WorldWideScience

Sample records for plate avalanche detectors

  1. A position sensitive parallel plate avalanche fission detector for use in particle induced fission coincidence measurements

    NARCIS (Netherlands)

    Plicht, J. van der

    1980-01-01

    A parallel plate avalanche detector developed for the detection of fission fragments in particle induced fission reactions is described. The active area is 6 × 10 cm2; it is position sensitive in one dimension with a resolution of 2.5 mm. The detector can withstand a count rate of 25000 fission

  2. A parallel plate avalanche detector system for the localization of relativistic heavy ions

    Energy Technology Data Exchange (ETDEWEB)

    Burgei, R.; Demoulins, M.; Cavata, C.; Fanet, H.; Gosset, J.; Le Merdy, A.; L' Hote, D.; Lucas, B.; Lugol, J.C.; Poitou, J.; Valette, O. (CEA Centre d' Etudes Nucleaires de Saclay, 91 - Gif-sur-Yvette (France). Dept. de Physique Nucleaire); Lemaire, M.C. (Institut National de Physique Nucleaire et de Physique des Particules de Saclay, 91 - Gif-sur-Yvette (France) CEA Centre d' Etudes Nucleaires de Saclay, 91 - Gif-sur-Yvette (France). Inst. de Recherche Fondamentale (IRF))

    1990-02-15

    Parallel plate avalanche counters have been designed and used for the localization of relativistic heavy ions. They have been tested with alpha particles from a {sup 241}Am source. They have been used with the heavy-ion beams from Saturne in conjunction with the 4{pi} detector Diogene. They provide an accurate measurement of the vertex position with high efficiency. (orig.).

  3. Nanopillar Optical Antenna Avalanche Detectors

    Science.gov (United States)

    2014-08-30

    68 , (11), 10. 51. Adachi, S., Properties of aluminium gallium ...bandwidth products > 100 GHz. 2 UNIVERSITY OF CALIFORNIA Los Angeles Nanopillar Optical Antenna Avalanche Detectors A dissertation... products > 100 GHz. 6 iii The dissertation of Pradeep

  4. High gain multigap avalanche detectors for Cerenkov ring imaging

    Energy Technology Data Exchange (ETDEWEB)

    Gilmore, R.S.; Lavender, W.M.; Leith, D.W.G.S.; Williams, S.H.

    1980-10-01

    We report on a continuing study of multigap parallel plate avalanche chambers, primarily as photoelectron detectors for use with Cerenkov ring imaging counters. By suitable control of the fields in successive gaps and by introducing screens to reduce photon feedback to the cathode the gain many be increased considerably. We have obtained gains in excess of 6 x 10/sup 7/ for photoelectrons with a good pulse height spectrum and expect to increase this further. We discuss the use of resistive anodes to give avalanche positions in two dimensions by charge division.

  5. TCAD simulation of Low Gain Avalanche Detectors

    Science.gov (United States)

    Dalal, Ranjeet; Jain, Geetika; Bhardwaj, Ashutosh; Ranjan, Kirti

    2016-11-01

    In the present work, detailed simulation using Technology Computer Aided Design (TCAD) tool, Silvaco for non-irradiated and irradiated LGAD (Low Gain Avalanche Detector) devices has been carried out. The effects of different design parameters and proton irradiation on LGAD operation are discussed in detail. An already published effective two trap bulk damage model is used to simulate the radiation damage without implementing any acceptor removal term. The TCAD simulation for irradiated LGAD devices produce decreasing gain with increasing fluence, similar to the measurement results. The space charge density and electric field distribution are used to illustrate the possible reasons for the degradation of gain of the irradiated LGAD devices.

  6. Negative Avalanche Feedback Detectors for Photon-Counting Optical Communications

    Science.gov (United States)

    Farr, William H.

    2009-01-01

    Negative Avalanche Feedback photon counting detectors with near-infrared spectral sensitivity offer an alternative to conventional Geiger mode avalanche photodiode or phototube detectors for free space communications links at 1 and 1.55 microns. These devices demonstrate linear mode photon counting without requiring any external reset circuitry and may even be operated at room temperature. We have now characterized the detection efficiency, dark count rate, after-pulsing, and single photon jitter for three variants of this new detector class, as well as operated these uniquely simple to use devices in actual photon starved free space optical communications links.

  7. Negative Avalanche Feedback Detectors for Photon-Counting Optical Communications

    Science.gov (United States)

    Farr, William H.

    2009-01-01

    Negative Avalanche Feedback photon counting detectors with near-infrared spectral sensitivity offer an alternative to conventional Geiger mode avalanche photodiode or phototube detectors for free space communications links at 1 and 1.55 microns. These devices demonstrate linear mode photon counting without requiring any external reset circuitry and may even be operated at room temperature. We have now characterized the detection efficiency, dark count rate, after-pulsing, and single photon jitter for three variants of this new detector class, as well as operated these uniquely simple to use devices in actual photon starved free space optical communications links.

  8. An Ion Beam Tracking System based on a Parallel Plate Avalanche Counter

    Directory of Open Access Journals (Sweden)

    Carter I. P.

    2013-12-01

    Full Text Available A pair of twin position-sensitive parallel plate avalanche counters have been developed at the Australian National University as a tracking system to aid in the further rejection of unwanted beam particles from a 6.5 T super conducting solenoid separator named SOLEROO. Their function is to track and identify each beam particle passing through the detectors on an event-by-event basis. In-beam studies have been completed and the detectors are in successful operation, demonstrating the tracking capability. A high efficiency 512-pixelwide-angle silicon detector array will then be integrated with the tracking system for nuclear reactions studies of radioactive ions.

  9. Progress in simulations of micropattern gas avalanche detectors

    CERN Document Server

    Cwetanski, Peter

    2000-01-01

    Helpful for a better understanding of the intrinsic processes in the various gas avalanche detectors are simulations, involving three- dimensional Finite Element Method (FEM) field map computations in order to describe the more and more complex geometries. Drift, multiplication and attachment procedures are simulated using Monte Carlo techniques. Recent results show a remarkable agreement with gain and energy resolution measurements thanks to the refined computations of gas transport properties and improved avalanching models. As examples the influence of wire eccentricity on gas gain and energy resolution in the ATLAS TRT straws is shown as well as performed studies of the Micromegas detector. 8 Refs.

  10. Micro-channel plate detector

    Science.gov (United States)

    Elam, Jeffrey W.; Lee, Seon W.; Wang, Hsien -Hau; Pellin, Michael J.; Byrum, Karen; Frisch, Henry J.

    2015-09-22

    A method and system for providing a micro-channel plate detector. An anodized aluminum oxide membrane is provided and includes a plurality of nanopores which have an Al coating and a thin layer of an emissive oxide material responsive to incident radiation, thereby providing a plurality of radiation sensitive channels for the micro-channel plate detector.

  11. Detector Physics of Resistive Plate Chambers

    CERN Document Server

    Lippmann, Christian; Riegler, W

    2003-01-01

    Resistive Plate Chambers (RPCs) are gaseous parallel plate avalanche detectors that implement electrodes made from a material with a high volume resistivity between 10^7 and 10^12 Ohm cm. Large area RPCs with 2mm single gaps operated in avalanche mode provide above 98% efficiency and a time resolution of around 1ns up to a flux of several kHz/cm2. These Trigger RPCs will, as an example, equip the muon detector system of the ATLAS experiment at CERN on an area of 3650m2 and with 355.000 independent read out channels. Timing RPCs with a gas gap of 0.2 to 0.3mm are widely used in multi gap configurations and provide 99% efficiency and time resolution down to 50ps. While their performance is comparable to existing scintillator-based Time-Of-Flight (TOF) technology, Timing RPCs feature a significantly, up to an order of magnitude, lower price per channel. They will for example equip the 176m2 TOF barrel of the ALICE experiment at CERN with 160.000 independent read out cells. RPCs were originally operated in stream...

  12. Geiger-mode avalanche photodiodes for Cherenkov detectors

    Energy Technology Data Exchange (ETDEWEB)

    Renker, D [Paul Scherrer Institue, 5232 Villigen PSI (Switzerland)], E-mail: dieter.renker@psi.ch

    2010-01-15

    Semiconductor photo sensors have in comparison with other detectors used in the ring image Cherenkov (RICH) and in the internally reflected Cherenkov light (DIRC) technique, photomultipier tubes and their derivates, a number of advantages: they have high photon detection efficiency ( {approx} 50%), are insensitive to magnetic fields, operate at low voltages and allow a compact, light and robust design. Specially the relatively new Geiger-mode avalanche photodiode (also called silicon photomultiplier) is a promising candidate for a detector of Cherenkov photons. The state of the development and the problems of this device will be described.

  13. Avalanche Photodiodes as Fast X-ray Detectors.

    Science.gov (United States)

    Kishimoto, S

    1998-05-01

    An avalanche photodiode (APD) detector provides a sub-nanosecond time resolution and an output rate of more than 10(8) counts s(-1) of synchrotron X-rays. Moreover, the APD has the advantage of low noise. A review of recent developments of detectors using APD devices designed for X-ray experiments is presented in this paper. One of the detectors has an excellent time response of 100 ps resolution and a narrow width on its response function, 1.4 ns at 10(-5) maximum. The other consists of a stack of four diodes and has a transmission structure. The stacked detector improved the efficiency for X-rays, e.g. 55% at 16.53 keV. The output rates reached more than 10(8) counts s(-1) per device.

  14. Avalanche photodiode based detector for beam emission spectroscopy.

    Science.gov (United States)

    Dunai, D; Zoletnik, S; Sárközi, J; Field, A R

    2010-10-01

    An avalanche photodiode based (APD) detector for the visible wavelength range was developed for low light level, high frequency beam emission spectroscopy (BES) experiments in fusion plasmas. This solid state detector has higher quantum efficiency than photomultiplier tubes, and unlike normal photodiodes, it has internal gain. This paper describes the developed detector as well as the noise model of the electronic circuit. By understanding the noise sources and the amplification process, the optimal amplifier and APD reverse voltage setting can be determined, where the signal-to-noise ratio is the highest for a given photon flux. The calculations are compared to the absolute calibration results of the implemented circuit. It was found that for a certain photon flux range, relevant for BES measurements (≈10(8)-10(10) photons/s), the new detector is superior to both photomultipliers and photodiodes, although it does not require cryogenic cooling of any component. The position of this photon flux window sensitively depends on the parameters of the actual experimental implementation (desired bandwidth, detector size, etc.) Several detector units based on these developments have been built and installed in various tokamaks. Some illustrative results are presented from the 8-channel trial BES system installed at Mega-Ampere Spherical Tokamak (MAST) and the 16-channel BES system installed at the Torus Experiment for Technology Oriented Research (TEXTOR).

  15. New gamma detector modules based on micropixel avalanche photodiode

    Science.gov (United States)

    Ahmadov, F.; Ahmadov, G.; Guliyev, E.; Madatov, R.; Sadigov, A.; Sadygov, Z.; Suleymanov, S.; Akberov, R.; Nuriyev, S.; Zerrouk, F.

    2017-01-01

    In this paper presented the results of the ionizing radiation detector modules, which developed on the basis of a new generation of micropixel avalanche photodiode (MAPD) of MAPD-3NK type. The samples were produced in cooperation with the Zecotek Photonics and characterized by the following parameters: sensitive area—3.7 mm × 3.7 mm, density of pixels—10000 pixels/mm2, photon detection efficiency—35-40% (at wavelength of 450-550 nm) and operation voltage—91 V. The beta particle and gamma ray detection performance of MAPD with different single scintillation crystal such as NaI, LFS and p-terphenyl was investigated. The gamma ray detector modules demonstrated a perfect linear behavior of detected signal amplitudes as a function of the gamma ray energy (from 26.3 keV up to 1.33 MeV). Energy resolution for 662 keV gamma rays was 11.2% and the minimum detectable energy was 26.3 keV.

  16. A study of Gd-based parallel plate avalanche counter for thermal neutrons by MC simulation

    Energy Technology Data Exchange (ETDEWEB)

    Rhee, J.T.; Kim, H.G. [IAP, High Energy Physics Lab, Department of Physics, Konkuk University, Seoul 143-701 (Korea, Republic of); Ahmad, Farzana; Jeon, Y.J. [Liquid Crystal Research Center, Department of Chemistry, Konkuk University, Seoul 143-701 (Korea, Republic of); Jamil, M., E-mail: mjamil@konkuk.ac.kr [IAP, High Energy Physics Lab, Department of Physics, Konkuk University, Seoul 143-701 (Korea, Republic of); Division of International Studies, University College, Konkuk University, Seoul 143-701 (Korea, Republic of)

    2013-12-21

    In this work, we demonstrate the feasibility and characteristics of a single-gap parallel plate avalanche counter (PPAC) as a low energy neutron detector, based on Gd-converter coating. Upon falling on the Gd-converter surface, the incident low energy neutrons produce internal conversion electrons which are evaluated and detected. For estimating the performance of the Gd-based PPAC, a simulation study has been performed using GEANT4 Monte Carlo (MC) code. The detector response as a function of incident neutron energies in the range of 25–100 meV has been evaluated with two different physics lists. Using the QGSP{sub B}IC{sub H}P physics list and assuming 5μm converter thickness, 11.8%, 18.48%, and 30.28% detection efficiencies have been achieved for the forward-, the backward-, and the total response of the converter-based PPAC. On the other hand, considering the same converter thickness and detector configuration, with the QGSP{sub B}ERT{sub H}P physics list efficiencies of 12.19%, 18.62%, and 30.81%, respectively, were obtained. These simulation results are briefly discussed.

  17. A study of Gd-based parallel plate avalanche counter for thermal neutrons by MC simulation

    Science.gov (United States)

    Rhee, J. T.; Kim, H. G.; Ahmad, Farzana; Jeon, Y. J.; Jamil, M.

    2013-12-01

    In this work, we demonstrate the feasibility and characteristics of a single-gap parallel plate avalanche counter (PPAC) as a low energy neutron detector, based on Gd-converter coating. Upon falling on the Gd-converter surface, the incident low energy neutrons produce internal conversion electrons which are evaluated and detected. For estimating the performance of the Gd-based PPAC, a simulation study has been performed using GEANT4 Monte Carlo (MC) code. The detector response as a function of incident neutron energies in the range of 25-100 meV has been evaluated with two different physics lists. Using the QGSP_BIC_HP physics list and assuming 5 μm converter thickness, 11.8%, 18.48%, and 30.28% detection efficiencies have been achieved for the forward-, the backward-, and the total response of the converter-based PPAC. On the other hand, considering the same converter thickness and detector configuration, with the QGSP_BERT_HP physics list efficiencies of 12.19%, 18.62%, and 30.81%, respectively, were obtained. These simulation results are briefly discussed.

  18. A theoretical study of improved front-illuminated avalanche drift detectors

    Science.gov (United States)

    Liang, K.; Yuan, J.; Li, H. R.; Yang, R.; Han, D. J.

    2013-06-01

    In this study, two avalanche drift detector (ADD) concepts were theoretically examined. One was an improved detector with an avalanche photodiode (APD) collecting and double pn-junction drift configuration, and the other was a combination of an APD collecting and metal oxide semiconductor (MOS) drift structure. The feasibility of the devices was theoretically investigated by the ISE-TCAD program. ADD can be operated in either Geiger mode or linear mode. In the former case, the detector was found to be appropriate for a single photon avalanche detector with a large collection area. In the latter case, the detector was observed to be well suited to be coupled to a scintillator for gamma-ray detection. The improved ADDs are considered to have good performances in the short wavelength optical detection and in matching common scintillation crystals with more flexibility.

  19. Characterization of avalanche photodiodes for lidar atmospheric return signal detectors

    Science.gov (United States)

    Antill, C. W., Jr.; Holloway, R. M.

    1988-01-01

    Results are presented from tests to characterize noise, dark current, overload, and gain versus bias, relationships of ten avalanche photodiodes. The advantages of avalanche photodiodes over photomultiplier tubes for given laser wavelengths and return signal amplitudes are outlined. The relationship between responsivity and temperature and dark current and temperature are examined. Also, measurements of the noise equivalent power, the excess noise factor, and linearity are given. The advantages of using avalanche photodiodes in the Lidar Atmospheric Sensing Experiment and the Lidar In-Space Technology Experiment are discussed.

  20. Signal-to-noise ratio of Geiger-mode avalanche photodiode single-photon counting detectors

    Science.gov (United States)

    Kolb, Kimberly

    2014-08-01

    Geiger-mode avalanche photodiodes (GM-APDs) use the avalanche mechanism of semiconductors to amplify signals in individual pixels. With proper thresholding, a pixel will be either "on" (avalanching) or "off." This discrete detection scheme eliminates read noise, which makes these devices capable of counting single photons. Using these detectors for imaging applications requires a well-developed and comprehensive expression for the expected signal-to-noise ratio (SNR). This paper derives the expected SNR of a GM-APD detector in gated operation based on gate length, number of samples, signal flux, dark count rate, photon detection efficiency, and afterpulsing probability. To verify the theoretical results, carrier-level Monte Carlo simulation results are compared to the derived equations and found to be in good agreement.

  1. Microchannel Plate Imaging Detectors for the Ultraviolet

    Science.gov (United States)

    Siegmund, O. H. W.; Gummin, M. A.; Stock, J.; Marsh, D.

    1992-01-01

    There has been significant progress over the last few years in the development of technologies for microchannel plate imaging detectors in the Ultraviolet (UV). Areas where significant developments have occurred include enhancements of quantum detection efficiency through improved photocathodes, advances in microchannel plate performance characteristics, and development of high performance image readout techniques. The current developments in these areas are summarized, with their applications in astrophysical instrumentation.

  2. Development of a 13-in. Hybrid Avalanche Photo-Detector (HAPD) for a next generation water Cherenkov detector

    Energy Technology Data Exchange (ETDEWEB)

    Nakayama, H. [Department of Physics, University of Tokyo, 7-3-1 Hongo, Bunkyo-ku, Tokyo 113-0033 (Japan)]. E-mail: nakkan@hep.phys.s.u-tokyo.ac.jp; Kusaka, A. [Department of Physics, University of Tokyo, 7-3-1 Hongo, Bunkyo-ku, Tokyo 113-0033 (Japan); Kakuno, H. [Department of Physics, University of Tokyo, 7-3-1 Hongo, Bunkyo-ku, Tokyo 113-0033 (Japan); Abe, T. [Department of Physics, University of Tokyo, 7-3-1 Hongo, Bunkyo-ku, Tokyo 113-0033 (Japan); Iwasaki, M. [Department of Physics, University of Tokyo, 7-3-1 Hongo, Bunkyo-ku, Tokyo 113-0033 (Japan); Aihara, H. [Department of Physics, University of Tokyo, 7-3-1 Hongo, Bunkyo-ku, Tokyo 113-0033 (Japan); Shiozawa, M. [Institute for Cosmic Ray Research, University of Tokyo, Higashi-Mozumi, Kamioka-cho, Hida city, Gifu 506-1205 (Japan); Tanaka, M. [Institute for Particle and Nuclear Studies, High Energy Research Organization (KEK), 1-1 Oho, Tsukuba, Ibaraki 305-0801 (Japan); Kyushima, H. [Electron Tube Division, Hamamatsu Photonics K.K., 314-5 Simokanzo, Iwata City 438-0193, Shizuoka (Japan); Suyama, M. [Electron Tube Division, Hamamatsu Photonics K.K., 314-5 Simokanzo, Iwata City 438-0193, Shizuoka (Japan); Kawai, Y. [Electron Tube Division, Hamamatsu Photonics K.K., 314-5 Simokanzo, Iwata City 438-0193, Shizuoka (Japan)

    2006-11-01

    We have developed a 13-in. Hybrid Avalanche Photo-Detector (HAPD) for photosensors in next generation water Cherenkov type detectors. We study the performance of the HAPD and the results show good time resolution better than {sigma}=1ns, good sensitivity for single photon detection, wide dynamic range, and good uniformity on the photocathode. The HAPD is also expected to be less expensive than large PMTs because of its simpler structure without dynodes.

  3. Low noise pixel detectors based on gated geiger mode avalanche photodiodes

    OpenAIRE

    Vilella Figueras, Eva; Comerma Montells, Albert; Alonso Casanovas, Oscar; Diéguez Barrientos, Àngel

    2011-01-01

    The gated operation is proposed as an effective method to reduce the noise in pixel detectors based on Geiger mode avalanche photodiodes. A prototype with the sensor and the front-end electronics monolithically integrated has been fabricated with a conventional HV-CMOS process. Experimental results demonstrate the increase of the dynamic range of the sensor by applying this technique.

  4. Design and TCAD simulation of double-sided pixelated low gain avalanche detectors

    Energy Technology Data Exchange (ETDEWEB)

    Dalla Betta, Gian-Franco, E-mail: gianfranco.dallabetta@unitn.it [Dipartimento di Ingegneria Industriale, Università di Trento, Via Sommarive 9, 38123 Trento (Italy); TIFPA INFN, Via Sommarive 14, 38123 Trento (Italy); Pancheri, Lucio [Dipartimento di Ingegneria Industriale, Università di Trento, Via Sommarive 9, 38123 Trento (Italy); TIFPA INFN, Via Sommarive 14, 38123 Trento (Italy); Boscardin, Maurizio [Fondazione Bruno Kessler, Via Sommarive 18, 38123 Trento (Italy); TIFPA INFN, Via Sommarive 14, 38123 Trento (Italy); Paternoster, Giovanni [Fondazione Bruno Kessler, Via Sommarive 18, 38123 Trento (Italy); Piemonte, Claudio [Fondazione Bruno Kessler, Via Sommarive 18, 38123 Trento (Italy); TIFPA INFN, Via Sommarive 14, 38123 Trento (Italy); Cartiglia, Nicolo; Cenna, Francesca [INFN Sezione di Torino, Via P. Giuria 2, 10125 Torino (Italy); Bruzzi, Mara [Dipartimento di FIsica e Astronomia, Università di Firenze, and INFN Sezione di Firenze, Via Giovanni Sansone 1, 50019 Sesto Fiorentino (Italy)

    2015-10-01

    We introduce a double-sided variant of low gain avalanche detector, suitable for pixel arrays without dead-area in between the different read-out elements. TCAD simulations were used to validate the device concept and predict its performance. Different design options and selected simulation results are presented, along with the proposed fabrication process.

  5. An indirect flat-panel detector with avalanche gain for low dose x-ray imaging: SAPHIRE (scintillator avalanche photoconductor with high resolution emitter readout)

    Science.gov (United States)

    Zhao, Wei; Li, Dan; Rowlands, J. A.; Egami, N.; Takiguchi, Y.; Nanba, M.; Honda, Y.; Ohkawa, Y.; Kubota, M.; Tanioka, K.; Suzuki, K.; Kawai, T.

    2008-03-01

    An indirect flat-imager with programmable avalanche gain and field emitter array (FEA) readout is being investigated for low-dose x-ray imaging with high resolution. It is made by optically coupling a structured x-ray scintillator CsI (Tl) to an amorphous selenium (a-Se) avalanche photoconductor called HARP (high-gain avalanche rushing photoconductor). The charge image created by HARP is read out by electron beams generated by the FEA. The proposed detector is called SAPHIRE (Scintillator Avalanche Photoconductor with HIgh Resolution Emitter readout). The avalanche gain of HARP depends on both a-Se thickness and applied electric field E Se. At E Se of > 80 V/μm, the avalanche gain can enhance the signal at low dose (e.g. fluoroscopy) and make the detector x-ray quantum noise limited down to a single x-ray photon. At high exposure (e.g. radiography), the avalanche gain can be turned off by decreasing E Se to < 70 V/μm. In this paper the imaging characteristics of the FEA readout method, including the spatial resolution and noise, were investigated experimentally using a prototype optical HARP-FEA image sensor. The potential x-ray imaging performance of SAPHIRE, especially the aspect of programmable gain to ensure wide dynamic range and x-ray quantum noise limited performance at the lowest exposure in fluoroscopy, was investigated.

  6. Direct observation of avalanche scintillations in a THGEM-based two-phase Ar avalanche detector using Geiger-mode APD

    CERN Document Server

    Bondar, A; Grebenuk, A; Sokolov, A; Akimov, D; Alexandrov, I; Breskin, A

    2010-01-01

    A novel concept of optical signal recording in two-phase avalanche detectors, with Geiger-mode Avalanche Photodiodes (G-APD) is described. Avalanche-scintillation photons were measured in a thick Gas Electron Multiplier (THGEM) in view of potential applications in rare-event experiments. The effective detection of avalanche scintillations in THGEM holes has been demonstrated in two-phase Ar with a bare G-APD without wavelength shifter, i.e. insensitive to VUV emission of Ar. At gas-avalanche gain of 400 and under \\pm 70^\\circ viewing-angle, the G-APD yielded 640 photoelectrons (pe) per 60 keV X-ray converted in liquid Ar; this corresponds to 0.7 pe per initial (prior to multiplication) electron. The avalanche-scintillation light yield measured by the G-APD was about 0.7 pe per avalanche electron, extrapolated to 4pi acceptance. The avalanche scintillations observed occurred presumably in the near infrared (NIR) where G-APDs may have high sensitivity. The measured scintillation yield is similar to that observe...

  7. R and D status of a large-aperture hybrid avalanche photo-detector

    Energy Technology Data Exchange (ETDEWEB)

    Abe, Toshinori, E-mail: toshi@hep.phys.s.u-tokyo.ac.j [University of Tokyo, 7-3-1 Hongo, Bunkyo-ku, Tokyo 113-0033 (Japan); Aihara, Hiroaki; Iwasaki, Masako; Fujimori, Hiroki; Kasimura, Keizo; Mineo, Sogo; Uchida, Tomohisa [University of Tokyo, 7-3-1 Hongo, Bunkyo-ku, Tokyo 113-0033 (Japan); Tanaka, Manobu [Institute for Particle and Nuclear Studies, High Energy Accelerator Research Organization, 1-1 Oho, Tsukuba, Ibaraki 305-0801 (Japan); Kawai, Yoshihiko; Kyushima, Hiroyuki; Suyama, Motohiro [Electron Tube Division, Hamamatsu Photonics K.K., 314-5 Shimokanzo, Iwata City, Shizuoka 438-0193 (Japan); Shiozawa, Masato [Kamioka Observatory, Institute for Cosmic Ray Research ICRR, University of Tokyo, Higashi-Mozumi, Kamioka-cho, Hida City, Gifu 506-1205 (Japan)

    2010-11-01

    This paper reports on the R and D status of a large-aperture Hybrid Avalanche Photo-Detector (HAPD). We have developed a 13-inch aperture HAPD and its readout system. The HAPD is a photo-detector expected to replace the photomultiplier tube (PMT) in next-generation imaging water Cherenkov detectors such as Hyper Kamiokande. We will present the recent progress made in readout system development. The readout system involves a fast sampling device. The sampling depth (number of cells) has been extended to 256 from 64 in order to measure longer waveform length. The variation in AC gain is now fixed and the input analog bandwidth improved.

  8. HgCdTe Infrared Avalanche Photodiode Single Photon Detector Arrays for the LIST and Other Decadal Missions Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Develop a HgCdTe avalanche photodiode (APD)  SWIR/IR linear mode photon counting (LMPC) array detector system in support of the LIST lidar. Provide a new type...

  9. Modeling of high-precision wavefront sensing with new generation of CMT avalanche photodiode infrared detectors.

    Science.gov (United States)

    Gousset, Silvère; Petit, Cyril; Michau, Vincent; Fusco, Thierry; Robert, Clelia

    2015-12-01

    Near-infrared wavefront sensing allows for the enhancement of sky coverage with adaptive optics. The recently developed HgCdTe avalanche photodiode arrays are promising due to their very low detector noise, but still present an imperfect cosmetic that may directly impact real-time wavefront measurements for adaptive optics and thus degrade performance in astronomical applications. We propose here a model of a Shack-Hartmann wavefront measurement in the presence of residual fixed pattern noise and defective pixels. To adjust our models, a fine characterization of such an HgCdTe array, the RAPID sensor, is proposed. The impact of the cosmetic defects on the Shack-Hartmann measurement is assessed through numerical simulations. This study provides both a new insight on the applicability of cadmium mercury telluride (CMT) avalanche photodiodes detectors for astronomical applications and criteria to specify the cosmetic qualities of future arrays.

  10. A novel technique for the measurement of the avalanche fluctuation of gaseous detectors

    CERN Document Server

    Kobayashi, Makoto; Kawaguchi, Tomohiko; Fujii, Keisuke; Fusayasu, Takahiro; Ikematsu, Katsumasa; Kato, Yukihiro; Kawada, Shin-ichi; Matsuda, Takeshi; Settles, Ronald Dean; Sugiyama, Akira; Takahashi, Tohru; Tian, Junping; Watanabe, Takashi; Yonamine, Ryo

    2016-01-01

    We have developed a novel technique for the measurement of the avalanche fluctuation of gaseous detectors using a UV laser. The technique is simple and requires a short data-taking time of about ten minutes. Furthermore, it is applicable for relatively low gas gains. Our experimental setup as well as the measurement principle, and the results obtained with a stack of Gas Electron Multipliers (GEMs) operated in several gas mixtures are presented.

  11. A novel technique for the measurement of the avalanche fluctuation of gaseous detectors

    Science.gov (United States)

    Kobayashi, M.; Ogawa, T.; Kawaguchi, T.; Fujii, K.; Fusayasu, T.; Ikematsu, K.; Kato, Y.; Kawada, S.; Matsuda, T.; Settles, R. D.; Sugiyama, A.; Takahashi, T.; Tian, J.; Watanabe, T.; Yonamine, R.

    2017-02-01

    We have developed a novel technique for the measurement of the avalanche fluctuation of gaseous detectors using a UV laser. The technique is simple and requires a short data-taking time of about ten minutes. Furthermore, it is applicable for relatively low gas gains. Our experimental setup as well as the measurement principle, and the results obtained with a stack of Gas Electron Multipliers (GEMs) operated in several gas mixtures are presented.

  12. Two-phase Cryogenic Avalanche Detector with electroluminescence gap operated in argon doped with nitrogen

    CERN Document Server

    Bondar, A; Dolgov, A; Nosov, V; Shekhtman, L; Shemyakina, E; Sokolov, A

    2016-01-01

    A two-phase Cryogenic Avalanche Detector (CRAD) with electroluminescence (EL) gap, operated in argon doped with a minor (49$\\pm$7 ppm) admixture of nitrogen, has been studied. The EL gap was optically read out using cryogenic PMTs located on the perimeter of the gap. We present the results of the measurements of the N$_2$ content, detector sensitivity to X-ray-induced signals, EL gap yield and electron lifetime in the liquid. The detector sensitivity, at a drift field in liquid Ar of 0.6 kV/cm, was measured to be 9 and 16 photoelectrons recorded at the PMTs per keV of deposited energy at 23 and 88 keV respectively. Such two-phase detectors, with enhanced sensitivity to the S2 (ionization-induced) signal, are relevant in the field of argon detectors for dark matter search and low energy neutrino detection.

  13. Two-phase Cryogenic Avalanche Detector with electroluminescence gap operated in argon doped with nitrogen

    Science.gov (United States)

    Bondar, A.; Buzulutskov, A.; Dolgov, A.; Nosov, V.; Shekhtman, L.; Shemyakina, E.; Sokolov, A.

    2017-02-01

    A two-phase Cryogenic Avalanche Detector (CRAD) with electroluminescence (EL) gap, operated in argon doped with a minor (49±7 ppm) admixture of nitrogen, has been studied. The EL gap was optically read out using cryogenic PMTs located on the perimeter of the gap. We present the results of the measurements of the N2 content, detector sensitivity to X-ray-induced signals, EL gap yield and electron lifetime in the liquid. The detector sensitivity, at a drift field in liquid Ar of 0.6 kV/cm, was measured to be 9 and 16 photoelectrons recorded at the PMTs per keV of deposited energy at 23 and 88 keV respectively. Such two-phase detectors, with enhanced sensitivity to the S2 (ionization-induced) signal, are relevant in the field of argon detectors for dark matter search and low energy neutrino detection.

  14. Quick single-photon detector with many avalanche photo diodes working on the time division

    Institute of Scientific and Technical Information of China (English)

    Jian Peng; Yifei Fu; Li Yao; Xudong Shang; Zhixin Lu; Bojun Yang; Li Yu

    2008-01-01

    Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.

  15. In-beam evaluation of a medium-size Resistive-Plate WELL gaseous particle detector

    Science.gov (United States)

    Moleri, L.; Amaro, F. D.; Arazi, L.; Azevedo, C. D. R.; Breskin, A.; Coimbra, A. E. C.; Oliveri, E.; Pereira, F. A.; Shaked Renous, D.; Schaarschmidt, J.; dos Santos, J. M. F.; Veloso, J. F. C. A.; Bressler, S.

    2016-09-01

    In-beam evaluation of a fully-equipped medium-size 30 × 30 cm2 Resistive Plate WELL (RPWELL) detector is presented. It consists here of a single element gas-avalanche multiplier with Semitron ESD225 resistive plate, 1 cm2 readout pads and APV25/SRS electronics. Similarly to previous results with small detector prototypes, stable operation at high detection efficiency (> 98%) and low average pad multiplicity (~ 1.2) were recorded with 150 GeV muon and high-rate pion beams, in Ne/(5%CH4), Ar/(5%CH4) and Ar/(7%CO2). This is an important step towards the realization of robust detectors suitable for applications requiring large-area coverage; among them Digital Hadron Calorimetry.

  16. In-beam evaluation of a medium-size Resistive-Plate WELL gaseous particle detector

    CERN Document Server

    Moleri, L

    2016-01-01

    In-beam evaluation of a fully-equipped medium-size 30$\\times$30 cm$^2$ Resistive Plate WELL (RPWELL) detector is presented. It consists here of a single element gas-avalanche multiplier with Semitron ESD225 resistive plate, 1 cm$^2$ readout pads and APV25/SRS electronics. Similarly to previous results with small detector prototypes, stable operation at high detection efficiency (>98%) and low average pad multiplicity (~1.2) were recorded with 150 GeV muon and high-rate pion beams, in Ne/(5%CH$_4$), Ar/(5%CH$_4$) and Ar/(7%CO$_2$). This is an important step towards the realization of robust detectors suitable for applications requiring large-area coverage; among them Digital Hadron Calorimetry.

  17. Ultra-low noise single-photon detector based on Si avalanche photodiode.

    Science.gov (United States)

    Kim, Yong-Su; Jeong, Youn-Chang; Sauge, Sebastien; Makarov, Vadim; Kim, Yoon-Ho

    2011-09-01

    We report operation and characterization of a lab-assembled single-photon detector based on commercial silicon avalanche photodiodes (PerkinElmer C30902SH, C30921SH). Dark count rate as low as 5 Hz was achieved by cooling the photodiodes down to -80 °C. While afterpulsing increased as the photodiode temperature was decreased, total afterpulse probability did not become significant due to detector's relatively long deadtime in a passively-quenched scheme. We measured photon detection efficiency >50% at 806 nm. © 2011 American Institute of Physics

  18. High rate resistive plate chamber for LHC detector upgrades

    Energy Technology Data Exchange (ETDEWEB)

    Haddad, Y., E-mail: haddad@llr.in2p3.fr [Laboratoire Leprince-Ringuet (LLR), École Polytechnique, 91120 Palaiseau (France); Laktineh, I.; Grenier, G.; Lumb, N. [IPNL, Villeurbanne 69622 Lyon (France); Cauwenbergh, S. [Ghent University, Ghent (Belgium)

    2013-08-01

    The limitation of the detection rate of standard bakelite resistive plate chambers (RPCs) used as muon detectors in the LHC experiments has prevented the use of such detectors in the high rate regions in both CMS and ATLAS detectors. One alternative to these detectors is RPCs made with low resistivity glass plates (10{sup 10}Ωcm), a beam test at DESY has shown that such detectors can operate at few thousand Hz/cm{sup 2} with high efficiency (>90%)

  19. Single-Photon-Sensitive HgCdTe Avalanche Photodiode Detector

    Science.gov (United States)

    Huntington, Andrew

    2013-01-01

    The purpose of this program was to develop single-photon-sensitive short-wavelength infrared (SWIR) and mid-wavelength infrared (MWIR) avalanche photodiode (APD) receivers based on linear-mode HgCdTe APDs, for application by NASA in light detection and ranging (lidar) sensors. Linear-mode photon-counting APDs are desired for lidar because they have a shorter pixel dead time than Geiger APDs, and can detect sequential pulse returns from multiple objects that are closely spaced in range. Linear-mode APDs can also measure photon number, which Geiger APDs cannot, adding an extra dimension to lidar scene data for multi-photon returns. High-gain APDs with low multiplication noise are required for efficient linear-mode detection of single photons because of APD gain statistics -- a low-excess-noise APD will generate detectible current pulses from single photon input at a much higher rate of occurrence than will a noisy APD operated at the same average gain. MWIR and LWIR electron-avalanche HgCdTe APDs have been shown to operate in linear mode at high average avalanche gain (M > 1000) without excess multiplication noise (F = 1), and are therefore very good candidates for linear-mode photon counting. However, detectors fashioned from these narrow-bandgap alloys require aggressive cooling to control thermal dark current. Wider-bandgap SWIR HgCdTe APDs were investigated in this program as a strategy to reduce detector cooling requirements.

  20. Single photon avalanche detectors: prospects of new quenching and gain mechanisms

    Directory of Open Access Journals (Sweden)

    Hall David

    2015-11-01

    Full Text Available While silicon single-photon avalanche diodes (SPAD have reached very high detection efficiency and timing resolution, their use in fibre-optic communications, optical free space communications, and infrared sensing and imaging remains limited. III-V compounds including InGaAs and InP are the prevalent materials for 1550 nm light detection. However, even the most sensitive 1550 nm photoreceivers in optical communication have a sensitivity limit of a few hundred photons. Today, the only viable approach to achieve single-photon sensitivity at 1550 nm wavelength from semiconductor devices is to operate the avalanche detectors in Geiger mode, essentially trading dynamic range and speed for sensitivity. As material properties limit the performance of Ge and III-V detectors, new conceptual insight with regard to novel quenching and gain mechanisms could potentially address the performance limitations of III-V SPADs. Novel designs that utilise internal self-quenching and negative feedback can be used to harness the sensitivity of single-photon detectors,while drastically reducing the device complexity and increasing the level of integration. Incorporation of multiple gain mechanisms, together with self-quenching and built-in negative feedback, into a single device also hold promise for a new type of detector with single-photon sensitivity and large dynamic range.

  1. Design and fabrication of an optimum peripheral region for low gain avalanche detectors

    Energy Technology Data Exchange (ETDEWEB)

    Fernández-Martínez, Pablo; Flores, D., E-mail: david.flores@imb-cnm.csic.es; Hidalgo, S.; Greco, V.; Merlos, A.; Pellegrini, G.; Quirion, D.

    2016-06-11

    Low Gain Avalanche Detectors (LGAD) represent a remarkable advance in high energy particle detection, since they provide a moderate increase (gain ~10) of the collected charge, thus leading to a notable improvement of the signal-to-noise ratio, which largely extends the possible application of Silicon detectors beyond their present working field. The optimum detection performance requires a careful implementation of the multiplication junction, in order to obtain the desired gain on the read out signal, but also a proper design of the edge termination and the peripheral region, which prevents the LGAD detectors from premature breakdown and large leakage current. This work deals with the critical technological aspects required to optimize the LGAD structure. The impact of several design strategies for the device periphery is evaluated with the aid of TCAD simulations, and compared with the experimental results obtained from the first LGAD prototypes fabricated at the IMB-CNM clean room. Solutions for the peripheral region improvement are also provided.

  2. Design and Fabrication of an Optimum Peripheral Region for Low Gain Avalanche Detectors

    CERN Document Server

    Fernandez-Martinez, Pablo; Hidalgo, Salvador; Greco, Virginia; Merlos, Angel; Pellegrini, Giulio; Quirion, David

    2015-01-01

    Low Gain Avalanche Detectors (LGAD) represent a remarkable advance in high energy particle detection, since they provide a moderate increase (gain ~10) of the collected charge, thus leading to a notable improvement of the signal-to-noise ratio, which largely extends the possible application of Silicon detectors beyond their present working field. The optimum detection performance requires a careful implementation of the multiplication junction, in order to obtain the desired gain on the read out signal, but also a proper design of the edge termination and the peripheral region, which prevents the LGAD detectors from premature breakdown and large leakage current. This work deals with the critical technological aspects when optimising the LGAD structure. The impact of several design strategies for the device periphery is evaluated with the aid of TCAD simulations, and compared with the experimental results obtained from the first LGAD prototypes fabricated at the IMB-CNM clean room. Solutions for the peripheral...

  3. Aging study for resistive plate chambers of the CMS muon trigger detector

    CERN Document Server

    Abbrescia, M; Iaselli, G; Loddo, F; Maggi, M; Marangelli, B; Natali, S; Nuzzo, S; Pugliese, G; Ranieri, A; Romano, F; Altieri, S; Belli, G; Bruno, G; Guida, R; Ratti, S P; Riccardi, C; Torre, P; Vitulo, P

    2003-01-01

    A long-term aging test of a Resistive Plate Chamber (RPC) was carried out with an intense gamma **1**3**7Cs source. The detector was operated in avalanche mode and had the bakelite surface treated with linseed oil. After the irradiation the estimated dose, charge and fluence were approximately equal to the expected values after 10 years of operation in the CMS barrel region. During and after the irradiation, the RPC performance was monitored with cosmic muons and showed no relevant aging effects. Moreover, no variation of the bakelite resistance was observed.

  4. Thick GEM versus thin GEM in two-phase argon avalanche detectors

    CERN Document Server

    Bondar, A; Grebenuk, A; Pavlyuchenko, D; Tikhonov, Y; Breskin, Amos

    2008-01-01

    The performance of thick GEMs (THGEMs) was compared to that of thin GEMs in two-phase Ar avalanche detectors, in view of their potential application in coherent neutrino-nucleus scattering, dark-matter search and in other rare-event experiments. The detectors comprised a 1 cm thick liquid-Ar layer followed by either a double-THGEM or a triple-GEM multiplier, operated in the saturated vapor above the liquid phase. Three types of THGEMs were studied: those made of G10 and Kevlar and that with resistive electrodes (RETHGEM). Only the G10-made THGEM showed a stable performance in two-phase Ar with gains reaching 3000. Successful operation of two-phase Ar avalanche detectors with either thin- or thick-GEM multipliers was demonstrated at low detection thresholds, of 4 and 20 primary electrons respectively. Compared to the triple-GEM the double-THGEM multiplier yielded slower anode signals; this allowed applying a pulse-shape analysis to effectively reject noise signals. Noise rates of both multipliers were evaluate...

  5. A new type of detector time of flight - multi-gap resistive plate chamber

    CERN Document Server

    Chen, H; Eppley, G; Geurts, F J M; Huang, S; Li, C; Liu, H; Llope, W J; Ruan, L; Shao, M; Wang, X L; Wang, Z; Wu, J; Xu, Z; Zhang, Z

    2004-01-01

    Multi-gap resistive plate chamber is a new detector technology. It was first developed by the LHC-ALICE group at CERN in the late 1990s. The MRPC is a ideal detector for time-of-flight measurement due to its small gaps and works in the proportional (avalanche) mode. The beam test of single module result shows that MRPC tuning resolution is better than 70ps and the detection efficiency is higher than 95%. It is also radiation hard. A time-of-flight tray with 28 on MRPC modules. was tested at AGS. The average timing resolution is about 75ps (including the 4cm of beam spread) and detection efficiency is better than 95%. This tray has been installed on STAR detector system in October 2002 and used on the 200GeV d+Au experiment.

  6. A cooled avalanche photodiode detector for X-ray magnetic diffraction experiments

    CERN Document Server

    Kishimoto, S; Ito, M

    2001-01-01

    A cooled avalanche photodiode (APD) detector was developed for X-ray magnetic diffraction experiments. A stack of four silicon APDs was cooled down to 243 K by a thermoelectric cooler. The energy widths of 0.89 and 1.55 keV (FWHM) were obtained for 8.05 keV X-rays at 1x10 sup 6 s sup - sup 1 and for 16.53 keV X-rays at 2x10 sup 6 s sup - sup 1 , respectively. Test measurements of X-ray magnetic diffraction were executed using a terbium single crystal and white synchrotron radiation. A peak width of (1 0 3) reflection (5.4 keV) was roughly three times wider than that with a high-purity germanium detector.

  7. SWAD: inherent photon counting performance of amorphous selenium multi-well avalanche detector

    Science.gov (United States)

    Stavro, Jann; Goldan, Amir H.; Zhao, Wei

    2016-03-01

    Photon counting detectors (PCDs) have the potential to improve x-ray imaging, however they are still hindered by several performance limitations and high production cost. By using amorphous Selenium (a-Se) the cost of PCDs can be significantly reduced compared to crystalline materials and enable large area detector fabrication. To overcome the problem of low carrier mobility and low charge conversion gain in a-Se, we are developing a novel direct conversion a- Se field-Shaping multi-Well Avalanche Detector (SWAD). SWAD circumvents the charge transport limitation by using a Frisch grid built within the readout circuit, reducing charge collection time to ~200 ns. Field shaping permits depth independent avalanche gain in wells, resulting in total conversion gain that is comparable to Si and CdTe. In the present work we investigate the effects of charge sharing and energy loss to understand the inherent photon counting performance for SWAD at x-ray energies used in breast imaging applications (20-50keV). The energy deposition profile for each interacting x-ray was determined with Monte Carlo simulation. For the energy ranges we are interested in, photoelectric interaction dominates, with a k-fluorescence yield of approximately 60%. Using a monoenergetic 45 keV beam incident on a target pixel in 400um of a-Se, our results show that only 20.42 % and 22.4 % of primary interacting photons have kfluorescence emissions which escape the target pixel for 100um and 85um pixel sizes respectively, demonstrating SWAD's potential for high spatial resolution applications.

  8. MPPC versus MRS APD in two-phase Cryogenic Avalanche Detectors

    CERN Document Server

    Bondar, A; Dolgov, A; Shemyakina, E; Sokolov, A

    2015-01-01

    Two-phase Cryogenic Avalanche Detectors (CRADs) with combined THGEM/GAPD multiplier have become an emerging potential technique for dark matter search and coherent neutrino-nucleus scattering experiments. In such a multiplier the THGEM hole avalanches are optically recorded in the Near Infrared (NIR) using a matrix of Geiger-mode APDs (GAPDs). To select the proper sensor, the performances of six GAPD types manufactured by different companies, namely by Hamamatsu (MPPCs), CPTA (MRS APDs) and SensL (SiPMs), have been comparatively studied at cryogenic temperatures when operated in two-phase CRADs in Ar at 87 K. While the GAPDs with ceramic packages failed to operate properly at cryogenic temperatures, those with plastic packages, namely MPPC S10931-100P and MRS APD 149-35, showed satisfactory performances at 87 K. In addition, MPPC S10931-100P turned out to be superior in terms of the higher detection efficiency, lower nose rate, lower pixel quenching resistor and better characteristics reproducibility.

  9. SAPHIRE: A New Flat-Panel Digital Mammography Detector With Avalanche Photoconductor and High-Resolution Field Emitter Readout

    Science.gov (United States)

    2006-06-01

    AD_________________ Award Number: W81XWH-04-1-0554 TITLE: SAPHIRE : A New Flat-Panel Digital... SAPHIRE : A New Flat-Panel Digital Mammography Detector with Avalanche Photoconductor and High-Resolution Field Emitter Readout 5b. GRANT NUMBER w81xwh-04...CsI), and form a charge image that is read out by a high-resolution field emitter array (FEA). We call the proposed detector SAPHIRE (Scintillator

  10. Random Number Hardware Generator Using Geiger-Mode Avalanche Photo Detector

    CERN Document Server

    Beznosko, D; Duspayev, A; Tailakov, A; Yessenov, M

    2015-01-01

    This paper presents the physical concept and test results of sample data of the high-speed hardware true random number generator design based on typically used for High Energy Physics hardware. Main features of this concept are the high speed of the true random numbers generation (tens of Mbt/s), miniature size and estimated lower production cost. This allows the use of such a device not only in large companies and government offices but for the end-user data cryptography, in classrooms, in scientific Monte-Carlo simulations, computer games and any other place where large number of true random numbers is required. The physics of the operations principle of using a Geiger-mode avalanche photo detector is discussed and the high quality of the data collected is demonstrated.

  11. Measurement-based characterization of multipixel avalanche photodiodes for scintillating detectors

    CERN Document Server

    Dziewiecki, M

    2012-01-01

    Multipixel avalanche photodiodes (MAPD) are recently gaining popularity in high energy physics experiments as an attractive replacement for photomultiplier tubes, which have been extensively used for many years as a part of various scintillating detectors. Their low price, small dimensions and another features facilitating their use (like mechanical shock resistance, magnetic field immunity or moderate supply voltage) make the MAPDs a good choice for commercial use as well, what is reflected in growing number of producers as well as MAPD models available on the market. This dissertation presents Author’s experience with MAPD measurements and modelling, gained during his work on the T2K (Tokai-to-Kamioka) long-baseline neutrino experiment, carried out by an international collaboration in Japan. First, operation principle of the MAPD, definitions of various parameters and measurement methods are discussed. Then, a device for large-scale MAPD measurements and related data processing methods are described. Fina...

  12. HgCdTe Avalanche Photodiode Detectors for Airborne and Spaceborne Lidar at Infrared Wavelengths

    Science.gov (United States)

    Sun, Xiaoli; Abshire, James B.; Beck, Jeffrey D.; Mitra, Pradip; Reiff, Kirk; Yang, Guangning

    2017-01-01

    We report results from characterizing the HgCdTe avalanche photodiode (APD) sensorchip assemblies (SCA) developed for lidar at infrared wavelength using the high density vertically integrated photodiodes (HDVIP) technique. These devices demonstrated high quantum efficiency, typically greater than 90 between 0.8 micrometers and the cut-off wavelength, greater than 600 APD gain, near unity excess noise factor, 6-10 MHz electrical bandwidth and less than 0.5 fW/Hz(exp.1/2) noise equivalent power (NEP). The detectors provide linear analog output with a dynamic range of 2-3 orders of magnitude at a fixed APD gain without averaging, and over 5 orders of magnitude by adjusting the APD and preamplifier gain settings. They have been successfully used in airborne CO2 and CH4 integrated path differential absorption (IPDA) lidar as a precursor for space lidar applications.

  13. Negative feedback avalanche diode

    Science.gov (United States)

    Itzler, Mark Allen (Inventor)

    2010-01-01

    A single-photon avalanche detector is disclosed that is operable at wavelengths greater than 1000 nm and at operating speeds greater than 10 MHz. The single-photon avalanche detector comprises a thin-film resistor and avalanche photodiode that are monolithically integrated such that little or no additional capacitance is associated with the addition of the resistor.

  14. Investigation of a clinical PET detector module design that employs large-area avalanche photodetectors.

    Science.gov (United States)

    Peng, Hao; Olcott, Peter D; Spanoudaki, Virginia; Levin, Craig S

    2011-06-21

    We investigated the feasibility of designing an Anger-logic PET detector module using large-area high-gain avalanche photodiodes (APDs) for a brain-dedicated PET/MRI system. Using Monte Carlo simulations, we systematically optimized the detector design with regard to the scintillation crystal, optical diffuser, surface treatment, layout of large-area APDs, and signal-to-noise ratio (SNR, defined as the 511 keV photopeak position divided by the standard deviation of noise floor in an energy spectrum) of the APD devices. A detector prototype was built comprising an 8 × 8 array of 2.75 × 3.00 × 20.0 mm3 LYSO (lutetium-yttrium-oxyorthosilicate) crystals and a 22.0 × 24.0 × 9.0 mm3 optical diffuser. From the four designs of the optical diffuser tested, two designs employing a slotted diffuser are able to resolve all 64 crystals within the block with good uniformity and peak-to-valley ratio. Good agreement was found between the simulation and experimental results. For the detector employing a slotted optical diffuser, the energy resolution of the global energy spectrum after normalization is 13.4 ± 0.4%. The energy resolution of individual crystals varies between 11.3 ± 0.3% and 17.3 ± 0.4%. The time resolution varies between 4.85 ± 0.04 (center crystal), 5.17 ± 0.06 (edge crystal), and 5.18 ± 0.07 ns (corner crystal). The generalized framework proposed in this work helps to guide the design of detector modules for selected PET system configurations, including scaling the design down to a preclinical PET system, scaling up to a whole-body clinical scanner, as well as replacing APDs with other novel photodetectors that have higher gain or SNR such as silicon photomultipliers.

  15. Spectral method for characterization of avalanche photodiode working as single-photon detector.

    Science.gov (United States)

    Cavalcanti, Maria Daniela Santabaia; Mendonça, Fábio Alencar; Ramos, Rubens Viana

    2011-09-01

    In this Letter, a new method for avalanche photodiode characterization, based on the spectral analysis of the photocurrent produced during an avalanche, is proposed. The theory is developed, and an experimental characterization of an avalanche photodiode working in the Geiger mode with CW laser is performed.

  16. First demonstration of THGEM/GAPD-matrix optical readout in two-phase Cryogenic Avalanche Detector in Ar

    CERN Document Server

    Bondar, A; Dolgov, A; Grebenuk, A; Shemyakina, E; Sokolov, A; Breskin, A; Thers, D

    2013-01-01

    The multi-channel optical readout of a THGEM multiplier coupled to a matrix of 3x3 Geiger-mode APDs (GAPDs) was demonstrated in a two-phase Cryogenic Avalanche Detector (CRAD) in Ar. The GAPDs recorded THGEM-hole avalanches in the Near Infrared (NIR). At an avalanche charge gain of 160, the yield of the combined THGEM/GAPD-matrix multiplier amounted at ~80 photoelectrons per 20 keV X-ray absorbed in the liquid phase. A spatial resolution of 2.5 mm (FWHM) has been measured for the impinging X-rays. This technique has potential applications in coherent neutrino-nucleus scattering and dark matter search experiments.

  17. First demonstration of THGEM/GAPD-matrix optical readout in a two-phase Cryogenic Avalanche Detector in Ar

    Energy Technology Data Exchange (ETDEWEB)

    Bondar, A. [Budker Institute of Nuclear Physics, 630090 Novosibirsk (Russian Federation); Novosibirsk State University, Pirogov Street 2, 630090 Novosibirsk (Russian Federation); Buzulutskov, A., E-mail: a.f.buzulutskov@inp.nsk.su [Budker Institute of Nuclear Physics, 630090 Novosibirsk (Russian Federation); Novosibirsk State University, Pirogov Street 2, 630090 Novosibirsk (Russian Federation); Dolgov, A. [Novosibirsk State University, Pirogov Street 2, 630090 Novosibirsk (Russian Federation); Grebenuk, A. [Budker Institute of Nuclear Physics, 630090 Novosibirsk (Russian Federation); Shemyakina, E.; Sokolov, A. [Budker Institute of Nuclear Physics, 630090 Novosibirsk (Russian Federation); Novosibirsk State University, Pirogov Street 2, 630090 Novosibirsk (Russian Federation); Breskin, A. [Weizmann Institute of Science, 76100 Rehovot (Israel); Thers, D. [SUBATECH, Ecole des Mines de Nantes, CNRS/In2p3, Université de Nantes, 44307 Nantes Cedex 3 (France)

    2013-12-21

    The multi-channel optical readout of a THGEM multiplier coupled to a matrix of 3×3 Geiger-mode APDs (GAPDs) was demonstrated in a two-phase Cryogenic Avalanche Detector (CRAD) in Ar. The GAPDs recorded THGEM-hole avalanches in the Near Infrared (NIR) spectral range. At an avalanche charge gain of 160, the yield of the combined THGEM/GAPD-matrix multiplier amounted to ∼80 photoelectrons per 20 keV X-ray absorbed in the liquid phase. A spatial resolution of 2.5 mm (FWHM) has been measured for the impinging X-rays. This technique has potential applications in coherent neutrino-nucleus scattering and in dark matter search experiments.

  18. Non-Geiger-Mode Single-Photon Avalanche Detector with Low Excess Noise

    Science.gov (United States)

    Zhao, Kai; Lo, YuHwa; Farr, William

    2010-01-01

    This design constitutes a self-resetting (gain quenching), room-temperature operational semiconductor single-photon-sensitive detector that is sensitive to telecommunications optical wavelengths and is scalable to large areas (millimeter diameter) with high bandwidth and efficiencies. The device can detect single photons at a 1,550-nm wavelength at a gain of 1 x 10(exp 6). Unlike conventional single photon avalanche detectors (SPADs), where gain is an extremely sensitive function to the bias voltage, the multiplication gain of this device is stable at 1 x 10(exp 6) over a wide range of bias from 30.2 to 30.9 V. Here, the multiplication gain is defined as the total number of charge carriers contained in one output pulse that is triggered by the absorption of a single photon. The statistics of magnitude of output signals also shows that the device has a very narrow pulse height distribution, which demonstrates a greatly suppressed gain fluctuation. From the histograms of both pulse height and pulse charge, the equivalent gain variance (excess noise) is between 1.001 and 1.007 at a gain of 1 x 10(exp 6). With these advantages, the device holds promise to function as a PMT-like photon counter at a 1,550- nm wavelength. The epitaxial layer structure of the device allows photons to be absorbed in the InGaAs layer, generating electron/hole (e-h) pairs. Driven by an electrical field in InGaAs, electrons are collected at the anode while holes reach the multiplication region (InAlAs p-i-n structure) and trigger the avalanche process. As a result, a large number of e-h pairs are created, and the holes move toward the cathode. Holes created by the avalanche process gain large kinetic energy through the electric field, and are considered hot. These hot holes are cooled as they travel across a p -InAlAs low field region, and are eventually blocked by energy barriers formed by the InGaAsP/ InAlAs heterojunctions. The composition of the InGaAsP alloy was chosen to have an 80 me

  19. Depth of interaction resolution measurements for a high resolution PET detector using position sensitive avalanche photodiodes.

    Science.gov (United States)

    Yang, Yongfeng; Dokhale, Purushottam A; Silverman, Robert W; Shah, Kanai S; McClish, Mickel A; Farrell, Richard; Entine, Gerald; Cherry, Simon R

    2006-05-07

    We explore dual-ended read out of LSO arrays with two position sensitive avalanche photodiodes (PSAPDs) as a high resolution, high efficiency depth-encoding detector for PET applications. Flood histograms, energy resolution and depth of interaction (DOI) resolution were measured for unpolished LSO arrays with individual crystal sizes of 1.0, 1.3 and 1.5 mm, and for a polished LSO array with 1.3 mm pixels. The thickness of the crystal arrays was 20 mm. Good flood histograms were obtained for all four arrays, and crystals in all four arrays can be clearly resolved. Although the amplitude of each PSAPD signal decreases as the interaction depth moves further from the PSAPD, the sum of the two PSAPD signals is essentially constant with irradiation depth for all four arrays. The energy resolutions were similar for all four arrays, ranging from 14.7% to 15.4%. A DOI resolution of 3-4 mm (including the width of the irradiation band which is approximately 2 mm) was obtained for all the unpolished arrays. The best DOI resolution was achieved with the unpolished 1 mm array (average 3.5 mm). The DOI resolution for the 1.3 mm and 1.5 mm unpolished arrays was 3.7 and 4.0 mm respectively. For the polished array, the DOI resolution was only 16.5 mm. Summing the DOI profiles across all crystals for the 1 mm array only degraded the DOI resolution from 3.5 mm to 3.9 mm, indicating that it may not be necessary to calibrate the DOI response separately for each crystal within an array. The DOI response of individual crystals in the array confirms this finding. These results provide a detailed characterization of the DOI response of these PSAPD-based PET detectors which will be important in the design and calibration of a PET scanner making use of this detector approach.

  20. Large-Area Superconducting Nanowire Single-Photon Detector with Double-Stage Avalanche Structure

    OpenAIRE

    2016-01-01

    We propose a novel design of superconducting nanowire avalanche photodetectors (SNAPs), which combines the advantages of multi-stage avalanche SNAPs to lower the avalanche current I_AV and that of series-SNAPs to reduce the reset time. As proof of principle, we fabricated 800 devices with large detection area (15 um * 15 um) and five different designs on a single silicon chip for comparison, which include standard SNSPDs, series-3-SNAPs and our modified series-SNAPs with double-stage avalanch...

  1. Characterization of photo-multiplier tubes for the Cryogenic Avalanche Detector

    CERN Document Server

    Bondar, A; Dolgov, A; Nosov, V; Shekhtman, L; Sokolov, A

    2015-01-01

    New Cryogenic Avalanche Detector (CRAD) with ultimate sensitivity, that will be able to detect one primary electron released in the cryogenic liquid, is under development in the Laboratory of Cosmology and Particle Physics of the Novosibirsk State University jointly with the Budker Institute of Nuclear Physics. The CRAD will use two sets of cryogenic PMTs in order to get trigger signal either from primary scintillations in liquid Ar or from secondary scintillations in high field gap above the liquid. Two types of cryogenic PMTs produced by Hamamatsu Photonics were tested and the results are presented in this paper. Low background 3 inch PMT R11065- 10 demonstrated excellent performance according to its specifications provided by the producer. The gain measured with single electron response (SER) in liquid Ar reached 10^7, dark count rate rate did not exceed 300 Hz and pulse height resolution of single electron signals was close to 50%(FWHM). However, two R11065-10 PMTs out of 7 tested stopped functioning afte...

  2. Studies of a hybrid avalanche photo-detector in magnetic field

    Science.gov (United States)

    Šantelj, L.; Adachi, I.; Hataya, K.; Iori, S.; Iwata, S.; Kakuno, H.; Kataura, R.; Kawai, H.; Kindo, H.; Korpar, S.; Križan, P.; Mrvar, M.; Nath, K.; Nishida, S.; Ogawa, S.; Pestotnik, R.; Stanovnik, A.; Seljak, A.; Sumiyoshi, T.; Tabata, M.; Tahirovič, E.; Yusa, Y.

    2017-02-01

    For the Belle II spectrometer a proximity focusing RICH counter with an aerogel radiator (ARICH) will be employed as a PID system in the forward endcap region of the spectrometer. The main challenge was the development of a reliable multichannel sensor for single photons that operates in the high magnetic field of the spectrometer (1.5 T) and withstands the radiation levels expected at the experiment. A 144-channel Hybrid Avalanche Photo-Detector (HAPD) was developed with Hamamatsu Photonics K.K. and the mass production of ∼480 HAPDs was completed recently. While our first tests of HAPD performance in the magnetic field (before mass production) showed no issues, we lately observed a presence of very large signal pulses (∼5000× single photon signal), generated internally within about 20% of HAPDs, while operating in the magnetic field. The rate of these pulses varies from sample to sample. These pulses impact the HAPD performance in two ways: they introduce periods of dead time and, in some cases, damage to the front-end electronics was observed. Here we present conditions under which such large pulses are generated, their properties and impact on HAPD performance, and discuss possible mechanism of their origin.

  3. Simulation of computed radiography with imaging plate detectors

    Energy Technology Data Exchange (ETDEWEB)

    Tisseur, D.; Costin, M. [CEA LIST, CEA Saclay 91191 Gif sur Yvette Cedex (France); Mathy, F. [CEA-LETI, Campus Minatec, F-38054, Grenoble (France); Schumm, A. [EDF R and D, 1 avenue du général de gaulle 92141 Clamart (France)

    2014-02-18

    Computed radiography (CR) using phosphor imaging plate detectors is taking an increasing place in Radiography Testing. CR uses similar equipment as conventional radiography except that the classical X-ray film is replaced by a numerical detector, called image plate (IP), which is made of a photostimulable layer and which is read by a scanning device through photostimulated luminescence. Such digital radiography has already demonstrated important benefits in terms of exposure time, decrease of source energies and thus reduction of radioprotection area besides being a solution without effluents. This paper presents a model for the simulation of radiography with image plate detectors in CIVA together with examples of validation of the model. The study consists in a cross comparison between experimental and simulation results obtained on a step wedge with a classical X-ray tube. Results are proposed in particular with wire Image quality Indicator (IQI) and duplex IQI.

  4. Neutron detection with imaging plates Part II. Detector characteristics

    CERN Document Server

    Thoms, M

    1999-01-01

    On the basis of the physical processes described in Neutron detection with imaging plates - part I: image storage and readout [Nucl. Instr. and Meth. A 424 (1999) 26-33] detector characteristics, such as quantum efficiency, detective quantum efficiency, sensitivity to neutron- and gamma-radiation, readout time and dynamic range are predicted. It is estimated that quantum efficiencies and detective quantum efficiencies close to 100% can be reached making these kind of detectors interesting for a wide range of applications.

  5. Radiation hardness investigation of avalanche photodiodes for the Projectile Spectator Detector readout at the Compressed Baryonic Matter experiment

    Energy Technology Data Exchange (ETDEWEB)

    Kushpil, Vasilij [Nuclear Physics Institute, Academy of Sciences of the Czech Republic, Řež (Czech Republic); Mikhaylov, Vasily, E-mail: mikhaylov@ujf.cas.cz [Nuclear Physics Institute, Academy of Sciences of the Czech Republic, Řež (Czech Republic); Czech Technical University in Prague, Faculty of Nuclear Sciences and Physical Engineering, Prague (Czech Republic); Kushpil, Svetlana; Tlustý, Pavel; Svoboda, Ondrej; Kugler, Andrej [Nuclear Physics Institute, Academy of Sciences of the Czech Republic, Řež (Czech Republic)

    2015-07-01

    In this paper, we discuss results of avalanche photodiodes radiation tests for Projectile Spectator Detector at future Compressed Baryonic Matter experiment. The tests were carried out in Nuclear Physics Institute of ASCR in Řež using the cyclotron facility. Secondary neutron beam was used for irradiation because the main radiation damage in the Projectile Spectator Detector is caused by neutrons. Two types of the avalanche photodiodes from Zecotek and Ketek manufacturers were investigated. Special attention was given to the noise investigation and self-annealing after the irradiation. We have irradiated two Ketek PM3375 diodes with equivalent dose for 1 MeV neutrons equal to 2.5±0.2×10{sup 12} n/cm{sup 2}, and single Zecotek MAPD-3N diode with equivalent dose for 1 MeV neutrons equal to 3.4±0.2×10{sup 12} n/cm{sup 2}. All the types of the diodes have shown an increasing level of the noise after the irradiation. From that we can conclude that those avalanche photodiodes are not able to detect single photons anymore due to high noise levels.

