation cooled armor adequate thermo-mechanical performance is predicted allowing peak heat fluxes of up to 0.8 MW/m 2 at 2 x 10 4 long duration burn pulses. For divertor concepts with the armor attached by brazing to a water cooled heatsink, the peak heat flux is about 10 MW/m 2 . However, the main critical issue for the DP is the lifetime which is critically limited by erosion. The demonstration of the basic feasibility of FW and DP design is in progress via manufacture and thermo-mechanical testing of prototypical mock-ups. (author). 26 refs.; 13 figs.; 2 tabs

  5. NET plasma facing components

    International Nuclear Information System (INIS)

    Vieider, G.; Harrison, M.; Moons, F.

    1989-01-01

    The progress in the design and development of the first wall (FW) and divertor plates (DP) for the Next European Torus (NET) are summarized, highlighting the assumed main operating conditions, material choices, design options and their analysis as well as associated manufacturing studies and the ongoing testing programme. As plasma facing armor on both FW and DP, carbon based materials will be used at least during the initial physics phase due to their good performance in current tokamaks in respect to impurity control and disruption resistance. For the FW structure in water cooled austenitic steel, with radiation cooled armor adequate thermo-mechanical performance is predicted allowing peak heat fluxes of up to 0.8 MW/m 2 at 2x10 4 long duration burn pulses. For divertor concepts with the armor attached by brazing to a water cooled heatsink, the peak heat flux is about 10 MW/m 2 . However, the main critical issue for the DP is the lifetime which is critically limited by erosion. The demonstation of the basic feasibility of FW and DP design is in progress via manufacture and thermo-mechanical testing of prototypical mock-ups. (orig.)

  6. Endoscopic extradural supraorbital approach to the temporal pole and adjacent area: technical note.

    Science.gov (United States)

    Komatsu, Fuminari; Imai, Masaaki; Shigematsu, Hideaki; Aoki, Rie; Oda, Shinri; Shimoda, Masami; Matsumae, Mitsunori

    2017-08-25

    The authors' initial experience with the endoscopic extradural supraorbital approach to the temporal pole and adjacent area is reported. Fully endoscopic surgery using the extradural space via a supraorbital keyhole was performed for tumors in or around the temporal pole, including temporal pole cavernous angioma, sphenoid ridge meningioma, and cavernous sinus pituitary adenoma, mainly using 4-mm, 0° and 30° endoscopes and single-shaft instruments. After making a supraorbital keyhole, a 4-mm, 30° endoscope was advanced into the extradural space of the anterior cranial fossa during lifting of the dura mater. Following identification of the sphenoid ridge, orbital roof, and anterior clinoid process, the bone lateral to the orbital roof was drilled off until the dura mater of the anterior aspect of the temporal lobe was exposed. The dura mater of the temporal lobe was incised and opened, exposing the temporal pole under a 4-mm, 0° endoscope. Tumors in or around the temporal pole were safely removed under a superb view through the extradural corridor. The endoscopic extradural supraorbital approach was technically feasible and safe. The anterior trajectory to the temporal pole using the extradural space under endoscopy provided excellent visibility, allowing minimally invasive surgery. Further surgical experience and development of specialized instruments would promote this approach as an alternative surgical option.

  7. Regge-pole description of potential scattering by means of the phase-integral method

    International Nuclear Information System (INIS)

    Amaha, A.

    1992-01-01

    The application of Regge-pole theory to different atomic and molecular scattering has shown to have promising interpretational power in the differential cross sections. Differential cross sections can be analysed in terms of interference between the 'background' amplitude and a few Regge-pole positions of the scattering matrix (S matrix) representing surface waves around the interaction region. By the analytic continuation of the radial Schroedinger differential equation into the complex plane of angular momentum one can determine the analytic properties of the S matrix which contains the physical information in the scattering processes. For interaction potentials fulfilling certain properties, the study of the S matrix leads to the study of the F matrix introduced by Froeman and Froeman for the treatment of connection problems for phase-integral solutions of the differential equation. In this thesis the quantum mechanical scattering problem is analysed in the framework of Regge-pole theory with the use of the complex-angular-momentum formalism. To determine the S matrix, the relevant F matrix elements which give the stokes constants are derived and their properties are studied. The poles of the S matrix for particular complex values of the angular momentum quantum number are the Regge-poles. Using the Regge-pole positions and residues together with the background integral, the differential cross sections are calculated and compared with corresponding partial-wave representations

  8. Pole-Shaped Object Detection Using Mobile LIDAR Data in Rural Road Environments

    Science.gov (United States)

    Yadav, M.; Husain, A.; Singh, A. K.; Lohani, B.

    2015-08-01

    Pole-shaped objects (PSOs) located along a road play key role in road safety and planning. Automation is required for calculating the numbers of trees need to be removed and utility poles need to be relocated during rural road widening. Road-side poles are among the most frequently struck road-side objects during road-side accidents. An automatic method is therefore proposed for detecting PSOs using LiDAR point cloud captured along the roadway using Mobile LiDAR system. The proposed method is tested on the point cloud data of rural road environment in India. Dataset of study area having text file size of 1.22 GB is processed in 13 minutes resulting in completeness of 88.63 % and correctness of 95.12 % in identifying PSOs within 10m of the road boundary. In data of across road coverage of 5m of the road boundary, the completeness of 93.10 % and correctness of 100% are achieved. Poles attached with other objects, tilted poles and the poles occluded by tree branches and shrubs are detected by the proposed method.

  9. Posterior Pole Sparing Laser Photocoagulation Combined with Intravitreal Bevacizumab Injection in Posterior Retinopathy of Prematurity

    Directory of Open Access Journals (Sweden)

    Rebecca Kim

    2014-01-01

    Full Text Available Purpose. To report the results of the posterior pole sparing laser photocoagulation combined with intravitreal bevacizumab injection (IVB in retinopathy of prematurity (ROP. Methods. A retrospective chart review of premature babies with ROP, all of whom received laser photocoagulation with IVB. Eleven eyes of 6 infants with advanced zone I ROP underwent laser ablation sparing posterior pole with concurrent IVB. The results were compared with those of full-laser treatment combined with IVB to 8 eyes of 5 infants with advanced ROP without involvement of the posterior pole. Results. The posterior pole sparing laser with IVB was performed with zone I, stage 3+ ROP at the mean postmenstrual age of 36 weeks and 5 days. The plus sign decreased significantly at postoperative day 1, the neovascular proliferation regressed by postoperative week 1, and the normal vascularization started at postoperative day 32 on the average. Two months after treatment, vascularization of the spared avascular area was completed. There was no macular dragging, tractional retinal detachment, foveal destruction by laser scars, or any other adverse event. No significant anatomical differences were identified from those of full-laser ablation combined with IVB. Conclusions. Posterior pole sparing laser with IVB can give favorable results without destruction of posterior pole retina.

  10. Learning to Discriminate Face Views

    Directory of Open Access Journals (Sweden)

    Fang Fang

    2011-05-01

    Full Text Available Although visual feature leaning has been well studied, we still know little about the mechanisms of perceptual learning of complex object. Here, human perceptual learning in discrimination of in-depth orientation of face view was studied using psychophysics, EEG and fMRI. We trained subjects to discriminate face orientations around a face view (i.e. 30° over eight daily sessions, which resulted in a significant improvement in sensitivity to the face view orientation. This improved sensitivity was highly specific to the trained orientation and persisted up to six months. Different from perceptual learning of simple visual features, this orientation-specific learning effect could completely transfer across changes in face size, visual field and face identity. A complete transfer also occurred between two partial face images that were mutually exclusive but constituted a complete face. However, the transfer of the learning effect between upright and inverted faces and between a face and a paperclip object was very weak. Before and after training, we measured EEG and fMRI BOLD signals responding to both the trained and the untrained face views. Analyses of ERPs and induced gamma activity showed that face view discrimination training led to a larger reduction of N170 latency at the left occipital-temporal area and a concurrent larger decrease of induced gamma activity at the left frontal area with the trained face view, compared with the untrained ones. BOLD signal amplitude and MVPA analyses showed that, in face-selective cortical areas, training did not lead to a significant amplitude change, but induced a more reliable spatial pattern of neural activity in the left FFA. These results suggest that the visual system had learned how to compute face orientation from face configural information more accurately and that a large amount of plastic changes took place at a level of higher visual processing where size-, location-, and identity

  11. Analysis of the growth poles in esthetic dentistry

    Directory of Open Access Journals (Sweden)

    Andreea Dana Tudose

    2015-05-01

    Full Text Available Growth poles are considered dynamic elements of economic growth, responsible for economical technogical, ideological, spiritual and moral integration.Bioeconomy is currently an area of great and mighty power development. High complexity of this field is to combine the use of technologies that use biological resources in the range of human values involved. This study requires that objective SWOT analysis applied in dental esthetics with strict reference to the quality of work in relation to aesthetic and functional effectiveness of the treatment, the life, the method of reconstruction, working technique, the degree of invasiveness of treatment in relation to conservation dental tissues ,execution costs, costs of resources used in dental anterior segment reconstruction and economic analysis of the modalities of treatment techniques reported the need and level of understanding of patients on treatment aesthetic-functional complexity. As material and method took into account the interaction of four factors: Strenghts-Weaknesses-Opportunities -Hazards. In group “Strengths” we have included successful treatment aesthetic-functional execution moderate cost, short time working on the seat, which shows limited use of natural resources. In group “Weaknesses” I included invasiveness of biological treatment, increased during execution of the work, aesthetic-functional failure , lack of training practitioners in dental aesthetics, lack of existant cabinets to promote interest in aesthetic dental medicine. “Opportunities” referred to the minimally invasive treatment of dental tissue in existing clinical context with predictable results, as higher interest of patients for dental esthetics, raising the standard of care internationally. In group “Risks” (threats I listed: low resistance while works (weak predictability, decreasing purchasing power, changing customer preferences, increase service quality standards. In the second chapter we

  12. Face adaptation improves gender discrimination.

    Science.gov (United States)

    Yang, Hua; Shen, Jianhong; Chen, Juan; Fang, Fang

    2011-01-01

    Adaptation to a visual pattern can alter the sensitivities of neuronal populations encoding the pattern. However, the functional roles of adaptation, especially in high-level vision, are still equivocal. In the present study, we performed three experiments to investigate if face gender adaptation could affect gender discrimination. Experiments 1 and 2 revealed that adapting to a male/female face could selectively enhance discrimination for male/female faces. Experiment 3 showed that the discrimination enhancement induced by face adaptation could transfer across a substantial change in three-dimensional face viewpoint. These results provide further evidence suggesting that, similar to low-level vision, adaptation in high-level vision could calibrate the visual system to current inputs of complex shapes (i.e. face) and improve discrimination at the adapted characteristic. Copyright © 2010 Elsevier Ltd. All rights reserved.

  13. Emotion Words: Adding Face Value.

    Science.gov (United States)

    Fugate, Jennifer M B; Gendron, Maria; Nakashima, Satoshi F; Barrett, Lisa Feldman

    2017-06-12

    Despite a growing number of studies suggesting that emotion words affect perceptual judgments of emotional stimuli, little is known about how emotion words affect perceptual memory for emotional faces. In Experiments 1 and 2 we tested how emotion words (compared with control words) affected participants' abilities to select a target emotional face from among distractor faces. Participants were generally more likely to false alarm to distractor emotional faces when primed with an emotion word congruent with the face (compared with a control word). Moreover, participants showed both decreased sensitivity (d') to discriminate between target and distractor faces, as well as altered response biases (c; more likely to answer "yes") when primed with an emotion word (compared with a control word). In Experiment 3 we showed that emotion words had more of an effect on perceptual memory judgments when the structural information in the target face was limited, as well as when participants were only able to categorize the face with a partially congruent emotion word. The overall results are consistent with the idea that emotion words affect the encoding of emotional faces in perceptual memory. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

  14. The Kent Face Matching Test.

    Science.gov (United States)

    Fysh, Matthew C; Bindemann, Markus

    2018-05-01

    This study presents the Kent Face Matching Test (KFMT), which comprises 200 same-identity and 20 different-identity pairs of unfamiliar faces. Each face pair consists of a photograph from a student ID card and a high-quality portrait that was taken at least three months later. The test is designed to complement existing resources for face-matching research, by providing a more ecologically valid stimulus set that captures the natural variability that can arise in a person's appearance over time. Two experiments are presented to demonstrate that the KFMT provides a challenging measure of face matching but correlates with established tests. Experiment 1 compares a short version of this test with the optimized Glasgow Face Matching Test (GFMT). In Experiment 2, a longer version of the KFMT, with infrequent identity mismatches, is correlated with performance on the Cambridge Face Memory Test (CFMT) and the Cambridge Face Perception Test (CFPT). The KFMT is freely available for use in face-matching research. © 2017 The British Psychological Society.

