WorldWideScience

Sample records for polar platform program

  1. Polarization Diversity DPSK Demodulator on the Silicon-on-Insulator Platform with Simple Fabrication

    DEFF Research Database (Denmark)

    Ding, Yunhong; Huang, Bo; Ou, Haiyan

    2013-01-01

    We demonstrate a novel polarization diversity DPSK demodulator on the SOI platform with low polarization dependent loss (1.6 dB) and low polarization dependent extinction ratio (<3 dB). System experiments verify the low polarization dependency....

  2. Space optical instrumentation for earth observation - The polar platform era

    Science.gov (United States)

    Peraldi, Armand

    1988-01-01

    Consideration is given to two instruments for earth observation from large polar platforms: a Thermal IR Imager (TIRI) and a High Resolution Imaging Spectrometer (HRIS). TIRI is an optical push-broom imager designed for operation in the 8-12 micron band, split into two spectral bands. Because each line of an image is electronically scanned by linear arrays of detectors, TIRI does not require a mechanical scanning device. HRIS is designed to provide very high resolution images from 260 spectral channels. Any set of 30 individual channels may be transmitted to the ground. These two instruments are described and illustrated and the possible applications of the instruments on a polar platform are discussed.

  3. Towards Polarization Diversity on the SOI Platform With Simple Fabrication Process

    DEFF Research Database (Denmark)

    Ding, Yunhong; Liu, Liu; Peucheret, Christophe

    2011-01-01

    We present a polarization diversity circuit built on the silicon-on-insulator (SOI) platform, which can be fabricated by a simple process. The polarization diversity is based on two identical air-clad asymmetrical directional couplers, which simultaneously play the roles of polarization splitter...

  4. Polarization diversity DPSK demodulator on the silicon-on-insulator platform with simple fabrication

    DEFF Research Database (Denmark)

    Ding, Yunhong; Huang, Bo; Ou, Haiyan

    2013-01-01

    We demonstrate a novel polarization diversity differential phase-shift keying (DPSK) demodulator on the SOI platform, which is fabricated in a single lithography and etching step. The polarization diversity DPSK demodulator is based on a novel polarization splitter and rotator, which consists...

  5. Biomass Program 2007 Program Peer Review - Thermochemical Conversion Platform Summary

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2009-10-27

    This document discloses the comments provided by a review panel at the U.S. Department of Energy Office of the Biomass Program Peer Review held on November 15-16, 2007 in Baltimore, MD and the Biomass Program Peer Review for the Thermochemical Platform, held on July 9th and 10th in Golden, Colorado.

  6. Platform for Manipulating Polarization Modes Realized with Jones Vectors in MATHEMATICA

    Directory of Open Access Journals (Sweden)

    Yong-Dae Choi

    2015-06-01

    Full Text Available The fundamental conception in physics of the propagation of the electromagnetic wave polarization in matter is newly understood as the cardinal keyword in free-space quantum communication technology and cosmology in astrophysics. Interactive visualization of the propagation mechanism of polarized electromagnetism in a medium with its helicity has accordingly received attention from scientists exploiting the protocol of quantum key distribution (QKD to guarantee unconditional security in cryptography communication. We have provided a dynamic polarization platform for presenting the polarization modes of a transverse electromagnetic wave, converting the state of polarization through the arrangement of optical elements, using Jones vectors calculations in Methematica. The platform graphically simulates the mechanism of production and propagation of the polarized waves in a medium while satisfying Maxwell's equations.

  7. NASA Airborne Science Program: NASA Stratospheric Platforms

    Science.gov (United States)

    Curry, Robert E.

    2010-01-01

    The National Aeronautics and Space Administration conducts a wide variety of remote sensing projects using several unique aircraft platforms. These vehicles have been selected and modified to provide capabilities that are particularly important for geophysical research, in particular, routine access to very high altitudes, long range, long endurance, precise trajectory control, and the payload capacity to operate multiple, diverse instruments concurrently. While the NASA program has been in operation for over 30 years, new aircraft and technological advances that will expand the capabilities for airborne observation are continually being assessed and implemented. This presentation will review the current state of NASA's science platforms, recent improvements and new missions concepts as well as provide a survey of emerging technologies unmanned aerial vehicles for long duration observations (Global Hawk and Predator). Applications of information technology that allow more efficient use of flight time and the ability to rapidly reconfigure systems for different mission objectives are addressed.

  8. Biomass Program 2007 Program Peer Review - Feedstock Platform Summary

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2009-10-27

    This document discloses the comments provided by a review panel at the U.S. Department of Energy Office of the Biomass Program Peer Review held on November 15-16, 2007 in Baltimore, MD and the Feedstock Platform Portfolio Peer Review held on August 21st through 23rd in Washington D.C.

  9. Research progress of anti-icing/deicing technologies for polar ships and offshore platforms

    Directory of Open Access Journals (Sweden)

    XIE Qiang

    2017-01-01

    Full Text Available The polar regions present adverse circumstances of high humidity and strong air-sea exchange. As such, the surfaces of ships and platforms (oil exploiting and drilling platforms serving in polar regions can easily be frozen by ice accretion, which not only affects the operation of the equipment but also threatens safety. This paper summarizes the status of the anti-icing/deicing technologies of both China and abroad for polar ships and offshore platforms, and introduces the various effects of ice accretion on polar ships and offshore platforms, and the resulting safety impacts. It then reviews existing anti-icing/deicing technologies and methods of both China and abroad, including such active deicing methods as electric heating, infrared heating and ultrasonic guided wave deicing, as well as such passive deicing methods as super hydrophobic coating, sacrificial coating, aqueous lubricating layer coating and low cross-link density (with interfacial slippage coating, summarizes their applicability to polar ships and offshore platforms, and finally discusses their advantages/disadvantages.

  10. AFSC/NMML: Platforms of Opportunity Program (POP): 1950 - present

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Platforms of Opportunity Program (POP) is an opportunistic marine mammal sighting program that dates back to the 1950s and includes over 108,000 sightings....

  11. Integrated Cu-based TM-pass polarizer using CMOS technology platform

    KAUST Repository

    Ng, Tien Khee

    2010-01-01

    A transverse-magnetic-pass (TM-pass) copper (Cu) polarizer is proposed and analyzed using the previously published two-dimensional Method-of-Lines beam-propagation model. The proposed polarizer exhibits a simulated high-pass filter characteristics, with TM0 and TE0 mode transmissivity of >70% and <5%, respectively, in the wavelength regime of 1.2-1.6 μm. The polarization extinction ratio (PER) given by 10 log10 (PTM0)/(PTE0) is +11.5 dB across the high-pass wavelength regime. To the best of the authors\\' knowledge, we report here the smallest footprint CMOS-platform compatible TM-polarizer.

  12. Ultrashort hybrid plasmonic transverse electric pass polarizer for silicon-on-insulator platform

    Science.gov (United States)

    Hameed, Mohamed Farhat O.; Zaghloul, Reham; Azzam, Shaimaa I.; Obayya, Salah S. A.

    2017-01-01

    A design of a transverse electric (TE)-pass polarizer based on hybrid plasmonic silicon-on-insulator (SOI) platform is reported and analyzed using full vectorial finite element method. The proposed design has gold nanorods that are injected into the silicon dioxide substrate to tolerate the function of the device, and hence the required polarizing state can be obtained. Detailed design principle is presented, taking advantage of the distinct confinements of the TE and transverse magnetic modes in the core region and their coupling with the surface plasmon modes around the metallic nanorods. According to the positions of the gold nanorods, the suggested plasmonic SOI can be used as a TE-pass polarizer with a compact device length of 1.85 μm with 0.1639 dB insertion losses and extinction ratio of 14.58 dB at wavelength of 1.55 μm. The optimized geometrical parameters offer 3 orders of magnitude smaller than similar devices previously demonstrated on the SOI platform. The proposed design has advantages in terms of simplicity and compactness, which makes it a good candidate to be used in integrated silicon photonics. Further, the compact device size and good performance could provide a simple yet satisfactory solution to the polarization-dependent performance drawback of the silicon photonics devices on the SOI platform.

  13. 2011 Biomass Program Platform Peer Review. Infrastructure

    Energy Technology Data Exchange (ETDEWEB)

    Lindauer, Alicia [Office of Energy Efficiency and Renewable Energy (EERE), Washington, DC (United States)

    2012-02-01

    This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the 2011 U.S. Department of Energy Biomass Program’s Infrastructure Platform Review meeting.

  14. 2011 Biomass Program Platform Peer Review. Sustainability

    Energy Technology Data Exchange (ETDEWEB)

    Eng, Alison Goss [Office of Energy Efficiency and Renewable Energy (EERE), Washington, DC (United States)

    2012-02-01

    This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the 2011 U.S. Department of Energy Biomass Program’s Sustainability Platform Review meeting.

  15. 2011 Biomass Program Platform Peer Review: Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Haq, Zia [Office of Energy Efficiency and Renewable Energy (EERE), Washington, DC (United States)

    2012-02-01

    This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the 2011 U.S. Department of Energy Biomass Program’s Analysis Platform Review meeting.

  16. 2011 Biomass Program Platform Peer Review: Algae

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Joyce [Office of Energy Efficiency and Renewable Energy (EERE), Washington, DC (United States)

    2012-02-01

    This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the 2011 U.S. Department of Energy Biomass Program’s Algae Platform Review meeting.

  17. 2011 Biomass Program Platform Peer Review: Feedstock

    Energy Technology Data Exchange (ETDEWEB)

    McCann, Laura [Office of Energy Efficiency and Renewable Energy (EERE), Washington, DC (United States)

    2012-02-01

    This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the 2011 U.S. Department of Energy Biomass Program’s Feedstock Platform Review meeting.

  18. Identifying potential programs and platforms to deliver multiple micronutrient interventions.

    Science.gov (United States)

    Olney, Deanna K; Rawat, Rahul; Ruel, Marie T

    2012-01-01

    This article reviews the potential of four broad types of platforms, health, agriculture, market-based, and social protection programs, to deliver multiple micronutrient (MMN) interventions (supplementation, fortification, and dietary modification). We assessed the platforms' potential based on seven performance criteria related to programs within these platforms: 1) targeting, 2) efficacy of interventions, 3) quality of implementation, 4) utilization, 5) impact, 6) coverage, and 7) sustainability. We highlight one type of program per platform to illustrate strengths and weaknesses for delivering MMN interventions, identify critical knowledge gaps, and highlight what is needed to increase effectiveness for delivering MMN interventions. We found that all four platforms have the potential to effectively deliver MMN interventions if the following key program elements are addressed: 1) strong behavior change communication strategies to increase demand and proper utilization of services/products; 2) supply side interventions to ensure consistent availability of high quality interventions, products, and well-trained staff; 3) rigorous evaluations of effectiveness, quality of delivery, and impact pathways to generate best practices for replication and scale-up; and 4) timely dissemination of evaluation results to ensure use by program implementers and policy makers. The diversification of delivery platforms, which simultaneously addresses multiple determinants of MMN deficiencies and expands coverage, is needed to accelerate progress in reducing MMN deficiencies.

  19. The BNL polarized H- ion source development program

    International Nuclear Information System (INIS)

    Kponou, A.; Alessi, J.; Hershcovitch, A.; DeVito, B.

    1992-01-01

    Polarized protons have been available for acceleration in the AGS for the high energy physics program since 1984. The polarized H - source, PONI-1, has routinely supplied a 0.4 Hz, 400 μsec pulse having a nominal intensity of 40 μA. Polarization is ∼80% out of the ion source. After PONI- 1 became operational, a program was initiated to develop a more intense source based on a cold ground state atomic beam source, followed by ionization of the polarized H degrees beam by D - charge exchange. Various phases of this work have been fully reported elsewhere, and only a summary is given here

  20. PolarTREC—A Model Program for Taking Polar Literacy into the Future

    Science.gov (United States)

    Warburton, J.; Timm, K.; Larson, A. M.

    2009-12-01

    Polar TREC—Teachers and Researchers Exploring and Collaborating, is a three-year (2007-2009) NSF-funded International Polar Year (IPY) teacher professional development program that advances Science, Technology, Engineering, and Mathematics (STEM) education by improving teacher content knowledge and instructional practices through Teacher Research Experiences (TRE) in the Arctic and Antarctic. Leveraging profound changes and fascinating science taking place in the polar regions, PolarTREC broadly disseminates activities and products to students, educators, researchers, and the public, connecting them with the Arctic and Antarctica and sustaining the widespread interest in the polar regions and building on the enthusiasm that was generated through IPY. Central to the PolarTREC Teacher Research Experience Model, over 40 teachers have spent two to eight weeks participating in hands-on research in the polar regions and sharing their experiences with diverse audiences via live events, online multimedia journals, and interactive bulletin boards. The Connecting Arctic/Antarctic Researchers and Educators (CARE) Network unifies learning community members participants, alumni, and others, developing a sustainable association of education professionals networking to share and apply polar STEM content and pedagogical skills. Educator and student feedback from preliminary results of the program evaluation has shown that PolarTREC’s comprehensive program activities have many positive impacts on educators and their ability to teach science concepts and improve their teaching methods. Additionally, K-12 students polled in interest surveys showed significant changes in key areas including amount of time spent in school exploring research activities, importance of understanding science for future work, importance of understanding the polar regions as a person in today’s world, as well as increased self-reported knowledge and interest in numerous science content areas. Building

  1. The UNH polarized 3He program

    International Nuclear Information System (INIS)

    Hersman, F. W.; Carrier, R. H.; Pomeroy, V. R.

    1998-01-01

    The UNH Nuclear Physics Group is developing polarized 3 He cells for use in approved experiments with electron beams and neutron beams. We also have begun to apply our expertise to magnetic resonance imaging experiments I list our projects and review several areas where we have been focusing our efforts

  2. Advancing nano-satellite platforms : The Delfi Program

    NARCIS (Netherlands)

    Bouwmeester, J.; Gill, E.K.A.; Verhoeven, C.J.M.

    2008-01-01

    The Delfi Program aims to launch a nano-satellite every 2.5 years with the objectives to give the best education for space engineering, to test and qualify novel space technology and to enhance the nanosatellite platform to open doors for new applications. With Delfi-C3 in orbit, Delfi-n3Xt in

  3. Biomass Program 2007 Peer Review - Integrated Biorefinery Platform Summary

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2009-10-27

    This document discloses the comments provided by a review panel at the U.S. Department of Energy Office of the Biomass Program Peer Review held on November 15-16, 2007 in Baltimore, MD and the Integrated Biorefinery Platform Review held on August 13-15, 2007 in Golden, Colorado.

  4. USING THE GOOGLE APP ENGINE PLATFORM FOR TEACHING PROGRAMMING

    Directory of Open Access Journals (Sweden)

    Mariusz Dzieńkowski

    2012-12-01

    Full Text Available The article outlines the present situation connected with teaching programming to students of different levels of education in Polish schools. The observed negative trend towards marginalization of programming can be successfully reversed in education thanks to using the latest IT achievements such as cloud computing (CC. The paper presents ways in which the cloud computing technology can be used to teach how to develop and code Internet applications by means of the Google App Engine platform. The final part focuses on practical examples of programming problems involving cloud computing applications which may be solved in IT classes with students of different levels of education.

  5. Integration of the TNXYZ computer program inside the platform Salome

    International Nuclear Information System (INIS)

    Chaparro V, F. J.

    2014-01-01

    The present work shows the procedure carried out to integrate the code TNXYZ as a calculation tool at the graphical simulation platform Salome. The TNXYZ code propose a numerical solution of the neutron transport equation, in several groups of energy, steady-state and three-dimensional geometry. In order to discretized the variables of the transport equation, the code uses the method of discrete ordinates for the angular variable, and a nodal method for the spatial dependence. The Salome platform is a graphical environment designed for building, editing and simulating mechanical models mainly focused on the industry and unlike other software, in order to form a complete scheme of pre and post processing of information, to integrate and control an external source code. Before the integration the in the Salome platform TNXYZ code was upgraded. TNXYZ was programmed in the 90s using Fortran 77 compiler; for this reason the code was adapted to the characteristics of the current Fortran compilers; in addition, with the intention of extracting partial results over the process sequence, the original structure of the program underwent a modularization process, i.e. the main program was divided into sections where the code performs major operations. This procedure is controlled by the information module (YACS) on Salome platform, and it could be useful for a subsequent coupling with thermal-hydraulics codes. Finally, with the help of the Monte Carlo code Serpent several study cases were defined in order to check the process of integration; the verification process consisted in performing a comparison of the results obtained with the code executed as stand-alone and after modernized, integrated and controlled by the Salome platform. (Author)

  6. NMRFx Processor: a cross-platform NMR data processing program

    International Nuclear Information System (INIS)

    Norris, Michael; Fetler, Bayard; Marchant, Jan; Johnson, Bruce A.

    2016-01-01

    NMRFx Processor is a new program for the processing of NMR data. Written in the Java programming language, NMRFx Processor is a cross-platform application and runs on Linux, Mac OS X and Windows operating systems. The application can be run in both a graphical user interface (GUI) mode and from the command line. Processing scripts are written in the Python programming language and executed so that the low-level Java commands are automatically run in parallel on computers with multiple cores or CPUs. Processing scripts can be generated automatically from the parameters of NMR experiments or interactively constructed in the GUI. A wide variety of processing operations are provided, including methods for processing of non-uniformly sampled datasets using iterative soft thresholding. The interactive GUI also enables the use of the program as an educational tool for teaching basic and advanced techniques in NMR data analysis.

  7. NMRFx Processor: a cross-platform NMR data processing program.

    Science.gov (United States)

    Norris, Michael; Fetler, Bayard; Marchant, Jan; Johnson, Bruce A

    2016-08-01

    NMRFx Processor is a new program for the processing of NMR data. Written in the Java programming language, NMRFx Processor is a cross-platform application and runs on Linux, Mac OS X and Windows operating systems. The application can be run in both a graphical user interface (GUI) mode and from the command line. Processing scripts are written in the Python programming language and executed so that the low-level Java commands are automatically run in parallel on computers with multiple cores or CPUs. Processing scripts can be generated automatically from the parameters of NMR experiments or interactively constructed in the GUI. A wide variety of processing operations are provided, including methods for processing of non-uniformly sampled datasets using iterative soft thresholding. The interactive GUI also enables the use of the program as an educational tool for teaching basic and advanced techniques in NMR data analysis.

  8. NMRFx Processor: a cross-platform NMR data processing program

    Energy Technology Data Exchange (ETDEWEB)

    Norris, Michael; Fetler, Bayard [One Moon Scientific, Inc. (United States); Marchant, Jan [University of Maryland Baltimore County, Howard Hughes Medical Institute (United States); Johnson, Bruce A., E-mail: bruce.johnson@asrc.cuny.edu [One Moon Scientific, Inc. (United States)

    2016-08-15

    NMRFx Processor is a new program for the processing of NMR data. Written in the Java programming language, NMRFx Processor is a cross-platform application and runs on Linux, Mac OS X and Windows operating systems. The application can be run in both a graphical user interface (GUI) mode and from the command line. Processing scripts are written in the Python programming language and executed so that the low-level Java commands are automatically run in parallel on computers with multiple cores or CPUs. Processing scripts can be generated automatically from the parameters of NMR experiments or interactively constructed in the GUI. A wide variety of processing operations are provided, including methods for processing of non-uniformly sampled datasets using iterative soft thresholding. The interactive GUI also enables the use of the program as an educational tool for teaching basic and advanced techniques in NMR data analysis.

  9. A remote care platform for the social support program CASSAUDEC

    Directory of Open Access Journals (Sweden)

    Andrés Felipe Ardila Rodríguez

    2016-06-01

    Full Text Available The training strategies developed for the social support program bring deficits in accessibility to the chronic ill patients (EC and the CASSA-UDEC’s caretaker (CASSA-UDEC: Centre for Social Health Care at Universidad de Cundinamarca they do not have time to commute, hindering their legal relationship established by the contract. For this reason, a remote care platform (PTD was developed to support users at CASSA-UDEC improving aspects related to coverage, cost, quality, access and appropriation of information from caregivers and chronic ill patients. The design was based on gerontological constructs identifying features such as modularity, object size, usability, ergonomics, and some others, providing a friendly platform for the user with dynamic, modular and high usability content. The Platform provides a space for interaction and aid, which works as a dynamic entity in the job done by CASSA-UDEC giving support in the development of activities, expanding its coverage, access; all thanks to the benefits offered in a virtual mode.

  10. GeoMapApp as a platform for visualizing marine data from Polar Regions

    Science.gov (United States)

    Nitsche, F. O.; Ryan, W. B.; Carbotte, S. M.; Ferrini, V.; Goodwillie, A. M.; O'hara, S. H.; Weissel, R.; McLain, K.; Chinhong, C.; Arko, R. A.; Chan, S.; Morton, J. J.; Pomeroy, D.

    2012-12-01

    To maximize the investment in expensive fieldwork the resulting data should be re-used as much as possible. In addition, unnecessary duplication of data collection effort should be avoided. This becomes even more important if access to field areas is as difficult and expensive as it is in Polar Regions. Making existing data discoverable in an easy to use platform is key to improve re-use and avoid duplication. A common obstacle is that use of existing data is often limited to specialists who know of the data existence and also have the right tools to view and analyze these data. GeoMapApp is a free, interactive, map based tool that allows users to discover, visualize, and analyze a large number of data sets. In addition to a global view, it provides polar map projections for displaying data in Arctic and Antarctic areas. Data that have currently been added to the system include Arctic swath bathymetry data collected from the USCG icebreaker Healy. These data are collected almost continuously including from cruises where bathymetry is not the main objective and for which existence of the acquired data may not be well known. In contrast, existence of seismic data from the Antarctic continental margin is well known in the seismic community. They are archived at and can be accessed through the Antarctic Seismic Data Library System (SDLS). Incorporating these data into GeoMapApp makes an even broader community aware of these data and the custom interface, which includes capabilities to visualize and explore these data, allows users without specific software or knowledge of the underlying data format to access the data. In addition to investigating these datasets, GeoMapApp provides links to the actual data sources to allow specialists the opportunity to re-use the original data. Important identification of data sources and data references are achieved on different levels. For access to the actual Antarctic seismic data GeoMapApp links to the SDLS site, where users have

  11. Integration of the program TNXYZ in the platform SALOME

    International Nuclear Information System (INIS)

    Chaparro V, F. J.; Silva A, L.; Del Valle G, E.; Gomez T, A. M.; Vargas E, S.

    2013-10-01

    This work presents the procedure realized to integrate the code TNXYZ like a processing tool to the graphic simulation platform SALOME. The code TNXYZ solves the neutron transport equation in stationary state, for several energy groups, quantizing the angular variable by the discrete ordinates method and the space variable by nodal methods. The platform SALOME is a graphic surrounding designed for the construction, edition and simulation of mechanical models focused to the industry and contrary to other software, it allows to integrate external source codes to the surrounding, to form a complete scheme of execution, supervision, pre and post information processing. The code TNXYZ was programmed in the 90s in a Fortran compiler, but to be used at the present time the code should be actualized to the current compiler characteristics; also, in the original scheme was carried out a modularization process, that is to say, the main program was divided in sections where the code carries out important operations, with the intention of flexibility the data extraction process along its processing sequence and that can be useful in a later development of coupling. Finally, to verify the integration a fuel assembly BWR was modeled, as well as a control cell. The cross sections were obtained with the Monte Carlo Serpent code. Some results obtained with Serpent were used to verify and to begin with the validation of the code, being obtained an acceptable comparison in the infinite multiplication factor. The validation process should extend and one has planned to present in a future work. This work is part of the development of the research group formed between the Escuela Superior de Fisica y Matematicas del Instituto Politecnico Nacional (IPN) and the Instituto Nacional de Investigaciones Nucleares (ININ) in which a simulation Mexican platform of nuclear reactors is developed. (Author)

  12. Polarized proton acceleration program at the AGS and RHIC

    International Nuclear Information System (INIS)

    Lee, Y.Y.

    1995-01-01

    Presented is an overview of the program for acceleration of polarized protons in the AGS and their injection into the RHIC collider. The problem of depolarizing resonances in strong focusing circulator accelerators is discussed. The intrinsic resonances are jumped over by the fast tune jump, and a partial Siberian Snake is used to compensate for over forty imperfection resonances in the AGS. Two sets of full Siberian Snake and spin rotators will be employed in RHIC

  13. United States Naval Academy Polar Science Program; Undergraduate Research and Outreach in Polar Environments

    Science.gov (United States)

    Woods, J. E.

    2013-12-01

    The United States Naval Academy (USNA) Polar Science Program (PSP), has been very active completing its own field campaign out of Barrow, AK, sent students to the South Pole, participated in STEM activities and educated over 100 future Naval Officers about the Polar Regions. Each activity is uniquely different, but has the similar undertone of sharing the recent rapid changes in the Cryosphere to a wide range of audiences. There is further room for development and growth through future field campaigns and new collaborations. The Naval Academy Ice Experiment (NAICEX) 2013 was based out of the old Naval Arctic Research Laboratory (NARL) in Barrow, AK. In joint collaboration with the University of Delaware, University of Washington, and Naval Research Laboratory we successfully took multiple measurements for over a week on the fast ice just offshore. Five undergraduate students from USNA, as well as 3 graduate students from University of Delaware participated, as well as multiple professors and instructors from each institution. Data collected during the experiment will be used in capstone courses and thesis research. There was also an outreach component to the experiment, where local students from Barrow H.S. have been assigned to the USNA ice observations project for their own high school course work. Local students will be analyzing data that will contribute into the larger research effort at USNA through coordinated remote efforts and participation in future field experiments. The USNA STEM office is one of the most robust in the entire country. The USNA PSP is active within this program by developing polar specific modules that are integrated varying length outreach opportunities from a few hours to week long camps. USNA PSP also engages in educator training that is held at the Naval Academy each summer. Through this program of educating the educators, the far reaching levels of awareness are multiplied exponentially. Also, the USNA Oceanography Department has

  14. Biomass Program 2007 Program Peer Review - Biochemical and Products Platform Summary

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2009-10-27

    This document discloses the comments provided by a review panel at the U.S. Department of Energy Office of the Biomass Program Peer Review held on November 15-16, 2007 in Baltimore, MD and the Biochemical and Products Platform Review held on August 7-9, 2007 in Denver, Colorado.

  15. 30 CFR 250.910 - Which of my facilities are subject to the Platform Verification Program?

    Science.gov (United States)

    2010-07-01

    ... pipeline risers, and riser tensioning systems (each platform must be designed to accommodate all the loads... Platform Verification Program: (i) Drilling, production, and pipeline risers, and riser tensioning systems... new purpose, or making a major modification of, or major repair to, that platform, is also subject to...

  16. Task Characterisation and Cross-Platform Programming Through System Identification

    Directory of Open Access Journals (Sweden)

    Theocharis Kyriacou

    2005-12-01

    Full Text Available Developing robust and reliable control code for autonomous mobile robots is difficult, because the interaction between a physical robot and the environment is highly complex, it is subject to noise and variation, and therefore partly unpredictable. This means that to date it is not possible to predict robot behaviour, based on theoretical models. Instead, current methods to develop robot control code still require a substantial trial-and-error component to the software design process. Such iterative refinement could be reduced, we argue, if a more profound theoretical understanding of robot-environment interaction existed. In this paper, we therefore present a modelling method that generates a faithful model of a robot's interaction with its environment, based on data logged while observing a physical robot's behaviour. Because this modelling method — nonlinear modelling using polynomials — is commonly used in the engineering discipline of system identification, we refer to it here as “robot identification”. We show in this paper that using robot identification to obtain a computer model of robot-environment interaction offers several distinct advantages: Very compact representations (one-line programs of the robot control program are generated The model can be analysed, for example through sensitivity analysis, leading to a better understanding of the essential parameters underlying the robot's behaviour, and The generated, compact robot code can be used for cross-platform robot programming, allowing fast transfer of robot code from one type of robot to another. We demonstrate these points through experiments with a Magellan Pro and a Nomad 200 mobile robot.

  17. Task Characterisation and Cross-Platform Programming Through System Identification

    Directory of Open Access Journals (Sweden)

    Roberto Iglesias

    2008-11-01

    Full Text Available Developing robust and reliable control code for autonomous mobile robots is difficult, because the interaction between a physical robot and the environment is highly complex, it is subject to noise and variation, and therefore partly unpredictable. This means that to date it is not possible to predict robot behaviour, based on theoretical models. Instead, current methods to develop robot control code still require a substantial trial-and-error component to the software design process. Such iterative refinement could be reduced, we argue, if a more profound theoretical understanding of robot-environment interaction existed. In this paper, we therefore present a modelling method that generates a faithful model of a robot's interaction with its environment, based on data logged while observing a physical robot's behaviour. Because this modelling method - nonlinear modelling using polynomials - is commonly used in the engineering discipline of system identification, we refer to it here as "robot identification". We show in this paper that using robot identification to obtain a computer model of robot environment interaction offers several distinct advantages:
    1. Very compact representations (one-line programs of the robot control program are generated
    2.The model can be analysed, for example through sensitivity analysis, leading to a better understanding of the essential parameters underlying the robot's behaviour, and
    3. The generated, compact robot code can be used for cross-platform robot programming, allowing fast transfer of robot code from one type of robot to another.
    We demonstrate these points through experiments with a Magellan Pro and a Nomad 200 mobile robot.

  18. International Polar Year 2007: An Integrated Heliospheric and Oceanographic Program?

    Science.gov (United States)

    Johnson, G.; Davila, J.

    An international symposium SPerspectives of Modern Polar ResearchT was convened - in Bad Durkeim, Germany 2001 to celebrated the 175the anniversary of the birth of Georg von Neumayer. At that symposium the Nermayer Declaration was adopted to commemorate the 125th anniversary of the IPY in 2007. SA 125th year IPY program be initiated using new and present technologies to determine: 1 . Causes and effects of climatic variability-air/sea/ice interactins, and 2. Lithosphere dynamicsUevolution and history of crust and sedimentary cover. The po lar regions would be the focus.T Polar oceanographic contributions to global climate change are still a matter of conjecture, and to a large extent so are the extraterrestrial contributions. The proposed IPY would focus on these issues. As part of the global heat engine, the polar regions hav a major role in the worldSs transfer of energy, and the ocean/stmosphere system is known to be both an indicator and a componenet of climate change. It is clear that acomplex suite of significant, interrelated, atmospheric, oceanic and terrestrial changes has occurred in the the polsar regions in recent decades. These events are affecting every part of the polar environment and are having repercussions on society. In a similar vein an International Heliophysical Year (IHY) has been proposed to obtain a coordinated set of observations to study at the largest scale the solar genergated events that affect life and climate on Earth as has been documented in the Holocene sedimentary recofd. A modeling capability is the ultimate goal so the physical process can be tracked throughout the entire Sun-Earth system. This program will require an integrated, holistic system approach encompassing a side range of disciplines with new and improved technologies for long term measurements on the seabed, in the water column and in space over all seasons. Coordination, collaboration and documentation of an interated science plan with international scientific

  19. 2011 Biomass Program Platform Peer Review. Thermochemical Conversion

    Energy Technology Data Exchange (ETDEWEB)

    Grabowski, Paul E. [Office of Energy Efficiency and Renewable Energy (EERE), Washington, DC (United States)

    2012-02-01

    This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the 2011 U.S. Department of Energy Biomass Program’s Thermochemical Conversion Platform Review meeting.

  20. 2011 Biomass Program Platform Peer Review. Integrated Biorefineries

    Energy Technology Data Exchange (ETDEWEB)

    Rossmeissl, Neil [Office of Energy Efficiency and Renewable Energy (EERE), Washington, DC (United States)

    2012-02-01

    This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the 2011 U.S. Department of Energy Biomass Program’s IBR Platform Review meeting.

  1. 2011 Biomass Program Platform Peer Review: Biochemical Conversion

    Energy Technology Data Exchange (ETDEWEB)

    Pezzullo, Leslie [Office of Energy Efficiency and Renewable Energy (EERE), Washington, DC (United States)

    2012-02-01

    This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the 2011 U.S. Department of Energy Biomass Program’s Biochemical Conversion Platform Review meeting.

  2. [Reply to “Space Station?” by L.H. Meredith] EOS: The Earth Observing System and polar platforms

    Science.gov (United States)

    Butler, D. M.; Gurney, R. J.; Miller, T. L.

    The statement about the Space Station by L. H. Meredith (Eos, September 29, 1987) did not mention the Polar Platform component of the space station. Insofar as the planned Earth Observing System (EOS) will make extensive use of the Polar Platform, the following description is provided so that more complete information is available to the Eos readership in the invited discussion on the space station. EOS, with participation by the National Aeronautics and Space Administration (NASA), National Oceanic and Atmospheric Administration (NOAA), European Space Agency (ESA), and Japan, is the cornerstone of the Mission to Planet Earth initiative. It will use the Polar Platform for the most massive undertaking in characterizing the Earth system and in studying global change that has ever been attempted. The description here has been abstracted from a NASA report that will soon be available for public distribution: “From Pattern to Process: The Strategy of the Earth Observing System.”

  3. Detecting Canopy Water Status Using Shortwave Infrared Reflectance Data From Polar Orbiting and Geostationary Platforms

    DEFF Research Database (Denmark)

    Fensholt, Rasmus; Huber Gharib, Silvia; Proud, Simon Richard

    2010-01-01

    analyses performed on SEVIRI SIWSI during a dry period within the growing season support these findings. These results suggest that the combined advantage of an improved temporal resolution and a fixed viewing angle potentially makes the SEVIRI sensor an interesting complementary data source to POES data......-based canopy water status detection from geostationary Meteosat Second Generation (MSG) Spinning Enhanced Visible and Infrared Imager (SEVIRI) data as compared to polar orbiting environmental satellite (POES)-based moderate resolution imaging spectroradiometer (MODIS) data. The EO-based SWIR water stress index...

  4. Planetary Balloon-Based Science Platform Evaluation and Program Implementation

    Science.gov (United States)

    Dankanich, John W.; Kremic, Tibor; Hibbitts, Karl; Young, Eliot F.; Landis, Rob

    2016-01-01

    This report describes a study evaluating the potential for a balloon-based optical telescope as a planetary science asset to achieve decadal class science. The study considered potential science achievable and science traceability relative to the most recent planetary science decadal survey, potential platform features, and demonstration flights in the evaluation process. Science Potential and Benefits: This study confirms the cost the-benefit value for planetary science purposes. Forty-four (44) important questions of the decadal survey are at least partially addressable through balloon based capabilities. Planetary science through balloon observations can provide significant science through observations in the 300 nm to 5 m range and at longer wavelengths as well. Additionally, balloon missions have demonstrated the ability to progress from concept to observation to publication much faster than a space mission increasing the speed of science return. Planetary science from a balloon-borne platform is a relatively low-cost approach to new science measurements. This is particularly relevant within a cost-constrained planetary science budget. Repeated flights further reduce the cost of the per unit science data. Such flights offer observing time at a very competitive cost. Another advantage for planetary scientists is that a dedicated asset could provide significant new viewing opportunities not possible from the ground and allow unprecedented access to observations that cannot be realized with the time allocation pressures faced by current observing assets. In addition, flight systems that have a relatively short life cycle and where hardware is generally recovered, are excellent opportunities to train early career scientists, engineers, and project managers. The fact that balloon-borne payloads, unlike space missions, are generally recovered offers an excellent tool to test and mature instruments and other space craft systems. Desired Gondola Features: Potential

  5. Fostering science communication and outreach through video production in Dartmouth's IGERT Polar Environmental Change graduate program

    Science.gov (United States)

    Hammond Wagner, C. R.; McDavid, L. A.; Virginia, R. A.

    2013-12-01

    Dartmouth's NSF-supported IGERT Polar Environmental Change graduate program has focused on using video media to foster interdisciplinary thinking and to improve student skills in science communication and public outreach. Researchers, educators, and funding organizations alike recognize the value of video media for making research results more accessible and relevant to diverse audiences and across cultures. We present an affordable equipment set and the basic video training needed as well as available Dartmouth institutional support systems for students to produce outreach videos on climate change and its associated impacts on people. We highlight and discuss the successes and challenges of producing three types of video products created by graduate and undergraduate students affiliated with the Dartmouth IGERT. The video projects created include 1) graduate student profile videos, 2) a series of short student-created educational videos for Greenlandic high school students, and 3) an outreach video about women in science based on the experiences of women students conducting research during the IGERT field seminar at Summit Station and Kangerlussuaq, Greenland. The 'Science in Greenland--It's a Girl Thing' video was featured on The New York Times Dot Earth blog and the Huffington Post Green blog among others and received international recognition. While producing these videos, students 1) identified an audience and created story lines, 2) worked in front of and behind the camera, 3) utilized low-cost digital editing applications, and 4) shared the videos on multiple platforms from social media to live presentations. The three video projects were designed to reach different audiences, and presented unique challenges for content presentation and dissemination. Based on student and faculty assessment, we conclude that the video projects improved student science communication skills and increased public knowledge of polar science and the effects of climate change.

  6. A Set of Free Cross-Platform Authoring Programs for Flexible Web-Based CALL Exercises

    Science.gov (United States)

    O'Brien, Myles

    2012-01-01

    The Mango Suite is a set of three freely downloadable cross-platform authoring programs for flexible network-based CALL exercises. They are Adobe Air applications, so they can be used on Windows, Macintosh, or Linux computers, provided the freely-available Adobe Air has been installed on the computer. The exercises which the programs generate are…

  7. Development of a polar direct-drive platform for studying inertial confinement fusion implosion mix on the National Ignition Facility

    Energy Technology Data Exchange (ETDEWEB)

    Schmitt, Mark J.; Bradley, Paul A.; Cobble, James A.; Fincke, James R.; Hakel, Peter; Hsu, Scott C.; Krasheninnikova, Natalia S.; Kyrala, George A.; Magelssen, Glenn R.; Montgomery, David S.; Murphy, Thomas J.; Obrey, Kimberly A.; Shah, Rahul C.; Tregillis, Ian L.; Baumgaertel, Jessica A.; Wysocki, Frederick J.; Batha, Steven H. [Los Alamos National Laboratory, MS F699, Los Alamos, New Mexico 87545 (United States); Stephen Craxton, R.; McKenty, Patrick W. [Laboratory for Laser Energetics, University of Rochester, 250 E. River Road, Rochester, New York 14623 (United States); Fitzsimmons, Paul [General Atomics, 3550 General Atomics Court, San Diego, California 92121 (United States); and others

    2013-05-15

    Experiments were performed to develop a platform for the simultaneous measurement of mix and its effects on fusion burn. Two polar direct drive implosions of all-plastic capsules were conducted for the first time on the National Ignition Facility (NIF). To measure implosion trajectory and symmetry, area image backlighting of these capsules was also employed for the first time on NIF, an advance over previous 1-D slit imaging experiments, providing detailed symmetry data of the capsules as they imploded. The implosion trajectory and low-mode asymmetry seen in the resultant radiographs agreed with pre-shot predictions even though the 700 kJ drive energy produced laser beam intensities exceeding laser-plasma instability thresholds. Post-shot simulations indicate that the capsule yield was reduced by a factor of two compared to pre-shot predictions owing to as-shot laser drive asymmetries. The pre-shot predictions of bang time agreed within 200 ps with the experimental results. The second shot incorporated a narrow groove encircling the equator of the capsule. A predicted yield reduction factor of three was not observed.

  8. Development of a polar direct-drive platform for studying inertial confinement fusion implosion mix on the National Ignition Facility

    International Nuclear Information System (INIS)

    Schmitt, Mark J.; Bradley, Paul A.; Cobble, James A.; Fincke, James R.; Hakel, Peter; Hsu, Scott C.; Krasheninnikova, Natalia S.; Kyrala, George A.; Magelssen, Glenn R.; Montgomery, David S.; Murphy, Thomas J.; Obrey, Kimberly A.; Shah, Rahul C.; Tregillis, Ian L.; Baumgaertel, Jessica A.; Wysocki, Frederick J.; Batha, Steven H.; Stephen Craxton, R.; McKenty, Patrick W.; Fitzsimmons, Paul

    2013-01-01

    Experiments were performed to develop a platform for the simultaneous measurement of mix and its effects on fusion burn. Two polar direct drive implosions of all-plastic capsules were conducted for the first time on the National Ignition Facility (NIF). To measure implosion trajectory and symmetry, area image backlighting of these capsules was also employed for the first time on NIF, an advance over previous 1-D slit imaging experiments, providing detailed symmetry data of the capsules as they imploded. The implosion trajectory and low-mode asymmetry seen in the resultant radiographs agreed with pre-shot predictions even though the 700 kJ drive energy produced laser beam intensities exceeding laser-plasma instability thresholds. Post-shot simulations indicate that the capsule yield was reduced by a factor of two compared to pre-shot predictions owing to as-shot laser drive asymmetries. The pre-shot predictions of bang time agreed within 200 ps with the experimental results. The second shot incorporated a narrow groove encircling the equator of the capsule. A predicted yield reduction factor of three was not observed

  9. The Jasper Framework: Towards a Platform Independent, Formal Treatment of Web Programming

    Directory of Open Access Journals (Sweden)

    James Smith

    2012-10-01

    Full Text Available This paper introduces Jasper, a web programming framework which allows web applications to be developed in an essentially platform indepedent manner and which is also suited to a formal treatment. It outlines Jasper conceptually and shows how Jasper is implemented on several commonplace platforms. It also introduces the Jasper Music Store, a web application powered by Jasper and implemented on each of these platforms. And it briefly describes a formal treatment and outlines the tools and languages planned that will allow this treatment to be automated.

  10. Evolutionary programming as a platform for in silico metabolic engineering

    DEFF Research Database (Denmark)

    Patil, Kiran Raosaheb; Rocha, Isabel; Förster, Jochen

    2005-01-01

    , it is often difficult to predict the effects of genetic modifications on the resulting phenotype. Recently genome-scale metabolic models have been compiled for several different microorganisms where structural and stoichiometric complexity is inherently accounted for. New algorithms are being developed......, and it is therefore interesting to develop new faster algorithms. Results In this study we report an evolutionary programming based method to rapidly identify gene deletion strategies for optimization of a desired phenotypic objective function. We illustrate the proposed method for two important design parameters...... are discussed. Conclusion We show that evolutionary programming enables solving large gene knockout problems in relatively short computational time. The proposed algorithm also allows the optimization of non-linear objective functions or incorporation of non-linear constraints and additionally provides a family...

  11. Evolutionary programming as a platform for in silico metabolic engineering

    Directory of Open Access Journals (Sweden)

    Förster Jochen

    2005-12-01

    Full Text Available Abstract Background Through genetic engineering it is possible to introduce targeted genetic changes and hereby engineer the metabolism of microbial cells with the objective to obtain desirable phenotypes. However, owing to the complexity of metabolic networks, both in terms of structure and regulation, it is often difficult to predict the effects of genetic modifications on the resulting phenotype. Recently genome-scale metabolic models have been compiled for several different microorganisms where structural and stoichiometric complexity is inherently accounted for. New algorithms are being developed by using genome-scale metabolic models that enable identification of gene knockout strategies for obtaining improved phenotypes. However, the problem of finding optimal gene deletion strategy is combinatorial and consequently the computational time increases exponentially with the size of the problem, and it is therefore interesting to develop new faster algorithms. Results In this study we report an evolutionary programming based method to rapidly identify gene deletion strategies for optimization of a desired phenotypic objective function. We illustrate the proposed method for two important design parameters in industrial fermentations, one linear and other non-linear, by using a genome-scale model of the yeast Saccharomyces cerevisiae. Potential metabolic engineering targets for improved production of succinic acid, glycerol and vanillin are identified and underlying flux changes for the predicted mutants are discussed. Conclusion We show that evolutionary programming enables solving large gene knockout problems in relatively short computational time. The proposed algorithm also allows the optimization of non-linear objective functions or incorporation of non-linear constraints and additionally provides a family of close to optimal solutions. The identified metabolic engineering strategies suggest that non-intuitive genetic modifications span

  12. Evolutionary programming as a platform for in silico metabolic engineering

    Science.gov (United States)

    Patil, Kiran Raosaheb; Rocha, Isabel; Förster, Jochen; Nielsen, Jens

    2005-01-01

    Background Through genetic engineering it is possible to introduce targeted genetic changes and hereby engineer the metabolism of microbial cells with the objective to obtain desirable phenotypes. However, owing to the complexity of metabolic networks, both in terms of structure and regulation, it is often difficult to predict the effects of genetic modifications on the resulting phenotype. Recently genome-scale metabolic models have been compiled for several different microorganisms where structural and stoichiometric complexity is inherently accounted for. New algorithms are being developed by using genome-scale metabolic models that enable identification of gene knockout strategies for obtaining improved phenotypes. However, the problem of finding optimal gene deletion strategy is combinatorial and consequently the computational time increases exponentially with the size of the problem, and it is therefore interesting to develop new faster algorithms. Results In this study we report an evolutionary programming based method to rapidly identify gene deletion strategies for optimization of a desired phenotypic objective function. We illustrate the proposed method for two important design parameters in industrial fermentations, one linear and other non-linear, by using a genome-scale model of the yeast Saccharomyces cerevisiae. Potential metabolic engineering targets for improved production of succinic acid, glycerol and vanillin are identified and underlying flux changes for the predicted mutants are discussed. Conclusion We show that evolutionary programming enables solving large gene knockout problems in relatively short computational time. The proposed algorithm also allows the optimization of non-linear objective functions or incorporation of non-linear constraints and additionally provides a family of close to optimal solutions. The identified metabolic engineering strategies suggest that non-intuitive genetic modifications span several different pathways and

  13. Evolutionary programming as a platform for in silico metabolic engineering.

    Science.gov (United States)

    Patil, Kiran Raosaheb; Rocha, Isabel; Förster, Jochen; Nielsen, Jens

    2005-12-23

    Through genetic engineering it is possible to introduce targeted genetic changes and hereby engineer the metabolism of microbial cells with the objective to obtain desirable phenotypes. However, owing to the complexity of metabolic networks, both in terms of structure and regulation, it is often difficult to predict the effects of genetic modifications on the resulting phenotype. Recently genome-scale metabolic models have been compiled for several different microorganisms where structural and stoichiometric complexity is inherently accounted for. New algorithms are being developed by using genome-scale metabolic models that enable identification of gene knockout strategies for obtaining improved phenotypes. However, the problem of finding optimal gene deletion strategy is combinatorial and consequently the computational time increases exponentially with the size of the problem, and it is therefore interesting to develop new faster algorithms. In this study we report an evolutionary programming based method to rapidly identify gene deletion strategies for optimization of a desired phenotypic objective function. We illustrate the proposed method for two important design parameters in industrial fermentations, one linear and other non-linear, by using a genome-scale model of the yeast Saccharomyces cerevisiae. Potential metabolic engineering targets for improved production of succinic acid, glycerol and vanillin are identified and underlying flux changes for the predicted mutants are discussed. We show that evolutionary programming enables solving large gene knockout problems in relatively short computational time. The proposed algorithm also allows the optimization of non-linear objective functions or incorporation of non-linear constraints and additionally provides a family of close to optimal solutions. The identified metabolic engineering strategies suggest that non-intuitive genetic modifications span several different pathways and may be necessary for solving

  14. Encapsulating Software Platform Logic by Aspect-Oriented Programming : A Case Study in Using Aspects for Language Portability

    NARCIS (Netherlands)

    Kats, L.C.; Visser, E.

    2010-01-01

    Software platforms such as the Java Virtual Machine or the CLR .NET virtual machine have their own ecosystem of a core programming language or instruction set, libraries, and developer community. Programming languages can target multiple software platforms to increase interoperability or to boost

  15. Cloudgene: a graphical execution platform for MapReduce programs on private and public clouds.

    Science.gov (United States)

    Schönherr, Sebastian; Forer, Lukas; Weißensteiner, Hansi; Kronenberg, Florian; Specht, Günther; Kloss-Brandstätter, Anita

    2012-08-13

    The MapReduce framework enables a scalable processing and analyzing of large datasets by distributing the computational load on connected computer nodes, referred to as a cluster. In Bioinformatics, MapReduce has already been adopted to various case scenarios such as mapping next generation sequencing data to a reference genome, finding SNPs from short read data or matching strings in genotype files. Nevertheless, tasks like installing and maintaining MapReduce on a cluster system, importing data into its distributed file system or executing MapReduce programs require advanced knowledge in computer science and could thus prevent scientists from usage of currently available and useful software solutions. Here we present Cloudgene, a freely available platform to improve the usability of MapReduce programs in Bioinformatics by providing a graphical user interface for the execution, the import and export of data and the reproducibility of workflows on in-house (private clouds) and rented clusters (public clouds). The aim of Cloudgene is to build a standardized graphical execution environment for currently available and future MapReduce programs, which can all be integrated by using its plug-in interface. Since Cloudgene can be executed on private clusters, sensitive datasets can be kept in house at all time and data transfer times are therefore minimized. Our results show that MapReduce programs can be integrated into Cloudgene with little effort and without adding any computational overhead to existing programs. This platform gives developers the opportunity to focus on the actual implementation task and provides scientists a platform with the aim to hide the complexity of MapReduce. In addition to MapReduce programs, Cloudgene can also be used to launch predefined systems (e.g. Cloud BioLinux, RStudio) in public clouds. Currently, five different bioinformatic programs using MapReduce and two systems are integrated and have been successfully deployed. Cloudgene is

  16. Evaluating the online platform of a blended-learning pharmacist continuing education degree program

    OpenAIRE

    Wilbur, Kerry

    2016-01-01

    Background: Distance-based continuing education opportunities are increasingly embraced by health professionals worldwide. Methods: To evaluate the online component of a blended-learning degree program for pharmacists, we conducted a structured self-assessment and peer review using an instrument systematically devised according to Moore’s principles of transactional distance. The web-based platform for 14 courses was reviewed by both local and external faculty, followed by shared reflecti...

  17. First Applications of DoD Iridium RUDICS in the NSF Polar Programs

    Science.gov (United States)

    Valentic, T.; Stehle, R.

    2008-12-01

    We will present the first deployment and application of the new Iridium RUDICS service to remote instrumentation projects within the National Science Foundation's polar programs. The rise of automated observing networks has increased the demand for real-time connectivity to remote instruments, not only for immediate access to data, but to also interrogate health and status. Communicating with field sites in the polar regions is complicated by the remoteness from existing infrastructure, low temperatures and limited connection options. Sites located above 78° latitude are not able to see geostationary satellites, leaving the Iridium constellation as the only one that provide a direct connection. Some others, such as Orbcomm, only provide a store-and-forward service. Iridium is often used as a dial up modem to establish a PPP connection to the Internet with data files transferred via FTP. On low-bandwidth, high-latency networks like Iridium (2400bps with ping times of seconds), this approach is time consuming and inefficient. The dial up time alone takes upwards of a minute, and standard TCP/IP and FTP protocols are hampered by the long latencies. Minimizing transmission time is important for reducing battery usage and connection costs. The new Iridium RUDICS service can be used for more efficient transfers. RUDICS is an acronym for "Router-based Unstructured Digital Inter-working Connectivity Solution" and provides a direct connection between an instrument in the field and a server on the Internet. After dialing into the Iridium gateway, a socket connection is opened to a registered port on a user's server. Bytes sent to or from the modem appear at the server's socket. The connection time is reduced to about 10 seconds because the modem training and PPP negotiation stages are eliminated. The remote device does not need to have a full TCP/IP stack, allowing smaller instruments such as data loggers to directly handle the data transmission. Alternative protocols can

  18. NOAA's Joint Polar Satellite System's Proving Ground and Risk Reduction Program - Bringing New Capabilities to Operations!

    Science.gov (United States)

    Sjoberg, B.

    2015-12-01

    This presentation will focus on the NOAA Joint Polar Satellite System (JPSS) Program's Proving Ground and Risk Reduction (PGRR) initiative and how it has prepared NOAA users to effectively utilize new polar-orbiting capabilities. The PGRR Program was established in 2012, following the launch of the Suomi National Polar Partnership (SNPP) satellite. Two sets of PGRR Projects have been established grouped together in thirteen different initiatives. Details about how these projects have been continually tailored through the years to meet user requirements, will be highlighted. The presenter will focus on how the success of the first set of PGRR projects have been used to evaluate a follow-on set of projects and focus on exactly what the JPSS user community needs to meet their mission requirements. Details on the Dec 2014 PGRR Call-for-Proposals and the projects selected for funding will be discussed.

  19. ImaEdge - a platform for quantitative analysis of the spatiotemporal dynamics of cortical proteins during cell polarization.

    Science.gov (United States)

    Zhang, Zhen; Lim, Yen Wei; Zhao, Peng; Kanchanawong, Pakorn; Motegi, Fumio

    2017-12-15

    Cell polarity involves the compartmentalization of the cell cortex. The establishment of cortical compartments arises from the spatial bias in the activity and concentration of cortical proteins. The mechanistic dissection of cell polarity requires the accurate detection of dynamic changes in cortical proteins, but the fluctuations of cell shape and the inhomogeneous distributions of cortical proteins greatly complicate the quantitative extraction of their global and local changes during cell polarization. To address these problems, we introduce an open-source software package, ImaEdge, which automates the segmentation of the cortex from time-lapse movies, and enables quantitative extraction of cortical protein intensities. We demonstrate that ImaEdge enables efficient and rigorous analysis of the dynamic evolution of cortical PAR proteins during Caenorhabditis elegans embryogenesis. It is also capable of accurate tracking of varying levels of transgene expression and discontinuous signals of the actomyosin cytoskeleton during multiple rounds of cell division. ImaEdge provides a unique resource for quantitative studies of cortical polarization, with the potential for application to many types of polarized cells.This article has an associated First Person interview with the first authors of the paper. © 2017. Published by The Company of Biologists Ltd.

  20. Algorithms and Programs for Strong Gravitational Lensing In Kerr Space-time Including Polarization

    Science.gov (United States)

    Chen, Bin; Kantowski, Ronald; Dai, Xinyu; Baron, Eddie; Maddumage, Prasad

    2015-05-01

    Active galactic nuclei (AGNs) and quasars are important astrophysical objects to understand. Recently, microlensing observations have constrained the size of the quasar X-ray emission region to be of the order of 10 gravitational radii of the central supermassive black hole. For distances within a few gravitational radii, light paths are strongly bent by the strong gravity field of the central black hole. If the central black hole has nonzero angular momentum (spin), then a photon’s polarization plane will be rotated by the gravitational Faraday effect. The observed X-ray flux and polarization will then be influenced significantly by the strong gravity field near the source. Consequently, linear gravitational lensing theory is inadequate for such extreme circumstances. We present simple algorithms computing the strong lensing effects of Kerr black holes, including the effects on polarization. Our algorithms are realized in a program “KERTAP” in two versions: MATLAB and Python. The key ingredients of KERTAP are a graphic user interface, a backward ray-tracing algorithm, a polarization propagator dealing with gravitational Faraday rotation, and algorithms computing observables such as flux magnification and polarization angles. Our algorithms can be easily realized in other programming languages such as FORTRAN, C, and C++. The MATLAB version of KERTAP is parallelized using the MATLAB Parallel Computing Toolbox and the Distributed Computing Server. The Python code was sped up using Cython and supports full implementation of MPI using the “mpi4py” package. As an example, we investigate the inclination angle dependence of the observed polarization and the strong lensing magnification of AGN X-ray emission. We conclude that it is possible to perform complex numerical-relativity related computations using interpreted languages such as MATLAB and Python.

