WorldWideScience

Sample records for plate circuit reconstructions

  1. Tomographic reconstruction of an integrated circuit interconnect

    Energy Technology Data Exchange (ETDEWEB)

    Levine, Z.H. [National Institute of Standards and Technology, Gaithersburg, Maryland 20899 (United States); Kalukin, A.R. [Physics Department, Rensselaer Polytechnic Institute, Troy, New York 12180-3590 (United States); Frigo, S.P.; McNulty, I. [Advanced Photon Source, Argonne National Laboratory, Argonne, Illinois 60439 (United States); Kuhn, M. [Digital Equipment Corporation, Hudson, Massachusetts 01749 (United States)

    1999-01-01

    An Al{endash}W-silica integrated circuit interconnect sample was thinned to several {mu}m and scanned across a 200 nm focal spot of a Fresnel zone plate operating at photon energy of 1573 eV. The experiment was performed on beamline 2-ID-B of the Advanced Photon Source, a third-generation synchrotron facility. Thirteen scanned projections of the sample were acquired over the angular range {plus_minus}69.2{degree}. At least 301{times}301 pixels were acquired at each angle with a step size of 77{times}57 nm. A three-dimensional image with an approximate uncertainty of 400 nm was reconstructed from projection data using a standard algorithm. The two layers of the integrated circuit and the presence of the focused ion beam markers on the surface of the sample are clearly shown in the reconstruction. {copyright} {ital 1999 American Institute of Physics.}

  2. Plate tectonic raster reconstruction in GPlates

    OpenAIRE

    2014-01-01

    We describe a novel method implemented in the GPlates plate tectonic reconstruction software to interactively reconstruct arbitrarily high-resolution raster data to past geological times using a rotation model. The approach is based on the projection of geo-referenced raster data into a cube map followed by a reverse projection onto rotated tectonic plates on the surface of the globe. This decouples the rendering of a geo-referenced raster from its reconstruction, providing ...

  3. Plate tectonic raster reconstruction in GPlates

    Directory of Open Access Journals (Sweden)

    J. Cannon

    2014-03-01

    Full Text Available We describe a novel method implemented in the GPlates plate tectonic reconstruction software to interactively reconstruct arbitrarily high-resolution raster data to past geological times using a rotation model. The approach is based on the projection of geo-referenced raster data into a cube map followed by a reverse projection onto rotated tectonic plates on the surface of the globe. This decouples the rendering of a geo-referenced raster from its reconstruction, providing a number of benefits including a simple implementation and the ability to combine rasters with different geo-referencing or inbuilt raster projections. The cube map projection is accelerated by graphics hardware in a wide variety of computer systems manufactured over the last decade. Furthermore, by integrating a multi-resolution tile partitioning into the cube map we can provide on-demand tile streaming, level-of-detail rendering and hierarchical visibility culling enabling researchers to visually explore essentially unlimited resolution geophysical raster data attached to tectonic plates and reconstructed through geological time. This capability forms the basis for interactively building and improving plate reconstructions in an iterative fashion, particularly for tectonically complex regions.

  4. A Novel Technique to Perform Plating on Printed Circuit Board

    Directory of Open Access Journals (Sweden)

    S. Jayapoorani

    2011-01-01

    Full Text Available Problem statement: This research attempts to optimize the parameters for pulse plating of silver on printed circuit board. The idea here is to use pulse plating technique which is metal deposition by pulsed electrolysis method. Approach: Printed Circuit Boards (PCB plays a major role in all communication and electronics industry. Silver is a ductile and malleable metal which has 7% higher conductivity than copper. Here the electro deposit is influenced by current density, silver concentration in the bath, applied current type. Pulse plating technique is used in double sided printed circuit board especially in the case of plated through hole technique. Here exist a necessity to do plating which will deposit a metal wall in the substrate and it will connect between the components. Results: This method of pulse plating proves that it avoids the disadvantage of rough deposition that is caused due to DC plating in PCB's. Conclusion: The surface morphology and the grain size is measured using XRD analysis and it proves that the number of pin holes is reduced.

  5. Reconstruction of virtual neural circuits in an insect brain

    Directory of Open Access Journals (Sweden)

    Shigehiro Namiki

    2009-09-01

    Full Text Available The reconstruction of large-scale nervous systems represents a major scientific and engineering challenge in current neuroscience research that needs to be resolved in order to understand the emergent properties of such systems. We focus on insect nervous systems because they represent a good compromise between architectural simplicity and the ability to generate a rich behavioral repertoire. In insects, several sensory maps have been reconstructed so far. We provide an overview over this work including our reconstruction of population activity in the primary olfactory network, the antennal lobe. Our reconstruction approach, that also provides functional connectivity data, will be refined and extended to allow the building of larger scale neural circuits up to entire insect brains, from sensory input to motor output.

  6. Discrete algebraic reconstruction technique: a new approach for superresolution reconstruction of license plates

    Science.gov (United States)

    Zarei Zefreh, Karim; van Aarle, Wim; Batenburg, K. Joost; Sijbers, Jan

    2013-10-01

    A new superresolution algorithm is proposed to reconstruct a high-resolution license plate image from a set of low-resolution camera images. The reconstruction methodology is based on the discrete algebraic reconstruction technique (DART), a recently developed reconstruction method. While DART has already been successfully applied in tomographic imaging, it has not yet been transferred to the field of camera imaging. DART is introduced for camera imaging through a demonstration of how prior knowledge of the colors of the license plate can be directly exploited during the reconstruction of a high-resolution image from a set of low-resolution images. Simulation experiments show that DART can reconstruct images with superior quality compared to conventional reconstruction methods.

  7. High-resolution reconstructions of Pacific-North America plate motion: 20 Ma to present

    Science.gov (United States)

    DeMets, C.; Merkouriev, S.

    2016-11-01

    We present new rotations that describe the relative positions and velocities of the Pacific and North America plates at 22 times during the past 19.7 Myr, offering ≈1-Myr temporal resolution for studies of the geotectonic evolution of western North America and other plate boundary locations. Derived from ≈18 000 magnetic reversal, fracture zone and transform fault identifications from the Pacific-Antarctic-Nubia-North America plate circuit and the velocities of 935 GPS sites on the Pacific and North America plates, the new rotations and GPS-derived angular velocity indicate that the rate of motion between the two plates increased by ≈70 per cent from 19.7 to 9±1 Ma, but changed by less than 2 per cent since 8 Ma and even less since 4.2 Ma. The rotations further suggest that the relative plate direction has rotated clockwise for most of the past 20 Myr, with a possible hiatus from 9 to 5 Ma. This conflicts with previously reported evidence for a significant clockwise change in the plate direction at ≈8-6 Ma. Our new rotations indicate that Pacific plate motion became obliquely convergent with respect to the San Andreas Fault of central California at 5.2-4.2 Ma, in agreement with geological evidence for a Pliocene onset of folding and faulting in central California. Our reconstruction of the northern Gulf of California at 6.3 Ma differs by only 15-30 km from structurally derived reconstructions after including 3-4 km Myr-1 of geodetically measured slip between the Baja California Peninsula and Pacific plate. This implies an approximate 15-30 km upper bound for plate non-rigidity integrated around the global circuit at 6.3 Ma. A much larger 200±54 km discrepancy between our reconstruction of the northern Gulf of California at 12 Ma and that estimated from structural and marine geophysical observations suggests that faults in northwestern Mexico or possibly west of the Baja California Peninsula accommodated large amounts of obliquely divergent dextral shear

  8. Reconstruction plate fixation of subtrochanteric femoral fractures in children.

    Science.gov (United States)

    El-Sayed, Moustafa; Abulsaad, Mazen; El-Hadidi, Mahmoud; El-Adl, Wael; El-Batouty, Magdy

    2007-08-01

    Pediatric subtrochanteric femoral fractures are rare and have received limited attention in the literature Treatment is controversial. Different treatment options are used: skin traction, 90/90 skeletal traction, spica casting, cast bracing, internal fixation and external fixation. The aim of this study is to present our results with internal fixation of subtrochanteric femoral fractures in children using a reconstruction plate. Between 2000 and 2004, eighteen patients with closed subtrochanteric femoral fractures were treated in the Mansoura Emergency Hospital. The average age at the time of injury was 8.2 years (range 5.3 years to 11.5 years). Pathological fractures and fractures associated with neuromuscular diseases were excluded from this study. Eight patients had head injuries and/or multiple injuries. In all cases a single 4.5 mm contoured reconstruction plate was used and a 6.5 mm cancellous screw was inserted through the plate into the femoral neck. Average follow-up was 38 months (range, 12 to 47 months). All fractures united with anatomical alignment within an average of 8 weeks (range 6 to 12 weeks). There were no deep infections and no significant limb length discrepancies. At the latest follow-up, no patient had any restriction of activities. Internal fixation with a reconstruction plate appears as a good treatment option for children with subtrochanteric femoral fractures.

  9. Anterior cruciate ligament reconstruction in children with open growth plates

    Directory of Open Access Journals (Sweden)

    Rustam Sh Sadykov

    2016-09-01

    Full Text Available Introduction. Anterior cruciate ligament (ACL tears are observed in 10%–32% of all traumatic lesions of the knee joint in children. Open growth plates are a serious problem in the treatment of ACL tears. Most modern methods of ACL reconstruction use transepiphyseal channels, which go through the growth plates. This may lead to angle deformity of the knee development, limb shortening and early arthritis. Material and methods. We observed 12 patients (11–17 years old; mean age, 13.2 years with ACL tears with opened growth plates, who were operated on between 2006 and 2010. ACL reconstruction was performed arthroscopically using the BTB-technique and synthetic grafts DONA-M. Results. In all cases, we achieved poor results, especially when the operation was done by BTB. We avoided shortening of the leg, but arthritis was common and progressed quickly. When we tried stabilize the joint, we achieved the reverse effect – pain in the knee, with a decreased quality of life. Conclusion. Our results demonstrate that ACL reconstruction in children with opened growth pates is not effective; we suggest performing the procedure after the growth has finished.

  10. Stabilization of mobile mandibular segments in mandibular reconstruction: use of spanning reconstruction plate.

    Science.gov (United States)

    Yap, Yan Lin; Lim, Jane; Ong, Wei Chen; Yeo, Matthew; Lee, Hanjing; Lim, Thiam Chye

    2012-09-01

    The fibular free flap is the gold standard for mandibular reconstruction. Accurate 3-dimensional contouring and precise alignment of the fibula is critical for reestablishing native occlusion and facial symmetry. Following segmental mandibulectomy, the remaining mandibular fragments become freely mobile. Various stabilization methods including external fixation, intermaxillary fixation, and preplating with reconstruction plate have been used. We describe a modification to the preplating technique. After wide resection of buccal squamous cell carcinoma, our patient had an 11-cm mandibular defect from the angle of the left mandible to the right midparasymphyseal region. A single 2.0-mm Unilock® (Synthes, Singapore) plate was used to span the defect. This was placed on the vestibular aspect of the superior border of the mandibular remnants before resection. Segmental mandibulectomy was then performed with the plate removed. The spanning plate was then reattached to provide rigid fixation. The fibular bone was contoured with a single osteotomy and reattached. The conventional technique involves molding of the plate at the inferior border of the mandible. This is time-consuming and not possible in patients with distorted mandibular contour. It is also difficult to fit the osteotomized fibula to the contoured plate. In comparison, the superiorly positioned spanning plate achieve rigid fixation of the mandible while leaving the defect completely free and unhampered by hardware, allowing space for planning osteotomies and easier fixation of the neomandible. Using this modified technique, we are able to recreate the original mandibular profile with ease.

  11. CAD-CAM plates versus conventional fixation plates for primary mandibular reconstruction: A biomechanical in vitro analysis.

    Science.gov (United States)

    Rendenbach, Carsten; Sellenschloh, Kay; Gerbig, Lucca; Morlock, Michael M; Beck-Broichsitter, Benedicta; Smeets, Ralf; Heiland, Max; Huber, Gerd; Hanken, Henning

    2017-09-01

    CAD/CAM reconstruction plates have become a viable option for mandible reconstruction. The aim of this study was to determine whether CAD/CAM plates provide higher fatigue strength compared with conventional fixation systems. 1.0 mm miniplates, 2.0 mm conventional locking plates (DePuy Synthes, Umkirch, Germany), and 2.0 mm CAD/CAM plates (Materialise, Leuven, Belgium/DePuy Synthes) were used to reconstruct a polyurethane mandible model (Synbone, Malans, CH) with cortical and cancellous bone equivalents. Mastication was simulated via cyclic dynamic testing using a universal testing machine (MTS, Bionix, Eden Prairie, MN, USA) until material failure reached a rate of 1 Hz with increasing loads on the left side. No significant difference was found between the groups until a load of 300 N. At higher loads, vertical displacement differed increasingly, with a poorer performance of miniplates (p = 0.04). Plate breakage occurred in miniplates and conventional locking plates. Screw breakage was recorded as the primary failure mechanism in CAD/CAM plates. Stiffness was significantly higher with the CAD/CAM plates (p = 0.04). CAD/CAM plates and reconstruction plates provide higher fatigue strength than miniplates, and stiffness is highest in CAD/CAM systems. All tested fixation methods seem sufficiently stable for mandible reconstruction. Copyright © 2017 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved.

  12. Management of exposure of three-dimensional mandibular reconstructive plates in mandibular reconstruction:Report of 2 cases

    Institute of Scientific and Technical Information of China (English)

    XU Li-qun1; WU Andri; ZHANG Chen-ping; ZHENG Jia-wei

    2004-01-01

    Exposure of three-dimensional mandibular reconstructive plate was a main complication in its clinical application, which includes intraoral exposure and extraoral exposure. This paper reported two typical cases with plate exposure and reviewed the literatures in analysis of the causes of plate exposure and its preventive measures.

  13. Late sciatic nerve axonotmesis following acetabular reconstruction plate.

    Science.gov (United States)

    Moreta, J; Foruria, X; Labayru, F

    2016-01-01

    Sciatic nerve injuries associated with acetabular fractures can be post-traumatic, perioperative or postoperative. Late postoperative injury is very uncommon and can be due to heterotopic ossifications, muscular scarring, or implant migration. A case is presented of a patient with a previous transverse acetabular fracture treated with a reconstruction plate for the posterior column. After 17 years, she presented with progressive pain and motor deficit in the sciatic territory. Radiological and neurophysiological assessments were performed and the patient underwent surgical decompression of the sciatic nerve. A transection of the nerve was observed that was due to extended compression of one of the screws. At 4 years postoperatively, her pain had substantially diminished and the paresthesias in her leg had resolved. However, her motor symptoms did not improve. This case report could be relevant due to this uncommon delayed sciatic nerve injury due to prolonged hardware impingement. Copyright © 2014 SECOT. Published by Elsevier Espana. All rights reserved.

  14. Copper circuit patterning on polymer using selective surface modification and electroless plating

    Science.gov (United States)

    Park, Sang Jin; Ko, Tae-Jun; Yoon, Juil; Moon, Myoung-Woon; Oh, Kyu Hwan; Han, Jun Hyun

    2017-02-01

    We have examined a potential new and simple method for patterning a copper circuit on PET substrate by copper electroless plating, without the pretreatment steps (i.e., sensitization and activation) for electroless plating as well as the etching processes of conventional circuit patterning. A patterned mask coated with a catalyst material, Ag, for the reduction of Cu ions, is placed on a PET substrate. Subsequent oxygen plasma treatment of the PET substrate covered with the mask promotes the selective generation of anisotropic pillar- or hair-like nanostructures coated with co-deposited nanoparticles of the catalyst material on PET. After oxygen plasma treatment, a Cu circuit is well formed just by dipping the plasma-treated PET into a Cu electroless plating solution. By increasing the oxygen gas pressure in the chamber, the height of the nanostructures increases and the Ag catalyst particles are coated on not only the top but also the side surfaces of the nanostructures. Strong mechanical interlocking between the Cu circuit and PET substrate is produced by the large surface area of the nanostructures, and enhances peel strength. Results indicate this new simple two step (plasma surface modification and pretreatment-free electroless plating) method can be used to produce a flexible Cu circuit with good adhesion.

  15. Hemimandibulectomy with full angular mandibular plate reconstruction follicular Ameloblastoma patient

    Directory of Open Access Journals (Sweden)

    Susanti Bulan

    2017-08-01

    Full Text Available Introduction :Ameloblastoma is an aggressive benign of odontogenic origin tumor; cystic shape, slowly growth; no pain; local invasive; infiltrate muscle; and bone destruction. Based on histopathology ameloblastomas are classified: Follicular, acanthomatous, granular cell, basal cell, and plexiform. Follicular and plexiformameloblastomas are the most common, with incidence rates 27.7% and 21.1%. Follicular ameloblastoma is characterized by recurrence rate (29.5%; plexiformameloblastoma (16.7%; and acanthomatousameloblastoma (4.5%. Early diagnosis with prompt and adequate management decrease recurrence and get good prognosis. Objective : to evaluate recurrence of follicular ameloblastoma after surgery; to evaluate  stomatognatic function and aesthetic problems. Case report : a 55 y.o. female patient with lump at left cheek since 1 year before admission; initially was small in size; gradually increased, no history of trauma, pain, febrile, and discharge. Based on clinical, histopathological, radiological, CT scan, it was diagnosed follicular ameloblastoma. The treatment was left hemimandibulectomy with full angular mandibular plate reconstruction. Discussion :Ameloblastoma is a locally destructive tumor with recurrence if not entirely excised. The goal of treatment ameloblastoma is wide excision and reconstruction of surgical defect. Then, it is followed up to evaluate recurrence, stomatognatic function, and aesthetic problems. Conclusion : Prognosis is good if an early diagnosis of the lesion is made with prompt and adequate surgical intervention.

  16. Next-generation plate-tectonic reconstructions using GPlates

    OpenAIRE

    2011-01-01

    Plate tectonics is the kinematic theory that describes the large-scale motions and events of the outermost shell of the solid Earth in terms of the relative motions and interactions of large, rigid, interlocking fragments of lithosphere called tectonic plates. Plates form and disappear incrementally over time as a result of tectonic processes. There are currently about a dozen major plates on the surface of the Earth, and many minor ones. The present-day configuration of tectonic plates is il...

  17. Evidence for relative motions between the Indian and Australian Plates during the last 20 m.y. from plate tectonic reconstructions: Implications for the deformation of the Indo-Australian Plate

    Science.gov (United States)

    Royer, Jean-Yves; Chang, Ted

    1991-07-01

    We use plate tectonic reconstructions to establish whether motions between India and Australia occurred since chron 18 (43 Ma). We test the Africa/Antarctica/Australia/India plate circuit closure at chrons 5 (10 Ma), 6 (21 Ma) and 13 (36 Ma) using a compilation of magnetic anomalies and fracture zone traces from the Southeast, Southwest, Central Indian and the Carlsberg ridges. Additional reconstructions at chrons 23 (55 Ma) and 26 (61 Ma) are used to estimate the overall motion between India and Australia. Relative motions between the Indian and Australian plates are estimated using the plate circuit India → Africa → Australia. A new statistical approach, based on spherical regression analyses, is used to assess the uncertainty of the "best-fitting" finite rotations from the uncertainties in the data. The uncertainty in a rotation is described by a covariance matrix directly related to the geometry of the reconstructed plate boundary, to the distribution and estimated errors of the data points along it. Our parameterization of the rotations allows for simple combination of the rotation uncertainties along a plate circuit path. Results for chron 5 are remarkably consistent with present-day kinematics in the Indian Ocean, except that the Arabian and Indian plates are found to be separate plates. Comparisons of the motions between the Indian and African plates across the Carlsberg Ridge with that between the Australian and African plates across the Central Indian Ridge evidence a significant counterclockwise rotation of the Australian plate relative to the Indian plate about a pole located in the Central Indian Basin. The determinations are consistent for chrons 26, 13, 6 and 5. Determination at chron 23 is different but questionable due to the small number of available data. We propose two alternative solutions that both predict convergence within the Wharton and Central Indian basins and extension in the vicinity of the Chagos-Laccadive Ridge. The first

  18. Dynamic Error Analysis Method for Vibration Shape Reconstruction of Smart FBG Plate Structure

    Directory of Open Access Journals (Sweden)

    Hesheng Zhang

    2016-01-01

    Full Text Available Shape reconstruction of aerospace plate structure is an important issue for safe operation of aerospace vehicles. One way to achieve such reconstruction is by constructing smart fiber Bragg grating (FBG plate structure with discrete distributed FBG sensor arrays using reconstruction algorithms in which error analysis of reconstruction algorithm is a key link. Considering that traditional error analysis methods can only deal with static data, a new dynamic data error analysis method are proposed based on LMS algorithm for shape reconstruction of smart FBG plate structure. Firstly, smart FBG structure and orthogonal curved network based reconstruction method is introduced. Then, a dynamic error analysis model is proposed for dynamic reconstruction error analysis. Thirdly, the parameter identification is done for the proposed dynamic error analysis model based on least mean square (LMS algorithm. Finally, an experimental verification platform is constructed and experimental dynamic reconstruction analysis is done. Experimental results show that the dynamic characteristics of the reconstruction performance for plate structure can be obtained accurately based on the proposed dynamic error analysis method. The proposed method can also be used for other data acquisition systems and data processing systems as a general error analysis method.

  19. Pin guidance of reconstruction plate contour: an expanded role of external fixation.

    Science.gov (United States)

    Jaquet, Yves; Higgins, Kevin M; Enepekides, Danny J

    2011-09-01

    This article presents a modification of intraoperative external fixation for mandibular reconstruction with free tissue flaps. This technique is indicated when preregistration of the reconstruction plate is not possible due to transmandibular tumor extension. Once standard external fixation has been carried out and prior to segmental mandibulectomy, additional pins are fixed to the connecting rod that delineate the mandibular contour in three-dimensional (3D) space. Following mandibulectomy, these pins allow accurate contouring of the reconstruction plate and improved restoration of mandibular contour, projection, and dental occlusion. A step-by-step description of the technique using models and intraoperative photos is presented. This method of mandibular reconstruction is a simple and time-effective alternative to intraoperative computer navigation and 3D modeling in select cases of oral carcinoma where tumor infiltration of the outer mandibular cortex precludes prebending of the reconstruction plates.

  20. Comparison of miniplates and biodegradable plates in reconstruction of the mandible with a fibular free flap.

    Science.gov (United States)

    Kim, N K; Nam, W; Kim, H J

    2015-03-01

    Miniplates and reconstruction plates are usually used to fix a fibular free flap, the gold standard in reconstruction of large segmental mandibular defects. Though biodegradable plates are used in orthognathic operations and repair of fractures nowadays, we know of no studies of the use of biodegradable plates in the reconstruction of segmental mandibular defects including a fibular free flap. We retrospectively reviewed 47 patients who had reconstruction of segmental mandibular defects with fibular free flaps during the past 10 years, and recorded clinical data and morbidity. We compared patients who had reconstruction of such defects with fibular free flaps and miniplates (n=26) with those in whom biodegradable plates had been used (n=21). There was no significant difference between miniplates and biodegradable plates with regard to overall complications (p=0.45) and failure of flaps (p=0.59). After confounding factors had been adjusted for with Cox's proportional hazards regression, there was no significant difference in the proportion of patients who developed a complication between the two groups (p=0.4). The type of plate does not seem to affect overall morbidity in reconstruction of the mandible with a fibular free flap.

  1. Avoiding short circuits from zinc metal dendrites in anode by backside-plating configuration

    Science.gov (United States)

    Higashi, Shougo; Lee, Seok Woo; Lee, Jang Soo; Takechi, Kensuke; Cui, Yi

    2016-06-01

    Portable power sources and grid-scale storage both require batteries combining high energy density and low cost. Zinc metal battery systems are attractive due to the low cost of zinc and its high charge-storage capacity. However, under repeated plating and stripping, zinc metal anodes undergo a well-known problem, zinc dendrite formation, causing internal shorting. Here we show a backside-plating configuration that enables long-term cycling of zinc metal batteries without shorting. We demonstrate 800 stable cycles of nickel-zinc batteries with good power rate (20 mA cm-2, 20 C rate for our anodes). Such a backside-plating method can be applied to not only zinc metal systems but also other metal-based electrodes suffering from internal short circuits.

  2. Adult Neurogenesis Leads to the Functional Reconstruction of a Telencephalic Neural Circuit

    Science.gov (United States)

    Macedo-Lima, Matheus; Miller, Kimberly E.; Brenowitz, Eliot A.

    2016-01-01

    Seasonally breeding songbirds exhibit pronounced annual changes in song behavior, and in the morphology and physiology of the telencephalic neural circuit underlying production of learned song. Each breeding season, new adult-born neurons are added to the pallial nucleus HVC in response to seasonal changes in steroid hormone levels, and send long axonal projections to their target nucleus, the robust nucleus of the arcopallium (RA). We investigated the role that adult neurogenesis plays in the seasonal reconstruction of this circuit. We labeled newborn HVC neurons with BrdU, and RA-projecting HVC neurons (HVCRA) with retrograde tracer injected in RA of adult male white-crowned sparrows (Zonotrichia leucophrys gambelii) in breeding or nonbreeding conditions. We found that there were many more HVCRA neurons in breeding than nonbreeding birds. Furthermore, we observed that more newborn HVC neurons were back-filled by the tracer in breeding animals. Behaviorally, song structure degraded as the HVC-RA circuit degenerated, and recovered as the circuit regenerated, in close correlation with the number of new HVCRA neurons. These results support the hypothesis that the HVC-RA circuit degenerates in nonbreeding birds, and that newborn neurons reconstruct the circuit in breeding birds, leading to functional recovery of song behavior. SIGNIFICANCE STATEMENT We investigated the role that adult neurogenesis plays in the seasonal reconstruction of a telencephalic neural circuit that controls song behavior in white-crowned sparrows. We showed that nonbreeding birds had a 36%–49% reduction in the number of projection neurons compared with breeding birds, and the regeneration of the circuit in the breeding season is due to the integration of adult-born projection neurons. Additionally, song structure degraded as the circuit degenerated and recovered as the circuit regenerated, in close correlation with new projection neuron number. This study demonstrates that steroid hormones

  3. The influence of circuit inductance on the energy characteristics of electric discharge and deformation of plates in water

    Science.gov (United States)

    Kosenkov, V. M.; Bychkov, V. M.

    2017-08-01

    We have experimentally studied the influence of discharge-circuit inductance on the efficiency of conversion of energy stored in a capacitor bank, evolved in the electric-discharge channel in water, and spent for the resulting plastic deformation of plates. It is established for the first time that a growth in inductance of the discharge circuit produces a positive effect on the deformation of plates by increasing the amount of energy spent in this process.

  4. A comparative study on the customized design of mandibular reconstruction plates using finite element method

    Directory of Open Access Journals (Sweden)

    Abdulrahman Al-Ahmari

    2015-07-01

    Full Text Available Mandible defects and its deformities are serious complications and its precise reconstruction is one of the most challenging tasks in oral maxillofacial surgery. The commercially available standard mandible implants are manually bended before surgery to custom fit the patient’s jaw. A slight mismatch in the plate and bone alignment may result in the implant failure. However, with the integration of computer-aided design, rapid prototyping, and advanced imaging systems (computed tomography or magnetic resonance imaging, it is possible to produce a customized mandible implant that can precisely fit the patient’s jaw. The aim of this article is to compare a new design of customized mandible implant (sinewave plate and compare it with the commonly used straight implant design. The finite element–simulated results reveal that the commonly used straight reconstruction plates are more prone to loosening of the screws due to its higher strain concentration on the screw hole when compared to newly designed sinewave reconstruction plate. Moreover, the straight plate is more sensitive to the chewing load variations and develops almost 20% increase in the stresses when compared to sinewave plate. The study reveals that the sinewave reconstruction plate can significantly enhance the stability and safety of the mandible implant.

  5. Comparative study of W-shaped angular plate and reconstruction plate in treating posterior wall fractures of the acetabulum.

    Directory of Open Access Journals (Sweden)

    Qi Zhang

    Full Text Available OBJECTIVE: This study aims to assess the medium-term results of the reconstruction of posterior wall fractures using a W-shaped acetabular angular plate (WAAP compared to those fixed using a reconstruction plate. METHODS: Between July 2006 and March 2009, we performed a retrospective study, which collected data for any patient treated for a posterior acetabular wall fracture. At the time of treatment, patients were either treated using a WAAP or a pelvic reconstruction plate. The intraoperative fluoroscopic images for both groups were compared. The quality of reduction and radiological grading were assessed according to the criteria developed by Matta. The clinical assessment was based on a modified Merle d'Aubigne and Postel scoring. RESULTS: 53 patients met the inclusion criteria and were followed up for an average of 38 months. 25 patients were treated with a WAAP (study group, and 28 patients were treated with a pelvic reconstruction plate (control group. The intraoperative fluoroscopic images of the study group confirmed extra-articular screw placement in all cases. In the control group, intra-articular screw placement was observed intraoperatively in 5 patients (17.86%, and the definitive location of the periarticular hardware could not be determined in 4 patients (14.29% during the operation. The differences between the two groups were statistically significant (p = 0.002. In contrast, the quality of fracture reduction, clinical outcomes, and radiological grading in the study group were not significantly different from those of the control group (p>0.05. The radiographic grade was strongly associated with the clinical outcomes in both the study and control groups (p<0.05. CONCLUSION: Reconstruction of posterior wall fractures of the acetabulum using a WAAP can help avoid screw penetration of the hip joint, provide a stable fixation of the posterior wall, and ensure good clinical outcomes.

  6. 3D-FEM and histomorphology of mandibular reconstruction with the titanium functionally dynamic bridging plate.

    Science.gov (United States)

    Schuller-Götzburg, P; Pleschberger, M; Rammerstorfer, F G; Krenkel, C

    2009-12-01

    Biomechanical investigation of the mandible is difficult due to the complex geometrical structure. A three-dimensional finite element model of the mandible and masticatory muscles was produced with approximately 23,000 hexahedral elements. On this model, mesial and distal portions of the jaw were resected and bridged with a buccal and/or caudally positioned bridging plate. The plate was fixed caudal or buccal to the mandible. The defect was left as it was or reconstructed with an exactly fitting transplant defined as bone. The jaw was loaded at a predefined point. The changes in stresses and deformations of bone, the transplant and the bridging plate were analysed. In the caudally positioned bridging plate, finite element analysis showed lesser stresses around the fixation screws of the bridging plate. During reconstruction of the lateral defect, the buccal (ramus)-caudal (corpus) position of the bridging plate showed fewer stresses and deformations than purely buccal positioning. The caudal position of the bridging plate has biomechanical advantages and facilitates fixation of the plate, and fixation of a bone graft on the jaw stumps. Histomorphological investigations, 12 weeks and 7 years after reconstruction, show partial osseous integration or transformation of autologous iliac crest transplants.

  7. [Chest Wall Reconstruction Using Titanium Plates Sandwiched Between Sheets after Resection of Chest Wall Chondrosarcoma].

    Science.gov (United States)

    Endoh, Makoto; Oizumi, Hiroyuki; Kato, Hirohisa; Suzuki, Jun; Watarai, Hikaru; Hamada, Akira; Suzuki, Katsuyuki; Takahashi, Ai; Nakahashi, Kenta; Sugawara, Masato; Tsuchiya, Takashi; Sadahiro, Mitsuaki

    2016-07-01

    Extensive chest wall resection carries the risk of difficult reconstruction and surgical complications. We report our experience on chest wall reconstruction using titanium plates for a wide thoracic defect after tumor resection. A 74-year-old man was diagnosed with chondrosarcoma of the 6th rib on the right. He needed extensive chest wall resection because of skip lesions on 4th rib noted on operative inspection, leaving a defect measuring 33 × 20 cm. Reconstruction using 5 transverse titanium plates sandwiched between an expanded polytetrafluoroethylene patch and a polypropylene mesh sheet stabilized the chest wall. This reconstruction allowed successful separation from ventilatory support after operation. The postoperative course was uneventful, and he was discharged on postoperative day 20. The advantages of this form of reconstruction over conventional prostheses are rigidity, and stability and usability.

  8. The Matrix Rib Plating System: improving aesthetic outcomes in microvascular breast reconstruction.

    Science.gov (United States)

    Ahdoot, Michael A; Echo, Anthony; Otake, Leo R; Son, Ji; Zeidler, Kamakshi R; Saadian, Isaac; Lee, Gordon K

    2013-04-01

    During microvascular breast reconstruction, exposure of internal mammary vessels (IMVs) is facilitated by the removal of a portion of the rib resulting in occasional chest contour deformity (CCD). The use of rib plating may reduce CCD and reduce postoperative pain. All patients underwent microvascular breast reconstruction using IMVs. In the retrospective arm, photographs were assessed by a blinded reviewer for CCDs. In the prospective cohort, patients were randomized to rib plating with the Synthes Matrix Rib Plating System or no rib plating. Postoperatively, patients were assessed for CCD and pain. In the retrospective arm, 11 of 98 (11.2%) patients representing 12 of 130 (9.2%) breast reconstructions had a noticeable contour deformity. The average body mass index (BMI) of patients with CCDs was 26.6 kg/m. In the prospective arm, there was 16% (3 of 19) rate of visible and palpable CCDs among controls, compared to 0% rate of palpable and visible contour deformity in the rib plating group. Pain was decreased in the rib plating group on all postoperative days. The pain reduction was statistically significant at rest by postoperative day 30. The majority of patients (9 of 11) with compromised aesthetic outcomes had a BMI less than 30 kg/m, suggesting a paucity of overlying soft tissue contributed to visibility of these bony defects. Rib plating prevented chest contour deformity, reduced postoperative pain, and added limited additional morbidity. We believe that rib plating is a safe, useful adjunct to microvascular breast reconstruction using IMVs, as it may improve aesthetic outcomes and reduce postoperative pain.

  9. Health-related quality of life after segmental resection of the lateral mandible: Free fibula flap versus plate reconstruction.

    Science.gov (United States)

    van Gemert, Johannes; Holtslag, Irene; van der Bilt, Andries; Merkx, Matthias; Koole, Ron; Van Cann, Ellen

    2015-06-01

    Segmental resection of the mandible causes functional, aesthetic and social problems affecting health-related quality of life (HRQoL). It is often assumed that reconstruction with composite free flaps guarantees better function and aesthetics than bridging the defect with reconstruction plates. Using the European Organization for Research and Treatment of Cancer questionnaires (EORTC QLQ-C30 version 3.0 and EORTC QLQ-H&N35), we compared HRQoL in patients who received free fibula flaps versus reconstruction plates after segmental resection of the lateral mandible. Thirty-seven completed questionnaires (18 fibula reconstructions and 19 patients with reconstruction plates) were available. Reconstruction with a free fibula flap did not provide clear additional benefit to bridging the defect with a reconstruction plate after segmental resection of the lateral mandible. In particular aspects known to have the most impact on HRQoL like swallowing, speech and chewing were not influenced by the type of reconstruction. Reconstruction of segmental defects of the lateral mandible with free fibula flap and reconstruction plate resulted in comparable HRQoL. If dental rehabilitation by means of dental implants is not anticipated in the fibula, then plate reconstruction with adequate soft tissue remains a suitable technique for the reconstruction of segmental defects of the lateral mandible. Copyright © 2015 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved.

  10. Finite element analysis of customized reconstruction plates for mandibular continuity defect therapy.

    Science.gov (United States)

    Narra, Nathaniel; Valášek, Jiří; Hannula, Markus; Marcián, Petr; Sándor, George K; Hyttinen, Jari; Wolff, Jan

    2014-01-03

    Large mandibular continuity defects pose a significant challenge in oral maxillofacial surgery. One solution to this problem is to use computer-guided surgical planning and additive manufacturing technology to produce patient-specific reconstruction plates. However, when designing customized plates, it is important to assess potential biomechanical responses that may vary substantially depending on the size and geometry of the defect. The aim of this study was to assess the design of two customized plates using finite element method (FEM). These plates were designed for the reconstruction of the lower left mandibles of two ameloblastoma cases (patient 1/plate 1 and patient 2/plate 2) with large bone resections differing in both geometry and size. Simulations revealed maximum von Mises stresses of 63 MPa and 108 MPa in plates 1 and 2, and 65 MPa and 190 MPa in the fixation screws of patients 1 and 2. The equivalent strain induced in the bone at the screw-bone interface reached maximum values of 2739 micro-strain for patient 1 and 19,575 micro-strain for patient 2. The results demonstrate the influence of design on the stresses induced in the plate and screw bodies. Of particular note, however, are the differences in the induced strains. Unphysiologically high strains in bone adjacent to screws can cause micro-damage leading to bone resorption. This can adversely affect the anchoring capabilities of the screws. Thus, while custom plates offer optimal anatomical fit, attention should be paid to the expected physiological forces on the plates and the induced stresses and strains in the plate-screw-bone assembly.

  11. Comparison of conventional reconstruction plate versus direct metal laser sintering plate: an in vitro mechanical characteristics study.

    Science.gov (United States)

    Xie, Pusheng; Ouyang, Hanbin; Deng, Yuping; Yang, Yang; Xu, Jing; Huang, Wenhua

    2017-09-02

    Additive manufacturing (AM) technology has helped to achieve several advances in the medical field, particularly as far as fabrication of implants is concerned. But the application of direct metal laser sintering (DMLS) bone plate is quite limited due to the indeterminate mechanical property. The purposes of this study were to characterize the biomechanical properties of the polished DMLS reconstruction plate and to compare these with the properties of commonly applied implants and to find whether the mechanical performance of DMLS plate meets the requirements for clinical application. In this study, we fabricated two groups of plates by DMLS and computer numerical control (CNC) techniques. After that, we polished all samples and investigated their roughness, components, hardness, static bending, and torsional performance. Moreover, cyclic bending tests and fractographic analysis were conducted. Statistical comparisons of the group by means of monotonic test data were made, and a qualitative comparison was performed to assess failures in fatigue. We found no differences in surface roughness or components after polishing, but the DMLS plate hardness is 7.42% (p direct application of these AM instruments in the operating room requires further validation including animal and clinical experiment.

  12. Closure of the Africa-Eurasia-North America plate motion circuit and tectonics of the Gloria fault

    Science.gov (United States)

    Argus, Donald F.; Gordon, Richard G.; Demets, Charles; Stein, Seth

    1989-01-01

    The current motions of the African, Eurasian, and North American plates are examined. The problems addressed include whether there is resolvable motion of a Spitsbergen microplate, the direction of motion between the African and North American plates, whether the Gloria fault is an active transform fault, and the implications of plate circuit closures for rates of intraplate deformation. Marine geophysical data and magnetic profiles are used to construct a model which predicts about 4 mm/yr slip across the Azores-Gibraltar Ridge, and west-northwest convergence near Gibraltar. The analyzed data are consistent with a rigid plate model with the Gloria fault being a transform fault.

  13. Dictionary-based image reconstruction for superresolution in integrated circuit imaging.

    Science.gov (United States)

    Cilingiroglu, T Berkin; Uyar, Aydan; Tuysuzoglu, Ahmet; Karl, W Clem; Konrad, Janusz; Goldberg, Bennett B; Ünlü, M Selim

    2015-06-01

    Resolution improvement through signal processing techniques for integrated circuit imaging is becoming more crucial as the rapid decrease in integrated circuit dimensions continues. Although there is a significant effort to push the limits of optical resolution for backside fault analysis through the use of solid immersion lenses, higher order laser beams, and beam apodization, signal processing techniques are required for additional improvement. In this work, we propose a sparse image reconstruction framework which couples overcomplete dictionary-based representation with a physics-based forward model to improve resolution and localization accuracy in high numerical aperture confocal microscopy systems for backside optical integrated circuit analysis. The effectiveness of the framework is demonstrated on experimental data.

  14. Predictive factors for premature loss of Martin 2.7 mandibular reconstruction plates

    NARCIS (Netherlands)

    van der Rijt, E. E. M.; Noorlag, R.; Koole, R.; Abbink, J. H.; Rosenberg, A. J. W. P.

    Mandibular reconstruction with a plate, with or without a vascularised free (bone) flap, is commonly used to treat patients with a segmental mandibular defect. Common complications are loosening of the osteosynthesis screws, malposition, intraoral or extraoral exposure, or infection. To define

  15. The Role of Resorbable Plate and Artificial Bone Substitute in Reconstruction of Large Orbital Floor Defect

    Directory of Open Access Journals (Sweden)

    Ho Kwon

    2016-01-01

    Full Text Available It is essential to reduce and reconstruct bony defects adequately in large orbital floor fracture and defect. Among many reconstructive methods, alloplastic materials have attracted attention because of their safety and ease of use. We have used resorbable plates combined with artificial bone substitutes in large orbital floor defect reconstructions and have evaluated their long-term reliability compared with porous polyethylene plate. A total of 147 patients with traumatic orbital floor fracture were included in the study. Surgical results were evaluated by clinical evaluations, exophthalmometry, and computed tomography at least 12 months postoperatively. Both orbital floor height discrepancy and orbital volume change were calculated and compared with preoperative CT findings. The average volume discrepancy and vertical height discrepancies were not different between two groups. Also, exophthalmometric measurements were not significantly different between the two groups. No significant postoperative complication including permanent diplopia, proptosis, and enophthalmos was noted. Use of a resorbable plate with an artificial bone substitute to repair orbital floor defects larger than 2.5 cm2 in size yielded long-lasting, effective reconstruction without significant complications. We therefore propose our approach as an effective alternative method for large orbital floor reconstructions.

  16. Shrinking of the Cocos and Nazca Plates due to Horizontal Thermal Contraction and Implications for Plate Non-rigidity and the Non-closure of the Pacific-Cocos-Nazca Plate Motion Circuit

    Science.gov (United States)

    Gordon, R. G.; Kreemer, C.

    2015-12-01

    Plate rigidity is the central tenet of plate tectonics. Mounting evidence suggests, however, that significant intraplate deformation occurs in oceanic lithosphere due to horizontal thermal contraction, the rate of which decreases as ≈ 1/age [Kumar & Gordon 2009]. Support for this hypothesis comes from the azimuths of submarine transform faults, which are fit significantly better assuming shrinking plates than by assuming rigid plates [Mishra & Gordon 2015]. Previously we estimated the intraplate velocity field of the Pacific plate accounting for horizontal thermal contraction. The ≈2 mm/yr southeastward motion predicted for the northeastern part of the plate relative to the Pacific-Antarctic Rise may contribute to the non-closure of the Pacific-North America plate motion circuit. In a reference frame in which fix the oldest portion of the Pacific plate, some sites on the plate move up to ≈2 mm/yr [Kreemer & Gordon 2014]. Here we present intraplate velocity fields of the Cocos and Nazca plates and discuss their implications for the non-rigidity of plates and the non-closure of the Pacific-Cocos-Nazca plate circuit, which fails closure by a stunning 14 ±5 mm/yr [DeMets et al. 2010]. If we fix the oldest part of the Cocos plate, intraplate velocities of up to ≈2 mm/yr are estimated, with the fastest motion occurring at the northern end of the plate. If we fix the oldest part of the Nazca plate, displacement rates up to 2 mm/yr are estimated, with the fastest motion occurring in the northeasternmost portion of the plate. In the velocity fields for both plates, the lithosphere adjacent to transform faults along the East Pacific Rise tends to move to the south, which would skew the azimuths of the transform faults clockwise of the values expected for rigid plates, which is the same as the sense of misfit between observed azimuths of transform faults and the azimuths calculated from the MORVEL global set of relative angular velocities [DeMets et al. 2010]. Direct

  17. Equivalent circuit modeling of a piezo-patch energy harvester on a thin plate with AC-DC conversion

    Science.gov (United States)

    Bayik, B.; Aghakhani, A.; Basdogan, I.; Erturk, A.

    2016-05-01

    As an alternative to beam-like structures, piezoelectric patch-based energy harvesters attached to thin plates can be readily integrated to plate-like structures in automotive, marine, and aerospace applications, in order to directly exploit structural vibration modes of the host system without mass loading and volumetric occupancy of cantilever attachments. In this paper, a multi-mode equivalent circuit model of a piezo-patch energy harvester integrated to a thin plate is developed and coupled with a standard AC-DC conversion circuit. Equivalent circuit parameters are obtained in two different ways: (1) from the modal analysis solution of a distributed-parameter analytical model and (2) from the finite-element numerical model of the harvester by accounting for two-way coupling. After the analytical modeling effort, multi-mode equivalent circuit representation of the harvester is obtained via electronic circuit simulation software SPICE. Using the SPICE software, electromechanical response of the piezoelectric energy harvester connected to linear and nonlinear circuit elements are computed. Simulation results are validated for the standard AC-AC and AC-DC configurations. For the AC input-AC output problem, voltage frequency response functions are calculated for various resistive loads, and they show excellent agreement with modal analysis-based analytical closed-form solution and with the finite-element model. For the standard ideal AC input-DC output case, a full-wave rectifier and a smoothing capacitor are added to the harvester circuit for conversion of the AC voltage to a stable DC voltage, which is also validated against an existing solution by treating the single-mode plate dynamics as a single-degree-of-freedom system.

  18. Impact of uncertain reference-frame motions in plate kinematic reconstructions: A theoretical appraisal

    Science.gov (United States)

    Iaffaldano, Giampiero; Stein, Seth

    2017-01-01

    Geoscientists infer past plate motions, which serve as fundamental constraints for a range of studies, from observations of magnetic isochrons as well as hotspots tracks on the ocean floor and, for stages older than the Cretaceous, from paleomagnetic data. These observations effectively represent time-integrals of past plate motions but, because they are made at present, yield plate kinematics naturally tied to a present-day reference-frame, which may be another plate or a hotspots system. These kinematics are therefore different than those occurred at the time when the rocks acquired their magnetisation or when hotspot-related marine volcanism took place, and are normally corrected for the reference-frame absolute motion (RFAM) that occurred since then. The impact of true-polar-wander events on paleomagnetic data and the challenge of inferring hotspot drifts result in RFAMs being less resolved - in a temporal sense - and prone to noise. This limitation is commonly perceived to hamper the correction of plate kinematic reconstructions for RFAMs, but the extent to which this may be the case has not been explored. Here we assess the impact of uncertain RFAMs on kinematic reconstructions using synthetic models of plate motions over 100 million years. We use randomly-drawn models for the kinematics of two plates separated by a spreading ridge to generate a synthetic magnetisation pattern of the ocean floor. The kinematics we infer from such a pattern are outputs that we correct for synthetic RFAMs using two equivalent methods (a classical one as well as another that we propose and test here) and then compare to the 'true' motions input. We assess the misfits between true and inferred kinematics by exploring a statistically-significant number of models where we systematically downgrade the temporal resolution of RFAM synthetic data and add noise to them. We show that even poorly-resolved, noisy RFAMs are sufficient to retrieve reliable plate kinematic reconstructions

  19. Coda reconstruction from cross-correlation of a diffuse field on thin elastic plates

    Science.gov (United States)

    Hejazi Nooghabi, Aida; Boschi, Lapo; Roux, Philippe; de Rosny, Julien

    2017-09-01

    This study contributes to the evaluation of the robustness and accuracy of Green's function reconstruction from cross-correlation of strongly dispersed reverberated signals, with disentangling of the respective roles of ballistic and reverberated ("coda") contributions. We conduct a suite of experiments on a highly reverberating thin duralumin plate, where an approximately diffuse flexural wave field is generated by taking advantage of the plate reverberation and wave dispersion. A large number of impulsive sources that cover the whole surface of the plate are used to validate ambient-noise theory through comparison of the causal and anticausal (i.e., positive- and negative-time) terms of the cross-correlation to one another and to the directly measured Green's function. To quantify the contribution of the ballistic and coda signals, the cross-correlation integral is defined over different time windows of variable length, and the accuracy of the reconstructed Green's function is studied as a function of the initial and end times of the integral. We show that even cross-correlations measured over limited time windows converge to a significant part of the Green's function. Convergence is achieved over a wide time window, which includes not only direct flexural-wave arrivals, but also the multiply reverberated coda. We propose a model, based on normal-mode analysis, that relates the similarity between the cross-correlation and the Green's function to the statistical properties of the plate. We also determine quantitatively how incoherent noise degrades the estimation of the Green's function.

  20. Multimodal sparse reconstruction in guided wave imaging of defects in plates

    Science.gov (United States)

    Golato, Andrew; Santhanam, Sridhar; Ahmad, Fauzia; Amin, Moeness G.

    2016-07-01

    A multimodal sparse reconstruction approach is proposed for localizing defects in thin plates in Lamb wave-based structural health monitoring. The proposed approach exploits both the sparsity of the defects and the multimodal nature of Lamb wave propagation in plates. It takes into account the variation of the defects' aspect angles across the various transducer pairs. At low operating frequencies, only the fundamental symmetric and antisymmetric Lamb modes emanate from a transmitting transducer. Asymmetric defects scatter these modes and spawn additional converted fundamental modes. Propagation models are developed for each of these scattered and spawned modes arriving at the various receiving transducers. This enables the construction of modal dictionary matrices spanning a two-dimensional array of pixels representing potential defect locations in the region of interest. Reconstruction of the region of interest is achieved by inverting the resulting linear model using the group sparsity constraint, where the groups extend across the various transducer pairs and the different modes. The effectiveness of the proposed approach is established with finite-element scattering simulations of the fundamental Lamb wave modes by crack-like defects in a plate. The approach is subsequently validated with experimental results obtained from an aluminum plate with asymmetric defects.

  1. Corrosion Behavior of Silver-Plated Circuit Boards in a Simulated Marine Environment with Industrial Pollution

    Science.gov (United States)

    Xiao, Kui; Yi, Pan; Yan, Lidan; Bai, Ziheng; Dong, Chaofang; Dong, Pengfei; Gao, Xiong

    2017-01-01

    The electrochemical corrosion behavior of a silver-plated circuit board (PCB-ImAg) in a polluted marine atmosphere environment (Qingdao in China) is studied through a simulated experiment. The morphologies of PCB-ImAg show some micropores on the surface that act as the corrosion-active points in the tests. Cl− mainly induces microporous corrosion, whereas SO2 causes general corrosion. Notably, the silver color changes significantly under SO2 influence. EIS results show that the initial charge transfer resistance in the test containing SO2 and Cl− is 9.847 × 103, while it is 3.701 × 104 in the test containing Cl− only, which demonstrates that corrosion accelerates in a mixed atmosphere. Polarization curves further show that corrosion potential is lower in mixed solutions (between −0.397 V SCE and −0.214 V SCE) than it in the solution containing Cl− only (−0.168 V SCE), indicating that corrosion tendency increases with increased HSO3− concentration. PMID:28773121

  2. Cytotoxicity difference of 316L stainless steel and titanium reconstruction plate

    Directory of Open Access Journals (Sweden)

    Ni Putu Mira Sumarta

    2011-03-01

    Full Text Available Background: Pure titanium is the most biocompatible material today and used as a gold standard for metallic implants. However, stainless steel is still being used as implants because of its strength, ductility, lower price, corrosion resistant and biocompatibility. Purpose: This study was done to revealed the cytotoxicity difference between reconstruction plate made of 316L stainless steel and of commercially pure (CP titanium in baby hamster kidney-21 (BHK-21 fibroblast culture through MTT assay. Methods: Eight samples were prepared from reconstruction plates made of stainless steel type 316L grade 2 (Coen’s reconstruction plate® that had been cut into cylindrical form of 2 mm in diameter and 3 mm long. The other one were made of CP titanium (STEMA Gmbh® of 2 mm in diameter and 2,2 mm long; and had been cleaned with silica paper and ultrasonic cleaner, and sterilized in autoclave at 121° C for 20 minutes.9 Both samples were bathed into microplate well containing 50 μl of fibroblast cells with 2 x 105 density in Rosewell Park Memorial Institute-1640 (RPMI-1640 media, spinned at 30 rpm for 5 minutes. Microplate well was incubated for 24 and 48 hours in 37° C. After 24 hours, each well that will be read at 24 hour were added with 50 μl solution containing 5mg/ml MTT reagent in phosphate buffer saline (PBS solutions, then reincubated for 4 hours in CO2 10% and 37° C. Colorometric assay with MTT was used to evaluate viability of the cells population after 24 hours. Then, each well were added with 50 μl dimethyl sulfoxide (DMSO and reincubated for 5 minutes in 37° C. the wells were read using Elisa reader in 620 nm wave length. Same steps were done for the wells that will be read in 48 hours. Each data were tabulated and analyzed using independent T-test with significance of 5%. Results: This study showed that the percentage of living fibroblast after exposure to 316L stainless steel reconstruction plate was 61.58% after 24 hours and 62

  3. New Paleomagnetic Justification for the Plate Tectonic Reconstruction of the Arctic

    Science.gov (United States)

    Metelkin, D. V.; Vernikovskiy, V. A.; Matushkin, N. Y.; Zhdanova, A.; Mikhaltsov, N. E.; Abashev, V. V.; Kulakov, E.

    2015-12-01

    We report paleomagnetic and geologic data that support a new plate tectonic reconstruction for the Arctic from the Neoproterozoic to Mesozoic. We propose a new outlook on the history of the Arctida paleocontinent, which combined sialic blocks of the present Eurasian shelf of the Arctic Ocean. Our model implies two Arctidas at that time. The earlier Arctida-I was located near equator and connected the continental margins of Laurentia, Baltica and Siberia within the supercontinent of Rodinia. The Arcrtida-I disintegration was caused by a breakup of Rodinia. As a result, small plates like on Svalbard, Kara, New Siberia Island (NSI) terrane and others were formed. We have reconstructed the main stages of later remobilization and global drift of these plates before Pangea assemblage. In contrast to traditional interpretation of the NSI as a part of the Chukchi-Alaska terrane, our observation suggest a linkage between the NSI and Kolyma-Omolon terrane that framed Siberia. As a result of Pangea assembly at Paleozoic-Mesozoic boundary the second recovery of Arctida took place. We assume that Arctida-II also connected Laurentia, Baltica, and Siberia but constituted the Pangean periphery in the temperate latitudes. The later Arctida-II disintegrated during the Mesozoic during the opening of Arctic Ocean.

  4. The Proto Southern Gulf of California represented by GIS Plate Tectonic Reconstructions

    Science.gov (United States)

    Skinner, L. A.; Umhoefer, P. J.; Kluesner, J. W.

    2012-12-01

    We present GIS-based plate tectonic reconstruction maps for the southern Gulf of California oblique rift. The maps track plate boundary deformation back to 14 Ma. Tectonic blocks are defined by faults, geology, seismic data, and bathymetry/topography. Spreading center and fault-slip rates were acquired from geologic data, cross-Gulf tie points, and GPS studies. Baja California-North America GPS rates (47 mm/yr across the Gulf; 4 mm/yr in the borderland) agree remarkably with ~6 Ma geologic offsets across the Gulf and are used during reconstruction steps back to 6 Ma. The Alarcon and Guaymas spreading centers initiated at 2.4 Ma and 6 Ma (Lizarralde et al., 2007), respectively, while the Farallon, Pescadero, and Carmen spreading centers began between ~2-1 Ma (Lonsdale, 1989). Therefore, the 2, 4, and 6 Ma reconstruction steps include a long transtensional fault zone along much of the southern Gulf, connecting the Guaymas spreading center with either the Alarcon spreading center or East Pacific Rise. For reconstructions at 8, 10, and 12 Ma, a range of across-Gulf and borderland fault rates fit the current constraints, but all models suggest an increase in across-Gulf faulting rates at 8 - 6 Ma. We used 30 mm/yr across the Gulf and 20 mm/yr across the borderland. These models result in ~470 km northwestward offset across the Gulf (we also account for a minor E-W offset) and ~145 km offset across the borderland. The 12 - 14 Ma reconstructions suggest that the Gulf of California formed along a 100 x 1600 km volcanic arc and narrow extensional belt between the Cretaceous batholith and the Sierra Madre Occidental. The initial seaway at 8 - 6.5 Ma was only ~200-250 km wide by 1600 km long. We will also combine our 12 Ma map with the McQuarrie and Werrnicke (2005) reconstruction to present a new reconstruction for the whole Walker Lane to Gulf of California belt.

  5. Reconstruction of Dispersive Lamb Waves in Time Plates Using a Time Reversal Method

    Energy Technology Data Exchange (ETDEWEB)

    Jeong, Hyun Jo [Wonkwang University, Iksan (Korea, Republic of)

    2008-02-15

    Time reversal (TR) of nondispersive body waves has been used in many applications including ultrasonic NDE. However, the study of the TR method for Lamb waves on thin structures is not well established. In this paper, the full reconstruction of the input signal is investigated for dispersive Lamb waves by introducing a time reversal operator based on the Mindlin plate theory. A broadband and a narrowband input waveform are employed to reconstruct the A{sub 0} mode of Lamb wave propagations. Due to the frequency dependence of the TR process of Lamb waves, different frequency components of the broadband excitation are scaled differently during the time reversal process and the original input signal cannot be fully restored. This is the primary reason for using a narrowband excitation to enhance the flaw detectability

  6. Comparison of results between hook plate fixation and ligament reconstruction for acute unstable acromioclavicular joint dislocation.

    Science.gov (United States)

    Yoon, Jong Pil; Lee, Byoung-Joo; Nam, Sang Jin; Chung, Seok Won; Jeong, Won-Ju; Min, Woo-Kie; Oh, Joo Han

    2015-03-01

    In the present study, we aimed to compare clinical and radiographic outcomes between hook plate fixation and coracoclavicular (CC) ligament reconstruction for the treatment of acute unstable acromioclavicular (AC) joint dislocation. Forty-two patients who underwent surgery for an unstable acute dislocation of the AC joint were included. We divided them into two groups according to the treatment modality: internal fixation with a hook plate (group I, 24 cases) or CC ligament reconstruction (group II, 18 cases). We evaluated the clinical outcomes using a visual analog scale (VAS) for pain and Constant-Murley score, and assessed the radiographic outcomes based on the reduction and loss of CC distance on preoperative, postoperative, and final follow-up plain radiographs. The mean VAS scores at the final follow-up were 1.6 ± 1.5 and 1.3 ± 1.3 in groups I and II, respectively, which were not significantly different. The mean Constant-Murley scores were 90.2 ± 9.9 and 89.2 ± 3.5 in groups I and II, respectively, which were also not significantly different. The AC joints were well reduced in both groups, whereas CC distance improved from a mean of 215.7% ± 50.9% preoperatively to 106.1% ± 10.2% at the final follow-up in group I, and from 239.9% ± 59.2% preoperatively to 133.6% ± 36.7% at the final follow-up in group II. The improvement in group I was significantly superior to that in group II (p < 0.001). Furthermore, subluxation was not observed in any case in group I, but was noted in six cases (33%) in group II. Erosions of the acromion undersurface were observed in 9 cases in group I. In cases of acute unstable AC joint dislocation, hook plate fixation and CC ligament reconstruction yield comparable satisfactory clinical outcomes. However, radiographic outcomes based on the maintenance of reduction indicate that hook plate fixation is a better treatment option.