  6. A new modeling and simulation method for important statistical performance prediction of single photon avalanche diode detectors

    Science.gov (United States)

    Xu, Yue; Xiang, Ping; Xie, Xiaopeng; Huang, Yang

    2016-06-01

    This paper presents a new modeling and simulation method to predict the important statistical performance of single photon avalanche diode (SPAD) detectors, including photon detection efficiency (PDE), dark count rate (DCR) and afterpulsing probability (AP). Three local electric field models are derived for the PDE, DCR and AP calculations, which show analytical dependence of key parameters such as avalanche triggering probability, impact ionization rate and electric field distributions that can be directly obtained from Geiger mode Technology Computer Aided Design (TCAD) simulation. The model calculation results are proven to be in good agreement with the reported experimental data in the open literature, suggesting that the proposed modeling and simulation method is very suitable for the prediction of SPAD statistical performance.

  7. Characterization of photo-multiplier tubes for the Cryogenic Avalanche Detector

    Science.gov (United States)

    Bondar, A.; Buzulutskov, A.; Dolgov, A.; Nosov, V.; Shekhtman, L.; Sokolov, A.

    2015-10-01

    New Cryogenic Avalanche Detector (CRAD) with ultimate sensitivity, that will be able to detect one primary electron released in the cryogenic liquid, is under development in the Laboratory of Cosmology and Particle Physics of the Novosibirsk State University jointly with the Budker Institute of Nuclear Physics. The CRAD will use two sets of cryogenic PMTs in order to get trigger signal either from primary scintillations in liquid Ar or from secondary scintillations in high field gap above the liquid. Two types of cryogenic PMTs produced by Hamamatsu Photonics were tested and the results are presented in this paper. Low background 3 inch PMT R11065-10 demonstrated excellent performance according to its specifications provided by the producer. The gain measured with single electron response (SER) in liquid Ar reached 107, dark count rate rate did not exceed 300 Hz and pulse height resolution of single electron signals was close to 50%(FWHM). However, two R11065-10 PMTs out of 7 tested stopped functioning after several tens minutes of operation immersed completely into liquid Ar. The remaining 5 devices and one R11065-MOD were operated successfully for several hours each with all the parameters according to the producer specifications. Compact 2 inch PMT R6041-506-MOD with metal-channel dynode structure is a candidate for side wall PMT system that will look at electroluminescence in high field region above liquid. Four of these PMTs were tested in liquid Ar and demonstrated gain up to 2× 107, dark count rate rate below 100 Hz and pulse height resolution of single electron signals of about 110% (FWHM).

  8. Development of a 144-channel Hybrid Avalanche Photo-Detector for Belle II ring-imaging Cherenkov counter with an aerogel radiator

    Energy Technology Data Exchange (ETDEWEB)

    Nishida, S., E-mail: shohei.nishida@kek.jp [High Energy Accelerator Research Organization (KEK), Tsukuba (Japan); Adachi, I. [High Energy Accelerator Research Organization (KEK), Tsukuba (Japan); Hamada, N. [Toho University, Funabashi (Japan); Hara, K. [High Energy Accelerator Research Organization (KEK), Tsukuba (Japan); Iijima, T. [Nagoya University, Nagoya (Japan); Iwata, S.; Kakuno, H. [Tokyo Metropolitan University, Hachioji (Japan); Kawai, H. [Chiba University, Chiba (Japan); Korpar, S.; Krizan, P. [Jozef Stefan Institute, Ljubljana (Slovenia); Ogawa, S. [Toho University, Funabashi (Japan); Pestotnik, R.; Ŝantelj, L.; Seljak, A. [Jozef Stefan Institute, Ljubljana (Slovenia); Sumiyoshi, T. [Tokyo Metropolitan University, Hachioji (Japan); Tabata, M. [Chiba University, Chiba (Japan); Tahirovic, E. [Jozef Stefan Institute, Ljubljana (Slovenia); Yoshida, K. [Tokyo Metropolitan University, Hachioji (Japan); Yusa, Y. [Niigata University, Niigata (Japan)

    2015-07-01

    The Belle II detector, a follow up of the very successful Belle experiment, is under construction at the SuperKEKB electron–positron collider at KEK in Japan. For the PID system in the forward region of the spectrometer, a proximity-focusing ring-imaging Cherenkov counter with an aerogel radiator is being developed. For the position sensitive photon sensor, a 144-channel Hybrid Avalanche Photo-Detector has been developed with Hamamatsu Photonics K.K. In this report, we describe the specification of the Hybrid Avalanche Photo-Detector and the status of the mass production.

  9. Single Photon Sensitive HgCdTe Avalanche Photodiode Detector (APD) Project

    Data.gov (United States)

    National Aeronautics and Space Administration — A linear mode HgCdT electron-initiated avalanche photodiode (EAPD) capable of 1570nm photon detection efficiency (PDE) at >10 MHz will be developed. The Phase I...

  10. Technology developments and first measurements on inverse Low Gain Avalanche Detector (iLGAD) for high energy physics applications

    CERN Document Server

    Carulla, M.; Fernández-Martínez, P.; IMB-CNM (CSIC); Flores, D.; IMB-CNM (CSIC); González, J.; Hidalgo, S.; Jaramillo, R.; Merlos, A.; Palomo, F.R.; Pellegrini, G; Quirion, D.; Vila, I.

    2016-01-01

    ABSTRACT: The first Inverse Low Gain Avalanche Detector (iLGAD) have been fabricated at IMB-CNM (CSIC). The iLGAD structure includes the multiplication diffusions at the ohmic contact side while the segmentation is implemented at the front side with multiple P + diffusions. Therefore, iLGAD is P on P position-sensitive detector with a uniform electric field all along the device area that guarantees the same signal amplification wherever a particle passes through the sensitive bulk solving the main draw of the LGAD microstrip detector. However, the detection current is dominated by holes flowing back from the multiplication junction with the subsequent transient current pulse duration increase in comparison with conventional LGAD counterparts. Applications of iLGAD range from tracking and timing applications like determination of primary interaction vertex to medical imaging. The paper addresses the optimization of the iLGAD structure with the aid of TCAD simul...

  11. Simulation of Low Gain Avalanche Detector characteristics based on the concept of negative feedback in irradiated silicon detectors with carrier impact ionization

    Science.gov (United States)

    Verbitskaya, E.; Eremin, V.; Zabrodskii, A.; Luukka, P.

    2016-12-01

    In this study the main characteristics of silicon Low Gain Avalanche Detectors (LGAD), the dependencies of the collected charge versus bias voltage and fluence, are calculated to fit experimental data. The calculations are based on two previously developed Ioffe Institute models of radiation degradation in Si detectors: 1) a model of two effective energy levels of radiation-induced defects, and 2) a mechanism of internal negative feedback responsible for the gain degradation in irradiated Si detectors originating from the avalanche multiplication at the detector junction. The combination of these models describes well the properties of irradiated p-i-n detectors in a wide range of fluences. For simulating the LGAD characteristics the models are adapted to its n+-pbi-p-p+ structure, where the built-in boron-doped layer pbi produces high electric field sufficient for carrier impact ionization. It is shown that the developed models give adequate quantitative description of the experimental results for the LGADs up to the fluence of 2×1015 n/cm2 including the detector pulse response; however, additional boron removal from the pbi layer is required to have the best correlation with the experimental data. Similar to the physical model developed for silicon strip detectors operated at high voltage, the results are interpreted in terms of the internal negative feedback mechanism. It is shown that in irradiated LGADs this feedback leads to the transfer of a significant fraction of the potential drop from the built-in layer toward the p+ contact. It initiates two negative effects, which both cause the gain degradation with irradiation: the lowering of the electric field in the n+-pbi region that reduces the multiplication probability, and the increase of the collection time and trapping-related charge losses.

  12. Saturation effects in heterodyne detection with Geiger-mode InGaAs avalanche photodiode detector arrays.

    Science.gov (United States)

    Luu, Jane X; Jiang, Leaf A

    2006-06-01

    We report, to the best of our knowledge, the first demonstration of heterodyne detection of a glint target using an InGaAs avalanche photodiode detector (APD) array in the Geiger mode. Due to the finite number of pixels, all such photon-counting arrays necessarily suffer from saturation effects. At large photon fluxes, saturation of the APD degrades the Doppler frequency resolution and the signal-to-noise ratio (SNR). We derive analytical expressions for the Doppler resolution and SNR, taking saturation effects into account. The optimal local oscillator power can be obtained numerically from the SNR expression.

  13. Analysis of Interplanetary Dust Experiment Detectors and Other Witness Plates

    Science.gov (United States)

    Griffis, D. P.; Wortman, J. J.

    1992-01-01

    The development of analytical procedures for identifying the chemical composition of residue from impacts that occurred on the Interplanetary Dust Experiment (IDE) detectors during the flight of Long Duration Exposure Facility (LDEF) and the carrying out of actual analysis on IDE detectors and other witness plates are discussed. Two papers on the following topics are presented: (1) experimental analysis of hypervelocity microparticle impact sites on IDE sensor surfaces; and (2) contaminant interfaces with secondary Ion Mass Spectrometer (SIMS) analysis of microparticle impactor residues on LDEF surfaces.

  14. The Detector Control Systems for the CMS Resistive Plate Chamber

    CERN Document Server

    Paolucci, P; Gómez-Reino, R; Viviani, C; Shahzad, R; Khurshid, T

    2010-01-01

    The Resistive Plate Chamber system is composed by 912 double-gap chambers equipped with about $10^4$ front-end boards. The correct and safe operation of the RPC system requires a sophisticated and complex online Detector Control System, able to monitor and control 2$\\cdot10^4$ hardware devices distributed on an area of about 5000 m$^2$. The RPC DCS acquires, monitors and stores about $10^5$ parameters coming from the detector, the electronics, the power system, the gas, and cooling systems. The DCS system and the first results, obtained during the 2007 and 2008 CMS cosmic runs, will be described in this paper.

  15. Dead-time effects in microchannel-plate imaging detectors

    Science.gov (United States)

    Zombeck, Martin V.; Fraser, George W.

    1991-01-01

    The observed counting rates of microchannel plate (MCP) based detectors for high resolution observations of celestial EUV and X-ray sources vary over many orders of magnitude; the counting capability of an individual channel, however, is not high, and is associated with dead-times ranging from 0.1 msec to 1 sec. The dead-time increases with the area illuminated; attention is presently given to laboratory determinations of the count rate characteristics of a MCP detector as a function of illuminated area, and a model is developed for these results' use in the interpretation of space observations.

  16. Non-Markovian property of afterpulsing effect in single-photon avalanche detector

    CERN Document Server

    Wang, Fang-Xiang; Li, Ya-Ping; He, De-Yong; Wang, Chao; Han, Yun-Guang; Wang, Shuang; Yin, Zhen-Qiang; Han, Zheng-Fu

    2016-01-01

    The single-photon avalanche photodiode(SPAD) has been widely used in research on quantum optics. The afterpulsing effect, which is an intrinsic character of SPAD, affects the system performance in most experiments and needs to be carefully handled. For a long time, afterpulsing has been presumed to be determined by the pre-ignition avalanche. We studied the afterpulsing effect of a commercial InGaAs/InP SPAD (The avalanche photodiode model is: Princeton Lightwave PGA-300) and demonstrated that its afterpulsing is non-Markovian, with a memory effect in the avalanching history. Theoretical analysis and experimental results clearly indicate that the embodiment of this memory effect is the afterpulsing probability, which increases as the number of ignition-avalanche pulses increase. This conclusion makes the principle of the afterpulsing effect clearer and is instructive to the manufacturing processes and afterpulsing evaluation of high-count-rate SPADs. It can also be regarded as a fundamental premise to handle ...

  17. A Directional Gamma-Ray Detector Based on Scintillator Plates

    CERN Document Server

    Hanna, D; Boyle, P; MacLeod, A M L

    2015-01-01

    A simple device for determining the azimuthal location of a source of gamma radiation, using ideas from astrophysical gamma-ray burst detection, is described. A compact and robust detector built from eight identical modules, each comprising a plate of CsI(Tl) scintillator coupled to a photomultiplier tube, can locate a point source of gamma rays with degree-scale precision by comparing the count rates in the different modules. Sensitivity to uniform environmental background is minimal.

  18. Design and testing of an active quenching circuit for an avalanche photodiode photon detector

    Science.gov (United States)

    Arbel, D.; Schwartz, J. A.

    1991-01-01

    The photon-detection capabilities of avalanche photodiodes (APDs) operating above their theoretical breakdown voltages are described, with particular attention given to the needs and methods of quenching an avalanche once breakdown has occurred. A brief background on the motives of and previous work with this mode of operation is presented. Finally, a description of the design and testing of an active quenching circuit is given. Although the active quenching circuit did not perform as expected, knowledge was gained as to the signal amplitudes necessary for quenching and the need for a better model for the above-breakdown circuit characteristics of the Geiger-mode APD.

  19. Scintillator counters with multi-pixel avalanche photodiode readout for the ND280 detector of the T2K experiment

    Energy Technology Data Exchange (ETDEWEB)

    Mineev, O. [Institute for Nuclear Research of RAS, INR RAS, 60th October Revolution Pr. 7a, 117312 Moscow (Russian Federation)]. E-mail: oleg@inr.ru; Afanasjev, A. [Institute for Nuclear Research of RAS, INR RAS, 60th October Revolution Pr. 7a, 117312 Moscow (Russian Federation); Bondarenko, G.; Golovin, V. [Center of Perspective Technology and Apparatus, 107076 Moscow (Russian Federation); Gushchin, E.; Izmailov, A.; Khabibullin, M.; Khotjantsev, A. [Institute for Nuclear Research of RAS, INR RAS, 60th October Revolution Pr. 7a, 117312 Moscow (Russian Federation); Kudenko, Yu. [Institute for Nuclear Research of RAS, INR RAS, 60th October Revolution Pr. 7a, 117312 Moscow (Russian Federation); Kurimoto, Y. [Department of Physics, Kyoto University, Kyoto 606-8502 (Japan); Kutter, T. [Department of Physics and Astronomy, Louisiana State University, Baton Rouge, Louisiana 70803-4001 (United States); Lubsandorzhiev, B. [Institute for Nuclear Research of RAS, INR RAS, 60th October Revolution Pr. 7a, 117312 Moscow (Russian Federation); Mayatski, V. [AO Uniplast, 600016 Vladimir (Russian Federation); Musienko, Yu. [Institute for Nuclear Research of RAS, INR RAS, 60th October Revolution Pr. 7a, 117312 Moscow (Russian Federation); Nakaya, T.; Nobuhara, T. [Department of Physics, Kyoto University, Kyoto 606-8502 (Japan); Shaibonov, B.A.J.; Shaikhiev, A. [Institute for Nuclear Research of RAS, INR RAS, 60th October Revolution Pr. 7a, 117312 Moscow (Russian Federation); Taguchi, M. [Department of Physics, Kyoto University, Kyoto 606-8502 (Japan); Yershov, N. [Institute for Nuclear Research of RAS, INR RAS, 60th October Revolution Pr. 7a, 117312 Moscow (Russian Federation); Yokoyama, M. [Department of Physics, Kyoto University, Kyoto 606-8502 (Japan)

    2007-07-11

    The Tokai-to-Kamioka (T2K) experiment is a second generation long baseline neutrino oscillation experiment which aims at a sensitive search for {nu}{sub e} appearance. The main design features of the T2K near neutrino detectors located at 280m from the target are presented, and the scintillator counters are described. The counters are readout via WLS fibers embedded into S-shaped grooves in the scintillator from both ends by multi-pixel avalanche photodiodes operating in a limited Geiger mode. Operating principles and results of tests of photosensors with a sensitive area of 1mm{sup 2} are presented. A time resolution of 1.75ns, a spatial resolution of 9.9-12.4cm, and a detection efficiency for minimum ionizing particles of more than 99% were obtained for scintillator detectors in a beam test.

  20. Imaging characteristics of the Extreme Ultraviolet Explorer microchannel plate detectors

    Science.gov (United States)

    Vallerga, J. V.; Kaplan, G. C.; Siegmund, O. H. W.; Lampton, M.; Malina, R. F.

    1989-01-01

    The Extreme Ultraviolet Explorer (EUVE) satellite will conduct an all-sky survey over the wavelength range from 70 A to 760 A using four grazing-incidence telescopes and seven microchannel-plate (MCP) detectors. The imaging photon-counting MCP detectors have active areas of 19.6 cm2. Photon arrival position is determined using a wedge-and-strip anode and associated pulse-encoding electronics. The imaging characteristics of the EUVE flight detectors are presented including image distortion, flat-field response, and spatial differential nonlinearity. Also included is a detailed discussion of image distortions due to the detector mechanical assembly, the wedge-and-strip anode, and the electronics. Model predictions of these distortions are compared to preflight calibration images which show distortions less than 1.3 percent rms of the detector diameter of 50 mm before correction. The plans for correcting these residual detector image distortions to less than 0.1 percent rms are also presented.

  1. Development and Improvement of Position Sensitive Parallel Plate Avalanche Counter (PS-PPAC)

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    A series of PS-PPAC was developed and the position resolution was successively improved by us in order to meet the need of heavy ion physics research.The PS-PPAC may be divided into two groups.1 PS-PPAC used for stable(ion)bearna)Double grid position sensitive avalanche chamber(DGAC)~[1].DGAC consists of 4 electrodes:anode A,cathode C,grids K and G,which are made of wire planes.The sensitive area was 25×20 cm~2.A position

  2. Non-Markov property of afterpulsing effect in single-photon avalanche detector

    CERN Document Server

    Wang, Fang-Xiang; Li, Ya-Ping; He, De-Yong; Wang, Chao; Han, Yun-Guang; Wang, Shuang; Yin, Zhen-Qiang; Han, Zheng-Fu

    2016-01-01

    Single-photon avalanche photodiode(SPAD) has been widely used in researching of quantum optics. Afterpulsing effect, which is an intrinsic character of SPAD, affects the system performance in most of the experiments and needs to be carefully handled. For a long time, afterpulsing has been presumed to be determined by the pre-ignition avalanche. We studied the afterpulsing effect of a commercial InGaAs/InP SPAD (APD: Princeton Lightwave PGA-300) and demonstrated that its afterpulsing is non-Markov, which has memory effect of the avalanching history. Theoretical analysis and the experimental results clearly indicate that the embodiment of this memory effect is the afterpulsing probability, which increases as the number of ignition-avalanche pulses increase. The conclusion makes the principle of afterpulsing effect clearer and is instructive to the manufacturing processes and afterpulsing evaluation of high-count-rate SPADs. It can also be regarded as an fundamental premise to handle the afterpulsing signals in ...

  3. Technology developments and first measurements on inverse Low Gain Avalanche Detector (iLGAD) for high energy physics applications

    Science.gov (United States)

    Carulla, M.; Fernández-García, M.; Fernández-Martínez, P.; Flores, D.; González, J.; Hidalgo, S.; Jaramillo, R.; Merlos, A.; Palomo, F. R.; Pellegrini, G.; Quirion, D.; Vila, I.

    2016-12-01

    The first Inverse Low Gain Avalanche Detector (iLGAD) have been fabricated at IMB-CNM (CSIC). The iLGAD structure includes the multiplication diffusions at the ohmic contact side while the segmentation is implemented at the front side with multiple p+ diffusions. Therefore, iLGAD is p on p position-sensitive detector with a uniform electric field all along the device area that guarantees the same signal amplification wherever a particle passes through the sensitive bulk solving the main draw of the LGAD microstrip detector. However, the detection current is dominated by holes flowing back from the multiplication junction with the subsequent increase of the transient current pulse duration in comparison with conventional LGAD counterparts. Applications of iLGAD range from tracking and timing applications, like determination of primary interaction vertex, to medical imaging. The paper addresses the optimization of the iLGAD structure with the aid of TCAD simulations, focusing on the electric field profiles of iLGAD and LGAD microstrip structures and the corresponding gain. The electrical performance of the first fabricated samples is also provided. For the first time, we have the experimental demonstration of the signal amplification of these novel iLGAD detectors.

  4. Application of imaging plate neutron detector to neutron radiography

    CERN Document Server

    Fujine, S; Kamata, M; Etoh, M

    1999-01-01

    As an imaging plate neutron detector (IP-ND) has been available for thermal neutron radiography (TNR) which has high resolution, high sensitivity and wide range, some basic characteristics of the IP-ND system were measured at the E-2 facility of the KUR. After basic performances of the IP were studied, images with high quality were obtained at a neutron fluence of 2 to 7x10 sup 8 n cm sup - sup 2. It was found that the IP-ND system with Gd sub 2 O sub 3 as a neutron converter material has a higher sensitivity to gamma-ray than that of a conventional film method. As a successful example, clear radiographs of the flat view for the fuel side plates with boron burnable poison were obtained. An application of the IP-ND system to neutron radiography (NR) is presented in this paper.

  5. A High Position Resolution X-ray Detector: an Edge on Illuminated Capillary Plate Combined with a Gas Amplification Structure

    CERN Document Server

    Iacobaeus, C; Lund-Jensen, B; Ostling, J; Pavlopoulos, P; Peskov, Vladimir; Tokanai, F

    2006-01-01

    We have developed and successfully tested a prototype of a new type of high position resolution hybrid X-ray detector. It contains a thin wall lead glass capillary plate converter of X-rays combined with a microgap parallel-plate avalanche chamber filled with gas at 1 atm. The operation of these converters was studied in a wide range of X-ray energies (from 6 to 60 keV) at incident angles varying from 0-90 degree. The detection efficiency, depending on the geometry, photon energy, incident angle and the mode of operation, was between 5-30 percent in a single step mode and up to 50 percent in a multi-layered combination. Depending on the capillary geometry, the position resolution achieved was between 0.050-0.250 mm in digital form and was practically independent of the photon energy or gas mixture. The usual lead glass capillary plates operated without noticeable charging up effects at counting rates of 50 Hz/mm2, and hydrogen treated capillaries up to 10E5 Hz/mm2. The developed detector may open new possibil...

  6. Indirect flat-panel detector with avalanche gain: fundamental feasibility investigation for SHARP-AMFPI (scintillator HARP active matrix flat panel imager).

    Science.gov (United States)

    Zhao, Wei; Li, Dan; Reznik, Alla; Lui, B J M; Hunt, D C; Rowlands, J A; Ohkawa, Yuji; Tanioka, Kenkichi

    2005-09-01

    An indirect flat-panel imager (FPI) with avalanche gain is being investigated for low-dose x-ray imaging. It is made by optically coupling a structured x-ray scintillator CsI(Tl) to an amorphous selenium (a-Se) avalanche photoconductor called HARP (high-gain avalanche rushing photoconductor). The final electronic image is read out using an active matrix array of thin film transistors (TFT). We call the proposed detector SHARP-AMFPI (scintillator HARP active matrix flat panel imager). The advantage of the SHARP-AMFPI is its programmable gain, which can be turned on during low dose fluoroscopy to overcome electronic noise, and turned off during high dose radiography to avoid pixel saturation. The purpose of this paper is to investigate the important design considerations for SHARP-AMFPI such as avalanche gain, which depends on both the thickness d(Se) and the applied electric field E(Se) of the HARP layer. To determine the optimal design parameter and operational conditions for HARP, we measured the E(Se) dependence of both avalanche gain and optical quantum efficiency of an 8 microm HARP layer. The results were used in a physical model of HARP as well as a linear cascaded model of the FPI to determine the following x-ray imaging properties in both the avalanche and nonavalanche modes as a function of E(Se): (1) total gain (which is the product of avalanche gain and optical quantum efficiency); (2) linearity; (3) dynamic range; (4) gain nonuniformity resulting from thickness nonuniformity; and (5) effects of direct x-ray interaction in HARP. Our results showed that a HARP layer thickness of 8 microm can provide adequate avalanche gain and sufficient dynamic range for x-ray imaging applications to permit quantum limited operation over the range of exposures needed for radiography and fluoroscopy.

  7. Performance measurements of a depth-encoding PET detector module based on position-sensitive avalanche photodiode read-out.

    Science.gov (United States)

    Dokhale, P A; Silverman, R W; Shah, K S; Grazioso, R; Farrell, R; Glodo, J; McClish, M A; Entine, G; Tran, V H; Cherry, S R

    2004-09-21

    We are developing a high-resolution, high-efficiency positron emission tomography (PET) detector module with depth of interaction (DOI) capability based on a lutetium oxyorthosilicate (LSO) scintillator array coupled at both ends to position-sensitive avalanche photodiodes (PSAPDs). In this paper we present the DOI resolution, energy resolution and timing resolution results for complete detector modules. The detector module consists of a 7 x 7 matrix of LSO scintillator crystals (1 x 1 x 20 mm3 in dimension) coupled to 8 x 8 mm2 PSAPDs at both ends. Flood histograms were acquired and used to generate crystal look-up tables. The DOI resolution was measured for individual crystals within the array by using the ratio of the signal amplitudes from the two PSAPDs on an event-by-event basis. A measure of the total scintillation light produced was obtained by summing the signal amplitudes from the two PSAPDs. This summed signal was used to measure the energy resolution. The DOI resolution was measured to be 3-4 mm FWHM irrespective of the position of the crystal within the array, or the interaction location along the length of the crystal. The total light signal and energy resolution was almost independent of the depth of interaction. The measured energy resolution averaged 14% FWHM. The coincidence timing resolution measured using a pair of identical detector modules was 4.5 ns FWHM. These results are consistent with the design goals and the performance required of a compact, high-resolution and high-efficiency PET detector module for small animal and breast imaging applications.

  8. The 1.06 micrometer avalanche photodiode detectors with integrated circuit preamplifiers

    Science.gov (United States)

    Eden, R. C.

    1975-01-01

    The development of a complete solid state 1.06 micron optical receiver which can be used in optical communications at data rates approaching 1.5 Gb/s, or in other applications requiring sensitive, short-pulse detection, is reported. This work entailed both the development of a new type of heterojunction 3-5 semiconductor alloy avalanche photodiode and an extremely charge-sensitive wideband low-noise preamp design making use of GaAs Schottky barrier-gate field effect transistors.

  9. Large-area NbN superconducting nanowire avalanche photon detectors with saturated detection efficiency

    Science.gov (United States)

    Murphy, Ryan P.; Grein, Matthew E.; Gudmundsen, Theodore J.; McCaughan, Adam; Najafi, Faraz; Berggren, Karl K.; Marsili, Francesco; Dauler, Eric A.

    2015-05-01

    Superconducting circuits comprising SNSPDs placed in parallel—superconducting nanowire avalanche photodetectors, or SNAPs—have previously been demonstrated to improve the output signal-to-noise ratio (SNR) by increasing the critical current. In this work, we employ a 2-SNAP superconducting circuit with narrow (40 nm) niobium nitride (NbN) nanowires to improve the system detection efficiency to near-IR photons while maintaining high SNR. Additionally, while previous 2-SNAP demonstrations have added external choke inductance to stabilize the avalanching photocurrent, we show that the external inductance can be entirely folded into the active area by cascading 2-SNAP devices in series to produce a greatly increased active area. We fabricated series-2-SNAP (s2-SNAP) circuits with a nanowire length of 20 μm with cascades of 2-SNAPs providing the choke inductance necessary for SNAP operation. We observed that (1) the detection efficiency saturated at high bias currents, and (2) the 40 nm 2-SNAP circuit critical current was approximately twice that for a 40 nm non-SNAP configuration.

  10. Detection efficiency evaluation for a large area neutron sensitive microchannel plate detector

    CERN Document Server

    Wang, Yiming; Liu, Ren

    2016-01-01

    In this paper, the detection efficiency of a large area neutron sensitive microchannel plate detector has been evaluated. A 6LiF/ZnS detector was employed as the benchmark detector, the TOF spectra of these two detectors were simultaneously measured and the energy spectra were then deduced to calculate the detection efficiency curve of the nMCP detector. Tests show the detection efficiency@25.3 meV thermal neutron is 34% for this nMCP detector.

  11. Near infrared single photon avalanche detector with negative feedback and self quenching

    Science.gov (United States)

    Linga, Krishna; Yevtukhov, Yuriy; Liang, Bing

    2009-08-01

    We present the design and development of a negative feedback devices using the internal discrete amplifier approach used for the development of a single photon avalanche photodetector in the near infrared wavelength region. This new family of photodetectors with negative feedback, requiring no quenching mechanism using Internal Discrete Amplification (IDA) mechanism for the realization of very high gain and low excess noise factor in the visible and near infrared spectral regions, operates in the non-gated mode under a constant bias voltage. The demonstrated device performance far exceeds any available solid state Photodetectors in the near infrared wavelength range. The measured devices have Gain > 2×105, Excess noise factor Lidar, free space optical communication, 3D imaging, industrial and scientific instrumentation, night vision, quantum cryptography, and other military, defence and aerospace applications.

  12. CHICO2, a two-dimensional pixelated parallel-plate avalanche counter

    Energy Technology Data Exchange (ETDEWEB)

    Wu, C.Y., E-mail: wu24@llnl.gov [Lawrence Livermore National Laboratory, Livermore, CA 94551 (United States); Cline, D.; Hayes, A.; Flight, R.S.; Melchionna, A.M.; Zhou, C. [Department of Physics and Astronomy, University of Rochester, Rochester, NY 14627 (United States); Lee, I.Y. [Nuclear Science Division, Lawrence Berkeley National Laboratory, Berkeley, CA 94720 (United States); Swan, D. [Swan Research LLC, Owosso, MI 48867 (United States); Fox, R. [CAEN Technologies, INC, Staten Island, NY 10305 (United States); Anderson, J.T. [High Energy Physics Division, Argonne National Laboratory, Argonne, IL 60439 (United States)

    2016-04-01

    CHICO2 (Compact Heavy Ion COunter), is a large solid-angle, charged-particle detector array developed to provide both θ and ϕ angle resolutions matching those of GRETINA (Gamma-Ray Energy Tracking In-beam Nuclear Array). CHICO2 was successfully tested at the Argonne National Laboratory where it was fielded as an auxiliary detector with GRETINA for γ-ray spectroscopic studies of nuclei using a {sup 252}Cf spontaneous fission source, stable beams, and radioactive beams from CARIBU. In field tests of the {sup 72,76}Ge beams on a 0.5 mg/cm{sup 2208}Pb target at the sub-barrier energy, CHICO2 provided charged-particle angle resolutions (FWHM) of 1.55° in θ and 2.47° in ϕ. This achieves the design goal for both coordinates assuming a beam-spot size (>3 mm) and the target thickness (>0.5 mg/cm{sup 2}). The combined angular resolution of GRETINA/CHICO2 resulted in a Doppler-shift corrected energy resolution of 0.60% for 1 MeV coincident de-excitation γ-rays. This is nearly a factor of two improvements in resolution and sensitivity compared to Gammasphere/CHICO. Kinematically-coincident detection of scattered ions by CHICO2 still maintains the mass resolution (ΔM/M) of ~5% that enhanced isolation of scattered weak beams of interest from scattered contaminant beams.

  13. Fast Micro-Channel Plate Detector for MIPs

    CERN Document Server

    Antropov, A E; Kasatkin, V A; Klempt, W; Kolojvari, A A; Kondratev, V P; Martinov, V; Lazarev, V A; Novikov, I A; Potapov, S V; Stolyarov, O I; Tsimbal, F A; Tulina, T A; Valiev, F F; Vinogradov, L I

    1999-01-01

    Abstract for the 6th International Conference on Advanced Technology and Particle Physics, to be held at Villa Olmo, Como, Italy, 5-9 October 1998. For a couple of the last decades Micro-channel plates (MCPs) are known as a fast (1 ns), fine granularity (5-12µ), high gain (103 -104), excellent time resolution (30-50 ps), high counting rate (1011 1/cm2 was reported) and efficient detector widely used in low energy nuclear physics. Nevertheless, these nice features have not been exploited sufficiently in the high energy experiments so far. The use of MCPs in the HEP experiments demands the developments of technologies different from the low-energy applications: in particular the low mass vacuum thin-wall chambers in the UHV technique. It is the great intrinsic capability of the MCPs for the registration of MIPs, high gain and sharp signals that prompted us to develop a fast multiplicity detector for ALICE at the LHC. The chevron MCP setup (gain up to 10*8) gives a strong signal for the Ultra High Freq...

  14. Linear terrestrial laser scanning using array avalanche photodiodes as detectors for rapid three-dimensional imaging.

    Science.gov (United States)

    Cai, Yinqiao; Tong, Xiaohua; Tong, Peng; Bu, Hongyi; Shu, Rong

    2010-12-01

    As an active remote sensor technology, the terrestrial laser scanner is widely used for direct generation of a three-dimensional (3D) image of an object in the fields of geodesy, surveying, and photogrammetry. In this article, a new laser scanner using array avalanche photodiodes, as designed by the Shanghai Institute of Technical Physics of the Chinese Academy of Sciences, is introduced for rapid collection of 3D data. The system structure of the new laser scanner is first presented, and a mathematical model is further derived to transform the original data to the 3D coordinates of the object in a user-defined coordinate system. The performance of the new laser scanner is tested through a comprehensive experiment. The result shows that the new laser scanner can scan a scene with a field view of 30° × 30° in 0.2 s and that, with respect to the point clouds obtained on the wall and ground floor surfaces, the root mean square errors for fitting the two planes are 0.21 and 0.01 cm, respectively. The primary advantages of the developed laser scanner include: (i) with a line scanning mode, the new scanner achieves simultaneously the 3D coordinates of 24 points per single laser pulse, which enables it to scan faster than traditional scanners with a point scanning mode and (ii) the new scanner makes use of two galvanometric mirrors to deflect the laser beam in both the horizontal and the vertical directions. This capability makes the instrument smaller and lighter, which is more acceptable for users.

  15. Calibration of photon counting imaging microchannel plate detectors for EUV astronomy

    Science.gov (United States)

    Siegmund, O. H. W.; Vallerga, J.; Jelinsky, P.

    1986-01-01

    The calibration of photon counting imaging detectors for satellite based EUV astronomy is a complex process designed to ensure the validity of the data received 'in orbit'. The methods developed to accomplish calibration of microchannel plate detectors for the Extreme Ultraviolet Explorer are described and illustrated. The characterization of these detectors can be subdivided into three categories: stabilization, performance tests, and environmental tests.

  16. Effects of SF$_{6}$ on the avalanche mode operation of a real-sized double-gap resistive plate chamber for the Compact Muon Solenoid experiment

    CERN Document Server

    Ahn Sung Hwan; Hong, B; Hong, S J; Ito, M; Kim, B I; Kim, J H; Kim, Y J; Kim, Y U; Koo, D G; Lee, H W; Lee, K B; Lee, K S; Lee, S J; Lim, J K; Moon, D H; Nam, S K; Park, S; Park, W J; Rhee, J T; Ryu, M S; Shim, H H; Sim, K S; Kang, T I

    2005-01-01

    We present the design and the test, results for a real-sized prototype resistive plate chamber by using cosmic-ray muons for the forward region of the Compact Muon Solenoid (CMS) experiment at the Large Hadron Collider (LHC). In particular, we investigate the effects of adding SF/sub 6/ to the gas mixture for the avalanche mode operation of a resistive plate chamber. A small fraction of SF/sub 6/ is very effective in suppressing streamer signals in a resistive plate chamber. The shapes of the muon detection efficiency and the muon cluster size remain similar, but are shifted to higher operating voltage by SF/sub 6/. The noise cluster rate and size are not influenced by SF/sub 6/.

  17. Neutron diffractometer for bio-crystallography (BIX) with an imaging plate neutron detector

    Energy Technology Data Exchange (ETDEWEB)

    Niimura, Nobuo [Japan Atomic Energy Research Inst., Ibaraki-ken (Japan)

    1994-12-31

    We have constructed a dedicated diffractometer for neutron crystallography in biology (BIX) on the JRR-3M reactor at JAERI (Japan Atomic Energy Research Institute). The diffraction intensity from a protein crystal is weaker than that from most inorganic materials. In order to overcome the intensity problem, an elastically bent silicon monochromator and a large area detector system were specially designed. A preliminary result of diffraction experiment using BIX has been reported. An imaging plate neutron detector has been developed and a feasibility experiment was carried out on BIX. Results are reported. An imaging plate neutron detector has been developed and a feasibility test was carried out using BIX.

  18. Monte Carlo simulations of microchannel plate detectors I: steady-state voltage bias results

    Energy Technology Data Exchange (ETDEWEB)

    Ming Wu, Craig Kruschwitz, Dane Morgan, Jiaming Morgan

    2008-07-01

    X-ray detectors based on straight-channel microchannel plates (MCPs) are a powerful diagnostic tool for two-dimensional, time-resolved imaging and timeresolved x-ray spectroscopy in the fields of laser-driven inertial confinement fusion and fast z-pinch experiments. Understanding the behavior of microchannel plates as used in such detectors is critical to understanding the data obtained. The subject of this paper is a Monte Carlo computer code we have developed to simulate the electron cascade in a microchannel plate under a static applied voltage. Also included in the simulation is elastic reflection of low-energy electrons from the channel wall, which is important at lower voltages. When model results were compared to measured microchannel plate sensitivities, good agreement was found. Spatial resolution simulations of MCP-based detectors were also presented and found to agree with experimental measurements.

  19. Silicon Microchannel Plate Large Area UV Detector Project

    Data.gov (United States)

    National Aeronautics and Space Administration — To address the NASA GSFC need for efficient UV photodetectors for NASA missions, such as the follow-on to FUV detectors of the Galaxy Evolution Explorer, Physical...

  20. Design, fabrication and characterisation of InGaAs/InP single-photon avalanche diode detectors

    CERN Document Server

    Warburton, R E; Tan, L; Ng, J S; Krysa, A; Groom, K; David, J P R; Cova, S; Buller, G S; Warburton, Ryan E.; Pellegrini, Sara; Tan, Lionel; Ng, Jo Shien; Krysa, Andrey; Groom, Kris; David, John P.R.; Cova, Sergio; Buller, Gerald S.

    2006-01-01

    This paper demonstrates the performance of planar geometry InGaAs/InP avalanche diodes, specifically designed and fabricated for Geiger-mode operation at wavelengths around 1550nm, in terms of dark count rate, single-photon detection efficiency, afterpulsing and photon-timing jitter.

  1. Therapy imaging: a signal-to-noise analysis of metal plate/film detectors.

    Science.gov (United States)

    Munro, P; Rawlinson, J A; Fenster, A

    1987-01-01

    We have measured the modulation transfer functions [MTF (f)'s] and the noise power spectra [NPS (f)] of therapy x-ray detectors irradiated by 60Co, 6- and 18-MV radiotherapy beams. Using these quantities, we have calculated the noise-equivalent quanta [NEQ (f)] and the detective quantum efficiency [DQE (f)] to quantitate the limitations of therapy detectors. The detectors consisted of film or fluorescent screen-film combinations in contact with copper, lead, or tungsten metal plates. The resolution of the detectors was found to be comparable to fluorescent screen-film combinations used in diagnostic radiology, however, the signal-to-noise ratio [SNR (f)] of the detectors was limited due to film granularity. We conclude that improved images can be obtained by using alternative detector systems which have less noise or film granularity.

  2. Detection efficiency evaluation for a large area neutron sensitive microchannel plate detector

    Science.gov (United States)

    Wang, Yi-ming; Tian, Yang; Yang, Yi-gang; Liu, Ren; Pan, Jing-sheng; Wang, Xue-wu; Zhang, Zhi

    2016-09-01

    In this paper, the detection efficiency of a large area neutron sensitive microchannel plate detector has been evaluated. A 6LiF/ZnS scintillator detector 65 mm in diameter and 0.32 mm in thickness, with product code, EJ426HD2, produced by Eljen Technology, was employed as the benchmark detector. The TOF spectra of these two detectors were simultaneously measured and the energy spectra were then deduced to calculate the detection efficiency curve of the nMCP detector. Tests show the detection efficiency@25.3 meV thermal neutrons is 34% for this nMCP detector. Supported by National Natural Science Foundation of China (11375095, 11175098)

  3. Detailed models for timing and efficiency in resistive plate chambers

    CERN Document Server

    Riegler, Werner

    2003-01-01

    We discuss detailed models for detector physics processes in Resistive Plate Chambers, in particular including the effect of attachment on the avalanche statistics. In addition, we present analytic formulas for average charges and intrinsic RPC time resolution. Using a Monte Carlo simulation including all the steps from primary ionization to the front-end electronics we discuss the dependence of efficiency and time resolution on parameters like primary ionization, avalanche statistics and threshold.

  4. Direct tests of micro channel plates as the active element of a new shower maximum detector

    Energy Technology Data Exchange (ETDEWEB)

    Ronzhin, A., E-mail: ronzhin@fnal.gov [Fermilab, Batavia, IL 60510 (United States); Los, S.; Ramberg, E. [Fermilab, Batavia, IL 60510 (United States); Apresyan, A.; Xie, S.; Spiropulu, M. [California Institute of Technology, Pasadena, CA (United States); Kim, H. [University of Chicago, Chicago, IL 60637 (United States)

    2015-09-21

    We continue the study of micro channel plates (MCP) as the active element of a shower maximum (SM) detector. We present below test beam results obtained with MCPs detecting directly secondary particles of an electromagnetic shower. The MCP efficiency to shower particles is close to 100%. The time resolution obtained for this new type of the SM detector is at the level of 40 ps.

  5. Development of high performance Avalanche Photodiodes and dedicated analog systems for HXI/SGD detectors onboard the Astro-H mission

    Science.gov (United States)

    Saito, T.; Nakamori, T.; Yoshino, M.; Mizoma, H.; Kataoka, J.; Kawakami, K.; Yatsu, Y.; Ohno, M.; Goto, K.; Hanabata, Y.; Takahashi, H.; Fukazawa, Y.; Sasano, M.; Torii, S.; Uchiyama, H.; Nakazawa, K.; Makishima, K.; Watanabe, S.; Kokubun, M.; Takahashi, T.; Mori, K.; Tajima, H.; Astro-H HXI/SGD Team

    2013-01-01

    Hard X-ray Imager and Soft Gamma-ray Detector are being developed as onboard instruments for the Astro-H mission, which is scheduled for launch in 2014. In both detectors, BGO scintillators play key roles in achieving high sensitivity in low Earth orbit (LEO), by generating active veto signals to reject cosmic-ray events and gamma-ray backgrounds from radio-activated detector materials. In order to maximize background rejection power, it is also important to minimize the energy threshold of this shield. As a readout sensor of weak scintillation light from a number of BGO crystals in a complicated detector system, high performance, reverse-type Avalanche Photodiodes (APDs), with an effective area of 10×10 mm2 are being employed, instead of bulky photomultiplier tubes (PMTs).Another advantage of using APDs is their low power consumption, although the relatively low gain of APDs (compared to conventional PMTs) requires dedicated analog circuits for noise suppression. In this paper, we report on the development and performance of APD detectors specifically designed for the Astro-H mission. In addition to APD performance, various environmental tests, including radiation hardness and qualification thermal cycling, will be described in detail. Moreover, a dedicated charge sensitive amplifier and analog filters are newly developed and tested here to optimize the performance of APDs to activate fast veto signals within a few μs from the BGO trigger. We will also report on overall performance testing of a prototype BGO detector system that mimics the data acquisition system onboard Astro-H.

  6. Readout electronics for low dark count pixel detectors based on Geiger mode avalanche photodiodes fabricated in conventional CMOS technologies for future linear colliders

    Energy Technology Data Exchange (ETDEWEB)

    Vilella, E., E-mail: evilella@el.ub.es [Department of Electronics, University of Barcelona (UB), Marti i Franques 1, 08028 Barcelona (Spain); Arbat, A. [Department of Electronics, University of Barcelona (UB), Marti i Franques 1, 08028 Barcelona (Spain); Comerma, A.; Trenado, J. [Department of Structure and Constituents of Matter, University of Barcelona (UB), Marti i Franques 1, 08028 Barcelona (Spain); Alonso, O. [Department of Electronics, University of Barcelona (UB), Marti i Franques 1, 08028 Barcelona (Spain); Gascon, D. [Department of Structure and Constituents of Matter, University of Barcelona (UB), Marti i Franques 1, 08028 Barcelona (Spain); Vila, A. [Department of Electronics, University of Barcelona (UB), Marti i Franques 1, 08028 Barcelona (Spain); Garrido, L. [Department of Structure and Constituents of Matter, University of Barcelona (UB), Marti i Franques 1, 08028 Barcelona (Spain); Dieguez, A. [Department of Electronics, University of Barcelona (UB), Marti i Franques 1, 08028 Barcelona (Spain)

    2011-09-11

    High sensitivity and excellent timing accuracy of the Geiger mode avalanche photodiodes make them ideal sensors as pixel detectors for particle tracking in high energy physics experiments to be performed in future linear colliders. Nevertheless, it is well known that these sensors suffer from dark counts and afterpulsing noise, which induce false hits (indistinguishable from event detection) as well as an increase in the necessary area of the readout system. In this work, we present a comparison between APDs fabricated in a high voltage 0.35 {mu}m and a high integration 0.13 {mu}m commercially available CMOS technologies that has been performed to determine which of them best fits the particle collider requirements. In addition, a readout circuit that allows low noise operation is introduced. Experimental characterization of the proposed pixel is also presented in this work.

  7. Integrated avalanche photodiode arrays

    Science.gov (United States)

    Harmon, Eric S.

    2015-07-07

    The present disclosure includes devices for detecting photons, including avalanche photon detectors, arrays of such detectors, and circuits including such arrays. In some aspects, the detectors and arrays include a virtual beveled edge mesa structure surrounded by resistive material damaged by ion implantation and having side wall profiles that taper inwardly towards the top of the mesa structures, or towards the direction from which the ion implantation occurred. Other aspects are directed to masking and multiple implantation and/or annealing steps. Furthermore, methods for fabricating and using such devices, circuits and arrays are disclosed.

  8. Fast scintillation timing detector using proportional-mode avalanche photodiode for nuclear resonant scattering experiments in high-energy synchrotron X-ray region

    Science.gov (United States)

    Inoue, Keisuke; Kishimoto, Shunji

    2016-01-01

    To obtain both a high count rate of >107 s-1 and a detection efficiency sufficient for high-energy X-rays of >30 keV, we propose a scintillation timing detector using a proportional-mode silicon avalanche photodiode (Si-APD) for synchrotron radiation nuclear resonant scattering. We here present results obtained with a prototype detector using a lead-loaded plastic scintillator (EJ-256) mounted on a proportional-mode Si-APD (active area size: 3 mm in diameter). The detector was operated at ‒35 °C for a better signal-to-noise ratio. Using synchrotron X-rays of 67.41 keV, which is the same energy as the first excited level of 61Ni, we successfully measured pulse-height and time spectra of the scintillation light. A good time resolution of 0.50±0.06 ns (full width at half-maximum) was obtained for 67.41 keV X-rays with a scintillator 3 mm in diameter and 2 mm thick.

  9. High resolution, two-dimensional imaging, microchannel plate detector for use on a sounding rocket experiment

    Science.gov (United States)

    Bush, Brett C.; Cotton, Daniel M.; Siegmund, Oswald H.; Chakrabarti, Supriya; Harris, Walter; Clarke, John

    1991-01-01

    We discuss a high resolution microchannel plate (MCP) imaging detector to be used in measurements of Doppler-shifted hydrogen Lyman-alpha line emission from Jupiter and the interplanetary medium. The detector is housed in a vacuum-tight stainless steel cylinder (to provide shielding from magnetic fields) with a MgF2 window. Operating at nominal voltage, the four plate configuration provides a gain of 1.2 x 10 exp 7 electrons per incident photon. The wedge-and-strip anode has two-dimensional imaging capabilities, with a resolution of 40 microns FWHM over a one centimeter diameter area. The detector has a high quantum efficiency while retaining a low background rate. A KBr photocathode is used to enhance the quantum efficiency of the bare MCPs to a value of 35 percent at Lyman-alpha.

  10. Effects of variation of environmental parameters on the performance of Resistive Plate Chamber detectors

    Energy Technology Data Exchange (ETDEWEB)

    Meghna, K.K. [INO Graduate Training Programme and Saha Institute of Nuclear Physics, Kolkata 700064 (India); Homi Bhabha National Institute, Mumbai 400085 (India); Biswas, S. [School of Physical Sciences, National Institute of Science Education and Research, Bhubaneswar 751005 (India); Jash, A. [INO Graduate Training Programme and Saha Institute of Nuclear Physics, Kolkata 700064 (India); Homi Bhabha National Institute, Mumbai 400085 (India); Chattopadhyay, S. [Variable Energy Cyclotron Centre, Kolkata 700064 (India); Homi Bhabha National Institute, Mumbai 400085 (India); Saha, S., E-mail: satyajit.saha@saha.ac.in [Applied Nuclear Physics Division, Saha Institute of Nuclear Physics, Kolkata 700064 (India); Homi Bhabha National Institute, Mumbai 400085 (India)

    2016-04-21

    Performance of single gap Resistive Plate Chamber (RPC) detectors is investigated under variation of environmental parameters, such as temperature and relative humidity. Operational characteristics of the RPCs depend on both the environmental temperature and the relative humidity. Sensitivity to such dependence is found to be more on temperature rather than the relative humidity. Qualitative interpretation of some of the results obtained is given based on the known properties of the electrode materials and gases used in the detectors. - Highlights: • Performance of single gap bakelite Resistive Plate Chamber (RPC) detectors is investigated under independent variation of environmental temperature and relative humidity. • Parameters such as leakage currents, noise rates, efficiency and timing characteristics of RPCs are investigated. • Operational characteristics of the RPCs depend on both the environmental temperature and the relative humidity. • Sensitivity of the operational parameters to variation of environmental parameters is found to be more on temperature rather than the relative humidity.

  11. New Developments in the Position Sensitive Detectors Based on Microchannel Plates

    Science.gov (United States)

    Tremsin, A. S.; Siegmund, O. H. W.

    2002-11-01

    We report on the latest developments in position sensitive photon counting detectors based on microchannel plates. Substantial improvement of the spatial resolution was achieved with introduction of new readout technology, namely crossed strip (XS) anode, and corresponding processing electronics. The spatial resolution of XS readout appeared to be as small as ~3-4 μm FWHM. Reduction of the total detector gain (down to 106 and potentially lower) without compromising the spatial accuracy allows detector operation at much higher local and global counting rates since the microchannel recharge time becomes smaller. Recent developments of novel microchannel plate technologies provide basis for substantial increase of the spectral sensitivity and quantum efficiency of MCP detectors. We have tested a number of new Silicon micromachined MCPs The new MCP technologies should allow deposition of completely new photocathode materials directly on the front surface of microchannel plates (opaque photocathodes). Opposite to standard glass MCPs new Silicon MCPs can sustain high temperatures (-800 C°) required for the photocathode deposition and activation processes.

  12. Miniaturized time-resolved Raman spectrometer for planetary science based on a fast single photon avalanche diode detector array.

    Science.gov (United States)

    Blacksberg, Jordana; Alerstam, Erik; Maruyama, Yuki; Cochrane, Corey J; Rossman, George R

    2016-02-01

    We present recent developments in time-resolved Raman spectroscopy instrumentation and measurement techniques for in situ planetary surface exploration, leading to improved performance and identification of minerals and organics. The time-resolved Raman spectrometer uses a 532 nm pulsed microchip laser source synchronized with a single photon avalanche diode array to achieve sub-nanosecond time resolution. This instrument can detect Raman spectral signatures from a wide variety of minerals and organics relevant to planetary science while eliminating pervasive background interference caused by fluorescence. We present an overview of the instrument design and operation and demonstrate high signal-to-noise ratio Raman spectra for several relevant samples of sulfates, clays, and polycyclic aromatic hydrocarbons. Finally, we present an instrument design suitable for operation on a rover or lander and discuss future directions that promise great advancement in capability.

  13. The multigap resistive plate chamber as a time-of-flight detector

    CERN Document Server

    Akindinov, A; Basile, M; Cerron-Zeballos, E; Cifarelli, Luisa; Cindolo, F; Choi, J; Cozzoni, B; De Caro, A; De Pasquale, S; Kim, D W; Kim, N Y; Klempt, W; Kluge, A; Laurenti, G; Lee, S C; Golovine, V; Hatzifotiadou, D; Martemyanov, A N; Martinengo, P; Pesci, A; Platner, E D; Roberts, J; Seganti, A; Semak, A A; Smirnitsky, A V; Spegel, M; Szymanski, P; Valenti, G; Vicinanza, D; Williams, M C S; Zichichi, A

    2000-01-01

    The goal of this R&D has been to reach the time resolution needed for time-of-flight detectors using the Multigap Resistive Plate Chamber (MRPC). We present here a MRPC with a time resolution of 70 ps. This prototype has been studied within the R&D program for the very large area TOF array of the ALICE experiment at the CERN LHC. (5 refs).

  14. Fluorescence-suppressed time-resolved Raman spectroscopy of pharmaceuticals using complementary metal-oxide semiconductor (CMOS) single-photon avalanche diode (SPAD) detector.

    Science.gov (United States)

    Rojalin, Tatu; Kurki, Lauri; Laaksonen, Timo; Viitala, Tapani; Kostamovaara, Juha; Gordon, Keith C; Galvis, Leonardo; Wachsmann-Hogiu, Sebastian; Strachan, Clare J; Yliperttula, Marjo

    2016-01-01

    In this work, we utilize a short-wavelength, 532-nm picosecond pulsed laser coupled with a time-gated complementary metal-oxide semiconductor (CMOS) single-photon avalanche diode (SPAD) detector to acquire Raman spectra of several drugs of interest. With this approach, we are able to reveal previously unseen Raman features and suppress the fluorescence background of these drugs. Compared to traditional Raman setups, the present time-resolved technique has two major improvements. First, it is possible to overcome the strong fluorescence background that usually interferes with the much weaker Raman spectra. Second, using the high photon energy excitation light source, we are able to generate a stronger Raman signal compared to traditional instruments. In addition, observations in the time domain can be performed, thus enabling new capabilities in the field of Raman and fluorescence spectroscopy. With this system, we demonstrate for the first time the possibility of recording fluorescence-suppressed Raman spectra of solid, amorphous and crystalline, and non-photoluminescent and photoluminescent drugs such as caffeine, ranitidine hydrochloride, and indomethacin (amorphous and crystalline forms). The raw data acquired by utilizing only the picosecond pulsed laser and a CMOS SPAD detector could be used for identifying the compounds directly without any data processing. Moreover, to validate the accuracy of this time-resolved technique, we present density functional theory (DFT) calculations for a widely used gastric acid inhibitor, ranitidine hydrochloride. The obtained time-resolved Raman peaks were identified based on the calculations and existing literature. Raman spectra using non-time-resolved setups with continuous-wave 785- and 532-nm excitation lasers were used as reference data. Overall, this demonstration of time-resolved Raman and fluorescence measurements with a CMOS SPAD detector shows promise in diverse areas, including fundamental chemical research, the

  15. Front-End electronics development for the new Resistive Plate Chamber detector of HADES

    Science.gov (United States)

    Gil, A.; Belver, D.; Cabanelas, P.; Díaz, J.; Garzón, J. A.; González-Díaz, D.; Koenig, W.; Lange, J. S.; Marín, J.; Montes, N.; Skott, P.; Traxler, M.

    2007-11-01

    In this paper we present the new RPC wall, which is being installed in the HADES detector at Darmstadt GSI. It consists of time-of-flight (TOF) detectors used for both particle identification and triggering. Resistive Plate Chamber (RPC) detectors are becoming widely used because of their excellent TOF capabilities and reduced cost. The wall will contain 1024 RPC modules, covering an active area of around 7 m2, replacing the old TOFino detector at the low polar angle region. The excellent TOF and good charge resolutions of the new detector will improve the time resolution to values better than 100 ps. The Front-End electronics for the readout of the RPC signals is implemented with two types of boards to satisfy the space constraints: the Daughterboards are small boards that amplify the low level signals from the detector and provide fast discriminators for time of flight measurements, as well as an integrator for charge measurements. The Motherboard provides stable DC voltages and a stable ground, threshold DACs for the discriminators, multiplicity trigger and impedance matched paths for transfer of time window signals that contain information about time and charge. These signals are sent to a custom TDC board that label each event and send data through Ethernet to be conveniently stored.

  16. Novel large format sealed tube microchannel plate detectors for Cherenkov timing and imaging

    Energy Technology Data Exchange (ETDEWEB)

    Siegmund, O.H.W., E-mail: ossy@ssl.berkeley.ed [Experimental Astrophysics Group, Space Sciences Laboratory, 7 Gauss Way, University of California, Berkeley, CA 94720 (United States); McPhate, J.B.; Vallerga, J.V.; Tremsin, A.S.; Jelinsky, S.R. [Experimental Astrophysics Group, Space Sciences Laboratory, 7 Gauss Way, University of California, Berkeley, CA 94720 (United States); Frisch, H.J. [Enrico Fermi Institute, 5640 S. Ellis Avenue, University of Chicago, Chicago, IL 60637 (United States)

    2011-05-21

    Large area (20x20 cm{sup 2}) sealed tube detectors using novel borosilicate glass microchannel plates, with bialkali photocathodes and strip-line readouts are being developed for Cherenkov light detection. Designs based on conventional sealed tubes with alumina brazed body construction and hot indium seals have been developed. Borosilicate glass substrates with 20 and 40 {mu}m holes have been processed using atomic layer deposition to produce functional microchannel plates. Initial results for these in a 33 mm format show gain, imaging performance, pulse shape and lifetime characteristics that are similar to standard glass microchannel plates. Large area (20x20 cm{sup 2}) borosilicate glass substrates with 20 {mu}m pores have also been made.

  17. High-speed microstrip multi-anode multichannel plate detector system

    Science.gov (United States)

    Riedo, Andreas; Tulej, Marek; Rohner, Urs; Wurz, Peter

    2017-04-01

    High-speed detector systems with high dynamic range and pulse width characteristics in the sub-nanosecond regime are mandatory for high resolution and highly sensitive time-of-flight mass spectrometers. Typically, for a reasonable detector area, an impedance-matched anode design is necessary to transmit the registered signal fast and distortion-free from the anode to the signal acquisition system. In this report, a high-speed microstrip multi-anode multichannel plate detector is presented and discussed. The anode consists of four separate active concentric anode segments allowing a simultaneous readout of signal with a dynamic range of about eight orders of magnitude. The impedance matched anode segments show pulse width of about 250 ps, measured at full width at half maximum, and rise time of ˜170 ps, measured with an oscilloscope with a sampling rate of 20 GS/s and 4 GHz analogue bandwidth. The usage of multichannel plates as signal amplifier allowed the design of a lightweight, low power consuming, and compact detector system, suitable, e.g., for the integration into space instrumentation or portable systems where size, weight, and power consumption are limited parameters.

  18. Design of a new vacuum Compton gamma-ray detector with clad metal electron-converter plate

    Institute of Scientific and Technical Information of China (English)

    Han Hetong; Wang Qunshu; Xia Liangbin; Guan Xingyin; Tan Xinjian; Zhang Zichuan

    2009-01-01

    A newly designed vacuum Compton gamma-ray detector with Ta-Al clad-metal electron converter plate is de-scribed. The detecting efficiency for 1.25 MeV gamma-ray is 7.85×10-3 electron/γ, which is 2.5 times higher than that with Fe converter plate. The designed detector has the merits of well processed and static vacuum keeping and can be used for intense pulsed gamma ray detecting.

  19. HV Test of the CTS Edgeless Silicon Detector in Vacuum and Close to a Grounded Plate

    CERN Document Server

    Eremin, Vladimir; Ruggiero, Gennaro

    2007-01-01

    The TOTEM Roman Pot Silicon sensors will be operated in vacuum to minimise the mechanical stress of the thin metal window which separates the detector package from the ultra high vacuum of the beam. To approach the beam axis as close as possible the detectors will be mounted with their edge at a distance of the order 100 - 200 um from the thin metal window. As the detectors will be run in overdepletion mode to allow the full charge collection within the shaping time of the readout electronics, there will be a potential drop of more than 100 V across their edge. Moreover this potential drop might need to be further increased with the accumulated radiation dose. The main goals of the tests described in this note are: - Characterisation of the voltage-current characteristics when the detector edge is in the direct vicinity of a grounded metal plate which simulates the above mentioned vacuum window; - Demonstration of the detector operation in vacuum at different pressures.

  20. A 200 cm x 50 cm large multigap resistive plate chamber based neutron detector

    Energy Technology Data Exchange (ETDEWEB)

    Yakorev, Dmitry; Elekes, Zoltan; Bemmerer, Daniel; Kempe, Mathias; Sobiella, Manfred; Stach, Daniel; Wagner, Andreas [Helmholtz-Zentrum Dresden-Rossendorf (HZDR), Dresden (Germany); Roeder, Marko; Zuber, Kai [TU Dresden (Germany); Cowan, Thomas [Helmholtz-Zentrum Dresden-Rossendorf (HZDR), Dresden (Germany); TU Dresden (Germany)

    2012-07-01

    A prototype for a multigap resistive plate chamber (MRPC) based detector of 200 cm x 50 cm size for 1 GeV neutrons has been developed, built and tested. The principle of operation is the conversion of the high-energy neutron to a charged particle in an iron converter, and the detection of the charged particle in the MRPC. Experiments using the single-electron mode of operation of the ELBE 40 MeV electron accelerator showed that a time resolution of {sigma}{sub t}<100 ps was reached for minimum-ionizing particles, at nearly full efficiency. Extensive simulations show that it is feasible to construct a time-of-flight detector for GeV neutrons based on such a principle.

  1. Direct tests of a pixelated microchannel plate as the active element of a shower maximum detector

    Science.gov (United States)

    Apresyan, A.; Los, S.; Pena, C.; Presutti, F.; Ronzhin, A.; Spiropulu, M.; Xie, S.

    2016-08-01

    One possibility to make a fast and radiation resistant shower maximum detector is to use a secondary emitter as an active element. We report our studies of microchannel plate photomultipliers (MCPs) as the active element of a shower-maximum detector. We present test beam results obtained using Photonis XP85011 to detect secondary particles of an electromagnetic shower. We focus on the use of the multiple pixels on the Photonis MCP in order to find a transverse two-dimensional shower distribution. A spatial resolution of 0.8 mm was obtained with an 8 GeV electron beam. A method for measuring the arrival time resolution for electromagnetic showers is presented, and we show that time resolution better than 40 ps can be achieved.

  2. Direct tests of a pixelated microchannel plate as the active element of a shower maximum detector

    Energy Technology Data Exchange (ETDEWEB)

    Apresyan, A. [California Institute of Technology, Pasadena, CA (United States); Los, S. [Fermi National Accelerator Laboratory, Batavia, IL (United States); Pena, C.; Presutti, F. [California Institute of Technology, Pasadena, CA (United States); Ronzhin, A. [Fermi National Accelerator Laboratory, Batavia, IL (United States); Spiropulu, M.; Xie, S. [California Institute of Technology, Pasadena, CA (United States)

    2016-08-21

    One possibility to make a fast and radiation resistant shower maximum detector is to use a secondary emitter as an active element. We report our studies of microchannel plate photomultipliers (MCPs) as the active element of a shower-maximum detector. We present test beam results obtained using Photonis XP85011 to detect secondary particles of an electromagnetic shower. We focus on the use of the multiple pixels on the Photonis MCP in order to find a transverse two-dimensional shower distribution. A spatial resolution of 0.8 mm was obtained with an 8 GeV electron beam. A method for measuring the arrival time resolution for electromagnetic showers is presented, and we show that time resolution better than 40 ps can be achieved.

  3. Using pulse shape analysis to improve the position resolution of a resistive anode microchannel plate detector

    CERN Document Server

    Siwal, Davinder; deSouza, R T

    2015-01-01

    Digital signal processing techniques were employed to investigate the joint use of charge division and risetime analyses for the resistive anode (RA) coupled to a microchannel plate detector (MCP). In contrast to the typical approach of using the relative charge at each corner of the RA, this joint approach results in a significantly improved position resolution. A conventional charge division analysis utilizing analog signal processing provides a position measured resolution of 170 $\\mu$m (FWHM). By using the correlation between risetime and position we were able to obtain a measured resolution of 92 $\\mu$m (FWHM), corresponding to an intrinsic resolution of 64 $\\mu$m (FMHM) for a single Z-stack MCP detector.

  4. Aging Avalanches

    Science.gov (United States)

    Boettcher, Stefan; Paczuski, Maya

    1997-03-01

    We have shown that in an analytically solvable model of Self-Organized Criticality (SOC)(S. Boettcher & M. Paczuski, Phys. Rev. Lett. 76), 348 (1996). the evolving avalanche is governed by an equation of motion with a memory term that ranges over all past events.(S. Boettcher & M. Paczuski, Phys. Rev. E 54), 1082 (1996). The solution for the propagator shows sub-diffusive behavior with a broad exponential tail. Numerical studies of the temporal correlations during avalanches in a variety of SOC systems indicate that history dependence and hierarchical structures are generic features which emerge dynamically from simple local update rules. In particular, we find(S. Boettcher & M. Paczuski, ``Off-Equilibrium Behavior and Aging in Self-Organized Criticality'', (in preparation).) ``aging'' similar to the slow relaxation behavior in disordered systems that move through ``rugged landscapes'' in phase space, such as spin glasses.

  5. The Resistive-Plate WELL with Argon mixtures - a robust gaseous radiation detector

    CERN Document Server

    Moleri, L; Arazi, L; Rocha Azevedo, Carlos Davide; Oliveri, E; Pitt, M; Schaarschmidt, J; Shaked-Renous, D; Marques Ferreira dos Santos, J; Veloso, Joao Filipe Calapez de Albuquerque; Breskin, A; Bressler, S

    2016-01-01

    A thin single-element THGEM-based, Resistive-Plate WELL (RPWELL) detector was operated with 150 GeV/c muon and pion beams in Ne/(5%CH$_4$), Ar/(5%CH$_4$) and Ar/(7%CO$_2$); signals were recorded with 1 cm$^2$ square pads and SRS/APV25 electronics. Detection efficiency values greater than 98% were reached in all the gas mixtures, at average pad multiplicity of 1.2. The use of the 10$^9${\\Omega}cm resistive plate resulted in a completely discharge-free operation also in intense pion beams. The efficiency remained essentially constant at 98-99% up to fluxes of $\\sim$10$^4$Hz/cm$^2$, dropping by a few % when approaching 10$^5$ Hz/cm$^2$. These results pave the way towards cost-effective, robust, efficient, large-scale detectors for a variety of applications in future particle, astro-particle and applied fields. A potential target application is digital hadron calorimetry.

  6. Calculating and optimizing inter-electrode capacitances of charge division microchannel plate detectors

    Energy Technology Data Exchange (ETDEWEB)

    Xing, Yan [Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun 130033 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Chen, Bo, E-mail: chenb@ciomp.ac.cn [Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun 130033 (China); Zhang, Hong-Ji; Wang, Hai-Feng; He, Ling-Ping [Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun 130033 (China); Jin, Fang-Yuan [Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, Changchun 130033 (China); University of Chinese Academy of Sciences, Beijing 100049 (China)

    2016-04-01

    Based on the principle of charge division microchannel plate detectors, the inter-electrode capacitances of charge division anodes which are related to electronic noise of the charge sensitive amplifier and crosstalk effect of the anode are presented. Under all the requirements of charge division microchannel plate detectors such as the imaging linearity and spatial resolution, decreasing the inter-electrode capacitances is one way to improve the imaging performance. In this paper, we illustrate the simulation process of calculating the inter-electrode capacitances. Moreover, a Wedge and Strip (WSZ) anode is fabricated with the picosecond laser micromachining process. Comparing the simulated capacitances and measured capacitances, the three-dimensional finite element method is proved to be valid. Furthermore, by adjusting the design parameters of the anode, the effects of the substrate permittivity, insulation width and the size of pitch on the inter-electrode capacitances have been analysed. The structure of the charge division anode has been optimized based on the simulation data.

