WorldWideScience

Sample records for plutonium valence adjustment

  1. Plutonium valence state distributions

    International Nuclear Information System (INIS)

    Silver, G.L.

    1974-01-01

    A calculational method for ascertaining equilibrium valence state distributions of plutonium in acid solutions as a function of the plutonium oxidation number and the solution acidity is illustrated with an example. The method may be more practical for manual use than methods based upon polynomial equations. (T.G.)

  2. Determination of plutonium in environmental samples by controlled valence in anion exchange

    International Nuclear Information System (INIS)

    Chen Qingjiang, Yu Yixuan; Nies, H.; Aarkorg, A.; Nielsen, S.P.; Dahlgaard, H.; Mandrup, K.

    1993-01-01

    The title method was successfully used for collecting 239,240 Pu from 200 litres of seawater by coprecipitation with 16 g FeSO 4 *7H 2 O under reducing conditions without filtering. The plutonium is leached by concentrated HNO 3 +HCl from the coprecipitate and solid particles. The precipitate is heated at 400 deg C and digested in aqua regia. Na 2 SO 3 and NaNO 2 have been applied to obtain Pu 4+ valence state in 0.5-1N HNO 3 for different samples. Plutonium and thorium are coadsorbed on anionic resin from 8N HNO 3 . The column is eluted with 8N HNO 3 containing fresh NaO 2 to keep the Pu 4 '+ state for uranium decontamination. The system of the column is changed from 8N HNO 3 to concentrated HCl with 50 ml concentrated HCl containing a few milligrams of NaNO 2 . Further decontamination of thorium was achieved by elution with concentrated HCl instead of 9N HCl. The plutonium is successfully stripped by H 2 O, NaOH, 2N HNO 3 and 0.5 N HNO 3 containing 0.01M NaNO 3 . The chemical yield of plutonium for a 200 l seawater sample is 60-80%. The resolution of the electroplated thin source is very good. (author) 2 refs.; 1 fig.; 6 tabs

  3. Automation of plutonium spectrophotometry

    International Nuclear Information System (INIS)

    Perez, J.J.; Boisde, G.; Goujon de Beauvivier, M.; Chevalier, G.; Isaac, M.

    1980-01-01

    Instrumentation was designed and constructed for automatic control of plutonium by molecular absorption spectrophotometry, on behalf of the reprocessing facilities, to meet two objectives: on-line measurement, of the valency state of plutonium, on by-pass, with the measured concentration covering the process concentration range up to a few mg.l -1 ; laboratory measurement of plutonium adjusted to valency VI, with operation carried out using a preparative system meeting the required containment specifications. For this two objectives, the photometer, optical cell connections are made by optical fibers resistant to β, γ radiation. Except this characteristic the devices are different according to the quality required for result [fr

  4. Determination of plutonium in environmental samples by controlled valence in anion exchange

    DEFF Research Database (Denmark)

    Chen, Q.J.; Aarkrog, A.; Nielsen, S.P.

    1993-01-01

    The title method was successfully used for collecting Pu-239, Pu-249 from 200 litres of seawater by coprecipitation with 16 g FeSO4 . 7H2O under reducing conditions without filtering. The plutonium is leached by concentrated HNO3 + HCI from the coprecipitate and the solid particles. The precipita...... stripped by H20, NaOH, 2N HNO3 and 0.5N HNO3 containing 0.01M NaNO3. The chemical yield of plutonium for a 200 l seawater sample is 60-80%. The resolution of the electroplated thin source is very good....

  5. Gastrointestinal absorption of large amounts of plutonium. Effect of valency state on transfer

    International Nuclear Information System (INIS)

    Lataillade, G.; Duserre, C.; Metivier, H.; Madic, C.; CEA Centre d'Etudes Nucleaires de Fontenay-aux-Roses, 92

    1989-01-01

    The gastrointestinal absorption of Pu, ingested in valency state III, IV, V or VI was studied in baboons. For each state, the absorption of Pu from masses ranging from 1 to 7 mg per kg of body weight was compared with that from masses ranging from 5 to 45 μg per kg of body weight. The mass ingested did not affect the gastrointestinal absorption of Pu(IV) or PU(VI), but for Pu(V) and to a lesser extent Pu(III), absorption clearly increased about 150-fold and 7-fold respectively, when large masses of Pu were ingested. When small masses were ingested, the valency state did not affect absorption. The increased Pu absorption observed after ingestion of large masses of Pu(V) or (III) might be due to the weak hydrolysis of these valency states. (author)

  6. Phasic valence and arousal do not influence post-conflict adjustments in the Simon task.

    Science.gov (United States)

    Dignath, David; Janczyk, Markus; Eder, Andreas B

    2017-03-01

    According to theoretical accounts of cognitive control, conflict between competing responses is monitored and triggers post conflict behavioural adjustments. Some models proposed that conflict is detected as an affective signal. While the conflict monitoring theory assumed that conflict is registered as a negative valence signal, the adaptation by binding model hypothesized that conflict provides a high arousal signal. The present research induced phasic affect in a Simon task with presentations of pleasant and unpleasant pictures that were high or low in arousal. If conflict is registered as an affective signal, the presentation of a corresponding affective signal should potentiate post conflict adjustments. Results did not support the hypothesis, and Bayesian analyses corroborated the conclusion that phasic affects do not influence post conflict behavioural adjustments in the Simon task. Copyright © 2017 Elsevier B.V. All rights reserved.

  7. Test plan for demonstrating plutonium extraction from 10-L solutions using EIChrom extraction chromatographic resins

    International Nuclear Information System (INIS)

    Barney, G.S.

    1994-01-01

    Corrosive plutonium solutions stored in 10-L containers at the Plutonium Finishing Plant must be treated to convert the plutonium to a safe, solid form for storage and to remove the americium so that radiation exposure can be reduced. Extraction chromatographic resins will be tested for separating plutonium from these solutions in the laboratory. Separation parameters will be developed during the testing for large scale processing of the 10-L solutions and solutions of similar composition. Use of chromatographic resins will allow plutonium separation with minimum of chemical addition to the feed and without the need for plutonium valence adjustment. The separated plutonium will be calcined to plutonium oxide by direct solution calcination

  8. Precipitation of plutonium (III) oxalate and calcination to plutonium oxide

    International Nuclear Information System (INIS)

    Esteban, A.; Orosco, E.H.; Cassaniti, P.; Greco, L.; Adelfang, P.

    1989-01-01

    The plutonium based fuel fabrication requires the conversion of the plutonium nitrate solution from nuclear fuel reprocessing into pure PuO2. The conversion method based on the precipitation of plutonium (III) oxalate and subsequent calcination has been studied in detail. In this procedure, plutonium (III) oxalate is precipitated, at room temperature, by the slow addition of 1M oxalic acid to the feed solution, containing from 5-100 g/l of plutonium in 1M nitric acid. Before precipitation, the plutonium is adjusted to trivalent state by addition of 1M ascorbic acid in the presence of an oxidation inhibitor such as hydrazine. Finally, the precipitate is calcinated at 700 deg C to obtain PuO2. A flowsheet is proposed in this paper including: a) A study about the conditions to adjust the plutonium valence. b) Solubility data of plutonium (III) oxalate and measurements of plutonium losses to the filtrate and wash solution. c) Characterization of the obtained products. Plutonium (III) oxalate has several potential advantages over similar conversion processes. These include: 1) Formation of small particle sizes powder with good pellets fabrication characteristics. 2) The process is rather insensitive to most process variables, except nitric acid concentration. 3) Ambient temperature operations. 4) The losses of plutonium to the filtrate are less than in other conversion processes. (Author) [es

  9. The influence of fasting and valence on the gastrointestinal absorption of plutonium in hamsters and rabbits

    International Nuclear Information System (INIS)

    Stather, J.W.; Harrison, J.D.; Smith, H.; Rodwell, P.; David, A.J.

    1980-01-01

    Plutonium ingested in contaminated food may be complexed to biological ligands in the food materials. Also, it is known that Pu in drinking water can exist as Pu(VI). A suggestion has been made, based on the results obtained by Weeks et al (Radiation Res., Vol. 4, 339,1956) that ingestion of Pu(VI) could mean that absorption of Pu would be substantially underestimated by using the value recommended by the ICRP. To further investigate the effect on absorption of both the oxidation state of ingested Pu and the nutritional state of the animal, Pu(IV) and Pu(VI) were administered to normally fed and fasted hamsters. The absorption of Pu(IV) was also measured in rabbits. Absorption of Pu in hamsters was not enhanced by prior oxidation to Pu(VI). However, increased absorption of both Pu(IV) and Pu(VI) was obtained in fasted animals. The results do not substantiate the high value for absorption of Pu(VI) obtained by Weeks et al, and support the value of 10sup(-2%) recommended by the ICRP for soluble forms of Pu. (author)

  10. Plutonium

    International Nuclear Information System (INIS)

    Koelzer, W.

    1989-03-01

    This report contains with regard to 'plutonium' statements on chemistry, occurrence and reactions in the environment, handling procedures in the nuclear fuel cycle, radiation protection methods, biokinetics, toxicology and medical treatment to make available reliable data for the public discussion on plutonium especially its use in nuclear power plants and its radiological assessment. (orig.) [de

  11. Plutonium

    International Nuclear Information System (INIS)

    Watson, G.M.

    1976-01-01

    Discovery of the neutron made it easy to create elements which do not exist in nature. One of these is plutonium, and its isotope with mass number 239 has nuclear properties which make it both a good fuel for nuclear power reactors and a good explosive for nuclear weapons. Since it was discovered during a war the latter characteristic was put to use, but it is now evident that use of plutonium in a particular kind of nuclear reactor, the fast breeder reactor, will allow the world's resources of uranium to last for millennia as a major source of energy. Plutonium is very radiotoxic, resembling radium in this respect. Therefore the widespread introduction of fast breeder reactors to meet energy demands can be contemplated only after assurances on two points; that adequate control of the radiological hazard resulting from the handling of very large amounts of plutonium can be guaranteed, and that diversion of plutonium to illicit use can be prevented. The problems exist to a lesser degree already, since all types of nuclear reactor produce some plutonium. Some plutonium has already been dispersed in the environment, the bulk of it from atmospheric tests of nuclear weapons. (author)

  12. Plutonium

    Energy Technology Data Exchange (ETDEWEB)

    Miner, William N

    1964-01-01

    This pamphlet discusses plutonium from discovery to its production, separation, properties, fabrication, handling, and uses, including use as a reactor fuel and use in isotope power generators and neutron sources.

  13. Plutonium

    International Nuclear Information System (INIS)

    Anon.

    1995-01-01

    Plutonium, which was obtained and identified for the first time in 1941 by chemist Glenn Seaborg - through neutron irradiation of uranium 238 - is closely related to the history of nuclear energy. From the very beginning, because of the high radiotoxicity of plutonium, a tremendous amount of research work has been devoted to the study of the biological effects and the consequences on the environment. It can be said that plutonium is presently one of the elements, whose nuclear and physico-chemical characteristics are the best known. The first part of this issue is a survey of the knowledge acquired on the subject, which emphasizes the sanitary effects and transfer into the environment. Then the properties of plutonium related to energy generation are dealt with. Fissionable, like uranium 235, plutonium has proved a high-performance nuclear fuel. Originally used in breeder reactors, it is now being more and more widely recycled in light water reactors, in MOX fuel. Reprocessing, recycling and manufacturing of these new types of fuel, bound of become more and more widespread, are now part of a self-consistent series of operations, whose technical, economical, industrial and strategical aspects are reviewed. (author)

  14. Plutonium

    International Nuclear Information System (INIS)

    Mueller-Christiansen, K.; Wollesen, M.

    1979-01-01

    As emotions and fear of plutonium are neither useful for the non-professionals nor for the political decision makers and the advantages and disadvantages of plutonium can only put against each other under difficulties, the paper wants to present the most essential scientific data of plutonium in a generally understandable way. Each of the individual sections is concluded and they try to give an answer to the most discussed questions. In order to make understanding easier, the scientific facts are only brought at points where it cannot be done without for the correctness of the presentation. Many details were left out knowingly. On the other hand, important details are dealt with several times if it seems necessary for making the presentation correct. The graphical presentations and the figures in many cases contain more than said in the text. They give the interested reader hints to scientific-technical coherences. The total material is to enable the reader to form his own opinion on plutonium problems which are being discussed in public. (orig./HP) [de

  15. The controlled-potential coulometric determination of plutonium based upon cerium oxidation and the Pu022+/Pu4+ valency change

    International Nuclear Information System (INIS)

    Phillips, G.; Crossley, D.; Venkataramana, P.

    1977-09-01

    Conditions have been established enabling plutonium to be oxidised quantitatively to the hexavalent state in the working compartment of a controlled-potential coulometric cell using electrogenerated ceric ion or excess ceric nitrate. The excess ceric ion is reduced in situ electrochemically without reduction of the hexavalent plutonium. The plutonium is then determined controlled-potential coulometrically by reduction to Pu 3+ followed by oxidation to Pu 4+ . The first oxidation step is conducted in molar nitric acid solution containing sulphamic acid but the coulometric determination step is conducted in molar sulphuric acid solution. The results obtained in the coulometric determination step were less satisfactory following oxidation with electrogenerated ceric ion rather than with chemically added ceric nitrate. Using the recommended conditions, 6 mg quantities of plutonium can be determined with an accuracy of 100.06% and a precision of 0.12% (coefficient of variation). The behaviour of chromium, manganese and vanadium impurity is reported. (author)

  16. SEPARATION OF PLUTONIUM

    Science.gov (United States)

    Maddock, A.G.; Smith, F.

    1959-08-25

    A method is described for separating plutonium from uranium and fission products by treating a nitrate solution of fission products, uranium, and hexavalent plutonium with a relatively water-insoluble fluoride to adsorb fission products on the fluoride, treating the residual solution with a reducing agent for plutonium to reduce its valence to four and less, treating the reduced plutonium solution with a relatively insoluble fluoride to adsorb the plutonium on the fluoride, removing the solution, and subsequently treating the fluoride with its adsorbed plutonium with a concentrated aqueous solution of at least one of a group consisting of aluminum nitrate, ferric nitrate, and manganous nitrate to remove the plutonium from the fluoride.

  17. Adjustment of valence state of Pu and Np in nitric solution containing N,N-dimethylhydroxylamine and monomethylhydrazine by electrolysis

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, H.; Ye, G.A.; Cong, H.F. [China Institute of Atomic Energy, Beijing (China)] [and others

    2012-07-01

    A study of the electrochemical behaviors of N,N-dimethylhydroxylamine (DMHAN) and monomethyl hydrazine (MMH) in nitric acid solution on Pt electrodes were carried out by cyclic voltammetry (CV) and linear sweep voltammetry (LSV) methods. The diffusion coefficients of DMHAN and MMH were obtained by CV. The values are found to be 0.53 x 10{sup -6}6 cm{sup 2}/s D{sub (DMHAN)} and 0.88 x 10{sup -5} cm{sup 2}/s D{sub (MMH)}. The equilibrium potentials (+0.47 V vs. SCE for DMHAN and +0.31 V vs. SCE for MMH) were also measured using Tafel curves. Various valence states of Pu and Np in HNO{sub 3} solution containing DMHAN and MMH in the electrolytic process were investigated by an electrolytic cell using a platinum as the anode and a titanium plate as the cathode. In this procedure, MMH was first electro-oxidized on the Pt anode and Np(V) was reduced to Np(IV) on the Ti cathode. After MMH was entirely consumed, the accumulation of HNO{sub 2} (due to the electrochemical reduction of nitric acid on the Ti cathode) caused a significantly fast catalytic reaction of DMHAN with HNO{sub 3} to form HNO{sub 2}. HNO{sub 2} can oxidize Pu(III) to Pu(IV) quickly. As a result, both oxidation states of Pu and Np were found to be tetravalent in the post-electrolysis solution. A convenient method to keep the post-electrolysis solution at 70 C was used to adjust the oxidation state of Np in it's pentavalent state while retaining the tetravalent state of Pu. This study developed an electrolytic process for the preparation of 2AF feed (the feed of Pu purification cycle) in APOR (Advanced Purex Process Based on Organic Reductants) process by electrochemically oxidizing Pu(III) and selectively adjusting the valence state of neptunium to either Np(IV) or Np(V). (orig.)

  18. Cation exchange process for recovery of plutonium from laboratory solutions containing chloride

    International Nuclear Information System (INIS)

    Gray, L.W.

    1978-10-01

    A cation exchange technique was developed for the separation of plutonium from laboratory solutions containing either Pu(III) or Pu(III)--Pu(IV) mixtures in acidic solutions containing chloride ions. The procedure consists of adjusting the acid concentration to less than one molar and adjusting the valence of the plutonium ion to the (III) state, if necessary. The adjusted solution is fed to a cation exchange column and washed with distilled water to remove residual chlorides from the column. Plutonium is then eluted from the column with 5M nitric acid containing 0.34M sulfamic acid. This procedure was used to separate plutonium from 1.2M chloride solution on a production-scale column. Typical plutonium recovery was 99.97%, while greater than 96% of the original chloride was rejected

  19. Stop plutonium; Stop plutonium

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2003-02-01

    This press document aims to inform the public on the hazards bound to the plutonium exploitation in France and especially the plutonium transport. The first part is a technical presentation of the plutonium and the MOX (Mixed Oxide Fuel). The second part presents the installation of the plutonium industry in France. The third part is devoted to the plutonium convoys safety. The highlight is done on the problem of the leak of ''secret'' of such transports. (A.L.B.)

  20. Potentiometric titration of plutonium

    International Nuclear Information System (INIS)

    Silver, G.L.

    1978-01-01

    In the potentiometric titration of plutonium(III), it has been customary to take the equivalence point as the inflection point on a plot of potential vs. volume of titrant. It have not been, however, demonstrated, that the stoichiometric end point corresponds to the inflection point. Suggestions are made according to which these points may not correspond in the potentiometric titration of plutonium(III), as these titrations are ordinarily concluded in a period of time which is short compared to the time required for valence state rearrangement through disproportionation. (T.G.)

  1. Distribution coefficient of plutonium between sediment and seawater

    International Nuclear Information System (INIS)

    Duursma, E.K.; Parsi, P.

    1974-01-01

    Using plutonium 237 as a tracer, a series of experiments were conducted to determine the distribution coefficient of plutonium onto sediments both under oxic and anoxic conditions, where the plutonium was added to seawater in three different valence states: III, IV and VI

  2. Plutonium fires; Incendies de plutonium

    Energy Technology Data Exchange (ETDEWEB)

    Mestre, E.

    1959-06-23

    The author reports an information survey on accidents which occurred when handling plutonium. He first addresses accidents reported in documents. He indicates the circumstances and consequences of these accidents (explosion in glove boxes, fires of plutonium chips, plutonium fire followed by filter destruction, explosion during plutonium chip dissolution followed by chip fire). He describes hazards associated with plutonium fires: atmosphere and surface contamination, criticality. The author gives some advices to avoid plutonium fires. These advices concern electric installations, the use of flammable solvents, general cautions associated with plutonium handling, venting and filtration. He finally describes how to fight plutonium fires, and measures to be taken after the fire (staff contamination control, atmosphere control)

  3. Uncertainty propagation for the coulometric measurement of the plutonium concentration in CRM126 solution provided by JAEA

    Energy Technology Data Exchange (ETDEWEB)

    Morales-Arteaga, Maria [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2017-11-07

    This GUM WorkbenchTM propagation of uncertainty is for the coulometric measurement of the plutonium concentration in a Pu standard material (C126) supplied as individual aliquots that were prepared by mass. The C126 solution had been prepared and as aliquoted as standard material. Samples are aliquoted into glass vials and heated to dryness for distribution as dried nitrate. The individual plutonium aliquots were not separated chemically or otherwise purified prior to measurement by coulometry in the F/H Laboratory. Hydrogen peroxide was used for valence adjustment.

  4. Stop plutonium

    International Nuclear Information System (INIS)

    2003-02-01

    This press document aims to inform the public on the hazards bound to the plutonium exploitation in France and especially the plutonium transport. The first part is a technical presentation of the plutonium and the MOX (Mixed Oxide Fuel). The second part presents the installation of the plutonium industry in France. The third part is devoted to the plutonium convoys safety. The highlight is done on the problem of the leak of ''secret'' of such transports. (A.L.B.)

  5. The extraction of plutonium with triethylene glycol dichloride

    International Nuclear Information System (INIS)

    Aikin, A.M.; Moss, M.; Bruce, T.

    1951-03-01

    The extraction of plutonium by triethylene glycol dichloride (trigly) has been investigated briefly. The effect of (1) the valence state of the plutonium, (2) the concentration of nitric acid, (3) the concentration of ammonium nitrate and (4) the conditioning of the trigly was measured. The solubility of plutonium IV in trigly was found to be 70 mgms/ml. Solutions of plutonium in trigly and in concentrated nitric acid solutions have been examined spectrophotometrically. (author)

  6. The extraction of plutonium with triethylene glycol dichloride

    Energy Technology Data Exchange (ETDEWEB)

    Aikin, A M; Moss, M; Bruce, T

    1951-03-15

    The extraction of plutonium by triethylene glycol dichloride (trigly) has been investigated briefly. The effect of (1) the valence state of the plutonium, (2) the concentration of nitric acid, (3) the concentration of ammonium nitrate and (4) the conditioning of the trigly was measured. The solubility of plutonium IV in trigly was found to be 70 mgms/ml. Solutions of plutonium in trigly and in concentrated nitric acid solutions have been examined spectrophotometrically. (author)

  7. Uncertainty propagation for the coulometric measurement of the plutonium concentration in MOX-PU4.

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2017-11-07

    This GUM WorkbenchTM propagation of uncertainty is for the coulometric measurement of the plutonium concentration in a Pu standard material (C126) supplied as individual aliquots that were prepared by mass. The C126 solution had been prepared and as aliquoted as standard material. Samples are aliquoted into glass vials and heated to dryness for distribution as dried nitrate. The individual plutonium aliquots were not separated chemically or otherwise purified prior to measurement by coulometry in the F/H Laboratory. Hydrogen peroxide was used for valence adjustment. The Pu assay measurement results were corrected for the interference from trace iron in the solution measured for assay. Aliquot mass measurements were corrected for air buoyancy. The relative atomic mass (atomic weight) of the plutonium from X126 certoficate was used. The isotopic composition was determined by thermal ionization mass spectrometry (TIMS) for comparison but not used in calculations.

  8. Determination of low level of plutonium and uranium isotopes in safeguard swipe sample

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Myung Ho; Park, Jong Ho; Oh, Seong Yong; Lee, Chang Heon; Ahn, Hong Ju; Song, Kyu Seok [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2011-10-15

    For the determination of radionuclides, the separation techniques based on the principles of anion exchange, liquid-liquid extraction or column extraction chromatography are frequently used in nuclear analytical applications. Recently, a novel extraction chromatographic resin has been developed by Horwitz and co-workers, which are capable of selective extraction of the actinides. General separation of plutonium and uranium with extraction chromatographic techniques are focused on the environmental or radioactive waste samples. Also, the chemical yields for Pu and U isotopes with extraction chromatographic method sometimes are variable. For effective extraction of Pu isotopes in the very level of plutonium sample with UTEVA resin, the valence adjustment of Pu isotopes in the sample solution requires due to unstability in the oxidation state of Pu isotopes during separation step. Therefore, it is necessary to develop a simple and robust radiochemical separation method for nano- or pico gram amounts of uranium and plutonium in safeguard swipe samples. Chemical yields of plutonium and uranium with extraction chromatographic method of Pu and U upgrades in this study were compared with several separation methods for Pu and U generally used in the radiochemistry field. Also, the redox reactions of hydrogen peroxide with plutonium in the nitric acid media were investigated by UV-Vis-NIR absorption spectroscopy. Based on general extraction chromatography method with UTEVA resin, the separation method of nano- and picogram amounts of uranium and plutonium in safeguard swipe samples was developed in this study

  9. Measurement and interpretation of plutonium spectra

    International Nuclear Information System (INIS)

    Blaise, J.; Fred, M.S.; Carnall, W.T.; Crosswhite, H.M.; Crosswhite, H.

    1982-01-01

    The atomic spectroscopic data available for plutonium are among the rickest of any in the periodic system. They include high-resolution grating and Fourier-transform spectra as well as extensive Zeeman and isotope-shift studies. We summarize the present status of the term analysis and cite the configurations that have been identified. A least-squares adjustment of a parametric Hamiltonian for configurations of both Pu I and Pu II has shown that almost all of the expected low levels are now known. The use of a model Hamiltonian applicable to both lanthanide and actinide atomic species has been applied to the low configurations of Pu I and Pu II making use of trends predicted by ab initio calculations. This same model has been used to describe the energy levels of Pu 3+ in LaCl 3 , and an extension has permitted preliminary calculations of the spectra of other valence states

  10. Plutonium controversy

    International Nuclear Information System (INIS)

    Richmond, C.R.

    1980-01-01

    The toxicity of plutonium is discussed, particularly in relation to controversies surrounding the setting of radiation protection standards. The sources, amounts of, and exposure pathways of plutonium are given and the public risk estimated

  11. Plutonium controversy

    Energy Technology Data Exchange (ETDEWEB)

    Richmond, C.R.

    1980-01-01

    The toxicity of plutonium is discussed, particularly in relation to controversies surrounding the setting of radiation protection standards. The sources, amounts of, and exposure pathways of plutonium are given and the public risk estimated. (ACR)

  12. Preparation of hexavalent plutonium and its determination in the presence of tetravalent plutonium; Preparation de plutonium hexavalent et dosage en presence de plutonium tetravalent

    Energy Technology Data Exchange (ETDEWEB)

    Corpel, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires; Corpel, J [Institut du Radium, 75 - Paris (France)

    1958-07-01

    In order to study the eventual reduction of plutonium from the VI-valent state to the IV-valent state, in sulphuric medium, under the influence of its own {alpha} radiation or of the {gamma}-rays from a cobalt-60 source, we have developed a method for preparing pure hexavalent plutonium and two methods for determining solutions containing tetravalent and hexavalent plutonium simultaneously. Hexavalent plutonium was prepared by anodic oxidation at a platinum electrode. Study of the oxidation yield as a function of various factors has made it possible to define experimental conditions giving complete oxidation. For concentrations in total plutonium greater than 1.5 x 10{sup -3} M, determination of the two valencies IV and VI was carried out by spectrophotometry at two wavelengths. For lower concentrations, the determination was done by counting, after separation of the tetravalent plutonium in the form of fluoride in the presence of a carrier. (author) [French] Afin d'etudier l'eventuelle reduction du plutonium de l'etat de valence VI a l'etat de valence IV, en milieu sulfurique sous l'influence de son propre rayonnement {alpha} ou des rayons {gamma} d'une source de cobalt-60, nous avons mis au point une methode de preparation de plutonium hexavalent pur et deux methodes de dosage des solutions contenant simultanement du plutonium tetravalent et du plutonium hexavalent. Nous avons prepare le plutonium hexavalent par oxydation anodique au contact d'une electrode de platine. L'etude de rendement de l'oxydation en fonction des divers facteurs nous a permis de definir des conditions experimentales donnant une oxydation complete. Pour des concentrations en plutonium total superieures a 1,5.10{sup -3} M, le dosage des deux valences IV et VI a ete realise par spectrophotometrie a deux longueurs d'onde. Pour des concentrations inferieures, le dosage a ete effectue par comptage apres separation du plutonium tetravalent sous la forme du fluorure en presence d'un entraineur

  13. Continuous precipitation process of plutonium salts

    International Nuclear Information System (INIS)

    Richard, P.

    1967-03-01

    This work concerns the continuous precipitation process of plutonium oxalate. Investigations about the solubility of different valence states in nitric-oxalic and in nitric-sulfuric-oxalic medium lead to select the precipitation process of tetravalent plutonium oxalate. Settling velocity and granulometry of tetravalent oxalate plutonium have been studied with variation of several precipitation parameters such as: temperature, acidity, excess of oxalic acid and aging time. Then are given test results of some laboratory continuous apparatus. Conditions of operation with adopted tubular apparatus are defined in conclusion. A flow-sheet is given for a process at industrial scale. (author) [fr

  14. Levels of valence

    Directory of Open Access Journals (Sweden)

    Vera eShuman

    2013-05-01

    Full Text Available The distinction between the positive and the negative is fundamental in our emotional life. In appraisal theories, in particular in the component process model of emotion (Scherer, 1984, 2010, qualitatively different types of valence are proposed based on appraisals of (unpleasantness, goal obstructiveness/conduciveness, low or high power, self- (incongruence, and moral badness/goodness. This multifaceted conceptualization of valence is highly compatible with the frequent observation of mixed feelings in real life. However, it seems to contradict the one-dimensional conceptualization of valence often encountered in psychological theories, and the notion of valence as a common currency used to explain choice behavior. Here, we propose a framework to integrate the seemingly disparate conceptualizations of multifaceted valence and one-dimensional valence by suggesting that valence should be conceived at different levels, micro and macro. Micro-valences correspond to qualitatively different types of evaluations, potentially resulting in mixed feelings, whereas one-dimensional macro-valence corresponds to an integrative common currency to compare alternatives for choices. We propose that conceptualizing levels of valence may focus research attention on the mechanisms that relate valence at one level (micro to valence at another level (macro, leading to new hypotheses and addressing various concerns that have been raised about the valence concept, such as the valence-emotion relation.

  15. Levels of Valence

    Science.gov (United States)

    Shuman, Vera; Sander, David; Scherer, Klaus R.

    2013-01-01

    The distinction between the positive and the negative is fundamental in our emotional life. In appraisal theories, in particular in the component process model of emotion (Scherer, 1984, 2010), qualitatively different types of valence are proposed based on appraisals of (un)pleasantness, goal obstructiveness/conduciveness, low or high power, self-(in)congruence, and moral badness/goodness. This multifaceted conceptualization of valence is highly compatible with the frequent observation of mixed feelings in real life. However, it seems to contradict the one-dimensional conceptualization of valence often encountered in psychological theories, and the notion of valence as a common currency used to explain choice behavior. Here, we propose a framework to integrate the seemingly disparate conceptualizations of multifaceted valence and one-dimensional valence by suggesting that valence should be conceived at different levels, micro and macro. Micro-valences correspond to qualitatively different types of evaluations, potentially resulting in mixed feelings, whereas one-dimensional macro-valence corresponds to an integrative “common currency” to compare alternatives for choices. We propose that conceptualizing levels of valence may focus research attention on the mechanisms that relate valence at one level (micro) to valence at another level (macro), leading to new hypotheses, and addressing various concerns that have been raised about the valence concept, such as the valence-emotion relation. PMID:23717292

  16. Plutonium controversy

    International Nuclear Information System (INIS)

    Gofman, J.W.

    1976-01-01

    If the world chooses to seek a solution to the energy dilemma through nuclear energy, the element plutonium will become an article of commerce to be handled in quantities of thousands of tonnes annually. Plutonium is a uniquely potent inhalation carcinogen, the potential induction of lung cancer dwarfing other possible toxic effects. For reasons to be presented here, it is the author's opinion that plutonium's carcinogenicity has been very seriously underestimated. If one couples the corrected carcinogenicity with the probable degree of industrial containment of the plutonium, it appears that the commercialization of a plutonium-based energy economy is not an acceptable option for society. Sagan's statement that ''the experience of 30 years supports the contention that plutonium can be used safely'' is manifestly indefensible. No meaningful epidemiological study of plutonium-exposed workers for that 30-year period has ever been done. Since thousands of those possibly exposed have left the industry and are not even available to follow-up, it is doubtful that any meaningful study of ''the experience of 30 years'' will ever be accomplished

  17. Valencies of the lanthanides

    OpenAIRE

    Johnson, David A.; Nelson, Peter G.

    2018-01-01

    The valencies of the lanthanides vary more than was once thought. In addition to valencies associated with a half-full shell, there are valencies associated with a quarter- and three-quarter-full shell. This can be explained on the basis of Slater’s theory of many-electron atoms. The same theory explains the variation in complexing constants in the trivalent state (the “tetrad effect”). Valency in metallic and organometallic compounds is also discussed.

  18. Plutonium solubilities

    International Nuclear Information System (INIS)

    Puigdomnech, I.; Bruno, J.

    1991-02-01

    Thermochemical data has been selected for plutonium oxide, hydroxide, carbonate and phosphate equilibria. Equilibrium constants have been evaluated in the temperature range 0 to 300 degrees C at a pressure of 1 bar to T≤100 degrees C and at the steam saturated pressure at higher temperatures. Measured solubilities of plutonium that are reported in the literature for laboratory experiments have been collected. Solubility data on oxides, hydroxides, carbonates and phosphates have been selected. No solubility data were found at temperatures higher than 60 degrees C. The literature solubility data have been compared with plutonium solubilities calculated with the EQ3/6 geochemical modelling programs, using the selected thermodynamic data for plutonium. (authors)

  19. Zirconolite glass-ceramics for plutonium immobilization: The effects of processing redox conditions on charge compensation and durability

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Yingjie, E-mail: yzx@ansto.gov.au; Gregg, Daniel J.; Kong, Linggen; Jovanovich, Miodrag; Triani, Gerry

    2017-07-15

    Zirconolite glass-ceramic samples doped with plutonium have been prepared via hot isostatic pressing. The effects of processing redox and plutonium loadings on plutonium valences, the presence of cation vacancies, zirconolite phase compositions, microstructures and durability have been investigated. Either tetravalent or trivalent plutonium ions may be incorporated on the Ca-site of CaZrTi{sub 2}O{sub 7} zirconolite with the Ca-site cation vacancies and the incorporation of Al{sup 3+} ions on the Ti-site for charge compensation. Plutonium and gadolinium (as a neutron absorber) are predominantly partitioned in zirconolite phases leading to the formation of chemically durable glass-ceramics suitable for the immobilization of impure plutonium wastes arising from the nuclear fuel cycle. - Highlights: •Plutonium validations of zirconolite glass-ceramics. •Effects of processing redox and plutonium loading. •Zirconolite phase compositions and plutonium valences. •Cation vacancies and chemical durability.

  20. Plutonium decontamination studies using Reverse Osmosis

    International Nuclear Information System (INIS)

    Plock, C.E.; Travis, T.N.

    1980-01-01

    Water in batches of 45 gallons each, from a creek crossing the Rocky Flats Plant, was transferred to the Reverse Osmosis (RO) laboratory for experimental testing. The testing involved using RO for plutonium decontamination. For each test, the water was spiked with plutonium, had its pH adjusted, and was then processed by RO. At a water recovery level of 87%, the plutonium decontamination factors ranged from near 100 to 1200, depending on the pH of the processed water

  1. CONVERSION OF PLUTONIUM TRIFLUORIDE TO PLUTONIUM TETRAFLUORIDE

    Science.gov (United States)

    Fried, S.; Davidson, N.R.

    1957-09-10

    A large proportion of the trifluoride of plutonium can be converted, in the absence of hydrogen fluoride, to the tetrafiuoride of plutonium. This is done by heating plutonium trifluoride with oxygen at temperatures between 250 and 900 deg C. The trifiuoride of plutonium reacts with oxygen to form plutonium tetrafluoride and plutonium oxide, in a ratio of about 3 to 1. In the presence of moisture, plutonium tetrafluoride tends to hydrolyze at elevated temperatures and therefore it is desirable to have the process take place under anhydrous conditions.

  2. Plutonium (Pu)

    International Nuclear Information System (INIS)

    2002-01-01

    This pedagogical document presents the properties and uses of plutonium: where does it come from, the history of its discovery, its uses and energy content, its recycling and reuse in MOX fuels, its half-life, toxicity and presence in the environment. (J.S.)

  3. Continuous precipitation process of plutonium salts; Procede continu de precipitation des sels de plutonium

    Energy Technology Data Exchange (ETDEWEB)

    Richard, P [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

    1967-03-01

    This work concerns the continuous precipitation process of plutonium oxalate. Investigations about the solubility of different valence states in nitric-oxalic and in nitric-sulfuric-oxalic medium lead to select the precipitation process of tetravalent plutonium oxalate. Settling velocity and granulometry of tetravalent oxalate plutonium have been studied with variation of several precipitation parameters such as: temperature, acidity, excess of oxalic acid and aging time. Then are given test results of some laboratory continuous apparatus. Conditions of operation with adopted tubular apparatus are defined in conclusion. A flow-sheet is given for a process at industrial scale. (author) [French] Cette etude porte sur la precipitation continue de l'oxalate de plutonium. L'etude de la solubilite des differentes valences du plutonium dans des milieux acides nitrique-oxalique, puis nitrique-sulfurique-oxalique conduit a choisir la precipitation de l'oxalate de plutonium tetravalent. L'etude porte ensuite sur la sedimentation et la granulometrie de l'oxalate de Pu{sup 4+} obtenue en faisant varier differents parametres de la precipitation : la temperature, l'acidite, l'exces oxalique et le temps de murissement. La derniere partie traite des resultats obtenus avec plusieurs types d'appareils continus essayes au laboratoire. En conclusion sont donnees les conditions de marche de l'appareil tubulaire adopte, ainsi qu'une extrapolation a l'echelle industrielle sous forme d'un flow-sheet. (auteur)

  4. Learning more about plutonium

    International Nuclear Information System (INIS)

    2005-01-01

    This document offers chemical, metallurgical and economical information on the plutonium, a hard white radioelement. It deals also on the plutonium formation in the earth, the plutonium use in the nuclear industry, the plutonium in the environment and the plutonium toxicity. (A.L.B.)

  5. Plutonium in nature

    International Nuclear Information System (INIS)

    Madic, C.

    1994-01-01

    Plutonium in nature comes from natural sources and anthropogenic ones. Plutonium at the earth surface comes principally from anthropogenic sources. It is easily detectable in environment. The plutonium behaviour in environment is complex. It seems necessary for the future to reduce releases in environment, to improve predictive models of plutonium behaviour in geosphere, to precise biological impact of anthropogenic plutonium releases

  6. Phenomenology of uranium-plutonium homogenization in nuclear fuels

    International Nuclear Information System (INIS)

    Marin, J.M.

    1988-01-01

    The uranium and plutonium cations distribution in mixed oxide fuels (U 1-y Pu y )O 2 with y ≤ 0.1 has been studied in laboratory with industrial fabrication methods. Our experiences has showed a slow cations migration. In the substoichiometry (UPu)O 2-x the diffusion is in connection with the plutonium valence which is an indicator of the oxidoreduction state of the crystal lattice. The plutonium valence is in connection with the oxygen ion deficit in order to compensate the electrical charge. The oxygen ratio of the solid depends of the oxygen partial pressure prevailing at the time of product elaboration but it can be modified by impurities. These impurities permit to increase or decrease the fuel characteristics and performances. An homogeneity analysis methodology is proposed, its objective is to classify the mixed oxide fuels according to the uranium and plutonium ions distribution [fr

  7. Plutonium uniqueness

    International Nuclear Information System (INIS)

    Silver, G.L.

    1984-01-01

    A standard is suggested against which the putative uniqueness of plutonium may be tested. It is common folklore that plutonium is unique among the chemical elements because its four common oxidation states can coexist in the same solution. Whether this putative uniqueness appears only during transit to equilibrium, or only at equilibrium, or all of the time, is not generally made clear. But while the folklore may contain some truth, it cannot be put to test until some measure of 'uniqueness' is agreed upon so that quantitative comparisons are possible. One way of measuring uniqueness is as the magnitude of the product of the mole fractions of the element at equilibrium. A 'coexistence index' is defined and discussed. (author)

  8. Plutonium story

    International Nuclear Information System (INIS)

    Seaborg, G.T.

    1981-09-01

    The first nuclear synthesis and identification (i.e., the discovery) of the synthetic transuranium element plutonium (isotope 238 Pu) and the demonstration of its fissionability with slow neutrons (isotope 239 Pu) took place at the University of California, Berkeley, through the use of the 60-inch and 37-inch cyclotrons, in late 1940 and early 1941. This led to the development of industrial scale methods in secret work centered at the University of Chicago's Metallurgical Laboratory and the application of these methods to industrial scale production, at manufacturing plants in Tennessee and Washington, during the World War II years 1942 to 1945. The chemical properties of plutonium, needed to devise the procedures for its industrial scale production, were studied by tracer and ultramicrochemical methods during this period on an extraordinarily urgent basis. This work, and subsequent investigations on a worldwide basis, have made the properties of plutonium very well known. Its well studied electronic structure and chemical properties give it a very interesting position in the actinide series of inner transition elements

  9. A rapid method of dosing plutonium in radioactive effluents; Methode de dosage rapide du plutonium dans les effluents radioactifs (1961)

    Energy Technology Data Exchange (ETDEWEB)

    Scheidhauer, J; Messainguiral, L [Commissariat a l' Energie Atomique, Centre de Production de Plutonium, Marcoule (France). Centre d' Etudes Nucleaires

    1961-07-01

    The plutonium is first separated by a lanthanum fluoride precipitation. The precipitated fluorides are dissolved in normal nitric acid solution in the presence of aluminium nitrate. The plutonium transformed to the tetravalent state is then extracted with thenoyltrifluoroacetone and returned to the aqueous phase with 10 N nitric acid. After evaporation on a watch glass the residue is calcined on a Meker burner and counted using a counting system fitted with a zinc sulphide scintillator. When necessary, the calcium is eliminated at the beginning of the dosage by a fluoride precipitation, the plutonium being oxidised to the valency IV. (authors) [French] Le plutonium est d'abord separe par entrainement au fluorure de lanthane. Le precipite des fluorures est remis en solution en milieu acide nitrique normal, en presence de nitrate d'aluminium. Le plutonium amene a la valence IV est alors extrait par la thenoyltrifluoroacetone et remis en phase aqueuse dans l'acide nitrique 10 N. Apres evaporation sur verre de montre, le residu est calcine sur bec Meker et compte sur un ensemble de comptage equipe d'un scintillateur au sulfure de zinc. Lorsque cela est necessaire, le calcium est elimine, au debut du dosage, par precipitation du fluorure, le plutonium etant oxyde a la valence VI. (auteurs)

  10. PRODUCTION OF PLUTONIUM METAL

    Science.gov (United States)

    Lyon, W.L.; Moore, R.H.

    1961-01-17

    A process is given for producing plutonium metal by the reduction of plutonium chloride, dissolved in alkali metal chloride plus or minus aluminum chloride, with magnesium or a magnesium-aluminum alloy at between 700 and 800 deg C and separating the plutonium or plutonium-aluminum alloy formed from the salt.

  11. Fuel cycles using adulterated plutonium

    International Nuclear Information System (INIS)

    Brooksbank, R.E.; Bigelow, J.E.; Campbell, D.O.; Kitts, F.G.; Lindauer, R.B.

    1978-01-01

    Adjustments in the U-Pu fuel cycle necessitated by decisions made to improve the nonproliferation objectives of the US are examined. The uranium-based fuel cycle, using bred plutonium to provide the fissile enrichment, is the fuel system with the highest degree of commercial development at the present time. However, because purified plutonium can be used in weapons, this fuel cycle is potentially vulnerable to diversion of that plutonium. It does appear that there are technologically sound ways in which the plutonium might be adulterated by admixture with 238 U and/or radioisotopes, and maintained in that state throughout the fuel cycle, so that the likelihood of a successful diversion is small. Adulteration of the plutonium in this manner would have relatively little effect on the operations of existing or planned reactors. Studies now in progress should show within a year or two whether the less expensive coprocessing scheme would provide adequate protection (coupled perhaps with elaborate conventional safeguards procedures) or if the more expensive spiked fuel cycle is needed as in the proposed civex pocess. If the latter is the case, it will be further necessary to determine the optimum spiking level, which could vary as much as a factor of a billion. A very basic question hangs on these determinations: What is to be the nature of the recycle fuel fabrication facilities. If the hot, fully remote fuel fabrication is required, then a great deal of further development work will be required to make the full cycle fully commercial

  12. Valency and molecular structure

    CERN Document Server

    Cartmell, E

    1977-01-01

    Valency and Molecular Structure, Fourth Edition provides a comprehensive historical background and experimental foundations of theories and methods relating to valency and molecular structures. In this edition, the chapter on Bohr theory has been removed while some sections, such as structures of crystalline solids, have been expanded. Details of structures have also been revised and extended using the best available values for bond lengths and bond angles. Recent developments are mostly noted in the chapter on complex compounds, while a new chapter has been added to serve as an introduction t

  13. Plutonium-239

    International Nuclear Information System (INIS)

    Ammerich, Marc; Frot, Patricia; Gambini, Denis-Jean; Gauron, Christine; Moureaux, Patrick; Herbelet, Gilbert; Lahaye, Thierry; Pihet, Pascal; Rannou, Alain

    2014-06-01

    This sheet belongs to a collection which relates to the use of radionuclides essentially in unsealed sources. Its goal is to gather on a single document the most relevant information as well as the best prevention practices to be implemented. These sheets are made for the persons in charge of radiation protection: users, radioprotection-skill persons, labor physicians. Each sheet treats of: 1 - the radio-physical and biological properties; 2 - the main uses; 3 - the dosimetric parameters; 4 - the measurement; 5 - the protection means; 6 - the areas delimitation and monitoring; 7 - the personnel classification, training and monitoring; 8 - the effluents and wastes; 9 - the authorization and declaration administrative procedures; 10 - the transport; and 11 - the right conduct to adopt in case of incident or accident. This sheet deals specifically with Plutonium-239

  14. The plutonium fuel cycles

    International Nuclear Information System (INIS)

    Pigford, T.H.; Ang, K.P.

    1975-01-01

    The quantities of plutonium and other fuel actinides have been calculated for equilibrium fuel cycles for 1000-MW water reactors fueled with slightly enriched uranium, water reactors fueled with plutonium and natural uranium, fast-breder reactors, gas-cooled reactors fueled with thorium and highly enriched uranium, and gas-cooled reactors fueled with thorium, plutonium and recycled uranium. The radioactivity quantities of plutonium, americium and curium processed yearly in these fuel cycles are greatest for the water reactors fueled with natural uranium and recycled plutonium. The total amount of actinides processed is calculated for the predicted future growth of the U.S. nuclear power industry. For the same total installed nuclear power capacity, the introduction of the plutonium breeder has little effect upon the total amount of plutonium in this century. The estimated amount of plutonium in the low-level process wastes in the plutonium fuel cycles is comparable to the amount of plutonium in the high-level fission product wastes. The amount of plutonium processed in the nuclear fuel cycles can be considerably reduced by using gas-cooled reactors to consume plutonium produced in uranium-fueled water reactors. These, and other reactors dedicated for plutonium utilization, could be co-located with facilities for fuel reprocessing ad fuel fabrication to eliminate the off-site transport of separated plutonium. (author)

  15. Extraction and purification of plutonium by a tertiary amine; Extraction et purification du plutonium par une amine tertiaire

    Energy Technology Data Exchange (ETDEWEB)

    Trentinian, M de; Chesne, A [Commissariat a l' Energie Atomique, Fontenay aux Roses, Section de Chimie des Actimides (France).Centre d' Etudes Nucleaires; Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

    1960-07-01

    Trilaurylamine diluted with a paraffinic solvent (dodecane) was studied as part of the research dealing with the separation and purification of plutonium. The physical properties (solubility of nitrates in the amine as a function of temperature) and the resistance to radiations of this substance were examined. The extraction characteristics of nitric solutions of plutonium, uranium and certain fission products are given as a function of the following factors: concentration of the various ions in solution, valency states. A method of plutonium purification based on these results is presented. (author) [French] La trilaurylamine diluee par un solvant paraffinique (dodecane) a ete etudiee dans le cadre des recherches concernant la separation et la purification du plutonium. Une etude des caracteres physiques (solubilite des nitrates dans l'amine en fonction de la temperature) s'ajoute a celle de la tenue aux radiations de ce corps. Les caracteristiques d'extraction de solutions nitriques de plutonium, uranium, et certains produits de fission, sont donnes en fonction des facteurs suivants: concentration des differents ions en solution, etats de valence. On presente une methode de purification du plutonium basee sur ces resultats. (auteur)

  16. Plutonium economy

    International Nuclear Information System (INIS)

    Traube, K.

    1984-01-01

    The author expresses his opinion on the situation, describes the energy-economic setting, indicates the alternatives: fuel reprocessing or immediate long-term storage, and investigates the prospects for economic utilization of the breeder reactors. All the facts suggest that the breeder reactor will never be able to stand economic competition with light-water reactors. However, there is no way to prove the future. It is naive to think that every doubt could and must be removed before stopping the development of breeder reactors - and thus also the reprocessing of the fuel of light-water reactors. On the basis of the current state of knowledge an unbiased cost-benefit-analysis can only lead to the recommendation to stop construction immediately. But can 'experts', who for years or even decades have called for and supported the development of breeder reactors be expected to make an unbiased analysis. Klaus Traube strikes the balance of the state Germany's nuclear economy is in: although there is no chance of definitively abandoning that energy-political cul-de-sac, no new adventures must be embarked upon. Responsible handling of currently used nuclear technology means to give up breeder technology and waive plutonium economy. It is no supreme technology with the aid of which structural unemployment or any other economic problem could be solved. (orig.) [de

  17. Method to manufacture a nuclear fuel from uranium-plutonium monocarbide or uranium-plutonium mononitride

    International Nuclear Information System (INIS)

    Krauth, A.; Mueller, N.

    1977-01-01

    Pure uranium carbide or nitride is converted with plutonium oxide and carbon (all in powder form) to uranium-plutonium monocarbide or mononitride by cold pressing and sintering at about 1600 0 C. Pure uranium carbide or uranium nitride powder is firstly prepared without extensive safety measures. The pure uranium carbide or nitride powder can also be inactivated by using chemical substances (e.g. stearic acid) and be handled in air. The sinterable uranium carbide or nitride powder (or also granulate) is then introduced into the plutonium line and mixed with a nonstoichiometrically adjusted, prereacted mixture of plutonium oxide and carbon, pressed to pellets and reaction sintered. The surface of the uranium-plutonium carbide (higher metal content) can be nitrated towards the end of the sinter process in a stream of nitrogen. The protective layer stabilizes the carbide against the water and oxygen content in air. (IHOE) [de

  18. Probing phonons in plutonium

    International Nuclear Information System (INIS)

    Wong, Joe; Krisch, M.; Farber, D.; Occelli, F.; Schwartz, A.; Chiang, T.C.; Wall, M.; Boro, C.; Xu, Ruqing

    2010-01-01

    ) capability on ID28. The complete PDCs for an fcc Pu-0.6 wt% Ga alloy are plotted in Figure 2, and represent the first full set of phonon dispersions ever determined for any Pu-bearing materials. The solid curves (red) are calculated using a standard Born-von Karman (B-vK) force constant model. An adequate fit to the experimental data is obtained if interactions up to the fourth-nearest neighbours are included. The dashed curves (blue) are recent dynamical mean field theory (DMFT) results by Dai et al. The elastic moduli calculated from the slopes of the experimental phonon dispersion curves near the Λ point are: C 11 = 35.3 ± 1.4 GPa, C 12 = 25.5 ± 1.5 GPa and C 44 = 30.53 ± 1.1 GPa. These values are in excellent agreement with those of the only other measurement on a similar alloy (1 wt % Ga) using ultrasonic techniques as well as with those recently calculated from a combined DMFT and linear response theory for pure (delta)-Pu. Several unusual features, including a large elastic anisotropy, a small shear elastic modulus C(prime), a Kohn-like anomaly in the T 1 [011] branch, and a pronounced softening of the [111] transverse modes are found. These features can be related to the phase transitions of plutonium and to strong coupling between the lattice structure and the 5f valence instabilities. The HRIXS results also provide a critical test for theoretical treatments of highly correlated 5f electron systems as exemplified by recent dynamical mean field theory (DMFT) calculations for (delta)-plutonium. The experimental-theoretical agreements shown in Figure 2 in terms of a low shear elastic modulus C(prime), a Kohn-like anomaly in the T 1 [011] branch, and a large softening of the T[111] modes give credence to the DMFT approach for the theoretical treatment of 5f electron systems of which (delta)-Pu is a classic example. However, quantitative differences remain. These are the position of the Kohn anomaly along the T 1 [011] branch, the energy maximum of the T[111] mode s

  19. Adjustment of a direct method for the determination of man body burden in Pu-239 on by X-ray detection of U-235; Mise au point d'une methode directe de determination de la charge corporelle en plutonium 239 chez l'homme par detection X de l'uranium 235

    Energy Technology Data Exchange (ETDEWEB)

    Boulay, P [Commissariat a l' Energie Atomique, Bruyeres-le-Chatel (France). Centre d' Etudes

    1968-04-01

    The use of Pu-239 on a larger scale sets a problem about the contamination measurement by aerosol at lung level. A method of direct measurement of Pu-239 lung burden is possible, thanks to the use of a large area window proportional counter. A counter of such pattern, has been especially carried out for this purpose. The adjustment of the apparatus allows an adequate sensibility to detect a contamination at the maximum permissible body burden level. Besides, a method for individual 'internal calibration', with a plutonium mock: the protactinium-233, is reported. (author) [French] L'utilisation a une echelle de plus en plus large du plutonium-239 pose un probleme de la mesure de la contamination par aerosol au niveau du poumon. Une methode de mesure directe de la charge pulmonaire en plutonium-239 est possible grace a l'utilisation d'un compteur proportionnel a fenetre de grande surface. Un compteur de ce type a specialement ete realise dans ce but. La mise au point de l'appareillage permet une sensibilite suffisante pour deceler une contamination au niveau de la Q.M.A (quantite maximale admissible). D'autre part, une methode 'd'etalonnage interne' de l'individu a l'aide d'un simulateur de plutonium, le protactinium-233, est decrite. (auteur)

  20. Plutonium Finishing Plant

    Data.gov (United States)

    Federal Laboratory Consortium — The Plutonium Finishing Plant, also known as PFP, represented the end of the line (the final procedure) associated with plutonium production at Hanford.PFP was also...

  1. Plutonium biokinetics in humans

    International Nuclear Information System (INIS)

    Popplewell, D.; Ham, G.; McCarthy, W.; Lands, C.

    1994-01-01

    By using an 'unusual' isotope it is possible to carry out experiments with plutonium in volunteers at minimal radiation dose levels. Measurements have been made of the gut transfer factor and the urinary excretion of plutonium after intravenous injection. (author)

  2. Plutonium in uranium deposits

    International Nuclear Information System (INIS)

    Curtis, D.; Fabryka-Martin, J.; Aguilar, R.; Attrep, M. Jr.; Roensch, F.

    1992-01-01

    Plutonium-239 (t 1/2 , 24,100 yr) is one of the most persistent radioactive constituents of high-level wastes from nuclear fission power reactors. Effective containment of such a long-lived constituent will rely heavily upon its containment by the geologic environment of a repository. Uranium ore deposits offer a means to evaluate the geochemical properties of plutonium under natural conditions. In this paper, analyses of natural plutonium in several ores are compared to calculated plutonium production rates in order to evaluate the degree of retention of plutonium by the ore. The authors find that current methods for estimating production rates are neither sufficiently accurate nor precise to provide unambiguous measures of plutonium retention. However, alternative methods for evaluating plutonium mobility are being investigated, including its measurement in natural ground waters. Preliminary results are reported and establish the foundation for a comprehensive characterization of plutonium geochemistry in other natural environments

  3. Plutonium metal burning facility

    International Nuclear Information System (INIS)

    Hausburg, D.E.; Leebl, R.G.

    1977-01-01

    A glove-box facility was designed to convert plutonium skull metal or unburned oxide to an oxide acceptable for plutonium recovery and purification. A discussion of the operation, safety aspects, and electrical schematics are included

  4. Plutonium Training Opportunities

    Energy Technology Data Exchange (ETDEWEB)

    Balatsky, Galya Ivanovna [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Wolkov, Benjamin [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2015-03-26

    This report was created to examine the current state of plutonium training in the United States and to discover ways in which to ensure that the next generation of plutonium workers are fully qualified.