  15. Catastrophic injuries in pole vaulters: a prospective 9-year follow-up study.

    Science.gov (United States)

    Boden, Barry P; Boden, Matthew G; Peter, Rebecca G; Mueller, Fred O; Johnson, Jan E

    2012-07-01

    A prior review of catastrophic pole vaulting injuries from 1982 through 1998 revealed an average of 2.0 injuries per year, with 69% (1.38 per year) of the injuries secondary to athletes landing off the sides or back of the landing pad and 25% (0.5 per year) from athletes landing in the vault box. In 2003, several rule changes for the sport of pole vaulting were mandated, including enlarging the minimum dimensions of the landing pad. Our goals were to (1) identify the post-2003 rule change incidence and profile of catastrophic pole vaulting injuries through 2011 and compare them, where possible, with the prior incidence and profile and (2) determine, via a questionnaire, the frequency with which pole vaulters land in the vault box. We hypothesized that the new, larger landing pads would reduce the number of catastrophic injuries. Descriptive epidemiology study. We prospectively reviewed all catastrophic pole vaulting injuries (ie, brain hemorrhage; skull, spine, or pelvic fracture; substantial pulmonary or intra-abdominal injury) in the United States from 2003 through 2011, surveyed 3335 pole vaulters to determine the frequency of landing in the vault box, and compared results with those in the literature. From 2003 to 2011, 19 catastrophic injuries occurred (average of 2.1 per year), with the majority (n = 14, 74%, 1.55 per year) landing in or around the vault box. Four (21%, 0.44 per year) injuries occurred when an athlete landed off the sides or back of the landing pad and 1 (5%) when the pole broke. There were 11 (58%) major head injuries (1 fatality), 4 (21%) spine fractures (1 with paraplegia), 2 (11%) pelvic fractures (both with intra-abdominal injuries), 1 (5%) brain stem injury (fatal), and 1 (5%) thoracic injury (rib fractures and pneumothorax). The annual fatality rate fell from 1.0 in the prior study to 0.22 in the current study. According to the pole vaulters survey, during their careers, 77.12% (n = 2572) landed in the vault box 1 to 3 times, 15.92% (n

  16. Coordinating face-to-face meetings in mobile network societies

    DEFF Research Database (Denmark)

    Larsen, Jonas; Urry, John; Axhausen, Kay

    2008-01-01

    and conduct face-to-face meetings. We show striking changes in technologies and cultures of coordination - a shift from punctuality effected through clock time to a flexible and perpetual coordination effected through email and mobiles. This empirical research addresses specifically located embodied practices...

  17. Attention to internal face features in unfamiliar face matching.

    Science.gov (United States)

    Fletcher, Kingsley I; Butavicius, Marcus A; Lee, Michael D

    2008-08-01

    Accurate matching of unfamiliar faces is vital in security and forensic applications, yet previous research has suggested that humans often perform poorly when matching unfamiliar faces. Hairstyle and facial hair can strongly influence unfamiliar face matching but are potentially unreliable cues. This study investigated whether increased attention to the more stable internal face features of eyes, nose, and mouth was associated with more accurate face-matching performance. Forty-three first-year psychology students decided whether two simultaneously presented faces were of the same person or not. The faces were displayed for either 2 or 6 seconds, and had either similar or dissimilar hairstyles. The level of attention to internal features was measured by the proportion of fixation time spent on the internal face features and the sensitivity of discrimination to changes in external feature similarity. Increased attention to internal features was associated with increased discrimination in the 2-second display-time condition, but no significant relationship was found in the 6-second condition. Individual differences in eye-movements were highly stable across the experimental conditions.

  18. Sample Return Mission to the South Pole Aitken Basin

    Science.gov (United States)

    Duke, M. B.; Clark, B. C.; Gamber, T.; Lucey, P. G.; Ryder, G.; Taylor, G. J.

    1999-01-01

    The South Pole Aitken Basin (SPA) is the largest and oldest observed feature on the Moon. Compositional and topographic data from Galileo, Clementine, and Lunar Prospector have demonstrated that SPA represents a distinctive major lunar terrane, which has not been sampled either by sample return missions (Apollo, Luna) or by lunar meteorites. The floor of SPA is characterized by mafic compositions enriched in Fe, Ti, and Th in comparison to its surroundings. This composition may represent melt rocks from the SPA event, which would be mixtures of the preexisting crust and mantle rocks. However, the Fe content is higher than expected, and the large Apollo basin, within SPA, exposes deeper material with lower iron content. Some of the Fe enrichment may represent mare and cryptomare deposits. No model adequately accounts for all of the characteristics of the SPA and disagreements are fundamental. Is mantle material exposed or contained as fragments in melt rock and breccias? If impact melt is present, did the vast sheet differentiate? Was the initial mantle and crust compositionally different from other regions of the Moon? Was the impact event somehow peculiar, (e.g., a low-velocity impact)? The precise time of formation of the SPA is unknown, being limited only by the initial differentiation of the Moon and the age of the Imbrium event, believed to be 3.9 b.y. The questions raised by the SPA can be addressed only with detailed sample analysis. Analysis of the melt rocks, fragments in breccias, and basalts of SPA can address several highly significant problems for the Moon and the history of the solar system. The time of formation of SPA, based on analysis of melt rocks formed in the event. would put limits on the period of intense bombardment of the Moon, which has been inferred by some to include a "terminal cataclysm." If close to 3.9 Ga, the presumed age of the Imbrium Basin, the SPA date would confirm the lunar cataclysm. This episode, if it occurred, would have

  19. Management of displaced inferior patellar pole fractures with modified tension band technique combined with cable cerclage using Cable Grip System.

    Science.gov (United States)

    Yang, Xu; Wu, Qinfen; Lai, Chin-Hui; Wang, Xin

    2017-10-01

    We present a modified tension band technique combined with cable cerclage using Cable Grip System for the treatment of displaced inferior patellar pole fractures and report the knee functional outcome. The patients who had had operative treatment of a displaced inferior patellar pole fracture (AO/OTA 34-A1) between December 2013 and December 2015 were studied retrospectively. Eleven consecutive patients had had open reduction and internal fixation with the modified technique using Cable Grip System, of whom, five males and six females with an average age of 60.9 years (range, 29-81 years). All fractures occurred from direct fall onto the knee. The average time from injury to surgery was 6.1days (range, 2-12days). The range of motion (ROM) was measured in degrees by goniometry at postoperative intervals of 1, 2, 4, 12, and 48 weeks; Knee function was evaluated using the Rasmussen scores at final follow-up. No patients had nonunion, loss of reduction, migration of wire, irritation from the implant and fixation breakage during the follow-up period. Recovery of ROM was achieved at 12 weeks, with the average ROM at 1 week was 72° (range, 65°-78°), 86.4° (range, 78°-92°) at 2 weeks, 115.5° (range, 103°-122°) at 4 weeks, 129.6° (range, 122°-133°) at 12 weeks, 134.5° (range, 129°-139°) at 48 weeks after the operation. Concerning the knee function outcome assessment, all patients showed excellent results at final follow-up. The average Rasmussen scores was 27.9 out of 30 (range, 27-29). The modified tension band technique combined with cable cerclage using Cable Grip System for displaced inferior patellar pole fractures can provide stable fixation with excellent results in knee function, allows for immediate mobilization and early weight-bearing, which is a simple and valuable technique in routine clinical practice. Copyright © 2017 Elsevier Ltd. All rights reserved.

  20. Thermal analysis and improvement of cascode GaN device package for totem-pole bridgeless PFC rectifier

    International Nuclear Information System (INIS)

    She, Shuojie; Zhang, Wenli; Liu, Zhengyang; Lee, Fred C.; Huang, Xiucheng; Du, Weijing; Li, Qiang

    2015-01-01

    The totem-pole bridgeless power factor correction (PFC) rectifier has a simpler topology and higher efficiency than other boost-type bridgeless PFC rectifiers. Its promising performance is enabled by using high-voltage gallium nitride (GaN) high-electron-mobility transistors, which have considerably better figures of merit (e.g., lower reverse recovery charges and less switching losses) than the state-of-the-art silicon metal-oxide-semiconductor field-effect transistors. Cascode GaN devices in traditional packages, i.e., the TO-220 and power quad flat no-lead, are used in the totem-pole PFC boost rectifier. But the parasitic inductances induced by the traditional packages not only significantly deteriorate the switching characteristics of the discrete GaN device but also adversely affect the performance of the built PFC rectifier. A new stack-die packaging structure with an embedded capacitor has been introduced and proven to be efficient in reducing parasitic ringing at the turn-off transition and achieving true zero-voltage-switching turn-on. However, the thermal dissipation capability of the device packaged in this configuration becomes a limitation on further pushing the operating frequency and the output current level for high-efficiency power conversion. This paper focuses on the thermal analysis of the cascode GaN devices in different packages and the GaN-based multichip module used in a two-phase totem-pole bridgeless PFC boost rectifier. A series of thermal models are built based on the actual structures and materials of the packaged devices to evaluate their thermal performance. Finite element analysis (FEA) simulation results of the cascode GaN device in a flip-chip format demonstrate the possibility of increasing the device switching speed while maintaining the peak temperature of the device below 125 °C. Thermal analysis of the GaN-based power module in a very similar structure is also conducted using the FEA method. Experimental data measured using

  1. Finding Hope in the Face-to-Face.

    Science.gov (United States)

    Edgoose, Jennifer Y C; Edgoose, Julian M

    2017-05-01

    What does it mean to look into the face of a patient who looks back? Face-to-face encounters are at the heart of the patient-clinician relationship but their singular significance is often lost amid the demands of today's high-tech, metric-driven health care systems. Using the framework provided by the philosopher and Holocaust survivor Emmanuel Levinas, the authors explore the unique responsibility and potential for hope found only in face-to-face encounters. Revisiting this most fundamental attribute of medicine is likely our greatest chance to reclaim who we are as clinicians and why we do what we do. © 2017 Annals of Family Medicine, Inc.

  2. Facing My Fears (Editorial

    Directory of Open Access Journals (Sweden)

    Lindsay Glynn

    2008-03-01

    Full Text Available I’m scared. I’m nervous. In a few short weeks the contractors and electricians will take over my library for several months. They will drill huge gouges in the concrete floor, hammer, saw, scrape,move, wire, etc. No doubt they may have to be asked to keep their voices down once or twice. Half of the print journal collection will be relocated to accommodate a new teaching lab that will also double as an information commons. The planning has been going on for many months. We have consulted with other libraries, reviewed the literature, identified the needs of our various user groups, measured space,tested technical possibilities, and met with architects and engineers. Up until now the new lab was an organic idea on paper, discussed over coffee and in meetings. That’s fairly easy to deal with. But just around the corner it becomes a reality and I’m a bag of nerves. Have we made the right decisions? Will it address all our needs? Is there anything I forgot to consider? What if our users don’t like it? What if it is a complete failure?!Theoretically, it should be ok. I’ve followed the right steps and worked with a creative, talented and dedicated team. This is different from trying out a new instructional technique or reorganizing the information desk. This is big. I talk the evidence based talk regularly, but now I am walking the walk in a bigger way than I had ever imagined. Change can be frightening. Moving out of comfort zones is not easy. Having said that, the challenge can be invigorating and the change, refreshing. I find myself welcoming the change as much as I dread it. I’ll face my fears and see it through to the implementation and evaluations and beyond. And hey, no matter what the outcome, it should make for a good paper. If anyone else out there is going through a similar process, I’d be interested in comparing notes. I invite you to try something new this year in your work environment or in your professional activities

  3. The Association Between Dental Status and Risk of Acute Myocardial Infarction Among Poles: Case-control Study.

    Science.gov (United States)

    Górski, Bartłomiej; Nargiełło, Ewa; Grabowska, Ewa; Opolski, Grzegorz; Górska, Renata

    2016-01-01

    Results of scientific research on the effects of periodontitis on the incidence of myocardial infarction (MI) are ambiguous. The aim of this study was to investigate the association of the severity and extent of periodontitis with acute MI in Poles. This case-control study included 134 cases hospitalized with acute MI under the age of 70 years and 155 controls drawn from the general population with no MI history. Sociodemographic, cardiologic and periodontal variables were assessed. Three periodontal indicators were evaluated: (1) the severity of periodontitis classified in accordance with Page and Eke definition, (2) the extent of periodontitis determined on the basis of the percentage of sites with CAL ≥ 3 mm (Arbes Index) and (3) tooth loss (> 10 teeth). In a logistic regression model, the association of periodontal parameters with MI occurrence was evaluated after adjusting for well-known cardiovascular risk factors. The extent of periodontitis was significantly associated with the risk of acute MI even after adjusting for age, sex, tobacco smoking, hypertension, diabetes, BMI, education and income (odds ratio [OR] = 2.4; 95% confidence interval [CI] = 1.1 to 5.2; p = 0.0203). However, the severity of periodontitis was associated with MI after adjusting for age and sex (OR = 2.0; 95% CI = 1.2-3.5; p = 0.0109), but not after adjusting for the other above-mentioned risk factors. The association between the number of lost teeth and acute MI was significant after adjusting for age, sex, tobacco smoking, arterial hypertension and diabetes mellitus (OR = 2.1; 95% CI = 1.2-5.9; p = 0.0151). This study proves the positive association between periodontitis and acute MI in Poles. This association seems to be stronger with regard to the extent rather than to the severity of periodontitis.

  4. CURRENT STATUS OF THE POLE-AND-LINE FISHERY IN EASTERN PART OF INDONESIA

    Directory of Open Access Journals (Sweden)

    Agustinus Anung Widodo

    2016-12-01

    Full Text Available The promotion of pole-and-line fishery for a selective gear operating in the Indonesian tuna management area is considered as the proper policy in response to the increasing market demand with tuna eco-labeled. Appropriate information in addressing the current status of the pole-and-line fishery in Indonesia is an important step in order to support the promotion. Data used to describe the fishery were obtained through scientific port sampling program in collaboration between RCFMC and WCPFC in 2010 to 2014 and also scientific observer onboard program collaboration RCFMC and CRAC Co. Ltd. in 2013. The results show that presently the number of pole and line fleets was decreased significantly and remain about 232 fleetsin Sorong, Bitung and Kendari and Larantuka. The national annual total catch of pole-and line during 1980 – 2013 was recorded between 24,000 and 160,000 tons per year (average 98,117 tons per year. This value is estimated to contribute about 20% of Indonesia annual total catch of tuna in FMAs713-717. The pole-andline catch rates based at Bitung, Kendari and Sorong were fluctuated in each year with the range respective between 8.79 and 17.93 tons/trip/vessel, 4.78 and 5.36 ton/trip/vessel and about 7,99 ton ton/trip/vessel. Pole-and-line fishery operated in Indonesian FMAs 713-717 is considered as selective fishery, with > 80 % catches of skipjack in matured stage. The tuna-live bait fish ratio in Indonesian pole-and-line was 4.41 :1, then an improvement of live bait ratio as well as its management is required.