  1. ALGORITHMS AND PROGRAMS FOR STRONG GRAVITATIONAL LENSING IN KERR SPACE-TIME INCLUDING POLARIZATION

    International Nuclear Information System (INIS)

    Chen, Bin; Maddumage, Prasad; Kantowski, Ronald; Dai, Xinyu; Baron, Eddie

    2015-01-01

    Active galactic nuclei (AGNs) and quasars are important astrophysical objects to understand. Recently, microlensing observations have constrained the size of the quasar X-ray emission region to be of the order of 10 gravitational radii of the central supermassive black hole. For distances within a few gravitational radii, light paths are strongly bent by the strong gravity field of the central black hole. If the central black hole has nonzero angular momentum (spin), then a photon’s polarization plane will be rotated by the gravitational Faraday effect. The observed X-ray flux and polarization will then be influenced significantly by the strong gravity field near the source. Consequently, linear gravitational lensing theory is inadequate for such extreme circumstances. We present simple algorithms computing the strong lensing effects of Kerr black holes, including the effects on polarization. Our algorithms are realized in a program “KERTAP” in two versions: MATLAB and Python. The key ingredients of KERTAP are a graphic user interface, a backward ray-tracing algorithm, a polarization propagator dealing with gravitational Faraday rotation, and algorithms computing observables such as flux magnification and polarization angles. Our algorithms can be easily realized in other programming languages such as FORTRAN, C, and C++. The MATLAB version of KERTAP is parallelized using the MATLAB Parallel Computing Toolbox and the Distributed Computing Server. The Python code was sped up using Cython and supports full implementation of MPI using the “mpi4py” package. As an example, we investigate the inclination angle dependence of the observed polarization and the strong lensing magnification of AGN X-ray emission. We conclude that it is possible to perform complex numerical-relativity related computations using interpreted languages such as MATLAB and Python

  2. PyEPL: A cross-platform experiment-programming library

    Science.gov (United States)

    Geller, Aaron S.; Schleifer, Ian K.; Sederberg, Per B.; Jacobs, Joshua; Kahana, Michael J.

    2009-01-01

    PyEPL (the Python Experiment-Programming Library) is a Python library which allows cross-platform and object-oriented coding of behavioral experiments. It provides functions for displaying text and images onscreen, as well as playing and recording sound, and is capable of rendering 3-D virtual environments for spatial-navigation tasks. It is currently tested for Mac OS X and Linux. It interfaces with Activewire USB cards (on Mac OS X) and the parallel port (on Linux) for synchronization of experimental events with physiological recordings. In this article, we first present two sample programs which illustrate core PyEPL features. The examples demonstrate visual stimulus presentation, keyboard input, and simulation and exploration of a simple 3-D environment. We then describe the components and strategies used in implementing PyEPL. PMID:18183912

  3. Weight loss efficacy of a novel mobile Diabetes Prevention Program delivery platform with human coaching

    Science.gov (United States)

    Michaelides, Andreas; Raby, Christine; Wood, Meghan; Farr, Kit

    2016-01-01

    Objective To evaluate the weight loss efficacy of a novel mobile platform delivering the Diabetes Prevention Program. Research Design and Methods 43 overweight or obese adult participants with a diagnosis of prediabetes signed-up to receive a 24-week virtual Diabetes Prevention Program with human coaching, through a mobile platform. Weight loss and engagement were the main outcomes, evaluated by repeated measures analysis of variance, backward regression, and mediation regression. Results Weight loss at 16 and 24 weeks was significant, with 56% of starters and 64% of completers losing over 5% body weight. Mean weight loss at 24 weeks was 6.58% in starters and 7.5% in completers. Participants were highly engaged, with 84% of the sample completing 9 lessons or more. In-app actions related to self-monitoring significantly predicted weight loss. Conclusions Our findings support the effectiveness of a uniquely mobile prediabetes intervention, producing weight loss comparable to studies with high engagement, with potential for scalable population health management. PMID:27651911

  4. Real-Time Study of the Interaction between G-Rich DNA Oligonucleotides and Lead Ion on DNA Tetrahedron-Functionalized Sensing Platform by Dual Polarization Interferometry.

    Science.gov (United States)

    Wang, Shuang; Lu, Shasha; Zhao, Jiahui; Huang, Jianshe; Yang, Xiurong

    2017-11-29

    G-quadruplex plays roles in numerous physiological and pathological processes of organisms. Due to the unique properties of G-quadruplex (e.g., forming G4/hemin complexes with catalytic activity and electron acceptability, binding with metal ions, proteins, fluorescent ligands, and so on), it has been widely applied in biosensing. But the formation process of G-quadruplex is not yet fully understood. Here, a DNA tetrahedron platform with higher reproducibility, regenerative ability, and time-saving building process was coupled with dual polarization interferometry technique for the real-time and label-free investigation of the specific interaction process of guanine-rich singled-stranded DNA (G-rich ssDNA) and Pb 2+ . The oriented immobilization of probes greatly decreased the spatial hindrance effect and improved the accessibility of the probes to the Pb 2+ ions. Through real-time monitoring of the whole formation process of the G-quadruplex, we speculated that the probes on the tetrahedron platform initially stood on the sensing surface with a random coil conformation, then the G-rich ssDNA preliminarily formed unstable G-quartets by H-bonding and cation binding, subsequently forming a completely folded and stable quadruplex structure through relatively slow strand rearrangements. On the basis of these studies, we also developed a novel sensing platform for the specific and sensitive determination of Pb 2+ and its chelating agent ethylenediaminetetraacetic acid. This study not only provides a proof-of-concept for conformational dynamics of G-quadruplex-related drugs and pathogenes, but also enriches the biosensor tools by combining nanomaterial with interfaces technique.

  5. Multivariate Gradient Analysis for Evaluating and Visualizing a Learning System Platform for Computer Programming

    Directory of Open Access Journals (Sweden)

    Richard Mather

    2015-02-01

    Full Text Available This paper explores the application of canonical gradient analysis to evaluate and visualize student performance and acceptance of a learning system platform. The subject of evaluation is a first year BSc module for computer programming. This uses ‘Ceebot’, an animated and immersive game-like development environment. Multivariate ordination approaches are widely used in ecology to explore species distribution along environmental gradients. Environmental factors are represented here by three ‘assessment’ gradients; one for the overall module mark and two independent tests of programming knowledge and skill. Response data included Likert expressions for behavioral, acceptance and opinion traits. Behavioral characteristics (such as attendance, collaboration and independent study were regarded to be indicative of learning activity. Acceptance and opinion factors (such as perceived enjoyment and effectiveness of Ceebot were treated as expressions of motivation to engage with the learning environment. Ordination diagrams and summary statistics for canonical analyses suggested that logbook grades (the basis for module assessment and code understanding were weakly correlated. Thus strong module performance was not a reliable predictor of programming ability. The three assessment indices were correlated with behaviors of independent study and peer collaboration, but were only weakly associated with attendance. Results were useful for informing teaching practice and suggested: (1 realigning assessments to more fully capture code-level skills (important in the workplace; (2 re-evaluating attendance-based elements of module design; and (3 the overall merit of multivariate canonical gradient approaches for evaluating and visualizing the effectiveness of a learning system platform.

  6. Evaluating the online platform of a blended-learning pharmacist continuing education degree program

    Directory of Open Access Journals (Sweden)

    Kerry Wilbur

    2016-06-01

    Full Text Available Background: Distance-based continuing education opportunities are increasingly embraced by health professionals worldwide. Methods: To evaluate the online component of a blended-learning degree program for pharmacists, we conducted a structured self-assessment and peer review using an instrument systematically devised according to Moore's principles of transactional distance. The web-based platform for 14 courses was reviewed by both local and external faculty, followed by shared reflection of individual and aggregate results. Results: Findings indicated a number of course elements for modification to enhance the structure, dialog, and autonomy of the student learning experience. Conclusion: Our process was an important exercise in quality assurance and is worthwhile for other health disciplines developing and delivering distance-based content to pursue.

  7. Evaluating the online platform of a blended-learning pharmacist continuing education degree program.

    Science.gov (United States)

    Wilbur, Kerry

    2016-01-01

    Distance-based continuing education opportunities are increasingly embraced by health professionals worldwide. To evaluate the online component of a blended-learning degree program for pharmacists, we conducted a structured self-assessment and peer review using an instrument systematically devised according to Moore's principles of transactional distance. The web-based platform for 14 courses was reviewed by both local and external faculty, followed by shared reflection of individual and aggregate results. Findings indicated a number of course elements for modification to enhance the structure, dialog, and autonomy of the student learning experience. Our process was an important exercise in quality assurance and is worthwhile for other health disciplines developing and delivering distance-based content to pursue.

  8. Modular programming for tuberculosis control, the "AuTuMN" platform.

    Science.gov (United States)

    Trauer, James McCracken; Ragonnet, Romain; Doan, Tan Nhut; McBryde, Emma Sue

    2017-08-07

    Tuberculosis (TB) is now the world's leading infectious killer and major programmatic advances will be needed if we are to meet the ambitious new End TB Targets. Although mathematical models are powerful tools for TB control, such models must be flexible enough to capture the complexity and heterogeneity of the global TB epidemic. This includes simulating a disease that affects age groups and other risk groups differently, has varying levels of infectiousness depending upon the organ involved and varying outcomes from treatment depending on the drug resistance pattern of the infecting strain. We adopted sound basic principles of software engineering to develop a modular software platform for simulation of TB control interventions ("AuTuMN"). These included object-oriented programming, logical linkage between modules and consistency of code syntax and variable naming. The underlying transmission dynamic model incorporates optional stratification by age, risk group, strain and organ involvement, while our approach to simulating time-variant programmatic parameters better captures the historical progression of the epidemic. An economic model is overlaid upon this epidemiological model which facilitates comparison between new and existing technologies. A "Model runner" module allows for predictions of future disease burden trajectories under alternative scenario situations, as well as uncertainty, automatic calibration, cost-effectiveness and optimisation. The model has now been used to guide TB control strategies across a range of settings and countries, with our modular approach enabling repeated application of the tool without the need for extensive modification for each application. The modular construction of the platform minimises errors, enhances readability and collaboration between multiple programmers and enables rapid adaptation to answer questions in a broad range of contexts without the need for extensive re-programming. Such features are particularly

  9. Use of the Polarized Radiance Distribution Camera System in the RADYO Program

    Science.gov (United States)

    2011-01-28

    polarizer’s (Melles Griot , 03 FPG 019). Polarizer’s are orientated at 0 deg, 60 deg, and 120 deg (angles relative to the first polarizer). The combination...combination of a broadband mica quarter wave plate (Melles Griot , 02 WRM001) and a polarizer to form a circular polarization analyzer. The combination of the

  10. A personalized, multi-platform nutrition, exercise, and lifestyle coaching program: A pilot in women

    Directory of Open Access Journals (Sweden)

    M. Héroux

    2017-03-01

    Full Text Available The aim of this pilot study was to examine if a personalized web-based multi-platform nutrition, exercise, and lifestyle coaching program, supported weight loss and the reduction of chronic disease risk factors in overweight or obese women. Twenty-eight women completed the program, which represented 50% of those who provided baseline data. The program consisted of a one-year curriculum with daily exercise, nutritional habits, and health behaviour lessons along with access to a one-on-one coach. The workouts, habits, and lessons were available via computer, tablet, and mobile device which, along with coaching, facilitated self-monitoring and accountability. At baseline and 12-months, weight, waist circumference, fat mass, muscle mass, blood pressure, total cholesterol, low density lipoproteins, high density lipoproteins, triglycerides, C reactive protein, and fasting glucose were collected. Over the 12 months, women who completed the program, (average age 49.64 (SD 10.99 years, lost 16.52 (SD 13.63 lbs (P < 0.001, and reduced waist circumference by 3.56 (SD 2.31 in (P < 0.0001. Diastolic blood pressure decreased by 3.77 (SD 7.25 mm Hg (P = 0.02 and high density lipoproteins increased by 0.16 (SD 0.28 mmol/L (P = 0.01. No other risk factors changed significantly. Compliance was a significant predictor of weight loss (P < 0.01. In conclusion, women who completed the web-based program experienced significant weight loss (8.62% of initial body weight coming predominantly from body fat. Chronic disease risk factors also improved.

  11. Building Transferable Knowledge and Skills through an Interdisciplinary Polar Science Graduate Program

    Science.gov (United States)

    Culler, L. E.; Virginia, R. A.; Albert, M. R.; Ayres, M.

    2015-12-01

    Modern graduate education must extend beyond disciplinary content to prepare students for diverse careers in science. At Dartmouth, a graduate program in Polar Environmental Change uses interdisciplinary study of the polar regions as a core from which students develop skills and knowledge for tackling complex environmental issues that require cooperation across scientific disciplines and with educators, policy makers, and stakeholders. Two major NSF-funded initiatives have supported professional development for graduate students in this program, including an IGERT (Integrative Graduate Education and Research Traineeship) and leadership of JSEP's (Joint Science Education Project) Arctic Science Education Week in Greenland. We teach courses that emphasize the links between science and the human dimensions of environmental change; host training sessions in science communication; invite guest speakers who work in policy, academia, journalism, government research, etc.; lead an international field-based training that includes policy-focused meetings and a large outreach component; provide multiple opportunities for outreach and collaboration with local schools; and build outreach and education into graduate research programs where students instruct and mentor high school students. Students from diverse scientific disciplines (Ecology, Earth Science, and Engineering) participate in all of the above, which significantly strengthens their interdisciplinary view of polar science and ability to communicate across disciplines. In addition, graduate students have developed awareness, confidence, and the skills to pursue and obtain diverse careers. This is reflected in the fact that recent graduates have acquired permanent and post-doctoral positions in academic and government research, full-time teaching, and also in post-docs focused on outreach and science policy. Dartmouth's interdisciplinary approach to graduate education is producing tomorrow's leaders in science.

  12. Analysis of matters associated with the transferring of object-oriented applications to platform .Net using C# programming language

    Science.gov (United States)

    Sarsimbayeva, S. M.; Kospanova, K. K.

    2015-11-01

    The article provides the discussion of matters associated with the problems of transferring of object-oriented Windows applications from C++ programming language to .Net platform using C# programming language. C++ has always been considered to be the best language for the software development, but the implicit mistakes that come along with the tool may lead to infinite memory leaks and other errors. The platform .Net and the C#, made by Microsoft, are the solutions to the issues mentioned above. The world economy and production are highly demanding applications developed by C++, but the new language with its stability and transferability to .Net will bring many advantages. An example can be presented using the applications that imitate the work of queuing systems. Authors solved the problem of transferring of an application, imitating seaport works, from C++ to the platform .Net using C# in the scope of Visual Studio.

  13. Dynamic Positioning Capability Analysis for Marine Vessels Based on A DPCap Polar Plot Program

    Science.gov (United States)

    Wang, Lei; Yang, Jian-min; Xu, Sheng-wen

    2018-03-01

    Dynamic positioning capability (DPCap) analysis is essential in the selection of thrusters, in their configuration, and during preliminary investigation of the positioning ability of a newly designed vessel dynamic positioning system. DPCap analysis can help determine the maximum environmental forces, in which the DP system can counteract in given headings. The accuracy of the DPCap analysis is determined by the precise estimation of the environmental forces as well as the effectiveness of the thrust allocation logic. This paper is dedicated to developing an effective and efficient software program for the DPCap analysis for marine vessels. Estimation of the environmental forces can be obtained by model tests, hydrodynamic computation and empirical formulas. A quadratic programming method is adopted to allocate the total thrust on every thruster of the vessel. A detailed description of the thrust allocation logic of the software program is given. The effectiveness of the new program DPCap Polar Plot (DPCPP) was validated by a DPCap analysis for a supply vessel. The present study indicates that the developed program can be used in the DPCap analysis for marine vessels. Moreover, DPCap analysis considering the thruster failure mode might give guidance to the designers of vessels whose thrusters need to be safer.

  14. Comparison of two lecture delivery platforms in a hybrid distance education program.

    Science.gov (United States)

    Ried, L Douglas; Byers, Katherine

    2009-08-28

    To compare students' preferences for and academic performance using 2 different distance education course content delivery platforms. A randomized, crossover research design was used to compare traditional video with a 4-panel platform among learners on multiple campuses within 1 college of pharmacy.(1) The outcomes were students' preferences for delivery platform and examination scores. Rasch analysis was used to assess unidimensionality and the difficulty of examination items. Hierarchical logistic and multiple regression models were used to assess students' preferences and academic performance. The logistic model predicting preference for the 4-panel or traditional platform was not significant, but African-Americans and Hispanics were more likely to prefer the 4-panel platform than Caucasian and Asian students. The delivery platform did not impact students' academic performance. Students who did well on the semester's previous 2 examinations scored higher on the questions related to schizophrenia. Students with higher Pharmacy College Admission Test (PCAT) scores performed better on the bipolar questions than students who preferred the traditional video platform. The additional faculty time, effort, and cost invested in presenting the class material in a 4-panel platform, and the students' extra time and effort spent viewing the 4-panel platform did not produce a comparable benefit in student preference and performance.

  15. The status of spacecraft bus and platform technology development under the NASA ISPT program

    Science.gov (United States)

    Anderson, D. J.; Munk, M. M.; Pencil, E.; Dankanich, J.; Glaab, L.; Peterson, T.

    The In-Space Propulsion Technology (ISPT) program is developing spacecraft bus and platform technologies that will enable or enhance NASA robotic science missions. The ISPT program is currently developing technology in four areas that include Propulsion System Technologies (electric and chemical), Entry Vehicle Technologies (aerocapture and Earth entry vehicles), Spacecraft Bus and Sample Return Propulsion Technologies (components and ascent vehicles), and Systems/Mission Analysis. Three technologies are ready for near-term flight infusion: 1) the high-temperature Advanced Material Bipropellant Rocket (AMBR) engine providing higher performance; 2) NASA's Evolutionary Xenon Thruster (NEXT) ion propulsion system, a 0.6-7 kW throttle-able gridded ion system; and 3) Aerocapture technology development with investments in a family of thermal protection system (TPS) materials and structures; guidance, navigation, and control (GN& C) models of blunt-body rigid aeroshells; and aerothermal effect models. Two component technologies being developed with flight infusion in mind are the Advanced Xenon Flow Control System and ultra-lightweight propellant tank technologies. Future directions for ISPT are technologies that relate to sample return missions and other spacecraft bus technology needs like: 1) Mars Ascent Vehicles (MAV); 2) multi-mission technologies for Earth Entry Vehicles (MMEEV); and 3) electric propulsion. These technologies are more vehicles and mission-focused, and present a different set of technology development and infusion steps beyond those previously implemented. The Systems/Mission Analysis area is focused on developing tools and assessing the application of propulsion and spacecraft bus technologies to a wide variety of mission concepts. These in-space propulsion technologies are applicable, and potentially enabling for future NASA Discovery, New Frontiers, and sample return missions currently under consideration, as well as having broad applicabilit- to

  16. Development of a cryogenically cooled platform for the Magnetized Liner Inertial Fusion (MagLIF) Program

    Science.gov (United States)

    Awe, T. J.; Shelton, K. P.; Sefkow, A. B.; Lamppa, D. C.; Baker, J. L.; Rovang, D. C.; Robertson, G. K.

    2017-09-01

    A cryogenically cooled hardware platform has been developed and commissioned on the Z Facility at Sandia National Laboratories in support of the Magnetized Liner Inertial Fusion (MagLIF) Program. MagLIF is a magneto-inertial fusion concept that employs a magnetically imploded metallic tube (liner) to compress and inertially confine premagnetized and preheated fusion fuel. The fuel is preheated using a ˜2 kJ laser that must pass through a ˜1.5-3.5-μm-thick polyimide "window" at the target's laser entrance hole (LEH). As the terawatt-class laser interacts with the dense window, laser plasma instabilities (LPIs) can develop, which reduce the preheat energy delivered to the fuel, initiate fuel contamination, and degrade target performance. Cryogenically cooled targets increase the parameter space accessible to MagLIF target designs by allowing nearly 10 times thinner windows to be used for any accessible gas density. Thinner LEH windows reduce the deleterious effects of difficult to model LPIs. The Z Facility's cryogenic infrastructure has been significantly altered to enable compatibility with the premagnetization and fuel preheat stages of MagLIF. The MagLIF cryostat brings the liquid helium coolant directly to the target via an electrically resistive conduit. This design maximizes cooling power while allowing rapid diffusion of the axial magnetic field supplied by external Helmholtz-like coils. A variety of techniques have been developed to mitigate the accumulation of ice from vacuum chamber contaminants on the cooled LEH window, as even a few hundred nanometers of ice would impact laser energy coupling to the fuel region. The MagLIF cryostat has demonstrated compatibility with the premagnetization and preheat stages of MagLIF and the ability to cool targets to liquid deuterium temperatures in approximately 5 min.

  17. Industrial Robotics Platform for Simulation Design, Planning and Optimization based on Off-line CAD Programming

    Directory of Open Access Journals (Sweden)

    Baizid Khelifa

    2016-01-01

    Full Text Available This paper presents IRoSim: Industrial Robotics Simulation Design Planning and Optimization platform which we developed based on SolidWorks API. The main objective is to integrate features from mechanical and robotics CAD software into the same platform in order to facilitate the development process through a friendly interaction interface. The platform provides important steps to develop a given robotized task such as: defining a given task, CAD learning of the end-effectors’ trajectory, checking the manipulator’s reach-ability to perform a task, simulating the motion and preventing the trajectory from possible collisions. To assess the usability of the proposed platform, a car’s doors painting task using a 6 Degree Of Freedom industrial manipulator has been developed.

  18. Prevention validation and accounting platform: a framework for establishing accountability and performance measures of substance abuse prevention programs.

    Science.gov (United States)

    Kim, S; McLeod, J H; Williams, C; Hepler, N

    2000-01-01

    The field of substance abuse prevention has neither an overarching conceptual framework nor a set of shared terminologies for establishing the accountability and performance outcome measures of substance abuse prevention services rendered. Hence, there is a wide gap between what we currently have as data on one hand and information that are required to meet the performance goals and accountability measures set by the Government Performance and Results Act of 1993 on the other. The task before us is: How can we establish the accountability and performance measures of substance abuse prevention programs and transform the field of prevention into prevention science? The intent of this volume is to serve that purpose and accelerate the processes of this transformation by identifying the requisite components of the transformation (i.e., theory, methodology, convention on terms, and data) and by introducing an open forum called, Prevention Validation and Accounting (PREVA) Platform. The entire PREVA Platform (for short, the Platform) is designed as an analytic framework, which is formulated by a collectivity of common concepts, terminologies, accounting units, protocols for counting the units, data elements, and operationalizations of various constructs, and other summary measures intended to bring about an efficient and effective measurement of process input, program capacity, process output, performance outcome, and societal impact of substance abuse prevention programs. The measurement units and summary data elements are designed to be measured across time and across jurisdictions, i.e., from local to regional to state to national levels. In the Platform, the process input is captured by two dimensions of time and capital. Time is conceptualized in terms of service delivery time and time spent for research and development. Capital is measured by the monies expended for the delivery of program activities during a fiscal or reporting period. Program capacity is captured

  19. The MaCWAVE program to study gravity wave influences on the polar mesosphere

    Directory of Open Access Journals (Sweden)

    R. A. Goldberg

    2006-07-01

    Full Text Available MaCWAVE (Mountain and Convective Waves Ascending VErtically was a highly coordinated rocket, ground-based, and satellite program designed to address gravity wave forcing of the mesosphere and lower thermosphere (MLT. The MaCWAVE program was conducted at the Norwegian Andøya Rocket Range (ARR, 69.3° N in July 2002, and continued at the Swedish Rocket Range (Esrange, 67.9° N during January 2003. Correlative instrumentation included the ALOMAR MF and MST radars and RMR and Na lidars, Esrange MST and meteor radars and RMR lidar, radiosondes, and TIMED (Thermosphere Ionosphere Mesosphere Energetics and Dynamics satellite measurements of thermal structures. The data have been used to define both the mean fields and the wave field structures and turbulence generation leading to forcing of the large-scale flow. In summer, launch sequences coupled with ground-based measurements at ARR addressed the forcing of the summer mesopause environment by anticipated convective and shear generated gravity waves. These motions were measured with two 12-h rocket sequences, each involving one Terrier-Orion payload accompanied by a mix of MET rockets, all at ARR in Norway. The MET rockets were used to define the temperature and wind structure of the stratosphere and mesosphere. The Terrier-Orions were designed to measure small-scale plasma fluctuations and turbulence that might be induced by wave breaking in the mesosphere. For the summer series, three European MIDAS (Middle Atmosphere Dynamics and Structure rockets were also launched from ARR in coordination with the MaCWAVE payloads. These were designed to measure plasma and neutral turbulence within the MLT. The summer program exhibited a number of indications of significant departures of the mean wind and temperature structures from ``normal" polar summer conditions, including an unusually warm mesopause and

  20. The MaCWAVE program to study gravity wave influences on the polar mesosphere

    Directory of Open Access Journals (Sweden)

    R. A. Goldberg

    2006-07-01

    Full Text Available MaCWAVE (Mountain and Convective Waves Ascending VErtically was a highly coordinated rocket, ground-based, and satellite program designed to address gravity wave forcing of the mesosphere and lower thermosphere (MLT. The MaCWAVE program was conducted at the Norwegian Andøya Rocket Range (ARR, 69.3° N in July 2002, and continued at the Swedish Rocket Range (Esrange, 67.9° N during January 2003. Correlative instrumentation included the ALOMAR MF and MST radars and RMR and Na lidars, Esrange MST and meteor radars and RMR lidar, radiosondes, and TIMED (Thermosphere Ionosphere Mesosphere Energetics and Dynamics satellite measurements of thermal structures. The data have been used to define both the mean fields and the wave field structures and turbulence generation leading to forcing of the large-scale flow. In summer, launch sequences coupled with ground-based measurements at ARR addressed the forcing of the summer mesopause environment by anticipated convective and shear generated gravity waves. These motions were measured with two 12-h rocket sequences, each involving one Terrier-Orion payload accompanied by a mix of MET rockets, all at ARR in Norway. The MET rockets were used to define the temperature and wind structure of the stratosphere and mesosphere. The Terrier-Orions were designed to measure small-scale plasma fluctuations and turbulence that might be induced by wave breaking in the mesosphere. For the summer series, three European MIDAS (Middle Atmosphere Dynamics and Structure rockets were also launched from ARR in coordination with the MaCWAVE payloads. These were designed to measure plasma and neutral turbulence within the MLT. The summer program exhibited a number of indications of significant departures of the mean wind and temperature structures from ``normal" polar summer conditions, including an unusually warm mesopause and a slowing of the formation of polar mesospheric summer echoes (PMSE and noctilucent clouds (NLC. This

  1. Ice-tethered measurement platforms in the Arctic Ocean: a contribution by the FRAM infrastructure program

    Science.gov (United States)

    Hoppmann, Mario; Nicolaus, Marcel; Rabe, Benjamin; Wenzhöfer, Frank; Katlein, Christian; Scholz, Daniel

    2016-04-01

    The Arctic Ocean has been in the focus of many studies during recent years, investigating the state, the causes and the implications of the observed rapid transition towards a thinner and younger sea-ice cover. However, consistent observational datasets of sea ice, ocean and atmosphere are still sparse due to the limited accessibility and harsh environmental conditions. One important tool to fill this gap has become more and more feasible during recent years: autonomous, ice-tethered measurement platforms (buoys). These drifting instruments independently transmit their data via satellites, and enable observations over larger areas and over longer time periods than manned expeditions, even throughout the winter. One aim of the newly established FRAM (FRontiers in Arctic marine Monitoring) infrastructure program at the Alfred-Wegener-Institute is to realize and maintain an interdisciplinary network of buoys in the Arctic Ocean, contributing to an integrated, Arctic-wide observatory. The additional buoy infrastructure, ship-time, and developments provided by FRAM are critical elements in the ongoing international effort to fill the large data gaps in a rapidly changing Arctic Ocean. Our focus is the particularly underrepresented Eurasian Basin. Types of instruments range from snow depth beacons and ice mass balance buoys for monitoring ice growth and snow accumulation, over radiation and weather stations for energy budget estimates, to ice-tethered profiling systems for upper ocean monitoring. Further, development of new bio-optical and biogeochemical buoys is expected to enhance our understanding of bio-physical processes associated with Arctic sea ice. The first set of FRAM buoys was deployed in September 2015 from RV Polarstern. All datasets are publicly available on dedicated web portals. Near real time data are reported into international initiatives, such as the Global Telecommunication System (GTS) and the International Arctic Buoy Programme (IABP). The

  2. Genomic prediction unifies animal and plant breeding programs to form platforms for biological discovery

    DEFF Research Database (Denmark)

    Hickey, John M.; Chiurugwi, Tinashe; Mackay, Ian

    2017-01-01

    use. However, achieving higher, sustainable rates of improvement in yields in various species will require renewed genetic interventions and dramatic improvement of agricultural practices. Genomic prediction of breeding values has the potential to improve selection, reduce costs and provide a platform...

  3. The Effect of In-Service Training of Computer Science Teachers on Scratch Programming Language Skills Using an Electronic Learning Platform on Programming Skills and the Attitudes towards Teaching Programming

    Science.gov (United States)

    Alkaria, Ahmed; Alhassan, Riyadh

    2017-01-01

    This study was conducted to examine the effect of in-service training of computer science teachers in Scratch language using an electronic learning platform on acquiring programming skills and attitudes towards teaching programming. The sample of this study consisted of 40 middle school computer science teachers. They were assigned into two…

  4. A population-wide screening and tailored intervention platform for eating disorders on college campuses: the healthy body image program.

    Science.gov (United States)

    Jones, Megan; Kass, Andrea E; Trockel, Mickey; Glass, Alan I; Wilfley, Denise E; Taylor, C Barr

    2014-01-01

    This article presents a new approach to intervention for eating disorders and body image concerns on college campuses, using a model of integrated eating disorder screening and intervention. Formative data on implementation feasibility are presented. College students enrolled at 2 universities between 2011 and 2012. The Healthy Body Image program is an evidence-based screening and intervention platform, enacted via community and online resources. An online screen was used to identify students at varying levels of risk or eating disorder symptom status; responses were used to direct students to universal or targeted online interventions or further evaluation. Universal prevention programs to improve healthy weight regulation and body image culture were offered to all students. Formative data from 1,551 students illustrates the application of this model. The Healthy Body Image program is feasible to deliver and provides a comprehensive system of screening, evidence-based intervention, and community culture change.

  5. AI based HealthCare Platform for Real Time, Predictive and Prescriptive Analytics using Reactive Programming

    Science.gov (United States)

    Kaur, Jagreet; Singh Mann, Kulwinder, Dr.

    2018-01-01

    AI in Healthcare needed to bring real, actionable insights and Individualized insights in real time for patients and Doctors to support treatment decisions., We need a Patient Centred Platform for integrating EHR Data, Patient Data, Prescriptions, Monitoring, Clinical research and Data. This paper proposes a generic architecture for enabling AI based healthcare analytics Platform by using open sources Technologies Apache beam, Apache Flink Apache Spark, Apache NiFi, Kafka, Tachyon, Gluster FS, NoSQL- Elasticsearch, Cassandra. This paper will show the importance of applying AI based predictive and prescriptive analytics techniques in Health sector. The system will be able to extract useful knowledge that helps in decision making and medical monitoring in real-time through an intelligent process analysis and big data processing.

  6. The National Mechatronic Platform. The basis of the educational programs in the knowledge society

    Science.gov (United States)

    Maties, V.

    2016-08-01

    The shift from the information society to the knowledge based society caused by the mechatronic revolution, that took place in the 9th decade of the last century, launched a lot of challenges for education and researches activities too. Knowledge production development asks for new educational technologies to stimulate the initiative and creativity as a base to increase the productivity in the knowledge production. The paper presents details related on the innovative potential of mechatronics as educational environment for transdisciplinarity learning and integral education. The basic infrastructure of that environment is based on mechatronic platforms. In order to develop the knowledge production at the national level the specific structures are to be developed. The paper presents details related on the structure of the National Mechatronic Platform as a true knowledge factory. The benefits of the effort to develop the specific infrastructure for knowledge production in the field of mechatronics are outlined too.

  7. The simulated clinical environment as a platform for refining critical thinking in nursing students: a pilot program.

    Science.gov (United States)

    Wane, Daryle; Lotz, Karen

    2013-01-01

    This research explores the use of clinical simulations as a platform for stimulating critical thinking in nursing students. This study takes place in an associate degree nursing program with a clinical group of nursing students. Utilizing a faculty partnership approach, information was presented to the clinical group. Students were divided into small groups to create simulation scenarios. Students were able to appreciate complexity of care and research differential diagnoses as they applied to care and management of changes in client condition scenarios. Use of a small-group teaching method to develop, implement, and critique clinical simulation scenarios facilitated critical thinking and clinical judgment of nursing students.

  8. Use of Web 2.0 Social Media Platforms to Promote Community-Engaged Research Dialogs: A Preliminary Program Evaluation.

    Science.gov (United States)

    Valdez Soto, Miguel; Balls-Berry, Joyce E; Bishop, Shawn G; Aase, Lee A; Timimi, Farris K; Montori, Victor M; Patten, Christi A

    2016-09-09

    Community-engaged research is defined by the Institute of Medicine as the process of working collaboratively with groups of people affiliated by geographic proximity, special interests, or similar situations with respect to issues affecting their well-being. Traditional face-to-face community-engaged research is limited by geographic location, limited in resources, and/or uses one-way communications. Web 2.0 technologies including social media are novel communication channels for community-engaged research because these tools can reach a broader audience while promoting bidirectional dialogs. This paper reports on a preliminary program evaluation of the use of social media platforms for promoting engagement of researchers and community representatives in dialogs about community-engaged research. For this pilot program evaluation, the Clinical and Translational Science Office for Community Engagement in Research partnered with the Social Media Network at our institution to create a WordPress blog and Twitter account. Both social media platforms were facilitated by a social media manager. We used descriptive analytics for measuring engagement with WordPress and Twitter over an 18-month implementation period during 2014-2016. For the blog, we examined type of user (researcher, community representative, other) and used content analysis to generate the major themes from blog postings. For use of Twitter, we examined selected demographics and impressions among followers. There were 76 blog postings observed from researchers (48/76, 64%), community representatives (23/76, 32%) and funders (5/76, 8%). The predominant themes of the blog content were research awareness and dissemination of community-engaged research (35/76, 46%) and best practices (23/76, 30%). For Twitter, we obtained 411 followers at the end of the 18-month evaluation period, with an increase of 42% (from 280 to 411) over the final 6 months. Followers reported varied geographic location (321/411, 78

  9. Use of Web 2.0 Social Media Platforms to Promote Community-Engaged Research Dialogs: A Preliminary Program Evaluation

    Science.gov (United States)

    Valdez Soto, Miguel; Bishop, Shawn G; Aase, Lee A; Timimi, Farris K; Montori, Victor M; Patten, Christi A

    2016-01-01

    Background Community-engaged research is defined by the Institute of Medicine as the process of working collaboratively with groups of people affiliated by geographic proximity, special interests, or similar situations with respect to issues affecting their well-being. Traditional face-to-face community-engaged research is limited by geographic location, limited in resources, and/or uses one-way communications. Web 2.0 technologies including social media are novel communication channels for community-engaged research because these tools can reach a broader audience while promoting bidirectional dialogs. Objective This paper reports on a preliminary program evaluation of the use of social media platforms for promoting engagement of researchers and community representatives in dialogs about community-engaged research. Methods For this pilot program evaluation, the Clinical and Translational Science Office for Community Engagement in Research partnered with the Social Media Network at our institution to create a WordPress blog and Twitter account. Both social media platforms were facilitated by a social media manager. We used descriptive analytics for measuring engagement with WordPress and Twitter over an 18-month implementation period during 2014-2016. For the blog, we examined type of user (researcher, community representative, other) and used content analysis to generate the major themes from blog postings. For use of Twitter, we examined selected demographics and impressions among followers. Results There were 76 blog postings observed from researchers (48/76, 64%), community representatives (23/76, 32%) and funders (5/76, 8%). The predominant themes of the blog content were research awareness and dissemination of community-engaged research (35/76, 46%) and best practices (23/76, 30%). For Twitter, we obtained 411 followers at the end of the 18-month evaluation period, with an increase of 42% (from 280 to 411) over the final 6 months. Followers reported varied

  10. Integration of the program TNXYZ in the platform SALOME; Integracion del programa TNXYZ en la plataforma SALOME

    Energy Technology Data Exchange (ETDEWEB)

    Chaparro V, F. J.; Silva A, L.; Del Valle G, E. [IPN, Escuela Superior de Fisica y Matematicas, Av. Instituto Politecnico Nacional s/n, U.P. Adolfo Lopez Mateos, Edificio 9, Col. San Pedro Zacatenco, 07738 Mexico D. F. (Mexico); Gomez T, A. M.; Vargas E, S., E-mail: javier.paquito@hotmail.com [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)

    2013-10-15

    This work presents the procedure realized to integrate the code TNXYZ like a processing tool to the graphic simulation platform SALOME. The code TNXYZ solves the neutron transport equation in stationary state, for several energy groups, quantizing the angular variable by the discrete ordinates method and the space variable by nodal methods. The platform SALOME is a graphic surrounding designed for the construction, edition and simulation of mechanical models focused to the industry and contrary to other software, it allows to integrate external source codes to the surrounding, to form a complete scheme of execution, supervision, pre and post information processing. The code TNXYZ was programmed in the 90s in a Fortran compiler, but to be used at the present time the code should be actualized to the current compiler characteristics; also, in the original scheme was carried out a modularization process, that is to say, the main program was divided in sections where the code carries out important operations, with the intention of flexibility the data extraction process along its processing sequence and that can be useful in a later development of coupling. Finally, to verify the integration a fuel assembly BWR was modeled, as well as a control cell. The cross sections were obtained with the Monte Carlo Serpent code. Some results obtained with Serpent were used to verify and to begin with the validation of the code, being obtained an acceptable comparison in the infinite multiplication factor. The validation process should extend and one has planned to present in a future work. This work is part of the development of the research group formed between the Escuela Superior de Fisica y Matematicas del Instituto Politecnico Nacional (IPN) and the Instituto Nacional de Investigaciones Nucleares (ININ) in which a simulation Mexican platform of nuclear reactors is developed. (Author)

  11. Genomic prediction unifies animal and plant breeding programs to form platforms for biological discovery.

    Science.gov (United States)

    Hickey, John M; Chiurugwi, Tinashe; Mackay, Ian; Powell, Wayne

    2017-08-30

    The rate of annual yield increases for major staple crops must more than double relative to current levels in order to feed a predicted global population of 9 billion by 2050. Controlled hybridization and selective breeding have been used for centuries to adapt plant and animal species for human use. However, achieving higher, sustainable rates of improvement in yields in various species will require renewed genetic interventions and dramatic improvement of agricultural practices. Genomic prediction of breeding values has the potential to improve selection, reduce costs and provide a platform that unifies breeding approaches, biological discovery, and tools and methods. Here we compare and contrast some animal and plant breeding approaches to make a case for bringing the two together through the application of genomic selection. We propose a strategy for the use of genomic selection as a unifying approach to deliver innovative 'step changes' in the rate of genetic gain at scale.

  12. An Investigation of a Computer Training Company's Migration to a New Distance Learning Platform and the Implementation of an Online Professional Development Program

    Science.gov (United States)

    Rudd, Denis; Bernadowski, Carianne

    2015-01-01

    The purpose of the study was to determine if the Training Partner Program was successful in preparing trainers to use a new distance learning platform. Results indicate the program was a success in improving self-efficacy, engagement, and collaboration among trainers. Additionally, characteristics of online trainers are identified. Online learning…

  13. Sensor programming and concept implementation of a temperature monitoring system, using Arduino as prototyping platform

    DEFF Research Database (Denmark)

    Sbîrnă, Sebastian; Søberg, Peder Veng; Sbîrnă, Liana Simona

    2016-01-01

    The present work reports the programming paradigms that have been developed for a temperature monitoring system able to provide accurate data regarding food temperatures inside refrigerated vehicles and alert the driver accordingly, in relation to which temperature states are encountered. The men......The present work reports the programming paradigms that have been developed for a temperature monitoring system able to provide accurate data regarding food temperatures inside refrigerated vehicles and alert the driver accordingly, in relation to which temperature states are encountered...

  14. SOLUTION OF MICROECONOMICS ASSIGNMENTS BY THE MEANS OF PROGRAM MODULES ISPEZ ON THE DISTANCE PLATFORM MOODLE

    Directory of Open Access Journals (Sweden)

    V. М. Kobets

    2010-04-01

    Full Text Available In article basic aspects introduction integrated environment verification knowledge students from microeconomic are expounded. It is considered structure of Decision Environmental with the built-in program modules (mathematical and graphical editors for the decision of typical assignments from microeconomics during the current and final control of students’ knowledges of different forms of teaching.

  15. RoboMind. A platform for on-the-fly programming and inspection of behavior-based robot programs

    OpenAIRE

    Svendsen, Alexander

    2014-01-01

    Lego Mindstorms is a popular tool used by universities for educational and demonstrational purposes. Lego Mindstorms is a set of buildable and programmable robotic kits, made by Lego. It allows for a high level of participation from the audience, while being easily programmable. However, for demonstrational and recruitment purposes, it is not without shortcomings. When there is a limited time to talk to people, it is difficult to explain and change a running Lego Mindstorm program. Typically ...

  16. The Nautilus Exploration Program: Utilizing Live Ocean Exploration as a Platform for STEM Education and Outreach

    Science.gov (United States)

    Fundis, A.; Cook, M.; Sutton, K.; Garson, S.; Poulton, S.; Munro, S.

    2016-02-01

    By sparking interest in scientific inquiry and engineering design at a young age through exposure to ocean exploration and innovative technologies, and building on that interest throughout students' educational careers, the Ocean Exploration Trust (OET) aims to motivate more students to be lifelong learners and pursue careers in STEM fields. Utilizing research conducted aboard Exploration Vessel Nautilus, the ship's associated technologies, and shore-based facilities at the University of Rhode Island — including the Graduate School of Oceanography and the Inner Space Center — we guide students to early career professionals through a series of educational programs focused on STEM disciplines and vocational skills. OET also raises public awareness of ocean exploration and research through a growing online presence, live streaming video, and interactions with the team aboard the ship 24 hours a day via the Nautilus Live website (www.nautiluslive.org). Annually, our outreach efforts bring research launched from Nautilus to tens of millions worldwide and allow the public, students, and scientists to participate in expeditions virtually from shore. We share the Nautilus Exploration Program's strategies, successes, and lessons learned for a variety of our education and outreach efforts including: 1) enabling global audiences access to live ocean exploration online and via social media; 2) engaging onshore audiences in live and interactive conversations with scientists and engineers on board; 3) engaging young K-12 learners in current oceanographic research via newly developed lessons and curricula; 4) onshore and offshore professional development opportunities for formal and informal educators; 5) programs and authentic research opportunities for high school, undergraduate, and graduate students onshore and aboard Nautilus; and 6) collaborative opportunities for early career and seasoned researchers to participate virtually in telepresence-enabled, interdisciplinary

  17. PlasmaDNA: a free, cross-platform plasmid manipulation program for molecular biology laboratories

    Directory of Open Access Journals (Sweden)

    Rainy Jeffrey

    2007-09-01

    Full Text Available Abstract Background Most molecular biology experiments, and the techniques associated with this field of study, involve a great deal of engineering in the form of molecular cloning. Like all forms of engineering, perfect information about the starting material is crucial for successful completion of design and strategies. Results We have generated a program that allows complete in silico simulation of the cloning experiment. Starting with a primary DNA sequence, PlasmaDNA looks for restriction sites, open reading frames, primer annealing sequences, and various common domains. The databases are easily expandable by the user to fit his most common cloning needs. PlasmaDNA can manage and graphically represent multiple sequences at the same time, and keeps in memory the overhangs at the end of the sequences if any. This means that it is possible to virtually digest fragments, to add the digestion products to the project, and to ligate together fragments with compatible ends to generate the new sequences. Polymerase Chain Reaction (PCR fragments can also be virtually generated using the primer database, automatically adding to the fragments any 5' extra sequences present in the primers. Conclusion PlasmaDNA is a program available both on Windows and Apple operating systems, designed to facilitate molecular cloning experiments by building a visual map of the DNA. It then allows the complete planning and simulation of the cloning experiment. It also automatically updates the new sequences generated in the process, which is an important help in practice. The capacity to maintain multiple sequences in the same file can also be used to archive the various steps and strategies involved in the cloning of each construct. The program is freely available for download without charge or restriction.

  18. Platform projections, compilers, interpreters and portability

    NARCIS (Netherlands)

    Bergstra, J.A.; Loots, M.E.

    1999-01-01

    Platform projection semantics extends projection semantics by means of the encapsulation of a processor used for program execution. Platform projection semantics abstracts from platform specific details. For a given program its platform projection semantics may be platform-independent. Two forms

  19. Parallel Conjugate Gradient: Effects of Ordering Strategies, Programming Paradigms, and Architectural Platforms

    Science.gov (United States)

    Oliker, Leonid; Heber, Gerd; Biswas, Rupak

    2000-01-01

    The Conjugate Gradient (CG) algorithm is perhaps the best-known iterative technique to solve sparse linear systems that are symmetric and positive definite. A sparse matrix-vector multiply (SPMV) usually accounts for most of the floating-point operations within a CG iteration. In this paper, we investigate the effects of various ordering and partitioning strategies on the performance of parallel CG and SPMV using different programming paradigms and architectures. Results show that for this class of applications, ordering significantly improves overall performance, that cache reuse may be more important than reducing communication, and that it is possible to achieve message passing performance using shared memory constructs through careful data ordering and distribution. However, a multi-threaded implementation of CG on the Tera MTA does not require special ordering or partitioning to obtain high efficiency and scalability.

  20. Effectiveness of an impairment-based individualized rehabilitation program using an iPad-based software platform

    Directory of Open Access Journals (Sweden)

    Carrie Alice Des Roches

    2015-01-01

    Full Text Available The delivery of tablet-based rehabilitation for individuals with post-stroke aphasia is relatively new, therefore, this study examined the effectiveness of an iPad-based therapy to demonstrate improvement in specific therapy tasks and how the tasks affect overall language and cognitive skills. Fifty-one individuals with aphasia due to a stroke or traumatic brain injury were recruited to use an iPad-based software platform, Constant Therapy, for a 10 week therapy program. Participants were split into an experimental (N=42 and control (N=9 group. Both experimental and control participants received a one hour clinic session with a clinician once a week, the experimental participants additionally practiced the therapy at home. Participants did not differ in the duration of the therapy and both groups of participants showed improvement over time in the tasks used for the therapy. However, experimental participants used the application more often and showed greater changes in accuracy and latency on the tasks than the control participants; experimental participants’ severity level at baseline as measured by standardized tests of language and cognitive skills were a factor in improvement on the tasks. Subgroups of task co-improvement appear to occur between different language tasks, between different cognitive tasks, and across both domains. Finally, experimental participants showed more significant and positive changes due to therapy in their standardized tests than control participants. These results provide preliminary evidence for the usefulness of a tablet-based platform to deliver tailored language and cognitive therapy to individuals with aphasia.

  1. Effectiveness of an impairment-based individualized rehabilitation program using an iPad-based software platform.

    Science.gov (United States)

    Des Roches, Carrie A; Balachandran, Isabel; Ascenso, Elsa M; Tripodis, Yorghos; Kiran, Swathi

    2014-01-01

    The delivery of tablet-based rehabilitation for individuals with post-stroke aphasia is relatively new, therefore, this study examined the effectiveness of an iPad-based therapy to demonstrate improvement in specific therapy tasks and how the tasks affect overall language and cognitive skills. Fifty-one individuals with aphasia due to a stroke or traumatic brain injury (TBI) were recruited to use an iPad-based software platform, Constant Therapy, for a 10 week therapy program. Participants were split into an experimental (N = 42) and control (N = 9) group. Both experimental and control participants received a 1 h clinic session with a clinician once a week, the experimental participants additionally practiced the therapy at home. Participants did not differ in the duration of the therapy and both groups of participants showed improvement over time in the tasks used for the therapy. However, experimental participants used the application more often and showed greater changes in accuracy and latency on the tasks than the control participants; experimental participants' severity level at baseline as measured by standardized tests of language and cognitive skills were a factor in improvement on the tasks. Subgroups of task co-improvement appear to occur between different language tasks, between different cognitive tasks, and across both domains. Finally, experimental participants showed more significant and positive changes due to therapy in their standardized tests than control participants. These results provide preliminary evidence for the usefulness of a tablet-based platform to deliver tailored language and cognitive therapy to individuals with aphasia.

  2. Delayed polarization of mononuclear phagocyte transcriptional program by type I interferon isoforms

    Directory of Open Access Journals (Sweden)

    Wang Ena

    2005-06-01

    Full Text Available Abstract Background Interferon (IFN-α is considered a key modulator of immunopathological processes through a signature-specific activation of mononuclear phagocytes (MPs. This study utilized global transcript analysis to characterize the effects of the entire type I IFN family in comparison to a broad panel of other cytokines on MP previously exposed to Lipopolysaccharide (LPS stimulation in vitro. Results Immature peripheral blood CD14+ MPs were stimulated with LPS and 1 hour later with 42 separate soluble factors including cytokines, chemokines, interleukins, growth factors and IFNs. Gene expression profiling of MPs was analyzed 4 and 9 hours after cytokine stimulation. Four hours after stimulation, the transcriptional analysis of MPs revealed two main classes of cytokines: one associated with the alternative and the other with the classical pathway of MP activation without a clear polarization of type I IFNs effects. In contrast, after 9 hours of stimulation most type I IFN isoforms induced a characteristic and unique transcriptional pattern separate from other cytokines. These "signature" IFNs included; IFN-β, IFN-α2b/α2, IFN-αI, IFN-α2, IFN-αC, IFN-αJ1, IFN-αH2, and INF-α4B and induced the over-expression of 44 genes, all of which had known functional relationships with IFN such as myxovirus resistance (Mx-1, Mx-2, and interferon-induced hepatitis C-associated microtubular aggregation protein. A second group of type I IFNs segregated separately and in closer association with the type II IFN-γ. The phylogenetic relationship of amino acid sequences among type I IFNs did not explain their sub-classification, although differences at positions 94 through 109 and 175 through 189 were present between the signature and other IFNs. Conclusion Seven IFN-α isoforms and IFN-β participate in the late phase polarization of MPs conditioned by LPS. This information broadens the previous view of the central role played by IFN-α in

  3. Platform Constellations

    DEFF Research Database (Denmark)

    Staykova, Kalina Stefanova; Damsgaard, Jan

    2016-01-01

    This research paper presents an initial attempt to introduce and explain the emergence of new phenomenon, which we refer to as platform constellations. Functioning as highly modular systems, the platform constellations are collections of highly connected platforms which co-exist in parallel...... and as such allow us to study platforms not only as separate entities, but also to investigate the relationship between several platforms offered and governed by one and the same platform provider. By investigating two case studies of indigenous platform constellations formed around the hugely popular instant...

  4. Polarization Optics

    OpenAIRE

    Fressengeas, Nicolas

    2010-01-01

    The physics of polarization optics *Polarized light propagation *Partially polarized light; DEA; After a brief introduction to polarization optics, this lecture reviews the basic formalisms for dealing with it: Jones Calculus for totally polarized light and Stokes parameters associated to Mueller Calculus for partially polarized light.

  5. Integration of the TNXYZ computer program inside the platform Salome; Integracion del programa de computo TNXYZ dentro de la plataforma Salome

    Energy Technology Data Exchange (ETDEWEB)

    Chaparro V, F. J.

    2014-07-01

    The present work shows the procedure carried out to integrate the code TNXYZ as a calculation tool at the graphical simulation platform Salome. The TNXYZ code propose a numerical solution of the neutron transport equation, in several groups of energy, steady-state and three-dimensional geometry. In order to discretized the variables of the transport equation, the code uses the method of discrete ordinates for the angular variable, and a nodal method for the spatial dependence. The Salome platform is a graphical environment designed for building, editing and simulating mechanical models mainly focused on the industry and unlike other software, in order to form a complete scheme of pre and post processing of information, to integrate and control an external source code. Before the integration the in the Salome platform TNXYZ code was upgraded. TNXYZ was programmed in the 90s using Fortran 77 compiler; for this reason the code was adapted to the characteristics of the current Fortran compilers; in addition, with the intention of extracting partial results over the process sequence, the original structure of the program underwent a modularization process, i.e. the main program was divided into sections where the code performs major operations. This procedure is controlled by the information module (YACS) on Salome platform, and it could be useful for a subsequent coupling with thermal-hydraulics codes. Finally, with the help of the Monte Carlo code Serpent several study cases were defined in order to check the process of integration; the verification process consisted in performing a comparison of the results obtained with the code executed as stand-alone and after modernized, integrated and controlled by the Salome platform. (Author)

  6. Ship emissions measurement in the Arctic by plume intercepts of the Canadian Coast Guard icebreaker Amundsen from the Polar 6 aircraft platform

    Directory of Open Access Journals (Sweden)

    A. A. Aliabadi

    2016-06-01

    Full Text Available Decreasing sea ice and increasing marine navigability in northern latitudes have changed Arctic ship traffic patterns in recent years and are predicted to increase annual ship traffic in the Arctic in the future. Development of effective regulations to manage environmental impacts of shipping requires an understanding of ship emissions and atmospheric processing in the Arctic environment. As part of the summer 2014 NETCARE (Network on Climate and Aerosols campaign, the plume dispersion and gas and particle emission factors of effluents originating from the Canadian Coast Guard icebreaker Amundsen operating near Resolute Bay, NU, Canada, were investigated. The Amundsen burned distillate fuel with 1.5 wt % sulfur. Emissions were studied via plume intercepts using the Polar 6 aircraft measurements, an analytical plume dispersion model, and using the FLEXPART-WRF Lagrangian particle dispersion model. The first plume intercept by the research aircraft was carried out on 19 July 2014 during the operation of the Amundsen in the open water. The second and third plume intercepts were carried out on 20 and 21 July 2014 when the Amundsen had reached the ice edge and operated under ice-breaking conditions. Typical of Arctic marine navigation, the engine load was low compared to cruising conditions for all of the plume intercepts. The measured species included mixing ratios of CO2, NOx, CO, SO2, particle number concentration (CN, refractory black carbon (rBC, and cloud condensation nuclei (CCN. The results were compared to similar experimental studies in mid-latitudes. Plume expansion rates (γ were calculated using the analytical model and found to be γ  =  0.75 ± 0.81, 0.93 ± 0.37, and 1.19 ± 0.39 for plumes 1, 2, and 3, respectively. These rates were smaller than prior studies conducted at mid-latitudes, likely due to polar boundary layer dynamics, including reduced turbulent mixing compared to mid-latitudes. All emission

  7. Hip2Norm: an object-oriented cross-platform program for 3D analysis of hip joint morphology using 2D pelvic radiographs.

    Science.gov (United States)

    Zheng, G; Tannast, M; Anderegg, C; Siebenrock, K A; Langlotz, F

    2007-07-01

    We developed an object-oriented cross-platform program to perform three-dimensional (3D) analysis of hip joint morphology using two-dimensional (2D) anteroposterior (AP) pelvic radiographs. Landmarks extracted from 2D AP pelvic radiographs and optionally an additional lateral pelvic X-ray were combined with a cone beam projection model to reconstruct 3D hip joints. Since individual pelvic orientation can vary considerably, a method for standardizing pelvic orientation was implemented to determine the absolute tilt/rotation. The evaluation of anatomically morphologic differences was achieved by reconstructing the projected acetabular rim and the measured hip parameters as if obtained in a standardized neutral orientation. The program had been successfully used to interactively objectify acetabular version in hips with femoro-acetabular impingement or developmental dysplasia. Hip(2)Norm is written in object-oriented programming language C++ using cross-platform software Qt (TrollTech, Oslo, Norway) for graphical user interface (GUI) and is transportable to any platform.

  8. Analytical polarization calculations beyond SLIM

    International Nuclear Information System (INIS)

    Barber, D.P.

    1989-01-01

    A comparison is made between the theories of Bell and Leinaas and of Derbenev and Kondratenko for the spin polarization in electron storage rings. A calculation of polarization in HERA using the program SMILE of Mane is presented

  9. ENERGY STAR® Retail Products Platform (RPP): Conditions and Considerations in Evaluating Market Transformation Programs and Evaluation Guidance for RPP

    Energy Technology Data Exchange (ETDEWEB)

    Li, Michael [U.S. Department of Energy; Banwell, Peter [U.S. Environmental Protection Agency

    2018-01-09

    The purpose of this guide is to provide a resource for state utility regulators, utilities, the evaluation community and regulatory stakeholders on methods to measure energy savings from the ENERGY STAR Retail Products Platform (link is external). The guidelines outlined in this document were developed by evaluation experts.

  10. Comparing the effects of exercise program and low-level laser therapy with exercise program and polarized polychromatic non-coherent light (bioptron light) on the treatment of lateral elbow tendinopathy.