  5. Optimization and plutonium equilibrium

    International Nuclear Information System (INIS)

    Silver, G.L.

    1976-01-01

    The sequential simplex method has been used to estimate the extent of disproportionation of tetravalent plutonium in dilute acid. A method for simulating potentiometric titrations is proposed, and this method suggests that the stoichiometric end point and the inflection point may not always correspond in the potentiometric titration of plutonium. A possible characteristic equation for the nitrite-plutonium reaction is illustrated, and the method of proportional equations is extended to the iron-plutonium reaction

  6. Cigarette smoke and plutonium

    International Nuclear Information System (INIS)

    Filipy, R.E.

    1985-01-01

    Autoradiographic techniques with liquid photographic emulsion and cellulose nitrate track-etch film are being used to investigate the spatial distribution of inhaled plutonium in the lungs of beagle dogs exposed to cigarette smoke or to the plutonium aerosol only. More plutonium than expected was detected on the inner surfaces of bronchi, and particles were observed beneath the bronchial mucosa. 2 figures, 2 tables

  7. Optimizing Plutonium stock management

    International Nuclear Information System (INIS)

    Niquil, Y.; Guillot, J.

    1997-01-01

    Plutonium from spent fuel reprocessing is reused in new MOX assemblies. Since plutonium isotopic composition deteriorates with time, it is necessary to optimize plutonium stock management over a long period, to guarantee safe procurement, and contribute to a nuclear fuel cycle policy at the lowest cost. This optimization is provided by the prototype software POMAR

  8. Treatment of plutonium contaminations

    International Nuclear Information System (INIS)

    Lafuma, J.

    1983-01-01

    Three kinds of plutonium contaminations were considered: skin contamination; contaminated wounds; contamination by inhalation. The treatment of these contaminations was studied for insoluble (oxide and metal forms) and soluble plutonium (complexes). The use of DTPA and therapeutic problems encountered with stable plutonium complexes were analyzed. The new possibilities of internal decontamination using Puchel and LICAM were evaluated [fr

  9. Plutonium, nuclear fuel; Le plutonium, combustible nucleaire

    Energy Technology Data Exchange (ETDEWEB)

    Grison, E [Commissariat a l' Energie Atomique, Fontenay aux Roses (France). Centre d' Etudes Nucleaires, Saclay

    1960-07-01

    A review of the physical properties of metallic plutonium, its preparation, and the alloys which it forms with the main nuclear metals. Appreciation of its future as a nuclear fuel. (author) [French] Apercu sur les proprietes physiques du plutonium metallique, sa preparation, ses alliages avec les principaux metaux nucleaires. Consideration sur son avenir en tant que combustible nucleaire. (auteur)

  10. Plutonium economy. Plutonium-Wirtschaft

    Energy Technology Data Exchange (ETDEWEB)

    Traube, K

    1984-01-01

    The author expresses his opinion on the situation, describes the energy-economic setting, indicates the alternatives: fuel reprocessing or immediate long-term storage, and investigates the prospects for economic utilization of the breeder reactors. All the facts suggest that the breeder reactor will never be able to stand economic competition with light-water reactors. However, there is no way to prove the future. It is naive to think that every doubt could and must be removed before stopping the development of breeder reactors - and thus also the reprocessing of the fuel of light-water reactors. On the basis of the current state of knowledge an unbiased cost-benefit-analysis can only lead to the recommendation to stop construction immediately. But can 'experts', who for years or even decades have called for and supported the development of breeder reactors be expected to make an unbiased analysis. Klaus Traube strikes the balance of the state Germany's nuclear economy is in: although there is no chance of definitively abandoning that energy-political cul-de-sac, no new adventures must be embarked upon. Responsible handling of currently used nuclear technology means to give up breeder technology and waive plutonium economy. It is no supreme technology with the aid of which structural unemployment or any other economic problem could be solved.

  11. The plutonium society

    International Nuclear Information System (INIS)

    Mez, L.; Richter, M.

    1981-01-01

    The lectures of an institute are reported on, which took place between 25th and 27th January 1980 in Berlin. The subsequent public panel discussion with representations from the political parties is then documentated in a few press-reports. The themes of the 8 lectures are: views and facts on plutonium, plutonium as an energy resource, military aspects of the production of plutonium, economic aspects of the plutonium economy, the position of the trade unions on the industrial reconversion, the alleged inevitability of a plutonium society and the socio-political alternatives and perspectives of nuclear waste disposal. (UA) [de

  12. The use of plutonium

    International Nuclear Information System (INIS)

    Marshall, W.

    1980-01-01

    The use of plutonium as a vital energy source producing maximum economic benefit with minimum proliferation risks is discussed. Having considered the production of plutonium, several possible plutonium fuel cycle options are identified and the economic value to be attached to plutonium for each examined. It is shown how the use of plutonium in fast reactors gives an opportunity for a non-proliferation policy not available when plutonium is used only in thermal reactors. From the technical considerations reviewed concerning plutonium and fast reactors it is shown that an economic regime involving international trade in spent thermal reactor fuel is possible which benefits equally those countries with fast reactors and those without and also assists in avoiding the proliferation of nuclear weapons. (U.K.)

  13. Micro-Valences: Affective valence in neutral everyday objects

    Directory of Open Access Journals (Sweden)

    Sophie eLebrecht

    2012-04-01

    Full Text Available Affective valence influences both our cognition and our perception of the world. Indeed, the speed and quality with which we recognize objects in a visual scene can vary dramatically depending on its affective content. However, affective processing of visual objects has been typically studied using only stimuli with strong affective valences (e.g., guns or roses. Here we explore whether affective valence must be strong or obvious to exert an effect on our perception. We conclude that the majority of objects carry some affective valence (micro-valences and, thus, nominally neutral objects are not really neutral. Functionally, the perception of valence in everyday objects facilitates perceptually-driven choice behavior, decision-making, and affective responses.

  14. Plutonium in nature; Le plutonium dans la nature

    Energy Technology Data Exchange (ETDEWEB)

    Madic, C.

    1994-12-31

    Plutonium in nature comes from natural sources and anthropogenic ones. Plutonium at the earth surface comes principally from anthropogenic sources. It is easily detectable in environment. The plutonium behaviour in environment is complex. It seems necessary for the future to reduce releases in environment, to improve predictive models of plutonium behaviour in geosphere, to precise biological impact of anthropogenic plutonium releases.

  15. Adsorption-desorption characteristics of plutonium and americium with sediment particles in the estuarine environment: studies using plutonium-237 and americium-241

    International Nuclear Information System (INIS)

    Murray, C.N.; Fukai, R.

    1975-01-01

    The particle formation of plutonium and americium, their adsorption onto fresh water sediments and the desorption from the sediments in sea water were studied in the Laboratory under simulated river-estuary conditions, using γ-emitting plutonium-237 and americium-241. The results of the experiments show that the particle formation of plutonium depends on its valence states, on pH and on the salinity of the medium. For river water at pH4, some 25%, 20% and 30% of the added 237 Pu was in particulate form, larger than 0.45 μm, for Pu (III), Pu (IV) and Pu (VI), respectively, while 65%, 90% and 50% of the respective valence states was associated with particles at pH 8. In sea water the general pattern remains similar, although Pu (VI) is more soluble in sea water owing to higher ligand concentrations for carbonate and bicarbonate complexes. The pH-dependency of particle formation of Am (III) is more steep than that of plutonium and seems to be influenced by colloidal substances occurring in the experimental media. The adsorption-desorption characteristics of plutonium and americium with the sediment in river water as well as sea water reflect the characteristics of their particle formation, being dependent upon such properties as valence states, the pH and salinity of the medium. A sewage effluent added to the media has small but measurable effects on the adsorption-desorption processes of plutonium. (author)

  16. Micro-Valences: Affective valence in neutral everyday objects

    OpenAIRE

    Sophie eLebrecht; Moshe eBar; Lisa F Barrett; Michael J Tarr

    2012-01-01

    Affective valence influences both our cognition and our perception of the world. Indeed, the speed and quality with which we recognize objects in a visual scene can vary dramatically depending on its affective content. However, affective processing of visual objects has been typically studied using only stimuli with strong affective valences (e.g., guns or roses). Here we explore whether affective valence must be strong or obvious to exert an effect on our perception. We conclude that the maj...

  17. X-ray photoemission study of plutonium metal

    International Nuclear Information System (INIS)

    Baptist, R.

    1982-01-01

    The x-ray induced photoemission from clean pure plutonium metal is described and the results for both core and valence levels are compared with previous measurements on light actinides. It is found that, as in thorium and urnaium, the configuration interaction plays an important role for core levels, in particular for those of the n=5 shell. The experimental valence-band spectrum confirms the existence of 5f states at the Fermi level and is compared with a density of states of FCC Pu derived from a recent relativistic band structure calculation. (author)

  18. Properties of plutonium

    International Nuclear Information System (INIS)

    Ahn, Jin Su; Yoon, Hwan Ki; Min, Kyung Sik; Kim, Hyun Tae; Ahn, Jong Sung; Kwag, Eon Ho; Ryu, Keon Joong

    1996-03-01

    Plutonium has unique chemical and physical properties. Its uniqueness in use has led to rare publications, in Korea. This report covers physical aspects of phase change of metal plutonium, mechanical properties, thermal conductivity, etc, chemical aspects of corrosion, oxidation, how to produce plutonium from spent fuels by describing various chemical treatment methods, which are currently used and were used in the past. It also contains characteristics of the purex reprocessing process which is the most widely used nowadays. And show processes to purify and metalize from recovered plutonium solution. Detection and analysis methods are introduced with key pints for handling, critical safety, toxicity, and effects on peoples. This report gives not only a general idea on what plutonium is, rather than deep technical description, but also basic knowledge on plutonium production and safeguards diversion from the view point of nonproliferation. 18 refs. (Author) .new

  19. Civil plutonium management

    International Nuclear Information System (INIS)

    Sicard, B.; Zaetta, A.

    2004-01-01

    During 1960 and 1970 the researches on the plutonium recycling in fast neutrons reactors were stimulated by the fear of uranium reserves diminishing. At the beginning of 1980, the plutonium mono-recycling for water cooled reactors is implementing. After 1990 the public opinion concerning the radioactive wastes management and the consequences of the disarmament agreements between Russia and United States, modified the context. This paper presents the today situation and technology associated to the different options and strategical solutions of the plutonium management: the plutonium use in the world, the neutronic characteristics, the plutonium effect on the reactors characteristics, the MOX behavior in the reactors, the MOX fabrication and treatment, the possible improvements to the plutonium use, the concepts performance in a nuclear park. (A.L.B.)

  20. Properties of plutonium

    Energy Technology Data Exchange (ETDEWEB)

    Ahn, Jin Su; Yoon, Hwan Ki; Min, Kyung Sik; Kim, Hyun Tae; Ahn, Jong Sung; Kwag, Eon Ho; Ryu, Keon Joong [Korea Atomic Energy Research Institute, Daeduk (Korea, Republic of)

    1996-03-01

    Plutonium has unique chemical and physical properties. Its uniqueness in use has led to rare publications, in Korea. This report covers physical aspects of phase change of metal plutonium, mechanical properties, thermal conductivity, etc, chemical aspects of corrosion, oxidation, how to produce plutonium from spent fuels by describing various chemical treatment methods, which are currently used and were used in the past. It also contains characteristics of the purex reprocessing process which is the most widely used nowadays. And show processes to purify and metalize from recovered plutonium solution. Detection and analysis methods are introduced with key pints for handling, critical safety, toxicity, and effects on peoples. This report gives not only a general idea on what plutonium is, rather than deep technical description, but also basic knowledge on plutonium production and safeguards diversion from the view point of nonproliferation. 18 refs. (Author) .new.

  1. World status report: plutonium

    International Nuclear Information System (INIS)

    Dircks, W.

    1992-01-01

    In a recent speech in Japan, the Deputy Director General of the International Atomic Energy Agency (IAEA) said that the economic case for reprocessing spent nuclear fuel had been severely eroded. An edited version of the speech is given. The changed prospects for nuclear energy is given as the reason why the demand for plutonium has declined sharply. The oil crisis of the 1970s reduced the demand for electric power and the economic justification for the use of recycled plutonium. The stockpile of isolated plutonium is growing rapidly giving rise to worries about its security. From this point of view, isolated plutonium is best kept in reactor fuel not separated out. In this connection the IAEA has offered to help in the storage of plutonium so that vigorous safety and security requirements are met. In Japan there is a debate about the plutonium which is dependent on the future of the fast breeder reactor programme. (UK)

  2. Progress on plutonium stabilization

    International Nuclear Information System (INIS)

    Hurt, D.

    1996-01-01

    The Defense Nuclear Facilities Safety Board has safety oversight responsibility for most of the facilities where unstable forms of plutonium are being processed and packaged for interim storage. The Board has issued recommendations on plutonium stabilization and has has a considerable influence on DOE's stabilization schedules and priorities. The Board has not made any recommendations on long-term plutonium disposition, although it may get more involved in the future if DOE develops plans to use defense nuclear facilities for disposition activities

  3. PLUTONIUM-ZIRCONIUM ALLOYS

    Science.gov (United States)

    Schonfeld, F.W.; Waber, J.T.

    1960-08-30

    A series of nuclear reactor fuel alloys consisting of from about 5 to about 50 at.% zirconium (or higher zirconium alloys such as Zircaloy), balance plutonium, and having the structural composition of a plutonium are described. Zirconium is a satisfactory diluent because it alloys readily with plutonium and has desirable nuclear properties. Additional advantages are corrosion resistance, excellent fabrication propenties, an isotropie structure, and initial softness.

  4. Cigarette smoke and plutonium

    International Nuclear Information System (INIS)

    Filipy, R.E.

    1983-01-01

    The major objective of this project is to obtain experimental data that are directly applicable to resolving the question of whether cigarette smokers are at greater risk than nonsmokers to potential health effects of inhaled plutonium. Because cigarette smokers constitute a large fraction of the population, a synergistic effect of plutonium and cigarette smoke might influence estimates of the health risk for plutonium and other transuranics released to the environment

  5. Intermediate valence spectroscopy

    International Nuclear Information System (INIS)

    Gunnarsson, O.; Schoenhammer, K.

    1987-01-01

    Spectroscopic properties of intermediate valence compounds are studied using the Anderson model. Due to the large orbital and spin degeneracy N/sub f/ of the 4f-level, 1/N/sub f/ can be treated as a small parameter. This approach provides exact T = 0 results for the Anderson impurity model in the limit N/sub f/ → ∞, and by adding 1/N/sub f/ corrections some properties can be calculated accurately even for N/sub f/ = 1 or 2. In particular valence photoemission and resonance photoemission spectroscopies are studied. A comparison of theoretical and experimental spectra provides an estimate of the parameters in the model. Core level photoemission spectra provide estimates of the coupling between the f-level and the conduction states and of the f-level occupancy. With these parameters the model gives a fair description of other electron spectroscopies. For typical parameters the model predicts two structures in the f-spectrum, namely one structure at the f-level and one at the Fermi energy. The resonance photoemission calculation gives a photon energy dependence for these two peaks in fair agreement with experiment. The peak at the Fermi energy is partly due to a narrow Kondo resonance, resulting from many-body effects and the presence of a continuous, partly filled conduction band. This resonance is related to a large density of low-lying excitations, which explains the large susceptibility and specific heat observed for these systems at low temperatures. 38 references, 11 figures, 2 tables

  6. Perspective on plutonium

    International Nuclear Information System (INIS)

    Sun, L.S.

    1993-01-01

    This paper is intended as a brief overview on the element plutonium. Plutonium is the first primarily man-made element to play a significant role not only in technological development, but also in the economic growth of many countries. The importance of plutonium centers around its enormous energy making it ideal for wide-scale use in reactors, while the nuclear industry continues to work toward improving safety and efficiency of plutonium as a reactor fuel politicians and the public still debate over the safety and benefits of nuclear power. (30 refs.)

  7. Plutonium uptake by the green alga Scenedesmus obliquus (Turp) Kutz, as a function of isotope and oxidation state

    Energy Technology Data Exchange (ETDEWEB)

    Tkacik, M.F.

    1977-01-01

    This study was designed to determine the effect of plutonium chemical valence state on the availability of small concentrations of /sup 238/Pu and /sup 239/Pu to algae. The uptake experiments involved the green alga Scenedesmus obliquus, grown in batch cultures. Plutonium concentrations accumulated by this alga were linearly related to plutonium concentrations. There was no significant difference (rho = 0.05) in algal plutonium accumulations, on a mass basis, of either /sup 238/Pu or /sup 239/Pu in either Pu/sup +4/ or Pu/sup +6/ oxidation state at the concentrations studied.

  8. Plutonium uptake by the green alga Scenedesmus obliquus (Turp) Kutz, as a function of isotope and oxidation state

    International Nuclear Information System (INIS)

    Tkacik, M.F.

    1977-01-01

    This study was designed to determine the effect of plutonium chemical valence state on the availability of small concentrations of 238 Pu and 239 Pu to algae. The uptake experiments involved the green alga Scenedesmus obliquus, grown in batch cultures. Plutonium concentrations accumulated by this alga were linearly related to plutonium concentrations. There was no significant difference (rho = 0.05) in algal plutonium accumulations, on a mass basis, of either 238 Pu or 239 Pu in either Pu +4 or Pu +6 oxidation state at the concentrations studied

  9. Adsorption-Desorption Characteristics of Plutonium and Americium with Sediment Particles in the Estuarine Environment

    International Nuclear Information System (INIS)

    Murray, C.N.; Fukai, R.

    1976-01-01

    The particle formation of plutonium and americium, their adsorption onto fresh water sediments and the desorption from the sediments in sea water were studied in the Laboratory under simulated river-estuary conditions, using γ-emitting plutonium-237 and americium-241. The results of the experiments show that the particle formation of plutonium depends on its valence states, on pH and on the salinity of the medium. For river water at pH4, some 25%, 20% and 30% of the added 237 Pu was in particulate form, larger than 0.45pm, for Pu (III), Pu (IV) and Pu (VI), respectively, while 65%, 90% and 50% of the respective valence states was associated with particles at pH 8. In sea water the general pattern remains similar, although Pu (VI) is more soluble in sea water owing to higher ligand concentrations for carbonate and bicarbonate complexes. The pH-dependency of particle formation of Am (III) is more steep than that of plutonium and seems to be influenced by colloidal substances occurring in the experimental media. The adsorption-desorption characteristics of plutonium and americium with the sediment in river water as well as sea water reflect the characteristics of their particle formation, being dependent upon such properties as valence states, the pH and salinity of the medium. A sewage effluent added to the media has small but measurable effects on the adsorption-desorption processes of plutonium. (author)

  10. Electronic structure, phase transitions and diffusive properties of elemental plutonium

    Science.gov (United States)

    Setty, Arun; Cooper, B. R.

    2003-03-01

    We present a SIC-LDA-LMTO based study of the electronic structure of the delta, alpha and gamma phases of plutonium, and also of the alpha and gamma phases of elemental cerium. We find excellent agreement with the experimental densities and magnetic properties [1]. Furthermore, detailed studies of the computational densities of states for delta plutonium, and comparison with the experimental photoemission spectrum [2], provide evidence for the existence of an unusual fluctuating valence state. Results regarding the vacancy formation and self-diffusion in delta plutonium will be presented. Furthermore, a study of interface diffusion between plutonium and steel (technologically relevant in the storage of spent fuel) or other technologically relevant alloys will be included. Preliminary results regarding gallium stabilization of delta plutonium, and of plutonium alloys will be presented. [1] M. Dormeval et al., private communication (2001). [2] A. J. Arko, J. J. Joyce, L. Morales, J. Wills, and J. Lashley et. al., Phys. Rev. B, 62, 1773 (2000). [3] B. R. Cooper et al, Phil. Mag. B 79, 683 (1999); B.R. Cooper, Los Alamos Science 26, 106 (2000)); B.R. Cooper, A.K. Setty and D.L.Price, to be published.

  11. Cigarette smoke and plutonium

    International Nuclear Information System (INIS)

    Anon.

    1981-01-01

    The overall objective of this study is to determine whether cigarette smoking increases the probability of plutonium-induced lung cancer. Initial experiments, designed to characterize the effect of chronic cigarette smoke exposure on pulmonary clearance of plutonium aerosols, are described

  12. The toxicity of plutonium

    International Nuclear Information System (INIS)

    Crouse, P.L.

    1994-01-01

    Shipments of plutonium occasionally pass around the Cape coastal waters on its way to Japan from Europe. This invariably leads to a great deal of speculation of the dangers involved and of the extreme toxicity of plutonium, with the media and environmental groups claiming that (a) plutonium is the most toxic substance known to man, and that (b) a few kilograms of plutonium ground finely and dispersed in the atmosphere could kill every human being on earth. Comparisons with other poisons are drawn, e.g. common inorganic chemicals and biological agents. The original scare around the extraordinary toxicity of Pu seems to have started in 1974 with the claims of Tamplin and Cochran's hot particle theory about plutonium lodging in the sensitive portions of the lungs in small concentrated aggregates where they are much more effective in producing cancers. This theory, however, is regarded as thoroughly discredited by the experts in the field of radiotoxicity. 8 refs

  13. Plutonium storage criteria

    Energy Technology Data Exchange (ETDEWEB)

    Chung, D. [Scientech, Inc., Germantown, MD (United States); Ascanio, X. [Dept. of Energy, Germantown, MD (United States)

    1996-05-01

    The Department of Energy has issued a technical standard for long-term (>50 years) storage and will soon issue a criteria document for interim (<20 years) storage of plutonium materials. The long-term technical standard, {open_quotes}Criteria for Safe Storage of Plutonium Metals and Oxides,{close_quotes} addresses the requirements for storing metals and oxides with greater than 50 wt % plutonium. It calls for a standardized package that meets both off-site transportation requirements, as well as remote handling requirements from future storage facilities. The interim criteria document, {open_quotes}Criteria for Interim Safe Storage of Plutonium-Bearing Solid Materials{close_quotes}, addresses requirements for storing materials with less than 50 wt% plutonium. The interim criteria document assumes the materials will be stored on existing sites, and existing facilities and equipment will be used for repackaging to improve the margin of safety.

  14. Plutonium roundtable discussion

    International Nuclear Information System (INIS)

    Penneman, R.A.

    1982-01-01

    The roundtable discussion began with remarks by the chairman who pointed out the complicated nature of plutonium chemistry. Judging from the papers presented at this symposium, he noticed a pattern which indicated to him the result of diminished funding for investigation of basic plutonium chemistry and funding focused on certain problem areas. Dr. G.L. silver pointed to plutonium chemists' erroneous use of a simplified summary equation involving the disproportionation of Pu(EV) and their each of appreciation of alpha coefficients. To his appreciation of alpha coefficients. To his charges, Dr. J.T. Bell spoke in defense of the chemists. This discussion was followed by W.W. Schulz's comments on the need for experimental work to determine solubility data for plutonium in its various oxidation states under geologic repository conditions. Discussion then turned to plutonium pyrachemical process with Dana C. Christensen as the main speaker. This paper presents edited versions of participants' written version

  15. Plutonium storage phenomenology

    International Nuclear Information System (INIS)

    Szempruch, R.

    1995-12-01

    Plutonium has been produced, handled, and stored at Department of Energy (DOE) facilities since the 1940s. Many changes have occurred during the last 40 years in the sources, production demands, and end uses of plutonium. These have resulted in corresponding changes in the isotopic composition as well as the chemical and physical forms of the processed and stored plutonium. Thousands of ordinary food pack tin cans have been used successfully for many years to handle and store plutonium. Other containers have been used with equal success. This paper addressees the exceptions to this satisfactory experience. To aid in understanding the challenges of handling plutonium for storage or immobilization the lessons learned from past storage experience and the necessary countermeasures to improve storage performance are discussed

  16. Solvent extraction of irradiated neptunium targets. I. Valence stabilization

    International Nuclear Information System (INIS)

    Thompson, G.H.; Thompson, M.C.

    1977-01-01

    Solvent extraction of 237 Np and 238 Pu from irradiated neptunium is being investigated as a possible replacement for the currently used anion exchange process at the Savannah River Plant. Solvent extraction would reduce separations costs and waste volume and increase the production rate. The major difficulty in solvent extraction processing is maintaining neptunium and plutonium in the extractable IV or VI valence states during initial extraction. This study investigated the stability of these states. Results show that: The extractable M(IV) valence states of neptunium and plutonium are mutually unstable in plant dissolver solution (2 g/l 237 Np, 0.4 g/l 238 Pu, 1.2M Al 3+ , 4.6M NO 3 - , and 1M H + ). The reaction rates producing inextractable species from extractable M(IV) or M(VI) are fast enough that greater than or equal to 99.9 percent extractable species in 237 Np-- 238 Pu mixtures cannot be maintained for a practicable processing period

  17. Toxicology of plutonium

    International Nuclear Information System (INIS)

    Bair, W.J.

    1974-01-01

    Data are reviewed from studies on the toxicity of Pu in experimental animals. Of the several plutonium isotopes, only 238 Pu and 239 Pu have been studied well. Sufficient results have been obtained to show that the behavior of 238 Pu in biological systems and the resulting biological effects cannot be precisely predicted from studies of 239 Pu. This probably applies also to other radiologically important plutonium isotopes which have half-lives ranging from 45 days to 10 7 years and decay by β-emission, electron capture, and spontaneous fission, as well as by emission of α-particles. All the biological effects of plutonium described in this review are attributed to alpha-particle radiation emitted by the plutonium. However, since plutonium is a chemically active heavy metal, one cannot ignore the possibility of chemical toxicity of the low-specific-activity isotopes, 239 Pu, 242 Pu, and 244 Pu. The preponderance of our knowledge of plutonium toxicology has come from short-term studies of relatively high dosage levels in several animal species. The consequences of high-level internal exposures can be predicted with confidence in experimental animals and probably also in man. However, considering the care with which plutonium is handled in the nuclear industry, a high-level contamination event is unlikely. Considerably less is known about the long-term effects of low levels of contamination. (250 references) (U.S.)

  18. The plutonium danger

    International Nuclear Information System (INIS)

    Ruiter, W. de

    1983-01-01

    Nobody can ignore the fact that plutonium is potentially very dangerous and the greatest danger concerning it lies in the spreading of nuclear weapons via nuclear energy programmes. The following seven different attitudes towards this problem are presented and discussed: 1) There is no connection between peaceful and military applications; 2) The problem cannot be prevented; 3) A technical solution must be found; 4) plutonium must be totally inaccessible to countries involved in acquiring nuclear weapons; 5) The use of plutonium for energy production should only occur in one multinational centre; 6) Dogmas in the nuclear industry must be enfeebled; 7) All developments in this area should stop. (C.F.)

  19. Plutonium Vulnerability Management Plan

    International Nuclear Information System (INIS)

    1995-03-01

    This Plutonium Vulnerability Management Plan describes the Department of Energy's response to the vulnerabilities identified in the Plutonium Working Group Report which are a result of the cessation of nuclear weapons production. The responses contained in this document are only part of an overall, coordinated approach designed to enable the Department to accelerate conversion of all nuclear materials, including plutonium, to forms suitable for safe, interim storage. The overall actions being taken are discussed in detail in the Department's Implementation Plan in response to the Defense Nuclear Facilities Safety Board (DNFSB) Recommendation 94-1. This is included as Attachment B

  20. Plutonium Plant, Trombay

    International Nuclear Information System (INIS)

    Yadav, J.S.; Agarwal, K.

    2017-01-01

    The journey of Indian nuclear fuel reprocessing started with the commissioning of Plutonium Plant (PP) at Trombay on 22"n"d January, 1965 with an aim to reprocess the spent fuel from research reactor CIRUS. The basic process chosen for the plant was Plutonium Uranium Reduction EXtraction (PUREX) process. In seventies, the plant was subjected to major design modifications and replacement of hardware, which later met the additional demand from research reactor DHRUVA. The augmented plutonium plant has been operating since 1983. Experience gained from this plant was very much helpful to design future reprocessing plant in the country

  1. Progress on plutonium stabilization

    Energy Technology Data Exchange (ETDEWEB)

    Hurt, D. [Defense Nuclear Facilities Safety Board, Washington, DC (United States)

    1996-05-01

    The Defense Nuclear Facilities Safety Board has safety oversight responsibility for most of the facilities where unstable forms of plutonium are being processed and packaged for interim storage. The Board has issued recommendations on plutonium stabilization and has has a considerable influence on DOE`s stabilization schedules and priorities. The Board has not made any recommendations on long-term plutonium disposition, although it may get more involved in the future if DOE develops plans to use defense nuclear facilities for disposition activities.

  2. Cigarette smoke and plutonium

    International Nuclear Information System (INIS)

    Filipy, R.E.

    1982-01-01

    The major objective of this project is to obtain experimental data that are directly applicable to resolving the question of whether cigarette smokers are at greater risk than nonsmokers to potential health effects of inhaled plutonium. Progress was made on two fronts during the past year. The autoradiographic technique developed from detection of plutonium on the interior surface of pulmonary airways (Annual Report, 1978) has been adapted to routine use in examining tracheas and bronchi of rats. Also, dogs exposed to cigarette smoke for over a year after inhalation of plutonium were killed and necropsied

  3. Plutonium spectrophotometric analysis

    International Nuclear Information System (INIS)

    Esteban, A.; Cassaniti, P.; Orosco, E.H.

    1990-01-01

    Plutonium ions in solution have absorption spectra so different that it is possible to use them for analytical purposes. Detailed studies have been performed in nitric solutions. Some very convenient methods for the determination of plutonium and its oxidation states, especially the ratios Pu(III):Pu(IV) and Pu(IV):Pu(VI) in a mixture of both, have been developed. These methods are described in this paper, including: a) Absorption spectra for plutonium (III), (IV), (VI) and mixtures. b) Relative extinction coefficients for the above mentioned species. c) Dependences of the relative extinction coefficients on the nitric acid concentration and the plutonium VI deviation from the Beer-Lambert law. The developed methods are simple and rapid and then, suitable in process control. Accuracy is improved when relative absorbance measurements are performed or controlled the variables which have effect on the spectra and extinction coefficients. (Author) [es

  4. French plutonium management program

    International Nuclear Information System (INIS)

    Greneche, D.

    2002-01-01

    The French plutonium management program is summarized in this paper. The program considers nuclear generation as a major component of national electric power supply and includes the reprocessing of the spent fuel. (author)

  5. Learning more about plutonium

    International Nuclear Information System (INIS)

    2008-01-01

    This digest brochure explains what plutonium is, where it comes from, how it is used, its recycling into Mox fuel, its half life, historical discovery, its presence in the environment, toxicity and radioactivity. (J.S.)

  6. Plutonium safe handling

    International Nuclear Information System (INIS)

    Tvehlov, Yu.

    2000-01-01

    The abstract, prepared on the basis of materials of the IAEA new leadership on the plutonium safe handling and its storage (the publication no. 9 in the Safety Reports Series), aimed at presenting internationally acknowledged criteria on the radiation danger evaluation and summarizing the experience in the safe management of great quantities of plutonium, accumulated in the nuclear states, is presented. The data on the weapon-class and civil plutonium, the degree of its danger, the measures for provision of its safety, including the data on accident radiation consequences with the fission number 10 18 , are presented. The recommendations, making it possible to eliminate the super- criticality danger, as well as ignition and explosion, to maintain the tightness of the facility, aimed at excluding the radioactive contamination and the possibility of internal irradiation, to provide for the plutonium security, physical protection and to reduce irradiation are given [ru

  7. Determination of plutonium in pure plutonium nitrate solutions - Gravimetric method

    International Nuclear Information System (INIS)

    1987-01-01

    This International Standard specifies a precise and accurate gravimetric method for determining the concentration of plutonium in pure plutonium nitrate solutions and reference solutions, containing between 100 and 300 g of plutonium per litre, in a nitric acid medium. The weighed portion of the plutonium nitrate is treated with sulfuric acid and evaporated to dryness. The plutonium sulfate is decomposed and formed to oxide by heating in air. The oxide is ignited in air at 1200 to 1250 deg. C and weighed as stoichiometric plutonium dioxide, which is stable and non-hygroscopic

  8. Plutonium in coniferous forests

    International Nuclear Information System (INIS)

    Rantavaara, A.; Kostiainen, E.

    2002-01-01

    Our aim was to study the uptake of plutonium by trees, undervegetation and some wild foods. The ratio of 238 Pu/ 239,240 Pu in soil samples was determined for comparisons of the fallout origin. In twelve years the Chernobyl derived plutonium has not reached the mineral soil. This refers to a very slow downward migration in podsolic soil. The study confirmed also the low Pu uptake by vegetation and an insignificant contribution to human doses through wild foods. (au)

  9. Partial equilibrium in induced redox reactions of plutonium

    Energy Technology Data Exchange (ETDEWEB)

    Nikol' skii, B P; Posvol' skii, M V; Krylov, L I; Morozova, Z P

    1975-01-01

    A study was made of oxidation-reduction reactions of Pu in buffer solutions containing bichromate and a reducing agent which reacted with hexavalent chromium at pH=3.5. In most cases sodium nitrite was used. A rather slow reduction of Pu (6) with NaNO/sub 2/ in the course of which tetravalent plutonium was formed via disproportionation reaction of plutonium (5), became very rapid upon the addition of bichromate to the solution. The yield of tetravalent plutonium increased with an increase in the concentration of NaNO/sub 2/ and the bichromate but never reached 100%. This was due to a simultaneous occurrenc of the induced oxidation reaction of Pu(4), leading to a partial equilibrium between the valence forms of plutonium in the nitrite-bichromate system which on the whole was in a nonequilibrium state. It was shown that in the series of reactions leading to the reduction of plutonium the presence of bivalent chromium was a necessary link.

  10. Valence effects of sorption: laboratory control of valence state

    International Nuclear Information System (INIS)

    Meyer, R.E.; Arnold, W.D.; Case, F.I.

    1984-01-01

    Estimation of the rates of migration of nuclides from nuclear waste repositories required knowledge of the interaction of these nuclides with the components of the geological formations in the path of the migration. These interactions will be dependent upon the valence state and speciation of the nuclide. If the valence state is not known, then there can be little confidence in use of the data for safety analysis. An electrochemical method of valence state control was developed which makes use of a porous electrode in a flow system containing a column of the adsorbent. By use of this method and solvent extraction analyses of the valence states, a number of reactions of interest to HLW repositories were investigated. These include the reduction of Np(V) and Tc(VII) by crushed basalt and other minerals. For the reduction of Np(V) by basalt, the experiments indicate that sorption on basalt increases with pH and that most of the Np is reduced to Np(IV). The adsorbed Np(IV) is very difficult to remove from the basalt. For the experiments with Tc(VII), the results are considerably more complicated. The results of these experiments are used to assess some of the techniques and methods currently used in safety analyses of proposed HLW repositories. Perhaps the most important consideration is that predictive modeling of valence change reactions, such as the reduction of Np(V) and Tc(VII), must be used with considerable caution, and the occurrence of such reactions should be verified as best as possible with experiments using valence state control and analyses. 13 references, 3 figures, 1 table

  11. The comparative distribution of thorium and plutonium in human tissues

    International Nuclear Information System (INIS)

    Singh, Narayani P.; Shawki Amin Ibrahim; Cohen, Norman; Wrenn, McDonald E.

    1978-01-01

    Thorium is the most chemically and biologically similar natural element to the manmade element plutonium. Both are actinides, and for both the most stable valency state is +4, and solubility in natural body fluids is low. They are classified together in ICRP Lung Model. The present paper deals with the question of whether or not the analogy between the two actinides in terms of deposition and retention in human tissues is a good one. Preliminary results on the thorium contents ( 228,230 Th and 232 Th) of three sets of human tissues from a western U.S. town containing a uranium tailings pile are compared with the reported values of plutonium content of human tissues from the general populations who are exposed to environmental plutonium from fallout of nuclear detonations. Samples were taken at autopsy where sudden death had occurred. For the three isotopes of thorium, the ratio of the content of each (pCi/organ, normalized by organ weight to ICRP Reference Man) in lung to lymph nodes varies from 2-25 for individuals with a mean of 8; this is similar to that we infer from the literature for 239 , 240 Pu which suggests a ratio of lung to lymph nodes with a mean of approximately 7. However, the relative thorium contents of lung and liver are dissimilar, lung/liver for thorium being 3.5 and for plutonium 0.2 to 0.1. Similarly, the ratios of thorium and plutonium content of liver and bone vary significantly; the ratio for thorium is 0.1 and for plutonium 0.8 to 0.5. The most significant observation at this stage is that the relative accumulation of thorium in human liver is much less than that of plutonium. Some of the plausible reasons will be discussed. (author)

  12. Determination of uranium and plutonium by sequential potentiometric titration

    International Nuclear Information System (INIS)

    Kato, Yoshiharu; Takahashi, Masao

    1976-01-01

    The determination of uranium and plutonium in mixed oxide fuels has been developed by sequential potentiometric titration. A weighed sample of uranium and plutonium oxides is dissolved in a mixture of nitric and hydrofluoric acids and the solution is fumed with sulfuric acid. After the reduction of uranium and plutonium to uranium(IV) and plutonium(III) by chromium(II) sulfate, 5 ml of buffer solution (KCl-HCl, pH 1.0) is added to the solution. Then the solution is diluted to 30 ml with water and the pH of the solution is adjusted to 1.0 -- 1.5 with 1 M sodium hydroxide. The solution is stirred until the oxidation of the excess of chromium(II) by air is completed. After the removal of dissolved oxygen by bubbling nitrogen through the solution for 10 minutes, uranium (IV) is titrated with 0.1 N cerium(IV) sulfate. Then, plutonium is titrated by 0.02 N cerium(IV) sulfate. When a mixture of uranium and plutonium is titrated with 0.1 N potassium dichromate potentiometrically, the potential change at the end point of plutonium is very small and the end point of uranium is also unclear when 0.1 N potassium permanganate is used as a titrant. In the present method, nitrate, fluoride and copper(II) interfere with the determination of plutonium and uranium. Iron interferes quantitatively with the determination of plutonium but not of uranium. Results obtained in applying the proposed method to 50 mg of mixtures of plutonium and uranium ((7.5 -- 50))% Pu were accurate to within 0.15 mg of each element. (auth.)

  13. Localized description of valence fluctuations

    International Nuclear Information System (INIS)

    Alascio, B.; Allub, R.; Aligia, A.

    1979-07-01

    The authors set up a model for intermediate valence equivalent to the ''atomic'' limit of the Anderson Hamiltonian. Detailed analysis of this model shows that most of the essential characteristics of valence fluctuators are already present in this crudely simplified Hamiltonian. The spin-spin and the 4f charge-charge correlation functions are studied and it is shown that it is possible to define a spin fluctuation frequency ωsub(s.f.) and a charge fluctuation frequency ωsub(ch.f.).ωsub(s.f.) and ωsub(ch.f.) can differ considerably for some values of the parameters of the model. The magnetic susceptibility and the specific heat are calculated as functions of temperature and it is shown how the results simulate the behaviour found in valence fluctuators. (author)

  14. Plutonium-236 traces determination in plutonium-238 by α spectrometry

    International Nuclear Information System (INIS)

    Acena, M.L.; Pottier, R.; Berger, R.

    1969-01-01

    Two methods are described in this report for the determination of plutonium-236 traces in plutonium-238 by a spectrometry using semi-conductor detectors. The first method involves a direct comparison of the areas under the peaks of the α spectra of plutonium-236 and plutonium-238. The electrolytic preparation of the sources is carried out after preliminary purification of the plutonium. The second method makes it possible to determine the 236 Pu/ 238 Pu ratio by comparing the areas of the α peaks of uranium-232 and uranium-234, which are the decay products of the two plutonium isotopes respectively. The uranium in the source, also deposited by electrolysis, is separated from a 1 mg amount of plutonium either by a T.L.A. extraction, or by the use of ion-exchange resins. The report ends with a discussion of the results obtained with plutonium of two different origins. (authors) [fr

  15. Conversion of metal plutonium to plutonium dioxide by pyrochemical method

    Energy Technology Data Exchange (ETDEWEB)

    Panov, A.V.; Subbotin, V.G. [Russian Federal Nuclear Center, ALL-Russian Science and Research Institute of Technical Physics, Snezhinsk (Russian Federation); Mashirev, V.P. [ALL-Russian Science and Research Institute of Chemical Technology, Moscow (Russian Federation)

    2000-07-01

    Report contains experimental results on metal plutonium of weapon origin samples conversion to plutonium dioxide by pyrochemical method. Circuits of processes are described. Their advantages and shortcomings are shown. Parameters of plutonium dioxide powders (phase and fraction compositions, poured density) manufactured by pyrochemical method in RFNC-VNIITF are shown as well. (authors)

  16. Actinides: from heavy fermions to plutonium metallurgy

    International Nuclear Information System (INIS)

    Smith, J.L.; Fisk, Z.; Hecker, S.S.

    1984-01-01

    The actinide elements mark the emergence of 5f electrons. The f electrons possess sufficiently unusual characteristics that their participation in atomic binding often result in dramatic changes in properties. This provides an excellent opportunity to study the question of localization of electrons; a question that is paramount in predicting the physical and chemical properties of d and f electron transition metals. The transition region between localized (magnetic) and itinerant (often superconducting) behavior provides for many interesting phenomena such as structural instabilities (polymorphism), spin fluctuations, mixed valences, charge density waves, exceptional catalytic activity and hydrogen storage. This region offers most interesting behavior such as that exhibited by the actinide compounds UBe 13 and UPt 3 . Both compounds are heavy-fermion superconductors in which both magnetic and superconducting behavior exist in the same electrons. The consequences of f-electron bonding (which appears greatest at Plutonium) show dramatic effects on phase stability, alloying behavior, phase transformations and mechanical behavior

  17. METHOD OF PRODUCING PLUTONIUM TETRAFLUORIDE

    Science.gov (United States)

    Tolley, W.B.; Smith, R.C.

    1959-12-15

    A process is presented for preparing plutonium tetrafluoride from plutonium(IV) oxalate. The oxalate is dried and decomposed at about 300 deg C to the dioxide, mixed with ammonium bifluoride, and the mixture is heated to between 50 and 150 deg C whereby ammonium plutonium fluoride is formed. The ammonium plutonium fluoride is then heated to about 300 deg C for volatilization of ammonium fluoride. Both heating steps are preferably carried out in an inert atmosphere.

  18. Aqueous Solution Chemistry of Plutonium

    Energy Technology Data Exchange (ETDEWEB)

    Clark, David L. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2014-01-28

    Things I have learned working with plutonium: Chemistry of plutonium is complex; Redox equilibria make Pu solution chemistry particularly challenging in the absence of complexing ligands; Understanding this behavior is key to successful Pu chemistry experiments; There is no suitable chemical analog for plutonium.

  19. Physics of plutonium recycling

    International Nuclear Information System (INIS)

    2003-01-01

    The commercial recycling of plutonium as PuO 2 /UO 2 mixed-oxide (MOX) fuel is an established practice in pressurised water reactors (PWRs) in several countries, the main motivation being the consumption of plutonium arising from spent fuel reprocessing. Although the same motivating factors apply in the case of boiling water reactors (BWRs), they have lagged behind PWRs for various reasons, and MOX utilisation in BWRs has been implemented in only a few reactors to date. One of the reasons is that the nuclear design of BWR MOX assemblies (or bundles) is more complex than that of PWR assemblies. Recognizing the need and the timeliness to address this issue at the international level, the OECD/NEA Working Party on the Physics of Plutonium Fuels and Innovative Fuel Cycles (WPPR) conducted a physics code benchmark test for a BWR assembly. This volume reports on the benchmark results and conclusions that can be drawn from it. (authors)

  20. Plutonium microstructures. Part 1

    International Nuclear Information System (INIS)

    Cramer, E.M.; Bergin, J.B.

    1981-09-01

    This report is the first of three parts in which Los Alamos and Lawrence Livermore National Laboratory metallographers exhibit a consolidated set of illustrations of inclusions that are seen in plutonium metal as a consequence of inherent and tramp impurities, alloy additions, and thermal or mechanical treatments. This part includes illustrations of nonmetallic and intermetallic inclusions characteristic of major impurity elements as an aid to identifying unknowns. It also describes historical aspects of the increased purity of laboratory plutonium samples, and it gives the composition of the etchant solutions and describes the etching procedure used in the preparation of each illustrated sample. 25 figures

  1. Plutonium isotopes in the environment

    International Nuclear Information System (INIS)

    Holm, E.

    1977-12-01

    Determination of plutonium and americium by ion exchange and alpha-spectrometry. Deposition of global fall-out and accumulated area-content of 238 Pu, 239 Pu, 240 Pu, 241 Pu, 242 Pu and 241 Am in central Sweden (62.3 deg N, 12.4 deg E), by using the lichen species Cladonia alpestris as bioindicator. Retention and distribution of plutonium in carpets of lichen and soil. Transfer of plutonium from lichen to reindeer and man. Absorbed dose in reindeer and man from plutonium. Basic studies of plutonium and americium in the western Mediterranean surface waters, with emphases on particulate form of the transuranics. (author)

  2. Investigation of plutonium (4) hydroxoformates

    International Nuclear Information System (INIS)

    Andryushin, V.G.; Belov, V.A.; Galaktionov, S.V.; Kozhevnikov, P.B.; Matyukha, V.A.; Shmidt, V.S.

    1982-01-01

    Deposition processes of plutonium (4) hydroxoformates in the system Pu(NO 3 ) 4 -HNO 3 -HCoOH-N6 4 OH-H 2 O have been studied in pH range 0.2-10.7 at total plutonium concentration in the system 100 g/l. It is shown that under the conditions plutonium (4) hydrolysis takes place with the formation of hydroxoformates. A local maximum of plutonium (4) hydroxoformate solubility in the range pH=3.8-4.8, which is evidently conditioned by the formation of soluble formate complex of plutonium in the region, is pointed out. The basic plutonium (4) formates of the composition PuOsub(x)(OH)sub(y)(COOH)sub(4-2x-y)xnHsub(2)O, where 1,3 >=x >= 0.7, 1.7 >= y >= 1.0 and n=1.5-7.0, are singled out, their thermal stability being studied. Density of the crystals and plutonium dioxide, formed during their thermal decomposition, is measured. It is established that for plutonium (4) hydroxoformates common regularities of the influence of salt composition (OH - -, CHOO - - and H 2 O-group numbers in the mulecule) on position of temperature decomposition effects and on the density of compounds, which have been previously found during the study of thorium and plutonium hydroxosalts are observed. It is shown that the density of plutonium dioxide decreases with the increase of hydration and hydrolysis degree of the initial plutonium hydroxoformate

  3. International plutonium policy

    International Nuclear Information System (INIS)

    1979-02-01

    As any other fissile material, the plutonium raises several utilization problems, particularly as far as diversion by sub-national groups or proliferation are concerned. The purpose of this paper is to show that these problems can be given reasonable solutions avoiding over penalties on energy production

  4. Plutonium safety training course

    International Nuclear Information System (INIS)

    Moe, H.J.

    1976-03-01

    This course seeks to achieve two objectives: to provide initial safety training for people just beginning work with plutonium, and to serve as a review and reference source for those already engaged in such work. Numerous references have been included to provide information sources for those wishing to pursue certain topics more fully. The first part of the course content deals with the general safety approach used in dealing with hazardous materials. Following is a discussion of the four properties of plutonium that lead to potential hazards: radioactivity, toxicity, nuclear properties, and spontaneous ignition. Next, the various hazards arising from these properties are treated. The relative hazards of both internal and external radiation sources are discussed, as well as the specific hazards when plutonium is the source. Similarly, the general hazards involved in a criticality, fire, or explosion are treated. Comments are made concerning the specific hazards when plutonium is involved. A brief summary comparison between the hazards of the transplutonium nuclides relative to 239 Pu follows. The final portion deals with control procedures with respect to contamination, internal and external exposure, nuclear safety, and fire protection. The philosophy and approach to emergency planning are also discussed

  5. Atomic spectrum of plutonium

    International Nuclear Information System (INIS)

    Blaise, J.; Fred, M.; Gutmacher, R.G.

    1984-08-01

    This report contains plutonium wavelengths, energy level classifications, and other spectroscopic data accumulated over the past twenty years at Laboratoire Aime Cotton (LAC) Argonne National Laboratory (ANL), and Lawrence Livermore National Laboratory (LLNL). The primary purpose was term analysis: deriving the energy levels in terms of quantum numbers and electron configurations, and evaluating the Slater-Condon and other parameters from the levels

  6. Plutonium: An introduction

    International Nuclear Information System (INIS)

    Condit, R.H.

    1993-10-01

    This report is a summary of the history and properties of plutonium. It presents information on the atoms, comparing chemical and nuclear properties. It looks at the history of the atom, including its discovery and production methods. It summarizes the metallurgy and chemistry of the element. It also describes means of detecting and measuring the presence and quantity of the element

  7. Plutonium Disposition by Immobilization

    International Nuclear Information System (INIS)

    Gould, T.; DiSabatino, A.; Mitchell, M.

    2000-01-01

    The ultimate goal of the Department of Energy (DOE) Immobilization Project is to develop, construct, and operate facilities that will immobilize between 17 to 50 tonnes (MT) of U.S. surplus weapons-usable plutonium materials in waste forms that meet the ''spent fuel'' standard and are acceptable for disposal in a geologic repository. Using the ceramic can-in-canister technology selected for immobilization, surplus plutonium materials will be chemically combined into ceramic forms which will be encapsulated within large canisters of high level waste (HLW) glass. Deployment of the immobilization capability should occur by 2008 and be completed within 10 years. In support of this goal, the DOE Office of Fissile Materials Disposition (MD) is conducting development and testing (D and T) activities at four DOE laboratories under the technical leadership of Lawrence Livermore National Laboratory (LLNL). The Savannah River Site has been selected as the site for the planned Plutonium Immobilization Plant (PIP). The D and T effort, now in its third year, will establish the technical bases for the design, construction, and operation of the U. S. capability to immobilize surplus plutonium in a suitable and cost-effective manner. Based on the D and T effort and on the development of a conceptual design of the PIP, automation is expected to play a key role in the design and operation of the Immobilization Plant. Automation and remote handling are needed to achieve required dose reduction and to enhance operational efficiency

  8. Plutonium cores of zenith

    Energy Technology Data Exchange (ETDEWEB)

    Barclay, F R; Cameron, I R; Drageset, A; Freemantle, R G; Wilson, D J

    1965-03-15

    The report describes a series of experiments carried out with plutonium fuel in the heated zero power reactor ZENITH, with the aim of testing current theoretical methods, with particular reference to excess reactivity, temperature coefficients, differential spectrum and reaction rate distributions. Two cores of widely different fissile/moderator atom ratios were loaded in order to test the theory under significantly varied spectrum conditions.

  9. Plutonium and textbooks

    International Nuclear Information System (INIS)

    Silver, G.L.

    2008-01-01

    Chemical equilibrium is not characterized by equilibrium constants alone. At least one conservation principle is necessary. Textbook descriptions of plutonium chemistry that are based on two-reaction-product disproportionation equations, or do not recognize the conservation principles, are incomplete and potentially misleading. (author)

  10. Japan's plutonium economy

    International Nuclear Information System (INIS)

    Hecht, M.M.

    1994-01-01

    Japan's plutonium economy is based on the most efficient use of nuclear energy, as envisioned under the Atoms for Peace program of the 1950s and 1960s. The nuclear pioneers assumed that all nations would want to take full advantage of atomic energy, recycling waste into new fuel to derive as much energy as possible from this resource

  11. Transport of plutonium nitrate

    International Nuclear Information System (INIS)

    1982-02-01

    This leaflet discusses the subject under the headings: why do we need plutonium; why must we transport it; what action is carried out; how is it moved; what are the risks. The transport of the material in specially designed containers, from Dounreay in Caithness by road and sea to Sellafield in Cumbria, is described. (U.K.)

  12. Plutonium and other transuranics in small vertebrates: a review

    International Nuclear Information System (INIS)

    Bradley, W.G.; Moor, K.S.; Naegle, S.R.

    1977-01-01

    The published data relevant to transuranics in small vertebrates inhabiting terrestrial environments is reviewed. Experimental results indicate that atomic size and valence state affect rates of absorption, transportation, and excretion of transuranics in living systems. Whereas there is a marked tendency for transuranics to hydrolyze to insoluble colloidal products at physiological pH, complexing agents and chelation enhance solubility and transportability. The natural modes of uptake of transuranics by vertebrates include absorption from the gut, the intact or damaged skin, and inhalation. Absorption from the gut into the bloodstream is very low. Potential hazards may exist if complexing or chelating agents are present, if absorption is continuous, or if exposure involves young animals. The intact skin provides an effective barrier to absorption of transuranics. Relatively high levels of absorption may occur when transuranics are administered subcutaneously or intramuscularly, particularly with increased acidity and solubility of the compounds. Inhalation is probably the most hazardous natural route of uptake. Insoluble transuranic compounds are retained in the lung and soluble compounds are transported rapidly via the blood to bone, liver, and other organs. Deposition of plutonium in mammalian gonads resulting in a decrease in spermatogenesis, ovarian damage, and reduced fecundity is documented. The current knowledge of the behavior of transuranics in terrestrial environments is limited. Plutonium and americium uptake by small mammals has been documented. Plutonium body burdens were related to depressed leukocyte count on a statistical basis. Reduced rodent populations in areas of high plutonium concentrations illustrate the problems of evaluating uptake by mobile animals

  13. Comparative behavior of plutonium and americium in the equatorial Pacific

    International Nuclear Information System (INIS)

    Noshkin, V.E.; Wong, K.M.; Jokela, T.A.; Brunk, J.L.; Eagle, R.J.

    1983-01-01

    Inventories of 239 + 240 Pu and 241 Am greatly in excess of global fallout levels persist in the benthic environments of Bikini and Enewetak Atolls. The amount of 239 + 240 Pu mobilized to solution at the atolls can be predicted from a distribution coefficient K/sub d/ of 2.3 x 10 5 and the mean sediment concentrations. The mobilized 239 + 240 Pu has solute-like characteristics and different valence states coexist in solution - the largest fraction of the soluble plutonium is in an oxidized form (+V,VI). The adsorption of plutonium to sediments is not completely reversible because of changes that occur in the relative amounts of the mixed oxidation states in solution with time. Characteristics of 239 + 240 Pu described at one location may not necessarily describe its behavior elsewhere. The relative amounts of 241 Am to 239 + 240 Pu may be altered in future years because of mobilization and radiological decay

  14. Molecular invariants: atomic group valence

    International Nuclear Information System (INIS)

    Mundim, K.C.; Giambiagi, M.; Giambiagi, M.S. de.

    1988-01-01

    Molecular invariants may be deduced in a very compact way through Grassman algebra. In this work, a generalized valence is defined for an atomic group; it reduces to the Known expressions for the case of an atom in a molecule. It is the same of the correlations between the fluctions of the atomic charges qc and qd (C belongs to the group and D does not) around their average values. Numerical results agree with chemical expectation. (author) [pt

  15. THE VALENCE OF CORPUSCULAR PROTEINS.

    Science.gov (United States)

    Gorin, M H; Mover, L S

    1942-07-20

    BY THE USE OF TWO EXTREME MODELS: a hydrated sphere and an unhydrated rod the valence (net charge) of corpuscular proteins can be successfully calculated from electric mobility data by the Debye-Hückel theory (modified to include the effect of the ions in the ion atmosphere) in conjunction with the electrophoretic theory of Henry. As pointed out by Abramson, this permits a comparison with values for the valence from titration data. Electrometric titration measurements of serum albumin B (Kekwick) have been determined at several ionic strengths. These results, together with the available data in the literature for serum albumin B, egg albumin, and beta-lactoglobulin have been used to compare values for the valence calculated from measurements of titration, electrophoresis, and membrane potentials. The results indicate that the usual interpretation of titration curves is open to serious question. By extrapolation of the titration data to zero ionic strength and protein concentration, there results an "intrinsic" net charge curve describing the binding of H(+) (OH(-)) ion alone. This curve agrees closely, in each case, with values of the valence calculated from mobility data (which in turn are in close accord with those estimated from membrane potential measurements). The experimental titration curves in the presence of appreciable quantities of ions and protein deviate widely from the ideal curve. It is suggested that, under these conditions, binding of undissociated acid (base) leads to erroneous values for the net charge. This binding would not affect the electrophoretic mobility. Values of the net charge obtained by the two extreme models from electrophoretic data are in agreement within 15 to 20 per cent. The agreement between the cylindrical model and the titration data is somewhat better in each case than with the sphere; i.e., this comparison enables a choice to be made between asymmetry and hydration in the interpretation of results from sedimentation and

  16. Policing plutonium: the civil liberties fallout

    International Nuclear Information System (INIS)

    Ayres, R.W.