  5. Impaired processing of self-face recognition in anorexia nervosa.

    Science.gov (United States)

    Hirot, France; Lesage, Marine; Pedron, Lya; Meyer, Isabelle; Thomas, Pierre; Cottencin, Olivier; Guardia, Dewi

    2016-03-01

    Body image disturbances and massive weight loss are major clinical symptoms of anorexia nervosa (AN). The aim of the present study was to examine the influence of body changes and eating attitudes on self-face recognition ability in AN. Twenty-seven subjects suffering from AN and 27 control participants performed a self-face recognition task (SFRT). During the task, digital morphs between their own face and a gender-matched unfamiliar face were presented in a random sequence. Participants' self-face recognition failures, cognitive flexibility, body concern and eating habits were assessed with the Self-Face Recognition Questionnaire (SFRQ), Trail Making Test (TMT), Body Shape Questionnaire (BSQ) and Eating Disorder Inventory-2 (EDI-2), respectively. Subjects suffering from AN exhibited significantly greater difficulties than control participants in identifying their own face (p = 0.028). No significant difference was observed between the two groups for TMT (all p > 0.1, non-significant). Regarding predictors of self-face recognition skills, there was a negative correlation between SFRT and body mass index (p = 0.01) and a positive correlation between SFRQ and EDI-2 (p recognition.

  6. PrimeFaces beginner's guide

    CERN Document Server

    Reddy, K Siva Prasad

    2013-01-01

    A guide for beginner's with step-by-step instructions and an easy-to-follow approach.PrimeFaces Beginners Guide is a simple and effective guide for beginners, wanting to learn and implement PrimeFaces in their JSF-based applications. Some basic JSF and jQuery skills are required before you start working through the book.

  7. Face recognition using Krawtchouk moment

    Indian Academy of Sciences (India)

    Abstract. Feature extraction is one of the important tasks in face recognition. Moments are widely used feature extractor due to their superior discriminatory power and geometrical invariance. Moments generally capture the global features of the image. This paper proposes Krawtchouk moment for feature extraction in face ...

  8. Face recognition using Krawtchouk moment

    Indian Academy of Sciences (India)

    Artificial Intelligence 17(1): 41–62. Hu M K 1962 Visual pattern recognition by moment invariants. IRE Trans. on Information Theory, IT-8,. 179–187. Huang F T, Zhou Z, Zhang H-J and Chen T 2000 Pose invariant face recognition, Proc. Fourth IEEE. International Conference on Automatic Face and Gesture Recognition, ...

  9. Side-View Face Recognition

    NARCIS (Netherlands)

    Santemiz, P.; Spreeuwers, Lieuwe Jan; Veldhuis, Raymond N.J.; van den Biggelaar, Olivier

    As a widely used biometrics, face recognition has many advantages such as being non-intrusive, natural and passive. On the other hand, in real-life scenarios with uncontrolled environment, pose variation up to side-view positions makes face recognition a challenging work. In this paper we discuss

  10. Forensic Face Recognition: A Survey

    NARCIS (Netherlands)

    Ali, Tauseef; Veldhuis, Raymond N.J.; Spreeuwers, Lieuwe Jan

    2010-01-01

    Beside a few papers which focus on the forensic aspects of automatic face recognition, there is not much published about it in contrast to the literature on developing new techniques and methodologies for biometric face recognition. In this report, we review forensic facial identification which is

  11. Newborns' Mooney-Face Perception

    Science.gov (United States)

    Leo, Irene; Simion, Francesca

    2009-01-01

    The aim of this study is to investigate whether newborns detect a face on the basis of a Gestalt representation based on first-order relational information (i.e., the basic arrangement of face features) by using Mooney stimuli. The incomplete 2-tone Mooney stimuli were used because they preclude focusing both on the local features (i.e., the fine…

  12. Centered On The Pole: NCEI Interdisciplinary Arctic Data Stewardship

    Science.gov (United States)

    Zweng, M.

    2016-02-01

    In 2014, NOAA's data centers (National Climatic Data Center, National Oceanographic Data Center, National Geophysical Data Center and its affiliated program within the National Snow and Ice Data Center, and the National Coastal Data Development Center) merged to form NCEI, the National Centers for Environmental Information- the largest repository of publicly accessible earth system science data in the world. The merger has forced a reconciling of different workflows, data types, and cultures. However, the Arctic has emerged as a common area where the different centers can integrate their expertise, data assets, and services, and use this information to better align the entire organization. The centers face a unique challenge as they move forward: how to archive, steward and provide access to environmental data to fulfil their mission of providing the best information to help protect life and property. A pressing national need for information that supports policy decisions drives our work.

  13. Effective indexing for face recognition

    Science.gov (United States)

    Sochenkov, I.; Sochenkova, A.; Vokhmintsev, A.; Makovetskii, A.; Melnikov, A.

    2016-09-01

    Face recognition is one of the most important tasks in computer vision and pattern recognition. Face recognition is useful for security systems to provide safety. In some situations it is necessary to identify the person among many others. In this case this work presents new approach in data indexing, which provides fast retrieval in big image collections. Data indexing in this research consists of five steps. First, we detect the area containing face, second we align face, and then we detect areas containing eyes and eyebrows, nose, mouth. After that we find key points of each area using different descriptors and finally index these descriptors with help of quantization procedure. The experimental analysis of this method is performed. This paper shows that performing method has results at the level of state-of-the-art face recognition methods, but it is also gives results fast that is important for the systems that provide safety.

  14. Three-Pole Tunable Filters with High Rejection using Mixed Quarter-Lambda and Asymmetric Half-Lambda Resonators

    Directory of Open Access Journals (Sweden)

    Zhiyuan Zhao

    2014-09-01

    Full Text Available A novel three-pole tunable bandpass filter using varactor-loaded quarter-wavelength combline and asym-metric half-wavelength resonators is proposed in this paper. A nearly constant 3-dB absolute bandwidth is 150 ± 13 MHz (10.7%~6.9% fractional bandwidth within the tuning range of 1.4-2.0 GHz (42.8%. The filter is designed on a Rogers substrate with relative permittivity 2.2 and h=1 mm with its insertion loss varying from 3.6 dB to 2.8 dB and return loss better than 10 dB over the entire tuning range. The creation of two transmission zeros near the passband edges is analyzed by the even-odd-method. By using dissimilar resonators, the proposed tunable filter could obtain > 33 dB rejection levels at the second harmonics. The measured results show good agreement with the simulated ones.

  15. Face-Lift Satisfaction Using the FACE-Q.

    Science.gov (United States)

    Sinno, Sammy; Schwitzer, Jonathan; Anzai, Lavinia; Thorne, Charles H

    2015-08-01

    Face lifting is one of the most common operative procedures for facial aging and perhaps the procedure most synonymous with plastic surgery in the minds of the lay public, but no verifiable documentation of patient satisfaction exists in the literature. This study is the first to examine face-lift outcomes and patient satisfaction using a validated questionnaire. One hundred five patients undergoing a face lift performed by the senior author (C.H.T.) using a high, extended-superficial musculoaponeurotic system with submental platysma approximation technique were asked to complete anonymously the FACE-Q by e-mail. FACE-Q scores were assessed for each domain (range, 0 to 100), with higher scores indicating greater satisfaction with appearance or superior quality of life. Fifty-three patients completed the FACE-Q (50.5 percent response rate). Patients demonstrated high satisfaction with facial appearance (mean ± SD, 80.7 ± 22.3), and quality of life, including social confidence (90.4 ± 16.6), psychological well-being (92.8 ± 14.3), and early life impact (92.2 ± 16.4). Patients also reported extremely high satisfaction with their decision to undergo face lifting (90.5 ± 15.9). On average, patients felt they appeared 6.9 years younger than their actual age. Patients were most satisfied with the appearance of their nasolabial folds (86.2 ± 18.5), cheeks (86.1 ± 25.4), and lower face/jawline (86.0 ± 20.6), compared with their necks (78.1 ± 25.6) and area under the chin (67.9 ± 32.3). Patients who responded in this study were extremely satisfied with their decision to undergo face lifting and the outcomes and quality of life following the procedure.

  16. Mental rotation of faces in healthy aging and Alzheimer's disease.

    Directory of Open Access Journals (Sweden)

    Cassandra A Adduri

    Full Text Available BACKGROUND: Previous research has shown that individuals with Alzheimer's disease (AD develop visuospatial difficulties that affect their ability to mentally rotate objects. Surprisingly, the existing literature has generally ignored the impact of this mental rotation deficit on the ability of AD patients to recognize faces from different angles. Instead, the devastating loss of the ability to recognize friends and family members in AD has primarily been attributed to memory loss and agnosia in later stages of the disorder. The impact of AD on areas of the brain important for mental rotation should not be overlooked by face processing investigations -- even in early stages of the disorder. METHODOLOGY/PRINCIPAL FINDINGS: This study investigated the sensitivity of face processing in AD, young controls and older non-neurological controls to two changes of the stimuli -- a rotation in depth and an inversion. The control groups showed a systematic effect of depth rotation, with errors increasing with the angle of rotation, and with inversion. The majority of the AD group was not impaired when faces were presented upright and no transformation in depth was required, and were most accurate when all faces were presented in frontal views, but accuracy was severely impaired with any rotation or inversion. CONCLUSIONS/SIGNIFICANCE: These results suggest that with the onset of AD, mental rotation difficulties arise that affect the ability to recognize faces presented at different angles. The finding that a frontal view is "preferred" by these patients provides a valuable communication strategy for health care workers.

  17. Static Multiple-Pole Homopolar Generator With a Superconducting Screen,

    Science.gov (United States)

    1983-11-03

    nonsuperconducting "hole" in it thermal losses caused by Foucault currents develop. * The result of this is that the band does not "manage" to switch...electrica.l resistance and becomes permeable for magnetic flux). In Figures 3, 4, 5 these areas are limited by the coordinates (xl-x 2 ) and (x3-x4...In the remaining areas the screen remains "-. i , superconducting, i.e., it possesses ero resistance , and since it is made out of a superconductor of

  18. Investigation of a less rare-earth permanent-magnet machine with the consequent pole rotor

    Science.gov (United States)

    Bai, Jingang; Liu, Jiaqi; Wang, Mingqiao; Zheng, Ping; Liu, Yong; Gao, Haibo; Xiao, Lijun

    2018-05-01

    Due to the rising price of rare-earth materials, permanent-magnet (PM) machines in different applications have a trend of reducing the use of rare-earth materials. Since iron-core poles replace half of PM poles in the consequent pole (CP) rotor, the PM machine with CP rotor can be a promising candidate for less rare-earth PM machine. Additionally, the investigation of CP rotor in special electrical machines, like hybrid excitation permanent-magnet PM machine, bearingless motor, etc., has verified the application feasibility of CP rotor. Therefore, this paper focuses on design and performance of PM machines when traditional PM machine uses the CP rotor. In the CP rotor, all the PMs are of the same polarity and they are inserted into the rotor core. Since the fundamental PM flux density depends on the ratio of PM pole to iron-core pole, the combination rule between them is investigated by analytical and finite-element methods. On this basis, to comprehensively analyze and evaluate PM machine with CP rotor, four typical schemes, i.e., integer-slot machines with CP rotor and surface-mounted PM (SPM) rotor, fractional-slot machines with CP rotor and SPM rotor, are designed to investigate the performance of PM machine with CP rotor, including electromagnetic performance, anti-demagnetization capacity and cost.

  19. The effects of poling on physiological, kinematic and kinetic responses in roller ski skating.

    Science.gov (United States)

    Grasaas, Erik; Hegge, Ann Magdalen; Ettema, Gertjan; Sandbakk, Øyvind

    2014-09-01

    We investigated the effects of poling on physiological, kinematic and kinetic responses in the G4 skating technique where the poling movement is synchronized with the leg push-off on one side (strong side) followed by a forward arm swing during the leg push-off on the other side (weak side). G4 skating with (G4-P) and without (G4-NP) poling was compared in 17 elite male cross-country skiers during 4-min submaximal tests on a 2% inclined roller ski treadmill at 10, 15 and 20 km h(-1). G4-P demonstrated less ventilatory stress and higher gross efficiency compared to G4-NP at all velocities, and the blood lactate concentration was lower at the high velocity (all P ski forces, increased ski velocities and less angling and edging of the skis (all P ski forces on the strong side were lower than on the weak side with G4-P at all velocities (all P ski forces at a given work rate with G4-P demonstrate the effectiveness of poling in the G4 skating technique. Thus, poling provides possibilities to increase total propulsion, to reduce ski forces and to enhance skiing efficiency.

  20. zic-1 Expression in Planarian neoblasts after injury controls anterior pole regeneration.

    Directory of Open Access Journals (Sweden)

    Constanza Vásquez-Doorman

    2014-07-01

    Full Text Available Mechanisms that enable injury responses to prompt regenerative outgrowth are not well understood. Planarians can regenerate essentially any tissue removed by wounding, even after decapitation, due to robust regulation of adult pluripotent stem cells of the neoblast population. Formation of pole signaling centers involving Wnt inhibitors or Wnt ligands promotes head or tail regeneration, respectively, and this process requires the use of neoblasts early after injury. We used expression profiling of purified neoblasts to identify factors needed for anterior pole formation. Using this approach, we identified zic-1, a Zic-family transcription factor, as transcriptionally activated in a subpopulation of neoblasts near wound sites early in head regeneration. As head regeneration proceeds, the Wnt inhibitor notum becomes expressed in the newly forming anterior pole in zic-1-expressing cells descended from neoblasts. Inhibition of zic-1 by RNAi resulted in a failure to express notum at the anterior pole and to regenerate a head, but did not affect tail regeneration. Both injury and canonical Wnt signaling inhibition are required for zic-1 expression, and double-RNAi experiments suggest zic-1 inhibits Wnt signaling to allow head regeneration. Analysis of neoblast fate determinants revealed that zic-1 controls specification of notum-expressing cells from foxD-expressing neoblasts to form the anterior pole, which organizes subsequent outgrowth. Specialized differentiation programs may in general underlie injury-dependent formation of tissue organizing centers used for regenerative outgrowth.