  7. Valgus osteotomy of the tibia with a Puddu plate combined with anterior cruciate ligament reconstruction

    Directory of Open Access Journals (Sweden)

    Albuquerque Roberto Freire da Mota e

    2003-01-01

    Full Text Available Anterior knee instability associated with a varus deformity is a complex condition with several treatment possibilities. Among these, anterior cruciate ligament (ACL associated to a simultaneous valgus tibial osteotomy is a increasing indication. This simultaneous procedure adds technical issues to those related to the isolated surgeries. Thus, the osteotomy plane and location of fixation hardware shouldn?t conflict with tibial tunnel and ACL graft fixation. Authors analyze the relations between a opening tibial valgus osteotomy stabilized with a Puddu plate and ACL reconstruction with a patellar tendon graft fixated with interference screws in 10 human cadaver knees. A straight oblique tibial osteotomy starting on the medial tibial cortex and oriented laterally and proximally was performed on all knees with a 10mm opening medially and stabilized with a Puddu plate on the most posterior aspect of the medial tibia, and a tibial tunnel drilled 50° to tibial plateau. With this technique there was no intersection between tibial tunnel or interference screw and the osteotomy or the plate fixation screws.

  8. Inherited segmentation of the Iberian-African margins and tectonic reconstruction of a diffuse plate boundary.

    Science.gov (United States)

    Fernàndez, Manel; Torne, Montserrat; Vergés, Jaume; Casciello, Emilio

    2016-04-01

    Diffuse plate-boundary regions are characterized by non-well defined contacts between tectonic plates thus making difficult their reconstruction through time. The Western Mediterranean is one of these regions, where the convergence between the African and Iberian plates since Late Cretaceous resulted in the Betic-Rif arcuate orogen, the Gulf of Cadiz imbricate wedge, and the Alboran back-arc basin. Whereas the Iberia-Africa plate boundary is well defined west to the Gorringe Bank and along the Gloria Fault, it becomes much more diffuse eastwards with seismicity spreading over both the south-Iberian and north-African margins. Gravity data, when filtered for short wavelengths, show conspicuous positive Bouguer anomalies associated with the Gorringe Bank, the Gulf of Cadiz High and the Ronda/Beni-Bousera peridotitic massifs reflecting an inherited Jurassic margin segmentation. The subsequent Alpine convergence between Africa and Iberia reactivated these domains, producing crustal-scale thrusting in the Atlantic segments and eventually subduction in the proto-Mediterranean segments. The Jurassic segmentation of the Iberia-Africa margins substantiates the double-polarity subduction model proposed for the region characterized by a change from SE-dipping polarity in the Gorringe, Gulf of Cadiz and Betic-Rif domains, to NW-dipping polarity in the proto-Algerian domain. Therefore, the Algerian and Tyrrhenian basins in the east and the Alboran basin in the west are the result of SSE-E and NW-W retreating slabs of oceanic and/or hyper-extended Tethyan domains, respectively.

  9. Surgical planning and microvascular reconstruction of the mandible with a fibular flap using computer-aided design, rapid prototype modelling, and precontoured titanium reconstruction plates: a prospective study.

    Science.gov (United States)

    Sieira Gil, R; Roig, A Marí; Obispo, C Arranz; Morla, A; Pagès, C Martí; Perez, J Llopis

    2015-01-01

    The standard of mandibular reconstruction has increased since the introduction of computer-assisted design (CAD) and rapid prototype modelling (RPM) for surgical planning. Between 2008 and 2013, a prospective pilot study of 20 patients was planned to compare the outcomes of patients treated by mandibular reconstruction who had CAD and RPM-guided operations using a precontoured titanium plate, with the outcomes of patients treated conventionally. We recorded the time taken for reconstruction, total operating time, and whether this type of planning could improve the results of mandibular reconstruction. We found significant differences in the incidence of dental malocclusion (p=0.03) and exposure of the titanium plate (p=0.009). The mean operating time for reconstruction in the preoperative planning group was 135 (37)min compared with 176 (58)min in the conventional group (p=0.04). Preoperative planning using CAD and RPM can increase the accuracy of microvascular mandibular reconstruction and reduce the operating time for reconstruction. Copyright © 2014 The British Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

  10. Development of nondestructive testing techniques for plated-through holes in multilayer printed circuit boards

    Science.gov (United States)

    Anthony, P. L.; Mcmurtrey, J. E.

    1971-01-01

    The development of a nondestructive test with the capability to interrogate plated-through holes as small as 0.51 millimeters inside diameter is discussed. The system can detect defects such as holes, voids, cracks, and thin spots that reduce the current carrying capability of plates-through interconnects by 20 percent or more. Efforts were directed toward the design and fabrication of magnetic circuitry mutual coupling probes and to evaluate the effectiveness of these devices for detecting in multilayer board plated-through holes.

  11. Combined finite element and multibody musculoskeletal investigation of a fractured clavicle with reconstruction plate

    DEFF Research Database (Denmark)

    Cronskar, Marie; Rasmussen, John; Tinnsten, Mats

    2015-01-01

    This paper addresses the various treatment options for clavicle fractures by means of computational models, more precisely cases with a need for internal fixation: non-unions and certain complex fractures. The motivation for the work is that treatment can be enhanced by a better understanding...... of the loading of the clavicle and fixation device. This study aimed to develop a method for realistic simulation of stresses in the bone and fixation device in the case of a fractured clavicle. A finite element (FE) mesh of the clavicle geometry was created from computer tomography (CT) data and imported...... into the FE solver where the model was subjected to muscle forces and other boundary conditions from a multibody musculoskeletal model performing a typical activity of daily life. A reconstruction plate and screws were also imported into the model. The combination models returned stresses and displacements...

  12. Serial Section Registration of Axonal Confocal Microscopy Datasets for Long-Range Neural Circuit Reconstruction

    Energy Technology Data Exchange (ETDEWEB)

    Hogrebe, Luke; Paiva, Antonio R.; Jurrus, Elizabeth R.; Christensen, Cameron; Bridge, Michael; Dai, Li; Pfeiffer, Rebecca; Hof, Patrick; Roysam, Badrinath; Korenberg, Julie; Tasdizen, Tolga

    2012-06-15

    In the context of long-range digital neural circuit reconstruction, this paper investigates an approach for registering axons across histological serial sections. Tracing distinctly labeled axons over large distances allows neuroscientists to study very explicit relationships between the brain's complex interconnects and, for example, diseases or aberrant development. Large scale histological analysis requires, however, that the tissue be cut into sections. In immunohistochemical studies thin sections are easily distorted due to the cutting, preparation, and slide mounting processes. In this work we target the registration of thin serial sections containing axons. Sections are first traced to extract axon centerlines, and these traces are used to define registration landmarks where they intersect section boundaries. The trace data also provides distinguishing information regarding an axon's size and orientation within a section. We propose the use of these features when pairing axons across sections in addition to utilizing the spatial relationships amongst the landmarks. The global rotation and translation of an unregistered section are accounted for using a random sample consensus (RANSAC) based technique. An iterative nonrigid refinement process using B-spline warping is then used to reconnect axons and produce the sought after connectivity information.

  13. Avoiding short circuits from zinc metal dendrites in anode by backside-plating configuration

    OpenAIRE

    Higashi, Shougo; Lee, Seok Woo; Lee, Jang Soo; Takechi, Kensuke; Cui, Yi

    2016-01-01

    Portable power sources and grid-scale storage both require batteries combining high energy density and low cost. Zinc metal battery systems are attractive due to the low cost of zinc and its high charge-storage capacity. However, under repeated plating and stripping, zinc metal anodes undergo a well-known problem, zinc dendrite formation, causing internal shorting. Here we show a backside-plating configuration that enables long-term cycling of zinc metal batteries without shorting. We demonst...

  14. A millimeter-wave integrated-circuit antenna based on the Fresnel zone plate

    Science.gov (United States)

    Gouker, Mark A.; Smith, Glenn S.

    1992-05-01

    A moderate-gain, easily constructed, millimeter-wave IC antenna based on the Fresnel zone plate has been developed. The gain and beamwidth of the antenna can be varied by adjusting the diameter and focal length of the zone plate. A theory is developed which accurately predicts the on-axis gain, beamwidth, and sidelobe levels of antennas with zone-plate focal lengths greater than 8-9 lambda. Graphs are presented to aid in the design of other IC zone-plate antennas. The performance of the antenna without the reflector and lambda/4 spacer was investigated. The gain of the antenna with nothing behind the zone plate is found to approach that of the fully configured antenna with the lambda/4 spacer and reflector. The reflection from the open rings which is responsible for this phenomenon is enhanced as the dielectric constant of the substrate is increased. Thus, on substrates with high permittivity the reflector and lambda/4 spacer may not be necessary.

  15. Time variability in Cenozoic reconstructions of mantle heat flow: plate tectonic cycles and implications for Earth's thermal evolution.

    Science.gov (United States)

    Loyd, S J; Becker, T W; Conrad, C P; Lithgow-Bertelloni, C; Corsetti, F A

    2007-09-04

    The thermal evolution of Earth is governed by the rate of secular cooling and the amount of radiogenic heating. If mantle heat sources are known, surface heat flow at different times may be used to deduce the efficiency of convective cooling and ultimately the temporal character of plate tectonics. We estimate global heat flow from 65 Ma to the present using seafloor age reconstructions and a modified half-space cooling model, and we find that heat flow has decreased by approximately 0.15% every million years during the Cenozoic. By examining geometric trends in plate reconstructions since 120 Ma, we show that the reduction in heat flow is due to a decrease in the area of ridge-proximal oceanic crust. Even accounting for uncertainties in plate reconstructions, the rate of heat flow decrease is an order of magnitude faster than estimates based on smooth, parameterized cooling models. This implies that heat flow experiences short-term fluctuations associated with plate tectonic cyclicity. Continental separation does not appear to directly control convective wavelengths, but rather indirectly affects how oceanic plate systems adjust to accommodate global heat transport. Given that today's heat flow may be unusually low, secular cooling rates estimated from present-day values will tend to underestimate the average cooling rate. Thus, a mechanism that causes less efficient tectonic heat transport at higher temperatures may be required to prevent an unreasonably hot mantle in the recent past.

  16. Madagascar's escape from Africa: A high-resolution plate reconstruction for the Western Somali Basin and implications for supercontinent dispersal

    Science.gov (United States)

    Phethean, Jordan J. J.; Kalnins, Lara M.; van Hunen, Jeroen; Biffi, Paolo G.; Davies, Richard J.; McCaffrey, Ken J. W.

    2016-12-01

    Accurate reconstructions of the dispersal of supercontinent blocks are essential for testing continental breakup models. Here, we provide a new plate tectonic reconstruction of the opening of the Western Somali Basin during the breakup of East and West Gondwana. The model is constrained by a new comprehensive set of spreading lineaments, detected in this heavily sedimented basin using a novel technique based on directional derivatives of free-air gravity anomalies. Vertical gravity gradient and free-air gravity anomaly maps also enable the detection of extinct mid-ocean ridge segments, which can be directly compared to several previous ocean magnetic anomaly interpretations of the Western Somali Basin. The best matching interpretations have basin symmetry around the M0 anomaly; these are then used to temporally constrain our plate tectonic reconstruction. The reconstruction supports a tight fit for Gondwana fragments prior to breakup, and predicts that the continent-ocean transform margin lies along the Rovuma Basin, not along the Davie Fracture Zone (DFZ) as commonly thought. According to our reconstruction, the DFZ represents a major ocean-ocean fracture zone formed by the coalescence of several smaller fracture zones during evolving plate motions as Madagascar drifted southwards, and offshore Tanzania is an obliquely rifted, rather than transform, margin. New seismic reflection evidence for oceanic crust inboard of the DFZ strongly supports these conclusions. Our results provide important new constraints on the still enigmatic driving mechanism of continental rifting, the nature of the lithosphere in the Western Somali Basin, and its resource potential.

  17. Application of non-cyanide gold for selective plating of microelectronic circuits

    Energy Technology Data Exchange (ETDEWEB)

    Worobey, W.; Rieger, D.

    1991-01-01

    With the current trends towards miniaturization, high performance, high quality and cost competiveness, the electrodeposition process has become an important manufacturing technology in many new microelectronic applications. Gold electrodeposition plays an increasing role in processes that require this noble metal. Added to these trends is the continuing and increasing emphasis on manufacturing processes which are less damaging to the environment and potentially less hazardous to the operator and personnel in the vicinity of the operation. The present standard gold plating solutions are based on cyanide salts and are considered acutely hazardous solutions. The trend away from their use is gaining momentum as new non-hazardous gold plating solutions and manufacturing processes making use of them are developed. 2 refs.

  18. The free vascularized flap and the flap plate options: comparative results of reconstruction of lateral mandibular defects.

    Science.gov (United States)

    Shpitzer, T; Gullane, P J; Neligan, P C; Irish, J C; Freeman, J E; Van den Brekel, M; Gur, E

    2000-12-01

    Reconstruction of the mandible and oral cavity after segmental resection is a challenging surgical problem. Although osteocutaneous free flaps are generally accepted to be optimal for reconstruction of anterior defects, the need for bony reconstruction for a pure lateral mandibular defect remains controversial. A retrospective study. A retrospective comparative study of short- and long-term outcomes of three different reconstruction techniques for lateral defects was performed. In total, 57 patients were included, of whom 27 had a plate and pedicled pectoralis major myocutaneous flap (PMMF group), 16 had a plate and free radial forearm flap (FRFF group), and 14 had an osteocutaneous free flap. Functionality, flap failure, and complications were scored. Plates had to be removed in 7 of the 27 patients in the PMMF group and 2 of the 16 in the FRFF group; none of the 14 osteocutaneous free flaps failed. The difference was of borderline statistical significance (P = .055). Longterm functional outcome revealed no statistically significant difference in oral deglutition (P = .76) or in facial contour (P = .36). Oral continence was significantly better in patients in the FRFF group (88%) as compared with the PMMF group (52%) or the osteocutaneous free flap group (43%) (P = .02). On the other hand, the results for speech favored the osteocutaneous free flap group; 13 of 14 patients (92.9%) had a normal score compared with 12 of 16 patients (75%) in the FRFF group and 17 of 27 (63%) in the PMMF group. However, this represented a borderline statistically significant result (P = .06). For lateral mandibular defects, the osteocutaneous free flap is reliable and durable in the long term. However, in a selected group of patients either of the two flap-plate options is a viable reconstructive option.

  19. Neoproterozoic-Paleozoic Evolution of the Arctida Paleocontinent and Plate Reconstructions

    Science.gov (United States)

    Vernikovsky, V. A.; Metelkin, D. V.; Vernikovskaya, A. E.; Matushkin, N. Y.; Lobkovsky, L. I.; Shipilov, E. V.; Scientific Team of Arctida

    2011-12-01

    Available data on the existence of Precambrian metamorphic complexes among the main structures of the Arctic led to the suggestion that a large continental mass existed between Laurentia, Baltica and Siberia - an Arctic continent, more often called Arctida (Zonenshain, Natapov, 1987). It is inferred that as an independent continental mass Arctida was formed after the breakup of Rodinia, and in general it can have a pre-Grenvillian (including Grenvillian) basement age. The breakup of this mass and the collision of its fragments with adjacent cratons led to the formation of heterochronous collisional systems. Arctida probably included the Kara, Novosibirsk, Alaska-Chukotka blocks, the blocks of northern Alaska and the submerged Lomonosov Ridge, small fragments of the Inuit fold belt in the north of Greenland and the Canadian archipelago, the structures of the Svalbard and maybe the Timan-Pechora plates. However the inner structure of this paleocontinent, the mutual configuration of the blocks and its evolution in the Neoproterozoic-Paleozoic is still a matter of discussion. The most accurate way of solving these issues is by using paleomagnetic data, but those are nonexistent for most of the defined blocks. Reliable paleomagnetic determinations for the Neoproterozoic-Paleozoic time interval we are concerned with are available only for fragments of an island arc from Central Taimyr, which are 960 m.y. old (Vernikovsky et al., 2011) and for which the paleomagnetic pole is very close to the pole of Siberia from (Pavlov et al., 2002), and of the Kara microcontinent. This includes three paleomagnetic poles for 500, 450 and 420 Ma (Metelkin et al., 2000; Metelkin et al., 2005). It is those data that made up the basis of the presented paleotectonic reconstructions along with an extensive paleomagnetic database for the cratons of Laurentia, Baltica, Siberia and Gondwana. The paleogeographic position of the cratons is corrected (within the confidence levels for the

  20. The Neoproterozoic-Paleozoic Arctic Margins: early stages of geodynamic evolution and plate reconstructions

    Science.gov (United States)

    Vernikovsky, V. A.; Metelkin, D. V.; Vernikovskaya, A. E.; Matushkin, N. Yu.; Lobkovsky, L. I.; Shipilov, E. V.

    2012-04-01

    Available data on the existence of Precambrian metamorphic complexes among the main structures of the Arctic led to the suggestion that a large continental mass existed between Laurentia, Baltica and Siberia - an Arctic continent, more often called Arctida (Zonenshain, Natapov, 1987). It is inferred that as an independent continental mass Arctida was formed after the breakup of Rodinia, and in general it can have a pre-Grenvillian (including Grenvillian) basement age. The breakup of this mass and the collision of its fragments with adjacent cratons led to the formation of heterochronous collisional systems. Arctida probably included the Kara, Novosibirsk, Alaska-Chukotka blocks, the blocks of northern Alaska and the submerged Lomonosov Ridge, small fragments of the Inuit fold belt in the north of Greenland and the Canadian archipelago, the structures of the Svalbard and maybe the Timan-Pechora plates. However the inner structure of this paleocontinent, the mutual configuration of the blocks and its evolution in the Neoproterozoic-Paleozoic is still a matter of discussion. The most accurate way of solving these issues is by using paleomagnetic data, but those are nonexistent for most of the defined blocks. Reliable paleomagnetic determinations for the Neoproterozoic-Paleozoic time interval we are concerned with are available only for fragments of an island arc from Central Taimyr, which are 960 m.y. old (Vernikovsky et al., 2011) and for which the paleomagnetic pole is very close to the pole of Siberia from (Pavlov et al., 2002), and of the Kara microcontinent. This includes three paleomagnetic poles for 500, 450 and 420 Ma (Metelkin et al., 2000; Metelkin et al., 2005). It is those data that made up the basis of the presented paleotectonic reconstructions along with an extensive paleomagnetic database for the cratons of Laurentia, Baltica, Siberia and Gondwana. The paleogeographic position of the cratons is corrected (within the confidence levels for the

  1. Origin and evolution of marginal basins of the NW Pacific: Diffuse-plate tectonic reconstructions

    CERN Document Server

    Xu, Junyuan; Ben-Avraham, Zvi; Yu, Ho-Shing

    2012-01-01

    Formation of the gigantic linked dextral pull-apart basin system in the NW Pacific is due to NNE- to ENE-ward motion of east Eurasia. This mainly was a response to the Indo-Asia collision which started about 50 Ma ago. The displacement of east Eurasia can be estimated using three aspects: (1) the magnitude of pull-apart of the dextral pull-apart basin system, (2) paleomagnetic data from eastern Eurasia and the region around the Arctic, and (3) the shortening deficits in the Large Tibetan Plateau. All the three aspects indicate that there was a large amount (about 1200 km) of northward motion of the South China block and compatible movements of other blocks in eastern Eurasia during the rifting period of the basin system. Such large motion of the eastern Eurasia region contradicts any traditional rigid plate tectonic reconstruction, but agrees with the more recent concepts of non-rigidity of both continental and oceanic lithosphere over geological times. Based on these estimates, the method developed for resto...

  2. Early Tertiary plate reconstructions for the South China Sea region: constraints from northwest Borneo

    Science.gov (United States)

    Gower, Robert J. W.

    Previous plate reconstructions and tectonic syntheses for the southeast Asia region (Leichti et al. 1960, Ben Avraham and Uyeda 1973, Hamilton 1979, Holloway 1982, Taylor and Hayes 1982) have all highlighted the problems of correlating events in northwest Borneo with contemporaneous extension of the South China Sea. Theoretical modelling of crustal scale deformation in Asia during the Tertiary (Tapponnier et al. 1982) following India's collision with Asia suggested that the opening of the South China Sea basin accommodated major sinistral displacement. Haile (1973) and Hamilton (1979) have proposed that active subduction of oceanic crust beneath northwestern Borneo during the late Cretaceous and early Tertiary was associated with the development of a major arcuate accretionary complex, the "Crocker-Rajang" complex (Haile 1973), which is exposed over a large area of West Malaysia. Contemporaneous outer arc basin sedimentation in west Sarawak and eastern Kalimantan is consistent with a southeasterly dipping orientation of subduction at the margin. The duration of subduction is poorly constrained, but the initiation of major clastic depocenter in the Baram-Belait area during the early Miocene (Brondjik 1963), indicates a major change in sedimentation and deformational style at the northwestern Bornea continental margin. Pre-Miocene geological and paleomagnetic evidence from Borneo is inconsistent with the simple model of estrusion tectonics and suggests that Borneo and Malaya were separate microplates during the early Tertiary.

  3. A reconstructed edge-based smoothed DSG element based on global coordinates for analysis of Reissner-Mindlin plates

    Science.gov (United States)

    Yang, Gang; Hu, De'an; Long, Shuyao

    2017-02-01

    A reconstructed edge-based smoothed triangular element, which is incorporated with the discrete shear gap (DSG) method, is formulated based on the global coordinate for analysis of Reissner-Mindlin plates. A symbolic integration combined with the smoothing technique is implemented to calculate the smoothed finite element matrices, which is integrated along the boundaries of each smoothing cell. Numerical results show that the proposed element is free from shear locking, and its results are in good agreement with the exact solutions, even for very thin plates with extremely distorted elements. The proposed element gives more accurate results than the original DSG element without smoothing, and it can be taken as an alternative element for analysis of Reissner-Mindlin plates. The prominent feature of the present element is that the integration scheme is unified in the smoothed form for all of the finite element matrices.

  4. Philippine Sea and East Asian plate tectonics since 52 Ma constrained by new subducted slab reconstruction methods

    Science.gov (United States)

    Wu, Jonny; Suppe, John; Lu, Renqi; Kanda, Ravi

    2016-06-01

    We reconstructed Philippine Sea and East Asian plate tectonics since 52 Ma from 28 slabs mapped in 3-D from global tomography, with a subducted area of ~25% of present-day global oceanic lithosphere. Slab constraints include subducted parts of existing Pacific, Indian, and Philippine Sea oceans, plus wholly subducted proto-South China Sea and newly discovered "East Asian Sea." Mapped slabs were unfolded and restored to the Earth surface using three methodologies and input to globally consistent plate reconstructions. Important constraints include the following: (1) the Ryukyu slab is ~1000 km N-S, too short to account for ~20° Philippine Sea northward motion from paleolatitudes; (2) the Marianas-Pacific subduction zone was at its present location (±200 km) since 48 ± 10 Ma based on a >1000 km deep slab wall; (3) the 8000 × 2500 km East Asian Sea existed between the Pacific and Indian Oceans at 52 Ma based on lower mantle flat slabs; (4) the Caroline back-arc basin moved with the Pacific, based on the overlapping, coeval Caroline hot spot track. These new constraints allow two classes of Philippine Sea plate models, which we compared to paleomagnetic and geologic data. Our preferred model involves Philippine Sea nucleation above the Manus plume (0°/150°E) near the Pacific-East Asian Sea plate boundary. Large Philippine Sea westward motion and post-40 Ma maximum 80° clockwise rotation accompanied late Eocene-Oligocene collision with the Caroline/Pacific plate. The Philippine Sea moved northward post-25 Ma over the northern East Asian Sea, forming a northern Philippine Sea arc that collided with the SW Japan-Ryukyu margin in the Miocene (~20-14 Ma).

  5. Towards community-driven paleogeographic reconstructions: integrating open-access paleogeographic and paleobiology data with plate tectonics

    Directory of Open Access Journals (Sweden)

    N. Wright

    2013-03-01

    Full Text Available A variety of paleogeographic reconstructions have been published, with applications ranging from paleoclimate, ocean circulation and faunal radiation models to resource exploration; yet their uncertainties remain difficult to assess as they are generally presented as low-resolution static maps. We present a methodology for ground-truthing the digital Palaeogeographic Atlas of Australia by linking the GPlates plate reconstruction tool to the global Paleobiology Database and a Phanerozoic plate motion model. We develop a spatio-temporal data mining workflow to validate the Phanerozoic Palaeogeographic Atlas of Australia with paleoenvironments derived from fossil data. While there is general agreement between fossil data and the paleogeographic model, the methodology highlights key inconsistencies. The Early Devonian paleogeographic model of southeastern Australia insufficiently describes the Emsian inundation that may be refined using biofacies distributions. Additionally, the paleogeographic model and fossil data can be used to strengthen numerical models, such as the dynamic topography and the associated inundation of eastern Australia during the Cretaceous. Although paleobiology data provide constraints only for paleoenvironments with high preservation potential of organisms, our approach enables the use of additional proxy data to generate improved paleogeographic reconstructions.

  6. PLATE

    DEFF Research Database (Denmark)

    Kling, Joyce; Hjulmand, Lise-Lotte

    2008-01-01

    ’s level of English is sufficient for the increasing number of courses offered in English each semester. This paper addresses these concerns and describes a pilot project initiated in 2003 at CBS to gauge the overall English language proficiency of those teaching content courses in English. Through......Copenhagen Business School (CBS) finds itself needing to address the issue of English-medium instruction for its increasing number of foreign exchange and full degree students. With internationalisation as a main pillar of the institution’s agenda, there are concerns whether the teaching faculty...... the Project in Language Assessment for Teaching in English (PLATE) language professionals from CBS’s Language Center observe teachers and provide feedback using evaluation criteria from the Common European Framework for Reference (CEFR) supplemented by some additional criteria which take the LSP nature...

  7. PLATE

    DEFF Research Database (Denmark)

    Kling, Joyce; Hjulmand, Lise-Lotte

    2008-01-01

    Copenhagen Business School (CBS) finds itself needing to address the issue of English-medium instruction for its increasing number of foreign exchange and full degree students. With internationalisation as a main pillar of the institution’s agenda, there are concerns whether the teaching faculty......’s level of English is sufficient for the increasing number of courses offered in English each semester. This paper addresses these concerns and describes a pilot project initiated in 2003 at CBS to gauge the overall English language proficiency of those teaching content courses in English. Through...... the Project in Language Assessment for Teaching in English (PLATE) language professionals from CBS’s Language Center observe teachers and provide feedback using evaluation criteria from the Common European Framework for Reference (CEFR) supplemented by some additional criteria which take the LSP nature...

  8. Hook plate fixation for acute acromioclavicular dislocations without coracoclavicular ligament reconstruction: a functional outcome study in military personnel.

    Science.gov (United States)

    Kumar, Narinder; Sharma, Vyom

    2015-08-01

    The aim of our study was to evaluate the shoulder function after clavicular hook plate fixation of acute acromioclavicular dislocations (Rockwood type III) in a population group consisting exclusively of high-demand military personnel. This prospective study was carried out at a tertiary care military orthopaedic centre during 2012-2013 using clavicular hook plate for management of acromioclavicular injuries without coracoclavicular ligament reconstruction in 33 patients. All patients underwent routine implant removal after 16 weeks. The functional outcome was assessed at 3, 6 and 12 months after hook plate removal and 2 years from the initial surgery using the Constant Murley and UCLA Scores. All the patients were male serving soldiers and had sustained acromioclavicular joint dislocation (Rockwood type III). Mean age of the patient group was 34.24 years (21-55 years). The mean follow-up period in this study was 23.5 months (20-26 months) after hook plate fixation and an average of 19.9 months (17-22 months) after hook plate removal. The average Constant Score at 3 months after hook plate removal was 60.3 as compared to 83.7 and 90.3 at 6 months and 1 year, respectively, and an average of 91.8 at the last follow-up that was approximately 2 years after initial surgery which was statistically significant (p value acromioclavicular dislocations producing excellent medium-term functional results in high-demand soldiers.

  9. Surgical treatment of acute acromioclavicular joint dislocations: hook plate versus minimally invasive reconstruction.

    Science.gov (United States)

    Metzlaff, S; Rosslenbroich, S; Forkel, P H; Schliemann, B; Arshad, H; Raschke, M; Petersen, W

    2016-06-01

    This study was performed to compare the clinical results of a minimally invasive technique for acute acromioclavicular (AC) joint dislocation repair with the traditional hook plate fixation. Forty-four patients with an acute (within 2 weeks after trauma) complete AC joint separation (35 male, nine female; median age 36.2 years, range 18-56) underwent surgical repair with either a minimally invasive AC joint repair or a conventional hook plate. Functional outcome was evaluated using the Constant-Murley Score (CMS), the TAFT score and the AC joint instability score (ACJI). Radiographic evaluation was performed with bilateral anterior-posterior (a.p.) stress and Alexander views. All patients were available after a median follow-up of 32 months (range 24-51). There were no significant differences in the mean CMS, Taft score and the ACJI between the two groups. The radiological assessment revealed no significant difference in the coracoclavicular distance. In both groups, a slight loss of reduction was observed. Periarticular ossification was seen in 11 patients of the minimally invasive AC joint repair and eight patients of the hook plate group but this did not affect the final outcome. Hook plates were removed after a median interval of 11.9 weeks (range 10-13). Good clinical results can be achieved with both minimally invasive AC joint repair and hook plate fixation. However, in the hook plate group a second operation is mandatory for plate removal. III.

  10. Evaluation of the Biodegradable Plates (PG910/PDO) for Reconstruction of Various Sizes of Orbital Floor Defects in the Blow-Out Fractures.

    Science.gov (United States)

    Tabrizi, Reza; Langner, Nicole J; Pouzesh, Ayatollah; Arabion, Hamidreza

    2013-09-01

    The aim of our study was to evaluate the biodegradable plates (PG910/PDO) for reconstruction of various sizes of the orbital floor defects in the blow-out fractures. We included patients who had an impure blow-out fracture. All patients had a recent trauma and also the surgical intervention was done between 1 and 10 days after trauma. The amount of the orbital floor defect was measured in each case through computed tomography scan. In the surgical intervention, a biodegradable plate was used for the reconstruction of the orbital floor defect along with titanium miniplates used for bone fixation in orbital rim. Due to aesthetic reasons, all patients underwent secondary surgery including removal of titanium miniplates after 18 months. The orbital floor was reevaluated during the removal of the miniplates. The clinical evaluation of remnant defects and biodegradable plates (presence of complete or partial resorption) were documented for each patient. In our study a total of 15 patients (10 males and 5 females) underwent the orbital floor reconstruction using biodegradable miniplates. The size of the orbital floor defects was meanly 3.51 ± 1.29 cm(2). Results demonstrated that 4 out of 15 patients had a remnant defect after resorption of the biodegradable plate. In 10 out of 15 patients, the biodegradable plates completely replaced with fibrous tissues after 18 months. Remaining five patients had partial resorption of plates. There was not any relationship between the defect size and the remnant defects (p > 0.05). A significant relationship was seen between the defect size and the plates' resorption rate (p biodegradable plates is an appropriate option for reconstruction of the orbital floor defects. The defect size does not have any effect on the stability of the plate. However, incomplete plate resorption increases the risk of remnant defects in the orbital floor. The larger defects lead to slow degradation of biodegradable plates.

  11. The efficacy and complications of 2-hole 3.5 mm reconstruction plates and 4 mm noncanulated cancellous screws for temporary hemiepiphysiodesis around the knee.

    Science.gov (United States)

    Aslani, Hossein; Panjavy, Behnam; Bashy, Ramin H Z; Tabrizi, Ali; Nazari, Behrooz

    2014-06-01

    Persistent angular deformities around the knee can lead to growth-plate damage in childhood and osteoarthritis in adulthood. The treatment options include osteotomy and hemiepiphysiodesis. Tension-band plate hemiepiphysiodesis with 8-plate is an effective way to correct these deformities. However, its high cost makes it less available in many countries. In the present series, we have used 3.5 mm reconstruction plates for tension-band temporary hemiepiphysiodesis. Twenty-one patients with bilateral angular deformities of the knee (42 extremities) underwent temporary hemiepiphysiodesis with 3.5 mm reconstruction plates. The diagnosis, BMI, weight, amount of correction of the deformity age, and device failure were analyzed. The mean follow-up period after plate removal was 17 months (ranging from 8 to 24 mo). The mean age of the patients was 10 years and 3 months (± 2 y and 10 mo). Complete correction of the deformities was achieved in 86% of patients. Of the 58 plate and screw constructs, 10% had screw breakage. Patients with genu valgum had 2 screw failures (6.25%), but in the genu varum group there were 4 screw failures (40%). Of the 3 patients who did not have complete correction of the deformities, 2 had mucopolysaccharidosis and 1 was nearing skeletal maturity (16 y old). The age of the patient, body weight, BMI, and degrees of angulation did not have any statistically significant correlation with the screw failure. Screw failures in female patients were more common than in male patients. All implant failures occurred in idiopathic patients. The efficacy of 3.5 mm reconstruction plates for temporary hemiepiphysiodesis around the knee is similar to that of 8-plates. However, the reconstruction plates have a lower cost and are easily available. Noncanulated 3.5 or 4.5 mm cortical screws seem to be superior to 4 mm noncanulated cancellous screws. Level 3.

  12. Hyperspectral image reconstruction using RGB color for foodborne pathogen detection on agar plates

    Science.gov (United States)

    Yoon, Seung-Chul; Shin, Tae-Sung; Park, Bosoon; Lawrence, Kurt C.; Heitschmidt, Gerald W.

    2014-03-01

    This paper reports the latest development of a color vision technique for detecting colonies of foodborne pathogens grown on agar plates with a hyperspectral image classification model that was developed using full hyperspectral data. The hyperspectral classification model depended on reflectance spectra measured in the visible and near-infrared spectral range from 400 and 1,000 nm (473 narrow spectral bands). Multivariate regression methods were used to estimate and predict hyperspectral data from RGB color values. The six representative non-O157 Shiga-toxin producing Eschetichia coli (STEC) serogroups (O26, O45, O103, O111, O121, and O145) were grown on Rainbow agar plates. A line-scan pushbroom hyperspectral image sensor was used to scan 36 agar plates grown with pure STEC colonies at each plate. The 36 hyperspectral images of the agar plates were divided in half to create training and test sets. The mean Rsquared value for hyperspectral image estimation was about 0.98 in the spectral range between 400 and 700 nm for linear, quadratic and cubic polynomial regression models and the detection accuracy of the hyperspectral image classification model with the principal component analysis and k-nearest neighbors for the test set was up to 92% (99% with the original hyperspectral images). Thus, the results of the study suggested that color-based detection may be viable as a multispectral imaging solution without much loss of prediction accuracy compared to hyperspectral imaging.

  13. Application of anterior decompression and reconstruction using titanium mesh with locking plates in the management of cervical spondylotic myelopathy

    Institute of Scientific and Technical Information of China (English)

    Maolin He; Zengming Xiao; Shide Li; Qianfen Chen

    2008-01-01

    Objective:To observe the clinical effect of anterior decompression and reconstruction using titanium mesh with locking plates in the treatment of cervical spondylotic myelopathy.Methods:One hundred and twenty patients with cervical spondylotic myelopathy were treated by anterior decompression and reconstruction using titanium mesh with locking plates.There were 66 men and 54 women ranges in age from 37 to 72 Years(mean age, 58.3 years).The mean Japanese orthopedic surgery association(JOA) scale was 9.6 points before operation.Patients were followed up clinically and radiographically.Results:Having stood surgery well, the operation time ranged between 60-100 min and bleeding during operation ranged between 20-200 ml.There were no case of postoperative infection, recurrent laryngeal nerve palsy, or esophageal or tracheal laceration or rupture.The average follow-up period was 14.3 months(range, 12 to 24 months) in 96 who were followed up.At the last follow-up visit the mean JOA scale had improved to 14.4 points, reflecting an improve ment of 4.8 points.The results were considered to be excellent in 87 patients, good in 25, fair in 6, and poor in 2.No hardware-related complications or adjacent segment degenerative changes were encountered during the follow-up periods.Stable bone union was observed in all cases and the average time required for fusion was 5.7 months.Conclusion:Titanium mesh filled with autologous bone graft can avoid the complications associated with harvesting bone from the iliac crest donor site.When combined with cervical anterior locking plate, it can obtain satisfatory clinical results for the treatment of cervical spondylotic myelopathy.

  14. Seismic tomographic constraints on plate-tectonic reconstruction of Nazca subduction under South America since late Cretaceous (~80 Ma)

    Science.gov (United States)

    Chen, Yi-Wei; Wu, Jonny; Suppe, John; Liu, Han-Fang

    2016-04-01

    Our understanding of the global plate tectonics is based mainly on seafloor spreading and hotspot data obtained from the present earth surface, which records the growth of present ocean basins. However, in convergent tectonic settings vast amounts of lithosphere has been lost to subduction, contributing to increasing uncertainty in plate reconstruction with age. However, subducted lithosphere imaged in seismic tomography provides important information. By analyzing subducted slabs we identify the loci of subduction and assess the size and shape of subducted slabs, giving better constrained global plate tectonic models. The Andean margin of South America is a classic example of continuous subduction up to the present day, providing an opportunity to test the global plate prediction that ~24×10e6 km2 (4.7% of earth surface) lithosphere has been subducted since ~80 Ma. In this study, we used 10 different global seismic tomographies and Benioff zone seismicity under South America. To identify slabs, we first compared all data sets in horizontal slices and found the subducted Nazca slab is the most obvious structure between the surface and 750 km depth, well imaged between 10°N and 30°S. The bottom of the subducted Nazca slab reaches its greatest depth at 1400 km at 3°N (Carnegie Andes) and gradually shallows towards the south with 900 km minimum depth at 30°S (Pampean Andes). To assess the undeformed length of subducted slab, we used a refined cross-sectional area unfolding method from Wu et al. (in prep.) in the MITP08 seismic tomography (Li et al., 2008). Having cut spherical-Earth tomographic profiles that parallel to the Nazca-South America convergence direction, we measured slab areas as a function of depth based on edges defined by steep velocity gradients, calculating the raw length of the slab by the area and dividing an assumed initial thickness of oceanic lithosphere of 100km. Slab areas were corrected for density based on the PREM Earth model

  15. Fabrication of RF Circuit Structures on a PCB Material Using Inkjet Printing-Electroless Plating and the Substrate Preparation Therefor

    NARCIS (Netherlands)

    Sridhar, A.; Perik, M.A.; Reiding, J.; Dijk, van D.J.; Akkerman, R.

    2009-01-01

    This paper describes the optimisation of the surface characteristics of a high-frequency substrate material widely used in the PCB (printed circuit board) industry by means of CF4/O2 plasma etching, in order to make it suitable for the fabrication of RF (radio frequency) circuit structures by a comb

  16. Object-wave reconstruction by carbon film-based Zernike- and Hilbert-phase plate microscopy: A theoretical study not restricted to weak-phase objects

    Energy Technology Data Exchange (ETDEWEB)

    Dries, M., E-mail: manuel.dries@kit.edu [Laboratorium fuer Elektronenmikroskopie, Karlsruher Institut fuer Technologie (KIT), D-76128 Karlsruhe (Germany); Schultheiss, K.; Gamm, B. [Laboratorium fuer Elektronenmikroskopie, Karlsruher Institut fuer Technologie (KIT), D-76128 Karlsruhe (Germany); Rosenauer, A. [Institut fuer Festkoerperphysik, Universitaet Bremen, D-28359 Bremen (Germany); Schroeder, R.R. [BioQuant CellNetworks, Universitaet Heidelberg, D-69120 Heidelberg (Germany); Gerthsen, D. [Laboratorium fuer Elektronenmikroskopie, Karlsruher Institut fuer Technologie (KIT), D-76128 Karlsruhe (Germany)

    2011-01-15

    Transmission electron microscopy phase-contrast images taken by amorphous carbon film-based phase plates are affected by the scattering of electrons within the carbon film causing a modification of the image-wave function. Moreover, image artefacts are produced by non-centrosymmetric phase plate designs such as the Hilbert-phase plate. Various methods are presented to correct phase-contrast images with respect to the scattering of electrons and image artefacts induced by phase plates. The proposed techniques are not restricted to weak-phase objects and linear image formation. Phase-contrast images corrected by the presented methods correspond to those taken by an ideal centrosymmetric, matter-free phase plate and are suitable for object-wave reconstruction. -- Research Highlights: {yields} Object-wave reconstruction by phase plates considering nonlinear image formation. {yields} Requirement of three (five) images in case of Zernike- (Hilbert-) phase plates. {yields} Analytical correction of damping and/or image artefacts induced by phase plates.{yields} Validation by simulation of crystalline silicon.

  17. JaMBES: A "New" Way of Calculating Plate Tectonic Reconstruction

    Science.gov (United States)

    Chambord, A. I.; Smith, E. G. C.; Sutherland, R.

    2014-12-01

    Calculating the paleoposition of tectonic plates using marine geophysical data has been usually done by using the Hellinger criterion [Hellinger, 1981]. However, for the Hellinger software [Kirkwood et al., 1999] to produce stable results, we find that the input data must be abundant and spatially well distributed. Although magnetic anomalies and fracture zone data have been increasingly abundant since the 1960s, some parts of the globe remain too sparsely explored to provide enough data for the Hellinger code to provide satisfactory rotations. In this poster, we present new software to calculate the paleopositions of tectonic plates using magnetic anomalies and fracture zone data. Our method is based on the theory of plate tectonics as introduced by [Bullard et al., 1965] and [Morgan, 1968], which states that ridge segments (ie. magnetic lineations) and fracture zones are at right angles to each other. In order to test our software, we apply it to a region of the world where climatic conditions hinder the acquisition of magnetic data: the Southwest Pacific, between New Zealand and Antarctica from breakup time to chron 20 (c43Ma). Bullard, E., J. E. Everett, and A. G. Smith (1965), The fit of continents around the atlantic, Philosophical Transactions of the Royal Society of London, Series A: Mathematical and Physical Sciences, 258(1088), 41-51. Hellinger, S. J. (1981), The uncertainties of finite rotations in plate tectonics, Journal of Geophysical Research, 86(B10), 9312-9318. Kirkwood, B. H., J. Y. Royer, T. C. Chang, and R. G. Gordon (1999), Statistical tools for estimating and combining finite rotations and their uncertainties, Geophysical Journal International, 137(2), 408-428. Morgan, W. J. (1968), Rises, trenches, great faults, and crustal blocks, Journal of Geophysical Research, 73(6), 1959-1982.

  18. Acromioclavicular joint reconstruction by coracoid process transfer augmented with hook plate.

    Science.gov (United States)

    Wang, Yeming; Zhang, Jianguo

    2014-06-01

    Various techniques have been reported for the treatment of chronic acromioclavicular (AC) joint separation. The purpose of this study was to evaluate the results of surgical construction of coracoclavicular ligament using coracoid process transfer augmented with a hook plate fixation. Twenty-one patients treated with coracoid process transfer augmented with a hook plate fixation for chronic type III and V AC injuries were retrospectively analysed in 2003-2009. The age of the patients ranged from 23 to 58 years with an average age of 41.6 years. The patients were followed up clinically and radiographically, with an average of 33.0 months. Functional status and the ability to return to work were recorded during follow-up. Constant score and visual analogue scale (VAS) for pain were measured. The mean Constant score has increased from 70.9 points preoperatively to 90.7 points at follow-up. The mean VAS score has decreased from 4.7 preoperatively to 1.2 at follow-up. The average abduction was 172°, forward flexion was 170° and external rotation was 56°. There were 10 excellent results, 10 good results and one fair result. All patients had resumed their job or returned to original sport activity at mean 3.7 months postoperatively. No reduction loss was observed after plate removal and the final follow-up. Despite retrospective nature of the study, the outcomes of surgical construction with process transfer augmented with hook plate fixation are promising for chronic type III and V AC injuries. Therapeutic level IV. Retrospective case series, treatment study. Copyright © 2014 Elsevier Ltd. All rights reserved.

  19. Reconstruction of the mandible using preshaped 2.3 mm titanium plates, autogenous particulate cortico-cancellous bone grafts and platelet rich plasma: a report on eight patients.

    NARCIS (Netherlands)

    Merkx, M.A.W.; Fennis, J.P.M.; Verhagen, C.M.; Stoelinga, P.J.W.

    2004-01-01

    The results are presented of eight patients who had partial mandibulectomies for malignant tumours and were secondarily reconstructed with pre-shaped 2.3 mm titanium plates, autogenous particulate cortico-cancellous bone grafts and platelet rich plasma. Healing was uneventful in all cases and when p

  20. Inkjet-printing- and electroless-plating- based fabrication of RF circuit structures on high-frequency substrates

    NARCIS (Netherlands)

    Sridhar, A.; Reiding, J.; Adelaar, H.; Achterhoek, F.; Dijk, van D.J.; Akkerman, R.

    2009-01-01

    In this paper, a method to fabricate radio frequency (RF) circuit structures is described. This method involves inkjet printing of a silver nanoparticle-based ink on a functional substrate material to create the seed track (i.e., the seed layer), onto which copper is subsequently deposited by an ele

  1. Plate tectonic reconstruction of South and East Asia since 43 Ma using seismic tomographic constraints: role of the subducted ';East Asia Sea' (Invited)

    Science.gov (United States)

    Wu, J. E.; Suppe, J.; Renqi, L.; Kanda, R. V.

    2013-12-01

    Lithosphere that subducts at convergent plate boundaries provides a potentially decipherable plate tectonic record. In this study we use global seismic tomography to map subducted slabs in the upper and lower mantle under South and East Asia to constrain plate reconstructions. The mapped slabs include the Pacific, the Indian Ocean and Banda Sea, the Molucca Sea, Celebes Sea, the Philippine Sea and Eurasia, New Guinea and other lower mantle detached slabs. The mapped slabs were restored to the earth surface and used with Gplates software to constrain a globally-consistent, fully animated plate reconstruction of South and East Asia. Three principal slab elements dominate possible plate reconstructions: [1] The mapped Pacific slabs near the Izu-Bonin and the Marianas trenches form a subvertical slab curtain or wall extending down to 1500 km in the lower mantle. The ';slab curtain' geometry and restored slabs lengths indicate that the Pacific subduction zone has remained fixed within +/- 250 km of its present position since ~43 Ma. In contrast, the Tonga Pacific slab curtain records at least 1000 km trench rollback associated with expansion of back-arc basins. [2] West of the Pacific slab curtain, a set of flat slabs exist in the lower mantle and record a major 8000km by 2500-3000km ocean that existed at ~43 Ma. This now-subducted ocean, which we call the ';East Asian Sea', existed between the Ryukyu Asian margin and the Lord Howe hotspot, present-day eastern Australia, and fills a major gap in Cenozoic plate reconstructions between Indo-Australia, the Pacific Ocean and Asia. [3] An observed ';picture puzzle' fit between the restored edges of the Philippine Sea, Molucca Sea and Indian Ocean slabs suggests that the Philippine Sea was once part of a larger Indo-Australian Ocean. Previous models of Philippine Sea plate motions are in conflict with the location of the East Asian Sea lithosphere. Using the mapped slab constraints, we propose the following 43 Ma to 0 plate

  2. Start-up circuit upgrading to reduce the erosion of the rotor blades of the last stages of steam turbines and prevent the mass strips of stellite plates

    Science.gov (United States)

    Bozhko, V. V.; Gorin, A. V.; Zaitsev, I. V.; Kovalev, I. A.; Nosovitskii, I. A.; Orlik, V. G.; Lomagin, S. N.; Chernov, V. P.

    2017-03-01

    At turbine starts with low steam flow rates in idle mode, the low-pressure rotor blades consume energy, causing the ventilation heating of the stages and creating higher depression in them than in the condenser. This leads to the return steam flows in the exhaust of the low-pressure cylinder (LPC), reducing the heat due to the moisture of starting steam damps and cooling injections. It is shown that, as a result of upgrading with the transition to fully milled shroud platforms of rotor blades, the depression in the stages decreases and their cooling efficiency is reduced due to the removal of an elastic turn of the rotor blades under the action of centrifugal forces and seal of them by periphery. Heating the rotor blades of the last stages exceeds the temperature threshold of soldering resistance of stellite plates (150°C), and their mass strips begin. The start-up circuit providing both the temperature retention of the last stages lower the soldering resistance threshold due to overwetting the steam damps up to saturation condition and the high degree of removal from the dump steam of excessive erosive-dangerous condensed moisture was proposed, applied, and tested at the operating power unit. The investment in the development and application of the new start-up circuit are compensated in the course of a year owing to guaranteed prevention of the strips of stellite plates that lengthens the service life of the rotor blades of the last stages as well as increase of the rotor blade efficiency due to the sharp decrease of erosive wear of the profiles and reduction of their surface roughness. This reduces the annual consumption of equivalent fuel by approximately 1000 t for every 100 MW of installed capacity.

  3. Orogenesis of the Oman Mountains - a new geodynamic model based on structural geology, plate reconstructions and thermochronology

    Science.gov (United States)

    Grobe, Arne; Virgo, Simon; von Hagke, Christoph; Ralf, Littke; Urai, Janos L.

    2017-04-01

    faults on the northern flank of the anticline. We link these results with the geodynamic framework of the area, constrained by plate tectonic reconstructions. Furthermore, we constrain the exhumation history of the mountain belt using zircon (U-Th-Sm)/He dating. Geodynamic and exhumation events can be linked to structural generations. This results in a new tectonic model of the Oman Mountains. We find a remarkable along-strike consistency of mountain building phases and argue involvement of a micro-plate is not required. Breton, J.P., Béchennec, F., Le Métour, J., Moen-Maurel, L., Razin, P., 2004. Eoalpine (Cretaceous) evolution of the Oman Tethyan continental margin: Insights from a structural field study in Jabal Akhdar (Oman Mountains). GeoArabia 9, 41-58. Fink, R., Virgo, S., Arndt, M., Visser, W., Littke, R., Urai, J.L.L., 2015. Solid bitumen in calcite veins from the Natih Formation in the Oman Mountains: Multiple phases of petroleum migration in a changing stress field. Int. J. Coal Geol. 157, 39-51. doi:10.1016/j.coal.2015.07.012 Grobe, A., Urai, J.L.L., Littke, R., Lünsdorf, N.K.K., 2016. Hydrocarbon generation and migration under a large overthrust: The carbonate platform under the Semail Ophiolite, Jebel Akhdar, Oman. Int. J. Coal Geol. 1-17. doi:10.1016/j.coal.2016.02.007

  4. Deciphering detailed plate kinematics of the Indian Ocean and developing a unified model for East Gondwanaland reconstruction: An Indian-Australian-French initiative

    Digital Repository Service at National Institute of Oceanography (India)

    Yatheesh, V.; Dyment, J.; Bhattacharya, G.C.; Muller, R.D.

    2January 2013 DCS-DST NEWS DECIPHERING DETAILED PLATE KINEMATICS OF THE INDIAN OCEAN AND DEVELOPING A UNIFIED MODEL FOR EAST GONDWANALAND RECONSTRUCTION: AN INDIAN- AUSTRALIAN-FRENCH INITIATIVE V. YATHEESH1, J. DYMENT2, G.C. BHATTACHARYA1, R... was proposed by McKenzie and Sclater (1971, Geophys. J. R. Astron. Soc., v. 25, 437-528) mainly based on widely spaced geophysical data acquired during the International Indian Ocean Expedition (IIOE). Many subsequent studies (see Appendix-1) enriched...

  5. [A case of locally advanced breast cancer successfully treated with wide resection and reconstruction of chest wall with A-O metallic plates].

    Science.gov (United States)

    Imamura, H; Tatsuta, M; Masuda, N; Miya, A; Ezumi, K; Shimizu, J; Ikeda, M; Ishida, H; Masutani, S; Kawasaki, T; Furukawa, H; Satomi, T

    2001-10-01

    A 63-year-old female with locally advanced breast cancer was treated with preoperative chemotherapy using docetaxel. The therapeutic regimen was comprised of four cycles at 3-week intervals. One cycle consisted of 80 mg of docetaxel which was administered on day 1. A remarkable response was confirmed. The side effects such as leukopenia, general fatigue and alopecia were moderate and had no influence on the patient's QOL. After preoperative chemotherapy, a full thickness chest wall resection was performed. Chest wall defect was reconstructed with orthopedic A-O metallic plates, Marlex mesh and rectus abdominis myocutaneous flap. These metal plates were very useful because it was easy to bend and twist them manually to fit the defect at the time of operation. Moreover, the curved metal plates preserved the cone form of the chest cage. The postoperative course was favourable without frail chest or wound infection.

  6. Accuracy of fibular sectioning and insertion into a rapid-prototyped bone plate, for mandibular reconstruction using CAD-CAM technology.

    Science.gov (United States)

    Ciocca, Leonardo; Marchetti, Claudio; Mazzoni, Simona; Baldissara, Paolo; Gatto, Maria Rosaria Antonella; Cipriani, Riccardo; Scotti, Roberto; Tarsitano, Achille

    2015-01-01

    Modern techniques of mandibular reconstruction, such as CAD-CAM technology and rapid prototyping, offer new means by which reconstructive surgery can be planned to optimise aesthetic outcomes and prosthetic rehabilitation. The high degree of accuracy afforded by these approaches is principally attributable to high-precision fibular sectioning and insertion of the bone into a customised bone plate. CAD-CAM mandibular reconstruction procedures using vascularised bone free-flap transfers were performed on 10 patients with benign or malignant neoplasms. Five were not treated with the aid of CAD-CAM technology, and served as the control group. Five were scheduled for maxillofacial surgery using surgical cutting guides and customised bone plates. A generalised linear model for linear measures was used to compare the accuracy of reconstruction between the two groups. A difference, even though not significant, in the lateral shift of the mesial and distal positions of the fibular units was evident between groups. CAD-CAM-generated fibular surgical guides afford improved accuracy when used to restore native anatomy, especially in the context of mandibular arch restoration, and both operating room time and related costs are reduced during fibular sectioning.

  7. Reconstruction

    Directory of Open Access Journals (Sweden)

    Stefano Zurrida

    2011-01-01

    Full Text Available Breast cancer is the most common cancer in women. Primary treatment is surgery, with mastectomy as the main treatment for most of the twentieth century. However, over that time, the extent of the procedure varied, and less extensive mastectomies are employed today compared to those used in the past, as excessively mutilating procedures did not improve survival. Today, many women receive breast-conserving surgery, usually with radiotherapy to the residual breast, instead of mastectomy, as it has been shown to be as effective as mastectomy in early disease. The relatively new skin-sparing mastectomy, often with immediate breast reconstruction, improves aesthetic outcomes and is oncologically safe. Nipple-sparing mastectomy is newer and used increasingly, with better acceptance by patients, and again appears to be oncologically safe. Breast reconstruction is an important adjunct to mastectomy, as it has a positive psychological impact on the patient, contributing to improved quality of life.

  8. Repositioning template for mandibular reconstruction with fibular free flap: an alternative technique to pre-plating and virtual surgical planning

    OpenAIRE

    Berrone, M.; Crosetti, E.; Succo, G

    2014-01-01

    SUMMARY Oral malignancies involving the mandibular bone require a complex reconstructive plan. Mandibular reconstruction with a fibular free flap is currently considered the best choice for functional and aesthetic rehabilitation after oncological surgery. This flap can be modelled with multiple osteotomies and can provide bone, muscle and skin for composite reconstruction. One of the most delicate aspects of mandibular reconstruction is the technique of bone modelling; the risk of prolonging...

  9. High-resolution estimates of Nubia-Somalia plate motion since 20 Ma from reconstructions of the Southwest Indian Ridge, Red Sea, and Gulf of Aden

    Science.gov (United States)

    DeMets, C.; Merkouriev, S.

    2016-07-01

    Large gaps and inconsistencies remain in published estimates of Nubia-Somalia plate motion based on reconstructions of seafloor spreading data around Africa. Herein, we use newly available reconstructions of the Southwest Indian Ridge at ˜1-Myr intervals since 20 Ma to estimate Nubia-Somalia plate motion farther back in time than previously achieved and with an unprecedented degree of temporal resolution. At the northern end of the East African rift, our new estimates of Nubia-Somalia motion for six times from 0.78 Ma to 5.2 Ma differ by only 2% from the rift-normal component of motion that is extrapolated from a recently estimated GPS angular velocity. The rate of rift-normal extension thus appears to have remained steady since at least 5.2 Ma. Our new rotations indicate that the two plates have moved relative to each other since at least 16 Ma and possibly longer. Motion has either been steady since at least 16 Ma or accelerated modestly between 6 and 5.2 Ma. Our Nubia-Somalia rotations predict 42.5±3.8 km of rift-normal extension since 10.6 Ma across the well-studied, northern segment of the Main Ethiopian Rift, consistent with 40-50 km estimates for extension since 10.6 Myr based on seismological surveys of this narrow part of the plate boundary. Nubia-Somalia rotations are also derived by combining newly estimated Somalia-Arabia rotations that reconstruct the post-20-Ma opening of the Gulf of Aden with Nubia-Arabia rotations estimated via a probabilistic analysis of plausible opening scenarios for the Red Sea. These rotations predict Nubia-Somalia motion since 5.2 Myr that is consistent with that determined from Southwest Indian Ridge data and also predict 40±3 km of rift-normal extension since 10.6 Ma across the Main Ethiopian Rift, consistent with our 42.5±3.8 km Southwest Indian Ridge estimate. Our new rotations exclude at high confidence level previous estimates of 12±13 km and 123±14 km for rift-normal extensions across the Main Ethiopian Rift since

  10. High-resolution estimates of Nubia-Somalia plate motion since 20 Ma from reconstructions of the Southwest Indian Ridge, Red Sea and Gulf of Aden

    Science.gov (United States)

    DeMets, C.; Merkouriev, S.