    1975-01-01

    The most significant social cost of plutonium may be the legal problem of adjusting public safety with individual civil liberties. Safeguards to keep plutonium from criminals and terrorists will require a sacrifice of personal liberties and basic changes in the legal framework. Individuals will be denied many of the rights of privacy, expression, and association they have taken for granted. There will be a division between people associated with the nuclear industry and those outside it. Protective measures could result in a general feeling of suspicion, persecution, and distrust. If an incident should occur, the public would be caught between the perpetrators and the government, with search and seizure conditions similar to a civil war. Significant reduction of energy consumption should be imposed and all other sources of energy fully exploited or proven unworkable before undertaking a program with such consequences

  17. Use of plutonium for power production

    International Nuclear Information System (INIS)

    1965-01-01

    The panel reviewed available information on various aspects of plutonium utilization, such as physics of plutonium, technology of plutonium fuels in thermal and fast reactors, behaviour of plutonium fuel under reactor irradiation, technological and economic aspects of plutonium fuel cycle. Refs, figs and tabs

  18. Plutonium Finishing Plant. Interim plutonium stabilization engineering study

    Energy Technology Data Exchange (ETDEWEB)

    Sevigny, G.J.; Gallucci, R.H.; Garrett, S.M.K.; Geeting, J.G.H.; Goheen, R.S.; Molton, P.M.; Templeton, K.J.; Villegas, A.J. [Pacific Northwest Lab., Richland, WA (United States); Nass, R. [Nuclear Fuel Services, Inc. (United States)

    1995-08-01

    This report provides the results of an engineering study that evaluated the available technologies for stabilizing the plutonium stored at the Plutonium Finishing Plant located at the hanford Site in southeastern Washington. Further processing of the plutonium may be required to prepare the plutonium for interim (<50 years) storage. Specifically this document provides the current plutonium inventory and characterization, the initial screening process, and the process descriptions and flowsheets of the technologies that passed the initial screening. The conclusions and recommendations also are provided. The information contained in this report will be used to assist in the preparation of the environmental impact statement and to help decision makers determine which is the preferred technology to process the plutonium for interim storage.

  19. Plutonium Finishing Plant. Interim plutonium stabilization engineering study

    International Nuclear Information System (INIS)

    Sevigny, G.J.; Gallucci, R.H.; Garrett, S.M.K.; Geeting, J.G.H.; Goheen, R.S.; Molton, P.M.; Templeton, K.J.; Villegas, A.J.; Nass, R.

    1995-08-01

    This report provides the results of an engineering study that evaluated the available technologies for stabilizing the plutonium stored at the Plutonium Finishing Plant located at the hanford Site in southeastern Washington. Further processing of the plutonium may be required to prepare the plutonium for interim (<50 years) storage. Specifically this document provides the current plutonium inventory and characterization, the initial screening process, and the process descriptions and flowsheets of the technologies that passed the initial screening. The conclusions and recommendations also are provided. The information contained in this report will be used to assist in the preparation of the environmental impact statement and to help decision makers determine which is the preferred technology to process the plutonium for interim storage

  20. Chemistry of plutonium revealed

    International Nuclear Information System (INIS)

    Connick, R.E.

    1992-01-01

    In 1941 one goal of the Manhattan Project was to unravel the chemistry of the synthetic element plutonium as rapidly as possible. In this paper the work carried out at Berkeley from the spring of 1942 to the summer of 1945 is described briefly. The aqueous chemistry of plutonium is quite remarkable. Important insights were obtained from tracer experiments, but the full complexity was not revealed until macroscopic amounts (milligrams) became available. Because processes for separation from fission products were based on aqueous solutions, such solution chemistry was emphasized, particularly precipitation and oxidation-reduction behavior. The latter turned out to be unusually intricate when it was discovered that two more oxidation states existed in aqueous solution than had previously been suspected. Further, an equilibrium was rapidly established among the four aqueous oxidation states, while at the same time any three were not in equilibrium. These and other observations made while doing a crash study of a previously unknown element are reported

  1. International plutonium policy

    International Nuclear Information System (INIS)

    1978-12-01

    The need to distinguish between diversion by sub-national groups and by governments is clearly stated. The paper identifies the international safeguards measures which already exist for the handling of plutonium. It proposes that the implementation of Article XII A5 of the IAEA statute concerning the international storage of plutonium could be an important additional measure. The paper also mentions the concept of using confinement as a complimentary safeguards measure and identifies the PIPEX concept. In addition, greater use is proposed of containment and surveillance procedures. The multiplication of small reprocessing plants spread over many countries is perceived as a proliferation risk. Other means such as co-location of reprocessing and fuel fabrication facilities are relevant to diversion by sub-national groups

  2. Strategies for the plutonium utilization

    International Nuclear Information System (INIS)

    Zouain, D.M.; Lima, J.O.V.; Sakamoto, L.H.

    1981-11-01

    A review of the activities involving plutonium (its recycle, utilization and technological status and perspectives) is done. These informations are useful for an economic viability study for the plutonium utilization in thermal reactors (recycling) and in fast breeders reactor (FBR), trying to collect the major number of informations about these subjects. The initial phase describes the present status and projections of plutonium accumulation and requirements. Then, the technological process are described and some strategies are analyzed. (E.G.) [pt

  3. Plutonium in the environment

    International Nuclear Information System (INIS)

    Kudo, A.

    2001-01-01

    The first volume of the new series, Radioactivity in the Environment, focuses on the environmental occurrence, the speciation, the behaviour, the fate, the applications and the health consequences of that much-feared and much-publicised element, plutonium. Featuring a collection of selected, peer-reviewed, up-to-date papers by leading researchers in the field, this work provides a state-of-the-art description of plutonium in the environment. This title helps to explain where present frontiers are drawn in our continuing efforts to understand the science of environmental plutonium and will help to place widespread concerns into perspective. As a whole this new book series on environmental radioactivity addresses, at academic research level, the key aspects of this socially important and complex interdisciplinary subject. Presented objectively and with the ultimate authority gained from the many contributions by the world's leading experts, the negative and positive consequences of having a radioactive world around us will be documented and given perspective. refs

  4. F. Biological hazards of plutonium

    International Nuclear Information System (INIS)

    1976-01-01

    Plutonium is an unavoidable result of present nuclear power programmes. Its predominant isotopes are extremely long-lived and very toxic if absorbed in the body. In view of the increasing potential for plutonium and man to come into contact, the consequences of any plutonium release into the environment should be scientifically examined. This report is an attempt to place in one document a fully referenced account of the on-going work in many areas. There are three sections. Part 1 deals with the amounts of plutonium available in the fuel cycle, its properties and the probability of routine or accidental release. Part 2 examines the ways in which plutonium can reach man, in particular through food chains or inhalation. Part 3 details the biological effects of plutonium once it is absorbed into the body, assesses the amounts likely to be harmful and discusses the adequacy of present standards for plutonium burdens. There are two appendices. The likely differences between Pu-239, the most studied isotope, and other plutonium isotopes or transuranic nuclides are outlined in Appendix A. Appendix B contains a fuller account of the ways in which the fate of ingested or inhaled plutonium have been determined

  5. Plutonium in the marine environment

    International Nuclear Information System (INIS)

    Jarvis, N.V.; Linder, P.W.; Wade, P.W.

    1994-01-01

    The shipping of plutonium from Europe to Japan around the Cape is a contentious issue which has raised public concern that South Africa may be at risk to plutonium exposure should an accident occur. The paper describes the containers in which the plutonium (in the form of plutonium oxide, PuO 2 ) is housed and consequences of the unlikely event of these becoming ruptured. Wind-borne pollution is considered not to be a likely scenario, with the plutonium oxide particles more likely to remain practically insoluble and sediment. Plutonium aqueous and environmental chemistry is briefly discussed. Some computer modelling whereby plutonium oxide is brought into contact with seawater has been performed and the results are presented. The impact on marine organisms is discussed in terms of studies performed at marine dump sites and after the crash of a bomber carrying nuclear warheads in Thule, Greenland in 1968. Various pathways from the sea to land are considered in the light of studies done at Sellafield, a reprocessing plant in the United Kingdom. Some recent debates in the popular scientific press, such as that on the leukemia cluster at Sellafield, are described. Plutonium biochemistry and toxicity are discussed as well as medical histories of workers exposed to plutonium. 35 refs., 2 tabs., 1 fig

  6. Valence configurations in 214Rn

    International Nuclear Information System (INIS)

    Dracoulis, G.D.; Byrne, A.P.; Stuchbery, A.E.; Bark, R.A.; Poletti, A.R.

    1987-01-01

    Excited states of 214 Rn, up to spins of ≅ 24 ℎ have been studied using γ-ray and electron spectroscopy following the 208 Pb( 9 Be,3n) 214 Rn reaction. The level scheme (which differs substantially from earlier work) is compared with the results of a semi-empirical shell model calculation. The availability of high-spin orbitals for the four valence protons and two valence neutrons, and the effect of the attractive proton-neutron interaction, leads to the prediction of high-spin states at an unusually low excitation energy. Experimentally, the high level density leads to difficulties in the level scheme assignments at high spin. Nevertheless, configuration assignments, supported by transition strengths deduced from the measured lifetimes (in the nanosecond region) are suggested for the main yrast states. The decay properties also suggest that configuration mixing is important. The possibility of a gradual transition to octupole deformation, implied by the decay properties of the 11 - and 10 + yrast states is also discussed. (orig.)

  7. Plutonium oxides and uranium and plutonium mixed oxides. Carbon determination

    International Nuclear Information System (INIS)

    Anon.

    Determination of carbon in plutonium oxides and uranium plutonium mixed oxides, suitable for a carbon content between 20 to 3000 ppm. The sample is roasted in oxygen at 1200 0 C, the carbon dioxide produced by combustion is neutralized by barium hydroxide generated automatically by coulometry [fr

  8. Plutonium interactions with soil microbial metabolites: effect on plutonium sorption by soil

    International Nuclear Information System (INIS)

    Wildung, R.E.; Garland, T.R.; Rogers, J.E.

    1987-01-01

    To develop an understanding of the mechanisms of plutonium (Pu) complexation and solubilization by soil microorganisms, a broad range of bacteria and fungi were isolated in pure cultures from soil on the basis of metal tolerance and carbon requirements. The organisms were then used in investigations to examine Pu cellular transport, Pu complexation by extracellular metabolites, and the effects of complexation on Pu valence state, chemical form, and solubility in soil. Of the 239 bacteria and 250 fungi isolated from soil, 19 bacteria and 60 fungi were selected for detailed study. Of these organisms, 15 bacteria and 18 fungi grew to form extracellular Pu complexes that increased the concentration of Pu in soil column eluates relative to controls. Elution through soil effectively removed positively charged Pu complexes. Increased Pu mobility in soil resulted from the formation of neutral and negatively charged Pu complexes, which differed with organism type. In the presence of known microbial metabolites and synthetic ligands (DTPA, EDTA, EDDHA), Pu(VI) was reduced to Pu(IV) before complexation, suggesting that Pu(IV) would be the dominant valence state associated with organic complexes in soils. Studies on selected organisms indicated that both active Pu transport and Pu sorption on the cell occurred, and these phenomena, as well as complexation by extracellular metabolites of Pu, were a function of the form of Pu supplied, the organism type and growth characteristics, and the ability of the organism to alter extracellular pH. 18 references, 6 figures, 7 tables

  9. High-temperature enthalpies of plutonium monocarbide and plutonium sesquicarbide

    International Nuclear Information System (INIS)

    Oetting, F.L.

    1979-01-01

    The high-temperature enthalpies of plutonium monocarbide and plutonium sesquicarbide have been determined with a copper-block calorimeter of the isoperibol type. The experimental enthalpy data, which was measured relative to 298 K, covered the temperature range from 400 to 1500 K. The calculation of the temperature rise of the calorimeter takes into account the added heat evolution from the radioactive decay of the plutonium samples. These enthalpy results, combined with the heat capacity and entropy of the respective carbide at 298 K available from the literature, has made it possible to generate tables of thermodynamic functions for the plutonium carbides. The behavior of the heat capacity of both of the plutonium carbides, i.e., a relatively steep increase in the heat capacity as the temperature increases, may be attributed to a premelting effect with the formation of vacancies within the crystal lattice although a theoretical treatment of this phenomenon is not given

  10. Determination of plutonium in environment

    International Nuclear Information System (INIS)

    Sakanoue, Masanobu

    1978-01-01

    Past and present methods of determining the amount of plutonium in the environment are summarized. Determination of the amount of plutonium in uranium ore began in 1941. Plutonium present in polluted environments due to nuclear explosions, nuclear power stations, etc. was measured in soil and sand in Nagasaki in 1951 and in ash in Bikini in 1954. Analytical methods of measuring the least amount of plutonium in the environment were developed twenty years later. Many studies on and reviews of these methods have been reported all over the world, and a standard analytical procedure has been adopted. A basic analytical method of measurement was drafted in Japan in 1976. The yield, treatment of samples, dissolution, separation, control of measurable ray sources determination by α spectrometry, cross-check determination, and treatment of samples containing hardly soluble plutonium were examined. At present, the amount of plutonium can be determined by all of these methods. The presence of plutonium was studied further, and the usefulness of determination of the plutonium isotope ratio is discussed. (Kumagai, S.)

  11. Work surface for soluble plutonium

    International Nuclear Information System (INIS)

    Silver, G.L.

    2005-01-01

    A three-dimensional work surface for aqueous plutonium is illustrated. It is constructed by means of estimating work as a function of the ambient pH and redox potential in a plutonium solution. The surface is useful for illustrating the chemistry of disproportionation reactions. Work expressions are easier to use than work integrals. (author)

  12. The economics of plutonium recycle

    International Nuclear Information System (INIS)

    James, R.A.

    1977-11-01

    The individual cost components and the total fuel cycle costs for natural uranium and uranium-plutonium mixed oxide fuel cycles for CANDU-PHW reactors are discussed. A calculation is performed to establish the economic conditions under which plutonium recycle would be economically attractive. (auth)

  13. Plutonium Round Robin Test

    International Nuclear Information System (INIS)

    Dudder, G.B.; Herbillon, G.H.

    2001-01-01

    Full text: The goal of nuclear forensics is to develop a preferred approach to illicit trafficking investigations. This approach must be widely understood and acceptable as credible. The principle objectives of the Round Robin Test are to prioritize the forensic techniques and methods, evaluate attribution capabilities, and examine the utility of database. The Plutonium Round Robin has made a tremendous contribution to fulfilling these goals through a collaborative learning experience that resulted from the outstanding efforts of the six participating international laboratories. A prioritize list of techniques and methods has been developed based on this exercise. Future work will focus on a Highly Enriched Round Robin and extent to which the techniques and methods can be generalized. The Plutonium Round Robin demonstrated a rather high level of capability to determine the important characteristics of the materials and processes using analytical methods. When this capability to was combined with the appropriate knowledge and database, it resulted in a demonstrated capability to attribute the source of the materials to a specific nuclear fuel, reactor, and reprocessing facility. A number of shortfalls were also identified in our current capabilities. These included alternative dating techniques. Light Water Reactor discrimination techniques, and the lack of a comprehensive network of data/knowledge bases. The result of the Round Robin will be used to develop guidelines or a 'recommended protocol' to be made available to the interested authorities and countries to use in real cases. The poster will present a summary of the results of the Plutonium Round Robin and describe the plans the subsequent Highly Enriched Uranium Round Robin Test. (author)

  14. Solvent anode for plutonium purification

    International Nuclear Information System (INIS)

    Bowersox, D.F.; Fife, K.W.; Christensen, D.C.

    1986-01-01

    The purpose of this study is to develop a technique to allow complete oxidation of plutonium from the anode during plutonium electrorefining. This will eliminate the generation of a ''spent'' anode heel which requires further treatment for recovery. Our approach is to employ a solvent metal in the anode to provide a liquid anode pool throughout electrorefining. We use molten salts and metals in ceramic crucibles at 700 0 C. Our goal is to produce plutonium metal at 99.9% purity with oxidation and transfer of more than 98% of the impure plutonium feed metal from the anode into the salt and product phases. We have met these criteria in experiments on the 100 to 1000 g scale. We plan to scale our operations to 4 kg of feed plutonium and to optimize the process parameters

  15. Using Biomolecules to Separate Plutonium

    Science.gov (United States)

    Gogolski, Jarrod

    Used nuclear fuel has traditionally been treated through chemical separations of the radionuclides for recycle or disposal. This research considers a biological approach to such separations based on a series of complex and interdependent interactions that occur naturally in the human body with plutonium. These biological interactions are mediated by the proteins serum transferrin and the transferrin receptor. Transferrin to plutonium in vivo and can deposit plutonium into cells after interacting with the transferrin receptor protein at the cell surface. Using cerium as a non-radioactive surrogate for plutonium, it was found that cerium(IV) required multiple synergistic anions to bind in the N-lobe of the bilobal transferrin protein, creating a conformation of the cerium-loaded protein that would be unable to interact with the transferrin receptor protein to achieve a separation. The behavior of cerium binding to transferrin has contributed to understanding how plutonium(IV)-transferrin interacts in vivo and in biological separations.

  16. Cycle downstream: the plutonium question

    International Nuclear Information System (INIS)

    Zask, G.; Rome, M.; Delpech, M.

    1998-01-01

    This day, organized by the SFEN, took place at Paris the 4 june 1998. Nine papers were presented. They take stock on the plutonium physics and its utilization as a nuclear fuel. This day tried to bring information to answer the following questions: do people have to keep the plutonium in the UOX fuel or in the MOX fuel in order to use it for future fast reactors? Do people have to continue obstinately the plutonium reprocessing in the MOX for the PWR type reactors? Will it be realized a underground disposal? Can it be technically developed plutonium incinerators and is it economically interesting? The plutonium physics, the experimental programs and the possible solutions are presented. (A.L.B.)

  17. Plutonium storage study

    International Nuclear Information System (INIS)

    1979-01-01

    This Spanish study gives a more detailed analysis of a possible store for plutonium oxide. The capacity of the store is assumed to be 30 t Pu and the minimum storage time 2 years. The study includes a general description of the store and its design philosophy; comments on the quality and properties of the material stored; a detailed criticality study and comments on gas and heat generation and shielding requirements; and a brief cost evaluation. Costs are estimated to be about $110/kg PuO 2 /year

  18. Speciation of the plutonium at trace levels by capillary electrophoresis-ICP-MS coupling

    International Nuclear Information System (INIS)

    Ambard, Ch.

    2007-01-01

    The CE-ICP-MS coupling allowed the development of new analytical methods for the study of plutonium speciation at trace levels including complexation studies of this element by organic and inorganic ligands. First, a method, called dual detection, based on the simultaneous use of the UV-Visible spectrophotometer integrated in the capillary electrophoresis and the ICPMS was developed and validated. It allows the unambiguous determination of electrophoretic mobilities for separated chemical species and gives a powerful tool for speciation studies. Then, the influence on plutonium redox speciation of the buffer from the background electrolyte was evaluated. This study showed the implications of the electrolyte constituents' choice on plutonium redox equilibrium in the sample. Furthermore, the CE-ICP-MS coupling was used for studying the plutonium complexation at trace levels by some organic (NTA and DTPA) and inorganic ligands (carbonates). The behaviour of plutonium valence +III, +IV and +VI was studied in the presence of buffer at near neutral pH. Different species of plutonium were observed depending on the initial oxidation state of the plutonium. This study showed the potential of poly-amino-carboxylic acids, such as NTA and DTPA, for dissolving plutonium precipitates, regardless its initial speciation. Finally, the carbonation of pentavalent neptunium, as an analogue of Pu(V), was achieved at very low concentration of Np (10 -8 mol.L -1 ). The formation constant of NpO 2 (CO 3 )- at 25 deg. C and 2,5 x 10 -2 mol.L -1 ionic strength was measured by CE-ICP-MS and found to be consistent with literature data. (author)

  19. The toxicity of plutonium

    International Nuclear Information System (INIS)

    Ramsden, D.; Johns, T.F.

    1977-01-01

    Reference is made to recent publications concerned with the radiotoxicity of inhaled insoluble Pu compounds. The publications are a paper by Thorne and Vennart (Nature 263:555 (1976)), a report entitled 'The Toxicity of Plutonium', (London (HMSO), 1975), and the 'Sixth Report of the Royal Commission on Environmental Pollution', (Cmnd. 6618, London (HMSO), 1976). Thorne and Vennart concluded that the previously accepted value for the maximum permissible annual intake (MPAI) of such compounds may be too high by a factor of about five, and a similar conclusion was reached in the other two publications. It is thought by the present authors that the methods which have been used to suggest new values for the MPAI are unduly pessimistic for high-fired PuO 2 ; calculations have been based on the lung model of ICRP Publication 19 'The Metabolism of Compounds of Plutonium and the Other Actinides', (International Commission of Radiological Protection, 1972). This involves concluding that the risks to bone and liver are comparable to those for lung. This is discussed and it is thought that the previously established idea that the lung is the critical organ remains substantially correct for the case of high-fired PuO 2 . (U.K.)

  20. Plutonium oxide dissolution

    International Nuclear Information System (INIS)

    Gray, J.H.

    1992-01-01

    Several processing options for dissolving plutonium oxide (PuO 2 ) from high-fired materials have been studied. The scoping studies performed on these options were focused on PuO 2 typically generated by burning plutonium metal and PuO 2 produced during incineration of alpha contaminated waste. At least two processing options remain applicable for dissolving high-fired PuO 2 in canyon dissolvers. The options involve solid solution formation of PuO 2 With uranium oxide (UO 2 ) and alloying incinerator ash with aluminum. An oxidative dissolution process involving nitric acid solutions containing a strong oxidizing agent, such as cerium (IV), was neither proven nor rejected. This uncertainty was due to difficulty in regenerating cerium (IV) ions during dissolution. However, recent work on silver-catalyzed dissolution of PuO 2 with persulfate has demonstrated that persulfate ions regenerate silver (II). Use of persulfate to regenerate cerium (IV) or bismuth (V) ions during dissolution of PuO 2 materials may warrant further study

  1. The development and testing of the new flowsheets for the plutonium purification of the Purex process

    Energy Technology Data Exchange (ETDEWEB)

    Bugrov, K.V.; Korotaev, V.G.; Korchenkin, K.K.; Logunov, M.V.; Ludin, S.A.; Mashkin, A.N.; Melentev, A.B.; Samarina, N.S. [FSUE ' PAMayak' , Lenin st., 35, Ozersk 456780 (Russian Federation)

    2016-07-01

    In order to improve the extraction flowsheet of RT-1 Plant two versions of plutonium purification unit flowsheet were developed: a flowsheet with stabilization of Pu(IV)-Np(IV) valence pair and Pu, Np co-recovery, and a flowsheet with stabilization of Pu(IV)-Np(V) valence pair and Pu recovery. The task related to stabilization of the valence pair of the target components in the required state was solved with the use of reactants already applied at RT-1 Plant, namely, hydrogen peroxide, hydrazine nitrate and catalyst (Fe). Both flowsheets were adapted for the plant purification facility with minimum modifications of the equipment, and passed the full scale industrial testing. As a result of this work, reduction in volume and salt content of the raffinate was achieved. (authors)

  2. Hazards of plutonium and fuel reprocessing

    International Nuclear Information System (INIS)

    Watson, G.M.

    1978-01-01

    Apart from the possibility that civil plutonium may be diverted to military use the main argument against the introduction of a plutonium economy seems to be the supposedly unmanageable biological risk attached to plutonium itself. The author points out weaknesses in many of the opponents' arguments against the increased use of plutonium and argues that current safety practices are more than adequate in handling plutonium and other radioactive materials

  3. Recovery of plutonium by pyroredox processing

    International Nuclear Information System (INIS)

    McNeese, J.A.; Bowersox, D.F.; Christensen, D.C.

    1985-09-01

    Using pyrochemical oxidation and reduction, we have developed a process to recover the plutonium in impure scrap with less than 95% plutonium. This plutonium metal was further purified by pyrochemical electrorefining. During development of the procedures, depleted electrorefining anodes were processed, and over 80% of the plutonium was recovered as high-purity metal in one electrorefining cycle. Over 40 kg of plutonium has been recovered from 55 kg of impure anodes with our procedures. 6 refs., 7 figs., 4 tabs

  4. Recovery of plutonium by pyroredox processing

    International Nuclear Information System (INIS)

    McNeese, J.A.; Bowersox, D.F.; Christensen, D.C.

    1985-01-01

    Using pyrochemical oxidation and reduction, we have developed a process to recover the plutonium in impure scrap with less than 95% plutonium. This plutonium metal was further purified by pyrochemical electrorefining. During development of the procedures, depleted electrorefining anodes were processed, and over 80% of the plutonium was recovered as high-purity metal in one electrorefining cycle. Over 40 kg of plutonium has been recovered from 55 kg of impure anodes with our procedures. 6 refs., 2 figs., 5 tabs

  5. A method for the gravimetric determination of plutonium in pure plutonium nitrate concentrate solution

    International Nuclear Information System (INIS)

    Mair, M.A.; Savage, D.J.

    1986-12-01

    Plutonium nitrate solution is treated with sulphuric acid before being heated and finally ignited. The stoichiometric plutonium dioxide so formed is weighed and hence the plutonium content is calculated. (author)

  6. Plutonium contaminated materials research programme

    International Nuclear Information System (INIS)

    Higson, S.G.

    1986-01-01

    The paper is a progress report for 1985 from the Plutonium Contaminated Materials Working Party (PCMWP). The PCMWP co-ordinates research and development on a national basis in the areas of management, treatment and immobilisation of plutonium contaminated materials, for the purpose of waste management. The progress report contains a review of the development work carried out in eight areas, including: reduction of arisings, plutonium measurement, sorting and packaging, washing of shredded combustible PCM, decommissioning and non-combustible PCM treatment, PCM immobilisation, treatment of alpha bearing liquid wastes, and engineering objectives. (UK)

  7. Plutonium again (smuggling and movements)

    International Nuclear Information System (INIS)

    Anon.

    1994-01-01

    A link is discounted between nuclear proliferation and the recently discovered smuggled plutonium from the former Soviet Union at Munich airport and other places in Germany. It is argued that governments wishing to obtain nuclear materials to develop a weapons programme would not arrange to have it smuggled in a suitcase. Instead, it is speculated that a link exists between the plutonium smuggling incidents and the desire to promote the production of mixed oxide (MOX) fuel. Such incidents, by further raising public anxiety, may be intended to turn public opinion in favour of MOX fuel production as a sensible way of getting rid of surplus plutonium. (UK)

  8. Learning more about plutonium; En savoir plus sur le plutonium

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2008-07-01

    This digest brochure explains what plutonium is, where it comes from, how it is used, its recycling into Mox fuel, its half life, historical discovery, its presence in the environment, toxicity and radioactivity. (J.S.)

  9. Radiolysis of aqueous solution of plutonium; Radiolyse des solutions aqueuses de plutonium

    Energy Technology Data Exchange (ETDEWEB)

    Pages nee Flon, M [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1960-07-01

    This study is concerned first with the effects of gamma rays on plutonium aqueous solutions at various valency states, in presence of sulfuric, perchloric, nitric and hydrochloric acids. The main feature is the reduction of Pu VI into Pu V, followed by dismutation from V to IV and VI. For sulfuric and perchloric acid solutions (0,2 N) the following process is given: radiolysis of water produces OH, H{sub 2}O{sub 2}, H and H{sub 2}. H and H{sub 2}O{sub 2} reduce Pu VI while Pu V is oxidised by OH radicals. However the reaction of hydrogen peroxide is slow and leads to an after effect. A parallel study of the action of H{sub 2}O{sub 2} has given a confirmation. Spectrophotometric measurements were carried out on disappearance of Pu VI and formation of Pu IV and it was possible to make determination of G{sub H{sub 2}}{sub O{sub 2}} = 0,8 and G{sub H} - G{sub OH} = 0,8. G{sub H{sub 2}} = 0,41 was measured by gas analysis. The calculation of G{sub {sup -}}{sub H{sub 2}}{sub O} gave 4,35. The re-oxidation of Pu V is dependant on the concentration of sulfate ions. In perchloric acid solution reduction goes on to Pu Ill. Cl{sup -} and NO{sub 3}{sup -} ions inhibit the reduction and even suppress it. The effect of alpha particles both from plutonium and from polonium is very similar to the effect of hydrogen peroxyde. Induction time were observed mainly in presence of HSO{sub 4}{sup -}, depending on the accumulation of H{sub 2}O{sub 2} and (or) of plutonium peroxide. At low acidities, Pu IV peroxide seems to lead to polymer forms. In the more simple cases (H{sub 2}SO{sub 4} and HClO{sub 4} 0,2N), the following yields were found: G (equivalent reduced) = 3.2, G{sub H{sub 2}}{sub O{sub 2}} = 1.35, G{sub H{sub 2}} = 1.6 and G{sub H} - G{sub OH} = 0.1, assuming G{sub HO{sub 2}} = 0.2; and the usual hypothesis on radiolysis of water by alpha particles. Radiation induced oxidation of Pu III into Pu IV was also observed in H{sub 2}SO{sub 4} and HNO{sub 3} aqueous solutions, and

  10. Simultaneous conditioning of valence and arousal.

    Science.gov (United States)

    Gawronski, Bertram; Mitchell, Derek G V

    2014-01-01

    Evaluative conditioning (EC) refers to the change in the valence of a conditioned stimulus (CS) due to its pairing with a positive or negative unconditioned stimulus (US). To the extent that core affect can be characterised by the two dimensions of valence and arousal, EC has important implications for the origin of affective responses. However, the distinction between valence and arousal is rarely considered in research on EC or conditioned responses more generally. Measuring the subjective feelings elicited by a CS, the results from two experiments showed that (1) repeated pairings of a CS with a positive or negative US of either high or low arousal led to corresponding changes in both CS valence and CS arousal, (2) changes in CS arousal, but not changes in CS valence, were significantly related to recollective memory for CS-US pairings, (3) subsequent presentations of the CS without the US reduced the conditioned valence of the CS, with conditioned arousal being less susceptible to extinction and (4) EC effects were stronger for high arousal than low arousal USs. The results indicate that the conditioning of affective responses can occur simultaneously along two independent dimensions, supporting evidence in related areas that calls for a consideration of both valence and arousal. Implications for research on EC and the acquisition of emotional dispositions are discussed.

  11. Valence instabilities in cerium intermetallics

    International Nuclear Information System (INIS)

    Dijkman, W.H.

    1982-01-01

    The primary purpose of this investigation was to study the magnetic behaviour of cerium in intermetallic compounds, that show an IV behaviour, e.g. CeSn 3 . In the progress of the investigations, it became of interest to study the effect of changes in the lattice of the IV compound by substituting La or Y for Ce, thus constituting the Cesub(1-x)Lasub(x)Sn 3 and Cesub(1-x)Ysub(x)Sn 3 quasibinary systems. A second purpose was to examine the possibility of introducing instabilities in the valency of a trivalent intermetallic cerium compound: CeIn 3 , also by La and Y-substitutions in the lattice. Measurements on the resulting Cesub(1-x)Lasub(x)In 3 and Cesub(1-x)Ysub(x)In 3 quasibinaries are described. A third purpose was to study the (gradual) transition from a trivalent cerium compound into an IV cerium compound. This was done by examining the magnetic properties of the CeInsub(x)Snsub(3-x) and CePbsub(x)Snsub(3-x) systems. Finally a new possibility was investigated: that of the occurrence of IV behaviour in CeSi 2 , CeSi, and in CeGa 2 . (Auth.)

  12. Plutonium waste container identification

    International Nuclear Information System (INIS)

    Schmierer, T.J.

    1979-01-01

    The purpose of this paper is to define the parameters of a method for identifying plutonium waste containers. This information will form the basis for a permanent committee to develop a complete identification program for use throughout the world. Although a large portion of the information will be on handwritten notebooks and may not be as extensive as is desired, it will all be helpful. The final information will be programmed into computer language and be available to all interested parties as well as a central control committee which will have the expertise to provide each government with advice on the packaging, storage, and measurement of the waste for which it is responsible. As time progresses, this central control committee should develop permanent storage sites and establish a system of records which will last for hundreds of years

  13. Uranium plutonium oxide fuels

    International Nuclear Information System (INIS)

    Cox, C.M.; Leggett, R.D.; Weber, E.T.

    1981-01-01

    Uranium plutonium oxide is the principal fuel material for liquid metal fast breeder reactors (LMFBR's) throughout the world. Development of this material has been a reasonably straightforward evolution from the UO 2 used routinely in the light water reactor (LWR's); but, because of the lower neutron capture cross sections and much lower coolant pressures in the sodium cooled LMFBR's, the fuel is operated to much higher discharge exposures than that of a LWR. A typical LMFBR fuel assembly is shown. Depending on the required power output and the configuration of the reactor, some 70 to 400 such fuel assemblies are clustered to form the core. There is a wide variation in cross section and length of the assemblies where the increasing size reflects a chronological increase in plant size and power output as well as considerations of decreasing the net fuel cycle cost. Design and performance characteristics are described

  14. The plutonium ban

    International Nuclear Information System (INIS)

    Anon.

    1977-01-01

    'Nuclear Power Issues and Choices' is the title of a recent report which has been performed by a study group sponsored by the Ford Foundation and administered by the MITRE Corporation. The main concern of this study is to prevent the proliferation of nuclear weapons. Since the reprocessing of spent fuel elements yields among others plutonium of bomb quality, the report of the Ford Foundation comes to the conclusion that the USA should defer the closing of the fuel cycle, defer the reprocessing of spent nuclear fuel, deposit the spent fuel elemenets as a whole, and defer the breeder which can not run without fuel reprocessing. The German attitude however is that we can not relinquish on reprocessing and recycling of nuclear fuel because we are lacking such rich resources of coal, oil and uranium as the USA have. Furthermore, the deposition of spent fuel elements may be more dangerous than the deposition of the radioactive waste from reprocessing plants. (orig.) [de

  15. Valence evaluation with approaching or withdrawing cues: directly testing valence-arousal conflict theory.

    Science.gov (United States)

    Wang, Yan Mei; Li, Ting; Li, Lin

    2017-07-19

    The valence-arousal conflict theory assumes that both valence and arousal will trigger approaching or withdrawing tendencies. It also predicts that the speed of processing emotional stimuli will depend on whether valence and arousal trigger conflicting or congruent motivational tendencies. However, most previous studies have provided evidence of the interaction between valence and arousal only, and have not provided direct proof of the interactive links between valence, arousal and motivational tendencies. The present study provides direct evidence for the relationship between approach-withdrawal tendencies and the valence-arousal conflict. In an empirical test, participants were instructed to judge the valence of emotional words after visual-spatial cues that appeared to be either approaching or withdrawing from participants. A three-way interaction (valence, arousal, and approach-withdrawal tendency) was observed such that the response time was shorter if participants responded to a negative high-arousal stimulus after a withdrawing cue, or to a positive low-arousal stimulus after an approaching cue. These findings suggest that the approach-withdrawal tendency indeed plays a crucial role in valence-arousal conflict, and that the effect depends on the congruency of valence, arousal and tendency at an early stage of processing.

  16. Ab initio valence calculations in chemistry

    CERN Document Server

    Cook, D B

    1974-01-01

    Ab Initio Valence Calculations in Chemistry describes the theory and practice of ab initio valence calculations in chemistry and applies the ideas to a specific example, linear BeH2. Topics covered include the Schrödinger equation and the orbital approximation to atomic orbitals; molecular orbital and valence bond methods; practical molecular wave functions; and molecular integrals. Open shell systems, molecular symmetry, and localized descriptions of electronic structure are also discussed. This book is comprised of 13 chapters and begins by introducing the reader to the use of the Schrödinge

  17. On triangle meshes with valence dominant vertices

    KAUST Repository

    Morvan, Jean-Marie

    2018-01-01

    We study triangulations $\\cal T$ defined on a closed disc $X$ satisfying the following condition: In the interior of $X$, the valence of all vertices of $\\cal T$ except one of them (the irregular vertex) is $6$. By using a flat singular Riemannian metric adapted to $\\cal T$, we prove a uniqueness theorem when the valence of the irregular vertex is not a multiple of $6$. Moreover, for a given integer $k >1$, we exhibit non isomorphic triangulations on $X$ with the same boundary, and with a unique irregular vertex whose valence is $6k$.

  18. On triangle meshes with valence dominant vertices

    KAUST Repository

    Morvan, Jean-Marie

    2018-02-16

    We study triangulations $\\\\cal T$ defined on a closed disc $X$ satisfying the following condition: In the interior of $X$, the valence of all vertices of $\\\\cal T$ except one of them (the irregular vertex) is $6$. By using a flat singular Riemannian metric adapted to $\\\\cal T$, we prove a uniqueness theorem when the valence of the irregular vertex is not a multiple of $6$. Moreover, for a given integer $k >1$, we exhibit non isomorphic triangulations on $X$ with the same boundary, and with a unique irregular vertex whose valence is $6k$.

  19. Plutonium-related work and cause-specific mortality at the United States Department of Energy Hanford Site.

    Science.gov (United States)

    Wing, Steve; Richardson, David; Wolf, Susanne; Mihlan, Gary

    2004-02-01

    Health effects of working with plutonium remain unclear. Plutonium workers at the United States Department of Energy (US-DOE) Hanford Site in Washington State, USA were evaluated for increased risks of cancer and non-cancer mortality. Periods of employment in jobs with routine or non-routine potential for plutonium exposure were identified for 26,389 workers hired between 1944 and 1978. Life table regression was used to examine associations of length of employment in plutonium jobs with confirmed plutonium deposition and with cause specific mortality through 1994. Incidence of confirmed internal plutonium deposition in all plutonium workers was 15.4 times greater than in other Hanford jobs. Plutonium workers had low death rates compared to other workers, particularly for cancer causes. Mortality for several causes was positively associated with length of employment in routine plutonium jobs, especially for employment at older ages. At ages 50 and above, death rates for non-external causes of death, all cancers, cancers of tissues where plutonium deposits, and lung cancer, increased 2.0 +/- 1.1%, 2.6 +/- 2.0%, 4.9 +/- 3.3%, and 7.1 +/- 3.4% (+/-SE) per year of employment in routine plutonium jobs, respectively. Workers employed in jobs with routine potential for plutonium exposure have low mortality rates compared to other Hanford workers even with adjustment for demographic, socioeconomic, and employment factors. This may be due, in part, to medical screening. Associations between duration of employment in jobs with routine potential for plutonium exposure and mortality may indicate occupational exposure effects. Copyright 2004 Wiley-Liss, Inc.

  20. Differential spectrophotometric determination of plutonium

    International Nuclear Information System (INIS)

    Lecat, J.

    1980-01-01

    Differential spectrophotometric method is used for determination of plutonium reduced to oxydation state III+ by ascorbic acid, at 560 nm. Concentration of solutions is 4 g/l and accuracy of the method is better than 0,3% [fr

  1. The first milligrams of plutonium

    International Nuclear Information System (INIS)

    Goldschmidt, B.

    1996-01-01

    This paper relates the discovery of the different plutonium chemical extraction processes in their historical context. The first experiments started during the second world war in 1942 with the American ''Metallurgical Laboratory'' project which brought together Arthur Compton, Enrico Fermi and Glenn Seaborg. During the same period, a competitive English-Canadian project, the ''Montreal Project'', was carried out to test different plutonium solvent extraction techniques. The author participated in both projects and joined the CEA in 1946, where he was in charge of the uranium and plutonium chemistry. By the end of 1949, his team could isolate the first milligrams of French plutonium from uranium oxide pellets of the ZOE reactor. In the beginning of 1952 he developed with his team the PUREX process. (J.S.)

  2. Technological alternatives for plutonium transport

    International Nuclear Information System (INIS)

    1978-12-01

    This paper considers alternative transport modes (air, sea, road, rail) for moving (1) plutonium from a reprocessing plant to a store or a fuel fabrication facility, and (2) MOX fuel from the latter to a reactor. These transport modes and differing forms of plutonium are considered in terms of: their proliferation resistance and safeguards; environmental and safety aspects; and economic aspects. It is tentatively proposed that the transport of plutonium could continue by air or sea where long distances are involved and by road or rail over shorter distances; this would be acceptable from the non-proliferation, environmental impact and economic aspects - there may be advantages in protection if plutonium is transported in the form of mixed oxide

  3. Plutonium helps probe protein, superconductor

    International Nuclear Information System (INIS)

    Anon.

    1990-01-01

    Scientists are finding that plutonium can be a useful research tool that may help them answer important questions in fields as diverse as biochemistry and solid-state physics. This paper reports that U.S. research involving plutonium is confined to the Department of Energy's national laboratories and centers around nuclear weapons technology, waste cleanup and disposal, and health effects. But at Los Alamos National Laboratory, scientists also are using plutonium to probe the biochemical behavior of calmodulin, a key calcium-binding protein that mediates calcium-regulated processes in biological systems. At Argonne National Laboratory, another team is trying to learn how a superconductor's properties are affected by the 5f electrons of an actinide like plutonium

  4. An alternative plutonium disposition method

    International Nuclear Information System (INIS)

    Kueppers, C.

    2002-01-01

    This paper provides a feasibility study on vitrification of plutonium with high active waste concentrate, and fabrication of MOX fuel rods for direct final disposal. These are potential alternatives to the direct use of MOX fuel in a reactor. (author)

  5. Chloride removal from plutonium alloy

    International Nuclear Information System (INIS)

    Holcomb, H.P.

    1983-01-01

    SRP is evaluating a program to recover plutonium from a metallic alloy that will contain chloride salt impurities. Removal of chloride to sufficiently low levels to prevent damaging corrosion to canyon equipment is feasible as a head-end step following dissolution. Silver nitrate and mercurous nitrate were each successfully used in laboratory tests to remove chloride from simulated alloy dissolver solution containing plutonium. Levels less than 10 ppM chloride were achieved in the supernates over the precipitated and centrifuged insoluble salts. Also, less than 0.05% loss of plutonium in the +3, +4, or +6 oxidation states was incurred via precipitate carrying. These results provide impetus for further study and development of a plant-scale process to recover plutonium from metal alloy at SRP

  6. Inhaled plutonium oxide in dogs

    International Nuclear Information System (INIS)

    Anon.

    1981-01-01

    This project is concerned with long-term experiments to determine the life-span dose-effect relationships of inhaled 239 PuO 2 and 238 PuO 2 in beagles. The data will be used to estimate the health effects of inhaled transuranics. The tissue distribution of plutonium, radiation effects in the lung and hematologic changes in plutonium-exposed beagles with lung tumors were evaluated

  7. Plutonium contamination in italian population

    International Nuclear Information System (INIS)

    Cave-Bondi, G.; Merli, S.; Rogo, M.; Sgarbazzini, M.; Clemente, G.F.; Mancini, L.; Santori, G.; Tardella, Q.

    1983-01-01

    The literature data concerning the biological and the chemical physical characteristics of plutonium are summarized in the first part of the paper. The experimental results of the plutonium concentration in complete diets, single food items and some human autopsy tissues, regarding the Italian situation, are then presented and discussed. Our experimental data are in good agreement with similar data reported in several studies carried out in some countries of the north emisphere

  8. Plutonium: real and false problems

    International Nuclear Information System (INIS)

    Bemden, E. van den

    1981-01-01

    This paper deals with technical and technological state of the possibilities of using plutonium as fuel in the thermal and fast reactors. It also describes the political blockage restraining its use and the reasons for it. The accent is put on some fundamental lacks of international coordination and on some problems of commercial policy, which impede, in a certain way, the industrial use of plutonium as a fuel. (author)

  9. Monitoring the risks of plutonium

    International Nuclear Information System (INIS)

    Holliday, B.

    1978-01-01

    The difficulties in monitoring the environment in work areas where plutonium is handled are identified and both continuous and personal air sampling techniques considered. Methods of estimating the amounts of plutonium retained in the body are: (1) Direct external counting over the chest of the 'soft' low energy X-rays and gamma rays emitted by the plutonium deposited in the lungs. (2) Measuring plutonium excreted in urine. (3) Analysing faeces soon after a suspected contamination. Limitation of these techniques are discussed and it is shown that estimating the amount of plutonium in the body, or a specific organ, is extremely difficult, both because of the lack of sensitivity of the measuring techniques (especially chest scanning) and because of the problems in interpreting data, stemming from a lack of knowledge of crucial characteristics of the inhaled plutonium (such as particle size and solubility). Nevertheless it is felt that the judicious integration of all the options creates a level of certainty that no individual technique can possibly inspire. (U.K.)

  10. Atomic energy policy of Japan, especially plutonium utilization policy

    International Nuclear Information System (INIS)

    Moriguchi, Y.

    1993-01-01

    The necessity of plutonium use in Japan is discussed. Basic policy regarding plutonium use and future plutonium utilization programme is described including such an aspect as management of plutonium from dismantled nuclear weapons

  11. Valence nucleons in self-consistent fields

    International Nuclear Information System (INIS)

    Di Toro, M.; Lomnitz-Adler, J.

    1978-01-01

    An iterative approach to determine directly the best Hartree-Fock one-body density rho is extended by expressing rho in terms of a core and a valence part and allowing for general crossings of occupied and unoccupied levels in the valence part. Results are shown for 152 Sm and a microscopic analysis of the core structure of deformed light nuclei is carried out. (author)

  12. Theory for the mixed-valence state

    International Nuclear Information System (INIS)

    Varma, C.M.

    1979-01-01

    A theory is presented which explains why mixed-valence compounds behave as two component Fermi liquids, and why TmSe orders magnetically while the other known mixed-valence compounds do not. The variation of Tsub(N) and the field Hsub(T) to obtain ferromagnetic alignment with changing Tm 2+ /Tm 3+ ratio is quantitatively explained. For Tm 2+ concentration > = 0.3, TmSe is predicted to order ferromagnetically

  13. Plutonium re-cycle in HTR

    Energy Technology Data Exchange (ETDEWEB)

    Desoisa, J. A.

    1974-03-15

    The study of plutonium cycles in HTRs using reprocessed plutonium from Magnox and AGR fuel cycles has shown that full core plutonium/uranium loadings are in general not feasible, burn-up is limited due the need for lower loadings of plutonium to meet reload core reactivity limits, on-line refueling is not practicable due to the need for higher burnable poison loadings, and low conversion rates in the plutonium-uranium cycles cannot be mitigated by axial loading schemes so that fissile make-up is needed if HTR plutonium recycle is desired.

  14. Erosional losses of fallout plutonium

    International Nuclear Information System (INIS)

    Foster, G.R.; Hakonson, T.E.

    1987-01-01

    Plutonium from fallout after atmospheric explosion of nuclear weapons in the 1950's and 1960s is being redistributed over the landscape by soil erosion and carried on sediment by streams to oceans. Erosion rates computed with the Universal Soil Loss Equation for more than 200,000 sample points on nonfederal land across the US were used to estimate plutonium removal rates by soil erosion. On the average, only about 4% of the eroded sediment reaches the outlet of a major river. The remaining sediment is deposited en route, and because deposition is a selective process, the sediment is enriched in fine particles having the highest concentration of plutonium because of the element's strong association with clay and silt-sized sediment. Estimated enrichment ratios, sediment delivery ratios, and erosion rates were used to estimate annual delivery of fallout plutonium. These estimates ranged from 0.002% of the initial fallout plutonium inventory for the Savannah River basin to 0.01% for the Columbia River basin, to 0.02% for the Hudson and Rio Grande River basins, to 0.08% for the Mississippi River basin. If the deposition of plutonium had been uniformly 1 mCi/km 2 , the estimated plutonium activity on suspended sediment would range from about 7 fCi/g of sediment of the Savannah River basin, to 9 fCi/g for the Mississippi River basin, to 12 fCi/g for the Hudson River basin, to 14 fCi/g for the Columbia and Rio Grande River basins. 45 references, 2 figures, 17 tables

  15. Plutonium focus area

    International Nuclear Information System (INIS)

    1996-08-01

    To ensure research and development programs focus on the most pressing environmental restoration and waste management problems at the U.S. Department of Energy (DOE), the Assistant Secretary for the Office of Environmental Management (EM) established a working group in August 1993 to implement a new approach to research and technology development. As part of this new approach, EM developed a management structure and principles that led to the creation of specific Focus Areas. These organizations were designed to focus the scientific and technical talent throughout DOE and the national scientific community on the major environmental restoration and waste management problems facing DOE. The Focus Area approach provides the framework for intersite cooperation and leveraging of resources on common problems. After the original establishment of five major Focus Areas within the Office of Technology Development (EM-50, now called the Office of Science and Technology), the Nuclear Materials Stabilization Task Group (EM-66) followed the structure already in place in EM-50 and chartered the Plutonium Focus Area (PFA). The following information outlines the scope and mission of the EM, EM-60, and EM-66 organizations as related to the PFA organizational structure

  16. Plutonium solution analyzer

    International Nuclear Information System (INIS)

    Burns, D.A.

    1994-09-01

    A fully automated analyzer has been developed for plutonium solutions. It was assembled from several commercially available modules, is based upon segmented flow analysis, and exhibits precision about an order of magnitude better than commercial units (0.5%-O.05% RSD). The system was designed to accept unmeasured, untreated liquid samples in the concentration range 40-240 g/L and produce a report with sample identification, sample concentrations, and an abundance of statistics. Optional hydraulics can accommodate samples in the concentration range 0.4-4.0 g/L. Operating at a typical rate of 30 to 40 samples per hour, it consumes only 0.074 mL of each sample and standard, and generates waste at the rate of about 1.5 mL per minute. No radioactive material passes through its multichannel peristaltic pump (which remains outside the glovebox, uncontaminated) but rather is handled by a 6-port, 2-position chromatography-type loop valve. An accompanying computer is programmed in QuickBASIC 4.5 to provide both instrument control and data reduction. The program is truly user-friendly and communication between operator and instrument is via computer screen displays and keyboard. Two important issues which have been addressed are waste minimization and operator safety (the analyzer can run in the absence of an operator, once its autosampler has been loaded)

  17. Plutonium oxide shipment report

    International Nuclear Information System (INIS)

    1979-01-01

    While following procedures for unloading shipping containers containing plutonium oxide, SRP personnel experienced problems. While using a pipe cutter to cut through the wall of the inner container, the pipe section fell to the floor. Three empty food cans in the bottom of the inner canister also fell to the floor and a puff of smoke was observed. Personnel were evacuated and contamination was detected in the room. As a result of the investigations conducted by Westinghouse and SRP, thermal effects, food can coatings, and fuel volatiles were eliminated as the cause of the problem. Helium used to leak test the RL070 shipping container seals entered the inner canister through two weld defects resulting in a pressurization of the contents. When the end cap was removed, the inner canister vented rapidly, the food cans did not, thus creating a differential pressure across the food cans. This caused the food cans to swell. It was recommended that a dye penetrant test of all inner container welds be added. Additional unloading procedures were also recommended

  18. Plutonium solution analyzer

    Energy Technology Data Exchange (ETDEWEB)

    Burns, D.A.

    1994-09-01

    A fully automated analyzer has been developed for plutonium solutions. It was assembled from several commercially available modules, is based upon segmented flow analysis, and exhibits precision about an order of magnitude better than commercial units (0.5%-O.05% RSD). The system was designed to accept unmeasured, untreated liquid samples in the concentration range 40-240 g/L and produce a report with sample identification, sample concentrations, and an abundance of statistics. Optional hydraulics can accommodate samples in the concentration range 0.4-4.0 g/L. Operating at a typical rate of 30 to 40 samples per hour, it consumes only 0.074 mL of each sample and standard, and generates waste at the rate of about 1.5 mL per minute. No radioactive material passes through its multichannel peristaltic pump (which remains outside the glovebox, uncontaminated) but rather is handled by a 6-port, 2-position chromatography-type loop valve. An accompanying computer is programmed in QuickBASIC 4.5 to provide both instrument control and data reduction. The program is truly user-friendly and communication between operator and instrument is via computer screen displays and keyboard. Two important issues which have been addressed are waste minimization and operator safety (the analyzer can run in the absence of an operator, once its autosampler has been loaded).

  19. Plutonium dispositioning in CANDU

    International Nuclear Information System (INIS)

    Boczar, P.G.; Feinroth, H.; Luxat, J.C.

    1995-07-01

    Recently, the U.S. Department of Energy (DOE) sponsored Atomic Energy of Canada Limited (AECL) to evaluate salient technical, strategic, schedule, and cost-related parameters of using CANDU reactors for dispositioning of weapons-grade plutonium in the form of Mixed OXide (MOX) fuel. A study team, consisting of key staff from the CANDU reactor designers and researchers (AECL), operators (Ontario Hydro) and fuel suppliers, analyzed all significant factors involved in such application, with the objective of identifying an arrangement that would permit the burning of MOX in CANDU at the earliest date. One of Ontario Hydro's multi-unit stations, Bruce A nuclear generating station (4x769 MW(e)), was chosen as the reference for the study. The assessment showed that no significant modifications of reactor or process systems are necessary to operate with a full MOX core. Plant modifications would be limited to fuel handling and modifications necessary to accommodate enhanced security and safeguards requirements. No safety limitations were identified

  20. Long time contamination from plutonium

    International Nuclear Information System (INIS)

    Fueloep, M.; Patzeltova, N.; Ragan, P.; Matel, L.

    1995-01-01

    Plutonium isotopes in the organism of the patient (who had participated in the liquidation works after the Chernobyl accident; for three month he had stayed in the epicenter, where he acted as a chauffeur driving a radioactive material to the place of destination) from urine were determined. For determination of the concentration of Pu-239, Pu-240 in urine a modified radiochemical method was used. After mineralization the sample was separated as an anion-nitrate complex with contact by the anion form of the resin in the column. The resin was washed by 8 M HNO 3 , the 8 M HCl with 0.3 M HNO 3 for removing the other radionuclides. The solution 0.36 M HCl with 0.01 M HF was used for the elution of plutonium. Using the lanthanum fluoride technique the sample was filtrated through a membrane filter. The plutonium was detected in the dry sample. The Pu-239 tracer was used for the evaluation of the plutonium separation efficiency. The alpha spectrometric measurements were carried out with a large area silicon detector. The samples were measured and evaluated in the energy region 4.98-5.18 MeV. The detection limit of alpha spectrometry measurements has been 0.01 Bq dm -3 . The concentration of plutonium in the 24-hour urine was determined three times in the quarter year intervals. The results are: 54 mBq, 63.2 mBq, 53 mBq, with average 56,7 mBq. From the results of the analyses of plutonium depositions calculated according to ICRP 54 the intake of this radionuclide for the patient was 56.7 kBq. To estimate a committed effective dose (50 years) from the intake of plutonium was used a conversion factor 6.8.10 -5 Sv.Bq -1 (class W). So the expressed committed effective dose received from the plutonium intake is 3.8 Sv. This number is relatively high and all the effective dose will be higher, because the patient was exposed to the other radionuclides too. For example the determination of the rate radionuclides Am-241/Pu-239,Pu-240 was 32-36 % in the fallout after the Chernobyl

  1. Double shell tanks plutonium inventory assessment

    International Nuclear Information System (INIS)

    Tusler, L.A.