    Science.gov (United States)

    Stasinopoulos, Dimitrios; Stasinopoulos, Ioannis; Pantelis, Manias; Stasinopoulou, Kalliopi

    2009-06-01

    The use of low-level laser therapy (LLLT) and polarized polychromatic non-coherent light as supplements to an exercise program has been recommended for the management of lateral elbow tendinopathy (LET). To investigate whether an exercise program supplemented with LLLT is more successful than an exercise program supplemented with polarized polychromatic non-coherent light in treating LET. Patients with unilateral LET for at least 4 wk were sequentially allocated to receive either an exercise program with LLLT or an exercise program with polarized polychromatic non-coherent light. The exercise program consisted of eccentric and static stretching exercises of wrist extensors. In the LLLT group a 904-nm Ga-As laser was used in continuous mode, and the power density was 130 mW/cm(2), and the dose was 0.585 J/point. In the group receiving polarized polychromatic non-coherent light the Bioptron 2 was used to administer the dose perpendicularly to the lateral epicondyle at three points at an operating distance of 5-10 cm for 6 min at each position. The outcome measures were pain and function and were evaluated at baseline, at the end of the treatment (week 4), and 3 mo after the end of treatment (week 16). Fifty patients met the inclusion criteria. At the end of treatment there was a decline in pain and a rise in function in both groups compared with baseline (p 0.0005 on the independent t-test). The results suggest that the combination of an exercise program with LLLT or polarized polychromatic non-coherent light is an adequate treatment for patients with LET. Further research to establish the relative and absolute effectiveness of such a treatment approach is needed.

  11. Polarized Electrons at Jefferson Laboratory

    Energy Technology Data Exchange (ETDEWEB)

    Sinclair, C.K.

    1997-12-31

    The CEBAF accelerator at Jefferson laboratory can deliver CW electron beams to three experimental halls simultaneously. A large fraction of the approved scientific program at the lab requires polarized electron beams. Many of these experiments, both polarized and unpolarized, require high average beam current as well. Since all electrons delivered to the experimental halls originate from the same cathode, delivery of polarized beam to a single hall requires using the polarized source to deliver beam to all experiments in simultaneous operation. The polarized source effort at Jefferson Lab is directed at obtaining very long polarized source operational lifetimes at high average current and beam polarization; at developing the capability to deliver all electrons leaving the polarized source to the experimental halls; and at delivering polarized beam to multiple experimental halls simultaneously.initial operational experience with the polarized source will be presented.

  12. Polarized electrons at Jefferson laboratory

    International Nuclear Information System (INIS)

    The CEBAF accelerator at Jefferson laboratory can deliver CW electron beams to three experimental halls simultaneously. A large fraction of the approved scientific program at the lab requires polarized electron beams. Many of these experiments, both polarized and unpolarized, require high average beam current as well. Since all electrons delivered to the experimental halls originate from the same cathode, delivery of polarized beam to a single hall requires using the polarized source to deliver beam to all experiments in simultaneous operation. The polarized source effort at Jefferson Lab is directed at obtaining very long polarized source operational lifetimes at high average current and beam polarization; at developing the capability to deliver all electrons leaving the polarized source to the experimental halls; and at delivering polarized beam to multiple experimental halls simultaneously. Initial operational experience with the polarized source will be presented

  13. Development of a program in LABVIEW platform to controlling and monitoring a Sievert-type system for comminution of metallic uranium and its alloys

    International Nuclear Information System (INIS)

    Dutra, Aimore R.R.; Ferraz, Wilmar B.; Ferreira, Ricardo A.N.

    2011-01-01

    A comminution process by hydriding-dehydriding method was developed at CDTN-Centro de Desenvolvimento da Tecnologia Nuclear with the purpose of obtaining plate type nuclear fuel. This fuel requires the use of metallic uranium and its alloys in form of powders. This comminution process was performed based on a Sievert system. Initially this system was controlled and monitored by a computer program developed in Turbo Pascal language. In order to improve the control of the comminution process, a new program was developed in LabVIEW platform. This paper presents a description of this new program and the main aspects of the operation of the system. The more accurate monitoring and controlling of the various stages of the comminution process as well as greater flexibility in the choice of input data, real-time graphics, generation of reports and a reduction of time passivation were achieved. (author)

  14. Development of a program in LABVIEW platform to controlling and monitoring Sievert-type system for comminution of metallic uranium and its alloys

    International Nuclear Information System (INIS)

    Dutra, Aimore R.R.; Ferraz, Wilmar B.; Ferreira, Ricardo A.N.

    2011-01-01

    A comminution process by hydriding-de hydriding method was developed at CDTN-Centro de Desenvolvimento da Tecnologia Nuclear with the purpose of obtaining plate type nuclear fuel. This fuel requires the use of metallic uranium and its alloys in form of powders. This comminution process was performed based on a Sievert system. Initially this system was controlled and monitored by a computer program developed in Turbo Pascal language. In order to improve the control of the comminution process, a new program was developed in LabVIEW platform. This paper presents a description of this new program and the main aspects of the operation of the system. The more accurate monitoring and controlling of the various stages of the comminution process as well as greater flexibility in the choice of input data, real-time graphics, generation of reports and a reduction of time passivation were achieved. (author)

  15. Development of a program in LABVIEW platform to controlling and monitoring a Sievert-type system for comminution of metallic uranium and its alloys

    Energy Technology Data Exchange (ETDEWEB)

    Dutra, Aimore R.R.; Ferraz, Wilmar B.; Ferreira, Ricardo A.N., E-mail: ferrazw@cdtn.b, E-mail: ranf@cdtn.b [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

    2011-07-01

    A comminution process by hydriding-dehydriding method was developed at CDTN-Centro de Desenvolvimento da Tecnologia Nuclear with the purpose of obtaining plate type nuclear fuel. This fuel requires the use of metallic uranium and its alloys in form of powders. This comminution process was performed based on a Sievert system. Initially this system was controlled and monitored by a computer program developed in Turbo Pascal language. In order to improve the control of the comminution process, a new program was developed in LabVIEW platform. This paper presents a description of this new program and the main aspects of the operation of the system. The more accurate monitoring and controlling of the various stages of the comminution process as well as greater flexibility in the choice of input data, real-time graphics, generation of reports and a reduction of time passivation were achieved. (author)

  16. Development of a program in LABVIEW platform to controlling and monitoring Sievert-type system for comminution of metallic uranium and its alloys

    Energy Technology Data Exchange (ETDEWEB)

    Dutra, Aimore R.R.; Ferraz, Wilmar B.; Ferreira, Ricardo A.N., E-mail: ferrazw@cdtn.b, E-mail: ranf@cdtn.b [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

    2011-07-01

    A comminution process by hydriding-de hydriding method was developed at CDTN-Centro de Desenvolvimento da Tecnologia Nuclear with the purpose of obtaining plate type nuclear fuel. This fuel requires the use of metallic uranium and its alloys in form of powders. This comminution process was performed based on a Sievert system. Initially this system was controlled and monitored by a computer program developed in Turbo Pascal language. In order to improve the control of the comminution process, a new program was developed in LabVIEW platform. This paper presents a description of this new program and the main aspects of the operation of the system. The more accurate monitoring and controlling of the various stages of the comminution process as well as greater flexibility in the choice of input data, real-time graphics, generation of reports and a reduction of time passivation were achieved. (author)

  17. Myosin helical pitch angle as a quantitative imaging biomarker for characterization of cardiac programming in fetal growth restriction measured by polarization second harmonic microscopy

    Science.gov (United States)

    Amat-Roldan, I.; Psilodimitrakopoulos, S.,; Eixarch, E.,; Torre, I.; Wotjas, B.; Crispi, F.; Figueras, F.; Artigas, D.,; Loza-Alvarez, P.; Gratacos, E.,

    2009-07-01

    Fetal growth restriction (FGR) has recently shown a strong association with cardiac programming which predisposes to cardiovascular mortality in adulthood. Polarization Second Harmonic Microscopy can quantify molecular architecture changes with high sensitivity in cardiac myofibrils. In this work, we use myosin helical pitch angle as an example to quantify such alterations related to this high risk population. Importantly, this shows a potential use of the technique as an early diagnostic tool and an alternative method to understand pathophysiological processes.

  18. Payment Platform

    DEFF Research Database (Denmark)

    Hjelholt, Morten; Damsgaard, Jan

    2012-01-01

    Payment transactions through the use of physical coins, bank notes or credit cards have for centuries been the standard formats of exchanging money. Recently online and mobile digital payment platforms has entered the stage as contenders to this position and possibly could penetrate societies...... applies a co-evolutionary multilevel perspective to model the interplay and processes between technology and society wherein digital payment platforms potentially will substitute other payment platforms just like the credit card negated the check. On this basis this paper formulate a multilevel conceptual...... framework and shows, through examples of new digital payment platforms, how transitions and substitutions might occur. Finally we discuss how possible venues and routes of transitions appear in the genesis and evolution of digital payment platforms....

  19. The European platform for financial education as incentive for the national efforts in implementing financial literacy programs: The case of the Association of Serbian Banks

    Directory of Open Access Journals (Sweden)

    Sredojević Slađana

    2017-01-01

    Full Text Available A sustainable financial system relies on two pillars: the functional and healthy financial institutions, as well as the financially competent customers-investors-entrepreneurs. The responsibility for the implementation of training programs and preparation for the well-informed choice does not lie only with the natural persons and legal entities. This is a shared responsibility of different stakeholders: individuals, families, small and medium enterprises, public administration, the Ministry of Education, the financial services sector, employers and representatives of trade unions and consumer protection organizations as well as other civil society initiatives. A prime example of such an integrated approach towards the same goal is the European Platform for Financial Education, an initiative launched by the European Banking Federation, the European Banking Training Network and other institutions (professional associations, in February 2017 in Brussels as an incentive for the national level efforts in implementing the respective financial literacy programs. In this paper we analyzed the importance and role of the European Platform for Financial Education in the case of the Serbian banking sector through the activities of the Association of Serbian Banks. These activities will be implemented by the Association of Banks of Serbia continuously throughout the year, and after the celebration of the European Money Week on 27-31 March 2017.

  20. Polarized Proton Collisions at RHIC

    CERN Document Server

    Bai, Mei; Alekseev, Igor G; Alessi, James; Beebe-Wang, Joanne; Blaskiewicz, Michael; Bravar, Alessandro; Brennan, Joseph M; Bruno, Donald; Bunce, Gerry; Butler, John J; Cameron, Peter; Connolly, Roger; De Long, Joseph; Drees, Angelika; Fischer, Wolfram; Ganetis, George; Gardner, Chris J; Glenn, Joseph; Hayes, Thomas; Hseuh Hsiao Chaun; Huang, Haixin; Ingrassia, Peter; Iriso, Ubaldo; Laster, Jonathan S; Lee, Roger C; Luccio, Alfredo U; Luo, Yun; MacKay, William W; Makdisi, Yousef; Marr, Gregory J; Marusic, Al; McIntyre, Gary; Michnoff, Robert; Montag, Christoph; Morris, John; Nicoletti, Tony; Oddo, Peter; Oerter, Brian; Osamu, Jinnouchi; Pilat, Fulvia Caterina; Ptitsyn, Vadim; Roser, Thomas; Satogata, Todd; Smith, Kevin T; Svirida, Dima; Tepikian, Steven; Tomas, Rogelio; Trbojevic, Dejan; Tsoupas, Nicholaos; Tuozzolo, Joseph; Vetter, Kurt; Wilinski, Michelle; Zaltsman, Alex; Zelenski, Anatoli; Zeno, Keith; Zhang, S Y

    2005-01-01

    The Relativistic Heavy Ion Collider~(RHIC) provides not only collisions of ions but also collisions of polarized protons. In a circular accelerator, the polarization of polarized proton beam can be partially or fully lost when a spin depolarizing resonance is encountered. To preserve the beam polarization during acceleration, two full Siberian snakes were employed in RHIC to avoid depolarizing resonances. In 2003, polarized proton beams were accelerated to 100~GeV and collided in RHIC. Beams were brought into collisions with longitudinal polarization at the experiments STAR and PHENIX by using spin rotators. RHIC polarized proton run experience demonstrates that optimizing polarization transmission efficiency and improving luminosity performance are significant challenges. Currently, the luminosity lifetime in RHIC is limited by the beam-beam effect. The current state of RHIC polarized proton program, including its dedicated physics run in 2005 and efforts to optimize luminosity production in beam-beam limite...

  1. Experimental study of gluon and sea quark polarizations (The first stage of the POLEX program at UNK)

    International Nuclear Information System (INIS)

    Akimenko, S.A.

    1992-01-01

    The experiments with various polarized beams and targets for searching spin effects in such processes as χ-, direct photon- and massive lepton-pairs productions are proposed. The goal is to clear up a wide range of problems on the spin-dependent quark and gluon structure functions. 35 refs.; 18 figs.; 5 tabs

  2. Common tester platform concept.

    Energy Technology Data Exchange (ETDEWEB)

    Hurst, Michael James

    2008-05-01

    This report summarizes the results of a case study on the doctrine of a common tester platform, a concept of a standardized platform that can be applicable across the broad spectrum of testing requirements throughout the various stages of a weapons program, as well as across the various weapons programs. The common tester concept strives to define an affordable, next-generation design that will meet testing requirements with the flexibility to grow and expand; supporting the initial development stages of a weapons program through to the final production and surveillance stages. This report discusses a concept investing key leveraging technologies and operational concepts combined with prototype tester-development experiences and practical lessons learned gleaned from past weapons programs.

  3. Indian social safety net programs as platforms for introducing wheat flour fortification: a case study of Gujarat, India.

    Science.gov (United States)

    Fiedler, John L; Babu, Sunil; Smitz, Marc-Francois; Lividini, Keith; Bermudez, Odilia

    2012-03-01

    Micronutrient deficiencies exact an enormous health burden on India. The release of the National Family Health Survey results--showing the relatively wealthy state of Gujarat having deficiency levels exceeding national averages--prompted Gujarat officials to introduce fortified wheat flour in their social safety net programs (SSNPs). To provide a case study of the introduction of fortified wheat flour in Gujarat's Public Distribution System (PDS), Integrated Child Development Scheme (ICDS), and Mid-Day Meal (MDM) Programme to assess the coverage, costs, impact, and cost-effectiveness of the initiative. India's 2004/05 National Sample Survey data were used to identify beneficiaries of each of Gujarat's three SSNPs and to estimate usual intake levels of vitamin A, iron, and zinc. Comparing age- and sex-specific usual intakes to Estimated Average Requirements, the proportion of the population with inadequate intakes was estimated. Postfortification intake levels and reductions in inadequate intake were estimated. The incremental cost of fortifying wheat flour and the cost-effectiveness of each program were estimated. When each program was assessed independently, the proportion of the population with inadequate vitamin A intakes was reduced by 34% and 74% among MDM and ICDS beneficiaries, respectively. Both programs effectively eliminated inadequate intakes of both iron and zinc. Among PDS beneficiaries, the proportion with inadequate iron intakes was reduced by 94%. CONCLUSIONS. Gujarat's substitution of fortified wheat flour for wheat grain is dramatically increasing the intake of micronutrients among its SSNP beneficiaries. The incremental cost of introducing fortification in each of the programs is low, and, according to World Health Organization criteria, each program is "highly cost-effective." The introduction of similar reforms throughout India would largely eliminate the inadequate iron intake among persons participating in any of the three SSNPs and would

  4. Payment Platform

    DEFF Research Database (Denmark)

    Hjelholt, Morten; Damsgaard, Jan

    2012-01-01

    Payment transactions through the use of physical coins, bank notes or credit cards have for centuries been the standard formats of exchanging money. Recently online and mobile digital payment platforms has entered the stage as contenders to this position and possibly could penetrate societies...

  5. Platform computing

    CERN Multimedia

    2002-01-01

    "Platform Computing releases first grid-enabled workload management solution for IBM eServer Intel and UNIX high performance computing clusters. This Out-of-the-box solution maximizes the performance and capability of applications on IBM HPC clusters" (1/2 page) .

  6. U.S. Space Station Platform - Configuration Technology For Customer Servicing

    Science.gov (United States)

    Dezio, Joseph A.; Walton, Barbara A.

    1987-10-01

    The design of the Space Station Platforms incorporates and expands on the serviceability and modularity features of the Multi-mission Modular Spacecraft (MMS). This design is adaptable to a wide range of mission requirements through the use of distributed systems with sizing granularity applicable to both multi-use missions, such as earth observations, and large facility missions such as astrophysics observatories. The design permits on-orbit growth, repair, instrument change-out, and resupply of propulsion fuel and cryogen at the Space Station Servicing Facility or with the Shuttle and Orbital Maneuvering Vehicle (OMV). The Platform Program encompasses the design and development of the orbiting unmanned elements of the Space Station to conduct long-term, autonomous, commercial, scien-tific, and technology ventures and investigations. These unmanned elements fall into two general classes of platforms: the Co-Orbiting Platform (COP) and the Polar Orbiting Platform (POP). The COP for the initial operating phase will be developed to support solar and stellar viewing astrophysics missions. The POP will be developed to accommodate earth observation, oceanographic, atmospheric, and solar and plasma physics missions. Current Shuttle payload capability limitations at the Western Test Range (WTR) place a restriction on another objective of platform designs for polar applications, which is to accomplish meaningful science or payload operations after one launch. For this reason, the POP will also be designed to be launched using Expendable Launch Vehicles (ELV's). Features of the Space Station Co-Orbiting and Polar Platforms are described that will allow them to be con-figured optimally to meet mission requirements and to be assembled, serviced, and modified on-orbit.

  7. Polarization developments

    International Nuclear Information System (INIS)

    Prescott, C.Y.

    1993-07-01

    Recent developments in laser-driven photoemission sources of polarized electrons have made prospects for highly polarized electron beams in a future linear collider very promising. This talk discusses the experiences with the SLC polarized electron source, the recent progress with research into gallium arsenide and strained gallium arsenide as a photocathode material, and the suitability of these cathode materials for a future linear collider based on the parameters of the several linear collider designs that exist

  8. PyGaze: an open-source, cross-platform toolbox for minimal-effort programming of eyetracking experiments.

    Science.gov (United States)

    Dalmaijer, Edwin S; Mathôt, Sebastiaan; Van der Stigchel, Stefan

    2014-12-01

    The PyGaze toolbox is an open-source software package for Python, a high-level programming language. It is designed for creating eyetracking experiments in Python syntax with the least possible effort, and it offers programming ease and script readability without constraining functionality and flexibility. PyGaze can be used for visual and auditory stimulus presentation; for response collection via keyboard, mouse, joystick, and other external hardware; and for the online detection of eye movements using a custom algorithm. A wide range of eyetrackers of different brands (EyeLink, SMI, and Tobii systems) are supported. The novelty of PyGaze lies in providing an easy-to-use layer on top of the many different software libraries that are required for implementing eyetracking experiments. Essentially, PyGaze is a software bridge for eyetracking research.

  9. The Status of Spacecraft Bus and Platform Technology Development under the NASA In-Space Propulsion Technology Program

    Science.gov (United States)

    Anderson, David; Pencil, Eric J.; Glaab, Louis; Falck, Robert D.; Dankanich, John

    2013-01-01

    NASA's In-Space Propulsion Technology (ISPT) program has been developing technologies for lowering the cost of planetary science missions. The technology areas include electric propulsion technologies, spacecraft bus technologies, entry vehicle technologies, and design tools for systems analysis and mission trajectories. The electric propulsion technologies include critical components of both gridded and non-gridded ion propulsion systems. The spacecraft bus technologies under development include an ultra-lightweight tank (ULTT) and advanced xenon feed system (AXFS). The entry vehicle technologies include the development of a multi-mission entry vehicle, mission design tools and aerocapture. The design tools under development include system analysis tools and mission trajectory design tools.

  10. Establishing Esri ArcGIS Enterprise Platform Capabilities to Support Response Activities of the NASA Earth Science Disasters Program

    Science.gov (United States)

    Molthan, A.; Seepersad, J.; Shute, J.; Carriere, L.; Duffy, D.; Tisdale, B.; Kirschbaum, D.; Green, D. S.; Schwizer, L.

    2017-12-01

    NASA's Earth Science Disasters Program promotes the use of Earth observations to improve the prediction of, preparation for, response to, and recovery from natural and technological disasters. NASA Earth observations and those of domestic and international partners are combined with in situ observations and models by NASA scientists and partners to develop products supporting disaster mitigation, response, and recovery activities among several end-user partners. These products are accompanied by training to ensure proper integration and use of these materials in their organizations. Many products are integrated along with other observations available from other sources in GIS-capable formats to improve situational awareness and response efforts before, during and after a disaster. Large volumes of NASA observations support the generation of disaster response products by NASA field center scientists, partners in academia, and other institutions. For example, a prediction of high streamflows and inundation from a NASA-supported model may provide spatial detail of flood extent that can be combined with GIS information on population density, infrastructure, and land value to facilitate a prediction of who will be affected, and the economic impact. To facilitate the sharing of these outputs in a common framework that can be easily ingested by downstream partners, the NASA Earth Science Disasters Program partnered with Esri and the NASA Center for Climate Simulation (NCCS) to establish a suite of Esri/ArcGIS services to support the dissemination of routine and event-specific products to end users. This capability has been demonstrated to key partners including the Federal Emergency Management Agency using a case-study example of Hurricane Matthew, and will also help to support future domestic and international disaster events. The Earth Science Disasters Program has also established a longer-term vision to leverage scientists' expertise in the development and delivery of

  11. ITS Platform

    DEFF Research Database (Denmark)

    Tøfting, Svend; Lahrmann, Harry; Agerholm, Niels

    2014-01-01

    for safer and more economic driving is technologically possible. Big Data from the system can provide traffic authorities with a better basis for decision for their traffic planning. Last, but not least, it is possible to establish payment systems. The project has also shown that the boxes in the cars do...... GPS box with data connection to a backend server. The ITS Platform project has had a budget of DKK 33 million (app € 4.4) and it has demonstrated that boxes which register the position of the cars can be helpful to drivers in many ways. Establishing dynamic traffic information and support systems...... not have to be very intelligent. This is gradually taken over by applications on smart phones. The ITS Platform with 425 test drivers is now completely developed and can be used for technological testing of e.g. payment systems....

  12. AGS polarized H- source

    International Nuclear Information System (INIS)

    Kponou, A.; Alessi, J.G.; Sluyters, T.

    1985-01-01

    The AGS polarized H - source is now operational. During a month-long experimental physics run in July 1984, pulses equivalent to 15 μA x 300 μs (approx. 3 x 10 10 protons) were injected into the RFQ preaccelerator. Beam polarization, measured at 200 MeV, was approx. 75%. After the run, a program to increase the H - yield of the source was begun and significant progress has been made. The H - current is now frequently 20 to 30 μA. A description of the source and some details of our operating experience are given. We also briefly describe the improvement program

  13. Polarization, political

    NARCIS (Netherlands)

    Wojcieszak, M.; Mazzoleni, G.; Barnhurst, K.G.; Ikeda, K.; Maia, R.C.M.; Wessler, H.

    2015-01-01

    Polarization has been studied in three different forms: on a social, group, and individual level. This entry first focuses on the undisputed phenomenon of elite polarization (i.e., increasing adherence of policy positions among the elites) and also outlines different approaches to assessing mass

  14. Polarization holography

    DEFF Research Database (Denmark)

    Nikolova, L.; Ramanujam, P.S.

    Current research into holography is concerned with applications in optically storing, retrieving, and processing information. Polarization holography has many unique properties compared to conventional holography. It gives results in high efficiency, achromaticity, and special polarization...... properties. This books reviews the research carried out in this field over the last 15 years. The authors provide basic concepts in polarization and the propagation of light through anisotropic materials, before presenting a sound theoretical basis for polarization holography. The fabrication...... and characterization of azobenzene based materials, which remain the most efficient for the purpose, is described in detail. This is followed by a description of other materials that are used in polarization holography. An in-depth description of various applications, including display holography and optical storage...

  15. Polar Bears

    Science.gov (United States)

    Amstrup, Steven C.; Douglas, David C.; Reynolds, Patricia E.; Rhode, E.B.

    2002-01-01

    Polar bears (Ursus maritimus) are hunted throughout most of their range. In addition to hunting polar bears of the Beaufort Sea region are exposed to mineral and petroleum extraction and related human activities such as shipping road-building, and seismic testing (Stirling 1990).Little was known at the start of this project about how polar bears move about in their environment, and although it was understood that many bears travel across political borders, the boundaries of populations had not been delineated (Amstrup 1986, Amstrup et al. 1986, Amstrup and DeMaster 1988, Garner et al. 1994, Amstrup 1995, Amstrup et al. 1995, Amstrup 2000).As human populations increase and demands for polar bears and other arctic resources escalate, managers must know the sizes and distributions of the polar bear populations. Resource managers also need reliable estimates of breeding rates, reproductive intervals, litter sizes, and survival of young and adults.Our objectives for this research were 1) to determine the seasonal and annual movements of polar bears in the Beaufort Sea, 2) to define the boundaries of the population(s) using this region, 3) to determine the size and status of the Beaufort Sea polar bear population, and 4) to establish reproduction and survival rates (Amstrup 2000).

  16. PEPPo: Using a Polarized Electron Beam to Produce Polarized Positrons

    Energy Technology Data Exchange (ETDEWEB)

    Adeyemi, Adeleke H. [Hampton Univ., Hampton, VA (United States); et al.

    2015-09-01

    Polarized positron beams have been identified as either an essential or a significant ingredient for the experimental program of both the present and next generation of lepton accelerators (JLab, Super KEK B, ILC, CLIC). An experiment demonstrating a new method for producing polarized positrons has been performed at the Continuous Electron Beam Accelerator Facility at Jefferson Lab. The PEPPo (Polarized Electrons for Polarized Positrons) concept relies on the production of polarized e⁻/e⁺ pairs from the bremsstrahlung radiation of a longitudinally polarized electron beam interacting within a high-Z conversion target. PEPPo demonstrated the effective transfer of spin-polarization of an 8.2 MeV/c polarized (P~85%) electron beam to positrons produced in varying thickness tungsten production targets, and collected and measured in the range of 3.1 to 6.2 MeV/c. In comparison to other methods this technique reveals a new pathway for producing either high-energy or thermal polarized positron beams using a relatively low polarized electron beam energy (~10MeV) .This presentation will describe the PEPPo concept, the motivations of the experiment and high positron polarization achieved.

  17. [Effectiveness of a stretching program on anxiety levels of workers in a logistic platform: a randomized controlled study].

    Science.gov (United States)

    Montero-Marín, Jesús; Asún, Sonia; Estrada-Marcén, Nerea; Romero, Rosario; Asún, Roberto

    2013-01-01

    To study the influence of a short programme of stretching exercises on anxiety levels of workers in a Spanish logistic company. A controlled clinical trial was carried out by means of an inter-subject design of random homogeneous blocks. Participants were assigned to the experimental group (n=67), treated with a programme of stretching exercises of 10-minute duration after working hours for a period of 3 months, or to the untreated control group (n=67). The primary result variable was anxiety, and the secondary variables were burnout syndrome, quality of life and flexibility. An analysis of covariance (ANCOVA) by intention to treat was performed on each of the result variables by controlling the baseline scores, the age and the practice of introjective activities outside the program, with the size effect calculated by means of the partial eta-squared value (η(2)). The results of the ANCOVA showed a moderate effect of the stretching exercise programme on the levels of anxiety (η(2)=0,06; P=.004). Other effects found were substantial for flexibility (η(2)=0,13; P<.001); moderately high for bodily pain (η(2)=0,08; P=.001), and moderate for vitality (η(2)=0,05; P=.016); mental health (η(2)=0,05; P=.017); general health (η(2)=0,04; P=.028) and exhaustion (η(2)=0,04; P=.025). The implementation of a short programme of stretching exercises in the work place was effective for reducing levels of anxiety, bodily pain and exhaustion, and for raising levels of vitality, mental health, general health and flexibility. This type of intervention could be seen as a low-cost strategy for improving the well-being of workers. Copyright © 2013 Elsevier España, S.L. All rights reserved.

  18. Development of massive multilevel molecular dynamics simulation program, Platypus (PLATform for dYnamic Protein Unified Simulation), for the elucidation of protein functions.

    Science.gov (United States)

    Takano, Yu; Nakata, Kazuto; Yonezawa, Yasushige; Nakamura, Haruki

    2016-05-05

    A massively parallel program for quantum mechanical-molecular mechanical (QM/MM) molecular dynamics simulation, called Platypus (PLATform for dYnamic Protein Unified Simulation), was developed to elucidate protein functions. The speedup and the parallelization ratio of Platypus in the QM and QM/MM calculations were assessed for a bacteriochlorophyll dimer in the photosynthetic reaction center (DIMER) on the K computer, a massively parallel computer achieving 10 PetaFLOPs with 705,024 cores. Platypus exhibited the increase in speedup up to 20,000 core processors at the HF/cc-pVDZ and B3LYP/cc-pVDZ, and up to 10,000 core processors by the CASCI(16,16)/6-31G** calculations. We also performed excited QM/MM-MD simulations on the chromophore of Sirius (SIRIUS) in water. Sirius is a pH-insensitive and photo-stable ultramarine fluorescent protein. Platypus accelerated on-the-fly excited-state QM/MM-MD simulations for SIRIUS in water, using over 4000 core processors. In addition, it also succeeded in 50-ps (200,000-step) on-the-fly excited-state QM/MM-MD simulations for the SIRIUS in water. © 2016 The Authors. Journal of Computational Chemistry Published by Wiley Periodicals, Inc.

  19. Polarized proton collider at RHIC

    Energy Technology Data Exchange (ETDEWEB)

    Alekseev, I.; Allgower, C.; Bai, M.; Batygin, Y.; Bozano, L.; Brown, K.; Bunce, G.; Cameron, P.; Courant, E.; Erin, S.; Escallier, J.; Fischer, W.; Gupta, R.; Hatanaka, K.; Huang, H.; Imai, K.; Ishihara, M.; Jain, A.; Lehrach, A.; Kanavets, V.; Katayama, T.; Kawaguchi, T.; Kelly, E.; Kurita, K.; Lee, S.Y.; Luccio, A.; MacKay, W.W. E-mail: mackay@bnl.govhttp://www.rhichome.bnl.gov/People/waldowaldo@bnl.gov; Mahler, G.; Makdisi, Y.; Mariam, F.; McGahern, W.; Morgan, G.; Muratore, J.; Okamura, M.; Peggs, S.; Pilat, F.; Ptitsin, V.; Ratner, L.; Roser, T.; Saito, N.; Satoh, H.; Shatunov, Y.; Spinka, H.; Syphers, M.; Tepikian, S.; Tominaka, T.; Tsoupas, N.; Underwood, D.; Vasiliev, A.; Wanderer, P.; Willen, E.; Wu, H.; Yokosawa, A.; Zelenski, A.N

    2003-03-01

    In addition to heavy ion collisions (RHIC Design Manual, Brookhaven National Laboratory), RHIC will also collide intense beams of polarized protons (I. Alekseev, et al., Design Manual Polarized Proton Collider at RHIC, Brookhaven National Laboratory, 1998, reaching transverse energies where the protons scatter as beams of polarized quarks and gluons. The study of high energy polarized protons beams has been a long term part of the program at BNL with the development of polarized beams in the Booster and AGS rings for fixed target experiments. We have extended this capability to the RHIC machine. In this paper we describe the design and methods for achieving collisions of both longitudinal and transverse polarized protons in RHIC at energies up to {radical}s=500 GeV.

  20. Configuration Manual Polarized Proton Collider at RHIC

    Energy Technology Data Exchange (ETDEWEB)

    Alekseev, I.; Allgower, C.; Bai, M.; Batygin, Y.; Bozano, L.; Brown, K.; Bunce, G.; Cameron, P.; Courant, E.; Erin, S.; Escallier, J.; Fischer, W.; Gupta, R.; Hatanka, K.; Huang, H.; Imai, K.; Ishihara, M.; Jain, A.; Kanavets, V.; Katayama, T.; Kawaguchi, T.; Kelly, E.; Kurita, K.; Lee, S. Y.; Luccio, A.; MacKay, W. W.; Mahler, G.; Makdisi, Y.; Mariam, F.; McGahern, W.; Morgan, G.; Muratore, J.; Okamura, M.; Peggs, S.; Pilat, F.; Ptitsin, V.; Ratner, L.; Roser, T.; Saito, N.; Satoh, H.; Shatunov, Y.; Spinka, H.; Svirida, D.; Syphers, M.; Tepikian, S.; Tominaka, T.; Tsoupas, N.; Underwood, D.; Vasiliev, A.; Wanderer, P.; Willen, E.; Wu, H.; Yokosawa, A.; Zelenski, A.

    2006-01-01

    In this report we present our design to accelerate and store polarized protons in RHIC, with the level of polarization, luminosity, and control of systematic errors required by the approved RHIC spin physics program. We provide an overview of the physics to be studied using RHIC with polarized proton beams, and a brief description of the accelerator systems required for the project.

  1. CONFIGURATION MANUAL POLARIZED PROTON COLLIDER AT RHIC.

    Energy Technology Data Exchange (ETDEWEB)

    ROSER,T.; MACKAY,W.W.; ALEKSEEV,I.; BAI,M.; BROWN,K.; BUNCE,G.; CAMERON,P.; COURANT,E.; ET AL.

    2001-03-01

    In this report, the authors present their design to accelerate and store polarized protons in RHIC, with the level of polarization, luminosity, and control of systematic errors required by the approved RHIC spin physics program. They provide an overview of the physics to be studied using RHIC with polarized proton beams, and a brief description of the accelerator systems required for the project.

  2. Secure OSGi Platform against Service Injection

    Science.gov (United States)

    Kim, Intae; Rim, Keewook; Lee, Junghyun

    OSGi platform provides Java-based open standard programming interface that enables communication and control among devices at home. Service-oriented, component based software systems built using OSGi are extensible and adaptable but they entail new types of security concerns. Security concerns in OSGi platforms can be divided into two basic categories: vulnerabilities in Java cross-platform (or multi-platform) technology and vulnerabilities in the OSGi framework. This paper identifies a new OSGi platform-specific security vulnerability called a service injection attack and proposes two mechanisms of protection against this newly identified security risk in the OSGi framework.

  3. Political polarization

    OpenAIRE

    Dixit, Avinash K.; Weibull, Jörgen W.

    2007-01-01

    Failures of government policies often provoke opposite reactions from citizens; some call for a reversal of the policy, whereas others favor its continuation in stronger form. We offer an explanation of such polarization, based on a natural bimodality of preferences in political and economic contexts and consistent with Bayesian rationality.

  4. Political polarization.

    Science.gov (United States)

    Dixit, Avinash K; Weibull, Jörgen W

    2007-05-01

    Failures of government policies often provoke opposite reactions from citizens; some call for a reversal of the policy, whereas others favor its continuation in stronger form. We offer an explanation of such polarization, based on a natural bimodality of preferences in political and economic contexts and consistent with Bayesian rationality.

  5. Current meter components and other data from FIXED PLATFORMS in support of the Physical Oceanography Field Program Offshore North Carolina from 19 February 1992 (NODC Accession 9400063)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Current meter components data were collected from FIXED PLATFORMS in the NW Atlantic (limit-40 W) from 19 February 1992. Data were collected by the Science...

  6. A feasibility study to develop a diabetes prevention program for young adults with prediabetes by using digital platforms and a handheld device.

    Science.gov (United States)

    Cha, EunSeok; Kim, Kevin H; Umpierrez, Guillermo; Dawkins, Colleen R; Bello, Morenike K; Lerner, Hannah M; Narayan, K M Venkat; Dunbar, Sandra B

    2014-01-01

    The purpose of this pilot study was to examine the feasibility and preliminary efficacy of an age-specific diabetes prevention program in young adults with prediabetes. A one-group pretest-posttest design was used. The inclusion criteria were age 18 to 29 years and the presence of prediabetes (either impaired fasting glucose of 100-125 mg/dL [5.55-6.94 mmol/L] or A1C of 5.7%-6.4%). Fifteen participants were enrolled in the study. A technology-based lifestyle coaching program focused on diet and physical activity and incorporating a handheld device and digital platforms was developed and tested. Psychosocial factors (health literacy, illness perception, self-efficacy, therapeutic efficacy) based on social cognitive theory, changes in diet and physical activity, and cardiometabolic risk factors were assessed at baseline and week 12 after the intervention. A paired-samples t test was performed to examine changes between baseline and postintervention on each psychosocial and physical variable. Participants' (n = 13 completers) mean age was 24.4 ± 2.2 years, 23.1% were male, and 53.8% were African American. Overall, the participants were satisfied with the intervention (mean score, 4.15 on a 5-point, Likert-type scale). Between pre- and posttesting, mean body mass index and mean A1C decreased from 41.0 ± 7.3 kg/m(2) and 6.0 ± 0.5% to 40.1 ± 7.0 kg/m(2) and 5.6 ± 0.5%, respectively, whereas mean fasting glucose did not significantly change (from 92.6 ± 11 to 97.6 ± 14.3 mg/dL [5.14 ± 0.61 to 5.42 ± 0.79 mmol/L]). The intervention resulted in reduced A1C and a trend toward decreased body mass index in obese sedentary young adults with prediabetes after 12 weeks. Further study through a randomized clinical trial with a longer intervention period is warranted. © 2014 The Author(s).

  7. Graphics of polar figure

    International Nuclear Information System (INIS)

    Macias B, L.R.

    1991-11-01

    The objective of this work, is that starting from a data file coming from a spectra that has been softened, and of the one that have been generated its coordinates to project it in stereographic form, to create the corresponding polar figure making use of the Cyber computer of the ININ by means of the GRAPHOS package. This work only requires a Beta, Fi and Intensity (I) enter data file. It starts of the existence of a softened spectra of which have been generated already with these data, making use of some language that in this case was FORTRAN for the Cyber computer, a program is generated supported in the Graphos package that allows starting of a reading of the Beta, Fi, I file, to generate the points in a stereographic projection and that it culminates with the graph of the corresponding polar figure. The program will request the pertinent information that is wanted to capture in the polar figure just as: date, name of the enter file, indexes of the polar figure, number of levels, radio of the stereographic projection (cms.), crystalline system to which belongs the sample, name the neuter graph file by create and to add the own general data. (Author)

  8. Baryon spectroscopy with polarization observables from CLAS

    Energy Technology Data Exchange (ETDEWEB)

    Strauch, Steffen [Univ. of South Carolina, Columbia, SC (United States)

    2016-08-01

    Meson photoproduction is an important tool in the study of baryon resonances. The spectrum of broad and overlapping nucleon excitations can be greatly clarified by use of polarization observables. The N* program at Jefferson Lab with the CEBAF Large Acceptance Spectrometer (CLAS) includes experimental studies with linearly and circularly polarized tagged photon beams, longitudinally and transversely polarized nucleon targets, and recoil polarizations. An overview of these experimental studies and recent results will be given.

  9. Wide-band Polarization Splitter and Rotator with Large Fabrication Tolerance and Simple Fabrication Process

    DEFF Research Database (Denmark)

    Ding, Yunhong; Ou, Haiyan; Peucheret, Christophe

    2013-01-01

    We demonstrate a polarization splitter and rotator built on the silicon-on-insulator platform. The device shows low insertion loss (0.6 dB), low polarization crosstalk (<-12 dB), wide bandwidth (~100 nm), and large fabrication tolerance (60 nm).......We demonstrate a polarization splitter and rotator built on the silicon-on-insulator platform. The device shows low insertion loss (0.6 dB), low polarization crosstalk (fabrication tolerance (60 nm)....

  10. Polar low monitoring

    Science.gov (United States)

    Bobylev, Leonid; Zabolotskikh, Elizaveta; Mitnik, Leonid

    2010-05-01

    Polar lows are intense mesoscale atmospheric low pressure weather systems, developing poleward of the main baroclinic zone and associated with high surface wind speeds. Small size and short lifetime, sparse in-situ observations in the regions of their development complicate polar low study. Our knowledge of polar lows and mesocyclones has come almost entirely during the period of satellite remote sensing since, by virtue of their small horizontal scale, it was rarely possible to analyse these lows on conventional weather charts using only the data from the synoptic observing network. However, the effects of intense polar lows have been felt by coastal communities and seafarers since the earliest times. These weather systems are thought to be responsible for the loss of many small vessels over the centuries, although the nature of the storms was not understood and their arrival could not be predicted. The actuality of the polar low research is stipulated by their high destructive power: they are a threat to such businesses as oil and gas exploration, fisheries and shipping. They could worsen because of global warming: a shrinking of sea ice around the North Pole, which thawed to its record minimum in the summer of 2007, is likely to give rise to more powerful storms that form only over open water and can cause hurricane-strength winds. Therefore, study of polar lows, their timely detection, tracking and forecasting represents a challenge for today meteorology. Satellite passive microwave data, starting from Special Sensor Microwave Imager (SSM/I) onboard Defense Meteorological Satellite Program (DMSP) satellite, remain invaluable source of regularly available remotely sensed data to study polar lows. The sounding in this spectral range has several advantages in comparison with observations in visible and infrared ranges and Synthetic Aperture Radar (SAR) data: independence on day time and clouds, regularity and high temporal resolution in Polar Regions. Satellite

  11. Front-end conceptual platform modeling

    DEFF Research Database (Denmark)

    Guðlaugsson, Tómas Vignir; Ravn, Poul Martin; Mortensen, Niels Henrik

    2014-01-01

    Platform thinking has been the subject of investigation and deployment in many projects in both academia and industry. Most contributions involve the restructuring of product programs, and only a few support front-end development of a new platform in parallel with technology development. This con......Platform thinking has been the subject of investigation and deployment in many projects in both academia and industry. Most contributions involve the restructuring of product programs, and only a few support front-end development of a new platform in parallel with technology development....... The conclusion is that the Conceptual Product Platform model supports stakeholders in achieving an overview of the development tasks and communicating these across multidisciplinary development teams, as well as making decisions on the contents of the platform and providing a link between technical solutions...

  12. Promoting Diversity Through Polar Interdisciplinary Coordinated Education (Polar ICE)

    Science.gov (United States)

    McDonnell, J. D.; Hotaling, L. A.; Garza, C.; Van Dyk, P. B.; Hunter-thomson, K. I.; Middendorf, J.; Daniel, A.; Matsumoto, G. I.; Schofield, O.

    2017-12-01

    Polar Interdisciplinary Coordinated Education (ICE) is an education and outreach program designed to provide public access to the Antarctic and Arctic regions through polar data and interactions with the scientists. The program provides multi-faceted science communication training for early career scientists that consist of a face-to face workshop and opportunities to apply these skills. The key components of the scientist training workshop include cultural competency training, deconstructing/decoding science for non-expert audiences, the art of telling science stories, and networking with members of the education and outreach community and reflecting on communication skills. Scientists partner with educators to provide professional development for K-12 educators and support for student research symposia. Polar ICE has initiated a Polar Literacy initiative that provides both a grounding in big ideas in polar science and science communication training designed to underscore the importance of the Polar Regions to the public while promoting interdisciplinary collaborations between scientists and educators. Our ultimate objective is to promote STEM identity through professional development of scientists and educators while developing career awareness of STEM pathways in Polar science.

  13. The BIRD payload platform

    Science.gov (United States)

    Walter, Ingo; Briess, Klaus; Baerwald, Wolfgang; Skrbek, Wolfgang; Schrandt, Fredrich

    2003-04-01

    For hot spot events as forest fires, volcanic activity or burning oil spills and coal seams a dedicate dspace instrumentation does not exist. With its successful launch end of October 2001 with the Indian Polar Satellite Launch Vehicle the German Aerospace Center starts closing this gap with the micro-satellite mission BIRD. As space segment serves a three-axis stabilized satellite of 92 kg including a contingent of over 30% for the scientific instruments. The main payload of the BIRD micro-satellite is the newly developed Hot Spot Recognition System. It's a dual-channel instrument for middle and thermal IR imagery based on cooled MCT line detectors. The miniaturization by integrated detector/cooler assemblies provides a highly efficient design. A complement for the hot spot detection is the wide-angle stereo-scanner WAOSS-B. It is a hardware re-use dedicated to vegetation and cloud assessment in the visible spectral range. Besides the main objective of hot spot detection the mission has to answer several technological questions of the operation of cooled detectors in space, special aspects of their adaptation to the satellite platform as well as their calibration.

  14. BISIP I: A program for Bayesian inference of spectral induced polarization parameters, and application to mineral exploration at the Canadian Malartic gold deposit, Québec, CA

    Science.gov (United States)

    Lafrenière-Bérubé, Charles; Chouteau, Michel; Shamsipour, Pejman; Olivo, Gema R.

    2016-04-01

    Spectral induced polarization (SIP) parameters can be extracted from field or laboratory complex resistivity measurements, and even airborne or ground frequency domain electromagnetic data. With the growing interest in application of complex resistivity measurements to environmental and mineral exploration problems, there is a need for accurate and easy-to-use inversion tools to estimate SIP parameters. These parameters, which often include chargeability and relaxation time may then be studied and related to other rock attributes such as porosity or metallic grain content, in the case of mineral exploration. We present an open source program, available both as a standalone application or Python module, to estimate SIP parameters using Markov-chain Monte Carlo (MCMC) sampling. The Python language is a high level, open source language that is now widely used in scientific computing. Our program allows the user to choose between the more common Cole-Cole (Pelton), Dias, or Debye decomposition models. Simple circuits composed of resistances and constant phase elements may also be used to represent SIP data. Initial guesses are required when using more classic inversion techniques such as the least-squares formulation, and wrong estimates are often the cause of bad curve fitting. In stochastic optimization using MCMC, the effect of the starting values disappears as the simulation proceeds. Our program is then optimized to do batch inversion over large data sets with as little user-interaction as possible. Additionally, the Bayesian formulation allows the user to do quality control by fully propagating the measurement errors in the inversion process, providing an estimation of the SIP parameters uncertainty. This information is valuable when trying to relate chargeability or relaxation time to other physical properties. We test the inversion program on complex resistivity measurements of 12 core samples from the world-class gold deposit of Canadian Malartic. Results show

  15. Strategic Polarization.

    Science.gov (United States)

    Kalai, Adam; Kalai, Ehud

    2001-08-01

    In joint decision making, similarly minded people may take opposite positions. Consider the example of a marriage in which one spouse gives generously to charity while the other donates nothing. Such "polarization" may misrepresent what is, in actuality, a small discrepancy in preferences. It may be that the donating spouse would like to see 10% of their combined income go to charity each year, while the apparently frugal spouse would like to see 8% donated. A simple game-theoretic analysis suggests that the spouses will end up donating 10% and 0%, respectively. By generalizing this argument to a larger class of games, we provide strategic justification for polarization in many situations such as debates, shared living accommodations, and disciplining children. In some of these examples, an arbitrarily small disagreement in preferences leads to an arbitrarily large loss in utility for all participants. Such small disagreements may also destabilize what, from game-theoretic point of view, is a very stable equilibrium. Copyright 2001 Academic Press.

  16. MobiNet: a pedagogic platform for Computer Science, Maths and Physics (How to make students love Maths by programming video games)

    OpenAIRE

    Lefebvre , Sylvain; Neyret , Fabrice; Hornus , Samuel; Thollot , Joëlle

    2004-01-01

    International audience; We developed the MobiNet (free) platform and tutorial sessions (tested on 16 batches of high school students) with the aim of offering students a new way of learning and understanding academic scientific subjects. Our approach consists of letting the students manipulate mathematical and physical notions as tools in order to solve concrete tasks, such as a solar system simulation or a video game. This makes students formalize a realworld problem, experiment by trial-and...

  17. HipMatch: an object-oriented cross-platform program for accurate determination of cup orientation using 2D-3D registration of single standard X-ray radiograph and a CT volume.

    Science.gov (United States)

    Zheng, Guoyan; Zhang, Xuan; Steppacher, Simon D; Murphy, Stephen B; Siebenrock, Klaus A; Tannast, Moritz

    2009-09-01

    The widely used procedure of evaluation of cup orientation following total hip arthroplasty using single standard anteroposterior (AP) radiograph is known inaccurate, largely due to the wide variability in individual pelvic orientation relative to X-ray plate. 2D-3D image registration methods have been introduced for an accurate determination of the post-operative cup alignment with respect to an anatomical reference extracted from the CT data. Although encouraging results have been reported, their extensive usage in clinical routine is still limited. This may be explained by their requirement of a CAD model of the prosthesis, which is often difficult to be organized from the manufacturer due to the proprietary issue, and by their requirement of either multiple radiographs or a radiograph-specific calibration, both of which are not available for most retrospective studies. To address these issues, we developed and validated an object-oriented cross-platform program called "HipMatch" where a hybrid 2D-3D registration scheme combining an iterative landmark-to-ray registration with a 2D-3D intensity-based registration was implemented to estimate a rigid transformation between a pre-operative CT volume and the post-operative X-ray radiograph for a precise estimation of cup alignment. No CAD model of the prosthesis is required. Quantitative and qualitative results evaluated on cadaveric and clinical datasets are given, which indicate the robustness and the accuracy of the program. HipMatch is written in object-oriented programming language C++ using cross-platform software Qt (TrollTech, Oslo, Norway), VTK, and Coin3D and is transportable to any platform.

  18. Precessing deuteron polarization

    International Nuclear Information System (INIS)

    Sitnik, I.M.; Volkov, V.I.; Kirillov, D.A.; Piskunov, N.M.; Plis, Yu.A.

    2002-01-01

    The feasibility of the acceleration in the Nuclotron of deuterons polarized in the horizontal plane is considered. This horizontal polarization is named precessing polarization. The effects of the main magnetic field and synchrotron oscillations are included. The precessing polarization is supposed to be used in studying the polarization parameters of the elastic dp back-scattering and other experiments

  19. Drilling Polar Oceans with the European Research Icebreaker AURORA BOREALIS: the IODP Context

    Science.gov (United States)

    Lembke-Jene, Lester; Wolff-Boenisch, Bonnie; Azzolini, Roberto; Thiede, Joern; Biebow, Nicole; Eldholm, Olav; Egerton, Paul

    2010-05-01

    -European partners), a multidisciplinary platform for studies ranging from the sub-seafloor into the atmosphere. AURORA BOREALIS was planned for her role in deep-sea drilling in consultation with engineers and technical experts familiar with the program and the operation of these vessels. All techniques currently deployed on IODP expeditions can be implemented onboard the vessel under polar weather and ice conditions, including the full range of re-entry, casing and cementing, and instrumentation options and the entire suite of downhole logging tools. Due to sufficient laboratory space, a full analytical workflow can be easily established comparable to existing permanent platforms, including clean rooms, diverse scanning and logging or incubation facilities. While the vessel is equipped with a dedicated deep-sea drilling rig, other coring and drilling techniques can be employed if needed (e.g. Rockdrill, MEBO, large diameter Kasten cores). AURORA BOREALIS is fitted to operate a CALYPSO Piston Coring System in polar waters. Future mud-return systems under consideration and testing for IODP to provide controlled borehole conditions in difficult facies are compatible with the layout of AURORA BOREALIS. The berthing capacity of 120 personnel total (scientists, technical support and crew) allows to accommodate a sufficient number of science party members offshore. The present scientific implementation documents plan for about one polar scientific drilling expedition per year in a to-be-determined configuration. As the vessel is a multi-dsiciplinary platform, operations for the entire year are not dependant on drilling operations alone. While principal access to the vessel will be based on a competitive proposal review and evaluation system, the allocation of timeslots specifically for drilling would preferably be given over to IODP handling and planning systems in a cooperative mode using the strengths and capacitites of the future program. Depending on interests and needs of the

  20. Mobile platform security

    CERN Document Server

    Asokan, N; Dmitrienko, Alexandra

    2013-01-01

    Recently, mobile security has garnered considerable interest in both the research community and industry due to the popularity of smartphones. The current smartphone platforms are open systems that allow application development, also for malicious parties. To protect the mobile device, its user, and other mobile ecosystem stakeholders such as network operators, application execution is controlled by a platform security architecture. This book explores how such mobile platform security architectures work. We present a generic model for mobile platform security architectures: the model illustrat

  1. Polare maskuliniteter

    Directory of Open Access Journals (Sweden)

    Marit Anne Hauan

    2012-05-01

    Full Text Available In this paper my aim is to read and understand the journal of Gerrit de Veer from the last journey of William Barents to the Arctic Regions in 1596 and the journal of captain Junge on his hunting trip from Tromsø to Svalbard in 1834.It is nearly 240 years between this to voyages. The first journal is known as the earliest report from the arctic era. Gerrit de Veer adds instructive copper engravings to his text and give us insight in the crews meeting with this new land. Captain Junges journal is found together with his dead crew in a house in a fjord nearby Ny-Ålesund and has no drawings, but word. Both of these journals may be read as sources of the knowledge and understanding of the polar region. They might also unveil the ideas of how to deal with and survive under the challenges that is given. In addition one can ask if the sources can tell us more about how men describe their challenges. Can the way they expressed themselves in the journals give us an understanding of masculinity? And not least help us to create good questions of the change in the ideas of masculinities which is said to follow the change in understanding of the wilderness.

  2. ITS Platform North Denmark

    DEFF Research Database (Denmark)

    Lahrmann, Harry; Agerholm, Niels; Juhl, Jens

    2012-01-01

    This paper presents the project entitled “ITS Platform North Denmark” which is used as a test platform for Intelligent Transportation System (ITS) solutions. The platform consists of a newly developed GNSS/GPRS On Board Unit (OBU) to be installed in 500 cars, a backend server and a specially...

  3. Cross-Platform Technologies

    Directory of Open Access Journals (Sweden)

    Maria Cristina ENACHE

    2017-04-01

    Full Text Available Cross-platform - a concept becoming increasingly used in recent years especially in the development of mobile apps, but this consistently over time and in the development of conventional desktop applications. The notion of cross-platform software (multi-platform or platform-independent refers to a software application that can run on more than one operating system or computing architecture. Thus, a cross-platform application can operate independent of software or hardware platform on which it is execute. As a generic definition presents a wide range of meanings for purposes of this paper we individualize this definition as follows: we will reduce the horizon of meaning and we use functionally following definition: a cross-platform application is a software application that can run on more than one operating system (desktop or mobile identical or in a similar way.

  4. PyGaze: an open-source, cross-platform toolbox for minimal-effort programming of eye-tracking experiments

    NARCIS (Netherlands)

    Dalmaijer, E.S.; Mathôt, S.; van der Stigchel, S.|info:eu-repo/dai/nl/29880977X

    2014-01-01

    he PyGaze toolbox is an open-source software package for Python, a high-level programming language. It is designed for creating eyetracking experiments in Python syntax with the least possible effort, and it offers programming ease and script readability without constraining functionality and

  5. Physics results with polarized electrons at SLAC

    International Nuclear Information System (INIS)

    Prescott, C.Y.

    1996-03-01

    Polarized electron beams can play an important role in the dynamics of interactions at high energies. Polarized electron beams at SLAC have been an important part of the physics program since 1970, when they were first proposed for use in testing the spin structure of the proton. Since 1992, the SLAC linear accelerator and the SLC have operated solely with polarized electrons, providing data for tests of QCD in studies of the spin structure of the nucleon and tests of the electroweak sector of the Standard Model. In the following sections, the performance of the source is summarized, and some of the recent results using the polarized beams are discussed

  6. Polarized electron sources

    Energy Technology Data Exchange (ETDEWEB)

    Prepost, R. [Univ. of Wisconsin, Madison, WI (United States)

    1994-12-01

    The fundamentals of polarized electron sources are described with particular application to the Stanford Linear Accelerator Center. The SLAC polarized electron source is based on the principle of polarized photoemission from Gallium Arsenide. Recent developments using epitaxially grown, strained Gallium Arsenide cathodes have made it possible to obtain electron polarization significantly in excess of the conventional 50% polarization limit. The basic principles for Gallium and Arsenide polarized photoemitters are reviewed, and the extension of the basic technique to strained cathode structures is described. Results from laboratory measurements of strained photocathodes as well as operational results from the SLAC polarized source are presented.