  7. High Spatial Resolution Investigations of Microchannel Plate Imaging Properties for UV Detectors

    Science.gov (United States)

    Siegmund, Oswald

    1996-01-01

    Microchannel plate (MCP) photon counting detectors are currently being used with great success on many of the recent NASA/ESA ultraviolet (UV) astrophysics missions that make observations in the 1OO A - 1600 A range. These include HUT, the Wide Field Camera on ROSAT, EUVE, ALEXIS, ORFEUS, and SOHO. These devices have also been chosen to fly on future UV astrophysics missions such as FUSE, FUVITA, IMAGE, and both the HST STIS and Advanced Camera instruments. During the period of this award we have fabricated a dual-chamber vacuum test facility to carry out laboratory testing of detector resolution, image stability and linearity, and flat field performance to enable us to characterize the performance of MCPs and their associated read-out architectures. We have also fabricated and tested a laboratory 'test-bed' delay line detector, which can accommodate MCP's with a wide range of formats and run at high data rates, to continue our studies of MCP image fixed pattern noise, and particularly for new small pore MCP's which have recently come onto the market. These tests were mainly focussed on the assessment of cross delay-line (XDL) and double delay line (DDL) anode read-out schemes, with particular attention being focussed on flat-field and spatial resolution performance.

  8. [Avalanche accidents and treatment of avalanche victims].

    Science.gov (United States)

    Skaiaa, Sven Christjar; Thomassen, Øyvind

    2016-03-15

    Avalanches may be provoked spontaneously or as a result of human activity, and they trigger the need for considerable rescue resources. Avalanche search and rescue operations are complex and characterised by physical and mental stress. The guidelines for resuscitation of avalanche victims may be perceived as complex and abstruse, which can lead to suboptimal treatment and an increased strain on rescue teams. The purpose of this article is to summarise the principles for medical treatment of avalanche victims.

  9. Study of timing response and charge spectra of glass based Resistive Plate Chamber detectors for INO-ICAL experiment

    Science.gov (United States)

    Gaur, A.; Kumar, A.; Naimuddin, Md.

    2017-03-01

    Resistive Plate chambers (RPCs) are robust and affordable gaseous detectors that combine low cost with excellent timing, good spatial resolution and fast response to the incoming particles. The India Based Neutrino Observatory is an approved project aimed at building a magnetised Iron Calorimeter (ICAL) detector to study Neutrino physics and related issues. The ICAL experiment will utilize about 29000 RPC's as active detector elements, sandwiched between alternate plates of thick iron. The RPC detectors will be used to detect muons produced from the atmospheric neutrinos interaction with an iron target. The spatial information of the muons will be extracted from the two dimensional readout and the hit position in the respective layers. The up going and down going directionality will be obtained using the time stamp of hits in the active detectors. The charge induced by the particle and its behaviour with respect to the applied voltage play a significant role in designing the readout electronics for the detector. In this paper, we present the timing and charge measurement of single gap glass based RPC detectors. We will also report about studies on the dependence of the timing and charge response of these RPC detectors as a function of the gas composition.

  10. Cross strip anode readouts for microchannel plate detectors: developing flight qualified prototypes

    Science.gov (United States)

    Vallerga, John; Cooney, M.; Raffanti, R.; Varner, G.; Siegmund, O.; McPhate, J. B.; Tremsin, A.

    2014-01-01

    Photon counting microchannel plate (MCP) imagers have been the detector of choice for most UV astronomical missions over the last two decades (eg. EUVE, FUSE, COS on Hubble etc.). Over this duration, improvements in the MCP laboratory readout technology have resulted in better spatial resolution (x10), temporal resolution (x 1000) and output event rate (x100), all the while operating at lower gain (x 10) resulting in lower high voltage requirements and longer MCP lifetimes. One such technology is the parallel cross strip (PXS) readout. The PXS anode is a set of orthogonal conducting strips (80 x 80), typically spaced at a 635 micron pitch onto which charge clouds from MCP amplified events land. Each strip has its own charge sensitive amplifier that is sampled continuously by a dedicated analog to digital (ADC) converter at 50MHz. All of the 160 ADC digital output lines are fed into a field programmable gate array (FGPA) which can detect charge events landing on the strips, measure the peak amplitudes of those charge events and calculate their spatial centroid along with their time of arrival (X,Y,T). Laboratory versions of these electronics have demonstrated count rates on the order of 2 MHz, and temporal resolution of ~ 1ns. In 2012 the our group at U.C. Berkeley, along with our partners at the U. Hawaii, received a Strategic Astrophysics Technology grant to raise the TRL of the PXS detector from 4 to 6 by replacing most of the 19" rack mounted, high powered electronics with application specific integrated circuits (ASICs) which will lower the power, mass and volume requirements of the PXS detector. We were also tasked to design and fabricate a "standard" 50mm square active area MCP detector incorporating these electronics that can be environmentally qualified for flight (temperature, vacuum, vibration). This detector design could then be modified for individual flight opportunities with a higher level of confidence than starting from scratch. We will present the

  11. Characterizing Atacama B-mode Search Detectors with a Half-Wave Plate

    Science.gov (United States)

    Simon, S. M.; Appel, J. W.; Campusano, L. E.; Choi, S. K.; Crowley, K. T.; Essinger-Hileman, T.; Gallardo, P.; Ho, S. P.; Kusaka, A.; Nati, F.; Palma, G. A.; Page, L. A.; Raghunathan, S.; Staggs, S. T.

    2016-08-01

    The Atacama B-Mode Search (ABS) instrument is a cryogenic (˜ 10 K) crossed-Dragone telescope located at an elevation of 5190 m in the Atacama Desert in Chile that observed for three seasons between February 2012 and October 2014. ABS observed the cosmic microwave background (CMB) at large angular scales (40ABS focal plane consists of 480 transition-edge sensor (TES) bolometers. They are coupled to orthogonal polarizations from a planar ortho-mode transducer and observe at 145 GHz. ABS employs an ambient-temperature, rapidly rotating half-wave plate (HWP) to mitigate systematic effects and move the signal band away from atmospheric 1 / f noise, allowing for the recovery of large angular scales. We discuss how the signal at the second harmonic of the HWP rotation frequency can be used for data selection and for monitoring the detector responsivities.

  12. Testing micro-channel plate detectors for the particle identification upgrade of LHCb

    CERN Document Server

    Castillo Garcia, L

    2012-01-01

    The TORCH, Time of internally Reflected Cherenkov Light, is proposed for the high luminosity upgrade of the LHCb experiment. The detector combines Time-of-Flight and Cherenkov techniques to achieve positive pi/K/p separation on a >= 3 sigma level in the momentum range below 10 GeV/c. The required time resolution is <= 50 ps for single photon signal. In a preliminary R\\&D phase, we have shown that already commercially available micro-channel plate tubes with 8 x 8 channels fulfil the requirements. Timing properties of the tubes have been investigated with a pulsed laser diode in single photon regime. Key results from these laboratory tests are reported. An excellent timing resolution of <40 ps is achieved with an efficiency of similar to 90\\%. (C) 2011 Elsevier B.V. All rights reserved.

  13. A fast microchannel plate-scintillator detector for velocity map imaging and imaging mass spectrometry.

    Science.gov (United States)

    Winter, B; King, S J; Brouard, M; Vallance, C

    2014-02-01

    The time resolution achievable using standard position-sensitive ion detectors, consisting of a chevron pair of microchannel plates coupled to a phosphor screen, is primarily limited by the emission lifetime of the phosphor, around 70 ns for the most commonly used P47 phosphor. We demonstrate that poly-para-phenylene laser dyes may be employed extremely effectively as scintillators, exhibiting higher brightness and much shorter decay lifetimes than P47. We provide an extensive characterisation of the properties of such scintillators, with a particular emphasis on applications in velocity-map imaging and microscope-mode imaging mass spectrometry. The most promising of the new scintillators exhibits an electron-to-photon conversion efficiency double that of P47, with an emission lifetime an order of magnitude shorter. The new scintillator screens are vacuum stable and show no signs of signal degradation even over longer periods of operation.

  14. Field Decay and Snapback Measurements using a Fast Hall Plate Detector

    CERN Document Server

    Benedico, E; Haverkamp, M; ten Haken, B; ten Kate, H H J; Sanfilippo, S

    2002-01-01

    In superconducting particle accelerators significant changes occur in tune and chromaticity during the injection of particles and their subsequent acceleration. This behavior is caused by the decay of magnetic field components in the superconducting accelerator magnets during injection and their so-called "snapback" to the original hysteresis curve during the first few seconds after the start of the energy ramp. The two effects are closely related to a spatially periodic modulation of all field components along the magnet axis. In order to avoid a loss of particles the sextupole component in the dipoles has to be compensated with a very high accuracy. Standard magnetic measurements using rotating coils do not have the time resolution required to completely resolve the snapback. For this reason we have developed a fast system for sextupole measurements consisting of three Hall plates mounted on a ring. A new calibration procedure for the first time allows quantitative results. The detector is used to measure d...

  15. Development of TOF-PET detectors based on the Multi-Gap Resistive Plate Chambers

    Science.gov (United States)

    Amaldi, U.; Borghi, G.; Bucciantonio, M.; Kieffer, R.; Samarati, J.; Sauli, F.; Watts, D.

    2015-04-01

    We describe the development, construction and preliminary results obtained with medium-size Multi-Gap Resistive Plate Chambers prototypes designed to detect and localize 511 keV photons for Positron Emission Tomography imaging applications. The devices are intended for in-beam monitoring of the treatment plans throughout deep tumor therapy with hadron beams; emphasis is put on achieving coincidence time resolutions of few hundred ps, in order to exploit optimized reconstruction algorithm and reduce the heavy non-correlated background contributions distinctive of this operation. Using technologies developed for high energy physics experiments, the detectors can be built for covering large areas, thus leading the way to the conception of full-body PET systems at low cost.

  16. Development of Micro-Pattern Gas Detectors Technologies

    CERN Multimedia

    Richer, J; Santos, D; Barsuk, S; Hamar, G; Shah, M K; Catanesi, M G; Colaleo, A; Maggi, M; Loddo, F; Berardi, V; Bagliesi, M; Menon, G; Richter, R; Lahonde-hamdoun, C; Dris, M; Chechik, R; Ochi, A; Hartjes, F; Lopes, I M; Deshpande, A; Franz, A; Dabrowski, W; Fiutowski, T A; Ferreira, A; Bastos de oliveira, C A; Miller, B W; Monrabal-capilla, F; Liubarsky, I; Plazas de pinzon, M C; Tsarfati, T; Voss, B J R; Carmona martinez, J M; Stocchi, A; Dinu, N; Semeniouk, I; Giebels, B; Marton, K; De leo, R; De lucia, E; Alviggi, M; Bellerive, A; Herten, L G; Zimmermann, S U; Derre, J; Giomataris, I; Peyaud, A; Schune, P; Delagnes, E; Delbart, A; Charles, G; Wang, W; Markou, A; Arazi, L; Cibinetto, G; Edo, Y; Neves, F F; Solovov, V; Stoll, S; Sampsonidis, D; Mindur, B; Zielinska, A Z; Sauli, F; Calapez de albuquerque veloso, J F; Kahlaoui, N; Sharma, A; Bilevych, Y; Zenker, K; Cebrian guajardo, S V; Luzon marco, G M; Dalmaz, A E; Geffroy, N A; Guillaudin, O J H; Cornebise, P; Lounis, A; Bruel, P J; Laszlo, A; Mukerjee, K; Nappi, E; Nuzzo, S V; Bencivenni, G; Tessarotto, F; Levorato, S; Dixit, M S; Riallot, M; Jeanneau, F; Nizery, F G; Maltezos, S; Kyriakis, A; Lyashenko, A; Van der graaf, H; Ferreira marques, R; Alexa, C; Liyanage, N; Dehmelt, K; Hemmick, T K; Polychronakos, V; Cisbani, E; Garibaldi, F; Koperny, S Z; Mora mas, F; Das neves dias carramate, L F; Munoz-vidal, J; Gutierrez, R; Van stenis, M; Resnati, F; Lupberger, M; Desch, K K; Soyk, D; Adloff, C J; Chefdeville, M; Vouters, G; Ranieri, A; Lami, S; Shekhtman, L; Dolgov, A; Bamberger, A; Landgraf, U; Kortner, O; Ferrero, A; Attie, D M; Bakas, G; Tsigaridas, S; Surrow, B; Gnanvo, K A K; Feege, N M; Woody, C L; Bhattacharya, S; Capogni, M; Hohlmann, M; Veenhof, R J; Tapan, I; Dangendorf, V; Monteiro bernades, C M; Castro serrato, H F; De oliveira, R; Ropelewski, L; Behnke, T; Peltier, F; Boudry, V; Radicioni, E; Lai, A; Shemyakina, E; Giganon, A E; Titov, M; Aune, S; Galan lacarra, J A; Papakrivopoulos, I; Komai, H; Van bakel, N A; Tchepel, V; Repond, J O; Li, Y; Kourkoumelis, C; Tzamarias, S; Majumdar, N; Kowalski, T; Da rocha azevedo, C D; Sorel, M; Serra diaz cano, L; Alvarez puerta, V; Trabelsi, A; Riegler, W; Ketzer, B F; Rosemann, C G; Herrera munoz, D C; Drancourt, C; Mayet, F; Geerebaert, Y; Fodor, Z P; De robertis, G; Felici, G; Scribano memoria, A; Cecchi, R; Dalla torre, S; Gregori, M; Buzulutskov, A; Schwegler, P; Sanchez nieto, F J; Colas, P M A; Gros, M; Neyret, D; Zito, M; Ferrer ribas, E; Breskin, A; Martoiu, V S; Purschke, M L; Loomba, D; Gasik, P J; Petridou, C; Kordas, K; Mukhopadhyay, S; Bucciantonio, M; Bhopatkar, V S; Biagi, S F; Ji, X; Kanaki, K; Zavazieva, D; Capeans garrido, M D M; Schindler, H; Kaminski, J; Krautscheid, T; Lippmann, C; Arora, R; Dafni, T; Garcia irastorza, I; Puill, V; Wicek, F B; Burmistrov, L; Singh, K P; Pugliese, G; Kroha, H; Kunne, F; Alexopoulos, T; Daskalakis, G; Geralis, T; Bettoni, D; Heijhoff, K; Xiao, Z; Tzanakos, G; Leisos, A; Frullani, S; Toledo alarcon, J F; Sahin, O; Kalkan, Y; Giboni, K; Krieger, C; Gaglione, R; Breton, D R; Bhattacharyya, S; Abbrescia, M; Erriquez, O; Paticchio, V; Cardini, A; Aloisio, A; Turini, N; Bressan, A; Tikhonov, Y; Schumacher, M; Simon, F R; Nowak, S; Herlant, S; Chaus, A; Fanourakis, G; Bressler, S; Homma, Y; Timmermans, J; Fonte, P; Underwood, D G; Azmoun, B; Fassouliotis, D; Wiacek, P; Esteve bosch, R; Dos santos covita, D; Monteiro da silva, A L; Yahlali haddou, N; Marques ferreira dos santos, J; Domingues amaro, F

    The proposed R&D collaboration, RD51, aims at facilitating the development of advanced gas-avalanche detector technologies and associated electronic-readout systems, for applications in basic and applied research. Advances in particle physics have always been enabled by parallel advances in radiation-detector technology. Radiation detection and imaging with gas-avalanche detectors, capable of economically covering large detection volumes with a low material budget, have been playing an important role in many fields. Besides their widespread use in particle-physics and nuclear-physics experiments, gaseous detectors are employed in many other fields: astro-particle research and applications such as medical imaging, material science, and security inspection. While extensively employed at the LHC, RHIC, and other advanced HEP experiments, present gaseous detectors (wire-chambers, drift-tubes, resistive-plate chambers and others) have limitations which may prevent their use in future experiments. Present tec...

  17. Avalanche photodiode based time-of-flight mass spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Ogasawara, Keiichi, E-mail: kogasawara@swri.edu; Livi, Stefano A.; Desai, Mihir I.; Ebert, Robert W.; McComas, David J.; Walther, Brandon C. [Southwest Research Institute, 6220 Culebra Road, San Antonio, Texas 78238 (United States)

    2015-08-15

    This study reports on the performance of Avalanche Photodiodes (APDs) as a timing detector for ion Time-of-Flight (TOF) mass spectroscopy. We found that the fast signal carrier speed in a reach-through type APD enables an extremely short timescale response with a mass or energy independent <2 ns rise time for <200 keV ions (1−40 AMU) under proper bias voltage operations. When combined with a microchannel plate to detect start electron signals from an ultra-thin carbon foil, the APD comprises a novel TOF system that successfully operates with a <0.8 ns intrinsic timing resolution even using commercial off-the-shelf constant-fraction discriminators. By replacing conventional total-energy detectors in the TOF-Energy system, APDs offer significant power and mass savings or an anti-coincidence background rejection capability in future space instrumentation.

  18. Avalanche photodiode based time-of-flight mass spectrometry.

    Science.gov (United States)

    Ogasawara, Keiichi; Livi, Stefano A; Desai, Mihir I; Ebert, Robert W; McComas, David J; Walther, Brandon C

    2015-08-01

    This study reports on the performance of Avalanche Photodiodes (APDs) as a timing detector for ion Time-of-Flight (TOF) mass spectroscopy. We found that the fast signal carrier speed in a reach-through type APD enables an extremely short timescale response with a mass or energy independent <2 ns rise time for <200 keV ions (1-40 AMU) under proper bias voltage operations. When combined with a microchannel plate to detect start electron signals from an ultra-thin carbon foil, the APD comprises a novel TOF system that successfully operates with a <0.8 ns intrinsic timing resolution even using commercial off-the-shelf constant-fraction discriminators. By replacing conventional total-energy detectors in the TOF-Energy system, APDs offer significant power and mass savings or an anti-coincidence background rejection capability in future space instrumentation.

  19. Optimizing the position resolution of a Z-stack microchannel plate resistive anode detector for low intensity signals

    Science.gov (United States)

    Wiggins, B. B.; Richardson, E.; Siwal, D.; Hudan, S.; deSouza, R. T.

    2015-08-01

    A method for achieving good position resolution of low-intensity electron signals using a microchannel plate resistive anode detector is demonstrated. Electron events at a rate of 7 counts s-1 are detected using a Z-stack microchannel plate. The dependence of position resolution on both the distance and the potential difference between the microchannel plate and resistive anode is investigated. Using standard commercial electronics, a measured position resolution of 170 μm (FWHM) is obtained, which corresponds to an intrinsic resolution of 157 μm (FWHM).

  20. Optimizing the position resolution of a Z-stack microchannel plate resistive anode detector for low intensity signals.

    Science.gov (United States)

    Wiggins, B B; Richardson, E; Siwal, D; Hudan, S; deSouza, R T

    2015-08-01

    A method for achieving good position resolution of low-intensity electron signals using a microchannel plate resistive anode detector is demonstrated. Electron events at a rate of 7 counts s(-1) are detected using a Z-stack microchannel plate. The dependence of position resolution on both the distance and the potential difference between the microchannel plate and resistive anode is investigated. Using standard commercial electronics, a measured position resolution of 170 μm (FWHM) is obtained, which corresponds to an intrinsic resolution of 157 μm (FWHM).

  1. Optimizing the position resolution of a Z-stack microchannel plate resistive anode detector for low intensity signals

    Energy Technology Data Exchange (ETDEWEB)

    Wiggins, B. B.; Richardson, E.; Siwal, D.; Hudan, S.; Souza, R. T. de, E-mail: desouza@indiana.edu [Department of Chemistry and Center for Exploration of Energy and Matter, Indiana University, 2401 N. Milo B. Sampson Ln., Bloomington, Indiana 47408 (United States)

    2015-08-15

    A method for achieving good position resolution of low-intensity electron signals using a microchannel plate resistive anode detector is demonstrated. Electron events at a rate of 7 counts s{sup −1} are detected using a Z-stack microchannel plate. The dependence of position resolution on both the distance and the potential difference between the microchannel plate and resistive anode is investigated. Using standard commercial electronics, a measured position resolution of 170 μm (FWHM) is obtained, which corresponds to an intrinsic resolution of 157 μm (FWHM)

  2. Optimization of high count rate event counting detector with Microchannel Plates and quad Timepix readout

    Energy Technology Data Exchange (ETDEWEB)

    Tremsin, A.S., E-mail: ast@ssl.berkeley.edu; Vallerga, J.V.; McPhate, J.B.; Siegmund, O.H.W.

    2015-07-01

    Many high resolution event counting devices process one event at a time and cannot register simultaneous events. In this article a frame-based readout event counting detector consisting of a pair of Microchannel Plates and a quad Timepix readout is described. More than 10{sup 4} simultaneous events can be detected with a spatial resolution of ~55 µm, while >10{sup 3} simultaneous events can be detected with <10 µm spatial resolution when event centroiding is implemented. The fast readout electronics is capable of processing >1200 frames/sec, while the global count rate of the detector can exceed 5×10{sup 8} particles/s when no timing information on every particle is required. For the first generation Timepix readout, the timing resolution is limited by the Timepix clock to 10–20 ns. Optimization of the MCP gain, rear field voltage and Timepix threshold levels are crucial for the device performance and that is the main subject of this article. These devices can be very attractive for applications where the photon/electron/ion/neutron counting with high spatial and temporal resolution is required, such as energy resolved neutron imaging, Time of Flight experiments in lidar applications, experiments on photoelectron spectroscopy and many others.

  3. Measuring position in 2-dimensions using induced signals in a microchannel plate detector

    Science.gov (United States)

    Wiggins, Blake; Desouza, Romualdo

    2017-01-01

    Position-sensitive microchannel plate (MCP) detectors play an important role in the detection of photons, electrons, ions, and neutrons. Recently, a novel approach has been developed to provide position-sensitivity for an MCP detector. In this approach, namely the induced signal approach, the position of the incident particle is determined by sensing the electron cloud emanating from a MCP stack. The induced signals are inherently bipolar, where the negative lobe of the induced signal corresponds to the approach of the electron cloud to the sense wires and the positive lobe corresponds to the recession of the electron cloud from the sense wires. The zero-crossing point is the time at which the centroid of the charge cloud passes the wire plane. For a single incident electron, a spatial resolution of 103 μm (FWHM) has been achieved by utilizing the zero-crossing point of the induced signals. General considerations suggest that this spatial resolution can be improved by using the entire pulse shape information. The fundamentals of the induced signal approach as well as its implementation in slow neutron radiography will be presented. Supported by the US DOE NNSA under Award No. DE-NA0002012.

  4. The analog Resistive Plate Chamber detector of the ARGO-YBJ experiment

    CERN Document Server

    Bartoli, B; Bi, X J; Cao, Z; Catalanotti, S; Chen, S Z; Chen, T L; Cui, S W; Dai, B Z; D'Amone, A; Danzengluobu,; De Mitri, I; Piazzoli, B D'Ettorre; Di Girolamo, T; Di Sciascio, G; Feng, C F; Feng, Zhaoyang; Feng, Zhenyong; Gou, Q B; Guo, Y Q; He, H H; Hu, Haibing; Hu, Hongbo; Iacovacci, M; Iuppa, R; Jia, H Y; Labaciren,; Li, H J; Liu, C; Liu, J; Liu, M Y; Lu, H; Ma, L L; Ma, X H; Mancarella, G; Mari1, S M; Marsella, G; Mastroianni, S; Montini, P; Ning, C C; Perrone, L; Pistilli, P; Salvini1, P; Santonico, R; Shen, P R; Sheng, X D; Shi, F; Surdo, A; Tan, Y H; Vallania, P; Vernetto, S; Vigorito, C; Wang, H; Wu, C Y; Wu, H R; Xue, L; Yang, Q Y; Yang, X C; Yao, Z G; Yuan, A F; Zha, M; Zhang, H M; Zhang, L; Zhang, X Y; Zhang, Y; Zhao, J; Zhaxiciren,; Zhaxisangzhu,; Zhou, X X; Zhu, F R; Zhu, Q Q

    2015-01-01

    The ARGO-YBJ experiment has been in stable data taking from November 2007 till February 2013 at the YangBaJing Cosmic Ray Observatory (4300 m a.s.l.). The detector consists of a single layer of Resistive Plate Chambers (RPCs) ( about 6700 m^2}) operated in streamer mode. The signal pick-up is obtained by means of strips facing one side of the gas volume. The digital readout of the signals, while allows a high space-time resolution in the shower front reconstruction, limits the measurable energy to a few hundred TeV. In order to fully investigate the 1-10 PeV region, an analog readout has been implemented by instrumenting each RPC with two large size electrodes facing the other side of the gas volume. Since December 2009 the RPC charge readout has been in operation on the entire central carpet (about 5800 m^2). In this configuration the detector is able to measure the particle density at the core position where it ranges from tens to many thousands of particles per m^2. Thus ARGO-YBJ provides a highly detailed...

  5. Centroiding algorithms for high speed crossed-strip readout of microchannel plate detectors

    Energy Technology Data Exchange (ETDEWEB)

    Vallerga, John, E-mail: jvv@ssl.berkeley.edu [Space Sciences Laboratory, Univ. of California, Berkeley, 7 Gauss Way, Berkeley, CA 94720-7450 (United States); Tremsin, Anton [Space Sciences Laboratory, Univ. of California, Berkeley, 7 Gauss Way, Berkeley, CA 94720-7450 (United States); Raffanti, Rick [Techne Instruments Inc., 4066 Oakmore Rd, Oakland, CA 94602 (United States); Siegmund, Oswald [Space Sciences Laboratory, Univ. of California, Berkeley, 7 Gauss Way, Berkeley, CA 94720-7450 (United States)

    2011-05-15

    Imaging microchannel plate (MCP) detectors with cross-strip (XS) readout anodes require centroiding algorithms to determine the location of the amplified charge cloud from the incident radiation, be it photon or particle. We have developed a massively parallel XS readout electronic system that employs an amplifier and ADC for each strip and uses this digital data to calculate the centroid of each event in real time using a field programmable gate array (FPGA). Doing the calculations in real time in the front end electronics using an FPGA enables a much higher input event rate, nearly two orders of magnitude faster by avoiding the bandwidth limitations of the raw data transfer to a computer. We report on our detailed efforts to optimize the algorithms used on both 18 and 40 mm diameter XS MCP detector with strip pitch of 640 {mu}m and readout with multiple 32 channel 'Preshape32' ASIC amplifiers (developed at Rutherford Appleton Laboratory). Each strip electrode is continuously digitized to 12 bits at 50 MHz with all 64 digital channels (128 for the 40 mm detector) transferred to a Xilinx Virtex 5 FPGA. We describe how events are detected in the continuous data stream and then multiplexed into firmware modules that spatially and temporally filter and weight the input after applying offset and gain corrections. We will contrast a windowed 'center of gravity' algorithm to a convolution with a special centroiding kernel in terms of resolution and distortion and show results with<20 {mu}m FWHM resolution at input rates>1 MHz.

  6. A two dimensional silicon detectors array for quality assurance in stereotactic radiotherapy: MagicPlate-512

    Energy Technology Data Exchange (ETDEWEB)

    Aldosari, A. H.; Petasecca, M., E-mail: marcop@uow.edu.au; Espinoza, A.; Newall, M.; Fuduli, I.; Porumb, C.; Alshaikh, S.; Alrowaili, Z. A.; Weaver, M.; Metcalfe, P.; Lerch, M. L. F.; Rosenfeld, A. B. [Centre for Medical Radiation Physics, University of Wollongong, Wollongong, NSW 2500 (Australia); Carolan, M. [Centre for Medical Radiation Physics, University of Wollongong, Wollongong, NSW 2500, Australia and Illawarra Cancer Care Centre, Wollongong Hospital, Wollongong, NSW 2500 (Australia); Perevertaylo, V. [SPA-BIT, KIEV 02232 (Ukraine)

    2014-09-15

    Purpose: Silicon diode arrays are commonly implemented in radiation therapy quality assurance applications as they have a number of advantages including: real time operation (compared to the film) and high spatial resolution, large dynamic range and small size (compared to ionizing chambers). Most diode arrays have detector pitch that is too coarse for routine use in small field applications. The goal of this work is to characterize the two-dimensional monolithic silicon diode array named “MagicPlate-512” (MP512) designed for QA in stereotactic body radiation therapy (SBRT) and stereotactic radio surgery (SRS). Methods: MP512 is a silicon monolithic detector manufactured on ap-type substrate. An array contains of 512 pixels with size 0.5 × 0.5 mm{sup 2} and pitch 2 mm with an overall dimension of 52 × 52 mm{sup 2}. The MP512 monolithic detector is wire bonded on a printed circuit board 0.5 mm thick and covered by a thin layer of raisin to preserve the silicon detector from moisture and chemical contamination and to protect the bonding wires. Characterization of the silicon monolithic diode array response was performed, and included pixels response uniformity, dose linearity, percent depth dose, output factor, and beam profiling for beam sizes relevant to SBRT and SRS and depth dose response in comparison with ionization chamber. Results: MP512 shows a good dose linearity (R{sup 2} = 0.998) and repeatability within 0.2%. The measured depth dose response for field size of 10 × 10 cm{sup 2} agreed to within 1.3%, when compared to a CC13 ionization chamber for depths in PMMA up to 30 cm. The output factor of a 6 MV Varian 2100EX medical linac beam measured by MP512 at the isocenter agrees to within 2% when compared to PTW diamond, Scanditronix point EDD-2 diode and MOSkin detectors for field sizes down to 1 × 1 cm{sup 2}. An over response of 4% was observed for square beam size smaller than 1 cm when compared to EBT3 films, while the beam profiles (FWHM) of MP

  7. Assessing the importance of terrain parameters on glide avalanche release

    Science.gov (United States)

    Peitzsch, Erich H.; Hendrikx, Jordy; Fagre, Daniel B.

    2014-01-01

    avalanches failed as cohesive slabs on this bedrock surface. Consequently, surface roughness proved to be a useful descriptive variable to discriminate between slopes that avalanched and those that did not. Annual 'repeat offender' glide avalanche paths were characterized by smooth outcropping rock plates with stratification planes parallel to the slope. Combined with aspect these repeat offenders were also members of the highest glide category. Using this understanding of the role of topographic parameters on glide avalanche activity, a spatial terrain based model was developed to identify other areas with high glide avalanche potential outside of our immediate observation area.

  8. Optical and UV Sensing Sealed Tube Microchannel Plate Imaging Detectors with High Time Resolution

    Science.gov (United States)

    Siegmund, O.; Vallerga, J.; Tremsin, A.; Hull, J.; Elam, J.; Mane, A.

    2014-09-01

    Microchannel plate (MCP) based imaging, photon time tagging detector sealed tube schemes have a unique set of operational features that enable high time resolution astronomical and remote sensing applications to be addressed. New detectors using the cross strip (XS), cross delay line (XDL), or stripline anode readouts, a wide range of photocathode types, and advanced MCP technologies have been implemented to improve many performance characteristics. A variety of sealed tubes have been developed including 18mm XS readout devices with GaAs and SuperGenII photocathodes, 25mm XDL readout devices with SuperGenII and GaN photocathodes, and 20 x 20 cm sealed tubes with bialkali photocathodes and strip line readout. One key technology that has just become viable is the ability to make MCPs using atomic layer deposition (ALD) techniques. This employs nanofabrication of the active layers of an MCP on a microcapillary array. This technique opens new performance opportunities, including, very large MCP areas (>20cm), very low intrinsic background, lower radiation induced background, much longer overall lifetime and gain stability, and markedly lower outgassing which can improve the sealed tube lifetime and ease of fabrication. The XS readout has been implemented in formats of 22mm, 50mm and 100mm, and uses MCP charge signals detected on two orthogonal layers of conductive fingers to encode event X-Y positions. We have achieved spatial resolution XS detectors better than 25 microns FWHM, with good image linearity while at low gain (5 MHz with ~12% dead time and event timing accuracy of ~100ps. XDL sealed tubes in 25mm format demonstrate ~40 micron spatial resolution at up to ~2 MHz event rates, and have been developed with SupergenII visible regime photocathodes. The XDL tubes also achieve ~100 ps time resolution. Most recently ALD MCPs with an opaque GaN photocathode (100-350nm range) on the MCP surface has been demonstrated in a sealed tube configuration. These ALD MCPs show

  9. Characterizing Atacama B-mode Search Detectors with a Half-Wave Plate

    CERN Document Server

    Simon, S M; Campusano, L E; Choi, S K; Crowley, K T; Essinger-Hileman, T; Gallardo, P; Ho, S P; Kusaka, A; Nati, F; Palma, G A; Page, L A; Raghunathan, S; Staggs, S T

    2015-01-01

    The Atacama B-Mode Search (ABS) instrument is a cryogenic ($\\sim$10 K) crossed-Dragone telescope located at an elevation of 5190 m in the Atacama Desert in Chile that observed for three seasons between February 2012 and October 2014. ABS observed the Cosmic Microwave Background (CMB) at large angular scales ($40<\\ell<500$) to limit the B-mode polarization spectrum around the primordial B-mode peak from inflationary gravity waves at $\\ell \\sim100$. The ABS focal plane consists of 480 transition-edge sensor (TES) bolometers. They are coupled to orthogonal polarizations from a planar ortho-mode transducer (OMT) and observe at 145 GHz. ABS employs an ambient-temperature, rapidly rotating half-wave plate (HWP) to mitigate systematic effects and move the signal band away from atmospheric $1/f$ noise, allowing for the recovery of large angular scales. We discuss how the signal at the second harmonic of the HWP rotation frequency can be used for data selection and for monitoring the detector responsivities.

  10. Very high-gain and low-excess noise near-infrared single-photon avalanche detector: an NIR solid state photomultiplier

    Science.gov (United States)

    Linga, Krishna; Yevtukhov, Yuriy; Liang, Bing

    2009-05-01

    A new family of photodetectors with a Discrete Amplification (DA) mechanism allows the realization of very high gain and low excess noise factor in the visible and near infrared spectral regions and offers an alternative to conventional photomultiplier tubes and Geiger mode avalanche photodetectors. These photodetectors can operate in linear detection mode with gain-bandwidth product in excess of 4X1014 and in photon counting mode with count rates up to 108 counts/sec. Potential benefits of this technology over conventional avalanche photodetectors include ultra low excess noise factor, very high gain, and lower reset time (photodetectors in the near infrared wavelength range. The measured devices have the following performance characteristics: gain > 2X105, excess noise factor Lidar, quantum cryptography, night vision and other military, defence and aerospace applications.

  11. Feedback-amplified electrochemical dual-plate boron-doped diamond microtrench detector for flow injection analysis

    Science.gov (United States)

    Lewis, Grace E M; Gross, Andrew J; Kasprzyk-Hordern, Barbara; Lubben, Anneke T; Marken, Frank

    2015-01-01

    An electrochemical flow cell with a boron-doped diamond dual-plate microtrench electrode has been developed and demonstrated for hydroquinone flow injection electroanalysis in phosphate buffer pH 7. Using the electrochemical generator-collector feedback detector improves the sensitivity by one order of magnitude (when compared to a single working electrode detector). The diffusion process is switched from an analyte consuming “external” process to an analyte regenerating “internal” process with benefits in selectivity and sensitivity. PMID:25735831

  12. A cooled avalanche photodiode with high photon detection probability

    Science.gov (United States)

    Robinson, D. L.; Metscher, B. D.

    1986-01-01

    An avalanche photodiode has been operated as a photon-counting detector with 2 to 3 times the sensitivity of currently-available photomultiplier tubes. APD (avalanche photodiodes) detection probabilities that exceed 27% and approach 50% have been measured at an optimum operating temperature which minimizes noise. The sources of noise and their dependence on operating temperature and bias voltage are discussed.

  13. Cross strip anode readouts for large format, photon counting microchannel plate detectors: developing flight qualified prototypes of the detector and electronics

    Science.gov (United States)

    Vallerga, John; Raffanti, Rick; Cooney, Michael; Cumming, Harley; Varner, Gary; Seljak, Andrej

    2014-07-01

    Photon counting microchannel plate (MCP) imagers have been the detector of choice for most UV astronomical missions over the last two decades (e.g. EUVE, FUSE, COS on Hubble etc.). Over this duration, improvements in the MCP laboratory readout technology have resulted in better spatial resolution (x10), temporal resolution (x1000) and output event rate (x100), all the while operating at lower gain (x 10) resulting in lower high voltage requirements and longer MCP lifetimes. One such technology is the parallel cross strip (PXS) readout. Laboratory versions of PXS electronics have demonstrated count rates on the order of 2 MHz, and temporal resolution of ~ 1ns. In 2012 our group at U.C. Berkeley, along with our partners at the U. Hawaii, received a Strategic Astrophysics Technology grant to raise the TRL of the PXS detector and electronics from 4 to 6 by replacing most of the high powered electronics with application specific integrated circuits (ASICs) which will lower the power, mass and volume requirements of the PXS detector. We were also tasked to design and fabricate a "standard" 50mm square active area MCP detector incorporating these electronics that can be environmentally qualified for flight (temperature, vacuum, vibration). The first ASICs designed for this program have been fabricated and are undergoing testing. We present the latest progress on these ASIC designs and performance and show imaging results from the new 50 x 50 mm XS detector.

  14. An optimized process for the production of advanced planar wire grid plates as detectors for high energy physics experiments

    CERN Document Server

    Iacopi, F; Pins, R; Van Hook, R I; Honore, M; Zhukov, V; Van Lancker, L; Van Doninck, W K; Beyne, E

    2001-01-01

    This paper introduces a novel production technique for the planar wire grid plates of microstrip gas chambers (MSGCs, gaseous particle detectors), taking advantage from the typical thin film metallization technologies. The aim of the work here presented has been to manufacture MSGC substrates which can meet the challenging requirements proper to particle tracking detectors in highly ionizing environments. These requirements are mainly represented by high reliability and robustness, since the devices are supposed to operate efficiently for at least 10 years in the extremely hostile conditions foreseen at the large hadron collider at CERN (CH). A detailed process description will be given and results will be analyzed both from the production point of view and from the application of the manufactured prototypes as detectors for high energy physics experiments. (7 refs).

  15. Development of a New Fast Shower Maximum Detector Based on Microchannel Plates Photomultipliers (MCP-PMT) as an Active Element

    Energy Technology Data Exchange (ETDEWEB)

    Ronzhin, A. [Fermilab; Los, S. [Fermilab; Ramberg, E. [Fermilab; Spiropulu, M. [Caltech; Apresyan, A. [Caltech; Xie, S. [Caltech; Kim, H. [Chicago U.; Zatserklyaniy, A. [UC, Santa Cruz

    2014-09-21

    One possibility to make a fast and radiation resistant shower maximum (SM) detector is to use a secondary emitter as an active element. We present below test beam results, obtained with different types of photodetectors based on microchannel plates (MCPs) as the secondary emitter. We performed the measurements at the Fermilab Test Beam Facility with 120GeV proton beam and 12GeV and 32GeV secondary beams. The goal of the measurement with 120GeV protons was to determine time resolution for minimum ionizing particles (MIPs). The SM time resolution we obtained for this new type of detector is at the level of 20-30ps. We estimate that a significant contribution to the detector response originates from secondary emission of the MCP. This work can be considered as the first step in building a new type of calorimeter based on this principle.

  16. Development of a New Fast Shower Maximum Detector Based on Microchannel Plates Photomultipliers (MCP-PMT) as an Active Element

    Energy Technology Data Exchange (ETDEWEB)

    Ronzhin, A. [Fermilab; Los, S. [Fermilab; Ramberg, E. [Fermilab; Spiropulu, M. [Caltech; Apresyan, A. [Caltech; Xie, S. [Caltech; Kim, H. [Chicago U.; Zatserklyaniy, A. [UC, Santa Cruz

    2014-09-21

    One possibility to make a fast and radiation resistant shower maximum (SM) detector is to use a secondary emitter as an active element. We present below test beam results, obtained with different types of photodetectors based on microchannel plates (MCPs) as the secondary emitter. We performed the measurements at the Fermilab Test Beam Facility with 120GeV proton beam and 12GeV and 32GeV secondary beams. The goal of the measurement with 120GeV protons was to determine time resolution for minimum ionizing particles (MIPs). The SM time resolution we obtained for this new type of detector is at the level of 20-30ps. We estimate that a significant contribution to the detector response originates from secondary emission of the MCP. This work can be considered as the first step in building a new type of calorimeter based on this principle.

  17. Performance of Ultra-Fast Silicon Detectors

    CERN Document Server

    Cartiglia, N; Ely, S; Fadeyev, V; Galloway, Z; Marchetto, F; Mazza, G; Ngo, J; Obertino, M; Parker, C; Rivetti, A; Shumacher, D; Sadrozinski, H F-W; Seiden, A; Zatserklyaniy, A

    2013-01-01

    The development of Low-Gain Avalanche Detectors has opened up the possibility of manufacturing silicon detectors with signal larger than that of traditional sensors. In this paper we explore the timing performance of Low-Gain Avalanche Detectors, and in particular we demonstrate the possibility of obtaining ultra-fast silicon detector with time resolution of less than 20 picosecond.

  18. Avalanche speed in thin avalanche photodiodes

    Science.gov (United States)

    Ong, D. S.; Rees, G. J.; David, J. P. R.

    2003-04-01

    The duration of the avalanche multiplication process in thin GaAs avalanche photodiodes is investigated using a full band Monte Carlo (FBMC) model. The results are compared with those of a simple random path length (RPL) model which makes the conventional assumptions of a displaced exponential for the ionization path length probability distribution function and that carriers always travel at their saturated drift velocities. We find that the avalanche duration calculated by the RPL model is almost twice of that predicted by the FBMC model, although the constant drift velocities used in the former model are estimated using the latter. The faster response predicted by FBMC model arises partly from the reduced dead space but mainly from the velocity overshoot of ionizing carriers. While the feedback multiplication processes forced by the effects of dead space extend the avalanche duration in short structures, the effects of velocity overshoot in the realistic model more than compensate, significantly improving multiplication bandwidth.

  19. Photon detection with cooled avalanche photodiodes

    Science.gov (United States)

    Robinson, D. L.; Metscher, B. D.

    1987-01-01

    Commercial avalanche photodiodes have been operated as single-photon detectors at an optimum operating temperature and bias voltage. These detectors were found to be 1.5-3 times more sensitive than presently available photomultiplier tubes (PMTs). Both single-photon detection probability and detector noise increase with bias voltage; detection probabilities greater than twice that of a PMT were obtained with detector noise levels below 100 counts per second. Higher probabilities were measured at higher noise levels. The sources of noise and their dependence on temperature and bias voltage are discussed.

  20. Cooled avalanche photodiode used for photon detection

    Science.gov (United States)

    Robinson, Deborah L.; Metscher, Brian D.

    1987-01-01

    Commercial avalanche photodiodes have been operated as single-photon detectors at an optimum operating temperature and bias voltage. These detectors were found to be 1.5 to 3 times more sensitive than presently-available photomultiplier tubes (PPMTs). Both single-photon detection probability and detector noise increase with bias voltage; detection probabilities greater than 25 percent were obtained with detector noise levels comparable to the noise of a PMT; higher probabilities were measured at higher noise levels. The sources of noise and their dependence on temperature and bias voltage are discussed.

  1. The PRESHOWER - a New Multichnnel Detector for the CDF. The Scintillator Plates of the New Detector: Design, Production, Quality Control

    CERN Document Server

    Artikov, A M; Chocheli, D; Danilov, V; Grinyov, B; Lebedev, V; Senchyshyn, V G

    2005-01-01

    To increase the CDF efficiency when studying heavy quark processes there was designed, constructed and put into operation a new multichannel detector --- the so called Central Preshower. It was positioned before the central electromagnetic calorimeter and increased the photon, lepton and hadron identification efficiency. JINR in cooperation with the Institute of Scintillating Materials (Kharkiv) has created a sensitive element of the new detector: about 2800 units of the scintillation tiles; the specially developed quality control procedure guaranteed the necessary high light yield for tiles mass production. The chosen tiles were equipped at FNAL by two loops (about 1 m long) of WLS fibers positioned inside the $\\Omega $-shape groove; it guaranteed a light yield of $\\sim$ 25--35 photoelectrons/MIP.

  2. Quantum efficiencies of imaging detectors with alkali halide photocathodes. I - Microchannel plates with separate and integral CsI photocathodes

    Science.gov (United States)

    Carruthers, George R.

    1987-01-01

    Measurements and comparisons have been made of the quantum efficiencies of microchannel plate (MCP) detectors in the far-UV (below 2000-A) wavelength range using CsI photocathodes (a) deposited on the front surfaces of microchannel plates and (b) deposited on solid substrates as opaque photocathodes with the resulting photoelectrons input to microchannel plates. The efficiences were measured in both pulse-counting and photodiode modes of operation. Typical efficiencies are about 15 percent at 1216 A for a CsI-coated MCP compared with 65 percent for an opaque CsI photocathode MCP detector. Special processing has yielded an efficiency as high as 20 percent for a CsI-coated MCP. This may possibly be further improved by optimization of the tilt angle of the MCP channels relative to the front face of the MCP and incident radiation. However, at present there still remains a factor of at least 3 quantum efficiency advantage in the separate opaque CsI photocathode configuration.

  3. High-resolution imaging X-ray detector. [using microchannel plates and electronic readout for spaceborne telescope

    Science.gov (United States)

    Kellogg, E.; Henry, P.; Murray, S.; Van Speybroeck, L.; Bjorkholm, P.

    1976-01-01

    The paper describes an X-ray detector using microchannel plates as a photocathode surface and imaging photoelectron multiplier, and a crossed wire grid as a two-dimensional position-sensitive detector. The position resolution is 10 microns. The crossed wire grid consists of 100-micron-diam wires on 200-micron centers. Position sensing is accomplished by electronic interpolation to 1/20 of the wire spacing. The quantum efficiency of the microchannel plates varies from 29% at 0.28 keV to 5% at 3 keV. This detector will provide second-of-arc X-ray imaging in the focal plane of the 342.9-cm focal length grazing-incidence telescope being prepared for the HEAO-B observatory. By addition of suitable photocathodes, it can be used for single-photon imaging light detection in the UV, visible, and near-IR-ranges. In all cases, it gives a very low dark counting rate, allows timing of individual events to 1 microsec or less, and can handle counting rates up to 10,000 per sec.

  4. Single electron multiplication distribution in GEM avalanches

    CERN Document Server

    Laszlo, Andras; Kiss, Gabor; Varga, Dezso

    2016-01-01

    In this paper measurement results and experimental methodology is presented on the determination of multiplication distributions of avalanches in GEM foils initiated by a single electron. The measurement relies on the amplification of photoelectrons by the GEM under study, which is subsequently amplified in an MWPC. The intrinsic detector resolution, namely the sigma over mean ratio of this distribution is also elaborated. Small gain dependence of the avalanche size is observed in the range of net effective gain of 15 to 100. The distribution has an exponentially decaying tail at large amplitudes, whereas the applied working gas is seen to have a well visible effect on the shape of the multiplication distribution at low amplitudes; or equivalently, the working gas has an influence on the intrinsic detector resolution of GEMs via suppression of the low amplitude responses. A sigma over mean ratio down to 0.75 was reached using neon based mixture, whereas other gases provided an intrinsic detector resolution cl...

  5. Atomic layer deposited borosilicate glass microchannel plates for large area event counting detectors

    Science.gov (United States)

    Siegmund, O. H. W.; McPhate, J. B.; Tremsin, A. S.; Jelinsky, S. R.; Hemphill, R.; Frisch, H. J.; Elam, J.; Mane, A.; Lappd Collaboration

    2012-12-01

    Borosilicate glass micro-capillary array substrates with 20 μm and 40 μm pores have been deposited with resistive, and secondary electron emissive, layers by atomic layer deposition to produce functional microchannel plates. Device formats of 32.7 mm and 20 cm square have been fabricated and tested in analog and photon counting modes. The tests show amplification, imaging, background rate, pulse shape and lifetime characteristics that are comparable to standard glass microchannel plates. Large area microchannel plates of this type facilitate the construction of 20 cm format sealed tube sensors with strip-line readouts that are being developed for Cherenkov light detection. Complementary work has resulted in Na2KSb bialkali photocathodes with peak quantum efficiency of 25% being made on borosilicate glass. Additionally GaN (Mg) opaque photocathodes have been successfully made on borosilicate microchannel plates.

  6. Atomic layer deposited borosilicate glass microchannel plates for large area event counting detectors

    Energy Technology Data Exchange (ETDEWEB)

    Siegmund, O.H.W., E-mail: ossy@ssl.berkeley.edu [Experimental Astrophysics Group, Space Sciences Laboratory, 7 Gauss Way, University of California, Berkeley, CA 94720 (United States); McPhate, J.B.; Tremsin, A.S.; Jelinsky, S.R.; Hemphill, R. [Experimental Astrophysics Group, Space Sciences Laboratory, 7 Gauss Way, University of California, Berkeley, CA 94720 (United States); Frisch, H.J. [Enrico Fermi Institute, 5640 S. Ellis Avenue University of Chicago, Chicago, IL 60637 (United States); Elam, J.; Mane, A. [Argonne National Laboratory, 9700 S. Cass Avenue Argonne, IL 60439 (United States); Collaboration: LAPPD Collaboration

    2012-12-11

    Borosilicate glass micro-capillary array substrates with 20 {mu}m and 40 {mu}m pores have been deposited with resistive, and secondary electron emissive, layers by atomic layer deposition to produce functional microchannel plates. Device formats of 32.7 mm and 20 cm square have been fabricated and tested in analog and photon counting modes. The tests show amplification, imaging, background rate, pulse shape and lifetime characteristics that are comparable to standard glass microchannel plates. Large area microchannel plates of this type facilitate the construction of 20 cm format sealed tube sensors with strip-line readouts that are being developed for Cherenkov light detection. Complementary work has resulted in Na{sub 2}KSb bialkali photocathodes with peak quantum efficiency of 25% being made on borosilicate glass. Additionally GaN (Mg) opaque photocathodes have been successfully made on borosilicate microchannel plates.

  7. Applications and characteristics of imaging plates as detector in neutron radiography at SINQ

    CERN Document Server

    Kolbe, H; Gunia, W; Körner, S

    1999-01-01

    Imaging plate technique is a commonly accepted method in many fields as in medicine, biology and physics for detection of the distribution of beta- and gamma-radiation or X-rays on large areas. Recently a new type of imaging plate sensitive to neutrons has been developed. The storage layer is doped with gadolinium, which, after absorption of neutrons, produces radiation detectable by the same sensitive crystals used in conventional imaging plates. At the spallation neutron source, SINQ, at the Paul Scherrer Institut (CH) some of the characteristics of the neutron radiography station in combination with the imaging plate technique were investigated. The intensity distribution of the source was measured to check the accuracy for quantification of the image data. Also, the reproducibility of results obtained by this detection system was stated. For a test object, the high selectivity for different neutron absorption is demonstrated at details with low contrast. The obtainable spatial resolution was determined re...

  8. Imaging at soft X-ray wavelengths with high-gain microchannel plate detector systems

    Science.gov (United States)

    Timothy, J. Gethyn

    1986-01-01

    Multianode microchannel array (MAMA) detector systems with formats of 256 x 1024 pixels and active areas of 6 x 26 mm are now under evaluation at visible, UV and soft X-ray wavelengths. Very-large-format versions of the MAMA detectors with formats of 2048 x 2048 pixels and active areas of 52 x 52 mm are under development for use in the NASA Goddard Space Telescope Imaging Spectrograph (STIS). Open-structure versions of these detectors with Cs I photocathodes can provide a high-resolution imaging capability at EUV and soft X-ray wavelengths and can deliver a maximum count rate from each array in excess of 10 to the 6th counts/s. In addition, these detector systems have the unique capability to determine the arrival time of a detected photon to an accuracy of 100 ns or better. The construction, mode of operation, and performance characteristics of the MAMA detectors are described, and the program for the development of the very-large-format detectors is outlined.

  9. Image translational shifts in microchannel plate detectors due to the presence of MCP channel bias

    CERN Document Server

    Tremsin, A S; Siegmund, O H W

    2002-01-01

    A detailed study of possible image displacements in MCP detectors due to the presence of MCP pore bias is presented. We show that fluctuations of the rear accelerating field, characteristic to some MCP detector configurations, result in translational shifts of the entire image, which degrade the detector spatial resolution. It was experimentally observed that a 10% increase in the rear voltage of 400 V for a detector with 13 deg. -biased MCPs and 8.5 mm MCP-to-anode distance results in a 32 mu m shift of the image in the direction opposite to the pore bias. Increasing the voltage to 800 V induced a 200 mu m image displacement. No displacement was observed for a detector with a 0 deg. -biased output MCP. We also present a model for calculation of the charge footprint centroid in MCP detectors based on the output distribution function of the charge cloud. The results of our computer simulation of the image displacements prove to be in a very good agreement with the experimental data, thus providing the basis fo...

  10. An algorithm for automatic crystal identification in pixelated scintillation detectors using thin plate splines and Gaussian mixture models

    Science.gov (United States)

    Schellenberg, Graham; Stortz, Greg; Goertzen, Andrew L.

    2016-02-01

    A typical positron emission tomography detector is comprised of a scintillator crystal array coupled to a photodetector array or other position sensitive detector. Such detectors using light sharing to read out crystal elements require the creation of a crystal lookup table (CLUT) that maps the detector response to the crystal of interaction based on the x-y position of the event calculated through Anger-type logic. It is vital for system performance that these CLUTs be accurate so that the location of events can be accurately identified and so that crystal-specific corrections, such as energy windowing or time alignment, can be applied. While using manual segmentation of the flood image to create the CLUT is a simple and reliable approach, it is both tedious and time consuming for systems with large numbers of crystal elements. In this work we describe the development of an automated algorithm for CLUT generation that uses a Gaussian mixture model paired with thin plate splines (TPS) to iteratively fit a crystal layout template that includes the crystal numbering pattern. Starting from a region of stability, Gaussians are individually fit to data corresponding to crystal locations while simultaneously updating a TPS for predicting future Gaussian locations at the edge of a region of interest that grows as individual Gaussians converge to crystal locations. The algorithm was tested with flood image data collected from 16 detector modules, each consisting of a 409 crystal dual-layer offset LYSO crystal array readout by a 32 pixel SiPM array. For these detector flood images, depending on user defined input parameters, the algorithm runtime ranged between 17.5-82.5 s per detector on a single core of an Intel i7 processor. The method maintained an accuracy above 99.8% across all tests, with the majority of errors being localized to error prone corner regions. This method can be easily extended for use with other detector types through adjustment of the initial

  11. Recent detector developments at SINTEF (industrial presentation)

    Science.gov (United States)

    Sundby Avset, Berit; Evensen, Lars; Uri Jensen, Geir; Mo, Sjur; Kari Schjølberg-Henriksen; Westgaard, Trond

    1998-02-01

    Results from SINTEF's research on radiation hardness of silicon detectors, thin silicon detectors, silicon drift devices, reach-through avalanche photodiodes, and detectors with thin dead layers are presented.

  12. X-ray photon-counting detector based on a micro-channel plate for pulsar navigation

    Institute of Scientific and Technical Information of China (English)

    Baomei Chen; Baosheng Zhao; Huijun Hu; Qiurong Yan; Lizhi Sheng

    2011-01-01

    The pulse time of arrival (TOA) is a determining parameter for accurate timing and positioning in X-ray pulsar navigation. The pulse TOA can be calculated by comparing the measured arrival time with the predicted arrival time of the X-ray pulse for pulsar. In this study, in order to research the measurement of pulse arrival time, an experimental system is set up. The experimental system comprises a simulator of the X-ray pulsar, an X-ray detector, a time-measurement system, and a data-processing system. An X-ray detector base is proposed on the basis of the micro-channel plate (MCP), which is sensitive to soft X-ray in the 1-10 keV band. The MCP-based detector, the structure and principle of the experimental system, and results of the pulse profile are described in detail. In addition, a discussion of the effects of different X-ray pulse periods and the quantum efficiency of the detector on pulse-profile signal-to-noise ratio (SNR) is presented. Experimental results reveal that the SNR of the measured pulse profile becomes enhanced as the quantum efficiency of the detector increases. The SNR of the pulse profile is higher when the period of the pulse is smaller at the same integral.%@@ The pulse time of arrival (TOA) is a determining parameter for accurate timing and positioning in X-ray pulsar navigation.The pulse TOA can be calculated by comparing the measured arrival time with the predicted arrival time of the X-ray pulse for pulsar.In this study, in order to research the measurement of pulse arrival time, an experimental system is set up.The experimental system comprises a simulator of the X-ray pulsar, an X-ray detector, a time-measurement system, and a data-processing system.An X-ray detector base is proposed on the basis of the micro-channel plate (MCP), which is sensitive to soft X-ray in the 1-10 keV band.The MCP-based detector, the structure and principle of the experimental system,and results of the pulse profile are described in detail.In addition, a

  13. Reducing dose in urography while maintaining image quality - a comparison of storage phosphor plates and a flat-panel detector

    Energy Technology Data Exchange (ETDEWEB)

    Jansson, Margareta; Geijer, Haakan; Andersson, Torbjoern [Oerebro University Hospital, Department of Radiology, Oerebro (Sweden); Persliden, Jan [Oerebro University Hospital, Department of Medical Physics, Oerebro (Sweden); Linkoeping University, Department of Medicine and Care, Faculty of Health Sciences, Linkoeping (Sweden)

    2006-01-01

    The introduction of new flat-panel detector technology often forces us to accept too high dose levels as proposed by the manufacturers. We need a tool to compare the image quality of a new system with the accepted standard. The aim of this study was to obtain a comparable image quality for two systems - storage phosphor plates and a flat-panel system using intravenous urography (IVU) as a clinical model. The image quality figure was calculated using a contrast-detail phantom (CDRAD) for the two evaluated systems. This allowed us to set a dose for the flat-panel system that gave equivalent image quality to the storage phosphor plates. This reduced detector dose was used in an evaluation of clinical images to find out if the dose reduction from the phantom study indeed resulted in images of equal clinical image quality. The image quality was assessed using image criteria of the European guidelines for IVU with visual grading analysis. Equivalent image quality in image pairs was achieved at 30% of the dose. The CDRAD contrast-detail phantom makes it possible to find dose levels that give equal image quality using different imaging systems. (orig.)

  14. PLATE

    DEFF Research Database (Denmark)

    Kling, Joyce; Hjulmand, Lise-Lotte

    2008-01-01

    ’s level of English is sufficient for the increasing number of courses offered in English each semester. This paper addresses these concerns and describes a pilot project initiated in 2003 at CBS to gauge the overall English language proficiency of those teaching content courses in English. Through......Copenhagen Business School (CBS) finds itself needing to address the issue of English-medium instruction for its increasing number of foreign exchange and full degree students. With internationalisation as a main pillar of the institution’s agenda, there are concerns whether the teaching faculty...... the Project in Language Assessment for Teaching in English (PLATE) language professionals from CBS’s Language Center observe teachers and provide feedback using evaluation criteria from the Common European Framework for Reference (CEFR) supplemented by some additional criteria which take the LSP nature...

  15. PLATE

    DEFF Research Database (Denmark)

    Kling, Joyce; Hjulmand, Lise-Lotte

    2008-01-01

    Copenhagen Business School (CBS) finds itself needing to address the issue of English-medium instruction for its increasing number of foreign exchange and full degree students. With internationalisation as a main pillar of the institution’s agenda, there are concerns whether the teaching faculty......’s level of English is sufficient for the increasing number of courses offered in English each semester. This paper addresses these concerns and describes a pilot project initiated in 2003 at CBS to gauge the overall English language proficiency of those teaching content courses in English. Through...... the Project in Language Assessment for Teaching in English (PLATE) language professionals from CBS’s Language Center observe teachers and provide feedback using evaluation criteria from the Common European Framework for Reference (CEFR) supplemented by some additional criteria which take the LSP nature...

  16. Electron avalanches in liquid argon mixtures

    Energy Technology Data Exchange (ETDEWEB)

    Kim, J.G.; Dardin, S.M.; Kadel, R.W.; Kadyk, J.A.; Wenzel, W.B.; Peskov, V.

    2004-03-19

    We have observed stable avalanche gain in liquid argon when mixed with small amounts of xenon in the high electric field (>7 MV/cm) near the point of a chemically etched needle in a point-plane geometry. We identify two gain mechanisms, one pressure dependent, and the other independent of the applied pressure. We conclude that the pressure dependent signals are from avalanche gain in gas bubbles at the tip of the needle, while the pressure independent pulses are from avalanche gain in liquid. We measure the decay time spectra of photons from both types of avalanches. The decay times from the pressure dependent pulses decrease (increase) with the applied pressure (high voltage), while the decay times from the pressure independent pulses are approximately independent of pressure or high voltage. For our operating conditions, the collected charge distribution from avalanches is similar for 60 keV or 122 keV photon sources. With krypton additives, instead of Xe, we measure behavior consistent with only the pressure dependent pulses. Neon and TMS were also investigated as additives, and designs for practical detectors were tested.

  17. Calibration of a Thomson parabola ion spectrometer and Fujifilm imaging plate detectors for protons, deuterons, and alpha particles

    Energy Technology Data Exchange (ETDEWEB)

    Freeman, C. G.; Canfield, M. J.; Graeper, G. B.; Lombardo, A. T.; Stillman, C. R.; Padalino, S. J. [Physics Department, SUNY Geneseo, Geneseo, New York 14454 (United States); Fiksel, G.; Stoeckl, C.; Mileham, C.; Sangster, T. C. [Laboratory for Laser Energetics, University of Rochester, Rochester, New York 14623 (United States); Sinenian, N.; Frenje, J. A. [Plasma Science and Fusion Center, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States)

    2011-07-15

    A Thomson parabola ion spectrometer has been designed for use at the Multiterawatt (MTW) laser facility at the Laboratory for Laser Energetics (LLE) at University of Rochester. This device uses parallel electric and magnetic fields to deflect particles of a given mass-to-charge ratio onto parabolic curves on the detector plane. Once calibrated, the position of the ions on the detector plane can be used to determine the particle energy. The position dispersion of both the electric and magnetic fields of the Thomson parabola was measured using monoenergetic proton and alpha particle beams from the SUNY Geneseo 1.7 MV tandem Pelletron accelerator. The sensitivity of Fujifilm BAS-TR imaging plates, used as a detector in the Thomson parabola, was also measured as a function of the incident particle energy over the range from 0.6 MeV to 3.4 MeV for protons and deuterons and from 0.9 MeV to 5.4 MeV for alpha particles. The device was used to measure the energy spectrum of laser-produced protons at MTW.

  18. Calibration of a Thomson parabola ion spectrometer and Fujifilm imaging plate detectors for protons, deuterons, and alpha particles.

    Science.gov (United States)

    Freeman, C G; Fiksel, G; Stoeckl, C; Sinenian, N; Canfield, M J; Graeper, G B; Lombardo, A T; Stillman, C R; Padalino, S J; Mileham, C; Sangster, T C; Frenje, J A

    2011-07-01

    A Thomson parabola ion spectrometer has been designed for use at the Multiterawatt (MTW) laser facility at the Laboratory for Laser Energetics (LLE) at the University of Rochester. This device uses parallel electric and magnetic fields to deflect particles of a given mass-to-charge ratio onto parabolic curves on the detector plane. Once calibrated, the position of the ions on the detector plane can be used to determine the particle energy. The position dispersion of both the electric and magnetic fields of the Thomson parabola was measured using monoenergetic proton and alpha particle beams from the SUNY Geneseo 1.7 MV tandem Pelletron accelerator. The sensitivity of Fujifilm BAS-TR imaging plates, used as a detector in the Thomson parabola, was also measured as a function of the incident particle energy over the range from 0.6 MeV to 3.4 MeV for protons and deuterons and from 0.9 MeV to 5.4 MeV for alpha particles. The device was used to measure the energy spectrum of laser-produced protons at MTW.

  19. A noiseless kilohertz frame rate imaging detector based on microchannel plates read out with the Medipix2 CMOS pixel chip

    CERN Document Server

    Mikulec, Bettina; Ferrère, Didier; La Marra, Daniel; McPhate, J B; Tremsin, A S; Siegmund, O H W; Vallerga, J V; Clement, J; Ponchut, C; Rigal, J M; CERN. Geneva

    2006-01-01

    A new hybrid optical imaging detector is described that is being developed for the next generation adaptive optics (AO) wavefront sensors (WFS) for ground-based telescopes. The detector consists of a photocathode and proximity focused microchannel plates (MCPs) read out by the Medipix2 CMOS pixel ASIC. Each pixel of the Medipix2 device measures 55x55 um2 and comprises pre-amplifier, a window discriminator and a 14-bit counter. The 256x256 Medipix2 array can be read out noiselessly in 287 us. The readout can be electronically shuttered down to a temporal window of a few us. The Medipix2 is buttable on 3 sides to produce 512x(n*256) pixel devices. Measurements with ultraviolet light yield a spatial resolution of the detector at the Nyquist limit. Sub-pixel resolution can be achieved using centroiding algorithms. For the AO application, very high continuous frame rates of the order of 1 kHz are required for a matrix of 512x512 pixels. The design concepts of a parallel readout board are presented that will allow ...

  20. Electric field distribution and simulation of avalanche formation due to the passage of heavy ions in a parallel grid avalanche counter

    Indian Academy of Sciences (India)

    D Kanjilal; S Saha

    2009-05-01

    Electric field distributions and their role in the formation of avalanche due to the passage of heavy ions in parallel grid avalanche type wire chamber detectors are evaluated using a Monte Carlo simulation. The relative merits and demerits of parallel and crossed wire grid configurations are studied. It is found that the crossed grid geometry has marginally higher gain at larger electric fields close to the avalanche region. The spatial uniformity of response in the two wire grid configurations is also compared.