    1995-01-01

    This report provides an evaluation that establishes plutonium inventory estimates for all DSTs based on known tank history information, the DST plutonium inventory tracking system, tank characterization measurements, tank transfer records, and estimated average concentration values for the various types of waste. These estimates use data through December 31, 1994, and give plutonium estimates as of January 1, 1995. The plutonium inventory values for the DSTs are given in Section 31. The plutonium inventory estimate is 224 kg for the DSTs and 854 kg for the SSTs for a total of 1078 kg. This value compares favorably with the total plutonium inventory value of 981 kg obtained from the total plutonium production minus plutonium recovery analysis estimates

  2. Oxidation-state maxima in plutonium chemistry

    International Nuclear Information System (INIS)

    Silver, G.L.

    2013-01-01

    Maxima in the fractions of the trivalent and hexavalent oxidation states of plutonium are inherent in the algebra of its disproportionation reactions. The maxima do not support overall disproportionation equations as satisfactory representations of aqueous plutonium. (author)

  3. Recovery studies for plutonium machining oil coolant

    International Nuclear Information System (INIS)

    Navratil, J.D.; Baldwin, C.E.

    1977-01-01

    Lathe coolant oil, contaminated with plutonium and having a carbon tetrachloride diluent, is generated in plutonium machining areas at Rocky Flats. A research program was initiated to determine the nature of plutonium in this mixture of oil and carbon tetrachloride. Appropriate methods then could be developed to remove the plutonium and to recycle the oil and carbon tetrachloride. Studies showed that the mixtures of spent oil and carbon tetrachloride contained particulate plutonium and plutonium species that are soluble in water or in oil and carbon tetrachloride. The particulate plutonium was removed by filtration; the nonfilterable plutonium was removed by adsorption on various materials. Laboratory-scale tests indicated the lathe-coolant oil mixture could be separated by distilling the carbon tetrachloride to yield recyclable products

  4. Plutonium and americium separation from salts

    International Nuclear Information System (INIS)

    Hagan, P.G.; Miner, F.J.

    1976-01-01

    Salts or materials containing plutonium and americium are dissolved in hydrochloric acid, heated, and contacted with an alkali metal carbonate solution to precipitate plutonium and americium carbonates which are thereafter readily separable from the solution

  5. Plutonium-238 and plutonium-239 metabolism in dairy cows following ingestion of mixed oxides

    International Nuclear Information System (INIS)

    Patzer, R.G.; Mullen, A.A.; Sutton, W.W.; Potter, G.D.; Mosley, R.E.; Efurd, D.W.; Stalnaker, N.D.

    1985-01-01

    Dairy cows were given oral dosage of plutonium-238 and plutonium-239 dioxide particles in a study to determine the relative gastrointestinal absorption and tissue distribution of the nuclides. Two cows were given particles in which the two isotopes were homogeneously mixed within the particles. A third cow was given two batches of particles which contained either plutonium-238 or plutonium-239. Results indicate that, when the two isotopes of plutonium are homogeneous within the particles, there is no difference between plutonium-238 and plutonium-239 in the relative gastrointestinal absorption and tissue distribution

  6. Plutonium Disposition Now exclamation point

    International Nuclear Information System (INIS)

    Buckner, M.R.

    1995-01-01

    A means for use of existing processing facilities and reactors for plutonium disposition is described which requires a minimum capital investment and allows rapid implementation. The scenario includes interim storage and processing under IAEA control, and fabrication into MOX fuel in existing or planned facilities in Europe for use in operating reactors in the two home countries. Conceptual studies indicate that existing Westinghouse four-loop designs can safety dispose of 0.94 MT of plutonium per calendar year. Thus, it would be possible to consume the expected US excess stockpile of about 50 MT in two to three units of this type, and it is highly likely that a comparable amount of the FSU excess plutonium could be deposed of in a few VVER-1000's. The only major capital project for this mode of plutonium disposition would be the weapons-grade plutonium processing which could be done in a dedicated international facility or using existing facilities in the US and FSU under IAEA control. This option offers the potential for quick implementation at a very low cost to the governments of the two countries

  7. Selecting a plutonium vitrification process

    Energy Technology Data Exchange (ETDEWEB)

    Jouan, A. [Centre d`Etudes de la Vallee du Rhone, Bagnols sur Ceze (France)

    1996-05-01

    Vitrification of plutonium is one means of mitigating its potential danger. This option is technically feasible, even if it is not the solution advocated in France. Two situations are possible, depending on whether or not the glass matrix also contains fission products; concentrations of up to 15% should be achievable for plutonium alone, whereas the upper limit is 3% in the presence of fission products. The French continuous vitrification process appears to be particularly suitable for plutonium vitrification: its capacity is compatible with the required throughout, and the compact dimensions of the process equipment prevent a criticality hazard. Preprocessing of plutonium metal, to convert it to PuO{sub 2} or to a nitric acid solution, may prove advantageous or even necessary depending on whether a dry or wet process is adopted. The process may involve a single step (vitrification of Pu or PuO{sub 2} mixed with glass frit) or may include a prior calcination step - notably if the plutonium is to be incorporated into a fission product glass. It is important to weigh the advantages and drawbacks of all the possible options in terms of feasibility, safety and cost-effectiveness.

  8. Plutonium in depleted uranium penetrators

    International Nuclear Information System (INIS)

    McLaughlin, J.P.; Leon-Vintro, L.; Smith, K.; Mitchell, P.I.; Zunic, Z.S.

    2002-01-01

    Depleted Uranium (DU) penetrators used in the recent Balkan conflicts have been found to be contaminated with trace amounts of transuranic materials such as plutonium. This contamination is usually a consequence of DU fabrication being carried out in facilities also using uranium recycled from spent military and civilian nuclear reactor fuel. Specific activities of 239+240 Plutonium generally in the range 1 to 12 Bq/kg have been found to be present in DU penetrators recovered from the attack sites of the 1999 NATO bombardment of Kosovo. A DU penetrator recovered from a May 1999 attack site at Bratoselce in southern Serbia and analysed by University College Dublin was found to contain 43.7 +/- 1.9 Bq/kg of 239+240 Plutonium. This analysis is described. An account is also given of the general population radiation dose implications arising from both the DU itself and from the presence of plutonium in the penetrators. According to current dosimetric models, in all scenarios considered likely ,the dose from the plutonium is estimated to be much smaller than that due to the uranium isotopes present in the penetrators. (author)

  9. A World made of Plutonium?

    International Nuclear Information System (INIS)

    Broda, E.

    1976-01-01

    This lecture by Engelbert Broda was written for the 26th Pugwash Conference in Mühlhausen, Germany, 26 – 31 August 1976: Public doubts about nuclear energy are generally directed at the problems of routine emissions of radionuclides, of catastrophic accidents, and of terminal waste disposal. Curiously, the most important problem is not being given sufficient attention: The use of plutonium from civilian reactors fpr weapons production. According to current ideas about a nuclear future, 5000 tons (order of magnitude) of plutonium are to be made annually by year 2000, and about 10 000 tons will all the time be in circulation (transport, reprocessing, reproduction of fuel elements, etc.). It is a misconception that plutonium from power reactors is unsuitable as a nuclear explosive. 5000 tons are enough for several hundred thousand (!) of bombs, Nagasaki type. By the year 2000 maybe 40 – 50 countries will have home-made plutonium. Plutonium production and proliferation are the most serious problems in a nuclear world. (author)

  10. Plutonium determination by isotope dilution

    International Nuclear Information System (INIS)

    Lucas, M.

    1980-01-01

    The principle is to add to a known amount of the analysed solution a known amount of a spike solution consisting of plutonium 242. The isotopic composition of the resulting mixture is then determined by surface ionization mass spectrometry, and the plutonium concentration in the solution is deduced, from this measurement. For irradiated fuels neutronic studies or for fissile materials balance measurements, requiring the knowledge of the ratio U/Pu or of concentration both uranium and plutonium, it is better to use the double spike isotope dilution method, with a spike solution of known 233 U- 242 Pu ratio. Using this method, the ratio of uranium to plutonium concentration in the irradiated fuel solution can be determined without any accurate measurement of the mixed amounts of sample and spike solutions. For fissile material balance measurements, the uranium concentration is determined by using single isotope dilution, and the plutonium concentration is deduced from the ratio Pu/U and U concentration. The main advantages of isotope dilution are its selectivity, accuracy and very high sensitivity. The recent improvements made to surface ionization mass spectrometers have considerably increased the precision of the measurements; a relative precision of about 0.2% to 0.3% is obtained currently, but it could be reduced to 0.1%, in the future, with a careful control of the experimental procedures. The detection limite is around 0.1 ppb [fr

  11. Liquid waste processing from plutonium (III) oxalate precipitation

    International Nuclear Information System (INIS)

    Esteban, A.; Cassaniti, P.; Orosco, E.H.

    1990-01-01

    Plutonium (III) oxalate filtrates contain about 0.2M oxalic acid, 0.09M ascorbic acid, 0.05M hydrazine, 1M nitric acid and 20-100 mg/l of plutonium. The developed treatment of liquid wastes consist in two main steps: a) Distillation to reduce up to 10% of the initial volume and refluxing to destroy organic material. Then, the treated solution is suitable to adjust the plutonium at the tetravalent state by addition of hydrogen peroxide and the nitric molarity up to 8.6M. b) Recovery and purification of plutonium by anion exchange using two columns in series containing Dowex 1-X4 resin. With the proposed process, it is possible to transform 38 litres of filtrates with 40mg/l of Pu into 0.1 l of purified solution with 15-20g/l of Pu. This solution is suitable to be recycled in the Pu (III) oxalate precipitation process. This process has several potential advantages over similar liquid waste treatments. These include: 1) It does not increase the liquid volume. 2) It consumes only few reagents. 3) The operations involved are simple, requiring limited handling and they are feasible to automatization. 4) The Pu recovery factor is about 99%. (Author) [es

  12. Production of Plutonium Metal from Aqueous Solutions

    Energy Technology Data Exchange (ETDEWEB)

    Orth, D.A.

    2003-01-16

    The primary separation of plutonium from irradiated uranium by the Purex solvent extraction process at the Savannah River Plant produces a dilute plutonium solution containing residual fission products and uranium. A cation exchange process is used for concentration and further decontamination of the plutonium, as the first step in the final preparation of metal. This paper discusses the production of plutonium metal from the aqueous solutions.

  13. Plutonium Proliferation: The Achilles Heel of Disarmament

    International Nuclear Information System (INIS)

    Leventhal, Paul

    2001-01-01

    Plutonium is a byproduct of nuclear fission, and it is produced at the rate of about 70 metric tons a year in the world's nuclear power reactors. Concerns about civilian plutonium ran high in the 1970s and prompted enactment of the Nuclear Non-Proliferation Act of 1978 to give the United States a veto over separating plutonium from U.S.-supplied uranium fuel. Over the years, however, so-called reactor-grade plutonium has become the orphan issue of nuclear non-proliferation, largely as a consequence of pressures from plutonium-separating countries. The demise of the fast breeder reactor and the reluctance of utilities to introduce plutonium fuel in light-water reactors have resulted in large surpluses of civilian, weapons-usable plutonium, which now approach in size the 250 tons of military plutonium in the world. Yet reprocessing of spent fuel for recovery and use of plutonium proceeds apace outside the United States and threatens to overwhelm safeguards and security measures for keeping this material out of the hands of nations and terrorists for weapons. A number of historical and current developments are reviewed to demonstrate that plutonium commerce is undercutting efforts both to stop the spread of nuclear weapons and to work toward eliminating existing nuclear arsenals. These developments include the breakdown of U.S. anti-plutonium policy, the production of nuclear weapons by India with Atoms-for-Peace plutonium, the U.S.-Russian plan to introduce excess military plutonium as fuel in civilian power reactors, the failure to include civilian plutonium and bomb-grade uranium in the proposed Fissile Material Cutoff Treaty, and the perception of emerging proliferation threats as the rationale for development of a ballistic missile defense system. Finally, immobilization of separated plutonium in high-level waste is explored as a proliferation-resistant and disarmament-friendly solution for eliminating excess stocks of civilian and military plutonium.

  14. [Emotional valence of words in schizophrenia].

    Science.gov (United States)

    Jalenques, I; Enjolras, J; Izaute, M

    2013-06-01

    Emotion recognition is a domain in which deficits have been reported in schizophrenia. A number of emotion classification studies have indicated that emotion processing deficits in schizophrenia are more pronounced for negative affects. Given the difficulty of developing material suitable for the study of these emotional deficits, it would be interesting to examine whether patients suffering from schizophrenia are responsive to positively and negatively charged emotion-related words that could be used within the context of remediation strategies. The emotional perception of words was examined in a clinical experiment involving schizophrenia patients. This emotional perception was expressed by the patients in terms of the valence associated with the words. In the present study, we investigated whether schizophrenia patients would assign the same negative and positive valences to words as healthy individuals. Twenty volunteer, clinically stable, outpatients from the Psychiatric Service of the University Hospital of Clermont-Ferrand were recruited. Diagnoses were based on DSM-IV criteria. Global psychiatric symptoms were assessed using the Positive and Negative Symptoms Scale (PANSS). The patients had to evaluate the emotional valence of a set of 300 words on a 5-point scale ranging from "very unpleasant" to "very pleasant". . The collected results were compared with those obtained by Bonin et al. (2003) [13] from 97 University students. Correlational analyses of the two studies revealed that the emotional valences were highly correlated, i.e. the schizophrenia patients estimated very similar emotional valences. More precisely, it was possible to examine three separate sets of 100 words each (positive words, neutral words and negative words). The positive words that were evaluated were the more positive words from the norms collected by Bonin et al. (2003) [13], and the negative words were the more negative examples taken from these norms. The neutral words

  15. Convexity Adjustments

    DEFF Research Database (Denmark)

    M. Gaspar, Raquel; Murgoci, Agatha

    2010-01-01

    A convexity adjustment (or convexity correction) in fixed income markets arises when one uses prices of standard (plain vanilla) products plus an adjustment to price nonstandard products. We explain the basic and appealing idea behind the use of convexity adjustments and focus on the situations...

  16. Plutonium Oxide Process Capability Work Plan

    Energy Technology Data Exchange (ETDEWEB)

    Meier, David E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Tingey, Joel M. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2014-02-28

    Pacific Northwest National Laboratory (PNNL) has been tasked to develop a Pilot-scale Plutonium-oxide Processing Unit (P3U) providing a flexible capability to produce 200g (Pu basis) samples of plutonium oxide using different chemical processes for use in identifying and validating nuclear forensics signatures associated with plutonium production. Materials produced can also be used as exercise and reference materials.

  17. Civil plutonium amounts in the world

    International Nuclear Information System (INIS)

    Naudet, G.

    1994-01-01

    The experience of plutonium reprocessing in water reactors is positive and today the use of this nuclear fuel is at industrial level. Plutonium quantities in spent fuel go on increasing, plutonium stock coming from reprocessing can be controlled: according to conjuncture, it will evolve by stabilization or decreasing at the beginning of next century

  18. The use of calorimetry for plutonium assay

    International Nuclear Information System (INIS)

    Mason, J.A.

    1982-12-01

    Calorimetry is a technique for measuring the thermal power of heat-producing substances. The technique may be applied to the measurement of plutonium-bearing materials which evolve heat as a result of alpha and beta decay. A calorimetric measurement of the thermal power of a plutonium sample, combined with a knowledge or measurement of the plutonium isotopic mass ratios of the sample provides a convenient and accurate, non-destructive measure of the total plutonium mass of the sample. The present report provides a description, and an assessment of the calorimetry technique applied to the assay of plutonium-bearing materials. Types and characteristics of plutonium calorimeters are considered, as well as calibration and operating procedures. The instrumentation used with plutonium calorimeters is described and the use of computer control for calorimeter automation is discussed. A critical review and assessment of plutonium calorimetry literature since 1970 is presented. Both fuel element and plutonium-bearing material calorimeters are considered. The different types of plutonium calorimeters are evaluated and their relative merits are discussed. A combined calorimeter and gamma-ray measurement assay system is considered. The design principles of plutonium assay calorimeters are considered. An automatic, computer-based calorimeter control system is proposed in conjunction with a general plutonium assay calorimeter design. (author)

  19. Tabulated Neutron Emission Rates for Plutonium Oxide

    Energy Technology Data Exchange (ETDEWEB)

    Shores, Erik Frederick [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-07-24

    This work tabulates neutron emission rates for 80 plutonium oxide samples as reported in the literature. Plutonium-­238 and plutonium-­239 oxides are included and such emission rates are useful for scaling tallies from Monte Carlo simulations and estimating dose rates for health physics applications.

  20. Preventing pollution from plutonium processing

    International Nuclear Information System (INIS)

    Pillay, K.K.S.

    1993-01-01

    The plutonium processing facility at Los Alamos has adopted the strategic goal of becoming a facility that processes plutonium in a way that produces only environmentally benign waste streams. Pollution prevention through source reduction and environmentally sound recycling are being pursued. General approaches to waste reductions are administrative controls, modification of process technologies, and additional waste polishing. Recycling of waste materials, such as spent acids and salts, are technical possibilities and are being pursued to accomplish additional waste reduction. Liquid waste stream polishing to remove final traces of plutonium and hazardous chemical constituents is accomplished through (a) process modifications, (b) use of alternative chemicals and sorbents for residue removal, (c) acid recycling, and (d) judicious use of a variety of waste polishing technologies. Technologies that show promise in waste minimization and pollution prevention are identified. Working toward this goal of pollution prevention is a worthwhile endeavor, not only for Los Alamos, but for the Nuclear Complex of the future

  1. Technological alternatives for plutonium storage

    International Nuclear Information System (INIS)

    1978-12-01

    This paper discusses the problems of large long term storage since stores at fabrication plants may depend on the form of plutonium ultimately chosen for transport. The paper's conclusion includes: MOX can be regarded as more proliferation resistant than PUO 2 but no experience of long term storage is available, therefore further R and D is required; co-location of the store with reprocessing plants (and fuel fabrication plant) would appear to have advantages in non-proliferation, safeguards implementation, environmental protection and economic aspects; there are strong non-proliferation and security arguments for not moving plutonium away from the site where it was separated until there is an identifiable and scheduled end use. The design of the store, the form in which plutonium should be stored, particularly as MOX, and the costs and further R and D required are considered. The possible location of stores is also discussed and institutional questions briefly considered

  2. Plutonium and U-233 mines

    International Nuclear Information System (INIS)

    Milgram, M.S.

    1983-08-01

    A comparison is made among second generation reactor systems fuelled primarily with fissile plutonium and/or U-233 in uranium or thorium. This material is obtained from irradiated fuel from first generation CANDU reactors fuelled by natural or enriched uranium and thorium. Except for plutonium-thorium reactors, second generation reactors demand similar amounts of reprocessing throughput, but the most efficient plutonium burning systems require a large prior allocation of uranium. Second generation reactors fuelled by U-233 make more efficient use of resources and lead to more flexible fuelling strategies, but require development of first generation once-through thorium cycles and early demonstration of the commercial viability of thorium fuel reprocessing. No early implementation of reprocessing technology is required for these cycles

  3. Political influences in plutonium recycling

    International Nuclear Information System (INIS)

    Patak, H.N.

    1982-01-01

    The history of plutonium safeguards is one of political error and misunderstandings, as well as a lack of technical knowledge. Although there was widespread support for preventing the proliferation of nuclear explosives, with over 100 nations signing the Nonproliferation Treaty of 1969, India's 1974 nuclear test brought renewed political activity to prevent another such occurrence. Opposition has been directed only at how to pursue this goal, but the status of four major experiments aimed at minimizing weapons proliferation is one of failure, intensified by a weakening of the International Atomic Energy Agency (IAEA). If the link between plutonium power and weapons production can be broken through on-site reprocessing, the situation could improve. One course would be for the nuclear power industry to adopt its own system for safe guarding plutonium

  4. Plutonium and latent nuclear proliferation

    International Nuclear Information System (INIS)

    Quester, G.H.

    1992-01-01

    A country producing nuclear electric power acquires an ability to produce atomic bombs quite easily and without taking many steps beyond that which would be perfectly normal for civilian purposes. The role of plutonium in the three fold list of the gains that must be sought in arms control formulated by Schelling and Halpevin are discussed. On the first, that we should seek to reduce the likelihood of war, it can be argued that plutonium reduces the likelihood in some cases. The second, that we should seek to reduce the destruction in war, is made worse by plutonium. On the third criterion, that we should seek to reduce the burdens in peacetime of everyone's being prepared for war, the situation is confusing and depends on the prospects for nuclear electrical power. It is concluded that latent capability to produce nuclear weapons may be sufficient without the need for actual detonations and deployment of bombs. (UK)

  5. Plutonium accident resistant container project

    International Nuclear Information System (INIS)

    Andersen, J.A.

    1978-09-01

    The PARC (plutonium accident resistant container) project resulted in the design, development, and certification testing of a crashworthy air-transportable plutonium package (shipping container) for certification by the USNRC (Nuclear Regulatory Commission). This PAT-1 (plutonium air transportable) package survives a very severe sequential test program of impact, crush, puncture, slash, burn, and water immersion. There is also an individual hydrostatic pressure test. The package has a payload mass capacity of 2 kg of PuO 2 and a thermal capacity of 25 watts. The design rationale for very high energy absorption (impact, crush, puncture, and slash protection) with residual high-level fire protection, resulted in a reasonably small air-transportable package, advancing the packaging state-of-art. Optimization design iterations were utilized in the areas of impact energy absorption and stress and thermal analysis. Package test results are presented in relation to radioactive materials containment acceptance criteria, shielding and criticality standards

  6. Plutonium accident resistant container project

    International Nuclear Information System (INIS)

    Andersen, J.A.

    1978-05-01

    The PARC (plutonium accident resistant container) project resulted in the design, development, and certification testing of a crashworthy air-transportable plutonium package (shipping container) for certification by the USNRC. This PAT-1 (plutonium air transportable) package survives a very severe sequential test program of impact, crush, puncture, slash, burn, and water immersion. There is also an individual hydrostatic pressure test. The package has a payload mass capacity of 2 kg of PuO2 and a thermal capacity of 25 watts. The design rationale for very high energy absorption (impact, crush, puncture, and slash protection) with residual high-level fire protection, resulted in a reasonalby small air-transportable package, advancing the packaging state-of-art. Optimization design iterations were utilized in the areas of impact energy absorption and stress and thermal analysis. Package test results are presented in relation to radioactive materials containment acceptance criteria, shielding and criticality standards

  7. Shielding calculational system for plutonium

    International Nuclear Information System (INIS)

    Zimmerman, M.G.; Thomsen, D.H.

    1975-08-01

    A computer calculational system has been developed and assembled specifically for calculating dose rates in AEC plutonium fabrication facilities. The system consists of two computer codes and all nuclear data necessary for calculation of neutron and gamma dose rates from plutonium. The codes include the multigroup version of the Battelle Monte Carlo code for solution of general neutron and gamma shielding problems and the PUSHLD code for solution of shielding problems where low energy gamma and x-rays are important. The nuclear data consists of built in neutron and gamma yields and spectra for various plutonium compounds, an automatic calculation of age effects and all cross-sections commonly used. Experimental correlations have been performed to verify portions of the calculational system. (23 tables, 7 figs, 16 refs) (U.S.)

  8. Preventing pollution from plutonium processing

    International Nuclear Information System (INIS)

    Pillay, K.K.S.

    1995-01-01

    The plutonium processing facility at Los Alamos has adopted the strategic goal of becoming a facility that processes plutonium in a way that produces only environmentally benign waste streams. Pollution prevention through source reduction and environmentally sound recycling are being pursued. General approaches to waste reductions are administrative controls, modification of process technologies, and additional waste polishing. Recycling of waste materials, such as spent acids and salts, are technical possibilities and are being pursued to accomplish additional waste reduction. Liquid waste stream polishing to remove final traces of plutonium and hazardous chemical constituents is accomplished through process modifications, use of alternative chemicals and sorbents for residue removal, acid recycling, and judicious use of a variety of waste polishing technologies. Technologies that show promise in waste minimization and pollution prevention are identified. Working toward this goal of pollution prevention is a worthwhile endeavor , not only for Los Alamos, but for the Nuclear Complex of the future. (author) 12 refs.; 2 figs

  9. Safeguarding the Plutonium Fuel Cycle

    International Nuclear Information System (INIS)

    Johnson, S.J.; Lockwood, D.

    2013-01-01

    In developing a Safeguards Approach for a plutonium process facility, two general diversion and misuse scenarios must be addressed: 1) Unreported batches of undeclared nuclear material being processed through the plant and bypassing the accountancy measurement points, and 2) The operator removing plutonium at a rate that cannot be detected with confidence due to measurement uncertainties. This paper will look at the implementation of international safeguards at plutonium fuel cycle facilities in light of past lessons learned and current safeguards approaches. It will then discuss technical areas which are currently being addressed as future tools to improve on the efficiency of safeguards implementation, while maintaining its effectiveness. The discussion of new improvements will include: safeguards by design (SBD), process monitoring (PM), measurement and monitoring equipment, and data management. The paper is illustrated with the implementation of international safeguards at the Rokkasho Reprocessing Plant in Japan and its accountancy structure is detailed. The paper is followed by the slides of the presentation

  10. Nukem's plutonium hitches a ride

    International Nuclear Information System (INIS)

    Anon.

    1988-01-01

    The European repercussions of a scandal involving the illegal movement of plutonium and cobalt 60 in canisters in which it was claimed there was only low-level radioactive waste, from West Germany to the reprocessing centre at Mol, Belgium are considered. Large bribes were paid to employees of the nuclear industry and government inspectors to allow this illicit transport to carry on over a number of years. It is not yet clear where the plutonium came from or where it was going. The suggestion that it may have been sold to Libya or Pakistan for nuclear weapons is very damaging to the nuclear safety argument. Even if the plutonium was being disposed of because it could not be accounted for, the safeguard procedures do not give confidence to the European public more aware of nuclear safety than ever. (UK)

  11. Plutonium-238 Decision Analysis

    International Nuclear Information System (INIS)

    Brown, Mike; Lechel, David J.; Leigh, C.D.

    1999-01-01

    Five transuranic (TRU) waste sites in the Department of Energy (DOE) complex, collectively, have more than 2,100 cubic meters of Plutonium-238 (Pu-238) TRU waste that exceed the wattage restrictions of the Transuranic Package Transporter-II (TRUPACT-11). The Waste Isolation Pilot Plant (WIPP) is being developed by the DOE as a repository for TRU waste. With the Waste Isolation Pilot Plant (WIPP) opening in 1999, these sites are faced with a need to develop waste management practices that will enable the transportation of Pu-238 TRU waste to WIPP for disposal. This paper describes a decision analysis that provided a logical framework for addressing the Pu-238 TRU waste issue. The insights that can be gained by performing a formalized decision analysis are multifold. First and foremost, the very process. of formulating a decision tree forces the decision maker into structured, logical thinking where alternatives can be evaluated one against the other using a uniform set of criteria. In the process of developing the decision tree for transportation of Pu-238 TRU waste, several alternatives were eliminated and the logical order for decision making was discovered. Moreover, the key areas of uncertainty for proposed alternatives were identified and quantified. The decision analysis showed that the DOE can employ a combination approach where they will (1) use headspace gas analyses to show that a fraction of the Pu-238 TRU waste drums are no longer generating hydrogen gas and can be shipped to WIPP ''as-is'', (2) use drums and bags with advanced filter systems to repackage Pu-238 TRU waste drums that are still generating hydrogen, and (3) add hydrogen getter materials to the inner containment vessel of the TRUPACT-11to relieve the build-up of hydrogen gas during transportation of the Pu-238 TRU waste drums

  12. Plutonium in a grassland ecosystem

    International Nuclear Information System (INIS)

    Little, C.A.

    1976-01-01

    This study was concerned with plutonium contamination of grassland at the U.S. Energy Research and Development Administration Rocky Flats plant northwest of Denver, Colorado. Of interest were: the definition of major plutonium-containing ecosystem compartments; the relative amounts in those compartments; how those values related to studies done in other geogrphical areas; whether or not the predominant isotopes, 238 Pu and 239 Pu, behaved differently; and what mechanisms might have allowed for the observed patterns of contamination. Samples of soil, litter, vegetation, arthropods, and small mammals were collected for plutonium analysis and mass determination from each of two macroplots. Small aliquots (5 g or less) were analyzed by a rapid liquid scintillation technique and by alpha spectrometry. Of the compartments sampled, greater than 99% of the total plutonium was contained in the soil. The concentrations of plutonium in soil were significantly inversely correlated with distance from the contamination source, depth of the sample, and particle size of the sieved soil samples. The soil data suggested that the distribution of contamination largely resulted from physical transport processes. A mechanism of agglomerated submicron plutonium oxide particles and larger (1-500 μm) host soil particles was proposed. Concentrations of Pu in litter and vegetation were inversely correlated to distance from the source and directly correlated to soil concentrations at the same location. Comparatively high concentration ratios of vegetation to soil suggested wind resuspension of contamination as an important transport mechanism. Arthropod and small mammal samples were highly skewed, kurtotic, and quite variable, having coefficients of variation (standard deviation/mean) as high as 600%. Bone Pu concentrations were lower than other tissues. Hide, GI, and lung were generally not higher in Pu than kidney, liver and muscle

  13. Plutonium stabilization and packaging system

    International Nuclear Information System (INIS)

    1996-01-01

    This document describes the functional design of the Plutonium Stabilization and Packaging System (Pu SPS). The objective of this system is to stabilize and package plutonium metals and oxides of greater than 50% wt, as well as other selected isotopes, in accordance with the requirements of the DOE standard for safe storage of these materials for 50 years. This system will support completion of stabilization and packaging campaigns of the inventory at a number of affected sites before the year 2002. The package will be standard for all sites and will provide a minimum of two uncontaminated, organics free confinement barriers for the packaged material

  14. Long time contamination from plutonium

    Energy Technology Data Exchange (ETDEWEB)

    Fueloep, M; Patzeltova, N; Ragan, P [Inst. of Preventive and Clinical Medicine, Bratislava (Slovakia); Matel, L [Comenius Univ., Bratislava (Slovakia). Department of Nuclear Chemistry

    1996-12-31

    Plutonium isotopes in the organism of the patient (who had participated in the liquidation works after the Chernobyl accident; for three month he had stayed in the epicenter, where he acted as a chauffeur driving a radioactive material to the place of destination) from urine were determined. For determination of the concentration of Pu-239, Pu-240 in urine a modified radiochemical method was used. After mineralization the sample was separated as an anion-nitrate complex with contact by the anion form of the resin in the column. The resin was washed by 8 M HNO{sub 3}, the 8 M HCl with 0.3 M HNO{sub 3} for removing the other radionuclides. The solution 0.36 M HCl with 0.01 M HF was used for the elution of plutonium. Using the lanthanum fluoride technique the sample was filtrated through a membrane filter. The plutonium was detected in the dry sample. The Pu-239 tracer was used for the evaluation of the plutonium separation efficiency. The alpha spectrometric measurements were carried out with a large area silicon detector. The samples were measured and evaluated in the energy region 4.98-5.18 MeV. The detection limit of alpha spectrometry measurements has been 0.01 Bq dm{sup -3}. The concentration of plutonium in the 24-hour urine was determined three times in the quarter year intervals. The results are: 54 mBq, 63.2 mBq, 53 mBq, with average 56,7 mBq. From the results of the analyses of plutonium depositions calculated according to ICRP 54 the intake of this radionuclide for the patient was 56.7 kBq. To estimate a committed effective dose (50 years) from the intake of plutonium was used a conversion factor 6.8.10{sup -5} Sv.Bq{sup -1} (class W). So the expressed committed effective dose received from the plutonium intake is 3.8 Sv. This number is relatively high and all the effective dose will be higher, because the patient was exposed to the other radionuclides too. (Abstract Truncated)

  15. Decoding emotional valence from electroencephalographic rhythmic activity.

    Science.gov (United States)

    Celikkanat, Hande; Moriya, Hiroki; Ogawa, Takeshi; Kauppi, Jukka-Pekka; Kawanabe, Motoaki; Hyvarinen, Aapo

    2017-07-01

    We attempt to decode emotional valence from electroencephalographic rhythmic activity in a naturalistic setting. We employ a data-driven method developed in a previous study, Spectral Linear Discriminant Analysis, to discover the relationships between the classification task and independent neuronal sources, optimally utilizing multiple frequency bands. A detailed investigation of the classifier provides insight into the neuronal sources related with emotional valence, and the individual differences of the subjects in processing emotions. Our findings show: (1) sources whose locations are similar across subjects are consistently involved in emotional responses, with the involvement of parietal sources being especially significant, and (2) even though the locations of the involved neuronal sources are consistent, subjects can display highly varying degrees of valence-related EEG activity in the sources.

  16. Plutonium and americium behavior in coral atoll environments

    International Nuclear Information System (INIS)

    Noshkin, V.E.; Wong, K.M.; Jokela, T.A.; Brunk, J.L.; Eagle, R.J.

    1984-01-01

    Inventories of 239+240 Pu and 241 Am greatly in excess of global fallout levels persist in the benthic environments of Bikini and Enewetak Atolls. Quantities of 239+240 Pu and lesser amounts of 241 Am are continuously mobilizing from these sedimentary reservoirs. The amount of 239+240 Pu mobilized to solution at any time represents 0.08 to 0.09% of the sediment inventories to a depth of 16 cm. The mobilized 239+240 Pu has solute-like characteristics and different valence states coexist in solution - the largest fraction of the soluble plutonium is in an oxidized form (+V,VI). The adsorption of plutonium to sediments is not completely reversible because of changes that occur in the relative amounts of the mixed oxidation states in solution with time. Further, any characteristics of 239+240 Pu described at one location may not necessarily be relevant in describing its behavior elsewhere following mobilization and migration. The relative amounts of 241 Am to 239+240 Pu in the sedimentary deposits at Enewetak and Bikini may be altered in future years because of mobilization and radiological decay. Mobilization of 239+240 Pu is not a process unique to these atolls, and quantities in solution derived from sedimentary deposits can be found at other global sites. These studies in the equatorial Pacific have significance in assessing the long-term behavior of the transuranics in any marine environment. 22 references, 1 figure, 13 tables

  17. Determination of plutonium-238 in plutonium by alpha spectrometry

    International Nuclear Information System (INIS)

    Aggarwal, S.K.; Jain, H.C.; Mathews, C.K.; Ramaniah, M.V.

    1975-01-01

    A method is presented for the determination of 238 Pu in plutonium samples by alpha spectrometry. Various factors attributing towards the energy degradation, a problem usually encountered in alpha spectrometry, are discussed. A computer programme is given for the evaluation of peak areas when the alpha spectrum is degraded. The results are compared with those obtained by mass spectrometry. (author)

  18. Emotions and false memories: valence or arousal?

    Science.gov (United States)

    Corson, Yves; Verrier, Nadège

    2007-03-01

    The effects of mood on false memories have not been studied systematically until recently. Some results seem to indicate that negative mood may reduce false recall and thus suggest an influence of emotional valence on false memory. The present research tested the effects of both valence and arousal on recall and recognition and indicates that the effect is actually due to arousal. In fact, whether participants' mood is positive, negative, or neutral, false memories are significantly more frequent under conditions of high arousal than under conditions of low arousal.

  19. Valence electronic properties of porphyrin derivatives.

    Science.gov (United States)

    Stenuit, G; Castellarin-Cudia, C; Plekan, O; Feyer, V; Prince, K C; Goldoni, A; Umari, P

    2010-09-28

    We present a combined experimental and theoretical investigation of the valence electronic structure of porphyrin-derived molecules. The valence photoemission spectra of the free-base tetraphenylporphyrin and of the octaethylporphyrin molecule were measured using synchrotron radiation and compared with theoretical spectra calculated using the GW method and the density-functional method within the generalized gradient approximation. Only the GW results could reproduce the experimental data. We found that the contribution to the orbital energies due to electronic correlations has the same linear behavior in both molecules, with larger deviations in the vicinity of the HOMO level. This shows the importance of adequate treatment of electronic correlations in these organic systems.

  20. Plutonium Speciation, Solubilization and Migration in Soils

    International Nuclear Information System (INIS)

    Neu, M.; Runde, W.

    1999-01-01

    This report summarizes research completed in the first half of a three-year project. As outlined in the authors' proposal they are focusing on (1) characterizing the plutonium at an actinide contaminated site, RFETS, including determining the origin, dispersion, and speciation of the plutonium, (2) studying environmentally important plutonium complexes, primarily hydroxides and carbonates, and (3) examining the interactions of plutonium species with manganese minerals. In the first year the authors focused on site based studies. This year they continue to characterize samples from the RFETS, study the formation and structural and spectroscopic features of environmentally relevant Pu species, and begin modeling the environmental behavior of plutonium

  1. Plutonium recovery from carbonate wash solutions

    International Nuclear Information System (INIS)

    Gray, J.H.; Reif, D.J.; Chostner, D.F.; Holcomb, H.P.

    1991-01-01

    540Periodically higher than expected levels of plutonium are found in carbonate solutions used to wash second plutonium cycle solvent. The recent accumulation of plutonium in carbonate wash solutions has led to studies to determine the cause of that plutonium accumulation, to evaluate the quality of all canyon solvents, and to develop additional criteria needed to establish when solvent quality is acceptable. Solvent from three canyon solvent extraction cycles was used to evaluate technology required to measure tributyl phosphate (TBP) degradation products and was used to evaluate solvent quality criteria during the development of plutonium recovery processes. 1 fig

  2. Plutonium inventories for stabilization and stabilized materials

    Energy Technology Data Exchange (ETDEWEB)

    Williams, A.K.

    1996-05-01

    The objective of the breakout session was to identify characteristics of materials containing plutonium, the need to stabilize these materials for storage, and plans to accomplish the stabilization activities. All current stabilization activities are driven by the Defense Nuclear Facilities Safety Board Recommendation 94-1 (May 26, 1994) and by the recently completed Plutonium ES&H Vulnerability Assessment (DOE-EH-0415). The Implementation Plan for accomplishing stabilization of plutonium-bearing residues in response to the Recommendation and the Assessment was published by DOE on February 28, 1995. This Implementation Plan (IP) commits to stabilizing problem materials within 3 years, and stabilizing all other materials within 8 years. The IP identifies approximately 20 metric tons of plutonium requiring stabilization and/or repackaging. A further breakdown shows this material to consist of 8.5 metric tons of plutonium metal and alloys, 5.5 metric tons of plutonium as oxide, and 6 metric tons of plutonium as residues. Stabilization of the metal and oxide categories containing greater than 50 weight percent plutonium is covered by DOE Standard {open_quotes}Criteria for Safe Storage of Plutonium Metals and Oxides{close_quotes} December, 1994 (DOE-STD-3013-94). This standard establishes criteria for safe storage of stabilized plutonium metals and oxides for up to 50 years. Each of the DOE sites and contractors with large plutonium inventories has either started or is preparing to start stabilization activities to meet these criteria.

  3. Burning weapons-grade plutonium in reactors

    International Nuclear Information System (INIS)

    Newman, D.F.

    1993-06-01

    As a result of massive reductions in deployed nuclear warheads, and their subsequent dismantlement, large quantities of surplus weapons- grade plutonium will be stored until its ultimate disposition is achieved in both the US and Russia. Ultimate disposition has the following minimum requirements: (1) preclude return of plutonium to the US and Russian stockpiles, (2) prevent environmental damage by precluding release of plutonium contamination, and (3) prevent proliferation by precluding plutonium diversion to sub-national groups or nonweapons states. The most efficient and effective way to dispose of surplus weapons-grade plutonium is to fabricate it into fuel and use it for generation of electrical energy in commercial nuclear power plants. Weapons-grade plutonium can be used as fuel in existing commercial nuclear power plants, such as those in the US and Russia. This recovers energy and economic value from weapons-grade plutonium, which otherwise represents a large cost liability to maintain in safeguarded and secure storage. The plutonium remaining in spent MOX fuel is reactor-grade, essentially the same as that being discharged in spent UO 2 fuels. MOX fuels are well developed and are currently used in a number of LWRs in Europe. Plutonium-bearing fuels without uranium (non-fertile fuels) would require some development. However, such non-fertile fuels are attractive from a nonproliferation perspective because they avoid the insitu production of additional plutonium and enhance the annihilation of the plutonium inventory on a once-through fuel cycle

  4. The first weighing of plutonium

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1967-09-10

    The following text, transcribed from the remarks of those scientists who gathered at the University of Chicago on September 10, 1967, to celebrate the 25th anniversary of the first weighing of plutonium, tells an important part of the story of this fascinating new element that is destined to play an increasingly significant role in the future of man.

  5. Spectrographic analysis of plutonium (1960)

    International Nuclear Information System (INIS)

    Artaud, J.; Chaput, M.; Robichet, J.

    1960-01-01

    Various possibilities for the spectrographic determination of impurities in plutonium are considered. The application of the 'copper spark' method, of sparking on graphite and of fractional distillation in the arc are described and discussed in some detail (apparatus, accessories, results obtained). (author) [fr

  6. Plutonium waste incineration using pyrohydrolysis

    International Nuclear Information System (INIS)

    Meyer, M.L.

    1991-01-01

    Waste generated by Savannah River Site (SRS) plutonium operations includes a contaminated organic waste stream. A conventional method for disposing of the organic waste stream and recovering the nuclear material is by incineration. When the organic material is burned, the plutonium remains in the incinerator ash. Plutonium recovery from incinerator ash is highly dependent on the maximum temperature to which the oxide is exposed. Recovery via acid leaching is reduced for a high fired ash (>800 degree C), while plutonium oxides fired at lower decomposition temperatures (400--800 degrees C) are more soluble at any given acid concentration. To determine the feasibility of using a lower temperature process, tests were conducted using an electrically heated, controlled-air incinerator. Nine nonradioactive, solid, waste materials were batch-fed and processed in a top-heated cylindrical furnace. Waste material processing was completed using a 19-liter batch over a nominal 8-hour cycle. A processing cycle consisted of 1 hour for heating, 4 hours for reacting, and 3 hours for chamber cooling. The water gas shift reaction was used to hydrolyze waste materials in an atmosphere of 336% steam and 4.4% oxygen. Throughput ranged from 0.14 to 0.27 kg/hr depending on the variability in the waste material composition and density

  7. The first weighing of plutonium

    International Nuclear Information System (INIS)

    1967-01-01

    The following text, transcribed from the remarks of those scientists who gathered at the University of Chicago on September 10, 1967, to celebrate the 25th anniversary of the first weighing of plutonium, tells an important part of the story of this fascinating new element that is destined to play an increasingly significant role in the future of man

  8. Safe disposal of surplus plutonium

    Science.gov (United States)

    Gong, W. L.; Naz, S.; Lutze, W.; Busch, R.; Prinja, A.; Stoll, W.

    2001-06-01

    About 150 tons of weapons grade and weapons usable plutonium (metal, oxide, and in residues) have been declared surplus in the USA and Russia. Both countries plan to convert the metal and oxide into mixed oxide fuel for nuclear power reactors. Russia has not yet decided what to do with the residues. The US will convert residues into a ceramic, which will then be over-poured with highly radioactive borosilicate glass. The radioactive glass is meant to provide a deterrent to recovery of plutonium, as required by a US standard. Here we show a waste form for plutonium residues, zirconia/boron carbide (ZrO 2/B 4C), with an unprecedented combination of properties: a single, radiation-resistant, and chemically durable phase contains the residues; billion-year-old natural analogs are available; and criticality safety is given under all conceivable disposal conditions. ZrO 2/B 4C can be disposed of directly, without further processing, making it attractive to all countries facing the task of plutonium disposal. The US standard for protection against recovery can be met by disposal of the waste form together with used reactor fuel.

  9. Design of plutonium processing facilities

    International Nuclear Information System (INIS)

    Derbyshire, W.; Sills, R.J.

    1982-01-01

    Five considerations for the design of plutonium processing facilities are identified. These are: Toxicity, Radiation, Criticality, Containment and Remote Operation. They are examined with reference to reprocessing spent nuclear fuel and application is detailed both for liquid and dry processes. (author)

  10. On plutonium, journalism and ethics

    International Nuclear Information System (INIS)

    Rundo, J.

    1994-01-01

    This editorial comments on the furore resulting from three lay articles published by E. Welsome in the Albuquerque Tribune for 15 November 1993, concerning the injection of plutonium into humans in the 1940s, and discusses the ethics of administration of radioactive materials with and without informed consent. (Author)

  11. Management of Russian military plutonium

    International Nuclear Information System (INIS)

    Zaleski, C.P.

    1996-01-01

    The objective of this paper is to propose and discuss a solution which enables storing as quickly as possible all weapons-grade plutonium from Russian military program in a way which would prevent diversion. Two main conditions apply to this solution. First, it should be achieved in a manner acceptable to Russian government, notably by preserving plutonium for possible future energy production, and second, the economics of the total system should be good enough to ensure no charge or limited charge for the storage of plutonium. A proposal is made to store plutonium in a specially designed fast reactor or specially designed reactor core. This solution could be favorable in comparison to other solutions applying the above mentioned goal and conditions. Additionally the proposed solution would have the following side advantages: utilizing available personnel and installations of the Russian nuclear complex; providing possible basis for decommissioning of older and less safe Russian reactors; giving experience of construction and operation of a series of sodium-cooled fast reactors. The major problem however is the need for large capital investment with the risk of getting no adequate return on investment due to difficult political and economic situation in Russia

  12. Double-valence-fluctuating molecules and superconductivity

    International Nuclear Information System (INIS)

    Hirsch, J.E.; Scalapino, D.J.

    1985-01-01

    We discuss the possibility of ''double-valence-fluctuating'' molecules, having two ground-state configurations differing by two electrons. We propose a possible realization of such a molecule, and experimental ways to look for it. We argue that a weakly coupled array of such molecules should give rise to a strong-coupling Shafroth-Blatt-Butler superconductor, with a high transition temperature

  13. NEVER forget: negative emotional valence enhances recapitulation.

    Science.gov (United States)

    Bowen, Holly J; Kark, Sarah M; Kensinger, Elizabeth A

    2017-07-10

    A hallmark feature of episodic memory is that of "mental time travel," whereby an individual feels they have returned to a prior moment in time. Cognitive and behavioral neuroscience methods have revealed a neurobiological counterpart: Successful retrieval often is associated with reactivation of a prior brain state. We review the emerging literature on memory reactivation and recapitulation, and we describe evidence for the effects of emotion on these processes. Based on this review, we propose a new model: Negative Emotional Valence Enhances Recapitulation (NEVER). This model diverges from existing models of emotional memory in three key ways. First, it underscores the effects of emotion during retrieval. Second, it stresses the importance of sensory processing to emotional memory. Third, it emphasizes how emotional valence - whether an event is negative or positive - affects the way that information is remembered. The model specifically proposes that, as compared to positive events, negative events both trigger increased encoding of sensory detail and elicit a closer resemblance between the sensory encoding signature and the sensory retrieval signature. The model also proposes that negative valence enhances the reactivation and storage of sensory details over offline periods, leading to a greater divergence between the sensory recapitulation of negative and positive memories over time. Importantly, the model proposes that these valence-based differences occur even when events are equated for arousal, thus rendering an exclusively arousal-based theory of emotional memory insufficient. We conclude by discussing implications of the model and suggesting directions for future research to test the tenets of the model.

  14. Uranium, plutonium and co

    International Nuclear Information System (INIS)

    Sauerbrey, Roland; Joehnk, Peter

    2016-01-01

    To date there is no repository facility for highly radioactive and heat-generating waste in Germany. This politically ''hot'' topic is undeniably a very big, urgent problem in our society. The Helmholtz Association of German Research Centers is dedicated to developing scientific solutions for such issues. It looks back on 20 years of history: In 1995 the loosely organized collective bearing the name ''Working Association of Large-Scale Research Institutes'' (Arbeitsgemeinschaft der Grossforschungseinrichtungen) became an association of now 18 research centers. These centers collectively work in a total of six research areas. While the HZDR has only belonged to the largest research association in Germany since 2011, repository research was already on the agenda way back when the Rossendorf research center established itself in 1992 after the fall of the Berlin Wall. A good enough reason to examine the results from about 20 years of repository research in Dresden in more detail. In this issue of ''discovered'' we will take an inside look at radiochemical, radiogeological, and microbiological labs, look over the shoulders of researchers using the ''Rossendorf Beamline'' at the European Synchrotron Radiation Facility in Grenoble, and descend hundreds of meters into Finnish, Swedish, and Swiss research labs. How do ''uranium, plutonium, and co.'' react with mineral surfaces in environments that are low in oxygen or watery? How do they interact with microorganisms deep underground? And how can host rock or other materials be used as technical barriers to prevent the spread of radioactive substances? In order to answer these and further questions, the researchers of the HZDR use a wide range of spectroscopic methods. They expose test samples to lasers, infrared light, and X-rays or use the fluorescent properties of certain compounds to learn about the behavior of actinides

  15. Uranium, plutonium and co

    Energy Technology Data Exchange (ETDEWEB)

    Sauerbrey, Roland; Joehnk, Peter (eds.)

    2016-04-15

    To date there is no repository facility for highly radioactive and heat-generating waste in Germany. This politically ''hot'' topic is undeniably a very big, urgent problem in our society. The Helmholtz Association of German Research Centers is dedicated to developing scientific solutions for such issues. It looks back on 20 years of history: In 1995 the loosely organized collective bearing the name ''Working Association of Large-Scale Research Institutes'' (Arbeitsgemeinschaft der Grossforschungseinrichtungen) became an association of now 18 research centers. These centers collectively work in a total of six research areas. While the HZDR has only belonged to the largest research association in Germany since 2011, repository research was already on the agenda way back when the Rossendorf research center established itself in 1992 after the fall of the Berlin Wall. A good enough reason to examine the results from about 20 years of repository research in Dresden in more detail. In this issue of ''discovered'' we will take an inside look at radiochemical, radiogeological, and microbiological labs, look over the shoulders of researchers using the ''Rossendorf Beamline'' at the European Synchrotron Radiation Facility in Grenoble, and descend hundreds of meters into Finnish, Swedish, and Swiss research labs. How do ''uranium, plutonium, and co.'' react with mineral surfaces in environments that are low in oxygen or watery? How do they interact with microorganisms deep underground? And how can host rock or other materials be used as technical barriers to prevent the spread of radioactive substances? In order to answer these and further questions, the researchers of the HZDR use a wide range of spectroscopic methods. They expose test samples to lasers, infrared light, and X-rays or use the fluorescent properties of certain compounds to learn about the behavior of actinides

  16. Reducing the negative valence of stressful memories through emotionally valenced, modality-specific tasks

    NARCIS (Netherlands)

    Tadmor, Avia; McNally, Richard J; Engelhard, Iris M

    2016-01-01

    BACKGROUND AND OBJECTIVES: People who perform a cognitively demanding secondary task while recalling a distressing memory often experience the memory as less emotional, vivid, or accurate during subsequent recollections. In this experiment, we tested whether the emotional valence (positive versus

  17. Physics of Plutonium Recycling in Thermal Reactors

    International Nuclear Information System (INIS)

    Kinchin, G.H.

    1967-01-01

    A substantial programme of experimental reactor physics work with plutonium fuels has been carried out in the UK; the purpose of this paper is to review the experimental and theoretical work, with emphasis on plutonium recycling in thermal reactors. Although the main incentive for some of the work may have been to study plutonium build-up in uranium-fuelled reactors, it is nevertheless relevant to plutonium recycling and no distinction is drawn between build-up and enrichment studies. A variety of techniques have been for determining reactivity, neutron spectrum and reaction rates in simple assemblies of plutonium-aluminium fuel with water, graphite and beryllia moderators. These experiments give confidence in the basic data and methods of calculation for near-homogeneous mixtures of plutonium and moderator. In the practical case of plutonium recycling it is necessary to confirm that satisfactory predictions can be made for heterogeneous lattices enriched with plutonium. In this field, experiments have been carried out with plutonium-uranium metal and oxide-cluster fuels in graphite-moderated lattices and in SGHW lattices, and the effects of 240 Pu have been studied by perturbation measurements with single fuel elements. The exponential and critical experiments have used tonne quantities of fuel with plutonium contents ranging from 0.25 to 1.2% and the perturbation experiments have extended both the range of plutonium contents and the range of isotopic compositions of plutonium. In addition to reactivity and reactivity coefficients, such as the temperature coefficients, attention has been concentrated on relative reaction rate distributions which provide evidence for variations of neutron spectrum. .Theoretical comparisons, together with similar comparisons for non-uniform lattices, establish the validity of methods of calculation which have been used to study the feasibility of plutonium recycling in thermal reactors. (author)

  18. Physics of Plutonium Recycling in Thermal Reactors

    Energy Technology Data Exchange (ETDEWEB)

    Kinchin, G. H. [Atomic Energy Establishment, Winfrith, Dorchester, Dorset (United Kingdom)

    1967-09-15

    A substantial programme of experimental reactor physics work with plutonium fuels has been carried out in the UK; the purpose of this paper is to review the experimental and theoretical work, with emphasis on plutonium recycling in thermal reactors. Although the main incentive for some of the work may have been to study plutonium build-up in uranium-fuelled reactors, it is nevertheless relevant to plutonium recycling and no distinction is drawn between build-up and enrichment studies. A variety of techniques have been for determining reactivity, neutron spectrum and reaction rates in simple assemblies of plutonium-aluminium fuel with water, graphite and beryllia moderators. These experiments give confidence in the basic data and methods of calculation for near-homogeneous mixtures of plutonium and moderator. In the practical case of plutonium recycling it is necessary to confirm that satisfactory predictions can be made for heterogeneous lattices enriched with plutonium. In this field, experiments have been carried out with plutonium-uranium metal and oxide-cluster fuels in graphite-moderated lattices and in SGHW lattices, and the effects of {sup 240}Pu have been studied by perturbation measurements with single fuel elements. The exponential and critical experiments have used tonne quantities of fuel with plutonium contents ranging from 0.25 to 1.2% and the perturbation experiments have extended both the range of plutonium contents and the range of isotopic compositions of plutonium. In addition to reactivity and reactivity coefficients, such as the temperature coefficients, attention has been concentrated on relative reaction rate distributions which provide evidence for variations of neutron spectrum. .Theoretical comparisons, together with similar comparisons for non-uniform lattices, establish the validity of methods of calculation which have been used to study the feasibility of plutonium recycling in thermal reactors. (author)

  19. The radiological hazard of plutonium isotopes and specific plutonium mixtures

    International Nuclear Information System (INIS)

    Heindel, G.; Clow, J.; Inkret, W.; Miller, G.

    1995-11-01

    The US Department of Energy defines the hazard categories of its nuclear facilities based upon the potential for accidents to have significant effects on specific populations and the environment. In this report, the authors consider the time dependence of hazard category 2 (significant on-site effects) for facilities with inventories of plutonium isotopes and specific weapons-grade and heat-source mixtures of plutonium isotopes. The authors also define relative hazard as the reciprocal of the hazard category 2 threshold value and determine its time dependence. The time dependence of both hazard category 2 thresholds and relative hazards are determined and plotted for 10,000 years to provide useful information for planning long-term storage or disposal facilities

  20. Plutonium vulnerability issues at Hanford's Plutonium Finishing Plant

    International Nuclear Information System (INIS)

    Feldt, E.; Templeton, D.W.; Tholen, E.