  7. AutoCAD platform customization VBA

    CERN Document Server

    Ambrosius, Lee

    2015-01-01

    Boost productivity and streamline your workflow with expert AutoCAD: VBA programming instruction AutoCAD Platform Customization: VBA is the definitive guide to personalizing AutoCAD and the various programs that run on the AutoCAD platform, including AutoCAD Architecture, Civil 3D, Plant 3D, and more. Written by an Autodesk insider with years of customization and programming experience, this book features detailed discussions backed by real-world examples and easy-to-follow tutorials that illustrate each step in the personalization process. Readers gain expert guidance toward managing layout

  8. AutoCAD platform customization autolisp

    CERN Document Server

    Ambrosius, Lee

    2014-01-01

    Customize and personalize programs built on the AutoCAD platform AutoLISP is the key to unlocking the secrets of a more streamlined experience using industry leading software programs like AutoCAD, Civil 3D, Plant 3D, and more. AutoCAD Platform Customization: AutoLISP provides real-world examples that show you how to do everything from modifying graphical objects and reading and setting system variables to communicating with external programs. It also features a resources appendix and downloadable datasets and customization examples-tools that ensure swift and easy adoption. Find out how to r

  9. Product Platform Modeling

    DEFF Research Database (Denmark)

    Pedersen, Rasmus

    on the notion that reuse and encapsulation of platform elements are fundamental characteristics of a product platform. Reuse covers the desire to reuse and share certain assets across a family of products and/or across generations of products. Product design solutions and principles are often regarded...... as important assets in a product platform, yet activities, working patterns, processes and knowledge can also be reused in a platform approach. Encapsulation is seen as a process in which the different elements of a platform are grouped into well defined and self-contained units which are decoupled from each...... support decision makers during a product platform project. The reaction from stakeholders in the case companies indicates that the decision base is improved by means of visual models. Another finding is that the sometimes rather theoretical and intangible phenomena can be instantiated in models...

  10. Continuous Platform Development

    DEFF Research Database (Denmark)

    Nielsen, Ole Fiil

    evolution does not make the platforms irrelevant. This research is based on case studies and applications in the two Danish companies, LEGO and Grundfos, where several platform development projects have been followed. LEGO is exceptional for their long experience with platform development and maintenance......, while Grundfos is relatively new within this area. This study puts emphasis on platform projects and defines such projects as something very different from product development projects and more similar to industrial research projects, due to the fact that they are continuous activities with relatively...... low risks and investments but also with relatively fuzzy results. When looking for new platform projects, it is important to make sure that the company and market is ready for the introduction of platforms, and to make sure that people from marketing and sales, product development, and downstream...

  11. ADMS Evaluation Platform

    Energy Technology Data Exchange (ETDEWEB)

    2018-01-23

    Deploying an ADMS or looking to optimize its value? NREL offers a low-cost, low-risk evaluation platform for assessing ADMS performance. The National Renewable Energy Laboratory (NREL) has developed a vendor-neutral advanced distribution management system (ADMS) evaluation platform and is expanding its capabilities. The platform uses actual grid-scale hardware, large-scale distribution system models, and advanced visualization to simulate realworld conditions for the most accurate ADMS evaluation and experimentation.

  12. Currency trading platform

    OpenAIRE

    DEL BARRIO ALBELDA, ALBERTO

    2015-01-01

    This project aims to build a web platform for intra day currency investors. Using the platform a trader is able to place orders, in real time, in the btc-e.com exchange, view the state of his wallet, look over the past orders and transactions, check the balance of his account, etc. The project fetches, stores, analyzes and transforms the information provided by the API of the exchange. The platform enhances and adds functionality to basic operations provided by the exchan...

  13. Formal behavioral evaluation of enrichment programs on a zookeeper's schedule: a case study with a polar bear (Ursus Maritimus) at the Bronx Zoo.

    Science.gov (United States)

    Canino, Wendy; Powell, David

    2010-01-01

    We conducted a brief study of the effectiveness of environmental enrichment for a polar bear at the Bronx Zoo with two objectives in mind. First we wanted to determine if a novel method of collecting data that easily fits into a zookeeper's work routine would produce usable data and if so, we wanted to evaluate the effectiveness of some new items that had been purchased for enriching the polar bear in reducing his pacing behavior. Observations were recorded for 119 days over a period of 5 months from April 2007 through August 2007. Five new items and eight previously used items were rotated and presented to the polar bear in the morning and afternoon. We recorded the bear's behavior five times per day as we passed by his exhibit during our regular work routine. Predictably, we found that the newer enrichment items were more effective at increasing play and decreasing pacing, as well as other more subtle effects on his behavior that helped us to design a better enrichment routine. More importantly, we found that this method of "multi-point scan sampling" was effective at producing ample and reliable data that could be used to analyze the bear's behavior without adding significant work to the keepers' daily routine. (c) 2009 Wiley-Liss, Inc.

  14. Omnidirectional holonomic platforms

    International Nuclear Information System (INIS)

    Pin, F.G.; Killough, S.M.

    1994-01-01

    This paper presents the concepts for a new family of wheeled platforms which feature full omnidirectionality with simultaneous and independently controlled rotational and translational motion capabilities. The authors first present the orthogonal-wheels concept and the two major wheel assemblies on which these platforms are based. They then describe how a combination of these assemblies with appropriate control can be used to generate an omnidirectional capability for mobile robot platforms. The design and control of two prototype platforms are then presented and their respective characteristics with respect to rotational and translational motion control are discussed

  15. Platform decommissioning costs

    International Nuclear Information System (INIS)

    Rodger, David

    1998-01-01

    There are over 6500 platforms worldwide contributing to the offshore oil and gas production industry. In the North Sea there are around 500 platforms in place. There are many factors to be considered in planning for platform decommissioning and the evaluation of options for removal and disposal. The environmental impact, technical feasibility, safety and cost factors all have to be considered. This presentation considers what information is available about the overall decommissioning costs for the North Sea and the costs of different removal and disposal options for individual platforms. 2 figs., 1 tab

  16. Miniaturized Retrodirective Arrays for a Nanosatellite Platform

    Science.gov (United States)

    2012-01-01

    Miniaturized Retrodirective Arrays for a Nanosatellite Platform NIA Sb. GRANT NUMBER N00014-1 0-1-0056 Sc. PROGRAM ELEMENT NUMBER . NIA 6. AUTHOR(S) Sd...into a mobile platfonn, such as a nanosatellite , presents unique challenges due to the platform’s restrictions in terms of size, weight, and power...of power detection and null scanning. 1S. SUBJECT TERMS Retrodirective Array, Nanosatellite 16. SECURITY CLASSIFICATION OF: a. REPORT b. ABSTRACT

  17. Polarization-insensitive wavelength conversion of 40 Gb/s NRZ-DPSK signals in a silicon polarization diversity circuit

    DEFF Research Database (Denmark)

    Vukovic, Dragana; Ding, Yunhong; Hu, Hao

    2014-01-01

    Polarization insensitive wavelength conversion of a 40 Gb/s non-return-to-zero (NRZ) differential phase-shift keying (DPSK) data signal is demonstrated using four-wave mixing (FWM) in a silicon nanowire circuit. Polarization independence is achieved using a diversity circuit based on polarization...... rotators and splitters, which is fabricated by a simple process on the silicon-on-insulator (SOI) platform. Error-free performance is achieved with only 0.5 dB of power penalty compared to the wavelength conversion of a signal with well optimized input polarization. Additionally, data transmission over 161...

  18. Ross Sea oceanographic data, 1983-1987 : USCGC Glacier, January-February 1983; USCGC Polar Sea, January-February 1984; USCGC Polar Star, February 1985; USCGC Polar Sea, February 1987 (NODC Accession 8900108)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Temperature profile and chemical data were collected using CTD casts from USCGC POLAR SEA and other platforms in the Ross Sea from 19 December 1976 to 06 February...

  19. A Proposal to the Department of Energy for The Fabrication of a Very High Energy Polarized Gama Ray Beam Facility and A Program of Medium Energy Physics Research at The National Synchrotron Light Source

    Energy Technology Data Exchange (ETDEWEB)

    Sandorfi, A.M.; LeVine, M.J.; Thorn, C.E.; Giordano, G.; Matone, G.

    1982-09-01

    This proposal requests support for the fabrication and operation of a modest facility that would provide relatively intense beams of monochromatic and polarized photons with energies in the range of several hundreds of MeV. These {gamma} rays would be produced by Compton backscattering laser light from the electrons circulating in the 2.5-3.0 GeV 'X-RAY' storage ring of the National Synchrotron Light Source (NSLS) at Brookhaven National Laboratory. The excellent emittance, phase space, and high current of this state-of-the-art storage ring will allow the production of 2 x 10{sup 7} {gamma} rays per second. These photons would be tagged by detecting the scattered electrons, thereby determining the energy to 2.7 MeV for all {gamma}-ray energies. The efficiency of this tagging procedure is 100% and the {gamma}-ray beam would be essentially background free. Tagging will also allow the flexibility of operating with a dynamic range as large as 200 MeV in photon energy while still preserving high resolution and polarization. These beams will permit a fruitful study of important questions in medium-energy nuclear physics. The initial goals of this program are to reach reliable operation with photon energies up to 300 MeV and to develop {gamma}-ray beams with energies up to about 500 MeV. To demonstrate reliable operation, a modest physics program is planned that, for the most part, utilizes existing magnets and detector systems but nonetheless addresses several important outstanding problems. Gamma ray beams of the versatility, intensity, energy, and resolution that can be achieved at this facility are not currently available at any other world facility either existing or under construction. Furthermore, the proposed program would produce the first intense source of medium-energy {gamma} rays that are polarized. Because of the difficulties in producing such polarized beams, it is very unlikely that viable alternate sources can be developed in the near future; at

  20. Analysis of ex vivo drug response data of Plasmodium clinical isolates: the pros and cons of different computer programs and online platforms.

    Science.gov (United States)

    Wirjanata, Grennady; Handayuni, Irene; Zaloumis, Sophie G; Chalfein, Ferryanto; Prayoga, Pak; Kenangalem, Enny; Poespoprodjo, Jeanne Rini; Noviyanti, Rintis; Simpson, Julie A; Price, Ric N; Marfurt, Jutta

    2016-03-02

    In vitro drug susceptibility testing of malaria parasites remains an important component of surveillance for anti-malarial drug resistance. The half-maximal inhibition of growth (IC50) is the most commonly reported parameter expressing drug susceptibility, derived by a variety of statistical approaches, each with its own advantages and disadvantages. In this study, licensed computer programs WinNonlin and GraphPad Prism 6.0, and the open access programs HN-NonLin, Antimalarial ICEstimator (ICE), and In Vitro Analysis and Reporting Tool (IVART) were tested for their ease of use and ability to estimate reliable IC50 values from raw drug response data from 31 Plasmodium falciparum and 29 P. vivax clinical isolates tested with five anti-malarial agents: chloroquine, amodiaquine, piperaquine, mefloquine, and artesunate. The IC50 and slope estimates were similar across all statistical packages for all drugs tested in both species. There was good correlation of results derived from alternative statistical programs and non-linear mixed-effects modelling (NONMEM) which models all isolate data simultaneously. The user-friendliness varied between packages. While HN-NonLin and IVART allow users to enter the data in 96-well format, IVART and GraphPad Prism 6.0 are capable to analyse multiple isolates and drugs in parallel. WinNonlin, GraphPad Prism 6.0, IVART, and ICE provide alerts for non-fitting data and incorrect data entry, facilitating data interpretation. Data analysis using WinNonlin or ICE took the longest computationally, whilst the offline ability of GraphPad Prism 6.0 to analyse multiple isolates and drugs simultaneously made it the fastest among the programs tested. IC50 estimates obtained from the programs tested were comparable. In view of processing time and ease of analysis, GraphPad Prism 6.0 or IVART are best suited for routine and large-scale drug susceptibility testing.

  1. Graphics of polar figure; Graficado de figura polar

    Energy Technology Data Exchange (ETDEWEB)

    Macias B, L.R

    1991-11-15

    The objective of this work, is that starting from a data file coming from a spectra that has been softened, and of the one that have been generated its coordinates to project it in stereographic form, to create the corresponding polar figure making use of the Cyber computer of the ININ by means of the GRAPHOS package. This work only requires a Beta, Fi and Intensity (I) enter data file. It starts of the existence of a softened spectra of which have been generated already with these data, making use of some language that in this case was FORTRAN for the Cyber computer, a program is generated supported in the Graphos package that allows starting of a reading of the Beta, Fi, I file, to generate the points in a stereographic projection and that it culminates with the graph of the corresponding polar figure. The program will request the pertinent information that is wanted to capture in the polar figure just as: date, name of the enter file, indexes of the polar figure, number of levels, radio of the stereographic projection (cms.), crystalline system to which belongs the sample, name the neuter graph file by create and to add the own general data. (Author)

  2. Poly(3,4-ethylenedioxythiophene)-Based Nanofiber Mats as an Organic Bioelectronic Platform for Programming Multiple Capture/Release Cycles of Circulating Tumor Cells.

    Science.gov (United States)

    Yu, Chia-Cheng; Ho, Bo-Cheng; Juang, Ruey-Shin; Hsiao, Yu-Sheng; Naidu, R Venkata Ram; Kuo, Chiung-Wen; You, Yun-Wen; Shyue, Jing-Jong; Fang, Ji-Tseng; Chen, Peilin

    2017-09-13

    In this investigation, we employed a novel one-step electrospinning process to fabricate poly(ethylene oxide) (PEO)/poly(3,4-ethylenedioxythiophene):polystyrenesulfonate (PEDOT:PSS) core/shell nanofiber structures with improved water resistance and good electrochemical properties and characterized them using scanning electron microscopy, transmission electron microscopy, and time-of-flight secondary ion mass spectrometry imaging. We then integrated a biotinylated poly-(l-lysine-graft-ethylene glycol) (PLL-g-PEG-biotin) coating with three-dimensional (3D) PEDOT-based nanofiber devices for dynamic control over the capture/release performance of rare circulating tumor cells (CTCs) on-chip. The detailed capture/release behavior of the circulating tumor cells was studied using an organic bioelectronic platform comprising PEO/PEDOT:PSS nanofiber mats with 3 wt % (3-glycidyloxypropyl)trimethoxysilane as an additive. We have demonstrated that these nanofiber mats deposited on five-patterned indium tin oxide finger electrodes are excellent candidates for use as functional bioelectronic interfaces for the isolation, detection, sequential collection, and enrichment of rare CTCs through electrical activation of each single electrode. This combination behaved as an ideal model system displaying a high cell-capture yield for antibody-positive cells while resisting the adhesion of antibody-negative cells. Taking advantage of the electrochemical doping/dedoping characteristics of PEDOT:PSS materials, the captured rare cells could be electrically triggered release through the desorption phenomena of PLL-g-PEG-biotin on device surface. More than 90% of the targeted cancer cells were captured on the 3D PEDOT-based nanofiber microfluidic device; over 87% of captured cancer cells were subsequently released for collection; approximately 80% of spiked cancer cells could be collected in a 96-well plate. Therefore, this 3D PEDOT-based nanofiber approach appears to be an economical route

  3. Platform development supportedby gaming

    DEFF Research Database (Denmark)

    Mikkola, Juliana Hsuan; Hansen, Poul H. Kyvsgård

    2007-01-01

    , possibly increasing the strategic risks for the firm. This paper reports preliminary findings on platform management process at LEGO, a Danish toy company.  Specifically, we report the process of applying games combined with simulations and workshops in the platform development. We also propose a framework...

  4. Groundwater Assessment Platform

    OpenAIRE

    Podgorski, Joel; Berg, Michael

    2018-01-01

    The Groundwater Assessment Platform is a free, interactive online GIS platform for the mapping, sharing and statistical modeling of groundwater quality data. The modeling allows users to take advantage of publicly available global datasets of various environmental parameters to produce prediction maps of their contaminant of interest.

  5. RHIC FY15 pp Run RHIC and AGS polarization analysis

    Energy Technology Data Exchange (ETDEWEB)

    Huang, H. [Brookhaven National Lab. (BNL), Upton, NY (United States); Adams, P. [Brookhaven National Lab. (BNL), Upton, NY (United States)

    2016-02-20

    The polarization information is important for the spin physics program in Relativistic Heavy Ion Collider (RHIC). There are discrepancies between AGS and RHIC polarization measurements. First, the face value of AGS polarization is higher than RHIC ones in general. Second, the measured polarization profile (described by the profile ratio R) is stronger in AGS than in RHIC. This note analyzes the polarization data from FY15 pp run period. The results show that the differences between AGS and RHIC polarization measurements are reasonable, but the R value difference is puzzling. The difference between blue and yellow ring is worth of spin simulation to explain.

  6. Product Platform Replacements

    DEFF Research Database (Denmark)

    Sköld, Martin; Karlsson, Christer

    2012-01-01

    . To shed light on this unexplored and growing managerial concern, the purpose of this explorative study is to identify operational challenges to management when product platforms are replaced. Design/methodology/approach – The study uses a longitudinal field-study approach. Two companies, Gamma and Omega......Purpose – It is argued in this article that too little is known about product platforms and how to deal with them from a manager's point of view. Specifically, little information exists regarding when old established platforms are replaced by new generations in R&D and production environments...... distinguishing between platform replacement “height” and “width”. Seven groups of managerial measures for dealing with the issues are recommended. Originality/value – The study aims to contribute to the existing literature by taking a managers' perspective of product platform development. Its specific...

  7. Geographical Income Polarization

    DEFF Research Database (Denmark)

    Azhar, Hussain; Jonassen, Anders Bruun

    inter municipal income inequality. Counter factual simulations show that rising property prices to a large part explain the rise in polarization. One side-effect of polarization is tendencies towards a parallel polarization of residence location patterns, where low skilled individuals tend to live......In this paper we estimate the degree, composition and development of geographical income polarization based on data at the individual and municipal level in Denmark from 1984 to 2002. Rising income polarization is reconfirmed when applying new polarization measures, the driving force being greater...

  8. The COMPASS study: a longitudinal hierarchical research platform for evaluating natural experiments related to changes in school-level programs, policies and built environment resources.

    Science.gov (United States)

    Leatherdale, Scott T; Brown, K Stephen; Carson, Valerie; Childs, Ruth A; Dubin, Joel A; Elliott, Susan J; Faulkner, Guy; Hammond, David; Manske, Steve; Sabiston, Catherine M; Laxer, Rachel E; Bredin, Chad; Thompson-Haile, Audra

    2014-04-08

    Few researchers have the data required to adequately understand how the school environment impacts youth health behaviour development over time. COMPASS is a prospective cohort study designed to annually collect hierarchical longitudinal data from a sample of 90 secondary schools and the 50,000+ grade 9 to 12 students attending those schools. COMPASS uses a rigorous quasi-experimental design to evaluate how changes in school programs, policies, and/or built environment (BE) characteristics are related to changes in multiple youth health behaviours and outcomes over time. These data will allow for the quasi-experimental evaluation of natural experiments that will occur within schools over the course of COMPASS, providing a means for generating "practice based evidence" in school-based prevention programming. COMPASS is the first study with the infrastructure to robustly evaluate the impact that changes in multiple school-level programs, policies, and BE characteristics within or surrounding a school might have on multiple youth health behaviours or outcomes over time. COMPASS will provide valuable new insight for planning, tailoring and targeting of school-based prevention initiatives where they are most likely to have impact.

  9. Education and outreach for the International Polar Year

    Science.gov (United States)

    Pfirman, Stephanie; Bell, Robin Elizabeth; Turrin, Margie; Maru, Poonam

    2004-12-01

    If the 65 educators, scientists, and media specialists who gathered at the “Bridging the Poles” workshop in Washington, D.C. last June have their way a semitrailer truck labeled “Got Snow?” would traverse the country during the International Polar Year (IPY) of 2007-2009 loaded with polar gear, interactive activities, and a snowmaker. We would significantly increase the number of Arctic residents—especially indigenous Alaskans—with Ph.D.s. We would build exchange programs between inner city youths and polar residents. Polar exhibitions would open at natural history and art museums and zoos. And polar postage stamps, interactive polar computer games, national polar book-of-the-month recommendations, made-for-TV polar documentaries, and a polar youth forum would bring the poles front and center to the public's attention.

  10. Polarized Light Corridor Demonstrations.

    Science.gov (United States)

    Davies, G. R.

    1990-01-01

    Eleven demonstrations of light polarization are presented. Each includes a brief description of the apparatus and the effect demonstrated. Illustrated are strain patterns, reflection, scattering, the Faraday Effect, interference, double refraction, the polarizing microscope, and optical activity. (CW)

  11. The vacuum platform

    Science.gov (United States)

    McNab, A.

    2017-10-01

    This paper describes GridPP’s Vacuum Platform for managing virtual machines (VMs), which has been used to run production workloads for WLCG and other HEP experiments. The platform provides a uniform interface between VMs and the sites they run at, whether the site is organised as an Infrastructure-as-a-Service cloud system such as OpenStack, or an Infrastructure-as-a-Client system such as Vac. The paper describes our experience in using this platform, in developing and operating VM lifecycle managers Vac and Vcycle, and in interacting with VMs provided by LHCb, ATLAS, ALICE, CMS, and the GridPP DIRAC service to run production workloads.

  12. Ladder attachment platform

    Science.gov (United States)

    Swygert,; Richard, W [Springfield, SC

    2012-08-28

    A ladder attachment platform is provided that includes a base for attachment to a ladder that has first and second side rails and a plurality of rungs that extend between in a lateral direction. Also included is a user platform for having a user stand thereon that is carried by the base. The user platform may be positioned with respect to the ladder so that it is not located between a first plane that extends through the first side rail and is perpendicular to the lateral direction and a second plane that extends through the second side rail and is perpendicular to the lateral direction.

  13. Polarized Moessbauer transitions

    International Nuclear Information System (INIS)

    Barb, D.

    1975-01-01

    Theoretical aspects of the emission, absorption and scattering of polarized gamma rays are reviewed for a general case of combined magnetic and electric hyperfine interactions; various possibilities of obtaining polarized gamma sources are described and examples are given of the applications of Moessbauer spectroscopy with polarized gamma rays in solving problems of solid state physics. (A.K.)

  14. THE VIRTUAL UNIVERSITY MODEL AS THE MAIN PLATFORM FOR IMPLEMENTATION OF PROFESSIONAL RETRAINING PROGRAM FOR TEACHERS BY THE EXMPLE OF SYRIAN VIRTUAL UNIVERSITY

    Directory of Open Access Journals (Sweden)

    K. O. Prosyukova

    2014-09-01

    Full Text Available The interest in virtual education has recently increased in educational environment. Researchers in their scientific activity are focused on the benefits of the “virtual university” or “virtual college” models. But the range of a “virtuality” concept is too wide: some researchers recognize all information technologies in education as virtual means, while the others are looking for the ways to replace education in its general meaning with virtual educational space. The problem of virtual education is also relevant because the application area is boundless: school education, secondary professional education, higher education, training and retraining programs. Thus virtual education is able to become not only the innovative educational model, but also a possible solution to the problem of continuing education. One of the most successful examples in this field is the example of Syrian Virtual University, which has become the pioneer in virtual education in the Middle East region.

  15. ECUT: Energy Conversion and Utilization Technologies program biocatalysis research activity. Potential membrane applications to biocatalyzed processes: Assessment of concentration polarization and membrane fouling

    Science.gov (United States)

    Ingham, J. D.

    1983-01-01

    Separation and purification of the products of biocatalyzed fermentation processes, such as ethanol or butanol, consumes most of the process energy required. Since membrane systems require substantially less energy for separation than most alternatives (e.g., distillation) they have been suggested for separation or concentration of fermentation products. This report is a review of the effects of concentration polarization and membrane fouling for the principal membrane processes: microfiltration, ultrafiltration, reverse osmosis, and electrodialysis including a discussion of potential problems relevant to separation of fermentation products. It was concluded that advanced membrane systems may result in significantly decreased energy consumption. However, because of the need to separate large amounts of water from much smaller amounts of product that may be more volatile than wate, it is not clear that membrane separations will necessarily be more efficient than alternative processes.

  16. Product Platform Performance

    DEFF Research Database (Denmark)

    Munk, Lone

    , and the subject has gained increased attention in industry and academia the past decade. Literature on platform-based product development is often based on single case studies and it is sparsely verified if expected effects are achieved. This makes it difficult to put forward realistic expectations for companies.......e. if the expected results are achieved), and • reasons for possible deviations between these, comparing them to existing platform assessment criteria. The research results are based on 8 comprehensive case studies of product platforms in LEGO Company in the period of 2004-2009 (involving participant observation...... effects. The model empirically verifies findings in literature and received moderate support from industry in the validation study. The research findings document that product platforms achieve significant internal effects in terms of • reduced development time (often around 25 %), • reduced number...

  17. Cellular Sentinels Toxicity Platform

    Science.gov (United States)

    2017-02-01

    Screening hits in red for ENZO cardiotoxicity library tested in the phenotypic and physiology platforms at the indicated incubation times...assay timeline .................................................................................... 34 Figure 27. Automated algorithm detection of...40 Figure 33. Automated algorithm detection of multiplexed dyes for

  18. USA Hire Testing Platform

    Data.gov (United States)

    Office of Personnel Management — The USA Hire Testing Platform delivers tests used in hiring for positions in the Federal Government. To safeguard the integrity of the hiring processes and ensure...

  19. The Creative Platform

    DEFF Research Database (Denmark)

    Byrge, Christian; Hansen, Søren

    whether you consider thirdgrade teaching, human-resource development, or radical new thinking in product development in a company. The Creative Platform was developed at Aalborg University through a series of research-and-development activities in collaboration with educational institutions and private......This book is about introducing more creativity into general educational courses and cross-disciplinary activities. It is directed toward teachers at all levels in the educational system, but the Creative Platform is a general model, and thus the creative process will fundamentally be the same...... companies. It is a project in which the goal is to make a hands-on approach to a knowledge perspective on enhancing creativity. The underlying ambition of the Creative Platform is to make it easier to promote creativity. At www.uka.aau.dk/The+Creative+Platform, you can find extra materials and instructions...

  20. Optical pumping production of spin polarized hydrogen

    International Nuclear Information System (INIS)

    Knize, R.J.; Happer, W.; Cecchi, J.L.

    1984-01-01

    There has been much interest recently in the production of large quantities of spin polarized hydrogen in various fields including controlled fusion, quantum fluids, high energy, and nuclear physics. One promising method for the development of large quantities of spin polarized hydrogen is the utilization of optical pumping with a laser. Optical pumping is a process where photon angular momentum is converted into electron and nuclear spin. The advent of tunable CW dye lasers (approx. 1 watt) allow the production of greater than 10 18 polarized atoms/sec. We have begun a program at Princeton to investigate the physics and technology of using optical pumping to produce large quantities of spin polarized hydrogen. Initial experiments have been done in small closed glass cells. Eventually, a flowing system, open target, or polarized ion source could be constructed

  1. Future European and Japanese remote-sensing sensors and programs; Proceedings of the Meeting, Orlando, FL, Apr. 1, 2, 1991

    Science.gov (United States)

    Slater, Philip N.

    Consideration is given to the METEOSAT second-generation program, the ESA earth observation polar platform program, a new satellite for a climatology study in the tropics, a medium-resolution imaging spectrometer, a Michelson interferometer for passive atmosphere sounding, an optical mapping instrument, an optical sensor system for Japanese earth resources satellite 1, a synthetic aperture radar of JERS-1, an ocean color and temperature scanner for Advanced Earth-Observing Satellite (ADEOS), an interferometric monitor for greenhouse gasses for ADEOS. Attention is also given to Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) for EOS-A, short-wave infrared subsystem design status of ASTER, ASTER calibration concept, Japanese polar orbit platform program, and airborne and spaceborne thermal multispectral remote sensing. (For individual items see A93-20427 to A93-20452)

  2. Calibration platforms for gravimeters

    Science.gov (United States)

    Vanruymbeke, M.

    Several methods investigated in order to calibrate gravimeters by the inertial acceleration produced by a vertical motion are described. The VRR 8601 calibrating platform is especially designed to calibrate La Coste and Romberg gravimeters. For heavier gravimeters such as tidal La Coste or superconducting instruments, two other principles are possible to lift up sinusoidally the platform: a mercury crapaudine or the rotation on an inclined plane.

  3. National Community Solar Platform

    Energy Technology Data Exchange (ETDEWEB)

    Rupert, Bart [Clean Energy Collective, Louisville, CO (United States)

    2016-06-30

    This project was created to provide a National Community Solar Platform (NCSP) portal known as Community Solar Hub, that is available to any entity or individual who wants to develop community solar. This has been done by providing a comprehensive portal to make CEC’s solutions, and other proven community solar solutions, externally available for everyone to access – making the process easy through proven platforms to protect subscribers, developers and utilities. The successful completion of this project provides these tools via a web platform and integration APIs, a wide spectrum of community solar projects included in the platform, multiple groups of customers (utilities, EPCs, and advocates) using the platform to develop community solar, and open access to anyone interested in community solar. CEC’s Incubator project includes web-based informational resources, integrated systems for project information and billing systems, and engagement with customers and users by community solar experts. The combined effort externalizes much of Clean Energy Collective’s industry-leading expertise, allowing third parties to develop community solar without duplicating expensive start-up efforts. The availability of this platform creates community solar projects that are cheaper to build and cheaper to participate in, furthering the goals of DOE’s SunShot Initiative. Final SF 425 Final SF 428 Final DOE F 2050.11 Final Report Narrative

  4. The Physics of Polarization

    Science.gov (United States)

    Landi Degl'Innocenti, Egidio

    2015-10-01

    The introductory lecture that has been delivered at this Symposium is a condensed version of an extended course held by the author at the XII Canary Island Winter School from November 13 to November 21, 2000. The full series of lectures can be found in Landi Degl'Innocenti (2002). The original reference is organized in 20 Sections that are here itemized: 1. Introduction, 2. Description of polarized radiation, 3. Polarization and optical devices: Jones calculus and Muller matrices, 4. The Fresnel equations, 5. Dichroism and anomalous dispersion, 6. Polarization in everyday life, 7. Polarization due to radiating charges, 8. The linear antenna, 9. Thomson scattering, 10. Rayleigh scattering, 11. A digression on Mie scattering, 12. Bremsstrahlung radiation, 13. Cyclotron radiation, 14. Synchrotron radiation, 15. Polarization in spectral lines, 16. Density matrix and atomic polarization, 17. Radiative transfer and statistical equilibrium equations, 18. The amplification condition in polarized radiative transfer, and 19. Coupling radiative transfer and statistical equilibrium equations.

  5. Cloud Based Earth Observation Data Exploitation Platforms

    Science.gov (United States)

    Romeo, A.; Pinto, S.; Loekken, S.; Marin, A.

    2017-12-01

    In the last few years data produced daily by several private and public Earth Observation (EO) satellites reached the order of tens of Terabytes, representing for scientists and commercial application developers both a big opportunity for their exploitation and a challenge for their management. New IT technologies, such as Big Data and cloud computing, enable the creation of web-accessible data exploitation platforms, which offer to scientists and application developers the means to access and use EO data in a quick and cost effective way. RHEA Group is particularly active in this sector, supporting the European Space Agency (ESA) in the Exploitation Platforms (EP) initiative, developing technology to build multi cloud platforms for the processing and analysis of Earth Observation data, and collaborating with larger European initiatives such as the European Plate Observing System (EPOS) and the European Open Science Cloud (EOSC). An EP is a virtual workspace, providing a user community with access to (i) large volume of data, (ii) algorithm development and integration environment, (iii) processing software and services (e.g. toolboxes, visualization routines), (iv) computing resources, (v) collaboration tools (e.g. forums, wiki, etc.). When an EP is dedicated to a specific Theme, it becomes a Thematic Exploitation Platform (TEP). Currently, ESA has seven TEPs in a pre-operational phase dedicated to geo-hazards monitoring and prevention, costal zones, forestry areas, hydrology, polar regions, urban areas and food security. On the technology development side, solutions like the multi cloud EO data processing platform provides the technology to integrate ICT resources and EO data from different vendors in a single platform. In particular it offers (i) Multi-cloud data discovery, (ii) Multi-cloud data management and access and (iii) Multi-cloud application deployment. This platform has been demonstrated with the EGI Federated Cloud, Innovation Platform Testbed Poland

  6. Developing a Communication link between Agents and cross Platform IDE

    OpenAIRE

    AAMIR, ZEESHAN

    2010-01-01

    The main objective of this thesis work is to develop communication link between Runrev Revolution (IDE) and JADE (Multi-Agent System) through Socket programming using TCP/IP layer. These two independent platforms are connected using socket programming technique. Socket programming is considered to be newly emerging technology among these two platforms, the work done in this thesis work is considered to be a prototype.A Graphical simulation model is developed by salixphere (Company in Hedemora...

  7. Physics with polarization at the SLD

    International Nuclear Information System (INIS)

    Burrows, P.N.

    1990-05-01

    The SLD detector is nearing completion and will start physics-quality data-taking at the SLC in 1991 with a longitudinally polarized electron beam and unpolarized positron beam. The current status of the detector is reviewed and the rich program of physics measurements possible with polarization and the SLD detector is briefly presented. In particular, the left-right polarization asymmetry, A LR , will be a unique measurement for the next few years and will allow tight bounds to be set upon the mass of the top quark. 14 refs., 1 fig

  8. Polarization calculations for electron storage rings

    International Nuclear Information System (INIS)

    Mane, S.R.

    1988-05-01

    A computer program called SMILE has been developed to calculate the equilibrium polarization in a high-energy electron storage ring. It can calculate spin resonances to arbitrary orders, in principle. Results of polarization calculations are shown for a variety of storage ring models, to elucidate various aspects of the behaviour of the polarization, such as the effects of machine symmetry, beam energy spread, and transverse momentum recoils, etc. Reasonable agreement is obtained with some experimental data from measurements at SPEAR. 12 refs., 12 figs

  9. Advantages of polarization experiments at RHIC

    International Nuclear Information System (INIS)

    Underwood, D.G.

    1990-01-01

    We point out various spin experiments that could be done if the polarized beam option is pursued at RHIC. The advantages of RHIC for investigating several current and future physics problems are discussed. In particular, the gluon spin dependent structure function of the nucleon could be measured cleanly and systematically. Relevant experience developed in conjunction with the Fermilab Polarized Beam program is also presented. 8 refs., 2 tabs

  10. Semantic-enabled Spatiotemporal Web Portal for Polar Sciences

    Science.gov (United States)

    Liu, K.

    2014-12-01

    It is essential for Intergovernmental and scientists to study, monitor and analyze the geographic data in polar regions. Polarregions are likely to respond rapidly and more severely to the climate changesthan any other area on the Earth.They also have significant importance for Global warming research. The ocean water around the Antarctic and Arctic is a crucial part of the ocean's thermohaline circulation. The Polar Cyberinfrastructure Program was built to acquire, share, access, analyze the polar data for Arctic and Antarctic communities. The polar data are becoming big and bring challenges for Polar Cyberinfrastructure Program including: 1) it is difficultfor polar data users to discover most relevant data based on the understanding the behavior; 2) the quality of polar data service is essential to use the polar data, however, it varies for users in different locations and different time. The semantic enabled discovery and volunteer computing are used in the Polar Cyberinfrastructurefor tackling these challenges: 1) semantic search and knowledge reasoning to improve the discovery recall and precision of polar data; 2) volunteer computing is used to gather volunteers computing resources around the world to improve the quality evaluationaccuracy of polar data service. Keywords: Polar Science, Cyberinfrastructure, Semantic, Volunteer Computing

  11. Developing the concept of a geostationary platform. [for communication services

    Science.gov (United States)

    Carey, W. T.; Bowman, R. M.; Stone, G. R.

    1980-01-01

    A geostationary platform concept with a proliferation of low-cost earth stations is discussed. Candidate platform concepts, servicing, life, and Orbital Transfer Vehicle (OTV) options are considered. A Life Cycle Costing model is used to select the minimum cost concept meeting program criteria. It is concluded that the geostationary platform concept is a practical and economical approach to providing expanding communication services within the limitations imposed by the available frequency spectrum and orbital arc.

  12. Transactional Network Platform: Applications

    Energy Technology Data Exchange (ETDEWEB)

    Katipamula, Srinivas; Lutes, Robert G.; Ngo, Hung; Underhill, Ronald M.

    2013-10-31

    In FY13, Pacific Northwest National Laboratory (PNNL) with funding from the Department of Energy’s (DOE’s) Building Technologies Office (BTO) designed, prototyped and tested a transactional network platform to support energy, operational and financial transactions between any networked entities (equipment, organizations, buildings, grid, etc.). Initially, in FY13, the concept demonstrated transactions between packaged rooftop air conditioners and heat pump units (RTUs) and the electric grid using applications or "agents" that reside on the platform, on the equipment, on a local building controller or in the Cloud. The transactional network project is a multi-lab effort with Oakridge National Laboratory (ORNL) and Lawrence Berkeley National Laboratory (LBNL) also contributing to the effort. PNNL coordinated the project and also was responsible for the development of the transactional network (TN) platform and three different applications associated with RTUs. This document describes two applications or "agents" in details, and also summarizes the platform. The TN platform details are described in another companion document.

  13. Alaskan Exemplary Program The Rural Alaska Honors Institute (RAHI) A Quarter Century of Success of Educating, Nurturing, and Retaining Alaska Native and Rural Students An International Polar Year Adventure in Barrow

    Science.gov (United States)

    Wartes, D.; Owens, G.

    2007-12-01

    UA system who participated in RAHI are nearly twice as likely to earn a bachelors degree, than those who did not attend RAHI. This summer, in celebration of the International Polar Year, in collaboration with Ilisagvik College, at the completion of the traditional RAHI program, ten RAHI students flew to Barrow for an additional two weeks of study. Five students participated in an archaeological dig and five students performed research with the Barrow Arctic Science Consortium scientists studying climate change. In addition, ten students from Greenland visited the program, with plans to more fully participate next summer. This added dimension to the program has proved successful, allowing the students to compare and contrast between their own countries and indigenous perspectives. Global warming was an issue that was hotly debated, as its effects are so evident in the Polar Regions. In the Arctic, life is directly tied to the ice and snow. As the ice disappears and/or changes, the Indigenous people have to adapt. RAHI would like to share with you some of the results of this past summers IPY activities.

  14. Polar Seismic TETwalker: Integrating Engineering Teaching and Research

    Science.gov (United States)

    Gifford, C. M.; Ruiz, I.; Carmichael, B. L.; Wade, U. B.; Agah, A.

    2007-12-01

    Based on the TETwalker robot platform at NASA/Goddard Space Flight Center, the Center for Remote Sensing of Ice Sheets (CReSIS) has begun work on designing and modeling the integration of seismic surveying equipment into the TETwalker robot architecture for use in polar environments. Employing multiple Seismic TETwalker robots will allow gathering of polar seismic data in previously inaccessible or unexplored terrains, as well as help significantly reduce human involvement in such harsh environments. NASA's TETwalker mobile robot uses a unique form of mobility to topple across the surface and over obstacles. This robot therefore does not suffer the fate of other wheeled and tracked robots if tipped over. It is composed of extending struts and nodes, forming a tetrahedral shape which can be strategically adjusted to change the robot's center of gravity for toppling. Of the many platforms the TETwalker architecture can form, the 4-TETwalker robot (consisting of four ground nodes, a center payload node, and interconnecting struts) has been the focus of current research. The center node has been chosen as the geophone deployment medium, designed in such a way to allow geophone insertion using any face of the robot's structure. As the robot comes to rest at the deployment location, one of its faces will rest on the surface. No matter which side it is resting on, a geophone spike will be perpendicular to its face and an extending strut will be vertical for pushing the geophone into the ground. Lengthening and shortening struts allow the deployment node to precisely place the geophone into the ground, as well as vertically orient the geophones for proper data acquisition on non-flat surfaces. Power source integration has been investigated, incorporating possible combinations of solar, wind, and vibration power devices onboard the robot models for long-term survival in a polar environment. Designs have also been modeled for an alternate center node sensor package (e

  15. [Review] Polarization and Polarimetry

    Science.gov (United States)

    Trippe, Sascha

    2014-02-01

    Polarization is a basic property of light and is fundamentally linked to the internal geometry of a source of radiation. Polarimetry complements photometric, spectroscopic, and imaging analyses of sources of radiation and has made possible multiple astrophysical discoveries. In this article I review (i) the physical basics of polarization: electromagnetic waves, photons, and parameterizations; (ii) astrophysical sources of polarization: scattering, synchrotron radiation, active media, and the Zeeman, Goldreich-Kylafis, and Hanle effects, as well as interactions between polarization and matter (like birefringence, Faraday rotation, or the Chandrasekhar-Fermi effect); (iii) observational methodology: on-sky geometry, influence of atmosphere and instrumental polarization, polarization statistics, and observational techniques for radio, optical, and X/γ wavelengths; and (iv) science cases for astronomical polarimetry: solar and stellar physics, planetary system bodies, interstellar matter, astrobiology, astronomical masers, pulsars, galactic magnetic fields, gamma-ray bursts, active galactic nuclei, and cosmic microwave background radiation.

  16. Identification of platform levels

    DEFF Research Database (Denmark)

    Mortensen, Niels Henrik

    2005-01-01

    These years many companies are changing their product development from single to multi product development, meaning that not only one product is developed but product families. There are many reasons for this change, but among the most important ones are reduction of time to market, total cost...... product development in one step and therefore the objective of this paper is to identify levels of platform based product development. The structure of this paper is as follows. First the applied terminology for platforms will be briefly explained and then characteristics between single and multi product...... development will be examined. Based on the identification of the above characteristics five platform levels are described. The research presented in this paper is a result of MSc, Ph.D projects at the Technical University of Denmark and consultancy projects within the organisation of Institute of Product...

  17. Reusable platform concepts

    International Nuclear Information System (INIS)

    Gudmestad, O.T.; Sparby, B.K.; Stead, B.L.

    1993-01-01

    There is an increasing need to reduce costs of offshore production facilities in order to make development of offshore fields profitable. For small fields with short production time there is in particular a need to investigate ways to reduce costs. The idea of platform reuse is for such fields particularly attractive. This paper will review reusable platform concepts and will discuss their range of application. Particular emphasis will be placed on technical limitations. Traditional concepts as jackups and floating production facilities will be discussed by major attention will be given to newly developed ideas for reuse of steel jackets and concrete structures. It will be shown how the operator for several fields can obtain considerable savings by applying such reusable platform concepts

  18. Polarization feedback laser stabilization

    Science.gov (United States)

    Esherick, P.; Owyoung, A.

    1987-09-28

    A system for locking two Nd:YAG laser oscillators includes an optical path for feeding the output of one laser into the other with different polarizations. Elliptical polarization is incorporated into the optical path so that the change in polarization that occurs when the frequencies coincide may be detected to provide a feedback signal to control one laser relative to the other. 4 figs.

  19. Polarization in Sagittarius A*

    OpenAIRE

    Bower, Geoffrey C.

    2000-01-01

    We summarize the current state of polarization observations of Sagittarius A*, the compact radio source and supermassive black hole candidate in the Galactic Center. These observations are providing new tools for understanding accretion disks, jets and their environments. Linear polarization observations have shown that Sgr A* is unpolarized at frequencies as high as 86 GHz. However, recent single-dish observations indicate that Sgr A* may have strong linear polarization at frequencies higher...

  20. Cross platform SCA component using C++ builder and KYLIX

    International Nuclear Information System (INIS)

    Nishimura, Hiroshi; Timossi, Chiris; McDonald, James L.

    2003-01-01

    A cross-platform component for EPICS Simple Channel Access (SCA) has been developed. EPICS client programs with GUI become portable at their C++ source-code level both on Windows and Linux by using Borland C++ Builder 6 and Kylix 3 on these platforms respectively

  1. The ILC polarized electron source

    CERN Document Server

    Brachmann, Axel; Garwin, Edward; Kirby, Robert; Luh Dah An; Maruyama, Takashi; Prepost, Richard; Schultz, David; Sheppard, John

    2005-01-01

    The SLC polarized electron source (PES) can meet the expected requirements of the International Linear Collider (ILC) for polarization, charge and lifetime. However, experience with newer and successful PES designs at JLAB, Mainz and elsewhere can be incorporated into a first-generation ILC source that will emphasize reliability and stability without compromising the photocathode performance. The long pulse train for the ILC may introduce new challenges for the PES, and in addition more reliable and stable operation of the PES may be achievable if appropriate R&D is carried out for higher voltage operation and for a simpler load-lock system. The outline of the R&D program currently taking shape at SLAC and elsewhere is discussed. The principal components of the proposed ILC PES, including the laser system necessary for operational tests, are described.

  2. Windows Azure Platform

    CERN Document Server

    Redkar, Tejaswi

    2010-01-01

    The Azure Services Platform is a brand-new cloud-computing technology from Microsoft. It is composed of four core components-Windows Azure, .NET Services, SQL Services, and Live Services-each with a unique role in the functioning of your cloud service. It is the goal of this book to show you how to use these components, both separately and together, to build flawless cloud services. At its heart Windows Azure Platform is a down-to-earth, code-centric book. This book aims to show you precisely how the components are employed and to demonstrate the techniques and best practices you need to know

  3. Windows Azure Platform

    CERN Document Server

    Redkar, Tejaswi

    2011-01-01

    The Windows Azure Platform has rapidly established itself as one of the most sophisticated cloud computing platforms available. With Microsoft working to continually update their product and keep it at the cutting edge, the future looks bright - if you have the skills to harness it. In particular, new features such as remote desktop access, dynamic content caching and secure content delivery using SSL make the latest version of Azure a more powerful solution than ever before. It's widely agreed that cloud computing has produced a paradigm shift in traditional architectural concepts by providin

  4. Airborne Laser Polarization Sensor

    Science.gov (United States)

    Kalshoven, James, Jr.; Dabney, Philip

    1991-01-01

    Instrument measures polarization characteristics of Earth at three wavelengths. Airborne Laser Polarization Sensor (ALPS) measures optical polarization characteristics of land surface. Designed to be flown at altitudes of approximately 300 m to minimize any polarizing or depolarizing effects of intervening atmosphere and to look along nadir to minimize any effects depending on look angle. Data from measurements used in conjunction with data from ground surveys and aircraft-mounted video recorders to refine mathematical models used in interpretation of higher-altitude polarimetric measurements of reflected sunlight.

  5. Polarization at SLC

    International Nuclear Information System (INIS)

    Swartz, M.L.

    1988-07-01

    The SLAC Linear Collider has been designed to readily accommodate polarized electron beams. Considerable effort has been made to implement a polarized source, a spin rotation system, and a system to monitor the beam polarization. Nearly all major components have been fabricated. At the current time, several source and polarimeter components have been installed. The installation and commissioning of the entire system will take place during available machine shutdown periods as the commissioning of SLC progresses. It is expected that a beam polarization of 45% will be achieved with no loss in luminosity. 13 refs., 15 figs

  6. Chicxulub Impact, Yucatan Carbonate Platform, Cretaceous-Paleogene Boundary and Paleocene-Eocene Thermal Maximum

    Science.gov (United States)

    Fucugauchi, J. U.; Perez-Cruz, L. L.

    2015-12-01

    Chicxulub formed 66 Ma ago by an asteroid impact on the Yucatan carbonate platform, southern Gulf of Mexico. Impact produced a 200 km diameter crater, platform fracturing, deformation and ejecta emplacement. Carbonate sedimentation restarted and crater was covered by up to 1 km of sediments. Drilling programs have sampled the Paleogene sediments, which record the changing sedimentation processes in the impact basin and platform. Here, results of a study of the Paleocene-Eocene sediments cored in the Santa Elena borehole are used to characterize the K/Pg and PETM. The borehole reached a depth of 504 m and was continuously cored, sampling the post-impact sediments and impact breccias, with contact at 332 m. For this study, we analyzed the section from ~230 to ~340 m, corresponding to the upper breccias and Paleocene-Eocene sediments. The lithological column, constructed from macroscopic and thin-section petrographic analyses, is composed of limestones and dolomitized limestones with several thin clay layers. Breccias are melt and basement clast rich, described as a suevitic unit. Section is further investigated using paleomagnetic, rock magnetic, X-ray fluorescence geochemical and stable isotope analyses. Magnetic polarities define a sequence of reverse to normal, which correlate to the geomagnetic polarity time scale from chrons 29r to 26r. The d13 C values in the first 20 m interval range from 1.2 to 3.5 %0 and d18 O values range from -1.4 to -4.8 %0. Isotope values show variation trends that correlate with the marine carbon and oxygen isotope patterns for the K-Pg boundary and early Paleocene. Positive carbon isotopes suggest relatively high productivity, with apparent recovery following the K-Pg extinction event. Geochemical data define characteristic trends, with Si decreasing gradually from high values in the suevites, low contents in Paleocene sediments with intervals of higher variability and then increased values likely marking the PETM. Variation trends are

  7. An integrated platform for biomolecule interaction analysis

    Science.gov (United States)

    Jan, Chia-Ming; Tsai, Pei-I.; Chou, Shin-Ting; Lee, Shu-Sheng; Lee, Chih-Kung

    2013-02-01

    We developed a new metrology platform which can detect real-time changes in both a phase-interrogation mode and intensity mode of a SPR (surface plasmon resonance). We integrated a SPR and ellipsometer to a biosensor chip platform to create a new biomolecular interaction measurement mechanism. We adopted a conductive ITO (indium-tinoxide) film to the bio-sensor platform chip to expand the dynamic range and improve measurement accuracy. The thickness of the conductive film and the suitable voltage constants were found to enhance performance. A circularly polarized ellipsometry configuration was incorporated into the newly developed platform to measure the label-free interactions of recombinant human C-reactive protein (CRP) with immobilized biomolecule target monoclonal human CRP antibody at various concentrations. CRP was chosen as it is a cardiovascular risk biomarker and is an acute phase reactant as well as a specific prognostic indicator for inflammation. We found that the sensitivity of a phaseinterrogation SPR is predominantly dependent on the optimization of the sample incidence angle. The effect of the ITO layer effective index under DC and AC effects as well as an optimal modulation were experimentally performed and discussed. Our experimental results showed that the modulated dynamic range for phase detection was 10E-2 RIU based on a current effect and 10E-4 RIU based on a potential effect of which a 0.55 (°/RIU) measurement was found by angular-interrogation. The performance of our newly developed metrology platform was characterized to have a higher sensitivity and less dynamic range when compared to a traditional full-field measurement system.

  8. Games and Platform Decisions

    DEFF Research Database (Denmark)

    Hansen, Poul H. Kyvsgård; Mikkola, Juliana Hsuan

    2007-01-01

    is the application of on-line games in order to provide training for decision makers and in order to generate overview over the implications of platform decisions. However, games have to be placed in a context with other methods and we argue that a mixture of games, workshops, and simulations can provide improved...

  9. CERN Neutrino Platform Hardware

    CERN Document Server

    Nelson, Kevin

    2017-01-01

    My summer research was broadly in CERN's neutrino platform hardware efforts. This project had two main components: detector assembly and data analysis work for ICARUS. Specifically, I worked on assembly for the ProtoDUNE project and monitored the safety of ICARUS as it was transported to Fermilab by analyzing the accelerometer data from its move.

  10. Creative Platform Learning (CPL)

    DEFF Research Database (Denmark)

    Christensen, Jonna Langeland; Hansen, Søren

    Creative Platform Learning (CPL) er en pædagogisk metode, der skaber foretagsomme og innovative elever, der kan anvende deres kreativitet til at lære nyt. Ifølge den nye skolereform skal Innovation og entreprenørskab tydeliggøres i alle fag. I CPL er det en integreret del af undervisningen...

  11. Postgraduate programmes as platform

    NARCIS (Netherlands)

    drs Ben Smit; Dr. Jacqueline van Swet; Prof.Dr. Petra Ponte

    2007-01-01

    Typical of postgraduate courses for experienced teachers is the wealth of professional experience that the studetns bring with them. Such students can examine their own practice, for which they are fully responsible. Authors from diverse backgrounds address important aspects of the platform, such as

  12. RHIC Polarized proton operation

    International Nuclear Information System (INIS)

    Huang, H.; Ahrens, L.; Alekseev, I.G.; Aschenauer, E.; Atoian, G.; Bai, M.; Bazilevsky, A.; Blaskiewicz, M.; Brennan, J.M.; Brown, K.A.; Bruno, D.; Connolly, R.; Dion, A.; D'Ottavio, T.; Drees, K.A.; Fischer, W.; Gardner, C.; Glenn, J.W.; Gu, X.; Harvey, M.; Hayes, T.; Hoff, L.; Hulsart, R.L.; Laster, J.; Liu, C.; Luo, Y.; MacKay, W.W.; Makdisi, Y.; Marr, G.J.; Marusic, A.; Meot, F.; Mernick, K.; Michnoff, R.; Minty, M.; Montag, C.; Morris, J.; Nemesure, S.; Poblaguev, A.; Ptitsyn, V.; Ranjibar, V.; Robert-Demolaize, G.; Roser, T.; Schmidke, B.; Schoefer, V.; Severino, F.; Smirnov, D.; Smith, K.; Steski, D.; Svirida, D.; Tepikian, S.; Trbojevic, D.; Tsoupas, N.; Tuozzolo, J.E.; Wang, G.; Wilinski, M.; Yip, K.; Zaltsman, A.; Zelenski, A.; Zeno, K.; Zhang, S.Y.

    2011-01-01

    The Relativistic Heavy Ion Collider (RHIC) operation as the polarized proton collider presents unique challenges since both luminosity(L) and spin polarization(P) are important. With longitudinally polarized beams at the experiments, the figure of merit is LP 4 . A lot of upgrades and modifications have been made since last polarized proton operation. A 9 MHz rf system is installed to improve longitudinal match at injection and to increase luminosity. The beam dump was upgraded to increase bunch intensity. A vertical survey of RHIC was performed before the run to get better magnet alignment. The orbit control is also improved this year. Additional efforts are put in to improve source polarization and AGS polarization transfer efficiency. To preserve polarization on the ramp, a new working point is chosen such that the vertical tune is near a third order resonance. The overview of the changes and the operation results are presented in this paper. Siberian snakes are essential tools to preserve polarization when accelerating polarized beams to higher energy. At the same time, the higher order resonances still can cause polarization loss. As seen in RHIC, the betatron tune has to be carefully set and maintained on the ramp and during the store to avoid polarization loss. In addition, the orbit control is also critical to preserve polarization. The higher polarization during this run comes from several improvements over last run. First we have a much better orbit on the ramp. The orbit feedback brings down the vertical rms orbit error to 0.1mm, much better than the 0.5mm last run. With correct BPM offset and vertical realignment, this rms orbit error is indeed small. Second, the jump quads in the AGS improved input polarization for RHIC. Third, the vertical tune was pushed further away from 7/10 snake resonance. The tune feedback maintained the tune at the desired value through the ramp. To calibrate the analyzing power of RHIC polarimeters at any energy above

  13. RHIC Polarized proton operation

    Energy Technology Data Exchange (ETDEWEB)

    Huang, H.; Ahrens, L.; Alekseev, I.G.; Aschenauer, E.; Atoian, G.; Bai, M.; Bazilevsky, A.; Blaskiewicz, M.; Brennan, J.M.; Brown, K.A.; Bruno, D.; Connolly, R.; Dion, A.; D' Ottavio, T.; Drees, K.A.; Fischer, W.; Gardner, C.; Glenn, J.W.; Gu, X.; Harvey, M.; Hayes, T.; Hoff, L.; Hulsart, R.L.; Laster, J.; Liu, C.; Luo, Y.; MacKay, W.W.; Makdisi, Y.; Marr, G.J.; Marusic, A.; Meot, F.; Mernick, K.; Michnoff, R,; Minty, M.; Montag, C.; Morris, J.; Nemesure, S.; Poblaguev, A.; Ptitsyn, V.; Ranjibar, V.; Robert-Demolaize, G.; Roser, T.; J.; Severino, F.; Schmidke, B.; Schoefer, V.; Severino, F.; Smirnov, D.; Smith, K.; Steski, D.; Svirida, D.; Tepikian, S.; Trbojevic, D.; Tsoupas, N.; Tuozzolo, J. Wang, G.; Wilinski, M.; Yip, K.; Zaltsman, A.; Zelenski, A.; Zeno, K.; Zhang, S.Y.

