WorldWideScience

Sample records for platform purge flow

  1. Exploration EVA Purge Flow Assessment

    Science.gov (United States)

    Navarro, Moses; Conger, Bruce; Campbell, Colin

    2011-01-01

    An advanced future spacesuit will require properly sized suit and helmet purge flow rates in order to sustain a crew member with a failed Portable Life Support System (PLSS) during an Extravehicular Activity (EVA). A computational fluid dynamics evaluation was performed to estimate the helmet purge flow rate required to washout carbon dioxide and to prevent the condensing ("fogging") of water vapor on the helmet visor. An additional investigation predicted the suit purge flow rate required to provide sufficient convective cooling to keep the crew member comfortable. This paper summarizes the results of these evaluations.

  2. New Approach to Purging Monitoring Wells: Lower Flow Rates Reduce Required Purging Volumes and Sample Turbidity

    Science.gov (United States)

    It is generally accepted that monitoring wells must be purged to access formation water to obtain “representative” ground water quality samples. Historically anywhere from 3 to 5 well casing volumes have been removed prior to sample collection to evacuate the standing well water...

  3. Effects of Purge-Flow Rate on Microbubble Capture in Radial Arterial-Line Filters.

    Science.gov (United States)

    Herbst, Daniel P

    2016-09-01

    The process of microbubble filtration from blood is complex and highly dependent on the forces of flow and buoyancy. To protect the patient from air emboli, arterial-line filters commonly use a micropore screen, a large volume housing with purpose-built shape, and a purge port to trap, separate, and remove circulating microbubbles. Although it has been proposed that an insufficient buoyancy force renders the purge port ineffective at removing microbubbles smaller than 500 μm, this research attempts to investigate the purge flow of an arterial-line filter to better understand the microbubble removal function in a typical radial filter design. As its primary objective, the study aims to determine the effect of purge-flow rate on bubble capture using air bolus injections from a syringe pump with 22-gauge needle and Doppler ultrasound bubble detection. The measureable bubble size generated in the test circuit ranged between 30 and 500 μm, while purge flow was varied between .1 and .5 L/min for testing. Statistical analysis of the test data was handled using a repeated measures design with significance set at p purge flows yielded higher bubble counts, but the effect of purge-flow rate on bubble capture decreased as bubble size increased. Results also showed that purge flow from the test filter was capable of capturing all bubble sizes being generated over the entire flow range tested, and confirms utility of the purge port in removing microbubbles smaller than 500 μm. By analyzing bubble counts in the purge flow of a typical radial-filter design, this study demonstrates that currently available micropore filter technology is capable of removing the size range of bubbles that commonly pass through modern pump-oxygenator systems and should continue to be considered during extracorporeal circulation as a measure to improve patient safety.

  4. Update on Advection-Diffusion Purge Flow Model

    Science.gov (United States)

    Brieda, Lubos

    2015-01-01

    Gaseous purge is commonly used in sensitive spacecraft optical or electronic instruments to prevent infiltration of contaminants and/or water vapor. Typically, purge is sized using simplistic zero-dimensional models that do not take into account instrument geometry, surface effects, and the dependence of diffusive flux on the concentration gradient. For this reason, an axisymmetric computational fluid dynamics (CFD) simulation was recently developed to model contaminant infiltration and removal by purge. The solver uses a combined Navier-Stokes and Advection-Diffusion approach. In this talk, we report on updates in the model, namely inclusion of a particulate transport model.

  5. Numerical investigation of the interaction between upstream cavity purge flow and main flow in low aspect ratio turbine cascade

    Institute of Scientific and Technical Information of China (English)

    Jia Wei; Liu Huoxing

    2013-01-01

    In modem gas turbines,rim seal located between the stator-disc and rotor-disc is used to prevent hot-gas ingestion into the inner stage-gap of high pressure turbine.However,the purge flow supplied to the cavity through the rim seal interacts with the main flow,producing additional aerodynamic loss due to the mixing process which plays a significant role in the formation,development and evolution of downstream secondary flow.In this paper,a set of cascade representative of low aspect ratio turbine is selected to numerically investigate the influence of upstream cavity purge flow on the hub secondary flow structure and aerodynamic loss.Cascade with/without upstream cavity and four different purge mass flow rates are all taken into account in this simulation.Then,a deep insight into the loss mechanism of interaction between purge flow and main flow is gained.The results show that the presence of cavity and purge flow has a significant impact on the main flow which not only changes the vortex structure in both the passage and upstream cavity,but also alters the cascade exit flow angle distribution along the spanwise.Moreover,aerodynamic loss in the cascade rises with the increase of purge flow rate while the sealing effect is also enhanced.Therefore,the effect of upstream cavity purge flow must be considered in the process of turbine aerodynamic design.What is more,it is necessary to minimize the purge flow rate in order to reduce aerodynamic loss on the premise of satisfying cooling requirements.

  6. Tri-leaflet valve design with a purge flow for heart-assist devices: an in vitro optimization study.

    Science.gov (United States)

    Timmel, Tobias; Seshadri, Santhosh; Goubergrits, Leonid; Affeld, Klaus; Kertzscher, Ulrich

    2012-01-01

    The objective of this study is to assess the effect of a purge flow on valves of pulsatile heart-assist devices. Clinical applications of these devices are still limited because of frequent thromboembolic complications. These complications often originate at the valves and the unavoidable flow separation regions that are found behind the leaflets. The flow separations cause a long residence time of blood that is considered particularly detrimental. To solve this problem, a valve with a purge flow is proposed. A purge flow is a jet, which is separated from the main blood flow and directed behind the leaflets into the sinus to flush it. Even though the purge flow does not prevent a flow separation, it shortens the residence time of the blood in the sinus. Thus, the purge flow improves the periodic washout of the blood in the region of flow separation. The complex purge flow was investigated in a tri-leaflet valve. The geometrical parameters of the valve were varied systematically. A statistical technique--the Taguchi method--was used to reduce the number of investigated models to 12. The flows through the resulting valve models were numerically simulated and analyzed. The evaluated models with the best results were subsequently investigated experimentally using different methods: hemodynamic tests in a valve tester and flow visualization using the dye washout method. It was shown that the purge flow can effectively wash out the sinus. Therefore, the purge flow valve reduces the potential of a thrombus formation normally associated with the valve.

  7. "Stolen" blood flow: effect of an open arterial filter purge line in a simulated neonatal CPB model.

    Science.gov (United States)

    Wang, Shigang; Miller, Akemi; Myers, John L; Undar, Akif

    2008-01-01

    The purpose of this study was to evaluate the effect of different flow rates and pressures on the degree of shunting of blood flow by the arterial filter purge line in a simulated neonatal cardiopulmonary bypass circuit. The circuit was primed with heparinized bovine blood (hematocrit 24%) and postfilter pressure was varied from 60-180 mm Hg (20 mm Hg increments) using a Hoffman clamp. Trials were conducted at flow rates ranging from 200-600 ml/min (100 ml/min increments). During trials conducted at a postfilter pressure of 60 mm Hg, 42.6% of blood flow was shunted through the purge line at a flow rate of 200 ml/min, whereas only 12.8% of flow was diverted at a flow rate 600 ml/min. During trials conducted at a postfilter pressure of 180 mm Hg, 82.8% of blood flow at 200 ml/min and 25.9% of blood flow at 600 ml/min was diverted through the open arterial purge line. The results of this study confirm that a significant amount of flow is diverted away from the patient when the arterial purge line is open. Shunting of blood flow through the arterial purge line could result in less effective tissue perfusion, particularly at low flow rates and high postfilter pressures. To minimize hypoperfusion injury, a flow probe (distal to the arterial filter) may be used to monitor real-time arterial flow in the setting of an open arterial filter purge line.

  8. A purge and trap integrated microGC platform for chemical identification in aqueous samples.

    Science.gov (United States)

    Akbar, Muhammad; Narayanan, Shree; Restaino, Michael; Agah, Masoud

    2014-07-07

    The majority of current micro-scale gas chromatography (μGC) systems focus on air sampling to detect volatile organic compounds (VOCs). However, purging the VOCs from a water sample using microsystems is an unchartered territory. Various organic compounds used in everyday life find their way to water bodies. Some of these water organic compounds (WOCs) persist or degrade slowly, threatening not just human existence but also aquatic life. This article reports the first micro-purge extractor (μPE) chip and its integration with a micro-scale gas chromatography (μGC) system for the extraction and analysis of water organic compounds (WOCs) from aqueous samples. The 2 cm × 3 cm μPE chip contains two inlet and outlet ports and an etched cavity sealed with a Pyrex cover. The aqueous sample is introduced from the top inlet port while a pure inert gas is supplied from the side inlet to purge WOCs from the μPE chip. The outlets are assigned for draining water from the chip and for directing purged WOCs to the micro-thermal preconcentrator (μTPC). The trapped compounds are desorbed from the μTPC by resistive heating using the on-chip heater and temperature sensor, are separated by a 2 m long, 80 μm wide, and 250 μm deep polydimethylsiloxane (OV-1) coated μGC separation column, and are identified using a micro-thermal conductivity detector (μTCD) monolithically integrated with the column. Our experiments indicate that the combined system is capable of providing rapid chromatographic separation (<1.5 min) for quaternary WOCs namely toluene, tetrachloroethylene (PCE), chlorobenzene and ethylbenzene with a minimum detection concentration of 500 parts-per-billion (ppb) in aqueous samples. The proposed method is a promising development towards the future realization of a miniaturized system for sensitive, on-site and real-time field analysis of organic contaminants in water.

  9. Purged window apparatus utilizing heated purge gas

    Science.gov (United States)

    Ballard, Evan O.

    1984-01-01

    A purged window apparatus utilizing tangentially injected heated purge gases in the vicinity of electromagnetic radiation transmitting windows, and a tapered external mounting tube to accelerate these gases to provide a vortex flow on the window surface and a turbulent flow throughout the mounting tube. Use of this apparatus prevents backstreaming of gases under investigation which are flowing past the mouth of the mounting tube which would otherwise deposit on the windows. Lengthy spectroscopic investigations and analyses can thereby be performed without the necessity of interrupting the procedures in order to clean or replace contaminated windows.

  10. Conserving Purge Gases

    Science.gov (United States)

    Kan, K.; Blewett, L.; Nelson, T.

    1985-01-01

    Two-step flow control adjusts to dimensional changes in purged equipment. Two pressure actuated valves provide two-step control. When turbopump starts, helium flows through both valves. As pump operates its parts expand, clearance decrease and back pressure builds up on valves. At preset back pressure value, one valve closes, reducing helium flow.

  11. Performance of Gas Purge System of Absorption Refrigerating Machine

    Science.gov (United States)

    Kunugi, Yoshifumi; Ouchi, Tomihisa; Usui, Sanpei; Sugimoto, Shigeo

    Experimental studies on performance of two gas purge systems for the lithium bromide-water absorption refrigerating machine are presented in this paper. The first purge system is that the solution flow entrains the incondensable gas from the absorber in the first purge chamber, then the incondesable gas from the condenser in the second purge chamber. The second purge system is that the solution flow entrains the incondensable gas, separates it in the separator, and then returns to the refrigerating machine through the inverted U tube. As a result, purged gas rate of both gas purge systems conforms to the theoretical equation ; S=V0(P-P0), where S is purged gas rate, V0 is exhaust gas rate, P is pressure of purge chamber, and P0 is saturated vapor pressure of solution.

  12. Purge corruption detection

    Energy Technology Data Exchange (ETDEWEB)

    Nankee, R.J. II; Frantz, D.C.; Tamm, J.R.; Gutermuth, T.R.

    1989-04-18

    This patent describes an adaptive memory cell update method for the detection and correction of a possible purge corruption of the adaptive memory portion of the memory in an internal combustion engine control unit, the adaptive memory portion having purge free cells and normal cells. The method consists of: determining the adaptive memory cells to be used during the adaptive memory cell update by determining if the engine conditions are right to turn the purge system off; if the conditions are right to turn the purge system off, turning the purge system off and using the purge free cells in the adaptive memory cell update; if the conditions are not right to turn the purge system off, turning the purge system on and using the normal cells in the adaptive memory cell update.

  13. Coal slurry fuel supply and purge system

    Science.gov (United States)

    McDowell, Robert E.; Basic, Steven L.; Smith, Russel M.

    1994-01-01

    A coal slurry fuel supply and purge system for a locomotive engines is disclosed which includes a slurry recirculation path, a stand-by path for circulating slurry during idle or states of the engine when slurry fuel in not required by the engine, and an engine header fluid path connected to the stand-by path, for supplying and purging slurry fuel to and from fuel injectors. A controller controls the actuation of valves to facilitate supply and purge of slurry to and from the fuel injectors. A method for supplying and purging coal slurry in a compression ignition engine is disclosed which includes controlling fluid flow devices and valves in a plurality of fluid paths to facilitate continuous slurry recirculation and supply and purge of or slurry based on the operating state of the engine.

  14. Purge water management system

    Science.gov (United States)

    Cardoso-Neto, Joao E.; Williams, Daniel W.

    1996-01-01

    A purge water management system for effectively eliminating the production of purge water when obtaining a groundwater sample from a monitoring well. In its preferred embodiment, the purge water management system comprises an expandable container, a transportation system, and a return system. The purge water management system is connected to a wellhead sampling configuration, typically permanently installed at the well site. A pump, positioned with the monitoring well, pumps groundwater through the transportation system into the expandable container, which expands in direct proportion with volume of groundwater introduced, usually three or four well volumes, yet prevents the groundwater from coming into contact with the oxygen in the air. After this quantity of groundwater has been removed from the well, a sample is taken from a sampling port, after which the groundwater in the expandable container can be returned to the monitoring well through the return system. The purge water management system prevents the purge water from coming in contact with the outside environment, especially oxygen, which might cause the constituents of the groundwater to oxidize. Therefore, by introducing the purge water back into the monitoring well, the necessity of dealing with the purge water as a hazardous waste under the Resource Conservation and Recovery Act is eliminated.

  15. Real-time multivariate statistical classification of cells for flow cytometry and cell sorting: a data mining application for stem cell isolation and tumor purging

    Science.gov (United States)

    Leary, James F.; McLaughlin, Scott R.; Reece, Lisa M.; Rosenblatt, Judah I.; Hokanson, James A.

    1999-06-01

    Multivariate statistics can be used for visualization of cell subpopulations in multidimensional data space and for classification of cells within that data space. New data mining techniques we have developed, such as subtractive clustering, can be used to find the differences between test and control multiparameter flow cytometric data, e.g. in the problem of human stem cell isolation with tumor purging. They also can provide training data for subsequent multivariate statistical classification techniques such as discriminant function or logistic regression analyses. Using lookup tables, these multivariate statistical calculations can be performed in real-time, and can even include probabilities of misclassification. Thus, the only distinction between off-line classification of cells in data analysis and real-time statistical decision-making for cell sorting is the time limit in which a classification decision must be made. For real-time cell sorting we presently are able to perform these classifications in less than 625 microseconds, corresponding to the time that it takes the cell to travel from the laser intersection point to the sort decision point in a flow cytometer/cell sorter. Statistical decision making and the ability to include the costs of misclassification into that decision process will become important as flow cytometry/cell sorting moves from diagnostics to therapeutics.

  16. 排尘孔涡轮冷却叶片叶顶流动与传热研究%Tip Flow and Heat Transfer Prediction of Cooling Blade with Dirt Purge Holes

    Institute of Scientific and Technical Information of China (English)

    虞跨海; 杨茜; 岳珠峰

    2012-01-01

    涡轮叶片叶顶排尘孔用于清除冷气中掺杂的尘粒,以保证气膜孔和冲击孔的可靠工作,但排尘孔射流引起叶顶流动和传热问题.采用参数化方法建立有、无排尘孔涡轮冷却叶片几何模型,基于包含叶片主体、主燃气通道和三腔回流式内冷却通道的全局模型,采用流热耦合数值分析,开展排尘孔对涡轮冷却叶片叶顶流动与传热问题的初步研究.研究结果表明,对比有、无排尘孔叶片,排尘孔射流可降低叶顶平均温度约25 K;冷却通道对流换热作用和叶顶排尘孔射流可使叶顶平面降温400~600 K,冷却效果与冷却通道冷气流量和尘孔结构在叶顶位置相关;排尘孔叶顶射流对叶顶间隙高温燃气泄漏具有阻碍作用,可以提高叶片总压恢复系数约0.5%~1.5%,随着冷气流量的增大,这种作用增强;尘孔结构设计应兼顾射流对叶顶流动与传热的共同影响.%Dirty purge holes in the blade tip are used to extract dirt from the coolant flow through centrifugal forces such that these dirt particles do not block small diameter film-cooling holes and injection holes, to ensure safety and reliability of the blade. Whereas, the holes will affect blade tip flow and heat transfer. A numerical study of a turbine blade with dirt purge holes is performed to examine both flow and heat transfer characteristics. Two blade geometry models with and without dirty purge holes are established by a parametric method in CAD software. Coupled aerodynamic and heat transfer numerical simulation is used to predict the blade tip flow and heat transfer, with the integral of the blade solid field, main gas and internal cooling passage flow field. The result shows that, the cool air jet from purge holes can reduce the tip facet average temperature about 25 K, based on the contrast between blades with and without dirty purge holes. Convective heat transfer of internal cooling passage and jet flow of dirty

  17. Purge efficiency in the determination of trihalomethanes in water by purge-and-trap gas chromatography.

    Science.gov (United States)

    Ruiz-Bevia, Francisco; Fernandez-Torres, Maria J; Blasco-Alemany, Maria P

    2009-01-26

    Purge-and-trap gas chromatography-mass spectrometry (PT-GC-MS) has become an accepted method for the analysis of trihalomethanes (THMs) in water. The purge-and-trap technique is based on an efficient transfer of volatile organic compounds from the liquid (contained in the purge chamber) to the gaseous phase by bubbling with an inert gas. The aim of this work was to study the purge system's efficiency by means of several consecutive purge cycles lasting 11 min each of the same liquid sample. The concentration range chosen of THMs was very wide [5-200 microg L(-1)]. The inert gas flow rate was 40 mL min(-1), and experiments were performed at temperatures of 25, 35 and 50 degrees C. Bromoform (CHBr(3)), the least volatile compound, needed 19 cycles to be purged quantitatively at a concentration of 200 microg L(-1) and only 7 cycles at 5 microg L(-1) for a 25 mL sample at 25 degrees C. Chloroform (CHCl(3)), the most volatile compound, required 4 cycles to be fully extracted at 200 microg L(-1) and 2 at 5 microg L(-1). Finally, Novak's theoretical model, based on the distribution constant between gas and liquid phases, was used to correlate the THMs purging extraction data.

  18. TO PURGE OR NOT TO PURGE? VOC CONCENTRATION ...

    Science.gov (United States)

    Soil vapor surveys are commonly used as a screening technique to delineate volatile organic compound (VOC) contaminant plumes and provide information for soil sampling plans. Traditionally, three purge volumes of vapor are removed before a sample is collected. One facet of this study was to evaluate the VOC concentrations lost during purging and explore the potential implications of those losses. The vapor data was compared to collocated soil data to determine if any correlation existed between the VOC concentrations. Two different methods for soil vapor collection were compared: 1) active/micro-volume; and 2) active/macro-volume. The active/micro-volume vapor sample had total line purge volume of 1.25 mL and the active/macro-volume vapor sample had a total line purge volume of 15 mL. Six line purge volumes were collected for each vapor sampling technique, with the fourth purge volume representing the traditional sample used for site screening data. Each sample was collected by gas tight syringe and transferred to a thermal de sorption tube for sorption, transport, and analysis. Following the removal of the soil vapor samples, collocated soil samples were taken. For both active vapor sampling techniques, the VOC concentrations in the first three purge volumes exceeded the VOC concentrations in the last three purge volumes. This implies that the general rule of removal of three purge volumes prior to taking a sample for analysis could lead to underestimating the

  19. ZAP: Zurich Atmosphere Purge

    Science.gov (United States)

    Soto, Kurt T.; Lilly, Simon J.; Bacon, Roland; Richard, Johan; Conseil, Simon

    2016-02-01

    ZAP (Zurich Atmosphere Purge) provides sky subtraction for integral field spectroscopy; its approach is based on principal component analysis (PCA) developed for the Multi Unit Spectrographic Explorer (MUSE) integral field spectrograph. ZAP employs filtering and data segmentation to enhance the inherent capabilities of PCA for sky subtraction. ZAP reduces sky emission residuals while robustly preserving the flux and line shapes of astronomical sources; this method works in a variety of observational situations from sparse fields with a low density of sources to filled fields in which the target source fills the field of view. With the inclusion of both of these situations the method is generally applicable to many different science cases and should also be useful for other instrumentation.

  20. Mapping flow distortion on oceanographic platforms using computational fluid dynamics

    Directory of Open Access Journals (Sweden)

    N. O'Sullivan

    2013-10-01

    Full Text Available Wind speed measurements over the ocean on ships or buoys are affected by flow distortion from the platform and by the anemometer itself. This can lead to errors in direct measurements and the derived parametrisations. Here we computational fluid dynamics (CFD to simulate the errors in wind speed measurements caused by flow distortion on the RV Celtic Explorer. Numerical measurements were obtained from the finite-volume CFD code OpenFOAM, which was used to simulate the velocity fields. This was done over a range of orientations in the test domain from −60 to +60° in increments of 10°. The simulation was also set up for a range of velocities, ranging from 5 to 25 m s−1 in increments of 0.5 m s−1. The numerical analysis showed close agreement to experimental measurements.

  1. Evaluation of Innovative High Pulse Rate, Purged Spark Gap Concepts

    Science.gov (United States)

    1989-06-01

    gugh the switch and the pressure loss through the gas circulation system. The pressure loss is the sum of the losses in the spark gap , flow ducting...developed to solve the mass, momentum, and energy conservation equations which govern the purging process in a spark gap flow channel following arc...formation. [2,3] In this model, gas properties and spark gap flow channel area varied with distance along the flow axis from the spark gap and with

  2. THEORETICAL ANALYSIS OF USING AIRFLOW TO PURGE RESIDUAL WATER IN AN INCLINED PIPE

    Institute of Scientific and Technical Information of China (English)

    SHEN Fang(沈芳); YAN Zong-yi(严宗毅); ZHAO Yao-hua(赵耀华); Kiyoshi Horii

    2002-01-01

    A refined theoretical analysis for using the spiral airflow and axial airflow to purge residual water in an inclined pipe was presented. The computations reveal that, in most cases, the spiral flow can purge the residual water in the inclined pipe indeed while the axial flow may induce back flow of the water, just as predicted in the experiments presented by Horii and Zhao et al. In addition, the effects of various initial conditions on water purging were studied in detail for both the spiral and axial flow cases.

  3. Cyclically controlled welding purge chamber

    Science.gov (United States)

    Gallagher, Robert L. (Inventor)

    1996-01-01

    An arrangement for butt-welding cylindrical sections of large, thin-wall tanks includes a rotatable mandrel with side-by-side sets of radial position adjusters. Each set of adjusters bears on one of the tank sections adjacent the seam, to prevent the sections from sagging out-of-round. The mandrel rotates relative to the welder, so that a continuous seam is formed. A purge chamber is fixed in position behind the seam at the weld head, and is flushed with inert gas. The purge chamber includes a two-sided structure which is contiguous with the cylindrical sections and a circumferential vane to form an open-ended tube-like structure, through which the radial position adjusters pass as the mandrel and cylindrical workpiece sections rotate. The tube-like structure is formed into a chamber by a plurality of movable gates which are controlled to maintain a seal while allowing adjusters to progress through the purge chamber.

  4. AP600 containment purge radiological analysis

    Energy Technology Data Exchange (ETDEWEB)

    O`Connor, M.; Schulz, J.; Tan, C. [Bechtel Power Corporation (United States)] [and others

    1995-02-01

    The AP600 Project is a passive pressurized water reactor power plant which is part of the Design Certification and First-of-a-Kind Engineering effort under the Advanced Light Water Reactor program. Included in this process is the design of the containment air filtration system which will be the subject of this paper. We will compare the practice used by previous plants with the AP600 approach to meet the goals of industry standards in sizing the containment air filtration system. The radiological aspects of design are of primary significance and will be the focus of this paper. The AP600 Project optimized the design to combine the functions of the high volumetric flow rate, low volumetric flow rate, and containment cleanup and other filtration systems into one multi-functional system. This achieves a more simplified, standardized, and lower cost design. Studies were performed to determine the possible concentrations of radioactive material in the containment atmosphere and the effectiveness of the purge system to keep concentrations within 10CFR20 limits and within offsite dose objectives. The concentrations were determined for various reactor coolant system leakage rates and containment purge modes of operation. The resultant concentrations were used to determine the containment accessibility during various stages of normal plant operation including refueling. The results of the parametric studies indicate that a dual train purge system with a capacity of 4,000 cfm per train is more than adequate to control the airborne radioactivity levels inside containment during normal plant operation and refueling, and satisfies the goals of ANSI/ANS-56.6-1986 and limits the amount of radioactive material released to the environment per ANSI/ANS 59.2-1985 to provide a safe environment for plant personnel and offsite residents.

  5. A MEMS-Based Flow Rate and Flow Direction Sensing Platform with Integrated Temperature Compensation Scheme

    Directory of Open Access Journals (Sweden)

    Chia-Yen Lee

    2009-07-01

    Full Text Available This study develops a MEMS-based low-cost sensing platform for sensing gas flow rate and flow direction comprising four silicon nitride cantilever beams arranged in a cross-form configuration, a circular hot-wire flow meter suspended on a silicon nitride membrane, and an integrated resistive temperature detector (RTD. In the proposed device, the flow rate is inversely derived from the change in the resistance signal of the flow meter when exposed to the sensed air stream. To compensate for the effects of the ambient temperature on the accuracy of the flow rate measurements, the output signal from the flow meter is compensated using the resistance signal generated by the RTD. As air travels over the surface of the cross-form cantilever structure, the upstream cantilevers are deflected in the downward direction, while the downstream cantilevers are deflected in the upward direction. The deflection of the cantilever beams causes a corresponding change in the resistive signals of the piezoresistors patterned on their upper surfaces. The amount by which each beam deflects depends on both the flow rate and the orientation of the beam relative to the direction of the gas flow. Thus, following an appropriate compensation by the temperature-corrected flow rate, the gas flow direction can be determined through a suitable manipulation of the output signals of the four piezoresistors. The experimental results have confirmed that the resulting variation in the output signals of the integrated sensors can be used to determine not only the ambient temperature and the velocity of the air flow, but also its direction relative to the sensor with an accuracy of ± 7.5o error.

  6. A MEMS-Based Flow Rate and Flow Direction Sensing Platform with Integrated Temperature Compensation Scheme.

    Science.gov (United States)

    Ma, Rong-Hua; Wang, Dung-An; Hsueh, Tzu-Han; Lee, Chia-Yen

    2009-01-01

    This study develops a MEMS-based low-cost sensing platform for sensing gas flow rate and flow direction comprising four silicon nitride cantilever beams arranged in a cross-form configuration, a circular hot-wire flow meter suspended on a silicon nitride membrane, and an integrated resistive temperature detector (RTD). In the proposed device, the flow rate is inversely derived from the change in the resistance signal of the flow meter when exposed to the sensed air stream. To compensate for the effects of the ambient temperature on the accuracy of the flow rate measurements, the output signal from the flow meter is compensated using the resistance signal generated by the RTD. As air travels over the surface of the cross-form cantilever structure, the upstream cantilevers are deflected in the downward direction, while the downstream cantilevers are deflected in the upward direction. The deflection of the cantilever beams causes a corresponding change in the resistive signals of the piezoresistors patterned on their upper surfaces. The amount by which each beam deflects depends on both the flow rate and the orientation of the beam relative to the direction of the gas flow. Thus, following an appropriate compensation by the temperature-corrected flow rate, the gas flow direction can be determined through a suitable manipulation of the output signals of the four piezoresistors. The experimental results have confirmed that the resulting variation in the output signals of the integrated sensors can be used to determine not only the ambient temperature and the velocity of the air flow, but also its direction relative to the sensor with an accuracy of ± 7.5° error.

  7. 49 CFR 193.2517 - Purging.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Purging. 193.2517 Section 193.2517 Transportation...: FEDERAL SAFETY STANDARDS Operations § 193.2517 Purging. When necessary for safety, components that could accumulate significant amounts of combustible mixtures must be purged in accordance with a procedure...

  8. Recovery of nitrogen and light hydrocarbons from polyalkene purge gas

    Science.gov (United States)

    Zwilling, Daniel Patrick; Golden, Timothy Christoph; Weist, Jr., Edward Landis; Ludwig, Keith Alan

    2003-06-10

    A method for the separation of a gas mixture comprises (a) obtaining a feed gas mixture comprising nitrogen and at least one hydrocarbon having two to six carbon atoms; (b) introducing the feed gas mixture at a temperature of about 60.degree. F. to about 105.degree. F. into an adsorbent bed containing adsorbent material which selectively adsorbs the hydrocarbon, and withdrawing from the adsorbent bed an effluent gas enriched in nitrogen; (c) discontinuing the flow of the feed gas mixture into the adsorbent bed and depressurizing the adsorbent bed by withdrawing depressurization gas therefrom; (d) purging the adsorbent bed by introducing a purge gas into the bed and withdrawing therefrom an effluent gas comprising the hydrocarbon, wherein the purge gas contains nitrogen at a concentration higher than that of the nitrogen in the feed gas mixture; (e) pressurizing the adsorbent bed by introducing pressurization gas into the bed; and (f) repeating (b) through (e) in a cyclic manner.

  9. The web as platform: Data flows in social media

    NARCIS (Netherlands)

    Helmond, A.

    2015-01-01

    This dissertation looks into the history of Web 2.0 as "the web as platform" (O’Reilly 2004) and traces the transition of social network sites into social media platforms to examine how social media has transformed the web. In order to understand this process from an infrastructural perspective, I

  10. The web as platform: Data flows in social media

    NARCIS (Netherlands)

    Helmond, A.

    2015-01-01

    This dissertation looks into the history of Web 2.0 as "the web as platform" (O’Reilly 2004) and traces the transition of social network sites into social media platforms to examine how social media has transformed the web. In order to understand this process from an infrastructural perspective, I d

  11. Thermal vacuum chamber repressurization with instrument purging

    Science.gov (United States)

    Woronowicz, Michael S.

    2016-09-01

    At the conclusion of cryogenic vacuum testing of the James Webb Space Telescope Optical Telescope Element Integrated Science Instrument Module (JWST-OTIS) in NASA Johnson Space Center's (JSCs) thermal vacuum (TV) Chamber A, contamination control (CC) engineers are postulating that chamber particulate material stirred up by the repressurization process may be kept from falling into the Integrated Science Instrument Module (ISIM) interior to some degree by activating instrument purge flows over some initial period before opening the chamber valves. This manuscript describes development of a series of models designed to describe this process. The models are strung together in tandem with a fictitious set of conditions to estimate overpressure evolution from which net outflow velocity behavior may be obtained. Creeping flow assumptions are then used to determine the maximum particle size that may be kept suspended above the ISIM aperture, keeping smaller particles from settling within the instrument module.

  12. Thermal Vacuum Chamber Repressurization with Instrument Purging

    Science.gov (United States)

    Woronowicz, Michael

    2017-01-01

    At the end of James Webb Space Telescope (JWST) OTIS (Optical Telescope Element-OTE-Integrated Science Instrument Module-ISIM) cryogenic vacuum testing in NASA Johnson Space Centers (JSCs) thermal vacuum (TV) Chamber A, contamination control (CC) engineers are mooting the idea that chamber particulate material stirred up by the repressurization process may be kept from falling into the ISIM interior to some degree by activating instrument purge flows over some initial period before opening the chamber valves. This memo describes development of a series of models designed to describe this process. These are strung together in tandem to estimate overpressure evolution from which net outflow velocity behavior may be obtained. Creeping flow assumptions are then used to determine the maximum particle size that may be kept suspended above the ISIM aperture, keeping smaller particles from settling within the instrument module.

  13. Leakage predictions for Rayleigh-step, helium-purge seals

    Science.gov (United States)

    Proctor, Margaret P.

    1988-01-01

    Rayleigh-step, helium purge, annular shaft seals, studied for use in liquid oxygen turbopumps, generate a hydrodynamic force that enables the seal to follow shaft perturbations. Hence, smaller clearances can be used to reduce seal leakage. FLOWCAL, a computer code developed by Mechanical Technology Incorporated, predicts gas flow rate through an annular seal with an axial pressure gradient. Analysis of a 50-mm Rayleigh-step, helium-purge, annular seal showed the flow rate increased axial pressure gradient, downstream pressure, and eccentricity ratio. Increased inlet temperature reduced leakage. Predictions made at maximum and minimum clearances (due to centrifugal and thermal growths, machining tolerances and + or - 2 percent uncertainty in the clearance measurement) placed wide boundaries on expected flow rates. The widest boundaries were set by thermal growth conditions. Predicted flow rates for a 50-mm Rayleigh-step, helium-purge, annular seal underestimated measured flow rates by three to seven times. However, the analysis did accurately predict flow rates for choked gas flow through annular seals when compared to flow rates measured in two other independent studies.

  14. ANALYSIS OF PENTACHLOROPHENOL IN WATER BY PURGE AND TRAP CONCENTRATOR COUPLED TOGAS CHROMATOGRAPHY

    Institute of Scientific and Technical Information of China (English)

    Huixia Lan; Yuancai Chen; Zhonghao Chen

    2004-01-01

    It is convenient and time saving to analyze pentachlorophenol (PCP) in water by purge and trap concentrator coupled to gas chromatography that avoids employing a great deal of organic solvent: In this paper, the appropriate purge and trap conditions of PCP are determined: the trapped sorbent is TenaxGC; the purge gas is pure nitrogen and purge flow is 40ml/min; the purge time is 30min. A series of standard PCP water samples 5, 10, 50, 100, 200,400, 800, 1000ppb are analyzed in order to obtain standard curve, and the linear regressive equation obtained is Y=109.65X-687.72, which correlation coefficient r is 0.9949. The precision of the method is determined with 0.5ppb PCP water sample, and the standard deviation measured is 3%. The detection limit for PCP is 0.2ppb.

  15. ANALYSIS OF PENTACHLOROPHENOL IN WATER BY PURGE AND TRAP CONCENTRATOR COUPLED TO GAS CHROMATOGRAPHY

    Institute of Scientific and Technical Information of China (English)

    HuixiaLan; YuancaiChen; ZhonghaoChen

    2004-01-01

    It is convenient and time saving to analyze pentachlorophenol (PCP) in water by purge and trap concentrator coupled to gas chromatography that avoids employing a great deal of organic solvent. In this paper, the appropriate purge and trap conditions of PCP are determined: the trapped sorbent is TenaxGC; the purge gas is pure nitrogen and purge flow is 40ml/min; the purge time is 30min. A series of standard PCP water samples 5, 10, 50, 100, 200, 400, 800, 1000ppb are analyzed in order to obtain standard curve, and the linear regressive equation obtained is Y=109.65X-687.72, which correlation coefficient r is 0.9949. The precision of the method is determined with 0.5ppb PCP water sample, and the standard deviation measured is 3%. The detection limit for PCP is 0.2ppb.

  16. Solute transport in a well under slow-purge and no-purge conditions

    Science.gov (United States)

    Plummer, M. A.; Britt, S. L.; Martin-Hayden, J. M.

    2010-12-01

    Non-purge sampling techniques, such as diffusion bags and in-situ sealed samplers, offer reliable and cost-effective groundwater monitoring methods that are a step closer to the goal of real-time monitoring without pumping or sample collection. Non-purge methods are, however, not yet completely accepted because questions remain about how solute concentrations in an unpurged well relate to concentrations in the adjacent formation. To answer questions about how undisturbed well water samples compare to formation concentrations, and to provide the information necessary to interpret results from non-purge monitoring systems, we have conducted a variety of physical experiments and numerical simulations of flow and transport in and through monitoring wells under low-flow and ambient flow conditions. Previous studies of flow and transport in wells used a Darcy’s law - based continuity equation for flow, which is often justified under the strong, forced-convection flow caused by pumping or large vertical hydraulic potential gradients. In our study, we focus on systems with weakly forced convection, where density-driven free convection may be of similar strength. We therefore solved Darcy’s law for porous media domains and the Navier Stokes equations for flow in the well, and coupled solution of the flow equations to that of solute transport. To illustrate expected in-well transport behavior under low-flow conditions, we present results of three particular studies: (1) time-dependent effluent concentrations from a well purged at low-flow pumping rates, (2) solute-driven density effects in a well under ambient horizontal flow and (3) temperature-driven mixing in a shallow well subject to seasonal temperature variations. Results of the first study illustrate that assumptions about the nature of in-well flow have a significant impact on effluent concentration curves even during pumping, with Poiseuille-type flow producing more rapid removal of concentration differences

  17. Anode purge strategy optimization of the polymer electrode membrane fuel cell system under the dead-end anode operation

    Science.gov (United States)

    Hu, Zhe; Yu, Yi; Wang, Guangjin; Chen, Xuesong; Chen, Pei; Chen, Jun; Zhou, Su

    2016-07-01

    Dead-ended anode (DEA) mode is commonly applied in fuel cell vehicles for the hydrogen purge at the anode side, to reduce fuel waste and enhance fuel cell efficiency. Anode purge is necessary and is definitely important with respect to removing liquid water and accumulated nitrogen in the gas diffusion layer and the flow field of the DEA-mode fuel cell. In this paper, the effect of different purge strategies on the stack performance and system efficiency is investigated experimentally using fast data acquisition and advanced tools, such as the fast cell voltage measurement (CVM) system and the mass spectrum. From the fast data acquisition, the voltage stability, liquid water and nitrogen concentration measurement in the anode exhaust are compared and analyzed under different purge strategy designs and using different purge valves. The results show that under the optimal purge strategy, the DEA fuel cell stack can achieve the desired stability and system efficiency based on the analysis of the cell voltage and purge volume. Moreover, the diameter of the purge valve has a great impact on the voltage stability because a diameter change will result in a different pressure drop and purge volume when the purge valve is open.

  18. Preparation and analysis of helium purge gas mixture to be used in Tritium Extraction System of LLCB TBM

    Science.gov (United States)

    Gayathri Devi, V.; Yadav, Deepak; Sircar, Amit

    2017-04-01

    Hydrogen isotopes are extracted from the Ceramic Breeder (CB) and liquid Lead Lithium (Pb-Li) breeder of Lead Lithium Ceramic Breeder (LLCB) Test Blanket Module (TBM) with Helium purge gas. 1000 ppm of hydrogen gas is mixed with the purge helium gas to facilitate improved extraction of hydrogen isotopes from the breeder zones by hydrogen swamping reactions [1]. An experimental set up is developed for making up the purge gas mixture with a composition similar to the purge gas composition to be used for extraction of hydrogen isotopes from CB and Pb-Li of LLCB TBM. This is achieved by introducing different ppm levels (1000 - 5000 ppm) of hydrogen in helium gas by flow control mechanism. The analysis of the purge gas mixture is performed using a highly sensitive Gas Chromatography (GC) system. This paper describes the detailed design of the experimental set-up and results for the analysis of different concentrations of hydrogen in helium purge gas.

  19. Purge water minimization at LEHR

    Energy Technology Data Exchange (ETDEWEB)

    Schalla, R.

    1996-11-01

    The field demonstration described in this report is being conducted as part of the Environmental Restoration Program at the Laboratory for Energy-Related Health Research (LEHR). The Environmental Restoration Program is one of several U.S. Department of Energy (DOE) waste cleanup projects designed to support by the actual use of emerging environmental management and restoration technologies. As part of an ongoing technical support mission to achieve excellence and efficiency in environmental restoration activities at LEHR, DOE requested Pacific Northwest National Laboratory`s (PNNL`s) guidance to identify the most efficient way of reducing purge water extracted by sampling pumps while still obtaining representative samples from LEHR monitoring wells.

  20. The Medical Complications Associated with Purging

    Science.gov (United States)

    Forney, K. Jean; Buchman-Schmitt, Jennifer M.; Keel, Pamela K.; Frank, Guido K.W.

    2015-01-01

    Objective Purging behaviors, including self-induced vomiting, laxative abuse, and diuretic abuse, are present across many of the eating disorders. Here we review the major medical complications of these behaviors. Method Although we identified over 100 scholarly articles describing medical complications associated with purging, most papers involved case studies or small, uncontrolled samples. Given the limited evidence base, we conducted a qualitative (rather than systematic) review to identify medical complications that have been attributed to purging behaviors. Results Medical conditions affecting the teeth, esophagus, gastrointestinal system, kidneys, skin, cardiovascular system, and musculoskeletal system were identified, with self-induced vomiting causing the most medical complications. Conclusions Purging behavior can be associated with severe medical complications across all body systems. Mental health professionals should refer patients with purging behaviors to medical providers for screening and treatment as needed. The medical work-up for individuals with eating disorders should include a comprehensive metabolic panel, complete blood count, and a full body exam including the teeth to prevent severe complications. Medical providers should screen patients for purging behaviors and associated medical complications, even in the absence of an eating disorder diagnosis, to increase the detection of eating disorders. Recognizing the link between purging and medical complications can aid in identifying potential eating disorders, particularly those that often elude detection such as purging disorder. PMID:26876429

  1. Selective purge for hydrogenation reactor recycle loop

    Science.gov (United States)

    Baker, Richard W.; Lokhandwala, Kaaeid A.

    2001-01-01

    Processes and apparatus for providing improved contaminant removal and hydrogen recovery in hydrogenation reactors, particularly in refineries and petrochemical plants. The improved contaminant removal is achieved by selective purging, by passing gases in the hydrogenation reactor recycle loop or purge stream across membranes selective in favor of the contaminant over hydrogen.

  2. Architecture Design and Experimental Platform Demonstration of Optical Network based on OpenFlow Protocol

    Science.gov (United States)

    Xing, Fangyuan; Wang, Honghuan; Yin, Hongxi; Li, Ming; Luo, Shenzi; Wu, Chenguang

    2016-02-01

    With the extensive application of cloud computing and data centres, as well as the constantly emerging services, the big data with the burst characteristic has brought huge challenges to optical networks. Consequently, the software defined optical network (SDON) that combines optical networks with software defined network (SDN), has attracted much attention. In this paper, an OpenFlow-enabled optical node employed in optical cross-connect (OXC) and reconfigurable optical add/drop multiplexer (ROADM), is proposed. An open source OpenFlow controller is extended on routing strategies. In addition, the experiment platform based on OpenFlow protocol for software defined optical network, is designed. The feasibility and availability of the OpenFlow-enabled optical nodes and the extended OpenFlow controller are validated by the connectivity test, protection switching and load balancing experiments in this test platform.

  3. Origin of deep lava flows at the base of the Galápagos Platform

    Science.gov (United States)

    Anderson, M.; Wanless, V. D.; Fornari, D. J.; Soule, S. A.; Jones, M.

    2016-12-01

    Side-scan sonar maps of the seafloor at the leading edge of Galápagos platform indicate regions of highly reflective seafloor that have been interpreted as large individual lava flows up to 30 km in length. However, the source for these long flows and whether they represent a single eruptive event is not known. The inferred proximal and distal ends of two lava flows were sampled using the Ocean Exploration Trust remotely operated vehicle (ROV) Hercules on the R/V Nautilus (research cruise #064) in the summer of 2015. In total, 25 basalt samples were collected and measured for major and trace element contents and radiogenic isotope ratios to determine if these uncharacteristically long lava flows are indeed individual eruptive units. Basaltic samples collected from the eastern and western ends of the long flows have distinct major and trace element contents. The western, downslope ends of both lava flows have similar trace element ratios, with La/Yb ranging from 9.2 to 9.7. By contrast, samples collected from the eastern, upslope end of the flow (closest to the platform) have lower La/Yb ratios from 4.8 to 5.7. Additionally, lavas from the western flow ends have lower MgO concentrations (4.2-5.4 wt%) compared to lavas from eastern flow ends (5.1-10.0 wt%). This is inconsistent with the flows forming from a homogeneous magma and suggests that the long lava flows are comprised of several different flow units. We suggest that the higher trace element ratios observed in samples collected from the western edge of the flows represent lower extents of melting at the leading edge of the Galápagos mantle plume, while the eastern, upslope flows have undergone higher extents of melting similar to those erupted at Fernandina volcano.

  4. Catalytic membrane reactor for tritium extraction system from He purge

    Energy Technology Data Exchange (ETDEWEB)

    Santucci, Alessia, E-mail: alessia.santucci@enea.it [ENEA for EUROfusion, Via E. Fermi 45, 00044 Frascati, Roma (Italy); Incelli, Marco [ENEA for EUROfusion, Via E. Fermi 45, 00044 Frascati, Roma (Italy); DEIM, University of Tuscia, Via del Paradiso 47, 01100 Viterbo (Italy); Sansovini, Mirko; Tosti, Silvano [ENEA for EUROfusion, Via E. Fermi 45, 00044 Frascati, Roma (Italy)

    2016-11-01

    Highlights: • In the HCBB blanket, the produced tritium is recovered by purging with helium; membrane technologies are able to separate tritium from helium. • The paper presents the results of two experimental campaigns. • In the first, a Pd–Ag diffuser for hydrogen separation is tested at several operating conditions. • In the second, the ability of a Pd–Ag membrane reactor for water decontamination is assessed by performing isotopic swamping and water gas shift reactions. - Abstract: In the Helium Cooled Pebble Bed (HCPB) blanket concept, the produced tritium is recovered purging the breeder with helium at low pressure, thus a tritium extraction system (TES) is foreseen to separate the produced tritium (which contains impurities like water) from the helium gas purge. Several R&D activities are running in parallel to experimentally identify most promising TES technologies: particularly, Pd-based membrane reactors (MR) are under investigation because of their large hydrogen selectivity, continuous operation capability, reliability and compactness. The construction and operation under DEMO relevant conditions (that presently foresee a He purge flow rate of about 10,000 Nm{sup 3}/h and a H{sub 2}/He ratio of 0.1%) of a medium scale MR is scheduled for next year, while presently preliminary experiments on a small scale reactor are performed to identify most suitable operative conditions and catalyst materials. This work presents the results of an experimental campaign carried out on a Pd-based membrane aimed at measuring the capability of this device in separating hydrogen from the helium. Many operative conditions have been investigated by considering different He/H{sub 2} feed flow ratios, several lumen pressures and reactor temperatures. Moreover, the performances of a membrane reactor (composed of a Pd–Ag tube having a wall thickness of about 113 μm, length 500 mm and diameter 10 mm) in processing the water contained in the purge gas have been

  5. Crystallization of bovine insulin on a flow-free droplet-based platform

    Science.gov (United States)

    Chen, Fengjuan; Du, Guanru; Yin, Di; Yin, Ruixue; Zhang, Hongbo; Zhang, Wenjun; Yang, Shih-Mo

    2017-03-01

    Crystallization is an important process in the pharmaceutical manufacturing industry. In this work, we report a study to create the zinc-free crystals of bovine insulin on a flow-free droplet-based platform we previously developed. The benefit of this platform is its promise to create a single type of crystals under a simpler and more stable environment and with a high throughput. The experimental result shows that the bovine insulin forms a rhombic dodecahedra shape and the coefficient variation (CV) in the size of crystals is less than 5%. These results are very promising for the insulin production.

  6. Velocity bias induced by flow patterns around ADCPs and associated deployment platforms

    Science.gov (United States)

    Mueller, David S.

    2015-01-01

    Velocity measurements near the Acoustic Doppler Current Profiler (ADCP) are important for mapping surface currents, measuring velocity and discharge in shallow streams, and providing accurate estimates of discharge in the top unmeasured portion of the water column. Improvements to ADCP performance permit measurement of velocities much closer (5 cm) to the transducer than has been possible in the past (25 cm). Velocity profiles collected by the U.S. Geological Survey (USGS) with a 1200 kHz Rio Grande Zedhead ADCP in 2002 showed a negative bias in measured velocities near the transducers. On the basis of these results, the USGS initiated a study combining field, laboratory, and numerical modeling data to assess the effect of flow patterns caused by flow around the ADCP and deployment platforms on velocities measured near the transducers. This ongoing study has shown that the negative bias observed in the field is due to the flow pattern around the ADCP. The flow pattern around an ADCP violates the basic assumption of flow homogeneity required for an accurate three-dimensional velocity solution. Results, to date (2014), have indicated velocity biases within the measurable profile, due to flow disturbance, for the TRDI 1200 kHz Rio Grande Zedhead and the SonTek RiverSurveyor M9 ADCPs. The flow speed past the ADCP, the mount and the deployment platform have also been shown to play an important role in the magnitude and extent of the velocity bias.

  7. A microfluidic platform with a flow-balanced fluidic network for osteoarthritis diagnosis

    Science.gov (United States)

    Kim, Kangil; Park, Yoo Min; Yoon, Hyun C.; Yang, Sang Sik

    2013-05-01

    Osteoarthritis (OA) is one of the most common human diseases, and the occurrence of OA is likely to increase with the increase of population ages. The diagnosis of OA is based on patientrelevant measures, structural measures, and measurement of biomarkers that are released through joint metabolism. Traditionally, radiography or magnetic resonance imaging (MRI) is used to diagnose OA and predict its course. However, diagnostic imaging in OA provides only indirect information on pathology and treatment response. A sensing of OA based on the detection of biomarkers insignificantly improves the accuracy and sensitivity of diagnosis and reduces the cost compared with that of radiography or MRI. In our former study, we proposed microfluidic platform to detect biomarker of OA. But the platform can detect only one biomarker because it has one microfluidic channel. In this report, we proposes microfluidic platform that can detect several biomarkers. The proposed platform has three layers. The bottom layer has gold patterns on a Si substrate for optical sensing. The middle layer and top layer were fabricated by polydimethysiloxane (PDMS) using soft-lithography. The middle layer has four channels connecting top layer to bottom layer. The top layer consists of one sample injection inlet, and four antibody injection inlets. To this end, we designed a flow-balanced microfluidic network using analogy between electric and hydraulic systems. Also, the designed microfluidic network was confirmed by finite element model (FEM) analysis using COMSOL FEMLAB. To verify the efficiency of fabricated platform, the optical sensing test was performed to detect biomarker of OA using fluorescence microscope. We used cartilage oligomeric matrix protein (COMP) as biomarker because it reflects specific changes in joint tissues. The platform successfully detected various concentration of COMP (0, 100, 500, 1000 ng/ml) at each chamber. The effectiveness of the microfluidic platform was verified

  8. Purging dissolved oxygen by nitrogen bubble aeration

    Science.gov (United States)

    Yamashita, Tatsuya; Ando, Keita

    2016-11-01

    We apply aeration with nitrogen microbubbles to water in order to see whether oxygen gas originally dissolved in the water at one atmosphere is purged by the aeration. The concentration of dissolved oxygen (DO) is detected by a commercial DO meter. To detect the dissolved nitrogen (DN) level, we observe the growth of millimetre-sized bubbles nucleated at glass surfaces in contact with the aerated water and compare it with the Epstein-Plesset theory that accounts for DO/DN diffusions and the presence of the glass surfaces. Comparisons between the experiment and the theory suggest that the DO in the water are effectively purged by the aeration.

  9. Evaluation of Variable Refrigerant Flow Systems Performance on Oak Ridge National Laboratory s Flexible Research Platform: Part 3 Simulation Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Im, Piljae [ORNL; Cho, Heejin [Mississippi State University (MSU); Kim, Dongsu [Mississippi State University (MSU); Cox, Sam [Mississippi State University (MSU)

    2016-08-01

    This report provides second-year project simulation results for the multi-year project titled “Evaluation of Variable Refrigeration Flow (VRF) system on Oak Ridge National Laboratory (ORNL)’s Flexible Research Platform (FRP).”

  10. Argon purge gas cooled by chill box

    Science.gov (United States)

    Spiro, L. W.

    1966-01-01

    Cooling argon purge gas by routing it through a shop-fabricated chill box reduces charring of tungsten inert gas torch head components. The argon gas is in a cooled state as it enters the torch and prevents buildup of char caused by the high concentrations of heat in the weld area during welding operations.

  11. Size-controlled flow synthesis of gold nanoparticles using a segmented flow microfluidic platform.

    Science.gov (United States)

    Cabeza, Victor Sebastian; Kuhn, Simon; Kulkarni, Amol A; Jensen, Klavs F

    2012-05-01

    Segmented flow is often used in the synthesis of nanomaterials to achieve narrow particle size distribution. The narrowness of the distribution is commonly attributed to the reduced dispersion associated with segmented flows. On the basis of the analysis of flow fields and the resulting particle size distribution, we demonstrate that it is the slip velocity between the two fluids and internal mixing in the continuous-phase slugs that govern the nature of the particle size distribution. The reduction in the axial dispersion has less impact on particle growth and hence on the particle size distribution. Synthesis of gold nanoparticles from HAuCl(4) with rapid reduction by NaBH(4) serves as a model system. Rapid reduction yields gold nuclei, which grow by agglomeration, and it is controlled by the interaction of the nuclei with local flow. Thus, the difference in the physical properties of the two phases and the inlet flow rates ultimately control the particle growth. Hence, a careful choice of continuous and dispersed phases is necessary to control the nanoparticle size and size distribution.

  12. Variability in bacteria and virus-like particle abundances during purging of unconfined aquifers.

    Science.gov (United States)

    Roudnew, Ben; Lavery, Trish J; Seymour, Justin R; Jeffries, Thomas C; Mitchell, James G

    2014-01-01

    Standard methodologies for sampling the physicochemical conditions of groundwater recommend purging a bore for three bore volumes to avoid sampling the stagnant water within a bore and instead gain samples representative of the aquifer. However, there are currently no methodological standards addressing the amount of purging required to gain representative biological samples to assess groundwater bacterial and viral abundances. The objective of this study was to examine how bacterial and viral abundances change during the purging of bore volumes. Six bores infiltrating into unconfined aquifers were pumped for five or six bore volumes each and bacteria and virus-like particles (VLPs) were enumerated from each bore volume using flow cytometry. In examination of the individual bores trends in bacterial abundances were observed to increase, decrease, or remain constant with each purged bore volume. Furthermore, triplicates taken at each bore volume indicated substantial variations in VLP and bacterial abundances that are often larger than the differences between bore volumes. This indicates a high level of small scale heterogeneity in microbial community abundance in groundwater samples, and we suggest that this may be an intrinsic feature of bore biology. The heterogeneity observed may be driven by bottom up processes (variability in the distribution of organic and inorganic nutrients), top-down processes (grazing and viral lysis), physical heterogeneities in the bore, or technical artifacts associated with the purging process. We suggest that a more detailed understanding of the ecology underpinning this variability is required to adequately describe the microbiological characteristics of groundwater ecosystems.

  13. 49 CFR 193.2615 - Isolating and purging.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Isolating and purging. 193.2615 Section 193.2615...: FEDERAL SAFETY STANDARDS Maintenance § 193.2615 Isolating and purging. (a) Before personnel begin... component must be purged in accordance with a procedure which meets the requirements of AGA...

  14. Dynamic control of aerodynamic forces on a moving platform using active flow control

    Science.gov (United States)

    Brzozowski, Daniel P.

    The unsteady interaction between trailing edge aerodynamic flow control and airfoil motion in pitch and plunge is investigated in wind tunnel experiments using a two degree-of-freedom traverse which enables application of time-dependent external torque and forces by servo motors. The global aerodynamic forces and moments are regulated by controlling vorticity generation and accumulation near the trailing edge of the airfoil using hybrid synthetic jet actuators. The dynamic coupling between the actuation and the time-dependent flow field is characterized using simultaneous force and particle image velocimetry (PIV) measurements that are taken phase-locked to the commanded actuation waveform. The effect of the unsteady motion on the model-embedded flow control is assessed in both trajectory tracking and disturbance rejection maneuvers. The time-varying aerodynamic lift and pitching moment are estimated from a PIV wake survey using a reduced order model based on classical unsteady aerodynamic theory. These measurements suggest that the entire flow over the airfoil readjusts within 2--3 convective time scales, which is about two orders of magnitude shorter than the characteristic time associated with the controlled maneuver of the wind tunnel model. This illustrates that flow-control actuation can be typically effected on time scales that are commensurate with the flow's convective time scale, and that the maneuver response is primarily limited by the inertia of the platform.

  15. Ecogeomorphic Properties of Flood-ebb Flows on a Coastal North Carolina Salt-marsh Platform

    Science.gov (United States)

    Howell, S.; Furbish, D.; Mudd, S.

    2006-12-01

    Salt marsh ecosystems play a vital role in nutrient processing, shoreline defense, and as habitats for commercially important species. Along the Albemarle and Pamlico Sounds, North Carolina, where the tidal amplitude ranges from 1.0 to 1.5 m, salt marsh communities are expected to undergo a transition from intertidal marshes to subtidal habitats in response to sea-level rise and associated increases in inundation and possibly tidal range. Intertidal areas along the back-barrier sound of Bogue Banks feature well developed networks of tidal channels and exhibit classic macrophyte zonation, with Spartina spp. residing along lower elevations and Juncus roemerianus at higher elevations. As part of a long-term study of macrophyte dynamics, sedimentation and geomorphology in the Albemarle and Pamlico Sounds area, here we describe the pattern of flood-ebb flow on a marsh platform. Continuous measurements from a set of pressure transducers arranged along a marsh transect are used to describe spatial variations in the frequency, duration and depth of inundation as a function of platform elevation, macrophyte biomass, and proximity to the tidal creek. Stem density and diameter of Spartina alterniflora and Juncus roemerianus affect the magnitude of drag forces on the marsh platform during flooding; our field measurements are used to constrain the relationship between macrophyte stand characteristics and these drag forces.

  16. Femtosecond laser fabrication of fiber based optofluidic platform for flow cytometry applications

    Science.gov (United States)

    Serhatlioglu, Murat; Elbuken, Caglar; Ortac, Bulend; Solmaz, Mehmet E.

    2017-02-01

    Miniaturized optofluidic platforms play an important role in bio-analysis, detection and diagnostic applications. The advantages of such miniaturized devices are extremely low sample requirement, low cost development and rapid analysis capabilities. Fused silica is advantageous for optofluidic systems due to properties such as being chemically inert, mechanically stable, and optically transparent to a wide spectrum of light. As a three dimensional manufacturing method, femtosecond laser scanning followed by chemical etching shows great potential to fabricate glass based optofluidic chips. In this study, we demonstrate fabrication of all-fiber based, optofluidic flow cytometer in fused silica glass by femtosecond laser machining. 3D particle focusing was achieved through a straightforward planar chip design with two separately fabricated fused silica glass slides thermally bonded together. Bioparticles in a fluid stream encounter with optical interrogation region specifically designed to allocate 405nm single mode fiber laser source and two multi-mode collection fibers for forward scattering (FSC) and side scattering (SSC) signals detection. Detected signal data collected with oscilloscope and post processed with MATLAB script file. We were able to count number of events over 4000events/sec, and achieve size distribution for 5.95μm monodisperse polystyrene beads using FSC and SSC signals. Our platform shows promise for optical and fluidic miniaturization of flow cytometry systems.

  17. Air riding seal with purge cavity

    Energy Technology Data Exchange (ETDEWEB)

    Sexton, Thomas D; Mills, Jacob A

    2017-08-15

    An air riding seal for a turbine in a gas turbine engine, where an annular piston is axial moveable within an annular piston chamber formed in a stator of the turbine and forms a seal with a surface on the rotor using pressurized air that forms a cushion in a pocket of the annular piston. A purge cavity is formed on the annular piston and is connected to a purge hole that extends through the annular piston to a lower pressure region around the annular piston or through the rotor to an opposite side. The annular piston is sealed also with inner and outer seals that can be a labyrinth seal to form an additional seal than the cushion of air in the pocket to prevent the face of the air riding seal from overheating.

  18. Purging of untrustworthy recommendations from a grid

    CERN Document Server

    Kumar, P Suresh; Ramachandram, S

    2012-01-01

    In grid computing, trust has massive significance. There is lot of research to propose various models in providing trusted resource sharing mechanisms. The trust is a belief or perception that various researchers have tried to correlate with some computational model. Trust on any entity can be direct or indirect. Direct trust is the impact of either first impression over the entity or acquired during some direct interaction. Indirect trust is the trust may be due to either reputation gained or recommendations received from various recommenders of a particular domain in a grid or any other domain outside that grid or outside that grid itself. Unfortunately, malicious indirect trust leads to the misuse of valuable resources of the grid. This paper proposes the mechanism of identifying and purging the untrustworthy recommendations in the grid environment. Through the obtained results, we show the way of purging of untrustworthy entities.

  19. Well purge and sample apparatus and method

    Science.gov (United States)

    Schalla, Ronald; Smith, Ronald M.; Hall, Stephen H.; Smart, John E.; Gustafson, Gregg S.

    1995-01-01

    The present invention specifically permits purging and/or sampling of a well but only removing, at most, about 25% of the fluid volume compared to conventional methods and, at a minimum, removing none of the fluid volume from the well. The invention is an isolation assembly with a packer, pump and exhaust, that is inserted into the well. The isolation assembly is designed so that only a volume of fluid between the outside diameter of the isolation assembly and the inside diameter of the well over a fluid column height from the bottom of the well to the top of the active portion (lower annulus) is removed. The packer is positioned above the active portion thereby sealing the well and preventing any mixing or contamination of inlet fluid with fluid above the packer. Ports in the wall of the isolation assembly permit purging and sampling of the lower annulus along the height of the active portion.

  20. EVALUATION OF THREE-DIMENSIONAL NUMERICAL MODEL FOR SALINE INTRUSION AND PURGING IN SEWAGE OUTFALLS

    Institute of Scientific and Technical Information of China (English)

    WU Wei; YAN Zhong-min

    2007-01-01

    Saline intrusion into sewage outfalls will greatly decrease the efficiency of the structures. The numerical model for this flow has been limited to one- and two-dimensional ones. In this article, a three-dimensional numerical model for saline intrusion and purging in sewage outfalls was developed. The flow was modeled in three dimensions under turbulent conditions with the RNG turbulence model. The numerical results provided quantitative evidence of the fundamental flow mechanisms that took place during saline intrusion and purging. The comparisons of the results with that of two-dimensional model and that of experiments indicate that the three-dimensional numerical model developed in this article is more effective in predicting the internal flow in outfalls.

  1. Flow cytometric scoring of micronucleated erythrocytes: an efficient platform for assessing in vivo cytogenetic damage.