    1995-01-01

    The Plutonium Finishing Plant (PFP) at the Hanford, Washington Site was operated to produce plutonium (Pu) metal and oxide for national defense purposes. Due to the production requirements and methods utilized to meet national needs and the abrupt shutdown of the plant in the late 1980s, the plant was left in a condition that poses a risk of radiation exposure to plant workers, of accidental radioactive material release to the environment, and of radiation exposure to the public. In early 1994, an Environmental Impact Statement (EIS) to determine the best methods for cleaning out and stabilizing Pu materials in the PFP was started. While the EIS is being prepared, a number of immediate actions have been completed or are underway to significantly reduce the greatest hazards in the PFP. Recently, increased attention his been paid to Pu risks at Department of Energy (DOE) facilities resulting in the Department-wide Plutonium Vulnerability Assessment and a recommendation by the Defense Nuclear Facilities Safety Board (DNFSB) for DOE to develop integrated plans for managing its nuclear materials

  1. Valence-Dependent Belief Updating: Computational Validation

    Directory of Open Access Journals (Sweden)

    Bojana Kuzmanovic

    2017-06-01

    Full Text Available People tend to update beliefs about their future outcomes in a valence-dependent way: they are likely to incorporate good news and to neglect bad news. However, belief formation is a complex process which depends not only on motivational factors such as the desire for favorable conclusions, but also on multiple cognitive variables such as prior beliefs, knowledge about personal vulnerabilities and resources, and the size of the probabilities and estimation errors. Thus, we applied computational modeling in order to test for valence-induced biases in updating while formally controlling for relevant cognitive factors. We compared biased and unbiased Bayesian models of belief updating, and specified alternative models based on reinforcement learning. The experiment consisted of 80 trials with 80 different adverse future life events. In each trial, participants estimated the base rate of one of these events and estimated their own risk of experiencing the event before and after being confronted with the actual base rate. Belief updates corresponded to the difference between the two self-risk estimates. Valence-dependent updating was assessed by comparing trials with good news (better-than-expected base rates with trials with bad news (worse-than-expected base rates. After receiving bad relative to good news, participants' updates were smaller and deviated more strongly from rational Bayesian predictions, indicating a valence-induced bias. Model comparison revealed that the biased (i.e., optimistic Bayesian model of belief updating better accounted for data than the unbiased (i.e., rational Bayesian model, confirming that the valence of the new information influenced the amount of updating. Moreover, alternative computational modeling based on reinforcement learning demonstrated higher learning rates for good than for bad news, as well as a moderating role of personal knowledge. Finally, in this specific experimental context, the approach based on

  2. Bibliography on plutonium and its compounds; Bibliographie sur le plutonium et ses composes

    Energy Technology Data Exchange (ETDEWEB)

    Dirian, J; Choquet, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1958-07-01

    Collection of bibliographical references on plutonium and its principal compounds from 1942 to end of 1957. (author) [French] Compilation de references bibliographiques sur le plutonium et ses principaux composes de 1942 a fin 1957. (auteur)

  3. Multi-generational stewardship of plutonium

    International Nuclear Information System (INIS)

    Pillay, K.K.S.

    1997-01-01

    The post-cold war era has greatly enhanced the interest in the long-term stewardship of plutonium. The management of excess plutonium from proposed nuclear weapons dismantlement has been the subject of numerous intellectual discussions during the past several years. In this context, issues relevant to long-term management of all plutonium as a valuable energy resource are also being examined. While there are differing views about the future role of plutonium in the economy, there is a recognition of the environmental and health related problems and proliferation potentials of weapons-grade plutonium. The long-term management of plutonium as an energy resource will require a new strategy to maintain stewardship for many generations to come

  4. Plutonium Immobilization Can Loading Concepts

    International Nuclear Information System (INIS)

    Kriikku, E.; Ward, C.; Stokes, M.; Randall, B.; Steed, J.; Jones, R.; Hamilton, L.; Rogers, L.; Fiscus, J.; Dyches, G.

    1998-05-01

    The Plutonium Immobilization Facility will encapsulate plutonium in ceramic pucks and seal the pucks inside welded cans. Remote equipment will place these cans in magazines and the magazines in a Defense Waste Processing Facility (DWPF) canister. The DWPF will fill the canister with glass for permanent storage. This report discusses five can loading conceptual designs and the lists the advantages and disadvantages for each concept. This report identifies loading pucks into cans and backfilling cans with helium as the top priority can loading development areas. The can loading welder and cutter are very similar to the existing Savannah River Site (SRS) FB-Line bagless transfer welder and cutter and thus they are a low priority development item

  5. The chemistry of plutonium revealed

    International Nuclear Information System (INIS)

    Connick, R.E.

    1990-01-01

    In 1941 one goal of the Manhattan Project was to unravel the chemistry of the synthetic element plutonium as rapidly as possible. Important insights were obtained from tracer experiments, but the full complexity of plutonium chemistry was not revealed until macroscopic amounts (milligrams) became available. Because processes for separation from fission products were aqueous solution based, such solution chemistry was emphasized, particularly precipitation and oxidation-reduction behavior. The latter turned out to be unusually intricate when it was discovered that two more oxidation states existed in aqueous solution than had previously been suspected. Further, it was found that an equilibrium was rapidly established among the four aqueous oxidation states while at the same time any three were not in equilibrium. These and other observations made while doing a crash study of a previously unknown element will be reported

  6. Plutonium chemistry of the ocean

    International Nuclear Information System (INIS)

    Folsom, T.R.

    1972-01-01

    Plutonium is a man-made element whose behavior in the marine environment is inadequately known at present. It has been studied intensively in connection with production of weapons and power sources and has been characterized as an extremely toxic substance. Nevertheless, only a few dozen measurements have been made of concentrations in seawater and in the associated organisms and sediments. The first of these were as recent as 1964. There are reasons to believe its chemical behavior in the ocean is different from what has been observed on land, and that it will be difficult to predict how plutonium will distribute itself in the ocean. The consequences of increased environmental concentrations of Pu are discussed

  7. The first milligrams of plutonium

    International Nuclear Information System (INIS)

    Goldschmidt, B.

    1997-01-01

    A historical review of the development of the very first quantities of plutonium produced during World War II in the United States and in Canada, as remembered by the French nuclear chemist, Mr Goldschmidt, who participated to the various programs which were involved in the development of the atomic bomb, and to the first steps of the French atomic program after the war. Mr Goldschmidt worked especially on organic solvent extraction, with the selection, in 1945, of non volatile tri glycol dichloride, and the development of the Chalk River plant. In 1949, at the Bouchet plant, his team has isolated the first milligrams of French plutonium from uranium oxide; and in 1952, the PUREX process was developed

  8. Evaluative conditioning induces changes in sound valence

    Directory of Open Access Journals (Sweden)

    Anna C. Bolders

    2012-04-01

    Full Text Available Evaluative Conditioning (EC has hardly been tested in the auditory domain, but it is a potentially valuable research tool. In Experiment 1 we investigated whether the affective evaluation of short environmental sounds can be changed using affective words as unconditioned stimuli (US. Congruence effects on an affective priming task (APT for conditioned sounds demonstrated successful EC. Subjective ratings for sounds paired with negative words changed accordingly. In Experiment 2 we investigated whether the acquired valence remains stable after repeated presentation of the conditioned sound without the US or whether extinction occurs. The acquired affective value remained present, albeit weaker, even after 40 extinction trials. These results warrant the use of EC to study processing of short environmental sounds with acquired valence, even if this requires repeated stimulus presentations. This paves the way for studying processing of affective environmental sounds while effectively controlling low level-stimulus properties.

  9. Confinement facilities for handling plutonium

    International Nuclear Information System (INIS)

    Maraman, W.J.; McNeese, W.D.; Stafford, R.G.

    1975-01-01

    Plutonium handling on a multigram scale began in 1944. Early criteria, equipment, and techniques for confining contamination have been superseded by more stringent criteria and vastly improved equipment and techniques for in-process contamination control, effluent air cleaning and treatment of liquid wastes. This paper describes the evolution of equipment and practices to minimize exposure of workers and escape of contamination into work areas and into the environment. Early and current contamination controls are compared. (author)

  10. Safe handling of plutonium in research laboratories

    International Nuclear Information System (INIS)

    1976-01-01

    The training film illustrates the main basic requirements for the safe handling of small amounts of plutonium. The film is intended not only for people setting up plutonium research laboratories but also for all those who work in existing plutonium research laboratories. It was awarded the first prize in the category ''Protection of Workers'' at the international film festival organized by the 4th World Congress of the International Radiation Protection Association (IRPA) in Paris in April 1977

  11. Addressing mixed waste in plutonium processing

    International Nuclear Information System (INIS)

    Christensen, D.C.; Sohn, C.L.; Reid, R.A.

    1991-01-01

    The overall goal is the minimization of all waste generated in actinide processing facilities. Current emphasis is directed toward reducing and managing mixed waste in plutonium processing facilities. More specifically, the focus is on prioritizing plutonium processing technologies for development that will address major problems in mixed waste management. A five step methodological approach to identify, analyze, solve, and initiate corrective action for mixed waste problems in plutonium processing facilities has been developed

  12. Plutonium recycle. In-core fuel management

    International Nuclear Information System (INIS)

    Vincent, F.; Berthet, A.; Le Bars, M.

    1985-01-01

    Plutonium recycle in France will concern a dozen of PWR 900 MWe controlled in gray mode till 1995. This paper presents the main characteristics of fuel management with plutonium recycle. The organization of management studies will be copied from this developed for classical management studies. Up these studies, a ''feasibility report'' aims at establishing at each stage of the fuel cycle, the impact of the utilization of fuel containing plutonium [fr

  13. Plutonium-induced lymphadenitis in beagles

    International Nuclear Information System (INIS)

    Dagle, G.E.; Park, J.F.

    1976-01-01

    Plutonium oxide particles accumulate in the tracheobronchial lymph nodes of beagles exposed by inhalation and in the popliteal lymph nodes after subcutaneous injection in the hind paws. The sequence of histopathologic changes after phagocytosis of particles included necrosis, increased numbers of macrophages, and fibroplasia. Scar tissue eventually replaced the normal architecture of the lymph nodes and sequestered the plutonium particles from surrounding parenchyma. Electron microscopy showed that plutonium particles were aggregated in phagolysosomes of macrophages

  14. Safe handling of plutonium in research laboratories

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1977-12-31

    The training film illustrates the main basic requirements for the safe handling of small amounts of plutonium. The film is intended not only for people setting up plutonium research laboratories but also for all those who work in existing plutonium research laboratories. It was awarded the first prize in the category ``Protection of Workers`` at the international film festival organized by the 4th World Congress of the International Radiation Protection Association (IRPA) in Paris in April 1977

  15. Weapons-grade plutonium dispositioning. Volume 4

    International Nuclear Information System (INIS)

    Sterbentz, J.W.; Olsen, C.S.; Sinha, U.P.

    1993-06-01

    This study is in response to a request by the Reactor Panel Subcommittee of the National Academy of Sciences (NAS) Committee on International Security and Arms Control (CISAC) to evaluate the feasibility of using plutonium fuels (without uranium) for disposal in existing conventional or advanced light water reactor (LWR) designs and in low temperature/pressure LWR designs that might be developed for plutonium disposal. Three plutonium-based fuel forms (oxides, aluminum metallics, and carbides) are evaluated for neutronic performance, fabrication technology, and material and compatibility issues. For the carbides, only the fabrication technologies are addressed. Viable plutonium oxide fuels for conventional or advanced LWRs include plutonium-zirconium-calcium oxide (PuO 2 -ZrO 2 -CaO) with the addition of thorium oxide (ThO 2 ) or a burnable poison such as erbium oxide (Er 2 O 3 ) or europium oxide (Eu 2 O 3 ) to achieve acceptable neutronic performance. Thorium will breed fissile uranium that may be unacceptable from a proliferation standpoint. Fabrication of uranium and mixed uranium-plutonium oxide fuels is well established; however, fabrication of plutonium-based oxide fuels will require further development. Viable aluminum-plutonium metallic fuels for a low temperature/pressure LWR include plutonium aluminide in an aluminum matrix (PuAl 4 -Al) with the addition of a burnable poison such as erbium (Er) or europium (Eu). Fabrication of low-enriched plutonium in aluminum-plutonium metallic fuel rods was initially established 30 years ago and will require development to recapture and adapt the technology to meet current environmental and safety regulations. Fabrication of high-enriched uranium plate fuel by the picture-frame process is a well established process, but the use of plutonium would require the process to be upgraded in the United States to conform with current regulations and minimize the waste streams

  16. Plutonium in a grassland ecosystem

    International Nuclear Information System (INIS)

    Little, C.A.

    1976-08-01

    A study was made of plutonium contamination of grassland at the Rocky Flats plant northwest of Denver, Colorado. Of interest were: the definition of major plutonium-containing ecosystem compartments; the relative amounts in those compartments; how those values related to studies done in other geographical areas; whether or not the predominant isotopes, 238 Pu and 239 Pu, behaved differently; and what mechanisms might have allowed for the observed patterns of contamination. Samples of soil, litter, vegetation, arthropods, and small mammals were collected for Pu analysis and mass determination from each of two macroplots. Small aliquots (5 g or less) were analyzed by a rapid liquid scintillation technique and by alpha spectrometry. Of the compartments sampled, greater than 99 percent of the total plutonium was contained in the soil and the concentrations were significantly inversely correlated with distance from the contamination source, depth of the sample, and particle size of the sieved soil samples. The soil data suggested that the distribution of contamination largely resulted from physical transport processes

  17. Human Amygdala Represents the Complete Spectrum of Subjective Valence

    Science.gov (United States)

    Jin, Jingwen; Zelano, Christina; Gottfried, Jay A.

    2015-01-01

    Although the amygdala is a major locus for hedonic processing, how it encodes valence information is poorly understood. Given the hedonic potency of odor stimuli and the amygdala's anatomical proximity to the peripheral olfactory system, we combined high-resolution fMRI with pattern-based multivariate techniques to examine how valence information is encoded in the amygdala. Ten human subjects underwent fMRI scanning while smelling 9 odorants that systematically varied in perceived valence. Representational similarity analyses showed that amygdala codes the entire dimension of valence, ranging from pleasantness to unpleasantness. This unidimensional representation significantly correlated with self-reported valence ratings but not with intensity ratings. Furthermore, within-trial valence representations evolved over time, prioritizing earlier differentiation of unpleasant stimuli. Together, these findings underscore the idea that both spatial and temporal features uniquely encode pleasant and unpleasant odor valence in the amygdala. The availability of a unidimensional valence code in the amygdala, distributed in both space and time, would create greater flexibility in determining the pleasantness or unpleasantness of stimuli, providing a mechanism by which expectation, context, attention, and learning could influence affective boundaries for guiding behavior. SIGNIFICANCE STATEMENT Our findings elucidate the mechanisms of affective processing in the amygdala by demonstrating that this brain region represents the entire valence dimension from pleasant to unpleasant. An important implication of this unidimensional valence code is that pleasant and unpleasant valence cannot coexist in the amygdale because overlap of fMRI ensemble patterns for these two valence extremes obscures their unique content. This functional architecture, whereby subjective valence maps onto a pattern continuum between pleasant and unpleasant poles, offers a robust mechanism by which context

  18. 5th International Conference on Valence Fluctuations

    CERN Document Server

    Malik, S

    1987-01-01

    During the Koln meeting (August 28-31, 1984), Irdia was chosen as the venue for the next International Conference on Valence Fluctuations. lhis was in recognition ard appreciation of the work done, both experimental ard theoretical, by the Irdian scientists in this area during the last decade. We decided to hold this Conference in the month of January, 1987 at Bangalore. lhe subject of Valence Fluctuations has kept itself alive ard active as it has provided many shocks ard suprises particularly among the Ce- ard U-based intermetallies. lhe richness of many interesting physical phenomena occurring in mixed valent materials, the flexibility of modifying their physical properties (by alloying, for example) ard the possibility of synthesizing a wide variety of new such materials seem to be the key factors in this regard. Barely six months before this Conference, an International Conference on Anomalous Rare Earths and Actinides (ICAREA) had been held at Grenoble (July, 1986) which also focussed on mixed valence a...

  19. Valence fluctuations between two magnetic configurations

    International Nuclear Information System (INIS)

    Mazzaferro, J.O.

    1982-01-01

    The subject of this work is the study of a microscopic model which describes TmSe through its most important feature, i.e.: the valence fluctuations between two magnetic configurations. Chapter I is a general review of the most important physical properties of rare-earth systems with intermediate valence (I.V.) and a general description of experimental results and theoretical models on Tm compounds. In Chapter II the Hamiltonian model is discussed and the loss of rotational invariance is also analyzed. Chapter III is devoted to the study of non-stoichiometric Tsub(x)Se compounds. It is shown that these compounds can be considered as a mixture of TmSe (I.V. system) and Tm 3+ 0.87Se. Chapter IV is devoted to the calculation of spin-and charge susceptibilities. The results obtained permit to explain the essential features of the neutron scattering spectrum in TmSe. In Chapter V, an exactly solvable periodic Hamiltonian is presented. From the experimental results, some fundamental features are deduced to describe TmSe as an intermediate valence system whose two accessible ionic configurations are magnetic (degenerated fundamental state). (M.E.L) [es

  20. An Improved Plutonium Trifluoride Precipitation Flowsheet

    Energy Technology Data Exchange (ETDEWEB)

    Harmon, H.D.

    2001-06-26

    This report discusses results of the plutonium trifluoride two-stage precipitation study. A series of precipitation experiments was used to identify the significant process variables affecting precipitation performance. A mathematical model of the precipitation process was developed which is based on the formation of plutonium fluoride complexes. The precipitation model relates all process variables, in a single equation, to a single parameter which can be used to control the performance of the plutonium trifluoride precipitation process. Recommendations have been made which will optimize the FB-Line plutonium trifluoride precipitation process.

  1. Safe handling of plutonium: a panel report

    Energy Technology Data Exchange (ETDEWEB)

    1974-01-01

    This guide results from a meeting of a Panel of Experts held by the International Atomic Energy Agency on 8 to 12 November 1971. It is directed to workers in research laboratories handling plutonium in gram amounts. Contents: aspects of the physical and chemical properties of plutonium; metabolic features of plutonium; facility design features for safe handling of plutonium (layout of facility, working zones, decontamination room, etc.); glove boxes; health surveillance (surveillance of environment and supervision of workers); emergencies; organization. Annexes: types of glove boxes; tables; mobile ..cap alpha.. air sampler; aerosol monitor; bio-assay limits of detection; examples of contamination control monitors.

  2. Plutonium use in foreign countries (03)

    International Nuclear Information System (INIS)

    Otagaki, Takao

    2004-03-01

    European countries and Japan had been implementing the strategy of spent fuel reprocessing in order to use nuclear material to the maximum. Plutonium recovered from reprocessing, however, must be recycle on light water reactors (LWRs) because of considerable delay of fast reactor development. In Europe, much of experiences of plutonium recycling have been accumulated until now. Thus, the status of plutonium recycling up to the end of 2003 in France, Germany, The U.K., Belgium, Switzerland and other countries were studied based on the following scope. (1) Basic policy and present status of plutonium recycling in primary countries of France, Germany, The U.K., Belgium, Switzerland, and Sweden which plans to recycle a part of plutonium: Backend policy and the status of spent fuel management were studied, then integrated analysis and evaluation of the position of plutonium recycling in backend and the status of plutonium recycling development were performed. (2) Plan and experience of Mixed Oxide (MOX) fuel fabrication and reprocessing of spent fuels: The data and information on plan and experience of MOX fuel fabrication and reprocessing in foreign countries were collected. (3) Plutonium inventories: The data and information of plutonium inventories of foreign countries were collected. (author)

  3. Plutonium use in foreign countries (01)

    International Nuclear Information System (INIS)

    Otagaki, Takao

    2002-03-01

    European countries and Japan had been implementing the strategy of spent fuel reprocessing in order to use nuclear material to the maximum. Plutonium recovered from reprocessing, however, must be recycle on light water reactors (LWRs) because of considerable delay of fast reactor development. In Europe, much of experience of plutonium recycling have been accumulated until now. Thus, the status of plutonium recycling up to the end of 2001 in France, Germany, The U.K., Belgium, Switzerland and other countries were studied based on the following scope. (1) Basic policy and present status of plutonium recycling in primary countries of France, Germany, The U.K., Belgium, Switzerland, and Sweden which recently appears the move of recycling a part of plutonium. Backend policy and the status of spent fuel management were studied, then integrated analysis and evaluation of the position of plutonium recycling in backend and the status of plutonium recycling development were performed. (2) Plan and experience of Mixed Oxide (MOX) fuel fabrication and reprocessing of spent fuels. The data and information on plan and experience of MOX fuel fabrication and reprocessing in foreign countries were collected. (3) Plutonium inventories. The data and information on plutonium inventories of foreign countries were collected. (author)

  4. Plutonium use in foreign countries (99)

    International Nuclear Information System (INIS)

    Otagaki, Takao

    2000-03-01

    European countries and Japan had been implementing the strategy of spent fuel reprocessing in order to use nuclear material to the maximum. Plutonium recovered from reprocessing, however, must be recycle on light water reactors (LWRs) because of considerable delay of fast reactor development. In Europe, much of experience of plutonium recycling have been accumulated until now. Thus, the status of plutonium recycling up to the end of 1999 in France, Germany, The U.K., Belgium, Switzerland and other countries were studied based on the following scope. (1) Basic policy and present status of plutonium recycling in primary countries of France, Germany, The U.K., Belgium, Switzerland, and Sweden which recently appears the move to recycling a part of plutonium backend policy and the status of spent fuel management were studied, then integrated analysis and evaluation of the position of plutonium recycling in backend and the status of plutonium recycling development were performed. (2) Plan and experience of Mixed Oxide (MOX) fuel fabrication and reprocessing of spent fuels. The data and information on plan and experience of MOX fuel fabrication and reprocessing in foreign countries were collected. (3) Plutonium inventories. The data and information on plutonium inventories of foreign counties were collected. (author)

  5. Plutonium use in foreign countries (02)

    International Nuclear Information System (INIS)

    Otagaki, Takao

    2003-02-01

    European countries and Japan had been implementing the strategy of spent fuel reprocessing in order to use nuclear material to the maximum. Plutonium recovered from reprocessing, however, must be recycle on light water reactors (LWRs) because of considerable delay of fast reactor development. In Europe, much of experience of plutonium recycling have been accumulated until now. Thus, the status of plutonium recycling up to the end of 2002 in France, Germany, The U.K., Belgium, Switzerland and other countries were studied based on the following scope. (1) Basic policy and present status of plutonium recycling in primary countries of France, Germany, The U.K., Belgium, Switzerland, and Sweden which recently appears the move of recycling a part of plutonium. Backend policy and the status of spent fuel management were studied, then integrated analysis and evaluation of the position of plutonium recycling in backend and the status of plutonium recycling development were performed. (2) Plan and experience of Mixed Oside (MOX) fuel fabrication and reprocessing of spent fuels. The data and information on plan and experience of MOX fuel fabrication and reprocessing in foreign countries were collected. (3) Plutonium inventories. The data and information on plutonium inventories of foreign countries were collected. (author)

  6. Plutonium use in foreign countries. (04)

    International Nuclear Information System (INIS)

    Otagaki, Takao

    2005-03-01

    European countries and Japan had been implementing the strategy of spent fuel reprocessing in order to use nuclear material to the maximum. Plutonium recovered from reprocessing, however, must be recycle on light water reactors (LWRs) because of considerable delay of fast reactor development. In Europe, much of experience of plutonium recycling have been accumulated until now. Thus, the status of plutonium recycling up to the end of 2004 in France, Germany, The U.K., Belgium, Switzerland and other countries were studied based on the following scope. (1) Basic policy and present status of plutonium recycling in primary countries of France, Germany, the U.K., Belgium, Switzerland, and Sweden which plans to recycle a limited amount of plutonium: Backend policy and the status of spent fuel management were studied, then integrated analysis and evaluation of the position of plutonium recycling in backend and the status of plutonium recycling development were performed. (2) Plan and experience of Mixed Oxide (MOX) fuel fabrication and reprocessing of spent fuels: The data and information on plan and experience of MOX fuel fabrication and reprocessing in foreign countries were collected. (3) Plutonium inventories: The data and information on plutonium inventories of foreign countries were collected. (author)

  7. An Improved Plutonium Trifluoride Precipitation Flowsheet

    International Nuclear Information System (INIS)

    Harmon, H.D.

    2001-01-01

    This report discusses results of the plutonium trifluoride two-stage precipitation study. A series of precipitation experiments was used to identify the significant process variables affecting precipitation performance. A mathematical model of the precipitation process was developed which is based on the formation of plutonium fluoride complexes. The precipitation model relates all process variables, in a single equation, to a single parameter which can be used to control the performance of the plutonium trifluoride precipitation process. Recommendations have been made which will optimize the FB-Line plutonium trifluoride precipitation process

  8. Assay of low-level plutonium effluents

    International Nuclear Information System (INIS)

    Hsue, S.T.; Hsue, F.; Bowersox, D.F.

    1981-01-01

    In the plutonium recovery section at the Los Alamos National Laboratory, an effluent solution is generated that contains low plutonium concentration and relatively high americium concentration. Nondestructive assay of this solution is demonstrated by measuring the passive L x-rays following alpha decay. Preliminary results indicate that an average deviation of 30% between L x-ray and alpha counting can be achieved for plutonium concentrations above 10 mg/L and Am/Pu ratios of up to 3; for plutonium concentrations less than 10 mg/L, the average deviation is 40%. The sensitivity of the L x-ray assay is approx. 1 mg Pu/L

  9. The plutonium challenge for the future

    International Nuclear Information System (INIS)

    Gray, L.W.

    2000-01-01

    In this paper author deal with the weapons-usable plutonium and with the possibilities of their managing. Russia has not disclosed the amount of plutonium produced, but various estimates indicate that the production was about 130 tonnes. Production has been curtailed in Russia; three dual-purpose reactors still produce weapons-grade plutonium - two at Tomsk-7 (renamed Seversk) and one at Krasnoyarsk-26 (renamed Zheleznogorsk Mining and Chemical Combine). In a 1994 United States-Russian agreement that has yet to enter into force, Russia agreed to close the remaining operating reactors by the year 2000. Treaties between the United States and Russia have already cut the number of nuclear warheads from more than 10,000 to about 6,000 under START 1, which has been ratified, and to about 3,500 under START 2, which still awaits approval. If Russia and the United States conclude START 3, that number could drop to between 2,000 and 2,500. On September 2, 1998, the Presidents of the United States and Russia signed the 'Joint statement of principles for Management and Disposition of Plutonium, Designated as No Longer Required for Defense Purposes.' In this joint statement the Presidents affirm the intention of each country to remove by stages approximately 50 metric tons of plutonium and to convert the nuclear weapons programs, and to convert this material so that it can never be used in nuclear weapons. These 100 tonne of plutonium must be managed in proper way such that it becomes neither a proliferation for an environmental risk. The United States has proposed that it manage it's 50 tonnes by a dual approach-once through MOX burning of a portion of the plutonium and immobilization in a ceramic matrix followed by en- casement in high level waste glass. Russia has proposed that it manage its full 50 tonnes by burning in a reactor. The MOX program in the United States would bum the cleaner plutonium metal and residues. Weapons components would be converted to plutonium oxide

  10. Decontaminaion of metals containing plutonium and americium

    International Nuclear Information System (INIS)

    Seitz, M.G.; Gerding, T.J.; Steindler, M.J.

    1979-06-01

    Melt-slagging (melt-refining) techniques were evaluated as a decontamination and consolidation step for metals contaminated with oxides of plutonium and americium. Experiments were performed in which mild steel, stainless steel, and nickel contaminated with oxides of plutonium and americium were melted in the presence of silicate slags of various compositions. The metal products were low in contamination, with the plutonium and americium strongly fractionated to the slags. Partition coefficients (plutonium in slag/plutonium in steel) of 7 x 10 6 were measured with boro-silicate slag and of 3 x 10 6 with calcium, magnesium silicate slag. Decontamination of metals containing as much as 14,000 ppM plutonium appears to be as efficient as for metals with plutonium levels of 400 ppM. Staged extraction, that is, a remelting of processed metal with clean slag, results in further decontamination of the metal. The second extraction is effective with either resistance-furnace melting or electric-arc melting. Slag adhering to the metal ingots and in defects within the ingots is in the important contributors to plutonium retained in processed metals. If these sources of plutonium are controlled, the melt-refining process can be used on a large scale to convert highly contaminated metals to homogeneous and compact forms with very low concentrations of plutonium and americium. A conceptual design of a melt-refining process to decontaminate plutonium- and americium-contaminated metals is described. The process includes single-stage refining of contaminated metals to produce a metal product which would have less than 10 nCi/g of TRU-element contamination. Two plant sizes were considered. The smaller conceptual plant processes 77 kg of metal per 8-h period and may be portable.The larger one processes 140 kg of metal per 8-h period, is stationary, and may be near te maximum size that is practical for a metal decontamination process

  11. Asymmetric adjustment

    NARCIS (Netherlands)

    2010-01-01

    A method of adjusting a signal processing parameter for a first hearing aid and a second hearing aid forming parts of a binaural hearing aid system to be worn by a user is provided. The binaural hearing aid system comprises a user specific model representing a desired asymmetry between a first ear

  12. Plutonium in domestic animals and man

    International Nuclear Information System (INIS)

    Coughtrey, P.J.; Jackson, D.; Jones, C.H.; Kane, P.; Thorne, M.C.

    1984-01-01

    This chapter deals with plutonium adsorption, retention and translocation rates in lungs, the gastrointestinal tract, liver and in body tissues of domestic animals and man. Urinary and faecal excretion of plutonium is discussed. Transfer rates to eggs, milk, foetus and newborn are considered. Of all these subjects, data are presented extracted from literature and cast in tables

  13. Two-stage precipitation of plutonium trifluoride

    International Nuclear Information System (INIS)

    Luerkens, D.W.

    1984-04-01

    Plutonium trifluoride was precipitated using a two-stage precipitation system. A series of precipitation experiments identified the significant process variables affecting precipitate characteristics. A mathematical precipitation model was developed which was based on the formation of plutonium fluoride complexes. The precipitation model relates all process variables, in a single equation, to a single parameter that can be used to control particle characteristics

  14. Plutonium production and utilization forecasts in Europe

    International Nuclear Information System (INIS)

    Haijtink, B.

    1976-01-01

    The planned accelerated growth of nuclear energy generation in the near future will lead to a large production of plutonium in the thermal reactors. Therefore, up to 1985, the major part of the available plutonium will be plutonium recovered from spent uranium-metal, particularly in the United Kingdom and in France. Because of the low demand for fuelling the fast breeder reactors within the near future, a surplus of fissile plutonium will be accumulated in Europe. Even if the planned availability of the oxide reprocessing capacity will be delayed with two or three years, a plutonium surplus will still exist in Europe, e.g.; in 1985: 25-20 tons. On longer term, up to 2000, the plutonium production in thermal reactors will be sufficient to meet the estimated demand for fast breeder reactors at their commercial introduction foreseen for the nineties. That means that all the plutonium surplus needs not to be stocked for use in fast breeder reactors later on but could be recycled in thermal reactors. The magnitude of the available fissionable materials give an idea of the importance to promote, on an industrial scale, the plutonium recycling technology

  15. Plutonium in the Gulf of Mexico

    International Nuclear Information System (INIS)

    Scott, M.R.; Salter, P.F.

    The geochemistry of fallout plutonium in the sediments of the Gulf of Mexico was studied. A series of sediment cores was collected in a traverse from the deep Gulf of Mexico to the Mississippi Delta. The cores were sliced into 1 cm intervals and analyzed for plutonium. Explanations for the variations in concentration are presented

  16. The transport of civil plutonium by air

    International Nuclear Information System (INIS)

    1988-01-01

    The paper presents the review entitled ''The Transport of Civil Plutonium by Air'' reported by the Advisory Committee on the Safe Transport of Radioactive Materials (ACTRAM) 1988. The contents contain chapters on the following topics:- the reasons for air transport, the various regulations, packagings for plutonium transport, testing of the packagings, accidents, the consequences of a release, and emergency arrangements. (U.K.)

  17. Ventilation design for new plutonium recovery facility

    International Nuclear Information System (INIS)

    Oliver, A.J.; Amos, C.L.

    1975-01-01

    In 1972 the Atomic Energy Commission (AEC) issued revised guidelines on ''Minimum Design Criteria for New Plutonium Facilities.'' With these criteria as guidelines, a new Plutonium Recovery Facility is being designed and constructed at the AEC Rocky Flats Plant. The methods by which the confinement of contamination and air treatment are being handled in this facility are described. (U.S.)

  18. Valence skipping driven superconductivity and charge Kondo effect

    International Nuclear Information System (INIS)

    Yanagisawa, Takashi; Hase, Izumi

    2013-01-01

    Highlights: •Valence skipping in metallic compounds can give rise to an unconventional superconductivity. •Several elements in the periodic table show valence skipping (or valence missing), for example, Bi forms the compounds in valence states +3 and +5. •The doping of valence skipping elements will induce superconductivity and this will lead to a possibility of high temperature superconductivity. •We consider the Wolf model with negative-U impurities, and show a phase diagram including superconducting phase. •There is a high temperature region near the boundary. -- Abstract: Valence skipping in metallic compounds can give rise to an unconventional superconductivity. Several elements in the periodic table show valence skipping (or valence missing), for example, Bi forms the compounds in valence states +3 and +5. The doping of valence skipping elements will induce superconductivity and this will lead to a possibility of high temperature superconductivity. We consider the Wolf model with negative-U impurities, and show a phase diagram including superconducting phase. The superconducting state is changed into a metallic state with a local singlet as the attractive interaction |U| increases. There is a high temperature region near the boundary

  19. Plutonium use - present status and perspectives

    International Nuclear Information System (INIS)

    Dievoet, J. van; Fossoul, E.; Jonckheere, E.; Bemden, E. van den

    1977-01-01

    Plutonium is being produced in increasing quantities in the so-called proven reactors, which are mostly of the light-water type. Evaluation of this production on a world scale shows that it would be theoretically possible to construct a large number of breeders and thus to make the best use of the intrinsic qualities of plutonium as a fissionable material, while considerably reducing the consumption of uranium. This source of plutonium is nevertheless dependent on an essential stage of the fuel cycle, namely reprocessing of irradiated fuel. The long delays in installing an adequate world reprocessing capacity are substantially weakening the prospects for the introduction of breeders. Furthermore, the critical situation as regards reprocessing may delay the development of complementary reprocessing methods for fuels with a high plutonium content and high burn-up. When it is recalled that fast reactors themselves may suffer some delay in their technological development, if only because of the intention to build power plants of very high unit capacity immediately, it must be concluded that another use will have to be considered for the plutonium available in future -use in thermal reactors, i.e. recycling. The recycling of plutonium is a well-known technique today and the objections which could be raised against it hardly stand up to analysis. Utilization of plutonium offers an appreciable saving in terms of uranium and separative work units, the consumption being of a low order of magnitude in comparison with the total amount of plutonium needed for the eventual fabrication of the first fast reactor cores. It can also be shown that immediate reprocessing of the recycling fuel is not essential for the economics of the concept. Temporary storage of recycled fuel has the advantage of concentrating plutonium in a particularly safe form, namely in irradiated plutonium-bearing fuel assemblies. Lastly, recycling offers such flexibility that it does not in practice represent

  20. Constitutional problems in the handling of plutonium

    International Nuclear Information System (INIS)

    Witt, S. de.

    1989-01-01

    Reprocessing and final storage involve two different systems of nuclear energy utilization: with or without the use of plutonium. There is a choice available between these two systems. The paper discusss the constitutional implications of this choice. The permission of the use of plutonium as nuclear fuel by the Atomic Energy Law is irreconcilable with the Basic Law, i.e. the Constitution. If the corresponding provisions of the Atomic Energy Law are repealed, then only the plutonium-related branch will be revoked and not the legal permission of nuclear energy as a whole. The fact is not ignored that the Atomic Energy law does not permit the construction and operation of a plant or the handling of plutonium if this were to violate a basic right. However, the plutonium-related branch of nculear energy utilization inevitably results in such basic right violations; hence the Atomic Energy law is unconstitutional in this respect. (orig./HSCH) [de

  1. Nuclear legacy. Democracy in a plutonium economy

    International Nuclear Information System (INIS)

    Barnaby, F.

    1997-01-01

    There have already been a few hundred known incidents of nuclear smuggling, mostly of small quantities not close to weapons grade material - but one gram of plutonium is more than sufficient to cause significant harm and to pose a substantial threat. The potential for further thefts is growing as the world produces ever more quantities of plutonium, not only from the dismantling of nuclear weapons but also from the separation out of plutonium from spent uranium nuclear reactor fuel elements. Trying to prevent the theft of gram quantities of plutonium would require levels of protection and surveillance unacceptably high in a democratic society. It is unlikely, therefore, that democracy could survive in a plutonium economy

  2. Disposing of the world's excess plutonium

    International Nuclear Information System (INIS)

    McCormick, J.M.; Bullen, D.B.

    1998-01-01

    The authors undertake three key objectives in addressing the issue of plutonium disposition at the end of the Cold War. First, the authors estimate the total global inventory of plutonium both from weapons dismantlement and civil nuclear power reactors. Second, they review past and current policy toward handling this metal by the US, Russia, and other key countries. Third, they evaluate the feasibility of several options (but especially the vitrification and mixed oxide fuel options announced by the Clinton administration) for disposing of the increasing amounts of plutonium available today. To undertake this analysis, the authors consider both the political and scientific problems confronting policymakers in dealing with this global plutonium issue. Interview data with political and technical officials in Washington and at the International Atomic Energy Agency in Vienna, Austria, and empirical inventory data on plutonium from a variety of sources form the basis of their analysis

  3. Topological Qubits from Valence Bond Solids

    Science.gov (United States)

    Wang, Dong-Sheng; Affleck, Ian; Raussendorf, Robert

    2018-05-01

    Topological qubits based on S U (N )-symmetric valence-bond solid models are constructed. A logical topological qubit is the ground subspace with twofold degeneracy, which is due to the spontaneous breaking of a global parity symmetry. A logical Z rotation by an angle 2 π /N , for any integer N >2 , is provided by a global twist operation, which is of a topological nature and protected by the energy gap. A general concatenation scheme with standard quantum error-correction codes is also proposed, which can lead to better codes. Generic error-correction properties of symmetry-protected topological order are also demonstrated.

  4. Thermal recombination: Beyond the valence quark approximation

    Energy Technology Data Exchange (ETDEWEB)

    Mueller, B. [Department of Physics, Duke University, Durham, NC 27708 (United States); Fries, R.J. [School of Physics and Astronomy, University of Minnesota, Minneapolis, MN 55455 (United States)]. E-mail: fries@physics.umn.edu; Bass, S.A. [Department of Physics, Duke University, Durham, NC 27708 (United States); RIKEN BNL Research Center, Brookhaven National Laboratory, Upton, NY 11973 (United States)

    2005-07-07

    Quark counting rules derived from recombination models agree well with data on hadron production at intermediate transverse momenta in relativistic heavy-ion collisions. They convey a simple picture of hadrons consisting only of valence quarks. We discuss the inclusion of higher Fock states that add sea quarks and gluons to the hadron structure. We show that, when recombination occurs from a thermal medium, hadron spectra remain unaffected by the inclusion of higher Fock states. However, the quark number scaling for elliptic flow is somewhat affected. We discuss the implications for our understanding of data from the Relativistic Heavy Ion Collider.

  5. Valence electron momentum distributions in cadmium

    International Nuclear Information System (INIS)

    Frost, L.; Weigold, E.; Mitroy, J.

    1982-08-01

    The valence 5s and 4d electron momentum distributions in cadmium have been measured using noncoplanar symmetric (e, 2e) electron coincidence spectroscopy at a total energy of 1200eV. They are in close agreement with Hartree-Fock momentum distributions both in shape and relative magnitudes. Some satellite lines of very low intensity have been detected. A CI calculation of the Cd ground state and several Cd + ion states has been carried out to predict cross reactions for the ground state and various satellite transitions. The predictions are in agreement with the data

  6. Reply to Isgur's comments on valence QCD

    International Nuclear Information System (INIS)

    Liu, K.F.

    2000-01-01

    With the goal of understanding the complexity of QCD and the role of symmetry in dynamics, the authors studied a field theory called Valence QCD (VQCD) in which the Z graphs are forbidden so that the Fock space is limited to the valence quarks. The authors calculated nucleon form factors, matrix elements, and hadron masses both with this theory and with quenched QCD on a set of lattices with the same gauge background. Comparing the results of the lattice calculations in these two theories, the authors drew conclusions regarding the SU(6) valence quark model and chiral symmetry. While recognizing the goal of VQCD, Nathan Isgur disagrees on some of the conclusions the authors have drawn. The foremost objection raised in section 2 is to their suggestion that the major part of the hyperfine splittings in baryons is due to Goldstone boson exchange and not one-gluon-exchange (OGE) interactions. The logic of Isgur's objection is that VQCD yields a spectroscopy vastly different from quenched QCD and therefore the structure of the hadrons (to which hyperfine splittings in a quark model are intimately tied) is also suspect so no definite conclusions are possible. To put this into perspective it should be emphasized at the outset that spectroscopy is only one aspect of hadron physics examined in section 1. The authors have studied the axial and scalar couplings of nucleon in terms of F A /D A and F S /D S , the neutron to proton magnetic moment ratio μn/μp, and various form factors. None of these results reveal any pathologies of hadron structure and turn out to be close to the SU(6) relations, as expected. In fact this is what motivated the study of valence degrees of freedom via VQCD. In section 2 the authors address specific issues related to spectroscopy in VQCD. Isgur also presented more general arguments against the idea of boson exchange as a contributor to hyperfine effects. A cornerstone of his discussion is the unifying aspect of OGE in a quark model picture. The

  7. Plutonium fallout at Fayetteville, AR

    International Nuclear Information System (INIS)

    Sandoval, D.N.; Essien, I.O.; Kuroda, P.K.

    1985-01-01

    It is well established that atmospheric Pu fallout has its origin in the testing of nuclear devices and satellite accidents. Monitoring injections of Pu during the testing of nuclear devices can be useful in characterizing the detonation and subsequently tagging its global fallout. Since Pu uptake pathway into humans is mainly through the respiratory and digestive systems, it is important to know about the behavior of Pu in the atmosphere. Snow and rain samples were collected between Jan 1981 and April 1983, and analyzed for plutonium

  8. Sandia Laboratories plutonium protection system

    International Nuclear Information System (INIS)

    Bernard, E.A.; Miyoshi, D.S.; Gutierrez, F.D.

    1977-01-01

    Sandia Laboratories is developing an improved plutonium protection system (PPS) to demonstrate new concepts for enhancing special nuclear materials safeguards. PPS concepts include separation of functions, real-time item accountability and improved means for control of materials, activities and personnel access. Physical barriers and a secure communications network are designed into the system to offer greater protection against sabotage, diversion and theft attempts. Prototype systems are being constructed at Hanford, Washington and Albuquerque, New Mexico and will be subjected to a comprehensive testing and evaluation program

  9. Inhaled plutonium nitrate in dogs

    International Nuclear Information System (INIS)

    Dagle, G.E.

    1987-01-01

    The major objective of this project is to determine dose-effect relationships of inhaled plutonium nitrate in dogs to aid in predicting health effects of accidental exposure in man. For lifespan dose-effect studies, beagle dogs were given a single inhalation exposure to 239 Pu(NO 3 ) 4 , in 1976 and 1977. The earliest biological effect was on the hematopoietic system; lymphopenia and neutropenia occurred at the two highest dose levels. They have also observed radiation pneumonitis, lung cancer, and bone cancer at the three highest dose levels. 1 figure, 3 tables

  10. Inhaled plutonium nitrate in dogs

    International Nuclear Information System (INIS)

    Dagle, G.E.

    1986-01-01

    The major objective of this project is to determine dose-effect relationships of inhaled plutonium nitrate in dogs to aid in predicting health effects of accidental exposure in man. For lifespan dose-effect studies, beagle dogs were given a single inhalation exposure to 239 Pu(NO 3 ) 4 , in 1976 and 1977. The earliest biological effect was on the hematopoietic system; lymphopenia and neutropenia occurred at the two highest dose levels. The authors have also observed radiation pneumonitis, lung cancer, and bone cancer at the three highest dose levels. 1 figure, 4 tables

  11. Inhaled plutonium nitrate in dogs

    International Nuclear Information System (INIS)

    Dagle, G.E.

    1982-01-01

    The major objective of this project is to determine dose-effect relationships of inhaled plutonium nitrate in dogs to aid in the prediction of health effects of accidental exposure in man. For lifespan dose-effect studies, beagle dogs were given a single inhalation exposure to 239 Pu(NO 3 ) 4 , in 1976 and 1977. The earliest biological effect was on the hematopoietic system; as described in previous Annual Reports, lymphopenia and neutropenia occurred at the two highest dose levels. Radiation pneumonitis, lung cancer, and bone cancer have been observed at the highest dose levels

  12. Waste forms for plutonium disposition

    International Nuclear Information System (INIS)

    Johnson, S.G.; O'Holleran, T.P.; Frank, S.M.; Meyer, M.K.; Hanson, M.; Staples, B.A.; Knecht, D.A.; Kong, P.C.

    1997-01-01

    The field of plutonium disposition is varied and of much importance, since the Department of Energy has decided on the hybrid option for disposing of the weapons materials. This consists of either placing the Pu into mixed oxide fuel for reactors or placing the material into a stable waste form such as glass. The waste form used for Pu disposition should exhibit certain qualities: (1) provide for a suitable deterrent to guard against proliferation; (2) be of minimal volume, i.e., maximize the loading; and (3) be reasonably durable under repository-like conditions. This paper will discuss several Pu waste forms that display promising characteristics

  13. The plutonium mountain: preventing diversion

    International Nuclear Information System (INIS)

    Pohling-Brown, Pamela.

    1997-01-01

    With continued arms-reduction between the USA and the former Soviet Union, surplus nuclear materials, from dismantled weapons, requires handling. A number of risks are identified including occupational safety for workers involved with handling nuclear materials, and environmental protection. Perhaps the most sinister is the extra security needed to ensure that these materials are not diverted to rogue states or terrorist groups, as materials are handled in a larger number of countries. In particular, the author addresses the problem of plutonium reserves, and discusses the role of reprocessing in preventing diversion. (UK)

  14. Dosage of plutonium by isotopic dilution in irradiated fuels; Dosage du plutonium par dilution isotopique dans les combustibles irradies

    Energy Technology Data Exchange (ETDEWEB)

    Lucas, M [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1964-07-01

    Plutonium determination in irradiated fuels has been carried out for several years by isotopic dilution by Sebaci and SSM in collaboration. SECACI has made available to the SSM the necessary space and equipment in its Fontenay laboratories. This work has shown the importance of the valency cycle which should make it possible to obtain a uniform isotopic distribution in sample tracer mixtures, and also a satisfactory U/Pu separation. Now it has been noticed that the presence of an excess of uranium considerably modifies the oxidation-reduction reaction kinetics of the plutonium. We have therefore been led to change certain parts of the operational technique so as to have an efficient cycle and to thereby improve the U/Pu separation; the stability of the thermionic emission of the plutonium, connected to the quantity of residual uranium, has at the same time been improved and we can now carry out more precise isotopic analyses. We have also tried to eliminate as far as possible the isotopic contaminations by:using a more rational operational method; the equipment used has been the object of a special study. The evaporations are carried out so as to prevent the formation of saturated vapours inside the glove box. The material which cannot be changed after each operation is carefully cleaned every time a new sample is treated. With this technique, a second calibration of the tracer T{sub 2} has been undertaken using a new standard solution. This solution has been prepared very carefully by weighing uranium and plutonium of known chemical purity, and we believe that it can be guaranteed to be a good reference solution. The value of the {sup 233}U/{sup 242}Pu ratio of the tracer has been obtained with a relative accuracy of 0,5 per cent. This modified method is now being applied to the analysis of rods irradiated in G-3. (author) [French] La determination du plutonium par dilution isotopique dans les combustibles irradies est pratiquee depuis plusieurs annees en

  15. Salary adjustments

    CERN Multimedia

    HR Department

    2008-01-01

    In accordance with decisions taken by the Finance Committee and Council in December 2007, salaries are adjusted with effect from 1 January 2008. Scale of basic salaries and scale of stipends paid to fellows (Annex R A 5 and R A 6 respectively): increased by 0.71% with effect from 1 January 2008. As a result of the stability of the Geneva consumer price index, following elements do not increase: a) Family Allowance, Child Allowance and Infant Allowance (Annex R A 3). b) Reimbursement of education fees: maximum amounts of reimbursement (Annex R A 4.01) for the academic year 2007/2008. Related adjustments will be implemented, wherever applicable, to Paid Associates and Students. As in the past, the actual percentage increase of each salary position may vary, due to the application of a constant step value and the rounding effects. Human Resources Department Tel. 73566

  16. Salary adjustments

    CERN Multimedia

    HR Department

    2008-01-01

    In accordance with decisions taken by the Finance Committee and Council in December 2007, salaries are adjusted with effect from 1 January 2008. Scale of basic salaries and scale of stipends paid to fellows (Annex R A 5 and R A 6 respectively): increased by 0.71% with effect from 1 January 2008. As a result of the stability of the Geneva consumer price index, the following elements do not increase: a)\tFamily Allowance, Child Allowance and Infant Allowance (Annex R A 3); b)\tReimbursement of education fees: maximum amounts of reimbursement (Annex R A 4.01) for the academic year 2007/2008. Related adjustments will be applied, wherever applicable, to Paid Associates and Students. As in the past, the actual percentage increase of each salary position may vary, due to the application of a constant step value and rounding effects. Human Resources Department Tel. 73566

  17. Shaft adjuster

    Science.gov (United States)

    Harry, Herbert H.

    1989-01-01

    Apparatus and method for the adjustment and alignment of shafts in high power devices. A plurality of adjacent rotatable angled cylinders are positioned between a base and the shaft to be aligned which when rotated introduce an axial offset. The apparatus is electrically conductive and constructed of a structurally rigid material. The angled cylinders allow the shaft such as the center conductor in a pulse line machine to be offset in any desired alignment position within the range of the apparatus.

  18. Adjustable collimator

    International Nuclear Information System (INIS)

    Carlson, R.W.; Covic, J.; Leininger, G.

    1981-01-01

    In a rotating fan beam tomographic scanner there is included an adjustable collimator and shutter assembly. The assembly includes a fan angle collimation cylinder having a plurality of different length slots through which the beam may pass for adjusting the fan angle of the beam. It also includes a beam thickness cylinder having a plurality of slots of different widths for adjusting the thickness of the beam. Further, some of the slots have filter materials mounted therein so that the operator may select from a plurality of filters. Also disclosed is a servo motor system which allows the operator to select the desired fan angle, beam thickness and filter from a remote location. An additional feature is a failsafe shutter assembly which includes a spring biased shutter cylinder mounted in the collimation cylinders. The servo motor control circuit checks several system conditions before the shutter is rendered openable. Further, the circuit cuts off the radiation if the shutter fails to open or close properly. A still further feature is a reference radiation intensity monitor which includes a tuning-fork shaped light conducting element having a scintillation crystal mounted on each tine. The monitor is placed adjacent the collimator between it and the source with the pair of crystals to either side of the fan beam

  19. Current status of the plutonium hot particle problem

    International Nuclear Information System (INIS)

    Richmond, C.R.

    1975-01-01

    Information now available on the question of lung irradiation from particulate plutonium is reviewed. Careful consideration of the available data shows that particulate plutonium is not more hazardous than the same amount of plutonium distributed uniformly. The data also suggest that the potential hazard from plutonium increases as the dispersion throughout the lung becomes more uniform

  20. Contamination of living environment and human organism with plutonium

    International Nuclear Information System (INIS)

    Benes, J.

    1981-01-01

    The applicability of 239 Pu in nuclear power is discussed. The radiotoxic properties of plutonium, its tissue distribution and the effects of internal and external contamination are described. The contamination of the atmosphere, water, and soil with plutonium isotopes is discussed. Dosimetry is described of plutonium in the living and working environments as is plutonium determination in the human organism. (H.S.)

  1. Plutonium use - Present status and prospects

    International Nuclear Information System (INIS)

    Dievoet, J. van; Fossoul, E.; Jonckheere, E.; Bemden, E. van den

    1977-01-01

    The use of plutonium in thermal and fast reactors is a demonstrated, if not proven, technology. Moreover, plutonium is being produced in increasing quantities. Evaluation of this production on a world scale shows that it would be theoretically possible to construct numerous breeders and thus to make the best use of plutonium, while considerably reducing uranium consumption. This source of plutonium is nevertheless dependent on the reprocessing of irradiated fuel. Long delays in installing and adequate world reprocessing capacity are weakening the prospects for introducing breeders. Furthermore, the critical situation regarding reprocessing may delay the development of complementary reprocessing methods for fuels with a high plutonium content and high burnup. The recycling of plutonium is now a well-known technique and any objections to it hardly bear analysis. Utilization of plutonium offers an appreciable saving in terms of uranium and separative work units; and it can also be shown that immediate reprocessing of the recycling fuel is not essential for the economics of the concept. Temporary storage of recycled fuel is a particularly safe form of concentrating plutonium, namely in irradiated plutonium-bearing fuel assemblies. Finally, recycling offers such flexibility that it represents no obstacle to fuel management at power plants with light-water reactors. These strategic considerations imply that the technology of using plutonium for fabricating thermal or fast reactor fuels is both technically reliable and economically viable. The methods used in industrial facilities are fully reassuring in this respect. Although various unsolved problems exist, none seems likely to impede current developments, while the industrial experience gained has enabled the economics and reliability of the methods to be improved appreciably. Apart from the techno-economic aspects, the plutonium industry must face extremely important problems in connection with the safety of personnel

  2. Plutonium focus area. Technology summary

    International Nuclear Information System (INIS)

    1997-09-01

    The Assistant Secretary for the Office of Environmental Management (EM) at the U.S. Department of Energy (DOE) chartered the Plutonium Focus Area (PFA) in October 1995. The PFA open-quotes...provides for peer and technical reviews of research and development in plutonium stabilization activities...close quotes In addition, the PFA identifies and develops relevant research and technology. The purpose of this document is to focus attention on the requirements used to develop research and technology for stabilization, storage, and preparation for disposition of nuclear materials. The PFA Technology Summary presents the approach the PFA uses to identify, recommend, and review research. It lists research requirements, research being conducted, and gaps where research is needed. It also summarizes research performed by the PFA in the traditional research summary format. This document encourages researchers and commercial enterprises to do business with PFA by submitting research proposals or open-quotes white papers.close quotes In addition, it suggests ways to increase the likelihood that PFA will recommend proposed research to the Nuclear Materials Stabilization Task Group (NMSTG) of DOE

  3. Automated amperometric plutonium assay system

    International Nuclear Information System (INIS)

    Burt, M.C.