    2016-10-01

    Large gaps and inconsistencies remain in published estimates of Nubia-Somalia plate motion based on reconstructions of seafloor spreading data around Africa. Herein, we use newly available reconstructions of the Southwest Indian Ridge at ˜1-Myr intervals since 20 Ma to estimate Nubia-Somalia plate motion farther back in time than previously achieved and with an unprecedented degree of temporal resolution. At the northern end of the East African rift, our new estimates of Nubia-Somalia motion for six times from 0.78 Ma to 5.2 Ma differ by only 2 per cent from the rift-normal component of motion that is extrapolated from a recently estimated GPS angular velocity. The rate of rift-normal extension thus appears to have remained steady since at least 5.2 Ma. Our new rotations indicate that the two plates have moved relative to each other since at least 16 Ma and possibly longer. Motion has either been steady since at least 16 Ma or accelerated modestly between 6 and 5.2 Ma. Our Nubia-Somalia rotations predict 42.5 ± 3.8 km of rift-normal extension since 10.6 Ma across the well-studied, northern segment of the Main Ethiopian Rift, consistent with 40-50 km estimates for extension since 10.6 Myr based on seismological surveys of this narrow part of the plate boundary. Nubia-Somalia rotations are also derived by combining newly estimated Somalia-Arabia rotations that reconstruct the post-20-Ma opening of the Gulf of Aden with Nubia-Arabia rotations estimated via a probabilistic analysis of plausible opening scenarios for the Red Sea. These rotations predict Nubia-Somalia motion since 5.2 Myr that is consistent with that determined from Southwest Indian Ridge data and also predict 40 ± 3 km of rift-normal extension since 10.6 Ma across the Main Ethiopian Rift, consistent with our 42.5 ± 3.8 km Southwest Indian Ridge estimate. Our new rotations exclude at high confidence level previous estimates of 12 ± 13 and 123 ± 14 km for rift-normal extensions across the Main

  11. Implementation of an Electronic Circuit for SSSA Control Approach of a Plate Type Element and Experimental Match with a Feed-Forward Approach

    Directory of Open Access Journals (Sweden)

    Viscardi Massimo

    2016-12-01

    Full Text Available Successful implementation of an active vibration control system is strictly correlated to the exact knowledge of the dynamic behavior of the system, of the excitation level and spectra and of the sensor and actuator’s specification. Only the correct management of these aspects may guarantee the correct choice of the control strategy and the relative performance. Within this paper, some preliminary activities aimed at the creation of a structurally simple, cheap and easily replaceable active control systems for metal panels are discussed. The final future aim is to control and to reduce noise, produced by vibrations of metal panels of the body of a car. The paper is focused on two points. The first one is the realization of an electronic circuit for Synchronized Shunted Switch Architecture (SSSA with the right dimensioning of the components to control the proposed test article, represented by a rectangular aluminum plate. The second one is a preliminary experimental study on the test article, in controlled laboratory conditions, to compare performances of two possible control approach: SSSA and a feed-forward control approach. This comparison would contribute to the future choice of the most suitable control architecture for the specific attenuation of structure-born noise related to an automotive floor structure under deterministic (engine and road-tyre interaction and stochastic (road-tyre interaction and aerodynamic forcing actions.

  12. Submental Artery Island Flap in Reconstruction of Harde Plate after wide Surgical Resection of Veruccous Carcinoma. Two case reports

    Directory of Open Access Journals (Sweden)

    Amin Rahpeyma

    2013-06-01

    Full Text Available Introduction: Reconstruction of intraoral soft tissue defects is important in restoring function and esthetic. In large defects, there will be demand for regional pedicle flaps or free flaps. Hard palate separates nasal and oral cavities. Due to the small surface area between flap and remaining palate after surgical resections, optimal blood supply of the flaps for hard palate reconstructions are needed. This article demonstrates immediate reconstruction of two edentulous hemimaxillectomy patients with submental artery Island flap and brief review of this flap discussed. 

  13. Repositioning template for mandibular reconstruction with fibular free flaps: an alternative technique to pre-plating and virtual surgical planning.

    Science.gov (United States)

    Berrone, M; Crosetti, E; Succo, G

    2014-08-01

    Oral malignancies involving the mandibular bone require a complex reconstructive plan. Mandibular reconstruction with a fibular free flap is currently considered the best choice for functional and aesthetic rehabilitation after oncological surgery. This flap can be modelled with multiple osteotomies and can provide bone, muscle and skin for composite reconstruction. One of the most delicate aspects of mandibular reconstruction is the technique of bone modelling; the risk of prolonging the period of ischaemia and not restoring the correct maxillomandibular and occlusal relationships can ultimately lead to a higher rate of complications as well as poor aesthetic and functional results. Recently, there has been rising interest in virtual surgical planning and computer-assisted mandibular reconstruction in pre-operative planning; however, this is not always possible because of the costs involved and the set-up time for the entire procedure. In this paper, we present a simple and inexpensive technique for fibular free flap modelling and repositioning after segmental resection of the mandible; the technique entails the pre-operative preparation of a resin repositioning template on a stereolithographic model. This technique has been successfully applied in four cases: two cases underwent resection involving only the mandibular body, one case involving the mandibular body and symphysis and one case in which a ramus to ramus resection was performed. In this preliminary report, we show that the resin repositioning template is an easy, safe and useful tool for mandibular reconstruction with a fibular free flap.

  14. [EFFECTIVENESS OF CLAVICULAR HOOK PLATE COMBINED WITH TRAPEZIUS MUSCLE FASCIA FOR RECONSTRUCTION OF ACROMIOCLAVICULAR AND CORACOCLAVICULAR LIGAMENTS TO TREAT COMPLETE ACROMIOCLAVICULAR JOINT DISLOCATION].

    Science.gov (United States)

    Wang, Chaoliang; Wang, Yingzhen; Zhu, Tao; Sun, Xuesheng; Lin, Chu; Gao, Bo; Li, Xinxia

    2015-02-01

    To explore the effectiveness of the clavicular hook plate combined with trapezius muscle fascia for reconstruction of acromioclavicular and coracoclavicular ligaments to treat acute complete acromioclavicular dislocations. Between January 2008 and April 2012, 66 patients with acromioclavicular dislocation were treated with the clavicular hook plate combined with trapezius muscle fascia for reconstruction of acromioclavicular and coracoclavicular ligaments in 32 cases (experimental group) and with the clavicular hook plate in 34 cases (control group). There was no significant difference in gender, age, injured side, the cause of injury, and the time from injury to operation between 2 groups (P > 0.05). Visual analogue scale (VAS), Constant shoulder scores, and coracoid clavi-cledistance (CC. Dist) were measured at preoperation and at 2 years after operation. Signal/noise quotiem (SNQ) was measured by MRI at 2 years after operation. The operation complications were observed. The patients of 2 groups obtained primary healing of incision. The morbidity of complication in experimental group (12.5%, 4/32) was significantly lower than that in control group (91.2%, 31/34) (Χ2 = 40.96, P = 0.00). All the cases were followed up 2.8 years on average (range, 2 to 4 years). VAS scores and CC.Dist significantly decreased at 2 years after operation when compared with preoperative values in the 2 groups (P acromioclavicular and coracoclavicular ligaments is successful in treating acute complete acromioclavicular dislocations, with the advantages of higher ligament healing, less complication, and early improvement of shoulder functions.

  15. Reconstruction of Full-Field Wall Pressure Fluctuations on a Flat Plate in the Wake of a Step Cylinder: Applications of Linear Stochastic Estimation (LSE)

    Science.gov (United States)

    Peng, Di; Chen, Yujia; Wang, Shaofei; Liu, Yingzheng; Wang, Weizhe

    2016-11-01

    Previous studies have shown that it is possible to reconstruct the full flow field based on time-resolved measurements at discrete locations using linear stochastic estimation (LSE). The objective of this study is to develop and apply this technique to wall pressure fluctuation measurements in low speed flows. Time-resolved wall pressure fluctuations on a flat plate in the wake of a step cylinder at low speed (V PSP). The microphone arrays are arranged properly to capture the dominant features in the flow field at 10 kHz. The PSP is excited using a continuous UV-LED, and the luminescent signal is recorded by a high-speed camera at 2 kHz. The microphone data at discrete locations are used to reconstruct the full-field wall pressure fluctuations based on LSE. The PSP results serve as basis for improvement of the LSE scheme and also for validation of the reconstructed pressure field. Other data processing techniques including proper orthogonal decomposition (POD) and dynamic mode decomposition (DMD) are also used for analyzing the unsteady flow features. This LSE technique has great potential in real-time flow diagnostics and control.

  16. The effect orientation of features in reconstructed atom probe data on the resolution and measured composition of T1 plates in an A2198 aluminium alloy.

    Science.gov (United States)

    Mullin, Maria A; Araullo-Peters, Vicente J; Gault, Baptiste; Cairney, Julie M

    2015-12-01

    Artefacts in atom probe tomography can impact the compositional analysis of microstructure in atom probe studies. To determine the integrity of information obtained, it is essential to understand how the positioning of features influences compositional analysis. By investigating the influence of feature orientation within atom probe data on measured composition in microstructural features within an AA2198 Al alloy, this study shows differences in the composition of T1 (Al2CuLi) plates that indicates imperfections in atom probe reconstructions. The data fits a model of an exponentially-modified Gaussian that scales with the difference in evaporation field between solutes and matrix. This information provides a guide for obtaining the most accurate information possible.

  17. Study of Cyanide-free Electroless Gold Plating for Patterned Circuits with Fine-pitch%细间距图形电路无氰化学镀金工艺研究*

    Institute of Scientific and Technical Information of China (English)

    刘东光; 胡江华

    2013-01-01

    Commercial cyanide-free electroless Gold Plating technology used to deposit gold film on patterned circuits with fine-pitch(50 µm/50 µm). Investigated results indicated the thickness of gold film up to 2 µm, the film surface is smooth, and no gold coating spill over. New electroless gold plating progress as one of the weld surface treatment technology, can be used to selective area plating, has contact conductive, good bonding performance, and can compatible with various solder. This technology has the significance for the fine-pitch patterned circuits.%  采用市售无氰化学金工艺在线宽/间距(50µm/50µm)精细图形电路表面化学镀金。镀层表面均匀一致,厚度可达2µm以上,无镀金层溢出现象。新的化学镀金工艺作为微带板可焊性表面处理技术之一,兼具可选择区域镀、可接触导通、良好的键合性能,能兼容各种助焊剂,对于细间距图形电路表面处理具有十分重要的意义。

  18. Acoustic Emission tomography based on simultaneous algebraic reconstruction technique to visualize the damage source location in Q235B steel plate

    Science.gov (United States)

    Jiang, Yu; Xu, Feiyun; Xu, Bingsheng

    2015-12-01

    Acoustic Emission (AE) tomography based on Simultaneous Algebraic Reconstruction Technique (SART), which combines the traditional location algorithm with the SART algorithm by using AE events as its signal sources, is a new visualization method for inspecting and locating the internal damages in the structure. In this paper, the proposed method is applied to examine and visualize two man-made damage source locations in the Q235B steel plate to validate its effectiveness. Firstly, the Q235B steel plate with two holes specimen is fabricated and the pencil lead break (PLB) signal is taken as the exciting source for AE tomography.Secondly, A 6-step description of the SART algorithm is provided and the three dimensional(3D)image contained the damage source locations is visualized by using the proposed algorithm in terms of a locally varying wave velocity distribution. It is shown that the AE tomography based on SART has great potential in the application of structure damage detection. Finally, to further improve the quality of 3D imaging, the Median Filter and the Adaptive Median Filter are used to reduce the noises resulting from AE tomography. The experiment results indicate that Median Filter is the optimal method to remove Salt & Pepper noises.

  19. Reconstructing the Cenozoic evolution of the mantle: Implications for mantle plume dynamics under the Pacific and Indian plates

    Science.gov (United States)

    Glišović, Petar; Forte, Alessandro M.

    2014-03-01

    The lack of knowledge of the initial thermal state of the mantle in the geological past is an outstanding problem in mantle convection. The resolution of this problem also requires the modelling of 3-D mantle evolution that yields maximum consistency with a wide suite of geophysical constraints. Quantifying the robustness of the reconstructed thermal evolution is another major concern. To solve and estimate the robustness of the time-reversed (inverse) problem of mantle convection, we analyse two different numerical techniques: the quasi-reversible (QRV) and the backward advection (BAD) methods. Our investigation extends over the 65 Myr interval encompassing the Cenozoic era using a pseudo-spectral solution for compressible-flow thermal convection in 3-D spherical geometry. We find that the two dominant issues for solving the inverse problem of mantle convection are the choice of horizontally-averaged temperature (i.e., geotherm) and mechanical surface boundary conditions. We find, in particular, that the inclusion of thermal boundary layers that yield Earth-like heat flux at the top and bottom of the mantle has a critical impact on the reconstruction of mantle evolution. We have developed a new regularisation scheme for the QRV method using a time-dependent regularisation function. This revised implementation of the QRV method delivers time-dependent reconstructions of mantle heterogeneity that reveal: (1) the stability of Pacific and African ‘large low shear velocity provinces’ (LLSVP) over the last 65 Myr; (2) strong upward deflections of the CMB topography at 65 Ma beneath: the North Atlantic, the south-central Pacific, the East Pacific Rise (EPR) and the eastern Antarctica; (3) an anchored deep-mantle plume ascending directly under the EPR (Easter and Pitcairn hotspots) throughout the Cenozoic era; and (4) the appearance of the transient Reunion plume head beneath the western edge of the Deccan Plateau at 65 Ma. Our reconstructions of Cenozoic mantle

  20. Geotectonic Elements, Stuctural Constraints and Current Problems for a Kinematic Reconstruction of the Caribbean Plate Margins during the Cretaceous.

    Science.gov (United States)

    Giunta, G.

    2001-12-01

    In the Caribbean Plate deformed margins are found relics of the Mid to Late Cretaceous eo-Caribbean tectonic phases, indicating the occurrence of sub-continental subduction zones with melange formation, and HP/LT metamorphism of ophiolitic rocks, and two main stages of intraoceanic subductions involving the unthickened proto-Caribbean oceanic lithosphere and/or supra-subduction complexes. These two stages are marked by the occurrence of (a) HP/LT metamorphic ophiolites and volcano-plutonic sequences with island-arc tholeiitic (IAT) or calc-alkaline (CA) affinities; (b) unmetamorphosed tonalitic intrusions of CA affinity below the proto-Caribbean thickened oceanic plateau. Since the Late Cretaceous the kinematics of the Caribbean Plate is closely related to the eastward drifting of the proto-Caribbean oceanic plateau (Colombia and Venezuela Basins) that produced both a diachronous tonalitic magmatism from 85-82 Ma, associated with a westward dipping oblique subduction of the proto-Caribbean-Atlantic ocean floor below the plateau, and an opposite dismembering of subduction complexes, of different ages along an E-W trend (North and South Caribbean Margins). This seems to be the consequence of the eastward shifting of both the northern and southern triple junctions, while allowing further bending of the Aves- Lesser Antilles arc. Moreover, the Caribbean oceanic plateau was trapped by different rotation rates of the Chortis, Chorotega and Choco blocks, during the construction of the western plate margin (Central American Isthmus). The previous Mid-Late Cretaceous eo-Caribbean evolution, correspondent to the beginning of the compressional conditions in Central America area, is characterized by sub-continental and/or intraoceanic subduction systems with associated IAT and CA arc magmatism. This simplified kinematic approach falls short in explaining (1) the Early Cretaceous paleogeography and morphology of the margins of the North, South American continents and minor

  1. 车牌识别系统中的超分辨率图像重建技术研究%Research of super-resolution image reconstruction in license plate recognition system

    Institute of Scientific and Technical Information of China (English)

    林明儒

    2015-01-01

    针对车牌识别系统中图像模糊和分辨率低而影响车牌识别效果的问题,提出利用超分辨率重建来提高车牌图像分辨率的解决方法。建立了凸集投影(POCS)算法的数学模型,研究了凸集投影超分辨率重建的实现过程,并用仿真实验进行了验证。实验结果表明:采用凸集投影算法进行图像重建,可以提高车牌图像分辨率,丰富图像细节信息,能够有效提高车牌识别的准确率,并且迭代次数越多,图像重建效果越好。%In the license plate recognition system,blurred image and low resolution affect the effect of license plate recognition.A method which uses the super-resolution image reconstruction to improve the resolution of plate image is proposed.In this paper,mathematical model of projection onto convex sets (POCS)is estab-lished and the process of image reconstruction based on POCS is researched.Simulation experiments are con-ducted to verify the research.Experimental results show that,image reconstruction based on POCS algorithm can improve the resolution of license plate image,rich detail information of the image,enhance the vehicle license plate recognition system performance.Through the experiments,the more iterations are made,the better effects of image reconstruction appear.

  2. 髋臼横行骨折采用前后柱拉力螺钉结合重建钢板固定疗效分析%Analysis of the Effect of the Acetabular Transverse Fracture Using the Lag Screw of the Acetabulum and the Reconstruction Plate With the Reconstruction Plate

    Institute of Scientific and Technical Information of China (English)

    张立峰; 冯卫; 包道日娜; 冬梅; 佟雁翔

    2015-01-01

    Objective To investigate the clinical effect of the application of the acetabular transverse fracture in the treatment of the acetabular fracture and the reconstruction of the plate fixation with the lag screw of the acetabulum. Methods 50 cases of patients with transverse acetabular fracture were selected,and subject to acetabular posterior column lag screw combined with reconstruction plate fixation treatment,Bleeding volume,operation time, the acetabulum repositioning and hip joint function recovery after surgical of patients were observed. Results The average operation time was 3.5 hours, the average amount of bleeding was 950ml, according to Matta reduction, 25 cases of anatomic reduction, satisfactory reduction in 21 cases, 4 cases of unsatisfactory reduction, and the excellent and good rate of hip joint function was 86.0%. Conclusion The clinical effect of the acetabular transverse fracture patients with the acetabular anterior and posterior column lag screw combined with the reconstruction plate fixation is worthy of promotion.%目的:探讨对髋臼横行骨折患者应用髋臼前后柱拉力螺钉结合重建钢板固定治疗的临床疗效。方法选取髋臼横行骨折患者50例,对其进行髋臼前后柱拉力螺钉结合重建钢板固定手术治疗,观察患者手术时出血量、手术时间等,手术治疗后患者髋臼复位情况以及髋关节功能恢复情况。结果平均手术时间为3.5小时,平均出血量为950 ml,根据 matta 复位,25例解剖复位,21例满意复位,4例复位不满意,髋关节功能优良率为86.0%。结论对髋臼横行骨折患者采取髋臼前后柱拉力螺钉结合重建钢板固定手术治疗临床疗效突出。

  3. 重建锁定接骨钢板治疗肩胛骨骨折的临床效果观察%Observation of clinical effect by reconstruction locking plate in the treatment of scapular fracture

    Institute of Scientific and Technical Information of China (English)

    魏树刚

    2015-01-01

    ObjectiveTo research and analyze clinical effect by reconstruction locking plate in the treatment of scapular fracture.MethodsA total of 68 scapular fracture patients were randomly divided into reconstruction fixation group and locking fixation group, with 34 cases in each group. The reconstruction fixation group received reconstruction locking plate for treatment, and the locking fixation group received T-type locking titanium plate internal fixation. Curative effects of the two groups were recorded and compared.ResultsThe reconstruction fixation group had total effective rate as 97.06%, and the locking fixation group had that as 70.59%. The reconstruction fixation group had obviously higher total effective rate than the locking fixation group, and their difference had statistical significance (P<0.05).ConclusionReconstruction locking plate provides precise effect in treating scapular fracture, and it is worthy of clinical promotion.%目的:研究分析采用重建锁定接骨钢板技术治疗肩胛骨骨折的临床效果。方法68例肩胛骨骨折患者随机分为重建固定组和锁定固定组,各34例。其中重建固定组给予重建锁定接骨钢板治疗,锁定固定组给予T型锁定钛板内固定治疗,分别记录两组患者的治疗效果,并比较。结果重建固定组总有效率为97.06%,锁定固定组总有效率为70.59%,重建固定组总有效率明显高于锁定固定组,差异具有统计学意义(P<0.05)。结论重建锁定接骨钢板技术治疗肩胛骨骨折效果明显,值得临床推广。

  4. Obliquity along plate boundaries

    Science.gov (United States)

    Philippon, Mélody; Corti, Giacomo

    2016-12-01

    Most of the plate boundaries are activated obliquely with respect to the direction of far field stresses, as roughly only 8% of the plate boundaries total length shows a very low obliquity (ranging from 0 to 10°, sub-orthogonal to the plate displacement). The obliquity along plate boundaries is controlled by (i) lateral rheological variations within the lithosphere and (ii) consistency with the global plate circuit. Indeed, plate tectonics and magmatism drive rheological changes within the lithosphere and consequently influence strain localization. Geodynamical evolution controls large-scale mantle convection and plate formation, consumption, and re-organization, thus triggering plate kinematics variations, and the adjustment and re-orientation of far field stresses. These geological processes may thus result in plate boundaries that are not perpendicular but oblique to the direction of far field stresses. This paper reviews the global patterns of obliquity along plate boundaries. Using GPlate, we provide a statistical analysis of present-day obliquity along plate boundaries. Within this framework, by comparing natural examples and geological models, we discuss deformation patterns and kinematics recorded along oblique plate boundaries.

  5. Ridge-spotting: A new test for Pacific absolute plate motion models

    Science.gov (United States)

    Wessel, Paul; Müller, R. Dietmar

    2016-06-01

    Relative plate motions provide high-resolution descriptions of motions of plates relative to other plates. Yet geodynamically, motions of plates relative to the mantle are required since such motions can be attributed to forces (e.g., slab pull and ridge push) acting upon the plates. Various reference frames have been proposed, such as the hot spot reference frame, to link plate motions to a mantle framework. Unfortunately, both accuracy and precision of absolute plate motion models lag behind those of relative plate motion models. Consequently, it is paramount to use relative plate motions in improving our understanding of absolute plate motions. A new technique called "ridge-spotting" combines absolute and relative plate motions and examines the viability of proposed absolute plate motion models. We test the method on six published Pacific absolute plate motions models, including fixed and moving hot spot models as well as a geodynamically derived model. Ridge-spotting reconstructs the Pacific-Farallon and Pacific-Antarctica ridge systems over the last 80 Myr. All six absolute plate motion models predict large amounts of northward migration and monotonic clockwise rotation for the Pacific-Farallon ridge. A geodynamic implication of our ridge migration predictions is that the suggestion that the Pacific-Farallon ridge may have been pinned by a large mantle upwelling is not supported. Unexpected or erratic ridge behaviors may be tied to limitations in the models themselves or (for Indo-Atlantic models) discrepancies in the plate circuits used to project models into the Pacific realm. Ridge-spotting is promising and will be extended to include more plates and other ocean basins.

  6. Accurate pattern registration for integrated circuit tomography

    Energy Technology Data Exchange (ETDEWEB)

    Levine, Zachary H.; Grantham, Steven; Neogi, Suneeta; Frigo, Sean P.; McNulty, Ian; Retsch, Cornelia C.; Wang, Yuxin; Lucatorto, Thomas B.

    2001-07-15

    As part of an effort to develop high resolution microtomography for engineered structures, a two-level copper integrated circuit interconnect was imaged using 1.83 keV x rays at 14 angles employing a full-field Fresnel zone plate microscope. A major requirement for high resolution microtomography is the accurate registration of the reference axes in each of the many views needed for a reconstruction. A reconstruction with 100 nm resolution would require registration accuracy of 30 nm or better. This work demonstrates that even images that have strong interference fringes can be used to obtain accurate fiducials through the use of Radon transforms. We show that we are able to locate the coordinates of the rectilinear circuit patterns to 28 nm. The procedure is validated by agreement between an x-ray parallax measurement of 1.41{+-}0.17 {mu}m and a measurement of 1.58{+-}0.08 {mu}m from a scanning electron microscope image of a cross section.

  7. Kinematic reconstruction of the Caribbean region since the Early Jurassic

    Science.gov (United States)

    Bochman, Lydian; van Hinsbergen, Douwe; Torsvik, Trond; Spakman, Wim; Pindell, James

    2014-05-01

    The Caribbean region results from a complex tectonic history governed by the interplay of the North American, South American and (Paleo-)Pacific plates, between which the Caribbean plate evolved since the early Cretaceous. During its entire tectonic evolution, the Caribbean plate was largely surrounded by subduction and transform boundaries, which hampers a quantitative integration into the global circuit of plate motions. In addition, reconstructions of the region have so far not resulted in a first order kinematic description of the main tectonic units in terms of Euler poles and finite rotation angles. Here, we present an updated, quantitatively described kinematic reconstruction of the Caribbean region back to 200 Ma integrated into the global plate circuit, and implemented with GPlates free software. Our analysis of Caribbean tectonic evolution incorporates an extensive literature review. To constrain the Caribbean plate motion between the American continents, we use a novel approach that takes structural geological observations rather than marine magnetic anomalies as prime input, and uses regionally extensive metamorphic and magmatic phenomena such as the Great Arc of the Caribbean, the Caribbean Large Igneous Province (CLIP) and the Caribbean high-pressure belt as correlation markers. The resulting model restores the Caribbean plate back along the Cayman Trough and major strike-slip faults in Guatemala, offshore Nicaragua, offshore Belize and along the Northern Andes towards its position of origin, west of the North and South American continents in early Cretaceous time. We provide the paleomagnetic reference frame for the Caribbean region by rotating the Global Apparent Polar Wander Path into coordinates of the Caribbean plate interior, Cuba, and the Chortis Block. We conclude that a plate kinematic scenario for a Panthalassa/Pacific origin of Caribbean lithosphere leads to a much simpler explanation than a Proto-Caribbean/Atlantic origin. Placing our

  8. An Equivalent Circuit for Landau Damping

    DEFF Research Database (Denmark)

    Pécseli, Hans

    1976-01-01

    An equivalent circuit simulating the effect of Landau damping in a stable plasma‐loaded parallel‐plate capacitor is presented. The circuit contains a double infinity of LC components. The transition from stable to unstable plasmas is simulated by the introduction of active elements into the circuit....

  9. Algebraic circuits

    CERN Document Server

    Lloris Ruiz, Antonio; Parrilla Roure, Luis; García Ríos, Antonio

    2014-01-01

    This book presents a complete and accurate study of algebraic circuits, digital circuits whose performance can be associated with any algebraic structure. The authors distinguish between basic algebraic circuits, such as Linear Feedback Shift Registers (LFSRs) and cellular automata, and algebraic circuits, such as finite fields or Galois fields. The book includes a comprehensive review of representation systems, of arithmetic circuits implementing basic and more complex operations, and of the residue number systems (RNS). It presents a study of basic algebraic circuits such as LFSRs and cellular automata as well as a study of circuits related to Galois fields, including two real cryptographic applications of Galois fields.

  10. 前路钛板结合方形区螺钉内固定治疗涉及方形区的髋臼骨折%Quadrilateral plate fractures of the acetabulum treated by internal fixation with reconstruction titanium plate combined with trans-plate quadrilateral screws via the ilioinguinal approach

    Institute of Scientific and Technical Information of China (English)

    蔡贤华; 刘曦明; 汪国栋; 徐峰; 王华松; 李世梁; 黄大伟; 徐洲发

    2013-01-01

    目的 探讨前路钛板结合方形区螺钉内固定治疗涉及方形区的髋臼骨折的疗效. 方法 2005年1月至2011年5月共收治52例涉及方形区的髋臼骨折患者,其中36例获得随访,男21例,女15例;年龄21~59岁,平均43.5岁.骨折按Letournel分型:双柱骨折15例,横形骨折4例,前柱伴后半横形骨折8例,T形骨折9例.所有患者均采用髂腹股沟入路,复位后行重建钛板及经钛板3 ~5枚皮质骨螺钉(方形区螺钉)部分经骨表面内固定.术后应用Matta放射学标准评估骨折复位质量,末次随访时采用改良Merle d'Aubigné和Postel评分标准评定髋关节功能. 结果 36例患者术后获12 ~ 72个月(平均41.7个月)随访.术后骨折复位质量按Matta放射学标准评定:解剖复位19例,良好复位12例,不满意复位5例,复位优良率为86.1%.所有患者骨折均获临床愈合,愈合时间为2~4个月,平均3个月.末次随访时采用改良Merle d'Aubigné和Postel评分标准评定髋关节功能:优16例,良13例,可5例,差2例,优良率为80.6%.本组患者功能优良率与骨折复位质量呈明显正相关(r=0.513,P=0.001).无一例患者发生方形区螺钉松脱、断裂.结论 前路钛板结合方形区螺钉内固定可靠,无进入髋关节腔之虞,是治疗以前柱损伤为主的双柱骨折、向前移位的横形骨折、部分前柱合并后半横形骨折及部分T形骨折的有效方法之一.%Objective To explore the clinical efficacy of internal fixation using reconstruction titanium plate combined with trans-plate quadrilateral screws in treatment of quadrilateral plate fractures of the acetabulum via the ilioinguinal approach.Methods Of the 52 quadrilateral plate fractures of the acetabulum which had been treated between January 2005 and May 2011,36 cases were followed up.They were 21 males and 15 females,with an average age of 43.5 years (from 21 to 59 years).By Letournel's classification,there were 15 double

  11. Are chest compressions safe for the patient reconstructed with sternal plates? Evaluating the safety of cardiopulmonary resuscitation using a human cadaveric model

    Directory of Open Access Journals (Sweden)

    McKay Douglas R

    2010-08-01

    Full Text Available Abstract Background Plate and screw fixation is a recent addition to the sternal wound treatment armamentarium. Patients undergoing cardiac and major vascular surgery have a higher risk of postoperative arrest than other elective patients. Those who undergo sternotomy for either cardiac or major vascular procedures are at a higher risk of postoperative arrest. Sternal plate design allows quick access to the mediastinum facilitating open cardiac massage, but chest compressions are the mainstay of re-establishing cardiac output in the event of arrest. The response of sternal plates and the chest wall to compressions when plated has not been studied. The safety of performing this maneuver is unknown. This study intends to demonstrate compressions are safe after sternal plating. Methods We investigated the effect of chest compressions on the plated sternum using a human cadaveric model. Cadavers were plated, an arrest was simulated, and an experienced physician performed a simulated resuscitation. Intrathoracic pressure was monitored throughout to ensure the plates encountered an appropriate degree of force. The hardware and viscera were evaluated for failure and trauma respectively. Results No hardware failure or obvious visceral trauma was observed. Rib fractures beyond the boundaries of the plates were noted but the incidence was comparable to control and to the fracture incidence after resuscitation previously cited in the literature. Conclusions From this work we believe chest compressions are safe for the patient with sternal plates when proper plating technique is used. We advocate the use of this life-saving maneuver as part of an ACLS resuscitation in the event of an arrest for rapidly re-establishing circulation.

  12. Hierarchical self-organization of tectonic plates

    OpenAIRE

    2010-01-01

    The Earth's surface is subdivided into eight large tectonic plates and many smaller ones. We reconstruct the plate tessellation history and demonstrate that both large and small plates display two distinct hierarchical patterns, described by different power-law size-relationships. While small plates display little organisational change through time, the structure of the large plates oscillate between minimum and maximum hierarchical tessellations. The organization of large plates rapidly chan...

  13. Clinical Application of Treatment of Middle Clavicular Fractures With Reconstruction Plate Placed Eccentric%重建钢板治疗锁骨中段骨折56例临床分析

    Institute of Scientific and Technical Information of China (English)

    刘德祥

    2012-01-01

      目的探究重建钢板对锁骨中断骨折的临床疗效.方法回顾分析我科2008年4月至2011年4月收治的56例锁骨中断骨折并接受重建钢板治疗的患者临床资料,记录骨折愈合、相关并发症及肩关节功能恢复情况.结果56例患者均骨折愈合,平均2-7个月,无不愈合出现.其中优31例(55.35%),良19例(33.92%),中6例(10.7%),无差.结论重建钢板能有效固定骨折远端,促进功能恢复,并能减少骨不愈合和锁骨缩短的优点,值得在临床推广.%  Objective: To investigate the effect of middle clavicular fractures with reconstruction plate placed eccentric and multi-angle,multi-way direction of the screw screwed ;Methods: 32 patients with reconstruction plate placed eccentric were folowed up ,then to record fracture healing,complications and joint function recovery; Results:According to the standard floating shoulder function score (Herscovici Standard): excelent in 31 cases (55.35%),good 19 cases(33.92%),moderate 6 cases (10.7%). Conclusion:The reconstruction plate eccentric place is the most effective method for middle clavicular fractures. focusing on the intrinsic biomechanical factors and strengthening the effective fracture fixation.It is helpful for early physical exercise and deserves more wide application.

  14. Reconstructing the medial collateral ligament with star-shaped titanium plate%星形钛板在膝关节内侧副韧带断裂修复中的应用

    Institute of Scientific and Technical Information of China (English)

    尹航; 赵蕾; 董黎强

    2015-01-01

    Objective To evaluate the clinical effect of the application of star-shaped titanium plate in reconstructing the medial collateral ligament.Method 12 cases of broken medial collateral ligament were reconstructed with star titanium plates.The injury part of medial collateral ligament was fixed on the bone by screw.The normal part of medial collateral ligament was fastened with radial hooks of star-shaped titanium plate.Findings Follow-up at 10 ~15 months after treatment indicated that the function of the knee joint had been recovered well and posed no draw-back on daily life.X-ray review also indicated that no breakage of star-shaped titanium plate or loosen screw fixation were found.Conclusion The application of star-shaped titanium plate in reconstructing broken medial collateral ligament can improve the stability of the knee and reduce the risk of ligament rupture again.%目的:探讨星形钛板在膝关节内侧副韧带断裂中的应用,并观察其临床疗效。方法采用星形钛板治疗膝关节内侧副韧带附着处断裂患者12例,螺钉固定使韧带损伤部分与骨质紧密结合,放射状齿钩将韧带正常部分扣紧于骨组织。结果随访时间为10~15个月,膝关节功能恢复良好,日常生活无影响。复查 X 线片未见明显内固定松动、退钉、断钉或星形钛板断裂。结论应用星形钛板治疗膝关节内侧副韧带断裂可以良好地恢复膝关节的稳定性,降低韧带再次断裂的风险。

  15. Image Noise, CNR, and Detectability of Low-Contrast, Low-Attenuation Liver Lesions in a Phantom: Effects of Radiation Exposure, Phantom Size, Integrated Circuit Detector, and Iterative Reconstruction.

    Science.gov (United States)

    Goenka, Ajit H; Herts, Brian R; Dong, Frank; Obuchowski, Nancy A; Primak, Andrew N; Karim, Wadih; Baker, Mark E

    2016-08-01

    Purpose To assess image noise, contrast-to-noise ratio (CNR) and detectability of low-contrast, low-attenuation liver lesions in a semianthropomorphic phantom by using either a discrete circuit (DC) detector and filtered back projection (FBP) or an integrated circuit (IC) detector and iterative reconstruction (IR) with changes in radiation exposure and phantom size. Materials and Methods An anthropomorphic phantom without or with a 5-cm-thick fat-mimicking ring (widths, 30 and 40 cm) containing liver inserts with four spherical lesions was scanned with five exposure settings on each of two computed tomography scanners, one equipped with a DC detector and the other with an IC detector. Images from the DC and IC detector scanners were reconstructed with FBP and IR, respectively. Image noise and lesion CNR were measured. Four radiologists evaluated lesion presence on a five-point diagnostic confidence scale. Data analyses included receiver operating characteristic (ROC) curve analysis and noninferiority analysis. Results The combination of IC and IR significantly reduced image noise (P < .001) (with the greatest reduction in the 40-cm phantom and at lower exposures) and improved lesion CNR (P < .001). There was no significant difference in area under the ROC curve between detector-reconstruction combinations at fixed exposure for either phantom. Reader accuracy with IC-IR was noninferior at 50% (100 mAs [effective]) and 25% (300 mAs [effective]) exposure reduction for the 30- and 40-cm phantoms, respectively (adjusted P < .001 and .04 respectively). IC-IR improved readers' confidence in the presence of a lesion (P = .029) independent of phantom size or exposure level. Conclusion IC-IR improved objective image quality and lesion detection confidence but did not result in superior diagnostic accuracy when compared with DC-FBP. Moderate exposure reductions maintained comparable diagnostic accuracy for both detector-reconstruction combinations. Lesion detection in the 40

  16. H 形钢板固定骶髂关节分离的生物力学评价%Biomechanical assessment on internal fixation with H-shaped reconstruc-tion plate for sacroiliac joint dislocation

    Institute of Scientific and Technical Information of China (English)

    廖文胜; 丁强; 王利民

    2013-01-01

    目的:设计针对骶髂关节脱位内固定治疗的H形钢板,并行生物力学评价。方法:根据解剖特点,设计并制作适用于骶髂关节脱位的H形钢板。收集12个成年防腐骨盆标本,切断骶髂前韧带、骶髂后韧带和骶髂骨间韧带,制作成12对骶髂关节分离模型并随机分为两组,分别使用H形钢板固定和传统的双钢板固定。应用万能生物力学试验机,分别测量侧方和垂直方向上骶髂关节间位移1、2和3 mm时所需要的载荷。结果:在侧方位移1、2和3 mm和垂直位移1 mm时,H形钢板固定组所需载荷均大于传统双钢板固定组(t=4.774,4.202,5.561和2.793,P<0.05)。垂直位移2和3 mm时,两组间所需载荷差异无统计学意义(t=1.362,0.775,P>0.05)。结论:H形钢板应用于骶髂关节分离的固定时,对抗旋转和垂直方向上的初始移位的能力更强,具有更好的力学稳定性。%Aim:To design H-shaped reconstruction plate for the fixation of sacroiliac joint dislocation and to observe its biomechanical characteristics .Methods:H-shaped reconstruction plate was designed based on anatomical features of sacroiliac joint .A total of 12 pelvises of cadaver were achieved ,and dissected sagittally through the midline of the sacrum and the pubic symphysis .All ligaments surrounding the sacroiliac joints were removed .12 pairs of sacroiliac joint disloca-tion model were obtained and divided into two groups randomly .Six samples(Group A)were fixed with H-shaped plates and 4 screws,another 6 samples(Group B)were fixed with two traditional reconstruction plates and 4 screws.Then biomechani-cal tests were performed to measure the loading force at the different displacement (1, 2, and 3 mm) in the lateral and ver-tical direction, respectively.Results:The loading force of Group A was larger than that of Group B at 1,2 and 3 mm dis-placement in lateral direction and 1 mm

  17. Uso de placas de ácido poli-L-láctico en reconstrucción de pared torácica Use of poly-L-lactic plates in chest wall reconstruction

    Directory of Open Access Journals (Sweden)

    J. Vilà Poyatos

    2011-12-01

    Full Text Available La reconstrucción de la pared torácica exige un amplio conocimiento de las técnicas reconstructivas y un buen plan operatorio. Por una parte es necesario mantener la estabilidad de la caja torácica y por otro proporcionar una buena base para la cobertura dérmica o musculocutánea que confiera buenos resultados funcionales y plásticos. En este trabajo describimos 2 casos clínicos en los que la reconstrucción de la pared torácica anterior se realizó con placas de ácido poli-L-láctico sobre las que se colocaron sendos colgajos musculocutáneos.Chest wall reconstruction requires an extensive knowledge of reconstructive techniques and a good surgical plan. On one hand, it is necessary to maintain stability of the rib cage and, on the other, provide a good foundation for dermal coverage or musculocutaneous flaps which confers good functional and plastic results. In this article we describe 2 cases in which anterior chest wall reconstruction was performed with plates of poly-L-lactic acid, on which were placed the musculocutaneous flaps.

  18. 重建钢板偏心性放置内固定术治疗锁骨中段骨折的临床应用%Clinical application of treatment of middle clavicular fractures with eccentrically placed reconstruction plate

    Institute of Scientific and Technical Information of China (English)

    洪斌; 奥沛源; 任学通; 梁嘉樑; 南晶

    2011-01-01

    目的 探讨重建钢板偏心性放置内固定治疗锁骨中段骨折的疗效.方法 选择2008年1月至2009年12月32例锁骨中段骨折的患者.进行重建钢板偏心性放置内固定术治疗,观察骨折愈合、并发症及肩关节功能恢复情况.结果 32例全部达到骨性愈合,未出现脱钉、钢板折弯、断裂等情况.按漂浮肩功能评分标准(Herscoviei标准)进行功能分级,优22例,良7例,可3例,优良率为90.63%.结论 重建钢板偏心性放置加强了骨折远端的有效固定,可早期进行功能锻炼,是一种值得推荐的术式.%Objective To investigate the effect of middle clavicular fractures with eccentrically placed reconstruction plate and multi-angle, multi-directional of the screw. Methods Thirty-two patients with reconstruction plate placed eccentrially were followed up, then the fracture healing rate, complications and joint function recovery were analyzed. Results According to the standard floating shoulder function score (Herscovici Standard), 22 cases could be scored excellent, 7 cases could be scored good, 3 cases could be scored to be fair and none to be poor, the excellent rate was 90.63%.Conclusions The reconstruction plate placed eccentrically is the most effective treatment method for middle clavicular fractures. This approach enhances the intrinsic biomechanical factors and strengthens the fracture fixation. It is helpful for early physical exercise and merits wide application.

  19. The clinical efficacy of dural reconstruction plates for treatment of humeral intercandylar fracture%双重建钢板内固定治疗肱骨髁间骨折的临床疗效观察

    Institute of Scientific and Technical Information of China (English)

    王立东; 王健; 于从军

    2014-01-01

    Objective To investigate the of dural reconstruction plates for treatment of humeral intercandylar fracture.Methods The 52 cases with humeral intercandylar fracture were treated with dural reconstruction plates internal fixation.Watched the clinical efficacy Postoperative in outpatient,and guide early exercise of elbow.Result Using Elbow Scoring Standard System to assess:16 cases of C1,excellent and good in 14 cases,fair in 2 cases,and 87.5% excellent and good results were obtained.Twenty-four cases of C2,excellent and good in 20 cases,fair in 4 cases,and 83.3% excellent and good results were obtained.Twelve cases of C3,excellent and good in 6 cases,fair in 2 cases,and poor in 4 case,and 50.0% excellent and good results were obtained.Fifty-two cases were followed up,excellent and good in 40 cases,fair in 8 cases,and poor in 4 case,and 76.9% excellent and good results were obtained.Conclusion Dural reconstruction plates internal fixation was the relatively effective method for treatment of humural intercandylar fracture.%目的 探讨双重建钢板治疗肱骨髁间骨折的临床疗效.方法 收集2006年2月至2012年9月肱骨髁间骨折病例52例,均采用双重建钢板固定,术后门诊随访,指导肘关节功能锻炼.结果 按肘关节评分标准评定:C1型16例,优良14例,可2例,优良率为87.5%.C2型24例,优良20例,可4例,优良率为83.3%.C3型12例,优良6例,可2例,差4例,优良率为50.0%,总优良40例,可8例,差4例,总优良率为76.9%.结论 双重建钢板内固定术是治疗肱骨髁间骨折相对有效的方法.

  20. 记忆合金骑缝钉联合重建钛板治疗骨盆骨折%Treatment of unstable pelvic fractures with reconstructive plates and shape memory alloy staples

    Institute of Scientific and Technical Information of China (English)

    王愉思; 贾真; 魏磊平; 徐勇强; 阎戈; 康亦峰; 刘宏哲; 王靖; 黄焱; 何畔

    2011-01-01

    Objective To discuss clinical efficacy of reconstructive plates and shape memory alloy staples in the treatment of unstable pelvic fractures.Methods From February 2002 to December 2008,53 patients with unstable pelvic fracture were treated with reconstructive plates and shape memory alloy staples.They were 25 men and 28 women,aged from 17 to 76 years (average,41 years).According to the Tile classification,there were 34 cases of Tile B and 19 cases of Tile C.Results All the patients were followed up for an average of 24 months (range,form 6 to 48 months).According to the Matta evaluation system,46 patients obtained excellent reduction and 7 good reduction.By the Majeed evaluation system,37patients achieved excellent functional recovery,12 good and 3 fair,with a good to excellent rate of 92.5%.Conclusion Internal fixation with reconstructive plates and shape memory alloy staples is an effective treatment of unstable pelvic fractures.%目的 探讨记忆合金骑缝钉联合重建钛板治疗骨盆骨折的效果.方法 回顾性分析2002年2月至2008年12月应用记忆合金骑缝钉联合重建钛板治疗53例不稳定型骨盆骨折患者的临床资料,男25例,女28例;年龄17~76岁,平均41岁.根据Tile分型:B型34例,C型19例.结果 所有患者术后获6~48个月(平均24个月)随访.术后按Matta标准评定骨折复位疗效:46例获解剖复位,7例接近解剖复位,无不满意复位患者;关节功能按照Majeed功能评价标准评定疗效:优37例,良12例,可3例,差1例,优良率为92.5%.结论 采用记忆合金骑缝钉联合重建钛板治疗骨盆骨折能获得较好的疗效.

  1. Resonance circuits for adiabatic circuits

    Directory of Open Access Journals (Sweden)

    C. Schlachta

    2003-01-01

    Full Text Available One of the possible techniques to reduces the power consumption in digital CMOS circuits is to slow down the charge transport. This slowdown can be achieved by introducing an inductor in the charging path. Additionally, the inductor can act as an energy storage element, conserving the energy that is normally dissipated during discharging. Together with the parasitic capacitances from the circuit a LCresonant circuit is formed.

  2. Experimental biomechanical analysis of standing position in both-column acetabular fractures fixed by anterior reconstruction plate combinated with trans-plate quadrilateral screws%前路钛板加方形区螺钉治疗髋臼双柱骨折的站立位力学分析

    Institute of Scientific and Technical Information of China (English)

    蔡贤华; 吴咏德; 刘曦明; 张红喜

    2013-01-01

    [目的]探讨前路特殊塑形钛板加方形区螺钉治疗髋臼双柱骨折早期站立的可能性.[方法]选取成年防腐保湿处理的全骨盆标本6具,保留韧带及髋关节囊,制作单侧髋臼高位双柱骨折模型,随机先后采用前路特殊塑形钛板加方形区螺钉(B组)及常规塑形钛板加1/3管型钛板(C组)内固定,固定标本于ZWICKZ100电子万能材料试验机上,模拟站立位以400~700 N垂直加载,分别测定完整骨盆(A组)、B组及C组后柱内壁横向位移、髋臼顶纵向位移,并计算刚度.[结果]随着载荷增加,各位移值呈逐渐增加的线性关系,且A组<B组<C组;在生理负荷600N载荷下,横向与纵向位移值均为C组>B组>A组、刚度为C组>B组>A组,C组与B组、A组与C组间差异明显(P<0.05),B组与A组差异无显著意义(P>0.05).[结论]站立位下,前路特殊塑形钛板加方形区螺钉较常规塑形钛板加1/3管型钛板内固定即刻力学性能更为可靠,稳定性与完整骨盆接近,这表明早期站立并不影响前路特殊塑形钛板加方形区螺钉内固定的稳定性.%[ Objective] To explore the standing possibility in the early after both - column acetabular fracture fixed by anterior specially - shaped reconstruction plate combinated with trans - plate quadrilateral screws on cadaver. [ Method] Six Chinese adult wetly pelvic specimens with their ligament and joint capsule of hip joint preserved with antisepsis were made into the model with high both-column acetabular fracture on one side. The fractures were fixed randomly by anterior specially-shaped titanium plate with quadrilateral screws( group B) or conventionally-shaped reconstruction titanium plate with 1/3 tubular titanium plate (group C). To imitate the static standing position of the patient,the specimen fixed on ZWICK-Z100 electronic universal material testing machine received the vertical loading from 400 N to 700 N to measure the transverse displacement of

  3. Reconciling geodetic and geologic estimates of recent plate motion across the Southwest Indian Ridge

    Science.gov (United States)

    DeMets, C.; Calais, E.; Merkouriev, S.

    2016-10-01

    We use recently published, high-resolution reconstructions of the Southwest Indian Ridge to test whether a previously described systematic difference between Global Positioning System (GPS) and 3.16-Myr-average estimates of seafloor spreading rates between Antarctica and Africa is evidence for a recent slowdown in Southwest Indian Ridge seafloor spreading rates. Along the Nubia-Antarctic segment of the ridge, seafloor opening rates that are estimated with the new, high-resolution reconstructions and corrected for outward displacement agree well with geodetic rate estimates and reduce previously reported, highly significant non-closure of the Nubia-Antarctic-Sur plate circuit. The observations are inconsistent with a slowdown in spreading rates and instead indicate that Nubia-Antarctic plate motion has been steady since at least 5.2 Ma. Lwandle-Antarctic seafloor spreading rates that are estimated from the new high-resolution reconstructions differ insignificantly from a GPS estimate, thereby implying steady Lwandle-Antarctic plate motion since 5.2 Ma. Between the Somalia and Antarctic plates, the new Southwest Indian Ridge reconstructions eliminate roughly half of the systematic difference between the GPS and MORVEL spreading rate estimates. We interpret the available observations as evidence that Somalia-Antarctic spreading rates have been steady since at least 5.2 Ma and postulate that the remaining difference is attributable to random and/or systematic errors in the plate kinematic estimates and the combined effects of insufficient geodetic sampling of undeforming areas of the Somalia plate, glacial isostatic adjustment in Antarctica, and transient deformation triggered by the 1998 Mw=8.2 Antarctic earthquake, the 2004 Mw=9.3 Sumatra earthquake, or possibly other large historic earthquakes.

  4. APPLICATION OF TITANIUM PLATE AND Teflon PATCH IN CHEST WALL RECONSTRUCTION AFTER STERNAL TUMOR RESECTION%钛板联合Teflon补片重建胸骨肿瘤切除后胸廓

    Institute of Scientific and Technical Information of China (English)

    吴显宁; 陈名久; 喻风雷

    2011-01-01

    Objective To study the reconstruction method and effectiveness of titanium plate and Teflon patch for the chest wall after resection of sternal tumors. Methods Between October 2006 and November 2009, 4 patients with sternal tumors were treated and the thoracic cages were reconstructed. There were 2 males and 2 females, aged 30-55 years. The patients were admitted because of chest lump or pain. The sizes of palpable lump ranged from 4 cm×3 cm to 10 cm×8 cm. CT examination showed bone destruction. After sternal tumor resection, defect size ranged from 10 cm x 8 cm to 18 cm×4 cm, and titanium plate and Teflon patch were used to repair and reconstruct the chest wall defect. Results The operations of the tumor resection and reconstruction of chest wall defect were successfully performed in 4 cases. Incisions healed by first intention with no abnormal breath, subcutaneous emphysema, pneumothorax, and infection. One case failed to be followed up after 6 months; 1 case died of intracranial hemorrhage; and 2 cases were followed up 1 and 4 years respectively without tumor recurrence. The chest wall had good remodeling. No loosening and exposure of titanium plate, difficulty in breathing, chest distress, and chest pain were observed during follow-up. Conclusion Surgical resection of sternal tumors will cause large chest wall defect which can be repaired by titanium plate and Teflon patch because it had the advantages of easy operation, satisfactory remodeling, and less complication.%目的 探讨胸骨肿瘤切除术后采用钛板联合Teflon补片重建胸廓的方法及疗效.方法 2006年10月-2009年11月,收治4例胸骨肿瘤患者.男2例,女2例;年龄30~55岁.以胸部肿块、疼痛1~6个月后入院.检查见胸前区范围为4cm×3em~10cm×8cm的肿块,质硬.CT检查见骨质破坏.采用胸骨肿瘤扩大切除术,切除范围为10cm×8cm~18em×14cm,采用钛板联合Teflon补片重建胸廓.结果 患者手术均顺利完成.术后切口Ⅰ期

  5. GATING CIRCUITS

    Science.gov (United States)

    Merrill, L.C.

    1958-10-14

    Control circuits for vacuum tubes are described, and a binary counter having an improved trigger circuit is reported. The salient feature of the binary counter is the application of the input signal to the cathode of each of two vacuum tubes through separate capacitors and the connection of each cathode to ground through separate diodes. The control of the binary counter is achieved in this manner without special pulse shaping of the input signal. A further advantage of the circuit is the simplicity and minimum nuruber of components required, making its use particularly desirable in computer machines.

  6. Clinical application of canal wall reconstruction with homograft cortical bone plate in canal wall down tympanoplasty%自体皮质骨外耳道重建在开放式鼓室成形术中的应用

    Institute of Scientific and Technical Information of China (English)

    马喆; 习国平; 张社江; 蔡爱军; 郝艳芳; 梁宝莲

    2012-01-01

    目的 对开放式鼓室成形术中利用自体皮质骨行外耳道重建的方法及疗效进行评价.方法 将接受手术治疗的胆脂瘤型中耳炎患者49例(49耳)分为两组.实验组,行开放式鼓室成形术+自体皮质骨外耳道重建术25例(耳);对照组,行常规开放式鼓室成形术+耳甲腔成形术24例(耳).术后随访6 ~ 36个月,观察两组患者术后听力结果、干耳率情况.结果 以术后语言频率气骨导差缩小>15 dB或气导听阈<40 dB为有效标准,实验组有效率68% (17/25),对照组有效率62.5% (15/24),组间比较无统计学意义(x2=0.1635,P>0.05).实验组干耳率为92.5%(23/25),明显高于对照组58.33%(14/24),差异有统计学意义(x2=4.363 6,P <0.05).实验组重建后的外耳道结构正常,无闭锁或狭窄情况发生.中耳乳突腔均接近正常.全部病例均无胆脂瘤复发.结论 开放式鼓室成形术加自体皮质骨外耳道重建术,能有效清除中耳病灶组织、恢复外耳道和中耳的结构,术后听力结果满意,干耳率高,是较为理想的手术方式.%Objective To evaluate the therapy of canal wall down tympanoplasty and canal reconstruction with homo-graft cortical bone plate. Methods Retrospective case review. 49 patients were divided into 2 groups. The experimental group that included 25 ears underwent canal wall down tympanoplasty and canal reconstruction with homograft cortical bone plate, while the control group that included 24 ears underwent regular canal wall down tympanoplasty with canal reconstruction. Follow up lasted 6-36 months and postoperative hearing and dry ear rate were evaluated. Results The criteria for success were defined as AB gap closure over 15 dB HL or air conduction threshold less than 40 dB HL (using the mean of 0. 5-, 1-, and 2-KHz threshold values). The experimental group's effective rate was 68% (17/25) and the control group's was 62. 5% (15/24). No significant difference was found between the

  7. Fractional linear systems and electrical circuits

    CERN Document Server

    Kaczorek, Tadeusz

    2015-01-01

    This monograph covers some selected problems of positive and fractional electrical circuits composed of resistors, coils, capacitors and voltage (current) sources. The book consists of 8 chapters, 4 appendices and a list of references. Chapter 1 is devoted to fractional standard and positive continuous-time and discrete-time linear systems without and with delays. In chapter 2 the standard and positive fractional electrical circuits are considered and the fractional electrical circuits in transient states are analyzed.  Descriptor linear electrical circuits and their properties are investigated in chapter 3,  while chapter 4 is devoted to the stability of fractional standard and positive linear electrical circuits. The reachability, observability and reconstructability of fractional positive electrical circuits and their decoupling zeros are analyzed in chapter 5. The fractional linear electrical circuits with feedbacks are considered in chapter 6. In chapter 7 solutions of minimum energy control for standa...

  8. Controllable circuit

    DEFF Research Database (Denmark)

    2010-01-01

    A switch-mode power circuit comprises a controllable element and a control unit. The controllable element is configured to control a current in response to a control signal supplied to the controllable element. The control unit is connected to the controllable element and provides the control...

  9. Inkjet deposited circuit components

    Science.gov (United States)

    Bidoki, S. M.; Nouri, J.; Heidari, A. A.

    2010-05-01

    All-printed electronics as a means of achieving ultra-low-cost electronic circuits has attracted great interest in recent years. Inkjet printing is one of the most promising techniques by which the circuit components can be ultimately drawn (i.e. printed) onto the substrate in one step. Here, the inkjet printing technique was used to chemically deposit silver nanoparticles (10-200 nm) simply by ejection of silver nitrate and reducing solutions onto different substrates such as paper, PET plastic film and textile fabrics. The silver patterns were tested for their functionality to work as circuit components like conductor, resistor, capacitor and inductor. Different levels of conductivity were achieved simply by changing the printing sequence, inks ratio and concentration. The highest level of conductivity achieved by an office thermal inkjet printer (300 dpi) was 5.54 × 105 S m-1 on paper. Inkjet deposited capacitors could exhibit a capacitance of more than 1.5 nF (parallel plate 45 × 45 mm2) and induction coils displayed an inductance of around 400 µH (planar coil 10 cm in diameter). Comparison of electronic performance of inkjet deposited components to the performance of conventionally etched items makes the technique highly promising for fabricating different printed electronic devices.

  10. Digital integrated circuits

    Science.gov (United States)

    Polasek, P.; Halamik, J.

    1984-05-01

    The term semicustom designed integrated circuits denotes integrated circuits of an all purpose character in which the production of chips is completed by using one to three custom design stencil type exposure masks. This involves in most cases interconnecting masks that are used to devise the circuit function desired by the customer. Silicon plates with an all purpose gate matrix are produced up to the interconnection level and can be kept at this phase in storage, after which a customer's specific demands can be met very expediently. All purpose logic fields containing 200 logic gates on a chip and an all purpose chip to be expanded to 1,000 logic gates are discussed. The technology facilitates the devising of fast gates with a delay of approximately 5 ns and power dissipation of 1 mW. In assembly it will be possible to make use of the entire assortment of the currently used casings with 16, 18, 20, 24, 28 and 40 outlets. In addition to the development of the mentioned technology, a general methodology for design of the mentioned gate fields is currently under way.

  11. Sliding contacts on printed circuit boards and wear behavior

    OpenAIRE

    Le Solleu, J.-P.

    2010-01-01

    Abstract Automotive suppliers use since decades printed circuit boards (PCB) gold plating pads, as direct contact interface for low current sliding contacts. Several gold plating processes are available on the market, providing various wear behaviour. Some specific galvanic hard gold (AuCo or AuNi). plating was developed on PCB's. This specific plating generates extra costs due to the material quantity and also the process complexity. In a cost driven indust...

  12. Analog and VLSI circuits

    CERN Document Server

    Chen, Wai-Kai

    2009-01-01

    Featuring hundreds of illustrations and references, this book provides the information on analog and VLSI circuits. It focuses on analog integrated circuits, presenting the knowledge on monolithic device models, analog circuit cells, high performance analog circuits, RF communication circuits, and PLL circuits.