  1. X-ray imaging using avalanche multiplication in amorphous selenium: investigation of depth dependent avalanche noise.

    Science.gov (United States)

    Hunt, D C; Tanioka, Kenkichi; Rowlands, J A

    2007-03-01

    The past decade has seen the swift development of the flat-panel detector (FPD), also known as the active matrix flat-panel imager, for digital radiography. This new technology is applicable to other modalities, such as fluoroscopy, which require the acquisition of multiple images, but could benefit from some improvements. In such applications where more than one image is acquired less radiation is available to form each image and amplifier noise becomes a serious problem. Avalanche multiplication in amorphous selenium (a-Se) can provide the necessary amplification prior to read out so as to reduce the effect of electronic noise of the FPD. However, in direct conversion detectors avalanche multiplication can lead to a new source of gain fluctuation noise called depth dependent avalanche noise. A theoretical model was developed to understand depth dependent avalanche noise. Experiments were performed on a direct imaging system implementing avalanche multiplication in a layer of a-Se to validate the theory. For parameters appropriate for a diagnostic imaging FPD for fluoroscopy the detective quantum efficiency (DQE) was found to drop by as much as 50% with increasing electric field, as predicted by the theoretical model. This drop in DQE can be eliminated by separating the collection and avalanche regions. For example by having a region of low electric field where x rays are absorbed and converted into charge that then drifts into a region of high electric field where the x-ray generated charge undergoes avalanche multiplication. This means quantum noise limited direct conversion FPD for low exposure imaging techniques are a possibility.

  2. Effect of atmospheric turbulence on the bit error probability of a space to ground near infrared laser communications link using binary pulse position modulation and an avalanche photodiode detector

    Science.gov (United States)

    Safren, H. G.

    1987-01-01

    The effect of atmospheric turbulence on the bit error rate of a space-to-ground near infrared laser communications link is investigated, for a link using binary pulse position modulation and an avalanche photodiode detector. Formulas are presented for the mean and variance of the bit error rate as a function of signal strength. Because these formulas require numerical integration, they are of limited practical use. Approximate formulas are derived which are easy to compute and sufficiently accurate for system feasibility studies, as shown by numerical comparison with the exact formulas. A very simple formula is derived for the bit error rate as a function of signal strength, which requires only the evaluation of an error function. It is shown by numerical calculations that, for realistic values of the system parameters, the increase in the bit error rate due to turbulence does not exceed about thirty percent for signal strengths of four hundred photons per bit or less. The increase in signal strength required to maintain an error rate of one in 10 million is about one or two tenths of a db.

  3. Evaluation of dose distributions in gamma chamber using glass plate detector

    Directory of Open Access Journals (Sweden)

    Narayan Pradeep

    2008-01-01

    Full Text Available A commercial glass plate of thickness 1.75 mm has been utilized for evaluation of dose distributions inside the irradiation volume of gamma chamber using optical densitometry technique. The glass plate showed linear response in the dose range 0.10 Kilo Gray (kGy to 10 kGy of cobalt-60 gamma radiation with optical sensitivity 0.04 Optical Density (OD /kGy. The change in the optical density at each identified spatial dose matrix on the glass plate in relation to the position in the irradiation volume has been presented as dose distributions inside the gamma chamber. The optical density changes have been graphically plotted in the form of surface diagram of color washes for different percentage dose rate levels as isodose distributions in gamma chamber. The variation in dose distribution inside the gamma chamber unit, GC 900, BRIT India make, using this technique has been observed within ± 15%. This technique can be used for routine quality assurances and dose distribution validation of any gamma chamber during commissioning and source replacement. The application of commercial glass plate for dose mapping in gamma chambers has been found very promising due to its wider dose linearity, quick measurement, and lesser expertise requirement in application of the technique.

  4. Some recent developments in nuclear charged particle detectors

    Energy Technology Data Exchange (ETDEWEB)

    Stelzer, H.

    1980-08-01

    The latest developments of large-area, position sensitive gas-filled ionization chambers are described. Multi-wire-proportional chambers as position-sensing and parallel-plate-avalanche counters as time-sensing detectors at low pressure (5 torr) have proven to be useful and reliable instruments in heavy ion physics. Gas (proportional) scintillation counters, used mainly for x-ray spectroscopy, have recently been applied as particle detectors. Finally, a brief description of a large plastic scintillator spectrometer, the Plastic Ball, is given and some of the first test and calibration data are shown.

  5. MagicPlate-512: A 2D silicon detector array for quality assurance of stereotactic motion adaptive radiotherapy

    Energy Technology Data Exchange (ETDEWEB)

    Petasecca, M., E-mail: marcop@uow.edu.au; Newall, M. K.; Aldosari, A. H.; Fuduli, I.; Espinoza, A. A.; Porumb, C. S.; Guatelli, S.; Metcalfe, P.; Lerch, M. L. F.; Rosenfeld, A. B. [Centre for Medical Radiation Physics, University of Wollongong, Wollongong, NSW 2500, Australia and Illawarra Health Medical Research Institute, Wollongong, NSW 2522 (Australia); Booth, J. T.; Colvill, E. [School of Medicine, University of Sydney, Sydney, NSW 2006, Australia and Northern Sydney Cancer Centre, Royal North Shore Hospital, Sydney, NSW 2065 (Australia); Duncan, M.; Cammarano, D. [Centre for Medical Radiation Physics, University of Wollongong, Wollongong, NSW 2500 (Australia); Carolan, M. [Centre for Medical Radiation Physics, University of Wollongong, Wollongong, NSW 2500 (Australia); Illawarra Cancer Care Centre, Wollongong Hospital, Wollongong, NSW 2500 (Australia); Illawarra Health Medical Research Institute, Wollongong, NSW 2522 (Australia); Oborn, B. [Centre for Medical Radiation Physics, University of Wollongong, Wollongong, NSW 2500 (Australia); Illawarra Cancer Care Centre, Wollongong Hospital, Wollongong, NSW 2500 (Australia); Perevertaylo, V. [SPA-BIT, Kiev 02232 (Ukraine); Keall, P. J. [School of Medicine, University of Sydney, Sydney, NSW 2006 (Australia)

    2015-06-15

    , no motion, and motion with MLC tracking profiles agreed within 1 and 0.4 mm, respectively, for all field sizes tested. Use of electromagnetic tracking system generates a fluctuation of the detector baseline up to 10% of the full scale signal requiring a proper shielding strategy. MagicPlate-512 is also able to reconstruct the dose variation pulse-by-pulse in each pixel of the detector. An analysis of the dose transients with motion and motion with tracking shows that the tracking feedback algorithm used for this experiment can compensate effectively only the effect of the slower transient components. The fast changing components of the organ motion can contribute only to discrepancy of the order of 15% in penumbral region while the slower components can change the dose profile up to 75% of the expected dose. Conclusions: MagicPlate-512 is shown to be, potentially, a valid alternative to film or 2D ionizing chambers for quality assurance dosimetry in SRS or SBRT. Its high spatial and temporal resolutions allow for accurate reconstruction of the profile in any conditions with motion and with tracking of the motion. It shows excellent performance to reconstruct the dose deposition in real time or retrospectively as a function of time for detailed analysis of the effect of motion in a specific pixel or area of interest.

  6. Operation of Resistive Plate Chamber Detectors with a New Environmentally Friendly Freon

    CERN Document Server

    Lewis, Helen Elizabeth

    2014-01-01

    RPC particle gas detectors at CERN provide a vital element to the physics experiments carried out on the LHC. While their current operation and working gas mixtures are successful, environ- mental and economic factors force a revision of the mixture, specifically the eventual replacement of the current Freon gas R134-a with a newer, less environmentally harmful formulation, namely R1234-yf. The methods and results presented here outline the detector response to the introduction of the new Freon and its behavior under various mixtures. The electronegativity and hence impact on RPC parameters was investigated. It was found that the new Freon gas is indeed electroneg- ative, and suppresses the RPC signal. The mixture was modified to include Argon to increase ionization, and the final results of the operation of the RPC were satisfactory. Further work to refine the mixture for future implementation is necessary.

  7. Antiproton, positron, and electron imaging with a microchannel plate/phosphor detector

    Science.gov (United States)

    Andresen, G. B.; Bertsche, W.; Bowe, P. D.; Bray, C. C.; Butler, E.; Cesar, C. L.; Chapman, S.; Charlton, M.; El Nasr, S. Seif; Fajans, J.; Fujiwara, M. C.; Gill, D. R.; Hangst, J. S.; Hardy, W. N.; Hayano, R. S.; Hayden, M. E.; Humphries, A. J.; Hydomako, R.; Jørgensen, L. V.; Kerrigan, S. J.; Kurchaninov, L.; Lambo, R.; Madsen, N.; Nolan, P.; Olchanski, K.; Olin, A.; Povilus, A. P.; Pusa, P.; Sarid, E.; Silveira, D. M.; Storey, J. W.; Thompson, R. I.; van der Werf, D. P.; Yamazaki, Y.; Alpha Collaboration

    2009-12-01

    A microchannel plate (MCP)/phosphor screen assembly has been used to destructively measure the radial profile of cold, confined antiprotons, electrons, and positrons in the ALPHA experiment, with the goal of using these trapped particles for antihydrogen creation and confinement. The response of the MCP to low energy (10-200 eV, <1 eV spread) antiproton extractions is compared to that of electrons and positrons.

  8. Assembly and tests of Resistive Plate Chambers (RPC) for the CMS barrel detector

    CERN Multimedia

    Gabriella Pugliese, Bari

    2006-01-01

    The pictures 1-3 show some assembly steps of Resistive Plate Chambers in Bari and their tests with cosmic rays (4-6: moving RPC to the test towers; 7-8 cosmic tests). Pictures 9-10 show assembly and tests in Sofia, 11 shows RPC coupling with drift tubes at ISR and 12-13 tests at the CMS site at CERN.

  9. Antiproton, positron, and electron imaging with a microchannel plate/phosphor detector

    CERN Document Server

    Andresen, G B; Bowe, P D; Bray, C; Butler, E; Cesar, C L; Chapman, S; Charlton, M; Fajans, J; Fujiwara, M C; Gill, D R; Hangst, J S; Hardy, W N; Hayano, R S; Hayden, M E; Humphries, A J; Hydomako, R; Jørgensen, L V; Kerrigan, S J; Kurchaninov, L; Lambo, R; Madsen, N; Nolan, P; Olchanski, K; Olin, A; Povilus, A; Pusa, P; Sarid, E; Seif El Nasr, S; Silveira, D M; Storey, J W; Thompson, R I; van der Werf, D P; Yamazaki, Y

    2009-01-01

    A microchannel plate (MCP)/phosphor screen assembly has been used to destructively measure the radial profile of cold, confined antiprotons, electrons, and positrons in the ALPHA experiment, with the goal of using these trapped particles for antihydrogen creation and confinement. The response of the MCP to low energy (10-200 eV, <1 eV spread) antiproton extractions is compared to that of electrons and positrons.

  10. Rock avalanches on glaciers

    OpenAIRE

    Shugar, Daniel

    2011-01-01

    This thesis examines relations between rock avalanches and the glaciers on which they are deposited. I have attempted to understand a geophysical phenomenon from two viewpoints: sedimentology and glaciology. The contributions are both methodological, and practical. I have used a GIS to quantify debris sheet geomorphology. A thorough characterization of rock avalanche debris is a necessary step in understanding the flow mechanics of large landslide. I have also developed a technique for solvin...

  11. Electrothermal simulation of superconducting nanowire avalanche photodetectors

    Science.gov (United States)

    Marsili, Francesco; Najafi, Faraz; Herder, Charles; Berggren, Karl K.

    2011-02-01

    We developed an electrothermal model of NbN superconducting nanowire avalanche photodetectors (SNAPs) on sapphire substrates. SNAPs are single-photon detectors consisting of the parallel connection of N superconducting nanowires. We extrapolated the physical constants of the model from experimental data and we simulated the time evolution of the device resistance, temperature and current by solving two coupled electrical and thermal differential equations describing the nanowires. The predictions of the model were in good quantitative agreement with the experimental results.

  12. Characterisation of deuterium spectra from laser driven multi-species sources by employing differentially filtered image plate detectors in Thomson spectrometers

    CERN Document Server

    Alejo, A; Ahmed, H; Krygier, A G; Doria, D; Clarke, R; Fernandez, J; Freeman, R R; Fuchs, J; Green, A; Green, J S; Jung, D; Kleinschmidt, A; Lewis, C L S; Morrison, J T; Najmudin, Z; Nakamura, H; Nersisyan, G; Norreys, P; Notley, M; Oliver, M; Roth, M; Ruiz, J A; Vassura, L; Zepf, M; Borghesi, M

    2014-01-01

    A novel method for characterising the full spectrum of deuteron ions emitted by laser driven multi-species ion sources is discussed. The procedure is based on using differential filtering over the detector of a Thompson parabola ion spectrometer, which enables discrimination of deuterium ions from heavier ion species with the same charge-to-mass ratio (such as C6+, O8+, etc.). Commonly used Fuji Image plates were used as detectors in the spectrometer, whose absolute response to deuterium ions over a wide range of energies was calibrated by using slotted CR-39 nuclear track detectors. A typical deuterium ion spectrum diagnosed in a recent experimental campaign is presented.

  13. Position-sensitive detector system OBI for High Resolution X-Ray Powder Diffraction using on-site readable image plates

    Science.gov (United States)

    Knapp, M.; Joco, V.; Baehtz, C.; Brecht, H. H.; Berghaeuser, A.; Ehrenberg, H.; von Seggern, H.; Fuess, H.

    2004-04-01

    A one-dimensional detector system has been developed using image plates. The detector is working in transmission mode or Debye-Scherrer geometry and is on-site readable which reduces the effort for calibration. It covers a wide angular range up to 110° and shows narrow reflection half-widths depending on the capillary diameter. The acquisition time is in the range of minutes and the data quality allows for reliable Rietveld refinement of complicated structures, even in multi-phase samples. The detector opens a wide field of new applications in kinetics and temperature resolved measurements.

  14. Position-sensitive detector system OBI for High Resolution X-Ray Powder Diffraction using on-site readable image plates

    Energy Technology Data Exchange (ETDEWEB)

    Knapp, M. E-mail: mknapp@tu-darmstadt.de; Joco, V.; Baehtz, C.; Brecht, H.H.; Berghaeuser, A.; Ehrenberg, H.; Seggern, H. von; Fuess, H

    2004-04-01

    A one-dimensional detector system has been developed using image plates. The detector is working in transmission mode or Debye-Scherrer geometry and is on-site readable which reduces the effort for calibration. It covers a wide angular range up to 110 deg. and shows narrow reflection half-widths depending on the capillary diameter. The acquisition time is in the range of minutes and the data quality allows for reliable Rietveld refinement of complicated structures, even in multi-phase samples. The detector opens a wide field of new applications in kinetics and temperature resolved measurements.

  15. Design and performance of the detector control system of the ATLAS resistive-plate-chamber muon spectrometer

    Energy Technology Data Exchange (ETDEWEB)

    Polini, Alessandro, E-mail: alessandro.polini@bo.infn.it [INFN Bologna (Italy)

    2012-01-01

    Muon detection plays a key role at the Large Hadron Collider. Resistive plate chambers (RPC) provide the barrel region of the ATLAS detector with an independent muon trigger as well as a two-coordinate measurement. The chambers, arranged in three concentric layers, are operated in a strong magnetic toroidal field and cover a surface area of about 4000 m{sup 2}. The RPC detector control system (DCS) is required to monitor and safely operate tens of thousand of channels, distributed on several subsystems, including low and high voltage power supplies, trigger electronics, currents and thresholds monitoring, environmental sensors and gas and electronic infrastructure. The DCS is also required to provide a level of abstraction for ease of operation as well as specific tools allowing expert actions and detailed analysis of archived data. The hardware architecture and the software solutions adopted are shown in detail along with a few results from the commissioning and first running phases. The material presented here can be used in future test facilities and projects.

  16. Invited article: a test-facility for large-area microchannel plate detector assemblies using a pulsed sub-picosecond laser.

    Science.gov (United States)

    Adams, Bernhard; Chollet, Matthieu; Elagin, Andrey; Oberla, Eric; Vostrikov, Alexander; Wetstein, Matthew; Obaid, Razib; Webster, Preston

    2013-06-01

    The Large Area Picosecond Photodetector Collaboration is developing large-area fast photodetectors with time resolution tests on bare 8 in.-square MCP plates or into a smaller chamber for tests on 33-mm circular substrates. We present the experimental setup, detector calibration, data acquisition, analysis tools, and typical results demonstrating the performance of the test facility.

  17. The Coincident Fission Fragment Detector (CFFD)

    Science.gov (United States)

    Wakhle, A.; Hammerton, K.; Kohley, Z.; Yurkon, J.; Stiefel, K.

    2017-08-01

    A Parallel Plate Avalanche Counter (PPAC) based fission detector system, called the Coincident Fission Fragment Detector (CFFD), has been developed for the ReA3 re-accelerator facility of the National Superconducting Cyclotron Laboratory (NSCL). Binary reaction kinematics are reconstructed based on position and time-of-flight measurements of fission fragments. Large area PPACs provide 1 ns level time resolution and mm level position resolution. The detectors allow measurements of fission product angular and mass distributions of heavy-ion induced fusion reactions. The 30 cm by 40 cm active area of each PPAC provides large solid angle coverage well suited for measurements of low intensity rare-isotope beams (RIBs).

  18. Hard X-ray texture measurements with an on-line image plate detector

    CERN Document Server

    Wcislak, L; Tschentscher, T; Klein, H; Bunge, H J

    2001-01-01

    An instrument for diffraction texture measurements in polycrystalline bulk materials using hard X-ray photons from the wiggler beamline BW5 at HASYLAB is described. High-energy photons in the 100 keV regime enable high penetration power in medium-to-high Z materials and the use of Laue diffraction geometry in combination with a two-dimensional area detector allows fast and convenient data collection. Determination of quantitative, high-resolution pole figures with a better angular resolution of 0.1 deg. is attained by the instrument. Profile analysis of the diffraction pattern parameters for each (h k l)-reflection thus provides, in addition to texture data, information about other microstructural quantities, e.g. lattice strain.

  19. High counting rate resistive-plate chamber

    Science.gov (United States)

    Peskov, V.; Anderson, D. F.; Kwan, S.

    1993-05-01

    Parallel-plate avalanche chambers (PPAC) are widely used in physics experiments because they are fast (less than 1 ns) and have very simple construction: just two parallel metallic plates or mesh electrodes. Depending on the applied voltage they may work either in spark mode or avalanche mode. The advantage of the spark mode of operation is a large signal amplitude from the chamber, the disadvantage is that there is a large dead time (msec) for the entire chamber after an event. The main advantage of the avalanche mode is high rate capability 10(exp 5) counts/mm(sup 2). A resistive-plate chamber (RPC) is similar to the PPAC in construction except that one or both of the electrodes are made from high resistivity (greater than 10(exp 10) Omega(cm) materials. In practice RPC's are usually used in the spark mode. Resistive electrodes are charged by sparks, locally reducing the actual electric field in the gap. The size of the charged surface is about 10 mm(sup 2), leaving the rest of the detector unaffected. Therefore, the rate capability of such detectors in the spark mode is considerably higher than conventional spark counters. Among the different glasses tested the best results were obtained with electron type conductive glasses, which obey Ohm's law. Most of the work with such glasses was done with high pressure parallel-plate chambers (10 atm) for time-of-flight measurements. Resistive glasses have been expensive and produced only in small quantities. Now resistive glasses are commercially available, although they are still expensive in small scale production. From the positive experience of different groups working with the resistive glasses, it was decided to review the old idea to use this glass for the RPC. This work has investigated the possibility of using the RPC at 1 atm and in the avalanche mode. This has several advantages: simplicity of construction, high rate capability, low voltage operation, and the ability to work with non-flammable gases.

  20. Low dose digital X-ray imaging with avalanche amorphous selenium

    Science.gov (United States)

    Scheuermann, James R.; Goldan, Amir H.; Tousignant, Olivier; Léveillé, Sébastien; Zhao, Wei

    2015-03-01

    Active Matrix Flat Panel Imagers (AMFPI) based on an array of thin film transistors (TFT) have become the dominant technology for digital x-ray imaging. In low dose applications, the performance of both direct and indirect conversion detectors are limited by the electronic noise associated with the TFT array. New concepts of direct and indirect detectors have been proposed using avalanche amorphous selenium (a-Se), referred to as high gain avalanche rushing photoconductor (HARP). The indirect detector utilizes a planar layer of HARP to detect light from an x-ray scintillator and amplify the photogenerated charge. The direct detector utilizes separate interaction (non-avalanche) and amplification (avalanche) regions within the a-Se to achieve depth-independent signal gain. Both detectors require the development of large area, solid state HARP. We have previously reported the first avalanche gain in a-Se with deposition techniques scalable to large area detectors. The goal of the present work is to demonstrate the feasibility of large area HARP fabrication in an a-Se deposition facility established for commercial large area AMFPI. We also examine the effect of alternative pixel electrode materials on avalanche gain. The results show that avalanche gain > 50 is achievable in the HARP layers developed in large area coaters, which is sufficient to achieve x-ray quantum noise limited performance down to a single x-ray photon per pixel. Both chromium (Cr) and indium tin oxide (ITO) have been successfully tested as pixel electrodes.

  1. ASSEMBLY and CHARACTERIZATION OF RESISTIVE PLATE CHAMBERS IN INDIA FOR THE CMS DETECTOR

    CERN Document Server

    Kumar, Ramandeep

    2015-01-01

    The Compact Muon Solenoid (CMS) experiment is a general purpose detector being operated at Large Hadron Collider (LHC) facility at CERN. The RE4 upgrade project was envisaged to improve the Level-1 trigger efficiency in the forward region, when LHC would run at its full designed energy and luminosity after the first Long Shutdown (LS-1, 2013-2014). About 200 RPCs were built for the upgrade at three assembly sites in India, CERN and Ghent. India contributed to 50, RE4/2 RPCs along with 200 Cu-cooling units for the entire upgrade for which the assembly and characterization of RPCs was carried out jointly by Nuclear Physics Division-BARC and Panjab University-Chandigarh. The gas-gaps after their arrival from KODEL, South Korea, underwent mechanical tests for leak and popped spacers, followed by electrical tests for long term monitoring of leakage currents. After the assembly, each RPC was evaluated for its efficiency, cluster size, noise and strip profiles. The Cu-cooling units build at BARC were also tested acc...

  2. Development of Multi-gap Resistive Plate Chamber (MRPC) for medical imaging

    Energy Technology Data Exchange (ETDEWEB)

    Banerjee, A.; Roy, A. [Variable Energy Cyclotron Centre, 1/AF Bidhan Nagar, Kolkata 700 064 (India); Biswas, S., E-mail: saikat.ino@gmail.com [Variable Energy Cyclotron Centre, 1/AF Bidhan Nagar, Kolkata 700 064 (India); GSI Helmholtzzentrum für Schwerionenforschung GmbH, Darmstadt 64291 (Germany); Chattopadhyay, S.; Das, G.; Pal, S. [Variable Energy Cyclotron Centre, 1/AF Bidhan Nagar, Kolkata 700 064 (India)

    2013-08-01

    The low cost and high resolution Multi-gap Resistive Plate Chamber (MRPC) opens up a new possibility to find an efficient alternative detector for the Time of Flight (TOF) based Positron Emission Tomography, where the sensitivity of the system depends largely on the time resolution of the detector. In a layered structure, suitable converters can be used to increase the photon detection efficiency. In this paper results of the cosmic ray test of a four-gap bakelite-based prototype MRPC operated in streamer mode and six-gap glass-based MRPC operated in avalanche mode are discussed.

  3. Saturated logistic avalanche model

    Science.gov (United States)

    Aielli, G.; Camarri, P.; Cardarelli, R.; Di Ciaccio, A.; Liberti, B.; Paoloni, A.; Santonico, R.

    2003-08-01

    The search for an adequate avalanche RPC working model evidenced that the simple exponential growth can describe the electron multiplication phenomena in the gas with acceptable accuracy until the external electric field is not perturbed by the growing avalanche. We present here a model in which the saturated growth induced by the space charge effects is explained in a natural way by a constant coefficient non-linear differential equation, the Logistic equation, which was originally introduced to describe the evolution of a biological population in a limited resources environment. The RPCs, due to the uniform and intense field, proved to be an ideal device to test experimentally the presented model.

  4. Dune Avalanche Scars

    Science.gov (United States)

    2004-01-01

    05 August 2004 This Mars Global Surveyor (MGS) Mars Orbiter Camera (MOC) image shows large, low albedo (dark) sand dunes in Kaiser Crater near 47.2oS, 340.4oW. The dunes are--ever so slowly--moving east to west (right to left) as sand avalanches down the steeper, slip face slopes of each. Avalanching sand in the Kaiser dune field has left deep scars on these slopes, suggesting that the sand is not loose but is instead weakly cemented. The image covers an area approximately 3 km (1.9 mi) wide and is illuminated by sunlight from the upper left.

  5. Avalanches in functional materials and geophysics

    CERN Document Server

    Saxena, Avadh; Planes, Antoni

    2017-01-01

    This book provides the state-of-the art of the present understanding of avalanche phenomena in both functional materials and geophysics. The main emphasis of the book is analyzing these apparently different problems within the common perspective of out-of-equilibrium phenomena displaying spatial and temporal complexity that occur in a broad range of scales. Many systems, when subjected to an external force, respond intermittently in the form of avalanches that often span over a wide range of sizes, energies and durations. This is often related to a class of critical behavior characterized by the absence of characteristic scales. Typical examples are magnetization processes, plastic deformation and failure occuring in functional materials. These phenomena share many similarities with seismicity arising from the earth crust failure due to stresses that originate from plate tectonics.

  6. Abelian avalanches and Tutte polynomials

    Science.gov (United States)

    Gabrielov, Andrei

    1993-04-01

    We introduce a class of deterministic lattice models of failure, Abelian avalanche (AA) models, with continuous phase variables, similar to discrete Abelian sandpile (ASP) models. We investigate analytically the structure of the phase space and statistical properties of avalanches in these models. We show that the distributions of avalanches in AA and ASP models with the same redistribution matrix and loading rate are identical. For an AA model on a graph, statistics of avalanches is linked to Tutte polynomials associated with this graph and its subgraphs. In the general case, statistics of avalanches is linked to an analog of a Tutte polynomial defined for any symmetric matrix.

  7. Reuyl Crater Dust Avalanches

    Science.gov (United States)

    2002-01-01

    (Released 13 May 2002) The Science The rugged, arcuate rim of the 90 km crater Reuyl dominates this THEMIS image. Reuyl crater is at the southern edge of a region known to be blanketed in thick dust based on its high albedo (brightness) and low thermal inertia values. This thick mantle of dust creates the appearance of snow covered mountains in the image. Like snow accumulation on Earth, Martian dust can become so thick that it eventually slides down the face of steep slopes, creating runaway avalanches of dust. In the center of this image about 1/3 of the way down is evidence of this phenomenon. A few dozen dark streaks can be seen on the bright, sunlit slopes of the crater rim. The narrow streaks extend downslope following the local topography in a manner very similar to snow avalanches on Earth. But unlike their terrestrial counterparts, no accumulation occurs at the bottom. The dust particles are so small that they are easily launched into the thin atmosphere where they remain suspended and ultimately blow away. The apparent darkness of the avalanche scars is due to the presence of relatively dark underlying material that becomes exposed following the passage of the avalanche. Over time, new dust deposition occurs, brightening the scars until they fade into the background. Although dark slope streaks had been observed in Viking mission images, a clear understanding of this dynamic phenomenon wasn't possible until the much higher resolution images from the Mars Global Surveyor MOC camera revealed the details. MOC images also showed that new avalanches have occurred during the time MGS has been in orbit. THEMIS images will allow additional mapping of their distribution and frequency, contributing new insights about Martian dust avalanches. The Story The stiff peaks in this image might remind you of the Alps here on Earth, but they really outline the choppy edge of a large Martian crater over 50 miles wide (seen in the context image at right). While these aren

  8. Note: A two-dimensional position-sensitive micro-channel plate detector with a cross-connected-pixels resistive anode and integrated spectroscopy amplifiers.

    Science.gov (United States)

    Yang, Liping; Liu, Junliang; Zhang, Yuezhao; Wang, Wei; Yu, Deyang; Li, Xiaoxiao; Li, Xin; Zheng, Min; Ding, Baowei; Cai, Xiaohong

    2017-08-01

    Based on the charge-division method, a compact detector system for charged particles is constructed. The system consists of a pair of micro-channel plates, a novel two-dimensional position-sensitive cross-connected-pixels resistive anode, and specially designed front-end electronics that can directly drive analog-to-digital converters. The detector is tested with an (241)Am α-source. A position resolution of better than 0.3 mm and a maximum distortion within 0.5 mm in the active dimensions of 100 mm diameter are achieved.

  9. Note: A two-dimensional position-sensitive micro-channel plate detector with a cross-connected-pixels resistive anode and integrated spectroscopy amplifiers

    Science.gov (United States)

    Yang, Liping; Liu, Junliang; Zhang, Yuezhao; Wang, Wei; Yu, Deyang; Li, Xiaoxiao; Li, Xin; Zheng, Min; Ding, Baowei; Cai, Xiaohong

    2017-08-01

    Based on the charge-division method, a compact detector system for charged particles is constructed. The system consists of a pair of micro-channel plates, a novel two-dimensional position-sensitive cross-connected-pixels resistive anode, and specially designed front-end electronics that can directly drive analog-to-digital converters. The detector is tested with an 241Am α-source. A position resolution of better than 0.3 mm and a maximum distortion within 0.5 mm in the active dimensions of 100 mm diameter are achieved.

  10. [First experiments for the detection of simulated mammographic lesions: digital full field mammography with a new detector with a double plate of pure selenium].

    Science.gov (United States)

    Schulz-Wendtland, R; Hermann, K-P; Wenkel, E; Adamietz, B; Lell, M; Anders, K; Uder, M

    2011-02-01

    The article describes an experimental phantom study of a system for digital full field mammography with a new digital detector with a double plate of pure selenium. The experiments were carried out with the new full field digital mammography system Amulet from FujiFilm. This system has a new detector (18×24 cm(2)) on the basis of highly purified amorphous selenium (a-Se) with a pixel size of 50 µm. The x-rays are converted into electric signals in the first plate which are read into the second plate with the help of an optical switch and demonstrated in the form of an image. In this way a better pixel size/volume and signal-to-noise ratio should be achieved. The object of the investigation was the Wisconsin Mammographic Random Phantom, Model 152 A (Technical Performance Mo/Mo, 28 kV, 100 mAs). Five investigators with different experiences in mammography each received three images on a monitor with different random positions of the simulated lesions in the phantom for assessment. The detection rates were compared under the same conditions with the results of two other full field digital mammography systems. The median detection rate for all images and investigators for the new doubled plated a-Se detector with optical switch was 98.7%. For both other systems with a-Si or and a-Se detectors the detection rate was 89.8% or 97.3%, respectively. There were no significant differences in the detection rate of the simulated breast lesions for all three systems considering the interobserver and intraobserver variation. The first phantom study for the detection of simulated breast lesions with the new full field digital mammography system Amulet demonstrates equivalent results with the other systems used in the clinical routine. The trend towards superiority of the new system has to be confirmed in further clinical studies.

  11. Investigation of avalanche photodiodes radiation hardness for baryonic matter studies

    CERN Document Server

    Kushpil, V; Ladygin, V P; Kugler, A; Kushpil, S; Svoboda, O; Tlustý, P

    2015-01-01

    Modern avalanche photodiodes (APDs) with high gain are good device candidates for light readout from detectors applied in relativistic heavy ion collisions experiments. The results of the investigations of the APDs properties from Zecotek, Ketek and Hamamatsu manufacturers after irradiation using secondary neutrons from cyclotron facility U120M at NPI of ASCR in \\v{R}e\\v{z} are presented. The results of the investigations can be used for the design of the detectors for the experiments at NICA and FAIR.

  12. Statistical theory of hierarchical avalanche ensemble

    OpenAIRE

    Olemskoi, Alexander I.

    1999-01-01

    The statistical ensemble of avalanche intensities is considered to investigate diffusion in ultrametric space of hierarchically subordinated avalanches. The stationary intensity distribution and the steady-state current are obtained. The critical avalanche intensity needed to initiate the global avalanche formation is calculated depending on noise intensity. The large time asymptotic for the probability of the global avalanche appearance is derived.

  13. Solid-state flat panel imager with avalanche amorphous selenium

    Science.gov (United States)

    Scheuermann, James R.; Howansky, Adrian; Goldan, Amir H.; Tousignant, Olivier; Levéille, Sébastien; Tanioka, K.; Zhao, Wei

    2016-03-01

    Active matrix flat panel imagers (AMFPI) have become the dominant detector technology for digital radiography and fluoroscopy. For low dose imaging, electronic noise from the amorphous silicon thin film transistor (TFT) array degrades imaging performance. We have fabricated the first prototype solid-state AMFPI using a uniform layer of avalanche amorphous selenium (a-Se) photoconductor to amplify the signal to eliminate the effect of electronic noise. We have previously developed a large area solid-state avalanche a-Se sensor structure referred to as High Gain Avalanche Rushing Photoconductor (HARP) capable of achieving gains of 75. In this work we successfully deposited this HARP structure onto a 24 x 30 cm2 TFT array with a pixel pitch of 85 μm. An electric field (ESe) up to 105 Vμm-1 was applied across the a-Se layer without breakdown. Using the HARP layer as a direct detector, an X-ray avalanche gain of 15 +/- 3 was achieved at ESe = 105 Vμm-1. In indirect mode with a 150 μm thick structured CsI scintillator, an optical gain of 76 +/- 5 was measured at ESe = 105 Vμm-1. Image quality at low dose increases with the avalanche gain until the electronic noise is overcome at a constant exposure level of 0.76 mR. We demonstrate the success of a solid-state HARP X-ray imager as well as the largest active area HARP sensor to date.

  14. Development of two-channel prototype ITER vacuum ultraviolet spectrometer with back-illuminated charge-coupled device and microchannel plate detectors.

    Science.gov (United States)

    Seon, C R; Choi, S H; Cheon, M S; Pak, S; Lee, H G; Biel, W; Barnsley, R

    2010-10-01

    A vacuum ultraviolet (VUV) spectrometer of a five-channel spectral system is designed for ITER main plasma impurity measurement. To develop and verify the system design, a two-channel prototype system is fabricated with No. 3 (14.4-31.8 nm) and No. 4 (29.0-60.0 nm) among the five channels. The optical system consists of a collimating mirror to collect the light from source to slit, two holographic diffraction gratings with toroidal geometry, and two different electronic detectors. For the test of the prototype system, a hollow cathode lamp is used as a light source. To find the appropriate detector for ITER VUV system, two kinds of detectors of the back-illuminated charge-coupled device and the microchannel plate electron multiplier are tested, and their performance has been investigated.

  15. A high resolution, high frame rate detector based on a microchannel plate read out with the Medipix2 counting CMOS pixel chip.

    CERN Document Server

    Mikulec, Bettina; McPhate, J B; Tremsin, A S; Siegmund, O H W; Clark, Allan G; CERN. Geneva

    2005-01-01

    The future of ground-based optical astronomy lies with advancements in adaptive optics (AO) to overcome the limitations that the atmosphere places on high resolution imaging. A key technology for AO systems on future very large telescopes are the wavefront sensors (WFS) which detect the optical phase error and send corrections to deformable mirrors. Telescopes with >30 m diameters will require WFS detectors that have large pixel formats (512x512), low noise (<3 e-/pixel) and very high frame rates (~1 kHz). These requirements have led to the idea of a bare CMOS active pixel device (the Medipix2 chip) functioning in counting mode as an anode with noiseless readout for a microchannel plate (MCP) detector and at 1 kHz continuous frame rate. First measurement results obtained with this novel detector are presented both for UV photons and beta particles.

  16. AVALANCHES - EXTREME WINTER EVENTS. MONITORING AND AVALANCHE RISK

    Directory of Open Access Journals (Sweden)

    NARCISA MILIAN

    2012-03-01

    Full Text Available This paper presents the avalanches monitored by the National Meteorological Administration within the nivo-meteorological program since february 2004. Daily observations and weekly snow measurements are made at the weather stations from Bucegi Mountains - Vârful Omu (2504 m, Sinaia (1500 m şi Predeal (1100m and Făgăraş Mountains – Bâlea-Lac (2055m, to provide data for avalanche risk estimation using the european avalanche danger scale. Increasing winter sport activities had led to several avalanche accidents, some of them fatal.

  17. Proposal for the RPC muon detector of LHCb

    CERN Document Server

    Adinolfi, M; Calvetti, M; Carboni, G; Iacopini, E; Messi, R; Pacciani, L; Passaleva, G; Santovetti, E; Santovetti, Emanuele

    2000-01-01

    2000-053 We propose to use RPCs to equip a substantial part of the muon detector stations M2-M5. RPCs made of phenolic plates of low resistivity (9 10^9 ohm-cm) and operated in avalanche mode offer very good performance and several advantages in region IV of M2-M5 and in region III of M4-M5. Using this technique it is possible to cover 75 % of the total area behind the calorimeters at moderate cost.

  18. New focal plane detector system for the broad range spectrometer

    Energy Technology Data Exchange (ETDEWEB)

    Sjoreen, T.P.

    1984-01-01

    A focal plane detector system consisting of a vertical drift chamber, parallel plate avalanche counters, and an ionization chamber with segmented anodes has been installed in the Broad Range Spectrometer at the Holifield Facility at Oak Ridge. The system, which has been designed for use with light-heavy ions with energies ranging from 10 to 25 MeV/amu, has a position resolution of approx. 0.1 mm, a scattering angle resolution of approx. 3 mrad, and a mass resolution of approx. 1/60.

  19. Radiation damage effect on avalanche photodiodes

    CERN Document Server

    Baccaro, S; Cavallari, F; Da Ponte, V; Deiters, K; Denes, P; Diemoz, M; Kirn, Th; Lintern, A L; Longo, E; Montecchi, M; Musienko, Y; Pansart, J P; Renker, D; Reucroft, S; Rosi, G; Rusack, R; Ruuska, D; Stephenson, R; Torbet, M J

    1999-01-01

    Avalanche Photodiodes have been chosen as photon sensors for the electromagnetic calorimeter of the CMS experiment at the LHC. These sensors should operate in the 4T magnetic field of the experiment. Because of the high neutron radiation in the detector extensive studies have been done by the CMS collaboration on the APD neutron radiation damage. The characteristics of these devices after irradiation have been analized, with particular attention to the quantum efficiency and the dark current. The recovery of the radiation induced dark current has been studied carefully at room temperature and at slightly lower and higher temperatures. The temperature dependence of the defects decay-time has been evaluated.

  20. Avalanche Photodiode Arrays for Optical Communications Receivers

    Science.gov (United States)

    Srinivasan, M.; Vilnrotter, V.

    2001-01-01

    An avalanche photodiode (APD) array for ground-based optical communications receivers is investigated for the reception of optical signals through the turbulent atmosphere. Kolmogorov phase screen simulations are used to generate realistic spatial distributions of the received optical field. It is shown that use of an APD array for pulse-position modulation detection can improve performance by up to 4 dB over single APD detection in the presence of turbulence, but that photon-counting detector arrays yield even greater gains.

  1. Experimental evaluation of the response of micro-channel plate detector to ions with 10s of MeV energies

    Science.gov (United States)

    Jeong, Tae Won; Singh, P. K.; Scullion, C.; Ahmed, H.; Kakolee, K. F.; Hadjisolomou, P.; Alejo, A.; Kar, S.; Borghesi, M.; Ter-Avetisyan, S.

    2016-08-01

    The absolute calibration of a microchannel plate (MCP) assembly using a Thomson spectrometer for laser-driven ion beams is described. In order to obtain the response of the whole detection system to the particles' impact, a slotted solid state nuclear track detector (CR-39) was installed in front of the MCP to record the ions simultaneously on both detectors. The response of the MCP (counts/particles) was measured for 5-58 MeV carbon ions and for protons in the energy range 2-17.3 MeV. The response of the MCP detector is non-trivial when the stopping range of particles becomes larger than the thickness of the detector. Protons with energies E ≳ 10 MeV are energetic enough that they can pass through the MCP detector. Quantitative analysis of the pits formed in CR-39 and the signal generated in the MCP allowed to determine the MCP response to particles in this energy range. Moreover, a theoretical model allows to predict the response of MCP at even higher proton energies. This suggests that in this regime the MCP response is a slowly decreasing function of energy, consistently with the decrease of the deposited energy. These calibration data will enable particle spectra to be obtained in absolute terms over a broad energy range.

  2. Characteristics of avalanche accidents and a overview of avalanche equipment

    Directory of Open Access Journals (Sweden)

    Mateusz Biela

    2015-12-01

    Full Text Available Avalanches are one of the most spectacular phenomena which may occur in the mountains. Unfortunately they are often caused by humans and pose for him a big danger. In the Polish Tatras alone they represent 18% of all causes of death among 1996-2013. One fourth of the people caught by an avalanche dies, and their chances of survival depends on the depth of burial, burial time, the presence of an air pocket and the degree of injuries. The most common cause of death is asphyxiation, the next is injuries and hypothermia is the rarest cause of death. The fate of the buried people depends on their equipment such as avalanche transceiver, ABS backpack and AvaLung, and also from the equipment of the people who are seeking (avalanche probes, avalanche transceiver and shovels, which has been proven in practice and research.

  3. Contribution of plated-out 218Po and 214Po to measurements of airborne 222Rn and daughters with plastic (CR-39) nuclear track detectors

    Science.gov (United States)

    Kahn, Bernd; Wang, Zuoyuan; Sensistaffar, Edwin

    1984-01-01

    The fraction of alpha-particle tracks due to radioactivity plated out on its surface was measured for CR-39 nuclear track detector foils used to determine working level values in air. Bare foils were exposed to known concentrations of airborne 222Rn and its short-lived daughters in a calibration chamber. The amounts of 218Po and 214Po on the foil surface were measured with a calibrated diffused junction detector-spectrometer system immediately after the foils were removed from the chamber. Deposition was mostly by 218Po, with some 214Pb but essentially no 214Bi. The track density due to the plated-out radionuclides and the 222Rn, 218Po, and 214Po in chamber air was calculated and compared to the value measured by electrochemical etching. The calculated values generally were slightly above the measured values. On the basis of these calculations, the deposited radioactivity contributed slightly less than one-half of the total tracks in one test and slightly more than two-thirds in another. This effect complicates calibration of the detector relative to airborne radon daughters.

  4. Single and few photon avalanche photodiode detection process study

    Science.gov (United States)

    Blazej, Josef; Prochazka, Ivan

    2009-07-01

    We are presenting the results of the study of the Single Photon Avalanche Diode (SPAD) pulse response risetime and its dependence on several key parameters. We were investigating the unique properties of K14 type SPAD with its high delay uniformity of 200 μm active area and the correlation between the avalanche buildup time and the photon number involved in the avalanche trigger. The detection chip was operated in a passive quenching circuit with active gating. This setup enabled us to monitor the diode reverse current using an electrometer, a fast digitizing oscilloscope, and using a custom design comparator circuit. The electrometer reading enabled to estimate the photon number per detection event, independently on avalanche process. The avalanche build up was recorded on the oscilloscope and processed by custom designed waveform analysis package. The correlation of avalanche build up to the photon number, bias above break, photon absorption location, optical pulse length and photon energy was investigated in detail. The experimental results are presented. The existing solid state photon counting detectors have been dedicated for picosecond resolution and timing stability of single photon events. However, the high timing stability is maintained for individual single photons detection, only. If more than one photon is absorbed within the detector time resolution, the detection delay will be significantly affected. This fact is restricting the application of the solid state photon counters to cases where single photons may be guaranteed, only. For laser ranging purposes it is highly desirable to have a detector, which detects both single photon and multi photon signals with picoseconds stability. The SPAD based photon counter works in a purely digital mode: a uniform output signal is generated once the photon is detected. If the input signal consists of several photons, the first absorbed one triggers the avalanche. Obviously, for multiple photon signals, the

  5. Avalanches in UGe 2

    Science.gov (United States)

    Lhotel, E.; Paulsen, C.; Huxley, A. D.

    2004-05-01

    In UGe 2 ferromagnetism and superconductivity co-exist for pressures in the range 1.0- 1.6 GPa. The magnetic state, however, has several unusual properties. Here we report measurements of hysteresis loops for fields parallel to the easy-axis at low temperature and ambient pressure, measured for two separate UGe 2 single crystals. Steps in the magnetization as the field is changed at low temperature are observed for both crystals. The general phenomenology associated with the steps strongly suggests that they correspond to avalanches of domain-wall motion.

  6. Noiseless, kilohertz-frame-rate, imaging detector based on micro-channel plates readout with the Medipix2 CMOS pixel chip

    CERN Document Server

    McPhate, J; Tremsin, A; Siegmund, O; Mikulec, Bettina; Clark, Allan G; CERN. Geneva

    2005-01-01

    A new hybrid imaging detector is described that is being developed for the next generation adaptive optics (AO) wavefront sensors. The detector consists of proximity focused microchannel plates (MCPs) read out by pixelated CMOS application specific integrated circuit (ASIC) chips developed at CERN ("Medipix2"). Each Medipix2 pixel has an amplifier, lower and upper charge discriminators, and a 14-bit chounter. The 256x256 array can be read out noiselessly (photon counting) in 286 us. The Medipix2 is buttable on 3 sides to produce 512x(n*256) pixel devices. The readout can be electronically shuttered down to a terporal window of a few microseconds with an accuracy of 10 ns. Good quantum efficiencies can be achieved from the x-ray (open faced with opaque photocathodes) to the optical (sealed tube with multialkali or GaAs photocathode).

  7. Study of the timing performance of micro-channel plate photomultiplier for use as an active layer in a shower maximum detector

    Energy Technology Data Exchange (ETDEWEB)

    Ronzhin, A., E-mail: ronzhin@fnal.gov [Fermilab, Batavia, Il 60510 (United States); Los, S.; Ramberg, E. [Fermilab, Batavia, Il 60510 (United States); Apresyan, A.; Xie, S.; Spiropulu, M. [California Institute of Technology, Pasadena, CA 91126 (United States); Kim, H. [University of Chicago, Chicago, Il 60637 (United States)

    2015-09-21

    We continue the study of micro-channel plate photomultiplier (MCP-PMT) as the active element of a shower maximum (SM) detector. We present test beam results obtained with Photek 240 and Photonis XP85011 MCP-PMTs devices. For proton beams, we obtained a time resolution of 9.6 ps, representing a significant improvement over past results using the same time of flight system. For electron beams, the time resolution obtained for this new type of SM detector is measured to be at the level of 13 ps when we use Photek 240 as the active element of the SM. Using the Photonis XP85011 MCP-PMT as the active element of the SM, we performed time resolution measurements with pixel readout, and achieved a TR better than 30 ps, The pixel readout was observed to improve upon the TR compared to the case where the individual channels were summed.

  8. High-Speed Radiation Tolerant Avalanche Photodiodes Based on InGaN for Space Altimeter Systems Project

    Data.gov (United States)

    National Aeronautics and Space Administration — High-performance, radiation-tolerant detectors are required for the time-of-flight laser based rangefinders. Avalanche photodiodes (APDs) are conventionally chosen...

  9. Ultra-fast time-correlated single photon counting avalanche photodiodes for time-domain non-contact fluorescence diffuse optical tomography

    Science.gov (United States)

    Robichaud, Vincent; Lapointe, Éric; Bérubé-Lauzière, Yves

    2007-06-01

    Recent advances in the design and fabrication of avalanche photodiodes (APDs) and quenching circuits for timecorrelated single photon counting (TCSPC) have made available detectors with timing resolutions comparable to microchannel plate photomultiplier tubes (MCP-PMTs). The latter, were until recently the best TCSPC detectors in terms of temporal resolution (standard electronics fabrication processes in a near future. This will contribute to further decrease their price and ease their integration in complex multi-channel detection systems, as required in diuse optical imaging (DOI) and tomography (DOT). We present, to our knowledge for the first time, results which demonstrate that, despite their small sensitive area, TCSPC APDs can be used in time-domain (TD) DOT and more generally in TD DOI. With appropriate optical design of the detection channel, our experiments show that it is possible to obtain comparable measurements with APDs as with PMTs.

  10. Technological advances in avalanche survival.

    Science.gov (United States)

    Radwin, Martin I; Grissom, Colin K

    2002-01-01

    Over the last decade, a proliferation of interest has emerged in the area of avalanche survival, yielding both an improved understanding of the pathophysiology of death after avalanche burial and technological advances in the development of survival equipment. The dismal survival statistics born out of the modern era of winter recreation unmistakably reveal that elapsed time and depth of burial are the most critical variables of survival and the focus of newer survival devices on the market. Although blunt trauma may kill up to one third of avalanche victims, early asphyxiation is the predominant mechanism of death, and hypothermia is rare. A survival plateau or delay in asphyxiation may be seen in those buried in respiratory communication with an air pocket until a critical accumulation of CO2 or an ice lens develops. The newest survival devices available for adjunctive protection, along with a transceiver and shovel, are the artificial air pocket device (AvaLung), the avalanche air bag system (ABS), and the Avalanche Ball. The artificial air pocket prolongs adequate respiration during snow burial and may improve survival by delaying asphyxiation. The ABS, which forces the wearer to the surface of the avalanche debris by inverse segregation to help prevent burial, has been in use in Europe for the last 10 years with an impressive track record. Finally, the Avalanche Ball is a visual locator device in the form of a spring-loaded ball attached to a tether, which is released from a fanny pack by a rip cord. Despite the excitement surrounding these novel technologies, avalanche avoidance through knowledge and conservative judgment will always be the mainstay of avalanche survival, never to be replaced by any device.

  11. Antimonide-based Geiger-mode avalanche photodiodes for SWIR and MWIR photon counting

    Science.gov (United States)

    Duerr, Erik K.; Manfra, Michael J.; Diagne, Mohamed A.; Bailey, Robert J.; Zayhowski, John J.; Donnelly, Joseph P.; Connors, Michael K.; Grzesik, Michael J.; Turner, George W.

    2010-04-01

    At MIT Lincoln Laboratory, avalanche photodiodes (APDs) have been developed for both 2-μm and 3.4-μm detection using the antimonide material system. These bulk, lattice-matched detectors operate in Geiger mode at temperatures up to 160 K. The 2-μm APDs use a separate-absorber-multiplier design with an InGaAsSb absorber and electron-initiated avalanching in the multiplier. These APDs have exhibited normalized avalanche probability (product of avalanche probability and photo-carrier-injection probability) of 0.4 and dark count rates of ~150 kHz at 77 K for a 30-μm-diameter device. A 1000- element imaging array of the 2-μm detectors has been demonstrated, which operate in a 5 kg dewar with an integrated Stirling-cycle cooler. The APD array is interfaced with a CMOS readout circuit, which provides photon time-of-arrival information for each pixel, allowing the focal plane array to be used in a photon-counting laser radar system. The 3.4-μm APDs use an InAsSb absorber and hole-initiated avalanching and have shown dark count rates of ~500 kHz at 77 K but normalized avalanche probability of < 1%. Research is ongoing to determine the cause of the low avalanche probability and improve the device performance.

  12. Reducing dose in urography while maintaining image quality-a comparison of storage phosphor plates and a flat-panel detector.

    Science.gov (United States)

    Jansson, Margareta; Geijer, Håkan; Persliden, Jan; Andersson, Torbjörn

    2006-01-01

    The introduction of new flat-panel detector technology often forces us to accept too high dose levels as proposed by the manufacturers. We need a tool to compare the image quality of a new system with the accepted standard. The aim of this study was to obtain a comparable image quality for two systems-storage phosphor plates and a flat-panel system using intravenous urography (IVU) as a clinical model. The image quality figure was calculated using a contrast-detail phantom (CDRAD) for the two evaluated systems. This allowed us to set a dose for the flat-panel system that gave equivalent image quality to the storage phosphor plates. This reduced detector dose was used in an evaluation of clinical images to find out if the dose reduction from the phantom study indeed resulted in images of equal clinical image quality. The image quality was assessed using image criteria of the European guidelines for IVU with visual grading analysis. Equivalent image quality in image pairs was achieved at 30% of the dose. The CDRAD contrast-detail phantom makes it possible to find dose levels that give equal image quality using different imaging systems.

  13. Neuronal avalanches and learning

    Energy Technology Data Exchange (ETDEWEB)

    Arcangelis, Lucilla de, E-mail: dearcangelis@na.infn.it [Department of Information Engineering and CNISM, Second University of Naples, 81031 Aversa (Italy)

    2011-05-01

    Networks of living neurons represent one of the most fascinating systems of biology. If the physical and chemical mechanisms at the basis of the functioning of a single neuron are quite well understood, the collective behaviour of a system of many neurons is an extremely intriguing subject. Crucial ingredient of this complex behaviour is the plasticity property of the network, namely the capacity to adapt and evolve depending on the level of activity. This plastic ability is believed, nowadays, to be at the basis of learning and memory in real brains. Spontaneous neuronal activity has recently shown features in common to other complex systems. Experimental data have, in fact, shown that electrical information propagates in a cortex slice via an avalanche mode. These avalanches are characterized by a power law distribution for the size and duration, features found in other problems in the context of the physics of complex systems and successful models have been developed to describe their behaviour. In this contribution we discuss a statistical mechanical model for the complex activity in a neuronal network. The model implements the main physiological properties of living neurons and is able to reproduce recent experimental results. Then, we discuss the learning abilities of this neuronal network. Learning occurs via plastic adaptation of synaptic strengths by a non-uniform negative feedback mechanism. The system is able to learn all the tested rules, in particular the exclusive OR (XOR) and a random rule with three inputs. The learning dynamics exhibits universal features as function of the strength of plastic adaptation. Any rule could be learned provided that the plastic adaptation is sufficiently slow.

  14. Imaging findings of avalanche victims

    Energy Technology Data Exchange (ETDEWEB)

    Grosse, Alexandra B.; Grosse, Claudia A.; Anderson, Suzanne [University Hospital of Berne, Inselspital, Department of Diagnostic, Pediatric and Interventional Radiology, Berne (Switzerland); Steinbach, Lynne S. [University of California San Francisco, Department of Radiology, San Francisco, CA (United States); Zimmermann, Heinz [University Hospital of Berne, Inselspital, Department of Trauma and Emergency Medicine, Berne (Switzerland)

    2007-06-15

    Skiing and hiking outside the boundaries remains an attractive wilderness activity despite the danger of avalanches. Avalanches occur on a relatively frequent basis and may be devastating. Musculoskeletal radiologists should be acquainted with these injuries. Fourteen avalanche victims (11 men and 3 women; age range 17-59 years, mean age 37.4 years) were air transported to a high-grade trauma centre over a period of 2 years. Radiographs, CT and MR images were prospectively evaluated by two observers in consensus. Musculoskeletal findings (61%) were more frequent than extraskeletal findings (39%). Fractures were most commonly seen (36.6%), involving the spine (14.6%) more frequently than the extremities (9.8%). Blunt abdominal and thoracic trauma were the most frequent extraskeletal findings. A wide spectrum of injuries can be found in avalanche victims, ranging from extremity fractures to massive polytrauma. Asphyxia remains the main cause of death along with hypoxic brain injury and hypothermia. (orig.)

  15. Heating of Microchannel Plates Detector Positioned Inside the LHC Beam Pipe by the Electromagnetic Fields of Relativistic Beams

    CERN Document Server

    Dubenskiy, V P; CERN. Geneva; Tsimbal, F A

    1995-01-01

    Here we present the results of our estimates of upper limits for heating induced by the relativistic beams of charged particles at the future LHC in the MCP detector placed inside the beam pipe. The energy losses are small for the uppermost intensities of the beams to be expected: less than 0.0033 Wt for the conductive cromium MCP cladding and not greater than 0.02 Wt for the dialectric MCP body (for the whole MCP disk of 100 sq.cm area). The special measurements of the dispersion law e(w) of the MCP dialectric material have been performed in order to get the reference data to the analytical calculations. The approaches outlined here could be applied to any detector positioned in the vicinity of the beams. The possible problems of the beam induced electrical signal in the detector circuits are touched also.

  16. Surface and buildup region dose measurements with Markus parallel-plate ionization chamber, Gafchromic EBT3 film and MOSFET detector for high energy photon beams

    CERN Document Server

    Akbas, Ugur; Koksal, Canan; Bilge, Hatice

    2016-01-01

    The aim of the study was to investigate surface and buildup region doses for 6 MV photon beams using a Markus parallel-plate ionization chamber, GafChromic EBT3 film and MOSFET detector for different field sizes and beam angles. The measurements were made in a water equivalent solid phantom at the surface and in the buildup region of the 6 MV photon beams at 100 cm source-detector distance (SDD) for 5x5, 10x10 and 20x20 cm2 field sizes and 0, 30, 60, 80 and 90 beam angles. The surface doses for 10x10 cm2 field size were found to be 20.33%, 18.80% and 25.48% for Markus chamber, EBT3 film and MOSFET detector, respectively. The surface dose increased with field size for all dosimeters. As the angle of the incident radiation beam became more oblique, the surface dose increased. The effective measurement depths of dosimeters vary, thus the results of the measurements could be different. This issue can lead to mistakes at surface and buildup dosimetry, and must be taken into account.

  17. Automated characterization of single-photon avalanche photodiode

    CERN Document Server

    Ghazali, Aina M M; Sauge, Sebastien; Makarov, Vadim

    2012-01-01

    We report an automated characterization of a single-photon detector based on commercial silicon avalanche photodiode (PerkinElmer C30902SH). The photodiode is characterized by I-V curves at different illumination levels (darkness, 10 pW and 10 uW), dark count rate and photon detection efficiency at different bias voltages. The automated characterization routine is implemented in C++ running on a Linux computer.

  18. Surface and Buildup Region Dose Measurements with Markus Parallel-Plate Ionization Chamber, GafChromic EBT3 Film, and MOSFET Detector for High-Energy Photon Beams

    Directory of Open Access Journals (Sweden)

    Ugur Akbas

    2016-01-01

    Full Text Available The aim of the study was to investigate surface and buildup region doses for 6 MV and 15 MV photon beams using a Markus parallel-plate ionization chamber, GafChromic EBT3 film, and MOSFET detector for different field sizes and beam angles. The measurements were made in a water equivalent solid phantom at the surface and in the buildup region of the 6 MV and 15 MV photon beams at 100 cm source-detector distance for 5 × 5, 10 × 10, and 20 × 20 cm2 field sizes and 0°, 30°, 60°, and 80° beam angles. The surface doses using 6 MV photon beams for 10 × 10 cm2 field size were found to be 20.3%, 18.8%, and 25.5% for Markus chamber, EBT3 film, and MOSFET detector, respectively. The surface doses using 15 MV photon beams for 10 × 10 cm2 field size were found to be 14.9%, 13.4%, and 16.4% for Markus chamber, EBT3 film, and MOSFET detector, respectively. The surface dose increased with field size for all dosimeters. As the angle of the incident radiation beam became more oblique, the surface dose increased. The effective measurement depths of dosimeters vary; thus, the results of the measurements could be different. This issue can lead to mistakes at surface and buildup dosimetry and must be taken into account.

  19. An X-ray scanner prototype based on a novel hybrid gaseous detector

    CERN Document Server

    Iacobaeus, C; Lund-Jensen, B; Peskov, Vladimir

    2007-01-01

    We have developed a prototype of a new type of hybrid X-ray detector. It contains a thin wall (few μm) edge- illuminated lead glass capillary plate (acting as a converter of X-rays photons to primary electrons) combined with a microgap parallel-plate avalanche chamber operating in various gas mixtures at 1 atm. The operation of these converters was studied in a wide range of X-ray energies (from 6 to 60 keV) at incident angles varying from 0° to 90°. The detection efficiency, depending on the geometry, photon's energy, incident angle and the mode of operation, was between a few and 40%. The position resolution achieved was 50 μm in digital form and was practically independent of the photon's energy or gas mixture. The developed detector may open new possibilities for medical imaging, for example in mammography, portal imaging, radiography (including security devices), crystallography and many other applications.

  20. Avalanche effects near nanojunctions

    Science.gov (United States)

    Nandigana, Vishal V. R.; Aluru, N. R.

    2016-07-01

    In this article, we perform a computational investigation of a nanopore connected to external fluidic reservoirs of asymmetric geometries. The asymmetry between the reservoirs is achieved by changing the cross-sectional areas, and the reservoirs are designated as the micropore reservoir and macropore reservoir. When an electric field is applied, which is directed from the macropore towards the micropore reservoir, we observe local nonequilibrium chaotic current oscillations. The current oscillations originate at the micropore-nanopore interface owing to the local cascade of ions; we refer to this phenomenon as the "avalanche effects." We mathematically quantify chaos in terms of the maximum Lyapunov exponent. The maximum Lyapunov exponent exhibits a monotonic increase with the applied voltage and the macropore reservoir diameter. The temporal power spectra maps of the chaotic currents depict a low-frequency "1 /f "-type dynamics for the voltage chaos and "1 /f2 "-type dynamics for the macropore reservoir chaos. The results presented here offer avenues to manipulate ionic diodes and fluidic pumps.

  1. Ultraviolet avalanche photodiodes

    Science.gov (United States)

    McClintock, Ryan; Razeghi, Manijeh

    2015-08-01

    The III-Nitride material system is rapidly maturing; having proved itself as a material for LEDs and laser, and now finding use in the area of UV photodetectors. However, many UV applications are still dominated by the use of photomultiplier tubes (PMT). PMTs are capable of obtaining very high sensitivity using internal electron multiplication gain (typically ~106). It is highly desirable to develop a compact semiconductor-based photodetector capable of realizing this level of sensitivity. In principle, this can be obtained in III-Nitrides by taking advantage of avalanche multiplication under high electric fields - typically 2.7 MV/cm, which with proper design can correspond to an external reverse bias of less than 100 volts. In this talk, we review the current state-of-the-art in III-Nitride solar- and visible-blind APDs, and present our latest results on GaN APDs grown on both conventional sapphire and low dislocation density free-standing c- and m-plane GaN substrates. Leakage current, gain, and single photon detection efficiency (SPDE) of these APDs were compared. The spectral response and Geiger-mode photon counting performance of UV APDs are studied under low photon fluxes, with single photon detection capabilities as much as 30% being demonstrated in smaller devices. Geiger-mode operation conditions are optimized for enhanced SPDE.

  2. Photon counting modules using RCA silicon avalanche photodiodes

    Science.gov (United States)

    Lightstone, Alexander W.; Macgregor, Andrew D.; Macsween, Darlene E.; Mcintyre, Robert J.; Trottier, Claude; Webb, Paul P.

    1989-01-01

    Avalanche photodiodes (APD) are excellent small area, solid state detectors for photon counting. Performance possibilities include: photon detection efficiency in excess of 50 percent; wavelength response from 400 to 1000 nm; count rate to 10 (exp 7) counts per sec; afterpulsing at negligible levels; timing resolution better than 1 ns. Unfortunately, these performance levels are not simultaneously available in a single detector amplifier configuration. By considering theoretical performance predictions and previous and new measurements of APD performance, the anticipated performance of a range of proposed APD-based photon counting modules is derived.

  3. Gamma-ray detection efficiency of the microchannel plate installed as an ion detector in the low energy particle instrument onboard the GEOTAIL satellite.

    Science.gov (United States)

    Tanaka, Y T; Yoshikawa, I; Yoshioka, K; Terasawa, T; Saito, Y; Mukai, T

    2007-03-01

    A microchannel plate (MCP) assembly has been used as an ion detector in the low energy particle (LEP) instrument onboard the magnetospheric satellite GEOTAIL. Recently the MCP assembly has detected gamma rays emitted from an astronomical object and has been shown to provide unique information of gamma rays if they are intense enough. However, the detection efficiency for gamma rays was not measured before launch, and therefore we could not analyze the LEP data quantitatively. In this article, we report the gamma-ray detection efficiency of the MCP assembly. The measured efficiencies are 1.29%+/-0.71% and 0.21%+/-0.14% for normal incidence 60 and 662 keV gamma rays, respectively. The incident angle dependence is also presented. Our calibration is crucial to study high energy astrophysical phenomena by using the LEP.

  4. Avalanche risk assessment in Russia

    Science.gov (United States)

    Komarov, Anton; Seliverstov, Yury; Sokratov, Sergey; Glazovskaya, Tatiana; Turchaniniva, Alla

    2017-04-01

    The avalanche prone area covers about 3 million square kilometers or 18% of total area of Russia and pose a significant problem in most mountain regions of the country. The constant growth of economic activity, especially in the North Caucasus region and therefore the increased avalanche hazard lead to the demand of the large-scale avalanche risk assessment methods development. Such methods are needed for the determination of appropriate avalanche protection measures as well as for economic assessments during all stages of spatial planning of the territory. The requirement of natural hazard risk assessments is determined by the Federal Law of Russian Federation. However, Russian Guidelines (SP 11-103-97; SP 47.13330.2012) are not clearly presented concerning avalanche risk assessment calculations. A great size of Russia territory, vast diversity of natural conditions and large variations in type and level of economic development of different regions cause significant variations in avalanche risk values. At the first stage of research the small scale avalanche risk assessment was performed in order to identify the most common patterns of risk situations and to calculate full social risk and individual risk. The full social avalanche risk for the territory of country was estimated at 91 victims. The area of territory with individual risk values lesser then 1×10(-6) covers more than 92 % of mountain areas of the country. Within these territories the safety of population can be achieved mainly by organizational activities. Approximately 7% of mountain areas have 1×10(-6) - 1×10(-4) individual risk values and require specific mitigation measures to protect people and infrastructure. Territories with individual risk values 1×10(-4) and above covers about 0,1 % of the territory and include the most severe and hazardous mountain areas. The whole specter of mitigation measures is required in order to minimize risk. The future development of such areas is not recommended

  5. Improved x-ray detection and particle identification with avalanche photodiodes.

    Science.gov (United States)

    Diepold, Marc; Fernandes, Luis M P; Machado, Jorge; Amaro, Pedro; Abdou-Ahmed, Marwan; Amaro, Fernando D; Antognini, Aldo; Biraben, François; Chen, Tzu-Ling; Covita, Daniel S; Dax, Andreas J; Franke, Beatrice; Galtier, Sandrine; Gouvea, Andrea L; Götzfried, Johannes; Graf, Thomas; Hänsch, Theodor W; Hildebrandt, Malte; Indelicato, Paul; Julien, Lucile; Kirch, Klaus; Knecht, Andreas; Kottmann, Franz; Krauth, Julian J; Liu, Yi-Wei; Monteiro, Cristina M B; Mulhauser, Françoise; Naar, Boris; Nebel, Tobias; Nez, François; Santos, José Paulo; dos Santos, Joaquim M F; Schuhmann, Karsten; Szabo, Csilla I; Taqqu, David; Veloso, João F C A; Voss, Andreas; Weichelt, Birgit; Pohl, Randolf

    2015-05-01

    Avalanche photodiodes are commonly used as detectors for low energy x-rays. In this work, we report on a fitting technique used to account for different detector responses resulting from photoabsorption in the various avalanche photodiode layers. The use of this technique results in an improvement of the energy resolution at 8.2 keV by up to a factor of 2 and corrects the timing information by up to 25 ns to account for space dependent electron drift time. In addition, this waveform analysis is used for particle identification, e.g., to distinguish between x-rays and MeV electrons in our experiment.