  1. Cell and molecular biology of spindle poles and NuMA.

    Science.gov (United States)

    Fant, Xavier; Merdes, Andreas; Haren, Laurence

    2004-01-01

    Mitotic and meiotic cells contain a bipolar spindle apparatus of microtubules and associated proteins. To arrange microtubules into focused spindle poles, different mechanisms are used by various organisms. Principally, two major pathways have been characterized: nucleation and anchorage of microtubules at preexisting centers such as centrosomes or spindle pole bodies, or microtubule growth off the surface of chromosomes, followed by sorting and focusing into spindle poles. These two mechanisms can even be found in cells of the same organism: whereas most somatic animal cells utilize the centrosome as an organizing center for spindle microtubules, female meiotic cells build an acentriolar spindle apparatus. Most interestingly, the molecular components that drive acentriolar spindle pole formation are also present in cells containing centrosomes. They include microtubule-dependent motor proteins and a variety of structural proteins that regulate microtubule orientation, anchoring, and stability. The first of these spindle pole proteins, NuMA, had already been identified more than 20 years ago. In addition, several new proteins have been characterized more recently. This review discusses their role during spindle formation and their regulation in the cell cycle.

  2. Reanalysis of Clementine Bistatic Radar Data from the Lunar South Pole

    Science.gov (United States)

    Simpson, Richard A.; Tyler, G. Leonard

    1998-01-01

    On 9 April 1994 the Clementine spacecraft high-gain antenna was aimed toward the Moon's surface and the resulting 13-cm wavelength radio echoes were received on Earth. Using these data, we have found that the lunar surface generally follows a Lambertian bistatic scattering function sigma(sub 0) = K(sub D)cos(theta(sub i) with K(sub D) approx. 0.003 for the opposite (expected) sense of circular polarization and K(sub D) approx. 0.001 for the same (unexpected) sense. But there are important deviations-of up to 50% in some parts of the echo spectrum-from this simple form. Based on an earlier analysis of these same data, Nozette et al. claimed detection of an enhancement in echoes with right circular polarization from regions near the South Pole in a near-backscatter geometry. Such behavior would be consistent with presence of perhaps large quantities of water ice near the Pole. We have been unable to reproduce that result. Although we find weak suggestions of enhanced echoes at the time of South Pole backscatter, similar features are present at earlier and later times, adjacent frequencies, and in left circular polarization. If enhanced backscatter is present, it is not unique to the South Pole; if not unique to the Pole, then ice is less likely as an explanation for the enhancement.

  3. Novel Treatment of a Scapholunate Ligament Injury with Proximal Pole Scaphoid Nonunion

    Science.gov (United States)

    Gaspar, Michael P.; Kane, Patrick M.; Jacoby, Sidney M.; Culp, Randall W.

    2016-01-01

    Background  Nonunion of scaphoid proximal pole fractures presents a challenging management dilemma to hand surgeons. This problem is further complicated in the uncommon concurrence of scapholunate (SL) ligament disruption. Case Description  A 39-year-old male patient presented with new-onset wrist pain following a remote history of a proximal pole scaphoid fracture sustained as a teenager, which was treated nonoperatively. Six months before presentation, the patient sustained a fall while snowboarding. The patient was found to have a chronic nonunion of his scaphoid proximal pole with an associated SL ligament disruption. As the proximal fragment was too small to be amenable to fixation, the patient was treated with an arthroscopic partial scaphoid excision and SL ligament reconstruction using a scapholunateintercarpal screw placed percutaneously. At 26 months, the patient exhibited no pain, near-normal strength, and wrist motion, and expressed a high-level of satisfaction from his surgery. Literature Review  Although cases of SL ligament disruption with concomitant proximal scaphoid fractures have been reported, to our knowledge, this is the first report of SL ligament rupture occurring in the setting of a preexisting proximal pole scaphoid nonunion. Clinical Relevance  We report the use of SL ligament reconstruction augmented with intercarpal screw fixation, and excision of the proximal pole scaphoid nonunion. This minimallyinvasive approach may be a particularly useful option in young, active patients such as our own, where a motion-sacrificing salvage procedure would be less than ideal. PMID:27616829

  4. Laminated wood as an alternative to wood poles : Engineered wood structures for electric utility and telecommunications industries

    Energy Technology Data Exchange (ETDEWEB)

    Reisdorff, R. [Laminated Wood Systems Inc., Seward, NE (United States)

    2002-07-01

    In this PowerPoint presentation, the author discusses the major advantages of laminated structures, for both the electric and telecommunication industries. The advantages include economy, quick delivery, climbing and field modifications, dimensional uniformity and stability. A series of pictures was displayed which showed the manufacturing process. Laminated structures have a proven history. They were developed in Europe in 1890, and introduced to the United States in 1934. Framing members were introduced in the late 1940s, while poles were introduced in 1963, two years ahead of steel poles. Some of the electrical utility applications include: (1) distribution structures, (2) transmission structures such as single-pole, phase over phase switch structures, tangent structures, and H-Frame construction. The applications for the telecommunication industry consist of joint use structures, such as electric and telecommunication, lighting and telecommunication, overhead telephone and wireless; mono-pole applications; three-pole Bell Towers; and tree poles. Examples of each type were shown. figs.

  5. Synthetic focused array of electrical prospecting using pole-pole array potential data; Sanjigen denki tansaho ni okeru nikyokuho den`i data wo mochiita denryu shusoku haichi no goseiho

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, K. [Central Research Institute of Electric Power Industry, Tokyo (Japan)

    1997-10-22

    Various methods have been put into practice for the conventional two-dimensional pole configuration using a single line in three-dimensional electrical prospecting. Pole configuration effective for the three-dimensional exploration has not been investigated. This paper describes synthetic focused array using four pairs of guarded poles based on pole-pole array potential data in the case of arrangement of measuring points on a grid. Results of the numerical simulation are also described. For the focused array, laterolog of electrical logging is applied to the surface prospecting. Directivity can be given to the current from the main pole by controlling the current from guarded pole. It was found from the simulation that the resistivity anomaly is concentrated directly on the embedded ball for the focused array rather than for the pole-pole array. It was also found that two conductive balls can be clearly separated for the focused array rather than for the dipole-dipole array. Accordingly, it was considered that results approximating the original structures can be obtained by analyzing using the both arrays. 5 refs., 6 figs.

  6. Diet in the management of weight loss

    OpenAIRE

    Strychar, Irene

    2006-01-01

    Obesity is an established risk factor for numerous chronic diseases, and successful treatment will have an important impact on medical resources utilization, health care costs, and patient quality of life. With over 60% of our population being overweight, physicians face a major challenge in assisting patients in the process of weight loss and weight-loss maintenance. Low-calorie diets can lower total body weight by an average of 8% in the short term. These diets are well-tolerated and charac...

  7. Spectral representations of the electron energy loss in composite media

    International Nuclear Information System (INIS)

    Fuchs, R.; Barrera, R.G.; Carrillo, J.L.

    1996-01-01

    Using a recently developed theory for the inverse longitudinal nonlocal dielectric response for a granular composite [R. G. Barrera and R. Fuchs, Phys. Rev. B 52, 3256 (1995)], we find an effective local dielectric response from the condition that it must give the same electron energy-loss probability density as the actual nonlocal response. This local response is expressed as a spectral representation: a sum of terms with simple poles corresponding to the excitation of bulk and interfacial modes. Taking as a guideline the condition that the strength and location of the poles must satisfy sum rules, a single-surface-mode approximation is proposed. This single-mode approximation is tested for a random system of aluminum spheres in vacuum. copyright 1996 The American Physical Society

  8. Analysis of longwall face-to-face transfers

    International Nuclear Information System (INIS)

    Patrick, C.; Topuz, E.

    1992-01-01

    A non-producing longwall costs the mine owner from $45 to over $100 per minute in lost production time. Face-to-face equipment transfers, which involve disassembling longwall equipment in a panel, transporting, and then reassembling it in a new longwall panel, are second only to system availability as a source of longwall non-productive time. This, in addition to a move cost of over $100,000, makes reduction and control of face transfer times essential. This paper will report a segment of on-going VPI research to analyze and model longwall transfers through the use of operations research techniques. The purpose is to reduce overall transfer time and the variation of transfer times among U.S. longwall operations. This research is expected to contribute to the longwall mining industry by offering an objective approach that can be used in the prediction, planning, preparation, and implementation of longwall face equipment transfers

  9. Multithread Face Recognition in Cloud

    Directory of Open Access Journals (Sweden)

    Dakshina Ranjan Kisku

    2016-01-01

    Full Text Available Faces are highly challenging and dynamic objects that are employed as biometrics evidence in identity verification. Recently, biometrics systems have proven to be an essential security tools, in which bulk matching of enrolled people and watch lists is performed every day. To facilitate this process, organizations with large computing facilities need to maintain these facilities. To minimize the burden of maintaining these costly facilities for enrollment and recognition, multinational companies can transfer this responsibility to third-party vendors who can maintain cloud computing infrastructures for recognition. In this paper, we showcase cloud computing-enabled face recognition, which utilizes PCA-characterized face instances and reduces the number of invariant SIFT points that are extracted from each face. To achieve high interclass and low intraclass variances, a set of six PCA-characterized face instances is computed on columns of each face image by varying the number of principal components. Extracted SIFT keypoints are fused using sum and max fusion rules. A novel cohort selection technique is applied to increase the total performance. The proposed protomodel is tested on BioID and FEI face databases, and the efficacy of the system is proven based on the obtained results. We also compare the proposed method with other well-known methods.

  10. Dispersion relation and unphysical poles of Möbius domain-wall fermions in free field theory at finite Ls

    Science.gov (United States)

    Tomii, Masaaki

    2018-03-01

    We investigate the dispersion relation of Möbius domain-wall fermions in free field theory at finite Ls. We find that there are Ls - 1 extra poles of Möbius domain-wall fermions in addition to the pole which realizes the physical mode in the continuum limit. The unphysical contribution of these extra poles could be significant when we introduce heavy quarks. We show in this report the fundamental properties of these unphysical poles and discuss the optimal choice of Möbius parameters to minimize their contribution to four-dimensional physics.

  11. [Separate vertical wiring combined with tension band and Kirschner-wire plus cerclage wire in the treatment of displaced inferior pole fractures of the patella].

    Science.gov (United States)

    Zhang, J; Jiang, X Y; Huang, X W

    2016-06-18

    To investigate the clinical efficacy and outcomes of two separate vertical wiring combined with tension band and Kirschner-wire plus cerclage wire in the treatment of displaced inferior pole fractures of the patella. From January 2013 to January 2015, 15 consecutive patients (mean age 54.5 years) with inferior pole fractures of the patella were retrospectively included in this study. All the patients underwent open reduction and internal fixation by separate vertical wiring combined with tension band and Kirschner-wire plus cerclage wire through longitudinal incision, 4.5 d (range: 3.1-5.9 d) after initial injury. A safety check for early knee range of motion was performed before wound closure. The complications including infection, nonunion, loss of fixation and any wire breakage or irritation from implant were recorded. Anteroposterior and lateral views of the knee joint obtained during the follow-up were used to assess bony union based on the time when the fracture line disappeared. At the time of the final outpatient follow up, functional evaluation of the knee joint was conducted by Bostman system. The follow-up time was 13.1 months (range: 12-19 months) after surgery on average, immediate motion without immobilization in all the cases was allowed and there was no case of reduction loss of the fracture and wire breakage. There was no case of irritation from the implant. At the final follow-up, the average range of motion (ROM) arc was 126.7° (range: 115°-140°), the average ROM lag versus contralateral healthy leg was 10.3° (range: 0°-35°). The mean Bostman score at the last follow-up was 28.9 (range: 27-30), and graded excellent in most cases. Two separate vertical wiring is an easy and effective method to reduce the displaced inferior pole fracture of patella. Augmentation of separate vertical wiring with tension band and Kirschner-wire plus cerclage wire in these patients provides enough strength to protected the early exercise of the knee joint and

  12. Instrument for analysis of electric motors based on slip-poles component

    Science.gov (United States)

    Haynes, H.D.; Ayers, C.W.; Casada, D.A.

    1996-11-26

    A new instrument is described for monitoring the condition and speed of an operating electric motor from a remote location. The slip-poles component is derived from a motor current signal. The magnitude of the slip-poles component provides the basis for a motor condition monitor, while the frequency of the slip-poles component provides the basis for a motor speed monitor. The result is a simple-to-understand motor health monitor in an easy-to-use package. Straightforward indications of motor speed, motor running current, motor condition (e.g., rotor bar condition) and synthesized motor sound (audible indication of motor condition) are provided. With the device, a relatively untrained worker can diagnose electric motors in the field without requiring the presence of a trained engineer or technician. 4 figs.

  13. Improvement of the piezoelectric properties of glass fiber-reinforced epoxy composites by poling treatment

    International Nuclear Information System (INIS)

    Oh, S M; Hwang, H Y

    2013-01-01

    Recently, a new non-destructive method has been proposed for damage monitoring of glass fiber-reinforced polymer composite materials using the piezoelectric characteristics of a polymeric matrix. Several studies of the piezoelectric properties of unidirectional glass fiber epoxy composites and damage monitoring of double-cantilever beams have supported the claim that the piezoelectric method is feasible and powerful enough to monitor the damage of glass fiber epoxy composites. Generally, conventional piezoelectric materials have higher piezoelectric characteristics through poling treatment. In this work, we investigated the change of the piezoelectric properties of glass fiber-reinforced epoxy composites before and after poling treatment. The piezoelectric constants (d 33 ) of glass fiber-reinforced epoxy composites increased by more than 400%. Also, x-ray diffraction tests revealed that poling treatment changed the degree of crystallinity of the epoxy matrix, and this led to the improvement of the piezoelectric characteristics of glass fiber-reinforced epoxy composites. (paper)

  14. A Principle and Winding Design of Consequent-Pole Bearingless Motors

    Science.gov (United States)

    Takenaga, Tomohiro; Kubota, Yutaka; Chiba, Akira; Fukao, Tadashi

    Recently, bearingless motors have been developed to enhance motor drive systems with magnetic suspension. Several types of motors have been proposed as bearingless motors, such as induction, surface mounted permanent magnet, inset permanent magnet, interior permanent magnet, buried permanent magnet, homopolar, hybrid, and switched reluctance bearingless motors. Permanent magnet bearingless motors have been attracting more interests in these years because of the high efficiency. In this paper, a consequent-pole bearingless motor is proposed. A rotor has buried permanent magnets, of which polarities are like. The radial force of a consequent-pole bearingless motor is generated by dc current. Thus, rotational angular position is not needed in a magnetic suspension controller. Radial force variations caused by a rotor rotation are minimized by improving arrangement of stator suspension conductors. A prototype bearingless motor and its controller are built. In experiment, principles of magnetic suspension in the proposed consequent-pole bearingless drive are confirmed.