  13. 重建钢板上置和前置治疗老年锁骨中段骨折的疗效分析%Superior versus anterior reconstruction plate internal fixation for middle clavicular fractures in old patients: a comparative study

    Institute of Scientific and Technical Information of China (English)

    卢旻鹏; 王群波; 赵波; 何超; 焦春艳; 饶小华; 张铭华

    2011-01-01

    Objective To compare the effect of anterior and superior reconstruction plate internal fixation in treatment of middle clavicular fractures in the old patients.Methods Thirty-nine old patients with middle clavicular fractures received anterior and superior reconstruction plate internal fixation treatment,respectively.There were 19 males and 20 females at average age of 66.7 years.The operation time,intraoperative blood loss and healing time were observed and compared in two groups.According to the Constant scoring system,shoulder functional evaluation was made at half a year after operation and the latest follow-up.Results All the patients were followed up for 10-32 months (average 18.7 months).Of the two groups,there was no statistical significance in aspects of healing time and Constant score at half a year after operation and the latest follow-up ( P >0.05 ).The complication of superior reconstruction plate internal fixation group was significant higher than that of anterior reconstruction plate internal fixation group,while the anterior reconstruction plate internal fixation group had shorter operation time and less intraoperative blood loss in comparison with the superior reconstruction plate internal fixation group ( P < 0.05).Conclusion As for the middle clavicular fractures in the old patients,both anterior and superior reconstruction plate internal fixation can obtain satisfactory curative effect.With shorter operation time,less intraoperative bleeding and less complications,anterior reconstruction plate internal fixation is a much reliable treatment for middle clavicle fractures in the old patients and deserves wider application.%目的 比较重建钢板上置和前置治疗老年锁骨中段骨折的疗效.方法 分别用重建钢板上置法、重建钢板前置法治疗锁骨中段骨折39例,其中男19例,女20例;平均年龄66.7岁.记录并比较两组手术时间、术中出血量、骨折愈合时间;术后半年

  14. Circuit Connectors

    Science.gov (United States)

    1979-01-01

    The U-shaped wire devices in the upper photo are Digi-Klipsm; aids to compact packaging of electrical and electronic devices. They serve as connectors linking the circuitry of one circuit board with another in multi-board systems. Digi-Klips were originally developed for Goddard Space Flight Center to meet a need for lightweight, reliable connectors to replace hand-wired connections formerly used in spacecraft. They are made of beryllium copper wire, noted for its excellent conductivity and its spring-like properties, which assure solid electrical contact over a long period of time.

  15. TIME CALIBRATED OSCILLOSCOPE SWEEP CIRCUIT

    Science.gov (United States)

    Smith, V.L.; Carstensen, H.K.

    1959-11-24

    An improved time calibrated sweep circuit is presented, which extends the range of usefulness of conventional oscilloscopes as utilized for time calibrated display applications in accordance with U. S. Patent No. 2,832,002. Principal novelty resides in the provision of a pair of separate signal paths, each of which is phase and amplitude adjustable, to connect a high-frequency calibration oscillator to the output of a sawtooth generator also connected to the respective horizontal deflection plates of an oscilloscope cathode ray tube. The amplitude and phase of the calibration oscillator signals in the two signal paths are adjusted to balance out feedthrough currents capacitively coupled at high frequencies of the calibration oscillator from each horizontal deflection plate to the vertical plates of the cathode ray tube.

  16. LOGIC CIRCUIT

    Science.gov (United States)

    Strong, G.H.; Faught, M.L.

    1963-12-24

    A device for safety rod counting in a nuclear reactor is described. A Wheatstone bridge circuit is adapted to prevent de-energizing the hopper coils of a ball backup system if safety rods, sufficient in total control effect, properly enter the reactor core to effect shut down. A plurality of resistances form one arm of the bridge, each resistance being associated with a particular safety rod and weighted in value according to the control effect of the particular safety rod. Switching means are used to switch each of the resistances in and out of the bridge circuit responsive to the presence of a particular safety rod in its effective position in the reactor core and responsive to the attainment of a predetermined velocity by a particular safety rod enroute to its effective position. The bridge is unbalanced in one direction during normal reactor operation prior to the generation of a scram signal and the switching means and resistances are adapted to unbalance the bridge in the opposite direction if the safety rods produce a predetermined amount of control effect in response to the scram signal. The bridge unbalance reversal is then utilized to prevent the actuation of the ball backup system, or, conversely, a failure of the safety rods to produce the predetermined effect produces no unbalance reversal and the ball backup system is actuated. (AEC)

  17. Collective of mechatronics circuit

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1987-02-15

    This book is composed of three parts, which deals with mechatronics system about sensor, circuit and motor. The contents of the first part are photo sensor of collector for output, locating detection circuit with photo interrupts, photo sensor circuit with CdS cell and lamp, interface circuit with logic and LED and temperature sensor circuit. The second part deals with oscillation circuit with crystal, C-R oscillation circuit, F-V converter, timer circuit, stability power circuit, DC amp and DC-DC converter. The last part is comprised of bridge server circuit, deformation bridge server, controlling circuit of DC motor, controlling circuit with IC for PLL and driver circuit of stepping motor and driver circuit of Brushless.

  18. Individualized reconstruction plate for treatment of calcaneal fractures via tarsal sinus incision%个体化重建钢板在经跗骨窦切口治疗跟骨骨折中的临床应用

    Institute of Scientific and Technical Information of China (English)

    吴勐; 郭永明; 张朝; 刘重; 石宇; 杨亚龙; 郑文; 魏媛媛

    2015-01-01

    Objective To investigate the clinical efficacy of individualized reconstruction plate in the treatment of calcaneal fractures through the tarsal sinus incision.Methods From May 2010 to September 2012,we treated 46 cases of calcaneal fracture (51 feet) involving talocalcaneal joint.They were 35 males and 11 females,17 to 65 years of age (average,35 years).The injury affected the left foot in 24 cases,the right foot in 17,and both feet in 5.By the Sander's classification,30 feet were type Ⅱ and 21 type 11Ⅲ.The fractures were reduced through the tarsal sinus incision before internal fixation with individualized reconstruction according to the morphology of fracture.When necessary,fixation with hollow screws was added.The B(o)hler and Gissane angles were compared between preoperation and postoperation.The clinical efficacy was evaluated according to the American Orthopaedic Foot and Ankle Society (AOFAS) system.Results The patients were followed up for 8 to 14 months (average,12 months).No such complications as incision infection,skin necrosis,plate loosening or exposure occurred in this group.There were significant differences in the B(o)hler and Gissane angles between preoperation and postoperation [(31.70° ± 5.50° and 122.10° ± 6.79° at 3 days postoperation) and (30.95° ± 3.47° and 122.49° ± 4.83° at 6 months postoperation) versus (6.14° ± 1.58° and 91.63° ± 4.76° at preoperation)] (P < 0.05),but no significant difference in the B(o)hler and Gissane angles between 3 days postoperation and 6 months postoperation (P > 0.05).All the patients obtained bony union at 6 months postoperation.According to the AOFAS scores,38 feet were excellent,9 feet good and 4 feet fair,giving an excellent to good rate of 92.2%.Conclusion In the treatment of intra-articular calcaneal fractures through the tarsal sinus incision,application of individualized reconstruction plate can lead to fine fracture reduction,rigid internal fixation,early exercise

  19. Commutation circuit for an HVDC circuit breaker

    Science.gov (United States)

    Premerlani, William J.

    1981-01-01

    A commutation circuit for a high voltage DC circuit breaker incorporates a resistor capacitor combination and a charging circuit connected to the main breaker, such that a commutating capacitor is discharged in opposition to the load current to force the current in an arc after breaker opening to zero to facilitate arc interruption. In a particular embodiment, a normally open commutating circuit is connected across the contacts of a main DC circuit breaker to absorb the inductive system energy trapped by breaker opening and to limit recovery voltages to a level tolerable by the commutating circuit components.

  20. ACL reconstruction

    Science.gov (United States)

    ... this page: //medlineplus.gov/ency/article/007208.htm ACL reconstruction To use the sharing features on this page, please enable JavaScript. ACL reconstruction is surgery to reconstruct the ligament in ...

  1. Tailoring the Electromagnetic Near Field with Patterned Surfaces: Near-Field Plates

    Science.gov (United States)

    2014-12-10

    near-field plates possible. A linear near-field plate is shown in Fig. 1, which can create a subwavelength line (1D) focus when excited by an...concentric annular slots on a circular grounded dielectric slab. The plate is excited through a coaxial cable and its rim is short circuited. The slots are...standard printed circuit board technology. The plates consist of concentric annular slots on a circular grounded dielectric slab excited through a coaxial

  2. Hierarchical self-organization of tectonic plates

    CERN Document Server

    Morra, Gabriele; Müller, R Dietmar

    2010-01-01

    The Earth's surface is subdivided into eight large tectonic plates and many smaller ones. We reconstruct the plate tessellation history and demonstrate that both large and small plates display two distinct hierarchical patterns, described by different power-law size-relationships. While small plates display little organisational change through time, the structure of the large plates oscillate between minimum and maximum hierarchical tessellations. The organization of large plates rapidly changes from a weak hierarchy at 120-100 million years ago (Ma) towards a strong hierarchy, which peaked at 65-50, Ma subsequently relaxing back towards a minimum hierarchical structure. We suggest that this fluctuation reflects an alternation between top and bottom driven plate tectonics, revealing a previously undiscovered tectonic cyclicity at a timescale of 100 million years.

  3. Analog circuit design designing dynamic circuit response

    CERN Document Server

    Feucht, Dennis

    2010-01-01

    This second volume, Designing Dynamic Circuit Response builds upon the first volume Designing Amplifier Circuits by extending coverage to include reactances and their time- and frequency-related behavioral consequences.

  4. Analog circuit design designing waveform processing circuits

    CERN Document Server

    Feucht, Dennis

    2010-01-01

    The fourth volume in the set Designing Waveform-Processing Circuits builds on the previous 3 volumes and presents a variety of analog non-amplifier circuits, including voltage references, current sources, filters, hysteresis switches and oscilloscope trigger and sweep circuitry, function generation, absolute-value circuits, and peak detectors.

  5. Rehabilitation after reconstruction of anterior cruciate ligament with quadrupled stranded semitendinosus tendon and suture plate%采用四股半腱肌肌腱和缝线钢板重建前十字韧带后的康复训练

    Institute of Scientific and Technical Information of China (English)

    赵金忠; 蒋垚; 沈灏; 邵俊杰

    2002-01-01

    Objective To introduce the rehabilitation methods after reconstruction of anterior cruciate ligament(ACL) with quadrupled stranded semitendinosus tendon and suture plate.Methods 51 cases of ACL ruptures were reconstructed with quadrupled stranded semitendinosus tendon and suture plate.The patients were instructed postoperationally for rehabilitation for more than 1 year.Results The range of motion of the injured knee were regained in all cases 3 months after operation.The quadriceps/hamstrings peak torque ratio reached approximately 80% of the uninjured leg 1 year after opeation.KT 1 000 examination showed that the anterior laxity of the affected knee was greater than the healthy knee in 11.76% and in 10.41% of the patients respectively ,6 and 12 months after operation,but the patients differences were less than 4 mm.In the other patients,the anterior laxity of the affected knee was equal or less than the healthy knee 1 year after opation,95.83% patients regain normal gaits,and the total knee score were (97.8± 1.2) according to Lysholm score scale.Conclusion This rehabilitation procedure was practical and effective for functional restoration of the injured knee as well as the injured leg in patients undergoing ACL reconstruction.

  6. A simple method for medial canthal reconstruction

    NARCIS (Netherlands)

    Wittkampf, ARM; Mourits, MP

    2001-01-01

    A simple method for medical canthal wiring reconstruction with the help of a homolaterally fixed osteosynthesis plate and a metal wire is presented. This avoids transnasal wiring and gives superior control when correcting the position of the lacerated Omedial canthus.

  7. Passively Shunted Piezoelectric Damping of Centrifugally-Loaded Plates

    Science.gov (United States)

    Duffy, Kirsten P.; Provenza, Andrew J.; Trudell, Jeffrey J.; Min, James B.

    2009-01-01

    Researchers at NASA Glenn Research Center have been investigating shunted piezoelectric circuits as potential damping treatments for turbomachinery rotor blades. This effort seeks to determine the effects of centrifugal loading on passively-shunted piezoelectric - damped plates. Passive shunt circuit parameters are optimized for the plate's third bending mode. Tests are performed both non-spinning and in the Dynamic Spin Facility to verify the analysis, and to determine the effectiveness of the damping under centrifugal loading. Results show that a resistive shunt circuit will reduce resonant vibration for this configuration. However, a tuned shunt circuit will be required to achieve the desired damping level. The analysis and testing address several issues with passive shunt circuit implementation in a rotating system, including piezoelectric material integrity under centrifugal loading, shunt circuit implementation, and tip mode damping.

  8. Solid-state circuits

    CERN Document Server

    Pridham, G J

    2013-01-01

    Solid-State Circuits provides an introduction to the theory and practice underlying solid-state circuits, laying particular emphasis on field effect transistors and integrated circuits. Topics range from construction and characteristics of semiconductor devices to rectification and power supplies, low-frequency amplifiers, sine- and square-wave oscillators, and high-frequency effects and circuits. Black-box equivalent circuits of bipolar transistors, physical equivalent circuits of bipolar transistors, and equivalent circuits of field effect transistors are also covered. This volume is divided

  9. Simple Autonomous Chaotic Circuits

    Science.gov (United States)

    Piper, Jessica; Sprott, J.

    2010-03-01

    Over the last several decades, numerous electronic circuits exhibiting chaos have been proposed. Non-autonomous circuits with as few as two components have been developed. However, the operation of such circuits relies on the non-ideal behavior of the devices used, and therefore the circuit equations can be quite complex. In this paper, we present two simple autonomous chaotic circuits using only opamps and linear passive components. The circuits each use one opamp as a comparator, to provide a signum nonlinearity. The chaotic behavior is robust, and independent of nonlinearities in the passive components. Moreover, the circuit equations are among the algebraically simplest chaotic systems yet constructed.

  10. Circuit analysis for dummies

    CERN Document Server

    Santiago, John

    2013-01-01

    Circuits overloaded from electric circuit analysis? Many universities require that students pursuing a degree in electrical or computer engineering take an Electric Circuit Analysis course to determine who will ""make the cut"" and continue in the degree program. Circuit Analysis For Dummies will help these students to better understand electric circuit analysis by presenting the information in an effective and straightforward manner. Circuit Analysis For Dummies gives you clear-cut information about the topics covered in an electric circuit analysis courses to help

  11. Current limiter circuit system

    Energy Technology Data Exchange (ETDEWEB)

    Witcher, Joseph Brandon; Bredemann, Michael V.

    2017-09-05

    An apparatus comprising a steady state sensing circuit, a switching circuit, and a detection circuit. The steady state sensing circuit is connected to a first, a second and a third node. The first node is connected to a first device, the second node is connected to a second device, and the steady state sensing circuit causes a scaled current to flow at the third node. The scaled current is proportional to a voltage difference between the first and second node. The switching circuit limits an amount of current that flows between the first and second device. The detection circuit is connected to the third node and the switching circuit. The detection circuit monitors the scaled current at the third node and controls the switching circuit to limit the amount of the current that flows between the first and second device when the scaled current is greater than a desired level.

  12. Solenoid-Simulation Circuit

    Science.gov (United States)

    Simon, R. A.

    1986-01-01

    Electrical properties of solenoids imitated for tests of control circuits. Simulation circuit imitates voltage and current responses of two engine-controlling solenoids. Used in tests of programs of digital engine-control circuits, also provides electronic interface with circuits imitating electrical properties of pressure sensors and linear variable-differential transformers. Produces voltages, currents, delays, and discrete turnon and turnoff signals representing operation of solenoid in engine-control relay. Many such circuits used simulating overall engine circuitry.

  13. Create Your Plate

    Medline Plus

    Full Text Available ... A A A Listen En Español Create Your Plate Create Your Plate is a simple and effective ... and that your options are endless. Create Your Plate! Click on the plate sections below to add ...

  14. A computational study of gabor zone plate gamma ray holography

    CERN Document Server

    Jackson, C E

    2000-01-01

    Gamma ray zone plate holography is a new technique with applications to Nuclear Medicine. Unlike other tomographic techniques, three-dimensional images can be reconstructed from just one projection. The history of zone plate holography is reviewed, and the differences between this technique and conventional holography are outlined. Sources of error in the recorded hologram are reviewed and methods for the assessment of image quality are given. Three image reconstruction techniques are described and compared. These techniques are convolution, deconvolution and the CLEAN algorithm. Simulated diffraction is the main image reconstruction method which has previously been used to reconstruct images from zone plate holograms. This method is a form of convolution reconstruction. Several variations on this technique are introduced and compared. Matched filtering is also investigated and compared with the simulated diffraction based methods. An approximate Fourier Wiener filter is used to reconstruct the images by deco...

  15. Plate tectonics in the late Paleozoic

    Directory of Open Access Journals (Sweden)

    Mathew Domeier

    2014-05-01

    Full Text Available As the chronicle of plate motions through time, paleogeography is fundamental to our understanding of plate tectonics and its role in shaping the geology of the present-day. To properly appreciate the history of tectonics—and its influence on the deep Earth and climate—it is imperative to seek an accurate and global model of paleogeography. However, owing to the incessant loss of oceanic lithosphere through subduction, the paleogeographic reconstruction of ‘full-plates’ (including oceanic lithosphere becomes increasingly challenging with age. Prior to 150 Ma ∼60% of the lithosphere is missing and reconstructions are developed without explicit regard for oceanic lithosphere or plate tectonic principles; in effect, reflecting the earlier mobilistic paradigm of continental drift. Although these ‘continental’ reconstructions have been immensely useful, the next-generation of mantle models requires global plate kinematic descriptions with full-plate reconstructions. Moreover, in disregarding (or only loosely applying plate tectonic rules, continental reconstructions fail to take advantage of a wealth of additional information in the form of practical constraints. Following a series of new developments, both in geodynamic theory and analytical tools, it is now feasible to construct full-plate models that lend themselves to testing by the wider Earth-science community. Such a model is presented here for the late Paleozoic (410–250 Ma together with a review of the underlying data. Although we expect this model to be particularly useful for numerical mantle modeling, we hope that it will also serve as a general framework for understanding late Paleozoic tectonics, one on which future improvements can be built and further tested.

  16. Plate tectonics in the late Paleozoic

    Institute of Scientific and Technical Information of China (English)

    Mathew Domeier; Trond H. Torsvik

    2014-01-01

    As the chronicle of plate motions through time, paleogeography is fundamental to our understanding of plate tectonics and its role in shaping the geology of the present-day. To properly appreciate the history of tectonicsdand its influence on the deep Earth and climatedit is imperative to seek an accurate and global model of paleogeography. However, owing to the incessant loss of oceanic lithosphere through subduction, the paleogeographic reconstruction of‘full-plates’ (including oceanic lithosphere) becomes increasingly challenging with age. Prior to 150 Ma w60% of the lithosphere is missing and re-constructions are developed without explicit regard for oceanic lithosphere or plate tectonic principles;in effect, reflecting the earlier mobilistic paradigm of continental drift. Although these ‘continental’ re-constructions have been immensely useful, the next-generation of mantle models requires global plate kinematic descriptions with full-plate reconstructions. Moreover, in disregarding (or only loosely applying) plate tectonic rules, continental reconstructions fail to take advantage of a wealth of additional information in the form of practical constraints. Following a series of new developments, both in geo-dynamic theory and analytical tools, it is now feasible to construct full-plate models that lend themselves to testing by the wider Earth-science community. Such a model is presented here for the late Paleozoic (410e250 Ma) together with a review of the underlying data. Although we expect this model to be particularly useful for numerical mantle modeling, we hope that it will also serve as a general framework for understanding late Paleozoic tectonics, one on which future improvements can be built and further tested.

  17. Hidden circuits and argumentation

    Science.gov (United States)

    Leinonen, Risto; Kesonen, Mikko H. P.; Hirvonen, Pekka E.

    2016-11-01

    Despite the relevance of DC circuits in everyday life and schools, they have been shown to cause numerous learning difficulties at various school levels. In the course of this article, we present a flexible method for teaching DC circuits at lower secondary level. The method is labelled as hidden circuits, and the essential idea underlying hidden circuits is in hiding the actual wiring of DC circuits, but to make their behaviour evident for pupils. Pupils are expected to find out the wiring of the circuit which should enhance their learning of DC circuits. We present two possible ways to utilise hidden circuits in a classroom. First, they can be used to test and enhance pupils’ conceptual understanding when pupils are expected to find out which one of the offered circuit diagram options corresponds to the actual circuit shown. This method aims to get pupils to evaluate the circuits holistically rather than locally, and as a part of that aim this method highlights any learning difficulties of pupils. Second, hidden circuits can be used to enhance pupils’ argumentation skills with the aid of argumentation sheet that illustrates the main elements of an argument. Based on the findings from our co-operating teachers and our own experiences, hidden circuits offer a flexible and motivating way to supplement teaching of DC circuits.

  18. Breast Reconstruction

    Science.gov (United States)

    ... rebuild the shape of the breast. Instead of breast reconstruction, you could choose to wear a breast form ... one woman may not be right for another. Breast reconstruction may be done at the same time as ...

  19. Pulse plating

    CERN Document Server

    Hansal, Wolfgang E G; Green, Todd; Leisner, Peter; Reichenbach, Andreas

    2012-01-01

    The electrodeposition of metals using pulsed current has achieved practical importance in recent years. Although it has long been known that changes in potential, with or without polarity reversal, can significantly affect the deposition process, the practical application of this has been slow to be adopted. This can largely be explained in terms of the complex relationship between the current regime and its effect on the electrodeposition process. In order to harness these effects, an understanding of the anodic and cathodic electrochemical processes is necessary, together with the effects of polarity reversal and the rate of such reversals. In this new monograph, the basics of metal electrodeposition from solution are laid out in great detail in seven distinct chapters. With this knowledge, the reader is able to predict how a given pulse train profile can be adopted to achieve a desired outcome. Equally important is the choice of a suitable rectifier and the ancillary control circuits to enable pulse platin...

  20. Late reconstruction of condylar neck and head fractures.

    Science.gov (United States)

    Davis, Ben

    2013-11-01

    Condyle fractures are a common injury, but only a few of these injuries require immediate or late reconstruction. The complications that most frequently necessitate condylar reconstruction include proximal segment degeneration, malunion, and ankylosis. Costochondral grafts and total joint prostheses, both stock and custom, remain the most common methods of reconstruction. Reconstruction plates with condylar extensions should only be used temporarily as an unacceptable number cause serious complications. Distraction osteogenesis may have an occasional role in reconstructing the posttraumatic condyle.

  1. Intuitive analog circuit design

    CERN Document Server

    Thompson, Marc

    2013-01-01

    Intuitive Analog Circuit Design outlines ways of thinking about analog circuits and systems that let you develop a feel for what a good, working analog circuit design should be. This book reflects author Marc Thompson's 30 years of experience designing analog and power electronics circuits and teaching graduate-level analog circuit design, and is the ideal reference for anyone who needs a straightforward introduction to the subject. In this book, Dr. Thompson describes intuitive and ""back-of-the-envelope"" techniques for designing and analyzing analog circuits, including transistor amplifi

  2. The circuit designer's companion

    CERN Document Server

    Williams, Tim

    2013-01-01

    The Circuit Designer's Companion covers the theoretical aspects and practices in analogue and digital circuit design. Electronic circuit design involves designing a circuit that will fulfill its specified function and designing the same circuit so that every production model of it will fulfill its specified function, and no other undesired and unspecified function.This book is composed of nine chapters and starts with a review of the concept of grounding, wiring, and printed circuits. The subsequent chapters deal with the passive and active components of circuitry design. These topics are foll

  3. Electrical Circuits and Water Analogies

    Science.gov (United States)

    Smith, Frederick A.; Wilson, Jerry D.

    1974-01-01

    Briefly describes water analogies for electrical circuits and presents plans for the construction of apparatus to demonstrate these analogies. Demonstrations include series circuits, parallel circuits, and capacitors. (GS)

  4. Circuits on Cylinders

    DEFF Research Database (Denmark)

    Hansen, Kristoffer Arnsfelt; Miltersen, Peter Bro; Vinay, V

    2006-01-01

    We consider the computational power of constant width polynomial size cylindrical circuits and nondeterministic branching programs. We show that every function computed by a Pi2 o MOD o AC0 circuit can also be computed by a constant width polynomial size cylindrical nondeterministic branching...... program (or cylindrical circuit) and that every function computed by a constant width polynomial size cylindrical circuit belongs to ACC0....

  5. Electric circuits essentials

    CERN Document Server

    REA, Editors of

    2012-01-01

    REA's Essentials provide quick and easy access to critical information in a variety of different fields, ranging from the most basic to the most advanced. As its name implies, these concise, comprehensive study guides summarize the essentials of the field covered. Essentials are helpful when preparing for exams, doing homework and will remain a lasting reference source for students, teachers, and professionals. Electric Circuits I includes units, notation, resistive circuits, experimental laws, transient circuits, network theorems, techniques of circuit analysis, sinusoidal analysis, polyph

  6. Research on dynamic model of printed circuit board based on finite element method

    Science.gov (United States)

    Wei, Hui; Xu, Liangjun

    2017-08-01

    The vibration characteristics of printed circuit boards are related to the reliability of electronic components installed on their surface. Finite element software is a powerful tool to analyze the vibration characteristics of printed circuit boards, and the correct establishment of finite element model is very important. In this paper, the dynamic model of anisotropic printed circuit board is established by analyzing the material properties of printed circuit board. The influence of boundary condition and lumped mass on the vibration characteristics of printed circuit board is analyzed. In order to establish a more realistic printed circuit The finite element model of the plate provides the necessary basis.

  7. Piezoelectric drive circuit

    Science.gov (United States)

    Treu, Jr., Charles A.

    1999-08-31

    A piezoelectric motor drive circuit is provided which utilizes the piezoelectric elements as oscillators and a Meacham half-bridge approach to develop feedback from the motor ground circuit to produce a signal to drive amplifiers to power the motor. The circuit automatically compensates for shifts in harmonic frequency of the piezoelectric elements due to pressure and temperature changes.

  8. Signal sampling circuit

    NARCIS (Netherlands)

    Louwsma, S.M.; Vertregt, Maarten

    2010-01-01

    A sampling circuit for sampling a signal is disclosed. The sampling circuit comprises a plurality of sampling channels adapted to sample the signal in time-multiplexed fashion, each sampling channel comprising a respective track-and-hold circuit connected to a respective analogue to digital converte

  9. Signal sampling circuit

    NARCIS (Netherlands)

    Louwsma, S.M.; Vertregt, Maarten

    2011-01-01

    A sampling circuit for sampling a signal is disclosed. The sampling circuit comprises a plurality of sampling channels adapted to sample the signal in time-multiplexed fashion, each sampling channel comprising a respective track-and-hold circuit connected to a respective analogue to digital converte

  10. Load testing circuit

    DEFF Research Database (Denmark)

    2009-01-01

    A load testing circuit a circuit tests the load impedance of a load connected to an amplifier. The load impedance includes a first terminal and a second terminal, the load testing circuit comprising a signal generator providing a test signal of a defined bandwidth to the first terminal of the load...

  11. Short-circuit logic

    NARCIS (Netherlands)

    Bergstra, J.A.; Ponse, A.

    2010-01-01

    Short-circuit evaluation denotes the semantics of propositional connectives in which the second argument is only evaluated if the first argument does not suffice to determine the value of the expression. In programming, short-circuit evaluation is widely used. A short-circuit logic is a variant of p

  12. Signal sampling circuit

    NARCIS (Netherlands)

    Louwsma, Simon Minze; Vertregt, Maarten

    2011-01-01

    A sampling circuit for sampling a signal is disclosed. The sampling circuit comprises a plurality of sampling channels adapted to sample the signal in time-multiplexed fashion, each sampling channel comprising a respective track-and-hold circuit connected to a respective analogue to digital converte

  13. Signal sampling circuit

    NARCIS (Netherlands)

    Louwsma, Simon Minze; Vertregt, Maarten

    2010-01-01

    A sampling circuit for sampling a signal is disclosed. The sampling circuit comprises a plurality of sampling channels adapted to sample the signal in time-multiplexed fashion, each sampling channel comprising a respective track-and-hold circuit connected to a respective analogue to digital converte

  14. Diode-quad bridge circuit means

    Science.gov (United States)

    Harrison, D. R.; Dimeff, J. (Inventor)

    1975-01-01

    A transducer and frequency discriminator circuit is described including a four-terminal circulating diode bridge, a first pair of capacitors connected in series across two terminals of the bridge, and a second pair of capacitors, or other impedance elements, connected in series across the other two terminals of the bridge. A source of balanced alternating electrical energy for energizing the circuit is coupled between the commonly connected plates of the first pair of capacitors and the commonly connected plates of the second pair of capacitors. Due to the operation of the diode bridge, the sum of the resultant charges developed on the first pair of capacitors is proportional to the relationship between the respective capacitors of the second pair, and consequently, an output voltage taken across the first pair of capacitors will be proportional to that relationship.

  15. Reversible Logic Circuit Synthesis

    CERN Document Server

    Shende, V V; Markov, I L; Prasad, A K; Hayes, John P.; Markov, Igor L.; Prasad, Aditya K.; Shende, Vivek V.

    2002-01-01

    Reversible, or information-lossless, circuits have applications in digital signal processing, communication, computer graphics and cryptography. They are also a fundamental requirement for quantum computation. We investigate the synthesis of reversible circuits that employ a minimum number of gates and contain no redundant input-output line-pairs (temporary storage channels). We propose new constructions for reversible circuits composed of NOT, Controlled-NOT, and TOFFOLI gates (the CNT gate library) based on permutation theory. A new algorithm is given to synthesize optimal reversible circuits using an arbitrary gate library. We also describe much faster heuristic algorithms. We also pursue applications of the proposed techniques to the synthesis of quantum circuits.

  16. Plate reconstruction and tubularization urethroplasty in the repair of complicated hypospadias%尿道板重建卷管尿道成形术在复杂尿道下裂矫治中的应用

    Institute of Scientific and Technical Information of China (English)

    唐耘熳; 陈绍基; 毛宇; 王学军; 刘茂

    2015-01-01

    Objective To evaluate the efficacy of plate reconstruction and tubularization urethroplasty (PRTU) in the repair of complicated hypospadias.Methods From September 2010 to July 2014,145 patients with hypospadias were repaired with PRTU technique.The average age was 52 (10-86) months.Among them,primary cases included proximal shaft (n =1),scrotal (n =76),perineal (n =56) and type Ⅳ chordee without hypospadias (n =2).And secondary cases included post-stage-Ⅰ (n =9) and urethral dehiscence (n =1).PRTU was performed alone,or plus island tube or buccal mucosa,as single-stage or staged repair.Results A total of 84 patients were repaired in single-stage including PRTU alone (n =65) and plus island tube (n =19).Staged repair was performed with PRTU alone (n =56),plus island tube (n =1) and plus buccal mucosa (n =4).During a mean follow-up period of 19 (3-47) months,the complications during single-stage PRTU repair occurred at a rate of 16.9% (11/65),including fistula 4.6% (3/65),stricture 3.1% (2/65),glans dehiscence 9.2%(6/65) and urethral diverticulum 1.5% (1/65) ; single-stage plus flap 10.5% (2/19)[fistula 5.0%(1/19) and urethral diverticulum 5.0%(1/19)]; stage Ⅰ 4.9%(3/61)(fistula 3/ 61) and in 6/36 patients stage Ⅱ 16.7% [fistula 8.3% (3/36),stricture 2.8% (1/36),glans dehiscence 5.6%(2/36) and urehral diverticulum 2.8%(1/36)].Conclusions PRTU may be indicated in the repair of primary or redo hypospadias with poor quality of local tissue.It can be used alone or plus island tube or free graft during single-stage or staged repairs.%目的 探讨尿道板重建卷管尿道成形术(PRTU)在复杂尿道下裂矫治中的应用.方法 回顾性分析2010年9月至2014年7月应用PRTU方法矫治145例尿道下裂的病例资料.本组年龄10个月到37岁2个月,平均4岁4个月.其中初治病例135例(阴茎近段型1例,阴囊型76例,会阴型56例,无尿道下裂阴茎弯曲畸形Ⅳ型2例),再手术10例(9例一期手术后,1

  17. Exact Threshold Circuits

    DEFF Research Database (Denmark)

    Hansen, Kristoffer Arnsfelt; Podolskii, Vladimir V.

    2010-01-01

    We initiate a systematic study of constant depth Boolean circuits built using exact threshold gates. We consider both unweighted and weighted exact threshold gates and introduce corresponding circuit classes. We next show that this gives a hierarchy of classes that seamlessly interleave with the ......We initiate a systematic study of constant depth Boolean circuits built using exact threshold gates. We consider both unweighted and weighted exact threshold gates and introduce corresponding circuit classes. We next show that this gives a hierarchy of classes that seamlessly interleave...... with the well-studied corresponding hierarchies defined using ordinary threshold gates. A major open problem in Boolean circuit complexity is to provide an explicit super-polynomial lower bound for depth two threshold circuits. We identify the class of depth two exact threshold circuits as a natural subclass...

  18. Feedback in analog circuits

    CERN Document Server

    Ochoa, Agustin

    2016-01-01

    This book describes a consistent and direct methodology to the analysis and design of analog circuits with particular application to circuits containing feedback. The analysis and design of circuits containing feedback is generally presented by either following a series of examples where each circuit is simplified through the use of insight or experience (someone else’s), or a complete nodal-matrix analysis generating lots of algebra. Neither of these approaches leads to gaining insight into the design process easily. The author develops a systematic approach to circuit analysis, the Driving Point Impedance and Signal Flow Graphs (DPI/SFG) method that does not require a-priori insight to the circuit being considered and results in factored analysis supporting the design function. This approach enables designers to account fully for loading and the bi-directional nature of elements both in the feedback path and in the amplifier itself, properties many times assumed negligible and ignored. Feedback circuits a...

  19. Biomechanical Study of Acetabunlum Transverse and Posterior Wall Fractures Treated by Internal Fixation with Locking Reconstruction Plate%锁定重建接骨板治疗髋臼横行伴后壁骨折的生物力学研究

    Institute of Scientific and Technical Information of China (English)

    付久洋; 吴啸波

    2015-01-01

    Objective To evaluate the stability of 3 different internal fixation methods for transverse and posterior wall fractures of the acetabulum. Methods Seighteen acetabula of 9 whole pelvises were divided into 3 groups randomly. Models of transverse and posterior wall fracturesof acetabulum were established and then fixed with one of following three internal fixation methods:(Group A)posterior column locking reconstruction plate group,(Group B)posterior column common reconstruction plate withposterior wall 2 lag screwsgroup ,(Group C)anterior column lag screw and posterior column common reconstruction plate with posterior wall2 lag screws group. biomechanical tests are conducted in a single leg stance tomeasurethe maximal loads in the three groups and the displacements of the posterior wall fractures when the stress were loaded to 2 200 N on the three groups. Results The maximal loads in Groups A,B,C were as follows:(2243. 74 ± 116. 36)N,(2769. 05 ± 131. 42) N,(2832. 87 ± 137. 93)N. When the stress was loaded to 2 200 N on the three groups,the displacements of the posterior wall fractures were as follows:(2. 15 ± 0. 26)mm,(0. 45 ± 0. 05)mm,(0. 53 ± 0. 07)mm. We found there was no significant difference between the Group B and the Group C(P > 0. 05). There was significant difference between Groups B,C and Groups A,(P 0.05)。B、C 两组数据与 A 组比较,差异均有统计学意义(P <0.05,P <0.01)。结论锁定重建接骨板固定髋臼横行伴后壁骨折固定可靠,能够满足患者早期功能锻炼的要求,具有较大临床应用价值。

  20. Predictability in orbital reconstruction: A human cadaver study. Part II: Navigation-assisted orbital reconstruction

    NARCIS (Netherlands)

    Dubois, L.; Schreurs, R.; Jansen, J; Maal, T.J.J.; Essig, H.; Gooris, P.J.; Becking, A.G.

    2015-01-01

    Preformed orbital reconstruction plates are useful for treating orbital defects. However, intraoperative errors can lead to misplaced implants and poor outcomes. Navigation-assisted surgery may help optimize orbital reconstruction. We aimed to explore whether navigation-assisted surgery is more pred

  1. Predictability in orbital reconstruction: a human cadaver study: part II: navigation-assisted orbital reconstruction

    NARCIS (Netherlands)

    Dubois, L.; Schreurs, R.; Jansen, J.; Maal, T.J.J.; Essig, H.; Gooris, P.J.J.; Becking, A.G.

    2015-01-01

    Preformed orbital reconstruction plates are useful for treating orbital defects. However, intraoperative errors can lead to misplaced implants and poor outcomes. Navigation-assisted surgery may help optimize orbital reconstruction. We aimed to explore whether navigation-assisted surgery is more pred

  2. A chain of suprasegmental neuroscillatory circuits: a human brain theory.

    Science.gov (United States)

    Deshmukh, V D

    1988-01-01

    A novel electrophysiological model of human brain electrical activity and functions is proposed. It views the human central nervous system as a chain of three suprasegmental neuroscillatory circuits, namely prosencephalic, mesencephalic, and rhombencephalic. Each circuit consists of a network of periventricular paracrine core neurons, efferent motor plate neurons, and sensory-associative alar plate neurons mediating suprasegmental electroclinical phenomena. The model is based on the exponential analyses of well established human data from the fields of electroencephalography, evoked potentials, wake-sleep spectrum, stages of anesthesia, and a variety of human tremors. This neuroscillatory chain is functionally analogous to the chain of cardiac pacemaker neurons.

  3. Sliding contacts on printed circuit boards and wear behavior

    Science.gov (United States)

    Le Solleu, J.-P.

    2010-04-01

    Automotive suppliers use since decades printed circuit boards (PCB) gold plating pads, as direct contact interface for low current sliding contacts. Several gold plating processes are available on the market, providing various wear behaviour. Some specific galvanic hard gold (AuCo or AuNi). plating was developed on PCB's. This specific plating generates extra costs due to the material quantity and also the process complexity. In a cost driven industry, the challenge is to use a standard low cost PCB for systems requesting high reliability performances. After a brief overview of standard PCB manufacturing processes and especially gold plating processes, the global experimental results of wear behaviour of three different gold plating technologies will be exposed and an explanation of the correlation between surface key parameters and wear out will be provided.

  4. Penile reconstruction

    Institute of Scientific and Technical Information of China (English)

    Giulio Garaffa; Salvatore Sansalone; David J Ralph

    2013-01-01

    During the most recent years,a variety of new techniques of penile reconstruction have been described in the literature.This paper focuses on the most recent advances in male genital reconstruction after trauma,excision of benign and malignant disease,in gender reassignment surgery and aphallia with emphasis on surgical technique,cosmetic and functional outcome.

  5. Towards absolute plate motions constrained by lower-mantle slab remnants

    NARCIS (Netherlands)

    Meer, D.G. van der; Spakman, W.; Hinsbergen, D.J.J. van; Amaru, M.L.; Torsvik, T.H.

    2010-01-01

    Since the first reconstruction of the supercontinent Pangaea, key advances in plate tectonic reconstructions have been made1. Although the movement of tectonic plates since the start of the mid-Cretaceous period (~100 million years (Myr) ago) is relatively well understood1, 2, the longitudinal posit

  6. The curative effect analysis of acetabulum fracture treated with bridge combined fixation sys-tem or reconstruction plate%桥接组合式内固定系统与重建钢板治疗髋臼骨折的疗效比较

    Institute of Scientific and Technical Information of China (English)

    关翔; 宋香全; 王洪炳; 周朝波

    2015-01-01

    Objective To investigate the clinical efficacy of reconstruction plate or bridge combined fixation system in the treatment of acetabulum fractures. Methods Fifty-five patients of acetabulum fractures treated by surgery were selected for a case-control study. Twenty-eight patients was treated by reconstruction plate, while twenty-seven pa-tients was treated by bridge combined fixation system. Operation time, intraoperative blood loss and hospital stay of two groups were observed and compared. Results The time of hospital stay, operative time, amount of bleeding of the group treated by bridge combined fixation system was better than the group treated by reconstruction plate. There are statistically significant difference between the two groups (P<0. 05). For the postoperative hip joint function of the reconstruction plate group,14 cases were excellent,9 good,4 fair, and 1 poor, and the rate of excellence and good results was 23/28. For the bridge combined fixation system group,13 cases were excellent,11 good,2 fair, and 1 poor, and the rate of excellence and good results was 24/27. There are statistically significant difference between the two groups of curative effect ( P<0. 05 ) . Conclusions The bridge combined fixation system has the advantages of less trauma, better functional recovery and less postoperative complications, which can be used as the preferred way for the surgical treatment of acetabulum fracture.%目的:探讨重建钢板与桥接组合式内固定系统治疗髋臼骨折临床疗效。方法手术治疗55例髋臼骨折的患者,分别行重建钢板(28例)和桥接组合式内固定系统(27例)内固定,观察两组的手术时间、术中出血量、住院时间,比较两组疗效。结果桥接组合式内固定系统组的手术时间、术中出血量、住院时间均优于重建钢板组,差异有统计学意义(P<0.05)。术后髋关节功能:重建钢板组优14例,良9例,可4例,差1例,优良率23/28;桥接

  7. Shoulder acromioclavicular joint reconstruction options and outcomes.

    Science.gov (United States)

    Lee, Simon; Bedi, Asheesh

    2016-12-01

    Acromioclavicular joint separations are a common cause of shoulder pain in the young athletic population. In high-grade injuries, acromioclavicular joint reconstruction procedures may be indicated for functional improvement. There is currently no gold standard for the surgical management of these injuries. Multiple reconstructive options exist, including coracoclavicular screws, hook plates, endobutton coracoclavicular fixations, and anatomic ligament reconstructions with tendon grafts. This article aims to review pertinent acromioclavicular joint anatomy and biomechanics, radiographic evaluation, classification system, as well as reconstruction options, outcomes, and complications.

  8. Regenerative feedback resonant circuit

    Science.gov (United States)

    Jones, A. Mark; Kelly, James F.; McCloy, John S.; McMakin, Douglas L.

    2014-09-02

    A regenerative feedback resonant circuit for measuring a transient response in a loop is disclosed. The circuit includes an amplifier for generating a signal in the loop. The circuit further includes a resonator having a resonant cavity and a material located within the cavity. The signal sent into the resonator produces a resonant frequency. A variation of the resonant frequency due to perturbations in electromagnetic properties of the material is measured.

  9. Analog circuit design

    CERN Document Server

    Dobkin, Bob

    2012-01-01

    Analog circuit and system design today is more essential than ever before. With the growth of digital systems, wireless communications, complex industrial and automotive systems, designers are being challenged to develop sophisticated analog solutions. This comprehensive source book of circuit design solutions aids engineers with elegant and practical design techniques that focus on common analog challenges. The book's in-depth application examples provide insight into circuit design and application solutions that you can apply in today's demanding designs. <

  10. Parallelizing quantum circuit synthesis

    OpenAIRE

    Di Matteo, Olivia; Mosca, Michele

    2016-01-01

    Quantum circuit synthesis is the process in which an arbitrary unitary operation is decomposed into a sequence of gates from a universal set, typically one which a quantum computer can implement both efficiently and fault-tolerantly. As physical implementations of quantum computers improve, the need is growing for tools which can effectively synthesize components of the circuits and algorithms they will run. Existing algorithms for exact, multi-qubit circuit synthesis scale exponentially in t...

  11. Analog circuits cookbook

    CERN Document Server

    Hickman, Ian

    2013-01-01

    Analog Circuits Cookbook presents articles about advanced circuit techniques, components and concepts, useful IC for analog signal processing in the audio range, direct digital synthesis, and ingenious video op-amp. The book also includes articles about amplitude measurements on RF signals, linear optical imager, power supplies and devices, and RF circuits and techniques. Professionals and students of electrical engineering will find the book informative and useful.

  12. Electronic devices and circuits

    CERN Document Server

    Pridham, Gordon John

    1968-01-01

    Electronic Devices and Circuits, Volume 1 deals with the design and applications of electronic devices and circuits such as passive components, diodes, triodes and transistors, rectification and power supplies, amplifying circuits, electronic instruments, and oscillators. These topics are supported with introductory network theory and physics. This volume is comprised of nine chapters and begins by explaining the operation of resistive, inductive, and capacitive elements in direct and alternating current circuits. The theory for some of the expressions quoted in later chapters is presented. Th

  13. CMOS circuits manual

    CERN Document Server

    Marston, R M

    1995-01-01

    CMOS Circuits Manual is a user's guide for CMOS. The book emphasizes the practical aspects of CMOS and provides circuits, tables, and graphs to further relate the fundamentals with the applications. The text first discusses the basic principles and characteristics of the CMOS devices. The succeeding chapters detail the types of CMOS IC, including simple inverter, gate and logic ICs and circuits, and complex counters and decoders. The last chapter presents a miscellaneous collection of two dozen useful CMOS circuits. The book will be useful to researchers and professionals who employ CMOS circu

  14. Circuits and filters handbook

    CERN Document Server

    Chen, Wai-Kai

    2003-01-01

    A bestseller in its first edition, The Circuits and Filters Handbook has been thoroughly updated to provide the most current, most comprehensive information available in both the classical and emerging fields of circuits and filters, both analog and digital. This edition contains 29 new chapters, with significant additions in the areas of computer-aided design, circuit simulation, VLSI circuits, design automation, and active and digital filters. It will undoubtedly take its place as the engineer's first choice in looking for solutions to problems encountered in the design, analysis, and behavi

  15. Timergenerator circuits manual

    CERN Document Server

    Marston, R M

    2013-01-01

    Timer/Generator Circuits Manual is an 11-chapter text that deals mainly with waveform generator techniques and circuits. Each chapter starts with an explanation of the basic principles of its subject followed by a wide range of practical circuit designs. This work presents a total of over 300 practical circuits, diagrams, and tables.Chapter 1 outlines the basic principles and the different types of generator. Chapters 2 to 9 deal with a specific type of waveform generator, including sine, square, triangular, sawtooth, and special waveform generators pulse. These chapters also include pulse gen

  16. Security electronics circuits manual

    CERN Document Server

    MARSTON, R M

    1998-01-01

    Security Electronics Circuits Manual is an invaluable guide for engineers and technicians in the security industry. It will also prove to be a useful guide for students and experimenters, as well as providing experienced amateurs and DIY enthusiasts with numerous ideas to protect their homes, businesses and properties.As with all Ray Marston's Circuits Manuals, the style is easy-to-read and non-mathematical, with the emphasis firmly on practical applications, circuits and design ideas. The ICs and other devices used in the practical circuits are modestly priced and readily available ty

  17. MOS integrated circuit design

    CERN Document Server

    Wolfendale, E

    2013-01-01

    MOS Integral Circuit Design aims to help in the design of integrated circuits, especially large-scale ones, using MOS Technology through teaching of techniques, practical applications, and examples. The book covers topics such as design equation and process parameters; MOS static and dynamic circuits; logic design techniques, system partitioning, and layout techniques. Also featured are computer aids such as logic simulation and mask layout, as well as examples on simple MOS design. The text is recommended for electrical engineers who would like to know how to use MOS for integral circuit desi

  18. Printed circuit board industry.

    Science.gov (United States)

    LaDou, Joseph

    2006-05-01

    The printed circuit board is the platform upon which microelectronic components such as semiconductor chips and capacitors are mounted. It provides the electrical interconnections between components and is found in virtually all electronics products. Once considered low technology, the printed circuit board is evolving into a high-technology product. Printed circuit board manufacturing is highly complicated, requiring large equipment investments and over 50 process steps. Many of the high-speed, miniaturized printed circuit boards are now manufactured in cleanrooms with the same health and safety problems posed by other microelectronics manufacturing. Asia produces three-fourths of the world's printed circuit boards. In Asian countries, glycol ethers are the major solvents used in the printed circuit board industry. Large quantities of hazardous chemicals such as formaldehyde, dimethylformamide, and lead are used by the printed circuit board industry. For decades, chemically intensive and often sloppy manufacturing processes exposed tens of thousands of workers to a large number of chemicals that are now known to be reproductive toxicants and carcinogens. The printed circuit board industry has exposed workers to high doses of toxic metals, solvents, acids, and photolithographic chemicals. Only recently has there been any serious effort to diminish the quantity of lead distributed worldwide by the printed circuit board industry. Billions of electronics products have been discarded in every region of the world. This paper summarizes recent regulatory and enforcement efforts.

  19. Improved Zone Plate Coded Imaging Technique by Using Four Special Designed Gabor Zone Plates

    Institute of Scientific and Technical Information of China (English)

    CAO Lei-Feng; SHEN Yu-Ji; ZHENG Zhi-Jian; DING Yong-Kun

    2005-01-01

    @@ Direct-current component, high-order artifacts, and side lobe distortion provide serious drawbacks in the application of Fresnel zone plate coded imaging (ZPCI).The presentation provided here proposes a novel way to resolve all the above-mentioned problems.Four different Gabor zone plates are suggested to substitute the one Fresnel zone plate used in the conventional ZPCI.Perfect reconstruction will be obtained when integrally analysing the four coded images.Primary numerical simulation provided here shows good result.

  20. Treatment of middle-third clavicle fractures using anterior plating with a dynamic compression plate (DCP).

    Science.gov (United States)

    Subramanian, Padmanabhan; Joshi, Meera; Shilston, Sophie; Wallace, Donald; Pearce, Oliver J

    2013-03-01

    Significantly displaced midshaft clavicle fractures can be managed operatively to restore anatomy and allow early mobilization. Several techniques have described using precontoured anatomically designed plates placed on the superior surface of the bone or reconstruction plates contoured by the surgeon placed either superiorly or anteriorly. We describe the use of the dynamic compression plate placed anteriorly on the clavicle in treating these fractures and discuss the relative advantages of this technique. We have a case series of 8 patients over a 2-year period, who were followed up and all went on to successful fracture union.

  1. Processless offset printing plates

    Directory of Open Access Journals (Sweden)

    Sanja Mahović Poljaček

    2015-06-01

    Full Text Available With the implementation of platesetters in the offset printing plate making process, imaging of the printing plate became more stable and ensured increase of the printing plate quality. But as the chemical processing of the printing plates still highly influences the plate making process and the graphic reproduction workflow, development of printing plates that do not require chemical processing for offset printing technique has been one of the top interests in graphic technology in the last few years. The main reason for that came from the user experience, where majority of the problems with plate making process could be connected with the chemical processing of the printing plate. Furthermore, increased environmental standards lead to reducing of the chemicals used in the industrial processes. Considering these facts, different types of offset printing plates have been introduced to the market today. This paper presents some of the processless printing plates.

  2. Ligament reconstruction.

    Science.gov (United States)

    Glickel, Steven Z; Gupta, Salil

    2006-05-01

    Volar ligament reconstruction is an effective technique for treating symptomatic laxity of the CMC joint of the thumb. The laxity may bea manifestation of generalized ligament laxity,post-traumatic, or metabolic (Ehler-Danlos). There construction reduces the shear forces on the joint that contribute to the development and persistence of inflammation. Although there have been only a few reports of the results of volar ligament reconstruction, the use of the procedure to treat Stage I and Stage II disease gives good to excellent results consistently. More advanced stages of disease are best treated by trapeziectomy, with or without ligament reconstruction.

  3. Synchronizing Hyperchaotic Circuits

    DEFF Research Database (Denmark)

    Tamasevicius, Arunas; Cenys, Antanas; Namajunas, Audrius

    1997-01-01

    Regarding possible applications to secure communications the technique of synchronizing hyperchaotic circuits with a single dynamical variable is discussed. Several specific examples including the fourth-order circuits with two positive Lyapunov exponents as well as the oscillator with a delay line...... characterized by multiple positive Lyapunov exponents are reviewd....

  4. Genetic circuit design automation.

    Science.gov (United States)

    Nielsen, Alec A K; Der, Bryan S; Shin, Jonghyeon; Vaidyanathan, Prashant; Paralanov, Vanya; Strychalski, Elizabeth A; Ross, David; Densmore, Douglas; Voigt, Christopher A

    2016-04-01

    Computation can be performed in living cells by DNA-encoded circuits that process sensory information and control biological functions. Their construction is time-intensive, requiring manual part assembly and balancing of regulator expression. We describe a design environment, Cello, in which a user writes Verilog code that is automatically transformed into a DNA sequence. Algorithms build a circuit diagram, assign and connect gates, and simulate performance. Reliable circuit design requires the insulation of gates from genetic context, so that they function identically when used in different circuits. We used Cello to design 60 circuits forEscherichia coli(880,000 base pairs of DNA), for which each DNA sequence was built as predicted by the software with no additional tuning. Of these, 45 circuits performed correctly in every output state (up to 10 regulators and 55 parts), and across all circuits 92% of the output states functioned as predicted. Design automation simplifies the incorporation of genetic circuits into biotechnology projects that require decision-making, control, sensing, or spatial organization.

  5. A Virtual Circuits Lab

    Science.gov (United States)

    Vick, Matthew E.

    2010-01-01

    The University of Colorado's Physics Education Technology (PhET) website offers free, high-quality simulations of many physics experiments that can be used in the classroom. The Circuit Construction Kit, for example, allows students to safely and constructively play with circuit components while learning the mathematics behind many circuit…

  6. Breast Reconstruction

    Science.gov (United States)

    ... senos Preguntas Para el Médico Datos Para la Vida Komen El cuidado de sus senos:Consejos útiles ... can help . Cost Federal law requires most insurance plans cover the cost of breast reconstruction. Learn more ...

  7. Climate Reconstructions

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The NOAA Paleoclimatology Program archives reconstructions of past climatic conditions derived from paleoclimate proxies, in addition to the Program's large holdings...

  8. Justification of equivalent substitution circuits used to optimize the dissipative properties of electroelastic bodies with external electric circuits

    Science.gov (United States)

    Ivanov, A. S.; Matvienko, V. P.; Oshmarin, D. A.; Sevodina, N. V.; Yurlov, M. A.; Yurlova, N. A.

    2016-05-01

    We consider elastoplastic systems which are piecewise homogeneous bodies composed of piezoelectric elements some of which have piezoelectrical properties. Electric series circuits consisting of resistors, capacitors, and inductance coils are applied to piezoelectric elements through the electrode coating on the body surface. The goal of the study is to develop efficient methods of mathematical modelling for determining the parameters of elements of the external electric circuit, which ensure, at prescribed resonance frequencies, the maximum damping properties of electroelastic bodies with external electric circuits. To choose effective circuits for solving the problem posed above, we suggest to pose the problem of natural vibrations of elastic bodies whose elements exhibit piezoeffect and have external electric circuits.As the most efficient approaches for calculating the electric circuit parameters necessary for the maximal damping, we propose some versions of equivalent circuits, which can be used to substitute elastic systems with piezoelectric elements. The most reliable equivalent substitution circuits are justified on the basis of the proposed problem of natural vibrations. Numerical results are obtained for a cantilever plate with a piezoelement connected through the electrode coated surface with a series electric circuit consisting of resistors, capacitors and inductance coils.

  9. 微型钛板塑形内固定整复术治疗眼眶骨折患者的临床疗效%Analysis of clinical efficacy and complications of titanium mini plate internal fixation and reconstructive surgery for patients with orbital fracture

    Institute of Scientific and Technical Information of China (English)

    刘洋; 王彦荣; 胡文静

    2016-01-01

    AIM: To analyze the clinical efficacy and complications of titanium mini plate internal fixation and reconstructive surgery for patients with orbital fracture. METHODS: Fifty - seven cases (60 eyes) with orbital fracture from March 2013 to April 2014 in our hospital were researched. According to the random number table method, the patients were divided into observation group (29 cases with 30 eyes) and control group (28 cases with 30 eyes ). The control group was treated with hydroxyapatite artificial bone plate for internal fixation, and the observation group with titanium mini plate internal fixation and reconstructive surgery. The diplopia grading, grading of ocular movement disorder before and at 1, 3mo after treatment and postoperative complications ( prolapse, dislocation, infection ) were compared between the two groups. RESULTS: In both group, all the 60 eyes were healed without scar formation. The rate of diplopia grading as grade 0 1mo postoperatively of observation group and the control groups were 63% and 40% ( P CONCLUSION: The clinical curative effect of titanium mini plate internal fixation and reconstructive surgery has a good effect for orbital fractures, which can improve the therapeutic effect and reduce the incidence of adverse reactions.%目的:微型钛板塑形内固定整复术治疗眼眶骨折患者的临床疗效及并发症的分析。  方法:选择2013-03/2014-04我院收治的眼眶骨折患者57例60眼,按照随机数表法将患者分为观察组29例30眼和对照组28例30眼。观察组给予微型钛板塑形内固定整复术治疗;对照组患者给予羟基磷灰石复合人工骨板的内固定治疗。在治疗前、治疗后1、3mo 比较两组患者的复视分级、眼球运动障碍分级情况以及治疗后的并发症情况(脱出、移位、感染)。  结果:两组患眼均为Ⅰ期愈合,均无瘢痕形成。观察组与对照组患者术后1mo 的复视分级为0级的比例分别为63%与40%,

  10. Biomechanical comparison of reconstruction plate versus pedicle screw-rod system in fixation of the models of Tile B1 pelvic injury%钢板与钉棒系统固定骨盆Tile B1型损伤模型的生物力学比较

    Institute of Scientific and Technical Information of China (English)

    李尚政; 苏伟; 庄小强; 白宇; 陆生林

    2014-01-01

    Objective To compare the biomechanical properties of reconstruction plate and pedicle screw-rod system in fixation of the models of Tile B1 pelvic injury.Methods We used 7 cadaveric specimens of normal adult pelvis from 2 males and 5 females with an average death age of 42.1 years.The cadaveric pelvis preserved an intact spine from the fifth lumbar vertebra to 20 centimeters above the proximal ends of both femurs,intact pubic symphysis,bilateral hip joints,bilateral sacroiliac joints,and major pelvic ligaments.After the pelvic specimens were put in an AGS-X biomechanical testing machine at a simulated standing neutral posture,they were subjected to a vertical load of up to 500 N downward from the L5 vertebral body.The displacements of the symphysis pubis were recorded sequentially in the following 4 conditions:1.intact pelvis (the intact group); 2.models of Tile B1 pelvic injury simulating rotatory unstable injury of the pelvis in which the symphysis pubis was cut apart in combination with ruptures of ipsilateral sacrospinous and sacrotuberous ligaments (the injury group); 3.Tile B1 pelvic injury fixated with a reconstruction plate (the plate group).4.Tile B1 pelvic injury fixated with the pedicle screw-rod system (the screw-rod group).Results Under the vertical load of 500 N,the displacements of the symphysis pubis in the intact,injury,plate and screw-rod groups were respectively 0.121 ±0.025 mm,4.512 ±0.391 mm,0.358 ±0.051 mm,and 0.656 ±0.103 mm.There were significant differences between the 4 groups (F =725.707,P =0.000).The displacement increased from the intact group,the plate group,the screw-rod group to the injury group.The differences between any 2 groups were significant (P < 0.05).Conclusions In fixation of the models of Tile B1 pelvic injury,the reconstruction plate and the pedicle screw-rod system can both effectively restore the biomechanical stability of the injured pelvis.However,internal fixation with the reconstruction plate may yield better

  11. Global Plate Driving Forces at 50Ma

    Science.gov (United States)

    Butterworth, N. P.; Quevedo, L. E.; Müller, R. D.