    1985-01-01

    The amperometric titration for plutonium assay has been used in the nuclear industry for over twenty years and has been in routine use at the Hanford Engineering Development Laboratory since 1976 for the analysis of plutonium oxide and mixed oxide fuel material for the Fast Flux Test Facility. It has proven itself to be an accurate and reliable method. The method may be used as a direct end point titration or an excess of titrant may be added and a back titration performed to aid in determination of the end point. Due to the slowness of the PuVI-FeII reaction it is difficult to recognize when the end point is being approached and is very time consuming if the current is allowed to decay to the residual value after each titrant addition. For this reason the back titration in which the rapid FeII-CrVI reaction occurs is used by most laboratories. The back titration is performed by the addition of excess ferrous solution followed by two measured aliquots of standard dichromate with measurement of cell current after each addition

  4. Ceramification: A plutonium immobilization process

    Energy Technology Data Exchange (ETDEWEB)

    Rask, W.C. [Dept. of Energy, Golden, CO (United States); Phillips, A.G. [Rocky Flats Environmental Technology Site, Golden, CO (United States)

    1996-05-01

    This paper describes a low temperature technique for stabilizing and immobilizing actinide compounds using a combination process/storage vessel of stainless steel, in which measured amounts of actinide nitrate solutions and actinide oxides (and/or residues) are systematically treated to yield a solid article. The chemical ceramic process is based on a coating technology that produces rare earth oxide coatings for defense applications involving plutonium. The final product of this application is a solid, coherent actinide oxide with process-generated encapsulation that has long-term environmental stability. Actinide compounds can be stabilized as pure materials for ease of re-use or as intimate mixtures with additives such as rare earth oxides to increase their degree of proliferation resistance. Starting materials for the process can include nitrate solutions, powders, aggregates, sludges, incinerator ashes, and others. Agents such as cerium oxide or zirconium oxide may be added as powders or precursors to enhance the properties of the resulting solid product. Additives may be included to produce a final product suitable for use in nuclear fuel pellet production. The process is simple and reduces the time and expense for stabilizing plutonium compounds. It requires a very low equipment expenditure and can be readily implemented into existing gloveboxes. The process is easily conducted with less associated risk than proposed alternative technologies.

  5. Cancer hazard from inhaled plutonium

    International Nuclear Information System (INIS)

    Gofman, J.W.

    1975-01-01

    The best estimate of the lung cancer potential in humans for inhaled insoluble compounds of plutonium (such as PuO 2 particles) has been grossly underestimated by such authoritative bodies as the International Commission on Radiological Protection and the British Medical Research Council. Calculations are presented of lung cancer induction by 239 Pu as insoluble particles and for deposited reactor-grade Pu. The reason for the gross underestimate of the carcinogenic effects of Pu by ICRP or the British Medical Research Council (BMRC) is their use of a totally unrealistic idealized model for the clearance of deposited Pu from the lungs and bronchi plus their non-recognition of the bronchi as the true site for most human lung cancers. The erroneous model used by such organizations also fails totally to take into account the effect of cigarette-smoking upon the physiological function of human lungs. Plutonium nuclides, such as 239 Pu, or other alpha particle-emitting nuclides, in an insoluble form represent an inhalation cancer hazard in a class some 100,000 times more potent than the potent chemical carcinogens, weight for weight. The already-existing lung cancer data for beagle dogs inhaling insoluble PuO 2 particles is clearly in order of magnitude agreement with calculations for humans

  6. Japanese utilities' plutonium utilization program

    International Nuclear Information System (INIS)

    Matsuo, Yuichiro.

    1996-01-01

    Japan's 10 utility companies are working and will continue to work towards establishing a fully closed nuclear fuel cycle. The key goals of which are: (1) reprocessing spent fuel; (2) recycling recovered uranium and plutonium; and (3) commercializing fast breeder technology by around the year 2030. This course of action by the Japanese electric power industry is in full accordance with Japan's national policy outlined in the government's report ''The Long-Term Program for Research, Development, and Nuclear Energy,'' which was published in June 1994. The Japanese civilian nuclear program is a long-term program that looks into the 21st century and beyond. It is quite true that sustaining the recycling option for energy security and the global environment demands a large investment. For it to be accepted by the public, safety must be the highest priority and will be pursued at a great cost if necessary. In its history, Japan has learned that as technology advances, costs will come down. The Japanese utility industry will continue investment in technology without compromising safety until the recycling option becomes more competitive with other options. This effort will be equally applied to the development of the commercial FBRs. The Japanese utility industry is confident that Japan's stable policy and strong objective to develop competitive and peaceful technology will contribute to the global economy and the environment without increasing the threat of plutonium proliferation

  7. Mortality study of Los Alamos workers with higher exposures to plutonium

    International Nuclear Information System (INIS)

    Voelz, G.L.; Wilkinson, G.S.; Healy, J.W.; McInroy, J.F.; Tietjen, G.L.

    1983-01-01

    A group of white male workers with the highest internal depositions of plutonium at the Los Alamos National Laboratory was selected in 1974 for a study of mortality. This group of 224 persons includes all those with an estimated deposition (in 1974) of 10 nanocuries or more of plutonium, principally 239 Pu but also in some cases 238 Pu. Follow-up of these workers is 100% complete through 1980. Smoking histories were obtained on all persons. Exposure histories for external radiation and plutonium were reviewed for each subject. Standardized mortality ratios (SMR) were calculated using rates for white males in the United States population, adjusted for age and year of death. SMRs are low for all causes of death (56; 95% CI 40, 75) or for all malignant neoplasms (54; 95% CI 23,106). Cancers of interest for plutonium exposures, including cancers of bone, lung, liver, and bone marrow/lymphatic systems, were infrequent or absent. The absence of a detectable excess of cancer deaths is consistent with the low calculated risk to these workers using current radiation risk coefficients. An alternate theory that suggests much higher risk of lung cancer due to synergistic effects of smoking and inhaled insoluble plutonium particles is not supported by this study

  8. Valence photoelectron spectrum of KBr: Effects of electron correlation

    International Nuclear Information System (INIS)

    Calo, A.; Huttula, M.; Patanen, M.; Aksela, H.; Aksela, S.

    2008-01-01

    The valence photoelectron spectrum has been measured for molecular KBr. Experimental energies of the main and satellite structures have been compared with the results of ab initio calculations based on molecular orbital theory including configuration and multiconfiguration interaction approaches. Comparison between the experimental KBr spectrum and previously reported Kr valence photoelectron spectrum has also been performed in order to find out if electron correlation is of the same importance in the valence ionized state of KBr as in the corresponding state of Kr

  9. Laboratory-scale evaluations of alternative plutonium precipitation methods

    International Nuclear Information System (INIS)

    Martella, L.L.; Saba, M.T.; Campbell, G.K.

    1984-01-01

    Plutonium(III), (IV), and (VI) carbonate; plutonium(III) fluoride; plutonium(III) and (IV) oxalate; and plutonium(IV) and (VI) hydroxide precipitation methods were evaluated for conversion of plutonium nitrate anion-exchange eluate to a solid, and compared with the current plutonium peroxide precipitation method used at Rocky Flats. Plutonium(III) and (IV) oxalate, plutonium(III) fluoride, and plutonium(IV) hydroxide precipitations were the most effective of the alternative conversion methods tested because of the larger particle-size formation, faster filtration rates, and the low plutonium loss to the filtrate. These were found to be as efficient as, and in some cases more efficient than, the peroxide method. 18 references, 14 figures, 3 tables

  10. Temperature effects in the valence fluctuation of europium intermetallic compounds

    International Nuclear Information System (INIS)

    Menezes, O.L.T. de; Troper, A.; Gomes, A.A.

    1978-03-01

    A previously reported model for valence fluctuations in europium compound in order to account for thermal occupation effect. Experimental results are critically discussed and new experiments are suggested

  11. Positive valence music restores executive control over sustained attention.

    Science.gov (United States)

    Baldwin, Carryl L; Lewis, Bridget A

    2017-01-01

    Music sometimes improves performance in sustained attention tasks. But the type of music employed in previous investigations has varied considerably, which can account for equivocal results. Progress has been hampered by lack of a systematic database of music varying in key characteristics like tempo and valence. The aims of this study were to establish a database of popular music varying along the dimensions of tempo and valence and to examine the impact of music varying along these dimensions on restoring attentional resources following performance of a sustained attention to response task (SART) vigil. Sixty-nine participants rated popular musical selections that varied in valence and tempo to establish a database of four musical types: fast tempo positive valence, fast tempo negative valence, slow tempo positive valence, and slow tempo negative valence. A second group of 89 participants performed two blocks of the SART task interspersed with either no break or a rest break consisting of 1 of the 4 types of music or silence. Presenting positive valence music (particularly of slow tempo) during an intermission between two successive blocks of the SART significantly decreased miss rates relative to negative valence music or silence. Results support an attentional restoration theory of the impact of music on sustained attention, rather than arousal theory and demonstrate a means of restoring sustained attention. Further, the results establish the validity of a music database that will facilitate further investigations of the impact of music on performance.

  12. The distribution of plutonium-241 in rodents

    International Nuclear Information System (INIS)

    Priest, N.D.

    1977-01-01

    Plutonium-241 citrate solution at pH 6.5 was injected intravenously or intraperitoneally into hamsters and rats at a dose of 50 MBq kg -1 (1.35 mCi kg -1 ). The animals were killed 1 day or 1 week later, and tissues were removed for autoradiography and radiochemical analysis. Plutonium-241 was distributed in rats in the same way as plutonium-239, and is a suitable isotope for high-resolution tissue-section autoradiography. Plutonium deposits in cells consisted of a nuclear and a cytoplasmic component. In the hamster kidney cells, the amount associated with the nucleus was about 55 per cent of the total cellular plutonium at 24 hours after injection. Six days later, it was only about 30 per cent. Plutonium deposits were also characterized in hepatocytes, in the interstitial cells of the testes, in the cells of ovarian follicles, in chondrocytes and in bone cells, including osteoblasts and osteocytes. In bone there appeared to be both an extracellular and intracellular deposit. No evidence was found of substantial incorporation of plutonium into the mineral phase of bone. (author)

  13. Electrochemistry of plutonium in molten halides

    International Nuclear Information System (INIS)

    McCurry, L.E.; Moy, G.M.M.; Bowersox, D.F.

    1987-01-01

    The electrochemistry of plutonium in molten halides is of technological importance as a method of purification of plutonium. Previous authors have reported that plutonium can be purified by electrorefining impure plutonium in various molten haldies. Work to eluciate the mechanism of the plutonium reduction in molten halides has been limited to a chronopotentiometric study in LiCl-KCl. Potentiometric studies have been carried out to determine the standard reduction potential for the plutonium (III) couple in various molten alkali metal halides. Initial cyclic voltammetric experiments were performed in molten KCL at 1100 K. A silver/silver chloride (10 mole %) in equimolar NaCl-KCl was used as a reference electrode. Working and counter electrodes were tungsten. The cell components and melt were contained in a quartz crucible. Background cyclic voltammograms of the KCl melt at the tungsten electrode showed no evidence of electroactive impurities in the melt. Plutonium was added to the melt as PuCl/sub 3/, which was prepared by chlorination of the oxide. At low concentrations of PuCl/sub 3/ in the melt (0.01-0.03 molar), no reduction wave due to the reduction of Pu(III) was observed in the voltammograms up to the potassium reduction limit of the melt. However on scan reversal after scanning into the potassium reduction limit a new oxidation wave was observed

  14. Analytic determination of plutonium in the environment

    International Nuclear Information System (INIS)

    Ballada, J.

    1967-01-01

    The work described in this report was undertaken with a view to determining the plutonium content in the fall-out from nuclear explosions. In the first part are described in turn the importance of the problems due to the plutonium, the physico-chemical properties of the radioelement and the biological dangers which it presents. A detailed and critical analysis is made of the radio-toxicological determination of the plutonium as reported in the literature prior to this report. The second part consists in the presentation of a judicious choice of techniques making it possible to determine plutonium in air, rain-water, soils and ash. After a detailed description of the measurement equipment and the operational techniques which have been developed, a justification of these techniques is given with particular reference to their sensitivity and specificity. After a brief conclusion concerning the preceding chapters, the results are presented. These are then discussed in the ease of each element in which the plutonium has been determined. This discussion is concluded by a consideration of the importance of the occurrence of fall-out plutonium on problems relating to public health. From a consideration of 200 analyses carried out, it is concluded that the contribution of plutonium to the exposure of populations is still very small compared to that of natural radiation and that due to such fission products as strontium 90. The report includes 63 literature references, 26 figures and 11 tables. (author) [fr

  15. Solubility of plutonium dioxide aerosols, in vitro

    International Nuclear Information System (INIS)

    Newton, G.J.; Kanapilly, G.M.

    1976-01-01

    Solubility of plutonium aerosols is an important parameter in establishing risk estimates for industrial workers who might accidentally inhale these materials and in evaluating environmental health impacts associated with Pu. In vitro solubility of industrial plutonium aerosols in a simulated lung fluid is compared to similar studies with ultrafine aerosols from laser ignition of delta phase plutonium metal and laboratory-produced spherical particles of 238 PuO 2 and 239 PuO 2 . Although relatively insoluble, industrial plutonium-mixed oxide aerosols were much more soluble than laboratory-produced plutonium dioxide particles. Chain agglomerate aerosols from laser ignition of metallic Pu indicated in vitro dissolution half-times of 10 and 50 days for activity median aerodynamic diameter (AMAD) of 0.7 and 2.3 μm, respectively. Plutonium-containing mixed oxide aerosols indicated dissolution half-times of 40 to 500 days for particles formed by industrial powder comminution and blending. Centerless grinding of fuel pellets yielded plutonium-containing aerosols with dissolution half-times of 1200 to 8000 days. All mixed oxide particles were in the size range 1.0 μm to 2.5 μm AMAD

  16. PRISM reactor. An option for plutonium disposition?

    Energy Technology Data Exchange (ETDEWEB)

    Fehlinger, Sebastian; Friess, Friederike; Kuett, Moritz [IANUS, Technische Universitaet Darmstadt (Germany)

    2015-07-01

    The Power Reactor Innovative Small Module (PRISM) is sodium cooled fast reactor model. The energy output depends on the core configuration, however with an energy output of approximately 300 MWe, the PRISM reactor belongs to the class of small modular reactors. Beside using the reactor as a breeder reactor or for the transmutation of nuclear waste, it might also be used as a burner reactor for separated plutonium. This includes for example U.S.-American excess weapon-grade plutonium as well as separated reactor-grade plutonium. Recently, there has been an ongoing discussion in GB to use the PRISM reactor to dispose their excess civilian plutonium. Depending on the task, the core configuration varies slightly. We will present different layouts and the matching MCNP models, these models can then be used to conduct depletion calculations. From these results, analysis of the change in the plutonium isotopics in the spent fuel, the amount of fissioned plutonium, and the possible annual plutonium throughputs is possible.

  17. The Plutonium Temperature Effect Experimental Program

    Energy Technology Data Exchange (ETDEWEB)

    Haeck, Wim; Leclaire, Nicolas; Letang, Eric [IRSN, Fontenay-aux-Roses (France); Girault, Emmanuel; Fouillaud, Patrick [CEA, VALDUC (France)

    2008-07-01

    Various theoretical studies have shown that highly diluted plutonium solutions could have a positive temperature effect but (up to now) no experimental program has confirmed this effect. The main goal of the French Plutonium Temperature Effect Experimental Program (or PU+ in short) is to effectively show that such a positive temperature effect exists for diluted plutonium solutions. The experiments were conducted in the 'Apparatus B' facility at the CEA Valduc research centre in France and involved several sub-critical approach type of experiments using plutonium nitrate solutions with concentrations of 14.3, 15 and 20 g/l at temperatures ranging from 20 to 40 deg. C. A total number of 14 phase I experiments (consisting of independent subcritical approaches) have been performed (5 at 20 g/l, 4 at 15 g/l and 5 at 14.3 g/l) between 2006 and 2007. The impact of the uncertainties on the solution acidity and the plutonium concentration makes it difficult to clearly demonstrate the positive temperature effect, requiring an additional phase II experiment (in which the use of the same plutonium solution was ensured) from 22 to 28 deg. C performed in July 2007. This experiment has shown the existence of a positive temperature effect approx +2 pcm/deg. C (from 22 to 28 deg. C for a plutonium concentration of 14.3 g/l). (authors)

  18. Plutonium speciation affected by environmental bacteria

    International Nuclear Information System (INIS)

    Neu, M.P.; Icopini, G.A.; Boukhalfa, H.

    2005-01-01

    Plutonium has no known biological utility, yet it has the potential to interact with bacterial cellular and extracellular structures that contain metal-binding groups, to interfere with the uptake and utilization of essential elements, and to alter cell metabolism. These interactions can transform plutonium from its most common forms, solid, mineral-adsorbed, or colloidal Pu(IV), to a variety of biogeochemical species that have much different physico-chemical properties. Organic acids that are extruded products of cell metabolism can solubilize plutonium and then enhance its environmental mobility, or in some cases facilitate plutonium transfer into cells. Phosphate- and carboxylate-rich polymers associated with cell walls can bind plutonium to form mobile biocolloids or Pu-laden biofilm/mineral solids. Bacterial membranes, proteins or redox agents can produce strongly reducing electrochemical zones and generate molecular Pu(III/IV) species or oxide particles. Alternatively, they can oxidize plutonium to form soluble Pu(V) or Pu(VI) complexes. This paper reviews research on plutonium-bacteria interactions and closely related studies on the biotransformation of uranium and other metals. (orig.)

  19. Plutonium peroxide precipitation: review and current research

    International Nuclear Information System (INIS)

    Hagan, P.G.; Miner, F.J.

    1980-01-01

    Increasing the HNO 3 concentration decreases the filtration time but increases the plutonium concentration in the filtrate. A compromise was therefore necessary. If a minimum plutonium concentration is required in the filtrate, the acidity could be lowered to 1.9M with an approximate doubling in the filtration time. The H 2 O 2 concentration has little effect on filtration time. However, the higher the H 2 O 2 concentration, the less plutonium lost to the filtrate. Concentrations higher than the 22 moles/mole Pu recommended (at least up to 30 molar which was the highest investigated) would be beneficial if reagent costs are not excessive and production capacity exists for destroying the excess H 2 O 2 in the filtrate. Although the effect is not large, filtration time is shorter and the plutonium concentration in the filtrate is lower if metallic impurities are present. The slowest rate of H 2 O 2 addition investigated gives a plutonium peroxide precipitate with the fastest filtration time. The rate of addition has very little effect on the plutonium concentration in the filtrate. The temperature has little effect on the filtration time. 14 0 C is recommended since decomposition of H 2 O 2 would be slower at 14 0 C than at 22 0 C (min. Pu content in the filtrate). The effect of digestion time on both the filtration time and the plutonium content in the filtrate is minor, so the shortest digestion time investigated is recommended

  20. Radiological safety aspects of handling plutonium

    International Nuclear Information System (INIS)

    Sundararajan, A.R.

    2016-01-01

    Department of Atomic Energy in its scheme of harnessing the nuclear energy for electrical power generation and strategic applications has given a huge role to utilization of plutonium. In the power production programme, fast reactors with plutonium as fuel are expected to play a major role. This would require establishing fuel reprocessing plants to handle both thermal and fast reactor fuels. So in the nuclear fuel cycle facilities variety of chemical, metallurgical, mechanical operations have to be carried out involving significant inventories of "2"3"9 Pu and associated radionuclides. Plutonium is the most radiotoxic radionuclide and therefore any facility handling it has to be designed and operated with utmost care. Two problems of major concern in the protection of persons working in plutonium handling facilities are the internal exposure to the operating personnel from uptake of plutonium and transplutonic nuclides as they are highly radiotoxic and the radiation exposure of hands and eye lens during fuel fabrication operations especially while handling recycled high burn up plutonium. In view of the fact that annual limit for intake is very small for "2"3"9Pu and its radiation emission characteristics are such that it is a huge challenge for the health physicists to detect Pu in air and in workers. This paper discusses the principles and practices followed in providing radiological surveillance to workers in plutonium handling areas. The challenges in protecting the workers from receiving exposures to hands and eye lens in handling high burn up plutonium are also discussed. The sites having Pu fuel cycle facilities should have trained medical staff to handle cases involving excessive intake of plutonium. (author)

  1. Assesment of Plutonium 238 and Plutonium 239+240 in soils of different agricultural regions of Guatemala

    International Nuclear Information System (INIS)

    Gutierrez Martinez, E.A.

    1998-02-01

    In this report an assesment and measurement of PLUTONIUM 238, PLUTONIUM 239, and PLUTONIUM 240 are made. Samples of cultivated soils in 15 provinces of Guatemala were taken. To separate plutonium isotopes a radiochemical method was made using extraction, precipitation and ionic interchange. By electrodeposition the plutonium was measured using an alpha spectroscopy by PIPS method. The radioactivity ranges from 2.84 mBq/Kg to 36.38 mBq/Kg for plutonium 238, and 8.46 mBq/Kg to 26.61 mBq/Kg for plutonium 239+240

  2. Lung cancers already produced by plutonium inhalation

    International Nuclear Information System (INIS)

    Anon.

    1981-01-01

    This chapter presents the basis for the author's estimate that plutonium particulates have already committed approximately 950,000 persons worldwide to a lung-cancer death, and that more will be so committed in the future, even if no more plutonium is dispersed in the environment. The author's calculations are based on fallout data from atmospheric bomb testing, and on two sets of workers exposed to plutonium: one group at the Rocky Flats Plant in Colorado, and the other at the Los Alamos Laboratory who were involved in the Manhattan Project

  3. HENC performance evaluation and plutonium calibration

    International Nuclear Information System (INIS)

    Menlove, H.O.; Baca, J.; Pecos, J.M.; Davidson, D.R.; McElroy, R.D.; Brochu, D.B.

    1997-10-01

    The authors have designed a high-efficiency neutron counter (HENC) to increase the plutonium content in 200-L waste drums. The counter uses totals neutron counting, coincidence counting, and multiplicity counting to determine the plutonium mass. The HENC was developed as part of a Cooperative Research and Development Agreement between the Department of Energy and Canberra Industries. This report presents the results of the detector modifications, the performance tests, the add-a-source calibration, and the plutonium calibration at Los Alamos National Laboratory (TA-35) in 1996

  4. Pyrochemical recovery of plutonium fluoride reduction slag

    International Nuclear Information System (INIS)

    Christensen, D.C.; Rayburn, J.A.

    1983-07-01

    A process was developed for the pyrochemical recovery of plutonium from residues resulting from the PuF 4 reduction process. The process involves crushing the CaF 2 slag and dissolving it at 800 0 C in a CaCl 2 solvent. The plutonium, which exists either as finely divided metal or as incompletely reduced fluoride salt, is reduced to metal and/or allowed to coalesce as a massive button in the bottom of the reaction crucible. The recovery of plutonium in a 1-day cycle averaged 96%; all of the resulting residues were discardable

  5. Heavy water critical experiments on plutonium lattice

    International Nuclear Information System (INIS)

    Miyawaki, Yoshio; Shiba, Kiminori

    1975-06-01

    This report is the summary of physics study on plutonium lattice made in Heavy Water Critical Experiment Section of PNC. By using Deuterium Critical Assembly, physics study on plutonium lattice has been carried out since 1972. Experiments on following items were performed in a core having 22.5 cm square lattice pitch. (1) Material buckling (2) Lattice parameters (3) Local power distribution factor (4) Gross flux distribution in two region core (5) Control rod worth. Experimental results were compared with theoretical ones calculated by METHUSELAH II code. It is concluded from this study that calculation by METHUSELAH II code has acceptable accuracy in the prediction on plutonium lattice. (author)

  6. Nondestructive analysis of plutonium contaminated soil

    International Nuclear Information System (INIS)

    Smith, H.E.; Taylor, L.H.

    1977-01-01

    Plutonium contaminated soil is currently being removed from a covered liquid waste disposal trench near the Pu Processing facility on the Hanford Project. This soil with the plutonium is being mined using remote techniques and equipment. The mined soil is being packaged for placement into retrievable storage, pending possible recovery. To meet the requirements of criticality safety and materials accountability, a nondestructive analysis program has been developed to determine the quantity of plutonium in each packing-storage container. This paper describes the total measurement program: equipment systems, calibration techniques, matrix assumption, instrument control program and a review of laboratory operating experience

  7. Plutonium Immobilization Can Loading Conceptual Design

    International Nuclear Information System (INIS)

    Kriikku, E.

    1999-01-01

    'The Plutonium Immobilization Facility will encapsulate plutonium in ceramic pucks and seal the pucks inside welded cans. Remote equipment will place these cans in magazines and the magazines in a Defense Waste Processing Facility (DWPF) canister. The DWPF will fill the canister with glass for permanent storage. This report discusses the Plutonium Immobilization can loading conceptual design and includes a process block diagram, process description, preliminary equipment specifications, and several can loading issues. This report identifies loading pucks into cans and backfilling cans with helium as the top priority can loading development areas.'

  8. Fluorescent determination of neptunium in plutonium

    International Nuclear Information System (INIS)

    Alexandruk, V.M.; Babaev, A.S.; Dem'yanova, T.A.; Stepanov, A.V.

    1991-01-01

    This paper describes a new procedure for direct determination of Neptunium in Plutonium using laser induced time resolved fluorescence method. The procedure based on measurement of fluorescence intensity of Neptunium followed its concentration in effective layer of pellet of calcium fluoride. Detection limit of determination of Neptunium is 2 10 -12 g. At the level of Neptunium content in Plutonium more than 5 ppm relative standard deviation is equal 0.08-0.12. For carrying out of single measurement it is necessary neither more nor less 5 mkg Plutonium

  9. Excess Weapons Plutonium Immobilization in Russia

    International Nuclear Information System (INIS)

    Jardine, L.; Borisov, G.B.

    2000-01-01

    The joint goal of the Russian work is to establish a full-scale plutonium immobilization facility at a Russian industrial site by 2005. To achieve this requires that the necessary engineering and technical basis be developed in these Russian projects and the needed Russian approvals be obtained to conduct industrial-scale immobilization of plutonium-containing materials at a Russian industrial site by the 2005 date. This meeting and future work will provide the basis for joint decisions. Supporting R and D projects are being carried out at Russian Institutes that directly support the technical needs of Russian industrial sites to immobilize plutonium-containing materials. Special R and D on plutonium materials is also being carried out to support excess weapons disposition in Russia and the US, including nonproliferation studies of plutonium recovery from immobilization forms and accelerated radiation damage studies of the US-specified plutonium ceramic for immobilizing plutonium. This intriguing and extraordinary cooperation on certain aspects of the weapons plutonium problem is now progressing well and much work with plutonium has been completed in the past two years. Because much excellent and unique scientific and engineering technical work has now been completed in Russia in many aspects of plutonium immobilization, this meeting in St. Petersburg was both timely and necessary to summarize, review, and discuss these efforts among those who performed the actual work. The results of this meeting will help the US and Russia jointly define the future direction of the Russian plutonium immobilization program, and make it an even stronger and more integrated Russian program. The two objectives for the meeting were to: (1) Bring together the Russian organizations, experts, and managers performing the work into one place for four days to review and discuss their work with each other; and (2) Publish a meeting summary and a proceedings to compile reports of all the

  10. Plutonium Immobilization Can Loading Conceptual Design

    Energy Technology Data Exchange (ETDEWEB)

    Kriikku, E.

    1999-05-13

    'The Plutonium Immobilization Facility will encapsulate plutonium in ceramic pucks and seal the pucks inside welded cans. Remote equipment will place these cans in magazines and the magazines in a Defense Waste Processing Facility (DWPF) canister. The DWPF will fill the canister with glass for permanent storage. This report discusses the Plutonium Immobilization can loading conceptual design and includes a process block diagram, process description, preliminary equipment specifications, and several can loading issues. This report identifies loading pucks into cans and backfilling cans with helium as the top priority can loading development areas.'

  11. Uranium-plutonium fuel for fast reactors

    International Nuclear Information System (INIS)

    Antipov, S.A.; Astafiev, V.A.; Clouchenkov, A.E.; Gustchin, K.I.; Menshikova, T.S.

    1996-01-01

    Technology was established for fabrication of MOX fuel pellets from co-precipitated and mechanically blended mixed oxides. Both processes ensure the homogeneous structure of pellets readily dissolvable in nitric acid upon reprocessing. In order to increase the plutonium charge in a reactor-burner a process was tested for producing MOX fuel with higher content of plutonium and an inert diluent. It was shown that it is feasible to produce fuel having homogeneous structure and the content of plutonium up to 45% mass

  12. Method of stripping plutonium from tributyl phosphate solution which contains dibutyl phosphate-plutonium stable complexes

    International Nuclear Information System (INIS)

    Ochsenfeld, W.; Schmieder, H.

    1976-01-01

    Fast breeder fuel elements which have been highly burnt-up are reprocessed by extracting uranium and plutonium into an organic solution containing tributyl phosphate. The tributyl phosphate degenerates at least partially into dibutyl phosphate and monobutyl phosphate, which form stable complexes with tetravalent plutonium in the organic solution. This tetravalent plutonium is released from its complexed state and stripped into aqueous phase by contacting the organic solution with an aqueous phase containing tetravalent uranium. 6 claims, 1 drawing figure

  13. Plutonium

    International Nuclear Information System (INIS)

    1981-09-01

    The subject is discussed under the headings: creation (fuel cycle, Pu formed in thermal reactors); properties; Pu in fast reactors; fast reactor experience; radioactivity; handling; Pu and weapons. (U.K.)

  14. Comparisons of plutonium, thorium, and cerium tellurite sulfates.

    Science.gov (United States)

    Lin, Jian; Cross, Justin N; Diwu, Juan; Meredith, Nathan A; Albrecht-Schmitt, Thomas E

    2013-04-15

    The hydrothermal reaction of PuCl3 or CeCl3 with TeO2 in the presence of sulfuric acid under the comparable conditions results in the crystallization of Pu(TeO3)(SO4) or Ce2(Te2O5)(SO4)2, respectively. Pu(TeO3)(SO4) and its isotypic compound Th(TeO3)(SO4) are characterized by a neutral layer structure with no interlamellar charge-balancing ions. However, Ce2(Te2O5)(SO4)2 possesses a completely different dense three-dimensional framework. Bond valence calculation and UV-vis-NIR spectra indicate that the Ce compound is trivalent whereas the Pu and Th compounds are tetravalent leading to the formation of significantly different compounds. Pu(TeO3)(SO4), Th(TeO3)(SO4), and Ce2(Te2O5)(SO4)2 represent the first plutonium/thorium/cerium tellurite sulfate compounds. Our study strongly suggests that the chemistries of Pu and Ce are not the same, and this is another example of the failure of Ce as a surrogate.

  15. Seniority Number in Valence Bond Theory.

    Science.gov (United States)

    Chen, Zhenhua; Zhou, Chen; Wu, Wei

    2015-09-08

    In this work, a hierarchy of valence bond (VB) methods based on the concept of seniority number, defined as the number of singly occupied orbitals in a determinant or an orbital configuration, is proposed and applied to the studies of the potential energy curves (PECs) of H8, N2, and C2 molecules. It is found that the seniority-based VB expansion converges more rapidly toward the full configuration interaction (FCI) or complete active space self-consistent field (CASSCF) limit and produces more accurate PECs with smaller nonparallelity errors than its molecular orbital (MO) theory-based analogue. Test results reveal that the nonorthogonal orbital-based VB theory provides a reverse but more efficient way to truncate the complete active Hilbert space by seniority numbers.

  16. What is plutonium stabilization, and what is safe storage of plutonium?

    International Nuclear Information System (INIS)

    Forsberg, C.W.

    1995-01-01

    The end of the cold war has resulted in the shutdown of nuclear weapons production and the start of dismantlement of significant numbers of nuclear weapons. This, in turn, is creating an inventory of plutonium requiring interim and long-term storage. A key question is, ''What is required for safe, multidecade, plutonium storage?'' The requirements for storage, in turn, define what is needed to stabilize the plutonium from its current condition into a form acceptable for interim and long-term storage. Storage requirements determine if research is required to (1) define required technical conditions for interim and long-term storage and (2) develop or improve current stabilization technologies. Storage requirements depend upon technical, policy, and economic factors. The technical issues are complicated by several factors. Plutonium in aerosol form is highly hazardous. Plutonium in water is hazardous. The plutonium inventory is in multiple chemical forms--some of which are chemically reactive. Also, some of the existing storage forms are clearly unsuitable for storage periods over a few years. Gas generation by plutonium compounds complicates storage: (1) all plutonium slowly decays creating gaseous helium and (2) the radiation from plutonium decay can initiate many chemical reactions-some of which generate significant quantities of gases. Gas generation can pressurize sealed storage packages. Last nuclear criticality must be avoided

  17. Animal data on plutonium toxicity

    International Nuclear Information System (INIS)

    Thompson, R.C.

    1975-01-01

    Animal data are necessary in the assessment of plutonium toxicity since it is unlikely that the necessary information on effects from humans will be obtained. Experiments on animals must be designed to provide understanding of the mechanisms at work if the results are to be applied to man since it is a statistical impossibility to design experiments to measure directly the low levels of risk that are of concern. Cancer induction appears to be the risk of greatest concern with the lung and bone apparently the most susceptible organs, depending upon the method of administration. Current limitations on these organs do not appear to have the safety margin formerly believed and there are some uncertainties in the extrapolation from animal data to man. (author)

  18. Deep borehole disposal of plutonium

    International Nuclear Information System (INIS)

    Gibb, F. G. F.; Taylor, K. J.; Burakov, B. E.

    2008-01-01

    Excess plutonium not destined for burning as MOX or in Generation IV reactors is both a long-term waste management problem and a security threat. Immobilisation in mineral and ceramic-based waste forms for interim safe storage and eventual disposal is a widely proposed first step. The safest and most secure form of geological disposal for Pu yet suggested is in very deep boreholes and we propose here that the key to successful combination of these immobilisation and disposal concepts is the encapsulation of the waste form in small cylinders of recrystallized granite. The underlying science is discussed and the results of high pressure and temperature experiments on zircon, depleted UO 2 and Ce-doped cubic zirconia enclosed in granitic melts are presented. The outcomes of these experiments demonstrate the viability of the proposed solution and that Pu could be successfully isolated from its environment for many millions of years. (authors)

  19. Design criteria for plutonium gloveboxes

    International Nuclear Information System (INIS)

    Anon.

    1981-01-01

    The standard defines criteria for the design of glovebox systems to be used for the handling of plutonium in any form or isotopic composition or when mixed with other elements or compounds. The glovebox system is a series of physical barriers provided with glove ports and gloves, through which process and maintenance operations may be performed, together with an operating ventilation system. The system minimizes the potential for release of radioactive material to the environment, protects operators from contamination, and mitigates the consequences of abnormal condiations. The standard covers confinement, construction, materials, windows, glove ports, gloves, equipment insertion and removal, lighting, ventilation, fire protection, criticality prevention, services and utilities, radiation shielding, waste systems, monitoring and alarm systems, safeguards, quality assurance, and decommissioning

  20. Plutonium focus area: Technology summary

    International Nuclear Information System (INIS)

    1996-03-01

    To ensure research and development programs focus on the most pressing environmental restoration and waste management problems at the U.S. Department of Energy (DOE), the Assistant Secretary for the Office of Environmental Management (EM) established a working group in August 1993 to implement a new approach to research and technology development. As part of this approach, EM developed a management structure and principles that led to creation of specific focus areas. These organizations were designed to focus scientific and technical talent throughout DOE and the national scientific community on major environmental restoration and waste management problems facing DOE. The focus area approach provides the framework for inter-site cooperation and leveraging of resources on common problems. After the original establishment of five major focus areas within the Office of Technology Development (EM-50), the Nuclear Materials Stabilization Task Group (NMSTG, EM-66) followed EM-50's structure and chartered the Plutonium Focus Area (PFA). NMSTG's charter to the PFA, described in detail later in this book, plays a major role in meeting the EM-66 commitments to the Defense Nuclear Facilities Safety Board (DNFSB). The PFA is a new program for FY96 and as such, the primary focus of revision 0 of this Technology Summary is an introduction to the Focus Area; its history, development, and management structure, including summaries of selected technologies being developed. Revision 1 to the Plutonium Focus Area Technology Summary is slated to include details on all technologies being developed, and is currently planned for release in August 1996. The following report outlines the scope and mission of the Office of Environmental Management, EM-60, and EM-66 organizations as related to the PFA organizational structure

  1. Probing Transient Valence Orbital Changes with Picosecond Valence-to-Core X-ray Emission Spectroscopy

    DEFF Research Database (Denmark)

    March, Anne Marie; Assefa, Tadesse A.; Boemer, Christina

    2017-01-01

    We probe the dynamics of valence electrons in photoexcited [Fe(terpy)2]2+ in solution to gain deeper insight into the Fe ligand bond changes. We use hard X-ray emission spectroscopy (XES), which combines element specificity and high penetration with sensitivity to orbital structure, making...... valence orbitals to the nascent core-hole. Vtc-XES offers particular insight into the molecular orbitals directly involved in the light-driven dynamics; a change in the metal ligand orbital overlap results in an intensity reduction and a blue energy shift in agreement with our theoretical calculations...... and more subtle features at the highest energies reflect changes in the frontier orbital populations....

  2. Prediction of valence and arousal from music features

    NARCIS (Netherlands)

    Den Brinker, A.C.; Van Dinther, C.H.B.A.; Skowronek, J.

    2011-01-01

    Mood is an important attribute of music and knowledge on mood can beused as a basic ingredient in music recommender and retrieval systems. Moods are assumed to be dominantly determined by two dimensions:valence and arousal. An experiment was conducted to attain data forsong-based ratings of valence

  3. Semiempirical search for oxide superconductors based on bond valence sums

    International Nuclear Information System (INIS)

    Tanaka, S.; Fukushima, N.; Niu, H.; Ando, K.

    1992-01-01

    Relationships between crystal structures and electronic states of layered transition-metal oxides are analyzed in the light of bond valence sums. Correlations between the superconducting transition temperature T c and the bond-valence-sum parameters are investigated for the high-T c cuprate compounds. Possibility of making nonsuperconducting oxides superconducting is discussed. (orig.)

  4. Investigating Valence and Autonomy in Children's Relationships with Imaginary Companions

    Science.gov (United States)

    McInnis, Melissa A.; Pierucci, Jillian M.; Gilpin, Ansley Tullos

    2013-01-01

    Little research has explored valence and autonomy in children's imaginary relationships. In the present study, a new interview (modeled after an existing measure for real relationships) was designed to elicit descriptions of both positive and negative interactions with imaginary companions and to provide a measure of relationship valence and…

  5. Plutonium finishing plant dangerous waste training plan

    International Nuclear Information System (INIS)

    ENTROP, G.E.

    1999-01-01

    This training plan describes general requirements, worker categories, and provides course descriptions for operation of the Plutonium Finish Plant (PFP) waste generation facilities, permitted treatment, storage and disposal (TSD) units, and the 90-Day Accumulation Areas

  6. Recommendations for plutonium colloid size determination

    International Nuclear Information System (INIS)

    Kosiewicz, S.T.

    1984-02-01

    This report presents recommendations for plutonium colloid size determination and summarizes a literature review, discussions with other researchers, and comments from equipment manufacturers. Four techniques suitable for plutonium colloid size characterization are filtration and ultrafiltration, gel permeation chromatography, diffusion methods, and high-pressure liquid chromatography (conditionally). Our findings include the following: (1) Filtration and ultrafiltration should be the first methods used for plutonium colloid size determination because they can provide the most rapid results with the least complicated experimental arrangement. (2) After expertise has been obtained with filtering, gel permeation chromatography should be incorporated into the colloid size determination program. (3) Diffusion methods can be used next. (4) High-pressure liquid chromatography will be suitable after appropriate columns are available. A plutonium colloid size characterization program with filtration/ultrafiltration and gel permeation chromatography has been initiated

  7. IMPROVED PROCESS OF PLUTONIUM CARRIER PRECIPITATION

    Science.gov (United States)

    Faris, B.F.

    1959-06-30

    This patent relates to an improvement in the bismuth phosphate process for separating and recovering plutonium from neutron irradiated uranium, resulting in improved decontamination even without the use of scavenging precipitates in the by-product precipitation step and subsequently more complete recovery of the plutonium in the product precipitation step. This improvement is achieved by addition of fluomolybdic acid, or a water soluble fluomolybdate, such as the ammonium, sodium, or potassium salt thereof, to the aqueous nitric acid solution containing tetravalent plutonium ions and contaminating fission products, so as to establish a fluomolybdate ion concentration of about 0.05 M. The solution is then treated to form the bismuth phosphate plutonium carrying precipitate.

  8. Calculating the plutonium in spent fuel elements

    International Nuclear Information System (INIS)

    Barnham, Keith

    1992-01-01

    Many members of the public are concerned about plutonium. They are worried about its environmental, health and proliferation risks. Fundamental to all such considerations are two related questions: how much plutonium do nuclear reactors produce ? and how accurately do the relevant authorities know these production figures ? These two questions have been studied with particular reference to the UK civil Magnox reactors. In 1990 these were still the only UK civil reactors whose spent fuel had been reprocessed to extract plutonium in routine production. It has not been possible to conclude that the relevant government industry and safeguard authorities are aware of how much plutonium these reactors produce and that the figures are known to the highest achievable accuracy. To understand why, this chapter will outline some of the history of the attempts to get answers to these two questions. (author)

  9. Pulmonary carcinogenesis from plutonium-containing particles

    International Nuclear Information System (INIS)

    Thomas, R.G.; Smith, D.M.; Anderson, E.C.

    1980-01-01

    Plutonium administered as an alpha radiation source to the respiratory tracts of Syrian hamsters has resulted in various incidences of neoplasia. Adenomas are the primary lung tumor observed, but adenocarcinomas are also prevalent

  10. Direct reduction of plutonium from dicesium hexachloroplutonate

    International Nuclear Information System (INIS)

    Averill, W.A.; Boyd, T.E.

    1991-01-01

    The Rocky Flats Plant produces dicesium hexachloroplutonate (DCHP) primarily as a reagent in the molten salt extraction of americium from plutonium metal. DCHP is precipitated from aqueous chloride solutions derived from the leaching of process residues with a high degree of selectivity. DCHP is a chloride salt of plutonium, while the traditional aqueous precipitate is a hydrated oxide. Plutonium metal preparation from the oxide involves either the conversion of oxide to a halide followed by metallothermic reduction or direct reduction of the oxide using a flux. Either method generates at least three times as much radioactively contaminated waste as metal produced. Plutonium concentration by DCHP precipitation, however, produces a chloride salt that can be reduced using calcium metal at a temperature of approximately 1000K. In this paper the advantages and limitations of this process are discussed

  11. SEPARATION OF URANIUM, PLUTONIUM, AND FISSION PRODUCTS

    Science.gov (United States)

    Spence, R.; Lister, M.W.

    1958-12-16

    Uranium and plutonium can be separated from neutron-lrradiated uranium by a process consisting of dissolvlng the lrradiated material in nitric acid, saturating the solution with a nitrate salt such as ammonium nitrate, rendering the solution substantially neutral with a base such as ammonia, adding a reducing agent such as hydroxylamine to change plutonium to the trivalent state, treating the solution with a substantially water immiscible organic solvent such as dibutoxy diethylether to selectively extract the uranium, maklng the residual aqueous solutlon acid with nitric acid, adding an oxidizing agent such as ammonlum bromate to oxidize the plutonium to the hexavalent state, and selectlvely extracting the plutonium by means of an immlscible solvent, such as dibutoxy dlethyletber.

  12. Plutonium Immobilization Bagless Transfer Can Size Evaluation

    International Nuclear Information System (INIS)

    Kriikku, E.; Stokes, M.; Rogers, L.; Ward, C.

    1998-02-01

    This report identifies and documents the most appropriate bagless transfer can size to support Plutonium Immobilization Can Loading operations. Also, this report considers can diameter, can wall thickness, and can length

  13. The first metallurgical tests on plutonium

    International Nuclear Information System (INIS)

    Grison, E.; Abramson, R.; Anselin, F.; Monti, H.

    1958-01-01

    Metallic plutonium was first prepared in France in January 1956, as soon as we had access to quantities of the order of several grams of plutonium, which had been extracted from the rods of the pile EL2 at Saclay. Since up to the present this reactor, of thermal power 2 000 kW, has been our only source of plutonium, we have so far only worked on experimental quantities sufficient for the basic tests but not for tests on a scale of possible applications. It is this work, carried out during this phase of preliminary research, which is described below. With the starting up of the plutonium extraction plant at Marcoule, where the reactor G1 has been operating at power for more than a year, we shall go on next to a another order of magnitude which will allow the manufacture and experimentation of prototype fuel elements. (author) [fr

  14. Study of plutonium cycle in marine ecosystems

    International Nuclear Information System (INIS)

    Merino Pareja, J.; Sanchez Cabeza, J. A.; Molero Savall, J.; Masque Barri, P.

    1998-01-01

    The distribution, transport and accumulation mechanisms of transuranics (and other radionuclides) in the marine environment depend on the source term, biogeochemical cycles, transport with the water masses, sedimentation processes and transfer mechanisms in the trophic chain. The biogeochemical behaviour of plutonium, which has been the focus of our work, was studied using the following approaches: determination of the physico-chemical speciation of plutonium in marine waters, vertical flux in the water column, uptake by marine organisms (phytoplankton and zooplankton) and distribution in dements cores. A preliminary model of the accumulation and distribution of plutonium in the first levels of the marine food chain in the Irish Sea has also been formulated. All this information allowed us to obtain an integrated view of the behaviour of plutonium in the marine environment. (Author) 14 refs

  15. Plutonium Chemistry in the UREX Separation Processes

    International Nuclear Information System (INIS)

    Paulenova, Alena; Vandegrift, George F. III; Czerwinski, Kenneth R.

    2009-01-01

    The objective of the project is to examine the chemical speciation of plutonium in UREX+ (uranium/tributylphosphate) extraction processes for advanced fuel technology. Researchers will analyze the change in speciation using existing thermodynamics and kinetic computer codes to examine the speciation of plutonium in aqueous and organic phases. They will examine the different oxidation states of plutonium to find the relative distribution between the aqueous and organic phases under various conditions such as different concentrations of nitric acid, total nitrates, or actinide ions. They will also utilize techniques such as X-ray absorbance spectroscopy and small-angle neutron scattering for determining plutonium and uranium speciation in all separation stages. The project started in April 2005 and is scheduled for completion in March 2008.

  16. International shipment of plutonium by air

    International Nuclear Information System (INIS)

    Mercado, J.E.; McGrogan, J.P.

    1995-05-01

    In support of the United States (US) Government's decision to place excess plutonium oxide at the US Department of Energy's (DOE) Hanford Site under International Atomic Energy Agency (IAEA) safeguards, the Department of State notified the Congress that a plutonium storage vault at the Plutonium Finishing Plant at the Hanford Site would be added to the eligible facilities list. As part of the preparations to transfer the plutonium oxide under IAEA safeguards, samples of the powder were taken from the inventory to be shipped to the IAEA headquarters in Vienna, Austria, for laboratory analysis. The analysis of these samples was of high priority, and the IAEA requested that the material be shipped by aircraft, the most expeditious method

  17. Waste minimization at a plutonium processing facility

    International Nuclear Information System (INIS)

    Pillay, K.K.S.

    1995-01-01

    As part of Los Alamos National Laboratory's (LANL) mission to reduce the nuclear danger throughout the world, the plutonium processing facility at LANL maintains expertise and skills in nuclear weapons technologies as well as leadership in all peaceful applications of plutonium technologies, including fuel fabrication for terrestrial and space reactors and heat sources and thermoelectric generators for space missions. Another near-term challenge resulted from two safety assessments performed by the Defense Nuclear Facilities Safety Board and the U.S. Department of Energy during the past two years. These assessments have necessitated the processing and stabilization of plutonium contained in tons of residues so that they can be stored safely for an indefinite period. This report describes waste streams and approaches to waste reduction of plutonium management

  18. Investigation of plutonium abundance and age analysis

    Energy Technology Data Exchange (ETDEWEB)

    Huailong, Wu; Jian, Gong; Fanhua, Hao [China Academy of Engineering Physics, Mianyang (China). Inst. of Nuclear Physics and Chemistry

    2007-06-15

    Based on spectra analysis software, all of the plutonium material peak counts are analyzed. Relatively efficiency calibration is done by the non-coupling peaks of {sup 239}Pu. By using the known isotopes half life and yield, the coupling peaks counts are allocated by non-coupling peaks, consequently the atom ratios of each isotope are gotten. The formula between atom ratio and abundance or age is deduced by plutonium material isotopes decay characteristic. And so the abundance and age of plutonium material is gotten. After some re- peat measurements for a plutonium equipment are completed, a comparison between our analysis results and PC-FRAM and the owner's reference results are done. (authors)

  19. Plutonium gastrointestinal absorption by adults baboons

    International Nuclear Information System (INIS)

    Lataillade, G.; Madic, C.; Willemot, J.M.; Germain, P.; Colle, C.; Metivier, H.

    1991-01-01

    Gastrointestinal absorption of plutonium was investigated in baboons after ingestion of plutonium solution (oxidation states III; IV; V; VI), and plutonium incorporated in soya bean and winkles. We studied the effects of oxidation state and ingested mass for masses ranging from 0.35 μg to 51.6 x 10 +3 μg (4 x 10 -2 to 7776 μg of plutonium per kg of body weight). No clear increase in plutonium retention was shown for concentrations of plutonium smaller than 1 μg/kg. From 1 μg/kg to 1 mg/kg no effects of mass or oxidation state was observed and the mean fractional retention value was 10 -4 . For ingested masses higher than 1 mg/kg the fractional retention values respectively increased for Pu(V) and Pu(III) to (0.9 + 0.2) x 10 -2 and (7.4 + 4.1) x 10 -4 of the ingested mass. This increase might be due to the weak hydrolysis of these oxidation states which would increase gastrointestinal absorption by decrease of hydroxide formation. The fraction of plutonium retained after ingestion of soya bean was (3.0 + 0.5) x 10 -4 about 3 fold higher than the value for 238 Pu nitrate solution. No clear increase in plutonium retention was shown after ingestion of winkles containing 238 Pu. In conclusion, except for high masses of ingested Pu, the retention of which could reach 1% of the ingested dose, our results show that the gastrointestinal transfer factor of 10 -4 proposed by ICRP for gastrointestinal absorption of soluble form of Pu is acceptable, but 10 -3 would provide better safety margin [fr

  20. United Kingdom experience in plutonium transportation

    International Nuclear Information System (INIS)

    1978-08-01

    Plutonium has already been transported within the UK over a period of 20 years and to destinations overseas since the early 60's. Experience is recounted with regard to the forms of plutonium transported, regulations, insurance, container design, mode of transport, volume of traffic, physical protection, safety analysis and costs. It is concluded that this traffic could be expanded in the future without danger to the community or the environment

  1. United Kingdom experience in plutonium transportation

    International Nuclear Information System (INIS)

    1978-11-01

    This paper describes the extensive experience of the UKAEA and British Nuclear Fuels Limited in transporting plutonium within the UK over the last 20 years and to destinations overseas since the early 1960s. The aspects covered include: the form of plutonium transported (nitrate, oxide, mixed oxide etc.); UK and international regulations (e.g. covering safety and safeguards matters); insurance; container design; mode of transport; physical protection; and a safety analysis. Costs are estimated to be largely independent of quantity

  2. Future role of plutonium technology in society

    International Nuclear Information System (INIS)

    Christensen, D.C.; Matthews, R.B.; Trapp, T.J.

    1995-01-01

    Until the fall of the Berlin Wall, there was a very clear programmatic use of plutonium: supporting the nuclear deterrent. Since the breakup of the Soviet Union, bilateral agreements concerning the cessation of nuclear testing and the dismantlement of large portions of the nuclear weapon stockpiles by the United States and the states of the former Soviet Union have resulted in new requirements concerning the management and disposition of nuclear materials. This report describes current issues pertaining to the requirements for plutonium management

  3. A world of horror full with plutonium

    International Nuclear Information System (INIS)

    Broda, E.

    1977-01-01

    This article discusses the possibility of building a nuclear-bomb out of plutonium which has been originated in civil-nuclear power plants and the causes of plutonium on the human-body. In an interview Prof. Broda warns that some countries have already used civil-nuclear-technique in order to produce nuclear-arms and that there are severe risks for the future. (kancsar)

  4. ZPR-9 airborne plutonium monitoring system

    International Nuclear Information System (INIS)

    Rusch, G.K.; McDowell, W.P.; Knapp, W.G.

    1975-01-01

    An airborne plutonium monitoring system which is installed in the ZPR-9 (Zero Power Reactor No. 9) facility at Argonne National Laboratory is described. The design and operational experience are discussed. This monitoring system utilizes particle size and density discrimination, alpha particle energy discrimination, and a background-subtraction techique operating in cascade to separate airborne-plutonium activity from other, naturally occurring, airborne activity. Relatively high sensitivity and reliability are achieved

  5. Plutonium deposits in lung tissues of Filipinos

    International Nuclear Information System (INIS)

    Natera, E.S.; Palad, L.J.H.; Ignacio, L.M.

    1989-01-01

    This initial report on the plutonium concentration in lungs of Filipino adults is based on four samples. The data obtained suggest that the average of concentration in lungs of Filipinos is similar to that observed in other countries. This could be attributed to fallout resulting from nuclear test explosions conducted by neighboring countries. The result of this study will be useful in initiating the establishment of plutonium burden of Filipinos. (ELC). 2 tabs

  6. Architectural Representation of Valence in the Limbic System

    Science.gov (United States)

    Namburi, Praneeth; Al-Hasani, Ream; Calhoon, Gwendolyn G; Bruchas, Michael R; Tye, Kay M

    2016-01-01

    In order to thrive, animals must be able to recognize aversive and appetitive stimuli within the environment and subsequently initiate appropriate behavioral responses. This assignment of positive or negative valence to a stimulus is a key feature of emotional processing, the neural substrates of which have been a topic of study for several decades. Until recently, the result of this work has been the identification of specific brain regions, such as the basolateral amygdala (BLA) and nucleus accumbens (NAc), as important to valence encoding. The advent of modern tools in neuroscience has allowed further dissection of these regions to identify specific populations of neurons signaling the valence of environmental stimuli. In this review, we focus upon recent work examining the mechanisms of valence encoding, and provide a model for the systematic investigation of valence within anatomically-, genetically-, and functionally defined populations of neurons. PMID:26647973

  7. Guidelines for international plutonium management: Overview and implications

    International Nuclear Information System (INIS)

    Bryson, M.C.; Fitzgerald, C.P.; Kincaid, C.

    1998-01-01

    In September, 1997, nine of the world's plutonium-using countries agreed to a set of guidelines for international plutonium management, with acceptances to be submitted to the International Atomic Energy Agency on December 1. Following three years of discussion, the guidelines provide a unified package of accepted rules for the storage, handling, and transportation of civil plutonium as well as military plutonium that has been declared as no longer required for defense purposes. New requirements include a formal declaration of national plutonium strategies, which will recognize the environmental, economic, and proliferation concerns and the consequent importance of balancing plutonium supply and demand. Nations will also make annual declaration of their non-military stockpiles of unirradiated plutonium, together with estimates of the plutonium content in spent reactor fuel. These guidelines represent the first formally accepted recognition of the need for plutonium management of this scope and could thus provide a partial basis for future monitoring and policy regimes

  8. Disposal of Surplus Weapons Grade Plutonium

    International Nuclear Information System (INIS)

    Alsaed, H.; Gottlieb, P.