  15. Biomechanical analysis of double poling in elite cross-country skiers.

    Science.gov (United States)

    Holmberg, Hans-Christer; Lindinger, Stefan; Stöggl, Thomas; Eitzlmair, Erich; Müller, Erich

    2005-05-01

    To further the understanding of double poling (DP) through biomechanical analysis of upper and lower body movements during DP in cross-country (XC) skiing at racing speed. Eleven elite XC skiers performed DP at 85% of their maximal DP velocity (V85%) during roller skiing at 1 degrees inclination on a treadmill. Pole and plantar ground reaction forces, joint angles (elbow, hip, knee, and ankle), cycle characteristics, and electromyography (EMG) of upper and lower body muscles were analyzed. 1) Pole force pattern with initial impact force peak and the following active force peak (PPF) correlated to V85%, (r = 0.66, P biomechanical aspects. Future research should further investigate the relationship between biomechanical and physiological variables and elaborate training models to improve DP performance.

  16. WDR62 is associated with the spindle pole and is mutated in human microcephaly.

    Science.gov (United States)

    Nicholas, Adeline K; Khurshid, Maryam; Désir, Julie; Carvalho, Ofélia P; Cox, James J; Thornton, Gemma; Kausar, Rizwana; Ansar, Muhammad; Ahmad, Wasim; Verloes, Alain; Passemard, Sandrine; Misson, Jean-Paul; Lindsay, Susan; Gergely, Fanni; Dobyns, William B; Roberts, Emma; Abramowicz, Marc; Woods, C Geoffrey

    2010-11-01

    Autosomal recessive primary microcephaly (MCPH) is a disorder of neurodevelopment resulting in a small brain. We identified WDR62 as the second most common cause of MCPH after finding homozygous missense and frame-shifting mutations in seven MCPH families. In human cell lines, we found that WDR62 is a spindle pole protein, as are ASPM and STIL, the MCPH7 and MCHP7 proteins. Mutant WDR62 proteins failed to localize to the mitotic spindle pole. In human and mouse embryonic brain, we found that WDR62 expression was restricted to neural precursors undergoing mitosis. These data lend support to the hypothesis that the exquisite control of the cleavage furrow orientation in mammalian neural precursor cell mitosis, controlled in great part by the centrosomes and spindle poles, is critical both in causing MCPH when perturbed and, when modulated, generating the evolutionarily enlarged human brain.

  17. Comparative analysis of morphogeometric parameters of forward cranial pole depending on type of a skull basis

    Directory of Open Access Journals (Sweden)

    Aleshkina О.Yu.

    2012-03-01

    Full Text Available The purpose of the work is comparison of parameters of a forward cranial pole depending on type of a skull basis. The research material contained 100 adult skulls divided into three craniotypes. The method of craniotopometry was used for measuring the parameters and further calculation of average value and their comparison among themselves. Results. The research helped to reveal that length of a forward cranial pole, length of a lateral part on the right and at the left, a corner f.c.-s-n prevail at flexibasilar craniotype. Conclusions. The width of a forward cranial pole, width of a lateral part on the right and at the left, a corner f.c.-n-g are more at platibasilar craniotype

  18. Efficiency and economic benefits of skipjack pole and line (huhate) in central Moluccas, Indonesia

    Science.gov (United States)

    Siahainenia, Stevanus M.; Hiariey, Johanis; Baskoro, Mulyono S.; Waeleruny, Wellem

    2017-10-01

    Excess fishing capacity is a crucial problem in marine capture fisheries. This phenomenon needed to be investigated regarding sustainability and development of the fishery. This research was aimed at analyzing technical efficiency (TE) and computing financial aspects of the skipjack pole and line. Primary data were collected from the owners of the fishing units at the different size of gross boat tonnage (GT), while secondary data were gathered from official publications relating to this research. Data envelopment analysis (DEA) approach was applied to estimate technical efficiency whereas a selected financial analysis was utilized to calculate economic benefits of the skipjack pole and line business. The fishing units with a size of 26-30 GT provided a higher TE value, and also achieved larger economic benefit values than that of the other fishing units. The empirical results indicate that skipjack pole and line in the size of 26-30 GT is a good fishing gear for the business development in central Moluccas.

  19. Crystalline texture study of Zr-2.5%Nb pressure pipes by DRX pole figures

    International Nuclear Information System (INIS)

    Buioli, C P; Banchik, A D; Vizcaino, P; Samper, R; Testone, S

    2012-01-01

    This work presents the study of crystalline texture of Zr-2.5%Nb pressure tubes (A, B and C); structural components of CANDU nuclear power reactors [1]. The study of texture was made using the RX diffraction technique, making measurements of direct pole figures [2], in a Phillips diffractometer with pole goniometer (IFIR-CONICET). The texture was determined calculating the coefficients of JJ Kearns [3]. The samples used correspond to transversal sections of the tubes, front and back, and were characterized making de measurements of five pole figures with Miller index (001), (100), (101), (102) and (110), in order to represent in a complete way the texture in the material. The calculated Kearns coefficients were compared with the specifications given by the designer of pressure tubes AECL [4] (author)

  20. Formation of spindle poles by dynein/dynactin-dependent transport of NuMA.

    Science.gov (United States)

    Merdes, A; Heald, R; Samejima, K; Earnshaw, W C; Cleveland, D W

    2000-05-15

    NuMA is a large nuclear protein whose relocation to the spindle poles is required for bipolar mitotic spindle assembly. We show here that this process depends on directed NuMA transport toward microtubule minus ends powered by cytoplasmic dynein and its activator dynactin. Upon nuclear envelope breakdown, large cytoplasmic aggregates of green fluorescent protein (GFP)-tagged NuMA stream poleward along spindle fibers in association with the actin-related protein 1 (Arp1) protein of the dynactin complex and cytoplasmic dynein. Immunoprecipitations and gel filtration demonstrate the assembly of a reversible, mitosis-specific complex of NuMA with dynein and dynactin. NuMA transport is required for spindle pole assembly and maintenance, since disruption of the dynactin complex (by increasing the amount of the dynamitin subunit) or dynein function (with an antibody) strongly inhibits NuMA translocation and accumulation and disrupts spindle pole assembly.

  1. Determination of the dominant resonance pole of the three-neutron system

    International Nuclear Information System (INIS)

    Moeller, K.

    1981-03-01

    The resonance behaviour of a system of three neutrons interacting via s-wave separable Yamaguchi potential is considered. For the quantum numbers (T,S,Lsup(π)) = (3/2, 1/2, 1 - ) the dominating pole of the S-matrix is determined by applying contour deformation technique to solve the homogeneous Faddeev equation on the nonphysical sheets of the S-matrix. For the positions and the asymptotic normalization constant of the dominating pole pair the values z 3 = (-88.0 +- i 27.9) keV and Csub(p) 2 = -0.05 +- i 0.1 are obtained. Although the pole pair is close to the real axis in the complex energy plane it is not expected to cause an observable experimental effect due to the smallness of the asymptotic normalization constant. (author)

  2. Electric field poling 2G V/m to improve piezoelectricity of PVDF thin film

    Science.gov (United States)

    Hartono, Ambran; Darwin, Ramli, Satira, Suparno; Djamal, Mitra; Herman

    2016-03-01

    Polyvinylidene fluoride (PVDF) is a polymer with unique characteristics i.e. piezoelectric and ferrroelectric properties. Piezoelectric propertiesof PVDF are determined by the fraction of β-phase structure. Several optimization methods have been developed to improve the piezoelectric properties of PVDF. One of our research efforts is to improve the piezoelectricity of PVDF by electric poling with high electric field 2G V/m. The application of high electric field performed on PVDF films with a thickness of 1 1m. Each sample was made with a deep coating method, with annealing temperature 70°C-110°C. Based on the XRD characterization, we have obtained value of β-fraction of samples after poling are: 56%, 61%, 77%, 81% and 83%, respectively. Therefore, high electric field poling has been able to improve the piezoelectric properties of PVDF films. The PVDF with good piezoelectric properties are potential can did a tes for piezoelectric sensors and actuators devices.

  3. Incidental fear cues increase monetary loss aversion.

    Science.gov (United States)

    Schulreich, Stefan; Gerhardt, Holger; Heekeren, Hauke R

    2016-04-01

    In many everyday decisions, people exhibit loss aversion-a greater sensitivity to losses relative to gains of equal size. Loss aversion is thought to be (at least partly) mediated by emotional--in particular, fear-related--processes. Decision research has shown that even incidental emotions, which are unrelated to the decision at hand, can influence decision making. The effect of incidental fear on loss aversion, however, is thus far unclear. In two studies, we experimentally investigated how incidental fear cues, presented during (Study 1) or before (Study 2) choices to accept or reject mixed gambles over real monetary stakes, influence monetary loss aversion. We find that the presentation of fearful faces, relative to the presentation of neutral faces, increased risk aversion-an effect that could be attributed to increased loss aversion. The size of this effect was moderated by psychopathic personality: Fearless dominance, in particular its interpersonal facet, but not self-centered impulsivity, attenuated the effect of incidental fear cues on loss aversion, consistent with reduced fear reactivity. Together, these results highlight the sensitivity of loss aversion to the affective context. (c) 2016 APA, all rights reserved).

  4. Novel pole-sitter mission concepts for continuous polar remote sensing

    Science.gov (United States)

    Ceriotti, Matteo; Heiligers, Jeannette; McInnes, Colin R.

    2012-09-01

    The pole-sitter concept is a solution to the poor temporal resolution of polar observations from highly inclined, low Earth orbits and the poor high latitude coverage from geostationary orbit. It considers a spacecraft that is continuously above either the North or South Pole and, as such, can provide real-time, continuous and hemispheric coverage of the polar regions. Despite the significant distance from the Earth, the utility of this platform for Earth observation and telecommunications is clear, and applications include polar weather forecasting and atmospheric science, glaciology and ice pack monitoring, ultraviolet imaging for aurora studies, continuous telecommunication links with polar regions, arctic ship routing and support for future high latitude oil and gas exploration. The paper presents a full mission design, including launch (Ariane 5 and Soyuz vehicles), for two propulsion options (a near-term solar electric propulsion (SEP) system and a more advanced combination of a solar sail with an SEP system). An optional transfer from the North Pole to South Pole and vice-versa allows viewing of both poles in summer. The paper furthermore focuses on payloads that could be used in such a mission concept. In particular, by using instruments designed for past deep space missions (DSCOVR), it is estimated that resolutions up to about 20 km/pixel in the visible wavelengths can be obtained. The mass of these instruments is well within the capabilities of the pole-sitter design, allowing an SEP-only mission lifetime of about 4 years, while the SEP/sail propulsion technology enables missions of up to 7 years.

  5. Nordic walking versus walking without poles for rehabilitation with cardiovascular disease: Randomized controlled trial.

    Science.gov (United States)

    Girold, Sébastien; Rousseau, Jérome; Le Gal, Magalie; Coudeyre, Emmanuel; Le Henaff, Jacqueline

    2017-07-01

    With Nordic walking, or walking with poles, one can travel a greater distance and at a higher rate than with walking without poles, but whether the activity is beneficial for patients with cardiovascular disease is unknown. This randomized controlled trial was undertaken to determine whether Nordic walking was more effective than walking without poles on walk distance to support rehabilitation training for patients with acute coronary syndrome (ACS) and peripheral arterial occlusive disease (PAOD). Patients were recruited in a private specialized rehabilitation centre for cardiovascular diseases. The entire protocol, including patient recruitment, took place over 2 months, from September to October 2013. We divided patients into 2 groups: Nordic Walking Group (NWG, n=21) and Walking Group without poles (WG, n=21). All patients followed the same program over 4 weeks, except for the walk performed with or without poles. The main outcome was walk distance on the 6-min walk test. Secondary outcomes were maximum heart rate during exercise and walk distance and power output on a treadmill stress test. We included 42 patients (35 men; mean age 57.2±11 years and BMI 26.5±4.5kg/m 2 ). At the end of the training period, both groups showed improved walk distance on the 6-min walk test and treatment stress test as well as power on the treadmill stress test (Ptraining period, Nordic walking training appeared more efficient than training without poles for increasing walk distance on the 6-min walk test for patients with ACS and PAOD. Copyright © 2017. Published by Elsevier Masson SAS.

  6. PolyPole-1: An accurate numerical algorithm for intra-granular fission gas release

    Energy Technology Data Exchange (ETDEWEB)

    Pizzocri, D.; Rabiti, C.; Luzzi, L.; Barani, T.; Van Uffelen, P.; Pastore, G.

