WorldWideScience

Sample records for plastics packaging materials

  1. Plasticizers effect on native biodegradable package materials

    Science.gov (United States)

    Cozar, Onuc; Cioica, Nicolae; Coţa, Constantin; Nagy, Elena Mihaela; Fechete, Radu

    2017-01-01

    Changes in intensity of some IR and Raman bands suggest the plasticizing - antiplasticizing effects of water and glycerol contents and a small increase of amorphous/crystalline ratio, too. The nuclear magnetic relaxation data show that the amorphous/crystalline ratio depends on amylose/amylopectin mobility and also by the place of their polymer chain segments. Thus the distributions of spin-spin (T2) relaxation times and the shift toward higher values of some T2 characteristic peaks show that the increasing of water and glycerol content in the starch package materials lead to the more mobile amylose and amylopectin polymer chain segments and the prevalence of amorphous regions in the prepared native corn starch samples.

  2. GREEN PLASTIC: A NEW PLASTIC FOR PACKAGING

    OpenAIRE

    Mr. Pankaj Kumar*, Sonia

    2016-01-01

    This paper gives a brief idea about a new type of plastic called as bio-plastic or green plastic. Plastic is used as a packaging material for various products, but this plastic is made up of non renewable raw materials. There are various disadvantages of using conventional plastic like littering, CO2 production, non-degradable in nature etc. To overcome these problems a new type of plastic is discovered called bio-plastic or green plastic. Bio-plastic is made from renewable resources and also...

  3. Plastic packaging materials and environmental problems. Plastic hosozai to kankyo mondai

    Energy Technology Data Exchange (ETDEWEB)

    Uemura, T. (Sekisui Plastics Co. Ltd., Osaka (Japan))

    1992-05-01

    This paper describes the recent trends in the environmental problems created from used plastic packaging materials. The 23 wards of the city of Tokyo produce refuses daily of 12,000 tons (1990), with plastics accounting for 15% by volume. Discussions to deal with plastic refuses that are bulky and standing out began as early as in 1971 when the disposal study meeting was inaugurated. As a result, wastes from polyvinyl chloride sheet for agricultural green houses had 40% recovered and recycled out of 100,000 tons generated annually, and styrofoam wastes at 10% of 150,000 tons. The wastes disposal law and the recycling law were established in 1991 aiming at reducing volume of wastes, promoting re-utilization, and assuring appropriate disposal methods and facilities. The Wastes Re-utilization Association was organized to handle styrofoam wastes that are attracting strong attention recently, the association having begun its activities with a good start. It is expected that styrofoam wastes will be molten thermally and regenerated into the same styrofoam products. Styrofoam could be more energy saving and resource saving material than paper cups. 6 refs., 10 figs., 5 tabs.

  4. Pyrolysis of plastic packaging waste: A comparison of plastic residuals from material recovery facilities with simulated plastic waste.

    Science.gov (United States)

    Adrados, A; de Marco, I; Caballero, B M; López, A; Laresgoiti, M F; Torres, A

    2012-05-01

    Pyrolysis may be an alternative for the reclamation of rejected streams of waste from sorting plants where packing and packaging plastic waste is separated and classified. These rejected streams consist of many different materials (e.g., polyethylene (PE), polypropylene (PP), polystyrene (PS), polyvinyl chloride (PVC), polyethylene terephthalate (PET), acrylonitrile butadiene styrene (ABS), aluminum, tetra-brik, and film) for which an attempt at complete separation is not technically possible or economically viable, and they are typically sent to landfills or incinerators. For this study, a simulated plastic mixture and a real waste sample from a sorting plant were pyrolyzed using a non-stirred semi-batch reactor. Red mud, a byproduct of the aluminum industry, was used as a catalyst. Despite the fact that the samples had a similar volume of material, there were noteworthy differences in the pyrolysis yields. The real waste sample resulted, after pyrolysis, in higher gas and solid yields and consequently produced less liquid. There were also significant differences noted in the compositions of the compared pyrolysis products.

  5. Rapid discrimination of plastic packaging materials using MIR spectroscopy coupled with independent components analysis (ICA)

    Energy Technology Data Exchange (ETDEWEB)

    Kassouf, Amine, E-mail: amine.kassouf@agroparistech.fr [ER004 “Lebanese Food Packaging”, Faculty of Sciences II, Lebanese University, 90656 Jdeideth El Matn, Fanar (Lebanon); INRA, UMR1145 Ingénierie Procédés Aliments, 1 Avenue des Olympiades, 91300 Massy (France); AgroParisTech, UMR1145 Ingénierie Procédés Aliments, 16 rue Claude Bernard, 75005 Paris (France); Maalouly, Jacqueline, E-mail: j_maalouly@hotmail.com [ER004 “Lebanese Food Packaging”, Faculty of Sciences II, Lebanese University, 90656 Jdeideth El Matn, Fanar (Lebanon); Rutledge, Douglas N., E-mail: douglas.rutledge@agroparistech.fr [INRA, UMR1145 Ingénierie Procédés Aliments, 1 Avenue des Olympiades, 91300 Massy (France); AgroParisTech, UMR1145 Ingénierie Procédés Aliments, 16 rue Claude Bernard, 75005 Paris (France); Chebib, Hanna, E-mail: hchebib@hotmail.com [ER004 “Lebanese Food Packaging”, Faculty of Sciences II, Lebanese University, 90656 Jdeideth El Matn, Fanar (Lebanon); Ducruet, Violette, E-mail: violette.ducruet@agroparistech.fr [INRA, UMR1145 Ingénierie Procédés Aliments, 1 Avenue des Olympiades, 91300 Massy (France); AgroParisTech, UMR1145 Ingénierie Procédés Aliments, 16 rue Claude Bernard, 75005 Paris (France)

    2014-11-15

    Highlights: • An innovative technique, MIR-ICA, was applied to plastic packaging separation. • This study was carried out on PE, PP, PS, PET and PLA plastic packaging materials. • ICA was applied to discriminate plastics and 100% separation rates were obtained. • Analyses performed on two spectrometers proved the reproducibility of the method. • MIR-ICA is a simple and fast technique allowing plastic identification/classification. - Abstract: Plastic packaging wastes increased considerably in recent decades, raising a major and serious public concern on political, economical and environmental levels. Dealing with this kind of problems is generally done by landfilling and energy recovery. However, these two methods are becoming more and more expensive, hazardous to the public health and the environment. Therefore, recycling is gaining worldwide consideration as a solution to decrease the growing volume of plastic packaging wastes and simultaneously reduce the consumption of oil required to produce virgin resin. Nevertheless, a major shortage is encountered in recycling which is related to the sorting of plastic wastes. In this paper, a feasibility study was performed in order to test the potential of an innovative approach combining mid infrared (MIR) spectroscopy with independent components analysis (ICA), as a simple and fast approach which could achieve high separation rates. This approach (MIR-ICA) gave 100% discrimination rates in the separation of all studied plastics: polyethylene terephthalate (PET), polyethylene (PE), polypropylene (PP), polystyrene (PS) and polylactide (PLA). In addition, some more specific discriminations were obtained separating plastic materials belonging to the same polymer family e.g. high density polyethylene (HDPE) from low density polyethylene (LDPE). High discrimination rates were obtained despite the heterogeneity among samples especially differences in colors, thicknesses and surface textures. The reproducibility of

  6. PROSPECTS OF POLYMER PACKAGING MATERIALS

    Directory of Open Access Journals (Sweden)

    V. A. Sedykh

    2012-01-01

    Full Text Available The main types of materials used in the manufacture of packaging. Analyzed trends in further development of packaging materials. Shows how to improve the quality of plastic packaging materials in today's market.

  7. Migration of nanoparticles from plastic packaging materials containing carbon black into foodstuffs.

    Science.gov (United States)

    Bott, Johannes; Störmer, Angela; Franz, Roland

    2014-01-01

    Carbon black was investigated to assess and quantify the possibility that nanoparticles might migrate out of plastic materials used in the food packaging industry. Two types of carbon black were incorporated in low-density polyethylene (LDPE) and polystyrene (PS) at 2.5% and 5.0% loading (w/w), and then subjected to migration studies. The samples were exposed to different food simulants according to European Union Plastics Regulation 10/2011, simulating long-term storage with aqueous and fatty foodstuffs. Asymmetric flow field-flow fractionation (AF4) coupled to a multi-angle laser light-scattering (MALLS) detector was used to separate, characterise and quantify the potential release of nanoparticles. The AF4 method was successful in differentiating carbon black from other matrix components, such as extracted polymer chains, in the migration solution. At a detection limit of 12 µg kg⁻¹, carbon black did not migrate from the packaging material into food simulants. The experimental findings are in agreement with theoretical considerations based on migration modelling. From both the experimental findings and theoretical considerations, it can be concluded that carbon black does not migrate into food once it is incorporated into a plastics food contact material.

  8. Rapid discrimination of plastic packaging materials using MIR spectroscopy coupled with independent components analysis (ICA).

    Science.gov (United States)

    Kassouf, Amine; Maalouly, Jacqueline; Rutledge, Douglas N; Chebib, Hanna; Ducruet, Violette

    2014-11-01

    Plastic packaging wastes increased considerably in recent decades, raising a major and serious public concern on political, economical and environmental levels. Dealing with this kind of problems is generally done by landfilling and energy recovery. However, these two methods are becoming more and more expensive, hazardous to the public health and the environment. Therefore, recycling is gaining worldwide consideration as a solution to decrease the growing volume of plastic packaging wastes and simultaneously reduce the consumption of oil required to produce virgin resin. Nevertheless, a major shortage is encountered in recycling which is related to the sorting of plastic wastes. In this paper, a feasibility study was performed in order to test the potential of an innovative approach combining mid infrared (MIR) spectroscopy with independent components analysis (ICA), as a simple and fast approach which could achieve high separation rates. This approach (MIR-ICA) gave 100% discrimination rates in the separation of all studied plastics: polyethylene terephthalate (PET), polyethylene (PE), polypropylene (PP), polystyrene (PS) and polylactide (PLA). In addition, some more specific discriminations were obtained separating plastic materials belonging to the same polymer family e.g. high density polyethylene (HDPE) from low density polyethylene (LDPE). High discrimination rates were obtained despite the heterogeneity among samples especially differences in colors, thicknesses and surface textures. The reproducibility of the proposed approach was also tested using two spectrometers with considerable differences in their sensitivities. Discrimination rates were not affected proving that the developed approach could be extrapolated to different spectrometers. MIR combined with ICA is a promising tool for plastic waste separation that can help improve performance in this field; however further technological improvements and developments are required before it can be applied

  9. Quality and safety aspects of reusable plastic food packaging materials : influence of reuse on intrinsic properties

    NARCIS (Netherlands)

    Jetten, J.; Kruijf, N. de

    2002-01-01

    The aim of the project was to develop a comprehensive package of quality assurance criteria for use by the industry and by regulatory authorities to ensure the quality and safety-in-use (sensory, microbiological and chemical safety) of reused plastics for food packaging. The paper describes the

  10. Quality and safety aspects of reusable plastic food packaging materials : influence of reuse on intrinsic properties

    NARCIS (Netherlands)

    Jetten, J.; Kruijf, N. de

    2002-01-01

    The aim of the project was to develop a comprehensive package of quality assurance criteria for use by the industry and by regulatory authorities to ensure the quality and safety-in-use (sensory, microbiological and chemical safety) of reused plastics for food packaging. The paper describes the inve

  11. Quality and safety aspects of reusable plastic food packaging materials: influence of reuse on intrinsic properties.

    Science.gov (United States)

    Jetten, J; de, Kruijf N

    2002-01-01

    The aim of the project was to develop a comprehensive package of quality assurance criteria for use by the industry and by regulatory authorities to ensure the quality and safety-in-use (sensory, microbiological and chemical safety) of reused plastics for food packaging. The paper describes the investigations into potential adulteration effects by reuse on the intrinsic properties of plastics in more detail. The plastic articles investigated were bottles of polyethylene terephthalate (PET) or polycarbonate (PC) and vending cups of polypropylene (PP). The influence of repeated use on the migration of plastic constituents, degradation products of plastic additives, barrier properties and surface characteristics were investigated. The overall conclusion was that the investigated intrinsic properties of the refillable articles were not significantly influenced by repeated use. Only the hydrophobicity of the refillable PC and PP articles seemed to be influenced by repeated washing. PC bottles washed 15 times were significantly less hydrophobic than unwashed bottles.

  12. Life Cycle Assessment of Common Plastic Packaging for Reducing Environmental Impact and Material Consumption

    Directory of Open Access Journals (Sweden)

    Visvaldas Varžinskas

    2009-12-01

    the Faculty of Design and Technologies, Kaunas University of Technology, together with packaging and environmental protection specialists of the University, and in cooperation with the Department of Printed Publications and Packaging of the Ukrainian Print Academy. The present paper analyses certain basic findings of the study on the possibilities of improving the ecological level of packaging within the framework of the project. It is stated that appropriate investigation of packaging, its production and application has to be performed in order to prove that the packaging was produced in compliance with preventive and other principles; this investigation is related to a wide variety of package testing, some of which has not yet got methodology acknowledged at a sufficient level (the EU or groups of countries. Therefore, one of the research directions in the above mentioned project, discussed in the present paper, is related to developing a single system, recognized throughout the EU, which would enable researchers to perform the required tests confirming the packaging quality compliance with the environmental requirements. The paper analyzes the EU prevention regulations for reducing the amount of raw material and the system of checking the realization of the requirements based on identification of critical areas, aimed at reaching the lowest possible package weight and/or volume, consequently, the minimum waste amount, without increasing the amount of faulty products and product waste. The paper presents the findings of the research obtained in assessing the life cycle, when applying the Ecoindicator'99 qualitative analysis, concerning the impact of common plastic packages and processes on the environment during manufacturing, usage and disposal. Compression test results of common type plastic packaging construction are presented, which allow us to assess the impact of the package shape and construction upon the packaging reliability and minimization of its mass.

  13. Greenhouse gas emissions from the treatment of household plastic containers and packaging: replacement with biomass-based materials.

    Science.gov (United States)

    Yano, Junya; Hirai, Yasuhiro; Sakai, Shin-ichi; Tsubota, Jun

    2014-04-01

    The purpose of this study was to quantify the life-cycle greenhouse gas (GHG) emissions reduction that could be achieved by replacement of fossil-derived materials with biodegradable, biomass-based materials for household plastic containers and packaging, considering a variety of their treatment options. The biomass-based materials were 100% polylactide or a combination of polybutylene succinate adipate and polylactide. A scenario analysis was conducted considering alternative recycling methods. Five scenarios were considered: two for existing fossil-derived materials (the current approach in Japan) and the three for biomass-based materials. Production and waste disposal of 1 m(3) of plastic containers and packaging from households was defined as the functional unit. The results showed that replacement of fossil-derived materials with biomass-based materials could reduce life-cycle GHG emissions by 14-20%. Source separation and recycling should be promoted. When the separate collection ratio reached 100%, replacement with biomass-based materials could potentially reduce GHG emissions by 31.9%. Food containers are a priority for replacement, because they alone could reduce GHG emissions by 10%. A recycling system for biomass-based plastics must be carefully designed, considering aspects such as the transition period from fossil-derived plastics to biomass-based plastics.

  14. Greenhouse gas emissions from the treatment of household plastic containers and packaging: replacement with biomass-based materials.

    OpenAIRE

    Yano, Junya; Hirai, Yasuhiro; Sakai, Shin-ichi; Tsubota, Jun

    2014-01-01

    The purpose of this study was to quantify the life-cycle greenhouse gas (GHG) emissions reduction that could be achieved by replacement of fossil-derived materials with biodegradable, biomass-based materials for household plastic containers and packaging, considering a variety of their treatment options. The biomass-based materials were 100% polylactide or a combination of polybutylene succinate adipate and polylactide. A scenario analysis was conducted considering alternative recycling metho...

  15. Microelectronics plastic molded packaging

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, D.R. [Ktech Corp., Albuquerque, NM (United States); Palmer, D.W.; Peterson, D.W. [Sandia National Lab., Albuquerque, NM (United States)] [and others

    1997-02-01

    The use of commercial off-the-shelf (COTS) microelectronics for nuclear weapon applications will soon be reality rather than hearsay. The use of COTS for new technologies for uniquely military applications is being driven by the so-called Perry Initiative that requires the U.S. Department of Defense (DoD) to accept and utilize commercial standards for procurement of military systems. Based on this philosophy, coupled with several practical considerations, new weapons systems as well as future upgrades will contain plastic encapsulated microelectronics. However, a conservative Department of Energy (DOE) approach requires lifetime predictive models. Thus, the focus of the current project is on accelerated testing to advance current aging models as well as on the development of the methodology to be used during WR qualification of plastic encapsulated microelectronics. An additional focal point involves achieving awareness of commercial capabilities, materials, and processes. One of the major outcomes of the project has been the definition of proper techniques for handling and evaluation of modern surface mount parts which might be used in future systems. This program is also raising the familiarity level of plastic within the weapons complex, allowing subsystem design rules accommodating COTS to evolve. A two year program plan is presented along with test results and commercial interactions during this first year.

  16. Plastic food packaging and health

    Directory of Open Access Journals (Sweden)

    Raika Durusoy

    2011-02-01

    Full Text Available Plastics have a wide usage in our daily lives. One of their uses is for food packaging and food containers. The aim of this review is to introduce different types of chemicals that can leach from food packaging plastics into foods and cause human exposure and to mention their effects on health. The types of plastics were reviewed under the 13 headings in Turkish Codex Alimentarius and plastics recycling symbols were provided to enable the recognition of the type of plastic when applicable. Chemicals used during the production and that can cause health risks are investigated under the heading of the relevant type of plastic. The most important chemicals from plastic food packaging that can cause toxicity are styrene, 1,3-butadiene, melamine, formaldehyde, acrylamide, di-2-ethylhexyl phthalate, di-2-ethylhexyl adipate, vinyl chloride and bisphenol A. These chemicals have endocrine disrupting, carcinogenic and/or development disrupting effects. These chemicals may leach into foods depending on the chemical properties of the plastic or food, temperature during packaging, processing and storage, exposure to UV and duration of storage. Contact with fatty/oily or acidic foods, heating of the food inside the container, or drinking hot drinks from plastic cups, use of old and scratched plastics and some detergents increase the risk of leaching. The use of plastic containers and packaging for food and beveradges should be avoided whenever possible and when necessary, less harmful types of plastic should be preferred. [TAF Prev Med Bull 2011; 10(1.000: 87-96

  17. Quality and safety aspects of reusable plastic food packaging materials : a European study to underpin future legislation

    NARCIS (Netherlands)

    Jetten, J.; Kruijf, N. de; Castle, L.

    1999-01-01

    The objective of this study was to develop a comprehensive package of quality assurance criteria for use by industry and regulatory authorities for ensuring the quality and safety-in-use (sensory, microbiological and chemical) of reused plastics for food packaging. The study included thermal

  18. Quality and safety aspects of reusable plastic food packaging materials : a European study to underpin future legislation

    NARCIS (Netherlands)

    Jetten, J.; Kruijf, N. de; Castle, L.

    1999-01-01

    The objective of this study was to develop a comprehensive package of quality assurance criteria for use by industry and regulatory authorities for ensuring the quality and safety-in-use (sensory, microbiological and chemical) of reused plastics for food packaging. The study included thermal degrada

  19. Toward 6 log10 pulsed electric field inactivation with conductive plastic packaging material

    NARCIS (Netherlands)

    Roodenburg, B.; Haan, S.W.H. de; Ferreira, J.A.; Coronel, P.; Wouters, P.C.; Hatt, V.

    2013-01-01

    Generally, high grade products such as pulsed electric field (PEF) treated fruit juices are packaged after their preservative treatment. However, PEF treatment after packaging could avoid recontamination of the product and becomes feasible when electric field pulses of sufficient magnitude can be ge

  20. Toward 6 log10 pulsed electric field inactivation with conductive plastic packaging material

    NARCIS (Netherlands)

    Roodenburg, B.; Haan, S.W.H. de; Ferreira, J.A.; Coronel, P.; Wouters, P.C.; Hatt, V.

    2013-01-01

    Generally, high grade products such as pulsed electric field (PEF) treated fruit juices are packaged after their preservative treatment. However, PEF treatment after packaging could avoid recontamination of the product and becomes feasible when electric field pulses of sufficient magnitude can be

  1. Extension of the sorting instructions for household plastic packaging and changes in exposure to bioaerosols at materials recovery facilities.

    Science.gov (United States)

    Schlosser, O; Déportes, I Z; Facon, B; Fromont, E

    2015-12-01

    The aim of this study was to assess how extending the sorting instructions for plastic packaging would affect the exposure of workers working at materials recovery facility (MRF) to dust, endotoxins, fungi and bacteria, taking into consideration other factors that could have an influence on this exposure. Personal sampling was carried out at four MRFs during six sampling campaigns at each facility, both in sorting rooms and when the workers were involved in "mobile tasks" away from the rooms. The data was analysed by describing the extension of sorting instructions both using a qualitative variable (after vs before) and using data for the pots and trays recycling stream, including or excluding plastic film. Overall, before the extension of the sorting guidelines, the geometric mean of personal exposure levels in sorting rooms was 0.3mg/m(3) for dust, 27.7 EU/m(3) for endotoxins, 13,000 CFU/m(3) for fungi and 1800 CFU/m(3) for bacteria. When workers were involved in mobile tasks away from the rooms, these averages were 0.5mg/m(3), 25.7 EU/m(3), 28,000 CFU/m(3) and 5100 CFU/m(3) respectively.The application by households of instructions to include pots, trays and film with other recyclable plastic packaging led to an increase in exposure to endotoxins, fungi and bacteria at MRFs. For an increase of 0.5 kg per inhabitant per year in the pots, trays and film recycling stream, exposure in sorting rooms rose by a factor of 1.4-2.2, depending on the biological agent. Exposure during mobile tasks increased by a factor of 3.0-3.6. The age of the waste amplified the effect of the extension of sorting instructions on exposure to fungi, bacteria and endotoxins. Factors that had a significant influence on the exposure of workers to dust and/or bioaerosols included the presence of paper, newspapers and magazines in the sorted waste, the order in which incoming waste was treated and the quality of the ventilation system in the sorting rooms. The levels of exposure observed in

  2. Influence of storage Time and Temperature on Absorption of Flavour Compounds from Solutions by Plastic Packaging Materials

    NARCIS (Netherlands)

    Willige, R.; Schoolmeester, D.; Ooij, van A.; Linssen, J.P.H.; Voragen, A.G.J.

    2002-01-01

    Food packaging, although an integral part of the food chain, has a major drawback in that, often, the packaging material interacts with the flavor constituents of the food, causing either a selective or an extensive loss of desirable food flavors or absorption of undesirable off-flavors from the

  3. Materials for advanced packaging

    CERN Document Server

    Wong, CP

    2008-01-01

    Significant progress has been made in advanced packaging in recent years. Several new packaging techniques have been developed and new packaging materials have been introduced. This book provides a comprehensive overview of the recent developments in this industry, particularly in the areas of microelectronics, optoelectronics, digital health, and bio-medical applications. The book discusses established techniques, as well as emerging technologies, in order to provide readers with the most up-to-date developments in advanced packaging.

  4. Edible packaging materials.

    Science.gov (United States)

    Janjarasskul, Theeranun; Krochta, John M

    2010-01-01

    Research groups and the food and pharmaceutical industries recognize edible packaging as a useful alternative or addition to conventional packaging to reduce waste and to create novel applications for improving product stability, quality, safety, variety, and convenience for consumers. Recent studies have explored the ability of biopolymer-based food packaging materials to carry and control-release active compounds. As diverse edible packaging materials derived from various by-products or waste from food industry are being developed, the dry thermoplastic process is advancing rapidly as a feasible commercial edible packaging manufacturing process. The employment of nanocomposite concepts to edible packaging materials promises to improve barrier and mechanical properties and facilitate effective incorporation of bioactive ingredients and other designed functions. In addition to the need for a more fundamental understanding to enable design to desired specifications, edible packaging has to overcome challenges such as regulatory requirements, consumer acceptance, and scaling-up research concepts to commercial applications.

  5. 75 FR 5375 - Hazardous Material; Miscellaneous Packaging Amendments

    Science.gov (United States)

    2010-02-02

    ... plastic bags, plastic film bags, textile bags, and paper bags. The purpose was to eliminate uncertainty in... in This Final Rule A. Definitions B. Plastic Packagings Used To Transport Poison Materials C... provisions to require plastic single and composite non-bulk packagings containing Division 6.1 material to...

  6. [Determination of 46 plasticizers in food contact polyvinyl chloride packaging materials and their migration into food simulants by gas chromatography-mass spectrometry].

    Science.gov (United States)

    Guo, Chunhai; Bo, Haibo; Duan, Wenzhong; Jia, Haitao; Chen, Ruichun; Ma, Yusong; Ai, Lianfeng

    2011-01-01

    A gas chromatography-mass spectrometry (GC-MS) method was developed for the determination of 46 plasticizers in food contact polyvinyl chloride (PVC) packaging materials and their migration into food simulants, i. e. water, 3% acetic acid, 10% ethanol and olive oil. Plasticizers in the PVC packaging materials, aqueous food simulants and olive oil food simulants were extracted by the dissolution-precipitation, liquid-liquid extraction and gel permeation chromatography (GPC) approaches, respectively. The extracts were analyzed by GC-MS in selective ion monitoring (SIM) mode and quantified using the external standard method. The cal-ibration curves were linear in the ranges of 0.1-2.0 mg/L with the correlation coefficients of 0.9910-0. 999 9. The limits of detection were from 0. 005 mg/kg to 0. 05 mg/kg ( S/N = 5 ). The recoveries at 3 spiked levels were 69.51%-107. 21% and the relative standard deviations (RSDs n = 6) ranged from 3.53% to 18.95%. These results show that this method is fast, sensitive and accurate for the qualitative and quantitative determination of plasticizers in food contact plastic products and 4 types of food simulants.

  7. Materials for advanced packaging

    CERN Document Server

    Wong, CP

    2017-01-01

    This second edition continues to be the most comprehensive review on the developments in advanced electronic packaging technologies, with a focus on materials and processing. Recognized experts in the field contribute to 22 updated and new chapters that provide comprehensive coverage on various 3D package architectures, novel bonding and joining techniques, wire bonding, wafer thinning techniques, organic substrates, and novel approaches to make electrical interconnects between integrated circuit and substrates. Various chapters also address advances in several key packaging materials, including: Lead-free solders Flip chip underfills Epoxy molding compounds Conductive adhesives Die attach adhesives/films Thermal interface materials (TIMS) Materials for fabricating embedded passives including capacitors, inductors, and resistors Materials and processing aspects on wafer-level chip scale package (CSP) and MicroElectroMechanical system (MEMS) Contributors also review new and emerging technologies such as Light ...

  8. Nutritional response of Okra to various packaging materials and ...

    African Journals Online (AJOL)

    Nutritional response of Okra to various packaging materials and chemical pickling agents. ... AFRICAN JOURNALS ONLINE (AJOL) · Journals · Advanced Search ... and groundnut oil) and packaging materials (glass jar, plastic and stainless ...

  9. 国内外塑料包装材料回收法律体系概况%The Overview of Legal System about Recycling Plastic Packaging Material at Home and Abroad

    Institute of Scientific and Technical Information of China (English)

    张玉霞; 张岩; 李东萱; 俞婧; 王洪涛

    2011-01-01

    介绍了中国和欧、美、日等发达国家塑料包装材料同收立法现状,其中包括同收塑料用于食品包装的概况.塑料包装T业要实现可持续发展,当务之急是加快包装材料回收立法,尤其是食品塑料包装回收立法工作.%This article described the legislative status of recycling of plastic packaging materials in China, Europe, America and Japan, including recycled plastics for food packaging profiles. To achieve sustainable development of plastic packaging industry, it is imperative to speed up packaging recycling legislation, in particular for food plastic packaging recycling legislation.

  10. Taking plastics packaging to the future through improving barrier properties

    CSIR Research Space (South Africa)

    Labuschagne, Philip W

    2011-11-01

    Full Text Available the Manufacturing and Materials Industry in it quest for global competitiveness CSIR Manufacturing and Materials Technology Permeability Thermodynamic component of gas transport = solubility coefficient, S (in mol m-3 Pa-1) Kinetic component of gas transport... the Manufacturing and Materials Industry in its quest for global competitiveness orting the Manufacturing and Materials Industry in it quest for global competitiveness CSIR Manufacturing and Materials Technology Taking Plastics Packaging to the Future Through...

  11. 49 CFR Appendix B to Part 173 - Procedure for Testing Chemical Compatibility and Rate of Permeation in Plastic Packaging and...

    Science.gov (United States)

    2010-10-01

    ... Rate of Permeation in Plastic Packaging and Receptacles B Appendix B to Part 173 Transportation Other... Plastic Packaging and Receptacles 1. The purpose of this procedure is to determine the chemical compatibility and permeability of liquid hazardous materials packaged in plastic packaging and...

  12. Packaging - Materials review

    Science.gov (United States)

    Herrmann, Matthias

    2014-06-01

    Nowadays, a large number of different electrochemical energy storage systems are known. In the last two decades the development was strongly driven by a continuously growing market of portable electronic devices (e.g. cellular phones, lap top computers, camcorders, cameras, tools). Current intensive efforts are under way to develop systems for automotive industry within the framework of electrically propelled mobility (e.g. hybrid electric vehicles, plug-in hybrid electric vehicles, full electric vehicles) and also for the energy storage market (e.g. electrical grid stability, renewable energies). Besides the different systems (cell chemistries), electrochemical cells and batteries were developed and are offered in many shapes, sizes and designs, in order to meet performance and design requirements of the widespread applications. Proper packaging is thereby one important technological step for designing optimum, reliable and safe batteries for operation. In this contribution, current packaging approaches of cells and batteries together with the corresponding materials are discussed. The focus is laid on rechargeable systems for industrial applications (i.e. alkaline systems, lithium-ion, lead-acid). In principle, four different cell types (shapes) can be identified - button, cylindrical, prismatic and pouch. Cell size can be either in accordance with international (e.g. International Electrotechnical Commission, IEC) or other standards or can meet application-specific dimensions. Since cell housing or container, terminals and, if necessary, safety installations as inactive (non-reactive) materials reduce energy density of the battery, the development of low-weight packages is a challenging task. In addition to that, other requirements have to be fulfilled: mechanical stability and durability, sealing (e.g. high permeation barrier against humidity for lithium-ion technology), high packing efficiency, possible installation of safety devices (current interrupt device

  13. Packaging - Materials review

    Energy Technology Data Exchange (ETDEWEB)

    Herrmann, Matthias [Hoppecke Advanced Battery Technology GmbH, 08056 Zwickau (Germany)

    2014-06-16

    Nowadays, a large number of different electrochemical energy storage systems are known. In the last two decades the development was strongly driven by a continuously growing market of portable electronic devices (e.g. cellular phones, lap top computers, camcorders, cameras, tools). Current intensive efforts are under way to develop systems for automotive industry within the framework of electrically propelled mobility (e.g. hybrid electric vehicles, plug-in hybrid electric vehicles, full electric vehicles) and also for the energy storage market (e.g. electrical grid stability, renewable energies). Besides the different systems (cell chemistries), electrochemical cells and batteries were developed and are offered in many shapes, sizes and designs, in order to meet performance and design requirements of the widespread applications. Proper packaging is thereby one important technological step for designing optimum, reliable and safe batteries for operation. In this contribution, current packaging approaches of cells and batteries together with the corresponding materials are discussed. The focus is laid on rechargeable systems for industrial applications (i.e. alkaline systems, lithium-ion, lead-acid). In principle, four different cell types (shapes) can be identified - button, cylindrical, prismatic and pouch. Cell size can be either in accordance with international (e.g. International Electrotechnical Commission, IEC) or other standards or can meet application-specific dimensions. Since cell housing or container, terminals and, if necessary, safety installations as inactive (non-reactive) materials reduce energy density of the battery, the development of low-weight packages is a challenging task. In addition to that, other requirements have to be fulfilled: mechanical stability and durability, sealing (e.g. high permeation barrier against humidity for lithium-ion technology), high packing efficiency, possible installation of safety devices (current interrupt device

  14. Scenarios study on post-consumer plastic packaging waste recycling

    NARCIS (Netherlands)

    Thoden van Velzen, E.U.; Bos-Brouwers, H.E.J.; Groot, J.J.; Bing Xiaoyun, Xiaoyun; Jansen, M.; Luijsterburg, B.

    2013-01-01

    We all use plastics on a daily basis. Plastics come in many shapes, sizes and compositions and are used in a wide variety of products. Almost all of the currently used plastic packaging are made from fossil resources, which are finite. The production of plastic packages causes environmental impacts,

  15. Scenarios study on post-consumer plastic packaging waste recycling

    NARCIS (Netherlands)

    Thoden van Velzen, E.U.; Bos-Brouwers, H.E.J.; Groot, J.J.; Bing Xiaoyun, Xiaoyun; Jansen, M.; Luijsterburg, B.

    2013-01-01

    We all use plastics on a daily basis. Plastics come in many shapes, sizes and compositions and are used in a wide variety of products. Almost all of the currently used plastic packaging are made from fossil resources, which are finite. The production of plastic packages causes environmental impacts,

  16. Determination of Thirteen Plasticizers in Food Plastic Packaging Materials by Capillary Column Gas Chromatography%食品包装材料中13种增塑剂的毛细管气相色谱法测定

    Institute of Scientific and Technical Information of China (English)

    马康; 汤福寿; 何雅娟; 刘菲

    2011-01-01

    A capillary column gas chromatographic method was developed for the separation and determination of thirteen plasticizers, including dimethyl phthalate acid ester(DMP), diethyl phthalate acid ester( DEP), dipropyl phthalate acid ester( DnPP), diisobutyl phthalate acid ester( DIBP), dibutyl phthalate acid ester( DBP), diamyl phthalate acid ester( DAP), bisphenol A( BIA), di-n-hexyl phthalate acid ester(DHP), butyl benzyl phthalate acid ester(BBP), di-2-ethylhexyl adipate (DEHA), di(2-ethylhexyl) phthalate acid ester(DEHP), dioctyl phthalate acid ester(DOP) and dinonyl phthalate acid ester(DNP) in plastic packaging materials for foodstuff. The analytes were extracted with hexane from samples by Soxhlet extraction technique, then purified by silica solid phase extraction. Three key factors such as rinse solvent, eluting solvent and eluting volume were optimized. Hexane and toluene ( 1: 1, by volume) were used as rinse solvents, 2 mL ethyl acetate was used as eluting solvent. After filtration, the eluate was determined by gas chromatography with flame ionization detector(GC/FID). The calibration curves of thirteen plasticizers were linear in the range of O. 1 - 1 000 mg/L with detection limits of 0. 005 - 0. 030 mg/L. The spiked recoveries ranged from 90% to 116% with relative standard deviations of 2. 2% -4. 9%. The method was successfully applied in the determination of plasticizers in plastic packaging materials for foodstuff.%建立了索氏提取、固相萃取净化浓缩、毛细管气相色谱法测定塑料食品包装材料中13种增塑剂的方法.优化了固相萃取淋洗剂、洗脱剂和洗脱剂体积等参数.样品经正己烷索氏提取后,用硅胶小柱净化浓缩.以正己烷-甲苯为淋洗剂,2 mL乙酸乙酯为洗脱剂.过滤后的洗脱液用气相色谱仪分析.结果显示,13种增塑剂在0.1~1000 mg/L范围内呈良好线性,检出限为0.005~O.030 mg/L.样品的加标回收率为90%~116%,相对标准偏差为2.2%~4.9%.

  17. 食品塑料包装材料中邻苯二甲酸二(2-乙基己)酯的暴露评估%Exposure Assessment of Di(2-ethylhexyl)phthalate of Plastic Food Packaging Materials

    Institute of Scientific and Technical Information of China (English)

    白艳红; 许珂; 赵电波

    2012-01-01

    This article mainly reviewed the nature, source, toxicity and hazard of di(2-ethylhexyl)phthalate, one of the phthalate plasticizers of food plastics packaging materials. Preventive measures and proposals for this reference were discussed to provide security for plastic food packaging materials, as well as for packed food security research.%文中主要综述了食品塑料包装材料所用邻苯二甲酸酯类增塑剂中,邻苯二甲酸二(2.乙基己)酯(DEHP)的性质、来源、毒性及危害.提出了预防措施和建议,为食品塑料包装材料的安全性以及包装食品的安全性的相关研究提供参考依据.

  18. Influence of RFID tags on recyclability of plastic packaging.

    Science.gov (United States)

    Aliaga, César; Ferreira, Beatriz; Hortal, Mercedes; Pancorbo, María Ángeles; López, José Manuel; Navas, Francisco Javier

    2011-06-01

    The use of Radio Frequency IDentification Technology (RFID) in the packaging sector is an important logistical improvement regarding the advantages offered by this technology in comparison with barcodes. Nevertheless, the presence of these devices in plastic packaging, and consequently in plastic waste, can cause several problems in the recycling plants due to the materials included in these devices. In this study, the mentioned recycling constraints have been experimentally identified in a pilot scale recycling study consisting in three recycling tests with an increasing presence of RFID tags. Differences in each test were evaluated. Furthermore, the quality of the recycled material of each test was studied through the injection and testing of tests probes. The results of the pilot scale recycling tests did not show a decrease in the quality of the recycled plastic due to the presence of RFID tags. Nevertheless, several operational problems during the recycling process were observed such as the obstruction of the screens, which lessened the process yield and created process interruptions, as well as the loss of extruded plastic during the process. These recycling constraints cannot be directly extrapolated to the industrial plants due to the different working scales. Nevertheless, technological solutions are proposed in order to avoid these recycling constraints if they appear.

  19. Compostability of bioplastic packaging materials: an overview.

    Science.gov (United States)

    Kale, Gaurav; Kijchavengkul, Thitisilp; Auras, Rafael; Rubino, Maria; Selke, Susan E; Singh, Sher Paul

    2007-03-08

    Packaging waste accounted for 78.81 million tons or 31.6% of the total municipal solid waste (MSW) in 2003 in the USA, 56.3 million tons or 25% of the MSW in 2005 in Europe, and 3.3 million tons or 10% of the MSW in 2004 in Australia. Currently, in the USA the dominant method of packaging waste disposal is landfill, followed by recycling, incineration, and composting. Since landfill occupies valuable space and results in the generation of greenhouse gases and contaminants, recovery methods such as reuse, recycling and/or composting are encouraged as a way of reducing packaging waste disposal. Most of the common materials used in packaging (i.e., steel, aluminum, glass, paper, paperboard, plastics, and wood) can be efficiently recovered by recycling; however, if packaging materials are soiled with foods or other biological substances, physical recycling of these materials may be impractical. Therefore, composting some of these packaging materials is a promising way to reduce MSW. As biopolymers are developed and increasingly used in applications such as food, pharmaceutical, and consumer goods packaging, composting could become one of the prevailing methods for disposal of packaging waste provided that industry, governments, and consumers encourage and embrace this alternative. The main objective of this article is to provide an overview of the current situation of packaging compostability, to describe the main mechanisms that make a biopolymer compostable, to delineate the main methods to compost these biomaterials, and to explain the main standards for assessing compostability, and the current status of biopolymer labeling. Biopolymers such as polylactide and poly(hydroxybutyrate) are increasingly becoming available for use in food, medical, and consumer goods packaging applications. The main claims of these new biomaterials are that they are obtained from renewable resources and that they can be biodegraded in biological environments such as soil and compost

  20. 19 CFR 191.13 - Packaging materials.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 2 2010-04-01 2010-04-01 false Packaging materials. 191.13 Section 191.13 Customs... (CONTINUED) DRAWBACK General Provisions § 191.13 Packaging materials. (a) Imported packaging material... packaging material when used to package or repackage merchandise or articles exported or destroyed pursuant...

  1. Characterization of integrated circuit packaging materials

    CERN Document Server

    Moore, Thomas

    1993-01-01

    Chapters in this volume address important characteristics of IC packages. Analytical techniques appropriate for IC package characterization are demonstrated through examples of the measurement of critical performance parameters and the analysis of key technological problems of IC packages. Issues are discussed which affect a variety of package types, including plastic surface-mount packages, hermetic packages, and advanced designs such as flip-chip, chip-on-board and multi-chip models.

  2. Recyclability assessment of nano-reinforced plastic packaging

    Energy Technology Data Exchange (ETDEWEB)

    Sánchez, C., E-mail: csanchez@itene.com [Sustainability Divison, Packaging, Transport and Logistics Research Institute, Albert Einstein 1, 46980 Paterna, Valencia (Spain); Hortal, M., E-mail: mhortal@itene.com [Sustainability Divison, Packaging, Transport and Logistics Research Institute, Albert Einstein 1, 46980 Paterna, Valencia (Spain); Aliaga, C., E-mail: caliaga@itene.com [Sustainability Divison, Packaging, Transport and Logistics Research Institute, Albert Einstein 1, 46980 Paterna, Valencia (Spain); Devis, A., E-mail: adevis@itene.com [Sustainability Divison, Packaging, Transport and Logistics Research Institute, Albert Einstein 1, 46980 Paterna, Valencia (Spain); Cloquell-Ballester, V.A., E-mail: cloquell@dpi.upv.es [Dpto. Proyectos de Ingeniería, Universitat Politècnica de València, Camino de Vera, 46022 Valencia (Spain)

    2014-12-15

    Highlights: • The study compares the recyclability of polymers with and without nanoparticles. • Visual appearance, material quality and mechanical properties are evaluated. • Minor variations in mechanical properties in R-PE and R-PP with nanoparticles. • Slight degradation of R-PET which affect mechanical properties. • Colour deviations in recycled PE, PP and PET in ranges higher that 0.3 units. - Abstract: Packaging is expected to become the leading application for nano-composites by 2020 due to the great advantages on mechanical and active properties achieved with these substances. As novel materials, and although there are some current applications in the market, there is still unknown areas under development. One key issue to be addressed is to know more about the implications of the nano-composite packaging materials once they become waste. The present study evaluates the extrusion process of four nanomaterials (Layered silicate modified nanoclay (Nanoclay1), Calcium Carbonate (CaCO{sub 3}), Silver (Ag) and Zinc Oxide (ZnO) as part of different virgin polymer matrices of polyethylene (PE), Polypropylene (PP) and Polyethyleneterephtalate (PET). Thus, the following film plastic materials: (PE–Nanoclay1, PE–CaCO{sub 3}, PP–Ag, PET–ZnO, PET–Ag, PET–Nanoclay1) have been processed considering different recycling scenarios. Results on recyclability show that for PE and PP, in general terms and except for some minor variations in yellowness index, tensile modulus, tensile strength and tear strength (PE with Nanoclay1, PP with Ag), the introduction of nanomaterial in the recycling streams for plastic films does not affect the final recycled plastic material in terms of mechanical properties and material quality compared to conventional recycled plastic. Regarding PET, results show that the increasing addition of nanomaterial into the recycled PET matrix (especially PET–Ag) could influence important properties of the recycled material, due to a

  3. Characterisation of plastic packaging waste for recycling: problems related to current approaches

    DEFF Research Database (Denmark)

    Götze, Ramona; Astrup, Thomas Fruergaard

    2013-01-01

    were addressed by a resin type-based sorting analysis and a washing test for plastic packaging material from Danish household waste. Preliminary results show that, for a quarter of the hand sorted material, no resin type could be identified and that Polypropylene and Polyethylene terephthalate were...... criteria of recycling processes. A lack of information in current waste characterisation practise on polymer resin composition, black coloured material content and the influence of surface adherent material on physico-chemical characteristics of plastic packaging waste were identified. These shortcomings...... the dominating resin types in plastic packaging. The suggested washing procedure caused a decrease of 70% of the ash content of the plastic material. The analysed metals and nutrients were reduced by up to 24%...