    Science.gov (United States)

    Dertinger, Stephen D; Torous, Dorothea K; Hayashi, Makoto; MacGregor, James T

    2011-01-01

    The relative simplicity of the micronucleated erythrocyte endpoint has made it amenable to automated scoring approaches. Flow cytometry is one such scoring platform that has been employed successfully. This review describes the evolution and properties of flow cytometry-based scoring of micronucleated erythrocytes. The methodology has become widely applied to rodent blood specimens and the high throughput nature of the technology provides a number of advantages over manual microscopic scoring. For instance, the ability to efficiently survey many dose levels and many more cells per specimen relative to microscopy benefits studies that are designed to identify no observable effect levels or lowest observable effect levels. Furthermore, flow cytometry makes it practical to study species with low spontaneous reticulocyte (RET) counts and micronucleus (MN) frequencies, thereby facilitating integration of blood-based micronucleated reticulocyte (MN-RET) frequency measurements into experiments conducted across species of toxicological interest. This capability enhances genotoxicity assessments that have historically been made in dedicated MN tests performed in one species. Importantly, the feasibility of using MN-RET frequencies in blood from humans as an index of genetic damage in bone marrow opens a critical area of application that had not been practical previously. We conclude with recommendations for additional work that is needed to more fully realise the potential of flow cytometric in vivo MN scoring.

  2. A multi-platform flow device for microbial (co- cultivation and microscopic analysis.

    Directory of Open Access Journals (Sweden)

    Matthijn C Hesselman

    Full Text Available Novel microbial cultivation platforms are of increasing interest to researchers in academia and industry. The development of materials with specialized chemical and geometric properties has opened up new possibilities in the study of previously unculturable microorganisms and has facilitated the design of elegant, high-throughput experimental set-ups. Within the context of the international Genetically Engineered Machine (iGEM competition, we set out to design, manufacture, and implement a flow device that can accommodate multiple growth platforms, that is, a silicon nitride based microsieve and a porous aluminium oxide based microdish. It provides control over (co-culturing conditions similar to a chemostat, while allowing organisms to be observed microscopically. The device was designed to be affordable, reusable, and above all, versatile. To test its functionality and general utility, we performed multiple experiments with Escherichia coli cells harboring synthetic gene circuits and were able to quantitatively study emerging expression dynamics in real-time via fluorescence microscopy. Furthermore, we demonstrated that the device provides a unique environment for the cultivation of nematodes, suggesting that the device could also prove useful in microscopy studies of multicellular microorganisms.

  3. Quantitative data analysis methods for bead-based DNA hybridization assays using generic flow cytometry platforms.

    Science.gov (United States)

    Corrie, S R; Lawrie, G A; Battersby, B J; Ford, K; Rühmann, A; Koehler, K; Sabath, D E; Trau, M

    2008-05-01

    Bead-based assays are in demand for rapid genomic and proteomic assays for both research and clinical purposes. Standard quantitative procedures addressing raw data quality and analysis are required to ensure the data are consistent and reproducible across laboratories independent of flow platform. Quantitative procedures have been introduced spanning raw histogram analysis through to absolute target quantitation. These included models developed to estimate the absolute number of sample molecules bound per bead (Langmuir isotherm), relative quantitative comparisons (two-sided t-tests), and statistical analyses investigating the quality of raw fluorescence data. The absolute target quantitation method revealed a concentration range (below probe saturation) of Cy5-labeled synthetic cytokeratin 19 (K19) RNA of c.a. 1 x 10(4) to 500 x 10(4) molecules/bead, with a binding constant of c.a. 1.6 nM. Raw hybridization frequency histograms were observed to be highly reproducible across 10 triplex assay replicates and only three assay replicates were required to distinguish overlapping peaks representing small sequence mismatches. This study provides a quantitative scheme for determining the absolute target concentration in nucleic acid hybridization reactions and the equilibrium binding constants for individual probe/target pairs. It is envisaged that such studies will form the basis of standard analytical procedures for bead-based cytometry assays to ensure reproducibility in inter- and intra-platform comparisons of data between laboratories. (c) 2008 International Society for Advancement of Cytometry.

  4. Assessment of methylprednisolone purging efficacy on Daudi burkitt lymphoma cells from normal bone marrow.

    Science.gov (United States)

    Janakiraman, N; Niewenhuis, L M

    1991-01-01

    Studies on normal bone marrow and Daudi Burkitt lymphoma cells were performed to determine the efficacy of selective, in vitro chemopurging with methylprednisolone (MP). We found that MP reduces the number of lymphoma cells without significant damage to bone marrow cells. This information is important because we need to improve the existing in vitro purging regimens used to cleanse autologous marrows of metastatic disease before transplantation into cancer patients who have received high-dose chemotherapy. Normal human bone marrow (NBM) and Daudi lymphoma cells were treated in parallel with various purging regimens, NBM death was evaluated using soft-agar culture, while Daudi cell death was evaluated using one-week liquid culture. A protocol of 2.0 mg/mL of MP for four hours demonstrated optimal selectivity. When treatment was followed by cryopreservation, a 1.7 log purge of Daudi cells was increased to 2.3 logs while preserving 36% of committed NBM precursors. We repeated these experiments on a simulated contaminated marrow to model closely the mixture of normal and malignant cells found in advanced, metastatic disease. We evaluated this mixed system by flow cytometric immunoanalysis using the two-color CD10/CD20 markers to detect residual, viable Daudi cells. Our initial results were reproducible in this mixed-cell system, further supporting the evidence for effective in vitro purging of bone marrow using MP.

  5. Three-dimensional flow in the Florida platform: Theoretical analysis of Kohout convection at its type locality

    Science.gov (United States)

    Hughes, Joseph D.; Vacher, H. L.; Sanford, Ward E.

    2007-07-01

    Kohout convection is the name given to the circulation of saline groundwater deep within carbonate platforms, first proposed by F.A. Kohout in the 1960s for south Florida. It is now seen as an Mg pump for dolomitization by seawater. As proposed by Kohout, cold seawater is drawn into the Florida platform from the deep Straits of Florida as part of a geothermally driven circulation in which the seawater then rises in the interior of the platform to mix and exit with the discharging meteoric water of the Floridan aquifer system. Simulation of the asymmetrically emergent Florida platform with the new three-dimensional (3-D), finite-element groundwater flow and transport model SUTRA-MS, which couples salinity- and temperature-dependent density variations, allows analysis of how much of the cyclic flow is due to geothermal heating (free convection) as opposed to mixing with meteoric water discharging to the shoreline (forced convection). Simulation of the system with and without geothermal heating reveals that the inflow of seawater from the Straits of Florida would be similar without the heat flow, but the distribution would differ significantly. The addition of heat flow reduces the asymmetry of the circulation: it decreases seawater inflows on the Atlantic side by 8% and on the Gulf of Mexico side by half. The study illustrates the complex interplay of freshwater-saltwater mixing, geothermal heat flow, and projected dolomitization in complicated 3-D settings with asymmetric boundary conditions and realistic horizontal and vertical variations in hydraulic properties.

  6. CoreFlow: a computational platform for integration, analysis and modeling of complex biological data.

    Science.gov (United States)

    Pasculescu, Adrian; Schoof, Erwin M; Creixell, Pau; Zheng, Yong; Olhovsky, Marina; Tian, Ruijun; So, Jonathan; Vanderlaan, Rachel D; Pawson, Tony; Linding, Rune; Colwill, Karen

    2014-04-04

    A major challenge in mass spectrometry and other large-scale applications is how to handle, integrate, and model the data that is produced. Given the speed at which technology advances and the need to keep pace with biological experiments, we designed a computational platform, CoreFlow, which provides programmers with a framework to manage data in real-time. It allows users to upload data into a relational database (MySQL), and to create custom scripts in high-level languages such as R, Python, or Perl for processing, correcting and modeling this data. CoreFlow organizes these scripts into project-specific pipelines, tracks interdependencies between related tasks, and enables the generation of summary reports as well as publication-quality images. As a result, the gap between experimental and computational components of a typical large-scale biology project is reduced, decreasing the time between data generation, analysis and manuscript writing. CoreFlow is being released to the scientific community as an open-sourced software package complete with proteomics-specific examples, which include corrections for incomplete isotopic labeling of peptides (SILAC) or arginine-to-proline conversion, and modeling of multiple/selected reaction monitoring (MRM/SRM) results. CoreFlow was purposely designed as an environment for programmers to rapidly perform data analysis. These analyses are assembled into project-specific workflows that are readily shared with biologists to guide the next stages of experimentation. Its simple yet powerful interface provides a structure where scripts can be written and tested virtually simultaneously to shorten the life cycle of code development for a particular task. The scripts are exposed at every step so that a user can quickly see the relationships between the data, the assumptions that have been made, and the manipulations that have been performed. Since the scripts use commonly available programming languages, they can easily be

  7. An Integrated microfluidic platform for liquid droplet in gas flow generation with in liquid flow collection and manipulation

    Science.gov (United States)

    Tirandazi, Pooyan; Hidrovo, Carlos H.

    2016-11-01

    Discretization of biological samples and chemical reactions within digital droplets is a powerful technique which has rapidly emerged in many biochemical syntheses. The ability to generate, manipulate, and monitor millions of microdroplets in a short time provides great potential for high throughput screening and detection in microbiology. Here we report a microfluidic device for the formation of uniform microdroplets (50 μm-100 μm) using a high speed gas as the continuous phase. Gas-borne droplets are generated in a chip-based flow-focusing device fabricated in PDMS, and travel along the gaseous microchannel and are subsequently captured within a second liquid phase. The droplets are then transferred and collected in a minichamber and move into the manipulation section for further processing operations on the drops. All these steps are performed automatically in a single multilayer chip. This integrated microfluidic platform for generation, collection, and manipulation of the droplets provides great opportunities for monitoring and detection of gas-analytes. Utilizing the generated picoliter airborne droplets feature lower reaction times and higher transfer rates as compared to conventional air sampling techniques. Thus, it can greatly facilitate the investigation of airborne analytes by interrogation of the digital droplets using different analytical techniques. Furthermore, the presented liquid-in-gas generation method can be utilized for production of oil-free microparticles and microcapsules used in the food industry and for drug delivery.

  8. Does haplodiploidy purge inbreeding depression in rotifer populations?

    Directory of Open Access Journals (Sweden)

    Ana M Tortajada

    Full Text Available BACKGROUND: Inbreeding depression is an important evolutionary factor, particularly when new habitats are colonized by few individuals. Then, inbreeding depression by drift could favour the establishment of later immigrants because their hybrid offspring would enjoy higher fitness. Rotifers are the only major zooplanktonic group where information on inbreeding depression is still critically scarce, despite the fact that in cyclical parthenogenetic rotifers males are haploid and could purge deleterious recessive alleles, thereby decreasing inbreeding depression. METHODOLOGY/PRINCIPAL FINDINGS: We studied the effects of inbreeding in two populations of the cyclical parthenogenetic rotifer Brachionus plicatilis. For each population, we compared both the parental fertilization proportion and F1 fitness components from intraclonal (selfed and interclonal (outcrossed crosses. The parental fertilization proportion was similar for both types of crosses, suggesting that there is no mechanism to avoid selfing. In the F1 generation of both populations, we found evidence of inbreeding depression for the fitness components associated with asexual reproduction; whereas inbreeding depression was only found for one of the two sexual reproduction fitness components measured. CONCLUSIONS/SIGNIFICANCE: Our results show that rotifers, like other major zooplanktonic groups, can be affected by inbreeding depression in different stages of their life cycle. These results suggest that haplodiploidy does not purge efficiently deleterious recessive alleles. The inbreeding depression detected here has important implications when a rotifer population is founded and intraclonal crossing is likely to occur. Thus, during the foundation of new populations inbreeding depression may provide opportunities for new immigrants, increasing gene flow between populations, and affecting genetic differentiation.

  9. Pressure-control purge panel for automatic butt welding

    Science.gov (United States)

    Lang, E. J.; Van Wagner, B. H.

    1969-01-01

    Modification of a purge panel for use in an automatic butt weld reduces the drop in pressure between the regulators and the weld head and tube purge fitting. The invention affects air regulators for plants, regulating circuits for pneumatic valves, and automatic welding machines.

  10. Microflow1, a sheathless fiber-optic flow cytometry biomedical platform: demonstration onboard the international space station.

    Science.gov (United States)

    Dubeau-Laramée, Geneviève; Rivière, Christophe; Jean, Isabelle; Mermut, Ozzy; Cohen, Luchino Y

    2014-04-01

    A fiber-optic based flow cytometry platform was designed to build a portable and robust instrument for space applications. At the core of the Microflow1 is a unique fiber-optic flow cell fitted to a fluidic system and fiber coupled to the source and detection channels. A Microflow1 engineering unit was first tested and benchmarked against a commercial flow cytometer as a reference in a standard laboratory environment. Testing in parabolic flight campaigns was performed to establish Microflow1's performance in weightlessness, before operating the new platform on the International Space Station. Microflow1 had comparable performances to commercial systems, and operated remarkably and robustly in weightlessness (microgravity). Microflow1 supported immunophenotyping as well as microbead-based multiplexed cytokine assays in the space environment and independently of gravity levels. Results presented here provide evidence that this fiber-optic cytometer technology is inherently compatible with the space environment with negligible compromise to analytical performance.

  11. Three-dimensional flow in the Florida platform: Theoretical analysis of Kohout convection at its type locality

    Science.gov (United States)

    Hughes, J.D.; Vacher, H.L.; Sanford, W.E.

    2007-01-01

    Kohout convection is the name given to the circulation of saline groundwater deep within carbonate platforms, first proposed by F.A. Kohout in the 1960s for south Florida. It is now seen as an Mg pump for dolomitization by seawater. As proposed by Kohout, cold seawater is drawn into the Florida platform from the deep Straits of Florida as part of a geothermally driven circulation in which the seawater then rises in the interior of the platform to mix and exit with the discharging meteoric water of the Floridan aquifer system. Simulation of the asymmetrically emergent Florida platform with the new three-dimensional (3-D), finite-element groundwater flow and transport model SUTRA-MS, which couples salinity- and temperature-dependent density variations, allows analysis of how much of the cyclic flow is due to geothermal heating (free convection) as opposed to mixing with meteoric water discharging to the shoreline (forced convection). Simulation of the system with and without geothermal heating reveals that the inflow of seawater from the Straits of Florida would be similar without the heat flow, but the distribution would differ significantly. The addition of heat flow reduces the asymmetry of the circulation: it decreases seawater inflows on the Atlantic side by 8% and on the Guff of Mexico side by half. The study illustrates the complex interplay of freshwater-saltwater mixing, geothermal heat flow, and projected dolomitization in complicated 3-D settings with asymmetric boundary conditions and realistic horizontal and vertical variations in hydraulic properties. ?? 2007 The Geological Society of America.

  12. Molds in Brined Cucumbers: Cause of Softening During Air-Purging of Fermentations †

    Science.gov (United States)

    Costilow, Ralph N.; Gates, Karen; Lacy, Melvyn L.

    1980-01-01

    Softening of cucumbers in fermentations purged at high air-flow rates was caused by molds growing in the brined cucumbers, not in the brine. This conclusion is based on the following results: (i) no microorganisms were isolated in significant numbers from brines that caused softening of pasteurized brined cucumbers, (ii) no pectinolytic enzyme activities were produced in cucumber brines in the absence of cucumbers, (iii) the pickles in some air-purged fermentations became very soft without the appearance of any pectinolytic enzyme activity in the brine, (iv) mold hyphae were consistently observed in tissues of soft pickles, (v) molds consistently developed in cultures of slices of surface sterilized cucumbers taken from fermentations in which soft pickles were subsequently found, and (vi) molds belonging to the genera Alternaria, Fusarium, and Mucor isolated from slices all softened pasteurized brined cucumbers. Images PMID:16345619

  13. Comprehensive Study of the Flow Control Strategy in a Wirelessly Charged Centrifugal Microfluidic Platform with Two Rotation Axes.

    Science.gov (United States)

    Zhu, Yunzeng; Chen, Yiqi; Meng, Xiangrui; Wang, Jing; Lu, Ying; Xu, Youchun; Cheng, Jing

    2017-09-05

    Centrifugal microfluidics has been widely applied in the sample-in-answer-out systems for the analyses of nucleic acids, proteins, and small molecules. However, the inherent characteristic of unidirectional fluid propulsion limits the flexibility of these fluidic chips. Providing an extra degree of freedom to allow the unconstrained and reversible pumping of liquid is an effective strategy to address this limitation. In this study, a wirelessly charged centrifugal microfluidic platform with two rotation axes has been constructed and the flow control strategy in such platform with two degrees of freedom was comprehensively studied for the first time. Inductively coupled coils are installed on the platform to achieve wireless power transfer to the spinning stage. A micro servo motor is mounted on both sides of the stage to alter the orientation of the device around a secondary rotation axis on demand during stage rotation. The basic liquid operations on this platform, including directional transport of liquid, valving, metering, and mixing, are comprehensively studied and realized. Finally, a chip for the simultaneous determination of hexavalent chromium [Cr(VI)] and methanal in water samples is designed and tested based on the strategy presented in this paper, demonstrating the potential use of this platform for on-site environmental monitoring, food safety testing, and other life science applications.

  14. Space Station Environmental Control and Life Support System Purge Control Pump Assembly Modeling and Analysis

    Science.gov (United States)

    Schunk, R. Gregory; Hunt, Patrick L. (Technical Monitor)

    2001-01-01

    Preliminary results from a thermal/flow analysis of the Purge Control Pump Assembly (PCPA) indicate that pump performance (mass flow rate) is enhanced via cooling of the housing and lowering of the inlet vapor quality. Under a nominal operational profile (25% duty cycle or less), at the maximum motor dissipation, it appears that the peristaltic tubing temperature will still remain significantly below the expected UPA condenser temperature (78 F max versus approximately 105 F in the condenser) permitting condensation in the pump head.

  15. Verification of the ASTM G-124 Purge Equation

    Science.gov (United States)

    Robbins, Katherine E.; Davis, Samuel Eddie

    2009-01-01

    ASTM G-124 seeks to evaluate combustion characteristics of metals in high-purity (greater than 99%) oxygen atmospheres. ASTM G-124 provides the following equation to determine the minimum number of purges required to reach this level of purity in a test chamber: n = -4/log10(Pa/Ph), where "n" is the total number of purge cycles required, Ph is the absolute pressure used for the purge on each cycle and Pa is the atmospheric pressure or the vent pressure. The origin of this equation is not known and has been the source of frequent questions as to its accuracy and reliability. This paper shows the derivation of the G-124 purge equation, and experimentally explores the equation to determine if it accurately predicts the number of cycles required.

  16. A dangerous combination of binge and purge.

    Science.gov (United States)

    Culkin, Alison; Gabe, Simon M; Peake, Simon T C; Stern, Julian M

    2012-03-01

    We present a 36-year-old female diagnosed with Crohn's disease at the age of 11 years. In 2001, she underwent a total colectomy and further small bowel resection as a result of active Crohn's. Her residual anatomy consisted of 150 cm of small bowel to an end jejunostomy. Subsequently, she developed short bowel syndrome with recurrent episodes of hypomagnesaemia, hypocalcaemia, and hypokalaemia. Dietetic assessment revealed her to be severely underweight at 37 kg with a bodymass index (BMI) of 14.4 kg/m(2) . During her admission, our patient underwent psychiatric assessment and was established on home parenteral nutrition (HPN). At the time of discharge, 1 month later, her weight had increased to 44 kg (BMI = 17.7 kg/m(2) ). Over the following 12-month period, she lost weight (BMI, 15.4 mg/m(2) ; weight, 39.5 kg) and she described a high stoma output (up to 17 L) and dehydration. Assessment of her oral intake found she was consuming an estimated 14,000 kcal and 600 g protein per day. At this time, the possibility of a new form of eating disorder was discussed with the patient and she agreed that her behavior i.e., using her stoma as a purging device, fulfilled the criteria for a diagnosis of bulimia nervosa and she was referred to a specialist eating disorder unit.

  17. A Point-of-Need infrared mediated PCR platform with compatible lateral flow strip for HPV detection.

    Science.gov (United States)

    Liu, Wenjia; Zhang, Mingfang; Liu, Xiaoyan; Sharma, Alok; Ding, Xianting

    2017-10-15

    With the increasing need of monitoring the epidemiology of serious infectious diseases, food hygiene, food additives and pesticide residues, it is urgent to develop portable, easy-to-use, inexpensive and rapid molecular diagnostic tools. Herein, we demonstrate a prototype of IR mediated Conducting Oil and CarbOn Nanotube circUlaTing PCR (IR-COCONUT PCR) platform for nucleic acid amplification. The presented platform offers a new solution for miniaturized PCR instruments with non-contact heaters by using conducting oil and carbon nanotube as a medium in IR mediated PCR. This novel platform offers accurate and flexible control of temperature through the integration of PID (proportional-integral-derivative) algorithms to manipulate the duty cycle of the voltage signals of IR LED and a peristaltic pump. The ramping rate of the introduced platform in current study is 1.5°C/s for heating speed and -2.0°C/s for cooling speed. This platform fulfills 30 thermal cycles within 50min which is a match to the conventional bench-top PCR thermo cyclers. For demonstration purpose, human papillomavirus (HPV) patient cervical swab specimens were examined. Downstream lateral flow strip (LFS) was also developed to quantity the PCR products from the IR-COCONUT PCR device within 25min. This PCR platform together with the compatible LFS shows great potential for in-field and Point-of-Need (PoN) testing of genetic or contagious diseases. Copyright © 2017 Elsevier B.V. All rights reserved.

  18. Multiplex immunoassay for persistent organic pollutants in tilapia: Comparison of imaging- and flow cytometry-based platforms using spectrally encoded paramagnetic microspheres

    Science.gov (United States)

    Recent developments in spectrally encoded microspheres (SEMs)-based technologies provide high multiplexing possibilities. Most SEMs-based assays required a flow cytometer with sophisticated fluidics and optics. The new imaging superparamagnetic SEMs-based platform transports SEMs with considerably ...

  19. Early Holocene High Magnitude Debris Flow Events and Environmental Change as Illustrated by the Moxi Platform, Hengduan Mountains, SW China

    Institute of Scientific and Technical Information of China (English)

    ZHANG Junyan; CHENG Genwei; LI Yongfei

    2006-01-01

    Thick debris flow deposits in the Hengduan Mountains of southwestern China record landscape instability at the close of the last glaciation and in the early Holocene. The deposits, ranging in thickness from 100 to 200 m, are common and in high magnitude in the valleys of this region. They are products of large debris flows induced by glacier and enabled by the presence of large amount of glacial debris on the landscape. The carbon 14 dating from Moxi Platform indicates that a period of catastrophic debris flows occurred at c. 7 kyr B.P., and was concurrent with other glacial-fluvial fans and terraces which tied to regional climatic oscillations elsewhere in the Himalaya. The comparable events suggest a strong climatic control on earth surface processes for the dynamics, magnitude, and frequency in this region.

  20. A Multi-Platform Flow Device for Microbial (Co-) Cultivation and Microscopic Analysis

    NARCIS (Netherlands)

    Hesselman, M.C.; Odoni, D.I.; Ryback, B.M.; Groot, de S.; Heck, van R.G.A.; Keijsers, J.; Kolkman, P.; Nieuwenhuijse, D.; Nuland, Y.M.; Sebus, E.; Spee, R.; Vries, de H.; Wapenaar, M.T.; Ingham, C.J.; Schroen, K.; Martins Dos Santos, V.A.P.; Spaans, S.K.; Hugenholtz, F.; Passel, van M.W.J.

    2012-01-01

    Novel microbial cultivation platforms are of increasing interest to researchers in academia and industry. The development of materials with specialized chemical and geometric properties has opened up new possibilities in the study of previously unculturable microorganisms and has facilitated the des

  1. The pro-Franco purge of the primary teaching profession

    Directory of Open Access Journals (Sweden)

    Juan Manuel FERNÁNDEZ SORIA

    2013-11-01

    Full Text Available The purge of primary school teaching profession, like other groups, was an instrument of political repression organized and planned in order to establish, keep and legitimise the social-political «New Order» that aroze after the victory of Franco's army. There are three points to this article. The first point establishes the state of the question on the repressive nature and conditions in Franco's Spain. The repression adopted against the school teachers has its own quality: it is more preventive than punitive, trying with it to dissuade the pedagogue action of the teaching profession, a group who never had the confidence of the new regime nor the ideological mainstays which support it, including the catolical church. The second point tries to clear this mistrust, which goes back to the times of the Spanish Second Republic; in this mistrust the purge of the schoolteachers has its arguments. The third part studies the purge of Valencian schoolteachers, and analyses its political and social characteristics, concluding that an apolitical and scantily compromised group is purged essentially due to political accusations. Though the accusations were not harsh we can confirm the hypothesis of the preventive purge of the teaching profession, a group the Franco regime needed but kept by fear. The great lozers of this repression were not only the school teachers but the Spanish society itself. A society that saw how the new pedagogy under Franco's regime cut the progress that was finally underway only a few years prior.

  2. Aerodynamic Flow Control by Thermoacoustic Excitation from the Constituent Nanomaterials on the Platform Surface

    Science.gov (United States)

    2016-02-01

    control, turbulence, fluid mechanics, nonlinear coupling, planar jet experiment, Director’s Research Initiative (DRI) 16. SECURITY CLASSIFICATION OF...Successful development of active aerodynamic flow control technologies that delay or prevent separation could lead to substantial performance...improvements, including increased speed, maneuverability, payload capacity, and/or range. However, instances in which active flow control technologies have

  3. Inbreeding depression is purged in the invasive insect Harmonia axyridis.

    Science.gov (United States)

    Facon, Benoît; Hufbauer, Ruth A; Tayeh, Ashraf; Loiseau, Anne; Lombaert, Eric; Vitalis, Renaud; Guillemaud, Thomas; Lundgren, Jonathan G; Estoup, Arnaud

    2011-03-08

    Bottlenecks in population size reduce genetic diversity and increase inbreeding, which can lead to inbreeding depression. It is thus puzzling how introduced species, which typically pass through bottlenecks, become such successful invaders. However, under certain theoretical conditions, bottlenecks of intermediate size can actually purge the alleles that cause inbreeding depression. Although this process has been confirmed in model laboratory systems, it has yet to be observed in natural invasive populations. We evaluate whether such purging could facilitate biological invasions by using the world-wide invasion of the ladybird (or ladybug) Harmonia axyridis. We first show that invasive populations endured a bottleneck of intermediate intensity. We then demonstrate that replicate introduced populations experience almost none of the inbreeding depression suffered by native populations. Thus, rather than posing a barrier to invasion as often assumed, bottlenecks, by purging deleterious alleles, can enable the evolution of invaders that maintain high fitness even when inbred. Copyright © 2011 Elsevier Ltd. All rights reserved.

  4. Two-dimensional hydrodynamic flow focusing in a microfluidic platform featuring a monolithic integrated glass micronozzle

    Science.gov (United States)

    Liu, Yifan; Shen, Yusheng; Duan, Lian; Yobas, Levent

    2016-10-01

    Two-dimensional hydrodynamic flow focusing is demonstrated through a microfluidic device featuring a monolithic integrated glass micronozzle inside a flow-focusing geometry. Such a coaxial configuration allows simple one-step focusing of a sample fluid stream, jetted from the micronozzle tip, in both in-plane and out-of-plane directions. The width of the focused filament can be precisely controlled and further scaled down to the submicrometer regime to facilitate rapid hydrodynamic mixing. Fluorescence quenching experiments reveal ultra-fast microsecond mixing of the denaturant into the focused filament. This device offers new possibilities to a set of applications such as the study of protein folding kinetics.

  5. Propellant and Purge System Contamination "2007: A Summer of Fun"

    Science.gov (United States)

    Galloway, Randy

    2010-01-01

    This slide presentation reviews the propellant and purge system contamination that occurred during the summer of 2007 at Stennis Space Center. During this period Multiple propellant/pressurant system contamination events prompted a thorough investigation, the results of which are reviewed.

  6. Well-purging criteria for sampling purgeable organic compounds

    Science.gov (United States)

    Gibs, J.; Imbrigiotta, T.E.

    1990-01-01

    The results indicate that 1) purgeable organic compound concentrations stabilized when three casing volume were purged in only 55% of the cases evaluated in this study, 2) purgeable organic compounds concentrations did not consistently follow the temporal variation of, nor stabilize at the same time as, the measure field characteristics, and 3) purging to achieve hydraulic equilibrium between casing and aquifer water consistently underestimated the time and casing volumes needed to achieve stable values of water-quality measurements in highly transmissive aquifers. The conclusion from these data is that none of the previously recommended criteria for purging a well can be applied reliably to collecting a "representative' sample of purgeable organic compounds. These results indicate that the criteria for purging a well prior to sampling for purgeable organic compounds must take into account other factors, such as the unique hydrogeologic characteristics of a site, the nature and extent of purgeable organic compounds present, and areal extent of the contamination, the well construction, and the sampling objectives of the investigation. -from Authors

  7. Critical role of a pre-purge setup in the thermal desorption analysis of volatile organic compounds by gas chromatography with mass spectrometry.

    Science.gov (United States)

    Kim, Yong-Hyun; Kim, Ki-Hyun

    2015-07-01

    In general, volatile organic compounds in ambient air are quantified by following a well-defined standard calibration procedure using a gas-/liquid-phase standard. If the liquid standard is analyzed by a thermal desorption, the solvent effect is unavoidable through the alteration of breakthrough properties or retention times. To learn more about the variables of the thermal desorption-based analysis, the effect of pre-purge conditions was evaluated for 18 volatile organic compounds with different types of sorbent tube materials by fixing standard volume (1 μL) and flow rate (100 mL/min). The gas phase calibration was also carried out as reference for the non-solvent effect. A single tube filled with Tenax TA exhibited the least solvent effect with the short pre-purge (1 min), while being subject to the breakthrough at or above 10 min pre-purge. For a three-bed sorbent tube with Carboxen 1000, at least 10 min of pre-purge was needed for the compounds with a retention time close to methanol (e.g., propanal). Another three-bed tube with Carbopack X reduced the solvent effect efficiently for a short pre-purge (2 min) without the breakthrough. As such, the solvent effect can be adjusted by the proper control of the sorbent tube application.

  8. Purging behavior in anorexia nervosa and eating disorder not otherwise specified

    DEFF Research Database (Denmark)

    Støving, René Klinkby; Andries, Alin; Brixen, Kim Torsten

    2012-01-01

    Purging behavior in eating disorders is associated with medical risks. We aimed to compare remission rates in purging and non-purging females with anorexia nervosa (AN) and eating disorder not otherwise specified (EDNOS) in a large retrospective single center cohort. A total of 339 patients...

  9. MACRO- MICRO-PURGE SOIL GAS SAMPLING METHODS FOR THE COLLECTION OF CONTAMINANT VAPORS

    Science.gov (United States)

    Purging influence on soil gas concentrations for volatile organic compounds (VOCs), as affected by sampling tube inner diameter and sampling depth (i.e., dead-space purge volume), was evaluated at different field sites. A macro-purge sampling system consisted of a standard hollo...

  10. CoreFlow: A computational platform for integration, analysis and modeling of complex biological data

    DEFF Research Database (Denmark)

    Pasculescu, Adrian; Schoof, Erwin; Creixell, Pau

    2014-01-01

    between data generation, analysis and manuscript writing. CoreFlow is being released to the scientific community as an open-sourced software package complete with proteomics-specific examples, which include corrections for incomplete isotopic labeling of peptides (SILAC) or arginine-to-proline conversion...... provides programmers with a framework to manage data in real-time. It allows users to upload data into a relational database (MySQL), and to create custom scripts in high-level languages such as R, Python, or Perl for processing, correcting and modeling this data. CoreFlow organizes these scripts...... into project-specific pipelines, tracks interdependencies between related tasks, and enables the generation of summary reports as well as publication-quality images. As a result, the gap between experimental and computational components of a typical large-scale biology project is reduced, decreasing the time...

  11. Modeling and simulation of ammonia removal from purge gases of ammonia plants using a catalytic Pd-Ag membrane reactor.

    Science.gov (United States)

    Rahimpour, M R; Asgari, A

    2008-05-01

    In this work, the removal of ammonia from synthesis purge gas of an ammonia plant has been investigated. Since the ammonia decomposition is thermodynamically limited, a membrane reactor is used for complete decomposition. A double pipe catalytic membrane reactor is used to remove ammonia from purge gas. The purge gas is flowing in the reaction side and is converted to hydrogen and nitrogen over nickel-alumina catalyst. The hydrogen is transferred through the Pd-Ag membrane of tube side to the shell side. A mathematical model including conservation of mass in the tube and shell side of reactor is proposed. The proposed model was solved numerically and the effects of different parameters on the rector performance were investigated. The effects of pressure, temperature, flow rate (sweep ratio), membrane thickness and reactor diameter have been investigated in the present study. Increasing ammonia conversion was observed by raising the temperature, sweep ratio and reducing membrane thickness. When the pressure increases, the decomposition is gone toward completion but, at low pressure the ammonia conversion in the outset of reactor is higher than other pressures, but complete destruction of the ammonia cannot be achieved. The proposed model can be used for design of an industrial catalytic membrane reactor for removal of ammonia from ammonia plant and reducing NO(x) emissions.

  12. Design and implementation of fluidic micro-pulleys for flow control on centrifugal microfluidic platforms.

    Science.gov (United States)

    Soroori, Salar; Kulinsky, Lawrence; Kido, Horacio; Madou, Marc

    2014-06-01

    Microfluidic discs have been employed in a variety of applications for chemical analyses and biological diagnostics. These platforms offer a sophisticated fluidic toolbox, necessary to perform processes that involve sample preparation, purification, analysis, and detection. However, one of the weaknesses of such systems is the uni-directional movement of fluid from the disc center to its periphery due to the uni-directionality of the propelling centrifugal force. Here we demonstrate a mechanism for fluid movement from the periphery of a hydrophobic disc toward its center that does not rely on the energy supplied by any peripheral equipment. This method utilizes a ventless fluidic network that connects a column of working fluid to a sample fluid. As the working fluid is pushed by the centrifugal force to move toward the periphery of the disc, the sample fluid is pulled up toward the center of the disc analogous to a physical pulley where two weights are connected by a rope passed through a block. The ventless network is analogous to the rope in the pulley. As the working fluid descends, it creates a negative pressure that pulls the sample fluid up. The sample and working fluids do not come into direct contact and it allows the freedom to select a working fluid with physical properties markedly different from those of the sample. This article provides a demonstration of the "micro-pulley" on a disc, discusses underlying physical phenomena, provides design guidelines for fabrication of micro-pulleys on discs, and outlines a vision for future micro-pulley applications.

  13. Design of multilevel flow modelling-based decision support system by using multiagent platform

    DEFF Research Database (Denmark)

    Zhang, Xinxin; Lind, Morten; Ravn, Ole

    2015-01-01

    For complex engineering systems, there is an increasing demand forsafety and reliability. Decision support system (DSS) is designed to offersupervision and analysis about operational situations. A proper modelrepresentation is required for DSS to understand the process knowledge.Multilevel flow m...... available techniques of MFM reasoning and less matureyet relevant MFM concepts are considered. It also offers an architecture designof task organisation for MFM software tools by using the concept of agent andtechnology of multiagent software system......For complex engineering systems, there is an increasing demand forsafety and reliability. Decision support system (DSS) is designed to offersupervision and analysis about operational situations. A proper modelrepresentation is required for DSS to understand the process knowledge.Multilevel flow...... modelling (MFM) represents complex system in multiplelevels of means-end and part-whole decompositions, which is proposed in thispaper as basis for developing decision support systems. The aim of this paper isto explore the different possible functionalities by applying MFM to DSS,where both currently...

  14. An effective electrical sensing scheme using AC electrothermal flow on a biosensor platform based on a carbon nanotube network

    Science.gov (United States)

    Lee, Won Cheol; Lee, Hoseok; Lim, Jaeheung; Park, Young June

    2016-11-01

    We report a simple and efficient electrical sensing scheme that can be used to overcome the "diffusion limit" of affinity-based biosensors by incorporating the structural advantage of a concentric electrode biosensor platform and the microstirring effect of AC electrothermal flow (ACEF). To prove the effect of ACEF on the biosensor performance, we performed both simulations and experiments for the detection of cardiac troponin-I, which is a biomarker for acute myocardial infarction. The finite element simulation results indicate that AC bias to the electrode (which has a concentric structure in our device) can induce fast convection flow, which facilitates the transport of the target molecules to the binding region located between the two electrodes. In our device, the channel region made of a carbon nanotube network decorated with gold nanoparticles, which act as the attaching sites of the probe molecules, is used as a highly sensitive electrical channel. We find that the electrical sensing method exhibited extremely fast sensing speeds compared with those under no bias (diffusion-limited) conditions.

  15. Paper capillary force driven hollow channel as a platform for multiphase flows bioassays

    Directory of Open Access Journals (Sweden)

    Zheng Tengfei

    2016-05-01

    Full Text Available This paper develops a simple, inexpensive, and portable diagnostic assays that may be useful in remote settings, and in particular, in less industrialized countries where simple assays are becoming increasingly important for detecting disease and monitoring health. In this assays, the paper capillary force is first used to transport complex fluids such as whole blood or colloidal suspensions that contain particulates in a new type channel - paper capillary driven hollow channel, which offset the disadvantages of current paper microfluidic technologies. To demonstrate the various applications of the paper capillary force driven hollow channel, several devices are design and made to complete the purpose of exhibiting laminar flow in a T-junction microchannel, sheath a core stream in a three-inlet channel and transportation whole blood.

  16. Event-triggered logical flow control for comprehensive process integration of multi-step assays on centrifugal microfluidic platforms.

    Science.gov (United States)

    Kinahan, David J; Kearney, Sinéad M; Dimov, Nikolay; Glynn, Macdara T; Ducrée, Jens

    2014-07-01

    The centrifugal "lab-on-a-disc" concept has proven to have great potential for process integration of bioanalytical assays, in particular where ease-of-use, ruggedness, portability, fast turn-around time and cost efficiency are of paramount importance. Yet, as all liquids residing on the disc are exposed to the same centrifugal field, an inherent challenge of these systems remains the automation of multi-step, multi-liquid sample processing and subsequent detection. In order to orchestrate the underlying bioanalytical protocols, an ample palette of rotationally and externally actuated valving schemes has been developed. While excelling with the level of flow control, externally actuated valves require interaction with peripheral instrumentation, thus compromising the conceptual simplicity of the centrifugal platform. In turn, for rotationally controlled schemes, such as common capillary burst valves, typical manufacturing tolerances tend to limit the number of consecutive laboratory unit operations (LUOs) that can be automated on a single disc. In this paper, a major advancement on recently established dissolvable film (DF) valving is presented; for the very first time, a liquid handling sequence can be controlled in response to completion of preceding liquid transfer event, i.e. completely independent of external stimulus or changes in speed of disc rotation. The basic, event-triggered valve configuration is further adapted to leverage conditional, large-scale process integration. First, we demonstrate a fluidic network on a disc encompassing 10 discrete valving steps including logical relationships such as an AND-conditional as well as serial and parallel flow control. Then we present a disc which is capable of implementing common laboratory unit operations such as metering and selective routing of flows. Finally, as a pilot study, these functions are integrated on a single disc to automate a common, multi-step lab protocol for the extraction of total RNA from

  17. Hydrogel-coated feed spacers in two-phase flow cleaning in spiral wound membrane elements: A novel platform for eco-friendly biofouling mitigation

    NARCIS (Netherlands)

    Wibisono, Yusuf; Yandi, Wetra; Golabi, Mohsen; Nugraha, Roni; Cornelissen, Emile R.; Kemperman, Antoine J.B.; Ederth, Thomas; Nijmeijer, Kitty

    2015-01-01

    Biofouling is still a major challenge in the application of nanofiltration and reverse osmosis membranes. Here we present a platform approach for environmentally friendly biofouling control using a combination of a hydrogel-coated feed spacer and two-phase flow cleaning. Neutral (polyHEMA-co-PEG10MA

  18. Multiplex immunoassay for persistent organic pollutants in tilapia: comparison of imaging- and flow cytometry-based platforms using spectrally encoded paramagnetic microspheres

    NARCIS (Netherlands)

    Meimaridou, A.; Haasnoot, W.; Shelver, W.L.; Franek, M.; Nielen, M.W.F.

    2013-01-01

    Recent developments in spectrally encoded microspheres (SEMs)-based technologies provide high multiplexing possibilities. Most SEMs-based assays require a flow cytometer with sophisticated fluidics and optics. A new imaging super-paramagnetic SEMs-based alternative platform transports SEMs with cons

  19. Cell surface profiling using high-throughput flow cytometry: a platform for biomarker discovery and analysis of cellular heterogeneity.

    Directory of Open Access Journals (Sweden)

    Craig A Gedye

    Full Text Available Cell surface proteins have a wide range of biological functions, and are often used as lineage-specific markers. Antibodies that recognize cell surface antigens are widely used as research tools, diagnostic markers, and even therapeutic agents. The ability to obtain broad cell surface protein profiles would thus be of great value in a wide range of fields. There are however currently few available methods for high-throughput analysis of large numbers of cell surface proteins. We describe here a high-throughput flow cytometry (HT-FC platform for rapid analysis of 363 cell surface antigens. Here we demonstrate that HT-FC provides reproducible results, and use the platform to identify cell surface antigens that are influenced by common cell preparation methods. We show that multiple populations within complex samples such as primary tumors can be simultaneously analyzed by co-staining of cells with lineage-specific antibodies, allowing unprecedented depth of analysis of heterogeneous cell populations. Furthermore, standard informatics methods can be used to visualize, cluster and downsample HT-FC data to reveal novel signatures and biomarkers. We show that the cell surface profile provides sufficient molecular information to classify samples from different cancers and tissue types into biologically relevant clusters using unsupervised hierarchical clustering. Finally, we describe the identification of a candidate lineage marker and its subsequent validation. In summary, HT-FC combines the advantages of a high-throughput screen with a detection method that is sensitive, quantitative, highly reproducible, and allows in-depth analysis of heterogeneous samples. The use of commercially available antibodies means that high quality reagents are immediately available for follow-up studies. HT-FC has a wide range of applications, including biomarker discovery, molecular classification of cancers, or identification of novel lineage specific or stem cell

  20. Ashcroft Pressure Switch Monitor for Low SCHe Purge Pressure

    Energy Technology Data Exchange (ETDEWEB)

    VAN KATWIJK, C.

    2000-06-21

    These 0-15 psig pressure switches are located in the SCHe helium purge lines after PCV-5*23 and before PCV-5*27. The pressure switches monitor the pressure being maintained between the two PCVs and actuate on low pressure of 15 psig. This design is used for each of the SCHe supply lines (4). Electronic output signal is NON-SAFETY (GS).

  1. The Role of Loss of Control Eating in Purging Disorder

    Science.gov (United States)

    Forney, K. Jean; Haedt-Matt, Alissa A.; Keel, Pamela K.

    2014-01-01

    Objective Purging Disorder (PD), an Other Specified Feeding or Eating Disorder,1 is characterized by recurrent purging in the absence of binge eating. Though objectively large binge episodes are not present, individuals with PD may experience a loss of control (LOC) while eating a normal or small amounts of food. The present study sought to examine the role of LOC eating in PD using archival data from 101 women with PD. Method Participants completed diagnostic interviews and self-report questionnaires. Analyses examined the relationship between LOC eating and eating disorder features, psychopathology, personality traits, and impairment, in bivariate models and then in multivariate models controlling for purging frequency, age, and body mass index. Results Across bivariate and multivariate models, LOC eating frequency was associated with greater disinhibition around food, hunger, depressive symptoms, negative urgency, and distress and impairment. Discussion LOC eating is a clinically significant feature of PD and should be considered in future definitions of PD. Future research should examine whether LOC eating better represents a dimension of severity in PD or a specifier that may impact treatment response or course. PMID:24185981

  2. Efficient purging of deleterious mutations in plants with haploid selfing

    Energy Technology Data Exchange (ETDEWEB)

    Szovenyi, Peter [Univ. of Zurich (Switzerland); Shaw, Jon [Duke Univ., Durham, NC (United States); Yang, Xiaohan [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Devos, Nicolas [Duke Univ., Durham, NC (United States)

    2014-05-30

    In diploid organisms, selfing reduces the efficiency of selection in removing deleterious mutations from a population. This need not be the case for all organisms. Some plants, for example, undergo an extreme form of selfing known as intragametophytic selfing, which immediately exposes all recessive deleterious mutations in a parental genome to selective purging. Here we ask how effectively deleterious mutations are removed from such plants. Specifically, we study the extent to which deleterious mutations accumulate in a predominantly selfing and a predominantly outcrossing pair of moss species, using genome-wide transcriptome data. We find that the selfing species purge significantly more non-synonymous mutations, as well as a greater proportion of radical amino acid changes which alter physicochemical properties of amino acids. Moreover, their purging of deleterious mutation is especially strong in conserved regions of protein-coding genes. Our observations show that selfing need not impede but can even accelerate the removal of deleterious mutations, and do so on a genome-wide scale.

  3. Biofilm Removal Using Carbon Dioxide Aerosols without Nitrogen Purge.

    Science.gov (United States)

    Hong, Seongkyeol; Jang, Jaesung

    2016-11-06

    Biofilms can cause serious concerns in many applications. Not only can they cause economic losses, but they can also present a public health hazard. Therefore, it is highly desirable to remove biofilms from surfaces. Many studies on CO2 aerosol cleaning have employed nitrogen purges to increase biofilm removal efficiency by reducing the moisture condensation generated during the cleaning. However, in this study, periodic jets of CO2 aerosols without nitrogen purges were used to remove Pseudomonas putida biofilms from polished stainless steel surfaces. CO2 aerosols are mixtures of solid and gaseous CO2 and are generated when high-pressure CO2 gas is adiabatically expanded through a nozzle. These high-speed aerosols were applied to a biofilm that had been grown for 24 hr. The removal efficiency ranged from 90.36% to 98.29% and was evaluated by measuring the fluorescence intensity of the biofilm as the treatment time was varied from 16 sec to 88 sec. We also performed experiments to compare the removal efficiencies with and without nitrogen purges; the measured biofilm removal efficiencies were not significantly different from each other (t-test, p > 0.55). Therefore, this technique can be used to clean various bio-contaminated surfaces within one minute.

  4. Expandable Purge Chambers Would Protect Cryogenic Fittings

    Science.gov (United States)

    Townsend, Ivan I., III

    2004-01-01

    Expandable ice-prevention and cleanliness-preservation (EIP-CP) chambers have been proposed to prevent the accumulation of ice or airborne particles on quick-disconnect (QD) fittings, or on ducts or tubes that contain cryogenic fluids. In the original application for which the EIP-CP chambers were conceived, there is a requirement to be able to disconnect and reconnect the QD fittings in rapid succession. If ice were to form on the fittings by condensation and freezing of airborne water vapor on the cold fitting surfaces, the ice could interfere with proper mating of the fittings, making it necessary to wait an unacceptably long time for the ice to thaw before attempting reconnection. By keeping water vapor away from the cold fitting surfaces, the EIP-CP chambers would prevent accumulation of ice, preserving the ability to reconnect as soon as required. Basically, the role of an EIP-CP chamber would be to serve as an enclosure for a flow of dry nitrogen gas that would keep ambient air away from QD cryogenic fittings. An EIP-CP chamber would be an inflatable device made of a fabriclike material. The chamber would be attached to an umbilical plate holding a cryogenic QD fitting.

  5. A Complete Optical Sensor System Based on a POF-SPR Platform and a Thermo-Stabilized Flow Cell for Biochemical Applications.

    Science.gov (United States)

    Cennamo, Nunzio; Chiavaioli, Francesco; Trono, Cosimo; Tombelli, Sara; Giannetti, Ambra; Baldini, Francesco; Zeni, Luigi

    2016-02-04

    An optical sensor platform based on surface plasmon resonance (SPR) in a plastic optical fiber (POF) integrated into a thermo-stabilized flow cell for biochemical sensing applications is proposed. This device has been realized and experimentally tested by using a classic receptor-analyte assay. For this purpose, the gold surface of the POF was chemically modified through the formation of a self-assembling monolayer. The surface robustness of the POF-SPR platform has been tested for the first time thanks to the flow cell. The experimental results show that the proposed device can be successfully used for label-free biochemical sensing. The final goal of this work is to achieve a complete, small-size, simple to use and low cost optical sensor system. The whole system with the flow cell and the optical sensor are extensively described, together with the experimental results obtained with an immunoglobulin G (IgG)/anti-IgG assay.

  6. A Complete Optical Sensor System Based on a POF-SPR Platform and a Thermo-Stabilized Flow Cell for Biochemical Applications

    Directory of Open Access Journals (Sweden)

    Nunzio Cennamo

    2016-02-01

    Full Text Available An optical sensor platform based on surface plasmon resonance (SPR in a plastic optical fiber (POF integrated into a thermo-stabilized flow cell for biochemical sensing applications is proposed. This device has been realized and experimentally tested by using a classic receptor-analyte assay. For this purpose, the gold surface of the POF was chemically modified through the formation of a self-assembling monolayer. The surface robustness of the POF-SPR platform has been tested for the first time thanks to the flow cell. The experimental results show that the proposed device can be successfully used for label-free biochemical sensing. The final goal of this work is to achieve a complete, small-size, simple to use and low cost optical sensor system. The whole system with the flow cell and the optical sensor are extensively described, together with the experimental results obtained with an immunoglobulin G (IgG/anti-IgG assay.

  7. PEMFC cold-start performance after twice purge%二次吹扫条件下的PEMFC冷启动实验

    Institute of Scientific and Technical Information of China (English)

    罗马吉; 王芳芳; 刘威; 詹志刚

    2011-01-01

    通过使用干空气二次吹扫的方式对稳定工作后的质子交换膜燃料电池(PEMFC)单电池进行除水处理,考察了单电池经过吹扫除水操作后的除水量以及内阻变化过程,并研究了单电池经过吹扫除水处理后的常温启动性能以及-10℃下的冷启动性能.实验研究发现:单电池经过干空气二次吹扫处理后,可以在较短时间内经济有效地移除电池内的水,同时单电池的内阻升高.单电池经过干空气二次吹扫后常温启动性能下降,且随二次吹扫流量的增加而加剧,但未造成不可恢复的性能损失.适当的二次吹扫流量可以使电池成功冷启动.吹扫除水策略是优化PEMFC冷启动性能的关键因素之一.%Water in an operated proton exchange membrane fuel cell (PEMFC) was removed by twice purging with dry air. The weight of removed water and the process of resistance-change were investigated after the gas purging operation on the cell. The start-up performance of the cell in normal temperature and the cold start-up performance at -10 °C after purge were studied. The experimental results indicate that the water in a single cell can be removed in quite short time effectively and the cell electric resistance increase after twice purging. The start-up performance of the cells in normal temperature become deteriorated and get worse with the increased purging gas volume after twice purging, but the performance degradation can be recovered. Cold start-up of single cell can perform successfully by appropriate flow rate of twice purging. Purge strategy is one of the key points of optimizing fuel cell cold start-up performance.

  8. Evaluation of Capiox FX05 oxygenator with an integrated arterial filter on trapping gaseous microemboli and pressure drop with open and closed purge line.

    Science.gov (United States)

    Qiu, Feng; Peng, Sophia; Kunselman, Allen; Ündar, Akif

    2010-11-01

    Gaseous microemboli (GME) remain a challenge for cardiopulmonary bypass (CPB) because there is a positive correlation between microemboli exposure during CPB and postoperative neurological injury. Thus, minimizing the number of GME delivered to pediatric patients undergoing CPB procedures would lead to better clinical outcomes. In this study, we used a simulated CPB model to evaluate the effectiveness of capturing GME and the degree of membrane pressure drop for a new membrane oxygenator, Capiox Baby FX05 (Terumo Corporation,Tokyo, Japan), which has an integrated arterial filter with open and closed purge line.We used identical components in this study as our clinical CPB circuit. Three emboli detection and classification quantifier transducers were placed at prepump, preoxygenator, and postoxygenator sites in the circuit.Two flow probes as well as three pressure transducers were placed upstream and downstream of the oxygenator. The system was primed with human blood titrated to 30% hematocrit with Lactated Ringer’s solution.A bolus of air (1 mL) was injected in the prepump site under nonpulsatile perfusion mode at three flow rates (500,750, and 1000 mL/min) and with the purge line either open or closed. Six trials were performed for each unique set-up for a total of 36 trials.All trials were conducted at 35°C. The circuit pressure was kept constant at 100 mm Hg. Both the size and quantity of microemboli detected at postoxygenator site were recorded for 5 min postair injection. It was found that total counts of GME were significantly reduced with the purge line open when compared to keeping the purge line closed (P purge line closed compared to keeping the purge line open at flow rates of 750 mL/min and 1000 mL/min (P purge line open and closed, which is due to the small arteriovenous (A-V) shunt(P < 0.001). These results suggest that the integrated arterial filter of the Capiox FX05 oxygenator significantly improves the capturing of GME but has little impact on

  9. Ongoing Technology and Developing Trend of Ar-blowing Purging Plug

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    An introduction of the ongoing technology of ar-gon-blowing purging plugs in China was presented in this work.Gel powders were used as starting materials to enhance the high temperature mechanical properties of the purging plugs.Composite purging plug adopting ex-trusion formed gas-purging bar and slit had its surface structural design improved,which enhanced the resist-ances to thermal shock and molten steel penetration,prolonging the service life.In addition,the safety Was greatly improved by upgrading the framework and pro-duction process,enhancing the resistance to breakout.It is indicated that the developing trend is to produce pur-ging plugs of longer service life and better gas purging rate with different starting materials and structure de-signs to meet the requirements of various metallurgical processes.

  10. Facets of negative affect prior to and following binge-only, purge-only, and binge/purge events in women with bulimia nervosa.

    Science.gov (United States)

    Berg, Kelly C; Crosby, Ross D; Cao, Li; Peterson, Carol B; Engel, Scott G; Mitchell, James E; Wonderlich, Stephen A

    2013-02-01

    Ecological momentary assessment (EMA) data suggest that global negative affect (NA) increases prior to and decreases following episodes of binge eating and purging, providing support for the affect regulation model of BN. The current study examined whether facets of NA are differentially related to bulimic behaviors. Women with bulimia nervosa (BN; n = 133) completed a 2-week EMA protocol. Momentary assessments of 4 facets of NA (Fear, Guilt, Hostility, and Sadness) were derived from the PANAS subscales. Trajectories of the NA facets were modeled prior to and following binge-only, purge-only, and binge/purge events. Fear, Guilt, Hostility, and Sadness increased prior to and decreased following binge-only and binge/purge events. The same results were found for purge-only events, with the exception that Hostility did not increase significantly prior to purging. Notably, ratings of Guilt were higher than those of Fear, Hostility, and Sadness at the time of binge-only and binge/purge events. Furthermore, post hoc analyses demonstrate that Guilt increased prior to and decreased following the 3 behavior types, even after controlling for Fear, Hostility, and Sadness. These results provide further support for the affect regulation model of BN and also suggest that guilt may be particularly important to the pathology of BN.

  11. Determination of blood leukocyte concentration with constant volume acquisition on a flow cytometer is comparable to individualized single platform testing with beads as internal reference standard

    DEFF Research Database (Denmark)

    Hansen, Susan; Dahl, Ronald; Hoffmann, Hans Jürgen

    2008-01-01

    Flow cytometers have a constant flow rate. This enables flow cytometers to measure leukocyte concentrations in a determined volume by acquiring data at a fixed rate over a fixed time and is called constant volume acquisition (CVA). The volume aspirated by a FACS Calibur flow cytometer in 4 min...... at a high rate has a median of 163 microl (IQR 156-170) with TruCount tubes. Leukocyte concentrations of 26 healthy volunteers were measured twice on up to four occasions with a Bürker-Türk chamber, by single platform technology (SPT) with TruCount tubes and on the same data set using CVA. Total leukocyte...... concentrations determined by CVA correlated better with measurements in a Bürker-Türk (BT) chamber than with SPT. Concentrations determined with CVA were 1.86% higher than with BT whereas SPT data were 5.35% higher than BT (pCVA (p

  12. Experimental study on the optimal purge duration of a proton exchange membrane fuel cell with a dead-ended anode

    Science.gov (United States)

    Lin, Yu-Fen; Chen, Yong-Song

    2017-02-01

    When a proton exchange membrane fuel cell (PEMFC) is operated with a dead-ended anode, impurities gradually accumulate within the anode, resulting in a performance drop. An anode purge is thereby ultimately required to remove impurities within the anode. A purge strategy comprises purge interval (valve closed) and purge duration (valve is open). A short purge interval causes frequent and unnecessary activation of the valve, whereas a long purge interval leads to excessive impurity accumulation. A short purge duration causes an incomplete performance recovery, whereas a long purge duration results in low hydrogen utilization. In this study, a series of experimental trials was conducted to simultaneously measure the hydrogen supply rate and power generation of a PEMFC at a frequency of 50 Hz for various operating current density levels and purge durations. The effect of purge duration on the cell's energy efficiency was subsequently analyzed and discussed. The results showed that the optimal purge duration for the PEMFC was approximately 0.2 s. Based on the results of this study, a methodical process for determining optimal purge durations was ultimately proposed for widespread application. Purging approximately one-fourth of anode gas can obtain optimal energy efficiency for a PEMFC with a dead-ended anode.

  13. Behavioral, emotional, and situational context of purging episodes in anorexia nervosa

    Science.gov (United States)

    Goldschmidt, Andrea B.; Accurso, Erin C.; Schreiber-Gregory, Deanna N.; Crosby, Ross D.; Cao, Li; Engel, Scott G.; Mitchell, James E.; Crow, Scott J.; Peterson, Carol B.; Le Grange, Daniel; Wonderlich, Stephen A.

    2015-01-01

    Objective The current study examined behavioral, emotional, and situational factors involved in purging among women with anorexia nervosa (AN). Methods Women with AN (n=118) completed a two-week ecological momentary assessment protocol involving daily reports of eating disorder behaviors, mood, and stressful events. Generalized estimating equations examined the likelihood and context of purging following eating episodes involving both overeating and loss of control (binge eating; BE); loss of control only (LOC); overeating only (OE); and neither loss of control nor overeating (non-pathological eating; NE). Results Relative to NE, purging was more likely to occur following BE, LOC, and OE (Wald chi-square=18.05; p<.001). BE was more strongly associated with subsequent purging than LOC but not OE; the latter two did not differ from one another. Negative affect predicted purging following NE (Wald chi-square=7.71; p=.005). Conclusion Binge eating involving large amounts of food was the strongest predictor of purging in AN, which challenges the notion that loss of control is the most salient aspect of experiencing distress in bulimia nervosa and binge eating disorder. Parallel to findings from the binge eating literature, negative affect strongly predicted purging following non-pathological eating. Further research should clarify the function and triggers of purging in AN. PMID:25643935

  14. From Promise to Purge: The First Years of St. Petersburg University.

    Science.gov (United States)

    Whittaker, Cynthia H.

    1978-01-01

    Discusses the development of St. Petersburg University, Russia, from its inception in 1819 when it was composed of dedicated, eager scholars to the purges in 1821. Concludes that Tsar Alexander I was instrumental in these purges because of his fear that the ideals of European enlightenment in education and politics fostered by the university would…

  15. Chinese Standards on Refractories Purging Plugs and Well Blocks for Refining Ladle

    Institute of Scientific and Technical Information of China (English)

    Zhang Xiaohui

    2009-01-01

    @@ 1 Scope This standard specifies the classification,technical requirements,test methods,inspection rules,marking,packing,transportation,storage and quality certificate of purging plugs and well blocks for refining ladle. This standard is applicable to the directional slit purging plugs and well blocks for refining ladle.

  16. Development of texture-based flow visualization platform%基于纹理的流场动态可视化平台开发

    Institute of Scientific and Technical Information of China (English)

    张尚弘; 易雨君; 江岩; 冶运涛

    2011-01-01

    基于纹理的流场可视化是流场显示的最新方法,该方法采用网格图像变形的方式表现流场,不需要进行流场空间插值计算,可以减小计算量,同时保持很高的显示精度。讨论了基于图像纹理的流场动态显示原理,基于Visual C++和OpenGL开发了流场动态可视化平台,实现了流场数据坐标转换、网格变形与背景图像映射绘制、噪声图像生成与融合、标量场颜色绘制等关键技术。在开发平台上模拟了三峡与葛洲坝两坝间河道流场,并与粒子系统模拟的流场效果进行了比较,结果表明基于纹理的流场动态可视化方法计算量小,能够展示出流场的更多细节。所开发平台的数据适应性好,为流场动态可视化提供了实用的平台工具。%Texture-based flow visualization is a new visualization method of flow field that is based on blending of a warped version of the previous image with a number of background images,a method of high performance using standard features of graphics hardware and no special interpolation.This paper discusses the principles of this new method and develops a visualization platform using Visual C+ +and OpenGL.In the method,several key techniques are adopted,flow field data coordinate conversion,flow field grid modification and drawing background image mapping,generation and integration of noise image,color rendering scalar field,etc.On the platform developed,the river reach between Three Gorges dam and Gezhouba dam is visualized.The platform has advantages of less calculation,more detailed flow field and higher adaptability to data format in comparison to a particles-based system.The platform is useful for dynamic visualization of flow field.

  17. Purge Monitoring Technology for Gaseous Helium (GHe) Conservation

    Science.gov (United States)

    Dickey, Jonathan; Lansaw, John

    2010-01-01

    John C. Stennis Space Center provides rocket engine propulsion testing for the NASA space programs. Since the development of the Space Shuttle, every Space Shuttle Main Engine (SSME) has gone through acceptance testing before going to Kennedy Space Center for integration into the Space Shuttle. The SSME is a large cryogenic rocket engine that used Liquid Oxygen (LO2) and Liquid Hydrogen (LH2) as propellants. Due to the extremely cold cryogenic conditions of this environment, an inert gas, helium, is used as a purge for the engine and propellant lines since it can be used without freezing in the cryogenic environment. As NASA moves forward with the development of the new ARES V launch system, the main engines as well as the upper stage engine will use cryogenic propellants and will require gaseous helium during the development testing of each of these engines. The main engine for the ARES V will be similar in size to the SSME.

  18. Numerical Simulation of Saline Intrusion and Purging in Long Sea Outfalls with Three-Dimensional Model

    Institute of Scientific and Technical Information of China (English)

    WU Wei; YAN Zhong-min; WU Long-hua

    2006-01-01

    Saline intrusion into marine sewage outfalls will greatly decrease the efficiency of sewage disposal. In order to investigate the mechanisms of this flow, in this paper, a three-dimensional numerical model based on FVM (Finite Volume Method) is established. The RNG k-ε model is selected for turbulence modeling. The time-averaged volume fraction equations are introduced to simulate the stratification and interfacial exchange of sewage and seawater in outfalls. Validity of the established three-dimensional numerical model is evaluated by comparisons of numerical results with experimental data. With this three-dimensional numerical model, the internal flow characteristics in outfalls for different sewage discharges are simulated. The results indicate that for a low sewage discharge, saline circulates in the outfall due to intrusion and both the inflowing momentum and the interfacial turbulent mixing are important mechanisms to extrude the saline. For a high sewage discharge, saline intrusion could be avoided. The inflow momentum is the main mechanism to extrude the saline and the interfacial turbulent mixing is not important relatively. Even at a high sewage discharge, the saline wedge would be retained in the main outfall pipe after the risers are purged. It takes a long time for this saline wedge to be extruded by interfacial turbulent mixing.