  6. Improved x-ray detection and particle identification with avalanche photodiodes

    Energy Technology Data Exchange (ETDEWEB)

    Diepold, Marc, E-mail: marc.diepold@mpq.mpg.de; Franke, Beatrice; Götzfried, Johannes; Hänsch, Theodor W.; Krauth, Julian J.; Mulhauser, Françoise; Nebel, Tobias; Pohl, Randolf [Max Planck Institute of Quantum Optics, 85748 Garching (Germany); Fernandes, Luis M. P.; Amaro, Fernando D.; Gouvea, Andrea L.; Monteiro, Cristina M. B.; Santos, Joaquim M. F. dos [LIBPhys, Physics Department, Universidade de Coimbra, 3004-516 Coimbra (Portugal); Machado, Jorge [Laboratório de Instrumentação, Engenharia Biomédica e Física da Radiação (LIBPhys-UNL) e Departamento de Física da Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa, Monte da Caparica, 2892-516 Caparica (Portugal); Laboratoire Kastler Brossel, UPMC-Sorbonne Universités, CNRS, ENS-PSL Research University, Collège de France, 4 place Jussieu, case 74, 75005 Paris (France); Amaro, Pedro; Santos, José Paulo [Laboratório de Instrumentação, Engenharia Biomédica e Física da Radiação (LIBPhys-UNL) e Departamento de Física da Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa, Monte da Caparica, 2892-516 Caparica (Portugal); and others

    2015-05-15

    Avalanche photodiodes are commonly used as detectors for low energy x-rays. In this work, we report on a fitting technique used to account for different detector responses resulting from photoabsorption in the various avalanche photodiode layers. The use of this technique results in an improvement of the energy resolution at 8.2 keV by up to a factor of 2 and corrects the timing information by up to 25 ns to account for space dependent electron drift time. In addition, this waveform analysis is used for particle identification, e.g., to distinguish between x-rays and MeV electrons in our experiment.

  7. Observations and modelling of snow avalanche entrainment

    OpenAIRE

    2002-01-01

    In this paper full scale avalanche dynamics measurements from the Italian Pizzac and Swiss Vallée de la Sionne test sites are used to develop a snowcover entrainment model. A detailed analysis of three avalanche events shows that snowcover entrainment at the avalanche front appears to dominate over bed erosion at the basal sliding surface. Furthermore, the distribution of mass within the avalanche body is primarily a function of basal fric...

  8. Correcting for accidental correlations in saturated avalanche photodiodes.

    Science.gov (United States)

    Grieve, J A; Chandrasekara, R; Tang, Z; Cheng, C; Ling, A

    2016-02-22

    In this paper we present a general method for estimating rates of accidental coincidence between a pair of single photon detectors operated within their saturation regimes. By folding the effects of recovery time of both detectors and the detection circuit into an "effective duty cycle" we are able to accomodate complex recovery behaviour at high event rates. As an example, we provide a detailed high-level model for the behaviour of passively quenched avalanche photodiodes, and demonstrate effective background subtraction at rates commonly associated with detector saturation. We show that by post-processing using the updated model, we observe an improvement in polarization correlation visibility from 88.7% to 96.9% in our experimental dataset. This technique will be useful in improving the signal-to-noise ratio in applications which depend on coincidence measurements, especially in situations where rapid changes in flux may cause detector saturation.

  9. High-density avalanche chambers for positron emission tomography

    Energy Technology Data Exchange (ETDEWEB)

    Manfrass, P.; Enghardt, W.; Fromm, W.D.; Wohlfarth, D.; Hohmuth, K.

    1988-12-15

    A positron tomograph for radiopharmaceutical and medical research is under construction. In its final stage it will cover six high-density avalanche chambers (HIDAC) in a hexagonal arrangement. Each detector with a sensitive area of 50x28 cm/sup 2/ will consist of a stack of four pairs of multihole photon-to-electron converters with a multiwire proportional counter (MWPC) in between. An experimental investigation of detector properties as time and spatial resolutions as well as detector efficiency in dependence to converter structure, electric field strength and counting gas mixture preceded the final design of these detectors. Results of these studies are outlined. Furthermore, longitudinal tomograms taken with a stationary test camera are presented.

  10. Correlations in avalanche critical points

    Science.gov (United States)

    Cerruti, Benedetta; Vives, Eduard

    2009-07-01

    Avalanche dynamics and related power-law statistics are ubiquitous in nature, arising in phenomena such as earthquakes, forest fires, and solar flares. Very interestingly, an analogous behavior is associated with many condensed-matter systems, such as ferromagnets and martensites. Bearing it in mind, we study the prototypical random-field Ising model at T=0 . We find a finite correlation between waiting intervals and the previous avalanche size. This correlation is not found in other models for avalanches but it is experimentally found in earthquakes and in forest fires. Our study suggests that this effect occurs in critical points that are at the end of a first-order discontinuity separating two regimes: one with high activity from another with low activity.

  11. Automated Characterization of Single-Photon Avalanche Photodiode

    Directory of Open Access Journals (Sweden)

    Aina Mardhiyah M. Ghazali

    2012-01-01

    Full Text Available We report an automated characterization of a single-photon detector based on commercial silicon avalanche photodiode (PerkinElmer C30902SH. The photodiode is characterized by I-V curves at different illumination levels (darkness, 10 pW and 10 µW, dark count rate and photon detection efficiency at different bias voltages. The automated characterization routine is implemented in C++ running on a Linux computer. ABSTRAK: Kami melaporkan pencirian pengesan foton tunggal secara automatik berdasarkan kepada diod foto runtuhan silikon (silicon avalanche photodiode (PerkinElmer C30902SH komersial. Pencirian  diod foto adalah berdasarkan kepada plot arus-voltan (I-V pada tahap pencahayaan yang berbeza (kelam - tanpa cahaya, 10pW, dan 10µW, kadar bacaan latar belakang, kecekapan pengesanan foton pada voltan picuan yang berbeza. Pengaturcaraan C++ digunakan di dalam rutin pencirian automatik melalui komputer dengan sistem pengendalian LINUX.KEYWORDS: avalanche photodiode (APD; single photon detector; photon counting; experiment automation

  12. Spreading and Deposit Characteristics of a Rapid Dry Granular Avalanche Across 3D Topography: Experimental Study

    Science.gov (United States)

    Wang, Yu-Feng; Xu, Qiang; Cheng, Qian-Gong; Li, Yan; Luo, Zhong-Xu

    2016-11-01

    Aiming to understand the propagation and deposit behaviours of a granular avalanche along a 3D complex basal terrain, a new 3D experimental platform in 1/400 scale was developed according to the natural terrain of the Xiejiadianzi rock avalanche, with a series of laboratory experiments being conducted. Through the conduction of these tests, parameters, including the morphological evolution of sliding mass, run-outs and velocities of surficial particles, thickness contour and centre of final deposit, equivalent frictional coefficient, and energy dissipation, are documented and analysed, with the geomorphic control effect, material grain size effect, drop angle effect, and drop distance effect on rock avalanche mobility being discussed primarily. From the study, some interesting conclusions for a better understanding of rock avalanche along a 3D complex basal topography are reached. (1) For the granular avalanche tested in this study, great differences between the evolutions of the debris along the right and left branch valleys were observed, with an obvious geomorphic control effect on avalanche mobility presented. In addition, some other interesting features, including groove-like trough and superelevation, were also observed under the control of the topographic interferences. (2) The equivalent frictional coefficients of the granular avalanches tested here range from 0.48 to 0.57, which is lower than that reached with a set-up composed of an inclined chute and horizontal plate and higher than that reached using a set-up composed of only an inclined chute. And the higher the drop angle and fine particle content, the higher the equivalent frictional coefficient. The effect of drop distance on avalanche mobility is minor. (3) For a granular avalanche, momentum transfer plays an important role in the motion of mass, which can accelerate the mobility of the front part greatly through delivering the kinetic energy of the rear part to the front.

  13. Lumped transmission line avalanche pulser

    Science.gov (United States)

    Booth, Rex

    1995-01-01

    A lumped linear avalanche transistor pulse generator utilizes stacked transistors in parallel within a stage and couples a plurality of said stages, in series with increasing zener diode limited voltages per stage and decreasing balanced capacitance load per stage to yield a high voltage, high and constant current, very short pulse.

  14. Avalanche dynamics on a rough inclined plane.

    Science.gov (United States)

    Börzsönyi, Tamás; Halsey, Thomas C; Ecke, Robert E

    2008-07-01

    The avalanche behavior of gravitationally forced granular layers on a rough inclined plane is investigated experimentally for different materials and for a variety of grain shapes ranging from spherical beads to highly anisotropic particles with dendritic shape. We measure the front velocity, area, and height of many avalanches and correlate the motion with the area and height. We also measure the avalanche profiles for several example cases. As the shape irregularity of the grains is increased, there is a dramatic qualitative change in avalanche properties. For rough nonspherical grains, avalanches are faster, bigger, and overturning in the sense that individual particles have down-slope speeds u p that exceed the front speed uf as compared with avalanches of spherical glass beads that are quantitatively slower and smaller and where particles always travel slower than the front speed. There is a linear increase of three quantities: (i) dimensionless avalanche height, (ii) ratio of particle to front speed, and (iii) the growth rate of avalanche speed with increasing avalanche size with increasing tan theta r where theta r is the bulk angle of repose, or with increasing beta P, the slope of the depth averaged flow rule, where both theta r and beta P reflect the grain shape irregularity. These relations provide a tool for predicting important dynamical properties of avalanches as a function of grain shape irregularity. A relatively simple depth-averaged theoretical description captures some important elements of the avalanche motion, notably the existence of two regimes of this motion.

  15. Simulation of space charge effects in resistive plate chambers

    CERN Document Server

    Lippmann, Christian

    2003-01-01

    Multigap resistive plate chambers with 0.3-mm gas gaps operated in avalanche mode at atmospheric pressure have reached timing accuracies below 50 ps (standard deviation) with efficiencies above 99% . The avalanches in high homogeneous electric fields of 100 kV/cm are strongly influenced by space charge effects which are the main topic of this paper. We extend a previously discussed Monte Carlo simulation model of avalanches in resistive plate chambers by the dynamic calculation of the electric field in the avalanches. We complete the previously presented results on time resolution and efficiency data with simulated charge spectra. The simulated data shows good agreement with measurements. The detailed simulation of the avalanche saturation due to the space charge fields explains the small observed charges, the shape of the spectra, and the linear increase of average charges with high voltage. (22 refs).

  16. Radiation Response of Emerging High Gain, Low Noise Detectors

    Science.gov (United States)

    Becker, Heidi N.; Farr, William H; Zhu, David Q.

    2007-01-01

    Data illustrating the radiation response of emerging high gain, low noise detectors are presented. Ionizing dose testing of silicon internal discrete avalanche photodiodes, and 51-MeV proton testing of InGaAs/InAlAs avalanche photodiodes operated in Geiger mode are discussed.

  17. STUDY ON SIMULATION METHOD OF AVALANCHE : FLOW ANALYSIS OF AVALANCHE USING PARTICLE METHOD

    OpenAIRE

    2015-01-01

    In this paper, modeling for the simulation of the avalanche by a particle method is discussed. There are two kinds of the snow avalanches, one is the surface avalanche which shows a smoke-like flow, and another is the total-layer avalanche which shows a flow like Bingham fluid. In the simulation of the surface avalanche, the particle method in consideration of a rotation resistance model is used. The particle method by Bingham fluid is used in the simulation of the total-layer avalanche. At t...

  18. Practical photon number detection with electric field-modulated silicon avalanche photodiodes.

    Science.gov (United States)

    Thomas, O; Yuan, Z L; Shields, A J

    2012-01-24

    Low-noise single-photon detection is a prerequisite for quantum information processing using photonic qubits. In particular, detectors that are able to accurately resolve the number of photons in an incident light pulse will find application in functions such as quantum teleportation and linear optics quantum computing. More generally, such a detector will allow the advantages of quantum light detection to be extended to stronger optical signals, permitting optical measurements limited only by fluctuations in the photon number of the source. Here we demonstrate a practical high-speed device, which allows the signals arising from multiple photon-induced avalanches to be precisely discriminated. We use a type of silicon avalanche photodiode in which the lateral electric field profile is strongly modulated in order to realize a spatially multiplexed detector. Clearly discerned multiphoton signals are obtained by applying sub-nanosecond voltage gates in order to restrict the detector current.

  19. The blocking probability of Geiger-mode avalanche photo-diodes

    Science.gov (United States)

    Moision, Bruce; Srinivasan, Meera; Hamkins, Jon

    2005-01-01

    When a photo is detected by a Geiger-mode avalanche photo-diode (GMAPD), the detector is rendered inactive, or blocked, for a certain period of time. In this paper we derive the blocking probability for a GMAPD whose input is either an unmodulated, Benoulli modulated or pulse-position-modulated Poisson process.

  20. Geiger-Mode Avalanche Photodiode Arrays Integrated to All-Digital CMOS Circuits.

    Science.gov (United States)

    Aull, Brian

    2016-04-08

    This article reviews MIT Lincoln Laboratory's work over the past 20 years to develop photon-sensitive image sensors based on arrays of silicon Geiger-mode avalanche photodiodes. Integration of these detectors to all-digital CMOS readout circuits enable exquisitely sensitive solid-state imagers for lidar, wavefront sensing, and passive imaging.

  1. Photon Detection with Cooled Avalanche Photodiodes: Theory and Preliminary Experimental Results

    Science.gov (United States)

    Robinson, D. L.; Hays, D. A.

    1985-01-01

    Avalanche photodiodes (APDs) can be operated in a geiger-tube mode so that they can respond to single electron events and thus be used as photon counting detectors. Operational characteristics and theory of APDs while used in this mode are analyzed and assessed. Preliminary experimental investigation of several commercially available APDs has commenced, and initial results for dark count statistics are presented.

  2. Geiger-Mode Avalanche Photodiode Arrays Integrated to All-Digital CMOS Circuits

    Directory of Open Access Journals (Sweden)

    Brian Aull

    2016-04-01

    Full Text Available This article reviews MIT Lincoln Laboratory's work over the past 20 years to develop photon-sensitive image sensors based on arrays of silicon Geiger-mode avalanche photodiodes. Integration of these detectors to all-digital CMOS readout circuits enable exquisitely sensitive solid-state imagers for lidar, wavefront sensing, and passive imaging.

  3. Geiger-Mode Avalanche Photodiode Arrays Integrated to All-Digital CMOS Circuits

    OpenAIRE

    Brian Aull

    2016-01-01

    This article reviews MIT Lincoln Laboratory's work over the past 20 years to develop photon-sensitive image sensors based on arrays of silicon Geiger-mode avalanche photodiodes. Integration of these detectors to all-digital CMOS readout circuits enable exquisitely sensitive solid-state imagers for lidar, wavefront sensing, and passive imaging.

  4. Two-dimensional electronic readout system for multi-step-avalanche chambers

    NARCIS (Netherlands)

    Carlén, L.; Garpmann, S.; Gustafsson, H.-A.; Löhner, H.; Nystrand, J.; Oskarsson, A.; Otterlund, I.; Svensson, T.; Stenlund, E.; Söderström, K.; Whitlow, H.J.

    1997-01-01

    We present prototype studies of a new technical solution of detector readout for measurements of charged particles at very high particle densities. In particular, this paper describes a readout system for Multi-Step Avalanche Chambers designed for the WA98 experiment at the CERN SPS. Results from th

  5. Cosmic Ray Measurements by Scintillators with Metal Resistor Semiconductor Avalanche Photo Diodes

    Science.gov (United States)

    Blanco, Francesco; La Rocca, Paola; Riggi, Francesco; Akindinov, Alexandre; Mal'kevich, Dmitry

    2008-01-01

    An educational set-up for cosmic ray physics experiments is described. The detector is based on scintillator tiles with a readout through metal resistor semiconductor (MRS) avalanche photo diode (APD) arrays. Typical measurements of the cosmic angular distribution at sea level and a study of the East-West asymmetry obtained by such a device are…

  6. A new single-photon avalanche diode in 90nm standard CMOS technology

    NARCIS (Netherlands)

    Karami, M.A.; Gersbach, M.; Charbon, E.

    2010-01-01

    A single-photon avalanche diode (SPAD) fabricated in a 90nm standard CMOS process is reported. The detector comprises an octagonal multiplication region and a guard ring to prevent premature edge breakdown using exclusively standard layers. The proposed structure is the result of a systematic study

  7. Cosmic Ray Measurements by Scintillators with Metal Resistor Semiconductor Avalanche Photo Diodes

    Science.gov (United States)

    Blanco, Francesco; La Rocca, Paola; Riggi, Francesco; Akindinov, Alexandre; Mal'kevich, Dmitry

    2008-01-01

    An educational set-up for cosmic ray physics experiments is described. The detector is based on scintillator tiles with a readout through metal resistor semiconductor (MRS) avalanche photo diode (APD) arrays. Typical measurements of the cosmic angular distribution at sea level and a study of the East-West asymmetry obtained by such a device are…

  8. Self-aligned multi-channel superconducting nanowire avalanche photodetector

    CERN Document Server

    Cheng, Risheng; Ma, Xiaosong; Fan, Linran; Fong, King Y; Poot, Menno; Tang, Hong X

    2016-01-01

    We describe a micromachining process to allow the coupling of an array of single-mode telecommunication fibers to individual superconducting nanowire single photon detectors (SNSPDs). As proof of principle, we show the integration of four detectors on the same silicon chip, including two standard single-section nanowire detectors and two superconducting nanowire avalanche photodetectors (SNAPs) with modified series structure without external inductor, and their performances are compared. The SNAP shows saturated system detection efficiency of 16% while the dark count rate is less than 20 Hz, without the use of photon-recycling reflectors. The SNAP also demonstrates doubled signal-to-noise ratio, reduced reset time (~ 4.9 ns decay time) and improved timing jitter (62 ps FWHM) compared to standard SNSPDs.

  9. Avalanche hazard and control in Kazakhstan

    Directory of Open Access Journals (Sweden)

    V. P. Blagoveshchensky

    2014-01-01

    Full Text Available In Kazakhstan, area of 124 thousand km2 is prone to the avalanche hazard. Avalanches are released down in mountain regions situated along the eastern boundary of Kazakhstan. Systematic studies of avalanches here were started in 1958 by explorer I.S. Sosedov; later on, I.V. Seversky continued these investigations in Institute of Geography of the Kazakh Soviet Republic. Actually, he founded the Kazakh school of the avalanche studies. In 1970–1980s, five snow-avalanche stations operated in Kazakhstan: two in Il’ Alatau, two in Zhetysu Alatau, and one in the Altai. At the present time, only two stations and two snow-avalanche posts operate, and all of them are located in Il’ Alatau.Since 1951 to 2013, 75 avalanches took place in Kazakhstan, releases of them caused significant damages. For this period 172 people happened to be under avalanches, among them 86 perished. Large avalanche catastrophes causing human victims and destructions took place in Altai in 1977 and in Karatau in 1990. In spring of 1966, only in Il’ Alatau avalanches destroyed more 600 ha of mature fir (coniferous forest, and the total area of forest destroyed here by avalanches amounts to 2677 ha or 7% of the total forest area.For 48 years of the avalanche observations, there were 15 winters with increased avalanche activity in the river Almatinka basin when total volume of released snow exceeded annual mean value of 147 thousand m3. During this period, number of days with winter avalanches changed from three (in season of 1973/1974 to 28 (1986/1987, the average for a year is 16 days for a season. Winter with the total volume of snow 1300 thousand m3 occur once in 150 years. Individual avalanches with maximal volume of 350 thousand m3 happen once in 80 years.Preventive avalanche releases aimed at protection of roads and settlements are used in Kazakhstan since 1974. These precautions are taken in Il’ Alatau, Altai, and on Kalbinsky Range. Avalanches are released with the

  10. X-ray spectrometry with Peltier-cooled large area avalanche photodiodes

    Energy Technology Data Exchange (ETDEWEB)

    Fernandes, L.M.P.; Lopes, J.A.M.; Santos, J.M.F. dos E-mail: jmf@gian.fis.uc.pt; Conde, C.A.N

    2004-01-01

    Performance characteristics of the response of a Peltier-cooled large-area avalanche photodiode are investigated. Detector gain, energy linearity, energy resolution and minimum detectable energy are studied at different operation temperatures. Detector energy resolution and lowest detectable X-ray energy present a strong improvement as the operation temperature is reduced from 25 to 15 deg. C and slower improvements are achieved for temperatures below 10 deg. C.

  11. A 4-Channel Waveform Sampling ASIC in 0.13 μm CMOS for front-end Readout of Large-Area Micro-Channel Plate Detectors

    Science.gov (United States)

    Oberla, E.; Grabas, H.; Bogdan, M.; Frisch, H.; Genat, J. F.; Nishimura, K.; Varner, G.; Wong, A.

    We describe here the development of PSEC-3, a custom integrated circuit designed in the IBM-8RF 0.13 μm CMOS process and intended for fast, low-power waveform sampling. As part of the Large-Area Picosecond Photo-Detector (LAPPD) collaboration, this chip has been designed as a prototype application-specific integrated circuit (ASIC) for the front-end transmission line readout of large-area micro-channel plate photomultiplier tubes (MCP-PMTs). With 4 channels, PSEC-3 has a buffer depth of 256 samples on each channel, a chip-parallel ramp-compare ADC, and a serial data readout that includes the capability for region-of-interest windowing to reduce dead time. Chip calibrations and performance results, including achieved sampling rates of 2.5-17 GSa/s, are reported. Some design issues are identified, in particular the dependence of analog bandwidth on location in the sampling array. The causes have been found and addressed in a subsequent PSEC-4 submission.

  12. Silicon avalanche photodiodes for direct detection of X-rays.

    Science.gov (United States)

    Baron, Alfred Q R; Kishimoto, Shunji; Morse, John; Rigal, Jean Marie

    2006-03-01

    Silicon avalanche photodiodes (APDs) are discussed as fast X-ray detectors for synchrotron radiation. The emphasis is on ;direct' detection, where the X-ray is absorbed within the silicon APD itself, and, therefore, on use with medium-energy X-rays, <30 keV. The impact of APD structure on device performance is examined, and representative data from many different commercial devices are presented. Specific areas discussed include signal shapes, high-rate behavior, time resolution and pulse-height response. Data from several APD arrays are also presented, as is a detailed description of an integrated package system. Tables are included comparing commercially available devices, including arrays.

  13. Readout of a scintillating-fiber array by avalanche photodiodes

    CERN Document Server

    Okusawa, T; Yamasaki, M; Yoshida, T

    2000-01-01

    We have evaluated the performance of avalanche photodiodes (APDs) as photosensors for scintillating-fiber tracking detectors, putting emphasis on their temperature dependence. For this purpose, a scintillating-fiber array has been built with 0.5 mm diameter fibers 55 cm long. The array is so structured that an incident particle traverses two fibers coupled to an APD. As temperature of the APD falls, the signal-to-noise (S/N) ratio rises exponentially. It even reaches 90 at -30 deg. C. The detection efficiency exceeds 98% when the temperature decreases until the S/N ratio becomes 30.

  14. Double Screening Tests of the CMS ECAL Avalanche Photodiodes

    CERN Document Server

    Deiters, Konrad; Renker, Dieter; Sakhelashvili, Tariel; Britvitch, Ilia; Kuznetsov, Andrey; Musienko, Yuri; Singovsky, Alexander

    2005-01-01

    Specially developed avalanche photo-diodes (APDs) will be used to measure the light from the 61,200 lead tungstate crystals in the barrel part of the CMS electromagnetic calorimeter. To ensure the reliability over the lifetime of the detector, every APD is screened by irradiation and burn-in before it is accepted for CMS. As part of the establishment of the screening procedure and to determine its effectiveness, a large number of APDs were screened twice. The results of these tests suggest that the required reliability will be achieved.

  15. The prehospital management of avalanche victims.

    Science.gov (United States)

    Kornhall, Daniel K; Martens-Nielsen, Julie

    2016-12-01

    Avalanche accidents are frequently lethal events with an overall mortality of 23%. Mortality increases dramatically to 50% in instances of complete burial. With modern day dense networks of ambulance services and rescue helicopters, health workers often become involved during the early stages of avalanche rescue. Historically, some of the most devastating avalanche accidents have involved military personnel. Armed forces are frequently deployed to mountain regions in order to train for mountain warfare or as part of ongoing conflicts. Furthermore, military units are frequently called to assist civilian organised rescue in avalanche rescue operations. It is therefore important that clinicians associated with units operating in mountain regions have an understanding of, the medical management of avalanche victims, and of the preceding rescue phase. The ensuing review of the available literature aims to describe the pathophysiology particular to avalanche victims and to outline a structured approach to the search, rescue and prehospital medical management.

  16. Avalanche ecology and large magnitude avalanche events: Glacier National Park, Montana, USA

    Science.gov (United States)

    Fagre, Daniel B.; Peitzsch, Erich H.

    2010-01-01

    Large magnitude snow avalanches play an important role ecologically in terms of wildlife habitat, vegetation diversity, and sediment transport within a watershed. Ecological effects from these infrequent avalanches can last for decades. Understanding the frequency of such large magnitude avalanches is also critical to avalanche forecasting for the Going-to-the-Sun Road (GTSR). In January 2009, a large magnitude avalanche cycle occurred in and around Glacier National Park, Montana. The study site is the Little Granite avalanche path located along the GTSR. The study is designed to quantify change in vegetative cover immediately after a large magnitude event and document ecological response over a multi-year period. GPS field mapping was completed to determine the redefined perimeter of the avalanche path. Vegetation was inventoried using modified U.S. Forest Service Forest Inventory and Analysis plots, cross sections were taken from over 100 dead trees throughout the avalanche path, and an avalanche chronology was developed. Initial results indicate that the perimeter of this path was expanded by 30%. The avalanche travelled approximately 1200 vertical meters and 3 linear kilometers. Stands of large conifers as old as 150 years were decimated by the avalanche, causing a shift in dominant vegetation types in many parts of the avalanche path. Woody debris is a major ground cover up to 3 m in depth on lower portions of the avalanche path and will likely affect tree regrowth. Monitoring and measuring the post-avalanche vegetation recovery of this particular avalanche path provides a unique dataset for determining the ecological role of avalanches in mountain landscapes.

  17. The 10 Tesla muSR instrument: detector solutions

    CERN Document Server

    Stoykov, A; Sedlak, K; Rodriguez, J; Greuter, U; Amato, A

    2012-01-01

    Solutions to the detector system of the High-Field muSR instrument at the Paul Scherrer Institut (PSI) in Switzerland are presented. The strict technical requirements are fulfilled through the application of Geiger-mode Avalanche Photodiodes.

  18. [Avalanche emergencies. Review of the current situation].

    Science.gov (United States)

    Paal, P; Beikircher, W; Brugger, H

    2006-03-01

    In North America and Europe around 140 persons die every year due to avalanches, approximately 35 in North America, 100 in the European Alps, and 5 in other parts of Europe. Most of the victims are skiers and snowboarders. This article outlines the specific pathophysiology of avalanche burials, such as hypoxia, hypercapnia, and hypothermia and also other factors which influence survival. Strategies to minimize the mortality due to avalanches and the on-site treatment of buried persons are discussed. Finally, possibilities to reduce the number of avalanche deaths are pointed out.

  19. Silicon avalanche photodiodes on the base of metal-resistor-semiconductor (MRS) structures

    CERN Document Server

    Saveliev, V

    2000-01-01

    The development of a high quantum efficiency, fast photodetector, with internal gain amplification for the wavelength range 450-600 nm is one of the critical issues for experimental physics - registration of low-intensity light photons flux. The new structure of Silicon Avalanche Detectors with high internal amplification (10 sup 5 -10 sup 6) has been designed, manufactured and tested for registration of visible light photons and charge particles. The main features of Metal-Resistor-Semiconductor (MRS) structures are the high charge multiplication in nonuniform electric field near the 'needle' pn-junction and negative feedback for stabilization of avalanche process due to resistive layer.

  20. Large-area avalanche photodiodes for the detection of soft x rays.

    Science.gov (United States)

    Gullikson, E M; Gramsch, E; Szawlowski, M

    1995-08-01

    The charge-collection efficiency of beveled-edge-type silicon avalanche photodiodes has been determined for soft x rays in the 50-300-eV range. An efficiency of greater than 80% is measured for energies below the Si L absorption edge. The measured efficiency is well described by a model that accounts for absorption in an oxide overlayer and recombination at the front surface of the diode. The avalanche photodiodes are shown to be significantly more sensitive compared with other detectors for pulsed sources such as a laser-produced plasma source. These results are also very encouraging for soft-xray/ extreme-UV applications involving synchrotron radiation.

  1. Silicon avalanche photodiodes on the base of metal-resistor-semiconductor (MRS) structures

    Energy Technology Data Exchange (ETDEWEB)

    Saveliev, V. E-mail: saveliev@mail.desy.de; Golovin, V

    2000-03-11

    The development of a high quantum efficiency, fast photodetector, with internal gain amplification for the wavelength range 450-600 nm is one of the critical issues for experimental physics - registration of low-intensity light photons flux. The new structure of Silicon Avalanche Detectors with high internal amplification (10{sup 5}-10{sup 6}) has been designed, manufactured and tested for registration of visible light photons and charge particles. The main features of Metal-Resistor-Semiconductor (MRS) structures are the high charge multiplication in nonuniform electric field near the 'needle' pn-junction and negative feedback for stabilization of avalanche process due to resistive layer.

  2. Remote detection of artificially triggered avalanches below a fixed avalanche control installation

    Science.gov (United States)

    van Herwijnen, Alec; Simioni, Stephan; Schweizer, Juerg

    2014-05-01

    Avalanche control by explosives is widely used as a temporary preventive measure to reduce avalanche hazard. The goal is to artificially trigger smaller less destructive avalanches, by detonating charges either above or on the snow surface. Hand charges are most often used, whereby the explosives are deployed by manually hand tossing or lowering onto the snow slope. Given the inherent dangers and limitations of this type of avalanche control, fixed avalanche control installations are increasingly used. These consist of strategically placed remote controlled installations that generate an explosion above the snow pack in an avalanche starting zone. While fixed installations can be used at any time and minimize the risk to avalanche control personnel, visual confirmation is still required to verify if an avalanche released. In order to remotely detect artificially triggered avalanches, we therefore developed a low-cost seismic monitoring system. We deployed the monitoring system in a ski area above the town of Davos , in the eastern Swiss Alps, below a Gazex installation, a remote controlled installation that generates an air blast by detonating a fuel-air explosive above the snow pack. The monitoring system consists of three vertical component geophones inserted in the ground at approximately 14, 27 and 46 meters from the Gazex installation. Our results show that, despite the relatively low precision of the monitoring equipment, both the detonation and the resulting avalanches can clearly be identified in the seismic data. Specifically, detonations are characterized by short, high amplitude broadband signals, while avalanches generate much longer, low frequency signals. Furthermore, information on the size of the artificially triggered avalanches is also obtained as it directly relates to the duration of the generated seismic signal. The overall goal is to assess the effectiveness of the fixed avalanche control installation with regards to yield (i.e. number of

  3. On the temporal organization of neuronal avalanches.

    Science.gov (United States)

    Lombardi, Fabrizio; Herrmann, Hans J; Plenz, Dietmar; De Arcangelis, Lucilla

    2014-01-01

    Spontaneous activity of cortex in vitro and in vivo has been shown to organize as neuronal avalanches. Avalanches are cascades of neuronal activity that exhibit a power law in their size and duration distribution, typical features of balanced systems in a critical state. Recently it has been shown that the distribution of quiet times between consecutive avalanches in rat cortex slice cultures displays a non-monotonic behavior with a power law decay at short time scales. This behavior has been attributed to the slow alternation between up and down-states. Here we further characterize the avalanche process and investigate how the functional behavior of the quiet time distribution depends on the fine structure of avalanche sequences. By systematically removing smaller avalanches from the experimental time series we show that size and quiet times are correlated and highlight that avalanche occurrence exhibits the characteristic periodicity of θ and β/γ oscillations, which jointly emerge in most of the analyzed samples. Furthermore, our analysis indicates that smaller avalanches tend to be associated with faster β/γ oscillations, whereas larger ones are associated with slower θ and 1-2 Hz oscillations. In particular, large avalanches corresponding to θ cycles trigger cascades of smaller ones, which occur at β/γ frequency. This temporal structure follows closely the one of nested θ - β/γ oscillations. Finally we demonstrate that, because of the multiple time scales characterizing avalanche dynamics, the distributions of quiet times between avalanches larger than a certain size do not collapse onto a unique function when rescaled by the average occurrence rate. However, when considered separately in the up-state and in the down-state, these distributions are solely controlled by the respective average rate and two different unique function can be identified.

  4. Triaging multiple victims in an avalanche setting: the Avalanche Survival Optimizing Rescue Triage algorithmic approach.

    Science.gov (United States)

    Bogle, Lee B; Boyd, Jeff J; McLaughlin, Kyle A

    2010-03-01

    As winter backcountry activity increases, so does exposure to avalanche danger. A complicated situation arises when multiple victims are caught in an avalanche and where medical and other rescue demands overwhelm resources in the field. These mass casualty incidents carry a high risk of morbidity and mortality, and there is no recommended approach to patient care specific to this setting other than basic first aid principles. The literature is limited with regard to triaging systems applicable to avalanche incidents. In conjunction with the development of an electronic avalanche rescue training module by the Canadian Avalanche Association, we have designed the Avalanche Survival Optimizing Rescue Triage algorithm to address the triaging of multiple avalanche victims to optimize survival and disposition decisions.

  5. Silicon Geiger mode avalanche photodiodes

    Institute of Scientific and Technical Information of China (English)

    M. Mazzillo; S. Billotta; G. Bonanno; A. Campisi; L. Cosentino; P. Finocchiaro; F. Musumeci; S.Privitera; S. Tudisco; G. Condorelli; D. Sanfilippo; G. Fallica; E. Sciacca; S. Aurite; S. Lombardo; E. Rlmini; M. Belluso

    2007-01-01

    In this letter we present the results regarding the electrical and optical characterization of Geiger mode silicon avalanche photodiodes (GMAP) fabricated by silicon standard planar technology. Low dark count rates, negligible afterpulsing effects,good timing resolution and high quantum detection efficiency in all the visible range have been measured. The very good electro-optical performances of our photodiodes make them attractive for the fabrication of arrays with a large number of GMAP to be used both in the commercial and the scientific fields, as telecommunications and nuclear medical imaging.

  6. Plasmonic field confinement for separate absorption-multiplication in InGaAs nanopillar avalanche photodiodes

    Science.gov (United States)

    Farrell, Alan C.; Senanayake, Pradeep; Hung, Chung-Hong; El-Howayek, Georges; Rajagopal, Abhejit; Currie, Marc; Hayat, Majeed M.; Huffaker, Diana L.

    2015-12-01

    Avalanche photodiodes (APDs) are essential components in quantum key distribution systems and active imaging systems requiring both ultrafast response time to measure photon time of flight and high gain to detect low photon flux. The internal gain of an APD can improve system signal-to-noise ratio (SNR). Excess noise is typically kept low through the selection of material with intrinsically low excess noise, using separate-absorption-multiplication (SAM) heterostructures, or taking advantage of the dead-space effect using thin multiplication regions. In this work we demonstrate the first measurement of excess noise and gain-bandwidth product in III-V nanopillars exhibiting substantially lower excess noise factors compared to bulk and gain-bandwidth products greater than 200 GHz. The nanopillar optical antenna avalanche detector (NOAAD) architecture is utilized for spatially separating the absorption region from the avalanche region via the NOA resulting in single carrier injection without the use of a traditional SAM heterostructure.

  7. Plasmonic field confinement for separate absorption-multiplication in InGaAs nanopillar avalanche photodiodes.

    Science.gov (United States)

    Farrell, Alan C; Senanayake, Pradeep; Hung, Chung-Hong; El-Howayek, Georges; Rajagopal, Abhejit; Currie, Marc; Hayat, Majeed M; Huffaker, Diana L

    2015-12-02

    Avalanche photodiodes (APDs) are essential components in quantum key distribution systems and active imaging systems requiring both ultrafast response time to measure photon time of flight and high gain to detect low photon flux. The internal gain of an APD can improve system signal-to-noise ratio (SNR). Excess noise is typically kept low through the selection of material with intrinsically low excess noise, using separate-absorption-multiplication (SAM) heterostructures, or taking advantage of the dead-space effect using thin multiplication regions. In this work we demonstrate the first measurement of excess noise and gain-bandwidth product in III-V nanopillars exhibiting substantially lower excess noise factors compared to bulk and gain-bandwidth products greater than 200 GHz. The nanopillar optical antenna avalanche detector (NOAAD) architecture is utilized for spatially separating the absorption region from the avalanche region via the NOA resulting in single carrier injection without the use of a traditional SAM heterostructure.

  8. Avalanche!--Teachable Moments in Outdoor Education

    Science.gov (United States)

    Galloway, Shayne

    2005-01-01

    Rarely do outdoor educators get the opportunity to safely incorporate an avalanche while the topic of the day is actually avalanche awareness and forecasting. Many similar possibilities exist in the expeditionary context, but even brief excursions may result in incredible learning experiences. These "teachable moments" occur regularly in the…

  9. CHICO, a heavy ion detector for Gammasphere

    CERN Document Server

    Simon, M W; Wu, C Y; Gray, R W; Teng, R; Long, C

    2000-01-01

    A 4 pi position-sensitive heavy-ion detector system, CHICO, has been developed primarily for use in conjunction with the 4 pi gamma-ray facility, Gammasphere. The CHICO detector comprises an array of 20 Parallel Plate Avalanche Counters (PPACs) covering 12 deg.

  10. Observations and modelling of snow avalanche entrainment

    Directory of Open Access Journals (Sweden)

    B. Sovilla

    2002-01-01

    Full Text Available In this paper full scale avalanche dynamics measurements from the Italian Pizzac and Swiss Vallée de la Sionne test sites are used to develop a snowcover entrainment model. A detailed analysis of three avalanche events shows that snowcover entrainment at the avalanche front appears to dominate over bed erosion at the basal sliding surface. Furthermore, the distribution of mass within the avalanche body is primarily a function of basal friction. We show that the mass distribution in the avalanche changes the flow dynamics significantly. Two different dynamical models, the Swiss Voellmy-fluid model and the Norwegian NIS model, are used to back calculate the events. Various entrainment methods are investigated and compared to measurements. We demon-strate that the Norwegian NIS model is clearly better able to simulate the events once snow entrainment has been included in the simulations.

  11. Advanced active quenching circuits for single-photon avalanche photodiodes

    Science.gov (United States)

    Stipčević, M.; Christensen, B. G.; Kwiat, P. G.; Gauthier, D. J.

    2016-05-01

    Commercial photon-counting modules, often based on actively quenched solid-state avalanche photodiode sensors, are used in wide variety of applications. Manufacturers characterize their detectors by specifying a small set of parameters, such as detection efficiency, dead time, dark counts rate, afterpulsing probability and single photon arrival time resolution (jitter), however they usually do not specify the conditions under which these parameters are constant or present a sufficient description. In this work, we present an in-depth analysis of the active quenching process and identify intrinsic limitations and engineering challenges. Based on that, we investigate the range of validity of the typical parameters used by two commercial detectors. We identify an additional set of imperfections that must be specified in order to sufficiently characterize the behavior of single-photon counting detectors in realistic applications. The additional imperfections include rate-dependence of the dead time, jitter, detection delay shift, and "twilighting." Also, the temporal distribution of afterpulsing and various artifacts of the electronics are important. We find that these additional non-ideal behaviors can lead to unexpected effects or strong deterioration of the system's performance. Specifically, we discuss implications of these new findings in a few applications in which single-photon detectors play a major role: the security of a quantum cryptographic protocol, the quality of single-photon-based random number generators and a few other applications. Finally, we describe an example of an optimized avalanche quenching circuit for a high-rate quantum key distribution system based on time-bin entangled photons.

  12. Thermal energy in dry snow avalanches

    Science.gov (United States)

    Steinkogler, W.; Sovilla, B.; Lehning, M.

    2015-09-01

    Avalanches can exhibit many different flow regimes from powder clouds to slush flows. Flow regimes are largely controlled by the properties of the snow released and entrained along the path. Recent investigations showed the temperature of the moving snow to be one of the most important factors controlling the mobility of the flow. The temperature of an avalanche is determined by the temperature of the released and entrained snow but also increases by frictional processes with time. For three artificially released avalanches, we conducted snow profiles along the avalanche track and in the deposition area, which allowed quantifying the temperature of the eroded snow layers. This data set allowed to calculate the thermal balance, from release to deposition, and to discuss the magnitudes of different sources of thermal energy of the avalanches. For the investigated dry avalanches, the thermal energy increase due to friction was mainly depending on the effective elevation drop of the mass of the avalanche with a warming of approximately 0.3 °C per 100 vertical metres. Contrarily, the temperature change due to entrainment varied for the individual avalanches, from -0.08 to 0.3 °C, and depended on the temperature of the snow along the path and the erosion depth. Infrared radiation thermography (IRT) was used to assess the surface temperature before, during and just after the avalanche with high spatial resolution. This data set allowed to identify the warmest temperatures to be located in the deposits of the dense core. Future research directions, especially for the application of IRT, in the field of thermal investigations in avalanche dynamics are discussed.

  13. Thermal energy in dry snow avalanches

    Directory of Open Access Journals (Sweden)

    W. Steinkogler

    2014-11-01

    Full Text Available Avalanches can exhibit many different flow regimes from powder clouds to slush flows. Flow regimes are largely controlled by the properties of the snow released and entrained along the path. Recent investigations showed the temperature of the moving snow to be one of the most important factors controlling the mobility of the flow. The temperature of an avalanche is determined by the temperature of the released and entrained snow but also increases by frictional and collisional processes with time. For three artificially released avalanches, we conducted snow profiles along the avalanche track and in the deposition area, which allowed quantifying the temperature of the eroded snow layers. Infrared radiation thermography (IRT was used to assess the surface temperature before, during and just after the avalanche with high spatial resolution. This data set allowed to calculate the thermal balance, from release to deposition, and to discuss the magnitudes of different sources of thermal energy of the avalanches. We could confirm that, for the investigated dry avalanches, the thermal energy increase due to friction was mainly depending on the elevation drop of the avalanche with a warming of approximately 0.5 °C per 100 height meters. Contrary, warming due to entrainment was very specific to the individual avalanche and depended on the temperature of the snow along the path and the erosion depth ranging from nearly no warming to a maximum observed warming of 1 °C. Furthermore, we could observe the warmest temperatures are located in the deposits of the dense core. Future research directions, especially for the application of IRT, in the field of thermal investigations in avalanche dynamics are discussed.

  14. A Geiger-mode avalanche photodiode array for X-ray photon correlation spectroscopy.

    Science.gov (United States)

    Johnson, I; Sadygov, Z; Bunk, O; Menzel, A; Pfeiffer, F; Renker, D

    2009-01-01

    X-ray photon correlation spectroscopy (XPCS) provides an opportunity to study the dynamics of systems by measuring the temporal fluctuations in a far-field diffraction pattern. A two-dimensional detector system has been developed to investigate fluctuations in the frequency range of several Hz to kHz. The X-ray detector system consists of a thin 100 microm scintillation crystal coupled to a Geiger-mode avalanche photodiode array. In this article the elements of the system are detailed and the detector for XPCS measurements is demonstrated.

  15. Status of Beam Line Detectors for the BigRIPS Fragment Separator at RIKEN RI Beam Factory: Issues on High Rates and Resolution

    Science.gov (United States)

    Sato, Yuki; Fukuda, Naoki; Takeda, Hiroyuki; Kameda, Daisuke; Suzuki, Hiroshi; Shimizu, Yohei; Ahn, DeukSoon; Murai, Daichi; Inabe, Naohito; Shimaoka, Takehiro; Tsubota, Masakatsu; Kaneko, Junichi H.; Chayahara, Akiyoshi; Umezawa, Hitoshi; Shikata, Shinichi; Kumagai, Hidekazu; Murakami, Hiroyuki; Sato, Hiromi; Yoshida, Koichi; Kubo, Toshiyuki

    A multiple sampling ionization chamber (MUSIC) and parallel-plate avalanche counters (PPACs) were installed within the superconducting in-flight separator, named BigRIPS, at the RIKEN Nishina Center for particle identification of RI beams. The MUSIC detector showed negligible charge collection inefficiency from recombination of electrons and ions, up to a 99-kcps incidence rate for high-energy heavy ions. For the PPAC detectors, the electrical discharge durability for incident heavy ions was improved by changing the electrode material. Finally, we designed a single crystal diamond detector, which is under development for TOF measurements of high-energy heavy ions, that has a very fast response time (pulse width <1 ns).

  16. Response of Multi-strip Multi-gap Resistive Plate Chamber

    CERN Document Server

    Datta, Ushasi; Rahaman, A; Basu, P; Basu, J; Bemmerer, D; Boretzky, K; Elekes, Z; Kempe, M; Munzenberg, G; Simon, H; Sobiella, M; Stach, D; Wagner, A; Yakorev, D

    2015-01-01

    A prototype of Multi-strip Multi-gap Resistive Plate chamber (MMRPC) with active area 40 cm $\\times$ 20 cm has been developed at SINP, Kolkata. Detailed response of the developed detector was studied with the pulsed electron beam from ELBE at Helmholtz-Zentrum Dresden-Rossendorf. In this report the response of SINP developed MMRPC with different controlling parameters is described in details. The obtained time resolution ($\\sigma_t$) of the detector after slew correction was 91.5$ \\pm $3 ps. Position resolution measured along ($\\sigma_x$) and across ($\\sigma_y$) the strip was 2.8$\\pm$0.6 cm and 0.58 cm, respectively. The measured absolute efficiency of the detector for minimum ionizing particle like electron was 95.8$\\pm$1.3 $\\%$. Better timing resolution of the detector can be achieved by restricting the events to a single strip. The response of the detector was mainly in avalanche mode but a few percentage of streamer mode response was also observed. A comparison of the response of these two modes with trig...

  17. Equilibrium avalanches in spin glasses

    Science.gov (United States)

    Le Doussal, Pierre; Müller, Markus; Wiese, Kay Jörg

    2012-06-01

    We study the distribution of equilibrium avalanches (shocks) in Ising spin glasses which occur at zero temperature upon small changes in the magnetic field. For the infinite-range Sherrington-Kirkpatrick (SK) model, we present a detailed derivation of the density ρ(ΔM) of the magnetization jumps ΔM. It is obtained by introducing a multicomponent generalization of the Parisi-Duplantier equation, which allows us to compute all cumulants of the magnetization. We find that ρ(ΔM)˜ΔM-τ with an avalanche exponent τ=1 for the SK model, originating from the marginal stability (criticality) of the model. It holds for jumps of size 1≪ΔMmodel. For finite-range models, using droplet arguments, we obtain the prediction τ=(df+θ)/dm where df,dm, and θ are the fractal dimension, magnetization exponent, and energy exponent of a droplet, respectively. This formula is expected to apply to other glassy disordered systems, such as the random-field model and pinned interfaces. We make suggestions for further numerical investigations, as well as experimental studies of the Barkhausen noise in spin glasses.

  18. The solid state detector technology for picosecond laser ranging

    Science.gov (United States)

    Prochazka, Ivan

    1993-01-01

    We developed an all solid state laser ranging detector technology, which makes the goal of millimeter accuracy achievable. Our design and construction philosophy is to combine the techniques of single photon ranging, ultrashort laser pulses, and fast fixed threshold discrimination while avoiding any analog signal processing within the laser ranging chain. The all solid state laser ranging detector package consists of the START detector and the STOP solid state photon counting module. Both the detectors are working in an optically triggered avalanche switching regime. The optical signal is triggering an avalanche current buildup which results in the generation of a uniform, fast risetime output pulse.

  19. Arrest of Avalanche Propagation by Discontinuities on Snow Cover

    Science.gov (United States)

    Frigo, B.; Chiaia, B.

    2009-04-01

    Considering the spatial variability of the snow cover, the paper analyses, in the framework of Fracture Mechanics, the Mode II fracture propagation on snow cover that leads to large dry slab avalanches. Under the hypothesis of a perfectly brittle phenomenon, avalanche triggering is usually investigated numerically by means of Linear Elastic Fracture Mechanics (McClung, 1979; Chiaia et al., 2008). Since, however, the real phenomenon is intrinsically dynamical, another aspect to investigate is represented by dynamic fracture propagation. In this paper, we model dynamic crack propagation into a dry snow slab, to assess the possibility of crack arrest due to the presence of weak zones distributed along the snow slope. As a consequence of the first triggering mechanism (the Mode II fracture propagation on the weak plane), the secondary Mode I crack propagation in the crown is studied by means of numerical simulations based on Dynamic Elastic Fracture Mechanics and on the theory of crack arresters. By taking into account kinetic energy and using the FEM software FRANC 2D (Wawrzynek and Ingraffea, 1993), several paths of crown fracture propagation and their stability have been investigated. The snowpack is considered as a linear-elastic plate (2D problem), whose physical and mechanical parameters are chosen according to classical literature values. To investigate the possible arrest of crown fracture, we apply the theory of crack arresters, usually adopted for pipelines and perforated steel sheets fracture problems. To study crack arrest, different crack paths are simulated, in discontinuous (equipped with different shapes and geometries of artificial voids) snowpacks. The simulations show the effectiveness of these weak zones, to reduce substantially the crack driving force of the propagating fracture. This means that, increasing spatial variability tends to stabilize the snow slope, eventually splitting a major avalanche event into smaller, independent avalanches. Our

  20. Hummock alignment in Japanese volcanic debris avalanches controlled by pre-avalanche slope of depositional area

    Science.gov (United States)

    Yoshida, Hidetsugu

    2014-10-01

    This paper investigates the relationship of hummock orientation to the flow dynamics of volcanic debris avalanches. There are opposing views on whether hummocks are systematically aligned along debris avalanche paths, or not. To investigate this geomorphologically fundamental question, I investigated hummock orientation for six Japanese debris avalanches of two simple styles: four "freely spreading" debris avalanches, and two "valley-filling" debris avalanches. Quantitative GIS-based data analysis revealed that hummock orientation along the avalanche flow path alternated between dominantly parallel to and dominantly perpendicular to the flow direction. These changes of alignment reflect dynamic changes of the local stress field within the avalanche, alternating between extensional and compressional in response to changes of the slope of the pre-avalanche ground surface. Changes of hummock alignment from perpendicular to parallel indicate that the local stress regime has changed from compressional to extensional. Conversely, changes of hummock alignment from parallel to perpendicular indicate that the local stress regime has changed from extensional to compressional. Thus, this research demonstrated a clear relationship between hummock orientation and dynamic changes of stress regime within avalanches that are related to changes of the slope of the pre-avalanche ground surface.

  1. Gas gain characteristics of parallel plate avalanche counter

    Energy Technology Data Exchange (ETDEWEB)

    Nishio, Katsuhisa; Yamamoto, Hideki; Kanno, Ikuo; Kimura, Itsuro [Kyoto Univ. (Japan). Faculty of Engineering; Nakagome, Y.

    1996-07-01

    In the conventional gas gain theory, the Townsend primary ionization coefficient is expressed as a function of S, which is the ratio of the electric field strength (E) to the gas density (N). In this paper, an experimental form of {alpha} is derived from the data and is compared with the formula so far. (J.P.N.)

  2. Single-Photon Avalanche Diodes (SPAD) in CMOS 0.35 μm technology

    Science.gov (United States)

    Pellion, D.; Jradi, K.; Brochard, N.; Prêle, D.; Ginhac, D.

    2015-07-01

    Some decades ago single photon detection used to be the terrain of photomultiplier tube (PMT), thanks to its characteristics of sensitivity and speed. However, PMT has several disadvantages such as low quantum efficiency, overall dimensions, and cost, making them unsuitable for compact design of integrated systems. So, the past decade has seen a dramatic increase in interest in new integrated single-photon detectors called Single-Photon Avalanche Diodes (SPAD) or Geiger-mode APD. SPAD are working in avalanche mode above the breakdown level. When an incident photon is captured, a very fast avalanche is triggered, generating an easily detectable current pulse. This paper discusses SPAD detectors fabricated in a standard CMOS technology featuring both single-photon sensitivity, and excellent timing resolution, while guaranteeing a high integration. In this work, we investigate the design of SPAD detectors using the AMS 0.35 μm CMOS Opto technology. Indeed, such standard CMOS technology allows producing large surface (few mm2) of single photon sensitive detectors. Moreover, SPAD in CMOS technologies could be associated to electronic readout such as active quenching, digital to analog converter, memories and any specific processing required to build efficient calorimeters1

  3. Temporal correlations in neuronal avalanche occurrence

    Science.gov (United States)

    Lombardi, F.; Herrmann, H. J.; Plenz, D.; de Arcangelis, L.

    2016-04-01

    Ongoing cortical activity consists of sequences of synchronized bursts, named neuronal avalanches, whose size and duration are power law distributed. These features have been observed in a variety of systems and conditions, at all spatial scales, supporting scale invariance, universality and therefore criticality. However, the mechanisms leading to burst triggering, as well as the relationship between bursts and quiescence, are still unclear. The analysis of temporal correlations constitutes a major step towards a deeper understanding of burst dynamics. Here, we investigate the relation between avalanche sizes and quiet times, as well as between sizes of consecutive avalanches recorded in cortex slice cultures. We show that quiet times depend on the size of preceding avalanches and, at the same time, influence the size of the following one. Moreover we evidence that sizes of consecutive avalanches are correlated. In particular, we show that an avalanche tends to be larger or smaller than the following one for short or long time separation, respectively. Our analysis represents the first attempt to provide a quantitative estimate of correlations between activity and quiescence in the framework of neuronal avalanches and will help to enlighten the mechanisms underlying spontaneous activity.

  4. Temporal correlations in neuronal avalanche occurrence.

    Science.gov (United States)

    Lombardi, F; Herrmann, H J; Plenz, D; de Arcangelis, L

    2016-04-20

    Ongoing cortical activity consists of sequences of synchronized bursts, named neuronal avalanches, whose size and duration are power law distributed. These features have been observed in a variety of systems and conditions, at all spatial scales, supporting scale invariance, universality and therefore criticality. However, the mechanisms leading to burst triggering, as well as the relationship between bursts and quiescence, are still unclear. The analysis of temporal correlations constitutes a major step towards a deeper understanding of burst dynamics. Here, we investigate the relation between avalanche sizes and quiet times, as well as between sizes of consecutive avalanches recorded in cortex slice cultures. We show that quiet times depend on the size of preceding avalanches and, at the same time, influence the size of the following one. Moreover we evidence that sizes of consecutive avalanches are correlated. In particular, we show that an avalanche tends to be larger or smaller than the following one for short or long time separation, respectively. Our analysis represents the first attempt to provide a quantitative estimate of correlations between activity and quiescence in the framework of neuronal avalanches and will help to enlighten the mechanisms underlying spontaneous activity.

  5. Avalanche Initiaition Mechanism - A Finite-element Approach

    Directory of Open Access Journals (Sweden)

    S. Senthil

    2003-01-01

    Full Text Available The Himalayas, the longest chain of mountains in the world, experiences extensive snowfall and avalanche activity during winter. Some of these areas are densely populated, and death and destruction on large scale due to avalanche activity has been reported in these areas. One of the ways of reducing the loss of life and material due to avalanches is through prediction of avalanches. An understanding of weather forecasting, terrain, and avalanche initiation mechanism is a prerequisite for avalanche prediction. In the present paper mathematical modelling of avalanche initiation mechanism has been discussed.

  6. Design and realization of a facility for the characterization of Silicon Avalanche PhotoDiodes

    CERN Document Server

    Celentano, Andrea; De Vita, Raffaella; Fegan, Stuart; Mini, Giuseppe; Nobili, Gianni; Ottonello, Giacomo; Parodi, Franco; Rizzo, Alessandro; Zonta, Irene

    2015-01-01

    We present the design, construction, and performance of a facility for the characterization of Silicon Avalanche Photodiodes in the operating temperature range between -2 $^\\circ$C and 25 $^\\circ$C. The system can simultaneously measure up to 24 photo-detectors, in a completely automatic way, within one day of operations. The measured data for each sensor are: the internal gain as a function of the bias voltage and temperature, the gain variation with respect to the bias voltage, and the dark current as a function of the gain. The systematic uncertainties have been evaluated during the commissioning of the system to be of the order of 1%. This paper describes in detail the facility design and layout, and the procedure employed to characterize the sensors. The results obtained from the measurement of the 380 Avalanche Photodiodes of the CLAS12-Forward Tagger calorimeter detector are then reported, as the first example of the massive usage of the facility.

  7. Performance of InGaAs/InP Avalanche Photodiodes as Gated-Mode Photon Counters.

    Science.gov (United States)

    Ribordy, G; Gautier, J D; Zbinden, H; Gisin, N

    1998-04-20

    We investigate the performance of separate absorption multiplication InGaAs/InP avalanche photodiodes as single-photon detectors for 1.3- and 1.55-mum wavelengths. First we study afterpulses and choose experimental conditions to limit this effect. Then we compare the InGaAs/InP detector with a germanium avalanche photodiode; the former shows a lower dark-count rate. The effect of operating temperature is studied for both wavelengths. At 173 K and with a dark-count probability per gate of 10(-4), detection efficiencies of 16% for 1.3 mum and 7% for 1.55 mum are obtained. Finally, a timing resolution of less than200 ps is demonstrated.

  8. Single photon detector design features

    Science.gov (United States)

    Zaitsev, Sergey V.; Kurochkin, Vladimir L.; Kurochkin, Yury V.

    2016-12-01

    In the report are discussed the laboratory test results of SPAD detectors with InGaAs / InP avalanche photodiodes, operating in Geiger mode. Device operating in synchronous mode with the dead timer setting for proper working conditions of photodiodes. The report materials will showing the functional block diagram of the detector, real operating signals in the receiver path and clock circuits and main results of measurements. The input signal of the synchronous detector is the clock, which determines the time positions of expected photons arrival. Increasing the clock speed 1-300 MHz or getting more time positions of the time grid, we provide increased capacity for time position code of signals, when QKD information transmitted over the nets. At the same time, the maximum attainable speed of photon reception is limited by diode dead time. Diode quantum noise are minimized by inclusion of a special time interval - dead time 0.1-10 usec, after each received and registered a photon. The lowest attainable value of the dead time is determined as a compromise between transients in electrical circuits, passive avalanche «quenching» circuit and thermal transients cooling crystal diode, after each avalanche pass though photodiode. Achievable time and speed parameters are discussed with specific examples of detectors.

  9. A space- and time-resolved single photon counting detector for fluorescence microscopy and spectroscopy

    Science.gov (United States)

    Michalet, X.; Siegmund, O. H. W.; Vallerga, J. V.; Jelinsky, P.; Millaud, J. E.; Weiss, S.

    2006-02-01

    We have recently developed a wide-field photon-counting detector having high-temporal and high-spatial resolutions and capable of high-throughput (the H33D detector). Its design is based on a 25 mm diameter multi-alkali photocathode producing one photo electron per detected photon, which are then multiplied up to 10 7 times by a 3-microchannel plate stack. The resulting electron cloud is proximity focused on a cross delay line anode, which allows determining the incident photon position with high accuracy. The imaging and fluorescence lifetime measurement performances of the H33D detector installed on a standard epifluorescence microscope will be presented. We compare them to those of standard single-molecule detectors such as single-photon avalanche photodiode (SPAD) or electron-multiplying camera using model samples (fluorescent beads, quantum dots and live cells). Finally, we discuss the design and applications of future generation of H33D detectors for single-molecule imaging and high-throughput study of biomolecular interactions.

  10. Strategies for reducing the environmental impact of gaseous detector operation at the CERN LHC experiments

    Science.gov (United States)

    Capeans, M.; Guida, R.; Mandelli, B.

    2017-02-01

    A wide range of gas mixtures is used for the operation of different gaseous detectors at the Large Hadron Collider (LHC) experiments. Nowadays some of these gases, as C2H2F4, CF4 and SF6, are indicated as greenhouse gases (GHG) and dominate the overall GHG emission from particle detectors at the LHC experiments. The release of GHG is an important subject for the design of future particle detectors as well as for the operation of the current experiments. Different strategies have been adopted at CERN for reducing the GHG emissions. The standard approach is the recirculation of the gas mixture with complex gas systems where system stability and the possible accumulation of impurities need to be attentively evaluated for the good operation and safety of the detectors. A second approach is based on the recuperation of the gas mixture exiting the detectors and the separation of its gas components for re-use. At long-term, the use of less invasive gases is being investigated, especially for the Resistive Plate Chamber (RPC) systems. Operation of RPC with environmentally friendly gas mixtures is demonstrated for streamer mode while avalanche mode operation needs more complex gas mixtures.

  11. Monitoring and modelling snow avalanches in Svalbard

    Science.gov (United States)

    Humlum, O.; Christiansen, H.; Neumann, U.; Eckerstorfer, M.; Sjöblom, A.; Stalsberg, K.; Rubensdotter, L.

    2009-04-01

    Monitoring and modelling snow avalanches in Svalbard Ole Humlum 1,3, Hanne H. Christiansen 1, Ulrich Neumann 1, Markus Eckerstorfer 1, Anna Sjöblom 1, Knut Stalsberg 2 and Lena Rubensdotter 2. 1: The University Centre in Svalbard (UNIS). 2: Geological Survey of Norway (NGU) 3: University of Oslo Ground based transportation in Svalbard landscape all takes place across mountainous terrain affected by different geomorphological slope processes. Traffic in and around the Svalbard settlements is increasing, and at the same time global climate models project substantial increases in temperature and precipitation in northern high latitudes for coming century. Therefore improved knowledge on the effect of climatic changes on slope processes in such high arctic landscapes is becoming increasingly important. Motivated by this, the CRYOSLOPE Svalbard research project since 2007 has carried out field observations on snow avalanche frequency and associated meteorological conditions. Snow avalanches are important geomorphic agents of erosion and deposition, and have long been a source of natural disasters in many mid-latitude mountain areas. Avalanches as a natural hazard has thereby been familiar to inhabitants of the Alps and Scandinavia for centuries, while it is a more recent experience in high arctic Svalbard. In addition, overall climate, topography and especially high winter wind speeds makes it difficult to apply snow avalanche models (numerical or empirical) developed for use at lower latitudes, e.g. in central Europe. In the presentation we examplify results from the ongoing (since winter 2006-07) monitoring of snow avalanches in Svalbard along a 70 km long observational route in the mountains. In addition, we present observations on the geomorphological impact of avalanches, with special reference to the formation of rock glaciers. Finally, we also present some initial results from numerical attempts of snow avalanche risk modelling within the study area.

  12. Statistics of Electron Avalanches and Streamers

    Directory of Open Access Journals (Sweden)

    T. Ficker

    2007-01-01

    Full Text Available We have studied the severe systematic deviations of populations of electron avalanches from the Furry distribution, which has been held to be the statistical law corresponding to them, and a possible explanation has been sought. A  new theoretical concept based on fractal avalanche multiplication has been proposed and is shown to be a convenient candidate for explaining these deviations from Furry statistics. 

  13. Catastrophic avalanches and methods of their control

    Directory of Open Access Journals (Sweden)

    N. A. Volodicheva

    2014-01-01

    Full Text Available Definition of such phenomenon as “catastrophic avalanche” is presented in this arti-cle. Several situations with releases of catastrophic avalanches in mountains of Caucasus, Alps, and Central Asia are investigated. Materials of snow-avalanche ob-servations performed since 1960s at the Elbrus station of the Lomonosov Moscow State University (Central Caucasus were used for this work. Complex-valued measures of engineering protection demonstrating different efficiencies are consid-ered.

  14. Effect of water vapor on the performance of glass RPCs in avalanche mode operation

    CERN Document Server

    Raveendrababu, K; Satyanarayana, B; Mukhopadhayay, S; Majumdar, N

    2016-01-01

    We studied the effect of water vapor on the performance of glass Resistive Plate Chambers (RPCs) in the avalanche mode operation. Controlled and calibrated amount of water vapor was added to the RPC gas mixture that has C$_2$H$_2$F$_4$ as the major component. The deterioration in the performance of RPC was observed while operating with wet gas and recovered after switching to standard gas.

  15. Amorphous selenium flat panel detectors for medical applications

    Science.gov (United States)

    Zhao, Wei; Hunt, D. C.; Tanioka, Kenkichi; Rowlands, J. A.

    2005-09-01

    Different technologies for making X-ray sensitive active matrix flat-panel imagers (AMFPI) are reviewed for applications in digital radiography and fluoroscopy. Aspects of imaging performance requiring improvement are identified and potential new detector concepts addressing these issues are briefly described. The rationale is given for the investigation of a new detector concept—an indirect conversion FPI with avalanche gain—for low-dose X-ray imaging. This detector consists of an amorphous selenium (a-Se) photoconductor optically coupled to a structured cesium iodide (CsI) scintillator. Under an electric field ESe, the a-Se is sensitive to light and converts the optical photons emitted from CsI into electronic signal that can be stored and read out in the same fashion as in existing AMFPI. When ESe is increased to >90 V/μm, avalanche multiplication occurs. The avalanche gain ranges between 1-800 depending on ESe and the thickness of the a-Se layer. The avalanche a-Se photoconductor is referred to as High-gain Avalanche Rushing amorphous Photoconductor. The feasibility of two detector configurations based on avalanche gain, each using a different image readout method, are under investigation. Their advantages are compared to other AMPFI technologies for digital radiography and fluoroscopy.

  16. Gated Geiger mode avalanche photodiode pixels with integrated readout electronics for low noise photon detection

    OpenAIRE

    Vilella Figueras, Eva; Comerma Montells, Albert; Alonso Casanovas, Oscar; Gascón Fora, David; Diéguez Barrientos, Àngel

    2011-01-01

    Avalanche photodiodes operated in the Geiger mode offer a high intrinsic gain as well as an excellent timing accuracy. These qualities make the sensor specially suitable for those applications where detectors with high sensitivity and low timing uncertainty are required. Moreover, they are compatible with standard CMOS technologies, allowing sensor and front-end electronics integration within the pixel cell. However, the sensor suffers from high levels of intrinsic noise, which may lead to er...

  17. Low dark count geiger mode avalanche photodiodes fabricated in conventional CMOS technologies

    OpenAIRE

    Vilella Figueras, Eva; Arbat Casas, Anna; Alonso Casanovas, Oscar; Comerma Montells, Albert; Trenado, J.; Vilà i Arbonès, Anna Maria; Casanova Mohr, Raimon; Garrido Beltrán, Lluís; Diéguez Barrientos, Àngel

    2011-01-01

    Avalanche photodiodes operated in the Geiger mode present very high intrinsic gain and fast time response, which make the sensor an ideal option for those applications in which detectors with high sensitivity and velocity are required. Moreover, they are compatible with conventional CMOS technologies, allowing sensor and front-end electronics integration within the pixel cell. Despite these excellent qualities, the photodiode suffers from high intrinsic noise, which degrades the performance o...