  4. Optimizing biomass blends for manufacturing molded packaging materials using mycelium

    Science.gov (United States)

    Polystyrene is one of the most widely used plastics and is commonly produced in three forms: 1) Extruded polystyrene – disposable utensils, CD/DVD cases, yogurt containers, smoke alarm housing, etc.; 2) Expanded polystyrene foam – molded packaging materials and packaging "peanuts"; 3) Extruded polys...

  5. Recyclability assessment of nano-reinforced plastic packaging.

    Science.gov (United States)

    Sánchez, C; Hortal, M; Aliaga, C; Devis, A; Cloquell-Ballester, V A

    2014-12-01

    Packaging is expected to become the leading application for nano-composites by 2020 due to the great advantages on mechanical and active properties achieved with these substances. As novel materials, and although there are some current applications in the market, there is still unknown areas under development. One key issue to be addressed is to know more about the implications of the nano-composite packaging materials once they become waste. The present study evaluates the extrusion process of four nanomaterials (Layered silicate modified nanoclay (Nanoclay1), Calcium Carbonate (CaCO3), Silver (Ag) and Zinc Oxide (ZnO) as part of different virgin polymer matrices of polyethylene (PE), Polypropylene (PP) and Polyethyleneterephtalate (PET). Thus, the following film plastic materials: (PE-Nanoclay1, PE-CaCO3, PP-Ag, PET-ZnO, PET-Ag, PET-Nanoclay1) have been processed considering different recycling scenarios. Results on recyclability show that for PE and PP, in general terms and except for some minor variations in yellowness index, tensile modulus, tensile strength and tear strength (PE with Nanoclay1, PP with Ag), the introduction of nanomaterial in the recycling streams for plastic films does not affect the final recycled plastic material in terms of mechanical properties and material quality compared to conventional recycled plastic. Regarding PET, results show that the increasing addition of nanomaterial into the recycled PET matrix (especially PET-Ag) could influence important properties of the recycled material, due to a slight degradation of the polymer, such as increasing pinholes, degradation fumes and elongation at break. Moreover, it should be noted that colour deviations were visible in most of the samples (PE, PP and PET) in levels higher than 0.3 units (limit perceivable by the human eye). The acceptance of these changes in the properties of recycled PE, PP and PET will depend on the specific applications considered (e.g. packaging applications are more

  6. Hazardous Material Packaging and Transportation

    Energy Technology Data Exchange (ETDEWEB)

    Hypes, Philip A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-02-04

    This is a student training course. Some course objectives are to: recognize and use standard international and US customary units to describe activities and exposure rates associated with radioactive material; determine whether a quantity of a single radionuclide meets the definition of a class 7 (radioactive) material; determine, for a given single radionuclide, the shipping quantity activity limits per 49 Code of Federal Regulations (CFR) 173.435; determine the appropriate radioactive material hazard class proper shipping name for a given material; determine when a single radionuclide meets the DOT definition of a hazardous substance; determine the appropriate packaging required for a given radioactive material; identify the markings to be placed on a package of radioactive material; determine the label(s) to apply to a given radioactive material package; identify the entry requirements for radioactive material labels; determine the proper placement for radioactive material label(s); identify the shipping paper entry requirements for radioactive material; select the appropriate placards for a given radioactive material shipment or vehicle load; and identify allowable transport limits and unacceptable transport conditions for radioactive material.

  7. Polylactide nanocomposites for packaging materials: A review

    Science.gov (United States)

    Widiastuti, Indah

    2016-02-01

    This review aims at highlighting on an attempt for improving the properties of polylactide (PLA) as packaging material by application of nanocomposite technology. PLA is attracting considerable interest because of more eco-friendliness from its origin as contrast to the petrochemical-based polymers and its biodegradability. Despite possessing good mechanical and optical properties, deterioration of the material properties in PLA materials during their service time could occur after prolonged exposure to humidity and high temperature condition. Limited gas barrier is another drawback of PLA material that should be overcome to satisfy the requirement for packaging application. To further extend the range of mechanical and thermal properties achievable, several attempts have been made in modifying the material such as blending with other polymers, use of plasticizing material and development of PLA nanocomposites. Nanocomposite is a fairly new type of composite that has emerged in which the reinforcing filler has nanometer scale dimensions (at least one dimension of the filler is less than 100 nm). In this review, the critical properties of PLA as packaging materials and its degradation mechanism are presented. This paper discusses the current effort and key research challenges in the development of nanocomposites based on biodegradable polymer matrices and nano-fillers. The PLA layered silicate nanocomposites where the filler platelets can be dispersed in the polymer at the nanometer scale owing to the specific filler surface modification, frequently exhibits remarkable improvements of mechanical strength, gas barrier and thermal stability.

  8. 9 CFR 381.144 - Packaging materials.

    Science.gov (United States)

    2010-01-01

    ... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Packaging materials. 381.144 Section... Packaging materials. (a) Edible products may not be packaged in a container which is composed in whole or in... to health. All packaging materials must be safe for the intended use within the meaning of section...

  9. Semiconductor packaging materials interaction and reliability

    CERN Document Server

    Chen, Andrea

    2012-01-01

    In semiconductor manufacturing, understanding how various materials behave and interact is critical to making a reliable and robust semiconductor package. Semiconductor Packaging: Materials Interaction and Reliability provides a fundamental understanding of the underlying physical properties of the materials used in a semiconductor package. The book focuses on an important step in semiconductor manufacturing--package assembly and testing. It covers the basics of material properties and explains how to determine which behaviors are important to package performance. The authors also discuss how

  10. Laser cutting plastic materials

    Energy Technology Data Exchange (ETDEWEB)

    Van Cleave, R.A.

    1980-08-01

    A 1000-watt CO/sub 2/ laser has been demonstrated as a reliable production machine tool for cutting of plastics, high strength reinforced composites, and other nonmetals. More than 40 different plastics have been laser cut, and the results are tabulated. Applications for laser cutting described include fiberglass-reinforced laminates, Kevlar/epoxy composites, fiberglass-reinforced phenolics, nylon/epoxy laminates, ceramics, and disposable tooling made from acrylic.

  11. 9 CFR 317.24 - Packaging materials.

    Science.gov (United States)

    2010-01-01

    ... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Packaging materials. 317.24 Section... INSPECTION AND CERTIFICATION LABELING, MARKING DEVICES, AND CONTAINERS General § 317.24 Packaging materials... packaging materials must be safe for their intended use within the meaning of section 409 of the Federal...

  12. Disposability Characteristics of Military Packaging Materials

    Science.gov (United States)

    1974-03-06

    packaging material but repre- sents only a minor segment of all packaging materials. In terms of U. S. tonnage, wood packaging materials account for...motftontttctl Anotywu of Solid Hoof COMactwn. David H. Markt and Jon C. Uabman (of Jonnt Hopkint Univartity), for tha U.S. Dapartmant of Hoatth, Education

  13. Characterisation of plastic packaging waste for recycling: problems related to current approaches

    DEFF Research Database (Denmark)

    Götze, Ramona; Astrup, Thomas Fruergaard

    2013-01-01

    criteria of recycling processes. A lack of information in current waste characterisation practise on polymer resin composition, black coloured material content and the influence of surface adherent material on physico-chemical characteristics of plastic packaging waste were identified. These shortcomings...

  14. Computational materials science: Nanoscale plasticity

    DEFF Research Database (Denmark)

    Jacobsen, Karsten Wedel; Schiøtz, Jakob

    2002-01-01

    How does plastic deformation of polycrystalline materials with grain sizes less than 100 nm look at the atomic scale? A large-scale molecular dynamics simulation of nanocrystalline alluminium reveals some surprising behaviour.......How does plastic deformation of polycrystalline materials with grain sizes less than 100 nm look at the atomic scale? A large-scale molecular dynamics simulation of nanocrystalline alluminium reveals some surprising behaviour....

  15. DEHA-plasticized PVC for retail packaging of fresh meat

    DEFF Research Database (Denmark)

    Petersen, Jens Højslev; Naamansen, Ebbe Tubæk

    1998-01-01

    A selection of frequently consumed meat products were packed in two commercial types of plasticized PVC film with declared plasticizer compositions of 11 and 21% di-(ethylhexyl)adipate (DEHA), respectively. The meat products were analysed for DEHA after packaging and storage until their "use by......" date. Pretreatment of the meat, including cutting, chopping, cooking and packaging, was performed according to normal practice in a Danish supermarket. All samples contained DEHA, in general the investigation showed that a high fat content in or at the surface of the meat and/or a high storage...

  16. The Model 9977 Radioactive Material Packaging Primer

    Energy Technology Data Exchange (ETDEWEB)

    Abramczyk, G. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2015-10-09

    The Model 9977 Packaging is a single containment drum style radioactive material (RAM) shipping container designed, tested and analyzed to meet the performance requirements of Title 10 the Code of Federal Regulations Part 71. A radioactive material shipping package, in combination with its contents, must perform three functions (please note that the performance criteria specified in the Code of Federal Regulations have alternate limits for normal operations and after accident conditions): Containment, the package must “contain” the radioactive material within it; Shielding, the packaging must limit its users and the public to radiation doses within specified limits; and Subcriticality, the package must maintain its radioactive material as subcritical

  17. Hanford Site radioactive hazardous materials packaging directory

    Energy Technology Data Exchange (ETDEWEB)

    McCarthy, T.L.

    1995-12-01

    The Hanford Site Radioactive Hazardous Materials Packaging Directory (RHMPD) provides information concerning packagings owned or routinely leased by Westinghouse Hanford Company (WHC) for offsite shipments or onsite transfers of hazardous materials. Specific information is provided for selected packagings including the following: general description; approval documents/specifications (Certificates of Compliance and Safety Analysis Reports for Packaging); technical information (drawing numbers and dimensions); approved contents; areas of operation; and general information. Packaging Operations & Development (PO&D) maintains the RHMPD and may be contacted for additional information or assistance in obtaining referenced documentation or assistance concerning packaging selection, availability, and usage.

  18. ALTERNATE MATERIALS IN DESIGN OF RADIOACTIVE MATERIAL PACKAGES

    Energy Technology Data Exchange (ETDEWEB)

    Blanton, P.; Eberl, K.

    2010-07-09

    This paper presents a summary of design and testing of material and composites for use in radioactive material packages. These materials provide thermal protection and provide structural integrity and energy absorption to the package during normal and hypothetical accident condition events as required by Title 10 Part 71 of the Code of Federal Regulations. Testing of packages comprising these materials is summarized.

  19. IC chip stress during plastic package molding

    Energy Technology Data Exchange (ETDEWEB)

    Palmer, D.W.; Benson, D.A.; Peterson, D.W.; Sweet, J.N.

    1998-02-01

    Approximately 95% of the world`s integrated chips are packaged using a hot, high pressure transfer molding process. The stress created by the flow of silica powder loaded epoxy can displace the fine bonding wires and can even distort the metalization patterns under the protective chip passivation layer. In this study the authors developed a technique to measure the mechanical stress over the surface of an integrated circuit during the molding process. A CMOS test chip with 25 diffused resistor stress sensors was applied to a commercial lead frame. Both compression and shear stresses were measured at all 25 locations on the surface of the chip every 50 milliseconds during molding. These measurements have a fine time and stress resolution which should allow comparison with computer simulation of the molding process, thus allowing optimization of both the manufacturing process and mold geometry.

  20. High reliability plastic packaging for microelectronics

    Energy Technology Data Exchange (ETDEWEB)

    Sweet, J.N.; Peterson, D.W.; Hsia, A.H.; Tuck, M.

    1997-07-01

    Goal was Assembly Test Chips (ATCs) which could be used for evaluating plastic encapsulation technologies. Circuits were demonstrated for measuring Au-Al wirebond and Al metal corrosion failure rates during accelerated temperature and humidity testing. The test circuits on the ATC02.5 chip were very sensitive to extrinsic or processing induced failure rates. Accelerated aging experiments were conducted with unpassivated triple track Al structures on the ATC02.6 chip; the unpassivated tracks were found to be very sensitive to particulate contamination. Some modifications to existing circuitry were suggested. The piezoresistive stress sensing circuitry designed for the ATC04 test chip was found suitable for determining the change in the state of mechanical stress at the die when both initial and final measurements were made near room temperature (RT). Attempt to measure thermal stress between RT and a typical polymer glass transition temperature failed because of excessive die resistor- substrate leakage currents at the high temperature end; suitable circuitry changes were developed to overcome this problem. One temperature and humidity experiment was conducted with Sandia developed static radom access memory parts to examine non-corrosion CMOS failures; this objective was not achieved, but corrosion failure at the metal to Si contacts on the die surface could be detected. This 2-year effort resulted in new designs for test circuits which could be used on an advanced ATC for reliability assessment in Defense Programs electronics development projects.

  1. 食品包装材料生态化发展下的非石油基降解塑料%Non-Petroleum Based Biodegradable Plastic with the Development of Ecologicalization in Food Packaging Materials

    Institute of Scientific and Technical Information of China (English)

    戴宏民; 戴佩燕

    2015-01-01

    -toxic, non-irritating, high strength, easy process-ing and good biocompatibility. Polylactic acid is a kind of biodegradable plastic which could truly realize the dual benefits in ecology and economy with the fastest development. The biodegradable plastic comprehensive properties of butylene succinate are excellent with reasonable cost performance, so it has good application prospect in the fields of food packaging, disposable tableware, packing bottle for medicine, biomedical polymer materials, and auto parts etc. As the packing material, non-petroleum based biodegradable plastic is the inevitable trend with the focus in improving the modified technology and cost control, ensuring non-toxic and harmless to human body, emphasizing individuality, and paying attention to improving the market adoption.

  2. 49 CFR 178.522 - Standards for composite packagings with inner plastic receptacles.

    Science.gov (United States)

    2010-10-01

    ... plastic receptacles. 178.522 Section 178.522 Transportation Other Regulations Relating to Transportation... Standards for composite packagings with inner plastic receptacles. (a) The following are the identification codes for composite packagings with inner plastic receptacles: (1) 6HA1 for a plastic receptacle...

  3. Analysis on the Aging Properties of Wood-plastic Composite Packaging Materials%木塑复合缓冲包装材料老化性能分析

    Institute of Scientific and Technical Information of China (English)

    谭伟平; 肖生苓

    2012-01-01

    阐述和分析木塑复合缓冲包装材料的主要配方组分(木粉、PVC树脂、偶联剂、增塑剂等)在不同的自然因素的影响下,对其结构、力学性能等的影响,进而为在实验时采用不同组分制作实验材料提供简单参考。其次,简单讲述了人工气候老化试验机的相关类型,以及每一种装置的各自使用事项及优缺点,为在实验时选用何种老化设备提供有力的参考。最后,又列举了人工模拟设备在实验中应注意的相关问题,以避免实验中出现的人为误差而造成实验结果与实际的偏离。%The paper describes and analyzes the impacts of the main formula components(wood powder,PVC resin,coupling agent,plasticizer,etc.) of wood and plastic composite cushion packaging material on its structure and mechanical properties under different conditions.The types and characteristics of the aging test equipment for wood and plastic composites were elaborated which will provide reference for the selection of aging test equlpment.Some related problems while simulating the equipment were put forward to avoid human errors in the experiment.

  4. New Polymer Materials for Microelectronics Packaging

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    @@ Researchers at the CAS Institute of Chemistry (ICCAS) have made breakthrough progress in developing the manufacturing technology of advanced polymer materials for microelectronics packaging applications. The advanced integrated circuit (IC) packaging polymer materials, including photoimageable polyimide resins and liquid epoxy underfills, are a key issue for FC-BGA/CSP(flip chip-ball grill array/chip scale packaging) which is the main stream for the next generation of microelectronics devices. With the down-sizing, thinning and high I/O (input/output) of IC chips, microelectronics packaging is now facing a big technology challenge.

  5. Lecture notes on Elasto-plastic materials

    DEFF Research Database (Denmark)

    Hededal, Ole

    2007-01-01

    Brief introduction to material modelling within the framework of rate independent elasto-plastic constitutive modelling......Brief introduction to material modelling within the framework of rate independent elasto-plastic constitutive modelling...

  6. Polyhydroxyalkanoates (PHA) Bioplastic Packaging Materials

    Science.gov (United States)

    2010-05-01

    Center CEFPACK - Center for Flexible Packaging CAEFF - Center for Advanced Engineering Films and Fibers T cr - recrystallization temperature...conditions. The tandem line has 1½” primary extruder with a Barr ET screw and a pineapple mixing tip. The gas inject is about 2/3 of the way down the...stretch and shrink film, the equipment at the Center for Flexible Packaging (CEFPACK) and the Center for Advanced Engineering Films and Fibers (CAEFF) at

  7. Screening adulteration of polypropylene bottles with postconsumer recycled plastics for oral drug package by near-infrared spectroscopy.

    Science.gov (United States)

    Xie, Lan-Gui; Sun, Hui-Min; Jin, Shao-Hong

    2011-11-14

    Adulteration of pharmaceutical packaging containers with postconsumer recycled plastic materials was considerably difficult to identify due to the similar chemical compositions of virgin and recycled plastics. In the present study, near-infrared (NIR) spectroscopy coupled with conformity test was proposed to screen the adulteration of pharmaceutical packaging containers. Two kinds of representative screening models were investigated on polypropylene (PP) bottles for oral drug package. The reliability of the screening models was validated through studying the identification reliability, specificity, and robustness of the methods. The minimum spiking level of two modeled adulterants at the proportion of 20% could be detected, and the unqualified sample from a domestic manufacturer was rejected by this developed method. This strategy represents a rapid and promising analytical method for screening the adulteration of pharmaceutical plastic packaging containers with postconsumer recycled plastics.

  8. Material Design and Technology of Cartonboard Packaging

    OpenAIRE

    Marttila, Erno

    2012-01-01

    This thesis explores the different types of cartonboard packages through the whole line of their manufacturing process from choosing the right materials for the board in to final converting processes. Producing efficient, environmentally friendly and most of all right kind of cartonboard package is the core theme in this work. This work is publicly available and can be used as a reference by anyone who needs to learn the basics and some of the more advanced things of cartonboard packaging....

  9. Packaging Materials Outgassing Study Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Smith, R. A. [Oak Ridge Y-12 Plant (Y-12), Oak Ridge, TN (United States)

    2006-09-26

    An outgassing study was conducted on two polyurethane packaging foams, two polymer bottles (polytetrafluoroethylene and polyethylene), and two polymer lids. The purpose was to measure the volume of gases that diffuse from these packaging materials at a maximum of 400-degrees F when stored in ambient air within sealed containers.

  10. Plastic Recycling Experiments in Materials Education

    Science.gov (United States)

    Liu, Ping; Waskom, Tommy L.

    1996-01-01

    The objective of this project was to introduce a series of plastic recycling experiments to students in materials-related courses such as materials science, material technology and materials testing. With the plastic recycling experiments, students not only can learn the fundamentals of plastic processing and properties as in conventional materials courses, but also can be exposed to the issue of materials life cycle and the impact on society and environment.

  11. Dynamic modelling of packaging material flow systems.

    Science.gov (United States)

    Tsiliyannis, Christos A

    2005-04-01

    A dynamic model has been developed for reused and recycled packaging material flows. It allows a rigorous description of the flows and stocks during the transition to new targets imposed by legislation, product demand variations or even by variations in consumer discard behaviour. Given the annual reuse and recycle frequency and packaging lifetime, the model determines all packaging flows (e.g., consumption and reuse) and variables through which environmental policy is formulated, such as recycling, waste and reuse rates and it identifies the minimum number of variables to be surveyed for complete packaging flow monitoring. Simulation of the transition to the new flow conditions is given for flows of packaging materials in Greece, based on 1995--1998 field inventory and statistical data.

  12. Deformation mechanisms of plasticized starch materials.

    Science.gov (United States)

    Mikus, P-Y; Alix, S; Soulestin, J; Lacrampe, M F; Krawczak, P; Coqueret, X; Dole, P

    2014-12-19

    The aim of this paper is to understand the influence of plasticizer and plasticizer amount on the mechanical and deformation behaviors of plasticized starch. Glycerol, sorbitol and mannitol have been used as plasticizers. After extrusion of the various samples, dynamic mechanical analyses and video-controlled tensile tests have been performed. It was found that the nature of plasticizer, its amount as well as the aging of the material has an impact on the involved deformation mechanism. The variations of volume deformation could be explained by an antiplasticization effect (low plasticizer amount), a phase-separation phenomenon (excess of plasticizer) and/or by the retrogradation of starch.

  13. 49 CFR 173.36 - Hazardous materials in Large Packagings.

    Science.gov (United States)

    2010-10-01

    ... an inner packaging is constructed of paper or flexible plastic, the inner packaging must be replaced... the transportation of liquids with a flash point of 60.5 °C (141 °F) (closed cup) or lower, or...

  14. Optimization of biomass blends in the manufacture of molded packaging materials produced using fungal mycelium

    Science.gov (United States)

    Polystyrene is one of the most widely used plastics and is commonly produced in three forms: 1) Extruded polystyrene – disposable utensils, CD/DVD cases, yogurt containers, smoke alarm housing, etc.; 2) Expanded polystyrene foam – molded packaging materials and packaging "peanuts"; 3) Extruded polys...

  15. Detection of Phthalic Acid Esters in Food Plastic Packaging Materials%食品塑料包装材料中邻苯二甲酸酯类物质的检测

    Institute of Scientific and Technical Information of China (English)

    别同玉

    2015-01-01

    Contents of six phthalic acid esters (PAEs) including dimethyl phthalate (DMP), diethyl phthalate (DEP), dibutyl phthalate (DBP), benzyl butyl phthalate (BBP), di-(2-ethylhexyl) phthalate (DEHP), Di-n-octyl phthalate (DNOP) in nine kinds of food plastic packaging materials were investigated by solid phase extraction-gas chromatography. The results showed that the PAEs recovery rates ranged from 83.2%to 106.9%while the relative standard deviations ranged from 1.6% to 6.2 %. PAEs were found in all the nine kinds of packaging materials. Among them, DBP existed in all the samples. DEHP was detected in 66.67%of the total samples. All the contents of PAEs detected exceeded the European Standard (0.3 mg/kg bw).%采用固相萃取-气相色谱法测定9种不同食品塑料包装材料中的6种邻苯二甲酸酯[邻苯二甲酸二甲酯(DMP)、邻苯二甲酸二乙酯(DEP)、邻苯二甲酸二丁酯(DBP)、邻苯二甲酸丁基苄基酯(BBP)、邻苯二甲酸二(2-乙基己基)酯(DEHP)、邻苯二甲酸二正辛酯(DNOP)]的含量。结果表明,回收率介于83.2%~106.9%区间,相对标准偏差(RSD)介于1.6%~6.2%区间。9种抽检的食品塑料包装材料中全部检出了邻苯二甲酸酯(PAEs),其中DBP存在于所有抽检样品中,且66.67%的样品中含有DEHP,检出的邻苯二甲酸酯类物质的含量均高于欧洲规定的每天0.3 mg/kg体重的标准。

  16. Stability Study of Sunscreens with Free and Encapsulated UV Filters Contained in Plastic Packaging

    Directory of Open Access Journals (Sweden)

    Benedetta Briasco

    2017-05-01

    Full Text Available Sunscreens play a fundamental role in skin cancer prevention and in protection against photo-aging. UV filters are often photo-unstable, especially in relation to their vehicles and, being lipophilic substances, they are able to interact with plastic packaging. Finally, UV filter stability can be significantly affected by the routine use of the product at high temperatures. This work aims to study the stability of sunscreen formulations in polyethylene packaging. Butyl methoxydibenzoylmethane and octocrylene, both in a free form and as encapsulated filters were chosen as UV filters. Stability evaluations were performed both in the packaging and on the formulations. Moreover, a further two non-destructive techniques, near-infrared (NIR spectroscopy and a multiple light scattering technique, were also used to evaluate the stability of the formulation. Results demonstrated clearly that all of the pack underwent significant changes in its elastic/plastic behavior and in external color after solar irradiation. From the evaluation of the extractable profile of untreated and treated packaging material an absorption of 2-phenoxyethanol and octocrylene were shown. In conclusion, the results highlighted clearly that a reduction of the UV filter in the formulation packed in high-density polyethylene/low-density polyethylene (HDPE/LDPE material can occur over time, reducing the protective effect of the product when applied to the skin.

  17. Stability Study of Sunscreens with Free and Encapsulated UV Filters Contained in Plastic Packaging.

    Science.gov (United States)

    Briasco, Benedetta; Capra, Priscilla; Mannucci, Barbara; Perugini, Paola

    2017-05-31

    Sunscreens play a fundamental role in skin cancer prevention and in protection against photo-aging. UV filters are often photo-unstable, especially in relation to their vehicles and, being lipophilic substances, they are able to interact with plastic packaging. Finally, UV filter stability can be significantly affected by the routine use of the product at high temperatures. This work aims to study the stability of sunscreen formulations in polyethylene packaging. Butyl methoxydibenzoylmethane and octocrylene, both in a free form and as encapsulated filters were chosen as UV filters. Stability evaluations were performed both in the packaging and on the formulations. Moreover, a further two non-destructive techniques, near-infrared (NIR) spectroscopy and a multiple light scattering technique, were also used to evaluate the stability of the formulation. Results demonstrated clearly that all of the pack underwent significant changes in its elastic/plastic behavior and in external color after solar irradiation. From the evaluation of the extractable profile of untreated and treated packaging material an absorption of 2-phenoxyethanol and octocrylene were shown. In conclusion, the results highlighted clearly that a reduction of the UV filter in the formulation packed in high-density polyethylene/low-density polyethylene (HDPE/LDPE) material can occur over time, reducing the protective effect of the product when applied to the skin.

  18. Packaging and transportation of radioactive materials

    Energy Technology Data Exchange (ETDEWEB)

    None

    1978-01-01

    The presentations made at the Symposium on Packaging and Transportation of Radioactive Materials are included. The purpose of the meeting was for the interchange of information on the technology and politics of radioactive material transportation. Separate abstracts were prepared for individual items. (DC)

  19. Aqueous Corrosion Rates for Waste Package Materials

    Energy Technology Data Exchange (ETDEWEB)

    S. Arthur

    2004-10-08

    The purpose of this analysis, as directed by ''Technical Work Plan for: Regulatory Integration Modeling and Analysis of the Waste Form and Waste Package'' (BSC 2004 [DIRS 171583]), is to compile applicable corrosion data from the literature (journal articles, engineering documents, materials handbooks, or standards, and national laboratory reports), evaluate the quality of these data, and use these to perform statistical analyses and distributions for aqueous corrosion rates of waste package materials. The purpose of this report is not to describe the performance of engineered barriers for the TSPA-LA. Instead, the analysis provides simple statistics on aqueous corrosion rates of steels and alloys. These rates are limited by various aqueous parameters such as temperature (up to 100 C), water type (i.e., fresh versus saline), and pH. Corrosion data of materials at pH extremes (below 4 and above 9) are not included in this analysis, as materials commonly display different corrosion behaviors under these conditions. The exception is highly corrosion-resistant materials (Inconel Alloys) for which rate data from corrosion tests at a pH of approximately 3 were included. The waste package materials investigated are those from the long and short 5-DHLW waste packages, 2-MCO/2-DHLW waste package, and the 21-PWR commercial waste package. This analysis also contains rate data for some of the materials present inside the fuel canisters for the following fuel types: U-Mo (Fermi U-10%Mo), MOX (FFTF), Thorium Carbide and Th/U Carbide (Fort Saint Vrain [FSVR]), Th/U Oxide (Shippingport LWBR), U-metal (N Reactor), Intact U-Oxide (Shippingport PWR, Commercial), aluminum-based, and U-Zr-H (TRIGA). Analysis of corrosion rates for Alloy 22, spent nuclear fuel, defense high level waste (DHLW) glass, and Titanium Grade 7 can be found in other analysis or model reports.

  20. Compounds in food packaging materials

    DEFF Research Database (Denmark)

    Rosenmai, Anna Kjerstine

    Food contact materials (FCMs) are sources of food contamination and human chemical exposure. Some chemicals in these materials are known to cause adverse effects, but many are poorly characterized for their potential toxicological hazards making risk assessment a challenge. The aim of the project......, but subgroups of fluorinated chemicals had similar profiles. Polyfluoroalkyl phosphate ester surfactants (PAPs) generally decreased progestagen and androgen levels, fluorotelomer alcohols (FTOHs) generally increased ER activity, and long-chained perfluorinated alkyl carboxylic acids (PFCAs) generally increased...

  1. Upgrading of recycled plastics obtained from flexible packaging waste by adding nanosilicates

    Science.gov (United States)

    Garofalo, E.; Claro, M.; Scarfato, P.; Di Maio, L.; Incarnato, L.

    2015-12-01

    Currently, the growing consumption of polymer products creates large quantities of waste materials resulting in public concern in the environment and people life. The efficient treatment of polymer wastes is still a difficult challenge and the recycling process represents the best way to manage them. Recently, many researchers have tried to develop nanotechnology for polymer recycling. The products prepared through the addition of nanoparticles to post-used plastics could offer the combination of improved properties, low weight, easy of processing and low cost which is not easily and concurrently found by other methods of plastic recycling. In this study materials, obtained by the separation and mechanical recycling of post-consumer packaging films of small size (organic modifier, were melt compounded with the recycled materials in a twin-screw extruder. The morphological, thermal, rheological and mechanical properties of the prepared nanocomposites were extensively discussed.

  2. 19 CFR 10.461 - Retail packaging materials and containers.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 1 2010-04-01 2010-04-01 false Retail packaging materials and containers. 10.461... Free Trade Agreement Rules of Origin § 10.461 Retail packaging materials and containers. Packaging materials and containers in which a good is packaged for retail sale, if classified with the good for...

  3. 19 CFR 10.539 - Retail packaging materials and containers.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 1 2010-04-01 2010-04-01 false Retail packaging materials and containers. 10.539...-Singapore Free Trade Agreement Rules of Origin § 10.539 Retail packaging materials and containers. Packaging materials and containers in which a good is packaged for retail sale, if classified with the good for...

  4. Chitosan films and blends for packaging material.

    Science.gov (United States)

    van den Broek, Lambertus A M; Knoop, Rutger J I; Kappen, Frans H J; Boeriu, Carmen G

    2015-02-13

    An increased interest for hygiene in everyday life as well as in food, feed and medical issues lead to a strong interest in films and blends to prevent the growth and accumulation of harmful bacteria. A growing trend is to use synthetic and natural antimicrobial polymers, to provide non-migratory and non-depleting protection agents for application in films, coatings and packaging. In food packaging, antimicrobial effects add up to the barrier properties of the materials, to increase the shelf life and product quality. Chitosan is a natural bioactive polysaccharide with intrinsic antimicrobial activity and, due to its exceptional physicochemical properties imparted by the polysaccharide backbone, has been recognized as a natural alternative to chemically synthesized antimicrobial polymers. This, associated with the increasing preference for biofunctional materials from renewable resources, resulted in a significant interest on the potential for application of chitosan in packaging materials. In this review we describe the latest developments of chitosan films and blends as packaging material. Copyright © 2014 Elsevier Ltd. All rights reserved.

  5. Eugenol-loaded chitosan nanoparticles: II. Application in bio-based plastics for active packaging.

    Science.gov (United States)

    Woranuch, Sarekha; Yoksan, Rangrong

    2013-07-25

    The aim of the present research was to study the possibility of using eugenol-loaded chitosan nanoparticles as antioxidants for active bio-based packaging material. Eugenol-loaded chitosan nanoparticles were incorporated into thermoplastic flour (TPF) - a model bio-based plastic - through an extrusion process at temperatures above 150°C. The influences of eugenol-loaded chitosan nanoparticles on crystallinity, morphology, thermal properties, radical scavenging activity, reducing power, tensile properties and barrier properties of TPF were investigated. Although the incorporation of 3% (w/w) of eugenol-loaded chitosan nanoparticles significantly reduced the extensibility and the oxygen barrier property of TPF, it provided antioxidant activity and improved the water vapor barrier property. In addition, TPF containing eugenol-loaded chitosan nanoparticles exhibited superior radical scavenging activity and stronger reducing power compared with TPF containing naked eugenol. The results suggest the applicability of TPF containing eugenol-loaded chitosan nanoparticles as an antioxidant active packaging material.

  6. Ingredient of Biomass Packaging Material and Compare Study on Cushion Properties

    Directory of Open Access Journals (Sweden)

    Fangyi Li

    2014-01-01

    Full Text Available In order to reduce the white pollution caused by nondegradable waste plastic packaging materials, the biomass cushion packaging material with straw fiber and starch as the main raw materials had been synthesized. The orthogonal experiment was used to study the impact of mass ratio of fiber to starch, content of plasticizer, active agent, and foaming agent on the compressive strength of cushion material. Infrared spectrometer and theory of water’s bridge-connection were used to study the hydroxyl groups among the fiber and starch. The results were demonstrated as follows: the mass ratio of fiber to starch had the most significant impact on compressive strength. When the contents of the plasticizer, the foaming agent, and the active agent were, respectively, 12%, 0.1%, and 0.3% and the mass ratio of fiber to starch was 2 : 5, the compressive strength was the best up to 0.94 MPa. Meanwhile, with the plasticizer content and the mass ratio of fiber to starch increasing, the cushioning coefficient of the material decreased first and then increased. Comparing the cushion and rebound performance of this material with others, the biomass cushion packaging material could be an ideal substitute of plastic packaging materials such as EPS and EPE.

  7. Chemical compatibility screening results of plastic packaging to mixed waste simulants

    Energy Technology Data Exchange (ETDEWEB)

    Nigrey, P.J.; Dickens, T.G.

    1995-12-01

    We have developed a chemical compatibility program for evaluating transportation packaging components for transporting mixed waste forms. We have performed the first phase of this experimental program to determine the effects of simulant mixed wastes on packaging materials. This effort involved the screening of 10 plastic materials in four liquid mixed waste simulants. The testing protocol involved exposing the respective materials to {approximately}3 kGy of gamma radiation followed by 14 day exposures to the waste simulants of 60 C. The seal materials or rubbers were tested using VTR (vapor transport rate) measurements while the liner materials were tested using specific gravity as a metric. For these tests, a screening criteria of {approximately}1 g/m{sup 2}/hr for VTR and a specific gravity change of 10% was used. It was concluded that while all seal materials passed exposure to the aqueous simulant mixed waste, EPDM and SBR had the lowest VTRs. In the chlorinated hydrocarbon simulant mixed waste, only VITON passed the screening tests. In both the simulant scintillation fluid mixed waste and the ketone mixture simulant mixed waste, none of the seal materials met the screening criteria. It is anticipated that those materials with the lowest VTRs will be evaluated in the comprehensive phase of the program. For specific gravity testing of liner materials the data showed that while all materials with the exception of polypropylene passed the screening criteria, Kel-F, HDPE, and XLPE were found to offer the greatest resistance to the combination of radiation and chemicals.

  8. Thin-Film Coated Plastic Wrap for Food Packaging

    Directory of Open Access Journals (Sweden)

    Hsin-Yu Wu

    2017-07-01

    Full Text Available In this study, the antimicrobial property and food package capability of polymethylpentene (PMP substrate with silicon oxdie (SiOx and organic silicon (SiCxHy stacked layers deposited by an inductively coupled plasma chemical vapor deposition system were investigated. The experimental results show that the stacked pair number of SiOx/SiCxHy on PMP is limited to three pairs, beyond which the films will crack and cause package failure. The three-pair SiOx/SiCxHy on PMP shows a low water vapor transmission rate of 0.57 g/m2/day and a high water contact angle of 102°. Three-pair thin-film coated PMP demonstrates no microbe adhesion and exhibits antibacterial properties within 24 h. Food shelf life testing performed at 28 °C and 80% humidity reports that the three-pair thin-film coated PMP can enhance the food shelf-life to 120 h. The results indicate that the silicon-based thin film may be a promising material for antibacterial food packaging applications to extend the shelf-life of food products.

  9. Thin-Film Coated Plastic Wrap for Food Packaging.

    Science.gov (United States)

    Wu, Hsin-Yu; Liu, Ting-Xuan; Hsu, Chia-Hsun; Cho, Yun-Shao; Xu, Zhi-Jia; Liao, Shu-Chuan; Zeng, Bo-Han; Jiang, Yeu-Long; Lien, Shui-Yang

    2017-07-18

    In this study, the antimicrobial property and food package capability of polymethylpentene (PMP) substrate with silicon oxdie (SiOx) and organic silicon (SiCxHy) stacked layers deposited by an inductively coupled plasma chemical vapor deposition system were investigated. The experimental results show that the stacked pair number of SiOx/SiCxHy on PMP is limited to three pairs, beyond which the films will crack and cause package failure. The three-pair SiOx/SiCxHy on PMP shows a low water vapor transmission rate of 0.57 g/m²/day and a high water contact angle of 102°. Three-pair thin-film coated PMP demonstrates no microbe adhesion and exhibits antibacterial properties within 24 h. Food shelf life testing performed at 28 °C and 80% humidity reports that the three-pair thin-film coated PMP can enhance the food shelf-life to 120 h. The results indicate that the silicon-based thin film may be a promising material for antibacterial food packaging applications to extend the shelf-life of food products.

  10. Analysis of Surrogate Contaminants in Paper-plastic Food Packaging Material by Capillary Gas Chromatography%纸塑复合食品包装材料中模拟污染物的GC检测技术

    Institute of Scientific and Technical Information of China (English)

    黄秀玲; 刘志刚; 王志伟; 许文才; 刘全校

    2009-01-01

    A GC-FID method was established for the determination of photoinitiators (PIs) in paper-plastic packaging material 4015 which solved in 95% ethanol. The pre-treatment protocol for 1 -hydroxycyclohexyl-phenyl ketone and 2 ,2-dimethoxy-2-phenylacotophenone in 95% ethanol was introduced. The influencing factors such as chromatography column, injection mode and velocity of flow of carrier gas were discussed. The results showed that the peaks of two PIs and impurity from paper were completely separated. The linearity was good (0. 999 7 and 0. 999 8) with the detection thresholds of 0. 05mg/L and 0. 1 mg/L, respectively. The RSDs were less than 5% , and the average recovery for Pis in 95% ethanol was in the range of 94% - 107% and 93% - 102% , respectively.%建立了纸塑复合包装材料4015中的模拟墨成分1-羟基环己基苯基甲酮和2,2-二甲氧基-苯基甲酮在脂肪性食品模拟物95%乙醇的气相色谱-氢火焰离子化检测器检测条件,并介绍了体积分数95%乙醇的前处理方法,讨论了色谱柱、进样方式、载气流速对测定的影响.分析结果表明:该法可将2种光引发剂和纸中杂质完全分离,具有较好的线性(相关系数分别为0.999 7和0.999 8),最低检出限分别为0.05 mg/L和0.1 mg/L,测定结果的相对标准偏差均<5.0%,样品在95%乙醇中的平均回收率分别为94%-107%和93%-102%.

  11. Natural materials in Japan is reflected in the package design

    Institute of Scientific and Technical Information of China (English)

    孙云云

    2016-01-01

    Japanese packaging design simple and not drab, has a strong national character, "type" style, but also take into account the Europe and the United States"YangShi" style. Japanese packaging of naturalness, pay attention to packaging material, the nature of the material with its unique design style. This article through to the Japanese brand packaging design case analysis, this paper expounds the Japanese brand packaging design and the use of natural materials. On this basis, further discusses the Japanese brand packaging design concept of innovation to improve the practical significance of China's packaging design innovation.

  12. Predicting diffusion coefficients of chemicals in and through packaging materials.

    Science.gov (United States)

    Fang, Xiaoyi; Vitrac, Olivier

    2017-01-22

    Most of the physicochemical properties in polymers such as activity and partition coefficients, diffusion coefficients, and their activation with temperature are accessible to direct calculations from first principles. Such predictions are particularly relevant for food packaging as they can be used (1) to demonstrate the compliance or safety of numerous polymer materials and of their constitutive substances (e.g. additives, residues…), when they are used: as containers, coatings, sealants, gaskets, printing inks, etc. (2) or to predict the indirect contamination of food by pollutants (e.g. from recycled polymers, storage ambiance…) (3) or to assess the plasticization of materials in contact by food constituents (e.g. fat matter, aroma…). This review article summarizes the classical and last mechanistic descriptions of diffusion in polymers and discusses the reliability of semi-empirical approaches used for compliance testing both in EU and US. It is concluded that simulation of diffusion in or through polymers is not limited to worst-case assumptions but could also be applied to real cases for risk assessment, designing packaging with low leaching risk or to synthesize plastic additives with low diffusion rates.

  13. 78 FR 16044 - Hazardous Materials Packaging-Composite Cylinder Standards; Public Meeting

    Science.gov (United States)

    2013-03-13

    ... reinforced plastic (DOT-FRP) or fully wrapped carbon-fiber reinforced aluminum lined cylinders (DOT- CFFC... TRANSPORTATION Pipeline and Hazardous Materials Safety Administration Hazardous Materials Packaging--Composite... the manufacture, marking, sale and use of non-DOT specification composite cylinders. The...

  14. Ammonia gas permeability of meat packaging materials.

    Science.gov (United States)

    Karim, Faris; Hijaz, Faraj; Kastner, Curtis L; Smith, J Scott

    2011-03-01

    Meat products are packaged in polymer films designed to protect the product from exterior contaminants such as light, humidity, and harmful chemicals. Unfortunately, there is almost no data on ammonia permeability of packaging films. We investigated ammonia permeability of common meat packaging films: low-density polyethylene (LDPE; 2.2 mil), multilayer polyolefin (MLP; 3 mil), and vacuum (V-PA/PE; 3 mil, 0.6 mil polyamide/2.4 mil polyethylene). The films were fabricated into 10 × 5 cm pouches and filled with 50 mL deionized water. Pouches were placed in a plexiglass enclosure in a freezer and exposed to 50, 100, 250, or 500 ppm ammonia gas for 6, 12, 24, and 48 h at -17 ± 3 °C and 21 ± 3 °C. At freezing temperatures, no ammonia residues were detected and no differences in pH were found in the water. At room temperature, ammonia levels and pH of the water increased significantly (P packaging materials have low ammonia permeability and protect meat products exposed to ammonia leaks during frozen storage.