    2011-03-28

    The Relativistic Heavy Ion Collider (RHIC) operation as the polarized proton collider presents unique challenges since both luminosity(L) and spin polarization(P) are important. With longitudinally polarized beams at the experiments, the figure of merit is LP{sup 4}. A lot of upgrades and modifications have been made since last polarized proton operation. A 9 MHz rf system is installed to improve longitudinal match at injection and to increase luminosity. The beam dump was upgraded to increase bunch intensity. A vertical survey of RHIC was performed before the run to get better magnet alignment. The orbit control is also improved this year. Additional efforts are put in to improve source polarization and AGS polarization transfer efficiency. To preserve polarization on the ramp, a new working point is chosen such that the vertical tune is near a third order resonance. The overview of the changes and the operation results are presented in this paper. Siberian snakes are essential tools to preserve polarization when accelerating polarized beams to higher energy. At the same time, the higher order resonances still can cause polarization loss. As seen in RHIC, the betatron tune has to be carefully set and maintained on the ramp and during the store to avoid polarization loss. In addition, the orbit control is also critical to preserve polarization. The higher polarization during this run comes from several improvements over last run. First we have a much better orbit on the ramp. The orbit feedback brings down the vertical rms orbit error to 0.1mm, much better than the 0.5mm last run. With correct BPM offset and vertical realignment, this rms orbit error is indeed small. Second, the jump quads in the AGS improved input polarization for RHIC. Third, the vertical tune was pushed further away from 7/10 snake resonance. The tune feedback maintained the tune at the desired value through the ramp. To calibrate the analyzing power of RHIC polarimeters at any energy above

  14. Evaluation of Extraction Protocols for Simultaneous Polar and Non-Polar Yeast Metabolite Analysis Using Multivariate Projection Methods

    Directory of Open Access Journals (Sweden)

    Nicolas P. Tambellini

    2013-07-01

    Full Text Available Metabolomic and lipidomic approaches aim to measure metabolites or lipids in the cell. Metabolite extraction is a key step in obtaining useful and reliable data for successful metabolite studies. Significant efforts have been made to identify the optimal extraction protocol for various platforms and biological systems, for both polar and non-polar metabolites. Here we report an approach utilizing chemoinformatics for systematic comparison of protocols to extract both from a single sample of the model yeast organism Saccharomyces cerevisiae. Three chloroform/methanol/water partitioning based extraction protocols found in literature were evaluated for their effectiveness at reproducibly extracting both polar and non-polar metabolites. Fatty acid methyl esters and methoxyamine/trimethylsilyl derivatized aqueous compounds were analyzed by gas chromatography mass spectrometry to evaluate non-polar or polar metabolite analysis. The comparative breadth and amount of recovered metabolites was evaluated using multivariate projection methods. This approach identified an optimal protocol consisting of 64 identified polar metabolites from 105 ion hits and 12 fatty acids recovered, and will potentially attenuate the error and variation associated with combining metabolite profiles from different samples for untargeted analysis with both polar and non-polar analytes. It also confirmed the value of using multivariate projection methods to compare established extraction protocols.

  15. Single Electron Transistor Platform for Microgravity Proteomics, Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — This Phase II program builds from the successful Phase I efforts to demonstrate that Quantum Logic Devices' nanoelectronic platform for biological detection could...

  16. Our Polar Past

    Science.gov (United States)

    Clary, Renee; Wandersee, James

    2009-01-01

    The study of polar exploration is fascinating and offers students insights into the history, culture, and politics that affect the developing sciences at the farthest ends of Earth. Therefore, the authors think there is value in incorporating polar exploration accounts within modern science classrooms, and so they conducted research to test their…

  17. Terahertz polarization imaging

    NARCIS (Netherlands)

    Van der Valk, N.C.J.; Van der Marel, W.A.M.; Planken, P.C.M.

    2005-01-01

    We present a new method to measure the polarization state of a terahertz pulse by using a modified electrooptic sampling setup. To illustrate the power of this method, we show two examples in which the knowledge of the polarization of the terahertz pulse is essential for interpreting the results:

  18. Polarized proton beams

    International Nuclear Information System (INIS)

    Roser, T.

    1995-01-01

    The acceleration of polarized proton beams in circular accelerators is complicated by the presence of numerous depolarizing spin resonances. Careful and tedious minimization of polarization loss at each of these resonances allowed acceleration of polarized proton beams up to 22 GeV. It has been the hope that Siberian Snakes, which are local spin rotators inserted into ring accelerators, would eliminate these resonances and allow acceleration of polarized beams with the same ease and efficiency that is now routine for unpolarized beams. First tests at IUCF with a full Siberian Snake showed that the spin dynamics with a Snake can be understood in detail. The author now has results of the first tests of a partial Siberian Snake at the AGS, accelerating polarized protons to an energy of about 25 GeV. These successful tests of storage and acceleration of polarized proton beams open up new possibilities such as stored polarized beams for internal target experiments and high energy polarized proton colliders

  19. Polar Science Is Cool!

    Science.gov (United States)

    Weeks, Sophie

    2012-01-01

    Children are fascinated by the fact that polar scientists do research in extremely cold and dangerous places. In the Arctic they might be viewed as lunch by a polar bear. In the Antarctic, they could lose toes and fingers to frostbite and the wind is so fast it can rip skin off. They camp on ice in continuous daylight, weeks from any form of…

  20. Precision Polarization of Neutrons

    Science.gov (United States)

    Martin, Elise; Barron-Palos, Libertad; Couture, Aaron; Crawford, Christopher; Chupp, Tim; Danagoulian, Areg; Estes, Mary; Hona, Binita; Jones, Gordon; Klein, Andi; Penttila, Seppo; Sharma, Monisha; Wilburn, Scott

    2009-05-01

    Determining polarization of a cold neutron beam to high precision is required for the next generation neutron decay correlation experiments at the SNS, such as the proposed abBA and PANDA experiments. Precision polarimetry measurements were conducted at Los Alamos National Laboratory with the goal of determining the beam polarization to the level of 10-3 or better. The cold neutrons from FP12 were polarized using optically polarized ^3He gas as a spin filter, which has a highly spin-dependent absorption cross section. A second ^ 3He spin filter was used to analyze the neutron polarization after passing through a resonant RF spin rotator. A discussion of the experiment and results will be given.

  1. Optically polarized 3He

    Science.gov (United States)

    Gentile, T. R.; Nacher, P. J.; Saam, B.; Walker, T. G.

    2018-01-01

    This article reviews the physics and technology of producing large quantities of highly spin-polarized 3He nuclei using spin-exchange (SEOP) and metastability-exchange (MEOP) optical pumping. Both technical developments and deeper understanding of the physical processes involved have led to substantial improvements in the capabilities of both methods. For SEOP, the use of spectrally narrowed lasers and K-Rb mixtures has substantially increased the achievable polarization and polarizing rate. For MEOP nearly lossless compression allows for rapid production of polarized 3He and operation in high magnetic fields has likewise significantly increased the pressure at which this method can be performed, and revealed new phenomena. Both methods have benefitted from development of storage methods that allow for spin-relaxation times of hundreds of hours, and specialized precision methods for polarimetry. SEOP and MEOP are now widely applied for spin-polarized targets, neutron spin filters, magnetic resonance imaging, and precision measurements. PMID:29503479

  2. Optically polarized 3He

    Science.gov (United States)

    Gentile, T. R.; Nacher, P. J.; Saam, B.; Walker, T. G.

    2017-10-01

    This article reviews the physics and technology of producing large quantities of highly spin-polarized 3He nuclei using spin-exchange (SEOP) and metastability-exchange (MEOP) optical pumping. Both technical developments and deeper understanding of the physical processes involved have led to substantial improvements in the capabilities of both methods. For SEOP, the use of spectrally narrowed lasers and K-Rb mixtures has substantially increased the achievable polarization and polarizing rate. For MEOP nearly lossless compression allows for rapid production of polarized 3He and operation in high magnetic fields has likewise significantly increased the pressure at which this method can be performed, and revealed new phenomena. Both methods have benefitted from development of storage methods that allow for spin-relaxation times of hundreds of hours, and specialized precision methods for polarimetry. SEOP and MEOP are now widely applied for spin-polarized targets, neutron spin filters, magnetic resonance imaging, and precision measurements.

  3. Parallel Polarization State Generation.

    Science.gov (United States)

    She, Alan; Capasso, Federico

    2016-05-17

    The control of polarization, an essential property of light, is of wide scientific and technological interest. The general problem of generating arbitrary time-varying states of polarization (SOP) has always been mathematically formulated by a series of linear transformations, i.e. a product of matrices, imposing a serial architecture. Here we show a parallel architecture described by a sum of matrices. The theory is experimentally demonstrated by modulating spatially-separated polarization components of a laser using a digital micromirror device that are subsequently beam combined. This method greatly expands the parameter space for engineering devices that control polarization. Consequently, performance characteristics, such as speed, stability, and spectral range, are entirely dictated by the technologies of optical intensity modulation, including absorption, reflection, emission, and scattering. This opens up important prospects for polarization state generation (PSG) with unique performance characteristics with applications in spectroscopic ellipsometry, spectropolarimetry, communications, imaging, and security.

  4. Perspectives of the digital mammography platform

    International Nuclear Information System (INIS)

    Gruber, R.; Riedl, C.C.; Reisegger, M.; Pinker, K.; Sturm, E.; Semturs, F.; Helbich, T.H.

    2010-01-01

    In Europe one out of every nine women suffers from breast cancer during her lifetime. Since the introduction of mammography screening programs more breast cancers are being diagnosed when they are still small and early stage cancers with a favourable prognosis. The introduction of digital mammography systems has led to a continuous reduction of breast cancer mortality especially in specific patient subgroups. Furthermore, the digital mammography platform enables the development of new, innovative breast imaging methods to increase sensitivity and decrease breast cancer mortality. This digital mammography platform includes digital breast tomosynthesis, digital contrast medium mammography and digital contrast medium breast tomosynthesis as well as fused data sets from digital mammography with ultrasound or MRI. The following article summarizes these new applications, describes the strengths of the digital platform and illustrates the potential advantages of an improved breast cancer diagnosis by digital mammography. (orig.) [de

  5. Mobile Platforms and Development Environments

    CERN Document Server

    Helal, Sumi; Li, Wengdong

    2012-01-01

    Mobile platform development has lately become a technological war zone with extremely dynamic and fluid movement, especially in the smart phone and tablet market space. This Synthesis lecture is a guide to the latest developments of the key mobile platforms that are shaping the mobile platform industry. The book covers the three currently dominant native platforms -- iOS, Android and Windows Phone -- along with the device-agnostic HTML5 mobile web platform. The lecture also covers location-based services (LBS) which can be considered as a platform in its own right. The lecture utilizes a sampl

  6. Hybrid Photonic Integration on a Polymer Platform

    Directory of Open Access Journals (Sweden)

    Ziyang Zhang

    2015-09-01

    Full Text Available To fulfill the functionality demands from the fast developing optical networks, a hybrid integration approach allows for combining the advantages of various material platforms. We have established a polymer-based hybrid integration platform (polyboard, which provides flexible optical input/ouptut interfaces (I/Os that allow robust coupling of indium phosphide (InP-based active components, passive insertion of thin-film-based optical elements, and on-chip attachment of optical fibers. This work reviews the recent progress of our polyboard platform. On the fundamental level, multi-core waveguides and polymer/silicon nitride heterogeneous waveguides have been fabricated, broadening device design possibilities and enabling 3D photonic integration. Furthermore, 40-channel optical line terminals and compact, bi-directional optical network units have been developed as highly functional, low-cost devices for the wavelength division multiplexed passive optical network. On a larger scale, thermo-optic elements, thin-film elements and an InP gain chip have been integrated on the polyboard to realize a colorless, dual-polarization optical 90° hybrid as the frontend of a coherent receiver. For high-end applications, a wavelength tunable 100Gbaud transmitter module has been demonstrated, manifesting the joint contribution from the polyboard technology, high speed polymer electro-optic modulator, InP driver electronics and ceramic electronic interconnects.

  7. Platform Performance and Challenges - using Platforms in Lego Company

    DEFF Research Database (Denmark)

    Munk, Lone; Mortensen, Niels Henrik

    2009-01-01

    This article studies the performance and challenges of using nine implemented product platforms in LEGO Company. Most of these do produce results, but do not meet their goals due to challenges in their usage in the daily product. The main challenges are that the platforms are not being used...... by the product defining users (product developers) and platform erosion. When the platforms are not used it is due to: unsuitable calculation models, lack of goals, rewards or benefits from management, unattractive tradeoffs and difficulties in understanding the platform. This indicates that platform design...... needs focus on the incentive of using the platform. This problem lacks attention in literature, as well as industry, where assessment criteria do not cover this aspect. Therefore, we recommend including user incentive in platform assessment criteria to these challenges. Concrete solution elements...

  8. The ESA Geohazard Exploitation Platform

    Science.gov (United States)

    Bally, Philippe; Laur, Henri; Mathieu, Pierre-Philippe; Pinto, Salvatore

    2015-04-01

    Earthquakes represent one of the world's most significant hazards in terms both of loss of life and damages. In the first decade of the 21st century, earthquakes accounted for 60 percent of fatalities from natural disasters, according to the United Nations International Strategy for Disaster Reduction (UNISDR). To support mitigation activities designed to assess and reduce risks and improve response in emergency situations, satellite EO can be used to provide a broad range of geo-information services. This includes for instance crustal block boundary mapping to better characterize active faults, strain rate mapping to assess how rapidly faults are deforming, soil vulnerability mapping to help estimate how the soil is behaving in reaction to seismic phenomena, geo-information to assess the extent and intensity of the earthquake impact on man-made structures and formulate assumptions on the evolution of the seismic sequence, i.e. where local aftershocks or future main shocks (on nearby faults) are most likely to occur. In May 2012, the European Space Agency and the GEO Secretariat convened the International Forum on Satellite EO for Geohazards now known as the Santorini Conference. The event was the continuation of a series of international workshops such as those organized by the Geohazards Theme of the Integrated Global Observing Strategy Partnership. In Santorini the seismic community has set out a vision of the EO contribution to an operational global seismic risk program, which lead to the Geohazard Supersites and Natural Laboratories (GSNL) initiative. The initial contribution of ESA to suuport the GSNL was the first Supersites Exploitation Platform (SSEP) system in the framework of Grid Processing On Demand (GPOD), now followed by the Geohazard Exploitation Platform (GEP). In this presentation, we will describe the contribution of the GEP for exploiting satellite EO for geohazard risk assessment. It is supporting the GEO Supersites and has been further

  9. Available: motorised platform

    CERN Multimedia

    The COMPASS collaboration

    2014-01-01

    The COMPASS collaboration would like to offer to a new owner the following useful and fully operational piece of equipment, which is due to be replaced with better adapted equipment.   Please contact Erwin Bielert (erwin.bielert@cern.ch or 160539) for further information.  Motorized platform (FOR FREE):   Fabricated by ACL (Alfredo Cardoso & Cia Ltd) in Portugal. The model number is MeXs 5-­‐30.  Specifications: 5 m wide, 1 m deep, adjustable height (1.5 m if folded). Maximum working floor height: 4 m. conforms to CERN regulations, number LV158. Type LD500, capacity 500 kg and weight 2000 kg.  If no interested party is found before December 2014, the platform will be thrown away.

  10. Online stock trading platform

    Directory of Open Access Journals (Sweden)

    Ion LUNGU

    2006-01-01

    Full Text Available The Internet is the perfect tool that can assure the market’s transparency for any user who wants to trade on the stock market. The investor can have access to the market news, financial calendar or the press releases of the issuers. A good online trading platform also provides real-time intraday quotes, trading history and technical analysis giving the investor a clearer view of the supply and demand in the market. All this information provides the investor a good image of the market and encourages him to trade. This paper wishes to draft the pieces of an online trading platform and to analyze the impact of developing and implementing one in a brokerage firm.

  11. Polarization at the SLC

    Energy Technology Data Exchange (ETDEWEB)

    Moffeit, K.C.

    1988-10-01

    The Stanford Linear collider was designed to accommodate polarized electron beams. Longitudinally polarized electrons colliding with unpolarized positrons at a center of mass energy near the Z/sup 0/ mass can be used as novel and sensitive probes of the electroweak process. A gallium arsenide based photon emission source will provide a beam of longitudinally polarized electrons of about 45 percent polarization. A system of bend magnets and a superconducting solenoid will be used to rotate the spins so that the polarization is preserved while the 1.21 GeV electrons are stored in the damping ring. Another set of bend magnets and two superconducting solenoids orient the spin vectors so that longitudinal polarization of the electrons is achieved at the collision point with the unpolarized positrons. A system to monitor the polarization based on Moller and Compton scattering will be used. Nearly all major components have been fabricated and tested. Subsystems of the source and polarimeters have been installed, and studies are in progress. The installation and commissioning of the entire system will take place during available machine shutdown periods as the commissioning of SLC progresses. 8 refs., 16 figs., 1 tab.

  12. Optimizing a living kidney donation program: transition to hand-assisted retroperitoneoscopic living donor nephrectomy and introduction of a passive polarizing three-dimensional display system.

    Science.gov (United States)

    Wahba, Roger; Kleinert, Robert; Hellmich, Martin; Heiermann, Nadine; Dieplinger, Georg; Schlößer, Hans A; Buchner, Denise; Kurschat, Christine; Stippel, Dirk L

    2017-06-01

    Optimizing a living kidney donation program is important to guarantee a high grade of acceptance among potential donors. Hand-assisted retroperitoneoscopic donor nephrectomy (HARP) is an alternative to the open anterior approach (AA) technique. Problems associated to the learning curve could hinder a transition. 3D display technique seems to ease minimally invasive surgery. Aim of this study was to evaluate the learning curve during the transition from AA to HARP and the influence of the 3D display system on the established technique. Observational study (n = 207) during transition to HARP and introduction of 3D display technique. Operation time (OT), warm ischemia time (WIT) and blood loss (BL) of HARP decreased during transition. Pairwise group comparison for OT showed a significant learning effect for the first 30 out of 50 HARPs without influence on graft function. Between AA and HARP no significant difference in OT (133 ± 24 vs. 127 ± 19 min, p = 0.25) but for WIT (23 ± 28 vs. 126 ± 40 s, p transition to HARP is possible without additional risk for the donor or loss of quality for the recipient. The learning curve for HARP is steep and short. The introduction of 3D display technique after transition facilitates the surgical preparation and could further help to optimize HARP.

  13. In-situ electron and ion measurements and observed gravity wave effects in the polar mesosphere during the MaCWAVE program

    Directory of Open Access Journals (Sweden)

    C. L. Croskey

    2006-07-01

    Full Text Available Langmuir probe electron and ion measurements from four instrumented rockets flown during the MaCWAVE (Mountain and Convective Waves Ascending VErtically program are reported. Two of the rockets were launched from Andøya Rocket Range, Norway, in the summer of 2002. Electron scavenging by ice particulates produced reductions of the electron density in both sharp narrow (≈1–2 km layers and as a broad (≈13 km depletion. Small-scale irregularities were observed in the altitude regions of both types of electron depletion. The scale of the irregularities extended to wavelengths comparable to those used by ground-based radars in observing PMSE. In regions where ice particles were not present, analysis of the spectral signatures provided reasonable estimates of the energy deposition from breaking gravity waves.

    Two more instrumented rockets were flown from Esrange, Sweden, in January 2003. Little turbulence or energy deposition was observed during one flight, but relatively large values were observed during the other flight. The altitude distribution of the observed turbulence was consistent with observations of a semidiurnal tide and gravity wave instability effects as determined by ground-based lidar and radar measurements and by falling sphere measurements of the winds and temperatures (Goldberg et al., 2006; Williams et al., 2006.

  14. In-situ electron and ion measurements and observed gravity wave effects in the polar mesosphere during the MaCWAVE program

    Directory of Open Access Journals (Sweden)

    C. L. Croskey

    2006-07-01

    Full Text Available Langmuir probe electron and ion measurements from four instrumented rockets flown during the MaCWAVE (Mountain and Convective Waves Ascending VErtically program are reported. Two of the rockets were launched from Andøya Rocket Range, Norway, in the summer of 2002. Electron scavenging by ice particulates produced reductions of the electron density in both sharp narrow (≈1–2 km layers and as a broad (≈13 km depletion. Small-scale irregularities were observed in the altitude regions of both types of electron depletion. The scale of the irregularities extended to wavelengths comparable to those used by ground-based radars in observing PMSE. In regions where ice particles were not present, analysis of the spectral signatures provided reasonable estimates of the energy deposition from breaking gravity waves. Two more instrumented rockets were flown from Esrange, Sweden, in January 2003. Little turbulence or energy deposition was observed during one flight, but relatively large values were observed during the other flight. The altitude distribution of the observed turbulence was consistent with observations of a semidiurnal tide and gravity wave instability effects as determined by ground-based lidar and radar measurements and by falling sphere measurements of the winds and temperatures (Goldberg et al., 2006; Williams et al., 2006.

  15. HPC - Platforms Penta Chart

    Energy Technology Data Exchange (ETDEWEB)

    Trujillo, Angelina Michelle [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2015-10-08

    Strategy, Planning, Acquiring- very large scale computing platforms come and go and planning for immensely scalable machines often precedes actual procurement by 3 years. Procurement can be another year or more. Integration- After Acquisition, machines must be integrated into the computing environments at LANL. Connection to scalable storage via large scale storage networking, assuring correct and secure operations. Management and Utilization – Ongoing operations, maintenance, and trouble shooting of the hardware and systems software at massive scale is required.

  16. Unpolarized nucleon structure studies utilizing polarized electromagnetic probes

    International Nuclear Information System (INIS)

    Arrington, J.

    2009-01-01

    By the mid-1980s, measurements of the nucleon form factors had reached a stage where only slow, incremental progress was possible using unpolarized electron scattering. The development of high quality polarized beams, polarized targets, and recoil polarimeters led to a renaissance in the experimental program. I provide an overview of the changes in the field in the last ten years, which were driven by the dramatically improved data made possible by a new family of tools to measure polarization observables

  17. COMPASS polarized target for Drell-Yan

    CERN Document Server

    Pešek, M

    2014-01-01

    In the COMPASS Drell–Yan experiment the pion beam with momen tum of 190 GeV/ c and in- tensity up to 10 8 pions/s will interact with transversely polarized proton t arget producing muon pair via Drell–Yan process. The solid-state NH 3 will be polarized by dynamic nuclear polar- ization. Maximum polarization reached during data taking i s expected to be up to 90%. The non-interacting beam and other particles produced inside t he target will be stopped in the hadron absorber after the target. Two target cells, sepparated by a 20 cm gap in between, each 55 cm long and 4 cm in diameter give the target material volume about 691 cm 3 . The target platform needs to be moved by 2.3 m in upstream dire ction from the position used in previous experiments in order to accomodate the absorber. D uring the beam time higher radiation is expected in the area of the control room. Thus a new target r emote control system is needed. The target magnet is undergoing a substantial upgrade. Drell–Yan data taking is expected t...

  18. The Prodiguer Messaging Platform

    Science.gov (United States)

    Denvil, S.; Greenslade, M. A.; Carenton, N.; Levavasseur, G.; Raciazek, J.

    2015-12-01

    CONVERGENCE is a French multi-partner national project designed to gather HPC and informatics expertise to innovate in the context of running French global climate models with differing grids and at differing resolutions. Efficient and reliable execution of these models and the management and dissemination of model output are some of the complexities that CONVERGENCE aims to resolve.At any one moment in time, researchers affiliated with the Institut Pierre Simon Laplace (IPSL) climate modeling group, are running hundreds of global climate simulations. These simulations execute upon a heterogeneous set of French High Performance Computing (HPC) environments. The IPSL's simulation execution runtime libIGCM (library for IPSL Global Climate Modeling group) has recently been enhanced so as to support hitherto impossible realtime use cases such as simulation monitoring, data publication, metrics collection, simulation control, visualizations … etc. At the core of this enhancement is Prodiguer: an AMQP (Advanced Message Queue Protocol) based event driven asynchronous distributed messaging platform. libIGCM now dispatches copious amounts of information, in the form of messages, to the platform for remote processing by Prodiguer software agents at IPSL servers in Paris. Such processing takes several forms: Persisting message content to database(s); Launching rollback jobs upon simulation failure; Notifying downstream applications; Automation of visualization pipelines; We will describe and/or demonstrate the platform's: Technical implementation; Inherent ease of scalability; Inherent adaptiveness in respect to supervising simulations; Web portal receiving simulation notifications in realtime.

  19. "Platform switching": Serendipity

    Directory of Open Access Journals (Sweden)

    N Kalavathy

    2014-01-01

    Full Text Available Implant dentistry is the latest developing field in terms of clinical techniques, research, material science and oral rehabilitation. Extensive work is being done to improve the designing of implants in order to achieve better esthetics and function. The main drawback with respect to implant restoration is achieving good osseointegration along with satisfactory stress distribution, which in turn will improve the prognosis of implant prosthesis by reducing the crestal bone loss. Many concepts have been developed with reference to surface coating of implants, surgical techniques for implant placement, immediate and delayed loading, platform switching concept, etc. This article has made an attempt to review the concept of platform switching was in fact revealed accidentally due to the nonavailability of the abutment appropriate to the size of the implant placed. A few aspect of platform switching, an upcoming idea to reduce crestal bone loss have been covered. The various methods used for locating and preparing the data were done through textbooks, Google search and related articles.

  20. Current meter components and other data from FIXED PLATFORMS in support of the Physical Oceanography Field Program Offshore North Carolina from 1992-02-22 to 1993-02-18 (NODC Accession 9300089)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Current meter components data were collected from FIXED PLATFORMS from 22 February 1992 to 18 February 1993. Data were collected by the Science Applications, Inc....

  1. Temperature profile data collected using XBTs from the TOKYO MARU and other platforms from the Pacific Ocean during the Thermal Structure Monitoring Program in the Pacific (TRANSPAC) project, 1989-08-28 to 1990-07-08 (NODC Accession 9000204)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Temperature profile data were collected using bathythermograph (BT/XBT) casts from TOKYO MARU and other platforms in the Pacific Ocean from August 28, 1989 to July...

  2. Temperature profile from NOAA Ship RESEARCHER and other platforms as part of the ARP (Global Atmospheric Research Program) Atlantic Tropical Experiment from 1974-08-28 to 1974-09-20 (NODC Accession 7800314)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Temperature profile data were collected using BT and XBT from NOAA Ship RESEARCHER and other platforms in the TOGA area - Atlantic from 28 August 1974 to 20...

  3. Temperature profile data collected using XBTs from the SVENJA and other platforms from the Pacific Ocean during the Thermal Structure Monitoring Program in the Pacific (TRANSPAC) project, 1989-04-24 to 1990-02-07 (NODC Accession 9000063)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Temperature profile data were collected using bathythermograph (BT/XBT) casts from SVENJA and other platforms in the Pacific Ocean from April 24, 1989 to February 7,...

  4. Polarized atomic beams for targets

    International Nuclear Information System (INIS)

    Grueebler, W.

    1984-01-01

    The basic principle of the production of polarized atomic hydrogen and deuterium beams are reviewed. The status of the present available polarization, density and intensity are presented. The improvement of atomic beam density by cooling the hydrogen atoms to low velocity is discussed. The possible use of polarized atomic beams as targets in storage rings is shown. It is proposed that polarized atomic beams can be used to produce polarized gas targets with high polarization and greatly improved density

  5. Polarized scintillator targets

    Science.gov (United States)

    van den Brandt, B.; Bunyatova, E. I.; Hautle, P.; Konter, J. A.; Mango, S.

    2000-05-01

    The hydrogen nuclei in an organic scintillator have been polarized to more than 80% and the deuterons in its fully deuterated version to 24%. The scintillator, doped with TEMPO, has been polarized dynamically in a field of 2.5 T in a vertical dilution refrigerator in which a plastic lightguide transports the scintillation light from the sample in the mixing chamber to a photomultiplier outside the cryostat. Sizeable solid samples with acceptable optical properties and light output have been prepared and successfully operated as "live" polarized targets in nuclear physics experiments.

  6. Polarized scintillator targets

    Energy Technology Data Exchange (ETDEWEB)

    Brandt, B. van den E-mail: vandenbrandt@psi.ch; Bunyatova, E.I.; Hautle, P.; Konter, J.A.; Mango, S

    2000-05-21

    The hydrogen nuclei in an organic scintillator have been polarized to more than 80% and the deuterons in its fully deuterated version to 24%. The scintillator, doped with TEMPO, has been polarized dynamically in a field of 2.5 T in a vertical dilution refrigerator in which a plastic lightguide transports the scintillation light from the sample in the mixing chamber to a photomultiplier outside the cryostat. Sizeable solid samples with acceptable optical properties and light output have been prepared and successfully operated as 'live' polarized targets in nuclear physics experiments.

  7. Heidelberg polarized alkali source

    International Nuclear Information System (INIS)

    Kraemer, D.; Steffens, E.; Jaensch, H.; Philipps Universitaet, Marburg, Germany)

    1984-01-01

    A new atomic beam type polarized alkali ion source has been installed at Heidelberg. In order to improve the beam polarization considerably optical pumping is applied in combination with an adiabatic medium field transition which results in beams in single hyperfine sublevels. The m state population is determined by laser-induced fluorescence spectroscopy. Highly polarized beams (P/sub s/ > 0.9, s = z, zz) with intensities of 30 to 130 μA can be extracted for Li + and Na + , respectively

  8. Electrically tunable polarizer based on 2D orthorhombic ferrovalley materials

    Science.gov (United States)

    Shen, Xin-Wei; Tong, Wen-Yi; Gong, Shi-Jing; Duan, Chun-Gang

    2018-03-01

    The concept of ferrovalley materials has been proposed very recently. The existence of spontaneous valley polarization, resulting from ferromagnetism, in such hexagonal 2D materials makes nonvolatile valleytronic applications realizable. Here, we introduce a new member of ferrovalley family with orthorhombic lattice, i.e. monolayer group-IV monochalcogenides (GIVMs), in which the intrinsic valley polarization originates from ferroelectricity, instead of ferromagnetism. Combining the group theory analysis and first-principles calculations, we demonstrate that, different from the valley-selective circular dichroism in hexagonal lattice, linearly polarized optical selectivity for valleys exists in the new type of ferrovalley materials. On account of the distinctive property, a prototype of electrically tunable polarizer is realized. In the ferrovalley-based polarizer, a laser beam can be optionally polarized in x- or y-direction, depending on the ferrovalley state controlled by external electric fields. Such a device can be further optimized to emit circularly polarized radiation with specific chirality and to realize the tunability for operating wavelength. Therefore, we show that 2D orthorhombic ferrovalley materials are the promising candidates to provide an advantageous platform to realize the polarizer driven by electric means, which is of great importance in extending the practical applications of valleytronics.

  9. Polarization measurement in the COMPASS polarized target

    CERN Document Server

    Kondo, K; Baum, G; Berglund, P; Doshita, N; Gautheron, F; Görtz, S; Hasegawa, T; Horikawa, N; Ishimoto, S; Iwata, T; Kisselev, Yu V; Koivuniemi, J H; Le Goff, J M; Magnon, A; Meyer, W; Reicherz, G; Matsuda, T

    2004-01-01

    Continuous wave nuclear magnetic resonance (NMR) is used to determine the target polarization in the COMPASS experiment. The system is made of the so-called Liverpool Q-meters, Yale-cards, and VME modules for data taking and system controlling. In 2001 the NMR coils were embedded in the target material, while in 2002 and 2003 the coils were mounted on the outer surface of the target cells to increase the packing factor of the material. Though the error of the measurement became larger with the outer coils than with the inner coils, we have performed stable measurements throughout the COMPASS run time for 3 years. The maximum polarization was +57% and -53% as the average in the target cells.

  10. The Balloon-borne Large Aperture Telescope for Polarization - BLASTPol

    Science.gov (United States)

    Devlin, Mark

    We are proposing a comprehensive program to study the link between Galactic magnetic fields and star formation. After decades of study, the physical processes regulating star formation still remain poorly understood. Large-scale observations of star forming regions provide counts of the number of dense clouds each of which will eventually evolve into tens to hundreds of stars. However, when simple models of gravitational collapse are applied to the clouds they yield a Galactic star formation rate (SFR) which is many times what is actually observed. Some process or combination of processes must be slowing the collapse of the clouds. The two prevailing theories involve turbulence which prevents the effective dissipation of energy and Galactic magnetic fields which are captured and squeezed by the collapsing cloud provide a mechanism for mechanical support. Understanding these effects fits very well the SMD 2010 Science Plan's Cosmic Origins program. The Balloon-borne Large Aperture Telescope - BLAST was originally designed to conduct confusion-limited and wide-area extragalactic and Galactic surveys at submillimeter wavelengths from a long-duration balloon (LDB) platform. These wavelengths are impossible or very difficult to observe from even the best groundbased telescope sites. After a series of successful flights (Ft. Sumner 2003, Sweden 2005, and Antarctica 2006) resulting in over 25 publications, BLAST was converted to BLASTPol. The combination of a polarizing grid in front of each of the 266 feed horns at 250, 350 and 500 micron with a stepped Half Wave Plate (HWP) provided a quick and inexpensive way to make initial measurements of polarized dust emission in star forming regions. By mapping polarization from dust grains aligned with respect to their local magnetic field, the field orientation (projected on the sky) can be traced. The development of the Next Generation BLASTPol instrument is now complete. It has increased spatial resolution (22 arcseconds at

  11. Platform computing powers enterprise grid

    CERN Document Server

    2002-01-01

    Platform Computing, today announced that the Stanford Linear Accelerator Center is using Platform LSF 5, to carry out groundbreaking research into the origins of the universe. Platform LSF 5 will deliver the mammoth computing power that SLAC's Linear Accelerator needs to process the data associated with intense high-energy physics research (1 page).

  12. Contemporary Internet of Things platforms

    OpenAIRE

    Mineraud, Julien; Mazhelis, Oleksiy; Su, Xiang; Tarkoma, Sasu

    2015-01-01

    This document regroups a representative, but non-exhaustive, list of contemporary IoT platforms. The platforms are ordered alphabetically. The aim of this document is to provide the a quick review of current IoT platforms, as well as relevant information.

  13. Lattice QCD simulations using the OpenACC platform

    International Nuclear Information System (INIS)

    Majumdar, Pushan

    2016-01-01

    In this article we will explore the OpenACC platform for programming Graphics Processing Units (GPUs). The OpenACC platform offers a directive based programming model for GPUs which avoids the detailed data flow control and memory management necessary in a CUDA programming environment. In the OpenACC model, programs can be written in high level languages with OpenMP like directives. We present some examples of QCD simulation codes using OpenACC and discuss their performance on the Fermi and Kepler GPUs. (paper)

  14. Platforms, specifications and decisions

    NARCIS (Netherlands)

    Bergstra, J.A.

    Program variables in a call-by-value mode are added to the elementary syntax of program algebra. Only very simple data are considered: finite sequences of bits. The meaning of program variables, data type constants and assignments in a call-by-value regime is given by means of a translation into

  15. Analysis of offshore platforms lifting with fixed pile structure type (fixed platform) based on ASD89

    Science.gov (United States)

    Sugianto, Agus; Indriani, Andi Marini

    2017-11-01

    Platform construction GTS (Gathering Testing Sattelite) is offshore construction platform with fix pile structure type/fixed platform functioning to support the mining of petroleum exploitation. After construction fabrication process platform was moved to barges, then shipped to the installation site. Moving process is generally done by pull or push based on construction design determined when planning. But at the time of lifting equipment/cranes available in the work area then the moving process can be done by lifting so that moving activity can be implemented more quickly of work. This analysis moving process of GTS platform in a different way that is generally done to GTS platform types by lifting using problem is construction reinforcement required, so the construction can be moved by lifting with analyzing and checking structure working stress that occurs due to construction moving process by lifting AISC code standard and analysis using the SAP2000 structure analysis program. The analysis result showed that existing condition cannot be moved by lifting because stress ratio is above maximum allowable value that is 0.950 (AISC-ASD89). Overstress occurs on the member 295 and 324 with stress ratio value 0.97 and 0.95 so that it is required structural reinforcement. Box plate aplication at both members so that it produces stress ratio values 0.78 at the member 295 and stress ratio of 0.77 at the member 324. These results indicate that the construction have qualified structural reinforcement for being moved by lifting.

  16. Dynamic nuclear spin polarization

    Energy Technology Data Exchange (ETDEWEB)

    Stuhrmann, H.B. [GKSS-Forschungszentrum Geesthacht GmbH (Germany)

    1996-11-01

    Polarized neutron scattering from dynamic polarized targets has been applied to various hydrogenous materials at different laboratories. In situ structures of macromolecular components have been determined by nuclear spin contrast variation with an unprecedented precision. The experiments of selective nuclear spin depolarisation not only opened a new dimension to structural studies but also revealed phenomena related to propagation of nuclear spin polarization and the interplay of nuclear polarisation with the electronic spin system. The observation of electron spin label dependent nuclear spin polarisation domains by NMR and polarized neutron scattering opens a way to generalize the method of nuclear spin contrast variation and most importantly it avoids precontrasting by specific deuteration. It also likely might tell us more about the mechanism of dynamic nuclear spin polarisation. (author) 4 figs., refs.

  17. Time Domain Induced Polarization

    DEFF Research Database (Denmark)

    Fiandaca, Gianluca; Auken, Esben; Christiansen, Anders Vest

    2012-01-01

    Time-domain-induced polarization has significantly broadened its field of reference during the last decade, from mineral exploration to environmental geophysics, e.g., for clay and peat identification and landfill characterization. Though, insufficient modeling tools have hitherto limited the use...... of time-domaininduced polarization for wider purposes. For these reasons, a new forward code and inversion algorithm have been developed using the full-time decay of the induced polarization response, together with an accurate description of the transmitter waveform and of the receiver transfer function......%. Furthermore, the presence of low-pass filters in time-domain-induced polarization instruments affects the early times of the acquired decays (typically up to 100 ms) and has to be modeled in the forward response to avoid significant loss of resolution. The developed forward code has been implemented in a 1D...

  18. Polarized proton colliders

    International Nuclear Information System (INIS)

    Roser, T.

    1995-01-01

    High energy polarized beam collisions will open up the unique physics opportunities of studying spin effects in hard processes. This will allow the study of the spin structure of the proton and also the verification of the many well documented expectations of spin effects in perturbative QCD and parity violation in W and Z production. Proposals for polarized proton acceleration for several high energy colliders have been developed. A partial Siberian Snake in the AGS has recently been successfully tested and full Siberian Snakes, spin rotators, and polarimeters for RHIC are being developed to make the acceleration of polarized beams to 250 GeV possible. This allows for the unique possibility of colliding two 250 GeV polarized proton beams at luminosities of up to 2 x 10 32 cm -2 s -1

  19. Cross-platform wireless sensor network development

    DEFF Research Database (Denmark)

    Hansen, Morten Tranberg; Kusy, Branislav

    Design and development of wireless sensor network applications adds an additional layer of complexity to traditional computer systems. The developer needs to be an expert in resource constrained embedded devices as well as traditional desktop computers. We propose Tinylnventor, an open......-source development environment that takes a holistic approach to implementing sensor network applications. Users build applications using a drag-and-drop visual programming language Open Blocks, a language that Google selected for its App Inventor for Android. Tinylnventor uses cross-platform programming concepts......, such as threads and common network operations, to provide a unified environment from which it generates application binaries for the respective platforms. We demonstrate through an application example that Tinylnventor is both simple to use and powerful in expressing complex applications....

  20. Plasma polarization spectroscopy

    International Nuclear Information System (INIS)

    Iwamae, Atsushi; Horimoto, Yasuhiro; Fujimoto, Takashi; Hasegawa, Noboru; Sukegawa, Kouta; Kawachi, Tetsuya

    2005-01-01

    The electron velocity distribution function (EVDF) in plasma can be anisotropic in laser-produced plasmas. We have developed a new technique to evaluate the polarization degree of the emission lines in the extreme vacuum ultra violet wavelength region. The polarization of the emission lines and the continuums from the lithium-like nitrogen and from helium- and hydrogen-like carbon in recombining plasma is evaluated. Particle simulation in the velocity space gives the time scale for relaxation of anisotropic EVDFs. (author)

  1. Ultracold Polar Molecules

    Science.gov (United States)

    2016-04-01

    AFRL-AFOSR-UK-TR-2016-0005 Ultracold Polar Molecules Jeremy Hutson UNIVERSITY OF DURHAM Final Report 04/01/2016 DISTRIBUTION A: Distribution approved...DATES COVERED (From - To) 15-Jan-2010 to 14-Jul-2015 4. TITLE AND SUBTITLE Final Report on Grant FA8655-10-1-3033 on Ultracold Polar Molecules 5a...formation of ultracold 87RbCs molecules in their rovibrational ground state by magnetoassociation followed by STIRAP, resulting in 14 papers acknowledging

  2. Programming

    International Nuclear Information System (INIS)

    Jackson, M.A.

    1982-01-01

    The programmer's task is often taken to be the construction of algorithms, expressed in hierarchical structures of procedures: this view underlies the majority of traditional programming languages, such as Fortran. A different view is appropriate to a wide class of problem, perhaps including some problems in High Energy Physics. The programmer's task is regarded as having three main stages: first, an explicit model is constructed of the reality with which the program is concerned; second, this model is elaborated to produce the required program outputs; third, the resulting program is transformed to run efficiently in the execution environment. The first two stages deal in network structures of sequential processes; only the third is concerned with procedure hierarchies. (orig.)

  3. Programming

    CERN Document Server

    Jackson, M A

    1982-01-01

    The programmer's task is often taken to be the construction of algorithms, expressed in hierarchical structures of procedures: this view underlies the majority of traditional programming languages, such as Fortran. A different view is appropriate to a wide class of problem, perhaps including some problems in High Energy Physics. The programmer's task is regarded as having three main stages: first, an explicit model is constructed of the reality with which the program is concerned; second, this model is elaborated to produce the required program outputs; third, the resulting program is transformed to run efficiently in the execution environment. The first two stages deal in network structures of sequential processes; only the third is concerned with procedure hierarchies.

  4. Polarized lepton-nucleon scattering

    Energy Technology Data Exchange (ETDEWEB)

    Hughes, E. [Stanford Univ., CA (United States)

    1994-12-01

    The author provides a summary of the proposed and published statistical (systematic) uncertainties from the world experiments on nucleon spin structure function integrals. By the time these programs are complete, there will be a vast resource of data on nucleon spin structure functions. Each program has quite different experimental approaches regarding the beams, targets, and spectrometers thus ensuring systematically independent tests of the spin structure function measurements. Since the field of spin structure function measurements began, there has been a result appearing approximately every five years. With advances in polarized target technology and high polarization in virtually all of the lepton beams, results are now coming out each year; this is a true signature of the growth in the field. Hopefully, the experiments will provide a consistent picture of nucleon spin structure at their completion. In summary, there are still many open questions regarding the internal spin structure of the nucleon. Tests of QCD via the investigation of the Bjorken sum rule is a prime motivator for the field, and will continue with the next round of precision experiments. The question of the origin of spin is still a fundamental problem. Researchers hope is that high-energy probes using spin will shed light on this intriguing mystery, in addition to characterizing the spin structure of the nucleon.

  5. Hsp Polarization Verification

    Science.gov (United States)

    Bless, Robert

    1991-07-01

    This proposal defines the procedure for determining the instrumental polarization of the polarimetric IDT (IDT#1, POL) on the HSP. 1 of 2 unpolarized standard stars wil be observed using various filter-polarizer combinations. These observations will permit the instrumental polarization to be calibrated. The instrumental polarization must be determined to a high precision in order to vectoriallly remove it from HSP polarization observations to determine the actual astronomical polarization. Final run of proposal will look at one of 2 possible stars previously observed to get another look at the throughput. Revision History: Mark H. Slovak 8/30/88 Translated to V2 proposal instructions (RPSS V6.2) S. Laurent 1/20/89 Updated: Sally Laurent 2/24/89, 3/20/89, 4/13/89, 5/12/89 Modified: P. Stanley 1/15/90 - change to use CTA selected targets only; Fixes for aberration problem - SALM 7/30/90; Based on SV/HSP 1386. New submission changed targets and revised scheduling strategy. Revised: 26 Aug 92 J. Dolan, L. Walter, P. Reppert want to re-run the proposal (3985) one last time to bring down errors.

  6. A Workflow Platform for Simulation on Grids

    OpenAIRE

    Nguyen, Toan; Trifan, Laurentiu; Desideri, Jean-Antoine

    2011-01-01

    International audience; This paper presents the design, implementation and deployment of a simulation platform based on distributed workflows. It supports the smooth integration of existing software, e.g., Matlab, Scilab, Python, OpenFOAM, ParaView and user-defined programs. Additional features include the support for application-level fault-tolerance and exception-handling, i.e., resilience, and the orchestrated execution of distributed codes on remote high-performance clusters.

  7. Platform deck. Plattformdekk

    Energy Technology Data Exchange (ETDEWEB)

    Gudmestad, O.T.; Warland, T.Aa.; Coker, J.W.A.; Stead, B.

    1992-03-30

    The invention deals with a platform deck comprising a trusswork deck section and a deck section made of plates designed for being welded together for the final concreting. The deck structure is designed for being connected to at least two shafts, and can include equipment, needing protection against pollution, or natural ventilation systems. Each of the two sections mentioned can be built by different contractors and finally assembled onshore or offshore. Both of the sections are equipped with corresponding upper and lower supporting elements for simplifying the assembling procedure. 4 figs.

  8. Polarized Light Microscopy

    Science.gov (United States)

    Frandsen, Athela F.

    2016-01-01

    Polarized light microscopy (PLM) is a technique which employs the use of polarizing filters to obtain substantial optical property information about the material which is being observed. This information can be combined with other microscopy techniques to confirm or elucidate the identity of an unknown material, determine whether a particular contaminant is present (as with asbestos analysis), or to provide important information that can be used to refine a manufacturing or chemical process. PLM was the major microscopy technique in use for identification of materials for nearly a century since its introduction in 1834 by William Fox Talbot, as other techniques such as SEM (Scanning Electron Microscopy), FTIR (Fourier Transform Infrared spectroscopy), XPD (X-ray Powder Diffraction), and TEM (Transmission Electron Microscopy) had not yet been developed. Today, it is still the only technique approved by the Environmental Protection Agency (EPA) for asbestos analysis, and is often the technique first applied for identification of unknown materials. PLM uses different configurations in order to determine different material properties. With each configuration additional clues can be gathered, leading to a conclusion of material identity. With no polarizing filter, the microscope can be used just as a stereo optical microscope, and view qualities such as morphology, size, and number of phases. With a single polarizing filter (single polars), additional properties can be established, such as pleochroism, individual refractive indices, and dispersion staining. With two polarizing filters (crossed polars), even more can be deduced: isotropy vs. anisotropy, extinction angle, birefringence/degree of birefringence, sign of elongation, and anomalous polarization colors, among others. With the use of PLM many of these properties can be determined in a matter of seconds, even for those who are not highly trained. McCrone, a leader in the field of polarized light microscopy, often

  9. Analysis of CMOS Compatible Cu-Based TM-Pass Optical Polarizer

    KAUST Repository

    Ng, Tien Khee

    2012-02-10

    A transverse-magnetic-pass (TM-pass) optical polarizer based on Cu complementary metal-oxide-semiconductor technology platform is proposed and analyzed using the 2-D method-of-lines numerical model. In designing the optimum configuration for the polarizer, it was found that the metal-insulator-metal (MIM) polarizer structure is superior compared to the insulator-metal-insulator polarizer structure due to its higher polarization extinction ratio (PER) and low insertion loss. An optimized MIM TM-pass polarizer exhibits simulated long wavelength pass filter characteristics of > ?1.2 ?m, with fundamental TM 0 and TE 0 mode transmissivity of >70% and <5%, respectively, and with PER ?11.5 dB in the wavelength range of 1.2-1.6 ?m. The subwavelength and submicrometer features of this TM-polarizer are potentially suitable for compact and low power photonics integrated circuit implementation on silicon-based substrates. © 1989-2012 IEEE.

  10. NSIDC's passive microwave satellite record: The story behind 30 years of data across multiple satellite platforms

    Science.gov (United States)

    Scott, D. J.; Brandt, M.; Savoie, M. H.; Stewart, J. S.

    2016-12-01

    The National Snow and Ice Data Center (NSIDC) Distributed Active Archive Center (DAAC) has been producing and distributing passive microwave snow and ice data sets from the Special Sensor Microwave Imager (SSM/I) and Special Sensor Microwave Imager/Sounder (SSMIS) for over two decades. Aboard the Defense Meteorological Satellite Program (DMSP) platforms, SSM/I and SSMIS have been operating across eight different orbiting DMSP satellites since 1987, providing an invaluable 30 year record for snow and ice climate data studies. Each sensor has performed within or beyond its expected life cycle, ultimately resulting in a transition across platforms to continue the data record. On occasion the satellites have failed unexpectedly, requiring an unplanned need for science and data management to come together and adjust production code and services to get the data back online in a timely fashion. In recent years, this has become a greater importance as climate blogging sites have increased the visibility of near-real-time passive microwave products to communicate the current changes in the Polar Regions. This presentation summarizes the history and most recent activities surrounding satellite transitions, including the scientific assessment and development required in maintaining a streamlined data record across multiple sensors. In addition, we examine challenges in long-term provenance as well as the considerations and decisions made based on value added products utilizing these data, as well as cryospheric research and general public needs.

  11. Exploiting multi-level parallelism in streaming applications for heterogeneous platforms with GPUs

    OpenAIRE

    Balevic, Ana

    2013-01-01

    Heterogeneous computing platforms support the traditional types of parallelism, such as e.g., instruction-level, data, task, and pipeline parallelism, and provide the opportunity to exploit a combination of different types of parallelism at different platform levels. The architectural diversity of platform components makes tapping into the platform potential a challenging programming task. This thesis makes an important step in this direction by introducing a novel methodology for automatic g...

  12. The evolution of tensor polarization

    International Nuclear Information System (INIS)

    Huang, H.; Lee, S.Y.; Ratner, L.

    1993-01-01

    By using the equation of motion for the vector polarization, the spin transfer matrix for spin tensor polarization, the spin transfer matrix for spin tensor polarization is derived. The evolution equation for the tensor polarization is studied in the presence of an isolate spin resonance and in the presence of a spin rotor, or snake

  13. The CERN Neutrino Platform

    CERN Document Server

    Bordoni, Stefania

    2018-01-01

    The long-baseline neutrino programme has been classified as one of the four highest-priority sci- entific objectives in 2013 by the European Strategy for Particle Physics. The Neutrino Platform is the CERN venture to foster and support the next generation of accelerator-based neutrino os- cillation experiments. Part of the present CERN Medium-Term Plan, the Neutrino Platform provide facilities to develop and prototype the next generation of neutrino detectors and contribute to unify the European neu- trino community towards the US and Japanese projects. A significative effort is made on R&D; for LAr TPC technologies: two big LAr TPC prototypes for the DUNE far detector are under con- struction at CERN. Those detectors will be exposed in 2018 to an entirely new and NP-dedicated beam-line from the SPS which will provide electron, muon and hadron beams with energies in the range of sub-GeV to a few GeV. Other projects are also presently under development: one can cite the refurbishing and shipping to the US ...

  14. Platform for Action: update.

    Science.gov (United States)

    1995-01-01

    The Center for Women's Global Leadership (CWGL) has collaborated in the preparation of amendments and strategies designed to withstand the challenges being posed to the Platform for Action of the Fourth World Conference on Women. Specific challenges include the inappropriate use of the word "universal" to modify "human rights." This implies that some human rights are less than universal. The strategy proposed is to accept the use of the word "universal" in this context only when it affirms principles of universality contained in the Vienna Programme of Action and not where its use would restrict the rights to which women are entitled. A second concern is over the use of the word "equity" rather than "equality" when referring to gender relations. The use of these terms will be carefully monitored to insure that "equity" not be used to undermine the principle of gender equality. The third concern is the efforts of some governments to hinder the integration of women's human rights throughout the UN system. Such efforts will be opposed. Fourth, the CWGL will seek the inclusion of language which recognizes the barriers that different groups of women face when trying to secure their rights. Finally, the CWGL will propose inclusion of language recognizing and protecting sexual orientation rights. The CWGL is also going to work to translate the abstract language of the Platform for Action into political organizing potential to insure that governments will follow through on their agreements.

  15. Multimedia Capable Distributed Object Platform | Baichoo ...

    African Journals Online (AJOL)

    Multimedia Capable Distributed Object Platform. ... This paper discusses the design and implementation of a multimediacapable distributed object platform, using a low-level platform GOPI (General Object Platform ... Keywords: Multimedia; GOPI; IDL; CORBA; Quality of Service; Middleware; Distributed Systems.

  16. Polarized protons at RHIC

    International Nuclear Information System (INIS)

    Tannenbaum, M.J.

    1990-12-01

    The Physics case is presented for the use of polarized protons at RHIC for one or two months each year. This would provide a facility with polarizations of approx-gt 50% high luminosity ∼2.0 x 10 32 cm -2 s -1 , the possibility of both longitudinal and transverse polarization at the interaction regions, and frequent polarization reversal for control of systematic errors. The annual integrated luminosity for such running (∼10 6 sec per year) would be ∫ Ldt = 2 x 10 38 cm -2 -- roughly 20 times the total luminosity integrated in ∼ 10 years of operation of the CERN Collider (∼10 inverse picobarns, 10 37 cm -2 ). This facility would be unique in the ability to perform parity-violating measurements and polarization test of QCD. Also, the existence of p-p collisions in a new energy range would permit the study of ''classical'' reactions like the total cross section and elastic scattering, etc., and serve as a complement to measurements from p-bar p colliders. 11 refs

  17. The Bochum Polarized Target

    International Nuclear Information System (INIS)

    Reicherz, G.; Goertz, S.; Harmsen, J.; Heckmann, J.; Meier, A.; Meyer, W.; Radtke, E.

    2001-01-01

    The Bochum 'Polarized Target' group develops the target material 6 LiD for the COMPASS experiment at CERN. Several different materials like alcohols, alcanes and ammonia are under investigation. Solid State Targets are polarized in magnetic fields higher than B=2.5T and at temperatures below T=1K. For the Dynamic Nuclear Polarization process, paramagnetic centers are induced chemically or by irradiation with ionizing beams. The radical density is a critical factor for optimization of polarization and relaxation times at adequate magnetic fields and temperatures. In a high sensitive EPR--apparatus, an evaporator and a dilution cryostat with a continuous wave NMR--system, the materials are investigated and optimized. To improve the polarization measurement, the Liverpool NMR-box is modified by exchanging the fixed capacitor for a varicap diode which not only makes the tuning very easy but also provides a continuously tuned circuit. The dependence of the signal area upon the circuit current is measured and it is shown that it follows a linear function

  18. In-line Fiber Polarizer

    OpenAIRE

    Perumalsamy, Priya

    1998-01-01

    Polarizers and polarization devices are important components in fiber optic communication and sensor systems. There is a growing need for efficient low loss components that are compatible with optical fibers. An all fiber in-line polarizer is a more desirable alternative that could be placed at appropriate intervals along communication links. An in-line fiber polarizer was fabricated and tested. The in-line fiber polarizer operates by coupling optical energy propagatin...

  19. Platform Performance and Challenges - using Platforms in Lego Company

    DEFF Research Database (Denmark)

    Munk, Lone; Mortensen, Niels Henrik

    2009-01-01

    This article studies the performance and challenges of using nine implemented product platforms in LEGO Company. Most of these do produce results, but do not meet their goals due to challenges in their usage in the daily product. The main challenges are that the platforms are not being used...... needs focus on the incentive of using the platform. This problem lacks attention in literature, as well as industry, where assessment criteria do not cover this aspect. Therefore, we recommend including user incentive in platform assessment criteria to these challenges. Concrete solution elements...

  20. Proceedings of the workshop on polarized targets in storage rings

    International Nuclear Information System (INIS)

    Holt, R.J.

    1984-08-01

    Polarization phenomena have played an increasingly important part in the study of nuclei and nucleons in recent years. Polarization studies have been hampered by the relatively few and rather fragile polarized targets which are presently available. The concept of polarized gas targets in storage rings opens a much wider range of possibilities than is available in the external target geometry. This novel method will represent a considerable advance in nuclear physics and will continue to receive much attention in plans for future facilities. An internal, polarized-target station is being planned for the cooler ring at the Indiana University Cyclotron Facility. Internal targets are compatible with recent designs of electron accelerators proposed by the Massachusetts Institute of Technology and the Southeastern Universities Research Association. The key to nuclear-science programs based on internal targets pivots on recent developments in polarized atomic beam methods, which include the more recent laser-driven polarized targets. The workshop drew together a unique group of physicists in the fields of high-energy, nuclear and atomic physics. The meeting was organized in a manner that stimulated discussion among the 58 participants and focused on developments in polarized target technology and the underlying atomic physics. An impressive array of future possibilities for polarized targets as well as current developments in polarized target technology were discussed at the workshop. Abstracts of individual items from the workshop were prepared separately for the data base

  1. Proceedings of the workshop on polarized targets in storage rings

    Energy Technology Data Exchange (ETDEWEB)

    Holt, R.J. (ed.)