    2011-12-01

    We apply a novel workflow utilising the BEM-Earth geodynamic software to analyse the global coupled plate-mantle dynamics at 50 Ma. A subduction history model based on kinematic data going as far back as 80 Ma was developed using the GPlates software. Advection of the plates into the mantle takes into account the absolute plate motions and lithospheric thickness derived from its age to produce an estimated density heterogeneity initial model condition in the upper mantle. The resulting global model consists of regions of a mantle viscosity and density structure that is post-processed to ensure smooth non-overlapping 3D surfaces. BEM-Earth is then free to evolve the model toward the 50 Ma solution. The evolution of the model is driven by self-consistent buoyancy driven mantle dynamics. We use the model velocity output to quantify changes in forces driving the plates before and after 50 Ma. We analyse the rapid change in plate motion of India, Africa and plates in the Pacific Ocean basin by considering slab-pull, ridge-push and mantle drag/suction forces that naturally result from such top-down driven mantle flow. We compare the results with plate kinematic reconstructions and other geological observations.

  12. Intra-European Student Mobility in International Higher Education Circuits. Europe on the Move

    NARCIS (Netherlands)

    Van Mol, C.

    2014-01-01

    Intra-European Student Mobility in International Higher Education Circuits focuses on the phenomenon of international student exchanges in Europe. Strongly interdisciplinary in its focus, this book empirically addresses four main research questions: who goes abroad, how students reconstruct their

  13. Quantitative morphometric study of the subaxial cervical vertebrae end plate.

    Science.gov (United States)

    Feng, Hang; Fang, Xiangyi; Huang, Dageng; Yu, Chengcheng; Zhao, Songchuan; Hao, Dingjun

    2017-02-01

    Cervical disc arthroplasty has been gradually adopted as an alternative for the treatment of cervical degenerative disease. However, there is a large discrepancy between footprints of currently available cervical disc prostheses and anatomic dimensions of cervical end plates. This study aimed to accurately and comprehensively quantify the three-dimensional (3D) anatomic morphology of the cervical vertebral end plate and provide a theoretical basis for designing appropriate disc prostheses. Moreover, we introduced a novel geometric and mechanical model for 3D reconstruction techniques of the cervical end plate. A descriptive study of the geometry of the middle and lower cervical vertebral end plates in cadaveric spines was carried out. A total of 138 cervical vertebral end plates were digitized using an optical 3D range scanning system, and then each end plate was reconstructed using the digitized image. For each end plate, the morphologic characteristics of six surface curves and the end plate concavity depth were symmetrically chosen and depicted. The cranial end plates (relative to the disc) were concave and the caudal end plates were relatively flat at all disc levels, with mean concavity depths of 2.04 and 0.69 mm, respectively. For the caudal end plates, the end plate concavity apex was most often (81.42%) located in the posterior portion, whereas in the cranial end plates, the distribution was relatively even. For the sagittal curves, the foremost point and the rearmost point on the middle curve had a more forward position than those in the left curve and the right curve. Regarding the frontal plane curves, the length of the middle curve was longer than that of the anterior curve and posterior curve. For the cranial end plate, the maximal mean depth was the middle curve, whereas for the caudal end plate, the maximum depth was the posterior curve. There is marked morphologic asymmetry, in that the cranial end plate is more concave than the corresponding

  14. Computer animation of Phanerozoic plate motions

    Energy Technology Data Exchange (ETDEWEB)

    Scotese, C.R. (Univ. of Texas, Arlington, TX (United States). Dept. of Geology)

    1992-01-01

    Since 1985, the PALEOMAP Project, in collaboration with research groups both in the US and abroad, has assembled a digital model that describes global plate motions during the last 600 million years. In this paper the authors present a series of computer animations that dynamically illustrates the movement of continents and terranes, and the evolution of the ocean basins since the breakup of the late Precambrian supercontinent. These animations depict the motion of the plates from both equatorial and polar perspectives. Mesozoic and Cenozoic plate tectonic reconstructions are based on a synthesis of linear magnetic anomalies, fracture zone locations, intracontinental rifts, collision and thrust belts, and zones of strike-slip. Paleozoic plate reconstructions, though more speculative, are based on evidence of past subduction, continental collision, and inferred sea floor spreading. The relative longitudinal positions of the continents during the Paleozoic and the width of intervening oceans have been adjusted to best explain changing biogeographic and paleoclimatic patterns. A new paleomagnetic/hot spot reference frame has been constructed that combines paleomagnetic data compiled by Rob Van der Voo (1992) with inferred motion relative to a fixed frame of hot spots. Using probable Early Mesozoic and Paleozoic hot spot tracks on the major continents, the authors have extended plate motions relative to the hot spot reference frame back to 400 million years.

  15. Aluminum heat sink enables power transistors to be mounted integrally with printed circuit board

    Science.gov (United States)

    Seaward, R. C.

    1967-01-01

    Power transistor is provided with an integral flat plate aluminum heat sink which mounts directly on a printed circuit board containing associated circuitry. Standoff spacers are used to attach the heat sink to the printed circuit board containing the remainder of the circuitry.

  16. Printed circuits. Citations from the NTIS data base

    Science.gov (United States)

    Reed, W. E.

    1980-04-01

    The design, fabrication, testing, and applications of printed circuits are presented in these citations of Federally-sponsored research reports. Research on computer aided design, soldering, etching, plating, photolithography, and materials are cited. This updated bibliography contains 175 abstracts, 41 of which are new entries to the previous edition.

  17. GaAs IMPATT diodes for microstrip circuit applications.

    Science.gov (United States)

    Wisseman, W. R.; Tserng, H. Q.; Shaw, D. W.; Mcquiddy, D. N.

    1972-01-01

    GaAs IMPATT diodes with plated heat sinks are shown to be particularly well suited for microstrip circuit applications. Details of materials growth and device fabrication procedures are given, and experimental results are presented for a GaAs IMPATT microstrip oscillator operating at X band.

  18. Approximate circuits for increased reliability

    Energy Technology Data Exchange (ETDEWEB)

    Hamlet, Jason R.; Mayo, Jackson R.

    2015-08-18

    Embodiments of the invention describe a Boolean circuit having a voter circuit and a plurality of approximate circuits each based, at least in part, on a reference circuit. The approximate circuits are each to generate one or more output signals based on values of received input signals. The voter circuit is to receive the one or more output signals generated by each of the approximate circuits, and is to output one or more signals corresponding to a majority value of the received signals. At least some of the approximate circuits are to generate an output value different than the reference circuit for one or more input signal values; however, for each possible input signal value, the majority values of the one or more output signals generated by the approximate circuits and received by the voter circuit correspond to output signal result values of the reference circuit.

  19. Approximate circuits for increased reliability

    Energy Technology Data Exchange (ETDEWEB)

    Hamlet, Jason R.; Mayo, Jackson R.

    2015-12-22

    Embodiments of the invention describe a Boolean circuit having a voter circuit and a plurality of approximate circuits each based, at least in part, on a reference circuit. The approximate circuits are each to generate one or more output signals based on values of received input signals. The voter circuit is to receive the one or more output signals generated by each of the approximate circuits, and is to output one or more signals corresponding to a majority value of the received signals. At least some of the approximate circuits are to generate an output value different than the reference circuit for one or more input signal values; however, for each possible input signal value, the majority values of the one or more output signals generated by the approximate circuits and received by the voter circuit correspond to output signal result values of the reference circuit.

  20. 喉切除对叠式气-食管通路发音重建防治误咽的研究%Effect of whole laryngectomy on vocal reconstruction of tracheaesophageal circuit and prevention and treatment of accidental aspiration

    Institute of Scientific and Technical Information of China (English)

    蒋立新; 张向博; 刘新; 孙连玉

    2003-01-01

    目的晚期喉癌行全喉切除发音重建及防误咽一直是头颈肿瘤外科攻关难题 ,研究气-食管通路发声重建防治误咽的新方法 ,评价对叠式气-食管通路发声口重建及檐状会厌 "成形术防治误咽的疗效.方法将纵形切开的气-食管漏行衣襟样对叠缝合;保留带蒂环状软骨瓣并修成会厌形状;在重建气-食管通路发声口上方将会厌形状骨片植入食道前壁粘膜下,使曲面向下凸入食管腔形成檐状会厌".结果 33例喉鳞癌术后 3,7或 12 d 拔除鼻饲管,经 6~ 11 d常规进食适应后均无误咽.随访 2~ 5年, 28例无发声口漏, 2例癌复发肺、骨转移死亡, 3例失访.结论对叠式气-食管通路发声口及"檐状会厌"有效地防治误咽.%Aim To estimate the curative effect of vocal reconstruction of tracheaesophageal passway and the brim shape epiglottis plasty.Methods A pedicel cricoid cartilage flap had been built as well as the epiglottis after total laryngectomy.A downward concave face of the brim shape epiglottis above the phonatory opening from the posterior wall of the trachea and the anterior wall of the esophagus was made.Results The nasal feeding tube was pulled out 3,7 or 12 days after operation of larynx squamous carcinoma and there was no any patient with accidental aspiration after routine eating for 6 to 11 days.Of 33 cases undergoing this operation, 27 patients had not happened food aspiration, 2 cases died due to recurrence of the carcinoma, 3 cases failed to follow up.Conclusion We consider this method not only can avoid aspiration of the food but also is advantageous to the function of speech and swallowing in different degree.

  1. Plasmonic Nanoguides and Circuits

    CERN Document Server

    Bozhevolnyi, Sergey

    2008-01-01

    Modern communication systems dealing with huge amounts of data at ever increasing speed try to utilize the best aspects of electronic and optical circuits. Electronic circuits are tiny but their operation speed is limited, whereas optical circuits are extremely fast but their sizes are limited by diffraction. Waveguide components utilizing surface plasmon (SP) modes were found to combine the huge optical bandwidth and compactness of electronics, and plasmonics thereby began to be considered as the next chip-scale technology. In this book, the authors concentrate on the SP waveguide configurati

  2. Optoelectronics circuits manual

    CERN Document Server

    Marston, R M

    2013-01-01

    Optoelectronics Circuits Manual covers the basic principles and characteristics of the best known types of optoelectronic devices, as well as the practical applications of many of these optoelectronic devices. The book describes LED display circuits and LED dot- and bar-graph circuits and discusses the applications of seven-segment displays, light-sensitive devices, optocouplers, and a variety of brightness control techniques. The text also tackles infrared light-beam alarms and multichannel remote control systems. The book provides practical user information and circuitry and illustrations.

  3. Circuit analysis with Multisim

    CERN Document Server

    Baez-Lopez, David

    2011-01-01

    This book is concerned with circuit simulation using National Instruments Multisim. It focuses on the use and comprehension of the working techniques for electrical and electronic circuit simulation. The first chapters are devoted to basic circuit analysis.It starts by describing in detail how to perform a DC analysis using only resistors and independent and controlled sources. Then, it introduces capacitors and inductors to make a transient analysis. In the case of transient analysis, it is possible to have an initial condition either in the capacitor voltage or in the inductor current, or bo

  4. Modern TTL circuits manual

    CERN Document Server

    Marston, R M

    2013-01-01

    Modern TTL Circuits Manual provides an introduction to the basic principles of Transistor-Transistor Logic (TTL). This book outlines the major features of the 74 series of integrated circuits (ICs) and introduces the various sub-groups of the TTL family.Organized into seven chapters, this book begins with an overview of the basics of digital ICs. This text then examines the symbology and mathematics of digital logic. Other chapters consider a variety of topics, including waveform generator circuitry, clocked flip-flop and counter circuits, special counter/dividers, registers, data latches, com

  5. Pragmatic circuits frequency domain

    CERN Document Server

    Eccles, William

    2006-01-01

    Pragmatic Circuits: Frequency Domain goes through the Laplace transform to get from the time domain to topics that include the s-plane, Bode diagrams, and the sinusoidal steady state. This second of three volumes ends with a-c power, which, although it is just a special case of the sinusoidal steady state, is an important topic with unique techniques and terminology. Pragmatic Circuits: Frequency Domain is focused on the frequency domain. In other words, time will no longer be the independent variable in our analysis. The two other volumes in the Pragmatic Circuits series include titles on DC

  6. Gallium Arsenide Domino Circuit

    Science.gov (United States)

    Yang, Long; Long, Stephen I.

    1990-01-01

    Advantages include reduced power and high speed. Experimental gallium arsenide field-effect-transistor (FET) domino circuit replicated in large numbers for use in dynamic-logic systems. Name of circuit denotes mode of operation, which logic signals propagate from each stage to next when successive stages operated at slightly staggered clock cycles, in manner reminiscent of dominoes falling in a row. Building block of domino circuit includes input, inverter, and level-shifting substages. Combinational logic executed in input substage. During low half of clock cycle, result of logic operation transmitted to following stage.

  7. Troubleshooting analog circuits

    CERN Document Server

    Pease, Robert A

    1991-01-01

    Troubleshooting Analog Circuits is a guidebook for solving product or process related problems in analog circuits. The book also provides advice in selecting equipment, preventing problems, and general tips. The coverage of the book includes the philosophy of troubleshooting; the modes of failure of various components; and preventive measures. The text also deals with the active components of analog circuits, including diodes and rectifiers, optically coupled devices, solar cells, and batteries. The book will be of great use to both students and practitioners of electronics engineering. Other

  8. Monolithic microwave integrated circuits

    Science.gov (United States)

    Pucel, R. A.

    Monolithic microwave integrated circuits (MMICs), a new microwave technology which is expected to exert a profound influence on microwave circuit designs for future military systems as well as for the commercial and consumer markets, is discussed. The book contains an historical discussion followed by a comprehensive review presenting the current status in the field. The general topics of the volume are: design considerations, materials and processing considerations, monolithic circuit applications, and CAD, measurement, and packaging techniques. All phases of MMIC technology are covered, from design to testing.

  9. Clinical comparative study of antiglide reconstruction plates by posterior-lateral approach and an-atomical plates by lateral approach in treatment of Danis-Weber type B trimalleolar fractures%后外侧抗滑重建钢板与外侧解剖钢板在治疗Danis-Weber B 型三踝骨折的对比研究

    Institute of Scientific and Technical Information of China (English)

    王冰一; 潘芋钢; 吴学建; 郑飞; 孟祥雷

    2016-01-01

    Objective To investigate the clinical effects of antiglide plates and anatomical plates on Danis-Weber type B trimalleolar fractures. Methods All the 46 Danis-Weber type B trimalleolar fractures meeting the inclusion criteria were treated from June 2011 to August 2013. The 21 patients were treated by antiglide plate via posterolateral approach,the other 25 patients were treated by anatomical plate by posterior approach. The patients undertook a follow-up of 12-36 months,14. 6 months on aver-age. Complications such as infection,nonunion,peroneal tendonitis were observed. Ankle functions were assessed according to the Olerud and Monlander scoring system one year after surgery. All the data inclu-ding injury to operation time,operating room time,hospital stay and ankle joint functional scores,were analyzed with complete randomized design t-test. Results There was no difference in injury to operation time,operating room time,hospital stay or ankle joint functional scores between the two methods. Conclusions For Danis-Weber type B trimalleolar fractures,clinical results between antiglide plates and anatomical plates do not show statistical differences.%目的:对比研究后外侧抗滑重建钢板与外侧解剖钢板治疗 Danis-Weber B 型三踝骨折的临床疗效。方法回顾性分析2011年6月至2013年8月符合纳入标准的46例 Danis-Weber B 型三踝骨折患者的临床资料,21例患者采用后外侧抗滑重建钢板治疗,25例患者采用外侧解剖钢板治疗,术后随访12~36个月,平均14.6个月。观察术后切口感染、骨折不愈合、腓骨肌腱炎等并发症,术后1年应用 Olerud and Monlander 系统对患者进行踝关节功能评分,采用成组设计的 t 检验,对两组受伤至手术时间、手术时间、住院时间以及踝关节功能评分进行评价。结果两组受伤至手术时间、手术时间、住院时间以及踝关节功能评分比较差异均未见统计学意义( P 均>0.05

  10. Validation of the Gate simulation platform in single photon emission computed tomography and application to the development of a complete 3-dimensional reconstruction algorithm; Validation de la plate-forme de simulation GATE en tomographie a emission monophotonique et application au developpement d'un algorithme de reconstruction 3D complete

    Energy Technology Data Exchange (ETDEWEB)

    Lazaro, D

    2003-10-01

    Monte Carlo simulations are currently considered in nuclear medical imaging as a powerful tool to design and optimize detection systems, and also to assess reconstruction algorithms and correction methods for degrading physical effects. Among the many simulators available, none of them is considered as a standard in nuclear medical imaging: this fact has motivated the development of a new generic Monte Carlo simulation platform (GATE), based on GEANT4 and dedicated to SPECT/PET (single photo emission computed tomography / positron emission tomography) applications. We participated during this thesis to the development of the GATE platform within an international collaboration. GATE was validated in SPECT by modeling two gamma cameras characterized by a different geometry, one dedicated to small animal imaging and the other used in a clinical context (Philips AXIS), and by comparing the results obtained with GATE simulations with experimental data. The simulation results reproduce accurately the measured performances of both gamma cameras. The GATE platform was then used to develop a new 3-dimensional reconstruction method: F3DMC (fully 3-dimension Monte-Carlo) which consists in computing with Monte Carlo simulation the transition matrix used in an iterative reconstruction algorithm (in this case, ML-EM), including within the transition matrix the main physical effects degrading the image formation process. The results obtained with the F3DMC method were compared to the results obtained with three other more conventional methods (FBP, MLEM, MLEMC) for different phantoms. The results of this study show that F3DMC allows to improve the reconstruction efficiency, the spatial resolution and the signal to noise ratio with a satisfactory quantification of the images. These results should be confirmed by performing clinical experiments and open the door to a unified reconstruction method, which could be applied in SPECT but also in PET. (author)

  11. Create Your Plate

    Medline Plus

    Full Text Available ... steps to get started: Using your dinner plate, put a line down the middle of the plate. ... vegetables . Now in one of the small sections, put grains and starchy foods. See this list of ...

  12. Create Your Plate

    Medline Plus

    Full Text Available ... Your Plate It's simple and effective for both managing diabetes and losing weight. Creating your plate lets ... 2016 Articles from Diabetes Forecast® magazine: wcie-meal-planning, In this section Food Planning Meals Diabetes Meal ...

  13. Create Your Plate

    Medline Plus

    Full Text Available ... Your Plate Gluten Free Diets Meal Planning for Vegetarian Diets Cook with Heart-Healthy Foods Holiday Meal ... Healthy Diet Create Your Plate Meal Planning for Vegetarian Diets Gluten Free Diets Holiday Meal Planning Cook ...

  14. Food guide plate

    Science.gov (United States)

    ... chips or cookies. VEGETABLES: MAKE HALF OF YOUR PLATE FRUITS AND VEGETABLES Vegetables can be raw, fresh, ... as a snack. FRUITS: MAKE HALF OF YOUR PLATE FRUITS AND VEGETABLES Fruits can be fresh, canned, ...

  15. Growth Plate Fractures

    Science.gov (United States)

    ... the most widely used by doctors is the Salter-Harris system, described below. Type I Fractures These ... incidence of growth plate fractures peaks in adolescence. Salter-Harris classification of growth plate fractures. AAOS does ...

  16. Create Your Plate

    Medline Plus

    Full Text Available ... Planning Meals Diabetes Meal Plans Create Your Plate Gluten Free Diets Meal Planning for Vegetarian Diets Cook ... Create Your Plate Meal Planning for Vegetarian Diets Gluten Free Diets Holiday Meal Planning Cook with Heart- ...

  17. Create Your Plate

    Medline Plus

    Full Text Available ... Planning Meals Diabetes Meal Plans Create Your Plate Gluten Free Diets Meal Planning for Vegetarian Diets Cook ... Create Your Plate Meal Planning for Vegetarian Diets Gluten Free Diets Holiday Meal Planning Cook with Heart- ...

  18. Create Your Plate

    Medline Plus

    Full Text Available ... Your Plate It's simple and effective for both managing diabetes and losing weight. Creating your plate lets you still choose the foods you want, but changes the portion sizes so you are getting larger ...

  19. Create Your Plate

    Medline Plus

    Full Text Available ... Your Plate It's simple and effective for both managing diabetes and losing weight. Creating your plate lets ... Sleeve Custom jerseys for your Tour de Cure team benefits the cause. Ask the Experts: Learn to ...

  20. Accelerated plate tectonics.

    Science.gov (United States)

    Anderson, D L

    1975-03-21

    The concept of a stressed elastic lithospheric plate riding on a viscous asthenosphere is used to calculate the recurrence interval of great earthquakes at convergent plate boundaries, the separation of decoupling and lithospheric earthquakes, and the migration pattern of large earthquakes along an arc. It is proposed that plate motions accelerate after great decoupling earthquakes and that most of the observed plate motions occur during short periods of time, separated by periods of relative quiescence.

  1. Circuit enhances vertical resolution in raster scanning systems

    Science.gov (United States)

    Alsovsky, W. H.; Greenwood, J. R.; Holley, O. M.

    1968-01-01

    Circuit enhances vertical resolution in electron beam, raster scanning systems exhibiting aperture distortion in the vertical direction. A sensitized area /image/ produces a video output when the scan beam nears it, which causes vertical elongation in the reconstructed images of all sensitized areas on the surface.

  2. Printed circuit for ATLAS

    CERN Multimedia

    Laurent Guiraud

    1999-01-01

    A printed circuit board made by scientists in the ATLAS collaboration for the transition radiaton tracker (TRT). This will read data produced when a high energy particle crosses the boundary between two materials with different electrical properties.

  3. Latching overcurrent circuit breaker

    Science.gov (United States)

    Moore, M. L.

    1970-01-01

    Circuit breaker consists of a preset current amplitude sensor, and a lamp-photo-resistor combination in a feedback arrangement which energizes a power switching relay. The ac input power is removed from the load at predetermined current amplitudes.

  4. High temperature circuit breaker

    Science.gov (United States)

    Edwards, R. N.; Travis, E. F.

    1970-01-01

    Alternating current circuit breaker is suitable for reliable long-term service at 1000 deg F in the vacuum conditions of outer space. Construction materials are resistant to nuclear radiation and vacuum welding. Service test conditions and results are given.

  5. Nonlinear Reconstruction

    CERN Document Server

    Zhu, Hong-Ming; Pen, Ue-Li; Chen, Xuelei; Yu, Hao-Ran

    2016-01-01

    We present a direct approach to non-parametrically reconstruct the linear density field from an observed non-linear map. We solve for the unique displacement potential consistent with the non-linear density and positive definite coordinate transformation using a multigrid algorithm. We show that we recover the linear initial conditions up to $k\\sim 1\\ h/\\mathrm{Mpc}$ with minimal computational cost. This reconstruction approach generalizes the linear displacement theory to fully non-linear fields, potentially substantially expanding the BAO and RSD information content of dense large scale structure surveys, including for example SDSS main sample and 21cm intensity mapping.

  6. Create Your Plate

    Medline Plus

    Full Text Available ... Reset Plate Share Create Your Plate ! Share: Seven Simple Steps to Create Your Plate It's simple and effective for both managing diabetes and losing ... en.html Have Type 2 Diabetes? Our free program will help you live well. More from diabetes. ...

  7. Overriding Faulty Circuit Breakers

    Science.gov (United States)

    Robbins, Richard L.; Pierson, Thomas E.

    1987-01-01

    Retainer keeps power on in emergency. Simple mechanical device attaches to failed aircraft-type push/pull circuit breaker to restore electrical power temporarily until breaker replaced. Device holds push/pull button in closed position; unnecessary for crewmember to hold button in position by continual finger pressure. Sleeve and plug hold button in, overriding mechanical failure in circuit breaker. Windows in sleeve show button position.

  8. 腓骨重建及小钛板固定下颌骨体部缺损的三维有限元分析%Fibula reconstruction and small titanium plate fixation for repair of mandibular body defects:a three-dimensional finite element analysis

    Institute of Scientific and Technical Information of China (English)

    陈彪; 屈鹏飞; 刘耀强; 范戌辉; 刘吉伦; 杨威

    2015-01-01

    的应力比较大,应重视其稳定性和固位性;前牙咬合时的应力大于后牙咬合时的应力,修复后应避免前牙咬合。%BACKGROUND: In clinic,the mechanical study about fibula reconstruction for the repair of mandibular bone defect is unrealistic; the finite element analysis, however, provides a new approach for the biomechanical study of mandibular reconstruction. OBJECTIVE: To establish the three-dimensional finite element model of mandibular body defect under fibula reconstruction and smal titanium plate fixation, and to analyze the biomechanical features. METHODS:The three-dimensional model of mandibular body defect under fibula reconstruction and internal fixation was established. 100 N bite force was loaded on the anterior teeth, contralateral first molar and contralateral second molar, respectively. The maximum stress and maximum displacement before and after model reconstruction, the stress of bone tissues around the titanium plate and titanium screw holes under anterior and posterior loading, and the maximum displacement of the front and rear ends of the fibula under anterior and posterior loading were observed. RESULTS AND CONCLUSION:The maximum stress of the normal mandible concentrated in the condylar neck. In the reconstructed models, the maximum stress concentrated in the contralateral condylar neck. Under the same bite force, the maximum stress value of the reconstructed mandibular model was greater than that of the normal mandible. The maximum stress value of the anterior teeth was greater than that of the posterior teeth. The stress value was maximal between two screw holes inside each titanium plate and almost concentrated in the mandibular angle. The maximum stress of the residual titanium screw of the mandible concentrated in the first titanium screw over the mandibular defect under loading, while the maximum stress of the titanium screw of the fibular end concentrated in the titanium screw below the mesial segment of

  9. Heterogeneous photonic integrated circuits

    Science.gov (United States)

    Fang, Alexander W.; Fish, Gregory; Hall, Eric

    2012-01-01

    Photonic Integrated Circuits (PICs) have been dichotomized into circuits with high passive content (silica and silicon PLCs) and high active content (InP tunable lasers and transceivers) due to the trade-off in material characteristics used within these two classes. This has led to restrictions in the adoption of PICs to systems in which only one of the two classes of circuits are required to be made on a singular chip. Much work has been done to create convergence in these two classes by either engineering the materials to achieve the functionality of both device types on a single platform, or in epitaxial growth techniques to transfer one material to the next, but have yet to demonstrate performance equal to that of components fabricated in their native substrates. Advances in waferbonding techniques have led to a new class of heterogeneously integrated photonic circuits that allow for the concurrent use of active and passive materials within a photonic circuit, realizing components on a transferred substrate that have equivalent performance as their native substrate. In this talk, we review and compare advances made in heterogeneous integration along with demonstrations of components and circuits enabled by this technology.

  10. Hollow lag screws combined with reconstruction plates for treatment of high anterior column fracture of the acetabulum with intact true pelvic brim%空心拉力螺钉联合重建钢板治疗真骨盆缘完整的髋臼高位前柱骨折

    Institute of Scientific and Technical Information of China (English)

    周炎; 刘世清; 瞿新丛; 余铃; 廖琦; 黄涛; 赵奇; 张春

    2014-01-01

    目的 探讨真骨盆缘完整的髋臼高位前柱骨折采用空心拉力螺钉联合重建钢板固定的疗效.方法 2009年6月-2012年9月收治真骨盆缘完整的髋臼高位前柱骨折6例,其中挤压伤4例,高处坠落伤2例;参照谭国庆等分型:单纯型4例,粉碎型2例.采用髂股入路先行髋臼顶复位空心拉力螺钉固定,后复位、重建钢板固定髂骨翼及髂嵴.结果 6例术后随访12~24个月,平均18个月.所有患者骨折均愈合,愈合时间12 ~ 18周,平均16周.术后按Matta影像学评定标准,优5例,良1例,优良率100%.末次随访时按Matta改良的Merle d'Aubigne和Postel髋关节功能评分标准,优4例,良2例,优良率100%.术后2例出现股外侧皮神经麻痹,口服神经营养药物2~3个月后均恢复.结论 空心拉力螺钉联合重建钢板治疗真骨盆缘完整的髋臼高位前柱骨折固定可靠,临床疗效满意.%Objective To investigate the clinical effect of high anterior column fracture of the acetabulum with intact true pelvic brim fixed using hollow lag screws plus reconstruction plates.Methods All cases of high anterior column fracture of the acetabulum with intact true pelvic brim treated from June 2009 to September 2012 were included.Crush contributed to injury in 4 cases and high fall to injury in 2 cases.According to Tan Guoqing' s classification,4 cases were classified as simple type and 2 cases comminuted type.All cases were treated through iliofemoral approach to reduce and fix acetabular roof by hollow lag screws firstly,and then fix iliac wing and iliac crest by reconstruction plates.Results Six cases were followed up for mean 18 months (range,12-24 months).Fracture healed after mean 16 weeks (range,12-18 weeks).Radiological results assessed using Matta' s score system were excellent in 5 cases and good in 1 case with good to excellent rate of 100%.At the final follow-up,Merle d' Aubigne and Postel hip score was excellent in 4 cases and good in 2

  11. Magnetic circuit for hall effect plasma accelerator

    Science.gov (United States)

    Manzella, David H. (Inventor); Jacobson, David T. (Inventor); Jankovsky, Robert S. (Inventor); Hofer, Richard (Inventor); Peterson, Peter (Inventor)

    2009-01-01

    A Hall effect plasma accelerator includes inner and outer electromagnets, circumferentially surrounding the inner electromagnet along a thruster centerline axis and separated therefrom, inner and outer magnetic conductors, in physical connection with their respective inner and outer electromagnets, with the inner magnetic conductor having a mostly circular shape and the outer magnetic conductor having a mostly annular shape, a discharge chamber, located between the inner and outer magnetic conductors, a magnetically conducting back plate, in magnetic contact with the inner and outer magnetic conductors, and a combined anode electrode/gaseous propellant distributor, located at a bottom portion of the discharge chamber. The inner and outer electromagnets, the inner and outer magnetic conductors and the magnetically conducting back plate form a magnetic circuit that produces a magnetic field that is largely axial and radially symmetric with respect to the thruster centerline.

  12. Optimisation and validation of a 3D reconstruction algorithm for single photon emission computed tomography by means of GATE simulation platform; Optimisation et validation d'un algorithme de reconstruction 3D en Tomographie d'Emission Monophotonique a l'aide de la plate forme de simulation GATE

    Energy Technology Data Exchange (ETDEWEB)

    El Bitar, Ziad [Ecole Doctorale des Sciences Fondamentales, Universite Blaise Pascal, U.F.R de Recherches Scientifiques et Techniques, 34, avenue Carnot - BP 185, 63006 Clermont-Ferrand Cedex (France); Laboratoire de Physique Corpusculaire, CNRS/IN2P3, 63177 Aubiere (France)

    2006-12-15

    Although time consuming, Monte-Carlo simulations remain an efficient tool enabling to assess correction methods for degrading physical effects in medical imaging. We have optimized and validated a reconstruction method baptized F3DMC (Fully 3D Monte Carlo) in which the physical effects degrading the image formation process were modelled using Monte-Carlo methods and integrated within the system matrix. We used the Monte-Carlo simulation toolbox GATE. We validated GATE in SPECT by modelling the gamma-camera (Philips AXIS) used in clinical routine. Techniques of threshold, filtering by a principal component analysis and targeted reconstruction (functional regions, hybrid regions) were used in order to improve the precision of the system matrix and to reduce the number of simulated photons as well as the time consumption required. The EGEE Grid infrastructures were used to deploy the GATE simulations in order to reduce their computation time. Results obtained with F3DMC were compared with the reconstruction methods (FBP, ML-EM, MLEMC) for a simulated phantom and with the OSEM-C method for the real phantom. Results have shown that the F3DMC method and its variants improve the restoration of activity ratios and the signal to noise ratio. By the use of the grid EGEE, a significant speed-up factor of about 300 was obtained. These results should be confirmed by performing studies on complex phantoms and patients and open the door to a unified reconstruction method, which could be used in SPECT and also in PET. (author)

  13. Fractal zone plate beam based optical tweezers

    Science.gov (United States)

    Cheng, Shubo; Zhang, Xinyu; Ma, Wenzhuo; Tao, Shaohua

    2016-01-01

    We demonstrate optical manipulation with an optical beam generated by a fractral zone plate (FZP). The experimental results show that the FZP beam can simultaneously trap multiple particles positioned in different focal planes of the FZP beam, owing to the multiple foci and self-reconstruction property of the FZP beam. The FZP beam can also be used to construct three-dimensional optical tweezers for potential applications. PMID:27678305

  14. Chaotic behavior learning of Chua's circuit

    Institute of Scientific and Technical Information of China (English)

    Sun Jian-Cheng

    2012-01-01

    Least-square support vector machines (LS-SVM) are applied for learning the chaotic behavior of Chua's circuit.The system is divided into three multiple-input single-output (MISO) structures and the LS-SVM are trained individually.Comparing with classical approaches,the proposed one reduces the structural complexity and the selection of parameters is avoided.Some parameters of the attractor are used to compare the chaotic behavior of the reconstructed and the original systems for model validation.Results show that the LS-SVM combined with the MISO can be trained to identify the underlying link among Chua's circuit state variables,and exhibit the chaotic attractors under the autonomous working mode.

  15. Inductorless Chua's Circuit: Experimental Time Series Analysis

    Directory of Open Access Journals (Sweden)

    R. M. Rubinger

    2007-01-01

    Full Text Available We have implemented an operational amplifier inductorless realization of the Chua's circuit. We have registered time series from its dynamical variables with the resistor R as the control parameter and varying from 1300 Ω to 2000 Ω. Experimental time series at fixed R were used to reconstruct attractors by the delay vector technique. The flow attractors and their Poincaré maps considering parameters such as the Lyapunov spectrum, its subproduct the Kaplan-Yorke dimension, and the information dimension are also analyzed here. The results for a typical double scroll attractor indicate a chaotic behavior characterized by a positive Lyapunov exponent and with a Kaplan-Yorke dimension of 2.14. The occurrence of chaos was also investigated through numerical simulations of the Chua's circuit set of differential equations.

  16. Abrupt plate accelerations shape rifted continental margins

    Science.gov (United States)

    Brune, Sascha; Williams, Simon E.; Butterworth, Nathaniel P.; Müller, R. Dietmar

    2016-08-01

    Rifted margins are formed by persistent stretching of continental lithosphere until breakup is achieved. It is well known that strain-rate-dependent processes control rift evolution, yet quantified extension histories of Earth’s major passive margins have become available only recently. Here we investigate rift kinematics globally by applying a new geotectonic analysis technique to revised global plate reconstructions. We find that rifted margins feature an initial, slow rift phase (less than ten millimetres per year, full rate) and that an abrupt increase of plate divergence introduces a fast rift phase. Plate acceleration takes place before continental rupture and considerable margin area is created during each phase. We reproduce the rapid transition from slow to fast extension using analytical and numerical modelling with constant force boundary conditions. The extension models suggest that the two-phase velocity behaviour is caused by a rift-intrinsic strength-velocity feedback, which can be robustly inferred for diverse lithosphere configurations and rheologies. Our results explain differences between proximal and distal margin areas and demonstrate that abrupt plate acceleration during continental rifting is controlled by the nonlinear decay of the resistive rift strength force. This mechanism provides an explanation for several previously unexplained rapid absolute plate motion changes, offering new insights into the balance of plate driving forces through time.

  17. Abrupt plate accelerations shape rifted continental margins.

    Science.gov (United States)

    Brune, Sascha; Williams, Simon E; Butterworth, Nathaniel P; Müller, R Dietmar

    2016-08-11

    Rifted margins are formed by persistent stretching of continental lithosphere until breakup is achieved. It is well known that strain-rate-dependent processes control rift evolution, yet quantified extension histories of Earth's major passive margins have become available only recently. Here we investigate rift kinematics globally by applying a new geotectonic analysis technique to revised global plate reconstructions. We find that rifted margins feature an initial, slow rift phase (less than ten millimetres per year, full rate) and that an abrupt increase of plate divergence introduces a fast rift phase. Plate acceleration takes place before continental rupture and considerable margin area is created during each phase. We reproduce the rapid transition from slow to fast extension using analytical and numerical modelling with constant force boundary conditions. The extension models suggest that the two-phase velocity behaviour is caused by a rift-intrinsic strength--velocity feedback, which can be robustly inferred for diverse lithosphere configurations and rheologies. Our results explain differences between proximal and distal margin areas and demonstrate that abrupt plate acceleration during continental rifting is controlled by the nonlinear decay of the resistive rift strength force. This mechanism provides an explanation for several previously unexplained rapid absolute plate motion changes, offering new insights into the balance of plate driving forces through time.

  18. Intra Plate Stresses Using Finite Element Modelling

    Directory of Open Access Journals (Sweden)

    Jayalakshmi S.

    2016-10-01

    Full Text Available One of the most challenging problems in the estimation of seismic hazard is the ability to quantify seismic activity. Empirical models based on the available earthquake catalogue are often used to obtain activity of source regions. The major limitation with this approach is the lack of sufficient data near a specified source. The non-availability of data poses difficulties in obtaining distribution of earthquakes with large return periods. Such events recur over geological time scales during which tectonic processes, including mantle convection, formation of faults and new plate boundaries, are likely to take place. The availability of geometries of plate boundaries, plate driving forces, lithospheric stress field and GPS measurements has provided numerous insights on the mechanics of tectonic plates. In this article, a 2D finite element model of Indo-Australian plate is developed with the focus of representing seismic activity in India. The effect of large scale geological features including sedimentary basins, fold belts and cratons on the stress field in India is explored in this study. In order to address long term behaviour, the orientation of stress field and tectonic faults of the present Indo-Australian plate are compared with a reconstructed stress field from the early Miocene (20 Ma.

  19. ACL reconstruction - discharge

    Science.gov (United States)

    Anterior cruciate ligament reconstruction - discharge; ACL reconstruction - discharge ... had surgery to reconstruct your anterior cruciate ligament (ACL). The surgeon drilled holes in the bones of ...

  20. Angular shear plate

    Science.gov (United States)

    Ruda, Mitchell C [Tucson, AZ; Greynolds, Alan W [Tucson, AZ; Stuhlinger, Tilman W [Tucson, AZ

    2009-07-14

    One or more disc-shaped angular shear plates each include a region thereon having a thickness that varies with a nonlinear function. For the case of two such shear plates, they are positioned in a facing relationship and rotated relative to each other. Light passing through the variable thickness regions in the angular plates is refracted. By properly timing the relative rotation of the plates and by the use of an appropriate polynomial function for the thickness of the shear plate, light passing therethrough can be focused at variable positions.

  1. Circuit simulation: some humbling thoughts

    Energy Technology Data Exchange (ETDEWEB)

    Wendt, Manfred; /Fermilab

    2006-01-01

    A short, very personal note on circuit simulation is presented. It does neither include theoretical background on circuit simulation, nor offers an overview of available software, but just gives some general remarks for a discussion on circuit simulator needs in context to the design and development of accelerator beam instrumentation circuits and systems.

  2. 解剖重建锁定钢板固定治疗肱骨近端三、四部分骨折脱位%Management of proximal humeral Neer 3-part and 4-part fracture dislocations with anatomic reconstruction locking plate

    Institute of Scientific and Technical Information of China (English)

    杨国勇; 向明; 胡晓川; 陈杭; 杨顺; 唐浩琛

    2012-01-01

    Objective To analyze the therapeutic effect of open reduction with internal fixation (ORIF) and anatomic reconstruction locking plate in treatment of Neer 3-part and 4-part fracture dislocations of proximal humerus. Methods The study involved 30 patients with Neer 3-part and 4-part fracture dislocations treated with anatomic reconstruction locking plate from September 2004 to December 2007.Twenty patients had complete follow-up data.The treatment methods included locking proximal humeral plate (LPHP) in seven patients and proximal humeral internal locking system (PHILOS) in 13.There were 15 males and five females,at age range of 29-84 years (average 52.5 years),including nine patients younger than 65 years and 11 older than 65 years.According to Neer classification,there were 15 patients with 3-part fracture dislocations including 12 anterior and three posterior dislocations and five patients with 4-part fracture dislocations including four anterior and one posterior dislocations. VAS and Constant scoring system were adopted to evaluate the shoulder joint function postoperatively. Results All 20 patients were followed up for 36-71 months ( average 51 months),which showed avascular necrosis of humeral head in six patients (30%),plating loosening in two,screw penetration in six,nonunion in two and infection in two.The mean visual analogue score (VAS) was 2.55 poiuts and the mean Constant score for the shoulder was 80.8.According to the Neer shoulder functional evaluation standard,eight patients were graded as excellent,six as good,three as fair and three as poor,with excellence rate of 70%.Conclusions Although the anatomic reconstruction locking plate and ORIF can cause a high incidence of avascular necrosis of humeral head in the treatment of Neer 3-part and 4-part fracture dislocations of proximal humerus,especially for the patients older than 65 years.However,there is no obvious correlation between necrosis of humeral head and shoulder function

  3. Low latency asynchronous interface circuits

    Energy Technology Data Exchange (ETDEWEB)

    Sadowski, Greg

    2017-06-20

    In one form, a logic circuit includes an asynchronous logic circuit, a synchronous logic circuit, and an interface circuit coupled between the asynchronous logic circuit and the synchronous logic circuit. The asynchronous logic circuit has a plurality of asynchronous outputs for providing a corresponding plurality of asynchronous signals. The synchronous logic circuit has a plurality of synchronous inputs corresponding to the plurality of asynchronous outputs, a stretch input for receiving a stretch signal, and a clock output for providing a clock signal. The synchronous logic circuit provides the clock signal as a periodic signal but prolongs a predetermined state of the clock signal while the stretch signal is active. The asynchronous interface detects whether metastability could occur when latching any of the plurality of the asynchronous outputs of the asynchronous logic circuit using said clock signal, and activates the stretch signal while the metastability could occur.

  4. The clinical benefits of reconstructing the medial column support in locked plating of proximal humerus fractures%内侧柱支撑重建在锁定钢板治疗成人肱骨近端骨折中的临床意义

    Institute of Scientific and Technical Information of China (English)

    曾浪清; 陈云丰; 刘燕洁; 陈强; 王赤宇; 王磊; 张闻

    2012-01-01

    目的 探讨锁定钢板固定肱骨近端骨折术中肱骨近端内侧柱支撑重建的临床意义.方法 回顾性分析2005年6月至2010年12月采用锁定钢板治疗且获得随访的125例肱骨近端骨折患者临床资料,男54例,女71例;年龄18~88岁,平均54.6岁.骨折根据Neer分型:二部分骨折57例,三部分骨折62例,四部分骨折6例.根据术后X线片所示肱骨近端内侧柱支撑重建情况分为2组:内侧柱支撑重建组(重建组,84例)和内侧柱支撑未重建组(未重建组,41例).随访记录并比较两组患者的肩关节功能Constant评分、肱骨头内翻角度、视觉模拟评分(VAS)及并发症发生情况.结果 所有患者术后获6~30个月(平均13.6个月)随访.重建组与未重建组平均Constant评分分别为(77.9±13.0)、(67.3±11.3)分,优良率分别为72.6%、43.9%,平均VAS评分分别为(1.6±2.0)、(3.2±2.4)分,以上项目两组比较差异均有统计学意义(P<0.05);重建组术后肱骨头内翻角度(1.2°±3.3°)小于未重建组(4.4°±4.0°),术后并发症发生率(16.6%)、二次手术率(4.8%)均较未重建组(34.1%、17.0%)低,差异均有统计学意义(P<0.05).结论 锁定钢板固定肱骨近端骨折术中重建肱骨近端内侧柱支撑、骨折端良好复位不仅能使肱骨头得到有效的支撑、预防术后肱骨头内翻及内固定失败,而且术后能取得更满意的疗效.%Objective To evaluate the clinical benefits of reconstructing the medial column support in locked plating of proximal humerus fractures.Methods A retrospective analysis was conducted of the eligible 125 patients who had undergone locked plating of proximal humerus fracture in our institution between June 2005 and December 2010.They were 54 men and 71 women,18 to 88 years of age (average,54.6 years).By the Neer classification,there were 57 cases of two-part fracture,62 cases of three-part fracture and 6 cases of four-part fracture.One independent examiner

  5. Caribbean tectonics and relative plate motions

    Science.gov (United States)

    Burke, K.; Dewey, J. F.; Cooper, C.; Mann, P.; Pindell, J. L.

    1984-01-01

    During the last century, three different ways of interpreting the tectonic evolution of the Gulf of Mexico and the Caribbean have been proposed, taking into account the Bailey Willis School of a permanent pre-Jurassic deep sea basin, the Edward Suess School of a subsided continental terrain, and the Alfred Wegener School of continental separation. The present investigation is concerned with an outline of an interpretation which follows that of Pindell and Dewey (1982). An attempt is made to point out ways in which the advanced hypotheses can be tested. The fit of Africa, North America, and South America is considered along with aspects of relative motion between North and South America since the early Jurasic. Attention is given to a framework for reconstructing Caribbean plate evolution, the evolution of the Caribbean, the plate boundary zones of the northern and southern Caribbean, and the active deformation of the Caribbean plate.

  6. A semiconductor laser excitation circuit

    Energy Technology Data Exchange (ETDEWEB)

    Kaadzunari, O.; Masaty, K.

    1984-03-27

    A semiconductor laser excitation circuit is patented that is designed for operation in a pulsed mode with a high pulse repetition frequency. This circuit includes, in addition to a semiconductor laser, a high speed photodetector, a reference voltage source, a comparator, and a pulse oscillator and modulator. If the circuit is built using standard silicon integrated circuits, its speed amounts to several hundred megahertz, if it is constructed using gallium arsenide integrated circuits, its speed is several gigahertz.

  7. The Mind Grows Circuits

    CERN Document Server

    Panigrahy, Rina

    2012-01-01

    There is a vast supply of prior art that study models for mental processes. Some studies in psychology and philosophy approach it from an inner perspective in terms of experiences and percepts. Others such as neurobiology or connectionist-machines approach it externally by viewing the mind as complex circuit of neurons where each neuron is a primitive binary circuit. In this paper, we also model the mind as a place where a circuit grows, starting as a collection of primitive components at birth and then builds up incrementally in a bottom up fashion. A new node is formed by a simple composition of prior nodes when we undergo a repeated experience that can be described by that composition. Unlike neural networks, however, these circuits take "concepts" or "percepts" as inputs and outputs. Thus the growing circuits can be likened to a growing collection of lambda expressions that are built on top of one another in an attempt to compress the sensory input as a heuristic to bound its Kolmogorov Complexity.

  8. Breast Reconstruction Alternatives

    Science.gov (United States)

    ... Breast Reconstruction Surgery Breast Cancer Breast Reconstruction Surgery Breast Reconstruction Alternatives Some women who have had a ... chest. What if I choose not to get breast reconstruction? Some women decide not to have any ...

  9. Smooth Reconstruction

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    Eighty percent of the reconstruction projects in Sichuan Province will be completed by the end of the year Despite ruins still seen everywhere in the earthquake-hit areas in Sichuan (Province, new buildings have been completed, and many people have moved into new houses. Through cameras of the media, the faces, once painful and melancholy after last year’s earthquake, now look confident and firm, gratifying people all over the

  10. Neogene Caribbean plate rotation and associated Central American tectonic evolution

    Science.gov (United States)

    Wadge, G.; Burke, K.

    1983-01-01

    A theoretical model of the opening of the Cayman Trough is developed on the basis of geological evidence from a wide area. It is proposed that strike slip motion began about 30 Myr ago and proceeded at a rate of 37 + or - 6 mm/yr for a total of 1100 km of relative plate displacement, and that Central America Underwent an anticlockwise rotation with internal plate deformation. Maps of the reconstructed motion are provided.

  11. Neogene Caribbean plate rotation and associated Central American tectonic evolution

    Science.gov (United States)

    Wadge, G.; Burke, K.

    1983-01-01

    A theoretical model of the opening of the Cayman Trough is developed on the basis of geological evidence from a wide area. It is proposed that strike slip motion began about 30 Myr ago and proceeded at a rate of 37 + or - 6 mm/yr for a total of 1100 km of relative plate displacement, and that Central America Underwent an anticlockwise rotation with internal plate deformation. Maps of the reconstructed motion are provided.

  12. Maxillary reconstruction

    Directory of Open Access Journals (Sweden)

    Brown James

    2007-12-01

    Full Text Available This article aims to discuss the various defects that occur with maxillectomy with a full review of the literature and discussion of the advantages and disadvantages of the various techniques described. Reconstruction of the maxilla can be relatively simple for the standard low maxillectomy that does not involve the orbital floor (Class 2. In this situation the structure of the face is less damaged and the there are multiple reconstructive options for the restoration of the maxilla and dental alveolus. If the maxillectomy includes the orbit (Class 4 then problems involving the eye (enopthalmos, orbital dystopia, ectropion and diplopia are avoided which simplifies the reconstruction. Most controversy is associated with the maxillectomy that involves the orbital floor and dental alveolus (Class 3. A case is made for the use of the iliac crest with internal oblique as an ideal option but there are other methods, which may provide a similar result. A multidisciplinary approach to these patients is emphasised which should include a prosthodontist with a special expertise for these defects.

  13. Biomaterials for craniofacial reconstruction

    Directory of Open Access Journals (Sweden)

    Neumann, Andreas

    2009-01-01

    Full Text Available Biomaterials for reconstruction of bony defects of the skull comprise of osteosynthetic materials applied after osteotomies or traumatic fractures and materials to fill bony defects which result from malformation, trauma or tumor resections. Other applications concern functional augmentations for dental implants or aesthetic augmentations in the facial region.For ostheosynthesis, mini- and microplates made from titanium alloys provide major advantages concerning biocompatibility, stability and individual fitting to the implant bed. The necessity of removing asymptomatic plates and screws after fracture healing is still a controversial issue. Risks and costs of secondary surgery for removal face a low rate of complications (due to corrosion products when the material remains in situ. Resorbable osteosynthesis systems have similar mechanical stability and are especially useful in the growing skull.The huge variety of biomaterials for the reconstruction of bony defects makes it difficult to decide which material is adequate for which indication and for which site. The optimal biomaterial that meets every requirement (e.g. biocompatibility, stability, intraoperative fitting, product safety, low costs etc. does not exist. The different material types are (autogenic bone and many alloplastics such as metals (mainly titanium, ceramics, plastics and composites. Future developments aim to improve physical and biological properties, especially regarding surface interactions. To date, tissue engineered bone is far from routine clinical application.

  14. Chaotic memristive circuit: equivalent circuit realization and dynamical analysis

    Institute of Scientific and Technical Information of China (English)

    Bao Bo-Cheng; Xu Jian-Ping; Zhou Guo-Hua; Ma Zheng-Hua; Zou Ling

    2011-01-01

    In this paper,a practical equivalent circuit of an active flux-controlled memristor characterized by smooth piecewise-quadratic nonlinearity is designed and an experimental chaotic memristive circuit is implemented.The chaotic memristive circuit has an equilibrium set and its stability is dependent on the initial state of the memristor.The initial state-dependent and the circuit parameter-dependent dynamics of the chaotic memristive circuit are investigated via phase portraits,bifurcation diagrams and Lyapunov exponents.Both experimental and simulation results validate the proposed equivalent circuit realization of the active flux-controlled memristor.

  15. 公物理论视角下的尾号限行*--反思与重塑%Traffic Restrictions Based on the Last Digit of License Plate Numbers Under Perspective of Public Property Theory:Reflection and Reconstruction

    Institute of Scientific and Technical Information of China (English)

    周许阳

    2016-01-01

    环境法上针对尾号限行的授权,并不足以支撑其正当性。因为这种“污染防治手段”事实上还具有“交通管制”与“物权限制”的效果。学界现有讨论集中于公权对私有财产权的限制问题,却忽略了尾号限行是针对“特定道路”,而非“不特定车辆”作出的事实。对此,公物理论架起了机动车价值发挥与道路使用的桥梁,并逻辑自洽地将尾号限行的行为形式、内容、效果作为公物管理权的运作过程而纳入。如将尾号限行理解为“道路管理行为”,则其合法性来自于国家对道路的所有权或《公路法》第8条第2款的概括性管理权。尽管这种正当性根据要受到“交通目的”的限制,但却是对基于“污染防治目的”作出的限行行为正当性的补充。%The authorization of the environmental law to the traffic restrictions based on the last digit of license plate numbers is not sufficient to support its legitimacy, because this restriction is not only an ‘instrument to control air pollution’, but also effect of ‘traffic control’ and ‘restriction on property right’ in fact. The existing related discussions focus on restricting private property right by public right, while neglects the fact that the restriction is for ‘specific road’ instead of ‘unspecified vehicles’. For this, the public property theory acts as a bridge between motor vehicles' value exertion and road usage, and brings the behavior form, content and effect of the restriction under public property management right operation course logically. If the restriction is made of ‘road management behavior’, its legitimacy is from the state's ownership of road or the general management right directly granted by the article 8.2 of the Law of Road. Although such legitimacy is limited to ‘traffic purpose’, it is the supplement to the legitimacy of the restriction behavior made according to

  16. Primer printed circuit boards

    CERN Document Server

    Argyle, Andrew

    2009-01-01

    Step-by-step instructions for making your own PCBs at home. Making your own printed circuit board (PCB) might seem a daunting task, but once you master the steps, it's easy to attain professional-looking results. Printed circuit boards, which connect chips and other components, are what make almost all modern electronic devices possible. PCBs are made from sheets of fiberglass clad with copper, usually in multiplelayers. Cut a computer motherboard in two, for instance, and you'll often see five or more differently patterned layers. Making boards at home is relatively easy

  17. Current Conveyor Equivalent Circuits

    Directory of Open Access Journals (Sweden)

    Tejmal S. Rathore

    2012-02-01

    Full Text Available An equivalence between a class of (current conveyor CC II+ and CC II- circuits is established. CC IIequivalent circuit uses one extra element. However, under certain condition, the extra element can be eliminated. As an illustration of the application of this equivalence, minimal first and second order all-pass filters are derived. Incertain cases, it is possible to compensate the effect of the input resistor of CC at port X. At the end, an open problem of realizing an Nth order (N > 2 minimal all-pass filter is stated.

  18. Circuit design for reliability

    CERN Document Server

    Cao, Yu; Wirth, Gilson

    2015-01-01

    This book presents physical understanding, modeling and simulation, on-chip characterization, layout solutions, and design techniques that are effective to enhance the reliability of various circuit units.  The authors provide readers with techniques for state of the art and future technologies, ranging from technology modeling, fault detection and analysis, circuit hardening, and reliability management. Provides comprehensive review on various reliability mechanisms at sub-45nm nodes; Describes practical modeling and characterization techniques for reliability; Includes thorough presentation of robust design techniques for major VLSI design units; Promotes physical understanding with first-principle simulations.

  19. Inrush Current Control Circuit

    Science.gov (United States)

    Cole, Steven W. (Inventor)

    2002-01-01

    An inrush current control circuit having an input terminal connected to a DC power supply and an output terminal connected to a load capacitor limits the inrush current that charges up the load capacitor during power up of a system. When the DC power supply applies a DC voltage to the input terminal, the inrush current control circuit produces a voltage ramp at the load capacitor instead of an abrupt DC voltage. The voltage ramp results in a constant low level current to charge up the load capacitor, greatly reducing the current drain on the DC power supply.

  20. Electronic circuits fundamentals & applications

    CERN Document Server

    Tooley, Mike

    2015-01-01

    Electronics explained in one volume, using both theoretical and practical applications.New chapter on Raspberry PiCompanion website contains free electronic tools to aid learning for students and a question bank for lecturersPractical investigations and questions within each chapter help reinforce learning Mike Tooley provides all the information required to get to grips with the fundamentals of electronics, detailing the underpinning knowledge necessary to appreciate the operation of a wide range of electronic circuits, including amplifiers, logic circuits, power supplies and oscillators. The

  1. Comparison of curative effects of traditional reconstruction plate and sacroiliac anterior cervical butterfly plate in treatment of sacroiliac joint injury%传统重建钢板与骶髂前路蝶形钢板治疗骶髂关节损伤的疗效比较

    Institute of Scientific and Technical Information of China (English)

    赵亮; 邢宏; 王劲松; 李雪松

    2015-01-01

    目的::对比传统重建钢板与骶髂前路蝶形钢板治疗骶髂关节损伤的疗效。方法:将64例患者分为观察组和对照组,每组各32例。观察组患者行骶髂前路蝶形钢板治疗,对照组患者行传统重建钢板治疗。结果:两组患者的损伤恢复优良率对比,观察组患者优于对照组(P>0.05);功能恢复、手术时间、盆骨稳定时间对比,观察组患者也好于对照组(P0. 05), and the time of function recovery, operation time, pelvic stability time were also better than those of control group (P<0. 05) with no severe complications. Conclusions:The sacroiliac anterior cervical butterfly plate in the treatment of sacroiliac joint injury has signifi-cant curative effects.

  2. A method for designing plates in treatments of proximal humeral fracture and distal radial fracture

    Directory of Open Access Journals (Sweden)

    Lin Wang

    2016-11-01

    Full Text Available The purpose of this paper was to quickly design fixation plates for fractured proximal humerus and distal radius according to the requirements of surgical treatment. Therefore, a new method to quickly design cloverleaf plate appropriate for proximal humerus and volar plate appropriate for distal radius is put forward. First, three-dimensional (3D reconstruction models of fractured proximal humerus and distal radius were generated based on deforming mean parametric models of proximal humerus and distal radius, respectively. Second, based on region-of-interest marked on the 3D reconstruction model of proximal humerus and distal radius, abutted surfaces of cloverleaf plate and volar plate were established, respectively. Then, parametric abutted surface was established after setting rational parameters for the surface of the cloverleaf plate. Parametric abutted surface of volar plate was established using the same method. Finally, parametric cloverleaf plate and volar plate are generated through thickening their respective parametric abutted surfaces. The parametric plates, acting as templates, accelerate and simplify the design process and therefore allow users to construct plate with editing valid parameters easily. Group of cloverleaf plates and volar plates with different sizes were generated quickly, showing that the proposed method is feasible and effective.