  15. 塑料食品包装的安全性分析%Security analysis of plastic food packaging

    Institute of Scientific and Technical Information of China (English)

    黎盛; 徐丹; 徐毅; 吴习宇

    2011-01-01

    台湾发生的塑化剂事件,再次引发了人们对食品安全的高度关注,同时也引发了人们对塑料食品包装安全的关心。塑料食品包装主要在材料本身、粘合剂和印刷油墨等三个方面对食品安全构成隐形威胁。塑料包装材料内部残留的有毒、有害物质,通过迁移、溶出影响所盛装食品的品质,从而导致食品安全问题。软包装复合薄膜的生产过程中所必须使用的溶剂型聚氨酯粘合剂存在一定的安全隐患,包装印刷油墨存在的色迁移和色渗透对食品安全存在危害等问题。对塑料食品包装的安全性进行分析,以期引发人们对绿色包装的重视和研究。%Taiwan plasticizing agent event had caused great concerns for food safety again,particularly for the safety of plastic food packaging. Plastic food packaging posed invisible threat to food security mainly from three aspects including the plastic food packaging materials themselves,the adhesives’ and the printing inks of plastic packaging. First,the residual toxic and hazardous substances migrating and dissoluting from the plastic packaging affected the food quality,resulting in food security issues. Second,the solvent-based polyurethane adhesives’ which had to be used in the production process of flexible packaging composite films bring risks in food security. And last,the color migration and penetration of packaging printing ink threaten the food security. Therefore,the safety of plastic food packaging was analyzed,in order to call more attention to green packaging.

  16. Effect of Spices and different Packaging Materials on acceptability ...

    African Journals Online (AJOL)

    Effect of Spices and different Packaging Materials on acceptability and shelf-life of ... AFRICAN JOURNALS ONLINE (AJOL) · Journals · Advanced Search · USING ... garlic and nutmeg) as preservatives and use of different packaging materials ...

  17. Plasticity in Ultra Fine Grained Materials

    Energy Technology Data Exchange (ETDEWEB)

    Koslowski, Marisol [Purdue Univ., West Lafayette, IN (United States)

    2015-04-15

    Understanding the mechanisms of deformation of nanocrystalline (nc) materials is critical to the design of micro and nano devices and to develop materials with superior fracture strength and wear resistance for applications in new energy technologies. In this project we focused on understanding the following plastic deformation processes described in detail in the following sections: 1. Plastic strain recovery (Section 1). 2. Effect of microstructural variability on the yield stress of nc metals (Section 2). 3. The role of partial and extended full dislocations in plastic deformation of nc metals (Section 3).

  18. Microwave Absorbent Packaging Material from Composites Chitosan-Polyvinyl Alcohol Polymer

    Directory of Open Access Journals (Sweden)

    Bambang - Riyanto

    2015-07-01

    Full Text Available Microwave absorbent packaging materials currently tend to biomaterial. Chitosan is a dielectric biomaterial with polycationic properties. The aim of this study was to analyze characteristics of microwave absorbing packaging material made from composite chitosan-polyvinyl alcohol (PVA polymer. The ability of the packaging material to absorb microwave was determined by reflection loss measurement. Formed packaging prototype resembles as a thin transparent yellowish plastic with thickness (0.11-0.22 mm and the tensile strength (106.33±2.82-143.00±2.59 kPa. SEM analysis showed homogenous structure characterized by interaction between chitosan and PVA. Optimum absorption value was obtained from chitosan concentration of 1%, with average value of reflection loss was (-31.9289±4.0094 dB.Keywords: chitosan, material packaging, microwave, reflection loss

  19. Microwave Absorbent Packaging Material from Composites Chitosan-Polyvinyl Alcohol Polymer

    Directory of Open Access Journals (Sweden)

    Bambang - Riyanto

    2014-11-01

    Full Text Available Microwave absorbent packaging materials currently tend to biomaterial. Chitosan is a dielectric biomaterial with polycationic properties. The aim of this study was to analyze characteristics of microwave absorbing packaging material made from composite chitosan-polyvinyl alcohol (PVA polymer. The ability of the packaging material to absorb microwave was determined by reflection loss measurement. Formed packaging prototype resembles as a thin transparent yellowish plastic with thickness (0.11-0.22 mm and the tensile strength (106.33±2.82-143.00±2.59 kPa. SEM analysis showed homogenous structure characterized by interaction between chitosan and PVA. Optimum absorption value was obtained from chitosan concentration of 1%, with average value of reflection loss was (-31.9289±4.0094 dB.Keywords: chitosan, material packaging, microwave, reflection loss

  20. The Effect of Packaging Materials on the Quality Attributes of Crayfish During Cold Storage.

    Directory of Open Access Journals (Sweden)

    Ajala, A.S

    2015-11-01

    Full Text Available This study evaluates the effects of packaging materials on the quality attributes of crayfish preserved in cold storage. This was done in order to ascertain the suitability of the different packaging materials on keeping the quality attributes of crayfish in cold storage. The “red claw” crayfish was harvested fresh, beheaded, washed, cleaned and packaged in different packaging materials of low-density polyethylene (LDPE, high-density polyethylene (HDPE, aluminum foil and plastic. The crayfish were stored for a period of eight weeks, and samples were taken for analysis every two weeks. The analyses carried out were proximate, mineral (calcium, iron and phosphorus and microbial (yeast, mould, coliform and total viable counts. There were significant reduction changes in the proximate, minerals and microbiological analysis in respect to the packaging materials and storage period.

  1. Material flow analysis for an industry - A case study in packaging

    Science.gov (United States)

    Amey, E.B.; Sandgren, K.

    1996-01-01

    The basic materials used in packaging are glass, metals (primarily aluminum and steel), an ever-growing range of plastics, paper and paperboard, wood, textiles for bags, and miscellaneous other materials (such as glues, inks, and other supplies). They are fabricated into rigid, semi-rigid, or flexible containers. The most common forms of these containers include cans, drums, bottles, cartons, boxes, bags, pouches, and wraps. Packaging products are, for the most part, low cost, bulky products that are manufactured close to their customers. There is virtually no import or export of packaging products. A material flow analysis can be developed that looks at all inputs to an industrial sector, inventories the losses in processing, and tracks the fate of the material after its useful life. An example is presented that identifies the material inputs to the packaging industry, and addresses the ultimate fate of the materials used. ?? 1996 International Association for Mathematical Geology.

  2. Plasticity of pressure-sensitive materials

    CERN Document Server

    Ochsner, Andreas

    2014-01-01

    Classical plasticity theory of metals is independent of the hydrostatic pressure. However, if the metal contains voids or pores or if the structure is composed of cells, this classical assumption is no more valid and the influence of the hydrostatic pressure must be incorporated in the constitutive description. Looking at the microlevel, metal plasticity is connected with the uniform planes of atoms organized with long-range order. Planes may slip past each other along their close-packed directions. The result is a permanent change of shape within the crystal and plastic deformation. The presence of dislocations increases the likelihood of planes slipping. Nowadays, the theory of pressure sensitive plasticity is successfully applied to many other important classes of materials (polymers, concrete, bones etc.) even if the phenomena on the micro-level are different to classical plasticity of metals. The theoretical background of this phenomenological approach based on observations on the macro-level is describe...

  3. Energy implications of recycling packaging materials

    Energy Technology Data Exchange (ETDEWEB)

    Gaines, L.L. [Argonne National Lab., IL (United States); Stodolsky, F. [Argonne National Lab., Washington, DC (United States)

    1994-03-01

    In 1992, Congress sought to rewrite the United States comprehensive solid waste legislation -- the Resource Conservation and Recovery Act (RCRA). Commodity-specific recycling rates were proposed for consumer-goods packaging materials and newsprint We compare the impacts on energy, materials use, and landfill volume of recycling at those rates to the impacts for alternative methods of material disposition to determine the optimum for each material. After products have served their intended uses, there are several alternative paths for material disposition. These include reuse, recycling to the same product, recycling to a lower-valued product, combustion for energy recovery, incineration without energy recovery, and landfill. Only options considered to be environmentally sound are Included. Both houses of Congress specifically excluded combustion for energy recovery from counting towards the recovery goats, probably because combustion is viewed as a form of disposal and is therefore assumed to waste resources and have n environmental effects. However, co-combustion in coal-fired plants or combustion in appropriately pollution-controlled waste-to-energy plants Is safe, avoids landfill costs, and can displace fossil fuels. In some cases, more fossil fuels can be displaced by combustion than by recycling. We compare the alternative life-cycle energies to the energies for producing the products from virgin materials. Results depend on the material and on the objective to be achieved. There are trade-offs among possible goals. For instance, paper packaging recycling conserves trees but may require greater fossil-fuel input than virgin production. Therefore, the objectives for proposed legislation must be examined to see whether they can most effectively be achieved by mandated recycling rates or by other methods of disposition. The optimal choices for the United States may not necessarily be the same as those for Europe and other parts of the world.

  4. Phthalate migration from packaging materials into food

    Directory of Open Access Journals (Sweden)

    Soňa Bogdanovičová

    2015-08-01

    Full Text Available The content of dibutylphthalate (DBP and di- (2-ethylhexyl phthalate (DEHP in samples of packages used for packaging meat productsand the phthalate migration from packaging materials to meat products were studied. Five samples of textile packaging intended for cooked meat production were analysed as well asthe final product which was filled into packages. Subsequently an analysis was carried out (after 1, 7, 14, 21, and 28 days of storage of the finished meat products stored over the course of their intended shelf life at ambient temperature of 4 °C. Determination of phthalates was conducted by high performance liquid chromatography (HPLC method with UV detection at a wavelength of 224 nm on the Zorbax Eclipse C8 column. The content of phthalates in the final product was below the limit of quantification. According to the Regulation of the Commission (EU No. 10/2011, the specific migration limit of products intended for food contact is 1.5 mg.kg-1of food simulant for DEHP and 0.3 mg.kg-1 for DBP. After filling and the first day of storage of the meat product, four package samples release the said phthalates to an extent that it exceeded the limits of the Commission Regulation (EU No. 10/2011. Already after the seventh day of storage, all samples (with the exception of sample 2 for DBP exceeded SMLs. Monitoring of each phthalate migration in individual samples during storage (for 28 days produced a rising tendency.  In sample 1, DBP increased from 0.40 to 3.37 mg.kg-1, while DEHP from 0.58 to 14.66 mg.kg-1. In sample 2, DBP increased from ≤0.2 mg.kg-1 to 4.34 mg.kg-1, whileDEHP from 1.46 to 28.20 mg.kg-1. In sample 3, DBP increased from ≤0.2 mg.kg-1 to  8.27 mg.kg-1, while DEHP from 1.67 to 14.84 mg.kg-1. In sample 4, DBP increased from 0.27 to 6.12 mg.kg-1, while DEHP from 2.37 to 13.22 mg.kg-1. In sample 5, DBP increased from 0.32 to 11.11 mg.kg-1, while DEHP from 1.91 to 15.42 mg.kg-1.

  5. Packaging performance evaluation and performance oriented packaging standards for large packages for poison inhalation hazard materials

    Energy Technology Data Exchange (ETDEWEB)

    Griego, N.R.; Mills, G.S.; McClure, J.D. [and others

    1997-07-01

    The U.S. Department of Transportation Research & Special Programs Administration (DOT-RSPA) has sponsored a project at Sandia National Laboratories to evaluate the protection provided by current packagings used for truck and rail transport of materials that have been classified as Poison Inhalation Hazards (PIH) and to recommend performance standards for these PIH packagings. Hazardous materials span a wide range of toxicity and there are many parameters used to characterize toxicity; for any given hazardous material, data are not available for all of the possible toxicity parameters. Therefore, it was necessary to select a toxicity criterion to characterize all of the PIH compounds (a value of the criterion was derived from other parameters in many cases) and to calculate their dispersion in the event of a release resulting from a transportation accident. Methodologies which account for material toxicity and dispersal characteristics were developed as a major portion of this project and applied to 72 PIH materials. This report presents details of the PIH material toxicity comparisons, calculation of their dispersion, and their classification into five severity categories. 16 refs., 5 figs., 7 tabs.

  6. Biodegradable packaging materials conception based on starch and polylactic acid (PLA) reinforced with cellulose.

    Science.gov (United States)

    Masmoudi, Fatma; Bessadok, Atef; Dammak, Mohamed; Jaziri, Mohamed; Ammar, Emna

    2016-10-01

    The plastic materials used for packaging are increasing leading to a considerable amount of undegradable solid wastes. This work deals with the reduction of conventional plastics waste and the natural resources preservation by using cellulosic polymers from renewable resources (alfa and luffa). Plasticized starch films syntheses were achieved at a laboratory scale. These natural films showed some very attractive mechanical properties at relatively low plasticizers levels (12 to 17 % by weight). Furthermore, mixtures including polylactic acid polymer (PLA) and cellulose fibers extracted from alfa and luffa were investigated by melt extrusion technique. When used at a rate of 10 %, these fibers improved the mixture mechanical properties. Both developed materials were biodegradable, but the plasticized starch exhibited a faster biodegradation kinetic compared to the PLA/cellulose fibers. These new materials would contribute to a sustainable development and a waste reduction.

  7. A comprehensive waste collection cost model applied to post-consumer plastic packaging waste

    NARCIS (Netherlands)

    Groot, J.J.; Bing, X.; Bos-Brouwers, H.E.J.; Bloemhof, J.M.

    2014-01-01

    Post-consumer plastic packaging waste (PPW) can be collected for recycling via source separation or post-separation. In source separation, households separate plastics from other waste before collection, whereas in post-separation waste is separated at a treatment centre after collection. There are

  8. A comprehensive waste collection cost model applied to post-consumer plastic packaging waste

    NARCIS (Netherlands)

    Groot, J.J.; Bing, X.; Bos-Brouwers, H.E.J.; Bloemhof, J.M.

    2014-01-01

    Post-consumer plastic packaging waste (PPW) can be collected for recycling via source separation or post-separation. In source separation, households separate plastics from other waste before collection, whereas in post-separation waste is separated at a treatment centre after collection. There are

  9. 高阻隔高温杀菌易撕食品软塑包装材料性能的研究%Study on Properties of High-resistance and High-temperature Sterilization and Easy Tear Flexible Plastic for Food Packaging Material

    Institute of Scientific and Technical Information of China (English)

    宫建华; 黄俊彦; 梁现峰; 曹福林

    2011-01-01

    选用不同厂家生产的聚对苯二甲酸乙二醇酯(PET)、铝箔(AL)、流延聚丙烯(CPP)及相应的黏合剂和醇性油墨等原料,选定软塑包装材料结构为PET/AL/CPP,进行了一系列生产工艺实验和产品检测分析,从而得出该软塑包装新材料具有极高的阻氧阻湿性能、耐高温杀菌性能和良好的单向易撕裂性能.%Selecting PET, aluminum foil(AL), chlorinated polypropylene(CPP), adhesives. And alcohol inks manufactured by different factories as raw materials, a kind of flexible plastic packaging materials of PET/AL/CPP was prepared, and then a series of production processing experiments and product testing analysis were done. The results show that the flexible plastic packaging materials possess excellent resistance oxygen performance and resistance wet performance, high-temperature sterilization and good one-way easy tear.

  10. Aktau Plastics Plant Explosives Material Report

    Energy Technology Data Exchange (ETDEWEB)

    CASE JR.,ROGER S.

    1999-12-01

    The U.S. Department of Energy (DOE) has been cooperating with the Republic of Kazakhstanin Combined Threat Reduction (CTR) activities at the BN350 reactor located at the Mangyshlak Atomic Energy Complex (MAEC) in the city of Aktau, Kazakhstan since 1994. DOE contract personnel have been stationed at this facility for the last two years and DOE representatives regularly visit this location to oversee the continuing cooperative activities. Continued future cooperation is planned. A Russian news report in September 1999 indicated that 75 metric tons of organic peroxides stored at the Plastics Plant near Aktau were in danger of exploding and killing or injuring nearby residents. To ensure the health and safety of the personnel at the BN350 site, the DOE conducted a study to investigate the potential danger to the BN350 site posed by these materials at the Plastics Plant. The study conclusion was that while the organic peroxides do have hazards associated with them, the BN350 site is a safe distance from the Plastics Plant. Further, because the Plastics Plant and MAEC have cooperative fire-fighting agreements,and the Plastics Plant had exhausted its reserve of fire-fighting foam, there was the possibility of the Plastics Plant depleting the store of fire-fighting foam at the BN350 site. Subsequently, the DOE decided to purchase fire-fighting foam for the Plastics Plant to ensure the availability of free-fighting foam at the BN350 site.

  11. Plastic materials currently used in Mongolia

    Institute of Scientific and Technical Information of China (English)

    Ruvjir Shagdarsuren; Nachin Baasanjav; Sosor Baatarjav

    2007-01-01

    The first skin-flap procedures were performed in Mongolia by a team of Chinese doctors ( Chenod, Chen)who treated children with burn injuries in the 1950s. The field of plastic surgery was further developed through assistance from the former Soviet Union and is now widely practiced by a number of surgeons around the country.In recent years, the fast evolving field of plastic surgery in Mongolia has created a need for clear and consistent system for the classification of various plastic materials. A team of Mongolian surgeons at the National Hospital for Traumatology, Orthopedics, Rehabilitation and Teaching Research have completed a research programme aimed at adopting a leading classification system that can facilitate effective communication between plastic surgeons. This requires the chosen system to be in line with modern trends in plastic surgery and the established international norms.As a result of extensive research and analysis, they have developed a customized version of Vasiliev's classification that focuses on formulating general principles of the description of plastic materials based on their functional characteristics. The main reason for this selection is its similarity with existing Mongolian standards as well as its principles that contain important implications for surgery.

  12. 49 CFR 173.40 - General packaging requirements for toxic materials packaged in cylinders.

    Science.gov (United States)

    2010-10-01

    ... concrete or steel, impacting at an orientation most likely to cause damage. “Deformation”means a cylinder... packaged in cylinders. 173.40 Section 173.40 Transportation Other Regulations Relating to Transportation... Transportation § 173.40 General packaging requirements for toxic materials packaged in cylinders. When this...

  13. Identification of fatty foods with contamination possibilities by plasticizers when stored in PVC film packaging

    Directory of Open Access Journals (Sweden)

    Hilda Duval Barros

    2011-06-01

    Full Text Available Poly-(vinyl chloride (PVC requires the addition of plasticizers - additives that give flexibility and malleability for its processing into flexible film. The most used ones are: di-(2-ethylhexyl adipate (DEHA and di-(2-ethylhexyl phthalate (DEHP. Toxic effects of DEHP have been observed by several authors. Phthalates are being replaced by alternative substances in PVC flexible products, because of their possible toxicological effects. DEHA is a substitute for phthalates widely used as a plasticizer in PVC materials for involving food. Some authors have shown that the exposure to DEHA also induces toxicity. A cross-sectional study was performed to identify which fatty foods carry the possibility of contamination by DEHP and DEHA. Eighteen different foods with at least 3% (m/m fat and the possibility of being wrapped in plastic film were determined. This study suggested that all foods were subject to contamination by DEHP and DEHA in those conditions - in decreasing consumption order of 96 to 22% in the convenience sample. New guidelines on the limits of DEHA and DEHP established by the Brazilian legislation, as additives in PVC film for packaging fatty food, are still relevant to ensure human health.

  14. Acoustic imaging internal microstructure of a packaging material

    OpenAIRE

    Kao-Walter, Sharon; Levin, M. L.; Petronyuk, J.S.; Walter, Mats

    2008-01-01

    Microstructure of a paper-based packaging material was studied by acoustic microscopy method. The laminate structure of the packaging material contains paperboard, polymer and aluminium, which are widely used for aseptic liquid food package. The method has also been used to detect delaminations inside the material. The results show the possibility to study the micro structural features of paperboard, polymer and aluminium foil layered materials by applying the high-resolution ultrasonic acous...

  15. Micromechanical study of plasticity of granular materials

    NARCIS (Netherlands)

    Kruyt, N.P.

    2010-01-01

    Plastic deformation of granular materials is investigated from the micromechanical viewpoint, in which the assembly of particles and interparticle contacts is considered as a mechanical structure. This is done in three ways. Firstly, by investigating the degree of redundancy of the system by compari

  16. Waste Plastic Converting into Hydrocarbon Fuel Materials

    Energy Technology Data Exchange (ETDEWEB)

    Sarker, Moinuddin; Mamunor Rashid, Mohammad; Molla, Mohammad

    2010-09-15

    The increased demand and high prices for energy sources are driving efforts to convert organic compounds into useful hydrocarbon fuels. Although much of this work has focused on biomass, there are strong benefits to deriving fuels from waste plastic material. Natural State Research Inc. (NSR) has invented a simple and economically viable process to decompose the hydrocarbon polymers of waste plastic into the shorter chain hydrocarbon of liquid fuel (patent pending). The method and principle of the production / process will be discussed. Initial tests with several widely used polymers indicate a high potential for commercialization.

  17. External insulation with cellular plastic materials

    DEFF Research Database (Denmark)

    Sørensen, Lars Schiøtt; Nielsen, Anker

    2014-01-01

    External thermal insulation composite systems (ETICS) can be used as extra insulation of existing buildings. The system can be made of cellular plastic materials or mineral wool. There is a European Technical guideline, ETAG 004, that describe the tests that shall be conducted on such systems....... This paper gives a comparison of systems with mineral wool and cellular plastic, based on experience from practice and literature. It is important to look at the details in the system and at long time stability of the properties such as thermal insulation, moisture and fire. Investigation of fire properties...... insulation....

  18. Performance-oriented packagings for hazardous materials: Resource guide

    Energy Technology Data Exchange (ETDEWEB)

    1993-09-01

    This document provides recommendations to US Department of Energy (DOE) shippers regarding packaging that meet performance-oriented packaging requirements implemented by US Department of Transportation (DOT) in rulemaking HM-181 (December 21, 1990) and subsequent actions. The packaging described in this document are certified by their vendor to comply with requirements for Packing Group I, II, or III hazardous materials packaging. The intent of this document is to share information between DOE and contractors and at all DOE facilities.

  19. Directory of certificates of compliance for radioactive materials packages. Summary report of NRC approved packages

    Energy Technology Data Exchange (ETDEWEB)

    None

    1979-10-01

    This directory contains a Summary Report of NRC Approved Packages for radioactive material packages effective September 14, 1979. Purpose of this directory is to make available a convenient source of information on packagings which have been approved by the US Nuclear Regulatory Commission. To assist in identifying packaging, an index by Model Number and corresponding Certificate of Compliance number is included at the back of each volume of the directory. The Summary Report includes a listing of all users of each package design prior to the publication date of the directory.

  20. Technological challenges of addressing new and more complex migrating products from novel food packaging materials.

    Science.gov (United States)

    Munro, Ian C; Haighton, Lois A; Lynch, Barry S; Tafazoli, Shahrzad

    2009-12-01

    The risk assessment of migration products resulting from packaging material has and continues to pose a difficult challenge. In most jurisdictions, there are regulatory requirements for the approval or notification of food contact substances that will be used in packaging. These processes generally require risk assessment to ensure safety concerns are addressed. The science of assessing food contact materials was instrumental in the development of the concept of Threshold of Regulation and the Threshold of Toxicological Concern procedures. While the risk assessment process is in place, the technology of food packaging continues to evolve to include new initiatives, such as the inclusion of antimicrobial substances or enzyme systems to prevent spoilage, use of plastic packaging intended to remain on foods as they are being cooked, to the introduction of more rigid, stable and reusable materials, and active packaging to extend the shelf-life of food. Each new technology brings with it the potential for exposure to new and possibly novel substances as a result of migration, interaction with other chemical packaging components, or, in the case of plastics now used in direct cooking of products, degradation products formed during heating. Furthermore, the presence of trace levels of certain chemicals from packaging that were once accepted as being of low risk based on traditional toxicology studies are being challenged on the basis of reports of adverse effects, particularly with respect to endocrine disruption, alleged to occur at very low doses. A recent example is the case of bisphenol A. The way forward to assess new packaging technologies and reports of very low dose effects in non-standard studies of food contact substances is likely to remain controversial. However, the risk assessment paradigm is sufficiently robust and flexible to be adapted to meet these challenges. The use of the Threshold of Regulation and the Threshold of Toxicological Concern concepts may

  1. Decision support system for material handling and packaging design

    Science.gov (United States)

    Johnsson, Mats I.; Mazouz, Abdel K.; Han, Chingping

    1992-02-01

    The reliability of the materials handling process involving automated stacking of packages on a pallet or automated sorting of packages in a distribution system depends mainly on the design of the package and the material used for the package. Many problems can be eliminated that result in a higher utilization of the system if the package is designed not only for the product and its requirements but also for an automated handling system with different types of grasping devices. A decision support system is being developed to help the package designer select the most appropriate material and design to satisfy the requirements of the automated materials handling process. The decision support system is programmed in C++ which gives the flexibility and portability needed for this type of system. The user interface is using graphics to ease the understanding of different design options during the selection process.

  2. Application of combinatorial approach in packaging material selection

    Science.gov (United States)

    Jarupan, Lerpong; Kamarthi, Sagar V.; Gupta, Surendra M.

    2004-12-01

    Packaging material selection (PMS) problems have always been important to packaging designers and engineers. Not only does the selection of packaging material determine the costs and the environmental impacts of packaging, but also influences packaging physical characteristics and associated manufacturing methods. In order to reduce economic and environmental impacts, one has to take a holistic approach to packaging material selection by considering material effects throughout the packaging life cycle. To evaluate economic costs and environmental impacts both quantitative factors and subjective criteria play an important role in the packaging design. In the present work, fuzzy set theory is used for representing and manipulating the vague and subjective descriptions of packaging performance and design attributes. Further a genetic algorithm based approach is used for addressing the packaging material selection problem through multiple criteria decision-making. The overall approach comprises of two phases. In the first phase, fuzzy set theory is used for the linguistic transformation of performance attributes into numerical values. It results in a decision matrix that contains crisp scores. Also in this phase, a weight is assigned to each sub-criterion to show its importance compared to others. In the second phase, a GA is used to globally search for near-optimal or optimal design solutions. The implementation of the proposed methodology is illustrated through a numerical example.

  3. Package Formats for Preserved Digital Material

    DEFF Research Database (Denmark)

    Zierau, Eld

    2012-01-01

    This paper presents an investigation of the best suitable package formats for long term digital preservation. The choice of a package format for preservation is crucial for future access, thus a thorough analysis of choice is important. The investigation presented here covers setting up requireme...

  4. Package Formats for Preserved Digital Material

    DEFF Research Database (Denmark)

    Zierau, Eld

    2012-01-01

    This paper presents an investigation of the best suitable package formats for long term digital preservation. The choice of a package format for preservation is crucial for future access, thus a thorough analysis of choice is important. The investigation presented here covers setting up requireme......This paper presents an investigation of the best suitable package formats for long term digital preservation. The choice of a package format for preservation is crucial for future access, thus a thorough analysis of choice is important. The investigation presented here covers setting up...... the listed requirements will ensure mitigating a number of risks of information loss. Thus WARC is the best choice for a package format in cases where these same risks are judged most important. Similar analysis will need to be carried out in cases where the requirements differ from the ones described here...

  5. Application of Dispersive Liquid-liquid Microextraction to Dissolution of PAEs in Plastic Packaging Materials Under Acid Simulation System%分散液液微萃取在酸性模拟体系中塑料包装材料PAEs的溶出应用

    Institute of Scientific and Technical Information of China (English)

    刘芃岩; 李冰; 李睿; 王有旺; 陈晓景

    2011-01-01

    A effective, rapid, simple and convenient method, dispersive liquid-liquid microextraction (DLLME) combination gas chromatography coupled with flame ionization detector(GC-FID), was used for the determination of six phthalate esters (PAEs) in plastic packaging materials which was soaked in acid simulation system (3% acetic acid liquid). Under the optimum extraction conditions (carbon tetrachloride as extraction solvent, acetonitrile as dispersive solvent), a good linear relationship was obtained in the range of 1.0 - 100.0 μg/L, the correlation coefficients was 0. 999 8 - 0. 999 9 and the limits of detection was between 1.5- 15 μg/kg(S/N = 3). The PAEs in plastic packaging materials were successfully analyzed by using the proposed method under acid simulative system condition. The influencing factors of dissolving PAEs from plastic packaging materials, such as storage time, heating temperature, heating time and microwave heating, were researched. The recoveries, which had been spiked with different levels, fell in the range of 72.9% - 113.7% and the relative standard deviations were between 1.9% and 12.6%.%将分散液液微萃取(DLLME)与气相色谱-氢火焰离子化检测器(GC-FID)技术相结合,建立了一种简单快速测定塑料包装材料在酸性模拟体系(体积分数为3%乙酸水溶液)中6种邻苯二甲酸酯(PAEs)溶出量的方法.采用四氯化碳作萃取荆,乙腈为分散剂,在优化条件下,6种PAEs在1.0~100.0μg/L质量浓度内呈良好的线性关系,线性相关系数为0.999 8~0.999 9,检出限为1.5~15μg/kg(S/N=3).并考察了自然放置时间、加热温度、加热时间及微波对于塑料包装材料中PAEs溶出的影响,加标回收率72.9%~113.7%,相对标准偏差1.9%~12.6%.

  6. Recent innovations in edible and/or biodegradable packaging materials.

    Science.gov (United States)

    Guilbert, S; Cuq, B; Gontard, N

    1997-01-01

    Certain newly discovered characteristics of natural biopolymers should make them a choice material to be used for different types of wrappings and films. Edible and/or biodegradable packagings produced from agricultural origin macromolecules provide a supplementary and sometimes essential means to control physiological, microbiological, and physicochemical changes in food products. This is accomplished (i) by controlling mass transfers between food product and ambient atmosphere or between components in heterogeneous food product, and (iii) by modifying and controlling food surface conditions (pH, level of specific functional agents, slow release of flavour compounds), it should be stressed that the material characteristics (polysaccharide, protein, or lipid, plasticized or not, chemically modified or not, used alone or in combination) and the fabrication procedures (casting of a film-forming solution, thermoforming) must be adapted to each specific food product and usage condition (relative humidity, temperature). Some potential uses of these materials (e.g. wrapping of various fabricated foods; protection of fruits and vegetables by control of maturation; protection of meat and fish; control of internal moisture transfer in pizzas), which are hinged on film properties (e.g. organoleptic, mechanical, gas and solute barrier) are described with examples.

  7. DESIGNING OF POLYMERIC PACKAGING FILM MATERIALS WITH THE BARRIER PROPERTIES

    OpenAIRE

    Колосов, Олександр Євгенович; Сідоров, Дмитро Едуардович; Малецький, Сергій Віталійович

    2016-01-01

    The basic types of interactions for packaged food product and packaging that may occur between the polymer film packaging material and the produc are analyzed. It is noted that the most simple to implement isolation of the internal space of the polymer film packaging from the environment. In this package of the insulated space can be removed by air, in particular, evacuation, or replaced with an inert gas or inert gas mixture. It is noted that the permeability of gases and gas mixtures by non...

  8. 75 FR 75157 - Importation of Wood Packaging Material From Canada

    Science.gov (United States)

    2010-12-02

    .... 319.40-3 of the regulations lists the IPPC requirements, which include either heat treatment or... of Wood Packaging Material From Canada AGENCY: Animal and Plant Health Inspection Service, USDA... unmanufactured wood articles to remove the exemption that allows wood packaging material from Canada to enter...

  9. 19 CFR 10.601 - Retail packaging materials and containers.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 1 2010-04-01 2010-04-01 false Retail packaging materials and containers. 10.601...-Central America-United States Free Trade Agreement Rules of Origin § 10.601 Retail packaging materials and... for retail sale, if classified with the good for which preferential tariff treatment under the...

  10. Independent components analysis coupled with 3D-front-face fluorescence spectroscopy to study the interaction between plastic food packaging and olive oil.

    Science.gov (United States)

    Kassouf, Amine; El Rakwe, Maria; Chebib, Hanna; Ducruet, Violette; Rutledge, Douglas N; Maalouly, Jacqueline

    2014-08-11

    Olive oil is one of the most valued sources of fats in the Mediterranean diet. Its storage was generally done using glass or metallic packaging materials. Nowadays, plastic packaging has gained worldwide spread for the storage of olive oil. However, plastics are not inert and interaction phenomena may occur between packaging materials and olive oil. In this study, extra virgin olive oil samples were submitted to accelerated interaction conditions, in contact with polypropylene (PP) and polylactide (PLA) plastic packaging materials. 3D-front-face fluorescence spectroscopy, being a simple, fast and non destructive analytical technique, was used to study this interaction. Independent components analysis (ICA) was used to analyze raw 3D-front-face fluorescence spectra of olive oil. ICA was able to highlight a probable effect of a migration of substances with antioxidant activity. The signals extracted by ICA corresponded to natural olive oil fluorophores (tocopherols and polyphenols) as well as newly formed ones which were tentatively identified as fluorescent oxidation products. Based on the extracted fluorescent signals, olive oil in contact with plastics had slower aging rates in comparison with reference oils. Peroxide and free acidity values validated the results obtained by ICA, related to olive oil oxidation rates. Sorbed olive oil in plastic was also quantified given that this sorption could induce a swelling of the polymer thus promoting migration.

  11. Application of fluidization to separate packaging waste plastics.

    Science.gov (United States)

    Carvalho, M Teresa; Ferreira, Célia; Portela, Antía; Santos, João Tiago

    2009-03-01

    The objective of the experimental work described in this paper is the study of the separation of PS (polystyrene) from PET (polyethylene terephthalate) and PVC (polyvinyl chloride) from drop-off points using a fluidized bed separator. This is a low-cost process commonly used in the hydro-classification of mineral ores. Firstly, experimental tests were carried out with artificial granulated samples with different grain sizes, types and sources of plastic ("separability tests"). The particle settling velocities were determined under different operating conditions. Then, based on the results, the laboratory tests continued with real mixtures of waste plastics ("separation tests") and the efficiency of the process was evaluated. From a PET-rich mixture, a concentrate of PS with a 75% grade in PS was produced while the underflow was quite clear from PS (grade less than 0.5% in PS).

  12. THERMAL PERFORMANCE OF RADIOACTIVE MATERIAL PACKAGES IN TRANSPORT CONFIGURATION

    Energy Technology Data Exchange (ETDEWEB)

    Gupta, N.

    2010-03-04

    Drum type packages are routinely used to transport radioactive material (RAM) in the U.S. Department of Energy (DOE) complex. These packages are designed to meet the federal regulations described in 10 CFR Part 71. The packages are transported in specially designed vehicles like Safe Secure Transport (SST) for safety and security. In the transport vehicles, the packages are placed close to each other to maximize the number of units in the vehicle. Since the RAM contents in the packagings produce decay heat, it is important that they are spaced sufficiently apart to prevent overheating of the containment vessel (CV) seals and the impact limiter to ensure the structural integrity of the package. This paper presents a simple methodology to assess thermal performance of a typical 9975 packaging in a transport configuration.

  13. Modeling plasticity of materials with nanostructure

    Science.gov (United States)

    Kudinova, N. R.

    2017-02-01

    A new approach to modeling of the plasticity of materials with the particle size in the range from 3 to 20 nm (nanostructure) has been proposed. It is based on classical thermodynamic approach employing the surface tension of nanoparticles. Its main advantage is the minimum number of physical parameters in use. In the context of the proposed model, we calculated the dependence of the melting temperature on the nanoparticle size which is consistent with experimental data. The volume density of the surface energy of nanoparticles was also determined. This energy is assumed to be a significant part of the internal energy during deformation Yield point was interpreted as the result of changes of grains surface energy during the deformation. The obtained yield point dependence on the grain size was related to the Hall–Petch law, and this resulted in confirmation of the hypothesis on the crucial role of surface tension forces in the initial stage of plastic deformation of nanomaterials.

  14. Estimation of packaged water consumption and associated plastic waste production from household budget surveys

    Science.gov (United States)

    Wardrop, Nicola A.; Dzodzomenyo, Mawuli; Aryeetey, Genevieve; Hill, Allan G.; Bain, Robert E. S.; Wright, Jim

    2017-08-01

    Packaged water consumption is growing in low- and middle-income countries, but the magnitude of this phenomenon and its environmental consequences remain unclear. This study aims to quantify both the volumes of packaged water consumed relative to household water requirements and associated plastic waste generated for three West African case study countries. Data from household expenditure surveys for Ghana, Nigeria and Liberia were used to estimate the volumes of packaged water consumed and thereby quantify plastic waste generated in households with and without solid waste disposal facilities. In Ghana, Nigeria and Liberia respectively, 11.3 (95% confidence interval: 10.3-12.4), 10.1 (7.5-12.5), and 0.38 (0.31-0.45) Ml day-1 of sachet water were consumed. This generated over 28 000 tonnes yr-1 of plastic waste, of which 20%, 63% and 57% was among households lacking formal waste disposal facilities in Ghana, Nigeria and Liberia respectively. Reported packaged water consumption provided sufficient water to meet daily household drinking-water requirements for 8.4%, less than 1% and 1.6% of households in Ghana, Nigeria and Liberia respectively. These findings quantify packaged water’s contribution to household water needs in our study countries, particularly Ghana, but indicate significant subsequent environmental repercussions.

  15. An econometric analysis of regional differences in household waste collection: the case of plastic packaging waste in Sweden.

    Science.gov (United States)

    Hage, Olle; Söderholm, Patrik

    2008-01-01

    The Swedish producer responsibility ordinance mandates producers to collect and recycle packaging materials. This paper investigates the main determinants of collection rates of household plastic packaging waste in Swedish municipalities. This is done by the use of a regression analysis based on cross-sectional data for 252 Swedish municipalities. The results suggest that local policies, geographic/demographic variables, socio-economic factors and environmental preferences all help explain inter-municipality collection rates. For instance, the collection rate appears to be positively affected by increases in the unemployment rate, the share of private houses, and the presence of immigrants (unless newly arrived) in the municipality. The impacts of distance to recycling industry, urbanization rate and population density on collection outcomes turn out, though, to be both statistically and economically insignificant. A reasonable explanation for this is that the monetary compensation from the material companies to the collection entrepreneurs vary depending on region and is typically higher in high-cost regions. This implies that the plastic packaging collection in Sweden may be cost ineffective. Finally, the analysis also shows that municipalities that employ weight-based waste management fees generally experience higher collection rates than those municipalities in which flat and/or volume-based fees are used.

  16. THERMAL UPGRADING OF 9977 RADIOACTIVE MATERIAL (RAM) TYPE B PACKAGE

    Energy Technology Data Exchange (ETDEWEB)

    Gupta, N.; Abramczyk, G.

    2012-03-26

    The 9977 package is a radioactive material package that was originally certified to ship Heat Sources and RTG contents up to 19 watts and it is now being reviewed to significantly expand its contents in support of additional DOE missions. Thermal upgrading will be accomplished by employing stacked 3013 containers, a 3013 aluminum spacer and an external aluminum sleeve for enhanced heat transfer. The 7th Addendum to the original 9977 package Safety Basis Report describing these modifications is under review for the DOE certification. The analyses described in this paper show that this well-designed and conservatively analyzed package can be upgraded to carry contents with decay heat up to 38 watts with some simple design modifications. The Model 9977 package has been designed as a replacement for the Department of Transportation (DOT) Fissile Specification 6M package. The 9977 package is a very versatile Type B package which is certified to transport and store a wide spectrum of radioactive materials. The package was analyzed quite conservatively to increase its usefulness and store different payload configurations. Its versatility is evident from several daughter packages such as the 9978 and H1700, and several addendums where the payloads have been modified to suit the Shipper's needs without additional testing.

  17. An in-mold packaging process for plastic fluidic devices.

    Science.gov (United States)

    Yoo, Y E; Lee, K H; Je, T J; Choi, D S; Kim, S K

    2011-01-01

    Micro or nanofluidic devices have many channel shapes to deliver chemical solutions, body fluids or any fluids. The channels in these devices should be covered to prevent the fluids from overflowing or leaking. A typical method to fabricate an enclosed channel is to bond or weld a cover plate to a channel plate. This solid-to-solid bonding process, however, takes a considerable amount of time for mass production. In this study, a new process for molding a cover layer that can enclose open micro or nanochannels without solid-to-solid bonding is proposed and its feasibility is estimated. First, based on the design of a model microchannel, a brass microchannel master core was machined and a plastic microchannel platform was injection-molded. Using this molded platform, a series of experiments was performed for four process or mold design parameters. Some feasible conditions were successfully found to enclosed channels without filling the microchannels for the injection molding of a cover layer over the plastic microchannel platform. In addition, the bond strength and seal performance were estimated in a comparison with those done by conventional bonding or welding processes.

  18. Study on Migration of Melamine from Food Packaging Materials on Markets

    Institute of Scientific and Technical Information of China (English)

    JIE LU; JING XIAO; DA-JIN YANG; ZHU-TIAN WANG; DING-GUO JIANG; CONG-RONG FANG; JIE YANG

    2009-01-01

    Objectives To study the migration of melamine into foods from plastic food packaging materials and dairy product containers commonly used in China. Methods 37 samples were collected from the market. The EU migration testing conditions were adopted with distilled water, 3% acetic acid, n-hexane and 15% ethanol being chosen as the simulating solutions. The HPLC method was used to detect melamine. Results No melamine was detected in 15 dairy product containers. Among the 22 plastic samples, 16 of polypropylene, and polycarbonate types had no delectable amount melamine while a low level of melamine was found in 3 of the 6 melamine resin containers. Conclusion Migration of melamine from food packaging materials in China market is in line with the requirements of EU.

  19. SOME ASPECTS REGARDING THE DEGREE OF CONSERVATION OF THE CREAM PACKAED IN PLASTIC MATERIALS

    Directory of Open Access Journals (Sweden)

    Ioana Rebenciuc

    2010-01-01

    Full Text Available The prolongation of the product shelf life is directly influenced by the quality of the relation established between thepacking method, package and product. In this situation, the package properties play a primary role in ensuring theprotection and preservation function. This paper’s purpose is to present and analyze cream and types of plastic foodpackage, in relation with the food product; plastic food package still being the most used for the packaging of diaryproducts.The cream packagings have been tested specifically: white polypropylene packagings and coloured sealingends as well. The security of food stuff packaging materials is based on the insurance of the fact that while coming intocontact with food, the unsafe chemical substances do not migrate into it. The substance quantity limit that can betransmitted to product must be determined and limited at a level that will not cause any changes in food stuff. Initiallyanalyses on the product as well as on the package have been made. Then, analyses at 7 day- intervals during a month ofstorage have been made.

  20. Standard Guide for Packaging Materials for Foods to Be Irradiated

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2009-01-01

    1.1 This guide provides a format to assist producers and users of food packaging materials in selecting materials that have the desirable characteristics for their intended use and comply with applicable standards or government authorizations. It outlines parameters that should be considered when selecting food-contact packaging materials intended for use during irradiation of prepackaged foods and it examines the criteria for fitness for their use. 1.2 This guide identifies known regulations and regulatory frameworks worldwide pertaining to packaging materials for holding foods during irradiation; but it does not address all regulatory issues associated with the selection and use of packaging materials for foods to be irradiated. It is the responsibility of the user of this guide to determine the pertinent regulatory issues in each country where foods are to be irradiated and where irradiated foods are distributed. 1.3 This guide does not address all of the food safety issues associated with the synergisti...