  19. A CFD Analysis of Hydrogen Leakage During On-Pad Purge in the ORION/ARES I Shared Volume

    Science.gov (United States)

    Ajmani, Kumud; Edwards, Daryl A.

    2011-01-01

    A common open volume is created by the stacking of the Orion vehicle onto the Ares I Upper Stage. Called the Shared Volume, both vehicles contribute to its gas, fluid, and thermal environment. One of these environments is related to hazardous hydrogen gas. While both vehicles use inert purge gas to mitigate any hazardous gas buildup, there are concerns that hydrogen gas may still accumulate and that the Ares I Hazardous Gas Detection System will not be sufficient for monitoring the integrated volume. This Computational Fluid Dynamics (CFD) analysis has been performed to examine these topics. Results of the analysis conclude that the Ares I Hazardous Gas Detection System will be able to sample the vent effluent containing the highest hydrogen concentrations. A second conclusion is that hydrogen does not accumulate under the Orion Service Module (SM) avionics ring as diffusion and purge flow mixing sufficiently dilute the hydrogen to safe concentrations. Finally the hydrogen concentrations within the Orion SM engine nozzle may slightly exceed the 1 percent volume fraction when the entire worse case maximum full leak is directed vertically into the engine nozzle.

  20. Purge gas protected transportable pressurized fuel cell modules and their operation in a power plant

    Science.gov (United States)

    Zafred, Paolo R.; Dederer, Jeffrey T.; Gillett, James E.; Basel, Richard A.; Antenucci, Annette B.

    1996-01-01

    A fuel cell generator apparatus and method of its operation involves: passing pressurized oxidant gas, (O) and pressurized fuel gas, (F), into fuel cell modules, (10 and 12), containing fuel cells, where the modules are each enclosed by a module housing (18), surrounded by an axially elongated pressure vessel (64), where there is a purge gas volume, (62), between the module housing and pressure vessel; passing pressurized purge gas, (P), through the purge gas volume, (62), to dilute any unreacted fuel gas from the modules; and passing exhaust gas, (82), and circulated purge gas and any unreacted fuel gas out of the pressure vessel; where the fuel cell generator apparatus is transpatable when the pressure vessel (64) is horizontally disposed, providing a low center of gravity.

  1. Purge and trap method to determine alpha factors of VOC liquid-phase mass transfer coefficients

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    A theoretical approach and laboratory practice of determining the alpha factors of volatile organic compound (VOC) liquid-phase mass transfer coefficients are present in this study.Using Purge Trap Concentrator, VOC spiked water samples are purged by high-purity nitrogen in the laboratory, the VOC liquid-phase mass transfer rate constants under the laboratory conditions are then obtained by observing the variation of VOCs purged out of the water with the purge time.The alpha factors of VOC liquid-phase mass transfer coefficients are calculated as the ratios of the liquid-phase mass transfer rate constants in real water samples to their counterparts in pure water under the same experimental conditions. This direct and fast approach is easy to control in the laboratory, and would benefit mutual comparison among researchers, so might be useful for thestudy of VOC mass transfer across the liquid-gas interface.

  2. Validated Test Method 5030C: Purge-and-Trap for Aqueous Samples

    Science.gov (United States)

    This method describes a purge-and-trap procedure for the analysis of volatile organic compoundsin aqueous samples & water miscible liquid samples. It also describes the analysis of high concentration soil and waste sample extracts prepared in Method 5035.

  3. Effect of nitrogen crossover on purging strategy in PEM fuel cell systems

    DEFF Research Database (Denmark)

    Rabbani, Raja Abid; Rokni, Masoud

    2013-01-01

    conditions, making it important to investigate the dynamic performance of the system during transitory conditions. The model developed here is able to predict nitrogen crossover in excellent agreement with the design validation data of the stack. The results show that with pure recirculation, voltage...... levels from rising when compared to a fixed purge interval strategy. This model can be used as a base for control and development of anode purge strategies for automotive fuel cell systems....

  4. Better Fitness in Captive Cuvier’s Gazelle despite Inbreeding Increase: Evidence of Purging?

    OpenAIRE

    Eulalia Moreno; Javier Pérez-González; Juan Carranza; Jordi Moya-Laraño

    2015-01-01

    Captive breeding of endangered species often aims at preserving genetic diversity and to avoid the harmful effects of inbreeding. However, deleterious alleles causing inbreeding depression can be purged when inbreeding persists over several generations. Despite its great importance both for evolutionary biology and for captive breeding programmes, few studies have addressed whether and to which extent purging may occur. Here we undertake a longitudinal study with the largest captive populatio...

  5. Effect of the extent of well purging on laboratory parameters of groundwater samples

    Science.gov (United States)

    Reka Mathe, Agnes; Kohler, Artur; Kovacs, Jozsef

    2017-04-01

    Chemicals reaching groundwater cause water quality deterioration. Reconnaissance and remediation demands high financial and human resources. Groundwater samples are important sources of information. Representativity of these samples is fundamental to decision making. According to relevant literature the way of sampling and the sampling equipment can affect laboratory concentrations measured in samples. Detailed and systematic research on this field is missing from even international literature. Groundwater sampling procedures are regulated worldwide. Regulations describe how to sample a groundwater monitoring well. The most common element in these regulations is well purging prior to sampling. The aim of purging the well is to avoid taking the sample from the stagnant water instead of from formation water. The stagnant water forms inside and around the well because the well casing provides direct contact with the atmosphere, changing the physico-chemical composition of the well water. Sample from the stagnant water is not representative of the formation water. Regulations regarding the extent of the purging are different. Purging is mostly defined as multiply (3-5) well volumes, and/or reaching stabilization of some purged water parameters (pH, specific conductivity, etc.). There are hints for sampling without purging. To define the necessary extent of the purging repeated pumping is conducted, triplicate samples are taken at the beginning of purging, at one, two and three times well volumes and at parameter stabilization. Triplicate samples are the means to account for laboratory errors. The subsurface is not static, the test is repeated 10 times. Up to now three tests were completed.

  6. Regimes of Decomposition of Clathrate in Natural Strata Purged by Methane

    Science.gov (United States)

    Khasanov, M.; Shagapov, V.

    2016-06-01

    The process of decomposition of a methane clathrate in a finite-length stratum initially saturated with methane clathrate and methane, which is purged by warm methane, is studied. The influence of the initial parameters of the stratum and purging conditions on the evolution of methane clathrate temperature and saturation is examined. The existence of solutions is demonstrated, which predict methane clathrate decomposition both on the frontal surface and in the volume zone.

  7. Microstructure and physical properties of steel-ladle purging plug refractory materials

    Science.gov (United States)

    Long, Bin; Xu, Gui-ying; Andreas, Buhr

    2017-02-01

    Three different castables were prepared as steel-ladle purging-plug refractory materials: corundum-based low-cement castable (C-LCC), corundum-spinel-based low-cement castable (C-S-LCC), and no-cement corundum-spinel castable (C-S-NCC) (hydratable alumina ρ-Al2O3 bonded). The properties of these castables were characterized with regard to water demand/flow ability, cold crushing strength (CCS), cold modulus of rupture (CMoR), permanent linear change (PLC), apparent porosity, and hot modulus of rupture (HMoR). The results show the CCS/CMoR and HMoR of C-LCC and C-S-LCC are greater than those of the castable C-S-NCC. According to the microstructure analysis, the sintering effect and the bonding type of the matrix material differ among the three castables. The calcium hexaluminate (CA6) phase in the matrix of C-LCC enhances the cold and hot mechanical strengths. In the case of C-S-LCC, the CA6 and 2CaO·2MgO·14Al2O3 (C2M2A14) ternary phases generated from the matrix can greatly increase the cold and hot mechanical strengths. In the case of the no-cement castable, sintering becomes difficult, resulting in a lower mechanical strength.

  8. Automatic heating and cooling system in a gas purge microsyringe extraction.

    Science.gov (United States)

    Piao, Xiangfan; Bi, Jinhu; Yang, Cui; Wang, Xiaoping; Wang, Juan; Li, Donghao

    2011-10-30

    The gas purge microsyringe extraction (GP-MSE) technique offers quantitative and simultaneous extraction, and rapid gas chromatographic-mass spectrometric determination of volatile and semivolatile chemicals is possible. To simplify the application, a new automatic temperature control system was developed here. Stable heating and cooling over a wide range of temperatures were achieved using a micro-heater and thermoelectric cooler under varying gas flow conditions. Temperatures could be accurately controlled in the range 20-350°C (heating) and 20 to -4°C (cooling). Temperature effects on the extraction performance of the GP-MSE were experimentally investigated by comparing the recoveries of polycyclic aromatic hydrocarbons (PAHs) under various experimental conditions. A sample treatment was completed within 3 min, which is much less than the time required for chromatographic analysis. The recovery of chemicals determined ranged from 81 to 96%. High reproducibility data (RSD ≤ 5%) were obtained for direct extraction of various analytes in spiked complex plant and biological samples. The data show that the heating and cooling system has potential applications in GP-MSE system for the direct determination of various kinds of volatile and semivolatile chemicals from complex matrices without any, or only minor, sample pretreatment.

  9. 吹扫捕集-气质联用测定水中苯系物%Purge and trap- determination of BTEXs in water by GC/MS

    Institute of Scientific and Technical Information of China (English)

    韩增玉; 黄彬

    2012-01-01

    The BTEXs were enriched by the system of purge - trap, then determined by GC/MS. The effects that include the conditions of GC, the time of purge, flow rate of purge and the time of desorption , the temp of de- sorption were discussed. The average recoveries were 96 - 102%. The limits of detection were 0.03 -0.39μg/L. The method can be applied to analysis of BTEXs in water.%以吹扫捕集方式,通过GC/MS测定水中苯系物。考察了吹扫时间、吹扫流量、解析时间、解析温度对回收率的影响,确定了测定水中苯系物最佳实验条件。方法平均回收率96%~102%,检出限为0.03~0.39μg/L,本方法可用于水中痕量苯系物测定。

  10. Purge-assisted headspace solid-phase microextraction combined with gas chromatography-mass spectrometry for determination of chlorophenols in aqueous samples.

    Science.gov (United States)

    Ho, Hsin-Pin; Lee, Ren-Jye; Lee, Maw-Rong

    2008-12-12

    A simple, economical and very effective method is demonstrated for simultaneous determination of 2,4-dichlorophenol, 2,4,6-trichlorophenol, 2,3,4,6-tetrachlorophenol and pentachlorophenol, in aqueous samples, by using purge-assisted headspace solid-phase microextraction (PA/HS-SPME) coupled to gas chromatography-mass spectrometry (GC-MS). In the new method, purging the sample enhances the removal of the trace chlorophenols without derivatization from the matrices to the headspace. Extraction parameters including extraction temperature, purge gas flow rate and extraction time were systematically investigated. Under optimal conditions, the relative standard deviations (RSDs) were 4-11% at 50 pg/mL and 5-14% at 5 pg/mL, respectively. The recoveries were in the range of 83-114%. Detection limits were determined at the fg level. These results indicate that PA/HS-SPME provides a significant contribution to highly efficient extraction of semi-volatile CPs, especially for pentachlorophenol, which has the smallest Henry's constant and large octanol-water partitioning coefficient. In addition, the proposed method was successfully applied to the analysis of chlorophenols in landfill leachate. New perspectives are opened for headspace extraction of relatively low vapor pressure compounds in complex matrices.

  11. [Purging behaviors and nutritional status in anorexia nervosa and bulimia nervosa].

    Science.gov (United States)

    Vaz, F J; García-Herráiz, A; López-Vinuesa, B; Monge, M; Fernández-Gil, M A; Guisado, J A

    2003-01-01

    The aim of the study was to investigate whether the use of purgative methods in patients with eating disorders (anorexia nervosa [AN] and bulimia nervosa [BN]) could be capable of producing changes in the nutritional status of the patients. The group under study was composed of 184 female eating disordered outpatients. One hundred and sixteen patients (63.0%) fulfilled the DSM-IV diagnostic criteria for BN (90 purging type, 26 nonpurging type). Sixty eight patients (37.0%) fulfilled the DSM-IV criteria for the diagnosis of AN (48 restricting type, 20 binging-purging type). The assessment process included anthropometry (body circumferences and skinfold thickness) and body impedance analysis. The two subgroups of AN patients significantly differed from each of the BN subgroups. From a nutritional point of view, some significant differences between the two DSM-IV subtypes of AN existed, but not between the purging type and the nonpurging type of BN. The paper discusses the clinical significance of these findings. An alternative subtypification of AN patients is proposed: 1) restricting type [patients who control their food intake and do not purge]; 2) purging type [patient with true episodes of binging which are followed by purgative behaviors]; and 3) pseudopurging type [patients with subjective binging episodes who use purging methods].

  12. Distinguishing Between Risk Factors for Bulimia Nervosa, Binge Eating Disorder, and Purging Disorder.

    Science.gov (United States)

    Allen, Karina L; Byrne, Susan M; Crosby, Ross D

    2015-08-01

    Binge eating disorder and purging disorder have gained recognition as distinct eating disorder diagnoses, but risk factors for these conditions have not yet been established. This study aimed to evaluate a prospective, mediational model of risk for the full range of binge eating and purging eating disorders, with attention to possible diagnostic differences. Specific aims were to determine, first, whether eating, weight and shape concerns at age 14 would mediate the relationship between parent-perceived childhood overweight at age 10 and a binge eating or purging eating disorder between age 15 and 20, and, second, whether this mediational model would differ across bulimia nervosa, binge eating disorder, and purging disorder. Participants (N = 1,160; 51 % female) were drawn from the Western Australian Pregnancy Cohort (Raine) Study, which has followed children from pre-birth to age 20. Eating disorders were assessed via self-report questionnaires when participants were aged 14, 17 and 20. There were 146 participants (82 % female) with a binge eating or purging eating disorder with onset between age 15 and 20 [bulimia nervosa = 81 (86 % female), binge eating disorder = 43 (74 % female), purging disorder = 22 (77 % female)]. Simple mediation analysis with bootstrapping was used to test the hypothesized model of risk, with early adolescent eating, weight and shape concerns positioned as a mediator between parent-perceived childhood overweight and later onset of a binge eating or purging eating disorder. Subsequently, a conditional process model (a moderated mediation model) was specified to determine if model pathways differed significantly by eating disorder diagnosis. In the simple mediation model, there was a significant indirect effect of parent-perceived childhood overweight on risk for a binge eating or purging eating disorder in late adolescence, mediated by eating, weight and shape concerns in early adolescence. In the conditional process model

  13. Adaptation of ubiquitin-PNA based sperm quality assay for semen evaluation by a conventional flow cytometer and a dedicated platform for flow cytometric semen analysis.

    Science.gov (United States)

    Odhiambo, J F; Sutovsky, M; DeJarnette, J M; Marshall, C; Sutovsky, P

    2011-10-01

    The purpose of semen quality evaluation is to predict the fertility potential of the sample in an objective, rapid and inexpensive manner. However, utilization of sperm quality biomarkers such as ubiquitin and lectin Arachis hypogaea agglutinin (PNA) for flow cytometric semen evaluation might eliminate the need for visual assessment by microscopy. Herein, we demonstrate a robust ubiquitin and PNA-based semen evaluation conducted on a simple, easy to operate, dedicated sperm flow cytometer, EasyCyte Plus (IMV Technologies, L'Aigle, France). Semen samples were collected periodically from two dairy bulls, which were subjected to temporary scrotal insults to induce variable semen quality. Samples were labeled with fluorescently-conjugated anti-ubiquitin antibodies (bind exclusively to the surface of defective sperm) and lectin PNA (binds to acrosomal surface in prematurely capacitated and acrosome-damaged sperm). Fluorescent properties of the samples were measured with a conventional flow cytometer (Becton Dickinson FACScan; Becton Dickinson Corp., Franklin Lakes, NJ, USA) and by the EasyCyte (IMV Technologies) instrument. Data from the two flow cytometers were positively correlated for the percentage of PNA-positive sperm with a damaged acrosome (r = 0.47; P flow cytometric semen evaluation.

  14. Energy saving for OpenFlow switch on the NetFPGA platform based on queue engineering.

    Science.gov (United States)

    Vu, Tran Hoang; Luc, Vu Cong; Quan, Nguyen Trung; Thanh, Nguyen Huu; Nam, Pham Ngoc

    2015-01-01

    Data centers play an important role in our daily activities. The increasing demand on data centers in both scale and size has led to huge energy consumption that rises the cost of data centers. Besides, environmental impacts also increase considerably due to a large amount of carbon emissions. In this paper, we present a design aimed at green networking by reducing the power consumption for routers and switches. Firstly, we design the Balance Switch on the NetFPGA platform to save consumed energy based on Queue Engineering. Secondly, we design the test-bed system to precisely measure the consumed energy of our switches. Experimental results show that energy saving of our switches is about 30% - 35% of power consumption according to variation of input traffic compared with normal Openflow Switch. Finally, we describe performance evaluations.

  15. A novel surgical strategy for secondary hyperparathyroidism: Purge parathyroidectomy.

    Science.gov (United States)

    Shan, Cheng-Xiang; Qiu, Nian-Cun; Zha, Si-Luo; Liu, Miao-E; Wang, Qiang; Zhu, Pei-Pei; Du, Zhi-Peng; Xia, Chun-Yan; Qiu, Ming; Zhang, Wei

    2017-07-01

    This study was intended to demonstrate the feasibility and efficacy of purge parathyroidectomy (PPTX) for patients with secondary hyperparathyroidism (SHPT). The "seed, environment, and soil" medical hypothesis was first raised, following review of the literatures, to demonstrate the possible causes of persistence or recurrence of SHPT after parathyroidectomy. Subsequently, the novel surgical strategy of PPTX was proposed, which involves comprehensive resection of the fibro-fatty tissues, including visible or invisible parathyroid, within the region surrounded by the thyroid cartilage, bilateral carotid artery sheath, and the brachiocephalic artery. The perioperative information and clinical outcomes of patients who underwent PPTX from June 2016 to December 2016 were analyzed. In total, PPTX was performed safely in nine patients with SHPT from June 2016 to December 2016. The operative time for PPTX ranged from 95 to 135 min, and blood loss ranged from 20 to 40 mL. No patients with perioperative death, bleeding, convulsions, or recurrent laryngeal nerve injury were reported. The preoperative concentration of PTH ranged from 1062 to 2879 pg/mL, and from 12.35 to 72.69 pg/mL on the first day after surgery. In total, 37 parathyroid glands were resected. The postoperative pathologic examination showed that supernumerary or ectopic parathyroid tissues were found within the "non-parathyroid" tissues in three patients. No cases encountered persistence or recurrence of SHPT, or severe hypocalcemia during the follow-up period. PPTX involves comprehensive resection of supernumerary and ectopic parathyroid tissues, which may provide a more permanent means of reducing PTH levels. Copyright © 2017. Published by Elsevier Ltd.

  16. Holographic microscopy and microfluidics platform for measuring wall stress and 3D flow over surfaces textured by micro-pillars

    Science.gov (United States)

    Bocanegra Evans, Humberto; Gorumlu, Serdar; Aksak, Burak; Castillo, Luciano; Sheng, Jian

    2016-06-01

    Understanding how fluid flow interacts with micro-textured surfaces is crucial for a broad range of key biological processes and engineering applications including particle dispersion, pathogenic infections, and drag manipulation by surface topology. We use high-speed digital holographic microscopy (DHM) in combination with a correlation based de-noising algorithm to overcome the optical interference generated by surface roughness and to capture a large number of 3D particle trajectories in a microfluidic channel with one surface patterned with micropillars. It allows us to obtain a 3D ensembled velocity field with an uncertainty of 0.06% and 2D wall shear stress distribution at the resolution of ~65 μPa. Contrary to laminar flow in most microfluidics, we find that the flow is three-dimensional and complex for the textured microchannel. While the micropillars affect the velocity flow field locally, their presence is felt globally in terms of wall shear stresses at the channel walls. These findings imply that micro-scale mixing and wall stress sensing/manipulation can be achieved through hydro-dynamically smooth but topologically rough micropillars.

  17. Evaluation of Variable Refrigerant Flow Systems Performance on Oak Ridge National Laboratory s Flexible Research Platform: Part 1 Cooling Season Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Im, Piljae [ORNL; Malhotra, Mini [ORNL; Munk, Jeffrey D [ORNL

    2016-08-01

    This report provides second-year cooling season test results for the multi-year project titled “Evaluation of Variable Refrigeration Flow (VRF) System on Oak Ridge National Laboratory (ORNL)’s Flexible Research Platform (FRP).” The purpose of the second-year project was to (1) evaluate the full- and partload performance of VRF systems compared with an existing baseline heating, ventilation, and airconditioning (HVAC) system, which is a conventional rooftop unit (RTU) variable-air-volume (VAV) system with electric resistance heating and (2) use hourly building energy simulation to evaluate the energy savings potential of using VRF systems in major US cities. The second-year project performance period was from July 2015 through June 2016.

  18. Absorption-Modulated Crossed-Optical Fiber-Sensor Platform for Measurements in Liquid Environments and Flow Streams

    Directory of Open Access Journals (Sweden)

    Paul E. Henning

    2017-01-01

    Full Text Available A new evanescent-wave fiber sensor is described that utilizes absorption-modulated luminescence (AML in combination with a crossed-fiber sensor platform. The luminescence signals of two crossed-fiber reference regions, placed on opposite sides of the stretch of fiber supporting the absorbance sensor, monitor the optical intensity in the fiber core. Evanescent absorption of the sensor reduces a portion of the excitation light and modulates the luminescence of the second reference region. The attenuation is determined from the luminescence intensity of both reference regions similar to the Beer-Lambert Law. The AML-Crossed-Fiber technique was demonstrated using the absorbance of the Zn(II-PAN2 complex at 555 nm. A linear response was obtained over a zinc(II concentration range of 0 to 20 μM (approximately 0 to 1.3 ppm. A nonlinear response was observed at higher zinc(II concentrations and was attributed to depletion of higher-order modes in the fiber. This was corroborated by the measured induced repopulation of these modes.

  19. The Initial Purging Policies after the 1965 Incident at Lubang Buaya

    Directory of Open Access Journals (Sweden)

    Yosef Djakababa

    2013-01-01

    Full Text Available After the Lubang Buaya incident on 1 October 1965 in which six top Indonesian Army generals and a lieutenant were killed, the Army began to implement a nationwide purging campaign with the assistance of civilian anti-communist groups. Thousands of PKI members, supporters and pro-Sukarno groups/individuals immediately became the target of this purge. For organisational purposes, several purging policies were released and then strictly enforced. The official purging policies that are highlighted in this paper are a series of initial directives that were released within days of the generals’ executions. They do not explicitly translate into orders to kill, but are more of a guideline to help anti-communist officials classify and contain communists and other PKI followers. This article attempts to show how these initial directives evolved and also discusses competing purge policies from non-military sources. The co-existence and overlapping nature of the various directives indicate that a power struggle existed between the anti-communist group led by General Soeharto and the presidium of the Dwikora Cabinet who were loyal to President Soekarno.

  20. Appetite regulatory hormones in women with anorexia nervosa: binge-eating/purging versus restricting type.

    Science.gov (United States)

    Eddy, Kamryn T; Lawson, Elizabeth A; Meade, Christina; Meenaghan, Erinne; Horton, Sarah E; Misra, Madhusmita; Klibanski, Anne; Miller, Karen K

    2015-01-01

    Anorexia nervosa is a psychiatric illness characterized by low weight, disordered eating, and hallmark neuroendocrine dysfunction. Behavioral phenotypes are defined by predominant restriction or bingeing/purging; binge-eating/purging type anorexia nervosa is associated with poorer outcome. The pathophysiology underlying anorexia nervosa types is unknown, but altered hormones, known to be involved in eating behaviors, may play a role. To examine the role of anorexigenic hormones in anorexia nervosa subtypes, we examined serum levels of peptide YY (PYY; total and active [3-36] forms), brain-derived neurotrophic factor (BDNF), and leptin as primary outcomes in women with DSM-5 restricting type anorexia nervosa (n = 50), binge-eating/purging type anorexia nervosa (n = 25), and healthy controls (n = 22). In addition, women completed validated secondary outcome measures of eating disorder psychopathology (Eating Disorder Examination-Questionnaire) and depression and anxiety symptoms (Hamilton Rating Scales for Depression [HDRS] and Anxiety [HARS]). The study samples were collected from May 22, 2004, to February 7, 2012. Mean PYY 3-36 and leptin levels were lower and BDNF levels higher in binge-eating/purging type anorexia nervosa than in restricting type anorexia nervosa (all P values anorexia nervosa types were significant (P anorexia nervosa, the anorexigenic hormones PYY, BDNF, and leptin are differentially regulated between the restricting and binge/purge types. Whether these hormone pathways play etiologic roles with regard to anorexia nervosa behavioral types or are compensatory merits further study. © Copyright 2015 Physicians Postgraduate Press, Inc.

  1. Platform Constellations

    DEFF Research Database (Denmark)

    Staykova, Kalina Stefanova; Damsgaard, Jan

    2016-01-01

    This research paper presents an initial attempt to introduce and explain the emergence of new phenomenon, which we refer to as platform constellations. Functioning as highly modular systems, the platform constellations are collections of highly connected platforms which co-exist in parallel...... and as such allow us to study platforms not only as separate entities, but also to investigate the relationship between several platforms offered and governed by one and the same platform provider. By investigating two case studies of indigenous platform constellations formed around the hugely popular instant...... messaging apps KakaoTalk and LINE, we are able to gain valuable insights about the nature of these new constructions and to capture and synthesize their main characteristics in a framework. Our results show that platform constellations possess unique innovative capabilities, which can improve users...

  2. Capillary flow layer-by-layer: a microfluidic platform for the high-throughput assembly and screening of nanolayered film libraries.

    Science.gov (United States)

    Castleberry, Steven A; Li, Wei; Deng, Di; Mayner, Sarah; Hammond, Paula T

    2014-07-22

    Layer-by-layer (LbL) assembly is a powerful tool with increasing real world applications in energy, biomaterials, active surfaces, and membranes; however, the current state of the art requires individual sample construction using large quantities of material. Here we describe a technique using capillary flow within a microfluidic device to drive high-throughput assembly of LbL film libraries. This capillary flow layer-by-layer (CF-LbL) method significantly reduces material waste, improves quality control, and expands the potential applications of LbL into new research spaces. The method can be operated as a simple lab benchtop apparatus or combined with liquid-handling robotics to extend the library size. Here we describe and demonstrate the technique and establish its ability to recreate and expand on the known literature for film growth and morphology. We use the same platform to assay biological properties such as cell adhesion and proliferation and ultimately provide an example of the use of this approach to identify LbL films for surface-based DNA transfection of commonly used cell types.

  3. Local area water removal analysis of a proton exchange membrane fuel cell under gas purge conditions.

    Science.gov (United States)

    Lee, Chi-Yuan; Lee, Yu-Ming; Lee, Shuo-Jen

    2012-01-01

    In this study, local area water content distribution under various gas purging conditions are experimentally analyzed for the first time. The local high frequency resistance (HFR) is measured using novel micro sensors. The results reveal that the liquid water removal rate in a membrane electrode assembly (MEA) is non-uniform. In the under-the-channel area, the removal of liquid water is governed by both convective and diffusive flux of the through-plane drying. Thus, almost all of the liquid water is removed within 30 s of purging with gas. However, liquid water that is stored in the under-the-rib area is not easy to remove during 1 min of gas purging. Therefore, the re-hydration of the membrane by internal diffusive flux is faster than that in the under-the-channel area. Consequently, local fuel starvation and membrane degradation can degrade the performance of a fuel cell that is started from cold.

  4. A synthetic biochemistry molecular purge valve module that maintains redox balance.

    Science.gov (United States)

    Opgenorth, Paul H; Korman, Tyler P; Bowie, James U

    2014-06-17

    The greatest potential environmental benefit of metabolic engineering would be the production of high-volume commodity chemicals, such as biofuels. Yet, the high yields required for the economic viability of low-value chemicals is particularly hard to achieve in microbes owing to the myriad competing biochemical pathways. An alternative approach, which we call synthetic biochemistry, is to eliminate the organism by constructing biochemical pathways in vitro. Viable synthetic biochemistry, however, will require simple methods to replace the cellular circuitry that maintains cofactor balance. Here we design a simple purge valve module for maintaining NADP(+)/NADPH balance. We test the purge valve in the production of polyhydroxybutyryl bioplastic and isoprene--pathways where cofactor generation and utilization are unbalanced. We find that the regulatory system is highly robust to variations in cofactor levels and readily transportable. The molecular purge valve provides a step towards developing continuously operating, sustainable synthetic biochemistry systems.

  5. Purging using the Heimlich maneuver among children and adolescents with eating disorders.

    Science.gov (United States)

    Boachie, Ahmed; Kusi Appiah, Edigna; Jubin, Michelle; Jasper, Karin

    2015-09-01

    This case report describes five independent cases of children and adolescents assessed for eating disorders who disclosed using the Heimlich maneuver as a purging technique. The maneuver is meant to be used only in life or death situations, likely once or less in any person's lifetime. A child or adolescent with an eating disorder may be using it to self-induce vomiting on a daily basis, increasing the risk of complications, including potential damage to major organs of the body. Asking patients who purge to elaborate on the methods with which they purge can provide clinicians with fuller information, improving their ability to select appropriate medical tests and interventions. Thorough investigations of physical complaints during the patient assessment may be warranted, including examining patients for possible rib fractures, hemorrhages, perforations of the hollow viscous, and other forms of blunt abdominal traumas.

  6. Thinness and eating expectancies predict subsequent binge-eating and purging behavior among adolescent girls.

    Science.gov (United States)

    Smith, Gregory T; Simmons, Jean R; Flory, Kate; Annus, Agnes M; Hill, Kelly K

    2007-02-01

    One's expectancies for reinforcement from eating or from thinness are thought to represent summaries of one's eating-related learning history and to thus influence the development of binge-eating and purging behavior. In a 3-year longitudinal study, the authors tested this hypothesis and the hypothesis that binge eating also influences subsequent expectancy development. The authors used trajectory analysis to identify groups of middle school girls who followed different trajectories of binge eating, purging, eating expectancies, and thinness expectancies. Initial eating and thinness reinforcement expectancies identified girls whose binge eating and purging increased during middle school, and expectancies differentiated girls who began these problem behaviors from girls who did not. Initial binge-eating scores differentiated among eating expectancy developmental trajectories. The onset of most behaviors can be understood in terms of learned expectancies for reinforcement from these behaviors. The same model can be applied to the risk for eating disorders.

  7. Hydrogel-coated feed spacers in two-phase flow cleaning in spiral wound membrane elements: a novel platform for eco-friendly biofouling mitigation.

    Science.gov (United States)

    Wibisono, Yusuf; Yandi, Wetra; Golabi, Mohsen; Nugraha, Roni; Cornelissen, Emile R; Kemperman, Antoine J B; Ederth, Thomas; Nijmeijer, Kitty

    2015-03-15

    Biofouling is still a major challenge in the application of nanofiltration and reverse osmosis membranes. Here we present a platform approach for environmentally friendly biofouling control using a combination of a hydrogel-coated feed spacer and two-phase flow cleaning. Neutral (polyHEMA-co-PEG10MA), cationic (polyDMAEMA) and anionic (polySPMA) hydrogels have been successfully grafted onto polypropylene (PP) feed spacers via plasma-mediated UV-polymerization. These coatings maintained their chemical stability after 7 days incubation in neutral (pH 7), acidic (pH 5) and basic (pH 9) environments. Anti-biofouling properties of these coatings were evaluated by Escherichia coli attachment assay and nanofiltration experiments at a TMP of 600 kPag using tap water with additional nutrients as feed and by using optical coherence tomography. Especially the anionic polySPMA-coated PP feed spacer shows reduced attachment of E. coli and biofouling in the spacer-filled narrow channels resulting in delayed biofilm growth. Employing this highly hydrophilic coating during removal of biofouling by two-phase flow cleaning also showed enhanced cleaning efficiency, feed channel pressure drop and flux recoveries. The strong hydrophilic nature and the presence of negative charge on polySPMA are most probably responsible for the improved antifouling behavior. A combination of polySPMA-coated PP feed spacers and two-phase flow cleaning therefore is promising and an environmentally friendly approach to control biofouling in NF/RO systems employing spiral-wound membrane modules.

  8. Multiplex immunoassay for persistent organic pollutants in tilapia: comparison of imaging- and flow cytometry-based platforms using spectrally encoded paramagnetic microspheres.

    Science.gov (United States)

    Meimaridou, Anastasia; Haasnoot, Willem; Shelver, Weilin L; Franek, Milan; Nielen, Michel W F

    2013-01-01

    Recent developments in spectrally encoded microspheres (SEMs)-based technologies provide high multiplexing possibilities. Most SEMs-based assays require a flow cytometer with sophisticated fluidics and optics. A new imaging super-paramagnetic SEMs-based alternative platform transports SEMs with considerably less fluid volume into a measuring chamber. Once there SEMs are held in a monolayer by a magnet. Light-emitting diodes (LEDs) are focused on the chamber to illuminate the SEMs - instead of lasers and they are imaged by a charge-coupled device (CCD) detector, offering a more compact sized, transportable and affordable system. The feasibility of utilising this system to develop a 3-plex SEMs-based imaging immunoassay (IMIA) for the screening of persistent organic pollutants (POPs) was studied. Moreover the performance characteristics of 3-plex IMIA were critically compared with the conventional 3-plex flow cytometric immunoassay (FCIA). Both SEM technologies have potential for the multiplex analysis of polychlorinated biphenyls (PCBs), polybrominated diphenyl ethers (PBDEs) and polycyclic aromatic hydrocarbons (PAHs) in buffer and fish extract with insignificant differences in assay sensitivities. Furthermore, we developed a faster and simpler, modified QuEChERS-like generic POPs extraction from tilapia fillet using sodium hydrogen carbonate as one of the salt additives and dispersive solid-phase extraction (dSPE) as a clean-up. Finally, a preliminary in-house validation using 40 different blank and spiked tilapia fillet samples was performed in both systems and the results obtained were critically compared. The lower-cost imaging SEMs-based system performed similarly to the original flow cytometer and, in combination with the new quicker QuEChERS-like extraction, it has high potential for future rapid screening of POPs in several other sample matrices such as other fish species, vegetable refined oils and environmental samples.

  9. Effect of the purging gas on properties of Ti stabilized AISI 321 stainless steel TIG welds

    Energy Technology Data Exchange (ETDEWEB)

    Taban, Emel; Kaluc, Erdinc; Aykan, T. Serkan [Kocaeli Univ. (Turkey). Dept. of Mechanical Engineering

    2014-07-01

    Gas purging is necessary to provide a high quality of stainless steel pipe welding in order to prevent oxidation of the weld zone inside the pipe. AISI 321 stabilized austenitic stainless steel pipes commonly preferred in refinery applications have been welded by the TIG welding process both with and without the use of purging gas. As purging gases, Ar, N{sub 2}, Ar + N{sub 2} and N{sub 2} + 10% H{sub 2} were used, respectively. The aim of this investigation is to detect the effect of purging gas on the weld joint properties such as microstructure, corrosion, strength and impact toughness. Macro sections and microstructures of the welds were investigated. Chemical composition analysis to obtain the nitrogen, oxygen and hydrogen content of the weld root was done by Leco analysis. Ferrite content of the beads including root and cap passes were measured by a ferritscope. Vickers hardness (HV10) values were obtained. Intergranular and pitting corrosion tests were applied to determine the corrosion resistance of all welds. Type of the purging gas affected pitting corrosion properties as well as the ferrite content and nitrogen, oxygen and hydrogen contents at the roots of the welds. Any hot cracking problems are not predicted as the weld still solidifies with ferrite in the primary phase as confirmed by microstructural and ferrite content analysis. Mechanical testing showed no significant change according to the purge gas. AISI 321 steel and 347 consumable compositions would permit use of nitrogen rich gases for root shielding without a risk of hot cracking.

  10. Understanding and predicting the fitness decline of shrunk populations: inbreeding, purging, mutation, and standard selection.

    Science.gov (United States)

    García-Dorado, Aurora

    2012-04-01

    The joint consequences of inbreeding, natural selection, and deleterious mutation on mean fitness after population shrinkage are of great importance in evolution and can be critical to the conservation of endangered populations. I present simple analytical equations that predict these consequences, improving and extending a previous heuristic treatment. Purge is defined as the "extra" selection induced by inbreeding, due to the "extra" fitness disadvantage (2d) of homozygotes for (partially) recessive deleterious alleles. Its effect is accounted for by using, instead of the classical inbreeding coefficient f, a purged inbreeding coefficient g that is weighed by the reduction of the frequency of deleterious alleles caused by purging. When the effective size of a large population is reduced to a smaller stable value N (with Nd ≥ 1), the purged inbreeding coefficient after t generations can be predicted as g(t) ≈ [(1 - 1/2N) g(t)(-1) + 1/2N](1 - 2d f(t)(-1)), showing how purging acts upon previously accumulated inbreeding and how its efficiency increases with N. This implies an early fitness decay, followed by some recovery. During this process, the inbreeding depression rate shifts from its ancestral value (δ) to that of the mutation-selection-drift balance corresponding to N (δ*), and standard selection cancels out the inbreeding depression ascribed to δ*. Therefore, purge and inbreeding operate only upon the remaining δ - δ*. The method is applied to the conservation strategy in which family contributions to the breeding pool are equal and is extended to make use of genealogical information. All these predictions are checked using computer simulation.

  11. Colonic diverticular bleeding: urgent colonoscopy without purging and endoscopic treatment with epinephrine and hemoclips

    Directory of Open Access Journals (Sweden)

    Ignacio Couto-Worner

    2013-09-01

    Full Text Available Diverticular disease is the most frequent cause of lower gastrointestinal bleeding. Most of the times, bleeding stops without any intervention but in 10-20 % of the cases it is necessary to treat the hemorrhage. Several modalities of endoscopic treatment have been described after purging the colon. We present five cases of severe diverticular bleeding treated with injection of epinephrine and hemoclips. All the colonoscopies were performed without purging of the colon in an emergency setting, with correct visualization of the point of bleeding. Patients recovered well avoiding other aggressive procedures such as angiography or surgery.

  12. Development and validation of purged thermal protection systems for liquid hydrogen fuel tanks of hypersonic vehicles

    Science.gov (United States)

    Helenbrook, R. D.; Colt, J. Z.

    1977-01-01

    An economical, lightweight, safe, efficient, reliable, and reusable insulation system was developed for hypersonic cruise vehicle hydrogen fuel tanks. Results indicate that, a nitrogen purged, layered insulation system with nonpermeable closed-cell insulation next to the cryogenic tank and a high service temperature fibrous insulation surrounding it, is potentially an attractive solution to the insulation problem. For the postulated hypersonic flight the average unit weight of the purged insulation system (including insulation, condensate and fuel boil off) is 6.31 kg/sq m (1.29 psf). Limited cyclic tests of large specimens of closed cell polymethacrylimide foam indicate it will withstand the expected thermal cycle.

  13. Whitey Swagelok SCHe Ball Valves Provide Isolation between SCHe Purge Lines C and D and the Process Vent

    Energy Technology Data Exchange (ETDEWEB)

    MISKA, C.R.

    2000-09-15

    These valves are 1/4 inch ball valves fabricated of 316 stainless steel. Packing is TFE (standard). They provide an isolation function betwen SCHe Purge Line C, (PV-V-*079), and Purge Line D, (PV-V-*080), and the Process Vent.

  14. KPT系列吹扫装置的典型应用%Typical Applications of the KPT Series Purge Device

    Institute of Scientific and Technical Information of China (English)

    陈晶

    2012-01-01

    针对KPT系列吹扫装置原理进行了深入分析,并对吹扫装置的几种应用进行阐述。%More in-depth analysis of device principle for the KPT series purge is carried out and several purge applications are described in detail.

  15. Payment Platform

    DEFF Research Database (Denmark)

    Hjelholt, Morten; Damsgaard, Jan

    2012-01-01

    Payment transactions through the use of physical coins, bank notes or credit cards have for centuries been the standard formats of exchanging money. Recently online and mobile digital payment platforms has entered the stage as contenders to this position and possibly could penetrate societies...... thoroughly and substitute current payment standards in the decades to come. This paper portrays how digital payment platforms evolve in socio-technical niches and how various technological platforms aim for institutional attention in their attempt to challenge earlier platforms and standards. The paper...... applies a co-evolutionary multilevel perspective to model the interplay and processes between technology and society wherein digital payment platforms potentially will substitute other payment platforms just like the credit card negated the check. On this basis this paper formulate a multilevel conceptual...

  16. Evaluation of Variable Refrigerant Flow Systems Performance and the Enhanced Control Algorithm on Oak Ridge National Laboratory s Flexible Research Platform

    Energy Technology Data Exchange (ETDEWEB)

    Im, Piljae [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Munk, Jeffrey D [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Gehl, Anthony C [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2015-06-01

    A research project “Evaluation of Variable Refrigerant Flow (VRF) Systems Performance and the Enhanced Control Algorithm on Oak Ridge National Laboratory’s (ORNL’s) Flexible Research Platform” was performed to (1) install and validate the performance of Samsung VRF systems compared with the baseline rooftop unit (RTU) variable-air-volume (VAV) system and (2) evaluate the enhanced control algorithm for the VRF system on the two-story flexible research platform (FRP) in Oak Ridge, Tennessee. Based on the VRF system designed by Samsung and ORNL, the system was installed from February 18 through April 15, 2014. The final commissioning and system optimization were completed on June 2, 2014, and the initial test for system operation was started the following day, June 3, 2014. In addition, the enhanced control algorithm was implemented and updated on June 18. After a series of additional commissioning actions, the energy performance data from the RTU and the VRF system were monitored from July 7, 2014, through February 28, 2015. Data monitoring and analysis were performed for the cooling season and heating season separately, and the calibrated simulation model was developed and used to estimate the energy performance of the RTU and VRF systems. This final report includes discussion of the design and installation of the VRF system, the data monitoring and analysis plan, the cooling season and heating season data analysis, and the building energy modeling study

  17. On-Chip Isothermal Nucleic Acid Amplification on Flow-Based Chemiluminescence Microarray Analysis Platform for the Detection of Viruses and Bacteria.

    Science.gov (United States)

    Kunze, A; Dilcher, M; Abd El Wahed, A; Hufert, F; Niessner, R; Seidel, M

    2016-01-01

    This work presents an on-chip isothermal nucleic acid amplification test (iNAAT) for the multiplex amplification and detection of viral and bacterial DNA by a flow-based chemiluminescence microarray. In a principle study, on-chip recombinase polymerase amplification (RPA) on defined spots of a DNA microarray was used to spatially separate the amplification reaction of DNA from two viruses (Human adenovirus 41, Phi X 174) and the bacterium Enterococcus faecalis, which are relevant for water hygiene. By establishing the developed assay on the microarray analysis platform MCR 3, the automation of isothermal multiplex-amplification (39 °C, 40 min) and subsequent detection by chemiluminescence imaging was realized. Within 48 min, the microbes could be identified by the spot position on the microarray while the generated chemiluminescence signal correlated with the amount of applied microbe DNA. The limit of detection (LOD) determined for HAdV 41, Phi X 174, and E. faecalis was 35 GU/μL, 1 GU/μL, and 5 × 10(3) GU/μL (genomic units), which is comparable to the sensitivity reported for qPCR analysis, respectively. Moreover the simultaneous amplification and detection of DNA from all three microbes was possible. The presented assay shows that complex enzymatic reactions like an isothermal amplification can be performed in an easy-to-use experimental setup. Furthermore, iNAATs can be potent candidates for multipathogen detection in clinical, food, or environmental samples in routine or field monitoring approaches.

  18. On the Consequences of Purging and Linkage on Fitness and Genetic Diversity

    Directory of Open Access Journals (Sweden)

    Diego Bersabé

    2016-01-01

    Full Text Available Using computer simulation we explore the consequences of linkage on the inbreeding load of an equilibrium population, and on the efficiency of purging and the loss of genetic diversity after a reduction in population size. We find that linkage tends to cause increased inbreeding load due to the build up of coupling groups of (partially recessive deleterious alleles. It also induces associative overdominance at neutral sites but rarely causes increased neutral genetic diversity in equilibrium populations. After a reduction in population size, linkage can cause some delay both for the expression of the inbreeding load and the corresponding purging. However, reasonable predictions can be obtained for the evolution of fitness under inbreeding and purging by using empirical estimates of the inbreeding depression rate. Purging selection against homozygotes for deleterious alleles affects the population’s pedigree. Furthermore, it can slow the loss of genetic diversity compared to that expected from the variance of gametic contributions to the breeding group and even from pedigree inbreeding. Under some conditions, this can lead to a smaller loss of genetic diversity, even below that expected from population size in the absence of selection.

  19. Self-filling and self-purging apparatus for detecting spontaneous radiation from substances in fluids

    Science.gov (United States)

    Larson, I. Lauren; Chiles, Marion M.; Miller, V. Clint

    1993-01-01

    Disclosed herein is a radiation detector providing for the in situ automatic sampling of fluids containing substances emitting radiation, especially Cerenkov radiation. The detector permits sampling within well casings and is self-purging such that no additional provisions must be established for the storage and disposal of contaminated fluids.

  20. The ex vivo purge of cancer cells using oncolytic viruses: recent advances and clinical implications

    Directory of Open Access Journals (Sweden)

    Tsang JJ

    2015-01-01

    Full Text Available Jovian J Tsang,1,2 Harold L Atkins2,3 1Department of Biochemistry, University of Ottawa, 2Cancer Therapeutics, Ottawa Hospital Research Institute, 3Blood and Marrow Transplant Program, The Ottawa Hospital, Ottawa, ON, Canada Abstract: Hematological malignancies are treated with intensive high-dose chemotherapy, with or without radiation. This is followed by hematopoietic stem cell (HSC transplantation (HSCT to rescue or reconstitute hematopoiesis damaged by the anticancer therapy. Autologous HSC grafts may contain cancer cells and purging could further improve treatment outcomes. Similarly, allogeneic HSCT may be improved by selectively purging alloreactive effector cells from the graft rather than wholesale immune cell depletion. Viral agents that selectively replicate in specific cell populations are being studied in experimental models of cancer and immunological diseases and have potential applications in the context of HSC graft engineering. This review describes preclinical studies involving oncolytic virus strains of adenovirus, herpes simplex virus type 1, myxoma virus, and reovirus as ex vivo purging agents for HSC grafts, as well as in vitro and in vivo experimental studies using oncolytic coxsackievirus, measles virus, parvovirus, vaccinia virus, and vesicular stomatitis virus to eradicate hematopoietic malignancies. Alternative ex vivo oncolytic virus strategies are also outlined that aim to reduce the risk of relapse following autologous HSCT and mitigate morbidity and mortality due to graft-versus-host disease in allogeneic HSCT. Keywords: hematopoietic stem cells, oncolytic virus, hematopoietic stem cell transplantation, stem cell graft purging, hematopoietic malignancy, graft vs host disease

  1. EVALUATION OF VAPOR EQUILIBRATION AND IMPACT OF PURGE VOLUME ON SOIL-GAS SAMPLING RESULTS

    Science.gov (United States)

    Sequential sampling was utilized at the Raymark Superfund site to evaluate attainment of vapor equilibration and the impact of purge volume on soil-gas sample results. A simple mass-balance equation indicates that removal of three to five internal volumes of a sample system shou...

  2. Rituximab purging and/or maintenance in patients undergoing autologous transplantation for relapsed follicular lymphoma

    DEFF Research Database (Denmark)

    Pettengell, Ruth; Schmitz, Norbert; Gisselbrecht, Christian

    2013-01-01

    The objective of this randomized trial was to assess the efficacy and safety of rituximab as in vivo purging before transplantation and as maintenance treatment immediately after high-dose chemotherapy and autologous stem-cell transplantation (HDC-ASCT) in patients with relapsed follicular lympho...

  3. Steam and fuel oil supply and purge valve with cooling steam feature

    Energy Technology Data Exchange (ETDEWEB)

    Buchanan, B.F.; Buchanan, J.R.

    1991-09-17

    This patent describes a steam and fuel oil supply and purge valve. It comprises a valve body defining steam and oil inlet ports, at least one discharge port, a steam purge passageway interconnecting the steam inlet and discharge ports, an oil supply passageway interconnecting the oil inlet and discharge ports, a cooling steam passageway interconnecting the steam inlet and discharge ports, a steam valve and actuator member movable between first, second, third, and fourth positions in the valve body and operable to open and close the steam purge and cooling steam passageways, a small metering passageway in the steam valve and actuator member which is so dimensioned and located as to open prior to full opening movement of the valve member and actuator relative to its seat, an oil valve member movable between first and second positions to open and close the oil supply passageway, biasing means urging the oil valve member toward its second and closed positions, the steam valve and actuator member in its first and second positions respectively closing and opening the steam purge passageway.

  4. Eating Patterns in Youth with Restricting and Binge Eating/Purging Type Anorexia Nervosa

    Science.gov (United States)

    Elran-Barak, Roni; Accurso, Erin C.; Goldschmidt, Andrea B.; Sztainer, Maya; Byrne, Catherine; Le Grange, Daniel

    2015-01-01

    Objective To describe eating patterns in youth with restricting and binge/purge type anorexia nervosa (AN) and to examine whether eating patterns are associated with binge eating or purging behaviors. Method Participants included 160 children and adolescents (M=15.14±2.17 years) evaluated at The University of Chicago Eating Disorders Program who met criteria for DSM-5 restrictive type AN (AN-R; 75%; n=120) or binge eating/purging type AN (AN-BE/P; 25%; n=40). All participants completed the Eating Disorder Examination (EDE) upon initial evaluation. Results Youth with AN-R and AN-BE/P differed in their eating patterns, such that youth with AN-R consumed meals and snacks more regularly relative to youth with AN-BE/P. Among youth with AN-BE/P, skipping dinner was associated with a greater number of binge eating episodes (r=−.379, p<0.05), while skipping breakfast was associated with a greater number of purging episodes (r=−.309, p<0.05). Discussion Youth with AN-R generally follow a regular meal schedule, but are likely consuming insufficient amounts of food across meals and snacks. In contrast, youth with AN-BE/P tend to have more irregular eating patterns, which may play a role in binge eating and purging behaviors. Adults monitoring of meals may be beneficial for youth with AN, and particularly those with AN-BE/P who engage in irregular eating patterns. PMID:24777645

  5. Better Fitness in Captive Cuvier's Gazelle despite Inbreeding Increase: Evidence of Purging?

    Science.gov (United States)

    Moreno, Eulalia; Pérez-González, Javier; Carranza, Juan; Moya-Laraño, Jordi

    2015-01-01

    Captive breeding of endangered species often aims at preserving genetic diversity and to avoid the harmful effects of inbreeding. However, deleterious alleles causing inbreeding depression can be purged when inbreeding persists over several generations. Despite its great importance both for evolutionary biology and for captive breeding programmes, few studies have addressed whether and to which extent purging may occur. Here we undertake a longitudinal study with the largest captive population of Cuvier's gazelle managed under a European Endangered Species Programme since 1975. Previous results in this population have shown that highly inbred mothers tend to produce more daughters, and this fact was used in 2006 to reach a more appropriate sex-ratio in this polygynous species by changing the pairing strategy (i.e., pairing some inbred females instead of keeping them as surplus individuals in the population). Here, by using studbook data we explore whether purging has occurred in the population by investigating whether after the change in pairing strategy a) inbreeding and homozygosity increased at the population level, b) fitness (survival) increased, and c) the relationship between inbreeding and juvenile survival, was positive. Consistent with the existence of purging, we found an increase in inbreeding coefficients, homozygosity and juvenile survival. In addition, we showed that in the course of the breeding programme the relationship between inbreeding and juvenile survival was not uniform but rather changed over time: it was negative in the early years, flat in the middle years and positive after the change in pairing strategy. We highlight that by allowing inbred individuals to mate in captive stocks we may favour sex-ratio bias towards females, a desirable managing strategy to reduce the surplus of males that force most zoos to use ethical culling and euthanizing management tools. We discuss these possibilities but also acknowledge that many other effects

  6. Better Fitness in Captive Cuvier's Gazelle despite Inbreeding Increase: Evidence of Purging?

    Directory of Open Access Journals (Sweden)

    Eulalia Moreno

    Full Text Available Captive breeding of endangered species often aims at preserving genetic diversity and to avoid the harmful effects of inbreeding. However, deleterious alleles causing inbreeding depression can be purged when inbreeding persists over several generations. Despite its great importance both for evolutionary biology and for captive breeding programmes, few studies have addressed whether and to which extent purging may occur. Here we undertake a longitudinal study with the largest captive population of Cuvier's gazelle managed under a European Endangered Species Programme since 1975. Previous results in this population have shown that highly inbred mothers tend to produce more daughters, and this fact was used in 2006 to reach a more appropriate sex-ratio in this polygynous species by changing the pairing strategy (i.e., pairing some inbred females instead of keeping them as surplus individuals in the population. Here, by using studbook data we explore whether purging has occurred in the population by investigating whether after the change in pairing strategy a inbreeding and homozygosity increased at the population level, b fitness (survival increased, and c the relationship between inbreeding and juvenile survival, was positive. Consistent with the existence of purging, we found an increase in inbreeding coefficients, homozygosity and juvenile survival. In addition, we showed that in the course of the breeding programme the relationship between inbreeding and juvenile survival was not uniform but rather changed over time: it was negative in the early years, flat in the middle years and positive after the change in pairing strategy. We highlight that by allowing inbred individuals to mate in captive stocks we may favour sex-ratio bias towards females, a desirable managing strategy to reduce the surplus of males that force most zoos to use ethical culling and euthanizing management tools. We discuss these possibilities but also acknowledge that many

  7. Better Fitness in Captive Cuvier’s Gazelle despite Inbreeding Increase: Evidence of Purging?

    Science.gov (United States)

    Moreno, Eulalia; Pérez-González, Javier; Carranza, Juan; Moya-Laraño, Jordi

    2015-01-01

    Captive breeding of endangered species often aims at preserving genetic diversity and to avoid the harmful effects of inbreeding. However, deleterious alleles causing inbreeding depression can be purged when inbreeding persists over several generations. Despite its great importance both for evolutionary biology and for captive breeding programmes, few studies have addressed whether and to which extent purging may occur. Here we undertake a longitudinal study with the largest captive population of Cuvier's gazelle managed under a European Endangered Species Programme since 1975. Previous results in this population have shown that highly inbred mothers tend to produce more daughters, and this fact was used in 2006 to reach a more appropriate sex-ratio in this polygynous species by changing the pairing strategy (i.e., pairing some inbred females instead of keeping them as surplus individuals in the population). Here, by using studbook data we explore whether purging has occurred in the population by investigating whether after the change in pairing strategy a) inbreeding and homozygosity increased at the population level, b) fitness (survival) increased, and c) the relationship between inbreeding and juvenile survival, was positive. Consistent with the existence of purging, we found an increase in inbreeding coefficients, homozygosity and juvenile survival. In addition, we showed that in the course of the breeding programme the relationship between inbreeding and juvenile survival was not uniform but rather changed over time: it was negative in the early years, flat in the middle years and positive after the change in pairing strategy. We highlight that by allowing inbred individuals to mate in captive stocks we may favour sex-ratio bias towards females, a desirable managing strategy to reduce the surplus of males that force most zoos to use ethical culling and euthanizing management tools. We discuss these possibilities but also acknowledge that many other effects

  8. Gas purge microsyringe extraction for quantitative direct gas chromatographic-mass spectrometric analysis of volatile and semivolatile chemicals.

    Science.gov (United States)

    Yang, Cui; Piao, Xiangfan; Qiu, Jinxue; Wang, Xiaoping; Ren, Chunyan; Li, Donghao

    2011-03-25

    Sample pretreatment before chromatographic analysis is the most time consuming and error prone part of analytical procedures, yet it is a key factor in the final success of the analysis. A quantitative and fast liquid phase microextraction technique termed as gas purge microsyringe extraction (GP-MSE) has been developed for simultaneous direct gas chromatography-mass spectrometry (GC-MS) analysis of volatile and semivolatile chemicals without cleanup process. Use of a gas flowing system, temperature control and a conventional microsyringe greatly increased the surface area of the liquid phase micro solvent, and led to quantitative recoveries of both volatile and semivolatile chemicals within short extraction time of only 2 min. Recoveries of polycyclic aromatic hydrocarbons (PAHs), organochlorine pesticides (OCPs) and alkylphenols (APs) determined were 85-107%, and reproducibility was between 2.8% and 8.5%. In particular, the technique shows high sensitivity for semivolatile chemicals which is difficult to achieve in other sample pretreatment techniques such as headspace-liquid phase microextraction. The variables affecting extraction efficiency such as gas flow rate, extraction time, extracting solvent type, temperature of sample and extracting solvent were investigated. Finally, the technique was evaluated to determine PAHs, APs and OCPs from plant and soil samples. The experimental results demonstrated that the technique is economic, sensitive to both volatile and semivolatile chemicals, is fast, simple to operate, and allows quantitative extraction. On-site monitoring of volatile and semivolatile chemicals is now possible using this technique due to the simplification and speed of sample treatment.

  9. A LabVIEW(®)-based software for the control of the AUTORAD platform: a fully automated multisequential flow injection analysis Lab-on-Valve (MSFIA-LOV) system for radiochemical analysis.

    Science.gov (United States)

    Barbesi, Donato; Vicente Vilas, Víctor; Millet, Sylvain; Sandow, Miguel; Colle, Jean-Yves; Aldave de Las Heras, Laura

    2017-01-01

    A LabVIEW(®)-based software for the control of the fully automated multi-sequential flow injection analysis Lab-on-Valve (MSFIA-LOV) platform AutoRAD performing radiochemical analysis is described. The analytical platform interfaces an Arduino(®)-based device triggering multiple detectors providing a flexible and fit for purpose choice of detection systems. The different analytical devices are interfaced to the PC running LabVIEW(®)VI software using USB and RS232 interfaces, both for sending commands and receiving confirmation or error responses. The AUTORAD platform has been successfully applied for the chemical separation and determination of Sr, an important fission product pertinent to nuclear waste.

  10. Determination of diamondoids in crude oils using gas purge microsyringe extraction with comprehensive two dimensional gas chromatography-time-of-flight mass spectrometry.

    Science.gov (United States)

    Zhang, Wanfeng; Zhu, Shukui; Pang, Liling; Gao, Xuanbo; Zhu, Gang-Tian; Li, Donghao

    2016-12-23

    Based on a homemade device, gas purge microsyringe extraction (GP-MSE) of crude oil samples was developed for the first time. As a simple, fast, low-cost, sensitive and solvent-saving technique, GP-MSE provides some outstanding advantages over the widely used sample preparation methods for crude oils such as column chromatography (ASTM D2549). Several parameters affecting extraction efficiency were optimized, including extraction temperature, extraction time, extraction solvent, condensing temperature and purge gas flow rate. With the optimized GP-MSE conditions, several real crude oil samples were extracted, and trace diamondoids were determined using comprehensive two dimensional gas chromatography-time-of-flight mass spectrometry (GC×GC-TOFMS). In total, more than 100 diamondoids were detected and 27 marker compounds were identified and quantified accurately. The limits of detection (LODs, S/N=3) were less than 0.08μg/L for all diamondoids. The relative standard deviation (RSD) was below 8%, ranging from 1.1 to 7.6%. The linearity of the developed method was in the range of 0.5-100.0μg/L with correlation coefficients (R(2)) more than 0.996. The recoveries obtained at spiking 50μg/L were between 81 and 108% for diamondoids in crude oil samples. The developed method can also be extended to the analysis of other components in crude oils and other complex matrices.

  11. Purge-and-trap isothermal multicapillary gas chromatographic sample introduction accessory for speciation of mercury by microwave-induced plasma atomic emission spectrometry.

    Science.gov (United States)

    Rodriguez Pereiro, I; Wasik, A; Lobiński, R

    1998-10-01

    A compact device based on purge-and-trap multicapillary gas chromatography was developed for sensitive species-selective analysis of methylmercury and Hg2+ by atomic spectrometry. The operating mode includes in situ conversion of the analyte species to MeEtHg and HgEt2 and cryotrapping of the derivatives formed in a 0.53-mm-i.d. capillary, followed by their flash ( 60 mL min-1) compatible with an MIP AES detector (no dilution with a makeup gas is required). Developments regarding each of the steps of the analytical procedure and effects of operational variables (sample volume, purge flow, trap temperature, separation conditions) are discussed. The device allows speciation of MeHg+ and Hg2+ down to 5 pg g-1 in urine and, after a rapid microwave-assisted hydrolysis, down to 0.1 ng g-1 in solid biological samples with a throughput of 6 samples/h. The analytical protocols developed were validated by the analysis of DORM-1 (dogfish muscle), TORT-1 (lobster hepatopancreas), and Seronorm urine certified reference materials.

  12. Interface for time-resolved introduction of gaseous analytes for atomic spectrometry by purge-and-trap multicapillary gas chromatography (PTMGC)

    Science.gov (United States)

    Wasik, Andrzej; Rodriguez Pereiro, Isaac; Łobiński, Ryszard

    1998-08-01

    A semi-automated compact interface that enables time-resolved introduction of gaseous analytes from aqueous solutions into an atomic spectrometer without the need for a full-size GC-oven is described. The interface is based on purging the gaseous analytes with an inert gas, drying the gas stream using a 30-cm tubular Nafion membrane and trapping the compounds in a thick film-coated capillary tube followed by their isothermal separation on a 1-m multicapillary GC column. Developments regarding each of the steps of the analytical procedure and effects of operational variables (sample volume, purge flow, trap temperature, speed of injection, GC separation conditions) are discussed using the speciation analysis of a mixture of tetraalkyllead compounds as an example. Recoveries are quantitative up to a sample volume of 50 ml. Figures of merit for the interface coupled to a microwave-induced plasma atomic emission detector are given. The interface allows the full speciation analysis (including sample preparation) to be carried out within less than 5 min with detection limits down to 5 pg l -1.

  13. Ionospheric plasma flow over large high-voltage space platforms. I - Ion-plasma-time scale interactions of a plate at zero angle of attack. II - The formation and structure of plasma wake

    Science.gov (United States)

    Wang, J.; Hastings, D. E.

    1992-01-01

    The paper presents the theory and particle simulation results for the ionospheric plasma flow over a large high-voltage space platform at a zero angle of attack and at a large angle of attack. Emphasis is placed on the structures in the large, high-voltage regime and the transient plasma response on the ion-plasma time scale. Special consideration is given to the transient formation of the space-charge wake and its steady-state structure.