  18. Relativistic electron avalanches as a thunderstorm discharge competing with lightning.

    Science.gov (United States)

    Kelley, Nicole A; Smith, David M; Dwyer, Joseph R; Splitt, Michael; Lazarus, Steven; Martinez-McKinney, Forest; Hazelton, Bryna; Grefenstette, Brian; Lowell, Alexander; Rassoul, Hamid K

    2015-08-12

    Gamma-ray 'glows' are long duration (seconds to tens of minutes) X-ray and gamma-ray emission coming from thunderclouds. Measurements suggest the presence of relativistic runaway electron avalanches (RREA), the same process underlying terrestrial gamma-ray flashes. Here we demonstrate that glows are relatively a common phenomena near the tops of thunderstorms, when compared with events such as terrestrial gamma-ray flashes. Examining the strongest glow measured by the airborne detector for energetic emissions, we show that this glow is measured near the end of a downward RREA, consistent with occurring between the upper positive charge layer and the negative screening layer above it. The glow discharges the upper positive layer by ≥9.6 mA, strong enough to be an important charging mechanism of the storm. For this glow, the gamma-ray flux observed is close to the value at which relativistic feedback processes become important, with an avalanche multiplication factor of 4,500.

  19. Evolution of the average avalanche shape with the universality class.

    Science.gov (United States)

    Laurson, Lasse; Illa, Xavier; Santucci, Stéphane; Tore Tallakstad, Ken; Måløy, Knut Jørgen; Alava, Mikko J

    2013-01-01

    A multitude of systems ranging from the Barkhausen effect in ferromagnetic materials to plastic deformation and earthquakes respond to slow external driving by exhibiting intermittent, scale-free avalanche dynamics or crackling noise. The avalanches are power-law distributed in size, and have a typical average shape: these are the two most important signatures of avalanching systems. Here we show how the average avalanche shape evolves with the universality class of the avalanche dynamics by employing a combination of scaling theory, extensive numerical simulations and data from crack propagation experiments. It follows a simple scaling form parameterized by two numbers, the scaling exponent relating the average avalanche size to its duration and a parameter characterizing the temporal asymmetry of the avalanches. The latter reflects a broken time-reversal symmetry in the avalanche dynamics, emerging from the local nature of the interaction kernel mediating the avalanche dynamics.

  20. Epitaxial silicon semiconductor detectors, past developments, future prospects

    Energy Technology Data Exchange (ETDEWEB)

    Gruhn, C.R.

    1976-01-01

    A review of the main physical characteristics of epitaxial silicon as it relates to detector development is presented. As examples of applications results are presented on (1) epitaxial silicon avalanche diodes (ESAD); signal-to-noise, non-linear aspects of the avalanche gain mechanism, gain-bandwidth product, (2) ultrathin epitaxial silicon surface barrier (ESSB) detectors, response to heavy ions, (3) an all-epitaxial silicon diode (ESD), response to heavy ions, charge transport and charge defect. Future prospects of epitaxial silicon as it relates to new detector designs are summarized.

  1. Epitaxial silicon semiconductor detectors: past developments, future prospects

    Energy Technology Data Exchange (ETDEWEB)

    Gruhn, C.R.

    1977-02-01

    A review of the main physical characteristics of epitaxial silicon as it relates to detector development is presented. As examples of applications results are presented on (1) epitaxial silicon avalanche diodes (ESAD); signal-to-noise, non-linear aspects of the avalanche gain mechanism, gain-bandwidth product, (2) ultrathin epitaxial silicon surface barrier (ESSB) detectors, response to heavy ions, (3) an all-epitaxial silicon diode (ESD), response to heavy ions, charge transport and charge defect. Future prospects of epitaxial silicon as it relates to new detector designs are summarized.

  2. Design of a new vacuum Compton gamma-ray detector with clad metal electron-converter plate%复合金属发射极真空康普顿探测器结构设计

    Institute of Scientific and Technical Information of China (English)

    韩和同; 王群书; 夏良斌; 管兴胤; 谭新建; 张子川

    2009-01-01

    采用Ta-Al复合金属电子转换靶设计了一种厚窗真空型康普顿探测器,其对1.25 MeVγ射线的探测效率达到7.85×10~(-3)e/γ,比Fe发射极探测器的探测效率高出约2.5倍.探测器具有良好的封装加工和静态真空保持特性,可用于强流脉冲γ射线测量场合.%A newly designed vacuum Compton gamma-ray detector with Ta - Al clad-metal electron converter plate is described. The detecting efficiency for 1.25 MeV gamma-ray is 7. 85 × 10~(-3)e/γ, which is 2.5 times higher than that with Fe converter plate. The designed detector has the merits of well processed and static vacuum keeping and can be used for intense pulsed gamma ray detecting.

  3. PET detector modules based on novel detector technologies

    Energy Technology Data Exchange (ETDEWEB)

    Moses, W.W.; Derenzo, S.E.; Budinger, T.F.

    1994-05-01

    A successful PET detector module must identify 511 keV photons with: high efficiency (>85%), high spatial resolution (<5 mm fwhm), low cost (<$600 / in{sup 2}), low dead time (<4 {mu}s in{sup 2}), good timing resolution (<5 ns fwhm for conventional PET, <200 ps fwhm for time of flight), and good energy resolution (<100 keV fwhm), where these requirements are listed in decreasing order of importance. The ``high efficiency`` requirement also implies that the detector modules must pack together without inactive gaps. Several novel and emerging radiation detector technologies could improve the performance of PET detectors. Avalanche photodiodes, PIN photodiodes, metal channel dynode photomultiplier tubes, and new scintillators all have the potential to improve PET detectors significantly.

  4. Temperature Control of Avalanche Photodiode Using Thermoelectric Cooler

    Science.gov (United States)

    Refaat, Tamer F.; Luck, William S., Jr.; DeYoung, Russell J.

    1999-01-01

    Avalanche photodiodes (APDS) are quantum optical detectors that are used for visible and near infrared optical detection applications. Although APDs are compact, rugged, and have an internal gain mechanism that is suitable for low light intensity; their responsivity, and therefore their output, is strongly dependent on the device temperature. Thermoelectric coolers (TEC) offers a suitable solution to this problem. A TEC is a solid state cooling device, which can be controlled by changing its current. TECs are compact and rugged, and they can precisely control the temperature to within 0.1 C with more than a 150 C temperature gradient between its surfaces. In this Memorandum, a proportional integral (PI) temperature controller for APDs using a TEC is discussed. The controller is compact and can successfully cool the APD to almost 0 C in an ambient temperature environment of up to 27 C.

  5. Improved X-ray detection and particle identification with avalanche photodiodes

    CERN Document Server

    Diepold, Marc; Machado, Jorge; Amaro, Pedro; Abdou-Ahmed, Marwan; Amaro, Fernando D; Antognini, Aldo; Biraben, François; Chen, Tzu-Ling; Covita, Daniel S; Dax, Andreas J; Franke, Beatrice; Galtier, Sandrine; Gouvea, Andrea L; Götzfried, Johannes; Graf, Thomas; Hänsch, Theodor W; Hildebrandt, Malte; Indelicato, Paul; Julien, Lucile; Kirch, Klaus; Knecht, Andreas; Kottmann, Franz; Krauth, Julian J; Liu, Yi-Wei; Monteiro, Cristina M B; Mulhauser, Françoise; Naar, Boris; Nebel, Tobias; Nez, François; Santos, José Paulo; Santos, Joaquim M F dos; Schuhmann, Karsten; Szabo, Csilla I; Taqqu, David; Veloso, João F C A; Voss, Andreas; Weichelt, Birgit; Pohl, Randolf

    2015-01-01

    Avalanche photodiodes are commonly used as detectors for low energy x-rays. In this work we report on a fitting technique used to account for different detector responses resulting from photo absorption in the various APD layers. The use of this technique results in an improvement of the energy resolution at 8.2 keV by up to a factor of 2, and corrects the timing information by up to 25 ns to account for space dependent electron drift time. In addition, this waveform analysis is used for particle identification, e.g. to distinguish between x-rays and MeV electrons in our experiment.

  6. Detection probabilities for photon-counting avalanche photodiodes applied to a laser radar system.

    Science.gov (United States)

    Henriksson, Markus

    2005-08-20

    Arrays of photon-counting avalanche photodiodes with time-resolved readout can improve the performance of three-dimensional laser radars. A comparison of the detection and false-alarm probabilities for detectors in linear mode and in Geiger mode is shown. With low background radiation their performance is comparable. It is shown that in both cases it will be necessary to process several laser shots of the same scene to improve detection and reduce the false-alarm rate. Additional calculations show that the linear mode detector is much better at detecting targets behind semitransparent obscurations such as vegetation and camouflage nets.

  7. Active quenching circuit for single-photon detection with Geiger mode avalanche photodiodes.

    Science.gov (United States)

    Stipcević, Mario

    2009-03-20

    In this paper a novel construction of an active quenching circuit intended for single-photon detection is presented, along with a few original methods for its evaluation. The circuit has been combined with a standard avalanche photodiode C30902S to form a single-photon detector. This detector has a dead time of 39 ns, maximum random counting frequency of 14 MHz, small afterpulsing probability, an estimated peak detection efficiency of over 20%, and a dark count rate of less than 100 Hz. This simple and robust active quenching circuit can be built from off-the-shelf electronic components and is presented with the detailed schematic diagram.

  8. Turn-key Near-Infrared Photon-Counting Detector Module for LIDAR Applications Project

    Data.gov (United States)

    National Aeronautics and Space Administration — We propose to design and deliver a turn-key photon counting detector module for near-infrared wavelengths, based on large-area InGaAs/InP avalanche photodiodes...

  9. Advantages of gated silicon single photon detectors

    Science.gov (United States)

    Legré, Matthieu; Lunghi, Tommaso; Stucki, Damien; Zbinden, Hugo

    2013-05-01

    We present gated silicon single photon detectors based on two commercially available avalanche photodiodes (APDs) and one customised APD from ID Quantique SA. This customised APD is used in a commercially available device called id110. A brief comparison of the two commercial APDs is presented. Then, the charge persistence effect of all of those detectors that occurs just after a strong illumination is shown and discussed.

  10. Rock avalanches: significance and progress (Invited)

    Science.gov (United States)

    Davies, T. R.

    2013-12-01

    1. The probability distribution of landslide volumes follows a power-law indicating that large rock avalanches dominate the terrestrial sediment supply from mountains, and that their source area morphologies dominate mountain topography. 2. Large rock slope failures (~ 106 m3 or greater) often mobilise into rock avalanches, which can travel extraordinarily long distances with devastating effect. This hypermobility has been the subject of many investigations; we have demonstrated that it can be explained quantitatively and accurately by considering the energetics of the intense rock fragmentation that always occurs during motion of a large rock mass. 3. Study of rock avalanche debris psd shows that the energy used in creating new rock surface area during fragmentation is not lost to surface energy, but is recycled generating a high-frequency elastic energy field that reduces the frictional resistance to motion during runout. 4. Rock avalanches that deposit on glaciers can eventually form large terminal moraines that have no connection with any climatic event; unless these are identified as rock-avalanche-influenced they can confuse palaeoclimatic inferences drawn from moraine ages. Rock-avalanche-derived fines, however, can be identified in moraine debris up to ten thousand years old by the characteristic micron-scale agglomerates that form during intense fragmentation, and which are absent from purely climatically-induced moraines; there is thus a strong case for re-examining existing palaeoclimatic databases to eliminate potentially rock-avalanche-influenced moraine ages. 5. Rock avalanches (especially coseismic ones) are a serious hazard, being very destructive in their own right; they also block river valleys, forming landslide dams and potentially devastating dambreak floods, and subsequent severe decade-scale aggradation of downstream fans and floodplains. Rock avalanches falling into lakes or fiords can cause catastrophic tsunami that pose a serious risk to

  11. Advantages of gated silicon single photon detectors

    CERN Document Server

    Lunghi, T; Barreiro, C; Stucki, D; Sanguinetti, B; Zbinden, H

    2012-01-01

    We present a gated silicon single photon detector based on a commercially available avalanche photodiode. Our detector achieves a photon detection efficiency of 45\\pm5% at 808 nm with 2x 10^-6 dark count per ns at -30V of excess bias and -30{\\deg}C. We compare gated and free-running detectors and show that this mode of operation has significant advantages in two representative experimental scenarios: detecting a single photon either hidden in faint continuous light or after a strong pulse. We also explore, at different temperatures and incident light intensities, the "charge persistence" effect, whereby a detector clicks some time after having been illuminated.

  12. Deterministically Driven Avalanche Models of Solar Flares

    Science.gov (United States)

    Strugarek, Antoine; Charbonneau, Paul; Joseph, Richard; Pirot, Dorian

    2014-08-01

    We develop and discuss the properties of a new class of lattice-based avalanche models of solar flares. These models are readily amenable to a relatively unambiguous physical interpretation in terms of slow twisting of a coronal loop. They share similarities with other avalanche models, such as the classical stick-slip self-organized critical model of earthquakes, in that they are driven globally by a fully deterministic energy-loading process. The model design leads to a systematic deficit of small-scale avalanches. In some portions of model space, mid-size and large avalanching behavior is scale-free, being characterized by event size distributions that have the form of power-laws with index values, which, in some parameter regimes, compare favorably to those inferred from solar EUV and X-ray flare data. For models using conservative or near-conservative redistribution rules, a population of large, quasiperiodic avalanches can also appear. Although without direct counterparts in the observational global statistics of flare energy release, this latter behavior may be relevant to recurrent flaring in individual coronal loops. This class of models could provide a basis for the prediction of large solar flares.

  13. Deterministically Driven Avalanche Models of Solar Flares

    CERN Document Server

    Strugarek, Antoine; Joseph, Richard; Pirot, Dorian

    2014-01-01

    We develop and discuss the properties of a new class of lattice-based avalanche models of solar flares. These models are readily amenable to a relatively unambiguous physical interpretation in terms of slow twisting of a coronal loop. They share similarities with other avalanche models, such as the classical stick--slip self-organized critical model of earthquakes, in that they are driven globally by a fully deterministic energy loading process. The model design leads to a systematic deficit of small scale avalanches. In some portions of model space, mid-size and large avalanching behavior is scale-free, being characterized by event size distributions that have the form of power-laws with index values, which, in some parameter regimes, compare favorably to those inferred from solar EUV and X-ray flare data. For models using conservative or near-conservative redistribution rules, a population of large, quasiperiodic avalanches can also appear. Although without direct counterparts in the observational global st...

  14. High Resolution Radar Measurements of Snow Avalanches

    Science.gov (United States)

    McElwaine, Jim; Sovilla, Betty; Vriend, Nathalie; Brennan, Paul; Ash, Matt; Keylock, Chris

    2013-04-01

    Geophysical mass flows, such as snow avalanches, are a major hazard in mountainous areas and have a significant impact on the infrastructure, economy and tourism of such regions. Obtaining a thorough understanding of the dynamics of snow avalanches is crucial for risk assessment and the design of defensive structures. However, because the underlying physics is poorly understood there are significant uncertainties concerning current models, which are poorly validated due to a lack of high resolution data. Direct observations of the denser core of a large avalanche are particularly difficult, since it is frequently obscured by the dilute powder cloud. We have developed and installed a phased array FMCW radar system that penetrates the powder cloud and directly images the dense core with a resolution of around 1 m at 50 Hz over the entire slope. We present data from recent avalanches at Vallee de la Sionne that show a wealth of internal structure and allow the tracking of individual fronts, roll waves and surges down the slope for the first time. We also show good agreement between the radar results and existing measurement systems that record data at particular points on the avalanche track.

  15. Avalanche dynamics in silicon avalanche single- and few-photon sensitive photodiode

    Energy Technology Data Exchange (ETDEWEB)

    Blazej, J; Prochazka, I, E-mail: blazej@fjfi.cvut.c [Czech Technical University in Prague, Brehova 7, 115 19 Prague 1 (Czech Republic)

    2009-11-15

    We are presenting the results of the study of the Single Photon Avalanche Diode (SPAD) avalanche pulse response rise-time and its dependence on several key parameters. We were investigating the unique properties of K14 type SPAD with its high delay uniformity of 200 {mu}m active area, the character of avalanche, and the correlation between the avalanche build-up time and the photon number involved in the avalanche trigger. The detection chip was operated with bias higher then breakdown voltage, ie. in Geiger mode. The detection chip was operated in a passive quenching circuit with active gating. This set-up enabled us to monitor both the diode reverse current using an electrometer and a fast digitizing oscilloscope. The electrometer reading enabled to estimate the photon number per detection event, the avalanche build up was recorded on the oscilloscope and processed by custom designed waveform analysis package. The correlation of avalanche build up to the photon number, bias above break, photon absorption location, optical pulse length and photon energy was investigated in detail. The experimental results are presented.

  16. Assessment of the Perchertal avalanche in Tyrol, Austria

    OpenAIRE

    KURT, Tayfun

    2014-01-01

    The present study has been conducted to analyze the Perchertal avalanche area near Bärenkopf Mountain, which has several avalanche-prone areas on its slopes, within the area of Pertisau, Tyrol, in Austria. The main focus is on identifying the characteristics of the avalanche process itself to determine the potential risk to endangered objects, which include an important road and a hotel. Another focus is to evaluate the current local hazard map. Based on the dynamic avalanche models (Samos-AT...

  17. Relating rock avalanche morphology to emplacement processes

    Science.gov (United States)

    Dufresne, Anja; Prager, Christoph; Bösmeier, Annette

    2015-04-01

    The morphology, structure and sedimentological characteristics of rock avalanche deposits reflect both internal emplacement processes and external influences, such as runout path characteristics. The latter is mainly predisposed by topography, substrate types, and hydrogeological conditions. Additionally, the geological setting at the source slope controls, e.g. the spatial distribution of accumulated lithologies and hence material property-related changes in morphology, or the maximum clast size and amount of fines of different lithological units. The Holocene Tschirgant rock avalanche (Tyrol, Austria) resulted from failure of an intensely deformed carbonate rock mass on the southeast face of a 2,370-m-high mountain ridge. The initially sliding rock mass rapidly fragmented as it moved towards the floor of the Inn River valley. Part of the 200-250 x 106 m3 (Patzelt 2012) rock avalanche debris collided with and moved around an opposing bedrock ridge and flowed into the Ötz valley, reaching up to 6.3 km from source. Where the Tschirgant rock avalanche spread freely it formed longitudinal ridges aligned along motion direction as well as smaller hummocks. Encountering high topography, it left runup ridges, fallback patterns (i.e. secondary collapse), and compressional morphology (successively elevated, transverse ridges). Further evidence for the mechanical landslide behaviour is given by large volumes of mobilized valley-fill sediments (polymict gravels and sands). These sediments indicate both shearing and compressional faulting within the rock avalanche mass (forming their own morphological units through, e.g. in situ bulldozing or as distinctly different hummocky terrain), but also indicate extension of the spreading landslide mass (i.e. intercalated/injected gravels encountered mainly in morphological depressions between hummocks). Further influences on its morphology are given by the different lithological units. E.g. the transition from massive dolomite

  18. Adjoint method and runaway electron avalanche

    Science.gov (United States)

    Liu, Chang; Brennan, Dylan P.; Boozer, Allen H.; Bhattacharjee, Amitava

    2017-02-01

    The adjoint method for the study of runaway electron dynamics in momentum space Liu et al (2016 Phys. Plasmas 23 010702) is rederived using the Green’s function method, for both the runaway probability function (RPF) and the expected loss time (ELT). The RPF and ELT obtained using the adjoint method are presented, both with and without the synchrotron radiation reaction force. The adjoint method is then applied to study the runaway electron avalanche. Both the critical electric field and the growth rate for the avalanche are calculated using this fast and novel approach.

  19. Semiconductor radiation detector with internal gain

    Energy Technology Data Exchange (ETDEWEB)

    Iwanczyk, Jan (Los Angeles, CA); Patt, Bradley E. (Sherman Oaks, CA); Vilkelis, Gintas (Westlake Village, CA)

    2003-04-01

    An avalanche drift photodetector (ADP) incorporates extremely low capacitance of a silicon drift photodetector (SDP) and internal gain that mitigates the surface leakage current noise of an avalanche photodetector (APD). The ADP can be coupled with scintillators such as CsI(Tl), NaI(Tl), LSO or others to form large volume scintillation type gamma ray detectors for gamma ray spectroscopy, photon counting, gamma ray counting, etc. Arrays of the ADPs can be used to replace the photomultiplier tubes (PMTs) used in conjunction with scintillation crystals in conventional gamma cameras for nuclear medical imaging.

  20. First experiments for the detection of simulated mammographic lesions. Digital full field mammography with a new detector with a double plate of pure selenium; Erste Untersuchungen zur Detektion simulierter mammographischer Laesionen. Digitale Vollfeldmammographie mit einem Doppelschicht-Selen-Detektor

    Energy Technology Data Exchange (ETDEWEB)

    Schulz-Wendtland, R.; Wenkel, E.; Adamietz, B.; Lell, M.; Anders, K.; Uder, M. [Universitaetsklinikum Erlangen, Abteilung Gynaekologische Radiologie, Radiologisches Institut, Erlangen (Germany); Hermann, K.P. [Universitaetsmedizin Goettingen, Abteilung Diagnostische Radiologie, Goettingen (Germany)

    2011-02-15

    The article describes an experimental phantom study of a system for digital full field mammography with a new digital detector with a double plate of pure selenium. The experiments were carried out with the new full field digital mammography system Amulet from FujiFilm. This system has a new detector (18 x 24 cm{sup 2}) on the basis of highly purified amorphous selenium (a-Se) with a pixel size of 50 {mu}m. The x-rays are converted into electric signals in the first plate which are read into the second plate with the help of an optical switch and demonstrated in the form of an image. In this way a better pixel size/volume and signal-to-noise ratio should be achieved. The object of the investigation was the Wisconsin Mammographic Random Phantom, Model 152 A (Technical Performance Mo/Mo, 28 kV, 100 mAs). Five investigators with different experiences in mammography each received three images on a monitor with different random positions of the simulated lesions in the phantom for assessment. The detection rates were compared under the same conditions with the results of two other full field digital mammography systems. The median detection rate for all images and investigators for the new doubled plated a-Se detector with optical switch was 98.7%. For both other systems with a-Si or and a-Se detectors the detection rate was 89.8% or 97.3%, respectively. There were no significant differences in the detection rate of the simulated breast lesions for all three systems considering the interobserver and intraobserver variation. The first phantom study for the detection of simulated breast lesions with the new full field digital mammography system Amulet demonstrates equivalent results with the other systems used in the clinical routine. The trend towards superiority of the new system has to be confirmed in further clinical studies. (orig.) [German] Im Rahmen einer Phantomstudie sollte untersucht werden, ob ein neues System zur digitalen Vollfeldmammographie, das mit einem

  1. High temperature and wavelength dependence of avalanche gain of AlAsSb avalanche photodiodes.

    Science.gov (United States)

    Sandall, Ian C; Xie, Shiyu; Xie, Jingjing; Tan, Chee Hing

    2011-11-01

    The evolution of the dark currents and breakdown at elevated temperatures of up to 450  K are studied using thin AlAsSb avalanche regions. While the dark currents increase rapidly as the temperature is increased, the avalanche gain is shown to only have a weak temperature dependence. Temperature coefficients of breakdown voltage of 0.93 and 1.93  mV/K were obtained from the diodes of 80 and 230  nm avalanche regions (i-regions), respectively. These values are significantly lower than for other available avalanche materials at these temperatures. The wavelength dependence of multiplication characteristics of AlAsSb p-i-n diodes has also been investigated, and it was found that the ionization coefficients for electrons and holes are comparable within the electric field and wavelength ranges measured.

  2. CMS Resistive plate Champers

    CERN Document Server

    Zainab, Karam

    2013-01-01

    There are many types of gas detectors which are used in CERN in LHC project, There is a main parts for the gas detectors which must be in all gas detectors types like Multiwire proportional chambers, such as the micromesh gaseous structure chamber (the MicroMegas), Gas-electron multiplier (GEM) detector, Resistive Plate Champers... Compact Muon Solenoid (CMS) experiment detecting muons which are powerful tool for recognizing signatures of interesting physics processes. The CMS detector uses: drift tube (DT), cathode strip chamber (CSC) and resistive plate chamber (RPC). Building RPC’s was my project in summer student program (hardware). RPC’s have advantages which are triggering detector and Excellent time resolution which reinforce the measurement of the correct beam crossing time. RPC’s Organized in stations :  RPC barrel (RB) there are 4 stations, namely RB1, RB2, RB3, and RB4  While in the RPC endcap (RE) the 3 stations are RE1, RE2, and RE3. In the endcaps a new starion will be added and this...

  3. Commercially available Geiger mode single-photon avalanche photodiode with a very low afterpulsing probability

    CERN Document Server

    Stipčević, Mario

    2015-01-01

    Afterpulsing is one of the main technological flaws present in photon counting detectors based on solid-state semiconductor avalanche photodiodes operated in Geiger mode. Level of afterpulsing depends mainly on type of the semiconductor, doping concentrations and temperature and presents an additional source of noise, along with dark counts. Unlike dark counts which appear randomly in time, aterpulses and are time-correlated with the previous detections. For measurements that rely on timing information afterpulsing can create fake signals and diminish the sensitivity. In this work we test a novel broadband sensitive APD that was designed for sub-Geiger avalanche gain operation. We find that this APD, which has a reach-through geometry typical of single-photon detection photodiodes, can also operate in Geiger mode with usable detection sensitivity and acceptable dark counts level while exhibiting uniquely low afterpulsing. The afterpulsing of tested samples was systematically less than 0.05 percent at 10V exce...

  4. Pixelated Geiger-Mode Avalanche Photo-Diode Characterization through Dark Current Measurement

    CERN Document Server

    Amaudruz, Pierre-André; Gilhully, Colleen; Goertzen, Andrew; James, Lloyd; Kozlowski, Piotr; Retière, Fabrice; Shams, Ehsan; Sossi, Vesna; Stortz, Greg; Thiessen, Jonathan D; Thompson, Christopher J

    2013-01-01

    PIXELATED geiger-mode avalanche photodiodes(PPDs), often called silicon photomultipliers (SiPMs) are emerging as an excellent replacement for traditional photomultiplier tubes (PMTs) in a variety of detectors, especially those for subatomic physics experiments, which requires extensive test and operation procedures in order to achieve uniform responses from all the devices. In this paper, we show for two PPD brands, Hamamatsu MPPC and SensL SPM, that the dark noise rate, breakdown voltage and rate of correlated avalanches can be inferred from the sole measure of dark current as a function of operating voltage, hence greatly simplifying the characterization procedure. We introduce a custom electronics system that allows measurement for many devices concurrently, hence allowing rapid testing and monitoring of many devices at low cost. Finally, we show that the dark current of Hamamastu Multi-Pixel Photon Counter (MPPC) is rather independent of temperature at constant operating voltage, hence the current measure...

  5. The performance of photon counting imaging with a Geiger mode silicon avalanche photodiode

    Science.gov (United States)

    Qu, Hui-Ming; Zhang, Yi-Fan; Ji, Zhong-Jie; Chen, Qian

    2013-10-01

    In principle, photon counting imaging can detect a photon. With the development of low-level-light image intensifier techniques and low-level-light detection devices, photon counting imaging can now detect photon images under extremely low illumination. Based on a Geiger mode silicon avalanche photodiode single photon counter, an experimental system for photon counting imaging was built through two-dimensional scanning of a SPAD (single photon avalanche diode) detector. The feasibility of the imaging platform was validated experimentally. Two images with different characteristics, namely, the USAF 1951 resolution test panel and the image of Lena, were chosen to evaluate the imaging performance of the experimental system. The results were compared and analysed. The imaging properties under various illumination and scanning steps were studied. The lowest illumination limit of the SPAD photon counting imaging was determined.

  6. The design of the TASD (totally active scintillator detector) prototype

    Energy Technology Data Exchange (ETDEWEB)

    Mefodiev, A. V., E-mail: Mefodiev@inr.ru; Kudenko, Yu. G. [Moscow Institute of Physics and Technology (State University) (Russian Federation)

    2015-12-15

    Totally active and magnetic segmented scintillation neutrino detectors are developed for the nextgeneration accelerator neutrino experiments. Such detectors will incorporate scintillation modules with scintillation counters that form X and Y planes. A single counter is a 7 × 10 × 90 mm{sup 3} scintillation bar with gluedin wavelength-shifting fibers and micropixel avalanche photodiodes. The results of measurements of the parameters of these detectors are presented.

  7. Status and perspectives of solid state photon detectors

    Energy Technology Data Exchange (ETDEWEB)

    Korpar, Samo, E-mail: Samo.Korpar@ijs.s [Faculty of Chemistry and Chemical Engineering, University of Maribor, Smetanova 17, SI-2000 Maribor (Slovenia); Jozef Stefan Institute, Jamova cesta 39, SI-1000 Ljubljana (Slovenia)

    2011-05-21

    Recent years have seen a considerable progress in the development of solid state photon detectors. In particular it is the Geiger mode avalanche photodiode, also known as the silicon photomultiplier (SiPM), which is much investigated for its single photon sensitivity as well as its other appealing properties. In the present paper we discuss the recent advances of such photon detectors as well as possibilities for their application, mainly in ring imaging Cherenkov detectors.

  8. Interplanetary Space Weather Effects on Lunar Reconnaissance Orbiter Avalanche Photodiode Performance

    Science.gov (United States)

    Clements, E. B.; Carlton, A. K.; Joyce, C. J.; Schwadron, N. A.; Spence, H. E.; Sun, X.; Cahoy, K.

    2016-01-01

    Space weather is a major concern for radiation-sensitive space systems, particularly for interplanetary missions, which operate outside of the protection of Earth's magnetic field. We examine and quantify the effects of space weather on silicon avalanche photodiodes (SiAPDs), which are used for interplanetary laser altimeters and communications systems and can be sensitive to even low levels of radiation (less than 50 cGy). While ground-based radiation testing has been performed on avalanche photodiode (APDs) for space missions, in-space measurements of SiAPD response to interplanetary space weather have not been previously reported. We compare noise data from the Lunar Reconnaissance Orbiter (LRO) Lunar Orbiter Laser Altimeter (LOLA) SiAPDs with radiation measurements from the onboard Cosmic Ray Telescope for the Effects of Radiation (CRaTER) instrument. We did not find any evidence to support radiation as the cause of changes in detector threshold voltage during radiation storms, both for transient detector noise and long-term average detector noise, suggesting that the approximately 1.3 cm thick shielding (a combination of titanium and beryllium) of the LOLA detectors is sufficient for SiAPDs on interplanetary missions with radiation environments similar to what the LRO experienced (559 cGy of radiation over 4 years).

  9. Interplanetary Space Weather Effects on Lunar Reconnaissance Orbiter Avalanche Photodiode Performance

    Science.gov (United States)

    Clements, E. B.; Carlton, A. K.; Joyce, C. J.; Schwadron, N. A.; Spence, H. E.; Sun, X.; Cahoy, K.

    2016-01-01

    Space weather is a major concern for radiation-sensitive space systems, particularly for interplanetary missions, which operate outside of the protection of Earth's magnetic field. We examine and quantify the effects of space weather on silicon avalanche photodiodes (SiAPDs), which are used for interplanetary laser altimeters and communications systems and can be sensitive to even low levels of radiation (less than 50 cGy). While ground-based radiation testing has been performed on avalanche photodiode (APDs) for space missions, in-space measurements of SiAPD response to interplanetary space weather have not been previously reported. We compare noise data from the Lunar Reconnaissance Orbiter (LRO) Lunar Orbiter Laser Altimeter (LOLA) SiAPDs with radiation measurements from the onboard Cosmic Ray Telescope for the Effects of Radiation (CRaTER) instrument. We did not find any evidence to support radiation as the cause of changes in detector threshold voltage during radiation storms, both for transient detector noise and long-term average detector noise, suggesting that the approximately 1.3 cm thick shielding (a combination of titanium and beryllium) of the LOLA detectors is sufficient for SiAPDs on interplanetary missions with radiation environments similar to what the LRO experienced (559 cGy of radiation over 4 years).

  10. Nano-multiplication region avalanche photodiodes and arrays

    Science.gov (United States)

    Zheng, Xinyu (Inventor); Pain, Bedabrata (Inventor); Cunningham, Thomas J. (Inventor)

    2011-01-01

    An avalanche photodiode with a nano-scale reach-through structure comprising n-doped and p-doped regions, formed on a silicon island on an insulator, so that the avalanche photodiode may be electrically isolated from other circuitry on other silicon islands on the same silicon chip as the avalanche photodiode. For some embodiments, multiplied holes generated by an avalanche reduces the electric field in the depletion region of the n-doped and p-doped regions to bring about self-quenching of the avalanche photodiode. Other embodiments are described and claimed.

  11. The avalanche-mode superjunction LED

    NARCIS (Netherlands)

    Dutta, Satadal; Steeneken, Peter G.; Agarwal, Vishal Vishal; Schmitz, Jurriaan; Annema, Anne J.; Hueting, Raymond Josephus Engelbart

    2017-01-01

    Avalanche-mode light-emitting diodes (AMLEDs) in silicon (Si) are potential light sources to enable monolithic optical links in standard CMOS technology, due to the large overlap of their electroluminescent (EL) spectra with the responsivity of Si photodiodes. These EL spectra depend on the reverse

  12. Measuring acoustic emissions in an avalanche slope

    Science.gov (United States)

    Reiweger, Ingrid; Schweizer, Jürg

    2014-05-01

    Measurements of acoustic emissions are a common technique for monitoring damage and predicting imminent failure of a material. Within natural hazards it has already been used to successfully predict the break-off of a hanging glacier. To explore the applicability of the acoustic emission (AE) technique for avalanche prediction, we installed two acoustic sensors (with 30 kHz and 60 kHz resonance frequency) in an avalanche prone slope at the Mittelgrat in the Parsenn ski area above Davos, Switzerland. The slope is north-east facing, frequently wind loaded, and approximately 35° steep. The AE signals - in particular the event energy and waiting time distributions - were compared with slope stability. The latter was determined by observing avalanche activity. The results of two winter's measurements yielded that the exponent β of the inverse cumulative distribution of event energy showed a significant drop (from a value of 3.5 to roughly 2.5) at very unstable conditions, i.e. on the three days during our measurement periods when spontaneous avalanches released on our study slope.

  13. Characterization of Advanced Avalanche Photodiodes for Water Vapor Lidar Receivers

    Science.gov (United States)

    Refaat, Tamer F.; Halama, Gary E.; DeYoung, Russell J.

    2000-01-01

    Development of advanced differential absorption lidar (DIAL) receivers is very important to increase the accuracy of atmospheric water vapor measurements. A major component of such receivers is the optical detector. In the near-infrared wavelength range avalanche photodiodes (APD's) are the best choice for higher signal-to-noise ratio, where there are many water vapor absorption lines. In this study, characterization experiments were performed to evaluate a group of silicon-based APD's. The APD's have different structures representative of different manufacturers. The experiments include setups to calibrate these devices, as well as characterization of the effects of voltage bias and temperature on the responsivity, surface scans, noise measurements, and frequency response measurements. For each experiment, the setup, procedure, data analysis, and results are given and discussed. This research was done to choose a suitable APD detector for the development of an advanced atmospheric water vapor differential absorption lidar detection system operating either at 720, 820, or 940 nm. The results point out the benefits of using the super low ionization ratio (SLIK) structure APD for its lower noise-equivalent power, which was found to be on the order of 2 to 4 fW/Hz(sup (1/2)), with an appropriate optical system and electronics. The water vapor detection systems signal-to-noise ratio will increase by a factor of 10.

  14. Recent advances in very large area avalanche photodiodes

    Science.gov (United States)

    Squillante, Michael R.; Christian, James; Entine, Gerald; Farrell, Richard; Karger, Arieh M.; McClish, Mickel; Myers, Richard; Shah, Kanai S.; Taylor, David; Vanderpuye, Kofi; Waer, Peter; Woodring, Mitchell

    2003-09-01

    The Avalanche Photodiode (APD) is a unique device that combines the advantages of solid state photodetectors with those of high gain devices such as photomultiplier tubes (PMTs). APDs have internal gain that provides a high signal-to-noise ratio. APDs have high quantum efficiency, are fast, compact, and rugged. These properties make them suitable detectors for important applications such as LADAR, detection and identification toxic chemicals and bio-warfare agents, LIDAR fluorescence detection, stand-off laser induced breakdown spectroscopy (LIBS), and nuclear detectors and imagers. Recently there have been significant technical breakthroughs in fabricating very large APDs, APD arrays, and position sensitive APD arrays (PSAPD). Signal gain of over 10,000 has been achieved, single element APDs have been fabricated with active area greater than 40 cm2, monolithic pixelated arrays with up to 28 x 28 elements have been fabricated, and position sensitive APDs have been developed and tested. Additionally, significant progress has been made in improving the fabrication process to provide better uniformity and high yield, permitting cost effective manufacturing of APDs for reduced cost.

  15. Development of the Pixelated Photon Detector Using Silicon on Insulator Technology for TOF-PET

    CERN Document Server

    Koyama, Akihiro; Takahashi, Hiroyuki; Orita, Tadashi; Arai, Yasuo; Kurachi, Ikuo; Miyoshi, Toshinobu; Nio, Daisuke; Hamasaki, Ryutaro

    2015-01-01

    To measure light emission pattern in scintillator, higher sensitivity and faster response are required to photo detector. Such as single photon avalanche diode (SPAD), conventional pixelated photo detector is operated at Geiger avalanche multiplication. However higher gain of SPAD seems very attractive, photon detection efficiency per unit area is low. This weak point is mainly caused by Geiger avalanche mechanism. To overcome these difficulties, we designed Pixelated Linear Avalanche Integration Detector using Silicon on Insulator technology (SOI-Plaid). To avoid dark count noise and dead time comes from quench circuit, we are planning to use APD in linear multiplication mode. SOI technology enables laminating readout circuit and APD layer, and high-speed and low-noise signal reading regardless smaller gain of linear APD. This study shows design of linear APD by using SOI fabrication process. We designed test element group (TEG) of linear APD and inspected optimal structure of linear APD.

  16. Simulations of avalanche breakdown statistics: probability and timing

    Science.gov (United States)

    Ng, Jo Shien; Tan, Chee Hing; David, John P. R.

    2010-04-01

    Important avalanche breakdown statistics for Single Photon Avalanche Diodes (SPADs), such as avalanche breakdown probability, dark count rate, and the distribution of time taken to reach breakdown (providing mean time to breakdown and jitter), were simulated. These simulations enable unambiguous studies on effects of avalanche region width, ionization coefficient ratio and carrier dead space on the avalanche statistics, which are the fundamental limits of the SPADs. The effects of quenching resistor/circuit have been ignored. Due to competing effects between dead spaces, which are significant in modern SPADs with narrow avalanche regions, and converging ionization coefficients, the breakdown probability versus overbias characteristics from different avalanche region widths are fairly close to each other. Concerning avalanche breakdown timing at given value of breakdown probability, using avalanche material with similar ionization coefficients yields fast avalanche breakdowns with small timing jitter (albeit higher operating field), compared to material with dissimilar ionization coefficients. This is the opposite requirement for abrupt breakdown probability versus overbias characteristics. In addition, by taking band-to-band tunneling current (dark carriers) into account, minimum avalanche region width for practical SPADs was found to be 0.3 and 0.2 μm, for InP and InAlAs, respectively.

  17. Readout electronics for low dark count Geiger mode avalanche photodiodes fabricated in conventional HV-CMOS technologies for future linear colliders

    Energy Technology Data Exchange (ETDEWEB)

    Vilella, E; Arbat, A; Alonso, O; Vila, A; Dieguez, A [Department of Electronics, University of Barcelona (UB) MartI i Franques 1, 08028 Barcelona (Spain); Comerma, A; Trenado, J; Gascon, D; Garrido, L, E-mail: evilella@el.ub.es [Department of Structure and Constituents of Matter, University of Barcelona (UB) MartI i Franques 1, 08028 Barcelona (Spain)

    2011-01-15

    This work presents low noise readout circuits for silicon pixel detectors based on Geiger mode avalanche photodiodes. Geiger mode avalanche photodiodes offer a high intrinsic gain as well as an excellent timing accuracy. In addition, they can be compatible with standard CMOS technologies. However, they suffer from a high intrinsic noise, which induces false counts indistinguishable from real events and represents an increase of the readout electronics area to store the false counts. We have developed new front-end electronic circuitry for Geiger mode avalanche photodiodes in a conventional 0.35 {mu}m HV-CMOS technology based on a gated mode of operation that allows low noise operation. The performance of the pixel detector is triggered and synchronized with the particle beam thanks to the gated acquisition. The circuits allow low reverse bias overvoltage operation which also improves the noise figures. Experimental characterization of the fabricated front-end circuit is presented in this work.

  18. Gravitational wet-avalanche pressure on pylon-like structures

    Science.gov (United States)

    Sovilla, Betty; Faug, Thierry; Köhler, Anselm; Baroudi, Djebar; Fischer, Jan-Thomas; Thibert, Emmanuel

    2016-04-01

    Low-speed wet-avalanches exert hydrostatic forces on structures which are surface-dependent, however neither the pressure amplification experienced by smaller structure has been quantified and the causes of the amplification understood. In particular, recent wet-snow avalanche pressure measurements, performed with small cells at the "Vallée the la Sionne" test site, indicate significantly higher pressures than those considered by engineering guidelines and common practice rules based only on the contribution of inertial forces. In order to gain a deeper understanding and investigate the relevance of these measurements for structural design, we analyze data collected at the "Vallée the la Sionne" on obstacles of different shapes and dimensions. We show that, the pressure measured on a 1 m2 pressure plate is, on average, 1.8 times smaller than the pressure measured on a 0.008 m2 piezoelectric cell, installed on a 0.60 m wide pylon, and 2.9 times smaller than the pressure measured on a 0.0125 m2 cantilever sensor, extending freely into the snow. The different pressures encountered by the different obstacles is quantitatively explained with a granular force model, assuming the formation of a mobilized volume of snow granules extending from the obstacle upstream. The results underscore the fundamental influence of the dimension of the sensor and the obstacle on pressures. Our study highlights the difficulties that appear in the estimation of forces in the gravitational flow regime, for which force amplification may be caused by this mobilized volume at the scale of the whole structure, but also by plastic wedges, or small dead zones, at the scale of the sensor mounted on a wider structure.

  19. 30 CFR 22.10 - Approval plate.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Approval plate. 22.10 Section 22.10 Mineral... MINING PRODUCTS PORTABLE METHANE DETECTORS § 22.10 Approval plate. (a) Attachment to be made by manufacturers. (1) Manufacturers shall attach, stamp, or mold an approval plate on each permissible methane...

  20. Investigation of spatial resolution and temporal performance of SAPHIRE (scintillator avalanche photoconductor with high resolution emitter readout) with integrated electrostatic focusing

    Science.gov (United States)

    Scaduto, David A.; Lubinsky, Anthony R.; Rowlands, John A.; Kenmotsu, Hidenori; Nishimoto, Norihito; Nishino, Takeshi; Tanioka, Kenkichi; Zhao, Wei

    2014-03-01

    We have previously proposed SAPHIRE (scintillator avalanche photoconductor with high resolution emitter readout), a novel detector concept with potentially superior spatial resolution and low-dose performance compared with existing flat-panel imagers. The detector comprises a scintillator that is optically coupled to an amorphous selenium photoconductor operated with avalanche gain, known as high-gain avalanche rushing photoconductor (HARP). High resolution electron beam readout is achieved using a field emitter array (FEA). This combination of avalanche gain, allowing for very low-dose imaging, and electron emitter readout, providing high spatial resolution, offers potentially superior image quality compared with existing flat-panel imagers, with specific applications to fluoroscopy and breast imaging. Through the present collaboration, a prototype HARP sensor with integrated electrostatic focusing and nano- Spindt FEA readout technology has been fabricated. The integrated electron-optic focusing approach is more suitable for fabricating large-area detectors. We investigate the dependence of spatial resolution on sensor structure and operating conditions, and compare the performance of electrostatic focusing with previous technologies. Our results show a clear dependence of spatial resolution on electrostatic focusing potential, with performance approaching that of the previous design with external mesh-electrode. Further, temporal performance (lag) of the detector is evaluated and the results show that the integrated electrostatic focusing design exhibits comparable or better performance compared with the mesh-electrode design. This study represents the first technical evaluation and characterization of the SAPHIRE concept with integrated electrostatic focusing.

  1. Memory effect in silicon time-gated single-photon avalanche diodes

    Energy Technology Data Exchange (ETDEWEB)

    Dalla Mora, A.; Contini, D., E-mail: davide.contini@polimi.it; Di Sieno, L. [Dipartimento di Fisica, Politecnico di Milano, Piazza Leonardo da Vinci 32, I-20133 Milano (Italy); Tosi, A.; Boso, G.; Villa, F. [Dipartimento di Elettronica, Informazione e Bioingegneria, Politecnico di Milano, Piazza Leonardo da Vinci 32, I-20133 Milano (Italy); Pifferi, A. [Dipartimento di Fisica, Politecnico di Milano, Piazza Leonardo da Vinci 32, I-20133 Milano (Italy); CNR, Istituto di Fotonica e Nanotecnologie, Piazza Leonardo da Vinci 32, I-20133 Milano (Italy)

    2015-03-21

    We present a comprehensive characterization of the memory effect arising in thin-junction silicon Single-Photon Avalanche Diodes (SPADs) when exposed to strong illumination. This partially unknown afterpulsing-like noise represents the main limiting factor when time-gated acquisitions are exploited to increase the measurement dynamic range of very fast (picosecond scale) and faint (single-photon) optical signals following a strong stray one. We report the dependences of this unwelcome signal-related noise on photon wavelength, detector temperature, and biasing conditions. Our results suggest that this so-called “memory effect” is generated in the deep regions of the detector, well below the depleted region, and its contribution on detector response is visible only when time-gated SPADs are exploited to reject a strong burst of photons.

  2. Temporal and spatial multiplexed infrared single-photon counter based on high-speed avalanche photodiode

    Science.gov (United States)

    Chen, Xiuliang; Ding, Chengjie; Pan, Haifeng; Huang, Kun; Laurat, Julien; Wu, Guang; Wu, E.

    2017-03-01

    We report on a high-speed temporal and spatial multiplexed single-photon counter with photon-number-resolving capability up to four photons. The infrared detector combines a fiber loop to split, delay and recombine optical pulses and a 200 MHz dual-channel single-photon detector based on InGaAs/InP avalanche photodiode. To fully characterize the photon-number-resolving capability, we perform quantum detector tomography and then reconstruct its positive-operator-valued measure and the associated Wigner functions. The result shows that, despite of the afterpulsing noise and limited system detection efficiency, this temporal and spatial multiplexed single-photon counter can already find applications for large repetition rate quantum information schemes.

  3. Temporal and spatial multiplexed infrared single-photon counter based on high-speed avalanche photodiode

    Science.gov (United States)

    Chen, Xiuliang; Ding, Chengjie; Pan, Haifeng; Huang, Kun; Laurat, Julien; Wu, Guang; Wu, E

    2017-01-01

    We report on a high-speed temporal and spatial multiplexed single-photon counter with photon-number-resolving capability up to four photons. The infrared detector combines a fiber loop to split, delay and recombine optical pulses and a 200 MHz dual-channel single-photon detector based on InGaAs/InP avalanche photodiode. To fully characterize the photon-number-resolving capability, we perform quantum detector tomography and then reconstruct its positive-operator-valued measure and the associated Wigner functions. The result shows that, despite of the afterpulsing noise and limited system detection efficiency, this temporal and spatial multiplexed single-photon counter can already find applications for large repetition rate quantum information schemes. PMID:28294155

  4. Investigation of Ion Backflow in Bulk Micromegas Detectors

    CERN Document Server

    Bhattacharya, Purba; Mukhopadhyay, Supratik; Bhattacharya, Sudeb; Majumdar, Nayana; Sarkar, Sandip; Colas, Paul; Attie, David

    2016-01-01

    The operation of gas detectors is often limited by secondary effects, originating from avalanche-induced photons and ions. Ion backflow is one of the effects limiting the operation of a gas detector at high flux, by giving rise to space charge which disturbs the electric field locally. For the Micromegas detector, a large fraction of the secondary positive ions created in the avalanche can be stopped at the micro-mesh. The present work involves measurements of the ion backflow fraction (using an experimental setup comprising of two drift planes) in bulk Micromegas detectors as a function of detector design parameters. These measured characteristics have also been compared in detail to numerical simulations using the Garfield framework that combines packages such as neBEM, Magboltz and Heed. Further, the effect of using a second micro-mesh on ion backflow and other parameters has been studied numerically.

  5. Nearest neighbour models for local and regional avalanche forecasting

    Directory of Open Access Journals (Sweden)

    M. Gassner

    2002-01-01

    Full Text Available This paper presents two avalanche forecasting applications NXD2000 and NXD-REG which were developed at the Swiss Federal Institute for Snow and Avalanche Re-search (SLF. Even both are based on the nearest neighbour method they are targeted to different scales. NXD2000 is used to forecast avalanches on a local scale. It is operated by avalanche forecasters responsible for snow safety at snow sport areas, villages or cross country roads. The area covered ranges from 10 km2 up to 100 km2 depending on the climatological homogeneity. It provides the forecaster with ten most similar days to a given situation. The observed avalanches of these days are an indication of the actual avalanche danger. NXD-REG is used operationally by the Swiss avalanche warning service for regional avalanche forecasting. The Nearest Neighbour approach is applied to the data sets of 60 observer stations. The results of each station are then compiled into a map of current and future avalanche hazard. Evaluation of the model by cross-validation has shown that the model can reproduce the official SLF avalanche forecasts in about 52% of the days.

  6. A new experimental site for the study of snow avalanches in the Aosta Valley (NW-Italy)

    Science.gov (United States)

    Segor, Valerio; Barbero, Monica; Barpi, Fabrizio; Borri Brunetto, Mauro; Bovet, Eloise; Brulport, Antoine; Ceaglio, Elisabetta; Chiaia, Bernardino; Fassin, Daniele; Freppaz, Michele; Frigo, Barbara; Godone, Danilo; Maggioni, Margherita; Pallara, Oronzo; Torretta, Franco; Viglietti, Davide; Welf, Arnoldo

    2010-05-01

    slope, to measure the snow properties in the release zone, to perimeter the avalanche outline, to dig profiles of the avalanche deposit. To detect the behavior of structures impacted by avalanches and their influence on the snow flow, the test site will be equipped with an instrumented obstacle. The galvanized steel obstacle is composed of two masts whose height is about 4 m that support instrumented horizontal plates for measuring the impact forces. The plates can be separately positioned at different levels or grouped together to form a panel with area of 1m2. The exact positioning of the obstacle is one of the goals of the first experiments for winter 2009/2010, as well as the calibration of the sensors and the study of the behavior of the obstacle under different loads in the laboratory. The obstacle will be built in summer 2010. The data (impact forces, pressures, accelerations, etc…) will be continuously acquired and transmitted via optical fiber to a control room remotely located. All the activities will be conducted according to an operational plan, which governs all the different steps of an experiment: from the alert system, to the role of each operator during the experiment, to the security plan.

  7. Time-resolved non-contact fluorescence diffuse optical tomography measurements with ultra-fast time-correlated single photon counting avalanche photodiodes

    Science.gov (United States)

    Bérubé-Lauzière, Yves; Robichaud, Vincent; Lapointe, Éric

    2007-07-01

    The design and fabrication of time-correlated single photon counting (TCSPC) avalanche photodiodes (APDs) and associated quenching circuits have made significant progresses in recent years. APDs with temporal resolutions comparable to microchannel plate photomultiplier tubes (MCP-PMTs) are now available. MCP-PMTs were until these progresses the best TCSPC detectors with timing resolutions down to 30ps. APDs can now achieve these resolutions at a fraction of the cost. Work is under way to make the manufacturing of TCSPC APDs compatible with standard electronics fabrication practices. This should allow to further reduce their cost and render them easier to integrate in complex multi-channel TCSPC electronics, as needed in diffuse optical tomography (DOT) systems. Even if their sensitive area is much smaller than that of the ubiquitous PMT used in TCSPC, we show that with appropriate selection of optical components, TCSPC APDs can be used in time-domain DOT. To support this, we present experimental data and calculations clearly demonstrating that comparable measurements can be obtained with APDs and PMTs. We are, to our knowledge, the first group using APDs in TD DOT, in particular in non-contact TD fluorescence DOT.

  8. Note: Fully integrated active quenching circuit achieving 100 MHz count rate with custom technology single photon avalanche diodes

    Science.gov (United States)

    Acconcia, G.; Labanca, I.; Rech, I.; Gulinatti, A.; Ghioni, M.

    2017-02-01

    The minimization of Single Photon Avalanche Diodes (SPADs) dead time is a key factor to speed up photon counting and timing measurements. We present a fully integrated Active Quenching Circuit (AQC) able to provide a count rate as high as 100 MHz with custom technology SPAD detectors. The AQC can also operate the new red enhanced SPAD and provide the timing information with a timing jitter Full Width at Half Maximum (FWHM) as low as 160 ps.

  9. 1.5 GHz single-photon detection at telecommunication wavelengths using sinusoidally gated InGaAs/InP avalanche photodiode.

    Science.gov (United States)

    Namekata, Naoto; Adachi, Shunsuke; Inoue, Shuichiro

    2009-04-13

    We report a telecom-band single-photon detector for gigahertz clocked quantum key distribution systems. The single-photon detector is based on a sinusoidally gated InGaAs/InP avalanche photodiode. The gate repetition frequency of the single-photon detector reached 1.5 GHz. A quantum efficiency of 10.8 % at 1550 nm was obtained with a dark count probability per gate of 6.3 x 10(-7) and an afterpulsing probability of 2.8 %. Moreover, the maximum detection rate of the detector is 20 MHz.

  10. SAPHIRE (scintillator avalanche photoconductor with high resolution emitter readout) for low dose x-ray imaging: spatial resolution.

    Science.gov (United States)

    Li, Dan; Zhao, Wei

    2008-07-01

    An indirect flat panel imager (FPI) with programmable avalanche gain and field emitter array (FEA) readout is being investigated for low-dose and high resolution x-ray imaging. It is made by optically coupling a structured x-ray scintillator, e.g., thallium (Tl) doped cesium iodide (CsI), to an amorphous selenium (a-Se) avalanche photoconductor called high-gain avalanche rushing amorphous photoconductor (HARP). The charge image created by the scintillator/HARP (SHARP) combination is read out by the electron beams emitted from the FEA. The proposed detector is called scintillator avalanche photoconductor with high resolution emitter readout (SAPHIRE). The programmable avalanche gain of HARP can improve the low dose performance of indirect FPI while the FEA can be made with pixel sizes down to 50 microm. Because of the avalanche gain, a high resolution type of CsI (Tl), which has not been widely used in indirect FPI due to its lower light output, can be used to improve the high spatial frequency performance. The purpose of the present article is to investigate the factors affecting the spatial resolution of SAPHIRE. Since the resolution performance of the SHARP combination has been well studied, the focus of the present work is on the inherent resolution of the FEA readout method. The lateral spread of the electron beam emitted from a 50 microm x 50 microm pixel FEA was investigated with two different electron-optical designs: mesh-electrode-only and electrostatic focusing. Our results showed that electrostatic focusing can limit the lateral spread of electron beams to within the pixel size of down to 50 microm. Since electrostatic focusing is essentially independent of signal intensity, it will provide excellent spatial uniformity.

  11. Fractal properties of LED avalanche breakdown

    Directory of Open Access Journals (Sweden)

    Antonina S. Shashkina

    2016-12-01

    Full Text Available The conventional model of the processes occurring in the course of a p–n-junction's partial avalanche breakdown has been analyzed in this paper. Microplasma noise spectra of industrially produced LEDs were compared with those predicted by the model. It was established that the data obtained experimentally on reverse-biased LEDs could not be described in terms of this model. The degree to which the fractal properties were pronounced was shown to be variable by changing the reverse voltage. The discovered fractal properties of microplasma noise can serve as the basis for further studies which are bound to explain the breakdown characteristics of real LEDs and to correct the conventional model of p–n-junction's avalanche breakdown.

  12. Do Neural Avalanches Indicate Criticality After All?

    CERN Document Server

    Dehghani, Mohammad; Shahbazi, Farhad

    2016-01-01

    Neural avalanches in size and duration exhibit a power law distribution illustrating as a straight line when plotted on the logarithmic scales. The power-law exponent is interpreted as the signature of criticality and it is assumed that the resting brain operates near criticality. However, there is no clear evidence that supports this assumption, and even there are extensive research studies conflicting one another. The model of the current paper is an extension of a previous publication wherein we used an integrate-and-fire model on a regular lattice with periodic boundary conditions and introduced the temporal complexity as a genuine signature of criticality. However, in that model the power-law distribution of neural avalanches were manifestation of super-criticality rather than criticality. Here, however, we show that replacing the discrete noise in the model with a Gaussian noise and continuous time solution of the equation leads to coincidence of temporal complexity and spatiotemporal patterns of neural...

  13. Shot noise suppression in avalanche photodiodes.

    Science.gov (United States)

    Ma, Feng; Wang, Shuling; Campbell, Joe C

    2005-10-21

    We identify a new shot noise suppression mechanism in a thin (approximately 100 nm) heterostructure avalanche photodiode. In the low-gain regime the shot noise is suppressed due to temporal correlations within amplified current pulses. We demonstrate in a Monte Carlo simulation that the effective excess noise factors can be < 1, and reconcile the apparent conflict between theory and experiments. This shot noise suppression mechanism is independent of known mechanisms such as Coulomb interaction, or reflection at heterojunction interfaces.

  14. State-of-the-art performance of GaAlAs/GaAs avalanche photodiodes

    Science.gov (United States)

    Law, H. D.; Nakano, K.; Tomasetta, L. R.

    1979-01-01

    Ga(0.15)Al(0.85)As/GaAs avalanche photodiodes have been successfully fabricated. The performance of these detectors is characterized by a rise time of less than 35 ps, an external quantum efficiency with an antireflection coating of 95% at 0.53 microns, and a microwave optical gain of 42 dB. The dark current density is in the low range (10 to the minus A/sq cm) at one-half the breakdown voltages, and rises to 0.0001 A/sq cm at 42 dB optical gain.

  15. Neuronal avalanches in spontaneous activity in vivo.

    Science.gov (United States)

    Hahn, Gerald; Petermann, Thomas; Havenith, Martha N; Yu, Shan; Singer, Wolf; Plenz, Dietmar; Nikolic, Danko

    2010-12-01

    Many complex systems give rise to events that are clustered in space and time, thereby establishing a correlation structure that is governed by power law statistics. In the cortex, such clusters of activity, called "neuronal avalanches," were recently found in local field potentials (LFPs) of spontaneous activity in acute cortex slices, slice cultures, the developing cortex of the anesthetized rat, and premotor and motor cortex of awake monkeys. At present, it is unclear whether neuronal avalanches also exist in the spontaneous LFPs and spike activity in vivo in sensory areas of the mature brain. To address this question, we recorded spontaneous LFPs and extracellular spiking activity with multiple 4 × 4 microelectrode arrays (Michigan Probes) in area 17 of adult cats under anesthesia. A cluster of events was defined as a consecutive sequence of time bins Δt (1-32 ms), each containing at least one LFP event or spike anywhere on the array. LFP cluster sizes consistently distributed according to a power law with a slope largely above -1.5. In two thirds of the corresponding experiments, spike clusters also displayed a power law that displayed a slightly steeper slope of -1.8 and was destroyed by subsampling operations. The power law in spike clusters was accompanied with stronger temporal correlations between spiking activities of neurons that spanned longer time periods compared with spike clusters lacking power law statistics. The results suggest that spontaneous activity of the visual cortex under anesthesia has the properties of neuronal avalanches.

  16. Edge effect on the power law distribution of granular avalanches.

    Science.gov (United States)

    Lorincz, Kinga A; Wijngaarden, Rinke J

    2007-10-01

    Many punctuated phenomena in nature are claimed [e.g., by the theory of self-organized criticality (SOC)] to be power-law distributed. In our experiments on a three-dimensional pile of long-grained rice, we find that by only changing the boundary condition of the system, we switch from such power-law-distributed avalanche sizes to quasiperiodic system-spanning avalanches. Conversely, by removing ledges the incidence of system-spanning avalanches is significantly reduced. This may offer a perspective on new avalanche prevention schemes. In addition, our findings may help to explain why the archetype of SOC, the sandpile, was found to have power-law-distributed avalanches in some experiments, while in other experiments quasiperiodic system-spanning avalanches were found.

  17. Monte Carlo investigation of avalanche multiplication process in thin InP avalanche photodiodes

    Institute of Scientific and Technical Information of China (English)

    WANG Gang; MA YuXiang

    2009-01-01

    An ensemble Monte Carlo simulation is presented to investigate the avalanche multiplication process in thin InP avalanche photodiodes (APDs). Analytical band structures are applied to the description of the conduction and valence band, and impact ionization is treated as an additional scattering mecha-nism with the Keldysh formula. Multiplication gain and excess noise factor of InP p~+-i-n~+ APDs aresimulated and obvious excess noise reduction is found in the thinner devices. The effect of dead space on excess noise in thin APD structures is investigated by the distribution of impact ionization events within the multiplication region. It is found that the dead space can suppress the feedback ionization events resulting in a more deterministic avalanche multiplication process and reduce the excess noise in thinner APDs.

  18. Pixelated neutron image plates

    Science.gov (United States)

    Schlapp, M.; Conrad, H.; von Seggern, H.

    2004-09-01

    Neutron image plates (NIPs) have found widespread application as neutron detectors for single-crystal and powder diffraction, small-angle scattering and tomography. After neutron exposure, the image plate can be read out by scanning with a laser. Commercially available NIPs consist of a powder mixture of BaFBr : Eu2+ and Gd2O3 dispersed in a polymer matrix and supported by a flexible polymer sheet. Since BaFBr : Eu2+ is an excellent x-ray storage phosphor, these NIPs are particularly sensitive to ggr-radiation, which is always present as a background radiation in neutron experiments. In this work we present results on NIPs consisting of KCl : Eu2+ and LiF that were fabricated into ceramic image plates in which the alkali halides act as a self-supporting matrix without the necessity for using a polymeric binder. An advantage of this type of NIP is the significantly reduced ggr-sensitivity. However, the much lower neutron absorption cross section of LiF compared with Gd2O3 demands a thicker image plate for obtaining comparable neutron absorption. The greater thickness of the NIP inevitably leads to a loss in spatial resolution of the image plate. However, this reduction in resolution can be restricted by a novel image plate concept in which a ceramic structure with square cells (referred to as a 'honeycomb') is embedded in the NIP, resulting in a pixelated image plate. In such a NIP the read-out light is confined to the particular illuminated pixel, decoupling the spatial resolution from the optical properties of the image plate material and morphology. In this work, a comparison of experimentally determined and simulated spatial resolutions of pixelated and unstructured image plates for a fixed read-out laser intensity is presented, as well as simulations of the properties of these NIPs at higher laser powers.

  19. Modelling avalanche danger and understanding snow depth variability

    OpenAIRE

    2010-01-01

    This thesis addresses the causes of avalanche danger at a regional scale. Modelled snow stratigraphy variables were linked to [1] forecasted avalanche danger and [2] observed snowpack stability. Spatial variability of snowpack parameters in a region is an additional important factor that influences the avalanche danger. Snow depth and its change during individual snow fall periods are snowpack parameters which can be measured at a high spatial resolution. Hence, the spatial distribution of sn...

  20. Determining avalanche modelling input parameters using terrestrial laser scanning technology

    OpenAIRE

    2013-01-01

    International audience; In dynamic avalanche modelling, data about the volumes and areas of the snow released, mobilized and deposited are key input parameters, as well as the fracture height. The fracture height can sometimes be measured in the field, but it is often difficult to access the starting zone due to difficult or dangerous terrain and avalanche hazards. More complex is determining the areas and volumes of snow involved in an avalanche. Such calculations require high-resolution spa...

  1. New advances for modelling the debris avalanches

    Science.gov (United States)

    Cuomo, Sabatino; Cascini, Leonardo; Pastor, Manuel; Castorino, Giuseppe Claudio

    2013-04-01

    Flow-like landslides are a major global hazard and they occur worldwide causing a large number of casualties, significant structural damages to property and infrastructures as well as economic losses. When involving open slopes, these landslides often occur in triangular source areas where initial slides turn into avalanches through further failures and/or eventual soil entrainment. This paper deals with the numerical modelling of the propagation stage of debris avalanches which provides information such as the propagation pattern of the mobilized material, its velocity, thickness and run-out distance. In the paper, a "depth integrated" model is used which allows: i) adequately taking into account the irregular topography of real slopes which greatly affect the propagation stage and ii) using a less time consuming model than fully 3D approaches. The used model is named "GeoFlow_SPH" and it was formerly applied to theoretical, experimental and real case histories (Pastor et al., 2009; Cascini et al., 2012). In this work the behavior of debris avalanches is analyzed with special emphasis on the apical angle, one of the main features of this type of landslide, in relation to soil rheology, hillslope geometry and features of triggering area. Furthermore, the role of erosion has been investigated with reference to the uppermost parts of open slopes with a different steepness. These analyses are firstly carried out for simplified benchmark slopes, using both water-like materials (with no shear strength) and debris type materials. Then, three important case studies of Campania region (Cervinara, Nocera Inferiore e Sarno) are analyzed where debris avalanches involved pyroclastic soils originated from the eruptive products of Vesusius volcano. The results achieved for both benchmark slopes and real case histories outline the key role played by the erosion on the whole propagation stage of debris avalanches. The results are particularly satisfactory since they indicate the

  2. Correcting for accidental correlations in saturated avalanche photodiodes

    National Research Council Canada - National Science Library

    Grieve, J A; Chandrasekara, R; Tang, Z; Cheng, C; Ling, A

    2016-01-01

    .... As an example, we provide a detailed high-level model for the behaviour of passively quenched avalanche photodiodes, and demonstrate effective background subtraction at rates commonly associated...

  3. B-factory detectors

    CERN Document Server

    Marlow, D R

    2002-01-01

    The designs of the recently commissioned BaBar and Belle B-Factory detectors are described. The discussion is organized around the methods and instruments used to detect the so-called gold-plated-mode B sup 0->J/PSI K sub S decays and related modes.