  3. Generalized Fibonacci zone plates

    CERN Document Server

    Ke, Jie; Zhu, Jianqiang

    2015-01-01

    We propose a family of zone plates which are produced by the generalized Fibonacci sequences and their axial focusing properties are analyzed in detail. Compared with traditional Fresnel zone plates, the generalized Fibonacci zone plates present two axial foci with equal intensity. Besides, we propose an approach to adjust the axial locations of the two foci by means of different optical path difference, and further give the deterministic ratio of the two focal distances which attributes to their own generalized Fibonacci sequences. The generalized Fibonacci zone plates may allow for new applications in micro and nanophotonics.

  4. ESD analog circuits and design

    CERN Document Server

    Voldman, Steven H

    2014-01-01

    A comprehensive and in-depth review of analog circuit layout, schematic architecture, device, power network and ESD design This book will provide a balanced overview of analog circuit design layout, analog circuit schematic development, architecture of chips, and ESD design.  It will start at an introductory level and will bring the reader right up to the state-of-the-art. Two critical design aspects for analog and power integrated circuits are combined. The first design aspect covers analog circuit design techniques to achieve the desired circuit performance. The second and main aspect pres

  5. Bioluminescent bioreporter integrated circuit

    Energy Technology Data Exchange (ETDEWEB)

    Simpson, Michael L. (Knoxville, TN); Sayler, Gary S. (Blaine, TN); Paulus, Michael J. (Knoxville, TN)

    2000-01-01

    Disclosed are monolithic bioelectronic devices comprising a bioreporter and an OASIC. These bioluminescent bioreporter integrated circuit are useful in detecting substances such as pollutants, explosives, and heavy-metals residing in inhospitable areas such as groundwater, industrial process vessels, and battlefields. Also disclosed are methods and apparatus for environmental pollutant detection, oil exploration, drug discovery, industrial process control, and hazardous chemical monitoring.

  6. Superconducting Quantum Circuits

    NARCIS (Netherlands)

    Majer, J.B.

    2002-01-01

    This thesis describes a number of experiments with superconducting cir- cuits containing small Josephson junctions. The circuits are made out of aluminum islands which are interconnected with a very thin insulating alu- minum oxide layer. The connections form a Josephson junction. The current trough

  7. Quantum secure circuit evaluation

    Institute of Scientific and Technical Information of China (English)

    CHEN Huanhuan; LI Bin; ZHUANG Zhenquan

    2004-01-01

    In order to solve the problem of classical secure circuit evaluation, this paper proposes a quantum approach. In this approach, the method of inserting redundant entangled particles and quantum signature has been employed to strengthen the security of the system. Theoretical analysis shows that our solution is secure against classical and quantum attacks.

  8. Afghanistan Reconstruction

    Institute of Scientific and Technical Information of China (English)

    Fu Xiaoqiang

    2006-01-01

    @@ The Karzai regime has made some progress over the past four years and a half in the post-war reconstruction.However, Taliban's destruction and drug economy are still having serious impacts on the security and stability of Afghanistan.Hence the settlement of the two problems has become a crux of affecting the country' s future.Moreover, the Karzai regime is yet to handle a series of hot potatoes in the fields of central government' s authority, military and police building-up and foreign relations as well.

  9. Paleogene plate tectonic evolution of the Arabian and Eastern Somali basins

    Digital Repository Service at National Institute of Oceanography (India)

    Royer, J.-Y.; Chaubey, A; Dyment, J.; Bhattacharya, G.C.; Srinivas, K.; Yatheesh, V.; Ramprasad, T.

    Previous models reviewed for the Paleogene tectonic evolution of the Arabian and Eastern Somali basins and present a model based on a new compilation of magnetic and gravity data. Using plate reconstructions, a self-consistent set of isochrons...

  10. 一期前路病灶清除植骨重建钛板内固定术治疗腰骶段脊柱结核%Clinical efficacy of one-stage anterior debridement, bone graft and reconstruction titanium plate internal fixation in treating lumbosacral spinal tuberculosis

    Institute of Scientific and Technical Information of China (English)

    夏曦; 唐绍锋; 曹志武; 王辉; 姚女兆; 王文军

    2016-01-01

    Objective To evaluate clinical outcomes following one-stage anterior radical debridement, interbody fusion, and reconstruction titanium plate internal fixation for the treatment of lumbosacral spinal tuberculosis.Methods The clinical data of 30 patients(17 males and 13 females,aged range from 27 to 65 years, mean 37. 5 years) with tuberculosis of the lumbosacral segments(including L5 -S1 ) who were treated with anterior radical debridement, autologous iliac bone graft,and internal fixation with reconstruction titanium plate at Department of Spinal Surgery of the First Affiliated Hospital of University of South China from August 2011 to August 2014 were retrospectively reviewed. All patients routinely received antitubercular drugs for 2 to 3 weeks before operation. Operation was performed when the general condition improved. All patients were systematically and routinely treated with antituberculous drug for 12-18 months after operation. The preoperative, 3 months after operation, last follow up erythrocyte sedimentation rate ( ESR) , C reactive protein( CRP) , visual analog scale ( VAS) , as well as Oswestry disability index ( ODI) were analyzed.Results Thirty patients were followed up for 12-36 months,mean 18 months.At last follow-up, no lower limb radiation pain and tuberculosis recurrence were found in all cases. The VAS scores were significantly decreased from 7. 8 ± 1. 7 at preoperation to 1. 7 ± 0. 6 at 3 months after operation, and 1.5±0.5 at last follow-up(all P values0.05).Conclusions Based on systemic and routine antituberculosis treatment,the surgical treatment of lumbosacral spinal tuberculosis with one-stage anterior debridement, bone graft and reconstruction titanium plate internal fixation have a direct and safe access to lesions of lumbosacral tuberculosis, and eradicate tuberculosis kitchen, reconstruct spinal stability and achieve good clinical outcome.%目的:探讨一期前路结核病灶清除植骨重建钛板内固定治疗腰骶段脊

  11. Blue Willow Story Plates

    Science.gov (United States)

    Fontes, Kris

    2009-01-01

    In the December 1997 issue of "SchoolArts" is a lesson titled "Blue Willow Story Plates" by Susan Striker. In this article, the author shares how she used this lesson with her middle-school students many times over the years. Here, she describes a Blue Willow plate painting project that her students made.

  12. Create Your Plate

    Medline Plus

    Full Text Available ... In Memory In Honor Become a Member En Español Type 1 Type 2 About Us Online Community ... Page Text Size: A A A Listen En Español Create Your Plate Create Your Plate is a ...

  13. Create Your Plate

    Medline Plus

    Full Text Available ... Diabetes Meal Plans Create Your Plate Gluten Free Diets Meal Planning for Vegetarian Diets Cook with Heart-Healthy Foods Holiday Meal Planning ... Planning Meals Diabetes Meal Plans and a Healthy Diet Create Your Plate Meal Planning for Vegetarian Diets ...

  14. Resistor Combinations for Parallel Circuits.

    Science.gov (United States)

    McTernan, James P.

    1978-01-01

    To help simplify both teaching and learning of parallel circuits, a high school electricity/electronics teacher presents and illustrates the use of tables of values for parallel resistive circuits in which total resistances are whole numbers. (MF)

  15. Electronic circuits and systems: A compilation. [including integrated circuits, logic circuits, varactor diode circuits, low pass filters, and optical equipment circuits

    Science.gov (United States)

    1975-01-01

    Technological information is presented electronic circuits and systems which have potential utility outside the aerospace community. Topics discussed include circuit components such as filters, converters, and integrators, circuits designed for use with specific equipment or systems, and circuits designed primarily for use with optical equipment or displays.

  16. Two-stage tubularized transverse preputial island flap and two-stage urethral plate reconstruction procedures in the treatment of severe hypospadias%分期管形包皮岛状皮瓣术式与分期尿道板重建卷管术式治疗重度尿道下裂的疗效比较

    Institute of Scientific and Technical Information of China (English)

    田军; 张潍平; 孙宁; 谢向辉; 李明磊; 宋宏程; 李宁; 黄澄如

    2016-01-01

    Objective To compare the treatment efficacy of severe hypospadias between two-stage urethral plate reconstruction procedure and two-stage tubularized transverse preputial island flap procedure. Methods From 2010 December to 2014 December, we retrospectively analyzed 82 cases with severe hypospadias, using two-stage urethral plate reconstruction and two-stage tubularized transverse preputial island flap urethroplasty, respectively.Their mean age in the first operation was 2.4 years, ranged from 2 to 3 years.Hypospadias were penoscrotal type in 32 cases, perineal type in 50 cases.In group A, 42 cases, including penoscrotal type in 15 cases, perineal type in 27 cases, with urethral plate reconstruction procedure underwent two-stage urethroplasty.The transected ventral penile urethral plate and to strip the ventral fibrous tissue were needed in correction of chordee of penis.The patients in group A were underwent the second urethroplasty with urethral plate reconstruction procedure 6-12 months later.In group B, 40 cases,including penoscrotal type in 17 cases, perineal type in 23 cases, who underwent one stage operation in the correction of chordee of penis, only with tubularized preputial island flap forming the part of the urethra.The patients in group B were underwent the second urethroplasty 6 ~12 months later.Results Patients were followed up for 1 to 5 years, mean 3.5 years.No recurrence of penis chordee was noticed.In group A, 6 cases (14.3%) had postoperative fistula.The second fistula repairing was perform 6 to 12 months after the second stage operation.However, still 3 cases were noticed the fistula recurrence, which was cured after the fourth operation.In group B, 3 cases (7.5%) developed fistula, which appeared in the second urethroplasty (P<0.01).They were all treated after the second repairing procedure.In group A, 4 cases were noticed urethral stricture, the urethral stricture rate was 9.5%.The stricture occurred 1 to 3 months after the second operation

  17. The LMT circuit and SPICE

    DEFF Research Database (Denmark)

    Lindberg, Erik; Murali, K.; Tamacevicius, Arunas

    2006-01-01

    The state equations of the LMT circuit are modeled as a dedicated analogue computer circuit and solved by means of PSpice. The nonlinear part of the system is studied. Problems with the PSpice program are presented.......The state equations of the LMT circuit are modeled as a dedicated analogue computer circuit and solved by means of PSpice. The nonlinear part of the system is studied. Problems with the PSpice program are presented....

  18. Behavioral synthesis of asynchronous circuits

    DEFF Research Database (Denmark)

    Nielsen, Sune Fallgaard

    2005-01-01

    This thesis presents a method for behavioral synthesis of asynchronous circuits, which aims at providing a synthesis flow which uses and tranfers methods from synchronous circuits to asynchronous circuits. We move the synchronous behavioral synthesis abstraction into the asynchronous handshake...... is idle. This reduces unnecessary switching activity in the individual functional units and therefore the energy consumption of the entire circuit. A collection of behavioral synthesis algorithms have been developed allowing the designer to perform time and power constrained design space exploration...

  19. Diode, transistor & fet circuits manual

    CERN Document Server

    Marston, R M

    2013-01-01

    Diode, Transistor and FET Circuits Manual is a handbook of circuits based on discrete semiconductor components such as diodes, transistors, and FETS. The book also includes diagrams and practical circuits. The book describes basic and special diode characteristics, heat wave-rectifier circuits, transformers, filter capacitors, and rectifier ratings. The text also presents practical applications of associated devices, for example, zeners, varicaps, photodiodes, or LEDs, as well as it describes bipolar transistor characteristics. The transistor can be used in three basic amplifier configuration

  20. Reconstruction of Space Steel Constructions

    OpenAIRE

    BRODNIANSKY, Jan; AGOCS, Zoltan; AROCH, Rudolf; SLIVANSKY, Milos

    2010-01-01

    p. 1328-1337 Reconstruction of some special types of constructions - silos, timber roof structure and a winter stadium are described. The silos are cylindrical with a diameter of 36.0m with a total height of 50.5m. The silo shell is made from steel plates of variable thickness. Capacity of the silo is 60 000t. Gradually, during more than 30 years of operation, local deformations and distinctive 6000mm high cracks in the bottom part of the shells of the silos developed. On the basis o...

  1. Statistical circuit design for yield improvement in CMOS circuits

    Science.gov (United States)

    Kamath, H. J.; Purviance, J. E.; Whitaker, S. R.

    1990-01-01

    This paper addresses the statistical design of CMOS integrated circuits for improved parametric yield. The work uses the Monte Carlo technique of circuit simulation to obtain an unbiased estimation of the yield. A simple graphical analysis tool, the yield factor histogram, is presented. The yield factor histograms are generated by a new computer program called SPICENTER. Using the yield factor histograms, the most sensitive circuit parameters are noted, and their nominal values are changed to improve the yield. Two basic CMOS example circuits, one analog and one digital, are chosen and their designs are 'centered' to illustrate the use of the yield factor histograms for statistical circuit design.

  2. Circuit Bodging: Atari Punk Console

    NARCIS (Netherlands)

    Allen, B.

    2009-01-01

    Circuit bodging is back! Maxwell is proud to present small, simple, but ultimately lovable little circuits to build for your own, personal pleasure. In this edition we are featuring: The Atari Punk Console. The Atari Punk Console (or APC) is a 555 timer IC based noise maker circuit. The original was

  3. Circuit Bodging: Atari Punk Console

    NARCIS (Netherlands)

    Allen, B.

    2009-01-01

    Circuit bodging is back! Maxwell is proud to present small, simple, but ultimately lovable little circuits to build for your own, personal pleasure. In this edition we are featuring: The Atari Punk Console. The Atari Punk Console (or APC) is a 555 timer IC based noise maker circuit. The original was

  4. Selective Manipulation of Neural Circuits.

    Science.gov (United States)

    Park, Hong Geun; Carmel, Jason B

    2016-04-01

    Unraveling the complex network of neural circuits that form the nervous system demands tools that can manipulate specific circuits. The recent evolution of genetic tools to target neural circuits allows an unprecedented precision in elucidating their function. Here we describe two general approaches for achieving circuit specificity. The first uses the genetic identity of a cell, such as a transcription factor unique to a circuit, to drive expression of a molecule that can manipulate cell function. The second uses the spatial connectivity of a circuit to achieve specificity: one genetic element is introduced at the origin of a circuit and the other at its termination. When the two genetic elements combine within a neuron, they can alter its function. These two general approaches can be combined to allow manipulation of neurons with a specific genetic identity by introducing a regulatory gene into the origin or termination of the circuit. We consider the advantages and disadvantages of both these general approaches with regard to specificity and efficacy of the manipulations. We also review the genetic techniques that allow gain- and loss-of-function within specific neural circuits. These approaches introduce light-sensitive channels (optogenetic) or drug sensitive channels (chemogenetic) into neurons that form specific circuits. We compare these tools with others developed for circuit-specific manipulation and describe the advantages of each. Finally, we discuss how these tools might be applied for identification of the neural circuits that mediate behavior and for repair of neural connections.

  5. LC-Circuit Calorimetry

    CERN Document Server

    Bossen, Olaf

    2011-01-01

    We present a new type of calorimeter in which we couple an unknown heat capacity with the aid of Peltier elements to an electrical circuit. The use of an electrical inductance and an amplifier in the circuit allows us to achieve autonomous oscillations, and the measurement of the corresponding resonance frequency makes it possible to accurately measure the heat capacity with an intrinsic statistical error that decreases as ~t^{-3/2} with measuring time t, as opposed to a corresponding error ~t^{-1/2} in the conventional alternating current (a.c.) method to measure heat capacities. We have built a demonstration experiment to show the feasibility of the new technique, and we have tested it on a gadolinium sample at its transition to the ferromagnetic state.

  6. Neuromorphic silicon neuron circuits

    Directory of Open Access Journals (Sweden)

    Giacomo eIndiveri

    2011-05-01

    Full Text Available Hardware implementations of spiking neurons can be extremely useful for a large variety of applications, ranging from high-speed modeling of large-scale neural systems to real-time behaving systems, to bidirectional brain-machine interfaces. The specific circuit solutions used to implement silicon neurons depend on the application requirements. In this paper we describe the most common building blocks and techniques used to implement these circuits, and present an overview of a wide range of neuromorphic silicon neurons, which implement different computational models, ranging from biophysically realistic and conductance based Hodgkin-Huxley models to bi-dimensional generalized adaptive Integrate and Fire models. We compare the different design methodologies used for each silicon neuron design described, and demonstrate their features with experimental results, measured from a wide range of fabricated VLSI chips.

  7. Cartography of serotonergic circuits.

    Science.gov (United States)

    Sparta, Dennis R; Stuber, Garret D

    2014-08-06

    Serotonin is an essential neuromodulator, but the precise circuit connectivity that regulates serotonergic neurons has not been well defined. Using rabies virus tracing strategies Weissbourd et al. (2014) and Pollak Dorocic et al. (2014) in this issue of Neuron and Ogawa et al. (2014) in Cell Reports provide a comprehensive map of the inputs to serotonergic neurons, highlighting the complexity and diversity of potential upstream cellular regulators. Copyright © 2014 Elsevier Inc. All rights reserved.

  8. Pixelated neutron image plates

    Science.gov (United States)

    Schlapp, M.; Conrad, H.; von Seggern, H.

    2004-09-01

    Neutron image plates (NIPs) have found widespread application as neutron detectors for single-crystal and powder diffraction, small-angle scattering and tomography. After neutron exposure, the image plate can be read out by scanning with a laser. Commercially available NIPs consist of a powder mixture of BaFBr : Eu2+ and Gd2O3 dispersed in a polymer matrix and supported by a flexible polymer sheet. Since BaFBr : Eu2+ is an excellent x-ray storage phosphor, these NIPs are particularly sensitive to ggr-radiation, which is always present as a background radiation in neutron experiments. In this work we present results on NIPs consisting of KCl : Eu2+ and LiF that were fabricated into ceramic image plates in which the alkali halides act as a self-supporting matrix without the necessity for using a polymeric binder. An advantage of this type of NIP is the significantly reduced ggr-sensitivity. However, the much lower neutron absorption cross section of LiF compared with Gd2O3 demands a thicker image plate for obtaining comparable neutron absorption. The greater thickness of the NIP inevitably leads to a loss in spatial resolution of the image plate. However, this reduction in resolution can be restricted by a novel image plate concept in which a ceramic structure with square cells (referred to as a 'honeycomb') is embedded in the NIP, resulting in a pixelated image plate. In such a NIP the read-out light is confined to the particular illuminated pixel, decoupling the spatial resolution from the optical properties of the image plate material and morphology. In this work, a comparison of experimentally determined and simulated spatial resolutions of pixelated and unstructured image plates for a fixed read-out laser intensity is presented, as well as simulations of the properties of these NIPs at higher laser powers.

  9. Changes to the shuttle circuits

    CERN Multimedia

    GS Department

    2011-01-01

    To fit with passengers expectation, there will be some changes to the shuttle circuits as from Monday 10 October. See details on http://cern.ch/ShuttleService (on line on 7 October). Circuit No. 5 is cancelled as circuit No. 1 also stops at Bldg. 33. In order to guarantee shorter travel times, circuit No. 1 will circulate on Meyrin site only and circuit No. 2, with departures from Bldg. 33 and 500, on Prévessin site only. Site Services Section

  10. Power system with an integrated lubrication circuit

    Science.gov (United States)

    Hoff, Brian D.; Akasam, Sivaprasad; Algrain, Marcelo C.; Johnson, Kris W.; Lane, William H.

    2009-11-10

    A power system includes an engine having a first lubrication circuit and at least one auxiliary power unit having a second lubrication circuit. The first lubrication circuit is in fluid communication with the second lubrication circuit.

  11. Plate removal following orthognathic surgery.

    Science.gov (United States)

    Little, Mhairi; Langford, Richard Julian; Bhanji, Adam; Farr, David

    2015-11-01

    The objectives of this study are to determine the removal rates of orthognathic plates used during orthognathic surgery at James Cook University Hospital and describe the reasons for plate removal. 202 consecutive orthognathic cases were identified between July 2004 and July 2012. Demographics and procedure details were collected for these patients. Patients from this group who returned to theatre for plate removal between July 2004 and November 2012 were identified and their notes were analysed for data including reason for plate removal, age, smoking status, sex and time to plate removal. 3.2% of plates were removed with proportionally more plates removed from the mandible than the maxilla. 10.4% of patients required removal of one or more plate. Most plates were removed within the first post-operative year. The commonest reasons for plate removal were plate exposure and infection. The plate removal rates in our study are comparable to those seen in the literature.

  12. Electric modelling and image analysis of channel flow in bipolar plates

    Energy Technology Data Exchange (ETDEWEB)

    Martin, D.; Gonzalez, L.; Garcia-Alegre, M.C.; Guinea, D. [Instituto de Automatica Industrial, Consejo Superior de Investigaciones Cientificas, 28500 Arganda, Madrid (Spain); Guinea, D.M.; Moreno, B. [Instituto de Ceramica y Vidrio, Consejo Superior de Investigaciones Cientificas, Kelsen 5, 28049 Madrid (Spain)

    2007-07-15

    Bipolar plates are an essential part of Polymer Electrolyte Membrane Fuel Cells (PEMFC) and are related to fluid conduction. The topology of a bipolar plate is critical to the homogeneous distribution of the feeding gases over the accessible zone of the electrode. An electric model that simulates flow in bipolar plates and permits the optimisation of gas feeding in PEMFCs is proposed. As a first approach, an analogy is made between the gas pressure P and an electric voltage U in a circuit and a gas flow F and an electric current I. The fluidic resistance in a bipolar plate channel is thus R=P/F and is equivalent to the electric resistance R=U/I in a branch of a circuit. Computer image processing techniques allow the validation of the present flow estimation approach based on electrical variables. Separate plates were developed to experimentally implement a complete parallel bipolar topology. (author)

  13. Anisotropic elastic plates

    CERN Document Server

    Hwu, Chyanbin

    2010-01-01

    As structural elements, anisotropic elastic plates find wide applications in modern technology. The plates here are considered to be subjected to not only in plane load but also transverse load. In other words, both plane and plate bending problems as well as the stretching-bending coupling problems are all explained in this book. In addition to the introduction of the theory of anisotropic elasticity, several important subjects have are discussed in this book such as interfaces, cracks, holes, inclusions, contact problems, piezoelectric materials, thermoelastic problems and boundary element a

  14. Plating in Top Agar

    OpenAIRE

    sprotocols

    2014-01-01

    1. Warm plates to room temperature before use. Cold plates causes the top agar to solidify irregularly. DO not warm plates to 37° as the top agar will take forever to solidify. - Prepare top agar as the appropriate liquid medium with 0.7% agar. Keeping 100 mL bottles is convenient. For phages, use λ top agar, which is less rich and yields bigger plaques. - Melt top agar in the microwave completely. Allow the agar to boil after liquification; incompletely melted agar looks liquid, but is...

  15. Biomechanical Evaluation of a Mandibular Spanning Plate Technique Compared to Standard Plating Techniques to Treat Mandibular Symphyseal Fractures

    Directory of Open Access Journals (Sweden)

    Matthew Richardson

    2015-01-01

    Full Text Available Purpose. The purpose of this study is to compare the biomechanical behavior of the spanning reconstruction plate compared to standard plating techniques for mandibular symphyseal fractures. Materials and Methods. Twenty-five human mandible replicas were used. Five unaltered synthetic mandibles were used as controls. Four experimental groups of different reconstruction techniques with five in each group were tested. Each synthetic mandible was subjected to a splaying force applied to the mandibular angle by a mechanical testing unit until the construct failed. Peak load and stiffness were recorded. The peak load and stiffness were analyzed using ANOVA and the Tukey test at a confidence level of 95% (P<0.05. Results. The two parallel plates’ group showed statistically significant lower values for peak load and stiffness compared to all other groups. No statistically significant difference was found for peak load and stiffness between the control (C group, lag screw (LS group, and the spanning plate (SP1 group. Conclusions. The spanning reconstruction plate technique for fixation of mandibular symphyseal fractures showed similar mechanical behavior to the lag screw technique when subjected to splaying forces between the mandibular gonial angles and may be considered as an alternative technique when increased reconstructive strength is needed.

  16. Breast Reconstruction with Implants

    Science.gov (United States)

    Breast reconstruction with implants Overview By Mayo Clinic Staff Breast reconstruction is a surgical procedure that restores shape to ... treat or prevent breast cancer. One type of breast reconstruction uses breast implants — silicone devices filled with silicone ...

  17. Memristor based startup circuit for self biased circuits

    Science.gov (United States)

    Das, Mangal; Singh, Amit Kumar; Rathi, Amit; Singhal, Sonal

    2016-04-01

    This paper presents the design of a Memristor based startup circuit for self biased circuits. Memristor has many advantages over conventional CMOS devices such as low leakage current at nanometer scale, easy to manufacture. In this work the switching characteristics of memristor is utilized. First the theoretical equations describing the switching behavior of memristor are investigated. To prove the switching capability of Memristor, a startup circuit based on memristor is proposed which uses series combination of Memristor and capacitor. Proposed circuit is compared with the previously reported MOSFET based startup circuits. Comparison of different circuits was done to validate the results. Simulation results show that memristor based circuit can attain on (I = 12.94 µA) to off state (I = 1 .2 µA) in 25 ns while the MOSFET based startup circuits take on (I = 14.19 µA) to off state (I = 1.4 µA) in more than 90 ns. The benefit comes in terms of area because the number of components used in the circuit are lesser than the conventional startup circuits.

  18. An equivalent circuit model for transmitting capacitive micromachined ultrasonic transducers in collapse mode.

    Science.gov (United States)

    Olcum, Selim; Yamaner, F Yalcin; Bozkurt, Ayhan; Köymen, Hayrettin; Atalar, Abdullah

    2011-07-01

    The collapse mode of operation of capacitive micromachined ultrasonic transducers (CMUTs) was shown to be a very effective way to achieve high output pressures. However, no accurate analytical or equivalent circuit model exists for understanding the mechanics and limits of the collapse mode. In this work, we develop an equivalent nonlinear electrical circuit that can accurately simulate the mechanical behavior of a CMUT with given dimensions and mechanical parameters under any large or small signal electrical excitation, including the collapse mode. The static and dynamic deflections of a plate predicted from the model are compared with finite element simulations. The equivalent circuit model can estimate the static deflection and transient behavior of a CMUT plate to within 5% accuracy. The circuit model is in good agreement with experimental results of pulse excitation applied to fabricated CMUTs. The model is suitable as a powerful design and optimization tool for collapsed and uncollapsed CMUTs.

  19. Mandibular reconstruction using stereolithographic 3-dimensional printing modeling technology.

    Science.gov (United States)

    Cohen, Adir; Laviv, Amir; Berman, Phillip; Nashef, Rizan; Abu-Tair, Jawad

    2009-11-01

    Mandibular reconstruction can be challenging for the surgeon wishing to restore its unique geometry. Reconstruction can be achieved with titanium bone plates followed by autogenous bone grafting. Incorporation of the bone graft into the mandible provides continuity and strength required for proper esthetics and function and permitting dental implant rehabilitation at a later stage. Precious time in the operating room is invested in plate contouring to reconstruct the mandible. Rapid prototyping technologies can construct physical models from computer-aided design via 3-dimensional (3D) printers. A prefabricated 3D model is achieved, which assists in accurate contouring of plates and/or planning of bone graft harvest geometry before surgery. The 2 most commonly used rapid prototyping technologies are stereolithography and 3D printing (3DP). Three-dimensional printing is advantageous to stereolithography for better accuracy, quicker printing time, and lower cost. We present 3 clinical cases based on 3DP modeling technology. Models were fabricated before the resection of mandibular ameloblastoma and were used to prepare bridging plates before the first stage of reconstruction. In 1 case, another model was fabricated and used as a template for iliac crest bone graft in the second stage of reconstruction. The 3DP technology provided a precise, fast, and cheap mandibular reconstruction, which aids in shortened operation time (and therefore decreased exposure time to general anesthesia, decreased blood loss, and shorter wound exposure time) and easier surgical procedure.

  20. Create Your Plate

    Medline Plus

    Full Text Available ... blood glucose levels and lose weight. With this method, you fill your plate with more non-starchy ... but changes the portion sizes so you are getting larger portions of non-starchy vegetables and a ...

  1. Create Your Plate

    Medline Plus

    Full Text Available ... blood glucose levels and lose weight. With this method, you fill your plate with more non-starchy ... 4/Box) Taking the guesswork out of portion control has never been easier. It can be a ...

  2. Tectonic Plate Movement.

    Science.gov (United States)

    Landalf, Helen

    1998-01-01

    Presents an activity that employs movement to enable students to understand concepts related to plate tectonics. Argues that movement brings topics to life in a concrete way and helps children retain knowledge. (DDR)

  3. MyPlate

    Science.gov (United States)

    ... our stage of life, situations, preferences, access to food, culture, traditions, and the personal decisions we make over time. All your food and beverage choices count. MyPlate offers ideas and ...

  4. Create Your Plate

    Medline Plus

    Full Text Available ... blood glucose levels and lose weight. With this method, you fill your plate with more non-starchy ... you have an easy portion control solution that works. Last Reviewed: October 8, 2015 Last Edited: September ...

  5. Designing Assemblies Of Plates

    Science.gov (United States)

    Williams, F. W.; Kennedy, D.; Butler, R.; Aston, G.; Anderson, M. S.

    1992-01-01

    VICONOPT calculates vibrations and instabilities of assemblies of prismatic plates. Designed for efficient, accurate analysis of buckling and vibration, and for optimum design of panels of composite materials. Written in FORTRAN 77.

  6. Create Your Plate

    Medline Plus

    Full Text Available ... Your Plate Gluten Free Diets Meal Planning for Vegetarian Diets Cook with Heart-Healthy Foods Holiday Meal Planning What Can I Eat? Making Healthy Food Choices Diabetes Superfoods Non-starchy Vegetables Grains and Starchy Vegetables ...

  7. Create Your Plate

    Medline Plus

    Full Text Available ... Recipes Association Cookbook Recipes Planning Meals Diabetes Meal Plans Create Your Plate Gluten Free Diets Meal Planning ... serving of dairy or both as your meal plan allows. Choose healthy fats in small amounts. For ...

  8. Create Your Plate

    Medline Plus

    Full Text Available ... 1 Diabetes Get Started Safely Get And Stay Fit Types of Activity Weight Loss Assess Your Lifestyle ... manage portion control wherever you are. Now, our best-selling, sectioned to-go plate with easy-sealing ...

  9. Create Your Plate

    Medline Plus

    Full Text Available ... Plate is a simple and effective way to manage your blood glucose levels and lose weight. With ... been easier. It can be a challenge to manage portion control wherever you are. Now, our best- ...

  10. Tectonic Plate Movement.

    Science.gov (United States)

    Landalf, Helen

    1998-01-01

    Presents an activity that employs movement to enable students to understand concepts related to plate tectonics. Argues that movement brings topics to life in a concrete way and helps children retain knowledge. (DDR)

  11. Create Your Plate

    Medline Plus

    Full Text Available ... Carbohydrates Carbohydrate Counting Make Your Carbs Count Glycemic ... to manage portion control wherever you are. Now, our best-selling, sectioned to-go plate with easy-sealing ...

  12. Does plate type influence the clinical outcomes and implant removal in midclavicular fractures fixed with 2.7-mm anteroinferior plates? A retrospective cohort study.

    Science.gov (United States)

    Gilde, Alex K; Jones, Clifford B; Sietsema, Debra L; Hoffmann, Martin F

    2014-07-04

    The purpose of this study was to evaluate surgical healing rates, implant failure, implant removal, and the need for surgical revision with regards to plate type in midshaft clavicle fractures fixed with 2.7-mm anteroinferior plates utilizing modern plating techniques. This retrospective exploratory cohort review took place at a level I teaching trauma center and a single large private practice office. A total of 155 skeletally mature individuals with 156 midshaft clavicle fractures between March 2002 and March 2012 were included in the final results. Fractures were identified by mechanism of injury and classified based on OTA/AO criteria. All fractures were fixed with 2.7-mm anteroinferior plates. Primary outcome measurements included implant failure, malunion, nonunion, and implant removal. Secondary outcome measurements included pain with the visual analog scale and range of motion. Statistically significant testing was set at 0.05, and testing was performed using chi-square, Fisher's exact, Mann-Whitney U, and Kruskall-Wallis. Implant failure occurred more often in reconstruction plates as compared to dynamic compression plates (p = 0.029). Malunions and nonunions occurred more often in fractures fixed with reconstruction plates as compared to dynamic compression plates, but it was not statistically significant. Implant removal attributed to irritation or implant prominence was observed in 14 patients. Statistically significant levels of pain were seen in patients requiring implant removal (p = 0.001) but were not associated with the plate type. Anteroinferior clavicular fracture fixation with 2.7-mm dynamic compression plates results in excellent healing rates with low removal rates in accordance with the published literature. Given higher rates of failure, 2.7-mm reconstruction plates should be discouraged in comparison to stiffer and more reliable 2.7-mm dynamic compression plates.

  13. Reconstructive Urology

    Directory of Open Access Journals (Sweden)

    Fikret Fatih Önol

    2014-11-01

    Full Text Available In the treatment of urethral stricture, Buccal Mucosa Graft (BMG and reconstruction is applied with different patch techniques. Recently often prefered, this approach is, in bulber urethra strictures of BMG’s; by “ventral onley”, in pendulous urethra because of thinner spingiosis body, which provides support and nutrition of graft; by means of “dorsal inley” being anastomosis. In the research that Cordon et al. did, they compared conventional BMJ “onley” urethroplast and “pseudo-spongioplasty” which base on periurethral vascular tissues to be nourished by closing onto graft. In repairment of front urethras that spongiosis supportive tissue is insufficient, this method is defined as peripheral dartos [çevre dartos?] and buck’s fascia being mobilized and being combined on BMG patch. Between the years 2007 and 2012, assessment of 56 patients with conventional “ventral onley” BMG urethroplast and 46 patients with “pseudo-spongioplasty” were reported to have similar success rates (80% to 84% in 3.5 year follow-up on average. While 74% of the patients that were applied pseudo-spongioplasty had disease present at distal urethra (pendulous, bulbopendulous, 82% of the patients which were applied conventional onley urethroplast had stricture at proximal (bulber urethra yet. Also lenght of the stricture at the pseudo-spongioplasty group was longer in a statistically significant way (5.8 cm to 4.7 cm on average, p=0.028. This study which Cordon et al. did, shows that conditions in which conventional sponjiyoplasti is not possible, periurethral vascular tissues are adequate to nourish BMG. Even it is an important technique in terms of bringing a new point of view to today’s practice, data especially about complications that may show up after pseudo-spongioplasty usage on long distal strictures (e.g. appearance of urethral diverticulum is not reported. Along with this we think that, providing an oppurtinity to patch directly

  14. Origami - Folded Plate Structures

    OpenAIRE

    Buri, Hans Ulrich

    2010-01-01

    This research investigates new methods of designing folded plate structures that can be built with cross-laminated timber panels. Folded plate structures are attractive to both architects and engineers for their structural, spatial, and plastic qualities. Thin surfaces can be stiffened by a series of folds, and thus not only cover space, but also act as load bearing elements. The variation of light and shadow along the folded faces emphasizes the plas...

  15. Fractal multifiber microchannel plates

    Science.gov (United States)

    Cook, Lee M.; Feller, W. B.; Kenter, Almus T.; Chappell, Jon H.

    1992-01-01

    The construction and performance of microchannel plates (MCPs) made using fractal tiling mehtods are reviewed. MCPs with 40 mm active areas having near-perfect channel ordering were produced. These plates demonstrated electrical performance characteristics equivalent to conventionally constructed MCPs. These apparently are the first MCPs which have a sufficiently high degree of order to permit single channel addressability. Potential applications for these devices and the prospects for further development are discussed.

  16. Reconstruction of soft plate necrosis after endotracheal intubation.

    Science.gov (United States)

    Lee, Hyuck Jae; Lim, So Young; Pyon, Jai-Kyong; Mun, Goo Hyun; Bang, Sa Ik; Oh, Kap Sung

    2014-01-01

    Uvular necrosis after long-term endotracheal intubation has been previously reported, but there have been no reports regarding soft palate necrosis after endotracheal intubation. Recently, we encountered 2 patients who had a high degree of soft palate necrosis following endotracheal intubation during long-term care in the intensive care unit. This study reports noncongenital soft palate cleft caused by endotracheal intubation. Two patients, aged 30 and 38 years, with noncongenital cleft palate were treated with pharyngeal flap and/or palatoplasty at our institution from March 2011 to May 2013. Initially, the patients complained of acquired speech disorder and severe oronasal regurgitation caused by a palatal defect. Speech ability was evaluated preoperatively and postoperatively by a perceptual language test and nasopharyngoscopy. The cleft soft palates of both patients were completely repaired, and the aforementioned symptoms improved after surgery. Postoperative courses were uneventful in both of the cases, and neither patient experienced a recurrence. Although rare, long-term intensive care unit care with endotracheal intubation can cause noncongenital soft palate cleft. In cases with iatrogenic cleft palate that does not heal with conservative treatment, surgical procedures such as pharyngeal flap and palatoplasty can be helpful.

  17. Upgrade of Tuning-position Display for SFC 200 kW Transmitter Anode Circuit

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    It is necessary to display of precise position of anode plate tuning device for 200 kW transmitter.Therefore parameters can be conveniently preset in different frequency to tealize frequency replacing and impedance matching of D-circuit.Photo-electricity coding was originally used for angle position of old system.But after ten years’operation,it can’t precisely display position of circuit element movement because its grating was

  18. Kinematics of a former oceanic plate of the Neotethys revealed by deformation in the Ulukışla basin (Turkey)

    NARCIS (Netherlands)

    Gürer, Derya|info:eu-repo/dai/nl/373437684; van Hinsbergen, Douwe J J; Matenco, Liviu|info:eu-repo/dai/nl/163604592; Corfu, Fernando; Cascella, Antonio

    2016-01-01

    Kinematic reconstruction of modern ocean basins shows that since Pangea breakup a vast area in the Neotethyan realm was lost to subduction. Here we develop a first-order methodology to reconstruct the kinematic history of the lost plates of the Neotethys, using records of subducted plates accreted

  19. Kinematics of a former oceanic plate of the Neotethys revealed by deformation in the Ulukışla basin (Turkey)

    NARCIS (Netherlands)

    Gürer, Derya; van Hinsbergen, Douwe J J; Matenco, Liviu; Corfu, Fernando; Cascella, Antonio

    2016-01-01

    Kinematic reconstruction of modern ocean basins shows that since Pangea breakup a vast area in the Neotethyan realm was lost to subduction. Here we develop a first-order methodology to reconstruct the kinematic history of the lost plates of the Neotethys, using records of subducted plates accreted t

  20. Near-Field Acoustic Holography of Chladni Plate

    Science.gov (United States)

    Kim, Hyunhee; Kim, Yunbog; Jeon, Dongryul

    2007-03-01

    Characteristic modes of a Chladni plate can be visualized by sand gathering along the nodal lines. Although one can view two-dimensional vibration patterns, the sand pattern does not show a bending of antinode. We used near-field acoustic holography to reconstruct a three-dimensional image of circular and rectangular Chladni plates. The sound pressure was measured using four scanning microphones located 3 mm above a Chladni plate. A reference microphone was placed close to a speaker which drives the plate. A total of 60x60 data were collected from 30x30 cm^2 area and processed using MATLAB in accordance with the algorithm of near-field acoustic holography. The three-dimensional graphic image of the vibrating plate reconstructed this way not only matched the sand pattern but also visualized the bending of the plate. Propagation of the sound pressure could be also visualized three-dimensionally. The plot of sound pressure against the distance showed the 1/distance^2 dependence as expected. Sound is a difficult subject in physics class because it is invisible. Our results demonstrate that near-field acoustic holography combined with computer graphic is an effective tool to visualize the generation of a sound.

  1. Simulation of the CMS Resistive Plate Chambers

    CERN Document Server

    Hadjiiska, R; Pavlov, B; Petkov, P; Dimitrov, A; Beernaert, K; Cimmino, A; Costantini, S; Garcia, G; Lellouch, J; Marinov, A; Ocampo, A; Strobbe, N; Thyssen, F; Tytgat, M; Verwilligen, P; Yazgan, E; Zaganidis, N; Aleksandrov, A; Genchev, V; Iaydjiev, P; Rodozov, M; Shopova, M; Sultanov, G; Ban, Y; Cai, J; Xue, Z; Ge, Y; Li, Q; Qian, S; Avila, C; Chaparro, L F; Gomez, J P; Moreno, B Gomez; Oliveros, A F Osorio; Sanabria, J C; Assran, Y; Sharma, A; Abbrescia, M; Colaleo, A; Pugliese, G; Loddo, F; Calabria, C; Maggi, M; Benussi, L; Bianco, S; Colafranceschi, S; Piccolo, D; Carrillo, C; Iorio, O; Buontempo, S; Paolucci, P; Vitulo, P; Berzano, U; Gabusi, M; Kang, M; Lee, K S; Park, S K; Shin, S; Kim, M S; Seo, H; Goh, J; Choi, Y; Shoaib, M

    2013-01-01

    The Resistive Plate Chamber (RPC) muon subsystem contributes significantly to the formation of the trigger decision and reconstruction of the muon trajectory parameters. Simulation of the RPC response is a crucial part of the entire CMS Monte Carlo software and directly influences the final physical results. An algorithm based on the parametrization of RPC efficiency, noise, cluster size and timing for every strip has been developed. Experimental data obtained from cosmic and proton-proton collisions at $\\sqrt{s}=7$ TeV have been used for determination of the parameters. A dedicated validation procedure has been developed. A good agreement between the simulated and experimental data has been achieved.

  2. Flexible circuits with integrated switches for robotic shape sensing

    Science.gov (United States)

    Harnett, C. K.

    2016-05-01

    Digital switches are commonly used for detecting surface contact and limb-position limits in robotics. The typical momentary-contact digital switch is a mechanical device made from metal springs, designed to connect with a rigid printed circuit board (PCB). However, flexible printed circuits are taking over from the rigid PCB in robotics because the circuits can bend while carrying signals and power through moving joints. This project is motivated by a previous work where an array of surface-mount momentary contact switches on a flexible circuit acted as an all-digital shape sensor compatible with the power resources of energy harvesting systems. Without a rigid segment, the smallest commercially-available surface-mount switches would detach from the flexible circuit after several bending cycles, sometimes violently. This report describes a low-cost, conductive fiber based method to integrate electromechanical switches into flexible circuits and other soft, bendable materials. Because the switches are digital (on/off), they differ from commercially-available continuous-valued bend/flex sensors. No amplification or analog-to-digital conversion is needed to read the signal, but the tradeoff is that the digital switches only give a threshold curvature value. Boundary conditions on the edges of the flexible circuit are key to setting the threshold curvature value for switching. This presentation will discuss threshold-setting, size scaling of the design, automation for inserting a digital switch into the flexible circuit fabrication process, and methods for reconstructing a shape from an array of digital switch states.

  3. Vibration and Buckling of Web Plate of the Plate Girder

    OpenAIRE

    高橋, 和雄; 呉, 明強; 中澤, 聡志; 筑紫, 宏之

    1998-01-01

    The vibration and buckling of the web of the plate girder are studied in this paper. The small deflection theory of the thin plate is used. The finite strip method is employed to solve vibration and buckling of the plate girder. Natural frequenies of buckling properties are shown for various plate girder bridges.

  4. Electric circuits problem solver

    CERN Document Server

    REA, Editors of

    2012-01-01

    Each Problem Solver is an insightful and essential study and solution guide chock-full of clear, concise problem-solving gems. All your questions can be found in one convenient source from one of the most trusted names in reference solution guides. More useful, more practical, and more informative, these study aids are the best review books and textbook companions available. Nothing remotely as comprehensive or as helpful exists in their subject anywhere. Perfect for undergraduate and graduate studies.Here in this highly useful reference is the finest overview of electric circuits currently av

  5. Linear integrated circuits

    CERN Document Server

    Carr, Joseph

    1996-01-01

    The linear IC market is large and growing, as is the demand for well trained technicians and engineers who understand how these devices work and how to apply them. Linear Integrated Circuits provides in-depth coverage of the devices and their operation, but not at the expense of practical applications in which linear devices figure prominently. This book is written for a wide readership from FE and first degree students, to hobbyists and professionals.Chapter 1 offers a general introduction that will provide students with the foundations of linear IC technology. From chapter 2 onwa

  6. Optoelectronics circuits manual

    CERN Document Server

    Marston, R M

    1999-01-01

    This manual is a useful single-volume guide specifically aimed at the practical design engineer, technician, and experimenter, as well as the electronics student and amateur. It deals with the subject in an easy to read, down to earth, and non-mathematical yet comprehensive manner, explaining the basic principles and characteristics of the best known devices, and presenting the reader with many practical applications and over 200 circuits. Most of the ICs and other devices used are inexpensive and readily available types, with universally recognised type numbers.The second edition

  7. Nano integrated circuit process

    Energy Technology Data Exchange (ETDEWEB)

    Yoon, Yung Sup

    2004-02-15

    This book contains nine chapters, which are introduction of manufacture of semiconductor chip, oxidation such as Dry-oxidation, wet oxidation, oxidation model and oxide film, diffusion like diffusion process, diffusion equation, diffusion coefficient and diffusion system, ion implantation, including ion distribution, channeling, multiimplantation and masking and its system, sputtering such as CVD and PVD, lithography, wet etch and dry etch, interconnection and flattening like metal-silicon connection, silicide, multiple layer metal process and flattening, an integrated circuit process, including MOSFET and CMOS.

  8. Photonic Integrated Circuits

    Science.gov (United States)

    Krainak, Michael; Merritt, Scott

    2016-01-01

    Integrated photonics generally is the integration of multiple lithographically defined photonic and electronic components and devices (e.g. lasers, detectors, waveguides passive structures, modulators, electronic control and optical interconnects) on a single platform with nanometer-scale feature sizes. The development of photonic integrated circuits permits size, weight, power and cost reductions for spacecraft microprocessors, optical communication, processor buses, advanced data processing, and integrated optic science instrument optical systems, subsystems and components. This is particularly critical for small spacecraft platforms. We will give an overview of some NASA applications for integrated photonics.

  9. Electronic logic circuits

    CERN Document Server

    Gibson, J

    2013-01-01

    Most branches of organizing utilize digital electronic systems. This book introduces the design of such systems using basic logic elements as the components. The material is presented in a straightforward manner suitable for students of electronic engineering and computer science. The book is also of use to engineers in related disciplines who require a clear introduction to logic circuits. This third edition has been revised to encompass the most recent advances in technology as well as the latest trends in components and notation. It includes a wide coverage of application specific integrate

  10. Electronics circuits and systems

    CERN Document Server

    Bishop, Owen

    2011-01-01

    The material in Electronics - Circuits and Systems is a truly up-to-date textbook, with coverage carefully matched to the electronics units of the 2007 BTEC National Engineering and the latest AS and A Level specifications in Electronics from AQA, OCR and WJEC. The material has been organized with a logical learning progression, making it ideal for a wide range of pre-degree courses in electronics. The approach is student-centred and includes: numerous examples and activities; web research topics; Self Test features, highlighted key facts, formulae and definitions. Ea

  11. Electronics circuits and systems

    CERN Document Server

    Bishop, Owen

    2007-01-01

    The material in Electronics - Circuits and Systems is a truly up-to-date textbook, with coverage carefully matched to the electronics units of the 2007 BTEC National Engineering and the latest AS and A Level specifications in Electronics from AQA, OCR and WJEC. The material has been organized with a logical learning progression, making it ideal for a wide range of pre-degree courses in electronics. The approach is student-centred and includes: numerous examples and activities; web research topics; Self Test features, highlighted key facts, formulae and definitions. Each chapter ends with a set

  12. Sequential circuit design for radiation hardened multiple voltage integrated circuits

    Science.gov (United States)

    Clark, Lawrence T.; McIver, III, John K.

    2009-11-24

    The present invention includes a radiation hardened sequential circuit, such as a bistable circuit, flip-flop or other suitable design that presents substantial immunity to ionizing radiation while simultaneously maintaining a low operating voltage. In one embodiment, the circuit includes a plurality of logic elements that operate on relatively low voltage, and a master and slave latches each having storage elements that operate on a relatively high voltage.

  13. 49 CFR 236.13 - Spring switch; selection of signal control circuits through circuit controller.

    Science.gov (United States)

    2010-10-01

    ... circuits through circuit controller. 236.13 Section 236.13 Transportation Other Regulations Relating to...; selection of signal control circuits through circuit controller. The control circuits of signals governing... circuit controller, or through the contacts of relay repeating the position of such circuit...

  14. Development of site-specific locking plates for acetabular fractures.

    Science.gov (United States)

    Xu, Meng; Zhang, Li-Hai; Zhang, Ying-Ze; He, Chun-Qing; Zhang, Li-Cheng; Wang, Yan; Tang, Pei-Fu

    2013-05-01

    Site-specific locking plates have gained popularity for the treatment of fractures. However, the clinical use of a site-specific locking plate for acetabular fractures remains untested due to production limits. To design a universal site-specific locking plate for acetabular fractures, the 3-dimensional (3D) photographic records of 171 pelvises were retrospectively studied to generate a universal posterior innominate bone surface. Using 3D photographical processing software, the 3D coordinate system was reset according to bony landmarks and was scaled based on the acetabular diameter to allow a direct comparison between surfaces. The measured surface was separated into measurement units. At each measurement unit, the authors calculated the average z-axis values in all samples and obtained the 3D coordinate values of the point cloud that could be reconstructed into the universal surface. A plate was subsequently designed in 3D photographical processing software, and the orientation and distribution of locking screws was included. To manufacture a plate, the data were entered into Unigraphics NX version 6.0 software (Siemens PLM Software, Co, Ltd, Plano, Texas) and a CNC digital milling machine (FANUC Co, Ltd, Yamanashi, Japan). The resulting locking plate fit excellently with the reduced bone surface intraoperatively. Plate contouring was avoided intraoperatively. Universal 3.5-mm locking screws locked successfully into the plate, and their orientations were consistent with the design. No screw yielded to acetabular penetration. This method of designing a site-specific acetabular locking plate is practical, and the plates are suitable for clinical use. These site-specific locking plates may be an option for the treatment of acetabular fractures, particularly in elderly patients.

  15. Quasi-Linear Circuit

    Science.gov (United States)

    Bradley, William; Bird, Ross; Eldred, Dennis; Zook, Jon; Knowles, Gareth

    2013-01-01

    This work involved developing spacequalifiable switch mode DC/DC power supplies that improve performance with fewer components, and result in elimination of digital components and reduction in magnetics. This design is for missions where systems may be operating under extreme conditions, especially at elevated temperature levels from 200 to 300 degC. Prior art for radiation-tolerant DC/DC converters has been accomplished utilizing classical magnetic-based switch mode converter topologies; however, this requires specific shielding and component de-rating to meet the high-reliability specifications. It requires complex measurement and feedback components, and will not enable automatic re-optimization for larger changes in voltage supply or electrical loading condition. The innovation is a switch mode DC/DC power supply that eliminates the need for processors and most magnetics. It can provide a well-regulated voltage supply with a gain of 1:100 step-up to 8:1 step down, tolerating an up to 30% fluctuation of the voltage supply parameters. The circuit incorporates a ceramic core transformer in a manner that enables it to provide a well-regulated voltage output without use of any processor components or magnetic transformers. The circuit adjusts its internal parameters to re-optimize its performance for changes in supply voltage, environmental conditions, or electrical loading at the output

  16. Automated Design of Quantum Circuits

    Science.gov (United States)

    Williams, Colin P.; Gray, Alexander G.

    2000-01-01

    In order to design a quantum circuit that performs a desired quantum computation, it is necessary to find a decomposition of the unitary matrix that represents that computation in terms of a sequence of quantum gate operations. To date, such designs have either been found by hand or by exhaustive enumeration of all possible circuit topologies. In this paper we propose an automated approach to quantum circuit design using search heuristics based on principles abstracted from evolutionary genetics, i.e. using a genetic programming algorithm adapted specially for this problem. We demonstrate the method on the task of discovering quantum circuit designs for quantum teleportation. We show that to find a given known circuit design (one which was hand-crafted by a human), the method considers roughly an order of magnitude fewer designs than naive enumeration. In addition, the method finds novel circuit designs superior to those previously known.

  17. Large-scale circuit simulation

    Science.gov (United States)

    Wei, Y. P.

    1982-12-01

    The simulation of VLSI (Very Large Scale Integration) circuits falls beyond the capabilities of conventional circuit simulators like SPICE. On the other hand, conventional logic simulators can only give the results of logic levels 1 and 0 with the attendent loss of detail in the waveforms. The aim of developing large-scale circuit simulation is to bridge the gap between conventional circuit simulation and logic simulation. This research is to investigate new approaches for fast and relatively accurate time-domain simulation of MOS (Metal Oxide Semiconductors), LSI (Large Scale Integration) and VLSI circuits. New techniques and new algorithms are studied in the following areas: (1) analysis sequencing (2) nonlinear iteration (3) modified Gauss-Seidel method (4) latency criteria and timestep control scheme. The developed methods have been implemented into a simulation program PREMOS which could be used as a design verification tool for MOS circuits.

  18. Integrated circuit cooled turbine blade

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Ching-Pang; Jiang, Nan; Um, Jae Y.; Holloman, Harry; Koester, Steven

    2017-08-29

    A turbine rotor blade includes at least two integrated cooling circuits that are formed within the blade that include a leading edge circuit having a first cavity and a second cavity and a trailing edge circuit that includes at least a third cavity located aft of the second cavity. The trailing edge circuit flows aft with at least two substantially 180-degree turns at the tip end and the root end of the blade providing at least a penultimate cavity and a last cavity. The last cavity is located along a trailing edge of the blade. A tip axial cooling channel connects to the first cavity of the leading edge circuit and the penultimate cavity of the trailing edge circuit. At least one crossover hole connects the penultimate cavity to the last cavity substantially near the tip end of the blade.

  19. CMOS Nonlinear Signal Processing Circuits

    OpenAIRE

    2010-01-01

    The chapter describes various nonlinear signal processing CMOS circuits, including a high reliable WTA/LTA, simple MED cell, and low-voltage arbitrary order extractor. We focus the discussion on CMOS analog circuit design with reliable, programmable capability, and low voltage operation. It is a practical problem when the multiple identical cells are required to match and realized within a single chip using a conventional process. Thus, the design of high-reliable circuit is indeed needed. Th...

  20. Analog electronic neural network circuits

    Energy Technology Data Exchange (ETDEWEB)

    Graf, H.P.; Jackel, L.D. (AT and T Bell Labs., Holmdel, NJ (USA))

    1989-07-01

    The large interconnectivity and moderate precision required in neural network models present new opportunities for analog computing. This paper discusses analog circuits for a variety of problems such as pattern matching, optimization, and learning. Most of the circuits build so far are relatively small, exploratory designs. The most mature circuits are those for template matching. Chips performing this function are now being applied to pattern recognition problems.

  1. Bending and stretching of plates

    CERN Document Server

    Mansfield, E H; Hemp, W S

    1964-01-01

    The Bending and Stretching of Plates deals with elastic plate theory, particularly on small- and large-deflexion theory. Small-deflexion theory concerns derivation of basic equations, rectangular plates, plates of various shapes, plates whose boundaries are amenable to conformal transformation, plates with variable rigidity, and approximate methods. Large-deflexion theory includes general equations and some exact solutions, approximate methods in large-deflexion theory, asymptotic large-deflexion theories for very thin plates. Asymptotic theories covers membrane theory, tension field theory, a

  2. Subduction controls the distribution and fragmentation of Earth’s tectonic plates.

    Science.gov (United States)

    Mallard, Claire; Coltice, Nicolas; Seton, Maria; Müller, R Dietmar; Tackley, Paul J

    2016-07-07

    The theory of plate tectonics describes how the surface of Earth is split into an organized jigsaw of seven large plates of similar sizes and a population of smaller plates whose areas follow a fractal distribution. The reconstruction of global tectonics during the past 200 million years suggests that this layout is probably a long-term feature of Earth, but the forces governing it are unknown. Previous studies, primarily based on the statistical properties of plate distributions, were unable to resolve how the size of the plates is determined by the properties of the lithosphere and the underlying mantle convection. Here we demonstrate that the plate layout of Earth is produced by a dynamic feedback between mantle convection and the strength of the lithosphere. Using three-dimensional spherical models of mantle convection that self-consistently produce the plate size–frequency distribution observed for Earth, we show that subduction geometry drives the tectonic fragmentation that generates plates. The spacing between the slabs controls the layout of large plates, and the stresses caused by the bending of trenches break plates into smaller fragments. Our results explain why the fast evolution in small back-arc plates reflects the marked changes in plate motions during times of major reorganizations. Our study opens the way to using convection simulations with plate-like behaviour to unravel how global tectonics and mantle convection are dynamically connected.

  3. On the Enigmatic Birth of the Pacific Plate within the Panthalassa Ocean

    Science.gov (United States)

    Boschman, L.; Van Hinsbergen, D. J. J.

    2016-12-01

    The oceanic Pacific Plate started forming in Early Jurassic time within the vast Panthalassa Ocean that surrounded the supercontinent Pangea and contains the oldest lithosphere that can directly constrain the geodynamic history of the circum-Pangean Earth. Here, we show that the geometry of the oldest marine magnetic anomalies of the Pacific Plate attests of a unique plate kinematic event that sparked the plate's birth in virtually a point location, surrounded by the Izanagi, Farallon and Phoenix Plates. We reconstruct the unstable triple junction that caused the plate reorganization leading to the birth of the Pacific Plate and present a model of the plate tectonic configuration that preconditioned this event. We show that a stable, but migrating triple junction involving the gradual cessation of intra-oceanic Panthalassa subduction culminated in the formation of an unstable transform-transform-transform triple junction. The consequent plate boundary reorganization resulted in the formation of a stable triangular three-ridge system from which the nascent Pacific Plate expanded. We link the birth of the Pacific Plate to the regional termination of intra-Panthalassa subduction. Remnants thereof have been identified in the deep lower mantle of which the locations may provide paleolongitudinal control on the absolute location of the early Pacific Plate. Our results constitute an essential step in unraveling the plate tectonic evolution of `Thalassa Incognita' comprising the comprehensive Panthalassa Ocean surrounding Pangea.