  14. [Lens platform].

    Science.gov (United States)

    Łukaszewska-Smyk, Agnieszka; Kałuzny, Józef

    2010-01-01

    The lens platform defines lens structure and lens material. Evolution of lens comprises change in their shape, angulation of haptens and transition of three-piece lens into one-piece lens. The lens fall into two categories: rigid (PMMA) and soft (siliconic, acrylic, colameric). The main lens maaterials are polymers (hydrophilic and hydrophobic). The lens platform has an effect on biocompatibility, bioadhesion, stability of lens in capsule, degree of PCO evolution and sensitiveness to laser damages.

  15. Platform contents

    OpenAIRE

    Renault, Régis

    2014-01-01

    A monopoly platform hosts advertisers who compete on a market for horizontally differentiated products. These products may be either mass market products that appeal broadly to the entire consumer population or niche products that are tailored to the tastes of some particular group. Consumers search sequentially through ads incurring a surfing cost of moving to the next ad. They may click on an ad at some cost, which provides all relevant information and the opportunity to buy. The platform c...

  16. A Clinical Study on Haunglian Fire-Purging Mixture In Treatment of 46 Cases of Primary Hypertension

    Institute of Scientific and Technical Information of China (English)

    李运伦

    2005-01-01

    In order to observe the therapeutic effects of Huanglian Fire-Purging Mixture (黄连清降合剂) on primary hypertension, 46 cases of primary hypertension in the treatment group were treated with Huanglian Fire-Purging Mixture to clear away heat from the liver, relieve mental stress, purge fire and remove toxin;and the other 26 cases of primary hypertension in the control group were treated with Niuhuang Bolus for Lowering Blood Pressure (牛黄降压丸). The effect in the treatment group was obviously superior to that in the control group (P<0.05). The Huanglian Fire-Purging Mixture shows noticeable effects 3-6 hours after medication. The mixture can improve the clinical symptoms, the left ventricular diastolic function and myocardial ischemia, correct dyslipoproteinemia and dysglycemia, and reduce blood viscosity. And it is safe and with no obvious adverse reactions.

  17. Change in field turbidity and trace element concentrations during well purging

    Science.gov (United States)

    Gibs, J.; Szabo, Z.; Ivahnenko, T.; Wilde, F.D.

    2000-01-01

    Various physical and chemical properties were monitored sequentially in the field during well purging as indicators of stabilization of the composition of the water in the well. Turbidity was monitored on site during purging of oxic water from three wells with screened intervals open to an unconfined aquifer system in the Coastal Plain of southern New Jersey to determine if stabilization of turbidity is a reliable indicator of the optimum purge time required to collect unbiased trace element samples. Concurrent split (one filtered, one unfiltered) samples collected during purging of the wells were analyzed for concentrations of trace elements so that the relationships between trace element concentrations and turbidity could be compared. Turbidity correlated with the whole water recoverable (WWR) concentration of trace element species, such as iron (Fe), aluminum (Al), and manganese (Mn) in the oxic ground water. Turbidity appeared to be independent of other field-measured characteristics of water such as conductivity, pH, temperature, and dissolved oxygen. The WWR concentrations of lead and copper, considered to be hydrophobic, correlated significantly with the sum of the WWR concentration of Fe, Al, and Mn. High values of field-measured turbidity were a key indicator of an overestimate of ambient hydrophobic trace element WWR concentrations. Stabilization of turbidity was a better indicator of stable, unfiltered trace element concentrations than were the other commonly measured field characteristics. At one well, turbidity was a better indicator of stable, filtered trace element concentrations than the other commonly measured field characteristics. As analytical methods for trace elements improve resulting in smaller MRLs (method reporting levels) and better precision, turbidity of ground water at values of less than 10 NTU (nepheiometric turbidity units) will become important in interpreting the significance of both unfiltered and filtered sample results.

  18. The purge of spanish education during franquism (1936-1975. The institutionalization of a repression

    Directory of Open Access Journals (Sweden)

    Carlos de Pablo Lobo

    2007-09-01

    Full Text Available Work on the trial against Spanish teaching profession because of politic reasons, from the beginning of the Spanish Civil War (1936-1939 to the end of the General Francisco Franco dictatorship (1939-1975. It includes a legislation research and it also studies the reasons, institutions and the different periods in which the course is going through. Key words: Repression, Purge, Spanish teaching, Civil War, Elementary education, Franquism, Education methods. 

  19. Hepatocytes isolated from neoplastic liver-immunomagnetic purging as a new source for transplantation

    Institute of Scientific and Technical Information of China (English)

    Aravin Gunasegaram; Javed Akhter; Peng Yao; Loreena A Johnson; Stephen M Riodan; David L Morris

    2008-01-01

    AIM: To investigate whether hepatocytes isolated from macroscopically normal liver during hepatic resection for neoplasia could provide a novel source of healthy hepatocytes, including the development of reliable protocols for malignant cells removal from the hepatocyte preparation.METHODS: Hepatocytes were procured from resected liver of 18 patients with liver tumors using optimised digestion and cell-enrichment protocols. Suspensions of various known quantities of the HT-29 tumor cell line and patient hepatocytes were treated or not with Ep-CAM-antibody-coated immunomagnetic beads in order to investigate the efficacy of tumor-purging by immunomagnetic depletion, using a semi-quantitative RT-PCR method developed to detect tumor cells.Immunomagnetic bead-treated or bead-untreated tumor cell-hepatocyte suspensions were transplanted intra-peritoneally in Balb/C nude mice to assess the rates of tumor development.RESULTS: Mean viable hepatocyte yield was 9.3 x 106 cells per gram of digested liver with mean viability of 70.5%. Immunomagnetic depletion removed tumor cells to below the RT-PCR detection-threshold of 1 tumor cell in 106 hepatocytes, representing a maximum tumor purging efficacy of greater than 400000-fold.Transplanted, immunomagnetic bead-purged tumor cell-hepatocyte suspensions did not form peritoneal tumors in Balb/C nude mice. Co-transplantation of hepatocytes with tumor cells did not increase tumorigenesis of the tumor cells.CONCLUSION: Immunomagnetic depletion appears to be an effective method of purging contaminating tumor cells to below threshold for likely tumorigenesis.Along with improved techniques for isolation of large numbers of viable hepatocytes, normal liver resected for neoplasia has potential as another clinically useful source of hepatocytes for transplantation.

  20. Lifetime inbreeding depression, purging, and mating system evolution in a simultaneous hermaphrodite tapeworm.

    Science.gov (United States)

    Benesh, Daniel P; Weinreich, Friederike; Kalbe, Martin; Milinski, Manfred

    2014-06-01

    Classical theory on mating system evolution suggests that simultaneous hermaphrodites should either outcross if they have high inbreeding depression (ID) or self-fertilize if they have low ID. However, a mixture of selfing and outcrossing persists in many species. Previous studies with the tapeworm Schistocephalus solidus have found worms to self-fertilize some of their eggs despite ID. The probability for selfing to spread depends on the relative fitness of selfers, as well as the genetic basis for ID and whether it can be effectively purged. We bred S. solidus through two consecutive generations of selfing and recorded several fitness correlates over the whole life cycle. After one round of selfing, ID was pronounced, particularly in early-life traits, and the conservatively estimated lifetime fitness of selfed progeny was only 9% that of the outcrossed controls. After a second generation of selfing, ID remained high but was significantly reduced in several traits, which is consistent with the purging of deleterious recessive alleles (the estimated load of lethal equivalents dropped by 48%). Severe ID, even if it can be rapidly purged, likely prevents transitions toward pure selfing in this parasite, although we also cannot exclude the possibility that low-level selfing has undetected benefits.

  1. Acute gastric dilatation in a patient with anorexia nervosa binge/purge subtype.

    Science.gov (United States)

    Tweed-Kent, Ailis M; Fagenholz, Peter J; Alam, Hasan B

    2010-10-01

    Acute gastric dilatation is a rare complication of anorexia nervosa binge/purge subtype that results from gastrointestinal abnormalities, including decreased gastric motility and delayed gastric emptying. Early diagnosis and intervention is critical since delay may result in gastric necrosis, perforation, shock, and death. We report a 26-year-old female with anorexia nervosa binge/purge subtype, who presented with abdominal pain and nausea after a binge episode. Abdominal radiography and computed tomography showed a grossly dilated stomach measuring 32 cm × 17.9 cm consistent with acute gastric dilatation. She underwent exploratory laparotomy with gastrotomy and gastric decompression, and recovered uneventfully. Initially, the patient denied the binge episode, as many patients with eating disorders do, but later revealed an extensive history of anorexia nervosa binge/purge subtype. This case stresses the importance of obtaining a thorough history of eating disorders and maintaining a high index of suspicion for acute gastric dilatation in young women who present with abdominal pain and distention.

  2. The ex vivo purge of cancer cells using oncolytic viruses: recent advances and clinical implications.

    Science.gov (United States)

    Tsang, Jovian J; Atkins, Harold L

    2015-01-01

    Hematological malignancies are treated with intensive high-dose chemotherapy, with or without radiation. This is followed by hematopoietic stem cell (HSC) transplantation (HSCT) to rescue or reconstitute hematopoiesis damaged by the anticancer therapy. Autologous HSC grafts may contain cancer cells and purging could further improve treatment outcomes. Similarly, allogeneic HSCT may be improved by selectively purging alloreactive effector cells from the graft rather than wholesale immune cell depletion. Viral agents that selectively replicate in specific cell populations are being studied in experimental models of cancer and immunological diseases and have potential applications in the context of HSC graft engineering. This review describes preclinical studies involving oncolytic virus strains of adenovirus, herpes simplex virus type 1, myxoma virus, and reovirus as ex vivo purging agents for HSC grafts, as well as in vitro and in vivo experimental studies using oncolytic coxsackievirus, measles virus, parvovirus, vaccinia virus, and vesicular stomatitis virus to eradicate hematopoietic malignancies. Alternative ex vivo oncolytic virus strategies are also outlined that aim to reduce the risk of relapse following autologous HSCT and mitigate morbidity and mortality due to graft-versus-host disease in allogeneic HSCT.

  3. Gas purge-microsyringe extraction: a rapid and exhaustive direct microextraction technique of polycyclic aromatic hydrocarbons from plants.

    Science.gov (United States)

    Wang, Juan; Yang, Cui; Li, Huijie; Piao, Xiangfan; Li, Donghao

    2013-12-17

    Gas purge-microsyringe extraction (GP-MSE) is a rapid and exhaustive microextraction technique for volatile and semivolatile compounds. In this study, a theoretical system of GP-MSE was established by directly extracting and analyzing 16 kinds of polycyclic aromatic hydrocarbons (PAHs) from plant samples. On the basis of theoretical consideration, a full factorial experimental design was first used to evaluate the main effects and interactions of the experimental parameters affecting the extraction efficiency. Further experiments were carried out to determine the extraction kinetics and desorption temperature-dependent. The results indicated that three factors, namely desorption temperature (temperature of sample phase) Td, extraction time t, and gas flow rate u, had a significantly positive effect on the extraction efficiency of GP-MSE for PAHs. Extraction processes of PAHs in plant samples followed by first-order kinetics (relative coefficient R(2) of simulation curves were 0.731-1.000, with an average of 0.958 and 4.06% relative standard deviation), and obviously depended on the desorption temperature. Furthermore, the effect of the matrix was determined from the difference in Eapp,d. Finally, satisfactory recoveries of 16 PAHs were obtained using optimal parameters. The study demonstrated that GP-MSE could provide a rapid and exhaustive means of direct extraction of PAHs from plant samples. The extraction kinetics were similar that of the inverse process of the desorption kinetics of the sample phase.

  4. The influence of purge times on the yields of essential oil components extracted from plants by pressurized liquid extraction.

    Science.gov (United States)

    Wianowska, Dorota

    2014-01-01

    The influence of different purge times on the yield of the main essential oil constituents of rosemary (Rosmarinus officinalis L.), thyme (Thymus vulgaris L.), and chamomile (Chamomilla recutita L.) was investigated. The pressurized liquid extraction process was performed by applying different extraction temperatures and solvents. The results presented in the paper show that the estimated yield of essential oil components extracted from the plants in the pressurized liquid extraction process is purge time-dependent. The differences in the estimated yields are mainly connected with the evaporation of individual essential oil components and the applied solvent during the purge; the more volatile an essential oil constituent is, the greater is its loss during purge time, and the faster the evaporation of the solvent during the purge process is, the higher the concentration of less volatile essential oil components in the pressurized liquid extraction receptacle. The effect of purge time on the estimated yield of individual essential oil constituents is additionally differentiated by the extraction temperature and the extraction ability of the applied solvent.

  5. ITS Platform

    DEFF Research Database (Denmark)

    Tøfting, Svend; Lahrmann, Harry; Agerholm, Niels

    2014-01-01

    Aalborg University and two local companies have over the past four years developed and tested an ITS Platform, which can be used for communication with cars and for providing a number of services to the drivers. The purpose has been to perform a technological test of the possible use of a hidden ...... not have to be very intelligent. This is gradually taken over by applications on smart phones. The ITS Platform with 425 test drivers is now completely developed and can be used for technological testing of e.g. payment systems.......Aalborg University and two local companies have over the past four years developed and tested an ITS Platform, which can be used for communication with cars and for providing a number of services to the drivers. The purpose has been to perform a technological test of the possible use of a hidden...

  6. ITS Platform

    DEFF Research Database (Denmark)

    Tøfting, Svend; Lahrmann, Harry; Agerholm, Niels

    2014-01-01

    Aalborg University and two local companies have over the past four years developed and tested an ITS Platform, which can be used for communication with cars and for providing a number of services to the drivers. The purpose has been to perform a technological test of the possible use of a hidden ...... not have to be very intelligent. This is gradually taken over by applications on smart phones. The ITS Platform with 425 test drivers is now completely developed and can be used for technological testing of e.g. payment systems....

  7. Dynamic Establishment of E-commerce Transaction Platform Based on Web Service and Work Flow%基于Web service与工作流的电子商务交易平台动态构建

    Institute of Scientific and Technical Information of China (English)

    戴伟

    2013-01-01

    In this paper,on the basis of Web-service and work-flow modeling technology,we proposed a method for the dynamic establishment of the e-commerce transaction platform,which encapsulated functional modules of the platform as Web-service applications,divided the transaction page into templates and used the work-flow modeling method to describe the process of the transactions,thus facilitating dynamic establishment of the platform by altering the process model or the tasks bound in the process.%基于Web service与工作流建模技术提出一种电子商务交易平台动态构建方法,交易平台中的功能模块被封装为Web service应用程序,将交易页面进行模板区域划分,采取工作流建模的方式对交易流程进行刻画,从而可以通过修改流程模型或者流程中绑定的任务来实现交易平台的动态重构.

  8. Platform computing

    CERN Multimedia

    2002-01-01

    "Platform Computing releases first grid-enabled workload management solution for IBM eServer Intel and UNIX high performance computing clusters. This Out-of-the-box solution maximizes the performance and capability of applications on IBM HPC clusters" (1/2 page) .

  9. 旋转式明渠流综合实验平台研制与应用%Development and application of comprehensive experiment platform for rotatable open channel flow

    Institute of Scientific and Technical Information of China (English)

    戎贵文; 袁岳; 肖柏青; 许光泉

    2015-01-01

    In order to cultivate the innovative ability of college students and overcome the disadvantages in the experiment device of single open channel flow,such as simple experiment content,occupation of large area,and high cost,a comprehensive experi-ment platform for rotatable open channel flow was developed based on the conventional hydraulic experiment apparatus and bas-ic principle of fluid flow.The experiment platform used the rotatable method to integrate different open channel flow experi-ments,which can meet the demand of conducting various conventional open channel flow experiments in the same platform,and the demand of modern teaching including the comprehensive,designed,and innovative training plans.The platform has the ad-vantages of perfect design,complete function,and convenient reestablishment,which is of important significance for the cultiva-tion of innovative talents with water conservancy major.%为了培养大学生创新能力和克服单个明渠流实验装置测试内容单一、占地大、成本高等缺陷,在研究传统水力学实验装置和流体运动基本原理的基础上,自主研制开发了一套旋转式明渠流综合实验平台。该实验平台采用旋转方式创造性地将多种明渠水流实验集为一身,能够满足学生在同一实验平台上进行多种常规明渠流实验的需求,从而满足高校综合性、设计性、创新创业训练计划等现代教学的要求。实践表明,该实验平台具有设计巧妙、功能齐全、改造方便等优点,对水利类专业构建创新型人才培养模式有重要意义。

  10. DISSOLUTION OF IRRADIATED MURR FUEL ASSEMBLIES EFFECT OF INCREASED PURGE RATE AND CATALYST CONCENTRATION ON THE BATCH SIZE

    Energy Technology Data Exchange (ETDEWEB)

    Kyser, E.

    2010-07-22

    Flowsheets for the dissolution of aluminum-clad spent nuclear fuel have been proposed using 0.002 M mercuric nitrate catalyst in 5 to 6 M nitric acid. Previous calculations for flammable gas control during the dissolution of spent nuclear fuel have been extended to cover a range of dissolver purge rates from 40 to 55 scfm. A range of dissolver solution volumes from 12000 to 15000 liters were considered for the large H-Canyon dissolver (6.4D). Depending on the purge rate, anywhere from four to six bundles of MURR fuel can be initially charged to the dissolver (6.4D). For successive charges where the dissolver solution already contains 0.002 M mercury catalyst and the dissolved aluminum from five bundles of MURR fuel, five to nine bundles of additional fuel can be charged depending on the purge rate and the dissolver solution volume. Similar calculations have been performed for the small H-Canyon dissolver (6.1D) for solution volumes that ranged from 6000 to 7500 liters and purge rates from 40 to 55 scfm. The limitations on the initial charge are four to six bundles depending on the purge rate. The aluminum from four bundles of fuel in an initial charge will allow nine to ten bundles in the second charge to 6.1D depending on the purge rate and dissolver solution volume. Solubility or criticality limitations will restrict the second charge on the small dissolver. The concentration of aluminum from previous charges will slow the dissolution rate to extend the cycle time of repeated charges of fuel. Calculations have been performed to allow a second catalyst addition (up to 0.004 M total catalyst) to reduce the cycle time (as necessary) based on the aluminum concentration and the purge rate.

  11. Comparison of no-purge and pumped sampling methods for monitoring concentrations of ordnance-related compounds in groundwater, Camp Edwards, Massachusetts Military Reservation, Cape Cod, Massachusetts, 2009-2010

    Science.gov (United States)

    Savoie, Jennifer G.; LeBlanc, Denis R.

    2012-01-01

    Field tests were conducted near the Impact Area at Camp Edwards on the Massachusetts Military Reservation, Cape Cod, Massachusetts, to determine the utility of no-purge groundwater sampling for monitoring concentrations of ordnance-related explosive compounds and perchlorate in the sand and gravel aquifer. The no-purge methods included (1) a diffusion sampler constructed of rigid porous polyethylene, (2) a diffusion sampler constructed of regenerated-cellulose membrane, and (3) a tubular grab sampler (bailer) constructed of polyethylene film. In samples from 36 monitoring wells, concentrations of perchlorate (ClO4-), hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX), and octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX), the major contaminants of concern in the Impact Area, in the no-purge samples were compared to concentrations of these compounds in samples collected by low-flow pumped sampling with dedicated bladder pumps. The monitoring wells are constructed of 2- and 2.5-inch-diameter polyvinyl chloride pipe and have approximately 5- to 10-foot-long slotted screens. The no-purge samplers were left in place for 13-64 days to ensure that ambient groundwater flow had flushed the well screen and concentrations in the screen represented water in the adjacent formation. The sampling methods were compared first in six monitoring wells. Concentrations of ClO4-, RDX, and HMX in water samples collected by the three no-purge sampling methods and low-flow pumped sampling were in close agreement for all six monitoring wells. There is no evidence of a systematic bias in the concentration differences among the methods on the basis of type of sampling device, type of contaminant, or order in which the no-purge samplers were tested. A subsequent examination of vertical variations in concentrations of ClO4- in the 10-foot-long screens of six wells by using rigid porous polyethylene diffusion samplers indicated that concentrations in a given well varied by less than 15 percent

  12. Module bay with directed flow

    Science.gov (United States)

    Torczynski, John R.

    2001-02-27

    A module bay requires less cleanroom airflow. A shaped gas inlet passage can allow cleanroom air into the module bay with flow velocity preferentially directed toward contaminant rich portions of a processing module in the module bay. Preferential gas flow direction can more efficiently purge contaminants from appropriate portions of the module bay, allowing a reduced cleanroom air flow rate for contaminant removal. A shelf extending from an air inlet slit in one wall of a module bay can direct air flowing therethrough toward contaminant-rich portions of the module bay, such as a junction between a lid and base of a processing module.

  13. Platform Constellations

    DEFF Research Database (Denmark)

    Staykova, Kalina Stefanova; Damsgaard, Jan

    2016-01-01

    messaging apps KakaoTalk and LINE, we are able to gain valuable insights about the nature of these new constructions and to capture and synthesize their main characteristics in a framework. Our results show that platform constellations possess unique innovative capabilities, which can improve users......’ acquisition and users’ engagement rates as well as unlock new sources of value creation and diversify revenue streams....

  14. Experimental Platform Design on Flowing Resistance of Air Vents for Bullet Train%高速动车换气口流动阻力实验台设计

    Institute of Scientific and Technical Information of China (English)

    何忠韬; 方海容

    2013-01-01

    探讨了高速动车换气口流动阻力实验台相关问题,根据流体力学相关原理,提出用低速风洞模拟列车外界风速场,换气口试件置于风洞试验段中,将列车外界风速、流经换气口的风量模拟量都设计成可调控的实验参数,搭建了用于换气口流动阻力及其影响因素的实验平台。实验实例表明,本文方法建立的高速动车换气口流动阻力实验台方案是可行的,测量结果是可信的。%Problems about an experimental platform are discussed,recurring to which,the flowing resistance of air vents on the bullet train can be researched.According to the principle of fluid mechanics,it is put forward that the train wind field outside can be simulated by the low speed wind tunnel,the ventilation test piece is placed in the test section of wind tunnel,the wind speed outside and the flowing rate through the air vents are tunable,then a experimental platform for flowing resistance of air vents is built.The experimental results show that the scheme of the experimental platform is feasible,and the measurement results are credible.

  15. Cryogenic system with GM cryocooler for krypton, xenon separation from hydrogen-helium purge gas

    Energy Technology Data Exchange (ETDEWEB)

    Chu, X. X.; Zhang, D. X.; Qian, Y.; Liu, W. [Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Shanghai, 201800 (China); Zhang, M. M.; Xu, D. [Technical Institute of Physics and Chemistry, Chinese Academy of Sciences, Beijing, 100190 (China)

    2014-01-29

    In the thorium molten salt reactor (TMSR), fission products such as krypton, xenon and tritium will be produced continuously in the process of nuclear fission reaction. A cryogenic system with a two stage GM cryocooler was designed to separate Kr, Xe, and H{sub 2} from helium purge gas. The temperatures of two stage heat exchanger condensation tanks were maintained at about 38 K and 4.5 K, respectively. The main fluid parameters of heat transfer were confirmed, and the structural heat exchanger equipment and cold box were designed. Designed concentrations after cryogenic separation of Kr, Xe and H{sub 2} in helium recycle gas are less than 1 ppb.

  16. Cryogenic system with GM cryocooler for krypton, xenon separation from hydrogen-helium purge gas

    Science.gov (United States)

    Chu, X. X.; Zhang, M. M.; Zhang, D. X.; Xu, D.; Qian, Y.; Liu, W.

    2014-01-01

    In the thorium molten salt reactor (TMSR), fission products such as krypton, xenon and tritium will be produced continuously in the process of nuclear fission reaction. A cryogenic system with a two stage GM cryocooler was designed to separate Kr, Xe, and H2 from helium purge gas. The temperatures of two stage heat exchanger condensation tanks were maintained at about 38 K and 4.5 K, respectively. The main fluid parameters of heat transfer were confirmed, and the structural heat exchanger equipment and cold box were designed. Designed concentrations after cryogenic separation of Kr, Xe and H2 in helium recycle gas are less than 1 ppb.

  17. Measurement of residual solvents in a drug substance by a purge-and-trap method.

    Science.gov (United States)

    Lakatos, Miklós

    2008-08-05

    The purge-and-trap (P&T) gas extraction method combined with gas chromatography was studied for its suitability for quantitative residual solvents determination in a water-soluble active pharmaceutical ingredient (API). Some analytical method performance characteristics were investigated, namely, the repeatability, the accuracy and the detection limit of determination. The results show that the P&T technique is--as expected--more sensitive than the static headspace, thus it can be used for the determination of residual solvents pertaining to the ICH Class 1 group. It was found that it could be an alternative sample preparation method besides the static headspace (HS) method.

  18. 云平台上海洋服务流定制的可视化建模研究%Visualized modeling technology research of service-flow based on cloud platform

    Institute of Scientific and Technical Information of China (English)

    杜金峰; 东韩; 徐凌宇; 陈亮; 蔡茂

    2013-01-01

    Using now existing marine information processing models and other related resources to design marine service-flow architecture, users can customize individual marine service-flows. By visualization modeling technology, service-flow definition, model analysis and interaction of flows are realized. Users have access to various model services on the Internet. Service-flow page is the only entry to customize service-flows. On this page, marine data and model resources are provided with visual customizing methods. At last service-flows are defined automatically in this system by visual modeling technology and the flow description are submitted to cloud platform for implementation, then the results are given back to users.%利用已有的海洋信息处理模型及相关资源,开展基于云平台的海洋服务流架构设计,实现个性化的海洋服务流定制.通过可视化建模技术实现服务流定义,模型分析,服务流的交互式执行.用户只需要通过网络即可访问云平台中提供的各种模型服务.其中服务流页面作为定制服务流的唯一访问点,可视化地提供了云平台上的海洋数据模型资源和图形化的定制方法,将服务流描述提交给云平台,完成用户的个性化的服务定制执行.

  19. Apoptotic susceptibility to DNA damage of pluripotent stem cells facilitates pharmacologic purging of teratoma risk.

    Science.gov (United States)

    Smith, Alyson J; Nelson, Natalie G; Oommen, Saji; Hartjes, Katherine A; Folmes, Clifford D; Terzic, Andre; Nelson, Timothy J

    2012-10-01

    Pluripotent stem cells have been the focus of bioengineering efforts designed to generate regenerative products, yet harnessing therapeutic capacity while minimizing risk of dysregulated growth remains a challenge. The risk of residual undifferentiated stem cells within a differentiated progenitor population requires a targeted approach to eliminate contaminating cells prior to delivery. In this study we aimed to validate a toxicity strategy that could selectively purge pluripotent stem cells in response to DNA damage and avoid risk of uncontrolled cell growth upon transplantation. Compared with somatic cell types, embryonic stem cells and induced pluripotent stem cells displayed hypersensitivity to apoptotic induction by genotoxic agents. Notably, hypersensitivity in pluripotent stem cells was stage-specific and consistently lost upon in vitro differentiation, with the mean half-maximal inhibitory concentration increasing nearly 2 orders of magnitude with tissue specification. Quantitative polymerase chain reaction and Western blotting demonstrated that the innate response was mediated through upregulation of the BH3-only protein Puma in both natural and induced pluripotent stem cells. Pretreatment with genotoxic etoposide purged hypersensitive pluripotent stem cells to yield a progenitor population refractory to teratoma formation upon transplantation. Collectively, this study exploits a hypersensitive apoptotic response to DNA damage within pluripotent stem cells to decrease risk of dysregulated growth and augment the safety profile of transplant-ready, bioengineered progenitor cells.

  20. Purge and trap with monolithic sorbent for gas chromatographic analysis of pesticides in honey.

    Science.gov (United States)

    Chienthavorn, Orapin; Dararuang, Kanittha; Sasook, Anupop; Ramnut, Narumol

    2012-01-01

    Polydivinylbenzene (P-DVB) and silica monolithic materials were synthesised in capillaries and then used to adsorb nine organonitrogen pesticides extracted from honey. After adsorption, each monolith-capillary was connected to a gas chromatograph (GC) with nitrogen-phosphorous detector (NPD). The silica monolith gave better peak shape and intensity than the P-DVB monolith. Formulation of silica monolith with tetramethoxysilane (TMOS) as a sole initiator provided better separation and higher peak intensity, compared to those with methyltrimethoxysilane (MTMS) and (3:1) TMOS/MTMS initiators. The optimum internal diameter and length of silica monolith-capillary were 0.25 mm and 5 cm, respectively. The purge and trap conditions were optimised by purging with nitrogen and heating the honey sample solution at 100 °C for 60 min. Recovery of the method was in a range of 84.95-99.71% and the detection limits of the pesticides determined by using GC-NPD and GC-mass spectrometric detector (MSD) ranged between 0.36-1.75 and 0.13-0.25 ng g(-1), respectively.

  1. Determination of cyclic volatile methylsiloxanes in biota with a purge and trap method.

    Science.gov (United States)

    Kierkegaard, Amelie; Adolfsson-Erici, Margaretha; McLachlan, Michael S

    2010-11-15

    The three cyclic volatile methylsiloxanes (cVMS), octamethylcyclotetrasiloxane (D4), decamethylcyclopentasiloxane (D5), and dodecamethylcyclohexasiloxane (D6), are recently identified environmental contaminants. Methods for the trace analysis of these chemicals in environmental matrices are required. A purge and trap method to prepare highly purified sample extracts with a low risk of sample contamination is presented. Without prior homogenization, the sample is heated in water, and the cVMS are purged from the slurry and trapped on an Isolute ENV+ cartridge. They are subsequently eluted with n-hexane and analyzed with GC/MS. The method was tested for eight different matrices including ragworms, muscle tissue from lean and lipid-rich fish, cod liver, and seal blubber. Analyte recoveries were consistent within and between matrices, averaging 79%, 68%, and 56% for D4, D5, and D6, respectively. Good control of blank levels resulted in limits of quantification of 1.5, 0.6, and 0.6 ng/g wet weight. The repeatability was 12% (D5) and 15% (D6) at concentrations 9 and 2 times above the LOQ. The method was applied to analyze cVMS in fish from Swedish lakes, demonstrating that contamination in fish as a result of long-range atmospheric transport is low as compared to contamination from local sources.

  2. Determination of phosphine: comparison of rates of desorption by purge-and-trap method and by sulfuric acid treatment.

    Science.gov (United States)

    Saeed, T; Abu-Tabanja, R

    1985-01-01

    Two methods were compared for quantitative determination of phosphine present on fumigated food and materials. The rate of desorption of PH3 by using a purge-and-trap method was shown to be much slower when compared with sulfuric acid treatment and was also simpler. Application of the modified sulfuric acid treatment for real samples is described.

  3. Influence of negative affect on decision making in women with restrictive and binge-purge type anorexia nervosa

    NARCIS (Netherlands)

    Danner, Unna N; Sternheim, Lot; Bijsterbosch, Jojanneke M; Dingemans, Alexandra E; Evers, Catharine; van Elburg, Annemarie A

    2016-01-01

    The present study aims to examine the influence of negative affect on decision making in women with anorexia nervosa (AN) compared to healthy control women and, secondly, to assess differences between the restrictive (ANR) and binge-purge (ANBP) subtypes. One hundred four women (32 with ANR, 32 with

  4. Purging deleterious mutations under self fertilization: paradoxical recovery in fitness with increasing mutation rate in Caenorhabditis elegans.

    Directory of Open Access Journals (Sweden)

    Levi T Morran

    Full Text Available BACKGROUND: The accumulation of deleterious mutations can drastically reduce population mean fitness. Self-fertilization is thought to be an effective means of purging deleterious mutations. However, widespread linkage disequilibrium generated and maintained by self-fertilization is predicted to reduce the efficacy of purging when mutations are present at multiple loci. METHODOLOGY/PRINCIPAL FINDINGS: We tested the ability of self-fertilizing populations to purge deleterious mutations at multiple loci by exposing obligately self-fertilizing populations of Caenorhabditis elegans to a range of elevated mutation rates and found that mutations accumulated, as evidenced by a reduction in mean fitness, in each population. Therefore, purging in obligate selfing populations is overwhelmed by an increase in mutation rate. Surprisingly, we also found that obligate and predominantly self-fertilizing populations exposed to very high mutation rates exhibited consistently greater fitness than those subject to lesser increases in mutation rate, which contradicts the assumption that increases in mutation rate are negatively correlated with fitness. The high levels of genetic linkage inherent in self-fertilization could drive this fitness increase. CONCLUSIONS: Compensatory mutations can be more frequent under high mutation rates and may alleviate a portion of the fitness lost due to the accumulation of deleterious mutations through epistatic interactions with deleterious mutations. The prolonged maintenance of tightly linked compensatory and deleterious mutations facilitated by self-fertilization may be responsible for the fitness increase as linkage disequilibrium between the compensatory and deleterious mutations preserves their epistatic interaction.

  5. Increases in frontostriatal connectivity are associated with response to dorsomedial repetitive transcranial magnetic stimulation in refractory binge/purge behaviors

    Directory of Open Access Journals (Sweden)

    Katharine Dunlop

    2015-01-01

    Conclusions: Enhanced frontostriatal connectivity was associated with responders to dmPFC-rTMS for binge/purge behavior. rTMS caused paradoxical suppression of frontostriatal connectivity in nonresponders. rs-fMRI could prove critical for optimizing stimulation parameters in a future sham-controlled trial of rTMS in disordered eating.

  6. Seasonal patterns of birth for subjects with bulimia nervosa, binge eating, and purging: results from the National Women's Study.

    Science.gov (United States)

    Brewerton, Timothy D; Dansky, Bonnie S; O'Neil, Patrick M; Kilpatrick, Dean G

    2012-01-01

    Studies of birth patterns in anorexia nervosa have shown relative increases between March and August, while studies in Bulimia Nervosa (BN) have been negative. Since there are no studies using representative, nonclinical samples, we looked for seasonal birth patterns in women with BN and in those who ever endorsed bingeing or purging. A national, representative sample of 3,006 adult women completed structured telephone interviews including screenings for bulimia nervosa (BN) and questions about month, date, and year of birth. Season of birth was calculated using traditional definitions. Differences across season of birth between subjects with (n = 85) and without BN (n = 2,898), those with (n = 749) and without bingeing (n = 2,229), and those with (n = 267) and without any purging (n = 2,715) were compared using chi-square analyses. There were significant differences across season of birth between subjects: (1) with and without BN (p = 0.033); (2) with and without bingeing (p = 0.034), and; (3) with and without purging (p = 0.001). Fall had the highest relative number of births for all categories, while spring had the lowest. In a national representative study of nontreatment seeking subjects significant differences in season of birth were found for subjects with lifetime histories of BN, binge eating and purging. © 2011 by Wiley Periodicals, Inc. (Int J Eat Disord 2012). Copyright © 2011 Wiley Periodicals, Inc.

  7. Enhanced selectivity of hyperthermic purging of human progenitor cells using Goralatide, an inhibitor of cell cycle progression

    NARCIS (Netherlands)

    Wierenga, PK; Brenner, MK; Konings, AWT

    1998-01-01

    Recurrence of leukemia is a major problem after autologous stem cell transplantation. One potential means of reducing this risk is to purge the autologous transplant in vitro by hyperthermia, We have demonstrated that after a hyperthermic treatment of 120 min at 43 degrees C, the leukemic progenitor

  8. Identification of Aroma Compounds of Lamiaceae Species in Turkey Using the Purge and Trap Technique

    Directory of Open Access Journals (Sweden)

    Ahmet Salih Sonmezdag

    2017-02-01

    Full Text Available The present research was planned to characterize the aroma composition of important members of the Lamiaceae family such as Salvia officinalis, Lavandula angustifolia and Mentha asiatica. Aroma components of the S. officinalis, L. angustifolia and M. asiatica were extracted with the purge and trap technique with dichloromethane and analyzed with the gas chromatography–mass spectrometry (GC–MS technique. A total of 23, 33 and 33 aroma compounds were detected in Salvia officinalis, Lavandula angustifolia and Mentha asiatica, respectively including, acids, alcohols, aldehydes, esters, hydrocarbons and terpenes. Terpene compounds were both qualitatively and quantitatively the major chemical group among the identified aroma compounds, followed by esters. The main terpene compounds were 1,8-cineole, sabinene and linalool in Salvia officinalis, Lavandula angustifolia and Mentha asiatica, respectively. Among esters, linalyl acetate was the only and most important ester compound which was detected in all samples.

  9. Identification of Aroma Compounds of Lamiaceae Species in Turkey Using the Purge and Trap Technique.

    Science.gov (United States)

    Sonmezdag, Ahmet Salih; Kelebek, Hasim; Selli, Serkan

    2017-02-08

    The present research was planned to characterize the aroma composition of important members of the Lamiaceae family such as Salvia officinalis, Lavandula angustifolia and Mentha asiatica. Aroma components of the S. officinalis, L. angustifolia and M. asiatica were extracted with the purge and trap technique with dichloromethane and analyzed with the gas chromatography-mass spectrometry (GC-MS) technique. A total of 23, 33 and 33 aroma compounds were detected in Salvia officinalis, Lavandula angustifolia and Mentha asiatica, respectively including, acids, alcohols, aldehydes, esters, hydrocarbons and terpenes. Terpene compounds were both qualitatively and quantitatively the major chemical group among the identified aroma compounds, followed by esters. The main terpene compounds were 1,8-cineole, sabinene and linalool in Salvia officinalis, Lavandula angustifolia and Mentha asiatica, respectively. Among esters, linalyl acetate was the only and most important ester compound which was detected in all samples.

  10. Identification of Aroma Compounds of Lamiaceae Species in Turkey Using the Purge and Trap Technique

    Science.gov (United States)

    Sonmezdag, Ahmet Salih; Kelebek, Hasim; Selli, Serkan

    2017-01-01

    The present research was planned to characterize the aroma composition of important members of the Lamiaceae family such as Salvia officinalis, Lavandula angustifolia and Mentha asiatica. Aroma components of the S. officinalis, L. angustifolia and M. asiatica were extracted with the purge and trap technique with dichloromethane and analyzed with the gas chromatography–mass spectrometry (GC–MS) technique. A total of 23, 33 and 33 aroma compounds were detected in Salvia officinalis, Lavandula angustifolia and Mentha asiatica, respectively including, acids, alcohols, aldehydes, esters, hydrocarbons and terpenes. Terpene compounds were both qualitatively and quantitatively the major chemical group among the identified aroma compounds, followed by esters. The main terpene compounds were 1,8-cineole, sabinene and linalool in Salvia officinalis, Lavandula angustifolia and Mentha asiatica, respectively. Among esters, linalyl acetate was the only and most important ester compound which was detected in all samples. PMID:28231089

  11. Spent nuclear fuel project cold vacuum drying facility vacuum and purge system design description

    Energy Technology Data Exchange (ETDEWEB)

    IRWIN, J.J.

    1998-11-30

    This document provides the System Design Description (SDD) for the Cold Vacuum Drying Facility (CVDF) Vacuum and Purge System (VPS) . The SDD was developed in conjunction with HNF-SD-SNF-SAR-O02, Safety Analysis Report for the Cold Vacuum Drying Facility, Phase 2, Supporting Installation of Processing Systems (Garvin 1998), The HNF-SD-SNF-DRD-002, 1998, Cold Vacuum Drying Facility Design Requirements, and the CVDF Design Summary Report. The SDD contains general descriptions of the VPS equipment, the system functions, requirements and interfaces. The SDD provides references for design and fabrication details, operation sequences and maintenance. This SDD has been developed for the SNFP Operations Organization and shall be updated, expanded, and revised in accordance with future design, construction and startup phases of the CVDF until the CVDF final ORR is approved.

  12. Reliable and accurate CD4+ T cell count and percent by the portable flow cytometer CyFlow MiniPOC and "CD4 Easy Count Kit-Dry", as revealed by the comparison with the gold standard dual platform technology.

    Directory of Open Access Journals (Sweden)

    Milena Nasi

    Full Text Available An accurate and affordable CD4+ T cells count is an essential tool in the fight against HIV/AIDS. Flow cytometry (FCM is the "gold standard" for counting such cells, but this technique is expensive and requires sophisticated equipment, temperature-sensitive monoclonal antibodies (mAbs and trained personnel. The lack of access to technical support and quality assurance programs thus limits the use of FCM in resource-constrained countries. We have tested the accuracy, the precision and the carry-over contamination of Partec CyFlow MiniPOC, a portable and economically affordable flow cytometer designed for CD4+ count and percentage, used along with the "CD4% Count Kit-Dry".Venous blood from 59 adult HIV+ patients (age: 25-58 years; 43 males and 16 females was collected and stained with the "MiniPOC CD4% Count Kit-Dry". CD4+ count and percentage were then determined in triplicate by the CyFlow MiniPOC. In parallel, CD4 count was performed using mAbs and a CyFlow Counter, or by a dual platform system (from Beckman Coulter based upon Cytomic FC500 ("Cytostat tetrachrome kit" for mAbs and Coulter HmX Hematology Analyzer (for absolute cell count.The accuracy of CyFlow MiniPOC against Cytomic FC500 showed a correlation coefficient (CC of 0.98 and 0.97 for CD4+ count and percentage, respectively. The accuracy of CyFlow MiniPOC against CyFlow Counter showed a CC of 0.99 and 0.99 for CD4 T cell count and percentage, respectively. CyFlow MiniPOC showed an excellent repeatability: CD4+ cell count and percentage were analyzed on two instruments, with an intra-assay precision below ± 5% deviation. Finally, there was no carry-over contamination for samples at all CD4 values, regardless of their position in the sequence of analysis.The cost-effective CyFlow MiniPOC produces rapid, reliable and accurate results that are fully comparable with those from highly expensive dual platform systems.

  13. Validation of a single-platform, volumetric, CD45-assisted PanLeucogating Auto40 flow cytometer to determine the absolute number and percentages of CD4 T cells in resource-constrained settings using Cameroonian patients' samples.

    Science.gov (United States)

    Mbopi-Kéou, François-Xavier; Mion, Stefano; Sagnia, Bertrand; Bélec, Laurent

    2012-04-01

    The study evaluated the single-platform, volumetric, CD45-assisted PanLeucogating Auto40 flow cytometer (Apogee Flow Systems Ltd., Hemel Hempstead, United Kingdom) for CD4 T cell numeration, compared to the reference FACSCalibur flow cytometer. Results of absolute counts and percentages of CD4 T cells by Auto40 and FACSCalibur of 234 tripotassium EDTA (K3-EDTA)-blood samples from 146 adults and 88 children (aged from 18 months to 5 years), living in Yaoundé, Cameroon, were highly correlated (r(2) = 0.97 and r(2) = 0.98, respectively). The mean absolute bias and relative bias between Apogee Auto40 and FACSCalibur absolute CD4 T cell counts were +9.6 cells/μl, with limits of agreement from -251 to 270 cells/μl, and +4.1%, with limits of agreement from -16.1 to 24.4%, respectively. The mean absolute bias and relative bias between Apogee Auto40 and FACSCalibur CD4 T cell results expressed as percentages were +0.05% CD4 (95% confidence interval [CI], -0.03 to 0.41), with limits of agreement from -6.0 to 5.9% CD4, and +1.0%, with limits of agreement from -32.3 to 34.4%, respectively. The Auto40 counting allowed identification of the majority of adults with CD4 T cell counts below 200 cells/μl (sensitivity, 87%; specificity, 98%) or below 350 cells/μl (sensitivity, 92%; specificity, 98%) and of children with CD4 T cell counts below 750 cells/μl (sensitivity, 82%; specificity, 98%) or below 25% CD4(+) (sensitivity, 96%; specificity, 99%). The Auto40 analyzer is a reliable alternative flow cytometer for CD4 T lymphocyte enumeration to be used in routine immunological monitoring according to the WHO recommendations for HIV-infected adults as well as children living in resource-constrained settings.

  14. Simultaneous N, C, S isotopic analyses using purge and trap EA technology. Application to δ34S analyses of natural phosphate material NBS120c and BCR32

    Science.gov (United States)

    Fourel, F. P.; Lecuyer, C.; Martineau, F.

    2013-12-01

    The first example of stable isotope analyses in continuous flow mode by Preston et al in 19861 involved Elemental Analyser Isotopic Ratio Mass Spectrometry (EA-IRMS) dedicated to carbon isotopes in combustion mode. EA-IRMS has since then evolved to allow 34S/32S determinations still in combustion mode and mainly to access pyrolysis reaction for O and H isotopes. As far as combustion EA-IRMS is concerned the technique itself has remained unchanged since the development of 'purge and trap' separation techniques online with IRMS instruments. Here we have used a high-precision, easy, low-cost and rapid method of simultaneous carbon, nitrogen and sulphur isotope analysis using this new type of elemental analyser based on 'purge and trap' technology 2,3. Simultaneous determinations, performed on the same aliquot of 13C, 15N and 34S are demonstrated. Emphasis is put on the high quality of 34S/32S determinations. First concentrating on peak shapes, yields of conversion and preliminary results. Then the reliability and accuracy of such a technique is illustrated using analyses from various international reference materials. Alongside international reference material working NCS calibrated material has been selected and characterized prior to apply this technology to calibrate natural phosphate material used as compositional reference material BCR32 and NBS120c. δ34S values of respectively 15.62×0.32‰ and 16.5×0.17‰ are proposed for those samples with sulphur concentrations below the 1% level. The possibility to reliably measure S isotopes on that kind of samples opens up new fields of investigation especially for paleoenvironmental reconstructions. Keywords: carbon, nitrogen, sulfur, isotope, combustion, phosphate, elemental-analyser 1. T. Preston, N.J.P. Owens: Preliminary 13C Measurements using a Gas Chromatograph Interfaced to an Isotope Ratio Mass Spectrometer. Biomedical. Mass Spectrom. 1985, 12-9, 510. 2. H.P. Sieper, H.J. Kupka, L. Lange, A. Rossmann, N. Tanz

  15. Benefits of purging a 200-mm SMIF pod with Nitrogen between wafer processing steps%在圆片加工工序之间充氮清洗200mmSMIF槽的好处

    Institute of Scientific and Technical Information of China (English)

    ChristopherWiebe; SammerA.Abu-Zaid; P.E.; HaifengZhang

    2003-01-01

    For the first part of this paper, several nitrogen(N2) purge experiments have been performed on a200-mm SMIF Pod full of bare silicon wafers. Vari-ous N2 inlet flow rates are used to understand thechanges in oxygen (O2) and moisture (H2O) concen-trations with time. As expected, it is found that asthe N2 flow rate increases, the O2 and moisture con-centrations inside the Pod decrease. Initially, thereduction in O2 and moisture concentrations is veryrapid (convection dominated), and slows down atlower concentrations and becomes diffusiondominated. The leak back rate of O2 and moistureinto the Pod was also analyzed by measuring O2 andmoisture concentrations without N2 flow into thepod, and with a trickle charge (very slow flow) ofN2. It was noticed that the leak back rates of O2 andmoisture is fast during the initial stages of retention,and slows down when the O2 and moisture concen-trations reach higher levels. With trickle charge of N2, it is found that the O2 and moisture concentra-tions inside the Pod can be maintained at very lowlevels for a long time.In the second part of the paper, the effects of N2 purge on limiting the growth of native oxides are explored. The particular application of extending the allowable HF Poly deglaze to Tungsten Silicide depo-sition queue time is analyzed. Extension of the allowable queue time provides two benefits. First, utilization of upstream wafer HF cleaning equipment is improved due to reduced dependence on an idle downstream deposition chamber. Second, HF re- cleaning is eliminated. Increased exposure during HF re-cleaning results in residues at the Polysilicon to Tungsten Silicide interface which later cause blocked etch (reduced yield). It is concluded that as a result of the N2 purge, the queue time between HF deglaze and DCS deposition can be increased without any negative impact resulting from native oxide growth.

  16. Numerical Research on Flow Characteristic of Cooling System for CEFR Fixed Shielding Platform%CEFR堆顶固定屏蔽冷却系统流动特性数值研究

    Institute of Scientific and Technical Information of China (English)

    马晓; 张东辉

    2015-01-01

    堆顶固定屏蔽在中国实验快堆(CEFR)中承担着重要功能,对其进行充分冷却极其重要。本文采用C FD方法对该设备的冷却系统进行了三维数值研究,详细分析了该冷却系统的流动特性和水力学设计,并对设计中的不足提出了优化建议。研究表明,该冷却系统基本可满足要求,但部分环节需要优化。将调节阀尽量均匀布置可改善水平风道流场分布;入口处设置两道通风孔可提高竖直风道内空气流动的均匀性;调节阀开度应适当增加以进一步满足流量分配需求。该研究可为CEFR运行安全和类似冷却系统的设计提供参考。%T he fixed shielding platform plays important function in China Experimental Fast Reactor (CEFR) ,and it’s extremely important to sufficiently cool it .In this paper ,CFD method was used to perform three‐dimensional numerical research on the cooling system for fixed shielding platform .Flow characteristic and hydraulic design of the cooling system were analyzed detailedly .The optimization suggestions were put for‐ward on the defects in the design .The results show that the cooling system can basical‐ly meet the requirements ,but some parts need to be optimized .Flow field distribution in horizontal channels will be improved with more uniformly distributed regulating valves .The uniformity of airflow in vertical channels can be improved with two sets of throttles at inlets .The openness of regulating valves should be properly increased to further meet the requirements of flow distribution .This work can provide reference for operation safety of CEFR and design of similar cooling systems in the future .

  17. Design and Implementation of Intelligent Automatic Purging Control System for All-electric Injection Molding Machine%全电动注塑机智能自动清洗系统控制方法的设计与实现

    Institute of Scientific and Technical Information of China (English)

    于盛睿; 崔树标; 周华民; 李荣荣; 高煌

    2012-01-01

    The manual style had a very negative impact on the plasticization apparatus and precision of injection, so this paper aimed to propose an intelligent automatic purging system and control method for all-electric injection molding machine in order to protect the key plasticization component-screw, which was assembled in the barrel of injection molding machine. The structure, operating principle and program diagram about this control system were introduced. The determinant conditions of entering the automatic purging process were established. Using the determinant conditions, the system can determine intelligently whether the barrel of injection molding machine was needed to be purged or not. A process parameters database of automatic purging was established according to the type of plastic material. The control system was constructed in Linux operating system and Huazhong CNC system platform HNC-8. In each experiment, the PP material of weight of 150 g totally was used to test. The result showed that the automatic purging efficiency was more than the manual's by 33. 7% , and the weight percent of purged remnant material by automatic purging was less than the manual's by 1.84%. Therefore, the efficiency of the designed automatic purge system was superior to the manual. The proposed method can assure the screw's injection precision and performance of the machine, and finally improve the molded part quality and precision.%针对注塑生产过程中手动清洗料筒对注塑精度和塑化装置的影响,为了保护重要塑化元件,在原有注射装置不改变的前提下,提出对料筒中螺杆进行智能自动清洗功能的控制方案,构建智能自动清洗控制系统,阐述了自动清洗系统控制部分的组成、运动原理及工作过程.建立进入自动清洗程序模块的判定条件,对需要进行自动清洗料筒的工况进行智能判断,根据清洗对象建立清洗工艺数据库,基于Linux环境与华中数控HNC-8数控开发平

  18. Product Platform Performance

    DEFF Research Database (Denmark)

    Munk, Lone

    engaging in platform-based product development. Similarly platform assessment criteria lack empirical verification regarding relevance and sufficiency. The thesis focuses on • the process of identifying and estimating internal effects, • verification of performance of product platforms, (i...... to support this understanding. Finally a categorisation of different approaches to platform-based product development is introduced, based on the companies from the industrial study.......The aim of this research is to improve understanding of platform-based product development by studying platform performance in relation to internal effects in companies. Platform-based product development makes it possible to deliver product variety and at the same time reduce the needed resources...

  19. Analytical comparison and sensory representativity of SAFE, SPME, and Purge and Trap extracts of volatile compounds from pea flour.

    Science.gov (United States)

    Murat, Chloe; Gourrat, Karine; Jerosch, Heike; Cayot, Nathalie

    2012-12-01

    Pisum sativum is of great economic and nutritional interest due to its protein content. Nevertheless, pea products are underused as a protein source in human food because of their strong beany flavour. Therefore, the objective of this study was to select an efficient and representative method to extract volatile molecules of pea flour. In the first step, three extraction methods were chosen: solid phase micro extraction (SPME); Purge and Trap extraction and solvent assisted flavour evaporation (SAFE). The corresponding extracts were analysed by gas chromatography coupled with mass spectrometry. In the second step, the sensory representativity of the extracts was assessed either by direct gas chromatography-olfactometry for SPME and for Purge and Trap extracts, or by sniffing for the aqueous SAFE extract. It appeared that SAFE extraction was the most suitable method because of its good extraction capacities and its high sensory representativity of the global odour of pea flour.

  20. Spray chilling of deer carcasses--effects on carcass weight, meat moisture content, purge and microbiological quality.

    Science.gov (United States)

    Wiklund, E; Kemp, R M; leRoux, G J; Li, Y; Wu, G

    2010-12-01

    Twenty red deer carcasses were included in the study. Two treatments were applied to the carcasses; control (air chilling) and spray chilling (n=10 for each treatment). Carcass weight and temperature change were registered during over-night chilling. Meat moisture content was measured in the shoulder, loin, flap and leg before and after the chilling treatments; purge, cooking loss and tenderness were measured in loin samples stored at -1.5 °C for 3 and 9 weeks. Microbiological status was assessed on swabs taken at the lumbar end of the loin before and after the chilling treatments. Spray chilling reduced carcass weight loss significantly; air chilled and spray chilled carcasses lost 1 kg and less than 0.01 kg, respectively. No effects of spray chilling on tenderness, purge and cooking loss were found. Bacterial levels were low in general even after 9 weeks of vacuum packaged chilled storage.

  1. Study on purge gas generated in coke oven gas boilers mixing-firing process%焦炉气锅炉掺烧弛放气探讨

    Institute of Scientific and Technical Information of China (English)

    高翔

    2012-01-01

    It' s not an environmental friendly and economy way to discharged purge gas from methanol plant into the atmosphere. How to recycle methanol purge gas? The treatment of purge gas had been a general concern problem. The problem could be solved by incorpo- rating the decompression purge gas into boilers burning coke oven gas used as burning gas.%甲醇厂弛放气直接排人大气,既对环境产生污染,又无法实现经济价值。通过将弛放气减压掺入焦炉煤气中供锅炉燃烧使用的方法,可以解决弛放气的去向问题。

  2. Reduction of heat-induced haemotoxicity in a hyperthermic purging protocol of murine acute myeloid leukaemic stem cells by AcSDKP

    NARCIS (Netherlands)

    Wierenga, PK; Dillingh, JH; Konings, AWT

    1997-01-01

    The tetrapeptide AcSDKP (Goralatide) is a cytokine with known inhibitory effects on cell proliferation, Many purging agents used in autologous bone marrow transplantation protocols, including hyperthermia, preferentially kill cycling cells. A pretreatment with Goralatide offers a possibility to

  3. Unintended purge during the start-up process of a syringe pump: report of a case presented with vascular collapse.

    Science.gov (United States)

    Farbood, Arash; Kazemi, Asif Parviz; Akbari, Kamal

    2010-12-01

    The case of a 50 year-old woman who developed a sudden decrease in arterial pressure while she was being prepared for surgery for a fractured lumbar spine in the prone position, is reported. She was receiving propofol, remifentanil, and sodium nitroprusside via three syringe pumps through an intravenous cannula at the dorsum of her left hand. The cause of the vascular collapse was the purge of the syringe pumps during the self-check process.

  4. Prevalence of and Familial Influences on Purging Disorder in a Community Sample of Female Twins

    Science.gov (United States)

    Munn-Chernoff, Melissa A.; Keel, Pamela K.; Klump, Kelly L.; Grant, Julia D.; Bucholz, Kathleen K.; Madden, Pamela A. F.; Heath, Andrew C.; Duncan, Alexis E.

    2014-01-01

    Objective Purging Disorder (PD) was recently included as an Otherwise Specified Feeding or Eating Disorder (OSFED) in the DSM-5; however, limited information is available on its prevalence, and its etiology is unknown. Method Data from 1790 monozygotic and 1440 dizygotic European American female twins (age range = 18 – 29 years) from the Missouri Adolescent Female Twin Study were used to investigate prevalence and familial influences for PD. A structured clinical interview assessed lifetime DSM-IV criteria for eating disorders and PD. After adjustment for age, twin correlations and biometrical twin models were used to estimate familial (i.e., genetic plus shared environmental) influences on PD. Results One hundred and twenty one (3.77%; 95% CI: 3.14, 4.49) women met criteria for lifetime PD. Twin correlations suggested that genetic, shared environmental, and nonshared environmental factors influenced liability to PD. Nonshared environmental factors accounted for 56% [35%, 79%] of the variance in PD. Although familial effects accounted for a significant proportion of variance (44% [21%, 65%]), it was not possible to disentangle the independent contributions of additive genetic effects (20% [0%, 65%]) and shared environmental effects (24% [0%, 57%]). Discussion PD is a prevalent form of eating pathology. Familial factors are relevant to the development of PD but do not demonstrate the magnitude of heritable factors found for other eating disorders. PMID:25808399

  5. Effect of self-purging pyrolysis on yield of biochar from maize cobs, husks and leaves.

    Science.gov (United States)

    Intani, Kiatkamjon; Latif, Sajid; Kabir, A K M Rafayatul; Müller, Joachim

    2016-10-01

    In this study, biochar was produced from maize residues (cobs, husks, leaves) in a lab-scale pyrolysis reactor without using a purging gas. The physicochemical properties of biomass and biochar were analysed. Box-Behnken design was used to optimise operational conditions for biochar yields. Multivariate correlations of biochar yields were established using reduced quadratic models with R(2)=0.9949, 0.9801 and 0.9876 for cobs, husks and leaves, respectively. Biochar yields were negatively correlated with the temperature, which was significantly influenced by the exothermic reactions during the pyrolysis of maize residues. The heating rate was found to have the least effect on biochar yields. Under optimal conditions, the maximum biochar yields from cobs, husks and leaves were 33.42, 30.69 and 37.91%, respectively. The highest biochar yield from maize leaves was obtained at a temperature of 300°C, a heating rate of 15°C/min and a holding time of 30min.

  6. Oncolytic viral purging of leukemic hematopoietic stem and progenitor cells with Myxoma virus.

    Science.gov (United States)

    Rahman, Masmudur M; Madlambayan, Gerard J; Cogle, Christopher R; McFadden, Grant

    2010-01-01

    High-dose chemotherapy and radiation followed by autologous blood and marrow transplantation (ABMT) has been used for the treatment of certain cancers that are refractory to standard therapeutic regimes. However, a major challenge with ABMT for patients with hematologic malignancies is disease relapse, mainly due to either contamination with cancerous hematopoietic stem and progenitor cells (HSPCs) within the autograft or the persistence of residual therapy-resistant disease niches within the patient. Oncolytic viruses represent a promising therapeutic approach to prevent cancer relapse by eliminating tumor-initiating cells that contaminate the autograft. Here we summarize an ex vivo "purging" strategy with oncolytic Myxoma virus (MYXV) to remove cancer-initiating cells from patient autografts prior to transplantation. MYXV, a novel oncolytic poxvirus with potent anti-cancer properties in a variety of in vivo tumor models, can specifically eliminate cancerous stem and progenitor cells from samples obtained from acute myelogenous leukemia (AML) patients, while sparing normal CD34+ hematopoietic stem and progenitor cells capable of rescuing hematopoiesis following high dose conditioning. We propose that a broader subset of patients with intractable hematologic malignancies who have failed standard therapy could become eligible for ABMT when the treatment schema is coupled with ex vivo oncolytic therapy.

  7. Desalination of simulated seawater by purge-air pervaporation using an innovative fabricated membrane.

    Science.gov (United States)

    Naim, Mona; Elewa, Mahmoud; El-Shafei, Ahmed; Moneer, Abeer

    2015-01-01

    An innovative polymeric membrane has been invented, which presents a breakthrough in the field of desalination membranes. It can desalinate simulated seawater of exceptionally high concentration to produce a high flux of potable water with over 99.7% salt rejection (%SR) in a once-through purge-air pervaporation (PV) process. A set-up was constructed for conducting the desalination experiments and the effect of initial salt solution concentration (Ci) and pervaporation temperature (Tpv) on the water flux (J), %SR, separation factor, and pervaporation separation index were determined. The membrane was prepared by the phase-inversion technique, of a specially formulated casting solution consisting of five ingredients, after which the membrane was subjected to a post-treatment by which certain properties were conferred. The results confirmed that the salinity of the pervaporate was independent of Ci (all %SR above 99.7). The best result was at Tpv=70 °C, where J varied from 5.97 to 3.45 l/m2 h for Ci=40-140 g NaCl/l, respectively. The membrane morphology was confirmed to be asymmetric. The contact angle was immeasurable, indicating the membrane to be super-hydrophilic. Activation energies computed using Arrhenius law were, under all conditions investigated, less than 20 kJ/mol K.

  8. Adaptation to a new environment allows cooperators to purge cheaters stochastically.

    Science.gov (United States)

    Waite, Adam James; Shou, Wenying

    2012-11-20

    Cooperation via production of common goods is found in diverse life forms ranging from viruses to social animals. However, natural selection predicts a "tragedy of the commons": Cheaters, benefiting from without producing costly common goods, are more fit than cooperators and should destroy cooperation. In an attempt to discover novel mechanisms of cheater control, we eliminated known ones using a yeast cooperator-cheater system engineered to supply or exploit essential nutrients. Surprisingly, although less fit than cheaters, cooperators quickly dominated a fraction of cocultures. Cooperators isolated from these cocultures were superior to the cheater isolates they had been cocultured with, even though these cheaters were superior to ancestral cooperators. Resequencing and phenotypic analyses revealed that evolved cooperators and cheaters all harbored mutations adaptive to the nutrient-limited cooperative environment, allowing growth at a much lower concentration of nutrient than their ancestors. Even after the initial round of adaptation, evolved cooperators still stochastically dominated cheaters derived from them. We propose the "adaptive race" model: If during adaptation to an environment, the fitness gain of cooperators exceeds that of cheaters by at least the fitness cost of cooperation, the tragedy of the commons can be averted. Although cooperators and cheaters sample from the same pool of adaptive mutations, this symmetry is soon broken: The best cooperators purge cheaters and continue to grow, whereas the best cheaters cause rapid self-extinction. We speculate that adaptation to changing environments may contribute to the persistence of cooperative systems before the appearance of more sophisticated mechanisms of cheater control.