    2016-09-01

    This paper describes the development of a new numerical algorithm (called PolyPole-1) to efficiently solve the equation for intra-granular fission gas release in nuclear fuel. The work was carried out in collaboration with Politecnico di Milano and Institute for Transuranium Elements. The PolyPole-1 algorithms is being implemented in INL's fuels code BISON code as part of BISON's fission gas release model. The transport of fission gas from within the fuel grains to the grain boundaries (intra-granular fission gas release) is a fundamental controlling mechanism of fission gas release and gaseous swelling in nuclear fuel. Hence, accurate numerical solution of the corresponding mathematical problem needs to be included in fission gas behaviour models used in fuel performance codes. Under the assumption of equilibrium between trapping and resolution, the process can be described mathematically by a single diffusion equation for the gas atom concentration in a grain. In this work, we propose a new numerical algorithm (PolyPole-1) to efficiently solve the fission gas diffusion equation in time-varying conditions. The PolyPole-1 algorithm is based on the analytic modal solution of the diffusion equation for constant conditions, with the addition of polynomial corrective terms that embody the information on the deviation from constant conditions. The new algorithm is verified by comparing the results to a finite difference solution over a large number of randomly generated operation histories. Furthermore, comparison to state-of-the-art algorithms used in fuel performance codes demonstrates that the accuracy of the PolyPole-1 solution is superior to other algorithms, with similar computational effort. Finally, the concept of PolyPole-1 may be extended to the solution of the general problem of intra-granular fission gas diffusion during non-equilibrium trapping and resolution, which will be the subject of future work.

  7. Aging changes in the face

    Science.gov (United States)

    ... MedlinePlus Site Map FAQs Customer Support Health Topics Drugs & Supplements Videos & Tools Español You Are Here: Home → Medical Encyclopedia → Aging changes in the face URL of this page: // ...

  8. Similarity measures for face recognition

    CERN Document Server

    Vezzetti, Enrico

    2015-01-01

    Face recognition has several applications, including security, such as (authentication and identification of device users and criminal suspects), and in medicine (corrective surgery and diagnosis). Facial recognition programs rely on algorithms that can compare and compute the similarity between two sets of images. This eBook explains some of the similarity measures used in facial recognition systems in a single volume. Readers will learn about various measures including Minkowski distances, Mahalanobis distances, Hansdorff distances, cosine-based distances, among other methods. The book also summarizes errors that may occur in face recognition methods. Computer scientists "facing face" and looking to select and test different methods of computing similarities will benefit from this book. The book is also useful tool for students undertaking computer vision courses.

  9. Face Recognition using Approximate Arithmetic

    DEFF Research Database (Denmark)

    Marso, Karol

    Face recognition is image processing technique which aims to identify human faces and found its use in various different fields for example in security. Throughout the years this field evolved and there are many approaches and many different algorithms which aim to make the face recognition as effective...... as possible. The use of different approaches such as neural networks and machine learning can lead to fast and efficient solutions however, these solutions are expensive in terms of hardware resources and power consumption. A possible solution to this problem can be use of approximate arithmetic. In many image...... processing applications the results do not need to be completely precise and use of the approximate arithmetic can lead to reduction in terms of delay, space and power consumption. In this paper we examine possible use of approximate arithmetic in face recognition using Eigenfaces algorithm....

  10. Bracing Zonohedra With Special Faces

    Directory of Open Access Journals (Sweden)

    Nagy Gyula

    2015-12-01

    Full Text Available The analysis of simpler preliminary design gives useful input for more complicated three-dimensional building frame structure. A zonohedron, as a preliminary structure of design, is a convex polyhedron for which each face possesses central symmetry. We considered zonohedron as a special framework with the special assumption that the polygonal faces can be deformed in such a way that faces remain planar and centrally symmetric, moreover the length of all edges remains unchanged. Introducing some diagonal braces we got a new mechanism. This paper deals with the flexibility of this kind of mechanisms, and investigates the rigidity of the braced framework. The flexibility of the framework can be characterized by some vectors, which represent equivalence classes of the edges. A necessary and sufficient condition for the rigidity of the braced rhombic face zonohedra is posed. A real mechanical construction, based on two simple elements, provides a CAD prototype of these new mechanisms.

  11. Familiarity facilitates feature-based face processing

    Science.gov (United States)

    Wheeler, Kelsey G.; Cipolli, Carlo; Gobbini, M. Ida

    2017-01-01

    Recognition of personally familiar faces is remarkably efficient, effortless and robust. We asked if feature-based face processing facilitates detection of familiar faces by testing the effect of face inversion on a visual search task for familiar and unfamiliar faces. Because face inversion disrupts configural and holistic face processing, we hypothesized that inversion would diminish the familiarity advantage to the extent that it is mediated by such processing. Subjects detected personally familiar and stranger target faces in arrays of two, four, or six face images. Subjects showed significant facilitation of personally familiar face detection for both upright and inverted faces. The effect of familiarity on target absent trials, which involved only rejection of unfamiliar face distractors, suggests that familiarity facilitates rejection of unfamiliar distractors as well as detection of familiar targets. The preserved familiarity effect for inverted faces suggests that facilitation of face detection afforded by familiarity reflects mostly feature-based processes. PMID:28582439

  12. An improved torque density Modulated Pole Machine for low speed high torque applications

    DEFF Research Database (Denmark)

    Washington, J. G.; Atkinson, G. J.; Baker, N. J.

    2012-01-01

    This paper presents a new topology for three-phase Modulated Pole Machines. This new topology the “Combined Phase Modulated Pole Machine” is analysed and compared to the more traditional technology of three separate single phase units stacked axially with a separation between phases. Three......- dimensional Finite Element calculations are used to compare performance of the machines under the same conditions, it is shown that the new Combined Phase topology produces a greater torque whilst reducing the number of components required to assemble the machine and increasing its mechanical integrity....

  13. Interference effect of edge radiation at three-pole wiggler section

    International Nuclear Information System (INIS)

    Koda, Shigeru; Takabayashi, Yuichi

    2016-01-01

    Radiation from a three-pole wiggler section is not simply treated as typical synchrotron radiation in a long-wavelength region. The interference effect between edge radiations from upstream and downstream straight subsections of the wiggler is considered to contribute significantly to the radiation. Our simple model roughly reproduced spectral and spatial distributions of the radiation. Under the maximum interference condition, the peak radiation intensity is four times larger than the edge radiation from a single straight section. Moreover, the longitudinal periodic alignment of three-pole wigglers, which satisfies the maximum interference condition, generates radiation of higher intensity proportional to the square of the periodic number. (author)

  14. WDR62 is associated with the spindle pole and is mutated in human microcephaly

    OpenAIRE

    Nicholas, Adeline K; Khurshid, Maryam; Désir, Julie; Carvalho, Ofélia P; Cox, James J; Thornton, Gemma; Kausar, Rizwana; Ansar, Muhammad; Ahmad, Wasim; Verloes, Alain; Passemard, Sandrine; Misson, Jean-Paul; Lindsay, Susan; Gergely, Fanni; Dobyns, William B

    2010-01-01

    Autosomal recessive primary microcephaly (MCPH) is a disorder of neurodevelopment resulting in a small brain1,2. We identified WDR62 as the second most common cause of MCPH after finding homozygous missense and frame-shifting mutations in seven MCPH families. In human cell lines, we found that WDR62 is a spindle pole protein, as are ASPM and STIL, the MCPH7 and MCHP7 proteins3–5. Mutant WDR62 proteins failed to localize to the mitotic spindle pole. In human and mouse embryonic brain, we found...

  15. Transcendental and interpolation methods in simultaneous stabilization and simultaneous partial pole placement problems

    Science.gov (United States)

    Ghosh, B. K.

    1986-01-01

    The existence of a compensator which simultaneously renders a given r-tuple of multiinput-multioutput p x m linear dynamical systems internally stable is investigated. In particular, a set of simultaneously stabilizable r-tuples of plants is parametrized, and it is shown that, provided r = max(m,p) or less, the above set is semialgebraic and dense in the space Sigma of r-tuples of plants. An extension of the classical pole placement and stabilization problems is considered, and the simultaneous partial pole placement problem is investigated.

  16. Pulsed field magnetization strategies and the field poles composition in a bulk-type superconducting motor

    International Nuclear Information System (INIS)

    Huang, Zhen; Ruiz, H.S.; Coombs, T.A.

    2017-01-01

    Highlights: • Different compositions of the magnetic poles have been obtained depending on the relative orientation of the magnetizing coil and the surfaces of the columns of bulks that conform a magnetic pole. • Two bidimensional models accounting for the electromagnetic response of the top and lateral cross sections of three columns of HTS bulks subjected to multiple pulsed magnetic fields have been created. • An extended PFM strategy has been proposed by considering the magnetization of at least three successive columns of HTS bulks per pole. In the extended PFM strategy the area of each one of the poles can be seen increased by a factor of 200%-400% - Abstract: High temperature superconducting (HTS) bulks offer the potential of trapping and maintaining much higher magnetic loading level compared with the conventional permanent magnets used in rotary machines, although the effective magnetization of multiple HTS bulks with different relative orientations over the surface of cylindrical rotors creates new challenges. In this paper, we present the design and numerical validation of the Pulse Field Magnetization (PFM) strategy considered for the magnetization of the four-pole synchronous fully superconducting motor developed at the University of Cambridge. In a first instance, singular columns of up to five HTS bulks aligned over the height of the rotor were subjected to up to three magnetic pulses of 1.5 T peak, and the experimental results have been simulated by considering the electrical and thermal properties of the system in a 2D approach. The entire active surface of the rotor is covered by HTS bulks of approximately the same dimensions, resulting in an uneven distribution of pole areas with at least one of the poles formed by up to 3 columns of magnetized bulks, with relatively the same peaks of trapped magnetic field. Thus, in order to effectively use the entire area of the superconducting rotor, multiple pulsed fields per column have been applied

  17. Pulsed field magnetization strategies and the field poles composition in a bulk-type superconducting motor

    Energy Technology Data Exchange (ETDEWEB)

    Huang, Zhen, E-mail: zhen.huang@sjtu.edu.cn [Academy of Information Technology and Electrical Engineering, Shanghai Jiao Tong University, 800 Dongchuan Road, Shanghai 200240 (China); Ruiz, H.S., E-mail: dr.harold.ruiz@le.ac.uk [Department of Engineering, University of Leicester, University Road, Leicester LE1 7RH (United Kingdom); Coombs, T.A., E-mail: tac1000@cam.ac.uk [Department of Engineering, University of Cambridge, 9 JJ Thomson Avenue, Cambridge CB3 0FA (United Kingdom)

    2017-03-15

    Highlights: • Different compositions of the magnetic poles have been obtained depending on the relative orientation of the magnetizing coil and the surfaces of the columns of bulks that conform a magnetic pole. • Two bidimensional models accounting for the electromagnetic response of the top and lateral cross sections of three columns of HTS bulks subjected to multiple pulsed magnetic fields have been created. • An extended PFM strategy has been proposed by considering the magnetization of at least three successive columns of HTS bulks per pole. In the extended PFM strategy the area of each one of the poles can be seen increased by a factor of 200%-400% - Abstract: High temperature superconducting (HTS) bulks offer the potential of trapping and maintaining much higher magnetic loading level compared with the conventional permanent magnets used in rotary machines, although the effective magnetization of multiple HTS bulks with different relative orientations over the surface of cylindrical rotors creates new challenges. In this paper, we present the design and numerical validation of the Pulse Field Magnetization (PFM) strategy considered for the magnetization of the four-pole synchronous fully superconducting motor developed at the University of Cambridge. In a first instance, singular columns of up to five HTS bulks aligned over the height of the rotor were subjected to up to three magnetic pulses of 1.5 T peak, and the experimental results have been simulated by considering the electrical and thermal properties of the system in a 2D approach. The entire active surface of the rotor is covered by HTS bulks of approximately the same dimensions, resulting in an uneven distribution of pole areas with at least one of the poles formed by up to 3 columns of magnetized bulks, with relatively the same peaks of trapped magnetic field. Thus, in order to effectively use the entire area of the superconducting rotor, multiple pulsed fields per column have been applied

  18. The south pole region of the moon as seen by Clementine

    Science.gov (United States)

    Shoemaker, E.M.; Robinson, M.S.; Eliason, E.M.

    1994-01-01

    The Clementine mission has provided the first comprehensive set of high-resolution images of the south pole region of the moon. Within 5?? of latitude of the pole, an area of an estimated 30,000 square kilometers remained in shadow during a full lunar rotation and is a promising target for future exploration for ice deposits. The Schrodinger Basin (320 kilometers in diameter), centered at 75??S, is one of the two youngest, least modified, great multiring impact basins on the moon. A large maar-type volcano localized along a graben within the Schrodinger Basin probably erupted between 1 and 2 billion years ago.

  19. A magnetostatic calculation of fringing field for the Rogowski pole boundary with floating snake

    International Nuclear Information System (INIS)

    Yan Chen; Fan Ming-Wu

    1984-01-01

    A boundary integral method has been used to calculate the fringing field distribution of Rogowski pole boundary with floating snake for QMG2 type of QDDD magnetic spectrograph and the experimental EFB is nearly reproduced from BIM calculation. As a further criteria, a calculation for clamped Rogowski pole but without snake is also performed and the calculated EFB shows perfect identity with the experiment. For evaluating the effect of snake quantitatively, this work also predicts the EFB values for two different positions of snake

  20. THEORIES REGARDING THE ROLE OF THE GROWTH POLES IN THE EUROPEAN ECONOMIC INTEGRATION

    Directory of Open Access Journals (Sweden)

    Laurentia Georgeta Avram

    2017-06-01

    Full Text Available The specialized literature stressed very little or not at all the role of the growth poles in the economic integration, although the development of the national economies depend on connecting the major urban centers in the regional economic system, continental and global levels. Conversely, integration and globalization of the economic, socio-political, cultural and the transition to a knowledge economy seem to be major factors in the transformation and restructuring of the growth poles and the urban systems dependent on them.