  4. Subduction controls the distribution and fragmentation of Earth’s tectonic plates

    Science.gov (United States)

    Mallard, Claire; Coltice, Nicolas; Seton, Maria; Müller, R. Dietmar; Tackley, Paul J.

    2016-07-01

    The theory of plate tectonics describes how the surface of Earth is split into an organized jigsaw of seven large plates of similar sizes and a population of smaller plates whose areas follow a fractal distribution. The reconstruction of global tectonics during the past 200 million years suggests that this layout is probably a long-term feature of Earth, but the forces governing it are unknown. Previous studies, primarily based on the statistical properties of plate distributions, were unable to resolve how the size of the plates is determined by the properties of the lithosphere and the underlying mantle convection. Here we demonstrate that the plate layout of Earth is produced by a dynamic feedback between mantle convection and the strength of the lithosphere. Using three-dimensional spherical models of mantle convection that self-consistently produce the plate size-frequency distribution observed for Earth, we show that subduction geometry drives the tectonic fragmentation that generates plates. The spacing between the slabs controls the layout of large plates, and the stresses caused by the bending of trenches break plates into smaller fragments. Our results explain why the fast evolution in small back-arc plates reflects the marked changes in plate motions during times of major reorganizations. Our study opens the way to using convection simulations with plate-like behaviour to unravel how global tectonics and mantle convection are dynamically connected.

  5. Transistor switching and sequential circuits

    CERN Document Server

    Sparkes, John J

    1969-01-01

    Transistor Switching and Sequential Circuits presents the basic ideas involved in the construction of computers, instrumentation, pulse communication systems, and automation. This book discusses the design procedure for sequential circuits. Organized into two parts encompassing eight chapters, this book begins with an overview of the ways on how to generate the types of waveforms needed in digital circuits, principally ramps, square waves, and delays. This text then considers the behavior of some simple circuits, including the inverter, the emitter follower, and the long-tailed pair. Other cha

  6. Unstable oscillators based hyperchaotic circuit

    DEFF Research Database (Denmark)

    Murali, K.; Tamasevicius, A.; G. Mykolaitis, A.;

    1999-01-01

    A simple 4th order hyperchaotic circuit with unstable oscillators is described. The circuit contains two negative impedance converters, two inductors, two capacitors, a linear resistor and a diode. The Lyapunov exponents are presented to confirm hyperchaotic nature of the oscillations in the circ......A simple 4th order hyperchaotic circuit with unstable oscillators is described. The circuit contains two negative impedance converters, two inductors, two capacitors, a linear resistor and a diode. The Lyapunov exponents are presented to confirm hyperchaotic nature of the oscillations...

  7. Impact of Inert Metal Particles Flow on Aluminium Plate

    Institute of Scientific and Technical Information of China (English)

    WANG Zhongqi; LIU Yi; CHEN Yahong; BAI Chunhua

    2008-01-01

    Inert metal explosive, a new kind of explosive, is a mixture of high explosive and inert metal particle.When this kind of explosive is detonated, an inert metal particle flow will be formed by the explosive product driving.To determine the characteristics of the movement of the metal particle flow, a series of aluminium plates were designed to be the targets on which the metal particle flow impacted.The test result was presented and a numerical model was set up to analyze the impact of the high speed inert metal particles on aluminium plate.Based on the numerical analysis, the relationship between the characteristic of the mark on the target plate and the initial condition of the inert metal particles was proposed.From the analysis of the impact on target plates, more information about the movement of the metal particles could be reconstructed.

  8. Hybrid Method for Tokamak MHD Equilibrium Configuration Reconstruction

    Institute of Scientific and Technical Information of China (English)

    HE Hong-Da; DONG Jia-Qi; ZHANG Jin-Hua; JIANG Hai-Bin

    2007-01-01

    A hybrid method for tokamak MHD equilibrium configuration reconstruction is proposed and employed in the modified EFIT code. This method uses the free boundary tokamak equilibrium configuration reconstruction algorithm with one boundary point fixed. The results show that the position of the fixed point has explicit effects on the reconstructed divertor configurations. In particular, the separatrix of the reconstructed divertor configuration precisely passes the required position when the hybrid method is used in the reconstruction. The profiles of plasma parameters such as pressure and safety factor for reconstructed HL-2A tokamak configurations with the hybrid and the free boundary methods are compared. The possibility for applications of the method to swing the separatrix strike point on the divertor target plate is discussed.

  9. A Circuit to Demonstrate Phase Relationships in "RLC" Circuits

    Science.gov (United States)

    Sokol, P. E.; Warren, G.; Zheng, B.; Smith, P.

    2013-01-01

    We have developed a circuit to demonstrate the phase relationships between resistive and reactive elements in series "RLC" circuits. We utilize a differential amplifier to allow the phases of the three elements and the current to be simultaneously displayed on an inexpensive four channel oscilloscope. We have included a novel circuit…

  10. Anterior cervical plating

    Directory of Open Access Journals (Sweden)

    Gonugunta V

    2005-01-01

    Full Text Available Although anterior cervical instrumentation was initially used in cervical trauma, because of obvious benefits, indications for its use have been expanded over time to degenerative cases as well as tumor and infection of the cervical spine. Along with a threefold increase in incidence of cervical fusion surgery, implant designs have evolved over the last three decades. Observation of graft subsidence and phenomenon of stress shielding led to the development of the new generation dynamic anterior cervical plating systems. Anterior cervical plating does not conclusively improve clinical outcome of the patients, but certainly enhances the efficacy of autograft and allograft fusion and lessens the rate of pseudoarthrosis and kyphosis after multilevel discectomy and fusions. A review of biomechanics, surgical technique, indications, complications and results of various anterior cervical plating systems is presented here to enable clinicians to select the appropriate construct design.

  11. Repair of ectopia cordis using a resorbable poly-L-lactic-polyglycolic acid plate in a patient with pentalogy of Cantrell.

    Science.gov (United States)

    Chia, Hui-Ling; Rasheed, Mohamed Zulfikar; Ong, Kim-Kiat; Yeow, Vincent Kok-Leng

    2012-06-01

    We present a case of a 10-month-old male infant with thoracoabdominal ectopia cordis, as part of Cantrell pentad, repaired using a poly-L-lactic-polyglycolic acid plate, a resorbable plating system widely used in craniomaxillofacial reconstruction. This is the first reported case of sternal reconstruction using a poly-L-lactic-polyglycolic acid plate. The repair was successfully carried out without cardiopulmonary compromise and good aesthetic outcome was achieved.

  12. VLSI circuits implementing computational models of neocortical circuits.

    Science.gov (United States)

    Wijekoon, Jayawan H B; Dudek, Piotr

    2012-09-15

    This paper overviews the design and implementation of three neuromorphic integrated circuits developed for the COLAMN ("Novel Computing Architecture for Cognitive Systems based on the Laminar Microcircuitry of the Neocortex") project. The circuits are implemented in a standard 0.35 μm CMOS technology and include spiking and bursting neuron models, and synapses with short-term (facilitating/depressing) and long-term (STDP and dopamine-modulated STDP) dynamics. They enable execution of complex nonlinear models in accelerated-time, as compared with biology, and with low power consumption. The neural dynamics are implemented using analogue circuit techniques, with digital asynchronous event-based input and output. The circuits provide configurable hardware blocks that can be used to simulate a variety of neural networks. The paper presents experimental results obtained from the fabricated devices, and discusses the advantages and disadvantages of the analogue circuit approach to computational neural modelling.

  13. Reconstruction and separation of vibratory field using structural holography

    Science.gov (United States)

    Chesnais, C.; Totaro, N.; Thomas, J.-H.; Guyader, J.-L.

    2017-02-01

    A method for reconstructing and separating vibratory field on a plate-like structure is presented. The method, called "Structural Holography" is derived from classical Near-field Acoustic Holography (NAH) but in the vibratory domain. In this case, the plate displacement is measured on one-dimensional lines (the holograms) and used to reconstruct the entire two-dimensional displacement field. As a consequence, remote measurements on non directly accessible zones are possible with Structural Holography. Moreover, as it is based on the decomposition of the field into forth and back waves, Structural Holography permits to separate forces in the case of multi-sources excitation. The theoretical background of the Structural Holography method is described first. Then, to illustrate the process and the possibilities of Structural Holography, the academic test case of an infinite plate excited by few point forces is presented. With the principle of vibratory field separation, the displacement fields produced by each point force separately is reconstructed. However, the displacement field is not always meaningful and some additional treatments are mandatory to localize the position of point forces for example. From the simple example of an infinite plate, a post-processing based on the reconstruction of the structural intensity field is thus proposed. Finally, Structural Holography is generalized to finite plates and applied to real experimental measurements

  14. License plate detection algorithm

    Science.gov (United States)

    Broitman, Michael; Klopovsky, Yuri; Silinskis, Normunds

    2013-12-01

    A novel algorithm for vehicle license plates localization is proposed. The algorithm is based on pixel intensity transition gradient analysis. Near to 2500 natural-scene gray-level vehicle images of different backgrounds and ambient illumination was tested. The best set of algorithm's parameters produces detection rate up to 0.94. Taking into account abnormal camera location during our tests and therefore geometrical distortion and troubles from trees this result could be considered as passable. Correlation between source data, such as license Plate dimensions and texture, cameras location and others, and parameters of algorithm were also defined.

  15. Modeling cortical circuits.

    Energy Technology Data Exchange (ETDEWEB)

    Rohrer, Brandon Robinson; Rothganger, Fredrick H.; Verzi, Stephen J.; Xavier, Patrick Gordon

    2010-09-01

    The neocortex is perhaps the highest region of the human brain, where audio and visual perception takes place along with many important cognitive functions. An important research goal is to describe the mechanisms implemented by the neocortex. There is an apparent regularity in the structure of the neocortex [Brodmann 1909, Mountcastle 1957] which may help simplify this task. The work reported here addresses the problem of how to describe the putative repeated units ('cortical circuits') in a manner that is easily understood and manipulated, with the long-term goal of developing a mathematical and algorithmic description of their function. The approach is to reduce each algorithm to an enhanced perceptron-like structure and describe its computation using difference equations. We organize this algorithmic processing into larger structures based on physiological observations, and implement key modeling concepts in software which runs on parallel computing hardware.

  16. Memristor Circuits and Systems

    KAUST Repository

    Zidan, Mohammed A.

    2015-05-01

    Current CMOS-based technologies are facing design challenges related to the continuous scaling down of the minimum feature size, according to Moore’s law. Moreover, conventional computing architecture is no longer an effective way of fulfilling modern applications demands, such as big data analysis, pattern recognition, and vector processing. Therefore, there is an exigent need to shift to new technologies, at both the architecture and the device levels. Recently, memristor devices and structures attracted attention for being promising candidates for this job. Memristor device adds a new dimension for designing novel circuits and systems. In addition, high-density memristor-based crossbar is widely considered to be the essential element for future memory and bio-inspired computing systems. However, numerous challenges need to be addressed before the memristor genuinely replaces current memory and computing technologies, which is the motivation behind this research effort. In order to address the technology challenges, we begin by fabricating and modeling the memristor device. The devices fabricated at our local clean room enriched our understanding of the memristive phenomenon and enabled the experimental testing for our memristor-based circuits. Moreover, our proposed mathematical modeling for memristor behavior is an essential element for the theoretical circuit design stage. Designing and addressing the challenges of memristor systems with practical complexity, however, requires an extra step, which takes the form of a reliable and modular simulation platform. We, therefore, built a new simulation platform for the resistive crossbar, which can simulate realistic size arrays filled with real memory data. In addition, this simulation platform includes various crossbar nonidealities in order to obtain accurate simulation results. Consequently, we were able to address the significant challenges facing the high density memristor crossbar, as the building block for

  17. A dishwasher for circuits

    CERN Multimedia

    Rosaria Marraffino

    2014-01-01

    You have always been told that electronic devices fear water. However, at the Surface Mount Devices (SMD) Workshop here at CERN all the electronic assemblies are cleaned with a machine that looks like a… dishwasher.   The circuit dishwasher. Credit: Clara Nellist.  If you think the image above shows a dishwasher, you wouldn’t be completely wrong. Apart from the fact that the whole pumping system and the case itself are made entirely from stainless steel and chemical resistant materials, and the fact that it washes electrical boards instead of dishes… it works exactly like a dishwasher. It’s a professional machine (mainly used in the pharmaceutical industry) designed to clean everything that can be washed with a water-based chemical soap. This type of treatment increases the lifetime of the electronic boards and therefore the LHC's reliability by preventing corrosion problems in the severe radiation and ozone environment of the LHC tunn...

  18. Basic electronic circuits

    CERN Document Server

    Buckley, P M

    1980-01-01

    In the past, the teaching of electricity and electronics has more often than not been carried out from a theoretical and often highly academic standpoint. Fundamentals and basic concepts have often been presented with no indication of their practical appli­ cations, and all too frequently they have been illustrated by artificially contrived laboratory experiments bearing little relationship to the outside world. The course comes in the form of fourteen fairly open-ended constructional experiments or projects. Each experiment has associated with it a construction exercise and an explanation. The basic idea behind this dual presentation is that the student can embark on each circuit following only the briefest possible instructions and that an open-ended approach is thereby not prejudiced by an initial lengthy encounter with the theory behind the project; this being a sure way to dampen enthusiasm at the outset. As the investigation progresses, questions inevitably arise. Descriptions of the phenomena encounte...

  19. Diamond Integrated Optomechanical Circuits

    CERN Document Server

    Rath, Patrik; Nebel, Christoph; Wild, Christoph; Pernice, Wolfram H P

    2013-01-01

    Diamond offers unique material advantages for the realization of micro- and nanomechanical resonators due to its high Young's modulus, compatibility with harsh environments and superior thermal properties. At the same time, the wide electronic bandgap of 5.45eV makes diamond a suitable material for integrated optics because of broadband transparency and the absence of free-carrier absorption commonly encountered in silicon photonics. Here we take advantage of both to engineer full-scale optomechanical circuits in diamond thin films. We show that polycrystalline diamond films fabricated by chemical vapour deposition provide a convenient waferscale substrate for the realization of high quality nanophotonic devices. Using free-standing nanomechanical resonators embedded in on-chip Mach-Zehnder interferometers, we demonstrate efficient optomechanical transduction via gradient optical forces. Fabricated diamond resonators reproducibly show high mechanical quality factors up to 11,200. Our low cost, wideband, carri...

  20. Casimir force between metal plate and dielectric plate

    Institute of Scientific and Technical Information of China (English)

    刘中柱; 邵成刚; 罗俊

    1999-01-01

    The Casimir effect between metal plate and dielectric plate is discussed with 1+1-dimensional potential model without using cut-off method. Calculation shows that the Casimir force between metal plate and dielectric plate is determined not only by the potential V0, the dielectric thickness and the distance α between the metal plate and dielectric plate, but also by the dimension of the vessel. When α is far less than the dimension of the vessel, the Casimir force Fc∝α(-1); conversely Fc∝α-2. This result is significant for Casimir force experiment.

  1. Global Dynamic Numerical Simulations of Plate Tectonic Reorganizations

    Science.gov (United States)

    Morra, G.; Quevedo, L.; Butterworth, N.; Matthews, K. J.; Müller, D.

    2010-12-01

    We use a new numerical approach for global geodynamics to investigate the origin of present global plate motion and to identify the causes of the last two global tectonic reorganizations occurred about 50 and 100 million years ago (Ma) [1]. While the 50 Ma event is the most well-known global plate-mantle event, expressed by the bend in the Hawaiian-Emperor volcanic chain, a prominent plate reorganization at about 100 Ma, although presently little studied, is clearly indicated by a major bend in the fracture zones in the Indian Ocean and by a change in Pacific plate motion [2]. Our workflow involves turning plate reconstructions into surface meshes that are subsequently employed as initial conditions for global Boundary Element numerical models. The tectonic setting that anticipates the reorganizations is processed with the software GPlates, combining the 3D mesh of the paleo-plate morphology and the reconstruction of paleo-subducted slabs, elaborated from tectonic history [3]. All our models involve the entire planetary system, are fully dynamic, have free surface, are characterized by a spectacular computational speed due to the simultaneous use of the multi-pole algorithm and the Boundary Element formulation and are limited only by the use of sharp material property variations [4]. We employ this new tool to unravel the causes of plate tectonic reorganizations, producing and comparing global plate motion with the reconstructed ones. References: [1] Torsvik, T., Müller, R.D., Van der Voo, R., Steinberger, B., and Gaina, C., 2008, Global Plate Motion Frames: Toward a unified model: Reviews in Geophysics, VOL. 46, RG3004, 44 PP., 2008 [2] Wessel, P. and Kroenke, L.W. Pacific absolute plate motion since 145 Ma: An assessment of the fixed hot spot hypothesis. Journal of Geophysical Research, Vol 113, B06101, 2008 [3] L. Quevedo, G. Morra, R. D. Mueller. Parallel Fast Multipole Boundary Element Method for Crustal Dynamics, Proceeding 9th World Congress and 4th Asian

  2. Comminution circuits for compact itabirites

    Directory of Open Access Journals (Sweden)

    Pedro Ferreira Pinto

    Full Text Available Abstract In the beneficiation of compact Itabirites, crushing and grinding account for major operational and capital costs. As such, the study and development of comminution circuits have a fundamental importance for feasibility and optimization of compact Itabirite beneficiation. This work makes a comparison between comminution circuits for compact Itabirites from the Iron Quadrangle. The circuits developed are: a crushing and ball mill circuit (CB, a SAG mill and ball mill circuit (SAB and a single stage SAG mill circuit (SSSAG. For the SAB circuit, the use of pebble crushing is analyzed (SABC. An industrial circuit for 25 million tons of run of mine was developed for each route from tests on a pilot scale (grinding and industrial scale. The energy consumption obtained for grinding in the pilot tests was compared with that reported by Donda and Bond. The SSSAG route had the lowest energy consumption, 11.8kWh/t and the SAB route had the highest energy consumption, 15.8kWh/t. The CB and SABC routes had a similar energy consumption of 14.4 kWh/t and 14.5 kWh/t respectively.

  3. Sequential Polarity-Reversing Circuit

    Science.gov (United States)

    Labaw, Clayton C.

    1994-01-01

    Proposed circuit reverses polarity of electric power supplied to bidirectional dc motor, reversible electro-mechanical actuator, or other device operating in direction depending on polarity. Circuit reverses polarity each time power turned on, without need for additional polarity-reversing or direction signals and circuitry to process them.

  4. Logic Circuit Design Selected Methods

    CERN Document Server

    Vingron, Shimon P

    2012-01-01

        In three main divisions the  book covers combinational circuits, latches, and asynchronous sequential circuits. Combinational circuits have  no memorising ability, while sequential circuits have such an ability to various degrees. Latches are the simplest sequential circuits, ones with the shortest memory. The presentation is decidedly non-standard.         The design of combinational circuits is discussed in an orthodox manner using normal forms and in an unorthodox manner using set-theoretical evaluation formulas relying heavily on Karnaugh maps. The latter approach allows for a new design technique called composition.          Latches are covered very extensively. Their memory functions are expressed mathematically in a time-independent manner allowing the use of (normal, non-temporal) Boolean logic in their calculation. The theory of latches is then used as the basis for calculating asynchronous circuits.         Asynchronous circuits are specified in a tree-representation, eac...

  5. Enhancement of Linear Circuit Program

    DEFF Research Database (Denmark)

    Gaunholt, Hans; Dabu, Mihaela; Beldiman, Octavian

    1996-01-01

    In this report a preliminary user friendly interface has been added to the LCP2 program making it possible to describe an electronic circuit by actually drawing the circuit on the screen. Component values and other options and parameters can easily be set by the aid of the interface. The interface...

  6. Short-circuit impedance measurement

    DEFF Research Database (Denmark)

    Pedersen, Knud Ole Helgesen; Nielsen, Arne Hejde; Poulsen, Niels Kjølstad

    2003-01-01

    Methods for estimating the short-circuit impedance in the power grid are investigated for various voltage levels and situations. The short-circuit impedance is measured, preferably from naturally occurring load changes in the grid, and it is shown that such a measurement system faces different...

  7. Dive In to Aquatic Circuits.

    Science.gov (United States)

    Goldfarb, Joseph M.

    1995-01-01

    The article presents a method for swimming teachers and coaches to stave off workout boredom in their students by using a circuit in the pool. After explaining how to set up a training circuit, the article describes sample stations and notes important safety precautions. (SM)

  8. Enhancement of Linear Circuit Program

    DEFF Research Database (Denmark)

    Gaunholt, Hans; Dabu, Mihaela; Beldiman, Octavian

    1996-01-01

    In this report a preliminary user friendly interface has been added to the LCP2 program making it possible to describe an electronic circuit by actually drawing the circuit on the screen. Component values and other options and parameters can easily be set by the aid of the interface. The interfac...

  9. Accurate Switched-Voltage voltage averaging circuit

    OpenAIRE

    金光, 一幸; 松本, 寛樹

    2006-01-01

    Abstract ###This paper proposes an accurate Switched-Voltage (SV) voltage averaging circuit. It is presented ###to compensated for NMOS missmatch error at MOS differential type voltage averaging circuit. ###The proposed circuit consists of a voltage averaging and a SV sample/hold (S/H) circuit. It can ###operate using nonoverlapping three phase clocks. Performance of this circuit is verified by PSpice ###simulations.

  10. 46 CFR 169.670 - Circuit breakers.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Circuit breakers. 169.670 Section 169.670 Shipping COAST... Gross Tons § 169.670 Circuit breakers. Each circuit breaker must be of the manually reset type designed... the circuit without damage to the circuit breaker....

  11. Nuclear reactor alignment plate configuration

    Energy Technology Data Exchange (ETDEWEB)

    Altman, David A; Forsyth, David R; Smith, Richard E; Singleton, Norman R

    2014-01-28

    An alignment plate that is attached to a core barrel of a pressurized water reactor and fits within slots within a top plate of a lower core shroud and upper core plate to maintain lateral alignment of the reactor internals. The alignment plate is connected to the core barrel through two vertically-spaced dowel pins that extend from the outside surface of the core barrel through a reinforcement pad and into corresponding holes in the alignment plate. Additionally, threaded fasteners are inserted around the perimeter of the reinforcement pad and into the alignment plate to further secure the alignment plate to the core barrel. A fillet weld also is deposited around the perimeter of the reinforcement pad. To accomodate thermal growth between the alignment plate and the core barrel, a gap is left above, below and at both sides of one of the dowel pins in the alignment plate holes through with the dowel pins pass.

  12. Reformulating and Reconstructing Quantum Theory

    CERN Document Server

    Hardy, Lucien

    2011-01-01

    We provide a reformulation of finite dimensional quantum theory in the circuit framework in terms of mathematical axioms, and a reconstruction of quantum theory from operational postulates. The mathematical axioms for quantum theory are the following: [Axiom 1] Operations correspond to operators. [Axiom 2] Every complete set of positive operators corresponds to a complete set of operations. The following operational postulates are shown to be equivalent to these mathematical axioms: [P1] Definiteness. Associated with any given pure state is a unique maximal effect giving probability equal to one. This maximal effect does not give probability equal to one for any other pure state. [P2] Information locality. A maximal measurement on a composite system is effected if we perform maximal measurements on each of the components. [P3] Tomographic locality. The state of a composite system can be determined from the statistics collected by making measurements on the components. [P4] Compound permutatability. There exis...

  13. Neural Network for Sparse Reconstruction

    Directory of Open Access Journals (Sweden)

    Qingfa Li

    2014-01-01

    Full Text Available We construct a neural network based on smoothing approximation techniques and projected gradient method to solve a kind of sparse reconstruction problems. Neural network can be implemented by circuits and can be seen as an important method for solving optimization problems, especially large scale problems. Smoothing approximation is an efficient technique for solving nonsmooth optimization problems. We combine these two techniques to overcome the difficulties of the choices of the step size in discrete algorithms and the item in the set-valued map of differential inclusion. In theory, the proposed network can converge to the optimal solution set of the given problem. Furthermore, some numerical experiments show the effectiveness of the proposed network in this paper.

  14. Re-examination of geophysical data off Northwest India: Implications to the Late Cretaceous plate tectonics between India and Africa.

    Digital Repository Service at National Institute of Oceanography (India)

    Ramana, M.V.; Desa, M.; Ramprasad, T.

    processes. Late Cretaceous seafloor spreading between India and Africa formed the Mascarene Basin, and the plate reconstruction models depict unequal crustal accretion in this basin. Re-interpretation of magnetic data in the Gop and Laxmi Basins suggests...

  15. A true polar wander model for Neoproterozoic plate motions

    Energy Technology Data Exchange (ETDEWEB)

    Ripperdan, R.L. (Weizmann Inst. of Science, Rehovot (Israel))

    1992-01-01

    Recent paleogeographic reconstructions for the interval 750--500 Ma (Neoproterozoic to Late Cambrian) require rapid rates of plate motion and/or rotation around an equatorial Euler pole to accommodate reconstructions for the Early Paleozoic. Motions of this magnitude appear to be very uncommon during the Phanerozoic. A model for plate motions based on the hypothesis that discrete intervals of rapid true polar wander (RTPW) occurred during the Neoproterozoic can account for the paleogeographic changes with minimum amounts of plate motion. The model uses the paleogeographic reconstructions of Hoffman (1991). The following constraints were applied during derivation of the model: (1) relative motions between major continental units were restricted to be combinations of great circle or small circle translations with Euler poles of rotation = spin axis; (2) maximum rates of relative translational plate motion were 0.2 m/yr. Based on these constraints, two separate sets of synthetic plate motion trajectories were determined. The sequence of events in both can be summarized as: (1) A rapid true polar wander event of ca 90[degree] rafting a supercontinent to the spin axis; (2) breakup of the polar supercontinent into two fragments, one with the Congo, West Africa, Amazonia, and Baltica cratons, the other with the Laurentia, East Gondwana, and Kalahari cratons; (3) great circle motion of the blocks towards the equator; (4) small circle motion leading to amalgamation of Gondwana and separation of Laurentia and Baltica. In alternative 1, rifting initiates between East Antarctica and Laurentia and one episode of RTPW is required. Alternative 2 requires two episodes of RTPW; and that rifting occurred first along the eastern margin and later along the western margin of Laurentia. Synthetic plate motion trajectories are compared to existing paleomagnetic and geological data, and implications of the model for paleoclimatic changes during the Neoproterozoic are discussed.

  16. Create Your Plate

    Medline Plus

    Full Text Available ... 1 Type 2 About Us Online Community Meal Planning Sign In Search: Search More Sites Search ≡ Are ... Fitness Home Food MyFoodAdvisor Recipes Association Cookbook Recipes Planning Meals Diabetes Meal Plans Create Your Plate Gluten ...

  17. Create Your Plate

    Medline Plus

    Full Text Available ... Create Your Plate is a simple and effective way to manage your blood glucose levels and lose weight. With ... year of delicious meals to help prevent and manage diabetes. Healthy Recipes: ... to your day with this guide. Ways to Give: Wear Your Cause on Your Sleeve - ...

  18. The Plate Tectonics Project

    Science.gov (United States)

    Hein, Annamae J.

    2011-01-01

    The Plate Tectonics Project is a multiday, inquiry-based unit that facilitates students as self-motivated learners. Reliable Web sites are offered to assist with lessons, and a summative rubric is used to facilitate the holistic nature of the project. After each topic (parts of the Earth, continental drift, etc.) is covered, the students will…

  19. Create Your Plate

    Medline Plus

    Full Text Available ... tax-deductible gift today can fund critical diabetes research and support vital diabetes education services that improve the ... way to manage your blood glucose levels and lose weight. With this method, you fill your plate with more non-starchy ...

  20. Create Your Plate

    Medline Plus

    Full Text Available ... 1 Type 2 About Us Online Community Meal Planning Sign In Search: Search More Sites Search ≡ Are ... Fitness Home Food MyFoodAdvisor Recipes Association Cookbook Recipes Planning Meals Diabetes Meal Plans Create Your Plate Gluten ...

  1. Create Your Plate

    Medline Plus

    Full Text Available ... tax-deductible gift today can fund critical diabetes research and support vital diabetes education services that improve the ... way to manage your blood glucose levels and lose weight. With this method, you fill your plate with more non-starchy ...

  2. Create Your Plate

    Medline Plus

    Full Text Available ... unsweetened tea or coffee. Featured Product Precise Portions® Go Healthy Travel Pack (4/Box) Taking the guesswork ... you are. Now, our best-selling, sectioned to-go plate with easy-sealing lid is offered in ...

  3. Create Your Plate

    Medline Plus

    Full Text Available ... manage portion control wherever you are. Now, our best-selling, sectioned to-go plate with easy-sealing lid is offered in a 4-pack. Whether ... Research & Practice We Are Research Leaders We Support Your Doctor ...

  4. INL HIP Plate Fabrication

    Energy Technology Data Exchange (ETDEWEB)

    B. H. Park; C. R. Clark; J. F. Jue

    2010-02-01

    This document outlines the process used to bond monolithic fuel plates by Hot Isostatic Pressing (HIP). This method was developed at Idaho National Laboratory (INL) for the Reduced Enrichment for Research and Test Reactors (RERTR) program. These foils have been used in a number of irradiation experiments in support of the United States Global Threat Reduction Initiative (GTRI) program.

  5. The Plate Tectonics Project

    Science.gov (United States)

    Hein, Annamae J.

    2011-01-01

    The Plate Tectonics Project is a multiday, inquiry-based unit that facilitates students as self-motivated learners. Reliable Web sites are offered to assist with lessons, and a summative rubric is used to facilitate the holistic nature of the project. After each topic (parts of the Earth, continental drift, etc.) is covered, the students will…

  6. Create Your Plate

    Medline Plus

    Full Text Available ... Planning Meals > Create Your Plate Share: Print Page Text Size: A A A Listen En Español Create ... somewhere in between, you have an easy portion control solution that works. Last Reviewed: October 8, 2015 Last Edited: ... Cost of Diabetes Advocate Toolkit Call to Congress Research & ...

  7. Neuromagnetic source reconstruction

    Energy Technology Data Exchange (ETDEWEB)

    Lewis, P.S.; Mosher, J.C. [Los Alamos National Lab., NM (United States); Leahy, R.M. [University of Southern California, Los Angeles, CA (United States)

    1994-12-31

    In neuromagnetic source reconstruction, a functional map of neural activity is constructed from noninvasive magnetoencephalographic (MEG) measurements. The overall reconstruction problem is under-determined, so some form of source modeling must be applied. We review the two main classes of reconstruction techniques-parametric current dipole models and nonparametric distributed source reconstructions. Current dipole reconstructions use a physically plausible source model, but are limited to cases in which the neural currents are expected to be highly sparse and localized. Distributed source reconstructions can be applied to a wider variety of cases, but must incorporate an implicit source, model in order to arrive at a single reconstruction. We examine distributed source reconstruction in a Bayesian framework to highlight the implicit nonphysical Gaussian assumptions of minimum norm based reconstruction algorithms. We conclude with a brief discussion of alternative non-Gaussian approachs.

  8. Neuromagnetic source reconstruction

    Energy Technology Data Exchange (ETDEWEB)

    Lewis, P.S.; Mosher, J.C. [Los Alamos National Lab., NM (United States); Leahy, R.M. [University of Southern California, Los Angeles, CA (United States)

    1994-12-31

    In neuromagnetic source reconstruction, a functional map of neural activity is constructed from noninvasive magnetoencephalographic (MEG) measurements. The overall reconstruction problem is under-determined, so some form of source modeling must be applied. We review the two main classes of reconstruction techniques-parametric current dipole models and nonparametric distributed source reconstructions. Current dipole reconstructions use a physically plausible source model, but are limited to cases in which the neural currents are expected to be highly sparse and localized. Distributed source reconstructions can be applied to a wider variety of cases, but must incorporate an implicit source, model in order to arrive at a single reconstruction. We examine distributed source reconstruction in a Bayesian framework to highlight the implicit nonphysical Gaussian assumptions of minimum norm based reconstruction algorithms. We conclude with a brief discussion of alternative non-Gaussian approachs.

  9. Photodiode circuits for retinal prostheses.

    Science.gov (United States)

    Loudin, J D; Cogan, S F; Mathieson, K; Sher, A; Palanker, D V

    2011-10-01

    Photodiode circuits show promise for the development of high-resolution retinal prostheses. While several of these systems have been constructed and some even implanted in humans, existing descriptions of the complex optoelectronic interaction between light, photodiode, and the electrode/electrolyte load are limited. This study examines this interaction in depth with theoretical calculations and experimental measurements. Actively biased photoconductive and passive photovoltaic circuits are investigated, with the photovoltaic circuits consisting of one or more diodes connected in series, and the photoconductive circuits consisting of a single diode in series with a pulsed bias voltage. Circuit behavior and charge injection levels were markedly different for platinum and sputtered iridium-oxide film (SIROF) electrodes. Photovoltaic circuits were able to deliver 0.038 mC/cm(2) (0.75 nC/phase) per photodiode with 50- μm platinum electrodes, and 0.54-mC/cm(2) (11 nC/phase) per photodiode with 50-μ m SIROF electrodes driven with 0.5-ms pulses of light at 25 Hz. The same pulses applied to photoconductive circuits with the same electrodes were able to deliver charge injections as high as 0.38 and 7.6 mC/cm(2) (7.5 and 150 nC/phase), respectively. We demonstrate photovoltaic stimulation of rabbit retina in-vitro, with 0.5-ms pulses of 905-nm light using peak irradiance of 1 mW/mm(2). Based on the experimental data, we derive electrochemical and optical safety limits for pixel density and charge injection in various circuits. While photoconductive circuits offer smaller pixels, photovoltaic systems do not require an external bias voltage. Both classes of circuits show promise for the development of high-resolution optoelectronic retinal prostheses.

  10. 经腹直肌外侧切口入路重建钢板辅助后柱顺行拉力螺钉治疗复杂髋臼骨折%Surgical treatment of complex acetabular fractures through the lateral-rectus approach with the pelvic reconstructive plate and antegrade posterior-column lag screw

    Institute of Scientific and Technical Information of China (English)

    张潇; 杨晓东; 夏广; 李涛; 王华; 熊然; 樊仕才

    2015-01-01

    Objective To evaluate the clinical value of the lateral-rectus approach with the pelvic recon-structive plate and antegrade posterior -column lag screw in the treatment of complex acetabular fractures .Meth-ods Between May 2012 and Jan.2014,9 patients with complex acetabular fractures were treated with pelvic recon-structive plate and antegrade posterior-column lag screw through the lateral-rectus approach . There were 6 males and 3 females,aged 27-74 years(mean,39 years).Fractures were caused by traffic accident in 5 cases,by falling in 2 cases,and by heavy crash in 2 cases.According to Letournel classification ,there were 2 cases of transverse frac-ture,4 cases of anterior column with posterior hemi-transverse lesion fracture,and 3 cases of both-column fracture with 1 case of central dislocation of hip joint .The operation time and blood loss were statistically analyzed .The pa-tients were evaluated clinically according to Merle d'Aubigne-Postel scoring system and X ray performance based on the criteria described by Matta .Results The average time of operation was 200 minutes ( 150-255 minutes );the average blood loss was 730ml(300-1250ml);the average follow up was 15.9 months(9-30 months);the clinical results were excellent in 5 patients,good in 2 and fair in 2.The radiological results were anatomical reduction in 5 patients,satisfactory in 3 and fair in 1.All the patients were healed within 3 months and there were no complications such as infection ,avascular necrosis of the femoral head ( ANFH) ,or heterotopic ossification .Conclusion The lat-eral-rectus approach is suitable for some complex acetabular fractures ,with advantages of the adequate exposure of quadrilateral surface and insertion of the posterior column antegrade lag screw .%目的:评价经腹直肌外侧切口入路以前柱重建钢板配合后柱顺行拉力螺钉内固定治疗复杂髋臼骨折的临床疗效。方法回顾性分析自2012年5月~2014年1月本科

  11. An inktjet printing-based process chain for conductive structures on printed circuit board materials

    NARCIS (Netherlands)

    Sridhar, Ashok

    2010-01-01

    A process chain to fabricate conductive structures on printed circuit board material is presented in this thesis. This process chain comprises four main steps: plasma treatment, inkjet printing, electroless plating and functional characterisation. It represents a drastic reduction in the number of

  12. Experimental Device for Learning of Logical Circuit Design using Integrated Circuits

    OpenAIRE

    石橋, 孝昭

    2012-01-01

    This paper presents an experimental device for learning of logical circuit design using integrated circuits and breadboards. The experimental device can be made at a low cost and can be used for many subjects such as logical circuits, computer engineering, basic electricity, electrical circuits and electronic circuits. The proposed device is effective to learn the logical circuits than the usual lecture.

  13. 30 CFR 75.800 - High-voltage circuits; circuit breakers.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false High-voltage circuits; circuit breakers. 75.800... § 75.800 High-voltage circuits; circuit breakers. High-voltage circuits entering the underground area of any coal mine shall be protected by suitable circuit breakers of adequate interrupting...

  14. Performance analysis of electrical circuits /PANE/

    Science.gov (United States)

    Johnson, K. L.; Steinberg, L. L.

    1968-01-01

    Automated statistical and worst case computer program has been designed to perform dc and ac steady circuit analyses. The program determines the worst case circuit performance by solving circuit equations.

  15. Laser-induced selective copper plating of polypropylene surface

    Science.gov (United States)

    Ratautas, K.; Gedvilas, M.; Stankevičiene, I.; JagminienÄ--, A.; Norkus, E.; Li Pira, N.; Sinopoli, S.; Emanuele, U.; Račiukaitis, G.

    2016-03-01

    Laser writing for selective plating of electro-conductive lines for electronics has several significant advantages, compared to conventional printed circuit board technology. Firstly, this method is faster and cheaper at the prototyping stage. Secondly, material consumption is reduced, because it works selectively. However, the biggest merit of this method is potentiality to produce moulded interconnect device, enabling to create electronics on complex 3D surfaces, thus saving space, materials and cost of production. There are two basic techniques of laser writing for selective plating on plastics: the laser-induced selective activation (LISA) and laser direct structuring (LDS). In the LISA method, pure plastics without any dopant (filler) can be used. In the LDS method, special fillers are mixed in the polymer matrix. These fillers are activated during laser writing process, and, in the next processing step, the laser modified area can be selectively plated with metals. In this work, both methods of the laser writing for the selective plating of polymers were investigated and compared. For LDS approach, new material: polypropylene with carbon-based additives was tested using picosecond and nanosecond laser pulses. Different laser processing parameters (laser pulse energy, scanning speed, the number of scans, pulse durations, wavelength and overlapping of scanned lines) were applied in order to find out the optimal regime of activation. Areal selectivity tests showed a high plating resolution. The narrowest width of a copper-plated line was less than 23 μm. Finally, our material was applied to the prototype of the electronic circuit board on a 2D surface.

  16. Variational integrators for electric circuits

    Energy Technology Data Exchange (ETDEWEB)

    Ober-Blöbaum, Sina, E-mail: sinaob@math.upb.de [Computational Dynamics and Optimal Control, University of Paderborn (Germany); Tao, Molei [Courant Institute of Mathematical Sciences, New York University (United States); Cheng, Mulin [Applied and Computational Mathematics, California Institute of Technology (United States); Owhadi, Houman; Marsden, Jerrold E. [Control and Dynamical Systems, California Institute of Technology (United States); Applied and Computational Mathematics, California Institute of Technology (United States)

    2013-06-01

    In this contribution, we develop a variational integrator for the simulation of (stochastic and multiscale) electric circuits. When considering the dynamics of an electric circuit, one is faced with three special situations: 1. The system involves external (control) forcing through external (controlled) voltage sources and resistors. 2. The system is constrained via the Kirchhoff current (KCL) and voltage laws (KVL). 3. The Lagrangian is degenerate. Based on a geometric setting, an appropriate variational formulation is presented to model the circuit from which the equations of motion are derived. A time-discrete variational formulation provides an iteration scheme for the simulation of the electric circuit. Dependent on the discretization, the intrinsic degeneracy of the system can be canceled for the discrete variational scheme. In this way, a variational integrator is constructed that gains several advantages compared to standard integration tools for circuits; in particular, a comparison to BDF methods (which are usually the method of choice for the simulation of electric circuits) shows that even for simple LCR circuits, a better energy behavior and frequency spectrum preservation can be observed using the developed variational integrator.

  17. Effects of adhesive, host plate, transducer and excitation parameters on time reversibility of ultrasonic Lamb waves.

    Science.gov (United States)

    Agrahari, J K; Kapuria, S

    2016-08-01

    To develop an effective baseline-free damage detection strategy using the time-reversal process (TRP) of Lamb waves in thin walled structures, it is essential to develop a good understanding of the parameters that affect the amplitude dispersion and consequently the time reversibility of the Lamb wave signal. In this paper, the effects of adhesive layer between the transducers and the host plate, the tone burst count of the excitation signal, the plate thickness, and the piezoelectric transducer thickness on the time reversibility of Lamb waves in metallic plates are studied using experiments and finite element simulations. The effect of adhesive layer on the forward propagation response and frequency tuning has been also studied. The results show that contrary to the general expectation, the quality of the reconstruction of the input signal after the TRP may increase with the increase in the adhesive layer thickness at certain frequency ranges. Similarly, an increase in the tone burst count resulting in a narrowband signal does not necessarily enhance the time reversibility at all frequencies, contrary to what has been reported earlier. For a given plate thickness, a thinner transducer yields a better reconstruction, but for a given transducer thickness, the similarity of the reconstructed signal may not be always higher for a thicker plate. It is important to study these effects to achieve the best quality of reconstruction in undamaged plates, for effective damage detection.

  18. MyPlate Food Guide

    Science.gov (United States)

    ... Choosing the Right Sport for You Shyness MyPlate Food Guide KidsHealth > For Teens > MyPlate Food Guide Print ... other sugary drinks. Avoid oversized portions. continue Five Food Groups Different food groups meet different nutrition needs. ...

  19. What Are Growth Plate Injuries?

    Science.gov (United States)

    ... plate injuries are:  Falling down  Competitive sports (like football)  Recreational activities. Other reasons for growth plate injuries are:  Child abuse  Injury from extreme cold (for ...

  20. Overpulse railgun energy recovery circuit

    Energy Technology Data Exchange (ETDEWEB)

    Honig, E.M.

    1984-09-28

    The invention presented relates to a high-power pulsing circuit and more particularly to a repetitive pulse inductive energy storage and transfer circuit for an electromagnetic launcher. In an electromagnetic launcher such as a railgun for propelling a projectile at high velocity, an overpulse energy recovery circuit is employed to transfer stored inductive energy from a source inductor to the railgun inductance to propel the projectile down the railgun. Switching circuitry and an energy transfer capacitor are used to switch the energy back to the source inductor in readiness for a repetitive projectile propelling cycle.

  1. Counterpulse railgun energy recovery circuit

    Energy Technology Data Exchange (ETDEWEB)

    Honig, E.M.

    1984-09-28

    The invention presented relates to a high-power pulsing circuit and more particularly to a repetitive pulse inductive energy storage and transfer circuit for an electromagnetic launcher. In an electromagnetic launcher such as a railgun for propelling a projectile at high velocity, a counterpulse energy recovery circuit is employed to transfer stored inductive energy from a source inductor to the railgun inductance to propel the projectile down the railgun. Switching circuitry and an energy transfer capacitor are used to switch the energy back to the source inductor in readiness for a repetitive projectile propelling cycle.

  2. The Maplin electronic circuits handbook

    CERN Document Server

    Tooley, Michael

    2015-01-01

    The Maplin Electronic Circuits Handbook provides pertinent data, formula, explanation, practical guidance, theory and practical guidance in the design, testing, and construction of electronic circuits. This book discusses the developments in electronics technology techniques.Organized into 11 chapters, this book begins with an overview of the common types of passive component. This text then provides the reader with sufficient information to make a correct selection of passive components for use in the circuits. Other chapters consider the various types of the most commonly used semiconductor

  3. Secure integrated circuits and systems

    CERN Document Server

    Verbauwhede, Ingrid MR

    2010-01-01

    On any advanced integrated circuit or 'system-on-chip' there is a need for security. In many applications the actual implementation has become the weakest link in security rather than the algorithms or protocols. The purpose of the book is to give the integrated circuits and systems designer an insight into the basics of security and cryptography from the implementation point of view. As a designer of integrated circuits and systems it is important to know both the state-of-the-art attacks as well as the countermeasures. Optimizing for security is different from optimizations for speed, area,

  4. Determining Covers in Combinational Circuits

    Directory of Open Access Journals (Sweden)

    Ljubomir Cvetkovic

    2011-05-01

    Full Text Available In this paper we propose a procedure for determining 0- or 1-cover of an arbitrary line in a combinational circuit. When determining a cover we do not need Boolean expression for the line; only the circuit structure is used. Within the proposed procedure we use the tools of the cube theory, in particular, some operations defined on cubes. The procedure can be applied for determining 0- and 1- covers of output lines in programmable logic devices. Basically, this procedure is a method for the analysis of a combinational circuit.

  5. Controlling Laminate Plate Elastic Behavior

    OpenAIRE

    Mareš, T.

    2004-01-01

    This paper aims to express the relation of a measure of laminate plate stiffness with respect to the fiber orientation of its plies. The inverse of the scalar product of the lateral displacement of the central plane and lateral loading of the plate is the measure of laminate plate stiffness. In the case of a simply supported rectangular laminate plate this measure of stiffness is maximized, and the optimum orientation of its plies is searched.

  6. Breast reconstruction after mastectomy

    Directory of Open Access Journals (Sweden)

    Daniel eSchmauss

    2016-01-01

    Full Text Available Breast cancer is the leading cause of cancer death in women worldwide. Its surgical approach has become less and less mutilating in the last decades. However, the overall number of breast reconstructions has significantly increased lately. Nowadays breast reconstruction should be individualized at its best, first of all taking into consideration oncological aspects of the tumor, neo-/adjuvant treatment and genetic predisposition, but also its timing (immediate versus delayed breast reconstruction, as well as the patient’s condition and wish. This article gives an overview over the various possibilities of breast reconstruction, including implant- and expander-based reconstruction, flap-based reconstruction (vascularized autologous tissue, the combination of implant and flap, reconstruction using non-vascularized autologous fat, as well as refinement surgery after breast reconstruction.

  7. Microchannel plate streak camera

    Science.gov (United States)

    Wang, Ching L.

    1989-01-01

    An improved streak camera in which a microchannel plate electron multiplier is used in place of or in combination with the photocathode used in prior streak cameras. The improved streak camera is far more sensitive to photons (UV to gamma-rays) than the conventional x-ray streak camera which uses a photocathode. The improved streak camera offers gamma-ray detection with high temporal resolution. It also offers low-energy x-ray detection without attenuation inside the cathode. Using the microchannel plate in the improved camera has resulted in a time resolution of about 150 ps, and has provided a sensitivity sufficient for 1000 KeV x-rays.

  8. Electronic Equipment Cold Plates

    Science.gov (United States)

    1976-04-01

    equations for such a flow regiae. For laainar flow and Moderate teaperature differwwe« between the well «nd coolant, a aodifled Sieder -Tate...con- figuration. The heat-transfer coefficients, therefore, were determined by using both the Sieder -Tate and McAdams equations and the coaputed...values used In the analytical predictions. As with th* previous cold Plates, the Sieder -Tate equation gave too low of values for the heat- transfer

  9. Elastic plate spallation

    Science.gov (United States)

    Oline, L.; Medaglia, J.

    1972-01-01

    The dynamic finite element method was used to investigate elastic stress waves in a plate. Strain displacement and stress strain relations are discussed along with the stiffness and mass matrix. The results of studying point load, and distributed load over small, intermediate, and large radii are reported. The derivation of finite element matrices, and the derivation of lumped and consistent matrices for one dimensional problems with Laplace transfer solutions are included. The computer program JMMSPALL is also included.

  10. Tomography of integrated circuit interconnect with an electromigration void

    Energy Technology Data Exchange (ETDEWEB)

    Levine, Zachary H. [National Institute of Standards and Technology, Gaithersburg, Maryland 20899-8410 (United States); Rensselaer Polytechnic Institute, Troy, New York 12180-3590 (United States); Kalukin, Andrew R. [National Institute of Standards and Technology, Gaithersburg, Maryland 20899-8410 (United States); Kuhn, Markus [Intel Corporation RA1-329, 5200 Northeast Elam Young Parkway, Hillsboro, Oregon 74124 (United States); Frigo, Sean P. [Advanced Photon Source, Argonne National Laboratory, 9700 South Cass Avenue, Argonne, Illinois 60439 (United States); McNulty, Ian [Advanced Photon Source, Argonne National Laboratory, 9700 South Cass Avenue, Argonne, Illinois 60439 (United States); Retsch, Cornelia C. [Advanced Photon Source, Argonne National Laboratory, 9700 South Cass Avenue, Argonne, Illinois 60439 (United States); Wang, Yuxin [Advanced Photon Source, Argonne National Laboratory, 9700 South Cass Avenue, Argonne, Illinois 60439 (United States); Arp, Uwe [National Institute of Standards and Technology, Gaithersburg, Maryland 20899-8410 (United States); Lucatorto, Thomas B. [National Institute of Standards and Technology, Gaithersburg, Maryland 20899-8410 (United States); Ravel, Bruce D. [National Institute of Standards and Technology, Gaithersburg, Maryland 20899-8410 (United States)] (and others)

    2000-05-01

    An integrated circuit interconnect was subject to accelerated-life test conditions to induce an electromigration void. The silicon substrate was removed, leaving only the interconnect test structure encased in silica. We imaged the sample with 1750 eV photons using the 2-ID-B scanning transmission x-ray microscope at the Advanced Photon Source, a third-generation synchrotron facility. Fourteen views through the sample were obtained over a 170 degree sign range of angles (with a 40 degree sign gap) about a single rotation axis. Two sampled regions were selected for three-dimensional reconstruction: one of the ragged end of a wire depleted by the void, the other of the adjacent interlevel connection (or ''via''). We applied two reconstruction techniques: the simultaneous iterative reconstruction technique and a Bayesian reconstruction technique, the generalized Gaussian Markov random field method. The stated uncertainties are total, with one standard deviation, which resolved the sample to 200{+-}70 and 140{+-}30 nm, respectively. The tungsten via is distinguished from the aluminum wire by higher absorption. Within the void, the aluminum is entirely depleted from under the tungsten via. The reconstructed data show the applicability of this technique to three-dimensional imaging of buried defects in submicrometer structures relevant to the microelectronics industry. (c) 2000 American Institute of Physics.

  11. Reoperative midface reconstruction.

    Science.gov (United States)

    Acero, Julio; García, Eloy

    2011-02-01

    Reoperative reconstruction of the midface is a challenging issue because of the complexity of this region and the severity of the aesthetic and functional sequela related to the absence or failure of a primary reconstruction. The different situations that can lead to the indication of a reoperative reconstructive procedure after previous oncologic ablative procedures in the midface are reviewed. Surgical techniques, anatomic problems, and limitations affecting the reoperative reconstruction in this region of the head and neck are discussed.

  12. Plate Tearing by a Cone

    DEFF Research Database (Denmark)

    Simonsen, Bo Cerup

    1997-01-01

    The present paper is concerned with steady-state plate tearing by a cone. This is a scenario where a cone is forced through a ductile metal plate with a constant lateral tip penetration in a motion in the plane of the plate. The considered process could be an idealisaton of the damage, which...

  13. Plate Tearing by a Cone

    DEFF Research Database (Denmark)

    Simonsen, Bo Cerup

    1998-01-01

    The present paper is concerned with steady-state plate tearing by a cone. This is a scenario where a cone is forced through a ductile metal plate with a constant lateral tip penetration in a motion in the plane of the plate. The considered process could be an idealisation of the damage, which...

  14. Finite element analysis of the stability of combined plate internal fixation in posterior wall fractures of acetabulum.

    Science.gov (United States)

    Liu, Xi-Ming; Pan, Chang-Wu; Wang, Guo-Dong; Cai, Xian-Hua; Chen, Lei; Meng, Cheng-Fei; Huang, Jin-Cheng

    2015-01-01

    This study aims to explore the mechanical stability of combined plate internal fixation in posterior wall fractures of the acetabulum. The fracture and internal fixation models were established in this study and they were divided into four kinds of internal fixation models, finite element analysis was performed. The four groups were 2 mini-plates and 1 reconstruction plate fixation (A), Reconstruction plate internal fixation group (B), 2 screws internal fixation group (C) and mini-plates internal fixation group (D). The displacement of each node was measured and evaluated. There was no distortion in the geometric shape of the finite element model. The results of stress showed that it was less in the anterior pelvic ring and distributed uniform in labrum acetabulare; the stress was bigger in the upper and middle of sacroiliac joint and sciatic notch in sitting position. Combined plate internal fixation for posterior wall fractures of acetabular were stable and reliable, it is better than the other three methods.

  15. Surfaces, Digitisations and Reconstructions

    DEFF Research Database (Denmark)

    2015-01-01

    We present a new digital reconstruction of r-regular sets in three-dimensional Euclidean space. We introduce a vector field and analyse the relation between the topologies of the boundaries of the r-regular set and its reconstruction. This reconstruction can be carried out faster than prior models...... based on the same digitisation, making it attractive for computing....

  16. Immediate reconstruction of the mandible after resection for aggressive odontogenic tumours: a cohort study

    NARCIS (Netherlands)

    Simon, E.N.; Merkx, M.A.W.; Kalyanyama, B.M.; Shubi, F.M.; Stoelinga, P.J.W.

    2013-01-01

    The results are reported of a clinical follow-up study on 32 selected but consecutive patients with mandibular ameloblastoma. They were all treated by a segmental resection and reconstructed, using two 2.3 mm reconstruction plates and an autogenous particulate bone graft, taken from the anterior

  17. Polylactide bioabsorbable struts for chest wall reconstruction in a pediatric patient.

    Science.gov (United States)

    Makarawo, Tafadzwa P; Reynolds, Richard A; Cullen, Marc L

    2015-02-01

    Chest wall reconstruction after pediatric tumor resection is challenging. Children have unique characteristics related to growth and prosthetic material for reconstruction must be chosen carefully. Poly-L-Lactide (PLA), a bioabsorbable prosthetic material, has been used in the plate form for reconstruction after tumor resection in children. Recently developed PLA struts have been successfully used to reconstruct pediatric chest wall deformities. This is the first description of the use of PLA rib struts to reconstruct chest wall defects after a pediatric chest wall tumor resection. Copyright © 2015 The Society of Thoracic Surgeons. Published by Elsevier Inc. All rights reserved.

  18. Effect of Sensors on the Reliability and Control Performance of Power Circuits in the Web of Things (WoT

    Directory of Open Access Journals (Sweden)

    Sungwoo Bae

    2016-09-01

    Full Text Available In order to realize a true WoT environment, a reliable power circuit is required to ensure interconnections among a range of WoT devices. This paper presents research on sensors and their effects on the reliability and response characteristics of power circuits in WoT devices. The presented research can be used in various power circuit applications, such as energy harvesting interfaces, photovoltaic systems, and battery management systems for the WoT devices. As power circuits rely on the feedback from voltage/current sensors, the system performance is likely to be affected by the sensor failure rates, sensor dynamic characteristics, and their interface circuits. This study investigated how the operational availability of the power circuits is affected by the sensor failure rates by performing a quantitative reliability analysis. In the analysis process, this paper also includes the effects of various reconstruction and estimation techniques used in power processing circuits (e.g., energy harvesting circuits and photovoltaic systems. This paper also reports how the transient control performance of power circuits is affected by sensor interface circuits. With the frequency domain stability analysis and circuit simulation, it was verified that the interface circuit dynamics may affect the transient response characteristics of power circuits. The verification results in this paper showed that the reliability and control performance of the power circuits can be affected by the sensor types, fault tolerant approaches against sensor failures, and the response characteristics of the sensor interfaces. The analysis results were also verified by experiments using a power circuit prototype.

  19. Effect of Sensors on the Reliability and Control Performance of Power Circuits in the Web of Things (WoT).

    Science.gov (United States)

    Bae, Sungwoo; Kim, Myungchin

    2016-09-06

    In order to realize a true WoT environment, a reliable power circuit is required to ensure interconnections among a range of WoT devices. This paper presents research on sensors and their effects on the reliability and response characteristics of power circuits in WoT devices. The presented research can be used in various power circuit applications, such as energy harvesting interfaces, photovoltaic systems, and battery management systems for the WoT devices. As power circuits rely on the feedback from voltage/current sensors, the system performance is likely to be affected by the sensor failure rates, sensor dynamic characteristics, and their interface circuits. This study investigated how the operational availability of the power circuits is affected by the sensor failure rates by performing a quantitative reliability analysis. In the analysis process, this paper also includes the effects of various reconstruction and estimation techniques used in power processing circuits (e.g., energy harvesting circuits and photovoltaic systems). This paper also reports how the transient control performance of power circuits is affected by sensor interface circuits. With the frequency domain stability analysis and circuit simulation, it was verified that the interface circuit dynamics may affect the transient response characteristics of power circuits. The verification results in this paper showed that the reliability and control performance of the power circuits can be affected by the sensor types, fault tolerant approaches against sensor failures, and the response characteristics of the sensor interfaces. The analysis results were also verified by experiments using a power circuit prototype.

  20. Effect of Sensors on the Reliability and Control Performance of Power Circuits in the Web of Things (WoT)

    Science.gov (United States)

    Bae, Sungwoo; Kim, Myungchin

    2016-01-01

    In order to realize a true WoT environment, a reliable power circuit is required to ensure interconnections among a range of WoT devices. This paper presents research on sensors and their effects on the reliability and response characteristics of power circuits in WoT devices. The presented research can be used in various power circuit applications, such as energy harvesting interfaces, photovoltaic systems, and battery management systems for the WoT devices. As power circuits rely on the feedback from voltage/current sensors, the system performance is likely to be affected by the sensor failure rates, sensor dynamic characteristics, and their interface circuits. This study investigated how the operational availability of the power circuits is affected by the sensor failure rates by performing a quantitative reliability analysis. In the analysis process, this paper also includes the effects of various reconstruction and estimation techniques used in power processing circuits (e.g., energy harvesting circuits and photovoltaic systems). This paper also reports how the transient control performance of power circuits is affected by sensor interface circuits. With the frequency domain stability analysis and circuit simulation, it was verified that the interface circuit dynamics may affect the transient response characteristics of power circuits. The verification results in this paper showed that the reliability and control performance of the power circuits can be affected by the sensor types, fault tolerant approaches against sensor failures, and the response characteristics of the sensor interfaces. The analysis results were also verified by experiments using a power circuit prototype. PMID:27608020

  1. Millimeter-wave and terahertz integrated circuit antennas

    Science.gov (United States)

    Rebeiz, Gabriel M.