  9. Analysis of ammonia separation from purge gases in microporous hollow fiber membrane contactors.

    Science.gov (United States)

    Karami, M R; Keshavarz, P; Khorram, M; Mehdipour, M

    2013-09-15

    In this study, a mathematical model was developed to analyze the separation of ammonia from the purge gas of ammonia plants using microporous hollow fiber membrane contactors. A numerical procedure was proposed to solve the simultaneous linear and non linear partial differential equations in the liquid, membrane and gas phases for non-wetted or partially wetted conditions. An equation of state was applied in the model instead of Henry's law because of high solubility of ammonia in water. The experimental data of CO₂-water system in the literature was used to validate the model due to the lack of data for ammonia-water system. The model showed that the membrane contactor can separate ammonia very effectively and with recoveries higher than 99%. SEM images demonstrated that ammonia caused some micro-cracks on the surfaces of polypropylene fibers, which could be an indication of partial wetting of membrane in long term applications. However, the model results revealed that the membrane wetting did not have significant effect on the absorption of ammonia because of very high solubility of ammonia in water. It was also found that the effect of gas velocity on the absorption flux was much more than the effect of liquid velocity.

  10. Identification of New Rat Bone Marrow-Derived Population of Very Small Stem Cell with Oct-4A and Nanog Expression by Flow Cytometric Platforms

    Directory of Open Access Journals (Sweden)

    Anna Labedz-Maslowska

    2016-01-01

    Full Text Available Very small embryonic-like stem cells (VSELs represent a unique rare population of adult stem cells (SCs sharing several structural, genetic, biochemical, and functional properties with embryonic SCs and have been identified in several adult murine and human tissues. However, rat bone marrow- (BM- derived SCs closely resembling murine or human VSELs have not been described. Thus, we employed multi-instrumental flow cytometric approach including classical and imaging cytometry and we established that newly identified population of nonhematopoietic cells expressing CD106 (VCAM-I antigen contains SCs with very small size, expressing markers of pluripotency (Oct-4A and Nanog on both mRNA and protein levels that indicate VSEL population. Based on our experience in both murine and human VSEL isolation procedures by fluorescence-activated cell sorting (FACS, we also optimized sorting protocol for separation of CD45−/Lin−/CD106+ rat BM-derived VSELs from wild type and eGFP-expressing rats, which are often used as donor animals for cell transplantations in regenerative studies in vivo. Thus, this is a first study identifying multiantigenic phenotype and providing sorting protocols for isolation VSELs from rat BM tissue for further examining of their functional properties in vitro as well as regenerative capacity in distinct in vivo rat models of tissue injury.

  11. Thermal Spray Using a High-Frequency Pulse Detonation Combustor Operated in the Liquid-Purge Mode

    Science.gov (United States)

    Endo, T.; Obayashi, R.; Tajiri, T.; Kimura, K.; Morohashi, Y.; Johzaki, T.; Matsuoka, K.; Hanafusa, T.; Mizunari, S.

    2016-02-01

    Experiments on thermal spray by pulsed detonations at 150 Hz were conducted. Two types of pulse detonation combustors were used, one operated in the inert gas purge (GAP) mode and the other in the liquid-purge (LIP) mode. In both modes, all gases were supplied in the valveless mode. The GAP mode is free of moving components, although the explosive mixture is unavoidably diluted with the inert gas used for the purge of the hot burned gas. In the LIP mode, pure fuel-oxygen combustion can be realized, although a liquid-droplet injector must be actuated cyclically. The objective of this work was to demonstrate a higher spraying temperature in the LIP mode. First, the temperature of CoNiCrAlY particles heated by pulsed detonations was measured. As a result, the spraying temperature in the LIP mode was higher than that in the GAP mode by about 1000 K. Second, the temperature of yttria-stabilized zirconia (YSZ) particles, whose melting point was almost 2800 °C, heated by pulsed detonations in the LIP mode was measured. As a result, the YSZ particles were heated up to about 2500 °C. Finally, a thermal spray experiment using YSZ particles was conducted, and a coating with low porosity was successfully deposited.

  12. Needle-type extraction device for the purge and trap analysis of 23 volatile organic compounds in tap water.

    Science.gov (United States)

    Ueta, Ikuo; Razak, Nurhafizza Abd; Mizuguchi, Ayako; Kawakubo, Susumu; Saito, Yoshihiro; Jinno, Kiyokatsu

    2013-11-22

    We developed a rapid determination technique for trace volatile organic compounds (VOCs) in tap water by introducing a novel needle-type extraction device coupled to a purge-and-trap method. To extract a wide range of VOCs, a new extraction needle containing particles of divinylbenzene and activated carbon was developed in this study. During the active sampling of the headspace gas in a glass vial by the extraction needle, pure N2 gas was used for purging the aqueous sample. After the optimization of several experimental parameters, such as the addition of the salt and conditions of dry purging and desorption, the extraction performance of the device and method was evaluated for 23 VOCs that are typically found in tap water samples. The quantification limits of the method were 0.6 μg/L for 1,1-dichloroethylene and less than 0.5 μg/L for other VOCs, with good repeatability being confirmed for all the target compounds. Taking advantage of the excellent recovery of VOCs, the determination of VOCs in real tap water samples was carried out successfully. Because the developed method does not require sample heating and/or cryogenic focusing, simple and rapid analyses can be performed along with satisfactory sensitivity for typical tap water samples.

  13. Temporal change in inbreeding depression in life-history traits in captive populations of guppy (Poecilia reticulata): evidence for purging?

    Science.gov (United States)

    Larsen, L-K; Pélabon, C; Bolstad, G H; Viken, A; Fleming, I A; Rosenqvist, G

    2011-04-01

    Inbreeding depression, which generally affects the fitness of small populations, may be diminished by purging recessive deleterious alleles when inbreeding persists over several generations. Evidence of purging remains rare, especially because of the difficulties of separating the effects of various factors affecting fitness in small populations. We compared the expression of life-history traits in inbred populations of guppy (Poecilia reticulata) with contemporary control populations over 10 generations in captivity. We estimated inbreeding depression as the difference between the two types of populations at each generation. After 10 generations, the inbreeding coefficient reached a maximum value of 0.56 and 0.16 in the inbred and control populations, respectively. Analysing changes in the life-history traits across generations showed that inbreeding depression in clutch size and offspring survival increased during the first four to six generations in the populations from the inbred treatment and subsequently decreased as expected if purging occurred. Inbreeding depression in two other traits was weaker but showed similar changes across generations. The loss of six populations in the inbred treatment indicates that removal of deleterious alleles also occurred by extinction of populations that presumably harboured high genetic load.

  14. Reciprocal associations between negative affect, binge eating, and purging in the natural environment in women with bulimia nervosa.

    Science.gov (United States)

    Lavender, Jason M; Utzinger, Linsey M; Cao, Li; Wonderlich, Stephen A; Engel, Scott G; Mitchell, James E; Crosby, Ross D

    2016-04-01

    Although negative affect (NA) has been identified as a common trigger for bulimic behaviors, findings regarding NA following such behaviors have been mixed. This study examined reciprocal associations between NA and bulimic behaviors using real-time, naturalistic data. Participants were 133 women with bulimia nervosa (BN) according to the 4th edition of the Diagnostic and Statistical Manual of Mental Disorders who completed a 2-week ecological momentary assessment protocol in which they recorded bulimic behaviors and provided multiple daily ratings of NA. A multilevel autoregressive cross-lagged analysis was conducted to examine concurrent, first-order autoregressive, and prospective associations between NA, binge eating, and purging across the day. Results revealed positive concurrent associations between all variables across all time points, as well as numerous autoregressive associations. For prospective associations, higher NA predicted subsequent bulimic symptoms at multiple time points; conversely, binge eating predicted lower NA at multiple time points, and purging predicted higher NA at 1 time point. Several autoregressive and prospective associations were also found between binge eating and purging. This study used a novel approach to examine NA in relation to bulimic symptoms, contributing to the existing literature by directly examining the magnitude of the associations, examining differences in the associations across the day, and controlling for other associations in testing each effect in the model. These findings may have relevance for understanding the etiology and/or maintenance of bulimic symptoms, as well as potentially informing psychological interventions for BN. (c) 2016 APA, all rights reserved).

  15. SUBMERGED GRAVEL SCRUBBER DEMONSTRATION AS A PASSIVE AIR CLEANER FOR CONTAINMENT VENTING AND PURGING WITH SODIUM AEROSOLS -- CSTF TESTS AC7 - AC10

    Energy Technology Data Exchange (ETDEWEB)

    HILLIARD, R K.; MCCORMACK, J D.; POSTMA, A K.

    1981-11-01

    Four large-scale air cleaning tests (AC7 - AC10) were performed in the Containment Systems Test Facility (CS'lF) to demonstrate the performance of a Submerged Gravel Scrubber for cleaning the effluent gas from a vented and purged breeder reactor containment vessel. The test article, comprised of a Submerged Gravel Scrubber (SGS) followed by a high efficiency fiber demister, had a design gas flow rate of 0.47 m{sup 3}/s (1000 ft{sup 3}/min) at a pressure drop of 9.0 kPa (36 in. H{sub 2}O). The test aerosol was sodium oxide, sodium hydroxide, or sodium carbonate generated in the 850-m{sup 3} CSTF vessel by continuously spraying sodium into the air-filled vessel while adding steam or carbon dioxide. Approximately 4500 kg (10,000 lb) of sodium was sprayed over a total period of 100 h during the tests. The SGS/Demister system was shown to be highly efficient (removing ~99.98% of the entering sodium aerosol mass), had a high mass loading capacity, and operated in a passive manner, with no electrical requirement. Models for predicting aerosol capture, gas cooling, and pressure drop are developed and compared with experimental results.

  16. Regulation of purine biosynthetic genes expression in Salmonella typhimurium Ⅳ O~c mutation site of purG and its function analysis

    Institute of Scientific and Technical Information of China (English)

    刘奔; 黄谊; 王敖全

    1997-01-01

    Salmonella typhimurium 5 phosphoribosylformylglycinamide (FGAR) amidotransferase encoded by purG gene catalyzes the conversion of FGAR to formylglycinamide ribonucleotide (FGAM) in the presence of glu-tamine and ATP for the de novo purine nucleotide biosynthesis. purG gene is negatively regulated by a repressor-oper-ator system. The O+ purG and OC purG were cloned respectively in vivo. Restriction enzymes analysis of preliminary clones pLBG-1 (O + ) and pLBG-2 (OC) were carried out. The hybrid plasmids pLB1933 (O+ ) and pLB1927 (OC) containing 5 control region of purG were constructed and the DNA sequences were determined respectively. DNA se-quences data showed that Oc mutation of purG occurred at the 3rd position of 16 bp PUR box in the 5’ control region ( G→A). Gel retardation experiment indicated that the repressor bound well with O+ PUR box, but not with Oc PUR box. The result strongly supported the idea that PUR box is the binding region of represser protein and the 3rd posi-tion base G of PUR bo

  17. Product Platform Modeling

    DEFF Research Database (Denmark)

    Pedersen, Rasmus

    on the notion that reuse and encapsulation of platform elements are fundamental characteristics of a product platform. Reuse covers the desire to reuse and share certain assets across a family of products and/or across generations of products. Product design solutions and principles are often regarded...... as important assets in a product platform, yet activities, working patterns, processes and knowledge can also be reused in a platform approach. Encapsulation is seen as a process in which the different elements of a platform are grouped into well defined and self-contained units which are decoupled from each......This PhD thesis has the title Product Platform Modelling. The thesis is about product platforms and visual product platform modelling. Product platforms have gained an increasing attention in industry and academia in the past decade. The reasons are many, yet the increasing globalisation...

  18. AUV协同设计平台中多任务流调度算法研究%Research on multiple task flows scheduling algorithm in collaborative design platform for AUV

    Institute of Scientific and Technical Information of China (English)

    XU Zhen-zhen; ZHAO Xiao-wei; XU Xiu-juan; HU Zhi-qiang; CHEN Xin

    2014-01-01

    对AUV协同设计平台中多个任务流的调度问题进行建模,将其转换为分布式计算环境下的独立任务在线调度问题。针对系统异构和任务流具有优先级属性的特殊性,提出了一种基于预测的多任务流调度算法,采用统计和预测的方法评估各工作站执行任务的效用,并设计优先级策略和暂停调度策略,保证具有较高优先级的任务流较早分配和执行。实验结果表明,该算法在参数选取适当的情况下,性能优于传统的MCT和MET任务调度算法。%This paper modeled the multiple task flows scheduling problem in the collaborative design platform for AUV and transformed it into the independent tasks online scheduling problem in the distributed computing environment.Aiming at the particularity includi

  19. Adaptation to a new environment allows cooperators to purge cheaters stochastically

    Science.gov (United States)

    Waite, Adam James; Shou, Wenying

    2012-01-01

    Cooperation via production of common goods is found in diverse life forms ranging from viruses to social animals. However, natural selection predicts a “tragedy of the commons”: Cheaters, benefiting from without producing costly common goods, are more fit than cooperators and should destroy cooperation. In an attempt to discover novel mechanisms of cheater control, we eliminated known ones using a yeast cooperator–cheater system engineered to supply or exploit essential nutrients. Surprisingly, although less fit than cheaters, cooperators quickly dominated a fraction of cocultures. Cooperators isolated from these cocultures were superior to the cheater isolates they had been cocultured with, even though these cheaters were superior to ancestral cooperators. Resequencing and phenotypic analyses revealed that evolved cooperators and cheaters all harbored mutations adaptive to the nutrient-limited cooperative environment, allowing growth at a much lower concentration of nutrient than their ancestors. Even after the initial round of adaptation, evolved cooperators still stochastically dominated cheaters derived from them. We propose the “adaptive race” model: If during adaptation to an environment, the fitness gain of cooperators exceeds that of cheaters by at least the fitness cost of cooperation, the tragedy of the commons can be averted. Although cooperators and cheaters sample from the same pool of adaptive mutations, this symmetry is soon broken: The best cooperators purge cheaters and continue to grow, whereas the best cheaters cause rapid self-extinction. We speculate that adaptation to changing environments may contribute to the persistence of cooperative systems before the appearance of more sophisticated mechanisms of cheater control. PMID:23091010

  20. Group cognitive behavioral treatment in female soldiers diagnosed with binge/purge eating disorders.

    Science.gov (United States)

    Carter, Rinat; Yanykulovitch-Levy, Dana; Wertheim, Hadas; Gordon-Erez, Shirley; Shahimov, Meital; Weizman, Abraham; Stein, Daniel

    2016-01-01

    Cognitive behavioral treatment (CBT) is the recommended intervention in bulimia nervosa (BN) and eating disorders not otherwise specified with binge/purge (EDNOS-B/P) symptoms. There are fewer data on its application in a group format. We sought to investigate the effect of group CBT in female soldiers with B/P symptomatology in an open trial design. For this purpose we assessed 64 female soldiers serving in the Israeli Defense Force diagnosed with BN and EDNOS-B/P who participated in a group CBT format of 16 weekly sessions and one follow-up session. In this study, 42 participants (65.6%) completed treatment and 22 participants (34.4%) did not. A total of 39 treatment completers (92.8% of treatment completers) and 19 non-completers (86.4% of treatment non-completers) were assessed around 12 months after treatment. Participants completed at baseline and following treatment questionnaires assessing eating-related symptoms, depression, anxiety, and overall functioning. At follow-up they were assessed for eating-related symptoms. Our findings show only minimal baseline differences between treatment completers and non-completers. Significant improvement from baseline to post-treatment was shown for B/P and restrictive symptoms, depression, anxiety, and overall functioning. At that time, more than a third of treatment completers were abstinent from binging and more than a half from vomiting. The improvement in B/P and restricting symptoms was maintained at 1 year follow-up for treatment completers. At that time around 60% were abstinent from binging and more than 70% from vomiting. Participants not completing treatment were also improved at follow-up but to a lesser extent. The findings of the present study suggest that group CBT may be effective for the treatment of female soldiers with BN and EDNOS-B/P.

  1. Purge lecithin for less-expensive diet formulation for black tiger prawn Penaeus monodon

    Directory of Open Access Journals (Sweden)

    Shanmugam Velmurugan

    2010-12-01

    Full Text Available The knowledge of the nutrient requirements and practical diet formulations for Penaeus monodon is fully known. In the production cost, the cost of diet alone comes around 50 to70%. This ismainly because of the addition of lecithin which is a relatively expensive dietary ingredient. It isimportant to determine the usefulness of lecithin in the growth of P. monodon. In order to keep the dietcost as low as possible this experiment was designed with and without lecithin. The objective of thepresent study was to assess the growth of shrimp with varying lecithin doses. To study the water qualityparameters and to study the growth and survival of animals feed containing different percentage oflecithin. Trials conducted indicated the soybean lecithin did not have any effect on shrimp’s growth. Theshrimp weight varied from 3.15 to 8g in Control, 2.58 to 6g in Treatment A, 2.87 to 6.62g in TreatmentB, 3.1 to 6.75g in Treatment C. These confirm that under a controlled clear water culture system, partialor complete replacement of soybean lecithin in a commercial diet for P. monodon resulted in nodetriment in growth. Purge lecithin in the diet may allow for less-expensive diet formulations for P.monodon and may reduce the diet cost for producers, who are supplying feed. As diet cost representsthe largest variable cost in a commercial aquaculture operation, increased knowledge of specific dietaryrequirements is essential for formulating a cost-effective commercial P. monodon diet.

  2. Monitoring of phthalates in foodstuffs using gas purge microsyringe extraction coupled with GC-MS.

    Science.gov (United States)

    He, Miao; Yang, Cui; Geng, Renjie; Zhao, Xiangai; Hong, Lian; Piao, Xiangfan; Chen, Tie; Quinto, Maurizio; Li, Donghao

    2015-06-16

    Phthalate esters (PAEs) are commonly used as nonreactive plasticisers in vinyl plastics to increase the flexibility of plastic polymers. Numerous studies have indicated that the PAEs as a class of endocrine-disrupting chemicals. In addition, the studies have also shown that a major source of human exposure to phthalates is the diet. To date, the largest problem in PAEs analysis is the high blank value because PAEs are widely used in various applications and products. To overcome this shortcoming, gas purge microsyringe extraction (GP-MSE) was applied, which established a new and low-blank-value analytical method for PAE analysis to analyse PAEs in foodstuffs. In this study, GP-MSE was used as a clean-up method, and the overall recoveries ranged from 85.7 to 102.6%, and the RSD was less than 10%. More importantly, this method can overcome the problem of the high blank value in PAE analysis. This method was applied for measuring PAEs in 78 foodstuffs. The results showed that a wide variety of PAE concentrations were found in the different groups, and the content of PAEs (varies from 658 to 1610 ng g(-1) fresh weight) is greatest in seafood. The concentrations were in the following order: DEHP>DBP>DEP≈DMP>BBP≈DNOP. Finally, the daily intake of PAEs was estimated for adults based on the levels of PAEs in foodstuffs. The total EDIdiet values of 3.2 and 12.9 μg kg(-1) bw d(-1) were calculated for DEHP based on the mean and highest concentrations in foodstuffs, respectively.

  3. ITS Platform North Denmark

    DEFF Research Database (Denmark)

    Lahrmann, Harry; Agerholm, Niels; Juhl, Jens

    2012-01-01

    This paper presents the project entitled “ITS Platform North Denmark” which is used as a test platform for Intelligent Transportation System (ITS) solutions. The platform consists of a newly developed GNSS/GPRS On Board Unit (OBU) to be installed in 500 cars, a backend server and a specially...... designed digital road map for ITS applications. The platform is freely accessible, which means that third party applications could be run on the platform. It is estimated that using this platform enables the ITS applications to be developed for 20% of the normal cost, hence third party are invited to test...... their applications in this platform. This paper presents the platform’s potentials and explains a series of test applications which are under development on it. Moreover, a number of new projects planned for the platform are demonstrated....

  4. Mobile platform security

    CERN Document Server

    Asokan, N; Dmitrienko, Alexandra

    2013-01-01

    Recently, mobile security has garnered considerable interest in both the research community and industry due to the popularity of smartphones. The current smartphone platforms are open systems that allow application development, also for malicious parties. To protect the mobile device, its user, and other mobile ecosystem stakeholders such as network operators, application execution is controlled by a platform security architecture. This book explores how such mobile platform security architectures work. We present a generic model for mobile platform security architectures: the model illustrat

  5. Continuous Platform Development

    DEFF Research Database (Denmark)

    Nielsen, Ole Fiil

    low risks and investments but also with relatively fuzzy results. When looking for new platform projects, it is important to make sure that the company and market is ready for the introduction of platforms, and to make sure that people from marketing and sales, product development, and downstream......, but continuous product family evolution challenges this strategy. The concept of continuous platform development is based on the fact that platform development should not be a one-time experience but rather an ongoing process of developing new platforms and updating existing ones, so that product family...

  6. Cross-Platform Technologies

    Directory of Open Access Journals (Sweden)

    Maria Cristina ENACHE

    2017-04-01

    Full Text Available Cross-platform - a concept becoming increasingly used in recent years especially in the development of mobile apps, but this consistently over time and in the development of conventional desktop applications. The notion of cross-platform software (multi-platform or platform-independent refers to a software application that can run on more than one operating system or computing architecture. Thus, a cross-platform application can operate independent of software or hardware platform on which it is execute. As a generic definition presents a wide range of meanings for purposes of this paper we individualize this definition as follows: we will reduce the horizon of meaning and we use functionally following definition: a cross-platform application is a software application that can run on more than one operating system (desktop or mobile identical or in a similar way.

  7. Unsteady Aerodynamic Flow Control of Moving Platforms

    Science.gov (United States)

    2014-05-29

    Hsiao et al. 1990, Neuberger and Wygnanski 1987, Williams et al. 1991, Chang et al. 1992, Seifert et al. 1993). An alternative approach uses actuation...34, Mechanics of Materials, Vol. 38, 2006, pp. 463-474. Neuberger D. and Wygnanski I., “The Use of a Vibrating Ribbon to Delay Separation on Two

  8. The Role of Non-Suicidal Self-Injury and Binge-Eating/Purging Behaviours in Family Functioning in Eating Disorders.

    Science.gov (United States)

    Depestele, Lies; Claes, Laurence; Dierckx, Eva; Baetens, Imke; Schoevaerts, Katrien; Lemmens, Gilbert M D

    2015-09-01

    This study aimed to investigate family functioning of restrictive and binge-eating/purging eating disordered adolescents with or without non-suicidal self-injury (NSSI), as perceived by the patients and their parents (mothers and fathers). In total, 123 patients (between 14 and 24 years), 98 mothers and 79 fathers completed the Family Assessment Device. Patients completed the Self-Injury Questionnaire-Treatment Related and the Symptom Checklist 90-Revised. No main effects were found of restrictive versus binge-eating/purging behaviour nor of presence/absence of NSSI. For the parents, a significant interaction between binge-eating/purging behaviour and NSSI emerged: Mothers and fathers reported worse family functioning in the binge-eating/purging group in presence of NSSI, whereas mothers reported worse family functioning in the restrictive group without NSSI. Parental perception of family functioning is affected by the combined presence of binge-eating/purging behaviour and NSSI. This finding should be taken into account when treating families living with eating disorders.

  9. Cardiac Risk and Disordered Eating: Decreased R Wave Amplitude in Women with Bulimia Nervosa and Women with Subclinical Binge/Purge Symptoms.

    Science.gov (United States)

    Green, Melinda; Rogers, Jennifer; Nguyen, Christine; Blasko, Katherine; Martin, Amanda; Hudson, Dominique; Fernandez-Kong, Kristen; Kaza-Amlak, Zauditu; Thimmesch, Brandon; Thorne, Tyler

    2016-11-01

    The purpose of the present study was threefold. First, we examined whether women with bulimia nervosa (n = 12) and women with subthreshold binge/purge symptoms (n = 20) showed decreased mean R wave amplitude, an indicator of cardiac risk, on electrocardiograph compared to asymptomatic women (n = 20). Second, we examined whether this marker was pervasive across experimental paradigms, including before and after sympathetic challenge tasks. Third, we investigated behavioural predictors of this marker, including binge frequency and purge frequency assessed by subtype (dietary restriction, excessive exercise, self-induced vomiting, and laxative abuse). Results of a 3 (ED symptom status) × 5 (experimental condition) mixed factorial ANCOVA (covariates: body mass index, age) indicated women with bulimia nervosa and women with subclinical binge/purge symptoms demonstrated significantly reduced mean R wave amplitude compared to asymptomatic women; this effect was pervasive across experimental conditions. Multiple regression analyses showed binge and purge behaviours, most notably laxative abuse as a purge method, predicted decreased R wave amplitude across all experimental conditions. Copyright © 2016 John Wiley & Sons, Ltd and Eating Disorders Association.

  10. 中韩石化武汉乙烯蒸汽管道吹扫分析%The Analysis of Purging Steam Pipe in SSWPC

    Institute of Scientific and Technical Information of China (English)

    唐旭

    2015-01-01

    The fundamental state of steam pipe network in the plant was introduced. A program for purging steam pipe was formulated with analysis of purging steam pipe theory and parameter estimates. Improvements were suggested to solve steam targeting problems and analyze reasons through the purging. It concluded that purging steam pipe theory and practical operation method were deeply understood, which was useful for similar purging pipe as a reference.%介绍我厂蒸汽管网概况,并对蒸汽吹扫原理和参数测算进行分析,制定吹扫方案。介绍我厂蒸汽管线吹扫的流程和吹扫中的问题和原因分析及解决措施。通过总结分析,加深对蒸汽吹扫理论和实际操作方法的认识,对于同类蒸汽管线吹扫具有参考意义。

  11. Service Situation and Improvement Measures of Purging Plug Brick for Steel Ladle%钢包用透气砖的使用及改进措施

    Institute of Scientific and Technical Information of China (English)

    杨幸福; 崔庆阳; 徐兵; 毛晓刚; 崔广进

    2012-01-01

    The service requirements and damage mechanism of the purging plug brick for steel ladle are analyzed, and the influencing factors for the service life of purging plug brick are analyzed and discussed from the design, the production process, the operating conditions and the smelting conditions. The measures of improving the use of the purging plug brick are put forward, and at the same time the safety of the purging plug brick should be ensured to avoid the abnormal ladle-to-ladle phenomenon, even breakout accident in using. And the development trend of the purging plug brick is discussed.%对钢包用透气砖的使用要求和损毁机理进行了分析,并从透气砖的设计、生产工艺、操作条件、冶炼条件等方面分析讨论了透气砖寿命的影响因素,提出了改善透气砖使用情况的措施,同时提出要保证透气砖的安全性,避免在使用的过程中出现非正常倒包现象,甚至漏钢事故.并对透气砖的发展方向进行了探讨.

  12. 吹扫捕集-气相色谱/质谱法同时测定水中的27种挥发性有机物%Simultaneous Determination of 27 Volatile Organic Compounds in Water by Purge and Trap Coupled with GC-MS

    Institute of Scientific and Technical Information of China (English)

    普学伟; 施艳峰

    2016-01-01

    Volatile organic compounds ( VOCs) in water sample were desorbed after purge and concentration, and then separated u-sing a HP-VOC column in gas chromatography. The MS analysis was done under both full scan mode and selected ion monitoring mode, and the quantification was done using the internal standard calibration. It was determined that the optimum conditions of the purge and concentration were purge flow of 40 mL/min, purge temperature of 40 ℃, purge time of 15 min, desorption temperature of 200 ℃, and desorption time of 2 min. Linear relationships with coefficient values r greater than 0. 995 were obtained between in-dividual peak area and mass concentration of the 27 VOCs within a defined concentration range. Method detection limits were ranged from 0. 02 to 1. 18 μg/L. Blank samples were tested for recovery rate using the standard addition method, and recovery rates were found to be in the range of 79. 8% ~114% with RSDs in the range of 0. 3% ~12%.%水中的VOCs经吹扫富集、解吸后,用HP-VOC色谱柱分离,采用全扫描和选择离子监测模式分析,内标法定量。最佳富集条件为:吹扫流速为40 mL/min,吹扫温度为40℃,吹扫时间为15 min,解吸温度为200℃,解吸时间为2 min。该法27种VOCs在一定的质量浓度范围内与其峰面积呈线性关系,相关系数r >0.995,检出限为0.02~1.18μg/L。以空白样品为基体进行加标回收试验,测得回收率为79.8%~114%,相对标准偏差为0.3%~12%。

  13. Platform switching and bone platform switching.

    Science.gov (United States)

    Carinci, Francesco; Brunelli, Giorgio; Danza, Matteo

    2009-01-01

    Bone platform switching involves an inward bone ring in the coronal part of the implant that is in continuity with the alveolar bone crest. Bone platform switching is obtained by using a dental fixture with a reverse conical neck. A retrospective study was performed to evaluate the effectiveness of conventional vs reverse conical neck implants. In the period between May 2004 and November 2007, 86 patients (55 females and 31 males; median age, 53 years) were operated and 234 implants were inserted: 40 and 194 were conventional vs reverse conical neck implants, respectively. Kaplan-Meier algorithm and Cox regression were used to detect those variables associated with the clinical outcome. No differences in survival and success rates were detected between conventional vs reverse conical neck implants alone or in combination with any of the studied variables. Although bone platform switching leads to several advantages, no statistical difference in alveolar crest resorption is detected in comparison with reverse conical neck implants. We suppose that the proximity of the implant abutment junction to the alveolar crestal bone gives no protection against the microflora contained in the micrograph. Additional studies on larger series and a combination of platform switching and bone platform switching could lead to improved clinical outcomes.

  14. 钢包用透气砖的研究与发展方向%Research and development direction of purging plug for ladle

    Institute of Scientific and Technical Information of China (English)

    常雅楠; 张玲; 邵子铭

    2016-01-01

    The effect of purging plug’s materials and structure on thermal shock resistance and slag resistance was summarized,and the research progress on the use of performance and damage mechanism was reviewed. Then the effect of argon blowing process on the work of purging plug was introduced,and the further research and developing trend of purging were proposed in this paper.%综述了透气砖的材质和结构对其抗热震稳定性和抗渣性的影响,以及透气砖在使用性能和损毁机理方面的研究进展,介绍了吹氩工艺对透气砖工作的影响,提出了钢包用透气砖耐火材料的可能的发展方向。

  15. Comparison of quarter-hourly on-line dynamic headspace analysis to purge-and-trap analysis of varying volatile organic compounds in drinking water sources.

    Science.gov (United States)

    Schnable, J G; Dussert, B; Suffet, I H; Hertz, C D

    1990-07-27

    On-line dynamic headspace analysis was refined for the quarter-hourly monitoring of select volatile organic compounds (VOCs) in ground and surface waters, for extended periods of time. Hourly comparisons were made to on-line purge-and-trap analysis, and to purge-and-trap analysis after sample preservation and storage. Variations in VOC concentrations of 6047% biweekly, 222% daily, 97% hourly, and 35% quarter-hourly were observable, with the 15-min cycle of the dynamic headspace analysis. The headspace analyzer had superior retention time stability, required less maintenance, and had 1/4 the analysis time as a typical purge-and-trap-gas chromatograph system used for hourly comparisons.

  16. [Characterization of compounds in crude oils by gas purge micro-syringe extraction coupled to comprehensive two-dimensional gas chromatography].

    Science.gov (United States)

    Tong, Ting; Zhang, Wanfeng; Li, Donghao; Zhao, Jinhua; Chang, Zhenyang; Gao, Xuanbo; Dai, Wei; He, Sheng; Zhu, Shukui

    2014-10-01

    A novel sample pretreatment method, gas purge micro-syringe extraction (GP- MSE), coupled to comprehensive two-dimensional gas chromatography/time-of-flight mass spectrometry (GC x GC/TOFMS) has been developed for the characterization of volatile and semi-volatile compounds in crude oils. In the sample pretreatment process, the analytes were carried to the microsyringe barrel by inert gas, and at the same time, trapped by an organic solvent. The whole process of extraction takes less than 10 min, and only 20 μL of organic solvent was needed. Using two custom standard solutions containing alkanes and polycyclic aromatic hydrocarbons (PAHs), the influences of the extraction conditions were investigated. The optimized conditions were as follows: 5 mg crude oil, 20 μL hexane (extraction solvent), extraction for 3 min at 300 °C, condensation temperature set at -2 °C, gas flow rate set at 2 mL/min. Under the optimized conditions, a real crude oil sample was extracted and then analyzed in detail. It showed that the proposed method was very effective in simultaneously analyzing the normal and branched alkanes, cycloalkanes, aromatic hydrocarbons, and biomarkers of crude oil such as steranes and terpanes. The recoveries obtained ranged from 82.0% to 107.3% and the detection limits ranged from 34 to 93 μg/L. The correlation coefficients (R2) were more than 0.99. The relative standard deviations (RSDs, n = 5) for all the analytes were below 10%. The results indicate that the proposed method is suitable for the characterization of volatile and semi-volatile compounds in crude oils with easy operation, high sensitivity and efficiency.

  17. Platform development supportedby gaming

    DEFF Research Database (Denmark)

    Mikkola, Juliana Hsuan; Hansen, Poul H. Kyvsgård

    2007-01-01

    The challenge of implementing industrial platforms in practice can be described as a configuration problem caused by high number of variables, which often have contradictory influences on the total performance of the firm. Consequently, the specific platform decisions become extremely complex......, possibly increasing the strategic risks for the firm. This paper reports preliminary findings on platform management process at LEGO, a Danish toy company.  Specifically, we report the process of applying games combined with simulations and workshops in the platform development. We also propose a framework......, based on the portfolio management thinking, to measure the degree of modularity embedded in a given platform and to what extent it is aligned with other platforms....

  18. Reduced mate availability leads to evolution of self-fertilization and purging of inbreeding depression in a hermaphrodite.

    Science.gov (United States)

    Noël, Elsa; Chemtob, Yohann; Janicke, Tim; Sarda, Violette; Pélissié, Benjamin; Jarne, Philippe; David, Patrice

    2016-03-01

    Basic models of mating-system evolution predict that hermaphroditic organisms should mostly either cross-fertilize, or self-fertilize, due to self-reinforcing coevolution of inbreeding depression and outcrossing rates. However transitions between mating systems occur. A plausible scenario for such transitions assumes that a decrease in pollinator or mate availability temporarily constrains outcrossing populations to self-fertilize as a reproductive assurance strategy. This should trigger a purge of inbreeding depression, which in turn encourages individuals to self-fertilize more often and finally to reduce male allocation. We tested the predictions of this scenario using the freshwater snail Physa acuta, a self-compatible hermaphrodite that preferentially outcrosses and exhibits high inbreeding depression in natural populations. From an outbred population, we built two types of experimental evolution lines, controls (outcrossing every generation) and constrained lines (in which mates were often unavailable, forcing individuals to self-fertilize). After ca. 20 generations, individuals from constrained lines initiated self-fertilization earlier in life and had purged most of their inbreeding depression compared to controls. However, their male allocation remained unchanged. Our study suggests that the mating system can rapidly evolve as a response to reduced mating opportunities, supporting the reproductive assurance scenario of transitions from outcrossing to selfing.

  19. Multi-channel purge and trap system coupled with ion chromatography for the determination of alkylamines in cosmetics.

    Science.gov (United States)

    Zhong, Zhixiong; Li, Gongke; Luo, Zhibin; Zhu, Binghui

    2012-02-17

    A new multi-channel purge and trap system coupled with ion chromatography for the determination of six alkylamines in cosmetics was developed. The proposed method, based on purge and trap of the volatile alkylamines, involved in a miniaturization and multi-channel integration of classical steam distillation and a simple approach for routine labs. The procedure was rapidly achieved within 10 min and the matrix interferences could be effectively eliminated. Sample pretreatment frequency was higher than 40 h(-1). The linear ranges were 0.1-15 mg L(-1) and the detection limits varied from 0.023 to 0.038 mg L(-1). This method was successfully utilized to determine the amounts of alkylamines in cosmetics with recoveries ranging from 80.3 to 105.5% and the relative standard deviations (RSDs) ranging from 0.78 to 7.5%. It was proved to be accurate, time-saving, and suitable for the determination of large numbers of cosmetics in a short time.

  20. Theoretical Purge Factor Determination as a Control Strategy for Potential Mutagenic Impurities in the Synthesis of Drug Substances.

    Science.gov (United States)

    Kragelj Lapanja, Nevenka; Toplak Časar, Renata; Jurca, Sabina; Doljak, Bojan

    Mutagenic impurities (MIs) are of serious concern for pharmaceutical industry, regulatory agencies and public health. The first guideline addressing the control of genotoxic impurities (GTIs) dates back to 2006. Since then there have been several updates and refinements, which eventually resulted in the guideline, published by the International Conference on Harmonisation (ICH) in June 2014. The ICH M7 guideline, compared to previous ones, offers greater flexibility in terms of control strategies for GTIs in drug substances. More specifically, it describes a control strategy that relies on process controls in lieu of analytical testing which is based on understanding the process chemistry and process parameters that impact the levels of GTIs. This principle is adopted in the theoretical purge factor determination tool proposed by Teasdale et al. Several case studies applying the proposed theoretical purge factor determination tool were published in recent years. The results confirm the tool's good predictability of the extent to which the impurity is removed by the process. Hopefully, this approach will soon be released as an in-silico tool, generally accepted by the regulatory agencies.

  1. Interpersonal problems across restrictive and binge-purge samples: data from a community-based eating disorders clinic.

    Science.gov (United States)

    Raykos, Bronwyn C; McEvoy, Peter M; Carter, Olivia; Fursland, Anthea; Nathan, Paula

    2014-08-01

    Contemporary models of eating disorders suggest that interpersonal problems contribute to the maintenance of eating disorders. This study examined whether baseline interpersonal problems differed across eating disorder diagnoses and across eating disorder subtypes ("restrictors" vs. "binge-purge" patients) in a large clinical sample. Patients with a primary eating disorder diagnosis (N=406) completed measures of interpersonal problems, eating disorder symptoms, and mood prior to treatment at a specialist eating disorder clinic. Across the sample, more severe eating disorder psychopathology was associated with significantly greater difficulty socializing. Anorexia Nervosa (AN)/restrictor patients reported significantly greater difficulty socializing than Bulimia Nervosa (BN)/binge-purge patients. AN patients reported significantly greater difficulty on a measure of competitiveness/assertiveness compared to BN and Eating Disorder Not Otherwise Specified patients. All findings were significant after controlling for comorbid depression and anxiety symptoms. Interpersonal problems appear to be unique risk factors for eating disorders. Specific interpersonal mechanisms include difficulties socializing and being assertive, which were most pronounced in AN patients. These findings provide potential avenues for enhancing interventions, such as adjunctive assertiveness training for AN.

  2. DFH-3 Satellite Platform

    Institute of Scientific and Technical Information of China (English)

    RenShufang

    2005-01-01

    The DFH-3 satellite platform is designed and developed by China Academy of Space Technology (CAST). It is a medium capability communications satellite platform. The platform adopts threeaxis attitude stabilization control system, having solar array output power of 1.7kW by the end of its design lifetime of 8 years. Its mass is 2100kg with payload capacity of 220kg.

  3. Product Platform Replacements

    DEFF Research Database (Denmark)

    Sköld, Martin; Karlsson, Christer

    2012-01-01

    Purpose – It is argued in this article that too little is known about product platforms and how to deal with them from a manager's point of view. Specifically, little information exists regarding when old established platforms are replaced by new generations in R&D and production environments...... originality and value is achieved by focusing on product platform replacements believed to represent a growing management challenge....

  4. On the biological connectivity of oil and gas platforms in the North Sea.

    Science.gov (United States)

    Thorpe, S A

    2012-12-01

    Tests are made of the conjecture that the platforms in the North Sea are biologically connected, with organisms originating from some platforms reaching and substantially augmenting those at others so that, together, the platforms effectively form a sort of artificial reef. The M₂ tide results in a relatively rapid transfer of organisms between neighbouring platforms. Some 60% of platforms in the southern UK Sector are directly connected by tidal flows. Such connection in the northern Sector is relatively rare, about 23% of platforms being connected. Mean flows connect platforms in 'strings' sharing a common streamline spread by turbulent dispersion. Metrics are devised to indicate how well a particular platform is connected to others. Strings are broken when contributions to the concentration of organisms from platforms fall below detection limits. Many platforms are likely to be connected in strings in the southern UK Sector, but relatively few in the northern Sector.

  5. The pro-Franco purge of the primary teaching profession La depuración franquista del magisterio primario

    Directory of Open Access Journals (Sweden)

    Juan Manuel FERNÁNDEZ SORIA

    2013-09-01

    Full Text Available The purge of primary school teaching profession, like other groups, was an instrument of political repression organized and planned in order to establish, keep and legitimise the social-political «New Order» that aroze after the victory of Franco's army. There are three points to this article. The first point establishes the state of the question on the repressive nature and conditions in Franco's Spain. The repression adopted against the school teachers has its own quality: it is more preventive than punitive, trying with it to dissuade the pedagogue action of the teaching profession, a group who never had the confidence of the new regime nor the ideological mainstays which support it, including the catolical church. The second point tries to clear this mistrust, which goes back to the times of the Spanish Second Republic; in this mistrust the purge of the schoolteachers has its arguments. The third part studies the purge of Valencian schoolteachers, and analyses its political and social characteristics, concluding that an apolitical and scantily compromised group is purged essentially due to political accusations. Though the accusations were not harsh we can confirm the hypothesis of the preventive purge of the teaching profession, a group the Franco regime needed but kept by fear. The great lozers of this repression were not only the school teachers but the Spanish society itself. A society that saw how the new pedagogy under Franco's regime cut the progress that was finally underway only a few years prior.La purga de los maestros de escuela primaria, como la de otros grupos profesionales, fue un instrumento de la represión política organizada y planificada para establecer, conservar y legitimar el «nuevo orden» sociopolítico que se implanta después la victoria militar de Franco. En este artículo planteamos tres cuestiones. La primera realiza un estado de situación sobre la naturaleza de la represión y las condiciones de la Espa

  6. The Creative Platform

    DEFF Research Database (Denmark)

    Byrge, Christian; Hansen, Søren

    This book is about introducing more creativity into general educational courses and cross-disciplinary activities. It is directed toward teachers at all levels in the educational system, but the Creative Platform is a general model, and thus the creative process will fundamentally be the same...... whether you consider thirdgrade teaching, human-resource development, or radical new thinking in product development in a company. The Creative Platform was developed at Aalborg University through a series of research-and-development activities in collaboration with educational institutions and private...... you can use in your work with the Creative Platform. This book is intended as an introduction on how to use the Creative Platform....

  7. Omnidirectional holonomic platforms

    Energy Technology Data Exchange (ETDEWEB)

    Pin, F.G.; Killough, S.M.

    1994-06-01

    This paper presents the concepts for a new family of wheeled platforms which feature full omnidirectionality with simultaneous and independently controlled rotational and translational motion capabilities. The authors first present the orthogonal-wheels concept and the two major wheel assemblies on which these platforms are based. They then describe how a combination of these assemblies with appropriate control can be used to generate an omnidirectional capability for mobile robot platforms. The design and control of two prototype platforms are then presented and their respective characteristics with respect to rotational and translational motion control are discussed.

  8. 富氮气调在储粮应用中的问题探讨%Discussion about the Problem of Grain Storage by Purging Nitroren

    Institute of Scientific and Technical Information of China (English)

    李云霄; 陈宏斌

    2012-01-01

    By analyzing the current some problems in grain storage by purging nitroren, it Propose a solution, that reduce the application cost and improve the economic efficiency of grain storage by purging nltroren.%通过分析现行富氮气调储粮过程中存在的某些问题,提出解决方案,降低富氮气调储粮运行成本,提高富氮气调储粮的经济效益。

  9. Novel totally implantable trans-ventricular and cross-valvular cannular pump with rolling bearings and purge system for recovery therapy.

    Science.gov (United States)

    Qian, K X; Wang, D F; Topaz, S; Ru, W M; Zeng, P; Yuan, H Y; Zwischenberg, J B

    2007-01-01

    In the early 1990s, Yamazaki et al. developed a partly intra-ventricular pump, which was inserted into the left ventricle via the apex and then into the aorta through the aortic valve. The pump delivered blood flow directly from the left ventricle to the aorta, like a natural heart, and needed no inflow and outflow connecting tubes; it could be weaned off after the left ventricle had been recovered. The shortcomings were that the driving DC motor remained outside of the ventricle, causing an anatomic space problem, and the sealing and bearing were not appropriate for a durable device. Recently, a totally implantable trans-ventricular pump has been developed in the authors' laboratory. The device has a motor and a pump entirely contained within one cannula. The motor has a motor coil with iron core and a rotor with four-pole magnet; the pump has an impeller and an outflow guide vane. The motor part is 60 mm in length and 13 mm in diameter; the pump part is 55 mm in length and 11 mm in diameter. The total length of the device is therefore 115 mm. The total weight of the device is 53 g. The motor uses rolling bearing with eight needles on each side of the rotor magnets. A special purge system is devised for the infusion of saline mixed with heparin through bearing to the pump inlet (30 - 50 cc per hour). Thus neither mechanical wear nor thrombus formation along the bearing will occur. In haemodynamic testing, the pump can produce a flow of 4 l min-1 with 60 mmHg pressure increase, at a pump rotating speed of 12,500 rpm. At zero flow rate, corresponding to the diastolic period of the heart, the pump can maintain aortic blood pressure over 80 mmHg at the same rotating speed. This novel pump can be quickly inserted in an emergency and easily removed after recovery of natural heart. It will be useful for patients with acute left ventricular failure.

  10. Building National Innovation Platform in China

    DEFF Research Database (Denmark)

    Li, Jizhen; Deng, Quwen; Sørensen, Olav Jull

    2011-01-01

    The focus of the article is the "national innovation platform" that are being build in China to enhance interaction between stakeholders and encourage knowledge flows. The textile industry is used as an example to discuss suitablity and lay a foundation for theoretical reflections of the new...

  11. Building National Innovation Platform in China

    DEFF Research Database (Denmark)

    Li, Jizhen; Deng, Quwen; Sørensen, Olav Jull

    2011-01-01

    The focus of the article is the "national innovation platform" that are being build in China to enhance interaction between stakeholders and encourage knowledge flows. The textile industry is used as an example to discuss suitablity and lay a foundation for theoretical reflections of the new...

  12. Advanced offshore oil platforms

    Energy Technology Data Exchange (ETDEWEB)

    Ellers, F.S.

    1982-04-01

    Four innovative offshore platforms that are designed to withstand 100-foot waves in waters 600-feet deep are described. These platforms are: (1) Stratfjord B Concrete Gravity-Base Platform; (2) Magnus Steel-Template-Jacket Platform; (3) Hutton Tension-Leg Platform; and (4) Block 280 Guyed Tower. The Statfjord B platform, designed in Norway, rests on four massive concrete columns with storage tanks at the base. It depends solely on its own mass for stability. The Magnus platform, designed by the British, is the heaviest offshore platform yet fabricated, weighing 41,000 tons. Two of the platform's four legs will incorporate flotation chambers so that the structure can be floated to its site in the North Sea. The Hutton structure, also designed in England, will consist of a buoyant hull tethered to the sea floor by slender steel tubes at its four corners. The first platform of its type, the Hutton structure is also destined for the North Sea. The US designed Block 280 guyed tower is designed for service in the Gulf of Mexico in water 1000 feet deep. It will be pinned to the sea floor by a spokelike array of 20 steel cables, each one more than 3000 feet long. The tower and its guys will weigh 43,000 tons, slightly more than the Magnus steel-template jacket and more than four time as much as the Eiffel Tower. At a cost of approximately $2.6 billion, the Magnus is the most expensive offshore platform to date. The Statfjord B was put into production in 1982. The Magnus is scheduled for oil production in 1983. The Hutton and the Block 280 will both be producing in 1984. (JMT)

  13. Media Flow

    DEFF Research Database (Denmark)

    Kabel, Lars

    2016-01-01

    News and other kinds of journalistic stories, 16-17 hours a day, all year round, on all platforms, also the moderated social media. The key research thesis behind this article is that the continuous and speedy stream of news stories and media content now is becoming the centre of the production...... processes and the value creation in converged multimedia newsrooms. The article identify new methods and discuss editorial challenges in handling media flow....

  14. EURESCOM Services Platform

    NARCIS (Netherlands)

    Nieuwenhuis, Lambertus Johannes Maria; van Halteren, Aart

    1999-01-01

    This paper presents the results of the EURESCOM Project 715. In February 1999, a large team of researchers from six European public network operators completed a two year period of cooperative experiments on a TINA-based environment, called the EURESCOM Services Platform (ESP). This platform

  15. 甲醇合成环路弛放气深度利用%Optimal utilization of purge gas from the synthesis loop of methanol plant

    Institute of Scientific and Technical Information of China (English)

    何洋

    2012-01-01

    For the problem that the purge gas from the synthesis loop of methanol plant wasn't utilized in high value, an optimal utilization of the purge gas to double its value was proposed, which was to separate all the components from the purge gas by cryogenic method for more valuable use. The proposed concept is valuable for promotion. Especially for the natural gas-based methanol coproduction plants, it could provide a good way for utilizing the purge gas better and also regulate the methanol output.%针对甲醇装置合成环路弛放气价值普遍未得到充分利用的问题,提出了将甲醇弛放气深冷分离提纯各组分,然后分别加以优化利用的思路,实现价值翻倍.同时,该思路也具有推广价值和借鉴意义.特别是针对以天然气为原料联产甲醇的化工企业来说,既可更好地利用弛放气,还可调节甲醇产量.

  16. Molecular purging of multiple myeloma cells by ex-vivo culture and retroviral transduction of mobilized-blood CD34+ cells

    Directory of Open Access Journals (Sweden)

    Corneo Gianmarco

    2007-07-01

    Full Text Available Abstract Background Tumor cell contamination of the apheresis in multiple myeloma is likely to affect disease-free and overall survival after autografting. Objective To purge myeloma aphereses from tumor contaminants with a novel culture-based purging method. Methods We cultured myeloma-positive CD34+ PB samples in conditions that retained multipotency of hematopoietic stem cells, but were unfavourable to survival of plasma cells. Moreover, we exploited the resistance of myeloma plasma cells to retroviral transduction by targeting the hematopoietic CD34+ cell population with a retroviral vector carrying a selectable marker (the truncated form of the human receptor for nerve growth factor, ΔNGFR. We performed therefore a further myeloma purging step by selecting the transduced cells at the end of the culture. Results Overall recovery of CD34+ cells after culture was 128.5%; ΔNGFR transduction rate was 28.8% for CD34+ cells and 0% for CD138-selected primary myeloma cells, respectively. Recovery of CD34+ cells after ΔNGFR selection was 22.3%. By patient-specific Ig-gene rearrangements, we assessed a decrease of 0.7–1.4 logs in tumor load after the CD34+ cell selection, and up to 2.3 logs after culture and ΔNGFR selection. Conclusion We conclude that ex-vivo culture and retroviral-mediated transduction of myeloma leukaphereses provide an efficient tumor cell purging.

  17. An investigation of the joint longitudinal trajectories of low body weight, binge eating, and purging in women with anorexia nervosa and bulimia nervosa.

    Science.gov (United States)

    Lavender, Jason M; De Young, Kyle P; Franko, Debra L; Eddy, Kamryn T; Kass, Andrea E; Sears, Meredith S; Herzog, David B

    2011-12-01

    To describe the longitudinal course of three core eating disorder symptoms-low body weight, binge eating, and purging-in women with anorexia nervosa (AN) and bulimia nervosa (BN) using a novel statistical approach. Treatment-seeking women with AN (n = 136) or BN (n = 110) completed the Eating Disorders Longitudinal Interval Follow-Up Evaluation interview every 6 months, yielding weekly eating disorder symptom data for a 5-year period. Semiparametric mixture modeling was used to identify longitudinal trajectories for the three core symptoms. Four individual trajectories were identified for each eating disorder symptom. The number and general shape of the individual trajectories was similar across symptoms, with each model including trajectories depicting stable absence and stable presence of symptoms as well as one or more trajectories depicting the declining presence of symptoms. Unique trajectories were found for low body weight (fluctuating presence) and purging (increasing presence). Conjunction analyses yielded the following joint trajectories: low body weight and binge eating, low body weight and purging, and binge eating and purging. The course of individual eating disorder symptoms among patients with AN and BN is highly variable. Future research identifying clinical predictors of trajectory membership may inform treatment and nosological research. Copyright © 2010 Wiley Periodicals, Inc.

  18. Differential neural correlates of set-shifting in the bingeing-purging and restrictive subtypes of anorexia nervosa : An fMRI study

    NARCIS (Netherlands)

    Van Autreve, Sara; De Baene, W.; Baeken, Chris; van Heeringen, Kees; Vancayseele, Nikita; Vervaet, Myriam

    2016-01-01

    In this study, possible differences in the neural correlates of set-shifting abilities between the restrictive (AN-R) and bingeing/purging (AN-BP) subtypes of anorexia nervosa have been explored. Three groups of participants performed a set-shifting task during functional magnetic resonance imaging:

  19. Calorie estimation accuracy and menu labeling perceptions among individuals with and without binge eating and/or purging disorders.

    Science.gov (United States)

    Roberto, Christina A; Haynos, Ann F; Schwartz, Marlene B; Brownell, Kelly D; White, Marney A

    2013-09-01

    Menu labeling is a public health policy that requires chain restaurants in the USA to post kilocalorie information on their menus to help consumers make informed choices. However, there is concern that such a policy might promote disordered eating. This web-based study compared individuals with self-reported binge eating disorder (N = 52), bulimia nervosa (N = 25), and purging disorder (N = 17) and those without eating disorders (No ED) (N = 277) on restaurant calorie information knowledge and perceptions of menu labeling legislation. On average, people answered 1.46 ± 1.08 questions correctly (out of 6) (25%) on a calorie information quiz and 92% of the sample was in favor of menu labeling. The findings did not differ based on eating disorder, dieting, or weight status, or race/ethnicity. The results indicated that people have difficulty estimating the calories in restaurant meals and individuals with and without eating disorders are largely in favor of menu labeling laws.

  20. A comparison of the metabolic complications and hospital course of severe anorexia nervosa by binge-purge and restricting subtypes.

    Science.gov (United States)

    Rylander, Melanie; Brinton, John T; Sabel, Allison L; Mehler, Philip S; Gaudiani, Jennifer L

    2017-01-06

    This study examines adult patients with severe, life-threatening anorexia nervosa who were admitted to an inpatient, medical stabilization unit between October 1, 2008 and December 31, 2014. Specifically, the study compares anorexia nervosa, binge purge subtype (AN-BP) and anorexia nervosa, restricting subtype (AN-R) on admission measures, hospital course, and outcomes. Of the 232 patients, 46% (N = 108) had AN-BP. Patients with AN-R manifested a higher frequency of underweight-mediated medical complications, including bone marrow dysfunction, hepatic dysfunction, and hypoglycemia. Understanding the pathophysiologic differences between severe AN-R and AN-BP is essential to understanding the abnormalities seen on clinical presentation, guiding appropriate clinical treatment, and predicting medical complications during refeeding.

  1. 推出增强的Purging Recorvery System大块清除料再生系统

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    美奎产品有限公司(以下简称“美奎”)近日宣布,该公司增强了其用于将大块清除料转变为再生料的Purging Recovery SystemTM(PRS),并且已经获得了在欧洲销售PRS所需的CE认证。美奎将会在NPE2012展会中重点推介PRS的新功能,并且提供数据来展示该系统可通过回收废品材料来快速收回投资成本。

  2. Determination of biodegradation process of benzene, toluene, ethylbenzene and xylenes in seabed sediment by purge and trap gas chromatography

    Energy Technology Data Exchange (ETDEWEB)

    Han, Dongqiang [Key Lab. for Atomic and Molecular Nanosciences of Education Ministry, Tsinghua Univ., Beijing (China). Dept. of Physics; China Pharmaceutical Univ., Nanjing (China). Physics Teaching and Research Section, Dept. of Basic Sciences; Ma, Wanyun; Chen, Dieyan [Key Lab. for Atomic and Molecular Nanosciences of Education Ministry, Tsinghua Univ., Beijing (China). Dept. of Physics

    2007-12-15

    Benzene, toluene, ethylbenzene, and xylenes (BTEX) are commonly found in crude oil and are used in geochemical investigations as direct indicators of the presence of oil and gas. BTEX are easily volatile and can be degraded by microorganisms, which affect their precise measurement seriously. A method for determining the biodegradation process of BTEX in seabed sediment using dynamic headspace (purge and trap) gas chromatography with a photoionization detector (PID) was developed, which had a detection limit of 7.3-13.2 ng L{sup -1} and a recovery rate of 91.6-95.0%. The decrease in the concentration of BTEX components was monitored in seabed sediment samples, which was caused by microorganism biodegradation. The results of BTEX biodegradation process were of great significance in the collection, transportation, preservation, and measurement of seabed sediment samples in the geochemical investigations of oil and gas. (orig.)

  3. The Common HOL Platform

    OpenAIRE

    Adams, Mark

    2015-01-01

    The Common HOL project aims to facilitate porting source code and proofs between members of the HOL family of theorem provers. At the heart of the project is the Common HOL Platform, which defines a standard HOL theory and API that aims to be compatible with all HOL systems. So far, HOL Light and hol90 have been adapted for conformance, and HOL Zero was originally developed to conform. In this paper we provide motivation for a platform, give an overview of the Common HOL Platform's theory and...

  4. Ladder attachment platform

    Science.gov (United States)

    Swygert,; Richard, W [Springfield, SC

    2012-08-28

    A ladder attachment platform is provided that includes a base for attachment to a ladder that has first and second side rails and a plurality of rungs that extend between in a lateral direction. Also included is a user platform for having a user stand thereon that is carried by the base. The user platform may be positioned with respect to the ladder so that it is not located between a first plane that extends through the first side rail and is perpendicular to the lateral direction and a second plane that extends through the second side rail and is perpendicular to the lateral direction.

  5. Increased survival of normal cells during laser photodynamic therapy: implications for ex vivo autologous bone marrow purging

    Energy Technology Data Exchange (ETDEWEB)

    Gulliya, K.S.; Matthews, J.L.; Fay, J.W.; Dowben, R.M.

    1988-01-01

    Laser light-induced, dye-mediated photolysis of leukemic cells was tested in an in vitro model for its efficacy in eliminating occult tumor cells for ex vivo autologous bone marrow purging. Merocyanine 540 (MC540) was mixed with acute promyelocytic leukemia (HL-60) cells in the presence of human albumin. This cell-dye mixture was irradiated with 514 nm argon laser light. Results show that in the presence of 0.1%, 0.25% and 0.5% albumin, laser light doses of 62.4 J/cm/sup 2/, 93.6 J/cm/sup 2/ and 109.2 J/cm/sup 2/, respectively, were required for a 5 log reduction in the survival of leukemic cells. Under identical conditions, 80% to 84% of the normal bone marrow cells and 41% of the granulocyte-macrophage colony forming cells survived. The number of surviving stromal cells was reduced (1+) compared to the untreated control (4+). Mixing of irradiated bone marrow cells with equal number of HL-60 cells did not interfere with the killing of HL-60 cells treated with MC540 and laser light. The non-specific cytotoxicity of laser light alone was less than 6% for normal bone marrow cells. These results suggest that the concentration of human albumin plays an important role in laser light-induced phototoxicity. This laser light-induced selective photolysis of leukemic cells can be used in ex vivo purging of tumor cell-contaminated bone marrow grafts to achieve very high survival rates of normal bone marrow cells and granulocyte-macrophage colony forming cells.

  6. Simulation platform of navigation system for autonomous underwater vehicle

    Institute of Scientific and Technical Information of China (English)

    QIN Zheng; BIAN Xin-qian

    2006-01-01

    In view of the characteristics of underwater navigation, the simulation platform of navigation system for autonomous underwater vehicle has been developed based on Windows platform. The system architecture, net communication and the information flow are discussed. The methods of software realization and some key techniques of the Vehicle Computer and the Navigation Equipment Computer are introduced in particular. The software design of Terrain Matching Computer is introduced also. The simulation platform is verified and analyzed through simulation. The results show that the architecture of the platform is reasonable and reliable, and the mathematic models and simulation algorithms of sub-systems are also valid and practicable.

  7. Stress field distribution of purging plug for ladle in application process%钢包透气砖服役过程中应力分布研究

    Institute of Scientific and Technical Information of China (English)

    杨文刚; 刘国齐; 王建国; 于建宾; 马天飞; 钱凡

    2013-01-01

    The stress field distribution of purging plug during service was analyzed by ANSYS finite element software. The results are shown as follows. (l)The stress of purging plug is the highest at the argon blowing stage and reaches the maximum at the end of argon blowing;at this moment,the hot face of purging plug is mainly affected by radial and circumferential compressive stress,and the inside of purging plug is mainly affected by the radial,circumferential and axial tensile stress. (2)The damages of purging plug are mainly occurred in two parts:one is around slit in hot surface,as the compressive stress is large,which tends to produce cracks or spading;the other is 74 mm away from the hot face,as the tensile stress is large,which tends to cross-break.%利用Ansys有限元分析软件对钢包透气砖服役过程中的应力分布进行了研究.结果表明:透气砖在服役过程中,吹氩阶段所受热应力最大,在吹氩结束的瞬间达到最大值,此时透气砖工作面主要受径向和周向的压应力,透气砖内部主要受径向、周向和轴向的拉应力;透气砖损毁主要出现在两个部位,一是工作面狭缝周围由于压应力大易产生裂纹或者剥落,二是在距透气砖工作面74 mm的位置由于拉应力大易发生横断损毁.

  8. Platform-based production development

    DEFF Research Database (Denmark)

    Bossen, Jacob; Brunoe, Thomas Ditlev; Nielsen, Kjeld

    2015-01-01

    Platforms as a means for applying modular thinking in product development is relatively well studied, but platforms in the production system has until now not been given much attention. With the emerging concept of platform-based co-development the importance of production platforms is though...... indisputable. This paper presents state-of-the-art literature on platform research related to production platforms and investigates gaps in the literature. The paper concludes on findings by proposing future research directions....

  9. USA Hire Testing Platform

    Data.gov (United States)

    Office of Personnel Management — The USA Hire Testing Platform delivers tests used in hiring for positions in the Federal Government. To safeguard the integrity of the hiring processes and ensure...

  10. MULTIFUNCTIONAL PLATFORMS AND

    African Journals Online (AJOL)

    Solar service centres and multifunctional platforms are innovative concepts for providing energy services in ... same time generate income. obeng ..... communities the driving force behind the ... operator(s) had to contact repairers outside their.

  11. The Common HOL Platform

    Directory of Open Access Journals (Sweden)

    Mark Adams

    2015-07-01

    Full Text Available The Common HOL project aims to facilitate porting source code and proofs between members of the HOL family of theorem provers. At the heart of the project is the Common HOL Platform, which defines a standard HOL theory and API that aims to be compatible with all HOL systems. So far, HOL Light and hol90 have been adapted for conformance, and HOL Zero was originally developed to conform. In this paper we provide motivation for a platform, give an overview of the Common HOL Platform's theory and API components, and show how to adapt legacy systems. We also report on the platform's successful application in the hand-translation of a few thousand lines of source code from HOL Light to HOL Zero.