    2000-01-01

    The Office of Fissile Materials Disposition is responsible for disposing of inventories of surplus US weapons-usable plutonium and highly enriched uranium as well as providing, technical support for, and ultimate implementation of, efforts to obtain reciprocal disposition of surplus Russian plutonium. On January 4, 2000, the Department of Energy issued a Record of Decision to dispose of up to 50 metric tons of surplus weapons-grade plutonium using two methods. Up to 17 metric tons of surplus plutonium will be immobilized in a ceramic form, placed in cans and embedded in large canisters containing high-level vitrified waste for ultimate disposal in a geologic repository. Approximately 33 metric tons of surplus plutonium will be used to fabricate MOX fuel (mixed oxide fuel, having less than 5% plutonium-239 as the primary fissile material in a uranium-235 carrier matrix). The MOX fuel will be used to produce electricity in existing domestic commercial nuclear reactors. This paper reports the major waste-package-related, long-term disposal impacts of the two waste forms that would be used to accomplish this mission. Particular emphasis is placed on the possibility of criticality. These results are taken from a summary report published earlier this year

  9. Plutonium Finishing Plant safety evaluation report

    International Nuclear Information System (INIS)

    1995-01-01

    The Plutonium Finishing Plant (PFP) previously known as the Plutonium Process and Storage Facility, or Z-Plant, was built and put into operation in 1949. Since 1949 PFP has been used for various processing missions, including plutonium purification, oxide production, metal production, parts fabrication, plutonium recovery, and the recovery of americium (Am-241). The PFP has also been used for receipt and large scale storage of plutonium scrap and product materials. The PFP Final Safety Analysis Report (FSAR) was prepared by WHC to document the hazards associated with the facility, present safety analyses of potential accident scenarios, and demonstrate the adequacy of safety class structures, systems, and components (SSCs) and operational safety requirements (OSRs) necessary to eliminate, control, or mitigate the identified hazards. Documented in this Safety Evaluation Report (SER) is DOE's independent review and evaluation of the PFP FSAR and the basis for approval of the PFP FSAR. The evaluation is presented in a format that parallels the format of the PFP FSAR. As an aid to the reactor, a list of acronyms has been included at the beginning of this report. The DOE review concluded that the risks associated with conducting plutonium handling, processing, and storage operations within PFP facilities, as described in the PFP FSAR, are acceptable, since the accident safety analyses associated with these activities meet the WHC risk acceptance guidelines and DOE safety goals in SEN-35-91

  10. A vision for environmentally conscious plutonium processing

    International Nuclear Information System (INIS)

    Avens, L.R.; Eller, P.G.; Christensen, D.C.; Miller, W.L.

    1998-01-01

    Regardless of individual technical and political opinions about the uses of plutonium, it is virtually certain that plutonium processing will continue on a significant global scale for many decades for the purposes of national defense, nuclear power, and remediation. An unavoidable aspect of plutonium processing is that radioactively contaminated gas, liquid, and solid waste streams are generated. These streams need to be handled in a manner that not only is in full compliance with today's laws but also will be considered environmentally and economically responsible now and in the future. In this regard, it is indeed ironic that the multibillion dollar and multidecade radioactive cleanup mortgage that the US Department of Energy (and its Russian counterpart) now owns resulted from waste management practices that were at the time in full legal compliance. It is now abundantly evident that in the long run, these practices have proven to be neither environmentally nor economically sound. Recent dramatic advances in actinide science and technology now make it possible to drastically minimize or even eliminate the problematic waste streams of traditional plutonium processing operations. Advanced technology thereby provides the means to avoid passing on to children and grandchildren significant environmental and economic legacies that traditional processing inevitably produces. The authors describe such a vision for plutonium processing that could be implemented fully within 5 yr at a facility such as the Los Alamos National Laboratory Plutonium Facility (TA55). As a significant bonus, even on this short timescale, the initial technology investment is handsomely returned in avoided waste management costs

  11. Pulmonary carcinogenesis from plutonium-containing particles

    International Nuclear Information System (INIS)

    Thomas, R.G.; Smith, D.M.; Anderson, E.C.

    1980-01-01

    Induction of lung tumors by various types of radiation is of paramount concern to the nuclear industry. The data presented were obtained by exposing the pulmonary system of Syrian hamsters to particles of zirconium oxide containing various amounts of either plutonium-238 or -239 as the alpha radiation source. These particles were injected intravenously and lodged permanently in the capillary bed of the lung. When less than 20% of the lung tissue was irradiated, simulating the ''hot particle'' mode, tumors were not evident with lung burdens up to 500 nCi plutonium. More diffuse irradiation significantly increased the tumor incidence, with lung burdens of 50 to 150 nCi. When plutonium-laden microspheres were administered intratracheally, tumor production was considerably increased and the addition of 3 mg of iron oxide intratracheally further increased the incidence. Using the zirconium oxide matrix for the carrier of plutonium in aerosol particles produced tumor incidences of up to 50% in Syrian hamsters exposed by inhalation. Initial pulmonary (alveolar) burdens reached 100 nCi of plutonium. Similar inhalation studies using plutonium dioxide alone (no matrix) failed to produce any increase in lung tumorigenesis. The results are discussed in terms of possible mechanisms necessary for lung carcinogenesis. (H.K.)

  12. Reclamation of plutonium from pyrochemical processing residues

    International Nuclear Information System (INIS)

    Gray, L.W.; Gray, J.H.; Holcomb, H.P.; Chostner, D.F.

    1987-04-01

    Savannah River Laboratory (SRL), Savannah River Plant (SRP), and Rocky Flats Plant (RFP) have jointly developed a process to recover plutonium from molten salt extraction residues. These NaCl, KCL, and MgCl 2 residues, which are generated in the pyrochemical extraction of 241 Am from aged plutonium metal, contain up to 25 wt % dissolved plutonium and up to 2 wt % americium. The overall objective was to develop a process to convert these residues to a pure plutonium metal product and discardable waste. To meet this objective a combination of pyrochemical and aqueous unit operations was used. The first step was to scrub the salt residue with a molten metal (aluminum and magnesium) to form a heterogeneous ''scrub alloy'' containing nominally 25 wt % plutonium. This unit operation, performed at RFP, effectively separated the actinides from the bulk of the chloride salts. After packaging in aluminum cans, the ''scrub alloy'' was then dissolved in a nitric acid - hydrofluoric acid - mercuric nitrate solution at SRP. Residual chloride was separated from the dissolver solution by precipitation with Hg 2 (NO 3 ) 2 followed by centrifuging. Plutonium was then separated from the aluminum, americium and magnesium using the Purex solvent extraction system. The 241 Am was diverted to the waste tank farm, but could be recovered if desired

  13. A vision for environmentally conscious plutonium processing

    International Nuclear Information System (INIS)

    Avens, L.R.; Eller, P.G.; Christensen, D.C.; Miller, W.L.

    1998-01-01

    Regardless of individual technical and political opinions about the uses of plutonium, it is virtually certain that plutonium processing will continue on a significant global scale for many decades for the purposes of national defense, nuclear power and remediation. An unavoidable aspect of plutonium processing is that radioactive contaminated gas, liquid, and solid streams are generated. These streams need to be handled in a manner that is not only in full compliance with today's laws,but also will be considered environmentally and economically responsible now and in the future. In this regard, it is indeed ironic that the multibillion dollar and multidecade radioactive cleanup mortgage that the US Department of Energy (and its Russian counterpart) now owns resulted from waste management practices that were at the time in full legal compliance. The theme of this paper is that recent dramatic advances in actinide science and technology now make it possible to drastically minimize or even eliminate the problematic waste streams of traditional plutonium processing operations. Advanced technology thereby provides the means to avoid passing on to our children and grandchildren significant environmental and economic legacies that traditional processing inevitably produces. This paper will describe such a vision for plutonium processing that could be implemented fully within five years at a facility such as the Los Alamos Plutonium Facility (TA55). As a significant bonus, even on this short time scale, the initial technology investment is handsomely returned in avoided waste management costs

  14. Complementary technologies for verification of excess plutonium

    International Nuclear Information System (INIS)

    Langner, D.G.; Nicholas, N.J.; Ensslin, N.; Fearey, B.L.; Mitchell, D.J.; Marlow, K.W.; Luke, S.J.; Gosnell, T.B.

    1998-01-01

    Three complementary measurement technologies have been identified as candidates for use in the verification of excess plutonium of weapons origin. These technologies: high-resolution gamma-ray spectroscopy, neutron multiplicity counting, and low-resolution gamma-ray spectroscopy, are mature, robust technologies. The high-resolution gamma-ray system, Pu-600, uses the 630--670 keV region of the emitted gamma-ray spectrum to determine the ratio of 240 Pu to 239 Pu. It is useful in verifying the presence of plutonium and the presence of weapons-grade plutonium. Neutron multiplicity counting is well suited for verifying that the plutonium is of a safeguardable quantity and is weapons-quality material, as opposed to residue or waste. In addition, multiplicity counting can independently verify the presence of plutonium by virtue of a measured neutron self-multiplication and can detect the presence of non-plutonium neutron sources. The low-resolution gamma-ray spectroscopic technique is a template method that can provide continuity of knowledge that an item that enters the a verification regime remains under the regime. In the initial verification of an item, multiple regions of the measured low-resolution spectrum form a unique, gamma-radiation-based template for the item that can be used for comparison in subsequent verifications. In this paper the authors discuss these technologies as they relate to the different attributes that could be used in a verification regime

  15. Radiation damage and annealing in plutonium tetrafluoride

    Science.gov (United States)

    McCoy, Kaylyn; Casella, Amanda; Sinkov, Sergey; Sweet, Lucas; McNamara, Bruce; Delegard, Calvin; Jevremovic, Tatjana

    2017-12-01

    A sample of plutonium tetrafluoride that was separated prior to 1966 at the Hanford Site in Washington State was analyzed at the Pacific Northwest National Laboratory (PNNL) in 2015 and 2016. The plutonium tetrafluoride, as received, was an unusual color and considering the age of the plutonium, there were questions about the condition of the material. These questions had to be answered in order to determine the suitability of the material for future use or long-term storage. Therefore, thermogravimetric/differential thermal analysis and X-ray diffraction evaluations were conducted to determine the plutonium's crystal structure, oxide content, and moisture content; these analyses reported that the plutonium was predominately amorphous and tetrafluoride, with an oxide content near ten percent. Freshly fluorinated plutonium tetrafluoride is known to be monoclinic. During the initial thermogravimetric/differential thermal analyses, it was discovered that an exothermic event occurred within the material near 414 °C. X-ray diffraction analyses were conducted on the annealed tetrafluoride. The X-ray diffraction analyses indicated that some degree of recrystallization occurred in conjunction with the 414 °C event. The following commentary describes the series of thermogravimetric/differential thermal and X-ray diffraction analyses that were conducted as part of this investigation at PNNL.

  16. Radiation damage and annealing in plutonium tetrafluoride

    International Nuclear Information System (INIS)

    McCoy, Kaylyn; Casella, Amanda; Sinkov, Sergey

    2017-01-01

    A sample of plutonium tetrafluoride that was separated prior to 1966 at the Hanford Site in Washington State was analyzed at the Pacific Northwest National Laboratory (PNNL) in 2015 and 2016. The plutonium tetrafluoride, as received, was an unusual color and considering the age of the plutonium, there were questions about the condition of the material. These questions had to be answered in order to determine the suitability of the material for future use or long-term storage. Therefore, thermogravimetric/differential thermal analysis and X-ray diffraction evaluations were conducted to determine the plutonium's crystal structure, oxide content, and moisture content; these analyses reported that the plutonium was predominately amorphous and tetrafluoride, with an oxide content near ten percent. Freshly fluorinated plutonium tetrafluoride is known to be monoclinic. And during the initial thermogravimetric/differential thermal analyses, it was discovered that an exothermic event occurred within the material near 414 °C. X-ray diffraction analyses were conducted on the annealed tetrafluoride. The X-ray diffraction analyses indicated that some degree of recrystallization occurred in conjunction with the 414 °C event. This commentary describes the series of thermogravimetric/differential thermal and X-ray diffraction analyses that were conducted as part of this investigation at PNNL.

  17. Gamma spectrometric methods for measuring plutonium

    International Nuclear Information System (INIS)

    Gunnink, R.

    1978-01-01

    Nondestructive analyses of plutonium can be made by detecting and measuring the gamma rays emitted by a sample. Although qualitative and semiquantitative assays can be performed with relative ease, only recently have methods been developed, using computer analysis techniques, that provide quantitative results. This paper reviews some new techniques developed for measuring plutonium. The features of plutonium gamma-ray spectra are reviewed and some of the computer methods used for spectrum analysis are discussed. The discussion includes a description of a powerful computer method of unfolding complex peak multiplets that uses the standard linear least-squares techniques of data analysis. This computer method is based on the generation of response profiles for the isotopes composing a plutonium sample and requires a description of the peak positions, relative intensities, and line shapes. The principles that plutonium isotopic measurements are based on are also developed, followed by illustrations of the measurement procedures as applied to the quantitative analysis of plutonium liquid and solid samples

  18. Nondestructive assay of plutonium residue in horizontal storage tanks

    International Nuclear Information System (INIS)

    Marsh, S.F.

    1985-01-01

    Aqueous plutonium recovery and purification processes often involve the temporary storage of plutonium solutions in holding tanks. Because plutonium is known to precipitate from aqueous solutions under certain conditions, there is a continuing need to assay emptied tanks for plutonium residue. A portable gamma spectrometer system, specifically designed for this purpose, provides rapid assay of such plutonium residues in horizontal storage tanks. A means is thus available for the nondestructive analysis of these tanks on a regular schedule to ensure that significant deposits of plutonium are not allowed to accumulate. 5 figs

  19. Civil plutonium held in France in December 31, 2000

    International Nuclear Information System (INIS)

    2002-02-01

    Spent fuels comprise about 1% of plutonium which is separated during the reprocessing and recycled to prepare the mixed uranium-plutonium fuel (MOX), which in turn is burnt in PWRs. Plutonium can be in a non-irradiated or separated form, or in an irradiated form when contained in the spent fuel. Each year, in accordance with the 1997 directives relative to the management of plutonium, France has to make a status of its civil plutonium stock and communicate it to the IAEA using a standard model form. This short document summarizes the French plutonium stocks at the end of 1999 and 2000. (J.S.)

  20. Plutonium uptake by plants from soil containing plutonium-238 dioxide particles. Final report

    International Nuclear Information System (INIS)

    Brown, K.W.; McFarlane, J.C.

    1977-05-01

    Three plant species--alfalfa, lettuce, and radishes were grown in soils contaminated with plutonium-238 dioxide (238)PuO2 at concentrations of 23, 69, 92, and 342 nanocuries per gram (nCi/g). The length of exposure varied from 60 days for the lettuce and radishes to 358 days for the alfalfa. The magnitude of plutonium incorporation as indicated by the discrimination ratios for these species, after being exposed to the relatively insoluble PuO2, was similar to previously reported data using different chemical forms of plutonium. Evidence indicates that the predominant factor in plutonium uptake by plants may involve the chelation of plutonium contained in the soils by the action of compounds such as citric acid and/or other similar chelating agents released from the plant roots

  1. Cycle downstream: the plutonium question; Aval du cycle la question du plutonium

    Energy Technology Data Exchange (ETDEWEB)

    Zask, G [Electricite de France, EDF/DAC, 75 - Paris (France); Rome, M [Electricite de France, EDF, Service Etudes et Projets Thermiques et Nucleaires, 92 - Courbevoie (France); Delpech, M [CEA Cadarache, Dept. d' Etudes des Reacteurs/SPRC, 13 - Saint-Paul-lez-Durance (France); and others

    1998-06-29

    This day, organized by the SFEN, took place at Paris the 4 june 1998. Nine papers were presented. They take stock on the plutonium physics and its utilization as a nuclear fuel. This day tried to bring information to answer the following questions: do people have to keep the plutonium in the UOX fuel or in the MOX fuel in order to use it for future fast reactors? Do people have to continue obstinately the plutonium reprocessing in the MOX for the PWR type reactors? Will it be realized a underground disposal? Can it be technically developed plutonium incinerators and is it economically interesting? The plutonium physics, the experimental programs and the possible solutions are presented. (A.L.B.)

  2. Gamma ray NDA assay system for total plutonium and isotopics in plutonium product solutions

    International Nuclear Information System (INIS)

    Cowder, L.R.; Hsue, S.T.; Johnson, S.S.; Parker, J.L.; Russo, P.A.; Sprinkle, J.K.; Asakura, Y.; Fukuda, T.; Kondo, I.

    1979-01-01

    A LASL-designed gamma-ray NDA instrument for assay of total plutonium and isotopics of product solutions at Tokai-Mura is currently installed and operating. The instrument is, optimally, a densitometer that uses radioisotopic sources for total plutonium measurements at the K absorption edge. The measured transmissions of additional gamma-ray lines from the same radioisotopic sources are used to correct for self-attenuation of passive gamma rays from plutonium. The corrected passive data give the plutonium isotopic content of freshly separated to moderately aged solutions. This off-line instrument is fully automated under computer control, with the exception of sample positioning, and operates routinely in a mode designed for measurement control. A one-half percent precision in total plutonium concentration is achieved with a 15-minute measurement

  3. Emotion and language: Valence and arousal affect word recognition

    Science.gov (United States)

    Brysbaert, Marc; Warriner, Amy Beth

    2014-01-01

    Emotion influences most aspects of cognition and behavior, but emotional factors are conspicuously absent from current models of word recognition. The influence of emotion on word recognition has mostly been reported in prior studies on the automatic vigilance for negative stimuli, but the precise nature of this relationship is unclear. Various models of automatic vigilance have claimed that the effect of valence on response times is categorical, an inverted-U, or interactive with arousal. The present study used a sample of 12,658 words, and included many lexical and semantic control factors, to determine the precise nature of the effects of arousal and valence on word recognition. Converging empirical patterns observed in word-level and trial-level data from lexical decision and naming indicate that valence and arousal exert independent monotonic effects: Negative words are recognized more slowly than positive words, and arousing words are recognized more slowly than calming words. Valence explained about 2% of the variance in word recognition latencies, whereas the effect of arousal was smaller. Valence and arousal do not interact, but both interact with word frequency, such that valence and arousal exert larger effects among low-frequency words than among high-frequency words. These results necessitate a new model of affective word processing whereby the degree of negativity monotonically and independently predicts the speed of responding. This research also demonstrates that incorporating emotional factors, especially valence, improves the performance of models of word recognition. PMID:24490848

  4. The handling of plutonium hexafluoride (1962); Manipulation de l'hexafluorure de plutonium (1962)

    Energy Technology Data Exchange (ETDEWEB)

    Berard, Ph [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

    1961-11-15

    The major problem posed in this work is the instability of plutonium hexafluoride. The influence of various factors on the decomposition of the fluoride has been studied: physical aspect of the walls, nature of the metal and its pretreatment, influence of the temperature. A means of detecting plutonium-239 in a metallic apparatus by {gamma}-ray counting has been developed; the sensitivity is of the order of half a milligram, but the precision is very low (about 50 per cent). Yields of over 95 per cent have been obtained for the transfer of plutonium during the preparation and sublimation of the hexafluoride. This study confirms the possibility of using plutonium hexafluoride for the extraction of plutonium from irradiated fuel elements by a dry method. (author) [French] Le probleme majeur de cette etude a ete l'instabilite de l'hexafluorure de plutonium. Nous avons etudie l'influence de divers facteurs sur la decomposition de l'hexafluorure: aspect physique des parois, nature du metal et de son pretraitement, influence de la temperature. Nous avons mis au point un mode de detection du plutonium-239 dans un appareillage metallique par comptage du rayonnement {gamma}; la sensibilite est de l'ordre du demi-milligramme, mais la precision est tres faible (50 pour cent environ). Nous avons obtenu des rendements depassant 95 pour cent dans le transfert du plutonium au cours de la fabrication et de la sublimation de l'hexafluorure. Cette etude confirme la possibilite d'utiliser l'hexafluorure de plutonium dans l'extraction du plutonium des combustibles irradies par voie seche. (auteur)

  5. Beiological behaviour of plutonium 239

    International Nuclear Information System (INIS)

    Lafuma, J.

    1976-01-01

    Plutonium is scarcely incorporated from the environment into the food chain because of its unability to penetrate biological membranes. Workers can be contaminated through inhalation or deposition in wounds. Pu present in the pulmonary alveoles or incorporated in wounds is redistributed in the organism either through cellular transport resulting in an important accumulation in the lymphatic ganglia either by blood transport as dissolved Pu bound to proteins. This mechanism results in a progressive accumulation of the radioelement in liver and bone. It is estimated that about 40% of the Pu present in the blood is deposited in the liver from which one half is eliminated every ten years. 50% is deposited in bone from which the elimination takes much longer and 10% is eliminated with the urines. Intravenous injection of DIPA is very useful for Pu elimination immediately after contamination. For elimination of pulmonary Pu the technique of ''pulmonary washing'' is suggested. This method reduces the pulmonary contamination in laboratory aniamls by a factor 10. (author)

  6. Plutonium dioxide dissolution in glass

    Energy Technology Data Exchange (ETDEWEB)

    Vienna, J.D.; Alexander, D.L.; Li, Hong [and others

    1996-09-01

    In the aftermath of the Cold War, the U.S. Department of Energy`s (DOE) Office of Fissile Materials Disposition (OFMD) is charged with providing technical support for evaluation of disposition options for excess fissile materials manufactured for the nation`s defense. One option being considered for the disposition of excess plutonium (Pu) is immobilization by vitrification. The vitrification option entails immobilizing Pu in a host glass and waste package that are criticality-safe (immune to nuclear criticality), proliferation-resistant, and environmentally acceptable for long-term storage or disposal. To prove the technical and economic feasibility of candidate vitrification options it is necessary to demonstrate that PuO{sub 2} feedstock can be dissolved in glass in sufficient quantity. The OFMD immobilization program has set a Pu solubility goal of 10 wt% in glass. The life cycle cost of the vitrification options are strongly influenced by the rate at which PUO{sub 2} dissolves in glass. The total number of process lines needed for vitrification of 50 t of Pu in 10 years is directly dependent upon the time required for Pu dissolution in glass. The objective of this joint Pacific Northwest National Laboratory (PNNL) - Savannah River Technology Center (SRTC) study was to demonstrate a high Pu solubility in glass and to identify on a rough scale the time required for Pu dissolution in the glass. This study was conducted using a lanthanide borosilicate (LaBS) glass composition designed at the SRTC for the vitrification of actinides.

  7. Plutonium storage thermal analysis (U)

    International Nuclear Information System (INIS)

    Hensel, S.J.; Lee, S.Y.; Schaade, J.B.

    1997-01-01

    Thermal modeling of plutonium metal ingots stored in food pack cans provides information useful for performing stored material safety evaluations. Four storage can geometries were modeled, and several conclusions can be made from the 14 cases analyzed. The ingot temperature increased from 7 degrees F to 12 degrees F (depending on can configuration) per additional watt of power. Including internal convection lowers computed ingot temperatures by 70 degrees F. Accounting for the heat flow through the bottom of the cans to the storage rack lowered computed ingot temperatures by an additional 70 degrees F to 80 degrees F. In the rimmed can systems storing ingots with a power of 10.35 watts, the ingot temperature varies from 190 degrees F to 213 degrees F. Including a plastic bag between the inner and outer can increases the ingot temperature by 15 degrees F. Adding a label to the outer can side reduces the outer can side temperature by 13 degrees F. Changes in ambient temperature affect the outer can temperatures more than the ingot temperature by a factor of 3. Similarly, a 5 degrees F drop in outer can temperature due to increased convection lowered the ingot temperature by only 2 degrees F

  8. Plutonium dioxide dissolution in glass

    International Nuclear Information System (INIS)

    Vienna, J.D.; Alexander, D.L.; Li, Hong

    1996-09-01

    In the aftermath of the Cold War, the U.S. Department of Energy's (DOE) Office of Fissile Materials Disposition (OFMD) is charged with providing technical support for evaluation of disposition options for excess fissile materials manufactured for the nation's defense. One option being considered for the disposition of excess plutonium (Pu) is immobilization by vitrification. The vitrification option entails immobilizing Pu in a host glass and waste package that are criticality-safe (immune to nuclear criticality), proliferation-resistant, and environmentally acceptable for long-term storage or disposal. To prove the technical and economic feasibility of candidate vitrification options it is necessary to demonstrate that PuO 2 feedstock can be dissolved in glass in sufficient quantity. The OFMD immobilization program has set a Pu solubility goal of 10 wt% in glass. The life cycle cost of the vitrification options are strongly influenced by the rate at which PUO 2 dissolves in glass. The total number of process lines needed for vitrification of 50 t of Pu in 10 years is directly dependent upon the time required for Pu dissolution in glass. The objective of this joint Pacific Northwest National Laboratory (PNNL) - Savannah River Technology Center (SRTC) study was to demonstrate a high Pu solubility in glass and to identify on a rough scale the time required for Pu dissolution in the glass. This study was conducted using a lanthanide borosilicate (LaBS) glass composition designed at the SRTC for the vitrification of actinides

  9. Intersite interactions and susceptibility in mixed valence systems

    International Nuclear Information System (INIS)

    Xiaoqian Wang; Gao Lin; Bingjian Ni; Fusui Liu.

    1985-10-01

    This paper considers the effect of intersite processes on the susceptibility in mixed valence system. The method of thermodynamical perturbation used in this paper can also be generalized to study other properties of mixed valence system. The general formula of partition function of two-site interactions for the mixed valence system is given. The numerical calculations show that the intersite interaction is large enough to explain the minimum of susceptibility discovered in experiments. The different types of our theoretical curves predict that the susceptibility should exhibit a rich variety of behaviour at low temperature for various materials. (author)

  10. Valence bond model potential energy surface for H4

    International Nuclear Information System (INIS)

    Silver, D.M.; Brown, N.J.

    1980-01-01

    Potential energy surfaces for the H 4 system are derived using the valence bond procedure. An ab initio evaluation of the valence bond energy expression is described and some of its numerical properties are given. Next, four semiempirical evaluations of the valence bond energy are defined and parametrized to yield reasonable agreement with various ab initio calculations of H 4 energies. Characteristics of these four H 4 surfaces are described by means of tabulated energy minima and equipotential contour maps for selected geometrical arrangements of the four nuclei

  11. Valence, magnetism and conduction in the intermediate valence compounds: the case SmB6

    International Nuclear Information System (INIS)

    Derr, J.

    2006-09-01

    In some rare earth based compounds, the 4f level is situated so close to the Fermi level that the valence of the compound can become intermediate between two integer values. The so called 'intermediate valence' compound of Samarium hexaboride (SmB 6 ) is one typical example of the exciting physics which can result from this quantum equilibrium between two valence configurations. The first configuration (Sm 2+ ) corresponds to an insulating and non magnetic state whereas the second one (Sm 3+ ) would theoretically give a magnetic and metallic ground state. This dissertation deals with the influence of pressure on this equilibrium. Specific heat measurements under pressure evidenced a new long range magnetic ordering for pressures higher than p c ∼ 10 GPa. On another hand, transport measurements measured for the first time in good conditions of hydrostatics found a reliable and reproducible critical pressure for the insulator to metal transition equal to p c . The phase diagram of SmB 6 is now well known and the observation for the first time of a magnetic anomaly in the high pressure resistivity curves certifies that the onset of the magnetic phase really coincide with the closure of the gap. This change at the critical pressure p c is discussed in a general frame taking into account the Kondo lattice temperature as a key parameter for the renormalization of the wavefunction from one integer configuration to the other whereas the valence itself is still intermediate. This general idea seems to be valid also for other systems studied in this dissertation like SmS or TmSe and could even be valid for more general cases (Ytterbium, Cerium). In the same time, resistivity measurements under uniaxial stress were undertaken. The result is a strong anisotropy effect observed on the pressure dependence of the residual resistivity in the compound SmB 6 . The comparison with the transport under hydrostatic conditions enables us to consider a new idea for the nature of the gap

  12. Effect of compositional variation in plutonium on process shielding design

    International Nuclear Information System (INIS)

    Brown, T.H.

    1997-11-01

    Radiation dose rate from plutonium with high 239 Pu content varies with initial nuclidic content, radioactive decay time, and impurity elemental content. The two idealized states of old plutonium and clean plutonium, whose initial compositions are given, provide approximate upper and lower bounds on dose rate variation. Whole-body dose rates were calculated for the two composition states, using unshielded and shielded plutonium spheres of varying density. The dose rates from these variable density spheres are similar to those from expanded plutonium configurations encountered during processing. The dose location of 40 cm from the sphere center is representative of operator standoff for direct handling of plutonium inside a glove box. The results have shielding implications for glove boxes with only structurally inherent shielding, especially for processing of old plutonium in an expanded configuration. Further reduction in total dose rate by using lead to reduce photon dose rate is shown for two density cases representing compact and expanded plutonium configurations

  13. Light water breeder reactor using a uranium-plutonium cycle

    International Nuclear Information System (INIS)

    Radkowsky, A.; Chen, R.

    1990-01-01

    This patent describes a light water receptor (LWR) for breeding fissile material using a uranium-plutonium cycle. It comprises: a prebreeder section having plutonium fuel containing a Pu-241 component, the prebreeder section being operable to produce enriched plutonium having an increased Pu-241 component; and a breeder section for receiving the enriched plutonium from the prebreeder section, the breeder section being operable for breeding fissile material from the enriched plutonium fuel. This patent describes a method of operating a light water nuclear reactor (LWR) for breeding fissile material using a uranium-plutonium cycle. It comprises: operating the prebreeder to produce enriched plutonium fuel having an increased Pu-241 component; fueling a breeder section with the enriched plutonium fuel to breed the fissile material

  14. Effect of compositional variation in plutonium on process shielding design

    Energy Technology Data Exchange (ETDEWEB)

    Brown, T.H.

    1997-11-01

    Radiation dose rate from plutonium with high {sup 239}Pu content varies with initial nuclidic content, radioactive decay time, and impurity elemental content. The two idealized states of old plutonium and clean plutonium, whose initial compositions are given, provide approximate upper and lower bounds on dose rate variation. Whole-body dose rates were calculated for the two composition states, using unshielded and shielded plutonium spheres of varying density. The dose rates from these variable density spheres are similar to those from expanded plutonium configurations encountered during processing. The dose location of 40 cm from the sphere center is representative of operator standoff for direct handling of plutonium inside a glove box. The results have shielding implications for glove boxes with only structurally inherent shielding, especially for processing of old plutonium in an expanded configuration. Further reduction in total dose rate by using lead to reduce photon dose rate is shown for two density cases representing compact and expanded plutonium configurations.

  15. Absorption of plutonium in the iron-deficient rat

    International Nuclear Information System (INIS)

    Ragan, H.A.

    1977-01-01

    Iron deficiency did not enhance absorption of plutonium following intragastric gavage of rats. Absorption of plutonium citrate in both control and iron-deficient rats was about 0.03% of the administered dose

  16. Model of plutonium dynamics in a deciduous forest ecosystem

    International Nuclear Information System (INIS)

    Garten, C.T. Jr.; Gardner, R.H.; Dahlman, R.C.

    1980-01-01

    A linear compartment model with donor-controlled flows between compartments was designed to describe and simulate the behavior of plutonium ( 239 240 Pu) in a contaminated forest ecosystem at Oak Ridge, TN. At steady states predicted by the model, less than 0.25% of the plutonium in the ecosystem resides in biota. Soil is the major repository of plutonium in the forest, and exchanges of plutonium between soil and litter or soil and tree roots were dominant transfers affecting the ecosystem distribution of plutonium. Variation in predicted steady-state amounts of plutonium in the forest, given variability in the model parameters, indicates that our ability to develop models of plutonium transport in ecosystems should improve with greater precision in data from natural environments and a better understanding of sources of variation in plutonium data

  17. Mechanism of plutonium metal dissolution in HNO3-HF-N2H4 solution

    International Nuclear Information System (INIS)

    Karraker, D.G.

    1985-01-01

    An oxidation-reduction balance of the products of the dissolution of plutonium metal and alloys in HNO 3 -HF-N 2 H 4 solution shows that the major reactions during dissolution are the reduction of nitrate to NH 3 , N 2 and N 2 O by the metal, and the oxidation of H free radicals to NH 3 by N 2 H 4 . Reactions between HNO 3 and N 2 H 4 produce varying amounts of HN 3 . The reaction rate is greater for delta-Pu than alpha-Pu, and is increased by higher concentrations of HF and HNO 3 . The low yield of reduced nitrogen species indicates that nitrate is reduced on the metal surface without producing a significant concentration of species that react with N 2 H 4 . It is conjectured that intermediate Pu valences and electron transfer within the metal are involved. 7 refs., 3 tabs

  18. Plutonium spot of mixed oxide fuel, 2

    International Nuclear Information System (INIS)

    Suzuki, Yukio; Maruishi, Yoshihiro; Satoh, Masaichi; Aoki, Toshimasa; Muto, Tadashi

    1974-01-01

    In a fast reactor, the specification for the homogeneity of plutonium in plutonium-uranium mixed-oxide fuel is mainly dependent on the nuclear characteristics, whereas in a thermal reactor, on thermal characteristics. This homogeneity is measured by autoradiography as the plutonium spot size of the specimens which are arbitrarily chosen fuel pellets from a lot. Although this is a kind of random sampling, it is difficult to apply this method to conventional digital standards including JIS standards. So a special sampling inspection method was studied. First, it is assumed that the shape of plutonium spots is spherical, the size distribution is logarithmic normal, and the standard deviation is constant. Then, if standard deviation and mean spot size are given, the logarithmic normal distribution is decided unitarily, and further if the total weight of plutonium spots for a lot of pellets is known, the number of the spots (No) which does not conform to the specification can be obtained. Then, the fraction defective is defined as No devided by the number of pellets per lot. As to the lot with such fraction defective, the acceptance coefficient of the lot was obtained through calculation, in which the number of sampling, acceptable diameter limit observed and acceptable conditions were used as parameters. (Tai, I.)

  19. Multiple recycling of plutonium in advanced PWRs

    International Nuclear Information System (INIS)

    Kloosterman, J.L.

    1998-04-01

    The influence of the moderator-to-fuel ratio in MOX fueled PWRs on the moderator void coefficient, the fuel temperature coefficient, the moderator temperature coefficient, the boron reactivity worth, the critical boron concentration, the mean neutron generation time and the effective delayed neutron fraction has been assessed. Increasing the moderator-to-fuel ratio to values larger than three, gives a moderator void coefficient sufficiently large to recycle the plutonium at least four times. Scenario studies show that four times recycling of plutonium in PWRs reduces the plutonium mass produced with a factor of three compared with a reference once-through reactor park, but that the americium and curium production triple. If the minor actinides and the remaining plutonium after four times recycling are disposed of, the reduction of the radiotoxicity reaches only a factor of two. This factor increases to five at the maximum when the plutonium is further recycled. Recycling of americium and curium is needed to further reduce the radiotoxicity of the spent fuel. 4 refs

  20. Japan's spent fuel and plutonium management challenge

    International Nuclear Information System (INIS)

    Katsuta, Tadahiro; Suzuki, Tatsujiro

    2011-01-01

    Japan's commitment to plutonium recycling has been explicitly stated in its long-term program since 1956. Despite the clear cost disadvantage compared with direct disposal or storage of spent fuel, the Rokkasho reprocessing plant started active testing in 2006. Japan's cumulative consumption of plutonium has been only 5 tons to date and its future consumption rate is still uncertain. But once the Rokkasho reprocessing plant starts its full operation, Japan will separate about 8 tons of plutonium annually. Our analysis shows that, with optimum use of available at-reactor and away-from-reactor storage capacity, there would be no need for reprocessing until the mid-2020s. With an additional 30,000 tons of away-from-reactor (AFR) spent-fuel storage capacity reprocessing could be avoided until 2050. Deferring operation of the Rokkasho plant, at least until the plutonium stockpile had been worked down to the minimum required level, would also minimize international concern about Japan's plutonium stockpile. The authors are happy to acknowledge Frank von Hippel, Harold Feiveson, Jungming Kang, Zia Mian, M.V. Ramana, and other IPFM members, as well as the generous grant from the MacArthur Foundation for helping make this research possible.

  1. Plutonium Chemistry in the UREX+ Separation Processes

    Energy Technology Data Exchange (ETDEWEB)

    ALena Paulenova; George F. Vandegrift, III; Kenneth R. Czerwinski

    2009-10-01

    The project "Plutonium Chemistry in the UREX+ Separation Processes” is led by Dr. Alena Paulenova of Oregon State University under collaboration with Dr. George Vandegrift of ANL and Dr. Ken Czerwinski of the University of Nevada at Las Vegas. The objective of the project is to examine the chemical speciation of plutonium in UREX+ (uranium/tributylphosphate) extraction processes for advanced fuel technology. Researchers will analyze the change in speciation using existing thermodynamics and kinetic computer codes to examine the speciation of plutonium in aqueous and organic phases. They will examine the different oxidation states of plutonium to find the relative distribution between the aqueous and organic phases under various conditions such as different concentrations of nitric acid, total nitrates, or actinide ions. They will also utilize techniques such as X-ray absorbance spectroscopy and small-angle neutron scattering for determining plutonium and uranium speciation in all separation stages. The project started in April 2005 and is scheduled for completion in March 2008.

  2. Guidelines for the responsible management of plutonium

    International Nuclear Information System (INIS)

    Agrell, P.H.

    1997-01-01

    Since 1994 an informal group of representatives of States party to the NPT has been trying to develop agreed international guidelines for the responsible management of non-military plutonium. This paper gives a brief description of the outcome. Since the results are still subject to decision by Governments, the description must be in general terms only. The paper describes the background to, and genesis of, the discussions and the general approach taken, which was based on commitment to the NPT, national responsibility for the management of nuclear materials and the fuel cycle, upholding of the IAEA's safeguards system, and a focus on civil material. An indication is given of the development of the Group's thinking, especially the decisions that any guidelines must be capable of accommodating surplus military plutonium, as well as civil, and that the main focus should be on measures to increase transparency. The resulting guidelines are described. Their main features are a re-statement of commitments and standards for the management of non-military plutonium with regard to non-proliferation, safety, and other fields, a commitment to the management of such plutonium according to a consistent national strategy, and a commitment to the publication of information on that strategy, and of annual statistics for holdings of plutonium in a consistent format. Other aspects of the guidelines are also explained. Finally, an attempt is made to assess the possible practical effects of the guidelines if adopted by governments. (author)

  3. Measurements of plutonium in environmental samples

    Energy Technology Data Exchange (ETDEWEB)

    D' Alberti, F; Risposi, L [Instituto di Fisica Applicata, University of Milan, Milan (Italy)

    1996-01-01

    Within the activities connected with the start up of the PETRA Laboratory (Processo per l'Estrazione di Terre Rare ed Attinidi, i.e. process for extraction of rare earths and actinides), the Radiation Protection Unit of the J.R.C.-Ispra has carried out a well planned set of experimental measurements aimed at evaluating the zero point of the isotopes of plutonium in environmental samples by alfa spectrometry. After the International Moratorium in 1963, no release of plutonium has occurred in the environment apart from the burn up of SNAP 9A satellite in April 1964. Since then the plutonium concentration in air and in fallout samples has been continuously decreasing requiring, therefore, optimization of both instrumentation and experimental measurement procedures in order to obtain better sensibilities. In this work, the experimental methodology followed at the J.R.C.-Ispra for measurements of plutonium concentration in air, deposition and soil is described and the plutonium behaviour in these samples is reported and discussed starting from 1961.

  4. Measurements of plutonium in environmental samples

    International Nuclear Information System (INIS)

    D'Alberti, F.; Risposi, L.

    1996-01-01

    Within the activities connected with the start up of the PETRA Laboratory (Processo per l'Estrazione di Terre Rare ed Attinidi, i.e. process for extraction of rare earths and actinides), the Radiation Protection Unit of the J.R.C.-Ispra has carried out a well planned set of experimental measurements aimed at evaluating the zero point of the isotopes of plutonium in environmental samples by alfa spectrometry. After the International Moratorium in 1963, no release of plutonium has occurred in the environment apart from the burn up of SNAP 9A satellite in April 1964. Since then the plutonium concentration in air and in fallout samples has been continuously decreasing requiring, therefore, optimization of both instrumentation and experimental measurement procedures in order to obtain better sensibilities. In this work, the experimental methodology followed at the J.R.C.-Ispra for measurements of plutonium concentration in air, deposition and soil is described and the plutonium behaviour in these samples is reported and discussed starting from 1961

  5. Computerized plutonium laboratory-stack monitoring system

    International Nuclear Information System (INIS)

    Stafford, R.G.; DeVore, R.K.

    1977-01-01

    The Los Alamos Scientific Laboratory has recently designed and constructed a Plutonium Research and Development Facility to meet design criteria imposed by the United States Energy Research and Development Administration. A primary objective of the design criteria is to assure environmental protection and to reliably monitor plutonium effluent via the ventilation exhaust systems. A state-of-the-art facility exhaust air monitoring system is described which establishes near ideal conditions for evaluating plutonium activity in the stack effluent. Total and static pressure sensing manifolds are incorporated to measure average velocity and integrated total discharge air volume. These data are logged at a computer which receives instrument data through a multiplex scanning system. A multipoint isokinetic sampling assembly with associated instrumentation is described. Continuous air monitors have been designed to sample from the isokinetic sampling assembly and transmit both instantaneous and integrated stack effluent concentration data to the computer and various cathode ray tube displays. The continuous air monitors also serve as room air monitors in the plutonium facility with the primary objective of timely evacuation of personnel if an above tolerance airborne plutonium concentration is detected. Several continuous air monitors are incorporated in the ventilation system to assist in identification of release problem areas

  6. Radiation damage and annealing in plutonium tetrafluoride

    Energy Technology Data Exchange (ETDEWEB)

    McCoy, Kaylyn; Casella, Amanda; Sinkov, Sergey; Sweet, Lucas; McNamara, Bruce; Delegard, Calvin; Jevremovic, Tatjana

    2017-12-01

    Plutonium tetrafluoride that was separated prior to 1966 at the Hanford Site in Washington State was analyzed at the Pacific Northwest National Laboratory (PNNL) in 2015 and 2016. The plutonium tetrafluoride, as received, was an off-normal color and considering the age of the plutonium, there were questions about the condition of the material. These questions had to be answered in order to determine the suitability of the material for future use or long-term storage. Therefore, Thermogravimetric/Differential Thermal Analysis and X-ray Diffraction evaluations were conducted to determine the plutonium’s crystal structure, oxide content, and moisture content; these analyses reported that the plutonium was predominately amorphous and tetrafluoride, with an oxide content near ten percent. Freshly fluorinated plutonium tetrafluoride is known to be monoclinic. During the initial Thermogravimetric/Differential Thermal analyses, it was discovered that an exothermic event occurred within the material near 414°C. X-ray Diffraction analyses were conducted on the annealed tetrafluoride. The X-ray Diffraction analyses indicated that some degree of recrystallization occurred in conjunction with the 414°C event. The following commentary describes the series of Thermogravimetric/Differential Thermal and X-ray Diffraction analyses that were conducted as part of this investigation at PNNL, in collaboration with the University of Utah Nuclear Engineering Program.

  7. The use of plutonium in Swedish reactors

    International Nuclear Information System (INIS)

    Forsstroem, H.

    1982-09-01

    The report deals with the utilization of plutonium in Swedish nuclear power plants. The plutonium content of the mixed oxide fuel will normally be 3-7 per cent. The processing of spent nuclear fuel will produce about 6 ton plutonium. The use of mixed oxide fuel in Forsmark 3 and Oskarshamn 3 is discussed. The fuel cycle will start with the manufacturing of the fuel elements abroad and proceeds with transport and utilization, storing of spent fuel about 40 years in Sweden followed by direct disposal. The manufacture and use of mixed oxide (MOX) fuel is based on well-known techniques. Approximately 20 000 MOX fuel rods have been irradiated and the fuel is essentially equivalent to uranium oxide fuel. 30-50 per cent of the core may be composed of MOX-fuel without any effect on the operation and safety of the reactor which has been originally designed for uranium fuel. The evaluation of international fuel cycle (INFCE) states that the proliferation risks are very small. The recycling of plutonium will reduce demand for enriched uranium and the calculations show that 6.3 ton plutonium will replace the enrichment of 600 ton natural uranium. (G.B.)

  8. Evaluation of plutonium at Enewetak Atoll

    International Nuclear Information System (INIS)

    Wilson, D.W.; Ng, Y.C.; Robison, W.L.

    1975-01-01

    An extensive survey was carried out in 1972 to 1973 to assess the current radiological status of Enewetok Atoll. The radionuclides detected in the Atoll environment were studied for their potential contributions to the dose commitment of the returning population according to several pathways of exposure. Plutonium was detected in air and in the terrestrial and aquatic environment at concentrations that varied from background levels due to world-wide fallout to levels several orders-of-magnitude above. The dose commitments from plutonium via the terrestrial food chain and inhalation vary according to the postulated living pattern. The dosages via marine foods can be expected to be insensitive to living pattern and to exceed those via terrestrial foods. Plutonium would contribute nearly all of the dosage via inhalation, but this pathway ranks low in overall importance compared with the food-chain and external-dose pathways. Although the potential dose from plutonium via all pathways is low relative to that from 60 Co, 90 Sr and 137 Cs, plutonium will still remain in the Atoll environment after the other makor isotopes have decayed away. (author)

  9. Long-term plutonium storage: Design concepts

    International Nuclear Information System (INIS)

    Wilkey, D.D.; Wood, W.T.; Guenther, C.D.

    1994-01-01

    An important part of the Department of Energy (DOE) Weapons Complex Reconfiguration (WCR) Program is the development of facilities for long-term storage of plutonium. The WCR design goals are to provide storage for metals, oxides, pits, and fuel-grade plutonium, including material being held as part of the Strategic Reserve and excess material. Major activities associated with plutonium storage are sorting the plutonium inventory, material handling and storage support, shipping and receiving, and surveillance of material in storage for both safety evaluations and safeguards and security. A variety of methods for plutonium storage have been used, both within the DOE weapons complex and by external organizations. This paper discusses the advantages and disadvantages of proposed storage concepts based upon functional criteria. The concepts discussed include floor wells, vertical and horizontal sleeves, warehouse storage on vertical racks, and modular storage units. Issues/factors considered in determining a preferred design include operational efficiency, maintenance and repair, environmental impact, radiation and criticality safety, safeguards and security, heat removal, waste minimization, international inspection requirements, and construction and operational costs

  10. Solvent extraction process development for high plutonium fuel cycles

    Energy Technology Data Exchange (ETDEWEB)

    Anil Kumar, R; Selvaraj, P G; Natarajan, R; Raman, V R [Reprocessing Group, Indira Gandhi Centre for Atomic Research, Kalpakkam (India)

    1994-06-01

    The purification of high plutonium bearing irradiated fuels using 30% TBP in dodecane diluent requires precise determination of concentration profiles during steady state, transient and process upset conditions. Mathematical models have been developed and a computer code is in use for determining Pu-U concentration profiles in a solvent extraction equipment in a typical reprocessing plant. The process parameters have been optimised for recovery of U and Pu and decontamination from the fission products. This computer code is used to analyse the extraction flow sheets of fuels of two typical Pu-U compositions encountered in Indian fast breeder programme. The analysis include the effect of uncertainty in equilibrium condition prediction by the model and the variation of flows of streams during plant operation. The studies highlight the margin available to avoid second organic phase formation and adjustments required in the process flowsheet. (author). 7 refs., 7 figs., 2 tabs.

  11. Elaboration and characterisation of plutonium waste reference materials

    International Nuclear Information System (INIS)

    Perolat, J.P.

    1990-01-01

    The Analysis Methods Establishment Commission (CETAMA) has set up a program for the elaboration and characterisation of plutonium waste reference materials. The object of this program is to give laboratories the possibility to test and calibrate apparatus used in non-destructive methods for the analysis of plutonium waste. The different parameters of this program are presented: - characterisation of plutonium, - type and number of containers, - plutonium distribution inside the different containers, - description of the matrix

  12. PROCESS OF ELIMINATING HYDROGEN PEROXIDE IN SOLUTIONS CONTAINING PLUTONIUM VALUES

    Science.gov (United States)

    Barrick, J.G.; Fries, B.A.

    1960-09-27

    A procedure is given for peroxide precipitation processes for separating and recovering plutonium values contained in an aqueous solution. When plutonium peroxide is precipitated from an aqueous solution, the supernatant contains appreciable quantities of plutonium and peroxide. It is desirable to process this solution further to recover plutonium contained therein, but the presence of the peroxide introduces difficulties; residual hydrogen peroxide contained in the supernatant solution is eliminated by adding a nitrite or a sulfite to this solution.

  13. Accountability methods for plutonium and uranium: the NRC manuals

    Energy Technology Data Exchange (ETDEWEB)

    Gutmacher, R.G.; Stephens, F.B.

    1977-09-28

    Four manuals containing methods for the accountability of plutonium nitrate solutions, plutonium dioxide, uranium dioxide and mixed uranium-plutonium oxide have been prepared by us and issued by the U.S. Nuclear Regulatory Commission. A similar manual on methods for the accountability of uranium and plutonium in reprocessing plant dissolver solutions is now in preparation. In the present paper, we discuss the contents of the previously issued manuals and give a preview of the manual now being prepared.

  14. Accountability methods for plutonium and uranium: the NRC manuals

    International Nuclear Information System (INIS)

    Gutmacher, R.G.; Stephens, F.B.

    1977-01-01

    Four manuals containing methods for the accountability of plutonium nitrate solutions, plutonium dioxide, uranium dioxide and mixed uranium-plutonium oxide have been prepared by us and issued by the U.S. Nuclear Regulatory Commission. A similar manual on methods for the accountability of uranium and plutonium in reprocessing plant dissolver solutions is now in preparation. In the present paper, we discuss the contents of the previously issued manuals and give a preview of the manual now being prepared

  15. Monitoring of wastes containing plutonium. Necessity and method

    International Nuclear Information System (INIS)

    Sousselier, Y.; Pottier, P.

    1979-01-01

    Importance of problems set by wastes containing plutonium is rapidly growing. Plutonium is not a waste, recycling limits heavily the quantity of plutonium to be stored with wastes. Optimized waste management must take definitive storage and economical limits of plutonium recovery into account. Waste monitoring is a must for safety, economy and waste management. Methods used require reliability, simplicity, sensibility and accuracy particularly for threshold detection [fr

  16. Standard test method for plutonium assay by plutonium (III) diode array spectrophotometry

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2002-01-01

    1.1 This test method describes the determination of total plutonium as plutonium(III) in nitrate and chloride solutions. The technique is applicable to solutions of plutonium dioxide powders and pellets (Test Methods C 697), nuclear grade mixed oxides (Test Methods C 698), plutonium metal (Test Methods C 758), and plutonium nitrate solutions (Test Methods C 759). Solid samples are dissolved using the appropriate dissolution techniques described in Practice C 1168. The use of this technique for other plutonium-bearing materials has been reported (1-5), but final determination of applicability must be made by the user. The applicable concentration range for plutonium sample solutions is 10–200 g Pu/L. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropria...

  17. Fused salt processing of impure plutonium dioxide to high-purity plutonium metal

    International Nuclear Information System (INIS)

    Mullins, L.J.; Christensen, D.C.; Babcock, B.R.

    1982-01-01

    A process for converting impure plutonium dioxide (approx. 96% pure) to high-purity plutonium metal (>99.9%) was developed. The process consists of reducing the oxide to an impure plutonium metal intermediate with calcium metal in molten calcium chloride. The impure intermediate metal is cast into an anode and electrorefined to produce high-purity plutonium metal. The oxide reduction step is being done now on a 0.6-kg scale with the resulting yield being >99.5%. The electrorefining is being done on a 4.0-kg scale with the resulting yield being 80 to 85%. The purity of the product, which averages 99.98%, is essentially insensitive to the purity of the feed metal. The yield, however, is directly dependent on the chemical composition of the feed. To date, approximately 250 kg of impure oxide has been converted to pure metal by this processing sequence. The availability of impure plutonium dioxide, together with the need for pure plutonium metal, makes this sequence a valuable plutonium processing tool

  18. Effect of valence on the electromigration in silver

    International Nuclear Information System (INIS)

    Nguyen Van Doan

    1970-01-01

    It is shown that the apparent effective valence Z B ** of a solute deduced from experiments differs from the true effective valence Z B * defined in the atomic models by a corrective term due to the 'vacancy flow effect'. The experimental results suggest that this corrective term is very important and that it is negative for transition elements; this hypothesis is confirmed for the case of iron in a copper matrix. For the elements to the right of silver in the periodic table, where the correction can be neglected, the effective valence of the solute varies linearly with z (z + 1), z being the difference between the valency of the solute and the solvent; in contrast, the further the solute is from the solvent in the periodic table the more nearly the electronic structure of the ion at the saddle point resembles that of the ion at the equilibrium position. (author) [fr

  19. Hole energy and momentum distributions in valence bands

    International Nuclear Information System (INIS)

    Laan, G. van der.

    1982-01-01

    In order to understand the electrical and magnetic properties of solids, the knowledge of the density of states and the dispersion relation of the valence bands is indispensable. This thesis offers some alternative methods to obtain information about the nature of the valence band. Part A deals with the energy distribution of the photoelectrons. A simple model, which explains the core hole satellite structure in compounds with large correlation effects between the valence band holes and the created photo-hole, is outlined. CuCl, CuX 2 (X = F Cl and Br) are studied, by photoemission and Auger electron spectroscopies in determining the valence band properties. Part B deals with the simultaneous measurement of the energy and the wave vector of the emitted electrons. A practical example is given for the determination of the dispersion relation in copper. The measurements of a surface resonance band and the distribution of the secondary electrons are also reported. (Auth.)

  20. Aqueous Chloride Operations Overview: Plutonium and Americium Purification/Recovery

    Energy Technology Data Exchange (ETDEWEB)

    Kimball, David Bryan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Skidmore, Bradley Evan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-06-22

    Acqueous Chloride mission is to recover plutonium and americium from pyrochemical residues (undesirable form for utilization and storage) and generate plutonium oxide and americium oxide. Plutonium oxide is recycled into Pu metal production flowsheet. It is suitable for storage. Americium oxide is a valuable product, sold through the DOE-OS isotope sales program.

  1. Metal plutonium conversion to components of nuclear reactor fuel

    International Nuclear Information System (INIS)

    Subbotin, V.G.; Panov, A.V.; Mashirev, V.P.

    2000-01-01

    Capabilities of different technologies for plutonium conversion to the fuel components of nuclear reactors are studied. Advantages and shortcomings of aqueous and nonaqueous methods of plutonium treatment are shown. Proposals to combine and coordinate efforts of world scientific and technological community in solving problems concerning plutonium of energetic and weapon origin treatment were put forward. (authors)

  2. Metal plutonium conversion to components of nuclear reactor fuel

    Energy Technology Data Exchange (ETDEWEB)

    Subbotin, V.G.; Panov, A.V. [Russian Federal Nuclear Center, ALL-Russian Science and Research, Institute of Technical Physics, Snezhinsk (Russian Federation); Mashirev, V.P. [ALL-Russian Science and Research Institute of Chemical Technology, Moscow (Russian Federation)

    2000-07-01

    Capabilities of different technologies for plutonium conversion to the fuel components of nuclear reactors are studied. Advantages and shortcomings of aqueous and nonaqueous methods of plutonium treatment are shown. Proposals to combine and coordinate efforts of world scientific and technological community in solving problems concerning plutonium of energetic and weapon origin treatment were put forward. (authors)

  3. Precipitation of plutonium from acidic solutions using magnesium oxide

    International Nuclear Information System (INIS)

    Jones, S.A.

    1994-01-01

    Magnesium oxide will be used as a neutralizing agent for acidic plutonium-containing solutions. It is expected that as the magnesium oxide dissolves, the pH of the solution will rise, and plutonium will precipitate. The resulting solid will be tested for suitability to storage. The liquid is expected to contain plutonium levels that meet disposal limit requirements

  4. Response to suspected or known intakes of plutonium (Draft)

    International Nuclear Information System (INIS)

    Heid, K.R.

    1983-04-01

    The techniques used at Hanford for routine surveillance, incident detection and prompt assessment of a plutonium intake are reviewed. The techniques described are based on experience from some 80,000 man-years of plutonium work at Hanford which included a variety of manufacturing and R and D programs and involved several isotopes and chemical forms of plutonium

  5. Modulation of motor-meaning congruity effects for valenced words

    OpenAIRE

    Brookshire, Geoffrey; Ivry, Richard; Casasanto, Daniel

    2010-01-01

    We investigated the extent to which emotionally valenced words automatically cue spatio-motor representations. Participants made speeded button presses, moving their hand upward or downward while viewing words with positive or negative valence. Only the color of the words was relevant to the response; on target trials, there was no requirement to read the words or process their meaning. In Experiment 1, upward responses were faster for positive words, and downward for negative words. This eff...