    1984-08-01

    Polarization phenomena have played an increasingly important part in the study of nuclei and nucleons in recent years. Polarization studies have been hampered by the relatively few and rather fragile polarized targets which are presently available. The concept of polarized gas targets in storage rings opens a much wider range of possibilities than is available in the external target geometry. This novel method will represent a considerable advance in nuclear physics and will continue to receive much attention in plans for future facilities. An internal, polarized-target station is being planned for the cooler ring at the Indiana University Cyclotron Facility. Internal targets are compatible with recent designs of electron accelerators proposed by the Massachusetts Institute of Technology and the Southeastern Universities Research Association. The key to nuclear-science programs based on internal targets pivots on recent developments in polarized atomic beam methods, which include the more recent laser-driven polarized targets. The workshop drew together a unique group of physicists in the fields of high-energy, nuclear and atomic physics. The meeting was organized in a manner that stimulated discussion among the 58 participants and focused on developments in polarized target technology and the underlying atomic physics. An impressive array of future possibilities for polarized targets as well as current developments in polarized target technology were discussed at the workshop. Abstracts of individual items from the workshop were prepared separately for the data base.

  2. The Dynamics of Digital Platform Innovation

    DEFF Research Database (Denmark)

    Eaton, Ben

    2016-01-01

    Curated platforms provide an architectural basis for third parties to develop platform complements and for platform owners to control their implementation as a form of open innovation. The refusal to implement complements as innovations can cause tension between platform owners and developers. Th...... digital platforms. In doing so, it uses IS notions of digitalization to challenge traditional understandings of innovation in platform architectures....

  3. Political Competition and Polarization

    DEFF Research Database (Denmark)

    Schultz, Christian

    This paper considers political competition and the consequences of political polarization when parties are better informed about how the economy functions than voters are. Specifically, parties know the cost producing a public good, voters do not. An incumbent's choice of policy acts like a signa...... for costs before an upcoming election. It is shown that the more polarized the political parties the more distorted the incumbent's policy choice.......This paper considers political competition and the consequences of political polarization when parties are better informed about how the economy functions than voters are. Specifically, parties know the cost producing a public good, voters do not. An incumbent's choice of policy acts like a signal...

  4. Physics of polarized targets

    CERN Document Server

    Niinikoski, Tapio

    2014-01-01

    For developing, building and operating solid polarized targets we need to understand several fields of physics that have seen sub stantial advances during the last 50 years. W e shall briefly review a selection of those that are important today. These are: 1) quantum statistical methods to describe saturation and relaxation in magnetic resonance; 2) equal spin temperature model for dy namic nuclear polarization; 3 ) weak saturation during NMR polarization measurement; 4 ) refrigeration using the quantum fluid properties of helium isotopes. These, combined with superconducting magnet technologies, permit today to reach nearly complete pola rization of almost any nuclear spins. Targets can be operated in frozen spin mode in rather low and inhomogeneous field of any orientation, and in DNP mode in beams of high intensity. Beyond such experiments of nuclear and particle physics, applications a re also emerging in macromolecular chemistry and in magnetic resonance imaging. This talk is a tribute to Michel Borghini...

  5. No More Polarization, Please!

    DEFF Research Database (Denmark)

    Hansen, Mia Reinholt

    The organizational science literature on motivation has for long been polarized into two main positions; the organizational economic position focusing on extrinsic motivation and the organizational behavior position emphasizing intrinsic motivation. With the rise of the knowledge economy...... and the increasing levels of complexities it entails, such polarization is not fruitful in the attempt to explain motivation of organizational members. This paper claims that a more nuanced perspective on motivation, acknowledging the co-existence of intrinsic and extrinsic motivation, the possible interaction...... between the two as well as different types of motivations filling in the gap between the two polar types, is urgently needed in the organizational science literature. By drawing on the research on intrinsic and extrinsic motivation conducted in social psychology and combining this with contributions from...

  6. Polarized source upgrading

    International Nuclear Information System (INIS)

    Clegg, T.B.; Rummel, R.L.; Carter, E.P.; Westerfeldt, C.R.; Lovette, A.W.; Edwards, S.E.

    1985-01-01

    The decision was made this past year to move the Lamb-shift polarized ion source which was first installed in the laboratory in 1970. The motivation was the need to improve the flexibility of spin-axis orientation by installing the ion source with a new Wien-filter spin precessor which is capable of rotating physically about the beam axis. The move of the polarized source was accomplished in approximately two months, with the accelerator being turned off for experiments during approximately four weeks of this time. The occasion of the move provided the opportunity to rewire completely the entire polarized ion source frame and to rebuild approximately half of the electronic chassis on the source. The result is an ion source which is now logically wired and carefully documented. Beams obtained from the source are much more stable than those previously available

  7. A lunar polar expedition

    Science.gov (United States)

    Dowling, Richard; Staehle, Robert L.; Svitek, Tomas

    1992-09-01

    Advanced exploration and development in harsh environments require mastery of basic human survival skill. Expeditions into the lethal climates of Earth's polar regions offer useful lessons for tommorrow's lunar pioneers. In Arctic and Antarctic exploration, 'wintering over' was a crucial milestone. The ability to establish a supply base and survive months of polar cold and darkness made extensive travel and exploration possible. Because of the possibility of near-constant solar illumination, the lunar polar regions, unlike Earth's may offer the most hospitable site for habitation. The World Space Foundation is examining a scenario for establishing a five-person expeditionary team on the lunar north pole for one year. This paper is a status report on a point design addressing site selection, transportation, power, and life support requirements.

  8. Numeric computation and statistical data analysis on the Java platform

    CERN Document Server

    Chekanov, Sergei V

    2016-01-01

    Numerical computation, knowledge discovery and statistical data analysis integrated with powerful 2D and 3D graphics for visualization are the key topics of this book. The Python code examples powered by the Java platform can easily be transformed to other programming languages, such as Java, Groovy, Ruby and BeanShell. This book equips the reader with a computational platform which, unlike other statistical programs, is not limited by a single programming language. The author focuses on practical programming aspects and covers a broad range of topics, from basic introduction to the Python language on the Java platform (Jython), to descriptive statistics, symbolic calculations, neural networks, non-linear regression analysis and many other data-mining topics. He discusses how to find regularities in real-world data, how to classify data, and how to process data for knowledge discoveries. The code snippets are so short that they easily fit into single pages. Numeric Computation and Statistical Data Analysis ...

  9. Adoption of Mobile Payment Platforms

    DEFF Research Database (Denmark)

    Staykova, Kalina Stefanova; Damsgaard, Jan

    2016-01-01

    Numerous mobile payment solutions, which rely on new disruptive technologies, have been launched on the payment market in recent years. But despite the growing number of mobile payment apps, very few solutions have turned to be successful as the majority of them fail to gain a critical mass...... of users. In this paper, we investigate successful platform adoption strategies by using the Reach and Range Framework for Multi-Sided Platforms as a strategic tool to which mobile payment providers can adhere in order to tackle some of the main challenges they face throughout the evolution...... of their platforms. The analysis indicates that successful mobile payment solutions tend to be launched as one-sided platforms and then gradually be expanded into being two-sided. Our study showcases that the success of mobile payment platforms lies with the ability of the platform to balance the reach (number...

  10. Helically labile bis(haloBODIPYs): an advantageous platform for the development of CPL-SOMs

    OpenAIRE

    Ray, C��sar; S��nchez-Carnerero, Esther M.; Moreno, Florencio; Maroto, Beatriz L.; Agarrabeitia, Antonia R.; Ortiz, Mar��a J.; L��pez-Arbeloa, ����igo; Ba��uelos, Jorge; Cohovi, Komlan D.; Lunkley, Jamie L.; Muller, Gilles; de la Moya, Santiago

    2016-01-01

    Simple organic molecules (SOM) based on bis(haloBODIPY) are shown to enable circularly polarized luminescence (CPL), giving rise to a new structural design for technologically valuable CPL-SOMs. The established design comprises together synthetic accessibility, labile helicity, possibility of reversing the handedness of the circularly polarized emission, and reactive functional groups, making it unique and attractive as advantageous platform for the development of smart CPL-SOMs.

  11. POLARIZED NEUTRONS IN RHIC

    Energy Technology Data Exchange (ETDEWEB)

    COURANT,E.D.

    1998-04-27

    There does not appear to be any obvious way to accelerate neutrons, polarized or otherwise, to high energies by themselves. To investigate the behavior of polarized neutrons the authors therefore have to obtain them by accelerating them as components of heavier nuclei, and then sorting out the contribution of the neutrons in the analysis of the reactions produced by the heavy ion beams. The best neutron carriers for this purpose are probably {sup 3}He nuclei and deuterons. A polarized deuteron is primarily a combination of a proton and a neutron with their spins pointing in the same direction; in the {sup 3}He nucleus the spins of the two protons are opposite and the net spin (and magnetic moment) is almost the same as that of a free neutron. Polarized ions other than protons may be accelerated, stored and collided in a ring such as RHIC provided the techniques proposed for polarized proton operation can be adapted (or replaced by other strategies) for these ions. To accelerate polarized particles in a ring, one must make provisions for overcoming the depolarizing resonances that occur at certain energies. These resonances arise when the spin tune (ratio of spin precession frequency to orbit frequency) resonates with a component present in the horizontal field. The horizontal field oscillates with the vertical motion of the particles (due to vertical focusing); its frequency spectrum is dominated by the vertical oscillation frequency and its modulation by the periodic structure of the accelerator ring. In addition, the magnet imperfections that distort the closed orbit vertically contain all integral Fourier harmonics of the orbit frequency.

  12. Energy Tracking Software Platform

    Energy Technology Data Exchange (ETDEWEB)

    Ryan Davis; Nathan Bird; Rebecca Birx; Hal Knowles

    2011-04-04

    Acceleration has created an interactive energy tracking and visualization platform that supports decreasing electric, water, and gas usage. Homeowners have access to tools that allow them to gauge their use and track progress toward a smaller energy footprint. Real estate agents have access to consumption data, allowing for sharing a comparison with potential home buyers. Home builders have the opportunity to compare their neighborhood's energy efficiency with competitors. Home energy raters have a tool for gauging the progress of their clients after efficiency changes. And, social groups are able to help encourage members to reduce their energy bills and help their environment. EnergyIT.com is the business umbrella for all energy tracking solutions and is designed to provide information about our energy tracking software and promote sales. CompareAndConserve.com (Gainesville-Green.com) helps homeowners conserve energy through education and competition. ToolsForTenants.com helps renters factor energy usage into their housing decisions.

  13. Web Platform Application

    Energy Technology Data Exchange (ETDEWEB)

    Paulsworth, Ashley [Sunvestment Group, Frederick, MD (United States); Kurtz, Jim [Sunvestment Group, Frederick, MD (United States); Brun de Pontet, Stephanie [Sunvestment Group, Frederick, MD (United States)

    2016-06-15

    Sunvestment Energy Group (previously called Sunvestment Group) was established to create a web application that brings together site hosts, those who will obtain the energy from the solar array, with project developers and funders, including affinity investors. Sunvestment Energy Group (SEG) uses a community-based model that engages with investors who have some affinity with the site host organization. In addition to a financial return, these investors receive non-financial value from their investments and are therefore willing to offer lower cost capital. This enables the site host to enjoy more savings from solar through these less expensive Community Power Purchase Agreements (CPPAs). The purpose of this award was to develop an online platform to bring site hosts and investors together virtually.

  14. Upgrading the AGS polarized beam facility

    International Nuclear Information System (INIS)

    Ratner, L.G.

    1991-01-01

    Although present techniques for crossing depolarizing resonances in circular accelerators work, they are very time-consuming to implement and were only able to provide about a 40% polarized beam at 22 GeV in the Alternating Gradient Synchrotron (AGS). We propose to install a partial ''Siberian Snake'' solenoid in the AGS to eliminate the need to correct imperfection resonances and to make other modifications in our intrinsic resonance correctors. This will allow us to reach an energy of 25 GeV with 70% polarization and will enable the AGS to be an efficient injector of polarized protons into the Relativistic Heavy Ion Collider (RHIC), as well as being able to carry on a fixed-target program with minimum set-up time. 3 refs., 5 figs., 1 tab

  15. Dark Polar Dunes

    Science.gov (United States)

    2005-01-01

    20 January 2004 This Mars Global Surveyor (MGS) Mars Orbiter Camera (MOC) image, acquired during northern summer in December 2004, shows dark, windblown sand dunes in the north polar region of Mars. A vast sea of sand dunes nearly surrounds the north polar cap. These landforms are located near 80.3oN, 144.1oW. Light-toned features in the image are exposures of the substrate that underlies the dune field. The image covers an area about 3 km (1.9 mi) wide and is illuminated by sunlight from the lower left.

  16. Imaging with Polarized Neutrons

    Directory of Open Access Journals (Sweden)

    Nikolay Kardjilov

    2018-01-01

    Full Text Available Owing to their zero charge, neutrons are able to pass through thick layers of matter (typically several centimeters while being sensitive to magnetic fields due to their intrinsic magnetic moment. Therefore, in addition to the conventional attenuation contrast image, the magnetic field inside and around a sample can be visualized by detecting changes of polarization in a transmitted beam. The method is based on the spatially resolved measurement of the cumulative precession angles of a collimated, polarized, monochromatic neutron beam that traverses a magnetic field or sample.

  17. The polar mesosphere

    International Nuclear Information System (INIS)

    Morris, Ray; Murphy, Damian

    2008-01-01

    The mesosphere region, which lies at the edge of space, contains the coldest layer of the Earth's atmosphere, with summer temperatures as low as minus 130 °C. In this extreme environment ice aerosol layers have appeared since the dawn of industrialization—whose existence may arguably be linked to human influence—on yet another layer of the Earth's fragile atmosphere. Ground-based and space-based experiments conducted in the Arctic and Antarctic during the International Polar Year (IPY) aim to address limitations in our knowledge and to advance our understanding of thermal and dynamical processes at play in the polar mesosphere

  18. Internal polarized targets

    Energy Technology Data Exchange (ETDEWEB)

    Kinney, E.R.; Coulter, K.; Gilman, R.; Holt, R.J.; Kowalczyk, R.S.; Napolitano, J.; Potterveld, D.H.; Young, L. (Argonne National Lab., IL (USA)); Mishnev, S.I.; Nikolenko, D.M.; Popov, S.G.; Rachek, I.A.; Temnykh, A.B.; Toporkov, D.K.; Tsentalovich, E.P.; Wojtsekhowski, B.B. (AN SSSR, Novosibirsk (USSR). Inst. Yadernoj Fiziki)

    1989-01-01

    Internal polarized targets offer a number of advantages over external targets. After a brief review of the basic motivation and principles behind internal polarized targets, the technical aspects of the atomic storage cell will be discussed in particular. Sources of depolarization and the means by which their effects can be ameliorated will be described, especially depolarization by the intense magnetic fields arising from the circulating particle beam. The experience of the Argonne Novosibirsk collaboration with the use of a storage cell in a 2 GeV electron storage ring will be the focus of this technical discussion. 17 refs., 11 figs.

  19. Product Platform Screening at LEGO

    DEFF Research Database (Denmark)

    Mortensen, Niels Henrik; Steen Jensen, Thomas; Nielsen, Ole Fiil

    2012-01-01

    Product platforms offer great benefits to companies developing new products in highly competitive markets. Literature describes how a single platform can be designed from a technical point of view, but rarely mentions how the process begins. How do companies identify possible platform candidates......, and how do they assess if these candidates have enough potential to be worth implementing? Danish toy manufacturer LEGO has systematically gone through this process twice. The first time the results were poor; almost all platform candidates failed. The second time, though, has been largely successful...

  20. Users and Programmers Guide for HPC Platforms in CIEMAT

    International Nuclear Information System (INIS)

    Munoz Roldan, A.

    2003-01-01

    This Technical Report presents a description of the High Performance Computing platforms available to researchers in CIEMAT and dedicated mainly to scientific computing. It targets to users and programmers and tries to help in the processes of developing new code and porting code across platforms. A brief review is also presented about historical evolution in the field of HPC, ie, the programming paradigms and underlying architectures. (Author) 32 refs

  1. The physics of polarization

    Science.gov (United States)

    Landi Degl'Innocenti, Egidio

    This course is intended to give a description of the basic physical concepts which underlie the study and the interpretation of polarization phenomena. Apart from a brief historical introduction (Sect. 1), the course is organized in three parts. A first part (Sects. 2 - 6) covers the most relevant facts about the polarization phenomena that are typically encountered in laboratory applications and in everyday life. In Sect. 2, the modern description of polarization in terms of the Stokes parameters is recalled, whereas Sect. 3 is devoted to introduce the basic tools of laboratory polarimetry, such as the Jones calculus and the Mueller matrices. The polarization phenomena which are met in the reflection and refraction of a beam of radiation at the separation surface between two dielectrics, or between a dielectric and a metal, are recalled in Sect. 4. Finally, Sect. 5 gives an introduction to the phenomena of dichroism and of anomalous dispersion and Sect. 6 summarizes the polarization phenomena that are commonly encountered in everyday life. The second part of this course (Sects. 7-14) deals with the description, within the formalism of classical physics, of the spectro-polarimetric properties of the radiation emitted by accelerated charges. Such properties are derived by taking as starting point the Liénard and Wiechert equations that are recalled and discussed in Sect. 7 both in the general case and in the non-relativistic approximation. The results are developed to find the percentage polarization, the radiation diagram, the cross-section and the spectral characteristics of the radiation emitted in different phenomena particularly relevant from the astrophysical point of view. The emission of a linear antenna is derived in Sect. 8. The other Sections are devoted to Thomson scattering (Sect. 9), Rayleigh scattering (Sect. 10), Mie scattering (Sect. 11), bremsstrahlung radiation (Sect. 12), cyclotron radiation (Sect. 13), and synchrotron radiation (Sect. 14

  2. Platform Machining Evaluation

    Science.gov (United States)

    2006-09-21

    Technology Division (MST) Redstone Arsenal, Alabama Scott A. Hofacker, PE – Program Manager 256.842.7992 scott.hofacker@us.army.mil or Mike Cummings ( Tiburon ) 256.313.6496 mike.a.cummings@us.army.mil

  3. Introducing Platform Interactions Model for Studying Multi-Sided Platforms

    DEFF Research Database (Denmark)

    Staykova, Kalina; Damsgaard, Jan

    2018-01-01

    Multi-Sided Platforms (MSPs) function as socio-technical entities that facilitate direct interactions between various affiliated to them constituencies through developing and managing IT architecture. In this paper, we aim to explain the nature of the platform interactions as key characteristic o...

  4. Characterizing the 3-D atmosphere with NUCAPS sounding products from multiple platforms

    Science.gov (United States)

    Barnet, C. D.; Smith, N.; Gambacorta, A.; Wheeler, A. A.; Sjoberg, W.; Goldberg, M.

    2017-12-01

    The JPSS Proving Ground and Risk Reduction (PGRR) Program launched the Sounding Initiative in 2014 to develop operational applications that use 3-D satellite soundings. These are near global daily swaths of vertical atmospheric profiles of temperature, moisture and trace gas species. When high vertical resolution satellite soundings first became available, their assimilation into user applications was slow: forecasters familiar with 2-D satellite imagery or 1-D radiosondes did not have the technical capability nor product knowledge to readily ingest satellite soundings. Similarly, the satellite sounding developer community lacked wherewithal to understand the many challenges forecasters face in their real time decision-making. It took the PGRR Sounding Initiative to bring these two communities together and develop novel applications that now depend on NUCAPS soundings. NUCAPS - the NOAA Unique Combined Atmospheric Processing System - is platform agnostic and generates satellite soundings from measurements made by infrared and microwave sounder pairs on the MetOp (IASI/AMSU) and Suomi NPP (CrIS/ATMS) polar-orbiting platforms. We highlight here three new applications developed under the PGRR Sounding Initiative. They are, (i) aviation: NUCAPS identifies cold air "blobs" that causes jet fuel to freeze, (ii) severe weather: NUCAPS identifies areas of convective initiation, and (iii) air quality: NUCAPS identifies stratospheric intrusions and tracks long-range transport of biomass burning plumes. The value of NUCAPS being platform agnostic will become apparent with the JPSS-1 launch. NUCAPS soundings from Suomi NPP and JPSS-1, being 50 min apart, could capture fast-changing weather events and together with NUCAPS soundings from the two MetOp platforms ( 4 hours earlier in the day than JPSS) could characterize diurnal cycles. In this paper, we will summarize key accomplishments and assess whether NUCAPS maintains enough continuity in its sounding products from multiple

  5. Venus Atmospheric Maneuverable Platform (VAMP)

    Science.gov (United States)

    Griffin, K.; Sokol, D.; Lee, G.; Dailey, D.; Polidan, R.

    2013-12-01

    We have explored a possible new approach to Venus upper atmosphere exploration by applying recent Northrop Grumman (non-NASA) development programs to the challenges associated with Venus upper atmosphere science missions. Our concept is a low ballistic coefficient (gas, wing span, vehicle mass, power supply, propulsion, materials considerations, structural elements, subsystems, and packaging. The interaction between the VAMP vehicle and the supporting orbiter will also be discussed. In this context, we will specifically focus upon four key factors impacting the design and performance of VAMP: 1. Feasibility of and options for the deployment of the vehicle in space 2. Entry into the Venus atmosphere, including descent profile, heat rate, total heat load, stagnation temperature, control, and entry into level flight 3. Characteristics of flight operations and performance in the Venus atmosphere: altitude range, latitude and longitude access, day/night performance, aircraft performance (aerodynamics, power required vs. power available, propulsion, speed, percent buoyancy), performance sensitivity to payload weight 4. Science payload accommodation, constraints, and opportunities We will discuss interdependencies of the above factors and the manner in which the VAMP strawman's characteristics affect the CONOPs and the science objectives. We will show how the these factors provide constraints as well as enable opportunities for novel long duration scientific studies of the Venus upper atmosphere that support VEXAG goals 2 and 3. We will also discuss how the VAMP platform itself can facilitate some of these science measurements.

  6. Basin Assessment Spatial Planning Platform

    Energy Technology Data Exchange (ETDEWEB)

    2017-07-26

    The tool is intended to facilitate hydropower development and water resource planning by improving synthesis and interpretation of disparate spatial datasets that are considered in development actions (e.g., hydrological characteristics, environmentally and culturally sensitive areas, existing or proposed water power resources, climate-informed forecasts). The tool enables this capability by providing a unique framework for assimilating, relating, summarizing, and visualizing disparate spatial data through the use of spatial aggregation techniques, relational geodatabase platforms, and an interactive web-based Geographic Information Systems (GIS). Data are aggregated and related based on shared intersections with a common spatial unit; in this case, industry-standard hydrologic drainage areas for the U.S. (National Hydrography Dataset) are used as the spatial unit to associate planning data. This process is performed using all available scalar delineations of drainage areas (i.e., region, sub-region, basin, sub-basin, watershed, sub-watershed, catchment) to create spatially hierarchical relationships among planning data and drainages. These entity-relationships are stored in a relational geodatabase that provides back-end structure to the web GIS and its widgets. The full technology stack was built using all open-source software in modern programming languages. Interactive widgets that function within the viewport are also compatible with all modern browsers.

  7. PolarTREC-Teachers and Researchers Exploring and Collaborating: Bringing Polar Research to the Classroom

    Science.gov (United States)

    Warnick, W. K.; Warburton, J.; Breen, K.; Wiggins, H. V.; Larson, A.; Behr, S.

    2006-12-01

    PolarTREC-Teachers and Researchers Exploring and Collaborating is a three-year (2007-2009) teacher professional development program that pairs K-12 teachers with researchers to improve science education through authentic polar research experience. PolarTREC builds on the strengths of the existing TREC program in the Arctic, an NSF supported program managed by the Arctic Research Consortium of the US (ARCUS), to embrace a wider range of research activities in the Arctic and Antarctic. PolarTREC uses a Teacher Research Experience (TRE) model to foster the integration of research and education to produce a legacy of long-term teacher-researcher collaborations, improved teacher content knowledge through experiences in scientific inquiry, and broad public interest and engagement in polar science. PolarTREC will enable thirty-six teachers to spend two to six weeks in the Arctic or Antarctic, working closely with researchers investigating a wide range of topics such as sea-ice dynamics, terrestrial ecology, marine biology, atmospheric chemistry, and long-term climate change. With the help of their host researcher and the research team, teachers will develop the experience and tools necessary to teach science through scientific inquiry and investigation based on real-world experiences. While in the field, teachers and researchers will communicate extensively with their colleagues, communities, and hundreds of students of all ages across the globe, using a variety of tools including satellite phones, online journals, podcasts and interactive "Live from IPY" calls and web-based seminars. The online outreach elements of the project convey these experiences to a broad audience far beyond the classrooms of the PolarTREC teachers. In addition to field research experiences, PolarTREC will support teacher professional development and a sustained community of teachers, scientists, and the public through workshops, Internet seminars, an e-mail listserve, and ongoing teacher

  8. Lobbying and political polarization

    OpenAIRE

    Ursprung, Heinrich W.

    2002-01-01

    Standard spatial models of political competition give rise to equilibria in which the competing political parties or candidates converge to a common position. In this paper I show how political polarization can be generated in models that focus on the nexus between pre-election interest group lobbying and electoral competition.

  9. Fluorescence confocal polarizing microscopy

    Indian Academy of Sciences (India)

    Much of the modern understanding of orientational order in liquid crystals (LCs) is based on polarizing microscopy (PM). A PM image bears only two-dimensional (2D) information, integrating the 3D pattern of optical birefringence over the path of light. Recently, we proposed a technique to image 3D director patterns by ...

  10. Polarization of Bremsstrahlung

    International Nuclear Information System (INIS)

    Miller, J.

    1957-01-01

    The numerical results for the polarization of Bremsstrahlung are presented. The multiple scattering of electrons in the target is taken into account. The angular-and photon energy dependences are seen on the curves for an incident 25 MeV electron energy. (Author) [fr

  11. DESY: HERA polarization

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    The new HERA electron-proton collider at DESY in Hamburg achieved the first luminosity for electron-proton collisions on 19 October last year. Only one month later, on 20 November, HERA passed another important milestone with the observation of transverse electron polarization

  12. Titan Polar Landscape Evolution

    Science.gov (United States)

    Moore, Jeffrey M.

    2016-01-01

    With the ongoing Cassini-era observations and studies of Titan it is clear that the intensity and distribution of surface processes (particularly fluvial erosion by methane and Aeolian transport) has changed through time. Currently however, alternate hypotheses substantially differ among specific scenarios with respect to the effects of atmospheric evolution, seasonal changes, and endogenic processes. We have studied the evolution of Titan's polar region through a combination of analysis of imaging, elevation data, and geomorphic mapping, spatially explicit simulations of landform evolution, and quantitative comparison of the simulated landscapes with corresponding Titan morphology. We have quantitatively evaluated alternate scenarios for the landform evolution of Titan's polar terrain. The investigations have been guided by recent geomorphic mapping and topographic characterization of the polar regions that are used to frame hypotheses of process interactions, which have been evaluated using simulation modeling. Topographic information about Titan's polar region is be based on SAR-Topography and altimetry archived on PDS, SAR-based stereo radar-grammetry, radar-sounding lake depth measurements, and superposition relationships between geomorphologic map units, which we will use to create a generalized topographic map.

  13. REVEAL: Software Documentation and Platform Migration

    Science.gov (United States)

    Wilson, Michael A.; Veibell, Victoir T.; Freudinger, Lawrence C.

    2008-01-01

    The Research Environment for Vehicle Embedded Analysis on Linux (REVEAL) is reconfigurable data acquisition software designed for network-distributed test and measurement applications. In development since 2001, it has been successfully demonstrated in support of a number of actual missions within NASA s Suborbital Science Program. Improvements to software configuration control were needed to properly support both an ongoing transition to operational status and continued evolution of REVEAL capabilities. For this reason the project described in this report targets REVEAL software source documentation and deployment of the software on a small set of hardware platforms different from what is currently used in the baseline system implementation. This report specifically describes the actions taken over a ten week period by two undergraduate student interns and serves as a final report for that internship. The topics discussed include: the documentation of REVEAL source code; the migration of REVEAL to other platforms; and an end-to-end field test that successfully validates the efforts.

  14. Characteristics of volume polarization holography with linear polarization light

    Science.gov (United States)

    Zang, Jinliang; Wu, An'an; Liu, Ying; Wang, Jue; Lin, Xiao; Tan, Xiaodi; Shimura, Tsutomu; Kuroda, Kazuo

    2015-10-01

    Volume polarization holographic recording in phenanthrenequinone-doped poly(methyl methacrylate) (PQ-PMMA) photopolymer with linear polarized light is obtained. The characteristics of the volume polarization hologram are experimentally investigated. It is found that beyond the paraxial approximation the polarization states of the holographic reconstruction light are generally different from the signal light. Based on vector wave theoretical analyses and material properties, the special exposure condition for correctly holographic reconstruction is obtained and experimentally demonstrated.

  15. Rapid prototyping of robotic platforms

    CSIR Research Space (South Africa)

    De Ronde, Willis

    2016-11-01

    Full Text Available Building a robotic platform from raw materials can take anything from a few weeks to a few years to complete, depending on the complexity and size of the platform. This paper aims to introduce a novel approach of using abrasive waterjet machining...

  16. A practice scaffolding interactive platform

    DEFF Research Database (Denmark)

    Bundsgaard, Jeppe

    2009-01-01

    A Practice Scaffolding Interactive Platform (PracSIP) is a social learning platform which supports students in collaborative project based learning by simulating a professional practice. A PracSIP puts the core tools of the simulated practice at the students' disposal, it organizes collaboration...

  17. Preparing for a Product Platform

    DEFF Research Database (Denmark)

    Fiil-Nielsen, Ole; Munk, Lone; Mortensen, Niels Henrik

    2005-01-01

    they lead to increased sales due to more customized product as well as decreased costs due to reuse, making a product development platform a very profitable strategy for product developing companies. A successful implementation of a product development platform is not straightforward though...

  18. Experiments with Fermilab polarized proton and polarized antiproton beams

    International Nuclear Information System (INIS)

    Yokosawa, A.

    1990-01-01

    We summarize activities concerning the Fermilab polarized beams. They include a brief description of the polarized-beam facility, measurements of beam polarization by polarimeters, asymmetry measurements in the π degree production at high p perpendicular and in the Λ (Σ degree), π ± , π degree production at large x F , and Δσ L (pp, bar pp) measurements. 18 refs

  19. NUCLEON POLARIZATION IN 3-BODY MODELS OF POLARIZED LI-6

    NARCIS (Netherlands)

    SCHELLINGERHOUT, NW; KOK, LP; COON, SA; ADAM, RM

    1993-01-01

    Just as He-3 --> can be approximately characterized as a polarized neutron target, polarized Li-6D has been advocated as a good isoscalar nuclear target for the extraction of the polarized gluon content of the nucleon. The original argument rests upon a presumed ''alpha + deuteron'' picture of Li-6,

  20. Paper based electronics platform

    KAUST Repository

    Nassar, Joanna Mohammad

    2017-07-20

    A flexible and non-functionalized low cost paper-based electronic system platform fabricated from common paper, such as paper based sensors, and methods of producing paper based sensors, and methods of sensing using the paper based sensors are provided. A method of producing a paper based sensor can include the steps of: a) providing a conventional paper product to serve as a substrate for the sensor or as an active material for the sensor or both, the paper product not further treated or functionalized; and b) applying a sensing element to the paper substrate, the sensing element selected from the group consisting of a conductive material, the conductive material providing contacts and interconnects, sensitive material film that exhibits sensitivity to pH levels, a compressible and/or porous material disposed between a pair of opposed conductive elements, or a combination of two of more said sensing elements. The method of sensing can further include measuring, using the sensing element, a change in resistance, a change in voltage, a change in current, a change in capacitance, or a combination of any two or more thereof.

  1. Geomagnetic polarity transitions

    Science.gov (United States)

    Merrill, Ronald T.; McFadden, Phillip L.

    1999-05-01

    The top of Earth's liquid outer core is nearly 2900 km beneath Earth's surface, so we will never be able to observe it directly. This hot, dense, molten iron-rich body is continuously in motion and is the source of Earth's magnetic field. One of the most dynamic manifestations at Earth's surface of this fluid body is, perhaps, a reversal of the geomagnetic field. Unfortunately, the most recent polarity transition occurred at about 780 ka, so we have never observed a transition directly. It seems that a polarity transition spans many human lifetimes, so no human will ever witness the phenomenon in its entirety. Thus we are left with the tantalizing prospect that paleomagnetic records of polarity transitions may betray some of the secrets of the deep Earth. Certainly, if there are systematics in the reversal process and they can be documented, then this will reveal substantial information about the nature of the lowermost mantle and of the outer core. Despite their slowness on a human timescale, polarity transitions occur almost instantaneously on a geological timescale. This rapidity, together with limitations in the paleomagnetic recording process, prohibits a comprehensive description of any reversal transition both now and into the foreseeable future, which limits the questions that may at this stage be sensibly asked. The natural model for the geomagnetic field is a set of spherical harmonic components, and we are not able to obtain a reliable model for even the first few harmonic terms during a transition. Nevertheless, it is possible, in principle, to make statements about the harmonic character of a geomagnetic polarity transition without having a rigorous spherical harmonic description of one. For example, harmonic descriptions of recent geomagnetic polarity transitions that are purely zonal can be ruled out (a zonal harmonic does not change along a line of latitude). Gleaning information about transitions has proven to be difficult, but it does seem

  2. Building AN International Polar Data Coordination Network

    Science.gov (United States)

    Pulsifer, P. L.; Yarmey, L.; Manley, W. F.; Gaylord, A. G.; Tweedie, C. E.

    2013-12-01

    In the spirit of the World Data Center system developed to manage data resulting from the International Geophysical Year of 1957-58, the International Polar Year 2007-2009 (IPY) resulted in significant progress towards establishing an international polar data management network. However, a sustained international network is still evolving. In this paper we argue that the fundamental building blocks for such a network exist and that the time is right to move forward. We focus on the Arctic component of such a network with linkages to Antarctic network building activities. A review of an important set of Network building blocks is presented: i) the legacy of the IPY data and information service; ii) global data management services with a polar component (e.g. World Data System); iii) regional systems (e.g. Arctic Observing Viewer; iv) nationally focused programs (e.g. Arctic Observing Viewer, Advanced Cooperative Arctic Data and Information Service, Polar Data Catalogue, Inuit Knowledge Centre); v) programs focused on the local (e.g. Exchange for Local Observations and Knowledge of the Arctic, Geomatics and Cartographic Research Centre). We discuss current activities and results with respect to three priority areas needed to establish a strong and effective Network. First, a summary of network building activities reports on a series of productive meetings, including the Arctic Observing Summit and the Polar Data Forum, that have resulted in a core set of Network nodes and participants and a refined vision for the Network. Second, we recognize that interoperability for information sharing fundamentally relies on the creation and adoption of community-based data description standards and data delivery mechanisms. There is a broad range of interoperability frameworks and specifications available; however, these need to be adapted for polar community needs. Progress towards Network interoperability is reviewed, and a prototype distributed data systems is demonstrated. We

  3. Polarized electron beams at SLAC

    International Nuclear Information System (INIS)

    Moffeit, K.C.

    1992-11-01

    SLAC has successfully accelerated high energy polarized electrons for the Stanford Linear Collider and fixed polarized nuclear target experiments. The polarized electron beams at SLAC use a gallium arsenide (GaAlAs for E-142) photon emission source to provide the beam of polarized electrons with polarization of approximately 28% (41% for E-142). While the beam emittance is reduced in the damping ring for SLC operation a system of bend magnets and superconducting solenoids preserve and orient the spin direction for maximum longitudinal polarization at the collision point. The electron polarization is monitored with a Compton scattering polarimeter, and was typically 22% at the e+e- collision point for the 1992 run. Improvements are discussed to increase the source polarization and to reduce the depolarization effects between the source and the collision point

  4. Nuclear platform research and development - 2008-09 highlights

    International Nuclear Information System (INIS)

    Sadhankar, R.R.

    2009-08-01

    The Nuclear Platform R and D Program has lead responsibility for the maintenance and further development of the CANDU intellectual property covering the safety, licensing and design basis for nuclear facilities. The Nuclear Platform R and D Program is part of the Research and Technology Operation (RTO) unit of AECL and is managed through the Research and Development division, which has responsibility for maintaining and enhancing the knowledge and technology base. The RTO is also responsible for managing AECL's nuclear facilities and infrastructure (including laboratories and R and D facilities), the nuclear waste management program and other legacy liabilities (e.g., decommissioning) to demonstrate and grow shareholder value. The Nuclear Platform also provides the technology base from which new products and services can be developed to meet customer needs (including ACR and commercial products and services). (author)

  5. Towards Enabling Overture as a Platform for Formal Notation IDEs

    Directory of Open Access Journals (Sweden)

    Luís Diogo Couto

    2015-08-01

    Full Text Available Formal Methods tools will never have as many users as tools for popular programming languages and so the effort spent on constructing Integrated Development Environments (IDEs will be orders of magnitudes lower than that of programming languages such as Java. This means newcomers to formal methods do not get the same user experience as with their favourite programming IDE. In order to improve this situation it is essential that efforts are combined so it is possible to reuse common features and thus not start from scratch every time. This paper presents the Overture platform where such a reuse philosophy is present. We give an overview of the platform itself as well as the extensibility principles that enable much of the reuse. The paper also contains several examples platform extensions, both in the form of new features and a new IDE supporting a new language.

  6. Malaria Diagnosis Using a Mobile Phone Polarized Microscope

    Science.gov (United States)

    Pirnstill, Casey W.; Coté, Gerard L.

    2015-08-01

    Malaria remains a major global health burden, and new methods for low-cost, high-sensitivity, diagnosis are essential, particularly in remote areas with low-resource around the world. In this paper, a cost effective, optical cell-phone based transmission polarized light microscope system is presented for imaging the malaria pigment known as hemozoin. It can be difficult to determine the presence of the pigment from background and other artifacts, even for skilled microscopy technicians. The pigment is much easier to observe using polarized light microscopy. However, implementation of polarized light microscopy lacks widespread adoption because the existing commercial devices have complicated designs, require sophisticated maintenance, tend to be bulky, can be expensive, and would require re-training for existing microscopy technicians. To this end, a high fidelity and high optical resolution cell-phone based polarized light microscopy system is presented which is comparable to larger bench-top polarized microscopy systems but at much lower cost and complexity. The detection of malaria in fixed and stained blood smears is presented using both, a conventional polarized microscope and our cell-phone based system. The cell-phone based polarimetric microscopy design shows the potential to have both the resolution and specificity to detect malaria in a low-cost, easy-to-use, modular platform.

  7. Research about Memory Detection Based on the Embedded Platform

    Science.gov (United States)

    Sun, Hao; Chu, Jian

    As is known to us all, the resources of memory detection of the embedded systems are very limited. Taking the Linux-based embedded arm as platform, this article puts forward two efficient memory detection technologies according to the characteristics of the embedded software. Especially for the programs which need specific libraries, the article puts forwards portable memory detection methods to help program designers to reduce human errors,improve programming quality and therefore make better use of the valuable embedded memory resource.

  8. On Determinants of Political Polarization

    OpenAIRE

    Grechyna, Daryna

    2015-01-01

    Political polarization has been shown to significantly influence a country's economic performance. However, little is known about the drivers of political polarization. In this article, we aim to identify the main determinants of political polarization using Bayesian Model Averaging to overcome the problem of model uncertainty. We find that the level of trust within a country and the degree of income inequality are the most robust determinants of political polarization.

  9. Stratospheric Platforms for Monitoring Purposes

    International Nuclear Information System (INIS)

    Konigorski, D.; Gratzel, U.; Obersteiner, M.; Schneidereit, M.

    2010-01-01

    Stratospheric platforms are emerging systems based on challenging technology. Goal is to create a platform, payload, and mission design which is able to complement satellite services on a local scale. Applications are close to traditional satellite business in telecommunication, navigation, science, and earth observation and include for example mobile telecommunications, navigation augmentation, atmospheric research, or border control. Stratospheric platforms could potentially support monitoring activities related to safeguards, e.g. by imagery of surfaces, operational conditions of nuclear facilities, and search for undeclared nuclear activities. Stratospheric platforms are intended to be flown in an altitude band between 16 and 30 km, above 16-20 km to take advantage of usually lower winds facilitating station keeping, below 30 km to limit the challenges to achieve a reasonable payload at acceptable platform sizes. Stratospheric platforms could substitute satellites which are expensive and lack upgrade capabilities for new equipment. Furthermore they have practically an unlimited time over an area of interest. It is intended to keep the platforms operational and maintenance free on a 24/7 basis with an average deployment time of 3 years. Geostationary satellites lack resolution. Potential customers like Armed Forces, National Agencies and commercial customers have indicated interest in the use of stratospheric platforms. Governmental entities are looking for cheaper alternatives to communications and surveillance satellites and stratospheric platforms could offer the following potential advantages: Lower operational cost than satellite or UAV (Unmanned Aerial Vehicles) constellation (fleet required); Faster deployment than satellite constellation; Repositioning capability and ability to loiter as required; Persistent long-term real-time services over a fairly large regional spot; Surge capability: Able to extend capability (either monitoring or communications

  10. Temperature, salinity, dissolved oxygen measurements collected using CTD, bottle from multiple platforms in the Gulf of Mexico from 1992 through 2008 as part of the Southeast Area Monitoring and Assessment Program (SEAMAP) (NODC Accession 0069702)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Southeast Area Monitoring and Assessment Program (SEAMAP) is a State/Federal/university program for collection, management and dissemination of...

  11. Temperature, salinity, dissolved oxygen measurements collected using CTD, bottle from multiple platforms in the Gulf of Mexico from 2009 through 2015 as part of the Southeast Area Monitoring and Assessment Program (SEAMAP) (NCEI Accession 0131259)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Southeast Area Monitoring and Assessment Program (SEAMAP) is a State/Federal/university program for collection, management and dissemination of...

  12. Volume production of polarization controlled single-mode VCSELs

    Science.gov (United States)

    Grabherr, Martin; King, Roger; Jäger, Roland; Wiedenmann, Dieter; Gerlach, Philipp; Duckeck, Denise; Wimmer, Christian

    2008-02-01

    Over the past 3 years laser based tracking systems for optical PC mice have outnumbered the traditional VCSEL market datacom by far. Whereas VCSEL for datacom in the 850 nm regime emit in multipe transverse modes, all laser based tracking systems demand for single-mode operation which require advanced manufacturing technology. Next generation tracking systems even require single-polarization characteristics in order to avoid unwanted movement of the pointer due to polarization flips. High volume manufacturing and optimized production methods are crucial for achieving the addressed technical and commercial targets of this consumer market. The resulting ideal laser source which emits single-mode and single-polarization at low cost is also a promising platform for further applications like tuneable diode laser absorption spectroscopy (TDLAS) or miniature atomic clocks when adapted to the according wavelengths.

  13. Polarized electrogowdy spacetimes censored

    Energy Technology Data Exchange (ETDEWEB)

    Nungesser, Ernesto, E-mail: ernesto.nungesser@aei.mpg.d [Max-Planck-Institut fuer Gravitationsphysik, Albert-Einstein-Institut, Am Muehlenberg 1, 14476 Potsdam (Germany)

    2010-05-01

    A sketch of the proof of strong cosmic censorship is presented for a class of solutions of the Einstein-Maxwell equations, those with polarized Gowdy symmetry. A key element of the argument is the observation that by means of a suitable choice of variables the central equations in this problem can be written in a form where they are identical to the central equations for general (i.e. non-polarized) vacuum Gowdy spacetimes. Using this it is seen that the results of Ringstroem on strong cosmic censorship in the vacuum case have implications for the Einstein-Maxwell case. Working out the geometrical meaning of these analytical results leads to the main conclusion.

  14. Polarization induced doped transistor

    Science.gov (United States)

    Xing, Huili; Jena, Debdeep; Nomoto, Kazuki; Song, Bo; Zhu, Mingda; Hu, Zongyang

    2016-06-07

    A nitride-based field effect transistor (FET) comprises a compositionally graded and polarization induced doped p-layer underlying at least one gate contact and a compositionally graded and doped n-channel underlying a source contact. The n-channel is converted from the p-layer to the n-channel by ion implantation, a buffer underlies the doped p-layer and the n-channel, and a drain underlies the buffer.

  15. Polar bears, Ursus maritimus

    Science.gov (United States)

    Rode, Karyn D.; Stirling, Ian

    2017-01-01

    Polar bears are the largest of the eight species of bears found worldwide and are covered in a pigment-free fur giving them the appearance of being white. They are the most carnivorous of bear species consuming a high-fat diet, primarily of ice-associated seals and other marine mammals. They range throughout the circumpolar Arctic to the southernmost extent of seasonal pack ice.

  16. Polarized advanced fuel reactors

    International Nuclear Information System (INIS)

    Kulsrud, R.M.

    1987-07-01

    The d- 3 He reaction has the same spin dependence as the d-t reaction. It produces no neutrons, so that if the d-d reactivity could be reduced, it would lead to a neutron-lean reactor. The current understanding of the possible suppression of the d-d reactivity by spin polarization is discussed. The question as to whether a suppression is possible is still unresolved. Other advanced fuel reactions are briefly discussed. 11 refs

  17. On polarization in biomembranes

    DEFF Research Database (Denmark)

    Zecchi, Karis Amata

    close to physiological conditions, making these effects biologically relevant. In this work, we consider the case of asymmetric membranes which can display spontaneous polarization in the absence of a field. Close to the phase transition, we find that the membrane displays piezoelectric, flexoelectric...... on different geometries point in the direction of a flexoelectric mechanism behind current rectification in lipid bilayers. Finally, we suggest that our updated equivalent circuit should be included in the interpretation of elctrophysiological data....

  18. Multifrequency Behaviour of Polars

    Directory of Open Access Journals (Sweden)

    K. Reinsch

    2015-02-01

    Full Text Available Cataclysmic variables emit over a wide range of the electromagnetic spectrum. In this paper I will review observations of polars in relevant passbands obtained during the last decade and will discuss their diagnostical potential to access the physics of the main components within the binary systems. This will include a discussion of intrinsic source variability and the quest for simultaneous multi-frequency observations.

  19. Vertical Relationships within Platform Marketplaces

    Directory of Open Access Journals (Sweden)

    Mark J. Tremblay

    2016-07-01

    Full Text Available In two-sided markets a platform allows consumers and sellers to interact by creating sub-markets within the platform marketplace. For example, Amazon has sub-markets for all of the different product categories available on its site, and smartphones have sub-markets for different types of applications (gaming apps, weather apps, map apps, ridesharing apps, etc.. The network benefits between consumers and sellers depend on the mode of competition within the sub-markets: more competition between sellers lowers product prices, increases the surplus consumers receive from a sub-market, and makes platform membership more desirable for consumers. However, more competition also lowers profits for a seller which makes platform membership less desirable for a seller and reduces seller entry and the number of sub-markets available on the platform marketplace. This dynamic between seller competition within a sub-market and agents’ network benefits leads to platform pricing strategies, participation decisions by consumers and sellers, and welfare results that depend on the mode of competition. Thus, the sub-market structure is important when investigating platform marketplaces.

  20. The European Photovoltaic Technology Platform

    Energy Technology Data Exchange (ETDEWEB)

    Nowak, S. [NET Nowak Energy and Technology Ltd., Waldweg 8, CH-1717 St. Ursen (Switzerland); Aulich, H. [PV Silicon, Erfurt (Germany); Bal, J.L. [ADEME, Paris (France); Dimmler, B. [Wuerth Solar, Marbach am Neckar (Germany); Garnier, A. [Saint-Gobain Glass, Thourotte (France); Jongerden, G. [Akzo Nobel, Arnhem (Netherlands); Luther, J. [Fraunhofer ISE, Freiburg (Germany); Luque, A. [Universidad Politecnica de Madrid, Madrid (Spain); Milner, A. [Q-Cells, Thalheim (Germany); Nelson, D. [Foster and Partners, London (United Kingdom); Pataki, I. [Hungarian Energy Office, Budapest (Hungary); Pearsall, N. [Northumbria University, Newcastle upon Tyne (United Kingdom); Perezagua, E. [Isofoton, Madrid (Spain); Pietruszko, S. [Warsaw University of Technology, Warsaw (Poland); Rehak, J. [Solartec, Roznov pod Radhostem (Czech Republic); Schellekens, E. [European Association of electrical contractors, Kortenberg (Belgium); Shanker, A. [IED, Francheville (France); Silvestrini, G. [Kyoto Club, Rome (Italy); Sinke, W. [ECN Solar Energy, Petten (Netherlands); Willemsen, H. [Shell Solar, The Hague (Netherlands)

    2006-05-15

    The European Photovoltaic Technology Platform is one of the European Technology Platforms, a new instrument proposed by the European Commission. European Technology Platforms (ETPs) are a mechanism to bring together all interested stakeholders to develop a long-term vision to address a specific challenge, create a coherent, dynamic strategy to achieve that vision and steer the implementation of an action plan to deliver agreed programmes of activities and optimise the benefits for all parties. The European Photovoltaic Technology Platform has recently been established to define, support and accompany the implementation of a coherent and comprehensive strategic plan for photovoltaics. The platform will mobilise all stakeholders sharing a long-term European vision for PV, helping to ensure that Europe maintains and improves its industrial position. The platform will realise a European Strategic Research Agenda for PV for the next decade(s). Guided by a Steering Committee of 20 high level decision-makers representing all relevant European PV Stakeholders, the European PV Technology Platform comprises 4 Working Groups dealing with the subjects policy and instruments; market deployment; science, technology and applications as well as developing countries and is supported by a secretariat.

  1. The Polar Rock Repository: Rescuing Polar Collections for New Research

    Science.gov (United States)

    Grunow, A.

    2016-12-01

    Geological field expeditions in polar regions are logistically difficult, financially expensive and can have a significant environmental impact on pristine regions. The scarcity of outcrop in Antarctica (98% ice-covered) makes previously collected rock samples very valuable to the science community. NSF recognized the need for preserving rock, dredge, and terrestrial core samples from polar areas and created the Polar Rock Repository (PRR). The PRR collection allows for full and open access to both samples and metadata via the PRR website. In addition to the physical samples and their basic metadata, the PRR archives supporting materials from the collector, field notebooks, images of the samples, field maps, air photos, thin sections and any associated bibliography/DOI's. Many of these supporting materials are unique. More than 40,000 samples are available from the PRR for scientific analysis to researchers around the globe. Most of the samples cataloged at the PRR were collected more than 30 years ago, some more than 100 years ago. The rock samples and metadata are made available online through an advanced search engine for the PRR website. This allows scientists to "drill down" into search results using categories and look-up object fields similar to websites like Amazon. Results can be viewed in a table, downloaded as a spreadsheet, or plotted on an interactive map that supports display of satellite imagery and bathymetry layers. Samples can be requested by placing them in the `shopping cart'. These old sample collections have been repeatedly used by scientists from around the world. One data request involved locating coal deposits in Antarctica for a global compilation and another for looking at the redox state of batholithic rocks from the Antarctic Peninsula using magnetic susceptibilities of PRR rocks. Sample usage has also included non-traditional geologic studies, such as a search for monopoles in Cenozoic volcanic samples, and remote sensing

  2. Polar Business Design

    Directory of Open Access Journals (Sweden)

    Sébastien Caisse

    2014-02-01

    Full Text Available Polar business design aims to enable entrepreneurs, managers, consultants, researchers, and business students to better tackle model-based analysis, creation, and transformation of businesses, ventures, and, more generically, collective endeavors of any size and purpose. It is based on a systems-thinking approach that builds on a few interrelated core concepts to create holistic visual frameworks. These core concepts act as poles linked by meaningful dyads, flows, and faces arranged in geometric shapes. The article presents two such polar frameworks as key findings in an ongoing analytic autoethnography: the three-pole Value−Activity−Stakeholder (VAS triquetra and the four-pole Offer−Creation−Character−Stakeholder (OCCS tetrahedron. The VAS triquetra is a more aggregated model of collective endeavors. The OCCS tetrahedron makes a trade-off between a steeper learning curve and deeper, richer representation potential. This article discusses how to use these two frameworks as well as their limits, and explores the potential that polar business design offers for future research.

  3. An Intelligent Robot Programing

    Energy Technology Data Exchange (ETDEWEB)

    Hong, Seong Yong

    2012-01-15

    This book introduces an intelligent robot programing with background of the begging, introduction of VPL, and SPL, building of environment for robot platform, starting of robot programing, design of simulation environment, robot autonomy drive control programing, simulation graphic. Such as SPL graphic programing graphical image and graphical shapes, and graphical method application, application of procedure for robot control, robot multiprogramming, robot bumper sensor programing, robot LRF sencor programing and robot color sensor programing.

  4. An Intelligent Robot Programing

    International Nuclear Information System (INIS)

    Hong, Seong Yong

    2012-01-01

    This book introduces an intelligent robot programing with background of the begging, introduction of VPL, and SPL, building of environment for robot platform, starting of robot programing, design of simulation environment, robot autonomy drive control programing, simulation graphic. Such as SPL graphic programing graphical image and graphical shapes, and graphical method application, application of procedure for robot control, robot multiprogramming, robot bumper sensor programing, robot LRF sencor programing and robot color sensor programing.

  5. Wearable Device Control Platform Technology for Network Application Development

    Directory of Open Access Journals (Sweden)

    Heejung Kim

    2016-01-01

    Full Text Available Application development platform is the most important environment in IT industry. There are a variety of platforms. Although the native development enables application to optimize, various languages and software development kits need to be acquired according to the device. The coexistence of smart devices and platforms has rendered the native development approach time and cost consuming. Cross-platform development emerged as a response to these issues. These platforms generate applications for multiple devices based on web languages. Nevertheless, development requires additional implementation based on a native language because of the coverage and functions of supported application programming interfaces (APIs. Wearable devices have recently attracted considerable attention. These devices only support Bluetooth-based interdevice communication, thereby making communication and device control impossible beyond a certain range. We propose Network Application Agent (NetApp-Agent in order to overcome issues. NetApp-Agent based on the Cordova is a wearable device control platform for the development of network applications, controls input/output functions of smartphones and wearable/IoT through the Cordova and Native API, and enables device control and information exchange by external users by offering a self-defined API. We confirmed the efficiency of the proposed platform through experiments and a qualitative assessment of its implementation.

  6. Wideband polarization splitter and rotator with large fabrication tolerance and simple fabrication process

    DEFF Research Database (Denmark)

    Ding, Yunhong; Ou, Haiyan; Peucheret, Christophe

    2013-01-01

    We propose and demonstrate a polarization splitter and rotator (PSR) built on a silicon-on-insulator platform. The PSR is constructed with a tapered waveguide followed by a 2×2 multimode interferometer and can be simply fabricated in a single lithography and etching step. A low insertion loss (....5  dB with minimum insertion loss of 0.6 dB) and a low polarization crosstalk (fabrication tolerance (>50  nm) are experimentally demonstrated....

  7. Linear Polarization Properties of Parsec-Scale AGN Jets

    Directory of Open Access Journals (Sweden)

    Alexander B. Pushkarev

    2017-12-01

    Full Text Available We used 15 GHz multi-epoch Very Long Baseline Array (VLBA polarization sensitive observations of 484 sources within a time interval 1996–2016 from the MOJAVE program, and also from the NRAO data archive. We have analyzed the linear polarization characteristics of the compact core features and regions downstream, and their changes along and across the parsec-scale active galactic nuclei (AGN jets. We detected a significant increase of fractional polarization with distance from the radio core along the jet as well as towards the jet edges. Compared to quasars, BL Lacs have a higher degree of polarization and exhibit more stable electric vector position angles (EVPAs in their core features and a better alignment of the EVPAs with the local jet direction. The latter is accompanied by a higher degree of linear polarization, suggesting that compact bright jet features might be strong transverse shocks, which enhance magnetic field regularity by compression.