  1. Application of Digital Image Correlation to Measurement of Packaging Material Mechanical Properties

    Directory of Open Access Journals (Sweden)

    Jian-Wei Zhou

    2013-01-01

    Full Text Available Among various packaging materials, papers and polymer plastics are the most common due to their light weights, low costs, and other advantages. However, their mechanical properties are difficult to measure precisely because of their softness. To overcome the difficulty, a new measure instrument prototype is proposed based on an optical method known as the digital image correlation (DIC. Experiments are designed to apply the DIC to measure mechanical properties of flexible packaging materials, including the stress-strain relationship, the Poisson ratio, the coefficient of heat expansion, the creep deformation, and the top-pressure deformation of corrugated box. In addition, the low frequency vibration of package is simulated, and the vibration frequencies are measured by DIC. Results obtained in the experiments illustrate the advantages of the DIC over traditional methods: noncontact, no reinforced effect, high precision over entire area, wide measurement range, and good measurement stability.

  2. Effect of different types of plastic packaging films on the moisture and aflatoxin contents of pistachio nuts during storage.

    Science.gov (United States)

    Shakerardekani, Ahmad; Karim, Roselina

    2013-04-01

    Pistachio nut (Pistacia vera L.) is one of the popular tree nuts in the world. Proper selection of packaging materials is necessary to prevent absorption of moisture and aflatoxin formation which will influence the overall product quality and safety. This research is undertaken to study the effect of different type of flexible packaging films on the moisture and aflatoxin contents of whole pistachio nuts during storage at ambient temperature (22-28 °C) and relative humidity of 85-100%. Five types of plastic films tested were low density polyethylene (LDPE) which serves as the control, food-grade polyvinyl chloride (PVC), nylon (LDPE/PA), polyamide/polypropylene (PA/PP) and polyethylene terephthalate (PET). The moisture content and aflatoxin content of pistachio nuts were measured using oven drying method and HPLC, respectively. Sample were analysed at 0, 2, 4, 6, 8 and 10 months during the storage period. Results showed that there was an increase in moisture content with the increase in storage time of pistachio nuts. The increase in moisture content was associated with the aflatoxin level of pistachio nuts during storage time. All the packaging materials except LDPE delayed the moisture absorption and aflatoxin formation of the product. The most suitable packaging materials for maintaining the quality and safety of pistachio nuts is PET films followed by nylon, PA/PP and PVC. The shelf-life of pistachio can be extended from 2 months (Control) to 5 months when PET is used as the packaging material.

  3. Packaging and transportation of radioactive materials: summary program

    Energy Technology Data Exchange (ETDEWEB)

    None

    1978-01-01

    This document contains summaries or abstracts of reports presented at the Symposium on Packaging and Transportation of Radioactive Materials. Separate indexing has been performed on individual items presented at this conference. (DC)

  4. Effects of two kinds of extraction solvent on detection of organic pollutants in plastic food packaging materials%两种萃取溶剂对塑料食品包装材料上有机污染物检测效果的影响

    Institute of Scientific and Technical Information of China (English)

    杨春莉; 杨春瑜; 金东升; 李丽; 安丽娟; 赫美

    2014-01-01

    Objective To observe the effect of the two kinds of extraction solvent on the detection of organic pollutants in plastic food packaging materials. Methods The residual contaminants were extracted by n-hexane and ethanol from plastic food packaging materials under ultrasonic condition, concentrated by rotary evaporator, and finally analyzed by gas chromatography-mass spectrometry (GC-MS). Results 2,6-di-tert-butyl-4-methylphenol (BHT), plasticizer dibutyl phthalate (DBP) and n-hexadecane solvents in printing ink were obtained using n-hexane as extraction solvent. While antioxidants 2,6-di-tert-butyl-4-methylphenol (BHT), n-hexadecane and n-eicosane were obtained using ethanol as extraction solvent. Conclusion The extraction effect using n-hexane as extraction solvent is better than that using ethanol as the extraction solvent.%目的:检测两种萃取溶剂对塑料食品包装材料上有机污染物检测效果的影响。方法分别以正己烷和无水乙醇为萃取溶剂对塑料食品包装材料上污染物进行超声提取,提取后用旋转蒸发浓缩,最后采用气相色谱-质谱联机(GC-MS)分析方法以离子化方式对浓缩的污染物进行表征。结果正己烷作为萃取溶剂能萃取出抗氧化剂2,6-二叔丁基对甲酚、增塑剂邻苯二甲酸二丁酯、油墨生产中所用的溶剂正十六烷;乙醇作为萃取溶剂能萃取出抗氧化剂2,6-二叔丁基对甲酚、油墨生产中所用的溶剂正十六烷和正二十烷。结论正己烷作为萃取溶剂的提取效果要比乙醇作为萃取溶剂提取效果好。

  5. Chitosan coatings onto polyethylene terephthalate for the development of potential active packaging material

    Energy Technology Data Exchange (ETDEWEB)

    Zemljic, Lidija Fras, E-mail: lidija.fras@uni-mb.si [Laboratory for Characterization and Processing of Polymers, Faculty of Mechanical Engineering, University of Maribor, Smetanova 17, 2000 Maribor (Slovenia); Tkavc, Tina [Laboratory for Characterization and Processing of Polymers, Faculty of Mechanical Engineering, University of Maribor, Smetanova 17, 2000 Maribor (Slovenia); Vesel, Alenka [Jozef Stefan Institute, Jamova 39, 1000 Ljubljana (Slovenia); Sauperl, Olivera [Laboratory for Characterization and Processing of Polymers, Faculty of Mechanical Engineering, University of Maribor, Smetanova 17, 2000 Maribor (Slovenia)

    2013-01-15

    Highlights: Black-Right-Pointing-Pointer The adsorption/desorption of chitosan onto PET plastic film was studied. Black-Right-Pointing-Pointer Chitosan was reversible attached onto PET plastic films. Black-Right-Pointing-Pointer Antimicrobial functionalized PET may provide potential active packaging material. - Abstract: In this paper advanced surface treatment of PET plastic film is presented for introduction of antimicrobial properties as a potential application for food (as for example meat) packaging material. Adsorption/desorption of chitosan onto PET plastic film surface was studied using several analytical techniques such as: X-Ray Photoelectron Spectroscopy (XPS), ATR-FTIR spectroscopy and titrations. Kinetic desorption of chitosan from PET surface was analysed by polyelectrolyte titration and spectrophotometric Ninhydrine reaction. Standard antimicrobial test ASTM E2149-01 was performed for functionalised PET materials in order to determine their antimicrobial properties; i. e. to measure the reductions of some of the meat pathogens; such as bacteria Salmonella enterica, Campylobacter spp., Escherichia coli, Listeria monocytogenes and fungi Candida albicans.

  6. Applying and influence of polymer materials for packaging dairy beverages

    Directory of Open Access Journals (Sweden)

    Milanović Spasenija D.

    2017-01-01

    Full Text Available Functional food is positioned above the traditional, with the potential to improve human health. Thanks to very good physico-mechanical and barrier properties polymers became very popular in food industry as a packaging materials. Wild range of fermented dairy products could be packed in this packaging materials according to their’s inertness as well. Functional milk beverage was obtained from milk with 0,9% milk fat content by applying 10% v/v of kombucha’s inoculum cultivated on a black tea sweetened with sucrose. The beverage was packed in a different packaging materials: polyamid-polyethylen (PA/PE coextruded foil bags and polyprophylen (PP cups closed with aluminium (Al foil lids under atmospheric conditions (ATM. Beverages were storaged for 15 days at 4°C. The quality of kombucha inoculum, milk and obtained kombucha fermented milk beverage were analysed. Characterization of the packaging materials was done by investigating physico-mechanical, barrier and structural properties. The composition and changes in the headspace atmosphere, after production and during the storage, were analysed. The influence of packaging material properties and packaging conditions on the biochemical transformations of the milk’s components (the content of: lactose, L-lactic acid, D-galactose, ethanol, B1 and B2 vitamins influenced by kombucha starter were analysed as well. On the bases of the obtained results of characterisation of packaging materials, it can be concluded that PA/PE and PP materials are proper to be used for analysed beverage’s packaging. Also, there is no significant difference in content of components which were quantified, between analysed materials in correlation with the packed fermented milk beverage. [Projekat Ministarstva nauke Republike Srbije, br. III-46009

  7. Extending the utility of a radioactive material package

    Energy Technology Data Exchange (ETDEWEB)

    Abramczyk, G. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL). Savannah River Nuclear Solutions; Nathan, S. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River Nuclear Solutions; Loftin, B. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL). Savannah River Nuclear Solutions; Bellamy, S. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL). Savannah River Nuclear Solutions

    2015-06-04

    Once a package has been certified for the transportation of DOT Hazard Class 7 – Radioactive Material in compliance with the requirements of 10 CFR 71, it is often most economical to extend its utility through the addition of content-specific configuration control features or the addition of shielding materials. The SRNL Model 9977 Package’s authorization was expanded from its original single to twenty contents in this manner; and most recently, the 9977 was evaluated for a high-gamma source content. This paper discusses the need for and the proposed shielding modifications to the package for extending the utility of the package for this purpose.

  8. Extending the utility of a radioactive material package

    Energy Technology Data Exchange (ETDEWEB)

    Abramczyk, G. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL). Savannah River Nuclear Solutions; Nathan, S. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River Nuclear Solutions; Loftin, B. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL). Savannah River Nuclear Solutions; Bellamy, S. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL). Savannah River Nuclear Solutions

    2015-06-04

    Once a package has been certified for the transportation of DOT Hazard Class 7 – Radioactive Material in compliance with the requirements of 10 CFR 71, it is often most economical to extend its utility through the addition of content-specific configuration control features or the addition of shielding materials. The SRNL Model 9977 Package’s authorization was expanded from its original single to twenty contents in this manner; and most recently, the 9977 was evaluated for a high-gamma source content. This paper discusses the need for and the proposed shielding modifications to the package for extending the utility of the package for this purpose.

  9. Recent advances in biopolymers and biopolymer-based nanocomposites for food packaging materials.

    Science.gov (United States)

    Tang, X Z; Kumar, P; Alavi, S; Sandeep, K P

    2012-01-01

    Plastic packaging for food and non-food applications is non-biodegradable, and also uses up valuable and scarce non-renewable resources like petroleum. With the current focus on exploring alternatives to petroleum and emphasis on reduced environmental impact, research is increasingly being directed at development of biodegradable food packaging from biopolymer-based materials. The proposed paper will present a review of recent developments in biopolymer-based food packaging materials including natural biopolymers (such as starches and proteins), synthetic biopolymers (such as poly lactic acid), biopolymer blends, and nanocomposites based on natural and synthetic biopolymers. The paper will discuss the various techniques that have been used for developing cost-effective biodegradable packaging materials with optimum mechanical strength and oxygen and moisture barrier properties. This is a timely review as there has been a recent renewed interest in research studies, both in the industry and academia, towards development of a new generation of biopolymer-based food packaging materials with possible applications in other areas.

  10. Packaging configurations and handling requirements for nuclear materials

    Energy Technology Data Exchange (ETDEWEB)

    Jefferson, R.M.

    1981-01-01

    The basic safety concepts for radioactive material are that the package is the primary protection for the public, that the protection afforded by the package should be proportional to the hazard and that the package must be proved by performance. These principles are contained in Department of Energy (DOE), Nuclear Regulatory Commission (NRC) and Department of Transportation (DOT) regulations which classify hazards of various radioactive materials and link packaging requirements to the physical form and quantities being shipped. Packaging requirements are reflected in performance standards to guarantee that shipments of low hazard quantities will survive the rigors of normal transportation and that shipments of high hazard quantities will survive extreme severity transportation accidents. Administrative controls provide for segregation of radioactive material from people and other sensitive or hazardous material. They also provide the necessary information function to control the total amounts in a conveyance and to assure that appropriate emergency response activities be started in case of accidents or other emergencies. Radioactive materials shipped in conjunction with the nuclear reactor programs include, ores, concentrates, gaseous diffusion feedstocks, enriched and depleted uranium, fresh fuel, spent fuel, high level wastes, low level wastes and transuranic wastes. Each material is packaged and shipped in accordance with regulations and all hazard classes, quantity limits and packaging types are called into use. From the minimal requirements needed to ship the low hazard uranium ores or concentrates to the very stringent requirements in packaging and moving high level wastes or spent fuel, the regulatory system provides a means for carrying out transportation of radioactive material which assures low and controlled risk to the public.

  11. An Elastic Plastic Contact Model with Strain Hardening for the LAMMPS Granular Package

    Energy Technology Data Exchange (ETDEWEB)

    Kuhr, Bryan [Virginia Polytechnic Inst. and State Univ. (Virginia Tech), Blacksburg, VA (United States); Brake, Matthew Robert [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Component Science and Mechanics; Lechman, Jeremy B. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Nanoscale and Reactive Processes

    2015-03-01

    The following details the implementation of an analytical elastic plastic contact model with strain hardening for normal im pacts into the LAMMPS granular package. The model assumes that, upon impact, the co llision has a period of elastic loading followed by a period of mixed elastic plas tic loading, with contributions to each mechanism estimated by a hyperbolic seca nt weight function. This function is implemented in the LAMMPS source code as the pair style gran/ep/history. Preliminary tests, simulating the pouring of pure nickel spheres, showed the elastic/plastic model took 1.66x as long as similar runs using gran/hertz/history.

  12. CORROSION OF LEAD SHIELDING IN NUCLEAR MATERIALS PACKAGES

    Energy Technology Data Exchange (ETDEWEB)

    Subramanian, K; Kerry Dunn, K; Joseph Murphy, J

    2008-07-18

    Inspection of United States-Department of Energy (US-DOE) model 9975 nuclear materials shipping package revealed corrosion of the lead shielding that was induced by off-gas constituents from organic components in the package. Experiments were performed to determine the corrosion rate of lead when exposed to off-gas or degradation products of these organic materials. The results showed that the room temperature vulcanizing (RTV) sealant was the most corrosive organic species used in the construction of the packaging, followed by polyvinyl acetate (PVAc) glue. Fiberboard material, also used in the construction of the packaging induced corrosion to a much lesser extent than the PVAc glue and RTV sealant, and only in the presence of condensed water. The results indicated faster corrosion at temperatures higher than ambient and with condensed water. In light of these corrosion mechanisms, the lead shielding was sheathed in a stainless steel liner to mitigate against corrosion.

  13. Eco-efficiency in Recycling Systems: Evaluation Methods & Case Studies for Plastic Packaging

    OpenAIRE

    Eik, Arne; Steinmo, Solveig; Solem, Håvard; Brattebø, Helge; Saugen, Bernt

    2002-01-01

    Focus on the so-called waste hierarchy, which claims that the prevention of waste is the most environmental friendly option, followed by reuse, remanufacturing, mechanical recycling, feedstock recycling, energy recovery, incineration and landfill, is considered to be an important strategy towards sustainable development. Increased use of plastic packaging for various products and the corresponding increase in waste generated are important challenges that must be dealt with from a waste-hierar...

  14. Influence of lubricant oil residual fraction on recycled high density polyethylene properties and plastic packaging reverse logistics proposal

    Directory of Open Access Journals (Sweden)

    Harley Moraes Martins

    2015-10-01

    Full Text Available Abstract To recycle post-consumer HDPE contaminated with waste lubricating oils, companies include prior washing and drying in the process. This consumes large amounts of water and energy, generates significant effluent requiring treatment. This study assesses lubricating oil influence on HDPE properties to evaluate the feasibility of its direct mechanical recycling without washing. The current lubricating oil packaging reverse logistics in Rio de Janeiro municipality is also analyzed. HDPE bottle samples were processed with seven oil contents ranging from 1.6-29.4 (wt%. The results indicated the possibility to reprocess the polymer with oily residue not exceeding 3.2%. At higher levels, the external oil lubricating action affects the plastic matrix processing in the extruder and injection, and the recycled material has a burnt oil odor and free oil on the surface. Small residual oil amounts retain the plastic properties comparable to the washed recycled polymer and exhibited benefits associated with the oil plasticizer action. However, oil presence above 7.7% significantly changes the properties and reduces the elasticity and flexural modulus and the plastic matrix crystallinity.

  15. Evaluation of Standard Loose Plastic Packaging for the Management of Rhyzopertha dominica (F.) (Coleoptera: Bostrichidae) and Tribolium castaneum (Herbst) (Coleoptera: Tenebriondiae).

    Science.gov (United States)

    Hassan, Muhammad Waqar; Gulraize; Ali, Usman; Ur Rehman, Fazal; Najeeb, Hafsa; Sohail, Maryam; Irsa, Bakhtawar; Muzaffar, Zubaria; Chaudhry, Muhammad Shafiq

    2016-01-01

    Three standard foodstuff plastic packaging namely polyethylene (PE), polypropylene (PP), and polyvinylchloride (PVC) were evaluated for management of lesser grain borer Rhyzopertha dominica (F.) (Coleoptera: Bostrichidae) and red flour beetle Tribolium castaneum (Herbst) (Coleoptera: Tenebrionidae). Resistance parameters in packaging were recorded as punctures, holes, penetrations, sealing defects, and invasions with two thicknesses and tested for two lengths of time. Damages like punctures, holes and penetrations by both insects were more in PE packaging however R. dominica made more penetrations in PP than in PE. For both insects sealing defects and invasions were predominant in PVC than in others. Thickness did not affect significantly damage types but significantly more holes and penetrations by R. dominica were in less thickness. Punctures and holes by R. dominica were more after less time period but other damages in packaging were more after more time period. However for T. castaneum all sorts of damages were seen more after more time period. Overall categorization between two insects showed R. dominica made more penetrations and T. castaneum made more invasions compared with their counterparts. Pictures were taken under camera fitted microscope to magnify punctures and holes in different packaging and thicknesses. Insect mortality due to phosphine was more in PP and PE packaging and least in PVC packaging and thickness effect was marginal. T. castaneum mortality was significantly more after 48 h than after 24 h. Damages extent in packaging and fumigation results showed PP to be the best of three packaging materials to manage these insects.

  16. Evaluation of Standard Loose Plastic Packaging for the Management of Rhyzopertha dominica (F.) (Coleoptera: Bostrichidae) and Tribolium castaneum (Herbst) (Coleoptera: Tenebriondiae)

    Science.gov (United States)

    Hassan, Muhammad Waqar; Gulraize; Ali, Usman; Ur Rehman, Fazal; Najeeb, Hafsa; Sohail, Maryam; Irsa, Bakhtawar; Muzaffar, Zubaria; Chaudhry, Muhammad Shafiq

    2016-01-01

    Three standard foodstuff plastic packaging namely polyethylene (PE), polypropylene (PP), and polyvinylchloride (PVC) were evaluated for management of lesser grain borer Rhyzopertha dominica (F.) (Coleoptera: Bostrichidae) and red flour beetle Tribolium castaneum (Herbst) (Coleoptera: Tenebrionidae). Resistance parameters in packaging were recorded as punctures, holes, penetrations, sealing defects, and invasions with two thicknesses and tested for two lengths of time. Damages like punctures, holes and penetrations by both insects were more in PE packaging however R. dominica made more penetrations in PP than in PE. For both insects sealing defects and invasions were predominant in PVC than in others. Thickness did not affect significantly damage types but significantly more holes and penetrations by R. dominica were in less thickness. Punctures and holes by R. dominica were more after less time period but other damages in packaging were more after more time period. However for T. castaneum all sorts of damages were seen more after more time period. Overall categorization between two insects showed R. dominica made more penetrations and T. castaneum made more invasions compared with their counterparts. Pictures were taken under camera fitted microscope to magnify punctures and holes in different packaging and thicknesses. Insect mortality due to phosphine was more in PP and PE packaging and least in PVC packaging and thickness effect was marginal. T. castaneum mortality was significantly more after 48 h than after 24 h. Damages extent in packaging and fumigation results showed PP to be the best of three packaging materials to manage these insects. PMID:27638958

  17. Assessment of environmental impact of ultraviolet radiation or electron beam cured print inks on plastic packaging materials; Avaliacao do impacto ambiental gerado por tintas graficas curadas por radiacao ultravioleta ou feixe de eletrons em materiais para embalagens plasticas convencionais ou biodegradaveis pos-consumo

    Energy Technology Data Exchange (ETDEWEB)

    Bardi, Marcelo Augusto Goncalves

    2014-07-01

    The high level of pollution generated by the inadequate disposal of polymeric materials has motivated the search for environmentally friendly systems and techniques such as the application of biodegradable polymers and the replacement of the solvent-based paint systems by those with high solids content, based water or cured by radiation, practically free of volatile organic compounds. However, the cured polymer coatings are neither soluble nor molten, increasing the complexity of the reprocessing, recycling and degradation. Thus, this work aimed to develop print inks modified with pro-degrading agents, cured by ultraviolet radiation or electron beam, for printing or decoration in plastic packaging products of short lifetime, which are biodegradable or not. Six coatings (varnish and inks in five colors: yellow, blue, white, black and red), three pro-degrading agents (cobalt stearate, cerium stearate and manganese stearate), five polymeric substrates (Ecobras®, low density polyethylene and its respective modifications with pro-degrading agents). The coatings were applied to the substrates and cured by ultraviolet radiation or electron beam, resulting in 180 samples. These materials were then exposed to accelerated aging chamber, type 'QUV', and composting in natural environment. In order to assess the effects of the polymer coatings on the degradation process of the specimens, only the yellow and black samples were exposed to a controlled composting environment via respirometry, reducing to 16 the number of samples. The organic compound generated by the biodegradation process was analyzed by the ecotoxicity tests. It was observed that the coating layer acted as a barrier that inhibits degradation of the plastic when exposed to weathering. The addition of pro-degrading agents promoted acceleration in the degradation process, promoting the migration of the metal ion to the medium without affecting the final quality of the organic compost. (author)

  18. Volatile Organic Contaminants From Plastic Packaging: Development And Validation Of Analytical Methods [contaminantes Voláteis Provenientes De Embalagens Plásticas: Desenvolvimento E Validação De Métodos Analíticos

    OpenAIRE

    Maria Teresa de Alvarenga Freire; Carla Beatriz Grespan Bottoli; Samanta Fabris; Felix Guillermo Reyes Reyes

    2008-01-01

    Plastic packaging materials intended for use in food packaging is an area of great interest from the scientific and economic point of view due to the irreversible internationalization and globalization process of food products. Nevertheless, a debate related to food safety aspects has emerged within the scientific community. Therefore, the development of analytical methods that allow identifying and quantifying chemical substances of toxicological potential in the packaging is considered esse...

  19. A study on the radiometric method for evaluating element migration from plastic packagings to its contents; Estudo do metodo radiometrico para avaliacao da migracao de elementos de embalagens plasticas para o seu conteudo

    Energy Technology Data Exchange (ETDEWEB)

    Soares, Eufemia Paez

    2008-07-01

    Over the past few years, problems related to food contamination by substances or elements that can be a risk to human health have became a concern, not only to government authorities, but to the general population as well. Within this context, plastic packaging can constitute a source of food contamination since plastic manufacturing processes involve the use of catalysts and different types of additives that may contain toxic elements. When food comes into contact with this packaging, components of the package may migrate to the food. In order to control the material used as food packaging, the National Health Surveillance Agency (ANVISA) in Brazil, has established boundary values of migrant substances and procedures to determine migration from plastic packagings to food. In this study the radiometric method was evaluated for element migration determination from plastic packaging to food simulating or to the food itself. This radiometric method consisted in irradiating plastic packaging samples with a thermal neutron flux from the IEA-R1 nuclear research reactor in order to produce radionuclides of elements present in the packagings. The irradiated plastic was then exposed to food simulant or food for element migration. Gamma ray spectrometry was used to measure radioactivity in the simulant or food in order to quantify the migration. The food simulating types and experimental conditions were established according to the ANVISA regulations. Element migration was studied for plastic packaging used for soft drinks, drinking water, milk, dairy products, juices and fatty foods. In the instrumental neutron activation analysis of these packagings the presence of As, Cd, Cr, Co and Sb II was verified. Results obtained from the migration experiments by the radiometric method indicated that Cd, Co, Cr and Sb present in these plastics migrated to the simulant or to the food. In some packagings, the migration of only some of these elements was observed. In these cases the

  20. Implications of material selection on the design of packaging machinery.

    Science.gov (United States)

    Merritt, J P

    2009-01-01

    Material selection has significant implications on the design and cost of horizontal-form-fill-seal packaging machinery. To avoid excessive costs, machine redesigns and project delays, material selection must be reconciled early in the project and revisited throughout the construction of the machine.

  1. Development of complementary HPLC-DAD/APCI MS methods for chemical characterization of pharmaceutical packaging materials.

    Science.gov (United States)

    Petruševski, V; Jolevska, S T; Ribarska, J T; Chachorovska, M; Petkovska, A; Ugarković, S

    2016-05-30

    The chemical characterization of plastics for pharmaceutical packaging has been subject to ever increasing regulatory scrutiny, the reasons for which being: a) plastic additives and degradation products can be extremely hazardous to the patients' health (especially patients on chronic therapy) and b) they offer no therapeutic or formulatory benefit whatsoever. The last decade has seen the issuing of several books, monographs and guidelines dealing with extractables and leachables, however the amount of scientific work done so far is still fairly small (the majority of it performed by only a few research groups), with only a small number of methods published in the literature. This work focuses on developing a set of two complementary HPLC-DAD/APCI MS methods for simultaneous separation, detection, identification and quantification of a wide variety of packaging additives and degradants, the second method specifically targeting a group of compounds known as polymeric hindered amine light stabilizers (HALS), which are known to be notoriously difficult to separate and analyze with standard analytical techniques. The methods are capable of detecting plastic additives present in low ppb concentrations, from samples extracted in solvents with various polarities and pH values. Both methods were developed and optimized using system suitability mixtures comprised of 9 additives commonly encountered in plastic materials, and their practical applicability tested on a variety of extracts from low-density polyethylene (LDPE) and polypropylene (PP), where several additives were successfully separated, detected and identified.

  2. CORROSION OF LEAD SHIELDING IN NUCLEAR MATERIALS PACKAGES

    Energy Technology Data Exchange (ETDEWEB)

    Subramanian, K; Kerry Dunn, K

    2007-11-16

    Inspection of United States-Department of Energy (US-DOE) model 9975 nuclear materials shipping package revealed corrosion of the lead shielding induced by off-gas constituents from organic components in the package. Experiments were performed to determine the corrosion rate of lead when exposed to off-gas or degradation products of these organic materials. The results showed that the room temperature vulcanizing (RTV) sealant was the most corrosive organic species followed by the polyvinyl acetate (PVAc) glue. The fiberboard material induced corrosion to a much lesser extent than the PVAc glue and RTV, and only in the presence of condensed water. The results indicated faster corrosion at temperatures higher than ambient and with condensed water as expected. A corrosion rate of 0.05 mm/year measured for coupons exposed to the most aggressive conditions was recommended as a conservative estimate for use in package performance calculations.

  3. Contaminantes voláteis provenientes de embalagens plásticas: desenvolvimento e validação de métodos analíticos Volatile organic contaminants from plastic packaging: development and validation of analytical methods

    Directory of Open Access Journals (Sweden)

    Maria Teresa de Alvarenga Freire

    2008-01-01

    Full Text Available Plastic packaging materials intended for use in food packaging is an area of great interest from the scientific and economic point of view due to the irreversible internationalization and globalization process of food products. Nevertheless, a debate related to food safety aspects has emerged within the scientific community. Therefore, the development of analytical methods that allow identifying and quantifying chemical substances of toxicological potential in the packaging is considered essential. This article focuses on the main analytical methods, including validation parameters, as well as extraction and quantification techniques for determination of volatile organic compounds from food packaging materials.

  4. Determination of plastic additives in packaging by liquid chromatography coupled to high resolution mass spectrometry.

    Science.gov (United States)

    Moreta, Cristina; Tena, María-Teresa

    2015-10-02

    A simple and sensitive analytical method for the determination of several plastic additives in multilayer packaging based on solid-liquid extraction (SLE) and ultra-high performance liquid chromatography (UHPLC) coupled to variable wavelength (VWD) and time of flight mass spectrometry (TOF-MS) detectors is presented. The proposed method allows the simultaneous determination of fourteen additives belonging to different families such as antioxidants, slip agents and light stabilizers, as well as two oxidation products in only 9min. The developed method was validated in terms of linearity, matrix effect error, detection and quantification limits, repeatability and intermediate precision. The instrumental method showed satisfactory repeatability and intermediate precision at concentrations closed to LOQ with RSDs less than 7 and 20%, respectively, and LODs until 5000 times more sensitive than other GC-FID and HPLC-VWD methods previously reported. Also, focused ultrasound solid-liquid extraction (FUSLE) was optimized and evaluated to extract plastic additives from packaging. Extraction results obtained by FUSLE and SLE were compared to those obtained by pressurized liquid extraction (PLE). All extraction methods showed excellent extraction efficiency for slip agents, however quantitative recovery of all analytes was achieved only by SLE with just 5ml of hexane for 10h. Finally, the selected method was applied to the analysis of packaging samples where erucamide, Irgafos 168, oxidized Irgafos 168, Irganox 1076 and Irganox 1010 were detected and quantified. Copyright © 2015 Elsevier B.V. All rights reserved.

  5. Attachment of Asaia bogorensis Originating in Fruit-Flavored Water to Packaging Materials

    Directory of Open Access Journals (Sweden)

    Dorota Kregiel

    2014-01-01

    Full Text Available The objective of this study was to investigate the adhesion of isolated spoilage bacteria to packaging materials used in the food industry. Microorganisms were isolated from commercial fruit-flavored mineral water in plastic bottles with flocks as a visual defect. The Gram-negative rods were identified using the molecular method through the amplification of a partial region of the 16S rRNA gene. Based on the sequence identity (99.6% between the spoilage organism and a reference strain deposited in GenBank, the spoilage isolate was identified as Asaia bgorensis. Experiments on bacterial adhesion were conducted using plates made of glass and polystyrene (packaging materials commonly used in the beverage industry. Cell adhesion ability was determined using luminometry, plate count, and the microscopic method. The strain of A. bogorensis was characterized by strong adhesion properties which were dependent on the surface type, with the highest cell adhesion detected on polystyrene.

  6. Development of more friendly food packaging materials base on polypropylene through blending with polylacticacid

    Science.gov (United States)

    Setiawan, Achmad Hanafi; Aulia, Fauzan

    2017-01-01

    The commonly food packaging materials today is used a thin layer plastic or film, which is made of a synthetic polymer, such as polypropylene (PP). However, the use of these polymers has a negative impact on the environment, because the synthetic polymer is difficult to degrade naturally by the biotic components such as micro-organisms decomposers and abiotic components such as the sunshine. The use of the biodegradable polymeric material will reduce the use of synthetic polymer products, thereby reducing plastic waste pollution at relatively low cost, it is expected to produce positive effects both for the environment and in terms of economy. PLA is a biodegradable polymer that can be substituted totally or partially to synthetic polymers as far as could fulfill the main function of packaging in the protection and preservation of food. Increasing PLA content in polypropylene blend will affect to the increasing in its water absorption and also its biodegradable. 20% PLA may the optimum composition of poly-blend for food packaging.

  7. Damage evolution of metallic materials during high temperature plastic deformation

    Institute of Scientific and Technical Information of China (English)

    汪凌云; 刘雪峰; 汤爱涛; 黄光杰

    2002-01-01

    The damage evolution of high temperature plastic deformation of metallic materials was studied by use of continuum damage mechanics (CDM) theory. Based on thermodynamics, on a damage variable D and Zener-Hollomon parameter Z, and on the effective stress concept, a damage evolution model of high temperature plastic deformation was derived and was used to analyze the damage evolution of 1420 Al-Li alloy during high temperature plastic deformation. The model that is verified by tests can also be applied to the materials that are loaded prorata or out of proportion during high temperature plastic deformation. It extends the applied scope of damage mechanics.

  8. Chitosan coatings onto polyethylene terephthalate for the development of potential active packaging material

    Science.gov (United States)

    Zemljič, Lidija Fras; Tkavc, Tina; Vesel, Alenka; Šauperl, Olivera

    2013-01-01

    In this paper advanced surface treatment of PET plastic film is presented for introduction of antimicrobial properties as a potential application for food (as for example meat) packaging material. Adsorption/desorption of chitosan onto PET plastic film surface was studied using several analytical techniques such as: X-Ray Photoelectron Spectroscopy (XPS), ATR-FTIR spectroscopy and titrations. Kinetic desorption of chitosan from PET surface was analysed by polyelectrolyte titration and spectrophotometric Ninhydrine reaction. Standard antimicrobial test ASTM E2149-01 was performed for functionalised PET materials in order to determine their antimicrobial properties; i. e. to measure the reductions of some of the meat pathogens; such as bacteria Salmonella enterica, Campylobacter spp., Escherichia coli, Listeria monocytogenes and fungi Candida albicans.

  9. Microbial Effects on Nuclear Waste Packaging Materials

    Energy Technology Data Exchange (ETDEWEB)

    Horn, J; Martin, S; Carrillo, C; Lian, T

    2005-07-22

    Microorganisms may enhance corrosion of components of planned engineered barriers within the proposed nuclear waste repository at Yucca Mountain (YM). Corrosion could occur either directly, through processes collectively known as Microbiologically Influenced Corrosion (MIC), or indirectly, by adversely affecting the composition of water or brines that come into direct contact with engineered barrier surfaces. Microorganisms of potential concern (bacteria, archea, and fungi) include both those indigenous to Yucca Mountain and those that infiltrate during repository construction and after waste emplacement. Specific aims of the experimental program to evaluate the potential of microorganisms to affect damage to engineered barrier materials include the following: Indirect Effects--(1) Determine the limiting factors to microbial growth and activity presently in the YM environment. (2) Assess these limiting factors to aid in determining the conditions and time during repository evolution when MIC might become operant. (3) Evaluate present bacterial densities, the composition of the YM microbial community, and determining bacterial densities if limiting factors are overcome. During a major portion of the regulatory period, environmental conditions that are presently extant become reestablished. Therefore, these studies ascertain whether biomass is sufficient to cause MIC during this period and provide a baseline for determining the types of bacterial activities that may be expected. (4) Assess biogenic environmental effects, including pH, alterations to nitrate concentration in groundwater, the generation of organic acids, and metal dissolution. These factors have been shown to be those most relevant to corrosion of engineered barriers. Direct Effects--(1) Characterize and quantify microbiological effects on candidate containment materials. These studies were carried out in a number of different approaches, using whole YM microbiological communities, a subset of YM

  10. Efeitos de diferentes teores de umidade e espessuras do material de embalagem plástica na conservação de sementes de amendoim Effects of different moisture contents and thickness of the plastic packaging material on the preservation of peanut seeds

    Directory of Open Access Journals (Sweden)

    Romeu de Tella

    1979-01-01

    Full Text Available Determinaram-se, aos 3, 6, 9, 12 e 18 meses de armazenamento, as porcentagens de germinação e umidade de sementes de amendoim do cultivar tatu, descascadas mecanicamente, com níveis iniciais de 5,2; 6,2; 7,0; 8,2 e 9,2% de umidade, acondicionadas em sacos de polietileno de 0,05; 0,08; 0,10 e 0,15mm de espessura e mantidas em uma sala em condições não controladas de temperatura e umidade relativa, por um período de 18 meses. As umidades iniciais de 8,2 e 9,2% foram prejudiciais à conservação das sementes, principalmente quando estas foram acondicionadas nos sacos plásticos de 0,15 ou 0,10mm de espessura. As melhores condições para a manutenção da germinação das sementes foram a secagem aos níveis de 5,2 ou 6,2% de umidade e acondicionamento nos sacos plásticos de 0,15 ou 0,10mm de espessura. As paredes dos sacos plásticos não impediram trocas de umidade entre o ambiente e as sementes, sendo que essas trocas foram mais rápidas nos sacos de menor espessura.Mecanically shelled peanut (Arachis hypogaea L. seeds of the cultivar tatu, with initial moisture contents of 5.2, 6.2, 7.0, 8.2, and 9.2%, and packaged in polyethylene bags of 0.05, 0.08, 0.10, and 0.15mm thick. were stored in a room with no temperature and relative humidity control, in Campinas, State of São Paulo. Germination and moisture content percentagens were determined at 3, 6, 9, 12, and 18 months storage. The initial moisture contents of 8.2 and 9.2% were damaging to the preservation of the seeds, mainly when these were packaged in the bags of 0.15 or 0.10mm thick. The best storage conditions were those provided by drying to 5.2 or 6.2% moisture levels, and packaging in 0.15 or 0.10 mm thick plastic bags. The walls of the plastic bags did not hamper moisture vapor transmission between environment and seeds. The transmission rates were higher in the bags of thinner walls.

  11. 49 CFR 173.428 - Empty Class 7 (radioactive) materials packaging.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Empty Class 7 (radioactive) materials packaging... SHIPPERS-GENERAL REQUIREMENTS FOR SHIPMENTS AND PACKAGINGS Class 7 (Radioactive) Materials § 173.428 Empty Class 7 (radioactive) materials packaging. A packaging which previously contained Class 7...

  12. Characteristics of meat packaging materials and their environmental suitability assessment

    Directory of Open Access Journals (Sweden)

    Šuput Danijela Z.

    2013-01-01

    Full Text Available After functional phase, packaging becomes waste that is recycled or disposed of in landfills. Recently, numerus packages have been developed for assessing the packaging risk on the environment. We applied Gabi 4 Education software on polymer product packaging for meat products. The objective of first part of the paper was characterization of materials used for meat and meat products packaging in terms of mechanical and barrier properties. Results show that tested materials are able to keep protective atmosphere and contribute to the quality and sustainability of the product. Air permeability was 3.60 and 26.60 ml/m224h, and water vapor was 6.90 and 9.50 ml/m224h, respectively, for foils 1 and 2, as a result of different film composition. In second part, based on real data, Gabi 4 Education software is applied. The obtained results showed that organic compounds emissions have the highest impact on human health and the most damaging environmental impact observed was the emission of CO2.

  13. DEMONSTRATION OF PACKAGING MATERIALS ALTERNATIVES TO EXPANDED POLYSTYRENE

    Science.gov (United States)

    This report represents the second demonstration of cleaner technologies to support the goals of the 33/50 Program under the EPA Cooperative Agreement No. CR-821848. The report presents assessment results of alternative packaging materials which could potentially replace expanded...

  14. Photoconversion of gasified organic materials into biologically-degradable plastics

    Science.gov (United States)

    Weaver, Paul F.; Maness, Pin-Ching

    1993-01-01

    A process is described for converting organic materials (such as biomass wastes) into a bioplastic suitable for use as a biodegradable plastic. In a preferred embodiment the process involves thermally gasifying the organic material into primarily carbon monoxide and hydrogen, followed by photosynthetic bacterial assimilation of the gases into cell material. The process is ideally suited for waste recycling and for production of useful biodegradable plastic polymer.

  15. Photoconversion of gasified organic materials into biologically-degradable plastics

    Energy Technology Data Exchange (ETDEWEB)

    Weaver, P.F.; Pinching Maness.

    1993-10-05

    A process is described for converting organic materials (such as biomass wastes) into a bioplastic suitable for use as a biodegradable plastic. In a preferred embodiment the process involves thermally gasifying the organic material into primarily carbon monoxide and hydrogen, followed by photosynthetic bacterial assimilation of the gases into cell material. The process is ideally suited for waste recycling and for production of useful biodegradable plastic polymer. 3 figures.

  16. The radioactive materials packaging handbook: Design, operations, and maintenance

    Energy Technology Data Exchange (ETDEWEB)

    Shappert, L.B.; Bowman, S.M. [Oak Ridge National Lab., TN (United States); Arnold, E.D. [Lockheed Martin Energy Systems, Oak Ridge, TN (United States)] [and others

    1998-08-01

    As part of its required activities in 1994, the US Department of Energy (DOE) made over 500,000 shipments. Of these shipments, approximately 4% were hazardous, and of these, slightly over 1% (over 6,400 shipments) were radioactive. Because of DOE`s cleanup activities, the total quantities and percentages of radioactive material (RAM) that must be moved from one site to another is expected to increase in the coming years, and these materials are likely to be different than those shipped in the past. Irradiated fuel will certainly be part of the mix as will RAM samples and waste. However, in many cases these materials will be of different shape and size and require a transport packaging having different shielding, thermal, and criticality avoidance characteristics than are currently available. This Handbook provides guidance on the design, testing, certification, and operation of packages for these materials.

  17. Advanced materials for thermal management of electronic packaging

    CERN Document Server

    Tong, Xingcun Colin

    2011-01-01

    The need for advanced thermal management materials in electronic packaging has been widely recognized as thermal challenges become barriers to the electronic industry's ability to provide continued improvements in device and system performance. With increased performance requirements for smaller, more capable, and more efficient electronic power devices, systems ranging from active electronically scanned radar arrays to web servers all require components that can dissipate heat efficiently. This requires that the materials have high capability of dissipating heat and maintaining compatibility

  18. Development of bioactive food packaging materials using immobilised bacteriocins lacticin 3147 and nisaplin.

    Science.gov (United States)

    Scannell, A G; Hill, C; Ross, R P; Marx, S; Hartmeier, W; Elke; Arendt, K

    2000-09-25

    Immobilisation of the bacteriocins nisin and lacticin 3147 to packaging materials was investigated. Stability of both cellulose-based bioactive inserts and anti-microbial polyethylene/polyamide pouches was examined over time. Anti-microbial activity against the indicator strain Lactococcus lactis subsp. lactis HP, in addition to Listeria innocua DPC 1770 and Staphylococcus aureus MMPR3 was observed for all bacteriocin-adsorbed materials. Activity retention of the inserts showed an initial decrease in the first week of storage but remained stable for the remaining 3 months of the trial. However, adsorption of lacticin 3147 to plastic film was unsuccessful, nisin bound well and the resulting film maintained its activity for 3-month period, both at room temperature and under refrigeration. When applied to food systems, the anti-microbial packaging reduced the population of lactic acid bacteria in sliced cheese and ham stored in modified atmosphere packaging (MAP) at refrigeration temperatures, thus extending the shelf life. Nisin-adsorbed bioactive inserts reduced levels of Listeria innocua by > or = 2 log units in both products, and Staphylococcus aureus by approximately 1.5 log units in cheese, and approximately 2.8 log units in ham. Similar reductions were observed in cheese vacuum-packaged in nisin-adsorbed pouches.

  19. Associated computational plasticity schemes for nonassociated frictional materials

    DEFF Research Database (Denmark)

    Krabbenhoft, K.; Karim, M. R.; Lyamin, A. V.;

    2012-01-01

    A new methodology for computational plasticity of nonassociated frictional materials is presented. The new approach is inspired by the micromechanical origins of friction and results in a set of governing equations similar to those of standard associated plasticity. As such, procedures previously...

  20. The innovative application studty on eco-packaging design and materials

    Directory of Open Access Journals (Sweden)

    Cui Yong Min

    2016-01-01

    Full Text Available The paper solves the increasingly deteriorate environmental problems by positively exploring how to utilize and develop eco-packaging design reasonably. The paper explores an effective method that combines eco-packaging and environmental protection materials, hoping to define the sustainable development road of packaging design. The paper is centered on the design application of eco-packaging and environmental protection materials, applies and analyzes the method to obtain innovative design requirements and development tendency of eco-packaging design by analyzing status and significance of eco-packaging design, combining with the development and main types of eco-packaging packaging materials, and based on the achievements acquired by eco-packaging and environmental protection materials. Meanwhile, the paper also reveals mutual dependence and mutual promotion of eco-packaging design and eco-packaging materials.