  1. Kõiges pole süüdi britid / Toomas Hendrik Ilves

    Index Scriptorium Estoniae

    Ilves, Toomas Hendrik, 1953-

    2005-01-01

    Ilmunud ka: Postimees : na russkom jazõke 14. dets. lk. 7. Euroopa Parlamendi väliskomisjoni aseesimees rõhutab, et EL-i eelarvekava keskmes pole mitte uutele liikmesriikidele antav raha, vaid põllumajandustoetuste reformimine, mille peamised kasusaajad on EL-is praegu käputäis suurtootjaid. 1% ehk 2530 prantsuse farmerit saavad 13% ehk 80 miljardit krooni EL-i põllumajandusrahast aastas. Ka Eestis pole põllumajandusministeerium nõus otsetoetuste saajaid avalikustama ning kohalikud teadlased on välja arvutanud, et ka siinsed suhtarvud sarnanevad suuresti Prantsusmaa vastavate arvudega

  2. A ZMP-Compensation Method Based on Pole-Zero Cancellation for Biped Robots

    Science.gov (United States)

    Shimmyo, Shuhei; Ohnishi, Kouhei

    This paper proposes a ZMP-compensation method based on pole-zero cancellation for biped robots. Conventionally, walking stabilization controls is achieved by using the feedback of ZMP error. In these systems, several feedback gains need to be determined, and this is done by using the optimal control theory or the pole-placement method. In the proposed method, only one feedback gain needs to be determined. Therefore, the proposed method makes it easy to design a walking stabilization controller. The effectiveness of the proposed method is confirmed from the results of simulations and experiments.

  3. Raman Probe Based on Optically-Poled Double-Core Fiber

    DEFF Research Database (Denmark)

    Brunetti, Anna Chiara; Margulis, Walter; Rottwitt, Karsten

    2012-01-01

    A Raman probe based on an optically-poled double-core fiber. In-fiber SHG allows for Raman spectroscopy of DMSO at 532nm when illuminating the fiber with 1064nm light. The fiber structure provides independent excitation and collection paths.......A Raman probe based on an optically-poled double-core fiber. In-fiber SHG allows for Raman spectroscopy of DMSO at 532nm when illuminating the fiber with 1064nm light. The fiber structure provides independent excitation and collection paths....

  4. 3D Face Appearance Model

    DEFF Research Database (Denmark)

    Lading, Brian; Larsen, Rasmus; Åström, Kalle

    2006-01-01

    We build a 3d face shape model, including inter- and intra-shape variations, derive the analytical jacobian of its resulting 2d rendered image, and show example of its fitting performance with light, pose, id, expression and texture variations.}......We build a 3d face shape model, including inter- and intra-shape variations, derive the analytical jacobian of its resulting 2d rendered image, and show example of its fitting performance with light, pose, id, expression and texture variations.}...

  5. 3D Face Apperance Model

    DEFF Research Database (Denmark)

    Lading, Brian; Larsen, Rasmus; Astrom, K

    2006-01-01

    We build a 3D face shape model, including inter- and intra-shape variations, derive the analytical Jacobian of its resulting 2D rendered image, and show example of its fitting performance with light, pose, id, expression and texture variations......We build a 3D face shape model, including inter- and intra-shape variations, derive the analytical Jacobian of its resulting 2D rendered image, and show example of its fitting performance with light, pose, id, expression and texture variations...

  6. On Loss Aversion in Capuchin Monkeys

    Science.gov (United States)

    Silberberg, Alan; Roma, Peter G.; Huntsberry, Mary E.; Warren-Boulton, Frederick R.; Sakagami, Takayuki; Ruggiero, Angela M.; Suomi, Stephen J.

    2008-01-01

    Chen, Lakshminarayanan, and Santos (2006) claim to show in three choice experiments that monkeys react rationally to price and wealth shocks, but, when faced with gambles, display hallmark, human-like biases that include loss aversion. We present three experiments with monkeys and humans consistent with a reinterpretation of their data that…

  7. Threatening faces induce fear circuitry hypersynchrony in soldiers with post-traumatic stress disorder.

    Science.gov (United States)

    Dunkley, Benjamin T; Pang, Elizabeth W; Sedge, Paul A; Jetly, Rakesh; Doesburg, Sam M; Taylor, Margot J

    2016-01-01

    Post-traumatic stress disorder (PTSD) is associated with atypical responses to emotional face stimuli with preferential processing given to threat-related facial expressions via hyperactive amygdalae disengaged from medial prefrontal modulation. We examined implicit emotional face perception in soldiers with (n = 20) and without (n = 25) PTSD using magnetoencephalography to define spatiotemporal network interactions, and a subsequent region-of-interest analysis to characterize the network role of the right amygdala and medial prefrontal cortex in threatening face perception. Contrasts of network interactions revealed the PTSD group were hyperconnected compared to controls in the phase-locking response in the 2-24 Hz range for angry faces, but not for happy faces when contrasting groups. Hyperconnectivity in PTSD was greatest in the posterior cingulate, right ventromedial prefrontal cortex, right parietal regions and the right temporal pole, as well as the right amygdala. Graph measures of right amygdala and medial prefrontal connectivity revealed increases in node strength and clustering in PTSD, but not inter-node connectivity. Additionally, these measures were found to correlate with anxiety and depression. In line with prior studies, amygdala hyperconnectivity was observed in PTSD in relation to threatening faces, but the medial prefrontal cortex also displayed enhanced connectivity in our network-based approach. Overall, these results support preferential neurophysiological encoding of threat-related facial expressions in those with PTSD.

  8. Small scale farmers' knowledge on grain losses from bean bruchid ...

    African Journals Online (AJOL)

    Small scale farmers' knowledge on grain losses from bean bruchid, pesticides safe use and implication on food security and safety in Huye District, Rwanda. ... We used questionnaires and face to face interviews to collect data on bean bruchid, control methods, pesticide use and safety measures. The results indicate that ...

  9. Face adaptation: Changing stable representations of familiar faces within minutes?

    Directory of Open Access Journals (Sweden)

    Claus-Christian Carbon

    2005-01-01

    Full Text Available Three experiments are reported showing that the perception and the assessment of veridicality of familiar faces are highly adaptive to new visual information. Subjects were asked to discriminate between real photographs and altered versions of celebrities. Exposing participants to extremely deviated versions changed the usually stable representations of the famous faces within a very short time. In Experiment 1, exposure to an extreme face version resulted in identity decisions shifted towards the exposed one. Experiment 2 revealed that the effects are not short lasting. In Experiment 3, we showed that the effect also generalizes to different pictures of the same famous person. Together the experiments seem to indicate that the brain permanently adapts to new perceptual information and integrates new data within already elaborated representations in a fast way.

  10. Analysis and Development of FACE Automatic Apparatus for Rapid Identification of Transuranium Isotopes

    Energy Technology Data Exchange (ETDEWEB)

    Sebesta, Edward Henri [Univ. of California, Berkeley, CA (United States)

    1978-09-01

    A description of and operating manual for the FACE Automatic Apparatus has been written along with a documentation of the FACE machine operating program, to provide a user manual for the FACE Automatic Apparatus. In addition, FACE machine performance was investigated to improve transuranium throughput. Analysis of the causes of transuranium isotope loss was undertaken both chemical and radioactive. To lower radioactive loss, the dynamics of the most time consuming step of the FACE machine, the chromatographic column output droplet drying and flaming, in preparation of sample for alpha spectroscopy and counting, was investigated. A series of droplets were dried in an experimental apparatus demonstrating that droplets could be dried significantly faster through more intensie heating, enabling the FACE machine cycle to be shortened by 30-60 seconds. Proposals incorporating these ideas were provided for FACE machine development. The 66% chemical loss of product was analyzed and changes were proposed to reduce the radioisotopes product loss. An analysis of the chromatographic column was also provided. All operating steps in the FACE machine are described and analyzed to provide a complete guide, along with the proposals for machine improvement.

  11. A variational EM method for pole-zero modeling of speech with mixed block sparse and Gaussian excitation

    DEFF Research Database (Denmark)

    Shi, Liming; Nielsen, Jesper Kjær; Jensen, Jesper Rindom

    2017-01-01

    the posterior PDFs of the block sparse residuals and point estimates of mod- elling parameters within a sparse Bayesian learning framework. Compared to conventional pole-zero and all-pole based methods, experimental results show that the proposed method has lower spectral distortion and good performance...

  12. Analysis of the state of poling of lead zirconate titanate (PZT) particles in a Zn-ionomer composite

    NARCIS (Netherlands)

    James, N.K.; Comyn, T.; Hall, D.; Daniel, L.; Kleppe, A.; Zwaag, S. van der; Groen, W.A.

    2016-01-01

    The poling behaviour of tetragonal lead zirconate titanate (PZT) piezoelectric ceramic particles in a weakly conductive ionomer polymer matrix is investigated using high energy synchrotron X-ray diffraction analysis. The poling efficiency, crystallographic texture and lattice strain of the PZT

  13. Removal of creosote from wood particles at different horizontal and vertical locations of decommissioned poles using steam treatment

    Science.gov (United States)

    Todd F. Shupe; Chung Y. Hse; Han Roliadi

    2006-01-01

    This study used steam treatment to evaluate the potential of this method to remove residual creosote content of sawdust from weathered, out-of-service poles. Steaming was successful in reducing the creosote content to a level of 1.31%, regardless of creosote content at the start of the steaming treatment. Poles with higher initial creosote contents required longer...

  14. Vallandatud juht: sain suurepäraselt hakkama / Igor Poleštšuk

    Index Scriptorium Estoniae

    Poleštšuk, Igor

    2009-01-01

    2008. aasta detsembris Kreenholmi tegevjuhiks valitud ning neli kuud hiljem vallandatud Igor Poleštšuk vastab küsimustele, mis puudutavad Kreenholmi omanike vallandamisotsust ja ärimudelit, vastuolusid omanike ja Rootsis asuva tegevjuhtkonna vahel, Kreenholmis saavutatud tulemusi ning Kreenholmi edasist saatust

  15. From Beale Number to Pole Placement Design of a Free Piston Stirling Engine

    Directory of Open Access Journals (Sweden)

    Zare Shahryar

    2017-12-01

    Full Text Available In this paper, pole placement-based design and analysis of a free piston Stirling engine (FPSE is presented and compared to the well-defined Beale number design technique. First, dynamic and thermodynamic equations governing the engine system are extracted. Then, linear dynamics of the free piston Stirling engine are studied using dynamic systems theory tools such as root locus. Accordingly, the effects of variations of design parameters such as mass of pistons, stiffness of springs, and frictional damping on the locations of dominant closed-loop poles are investigated. The design procedure is thus conducted to place the dominant poles of the dynamic system at desired locations on the s-plane so that the unstable dynamics, which is the required criterion for energy generation, is achieved. Next, the closed-loop poles are selected based on a desired frequency so that a periodical system is found. Consequently, the design parameters, including mass and spring stiffness for both power and displacer pistons, are obtained. Finally, the engine power is calculated through the proposed control-based analysis and the result is compared to those of the experimental work and the Beale number approach. The outcomes of this work clearly reveal the effectiveness of the control-based design technique of FPSEs compared to the well-known approaches such as Beale number.

  16. Lower pole caliceal stone clearance after ESWL: the effect of infundibulopelvic angle.

    Science.gov (United States)

    Lojanapiwat, B; Soonthornpun, S; Wudhikarn, S

    1999-09-01

    Extracorporeal Shock Wave Lithotripsy (ESWL) represents the first choice therapy for renoureteral stone disease. Clinical controversy exists concerning the efficacy of ESWL for lower pole kidney stones. Nowadays, the factors that hinder the spontaneous passage of stone debris that results from ESWL of lower caliceal stone are the gravity-dependent position of the lower pole calices and particular features of the inferior-pole collecting system anatomy. We studied the influence of the lower infundibulo-pelvic in the success of ESWL of lower caliceal stones 10-20 millimeters in size in 50 patients with STORZ MODULITH SL-20 machine. At the mean follow-up of 6 months, only 44 per cent of the patients presenting with an infundibulo-pelvic angle of les than 90 degrees became stone free. On the other hand, 86 per cent of the patients presenting with an infundibulo-pelvic angle of greater than 90 degrees became stone free. Our data suggest that acute infundibulo-pelvic angle of the lower pole hinders the spontaneous passage of fragments after ESWL.

  17. Prototype crawling robotics system for remote visual inspection of high-mast light poles.

    Science.gov (United States)

    1997-01-01

    This report presents the results of a project to develop a crawling robotics system for the remote visual inspection of high-mast light poles in Virginia. The first priority of this study was to develop a simple robotics application that would reduce...

  18. Lunar Pole Illumination and Communications Maps Computed from GSSR Elevation Data

    Science.gov (United States)

    Bryant, Scott

    2009-01-01

    A Digital Elevation Model of the lunar south pole was produced using Goldstone Solar System RADAR (GSSR) data obtained in 2006.12 This model has 40-meter horizontal resolution and about 5-meter relative vertical accuracy. This Digital Elevation Model was used to compute average solar illumination and Earth visibility with 100 kilometers of the lunar south pole. The elevation data were converted into local terrain horizon masks, then converted into lunar-centric latitude and longitude coordinates. The horizon masks were compared to latitude, longitude regions bounding the maximum Sun and Earth motions relative to the moon. Estimates of Earth visibility were computed by integrating the area of the region bounding the Earth's motion that was below the horizon mask. Solar illumination and other metrics were computed similarly. Proposed lunar south pole base sites were examined in detail, with the best site showing yearly solar power availability of 92 percent and Direct-To-Earth (DTE) communication availability of about 50 percent. Similar analysis of the lunar south pole used an older GSSR Digital Elevation Model with 600-meter horizontal resolution. The paper also explores using a heliostat to reduce the photovoltaic power system mass and complexity.

  19. Scientific Goals of the IceCube Neutrino Detector at the South Pole

    CERN Document Server

    Goldschmidt, A

    2002-01-01

    IceCube is a proposed ice-Cherenkov kilometer scale neutrino telescope, to be located at the South Pole. Its science potential covers a wide range of topics from Active Galatic Nuclei and Gamma Ray Bursters neutrino emission to WIMP annihilation into neutrinos.

  20. Pulsed field magnetization strategies and the field poles composition in a bulk-type superconducting motor

    Science.gov (United States)

    Huang, Zhen; Ruiz, H. S.; Coombs, T. A.