  6. The future of plutonium - an overview

    International Nuclear Information System (INIS)

    Larson, C.E.

    1975-01-01

    Plutonium is the underpinning of the nuclear industry. Without it it is estimated that the fuel will run out not long after the turn of the century. With plutonium in fast breeders nuclear reactors can be operated for tens of thousands of years and the depleted uranium now available can be utilized The fuel cycle contemplated is similar to that of the light water reactor with some important differences at least partially related to the greater radioactivity of the resulting mixture of plutonium isotopes. The regulatory program does recognize the problems, including those of toxicity, safeguards and transportation. The concept of an integrated fuel cycle facility at a single location must be seriously considered. (author)

  7. The veining phenomenon in unalloyed plutonium

    International Nuclear Information System (INIS)

    White, J.S.

    1976-01-01

    An investigation has been made of the veining phenomenon in unalloyed plutonium. The surface markings, or veins, which are sometimes seen on α-phase plutonium samples, arise as a result of the β→α transformation. As far as is known, this veining is unrivalled in its scale and form as compared with the solid state surface transformation effects shown by any other metal. The phenomenon has been explained by the application of the Le Chatelier principle to the phase change. In this instance, the large (10%) volume contraction associated with the β→α reaction and the anisotropy of the nonoclinic α-phase structure, account for the fact that the veins are so prominent in plutonium. On the basis of the proposed model, the veins can only form at temperatures where the transformation mechanism is non-martensitic. (Auth.)

  8. Review of major plutonium pyrochemical technology

    International Nuclear Information System (INIS)

    Moser, W.S.; Navratil, J.D.

    1983-01-01

    The past twenty years have seen significant growth in the development and application of pyrochemical technology for processing of plutonium. For particular feedstocks and specific applications, non-aqueous high-temperature processes offer key advantages over conventional hydrometallurgical systems. Major processes in use today include: (1) direct oxide reduction for conversion of PuO 2 to metal, (2) molten salt extraction for americium removal from plutonium, (3) molten salt electrorefining for Pu purification, and (4) hydriding to remove plutonium from host substrates. This paper reviews current major pyrochemical processes from the classical calcination-hydrofluorination-bomb reduction sequence through new techniques under development. Each process is presented and brief descriptions of production equipment are given. 47 references, 5 figures

  9. Pathology associated with inhaled plutonium in beagles

    International Nuclear Information System (INIS)

    Dagle, G.E.; Park, J.F.; Weller, R.E.; Ragan, H.A.; Stevens, D.L.

    1986-01-01

    The pathology associated with the inhalation of plutonium was studied in beagle dogs given a single exposure to aerosols of 239 PuO 2 , 238 PuO 2 , or 239 Pu(NO 3 ) 4 . The temporal-spatial relationships between plutonium deposition and the development of lesions in dogs were evaluated up to 11 years, 8 years, or 5 years, respectively, after exposures, resulting in initial lung burdens ranging from ∼2 to ∼5500 nCi. Exposure of the lung to high dose levels produced a spectrum of progressively more severe morphological changes, ranging from radiation pneumonitis to fibrosis. Lung tumors occurred at exposure levels that did not result in early death from radiation pneumonitis or fibrosis. Bronchiolar-alveolar carcinomas, papillary adenocarcinomas, epidermoid carcinomas, and combined epidermoid and adenocarcinomas were observed. Sclerosing tracheobronchial lymphadenitis, radiation osteodystrophy, osteosarcoma, and hepatic adenomatous hyperplasia were the principal extrapulmonary lesions resulting from translocation of plutonium. 15 refs., 2 tabs

  10. Excess plutonium disposition using ALWR technology

    International Nuclear Information System (INIS)

    Phillips, A.; Buckner, M.R.; Radder, J.A.; Angelos, J.G.; Inhaber, H.

    1993-02-01

    The Office of Nuclear Energy of the Department of Energy chartered the Plutonium Disposition Task Force in August 1992. The Task Force was created to assess the range of practicable means of disposition of excess weapons-grade plutonium. Within the Task Force, working groups were formed to consider: (1) storage, (2) disposal,and(3) fission options for this disposition,and a separate group to evaluate nonproliferation concerns of each of the alternatives. As a member of the Fission Working Group, the Savannah River Technology Center acted as a sponsor for light water reactor (LWR) technology. The information contained in this report details the submittal that was made to the Fission Working Group of the technical assessment of LWR technology for plutonium disposition. The following aspects were considered: (1) proliferation issues, (2) technical feasibility, (3) technical availability, (4) economics, (5) regulatory issues, and (6) political acceptance

  11. Excess plutonium disposition: The deep borehole option

    International Nuclear Information System (INIS)

    Ferguson, K.L.

    1994-01-01

    This report reviews the current status of technologies required for the disposition of plutonium in Very Deep Holes (VDH). It is in response to a recent National Academy of Sciences (NAS) report which addressed the management of excess weapons plutonium and recommended three approaches to the ultimate disposition of excess plutonium: (1) fabrication and use as a fuel in existing or modified reactors in a once-through cycle, (2) vitrification with high-level radioactive waste for repository disposition, (3) burial in deep boreholes. As indicated in the NAS report, substantial effort would be required to address the broad range of issues related to deep bore-hole emplacement. Subjects reviewed in this report include geology and hydrology, design and engineering, safety and licensing, policy decisions that can impact the viability of the concept, and applicable international programs. Key technical areas that would require attention should decisions be made to further develop the borehole emplacement option are identified

  12. Review Of Plutonium Oxidation Literature

    International Nuclear Information System (INIS)

    Korinko, P.

    2009-01-01

    A brief review of plutonium oxidation literature was conducted. The purpose of the review was to ascertain the effect of oxidation conditions on oxide morphology to support the design and operation of the PDCF direct metal oxidation (DMO) furnace. The interest in the review was due to a new furnace design that resulted in oxide characteristics that are different than those of the original furnace. Very little of the published literature is directly relevant to the DMO furnace operation, which makes assimilation of the literature data with operating conditions and data a convoluted task. The oxidation behavior can be distilled into three regimes, a low temperature regime (RT to 350 C) with a relatively slow oxidation rate that is influenced by moisture, a moderate temperature regime (350-450 C) that is temperature dependent and relies on more or less conventional oxidation growth of a partially protective oxide scale, and high temperature oxidation (> 500 C) where the metal autocatalytically combusts and oxidizes. The particle sizes obtained from these three regimes vary with the finest being from the lowest temperature. It is surmised that the slow growth rate permits significant stress levels to be achieved that help break up the oxides. The intermediate temperatures result in a fairly compact scale that is partially protective and that grows to critical thickness prior to fracturing. The growth rate in this regime may be parabolic or paralinear, depending on the oxidation time and consequently the oxide thickness. The high temperature oxidation is invariant in quiescent or nearly quiescent conditions due to gas blanketing while it accelerates with temperature under flowing conditions. The oxide morphology will generally consist of fine particles ( 250 (micro)m). The particle size ratio is expected to be < 5%, 25%, and 70% for fine, medium and large particles, respectively, for metal temperatures in the 500-600 C range.

  13. Feedback-related negativity codes outcome valence, but not outcome expectancy, during reversal learning.

    Science.gov (United States)

    von Borries, A K L; Verkes, R J; Bulten, B H; Cools, R; de Bruijn, E R A

    2013-12-01

    Optimal behavior depends on the ability to assess the predictive value of events and to adjust behavior accordingly. Outcome processing can be studied by using its electrophysiological signatures--that is, the feedback-related negativity (FRN) and the P300. A prominent reinforcement-learning model predicts an FRN on negative prediction errors, as well as implying a role for the FRN in learning and the adaptation of behavior. However, these predictions have recently been challenged. Notably, studies so far have used tasks in which the outcomes have been contingent on the response. In these paradigms, the need to adapt behavioral responses is present only for negative, not for positive feedback. The goal of the present study was to investigate the effects of positive as well as negative violations of expectancy on FRN amplitudes, without the usual confound of behavioral adjustments. A reversal-learning task was employed in which outcome value and outcome expectancy were orthogonalized; that is, both positive and negative outcomes were equally unexpected. The results revealed a double dissociation, with effects of valence but not expectancy on the FRN and, conversely, effects of expectancy but not valence on the P300. While FRN amplitudes were largest for negative-outcome trials, irrespective of outcome expectancy, P300 amplitudes were largest for unexpected-outcome trials, irrespective of outcome valence. These FRN effects were interpreted to reflect an evaluation along a good-bad dimension, rather than reflecting a negative prediction error or a role in behavioral adaptation. By contrast, the P300 reflects the updating of information relevant for behavior in a changing context.

  14. Search for plutonium salt deposits in the plutonium extraction batteries of the Marcoule plant (1963)

    International Nuclear Information System (INIS)

    Bouzigues, H.; Reneaud, J.M.

    1963-01-01

    This report describes a method and a special apparatus making it possible to detach the insoluble plutonium salt deposits in the extraction chain of an irradiated fuel treatment plant. The process chosen allows the detection, in the extraction batteries or in the highly active chemical engineering equipment, of plutonium quantities of a few grains. After four years operation it has been impossible to detect measurable quantities of plutonium in any part of the extraction chain. The results have been confirmed by visual examinations carried out with a specially constructed endoscope. (authors) [fr

  15. Explaining the effect of event valence on unrealistic optimism.

    Science.gov (United States)

    Gold, Ron S; Brown, Mark G

    2009-05-01

    People typically exhibit 'unrealistic optimism' (UO): they believe they have a lower chance of experiencing negative events and a higher chance of experiencing positive events than does the average person. UO has been found to be greater for negative than positive events. This 'valence effect' has been explained in terms of motivational processes. An alternative explanation is provided by the 'numerosity model', which views the valence effect simply as a by-product of a tendency for likelihood estimates pertaining to the average member of a group to increase with the size of the group. Predictions made by the numerosity model were tested in two studies. In each, UO for a single event was assessed. In Study 1 (n = 115 students), valence was manipulated by framing the event either negatively or positively, and participants estimated their own likelihood and that of the average student at their university. In Study 2 (n = 139 students), valence was again manipulated and participants again estimated their own likelihood; additionally, group size was manipulated by having participants estimate the likelihood of the average student in a small, medium-sized, or large group. In each study, the valence effect was found, but was due to an effect on estimates of own likelihood, not the average person's likelihood. In Study 2, valence did not interact with group size. The findings contradict the numerosity model, but are in accord with the motivational explanation. Implications for health education are discussed.

  16. Valence, arousal and cognitive control: A voluntary task switching study

    Directory of Open Access Journals (Sweden)

    Jelle eDemanet

    2011-11-01

    Full Text Available The present study focused on the interplay between arousal, valence and cognitive control. To this end, we investigated how arousal and valence associated with affective stimuli influenced cognitive flexibility when switching between tasks voluntarily. Three hypotheses were tested. First, a valence hypothesis that states that the positive valence of affective stimuli will facilitate both global and task-switching performance because of increased cognitive flexibility. Second, an arousal hypothesis that states that arousal, and not valence, will specifically impair task-switching performance by strengthening the previously executed task-set. Third, an attention hypothesis that states that both cognitive and emotional control ask for limited attentional resources, and predicts that arousal will impair both global and task-switching performance. The results showed that arousal affected task-switching but not global performance, possibly by phasic modulations of the noradrenergic system that reinforces the previously executed task. In addition, positive valence only affected global performance but not task-switching performance, possibly by phasic modulations of dopamine that stimulates the general ability to perform in a multitasking environment.

  17. Emotional valence and the free-energy principle.

    Science.gov (United States)

    Joffily, Mateus; Coricelli, Giorgio

    2013-01-01

    The free-energy principle has recently been proposed as a unified Bayesian account of perception, learning and action. Despite the inextricable link between emotion and cognition, emotion has not yet been formulated under this framework. A core concept that permeates many perspectives on emotion is valence, which broadly refers to the positive and negative character of emotion or some of its aspects. In the present paper, we propose a definition of emotional valence in terms of the negative rate of change of free-energy over time. If the second time-derivative of free-energy is taken into account, the dynamics of basic forms of emotion such as happiness, unhappiness, hope, fear, disappointment and relief can be explained. In this formulation, an important function of emotional valence turns out to regulate the learning rate of the causes of sensory inputs. When sensations increasingly violate the agent's expectations, valence is negative and increases the learning rate. Conversely, when sensations increasingly fulfil the agent's expectations, valence is positive and decreases the learning rate. This dynamic interaction between emotional valence and learning rate highlights the crucial role played by emotions in biological agents' adaptation to unexpected changes in their world.

  18. Emotional valence and the free-energy principle.

    Directory of Open Access Journals (Sweden)

    Mateus Joffily

    Full Text Available The free-energy principle has recently been proposed as a unified Bayesian account of perception, learning and action. Despite the inextricable link between emotion and cognition, emotion has not yet been formulated under this framework. A core concept that permeates many perspectives on emotion is valence, which broadly refers to the positive and negative character of emotion or some of its aspects. In the present paper, we propose a definition of emotional valence in terms of the negative rate of change of free-energy over time. If the second time-derivative of free-energy is taken into account, the dynamics of basic forms of emotion such as happiness, unhappiness, hope, fear, disappointment and relief can be explained. In this formulation, an important function of emotional valence turns out to regulate the learning rate of the causes of sensory inputs. When sensations increasingly violate the agent's expectations, valence is negative and increases the learning rate. Conversely, when sensations increasingly fulfil the agent's expectations, valence is positive and decreases the learning rate. This dynamic interaction between emotional valence and learning rate highlights the crucial role played by emotions in biological agents' adaptation to unexpected changes in their world.

  19. Lung, liver and bone cancer mortality after plutonium exposure in beagle dogs and nuclear workers.

    Science.gov (United States)

    Wilson, Dulaney A; Mohr, Lawrence C; Frey, G Donald; Lackland, Daniel; Hoel, David G

    2010-01-01

    The Mayak Production Association (MPA) worker registry has shown evidence of plutonium-induced health effects. Workers were potentially exposed to plutonium nitrate [(239)Pu(NO(3))(4)] and plutonium dioxide ((239)PuO(2)). Studies of plutonium-induced health effects in animal models can complement human studies by providing more specific data than is possible in human observational studies. Lung, liver, and bone cancer mortality rate ratios in the MPA worker cohort were compared to those seen in beagle dogs, and models of the excess relative risk of lung, liver, and bone cancer mortality from the MPA worker cohort were applied to data from life-span studies of beagle dogs. The lung cancer mortality rate ratios in beagle dogs are similar to those seen in the MPA worker cohort. At cumulative doses less than 3 Gy, the liver cancer mortality rate ratios in the MPA worker cohort are statistically similar to those in beagle dogs. Bone cancer mortality only occurred in MPA workers with doses over 10 Gy. In dogs given (239)Pu, the adjusted excess relative risk of lung cancer mortality per Gy was 1.32 (95% CI 0.56-3.22). The liver cancer mortality adjusted excess relative risk per Gy was 55.3 (95% CI 23.0-133.1). The adjusted excess relative risk of bone cancer mortality per Gy(2) was 1,482 (95% CI 566.0-5686). Models of lung cancer mortality based on MPA worker data with additional covariates adequately described the beagle dog data, while the liver and bone cancer models were less successful.

  20. Plutonium production in a remote cell

    International Nuclear Information System (INIS)

    Maddux, E.P.; Purcell, J.A.

    1987-01-01

    Production of 239 Pu metal has traditionally been carried out in glovebox enclosures for protection of operating personnel and the environment. With the advent of more stringent federal regulations for protecting personnel, the environment, and security of special nuclear materials, it is proposed that plutonium be processed in a totally remote environment using automated work stations and robotic materials transfer and equipment maintenance. At the Savannah River Plant, the existing plutonium production facility is a batch-type glovebox operation built in the 1950s. A viable alternative to restoration of the existing glovebox operation is to provide a facility that uses remote cell operation

  1. Repository and deep borehole disposition of plutonium

    International Nuclear Information System (INIS)

    Halsey, W.G.

    1996-02-01

    Control and disposition of excess weapons plutonium is a growing issue as both the US and Russia retire a large number of nuclear weapons> A variety of options are under consideration to ultimately dispose of this material. Permanent disposition includes tow broad categories: direct Pu disposal where the material is considered waste and disposed of, and Pu utilization, where the potential energy content of the material is exploited via fissioning. The primary alternative to a high-level radioactive waste repository for the ultimate disposal of plutonium is development of a custom geologic facility. A variety of geologic facility types have been considered, but the concept currently being assessed is the deep borehole

  2. Skeletal lesions from inhaled plutonium in beagles

    International Nuclear Information System (INIS)

    Dagle, G.E.; Park, J.F.; Weller, R.E.; Ragan, H.A.; McClanahan, B.J.; Fisher, D.R.

    1984-10-01

    The report briefly reviews the skeletal effects observed in ongoing lifespan studies in beagle dogs at 13, 10, and 7 years, respectively, after inhalation exposure to 239 Pu oxide and nitrate or 238 Pu oxide. Plutonium nitrate was chosen to represent soluble material more readily translocated to bone and other tissues than the oxide. Bone lesions related to plutonium exposure were observed only in dogs exposed to 238 Pu oxide and 239 Pu nitrate. The skeleton accumulated approximately 2% ( 239 Pu oxide), 45% ( 238 Pu oxide) or 50% ( 239 Pu nitrate) of the final body burdens at 13, 10, and 7 years, respectively, after exposure. 11 references, 2 figures

  3. Plutonium Contaminated Materials Working Party development programme

    International Nuclear Information System (INIS)

    Higson, S.G.

    1985-01-01

    The broad objectives of the programme are to develop and assess: (a) techniques for the minimisation, treatment and encapsulation of solid PCM; (b) techniques for the measurement of plutonium in encapsulated and unencapsulated PCM; and (c) advanced treatments for alpha bearing liquid wastes, in order to provide information on their waste management implications. Development has been carried out in eight areas: (a) reduction of arisings; (b) plutonium measurement; (c) decommissioning and non-combustible PCM treatments; (d) washing; (e) PCM immobilisation; (f) liquid effluent treatment; (g) sorting and packaging; and (h) engineering objectives. The work is reported. (author)

  4. Beating swords into plowshares. [Surplus plutonium

    Energy Technology Data Exchange (ETDEWEB)

    Anon.

    With the end of the Cold War and the consequent dismantling of United States and Russian nuclear weapons, comes the problem of what to do with the plutonium and highly enriched uranium thus produced. This surplus fissile material could pose a national and international security hazard and recent studies have stresses the need for mutual and cooperative monitoring of fissile material stocks. Long term proposals for disposal, such as burning the plutonium in nuclear plants, vitrifying it into high-level waste glass logs and burying it in deep boreholes in the Earth's surface are all considered with respect to safety and economic viability. (UK).

  5. Beating plutonium swords into electrical plowshares

    International Nuclear Information System (INIS)

    Ofte, D.

    1993-01-01

    After decades of producing large quantities of weapons-grade plutonium, the United States and the Confederation of Independent States are faced with an unanticipated dilemma of a growing surplus of that material. This circumstance could not have been anticipated just a few years ago after living with a weapons program that from its inception in the United States was characterized by a chronic tight supply situation. The rapid drawdown of the nuclear weapons stockpile presents a near-term problem of storage capacity in the system until the United States makes a disposition decision for what may be in excess of 50 tonnes of weapons-grade plutonium

  6. Modeling the thermodynamic properties of plutonium

    International Nuclear Information System (INIS)

    Stan, Marius

    2000-01-01

    The golden dream of any modeling enterprise is to predict the properties of the studied system in a new and often 'hostile' environment. The basis of this kind of work is the careful, accurate assessment of the system properties in normal conditions. What 'normal conditions' means for plutonium is an interesting question itself. This work is dedicated to modeling only a fraction of the remarkable characteristics of this 'mysterious' material, that is the thermodynamic properties of its six allotropic phases (seven under pressure), the liquid phase, and the vapor phase. The goal is to provide valuable information for the calculation of alloyed plutonium phase diagrams

  7. A Plutonium Ceramic Target for MASHA

    International Nuclear Information System (INIS)

    Wilk, P A; Shaughnessy, D A; Moody, K J; Kenneally, J M; Wild, J F; Stoyer, M A; Patin, J B; Lougheed, R W; Ebbinghaus, B B; Landingham, R L; Oganessian, Y T; Yeremin, A V; Dmitriev, S N

    2004-01-01

    We are currently developing a plutonium ceramic target for the MASHA mass separator. The MASHA separator will use a thick plutonium ceramic target capable of tolerating temperatures up to 2000 C. Promising candidates for the target include oxides and carbides, although more research into their thermodynamic properties will be required. Reaction products will diffuse out of the target into an ion source, where they will then be transported through the separator to a position-sensitive focal-plane detector array. Experiments on MASHA will allow us to make measurements that will cement our identification of element 114 and provide for future experiments where the chemical properties of the heaviest elements are studied

  8. Separation of plutonium oxide nanoparticles and colloids

    Energy Technology Data Exchange (ETDEWEB)

    Wilson, Richard E.; Skanthakumar, S.; Soderholm, L. [Argonne National Laboratory, IL (United States). Chemical Sciences and Engineering Division

    2011-11-18

    Colloidal plutonium is an important component of Pu aqueous speciation. Pu colloids are problematic in nuclear separations and are a potential transport vector in the environment. Using a mixture of n-octanol and trichloroacetic acid a selective and reversible separation of these particles can be achieved by exploiting their surface reactivity. [German] Kolloidales Plutonium ist ein wichtiger Bestandteil in waessrigen Pu-Bereitungen. Pu-Kolloide sind problematisch bei der Wiederaufbereitung von Kernmaterial und bilden einen potenziellen Transportvektor in die Umwelt. Mit einem Loesungsmittelgemisch aus n-Octanol und Trichloressigsaeure gelingt die selektive und reversible Trennung dieser Partikel durch Ausnutzung ihrer Oberflaechenreaktivitaet.

  9. Automatic titrator for high precision plutonium assay

    International Nuclear Information System (INIS)

    Jackson, D.D.; Hollen, R.M.

    1986-01-01

    Highly precise assay of plutonium metal is required for accountability measurements. We have developed an automatic titrator for this determination which eliminates analyst bias and requires much less analyst time. The analyst is only required to enter sample data and start the titration. The automated instrument titrates the sample, locates the end point, and outputs the results as a paper tape printout. Precision of the titration is less than 0.03% relative standard deviation for a single determination at the 250-mg plutonium level. The titration time is less than 5 min

  10. Preconcentration of plutonium radionuclides from natural waters

    International Nuclear Information System (INIS)

    Wong, K.M.; Nioshkin, V.E.; Jokela, T.A.

    1978-02-01

    A large volume water sampler using manganese dioxide impregnated cartridges for the in situ separation of plutonium in sea water and ground water was studied. Plutonium concentrations obtained by this technique are compared with a radiochemical coprecipitation method. Consistent results were obtained between the two methods for water samples from the Pacific Ocean and Enewetak lagoon. Different results were noted from samples collected in the Enewetak reef and ground water stations. Using this preconcentration technique and the coprecipitation method it was shown that the physical-chemical characteristics of Pu in Enewetak reef and ground water are different from the lagoon and open ocean

  11. Plutonium challenges. Changing dimensions of global cooperation

    International Nuclear Information System (INIS)

    Oi, Noboru

    1998-01-01

    Global developoments in the 1990s have presented the international community with a new and serious challenge: a growing accumulation of plutonium originating from both civilian and military nuclear programmes. It arises from a number of developments. In this article, selected aspects of the issue of plutonium management in civilian nuclear programmes are discussed over a longer term perspective in the context of global cooperation and the IAEA's own role, which is evolving in response to the interests of its Member States. It draws upon discussions at international fora, including the International Symposium on Nuclear Fuel Cycle and Reactor Strategies in Jun 1997

  12. Diffusion in the uranium - plutonium system and self-diffusion of plutonium in epsilon phase; Diffusion dans le systeme uranium-plutonium et autodiffusion du plutonium epsilon

    Energy Technology Data Exchange (ETDEWEB)

    Dupuy, M [Commissariat a l' Energie Atomique, Fontenay-Aux-Roses (France). Centre d' Etudes Nucleaires

    1967-07-01

    A survey of uranium-plutonium phase diagram leads to confirm anglo-saxon results about the plutonium solubility in {alpha} uranium (15 per cent at 565 C) and the uranium one in {zeta} phase (74 per cent at 565 C). Interdiffusion coefficients, for concentration lower than 15 per cent had been determined in a temperature range from 410 C to 640 C. They vary between 0.2 and 6 10{sup 12} cm{sup 2} s{sup -1}, and the activation energy between 13 and 20 kcal/mole. Grain boundary, diffusion of plutonium in a uranium had been pointed out by micrography, X-ray microanalysis and {alpha} autoradiography. Self-diffusion of plutonium in {epsilon} phase (bcc) obeys Arrhenius law: D = 2. 10{sup -2} exp -(18500)/RT. But this activation energy does not follow empirical laws generally accepted for other metals. It has analogies with 'anomalous' bcc metals ({beta}Zr, {beta}Ti, {beta}Hf, U{sub {gamma}}). (author) [French] Une etude du diagramme d'equilibre uranium-plutonium conduit a confirmer les resultats anglo-saxons relatifs a la solubilite du plutonium dans l'uranium {alpha} (15 pour cent a 565 C) et de l'uranium dans la phase {zeta} (74 pour cent a 565 C). Les coefficients de diffusion chimique, pour des concentrations inferieures a 15 pour cent ont ete determines a des temperatures comprises entre 410 et 640 C. Ils se situent entre 0.2 et 6. 10{sup 12} cm{sup 2} s{sup -1}. L'energie d'activation varie entre 13 et 20 kcal/mole. La diffusion intergranulaire du plutonium dans l'uranium a a ete mise en evidence par micrographie, microanalyse X et autoradiographie {alpha}. L' autodiffusion du plutonium {beta} cubique centree obeit a la loi d'Arrhenius D = 2. 10{sup -2} exp - (18500)/RT. Son energie d'activation n'obeit pas aux lois empiriques generalement admises pour les autres metaux. Elle possede des analogies avec les cubiques centres ''anormaux'' (Zr{beta}, Ti{beta}, Hf{beta}, U{gamma}). (auteur)

  13. Improvements in the detection of airborne plutonium

    International Nuclear Information System (INIS)

    Ryden, D.J.

    1981-02-01

    It is shown how it is possible to compensate individually for each of the background components on the filter paper used to collect samples. Experimentally it has been shown that the resulting compensated background count-rate averages zero with a standard deviation very close to the fundamental limit set by random statistical variations. Considerable improvements in the sensitivity of detecting airborne plutonium have been achieved. Two new plutonium-in-air monitors which use the compensation schemes described in this report are now available. Both have operated successfully in high concentrations of radon daughters. (author)

  14. Color center formation in plutonium electrorefining residues

    International Nuclear Information System (INIS)

    Morris, D.E.; Eller, P.G.; Hobart, D.E.; Eastman, M.P.; McCurry, L.E.

    1989-01-01

    Plutonium electrorefining residues containing Pu(III) in KCl exhibit dramatic reversible, light-induced color changes. Similar color changes were observed in Ln-doped (Ln = La, Nd, Gd, and Lu) and undoped KCl samples which were subjected to intense gamma irradiation. Diffuse reflectance electronic and electron paramagnetic resonance spectroscopies were used to show conclusively that Pu(III) is present in both the bleached and unbleached plutonium-bearing residues and the spectacular color changes are the result of color center formation and alternation by visible light. (orig.)

  15. Closure Welding of Plutonium Bearing Storage Containers

    International Nuclear Information System (INIS)

    Cannell, G.R.

    2002-01-01

    A key element in the Department of Energy (DOE) strategy for the stabilization, packaging and storage of plutonium-bearing materials involves closure welding of DOE-STD-3013 Outer Containers (3013 container). The 3013 container provides the primary barrier and pressure boundary preventing release of plutonium-bearing materials to the environment. The final closure (closure weld) of the 3013 container must be leaktight, structurally sound and meet DOE STD 3013 specified criteria. This paper focuses on the development, qualification and demonstration of the welding process for the closure welding of Hanford PFP 3013 outer containers

  16. Measurement of Plutonium Isotopic Composition - MGA

    Energy Technology Data Exchange (ETDEWEB)

    Vo, Duc Ta [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2015-08-21

    In this module, we will use the Canberra InSpector-2000 Multichannel Analyzer with a high-purity germanium detector (HPGe) and the MGA isotopic anlysis software to assay a variety of plutonium samples. The module provides an understanding of the MGA method, its attributes and limitations. You will assess the system performance by measuring a range of materials similar to those you may assay in your work. During the final verification exercise, the results from MGA will be combined with the 240Pueff results from neutron coincidence or multiplicity counters so that measurements of the plutonium mass can be compared with the operator-declared (certified) values.

  17. Interference from radon-thoron daughters in plutonium channel of a continuous plutonium-in-air monitor

    International Nuclear Information System (INIS)

    Pendharkar, K.A.; Krishnamony, S.

    1983-01-01

    This paper summarises the results of a study conducted to define the extent of interference from the daughter products of radon/thoron to the plutonium channel of a continuous plutonium-in-air monitor. The effect on the detection limits of the instrument due to chemical form (transportable or non-transportable) and isotopic composition of plutonium aerosol are briefly discussed. (author)

  18. Modeling of Diffusion of Plutonium in Other Metals and of Gaseous Species in Plutonium-Based Systems

    International Nuclear Information System (INIS)

    Cooper, Bernard R.; Gayanath W. Fernando; Beiden, S.; Setty, A.; Sevilla, E.H.

    2004-01-01

    Establish standards for temperature conditions under which plutonium, uranium, or neptunium from nuclear wastes permeates steel, with which it is in contact, by diffusion processes. The primary focus is on plutonium because of the greater difficulties created by the peculiarities of face-centered-cubic-stabilized (delta) plutonium (the form used in the technology generating the waste)

  19. Determination of mixture valence plutonium and multicomponent by computer resolution analysis of absorption spectrum (UV/VIS/NIR) (CRAAS)

    International Nuclear Information System (INIS)

    Zhuang Weixin; Ye Guoan; Huang Lifeng; Sun Hongfang; Zhao Yanju

    1996-09-01

    A spectrophotometry has been developed which can directly determine a multi-component sample by spectrophotometry without any chemical separation. CRAAS (Computer Resolution Analysis of Absorption Spectrum) has been reported. It is different from the previous spectrophotometry depending on only one or several special absorption peak. The CRAAS deals with the whole region of absorption spectrum by mathematical statistics. So CRAAS has higher accuracy, stronger power and very high resolution. The trouble comes from overlap of different spectrum in each other has been solved because CRAAS depends on the whole spectrum. As long as two spectra have different shape, their concentrations can be determined even their special absorption peaks are seriously overlapped. The accuracy is about +-5%. (2 refs., 7 figs., 8 tabs.)

  20. Plutonium-uranium mixed oxide characterization by coupling micro-X-ray diffraction and absorption investigations

    Science.gov (United States)

    Degueldre, C.; Martin, M.; Kuri, G.; Grolimund, D.; Borca, C.

    2011-09-01

    Plutonium-uranium mixed oxide (MOX) fuels are currently used in nuclear reactors. The potential differences of metal redox state and microstructural developments of the matrix before and after irradiation are commonly analysed by electron probe microanalysis. In this work the structure and next-neighbor atomic environments of Pu and U oxide features within unirradiated homogeneous MOX and irradiated (60 MW d kg -1) MOX samples was analysed by micro-X-ray fluorescence (μ-XRF), micro-X-ray diffraction (μ-XRD) and micro-X-ray absorption fine structure (μ-XAFS) spectroscopy. The grain properties, chemical bonding, valences and stoichiometry of Pu and U are determined from the experimental data gained for the unirradiated as well as for irradiated fuel material examined in the center of the fuel as well as in its peripheral zone (rim). The formation of sub-grains is observed as well as their development from the center to the rim (polygonization). In the irradiated sample Pu remains tetravalent (>95%) and no (oxidation in the rim zone. Any slight potential plutonium oxidation is buffered by the uranium dioxide matrix while locally fuel cladding interaction could also affect the redox of the fuel.

  1. Surplus plutonium disposition draft environmental impact statement. Volume 2

    International Nuclear Information System (INIS)

    1998-07-01

    On May 22, 1997, DOE published a Notice of Intent (NOI) in the Federal Register (62 Federal Register 28009) announcing its decision to prepare an environmental impact statement (EIS) that would tier from the analysis and decisions reached in connection with the Storage and Disposition of Weapons-Usable Fissile Materials Final Programmatic EIS (Storage and Disposition PEIS). DOE's disposition strategy allows for both the immobilization of surplus plutonium and its use as mixed oxide (MOX) fuel in existing domestic, commercial reactors. The disposition of surplus plutonium would also involve disposal of the immobilized plutonium and MOX fuel (as spent nuclear fuel) in a geologic repository. The Surplus Plutonium Disposition Environmental Impact Statement analyzes alternatives that would use the immobilization approach (for some of the surplus plutonium) and the MOX fuel approach (for some of the surplus plutonium); alternatives that would immobilize all of the surplus plutonium; and the No Action Alternative. The alternatives include three disposition facilities that would be designed so that they could collectively accomplish disposition of up to 50 metric tons (55 tons) of surplus plutonium over their operating lives: (1) the pit disassembly and conversion facility would disassemble pits (a weapons component) and convert the recovered plutonium, as well as plutonium metal from other sources, into plutonium dioxide suitable for disposition; (2) the immobilization facility would include a collocated capability for converting nonpit plutonium materials into plutonium dioxide suitable for immobilization and would be located at either Hanford or SRS. DOE has identified SRS as the preferred site for an immobilization facility; (3) the MOX fuel fabrication facility would fabricate plutonium dioxide into MOX fuel. Volume 2 contains the appendices to the report and describe the following: Federal Register notices; contractor nondisclosure statement; adjunct melter

  2. Charge distribution on plutonium-containing aerosols produced in mixed-oxide reactor fuel fabrication and the laboratory

    International Nuclear Information System (INIS)

    Yeh, H.C.; Newton, G.J.; Teague, S.V.

    1976-01-01

    The inhalation toxicity of potentially toxic aerosols may be affected by the electrostatic charge on the particles. Charge may influence the deposition site during inhalation and therefore its subsequent clearance and dose patterns. The electrostatic charge distributions on plutonium-containing aerosols were measured with a miniature, parallel plate, aerosol electrical mobility spectrometer. Two aerosols were studied: a laboratory-produced 238 PuO 2 aerosol (15.8 Ci/g) and a plutonium mixed-oxide aerosol (PU-MOX, natural UO 2 plus PuO 2 , 0.02 Ci/g) formed during industrial centerless grinding of mixed-oxide reactor fuel pellets. Plutonium-238 dioxide particles produced in the laboratory exhibited a small net positive charge within a few minutes after passing through a 85 Kr discharger due to alpha particle emission removal of valence electrons. PU-MOX aerosols produced during centerless grinding showed a charge distribution essentially in Boltzmann equilibrium. The gross alpha aerosol concentrations (960-1200 nCi/l) within the glove box were sufficient to provide high ion concentrations capable of discharging the charge induced by mechanical and/or nuclear decay processes

  3. Valence effects on adsorption: a preliminary assessment of the effects on valence state control on sorption measurements

    International Nuclear Information System (INIS)

    Meyer, R.E.; Arnold, W.D.; Case, F.; Shiao, S.Y.; Palmer, D.A.

    1983-01-01

    Electrochemical arguments are advanced to illustrate that what is usually measured in practice is a mixed potential determined by the kinetics of the electrode processes occurring at the indicator electrode. Valence states can be altered electrochemically or by use of added chemical reagents, including redox couples which can hold the potential to relatively specific potentials. The disadvantage of added chemical reagents is that they may alter the characteristics of the sorption reactions by interaction with the sorbent. Electrochemical methods are versatile and do not add reagents, but in some caes the nuclide can adsorb on the electrode itself. A description is given of the application of the electrochemical method of valence control to determination of sorption of Np(V) on alumina. Valence state control and analysis can be used to study possible redox reactions on materials which might be used as backfill materials. A description is given of survey experiments with a number of sulfides and iron-containing materials. Valence state analysis is used on the initial solutions and leachate from acid leaches of the sorbent after the sorption experiment to help determine whether valence state change is occurring. The preliminary results indicate that on the sulfides tested, sorption occurs both with and without valence state change

  4. Six-kilogram-scale electrorefining of plutonium metal

    International Nuclear Information System (INIS)

    Mullins, L.J.; Morgan, A.N.; Apgar, S.A. III; Christensen, D.C.

    1982-09-01

    The electrorefining of metallic plutonium scrap to produce high purity metal has been an established procedure at Los Alamos since 1964. This is a batch process and was limited to 4-kg plutonium because of criticality safety considerations. Improvements in critical mass measurements have permitted us to develop a process for 6-kg plutonium. The 6-kg process is now operational. The increased size of the process, together with other improvements which have been made, makes plutonium electrorefining the principal industrial tool for processing and purifying metallic plutonium scrap

  5. Qualitative chemical analysis of plutonium by Alpha spectroscopy

    International Nuclear Information System (INIS)

    Ramirez G, J Qumica.J.

    1994-01-01

    In this work the separation and purification of plutonium from irradiated uranium was done. The plutonium, produced by the irradiation of uranium in a nuclear reactor and the β decay of 239 Np, was stabilized to Pu +4 with sodium nitrite. Plutonium was separated from the fission products and uranium by ion exchange using the resin Ag 1 X 8. It was electrodeposited on stainless steel discs and the alpha radioactivity of plutonium was measured in a surface barrier detector. The results showed that plutonium was separated with a radiochemical purity higher than 99 %. (Author)

  6. Diffusion in the uranium - plutonium system and self-diffusion of plutonium in epsilon phase

    International Nuclear Information System (INIS)

    Dupuy, M.

    1967-07-01

    A survey of uranium-plutonium phase diagram leads to confirm anglo-saxon results about the plutonium solubility in α uranium (15 per cent at 565 C) and the uranium one in ζ phase (74 per cent at 565 C). Interdiffusion coefficients, for concentration lower than 15 per cent had been determined in a temperature range from 410 C to 640 C. They vary between 0.2 and 6 10 12 cm 2 s -1 , and the activation energy between 13 and 20 kcal/mole. Grain boundary, diffusion of plutonium in a uranium had been pointed out by micrography, X-ray microanalysis and α autoradiography. Self-diffusion of plutonium in ε phase (bcc) obeys Arrhenius law: D = 2. 10 -2 exp -(18500)/RT. But this activation energy does not follow empirical laws generally accepted for other metals. It has analogies with 'anomalous' bcc metals (βZr, βTi, βHf, U γ ). (author) [fr

  7. Progress on immobilisation of plutonium residues and shredded plutonium contaminated materials in cement

    International Nuclear Information System (INIS)

    Landles, A.J.; Awmack, A.F.; Baxter, W.

    1987-03-01

    Laboratory scale experiments have been carried out to study the feasibility of encapsulating plutonium contaminated materials in cement. A proposed grout of a 3:1 PFA/OPC mixture has been tested and some product evaluation carried out. (author)

  8. Simultaneous determinations of uranium, thorium, and plutonium in soft tissues by solvent extraction and alpha-spectrometry

    International Nuclear Information System (INIS)

    Singh, N.P.; Zimmerman, C.J.; Lewis, L.L.; Wrenn, M.E.

    1984-01-01

    A radiochemical procedure for the simultaneous determination of uranium, thorium, and plutonium, in soft tissues has been developed. The weighed amounts of tissues, spiked with 232 U, 242 Pu, and 229 th tracers, are wet ashed. Uranium, thorium, and plutonium are coprecipitated with iron as hydroxides, dissolved in concentrated HCl and the acidity adjusted to 10 M. Uranium and plutonium are extracted into 20% TLA solution in xylene, leaving thorium in the aqueous phase. Plutonium is back-extracted by reducing to the trivalent state with 0.05 M NH 4 I solution in 8 M HCl, and uranium is back-extracted with 0.1 M HCl. Thorium is extracted into 20% TLA solution from 4 M HNO 3 and back-extracted with 10 M HCl. Uranium, thorium and plutonium are electrodeposited separately onto platinum discs and counted alpha-spectrometrically using surface barrier silicon diodes and a multichannel analyzer. The method was developed using bovine liver and applied to dog and human tissues. The mean radiochemical recoveries of these actinides in different organs were better than 70%. 6 references, 2 tables

  9. Simultaneous determination of uranium and plutonium in dissolver solution of irradiated fuel, using ID-TIMS. IRP-11

    International Nuclear Information System (INIS)

    Shah, Raju; Sasi Bhushan, K.; Govindan, R.; Alamelu, D.; Khodade, P.S.; Aggarwal, S.K.

    2007-01-01

    A simple sample preparation and simultaneous analysis method to determine uranium and plutonium from dissolver solution, employing the technique of Isotope Dilution Mass spectrometry has been demonstrated. The method used, co-elusion of Uranium and Plutonium from anion exchanger column after initial elution of major part of uranium in 1:5 HNO 3 in order to reduce the initial U/Pu ratio from 1000 to about 100-200 in the co-eluted fraction. Due to the availability of variable multi-collector system, different Faraday cups were adjusted to collect the different ion intensities corresponding to the different masses, during the simultaneous analysis of Uranium and Plutonium, loaded on Re double filament assembly. 233 U and PR grade Plutonium were used as spikes to determine Uranium and Plutonium from dissolver solution of irradiated fuel from research reactor. The possibility of getting the isotopic composition of uranium from the simultaneous analysis of co-eluted purified fraction of U and Pu from spiked aliquots is also explained. (author)

  10. Interaction of plutonium with complexing substances in soils and natural waters

    International Nuclear Information System (INIS)

    Bondietti, E.A.; Reynolds, S.A.; Shanks, M.H.

    1976-01-01

    The reactions of Pu with selected organic substances found in the environment have been studied to evaluate the valence and metalcomplex behaviour of Pu. Hexavalent Pu (and by inference pentavalent Pu) was unstable in the presence of fulvic acid, polygalacturonic acid, and alginic acid. Citrate-Pu(VI) complexes, however, were relatively more stable. Plutonium (IV) was the most stable valence upon interaction with these organics. Further reduction of Pu(IV) to Pu(III) occurred by fulvic and humic acids. The reduction, under aerobic conditions, does not appear to occur above pH 3.1. The reduction mechanisms is probably similar to the Fe(III) reduction previously documented for phenolic humic substances. Data are presented that demonstrate that Pu is at least partially associated with humic materials in ORNL soil contaminated 30 years ago with trace levels of Pu. Desorption studies using solid exchange resins also showed that, while a cation exchange resin did not desorb Pu from soil after 14 weeks equilibration, chelating resin effected Pu desorption. The desorption rate was not constant, suggesting differential Pu forms. While the resin-extractable Pu was believed to originate from solid-phase organic complexes, over 80% of the Pu in this soil was not readily resin-desorbable. This indicates that more inert soil-Pu reaction products effectively immobilize soil Pu. Some of these associations also appear to be organic. (author)

  11. Decomposition kinetics of plutonium hydride

    Energy Technology Data Exchange (ETDEWEB)

    Haschke, J.M.; Stakebake, J.L.

    1979-01-01

    Kinetic data for decomposition of PuH/sub 1/ /sub 95/ provides insight into a possible mechanism for the hydriding and dehydriding reactions of plutonium. The fact that the rate of the hydriding reaction, K/sub H/, is proportional to P/sup 1/2/ and the rate of the dehydriding process, K/sub D/, is inversely proportional to P/sup 1/2/ suggests that the forward and reverse reactions proceed by opposite paths of the same mechanism. The P/sup 1/2/ dependence of hydrogen solubility in metals is characteristic of the dissociative absorption of hydrogen; i.e., the reactive species is atomic hydrogen. It is reasonable to assume that the rates of the forward and reverse reactions are controlled by the surface concentration of atomic hydrogen, (H/sub s/), that K/sub H/ = c'(H/sub s/), and that K/sub D/ = c/(H/sub s/), where c' and c are proportionality constants. For this surface model, the pressure dependence of K/sub D/ is related to (H/sub s/) by the reaction (H/sub s/) reversible 1/2H/sub 2/(g) and by its equilibrium constant K/sub e/ = (H/sub 2/)/sup 1/2//(H/sub s/). In the pressure range of ideal gas behavior, (H/sub s/) = K/sub e//sup -1/(RT)/sup -1/2/ and the decomposition rate is given by K/sub D/ = cK/sub e/(RT)/sup -1/2/P/sup 1/2/. For an analogous treatment of the hydriding process with this model, it can be readily shown that K/sub H/ = c'K/sub e//sup -1/(RT)/sup -1/2/P/sup 1/2/. The inverse pressure dependence and direct temperature dependence of the decomposition rate are correctly predicted by this mechanism which is most consistent with the observed behavior of the Pu--H system.

  12. The first metallurgical tests on plutonium; Premiers essais metallurgiques sur le plutonium

    Energy Technology Data Exchange (ETDEWEB)

    Grison, E; Abramson, R; Anselin, F; Monti, H [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1958-07-01

    Metallic plutonium was first prepared in France in January 1956, as soon as we had access to quantities of the order of several grams of plutonium, which had been extracted from the rods of the pile EL2 at Saclay. Since up to the present this reactor, of thermal power 2 000 kW, has been our only source of plutonium, we have so far only worked on experimental quantities sufficient for the basic tests but not for tests on a scale of possible applications. It is this work, carried out during this phase of preliminary research, which is described below. With the starting up of the plutonium extraction plant at Marcoule, where the reactor G1 has been operating at power for more than a year, we shall go on next to a another order of magnitude which will allow the manufacture and experimentation of prototype fuel elements. (author) [French] La premiere elaboration de plutonium metallique en France fut faite en janvier 1956, des que nous pumes disposer de quantites de plutonium de l'ordre de quelques grammes, qui avaient ete retires des barreaux de la pile EL2 de Saclay. Ce reacteur, d'une puissance thermique de 2 000 kW, ayant ete jusqu'a present notre seule source de plutonium, nous n'avons encore travaille que sur des quantites experimentales suffisantes pour les essais de base, mais non pour des essais a l'echelle d'applications possibles. Ce sont les travaux effectues pendant cette phase de recherches preliminaires qui seront evoques ci-dessous. Avec la mise eu route de l'usine d'extraction de plutonium de Marcoule, ou le reacteur G1 fonctionne en puissance depuis plus d'un an, nous allons passer prochainement a un autre ordre de grandeur, qui nous permettra la fabrication et l'experimentation d'elements combustibles prototypes. (auteur)

  13. Weapons-grade plutonium dispositioning. Volume 2: Comparison of plutonium disposition options

    Energy Technology Data Exchange (ETDEWEB)

    Brownson, D.A.; Hanson, D.J.; Blackman, H.S. [and others

    1993-06-01

    The Secretary of Energy requested the National Academy of Sciences (NAS) Committee on International Security and Arms Control to evaluate disposition options for weapons-grade plutonium. The Idaho National Engineering Laboratory (INEL) offered to assist the NAS in this evaluation by investigating the technical aspects of the disposition options and their capability for achieving plutonium annihilation levels greater than 90%. This report was prepared for the NAS to document the gathered information and results from the requested option evaluations. Evaluations were performed for 12 plutonium disposition options involving five reactor and one accelerator-based systems. Each option was evaluated in four technical areas: (1) fuel status, (2) reactor or accelerator-based system status, (3) waste-processing status, and (4) waste disposal status. Based on these evaluations, each concept was rated on its operational capability and time to deployment. A third rating category of option costs could not be performed because of the unavailability of adequate information from the concept sponsors. The four options achieving the highest rating, in alphabetical order, are the Advanced Light Water Reactor with plutonium-based ternary fuel, the Advanced Liquid Metal Reactor with plutonium-based fuel, the Advanced Liquid Metal Reactor with uranium-plutonium-based fuel, and the Modular High Temperature Gas-Cooled Reactor with plutonium-based fuel. Of these four options, the Advanced Light Water Reactor and the Modular High Temperature Gas-Cooled Reactor do not propose reprocessing of their irradiated fuel. Time constraints and lack of detailed information did not allow for any further ratings among these four options. The INEL recommends these four options be investigated further to determine the optimum reactor design for plutonium disposition.

  14. Weapons-grade plutonium dispositioning. Volume 2: Comparison of plutonium disposition options

    International Nuclear Information System (INIS)

    Brownson, D.A.; Hanson, D.J.; Blackman, H.S.

    1993-06-01

    The Secretary of Energy requested the National Academy of Sciences (NAS) Committee on International Security and Arms Control to evaluate disposition options for weapons-grade plutonium. The Idaho National Engineering Laboratory (INEL) offered to assist the NAS in this evaluation by investigating the technical aspects of the disposition options and their capability for achieving plutonium annihilation levels greater than 90%. This report was prepared for the NAS to document the gathered information and results from the requested option evaluations. Evaluations were performed for 12 plutonium disposition options involving five reactor and one accelerator-based systems. Each option was evaluated in four technical areas: (1) fuel status, (2) reactor or accelerator-based system status, (3) waste-processing status, and (4) waste disposal status. Based on these evaluations, each concept was rated on its operational capability and time to deployment. A third rating category of option costs could not be performed because of the unavailability of adequate information from the concept sponsors. The four options achieving the highest rating, in alphabetical order, are the Advanced Light Water Reactor with plutonium-based ternary fuel, the Advanced Liquid Metal Reactor with plutonium-based fuel, the Advanced Liquid Metal Reactor with uranium-plutonium-based fuel, and the Modular High Temperature Gas-Cooled Reactor with plutonium-based fuel. Of these four options, the Advanced Light Water Reactor and the Modular High Temperature Gas-Cooled Reactor do not propose reprocessing of their irradiated fuel. Time constraints and lack of detailed information did not allow for any further ratings among these four options. The INEL recommends these four options be investigated further to determine the optimum reactor design for plutonium disposition

  15. Work at Aldermaston on plutonium binding with biological systems

    International Nuclear Information System (INIS)

    Popplewell, D.S.

    1976-01-01

    Over a number of years, the Chemistry Division of AWRE, Aldermaston, studied the nature of plutonium in various biological systems. The object of the work was to identify those natural products of the body which play a part in the transport and deposition of accidental intakes of plutonium. These results should be of value in formulating more effective therapeutic measures for plutonium removal from the body. The paper reviews the work at AWRE on the interaction of plutonium with serum and rat liver. Experiments on the uptake of plutonium into cell cultures are described. The aim of these experiments was to see whether a model system could be set up for testing the efficacy by which chelating agents could remove plutonium from within cells. A simple hypothesis is presented for the mode of transport of plutonium within animals. (author)

  16. Plutonium in the ocean environment. Its distributions and behavior

    International Nuclear Information System (INIS)

    Hirose, Katsumi

    2009-01-01

    Marine environments have been extensively contaminated by plutonium as a result of global fallout due to atmospheric nuclear-weapons testing. Knowledge of the levels and behavior of plutonium in marine environments is necessary to assess the radiological and ecological effects of plutonium. Such analytical techniques as radiochemical analysis, α-spectrometry, and mass spectrometry have been developed to analyze the plutonium in seawater over the past five decades. Because of complex chemical properties (e.g. high reactivity to particles), plutonium in the ocean exhibits more complicated behavior than other long-lived anthropogenic radionuclides, such as 137 Cs. In the present study. In reviewed the research history of plutonium in the ocean, including spatial and temporal changes of plutonium levels and distributions, and its oceanographic behavior. (author)

  17. Recent trends of plutonium facilities and their control

    Energy Technology Data Exchange (ETDEWEB)

    Muto, T [Power Reactor and Nuclear Fuel Development Corp., Tokai, Ibaraki (Japan). Tokai Works

    1974-02-01

    Much interest has been focussed on Pu recycle since the oil crisis because of an expected shortage of enriched uranium. Plutonium handling techniques and plutonium fuel fabricating facilities should be developed to meet the future demand of plutonium, but the radioactive property of plutonium to be reprocessed from spent fuel and recycled plutonium is remarkably different, and it has to be handled safely. Technical criteria for plutonium facilities are specified in the USAEC regulatory guides and other rules. Some of these criteria are location condition, quality of confinement, protection against accidents and so on. The control conditions for plutonium facilities are exposure control, criticality control, measurement control and new system of safeguard. These problems are under development to meet the future requirement for the safe handling of Pu material.

  18. Determination of plutonium in soils by mass spectrometry

    International Nuclear Information System (INIS)

    Storms, H.A.; Carlson, D.C.; Hunter, F.F.

    1974-01-01

    A procedure is described in which mass spectrometry is utilized for the determination of plutonium in soils. Using this procedure we have measured plutonium isotopic compositions at concentrations as low as 2 x 10 -14 grams Pu per gram soil. A thermal ionization source with canoe-shaped rhenium filament, is utilized in the mass spectrometer. The plutonium, when loaded onto the filament, is contained in a single Dowex-1 resin bead which is about 350 micrometers in diameter. Concentrating the plutonium within this single bead is a key step in the procedure and produces a relatively clean plutonium fraction. The resin bead also serves as an effective diffusion barrier such that the plutonium is prevented from being removed with the lower boiling impurities. The Pu remains in the bead until the temperature is sufficiently high for efficient production of Pu + ions. Plutonium ionization efficiencies as high as 2.5 percent have been measured

  19. Polarographic study of the electrochemical properties of plutonium; Etude polarographique des proprietes electrochimiques du plutonium

    Energy Technology Data Exchange (ETDEWEB)

    Guichard, C [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

    1968-07-01

    The behaviour of the different degrees of oxidation of plutonium have been studied using a falling drop mercury electrode in a non-complexing medium: dilute perchloric acid. In this medium it is possible to carry out the polarographic determination of plutonium using the reduction step situated at - 0.54 V/ECS which corresponds to the passage from the degree of oxidation(V) to the degree(III). The modifications brought about by a complexing ion, acetate, are then observed and interpreted. The existence of two plutonium(IV) acetic complexes has been shown; one is a polymerized substance. (author) [French] Le comportement des differents degres d'oxydation du plutonium est etudie a l'electrode a gouttes de mercure dans un milieu non complexant: l'acide perchlorique dilue. Il est possible dans ce milieu d'effectuer le dosage polarographique du plutonium en utilisant la vague de reduction situee a - 0.54 V/ECS qui correspond au passage du degre d'oxydation(V) au degre(III). Les modifications apportees par un ion complexant, l'acetate, sont ensuite observees et interpretees. Deux complexes acetiques du plutonium(IV) ont ete mis en evidence, dont l'un est un compose polymerise. (auteur)

  20. Western Option - Disarmament of Russian Weapon Plutonium

    International Nuclear Information System (INIS)

    Tveiten, B.; Petroll, M.R.

    2002-01-01

    The Western Option concept describes an approach to the conversion of weapon-grade plutonium from Russian nuclear warheads under the special aspects of meeting the criteria of irreversible utilization. Putting this concept of plutonium conversion into non-weapon-grade material into effect would make a major contribution to improving security worldwide. This study is based on an agreement between the Russian Federation and the United States of America concluded in September 2000. It provides for the conversion of 34 t of weapon-grade plutonium in each of the two states. This goal is also supported by other G8 countries. While the United States performs its part of the agreement under its sole national responsibility, the Russian program needs financial support by Western states. Expert groups have pointed out several options as a so-called basic scenario. The funds of approx. US Dollar 2 billion required to put them into effect have not so far been raised. The Western Option approach described in this contribution combines results of the basic scenario with other existing experience and with technical solutions available for plutonium conversion. One of the attractions of the Western Option lies in its financial advantages, which are estimated to amount to approx. US Dollar 1 billion. (orig.) [de