  1. Research on application of plastic materials in cars

    Institute of Scientific and Technical Information of China (English)

    Jin Jianwei; Ma Fangwu; Liu Qiang; Wu Tiannan; Dong Ningning; Zhao Fuguan; Ma Mingtu; Guo Yihui

    2012-01-01

    This paper gives analysis of application status and prospect of plastic materials from the aspects of applied ma- terial amount comparison, development of new materials & new technologies, lightweight, design conception of new components, recyclability, simplification and diversity of materials, standardization of material specification and pres- ents corresponding conclusions and suggestions.

  2. Elasto-plastic constitutive modeling for granular materials

    Institute of Scientific and Technical Information of China (English)

    彭芳乐; 李建中

    2004-01-01

    Based on the modified plastic strain energy approach, an elasto-plastic constitutive modeling for sand was proposed. The hardening function between the modified plastic strain energy and a stress parameter was presented, which was independent of stress history and stress paths. The proposed model was related to an isotropically work-hardening and softening, non-associated and elasto-plastic material description. It is shown that the constitutive modeling, the inherent and stress system-induced cross-anisotropic elasticity is also considered. The constitutive model is capable of simulating the effects on the deformation characteristics of stress history and stress path, pressure level and anisotropic strength.

  3. Identification and quantification of oligomers as potential migrants in plastics food contact materials with a focus in polycondensates - A review

    NARCIS (Netherlands)

    Hoppe, M.; de Voogt, P.; Franz, R.

    2016-01-01

    Background: Over the last years the variety of food and beverage packaging has increased with the development of new plastic materials and (co)polymer modifications. Oligomers which are always present in polymers evoke attention as potential migrants, from a qualitatively and quantitatively viewpoin

  4. Mechanical and optical characterization of bio-nanocomposite from pineapple leaf fiber material for food packaging

    Science.gov (United States)

    Nikmatin, Siti; Rudwiyanti, Jerry R.; Prasetyo, Kurnia W.; Yedi, Dwi A.

    2015-01-01

    The utilization of Bio-nanocomposite material that was derived from pineapple leaf fiber as filler and tapioca starch with plasticizer glycerol as a matrix for food packaging can reduce the use of plastic that usually was made from petroleum materials. It is important to develop and producethis environmental friendly plastic because of limited availability of petroleum nowadays. The process of synthesize and characterization tapioca starch with the plasticizer glycerol bionanocomposites using print method had been conducted. There were 3 samples with different filler concentration variation; 3%, 4% and 5%.The results of mechanical test from each sample showed that bio-nanocomposite with 5% filler concentration was the optimum sample with 4.6320 MPa for tensile strength test and 24.87% for the elongation test. Based on the result of optical test for each sample was gained that along with the increasing of concentration filler would make the absorbance value of the sample became decreased, bio-nanocomposite with 5% filler concentration had several peaks with low absorbance values. The first peak was in 253 nm of wavelength regionwith absorbance of 0.131%, and the second peak was in 343 nmwavelength region and absorbance was 0.087%.

  5. Surveillance as an innovative tool for furthering technological development as applied to the plastic packaging sector

    Directory of Open Access Journals (Sweden)

    Freddy Abel Vargas

    2010-04-01

    Full Text Available The demand for production process efficiency and quality has made it necessary to resort to new tools for development and technological innovation. Surveillance of the enviroment has thus bee identified as beign a priority, paying special attention to technology which (by its changing nature is a key factor in competitiveness. Surveillance is a routine activity in developed countries ' organisations; however, few suitable studies have been carried out in Colombia and few instruments produced for applying it to existing sectors of the economy. The present article attempts to define a methodology for technological awareness (based on transforming the information contained in databases by means of constructing technological maps contributing useful knowledge to production processes. This methodology has been applied to the flexible plastic packaging sector. The main trends in this industry's technological development were identified allowing strategies to be proposed for incorporating these advances and tendencies in national companies and research groups involved in flexible plastic packaging technological development and innovation. Technological mappiong's possibilities as an important instrument for producing technological development in a given sector are the analysed as are their possibilities for being used in other production processes.

  6. NEW APPROACH TO ADDRESSING GAS GENERATION IN RADIOACTIVE MATERIAL PACKAGING

    Energy Technology Data Exchange (ETDEWEB)

    Watkins, R; Leduc, D; Askew, N

    2009-06-25

    Safety Analysis Reports for Packaging (SARP) document why the transportation of radioactive material is safe in Type A(F) and Type B shipping containers. The content evaluation of certain actinide materials require that the gas generation characteristics be addressed. Most packages used to transport actinides impose extremely restrictive limits on moisture content and oxide stabilization to control or prevent flammable gas generation. These requirements prevent some users from using a shipping container even though the material to be shipped is fully compliant with the remaining content envelope including isotopic distribution. To avoid these restrictions, gas generation issues have to be addressed on a case by case basis rather than a one size fits all approach. In addition, SARP applicants and review groups may not have the knowledge and experience with actinide chemistry and other factors affecting gas generation, which facility experts in actinide material processing have obtained in the last sixty years. This paper will address a proposal to create a Gas Generation Evaluation Committee to evaluate gas generation issues associated with Safety Analysis Reports for Packaging material contents. The committee charter could include reviews of both SARP approved contents and new contents not previously evaluated in a SARP.

  7. [Analysis of phthalates in plastic food-packaging bags by thin layer chromatography].

    Science.gov (United States)

    Chen, Hui; Wang, Yuan; Zhu, Ruohua

    2006-01-01

    The method for simultaneous determination of four phthalates, namely dimethyl phthalate (DMP), diethyl phthalate (DEP), di-n-butyl phthalate (DBP) and di (2-ethylhexyl) phthalate (DEHP) in plastic food-packaging bags by thin layer chromatography (TLC) was developed. The plastic food-packaging bags were extracted with ethanol by ultrasonication, then the mixture was filtrated through membrane (0.45 microm). The mixture of ethyl acetate-anhydrous ether-isooctane (1 : 4 : 15, v/v) was used as developing agent on the TLC silica gel plate for development. The filtered liquid was spotted on the TLC plate dealt by acetone, and detected with scanning wavelength of 275 nm and reference wavelength of 340 nm. The qualitative analysis of the phthalates was performed using the R(f) values of the chromatogram. The quantitative analysis was performed with external standard method. Good linearities were obtained for DMP, DEP, DBP and DEHP. The detection limits were 2.1 ng for DMP, 2.4 ng for DEP, 3.4 ng for DBP and 4.0 ng for DEHP. The relative standard deviations (RSDs) of the four phthalates were 2.8% - 3.5%. The recoveries of the four phthalate standards in real sample were 78.58% - 111.04%. The method presented has the advantages of high precision, high sensitivity, small sample size, and simple pretreatment . The method was used to detect the four phthalates in the food-packaging bags. The contents in real samples were close to the results by gas chromatography.

  8. 引线框架塑料封装集成电路分层及改善%Delamination and Its Countermeasures in IC Plastic Package

    Institute of Scientific and Technical Information of China (English)

    周朝峰; 周金成; 李习周

    2016-01-01

    Delamination is one of the common quality and reliability issues during the assembly processes and/or after reliability test in the field of IC plastic packages. How to resolve it is one of the popular researches by material suppliers, assembly process engineers and reliability engineers. The root causes of delamination and its impacts to IC plastic package are elaborated in this paper. A series of effective countermeasures against delamination are raised in this paper also, through deeply analyzing the product structure, materials and processes, which are using in IC plastic packages. One of the research results is to provide theoretical support to improve the reliability of IC plastic packages.%分层是塑料集成电路封装过程和可靠性试验后常见的问题,如何解决分层问题是封装材料供应商、封装工程师、可靠性试验工程师共同研究与改善的课题。通过对封装产品结构、材料、工艺方法等方面进行深入的解析,详细阐述了引线框架塑料封装集成电路分层产生机理,描述了分层对集成电路的危害以及如何预防分层的发生,进而提出了有效的改善措施。结果表明,这些措施的应用能够有效预防分层问题的发生,提高塑料封装集成电路的可靠性。

  9. Material efficiency improvement for European packaging in the period 2000 - 2020

    NARCIS (Netherlands)

    Hekkert, M.; Joosten, L.; Worrell, E.

    1998-01-01

    In this paper the current material consumption for packaging making in Europe is described. Per packaging type (food bottles, non-food bottles, boxes for primary packaging, flexible packaging, carrier bags, industrial boxes and pallets) options for improved material efficiency are described. The

  10. 气相色谱-质谱法检测塑料食品包装材料中的五种挥发性有机物%Determination of five kinds of volatile organic compounds in plastics food packaging materials by GC-MS

    Institute of Scientific and Technical Information of China (English)

    洪灯; 姜士磊; 许菲菲; 陈曜扬; 王旭强

    2015-01-01

    建立了使用气相色谱‐质谱仪检测塑料食品包装材料中常见的5种挥发性有机物(苯、甲苯、乙酸乙酯、乙酸丁酯、丁酮)的分析方法.实验中以欧盟标准EU 10/2011限定的4种模拟液为提取介质,二氯甲烷为有机萃取溶剂,对样品的前处理、色谱分离条件和质谱检测条件进行了优化.在最优化的实验条件下,这5种有机物能够完全分离,且在05.~200.mg/L浓度范围内线性较好,相关系数大于09.997,仪器精密度的相对标准偏差为10.8%~25.2%之间,样品在不同模拟液中的加标回收率介于81%~118%之间,最低检出限可达00.2 mg/m2.使用该方法测定了5种不同用途的塑料包装材料中的溶剂残留量,方法简便、快速、重现性好,完全能满足塑料包装材料中溶剂残留量的分析.%A procedure was developed to determinate 5 common volatile organic compounds (VOCs) (benzene ,toluene ,ethyl acetate ,butyl acetate ,butanone) in plastics food packaging materials by GC‐MS method .According to EU 10/2011 ,4 kinds of extraction media and organ‐ic solvent dichloromethane were used in the experiment ,based on which the pretreatment of the sample ,chromatograph separation condition and mass condition were optimized .Under the optimized experimental conditions ,the 5 VOCs were separated completely .In the range of 0 5.0-20 0. mg/L ,the results showed good linearity ,with a correlation coefficient better than 0 9.99 7 .The relative standard deviation of instrument were between 1 0.8% -2 5.2% ,the re‐covery of sample in different media between 81% -118% ,with the detection limit being 0 0.2 mg/m2 .5 kinds of plastics materials were analyzed .This method is simple ,rapid ,accurate and could be applied for determining the solvent residues in the plastic packing materials .

  11. Printing Technologies and Environmentally-friendly Measures of Plastic Flexible Packaging Film%塑料软包装薄膜的印刷技术及环保措施

    Institute of Scientific and Technical Information of China (English)

    庄树贵; 龚伟兵

    2011-01-01

    The printing and compounding technologies of plastic flexible packaging film were introduced.The environmentally-friendly measures in plastic flexible packaging film were expounded from the aspects of printing ink, raw material, waste material treatment, etc. The development direction of the plastic flexible packaging film was also predicted.%介绍了塑料软包装薄膜的印刷和复合工艺,从油墨、塑料原料及废弃物处理等方面阐述了塑料软包装薄膜印刷工业中采取的环保措施,并指出了塑料软包装薄质印刷工业的发展方向.

  12. RECERTIFICATION OF THE MODEL 9977 RADIOACTIVE MATERIAL PACKAGING

    Energy Technology Data Exchange (ETDEWEB)

    Abramczyk, G.; Bellamy, S.; Loftin, B.; Nathan, S.

    2013-06-05

    The Model 9977 Packaging was initially issued a Certificate of Compliance (CoC) by the Department of Energy’s Office of Environmental Management (DOE-EM) for the transportation of radioactive material (RAM) in the Fall of 2007. This first CoC was for a single radioactive material and two packing configurations. In the five years since that time, seven Addendums have been written to the Safety Analysis Report for Packaging (SARP) and five Letter Amendments have been written that have authorized either new RAM contents or packing configurations, or both. This paper will discuss the process of updating the 9977 SARP to include all the contents and configurations, including the addition of a new content, and its submittal for recertification.

  13. Potential of polymeric materials for packaging; L'impiego dei materiali polimerici nell'imballaggio

    Energy Technology Data Exchange (ETDEWEB)

    Lanchi, M. [ENEA, Divisione Nuovi Materiali, Centro Ricerche Casaccia, Rome (Italy)

    2001-07-01

    Packaging preserves different kind of materials, from raw materials, and it plays an important role in the presentation of the products to the market, too. That's why packaging should be in charge of responding to marketing requirements by means of a proper design, effective colour choice and material, etc. Nowadays packaging is becoming more and more important in different fields. In Italy, it is a rapid growth of the packaging market and the companies involved are very competitive and efficient, in particular in some market segments. Concerning the application fields it can be asserted that packaging is mostly exploited in the food market which represents the 65% of the whole packaging market. Nearly all types of packaging use plastics as a part of their construction: lightness, chemical inertness, corrosion resistance, molding attitude, the good transparency to light, sound and mechanical insulation, etc. Focusing the attention to the horticultural market, growth in South of Italy in particular, examples of promising research fields to date are: developing of good barrier performance films; developing of suitable modified atmosphere packaging; developing of active plastic films, such as antimicrobic films or antioxidant films. The large amount of plastic films used for packaging create a large waste problem. This can be reduced by: optimising packaging design, avoiding the excessive use of plastics; improvising strength, moisture and heat stability per unit weight in order to reduce plastic waste volume; developing blend of plastics and bio-based polymer in order to increase the biodegradability of packaging after use. [Italian] L'imballaggio e' un prodotto adibito a contenere e a proteggere determinate merci, dalle materie prime ai prodotti finiti, a consentire la loro manipolazione e ad assicurare la loro presentazione. E' una realta' importante del mondo della produzione, delle strutture distributive e della vita quotidiana. Nell

  14. Nuclear waste package materials testing report: basaltic and tuffaceous environments

    Energy Technology Data Exchange (ETDEWEB)

    Bradley, D.J.; Coles, D.G.; Hodges, F.N.; McVay, G.L.; Westerman, R.E.

    1983-03-01

    The disposal of high-level nuclear wastes in underground repositories in the continental United States requires the development of a waste package that will contain radionuclides for a time period commensurate with performance criteria, which may be up to 1000 years. This report addresses materials testing in support of a waste package for a basalt (Hanford, Washington) or a tuff (Nevada Test Site) repository. The materials investigated in this testing effort were: sodium and calcium bentonites and mixtures with sand or basalt as a backfill; iron and titanium-based alloys as structural barriers; and borosilicate waste glass PNL 76-68 as a waste form. The testing also incorporated site-specific rock media and ground waters: Reference Umtanum Entablature-1 basalt and reference basalt ground water, Bullfrog tuff and NTS J-13 well water. The results of the testing are discussed in four major categories: Backfill Materials: emphasizing water migration, radionuclide migration, physical property and long-term stability studies. Structural Barriers: emphasizing uniform corrosion, irradiation-corrosion, and environmental-mechanical testing. Waste Form Release Characteristics: emphasizing ground water, sample surface area/solution volume ratio, and gamma radiolysis effects. Component Compatibility: emphasizing solution/rock, glass/rock, glass/structural barrier, and glass/backfill interaction tests. This area also includes sensitivity testing to determine primary parameters to be studied, and the results of systems tests where more than two waste package components were combined during a single test.

  15. Effect of Packaging materials on Quality Parameters of Garlic

    Directory of Open Access Journals (Sweden)

    Jaspreet Singh Grewal

    2015-11-01

    Full Text Available Studies were carried out to evaluate the effect of storage period and different packaging material on the quality of garlic flakes dried by convective-cum-microwave (CCM and fluidized-cum-microwave (FCM hybrid drying. Garlic flakes were packaged and stored in high density polyethylene (HDPE, low density polyethylene (LDPE and laminated aluminium foil for 3 months under ambient conditions. Samples were investigated to observe for change in rehydration ratio, colour, physiological loss in weight % and overall acceptability. Among the hybrid drying techniques adopted, the garlic flakes developed under optimized condition of fluidized bedcum-microwave was found better in terms of shelf life and quality attributes. The aluminium packaging was adjudged to be the best in retaining the quality of dried garlic flakes up to 3 months of storage. Overall, it can be concluded that the fluidized bed cum microwave dried garlic flakes packed in Aluminium package were the best, and can be stored safely up to 3 months.

  16. The notion of a plastic material spin in atomistic simulations

    Science.gov (United States)

    Dickel, D.; Tenev, T. G.; Gullett, P.; Horstemeyer, M. F.

    2016-12-01

    A kinematic algorithm is proposed to extend existing constructions of strain tensors from atomistic data to decouple elastic and plastic contributions to the strain. Elastic and plastic deformation and ultimately the plastic spin, useful quantities in continuum mechanics and finite element simulations, are computed from the full, discrete deformation gradient and an algorithm for the local elastic deformation gradient. This elastic deformation gradient algorithm identifies a crystal type using bond angle analysis (Ackland and Jones 2006 Phys. Rev. B 73 054104) and further exploits the relationship between bond angles to determine the local deformation from an ideal crystal lattice. Full definitions of plastic deformation follow directly using a multiplicative decomposition of the deformation gradient. The results of molecular dynamics simulations of copper in simple shear and torsion are presented to demonstrate the ability of these new discrete measures to describe plastic material spin in atomistic simulation and to compare them with continuum theory.

  17. Progress of Plastic Food Packaging Safety Research%塑料食品包装材料安全性研究现状

    Institute of Scientific and Technical Information of China (English)

    秦蓓

    2011-01-01

    介绍了塑料食品包装材料中的污染物种类、污染物的分析方法以及污染物迁移到食品中的迁移模型。指出塑料包装带来的食品污染问题已经引起了世界各国的重视,各个国家纷纷制定了相应的法规以确保食品安全,最后指出了我国安全型塑料食品包装材料的研究方向。%The contaminations in plastic materials for food packaging,the analysis methods for contaminations,and the migration models of contaminations into foods were introduced.It was concluded that food pollution problems caused by plastic food packaging have already attracted attention around the world;legislations and safety regulations have been established to ensure food safety in each country.The research directions of safe plastic food packaging in our country were put forward.

  18. Materials for high-density electronic packaging and interconnection

    Science.gov (United States)

    1990-01-01

    Electronic packaging and interconnections are the elements that today limit the ultimate performance of advanced electronic systems. Materials in use today and those becoming available are critically examined to ascertain what actions are needed for U.S. industry to compete favorably in the world market for advanced electronics. Materials and processes are discussed in terms of the final properties achievable and systems design compatibility. Weak points in the domestic industrial capability, including technical, industrial philosophy, and political, are identified. Recommendations are presented for actions that could help U.S. industry regain its former leadership position in advanced semiconductor systems production.

  19. PLASTIC MATERIALS IN EUROPEAN AGRICULTURE: ACTUAL USE AND PERSPECTIVES

    Directory of Open Access Journals (Sweden)

    Giacomo Scarascia-Mugnozza

    2012-06-01

    Full Text Available The world consumption of plastics in agriculture amounts yearly to 6.5 million tons. In addition to conventional polymers used in agriculture for greenhouses and mulches such as PE, PVC, EVA, photo-selective and luminescent polymers have been used, in order to improve the quality of crops. For the same reason plastic nets are used mainly in countries with tropical and Mediterranean climates. For an environmentally friendly agricultural activity, an alternative strategy can be represented by bio-based agricultural raw materials. For low environmental impact applications, biodegradable materials for agricultural films are nowadays produced. An overview of the main methods for the disposal and recycling of plastic materials are presented with the results of mechanical and radiometric tests on recycled plastics. The strategies to reduce the burden of plastics in agriculture are: a correct procedure for the collection, disposal and recycling of post-consumption plastics; the increase of lifetime duration and performance; and the introduction and promotion of bio-based materials.

  20. Radiation degradation of plastic insulating materials

    Science.gov (United States)

    Bartoníček, B.; Hnát, V.; Janovský, I.; Pejša, R.

    1995-02-01

    Several types of polymeric compounds, used as insulating and sheathing materials of cables, were subjected to accelerated thermal and radiation ageing and to LOCA test. The stability of materials was evaluated via their mechanical properties, namely strain at break.

  1. Characterization of polymers and analysis of inorganic constituents in metallized plastic packages; Caracterizacao de polimeros e determinacao de constituintes inorganicos em embalangens plasticas metalizadas

    Energy Technology Data Exchange (ETDEWEB)

    Soares, Eufemia P.; Nunes, Edilene de Cassia D. [Escola SENAI Mario Amato, Sao Paulo, SP (Brazil)]. E-mail: eufemia_paez@hotmail.com; Saiki, Mitiko [Instituto de Pesquisas Energeticas e Nucleares (IPEN), Sao Paulo, SP (Brazil); Wiebeck, Helio [Sao Paulo Univ., SP (Brazil). Escola Politecnica

    2002-09-01

    This paper presents analytical results of metallized plastic materials obtained by neutron activation analysis (NAA) and the results of identification of polymers by infrared spectroscopy (IR) and differential scanning calorimetry (DSC). Metallized plastic samples were collected from packages of foodstuffs and cosmetics. Results of IR and DSC tests indicated that polyethylene, polypropylene, poly(ethylene terephthalate) and polystyrene are polymers used in metallized plastics. The NAA consisted of irradiating samples and standards with thermal neutron flux of the IEA-R1 nuclear reactor, followed by induced gamma ray activities measurements using a hyper pure germanium detector coupled to a gamma ray spectrometer. Toxic elements such as arsenic, cadmium, chromium, nickel and antimony as well as non-toxic elements as barium, calcium, cobalt,iron, scandium,, selenium and zinc were determined and their concentrations presented a large variability between the samples. The analyses of polymer and toxic elements are of great interest to develop adequate and safe processes for recycling or incineration of metallized plastic packages without causing damage to the environment. (author)

  2. 41 CFR 50-204.26 - Exemptions for radioactive materials packaged for shipment.

    Science.gov (United States)

    2010-07-01

    ... radioactive materials packaged for shipment. 50-204.26 Section 50-204.26 Public Contracts and Property... HEALTH STANDARDS FOR FEDERAL SUPPLY CONTRACTS Radiation Standards § 50-204.26 Exemptions for radioactive materials packaged for shipment. Radioactive materials packaged and labeled in accordance with...

  3. 10 CFR 835.405 - Receipt of packages containing radioactive material.

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 4 2010-01-01 2010-01-01 false Receipt of packages containing radioactive material. 835... Individuals and Areas § 835.405 Receipt of packages containing radioactive material. (a) If packages containing quantities of radioactive material in excess of a Type A quantity (as defined at 10 CFR 71.4)...

  4. Spallation products induced by energetic neutrons in plastic detector material

    CERN Document Server

    Grabisch, K; Enge, W; Scherzer, R

    1977-01-01

    Cellulose nitrate plastic detector sheets were irradiated with secondary neutrons of the 22 GeV/c proton beam at the CERN accelerator. He, Li and Be particles which are produced in nuclear interactions of the neutrons with the target elements C, N and O of the plastic detector material are measured. Preliminary angle and range distributions and isotropic abundances of the secondary particles are discussed. (6 refs).

  5. [Carbon fiber-reinforced plastics as implant materials].

    Science.gov (United States)

    Bader, R; Steinhauser, E; Rechl, H; Siebels, W; Mittelmeier, W; Gradinger, R

    2003-01-01

    Carbon fiber-reinforced plastics have been used clinically as an implant material for different applications for over 20 years.A review of technical basics of the composite materials (carbon fibers and matrix systems), fields of application,advantages (e.g., postoperative visualization without distortion in computed and magnetic resonance tomography), and disadvantages with use as an implant material is given. The question of the biocompatibility of carbon fiber-reinforced plastics is discussed on the basis of experimental and clinical studies. Selected implant systems made of carbon composite materials for treatments in orthopedic surgery such as joint replacement, tumor surgery, and spinal operations are presented and assessed. Present applications for carbon fiber reinforced plastics are seen in the field of spinal surgery, both as cages for interbody fusion and vertebral body replacement.

  6. Particulate Filled Composite Plastic Materials from Recycled Glass Fibre Reinforced Plastics

    Directory of Open Access Journals (Sweden)

    Aare ARUNIIT

    2011-09-01

    Full Text Available Glass fibre reinforced plastic (GFRP scrap consisted of acrylic plastic with glass fibre reinforcement in polyester resin matrix was used in our experiments. The multi-functional DS-series disintegrator mills were used for mechanical processing of GFRP scrap. Preceding from the results characterization of the milled powder particles size, shape and other properties the numerical algorithm for modelling of the density of the new filler material was developed. The main goal of the current study is to develop new particulate filled composite plastic material from recycled GFRP scrap. With recovered plastic powder material the higher filler content in polyester resin matrix can be achieved. The new composite is modelled on basis of the properties of new material. Such an approach requires tests of the new material. The considered target characteristics of the new material are the tensile strength, elongation at break and the cost. The multicriteria optimization problem has been formulated and solved by use of physical programming techniques and Pareto optimality concept. The designed new composites were manufactured in different mixing ratios of powder and binder agent. The strength and stiffness properties of new composite material were tested. http://dx.doi.org/10.5755/j01.ms.17.3.593

  7. Elastic stresses and plastic deformations in 'Santa Clara' tomato fruits caused by package dependent compression

    Directory of Open Access Journals (Sweden)

    PEREIRA ADRIANA VARGAS

    2000-01-01

    Full Text Available The objective of this work was to study the fruit compression behavior aiming to develop new tomato packages. Deformations caused by compression forces were observed inside packages and in individual 'Santa Clara' tomato fruit. The forces applied by a transparent acrylic lever to the fruit surface caused pericarp deformation and the flattened area was proportional to the force magnitude. The deformation was associated to the reduction in the gas volume (Vg, caused by expulsion of the air from the loculus cavity and reduction in the intercellular air volume of the pericarp. As ripening advanced, smaller fractions of the Vg reduced by the compressive force were restored after the stress was relieved. The lack of complete Vg restoration was an indication of permanent plastic deformations of the stressed cells. Vg regeneration (elastic recovery was larger in green fruits than in the red ones. The ratio between the applied force and the flattened area (flattening pressure, which depends on cell turgidity, decreased during ripening. Fruit movements associated with its depth in the container were observed during storage in a transparent glass container (495 x 355 x 220 mm. The downward movement of the fruits was larger in the top layers because these movements seem to be driven by a summation of the deformation of many fruits in all layers.

  8. A plastic micropump constructed with conventional techniques and materials

    NARCIS (Netherlands)

    Bohm, Sebastian; Olthuis, Wouter; Bergveld, P.

    1999-01-01

    A plastic micropump which can be produced using conventional production techniques and materials is presented. By applying well-known techniques and materials, economic fabrication of micropumps for various applications is feasible even at low production volumes. The micropump is capable of pumping

  9. Energetic materials: crystallization, characterization and insensitive plastic bonded explosives

    NARCIS (Netherlands)

    Heijden, A.E.D.M. van der; Creyghton, Y.L.M.; Marino, E.; Bouma, R.H.B.; Scholtes, G.J.H.G.; Duvalois, W.; Roelands, C.P.M.

    2008-01-01

    The product quality of energetic materials is predominantly determined by the crystallization process applied to produce these materials. It has been demonstrated in the past that the higher the product quality of the solid energetic ingredients, the less sensitive a plastic bonded explosive contain

  10. Energetic materials: crystallization, characterization and insensitive plastic bonded explosives

    NARCIS (Netherlands)

    Heijden, A.E.D.M. van der; Creyghton, Y.L.M.; Marino, E.; Bouma, R.H.B.; Scholtes, G.J.H.G.; Duvalois, W.; Roelands, C.P.M.

    2008-01-01

    The product quality of energetic materials is predominantly determined by the crystallization process applied to produce these materials. It has been demonstrated in the past that the higher the product quality of the solid energetic ingredients, the less sensitive a plastic bonded explosive

  11. Estrogenic potency of food-packaging-associated plasticizers and antioxidants as detected in ERa and ERb reporter gene cell lines

    NARCIS (Netherlands)

    Veld, ter M.G.R.; Schouten, B.; Louisse, J.; Es, van D.S.; Saag, van der P.T.; Rietjens, I.M.C.M.; Murk, A.J.

    2006-01-01

    This study presents the estrogenic potency of 21 food-packaging-associated compounds determined for the first time, using two transfected U2-OS (human osteoblasts devoid of endogenous estrogen receptors) estrogen receptor (ER) alpha and beta cell lines. Six plasticizers and three antioxidants were s

  12. Predictive modeling of migration from packaging materials into food products for regulatory purposes

    NARCIS (Netherlands)

    Helmroth, I.E.; Rijk, R.; Dekker, M.; Jongen, W.M.F.

    2002-01-01

    Migration of low-molecular weight compounds is one of the most important problems of packaging plastics and other plastics intended to come into contact with food products. Since migration experiments are time consuming and expensive, predictive modelling has been introduced as a promising alternati

  13. Properties of Whey-Protein-Coated Films and Laminates as Novel Recyclable Food Packaging Materials with Excellent Barrier Properties

    Directory of Open Access Journals (Sweden)

    Markus Schmid

    2012-01-01

    Full Text Available In case of food packaging applications, high oxygen and water vapour barriers are the prerequisite conditions for preserving the quality of the products throughout their whole lifecycle. Currently available polymers and/or biopolymer films are mostly used in combination with barrier materials derived from oil based plastics or aluminium to enhance their low barrier properties. In order to replace these non-renewable materials, current research efforts are focused on the development of sustainable coatings, while maintaining the functional properties of the resulting packaging materials. This article provides an introduction to food packaging requirements, highlights prior art on the use of whey-based coatings for their barriers properties, and describes the key properties of an innovative packaging multilayer material that includes a whey-based layer. The developed whey protein formulations had excellent barrier properties almost comparable to the ethylene vinyl alcohol copolymers (EVOH barrier layer conventionally used in food packaging composites, with an oxygen barrier (OTR of <2 [cm³(STP/(m²d bar] when normalized to a thickness of 100 μm. Further requirements of the barrier layer are good adhesion to the substrate and sufficient flexibility to withstand mechanical load while preventing delamination and/or brittle fracture. Whey-protein-based coatings have successfully met these functional and mechanical requirements.

  14. Mesoporous silica as carrier of antioxidant for food packaging materials

    Science.gov (United States)

    Buonocore, Giovanna Giuliana; Gargiulo, Nicola; Verdolotti, Letizia; Liguori, Barbara; Lavorgna, Marino; Caputo, Domenico

    2014-05-01

    Mesoporous silicas have been long recognized as very promising materials for the preparation of drug delivery systems. In this work SBA-15 mesoporous silica has been functionalized with amino-silane to be used as carrier of antioxidant compound in the preparation of active food packaging materials exhibiting tailored release properties. Active films have been prepared by loading the antioxidant tocopherol, the purely siliceous SBA-15 and the aminofunctionalized SBA-15 loaded with tocopherol into LDPE matrix trough a two-step process (mixing+extrusion). The aim of the present work is the study of the effect of the pore size and of the chemical functionality of the internal walls of the mesophase on the migration of tocopherol from active LDPE polymer films. Moreover, it has been proved that the addition of the active compound do not worsen the properties of the film such as optical characteristic and water vapor permeability, thus leading to the development of a material which could be favorably used mainly, but not exclusively, in the sector of food packaging.

  15. Fracture of anisotropic materials with plastic strain-gradient effects

    DEFF Research Database (Denmark)

    Legarth, Brian Nyvang

    2013-01-01

    parameter is adopted. The fracture process along the fiber-matrix interface is modeled using a recently proposed cohesive law extension having an additional material length parameter. Due to the fiber-matrix fracture a sudden stress-drop is seen in the macroscopic stress-strain response which defines......A unit cell is adopted to numerically analyze the effect of plastic anisotropy on frac-ture evolution in a micro-reinforced fiber-composite. The matrix material exhibit size-effects and an anisotropic strain-gradient plasticity model accounting for such size-effects through a mate-rial length scale...... the failure strain of the composite. The effect of the two material length parameters on the failure strain of the composite is studied. For small values of the material length scale parameter conventional predictions are obtained. Larger values of the material length scale parameter result in corresponding...

  16. Plastic raw materials in Neolithic pottery production

    Directory of Open Access Journals (Sweden)

    Alexander A. Bobrinsky

    2012-12-01

    Full Text Available The paper is dedicated to the investigation of various natural silts as the most ancient type of raw material used in pottery production. The authors describe the specific features of the composition of plain and mountain silts, and discover the same features in ancient ceramics from different regions in Russia. It can be concluded that silts were the earliest raw material used, a tradition that faded away during the evolution of pottery production.

  17. Effects of packaging materials on some ripening characteristics of Tulum cheese

    Directory of Open Access Journals (Sweden)

    Zekai Tarakçı

    2016-11-01

    Full Text Available In this study the effects of different packaging materials on Tulum cheese made with cloth, stomach, animal skin, pot and plastic materials were investigated. Dry matter, ash, titratable acidity, salt, salt in dry matter, fat, total protein, water soluble nitrogen (WSN, trichloroacetic acid soluble nitrogen (TCA-SN, phosphotungstic acid soluble nitrogen (PTA-SN, electrophoretic casein fraction analyses, L*, a* and b* values in colour analyses and sensory characteristics were analysed. Dry matter 54.74-66.37 %, ash 3.93-4.79 %, titratable acidity 1.22-1.80 % as lactic acid, salt 2.48-3.93 %, salt in the dry matter 3.78-6.20 %, fat 21-43 %, total protein 17.20-23.16 %, WSN ratio 5.58-16.81 %, TCA-SN ratio 4.33-13.59 %, PTA-SN ratio 2.06-5.12 %, β-CN ratio 31.01-52.16 %, αs1-CN ratio 33.52-47.84 %, and in colour measurements L*, a* and b* values ranged from 82.18-84.39, 0.93-1.72 and 8.41-16.51, respectively. Accordingly it was clarified that the use of different packaging materials affected the composition of Tulum cheese and was related to from the cheese origin as well.

  18. 基体匹配校正-顶空-气相色谱法测定食品塑料包装材料中挥发性有机物%Head-Space-GC Determination of Volatile Organic Compounds in Plastic Packaging Materials for Foodstuffs with Matrix Matching Calibration

    Institute of Scientific and Technical Information of China (English)

    程欲晓; 周宇艳; 马明

    2012-01-01

    Ten volatile organic compounds(VOC′s),i.e.,toluene,ethyl acetate,2,4-pentanedione,2-ethyl-1-hexanol,1-nanaldehyde,decanecarbaldehyde,dodecanacarbaldehyde,decane,octane and dodecane in soft plastic packaging materials were determined by head-space gas chromatography using matrix matching calibration to compensate the matrix interference.A representative portion of the sample(packaging film,ca.100 cm2) was taken and stoved in a vacuum oven at 90 ℃ for 24 h.This portion of the sample was cut and used as blank matrix for preparation of calibration curve and definita amounts of standard solutions of the 10 VOC′s wer added to it and treated in the same way as the sample.A similar portion of the sample was cut and transferred into the headspace bottle,closed the bottle immediately and equilibrized at 100 ℃ for 30 min.HP-INNOWAX chromatographic column was used for separation at programed temperature elevation from 20 ℃ to 220 ℃.FID was adopted for determination.Detection limits(3S/N) found for the 10 VOC′s were ranged from 0.2 to 2.0 μg·dm-2.Values of recovery and RSD′s(n=6) were in the ranges of 82.5%-97.6% and 1.0%-14.0% respectively.%采用顶空-气相色谱法测定了食品用软质塑料包装材料中具有代表的10种挥发性有机物(VOC′s),包括甲苯、乙酸乙酯、2,4-戊二酮、2-乙基-1-己醇、1-壬醛、癸烷醛、十二烷醛、癸烷、正辛烷及十二烷,并用基体匹配法抵消了样品本身的基体干扰。从待分析样品(包装膜)裁取约100cm2大小片样置于真空烘箱中,于90℃烘24h,此片试样即可作为空白基质,再加入一定量的上述VOC标准溶液制备校准曲线。另取同一样品一片,剪碎后移入顶空瓶中,立即盖紧,在100℃平衡30min。方法中用HP-INNOWAX色谱柱在20℃~220℃温度区间程序升温,对各VOC进行分离,采用火焰离子化检测器检测。测得10种VOC′s的检出限(3S/N)在0.2~2.0μg.dm-2之间。另测

  19. Mechanical behavior of plastic materials for automobile cockpit module

    Science.gov (United States)

    Woo, Changsu.; Park, Hyunsung.; Jo, Jinho.

    2013-12-01

    Engineering plastics are used in instrument panels, interior trims, and other vehicle applications, and the thermo-mechanical behaviors of plastic materials are strongly influenced by many environmental factors such as temperature, sunlight, and rain. As the material properties change, the mechanical parts create unexpected noise. In this study, the dynamic mechanical property changes of plastics used in automobiles are measured to investigate the effect of temperature. Visco-elastic properties such as the glass transition temperature and storage modulus and loss factors under temperature and frequency sweeps were measured. The data results were compared with the original ones before aging to analyze the behavioral changes. It was found that as the temperature increased, the storage modulus decreased and the loss factor increased slightly.

  20. 一次性纸塑包装在精神科临床的应用%Application of Disposable Plastic Packaging in Psychiatric Department

    Institute of Scientific and Technical Information of China (English)

    万雪梅

    2015-01-01

    目的探讨一次性纸塑包装经高压蒸汽灭菌后的临床应用。方法将临床常用的医疗器械采用一次性纸塑包装材料包装成30个试验包分别与灭菌后30~180d进行无菌试验。结果无菌试验结果无菌生长。结论通过将使用棉布包装的各类静切,缝合、胸穿包等改为纸塑包装,使临床利用率比较低的器械包经灭菌后保存相对长时间,便于日常使用,一方面节省人力和物力资源,将更多的时间还给了护士,另一方面大大减少灭菌工作量,有效保存无菌物品,节<了成本,增加了经济效益,确保医疗和护理安全,有效地防止医院感染的发生。%Objective To investigate the disposable the clinical application of paper-plastic packaging after high pressure steam sterilization.Methods Clinical commonly used medical devices using disposable paper-plastic packaging materials packaging into 30 test package respectively with 30~180 days after sterilization sterile test. Results The sterile sterile growth test results.Conclusion By using cot on packaging of al kinds of static cut ing, sewing,chest wear bag instead of paper-plastic packaging, such as the clinical utilization low instrument set relatively long time after sterilization, convenient for daily use,save manpower and material resources on the one hand, wil be more time returned to the nurse,on the other hand,greatly reduce the workload of sterilization,ef ectively keep sterile items,saving the cost and increase the economic ef iciency,to ensure that medical and nursing safety,ef ectively prevent hospital infection.

  1. The innovative application studty on eco-packaging design and materials

    OpenAIRE

    Cui Yong Min; Ren Xin Guang

    2016-01-01

    The paper solves the increasingly deteriorate environmental problems by positively exploring how to utilize and develop eco-packaging design reasonably. The paper explores an effective method that combines eco-packaging and environmental protection materials, hoping to define the sustainable development road of packaging design. The paper is centered on the design application of eco-packaging and environmental protection materials, applies and analyzes the method to obtain innovative design r...

  2. The innovative application studty on eco-packaging design and materials

    OpenAIRE

    Cui Yong Min; Ren Xin Guang

    2016-01-01

    The paper solves the increasingly deteriorate environmental problems by positively exploring how to utilize and develop eco-packaging design reasonably. The paper explores an effective method that combines eco-packaging and environmental protection materials, hoping to define the sustainable development road of packaging design. The paper is centered on the design application of eco-packaging and environmental protection materials, applies and analyzes the method to obtain innovative design r...

  3. Plastic plus stainless-steel fibers make resilient, impermeable material

    Science.gov (United States)

    Smirra, J. R.

    1965-01-01

    Plastic material combined with stainless-steel fibers and molded under heat and pressure into a desired configuration is both soft enough to deform under a load and resilient enough to return to its original shape when the load is removed.

  4. Extraction of stearate salts from plastic materials used in pharmaceutical applications.

    Science.gov (United States)

    Jenke, Dennis

    2010-01-01

    Plastic materials are widely used in medical items such as solution containers, infusion sets, transfer tubing, devices, processing equipment and systems, filters, and the like. Components in medical items can leach out of such items when they are contacted by a therapeutic product or product-related solution. Stearic acid and stearate salts are commonly present in medical and food packaging, either as plastic additives, processing aids, or contaminants, and their leaching from plastics is well documented. With a pK(a) in the range of 5.1 to 5.6 and limited aqueous solubility (log P(o/w) greater than 8), the leaching of stearic acid (and its related metal salts) into pharmaceutical products is expected to be strongly dependent on the product's pH and polarity. In order to establish and understand the leaching behavior of stearate-containing materials, three compounds (stearic acid, calcium stearate, and zinc stearate) and four polymeric materials containing these compounds were contacted with aqueous buffers in the pH range of 2.5 to 11. The leached levels of calcium, zinc, stearate, palmitate, and total organic carbon (TOC) were measured in the resulting solutions and are reported. For materials containing only stearic acid or salts themselves, the extraction of these entities is pH-dependent. At low pH, the cation counter-ions of the stearate salts are extracted from the plastic materials by a process that can loosely be termed ion exchange. At intermediate pH, little or no extraction of the stearates occurs. At high pH, the stearates are extracted from the materials to a very limited extent due to the solubility of the acid and/or salts in the extraction medium.

  5. ANALYTICAL SOLUTIONS OF THERMAL STRESS DISTRIBUTION IN PLASTIC ENCAPSULATED INTEGRATED CIRCUIT PACKAGES

    Institute of Scientific and Technical Information of China (English)

    刘玉岚; 王彪; 王殿富

    2003-01-01

    Due to the mismatch in the coefficients of thermal expansion of slicon chip and the surrounding plastic encapsulation materials, the induced thermal stress is the main cause for die and encapsulant rupture. The corner geometry is simplified as the semi-infinite wedge. Then the two-dimensional thermal stress distribution around the corner was obtained explicitly. Based on the stress calculation, the strain energy density factor criterion is used to evaluate the strength of the structure, which can not only give the critical condition for the stresses, but also determine the direction of fracture initiation around the corner.

  6. ANALYTICAL SOLUTIONS OF THERMAL STRESS DISTRIBUTION IN PLASTIC ENCAPSULATED INTEGRATED CIRCUIT PACKAGES

    Institute of Scientific and Technical Information of China (English)

    LIUYu-lan; WANGBiao; WANGDian-fu

    2003-01-01

    Due to the mismatch in the coefficients of thermal epansion of slicon chip and the surrounding plastic encapsulation materials,the induced thermal stress is the main cause for die and encapsulant rupture.The corner geometry is simplified as the semi-infinite wedge.The the two-dimensional thermal stress distribution around the coner was obtained explicitly.Based on the stress calculation,the strain energy density factor criterion is used to evaluate the strength of the structure,which can not only give the critical condition for the stresses,but also determine the direction of fracture iuntiation around the corner.