  12. The Creative Platform

    DEFF Research Database (Denmark)

    Byrge, Christian; Hansen, Søren

    whether you consider thirdgrade teaching, human-resource development, or radical new thinking in product development in a company. The Creative Platform was developed at Aalborg University through a series of research-and-development activities in collaboration with educational institutions and private......This book is about introducing more creativity into general educational courses and cross-disciplinary activities. It is directed toward teachers at all levels in the educational system, but the Creative Platform is a general model, and thus the creative process will fundamentally be the same...... companies. It is a project in which the goal is to make a hands-on approach to a knowledge perspective on enhancing creativity. The underlying ambition of the Creative Platform is to make it easier to promote creativity. At www.uka.aau.dk/The+Creative+Platform, you can find extra materials and instructions...

  13. National Community Solar Platform

    Energy Technology Data Exchange (ETDEWEB)

    Rupert, Bart [Clean Energy Collective, Louisville, CO (United States)

    2016-06-30

    This project was created to provide a National Community Solar Platform (NCSP) portal known as Community Solar Hub, that is available to any entity or individual who wants to develop community solar. This has been done by providing a comprehensive portal to make CEC’s solutions, and other proven community solar solutions, externally available for everyone to access – making the process easy through proven platforms to protect subscribers, developers and utilities. The successful completion of this project provides these tools via a web platform and integration APIs, a wide spectrum of community solar projects included in the platform, multiple groups of customers (utilities, EPCs, and advocates) using the platform to develop community solar, and open access to anyone interested in community solar. CEC’s Incubator project includes web-based informational resources, integrated systems for project information and billing systems, and engagement with customers and users by community solar experts. The combined effort externalizes much of Clean Energy Collective’s industry-leading expertise, allowing third parties to develop community solar without duplicating expensive start-up efforts. The availability of this platform creates community solar projects that are cheaper to build and cheaper to participate in, furthering the goals of DOE’s SunShot Initiative. Final SF 425 Final SF 428 Final DOE F 2050.11 Final Report Narrative

  14. Architectural view model for an integration platform

    Directory of Open Access Journals (Sweden)

    Tomasz Górski

    2012-03-01

    Full Text Available The most common architectural view model is "4+1" by Philipe Kruchten. This model presents the views required for a full description of computer system architecture. By contrast, this model seems to be insufficient to describe architecture of integration platform. Definitely lacks the view of integrated business processes. In the serviceoriented approach, one of the basic elements is a contract. It should also be included in the description of the architecture. Moreover, very important are integration mechanisms and mediation flows that should be presented in the description of architecture. Hence the need for integrated services view, and manner of their integration on the enterprise service bus. Use case view should also be extended by stereotypes required for presenting functionality exposed for other computer systems. It is therefore proposed architectural view model “1+5” for an integration platform. This model has following architectural views: Integrated processes, Use Cases, Logical, Integrated Services, Contracts, Deployment. Furthermore, in article was presented new UML profile "UML Profile for Integration Flows". In the profile were placed stereotypes corresponding to integration patterns and mediation mechanisms. It is important, that UML activity diagram was extended and its special form was obtained to model mediation flows on integration platform. Thus was proposed a new UML diagram: mediation flows diagram.

  15. Toward an E-Government Semantic Platform

    Science.gov (United States)

    Sbodio, Marco Luca; Moulin, Claude; Benamou, Norbert; Barthès, Jean-Paul

    This chapter describes the major aspects of an e-government platform in which semantics underpins more traditional technologies in order to enable new capabilities and to overcome technical and cultural challenges. The design and development of such an e-government Semantic Platform has been conducted with the financial support of the European Commission through the Terregov research project: "Impact of e-government on Territorial Government Services" (Terregov 2008). The goal of this platform is to let local government and government agencies offer online access to their services in an interoperable way, and to allow them to participate in orchestrated processes involving services provided by multiple agencies. Implementing a business process through an electronic procedure is indeed a core goal in any networked organization. However, the field of e-government brings specific constraints to the operations allowed in procedures, especially concerning the flow of private citizens' data: because of legal reasons in most countries, such data are allowed to circulate only from agency to agency directly. In order to promote transparency and responsibility in e-government while respecting the specific constraints on data flows, Terregov supports the creation of centrally controlled orchestrated processes; while the cross agencies data flows are centrally managed, data flow directly across agencies.

  16. Vertical Wave Impacts on Offshore Wind Turbine Inspection Platforms

    DEFF Research Database (Denmark)

    Bredmose, Henrik; Jacobsen, Niels Gjøl

    2011-01-01

    on a horizontal inspection platform is computed for five different platform levels. The computational results show details of monopile impact such as slamming pressures from the overturning wave front and the formation of run-up flow. The results show that vertical platform impacts can occur at 20 m water depth....... The dependence of the vertical platform load to the platform level is discussed. Attention is given to the significant downward force that occur after the upward force associated with the vertical impact. The effect of the numerical resolution on the results is assessed. The position of wave overturning is found...... to be influenced by the grid resolution. For the lowest platform levels, the vertical impact is found to contribute to the peak values of in-line force and overturning moment....

  17. The Platformization of the Web: Making Web Data Platform Ready

    NARCIS (Netherlands)

    A. Helmond

    2015-01-01

    In this article, I inquire into Facebook’s development as a platform by situating it within the transformation of social network sites into social media platforms. I explore this shift with a historical perspective on, what I refer to as, platformization, or the rise of the platform as the dominant

  18. Comparison of numerical results and multicavity purge and rim seal data with extensions to dynamics

    Science.gov (United States)

    Athavale, Mahesh; Przekwas, Andrzej J.; Hendricks, Robert C.; Steinetz, Bruce M.

    1995-05-01

    The computation of flows within interconnected, multiple-disk cavities shows strong interaction between the cavities and the power stream. For this reason, simulations of single cavities in such cases are not realistic; the complete, linked configuration must be considered. Unsteady flow fields affect engine stability and can engender power-stream-driven secondary flows that produce local hot spotting or general cavity heating. Further, a concentric whirling rotor produces a circumferential pressure wave, but a statically eccentric whirling rotor produces a radial wave; both waves affect cavity ingestion and the stability of the entire engine. It is strongly suggested that seals be used to enhance turbojet engine stability. Simple devices, such as swirl brakes, honeycomb inserts, and new seal configurations, should be considered. The cost effectiveness of the NASA Lewis Research Center seals program can be expressed in terms of program goals (e.g., the Integrated High-pressure/Temperature Engine Technology (IHPTET) cannot be achieved without such a program), cost (savings to $250 million/1-percent decrease in specific fuel consumption), and indirect benefits (reduction of atmospheric NO(x) and CO2 and reduction of powerplant downtime).

  19. Platform Performance and Challenges - using Platforms in Lego Company

    DEFF Research Database (Denmark)

    Munk, Lone; Mortensen, Niels Henrik

    2009-01-01

    by the product defining users (product developers) and platform erosion. When the platforms are not used it is due to: unsuitable calculation models, lack of goals, rewards or benefits from management, unattractive tradeoffs and difficulties in understanding the platform. This indicates that platform design...... needs focus on the incentive of using the platform. This problem lacks attention in literature, as well as industry, where assessment criteria do not cover this aspect. Therefore, we recommend including user incentive in platform assessment criteria to these challenges. Concrete solution elements...... ensuring user incentive in platforms is an object for future research...

  20. Integrated microfluidic platforms for investigating neuronal networks

    Science.gov (United States)

    Kim, Hyung Joon

    This dissertation describes the development and application of integrated microfluidics-based assay platforms to study neuronal activities in the nervous system in-vitro. The assay platforms were fabricated using soft lithography and micro/nano fabrication including microfluidics, surface patterning, and nanomaterial synthesis. The use of integrated microfluidics-based assay platform allows culturing and manipulating many types of neuronal tissues in precisely controlled microenvironment. Furthermore, they provide organized multi-cellular in-vitro model, long-term monitoring with live cell imaging, and compatibility with molecular biology techniques and electrophysiology experiment. In this dissertation, the integrated microfluidics-based assay platforms are developed for investigation of neuronal activities such as local protein synthesis, impairment of axonal transport by chemical/physical variants, growth cone path finding under chemical/physical cues, and synaptic transmission in neuronal circuit. Chapter 1 describes the motivation, objectives, and scope for developing in-vitro platform to study various neuronal activities. Chapter 2 introduces microfluidic culture platform for biochemical assay with large-scale neuronal tissues that are utilized as model system in neuroscience research. Chapter 3 focuses on the investigation of impaired axonal transport by beta-Amyloid and oxidative stress. The platform allows to control neuronal processes and to quantify mitochondrial movement in various regions of axons away from applied drugs. Chapter 4 demonstrates the development of microfluidics-based growth cone turning assay to elucidate the mechanism underlying axon guidance under soluble factors and shear flow. Using this platform, the behaviors of growth cone of mammalian neurons are verified under the gradient of inhibitory molecules and also shear flow in well-controlled manner. In Chapter 5, I combine in-vitro multicellular model with microfabricated MEA

  1. Transactional Network Platform: Applications

    Energy Technology Data Exchange (ETDEWEB)

    Katipamula, Srinivas; Lutes, Robert G.; Ngo, Hung; Underhill, Ronald M.

    2013-10-31

    In FY13, Pacific Northwest National Laboratory (PNNL) with funding from the Department of Energy’s (DOE’s) Building Technologies Office (BTO) designed, prototyped and tested a transactional network platform to support energy, operational and financial transactions between any networked entities (equipment, organizations, buildings, grid, etc.). Initially, in FY13, the concept demonstrated transactions between packaged rooftop air conditioners and heat pump units (RTUs) and the electric grid using applications or "agents" that reside on the platform, on the equipment, on a local building controller or in the Cloud. The transactional network project is a multi-lab effort with Oakridge National Laboratory (ORNL) and Lawrence Berkeley National Laboratory (LBNL) also contributing to the effort. PNNL coordinated the project and also was responsible for the development of the transactional network (TN) platform and three different applications associated with RTUs. This document describes two applications or "agents" in details, and also summarizes the platform. The TN platform details are described in another companion document.

  2. Identification of platform levels

    DEFF Research Database (Denmark)

    Mortensen, Niels Henrik

    2005-01-01

    reduction, ability to launch a wider product portfolio without increasing resources and reduction of complexity within the whole company. To support the multiple product development process, platform based product development has in many companies such as Philips, VW, Ford etc. proven to be a very effective...... because the nature of developing platforms and applications are very different. In single product development reuse is often determined by individual designers, in multiple product development reuse is to a large degree a management issue. It is difficult for a company to switch from single to multiple...... development will be examined. Based on the identification of the above characteristics five platform levels are described. The research presented in this paper is a result of MSc, Ph.D projects at the Technical University of Denmark and consultancy projects within the organisation of Institute of Product...

  3. Universal visualization platform

    Science.gov (United States)

    Gee, Alexander G.; Li, Hongli; Yu, Min; Smrtic, Mary Beth; Cvek, Urska; Goodell, Howie; Gupta, Vivek; Lawrence, Christine; Zhou, Jainping; Chiang, Chih-Hung; Grinstein, Georges G.

    2005-03-01

    Although there are a number of visualization systems to choose from when analyzing data, only a few of these allow for the integration of other visualization and analysis techniques. There are even fewer visualization toolkits and frameworks from which one can develop ones own visualization applications. Even within the research community, scientists either use what they can from the available tools or start from scratch to define a program in which they are able to develop new or modified visualization techniques and analysis algorithms. Presented here is a new general-purpose platform for constructing numerous visualization and analysis applications. The focus of this system is the design and experimentation of new techniques, and where the sharing of and integration with other tools becomes second nature. Moreover, this platform supports multiple large data sets, and the recording and visualizing of user sessions. Here we introduce the Universal Visualization Platform (UVP) as a modern data visualization and analysis system.

  4. Geostationary multipurpose platforms

    Science.gov (United States)

    Bekey, I.; Bowman, R. M.

    1981-01-01

    In addition to the advantages generally associated with orbital platforms, such as improved reliability, economies of scale, simple connectivity of elements, reduced tracking demands and the restraint of orbital object population growth, geostationary platforms yield: (1) continuous access by fixed ground antennas for communications services; (2) continuous monitoring of phenomena over chosen regions of the earth's surface; (3) a preferred location for many solar-terrestrial physics experiments. The geostationary platform also offers a low-risk and economical solution to the impending saturation of the orbital arc/frequency spectrum, maximizing the capacity of individual slots and increasing the utility of the entire arc. It also allows the use of many small, simple and inexpensive earth stations through complexity inversion and high power per beam. Block diagram and operational flowcharts are provided.

  5. Platforms for antibiotic discovery.

    Science.gov (United States)

    Lewis, Kim

    2013-05-01

    The spread of resistant bacteria, leading to untreatable infections, is a major public health threat but the pace of antibiotic discovery to combat these pathogens has slowed down. Most antibiotics were originally isolated by screening soil-derived actinomycetes during the golden era of antibiotic discovery in the 1940s to 1960s. However, diminishing returns from this discovery platform led to its collapse, and efforts to create a new platform based on target-focused screening of large libraries of synthetic compounds failed, in part owing to the lack of penetration of such compounds through the bacterial envelope. This article considers strategies to re-establish viable platforms for antibiotic discovery. These include investigating untapped natural product sources such as uncultured bacteria, establishing rules of compound penetration to enable the development of synthetic antibiotics, developing species-specific antibiotics and identifying prodrugs that have the potential to eradicate dormant persisters, which are often responsible for hard-to-treat infections.

  6. Windows Azure Platform

    CERN Document Server

    Redkar, Tejaswi

    2011-01-01

    The Windows Azure Platform has rapidly established itself as one of the most sophisticated cloud computing platforms available. With Microsoft working to continually update their product and keep it at the cutting edge, the future looks bright - if you have the skills to harness it. In particular, new features such as remote desktop access, dynamic content caching and secure content delivery using SSL make the latest version of Azure a more powerful solution than ever before. It's widely agreed that cloud computing has produced a paradigm shift in traditional architectural concepts by providin

  7. Windows Azure Platform

    CERN Document Server

    Redkar, Tejaswi

    2010-01-01

    The Azure Services Platform is a brand-new cloud-computing technology from Microsoft. It is composed of four core components-Windows Azure, .NET Services, SQL Services, and Live Services-each with a unique role in the functioning of your cloud service. It is the goal of this book to show you how to use these components, both separately and together, to build flawless cloud services. At its heart Windows Azure Platform is a down-to-earth, code-centric book. This book aims to show you precisely how the components are employed and to demonstrate the techniques and best practices you need to know

  8. Wireless sensor platform

    Energy Technology Data Exchange (ETDEWEB)

    Joshi, Pooran C.; Killough, Stephen M.; Kuruganti, Phani Teja

    2017-08-08

    A wireless sensor platform and methods of manufacture are provided. The platform involves providing a plurality of wireless sensors, where each of the sensors is fabricated on flexible substrates using printing techniques and low temperature curing. Each of the sensors can include planar sensor elements and planar antennas defined using the printing and curing. Further, each of the sensors can include a communications system configured to encode the data from the sensors into a spread spectrum code sequence that is transmitted to a central computer(s) for use in monitoring an area associated with the sensors.

  9. Mobile4D platform

    CSIR Research Space (South Africa)

    Botha, Adèle

    2010-05-01

    Full Text Available . It is a communication platform that has architecture for creating, deploying and managing services and applications by integrating voice, video and data across a range of IP and telecom communication networks. In 2007, Red Hat made a firm commitment... based on the Mobicents muni ations Platform brand. 2.1.5  Telco specific User‐Generated Services   A variety of communication network operators have started initiatives to address User- Generated Services for the Telecom domain. Some...

  10. Design and Development of Fire Gridding Platform Based on Internet of Things

    Directory of Open Access Journals (Sweden)

    Wei San-Xi

    2016-01-01

    Full Text Available This article describes the construction background about fire gridding platform, reviews the research and progress in fire Internet of Things and fire gridding. The platform includes perception / execution layer, field control layer, network layer, center platform layer and application layer, which provide a good bonding about site control and remote monitoring. This article supplies a detail design for the main functions of application and task flow of fire hazard investigation. At the same time, a digital management platform was developed.

  11. The Role of Non-suicidal Self-Injury and Binge-Eating/Purging Behaviours in the Caregiving Experience Among Mothers and Fathers of Adolescents with Eating Disorders.

    Science.gov (United States)

    Depestele, Lies; Lemmens, Gilbert M D; Dierckx, Eva; Baetens, Imke; Schoevaerts, Katrien; Claes, Laurence

    2016-05-01

    This study investigated the caregiving experiences of mothers and fathers of restrictive and binge-eating/purging eating disordered (ED) inpatients with and without non-suicidal self-injury (NSSI). Sixty-five mothers and 65 fathers completed the Experience of Caregiving Inventory. All inpatients completed the Self-Injury Questionnaire-Treatment Related to assess NSSI and the Eating Disorder Evaluation Scale to assess eating disorder symptoms. Mothers reported significant more negative and more positive caregiving experiences compared with fathers. Mothers (but not fathers) of restrictive ED patients reported more positive caregiving experiences compared with mothers of binge-eating/purging patients. The presence of NSSI in ED patients was associated with more negative caregiving experiences of both parents. Mothers and fathers of ED inpatients differ in caregiving experiences, and both binge-eating behaviours and NSSI negatively affect their caregiving experience. Therefore, supportive interventions for parents of ED patients are necessary, especially of those patients who engage in NSSI.

  12. 聚丙烯料仓脱气压降算法研究%Research of Calculation Method for Pressure Drop in Purging of Polypropylene Silo

    Institute of Scientific and Technical Information of China (English)

    汪洋; 邢桂坤

    2015-01-01

    料仓脱气可以有效减少聚丙烯料仓闪爆事故的发生。介绍了聚丙烯粒料料仓脱气的工艺流程,着重论述了在颗粒床层的实际环境中料仓脱气压降的计算方法,并通过实际工程案例对该方法进行验证。%Purging in silo can efficiently avoid the occurrence possibility of explosion in polypropylene silo. In this paper, the flow process of purging in polypropylene silo was introduced. The calculation of pressure drop in purging process under the condition of pellet bed was emphatically described, and with practical example this method was verified.

  13. Preparation and application of purging upper nozzle for continuous casting tundish%连铸中间包透气上水口的研制与应用

    Institute of Scientific and Technical Information of China (English)

    徐志伟; 陈荣

    2000-01-01

    Property and variety of purging upper nozzle and the requirement of continuous casting process for thenozzle were introduced. Using synthetic mullite,α-Al2 O3 and special binder prepared the dispersion mullitebased purging upper nozzle. The nozzle was used in large-sized steel plant such as Baosteel, etc, gain-ing good results.%介绍了连铸中间包透气上水口的性能和种类及连铸工艺对透气上水口性能的要求。利用合成莫来石颗粒、α-Al2O3细粉及特殊结合剂研制了弥散型莫来石质透气上水口,该水口在宝钢等大钢厂应用,取得了良好的使用效果。

  14. Optimization of Purge Bin Pressure in PE Unit%聚乙烯装置脱气仓压力的优化

    Institute of Scientific and Technical Information of China (English)

    刘卫东; 白鸿

    2013-01-01

      Purge bin pressure in PE unit was optimized by tuning the control loop and adjusting the filter bag. After optimization,pressure of purge bin was reduced, the degassing effect was improved,the hydrocarbon concentration of resin powder was reduced , which can make the PE plant run much more safely, and lay a foundation for the further reducing of nitrogen consumption.%  通过控制回路整定和滤袋调整优化了聚乙烯装置脱气仓的压力。优化后脱气压力降低,改善了脱气效果,降低了树脂粉末烃含量,使装置运行的安全性得到提高,为进一步降低氮气用量奠定基础。

  15. Volatile organic compounds in whole blood - determination by heated dynamic headspace purge and trap isotope-dilution GC/MS. Special report, November 1984-August 1987

    Energy Technology Data Exchange (ETDEWEB)

    Cramer, P.H.; Boggess, K.E.; Hosenfeld, J.M.

    1987-07-01

    The method described was developed for the determination of a selected list of 30 organic compounds in whole human blood. The method is a heated dynamic head-space purge and trap gas chromatographic method using mass spectrometry in the limited mass-scan mode. A whole blood sample is diluted with organic free water and the mixture fortified with isotopically labeled compounds. The mixture is subsequently heated to 50/sup 0/C while stirred, and the volatile components are purged from the mixture and collected on an adsorbent trap. The volatile compounds are thermally desorbed from the trap onto a wide-bore fused-silica capillary column. Detection of the compounds is accomplished using mass spectrometry in the limited mass-scan mode where only selected ions are scanned. Quantitation of the analytes is accomplished by using the specific ion responses from standards of the analytes and their corresponding labeled analogs or internal standards.

  16. Progress and developing trend of purging plug for refining ladle%精炼钢包用透气砖的研究进展与发展方向

    Institute of Scientific and Technical Information of China (English)

    贾全利; 吴然; 孙小改

    2013-01-01

    总结了精炼钢包用透气砖的损毁原因和现用刚玉-尖晶石透气砖在改善抗热震性方面的研究新进展;介绍了非氧化物结合刚玉质透气砖的研究结果和在精炼钢包上的使用情况,提出了透气砖的研究和发展方向.%Damage reasons of purging plug for refining ladle and research progress on thermal shock resistance of corundum-spinel purging plug were summarized. Research achievements and application results of nonoxides bonded corundum purging plug for refining ladle were reviewed. The further research and developing trend of purging plug were proposed.

  17. Games and Platform Decisions

    DEFF Research Database (Denmark)

    Hansen, Poul H. Kyvsgård; Mikkola, Juliana Hsuan

    2007-01-01

    is the application of on-line games in order to provide training for decision makers and in order to generate overview over the implications of platform decisions. However, games have to be placed in a context with other methods and we argue that a mixture of games, workshops, and simulations can provide improved...

  18. Creative Platform Learning (CPL)

    DEFF Research Database (Denmark)

    Christensen, Jonna Langeland; Hansen, Søren

    Creative Platform Learning (CPL) er en pædagogisk metode, der skaber foretagsomme og innovative elever, der kan anvende deres kreativitet til at lære nyt. Ifølge den nye skolereform skal Innovation og entreprenørskab tydeliggøres i alle fag. I CPL er det en integreret del af undervisningen...

  19. Games and Platform Decisions

    DEFF Research Database (Denmark)

    Hansen, Poul H. Kyvsgård; Mikkola, Juliana Hsuan

    2007-01-01

    is the application of on-line games in order to provide training for decision makers and in order to generate overview over the implications of platform decisions. However, games have to be placed in a context with other methods and we argue that a mixture of games, workshops, and simulations can provide improved...

  20. Determining the Henry's Law constants of THMs in seawater by means of purge-and-trap gas chromatography (PT-GC): the influence of seawater as sample matrix.

    Science.gov (United States)

    Ruiz-Bevia, Francisco; Fernandez-Torres, Maria J

    2010-01-01

    The influence of seawater salts as salting out agents on the purge-and-trap gas chromatography (PT-GC) determination of trihalomethanes (THMs) was studied. This is particularly important since seawater is chlorinated when used as a cooling agent in coastal nuclear power stations. The chlorination produces unwanted THMs as by-products. A PT-GC apparatus was used to determine the Henry's Law constant of each THM, with seawater as the sample matrix.

  1. 吹扫型火焰控制器管路模型的设计%Design of Pipeline Model of Purge Type Flame Controller

    Institute of Scientific and Technical Information of China (English)

    朱利军

    2011-01-01

    The function, connection diagram and correlation element of purge type flame controller are introduced. The pipeline model is designed and connection diagram is given.%介绍吹扫型火焰控制器的功能、接线原理图及相关器件,设计相应的管路模型,并给出接线图。

  2. Preliminary Examination of Glucagon-Like Peptide-1 Levels in Women with Purging Disorder and Bulimia Nervosa

    Science.gov (United States)

    Dossat, Amanda M.; Bodell, Lindsay P.; Williams, Diana L.; Eckel, Lisa A.; Keel, Pamela K.

    2014-01-01

    Objective This study examined pre- and post-prandial glucagon-like peptide 1 (GLP-1) levels in women with bulimia nervosa (BN), purging disorder (PD), and non-eating disorder control women to better understand whether alterations in satiation-related hormones in BN may be linked to binge-eating episodes or other altered ingestive behaviors. Method Participants included women with BN (n = 19), PD (n = 14), or controls (n = 14). Participants provided subjective ratings for hunger and fullness and plasma samples before and after consumption of a standardized test meal. Results As expected, GLP-1 levels increased significantly following test meal consumption; however, participants with BN displayed significantly lower GLP-1 levels compared to PD and control participants both before and after consumption of the test meal. There were no significant differences between PD and control participants in GLP-1 levels, but individuals with PD displayed significantly higher levels of fullness throughout the test meal as compared to both control and BN participants. Discussion Our findings provide preliminary evidence that reduced GLP-1 levels in individuals with BN may be associated with binge-eating episodes. Additionally, increased fullness in individuals with PD does not appear to be accounted for by exaggerated post-prandial GLP-1 release. PMID:24590464

  3. Comparison of purge and trap GC/MS and purgeable organic chloride analysis for monitoring volatile chlorinated hydrocarbons

    Science.gov (United States)

    Barber, Larry B.; Thurman, E. Michael; Takahashi, Yoshi; Noriega, Mary C.

    1992-01-01

    A combined field and laboratory study was conducted to compare purge and trap gas chromatography/mass spectrometry (PT-GC/MS) and purgeable organic chloride (POCl) analysis for measuring volatile chlorinated hydrocarbons (VCH) in ground water. Distilled-water spike and recovery experiments using 10 VCH indicate that at concentrations greater than 1 ??g/l recovery is more than 80 percent for both methods with relative standard deviations of about 10 percent. Ground-water samples were collected from a site on Cape Cod, Massachusetts, where a shallow unconfined aquifer has been contaminated by VCH, and were analyzed by both methods. Results for PT-GC/MS and POCl analysis of the ground-water samples were not significantly different (alpha = 0.05, paired t-test analysis) and indicated little bias between the two methods. Similar conclusions about concentrations and distributions of VCH in the ground-water contamination plume were drawn from the two data sets. However, only PT-GC/MS analysis identified the individual compounds present and determined their concentrations, which was necessary for toxicological and biogeochemical evaluation of the contaminated ground water. POCl analysis was a complimentary method for use with PT-GC/MS analysis for identifying samples with VCH concentrations below the detection limit or with high VCH concentrations that require dilution. Use of POCl as a complimentary monitoring method for PT-GC/MS can result in more efficient use of analytical resources.

  4. Influence of negative affect on decision making in women with restrictive and binge-purge type anorexia nervosa.

    Science.gov (United States)

    Danner, Unna N; Sternheim, Lot; Bijsterbosch, Jojanneke M; Dingemans, Alexandra E; Evers, Catharine; van Elburg, Annemarie A

    2016-05-30

    The present study aims to examine the influence of negative affect on decision making in women with anorexia nervosa (AN) compared to healthy control women and, secondly, to assess differences between the restrictive (ANR) and binge-purge (ANBP) subtypes. One hundred four women (32 with ANR, 32 with ANBP, and 40 healthy controls) participated. All women were asked to watch either a negative or a control film fragment, both followed by the Bechara Gambling Task (BGT). Before and after the fragments negative affect was measured. Additionally, relevant characteristics (e.g., overall depressive symptoms) were assessed. Differences in negative affect did not influence decision making performance. Independent of affective state, decision making was found to be impaired in women with ANBP (no learning effect on the BGT), but not in women with ANR. These findings highlight the importance of considering different AN subtypes when examining decision making processes. However, the role of negative affect on decision making remains uncertain. Since other affect related factors such as affect dysregulation may also play a role, future studies on decision making in AN should take the role of affect into account.

  5. In-tube extraction of volatile organic compounds from aqueous samples: an economical alternative to purge and trap enrichment.

    Science.gov (United States)

    Laaks, Jens; Jochmann, Maik A; Schilling, Beat; Schmidt, Torsten C

    2010-09-15

    A novel in-tube extraction device (ITEX 2) for headspace sampling was evaluated for GC/MS analysis of aqueous samples. Twenty compounds of regulatory and drinking water quality importance were analyzed, including halogenated hydrocarbons, BTEX compounds (benzene, toluene, ethylbenzene, xylenes), fuel oxygenates, geosmin, and 2-methylisoborneol. Five commercially available sorbent traps were compared for their compound specific extraction yield. On the basis of the results, a mixed bed trap was prepared and evaluated. The extraction parameters were optimized to yield maximum sensitivity within the time of a GC run, to avoid unnecessary downtime of the system. Method detection limits of 1-10 ng L(-1) were achieved for volatile organic compounds (VOCs), which is much lower than demands by regulatory limit values. The performance of the ITEX system is similar to that of purge and trap systems, but it requires lower sample volumes and is less prone to contamination, much simpler, more flexible, and affordable. Average relative standard deviations below 10% were achieved for all analytes, and recoveries from spiked tap water samples were between 90% and 103%, mostly. The extraction is nonexhaustive, removing a fraction of 7% to 55% of the target compounds, depending on the air-water partitioning coefficients. The method was also tested with nonsynthetic samples, including tap, pond, and reservoir water and different soft drinks.

  6. Serotonergic dysfunction across the eating disorders: relationship to eating behaviour, purging behaviour, nutritional status and general psychopathology.

    Science.gov (United States)

    Monteleone, P; Brambilla, F; Bortolotti, F; Maj, M

    2000-09-01

    Several recent studies have pointed to a dysfunction of serotonin transmission in patients with eating disorders. Notwithstanding, it is not known whether serotonergic abnormalities are related primarily to eating and/or purging behaviour, nutritional status or general psychopathological dimensions. Therefore, by using a validated neuroendocrine strategy, we investigated central serotonergic function in patients with anorexia nervosa, bulimia nervosa or binge-eating disorder who differ on the above parameters. Plasma prolactin response to D-fenfluramine (30 mg p.o.) or placebo was measured in 58 drug-free female volunteers, comprising 15 underweight anorexic women, 18 bulimic women, 10 women with binge-eating disorder and 15 female healthy controls. Behavioural assessment included ratings of eating disorder symptoms, depression, aggression and food-related obsessions and compulsions. A significantly decreased prolactin response to D-fenfluramine was found in underweight anorexic women and in bulimics with high frequency bingeing ( > 2 binge episodes/day), but not in patients with binge-eating disorder or in bulimics with low frequency bingeing (nervosa. Moreover, they show, for the first time, that the hypothalamic serotonergic system is not altered in women with binge-eating disorder.

  7. Empirically defining rapid response to intensive treatment to maximize prognostic utility for bulimia nervosa and purging disorder.

    Science.gov (United States)

    MacDonald, Danielle E; Trottier, Kathryn; McFarlane, Traci; Olmsted, Marion P

    2015-05-01

    Rapid response (RR) to eating disorder treatment has been reliably identified as a predictor of post-treatment and sustained remission, but its definition has varied widely. Although signal detection methods have been used to empirically define RR thresholds in outpatient settings, RR to intensive treatment has not been investigated. This study investigated the optimal definition of RR to day hospital treatment for bulimia nervosa and purging disorder. Participants were 158 patients who completed ≥6 weeks of day hospital treatment. Receiver operating characteristic (ROC) analysis was used to create four definitions of RR that could differentiate between remission and nonremission at the end of treatment. Definitions were based on binge/vomit episode frequency or percent reduction from pre-treatment, during either the first four or first two weeks of treatment. All definitions were associated with higher remission rates in rapid compared to nonrapid responders. Only one definition (i.e., ≤3 episodes in the first four weeks of treatment) predicted sustained remission (versus relapse) at 6- and 12-month follow-up. These findings provide an empirically derived definition of RR to intensive eating disorder treatment, and provide further evidence that early change is an important prognostic indicator. Copyright © 2015 Elsevier Ltd. All rights reserved.

  8. The loss of essential oil components induced by the Purge Time in the Pressurized Liquid Extraction (PLE) procedure of Cupressus sempervirens.

    Science.gov (United States)

    Dawidowicz, Andrzej L; Czapczyńska, Natalia B; Wianowska, Dorota

    2012-05-30

    The influence of different Purge Times on the effectiveness of Pressurized Liquid Extraction (PLE) of volatile oil components from cypress plant matrix (Cupressus sempervirens) was investigated, applying solvents of diverse extraction efficiencies. The obtained results show the decrease of the mass yields of essential oil components as a result of increased Purge Time. The loss of extracted components depends on the extrahent type - the greatest mass yield loss occurred in the case of non-polar solvents, whereas the smallest was found in polar extracts. Comparisons of the PLE method with Sea Sand Disruption Method (SSDM), Matrix Solid-Phase Dispersion Method (MSPD) and Steam Distillation (SD) were performed to assess the method's accuracy. Independent of the solvent and Purge Time applied in the PLE process, the total mass yield was lower than the one obtained for simple, short and relatively cheap low-temperature matrix disruption procedures - MSPD and SSDM. Thus, in the case of volatile oils analysis, the application of these methods is advisable.

  9. Report on the analysis of common beverages spiked with gamma-hydroxybutyric acid (GHB) and gamma-butyrolactone (GBL) using NMR and the PURGE solvent-suppression technique.

    Science.gov (United States)

    Lesar, Casey T; Decatur, John; Lukasiewicz, Elaan; Champeil, Elise

    2011-10-10

    In forensic evidence, the identification and quantitation of gamma-hydroxybutyric acid (GHB) in "spiked" beverages is challenging. In this report, we present the analysis of common alcoholic beverages found in clubs and bars spiked with gamma-hydroxybutyric acid (GHB) and gamma-butyrolactone (GBL). Our analysis of the spiked beverages consisted of using (1)H NMR with a water suppression method called Presaturation Utilizing Relaxation Gradients and Echoes (PURGE). The following beverages were analyzed: water, 10% ethanol in water, vodka-cranberry juice, rum and coke, gin and tonic, whisky and diet coke, white wine, red wine, and beer. The PURGE method allowed for the direct identification and quantitation of both compounds in all beverages except red and white wine where small interferences prevented accurate quantitation. The NMR method presented in this paper utilizes PURGE water suppression. Thanks to the use of a capillary internal standard, the method is fast, non-destructive, sensitive and requires no sample preparation which could disrupt the equilibrium between GHB and GBL.

  10. Epistatic interactions involving DRD2, DRD4, and COMT polymorphisms and risk of substance abuse in women with binge-purge eating disturbances.

    Science.gov (United States)

    Steiger, Howard; Thaler, Lea; Gauvin, Lise; Joober, Ridha; Labbe, Aurelie; Israel, Mimi; Kucer, Audrey

    2016-06-01

    Substance abuse is common in individuals with bulimia-spectrum (binge-purge) eating disturbances, a co-occurrence that has been attributed to shared neurobiological substrates--notably alterations in dopaminergic activity. We examined the implications of variations of selected, dopamine-relevant polymorphisms (DRD2 Taq1A, DRD4 7R, and COMT) for risk of substance abuse in women with binge-purge eating syndromes. We genotyped 183 women (66.1% showing full-threshold BN and 33.9% showing sub-syndromic variants), and assessed lifetime presence of alcohol, cannabis, cocaine, and stimulant abuse or dependence using structured interviews. Tests for main and interaction effects of various allele combinations revealed that individuals who carried high function COMT and low-function DRD4 7R alleles (a combination expected to be associated with higher risk) did indeed show more lifetime substance abuse and, specifically, more cannabis abuse. Our findings suggest that a gene combination that, in theory, codes for low levels of dopaminergic neurotransmission coincides with sensitivity to substance abuse in a sample displaying binge-purge eating-disorder variants.

  11. Purge gas recovery of ammonia synthesis plant by integrated configuration of catalytic hydrogen-permselective membrane reactor and solid oxide fuel cell as a novel technology

    Science.gov (United States)

    Siavashi, Fakhteh; Saidi, Majid; Rahimpour, Mohammad Reza

    2014-12-01

    The purge gas emission of ammonia synthesis plant which contains hazardous components is one of the major sources of environmental pollution. Using integrated configuration of catalytic hydrogen-permselective membrane reactor and solid oxide fuel cell (SOFC) system is a new approach which has a great impact to reduce the pollutant emission. By application of this method, not only emission of ammonia and methane in the atmosphere is prevented, hydrogen is produced through the methane steam reforming and ammonia decomposition reactions that take place simultaneously in a catalytic membrane reactor. The pure generated hydrogen by recovery of the purge gas in the Pd-Ag membrane reactor is used as a feed of SOFC. Since water is the only byproduct of the electrochemical reaction in the SOFC, it is recycled to the reactor for providing the required water of the reforming reaction. Performance investigation of the reactor represents that the rate of hydrogen permeation increases with enhancing the reactor temperature and pressure. Also modeling results indicate that the SOFC performance improves with increasing the temperature and fuel utilization ratio. The generated power by recovery of the purging gas stream of ammonia synthesis plant in the Razi petrochemical complex is about 8 MW.

  12. Mobile Platforms and Development Environments

    CERN Document Server

    Helal, Sumi; Li, Wengdong

    2012-01-01

    Mobile platform development has lately become a technological war zone with extremely dynamic and fluid movement, especially in the smart phone and tablet market space. This Synthesis lecture is a guide to the latest developments of the key mobile platforms that are shaping the mobile platform industry. The book covers the three currently dominant native platforms -- iOS, Android and Windows Phone -- along with the device-agnostic HTML5 mobile web platform. The lecture also covers location-based services (LBS) which can be considered as a platform in its own right. The lecture utilizes a sampl

  13. OPTIMIZATIONS FOR 5-AMINOLEVULINIC ACID BASED PHOTODYNAMIC THERAPY IN PURGING LEUKEMIA CELL HL60

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    Objective To optimize experimental parameters for the photosensitization of 5-aminolevulinic acid (ALA) in promyelocytic leukemia cell HL60 and compare them with normal human peripheral blood mononuclear cell (PBMC). Methods ALA incubation time, wavelength applied to irradiate, concentration of ALA incubated, irradiation fluence may modulate the effect of 5-aminolevulinic acid based Photodynamic Therapy (ALA-PDT).The high-pressure mercury lamps of 400W served as light source, the interference filter of 410nm, 432nm, 545nm, 577nm were used to select the specific wavelength. Fluorescence microscope was used to detect the fluorescence intensity and location of protoporphyrin IX (PpIX) endogenously produced by ALA. MTT assay was used to measure the survival of cell. Flow cytometry with ANNEXIN V FITC kit (contains annexin V FITC, binding buffer and PI) was used to detect the mode of cell death. Results ① 1mmol/L ALA incubated 1×105/mL HL60 cell line for 4 hours, the maximum fluorescence of ALA induced PpIX was detected in cytomembrane. ② Irradiated with 410nm for 14.4J/cm2 can result in the minimum survivability of HL60 cell. ③ The main mode of HL60 cell death caused by ALA-PDT is necrosis. Conclusion ALA for 1mmol/L, 4 hours for dark incubation time, 410nm for irradiation wavelength, 14.4J/cm2 for irradiation fluence were the optimal parameters to selectively eliminate promyelocytic leukemia cell HL60 by ALA based PDT. The photosensitization of ALA based PDT caused the necrosis of HL60 cell, so it could be used for inactivation of certain leukemia cells.

  14. Vertical Wave Impacts on Offshore Wind Turbine Inspection Platforms

    OpenAIRE

    Bredmose, Henrik; Jacobsen, Niels Gjøl

    2011-01-01

    Breaking wave impacts on a monopile at 20 m depth are computed with a VOF (Volume Of Fluid) method. The impacting waves are generated by the second-order focused wave group technique, to obtain waves that break at the position of the monopile. The subsequent impact from the vertical run-up flow on a horizontal inspection platform is computed for five different platform levels. The computational results show details of monopile impact such as slamming pressures from the overturning wave front ...

  15. Online stock trading platform

    Directory of Open Access Journals (Sweden)

    Ion LUNGU

    2006-01-01

    Full Text Available The Internet is the perfect tool that can assure the market’s transparency for any user who wants to trade on the stock market. The investor can have access to the market news, financial calendar or the press releases of the issuers. A good online trading platform also provides real-time intraday quotes, trading history and technical analysis giving the investor a clearer view of the supply and demand in the market. All this information provides the investor a good image of the market and encourages him to trade. This paper wishes to draft the pieces of an online trading platform and to analyze the impact of developing and implementing one in a brokerage firm.

  16. Available: motorised platform

    CERN Document Server

    The COMPASS collaboration

    2014-01-01

    The COMPASS collaboration would like to offer to a new owner the following useful and fully operational piece of equipment, which is due to be replaced with better adapted equipment.   Please contact Erwin Bielert (erwin.bielert@cern.ch or 160539) for further information.  Motorized platform (FOR FREE):   Fabricated by ACL (Alfredo Cardoso & Cia Ltd) in Portugal. The model number is MeXs 5-­‐30.  Specifications: 5 m wide, 1 m deep, adjustable height (1.5 m if folded). Maximum working floor height: 4 m. conforms to CERN regulations, number LV158. Type LD500, capacity 500 kg and weight 2000 kg.  If no interested party is found before December 2014, the platform will be thrown away.

  17. Common tester platform concept.

    Energy Technology Data Exchange (ETDEWEB)

    Hurst, Michael James

    2008-05-01

    This report summarizes the results of a case study on the doctrine of a common tester platform, a concept of a standardized platform that can be applicable across the broad spectrum of testing requirements throughout the various stages of a weapons program, as well as across the various weapons programs. The common tester concept strives to define an affordable, next-generation design that will meet testing requirements with the flexibility to grow and expand; supporting the initial development stages of a weapons program through to the final production and surveillance stages. This report discusses a concept investing key leveraging technologies and operational concepts combined with prototype tester-development experiences and practical lessons learned gleaned from past weapons programs.

  18. OGC Collaborative Platform undercover

    Science.gov (United States)

    Buehler, G.; Arctur, D. K.; Bermudez, L. E.

    2012-12-01

    The mission of the Open Geospatial Consortium (OGC) is to serve as a global forum for the collaboration of developers and users of spatial data products and services, and to advance the development of international standards for geospatial interoperability. The OGC coordinates with over 400 institutions in the development of geospatial standards. OGC has a dedicated staff supported by a Collaborative Web Platform to enable sophisticated and successful coordination among its members. Since its origins in the early 1990s, the OGC Collaborative Web Platform has evolved organically to be the collaboration hub for standards development in the exchange of geospatial and related types of information, among a global network of thousands of technical, scientific and management professionals spanning numerous disparate application domains. This presentation describes the structure of this collaboration hub, the relationships enabled (both among and beyond OGC members), and how this network fits in a broader ecosystem of technology development and information standards organizations.

  19. Video analysis platform

    OpenAIRE

    FLORES, Pablo; Arias, Pablo; Lecumberry, Federico; Pardo, Álvaro

    2006-01-01

    In this article we present the Video Analysis Platform (VAP) which is an open source software framework for video analysis, processing and description. The main goals of VAP are: to provide a multiplatform system which allows the easy implementation of video algorithms, provide structures and algorithms for the segmentation of video data in its different levels of abstraction: shots, frames, objects, regions, etc, permit the generation and comparison of MPEG7-like descriptors, and develop tes...

  20. Cloud Robotics Platforms

    Directory of Open Access Journals (Sweden)

    Busra Koken

    2015-01-01

    Full Text Available Cloud robotics is a rapidly evolving field that allows robots to offload computation-intensive and storage-intensive jobs into the cloud. Robots are limited in terms of computational capacity, memory and storage. Cloud provides unlimited computation power, memory, storage and especially collaboration opportunity. Cloud-enabled robots are divided into two categories as standalone and networked robots. This article surveys cloud robotic platforms, standalone and networked robotic works such as grasping, simultaneous localization and mapping (SLAM and monitoring.

  1. HPC - Platforms Penta Chart

    Energy Technology Data Exchange (ETDEWEB)

    Trujillo, Angelina Michelle [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2015-10-08

    Strategy, Planning, Acquiring- very large scale computing platforms come and go and planning for immensely scalable machines often precedes actual procurement by 3 years. Procurement can be another year or more. Integration- After Acquisition, machines must be integrated into the computing environments at LANL. Connection to scalable storage via large scale storage networking, assuring correct and secure operations. Management and Utilization – Ongoing operations, maintenance, and trouble shooting of the hardware and systems software at massive scale is required.

  2. Study of Piezoresistive Micro Electro-Mechanical Accelerometer Design Platform

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    According to the inland micro electro-mechanical system (MEMS) process technique level, a design platform of piezoresistive micro electro-mechanical accelerometer is given. This platform is much more adaptable to the inland designer compared with the current MEMS CAD software. The design flow is presented in detail, and the key techique in the platform is analyzed amply. The structure design methodology is exemplified in the design of a piezoresistive accelerometer, and the accelerometer is the optimized structure for the given performance requirements. The accelerometer is now being manufactured.

  3. IP Rights and Technological Platforms

    OpenAIRE

    Robert P. Merges

    2008-01-01

    This paper is about intellectual property rights (IPRs) and platform technologies. After a brief introduction explaining some basics of networks, standards and platforms, I turn to three policy issues. The first is the role of IP in what might be termed platform policies, the decisions by courts and regulators concerning whether and how to promote multi-party access to important digital platforms such as media player hardware, cell phones, PCs, and the like. I argue that for the most part the...

  4. "Platform switching": Serendipity

    Directory of Open Access Journals (Sweden)

    N Kalavathy

    2014-01-01

    Full Text Available Implant dentistry is the latest developing field in terms of clinical techniques, research, material science and oral rehabilitation. Extensive work is being done to improve the designing of implants in order to achieve better esthetics and function. The main drawback with respect to implant restoration is achieving good osseointegration along with satisfactory stress distribution, which in turn will improve the prognosis of implant prosthesis by reducing the crestal bone loss. Many concepts have been developed with reference to surface coating of implants, surgical techniques for implant placement, immediate and delayed loading, platform switching concept, etc. This article has made an attempt to review the concept of platform switching was in fact revealed accidentally due to the nonavailability of the abutment appropriate to the size of the implant placed. A few aspect of platform switching, an upcoming idea to reduce crestal bone loss have been covered. The various methods used for locating and preparing the data were done through textbooks, Google search and related articles.

  5. "Platform switching": serendipity.

    Science.gov (United States)

    Kalavathy, N; Sridevi, J; Gehlot, Roshni; Kumar, Santosh

    2014-01-01

    Implant dentistry is the latest developing field in terms of clinical techniques, research, material science and oral rehabilitation. Extensive work is being done to improve the designing of implants in order to achieve better esthetics and function. The main drawback with respect to implant restoration is achieving good osseointegration along with satisfactory stress distribution, which in turn will improve the prognosis of implant prosthesis by reducing the crestal bone loss. Many concepts have been developed with reference to surface coating of implants, surgical techniques for implant placement, immediate and delayed loading, platform switching concept, etc. This article has made an attempt to review the concept of platform switching was in fact revealed accidentally due to the nonavailability of the abutment appropriate to the size of the implant placed. A few aspect of platform switching, an upcoming idea to reduce crestal bone loss have been covered. The various methods used for locating and preparing the data were done through textbooks, Google search and related articles.

  6. The Prodiguer Messaging Platform

    Science.gov (United States)

    Denvil, S.; Greenslade, M. A.; Carenton, N.; Levavasseur, G.; Raciazek, J.

    2015-12-01

    CONVERGENCE is a French multi-partner national project designed to gather HPC and informatics expertise to innovate in the context of running French global climate models with differing grids and at differing resolutions. Efficient and reliable execution of these models and the management and dissemination of model output are some of the complexities that CONVERGENCE aims to resolve.At any one moment in time, researchers affiliated with the Institut Pierre Simon Laplace (IPSL) climate modeling group, are running hundreds of global climate simulations. These simulations execute upon a heterogeneous set of French High Performance Computing (HPC) environments. The IPSL's simulation execution runtime libIGCM (library for IPSL Global Climate Modeling group) has recently been enhanced so as to support hitherto impossible realtime use cases such as simulation monitoring, data publication, metrics collection, simulation control, visualizations … etc. At the core of this enhancement is Prodiguer: an AMQP (Advanced Message Queue Protocol) based event driven asynchronous distributed messaging platform. libIGCM now dispatches copious amounts of information, in the form of messages, to the platform for remote processing by Prodiguer software agents at IPSL servers in Paris. Such processing takes several forms: Persisting message content to database(s); Launching rollback jobs upon simulation failure; Notifying downstream applications; Automation of visualization pipelines; We will describe and/or demonstrate the platform's: Technical implementation; Inherent ease of scalability; Inherent adaptiveness in respect to supervising simulations; Web portal receiving simulation notifications in realtime.

  7. Platform computing powers enterprise grid

    CERN Multimedia

    2002-01-01

    Platform Computing, today announced that the Stanford Linear Accelerator Center is using Platform LSF 5, to carry out groundbreaking research into the origins of the universe. Platform LSF 5 will deliver the mammoth computing power that SLAC's Linear Accelerator needs to process the data associated with intense high-energy physics research (1 page).

  8. Collapse of modern carbonate platform margins

    Energy Technology Data Exchange (ETDEWEB)

    Mullins, H.T.; Hine, A.C.; Gardulski, A.

    1985-01-01

    Modern carbonate platform margins in the Florida-Bahama region have been viewed as depositional or constructional features. However, recent studies have shown that carbonate escarpments, such as the Blake-Bahama and West Florida Escarpments, are erosional in origin where the platform margins have a scalloped or horse-shoe shape. Seismic reflection data from one of these crescentic features along the west Florida platform margin indicate that it originated by large scale gravity collapse (slump). This collapse structure extends for at least 120 km along the margin and has removed about 350 m of strata as young as early Neogene. Although at least three generations of slope failure are recognized, catastrophic collapse appears to have occurred in the mid-Miocene. Gravitational instability due to high rates of sediment accumulation may have been the triggering mechanism. These data suggest that submarine slumping is an important process in the retreat of limestone escarpments and in the generation of carbonate megabreccia debris flows. Scalloped platform margins occur on satellite images of northern Exuma Sound and Columbus Basin in the Bahamas. The authors suggest that large-scale submarine slumping can cause elongation of structurally controlled intraplatform basins (Exuma South), and produce anomalous horse-shoe shaped basins (Columbus Basin) by mega-collapse processes.

  9. Predicting Droplet Formation on Centrifugal Microfluidic Platforms

    Science.gov (United States)

    Moebius, Jacob Alfred

    Centrifugal microfluidics is a widely known research tool for biological sample and water quality analysis. Currently, the standard equipment used for such diagnostic applications include slow, bulky machines controlled by multiple operators. These machines can be condensed into a smaller, faster benchtop sample-to-answer system. Sample processing is an important step taken to extract, isolate, and convert biological factors, such as nucleic acids or proteins, from a raw sample to an analyzable solution. Volume definition is one such step. The focus of this thesis is the development of a model predicting monodispersed droplet formation and the application of droplets as a technique for volume definition. First, a background of droplet microfluidic platforms is presented, along with current biological analysis technologies and the advantages of integrating such technologies onto microfluidic platforms. Second, background and theories of centrifugal microfluidics is given, followed by theories relevant to droplet emulsions. Third, fabrication techniques for centrifugal microfluidic designs are discussed. Finally, the development of a model for predicting droplet formation on the centrifugal microfluidic platform are presented for the rest of the thesis. Predicting droplet formation analytically based on the volumetric flow rates of the continuous and dispersed phases, the ratios of these two flow rates, and the interfacial tension between the continuous and dispersed phases presented many challenges, which will be discussed in this work. Experimental validation was completed using continuous phase solutions of different interfacial tensions. To conclude, prospective applications are discussed with expected challenges.

  10. Dialectical behavior therapy for adolescent binge eating, purging, suicidal behavior, and non-suicidal self-injury: a pilot study.

    Science.gov (United States)

    Fischer, Sarah; Peterson, Claire

    2015-03-01

    There are few published randomized controlled trials examining treatment for symptoms of bulimia nervosa (BN) in adolescents. Additionally, many adolescents presenting for treatment for BN symptoms endorse co-occurring mood disturbances, suicidality, and nonsuicidal self-injury (NSSI), and may not meet full Diagnostic and Statistical Manual-IV-Text Revision (DSM-IV-TR) diagnostic criteria for BN. In addition to the limited number of randomized controlled trials, published treatment studies of BN symptoms in adolescence do not specifically address the multiple comorbid symptoms that these adolescents often report. The purpose of this pilot study was to examine the feasibility and effectiveness of an outpatient dialectical behavior therapy (DBT) program for adolescents with symptoms of BN, suicide attempts, and NSSI. Ten eligible participants enrolled in the study; 3 dropped within 4 weeks of initiating treatment. In addition to binge eating and suicidal behavior, participants also endorsed a number of other comorbid mood disorders and substance abuse. Seven participants completed 6 months of treatment and 6-month follow-up assessments. Treatment included access to a crisis management system, individual therapy, skills training, and a therapist consultation team. At posttreatment, participants had significantly reduced self-harm; (Cohen's d = 1.35), frequency of objective binge episodes (Cohen's d = .46), frequency of purging (Cohen's d = .66), and Global Eating Disorder Examination scores (Cohen's d = .64). At follow-up, 6 participants were abstinent of NSSI; 3 participants were abstinent from binge eating. At follow-up, treatment gains were maintained and enhanced. Results indicate that it is feasible to address multiple forms of psychopathology during the treatment of BN symptoms in this age-group.

  11. Distribution characteristics of volatile methylsiloxanes in Tokyo Bay watershed in Japan: Analysis of surface waters by purge and trap method.

    Science.gov (United States)

    Horii, Yuichi; Minomo, Kotaro; Ohtsuka, Nobutoshi; Motegi, Mamoru; Nojiri, Kiyoshi; Kannan, Kurunthachalam

    2017-05-15

    Surface waters including river water and effluent from sewage treatment plants (STPs) were collected from Tokyo Bay watershed, Japan, and analyzed for seven cyclic and linear volatile methylsiloxanes (VMSs), i.e., D3, D4, D5, D6, L3, L4, and L5 by an optimized purge and trap extraction method. The total concentrations of seven VMSs (ΣVMS) in river water ranged from <4.9 to 1700ng/L (mean: 220ng/L). The individual mean concentrations of cyclic VMSs in surface waters were; 10ng/L for D3, 13ng/L for D4, 180ng/L for D5, and 18ng/L for D6. The concentrations of ΣVMS determined in STP effluents varied widely from 99 to 2500ng/L and the individual mean concentrations were 21ng/L for D3, 27ng/L for D4, 540ng/L for D5, and 45ng/L for D6. D5, which is widely used in personal-care products, was found to be the most abundant compound in both river water and STP effluent. Linear VMSs were detected at much lower frequency and concentrations than those of cyclic VMSs. The measured concentrations of D4 were below the no-observed effect concentration (NOEC). The annual emission of ΣVMS through STPs into Tokyo Bay watershed was estimated at 2300kg. Our results indicate widespread distribution of VMSs in Tokyo Bay watershed and the influence of domestic wastewater discharges as a source of VMSs in the aquatic environment.

  12. Anxiety and compulsion patterns in the maintenance of bingeing/purging behaviours by individuals with bulimia nervosa.

    Science.gov (United States)

    Thomas, M; Lovell, A

    2015-02-01

    Bulimia nervosa, if not treated or if treated unsuccessfully, can develop into a severe and enduring eating disorder. Analysis of self-management of Seed-BN indicates that individuals frequently experience significant negative mental health issues and a complex relationship with medication management. Two discrete patterns of coping strategies to prevent deterioration in distressing symptoms were in evidence, controlled vomiting, which was related to the management of anxiety, and uncontrolled vomiting due to more dominant self-management of compulsive acts. The implications for nursing revolve around accurate assessment of vomiting and subsequent engagement by the individual with their coping strategies in relation to perceived deterioration in distressing symptoms. This paper reports on the results of a study into the self-reported coping strategies employed by a small sample (n = 12) of individuals diagnosed with bulimia nervosa purging sub-type, severe and enduring eating disorder (Seed-BN), referred to an outpatient clinic for psychotherapy. Data collection focused on the vomiting activities of participants through analysis of their self-management from diary extracts, which recorded vomiting patterns. Participants all experienced significant mental health issues, had complex histories of BN over a prolonged period, difficulties maintaining relationships, and many had an additional history of substance misuse including dependence on prescription drugs. The study findings indicated two different self-management strategies, anxiety containment and compulsion maintenance. There was a clear association between anxiety and controlled weekly vomiting patterns compared with compulsion and daily vomiting patterns. The implications for nursing practice relate to the potential for assessment of differences in vomiting patterns to indicate self-management status and subsequent interventions focusing on either anxiety or compulsive patterns. © 2014 John Wiley & Sons Ltd.

  13. Gas Flow Detection System

    Science.gov (United States)

    Moss, Thomas; Ihlefeld, Curtis; Slack, Barry

    2010-01-01

    This system provides a portable means to detect gas flow through a thin-walled tube without breaking into the tubing system. The flow detection system was specifically designed to detect flow through two parallel branches of a manifold with only one inlet and outlet, and is a means for verifying a space shuttle program requirement that saves time and reduces the risk of flight hardware damage compared to the current means of requirement verification. The prototype Purge Vent and Drain Window Cavity Conditioning System (PVD WCCS) Flow Detection System consists of a heater and a temperature-sensing thermistor attached to a piece of Velcro to be attached to each branch of a WCCS manifold for the duration of the requirement verification test. The heaters and thermistors are connected to a shielded cable and then to an electronics enclosure, which contains the power supplies, relays, and circuit board to provide power, signal conditioning, and control. The electronics enclosure is then connected to a commercial data acquisition box to provide analog to digital conversion as well as digital control. This data acquisition box is then connected to a commercial laptop running a custom application created using National Instruments LabVIEW. The operation of the PVD WCCS Flow Detection System consists of first attaching a heater/thermistor assembly to each of the two branches of one manifold while there is no flow through the manifold. Next, the software application running on the laptop is used to turn on the heaters and to monitor the manifold branch temperatures. When the system has reached thermal equilibrium, the software application s graphical user interface (GUI) will indicate that the branch temperatures are stable. The operator can then physically open the flow control valve to initiate the test flow of gaseous nitrogen (GN2) through the manifold. Next, the software user interface will be monitored for stable temperature indications when the system is again at

  14. Virtual interconnection platform initiative scoping study

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Yong [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Kou, Gefei [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Pan, Zuohong [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Liu, Yilu [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); King Jr., Thomas J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2016-01-01

    Due to security and liability concerns, the research community has limited access to realistic large-scale power grid models to test and validate new operation and control methodologies. It is also difficult for industry to evaluate the relative value of competing new tools without a common platform for comparison. This report proposes to develop a large-scale virtual power grid model that retains basic features and represents future trends of major U.S. electric interconnections. This model will include realistic power flow and dynamics information as well as a relevant geospatial distribution of assets. This model will be made widely available to the research community for various power system stability and control studies and can be used as a common platform for comparing the efficacies of various new technologies.

  15. The Geohazards Exploitation Platform

    Science.gov (United States)

    Laur, Henri; Casu, Francesco; Bally, Philippe; Caumont, Hervé; Pinto, Salvatore

    2016-04-01

    The Geohazards Exploitation Platform, or Geohazards TEP (GEP), is an ESA originated R&D activity of the EO ground segment to demonstrate the benefit of new technologies for large scale processing of EO data. This encompasses on-demand processing for specific user needs, systematic processing to address common information needs of the geohazards community, and integration of newly developed processors for scientists and other expert users. The platform supports the geohazards community's objectives as defined in the context of the International Forum on Satellite EO and Geohazards organised by ESA and GEO in Santorini in 2012. The GEP is a follow on to the Supersites Exploitation Platform (SSEP) an ESA initiative to support the Geohazards Supersites & Natural Laboratories initiative (GSNL). Today the GEP allows to exploit 70+ Terabyte of ERS and ENVISAT archive and the Copernicus Sentinel-1 data available on line. The platform has already engaged 22 European early adopters in a validation activity initiated in March 2015. Since September, this validation has reached 29 single user projects. Each project is concerned with either integrating an application, running on demand processing or systematically generating a product collection using an application available in the platform. The users primarily include 15 geoscience centres and universities based in Europe: British Geological Survey (UK), University of Leeds (UK), University College London (UK), ETH University of Zurich (CH), INGV (IT), CNR-IREA and CNR-IRPI (IT), University of L'Aquila (IT), NOA (GR), Univ. Blaise Pascal & CNRS (FR), Ecole Normale Supérieure (FR), ISTERRE / University of Grenoble-Alpes (FR). In addition, there are users from Africa and North America with the University of Rabat (MA) and the University of Miami (US). Furthermore two space agencies and four private companies are involved: the German Space Research Centre DLR (DE), the European Space Agency (ESA), Altamira Information (ES

  16. Gram–Schmidt Process in Different Parallel Platforms

    Directory of Open Access Journals (Sweden)

    Genci Berati

    2015-06-01

    Full Text Available Important operations in numerical computing are vector orthogonalization. One of the well-known algorithms for vector orthogonalisation is Gram–Schmidt algorithm. This is a method for constructing a set of orthogonal vectors in an inner product space, most commonly the Euclidean space Rn. This process takes a finite, linearly independent set S = {b1, b2, …, bk} vectors for k = n and generates an orthogonal set S1 = {o1, o2, …, ok}. Like the most of the dense operations and big data processing problems, the Gram–Schmidt process steps can be performed by using parallel algorithms and can be implemented in parallel programming platforms. The parallelized algorithm is dependent to the platform used and needs to be adapted for the optimum performance for each parallel platform. The paper shows the algorithms and the implementation process of the Gram –Schmidt vector orthogonalosation in three different parallel platforms. The three platforms are: a control flow shared memory hardware systems with OpenMP, b control flow distributed memory hardware systems with MPI and c dataflow architecture systems using Maxeler Data Flow Engines hardware. Using as single running example a parallel implementation of the computation of the Gram –Schmidt vector orthogonalosation, this paper describes how the fundamentals of parallel programming, are dealt in these platforms. The paper puts into evidence the Maxeler implementation of the Gram–Schmidt algorithms compare to the traditional platforms. Paper treats the speedup and the overall performance of the three platforms versus sequential execution for 50-dimensional Euclidian space.

  17. Identification of platform levels

    DEFF Research Database (Denmark)

    Mortensen, Niels Henrik

    2005-01-01

    reduction, ability to launch a wider product portfolio without increasing resources and reduction of complexity within the whole company. To support the multiple product development process, platform based product development has in many companies such as Philips, VW, Ford etc. proven to be a very effective...... and efficient tool. Transforming product development from single to multiple product development is a significant change in product development often involving major changes of product models, procedures and organization. In the area of product models a set of new models has to be introduced, e.g. models...