  4. Readout of a LaCl sub 3 (Ce sup 3 sup +) scintillation crystal with a large area avalanche photodiode

    CERN Document Server

    Allier, C P; Dorenbos, P; Hollander, R W; Eijk, C W E; Kraemer, K W; Güdel, H U

    2002-01-01

    A high-resolution gamma-ray detector consisting of an 8 mm diameter and 5 mm thick LaCl sub 3 (Ce sup 3 sup +) scintillation crystal coupled to a 16 mm diameter APD from Advanced Photonix Inc is presented. The energy resolution R obtained at 662 keV is about 3.7% (full-width at half maximum). The low intrinsic resolution of about 2%, the high light yield of the crystal (46 000+-5000 photons per MeV) and the high quantum efficiency of the avalanche photodiode make this gamma-ray detector an excellent choice for applications were a high energy resolution is required.

  5. Room temperature single-photon detectors for high bit rate quantum key distribution

    Energy Technology Data Exchange (ETDEWEB)

    Comandar, L. C.; Patel, K. A. [Toshiba Research Europe Ltd., 208 Cambridge Science Park, Milton Road, Cambridge CB4 0GZ (United Kingdom); Engineering Department, Cambridge University, 9 J J Thomson Ave., Cambridge CB3 0FA (United Kingdom); Fröhlich, B., E-mail: bernd.frohlich@crl.toshiba.co.uk; Lucamarini, M.; Sharpe, A. W.; Dynes, J. F.; Yuan, Z. L.; Shields, A. J. [Toshiba Research Europe Ltd., 208 Cambridge Science Park, Milton Road, Cambridge CB4 0GZ (United Kingdom); Penty, R. V. [Engineering Department, Cambridge University, 9 J J Thomson Ave., Cambridge CB3 0FA (United Kingdom)

    2014-01-13

    We report room temperature operation of telecom wavelength single-photon detectors for high bit rate quantum key distribution (QKD). Room temperature operation is achieved using InGaAs avalanche photodiodes integrated with electronics based on the self-differencing technique that increases avalanche discrimination sensitivity. Despite using room temperature detectors, we demonstrate QKD with record secure bit rates over a range of fiber lengths (e.g., 1.26 Mbit/s over 50 km). Furthermore, our results indicate that operating the detectors at room temperature increases the secure bit rate for short distances.

  6. Advances in InGaAs/InP single-photon detector systems for quantum communication

    CERN Document Server

    Zhang, Jun; Zbinden, Hugo; Pan, Jian-Wei

    2015-01-01

    Single-photon detectors (SPDs) are the most sensitive instruments for light detection. In the near-infrared range, SPDs based on III-V compound semiconductor avalanche photodiodes have been extensively used during the past two decades for diverse applications due to their advantages in practicality including small size, low cost and easy operation. In the past decade, the rapid developments and increasing demands in quantum information science have served as key drivers to improve the device performance of single-photon avalanche diodes and to invent new avalanche quenching techniques. This Review aims to introduce the technology advances of InGaAs/InP single-photon detector systems in the telecom wavelengths and the relevant quantum communication applications, and particularly to highlight recent emerging techniques such as high-frequency gating at GHz rates and free-running operation using negative-feedback avalanche diodes. Future perspectives of both the devices and quenching techniques are summarized.

  7. Avalanche photodiode photon counting receivers for space-borne lidars

    Science.gov (United States)

    Sun, Xiaoli; Davidson, Frederic M.

    1991-01-01

    Avalanche photodiodes (APD) are studied for uses as photon counting detectors in spaceborne lidars. Non-breakdown APD photon counters, in which the APD's are biased below the breakdown point, are shown to outperform: (1) conventional APD photon counters biased above the breakdown point; (2) conventional APD photon counters biased above the breakdown point; and (3) APD's in analog mode when the received optical signal is extremely weak. Non-breakdown APD photon counters were shown experimentally to achieve an effective photon counting quantum efficiency of 5.0 percent at lambda = 820 nm with a dead time of 15 ns and a dark count rate of 7000/s which agreed with the theoretically predicted values. The interarrival times of the counts followed an exponential distribution and the counting statistics appeared to follow a Poisson distribution with no after pulsing. It is predicted that the effective photon counting quantum efficiency can be improved to 18.7 percent at lambda = 820 nm and 1.46 percent at lambda = 1060 nm with a dead time of a few nanoseconds by using more advanced commercially available electronic components.

  8. Interaction of Avalanche Photodiodes (APDs Devices With Thermal Irradiation Environments

    Directory of Open Access Journals (Sweden)

    Ahmed Nabih Zaki Rashed

    2012-04-01

    Full Text Available This paper has been examined the high temperature irradiation variations testing in order to be used to determine avalanche photodiode lifetime, even though APD failure mechanisms are more sensitive to increases in current density. As a measured parameter of degradation, the current density is of great significance when searching for failure modes in APD. Raising the current density however, is not really indicative of lifetime since it is more likely a situation to be avoided than one that simulates normal lifetime degradation. The reliability of semiconductor detectors is very dependent on the degradation modes. This paper has investigated deeply some of the degradation performance and capabilities of typical APDs currently used in many communication and sensing systems over wide range of the affecting parameters. APDs are used in systems that require coherent and often single mode light such as high data rate communications and sensing applications. APDs are an attractive receiver choice for photon-starved (low signal applications, because their internal gain mechanism can improve signal to noise ratio. An optical receiver must also be appropriate for the laser wavelength being used. The near infrared is the preferred wavelength regime for deep space optical communications largely due to the wavelengths of available laser technologies that meet the optical power requirements of a deep space optical link

  9. Direction sensitive neutron detector

    Energy Technology Data Exchange (ETDEWEB)

    Ahlen, Steven; Fisher, Peter; Dujmic, Denis; Wellenstein, Hermann F.; Inglis, Andrew

    2017-01-31

    A neutron detector includes a pressure vessel, an electrically conductive field cage assembly within the pressure vessel and an imaging subsystem. A pressurized gas mixture of CF.sub.4, .sup.3He and .sup.4He at respective partial pressures is used. The field cage establishes a relatively large drift region of low field strength, in which ionization electrons generated by neutron-He interactions are directed toward a substantially smaller amplification region of substantially higher field strength in which the ionization electrons undergo avalanche multiplication resulting in scintillation of the CF.sub.4 along scintillation tracks. The imaging system generates two-dimensional images of the scintillation patterns and employs track-finding to identify tracks and deduce the rate and direction of incident neutrons. One or more photo-multiplier tubes record the time-profile of the scintillation tracks permitting the determination of the third coordinate.

  10. Subnanosecond Scintillation Detector

    Science.gov (United States)

    Hoenk, Michael (Inventor); Hennessy, John (Inventor); Hitlin, David (Inventor)

    2017-01-01

    A scintillation detector, including a scintillator that emits scintillation; a semiconductor photodetector having a surface area for receiving the scintillation, wherein the surface area has a passivation layer configured to provide a peak quantum efficiency greater than 40% for a first component of the scintillation, and the semiconductor photodetector has built in gain through avalanche multiplication; a coating on the surface area, wherein the coating acts as a bandpass filter that transmits light within a range of wavelengths corresponding to the first component of the scintillation and suppresses transmission of light with wavelengths outside said range of wavelengths; and wherein the surface area, the passivation layer, and the coating are controlled to increase the temporal resolution of the semiconductor photodetector.

  11. Controlling an actively-quenched single photon detector with bright light.

    Science.gov (United States)

    Sauge, Sebastien; Lydersen, Lars; Anisimov, Andrey; Skaar, Johannes; Makarov, Vadim

    2011-11-01

    We control using bright light an actively-quenched avalanche single-photon detector. Actively-quenched detectors are commonly used for quantum key distribution (QKD) in the visible and near-infrared range. This study shows that these detectors are controllable by the same attack used to hack passively-quenched and gated detectors. This demonstrates the generality of our attack and its possible applicability to eavsdropping the full secret key of all QKD systems using avalanche photodiodes (APDs). Moreover, the commercial detector model we tested (PerkinElmer SPCM-AQR) exhibits two new blinding mechanisms in addition to the previously observed thermal blinding of the APD, namely: malfunctioning of the bias voltage control circuit, and overload of the DC/DC converter biasing the APD. These two new technical loopholes found just in one detector model suggest that this problem must be solved in general, by incorporating generally imperfect detectors into the security proof for QKD.

  12. The analysis of the integral gated mode single photon detector

    Institute of Scientific and Technical Information of China (English)

    Wei Zheng-Jun; Li Kai-Zhen; Zhou Peng; Wang Jin-Dong; Liao Chang-Jun; Guo Jian-Ping; Liang Rui-Sheng; Liu Song-Hao

    2008-01-01

    This paper critically analyses and simulates the circuit configuration of the integral gated mode single photon detector which is proposed for eliminating the transient spikes problem of conventional gated mode single photon detector.The relationship between the values of the circuit elements and the effect of transient spikes cancellation has been obtained.With particular emphasis,the bias voltage of the avalanche photodiode and the output signal voltage of the integrator have been calculated.The obtained analysis results indicate that the output signal voltage of the integrator only relates to the total quantity of electricity of the avalanche charges by choosing the correct values of the circuit elements and integral time interval.These results can be used to optimize the performance of single photon detectors and provide guides for the design of single photon detectors.

  13. Signal and noise properties of position-sensitive avalanche photodiodes.

    Science.gov (United States)

    Yang, Yongfeng; Wu, Yibao; Farrell, Richard; Dokhale, Purushottam A; Shah, Kanai S; Cherry, Simon R

    2011-10-07

    After many years of development, position-sensitive avalanche photodiodes (PSAPDs) are now being incorporated into a range of scintillation detector systems, including those used in high-resolution small-animal PET and PET/MR scanners. In this work, the signal, noise, signal-to-noise ratio (SNR), flood histogram and timing resolution were measured for lutetium oxyorthosilicate (LSO) scintillator arrays coupled to PSAPDs ranging in size from 10 to 20 mm, and the optimum bias voltage and working temperature were determined. Variations in the SNR performance of PSAPDs with the same dimensions were small, but the SNR decreased significantly with increasing PSAPD size and increasing temperature. Smaller PSAPDs (10 mm and 15 mm in width) produced acceptable flood histograms at 24 °C, and cooling lower than 16 °C produced little improvement. The optimum bias voltage was about 25 V below the break down voltage. The larger 20 mm PSAPDs have lower SNR and require cooling to 0-7 °C for acceptable performance. The optimum bias voltage is also lower (35 V or more below the break down voltage depending on the temperature). Significant changes in the timing resolution were observed as the bias voltage and temperature varied. Higher bias voltages provided better timing resolution. The best timing resolution obtained for individual crystals was 2.8 ns and 3.3 ns for the 10 mm and 15 mm PSAPDs, respectively. The results of this work provide useful guidance for selecting the bias voltage and working temperature for scintillation detectors that incorporate PSAPDs as the photodetector.

  14. Photosensitive Gaseous Detectors for Cryogenic Temperature Applications

    CERN Document Server

    Periale, L; Iacobaeus, C; Lund-Jensen, B; Picchi, P; Pietropaolo, F

    2007-01-01

    There are several proposals and projects today for building LXe Time Projection Chambers (TPCs) for dark matter search. An important element of these TPCs are the photomultipliers operating either inside LXe or in vapors above the liquid. We have recently demonstrated that photosensitive gaseous detectors (wire type and hole-type) can operate perfectly well until temperatures of LN2. In this paper results of systematic studies of operation of the photosensitive version of these detectors (combined with reflective or semi-transparent CsI photocathodes) in the temperature interval of 300-150 K are presented. In particular, it was demonstrated that both sealed and flushed by a gas detectors could operate at a quite stable fashion in a year/time scale. Obtained results, in particular the long-term stability of photosensitive gaseous detectors, strongly indicate that they can be cheap and simple alternatives to photomultipliers or avalanche solid-state detectors in LXe TPC applications.

  15. Characterization of large area APDs for the EXO-200 detector

    CERN Document Server

    Neilson, R; Pocar, A; Kumar, K; Odian, A; Prescott, C Y; Tenev, V; Ackerman, N; Akimov, D; Auger, M; Benitez-Medina, C; Breidenbach, M; Burenkov, A; Conley, R; Cook, S; deVoe, R; Dolinski, M J; Fairbank, W; Farine, J; Fierlinger, P; Flatt, B; Gornea, R; Gratta, G; Green, M; Hall, C; Hall, K; Hallman, D; Hargrove, C; Herrin, S; Hodgson, J; Kaufman, L J; Kovalenko, A; Leonard, D S; Mackay, D; Mong, B; Diez, M Montero; Niner, E; O'Sullivan, K; Piepke, A; Rowson, P C; Sinclair, D; Skarpaas, K; Slutsky, S; Stekhanov, V; Strickland, V; Twelker, K; Vuilleumier, J -L; Wamba, K; Wichoski, U; Wodin, J; Yang, L; Yen, Y -R

    2009-01-01

    EXO-200 uses 468 large area avalanche photodiodes (LAAPDs) for detection of scintillation light in an ultra-low-background liquid xenon (LXe) detector. We describe initial measurements of dark noise, gain and response to xenon scintillation light of LAAPDs at temperatures from room temperature to 169K - the temperature of liquid xenon. We also describe the individual characterization of more than 800 LAAPDs for selective installation in the EXO-200 detector.

  16. Characterization of Large Area APDs for the EXO-200 Detector

    Energy Technology Data Exchange (ETDEWEB)

    Neilson, R.; LePort, F.; Pocar, A.; /Stanford U., Phys. Dept.; Kumar, K.; /Massachusetts U., Amherst; Odian, A.; Prescott, C.Y.; /SLAC; Tenev, V.; /Stanford U., Phys. Dept.; Ackerman, N.; /SLAC; Akimov, D.; /Moscow, ITEP; Auger, M.; /Bern U., LHEP; Benitez-Medina, C.; /Colorado State U.; Breidenbach, M.; /SLAC; Burenkov, A.; /Moscow, ITEP; Conley, R.; /SLAC; Cook, S.; /Colorado State U.; deVoe, R.; Dolinski, M.J.; /Stanford U., Phys. Dept.; Fairbank, W., Jr.; /Colorado State U.; Farine, J.; /Laurentian U.; Fierlinger, P.; Flatt, B.; /Stanford U., Phys. Dept. /Bern U., LHEP /Stanford U., Phys. Dept. /Maryland U. /Colorado State U. /Laurentian U. /Carleton U. /SLAC /Maryland U. /Moscow, ITEP /Alabama U. /SLAC /Colorado State U. /Stanford U., Phys. Dept. /Alabama U. /Stanford U., Phys. Dept. /Alabama U. /SLAC /Carleton U. /SLAC /Maryland U. /Moscow, ITEP /Carleton U. /Stanford U., Phys. Dept. /Bern U., LHEP /SLAC /Laurentian U. /SLAC /Maryland U.

    2011-12-02

    EXO-200 uses 468 large area avalanche photodiodes (LAAPDs) for detection of scintillation light in an ultra-low-background liquid xenon (LXe) detector. We describe initial measurements of dark noise, gain and response to xenon scintillation light of LAAPDs at temperatures from room temperature to 169 K - the temperature of liquid xenon. We also describe the individual characterization of more than 800 LAAPDs for selective installation in the EXO-200 detector.

  17. Design optimization of ultra-fast silicon detectors

    Energy Technology Data Exchange (ETDEWEB)

    Cartiglia, N., E-mail: cartiglia@to.infn.it [INFN Torino (Italy); Arcidiacono, R. [Università del Piemonte Orientale, Novara (Italy); Baselga, M. [Centro Nacional de Microeletronica, IMB-CNM, Barcelona (Spain); Bellan, R. [Università di Torino, Torino (Italy); Boscardin, M. [Fondazione Bruno Kessler, Via Sommarive 18, 38123 Trento (Italy); Cenna, F. [INFN Torino (Italy); Dalla Betta, G.F. [Università di Trento, Via Sommarive 9, 38123 Trento (Italy); Fernndez-Martnez, P. [Centro Nacional de Microeletronica, IMB-CNM, Barcelona (Spain); Ferrero, M. [INFN Torino (Italy); Università di Torino, Torino (Italy); Flores, D. [Centro Nacional de Microeletronica, IMB-CNM, Barcelona (Spain); Galloway, Z. [Santa Cruz Institute for Particle Physics UC Santa Cruz, CA 95064 (United States); Greco, V.; Hidalgo, S. [Centro Nacional de Microeletronica, IMB-CNM, Barcelona (Spain); Marchetto, F. [INFN Torino (Italy); Monaco, V. [Università di Torino, Torino (Italy); Obertino, M. [Università del Piemonte Orientale, Novara (Italy); Pancheri, L. [Università di Trento, Via Sommarive 9, 38123 Trento (Italy); Paternoster, G. [Fondazione Bruno Kessler, Via Sommarive 18, 38123 Trento (Italy); Picerno, A. [Università di Torino, Torino (Italy); Pellegrini, G. [Centro Nacional de Microeletronica, IMB-CNM, Barcelona (Spain); and others

    2015-10-01

    Low-Gain Avalanche Diodes (LGAD) are silicon detectors with output signals that are about a factor of 10 larger than those of traditional sensors. In this paper we analyze how the design of LGAD can be optimized to exploit their increased output signal to reach optimum timing performances. Our simulations show that these sensors, the so-called Ultra-Fast Silicon Detectors (UFSD), will be able to reach a time resolution factor of 10 better than that of traditional silicon sensors.

  18. Avalanches in UGe{sub 2}

    Energy Technology Data Exchange (ETDEWEB)

    Lhotel, E. E-mail: lhotel@grenoble.cnrs.fr; Paulsen, C.; Huxley, A.D

    2004-05-01

    In UGe{sub 2} ferromagnetism and superconductivity co-exist for pressures in the range 1.0-1.6 GPa. The magnetic state, however, has several unusual properties. Here we report measurements of hysteresis loops for fields parallel to the easy-axis at low temperature and ambient pressure, measured for two separate UGe{sub 2} single crystals. Steps in the magnetization as the field is changed at low temperature are observed for both crystals. The general phenomenology associated with the steps strongly suggests that they correspond to avalanches of domain-wall motion.

  19. Avalanche Effect in Improperly Initialized CAESAR Candidates

    Directory of Open Access Journals (Sweden)

    Martin Ukrop

    2016-12-01

    Full Text Available Cryptoprimitives rely on thorough theoretical background, but often lack basic usability features making them prone to unintentional misuse by developers. We argue that this is true even for the state-of-the-art designs. Analyzing 52 candidates of the current CAESAR competition has shown none of them have an avalanche effect in authentication tag strong enough to work properly when partially misconfigured. Although not directly decreasing their security profile, this hints at their security usability being less than perfect. Paper details available at crcs.cz/papers/memics2016

  20. Bilayer avalanche spin-diode logic

    Energy Technology Data Exchange (ETDEWEB)

    Friedman, Joseph S., E-mail: joseph.friedman@u-psud.fr; Querlioz, Damien [Institut d’Electronique Fondamentale, Univ. Paris-Sud, CNRS, 91405 Orsay (France); Fadel, Eric R. [Department of Materials Science, Massachusetts Institute of Technology, Cambridge, MA 02139 (United States); Wessels, Bruce W. [Department of Electrical Engineering & Computer Science, Northwestern University, Evanston, IL 60208 (United States); Department of Materials Science & Engineering, Northwestern University, Evanston, IL 60208 (United States); Sahakian, Alan V. [Department of Electrical Engineering & Computer Science, Northwestern University, Evanston, IL 60208 (United States); Department of Biomedical Engineering, Northwestern University, Evanston, IL 60208 (United States)

    2015-11-15

    A novel spintronic computing paradigm is proposed and analyzed in which InSb p-n bilayer avalanche spin-diodes are cascaded to efficiently perform complex logic operations. This spin-diode logic family uses control wires to generate magnetic fields that modulate the resistance of the spin-diodes, and currents through these devices control the resistance of cascaded devices. Electromagnetic simulations are performed to demonstrate the cascading mechanism, and guidelines are provided for the development of this innovative computing technology. This cascading scheme permits compact logic circuits with switching speeds determined by electromagnetic wave propagation rather than electron motion, enabling high-performance spintronic computing.

  1. Radiation and Temperature Hard Multi-Pixel Avalanche Photodiodes

    Science.gov (United States)

    Bensaoula, Abdelhak (Inventor); Starikov, David (Inventor); Pillai, Rajeev (Inventor)

    2017-01-01

    The structure and method of fabricating a radiation and temperature hard avalanche photodiode with integrated radiation and temperature hard readout circuit, comprising a substrate, an avalanche region, an absorption region, and a plurality of Ohmic contacts are presented. The present disclosure provides for tuning of spectral sensitivity and high device efficiency, resulting in photon counting capability with decreased crosstalk and reduced dark current.

  2. Validation of DEM prediction for granular avalanches on irregular terrain

    Science.gov (United States)

    Mead, Stuart R.; Cleary, Paul W.

    2015-09-01

    Accurate numerical simulation can provide crucial information useful for a greater understanding of destructive granular mass movements such as rock avalanches, landslides, and pyroclastic flows. It enables more informed and relatively low cost investigation of significant risk factors, mitigation strategy effectiveness, and sensitivity to initial conditions, material, or soil properties. In this paper, a granular avalanche experiment from the literature is reanalyzed and used as a basis to assess the accuracy of discrete element method (DEM) predictions of avalanche flow. Discrete granular approaches such as DEM simulate the motion and collisions of individual particles and are useful for identifying and investigating the controlling processes within an avalanche. Using a superquadric shape representation, DEM simulations were found to accurately reproduce transient and static features of the avalanche. The effect of material properties on the shape of the avalanche deposit was investigated. The simulated avalanche deposits were found to be sensitive to particle shape and friction, with the particle shape causing the sensitivity to friction to vary. The importance of particle shape, coupled with effect on the sensitivity to friction, highlights the importance of quantifying and including particle shape effects in numerical modeling of granular avalanches.

  3. Avalanche Statistics of Driven Granular Slides in a Miniature Mound

    CERN Document Server

    Juanico, D E; Batac, R; Monterola, C

    2008-01-01

    We examine avalanche statistics of rain- and vibration-driven granular slides in miniature soil mounds using experimental and numerical approaches. A crossover from power-law to non power-law avalanche-size statistics is demonstrated as a generic driving rate $\

  4. Avalanches mediate crystallization in a hard-sphere glass.

    Science.gov (United States)

    Sanz, Eduardo; Valeriani, Chantal; Zaccarelli, Emanuela; Poon, Wilson C K; Cates, Michael E; Pusey, Peter N

    2014-01-07

    By molecular-dynamics simulations, we have studied the devitrification (or crystallization) of aged hard-sphere glasses. First, we find that the dynamics of the particles are intermittent: Quiescent periods, when the particles simply "rattle" in their nearest-neighbor cages, are interrupted by abrupt "avalanches," where a subset of particles undergo large rearrangements. Second, we find that crystallization is associated with these avalanches but that the connection is not straightforward. The amount of crystal in the system increases during an avalanche, but most of the particles that become crystalline are different from those involved in the avalanche. Third, the occurrence of the avalanches is a largely stochastic process. Randomizing the velocities of the particles at any time during the simulation leads to a different subsequent series of avalanches. The spatial distribution of avalanching particles appears random, although correlations are found among avalanche initiation events. By contrast, we find that crystallization tends to take place in regions that already show incipient local order.

  5. Reducing the Spikes of Avalanche Photodiode Measurements at the National Spherical Torus Experiment

    Science.gov (United States)

    Brubaker, Z. E.; Foley, E. L.

    2011-10-01

    Avalanche Photodiodes (APD) used at the National Spherical Torus Experiment (NSTX) make important measurements for the Motional Stark Effect (MSE) diagnostic. However, they are very sensitive, and if radiation consistently reaches these detectors they are damaged over time. Furthermore, they also display spikes in their readings, which greatly complicates the data analysis for MSE. Due to our Collisionally-Induced Fluorescence Motional Stark Effect diagnostic observing significant radiation despite being shielded by a 3 foot concrete wall, we must devise a plan for shielding our new Laser-Induced Fluorescence Motional Stark Effect diagnostic, as well as determining the best possible location for them. In order to reduce the amount of spikes seen in our readings and to preserve our detectors, I investigated the type of radiation responsible, the locations most affected, and tested various materials for shielding. Results will be presented.

  6. Application of PN and avalanche silicon photodiodes to low-level optical

    Science.gov (United States)

    Eppeldauer, G.; Schaefer, A. R.

    1988-01-01

    New approaches to the discovery of other planetary systems require very sensitive and stable detection techniques in order to succeed. Two methods in particular, the astrometric and the photometric methods, require this. To begin understanding the problems and limitations of solid state detectors regarding this application, preliminary experiments were performed at the National Bureau of Standards and a low light level detector characterization facility was built. This facility is briefly described, and the results of tests conducted in it are outlined. A breadboard photometer that was used to obtain stellar brightness ratio precision data is described. The design principles of PN and avalanche silicon photodiodes based on low light level measuring circuits are discussed.

  7. Performance Analysis of Single Photon Avalanche Diode Underwater VLC System Using ARQ

    KAUST Repository

    Shafiqu, Taniya

    2017-08-24

    Single photon avalanche diode (SPAD) has recently been introduced as a powerful detector for long distance underwater visible light (UVLC) communication. In this paper, the performance of the SPAD detector in UVLC is analyzed considering the effect of the turbulence induced fading resulting from air bubbles in addition to the combined effect of attenuation and scattering. Automatic repeat request (ARQ) system is adopted to mitigate different underwater impairments and reduce the error probability at the receiver side. Approximate packet error rate (PER) expressions are derived using Laguerre Gauss polynomial for a finite number of transmission. Next, the average energy efficiency and throughput are analyzed to account for the increased energy consumption cost and the decreased effective transmission rate, which results from adopting the ARQ scheme. Finally, different numerical results are introduced to verify the derived PER expressions, demonstrate the ability of the proposed ARQ system in extending the transmission range, and show the trade-off between energy efficiency (EE) and throughput.

  8. Hybrid AlGaN-SiC Avalanche Photodiode for Deep-UV Photon Detection

    Science.gov (United States)

    Aslam, Shahid; Herrero, Federico A.; Sigwarth, John; Goldsman, Neil; Akturk, Akin

    2010-01-01

    The proposed device is capable of counting ultraviolet (UV) photons, is compatible for inclusion into space instruments, and has applications as deep- UV detectors for calibration systems, curing systems, and crack detection. The device is based on a Separate Absorption and Charge Multiplication (SACM) structure. It is based on aluminum gallium nitride (AlGaN) absorber on a silicon carbide APD (avalanche photodiode). The AlGaN layer absorbs incident UV photons and injects photogenerated carriers into an underlying SiC APD that is operated in Geiger mode and provides current multiplication via avalanche breakdown. The solid-state detector is capable of sensing 100-to-365-nanometer wavelength radiation at a flux level as low as 6 photons/pixel/s. Advantages include, visible-light blindness, operation in harsh environments (e.g., high temperatures), deep-UV detection response, high gain, and Geiger mode operation at low voltage. Furthermore, the device can also be designed in array formats, e.g., linear arrays or 2D arrays (micropixels inside a superpixel).

  9. Nanoscale avalanche photodiodes for highly sensitive and spatially resolved photon detection.

    Science.gov (United States)

    Hayden, Oliver; Agarwal, Ritesh; Lieber, Charles M

    2006-05-01

    Integrating nanophotonics with electronics could enhance and/or enable opportunities in areas ranging from communications and computing to novel diagnostics. Light sources and detectors are important elements for integration, and key progress has been made using semiconducting nanowires and carbon nanotubes to yield electrically driven sources and photoconductor detectors. Detection with photoconductors has relatively poor sensitivity at the nanometre scale, and thus large amplification is required to detect low light levels and ultimately single photons with reasonable response time. Here, we report avalanche multiplication of the photocurrent in nanoscale p-n diodes consisting of crossed silicon-cadmium sulphide nanowires. Electrical transport and optical measurements demonstrate that the nanowire avalanche photodiodes (nanoAPDs) have ultrahigh sensitivity with detection limits of less than 100 photons, and subwavelength spatial resolution of at least 250 nm. Crossed nanowire arrays also show that nanoAPDs are reproducible and can be addressed independently without cross-talk. NanoAPDs and arrays could open new opportunities for ultradense integrated systems, sensing and imaging applications.

  10. First prototypes of two-tier avalanche pixel sensors for particle detection

    Science.gov (United States)

    Pancheri, L.; Brogi, P.; Collazuol, G.; Dalla Betta, G.-F.; Ficorella, A.; Marrocchesi, P. S.; Morsani, F.; Ratti, L.; Savoy-Navarro, A.

    2017-02-01

    In this paper, we present the implementation and preliminary evaluation of a new type of silicon sensor for charged particle detection operated in Geiger-mode. The proposed device, formed by two vertically-aligned pixel arrays, exploits the coincidence between two simultaneous avalanche events to discriminate between particle-triggered detections and dark counts. A proof-of-concept two-layer sensor with per-pixel coincidence circuits was designed and fabricated in a 150 nm CMOS process and vertically integrated through bump bonding. The sensor includes a 48×16 pixel array with 50 μ m × 75 μ m pixels. This work describes the sensor architecture and reports a selection of results from the characterization of the avalanche detectors in the two layers. Detectors with an active area of 43 × 45 μ m2 have a median dark count rate of 3 kHz at 3.3 V excess bias and a breakdown voltage non-uniformity lower than 20 mV.

  11. Avalanche behavior of power MOSFETs under different temperature conditions

    Institute of Scientific and Technical Information of China (English)

    Lu Jiang; Wang Lixin; Lu Shuojin; Wang Xuesheng; Han Zhengsheng

    2011-01-01

    The ability of high-voltage power MOSFETs to withstand avalanche events under different temperature conditions are studied by experiment and two-dimensional device simulation. The experiment is performed to investigate dynamic avalanche failure behavior of the domestic power MOSFETs which can occur at the rated maximum operation temperature range (-55 to 150 ℃). An advanced ISE TCAD two-dimensional mixed mode simulator with thermodynamic non-isothermal model is used to analyze the avalanche failure mechanism. The unclamped inductive switching measurement and simulation results show that the parasitic components and thermal effect inside the device will lead to the deterioration of the avalanche reliability of power MOSFETs with increasing temperature. The main failure mechanism is related to the parasitic bipolar transistor activity during the occurrence of the avalanche behavior.

  12. Resonant nuclear scattering of synchrotron radiation: Detector development and specular scattering from a thin layer of {sup 57}Fe

    Energy Technology Data Exchange (ETDEWEB)

    Baron, A.Q.R.

    1995-04-01

    This thesis explores resonant nudear scattering of synchrotron radiation. An introductory chapter describes some useful concepts, such as speedup and coherent enhancement, in the context of some basic physical principles. Methods of producing highly monochromatic synchrotron beams usmg either electronic or nuclear scattering are also discussed. The body of the thesis concentrates on detector development and specular scattering from iynthetic layered materials. A detector employing n-dcrochannel plate electron multipliers is shown to have good ({approximately}50%) effidency for detecting 14.4 key x-rays incident at small ({approximately}0.5 degree) grazing angles onto Au or CsI photocathodes. However, being complicated to use, it was replaced with a large area (>=lan2) avalanche photodiode (APD) detector. The APD`s are simpler to use and have comparable (30--70%) efficiencies at 14.4 key, subnanosecond time resolution, large dynan-dc range (usable at rates up to {approximately}10{sup 8} photons/second) and low (<{approximately}0.01 cts/sec) background rates. Maxwell`s equations are used to derive the specular x-ray reflectivity of layered materials with resonant transitions and complex polarization dependencies. The effects of interfadal roughness are treated with some care, and the distorted wave Born approximation (DWBA) used to describe electronic scattering is generalized to the nuclear case. The implications of the theory are discussed in the context of grazing incidence measurements with emphasis on the kinematic and dynamical aspects of the scattering.

  13. A new fission-fragment detector to complement the CACTUS-SiRi setup at the Oslo Cyclotron Laboratory

    CERN Document Server

    Tornyi, Tamás Gábor; Guttormsen, Magne; Larsen, Ann-Cecilie; Siem, Sunniva; Krasznahorkay, Attila; Csige, Lóránt

    2013-01-01

    An array of Parallel Plate Avalanche Counters (PPAC) for the detection of heavy ions has been developed. The new device, NIFF (Nuclear Instrument for Fission Fragments), consists of four individual detectors and covers $60\\%$ of 2$\\pi$. It was designed to be used in conjunction with the SiRi array of ${\\Delta}E-E$ silicon telescopes for light charged particles and fits into the CACTUS array of 28 large-volume NaI scintillation detectors at the Oslo Cyclotron Laboratory. The low-pressure gas-filled PPACs are sensitive for the detection of fission fragments, but are insensitive to scattered beam particles of light ions or light-ion ejectiles. The PPAC detectors of NIFF have good time resolution and can be used either to select or to veto fission events in in-beam experiments with light-ion beams and actinide targets. The powerful combination of SiRi, CACTUS, and NIFF provides new research opportunities for the study of nuclear structure and nuclear reactions in the actinide region. The new setup is particularly...

  14. A new fission-fragment detector to complement the CACTUS-SiRi setup at the Oslo Cyclotron Laboratory

    Science.gov (United States)

    Tornyi, T. G.; Görgen, A.; Guttormsen, M.; Larsen, A. C.; Siem, S.; Krasznahorkay, A.; Csige, L.

    2014-02-01

    An array of Parallel Plate Avalanche Counters (PPAC) for the detection of heavy ions has been developed. The new device, NIFF (Nuclear Instrument for Fission Fragments), consists of four individual detectors and covers 60% of 2π. It was designed to be used in conjunction with the SiRi array of ΔE-E silicon telescopes for light charged particles and fits into the CACTUS array of 28 large-volume NaI scintillation detectors at the Oslo Cyclotron Laboratory. The low-pressure gas-filled PPACs are sensitive for the detection of fission fragments, but are insensitive to scattered beam particles of light ions or light-ion ejectiles. The PPAC detectors of NIFF have good time resolution and can be used either to select or to veto fission events in in-beam experiments with light-ion beams and actinide targets. The powerful combination of SiRi, CACTUS, and NIFF provides new research opportunities for the study of nuclear structure and nuclear reactions in the actinide region. The new setup is particularly well suited to study the competition of fission and γ decay as a function of excitation energy.

  15. Recent Sand Avalanching on Rabe Crater Dunes

    Science.gov (United States)

    2000-01-01

    Dark streaks on the steep, down-wind slopes of sand dunes in Rabe Crater are seen at several locations in this Mars Global Surveyor (MGS) Mars Orbiter Camera (MOC) image. These streaks indicate relatively recent (i.e., in the past few years or less) movement of sand down these slopes.Sand dunes move forward by the combined action of wind that drives sand up the shallow slope on the windward side of the dune (in this case, the slopes that face toward the lower right) and the avalanching of this sand down the steeper, lee-side slope. The steep slope is also known as the slip face. The dark streaks indicated by arrows are evidence for sand avalanches that occurred within a few months or years of the time when the picture was taken in March 1999. Other streaks which are seen criss-crossing the dunes may be the result of passing dust devils. This image is illuminated from the upper left and located in Rabe Crater of the Hellespontus-Noachis region near 44.2oS, 325.6oW.

  16. Calculation of the charge spectrum generated by ionizing particles in Resistive Plate Chambers at low gas gain

    CERN Document Server

    Fonte, P

    2012-01-01

    The charge spectrum generated by ionizing particles in Resistive Plate Chambers under Townsend avalanche conditions, that is, for sufficiently small avalanches not affected by space-charge, has not been calculated from first principles. In this article it is shown that, just neglecting cluster statistics, it follows closely the statistical gamma distribution. Remarkably, this distribution seems to describe as well data measured beyond these assumptions, rising some interpretation issues.

  17. The giant Ruatoria debris avalanche on the northern Hikurangi margin, New Zealand: Result of oblique seamount subduction

    Science.gov (United States)

    Collot, Jean-Yves; Lewis, Keith; Lamarche, Geoffroy; Lallemand, Serge

    2001-09-01

    Despite convergent margins being unstable systems, most reports of huge submarine slope failure have come from oceanic volcanoes and passive margins. Swath bathymetry and seismic profiles of the northern Hikurangi subduction system, New Zealand, show a tapering 65-30 km wide by 65 km deep margin indentation, with a giant, 3150±630 km3, blocky, debris avalanche deposit projecting 40 km out across horizontal trench fill, and a debris flow deposit projecting over 100 km. Slide blocks are well-bedded, up to 18 km across and 1.2 km high, the largest being at the avalanche deposit's leading edge. Samples dredged from them are mainly Miocene shelf calc-mudstones similar to those outcropping around the indentation. Cores from cover beds suggest that failure occurred ˜170±40 ka, possibly synchronously with a major extension collapse in the upper indentation. However, the northern part of the indentation is much older. The steep, straight northern wall is close to the direction of plate convergence and probably formed around 2.0-0.16 Ma as a large seamount subducted, leaving in its wake a deep groove obliquely across the margin and an unstable triangle of fractured rock in the 60° angle between groove and oversteepened margin front. The triangle collapsed as a blocky avalanche, leaving a scalloped southern wall and probably causing a large tsunami. Tentative calculations of compacted volumes suggest that the indentation is over 600 km3 larger than the avalanche, supporting a two-stage origin that includes subduction erosion. Since failure, convergence has carried the deposits ˜9 km back toward the margin, causing internal compression. The eventual subduction/accretion of the Ruatoria avalanche explains the scarcity of such features on active margins and perhaps the nature of olistostromes in fold belts.

  18. HgCdTe and silicon detectors and FPAs for remote sensing applications

    Science.gov (United States)

    D'Souza, Arvind I.; Stapelbroek, Maryn G.; Robinson, James E.

    2004-02-01

    Photon detectors and focal plane arrays (FPAs) are fabricated from HgCdTe and silicon in many varieties. With appropriate choices for bandgap in HgCdTe, detector architecture, dopants, and operating temperature, HgCdTe and silicon can cover the spectral range from ultraviolet to the very-long-wavelength infrared (VLWIR), exhibit high internal gain to allow photon counting over this broad spectral range, and can be made in large array formats for imaging. DRS makes HgCdTe and silicon detectors and FPAs with unique architectures for a variety of applications. Detector characteristics of High Density Vertically Integrated Photodiode (HDVIP) HdCdTe detectors as well as Focal Plane Arrays (FPAs) are presented in this paper. MWIR[λc(78 K) = 5 μm] HDVIP detectors RoA performance was measured to within a factor or two or three of theoretical. In addition, 256 x 256 detector arrays were fabricated. Initial measurements had seven out of ten FPAs having operabilities greater than 99.45% with the best 256 x 256 array having only two inoperable pixels. LWIR [λc(78K)~10 μm] 640 X 480 arrays and a variety of single color linear arrays have also been fabricated. In addition, two-color arrays have been fabricated. DRS has explored HgCdTe avalanche photo diodes (APDs) in the λc = 2.2 μm to 5 μm range. The λc = 5 μm APDs have greater than 200 DC gain values at 8 Volts bias. Large-format to 10242 Arsenic-doped (Si:As, λc ~ 28 μm), Blocked-Impurity-Band (BIB) detectors have been developed for a variety of pixel formats and have been optimized for low, moderate, and high infrared backgrounds. Antimony-doped silicon (Si:Sb) BIB arrays having response to wavelengths > 40 μm have also been demonstrated. Avalanche processes in Si:As at low temperatures (~ 8 K) have led to two unique solid-state photon-counting detectors adapted to infrared and visible wavelengths. The infrared device is the solid-state photomultiplier (SSPM). A related device optimized for the visible spectral

  19. Single Photon Detector at Telecom Wavelengths for Quantum Key Distribution

    Institute of Scientific and Technical Information of China (English)

    LIU Yun; WU Qing-Lin; HAN Zheng-Fu; DAI Yi-Min; QUO Guang-Can

    2006-01-01

    Using InGaAs/InP avalanche photodiodes as sensors and coaxial cables as reflection lines to reject spike signals, we have firstly employed the "timing filtering" gates to pick out avalanche signals and have realized the single photon detection at 1550 nm in the temperature range of thermoelectric cooling. A ratio of the dark count rate to the detection efficiency was obtained to be 9×10-5 at 223K. When the detector is applied to a practical quantum key distribution system, the transmission distance can reach 89.5km and the repetition rate can reach 0.33MHz.

  20. Single-Photon Avalanche Diodes (SPAD) in CMOS 0.35 µm technology

    Energy Technology Data Exchange (ETDEWEB)

    Pellion, D.; Jradi, K.; Brochard, N. [Le2i – CNRS/Univ. de Bourgogne, Dijon (France); Prêle, D. [APC – CNRS/Univ. Paris Diderot, Paris (France); Ginhac, D. [Le2i – CNRS/Univ. de Bourgogne, Dijon (France)

    2015-07-01

    Some decades ago single photon detection used to be the terrain of photomultiplier tube (PMT), thanks to its characteristics of sensitivity and speed. However, PMT has several disadvantages such as low quantum efficiency, overall dimensions, and cost, making them unsuitable for compact design of integrated systems. So, the past decade has seen a dramatic increase in interest in new integrated single-photon detectors called Single-Photon Avalanche Diodes (SPAD) or Geiger-mode APD. SPAD are working in avalanche mode above the breakdown level. When an incident photon is captured, a very fast avalanche is triggered, generating an easily detectable current pulse. This paper discusses SPAD detectors fabricated in a standard CMOS technology featuring both single-photon sensitivity, and excellent timing resolution, while guaranteeing a high integration. In this work, we investigate the design of SPAD detectors using the AMS 0.35 µm CMOS Opto technology. Indeed, such standard CMOS technology allows producing large surface (few mm{sup 2}) of single photon sensitive detectors. Moreover, SPAD in CMOS technologies could be associated to electronic readout such as active quenching, digital to analog converter, memories and any specific processing required to build efficient calorimeters (Silicon PhotoMultiplier – SiPM) or high resolution imagers (SPAD imager). The present work investigates SPAD geometry. MOS transistor has been used instead of resistor to adjust the quenching resistance and find optimum value. From this first set of results, a detailed study of the dark count rate (DCR) has been conducted. Our results show a dark count rate increase with the size of the photodiodes and the temperature (at T=22.5 °C, the DCR of a 10 µm-photodiode is 2020 count s{sup −1} while it is 270 count s{sup −1} at T=−40 °C for a overvoltage of 800 mV). A small pixel size is desirable, because the DCR per unit area decreases with the pixel size. We also found that the adjustment

  1. The Belle II Detector

    Science.gov (United States)

    Piilonen, Leo; Belle Collaboration, II

    2017-01-01

    The Belle II detector is now under construction at the KEK laboratory in Japan. This project represents a substantial upgrade of the Belle detector (and the KEKB accelerator). The Belle II experiment will record 50 ab-1 of data, a factor of 50 more than that recorded by Belle. This large data set, combined with the low backgrounds and high trigger efficiencies characteristic of an e+e- experiment, should provide unprecedented sensitivity to new physics signatures in B and D meson decays, and in τ lepton decays. The detector comprises many forefront subsystems. The vertex detector consists of two inner layers of silicon DEPFET pixels and four outer layers of double-sided silicon strips. These layers surround a beryllium beam pipe having a radius of only 10 mm. Outside of the vertex detector is a large-radius, small-cell drift chamber, an ``imaging time-of-propagation'' detector based on Cerenkov radiation for particle identification, and scintillating fibers and resistive plate chambers used to identify muons. The detector will begin commissioning in 2017.

  2. Disordered artificial spin ices: Avalanches and criticality (invited)

    Energy Technology Data Exchange (ETDEWEB)

    Reichhardt, Cynthia J. Olson, E-mail: cjrx@lanl.gov; Chern, Gia-Wei; Reichhardt, Charles [Center for Nonlinear Studies and Theoretical Division, Los Alamos National Laboratory, Los Alamos, New Mexico 87545 (United States); Libál, Andras [Faculty of Mathematics and Computer Science, Babes-Bolyai University, RO-400591 Cluj-Napoca (Romania)

    2015-05-07

    We show that square and kagome artificial spin ices with disconnected islands exhibit disorder-induced nonequilibrium phase transitions. The critical point of the transition is characterized by a diverging length scale and the effective spin reconfiguration avalanche sizes are power-law distributed. For weak disorder, the magnetization reversal is dominated by system-spanning avalanche events characteristic of a supercritical regime, while at strong disorder, the avalanche distributions have subcritical behavior and are cut off above a length scale that decreases with increasing disorder. The different type of geometrical frustration in the two lattices produces distinct forms of critical avalanche behavior. Avalanches in the square ice consist of the propagation of locally stable domain walls separating the two polarized ground states, and we find a scaling collapse consistent with an interface depinning mechanism. In the fully frustrated kagome ice, however, the avalanches branch strongly in a manner reminiscent of directed percolation. We also observe an interesting crossover in the power-law scaling of the kagome ice avalanches at low disorder. Our results show that artificial spin ices are ideal systems in which to study a variety of nonequilibrium critical point phenomena as the microscopic degrees of freedom can be accessed directly in experiments.

  3. Weak avalanche discrimination for gated-mode single-photon avalanche photodiodes.

    Science.gov (United States)

    Cho, Seok-Beom; Kang, Sae-Kyoung

    2011-09-12

    The after-pulsing effect is a common problem that needs to be overcome for high-speed single-photon detection based on gated-mode single-photon avalanche photodiodes (SPADs). This paper presents a simple and practical method for suppression of the after-pulsing probability using an auxiliary signal to discriminate quite weak avalanches. The detection efficiency and after-pulse probability of an InGaAs/InP SPAD are investigated with a 10 MHz gating for conventional and proposed methods, and a sharp decrease of after-pulse probability is demonstrated with the application of the proposed method. At a gating frequency of 100 MHz, a detection efficiency of 10.4% is achieved with an after-pulse probability of 5.6% without dead time.

  4. Statistical analyses support power law distributions found in neuronal avalanches.

    Directory of Open Access Journals (Sweden)

    Andreas Klaus

    Full Text Available The size distribution of neuronal avalanches in cortical networks has been reported to follow a power law distribution with exponent close to -1.5, which is a reflection of long-range spatial correlations in spontaneous neuronal activity. However, identifying power law scaling in empirical data can be difficult and sometimes controversial. In the present study, we tested the power law hypothesis for neuronal avalanches by using more stringent statistical analyses. In particular, we performed the following steps: (i analysis of finite-size scaling to identify scale-free dynamics in neuronal avalanches, (ii model parameter estimation to determine the specific exponent of the power law, and (iii comparison of the power law to alternative model distributions. Consistent with critical state dynamics, avalanche size distributions exhibited robust scaling behavior in which the maximum avalanche size was limited only by the spatial extent of sampling ("finite size" effect. This scale-free dynamics suggests the power law as a model for the distribution of avalanche sizes. Using both the Kolmogorov-Smirnov statistic and a maximum likelihood approach, we found the slope to be close to -1.5, which is in line with previous reports. Finally, the power law model for neuronal avalanches was compared to the exponential and to various heavy-tail distributions based on the Kolmogorov-Smirnov distance and by using a log-likelihood ratio test. Both the power law distribution without and with exponential cut-off provided significantly better fits to the cluster size distributions in neuronal avalanches than the exponential, the lognormal and the gamma distribution. In summary, our findings strongly support the power law scaling in neuronal avalanches, providing further evidence for critical state dynamics in superficial layers of cortex.

  5. Statistical analyses support power law distributions found in neuronal avalanches.

    Science.gov (United States)

    Klaus, Andreas; Yu, Shan; Plenz, Dietmar

    2011-01-01

    The size distribution of neuronal avalanches in cortical networks has been reported to follow a power law distribution with exponent close to -1.5, which is a reflection of long-range spatial correlations in spontaneous neuronal activity. However, identifying power law scaling in empirical data can be difficult and sometimes controversial. In the present study, we tested the power law hypothesis for neuronal avalanches by using more stringent statistical analyses. In particular, we performed the following steps: (i) analysis of finite-size scaling to identify scale-free dynamics in neuronal avalanches, (ii) model parameter estimation to determine the specific exponent of the power law, and (iii) comparison of the power law to alternative model distributions. Consistent with critical state dynamics, avalanche size distributions exhibited robust scaling behavior in which the maximum avalanche size was limited only by the spatial extent of sampling ("finite size" effect). This scale-free dynamics suggests the power law as a model for the distribution of avalanche sizes. Using both the Kolmogorov-Smirnov statistic and a maximum likelihood approach, we found the slope to be close to -1.5, which is in line with previous reports. Finally, the power law model for neuronal avalanches was compared to the exponential and to various heavy-tail distributions based on the Kolmogorov-Smirnov distance and by using a log-likelihood ratio test. Both the power law distribution without and with exponential cut-off provided significantly better fits to the cluster size distributions in neuronal avalanches than the exponential, the lognormal and the gamma distribution. In summary, our findings strongly support the power law scaling in neuronal avalanches, providing further evidence for critical state dynamics in superficial layers of cortex.

  6. IFKIS a basis for organizational measures in avalanche risk management

    Science.gov (United States)

    Bründl, M.; Etter, H.-J.; Klingler, Ch.; Steiniger, M.; Rhyner, J.; Ammann, W.

    2003-04-01

    The avalanche winter 1999 in Switzerland showed that the combination of protection measures like avalanche barriers, hazard zone mapping, artificial avalanche release and organisational measures (closure of roads, evacuation etc.) proved to perform well. However, education as well as information and communication between the involved organizations proved to be a weak link in the crisis management. In the first part of the project IFKIS we developed a modular education and training course program for security responsibles of settlements and roads. In the second part an information system was developed which improves on the one hand the information fluxes between the national center for avalanche forecasting, the Swiss Federal Institute for Snow and Avalanche Research SLF, and the local forecasters. On the other hand the communication between the avalanche security services in the communities can be enhanced. During the last two years an information system based on Internet technology has been developed for this purpose. This system allows the transmission of measured data and observations to a central database at SLF and visualization of the data for different users. It also provides the possibility to exchange information on organizational measures like closure of roads, artificial avalanche release etc. on a local and regional scale. This improves the information fluxes and the coordination of safety-measures because all users, although at different places, are on the same information level. Inconsistent safety-measures can be avoided and information and communication concerning avalanche safety becomes much more transparent for all persons involved in hazard management. The training program as well the concept for the information-system are important basics for an efficient avalanche risk management but also for other natural processes and catastrophes.

  7. Ultra-Fast Silicon Detectors for 4D tracking

    Science.gov (United States)

    Sola, V.; Arcidiacono, R.; Bellora, A.; Cartiglia, N.; Cenna, F.; Cirio, R.; Durando, S.; Ferrero, M.; Galloway, Z.; Gruey, B.; Freeman, P.; Mashayekhi, M.; Mandurrino, M.; Monaco, V.; Mulargia, R.; Obertino, M. M.; Ravera, F.; Sacchi, R.; Sadrozinski, H. F.-W.; Seiden, A.; Spencer, N.; Staiano, A.; Wilder, M.; Woods, N.; Zatserklyaniy, A.

    2017-02-01

    We review the progress toward the development of a novel type of silicon detectors suited for tracking with a picosecond timing resolution, the so called Ultra-Fast Silicon Detectors. The goal is to create a new family of particle detectors merging excellent position and timing resolution with GHz counting capabilities, very low material budget, radiation resistance, fine granularity, low power, insensitivity to magnetic field, and affordability. We aim to achieve concurrent precisions of ~ 10 ps and ~ 10 μm with a 50 μm thick sensor. Ultra-Fast Silicon Detectors are based on the concept of Low-Gain Avalanche Detectors, which are silicon detectors with an internal multiplication mechanism so that they generate a signal which is factor ~ 10 larger than standard silicon detectors.

  8. III-V alloy heterostructure high speed avalanche photodiodes

    Science.gov (United States)

    Law, H. D.; Nakano, K.; Tomasetta, L. R.

    1979-01-01

    Heterostructure avalanche photodiodes have been successfully fabricated in several III-V alloy systems: GaAlAs/GaAs, GaAlSb/GaAlSb, and InGaAsP/InP. These diodes cover optical wavelengths from 0.4 to 1.8 micron. Early stages of development show very encouraging results. High speed response of less than 35 ps and high quantum efficiency more than 95 percent have been obtained. The dark currents and the excess avalanche noise are also dicussed. A direct comparison of GaAlSb, GaAlAsSb, and In GaAsP avalanche photodiodes is given.

  9. Anthropogenic effect on avalanche and debris flow activity

    Directory of Open Access Journals (Sweden)

    S. A. Sokratov

    2013-01-01

    Full Text Available The paper presents examples of the change in snow avalanches and debris flows activity due to the anthropogenic pressure on vegetation and relief. The changes in dynamical characteristics of selected snow avalanches and debris flows due to the anthropogenic activity are quantified. The conclusion is made that the anthropogenic effects on the snow avalanches and debris flows activity are more pronounced than the possible effects of the climate change. The necessity is expressed on the unavoidable changes of the natural environment as the result of a construction and of use of the constructed infrastructure to be account for in corresponding planning of the protection measures.

  10. Seeded excitation avalanches in off-resonantly driven Rydberg gases

    CERN Document Server

    Simonelli, Cristiano; Masella, Guido; Asteria, Luca; Arimondo, Ennio; Ciampini, Donatella; Morsch, Oliver

    2016-01-01

    We report an experimental investigation of the facilitated excitation dynamics in off-resonantly driven Rydberg gases by separating the initial off-resonant excitation phase from the facilitation phase, in which successive facilitation events lead to excitation avalanches. We achieve this by creating a controlled number of initial seed excitations. Greater insight into the avalanche mechanism is obtained from an analysis of the full counting distributions. We also present simple mathematical models and numerical simulations of the excitation avalanches that agree well with our experimental results.

  11. Avalanche of particles in evaporating coffee drops

    CERN Document Server

    Marin, Alvaro G; Snoeijer, Jacco; Lohse, Detlef

    2010-01-01

    The pioneering work of Deegan et al. [Nature 389, (1997)] showed how a drying sessile droplet suspension of particles presents a maximum evaporating flux at its contact line which drags liquid and particles creating the well known coffee stain ring. In this Fluid Dynamics Video, measurements using micro Particle Image Velocimetry and Particle Tracking clearly show an avalanche of particles being dragged in the last moments, for vanishing contact angles and droplet height. This explains the different characteristic packing of the particles in the layers of the ring: the outer one resembles a crystalline array, while the inner one looks more like a jammed granular fluid. Using the basic hydrodynamic model used by Deegan et al. [Phys. Rev. E 62, (2000)] it will be shown how the liquid radial velocity diverges as the droplet life comes to an end, yielding a good comparison with the experimental data.

  12. Photon counting techniques with silicon avalanche photodiodes.

    Science.gov (United States)

    Dautet, H; Deschamps, P; Dion, B; Macgregor, A D; Macsween, D; McIntyre, R J; Trottier, C; Webb, P P

    1993-07-20

    The properties of avalanche photodiodes and associated electronics required for photon counting in the Geiger and the sub-Geiger modes are reviewed. When the Geiger mode is used, there are significant improvements reported in overall photon detection efficiencies (approaching 70% at 633 nm), and a timing jitter (under 200 ps) is achieved with passive quenching at high overvoltages (20-30 V). The results obtained by using an active-mode fast quench circuit capable of switching overvoltages as high as 15 V (giving photon detection efficiencies in the 50% range) with a dead time of less than 50 ns are reported. Larger diodes (up to 1 mm in diameter) that are usable in the Geiger mode and that have quantum efficiencies over 80% in the 500-800-nm range are also reported.

  13. Avalanche photodiodes now and possible developments

    CERN Document Server

    Britvitch, I; Ingram, Q; Kuznetsov, A; Musienko, Y; Renker, D; Reucroft, S; Sakhelashvili, T M; Swain, J

    2004-01-01

    Avalanche Photodiodes (APDs) are now out of their infancy and are used in large numbers in the electromagnetic calorimeter of CMS where they have to stand the extremely hostile environment of LHC. This type - with smaller sensitive area and arranged in monolithic arrays - is an excellent candidate for the read out of scintillating crystals in medical imaging and a PET scanner operates already successfully since more than 3 years. We present the properties of the device used in CMS and possible improvements of the structure, which could open the door for new applications. Operating APDs at low temperatures or in Geiger mode will allow single photon counting and in future they could replace photomultiplier tubes.

  14. Overspill avalanching in a dense reservoir network

    CERN Document Server

    Mamede, G L; Schneider, C M; de Araújo, J C; Herrmann, H J

    2012-01-01

    Sustainability of communities, agriculture, and industry is strongly dependent on an effective storage and supply of water resources. In some regions the economic growth has led to a level of water demand which can only be accomplished through efficient reservoir networks. Such infrastructures are not always planned at larger scale but rather made by farmers according to their local needs of irrigation during droughts. Based on extensive data from the upper Jaguaribe basin, one of the world's largest system of reservoirs, located in the Brazilian semiarid northeast, we reveal that surprisingly it self-organizes into a scale-free network exhibiting also a power-law in the distribution of the lakes and avalanches of discharges. With a new self-organized-criticality-type model we manage to explain the novel critical exponents. Implementing a flow model we are able to reproduce the measured overspill evolution providing a tool for catastrophe mitigation and future planning.

  15. Lautaret avalanche test site: outcomes from the 11th april 2012 event

    OpenAIRE

    2012-01-01

    International audience; The Lautaret full-scale avalanche test site has been used by Cemagref-Irstea since the early 70's. The first studies were dedicated to avalanche released systems. Later, experiments focused on avalanche dynamics and avalanche impact pressures both in relation with the fundamental knowledge of snow flow rheology and the engineering of defense structures and avalanche hazard zoning. Recent instrumentation developments now provide rich-documented in situ measurements of a...

  16. Development in the design and performance of gas avalanche microdetectors (MSGC, MGC, and MDOT)

    Energy Technology Data Exchange (ETDEWEB)

    Cho, Hyo-Sung [Univ. of California, Berkeley, CA (United States). Dept. of Nuclear Enginering

    1997-12-01

    There has been continuing development of generic classes of microstrip gas chambers (MSGCs), microgap gas chambers (MGCs) and microdot gas chambers (MDOTs) at Lawrence Berkeley National Laboratory (LBNL) over the past few years, to improve such detectors beyond their present capabilities, to produce detectors suitable for use in current or upcoming experiments, and to allow a basis for new R&D developments which may incorporate these detectors as part of the system. All of these new detectors are collectively referred to as "gas avalanche microdetectors". The MSGC, which was motivated by the pioneering work of A. Oed, has many attractive features, especially excellent spatial resolution (~30 μm rms at normal incidence) and high rate capability (~106 mm-2∙s-1). Moreover, the MGC seems to have certain advantages over the MSGC in speed, stability and simplicity, and the MDOT has larger gain (>104) and the intrinsic advantages of two-dimensional readout. Because of these attractive properties, they have received a great deal of attention for nuclear and high energy physics experiments, medical X-ray imaging and many other fields requiring radiation detection and measurement.

  17. Detectors - Electronics; Detecteurs - Electronique

    Energy Technology Data Exchange (ETDEWEB)

    Bregeault, J.; Gabriel, J.L.; Hierle, G.; Lebotlan, P.; Leconte, A.; Lelandais, J.; Mosrin, P.; Munsch, P.; Saur, H.; Tillier, J. [Lab. de Physique Corpusculaire, Caen Univ., 14 (France)

    1998-04-01

    The reports presents the main results obtained in the fields of radiation detectors and associated electronics. In the domain of X-ray gas detectors for the keV range efforts were undertaken to rise the detector efficiency. Multiple gap parallel plate chambers of different types as well as different types of X {yields} e{sup -} converters were tested to improve the efficiency (values of 2.4% at 60 KeV were reached). In the field of scintillators a study of new crystals has been carried out (among which Lutetium orthosilicate). CdTe diode strips for obtaining X-ray imaging were studied. The complete study of a linear array of 8 CdTe pixels has been performed and certified. The results are encouraging and point to this method as a satisfying solution. Also, a large dimension programmable chamber was used to study the influence of temperature on the inorganic scintillators in an interval from -40 deg. C to +150 deg. C. Temperature effects on other detectors and electronic circuits were also investigated. In the report mentioned is also the work carried out for the realization of the DEMON neutron multidetector. For neutron halo experiments different large area Si detectors associated with solid and gas position detectors were realized. In the frame of a contract with COGEMA a systematic study of Li doped glasses was undertaken aiming at replacing with a neutron probe the {sup 3}He counters presently utilized in pollution monitoring. An industrial prototype has been realised. Other studies were related to integrated analog chains, materials for Cherenkov detectors, scintillation probes for experiments on fundamental processes, gas position sensitive detectors, etc. In the field of associated electronics there are mentioned the works related to the multidetector INDRA, data acquisition, software gamma spectrometry, automatic gas pressure regulation in detectors, etc

  18. Simultaneous data communication and position sensing with an impact ionization engineered avalanche photodiode array for free space optical communication

    Science.gov (United States)

    Ferraro, Mike S.; Mahon, Rita; Rabinovich, William S.; Murphy, James L.; Dexter, James L.; Clark, William R.; Waters, William D.; Vaccaro, Kenneth; Krejca, Brian D.

    2017-02-01

    Photodetectors in free space optical communication systems perform two functions: reception of data communication signals and position sensing for pointing, tracking, and stabilization. Traditionally, the optical receive path in an FSO system is split into separate paths for data detection and position sensing. The need for separate paths is a consequence of conflicting performance criteria between position sensitive detectors (PSD) and data detectors. Combining the functionality of both detector types requires that the combinational sensor not only have the bandwidth to support high data rate communication but the active area and spatial discrimination to accommodate position sensing. In this paper we present a large area, concentric five element impact ionization engineered avalanche photodiode array rated for bandwidths beyond 1GHz with a measured carrier ionization ratio of less than 0.1 at moderate APD gains. The integration of this array as a combinational sensor in an FSO system is discussed along with the development of a pointing and stabilization algorithm.

  19. 3D integration of Geiger-mode avalanche photodiodes aimed to very high fill-factor pixels for future linear colliders 

    CERN Document Server

    Vilella, E; Dieguez, A

    2013-01-01

    This paper presents an analysis of the maximum achievable fill-factor by a pixel detector of Geiger-mode avalanche photodiodes with the Chartered 130 nm/Tezzaron 3D process. The analysis shows that fillfactors between 66% and 96% can be obtained with different array architectures and a time-gated readout circuit of minimum area. The maximum fill-factor is achieved when the two-layer vertical stack is used to overlap the non-sensitive areas of one layer with the sensitive areas of the other one. Moreover, different sensor areas are used to further increase the fill-factor. A chip containing a pixel detector of the Geigermode avalanche photodiodes and aimed to future linear colliders has been designed with the Chartered 130 nm/Tezzaron 3D process to increase the fill-factor.

  20. 3D integration of Geiger-mode avalanche photodiodes aimed to very high fill-factor pixels for future linear colliders

    Science.gov (United States)

    Vilella, E.; Alonso, O.; Diéguez, A.

    2013-12-01

    This paper presents an analysis of the maximum achievable fill-factor by a pixel detector of Geiger-mode avalanche photodiodes with the Chartered 130 nm/Tezzaron 3D process. The analysis shows that fill-factors between 66% and 96% can be obtained with different array architectures and a time-gated readout circuit of minimum area. The maximum fill-factor is achieved when the two-layer vertical stack is used to overlap the non-sensitive areas of one layer with the sensitive areas of the other one. Moreover, different sensor areas are used to further increase the fill-factor. A chip containing a pixel detector of the Geiger-mode avalanche photodiodes and aimed to future linear colliders has been designed with the Chartered 130 nm/Tezzaron 3D process to increase the fill-factor.

  1. SiC Avalanche Photodiodes and Arrays Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Aymont Technology, Inc. (Aymont) will demonstrate the feasibility of SiC p-i-n avalanche photodiodes (APD) arrays. Aymont will demonstrate 4 x 4 arrays of 2 mm2 APDs...

  2. Relative degradation of near infrared avalanche photodiodes from proton irradiation

    Science.gov (United States)

    Becker, Heidi; Johnston, Allan H.

    2004-01-01

    InGaAs and Ge avalanche photodiodes are compared for the effects of 63-MeV protons on dark current. Differences in displacement damage factors are discussed as they relate to structural differences between devices.

  3. Relative degradation of near infrared avalanche photodiodes from proton irradiation

    Science.gov (United States)

    Becker, Heidi; Johnston, Allan H.

    2004-01-01

    InGaAs and Ge avalanche photodiodes are compared for the effects of 63-MeV protons on dark current. Differences in displacement damage factors are discussed as they relate to structural differences between devices.

  4. Non-linear behaviour of large-area avalanche photodiodes

    CERN Document Server

    Fernandes, L M P; Monteiro, C M B; Santos, J M; Morgado, R E

    2002-01-01

    The characterisation of photodiodes used as photosensors requires a determination of the number of electron-hole pairs produced by scintillation light. One method involves comparing signals produced by X-ray absorptions occurring directly in the avalanche photodiode with the light signals. When the light is derived from light-emitting diodes in the 400-600 nm range, significant non-linear behaviour is reported. In the present work, we extend the study of the linear behaviour to large-area avalanche photodiodes, of Advanced Photonix, used as photosensors of the vacuum ultraviolet (VUV) scintillation light produced by argon (128 nm) and xenon (173 nm). We observed greater non-linearities in the avalanche photodiodes for the VUV scintillation light than reported previously for visible light, but considerably less than the non-linearities observed in other commercially available avalanche photodiodes.

  5. Dynamic intermittency in discrete erodible-bed avalanches

    Science.gov (United States)

    Arran, Matthew; Vriend, Nathalie

    2016-11-01

    The coexistence of fluid-like and solid-like behaviour in granular matter allows avalanches of grains to flow on the surface of a static but erodible bed. For sufficiently slow inflow, these avalanches are discrete, with previous experimentalists reporting that avalanche fronts pass a given point quasi-periodically. We report instead observations of dynamic intermittency between two regimes, one in which avalanches occur quasi-periodically and another in which the intervals between them are irregular. Finding the first regime consistent with existing models, we introduce a model for the second regime within the framework of Self-Organised Criticality, and describe the transition between the regimes with reference to the state of the erodible bed.

  6. Avalanche statistics from data with low time resolution.

    Science.gov (United States)

    LeBlanc, Michael; Nawano, Aya; Wright, Wendelin J; Gu, Xiaojun; Uhl, J T; Dahmen, Karin A

    2016-11-01

    Extracting avalanche distributions from experimental microplasticity data can be hampered by limited time resolution. We compute the effects of low time resolution on avalanche size distributions and give quantitative criteria for diagnosing and circumventing problems associated with low time resolution. We show that traditional analysis of data obtained at low acquisition rates can lead to avalanche size distributions with incorrect power-law exponents or no power-law scaling at all. Furthermore, we demonstrate that it can lead to apparent data collapses with incorrect power-law and cutoff exponents. We propose new methods to analyze low-resolution stress-time series that can recover the size distribution of the underlying avalanches even when the resolution is so low that naive analysis methods give incorrect results. We test these methods on both downsampled simulation data from a simple model and downsampled bulk metallic glass compression data and find that the methods recover the correct critical exponents.