  7. Advances of bio-plastics in food packaging application%食品包装用生物塑料研究进展

    Institute of Scientific and Technical Information of China (English)

    何江川; 张睿; 王颖

    2011-01-01

    在白色污染和石油危机日趋严重的今天,具有生态友好特征和可持续性的生物基质-生物分解塑料有望替代 部分石油基塑料成为一种新型基础原材料,在农业、包装、生物医用等领域已开始显示出巨大的市场潜力.本文介绍 了聚乳酸、淀粉基塑料、聚羟基烷酸酯等几类最有可能率先实现产业化并用于食品包装材料的生物基质-生物分解塑 料,对其在食品包装材料应用方面所具有的优势和存在的问题进行了评价,并对目前国内外在这几类材料的生产和应 用技术及产业化等方面的最新进展进行了归纳.%Biomass- based biodegradable plastics characteristic of ecological concern and sustainability are expected to become a novel category of basic raw materials in a wide range of potential applications such as agriculture, packaging and biomedical ,when white pollution and oil crisis are increasingly serious today. The main categories of biomass- based biodegradable plastics, including poly( lactic acid), starch-based plastics and poly hydroxylalkanoates were introduced,which may most probably take the lead to be commercialized and used for food packaging. Their advantage and shortage in the application of food packaging were commented. The latest development of the manufacturing and applying techniques of these materials together with their industrialization status throughout the world was overviewed.

  8. Theory of Lattice Strain for Materials Undergoing Plastic Deformation

    Science.gov (United States)

    Karato, S.

    2008-12-01

    Radial x-ray diffraction is used to probe physical properties of materials including elastic and plastic properties. The theory used behind such an practice is the one developed by Singh (1993) in which the relation between lattice strain and elastic constants and macroscopic stress is derived. In this theory, the variation of inferred stress with the crystallographic planes, (hkl), is due to the elastic anisotropy. However, recent experimental studies showed that in many cases, the variation of stress with (hkl) far exceeds the value expected from this theory. I have developed a modified theory to rectify this problem with Singh's theory. In Singh's theory, the stress distribution in a polycrystalline material is treated only either unrelaxed or relaxed state. The role of plastic deformation is included only to the extent that plastic flow influences this stress state. Such an assumption corresponds to a Voigt model behavior, which is not an appropriate model at high temperatures where continuing plastic flow occurs with concurrent microscopic equilibrium, elastic deformation. This is a Maxwell model type behavior, and my model provides a stress analysis in a Maxwell material with anisotropic and non-linear power-law rheology. In this theory, the lattice strain corresponding to an imposed macroscopic strain-rate is calculated by three steps: (i) conversion of macroscopic strain-rate to macroscopic stress, (ii) conversion of macroscopic stress to microscopic stress at individual grains, and (iii) calculation of microscopic strain due to microscopic stress. The first step involves anisotropy in macroscopic viscosity that depends on anisotropy in crystal plasticity and lattice-preferred orientation. The second step involves anisotropic crystal plasticity and finally the third step involves elastic crystal anisotropy. In most cases, the influence of LPO is weak and in such a case, the lattice strain depends on (hkl) due to the anisotropy in both elastic and plastic

  9. Strategies to improve the mechanical properties of starch-based materials: plasticization and natural fibers reinforcement

    Directory of Open Access Journals (Sweden)

    A. Lopez-Gil

    2014-01-01

    Full Text Available Biodegradable polymers are starting to be introduced as raw materials in the food-packaging market. Nevertheless, their price is very high. Starch, a fully biodegradable and bioderived polymer is a very interesting alternative due to its very low price. However, the use of starch as the polymer matrix for the production of rigid food packaging, such as trays, is limited due to its poor mechanical properties, high hidrophilicity and high density. This work presents two strategies to overcome the poor mechanical properties of starch. First, the plasticization of starch with several amounts of glycerol to produce thermoplastic starch (TPS and second, the production of biocomposites by reinforcing TPS with promising fibers, such as barley straw and grape waste. The mechanical properties obtained are compared with the values predicted by models used in the field of composites; law of mixtures, Kerner-Nielsen and Halpin-Tsai. To evaluate if the materials developed are suitable for the production of food-packaging trays, the TPS-based materials with better mechanical properties were compared with commercial grades of oil-based polymers, polypropylene (PP and polyethylene-terphthalate (PET, and a biodegradable polymer, polylactic acid (PLA.

  10. 49 CFR 173.422 - Additional requirements for excepted packages containing Class 7 (radioactive) materials.

    Science.gov (United States)

    2010-10-01

    ... containing Class 7 (radioactive) materials. 173.422 Section 173.422 Transportation Other Regulations Relating... (Radioactive) Materials § 173.422 Additional requirements for excepted packages containing Class 7 (radioactive) materials. An excepted package of Class 7 (radioactive) material that is prepared for shipment under...

  11. [Mutual relations between plastic materials and bacteria (author's transl)].

    Science.gov (United States)

    Toepfer, C T; Kanz, E

    1976-12-01

    The complex problems of microbiological degradation of synthetic plastics and a fairly wide variety of 62 testing materials, belonging to 14 major groups of plastics, are described. Adaequate and reliable testing techniques had to be devised. Drawing on the experiences of H. Braun, 1930, and of Bushnell and Haas, 1941, as to the metabolism of bacteria and the utilization of certain hydrocarbons by microorganisms, and previous research work by A. Schwartz in Berlin, 1959-60, on microbial corrosion of plastics, methods of laboratory testing were developed. The bacteriological technique was based on selection of aerobic microorganisms, which were, by starvation, adapted to use the plastic materials as their only carbon source; foreign carbon sources had to be strictly eliminated; emphasis was laid on proper, double control cultures. The test organisms involved included P. aeruginosa and fluorescens strains, also a certain species of Candida, and mixtures of soil, sewage and garbage organisms grown on exposed plastic surfaces. By means of series of passages the selective adaptation and conservation of these organisms was continued up to 4 1/2 years. An anaerobic adaptation method for Desulfovibrio desulfuricans was developed and used successfully. After preliminary experimentation (Soil burial, sewage and garbage exposure tests) in the laboratory as well as in the open, a large scale Field testing programme under realistic and to some extent extreme conditions was implemented: Nine different plastic materials comprising eight plain high polymer plastics and for comparison one synthetic Cellulose derivate, together with glass control samples, were exposed in twelve different sewage, garbage, and soil media over a period of 3 months to 2 years, and subsequently examined. On the basis of the bacteriological results obtained from the adaptation series the test materials were classified into three categories, corresponding to the stimulation of bacterial growth: Group one

  12. Electrically conductive and thermally conductive materials for electronic packaging

    Science.gov (United States)

    Liu, Zongrong

    The aim of this dissertation is to develop electrically or thermally conductive materials that are needed for electronic packaging and microelectronic cooling. These materials are in the form of coatings and are made from pastes. The research work encompasses paste formulation, studying the process of converting a paste to a conductive material, relating the processing conditions to the structure and performance, and evaluating performance attributes that are relevant to the application of these conductive materials. The research has resulted in new information that is valuable to the microelectronic industry. Work on electrically conductive materials emphasizes the development of electrical interconnection materials in the form of air-firable glass-free silver-based electrically conductive thick films, which use the Ti-Al alloy as the binder and are in contrast to conventional films that use glass as the binder. The air-firability, as enabled by minor additions of tin and zinc to the paste, is in contrast to previous glass-free films that are not firable. The recommended firing condition is 930°C in air. The organic vehicle in the paste comprises ethyl cellulose, which undergoes thermal decomposition during burnout of the paste. The ethyl cellulose is dissolved in ether, which facilitates the burnout. Excessive ethyl cellulose hinders the burnout. A higher heating rate results in more residue after burnout. The presence of silver particles facilitates drying and burnout. Firing in air gives lower resistivity than firing in oxygen. Firing in argon gives poor films. Compared to conventional films that use glass as the binder, these films, when appropriately fired, exhibit lower electrical resistivity (2.5 x 10-6 O.cm) and higher scratch resistance. Work on thermally conductive materials addresses thermal interface materials, which are materials placed at the interface between a heat sink and a heat source for the purpose of improving the thermal contact. Heat

  13. Materials selection for a transport packaging of Mo-99

    Energy Technology Data Exchange (ETDEWEB)

    Hara, Debora H.S.; Lucchesi, Raquel F.; Mancini, Victor A.; Rossi, Jesualdo L., E-mail: debora_hara@yahoo.com.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil); Fiore, Marina [Universidade de Sao Paulo (USP), SP (Brazil). Departamento de Engenharia Metalurgica e de Materiais. Escola Politecnica

    2015-07-01

    The radiopharmaceuticals are radioactive isotopes used in nuclear medicine for more accurate diagnosis and treatment of diseases or dysfunctions. Currently, the most important radionuclide for the preparation of radiopharmaceuticals for diagnostic purposes is technetium-99m ({sup 99m}Tc), a product of the radioactive decay of molybdenum-99 (Mo-99). The aim of this work was the materials selection that can enable the manufacture of a package for Mo-99 transport with the aid of CES EduPack program and the methodology developed by Ashby. The ESTAR program was used to check the occurrence of Bremsstrahlung and the XCOM program was used to calculate the attenuation coefficient of gamma radiation from some of the selected materials for the shield; after, the thickness required for radiation shielding was calculated. From the results, the materials selected as potential candidates for the manufacture of the shielding were the tungsten alloys. Related to the thermal insulation and the impact protection, woods, plywoods and particle boards stand out. With regard to internal and external coatings, the selected materials focus on groups of steels and nickel alloys. (author)

  14. Biodegradable Long Shelf Life Food Packaging Material Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Long shelf life food packaging is a critical to maintaining the crew's well being in NASA's manned missions to the mars. Not only does the packaging have to offer an...

  15. Standard Guide for Testing Materials for Aerospace Plastic Transparent Enclosures

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2008-01-01

    1.1 This guide is intended to summarize the standard test methods available on individual and composite materials utilized in fabrication of aerospace plastic transparent enclosures. As such, it is intended to specifically include transparent thermoplastics, transparent elastomers, and reinforced plastics, whether thermoplastic or thermosetting. 1.2 This guide is intended as an aid in the search for test methods pertinent to Aerospace Plastic Transparent Enclosures. It should be understood that all methods listed may not apply to all enclosures. 1.3 The standards included refer to the properties or aspects listed in Table 1. The properties or aspects are listed in alphabetical order and the descriptions used are intended to facilitate the search. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limi...

  16. Polymers and paper as packaging materials of irradiated food

    Science.gov (United States)

    Pentimalli, M.; Ragni, P.; Righini, G.; Capitani, D.

    2000-03-01

    Effects of γ-irradiation on synthetic polymers and paper used as packaging materials for irradiated food have been studied by NMR. Polystyrene, polybutadiene and some copolymers were studied before and after the γ-irradiation treatment and in the presence or absence of antioxidants and stabilisers. In the absence of additives, the effect of γ-irradiation on polystyrene is negligible even irradiating at high doses. In turn, the role of antioxidants and stabilisers is crucial in polybutadiene and butadiene-containing copolymers. Wood pulp paper was also studied by NMR. Preliminary measurements on γ-irradiated wood pulp sheets show a shortening in the T2 relaxation time component due to the bound water, i.e. some of the bound water is lost.

  17. Life cycle Analysis of Aluminum Foil Packaging Material.

    Science.gov (United States)

    El Sebaie, Olfat; Ahmed, Manal; Hussein, Ahmed; El Sharkawy, Fahmay; Samy, Manal

    2006-01-01

    A fundamental tent of life cycle analysis (LCA) is that every material product must become a waste. To choose the greener products, it is necessary to take into account their environmental impacts from cradle to grave. LCA is the tool used to measure environmental improvements. Aluminum (Al) is the third most common element found in the earth's crust, after oxygen and silicon. Al packaging foil was chosen as the material for the study with its life cycle perspective at Alexandria. The Al packaging produced from virgin and recycled Al was investigated through life cycle stages in these two production processes; primary and secondary. The aim of this study is to evaluate the environmental impact of aluminum packaging process by using life cycle analysis of its product from two different starting raw materials (virgin and recycled aluminum). The input and output materials, energy, water, natural gas consumptions, and solid waste uses in the foil industry had been analyzed in order to identify those with significant contribution to the total environmental impacts. From the survey done on the two life cycles, it was found that in environmental terms, the most important emissions from the primary process are the emission of CO(2) and perfluorocarbon (PFC) gases, which produce the greenhouse effect, and SO(2) as well as the emission of fluorides and polyaromatic hydrocarbons (PAH compounds), which are toxic to humans and the environment. On over all material balance, it was found that the ingot shares by 45% of the feed to the casthouse furnaces at Egyptian Copper Work (ECW), net production of the casthouse is 43.76% and the yield of rotary dross furnace (RDF) is 28.8%. The net production of the foil unit represents 35% of the total input to the unit. By comparing the two life cycles, it is obvious that, for water consumption, 93.5% is used in the primary cycle, while 6.5% is used in the secondary cycle. For electricity consumption, 99.3% is used in the primary cycle

  18. Effect of plasticizer type and concentration on physical properties of biodegradable films based on sugar palm (arenga pinnata) starch for food packaging.

    Science.gov (United States)

    Sanyang, M L; Sapuan, S M; Jawaid, M; Ishak, M R; Sahari, J

    2016-01-01

    In this study, sugar palm starch (SPS) films were developed using glycerol (G), sorbitol (S) or their combination (GS) as plasticizers at the ratio of 15, 30 and 45 (wt)% using casting technique. The addition of plasticizers to SPS film-forming solutions helped to overcome the brittle and fragile nature of unplasticized SPS films. Increased plasticizer concentration resulted to an increase in film thickness, moisture content and solubility. On the contrary, density and water absorption of plasticized films decreased with increasing plasticizer concentration. Raising the plasticizer content from 15 to 45 % showed less effect on the moisture content and water absorption of S-plasticized films. Films containing glycerol and glycerol-sorbitol plasticizer (G, and GS) demonstrated higher moisture content, solubility and water absorption capacity compared to S-plasticized films. The results obtained in this study showed that plasticizer type and concentration significantly improves film properties and enhances their suitability for food packaging applications.

  19. Nuclear materials stabilization and packaging. Quarterly status report, January 1--March 31, 1996

    Energy Technology Data Exchange (ETDEWEB)

    Haschke, J.M.; Horrell, D.R.; Hoth, C.W.; Fife, K.W.; Nielsen, J.B.; Pierce, S.W.; Ricketts, T.E.; Rink, N.A.; Robinson, M.A.

    1996-08-01

    This report documents progress on the Los Alamos Nuclear Materials Stabilization and Packaging projects for the second quarter of FY 1996. It covers development and production activities for the Plutonium Packaging Project, the Plutonium Recovery and Processing Project, and the Uranium Recovery and Processing Project. In addition, it reports on quality assurance activities for the Plutonium Packaging Project.

  20. The Use of Films as Suitable Packaging Materials for Minimally Processed Foods

    Science.gov (United States)

    1994-08-01

    Freshly Peeled citrus products combine pectinase solution, vacuum infusion technology, and a mechanized line to produce pre- peeled orange and...PROCESSED FOODS: MODIFIED ATMOSPHERE PACKAGING, SOUS-VIDE, MICHOWAVEABLE FOODS nwvKrrvE POOD PRESERVATION, VENTED FOODS, ANTIBACTERIAL OXYGEN...Vented Foods Antibacterial Packaging Materials Oxygen Absorbers Moisture Absorbers Packaging Design and Environmental Concern/Awareness Edible Barrier

  1. 78 FR 29016 - Establishing Quality Assurance Programs for Packaging Used in Transport of Radioactive Material

    Science.gov (United States)

    2013-05-16

    ... Transport of Radioactive Material AGENCY: Nuclear Regulatory Commission. ACTION: Draft regulatory guide... regulations for the packaging and transportation of radioactive material. The NRC is issuing for public... in Transport of Radioactive Material.'' This draft regulatory guide describes a proposed method...

  2. Photoelasticity analysis of thermal stresses in the plastic ICs. Hikari danseiho ni yoru IC package nai oryoku no keisoku

    Energy Technology Data Exchange (ETDEWEB)

    Hasegawa, T.; Shibuya, Y. (Mitsubishi Electric Corp., Tokyo (Japan))

    1992-10-20

    Recent highly integrated semiconductors have tendencies of being finer patterns and larger silicon chip area. Plastic packages excellent in productivity have been proved to be highly reliable in moisture resistance due to improved sealing resin and have become the main part of IC packages. However, in such devices featuring larger chip area and finer circuit pattern as large capacity memories, the problem of internal stress due to sealing resin contraction has been highlighted as a new problem. In this study, a photoelasticity which is a relatively simple method is employed to evaluate stress within sealing resin, and the review on effects of stress on the interior of sealing resin and chip are reported. Further, the effect of a buffer coat formed on the chip to reduce the stress on a silicon chip, and the effect of package shape on the thermal stress has been examined by means of photoelasticity, and the result is also shown. 10 refs., 18 figs., 2 tabs.

  3. Determination of Polymer Additives-Antioxidants, Ultraviolet Stabilizers, Plasticizers and Photoinitiators in Plastic Food Package by Accelerated Solvent Extraction Coupled with High-Performance Liquid Chromatography.

    Science.gov (United States)

    Li, Bo; Wang, Zhi-Wei; Lin, Qin-Bao; Hu, Chang-Ying; Su, Qi-Zhi; Wu, Yu-Mei

    2015-07-01

    An analytical method for the quantitative determination of 4 antioxidants, 9 ultraviolet (UV) stabilizers, 12 phthalate plasticizers and 2 photoinitiators in plastic food package using accelerated solvent extraction (ASE) coupled with high-performance liquid chromatography-photodiode array detector (HPLC-PDA) has been developed. Parameters affecting the efficiency in the process such as extraction and chromatographic conditions were studied in order to determine operating conditions. The analytical method of ASE-HPLC showed good linearity with good correlation coefficients (R ≥ 0.9833). The limits of detection and quantification were between 0.03 and 0.30 µg mL(-1) and between 0.10 and 1.00 µg mL(-1) for 27 analytes. Average spiked recoveries for most analytes in samples were >70.4% at 10, 20 and 40 µg g(-1) spiked levels, except UV-9 and Irganox 1010 (58.6 and 64.0% spiked at 10 µg g(-1), respectively), the relative standard deviations were in the range from 0.4 to 15.4%. The methodology has been proposed for the analysis of 27 polymer additives in plastic food package. © The Author 2014. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  4. Renewable fibers and bio-based materials for packaging applications - A review of recent developments

    DEFF Research Database (Denmark)

    Johansson, Caisa; Bras, Julien; Mondragon, Inaki

    2012-01-01

    materials in the packaging market. The covered subjects are renewable fibers and bio-based polymers for use in bioplastics or as coatings for paper-based packaging materials. Current market sizes and forecasts are also presented. Competitive mechanical, thermal, and barrier properties along with material...

  5. 77 FR 14445 - Leakage Tests on Packages for Shipment of Radioactive Material

    Science.gov (United States)

    2012-03-09

    ... COMMISSION Leakage Tests on Packages for Shipment of Radioactive Material AGENCY: Nuclear Regulatory... Standard N14.5-1997, ``Radioactive Materials--Leakage Tests on Packages for Shipment'' approved February... receiving radioactive material. II. Further Information Revision 1 of Regulatory Guide 7.4 was issued with...

  6. Automobile materials competition: energy implications of fiber-reinforced plastics

    Energy Technology Data Exchange (ETDEWEB)

    Cummings-Saxton, J.

    1981-10-01

    The embodied energy, structural weight, and transportation energy (fuel requirement) characteristics of steel, fiber-reinforced plastics, and aluminum were assessed to determine the overall energy savings of materials substitution in automobiles. In body panels, a 1.0-lb steel component with an associated 0.5 lb in secondary weight is structurally equivalent to a 0.6-lb fiber-reinforced plastic component with 0.3 lb in associated secondary weight or a 0.5-lb aluminum component with 0.25 lb of secondary weight. (Secondary weight refers to the combined weight of the vehicle's support structure, engine, braking system, and drive train, all of which can be reduced in response to a decrease in total vehicle weight.) The life cycle transportation energy requirements of structurally equivalent body panels (including their associated secondary weights) are 174.4 x 10/sup 3/ Btu for steel, 104.6 x 10/sup 3/ Btu for fiber-reinforced plastics, and 87.2 x 10/sup 3/ Btu for aluminum. The embodied energy requirements are 37.2 x 10/sup 3/ Btu for steel, 22.1 x 10/sup 3/ Btu for fiber-reinforced plastics, and 87.1 x 10/sup 3/ Btu for aluminum. These results can be combined to yield total energy requirements of 211.6 x 10/sup 3/ Btu for steel, 126.7 x 10/sup 3/ Btu for fiber-reinforced plastics, and 174.3 x 10/sup 3/ Btu for aluminum. Fiber-reinforced plastics offer the greatest improvements over steel in both embodied and total energy requirements. Aluminum achieves the greatest savings in transportation energy.

  7. Strength of anisotropic wood and synthetic materials. [plywood, laminated wood plastics, glass fiber reinforced plastics, polymeric film, and natural wood

    Science.gov (United States)

    Ashkenazi, Y. K.

    1981-01-01

    The possibility of using general formulas for determining the strength of different anisotropic materials is considered, and theoretical formulas are applied and confirmed by results of tests on various nonmetallic materials. Data are cited on the strength of wood, plywood, laminated wood plastics, fiber glass-reinforced plastics and directed polymer films.

  8. Analysis of phthalates in food products and packaging materials sold on the Belgian market.

    Science.gov (United States)

    Fierens, T; Servaes, K; Van Holderbeke, M; Geerts, L; De Henauw, S; Sioen, I; Vanermen, G

    2012-07-01

    Phthalates are organic lipophilic compounds that are principally used as plasticiser to increase the flexibility of plastic polymers. Other applications are a.o. the use of phthalates in printing inks and lacquers. Human exposure to phthalates mainly occurs via food ingestion and can induce adverse health effects. In this study, the presence of eight phthalate compounds--dimethyl phthalate (DMP), diethyl phthalate (DEP), diisobutyl phthalate (DiBP), di-n-butyl phthalate (DnBP), benzylbutyl phthalate (BBP), di(2-ethylhexyl) phthalate (DEHP), dicyclohexyl phthalate (DCHP) and di-n-octyl phthalate (DnOP)--was investigated in 400 food products, divided over eleven groups, and packages sold on the Belgian market. For this purpose, suitable extraction techniques were developed and validated for four different matrices, namely high-fat foods, low-fat food products, aqueous-based beverages and packaging materials. The instrumental analysis was performed by means of gas chromatography-low resolution-mass spectrometry with electron impact ionisation (GC-EI-MS). A wide variety of phthalate concentrations was observed in the different groups. DEHP was found in the highest concentration in almost every group. Moreover, DEHP was the most abundant phthalate compound, followed by DiBP, DnBP and BBP. This survey is part of the PHTAL project, which is the first project that discusses phthalate contamination on the Belgian food market.

  9. YPHON: A package for calculating phonons of polar materials

    Science.gov (United States)

    Wang, Yi; Chen, Long-Qing; Liu, Zi-Kui

    2014-11-01

    In our recent works, we have developed a mixed-space approach within the framework of direct method for the first-principle calculation of phonon properties. It makes full use of the accuracy of the force constants calculated in the real space and the dipole-dipole interactions in the reciprocal space, making the accurate phonon calculation possible with the direct method for polar materials. In this paper, an efficient C++ implementation of the mixed-space approach, YPHON, is provided as open source, including demos and Linux scripts for extracting input data to YPHON from the output of VASP.5. The functions of the current package include the calculations of: (1) the phonon dispersions; (2) the phonon density of states; (3) the neutron scattering section weighted phonon density of state; (4) the phonons of the high symmetry structure using the force constants from low symmetry structure; (5) the phonon dispersions of random alloys; and (6) the analysis of the vibrational modes using the point group theory. Catalogue identifier: AETS_v1_0 Program summary URL:http://cpc.cs.qub.ac.uk/summaries/AETS_v1_0.html Program obtainable from: CPC Program Library, Queen’s University, Belfast, N. Ireland Licensing provisions: Standard CPC licence, http://cpc.cs.qub.ac.uk/licence/licence.html No. of lines in distributed program, including test data, etc.: 567815 No. of bytes in distributed program, including test data, etc.: 9763594 Distribution format: tar.gz Programming language: C++, Linux scripts. Computer: Linux systems with a g++ or C++ compiler. Operating system: Linux. RAM: Ranges from a few Mbytes to a few Gbytes, dynamically depending on the system size. Classification: 7.8. External routines: GSL-the GNU Scientific Library (GSL) is a numerical library for C and C++ programmers. VASP.5 or later for the calculations of force constants and dielectric constants and Born effective charge for polar materials. Nature of problem: This package has the purpose of computing

  10. Chemical characteristics and fatty acid composition on oils and fats stored in different packaging materials

    Directory of Open Access Journals (Sweden)

    El-Shattory, Y.

    1996-12-01

    Full Text Available Bleached cottonseed oil, partially hydrogenated palm oil and margarine were stored in metal (tin cans and white plastic (polyethylene bottles with air in head space and served at room temperature during the whole period of investigation. The analytical techniques used to analyse these materials has been done at zero time storing (control, after four and seven months of storage. This study showed that storing oils in metal cans have better results than plastic packages specially for bleached cottonseed and hydrogenated oils.

    Aceite de semilla de algodón decolorado, aceite de palma parcialmente hidrogenado y margarina fueron almacenados en latas metálicas (estaño y en botellas de plástico blanco (polietileno con aire en el espacio de cabeza y a temperatura ambiente durante todo el período de investigación. Las técnicas analíticas usadas para analizar estos materiales fueron ensayados a tiempo cero de almacenamiento (control, y después de cuatro y siete meses de almacenamiento. Este estudio mostró que los aceites almacenados en latas metálicas tienen mejores resultados que los envases de plástico, especialmente para los aceites hidrogenados y de semilla de algodón decolorado.

  11. ROCK FALL CALCULATIONS FOR SINGLE CORROSION RESISTANT MATERIAL WASTE PACKAGES

    Energy Technology Data Exchange (ETDEWEB)

    Z. Ceylan

    1999-03-23

    The purpose of this activity is to determine the structural performance of waste packages (WP) subject to rock fall design basis event (DBE) dynamic loads and document the calculation results that describe the threshold rock sizes for crack-initiation and through cracks in waste package shells. This activity is associated with the waste package design. AP-3.12Q, Revision 0, ICN 0, Calculations, is used to develop the calculation.

  12. ROCK FALL CALCULATIONS FOR SINGLE CORROSION RESISTANT MATERIAL WASTE PACKAGES

    Energy Technology Data Exchange (ETDEWEB)

    S. Bader

    1999-09-20

    The purpose of this activity is to determine the structural performance of waste packages (WP) subject to rock fall design basis event (DBE) dynamic loads and document the calculation results that describe the threshold rock sizes for crack-initiation and through-cracks in waste package shells. This activity is associated with the waste package design. AP-3.12Q, Revision 0, ICN 0, Calculations, is used to develop the calculation.

  13. Thermoforming and Its Application in Plastics Packaging of Two Way Radio%吸塑成型及其在手持机塑料包装中的应用

    Institute of Scientific and Technical Information of China (English)

    徐中亮

    2015-01-01

    吸塑成型是一种塑料制品快速成型的方法。本文以手持机的塑料包装为研究对象,阐述了吸塑成型技术的原理和工艺,并探讨了优选热塑性材料、最优化塑料包装的结构尺寸、吸塑模具设计加工对吸塑工艺影响。从而,提高塑料包装的可靠性,延长使用寿命,降低包装的成本,并广泛应用于手持机的塑料包装设计中。%Thermoforming is a kind of method that plastics products fast forming. The article is based on plastics packaging of handheld two way radio, elaborating theory and methods of plastics forming techniques, while researching on that selecting the priority material of thermoplastic. optimizing the configuration dimension of plastics packaging, designing and processing for blister mold what they are on the influence of blister-technics. Thereby, it can highly improve product reliability, increase service life, reduce the cost price of product, widely apply for plastics packaging of two way radio.

  14. Influence of protective characteristics of packaging material on packed dried fruits

    Directory of Open Access Journals (Sweden)

    Gvozdenović Jasna J.

    2007-01-01

    Full Text Available Dried fruits are very delicate to biochemical changes during storage, due to low water content, as well as low aw value. The shelf life of these products depends on aw value. Materials for dry fruits packaging are necessary to have appropriate barrier characteristics for water, oxygen, nitrogen and carbon dioxide molecules, as well as for electromagnetic rays, especially those with low wavelengths in UV region. During storage of packed dry fruits, qualitative changes, influenced by different packaging materials, may occur. The results of tested characteristics of different packaging materials, combination and their barrier features, as well as the qualitative changes of packaged dried apples are presented in this paper. The qualitative changes of color and sensory characteristics of packaged dried apples point out to influence of the type, combination as well as the barrier features of used packaging materials. .

  15. Quality and safety aspects of meat products as affected by various physical manipulations of packaging materials.

    Science.gov (United States)

    Lee, Keun Taik

    2010-09-01

    This article explores the effects of physically manipulated packaging materials on the quality and safety of meat products. Recently, innovative measures for improving quality and extending the shelf-life of packaged meat products have been developed, utilizing technologies including barrier film, active packaging, nanotechnology, microperforation, irradiation, plasma and far-infrared ray (FIR) treatments. Despite these developments, each technology has peculiar drawbacks which will need to be addressed by meat scientists in the future. To develop successful meat packaging systems, key product characteristics affecting stability, environmental conditions during storage until consumption, and consumers' packaging expectations must all be taken into consideration. Furthermore, the safety issues related to packaging materials must also be taken into account when processing, packaging and storing meat products.

  16. Reliable liquid chromatography-mass spectrometry method for investigation of primary aromatic amines migration from food packaging and during industrial curing of multilayer plastic laminates.

    Science.gov (United States)

    Lambertini, Francesca; Di Lallo, Valentina; Catellani, Dante; Mattarozzi, Monica; Careri, Maria; Suman, Michele

    2014-09-01

    Primary aromatic amines (PAAs) can migrate from packaging into food from different sources such as polyurethanic adhesives used for the manufacture of multilayer films, which may contain residual aromatic isocyanates, or recycled paperboard, because of the presence of azo dyes in the printed paper massively used in the recycling process. In the present work, a reliable analytical method, exploiting a conventional high-performance liquid chromatography-(selected ion monitoring)-mass spectrometry system, for PAAs compliance assessment in food contact materials was developed as an effective alternative to the current standard spectrophotometric one, moving in this way from the screening to the accurate and selective quantitation perspective for the analysis of PAAs both in aqueous and acidic food simulants. The main validation parameters were verified achieving very satisfactory results in terms of linearity range, limit of detection (ranging from 0.1 to 1.0 µg kg(-1)) and quantitation (ranging from 0.1 to 3.6 µg kg(-1)), repeatability and accuracy. Suitability of the method was demonstrated for a wide range of commercial samples, chosen among different producers of the most common used food packaging plastic and paperboard categories and then analyzed to assess the risk related to PAAs migration. Finally, the method was also successfully exploited to monitor the evolution of potential PAAs migration during the industrial curing process of multilayer plastic laminates, prior to their release for delivery to the food industry end user.

  17. 基于食品安全的塑料食品包装设计研究%Plastic Food Packaging Design Research Based on Food Safety

    Institute of Scientific and Technical Information of China (English)

    张继斌

    2016-01-01

    Food packaging determines the food quality and safety in the circulation process condition. There-fore, the packaging material and technology can better guarantee food quality, which prolong its storage time in safety. This paper focused on the food safety issues based on the food is easy to be affected with damp. The food moisture-proof packaging storage time prediction model was proposed. The model was used for analyzing the damp time and the balance state of moisture absorption, which provd its feasibility. Finally according to the structure and function of the food plastic packaging design demand, proposed a kind of food packaging system software design and development methods.%食品包装决定了食品在流通过程中的质量及安全状况,因此研究包装材料及技术,能够更好的保障食品质量,延长其在安全范围内的存储时间.针对食品易受潮这一具有代表性的食品安全问题进行研究,提出了食品防潮包装的存储时间预测模型,并使用该模型对膨化食品受潮时间及吸湿平衡状态进行计算分析,证明该模型的可行性.最后根据食品塑料包装设计的结构及功能需求,提出一种食品包装系统软件设计及开发的方法.

  18. 49 CFR 173.419 - Authorized packages-oxidizing Class 7 (radioactive) materials.

    Science.gov (United States)

    2010-10-01

    ... SHIPPERS-GENERAL REQUIREMENTS FOR SHIPMENTS AND PACKAGINGS Class 7 (Radioactive) Materials § 173.419 Authorized packages—oxidizing Class 7 (radioactive) materials. (a) An oxidizing Class 7 (radioactive... 49 Transportation 2 2010-10-01 2010-10-01 false Authorized packages-oxidizing Class 7...

  19. [Study of relationship between consumption of potassium permanganate and total organic carbon on plastic kitchen utensils, food packages and toys].

    Science.gov (United States)

    Ohno, Hiroyuki; Suzuki, Masako; Mutsuga, Motoh; Kawamura, Yoko

    2009-10-01

    Consumption of potassium permanganate and total organic carbon (TOC) were investigated as indices of total organic matter migrated into water from plastic kitchen utensils, food packages and toys for children. The samples were soaked in water at 60 or 95 degrees C for 30 min for kitchen utensils and food packages, and at 40 degrees C for 30 min for toys and the eluates were examined, using the two indices. The quantitation limits were both 0.5 microg/mL. Among 97 kitchen utensils and food packages tested, consumption of potassium permanganate and TOC were 0.5-10.9 microg/mL and ND-18.9 microg/mL for polyvinyl chloride (PVC) tea-pot spouts and nylon kitchen utensils, respectively. Among 32 toys tested, the levels were 0.8-45.5 microg/mL and 0.5-8.9 microg/mL from PVC toys and block toys made by ethylene vinyl acetate resin. The levels for other samples were very low. There were large discrepancies between consumption of potassium permanganate and TOC for some PVC products and nylon kitchen utensils. The cause may be a marked difference of the oxidation decomposition rate by potassium permanganate, depending on the kind of organic matter that migrated from the plastics.

  20. RENEWABLE FIBERS AND BIO-BASED MATERIALS FOR PACKAGING APPLICATIONS – A REVIEW OF RECENT DEVELOPMENTS

    Directory of Open Access Journals (Sweden)

    Caisa Johansson,

    2012-04-01

    Full Text Available This review describes the state-of-the-art of material derived from the forest sector with respect to its potential for use in the packaging industry. Some innovative approaches are highlighted. The aim is to cover recent developments and key challenges for successful introduction of renewable materials in the packaging market. The covered subjects are renewable fibers and bio-based polymers for use in bioplastics or as coatings for paper-based packaging materials. Current market sizes and forecasts are also presented. Competitive mechanical, thermal, and barrier properties along with material availability and ease of processing are identified as fundamental issues for sustainable utilization of renewable materials.

  1. Elastic, plastic, and fracture mechanisms in graphene materials.

    Science.gov (United States)

    Daniels, Colin; Horning, Andrew; Phillips, Anthony; Massote, Daniel V P; Liang, Liangbo; Bullard, Zachary; Sumpter, Bobby G; Meunier, Vincent

    2015-09-23

    In both research and industry, materials will be exposed to stresses, be it during fabrication, normal use, or mechanical failure. The response to external stress will have an important impact on properties, especially when atomic details govern the functionalities of the materials. This review aims at summarizing current research involving the responses of graphene and graphene materials to applied stress at the nanoscale, and to categorize them by stress-strain behavior. In particular, we consider the reversible functionalization of graphene and graphene materials by way of elastic deformation and strain engineering, the plastic deformation of graphene oxide and the emergence of such in normally brittle graphene, the formation of defects as a response to stress under high temperature annealing or irradiation conditions, and the properties that affect how, and mechanisms by which, pristine, defective, and polycrystalline graphene fail catastrophically during fracture. Overall we find that there is significant potential for the use of existing knowledge, especially that of strain engineering, as well as potential for additional research into the fracture mechanics of polycrystalline graphene and device functionalization by way of controllable plastic deformation of graphene.

  2. Packaging material and flexible medical tubing containing thermally exfoliated graphite oxide

    Science.gov (United States)

    Prud'homme, Robert K. (Inventor); Aksay, Ilhan A. (Inventor)

    2011-01-01

    A packaging material or flexible medical tubing containing a modified graphite oxide material, which is a thermally exfoliated graphite oxide with a surface area of from about 300 m.sup.2/g to 2600 m.sup.2/g.

  3. Information technologies and software packages for education of specialists in materials science [In Russian

    NARCIS (Netherlands)

    V. Krzhizhanovskaya; S. Ryaboshuk

    2009-01-01

    This paper presents methodological materials, interactive text-books and software packages developed and extensively used for education of specialists in materials science. These virtual laboratories for education and research are equipped with tutorials and software environment for modeling complex

  4. The impact of policy interactions on the recycling of plastic packaging waste in Germany

    OpenAIRE

    Gandenberger, Carsten; Orzanna, Robert; Klingenfuß, Sara; Sartorius, Christian

    2014-01-01

    Due to the environmental challenges associated with the strong growth of plastic waste worldwide, the EU Commission recently published a green paper on a European Strategy on Plastic Waste in the Environment (COM (2013), 123 final), which highlights the challenges and opportunities that arise from improving the management of plastic waste in the EU. The European Waste Directive (2008/98/EC) which was transposed into German law through the Kreislaufwirtschaftsgesetz (KrWG) established the so-c...

  5. Legal analysis of information displayed on dental material packages: An exploratory research

    OpenAIRE

    Bhumika Rathore; Pusphpanjali Krishnappa; Suraj U Mehta

    2016-01-01

    Introduction: Some of the dental materials possess occupational hazards, preprocedural errors, and patient allergies as suggested by evidence. With due consideration to safety of the patients and dental professionals, it is essential that the trade of these materials is in conformity with the law. Aim: To perform the legal analysis of the information displayed on the packaging of dental materials. Materials and Methods: The Bureau of Indian Standards sets guidelines for packaging and marketin...

  6. Solvent extraction as additional purification method for postconsumer plastic packaging waste

    NARCIS (Netherlands)

    Thoden van Velzen, E.U.; Jansen, M.

    2011-01-01

    An existing solvent extraction process currently used to convert lightly polluted post-industrial packaging waste into high quality re-granulates was tested under laboratory conditions with highly polluted post-consumer packaging waste originating from municipal solid refuse waste. The objective was

  7. Solvent extraction as additional purification method for postconsumer plastic packaging waste

    NARCIS (Netherlands)

    Thoden van Velzen, E.U.; Jansen, M.

    2011-01-01

    An existing solvent extraction process currently used to convert lightly polluted post-industrial packaging waste into high quality re-granulates was tested under laboratory conditions with highly polluted post-consumer packaging waste originating from municipal solid refuse waste. The objective was

  8. Application of polymer nanocomposite materials in food packaging

    OpenAIRE

    Bratovčić, Amra; Odobašić, Amra; Ćatić, S.; Šestan, Indira

    2015-01-01

    The term “nano” refers to nano particle size from 1 to 100 nanometers. The term "nanotechnology" was first introduced by Norio Taniguchi in 1974. Nanotechnology may be used to improve the taste and texture of food and for the production of packaging that maintain fresh product. The primary function of packaging is to maintain the quality and safety of products during transport and storage period, as well as to extend its viability by preventing unwanted effect agents such as microorganisms, c...

  9. 塑料食品包装中邻苯二甲酸酯类塑化剂含量调查%Investigation on the content of phthalate acid esters plasticizers in plastic food packaging

    Institute of Scientific and Technical Information of China (English)

    陈明; 商贵芹; 王红松

    2013-01-01

    Objective To understand the situation of 18 kinds of phthalic acid esters in plastic food packaging.Methods The contents of phthalic acid esters in 280 plastic food packaging of different materials were analyzed by gas chromatography-mass spectrometry (GC-MS) following standard GB/T 21928-2008.The samples were extracted ultrasonically with n-hexane,then separated by HP-5MS capillary column and detected by single quadrupole mass spectrometry.Retention time and characteristic ions were used as qualitative evidence,and external standard was used for quantification.Results The content of 18 kinds of phthalate in 95% of the 62 batches of PVC materials were qualified,all 82 batches of composite materials and 136 batches of other materials were qualified.Diethylhexylphthalate residues were detected,and seriously exceeded the standard limit in 3 polyvinyl chloride materials.Conclusion The phthalic acid esters exposure from plastic food packaging was low,while polyvinyl chloride materials put a potential health risk to human.Regulation and monitoring on phthalic acid esters in plastic food packaging should be strengthened.%目的 了解塑料食品包装中18种邻苯二甲酸酯的含量现状.方法 选取280批不同材质的塑料食品包装,依据GB/T 21928-2008《食品塑料包装材料中邻苯二甲酸酯的测定》采用气相色谱-质谱法进行检测.以正已烷为提取溶剂,超声波提取,采用HP-5MS石英毛细管柱(30 m×0.25 mm,0.25 μm)色谱柱程序升温分离,以保留时间和特征离子为定性依据,外标法定量.结果 62批聚氯乙烯材质的食品包装中18种邻苯二甲酸酯含量95%小于法规限量,82批复合材质和136批其它材质的食品包装中18种邻苯二甲酸酯含量100%小于法规限量,检出最多的是邻苯二甲酸二(2-乙基)己酯,3批聚氯乙烯材质的食品包装中邻苯二甲酸二(2-乙基)己酯严重超标.结论 塑料食品包装中邻苯二甲酸酯暴露水平较低,聚氯乙烯

  10. Materials in Manufacturing and Packaging Systems as Sources of Elemental Impurities in Packaged Drug Products: A Literature Review.

    Science.gov (United States)

    Jenke, Dennis R; Stults, Cheryl L M; Paskiet, Diane M; Ball, Douglas J; Nagao, Lee M

    Elemental impurities in drug products can arise from a number of different sources and via a number of different means, including the active pharmaceutical ingredient, excipients, the vehicle, and leaching of elemental entities that are present in the drug product's manufacturing or packaging systems. Thus, knowledge about the presence, level, and likelihood of leaching of elemental entities in manufacturing and packaging systems is relevant to understanding how these systems contribute to a drug product's total elemental impurity burden. To that end, a joint team from the Extractables and Leachables Safety Information Exchange (ELSIE) Consortium and the International Pharmaceutical Aerosol Consortium on Regulation and Science (IPAC-RS) has conducted a review of the available literature on elemental entities in pharmaceutically relevant polymers and the presence of these elemental entities in material extracts and/or drug products. This review article contains the information compiled from the available body of literature and considers two questions: (1) What elemental entities are present in the relevant polymers and materials and at what levels are they present? (2) To what extent are these elemental entities leached from these materials under conditions relevant to the manufacturing and storage/distribution of solution drug products? Conclusions drawn from the compiled data are as follows: (1) Elemental entities are present in the materials used to construct packaging and manufacturing systems as these materials either contain these elemental entities as additives or are exposed to elemental entities during their production. (2) Unless the elemental entities are parts of the materials themselves (for example, SiO2 in glass) or intentionally added to the materials (for example, metal stearates in polymers), their incidental amounts in the materials are generally low. (3) When elemental entities are present in materials and systems, generally only a very small

  11. Elucidating the role of interfacial materials properties in microfluidic packages.

    Energy Technology Data Exchange (ETDEWEB)

    Edwards, Thayne L.