  8. Polarized Photocathode R&D for Future Linear Collliders

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, F; Brachmann, A.; Maruyama, T.; Sheppard, J.C.; /SLAC

    2009-01-23

    It is a challenge to generate full charge electrons from the electron sources without compromising polarization for the proposed ILC and CLIC. It is essential to advance polarized photocathodes to meet the requirements. SLAC has worldwide unique dedicated test facilities, Cathode Test System and dc-Gun Test Laboratory, to fully characterize polarized photocathodes. Recent systematic measurements on a strained-well InAlGaAs/AlGaAs cathode at the facilities show that 87% polarization and 0.3% QE are achieved. The QE can be increased to {approx}1.0% with atomic hydrogen cleaning. The surface charge limit at a very low current intensity and the clear dependence of the polarization on the surface charge limit are observed for the first time. On-going programs to develop photocathodes for the ILC and CLIC are briefly introduced.

  9. Instant HTMl5 2D platformer

    CERN Document Server

    Temple, Aidan

    2013-01-01

    Filled with practical, step-by-step instructions and clear explanations for the most important and useful tasks. The step-by-step approach taken by this book will show you how to develop a 2D HTML5 platformer-based game that you will be able to publish to multiple devices.This book is great for anyone who has an interest in HTML5 games development, and who already has a basic to intermediate grasp on both the HTML markup and JavaScript programming languages. Therefore, due to this requirement, the book will not discuss the inner workings of either of these languages but will instead attempt to

  10. Year 2 Report: Protein Function Prediction Platform

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, C E

    2012-04-27

    Upon completion of our second year of development in a 3-year development cycle, we have completed a prototype protein structure-function annotation and function prediction system: Protein Function Prediction (PFP) platform (v.0.5). We have met our milestones for Years 1 and 2 and are positioned to continue development in completion of our original statement of work, or a reasonable modification thereof, in service to DTRA Programs involved in diagnostics and medical countermeasures research and development. The PFP platform is a multi-scale computational modeling system for protein structure-function annotation and function prediction. As of this writing, PFP is the only existing fully automated, high-throughput, multi-scale modeling, whole-proteome annotation platform, and represents a significant advance in the field of genome annotation (Fig. 1). PFP modules perform protein functional annotations at the sequence, systems biology, protein structure, and atomistic levels of biological complexity (Fig. 2). Because these approaches provide orthogonal means of characterizing proteins and suggesting protein function, PFP processing maximizes the protein functional information that can currently be gained by computational means. Comprehensive annotation of pathogen genomes is essential for bio-defense applications in pathogen characterization, threat assessment, and medical countermeasure design and development in that it can short-cut the time and effort required to select and characterize protein biomarkers.

  11. Web Platform for Sharing Modeling Software in the Field of Nonlinear Optics

    Directory of Open Access Journals (Sweden)

    Dubenskaya Julia

    2018-01-01

    Full Text Available We describe the prototype of a Web platform intended for sharing software programs for computer modeling in the rapidly developing field of the nonlinear optics phenomena. The suggested platform is built on the top of the HUBZero open-source middleware. In addition to the basic HUBZero installation we added to our platform the capability to run Docker containers via an external application server and to send calculation programs to those containers for execution. The presented web platform provides a wide range of features and might be of benefit to nonlinear optics researchers.

  12. Experimental platforms for behavioral experiments on social-ecological systems

    Directory of Open Access Journals (Sweden)

    Marco A. Janssen

    2014-12-01

    Full Text Available Recently, there has been an increased interest in using behavioral experiments to study hypotheses on the governance of social-ecological systems. A diversity of software tools are used to implement such experiments. We evaluated various publicly available platforms that could be used in research and education on the governance of social-ecological systems. The aims of the various platforms are distinct, and this is noticeable in the differences in their user-friendliness and their adaptability to novel research questions. The more easily accessible platforms are useful for prototyping experiments and for educational purposes to illustrate theoretical concepts. To advance novel research aims, more elaborate programming experience is required to either implement an experiment from scratch or adjust existing experimental software. There is no ideal platform best suited for all possible use cases, but we have provided a menu of options and their associated trade-offs.

  13. A software platform for the analysis of dermatology images

    Science.gov (United States)

    Vlassi, Maria; Mavraganis, Vlasios; Asvestas, Panteleimon

    2017-11-01

    The purpose of this paper is to present a software platform developed in Python programming environment that can be used for the processing and analysis of dermatology images. The platform provides the capability for reading a file that contains a dermatology image. The platform supports image formats such as Windows bitmaps, JPEG, JPEG2000, portable network graphics, TIFF. Furthermore, it provides suitable tools for selecting, either manually or automatically, a region of interest (ROI) on the image. The automated selection of a ROI includes filtering for smoothing the image and thresholding. The proposed software platform has a friendly and clear graphical user interface and could be a useful second-opinion tool to a dermatologist. Furthermore, it could be used to classify images including from other anatomical parts such as breast or lung, after proper re-training of the classification algorithms.

  14. Development of an MDO platform for aero-structural interactions

    Directory of Open Access Journals (Sweden)

    Hu Zhe

    2017-01-01

    Full Text Available An interactive MDO platform for multivariate and high coupling aero-structural interactions is presented in this paper. Programs based on RSM and GA are utilized as optimization solver, which is connected with CAD/CAE software by a friendly GUI. To generate and modify CAD models in the analysis and optimization process, CATIA Automation Technique is adopted to create a CAD model generator. During the analysis process, high-fidelity models in both disciplines are used. For aircraft wing MDO problems, optimal wing shape and structural configuration can be obtained using this platform in the preliminary design phase. While the current platform is aiming at solving Aero-Structural problems in the preliminary design phase of UAV components, it also provides a reference solution for other related MDO problems. Two cases are provided to verify the validity and practicability of this platform. Besides the design ideas and techniques, this paper also demonstrates its further development capabilities.

  15. Recent progress on HYSPEC, and its polarization analysis capabilities

    Directory of Open Access Journals (Sweden)

    Winn Barry

    2015-01-01

    Full Text Available HYSPEC is a high-intensity, direct-geometry time-of-flight spectrometer at the Spallation Neutron Source, optimized for measurement of excitations in small single-crystal specimens with optional polarization analysis capabilities. The incident neutron beam is monochromated using a Fermi chopper with short, straight blades, and is then vertically focused by Bragg scattering onto the sample position by either a highly oriented pyrolitic graphite (unpolarized or a Heusler (polarized crystal array. Neutrons are detected by a bank of 3He tubes that can be positioned over a wide range of scattering angles about the sample axis. HYSPEC entered the user program in February 2013 for unpolarized experiments, and is already experiencing a vibrant research program. Polarization analysis will be accomplished by using the Heusler crystal array to polarize the incident beam, and either a 3He spin filter or a supermirror wide-angle polarization analyser to analyse the scattered beam. The 3He spin filter employs the spin-exchange optical pumping technique. A 60∘ wide angle 3He cell that matches the detector coverage will be used for polarization analysis. The polarized gas in the post-sample wide angle cell is designed to be periodically and automatically refreshed with an adjustable pressure of polarized gas, optically pumped in a separate cell and then transferred to the wide angle cell. The supermirror analyser has 960 supermirror polarizers distributed over 60∘, and has been characterized at the Swiss Spallation Neutron Source. The current status of the instrument and the development of its polarization analysis capabilities are presented.

  16. Users Polarization on Facebook and Youtube

    Science.gov (United States)

    Bessi, Alessandro; Zollo, Fabiana; Del Vicario, Michela; Puliga, Michelangelo; Scala, Antonio; Caldarelli, Guido; Uzzi, Brian; Quattrociocchi, Walter

    2016-01-01

    Users online tend to select information that support and adhere their beliefs, and to form polarized groups sharing the same view—e.g. echo chambers. Algorithms for content promotion may favour this phenomenon, by accounting for users preferences and thus limiting the exposure to unsolicited contents. To shade light on this question, we perform a comparative study on how same contents (videos) are consumed on different online social media—i.e. Facebook and YouTube—over a sample of 12M of users. Our findings show that content drives the emergence of echo chambers on both platforms. Moreover, we show that the users’ commenting patterns are accurate predictors for the formation of echo-chambers. PMID:27551783

  17. Users Polarization on Facebook and Youtube.

    Science.gov (United States)

    Bessi, Alessandro; Zollo, Fabiana; Del Vicario, Michela; Puliga, Michelangelo; Scala, Antonio; Caldarelli, Guido; Uzzi, Brian; Quattrociocchi, Walter

    2016-01-01

    Users online tend to select information that support and adhere their beliefs, and to form polarized groups sharing the same view-e.g. echo chambers. Algorithms for content promotion may favour this phenomenon, by accounting for users preferences and thus limiting the exposure to unsolicited contents. To shade light on this question, we perform a comparative study on how same contents (videos) are consumed on different online social media-i.e. Facebook and YouTube-over a sample of 12M of users. Our findings show that content drives the emergence of echo chambers on both platforms. Moreover, we show that the users' commenting patterns are accurate predictors for the formation of echo-chambers.

  18. Users Polarization on Facebook and Youtube.

    Directory of Open Access Journals (Sweden)

    Alessandro Bessi

    Full Text Available Users online tend to select information that support and adhere their beliefs, and to form polarized groups sharing the same view-e.g. echo chambers. Algorithms for content promotion may favour this phenomenon, by accounting for users preferences and thus limiting the exposure to unsolicited contents. To shade light on this question, we perform a comparative study on how same contents (videos are consumed on different online social media-i.e. Facebook and YouTube-over a sample of 12M of users. Our findings show that content drives the emergence of echo chambers on both platforms. Moreover, we show that the users' commenting patterns are accurate predictors for the formation of echo-chambers.

  19. Platforms for Innovation and Internationalization

    DEFF Research Database (Denmark)

    Rasmussen, Erik Stavnsager; Petersen, Nicolaj Hannesbo

    2017-01-01

    The high-tech global startup has many challenges related to both innovation and internationalization. From a Danish cluster of Welfare Tech firms, eight innovative and international firms were selected and interviewed. Such firms typically have to be agile and operate in virtual networks in almost...... all parts of their value chains. This article contributes to the understanding of how innovation and internationalization to a great extent are interlinked. The firms have developed a core product or service offering, which the firms often describe as “a platform”. Around the platform, they develop...... their products and services for new customers and users in new countries. The firms have to sustain a strong focus on the platform while at the same time developing their platform solution for new products, new customers, and new markets. This pivoting makes it possible to use the platform in a new context...

  20. Elevated Fixed Platform Test Facility

    Data.gov (United States)

    Federal Laboratory Consortium — The Elevated Fixed Platform (EFP) is a helicopter recovery test facility located at Lakehurst, NJ. It consists of a 60 by 85 foot steel and concrete deck built atop...

  1. Locking devise for oil platforms

    Energy Technology Data Exchange (ETDEWEB)

    Thomas, P.-A.; Naudin, J.-C.

    1987-10-20

    A self-raising oil well platform comprises a shell mounted to be movable along legs by means of raising mechanisms comprising output gear pinions cooperative with racks mounted on at least a part of the length of the legs. The locking device for such a platform comprises a toothed member forming a counter-rack mounted on the shell of the platform, means for shifting the toothed member transversely of the direction of the rack with which the device is associated for engaging or disengaging the teeth of the toothed member in the teeth of the rack, clamping plates connected to the toothed member and clamping counter-plates connected to the platform, and means for clamping the plates and counter-plates together so as to lock the toothed member in position in the rack. 4 figs.

  2. A platform for a smart learning environment

    OpenAIRE

    Simić, Konstantin; Despotović-Zrakić, Marijana; Bojović, Živko; Jovanić, Branislav; Knežević, Đorđe

    2016-01-01

    In this paper, a modular platform which provides student services for smart educational environment is described. The platform represents a point of mutual integration of various services, such as hosting platform for students’ projects, platform for integrating SMS service with students’ web applications, Internet of Things platform which enables acquiring data from sensors distributed within the University building and controlling various actuators. Platform is deployed as a part of Smart L...

  3. Bioma platform advancements during 2017

    OpenAIRE

    FUMAGALLI DAVIDE; NIEMEYER STEFAN

    2017-01-01

    In this report we describe the advancements on the Bioma Framework developed during year 2017. Given that the Bioma platform is quite mature, its core was not recently changed. So that the majority of changes concerns the implementation of the models developed in the platform. Moreover, during 2017 we also set up an alternative version of the framework itself, based on a new developing framework called .NET Core, with the purpose of being able to create a version of Bioma runnable on Linux. ...

  4. Programming F#

    CERN Document Server

    Smith, Chris

    2009-01-01

    Why learn F#? This multi-paradigm language not only offers you an enormous productivity boost through functional programming, it also lets you develop applications using your existing object-oriented and imperative programming skills. With Programming F#, you'll quickly discover the many advantages of Microsoft's new language, which includes access to all the great tools and libraries of the .NET platform. Learn how to reap the benefits of functional programming for your next project -- whether it's quantitative computing, large-scale data exploration, or even a pursuit of your own. With th

  5. Effect of polar and non-polar surfaces of ZnO nanostructures on photocatalytic properties

    International Nuclear Information System (INIS)

    Yang Jinghai; Wang Jian; Li Xiuyan; Lang Jihui; Liu Fuzhu; Yang Lili; Zhai Hongju; Gao Ming; Zhao Xiaoting

    2012-01-01

    Highlights: ► Large-scale arrayed ZnO nanocrystals including ZnO hexagonal platforms and hamburger-like samples have been successfully fabricated by a simple hydrothermal method. ► ZnO with hexagonal platform-like morphology exhibited higher photocatalytic activity compared with that of the hamburger-like ZnO nanostructures. ► The theories of expose surfaces and oxygen vacancies were utilized to explain the photocatalytic mechanism. - Abstract: Large-scale arrayed ZnO nanocrystals with two different expose surfaces, including ZnO hexagonal nanoplatforms with the major expose plane of (0 0 0 1) and hamburger-like samples with the nonpolar planes of {101 ¯ 0} mainly exposed, were successfully fabricated by a simple hydrothermal method. Mechanisms for compare the photocatalytic activity of two typical ZnO nanostructures were systematic explained as the key point in the paper. Compared with the hamburger-like ZnO nanostructures, the ZnO with hexagonal platform-like morphology exhibited improved ability on the photocatalytic degradation of Rhodamine B (RhB) in aqueous solution under UV radiation. The relative higher photocatalytic activity of the ZnO hexagonal nanoplatforms was attributed to the exposed polar surfaces and the content of oxygen vacancy on the nanostructures surface. The Zn-terminated (0 0 0 1) polar face and the surface defects are facile to adsorb O 2− and OH − ions, resulting in a greater production rate of O 2 · − and OH· − , hence promoting the photocatalysis reaction.

  6. Effect of polar and non-polar surfaces of ZnO nanostructures on photocatalytic properties

    Energy Technology Data Exchange (ETDEWEB)

    Yang Jinghai, E-mail: jhyang1@jlnu.edu.cn [Institute of Condensed State Physics, Jilin Normal University, Siping 136000 (China); Key Laboratory of Functional Materials Physics and Chemistry (Jilin Normal University), Ministry of Education, Siping 136000 (China); Wang Jian; Li Xiuyan; Lang Jihui; Liu Fuzhu; Yang Lili; Zhai Hongju; Gao Ming; Zhao Xiaoting [Institute of Condensed State Physics, Jilin Normal University, Siping 136000 (China); Key Laboratory of Functional Materials Physics and Chemistry (Jilin Normal University), Ministry of Education, Siping 136000 (China)

    2012-07-05

    Highlights: Black-Right-Pointing-Pointer Large-scale arrayed ZnO nanocrystals including ZnO hexagonal platforms and hamburger-like samples have been successfully fabricated by a simple hydrothermal method. Black-Right-Pointing-Pointer ZnO with hexagonal platform-like morphology exhibited higher photocatalytic activity compared with that of the hamburger-like ZnO nanostructures. Black-Right-Pointing-Pointer The theories of expose surfaces and oxygen vacancies were utilized to explain the photocatalytic mechanism. - Abstract: Large-scale arrayed ZnO nanocrystals with two different expose surfaces, including ZnO hexagonal nanoplatforms with the major expose plane of (0 0 0 1) and hamburger-like samples with the nonpolar planes of {l_brace}101{sup Macron }0{r_brace} mainly exposed, were successfully fabricated by a simple hydrothermal method. Mechanisms for compare the photocatalytic activity of two typical ZnO nanostructures were systematic explained as the key point in the paper. Compared with the hamburger-like ZnO nanostructures, the ZnO with hexagonal platform-like morphology exhibited improved ability on the photocatalytic degradation of Rhodamine B (RhB) in aqueous solution under UV radiation. The relative higher photocatalytic activity of the ZnO hexagonal nanoplatforms was attributed to the exposed polar surfaces and the content of oxygen vacancy on the nanostructures surface. The Zn-terminated (0 0 0 1) polar face and the surface defects are facile to adsorb O{sup 2-} and OH{sup -} ions, resulting in a greater production rate of O{sup 2}{center_dot}{sup -} and OH{center_dot}{sup -}, hence promoting the photocatalysis reaction.

  7. The COMET Sleep Research Platform.

    Science.gov (United States)

    Nichols, Deborah A; DeSalvo, Steven; Miller, Richard A; Jónsson, Darrell; Griffin, Kara S; Hyde, Pamela R; Walsh, James K; Kushida, Clete A

    2014-01-01

    The Comparative Outcomes Management with Electronic Data Technology (COMET) platform is extensible and designed for facilitating multicenter electronic clinical research. Our research goals were the following: (1) to conduct a comparative effectiveness trial (CET) for two obstructive sleep apnea treatments-positive airway pressure versus oral appliance therapy; and (2) to establish a new electronic network infrastructure that would support this study and other clinical research studies. The COMET platform was created to satisfy the needs of CET with a focus on creating a platform that provides comprehensive toolsets, multisite collaboration, and end-to-end data management. The platform also provides medical researchers the ability to visualize and interpret data using business intelligence (BI) tools. COMET is a research platform that is scalable and extensible, and which, in a future version, can accommodate big data sets and enable efficient and effective research across multiple studies and medical specialties. The COMET platform components were designed for an eventual move to a cloud computing infrastructure that enhances sustainability, overall cost effectiveness, and return on investment.

  8. Canadian Preparations for the International Polar Year 2007-2008

    Science.gov (United States)

    Hik, D. S.; Edwards, K. E.

    2006-12-01

    The launch of the International Polar Year on March 1, 2007 will not only mark the beginning of data collection of innovative scientific programs but it will also unleash a series of innovative education and outreach opportunities to increase public awareness of the polar regions and their global impact. IPY education and outreach programs intend to enhance new methods of communication amongst international scientific partners and organizations; inspire the growth and engagement of the next generation of polar researchers; demystify scientific outcomes of IPY into relevant everyday impacts for the public; and express the wonder and significance of the polar regions through medium of art, exhibits, and writing. Canadian researchers, artists, educators and youth are providing significant leadership in the development of such IPY programming and are involved in almost half of the IPO endorsed EOC proposals. Recognizing that Canada has a critical role to play in IPY as host, leader and participant, preparations in Canada have been extensive. A network of national, territorial, and regional organizing bodies has been established to coordinate the development of the national IPY programs; to support the financial and logistical planning; as well as to facilitate the advancement of international partnerships. The success of the Canadian IPY program, measured as either capacity building, strength of partnerships, or efficiency of logistics and operations, will depend upon having committed partners who are specifically part of the Canadian IPY effort. As the Canadian IPY education and outreach program evolves it is being built firmly on partnerships with existing scientific and education organizations in Canada such as youth organizations, national media corporations, and polar science based programs. By building on existing national strengths we are able to capture the existing energy and activity from IPY 2007-2008 to create a longer term sustainable polar education

  9. Disentangling Competition Among Platform Driven Strategic Groups

    DEFF Research Database (Denmark)

    Kazan, Erol; Tan, Chee-Wee; Lim, Eric

    2015-01-01

    In platform-driven markets, competitive advantage is derived from superior platform design and configurations. For this reason, platform owners strive to create unique and inimitable platform configurals to maintain and extend their competitiveness within network economies. To disentangle firm...... competition within platform-driven markets, we opted for the UK mobile payment market as our empirical setting. By embracing the theoretical lens of strategic groups and digital platforms, this study supplements prior research by deriving a taxonomy of platform-driven strategic groups that is grounded...... on competitive attributes of platform- driven markets; namely interfirm modularity and strategic linkages....

  10. A Typology of Multi-sided Platforms

    DEFF Research Database (Denmark)

    Staykova, Kalina Stefanova; Damsgaard, Jan

    2015-01-01

    In this paper we address how the composition of a platform impacts the platform’s business model. By platform’s business model we mean platform features, platform architecture and platform governance. To this end, we construct the Platform Business Model Framework. We apply the framework to three...... which evolved several steps into being multi-sided (Facebook). Our analysis shows a structural difference between one-sided, two-sided and multi-sided platforms and that platforms consist of a core and potentially also a periphery. The sides of a platform and the ties which connect them can be arranged...

  11. Circularly polarized antennas

    CERN Document Server

    Gao, Steven; Zhu, Fuguo

    2013-01-01

    This book presents a comprehensive insight into the design techniques for different types of CP antenna elements and arrays In this book, the authors address a broad range of topics on circularly polarized (CP) antennas. Firstly, it introduces to the reader basic principles, design techniques and characteristics of various types of CP antennas, such as CP patch antennas, CP helix antennas, quadrifilar helix antennas (QHA), printed quadrifilar helix antennas (PQHA), spiral antenna, CP slot antennas, CP dielectric resonator antennas, loop antennas, crossed dipoles, monopoles and CP horns. Adva

  12. Plasma polarization spectroscopy

    CERN Document Server

    Iwamae, Atsushi

    2008-01-01

    Plasma Polarization Spectroscopy (PPS) is now becoming a standard diagnostic technique for working with laboratory plasmas. This new area needs a comprehensive framework, both experimental and theoretical. This book reviews the historical development of PPS, develops a general theoretical formulation to deal with this phenomenon, along with an overview of relevant cross sections, and reports on laboratory experiments so far performed. It also includes various facets that are interesting from this standpoint, e.g. X-ray lasers and effects of microwave irradiation. It also offers a timely discussion of instrumentation that is quite important in a practical PPS experiment.

  13. Enhanced emission of Nile Red on plasmonic platforms

    Science.gov (United States)

    Synak, Anna; Bojarski, Piotr; Grobelna, Beata; Gryczyński, Ignacy; Fudala, Rafał; Mońka, Michal

    2018-04-01

    Strongly enhanced fluorescence of Nile Red deposited in the vicinity of silver nanoparticles and gold semitransparent mirror was observed. The properties of three different plasmonic platforms based on TiO2, TiO2-GLYMO (1:1) and SiO2 matrices were studied with spectroscopic and microscopic techniques. Significant differences of Nile Red spectroscopic properties in both matrices were observed. In particular, the sensitivity of Nile Red fluorescence enhancement and its peak location to the polarity of local surrounding was found.

  14. System for measuring the proton polarization in a polarized target

    International Nuclear Information System (INIS)

    Karnaukhov, I.M.; Lukhanin, A.A.; Telegin, Yu.N.; Trotsenko, V.I.; Chechetenko, V.F.

    1984-01-01

    The system for measuring the proton polarization in a polarized target representing the high-sensitivity nuclear magnetic resonance (NMR) is described Q-meter with series connection and a circuit for measuring system resonance characteristic is used for NMR-absorption signal recording. Measuring coil is produced of a strip conductor in order to obtain uniform system sensitivity to polarization state in all target volume and improve signal-to-noise ratio. Polarization measuring system operates ion-line with the M-6000 computer. The total measuring error for the value of free proton polarization in target taking into account the error caused by local depolarization of working substance under irradiation by high-intense photon beam is <= 6%. Long-term application of the described system for measuring the proton polarization in the LUEh-20000 accelerator target used in the pion photoproduction experiments has demonstrated its high reliability

  15. Sustaining observations in the polar oceans.

    Science.gov (United States)

    Abrahamsen, E P

    2014-09-28

    Polar oceans present a unique set of challenges to sustained observations. Sea ice cover restricts navigation for ships and autonomous measurement platforms alike, and icebergs present a hazard to instruments deployed in the upper ocean and in shelf seas. However, the important role of the poles in the global ocean circulation provides ample justification for sustained observations in these regions, both to monitor the rapid changes taking place, and to better understand climate processes in these traditionally poorly sampled areas. In the past, the vast majority of polar measurements took place in the summer. In recent years, novel techniques such as miniature CTD (conductivity-temperature-depth) tags carried by seals have provided an explosion in year-round measurements in areas largely inaccessible to ships, and, as ice avoidance is added to autonomous profiling floats and gliders, these promise to provide further enhancements to observing systems. In addition, remote sensing provides vital information about changes taking place in sea ice cover at both poles. To make these observations sustainable into the future, improved international coordination and collaboration is necessary to gain optimum utilization of observing networks. © 2014 The Author(s) Published by the Royal Society. All rights reserved.

  16. Polar drive on OMEGA

    Directory of Open Access Journals (Sweden)

    Radha P.B.

    2013-11-01

    Full Text Available High-convergence polar-drive experiments are being conducted on OMEGA [T. R. Boehly et al., Opt. Commum. 133, 495 (1997] using triple-picket laser pulses. The goal of OMEGA experiments is to validate modeling of oblique laser deposition, heat conduction in the presence of nonradial thermal gradients in the corona, and implosion energetics in the presence of laser–plasma interactions such as crossed-beam energy transfer. Simulated shock velocities near the equator, where the beams are obliquely incident, are within 5% of experimentally inferred values in warm plastic shells, well within the required accuracy for ignition. High, near-one-dimensional areal density is obtained in warm-plastic-shell implosions. Simulated backlit images of the compressing core are in good agreement with measured images. Outstanding questions that will be addressed in the future relate to the role of cross-beam transfer in polar drive irradiation and increasing the energy coupled into the target by decreasing beam obliquity.

  17. Spin exchange in polarized deuterium

    International Nuclear Information System (INIS)

    Przewoski, B. von; Meyer, H.O.; Balewski, J.; Doskow, J.; Ibald, R.; Pollock, R.E.; Rinckel, T.; Wellinghausen, A.; Whitaker, T.J.; Daehnick, W.W.; Haeberli, W.; Schwartz, B.; Wise, T.; Lorentz, B.; Rathmann, F.; Pancella, P.V.; Saha, Swapan K.; Thoerngren-Engblom, P.

    2003-01-01

    We have measured the vector and tensor polarization of an atomic deuterium target as a function of the target density. The polarized deuterium was produced in an atomic beam source and injected into a storage cell. For this experiment, the atomic beam source was operated without rf transitions, in order to avoid complications from the unknown efficiency of these transitions. In this mode, the atomic beam is vector and tensor polarized and both polarizations can be measured simultaneously. We used a 1.2-cm-diam and 27-cm-long storage cell, which yielded an average target density between 3 and 9x10 11 at/cm 3 . We find that the tensor polarization decreases with increasing target density while the vector polarization remains constant. The data are in quantitative agreement with the calculated effect of spin exchange between deuterium atoms at low field

  18. Diving In To Sea Level Rise Using The Polar Explorer ';App'

    Science.gov (United States)

    Turrin, M.; Ryan, W. B.; Bell, R. E.; Pfirman, S. L.; Bell, B.; Porter, D. F.

    2013-12-01

    The vast majority of our lifetime is spent learning outside the classroom, yet the major emphasis in developing climate change instructional materials has been the traditional K16 school environment. The Polar Learning and Responding (PoLAR) project of the National Science Foundation supported Climate Change Education Partnership (CCEP) program chose to move beyond the classroom to focus on lifelong learners, in order to engage the adult population in building public understanding about climate change. Yet reaching individuals who make their own decisions about what and how they choose to learn requires a very different approach to developing educational materials. With an adult audience how we deliver content can be as critical as what we deliver. Using materials and platforms that are readily available and familiar to the user is important. With a significant segment of our time spent connected to smart phones and tablets, employing these platforms to deliver content makes sense. Whether at work, home or in transit, portable devices are critical companions and trusted tools in providing information on everything from the latest news to the daily weather. The world of Apps is equally as familiar to the adult user, so developing an engaging climate App for a portable device offers a successful strategy. The 'Polar Explorer - Sea Level Rise (SLR) App', is one of the new interactive products developed as part of the PoLAR project. Modeled after Columbia's Earth Observer App, a data exploration and data visualization tool, the Polar Explorer SLR App includes a wide range of real Earth data from ocean and atmospheric temperatures to depth of ice layers, underlying topography and human impacts. The Polar Explorer SLR App is grounded in the concept that scientists gain insights into climate change and climate processes through directly examining data. With some scaffolding, the public can gain similar insights using the same data. Structured to be 'question driven' the

  19. Connected Learning: Evaluating and Refining an Academic Community Blogging Platform

    Science.gov (United States)

    Stephens, Michael

    2016-01-01

    This study investigates the benefits of a community blogging platform for students in an online LIS program. Using a web survey and descriptive content analysis methods, this paper empirically addresses how student blogging communities can be effectively foster connections amongst instructors and students, and enhance perceptions of learning…

  20. Resilience of innovation platforms within armed conflicts: the case of ...

    African Journals Online (AJOL)

    The Sub-Saharan Africa Challenge Program moved into the Province in 2008 and established four innovation platforms (IPs) under Integrated Agricultural Research for Development concepts, in Masisi and Rutshuru districts. The objective of this study was to identify mechanisms and strategies used by IPs to continue ...

  1. Creating a Common Platform for HIV Vaccine Research and HIV ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Creating a Common Platform for HIV Vaccine Research and HIV Care and Treatment Program. Second only to South Africa in HIV burden, Nigeria's complex epidemic of HIV viral subtypes is a vital target for HIV vaccine evaluation research. This grant will support a partnership between the Institute of Human ...

  2. Explaining University Students' Effective Use of E-Learning Platforms

    Science.gov (United States)

    Moreno, Valter; Cavazotte, Flavia; Alves, Isabela

    2017-01-01

    Students' success in e-learning programs depends on how they adopt and embed technology into their learning activities. Drawing on the Technology Acceptance Model, we propose a framework to explain students' intention to use e-learning platforms effectively, that is, their intention to fully exploit system's functionalities in leaning processes,…

  3. Linear polarization of BY Draconis

    International Nuclear Information System (INIS)

    Koch, R.H.; Pfeiffer, R.J.

    1976-01-01

    Linear polarization measurements are reported in four bandpasses for the flare star BY Dra. The red polarization is intrinsically variable at a confidence level greater than 99 percent. On a time scale of many months, the variability is not phase-locked to either a rotational or a Keplerian ephemeris. The observations of the three other bandpasses are useful principally to indicate a polarization spectrum rising toward shorter wavelengths

  4. Polarity in Mammalian Epithelial Morphogenesis

    OpenAIRE

    Roignot, Julie; Peng, Xiao; Mostov, Keith

    2013-01-01

    Cell polarity is fundamental for the architecture and function of epithelial tissues. Epithelial polarization requires the intervention of several fundamental cell processes, whose integration in space and time is only starting to be elucidated. To understand what governs the building of epithelial tissues during development, it is essential to consider the polarization process in the context of the whole tissue. To this end, the development of three-dimensional organotypic cell culture model...

  5. The Polarized Radiation Imaging and Spectroscopy Mission

    CERN Document Server

    André, Philippe; Banday, Anthony; Barbosa, Domingos; Barreiro, Belen; Bartlett, James; Bartolo, Nicola; Battistelli, Elia; Battye, Richard; Bendo, George; Benoȋt, Alain; Bernard, Jean-Philippe; Bersanelli, Marco; Béthermin, Matthieu; Bielewicz, Pawel; Bonaldi, Anna; Bouchet, François; Boulanger, François; Brand, Jan; Bucher, Martin; Burigana, Carlo; Cai, Zhen-Yi; Camus, Philippe; Casas, Francisco; Casasola, Viviana; Castex, Guillaume; Challinor, Anthony; Chluba, Jens; Chon, Gayoung; Colafrancesco, Sergio; Comis, Barbara; Cuttaia, Francesco; D'Alessandro, Giuseppe; Da Silva, Antonio; Davis, Richard; de Avillez, Miguel; de Bernardis, Paolo; de Petris, Marco; de Rosa, Adriano; de Zotti, Gianfranco; Delabrouille, Jacques; Désert, François-Xavier; Dickinson, Clive; Diego, Jose Maria; Dunkley, Joanna; Enßlin, Torsten; Errard, Josquin; Falgarone, Edith; Ferreira, Pedro; Ferrière, Katia; Finelli, Fabio; Fletcher, Andrew; Fosalba, Pablo; Fuller, Gary; Galli, Silvia; Ganga, Ken; García-Bellido, Juan; Ghribi, Adnan; Giard, Martin; Giraud-Héraud, Yannick; Gonzalez-Nuevo, Joaquin; Grainge, Keith; Gruppuso, Alessandro; Hall, Alex; Hamilton, Jean-Christophe; Haverkorn, Marijke; Hernandez-Monteagudo, Carlos; Herranz, Diego; Jackson, Mark; Jaffe, Andrew; Khatri, Rishi; Kunz, Martin; Lamagna, Luca; Lattanzi, Massimiliano; Leahy, Paddy; Lesgourgues, Julien; Liguori, Michele; Liuzzo, Elisabetta; Lopez-Caniego, Marcos; Macias-Perez, Juan; Maffei, Bruno; Maino, Davide; Mangilli, Anna; Martinez-Gonzalez, Enrique; Martins, Carlos J.A.P.; Masi, Silvia; Massardi, Marcella; Matarrese, Sabino; Melchiorri, Alessandro; Melin, Jean-Baptiste; Mennella, Aniello; Mignano, Arturo; Miville-Deschênes, Marc-Antoine; Monfardini, Alessandro; Murphy, Anthony; Naselsky, Pavel; Nati, Federico; Natoli, Paolo; Negrello, Mattia; Noviello, Fabio; O'Sullivan, Créidhe; Paci, Francesco; Pagano, Luca; Paladino, Rosita; Palanque-Delabrouille, Nathalie; Paoletti, Daniela; Peiris, Hiranya; Perrotta, Francesca; Piacentini, Francesco; Piat, Michel; Piccirillo, Lucio; Pisano, Giampaolo; Polenta, Gianluca; Pollo, Agnieszka; Ponthieu, Nicolas; Remazeilles, Mathieu; Ricciardi, Sara; Roman, Matthieu; Rosset, Cyrille; Rubino-Martin, Jose-Alberto; Salatino, Maria; Schillaci, Alessandro; Shellard, Paul; Silk, Joseph; Starobinsky, Alexei; Stompor, Radek; Sunyaev, Rashid; Tartari, Andrea; Terenzi, Luca; Toffolatti, Luigi; Tomasi, Maurizio; Trappe, Neil; Tristram, Matthieu; Trombetti, Tiziana; Tucci, Marco; Van de Weijgaert, Rien; Van Tent, Bartjan; Verde, Licia; Vielva, Patricio; Wandelt, Ben; Watson, Robert; Withington, Stafford; Cabrera, Nicolas

    2014-01-01

    PRISM (Polarized Radiation Imaging and Spectroscopy Mission) was proposed to ESA in May 2013 as a large-class mission for investigating within the framework of the ESA Cosmic Vision program a set of important scientific questions that require high resolution, high sensitivity, full-sky observations of the sky emission at wavelengths ranging from millimeter-wave to the far-infrared. PRISM's main objective is to explore the distant universe, probing cosmic history from very early times until now as well as the structures, distribution of matter, and velocity flows throughout our Hubble volume. PRISM will survey the full sky in a large number of frequency bands in both intensity and polarization and will measure the absolute spectrum of sky emission more than three orders of magnitude better than COBE FIRAS. The aim of this Extended White Paper is to provide a more detailed overview of the highlights of the new science that will be made possible by PRISM

  6. Platforms for Innovation and Internationalization

    Directory of Open Access Journals (Sweden)

    Erik Stavnsager Rasmussen

    2017-05-01

    Full Text Available The high-tech global startup has many challenges related to both innovation and internationalization. From a Danish cluster of Welfare Tech firms, eight innovative and international firms were selected and interviewed. Such firms typically have to be agile and operate in virtual networks in almost all parts of their value chains. This article contributes to the understanding of how innovation and internationalization to a great extent are interlinked. The firms have developed a core product or service offering, which the firms often describe as “a platform”. Around the platform, they develop their products and services for new customers and users in new countries. The firms have to sustain a strong focus on the platform while at the same time developing their platform solution for new products, new customers, and new markets. This pivoting makes it possible to use the platform in a new context but is highly demanding for the firms. They need to be extremely agile and fast-moving but at the same time still to have a focus on the core of the firm: the platform.

  7. Integrated polymer polarization rotator based on tilted laser ablation

    Science.gov (United States)

    Poulopoulos, Giannis; Kalavrouziotis, Dimitrios; Missinne, Jeroen; Bosman, Erwin; Van Steenberge, Geert; Apostolopoulos, Dimitrios; Avramopoulos, Hercules

    2017-02-01

    The ubiquitous need for compact, low-cost and mass production photonic devices, for next generation photonic enabled applications, necessitates the development of integrated components exhibiting functionalities that are, to date, carried out by free space elements or standard fiber equipment. The polarization rotator is a typical example of such tendency, as it is a crucial part of the PBS operation of future transceiver modules that leverage polarization multiplexing schemes for increasing the optical network capacity. Up to now, a variety of integrated polarization rotating concepts has been proposed and reported, relying, mainly, on special waveguide crossection configurations for achieving the rotation. Nevertheless, most of those concepts employ SiPh or III-V integration platforms, significantly increasing the fabrication complexity required for customizing the waveguide crossection, which in turn leads to either prohibitively increased cost or compromised quality and performance. In this manuscript we demonstrate the extensive design of a low-cost integrated polymer polarization rotator employing a right-trapezoidal waveguide interfaced to standard square polymer waveguides. First the crossection of the waveguide is defined by calculating and analyzing the components of the hybrid modes excited in the waveguide structure, using a Finite Difference mode solver. Mode overlaps between the fundamental polymer mode and each hybrid mode reveal the optimum lateral offset between the square polymer and the trapezoidal waveguide that ensures both minimum interface loss and maximized polarization rotation performance. The required trapezoidal waveguide length is obtained through EigenMode Expansion (EME) propagation simulations, while more than 95% maximum theoretical conversion efficiency is reported over the entire C-band, resulting to more than 13dB polarization extinction ratio. The polarization rotator design relies on the development of angled polymer waveguide

  8. A polarized alkali ion source

    International Nuclear Information System (INIS)

    Boettger, R.; Tungate, G.; Bauer, B.; Egelhof, P.; Moebius, K.H.; Steffens, E.

    1978-01-01

    The beam foil technique has been applied to detect nuclear vector polarization of a 10 keV 23 Na + beam. The result was about 70% of the atomic beam polarization thus limiting the depolarization by the surface ionizer to at most 30%. In a Coulomb excitation experiment with a tensor polarized 42 MeV 23 Na 7+ beam an effect of 0.011 +- 0.003 was measured yielding a value of t 20 approx. 0.04 for the beam polarization. The depolarization during the acceleration process can be estimated to be about 0.8. (orig.) [de

  9. The SLAC polarized electron source

    International Nuclear Information System (INIS)

    Tang, H.; Alley, R.; Frisch, J.

    1995-06-01

    The SLAC polarized electron source employs a photocathode DC high voltage gun with a loadlock and a YAG pumped Ti:sapphire laser system for colliding beam experiments or a flash lamp pumped Ti:sapphire laser for fixed target experiments. It uses a thin, strained GaAs(100) photocathode, and is capable of producing a pulsed beam with a polarization of ≥80% and a peak current exceeding 10 A. Its operating efficiency has reached 99%. The physics and technology of producing high polarization electron beams from a GaAs photocathode will be reviewed. The prospects of realizing a polarized electron source for future linear colliders will also be discussed

  10. The design of a platform software for CT algorithms investigation

    International Nuclear Information System (INIS)

    Tang Jie; Gao Wenhuan; Xing Yuxiang; Zhang Li

    2006-01-01

    Programming by high level language for CT algorithms can achieve high run-time efficiency. However, the developing work is heavy. Here we show the design of a half-open platform for CT algorithms, which provide the projection data acquisition function and the data visualization function, and can help researchers conveniently extend the reconstruction modules by programming by C ++ language. OOP helps a lot for improving the reusability of reconstruction code. The authors also show a realization of this design. (authors)

  11. The Educational Platform: Constructing Conceptual Frameworks.

    Science.gov (United States)

    Peca, Kathy; Isham, Mark

    2001-01-01

    The education faculty at Eastern New Mexico University used educational platforms as a means of developing the unit's conceptual framework. Faculty members developed personal platforms, then synthesized them into one curricular area platform. The resultant unit educational platform became the basis for the unit's conceptual framework, which…

  12. Stratifying the Develoment of Product Platforms

    DEFF Research Database (Denmark)

    Sköld, Martin; Karlsson, Christer

    2013-01-01

    companies develop platforms for different aims, purposes, and product scopes. Following on from this, the requirements for platform development resources, the ways of organizing platform development, and the implications for management styles have not been explored and are presumably varying. To start...... influencing the project length, requirements for platform development resources, principles for organizing, and implications for management styles....

  13. New offshore platform in the Mexican Gulf

    Energy Technology Data Exchange (ETDEWEB)

    Beisel, T.

    1982-04-01

    After a construction period of only 10 months, the second steel Offshore platform was recently completed in the Mexican Gulf. The pattern for this structure was the Cognac platform. The erection of the new platform, called the 'Cerveza' platform, is described in the article.

  14. Cerveza platforms offer economic options

    Energy Technology Data Exchange (ETDEWEB)

    Leblanc, L.A.

    1982-08-01

    Two single-piece platforms, Cerveze and Cerveza Ligera, were installed by Union Oil Co. in 925-935 ft of water. The technology and equipment used for the two platforms can be used for units to a depth of 1,400 ft in mild climates and to 1,000 ft in more critical weather areas such as the North Sea. The significant improvements in design and procedures in the construction and installation of the Cerveza Ligera platform are: (1) four leg structure, as opposed to eight, requiring less steel; (2) simplified fabrication; and (3) quicker installation. The most significant area of improvement in the Ligera project compared with Cerveza was in communications. Communications between naval architects and onshore launch foremen during loadout, and between surveyors and tug captains during positioning, are cited as examples.

  15. Utilizing platforms in industrialized construction

    DEFF Research Database (Denmark)

    Bonev, Martin; Wörösch, Michael; Hvam, Lars

    2015-01-01

    Purpose – The purpose of this paper is to explore the development of a platform-based projectexecution in the industrialised construction sector, with a focus on systematically balancing cost andvalue. Offering custom-tailored buildings at reasonable costs has been a growing concern for manyconst......Purpose – The purpose of this paper is to explore the development of a platform-based projectexecution in the industrialised construction sector, with a focus on systematically balancing cost andvalue. Offering custom-tailored buildings at reasonable costs has been a growing concern...... methods map structural platformcharacteristics so as to balance commonality and distinctiveness. Originality/value – This paper proposes a general theory of platform-based development andexecution in the industrialised construction sector, which goes beyond concurrent approaches ofstandardising...

  16. Apical polarity in three-dimensional culture systems: where to now?

    Energy Technology Data Exchange (ETDEWEB)

    Inman, J.L.; Bissell, Mina

    2010-01-21

    Delineation of the mechanisms that establish and maintain the polarity of epithelial tissues is essential to understanding morphogenesis, tissue specificity and cancer. Three-dimensional culture assays provide a useful platform for dissecting these processes but, as discussed in a recent study in BMC Biology on the culture of mammary gland epithelial cells, multiple parameters that influence the model must be taken into account.

  17. Moodle vs. Social Media Platforms

    DEFF Research Database (Denmark)

    Gulieva, Valeria

    Given the competition coming from various social media platforms, it is explored in this paper how students could be encouraged to use Moodle more proactively during their studies. Moodle is a course management system for online learning. It is designed to be a flexible template-based system, which......, known and widely used social platforms. It might be also due to the fact that students do not see the benefits in investing time and efforts in learning the new system. Another reason might be the mandatory nature of Moodle, i.e., it is imposed on students, rather than a free choice – and this might...

  18. Microneedle Platforms for Cell Analysis

    KAUST Repository

    Kavaldzhiev, Mincho

    2017-11-01

    Micro-needle platforms are the core components of many recent drug delivery and gene-editing techniques, which allow for intracellular access, controlled cell membrane stress or mechanical trapping of the nucleus. This dissertation work is devoted to the development of micro-needle platforms that offer customized fabrication and new capabilities for enhanced cell analyses. The highest degree of geometrical flexibility is achieved with 3D printed micro-needles, which enable optimizing the topographical stress environment for cells and cell populations of any size. A fabrication process for 3D-printed micro-needles has been developed as well as a metal coating technique based on standard sputter deposition. This extends the functionalities of the platforms by electrical as well as magnetic features. The micro-needles have been tested on human colon cancer cells (HCT116), showing a high degree of biocompatibility of the platform. Moreover, the capabilities of the 3D-printed micro-needles have been explored for drug delivery via the well-established electroporation technique, by coating the micro-needles with gold. Antibodies and fluorescent dyes have been delivered to HCT116 cells and human embryonic kidney cells with a very high transfection rate up to 90%. In addition, the 3D-printed electroporation platform enables delivery of molecules to suspended cells or adherent cells, with or without electroporation buffer solution, and at ultra-low voltages of 2V. In order to provide a micro-needle platform that exploits existing methods for mass fabrication a custom designed template-based process has been developed. It has been used for the production of gold, iron, nickel and poly-pyrrole micro-needles on silicon and glass substrates. A novel delivery method is introduced that activates the micro-needles by electromagnetic induction, which enables to wirelessly gain intracellular access. The method has been successfully tested on HCT116 cells in culture, where a time

  19. Disentangling Competition Among Platform Driven Strategic Groups

    DEFF Research Database (Denmark)

    Kazan, Erol; Tan, Chee-Wee; Lim, Eric T. K.

    2018-01-01

    Digital platforms confer competitive advantage through superior architectural configurations. There is, however, still a dearth of research that sheds light on the competitive attributes that define platform competition from an architectural standpoint. To disentangle platform competition, we opted...... delivery architecture. The preceding attributes of value creation architecture and value delivery architecture aided us in identifying six profiles associated with mobile payment platforms, which in turn led us to advance three competitive strategies that could be pursued by digital platforms in network...

  20. The hydrogen and the fuel cells in the world. Programs and evolutions

    International Nuclear Information System (INIS)

    Lucchese, P.

    2008-01-01

    HyPac is a french platform on the hydrogen and fuel cells, created in 2008. The author presents the opportunity of such a platform facing the world research programs and other existing platforms. (A.L.B.)

  1. Variety of Polarized Line Profiles in Interacting Supernovae

    Science.gov (United States)

    Hoffman, Jennifer L.; Huk, L. N.; Peters, C. L.

    2013-01-01

    The dense circumstellar material that creates strong emission lines in the spectra of interacting supernovae also gives rise to complex line polarization behavior. Viewed in polarized light, the emission line profiles of these supernovae encode information about the geometrical and optical characteristics of their surrounding circumstellar material (CSM) that is inaccessible by other observational techniques. To facilitate quantitative interpretation of these spectropolarimetric signatures, we have created a large grid of model polarized line profiles using a three-dimensional radiative transfer code that simulates polarization via electron and resonant/fluorescent line scattering. The simulated polarized lines take on an array of profile shapes that vary with viewing angle and CSM properties. We present the major results from the grid and investigate the dependence of polarized line profiles on CSM characteristics including temperature, optical depth, and geometry. These results will allow more straightforward interpretation of polarized line profiles in interacting supernovae than has previously been possible. This research is supported by the National Science Foundation through the AAG program and the XSEDE collaboration, and uses the resources of the Texas Advanced Computing Center.

  2. Driving platform for OLED lighting investigations

    Science.gov (United States)

    Vogel, Uwe; Elgner, Andreas; Kreye, Daniel; Amelung, Jörg; Scholles, Michael

    2006-08-01

    OLED technology may be excellently suitable for lighting applications by combining high efficiency, cost effective manufacturing and the use of low cost materials. Certain issues remain to be solved so far, including OLED brightness, color, lifetime, large area uniformity and encapsulation. Another aspect, that might be capable in addressing some of the mentioned issues, is OLED lighting electrical driving. We report on the design of a driving platform for OLED lighting test panels or substrates. It is intended for being a test environment for lighting substrates as well as demonstration/presentation environment. It is based on a 128-channel passive-matrix driver/controller ASIC OC2. Its key component is an MSP430-compatible 16-bit micro-controller core including embedded Flash memory (program), EEPROM (parameter), and RAM (data memory). A significant feature of the device is an electronic approach for improving the lifetime/uniformity behavior of connected OLED. The embedded micro-controller is the key to the high versatility of OC2, since by firmware modification it can be adapted to various applications and conditions. Here its application for an OLED lighting driving platform is presented. Major features of this platform are PC-control mode (via USB interface), stand-alone mode (no external control necessary, just power supply), on-board OLED panel parameter storage, flat geometry of OLED lighting panel carrier (board), AC and DC driving regimes, adjustable reverse voltage, dedicated user SW (PC/Windows-based), sub-tile patterning and single sub-tile control, combination of multiple channels for increasing driving current. This publication contains results of the project "High Brightness OLEDs for ICT & Next Generation Lighting Applications" (OLLA), funded by the European Commission.

  3. Polar Biomedical Research - An Assessment.

    Science.gov (United States)

    1982-10-01

    to grow more crops in subpolar Alaska. The severity of the polar conditions in Antarctica allow no practical method for providing volumes of plant food...for an expanded population. Any experiments in polar regions in food production involving geothermal heat, solar energy, hydroponics , or aquaculture

  4. Create a Polarized Light Show.

    Science.gov (United States)

    Conrad, William H.

    1992-01-01

    Presents a lesson that introduces students to polarized light using a problem-solving approach. After illustrating the concept using a slinky and poster board with a vertical slot, students solve the problem of creating a polarized light show using Polya's problem-solving methods. (MDH)

  5. Carbon nanotube fiber terahertz polarizer

    Energy Technology Data Exchange (ETDEWEB)

    Zubair, Ahmed [Department of Electrical and Computer Engineering, Rice University, Houston, Texas 77005 (United States); Tsentalovich, Dmitri E.; Young, Colin C. [Department of Chemical and Biomolecular Engineering, Rice University, Houston, Texas 77005 (United States); Heimbeck, Martin S. [Charles M. Bowden Laboratory, Aviation & Missile Research, Development, and Engineering Center (AMRDEC), Redstone Arsenal, Alabama 35898 (United States); Everitt, Henry O. [Department of Electrical and Computer Engineering, Rice University, Houston, Texas 77005 (United States); Charles M. Bowden Laboratory, Aviation & Missile Research, Development, and Engineering Center (AMRDEC), Redstone Arsenal, Alabama 35898 (United States); Pasquali, Matteo [Department of Chemical and Biomolecular Engineering, Rice University, Houston, Texas 77005 (United States); Department of Chemistry, Rice University, Houston, Texas 77005 (United States); Department of Materials Science and NanoEngineering, Rice University, Houston, Texas 77005 (United States); Kono, Junichiro, E-mail: kono@rice.edu [Department of Electrical and Computer Engineering, Rice University, Houston, Texas 77005 (United States); Department of Materials Science and NanoEngineering, Rice University, Houston, Texas 77005 (United States); Department of Physics and Astronomy, Rice University, Houston, Texas 77005 (United States)

    2016-04-04

    Conventional, commercially available terahertz (THz) polarizers are made of uniformly and precisely spaced metallic wires. They are fragile and expensive, with performance characteristics highly reliant on wire diameters and spacings. Here, we report a simple and highly error-tolerant method for fabricating a freestanding THz polarizer with nearly ideal performance, reliant on the intrinsically one-dimensional character of conduction electrons in well-aligned carbon nanotubes (CNTs). The polarizer was constructed on a mechanical frame over which we manually wound acid-doped CNT fibers with ultrahigh electrical conductivity. We demonstrated that the polarizer has an extinction ratio of ∼−30 dB with a low insertion loss (<0.5 dB) throughout a frequency range of 0.2–1.1 THz. In addition, we used a THz ellipsometer to measure the Müller matrix of the CNT-fiber polarizer and found comparable attenuation to a commercial metallic wire-grid polarizer. Furthermore, based on the classical theory of light transmission through an array of metallic wires, we demonstrated the most striking difference between the CNT-fiber and metallic wire-grid polarizers: the latter fails to work in the zero-spacing limit, where it acts as a simple mirror, while the former continues to work as an excellent polarizer even in that limit due to the one-dimensional conductivity of individual CNTs.

  6. Polarization-preserving holey fibers

    DEFF Research Database (Denmark)

    Broeng, Jes; Mogilevtsev, Dmitri; Libori, Stig E. Barkou

    2001-01-01

    In this work we suggest and discuss a microstructure of air capillaries with elliptical cross-section in a tread of glass that gives opportunity for Creation of polarization-preserving fiber with very small beat length between the fundamental modes of different polarization...

  7. Polarized Scintillating Targets at Psi

    Science.gov (United States)

    van den Brandt, B.; Bunyatova, E. I.; Hautle, P.; Konter, J. A.; Mango, S.

    2001-02-01

    Scintillating polarized targets are now routinely available: blocks of 18×18×5 mm scintillating organic polymer, doped with TEMPO, polarized dynamically in a field of 2.5 T in a vertical 3He-4He dilution refrigerator. A 19 mm diameter plastic lightguide transports the scintillation light from the sample in the mixing chamber to a photomultiplier outside the cryostat.

  8. UV Coatings, Polarization, and Coronagraphy

    Science.gov (United States)

    Bolcar, Matthew R.; Quijada, Manuel; West, Garrett; Balasubramanian, Bala; Krist, John; Martin, Stefan; Sabatke, Derek

    2016-01-01

    Presenation for the Large UltraViolet Optical Infrared (LUVOIR) and Habitable Exoplanet Imager (HabEx) Science and Technology Definition Teams (STDT) on technical considerations regarding ultraviolet coatings, polarization, and coronagraphy. The presentations review the state-of-the-art in ultraviolet coatings, how those coatings generate polarization aberrations, and recent study results from both the LUVOIR and HabEx teams.

  9. Polarization Imaging and Insect Vision

    Science.gov (United States)

    Green, Adam S.; Ohmann, Paul R.; Leininger, Nick E.; Kavanaugh, James A.

    2010-01-01

    For several years we have included discussions about insect vision in the optics units of our introductory physics courses. This topic is a natural extension of demonstrations involving Brewster's reflection and Rayleigh scattering of polarized light because many insects heavily rely on optical polarization for navigation and communication.…

  10. Climate Drives Polar Bear Origins

    Science.gov (United States)

    In their provocative analysis of northern bears (“Nuclear genomic sequences reveal that polar bears are an old and distinct bear lineage,” Reports, 20 April, p. 344), F. Hailer et al. use independent nuclear loci to show that polar bears originated during the middle Pleistocene, rather than during t...

  11. Safety-Critical Java for Low-End Embedded Platforms

    DEFF Research Database (Denmark)

    Søndergaard, Hans; Korsholm, Stephan E.; Ravn, Anders P.

    2012-01-01

    We present an implementation of the Safety-Critical Java profile (SCJ), targeted for low-end embedded platforms with as little as 16 kB RAM and 256 kB flash. The distinctive features of the implementation are a combination of a lean Java virtual machine (HVM), with a bare metal kernel implementing...... hardware objects, first level interrupt handlers, and native variables, and an infrastructure written in Java which is minimized through program specialization. The HVM allows the implementation to be easily ported to embedded platforms which have a C compiler as part of the development environment...

  12. Communication Platform Payload Definition (CPPD) study. Volume 1: Executive summary

    Science.gov (United States)

    Hunter, E. M.

    1986-01-01

    This is Volume 1 (Executive Summary) of the Ford Aerospace & Communications Corporation Final Report for the Communication Platform Payload Definition (CPPD) Study program conducted for NASA Lewis Research Center under contract No. NAS3-24235. This report presents the results of the study effort leading to five potential platform payloads to service CONUS and WARC Region 2 traffic demand as projected to the year 2008. The report addresses establishing the data bases, developing service aggregation scenarios, selecting and developing 5 payload concepts, performing detailed definition of the 5 payloads, costing them, identifying critical technology, and finally comparing the payloads with each other and also with non-aggregated equivalent services.