    1992-01-01

    This paper presents a comprehensive review of integrated circuit antennas suitable for millimeter and terahertz applications. A great deal of research was done on integrated circuit antennas in the last decade and many of the problems associated with electrically thick dielectric substrates, such as substrate modes and poor radiation patterns, have been understood and solved. Several new antennas, such as the integrated horn antenna, the dielectric-filled parabola, the Fresnel plate antenna, the dual-slot antenna, and the log-periodic and spiral antennas on extended hemispherical lenses, have resulted in excellent performance at millimeter-wave frequencies, and are covered in detail in this paper. Also, a review of the efficiency definitions used with planar antennas is given in detail in the appendix.

  2. Intra-European Student Mobility in International Higher Education Circuits. Europe on the Move

    NARCIS (Netherlands)

    Van Mol, C.

    2014-01-01

    Intra-European Student Mobility in International Higher Education Circuits focuses on the phenomenon of international student exchanges in Europe. Strongly interdisciplinary in its focus, this book empirically addresses four main research questions: who goes abroad, how students reconstruct their so

  3. CADAT integrated circuit mask analysis

    Science.gov (United States)

    1981-01-01

    CADAT System Mask Analysis Program (MAPS2) is automated software tool for analyzing integrated-circuit mask design. Included in MAPS2 functions are artwork verification, device identification, nodal analysis, capacitance calculation, and logic equation generation.

  4. Circuit design on plastic foils

    CERN Document Server

    Raiteri, Daniele; Roermund, Arthur H M

    2015-01-01

    This book illustrates a variety of circuit designs on plastic foils and provides all the information needed to undertake successful designs in large-area electronics.  The authors demonstrate architectural, circuit, layout, and device solutions and explain the reasons and the creative process behind each. Readers will learn how to keep under control large-area technologies and achieve robust, reliable circuit designs that can face the challenges imposed by low-cost low-temperature high-throughput manufacturing.   • Discusses implications of problems associated with large-area electronics and compares them to standard silicon; • Provides the basis for understanding physics and modeling of disordered material; • Includes guidelines to quickly setup the basic CAD tools enabling efficient and reliable designs; • Illustrates practical solutions to cope with hard/soft faults, variability, mismatch, aging and bias stress at architecture, circuit, layout, and device levels.

  5. Chaos Control for Chua's Circuits

    Science.gov (United States)

    Tôrres, L. A. B.; Aguirre, L. A.; Palhares, R. M.; Mendes, E. M. A. M.

    The practical implementation of Chua's circuit control methods is discussed in this chapter. In order to better address this subject, an inductorless Chua's circuit realization is first presented, followed by practical issues related to data analysis, mathematical modelling, and dynamical characterization associated to this electronic chaotic oscillator. As a consequence of the investigation of different control strategies applied to Chua's circuit, a tradeoff among control objective, control energy, and model complexity is devised, which quite naturally leads to a principle that seems to be of general nature: the Information Transmission Via Control (ITVC) for nonlinear oscillators. The main purpose of the present chapter is to serve as an introductory guide to the universe of Chua's circuit control, synchronization, and mathematical modelling.

  6. Logic circuits from zero forcing

    CERN Document Server

    Burgarth, Daniel; Hogben, Leslie; Severini, Simone; Young, Michael

    2011-01-01

    We design logical circuits based on the notion of zero forcing on graphs; each gate of the circuits is a gadget in which zero forcing is performed. We show that such circuits can evaluate every monotone Boolean function. By using two vertices to encode each logical bit, we obtain universal computation. We also highlight a phenomenon of "back forcing" as a property of each function. Such a phenomenon occurs in a circuit when the input of gates which have been already used at a given time step is further modified by a computation actually performed at a later stage. Finally, we show that zero forcing can be also used to implement reversible computation. The model introduced here provides a potentially new tool in the analysis of Boolean functions, with particular attention to monotonicity.

  7. Active NE-SW Compressional Strain Within the Arabian Plate

    Science.gov (United States)

    Floyd, M. A.; ArRajehi, A.; King, R. W.; McClusky, S.; Reilinger, R. E.; Douad, M.; Sholan, J.; Bou-Rabee, F.

    2012-12-01

    Motion of the Arabian plate with respect to Eurasia has been remarkably steady over more than 25 Myr as revealed by comparison of geodetic and plate tectonic reconstructions (e.g., McQuarrie et al., 2003, GRL; ArRajehi et al., 2010, Tectonics). While internal plate deformation is small in comparison to the rate of Arabia-Eurasia convergence, the improved resolution of GPS observations indicate ~ NE-SW compressional strain that appears to affect much of the plate south of latitude ~ 30°N. Seven ~ NE-SW oriented inter-station baselines all indicated shortening at rates in the range of 0.5-2 mm/yr, for the most part with 1-sigma velocity uncertainties < 0.4 mm/yr. Plate-scale strain rates exceed 2×10-9/yr. The spatial distribution of strain can not be resolved from the sparse available data, but strain appears to extend at least to Riyadh, KSA, ~ 600 km west of the Zagros Fold and Thrust Belt that forms the eastern, collisional boundary of the Arabian plate with Eurasia (Iran). Geodetic velocities in the plate tectonic reference frame for Arabia, derived from magnetic anomalies in the Red Sea (Chu and Gordon, 1998, GJI), show no significant E-W motion for GPS stations located along the Red Sea coast (i.e., geodetic and plate tectonic spreading rates across the Red Sea agree within their resolution), in contrast to sites in the plate interior and along the east side of the plate that indicate east-directed motions. In addition, NE-SW contraction is roughly normal to ~ N-S striking major structural folds in the sedimentary rocks within the Arabian Platform. These relationships suggest that geodetically observed contraction has characterized the plate for at least the past ~ 3 Myr. Broad-scale contraction of the Arabian plate seems intuitively reasonable given that the east and north sides of the plate are dominated by active continental collision (Zagros, E Turkey/Caucasus) while the west and south sides are bordered by mid-ocean ridge spreading (Red Sea and Gulf of

  8. Chest wall reconstruction in a pediatric patient with ectopia cordis.

    Science.gov (United States)

    Mohan, Raja; Peralta, Mat; Perez, Ramiro; Rosenkranz, Eliot R; Panthaki, Zubin J

    2010-08-01

    Ectopia cordis is defined as a congenital malposition of the heart outside of the thoracic cavity. It is a rare condition, and complete ectopia cordis can be a fatal condition. Successful surgical reconstruction of this defect has been reported but is uncommon. The general approach to reconstructing the chest wall involves repositioning the heart and providing adequate coverage of the chest wall defect. We describe our experience with a patient who had complete thoracic ectopia cordis treated with staged chest wall reconstruction. The first stage involved temporary closure with synthetic material, and the second stage involved definitive reconstruction with autologous bone and cartilage grafts supported with plates. The patient has been active and without complaints since the second stage and is awaiting tracheal decannulation. There have been a few descriptions of how to approach chest wall reconstruction in patients with ectopia cordis. The 2 stage method described can be considered to repair the chest wall defect in complete thoracic ectopia cordis.

  9. Spinal sensory circuits in motion

    OpenAIRE

    2016-01-01

    International audience; The role of sensory feedback in shaping locomotion has been long debated. Recent advances in genetics and behavior analysis revealed the importance of proprioceptive pathways in spinal circuits. The mechanisms underlying peripheral mechanosensation enabled to unravel the networks that feedback to spinal circuits in order to modulate locomotion. Sensory inputs to the vertebrate spinal cord were long thought to originate from the periphery. Recent studies challenge this ...

  10. Optimizing Transmission Line Matching Circuits

    OpenAIRE

    Novak, S.

    1996-01-01

    When designing transmission line matching circuits, there exist often overlooked, additional, not much used, degree of choice in the selection of the transmission line impedance. In this work are presented results of CAD analysis for the two element transmission line matching networks, demonstrating that selecting matching circuits transmission lines with higher impedance, than usually used 50 or 75 ohms, can in most cases substantially decrease the physical dimension of the final matching ci...

  11. "大洋板块地层"的重建与意义——以藏南仲巴地区为例%The reconstruction of oceanic plate stratigraphy and its impli-cations:A case study of Zhongba area, southern Tibet

    Institute of Scientific and Technical Information of China (English)

    魏玉帅; 李亚林; 陈曦; 王成善; 李祥辉; 李鑫; 钟瀚涏

    2015-01-01

    混杂岩是古增生楔存在的标志之一,一般由枕状玄武岩、灰岩、放射虫硅质岩、硅质页岩、砂岩等混乱无序组成.目前"大洋板块地层"(OPS)运用放射虫地层学方法对混乱的增生楔断片进行重建取得了良好效果,并清晰地展示了大洋板块俯冲和洋底物质连续增生的历史.在西藏仲巴地区填图过程中,结合放射虫年代学分析鉴定结果,以OPS重建的思路和理论作为指导,重建了仲巴地区混杂岩的大洋板块地层,并恢复了该区域特提斯洋在洋中脊大洋板块增生至消亡的岩石序列,自下而上分别为侏罗纪海山玄武岩、海山覆盖物侏罗系—白垩系碳酸盐岩、海山周围沉积的侏罗系—白垩系放射虫硅质岩和硅质页岩,以及海沟附近的白垩系陆源碎屑岩等,为特提斯洋大洋板块俯冲的方向、持续时间和古大地构造环境提供了信息.%Mélange generally consists of such chaotic blocks as pillow lava, limestones, radiolarian cherts, siliceous shales and sand-stones, which tectonically contact with each other. Mélange serves as a piece of evidence of the accretionary prism (AP) related to the subduction zones. Recently, by using radiolarian biostratigraphy, the theory of ocean plate stratigraphy (OPS) is referred to as an ap-proach to the accretionary process of these blocks. In order to reconstruct the process of subduction and successive accretion of ocean floor material of Neo-tethys, the authors used the theory to mapping the accretionary prism related to the Yalung Zangbo suture zone in Zhongba area, southern Tibet. The OPS of AP in Zhongba area consists of Jurassic basalt of sea mountain, Jurassic-Creta-ceous reefs on the sea mountain, the pelagic sediments such as siliceous shales and radiolarian cherts and the Cretaceous terrigenous clasts close to the trough. This study provides new information on the direction, duration and the tectonic settings of the subduction of the Neo

  12. Should I Have Breast Reconstruction?

    Science.gov (United States)

    ... Reconstruction Surgery Breast Cancer Breast Reconstruction Surgery Should I Get Breast Reconstruction Surgery? Women who have surgery ... It usually responds well to treatment. What if I choose not to have breast reconstruction? Many women ...

  13. Plate tectonics conserves angular momentum

    Directory of Open Access Journals (Sweden)

    C. Bowin

    2009-03-01

    Full Text Available A new combined understanding of plate tectonics, Earth internal structure, and the role of impulse in deformation of the Earth's crust is presented. Plate accelerations and decelerations have been revealed by iterative filtering of the quaternion history for the Euler poles that define absolute plate motion history for the past 68 million years, and provide an unprecedented precision for plate angular rotation variations with time at 2-million year intervals. Stage poles represent the angular rotation of a plate's motion between adjacent Euler poles, and from which the maximum velocity vector for a plate can be determined. The consistent maximum velocity variations, in turn, yield consistent estimates of plate accelerations and decelerations. The fact that the Pacific plate was shown to accelerate and decelerate, implied that conservation of plate tectonic angular momentum must be globally conserved, and that is confirmed by the results shown here (total angular momentum ~1.4 E+27 kgm2s−1. Accordingly, if a plate decelerates, other plates must increase their angular momentums to compensate. In addition, the azimuth of the maximum velocity vectors yields clues as to why the "bend" in the Emperor-Hawaiian seamount trend occurred near 46 Myr. This report summarizes processing results for 12 of the 14 major tectonic plates of the Earth (except for the Juan de Fuca and Philippine plates. Plate accelerations support the contention that plate tectonics is a product of torques that most likely are sustained by the sinking of positive density anomalies due to phase changes in subducted gabbroic lithosphere at depth in the upper lower mantle (above 1200 km depth. The tectonic plates are pulled along by the sinking of these positive mass anomalies, rather than moving at near constant velocity on the crests of convection cells driven by rising heat. These results imply that spreading centers are primarily passive reactive

  14. Vehicle License Plate Recognition Syst

    Directory of Open Access Journals (Sweden)

    Meenakshi,R. B. Dubey

    2012-12-01

    Full Text Available The vehicle license plate recognition system has greater efficiency for vehicle monitoring in automatic zone access control. This Plate recognition system will avoid special tags, since all vehicles possess a unique registration number plate. A number of techniques have been used for car plate characters recognition. This system uses neural network character recognition and pattern matching of characters as two character recognition techniques. In this approach multilayer feed-forward back-propagation algorithm is used. The performance of the proposed algorithm has been tested on several car plates and provides very satisfactory results.

  15. Carboniferous paleogeographic and paleoclimatic reconstructions

    Energy Technology Data Exchange (ETDEWEB)

    Scotese, C.R. (Univ. of Texas, Arlington, TX (United States). Dept. of Geology); Raymond, A. (Texas A and M Univ., College Station, TX (United States). Dept. Geology)

    1992-01-01

    The Carboniferous was an important transitional period in earth history. The Paleozoic oceans separating the continents of Gondwana, Laurentia, Baltica, Kazakhstan, and Siberia had closed by the late Carboniferous forming the late Paleozoic supercontinent of Pangea. Plate motions which appear to have been rapid during the Early Carboniferous (6--10 cm/yr), slowed to a temperature gradient increased as the Earth's climate changed from hot-house to ice-house conditions. Sea level, which stood high during the Early Carboniferous, fell as a result of continental collision and mountain-building, and then began to rise and fall rhythmically as the South Polar ice-cap waxed and waned. These environmental changes intersected important evolutionary events, namely, the explosive colonization of the emergent land areas by plants and the rise of terrestrial vertebrates. In this paper the authors present paleogeographic reconstructions for 6 intervals during the Carboniferous. These maps illustrate the latitudinal position of the continents deduced from paleomagnetic data and the distribution of climatically restricted lithofacies (coal, bauxite, evaporite, calcrete, and tillite), the inferred location of active plate boundaries, and the changing configuration of mountains, land, shallow seas, and deep ocean basins. For each of these paleogeographic maps a climatic simulation was run using the Parametric Climate Model. These simulations predict the distribution of high and low pressure cells, prevailing wind directions, pole-to-equator temperature gradient, relative wetness/dryness, as well as zones of coastal upwelling.

  16. The Fabrication of Flow Field Plates for Direct Methanol Fuel Cell Using Lithography and Radio Frequency Sputtering.

    Science.gov (United States)

    Chang, Ho; Kao, Mu-Jung; Chen, Chih-Hao; Cho, Kun-Ching; Hsu, Chun-Yao; Chen, Zhi-Lun

    2015-08-01

    This study uses lithography to etch flow fields on a single side of a printed circuit board (PCB) and combines a flow field plate with a collector plate to make innovative anode flow field plates and cathode flow field plates for a direct methanol fuel cell (DMFC). TiO2 thin film is also sputtered on the anode flow field plate using radio frequency (RF) sputtering. The experimental results show that the prepared DMFC has a better maximum power density of 11.928 mW/cm2. Furthermore, when a TiO2 thin film is sputtered on the flow field plate of the assembled DMFC, the maximum power density is 14.426 mW/cm2, which is actually 21% more than that for a DMFC with no TiO2 thin film coated on the flow field plate.

  17. Using plate mapping to examine portion size and plate composition for large and small divided plates.

    Science.gov (United States)

    Sharp, David E; Sobal, Jeffery; Wansink, Brian

    2014-12-01

    Does the size of a plate influence the serving of all items equally, or does it influence the serving of some foods - such as meat versus vegetables - differently? To examine this question, we used the new method of plate mapping, where people drew a meal on a paper plate to examine sensitivity to small versus large three-compartment divided plates in portion size and meal composition in a sample of 109 university students. The total drawn meal area was 37% bigger on large plates than small plates, which showed that the portion of plate coverage did not differ by plate size. Men and women drew bigger vegetable portions and men drew bigger meat portions on large plates when compared to small plates. These results suggest that men and women are differentially sensitive to plate size for overall meal size and for meal composition. Implications for decreasing portion size and improving meal balance are that plate size may influence portion size and change the proportions of foods served.

  18. Neural Circuits on a Chip

    Directory of Open Access Journals (Sweden)

    Md. Fayad Hasan

    2016-09-01

    Full Text Available Neural circuits are responsible for the brain’s ability to process and store information. Reductionist approaches to understanding the brain include isolation of individual neurons for detailed characterization. When maintained in vitro for several days or weeks, dissociated neurons self-assemble into randomly connected networks that produce synchronized activity and are capable of learning. This review focuses on efforts to control neuronal connectivity in vitro and construct living neural circuits of increasing complexity and precision. Microfabrication-based methods have been developed to guide network self-assembly, accomplishing control over in vitro circuit size and connectivity. The ability to control neural connectivity and synchronized activity led to the implementation of logic functions using living neurons. Techniques to construct and control three-dimensional circuits have also been established. Advances in multiple electrode arrays as well as genetically encoded, optical activity sensors and transducers enabled highly specific interfaces to circuits composed of thousands of neurons. Further advances in on-chip neural circuits may lead to better understanding of the brain.

  19. A New Estimate for Total Offset on the Southern San Andreas Fault: Implications for Cumulative Plate Boundary Shear in the Northern Gulf of California

    Science.gov (United States)

    Darin, M. H.; Dorsey, R. J.

    2012-12-01

    Development of a consistent and balanced tectonic reconstruction for the late Cenozoic San Andreas fault (SAF) in southern California has been hindered for decades by incompatible estimates of total dextral offset based on different geologic cross-fault markers. The older estimate of 240-270 km is based on offset fluvial conglomerates of the middle Miocene Mint Canyon and Caliente Formations west of the SAF from their presumed source area in the northern Chocolate Mountains NE of the SAF (Ehlig et al., 1975; Ehlert, 2003). The second widely cited offset marker is a distinctive Triassic megaporphyritic monzogranite that has been offset 160 ± 10 km between Liebre Mountain west of the SAF and the San Bernadino Mountains (Matti and Morton, 1993). In this analysis we use existing paleocurrent data and late Miocene clockwise rotation in the eastern Transverse Ranges (ETR) to re-assess the orientation of the piercing line used in the 240 km-correlation, and present a palinspastic reconstruction that satisfies all existing geologic constraints. Our reconstruction of the Mint Canyon piercing line reduces the original estimate of 240-270 km to 195 ± 15 km of cumulative right-lateral slip on the southern SAF (sensu stricto), which is consistent with other published estimates of 185 ± 20 km based on correlative basement terranes in the Salton Trough region. Our estimate of ~195 km is consistent with the lower estimate of ~160 km on the Mojave segment because transform-parallel extension along the southwestern boundary of the ETR during transrotation produces ~25-40 km of displacement that does not affect offset markers of the Liebre/San Bernadino correlation located northwest of the ETR rotating domain. Reconciliation of these disparate estimates places an important new constraint on the total plate boundary shear that is likely accommodated in the adjacent northern Gulf of California. Global plate circuit models require ~650 km of cumulative Pacific-North America (PAC

  20. Improving global paleogeographic reconstructions since the Devonian using paleobiology

    Science.gov (United States)

    Cao, Wenchao; Zahirovic, Sabin; Williams, Simon; Flament, Nicolas; Müller, Dietmar

    2017-04-01

    Paleogeographic reconstructions are important to understand past eustatic and regional sea level change, the tectonic evolution of the planet, hydrocarbon genesis, and to constrain and interpret the dynamic topography predicted by time-dependent global mantle convection models. Several global paleogeographic compilations have been published, generally presented as static snapshots with varying temporal resolution and fixed spatial resolution. Published paleogeographic compilations are tied to a particular plate motion model, making it difficult to link them to alternative digital plate tectonic reconstructions. In order to address this issue, we developed a workflow to reverse-engineer reconstructed paleogeographies to their present-day coordinates and link them to any reconstruction model. Published paleogeographic compilations are also tied to a given dataset. We used fossil data from the Paleobiology Database to identify inconsistencies between fossils paleoenvironments and paleogeographic reconstructions, and to improve reconstructed terrestrial-marine boundaries by resolving these inconsistencies. We used the improved reconstructed paleogeographies to estimate the surface areas of global paleogeographic features (shallow marine environments, landmasses, mountains and ice sheets), to investigate the global continental flooding history since the late Paleozoic, which has inherent links to global eustasy as well as dynamic topography. Finally, we discuss the relationships between our modeled emerged land area and total continental area through time, continental growth models, and strontium isotope (87Sr/86Sr) signatures in ocean water. Our study highlights the flexibility of digital paleogeographic models linked to state-of-the-art plate tectonic reconstructions in order to better understand the interplay of continental growth and eustasy, with wider implications for understanding Earth's paleotopography, ocean circulation, and the role of mantle convection in

  1. [Breast reconstruction after mastectomy].

    Science.gov (United States)

    Ho Quoc, C; Delay, E

    2013-02-01

    The mutilating surgery for breast cancer causes deep somatic and psychological sequelae. Breast reconstruction can mitigate these effects and permit the patient to help rebuild their lives. The purpose of this paper is to focus on breast reconstruction techniques and on factors involved in breast reconstruction. The methods of breast reconstruction are presented: objectives, indications, different techniques, operative risks, and long-term monitoring. Many different techniques can now allow breast reconstruction in most patients. Clinical cases are also presented in order to understand the results we expect from a breast reconstruction. Breast reconstruction provides many benefits for patients in terms of rehabilitation, wellness, and quality of life. In our mind, breast reconstruction should be considered more as an opportunity and a positive choice (the patient can decide to do it), than as an obligation (that the patient would suffer). The consultation with the surgeon who will perform the reconstruction is an important step to give all necessary informations. It is really important that the patient could speak again with him before undergoing reconstruction, if she has any doubt. The quality of information given by medical doctors is essential to the success of psychological intervention. This article was written in a simple, and understandable way to help gynecologists giving the best information to their patients. It is maybe also possible to let them a copy of this article, which would enable them to have a written support and would facilitate future consultation with the surgeon who will perform the reconstruction.

  2. Mandibular reconstruction with composite microvascular tissue transfer

    Energy Technology Data Exchange (ETDEWEB)

    Coleman, J.J. III; Wooden, W.A. (Emory Univ. School of Medicine, Atlanta, GA (USA))

    1990-10-01

    Microvascular free tissue transfer has provided a variety of methods of restoring vascularized bone and soft tissue to difficult defects created by tumor resection and trauma. Over 7 years, 26 patients have undergone 28 free flaps for mandibular reconstruction, 15 for primary squamous cell carcinoma of the floor of the mouth or tongue, 7 for recurrent tumor, and 6 for other reasons (lymphangioma (1), infection (1), gunshot wound (1), and osteoradionecrosis (3)). Primary reconstruction was performed in 19 cases and secondary in 9. All repairs were composite flaps including 12 scapula, 5 radial forearm, 3 fibula, 2 serratus, and 6 deep circumflex iliac artery. Mandibular defects included the symphysis alone (7), symphysis and body (5), symphysis-body-ramus condyle (2), body or ramus (13), and bilateral body (1). Fourteen patients had received prior radiotherapy to adjuvant or curative doses. Eight received postoperative radiotherapy. All patients had initially successful vascularized reconstruction by clinical examination (28) and positive radionuclide scan (22 of 22). Bony stability was achieved in 25 of 26 patients and oral continence in 24 of 26. One complete flap loss occurred at 14 days. Complications of some degree developed in 22 patients including partial skin necrosis (3), orocutaneous fistula (3), plate exposure (1), donor site infection (3), fracture of reconstruction (1), and fracture of the radius (1). Microvascular transfer of bone and soft tissue allows a reliable reconstruction--despite previous radiotherapy, infection, foreign body, or surgery--in almost every situation in which mandible and soft tissue are absent. Bony union, a healed wound, and reasonable function and appearance are likely despite early fistula, skin loss, or metal plate or bone exposure.

  3. Temperature field of steel plate cooling process after plate rolling

    Directory of Open Access Journals (Sweden)

    Huijun Feng, Lingen Chen, Fengrui Sun

    2015-01-01

    Full Text Available Based on numerical calculation with Matlab, the study on cooling process after plate rolling is carried out, and the temperature field distribution of the plate varying with the time is obtained. The effects of the plate thickness, final rolling temperature, cooling water temperature, average flow rate of the cooling water, carbon content of the plate and cooling method on the plate surface and central temperatures as well as final cooling temperature are discussed. For the same cooling time, the plate surface and central temperatures as well as their temperature difference increase; with the decrease in rolling temperature and the increase in average flow rate of the cooling water, the plate surface and central temperatures decrease. Compared with the single water cooling process, the temperature difference between the plate centre and surface based on intermittent cooling is lower. In this case, the temperature uniformity of the plate is better, and the corresponding thermal stress is lower. The fitting equation of the final cooling temperature with respect to plate thickness, final rolling temperature, cooling water temperature and average flow rate of the cooling water is obtained.

  4. Particle Transport in Parallel-Plate Reactors

    Energy Technology Data Exchange (ETDEWEB)

    Rader, D.J.; Geller, A.S.

    1999-08-01

    A major cause of semiconductor yield degradation is contaminant particles that deposit on wafers while they reside in processing tools during integrated circuit manufacturing. This report presents numerical models for assessing particle transport and deposition in a parallel-plate geometry characteristic of a wide range of single-wafer processing tools: uniform downward flow exiting a perforated-plate showerhead separated by a gap from a circular wafer resting on a parallel susceptor. Particles are assumed to originate either upstream of the showerhead or from a specified position between the plates. The physical mechanisms controlling particle deposition and transport (inertia, diffusion, fluid drag, and external forces) are reviewed, with an emphasis on conditions encountered in semiconductor process tools (i.e., sub-atmospheric pressures and submicron particles). Isothermal flow is assumed, although small temperature differences are allowed to drive particle thermophoresis. Numerical solutions of the flow field are presented which agree with an analytic, creeping-flow expression for Re < 4. Deposition is quantified by use of a particle collection efficiency, which is defined as the fraction of particles in the reactor that deposit on the wafer. Analytic expressions for collection efficiency are presented for the limiting case where external forces control deposition (i.e., neglecting particle diffusion and inertia). Deposition from simultaneous particle diffusion and external forces is analyzed by an Eulerian formulation; for creeping flow and particles released from a planar trap, the analysis yields an analytic, integral expression for particle deposition based on process and particle properties. Deposition from simultaneous particle inertia and external forces is analyzed by a Lagrangian formulation, which can describe inertia-enhanced deposition resulting from particle acceleration in the showerhead. An approximate analytic expression is derived for particle

  5. Organization of the tectonic plates in the last 200 Myr (Invited)

    Science.gov (United States)

    Morra, G.; Seton, M.; Quevedo, L. E.; Müller, D.

    2013-12-01

    The present tessellation of the Earth's surface into tectonic plates displays a remarkably regular plate size distribution, described by either one (Sornette and Pisarenko, 2003) or two (Bird, 2003) statistically distinct groups, characterised by large and small plate size. A unique distribution implies a hierarchical structure from the largest to the smallest plate. Alternatively, two distributions indicate distinct evolutionary laws for large and small plates, the first tied to mantle flow, the second determined by a hierarchical fragmentation process. We analyse detailed reconstructions of plate boundaries during the last 200 Myr and find that (i) large and small plates display distinct statistical distributions, (ii) the small plates display little organisational change since 60 Ma and (iii) the large plates oscillate between heterogeneous (200-170 Ma and 65-50 Ma) and homogeneous (120-100 Ma) plate tessellations on a timescale of about 100 Myr. Heterogeneous states are reached more rapidly, while the plate configuration decays into homogeneous states following a slower asymptotic curve, suggesting that heterogeneous configurations are excited states while homogeneous tessellations are equilibrium states. We explain this evolution by proposing a model that alternates between bottom- and top-driven Earth dynamics, physically described by fluid-dynamic analogies, the Rayleigh-Benard and Bénard-Marangoni convection, respectively. We discuss the implications for true polar wander (TPW), global kinematic reorganisations (50 and 100 Ma) and the Earth's magnetic field inversion frequency. Earth's present tessellation: grey scale proportional to the logarithm of plate size. Plot: logarithm of complementary 'cumulative plate count' (Y-axis) vs. the logarithm of the plate size (X-axis). Time evolution of the 'standard deviation' of the plate size every one million years.

  6. Real Plates and Dubious Microplates

    Science.gov (United States)

    Kogan, M. G.; Steblov, G. M.

    2008-12-01

    From the onset of plate tectonics, the existence of most of the plates was never put in doubt, although the boundaries of some plates, like Africa, were later revised. There are however, two microplates in northeast Asia, the Amurian and Okhotsk, whose existence and the sense of rotation was revised several times. The rms value of plate-residual GPS velocities is 0.5-0.9 mm/a for sets of stations representing the motion of the following plates: Antarctic, Australian, Eurasian, North American, Nubian, Pacific, and South American. This value can be regarded as an upper bound on deviation of real plates from infinite stiffness. The rms value of plate-residual GPS velocities is 1.2-1.8 mm/a for the Indian, Nazca, and Somalian plates. Higher rms values for India and Nazca are attributed to the noisier data. The higher rms value for Somalia appears to arise from the distributed deformation to the east of the East African Rift; whether this statement is true can only be decided from observations of denser network in the future. From the analysis of plate-residual GPS velocities, the Canadian Arctic and northeastern Siberia belong to the North American plate. The detailed GPS survey on Sakhalin Island shows that the Sea of Okhotsk region also belongs to the North American plate while the region to the west of it belongs to the Eurasian plate. These results provide a constraint on the geometry of the North American plate and put in doubt the existence of smaller plates in northeast Asia.

  7. A Simplified View of the Geochemical Diversity Surrounding Home Plate

    Science.gov (United States)

    Yen, A. S.; Morris, R. V.; Clark, B. C.; Gellert, R.

    2008-01-01

    The Home Plate feature (Fig. 1) within the Inner Basin of the Columbia Hills consists of layered rocks and has been interpreted as an accumulation of pyroclastic deposits [1]. Samples analyzed by the Alpha Particle X-ray Spectrometer within 25 meters of the eastern margin of Home Plate exhibit a strikingly diverse range of geochemical compositions, including the highest levels of Mg, Si, K, Zn, and Ni measured at Gusev Crater. This wide range of chemical variability across the 40+ samples analyzed on and near Home Plate can be represented by contributions from only six primary components. This reconstruction is not reflected in the M ssbauer mineralogy suggesting that significant alteration of the contributing components has occurred.

  8. Global plate boundary evolution and kinematics since the late Paleozoic

    Science.gov (United States)

    Matthews, Kara J.; Maloney, Kayla T.; Zahirovic, Sabin; Williams, Simon E.; Seton, Maria; Müller, R. Dietmar

    2016-11-01

    Many aspects of deep-time Earth System models, including mantle convection, paleoclimatology, paleobiogeography and the deep Earth carbon cycle, require high-resolution plate motion models that include the evolution of the mosaic of plate boundaries through time. We present the first continuous late Paleozoic to present-day global plate model with evolving plate boundaries, building on and extending two previously published models for the late Paleozoic (410-250 Ma) and Mesozoic-Cenozoic (230-0 Ma). We ensure continuity during the 250-230 Ma transition period between the two models, update the absolute reference frame of the Mesozoic-Cenozoic model and add a new Paleozoic reconstruction for the Baltica-derived Alexander Terrane, now accreted to western North America. This 410-0 Ma open access model provides a framework for deep-time whole Earth modelling and acts as a base for future extensions and refinement. We analyse the model in terms of the number of plates, predicted plate size distribution, plate and continental root mean square (RMS) speeds, plate velocities and trench migration through time. Overall model trends share many similarities to those for recent times, which we use as a first order benchmark against which to compare the model and identify targets for future model refinement. Except for during the period 260-160 Ma, the number of plates (16-46) and ratio of "large" plates (≥ 107.5 km2) to smaller plates ( 2.7-6.6) are fairly similar to present-day values (46 and 6.6, respectively), with lower values occurring during late Paleozoic assembly and growth of Pangea. This temporal pattern may also reflect difficulties in reconstructing small, now subducted oceanic plates further back in time, as well as whether a supercontinent is assembling or breaking up. During the 260-160 Ma timeframe the model reaches a minima in the number of plates, in contrast to what we would expect during initial Pangea breakup and thus highlighting the need for refinement

  9. Difference-Equation/Flow-Graph Circuit Analysis

    Science.gov (United States)

    Mcvey, I. M.

    1988-01-01

    Numerical technique enables rapid, approximate analyses of electronic circuits containing linear and nonlinear elements. Practiced in variety of computer languages on large and small computers; for circuits simple enough, programmable hand calculators used. Although some combinations of circuit elements make numerical solutions diverge, enables quick identification of divergence and correction of circuit models to make solutions converge.

  10. Multi-Layer E-Textile Circuits

    Science.gov (United States)

    Dunne, Lucy E.; Bibeau, Kaila; Mulligan, Lucie; Frith, Ashton; Simon, Cory

    2012-01-01

    Stitched e-textile circuits facilitate wearable, flexible, comfortable wearable technology. However, while stitched methods of e-textile circuits are common, multi-layer circuit creation remains a challenge. Here, we present methods of stitched multi-layer circuit creation using accessible tools and techniques.

  11. 30 CFR 56.6403 - Branch circuits.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Branch circuits. 56.6403 Section 56.6403... Blasting § 56.6403 Branch circuits. (a) If electric blasting includes the use of branch circuits, each branch shall be equipped with a safety switch or equivalent method to isolate the circuits to be used....

  12. Equivalence Checking of Hierarchical Combinational Circuits

    DEFF Research Database (Denmark)

    Williams, Poul Frederick; Hulgaard, Henrik; Andersen, Henrik Reif

    1999-01-01

    This paper presents a method for verifying that two hierarchical combinational circuits implement the same Boolean functions. The key new feature of the method is its ability to exploit the modularity of circuits to reuse results obtained from one part of the circuits in other parts. We demonstrate...... our method on large adder and multiplier circuits....

  13. The improvements on reactor building liner plate erection work

    Energy Technology Data Exchange (ETDEWEB)

    Roh, Myungsub; Choi, Sangmoo [Ulchin Nuclear Division, KHNP, Seoul (Korea, Republic of)

    2002-04-15

    The pressurized water reactor, with its primary cooling circuit and steam generators, is housed in a cylindrical building. This 'containment' building is 44m in diameter and 80m high, and has a hemispherical or dome roof. A 6mm steel plate lines the entire interior of this containment building. This steel lining covers the floors, walls, dome and is made gas tight. There are more than 160 penetrations in the containment building for: equipment and personnel access, piping and electrical services. There are also over 370 field welded embedments fixed to the steel liner plate. Reducing construction costs of commercial nuclear power plants is essential in order to expand the future use of nuclear energy. One of the major components of reducing construction costs is the continuous improvement in construction technology. This is also essential in order to increase the nuclear culture in Quality Assurance of nuclear power plants. These improvements can make up for shortages in skilled craft labor necessary during site construction. In this paper, a number of improvements for the containment building steel liner plate fabrication and erection work will be described; adoption of flux core arc welding process, welding improvement in thickened liner plates, prefabrication of reactor cavity wall liner plates in the yard and optimization of the number of field welded embedments. Eventually these improvements may provide cost reduction and may allow reduction in the critical path schedule.

  14. Plate Full of Color

    Centers for Disease Control (CDC) Podcasts

    2008-08-04

    The Eagle Books are a series of four books that are brought to life by wise animal characters - Mr. Eagle, Miss Rabbit, and Coyote - who engage Rain That Dances and his young friends in the joy of physical activity, eating healthy foods, and learning from their elders about health and diabetes prevention. Plate Full of Color teaches the value of eating a variety of colorful and healthy foods.  Created: 8/4/2008 by National Center for Chronic Disease Prevention and Health Promotion (NCCDPHP).   Date Released: 8/5/2008.

  15. Dynamics of Tectonic Plates

    CERN Document Server

    Pechersky, E; Sadowski, G; Yambartsev, A

    2014-01-01

    We suggest a model that describes a mutual dynamic of tectonic plates. The dynamic is a sort of stick-slip one which is modeled by a Markov random process. The process defines a microlevel of the dynamic. A macrolevel is obtained by a scaling limit which leads to a system of integro-differential equations which determines a kind of mean field systems. Conditions when Gutenberg-Richter empirical law are presented on the mean field level. These conditions are rather universal and do not depend on features of resistant forces.

  16. Dynamics of Tectonic Plates

    OpenAIRE

    2014-01-01

    We suggest a model that describes a mutual dynamic of tectonic plates. The dynamic is a sort of stick-slip one which is modeled by a Markov random process. The process defines a microlevel of the dynamic. A macrolevel is obtained by a scaling limit which leads to a system of integro-differential equations which determines a kind of mean field systems. Conditions when Gutenberg-Richter empirical law are presented on the mean field level. These conditions are rather universal and do not depend ...

  17. Cryo-EM single particle analysis with the Volta phase plate.

    Science.gov (United States)

    Danev, Radostin; Baumeister, Wolfgang

    2016-01-01

    We present a method for in-focus data acquisition with a phase plate that enables near-atomic resolution single particle reconstructions. Accurate focusing is the determining factor for obtaining high quality data. A double-area focusing strategy was implemented in order to achieve the required precision. With this approach we obtained a 3.2 Å resolution reconstruction of the Thermoplasma acidophilum 20S proteasome. The phase plate matches or slightly exceeds the performance of the conventional defocus approach. Spherical aberration becomes a limiting factor for achieving resolutions below 3 Å with in-focus phase plate images. The phase plate could enable single particle analysis of challenging samples in terms of small size, heterogeneity and flexibility that are difficult to solve by the conventional defocus approach.

  18. Comparison between four piezoelectric energy harvesting circuits

    Institute of Scientific and Technical Information of China (English)

    Jinhao QIU; Hao JIANG; Hongli JI; Kongjun ZHU

    2009-01-01

    This paper investigates and compares the efficiencies of four different interfaces for vibration-based energy harvesting systems. Among those four circuits, two circuits adopt the synchronous switching technique, in which the circuit is switched synchronously with the vibration. In this study, a simple source-less trigger circuit used to control the synchronized switch is proposed and two interface circuits of energy harvesting systems are designed based on the trigger circuit. To validate the effectiveness of the proposed circuits, an experimental system was established and the power harvested by those circuits from a vibration beam was measured. Experimental results show that the two new circuits can increase the harvested power by factors 2.6 and 7, respectively, without consuming extra power in the circuits.

  19. Using Combinational Circuits for Control Purposes

    Directory of Open Access Journals (Sweden)

    Maher A. Nabulsi

    2009-01-01

    Full Text Available Problem statement: Combinational circuits are used in computers for generating binary control decisions and for providing digital components for data processing. Approach: The use of combinational circuits and logic gates to control other circuits was discussed. Different systems that use logic gates, multiplexers, decoders and encoders to control different circuits were presented. This study presented a design and implementation of some combinational circuits such as a decoder, an encoder, a multiplexer, a bus system and read/write memory operations. Results: When we connected some types of combinational circuits to the inputs/outputs of digital circuit, these combinational circuits can help us to manage and flow a different types of control signals through a large digital circuit. Conclusion: Many combinational circuits had a good function which can be used for controlling different parts of any digital system and they produce a suitable way to transfer a control signals between different digital components of any large digital system.

  20. Progress in timing Resistive Plate Chambers

    Energy Technology Data Exchange (ETDEWEB)

    Blanco, A. [Laboratorio de Instrumentacao e Fisica Experimental de Particulas (LIP), Universidade de Coimbra, Dep. de Fisica, 3004-516 Coimbra (Portugal); Carolino, N. [Laboratorio de Instrumentacao e Fisica Experimental de Particulas (LIP), Universidade de Coimbra, Dep. de Fisica, 3004-516 Coimbra (Portugal); Correia, C.M.B.A. [Laboratorio de Instrumentacao e Fisica Experimental de Particulas (LIP), Universidade de Coimbra, Dep. de Fisica, 3004-516 Coimbra (Portugal)] [and others

    2004-12-11

    Timing RPCs are Resistive Plate Chambers made with glass and metal electrodes separated by precision spacers. Typical gas gaps are a few hundred micrometers wide. Such counters were introduced in 1999 and have since reached timing accuracies below 50ps {sigma} with efficiencies above 99% for MIPs. Applications in high-energy physics have already taken place with several more under study.Some recent developments include the extension of the counting rate capability by over one order of magnitude, to 25kHz/cm2, with time resolutions below 100ps {sigma}. A prototype RPC-based Positron Emission Tomograph yielded a reconstructed point-source resolution of 0.6 mm FWHM and a modified timing RPC design, featuring 50{mu}m pitch anode strips, allowed to reach extremely good position resolution for hard X-rays in digital readout mode.An analytically solvable model has allowed us to clarify the basic factors influencing the time resolution.

  1. Neuregulin 3 Mediates Cortical Plate Invasion and Laminar Allocation of GABAergic Interneurons

    Directory of Open Access Journals (Sweden)

    Giorgia Bartolini

    2017-01-01

    Full Text Available Neural circuits in the cerebral cortex consist of excitatory pyramidal cells and inhibitory interneurons. These two main classes of cortical neurons follow largely different genetic programs, yet they assemble into highly specialized circuits during development following a very precise choreography. Previous studies have shown that signals produced by pyramidal cells influence the migration of cortical interneurons, but the molecular nature of these factors has remained elusive. Here, we identified Neuregulin 3 (Nrg3 as a chemoattractive factor expressed by developing pyramidal cells that guides the allocation of cortical interneurons in the developing cortical plate. Gain- and loss-of-function approaches reveal that Nrg3 modulates the migration of interneurons into the cortical plate in a process that is dependent on the tyrosine kinase receptor ErbB4. Perturbation of Nrg3 signaling in conditional mutants leads to abnormal lamination of cortical interneurons. Nrg3 is therefore a critical mediator in the assembly of cortical inhibitory circuits.

  2. Instrumentation and test gear circuits manual

    CERN Document Server

    Marston, R M

    2013-01-01

    Instrumentation and Test Gear Circuits Manual provides diagrams, graphs, tables, and discussions of several types of practical circuits. The practical circuits covered in this book include attenuators, bridges, scope trace doublers, timebases, and digital frequency meters. Chapter 1 discusses the basic instrumentation and test gear principles. Chapter 2 deals with the design of passive attenuators, and Chapter 3 with passive and active filter circuits. The subsequent chapters tackle 'bridge' circuits, analogue and digital metering techniques and circuitry, signal and waveform generation, and p

  3. CMS Resistive plate Champers

    CERN Document Server

    Zainab, Karam

    2013-01-01

    There are many types of gas detectors which are used in CERN in LHC project, There is a main parts for the gas detectors which must be in all gas detectors types like Multiwire proportional chambers, such as the micromesh gaseous structure chamber (the MicroMegas), Gas-electron multiplier (GEM) detector, Resistive Plate Champers... Compact Muon Solenoid (CMS) experiment detecting muons which are powerful tool for recognizing signatures of interesting physics processes. The CMS detector uses: drift tube (DT), cathode strip chamber (CSC) and resistive plate chamber (RPC). Building RPC’s was my project in summer student program (hardware). RPC’s have advantages which are triggering detector and Excellent time resolution which reinforce the measurement of the correct beam crossing time. RPC’s Organized in stations :  RPC barrel (RB) there are 4 stations, namely RB1, RB2, RB3, and RB4  While in the RPC endcap (RE) the 3 stations are RE1, RE2, and RE3. In the endcaps a new starion will be added and this...

  4. 30 CFR 75.601-1 - Short circuit protection; ratings and settings of circuit breakers.

    Science.gov (United States)

    2010-07-01

    ... of circuit breakers. 75.601-1 Section 75.601-1 Mineral Resources MINE SAFETY AND HEALTH... Trailing Cables § 75.601-1 Short circuit protection; ratings and settings of circuit breakers. Circuit breakers providing short circuit protection for trailing cables shall be set so as not to exceed...

  5. 49 CFR 236.5 - Design of control circuits on closed circuit principle.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Design of control circuits on closed circuit..., AND APPLIANCES Rules and Instructions: All Systems General § 236.5 Design of control circuits on closed circuit principle. All control circuits the functioning of which affects safety of train...

  6. 30 CFR 77.506 - Electric equipment and circuits; overload and short-circuit protection.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Electric equipment and circuits; overload and short-circuit protection. 77.506 Section 77.506 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION... circuits; overload and short-circuit protection. Automatic circuit-breaking devices or fuses of the...

  7. 30 CFR 77.800 - High-voltage circuits; circuit breakers.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false High-voltage circuits; circuit breakers. 77.800... COAL MINES Surface High-Voltage Distribution § 77.800 High-voltage circuits; circuit breakers. High-voltage circuits supplying power to portable or mobile equipment shall be protected by suitable...

  8. Logic circuits from zero forcing.

    Science.gov (United States)

    Burgarth, Daniel; Giovannetti, Vittorio; Hogben, Leslie; Severini, Simone; Young, Michael

    We design logic circuits based on the notion of zero forcing on graphs; each gate of the circuits is a gadget in which zero forcing is performed. We show that such circuits can evaluate every monotone Boolean function. By using two vertices to encode each logical bit, we obtain universal computation. We also highlight a phenomenon of "back forcing" as a property of each function. Such a phenomenon occurs in a circuit when the input of gates which have been already used at a given time step is further modified by a computation actually performed at a later stage. Finally, we show that zero forcing can be also used to implement reversible computation. The model introduced here provides a potentially new tool in the analysis of Boolean functions, with particular attention to monotonicity. Moreover, in the light of applications of zero forcing in quantum mechanics, the link with Boolean functions may suggest a new directions in quantum control theory and in the study of engineered quantum spin systems. It is an open technical problem to verify whether there is a link between zero forcing and computation with contact circuits.

  9. Introduction to lethal circuit transformations

    Science.gov (United States)

    Fišer, Petr; Schmidt, Jan

    2015-12-01

    Logic optimization is a process that takes a logic circuit description (Boolean network) as an input and tries to refine it, to reduce its size and/or depth. An ideal optimization process should be able to devise an optimum implementation of a network in a reasonable time, given any circuit structure at the input. However, there are cases where it completely fails to produce even near-optimum solutions. Such cases are typically induced by non-standard circuit structure modifications. Surprisingly enough, such deviated structures are frequently present in standard benchmark sets too. We may only wonder whether it is an intention of the benchmarks creators, or just an unlucky coincidence. Even though synthesis tools should be primarily well suited for practical circuits, there is no guarantee that, e.g., a higher-level synthesis process will not generate such unlucky structures. Here we present examples of circuit transformations that lead to failure of most of state-of-the-art logic synthesis and optimization processes, both academic and commercial, and suggest actions to mitigate the disturbing effects.

  10. Dynamical compensation in physiological circuits.

    Science.gov (United States)

    Karin, Omer; Swisa, Avital; Glaser, Benjamin; Dor, Yuval; Alon, Uri

    2016-11-08

    Biological systems can maintain constant steady-state output despite variation in biochemical parameters, a property known as exact adaptation. Exact adaptation is achieved using integral feedback, an engineering strategy that ensures that the output of a system robustly tracks its desired value. However, it is unclear how physiological circuits also keep their output dynamics precise-including the amplitude and response time to a changing input. Such robustness is crucial for endocrine and neuronal homeostatic circuits because they need to provide a precise dynamic response in the face of wide variation in the physiological parameters of their target tissues; how such circuits compensate their dynamics for unavoidable natural fluctuations in parameters is unknown. Here, we present a design principle that provides the desired robustness, which we call dynamical compensation (DC). We present a class of circuits that show DC by means of a nonlinear feedback loop in which the regulated variable controls the functional mass of the controlling endocrine or neuronal tissue. This mechanism applies to the control of blood glucose by insulin and explains several experimental observations on insulin resistance. We provide evidence that this mechanism may also explain compensation and organ size control in other physiological circuits.

  11. Spectral Reconstruction for Obtaining Virtual Hyperspectral Images

    Science.gov (United States)

    Perez, G. J. P.; Castro, E. C.

    2016-12-01

    Hyperspectral sensors demonstrated its capabalities in identifying materials and detecting processes in a satellite scene. However, availability of hyperspectral images are limited due to the high development cost of these sensors. Currently, most of the readily available data are from multi-spectral instruments. Spectral reconstruction is an alternative method to address the need for hyperspectral information. The spectral reconstruction technique has been shown to provide a quick and accurate detection of defects in an integrated circuit, recovers damaged parts of frescoes, and it also aids in converting a microscope into an imaging spectrometer. By using several spectral bands together with a spectral library, a spectrum acquired by a sensor can be expressed as a linear superposition of elementary signals. In this study, spectral reconstruction is used to estimate the spectra of different surfaces imaged by Landsat 8. Four atmospherically corrected surface reflectance from three visible bands (499 nm, 585 nm, 670 nm) and one near-infrared band (872 nm) of Landsat 8, and a spectral library of ground elements acquired from the United States Geological Survey (USGS) are used. The spectral library is limited to 420-1020 nm spectral range, and is interpolated at one nanometer resolution. Singular Value Decomposition (SVD) is used to calculate the basis spectra, which are then applied to reconstruct the spectrum. The spectral reconstruction is applied for test cases within the library consisting of vegetation communities. This technique was successful in reconstructing a hyperspectral signal with error of less than 12% for most of the test cases. Hence, this study demonstrated the potential of simulating information at any desired wavelength, creating a virtual hyperspectral sensor without the need for additional satellite bands.

  12. Mantle flow geometry from ridge to trench beneath the Gorda-Juan de Fuca plate system

    Science.gov (United States)

    Martin-Short, Robert; Allen, Richard M.; Bastow, Ian D.; Totten, Eoghan; Richards, Mark A.

    2015-12-01

    Tectonic plates are underlain by a low-viscosity mantle layer, the asthenosphere. Asthenospheric flow may be induced by the overriding plate or by deeper mantle convection. Shear strain due to this flow can be inferred using the directional dependence of seismic wave speeds--seismic anisotropy. However, isolation of asthenospheric signals is challenging; most seismometers are located on continents, whose complex structure influences the seismic waves en route to the surface. The Cascadia Initiative, an offshore seismometer deployment in the US Pacific Northwest, offers the opportunity to analyse seismic data recorded on simpler oceanic lithosphere. Here we use measurements of seismic anisotropy across the Juan de Fuca and Gorda plates to reconstruct patterns of asthenospheric mantle shear flow from the Juan de Fuca mid-ocean ridge to the Cascadia subduction zone trench. We find that the direction of fastest seismic wave motion rotates with increasing distance from the mid-ocean ridge to become aligned with the direction of motion of the Juan de Fuca Plate, implying that this plate influences mantle flow. In contrast, asthenospheric mantle flow beneath the Gorda Plate does not align with Gorda Plate motion and instead aligns with the neighbouring Pacific Plate motion. These results show that asthenospheric flow beneath the small, slow-moving Gorda Plate is controlled largely by advection due to the much larger, faster-moving Pacific Plate.

  13. Localised Plate Motion on Venus

    Science.gov (United States)

    Ghail, R. C.

    1996-03-01

    The volcanic and tectonic features observed in Dali Vinculum, Parga Vinculum and Imdr Regio are concentrated at long, narrow, curvilinear zones, with relatively minor volcanism and tectonism between these zones. These zones, whilst more diffuse than terrestrial plate boundaries, nevertheless define the margins of tectonic plates. In contrast to Earth, however, it appears that venusian plates are neither created nor destroyed by lateral motion. Rather, plates are thinned and intruded at vincula plate boundaries, vertically accreted by small-scale intra-plate (planitia) volcanism and perhaps destroyed by delamination of thickened crust in tesserae and montane regions such as Thetis Regio and Ishtar Terra. The diversity in age both between and within these three areas together with the evidence for infrequent, small scale resurfacing in the planitiae are difficult to reconcile with a non-uniformitarian geological process.

  14. Tectonics of the Easter plate

    Science.gov (United States)

    Engeln, J. F.; Stein, S.

    1984-01-01

    A new model for the Easter plate is presented in which rift propagation has resulted in the formation of a rigid plate between the propagating and dying ridges. The distribution of earthquakes, eleven new focal mechanisms, and existing bathymetric and magnetic data are used to describe the tectonics of this area. Both the Easter-Nazca and Easter-Pacific Euler poles are sufficiently close to the Easter plate to cause rapid changes in rates and directions of motion along the boundaries. The east and west boundaries are propagating and dying ridges; the southwest boundary is a slow-spreading ridge and the northern boundary is a complex zone of convergent and transform motion. The Easter plate may reflect the tectonics of rift propagation on a large scale, where rigid plate tectonics requires boundary reorientation. Simple schematic models to illustrate the general features and processes which occur at plates resulting from large-scale rift propagation are used.

  15. Tectonics of the Easter plate

    Science.gov (United States)

    Engeln, J. F.; Stein, S.

    1984-01-01

    A new model for the Easter plate is presented in which rift propagation has resulted in the formation of a rigid plate between the propagating and dying ridges. The distribution of earthquakes, eleven new focal mechanisms, and existing bathymetric and magnetic data are used to describe the tectonics of this area. Both the Easter-Nazca and Easter-Pacific Euler poles are sufficiently close to the Easter plate to cause rapid changes in rates and directions of motion along the boundaries. The east and west boundaries are propagating and dying ridges; the southwest boundary is a slow-spreading ridge and the northern boundary is a complex zone of convergent and transform motion. The Easter plate may reflect the tectonics of rift propagation on a large scale, where rigid plate tectonics requires boundary reorientation. Simple schematic models to illustrate the general features and processes which occur at plates resulting from large-scale rift propagation are used.

  16. Cosmic Tidal Reconstruction

    CERN Document Server

    Zhu, Hong-Ming; Yu, Yu; Er, Xinzhong; Chen, Xuelei

    2015-01-01

    The gravitational coupling of a long wavelength tidal field with small scale density fluctuations leads to anisotropic distortions of the locally measured small scale matter correlation function. Since the local correlation function is statistically isotropic in the absence of such tidal interactions, the tidal distortions can be used to reconstruct the long wavelength tidal field and large scale density field in analogy with the cosmic microwave background lensing reconstruction. In this paper we present in detail a formalism for the cosmic tidal reconstruction and test the reconstruction in numerical simulations. We find that the density field on large scales can be reconstructed with good accuracy and the cross correlation coefficient between the reconstructed density field and the original density field is greater than 0.9 on large scales ($k\\lesssim0.1h/\\mathrm{Mpc}$). This is useful in the 21cm intensity mapping survey, where the long wavelength radial modes are lost due to foreground subtraction proces...

  17. Circuit bridging of digital equipment caused by smoke from a cable fire

    Energy Technology Data Exchange (ETDEWEB)

    Tanaka, T.J.; Anderson, D.J.

    1997-03-01

    Advanced reactor systems are likely to use protection systems with digital electronics that ideally should be resistant to environmental hazards, including smoke from possible cable fires. Previous smoke tests have shown that digital safety systems can fail even at relatively low levels of smoke density and that short-term failures are likely to be caused by circuit bridging. Experiments were performed to examine these failures, with a focus on component packaging and protection schemes. Circuit bridging, which causes increased leakage currents and arcs, was gauged by measuring leakage currents among the leads of component packages. The resistance among circuit leads typically varies over a wide range, depending on the nature of the circuitry between the pins, bias conditions, circuit board material, etc. Resistance between leads can be as low as 20 k{Omega} and still be good, depending on the component. For these tests, the authors chose a printed circuit board and components that normally have an interlead resistance above 10{sup 12} {Omega}, but if the circuit is exposed to smoke, circuit bridging causes the resistance to fall below 10{sup 3} {Omega}. Plated-through-hole (PTH) and surface-mounted (SMT) packages were exposed to a series of different smoke environments using a mixture of environmentally qualified cables for fuel. Conformal coatings and enclosures were tested as circuit protection methods. High fuel levels, high humidity, and high flaming burns were the conditions most likely to cause circuit bridging. The inexpensive conformal coating that was tested - an acrylic spray - reduced leakage currents, but enclosure in a chassis with a fan did not. PTH packages were more resistant to smoke-induced circuit bridging than SMT packages. Active components failed most often in tests where the leakage currents were high, but failure did not always accompany high leakage currents.

  18. Aluminum Manganese Molten Salt Plating

    Science.gov (United States)

    2006-06-01

    Dry fixture thoroughly with the air gun. Be especially careful to dry water out of crevices. Note: water is a contaminant to the plating process...easily destroyed if blown with the air. Be especially careful to dry water out of crevices. Note: water is a contaminant to the plating process and...especially careful to dry water out of crevices. 13. Carefully remove part from fixture. If residual plating solution is present at attachments points

  19. Electronically Tunable Sinusoidal Oscillator Circuit

    Directory of Open Access Journals (Sweden)

    Sudhanshu Maheshwari

    2012-01-01

    Full Text Available This paper presents a novel electronically tunable third-order sinusoidal oscillator synthesized from a simple topology, employing current-mode blocks. The circuit is realized using the active element: Current Controlled Conveyors (CCCIIs and grounded passive components. The new circuit enjoys the advantages of noninteractive electronically tunable frequency of oscillation, use of grounded passive components, and the simultaneous availability of three sinusoidal voltage outputs. Bias current generation scheme is given for the active elements used. The circuit exhibits good high frequency performance. Nonideal and parasitic study has also been carried out. Wide range frequency tuning is shown with the bias current. The proposed theory is verified through extensive PSPICE simulations using 0.25 μm CMOS process parameters.

  20. Optimization of reversible sequential circuits

    CERN Document Server

    Sayem, Abu Sadat Md

    2010-01-01

    In recent years reversible logic has been considered as an important issue for designing low power digital circuits. It has voluminous applications in the present rising nanotechnology such as DNA computing, Quantum Computing, low power VLSI and quantum dot automata. In this paper we have proposed optimized design of reversible sequential circuits in terms of number of gates, delay and hardware complexity. We have designed the latches with a new reversible gate and reduced the required number of gates, garbage outputs, and delay and hardware complexity. As the number of gates and garbage outputs increase the complexity of reversible circuits, this design will significantly enhance the performance. We have proposed reversible D-latch and JK latch which are better than the existing designs available in literature.