    2013-01-01

    The purpose of this work was to discover a method to investigate the properties of interfaces as described by a numerical physical model. The model used was adopted from literature and applied to a commercially available multiphysics software package. By doing this the internal properties of simple structures could be elucidated and then readily applied to more complex structures such as valves and pumps in laminate microfluidic structures. A numerical finite element multi-scale model of a cohesive interface comprised of heterogeneous material properties was used to elucidate irreversible damage from applied strain energy. An unknown internal state variable was applied to characterize the damage process. Using a constrained blister test, this unknown internal state variable could be determined for an adherend/adhesive/adherend body. This is particularly interesting for laminate systems with microfluidic and microstructures contained within the body. A laminate structure was designed and fabricated that could accommodate a variety of binary systems joined using nearly any technique such as adhesive, welding (solvent, laser, ultrasonic, RF, etc.), or thermal. The adhesive method was the most successful and easy to implement but also one of the more difficult to understand, especially over long periods of time. Welding methods are meant to achieve a bond that is similar to bulk properties and so are easier to predict. However, methods of welding often produce defects in the bonds.. Examples of the test structures used to elucidate the internal properties of the model were shown and demonstrated. The real life examples used this research to improve upon current designs and aided in creating complex structures for sensor and other applications.

  12. Radiation modified sago-blends and its potential for biodegradable packaging materials

    Energy Technology Data Exchange (ETDEWEB)

    Ghazali, Z.; Idris, S.; Dahlan, K.Z. [Malaysian Institute for Nuclear Technology Research, Bangi, Kajang (Malaysia); Wongsuban, B.; Adzahan, N.M.; Ithnin, L. [Universiti Putra Malaysia, Faculty of Food Science and Biotechnology, Serdang (Malaysia)

    2002-03-01

    This paper describes work at MINT on the characterisation and development of sago blends as alternative biodegradable packaging materials. A study was undertaken to investigate the effect of formulation, mixing temperature and irradiation dosage on expansion of sago starch-polyvinyl alcohol (PVA) and sago-polyvinyl pyrrolidone (PVP) blends based foam. The foams were produced by microwaving irradiated hydrogels prepared by mixing sago starch with aqueous PVA or PVP. In the development of starch-based plastic, the effect of different composition and different irradiation dosage were studied to evaluate films with good tensile properties, elongation, gas permeability and water vapor transmission rate and also the biodegradability of the film using soil burial test. In another development, irradiation i.e. microwave, electron beam and gamma, has been investigated as a means of degrading the starch granules, which leads to an increase in the amount soluble materials leached. Results showed that irradiation caused an increase in leaching, and a concomitant drastic reduction in swelling volumes of starch granules. It is also showed that the strength of starch gels and viscosity decreased as the levels of irradiation was increased. The degraded starches will be incorporated as an ingredient in the fish cracker and characterized its properties. (author)

  13. Determination of free and total phthalates in commercial whole milk products in different packaging materials by gas chromatography-mass spectrometry.

    Science.gov (United States)

    Lin, Jialu; Chen, Wanxin; Zhu, Hangcui; Wang, Chengjun

    2015-12-01

    We developed a method for extraction and determination of free and total phthalate esters in commercial whole milk products. The free phthalates in milk samples were extracted with ethyl acetate after general pretreatment procedures including protein precipitation, centrifugation, and filtration. The bound phthalates in samples were first desorbed with the aid of ultrasound irradiation before extraction of total phthalates. The separation and determination of phthalates in extracts was performed by gas chromatography coupled with mass spectrometric detection. The detection limits were in the range of 0.09 to 0.36ng/g and the average recovery between 79.1 and 110.3%. The developed methods were applied to extract and determine phthalates in commercial whole milk products with different packaging materials, including plastic, glass, and metal. All samples contained several phthalates, including diethyl, diisobutyl, and bis(2-ethylhexyl) phthalates at concentrations between 2.60 and 156.4ng/g. The identified phthalates occurred in both free and bound forms. The amounts of phthalates in milk samples packaged in glass and metal containers were much lower than those in plastic containers. Plastic packaging materials are a possible source of phthalate contamination in commercial whole milk products, and a considerable portion of bleached phthalates from packaging can be adsorbed on proteins and other solid components of milk.

  14. 邻苯二甲酸二(2-乙基己基)酯在广式腊肠中的迁移特性%Migration of plasticizer di-2-ethylhexyl phthalate from PVC packaging material into cured meat

    Institute of Scientific and Technical Information of China (English)

    陈海光; 肖乃玉; 刘朝霞; 谭贵良; 刘垚

    2011-01-01

    利用增塑剂DEHP的皂化反应,采用膜/肉接触的比色管模式和气相色谱法,研究了温度、时间、脂肪含量和加工方式等因素对PVC膜中的增塑剂DEHP向广式腊肠迁移的影响。结果表明:随着温度的升高,时间的延长,脂肪含量的增加,DEHP向肉中的迁移量均会增大;在紫外照射、微波辐射和高温蒸煮等条件下,DEHP的迁移量也会增加,其中微波辐射的作用较为明显,如微波照射18 s后,DEHP的迁移量高达189.3342 mg/kg,紫外光照射48 h后,迁移量是173.5921 mg/kg。同时研究了DEHP迁移溶出后,PVC%The migration of plasticizer di-2-ethylhexyl phthalate(DEHP)existing in food packaging PVC film into Guangdong style sausage(GSS),was studied by the saponification reaction of DEHP,and the influence of temperature,time,fat content and processing method was also investigated by using the model of colorimetric tube of film/meat contact.The results indicated that the higher the temperature,the longer the time and the more the fat content,the faster the migration was.It showed that ultraviolet irradiation and microwave heating could enhance the migration of DEHP from PVC film into meat.After microwave heating for 18 s,the amount of migration of DEHP was 189.3342 mg/kg,while the amount of migration of DEHP was 173.5921 mg/kg after ultraviolet irradiation for 48 h.PVC film mechanical properties,and penetration of oxygen and moisture were studied after migration of plasticizer DEHP from PVC into GSS.It was observed that with the transfer of DEHP the power of pulling and breaking changed in PVC film,and the transfer of air and moisture distinctly decreased.

  15. Compilation of current literature on seals, closures, and leakage for radioactive material packagings

    Energy Technology Data Exchange (ETDEWEB)

    Warrant, M.M.; Ottinger, C.A.

    1989-01-01

    This report presents an overview of the features that affect the sealing capability of radioactive material packagings currently certified by the US Nuclear Regulatory Commission. The report is based on a review of current literature on seals, closures, and leakage for radioactive material packagings. Federal regulations that relate to the sealing capability of radioactive material packagings, as well as basic equations for leakage calculations and some of the available leakage test procedures are presented. The factors which affect the sealing capability of a closure, including the properties of the sealing surfaces, the gasket material, the closure method and the contents are discussed in qualitative terms. Information on the general properties of both elastomer and metal gasket materials and some specific designs are presented. A summary of the seal material, closure method, and leakage tests for currently certified packagings with large diameter seals is provided. 18 figs., 9 tabs.

  16. Migration and sensory changes of packaging materials caused by ionising radiation

    Science.gov (United States)

    Welle, Frank; Mauer, Alexandra; Franz, Roland

    2002-03-01

    Irradiation of packaging materials—in most cases plastics—generally lead to a formation of free radicals and ions, with secondary effects such as cross-linking as well as oxidative chain scission. These effects result in a formation of volatile radiolysis products which may induce off-odours in the polymers and may change the migration characteristics of packaging materials. Irradiation affect also polymer additives which change the specific migration behaviour of polymer additives and additive related decomposition products. Migration and sensory changes of pre-sterilised packaging materials have consequences on the quality of packaged goods and consumer's safety. Therefore, migration and sensory properties of packaging materials have specific regulations. Within this paper the effects of the formation of radiolysis products on overall migration, specific migration of food additives or radiolysis products as well as on sensory changes are discussed in view of current European food law.

  17. Directory of certificates of compliance for radioactive materials packages

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-10-01

    The purpose of this directory is to make available a convenient source of information on packagings approved by the U.S. Nuclear Regulatory Commission. To assist in identifying packaging, an index by Model Number and corresponding Certificate of Compliance Number is included at the front of Volumes 1 and 2. An alphabetical listing by user name is included in the back of Volume 3 for approved Quality Assurance programs. The reports include a listing of all users of each package design and approved Quality Assurance programs prior to the publication date of the directory. Comments to make future revisions of this directory more useful are invited and should be directed to the Spent Fuel Project Office, U.S. Nuclear Regulatory Commission.

  18. COMPACTION OF FIBERBOARD OVERPACK MATERIALS IN A 9975 SHIPPING PACKAGE

    Energy Technology Data Exchange (ETDEWEB)

    Stefek, T.; Daugherty, W.; Estochen, E.; Murphy, J.

    2010-05-27

    Compaction of lower layers in the 9975 fiberboard overpack has been observed in packages that contain excess moisture. Dynamic loading of the package during transportation may also contribute to compaction of the fiberboard. This condition is being tested and analyzed to better understand these compaction mechanisms and provide a basis from which to evaluate their impact to the safety basis for transportation (Safety Analysis Report for Packaging) and storage (facility Design Safety Analysis) at the Savannah River Site (SRS). A test program has been developed and is being implemented to identify the extent of the compaction as a function of fiberboard moisture and typical transport dynamic loadings. Test conditions will be compared to regulatory requirements for dynamic loading. Characterization of the recovery of short-term compaction following the application of dynamic loading is also being evaluated. Interim results from this test program will be summarized.

  19. The profitability drivers in packaging materials reuse for manufacturers in business to business environments

    DEFF Research Database (Denmark)

    Larsen, Samuel; Deleuran, Brian; Jacobsen, Peter

    ’s theoretical basis is the RSC literature’s business perspective formulated by Guide and Van Wassenhove. Findings – The drivers of profitability in packaging materials reuse are 1) the amount of avoided costs of purchasing new packaging materials, 2) the firm’s ability to reduce costs of reverse logistics......Purpose –The purpose of this paper is to explore the profitability drivers for a firm’s operation of a reverse supply chain (RSC) that takes back and reuses packaging materials. Results apply specifically to original equipment manufacturers (OEMs) in business to business environments. Design...

  20. Mass Transfer Study of Chlorine Dioxide Gas Through Polymeric Packaging Materials

    Science.gov (United States)

    A continuous system for measuring the mass transfer of gaseous chlorine dioxide (ClO2), a strong oxidizing agent and used in food and pharmaceutical packaging, through 10 different types of polymeric packaging material was developed utilizing electrochemical sensor as a detector. Permeability, diff...

  1. Comparison of silicone and spin-on glass packaging materials for light-emitting diode encapsulation

    Energy Technology Data Exchange (ETDEWEB)

    Chang, Liann-Be; Pan, Ke-Wei; Yen, Chia-Yi [Department of Electronic Engineering and Green Technology Research Center, Chang Gung University, Taoyuan, Taiwan (China); Jeng, Ming-Jer, E-mail: mjjeng@mail.cgu.edu.tw [Department of Electronic Engineering and Green Technology Research Center, Chang Gung University, Taoyuan, Taiwan (China); Wu, Chun-Te; Hu, Sung-Cheng; Kuo, Yang-Kuao [Chemical Systems Research Division, Chung-Shan Institute of Science and Technology Armaments Bureau, MND, Taoyuan, Taiwan (China)

    2014-11-03

    Traditional white light light-emitting diode (LED) encapsulation is performed by mixed phosphors and silicone coating on LED die. However, this encapsulation with silicone coating incurs overheated temperatures and yellowing problem. Therefore, this work attempts to replace silicone paste by using spin-on-glass (SOG) materials. Experimental results indicate that although initial brightness of SOG-based packaging is lower than that of silicone packaging, its light attenuation is significantly lower than that of silicone for a long lighting time. After the LED power is turned on for 12 h, the brightness of LED with silicone and SOG material packaging decreases from 84 to 48 lm and 73 to 59 lm, respectively. Therefore, SOG material provides an alternative packaging solution for high power LED lighting applications. - Highlights: • Spin-on-glass (SOG) material was used to replace silicone coating for LED packaging. • Initial brightness of SOG packaging is lower than that of silicone packaging. • Over time, light attenuation in SOG is much lower than that in silicone. • Color rendering index and brightness of LED packaging was optimized by Taguchi method.

  2. 21 CFR 179.45 - Packaging materials for use during the irradiation of prepackaged foods.

    Science.gov (United States)

    2010-04-01

    ... PRODUCTION, PROCESSING AND HANDLING OF FOOD Packaging Materials for Irradiated Foods § 179.45 Packaging... chapter. (c) Ethylene-vinyl acetate copolymers complying with § 177.1350 of this chapter. The ethylene... exceed 1 pct by weight of the polymer. Triethylene glycol as described in § 178.3740(b) of this chapter...

  3. DEVELOPMENT OF A NEW TYPE A(F)RADIOACTIVE MATERIAL PACKAGING FOR THE DEPARTMENT OF ENERGY

    Energy Technology Data Exchange (ETDEWEB)

    Blanton, P.; Eberl, K.

    2008-09-14

    In a coordinated effort, the Department of Transportation (DOT) and Nuclear Regulatory Commission (NRC) proposed the elimination of the Specification Packaging from 49 CFR 173.[1] In accordance with the Federal Register, issued on October 1, 2004, new fabrication of Specification Packages would no longer be authorized. In accordance with the NRC final rulemaking published January 26, 2004, Specification Packagings are mandated by law to be removed from service no later than October 1, 2008. This coordinated effort and resulting rulemaking initiated a planned phase out of Specification Type B and Type A fissile (F) material transportation packages within the Department of Energy (DOE) and its subcontractors. One of the Specification Packages affected by this regulatory change is the UN1A2 Specification Package, per DOT 49 CFR 173.417(a)(6). To maintain continuing shipments of DOE materials currently transported in UN1A2 Specification Package after the existing authorization expires, a replacement Type A(F) material packaging design is under development by the Savannah River National Laboratory. This paper presents a summary of the prototype design effort and testing of the new Type A(F) Package development for the DOE. This paper discusses the progress made in the development of a Type A Fissile Packaging to replace the expiring 49 CFR UN1A2 Specification Fissile Package. The Specification Package was mostly a single-use waste disposal container. The design requirements and authorized radioactive material contents of the UN1A2 Specification Package were defined in 49 CFR. A UN1A2 Specification Package was authorized to ship up to 350 grams of U-235 in any enrichment and in any non-pyrophoric form. The design was specified as a 55-gallon 1A2 drum overpack with a body constructed from 18 gauge steel with a 16 gauge drum lid. Drum closure was specified as a standard 12-gauge ring closure. The inner product container size was not specified but was listed as any

  4. Interactions between six psychotherapeutic drugs and plastic containers. Influence of plastic material and infusion solutions.

    Science.gov (United States)

    Airaudo, C B; Gayte-Sorbier, A; Bianchi, C; Verdier, M

    1993-06-01

    The interactions of chlorpromazine, clomipramine, maprotiline and viloxazine hydrochlorides, and of clorazepate dipotassium salt and diazepam with polyvinyl chloride (PVC) and Stedim 6 infusion bags were studied. Stedim 6, is anew multilayer film whose inner layer is made of polyethylene. The drugs were in 5% dextrose and 0.9% sodium chloride isotonic solutions and the influence of these was also considered. The remaining concentrations of each drug were determined at regular time intervals in a 24-h period, by a spectrofluorometric method for chlorpromazine hydrochloride and by ultraviolet spectrophotometric methods for the other drugs. No binding was observed for viloxazine and maprotiline hydrochlorides whatever the infusion solution and the plastic container. A slight retention in PVC bags, but not in Stedim 6 ones, was noted for clomipramine hydrochloride and clorazepate dipotassium salt. This was more marked in the sodium chloride solution than in the dextrose one. Diazepam and chlorpromazine hydrochloride were bound both in PVC and Stedim 6 bags, but more in the former and more again in the sodium chloride solution than in the dextrose one. The results were explained in terms of the degree of crystallinity of the plastic material and the degree of lipophilicity of the drugs. Practical consequences are discussed.

  5. Alternative buffer material. Status of the ongoing laboratory investigation of reference materials and test package 1

    Energy Technology Data Exchange (ETDEWEB)

    Svensson, Daniel [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden); Dueck, Ann; Nilsson, Ulf; Olsson, Siv; Sanden, Torbjoern [Clay Technology AB, Lund (Sweden); Lydmark, Sara; Jaegerwall, Sara; Pedersen, Karsten [Microbial Analytics Sweden AB, Moelnlycke (Sweden); Hansen, Staffan [LTH Lund Univ., Lund (Sweden)

    2011-07-15

    Bentonite clay is part of the Swedish KBS-3 design of final repositories for high level radioactive waste. Wyoming bentonite with the commercial name MX-80 (American Colloid Co) has long been the reference for buffer material in the KBS-3 concept. Extending the knowledge base of alternative buffer materials will make it possible to optimize regarding safety, availability and cost. For this reason the field experiment Alternative Buffer Material (ABM) was started at Aespoe Hard Rock Laboratory during 2006. The experiment includes three medium-scale test packages, each consisting of a central steel tube with heaters, and a buffer of compacted clay. Eleven different clays were chosen for the buffers to examine effects of smectite content, interlayer cations and overall iron content. Also bentonite pellets with and without additional quartz are being tested. The buffer in package 1 had been subjected to wetting by formation water and heating for more than two years (at 130 deg C for {approx} 1 year) when it was retrieved and analyzed. The main purposes of the project were to characterise the clays with respect to hydro-mechanical properties, mineralogy and chemical composition and to identify any differences in behaviour or long term stability. The diversity of clays and the heater of steel also make the experiment suitable for studies of iron-bentonite interactions. This report concerns the work accomplished up to now and is not to be treated as any final report of the project.

  6. JUSTIFICATION FOR CHOOSING THE OPTIMAL PACKAGE OF MATERIALS FOR CLOTHING CHILDREN WITH METABOLIC SYNDROME

    OpenAIRE

    Ivashchenko I. N.

    2014-01-01

    Quality regulations of clothes and materials do not include features of children and adolescents with disorders of obesity in the design of clothes and selection of the materials. In the article, we proposed the choice of clothing materials management package with the structural features of the surface of the skin and subcutaneous tissue, the properties of materials and their functions

  7. Effects of flavour absorption on foods and their packaging materials

    NARCIS (Netherlands)

    Willige, van R.W.G.

    2002-01-01

    Keywords: flavour absorption, scalping, packaging, food matrix, lldpe, ldpe, pp, pc, pet, pen,b-lactoglobulin, casein, pectin, cmc, lactose, saccharose, oil, modelling, storage, oxygen permeability, taste perception,

  8. 75 FR 60333 - Hazardous Material; Miscellaneous Packaging Amendments

    Science.gov (United States)

    2010-09-30

    ... parties were given an opportunity to comment in response to the NPRM on the possible effect the removal of... were to go into effect, remanufactured drums not meeting minimum thickness requirements will have to be... the packaging, including the top and bottom, must have a minimum puncture resistance of 15 Joules...

  9. Influence of polystyrene and polyethylene packaging materials on food quality.

    NARCIS (Netherlands)

    Linssen, J.P.H.

    1992-01-01

    Polystyrene (PS) and polyethylene (PE) used for packaging of food were studied on their effect on product quality. Different types of PS were tested: General purpose polystyrene (GPPS), high impact polystyrene (HIPS, which contains a dispersed rubber phase) and several blends of these types. PS

  10. Effects of flavour absorption on foods and their packaging materials

    NARCIS (Netherlands)

    Willige, van R.W.G.

    2002-01-01

    Keywords: flavour absorption, scalping, packaging, food matrix, lldpe, ldpe, pp, pc, pet, pen,b-lactoglobulin, casein, pectin, cmc, lactose, saccharose, oil, modelling, storage, oxygen permeability, taste perception, sensory quality.Abso

  11. 49 CFR 173.21 - Forbidden materials and packages.

    Science.gov (United States)

    2010-10-01

    ... temperature-control procedures, and the written record of temperature measurements specified in paragraph (f... under controlled temperature conditions. The control temperature and emergency temperature for a package... must be initiated. § 173.21 Table: Method of Determining Control and Emergency Temperature. SADT...

  12. Biobased Packaging - Application in Meat Industry

    Directory of Open Access Journals (Sweden)

    S. Wilfred Ruban

    2009-04-01

    Full Text Available Because of growing problems of waste disposal and because petroleum is a nonrenewable resource with diminishing quantities, renewed interest in packaging research is underway to develop and promote the use of “bio-plastics.” In general, compared to conventional plastics derived from petroleum, bio-based polymers have more diverse stereochemistry and architecture of side chains which enable research scientists a greater number of opportunities to customize the properties of the final packaging material. The primary challenge facing the food (Meat industry in producing bio-plastic packaging, currently, is to match the durability of the packaging with product shelf-life. Notable advances in biopolymer production, consumer demand for more environmentally-friendly packaging, and technologies that allow packaging to do more than just encompass the food are driving new and novel research and developments in the area of packaging for muscle foods. [Vet. World 2009; 2(2.000: 79-82

  13. Carbon nanotubes for thermal interface materials in microelectronic packaging

    Science.gov (United States)

    Lin, Wei

    density was beneficial in increasing the collective thermal conductivity of the VACNT film; however, the increased tube-tube interaction in dense VACNT films decreased the thermal conductivity of the individual CNTs. The tip-to-tip contact resistance was shown to be ˜1x10-7 m2 K W -1. The study will shed light on the potential application of VACNTs as thermal interface materials in microelectronic packaging. 5. A combined process of in situ functionalization and microwave curing has been developed to effective enhance the interface between carbon nanotubes and the epoxy matrix. Effective medium theory has been used to analyze the interfacial thermal resistance between carbon nanotubes and polymer matrix, and that between graphite nanoplatlets and polymer matrix.

  14. Recycling of Plastic Packaging Wastes%塑料包装废弃物的再生利用

    Institute of Scientific and Technical Information of China (English)

    贺全国; 聂立波

    2011-01-01

    塑料包装在整个包装产业中占有极大比例,其废弃物的处理给国际社会减碳减排发展带来了巨大挑战。结合国内外对塑料包装废弃物的管理现状,分析了塑料包装废弃物的来源、分类和化学组成,阐述了国外塑料包装废弃物的回收分离技术和设备及国内相应研究现状;对塑料包装废弃物的再生利用途径进行深入解析,较全面地阐述了塑料包装废弃物再生利用的原理与研究现状;提出了塑料包装废弃物再生利用的基本策略建议。%The plastic packaging accounts for a very great proportion in the packaging industry,and the plastic packaging wastes(PPW) disposal brings great confrontation and challenge for global carbon emission reduction development.Based on the international practical PPW management,analyzes the source,classification and chemical composition for PPW and expounds the recycling separation technology and apparatus at aboard and the domestic research status;Resolves various PPW disposal approaches and elaborates comprehensively PPW regeneration principles and practices;Presents strategic suggestions on recycling and utilization of PPW.

  15. Short communication: Effect of active food packaging materials on fluid milk quality and shelf life.

    Science.gov (United States)

    Wong, Dana E; Goddard, Julie M

    2014-01-01

    Active packaging, in which active agents are embedded into or on the surface of food packaging materials, can enhance the nutritive value, economics, and stability of food, as well as enable in-package processing. In one embodiment of active food packaging, lactase was covalently immobilized onto packaging films for in-package lactose hydrolysis. In prior work, lactase was covalently bound to low-density polyethylene using polyethyleneimine and glutaraldehyde cross-linkers to form the packaging film. Because of the potential contaminants of proteases, lipases, and spoilage organisms in typical enzyme preparations, the goal of the current work was to determine the effect of immobilized-lactase active packaging technology on unanticipated side effects, such as shortened shelf-life and reduced product quality. Results suggested no evidence of lipase or protease activity on the active packaging films, indicating that such active packaging films could enable in-package lactose hydrolysis without adversely affecting product quality in terms of dairy protein or lipid stability. Storage stability studies indicated that lactase did not migrate from the film over a 49-d period, and that dry storage resulted in 13.41% retained activity, whereas wet storage conditions enabled retention of 62.52% activity. Results of a standard plate count indicated that the film modification reagents introduced minor microbial contamination; however, the microbial population remained under the 20,000 cfu/mL limit through the manufacturer's suggested 14-d storage period for all film samples. This suggests that commercially produced immobilized lactase active packaging should use purified cross-linkers and enzymes. Characterization of unanticipated effects of active packaging on food quality reported here is important in demonstrating the commercial potential of such technologies.

  16. Packaging strategies for printed circuit board components. Volume I, materials & thermal stresses.

    Energy Technology Data Exchange (ETDEWEB)

    Neilsen, Michael K. (Kansas City Plant, Kansas City, MO); Austin, Kevin N.; Adolf, Douglas Brian; Spangler, Scott W.; Neidigk, Matthew Aaron; Chambers, Robert S.

    2011-09-01

    Decisions on material selections for electronics packaging can be quite complicated by the need to balance the criteria to withstand severe impacts yet survive deep thermal cycles intact. Many times, material choices are based on historical precedence perhaps ignorant of whether those initial choices were carefully investigated or whether the requirements on the new component match those of previous units. The goal of this program focuses on developing both increased intuition for generic packaging guidelines and computational methodologies for optimizing packaging in specific components. Initial efforts centered on characterization of classes of materials common to packaging strategies and computational analyses of stresses generated during thermal cycling to identify strengths and weaknesses of various material choices. Future studies will analyze the same example problems incorporating the effects of curing stresses as needed and analyzing dynamic loadings to compare trends with the quasi-static conclusions.

  17. Impact of packaging material and storage time on olive oil quality ...

    African Journals Online (AJOL)

    Impact of packaging material and storage time on olive oil quality. ... appreciated for its characteristic flavor and its biological and nutritional value which are strongly related to the quality. ... EMAIL FREE FULL TEXT EMAIL FREE FULL TEXT

  18. Development of expert system for biobased polymer material selection: food packaging application.

    Science.gov (United States)

    Sanyang, M L; Sapuan, S M

    2015-10-01

    Biobased food packaging materials are gaining more attention owing to their intrinsic biodegradable nature and renewability. Selection of suitable biobased polymers for food packaging applications could be a tedious task with potential mistakes in choosing the best materials. In this paper, an expert system was developed using Exsys Corvid software to select suitable biobased polymer materials for packaging fruits, dry food and dairy products. If - Then rule based system was utilized to accomplish the material selection process whereas a score system was formulated to facilitate the ranking of selected materials. The expert system selected materials that satisfied all constraints and selection results were presented in suitability sequence depending on their scores. The expert system selected polylactic acid (PLA) as the most suitable material.

  19. Determining biodegradability of plastic materials under controlled and natural composting environments.

    Science.gov (United States)

    Mohee, R; Unmar, G

    2007-01-01

    With the advent of recently promulgated Government regulations on plastics in Mauritius, a study was initiated to examine the biodegradability of two different types of plastic, namely Willow Ridge Plastics - PDQ-H additive (Plastic A) and Ecosafe Plastic - TDPA additive (Plastic B) under controlled and natural composting environments. The results obtained from the controlled composting environment showed that the cumulative carbon dioxide evolution for Plastic A was much higher than that for Plastic B. Plastic A therefore showed a higher level of biodegradation in terms of CO2 evolution than Plastic B. However, from the regression analysis, it was found that the level of CO2 varying with time fitted the sigmoid type curves with very high correlation coefficients (R2 values: 0.9928, 0.9921 and 0.9816, for reference material, inoculum and Plastic A, respectively). The corresponding F-values obtained from the ANOVA analysis together with significance levels of pbiodegradability experiment were significant. The other experiment was undertaken to observe any physical change of Plastics A and B as compared to a reference plastic, namely, compostable plastic bag (Mater-Bi product-Plastic C), when exposed to a natural composting environment. Thermophilic temperatures were obtained for about 3-5 days of composting and the moisture content was in the range of 60-80% throughout the degradation process. It was observed that after 55 days of composting, Plastic C degraded completely while Plastic A and Plastic B did not undergo any significant degradation. It can be concluded that naturally based plastic made of starch would degrade completely in a time frame of 60 days, whereas plastics with biodegradable additive would require a longer time.

  20. LEVERAGING AGING MATERIALS DATA TO SUPPORT EXTENSION OF TRANSPORTATION SHIPPING PACKAGES SERVICE LIFE

    Energy Technology Data Exchange (ETDEWEB)

    Dunn, K. [Savannah River National Laboratory; Bellamy, S. [Savannah River National Laboratory; Daugherty, W. [Savannah River National Laboratory; Sindelar, R. [Savannah River National Laboratory; Skidmore, E. [Savannah River National Laboratory

    2013-08-18

    Nuclear material inventories are increasingly being transferred to interim storage locations where they may reside for extended periods of time. Use of a shipping package to store nuclear materials after the transfer has become more common for a variety of reasons. Shipping packages are robust and have a qualified pedigree for performance in normal operation and accident conditions but are only certified over an approved transportation window. The continued use of shipping packages to contain nuclear material during interim storage will result in reduced overall costs and reduced exposure to workers. However, the shipping package materials of construction must maintain integrity as specified by the safety basis of the storage facility throughout the storage period, which is typically well beyond the certified transportation window. In many ways, the certification processes required for interim storage of nuclear materials in shipping packages is similar to life extension programs required for dry cask storage systems for commercial nuclear fuels. The storage of spent nuclear fuel in dry cask storage systems is federally-regulated, and over 1500 individual dry casks have been in successful service up to 20 years in the US. The uncertainty in final disposition will likely require extended storage of this fuel well beyond initial license periods and perhaps multiple re-licenses may be needed. Thus, both the shipping packages and the dry cask storage systems require materials integrity assessments and assurance of continued satisfactory materials performance over times not considered in the original evaluation processes. Test programs for the shipping packages have been established to obtain aging data on materials of construction to demonstrate continued system integrity. The collective data may be coupled with similar data for the dry cask storage systems and used to support extending the service life of shipping packages in both transportation and storage.

  1. Application of ISO system to safety test for radioactive material transport package

    Energy Technology Data Exchange (ETDEWEB)

    Seo, K. S.; Lee, J. C.; Bang, K. S. [KAERI, Taejon (Korea, Republic of)

    2003-10-01

    Safety tests for radioactive material transportation package are described in MOST notice 2001-23, IAEA Safety Standards Series No. TS-R-1 and US 10 CFR Part 71. Safety test facilities and equipments were provided to be capable of performing various tests prescribed in those regulations. Test methods and procedures appropriate in International Standard ISO were established and this laboratory of radioactive material transportation package is accredited by Korea Laboratory Accreditation Scheme(KOLAS)

  2. Yield Functions and Plastic Potentials for BCC Metals and Possibly Other Materials

    Energy Technology Data Exchange (ETDEWEB)

    Christensen, R M

    2005-09-29

    Yield functions and plastic potentials are expressed in terms of the invariants of the stress tensor for polycrystalline metals and other isotropic materials. The plastic volume change data of Richmond is used to evaluate the embedded materials properties for some bcc metals and one polymer. A general form for the plastic potential is found that is intended to represent and cover a wide range of materials types.

  3. Pyrolysis of municipal plastic wastes: Influence of raw material composition.

    Science.gov (United States)

    López, A; de Marco, I; Caballero, B M; Laresgoiti, M F; Adrados, A

    2010-04-01

    The objective of this work is the study of pyrolysis as a feedstock recycling process, for valorizing the rejected streams that come from industrial plants, where packing and packaging wastes are classified and separated for their subsequent mechanical recycling. Four real samples collected from an industrial plant at four different times of the year, have been pyrolysed under nitrogen in a 3.5dm(3) autoclave at 500 degrees C for 30min. Pyrolysis liquids are a complex mixture of organic compounds containing valuable chemicals as styrene, ethyl-benzene, toluene, etc. Pyrolysis solids are composed of the inorganic material contained in the raw materials, as well as of some char formed in the pyrolysis process, and pyrolysis gases are mainly composed of hydrocarbons together with some CO and CO(2), and have very high gross calorific values (GCV). It has been proved by the authors that the composition of the raw material (paper, film, and metals contents) plays a significant role in the characteristics of pyrolysis products. High paper content yields water in the pyrolysis liquids, and CO and CO(2) in the gases, high PE film content gives rise to high viscosity liquids, and high metals content yields more aromatics in the liquid products, which may be attributed to the metals catalytic effect.

  4. Hydrothermal carbonization of food waste and associated packaging materials for energy source generation.

    Science.gov (United States)

    Li, Liang; Diederick, Ryan; Flora, Joseph R V; Berge, Nicole D

    2013-11-01

    Hydrothermal carbonization (HTC) is a thermal conversion technique that converts food wastes and associated packaging materials to a valuable, energy-rich resource. Food waste collected from local restaurants was carbonized over time at different temperatures (225, 250 and 275°C) and solids concentrations to determine how process conditions influence carbonization product properties and composition. Experiments were also conducted to determine the influence of packaging material on food waste carbonization. Results indicate the majority of initial carbon remains integrated within the solid-phase at the solids concentrations and reaction temperatures evaluated. Initial solids concentration influences carbon distribution because of increased compound solubilization, while changes in reaction temperature imparted little change on carbon distribution. The presence of packaging materials significantly influences the energy content of the recovered solids. As the proportion of packaging materials increase, the energy content of recovered solids decreases because of the low energetic retention associated with the packaging materials. HTC results in net positive energy balances at all conditions, except at a 5% (dry wt.) solids concentration. Carbonization of food waste and associated packaging materials also results in net positive balances, but energy needs for solids post-processing are significant. Advantages associated with carbonization are not fully realized when only evaluating process energetics. A more detailed life cycle assessment is needed for a more complete comparison of processes. Copyright © 2013 Elsevier Ltd. All rights reserved.

  5. ASSESSMENT OF PLASTIC FLOWS AND STOCKS IN SERBIA USING MATERIAL FLOW ANALYSIS

    Directory of Open Access Journals (Sweden)

    Goran Vujić

    2010-01-01

    Full Text Available Material flow analysis (MFA was used to assess the amounts of plastic materials flows and stocks that are annually produced, consumed, imported, exported, collected, recycled, and disposed in the landfills in Serbia. The analysis revealed that approximatelly 269,000 tons of plastic materials are directly disposed in uncontrolled landfills in Serbia without any preatretment, and that siginificant amounts of these materials have already accumulated in the landfills. The substantial amounts of landfilled plastics represent not only a loss of valuable recourses, but also pose a seriuos treath to the environment and human health, and if the trend of direct plastic landfilling is continued, Serbia will face with grave consecequnces.

  6. Sustainable Materials Management (SMM) Web Academy Webinar: Reducing Wasted Food: How Packaging Can Help

    Science.gov (United States)

    This is a webinar page for the Sustainable Management of Materials (SMM) Web Academy webinar titled Let’s WRAP (Wrap Recycling Action Program): Best Practices to Boost Plastic Film Recycling in Your Community

  7. Excised Abdominoplasty Material as a Systematic Plastic Surgical Training Model

    Directory of Open Access Journals (Sweden)

    M. Erol Demirseren

    2012-01-01

    Full Text Available Achieving a level of technical skill and confidence in surgical operations is the main goal of plastic surgical training. Operating rooms were accepted as the practical teaching venues of the traditional apprenticeship model. However, increased patient population, time, and ethical and legal considerations made preoperation room practical work a must for plastic surgical training. There are several plastic surgical teaching models and simulators which are very useful in preoperation room practical training and the evaluation of plastic surgery residents. The full thickness skin with its vascular network excised in abdominoplasty procedures is an easily obtainable real human tissue which could be used as a training model in plastic surgery.

  8. 49 CFR 173.418 - Authorized packages-pyrophoric Class 7 (radioactive) materials.

    Science.gov (United States)

    2010-10-01

    ... (radioactive) materials. 173.418 Section 173.418 Transportation Other Regulations Relating to Transportation... REGULATIONS SHIPPERS-GENERAL REQUIREMENTS FOR SHIPMENTS AND PACKAGINGS Class 7 (Radioactive) Materials § 173.418 Authorized packages—pyrophoric Class 7 (radioactive) materials. Pyrophoric Class 7...

  9. 49 CFR 175.701 - Separation distance requirements for packages containing Class 7 (radioactive) materials in...

    Science.gov (United States)

    2010-10-01

    ... containing Class 7 (radioactive) materials in passenger-carrying aircraft. 175.701 Section 175.701... packages containing Class 7 (radioactive) materials in passenger-carrying aircraft. (a) The following table... Class 7 (radioactive) materials labeled RADIOACTIVE YELLOW-II or RADIOACTIVE YELLOW-III and...

  10. The industrial metabolism of plastics : analysis of material flows, energy consumption and CO2 emissions in the lifecycle of plastics

    NARCIS (Netherlands)

    Joosten, Ludovicus Antonius Josephus

    2001-01-01

    This thesis deals with the question: Which are promising options for decreasing material consumption, energy consumption and CO2 emissions in the lifecycle of plastics? The research described in this thesis mainly focuses on measures that change the material system, i.e. measures that change the

  11. The industrial metabolism of plastics : analysis of material flows, energy consumption and CO2 emissions in the lifecycle of plastics

    NARCIS (Netherlands)

    Joosten, Ludovicus Antonius Josephus

    2002-01-01

    This thesis deals with the question: Which are promising options for decreasing material consumption, energy consumption and CO2 emissions in the lifecycle of plastics? The research described in this thesis mainly focuses on measures that change the material system, i.e. measures that change the pat

  12. Application of common packaging materials in the probiotic fresh cheese production

    Directory of Open Access Journals (Sweden)

    Mirela Iličić

    2016-03-01

    Full Text Available The aim of this work was to investigate the application of common packaging materials polypropylene (PP and polystyrene (PS in the probiotic fresh cheese production packaging. Probiotic and traditional cheeses were produced from milk with standardized milk fat content of 2.3 g/100 g including the application of two cultures (probiotic and traditional. The samples were packed in the PP and PS cups and stored at 4 ºC for 30 days. The observed permeability of gases through the two applied packaging materials was significantly different. Cheese samples were analysed for microbiological properties whereby lactic acid bacteria, Bifidobacterium sp. and aerobic mesophilic bacteria (AMB were determined. Packaging materials showed no significant effect on the content of ascorbic acid which is known to be sensitive to the presence of oxygen.

  13. Packaging tomorrow : modelling the material input for European packaging in the 21st century

    NARCIS (Netherlands)

    Hekkert, M.P.; Joosten, L.A.J.; Worrell, E.

    2006-01-01

    This report is a result of the MATTER project (MATerials Technology for CO2 Emission Reduction). The project focuses on CO2 emission reductions that are related to the Western European materials system. The total impact of the reduction options for different scenario's will be modeled in MARKAL (MAR

  14. 19 CFR 10.815 - Packaging and packing materials and containers for retail sale and for shipment.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 1 2010-04-01 2010-04-01 false Packaging and packing materials and containers for... RATE, ETC. United States-Bahrain Free Trade Agreement Rules of Origin § 10.815 Packaging and packing... good is packaged for retail sale and packing materials and containers for shipment are to...

  15. 19 CFR 10.775 - Packaging and packing materials and containers for retail sale and for shipment.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 1 2010-04-01 2010-04-01 false Packaging and packing materials and containers for... RATE, ETC. United States-Morocco Free Trade Agreement Rules of Origin § 10.775 Packaging and packing... good is packaged for retail sale and packing materials and containers for shipment are to...

  16. 49 CFR 173.467 - Tests for demonstrating the ability of Type B and fissile materials packagings to withstand...

    Science.gov (United States)

    2010-10-01

    ... Type B and fissile materials packagings to withstand accident conditions in transportation. Each Type B packaging or packaging for fissile material must meet the test requirements prescribed in 10 CFR part 71 for... 49 Transportation 2 2010-10-01 2010-10-01 false Tests for demonstrating the ability of Type B...

  17. Marine fungi: Degraders of poly-3-hydroxyalkanoate based plastic materials

    Directory of Open Access Journals (Sweden)

    Matavulj Milan

    2009-01-01

    Full Text Available The search for new biosynthetic and biodegradable materials to save nonrenewable resources and reduce global pollution problems is an urgent task. Recently, materials like thermoplastic poly-3-hydroxyalkanoates (PHA, have been found synthesized by bacteria as storage materials. The major PHAs synthesized are poly-b-hydroxybutyrate (PHB, poly-b-hydroxyvalerate (PHV and their copolymers. They are already commercially produced and used as BIOPOLTM (ICI, England. Their complete degradability by bacteria has already been shown. Today, oceans and estuaries serve as major landfills, and since fungi are an important part of the degrading microbiota, in order to prove their participation in the degradation process, a simple degradation test suitable for fungi and marine conditions had to be developed. Several solid media based on artificial sea water, differing in the content of non-alkanoate organics and supplemented with 0.1% PHA (or BIOPOLTM as a main source of carbon have been tested. The testing principle consists of clearing the turbid medium in test tube or plates caused by suspended granules of PHA. All media tested supported the growth of fungi. For the discrete and transparent clearing of zones, a mineral medium with 0.01% peptone, 0.01% yeast extract, and 0.1% PHB or BIOPOLTM was finally chosen where the fine and evenly distributed turbidity is accomplished by a specific procedure. This method allows the investigation of degradability of PHA-based plastic materials as well as screening for fungal ability to depolymerise pure PHA homopolymers. Using this medium, 32 strains of marine yeasts and 102 strains of marine mycelial fungi belonging to different systematic and ecological groups were tested for their ability to degrade PHAs. Only about 4% of the strains were able to degrade BIOPOLTM and about 6% depolymerised pure PHB homopolymer. This is in sharp contrast to the results of our previous experiments with 143 strains of terrestrial fungi

  18. Empirical models for end-use properties prediction of LDPE: application in the flexible plastic packaging industry

    Directory of Open Access Journals (Sweden)

    Maria Carolina Burgos Costa

    2008-03-01

    Full Text Available The objective of this work is to develop empirical models to predict end use properties of low density polyethylene (LDPE resins as functions of two intrinsic properties easily measured in the polymers industry. The most important properties for application in the flexible plastic packaging industry were evaluated experimentally for seven commercial polymer grades. Statistical correlation analysis was performed for all variables and used as the basis for proper choice of inputs to each model output. Intrinsic properties selected for resin characterization are fluidity index (FI, which is essentially an indirect measurement of viscosity and weight average molecular weight (MW, and density. In general, models developed are able to reproduce and predict experimental data within experimental accuracy and show that a significant number of end use properties improve as the MW and density increase. Optical properties are mainly determined by the polymer morphology.