  18. Conductas purgativas y estado nutricional en anorexia nerviosa y bulimia nerviosa Purging behaviours and nutritional status in anorexia nervosa and bulimia nervosa

    Directory of Open Access Journals (Sweden)

    F. J. Vaz

    2003-10-01

    patients (63.0% fulfilled the DSMIV diagnostic criteria for BN (90 purging type, 26 nonpurging type. Sixty eight patients (37.0% fulfilled the DSM-IV criteria for the diagnosis of AN (48 restricting type, 20 binging-purging type. Methods: The asessment process included anthropometry (body circumferences and skinfold thickness and body impedance analysis. Results: The two subgroups of AN patients significantly differed from each of the BN subgroups. From a nutritional point of view, some significant differences between the two DSM-IV subtypes of AN existed, but not between the purging type and the nonpurging type of BN. Conclusions: The paper discusses the clinical significance of these findings. An alternative subtypification of AN patients is proposed: 1 restricting type [patients who control their food intake and do not purge]; 2 purging type [patient with true episodes of binging which are followed by purgative behaviors]; and 3 pseudopurging type [patients with subjective binging episodes who use purging methods].

  19. Cots Correlator Platform

    Science.gov (United States)

    Schaaf, Kjeld; Overeem, Ruud

    2004-06-01

    Moore’s law is best exploited by using consumer market hardware. In particular, the gaming industry pushes the limit of processor performance thus reducing the cost per raw flop even faster than Moore’s law predicts. Next to the cost benefits of Common-Of-The-Shelf (COTS) processing resources, there is a rapidly growing experience pool in cluster based processing. The typical Beowulf cluster of PC’s supercomputers are well known. Multiple examples exists of specialised cluster computers based on more advanced server nodes or even gaming stations. All these cluster machines build upon the same knowledge about cluster software management, scheduling, middleware libraries and mathematical libraries. In this study, we have integrated COTS processing resources and cluster nodes into a very high performance processing platform suitable for streaming data applications, in particular to implement a correlator. The required processing power for the correlator in modern radio telescopes is in the range of the larger supercomputers, which motivates the usage of supercomputer technology. Raw processing power is provided by graphical processors and is combined with an Infiniband host bus adapter with integrated data stream handling logic. With this processing platform a scalable correlator can be built with continuously growing processing power at consumer market prices.

  20. Flow development through HP & LP turbines, Part II: Effects of the hub endwall secondary sealing air flow on the turbine's mainstream flow

    Science.gov (United States)

    Hu, Jialin; Du, Qiang; Liu, Jun; Wang, Pei; Liu, Guang; Liu, Hongrui; Du, Meimei

    2017-08-01

    Although many literatures have been focused on the underneath flow and loss mechanism, very few experiments and simulations have been done under the engines' representative working conditions or considering the real cavity structure as a whole. This paper aims at realizing the goal of design of efficient turbine and scrutinizing the velocity distribution in the vicinity of the rim seal. With the aid of numerical method, a numerical model describing the flow pattern both in the purge flow spot and within the mainstream flow path is established, fluid migration and its accompanied flow mechanism within the realistic cavity structure (with rim seal structure and considering mainstream & secondary air flow's interaction) is used to evaluate both the flow pattern and the underneath flow mechanism within the inward rotating cavity. Meanwhile, the underneath flow and loss mechanism are also studied in the current paper. The computational results show that the sealing air flow's ingestion and ejection are highly interwound with each other in both upstream and downstream flow of the rim seal. Both the down-stream blades' potential effects as well as the upstream blades' wake trajectory can bring about the ingestion of the hot gas flow within the cavity, abrupt increase of the static pressure is believed to be the main reason. Also, the results indicate that sealing air flow ejected through the rear cavity will cause unexpected loss near the outlet section of the blades in the downstream of the HP rotor passages.

  1. LNG接收站工艺管道试压、吹扫%LNG receiving station process piping pressure test and purging

    Institute of Scientific and Technical Information of China (English)

    张华伟; 仇德朋; 鹿晓斌; 曲顺利

    2014-01-01

    LNG receiving station process piping pressure test and purging is the final inspection of construction quality before project put into operation, to ensure that project smoothly has the vital significance. In view of the LNG clean and low temperature properties, pressure test after the pipe cleaner and dry degree is particularly important, the terminal piping pressure test use hydraulic or pneumatic according to the difference of the pressure or medium..This paper introduces the pipeline pressure test, purging process and matters needing attention, to the future of LNG receiving station test, purging process has a certain reference significance.%LNG接收站工艺管道试压、吹扫是工程投运前对施工质量的最终检验,对确保工程顺利投产具有重要的意义。鉴于LNG清洁及低温特性,试压后管道内的清洁度及干燥度显得尤为重要,目前接收站压力试验根据管道压力、介质的不同通常采用水压或气压。本文介绍了LNG工艺管道试压吹扫的方法、流程和注意事项等,对今后的LNG接收站试压、吹扫具有一定的借鉴意义。

  2. Improved outcome for high-risk acute myeloid leukemia patients using autologous bone marrow transplantation and monoclonal antibody-purged bone marrow.

    Science.gov (United States)

    Selvaggi, K J; Wilson, J W; Mills, L E; Cornwell, G G; Hurd, D; Dodge, W; Gingrich, R; Martin, S E; McMillan, R; Miller, W

    1994-03-15

    We have conducted a 9-year multicenter trial of autologous bone marrow transplantation (ABMT) for acute myeloid leukemia (AML). Remission BM was purged in vitro using monoclonal antibodies (MoAbs; PM-81, AML-2-23) and complement targeting myeloid differentiation antigens (CD15, CD14). In 1988, the preparative regimen changed from 60 mg/kg/d cyclophosphamide x 2 and fractionated total body irradiation (TBI) total dose, 1,200 cGy (Cy/fTBI), to 4 mg/kg/d busulfan x 4 and 60 mg/kg/d Cy x 2 (Bu/Cy2). Recent analysis (October 1, 1993) shows that the Bu/Cy2 regimen along with the same MoAb purging method yields an improved outcome. Seven first complete-remission (CR) (CR1), 45 second- or third-CR (CR2/3), and 11 first-relapse (R1) patients were treated with chemotherapy and TBI or chemotherapy alone followed by ABMT with MoAb-purged BM. Median age at ABMT for those patients in CR 2/3 and R1 patients was 36 years. Twenty-nine CR 2/3 and R1 patients were conditioned with Cy/fTBI, and 27 CR2/3 and R1 patients were conditioned with Bu/CY. Using the Kaplan-Meier method, the CY/fTBI, CR2/3, and R1 patients have a 3-year disease-free survival (DFS) of 21%. On the other hand, the Bu/Cy2, CR2/3, and R1 patients have a 3-year DFS of 48%. Nineteen CR2/3 and R1 patients relapsed post-ABMT. On analysis by conditioning regimen, those treated with Cy/fTBI have a 3-year relapse rate (RR) of 58%, whereas the patients conditioned with Bu/Cy2 have a 39% 3-year RR. Long-term DFS can be achieved in about 50% of patients with advanced remissions and relapsed AML using Bu/Cy2 with MoAb-purged BM.

  3. USGS tethered ACP platforms: New design means more safety and accuracy

    Science.gov (United States)

    Morlock, S.E.; Stewart, J.A.; Rehmel, M.S.

    2004-01-01

    The US Geological Survey has developed an innovative tethered platform that supports an Acoustic Current Profiler (ACP) in making stream-flow measurements (use of the term ACP in this article refers to a class of instruments and not a specific brand name or model). The tethered platform reduces the hazards involved in conventional methods of stream-flow measurement. The use of the platform reduces or eliminates time spent by personnel in streams and boats or on bridges and cableway and stream-flow measurement accuracy is increased.

  4. Conformationally selective multidimensional chemical shift ranges in proteins from a PACSY database purged using intrinsic quality criteria

    Energy Technology Data Exchange (ETDEWEB)

    Fritzsching, Keith J., E-mail: kfritzsc@brandeis.edu [Brandeis University, Department of Chemistry (United States); Hong, Mei [Massachusetts Institute of Technology, Department of Chemistry (United States); Schmidt-Rohr, Klaus, E-mail: srohr@brandeis.edu [Brandeis University, Department of Chemistry (United States)

    2016-02-15

    We have determined refined multidimensional chemical shift ranges for intra-residue correlations ({sup 13}C–{sup 13}C, {sup 15}N–{sup 13}C, etc.) in proteins, which can be used to gain type-assignment and/or secondary-structure information from experimental NMR spectra. The chemical-shift ranges are the result of a statistical analysis of the PACSY database of >3000 proteins with 3D structures (1,200,207 {sup 13}C chemical shifts and >3 million chemical shifts in total); these data were originally derived from the Biological Magnetic Resonance Data Bank. Using relatively simple non-parametric statistics to find peak maxima in the distributions of helix, sheet, coil and turn chemical shifts, and without the use of limited “hand-picked” data sets, we show that ∼94 % of the {sup 13}C NMR data and almost all {sup 15}N data are quite accurately referenced and assigned, with smaller standard deviations (0.2 and 0.8 ppm, respectively) than recognized previously. On the other hand, approximately 6 % of the {sup 13}C chemical shift data in the PACSY database are shown to be clearly misreferenced, mostly by ca. −2.4 ppm. The removal of the misreferenced data and other outliers by this purging by intrinsic quality criteria (PIQC) allows for reliable identification of secondary maxima in the two-dimensional chemical-shift distributions already pre-separated by secondary structure. We demonstrate that some of these correspond to specific regions in the Ramachandran plot, including left-handed helix dihedral angles, reflect unusual hydrogen bonding, or are due to the influence of a following proline residue. With appropriate smoothing, significantly more tightly defined chemical shift ranges are obtained for each amino acid type in the different secondary structures. These chemical shift ranges, which may be defined at any statistical threshold, can be used for amino-acid type assignment and secondary-structure analysis of chemical shifts from intra

  5. Conformationally selective multidimensional chemical shift ranges in proteins from a PACSY database purged using intrinsic quality criteria.

    Science.gov (United States)

    Fritzsching, Keith J; Hong, Mei; Schmidt-Rohr, Klaus

    2016-02-01

    We have determined refined multidimensional chemical shift ranges for intra-residue correlations ((13)C-(13)C, (15)N-(13)C, etc.) in proteins, which can be used to gain type-assignment and/or secondary-structure information from experimental NMR spectra. The chemical-shift ranges are the result of a statistical analysis of the PACSY database of >3000 proteins with 3D structures (1,200,207 (13)C chemical shifts and >3 million chemical shifts in total); these data were originally derived from the Biological Magnetic Resonance Data Bank. Using relatively simple non-parametric statistics to find peak maxima in the distributions of helix, sheet, coil and turn chemical shifts, and without the use of limited "hand-picked" data sets, we show that ~94% of the (13)C NMR data and almost all (15)N data are quite accurately referenced and assigned, with smaller standard deviations (0.2 and 0.8 ppm, respectively) than recognized previously. On the other hand, approximately 6% of the (13)C chemical shift data in the PACSY database are shown to be clearly misreferenced, mostly by ca. -2.4 ppm. The removal of the misreferenced data and other outliers by this purging by intrinsic quality criteria (PIQC) allows for reliable identification of secondary maxima in the two-dimensional chemical-shift distributions already pre-separated by secondary structure. We demonstrate that some of these correspond to specific regions in the Ramachandran plot, including left-handed helix dihedral angles, reflect unusual hydrogen bonding, or are due to the influence of a following proline residue. With appropriate smoothing, significantly more tightly defined chemical shift ranges are obtained for each amino acid type in the different secondary structures. These chemical shift ranges, which may be defined at any statistical threshold, can be used for amino-acid type assignment and secondary-structure analysis of chemical shifts from intra-residue cross peaks by inspection or by using a provided

  6. Gas centrifuge purge method

    Science.gov (United States)

    Theurich, Gordon R.

    1976-01-01

    1. In a method of separating isotopes in a high speed gas centrifuge wherein a vertically oriented cylindrical rotor bowl is adapted to rotate about its axis within an evacuated chamber, and wherein an annular molecular pump having an intake end and a discharge end encircles the uppermost portion of said rotor bowl, said molecular pump being attached along its periphery in a leak-tight manner to said evacuated chamber, and wherein end cap closure means are affixed to the upper end of said rotor bowl, and a process gas withdrawal and insertion system enters said bowl through said end cap closure means, said evacuated chamber, molecular pump and end cap defining an upper zone at the discharge end of said molecular pump, said evacuated chamber, molecular pump and rotor bowl defining a lower annular zone at the intake end of said molecular pump, a method for removing gases from said upper and lower zones during centrifuge operation with a minimum loss of process gas from said rotor bowl, comprising, in combination: continuously measuring the pressure in said upper zone, pumping gas from said lower zone from the time the pressure in said upper zone equals a first preselected value until the pressure in said upper zone is equal to a second preselected value, said first preselected value being greater than said second preselected value, and continuously pumping gas from said upper zone from the time the pressure in said upper zone equals a third preselected value until the pressure in said upper zone is equal to a fourth preselected value, said third preselected value being greater than said first, second and fourth preselected values.

  7. Purge at West Valley

    Science.gov (United States)

    Mack, Warren

    1977-01-01

    Tells how the adviser of the student newspaper at West Valley College (Saratoga, California) was dismissed after the newspaper published stories based on investigations into alleged wrongdoings by administration members. (GW)

  8. Communications payloads for geostationary platforms

    Science.gov (United States)

    Fordyce, S. W.

    1978-01-01

    Trends in communication satellites show increasing reuse of the frequency spectrum through multiple spot beams and orthogonal polarization, as well as consortia operation. Current reliance on orbital arc separation for frequency reuse may be inadequate for the projected traffic growth and the orbital slotting proposals before the ITU. This paper notes that cost advantages can accrue through common use of spacecraft subsystems and multiple users' platforms aboard a common geostationary platform. The rationale for such platforms is described and potential payloads are suggested.

  9. Utilizing platforms in industrialized construction

    DEFF Research Database (Denmark)

    Bonev, Martin; Wörösch, Michael; Hvam, Lars

    2015-01-01

    construction companies. A promising approach adapted by operations management and design theory regards individual building projects as the adjustment and recombination of components and processes from a set of predefined platforms, while configuration systems assure feasible building solutions. Design...... methods map structural platform characteristics so as to balance commonality and distinctiveness. Originality/value – This paper proposes a general theory of platform-based development and execution in the industrialised construction sector, which goes beyond concurrent approaches of standardising...

  10. Web Platform Application

    Energy Technology Data Exchange (ETDEWEB)

    Paulsworth, Ashley [Sunvestment Group, Frederick, MD (United States); Kurtz, Jim [Sunvestment Group, Frederick, MD (United States); Brun de Pontet, Stephanie [Sunvestment Group, Frederick, MD (United States)

    2016-06-15

    Sunvestment Energy Group (previously called Sunvestment Group) was established to create a web application that brings together site hosts, those who will obtain the energy from the solar array, with project developers and funders, including affinity investors. Sunvestment Energy Group (SEG) uses a community-based model that engages with investors who have some affinity with the site host organization. In addition to a financial return, these investors receive non-financial value from their investments and are therefore willing to offer lower cost capital. This enables the site host to enjoy more savings from solar through these less expensive Community Power Purchase Agreements (CPPAs). The purpose of this award was to develop an online platform to bring site hosts and investors together virtually.

  11. Energy Tracking Software Platform

    Energy Technology Data Exchange (ETDEWEB)

    Ryan Davis; Nathan Bird; Rebecca Birx; Hal Knowles

    2011-04-04

    Acceleration has created an interactive energy tracking and visualization platform that supports decreasing electric, water, and gas usage. Homeowners have access to tools that allow them to gauge their use and track progress toward a smaller energy footprint. Real estate agents have access to consumption data, allowing for sharing a comparison with potential home buyers. Home builders have the opportunity to compare their neighborhood's energy efficiency with competitors. Home energy raters have a tool for gauging the progress of their clients after efficiency changes. And, social groups are able to help encourage members to reduce their energy bills and help their environment. EnergyIT.com is the business umbrella for all energy tracking solutions and is designed to provide information about our energy tracking software and promote sales. CompareAndConserve.com (Gainesville-Green.com) helps homeowners conserve energy through education and competition. ToolsForTenants.com helps renters factor energy usage into their housing decisions.

  12. The Creative Soccer Platform

    DEFF Research Database (Denmark)

    Johan Torp Rasmussen, Ludvig; Østergaard, Lars Domino

    2016-01-01

    Creativity is essential in soccer due to the unpredictable and complex situations occurring in the game, where stereotypical play gradually loses its efficiency. Further, creativity is an important psychological factor for the development of soccer expertise, and valuing creativity increases...... satisfaction and well-being. Although creative players are highly desired by coaches, the subject of cultivating creativity is mostly ignored and traditional training settings may even hamper the players' creativity. The purpose of this article is to introduce a novel approach for enhancing soccer players......' creativity, The Creative Soccer Platform (TCSP), and to demonstrate the implications of applying it in youth soccer practice, by means of soccer-specific creativity exercises. TCSP encompasses four theoretically based didactic principles (task focus, parallel thinking, horizontal thinking, and no experienced...

  13. Power Quality Indices Estimation Platform

    Directory of Open Access Journals (Sweden)

    Eliana I. Arango-Zuluaga

    2013-11-01

    Full Text Available An interactive platform for estimating the quality indices in single phase electric power systems is presented. It meets the IEEE 1459-2010 standard recommendations. The platform was developed in order to support teaching and research activities in electric power quality. The platform estimates the power quality indices from voltage and current signals using three different algorithms based on fast Fourier transform (FFT, wavelet packet transform (WPT and least squares method. The results show that the algorithms implemented are efficient for estimating the quality indices of the power and the platform can be used according to the objectives established. 

  14. Flexible experimental FPGA based platform

    DEFF Research Database (Denmark)

    Andersen, Karsten Holm; Nymand, Morten

    2016-01-01

    This paper presents an experimental flexible Field Programmable Gate Array (FPGA) based platform for testing and verifying digital controlled dc-dc converters. The platform supports different types of control strategies, dc-dc converter topologies and switching frequencies. The controller platform...... interface supporting configuration and reading of setup parameters, controller status and the acquisition memory in a simple way. The FPGA based platform, provides an easy way within education or research to use different digital control strategies and different converter topologies controlled by an FPGA...

  15. Product Platform Screening at LEGO

    DEFF Research Database (Denmark)

    Mortensen, Niels Henrik; Steen Jensen, Thomas; Nielsen, Ole Fiil

    2012-01-01

    Product platforms offer great benefits to companies developing new products in highly competitive markets. Literature describes how a single platform can be designed from a technical point of view, but rarely mentions how the process begins. How do companies identify possible platform candidates...... after a few changes had been applied to the initial process layout. This case study shows how companies must focus on a limited selection of simultaneous projects in order to keep focus. Primary stakeholders must be involved from the very beginning, and short presentations of the platform concepts...

  16. Platform evolution studies

    Science.gov (United States)

    Walton, Barbara A.

    1990-01-01

    The polar orbiting platform (POP), being developed by the Work Package 3 (WP3) Project at the Goddard Space Flight Center, will play a key role in the NASA Leadership Initiative, Mission to Planet Earth (MPE). It becomes, with the addition of payloads, an Earth observation satellite observatory. Mission to Planet Earth also has geostationary platforms (GEOP) as part of its global observational system. A study was begun in March 1988 to assess the applicability of the POP orbital replacement units (ORUs) for a geostationary Earth observing mission. Two test cases, representative of MPE payloads, were studied. Case A was used to emphasize the GEOP configuration and design; it used a Titan/Centaur to achieve orbit. Case B, considered to be much further in the future, included some assembly at the Space Station Freedom manned base and use of an orbital transfer vehicle to achieve orbit; requirements on the manned base to support such a mission were emphasized. The study found the POP systems more than adequate to meet GEOP requirements. Two types of changes were required for the POP ORUs: (1) modification to use only one surface for heat rejection; for the battery ORU, this meant 'opening up' the ORU to retain the radiator area with a corresponding decrease in depth; and (2) deletion of equipment not needed. The Case A configuration was shown to be within the planned capability of the Titan IV/Centaur. Assembly requirements were included for the Case B configuration, which is driven by the large microwave antennas of two of the payloads. The final review was April 19, 1989.

  17. Governing Logistics Information Platforms

    NARCIS (Netherlands)

    Klievink, A.J.; Aldewereld, H.M.; Knol, A.; Tan, Y.H.

    2014-01-01

    The Extended Single Window (ESW) project aims to support goods flows by Information and Communication Technology (ICT). Specifically, the project takes the concept of Single Windows (often used in the sense that governments offer a single portal or interface to which businesses can submit informatio

  18. Governing Logistics Information Platforms

    NARCIS (Netherlands)

    Klievink, A.J.; Aldewereld, H.M.; Knol, A.; Tan, Y.H.

    2014-01-01

    The Extended Single Window (ESW) project aims to support goods flows by Information and Communication Technology (ICT). Specifically, the project takes the concept of Single Windows (often used in the sense that governments offer a single portal or interface to which businesses can submit

  19. Governing Logistics Information Platforms

    NARCIS (Netherlands)

    Klievink, A.J.; Aldewereld, H.M.; Knol, A.; Tan, Y.H.

    2014-01-01

    The Extended Single Window (ESW) project aims to support goods flows by Information and Communication Technology (ICT). Specifically, the project takes the concept of Single Windows (often used in the sense that governments offer a single portal or interface to which businesses can submit informatio

  20. Platform Performance and Challenges - using Platforms in Lego Company

    DEFF Research Database (Denmark)

    Munk, Lone; Mortensen, Niels Henrik

    2009-01-01

    This article studies the performance and challenges of using nine implemented product platforms in LEGO Company. Most of these do produce results, but do not meet their goals due to challenges in their usage in the daily product. The main challenges are that the platforms are not being used...

  1. 29 CFR 1910.66 - Powered platforms for building maintenance.

    Science.gov (United States)

    2010-07-01

    ... supported carriages shall be obtained by gravity, by an attachment to a structural support, or by a combination of gravity and a structural support. The use of flowing counterweights to achieve stability is... platform, and this calculated value shall include the effect of one and one-half times the stall capacity...

  2. Feasibility of a simple microsieve-based immunoassay platform

    NARCIS (Netherlands)

    Zweitzig, D.R.; Tibbe, Arjan G.J.; Nguyen, A.T.; van Rijn, C.J.M.; Kopnitsky, M.J.; Cichonski, K.; Terstappen, Leonardus Wendelinus Mathias Marie

    2016-01-01

    The intrinsic properties of silicon microsieves, such as an optically flat surface, high overall porosity, and low flow resistance have led to an increasing number of biotechnology applications. In this report, the feasibility of creating a microsieve-based immunoassay platform was explored. Microsi

  3. Feasibility of a simple microsieve-based immunoassay platform

    NARCIS (Netherlands)

    Zweitzig, Daniel R.; Tibbe, Arjan G.; Nguyen, Ai T.; Rijn, van Cees J.M.; Kopnitsky, Mark J.; Cichonski, Kathleen; Terstappen, Leon W.M.M.

    2016-01-01

    The intrinsic properties of silicon microsieves, such as an optically flat surface, high overall porosity, and low flow resistance have led to an increasing number of biotechnology applications. In this report, the feasibility of creating a microsieve-based immunoassay platform was explored. Micr

  4. IMPROVEMENT OF PURGE METHOD OF SEED BED WATERREMOVAL IN UNIPOL POLYETHYLENE PROCESS%Unipol聚乙烯工艺中种子床置换方法的改进

    Institute of Scientific and Technical Information of China (English)

    栗文革

    2001-01-01

    This article introduced the original purge method of seed bed water-rem oval in Unipol polyethylene process,discussed the improved purge method and comp ared the effects of these two methods,suggested to use the improved purge method in practical operating procedures.%介绍了Unipol聚乙烯工艺中种子床脱水置换的常规方法,讨论了改进的置换方法,并对2种方法的效果进行了比较,建议在实际操作过程中采用改进的置换方法。

  5. Characterization of the Flow Field and Wind Speed Profiles in Microbalance Wind Tunnels for Measurement of Agent Fate

    Science.gov (United States)

    2005-10-01

    wind speeds. Figure 4 shows the internal components of the Model Q600, including the 23mm diameter flow tube. Sample Cup Reference Cup Purge Gas...using a constant temperature hot-film anemometer (IFA-300 system; TSI, Minneapolis, MN). Special care was taken to extend the hotwire probe calibration...were performed from within approximately 0.254mm of the sample pan to near the top of the tube. The hot wire anemometer probes were mounted on a high

  6. Dissolved carbon dioxide and oxygen concentrations in purge of vacuum-packaged pork chops and the relationship to shelf life and models for estimating microbial populations.

    Science.gov (United States)

    Adams, K R; Niebuhr, S E; Dickson, J S

    2015-12-01

    The objectives of this study were to determine the dissolved CO2 and O2 concentrations in the purge of vacuum-packaged pork chops over a 60 day storage period, and to elucidate the relationship of dissolved CO2 and O2 to the microbial populations and shelf life. As the populations of spoilage bacteria increased, the dissolved CO2 increased and the dissolved O2 decreased in the purge. Lactic acid bacteria dominated the spoilage microflora, followed by Enterobacteriaceae and Brochothrix thermosphacta. The surface pH decreased to 5.4 due to carbonic acid and lactic acid production before rising to 5.7 due to ammonia production. A mathematical model was developed which estimated microbial populations based on dissolved CO2 concentrations. Scanning electron microscope images were also taken of the packaging film to observe the biofilm development. The SEM images revealed a two-layer biofilm on the packaging film that was the result of the tri-phase growth environment. Copyright © 2015 Elsevier Ltd. All rights reserved.

  7. Inactivation of Salmonella spp., pathogenic Escherichia coli, Staphylococcus spp., or Listeria monocytogenes in chicken purge or skin using a 405-nm LED array.

    Science.gov (United States)

    Sommers, Christopher; Gunther, Nereus W; Sheen, Shiowshuh

    2017-06-01

    Raw poultry are sometimes contaminated with foodborne pathogens, which can lead to illness in humans. In recent years research has focused on a variety of light technologies to decontaminate food and food contact surfaces during meat and poultry processing. In this study we evaluated the ability of 405-nm light generated from an LED array to inactivate multi-isolate cocktails of either Salmonella spp., pathogenic Escherichia coli, Staphylococcus spp., or Listeria monocytogenes suspended in chicken purge or skin. When exposed to 180 J/cm(2) 405-nm light at two separate light intensities (300 mW/cm(2)/s or 150 mW/cm(2)/s) the maximum pathogen reduction on chicken skin was ca. 0.4 log. When the pathogens were suspended in chicken purge the maximum log reductions ranged from 0.23 to 0.68 log (180 J/cm(2); 150 mW/cm(2)/s) versus 0.69 to 1.01 log (180 J/cm(2); 300 mW/cm(2)/s). Log reductions of each pathogen, when they were subjected to heat shock prior to 405-nm light treatment, were reduced, indicating that thermal effects accounted for much of the bacterial inactivation. Published by Elsevier Ltd.

  8. Process sampling module coupled with purge and trap-GC-FID for in situ auto-monitoring of volatile organic compounds in wastewater.

    Science.gov (United States)

    Liu, Hsin-Wang; Liu, Yung-Tsun; Wu, Bei-Zen; Nian, Hung-Chi; Chen, Hsing-Jung; Chiu, Kong-Hwa; Lo, Jiunn-Guang

    2009-12-15

    An automatic sampling device, i.e., process sampling module (PSM), connected with a purge and trap-GC-FID system has been developed for real-time monitoring of VOCs in wastewater. The system was designed to simultaneously monitor 17 compounds, including one polar compound, i.e., acetone, and 16 non-polar compounds. The trapping tube is packed with two adsorbents, Carbopack B and Carbosieve III, to trap target compounds. For the purpose of in situ monitoring, the flush valve of the sampling tube is composed of two two-way valves and a time controller to prevent absorption interference of the residue. The optimal conditions for the analytical system include a 12 min purge time at a temperature of 60 degrees C, and 4 min of desorption time with a desorption temperature of 260 degrees C. Good chromatograms have been obtained with the analytical system even if a cryogenic device and de-misting were not used. The relative standards deviation (RSD) of the system is between 2% and 13.4%, and accuracies between 0.3 and 23.5% have been achieved. The detection limits of the method range from 0.32 to 2.39 ppb. In this system, the four parts, i.e., PSM, P&T, GC, and FID, were simple, reliable and rugged. Also, the interface of these four parts was simple and dependable.

  9. Simultaneous determination of eight common odors in natural water body using automatic purge and trap coupled to gas chromatography with mass spectrometry.

    Science.gov (United States)

    Deng, Xuwei; Liang, Gaodao; Chen, Jun; Qi, Min; Xie, Ping

    2011-06-17

    Production and fate of taste and odor (T&O) compounds in natural waters are a pressing environmental issue. Simultaneous determination of these complex compounds (covering a wide range of boiling points) has been difficult. A simple and sensitive method for the determination of eight malodors products of cyanobacterial blooms was developed using automatic purge and trap (P&T) coupled with gas chromatography-mass spectrometry (GC-MS). This extraction and concentration technique is solvent-free. Dimethylsulfide (DMS), dimethyltrisulfide (DMTS), 2-isopropyl-3-methoxypyrazine (IPMP), 2-isobutyl-3-methoxypyrazine (IBMP), 2-methylisoborneol (MIB), β-cyclocitral, geosmin (GSM) and β-ionone were separated within 15.3 min. P&T uses trap #07 and high-purity nitrogen purge gas. The calibration curves of the eight odors show good linearity in the range of 1-500 ng/L with a correlation coefficient above 0.999 (levels=8) and with residuals ranging from approximately 83% to 124%. The limits of detection (LOD) (S/N=3) are all below 1.5 ng/L that of GSM is even lower at 0.08 ng/L. The relative standard deviations (RSD) are between 3.38% and 8.59% (n=5) and recoveries of the analytes from water samples of a eutrophic lake are between 80.54% and 114.91%. This method could be widely employed for monitoring these eight odors in natural waters.

  10. Water-based gas purge microsyringe extraction coupled with liquid chromatography for determination of alkylphenols from sea food Laminaria japonica Aresh.

    Science.gov (United States)

    Yang, Cui; Zhao, Jinhua; Wang, Juan; Yu, Hongling; Piao, Xiangfan; Li, Donghao

    2013-07-26

    A novel organic solvent-free mode of gas purge microsyringe extraction, termed water-based gas purge microsyringe extraction, was developed. This technique can directly extract target compounds in wet samples without any drying process. Parameters affecting the extraction efficiency were investigated. Under optimal extraction conditions, the recoveries of alkylphenols were between 87.6 and 105.8%, and reproducibility was between 5.2 and 12.1%. The technique was also used to determine six kinds of alkylphenols (APs) from samples of Laminaria japonica Aresh. The OP and NP were detected in all the samples, and concentrations ranged from 26.0 to 54.5ngg(-1) and 45.0-180.4ngg(-1), respectively. The 4-n-butylphenol was detected in only one sample and its concentration was very low. Other APs were not detected in L. japonica Aresh samples. The experimental results demonstrated that the technique is fast, simple, non-polluting, allows for quantitative extraction, and a drying process was not required for wet samples. Since only aqueous solution and a conventional microsyringe were used, this technique proved affordable, efficient, and convenient for the extraction of volatile and semivolatile ionizable compounds.

  11. Rapid prototyping of robotic platforms

    CSIR Research Space (South Africa)

    De Ronde, Willis

    2016-11-01

    Full Text Available Building a robotic platform from raw materials can take anything from a few weeks to a few years to complete, depending on the complexity and size of the platform. This paper aims to introduce a novel approach of using abrasive waterjet machining...

  12. Preparing for a Product Platform

    DEFF Research Database (Denmark)

    Fiil-Nielsen, Ole; Munk, Lone; Mortensen, Niels Henrik

    2005-01-01

    they lead to increased sales due to more customized product as well as decreased costs due to reuse, making a product development platform a very profitable strategy for product developing companies. A successful implementation of a product development platform is not straightforward though...

  13. A Barcode-Free Combinatorial Screening Platform for Matrix Metalloproteinase Screening

    OpenAIRE

    Rane, Tushar D.; Zec, Helena C.; Wang, Tza-Huei

    2014-01-01

    Application of droplet microfluidics to combinatorial screening applications remains elusive because of the need for composition-identifying unique barcodes. Here we propose a barcode-free continuous flow droplet microfluidic platform to suit the requirements of combinatorial screening applications. We demonstrate robust and repeatable functioning of this platform with matrix metalloproteinase activity screening as a sample application.

  14. A barcode-free combinatorial screening platform for matrix metalloproteinase screening.

    Science.gov (United States)

    Rane, Tushar D; Zec, Helena C; Wang, Tza-Huei

    2015-02-03

    Application of droplet microfluidics to combinatorial screening applications remains elusive because of the need for composition-identifying unique barcodes. Here we propose a barcode-free continuous flow droplet microfluidic platform to suit the requirements of combinatorial screening applications. We demonstrate robust and repeatable functioning of this platform with matrix metalloproteinase activity screening as a sample application.

  15. Technical evaluation of the electrical, instrumentation, and control design aspects of the override of containment purge valve isolation and other engineered safety feature signals for the Fort Calhoun Nuclear Power Plant

    Energy Technology Data Exchange (ETDEWEB)

    Hackett, D.B.

    1980-01-01

    This report documents the technical evaluation of the electrical, instrumentation, and control design aspects of the override of containment purge valve isolation and other engineered safety feature signals for the Fort Calhoun nuclear power plant. The review criteria are based on IEEE Std-279-1971 requirements for the safety signals to all purge and ventilation isolation valves. This report is supplied as part of the Selected Electrical, Instrumentation, and Control Systems Issues Program being conducted for the US Nuclear Regulatory Commission by Lawrence Livermore Laboratory.

  16. Long-term progression-free survival of mantle cell lymphoma after intensive front-line immunochemotherapy with in vivo-purged stem cell rescue: a nonrandomized phase 2 multicenter study by the Nordic Lymphoma Group

    DEFF Research Database (Denmark)

    Geisler, C.H.; Kolstad, A.; Laurell, A.

    2008-01-01

    purged autologous stem cell support. Overall and complete response was achieved in 96% and 54%, respectively. The 6-year overall, event-free, and progression-free survival were 70%, 56%, and 66%, respectively, with no relapses occurring after 5 years. Multivariate analysis showed Ki-67 to be the sole......, and progression-free survival, the duration of molecular remission, and the proportion of PCR-negative stem cell products were significantly increased (P purged stem cell support can lead to long-term progression-free survival of MCL and perhaps cure. Registered...

  17. Product Platform Screening at LEGO

    DEFF Research Database (Denmark)

    Mortensen, Niels Henrik; Steen Jensen, Thomas; Nielsen, Ole Fiil

    2012-01-01

    Product platforms offer great benefits to companies developing new products in highly competitive markets. Literature describes how a single platform can be designed from a technical point of view, but rarely mentions how the process begins. How do companies identify possible platform candidates......, and how do they assess if these candidates have enough potential to be worth implementing? Danish toy manufacturer LEGO has systematically gone through this process twice. The first time the results were poor; almost all platform candidates failed. The second time, though, has been largely successful...... after a few changes had been applied to the initial process layout. This case study shows how companies must focus on a limited selection of simultaneous projects in order to keep focus. Primary stakeholders must be involved from the very beginning, and short presentations of the platform concepts...

  18. ADAPTABLE ALTERNATE REALITY GAMES PLATFORM

    Directory of Open Access Journals (Sweden)

    Liviu-Adrian Cotfas

    2013-12-01

    Full Text Available In this paper, we present an alternate reality games platform that facilitates the creation of ARG projects with different themes and sizes. The platform is well integrated with the most important social media networks, thus facilitating both the involvement of the public and the creation of a more engaging interaction for the participants. A cloud-based architecture was used in order to allow the platform to easily accommodate projects of various sizes and to provide a good level of scalability. The platform is fully localizable in any language and multiple languages can be used at once to create projects that target users from different countries. An initial project that uses gamification to create an immersive learning environment has been created around the developed platform. The project combines professional and public feedback in order to provide an enhanced learning experience.

  19. Paper based electronics platform

    KAUST Repository

    Nassar, Joanna Mohammad

    2017-07-20

    A flexible and non-functionalized low cost paper-based electronic system platform fabricated from common paper, such as paper based sensors, and methods of producing paper based sensors, and methods of sensing using the paper based sensors are provided. A method of producing a paper based sensor can include the steps of: a) providing a conventional paper product to serve as a substrate for the sensor or as an active material for the sensor or both, the paper product not further treated or functionalized; and b) applying a sensing element to the paper substrate, the sensing element selected from the group consisting of a conductive material, the conductive material providing contacts and interconnects, sensitive material film that exhibits sensitivity to pH levels, a compressible and/or porous material disposed between a pair of opposed conductive elements, or a combination of two of more said sensing elements. The method of sensing can further include measuring, using the sensing element, a change in resistance, a change in voltage, a change in current, a change in capacitance, or a combination of any two or more thereof.

  20. Plat_Forms -- a contest: The web development platform comparison

    CERN Document Server

    Prechelt, Lutz

    2008-01-01

    "Plat_Forms" is a competition in which top-class teams of three programmers compete to implement the same requirements for a web-based system within 30 hours, each team using a different technology platform (Java EE, .NET, PHP, Perl, Python, or Ruby on Rails). The results will provide new insights into the real (rather than purported) pros, cons, and emergent properties of each platform. The evaluation will analyze many aspects of each solution, both external (usability, functionality, reliability, performance, etc.) and internal (structure, understandability, flexibility, etc.).

  1. 螺旋折流板管壳式换热器内LNG混合介质流动冷凝特性仿真平台开发及影响因素分析%Simulation Platform Development and Influence Factor Analysis for Flow Condensation Characteristics of LNG Mixture in Shell-tube Heat Exchanger with Helical Baffles

    Institute of Scientific and Technical Information of China (English)

    黄庆楠; 陈杰; 杨文刚; 罗婷婷; 丁国良; 胡海涛

    2015-01-01

    螺旋折流板管壳式换热器用于冷凝混合烃类介质时,会产生冷凝不均导致设备效率降低等问题;但是由于换热器体积和能耗巨大,难以通过大量的实验测试得出换热器性能的规律。为了了解管壳式换热器内LNG混合介质流动冷凝特性,本文建立了一种用于螺旋折流板管壳式换热器内LNG混合介质流动冷凝的仿真模型。该模型考虑了流动过程中的传热传质及气相分率的变化,体现了换热器结构、螺旋折流板参数及工质物性等各种因素对流动和传热的影响,同时保证仿真的计算速度。此外,采用该模型开发的仿真平台具有友好的用户界面,方便用户输入仿真参数,准确快捷地对换热器性能进行仿真,并以形象直观的方式输出仿真结果。基于开发的仿真平台,对螺旋折流板管壳式换热器内 LNG 混合介质流动冷凝特性的结构影响因素进行了分析,给出了最佳螺旋角的推荐值。%When the shell-tube heat exchanger with helical baffles is used for cooling mixed hydrocarbons, it may cause the unbalance of condensation and reduce the equipment efficiency. But due to huge volume and energy consumption of the heat exchanger, it is difficult to study the performance rule by a large number of experimental tests. In order to understand the flow condensation characteristics of LNG mixture in the shell side, a simulation model of the seawater heat exchanger with helical baffles is developed in this paper. The heat and mass transfer and the change of the gas fraction along the flow process are considered in the model. And it reflects the influence of the heat exchanger structure, helical baffle parameters, flow process and fluid properties on flowing and heat exchanging. The simulation speed can be guaranteed by segmentation parameters method as well. In addition, the friendly graphic user interface has also been developed in this simulation platform

  2. Platform projections, compilers, interpreters and portability

    NARCIS (Netherlands)

    Bergstra, J.A.; Loots, M.E.

    1999-01-01

    Platform projection semantics extends projection semantics by means of the encapsulation of a processor used for program execution. Platform projection semantics abstracts from platform specific details. For a given program its platform projection semantics may be platform-independent. Two forms

  3. Vertical Relationships within Platform Marketplaces

    Directory of Open Access Journals (Sweden)

    Mark J. Tremblay

    2016-07-01

    Full Text Available In two-sided markets a platform allows consumers and sellers to interact by creating sub-markets within the platform marketplace. For example, Amazon has sub-markets for all of the different product categories available on its site, and smartphones have sub-markets for different types of applications (gaming apps, weather apps, map apps, ridesharing apps, etc.. The network benefits between consumers and sellers depend on the mode of competition within the sub-markets: more competition between sellers lowers product prices, increases the surplus consumers receive from a sub-market, and makes platform membership more desirable for consumers. However, more competition also lowers profits for a seller which makes platform membership less desirable for a seller and reduces seller entry and the number of sub-markets available on the platform marketplace. This dynamic between seller competition within a sub-market and agents’ network benefits leads to platform pricing strategies, participation decisions by consumers and sellers, and welfare results that depend on the mode of competition. Thus, the sub-market structure is important when investigating platform marketplaces.

  4. Vega flow assurance system

    Energy Technology Data Exchange (ETDEWEB)

    Larsen, Marit; Munaweera, Sampath

    2010-07-01

    Vega is a gas condensate field located at the west coast of Norway and developed as a tie-in to the Gjoea platform. Operator is Statoil, production startup is estimated to the end of 2010. Flow assurance challenges are high reservoir pressure and temperature, hydrate and wax control, liquid accumulation and monitoring the well/template production rates. The Vega Flow Assurance System (FAS) is a software that supports monitoring and operation of the field. The FAS is based FlowManagerTM designed for real time systems. This is a flexible tool with its own steady state multiphase- and flow assurance models. Due to the long flowlines lines and the dynamic behavior, the multiphase flow simulator OLGA is also integrated in the system. Vega FAS will be used as: - An online monitoring tool - An offline what-if simulation and validation tool - An advisory control system for well production allocation. (Author)

  5. RESULTS FROM EPA FUNDED RESEARCH PROGRAMS ON THE IMPORTANCE OF PURGE VOLUME, SAMPLE VOLUME, SAMPLE FLOW RATE AND TEMPORAL VARIATIONS ON SOIL GAS CONCENTRATIONS

    Science.gov (United States)

    Two research studies funded and overseen by EPA have been conducted since October 2006 on soil gas sampling methods and variations in shallow soil gas concentrations with the purpose of improving our understanding of soil gas methods and data for vapor intrusion applications. Al...

  6. Platform decisions supported by gaming

    DEFF Research Database (Denmark)

    Hansen, Poul H. Kyvsgård; Mikkola, Juliana Hsuan

    2007-01-01

    Platform is an ambiguous multidisciplinary concept. The philosophy behind it is easy to communicate and makes intuitively sense. However, the ease in communication does overshadow the high complexity when the concept is implemented. The practical industrial platform implementation challenge can...... is the application of on-line games in order to provide training for decision makers and in order to generate overview over the implications of platform decisions. However, games have to be placed in a context with other methods and we argue that a mixture of games, workshops, and simulations can provide improved...

  7. Experimental studies of the effects of ZnPcS2P2-based-photodynamic therapy on bone marrow purging

    Institute of Scientific and Technical Information of China (English)

    HUANG Hui-fang; CHEN Yuan-zhong; WU Yong

    2005-01-01

    Background An effective purging technique plays an important role in autologous hematopoietic stem cells transplantation. Photodynamic therapy (PDT) provides a novel approach for this purpose. This study dealt with the purging effects of di-sulfo-di-phthalimidomethyl phthalolcyanine zinc (ZnPcS2P2)-based photodynamic therapy (ZnPc-PDT). Methods Fluorescence intensity of cell extracts was measured using a fluoresence spectrophotometry. The proliferative potency of K562 cells and HL60 cells was detected using MTT colorimetric assay, Typan blue dye exclusion method, colony formation test. The proliferative potency of normal hematopoietic cells was evaluated using mixture colony-forming unit (CFU-Mix), granulocyte-macrophage colony-forming unit (CFU-GM), and erythrocyte colony-forming unit (CFU-E) assays. K562 cells were mixed with normal mononuclear cells (MNCs) at ratios of 1∶ 100 and 1∶ 1000 for creating the model of simulated remission bone marrow. Colony formation test and nested-RT-PCR were carried out to detect the residual K562 cells in cell mixture. Results After a 5-hour incubation with ZnPcS2P2, the content of ZnPcS2P2 in normal MNCs was the lowest value. At the same time, the content in K562 cells and HL60 cells was very high. Therefore, the time point was selected as the optimal one for irradiating the cell suspensions. ZnPc-PDT could significantly kill proliferative K562 cells and HL60 cells in a dose-dependent manner. At the concentration of 1.0 μg/ml, the inhibitory rate of ZnPc-PDT on the colony formation was 100% for K562 cells, 89.7% for HL60 cells. 0.25 μg/ml ZnPc-PDT could completely photoinactivate residual K562 cells in the simulated remission bone marrow. Under an identical condition, the inhibitory rates of CFU-Mix, CFU-GM, CFU-E were 18.0%, 18.6%, and 17.8% respectively. Conclusion ZnPc-PDT appears to be a promising approach for bone marrow purging.

  8. Lattice QCD simulations using the OpenACC platform

    Science.gov (United States)

    Majumdar, Pushan

    2016-10-01

    In this article we will explore the OpenACC platform for programming Graphics Processing Units (GPUs). The OpenACC platform offers a directive based programming model for GPUs which avoids the detailed data flow control and memory management necessary in a CUDA programming environment. In the OpenACC model, programs can be written in high level languages with OpenMP like directives. We present some examples of QCD simulation codes using OpenACC and discuss their performance on the Fermi and Kepler GPUs.

  9. NASA's geostationary communications platform program

    Science.gov (United States)

    Ramler, J.; Durrett, R.

    1984-01-01

    This paper reviews recent trends in communications satellites and explains NASA's current interest in geostationary communications platforms. Large communications platforms capable of supporting multiple payloads with common utilities have been examined in a number of studies since 1974 and appear to offer a number of potential advantages. In 1981, an Industry Briefing and Workshop sponsord by NASA focused on the institutional, operational and technical issues that will influence the implementation of geostationary platforms. The workshop identified numerous issues and problem areas that needed more detailed study. To address the issues/problems identified, a NASA geostationary communications platform program has been developed. This program is described, focusing on the initial studies to be performed.

  10. Platform attitude data acquisition system

    Digital Repository Service at National Institute of Oceanography (India)

    Afzulpurkar, S.

    A system for automatic acquisition of underwater platform attitude data has been designed, developed and tested in the laboratory. This is a micro controller based system interfacing dual axis inclinometer, high-resolution digital compass...

  11. Elevated Fixed Platform Test Facility

    Data.gov (United States)

    Federal Laboratory Consortium — The Elevated Fixed Platform (EFP) is a helicopter recovery test facility located at Lakehurst, NJ. It consists of a 60 by 85 foot steel and concrete deck built atop...

  12. Platforms for Innovation and Internationalization

    DEFF Research Database (Denmark)

    Rasmussen, Erik Stavnsager; Petersen, Nicolaj Hannesbo

    2017-01-01

    The high-tech global startup has many challenges related to both innovation and internationalization. From a Danish cluster of Welfare Tech firms, eight innovative and international firms were selected and interviewed. Such firms typically have to be agile and operate in virtual networks in almost...... all parts of their value chains. This article contributes to the understanding of how innovation and internationalization to a great extent are interlinked. The firms have developed a core product or service offering, which the firms often describe as “a platform”. Around the platform, they develop...... their products and services for new customers and users in new countries. The firms have to sustain a strong focus on the platform while at the same time developing their platform solution for new products, new customers, and new markets. This pivoting makes it possible to use the platform in a new context...

  13. Practice of Blending the Methanol Purge Gas into the Fuel for Gas-fired Boilers%甲醇弛放气用于掺烧燃气锅炉的实践

    Institute of Scientific and Technical Information of China (English)

    董越茂; 焦东雄; 乔春红

    2011-01-01

    The utilization of the methanol purge gas was introduced, and the theoretical combustion temperature and the excess air factor of the purge gas as a blend for the gas-fired boilers were calculated and analyzed. The method of delivering the purge gas to the boilers, and the pressure reduction of the gas, etc. Were put forward. Practice proved that there was practically no adverse impact on the gas-fired boilers when the methanol purge gas was blended into the fuel gas, yet quite good social and economic benefits could be obtained.%介绍了山西焦化股份有限公司甲醇生产中甲醇弛放气的利用情况,对弛放气用于掺烧燃气锅炉的理论燃烧温度和过量空气系数进行了计算和分析;并介绍了弛放气用于掺烧燃气锅炉时弛放气接出位置的确定、所采取的输送方式、减压方式等技术措施,实践证明甲醇弛放气掺烧对燃气锅炉系统基本没有不良影响,具有较好的社会和经济效益.

  14. Pressure Drop Measurement of Column Weight in Disc and Doughnut Pulsed Extraction Column by External Air Purge Method%外置吹气杯测量折流板脉冲萃取柱柱重压降

    Institute of Scientific and Technical Information of China (English)

    王悦云; 李少伟; 景山

    2013-01-01

    The pressure drop of column weight was measured in a disc and doughnut pulsed extraction column with the inertial diameter of 0.3 m and height of 5.6 m by in-ternal and external air purge methods ,respectively .The experimental results show that the pressure drops of column weight measured by external air purge method are in good agreement with those by internal air purge method ,therefore ,the external air purge method is recommended to measure the pressure drop of column weight in the pulsed extraction column in plutonium purification cycle .%在内径为0.3m和高度为5.6m的折流板脉冲萃取柱中,分别采用内置吹气杯和外置吹气杯对柱重压降信号进行了测量和比较。实验结果表明,两种吹气杯安装方式所测量的结果一致。因此,为了避免由于内置吹气杯所造成的钚纯化循环脉冲萃取柱异形下澄清段的设计和加工难度,推荐可使用外置吹气杯来测量该工段的脉冲萃取柱柱重压降。

  15. Purge gas producing LNG in coke oven gas to methanol%焦炉煤气制甲醇的弛放气生产液化天然气

    Institute of Scientific and Technical Information of China (English)

    董永波

    2015-01-01

    通过对20万t/a焦炉煤气制取甲醇过程中产生的甲醇弛放气进行分析研究,提出了利用甲醇弛放气合成液化天然气的循环再利用途径,并且与利用甲醇弛放气合成氨、合成甲醇等循环再利用方法对比,得出了利用甲醇弛放气生产液化天然气是当前最有效、最经济的利用途径,项目实施后企业每年可以生产液化天然气1.34万t,收益2200万元。%The paper analyzes and investigates methanol purge gas producing in 200 000 t/a coke oven gas to methanol process, it proposes recycling method in producing LNG by methanol purge gas, it obtains that producing LNG by methanol purge gas is the most effective and most economical way after contracting recycling methods between synthesis ammonia and synthesis methanol by methanol purge gas. After the implementation of the project, the company can produce LNG 13 400 t/a, 22 million yuan profit.

  16. 甲醇弛放气掺入量的变化对焦炉加热的影响%The Impact of Variation in the Blending Ratio of Methanol Purge Gas on the Heating of the Coke Ovens

    Institute of Scientific and Technical Information of China (English)

    严加才; 于泳; 李建华

    2011-01-01

    结合开滦京唐港煤化工园区生产实际,根据甲醇弛放气波动造成煤气热值变化,来计算所需空气和产生废气量以及炉温的变化.结果表明,弛放气掺入量在0%-40%时,若未调节入炉空气量,弛放气每降低10%,理论燃烧温度会升高85℃左右,并提出弛放气波动情况下的调节意见,为焦炉加热调温提供参考.%The amount of air required, the amount of the exhaust gas and the oven temperature were calculated based on the actual production of the Kailuan Coal Chemical Industial Park, in particular, the change in the calorific value due to the fluctuation of the methanol purge gas. Results showed that when the amount of purge gas was between 0% and 40%, the theoretical combustion temperature would raise by approximately 85℃ with every 10% of decrease of the purge gas, on condition that the air feed into the oven was not regulated. The way to regulate the heating of the oven when the purge gas fluctuated was suggested. This can serve as a reference for heating and temperature regulation of the coke ovens.

  17. 大型联合化工项目中压蒸汽管网吹扫方案及实施%Purging Scheme and Implementation of Medium Pressure Steam Pipe Network of Large Scale Integration Chemical Project

    Institute of Scientific and Technical Information of China (English)

    郭玉林; 刘俊青; 史学廷

    2014-01-01

    介绍了中压蒸汽管网总体吹扫方案及实施情况,并针对吹扫过程中出现的问题提出了相应的解决措施。此次中压蒸汽管网吹扫工作取得了圆满成功,对二期项目建设过程中改进管线设计、施工、监理、验收方法以及同类管线吹扫工作具有十分重要的参考意义。%The overall purging scheme of medium pressure steam pipe network and implementation is presented , and in connection with problems in purging process , relevant counter measures are suggested .The medium pressure steam pipe network purging scheme is a complete success , and it has important reference value for improvement of pipe network design , construction , supervision , acceptance check method in construction of the second phase and for same kind of pipe network purging .

  18. Heat Recovery Steam Generators for Combined Typical Cycle Steam Purge%9F等级燃气蒸汽联合循环机组余热锅炉吹管方式的选择

    Institute of Scientific and Technical Information of China (English)

    许宏宇

    2009-01-01

    根据余热锅炉三压系统不同压力级选择吹管方式,提高蒸汽吹扫的效果.%According to the different ranks of pressurizing system for the HRSG,we can select the steam-line blowing way to improve the purging effect of steam.

  19. Disentangling Competition Among Platform Driven Strategic Groups

    DEFF Research Database (Denmark)

    Kazan, Erol; Tan, Chee-Wee; Lim, Eric

    2015-01-01

    In platform-driven markets, competitive advantage is derived from superior platform design and configurations. For this reason, platform owners strive to create unique and inimitable platform configurals to maintain and extend their competitiveness within network economies. To disentangle firm...... competition within platform-driven markets, we opted for the UK mobile payment market as our empirical setting. By embracing the theoretical lens of strategic groups and digital platforms, this study supplements prior research by deriving a taxonomy of platform-driven strategic groups that is grounded...... on competitive attributes of platform- driven markets; namely interfirm modularity and strategic linkages....

  20. Disentangling Competition Among Platform Driven Strategic Groups

    DEFF Research Database (Denmark)

    Kazan, Erol; Tan, Chee-Wee; Lim, Eric

    2015-01-01

    competition within platform-driven markets, we opted for the UK mobile payment market as our empirical setting. By embracing the theoretical lens of strategic groups and digital platforms, this study supplements prior research by deriving a taxonomy of platform-driven strategic groups that is grounded......In platform-driven markets, competitive advantage is derived from superior platform design and configurations. For this reason, platform owners strive to create unique and inimitable platform configurals to maintain and extend their competitiveness within network economies. To disentangle firm...... on competitive attributes of platform- driven markets; namely interfirm modularity and strategic linkages....

  1. Determination of 19 volatile organic compounds in wastewater effluents from different treatments by purge and trap followed by gas-chromatography coupled to mass spectrometry.

    Science.gov (United States)

    Barco-Bonilla, Nieves; Plaza-Bolaños, Patricia; Fernández-Moreno, José Luis; Romero-González, Roberto; Frenich, Antonia Garrido; Vidal, José Luis Martínez

    2011-07-01

    A rapid and simple methodology based on purge and trap with gas-chromatography coupled to triple quadrupole mass spectrometry has been developed for the analysis of 19 volatile organic compounds (VOCs) in wastewater (WW) effluents from four different treatments. The determination was carried out in the raw WW effluents, which were not submitted to any pre-treatment (e.g., filtration). A matrix effect study was also performed, concluding that solvent calibration was adequate to quantify VOCs in WW effluent samples containing a variety of suspended particulate matter. Adequate validation parameters were obtained with recovery values in the range 73-124% and precision values lower than 24%. Limits of quantification were established at 0.1 μg L(-1) for all VOCs. The proposed method was applied to the analysis of WW samples, detecting chloroform and toluene at concentrations ranging from 0.1 to 4.80 μg L(-1).

  2. PURGING SYSTEM AFTER CONTROLLED-COOLING BASED ON TRIZ INNOVATION THEROY%基于TRIZ创新理论的控冷后吹扫系统

    Institute of Scientific and Technical Information of China (English)

    崔忠信

    2015-01-01

    通过冲突理论、物质-场理论等建立功能模型树、物质-场模型进行分析、求解,最终找到以吹扫为主的指导方案,该方案经过具体化后形成吹扫系统并投入实际使用。该吹扫系统在河北钢铁技术研究总院中试工厂550热轧机的控冷系统进行安装试验。使用该系统可以完全去除冷却后的残余水,明显提高冷却后测温的准确性以及钢板温度的均匀性。%The guide plan with purging as main target is found out at last through analysis and getting the solu-tion by means of functional model tree and material-field model built with conflict theory and material-field theory.This plan is materialized into a purging system, and the later is put into actual application.This system is installed and tested in controlled-cooling system of 550 hot rolling mill of pilot plant of the institu-te.This system can completely eliminate the residual water after cooling;obviously improve the accuracy of temperature measuring after cooling and the homogeneity of steel plate temperature.

  3. Rapid response to intensive treatment for bulimia nervosa and purging disorder: A randomized controlled trial of a CBT intervention to facilitate early behavior change.

    Science.gov (United States)

    MacDonald, Danielle E; McFarlane, Traci L; Dionne, Michelle M; David, Lauren; Olmsted, Marion P

    2017-09-01

    Rapid response to cognitive behavior therapy (CBT) for eating disorders (i.e., rapid and substantial change to key eating disorder behaviors in the initial weeks of treatment) robustly predicts good outcome at end-of-treatment and in follow up. The objective of this study was to determine whether rapid response to day hospital (DH) eating disorder treatment could be facilitated using a brief adjunctive CBT intervention focused on early change. 44 women (average age 27.3 [8.4]; 75% White, 6.3% Black, 6.9% Asian) were randomly assigned to 1 of 2 4-session adjunctive interventions: CBT focused on early change, or motivational interviewing (MI). DH was administered as usual. Outcomes included binge/purge frequency, Eating Disorder Examination-Questionnaire and Difficulties in Emotion Regulation Scale. Intent-to-treat analyses were used. The CBT group had a higher rate of rapid response (95.7%) compared to MI (71.4%; p = .04, V = .33). Those who received CBT also had fewer binge/purge episodes (p = .02) in the first 4 weeks of DH. By end-of-DH, CBT participants made greater improvements on overvaluation of weight and shape (p = .008), and emotion regulation (ps rapid and nonrapid responders (ps > .05). The results of this study demonstrate that rapid response can be clinically facilitated using a CBT intervention that explicitly encourages early change. This provides the foundation for future research investigating whether enhancing rates of rapid response using such an intervention results in improved longer term outcomes. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

  4. Purge-assisted headspace solid-phase microextraction combined with gas chromatography/mass spectrometry for the determination of trace nitrated polycyclic aromatic hydrocarbons in aqueous samples.

    Science.gov (United States)

    Hung, Cheng-Han; Ho, Hsin-Pin; Lin, Mei-Tzu; Chen, Chung-Yu; Shu, Youn-Yuen; Lee, Maw-Rong

    2012-11-23

    This study describes a new procedure, namely, purge-assisted headspace solid phase microextraction combined with gas chromatography/negative ion chemical ionization mass spectrometry (PA/HS-SPME-GC/NICI-MS), which is used to determine seven nitrated polycyclic aromatic hydrocarbons (NPAHs) in aqueous samples. High extraction efficiency was obtained with PA/HS-SPME with polydimethylsiloxane (PDMS) fiber coating. A programmable temperature vaporizing (PTV) inlet was used in the desorption process. Selected ion monitoring (SIM) was used for quantitative and qualitative purposes. The linear range of detection of the proposed method was 5-5000 pg/mL with coefficients of determination between 0.995 and 0.999. Limits of detection (LODs) for seven NPAHs were 0.01-0.06 pg/mL. The relative standard deviation was below 12.7% at a concentration of 50 pg/mL. Compared with headspace-solid phase microextraction (HS-SPME), the purge procedure enhanced the extraction efficiency for high boiling point analytes, such as 7-nitrobenz[a]anthracene (7-NBA) and 6-nitrochrysene (6-NC). The proposed method provides a sensitive method for NPAH analysis at the pg/mL level. The application of the proposed method for the determination of trace NPAHs in real samples was investigated by analyzing aqueous samples from rivers. The concentrations of NPAHs detected from the samples ranged from 5.2 to 7.5 pg/mL. This method was applied successfully in the analysis of trace NPAHs in river samples.

  5. A Typology of Multi-sided Platforms

    DEFF Research Database (Denmark)

    Staykova, Kalina Stefanova; Damsgaard, Jan

    2015-01-01

    exemplary cases which allow us to illustrate the platform heterogeneity and to support new MSPs typology. As examples we include a physical two-sided platform (Gatwick Airport) that adds a third side, a digital one-sided platform transformed into being two-sided (Pingit) and a digital one-sided platform......In this paper we address how the composition of a platform impacts the platform’s business model. By platform’s business model we mean platform features, platform architecture and platform governance. To this end, we construct the Platform Business Model Framework. We apply the framework to three...... in several configurations. The particular platform architecture can explain the difficulties in designing a viable business models for platforms....

  6. Seqcrawler: biological data indexing and browsing platform

    Directory of Open Access Journals (Sweden)

    Sallou Olivier

    2012-07-01

    Full Text Available Abstract Background Seqcrawler takes its roots in software like SRS or Lucegene. It provides an indexing platform to ease the search of data and meta-data in biological banks and it can scale to face the current flow of data. While many biological bank search tools are available on the Internet, mainly provided by large organizations to search their data, there is a lack of free and open source solutions to browse one’s own set of data with a flexible query system and able to scale from a single computer to a cloud system. A personal index platform will help labs and bioinformaticians to search their meta-data but also to build a larger information system with custom subsets of data. Results The software is scalable from a single computer to a cloud-based infrastructure. It has been successfully tested in a private cloud with 3 index shards (pieces of index hosting ~400 millions of sequence information (whole GenBank, UniProt, PDB and others for a total size of 600 GB in a fault tolerant architecture (high-availability. It has also been successfully integrated with software to add extra meta-data from blast results to enhance users’ result analysis. Conclusions Seqcrawler provides a complete open source search and store solution for labs or platforms needing to manage large amount of data/meta-data with a flexible and customizable web interface. All components (search engine, visualization and data storage, though independent, share a common and coherent data system that can be queried with a simple HTTP interface. The solution scales easily and can also provide a high availability infrastructure.