  13. Communication Platform Payload Definition (CPPD) study. Volume 3: Addendum

    Science.gov (United States)

    Hunter, E. M.; Driggers, T.; Jorasch, R.

    1986-01-01

    This is Volume 3 (Addendum) of the Ford Aerospace & Communications Corporation Final Report for the Communication Platform Payload Definition (CPPD) Study Program conducted for NASA Lewis Research Center under contract No. NAS3-24235. This report presents the results of the study effort leading to five potential platform payloads to service CONUS and WARC Region 2 traffic demand as projected to the year 2008. The report addresses establishing the data bases, developing service aggregation scenarios, selecting and developing 5 payload concepts, performing detailed definition of the 5 payloads, costing them, identifying critical technology, and finally comparing the payloads with each other and also with non-aggregated equivalent services.

  14. Communication Platform Payload Definition (CPPD) study. Volume 2: Technical report

    Science.gov (United States)

    Hunter, E. M.; Driggers, T.; Jorasch, R.

    1986-01-01

    This is Volume 2 (Technical Report) of the Ford Aerospace & Communications Corporation Final Report for the Communication Platform Payload Definition (CPPD) Study program conducted for NASA Lewis Research Center under contract No. NAS3-24235. This report presents the results of the study effort leading to five potential platform payloads to service CONUS and WARC Region 2 traffic demand as projected to the year 2008. The report addresses establishing the data bases, developing service aggregation scenarios, selecting and developing 5 payload concepts, performing detailed definition of the 5 payloads, costing them, identifying critical technology, and finally comparing the payloads with each other and also with non-aggregated equivalent services.

  15. Polar bear and walrus response to the rapid decline in Arctic sea ice

    Science.gov (United States)

    Oakley, K.; Whalen, M.; Douglas, D.; Udevitz, Mark S.; Atwood, Todd C.; Jay, C.

    2012-01-01

    The Arctic is warming faster than other regions of the world due to positive climate feedbacks associated with loss of snow and ice. One highly visible consequence has been a rapid decline in Arctic sea ice over the past 3 decades - a decline projected to continue and result in ice-free summers likely as soon as 2030. The polar bear (Ursus maritimus) and the Pacific walrus (Odobenus rosmarus divergens) are dependent on sea ice over the continental shelves of the Arctic Ocean's marginal seas. The continental shelves are shallow regions with high biological productivity, supporting abundant marine life within the water column and on the sea floor. Polar bears use sea ice as a platform for hunting ice seals; walruses use sea ice as a resting platform between dives to forage for clams and other bottom-dwelling invertebrates. How have sea ice changes affected polar bears and walruses? How will anticipated changes affect them in the future?

  16. Operation of the optically pumped polarized H- source at LAMPF

    International Nuclear Information System (INIS)

    York, R.L.; Tupa, D.; Swenson, D.R.; van Dyck, O.B.

    1991-01-01

    We report on the first five months of operation of the Optically Pumped Polarized Ion Source (OPPIS) for the nuclear physics research program at LAMPF. The LAMPF OPPIS is unique in using Ti: Sapphire lasers to polarize the potassium charge-exchange medium, and until recently was unique in using a superconducting magnet in the ECR source and polarizer regions. The ECR extraction electrode biasing arrangement is also unique. Typical performance was 25 microamps of peak current (measured at 750 keV) with 55% beam polarization or 15 microamps at 62%. Ion source availability was greater than 90%. We also report our planned improvements in preparation for research operation in May of 1991. 3 refs., 4 figs

  17. Integrins and epithelial cell polarity.

    Science.gov (United States)

    Lee, Jessica L; Streuli, Charles H

    2014-08-01

    Cell polarity is characterised by differences in structure, composition and function between at least two poles of a cell. In epithelial cells, these spatial differences allow for the formation of defined apical and basal membranes. It has been increasingly recognised that cell-matrix interactions and integrins play an essential role in creating epithelial cell polarity, although key gaps in our knowledge remain. This Commentary will discuss the mounting evidence for the role of integrins in polarising epithelial cells. We build a model in which both inside-out signals to polarise basement membrane assembly at the basal surface, and outside-in signals to control microtubule apical-basal orientation and vesicular trafficking are required for establishing and maintaining the orientation of epithelial cell polarity. Finally, we discuss the relevance of the basal integrin polarity axis to cancer. This article is part of a Minifocus on Establishing polarity. © 2014. Published by The Company of Biologists Ltd.

  18. Hyperon polarization: An experimental overview

    International Nuclear Information System (INIS)

    Lach, J.

    1992-12-01

    The fact that inclusively produced hyperons are produced with significant polarization was first discovered at Fermilab about seventeen years ago. This and subsequent experiments showed that Λ degree were produced polarized while bar Λ degree had no polarization in the same kinematical region. This set the stage for many experiments which showed that most hyperons are produced polarized. Recent Fermilab experiments have showed that this phenomena is even more complex than previously thought and theoretical understanding is still lacking. Nevertheless polarized hyperon beams have been an extremely useful experimental tool in measuring hyperon magnetic moments and hyperon β-decay. Recently, hyperon radiative decays have been studied and magnetic moment precession of channeled particles in bent crystals has been observed

  19. A review of polarized ion sources

    International Nuclear Information System (INIS)

    Schmor, P.W.

    1995-06-01

    The two main types of polarized ion sources in use on accelerators today are the Atomic Beam Polarized Ion Source (ABIS) source and the Optically Pumped Polarized Ion Source (OPPIS). Both types can provide beams of nuclearly polarized light ions which are either positively or negatively charged. Heavy ion polarized ion sources for accelerators are being developed. (author). 35 refs., 1 tab

  20. Platform decisions supported by gaming

    DEFF Research Database (Denmark)

    Hansen, Poul H. Kyvsgård; Mikkola, Juliana Hsuan

    2007-01-01

    is the application of on-line games in order to provide training for decision makers and in order to generate overview over the implications of platform decisions. However, games have to be placed in a context with other methods and we argue that a mixture of games, workshops, and simulations can provide improved...

  1. SERS sensors for DVD platform

    DEFF Research Database (Denmark)

    Brøgger, Anna Line

    This Ph.D. thesis explores the engineering of a portable sensor system for detection of rare and small molecules. The Ph.D. project is part of the research project 'Multi-Sensor DVD platform' (MUSE), aiming to integrate different sensors on a rotating disc. The sensors are chosen to complement ea...

  2. 2009 Infrastructure Platform Review Report

    Energy Technology Data Exchange (ETDEWEB)

    Ferrell, John [Office of Energy Efficiency and Renewable Energy (EERE), Washington, DC (United States)

    2009-12-01

    This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the U.S. Department of Energy Biomass program‘s Infrastructure platform review meeting, held on February 19, 2009, at the Marriott Residence Inn, National Harbor, Maryland.

  3. 2009 Feedstocks Platform Review Report

    Energy Technology Data Exchange (ETDEWEB)

    Ferrell, John [Office of Energy Efficiency and Renewable Energy (EERE), Washington, DC (United States)

    2009-12-01

    This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the U.S. Department of Energy Biomass Program‘s Feedstock platform review meeting, held on April 8–10, 2009, at the Grand Hyatt Washington, Washington, D.C.

  4. 2009 Analysis Platform Review Report

    Energy Technology Data Exchange (ETDEWEB)

    Ferrell, John [Office of Energy Efficiency and Renewable Energy (EERE), Washington, DC (United States

    2009-12-01

    This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the U.S. Department of Energy Biomass Program’s Analysis platform review meeting, held on February 18, 2009, at the Marriott Residence Inn, National Harbor, Maryland.

  5. ALLIANCES: simulation platform for radioactive waste disposal

    International Nuclear Information System (INIS)

    Deville, E.; Montarnal, Ph.; Loth, L.; Chavant, C.

    2009-01-01

    CEA, ANDRA and EDF are jointly developing the software platform ALLIANCES whose aim is to produce a tool for the simulation of nuclear waste storage and disposal. This type of simulations deals with highly coupled thermo-hydro-mechanical-chemical and radioactive (T-H-M-C-R) processes. ALLIANCES' aim is to accumulate within the same simulation environment the already acquired knowledge and to gradually integrate new knowledge. The current version of ALLIANCES contains the following modules: - Hydraulics and reactive transport in unsaturated and saturated media; - Multi-phase flow; - Mechanical thermal-hydraulics; - Thermo-Aeraulics; - Chemistry/Transport coupling in saturated media; - Alteration of waste package coupled with the environment; - Sensitivity analysis tools. The next releases will include more physical phenomena like: reactive transport in unsaturated flow and multicomponent multiphase flow; incorporation of responses surfaces in sensitivity analysis tools; integration of parallel numerical codes for flow and transport. Since the distribution of the first release of ALLIANCES (December 2003), the platform was used by ANDRA for his safety simulation program and by CEA for reactive transport simulations (migration of uranium in a soil, diffusion of different reactive species on laboratory samples, glass/iron/clay interaction). (authors)

  6. Synergistic Sensory Platform: Robotic Nurse

    Directory of Open Access Journals (Sweden)

    Dale Wick

    2013-05-01

    Full Text Available This paper presents the concept, structural design and implementation of components of a multifunctional sensory network, consisting of a Mobile Robotic Platform (MRP and stationary multifunctional sensors, which are wirelessly communicating with the MRP. Each section provides the review of the principles of operation and the network components’ practical implementation. The analysis is focused on the structure of the robotic platform, sensory network and electronics and on the methods of the environment monitoring and data processing algorithms that provide maximal reliability, flexibility and stable operability of the system. The main aim of this project is the development of the Robotic Nurse (RN—a 24/7 robotic helper for the hospital nurse personnel. To support long-lasting autonomic operation of the platform, all mechanical, electronic and photonic components were designed to provide minimal weight, size and power consumption, while still providing high operational efficiency, accuracy of measurements and adequateness of the sensor response. The stationary sensors serve as the remote “eyes, ears and noses” of the main MRP. After data acquisition, processing and analysing, the robot activates the mobile platform or specific sensors and cameras. The cross-use of data received from sensors of different types provides high reliability of the system. The key RN capabilities are simultaneous monitoring of physical conditions of a large number of patients and alarming in case of an emergency. The robotic platform Nav-2 exploits innovative principles of any-direction motion with omni-wheels, navigation and environment analysis. It includes an innovative mini-laser, the absorption spectrum analyser and a portable, extremely high signal-to-noise ratio spectrometer with two-dimensional detector array.

  7. COMPASS polarized Drell-Yan experiment

    CERN Document Server

    Doshita, Norihiro

    2016-01-01

    The COMPASS II started at 2012 that includes polarized Drell-Yan program with a polarized solid target. The availability of pion beam provides an access to the Drell-Yan physics throughout the process where quark(target)-antiquark(beam) pair annihilates electromagnetically with a production of dilepton pair. Study of angular dependencies of the Drell-Yan process cross-section allows us to access to parton distribution functions (PDFs) or, more precisely, a convolutions of various PDFs. The transversely polarized target together with negative pion beam is an important feature of the COMPASS Drell-Yan experiment, that provides us with unique data on transverse momentum dependent (TMD) PDFs. After a plot run in 2014, the experiment has just started in 2015. The role of the Drell-Yan experiment at COMPASS in TMD PDFs study, with a comparison to semi-inclusive deep inelastic scattering experiment, is described. The experimental set-up, the status of the data taking in 2015 and preliminary analysis results in the 2...

  8. Suomi National Polar Partnership (SNPP) Environmental Products

    Science.gov (United States)

    Thomas, W.; Grant, K. D.; Miller, S. W.; Jamilkowski, M. L.

    2012-12-01

    The National Oceanic and Atmospheric Administration (NOAA) and National Aeronautics and Space Administration (NASA) are jointly acquiring the next-generation civilian weather and environmental satellite system: the Joint Polar Satellite System (JPSS). JPSS will contribute the afternoon orbit component and ground processing system of the restructured National Polar-orbiting Operational Environmental Satellite System (NPOESS). As such, the Joint Polar Satellite System replaces the current Polar-orbiting Operational Environmental Satellites (POES) managed by the National Oceanic and Atmospheric Administration and the ground processing component of both Polar-orbiting Operational Environmental Satellites and the Defense Meteorological Satellite Program (DMSP) replacement, previously known as the Defense Weather Satellite System (DWSS), managed by the Department of Defense (DoD). The JPSS satellites will carry a suite of sensors designed to collect meteorological, oceanographic, climatological, and solar-geophysical observations of the earth, atmosphere, and space. The ground processing system for JPSS is known as the JPSS Common Ground System (JPSS CGS), and consists of a Command, Control, and Communications Segment (C3S) and an Interface Data Processing Segment (IDPS). Both segments are developed by Raytheon Intelligence and Information Systems (IIS). The C3S currently flies the Suomi National Polar Partnership (Suomi NPP) satellite and transfers mission data from Suomi NPP and between the ground facilities. The IDPS processes Suomi NPP satellite data to provide Environmental Data Records (EDRs) to NOAA and DoD processing centers operated by the United States government. When the JPSS-1 satellite is launched in early 2017, the responsibilities of the C3S and the IDPS will be expanded to support both Suomi NPP and JPSS-1. The Suomi NPP spacecraft launched on October 28, 2011 and is currently undergoing an extensive Calibration and Validation campaign. Given that public

  9. POLARIZED LIGHT IN PHYSIOTHERAPY

    Directory of Open Access Journals (Sweden)

    L. D. Tondiy

    2015-12-01

    Full Text Available The data on polarized light (PS - a new promising treatment, rehabilitation and prevention, which took its deserved place among the known therapeutic physical factors and may even compete with laser radiation of low and LED therapy. It is reflected the significant contribution of domestic scientists in the study of aircraft action on the body, its introduction in the treatment, rehabilitation and prevention of grippe, ARI. These action's mechanisms of the aircraft on the electro-physiological processes in the body that have the leading role in the regulation of its life. The new moment in the study of aircraft on the body is the evidence of its positive impact on the mechanisms of self body - its different units: the disease's banning - a revitalization of the stress-protective, stress-limiting system antioxidial, detoxification and other protection systems, the formation by the body antiviral and antimicrobial specific substances (interferon and lysozyme, activation of the immune system, phagocytosis, protective functions of skin. The protective and mobilizing role of the second link is studied: which is triggered in case of occurrence of disease or preexisting diseases: PL mobilized processes of restitution, reparations, compensation, immunity and microcirculation. The authors studied the possibility of aircraft's using to enhance performance, reduce side effects of physical factors, which are often used in the treatment (electric methods, treatment by sound, fresh and mineral water, etc..

  10. Update of the Polar SWIFT model for polar stratospheric ozone loss (Polar SWIFT version 2)

    Science.gov (United States)

    Wohltmann, Ingo; Lehmann, Ralph; Rex, Markus

    2017-07-01

    The Polar SWIFT model is a fast scheme for calculating the chemistry of stratospheric ozone depletion in polar winter. It is intended for use in global climate models (GCMs) and Earth system models (ESMs) to enable the simulation of mutual interactions between the ozone layer and climate. To date, climate models often use prescribed ozone fields, since a full stratospheric chemistry scheme is computationally very expensive. Polar SWIFT is based on a set of coupled differential equations, which simulate the polar vortex-averaged mixing ratios of the key species involved in polar ozone depletion on a given vertical level. These species are O3, chemically active chlorine (ClOx), HCl, ClONO2 and HNO3. The only external input parameters that drive the model are the fraction of the polar vortex in sunlight and the fraction of the polar vortex below the temperatures necessary for the formation of polar stratospheric clouds. Here, we present an update of the Polar SWIFT model introducing several improvements over the original model formulation. In particular, the model is now trained on vortex-averaged reaction rates of the ATLAS Chemistry and Transport Model, which enables a detailed look at individual processes and an independent validation of the different parameterizations contained in the differential equations. The training of the original Polar SWIFT model was based on fitting complete model runs to satellite observations and did not allow for this. A revised formulation of the system of differential equations is developed, which closely fits vortex-averaged reaction rates from ATLAS that represent the main chemical processes influencing ozone. In addition, a parameterization for the HNO3 change by denitrification is included. The rates of change of the concentrations of the chemical species of the Polar SWIFT model are purely chemical rates of change in the new version, whereas in the original Polar SWIFT model, they included a transport effect caused by the

  11. Cross-platform validation and analysis environment for particle physics

    Energy Technology Data Exchange (ETDEWEB)

    Chekanov, S. V.; Pogrebnyak, I.; Wilbern, D.

    2017-11-01

    A multi-platform validation and analysis framework for public Monte Carlo simulation for high-energy particle collisions is discussed. The front-end of this framework uses the Python programming language, while the back-end is written in Java, which provides a multi-platform environment that can be run from a web browser and can easily be deployed at the grid sites. The analysis package includes all major software tools used in high-energy physics, such as Lorentz vectors, jet algorithms, histogram packages, graphic canvases, and tools for providing data access. This multi-platform software suite, designed to minimize OS-specific maintenance and deployment time, is used for online validation of Monte Carlo event samples through a web interface.

  12. Servo Platform Circuit Design of Pendulous Gyroscope Based on DSP

    Science.gov (United States)

    Tan, Lilong; Wang, Pengcheng; Zhong, Qiyuan; Zhang, Cui; Liu, Yunfei

    2018-03-01

    In order to solve the problem when a certain type of pendulous gyroscope in the initial installation deviation more than 40 degrees, that the servo platform can not be up to the speed of the gyroscope in the rough north seeking phase. This paper takes the digital signal processor TMS320F28027 as the core, uses incremental digital PID algorithm, carries out the circuit design of the servo platform. Firstly, the hardware circuit is divided into three parts: DSP minimum system, motor driving circuit and signal processing circuit, then the mathematical model of incremental digital PID algorithm is established, based on the model, writes the PID control program in CCS3.3, finally, the servo motor tracking control experiment is carried out, it shows that the design can significantly improve the tracking ability of the servo platform, and the design has good engineering practice.

  13. REVEAL: Software Documentation and Platform Migration

    Science.gov (United States)

    Wilson, Michael A.; Veibell, Victoir T.

    2011-01-01

    The Research Environment for Vehicle Embedded Analysis on Linux (REVEAL) is reconfigurable data acquisition software designed for network-distributed test and measurement applications. In development since 2001, it has been successfully demonstrated in support of a number of actual missions within NASA's Suborbital Science Program. Improvements to software configuration control were needed to properly support both an ongoing transition to operational status and continued evolution of REVEAL capabilities. For this reason the project described in this report targets REVEAL software source documentation and deployment of the software on a small set of hardware platforms different from what is currently used in the baseline system implementation. This presentation specifically describes the actions taken over a ten week period by two undergraduate student interns and serves as an overview of the content of the final report for that internship.

  14. [Temperature Measurement with Bluetooth under Android Platform].

    Science.gov (United States)

    Wang, Shuai; Shen, Hao; Luo, Changze

    2015-03-01

    To realize the real-time transmission of temperature data and display using the platform of intelligent mobile phone and bluetooth. Application of Arduino Uno R3 in temperature data acquisition of digital temperature sensor DS18B20 acquisition, through the HC-05 bluetooth transmits the data to the intelligent smart phone Android system, realizes transmission of temperature data. Using Java language to write applications program under Android development environment, can achieve real-time temperature data display, storage and drawing temperature fluctuations drawn graphics. Temperature sensor is experimentally tested to meet the body temperature measurement precision and accuracy. This paper can provide a reference for other smart phone mobile medical product development.

  15. Nuclear physics with polarized particles

    CERN Document Server

    Paetz gen Schieck, Hans

    2012-01-01

    The measurement of spin-polarization observables in reactions of nuclei and particles is of great utility and advantage when the effects of single-spin sub-states are to be investigated. Indeed, the unpolarized differential cross-section encompasses the averaging over the spin states of the particles, and thus loses details of the interaction process. This introductory text combines, in a single volume, course-based lecture notes on spin physics and on polarized-ion sources with the aim of providing a concise yet self-contained starting point for newcomers to the field, as well as for lecturers in search of suitable material for their courses and seminars. A significant part of the book is devoted to introducing the formal theory-a description of polarization and of nuclear reactions with polarized particles. The remainder of the text describes the physical basis of methods and devices necessary to perform experiments with polarized particles and to measure polarization and polarization effects in nuclear rea...

  16. MgII Linear Polarization Measurements Using the MSFC Solar Ultraviolet Magnetograph Sounding Rocket

    Science.gov (United States)

    West, Edward; Cirtain, Jonathan; Kobayashi, Ken; Davis, John; Gary, Allen

    2011-01-01

    This paper will describe the Marshall Space Flight Center's Solar Ultraviolet Magnetograph Investigation (SUMI) sounding rocket program, with emphasis on the polarization characteristics of the VUV optics and their spectral, spatial and polarization resolution. SUMI's first flight (7/30/2010) met all of its mission success criteria and this paper will describe the data that was acquired with emphasis on the MgII linear polarization measurements.

  17. Polarization Signals of Common Spacecraft Materials

    Science.gov (United States)

    Gravseth, Ian; Culp, Robert D.; King, Nicole

    1996-01-01

    This is the final report documenting the results of the polarization testing of near-planar objects with various reflectance properties. The purpose of this investigation was to determine the portion of the reflected signal which is polarized for materials commonly used in space applications. Tests were conducted on several samples, with surface characteristics ranging from highly reflective to relatively dark. The measurements were obtained by suspending the test object in a beam of collimated light. The amount of light falling on the sample was controlled by a circular aperture placed in the light field. The polarized reflectance at various phase angles was then measured. A nonlinear least squares fitting program was used for analysis. For the specular test objects, the reflected signals were measured in one degree increments near the specular point. Otherwise, measurements were taken every five degrees in phase angle. Generally, the more diffuse surfaces had lower polarized reflectances than their more specular counterparts. The reflected signals for the more diffuse surfaces were spread over a larger phase angle range, while the signals from the more specular samples were reflected almost entirely within five degrees of angular deviation from the specular point. The method used to test all the surfaces is presented. The results of this study will be used to support the NASA Orbital Debris Optical Signature Tests. These tests are intended to help better understand the reflectance properties of materials often used in space applications. This data will then be used to improve the capabilities for identification and tracking of space debris.

  18. Few-body experiments with polarized beams and polarized targets

    International Nuclear Information System (INIS)

    Simmons, J.E.

    1983-01-01

    A survey is presented concerning recent polarization experiments in the elastic p-d, p- 3 He, and p- 4 He systems. Mention is made of selected neutron experiments. The nominal energy range is 10 to 1000 MeV. Recent results and interpretations of the p-d system near 10 MeV are discussed. New experiments on the energy dependence of back angle p-d tensor polarization are discussed with respect to resolution of discrepancies and difficulty of theoretical interpretation. Progress is noted concerning multiple scattering interpretation of forward p-d deuteron polarization. Some new results are presented concerning the p- 3 He system and higher energy p- 4 He polarization experiments. 52 references

  19. Blended learning fitting algorithm for polarization curves of fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Fengxiang; Ji, Guangji; Zhang, Chuansheng [School of Automotive Studies of Tongji University, Shanghai 201804 (China); Zhou, Su [School of Automotive Studies of Tongji University, Shanghai 201804 (China); CDHK of Tongji University, Shanghai 200092 (China); Sundmacher, Kai [Max-Planck-Institute for Dynamics of Complex Technical Systems, Magdeburg 39106 (Germany)

    2009-07-15

    Fuel cell polarization curves, characterized by nonlinear models and the parameters of which are time-consuming to be identified, can represent fuel cell performance but will alter as the fuel cell degrades. For getting the information on degradation in time, a less time-consuming and an easily programmed algorithm, based on blended learning technique and linear least square estimation (LSE), is proposed to fit polarization curves obtained from the fuel cell systems. Simulations show that the proposed algorithm, compared with classical nonlinear LSE algorithms, converges much faster, features better extrapolation and less average quadratic error, and is easy to be programmed by C language. Therefore, the algorithm is a good option not only for fitting the polarization curves but also for implementation in embedded systems. (author)

  20. Elite Polarization and Public Opinion

    DEFF Research Database (Denmark)

    Robison, Joshua; Mullinix, Kevin

    2016-01-01

    Elite polarization has reshaped American politics and is an increasingly salient aspect of news coverage within the United States. As a consequence, a burgeoning body of research attempts to unravel the effects of elite polarization on the mass public. However, we know very little about how...... attitudes. In our first study, we show that criticism of polarization leads partisans to more positively evaluate the argument offered by their non-preferred party, increases support for bi-partisanship, but ultimately does not change the extent to which partisans follow their party’s policy endorsements...

  1. Acceleration of polarized proton beams

    International Nuclear Information System (INIS)

    Roser, T.

    1998-01-01

    The acceleration of polarized beams in circular accelerators is complicated by the numerous depolarizing spin resonances. Using a partial Siberian snake and a rf dipole that ensure stable adiabatic spin motion during acceleration has made it possible to accelerate polarized protons to 25 GeV at the Brookhaven AGS. Full Siberian snakes are being developed for RHIC to make the acceleration of polarized protons to 250 GeV possible. A similar scheme is being studied for the 800 GeV HERA proton accelerator

  2. Polarimetry with azimuthally polarized light

    Science.gov (United States)

    de Sande, Juan Carlos González; Piquero, Gemma; Santarsiero, Massimo

    2018-03-01

    Nonuniformly polarized light can be used for Mueller polarimetry of homogeneous linear samples. In this work, a set up based on using azimuthally polarized input light and a modified commercial light polarimeter is proposed and developed. With this set up, a Mueller submatrix of a sample can be obtained by measuring the Stokes parameters at only three different positions across the output beam section. Symmetry constraints for linear deterministic samples allow the complete Mueller matrix to be deduced for this kind of specimens. The experimental results obtained for phase plates and for a linear polarizer confirm the validity of the proposed method.

  3. Polarized deuteron elastic scattering from a polarized proton target

    International Nuclear Information System (INIS)

    Schmelzer, R.; Kuiper, H.; Schoeberl, M.; Berber, S.; Hilmert, H.; Koeppel, R.; Pferdmenges, R.; Zankel, H.

    1983-01-01

    Measurements are reported of the spin correlation parameter Cy,y for the elastic scattering of 10.0 MeV vector polarized deuterons from a polarized proton target at five CM angles (76 0 ,85 0 ,98 0 ,115 0 ,132 0 ). The experimental results are compared with different predictions. A Faddeev type calculation on the basis of local potentials also including approximate Coulomb distortion is favoured by our experimental results. (orig.)

  4. PolarHub: A Global Hub for Polar Data Discovery

    Science.gov (United States)

    Li, W.

    2014-12-01

    This paper reports the outcome of a NSF project in developing a large-scale web crawler PolarHub to discover automatically the distributed polar dataset in the format of OGC web services (OWS) in the cyberspace. PolarHub is a machine robot; its goal is to visit as many webpages as possible to find those containing information about polar OWS, extract this information and store it into the backend data repository. This is a very challenging task given huge data volume of webpages on the Web. Three unique features was introduced in PolarHub to make it distinctive from earlier crawler solutions: (1) a multi-task, multi-user, multi-thread support to the crawling tasks; (2) an extensive use of thread pool and Data Access Object (DAO) design patterns to separate persistent data storage and business logic to achieve high extendibility of the crawler tool; (3) a pattern-matching based customizable crawling algorithm to support discovery of multi-type geospatial web services; and (4) a universal and portable client-server communication mechanism combining a server-push and client pull strategies for enhanced asynchronous processing. A series of experiments were conducted to identify the impact of crawling parameters to the overall system performance. The geographical distribution pattern of all PolarHub identified services is also demonstrated. We expect this work to make a major contribution to the field of geospatial information retrieval and geospatial interoperability, to bridge the gap between data provider and data consumer, and to accelerate polar science by enhancing the accessibility and reusability of adequate polar data.

  5. Development of integrated platform for computational material design

    International Nuclear Information System (INIS)

    Kiyoshi, Matsubara; Kumi, Itai; Nobutaka, Nishikawa; Akifumi, Kato; Hideaki, Koike

    2003-01-01

    The goal of our project is to design and develop a problem-solving environment (PSE) that will help computational scientists and engineers develop large complicated application software and simulate complex phenomena by using networking and parallel computing. The integrated platform, which is designed for PSE in the Japanese national project of Frontier Simulation Software for Industrial Science, is defined by supporting the entire range of problem solving activity from program formulation and data setup to numerical simulation, data management, and visualization. A special feature of our integrated platform is based on a new architecture called TASK FLOW. It integrates the computational resources such as hardware and software on the network and supports complex and large-scale simulation. This concept is applied to computational material design and the project 'comprehensive research for modeling, analysis, control, and design of large-scale complex system considering properties of human being'. Moreover this system will provide the best solution for developing large and complicated software and simulating complex and large-scaled phenomena in computational science and engineering. A prototype has already been developed and the validation and verification of an integrated platform will be scheduled by using the prototype in 2003. In the validation and verification, fluid-structure coupling analysis system for designing an industrial machine will be developed on the integrated platform. As other examples of validation and verification, integrated platform for quantum chemistry and bio-mechanical system are planned

  6. Remote sensing image segmentation based on Hadoop cloud platform

    Science.gov (United States)

    Li, Jie; Zhu, Lingling; Cao, Fubin

    2018-01-01

    To solve the problem that the remote sensing image segmentation speed is slow and the real-time performance is poor, this paper studies the method of remote sensing image segmentation based on Hadoop platform. On the basis of analyzing the structural characteristics of Hadoop cloud platform and its component MapReduce programming, this paper proposes a method of image segmentation based on the combination of OpenCV and Hadoop cloud platform. Firstly, the MapReduce image processing model of Hadoop cloud platform is designed, the input and output of image are customized and the segmentation method of the data file is rewritten. Then the Mean Shift image segmentation algorithm is implemented. Finally, this paper makes a segmentation experiment on remote sensing image, and uses MATLAB to realize the Mean Shift image segmentation algorithm to compare the same image segmentation experiment. The experimental results show that under the premise of ensuring good effect, the segmentation rate of remote sensing image segmentation based on Hadoop cloud Platform has been greatly improved compared with the single MATLAB image segmentation, and there is a great improvement in the effectiveness of image segmentation.

  7. YARP: Yet Another Robot Platform

    Directory of Open Access Journals (Sweden)

    Lorenzo Natale

    2008-11-01

    Full Text Available We describe YARP, Yet Another Robot Platform, an open-source project that encapsulates lessons from our experience in building humanoid robots. The goal of YARP is to minimize the effort devoted to infrastructure-level software development by facilitating code reuse, modularity and so maximize research-level development and collaboration. Humanoid robotics is a "bleeding edge" field of research, with constant flux in sensors, actuators, and processors. Code reuse and maintenance is therefore a significant challenge. We describe the main problems we faced and the solutions we adopted. In short, the main features of YARP include support for inter-process communication, image processing as well as a class hierarchy to ease code reuse across different hardware platforms. YARP is currently used and tested on Windows, Linux and QNX6 which are common operating systems used in robotics.

  8. Stabilisation problem in biaxial platform

    Science.gov (United States)

    Lindner, Tymoteusz; Rybarczyk, Dominik; Wyrwał, Daniel

    2016-12-01

    The article describes investigation of rolling ball stabilization problem on a biaxial platform. The aim of the control system proposed here is to stabilize ball moving on a plane in equilibrium point. The authors proposed a control algorithm based on cascade PID and they compared it with another control method. The article shows the results of the accuracy of ball stabilization and influence of applied filter on the signal waveform. The application used to detect the ball position measured by digital camera has been written using a cross platform .Net wrapper to the OpenCV image processing library - EmguCV. The authors used the bipolar stepper motor with dedicated electronic controller. The data between the computer and the designed controller are sent with use of the RS232 standard. The control stand is based on ATmega series microcontroller.

  9. Stabilisation problem in biaxial platform

    Directory of Open Access Journals (Sweden)

    Lindner Tymoteusz

    2016-12-01

    Full Text Available The article describes investigation of rolling ball stabilization problem on a biaxial platform. The aim of the control system proposed here is to stabilize ball moving on a plane in equilibrium point. The authors proposed a control algorithm based on cascade PID and they compared it with another control method. The article shows the results of the accuracy of ball stabilization and influence of applied filter on the signal waveform. The application used to detect the ball position measured by digital camera has been written using a cross platform .Net wrapper to the OpenCV image processing library - EmguCV. The authors used the bipolar stepper motor with dedicated electronic controller. The data between the computer and the designed controller are sent with use of the RS232 standard. The control stand is based on ATmega series microcontroller.

  10. Tax Responses in Platform Industries

    DEFF Research Database (Denmark)

    Kind, Hans Jarle; Köthenbürger, Marko; Schjelderup, Guttorm

    Two-sided platform firms serve distinct customer groups that are connected through interdependent demand, and include major businesses such as the media industry, banking, and the software industry. A well known result of tax incidence is that consumers of a more heavily taxed good pay a higher...... price and thus buy less of the good. The present paper shows that this result need not hold in a two-sided market. On the contrary, a higher ad valorem tax may lower end-user prices and spur sales. Thus, two-sided platform firms may not at all engage in tax shifting via price increases. We further show...... that a higher ad valorem tax may undermine a firm's incentive to differentiate its product from that of its competitors. Finally, we demonstrate that the effects of increasing specific taxes may be the opposite of those of increasing value added taxes....

  11. Climate News Across Media Platforms

    DEFF Research Database (Denmark)

    Eskjær, Mikkel Fugl

    2015-01-01

    In a changing media landscape marked by technological, institutional and cultural convergence, comparative and cross-media content analysis represents a valuable analytical tool in mapping the diverse channels of climate change communication. This paper presents a comparative study of climate...... change news on five different media platforms: newspapers, television, radio, web-news and mobile news. It investigates the themes and actors represented in public climate change communication as well as the diverse possibilities of participating in public debates and information sharing. By combining...... quantitative and qualitative content analysis the paper documents and explores the extent and character of climate change news across different media platforms. The study aims at contributing to the on-going assessment of how news media are addressing climate change at a time when old and new media...

  12. DATABASE REPLICATION IN HETEROGENOUS PLATFORM

    OpenAIRE

    Hendro Nindito; Evaristus Didik Madyatmadja; Albert Verasius Dian Sano

    2014-01-01

    The application of diverse database technologies in enterprises today is increasingly a common practice. To provide high availability and survavibality of real-time information, a database replication technology that has capability to replicate databases under heterogenous platforms is required. The purpose of this research is to find the technology with such capability. In this research, the data source is stored in MSSQL database server running on Windows. The data will be replicated to MyS...

  13. The Innovative Capabilities Of Digital Payment Platforms

    DEFF Research Database (Denmark)

    Kazan, Erol

    2015-01-01

    the intended conjoint commercialization efforts. Furthermore, the architectural design of digital platforms impacts the access to commercialization, resulting to an exclusion or inclusion strategy in accessing value opportunities. Our findings contribute to the open innovation and digital platform literature......This study presents a model for studying the innovative capabilities of digital payment platforms in regards to open innovation integration and commercialization. We perceive digital platforms as layered modular IT artifacts, where platform governance and the configuration of platform layers impact...... the support for open innovation. The proposed model has been employed in a comparative case study between two digital payment platforms: Apple Pay and Google Wallet. The findings suggest that digital payment platforms make use of boundary resources to be highly integrative or integratable, which supports...

  14. Towards a Framework of Digital Platform Competition

    DEFF Research Database (Denmark)

    Kazan, Erol; Tan, Chee-Wee; Lim, Eric T. K.

    2016-01-01

    This paper advances a framework for examining the competitive principles of mobile payment platforms. We postulate that the strategic interplay of platform layers will drive the competitive dynamics of platform-driven ubiquitous systems. This framework has been employed in a comparative case study...... between monopolistic (i.e., Pingit) and federated (i.e., Paym) mobile payment platforms to illustrate its applicability and yield principles on the nature and impact of competition among platform-driven ubiquitous systems. Preliminary findings indicate that monopolistic mobile digital platforms attempt...... to create unique configurals to obtain monopolistic power by tightly coupling platform layers, which are difficult to replicate. Conversely, federated digital platforms compete by dispersing the service layer to harness the collective resources from individual firms. Furthermore, the interaction...

  15. The Logic of Digital Platform Disruption

    DEFF Research Database (Denmark)

    Kazan, Erol; Tan, Chee-Wee; Lim, Eric T. K.

    Digital platforms are disruptive IT artifacts, because they facilitate the quick release of innovative platform derivatives from third parties (e.g., apps). This study endeavours to unravel the disruptive potential, caused by distinct designs and configurations of digital platforms on market...... environments. We postulate that the disruptive potential of digital platforms is determined by the degree of alignment among the business, technology and platform profiles. Furthermore, we argue that the design and configuration of the aforementioned three elements dictates the extent to which open innovation...... is permitted. To shed light on the disruptive potential of digital platforms, we opted for payment platforms as our unit of analysis. Through interviews with experts and payment providers, we seek to gain an in-depth appreciation of how contemporary digital payment platforms are designed and configured...

  16. Benchmarking computer platforms for lattice QCD applications

    International Nuclear Information System (INIS)

    Hasenbusch, M.; Jansen, K.; Pleiter, D.; Wegner, P.; Wettig, T.

    2003-09-01

    We define a benchmark suite for lattice QCD and report on benchmark results from several computer platforms. The platforms considered are apeNEXT, CRAY T3E, Hitachi SR8000, IBM p690, PC-Clusters, and QCDOC. (orig.)

  17. Benchmarking computer platforms for lattice QCD applications

    International Nuclear Information System (INIS)

    Hasenbusch, M.; Jansen, K.; Pleiter, D.; Stueben, H.; Wegner, P.; Wettig, T.; Wittig, H.

    2004-01-01

    We define a benchmark suite for lattice QCD and report on benchmark results from several computer platforms. The platforms considered are apeNEXT, CRAY T3E; Hitachi SR8000, IBM p690, PC-Clusters, and QCDOC

  18. Software development on the SAP HANA platform

    CERN Document Server

    Walker, Mark

    2013-01-01

    Software Development on the SAP HANA Platform is a general tutorial guide to SAP HANA.This book is written for beginners to the SAP HANA platform. No knowledge of SAP HANA is necessary to start using this book.

  19. Hierarchical DSE for multi-ASIP platforms

    DEFF Research Database (Denmark)

    Micconi, Laura; Corvino, Rosilde; Gangadharan, Deepak

    2013-01-01

    This work proposes a hierarchical Design Space Exploration (DSE) for the design of multi-processor platforms targeted to specific applications with strict timing and area constraints. In particular, it considers platforms integrating multiple Application Specific Instruction Set Processors (ASIPs...

  20. Product Platform Development in Industrial Networks

    DEFF Research Database (Denmark)

    Karlsson, Christer; Skold, Martin

    2011-01-01

    The article examines the strategic issues involved in the deployment of product platform development in an industrial network. The move entails identifying the types and characteristics of generically different product platform strategies and clarifying strategic motives and differences. Number...

  1. Small animal radiotherapy research platforms

    International Nuclear Information System (INIS)

    Verhaegen, Frank; Granton, Patrick; Tryggestad, Erik

    2011-01-01

    Advances in conformal radiation therapy and advancements in pre-clinical radiotherapy research have recently stimulated the development of precise micro-irradiators for small animals such as mice and rats. These devices are often kilovolt x-ray radiation sources combined with high-resolution CT imaging equipment for image guidance, as the latter allows precise and accurate beam positioning. This is similar to modern human radiotherapy practice. These devices are considered a major step forward compared to the current standard of animal experimentation in cancer radiobiology research. The availability of this novel equipment enables a wide variety of pre-clinical experiments on the synergy of radiation with other therapies, complex radiation schemes, sub-target boost studies, hypofractionated radiotherapy, contrast-enhanced radiotherapy and studies of relative biological effectiveness, to name just a few examples. In this review we discuss the required irradiation and imaging capabilities of small animal radiation research platforms. We describe the need for improved small animal radiotherapy research and highlight pioneering efforts, some of which led recently to commercially available prototypes. From this, it will be clear that much further development is still needed, on both the irradiation side and imaging side. We discuss at length the need for improved treatment planning tools for small animal platforms, and the current lack of a standard therein. Finally, we mention some recent experimental work using the early animal radiation research platforms, and the potential they offer for advancing radiobiology research. (topical review)

  2. Small animal radiotherapy research platforms

    Energy Technology Data Exchange (ETDEWEB)

    Verhaegen, Frank; Granton, Patrick [Department of Radiation Oncology (MAASTRO), GROW-School for Oncology and Developmental Biology, Maastricht University Medical Center, Maastricht 6201 BN (Netherlands); Tryggestad, Erik, E-mail: frank.verhaegen@maastro.nl [Department of Radiation Oncology and Molecular Radiation Sciences, The Johns Hopkins University School of Medicine, Baltimore, MD 21231 (United States)

    2011-06-21

    Advances in conformal radiation therapy and advancements in pre-clinical radiotherapy research have recently stimulated the development of precise micro-irradiators for small animals such as mice and rats. These devices are often kilovolt x-ray radiation sources combined with high-resolution CT imaging equipment for image guidance, as the latter allows precise and accurate beam positioning. This is similar to modern human radiotherapy practice. These devices are considered a major step forward compared to the current standard of animal experimentation in cancer radiobiology research. The availability of this novel equipment enables a wide variety of pre-clinical experiments on the synergy of radiation with other therapies, complex radiation schemes, sub-target boost studies, hypofractionated radiotherapy, contrast-enhanced radiotherapy and studies of relative biological effectiveness, to name just a few examples. In this review we discuss the required irradiation and imaging capabilities of small animal radiation research platforms. We describe the need for improved small animal radiotherapy research and highlight pioneering efforts, some of which led recently to commercially available prototypes. From this, it will be clear that much further development is still needed, on both the irradiation side and imaging side. We discuss at length the need for improved treatment planning tools for small animal platforms, and the current lack of a standard therein. Finally, we mention some recent experimental work using the early animal radiation research platforms, and the potential they offer for advancing radiobiology research. (topical review)

  3. Communications platform payload definition study

    Science.gov (United States)

    Clopp, H. W.; Hawkes, T. A.; Bertles, C. R.; Pontano, B. A.; Kao, T.

    1986-01-01

    Large geostationary communications platforms were investigated in a number of studies since 1974 as a possible means to more effectively utilize the geostationary arc and electromagnetic spectrum and to reduce overall satellite communications system costs. The commercial feasibility of various communications platform payload concepts circa 1998 was addressed. Promising payload concepts were defined, recurring costs were estimated, and critical technologies needed to enable eventual commercialization were identified. Ten communications service aggregation scenarios describing potential groupings of service were developed for a range of conditions. Payload concepts were defined for four of these scenarios: (1) Land Mobile Satellite Service (LMSS) meets 100% of Contiguous United States (CONUS) plus Canada demand with a single platform; (2) Fixed Satellite Service (FSS) (trunking + Customer Premises Service (CPS)), meet 20% of CONUS demand;(3) FSS (trunking + CPS + video distribution), 10 to 13% of CONUS demand; and (4) FSS (20% of demand) + Inter Satellite Links (ISL) + Tracking and Data Relay Satellite System (TDRSS)/Tracking and Data Acquisition System (TDAS) Data Distribution.

  4. Microarray platform for omics analysis

    Science.gov (United States)

    Mecklenburg, Michael; Xie, Bin

    2001-09-01

    Microarray technology has revolutionized genetic analysis. However, limitations in genome analysis has lead to renewed interest in establishing 'omic' strategies. As we enter the post-genomic era, new microarray technologies are needed to address these new classes of 'omic' targets, such as proteins, as well as lipids and carbohydrates. We have developed a microarray platform that combines self- assembling monolayers with the biotin-streptavidin system to provide a robust, versatile immobilization scheme. A hydrophobic film is patterned on the surface creating an array of tension wells that eliminates evaporation effects thereby reducing the shear stress to which biomolecules are exposed to during immobilization. The streptavidin linker layer makes it possible to adapt and/or develop microarray based assays using virtually any class of biomolecules including: carbohydrates, peptides, antibodies, receptors, as well as them ore traditional DNA based arrays. Our microarray technology is designed to furnish seamless compatibility across the various 'omic' platforms by providing a common blueprint for fabricating and analyzing arrays. The prototype microarray uses a microscope slide footprint patterned with 2 by 96 flat wells. Data on the microarray platform will be presented.

  5. High index contrast photonics platform

    Science.gov (United States)

    Chu, Sai T.; Little, Brent E.; Hryniewicz, John V.; Johnson, Fred G.; King, Oliver; Gill, Dave; Chen, Wenlu; Chen, Wei

    2005-10-01

    A new low-loss high-index-contrast photonics platform has been developed for integrated optics and microwave photonics. The platform consists of a material system that has an index contrast that is adjustable from 0 to 25% and which is processed using conventional CMOS tools. The platform allows one to four orders of magnitude reduction in the size of optical components compared with conventional planar technologies. As an example, meter long path lengths occupy coils that are millimeters in diameter. Microwave photonic building blocks that are enabled include large bit count programmable delay lines for beam steering and shaping that fit in less than a square centimeter and which have delays controllable from 5 fsec to 10 nsec. Also enabled are arrays of high order tunable filters, a hundred micrometers in size, having linewidths ranging from tens of MHz to tens of GHz. These filters can be tuned over several hundred GHz, and when placed in Vernier architectures can be tuned across the C band (5 THz). An optical chip typically consists of dozens of optical elements. Each element is placed in its own micro-control loop that consists of a thin film heater for thermo-optic control and a thermistor for electronic feedback. The micro-control loops impart intelligence to the optical chip.

  6. A table-top PXI based low-field spectrometer for solution dynamic nuclear polarization.

    Science.gov (United States)

    Biller, Joshua R; Stupic, Karl F; Moreland, J

    2018-03-01

    We present the development of a portable dynamic nuclear polarization (DNP) instrument based on the PCI eXtensions for Instrumentation platform. The main purpose of the instrument is for study of 1 H polarization enhancements in solution through the Overhauser mechanism at low magnetic fields. A DNP probe set was constructed for use at 6.7 mT, using a modified Alderman-Grant resonator at 241 MHz for saturation of the electron transition. The solenoid for detection of the enhanced 1 H signal at 288 kHz was constructed with Litz wire. The largest observed 1 H enhancements (ε) at 6.7 mT for 14 N-CTPO radical in air saturated aqueous solution was ε~65. A concentration dependence of the enhancement is observed, with maximum ε at 5.5 mM. A low resonator efficiency for saturation of the electron paramagnetic resonance transition results in a decrease in ε for the 10.3 mM sample. At high incident powers (42 W) and long pump times, capacitor heating effects can also decrease the enhancement. The core unit and program described here could be easily adopted for multi-frequency DNP work, depending on available main magnets and selection of the "plug and play" arbitrary waveform generator, digitizer, and radiofrequency synthesizer PCI eXtensions for Instrumentatione cards. Published 2017. This article is a U.S. Government work and is in the public domain in the USA.

  7. Polar source analysis : technical memorandum

    Science.gov (United States)

    2017-09-29

    The following technical memorandum describes the development, testing and analysis of various polar source data sets. The memorandum also includes recommendation for potential inclusion in future releases of AEDT. This memorandum is the final deliver...

  8. Anodic Concentration Polarization in SOFCs

    Energy Technology Data Exchange (ETDEWEB)

    Williford, Rick E.; Chick, Lawrence A.; Maupin, Gary D.; Simner, Steve P.; Stevenson, Jeffry W.; Khaleel, Mohammad A.; Wachsman, ED, et al

    2003-08-01

    Concentration polarization is important because it determines the maximum power output of a solid oxide fuel cell (SOFC) at high fuel utilization. Anodic concentration polarization occurs when the demand for reactants exceeds the capacity of the porous ceramic anode to supply them by gas diffusion mechanisms. High tortuosities (bulk diffusion resistances) are often assumed to explain this behavior. However, recent experiments show that anodic concentration polarization originates in the immediate vicinity of the reactive triple phase boundary (TPB) sites near the anode/electrolyte interface. A model is proposed to describe how concentration polarization is controlled by two localized phenomena: competitive adsorption of reactants in areas adjacent to the reactive TPB sites, followed by relatively slow surface diffusion to the reactive sites. Results suggest that future SOFC design improvements should focus on optimization of the reactive area, adsorption, and surface diffusion at the anode/electrolyte interface.

  9. The definition of cross polarization

    DEFF Research Database (Denmark)

    Ludwig, Arthur

    1973-01-01

    There are at least three different definitions of cross polarization used in the literature. The alternative definitions are discussed with respect to several applications, and the definition which corresponds to one standard measurement practice is proposed as the best choice....

  10. Dynamic elections and ideological polarization

    Czech Academy of Sciences Publication Activity Database

    Nunnari, S.; Zápal, Jan

    2017-01-01

    Roč. 25, č. 4 (2017), s. 505-534 ISSN 1047-1987 Institutional support: Progres-Q24 Keywords : elections * political polarization Subject RIV: AH - Economics OBOR OECD: Economic Theory Impact factor: 3.361, year: 2016

  11. Dynamic elections and ideological polarization

    Czech Academy of Sciences Publication Activity Database

    Nunnari, S.; Zápal, Jan

    2017-01-01

    Roč. 25, č. 4 (2017), s. 505-534 ISSN 1047-1987 Institutional support: RVO:67985998 Keywords : elections * political polarization Subject RIV: AH - Economics OBOR OECD: Economic Theory Impact factor: 3.361, year: 2016

  12. Polarization at LEP. Vol. 2

    International Nuclear Information System (INIS)

    Alexander, G.; Altarelli, G.; Blondel, A.; Coignet, G.; Keil, E.; Plane, D.E.; Treille, D.

    1988-01-01

    This report contains a collection of papers covering the most important part of studies carried out by five study groups in view of a programme of experiments with polarized beams at LEP, the Large Electron-Positron collider under construction at CERN. The emphasis is on precision measurements at the Z peak. Such measurements are shown to be of considerable theoretical interest as well as very clean from the point of view of theoretical and experimental uncertainties. The measurement of the beam polarization can certainly be performed with sufficient accuracy, thanks to the availability of both e + and e - beam polarization. The normalization of the data taken with different beam helicities poses certain constraints that are described. Substantial progress has been made in understanding the possibility of providing longitudinally polarized beams in the LEP machine: The design of new wigglers and spin rotators, the study of correction procedures and results of numerical simulations are presented. (orig.)

  13. Mechanical writing of ferroelectric polarization.

    Science.gov (United States)

    Lu, H; Bark, C-W; Esque de los Ojos, D; Alcala, J; Eom, C B; Catalan, G; Gruverman, A

    2012-04-06

    Ferroelectric materials are characterized by a permanent electric dipole that can be reversed through the application of an external voltage, but a strong intrinsic coupling between polarization and deformation also causes all ferroelectrics to be piezoelectric, leading to applications in sensors and high-displacement actuators. A less explored property is flexoelectricity, the coupling between polarization and a strain gradient. We demonstrate that the stress gradient generated by the tip of an atomic force microscope can mechanically switch the polarization in the nanoscale volume of a ferroelectric film. Pure mechanical force can therefore be used as a dynamic tool for polarization control and may enable applications in which memory bits are written mechanically and read electrically.

  14. Mechanical Writing of Ferroelectric Polarization

    Science.gov (United States)

    Lu, H.; Bark, C.-W.; Esque de los Ojos, D.; Alcala, J.; Eom, C. B.; Catalan, G.; Gruverman, A.

    2012-04-01

    Ferroelectric materials are characterized by a permanent electric dipole that can be reversed through the application of an external voltage, but a strong intrinsic coupling between polarization and deformation also causes all ferroelectrics to be piezoelectric, leading to applications in sensors and high-displacement actuators. A less explored property is flexoelectricity, the coupling between polarization and a strain gradient. We demonstrate that the stress gradient generated by the tip of an atomic force microscope can mechanically switch the polarization in the nanoscale volume of a ferroelectric film. Pure mechanical force can therefore be used as a dynamic tool for polarization control and may enable applications in which memory bits are written mechanically and read electrically.

  15. Modeling optical and UV polarization of AGNs. IV. Polarization timing

    Science.gov (United States)

    Rojas Lobos, P. A.; Goosmann, R. W.; Marin, F.; Savić, D.

    2018-03-01

    Context. Optical observations cannot resolve the structure of active galactic nuclei (AGN), and a unified model for AGN was inferred mostly from indirect methods, such as spectroscopy and variability studies. Optical reverberation mapping allowed us to constrain the spatial dimension of the broad emission line region and thereby to measure the mass of supermassive black holes. Recently, reverberation was also applied to the polarized signal emerging from different AGN components. In principle, this should allow us to measure the spatial dimensions of the sub-parsec reprocessing media. Aim. We conduct numerical modeling of polarization reverberation and provide theoretical predictions for the polarization time lag induced by different AGN components. The model parameters are adjusted to the observational appearance of the Seyfert 1 galaxy NGC 4151. Methods: We modeled scattering-induced polarization and tested different geometries for the circumnuclear dust component. Our tests included the effects of clumpiness and different dust prescriptions. To further extend the model, we also explored the effects of additional ionized winds stretched along the polar direction, and of an equatorial scattering ring that is responsible for the polarization angle observed in pole-on AGN. The simulations were run using a time-dependent version of the STOKES code. Results: Our modeling confirms the previously found polarization characteristics as a function of the observer`s viewing angle. When the dust adopts a flared-disk geometry, the lags reveal a clear difference between type 1 and type 2 AGN. This distinction is less clear for a torus geometry where the time lag is more sensitive to the geometry and optical depth of the inner surface layers of the funnel. The presence of a scattering equatorial ring and ionized outflows increased the recorded polarization time lags, and the polar outflows smooths out dependence on viewing angle, especially for the higher optical depth of the

  16. Platform development: implications for portfolio management

    DEFF Research Database (Denmark)

    Hsuan, Juliana; Hansen, Poul H. Kyvsgård

    2007-01-01

    " The challenge of implementing industrial platforms in practice can be described as a configuration problem caused by a considerable number of variables, which often have contradictory influences on the total performance of the firm. Consequently, the specific platform decisions become extremely...... a framework, based on the portfolio management thinking to evaluate the degree of modularity embedded in a given platform and to which extent it is aligned with other platforms."...

  17. Solid Polarized Targets and Applications

    International Nuclear Information System (INIS)

    Crabb, D. G.

    2008-01-01

    Examples are given of dynamically polarized targets in use today and how the subsystems have changed to meet the needs of todays experiments. Particular emphasis is placed on target materials such as ammonia and lithium deuteride. Recent polarization studies of irradiated materials such as butanol, deuterated butanol, polyethylene, and deuterated polyethylene are presented. The operation of two non-DNP target systems as well as applications of traditional DNP targets are briefly discussed

  18. Artificial anisotropy and polarizing filters.

    Science.gov (United States)

    Flory, François; Escoubas, Ludovic; Lazaridès, Basile

    2002-06-01

    The calculated spectral transmittance of a multilayer laser mirror is used to determine the effective index of the single layer equivalent to the multilayer stack. We measure the artificial anisotropy of photoresist thin films whose structure is a one-dimensional, subwavelength grating obtained from interference fringes. The limitation of the theory of the first-order effective index homogenization is discussed. We designed normal-incidence, polarizing coating and a polarization rotator by embedding anisotropic films in simple multilayer structures.

  19. Polarization bremsstrahlung in α decay

    International Nuclear Information System (INIS)

    Amusia, M. Ya.; Zon, B. A.; Kretinin, I. Yu.

    2007-01-01

    A mechanism of formation of electromagnetic radiation that accompanies α decay and is associated with the emission of photons by electrons of atomic shells due to the scattering of α particles by these atoms (polarization bremsstrahlung) is proposed. It is shown that, when the photon energy is no higher than the energy of K electrons of an atom, polarization bremsstrahlung makes a significant contribution to the bremsstrahlung in α decay

  20. Coherent states with elliptical polarization

    OpenAIRE

    Colavita, E.; Hacyan, S.

    2004-01-01

    Coherent states of the two dimensional harmonic oscillator are constructed as superpositions of energy and angular momentum eigenstates. It is shown that these states are Gaussian wave-packets moving along a classical trajectory, with a well defined elliptical polarization. They are coherent correlated states with respect to the usual cartesian position and momentum operators. A set of creation and annihilation operators is defined in polar coordinates, and it is shown that these same states ...