  7. UNIQUENESS OF SOLUTIONS FOR SEMICONDUCTOR EQUATIONS WITH AVALANCHE TERM

    Institute of Scientific and Technical Information of China (English)

    Xing Jiasheng; Wang Yuanming

    2000-01-01

    In this paper, we consider the initial and mixed boundary value problems for the semiconductor equations with avalanche term, the uniqueness of the weak solution for the semiconductor equation has been proved.

  8. Geiger-Mode Avalanche Photodiodes in Particle Detection

    OpenAIRE

    Vilella, E.; Alonso, O.; Trenado, J.; Vilà, A.; De Vos, M.; Garrido, L.; Diéguez, A.

    2012-01-01

    It is well known that avalanche photodiodes operated in the Geiger mode above the breakdown voltage offer a virtually infinite sensitivity and time accuracy in the picosecond range that can be used for single photon detection. However, their performance in particle detection remains still unexplored. In this contribution, we are going to expose the different steps that we have taken in order to prove the efficiency of Geiger mode avalanche photodiodes in the aforementioned field. In particula...

  9. Wavelength dependence of silicon avalanche photodiode fabricated by CMOS process

    Science.gov (United States)

    Mohammed Napiah, Zul Atfyi Fauzan; Hishiki, Takuya; Iiyama, Koichi

    2017-07-01

    Avalanche photodiodes fabricated by CMOS process (CMOS-APDs) have features of high avalanche gain below 10 V, wide bandwidth over 5 GHz, and easy integration with electronic circuits. In CMOS-APDs, guard ring structure is introduced for high-speed operation by canceling photo-generated carriers in the substrate at the sacrifice of the responsivity. We describe here wavelength dependence of the responsivity and the bandwidth of the CMOS-APDs with shorted and opened guard ring structure.

  10. Influence of snow-cover properties on avalanche dynamics

    Science.gov (United States)

    Steinkogler, W.; Sovilla, B.; Lehning, M.

    2012-04-01

    Snow avalanches with the potential of reaching traffic routes and settlements are a permanent winter threat for many mountain communities. Snow safety officers have to take the decision whether to close a road, a railway line or a ski slope. Those decisions are often very difficult as they demand the ability to interpret weather forecasts, to establish their implication for the stability and the structure of the snow cover and to evaluate the influence of the snow cover on avalanche run-out distances. In the operational programme 'Italy-Switzerland, project STRADA' we focus on the effects of snow cover on avalanche dynamics, and thus run-out distance, with the aim to provide a better understanding of this influence and to ultimately develop tools to support snow safety officers in their decision process. We selected five avalanches, measured at the Vallée de la Sionne field site, with similar initial mass and topography but different flow dynamics and run-out distances. Significant differences amongst the individual avalanches could be observed for front and internal velocities, impact pressures, flow regimes, deposition volumes and run-out distances. For each of these avalanches, the prevailing snow conditions at release were reconstructed using field data from local snowpits or were modeled with SNOWPACK. Combining flow dynamical data with snow cover properties shows that erodible snow depth, snow density and snow temperature in the snow pack along the avalanche track are among the decisive variables that appear to explain the observed differences. It is further discussed, how these influencing factors can be quantified and used for improved predictions of site and time specific avalanche hazard.

  11. Effect of volume fraction on granular avalanche dynamics.

    Science.gov (United States)

    Gravish, Nick; Goldman, Daniel I

    2014-09-01

    We study the evolution and failure of a granular slope as a function of prepared volume fraction, ϕ(0). We rotated an initially horizontal layer of granular material (0.3-mm-diam glass spheres) to a 45° angle while we monitor the motion of grains from the side and top with high-speed video cameras. The dynamics of grain motion during the tilt process depended sensitively on ϕ(0)∈[0.58-0.63] and differed above or below the granular critical state, ϕ(c), defined as the onset of dilation as a function of increasing volume fraction. For ϕ(0)-ϕ(c)avalanche. Precursor compaction events began at an initial angle θ(0)=7.7±1.4° and occurred intermittently prior to the onset of an avalanche. Avalanches occurred at the maximal slope angle θ(m)=28.5±1.0°. Granular material at ϕ(0)-ϕ(c)>0 did not experience precursor compaction prior to avalanche flow, and instead experienced a single dilational motion at θ(0)=32.1±1.5° prior to the onset of an avalanche at θ(m)=35.9±0.7°. Both θ(0) and θ(m) increased with ϕ(0) and approached the same value in the limit of random close packing. The angle at which avalanching grains came to rest, θ(R)=22±2°, was independent of ϕ(0). From side-view high-speed video, we measured the velocity field of intermittent and avalanching flow. We found that flow direction, depth, and duration were affected by ϕ(0), with ϕ(0)-ϕ(c)0. Our study elucidates how initial conditions-including volume fraction-are important determinants of granular slope stability and the onset of avalanches.

  12. Avalanche Phenomenon of Runaway Electrons During Additional Fuelling

    Institute of Scientific and Technical Information of China (English)

    杨进蔚; 曹建勇; 曾庆希; 张炜; 唐年益; 董贾福; 邓中朝; 肖正贵; 姚良骅

    2002-01-01

    During pellet injection and supersonic molecular beam injection, we have observed the increase of electron density and the enhancement of hard x-ray radiation, but the runaway electrons normally decrease without additional fuelling when the density of plasma increases. This phenomenon may come from the synergetic effects of Dreicer and avalanche runaway electrons. The experimental results are consistent with the calculation based on the theory of avalanche runaway in the HL-1M tokamak.

  13. Avalanche robustness of SiC Schottky diode

    OpenAIRE

    Dchar, Ilyas; Buttay, Cyril; Morel, Hervé

    2016-01-01

    International audience; Reliability is one of the key issues for the application of Silicon carbide (SiC) diode in high power conversion systems. For instance, in high voltage direct current (HVDC) converters, the devices can be submitted to high voltage transients which yield to avalanche. This paper presents the experimental evaluation of SiC diodes submitted to avalanche, and shows that the energy dissipation in the device can increase quickly and will not be uniformly distributed across t...

  14. First Avalanche-photodiode camera test (FACT): A novel camera using G-APDs for the observation of very high-energy {gamma}-rays with Cherenkov telescopes

    Energy Technology Data Exchange (ETDEWEB)

    Braun, I. [ETH Zurich, CH-8093 Zurich (Switzerland); Commichau, S.C. [ETH Zurich, CH-8093 Zurich (Switzerland)], E-mail: commichau@phys.ethz.ch; Rissi, M. [ETH Zurich, CH-8093 Zurich (Switzerland); Backes, M. [Dortmund University of Technology, D-44221 Dortmund (Germany); Biland, A. [ETH Zurich, CH-8093 Zurich (Switzerland); Bretz, T. [University of Wuerzburg, D-97074 Wuerzburg (Germany); Britvitch, I.; Commichau, V.; Gunten, H. von; Hildebrand, D.; Horisberger, U.; Kranich, D. [ETH Zurich, CH-8093 Zurich (Switzerland); Lorenz, E. [ETH Zurich, CH-8093 Zurich (Switzerland); Max-Planck-Institut fuer Physik, D-80805 Muenchen (Germany); Lustermann, W. [ETH Zurich, CH-8093 Zurich (Switzerland); Mannheim, K. [University of Wuerzburg, D-97074 Wuerzburg (Germany); Neise, D. [Dortmund University of Technology, D-44221 Dortmund (Germany); Pauss, F. [ETH Zurich, CH-8093 Zurich (Switzerland); Pohl, M. [University of Geneva, CH-1211 Geneva (Switzerland); Renker, D. [Paul Scherrer Institut (PSI) Villigen, CH-5232 Villigen (Switzerland); Rhode, W. [Dortmund University of Technology, D-44221 Dortmund (Germany)] (and others)

    2009-10-21

    We present a project for a novel camera using Geiger-mode Avalanche Photodiodes (G-APDs), to be installed in a small telescope (former HEGRA CT3) on the MAGIC site in La Palma (Canary Island, Spain). This novel type of semiconductor photon detector provides several superior features compared to conventional photomultiplier tubes (PMTs). The most promising one is a much higher Photon Detection Efficiency.

  15. Characterisation of Silicon Timing Detectors for the RD50 Collaboration

    CERN Document Server

    Immig, David Maximilian

    2017-01-01

    Increasing pile-up and irradiation following with the high luminosity upgrade of the LHC, demands the development of improved semiconductor detectors. The former problem can be reduced by more precise time information, which can be obtained using a future detector based on the low gain avalanche diode (LGAD). LGADs are studied by the RD50-Collaboration, which studies the characteristics of semiconductor devices to improve these for future requirements of high energy physics. This reports is engaged with the process to characterise semiconductor detectors, specially LGADs, with capacitance-voltage and current-voltage measurements as well as transient current techniques of un- and irradiated semiconductor devices.

  16. Single photonics at telecom wavelengths using nanowire superconducting detectors

    CERN Document Server

    Zinoni, C; Fiore, A; Gerardino, A; Goltsman, G N; Li, L H; Lunghi, L; Marsili, F; Smirnov, K V; Vakhtomin, Y B; Vakhtomin, Yu. B.

    2006-01-01

    Single photonic applications - such as quantum key distribution - rely on the transmission of single photons, and require the ultimate sensitivity that an optical detector can achieve. Single-photon detectors must convert the energy of an optical pulse containing a single photon into a measurable electrical signal. We report on fiber-coupled superconducting single-photon detectors (SSPDs) with specifications that exceed those of avalanche photodiodes (APDs), operating at telecommunication wavelength, in sensitivity, temporal resolution and repetition frequency. The improved performance is demonstrated by measuring the intensity correlation function g(2)(t) of single-photon states at 1300nm produced by single semiconductor quantum dots (QDs).

  17. Spatio-temporal avalanche forecasting with Support Vector Machines

    Directory of Open Access Journals (Sweden)

    A. Pozdnoukhov

    2011-02-01

    Full Text Available This paper explores the use of the Support Vector Machine (SVM as a data exploration tool and a predictive engine for spatio-temporal forecasting of snow avalanches. Based on the historical observations of avalanche activity, meteorological conditions and snowpack observations in the field, an SVM is used to build a data-driven spatio-temporal forecast for the local mountain region. It incorporates the outputs of simple physics-based and statistical approaches used to interpolate meteorological and snowpack-related data over a digital elevation model of the region. The interpretation of the produced forecast is discussed, and the quality of the model is validated using observations and avalanche bulletins of the recent years. The insight into the model behaviour is presented to highlight the interpretability of the model, its abilities to produce reliable forecasts for individual avalanche paths and sensitivity to input data. Estimates of prediction uncertainty are obtained with ensemble forecasting. The case study was carried out using data from the avalanche forecasting service in the Locaber region of Scotland, where avalanches are forecast on a daily basis during the winter months.

  18. Repertoires of spike avalanches are modulated by behavior and novelty

    Directory of Open Access Journals (Sweden)

    Tiago Lins Ribeiro

    2016-03-01

    Full Text Available Neuronal avalanches measured as consecutive bouts of thresholded field potentials represent a statistical signature that the brain operates near a critical point. In theory, criticality optimizes stimulus sensitivity, information transmission, computational capability and mnemonic repertoires size. Field potential avalanches recorded via multielectrode arrays from cortical slice cultures are repeatable spatiotemporal activity patterns. It remains unclear whether avalanches of action potentials observed in forebrain regions of freely-behaving rats also form recursive repertoires, and whether these have any behavioral relevance. Here we show that spike avalanches, recorded from hippocampus and sensory neocortex of freely-behaving rats, constitute distinct families of recursive spatiotemporal patterns. A significant number of those patterns were specific to a behavioral state. Although avalanches produced during sleep were mostly similar to others that occurred during waking, the repertoire of patterns recruited during sleep differed significantly from that of waking. More importantly, exposure to novel objects increased the rate at which new patterns arose, also leading to changes in post-exposure repertoires, which were significantly different from those before the exposure. A significant number of families occurred exclusively during periods of whisker contact with objects, but few were associated with specific objects. Altogether, the results provide original evidence linking behavior and criticality at the spike level: spike avalanches form repertoires that emerge in waking, recur during sleep, are diversified by novelty and contribute to object representation.

  19. Repertoires of Spike Avalanches Are Modulated by Behavior and Novelty.

    Science.gov (United States)

    Ribeiro, Tiago L; Ribeiro, Sidarta; Copelli, Mauro

    2016-01-01

    Neuronal avalanches measured as consecutive bouts of thresholded field potentials represent a statistical signature that the brain operates near a critical point. In theory, criticality optimizes stimulus sensitivity, information transmission, computational capability and mnemonic repertoires size. Field potential avalanches recorded via multielectrode arrays from cortical slice cultures are repeatable spatiotemporal activity patterns. It remains unclear whether avalanches of action potentials observed in forebrain regions of freely-behaving rats also form recursive repertoires, and whether these have any behavioral relevance. Here, we show that spike avalanches, recorded from hippocampus (HP) and sensory neocortex of freely-behaving rats, constitute distinct families of recursive spatiotemporal patterns. A significant number of those patterns were specific to a behavioral state. Although avalanches produced during sleep were mostly similar to others that occurred during waking, the repertoire of patterns recruited during sleep differed significantly from that of waking. More importantly, exposure to novel objects increased the rate at which new patterns arose, also leading to changes in post-exposure repertoires, which were significantly different from those before the exposure. A significant number of families occurred exclusively during periods of whisker contact with objects, but few were associated with specific objects. Altogether, the results provide original evidence linking behavior and criticality at the spike level: spike avalanches form repertoires that emerge in waking, recur during sleep, are diversified by novelty and contribute to object representation.

  20. A revision of the Haiming rock avalanche (Eastern Alps)

    Science.gov (United States)

    Dufresne, Anja; Ostermann, Marc; Kelfoun, Karim; Ring, Max; Asam, Dario; Prager, Christoph

    2016-04-01

    The carbonate Haiming rock avalanche is directly neighbouring the larger Tschirgant rock avalanche deposit, both located in the upper Inn valley (Tyrol, Austria). Based on detailed morpho-lithologic mapping of the deposit, which has not been done at Haiming before, the sedimentology of the Holocene landslide debris is characterised. Structural-tectonic elements of the bedrock units at the scarp area are supplemented with borehole data from drillings at the source area giving valuable insights into the complex geological bedrock composition and structure. New source and runout reconstructions allow updated volumetric calculations, which are subsequently integrated into numerical runout modelling. Haiming is one of few topographically unobstructed rock avalanches, yet its morphology was greatly influenced by fluvial terraces, which are still discernible through the deposit on LiDAR hillshade images. We also address the influence of the rock avalanche on the valley floor and local river system as a short-lived dam and its interaction with fluvial incision. Finally, we discuss the Haiming rock avalanche in view of the other massive rock slope failures in the area ("Fernpass cluster"), their spatio-temporal distribution, and point out further highlights of this simple(?) rock avalanche deposit.

  1. Avalanches, plasticity, and ordering in colloidal crystals under compression.

    Science.gov (United States)

    McDermott, D; Reichhardt, C J Olson; Reichhardt, C

    2016-06-01

    Using numerical simulations we examine colloids with a long-range Coulomb interaction confined in a two-dimensional trough potential undergoing dynamical compression. As the depth of the confining well is increased, the colloids move via elastic distortions interspersed with intermittent bursts or avalanches of plastic motion. In these avalanches, the colloids rearrange to minimize their colloid-colloid repulsive interaction energy by adopting an average lattice constant that is isotropic despite the anisotropic nature of the compression. The avalanches take the form of shear banding events that decrease or increase the structural order of the system. At larger compression, the avalanches are associated with a reduction of the number of rows of colloids that fit within the confining potential, and between avalanches the colloids can exhibit partially crystalline or anisotropic ordering. The colloid velocity distributions during the avalanches have a non-Gaussian form with power-law tails and exponents that are consistent with those found for the velocity distributions of gliding dislocations. We observe similar behavior when we subsequently decompress the system, and find a partially hysteretic response reflecting the irreversibility of the plastic events.

  2. Avalanches and hysteresis in frustrated superconductors and XY spin glasses.

    Science.gov (United States)

    Sharma, Auditya; Andreanov, Alexei; Müller, Markus

    2014-10-01

    We study avalanches along the hysteresis loop of long-range interacting spin glasses with continuous XY symmetry, which serves as a toy model of granular superconductors with long-range and frustrated Josephson couplings. We identify sudden jumps in the T=0 configurations of the XY phases as an external field is increased. They are initiated by the softest mode of the inverse susceptibility matrix becoming unstable, which induces an avalanche of phase updates (or spin alignments). We analyze the statistics of these events and study the correlation between the nonlinear avalanches and the soft mode that initiates them. We find that the avalanches follow the directions of a small fraction of the softest modes of the inverse susceptibility matrix, similarly as was found in avalanches in jammed systems. In contrast to the similar Ising spin glass (Sherrington-Kirkpatrick) studied previously, we find that avalanches are not distributed with a scale-free power law but rather have a typical size which scales with the system size. We also observe that the Hessians of the spin-glass minima are not part of standard random matrix ensembles as the lowest eigenvector has a fractal support.

  3. Low noise InGaAs/InP single-photon negative feedback avalanche diodes: characterization and applications

    Science.gov (United States)

    Boso, Gianluca; Korzh, Boris; Lunghi, Tommaso; Zbinden, Hugo

    2015-05-01

    In recent years, many applications have been proposed that require detection of light signals in the near-infrared range with single-photon sensitivity and time resolution down to few hundreds of picoseconds. InGaAs/InP singlephoton avalanche diodes (SPADs) are a viable choice for these tasks thanks to their compactness and ease-of-use. Unfortunately, their performance is traditionally limited by high dark count rates (DCRs) and afterpulsing effects. However, a recent demonstration of negative feedback avalanche diodes (NFADs), operating in the free-running regime, achieved a DCR down to 1 cps at 10 % photon detection efficiency (PDE) at telecom wavelengths. Here we present our recent results on the characterization of NFAD detectors for temperatures down to approximately 150 K. A FPGA controlled test-bench facilitates the acquisition of all the parameters of interest like PDE, DCR, afterpulsing probability etc. We also demonstrate the performance of the detector in different applications: In particular, with low-temperature NFADs, we achieved high secret key rates with quantum key distribution over fiber links between 100-300 km. But low noise InGaAs/InP SPADs will certainly find applications in yet unexplored fields like photodynamic therapy, near infrared diffuse optical spectroscopy and many more. For example with a large area detector, we made time-resolved measurements of singlet-oxygen luminescence from a standard Rose Bengal dye in aqueous solution.

  4. A view on progress of silicon single-photon avalanche diodes and quenching circuits

    Science.gov (United States)

    Cova, Sergio; Ghioni, Massimo; Zappa, Franco; Rech, Ivan; Gulinatti, Angelo

    2006-10-01

    Silicon Single-Photon Avalanche-Diodes (SPAD) are nowadays considered a solid-state alternative to Photomultiplier Tubes (PMT) in single photon counting (SPC) and time-correlated single photon-counting (TCSPC) over the visible spectral range up to 1 micron wavelength. SPADs implemented in planar epitaxial technology compatible with CMOS circuits offer the typical advantages of microelectronic devices (small size, ruggedness, low voltage and low power, etc.). Furthermore, they have inherently higher photon detection efficiency, since they do not rely on electron emission in vacuum from a photocathode as PMT, but instead on the internal photoelectric effect. However, PMTs offer much wider sensitive area, which greatly simplifies the design of optical systems; they provide position-sensitive photon detection and imaging capability; they attain remarkable performance at high counting rate and offer picosecond timing resolution with Micro-Channel Plate (MCP) models. In order to make SPADs more competitive in a broader range of SPC and TCPC applications it is necessary to face both semiconductor technology issues and circuit design issues, which will be here dealt with. Technology issues will be discussed in the context of two possible approaches: employing a standard industrial high-voltage compatible CMOS technology or developing a dedicated CMOS-compatible technology. Circuit design issues will be discussed taking into account problems arising from conflicting requirements set by various required features, such as fast and efficient avalanche quenching and reset, high resolution photon timing, etc.

  5. Gated Geiger mode avalanche photodiode pixels with integrated readout electronics for low noise photon detection

    Science.gov (United States)

    Vilella, E.; Comerma, A.; Alonso, O.; Gascon, D.; Diéguez, A.

    2012-12-01

    Avalanche photodiodes operated in the Geiger mode offer a high intrinsic gain as well as an excellent timing accuracy. These qualities make the sensor specially suitable for those applications where detectors with high sensitivity and low timing uncertainty are required. Moreover, they are compatible with standard CMOS technologies, allowing sensor and front-end electronics integration within the pixel cell. However, the sensor suffers from high levels of intrinsic noise, which may lead to erroneous results and limit the range of detectable signals. They also increase the amount of data that has to be stored. In this work, we present a pixel based on a Geiger-mode avalanche photodiode operated in the gated mode to reduce the probability to detect noise counts interfering with photon arrival events. The readout circuit is based on a two grounds scheme to enable low reverse bias overvoltages and consequently lessen the dark count rate. Experimental characterization of the fabricated pixel with the HV-AMS 0.35 μm standard technology is also presented in this article.

  6. Gated Geiger mode avalanche photodiode pixels with integrated readout electronics for low noise photon detection

    Energy Technology Data Exchange (ETDEWEB)

    Vilella, E., E-mail: evilella@el.ub.es [Department of Electronics, University of Barcelona (UB) Marti i Franques 1, 08028 Barcelona (Spain); Comerma, A. [Department of Structure and Constituents of Matter, University of Barcelona (UB) Marti i Franques 1, 08028 Barcelona (Spain); Alonso, O. [Department of Electronics, University of Barcelona (UB) Marti i Franques 1, 08028 Barcelona (Spain); Gascon, D. [Department of Structure and Constituents of Matter, University of Barcelona (UB) Marti i Franques 1, 08028 Barcelona (Spain); Dieguez, A. [Department of Electronics, University of Barcelona (UB) Marti i Franques 1, 08028 Barcelona (Spain)

    2012-12-11

    Avalanche photodiodes operated in the Geiger mode offer a high intrinsic gain as well as an excellent timing accuracy. These qualities make the sensor specially suitable for those applications where detectors with high sensitivity and low timing uncertainty are required. Moreover, they are compatible with standard CMOS technologies, allowing sensor and front-end electronics integration within the pixel cell. However, the sensor suffers from high levels of intrinsic noise, which may lead to erroneous results and limit the range of detectable signals. They also increase the amount of data that has to be stored. In this work, we present a pixel based on a Geiger-mode avalanche photodiode operated in the gated mode to reduce the probability to detect noise counts interfering with photon arrival events. The readout circuit is based on a two grounds scheme to enable low reverse bias overvoltages and consequently lessen the dark count rate. Experimental characterization of the fabricated pixel with the HV-AMS 0.35 {mu}m standard technology is also presented in this article.

  7. Single photon detection in a waveguide-coupled Ge-on-Si lateral avalanche photodiode.

    Science.gov (United States)

    Martinez, Nicholas J D; Gehl, Michael; Derose, Christopher T; Starbuck, Andrew L; Pomerene, Andrew T; Lentine, Anthony L; Trotter, Douglas C; Davids, Paul S

    2017-07-10

    We examine gated-Geiger mode operation of an integrated waveguide-coupled Ge-on-Si lateral avalanche photodiode (APD) and demonstrate single photon detection at low dark count for this mode of operation. Our integrated waveguide-coupled APD is fabricated using a selective epitaxial Ge-on-Si growth process resulting in a separate absorption and charge multiplication (SACM) design compatible with our silicon photonics platform. Single photon detection efficiency and dark count rate is measured as a function of temperature in order to understand and optimize performance characteristics in this device. We report single photon detection of 5.27% at 1310 nm and a dark count rate of 534 kHz at 80 K for a Ge-on-Si single photon avalanche diode. Dark count rate is the lowest for a Ge-on-Si single photon detector in this range of temperatures while maintaining competitive detection efficiency. A jitter of 105 ps was measured for this device.

  8. Noise Temperature Characteristics and Gain-control of Avalanche Photodiodes for Laser Radar

    Institute of Scientific and Technical Information of China (English)

    CAI Xi-ping; SHANG Hong-Bo; BAI Ji-yuan; YANG Shuang; WANG Li-na

    2008-01-01

    Avalanche photodiodes(APDs) are promising light sensors with high quantum efficiency and low noise. It has been extensively used in radiation detection, laser radar and other weak signal detection fields. Unlike other photodiodes, APD is a very sensitive light detector with very high internal gain. The basic theory shows that the gain of APD is related to the temperature. The internal gain fluctuates with the variation of temperature. Investigated was the influence of the variation of the gain induced by the fluctuation of temperature on the output from APD for a very weak laser pulse input in laser radar. An active reverse-biased voltage compensation method is used to stabilize the gain of APD. An APD model is setup to simulate the detection of light pulse signal. The avalanche process, various noises and temperature's effect are all included in the model. Our results show that for the detection of weak light signal such as in laser radar, even a very small fluctuation of temperature could cause a great effect on APD's gain. The results show that the signal-to-noise ratio of the APD's output could be improved effectively with the active gain-control system.

  9. Modeling of snow avalanches for protection measures designing

    Science.gov (United States)

    Turchaninova, Alla; Lazarev, Anton; Loginova, Ekaterina; Seliverstov, Yuri; Glazovskaya, Tatiana; Komarov, Anton

    2017-04-01

    Avalanche protection structures such as dams have to be designed using well known standard engineering procedures that differ in different countries. Our intent is to conduct a research on structural avalanche protection measures designing and their reliability assessment during the operation using numerical modeling. In the Khibini Mountains, Russia, several avalanche dams have been constructed at different times to protect settlements and mining. Compared with other mitigation structures dams are often less expensive to construct in mining regions. The main goal of our investigation was to test the capabilities of Swiss avalanche dynamics model RAMMS and Russian methods to simulate the interaction of avalanches with mitigation structures such as catching and reflecting dams as well as to reach the observed runout distances after the transition through a dam. We present the RAMMS back-calculation results of an artificially triggered and well-documented catastrophic avalanche occurred in the town of Kirovsk, Khibini Mountains in February 2016 that has unexpectedly passed through a system of two catching dams and took the lives of 3 victims. The estimated volume of an avalanche was approximately 120,000 m3. For the calculation we used a 5 m DEM including catching dams generated from field measurements in summer 2015. We simulated this avalanche (occurred below 1000 m.a.s.l.) in RAMMS having taken the friction parameters (µ and ζ) from the upper altitude limit (above 1500 m.a.s.l.) from the table recommended for Switzerland (implemented into RAMMS) according to the results of our previous research. RAMMS reproduced the observed avalanche behavior and runout distance. No information is available concerning the flow velocity; however, calculated values correspond in general to the values measured in this avalanche track before. We applied RAMMS using an option of adding structures to DEM (including a dam in GIS) in other to test other operating catching dams in

  10. Preparation of Super-Thin, Large-Area, Double-Sided Gold-Plated Mylar Film

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    Large-area multi-wire parallel plane avalanche counter (MWPPAC) is a kind of gas detector widely used in nuclear experiments. MWPPAC is composed of front-window film, X wires, anode film, Y wires and rear-window film, which is mostly utilized to measuring

  11. Characterization and Monte Carlo simulation of single ion Geiger mode avalanche diodes integrated with a quantum dot nanostructure

    Science.gov (United States)

    Sharma, Peter; Abraham, J. B. S.; Ten Eyck, G.; Childs, K. D.; Bielejec, E.; Carroll, M. S.

    Detection of single ion implantation within a nanostructure is necessary for the high yield fabrication of implanted donor-based quantum computing architectures. Single ion Geiger mode avalanche (SIGMA) diodes with a laterally integrated nanostructure capable of forming a quantum dot were fabricated and characterized using photon pulses. The detection efficiency of this design was measured as a function of wavelength, lateral position, and for varying delay times between the photon pulse and the overbias detection window. Monte Carlo simulations based only on the random diffusion of photo-generated carriers and the geometrical placement of the avalanche region agrees qualitatively with device characterization. Based on these results, SIGMA detection efficiency appears to be determined solely by the diffusion of photo-generated electron-hole pairs into a buried avalanche region. Device performance is then highly dependent on the uniformity of the underlying silicon substrate and the proximity of photo-generated carriers to the silicon-silicon dioxide interface, which are the most important limiting factors for reaching the single ion detection limit with SIGMA detectors. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under Contract DE-AC04-94AL85000.

  12. Detector Unit

    CERN Multimedia

    1960-01-01

    Original detector unit of the Instituut voor Kernfysisch Onderzoek (IKO) BOL project. This detector unit shows that silicon detectors for nuclear physics particle detection were already developed and in use in the 1960's in Amsterdam. Also the idea of putting 'strips' onto the silicon for high spatial resolution of a particle's impact on the detector were implemented in the BOL project which used 64 of these detector units. The IKO BOL project with its silicon particle detectors was designed, built and operated from 1965 to roughly 1977. Detector Unit of the BOL project: These detectors, notably the ‘checkerboard detector’, were developed during the years 1964-1968 in Amsterdam, The Netherlands, by the Natuurkundig Laboratorium of the N.V. Philips Gloeilampen Fabrieken. This was done in close collaboration with the Instituut voor Kernfysisch Onderzoek (IKO) where the read-out electronics for their use in the BOL Project was developed and produced.

  13. Skier triggering of backcountry avalanches with skilled route selection

    Science.gov (United States)

    Sinickas, Alexandra; Haegeli, Pascal; Jamieson, Bruce

    2015-04-01

    Jamieson (2009) provided numerical estimates for the baseline probabilities of triggering an avalanche by a backcountry skier making fresh tracks without skilled route selection as a function of the North American avalanche danger scale (i.e., hazard levels Low, Moderate, Considerable, High and Extreme). Using the results of an expert survey, he showed that triggering probabilities while skiing directly up, down or across a trigger zone without skilled route selection increase roughly by a factor of 10 with each step of the North American avalanche danger scale (i.e. hazard level). The objective of the present study is to examine the effect of skilled route selection on the relationship between triggering probability and hazard level. To assess the effect of skilled route selection on triggering probability by hazard level, we analysed avalanche hazard assessments as well as reports of skiing activity and triggering of avalanches from 11 Canadian helicopter and snowcat operations during two winters (2012-13 and 2013-14). These reports were submitted to the daily information exchange among Canadian avalanche safety operations, and reflect professional decision-making and route selection practices of guides leading groups of skiers. We selected all skier-controlled or accidentally triggered avalanches with a destructive size greater than size 1 according to the Canadian avalanche size classification, triggered by any member of a guided group (guide or guest). These operations forecast the avalanche hazard daily for each of three elevation bands: alpine, treeline and below treeline. In contrast to the 2009 study, an exposure was defined as a group skiing within any one of the three elevation bands, and consequently within a hazard rating, for the day (~4,300 ratings over two winters). For example, a group that skied below treeline (rated Moderate) and treeline (rated Considerable) in one day, would receive one count for exposure to Moderate hazard, and one count for

  14. Infrared detectors

    CERN Document Server

    Rogalski, Antonio

    2010-01-01

    This second edition is fully revised and reorganized, with new chapters concerning third generation and quantum dot detectors, THz detectors, cantilever and antenna coupled detectors, and information on radiometry and IR optics materials. Part IV concerning focal plane arrays is significantly expanded. This book, resembling an encyclopedia of IR detectors, is well illustrated and contains many original references … a really comprehensive book.-F. Sizov, Institute of Semiconductor Physics, National Academy of Sciences, Kiev, Ukraine

  15. Particle Identification: Time-of-Flight, Cherenkov and Transition Radiation Detectors - Particle Detectors and Detector Systems

    CERN Document Server

    Ullaland, O

    2011-01-01

    Particle Identification: Time-of-Flight, Cherenkov and Transition Radiation Detectors in 'Particle Detectors and Detector Systems', part of 'Landolt-Börnstein - Group I Elementary Particles, Nuclei and Atoms: Numerical Data and Functional Relationships in Science and Technology, Volume 21B1: Detectors for Particles and Radiation. Part 1: Principles and Methods'. This document is part of Part 1 'Principles and Methods' of Subvolume B 'Detectors for Particles and Radiation' of Volume 21 'Elementary Particles' of Landolt-Börnstein - Group I 'Elementary Particles, Nuclei and Atoms'. It contains the Section '3.3 Particle Identification: Time-of-Flight, Cherenkov and Transition Radiation Detectors' of Chapter '3 Particle Detectors and Detector Systems' with the content: 3.3 Particle Identification: Time-of-Flight, Cherenkov and Transition Radiation Detectors 3.3.1 Introduction 3.3.2 Time of Flight Measurements 3.3.2.1 Scintillator hodoscopes 3.3.2.2 Parallel plate ToF detectors 3.3.3 Cherenkov Radiation 3.3.3.1 ...

  16. Avalanches in a granular stick-slip experiment: detection using wavelets

    Science.gov (United States)

    Abed Zadeh, Aghil; Barés, Jonathan; Behringer, Robert P.

    2017-06-01

    Avalanches have been experimentally investigated in a wide range of physical systems from granular physics to friction. Here, we measure and detect avalanches in a 2D granular stick-slip experiment. We discuss the conventional way of signal processing for avalanche extraction and how statistics depend on several parameters that are chosen in the analysis process. Then, we introduce another way of detecting avalanches using wavelet transformations that can be applied in many other systems. We show that by using this method and measuring Lipschitz exponents, we can intelligently detect noise in a signal, which leads to a better avalanche extraction and more reliable avalanche statistics.

  17. First approximations in avalanche model validations using seismic information

    Science.gov (United States)

    Roig Lafon, Pere; Suriñach, Emma; Bartelt, Perry; Pérez-Guillén, Cristina; Tapia, Mar; Sovilla, Betty

    2017-04-01

    Avalanche dynamics modelling is an essential tool for snow hazard management. Scenario based numerical modelling provides quantitative arguments for decision-making. The software tool RAMMS (WSL Institute for Snow and Avalanche Research SLF) is one such tool, often used by government authorities and geotechnical offices. As avalanche models improve, the quality of the numerical results will depend increasingly on user experience on the specification of input (e.g. release and entrainment volumes, secondary releases, snow temperature and quality). New model developments must continue to be validated using real phenomena data, for improving performance and reliability. The avalanches group form University of Barcelona (RISKNAT - UB), has studied the seismic signals generated from avalanches since 1994. Presently, the group manages the seismic installation at SLF's Vallée de la Sionne experimental site (VDLS). At VDLS the recorded seismic signals can be correlated to other avalanche measurement techniques, including both advanced remote sensing methods (radars, videogrammetry) and obstacle based sensors (pressure, capacitance, optical sender-reflector barriers). This comparison between different measurement techniques allows the group to address the question if seismic analysis can be used alone, on more additional avalanche tracks, to gain insight and validate numerical avalanche dynamics models in different terrain conditions. In this study, we aim to add the seismic data as an external record of the phenomena, able to validate RAMMS models. The seismic sensors are considerable easy and cheaper to install than other physical measuring tools, and are able to record data from the phenomena in every atmospheric conditions (e.g. bad weather, low light, freezing make photography, and other kind of sensors not usable). With seismic signals, we record the temporal evolution of the inner and denser parts of the avalanche. We are able to recognize the approximate position

  18. A method to precisely identify the afterpulses when using the S9717 avalanche photodiode

    Energy Technology Data Exchange (ETDEWEB)

    Rusu, Alexandru, E-mail: alrusu@nipne.ro; Rusu, Lucian [“Horia Hulubei” National Institute for Physics and Nuclear Engineering, Reactorului Street, No. 34, City Măgurele, jud. Ilfov, POB 077125 (Romania)

    2015-12-07

    The detection ratio of an avalanche photodiode (APD) biased in Geiger-mode increases versus the excess voltage; the afterpulsing rate increases too. The last one can be reduced by inserting an artificial dead time and accepting a lower measuring top rate. So, in order to tune a single-photon detector system, it is necessary to exactly identify afterpulses and measure their rate; the experimental results are presented. When using the S9717 APD in Geiger-mode, the cathode to ground voltage waveform reveals the existence of a particular sequence of pulses: a usual one followed, within 1μs, by a least one appearing to have been generated for negative excess voltage values. All these characteristics are the signature of the afterpulsing generation. Based on this observation, we were able to precisely measure the afterpulsing rate.

  19. A method to precisely identify the afterpulses when using the S9717 avalanche photodiode

    Science.gov (United States)

    Rusu, Alexandru; Rusu, Lucian

    2015-12-01

    The detection ratio of an avalanche photodiode (APD) biased in Geiger-mode increases versus the excess voltage; the afterpulsing rate increases too. The last one can be reduced by inserting an artificial dead time and accepting a lower measuring top rate. So, in order to tune a single-photon detector system, it is necessary to exactly identify afterpulses and measure their rate; the experimental results are presented. When using the S9717 APD in Geiger-mode, the cathode to ground voltage waveform reveals the existence of a particular sequence of pulses: a usual one followed, within 1μs, by a least one appearing to have been generated for negative excess voltage values. All these characteristics are the signature of the afterpulsing generation. Based on this observation, we were able to precisely measure the afterpulsing rate.

  20. A laser ranging system operating at 1036 nm with Geiger-mode silicon avalanche photodiode

    Science.gov (United States)

    Wu, Guang; Ren, Min; Liang, Yan; Wang, Zhiyuan; Pan, Haifeng; Zeng, Heping

    2012-09-01

    We demonstrated a laser ranging experiment obtained with a Geiger-mode silicon avalanche photodiode (Si GAPD). The Surface-to-surface resolution of 15 cm was achieved with the technique of time-correlated single-photon counting. In the experiment, a mode-locked Yb-doped fiber laser at 1036 nm was applied, as the detection efficiency at 1036 nm of Si GAPDs is much higher than that at 1064nm which was widely applied in remote sensing. Due to the single-photon detector, the laser ranging system was able to measure the reflected photon pulses at single-photon level. We realized 32- m laser ranging experiment with a 135-mm diameter Newtonian telescope in daylight. And the system could measure the non-cooperated object longer than 11.3 km far away, which was tested through inserting the optical loss. It presented a potential for hundreds-of-kilometer laser ranging at low-light level.

  1. Performance of a Large Area Avalanche Photodiode in a Liquid Xenon Ionization and Scintillation Chamber

    CERN Document Server

    Ni, K; Day, D; Giboni, K L; Lopes, J A M; Majewski, P; Yamashita, M

    2005-01-01

    Scintillation light produced in liquid xenon (LXe) by alpha particles, electrons and gamma-rays was detected with a large area avalanche photodiode (LAAPD) immersed in the liquid. The alpha scintillation yield was measured as a function of applied electric field. We estimate the quantum efficiency of the LAAPD to be 45%. The best energy resolution from the light measurement at zero electric field is 7.5%(sigma) for 976 keV internal conversion electrons from Bi-207 and 2.6%(sigma) for 5.5 MeV alpha particles from Am-241. The detector used for these measurements was also operated as a gridded ionization chamber to measure the charge yield. We confirm that using a LAAPD in LXe does not introduce impurities which inhibit the drifting of free electrons.

  2. Avalanche outbreaks emerging in cooperative contagions

    Science.gov (United States)

    Cai, Weiran; Chen, Li; Ghanbarnejad, Fakhteh; Grassberger, Peter

    2015-11-01

    The spreading of contagions can exhibit a percolation transition, which separates transitory prevalence from outbreaks that reach a finite fraction of the population. Such transitions are commonly believed to be continuous, but empirical studies have shown more violent spreading modes when the participating agents are not limited to one type. Striking examples include the co-epidemic of the Spanish flu and pneumonia that occurred in 1918 (refs , ), and, more recently, the concurrent prevalence of HIV/AIDS and a host of diseases. It remains unclear to what extent an outbreak in the presence of interacting pathogens differs from that due to an ordinary single-agent process. Here we study a mechanistic model for understanding contagion processes involving inter-agent cooperation. Our stochastic simulations reveal the possible emergence of a massive avalanche-like outbreak right at the threshold, which is manifested as a discontinuous phase transition. Such an abrupt change arises only if the underlying network topology supports a bottleneck for cascaded mutual infections. Surprisingly, all these discontinuous transitions are accompanied by non-trivial critical behaviours, presenting a rare case of hybrid transition. The findings may imply the origin of catastrophic occurrences in many realistic systems, from co-epidemics to financial contagions.

  3. The structure of powder snow avalanches

    Science.gov (United States)

    Sovilla, Betty; McElwaine, Jim N.; Louge, Michel Y.

    2015-01-01

    Powder snow avalanches (PSAs) can be hundreds of metres high and descend at astonishing speeds. This review paints a composite picture of PSAs from data acquired at the Vallée de la Sionne test site in Switzerland, including time-histories of snow cover thickness from buried RADAR and, at several elevations on a pylon, impact pressures from load cells, air pressure, particle velocity from optical sensors, and cloud density and particle cluster size from capacitance probes. PSAs feature distinct flow regions with stratification in mean density. At the head, highly fluctuating impact pressures weaken with elevation, while vertical velocity profiles evolve rapidly along the flow, suggesting that surface snow layers of light, cold, cohesionless snow erupt into a turbulent, inhomogeneous, recirculating frontal cloud region. For hundreds of metres behind the head, cloud stratification sharpens with the deposition of suspended cloud particles, while a denser basal flow of increasing thickness forms as deeper, warmer and heavier parts of the weakened snow cover are entrained. Toward the tail, vertical velocity profiles are more uniform, impact pressures become lower and steadier as the flow becomes thinner, and snow pack entrainment is negligible.

  4. Granular avalanches down inclined and vibrated planes

    Science.gov (United States)

    Gaudel, Naïma; Kiesgen de Richter, Sébastien; Louvet, Nicolas; Jenny, Mathieu; Skali-Lami, Salaheddine

    2016-09-01

    In this article, we study granular avalanches when external mechanical vibrations are applied. We identify conditions of flow arrest and compare with the ones classically observed for nonvibrating granular flows down inclines [Phys. Fluids 11, 542 (1999), 10.1063/1.869928]. We propose an empirical law to describe the thickness of the deposits with the inclination angle and the vibration intensity. The link between the surface velocity and the depth of the flow highlights a competition between gravity and vibrations induced flows. We identify two distinct regimes: (a) gravity-driven flows at large angles where vibrations do not modify dynamical properties but the deposits (scaling laws in this regime are in agreement with the literature for nonvibrating granular flows) and (b) vibrations-driven flows at small angles where no flow is possible without applied vibrations (in this last regime, the flow behavior can be properly described by a vibration induced activated process). We show, in this study, that granular flows down inclined planes can be finely tuned by external mechanical vibrations.

  5. Infrasonic monitoring of snow avalanches in the Alps

    Science.gov (United States)

    Marchetti, E.; Ulivieri, G.; Ripepe, M.; Chiambretti, I.; Segor, V.

    2012-04-01

    Risk assessment of snow avalanches is mostly related to weather conditions and snow cover. However a robust risk validation requires to identify all avalanches occurring, in order to compare predictions to real effects. For this purpose on December 2010 we installed a permanent 4-element, small aperture (100 m), infrasound array in the Alps, after a pilot experiment carried out in Gressonay during the 2009-2010 winter season. The array has been deployed in the Ayas Valley, at an elevation of 2000 m a.s.l., where natural avalanches are expected and controlled events are regularly performed. The array consists into 4 Optimic 2180 infrasonic microphones, with a sensitivity of 10-3 Pa in the 0.5-50 Hz frequency band and a 4 channel Guralp CMG-DM24 A/D converter, sampling at 100 Hz. Timing is achieved with a GPS receiver. Data are transmitted to the Department of Earth Sciences of the University of Firenze, where data is recorded and processed in real-time. A multi-channel semblance is carried out on the continuous data set as a function of slowness, back-azimuth and frequency of recorded infrasound in order to detect all avalanches occurring from the back-ground signal, strongly affected by microbarom and mountain induced gravity waves. This permanent installation in Italy will allow to verify the efficiency of the system in short-to-medium range (2-8 km) avalanche detection, and might represent an important validation to model avalanches activity during this winter season. Moreover, the real-time processing of infrasonic array data, might strongly contribute to avalanche risk assessments providing an up-to-description of ongoing events.

  6. Avalanches in a stochastic model of spiking neurons.

    Directory of Open Access Journals (Sweden)

    Marc Benayoun

    Full Text Available Neuronal avalanches are a form of spontaneous activity widely observed in cortical slices and other types of nervous tissue, both in vivo and in vitro. They are characterized by irregular, isolated population bursts when many neurons fire together, where the number of spikes per burst obeys a power law distribution. We simulate, using the Gillespie algorithm, a model of neuronal avalanches based on stochastic single neurons. The network consists of excitatory and inhibitory neurons, first with all-to-all connectivity and later with random sparse connectivity. Analyzing our model using the system size expansion, we show that the model obeys the standard Wilson-Cowan equations for large network sizes ( neurons. When excitation and inhibition are closely balanced, networks of thousands of neurons exhibit irregular synchronous activity, including the characteristic power law distribution of avalanche size. We show that these avalanches are due to the balanced network having weakly stable functionally feedforward dynamics, which amplifies some small fluctuations into the large population bursts. Balanced networks are thought to underlie a variety of observed network behaviours and have useful computational properties, such as responding quickly to changes in input. Thus, the appearance of avalanches in such functionally feedforward networks indicates that avalanches may be a simple consequence of a widely present network structure, when neuron dynamics are noisy. An important implication is that a network need not be "critical" for the production of avalanches, so experimentally observed power laws in burst size may be a signature of noisy functionally feedforward structure rather than of, for example, self-organized criticality.

  7. Avalanches in a stochastic model of spiking neurons.

    Science.gov (United States)

    Benayoun, Marc; Cowan, Jack D; van Drongelen, Wim; Wallace, Edward

    2010-07-08

    Neuronal avalanches are a form of spontaneous activity widely observed in cortical slices and other types of nervous tissue, both in vivo and in vitro. They are characterized by irregular, isolated population bursts when many neurons fire together, where the number of spikes per burst obeys a power law distribution. We simulate, using the Gillespie algorithm, a model of neuronal avalanches based on stochastic single neurons. The network consists of excitatory and inhibitory neurons, first with all-to-all connectivity and later with random sparse connectivity. Analyzing our model using the system size expansion, we show that the model obeys the standard Wilson-Cowan equations for large network sizes ( neurons). When excitation and inhibition are closely balanced, networks of thousands of neurons exhibit irregular synchronous activity, including the characteristic power law distribution of avalanche size. We show that these avalanches are due to the balanced network having weakly stable functionally feedforward dynamics, which amplifies some small fluctuations into the large population bursts. Balanced networks are thought to underlie a variety of observed network behaviours and have useful computational properties, such as responding quickly to changes in input. Thus, the appearance of avalanches in such functionally feedforward networks indicates that avalanches may be a simple consequence of a widely present network structure, when neuron dynamics are noisy. An important implication is that a network need not be "critical" for the production of avalanches, so experimentally observed power laws in burst size may be a signature of noisy functionally feedforward structure rather than of, for example, self-organized criticality.

  8. Gaseous Detectors: Charged Particle Detectors - Particle Detectors and Detector Systems

    CERN Document Server

    Hilke, H J

    2011-01-01

    Gaseous Detectors in 'Charged Particle Detectors - Particle Detectors and Detector Systems', part of 'Landolt-Börnstein - Group I Elementary Particles, Nuclei and Atoms: Numerical Data and Functional Relationships in Science and Technology, Volume 21B1: Detectors for Particles and Radiation. Part 1: Principles and Methods'. This document is part of Part 1 'Principles and Methods' of Subvolume B 'Detectors for Particles and Radiation' of Volume 21 'Elementary Particles' of Landolt-Börnstein - Group I 'Elementary Particles, Nuclei and Atoms'. It contains the Subsection '3.1.2 Gaseous Detectors' of Section '3.1 Charged Particle Detectors' of Chapter '3 Particle Detectors and Detector Systems' with the content: 3.1.2 Gaseous Detectors 3.1.2.1 Introduction 3.1.2.2 Basic Processes 3.1.2.2.1 Gas ionization by charged particles 3.1.2.2.1.1 Primary clusters 3.1.2.2.1.2 Cluster size distribution 3.1.2.2.1.3 Total number of ion pairs 3.1.2.2.1.4 Dependence of energy deposit on particle velocity 3.1.2.2.2 Transport of...

  9. Integrated electronics for time-resolved array of single-photon avalanche diodes

    Science.gov (United States)

    Acconcia, G.; Crotti, M.; Rech, I.; Ghioni, M.

    2013-12-01

    The Time Correlated Single Photon Counting (TCSPC) technique has reached a prominent position among analytical methods employed in a great variety of fields, from medicine and biology (fluorescence spectroscopy) to telemetry (laser ranging) and communication (quantum cryptography). Nevertheless the development of TCSPC acquisition systems featuring both a high number of parallel channels and very high performance is still an open challenge: to satisfy the tight requirements set by the applications, a fully parallel acquisition system requires not only high efficiency single photon detectors but also a read-out electronics specifically designed to obtain the highest performance in conjunction with these sensors. To this aim three main blocks have been designed: a gigahertz bandwidth front-end stage to directly read the custom technology SPAD array avalanche current, a reconfigurable logic to route the detectors output signals to the acquisition chain and an array of time measurement circuits capable of recording the photon arrival times with picoseconds time resolution and a very high linearity. An innovative architecture based on these three circuits will feature a very high number of detectors to perform a truly parallel spatial or spectral analysis and a smaller number of high performance time-to-amplitude converter offering very high performance and a very high conversion frequency while limiting the area occupation and power dissipation. The routing logic will make the dynamic connection between the two arrays possible in order to guarantee that no information gets lost.

  10. Understanding avalanches in a Micromegas from single-electron response measurement

    Energy Technology Data Exchange (ETDEWEB)

    Zerguerras, T., E-mail: zerguer@ipno.in2p3.fr [Institut de Physique Nucléaire (UMR 8608), CNRS/IN2P3-Université Paris-Sud, F-91406 Orsay Cedex (France); Genolini, B. [Institut de Physique Nucléaire (UMR 8608), CNRS/IN2P3-Université Paris-Sud, F-91406 Orsay Cedex (France); Kuger, F. [University of Würzburg, 97070 Würzburg (Germany); CERN, Geneva (Switzerland); Josselin, M.; Maroni, A.; Nguyen-Trung, T.; Pouthas, J.; Rosier, P. [Institut de Physique Nucléaire (UMR 8608), CNRS/IN2P3-Université Paris-Sud, F-91406 Orsay Cedex (France); Şahin, Ö. [Department of Physics, Uludağ University, 16059 Bursa (Turkey); Suzuki, D. [Institut de Physique Nucléaire (UMR 8608), CNRS/IN2P3-Université Paris-Sud, F-91406 Orsay Cedex (France); Veenhof, R. [Department of Physics, Uludağ University, 16059 Bursa (Turkey); RD51 Collaboration, CERN, Geneva (Switzerland)

    2015-02-01

    Avalanche fluctuations set a limit to the energy and position resolutions that can be reached by gaseous detectors. This paper presents a method based on a laser test-bench to measure the absolute gain and the relative gain variance of a Micro-Pattern Gaseous Detector from its single-electron response. A Micromegas detector was operated with three binary gas mixtures, composed of 5% isobutane as a quencher, with argon, neon or helium, at atmospheric pressure. The anode signals were read out by low-noise, high-gain Cremat CR-110 charge preamplifiers to enable single-electron detection down to gain of 5× 10{sup 3} for the first time. The argon mixture shows the lowest gain at a given amplification field together with the lowest breakdown limit, which is at a gain of 2×10{sup 4} an order of magnitude lower than that of neon or helium. For each gas, the relative gain variance f is almost unchanged in the range of amplification field studied. It was found that f is twice higher (f∼0.6) in argon than in the two other mixtures. This hierarchy of gain and relative gain variance agrees with predictions of analytic models, based on gas ionisation yields, and a Monte-Carlo model included in the simulation software Magboltz version 10.1.

  11. Positive operator-valued measure reconstruction of a beam-splitter tree-based photon-number-resolving detector.

    Science.gov (United States)

    Piacentini, F; Levi, M P; Avella, A; López, M; Kück, S; Polyakov, S V; Degiovanni, I P; Brida, G; Genovese, M

    2015-04-01

    Here we present a reconstruction of the positive operator-value measurement of a photon-number-resolving detector comprised of three 50∶50 beam-splitters in a tree configuration, terminated with four single-photon avalanche detectors. The four detectors' outputs are processed by an electronic board that discriminates detected photon number states from 0 to 4 and implements a "smart counting" routine to compensate for dead time issues at high count rates.

  12. Sediment Transport by Spring Avalanches in the Southern Swiss Alps

    Science.gov (United States)

    Egloff, J. M.; Hunziker, M.; Moore, J. R.; Christen, M.

    2010-12-01

    Dense wet-snow avalanches breaking through to the base of the snow pack or overriding snow-free surfaces can entrain basal material and act as important agents of sediment transport in steep Alpine catchments. As part of an ongoing study, we investigated two debris fans in the Matter Valley of southern Switzerland during spring 2009 and 2010, with emphasis on quantifying avalanche sediment transport. Deposited debris ranged from soil parcels and plant material to cobbles and boulders greater than 1 m3. Large boulders were generally angular and fresh with clear signs of recent impacts. The seasonal sediment load transported by avalanches was estimated at one fan by sampling the debris content within a number of representative areas, and then extrapolating the cumulative volume. Results reveal a total transported sediment volume of ~150 m3 in 2009 and ~15 m3 in 2010, which likely reflects varying snowfall and avalanche frequency between years. When distributed over the deposition area on the fan, these results imply an average accumulated sediment thickness of 12 mm in 2009 and 3 mm in 2010. Calculated catchment-wide erosion rates are ~0.1 mm/yr for 2009 and ~0.01 mm/yr for 2010. Cross-sections through avalanche debris revealed that transported sediment generally resides on top of the snow surface. As the avalanches melt, entrained sediment is set down gently, often resulting in precariously balanced boulders and rows of blocks perched on the walls of the fan’s channels. In flat lying areas, snowmelt resulted in sparse sediment deposits with no clear structure or sorting. Observations show that the fan surface is usually protected from erosion by snow and older avalanche deposits, which provide a smooth gliding plane for new events. Within the bedrock gulley adjacent to the fan, and in the avalanche source region above, signs of abrasive wear were evident on exposed bedrock surfaces. These include rounded and scoured bedrock, fresh signs of boulder impacts, and

  13. Implications of Grainfall for Avalanches and Barchan Dune Morphodynamics

    Science.gov (United States)

    Nield, J. M.; Wiggs, G.; Baddock, M. C.; Hipondoka, M.

    2016-12-01

    Sediment accumulation on aeolian dunes is predominately though avalanching (or grainflow). This grainflow is initiated by the accumulation of grainfall deposits, close to the dune brink. When the accumulation, or `bulge', exceeds an angle of repose, avalanches are initiated and sediment is transported down the lee of the dune. The location of sediment accumulation, or avalanche initiation point, is determined by the distance that grainfall can travel from the dune brink. While previous studies have focused on determining angles at which avalanches occur, along with depositional flux rates, technical constraints have limited the testing of models to predict grainfall zone dynamics under varying wind conditions. Here we use terrestrial laser scanning (TLS) to measure both grainfall distance and associated lee slope surface change of a 5 m high barchan dune under variable wind speeds, on the Skeleton Coast, Namibia. We find that under stronger winds, the distance that grainfall can travel from the brink expands (by up to 0.45 m for a 3 m/s increase in wind speed). Along with this expansion of the grainfall distance there is an increase in saltation flux over the brink. The increased grainfall distance shifts sand further from the brink resulting in dominant avalanche initiation point locations expanding from 0.3 m to 0.4 m for wind speeds above 6 m/s. This shift also corresponds to the appearance of secondary avalanches, which are initiated by primary avalanche lobe deposits extending outside of the main grainfall zone. Ultimately, under stronger winds the expansion of the grainfall distance contributes to the destabilisation and movement of increased sediment volumes down the lee slope. Avalanches under stronger wind speeds, therefore, increase in thickness, width and length, while during weaker wind speeds, most of the grainfall and grainflow is limited to the upper section of the lee slope. The implication of this dual avalanche behaviour under variable wind

  14. 3D integration of Geiger-mode avalanche photodiodes aimed to very high fill-factor pixels for future linear colliders

    Energy Technology Data Exchange (ETDEWEB)

    Vilella, E., E-mail: evilella@el.ub.edu; Alonso, O.; Diéguez, A.

    2013-12-11

    This paper presents an analysis of the maximum achievable fill-factor by a pixel detector of Geiger-mode avalanche photodiodes with the Chartered 130 nm/Tezzaron 3D process. The analysis shows that fill-factors between 66% and 96% can be obtained with different array architectures and a time-gated readout circuit of minimum area. The maximum fill-factor is achieved when the two-layer vertical stack is used to overlap the non-sensitive areas of one layer with the sensitive areas of the other one. Moreover, different sensor areas are used to further increase the fill-factor. A chip containing a pixel detector of the Geiger-mode avalanche photodiodes and aimed to future linear colliders has been designed with the Chartered 130 nm/Tezzaron 3D process to increase the fill-factor. -- Highlights: •GAPD pixel detectors present a low detection efficiency due to a reduced fill-factor. •3D-ICs are proposed as a solution to increase the fill-factor of GAPD detectors. •The maximum achievable fill-factor by a GAPD detector in a 3D-IC process is analyzed. •Fill-factors between 66% and 96% can be obtained with different array architectures. •The array is operated in a time-gated mode to reduce the expected sensor noise.

  15. Dynamics of the Bingham Canyon rock avalanches (Utah, USA) resolved from topographic, seismic, and infrasound data: Bingham Canyon Rock Avalanches

    Energy Technology Data Exchange (ETDEWEB)

    Moore, Jeffrey R. [Department of Geology and Geophysics, University of Utah, Salt Lake City Utah USA; Pankow, Kristine L. [Department of Geology and Geophysics, University of Utah, Salt Lake City Utah USA; Ford, Sean R. [Atmospheric, Earth, and Energy Division, Lawrence Livermore National Laboratory, Livermore California USA; Koper, Keith D. [Department of Geology and Geophysics, University of Utah, Salt Lake City Utah USA; Hale, J. Mark [Department of Geology and Geophysics, University of Utah, Salt Lake City Utah USA; Aaron, Jordan [Department of Earth, Ocean and Atmospheric Sciences, University of British Columbia, Vancouver British Columbia Canada; Larsen, Chris F. [Geophysical Institute, University of Alaska Fairbanks, Fairbanks Alaska USA

    2017-03-01

    The 2013 Bingham Canyon Mine rock avalanches represent one of the largest cumulative landslide events in recorded U.S. history and provide a unique opportunity to test remote analysis techniques for landslide characterization. Here we combine aerial photogrammetry surveying, topographic reconstruction, numerical runout modeling, and analysis of broadband seismic and infrasound data to extract salient details of the dynamics and evolution of the multiphase landslide event. Our results reveal a cumulative intact rock source volume of 52 Mm3, which mobilized in two main rock avalanche phases separated by 1.5 h. We estimate that the first rock avalanche had 1.5–2 times greater volume than the second. Each failure initiated by sliding along a gently dipping (21°), highly persistent basal fault before transitioning to a rock avalanche and spilling into the inner pit. The trajectory and duration of the two rock avalanches were reconstructed using runout modeling and independent force history inversion of intermediate-period (10–50 s) seismic data. Intermediate- and shorter-period (1–50 s) seismic data were sensitive to intervals of mass redirection and constrained finer details of the individual slide dynamics. Back projecting short-period (0.2–1 s) seismic energy, we located the two rock avalanches within 2 and 4 km of the mine. Further analysis of infrasound and seismic data revealed that the cumulative event included an additional 11 smaller landslides (volumes ~104–105 m3) and that a trailing signal following the second rock avalanche may result from an air-coupled Rayleigh wave. Our results demonstrate new and refined techniques for detailed remote characterization of the dynamics and evolution of large landslides.

  16. Snow avalanche friction relation based on extended kinetic theory

    Science.gov (United States)

    Rauter, Matthias; Fischer, Jan-Thomas; Fellin, Wolfgang; Kofler, Andreas

    2016-11-01

    Rheological models for granular materials play an important role in the numerical simulation of dry dense snow avalanches. This article describes the application of a physically based model from the field of kinetic theory to snow avalanche simulations. The fundamental structure of the so-called extended kinetic theory is outlined and the decisive model behavior for avalanches is identified. A simplified relation, covering the basic features of the extended kinetic theory, is developed and implemented into an operational avalanche simulation software. To test the obtained friction relation, simulation results are compared to velocity and runout observations of avalanches, recorded from different field tests. As reference we utilize a classic phenomenological friction relation, which is commonly applied for hazard estimation. The quantitative comparison is based on the combination of normalized residuals of different observation variables in order to take into account the quality of the simulations in various regards. It is demonstrated that the extended kinetic theory provides a physically based explanation for the structure of phenomenological friction relations. The friction relation derived with the help of the extended kinetic theory shows advantages to the classic phenomenological friction, in particular when different events and various observation variables are investigated.

  17. Solitary granular avalanches: stability, fingering and theoretical modeling

    Science.gov (United States)

    Malloggi, Florent; Andreotti, Bruno; Clément, Eric; Aronson, Igor; Tsimring, Lev

    2008-03-01

    Avalanching processes do not only occur in the air as we know of snow avalanches, mud flows and land-slides. Such events frequently happen below the see level as they take many forms from turbidity currents to thick sediment waves. In this study we report results on laboratory scale avalanche experiments taking place both in the air and under-water. In both cases a family of stable solitary erosion/deposition waves is observed [1]. At higher inclination angles, we show the existence of a long wavelength transverse instability followed by a coarsening and the onset of a fingering pattern. While the experiments strongly differ by the spatial and time scales, the agreement between the stability diagrams, the wavelengths selection and the avalanche morphology suggest a common erosion/deposition scenario. We also use these erosion/deposition waves to investigate the dynamics of granular flow and jamming in the frame work of the Partial Fluidization Theory (PFT) proposed by Aronson et al. to describe the dynamics of granular matter near jamming [2]. [1] F. Malloggi et al. Europhysics Letters, 2006, Erosion waves: Transverse instabilities and fingering 75, 825-831 [2] I. S. Aranson et al.. Transverse instability of avalanches in granular flows down an incline. Physical Review E, 2006, 73, 050302; I.S.Aronson et al., Non rheological properties of granular flows: exploring the near jamming limit, preprint (2007).

  18. Infrasound monitoring of snow avalanches in the Italian Alps

    Science.gov (United States)

    Ripepe, Maurizio; Ulivieri, Giacomo; Marchetti, Emanuele; Chiambretti, Igor; Segor, Valerio; Pitet, Luca

    2010-05-01

    Risk assessment of snow avalanches is mostly related to weather conditions and snow cover. However a robust risk validation requires to identify all avalanches occurring, in order to compare predictions to real effects. For this purpose on December 2009 we installed a temporary 4-element, small aperture (100 m), infrasound array in the Alps. The array has been deployed south of Mt. Rosa, at an elevation of 2000 m a.s.l. in the valley of Gressoney, where natural avalanches are expected and triggered ones are regularly programmed. The array consists into 4 absolute pressure transducers with a sensitivity of 0.01 Pa in the 0.1-50 Hz frequency band and a 7 channel Guralp CMG-DM24 A/D converter, sampling at 100 Hz. Timing is achieved with a GPS receiver. The array is completely buried in snow. Gel cell batteries and 200 W solar panels provide the array power requirements (~3 W) and should allow a continuous operation during the winter season. A multi-channel semblance is carried out on the continuous data set as a function of slowness, back-azimuth and frequency of recorded infrasound in order to detect all avalanches occurring from the back-ground signal, strongly affected by microbarom and mountain induced gravity waves. This pilot experiment in Italy will allow to verify the efficiency of the system, and might represent an important validation to modeled avalanches activity during this winter season.

  19. The effectiveness of mean-field theory for avalanche distributions

    Science.gov (United States)

    Lee, Edward; Raju, Archishman; Sethna, James

    We explore the mean-field theory of the pseudogap found in avalanche systems with long-range anisotropic interactions using analytical and numerical tools. The pseudogap in the density of low-stability states emerges from the competition between stabilizing interactions between spins in an avalanche and the destabilizing random movement towards the threshold caused by anisotropic couplings. Pazmandi et al. have shown that for the Sherrington-Kirkpatrick model, the pseudogap scales linearly and produces a distribution of avalanche sizes with exponent t=1 in contrast with that predicted from RFIM t=3/2. Lin et al. have argued that the scaling exponent ? of the pseudogap depends on the tail of the distribution of couplings and on non-universal values like the strain rate and the magnitude of the coupling strength. Yet others have argued that the relationship between the pseudogap scaling and the distribution of avalanche sizes is dependent on dynamical details. Despite the theoretical arguments, the class of RFIM mean-field models is surprisingly good at predicting the distribution of avalanche sizes in a variety of different magnetic systems. We investigate these differences with a combination of theory and simulation.

  20. Segregation induced fingering instabilities in granular avalanches

    Science.gov (United States)

    Woodhouse, Mark; Thornton, Anthony; Johnson, Chris; Kokelaar, Pete; Gray, Nico

    2013-04-01

    It is important to be able to predict the distance to which a hazardous natural granular flows (e.g. snow slab avalanches, debris-flows and pyroclastic flows) might travel, as this information is vital for accurate assessment of the risks posed by such events. In the high solids fraction regions of these flows the large particles commonly segregate to the surface, where they are transported to the margins to form bouldery flow fronts. In many natural flows these bouldery margins experience a much greater frictional force, leading to frontal instabilities. These instabilities create levees that channelize the flow vastly increasing the run-out distance. A similar effect can be observed in dry granular experiments, which use a combination of small round and large rough particles. When this mixture is poured down an inclined plane, particle size segregation causes the large particles to accumulate near the margins. Being rougher, the large particles experience a greater friction force and this configuration (rougher material in front of smoother) can be unstable. The instability causes the uniform flow front to break up into a series of fingers. A recent model for particle size-segregation has been coupled to existing avalanche models through a particle concentration dependent friction law. In this talk numerical solutions of this coupled system are presented and compared to both large scale experiments carried out at the USGS flume and more controlled small scale laboratory experiments. The coupled depth-averaged model captures the accumulation of large particles at the flow front. We show this large particle accumulation at the head of the flow can lead to the break-up of the initially uniform front into a series of fingers. However, we are unable to obtain a fully grid-resolved numerical solution; the width of the fingers decreases as the grid is refined. By considering the linear stability of a steady, fully-developed, bidisperse granular layer it is shown that