  7. Biodiversity information platforms: From standards to interoperability

    Directory of Open Access Journals (Sweden)

    Walter Berendsohn

    2011-11-01

    Full Text Available One of the most serious bottlenecks in the scientific workflows of biodiversity sciences is the need to integrate data from different sources, software applications, and services for analysis, visualisation and publication. For more than a quarter of a century the TDWG Biodiversity Information Standards organisation has a central role in defining and promoting data standards and protocols supporting interoperability between disparate and locally distributed systems. Although often not sufficiently recognized, TDWG standards are the foundation of many popular Biodiversity Informatics applications and infrastructures ranging from small desktop software solutions to large scale international data networks. However, individual scientists and groups of collaborating scientist have difficulties in fully exploiting the potential of standards that are often notoriously complex, lack non-technical documentations, and use different representations and underlying technologies. In the last few years, a series of initiatives such as Scratchpads, the EDIT Platform for Cybertaxonomy, and biowikifarm have started to implement and set up virtual work platforms for biodiversity sciences which shield their users from the complexity of the underlying standards. Apart from being practical work-horses for numerous working processes related to biodiversity sciences, they can be seen as information brokers mediating information between multiple data standards and protocols. The ViBRANT project will further strengthen the flexibility and power of virtual biodiversity working platforms by building software interfaces between them, thus facilitating essential information flows needed for comprehensive data exchange, data indexing, web-publication, and versioning. This work will make an important contribution to the shaping of an international, interoperable, and user-oriented biodiversity information infrastructure.

  8. Cytostretch, an Organ-on-Chip Platform

    Directory of Open Access Journals (Sweden)

    Nikolas Gaio

    2016-07-01

    Full Text Available Organ-on-Chips (OOCs are micro-fabricated devices which are used to culture cells in order to mimic functional units of human organs. The devices are designed to simulate the physiological environment of tissues in vivo. Cells in some types of OOCs can be stimulated in situ by electrical and/or mechanical actuators. These actuations can mimic physiological conditions in real tissue and may include fluid or air flow, or cyclic stretch and strain as they occur in the lung and heart. These conditions similarly affect cultured cells and may influence their ability to respond appropriately to physiological or pathological stimuli. To date, most focus has been on devices specifically designed to culture just one functional unit of a specific organ: lung alveoli, kidney nephrons or blood vessels, for example. In contrast, the modular Cytostretch membrane platform described here allows OOCs to be customized to different OOC applications. The platform utilizes silicon-based micro-fabrication techniques that allow low-cost, high-volume manufacturing. We describe the platform concept and its modules developed to date. Membrane variants include membranes with (i through-membrane pores that allow biological signaling molecules to pass between two different tissue compartments; (ii a stretchable micro-electrode array for electrical monitoring and stimulation; (iii micro-patterning to promote cell alignment; and (iv strain gauges to measure changes in substrate stress. This paper presents the fabrication and the proof of functionality for each module of the Cytostretch membrane. The assessment of each additional module demonstrate that a wide range of OOCs can be achieved.

  9. Analysis and Application for Integrity Model on Trusted Platform

    Institute of Scientific and Technical Information of China (English)

    TU Guo-qing; ZHANG Huan-guo; WANG Li-na; YU Dan-dan

    2005-01-01

    To build a trusted platform based on Trusted Computing Platform Alliance (TCPA) ' s recommendation,we analyze the integrity mechanism for such a PC platform in this paper. By combinning access control model with information flow model, we put forward a combined process-based lattice model to enforce security. This model creates a trust chain by which we can manage a series of processes from a core root of trust module to some other application modules.In the model, once the trust chain is created and managed correctly,the integrity of the computer's hardware and sofware has been mainfained, so does the confidentiality and authenticity. Moreover, a relevant implementation of the model is explained.

  10. Stratifying the Develoment of Product Platforms

    DEFF Research Database (Denmark)

    Sköld, Martin; Karlsson, Christer

    2013-01-01

    companies develop platforms for different aims, purposes, and product scopes. Following on from this, the requirements for platform development resources, the ways of organizing platform development, and the implications for management styles have not been explored and are presumably varying. To start...... influencing the project length, requirements for platform development resources, principles for organizing, and implications for management styles....

  11. New offshore platform in the Mexican Gulf

    Energy Technology Data Exchange (ETDEWEB)

    Beisel, T.

    1982-04-01

    After a construction period of only 10 months, the second steel Offshore platform was recently completed in the Mexican Gulf. The pattern for this structure was the Cognac platform. The erection of the new platform, called the 'Cerveza' platform, is described in the article.

  12. Centrifuge-Based Fluidic Platforms

    Science.gov (United States)

    Zoval, Jim; Jia, Guangyao; Kido, Horacio; Kim, Jitae; Kim, Nahui; Madou, Marc

    In this chapter centrifuge-based microfluidic platforms are reviewed and compared with other popular microfluidic propulsion methods. The underlying physical principles of centrifugal pumping in microfluidic systems are presented and the various centrifuge fluidic functions such as valving, decanting, calibration, mixing, metering, heating, sample splitting, and separation are introduced. Those fluidic functions have been combined with analytical measurements techniques such as optical imaging, absorbance and fluorescence spectroscopy and mass spectrometry to make the centrifugal platform a powerful solution for medical and clinical diagnostics and high-throughput screening (HTS) in drug discovery. Applications of a compact disc (CD)-based centrifuge platform analyzed in this review include: two-point calibration of an optode-based ion sensor, an automated immunoassay platform, multiple parallel screening assays and cellular-based assays. The use of modified commercial CD drives for high-resolution optical imaging is discussed as well. From a broader perspective, we compare the technical barriers involved in applying microfluidics for sensing and diagnostic as opposed to applying such techniques to HTS. The latter poses less challenges and explains why HTS products based on a CD fluidic platform are already commercially available, while we might have to wait longer to see commercial CD-based diagnostics.

  13. Platforms for Innovation and Internationalization

    Directory of Open Access Journals (Sweden)

    Erik Stavnsager Rasmussen

    2017-05-01

    Full Text Available The high-tech global startup has many challenges related to both innovation and internationalization. From a Danish cluster of Welfare Tech firms, eight innovative and international firms were selected and interviewed. Such firms typically have to be agile and operate in virtual networks in almost all parts of their value chains. This article contributes to the understanding of how innovation and internationalization to a great extent are interlinked. The firms have developed a core product or service offering, which the firms often describe as “a platform”. Around the platform, they develop their products and services for new customers and users in new countries. The firms have to sustain a strong focus on the platform while at the same time developing their platform solution for new products, new customers, and new markets. This pivoting makes it possible to use the platform in a new context but is highly demanding for the firms. They need to be extremely agile and fast-moving but at the same time still to have a focus on the core of the firm: the platform.

  14. A Droplet Microfluidic Platform for Automating Genetic Engineering.

    Science.gov (United States)

    Gach, Philip C; Shih, Steve C C; Sustarich, Jess; Keasling, Jay D; Hillson, Nathan J; Adams, Paul D; Singh, Anup K

    2016-05-20

    We present a water-in-oil droplet microfluidic platform for transformation, culture and expression of recombinant proteins in multiple host organisms including bacteria, yeast and fungi. The platform consists of a hybrid digital microfluidic/channel-based droplet chip with integrated temperature control to allow complete automation and integration of plasmid addition, heat-shock transformation, addition of selection medium, culture, and protein expression. The microfluidic format permitted significant reduction in consumption (100-fold) of expensive reagents such as DNA and enzymes compared to the benchtop method. The chip contains a channel to continuously replenish oil to the culture chamber to provide a fresh supply of oxygen to the cells for long-term (∼5 days) cell culture. The flow channel also replenished oil lost to evaporation and increased the number of droplets that could be processed and cultured. The platform was validated by transforming several plasmids into Escherichia coli including plasmids containing genes for fluorescent proteins GFP, BFP and RFP; plasmids with selectable markers for ampicillin or kanamycin resistance; and a Golden Gate DNA assembly reaction. We also demonstrate the applicability of this platform for transformation in widely used eukaryotic organisms such as Saccharomyces cerevisiae and Aspergillus niger. Duration and temperatures of the microfluidic heat-shock procedures were optimized to yield transformation efficiencies comparable to those obtained by benchtop methods with a throughput up to 6 droplets/min. The proposed platform offers potential for automation of molecular biology experiments significantly reducing cost, time and variability while improving throughput.

  15. Development of integrated platform for computational material design

    Energy Technology Data Exchange (ETDEWEB)

    Kiyoshi, Matsubara; Kumi, Itai; Nobutaka, Nishikawa; Akifumi, Kato [Center for Computational Science and Engineering, Fuji Research Institute Corporation (Japan); Hideaki, Koike [Advance Soft Corporation (Japan)

    2003-07-01

    The goal of our project is to design and develop a problem-solving environment (PSE) that will help computational scientists and engineers develop large complicated application software and simulate complex phenomena by using networking and parallel computing. The integrated platform, which is designed for PSE in the Japanese national project of Frontier Simulation Software for Industrial Science, is defined by supporting the entire range of problem solving activity from program formulation and data setup to numerical simulation, data management, and visualization. A special feature of our integrated platform is based on a new architecture called TASK FLOW. It integrates the computational resources such as hardware and software on the network and supports complex and large-scale simulation. This concept is applied to computational material design and the project 'comprehensive research for modeling, analysis, control, and design of large-scale complex system considering properties of human being'. Moreover this system will provide the best solution for developing large and complicated software and simulating complex and large-scaled phenomena in computational science and engineering. A prototype has already been developed and the validation and verification of an integrated platform will be scheduled by using the prototype in 2003. In the validation and verification, fluid-structure coupling analysis system for designing an industrial machine will be developed on the integrated platform. As other examples of validation and verification, integrated platform for quantum chemistry and bio-mechanical system are planned.

  16. Persistent Monitoring Platforms Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Bennett, C L

    2007-02-22

    This project was inspired and motivated by the need to provide better platforms for persistent surveillance. In the years since the inception of this work, the need for persistence of surveillance platforms has become even more widely appreciated, both within the defense community and the intelligence community. One of the most demanding technical requirements for such a platform involves the power plant and energy storage system, and this project concentrated almost exclusively on the technology associated with this system for a solar powered, high altitude, unmanned aircraft. An important realization for the feasibility of such solar powered aircraft, made at the outset of this project, was that thermal energy may be stored with higher specific energy density than for any other known practical form of rechargeable energy storage. This approach has proved to be extraordinarily fruitful, and a large number of spin-off applications of this technology were developed in the course of this project.

  17. Cerveza platforms offer economic options

    Energy Technology Data Exchange (ETDEWEB)

    Leblanc, L.A.

    1982-08-01

    Two single-piece platforms, Cerveze and Cerveza Ligera, were installed by Union Oil Co. in 925-935 ft of water. The technology and equipment used for the two platforms can be used for units to a depth of 1,400 ft in mild climates and to 1,000 ft in more critical weather areas such as the North Sea. The significant improvements in design and procedures in the construction and installation of the Cerveza Ligera platform are: (1) four leg structure, as opposed to eight, requiring less steel; (2) simplified fabrication; and (3) quicker installation. The most significant area of improvement in the Ligera project compared with Cerveza was in communications. Communications between naval architects and onshore launch foremen during loadout, and between surveyors and tug captains during positioning, are cited as examples.

  18. Tax Responses in Platform Industries

    DEFF Research Database (Denmark)

    Kind, Hans Jarle; Köthenbürger, Marko; Schjelderup, Guttorm

    Two-sided platform firms serve distinct customer groups that are connected through interdependent demand, and include major businesses such as the media industry, banking, and the software industry. A well known result of tax incidence is that consumers of a more heavily taxed good pay a higher...... price and thus buy less of the good. The present paper shows that this result need not hold in a two-sided market. On the contrary, a higher ad valorem tax may lower end-user prices and spur sales. Thus, two-sided platform firms may not at all engage in tax shifting via price increases. We further show...

  19. Moodle vs. Social Media Platforms

    DEFF Research Database (Denmark)

    Gulieva, Valeria

    Given the competition coming from various social media platforms, it is explored in this paper how students could be encouraged to use Moodle more proactively during their studies. Moodle is a course management system for online learning. It is designed to be a flexible template-based system, which......, known and widely used social platforms. It might be also due to the fact that students do not see the benefits in investing time and efforts in learning the new system. Another reason might be the mandatory nature of Moodle, i.e., it is imposed on students, rather than a free choice – and this might...

  20. A practice scaffolding interactive platform

    DEFF Research Database (Denmark)

    Bundsgaard, Jeppe

    2009-01-01

    , structures the students' activity, and interactively supports subject learning. A PracSIP facilitates students' development of complex competencies, and at the same time it supports the students' development of skills defined in the curriculum. The paper introduces the concept, presents the theoretical......A Practice Scaffolding Interactive Platform (PracSIP) is a social learning platform which supports students in collaborative project based learning by simulating a professional practice. A PracSIP puts the core tools of the simulated practice at the students' disposal, it organizes collaboration...

  1. An electrochemical-cantilever platform for hybrid sensing applications

    DEFF Research Database (Denmark)

    Fischer, Lee MacKenzie; Dohn, Søren; Boisen, Anja

    2011-01-01

    This work presents a fully-functional, microfabricated electrochemical-cantilever hybrid platform with flow control. A new cantilever chip format is designed, fabricated, and mounted in a custom polymer flow cell. Issues such as leakage and optical/electrical access are addressed, and combined me...... mechanical and electrochemical performance is investigated. Lastly, a cantilever is “defunctionalized” in situ to create a reference cantilever for differential measurements in detection of Cu2+ ions at concentrations of 10 μM and 100 nM....

  2. Determination of Epichlorohydrin in Water by Purge and Trap/Gas Chromatography-Mass Spectrometry%吹扫捕集/气相色谱-质谱联用法测定水中环氧氯丙烷

    Institute of Scientific and Technical Information of China (English)

    张芹; 陈科平; 王少青

    2015-01-01

    A method for determination of epichlorohydrin was established based on purge and trap / gas chromatography mass spectrometry. The purge temperature, purge time, desorption temperature and desorption time were adjusted ,the efficiency of purge and trap affected by purge and trap conditions was analyzed, and the best purge and trap condition were determined. Under the optimized conditions, the correlation coefficients of epichlorohydrin were 0.999 9, the average recoveries were 99.7%, and the relative standard deviations of method were 3.0%; the detection limits of method were 0.10 μg/L. Compared with the national standard method, this method takes advantages of easy to operation, the linear relations, accuracy and precision were well. The method can meet the requirements for the determination of epichlorohydrin in surface water and drinking water.%建立吹扫捕集/气相色谱-质谱法(GC-MS)测定水中环氧氯丙烷的方法。通过对吹扫捕集条件进行调整,讨论吹扫温度和吹扫时间、解吸温度和解吸时间对吹扫捕集效率的影响,确定最佳吹扫捕集条件。结果表明,在最佳条件下,环氧氯丙烷的线性相关系数为0.9999,平均加标回收率为99.7%,相对标准偏差为3.0%;方法检出限为0.10μg/L。该方法与国家标准方法相比,操作简便、检出限低、准确度和精密度高,适用于地表水和生活饮用水中环氧氯丙烷的分析测定。

  3. 2009 Analysis Platform Review Report

    Energy Technology Data Exchange (ETDEWEB)

    Ferrell, John [Office of Energy Efficiency and Renewable Energy (EERE), Washington, DC (United States

    2009-12-01

    This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the U.S. Department of Energy Biomass Program’s Analysis platform review meeting, held on February 18, 2009, at the Marriott Residence Inn, National Harbor, Maryland.

  4. 2009 Infrastructure Platform Review Report

    Energy Technology Data Exchange (ETDEWEB)

    Ferrell, John [Office of Energy Efficiency and Renewable Energy (EERE), Washington, DC (United States)

    2009-12-01

    This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the U.S. Department of Energy Biomass program‘s Infrastructure platform review meeting, held on February 19, 2009, at the Marriott Residence Inn, National Harbor, Maryland.

  5. Venus Atmospheric Maneuverable Platform (VAMP)

    Science.gov (United States)

    Polidan, R.; Lee, G.; Sokol, D.; Griffin, K.; Bolisay, L.

    2014-05-01

    VAMP is a long lived, semi-buoyant, atmospheric “rover” that deploys in orbit, enters the Venus atmosphere and flies in the Venus atmosphere between 55 and 70 km for up to one year as a platform to address VEXAG goals I.A, I.B, and I.C.

  6. Utilizing platforms in industrialized construction

    DEFF Research Database (Denmark)

    Bonev, Martin; Wörösch, Michael; Hvam, Lars

    2015-01-01

    Purpose – The purpose of this paper is to explore the development of a platform-based projectexecution in the industrialised construction sector, with a focus on systematically balancing cost andvalue. Offering custom-tailored buildings at reasonable costs has been a growing concern for manyconst...

  7. Generational Transitions in Platform Markets

    DEFF Research Database (Denmark)

    Kretschmer, Tobias; Claussen, Jörg

    2016-01-01

    The introduction of a new product generation forces incumbents in platform markets to rebuild their installed base of complementary products. Using three different data sets on the U.S. market for video game consoles, we show that incumbents can, to some extent, substitute for rebuilding their new...

  8. Analysis of offshore jacket platform

    Digital Repository Service at National Institute of Oceanography (India)

    Harish, N.; Mandal, S.; Shanthala, B.; Rao, S.

    -Rohman, M., ‘Multi-loop feedback control of offshore steel jacket platforms’, Computers & Structures 70, 1999, 185–202. 11.Yamamoto, I., Terada, Y., and Yokokura, K., ‘An application of a position keeping control system to floating offshore platform...

  9. Tax Responses in Platform Industries

    DEFF Research Database (Denmark)

    Kind, Hans Jarle; Köthenbürger, Marko; Schjelderup, Guttorm

    Two-sided platform firms serve distinct customer groups that are connected through interdependent demand, and include major businesses such as the media industry, banking, and the software industry. A well known result of tax incidence is that consumers of a more heavily taxed good pay a higher...

  10. 2009 Feedstocks Platform Review Report

    Energy Technology Data Exchange (ETDEWEB)

    Ferrell, John [Office of Energy Efficiency and Renewable Energy (EERE), Washington, DC (United States)

    2009-12-01

    This document summarizes the recommendations and evaluations provided by an independent external panel of experts at the U.S. Department of Energy Biomass Program‘s Feedstock platform review meeting, held on April 8–10, 2009, at the Grand Hyatt Washington, Washington, D.C.

  11. In vivo magnetic enrichment, photoacoustic diagnosis, and photothermal purging of infected blood using multifunctional gold and magnetic nanoparticles.

    Directory of Open Access Journals (Sweden)

    Ekaterina I Galanzha

    Full Text Available Bacterial infections are a primary cause of morbidity and mortality worldwide. Bacteremia is a particular concern owing to the possibility of septic shock and the development of metastatic infections. Treatment of bacteremia is increasingly compromised by the emergence of antibiotic resistant strains, creating an urgent need for alternative therapy. Here, we introduce a method for in vivo photoacoustic (PA detection and photothermal (PT eradication of Staphylococcus aureus in tissue and blood. We show that this method could be applicable for label-free diagnosis and treatment of in the bloodstream using intrinsic near-infrared absorption of endogenous carotenoids with nonlinear PA and PT contrast enhancement. To improve sensitivity and specificity for detection of circulating bacteria cells (CBCs, two-color gold and multilayer magnetic nanoparticles with giant amplifications of PA and PT contrasts were functionalized with an antibody cocktail for molecular targeting of S. aureus surface-associated markers such as protein A and lipoprotein. With a murine model, the utility of this approach was demonstrated for ultrasensitive detection of CBCs with threshold sensitivity as low as 0.5 CBCs/mL, in vivo magnetic enrichment of CBCs, PT eradication of CBCs, and real-time monitoring of therapeutic efficacy by CBC counting. Our PA-PT nano-theranostic platform, which integrates in vivo multiplex targeting, magnetic enrichment, signal amplification, multicolor recognition, and feedback control, could be used as a biological tool to gain insights on dissemination pathways of CBCs, infection progression by bacteria re-seeding, and sepsis development and treatment, and could potentially be feasible in humans, especially using bypass schematic.

  12. Toxicity to the normal hemocytes by ALA-PDT for the ex vivo purging of hematopoietic stem cell grafts

    Institute of Scientific and Technical Information of China (English)

    Zhang Baoqin; Zhang Zhenxi; Miao Lixia; Tan Lu; Xiao Mi; Xu Xia

    2008-01-01

    Objective To study the toxic effects of 5-amionlevulinic acid-based photodynamic therapy (ALA-PDT) on human peripheral blood mononuclear cells (PBMCs), cord blood mononuclear cells (CBMCs) and peripheral blood stem cells (PBSCs), and furthermore, to understand the possible causes of this response. Methods We used MTT assay to detect the survival rate of PBMCs, CBMCs and PBSCs after treated by ALA-PDT under the optimum experiment conditions with U937 as control;Annexin V-FITC/PI was used to detect the pattern of cell death induced by ALA-PDT. By using flow cytometry, we detected intracellular PpIX fluorescence intensity. Results After ALA-PDT treatment the survival rate of PBMCs had no significant change;however in PBSCs and CBMCs, the survival rate reduced to 70%, and the survival rate of leukemia cell U937 was the lowest, about 30%. After incubation with ALA,except for PBMCs, intraceUuiar PplX fluorescence intensity of the other two kinds of normal haemocytes and U937 increased obviously. These results combined with the flow cytometry suggested that the main pattern of cell death here was apoptosts. Conclusion Under the optimum experiment conditions, ALA-PDT has a slight effect on normal haemocytes but excellent depletions of leukemia cells. Therefore, it can effectively purify autologons bone marrow or stem cell grafts.

  13. Application of Stable-pressure Steam Purging Technology in 660MW Supercritical Once--through Boiler%660MW超临界机组稳压吹管的实践

    Institute of Scientific and Technical Information of China (English)

    郭刚; 邢燕

    2011-01-01

    Combining with the engineering practice of stable-pressure steam purging in 660 MW supercritical once-through boiler,and calculating the steam purging parameters, the application was analyzed in some aspects including parameter selection ,parameter contro%通过对超临界机组的吹管参数的计算,结合稳压吹管的实践,从吹管参数的选择、吹管过程中参数的控制以及系统的变更等几个方面进行了分析总结,对超临界机组的吹管具有一定的借鉴意义。

  14. Hydraulic Calculation and Purging Coefficient Determination for High Pressure Steam Network%高压蒸汽管网的水力学计算及吹扫参数确定

    Institute of Scientific and Technical Information of China (English)

    袁良正; 贾金洁

    2016-01-01

    Exampled with a large scale of coal-to-natural gas plant, hydraulic and purging parameters for high pressure and superheated steam pipe network were studied in this article. By using chemical process simulation software ASPEN HYSIS, the model of steam pipeline net was established and then it was calculated, with which the method based on quantitative analysis for calculating steam purging parameters was found.%以某大型煤制天然气项目为例,对高压过热蒸汽管网的水力学及吹扫参数进行研究。采用化工流程模拟软件ASPEN HYSYS对蒸汽管网进行建模计算,找到了一种定量分析计算蒸汽吹扫参数的方法。

  15. Theory of Spleen and Stomach Purging Method of Acupuncture for Treatment of Simple Obesity%补脾泻胃针灸法治疗单纯性肥胖症的理论初探

    Institute of Scientific and Technical Information of China (English)

    张君; 邵素菊; 高希言

    2013-01-01

    目的:探讨针灸补脾泻胃法治疗单纯性肥胖症的理论依据.方法:从引起单纯性肥胖症的病因病机、脾胃的生理病理特点、中医对单纯肥胖的认识等方面来阐述针灸补脾泻胃法治疗单纯性肥胖症的理论依据.结果:补脾泻胃法治疗单纯性肥胖是通过不同的补泻方法来刺激特定的经络腧穴,以平衡阴阳、调理脏腑、运行气血、疏通经络,从而达到减肥、降脂的目的.结论:针灸治疗单纯性肥胖症可以采用补脾泻胃法.%Objective:To explore the theoretical basis for acupuncture invigorating the spleen stomach purging method for treatment of simple obesity. Methods:Theoretical basis of spleen stomach purging method of acupuncture for the treatment of simple obesity were explained from the aspects of the etiology and pathology caused by obesity, physiological and pathological characteristics of spleen and stomach, and Chinese medicine for the understanding of simple obesity. Results:The spleen and stomach purging method in the treatment of simple obesity, to stimulate the main and collateral channels acupoint specific by reinforcing and reducing method of different, with the balance of yin and yang, regulating zangfu,run blood,dredge main and collateral channel,so as to achieve weight loss purposes , lipid-lowering. Conclusion: Spleen stomach purging method of acupuncture for treatment of simple obesity.

  16. Gas Purge Microextraction Coupled with Stable Isotope Labeling-Liquid Chromatography/Mass Spectrometry for the Analysis of Bromophenols in Aquatic Products.

    Science.gov (United States)

    Zhang, Shijuan; Yu, Qiuhui; Sheng, Cuncun; You, Jinmao

    2016-12-14

    A green, sensitive, and accurate method was developed for the extraction and determination of bromophenols (BPs) from aquatic products by using organic solvent-free gas purge microsyringe extraction (GP-MSE) technique in combination with stable isotope labeling (SIL) strategy. BPs were extracted by NaHCO3 buffer solution, with recoveries varying from 92.0% to 98.5%. The extracted solution was analyzed by SIL strategy, during which analytes and standards were labeled by 10-methyl-acridone-2-sulfonyl chloride (d0-MASC) and its deuterated counterpart d3-MASC, respectively. The labeling reaction was finished within 10 min with good stability. The liquid chromatography-tandem mass spectrometry (HPLC-MS/MS) sensitivity of BPs was greatly enhanced due to the mass-enhancing property of MASC, while the matrix effect was effectively minimized by the SIL strategy. The limits of detection (LODs) were in the range of 0.10-0.30 μg/kg, while the limits of quantitations (LOQs) were in the range of 0.32-1.0 μg/kg. The proposed method also showed great potential in the qualitative analysis of other bromophenols in the absence of standard.

  17. Fracture behavior and microstructure analysis of Al2O3-MgO-CaO castables for steel-ladle purging plugs

    Institute of Scientific and Technical Information of China (English)

    Bin Long; Gui-ying Xu; Yong Li; Andreas Buhr

    2016-01-01

    Three different castables based on the Al2O3–MgO–CaO system were prepared as steel-ladle purging plug refractories: corun-dum-based low-cement castable (C-LCC), corundum-spinel-based low-cement castable (C-S-LCC), and corundum-spinel no-cement casta-ble (C-S-NCC) (hydratable alumina (ρ-Al2O3) bonded). The fracture behavior at room temperature was tested by the method of “wedge-splitting” on samples pre-fired at different temperatures; the specific fracture energyG′f and notched tensile strengthσNT were ob-tained from these tests. In addition, the Young’s modulusE was measured by the method of resonance frequency of damping analysis (RFDA). The thermal stress resistance parameterR′′ calculated using the values ofG′f,σNT, andE was used to evaluate the thermal shock resistance of the materials. According to the microstructure analysis results, the sintering effect and the bonding type of the matrix material were different among these three castables, which explains their different fracture behaviors.

  18. Fracture behavior and microstructure analysis of Al2O3-MgO-CaO castables for steel-ladle purging plugs

    Science.gov (United States)

    Long, Bin; Xu, Gui-ying; Li, Yong; Buhr, Andreas

    2016-11-01

    Three different castables based on the Al2O3-MgO-CaO system were prepared as steel-ladle purging plug refractories: corundum- based low-cement castable (C-LCC), corundum-spinel-based low-cement castable (C-S-LCC), and corundum-spinel no-cement castable (C-S-NCC) (hydratable alumina (ρ-Al2O3) bonded). The fracture behavior at room temperature was tested by the method of "wedge-splitting" on samples pre-fired at different temperatures; the specific fracture energy G f ' and notched tensile strength σNT were obtained from these tests. In addition, the Young's modulus E was measured by the method of resonance frequency of damping analysis (RFDA). The thermal stress resistance parameter R'''' calculated using the values of G f ' , σ NT, and E was used to evaluate the thermal shock resistance of the materials. According to the microstructure analysis results, the sintering effect and the bonding type of the matrix material were different among these three castables, which explains their different fracture behaviors.

  19. Comparison of obese and nonobese individuals with binge eating disorder: delicate boundary between binge eating disorder and non-purging bulimia nervosa.

    Science.gov (United States)

    Carrard, Isabelle; Van der Linden, Martial; Golay, Alain

    2012-09-01

    To compare obese and nonobese individuals with binge eating disorder (BED) on demographic data, illness history, eating disorders and psychological health. This study used baseline data from a randomized controlled study on the efficacy of an online cognitive behavioural self-help treatment. Seventy-four women aged between 18 and 60 years were recruited in the community. They had to meet full or subthreshold diagnostic criteria for BED according to Diagnostic and Statistical Manual of Mental Disorders, Fourth Edition. Forty per cent of the sample had a body mass index higher than 30 kg/m(2) . Mean age and severity of eating disorders were similar between obese and nonobese individuals. A statistically significant difference emerged regarding dietary restraint, with nonobese BED individuals exhibiting higher scores than obese BED individuals. Dietary restraint might be one of the factors explaining body mass index differences among BED individuals. This raises the question of the boundary between non-purging bulimia nervosa and BED in nonobese people. Copyright © 2012 John Wiley & Sons, Ltd and Eating Disorders Association.

  20. Simultaneous Determination of Acetaldehyde,Acrolein,Acrylonitrile and Pyridine in Water by Purge-and-trap-Gas Chromatography-Mass Spectrometry%吹扫捕集-气相色谱/质谱法测定水中的乙醛、丙烯醛、丙烯腈和吡啶

    Institute of Scientific and Technical Information of China (English)

    许家慧; 普学伟; 施艳峰; 觉玉峰

    2015-01-01

    水中的乙醛、丙烯醛、丙烯腈和吡啶经吹扫捕集、解吸后,用HP-VOC毛细管色谱柱进行GC分离,用GC-MS法选择离子模式( SIM)下进行检测,外标法定量。结果表明,选择取样量25 mL,吹扫流量为40 mL/min,吹扫温度为40℃,吹扫时间为15 min,解吸时间为2 min,解吸温度为200℃,烘焙时间20 min,乙醛和吡啶质量浓度在0.025~0.60 mg/L之间,丙烯醛和丙烯腈质量浓度在0.0025~0.10 mg/L之间时,校准曲线呈线性关系,相关系数r>0.995,乙醛、丙烯醛、丙烯腈和吡啶的方法检出限分别为0.0016,0.0013,0.0005和0.0021 mg/L。对3个不同浓度样品进行空白加标实验,测量的回收率为87.8%~114.3%,相对标准偏差(n=6)为2.51%~10.4%。对3批实际水样进行分析,其中一个废水水样加标回收率为79.2%~103.8%,相对标准偏差(n=6)为3.04%~6.39%。%A method for simultaneous determination of acetaldehyde,acrolein,acrylonitrile and pyridine in water by purge-and-trap-gas chromatography-mass spectrometry ( GC-MS) was reported.These compounds were concentrated by purging and trapping fol-lowed by desorption before GC-MS measurement using the HP-VOC capillary column for separation and selective ion mode ( SIM) for MS detection.External calibration was used for quantification.The following experimental conditions were used:the sampling vol-ume was 25 mL,purging gas flow was 40 mL/min,purging temperature was 40 ℃,purging time was 15 min,desorption time was 2 min,desorption temperature was 200℃,and baking time was 20 min.Under this condition,it was determined that the concentrations of acetaldehyde and pyridine were between 0.025 and 0.60 mg/L,and acrolein and acrylonitrile were between 0.002 5 and 0.10 mg/L.The calibration curve showed good linearity with the correlation coefficient r>0.995.The method detection limits of acetalde

  1. Long-Term Remission of Primary Bone Marrow Diffuse Large B-Cell Lymphoma Treated with High-Dose Chemotherapy Rescued by In Vivo Rituximab-Purged Autologous Stem Cells

    Directory of Open Access Journals (Sweden)

    Hiroshi Kazama

    2012-01-01

    Full Text Available Primary bone marrow diffuse large B-cell lymphoma (DLBCL is a rare type of extranodal lymphoma with poor prognosis. Here, we report a case of primary bone marrow DLBCL successfully treated with high-dose chemotherapy and rescued by in vivo rituximab-purged autologous stem cells. A 39-year-old woman visited our hospital because of anemia. Bone marrow examination revealed a large B-cell lymphoma invasion. An 18F-fluorodeoxyglucose positron emission tomography scan revealed disseminated bone marrow uptake without evidence of dissemination at other sites. These findings led to a diagnosis of primary bone marrow DLBCL. Our patient underwent R-CHOP (rituximab, cyclophosphamide, doxorubicin, vincristine, and prednisolone chemotherapy and achieved complete remission. Subsequently, she received high-dose chemotherapy with an in vivo rituximab-purged autologous stem cell transplant. Seven years have passed since the transplantation, and she remains in remission. This suggests that transplantation of an in vivo rituximab-purged autograft is a promising strategy for primary bone marrow DLBCL.

  2. 通腑泻实推拿法治疗小儿实证便秘疗效观察%Efficacy Observation on Massage of Dredging and Purging Treating Children with Constipation of Excess Syndrome

    Institute of Scientific and Technical Information of China (English)

    利玉婷; 陈红蕾

    2014-01-01

    目的:观察通腑泻实推拿法治疗小儿实证便秘的临床疗效。方法:55例实秘患儿采取通腑泻实推拿法治疗,每日1次,5次为一疗程,2个疗程后观察疗效。结果:治愈39例,好转14例,无效2例,总有效率达96.5%。结论:通腑泻实推拿法治疗小儿实秘临床疗效确切,值得推广。%To observe the clinical efficacy in massage of dredging and purging treating children with constipation of excess syndrome. Methods:55 cases of sthenia constipation adopted massage of dredging and purging, 1 time per day, 5 times for a course of treatment, the therapeutic effect was observed after 2 courses of treatment. Results:39 cases were cured, 14 cases improved, 2 cases ineffective, the total effective rate was 96.5%. Conclusion:Massage of dredging and purging treating children with constipation of excess syndrome is clinically quite effective, being worth of promoting.

  3. Product Platform Development in Industrial Networks

    DEFF Research Database (Denmark)

    Karlsson, Christer; Skold, Martin

    2011-01-01

    The article examines the strategic issues involved in the deployment of product platform development in an industrial network. The move entails identifying the types and characteristics of generically different product platform strategies and clarifying strategic motives and differences. Number...

  4. Parametric modelling of nonstationary platform deck motions

    Digital Repository Service at National Institute of Oceanography (India)

    Mandal, S.

    -sense-stationary processes. Then the time series are modelled by the maximum entropy method which is formulated here for spectral estimation of platform deck displacements. The lower order maximum entropy spectra of nonstationary platform deck displacements are compared...

  5. Front-end conceptual platform modeling

    DEFF Research Database (Denmark)

    Guðlaugsson, Tómas Vignir; Ravn, Poul Martin; Mortensen, Niels Henrik

    2014-01-01

    Platform thinking has been the subject of investigation and deployment in many projects in both academia and industry. Most contributions involve the restructuring of product programs, and only a few support front-end development of a new platform in parallel with technology development....... This contribution deals with the development of product platforms in front-end projects and introduces a modeling tool: the Conceptual Product Platform model. State of the art within platform modeling forms the base of a modeling formalism for a Conceptual Product Platform model. The modeling formalism is explored...... through an example and applied in a case in which the Conceptual Product Platform model has supported the front-end development of a platform for an electro-active polymer technology. The case describes the contents of the model and how its application supported the development work in the project...

  6. The Logic of Digital Platform Disruption

    DEFF Research Database (Denmark)

    Kazan, Erol; Tan, Chee-Wee; Lim, Eric T. K.

    Digital platforms are disruptive IT artifacts, because they facilitate the quick release of innovative platform derivatives from third parties (e.g., apps). This study endeavours to unravel the disruptive potential, caused by distinct designs and configurations of digital platforms on market...... environments. We postulate that the disruptive potential of digital platforms is determined by the degree of alignment among the business, technology and platform profiles. Furthermore, we argue that the design and configuration of the aforementioned three elements dictates the extent to which open innovation...... is permitted. To shed light on the disruptive potential of digital platforms, we opted for payment platforms as our unit of analysis. Through interviews with experts and payment providers, we seek to gain an in-depth appreciation of how contemporary digital payment platforms are designed and configured...

  7. Modeling and analysis of offshore jacket platform

    Digital Repository Service at National Institute of Oceanography (India)

    Mohan, P.; Sidhaarth, K.R.A.; SanilKumar, V.

    This paper details the results obtained from static analysis, considering both operational and ultimate limit state performance characteristics of a jacket platform, designed at Mumbai high basin. The existing platforms at Mumbai high region...

  8. The Logic of Digital Platform Disruption

    DEFF Research Database (Denmark)

    Kazan, Erol; Tan, Chee-Wee; Lim, Eric T. K.

    Digital platforms are disruptive IT artifacts, because they facilitate the quick release of innovative platform derivatives from third parties (e.g., apps). This study endeavours to unravel the disruptive potential, caused by distinct designs and configurations of digital platforms on market...... environments. We postulate that the disruptive potential of digital platforms is determined by the degree of alignment among the business, technology and platform profiles. Furthermore, we argue that the design and configuration of the aforementioned three elements dictates the extent to which open innovation...... is permitted. To shed light on the disruptive potential of digital platforms, we opted for payment platforms as our unit of analysis. Through interviews with experts and payment providers, we seek to gain an in-depth appreciation of how contemporary digital payment platforms are designed and configured...

  9. Product Platform Development in Industrial Networks

    DEFF Research Database (Denmark)

    Karlsson, Christer; Skold, Martin

    2011-01-01

    The article examines the strategic issues involved in the deployment of product platform development in an industrial network. The move entails identifying the types and characteristics of generically different product platform strategies and clarifying strategic motives and differences. Number...

  10. Software development on the SAP HANA platform

    CERN Document Server

    Walker, Mark

    2013-01-01

    Software Development on the SAP HANA Platform is a general tutorial guide to SAP HANA.This book is written for beginners to the SAP HANA platform. No knowledge of SAP HANA is necessary to start using this book.

  11. Hierarchical DSE for multi-ASIP platforms

    DEFF Research Database (Denmark)

    Micconi, Laura; Corvino, Rosilde; Gangadharan, Deepak;

    2013-01-01

    This work proposes a hierarchical Design Space Exploration (DSE) for the design of multi-processor platforms targeted to specific applications with strict timing and area constraints. In particular, it considers platforms integrating multiple Application Specific Instruction Set Processors (ASIPs...

  12. A Platform for Spreadsheet Composition

    CERN Document Server

    Baglietto, Pierpaolo; Mangiante, Simone; Maresca, Massimo; Parodi, Andrea; Stecca, Michele

    2011-01-01

    A huge amount of data is everyday managed in large organizations in many critical business sectors with the support of spreadsheet applications. The process of elaborating spreadsheet data is often performed in a distributed, collaborative way, where many actors enter data belonging to their local business domain to contribute to a global business view. The manual fusion of such data may lead to errors in copy-paste operations, loss of alignment and coherency due to multiple spreadsheet copies in circulation, as well as loss of data due to broken cross-spreadsheet links. In this paper we describe a methodology, based on a Spreadsheet Composition Platform, which greatly reduces these risks. The proposed platform seamlessly integrates the distributed spreadsheet elaboration, supports the commonly known spreadsheet tools for data processing and helps organizations to adopt a more controlled and secure environment for data fusion.

  13. Platform-Independent Courseware Sharing

    Directory of Open Access Journals (Sweden)

    Takao Shimomura

    2013-04-01

    Full Text Available Courseware distribution between different platforms is the major issue of current e-Learning. SCORM (Sharable Content Object Reference Model is one of the solutions for courseware sharing. However, to make SCORM-conformable courseware, some knowledge about HTML and JavaScript is required. This paper presents a SWF (Sharable Web Fragment-based e-Learning system, where courseware is created with sharable Web fragments such as Web pages, images and other resources, and the courseware can be distributed to another platform by export and import facilities. It also demonstrates how to export a subject that contains assignments and problems and how to import the whole subject, only the assignments, or only the problems. The exported meta-information is architecture-independent and provides a model of courseware distribution.

  14. Stabilisation problem in biaxial platform

    Directory of Open Access Journals (Sweden)

    Lindner Tymoteusz

    2016-12-01

    Full Text Available The article describes investigation of rolling ball stabilization problem on a biaxial platform. The aim of the control system proposed here is to stabilize ball moving on a plane in equilibrium point. The authors proposed a control algorithm based on cascade PID and they compared it with another control method. The article shows the results of the accuracy of ball stabilization and influence of applied filter on the signal waveform. The application used to detect the ball position measured by digital camera has been written using a cross platform .Net wrapper to the OpenCV image processing library - EmguCV. The authors used the bipolar stepper motor with dedicated electronic controller. The data between the computer and the designed controller are sent with use of the RS232 standard. The control stand is based on ATmega series microcontroller.

  15. DATABASE REPLICATION IN HETEROGENOUS PLATFORM

    Directory of Open Access Journals (Sweden)

    Hendro Nindito

    2014-01-01

    Full Text Available The application of diverse database technologies in enterprises today is increasingly a common practice. To provide high availability and survavibality of real-time information, a database replication technology that has capability to replicate databases under heterogenous platforms is required. The purpose of this research is to find the technology with such capability. In this research, the data source is stored in MSSQL database server running on Windows. The data will be replicated to MySQL running on Linux as the destination. The method applied in this research is prototyping in which the processes of development and testing can be done interactively and repeatedly. The key result of this research is that the replication technology applied, which is called Oracle GoldenGate, can successfully manage to do its task in replicating data in real-time and heterogeneous platforms.

  16. YARP: Yet Another Robot Platform

    Directory of Open Access Journals (Sweden)

    Lorenzo Natale

    2008-11-01

    Full Text Available We describe YARP, Yet Another Robot Platform, an open-source project that encapsulates lessons from our experience in building humanoid robots. The goal of YARP is to minimize the effort devoted to infrastructure-level software development by facilitating code reuse, modularity and so maximize research-level development and collaboration. Humanoid robotics is a "bleeding edge" field of research, with constant flux in sensors, actuators, and processors. Code reuse and maintenance is therefore a significant challenge. We describe the main problems we faced and the solutions we adopted. In short, the main features of YARP include support for inter-process communication, image processing as well as a class hierarchy to ease code reuse across different hardware platforms. YARP is currently used and tested on Windows, Linux and QNX6 which are common operating systems used in robotics.

  17. Multithreading platform for multimedia applications

    Science.gov (United States)

    Koster, Rainer; Kramp, Thorsten

    2000-12-01

    Complex multimedia applications have diverse resource and timing requirements. A platform for building such programs therefore should supply the developer with mechanisms for managing concurrency, communication, and real-time constraints but should remain flexible with regard to scheduling policies and interaction models. We have developed such a platform consisting of a user-level threads package and operating system extensions. The threads package offers a message-based threading model uniformly integrating synchronous and asynchronous communication, inter-thread synchronization, and signal handling as well as real-time functionality and application-specific scheduling. To support this user-space flexibility an upcall mechanism links the user-level scheduler to the kernel.

  18. Stabilisation problem in biaxial platform

    Science.gov (United States)

    Lindner, Tymoteusz; Rybarczyk, Dominik; Wyrwał, Daniel

    2016-12-01

    The article describes investigation of rolling ball stabilization problem on a biaxial platform. The aim of the control system proposed here is to stabilize ball moving on a plane in equilibrium point. The authors proposed a control algorithm based on cascade PID and they compared it with another control method. The article shows the results of the accuracy of ball stabilization and influence of applied filter on the signal waveform. The application used to detect the ball position measured by digital camera has been written using a cross platform .Net wrapper to the OpenCV image processing library - EmguCV. The authors used the bipolar stepper motor with dedicated electronic controller. The data between the computer and the designed controller are sent with use of the RS232 standard. The control stand is based on ATmega series microcontroller.

  19. Climate News Across Media Platforms

    DEFF Research Database (Denmark)

    Eskjær, Mikkel Fugl

    2015-01-01

    In a changing media landscape marked by technological, institutional and cultural convergence, comparative and cross-media content analysis represents a valuable analytical tool in mapping the diverse channels of climate change communication. This paper presents a comparative study of climate...... change news on five different media platforms: newspapers, television, radio, web-news and mobile news. It investigates the themes and actors represented in public climate change communication as well as the diverse possibilities of participating in public debates and information sharing. By combining...... quantitative and qualitative content analysis the paper documents and explores the extent and character of climate change news across different media platforms. The study aims at contributing to the on-going assessment of how news media are addressing climate change at a time when old and new media...

  20. Experimental Study on Leakage Flow in Labyrinth Seals with Asymmetric Geometries

    Science.gov (United States)

    Nishii, Kazufumi; Furukawa, Akinori; Watanabe, Satoshi; Miyake, Kunihiro

    2010-06-01

    The labyrinth seal is one of non-contact seals, which is used as a seal device of rotary machines from reasons of the lubrication free and small losses. So far, many researchers have investigated the characteristics and suitable geometries of labyrinth seals, though only one directional flow of the seal has been focused up to now. As flow direction in the seal becomes changeable depending on the gas-purge system and the inner pressure variation of machines for recent applications, a guideline of designing labyrinth seal with changeable flow directions is required. In the present report, effects of seal characteristics and internal flow behaviors on various shapes of asymmetric convexity in labyrinth seals are experimentally investigated and relations between pressure loss and convexity geometries are discussed for designing a suitable seal.

  1. Thiolene and SIFEL-based Microfluidic Platforms for Liquid-Liquid Extraction.

    Science.gov (United States)

    Goyal, Sachit; Desai, Amit V; Lewis, Robert W; Ranganathan, David R; Li, Hairong; Zeng, Dexing; Reichert, David E; Kenis, Paul J A

    2014-01-01

    Microfluidic platforms provide several advantages for liquid-liquid extraction (LLE) processes over conventional methods, for example with respect to lower consumption of solvents and enhanced extraction efficiencies due to the inherent shorter diffusional distances. Here, we report the development of polymer-based parallel-flow microfluidic platforms for LLE. To date, parallel-flow microfluidic platforms have predominantly been made out of silicon or glass due to their compatibility with most organic solvents used for LLE. Fabrication of silicon and glass-based LLE platforms typically requires extensive use of photolithography, plasma or laser-based etching, high temperature (anodic) bonding, and/or wet etching with KOH or HF solutions. In contrast, polymeric microfluidic platforms can be fabricated using less involved processes, typically photolithography in combination with replica molding, hot embossing, and/or bonding at much lower temperatures. Here we report the fabrication and testing of microfluidic LLE platforms comprised of thiolene or a perfluoropolyether-based material, SIFEL, where the choice of materials was mainly guided by the need for solvent compatibility and fabrication amenability. Suitable designs for polymer-based LLE platforms that maximize extraction efficiencies within the constraints of the fabrication methods and feasible operational conditions were obtained using analytical modeling. To optimize the performance of the polymer-based LLE platforms, we systematically studied the effect of surface functionalization and of microstructures on the stability of the liquid-liquid interface and on the ability to separate the phases. As demonstrative examples, we report (i) a thiolene-based platform to determine the lipophilicity of caffeine, and (ii) a SIFEL-based platform to extract radioactive copper from an acidic aqueous solution.

  2. An Autonomous Platform Simulator (APS)

    Science.gov (United States)

    1989-06-01

    4 Da~c o! Rcp .’rt’ yeur. :nr.e,1 Page Count Master’s Thesi rmT Ju’ne 1 9 9 Ze 16 Supplementary Notat~on 14 The views expressed in this thesis are...the flight volume is based on the firing platform’s current LOS not the LOS at the time of firing. The near and far clipping planes are set to the

  3. Modular Platforms for Optofluidic Systems

    Science.gov (United States)

    Brammer, Marko; Mappes, Timo

    2014-01-01

    Optofluidics is increasingly gaining impact in a number of different fields of research, namely biology and medicine, environmental monitoring and green energy. However, the market for optofluidic products is still in the early development phase. In this manuscript, we discuss modular platforms as a potential concept to facilitate the transfer of optofluidic sensing systems to an industrial implementation. We present microfluidic and optical networks as a basis for the interconnection of optofluidic sensor modules. Finally, we show the potential for entire optofluidic networks

  4. Platform development: implications for portfolio management

    DEFF Research Database (Denmark)

    Hsuan, Juliana; Hansen, Poul H. Kyvsgård

    2007-01-01

    complex, possibly increasing the strategic risks for the firm. This paper reports preliminary findings on platform management process at LEGO, a Danish toy company. Specifically, we report the process of applying games combined with simulations and workshops in the platform development. We also propose...... a framework, based on the portfolio management thinking to evaluate the degree of modularity embedded in a given platform and to which extent it is aligned with other platforms."...

  5. Electrorheological fluid-actuated flexible platform

    Science.gov (United States)

    Liu, Liyu; Niu, Xize; Wen, Weijia; Sheng, Ping

    2006-04-01

    The design, fabrication, and performance of an electrorheological (ER) fluid-actuated flexible platform integrated on a microfluidic chip are reported in this letter. The digitally regulated ER microvalves control the four diaphragms on which a platform is sustained. With electrical input signals, the platform can perform vibrations at tunable frequencies as well as generate complex leveling modes. The flexible platform can potentially act as a microdamper when its inputs are generated from a sensor, in combination with a feedback control system.

  6. Microfluidic lab-on-a-chip platforms: requirements, characteristics and applications.

    Science.gov (United States)

    Mark, Daniel; Haeberle, Stefan; Roth, Günter; von Stetten, Felix; Zengerle, Roland

    2010-03-01

    This critical review summarizes developments in microfluidic platforms that enable the miniaturization, integration, automation and parallelization of (bio-)chemical assays (see S. Haeberle and R. Zengerle, Lab Chip, 2007, 7, 1094-1110, for an earlier review). In contrast to isolated application-specific solutions, a microfluidic platform provides a set of fluidic unit operations, which are designed for easy combination within a well-defined fabrication technology. This allows the easy, fast, and cost-efficient implementation of different application-specific (bio-)chemical processes. In our review we focus on recent developments from the last decade (2000s). We start with a brief introduction into technical advances, major market segments and promising applications. We continue with a detailed characterization of different microfluidic platforms, comprising a short definition, the functional principle, microfluidic unit operations, application examples as well as strengths and limitations of every platform. The microfluidic platforms in focus are lateral flow tests, linear actuated devices, pressure driven laminar flow, microfluidic large scale integration, segmented flow microfluidics, centrifugal microfluidics, electrokinetics, electrowetting, surface acoustic waves, and dedicated systems for massively parallel analysis. This review concludes with the attempt to provide a selection scheme for microfluidic platforms which is based on their characteristics according to key requirements of different applications and market segments. Applied selection criteria comprise portability, costs of instrument and disposability, sample throughput, number of parameters per sample, reagent consumption, precision, diversity of microfluidic unit operations and the flexibility in programming different liquid handling protocols (295 references).

  7. Towards a Framework of Digital Platform Competition

    DEFF Research Database (Denmark)

    Kazan, Erol; Tan, Chee-Wee; Lim, Eric T. K.

    2016-01-01

    This paper advances a framework for examining the competitive principles of mobile payment platforms. We postulate that the strategic interplay of platform layers will drive the competitive dynamics of platform-driven ubiquitous systems. This framework has been employed in a comparative case study...

  8. A Typology of Multi-sided Platforms

    DEFF Research Database (Denmark)

    Staykova, Kalina Stefanova; Damsgaard, Jan

    2015-01-01

    which evolved several steps into being multi-sided (Facebook). Our analysis shows a structural difference between one-sided, two-sided and multi-sided platforms and that platforms consist of a core and potentially also a periphery. The sides of a platform and the ties which connect them can be arranged...

  9. 《黄帝内经》五味补泻理论及五味补泻图构思%Design and Application of 5-flavor Tonifying-purging Figure in "Yellow Emperor's Internal Classics"

    Institute of Scientific and Technical Information of China (English)

    张大魁

    2013-01-01

      《黄帝内经》五味补泻理论是中医重要的基础理论之一,但其内容较为分散,缺乏条理和系统性,给学习和研究带来诸多不便。作者受《辅行诀五脏用药法要》“五味补泻体用图”启发,从医易同源论出发,以河图为基本框架,以《黄帝内经》五味补泻理论为理论依据,对比《黄帝内经》与《辅行诀》中五味补泻理论的不同,设计出《黄帝内经》“五味补泻图”。“五味补泻图”完整地表达了《内经》有关五方、五气、五行、五味、五脏的相互关系及五味补泻法则,具有简洁、直观、明了的特点,有助于学习和记忆,为学习、研究《内经》五味补泻理论提供了便捷。%The 5-flavor tonifying-purging theory in "Internal Classics" is one of key basic theories of TCM, but its content is disperse, lacking orderliness and systematicness, bringing inconvenience to study and research. Inspired by the 5-flavor tonifying-purging figure in "Five-organ Pharmacy Methods Edition", starting from the theory of same origin for medicine and Yi, framed basical y with river figure, based on the 5-flavor tonifying-purging theory in"Internal Classics", compare the difference between the"Internal Classics"and the"Edition", design the corelation among the 5-direction, 5-Qi, 5-ele-ment and 5-flavor, as wel as the 5-flavor tonifying-purging rule, offering convenience for studying and researching 5-flavor tonifying-purging theory in"Internal Classics".

  10. Towards a Framework of Digital Platform Disruption

    DEFF Research Database (Denmark)

    Kazan, Erol; Tan, Chee-Wee; Lim, Eric T. K.

    2014-01-01

    Digital platforms are disruptive information technology (IT) artifacts that erode conventional business logic associated with traditional market structures. This paper presents a framework for examining the disruptive potential of digital platforms whereby we postulate that the strategic interplay...... of governance regimes and platform layers is deterministic of whether disruptive derivatives are permitted to flourish. This framework has been employed in a comparative case study between centralized (i.e., PayPal) and decentralized (i.e., Coinkite) digital payment platforms to illustrate its applicability...... and yield propositions on the nature and impact of digital platform disruptions. Preliminary findings indicate that centralized digital platforms attempt to create unique configurals to obtain monopolistic power by tightly coupling platform layers, which are difficult to replicate. Conversely, decentralized...

  11. Demand forecasting and information platform in tourism

    Science.gov (United States)

    Li, Yue; Jiang, Qi-Jie

    2017-05-01

    Information asymmetry and the bullwhip effect have been serious problems in the tourism supply chain. Based on platform theory, this paper established a mathematical model to explore the inner mechanism of a platform's influence on stakeholders' ability to forecast demand in tourism. Results showed that the variance of stakeholders' demand predictions with a platform was smaller than the variance without a platform, which meant that a platform would improve predictions of demand for stakeholders. The higher information-processing ability of the platform also had other effects on demand forecasting. Research on the inner logic of the platform's influence on stakeholders has important theoretical and realistic value. This area is worthy of further study.

  12. Platform economy in Denmark – precarious employment?

    DEFF Research Database (Denmark)

    Rasmussen, Stine; Madsen, Per Kongshøj

    This paper takes a labour market perspective on the emerging concept of the 'sharing economy' or 'platform economy', which we use as a more appropriate term for the phenomenon. Platform economy is in the article understood as those business models that have emerged since the millennium, where...... digital platforms serve as the link between persons wanting to make use of certain activities, services etc. and those owning them and we only have an interest in the work-related platforms. That means platforms, where paid work is offered and demanded. International examples of this new phenomenon...... of this paper is to examine the work-related activities in the Danish platform economy and discuss whether and to what extent these activities are to be considered precarious forms of employment. The paper begins with a discussion of the terms sharing economy and platform economy in order to reach...

  13. The Implementation of an Enterprise Application Integration Platform

    Institute of Scientific and Technical Information of China (English)

    XUJungang; WANGHongan; DAIGuozhong

    2004-01-01

    With the driving of rapid reaction to the changes of business rules, enterprises realize that they need to transfer their applications from single function to management of the whole processing flow. This transfer requires the enterprises to integrate the existing individual systems and re-configure its business systems. To meet this challenge, we have designed and implemented an Application integration platform for process industry (AIP/PI),which is model-driven and component-based, and composed of six main components: application configuration and execution platform, data accessing middleware, data collecting middleware, enterprise core database for production management, enterprise real-time database for production process, data integration and material balancing system. Our work has been applied to one refinery plant.

  14. A portable chemotaxis platform for short and long term analysis.

    Directory of Open Access Journals (Sweden)

    Chenjie Xu

    Full Text Available Flow-based microfluidic systems have been widely utilized for cell migration studies given their ability to generate versatile and precisely defined chemical gradients and to permit direct visualization of migrating cells. Nonetheless, the general need for bulky peripherals such as mechanical pumps and tubing and the complicated setup procedures significantly limit the widespread use of these microfluidic systems for cell migration studies. Here we present a simple method to power microfluidic devices for chemotaxis assays using the commercially available ALZET® osmotic pumps. Specifically, we developed a standalone chemotaxis platform that has the same footprint as a multiwell plate and can generate well-defined, stable chemical gradients continuously for up to 7 days. Using this platform, we validated the short-term (24 hours and long-term (72 hours concentration dependent PDGF-BB chemotaxis response of human bone marrow derived mesenchymal stem cells.

  15. Advanced Programming Platform for efficient use of Data Parallel Hardware

    CERN Document Server

    Cabellos, Luis

    2012-01-01

    Graphics processing units (GPU) had evolved from a specialized hardware capable to render high quality graphics in games to a commodity hardware for effective processing blocks of data in a parallel schema. This evolution is particularly interesting for scientific groups, which traditionally use mainly CPU as a work horse, and now can profit of the arrival of GPU hardware to HPC clusters. This new GPU hardware promises a boost in peak performance, but it is not trivial to use. In this article a programming platform designed to promote a direct use of this specialized hardware is presented. This platform includes a visual editor of parallel data flows and it is oriented to the execution in distributed clusters with GPUs. Examples of application in two characteristic problems, Fast Fourier Transform and Image Compression, are also shown.

  16. Flow Boiling and Condensation Experiment (FBCE) for the International Space Station

    Science.gov (United States)

    Mudawar, Issam; Hasan, Mohammad M.; Kharangate, Chirag; O'Neill, Lucas; Konishi, Chris; Nahra, Henry; Hall, Nancy; Balasubramaniam, R.; Mackey, Jeffrey

    2015-01-01

    The proposed research aims to develop an integrated two-phase flow boiling/condensation facility for the International Space Station (ISS) to serve as primary platform for obtaining two-phase flow and heat transfer data in microgravity.

  17. Numerical analysis of seawater circulation in carbonate platforms: II. The dynamic interaction between geothermal and brine reflux circulation

    Science.gov (United States)

    Jones, G.D.; Whitaker, F.F.; Smart, P.L.; Sanford, W.E.

    2004-01-01

    Density-driven seawater circulation may occur in carbonate platforms due to geothermal heating and / or reflux of water of elevated salinity. In geothermal circulation lateral contrasts in temperature between seawater and platform groundwaters warmed by the geothermal heat flux result in upward convective flow, with colder seawater drawn into the platform at depth. With reflux circulation, platform-top waters concentrated by evaporation flow downward, displacing less dense underlying groundwaters. We have used a variable density groundwater flow model to examine the pattern, magnitude and interaction of these two different circulation mechanisms, for mesosaline platform-top waters (50???) and brines concentrated up to saturation with respect to gypsum (150???) and halite (246???). Geothermal circulation, most active around the platform margin, becomes restricted and eventually shut-off by reflux of brines from the platform interior towards the margin. The persistence of geothermal circulation is dependent on the rate of brine reflux, which is proportional to the concentration of platform-top brines and also critically dependent on the magnitude and distribution of permeability. Low permeability evaporites can severely restrict reflux whereas high permeability units in hydraulic continuity enhance brine transport. Reduction in permeability with depth and anisotropy of permeability (kv < < kh) focuses flow laterally in the shallow subsurface (<1 km), resulting in a horizontally elongated brine plume. Aquifer porosity and dispersivity are relatively minor controls on reflux. Platform brines can entrain surficial seawater when brine generating conditions cease but the platform-top remains submerged, a variant of reflux we term "latent reflux". Brines concentrated up to gypsum saturation have relatively long residence times of at least 100 times the duration of the reflux event. They thus represent a long-term control on post-reflux groundwater circulation, and

  18. Education Platform at ZDM8.

    Science.gov (United States)

    Lyman Gingerich, Jamie S; Pickart, Michael A; Pierret, Chris

    2016-04-01

    Interest among the zebrafish community in education and science accessibility for all ages has increased. At the 8th Annual Zebrafish Disease Models Conference (ZDM8), a specifically designed session enabled professional scientists, educators, and students to have a venue to present their science, discuss ideas in education, and partner to navigate a scientific meeting as an educational experience. This meeting report describes the format of the Platform Session as well as challenges and future plans to leverage impact of conferences on the local communities.

  19. Generational Transitions in Platform Markets

    DEFF Research Database (Denmark)

    Kretschmer, Tobias; Claussen, Jörg

    2016-01-01

    The introduction of a new product generation forces incumbents in platform markets to rebuild their installed base of complementary products. Using three different data sets on the U.S. market for video game consoles, we show that incumbents can, to some extent, substitute for rebuilding their new...... installed base by making their new products backward compatible, which lets them draw on the installed base of software for the parent generation. However, while this positive direct effect of backward compatibility dominates in our setting, we also observe a (weaker) negative indirect effect working...

  20. Technical Note: A fully automated purge and trap GC-MS system for quantification of volatile organic compound (VOC fluxes between the ocean and atmosphere

    Directory of Open Access Journals (Sweden)

    S. J. Andrews

    2015-04-01

    Full Text Available The oceans are a key source of a number of atmospherically important volatile gases. The accurate and robust determination of trace gases in seawater is a significant analytical challenge, requiring reproducible and ideally automated sample handling, a high efficiency of seawater–air transfer, removal of water vapour from the sample stream, and high sensitivity and selectivity of the analysis. Here we describe a system that was developed for the fully automated analysis of dissolved very short-lived halogenated species (VSLS sampled from an under-way seawater supply. The system can also be used for semi-automated batch sampling from Niskin bottles filled during CTD (conductivity, temperature, depth profiles. The essential components comprise a bespoke, automated purge and trap (AutoP & T unit coupled to a commercial thermal desorption and gas chromatograph mass spectrometer (TD-GC-MS. The AutoP & T system has completed five research cruises, from the tropics to the poles, and collected over 2500 oceanic samples to date. It is able to quantify >25 species over a boiling point range of 34–180 °C with Henry's law coefficients of 0.018 and greater (CH22l, kHcc dimensionless gas/aqueous and has been used to measure organic sulfurs, hydrocarbons, halocarbons and terpenes. In the eastern tropical Pacific, the high sensitivity and sampling frequency provided new information regarding the distribution of VSLS, including novel measurements of a photolytically driven diurnal cycle of CH22l within the surface ocean water.