    2017-03-01

    High temperature superconducting (HTS) bulks offer the potential of trapping and maintaining much higher magnetic loading level compared with the conventional permanent magnets used in rotary machines, although the effective magnetization of multiple HTS bulks with different relative orientations over the surface of cylindrical rotors creates new challenges. In this paper, we present the design and numerical validation of the Pulse Field Magnetization (PFM) strategy considered for the magnetization of the four-pole synchronous fully superconducting motor developed at the University of Cambridge. In a first instance, singular columns of up to five HTS bulks aligned over the height of the rotor were subjected to up to three magnetic pulses of 1.5 T peak, and the experimental results have been simulated by considering the electrical and thermal properties of the system in a 2D approach. The entire active surface of the rotor is covered by HTS bulks of approximately the same dimensions, resulting in an uneven distribution of pole areas with at least one of the poles formed by up to 3 columns of magnetized bulks, with relatively the same peaks of trapped magnetic field. Thus, in order to effectively use the entire area of the superconducting rotor, multiple pulsed fields per column have been applied under the same experimental conditions, what results in about three times larger magnetic pole areas but with an average drop on the peaks of trapped magnetic field of about 50%.

  1. Continuous Planetary Polar Observation from Hybrid Pole-Sitters at Venus, Earth, and Mars

    NARCIS (Netherlands)

    Heiligers, M.J.; van den Oever (student TUDelft), Tom; Ceriotti, M.; Mulligan, P.; McInnes, CR

    2017-01-01

    A pole-sitter is a satellite that is stationed along the polar axis of the Earth, or any other planet, to generate a continuous, hemispherical view of the planet’s polar regions. In order to maintain such a vantage point, a low-thrust propulsion system is required to counterbalance the gravitational

  2. 3-D finite element analysis of claw-poled stepping motor

    International Nuclear Information System (INIS)

    Kawase, Yoshihiro; Yamaguchi, Tadashi; Mizuno; Koike, Yoshikazu

    2002-01-01

    Stepping motors are widely used for various electric instruments. It is necessary for the optimum design to analyze the magnetic field accurately. The 3-D finite element method with edge elements taking into account the rotation of the rotor has been applied to analyze the magnetic field of a claw-poled stepping motor. (Author)

  3. Experience on impregnation of wood.en poles with water borne salts

    African Journals Online (AJOL)

    I. Leechability. Since the process depends on osmosis, the preservative must be highly soluble in water and ... treating plant where the FU LL CELL method can be employed to be more suitable. In June 1961 the plant was acquired from Sweden and treating of poles commenced using a water borne preservative commonly ...

  4. Phloem unloading in Arabidopsis roots is convective and regulated by the phloem-pole pericycle

    DEFF Research Database (Denmark)

    Ross-Elliott, Timothy J.; Jensen, Kaare Hartvig; Haaning, Katrine S.

    2017-01-01

    by a unique class of 'funnel plasmodesmata'. While solutes are unloaded without restriction, large proteins are released through funnel plasmodesmata in discrete pulses, a phenomenon we refer to as 'batch unloading'. Unlike solutes, these proteins remain restricted to the phloem-pole pericycle. Our data...

  5. Building Peace Poles: Inexpensive Woodworking Project Great for Middle and High School Students

    Science.gov (United States)

    Roccanova, John

    2013-01-01

    The World Peace Prayer Society (WPPS) has at its core the message: "May peace prevail on Earth." This axiom appears on the roughly 200,000 Peace Poles that are planted at private residences, schools, in parks, and at other public places worldwide including at the Pentagon, the Pyramids in Egypt, and on Mt. Kilimanjaro, the highest free-standing…

  6. On the factorization of universal poles in a theory of gravitating point particles.

    NARCIS (Netherlands)

    Hooft, G. 't

    1988-01-01

    A theory is considered in which point-like particles scatter only gravitationally and electromagnetically but no other exchanges are taken into account. The two-particle amplitude at high s, low t, as computed before, has universal poles at s values whose imaginary parts are integer positive numbers

  7. Siim Kallas: Rail Baltica edeneb, aga veel pole mõtet kiirrongi oodata / Urmas Jaagant

    Index Scriptorium Estoniae

    Jaagant, Urmas

    2010-01-01

    Euroopa Komisjoni voliniku Siim Kallase sõnul pole mingit põhjust, miks Eestis ei võiks sõita 200 km/h liikuvad kiirrongid, vajaliku raudtee ehitamine võib olla isegi odavam kui uus maantee. Kuid oluline on küsimus, kuidas tekitada erasektoris piisavalt suur kindlustunne, et Rail Baltica projekt ära tasub

  8. Morpho-functional characterization of the systemic venous pole of the reptile heart

    NARCIS (Netherlands)

    Jensen, Bjarke; Vesterskov, Signe; Boukens, Bastiaan J.; Nielsen, Jan M.; Moorman, Antoon F. M.; Christoffels, Vincent M.; Wang, Tobias

    2017-01-01

    Mammals evolved from reptile-like ancestors, and while the mammalian heart is driven by a distinct sinus node, a sinus node is not apparent in reptiles. We characterized the myocardial systemic venous pole, the sinus venosus, in reptiles to identify the dominant pacemaker and to assess whether the

  9. Kvoodimüügilt teenitud miljardid pole Eestis saastamist vähendanud / Raimo Poom

    Index Scriptorium Estoniae

    Poom, Raimo

    2007-01-01

    Autori väitel pole Eesti Energia süsihappegaasi kasutamata kvoodi müügist teenitud peaaegu 3 miljardist seni CO₂ õhkupaiskamist vähendavatesse projektidesse midagi paigutanud. Eesti Energia finantsdirektori Margus Kaasiku selgitus. Lisa: Eesti tuleks toime väiksema kvoodiga

  10. Effect of the upper limbs muscles activity on the mechanical energy gain in pole vaulting.

    Science.gov (United States)

    Frère, Julien; Göpfert, Beat; Slawinski, Jean; Tourny-chollet, Claire

    2012-04-01

    The shoulder muscles are highly solicited in pole vaulting and may afford energy gain. The objective of this study was to determine the bilateral muscle activity of the upper-limbs to explain the actions performed by the vaulter to bend the pole and store elastic energy. Seven experienced athletes performed 5-10 vaults which were recorded using two video cameras (50Hz). The mechanical energy of the centre of gravity (CG) was computed, while surface electromyographic (EMG) profiles were recorded from 5 muscles bilateral: deltoideus, infraspinatus, biceps brachii, triceps, and latissimus dorsi muscles. The level of intensity from EMG profile was retained in four sub phases between take-off (TO1) and complete pole straightening (PS). The athletes had a mean mechanical energy gain of 22% throughout the pole vault, while the intensities of deltoideus, biceps brachii, and latissimus dorsi muscles were sub phases-dependent (pmuscle activation. The gain in mechanical energy of the vaulter could be linked to an increase in muscle activation, especially from latissimusdorsi muscles. Copyright © 2011 Elsevier Ltd. All rights reserved.

  11. Development of a neurofeedback protocol targeting the frontal pole using near-infrared spectroscopy.

    Science.gov (United States)

    Kinoshita, Akihide; Takizawa, Ryu; Yahata, Noriaki; Homae, Fumitaka; Hashimoto, Ryuichiro; Sakakibara, Eisuke; Kawasaki, Shingo; Nishimura, Yukika; Koike, Shinsuke; Kasai, Kiyoto

    2016-11-01

    Neurofeedback has been studied with the aim of controlling cerebral activity. Near-infrared spectroscopy is a non-invasive neuroimaging technique used for measuring hemoglobin concentration changes in cortical surface areas with high temporal resolution. Thus, near-infrared spectroscopy may be useful for neurofeedback, which requires real-time feedback of repeated brain activation measurements. However, no study has specifically targeted neurofeedback, using near-infrared spectroscopy, in the frontal pole cortex. We developed an original near-infrared spectroscopy neurofeedback system targeting the frontal pole cortex. Over a single day of testing, each healthy participant (n = 24) received either correct or incorrect (Sham) feedback from near-infrared spectroscopy signals, based on a crossover design. Under correct feedback conditions, significant activation was observed in the frontal pole cortex (P = 0.000073). Additionally, self-evaluation of control and metacognitive beliefs were associated with near-infrared spectroscopy signals (P = 0.006). The neurofeedback system developed in this study might be useful for developing control of frontal pole cortex activation. © 2016 The Authors. Psychiatry and Clinical Neurosciences © 2016 Japanese Society of Psychiatry and Neurology.

  12. Kaitseväelastel pole alust kogu missiooni eest lisapalka nõuda / Holger Roonemaa

    Index Scriptorium Estoniae

    Roonemaa, Holger

    2007-01-01

    Afganistanis teeninud kolm Eesti kaitseväelast nõuavad kaitseväelt Tallinna halduskohtus igaüks enam kui poolt miljonit krooni. Tööõigusbüroo Labour Consulting juristi Katrin Sarapi sõnul pole selliseks nõudeks alust. Vt. samas: Rahanõudjad teenivad edasi

  13. Influence of the density pole on the performances of its gamma ...

    African Journals Online (AJOL)

    In this paper, we aim at highlighting the in uence of the density pole on the performances of its gamma-kernel estimator. To do this, we performed a comparative study for the performances of the gamma-kernel estimators with those provided by other bias effect correction techniques at the bounds, using the simulation ...

  14. Weak regularizability and pole assignment for non-square linear systems

    Czech Academy of Sciences Publication Activity Database

    Korotka, Tetiana; Loiseau, J. J.; Zagalak, Petr

    2012-01-01

    Roč. 48, č. 6 (2012), s. 1065-1088 ISSN 0023-5954 R&D Projects: GA ČR GAP103/12/2431 Keywords : linear systems * linear state feedback * pole assignment Subject RIV: BC - Control Systems Theory Impact factor: 0.619, year: 2012 http://library.utia.cas.cz/separaty/2013/AS/korotka-0386325.pdf

  15. Robust pole placement for second-order systems: an LMI approach

    Czech Academy of Sciences Publication Activity Database

    Henrion, D.; Šebek, Michael; Kučera, Vladimír

    2005-01-01

    Roč. 41, č. 1 (2005), s. 1-14 ISSN 0023-5954 R&D Projects: GA ČR GA102/02/0709 Institutional research plan: CEZ:AV0Z10750506 Keywords : polynomial matrix * second-order linear systems * LMI * pole placement * robust control Subject RIV: BC - Control Systems Theory Impact factor: 0.343, year: 2005

  16. Electrical power line and pole removal radiological survey completion report: Revision 2

    International Nuclear Information System (INIS)

    1989-02-01

    Each electric power pole and all wire, cross members, and attached hardware were radiologically surveyed and removed. The survey procedures did not conform in every respect with the planned procedures because the actual work differed from the removal plan. The survey showed that all contamination was fixed. Certain poles that were suspected of being contaminated with Th-230 were cut off one foot above ground level and left on site. Each truck load of materials was checked at the access point to ensure it met release criteria. Wood samples were taken from all the poles at Building 403 and 5% of all the rest and analyzed for U-238 and Th-232. Only U-238 was detected. 1903 bundles of wire (95,150 lin ft) were released, and 76 bundles (1520 lin ft) were found to be contaminated. 7163 lin ft of power pole material were released, and 1484 lin ft were contaminated. A comprehensive quality measure assurance/quality control program was applied to this work

  17. Spontaneous Temporal Pole Encephalocele Presenting with Epilepsy: Report of Two Cases.

    Science.gov (United States)

    Shimada, Seijiro; Kunii, Naoto; Kawai, Kensuke; Usami, Kenichi; Matsuo, Takeshi; Uno, Takeshi; Koizumi, Tomoyuki; Saito, Nobuhito

    2015-09-01

    Refractory temporal lobe epilepsy due to spontaneous temporal pole encephalocele is a rare but increasingly recognized condition. Optimal surgical management is complicated by the lack of knowledge regarding both the extent of the epileptogenic area and the need for repair of the encephalocele. We report two cases that add significant information to these issues. In Case 1, with a 5-year history of refractory seizures, implantation of diagnostic subdural electrodes into the anterior temporal base happened to abolish the seizures completely. No structural changes were evident on postoperative magnetic resonance imaging. In Case 2, with a large encephalocele and a 5-year history of refractory seizures, surgical disconnection of the temporal pole successfully abolished seizures without any need for encephalocele repair. These two cases support the view that the epileptogenic area is confined to within the temporal pole for spontaneous temporal pole encephalocele. Temporopolar disconnection represents one surgical option for this entity that achieves seizure cessation without requiring extra repair procedures. Copyright © 2015 Elsevier Inc. All rights reserved.

  18. Metabolic and mechanical involvement of arms and legs in simulated double pole skiing

    DEFF Research Database (Denmark)

    Rud, B; Secher, N H; Nilsson, J

    2014-01-01

    We evaluated arm and leg work rate and metabolism during double pole ergometer skiing. Thermodilution arm and leg blood flow was determined together with the arterial to venous difference for oxygen, while the work rate was assessed in eight male recreational skiers [24 (SD 7) years]. When work r...

  19. Firn Air Isotope and Temperature Measurements from Siple Dome and South Pole, Version 1

    Data.gov (United States)

    National Aeronautics and Space Administration — This data set includes d15N, d18O/2, dO2/N2/4, d40Ar/4, d38/Ar/2, d84Kr/48, and d132Xe/96 values for air drawn from the top 15 to 50 m of firn at the South Pole...

  20. Combined mismatch repair and POLE/POLD1 defects explain unresolved suspected Lynch syndrome cancers

    NARCIS (Netherlands)

    Jansen, Anne Ml; van Wezel, Tom; van den Akker, Brendy Ewm; Ventayol Garcia, Marina; Ruano, Dina; Tops, Carli Mj; Wagner, Anja; Letteboer, Tom Gw; Gómez-García, Encarna B; Devilee, Peter; Wijnen, Juul T; Hes, Frederik J; Morreau, Hans

    Many suspected Lynch Syndrome (sLS) patients who lack mismatch repair (MMR) germline gene variants and MLH1 or MSH2 hypermethylation are currently explained by somatic MMR gene variants or, occasionally, by germline POLE variants. To further investigate unexplained sLS patients, we analyzed