  19. Preparation and characterization of polyurethane plasticizer for flexible packaging applications: Natural oils affirmed access

    Directory of Open Access Journals (Sweden)

    Mohammed A. Mekewi

    2017-03-01

    Full Text Available Developing bio-renewable feedstock for polyurethane (PU manufacturing and polymer industry as a whole has become highly desirable for both economic and environmental reasons. In this work castor oil (CO and palm olein (PO polyols were synthesized and partially used as renewable feedstock for the manufacturing of polyurethane plasticizing resin for printing ink applications. The chemical structure of the prepared polyols and polyurethanes were characterized using IR spectra and GPC and their solubility in common solvents was tested. As well, properties such as flexibility, mechanical properties, optical properties, heat seal and freeze resistance of these prepared printing inks were determined. The results indicated that the prepared printing inks from 50% synthesized polyurethane have high thermal stability, adhesion and excellent freeze resistance. The net technical properties of the new ink formulations are relatively comparable to the printing ink prepared from standard polyurethane plasticizer.

  20. Understanding External Plasticization of Melt Extruded PHBV-Wheat Straw Fibers Biodegradable Composites for Food Packaging

    OpenAIRE

    Martino, Lucrezia; Berthet, Marie-Alix; Gontard, Nathalie

    2015-01-01

    The objective of this work is to get further knowledge on the external plasticization mechanisms of melt extruded polyhydroxyl-3-butyrate-co-3-valerate (PHBV) when combined with wheat straw fibers (WSF). Different types of biodegradable substances, all authorized for food contact according to the European regulation, i.e., acetyltributyl citrate (ATBC), glycerol triacetate (GTA) and (PEG) at different molecular weights, were tested at different percentages (5, 10 and 20 wt %). Thermal and mec...

  1. Study on Plastic Coated Overburnt Brick Aggregate as an Alternative Material for Bituminous Road Construction

    OpenAIRE

    Dipankar Sarkar; Manish Pal; Sarkar, Ashoke K.

    2016-01-01

    There are different places in India where natural stone aggregates are not available for constructional work. Plastic coated OBBA can solve the problem of shortage of stone aggregate to some extent. The engineers are always encouraged to use locally available materials. The present investigation is carried out to evaluate the plastic coated OBBA as an alternative material for bituminous road construction. Shredded waste plastics are mixed with OBBA in different percentages as 0.38, 0.42, 0.46...

  2. Fully plastic crack opening analyses of complex-cracked pipes for Ramberg-Osgood materials

    Energy Technology Data Exchange (ETDEWEB)

    Jeong, Jae Uk; Choi, Jae Boong [Sungkyunkwan University, Suwon (Korea, Republic of); Huh, Nam Su [Seoul National University, Seoul (Korea, Republic of); Kim, Yun Jae [Korea University, Seoul (Korea, Republic of)

    2016-04-15

    The plastic influence functions for calculating fully plastic Crack opening displacement (COD) of complex-cracked pipes were newly proposed based on systematic 3-dimensional (3-D) elastic-plastic Finite element (FE) analyses using Ramberg-Osgood (R-O) relation, where global bending moment, axial tension and internal pressure are considered separately as a loading condition. Then, crack opening analyses were performed based on GE/EPRI concept by using the new plastic influence functions for complex-cracked pipes made of SA376 TP304 stainless steel, and the predicted CODs were compared with FE results based on deformation plasticity theory of tensile material behavior. From the comparison, the confidence of the proposed fully plastic crack opening solutions for complex-cracked pipes was gained. Therefore, the proposed engineering scheme for COD estimation using the new plastic influence functions can be utilized to estimate leak rate of a complex-cracked pipe for R-O material.

  3. New absorbent acoustic materials from plastic bottle remnants

    Directory of Open Access Journals (Sweden)

    del Rey, R.

    2011-12-01

    Full Text Available In the building acoustics field usually fibrous materials are used as sound absorbing materials. Nowadays polyester fiber is one of the most used but the pure chip of polyester has a problem. Polyester is obtained of petroleum and its price was increasing last years. This paper, presents an alternative polyester wool which obtained by PET treatment (recycle of plastic bottle’s. Absorption coefficient values at normal incidence measured in reverberation chamber were compared (new wool obtained by PET method and materials obtained from pure chip of polyester.Furthermore, this paper propound a empiric model that describe the acoustic performance of this new wool. The results have been good. The pure fiber has been replaced by recycle fiber in its manufacture process.

    En el ámbito de acústica de la edificación es común el uso de materiales fibrosos como materiales absorbentes acústicos. Uno de estos materiales cada vez más utilizado es la lana de poliéster. Un problema que presenta el chip virgen de poliéster es que se obtiene del petróleo, cuyo precio no hace más que incrementarse en los últimos años. En este trabajo se presenta una lana de poliéster alternativa, obtenida mediante el tratamiento del PET, a través del conveniente ciclo de reciclado de botellas de plástico. Se comparan valores del coeficiente de absorción; en incidencia normal y en cámara reverberante de los materiales elaborados a partir de chip virgen y de las nuevas lanas obtenidas del PET. Además, se propone un modelo empírico de comportamiento acústico de estas nuevas lanas. Los resultados obtenidos han sido favorables, la fibra virgen ya ha sido sustituida por fibra reciclada en su proceso de fabricación.

  4. Substitution potentials of recycled HDPE and wood particles from post-consumer packaging waste in Wood-Plastic Composites.

    Science.gov (United States)

    Sommerhuber, Philipp F; Welling, Johannes; Krause, Andreas

    2015-12-01

    The market share of Wood-Plastic Composites (WPC) is small but expected to grow sharply in Europe. This raises some concerns about suitable wood particles needed in the wood-based panels industry in Europe. Concerns are stimulated by the competition between the promotion of wooden products through the European Bioeconomy Strategy and wood as an energy carrier through the Renewable Energy Directive. Cascade use of resources and valorisation of waste are potential strategies to overcome resource scarcity. Under experimental design conditions, WPC made from post-consumer recycled wood and plastic (HDPE) were compared to WPC made from virgin resources. Wood content in the polymer matrix was raised in two steps from 0% to 30% and 60%. Mechanical and physical properties and colour differences were characterized. The feasibility of using cascaded resources for WPC is discussed. Results indicate the technical and economic feasibility of using recycled HDPE from packaging waste for WPC. Based on technical properties, 30% recycled wood content for WPC is feasible, but economic and political barriers of efficient cascading of biomass need to be overcome.

  5. The occurrence of extractible ink residuals in packaging materials used in the Czech Republic.

    OpenAIRE

    Dupáková, Zdeňka; Dobiáš, Jaroslav; Votavová, Lenka; Klaudisová, Kamila; Voldřich, Michal

    2009-01-01

    Abstract The residuals of printing ink components were determined in 94 samples of packaging materials commercially used in the Czech Republic for food packaging. Tested samples included printed polyethylene and polypropylene films, coextruded and laminated films, paperboard beverages boxes, foils for thermo sealing of polystyrene cups and polypropylene cups. Printing ink components were extracted with diethylether, then separated and determined using gas chromatography coupled wit...

  6. Food safety concerns deriving from the use of silver based food packaging materials: a case study.

    Directory of Open Access Journals (Sweden)

    Alessandra ePezzuto

    2015-10-01

    Full Text Available The formulation of innovative packaging solutions, exerting a functional antimicrobial role in slowing down food spoilage, is expected to have a significant impact on the food industry, allowing both the maintenance of food safety criteria for longer periods and the reduction of food waste. Different materials are considered able to exert the required antimicrobial activity, among which are materials containing silver. However, challenges exist in the application of silver to food contact materials due to knowledge gaps in the production of ingredients, stability of delivery systems in food matrices and health risks caused by the same properties which also offer the benefits. Aims of the present study were to test the effectiveness and suitability of two packaging systems, one of which contained silver, for packaging and storing Stracchino cheese, a typical Italian fresh cheese, and to investigate if there was any potential for consumers to be exposed to silver, via migration from the packaging to the cheese. Results did not show any significant difference in the effectiveness of the packaging systems on packaged Stracchino cheese, excluding that the active packaging systems exerted an inhibitory effect on the growth of spoilage microorganisms. Moreover, silver migrated into the cheese matrix throughout the storage time (24 days. Silver levels in cheese finally exceeded the maximum established level for the migration of a non-authorised substance through a functional barrier (Commission Regulation (EC No. 450/2009. This result poses safety concerns and strongly suggests the need for more research aimed at better characterizing the new packaging materials in terms of their potential impacts on human health and the environment.

  7. Food safety concerns deriving from the use of silver based food packaging materials.

    Science.gov (United States)

    Pezzuto, Alessandra; Losasso, Carmen; Mancin, Marzia; Gallocchio, Federica; Piovesana, Alessia; Binato, Giovanni; Gallina, Albino; Marangon, Alberto; Mioni, Renzo; Favretti, Michela; Ricci, Antonia

    2015-01-01

    The formulation of innovative packaging solutions, exerting a functional antimicrobial role in slowing down food spoilage, is expected to have a significant impact on the food industry, allowing both the maintenance of food safety criteria for longer periods and the reduction of food waste. Different materials are considered able to exert the required antimicrobial activity, among which are materials containing silver. However, challenges exist in the application of silver to food contact materials due to knowledge gaps in the production of ingredients, stability of delivery systems in food matrices and health risks caused by the same properties which also offer the benefits. Aims of the present study were to test the effectiveness and suitability of two packaging systems, one of which contained silver, for packaging and storing Stracchino cheese, a typical Italian fresh cheese, and to investigate if there was any potential for consumers to be exposed to silver, via migration from the packaging to the cheese. Results did not show any significant difference in the effectiveness of the packaging systems on packaged Stracchino cheese, excluding that the active packaging systems exerted an inhibitory effect on the growth of spoilage microorganisms. Moreover, silver migrated into the cheese matrix throughout the storage time (24 days). Silver levels in cheese finally exceeded the maximum established level for the migration of a non-authorised substance through a functional barrier (Commission of the European Communities, 2009). This result poses safety concerns and strongly suggests the need for more research aimed at better characterizing the new packaging materials in terms of their potential impacts on human health and the environment.

  8. Assessing microbiologically induced corrosion of waste package materials in the Yucca Mountain repository

    Energy Technology Data Exchange (ETDEWEB)

    Horn, J. M., LLNL

    1998-01-01

    The contribution of bacterial activities to corrosion of nuclear waste package materials must be determined to predict the adequacy of containment for a potential nuclear waste repository at Yucca Mountain (YM), NV. The program to evaluate potential microbially induced corrosion (MIC) of candidate waste container materials includes characterization of bacteria in the post-construction YM environment, determination of their required growth conditions and growth rates, quantitative assessment of the biochemical contribution to metal corrosion, and evaluation of overall MIC rates on candidate waste package materials.

  9. Reciclagem de embalagens plásticas flexíveis: contribuição da identificação correta Flexible plastic packaging recycling: the contribution of the correct identification

    Directory of Open Access Journals (Sweden)

    Leda Coltro

    2013-01-01

    , folha de alumínio, é proposta a inclusão da identificação destes materiais na embalagem.Packages have high rotation as they become municipal solid waste just after the consumption of the product. Therefore, packages should be labeled with identification of the material they are made of in order to help the recycling chain. Many products made from plastics show a resin identification code - usually from 1 to 7 inside a three-arrow triangle above a monogram - aimed at identifying the type of plastic the product is made of, and help its separation and later recycling. In other words, one aims to facilitate recovery of plastics discarded with the municipal solid waste. In this study we collected data on the resin identification code in flexible plastic packages to assess whether the guidelines for material identification are being followed. The data collection was performed in a total of 509 flexible plastic packages used for packing food and non-food products available in the Brazilian market. Even though the NBR 13230 Brazilian standard is already in its second revision, the resin identification code in plastic packages is still used in a very heterogeneous fashion. Approximately 50% of the packages had the resin identification code. Up to 30% of some packages showed incorrect material identification code. Therefore, misinformation still occurs in the Brazilian market concerning the type of material for plastic packaging - including lack of the resin identification code and incorrect form of identification code in the plastic packaging. Both of these problems have negative effects on the plastic recycling chain. We propose that other materials used in flexible plastic packages, e.g. aluminum foil, should also be identified, in order to make the separation and recycling easier.

  10. Characterization of Elastic-plastic Material Properties for IMC Layer of ENEPIG by Using Reverse Algorithm

    Science.gov (United States)

    Kim, Jong-Min; Lee, Hyun-Boo; Chang, Yoon-Suk; Choi, Jae-Boong; Kim, Young-Jin; Ji, Kum-Young

    2010-05-01

    Recently, the reliability assurance of lead-free solder to prevent environmental contamination is quite important issue for chip-scale packaging. Although lots of efforts have been devoted to the solder undergone drop, shear and creep loads, there was a little research on IMC due primarily to its thickness restriction and geometric irregularity. However, the IMC is known as the weakest layer governing failures of the solder joint. The present work is to characterize realistic material properties of the IMC for ENEPIG process. Lee's modified reverse algorithm was adopted to determine elastic-plastic stress-strain curve and so forth, after examining several methods, which requires inherently elastic data. In this context, a series of nano-indentation tests as well as corresponding simulations were carried out by changing indentation depths from 200 to 400 nm and strain rates from 0.05 to 0.10 1/s. It would be conclude that effect of strain rate is relatively small and IMC layer should be more than 5 times of indentation depth when using the recommended method, which are applicable to generate realistic material properties for further diverse structural integrity simulations.

  11. Numerical Simulation of the Mechanical Properties and Failure of Heterogeneous Elasto-Plastic Materials

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    A general numerical approach was developed to simulate the mechanical properties and the failure of heterogeneous elasto-plastic materials using statistical distributions of the material properties. An appropriate elastic-plastic constitutive relation is used to describe the material behavior and failure in each element, with a two-parameter Weibull distribution used to produce the initial heterogeneous material property variations. An adaptive incremental load-step is applied so that only one or a few elements (or integration points) change their status (i.e., from elastic to plastic, or from plastic to strain failure) within one load step. A failed element is then assigned a very small modulus to simulate the failure rather than removing it from the model, which keeps the continuity of the geometric mesh. The numerical results show that the model is suitable for simulating the effective mechanical properties and failure of heterogeneous materials with local elasto-plastic constitutive relations.

  12. Crystallinity in starch plastics: consequences for material properties

    NARCIS (Netherlands)

    Vliegenthart, J.F.G.; Soest, J.J.G. van

    1997-01-01

    The processing of starches with biodegradable additives has made biodegradable plastics suitable for a number of applications. Starch plastics are partially crystalline as a result of residual crystallinity and the recrystallization of amylose and amylopectin. Such crystallinity is a key determinant

  13. Evaluation of chemical elements migration from food packaging plastics into food; Avaliacao da migracao de elementos quimicos das embalagens plasticas para alimentos

    Energy Technology Data Exchange (ETDEWEB)

    Kamiya, Adriana M.; Fulfaro, Roberto; Saiki, Mitiko [Instituto de Pesquisas Energeticas e Nucleares (IPEN), Sao Paulo, SP (Brazil). Supervisao de Radioquimica

    2000-07-01

    This work presents results of As, Cd, Co, Cr, Sb, Se, Sn, and Zn obtained in the analysis of plastics from food packing materials by instrumental neutron activation analysis. The radiometric method was also applied to evaluate the migration of Co and Sb from the plastic into the food simulant. The possible sources of the toxic elements in plastic materials and the advantages of radiometric method in the migration evaluation are discussed. (author)

  14. Tracer aroma compound transfer from a solid and complex-flavored food matrix packed in treated papers or plastic packaging film.

    Science.gov (United States)

    Dury-Brun, Cécile; Lequin, Sonia; Chalier, Pascale; Desobry, Stéphane; Voilley, Andrée

    2007-02-21

    The objective of this work was to study the transfer of four aroma compounds (ethyl butyrate, ethyl hexanoate, cis-3-hexenol, and benzaldehyde) from a solid and complex-flavored food matrix (sponge cake) toward and through packaging films placed in indirect contact during storage in accelerated aging conditions (38 degrees C and 86% relative humidity gradient). The efficiency of treated papers relative to that of standard paper and plastic as barrier was tested. Before storage, aroma compound volatility in the sponge cake was measured, and similar values were found between aroma compounds, due to the fat content of the sponge cake. Whatever the aroma compound, permeability values during storage were similar for the same packaging film. The plastic film was the highest barrier, whereas calendering and coating treatments applied to treated papers decreased effectively their permeability. An opposite trend was observed for aroma compound sorption into packaging films during storage.

  15. 21 CFR 181.22 - Certain substances employed in the manufacture of food-packaging materials.

    Science.gov (United States)

    2010-04-01

    ... of food-packaging materials. Prior to the enactment of the food additives amendment to the Federal... materials. So used, these substances are not considered “food additives” within the meaning of section 201(s... intended to accomplish any physical or technical effect in the food itself, shall be reduced to the...

  16. Final versions of the initial package of classroom materials and guidelines

    NARCIS (Netherlands)

    Doorman, Michiel; Jonker, Vincent

    2014-01-01

    The main aim of the mascil Work Package 3 ‘classroom materials’ is to present guidelines and an online collection of teaching materials that encourage and support teachers to design their own classroom materials that connect IBL and the WoW in mathematics and science education.The collection present

  17. Impact of Chlorine dioxide Gas on the Barrier Properties of Polymeric Packaging Materials

    Science.gov (United States)

    One important criterion of polymeric material selection and packaging design for fresh produce is choosing the material with suitable ratio of carbon dioxide and oxygen permabilities (PCO2/P O2), to the respiratory proportion of the targeted produce. The ratio of [O2] and [CO2] in the head space var...

  18. Certified reference materials for food packaging specific migration tests: development, validation and modelling

    NARCIS (Netherlands)

    Stoffers, N.H.

    2005-01-01

    Keywords:certified reference materials; diffusion; food contact materials; food packaging; laurolactam; migration modelling; nylon; specific migration This thesis compiles several research topics

  19. 49 CFR 173.421 - Excepted packages for limited quantities of Class 7 (radioactive) materials.

    Science.gov (United States)

    2010-10-01

    ... exceed 0.005 mSv/hour (0.5 mrem/ hour); (3) The nonfixed (removable) radioactive surface contamination on... 7 (radioactive) materials. 173.421 Section 173.421 Transportation Other Regulations Relating to... MATERIALS REGULATIONS SHIPPERS-GENERAL REQUIREMENTS FOR SHIPMENTS AND PACKAGINGS Class 7 (Radioactive...

  20. Performance of Nonmigratory Iron Chelating Active Packaging Materials in Viscous Model Food Systems.

    Science.gov (United States)

    Roman, Maxine J; Decker, Eric A; Goddard, Julie M

    2015-09-01

    Many packaged food products undergo quality deterioration due to iron promoted oxidative reactions. Recently, we have developed a nonmigratory iron chelating active packaging material that represents a novel approach to inhibit oxidation of foods while addressing consumer demands for "cleanˮ labels. A challenge to the field of nonmigratory active packaging is ensuring that surface-immobilized active agents retain activity in a true food system despite diffusional limitations. Yet, the relationship between food viscosity and nonmigratory active packaging activity retention has never been characterized. The objective of this study was to investigate the influence of food viscosity on iron chelation by a nonmigratory iron chelating active packaging material. Methyl cellulose was added to aqueous buffered iron solutions to yield model systems with viscosities ranging from ∼1 to ∼10(5)  mPa·s, representing viscosities ranging from beverage to mayonnaise. Iron chelation was quantified by material-bound iron content using colorimetry and inductively coupled plasma-optical emission spectrometry (ICP-OES).  Maximum iron chelation was reached in solutions up to viscosity ∼10(2)  mPa·s. In more viscous solutions (up to ∼10(4)  mPa·s), there was a significant decrease in iron chelating capacity (P influence of different food hydrocolloids on the performance of nonmigratory iron chelating active packaging was characterized. Methyl cellulose and carrageenan did not compete with the material for specific iron chelation (P > 0.05). Materials retained 32% to 45% chelating capacity when in contact with competitively chelating hydrocolloids guar gum, locust bean gum, and xanthan gum. This work demonstrates the potential application of nonmigratory iron chelating active packaging in liquid and semi-liquid foods to allow for the removal of synthetic chelators, while maintaining food quality.

  1. Perceptions of Sustainability and Functional Aspects on Liquid Carton Board Packaging Materials versus Competing Materials for Juice Applications in Sweden

    Directory of Open Access Journals (Sweden)

    Carl Olsmats

    2015-08-01

    Full Text Available This research explores the downstream perceptions of liquid carton board versus competing materials in packaging applications for juice. The methodology used is focus groups. The context is sustainability and functional performance, and related potential implications for the beverage industry value chain. The purpose is to get a deeper insight and understanding of functionality in relation to juice beverage packaging. The results confirm that there is no optimal packaging for every juice product, but a multitude, depending on the distribution channel, retail outlet, customer preferences, and context of consumption. There are some general packaging preferences, but the main deciding criteria for purchase seem to be the product characteristics in terms of quality, taste, brand, price and shelf life. For marketing reasons, packaging has to be adopted to the product and its positioning, liquid carton board packaging seem to have some functional advantages in distribution and is considered as sustainable and functional among many consumers. Major drawbacks seem to be shape limitations, lack of transparency, and lack of a “premium look”. To improve packaging performance and avoid sub-optimization, actors in the beverage industry value chain need to be integrated in development processes.

  2. Aluminum-Scandium: A Material for Semiconductor Packaging

    Science.gov (United States)

    Geissler, Ute; Thomas, Sven; Schneider-Ramelow, Martin; Mukhopadhyay, Biswajit; Lang, Klaus-Dieter

    2016-10-01

    A well-known aluminum-scandium (Al-Sc) alloy, already used in lightweight sports equipment, is about to be established for use in electronic packaging. One application for Al-Sc alloy is manufacture of bonding wires. The special feature of the alloy is its ability to harden by precipitation. The new bonding wires with electrical conductivity similar to pure Al wires can be processed on common wire bonders for aluminum wedge/wedge (w/w) bonding. The wires exhibit very fine-grained microstructure. Small Al3Sc particles are the main reason for its high strength and prevent recrystallization and grain growth at higher temperatures (>150°C). After the wire-bonding process, the interface is well closed. Reliability investigations by active power cycling demonstrated considerably improved lifetime compared with pure Al heavy wires. Furthermore, the Al-Sc alloy was sputter-deposited onto silicon wafer to test it as chip metallization in copper (Cu) ball/wedge bonding technology. After deposition, the layers exhibited fine-grained columnar structure and small coherent Al3Sc particles with dimensions of a few nanometers. These particles inhibit softening processes such as Al splashing in fine wire bonding processes and increase the thickness of remnant Al under the copper balls to 85% of the initial thickness.

  3. Flexible Foam Protection Materials for Constellation Space Suit Element Portable Life Support Subsystem Packaging Study

    Science.gov (United States)

    Tang, Henry H.; Orndoff, Evelyne S.; Thomas, Gretchen A.

    2009-01-01

    This paper discusses the effort in evaluating and selecting a light weight impact protection material for the Constellation Space Suit Element (CSSE) Portable Life Support Subsystem (PLSS) conceptual packaging study. A light weight material capable of holding and protecting the components inside the PLSS is required to demonstrate the viability of the flexible PLSS packaging concept. The material needs to distribute, dissipate, and absorb the impact energy of the PLSS falling on the lunar surface. It must also be very robust and function in the extreme lunar thermal vacuum environment for up to one hundred Extravehicular Activity (EVA) missions. This paper documents the performance requirements for selecting a foam protection material, and the methodologies for evaluating commercial off-the-shelf (COTS) foam protection materials. It also presents the materials properties test results and impact drop test results of the various foam materials evaluated in the study. The findings from this study suggest that a foam based flexible protection system is a viable solution for PLSS packaging. However, additional works are needed to optimize COTS foam properties or to develop a composite foam system that will meet all the performance requirements for the CSSE PLSS flexible packaging.

  4. 生物质缓冲包装材料制备及性能实验研究%Preparation and properties of biomass cushion packaging material

    Institute of Scientific and Technical Information of China (English)

    李刚; 李方义; 管凯凯; 刘鹏; 吕禹; 贾秀杰; 李剑峰

    2013-01-01

    To solve the environmental pollution caused by the non-degradable waste of plastic packaging materials,the biomass cushion packaging materials with different ingredients have been synthesized,which are made up of straw fiber and starch as the main raw materials.The orthogonal experiment method is used to study the impact of the mass ratio of fiber and starch,the content of plasticizer,active agent and blowing agent on the compressive strength of biomass cushion packaging material.The results were as follows:the influence order of various factors on compressive strength was:plasticizer >the mass ratio of fiber and starch> foaming agent>active agent.When the contents of the plasticizer,foaming agent,active agent are respectively 12%,0.1%,0.3% with the mass ratio of fiber and starch being 2:5,the compressive strength can reach 0.94MPa.Through research on the impacts of plasticizer content and mass ratio of fiber and starch on the cushion performance,the cushion coefficient of the material decreases firstly and increases subsequently with the two factors rising.When the plasticizer content was 12% and the mass ratio of fiber and starch was 2:5,the smallest cushion coefficient and the best cushion performance of the material are obtained.Compared the cushion and rebound performance with EPS (expanded polystyrene),EPE (expanded polyethylene) and other packaging materials,it indicates that the biomass cushion packaging material can replace the cushion packaging materials such as EPS and EPE.%为解决不可降解的废弃塑料类包装材料对环境造成的污染,以稻草纤维、淀粉为主要原料制备了生物质缓冲包装材料,采用正交实验方法研究了生物质缓冲包装材料纤维与淀粉质量比、塑化剂、活性剂和发泡剂含量等对材料抗压强度的影响,结果表明,各因素对材料抗压强度影响的主次顺序为塑化剂>纤维与淀粉质量比>发泡剂>活性剂.塑化剂含量为12%、

  5. MATEO: a software package for the molecular design of energetic materials.

    Science.gov (United States)

    Mathieu, Didier

    2010-04-15

    To satisfy the need of energetic materials chemists for reliable and efficient predictive tools in order to select the most promising candidates for synthesis, a custom software package is developed. Making extensive use of publicly available software, it integrates a wide range of models and can be used for a variety of tasks, from the calculation of molecular properties to the prediction of the performance of heterogeneous materials, such as propellant compositions based on ammonium perchlorate/aluminium mixtures. The package is very easy to use through a graphical desktop environment. According to the material provided as input, suitable models and parameters are automatically selected. Therefore, chemists can apply advanced predictive models without having to learn how to use complex computer codes. To make the package more versatile, a command-line interface is also provided. It facilitates the assessment of various procedures by model developers.

  6. An Investigation Into The Viability Of Nanocrystalline Cellulose As A Packaging Material

    Science.gov (United States)

    Glass, John

    The focus of this proposal is to identify unexplored areas of research in the field of packaging science, specifically related to the incorporation of Nanocrystalline Cellulose (NCC) as a functional material in fiber based packaging, as well as to highlight some of potential risks and unknowns in the product lifecycle. This research hypothesizes that incorporating NCC into wood fiber-based c-flute corrugated packaging medium will show a sufficient performance improvement to justify additional research. Nanomaterials, as a whole, are still being understood, including those using naturally occurring bases such as NCC. Further incremental testing with NCC will help provide a performance and safety baseline for the necessary future research prior to mass production. NCC holds great promise for the future: a commonly available, naturally occurring material that's easily recyclable and biodegradable, yet has the strength of steel. Due diligence is required for this material to come to market in a safe and sustainable manner.

  7. Antioxidant BHT Modelling Migration from Food Packaging of High Density Polyethylene Plastics into the Food Simulant

    Directory of Open Access Journals (Sweden)

    Chi Haitao

    2015-09-01

    Full Text Available Made of High Density Polyethylene (HDPE films containing antioxidant 2, 6-di-tert-butyl-p-cresol (BHT, film samples were manufactured by plastic extrusion equipment, 95% ethanol aqueous solution simulating liquid was used for stimulant, using High Performance Liquid Chromatography (HPLC for the long-term migration test of 4 kinds of HDPE films containing different concentrations of antioxidant BHT. The migration data were processed by using Weibull model and then the migration model was specific under experimental conditions. Migration model was setup using the migrating data by Weibull model to fitting real experimental data. Using empirical formula reported FDA model formula and the diffusion coefficient constant D, calculated by the FDA model. Two kinds of model numerical after compared according to FDA model transfer numerical literature that is far lower than the actual test migration value. According to the actual test migration value, Weibull model numerical and experimental tests that the migration software fitting values are consistent.

  8. 9975 SHIPPING PACKAGE PERFORMANCE OF ALTERNATE MATERIALS FOR LONG-TERM STORAGE APPLICATION

    Energy Technology Data Exchange (ETDEWEB)

    Skidmore, E.; Hoffman, E.; Daugherty, W.

    2010-02-24

    The Model 9975 shipping package specifies the materials of construction for its various components. With the loss of availability of material for two components (cane fiberboard overpack and Viton{reg_sign} GLT O-rings), alternate materials of construction were identified and approved for use for transport (softwood fiberboard and Viton{reg_sign} GLT-S O-rings). As these shipping packages are part of a long-term storage configuration at the Savannah River Site, additional testing is in progress to verify satisfactory long-term performance of the alternate materials under storage conditions. The test results to date can be compared to comparable results on the original materials of construction to draw preliminary conclusions on the performance of the replacement materials.

  9. Flexible Foam Protection Materials for Portable Life Support System Packaging Study

    Science.gov (United States)

    Tang,Henry H.; Dillon, Paul A.; Thomas, Gretchen A.

    2009-01-01

    This paper discusses the phase I effort in evaluating and selecting a light weight impact protection material for the Constellation Space Suit Element (CSSE) Portable Life Support System (PLSS) conceptual packaging study. A light weight material capable of holding and protecting the components inside the PLSS is required to demonstrate the viability of the flexible PLSS packaging concept. The material needs to distribute, dissipate, and absorb the impact energy of the PLSS falling on the lunar surface. It must also be robust to consistently perform over several Extravehicular Activity (EVA) missions in the extreme lunar thermal vacuum environment. This paper documents the performance requirements for selecting a foam protection material, and the methodologies for evaluating some commercial off-the-shelf (COTS) foam material candidates. It also presents the mechanical properties and impact drop tests results of the foam material candidates. The results of this study suggest that a foam based flexible protection system is a viable solution for PLSS packaging. However, additional works are needed to optimize COTS foam or to develop a composite foam system that will meet all the performance requirements for the CSSE PLSS flexible packaging.

  10. THE TYPE OF PACKAGING MATERIAL AND STORAGE CONDITIONS AS FACTORS FOR WHEAT SEED QUALITY

    OpenAIRE

    Josip Šimenić

    2000-01-01

    Seed of cereal is normally grown on 5-8% of the overall plots under cereals in the Republic of Croatia. The produced seed meets the needs for high quality seed of wheat, barley, oat and other cereals. Certain quantities of seed remain unsold every year and are kept at various storage conditions and in various packaging material. The objective of this paper was to find out which storage conditions and what sort of packaging material would provide for the best viability of wheat see...

  11. Materials Assessment of Insulating Foam in the 9977 Shipping Package for Long-Term Storage - Annual Report

    Energy Technology Data Exchange (ETDEWEB)

    McWilliams, A. J. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2016-08-01

    The 9977 shipping package is being evaluated for long-term storage applications in the K-Area Complex (KAC) with specific focus on the packaging foam material. A rigid closed cell polyurethane foam, LAST-A-FOAM® FR-3716, produced by General Plastics Manufacturing Company is sprayed and expands to fill the void between the inner container and the outer shell of the package. The foam is sealed in this annular space and is not accessible. During shipping and storage, the foam experiences higher than ambient temperatures from the heat generated by nuclear material within the package creating the potential for degradation of the foam. A series of experiments is underway to determine the extent of foam degradation. Foam samples of three densities have been aging at elevated temperatures 160 °F, 160 °F + 50% relative humidity (RH), 185 °F, 215 °F, and 250 °F since 2014. Samples were periodically removed and tested. After approximately 80 weeks, samples conditioned at 160 °F, 160 °F + 50% RH, and 185 °F have retained initial property values while samples conditioned at 215 °F have reduced intumescence. Samples conditioned at 250 °F have shown the most degradation, loss of volume, mass, absorbed energy under compression, intumescence, and increased flammability. Based on the initial data, temperatures up to 185 °F have not yet shown an adverse effect on the foam properties and it is recommended that exposure of FR-3716 foam to temperatures in excess of 250 °F be avoided or minimized. Testing will continue beyond the 96 week mark. This will provide additional data to help define the long-term behavior for the lower temperature conditions. Additional testing will be pursued in an attempt to identify transition points (threshold times and temperatures) at the higher temperatures of interest, as well as possible benefits of aging within the relatively oxygen-free environment the foam experiences inside the 9977 shipping package.

  12. Characteristics of materials and thermal treatments applied to gearwheels obtained by plastic deformation

    Science.gov (United States)

    Bostan, I.; Dulgheru, V.; Trifan, N.

    2016-08-01

    A variety of materials are used in the manufacture of gearwheels. These materials satisfy various working conditions for gears. Such gears are made of metallic materials - ferrous, non-ferrous and from plastic materials. Among ferrous materials the following are used: irons; cast, forged and rolled steels; among non-ferrous materials the following are used: bronze, aluminium alloys, brass, etc., and of plastics the following are used: textolite, polyamide, polyacetal. In the practice of exploitation and in the process of special research it was established that the permissible load, according to teeth contact resistance, is generally determined by the hardness of the material. The highest hardness and respectively, the smallest sizes and reduced mass of the transmission can be obtained in the manufacture of steel gears via thermal treatment. It is obvious that by plastic deformation at cold it cannot be obtained gearwheels with complicated configuration as deformed plastic metal will form cracks caused by low plasticity. To improve processability by plastic deformation the mouldings for gearwheels are heated. With increasing the heating temperature, plasticity increases and resistance to deformation decreases.

  13. 49 CFR 175.702 - Separation distance requirements for packages containing Class 7 (radioactive) materials in cargo...

    Science.gov (United States)

    2010-10-01

    ... containing Class 7 (radioactive) materials in cargo aircraft. 175.702 Section 175.702 Transportation Other... (radioactive) materials in cargo aircraft. (a) No person may carry in a cargo aircraft any package required by... separation distance between the surfaces of the radioactive materials packages, overpacks or...

  14. 49 CFR 175.706 - Separation distances for undeveloped film from packages containing Class 7 (radioactive) materials.

    Science.gov (United States)

    2010-10-01

    ... packages containing Class 7 (radioactive) materials. 175.706 Section 175.706 Transportation Other Regulations Relating to Transportation PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF... (radioactive) materials. No person may carry in an aircraft any package of Class 7 (radioactive)...

  15. Processing and Validation of Whey-Protein-Coated Films and Laminates at Semi-Industrial Scale as Novel Recyclable Food Packaging Materials with Excellent Barrier Properties

    Directory of Open Access Journals (Sweden)

    E. Bugnicourt

    2013-01-01

    Full Text Available A biopolymer coating for plastic films was formulated based on whey protein, and its potential to replace current synthetic oxygen barrier layers used in food packaging such as ethylene vinyl alcohol copolymers (EVOH was tested. The whey-coating application was performed at semi-industrial scale. High barrier to oxygen with transmission rate down to ranges of 1 cm3 (STP m−2 d−1 bar−1 at and 50% relative humidity (r.h. but interesting humidity barrier down to ranges of 3 g m−2 d−1 (both normalized to 100 μm thickness were reached, outperforming most existing biopolymers. Coated films were validated for storing various food products showing that the shelf life and sensory attributes were maintained similar to reference packaging films while complying with food safety regulations. The developed whey coating could be enzymatically removed within 2 hours and is therefore compatible with plastic recycling operations to allow multilayer films to become recyclable by separating the other combined layers. A life cycle assessment was performed showing a significant reduction in the environmental impact of the packaging thanks in particular to the possibility of recycling materials as opposed to incinerating those containing EVOH or polyamide (PA, but due to the use of biosourced raw materials.

  16. MIXPAC: a subroutine package for calculating equations of state for equilibrium mixtures of materials

    Energy Technology Data Exchange (ETDEWEB)

    Cranfill, C.W.

    1983-08-01

    This manual describes MIXPAC, a subroutine package for calculating equations of state (i.e., thermodynamic and transport properties) for plasmas composed of equilibrium mixtures of materials. The package is vectorized for the Los Alamos Cray-1 computers and uses EOSPAC, another vectorized subroutine package, to access the Los Alamos Sesame EOS data library. Each mixture is forced to be in equilibrium through the constraints that all its constituents have the same values for two state functions (e.g., temperature and pressure). The desired equations of state (including first partial derivatives) are then calculated for the mixture consistent with these constraints. All equations of state available for pure materials through EOSPAC are available for equilibrium mixtures through MIXPAC.

  17. The challenge of identifying non-intentionally added substances from food packaging materials: a review.

    Science.gov (United States)

    Nerin, C; Alfaro, P; Aznar, M; Domeño, C

    2013-05-01

    Packaged food can contain non-intentionally added substances (NIAS) as a result of reaction and degradation processes or the presence of impurities in the raw materials used for the packaging production. This manuscript reviews the evidence of NIAS and their possible origin. One of the most challenging and difficult tasks when a sample of packaging materials arrives at the laboratory is knowing the procedure to apply for identifying the unknown compounds. This work proposes an analytical procedure for sample treatment, applicable to polymers as well as to migration samples, and for NIAS identification. The identification protocol comprises the determination of both volatile and non-volatile compounds. A review is presented of the most novel analytical techniques used for identification purposes, particularly high resolution mass spectrometry (HRMS).

  18. Phase Change Materials for Thermal Management of IC Packages

    Directory of Open Access Journals (Sweden)

    P. Fiala

    2007-06-01

    Full Text Available This paper deals with the application of phase change materials (PCM for thermal management of integrated circuits as a viable alternative to active forced convection cooling systems. The paper presents an analytical description and solution of heat transfer, melting and freezing process in 1D which is applied to inorganic crystalline salts. There are also results of numerical simulation of a real 3D model. These results were obtained by means of the finite element method (FEM. Results of 3D numerical solutions were verified experimentally.

  19. Stress Wave Propagation in Viscoelastic-Plastic Rock-Like Materials

    Directory of Open Access Journals (Sweden)

    Liu Lang

    2016-05-01

    Full Text Available Rock-like materials are composites that can be regarded as a mixture composed of elastic, plastic, and viscous components. They exhibit viscoelastic-plastic behavior under a high-strain-rate loading according to element model theory. This paper presents an analytical solution for stress wave propagation in viscoelastic-plastic rock-like materials under a high-strain-rate loading and verifies the solution through an experimental test. A constitutive equation of viscoelastic-plastic rock-like materials was first established, and then kinematic and kinetic equations were then solved to derive the analytic solution for stress wave propagation in viscoelastic-plastic rock-like materials. An experimental test using the SHPB (Split Hopkinson Pressure Bar for a concrete specimen was conducted to obtain a stress-strain curve under a high-strain-rate loading. Inverse analysis based on differential evolution was conducted to estimate undetermined variables for constitutive equations. Finally, the relationship between the attenuation factor and the strain rate in viscoelastic-plastic rock-like materials was investigated. According to the results, the frequency of the stress wave, viscosity coefficient, modulus of elasticity, and density play dominant roles in the attenuation of the stress wave. The attenuation decreases with increasing strain rate, demonstrating strongly strain-dependent attenuation in viscoelastic-plastic rock-like materials.

  20. Electrospun antimicrobial hybrid mats: Innovative packaging material for meat and meat-products.

    Science.gov (United States)

    Amna, Touseef; Yang, Jieun; Ryu, Kyeong-Seon; Hwang, I H

    2015-07-01

    To prevent the development and spread of spoilage/pathogenic microorganisms via meat foodstuffs, antimicrobial nanocomposite packaging can serve as a potential alternative. The objective of this study was to develop a new class of antimicrobial hybrid packaging mat composed of biodegradable polyurethane supplemented with virgin olive oil and zinc oxide via electrospinning. Instead of mixing antimicrobial compounds directly with food, incorporation in packaging materials allows the functional effect at food surfaces where microbial activity is localized. The nanofibers were characterized by SEM, EDX, XRD and TEM. The antibacterial activity was tested against two common foodborne pathogens viz., Staphylococcus aureus and Salmonella typhimurium. The present results indicated that incorporation of olive oil in the polymer affected morphology of PU nanofibers and nanocomposite packaging were able to inhibit growth of pathogens. Thus; as-spun mat can be used as prospective antimicrobial packaging, which potentially reduces contamination of meat/meat-products. Moreover, introduced biodegradable packaging for meat products could serve to replace PVC films and simultaneously help to protect natural environment.

  1. An analysis of the qualification criteria for small radioactive material shipping packages

    Energy Technology Data Exchange (ETDEWEB)

    McClure, J.D.

    1983-05-01

    The RAM package design certification process has two important elements, testing and acceptance. These terms sound very similar but they have specific meanings. Qualification testing in the context of this study is the imposition of simulated accident test conditions upon the candidate package design. (Normal transportation environments may also be included.) Following qualification testing, the acceptance criteria provide the performance levels which, if demonstrated, indicate the ability of the RAM package to sustain the severity of the qualification testing sequence and yet maintain specified levels of package integrity. This study has used Severities of Transportation Accidents as a data base to examine the regulatory test criteria which are required to be met by small packages containing Type B quantities of radioactive material (RAM). The basic findings indicate that the present regulatory test standards provide significantly higher levels of protection for the surface transportation modes (truck, rail) than for RAM packages shipped by aircraft. It should also be noted that various risk assessment studies have shown that the risk to the public due to severe transport accidents by surface and air transport modes is very low. A key element in this study was the quantification of the severity of the transportation accident environment and the severity of the present qualification test standards (called qualification test standards in this document) so that a direct comparison could be made between them to assess the effectiveness of the existing qualification test standards. The manner in which this was accomplished is described.

  2. Application of Quality by Design (QbD) Principles to Extractables/Leachables Assessment. Establishing a Design Space for Terminally Sterilized Aqueous Drug Products Stored in a Plastic Packaging System.

    Science.gov (United States)

    Jenke, Dennis

    2010-01-01

    The concept of quality by design (QbD) reflects the current global regulatory thinking related to pharmaceutical products. A cornerstone of the QbD paradigm is the concept of a design space, where the design space is a multidimensional combination of input variables and process parameters that have been demonstrated to provide the assurance of product quality. If a design space can be established for a pharmaceutical process or product, then operation within the design space confirms that the product or process output possesses the required quality attributes. This concept of design space can be applied to the safety (leachables) assessment of drug products manufactured and stored in packaging systems. Critical variables in such a design space would include those variables that affect the interaction of the drug product and its packaging, including (a) composition of the drug product, (b) composition of the packaging system, (c) configuration of the packaging system, and (d) the conditions of contact. This paper proposes and justifies such a leachables design space for aqueous drug products packaged in a specific plastic packaging system. Such a design space has the following boundaries:Aqueous drug products with a pH in the range of 2 to 8 and that contain no polarity-impacting agents such as organic solubilizers and stabilizers (addressing variable a). Packaging systems manufactured from materials that meet the system's existing material specifications (addressing variable b). Nominal fill volumes from 50 to 1000 mL (addressing variable c). Products subjected to terminal sterilization and then stored at room temperature for a period of up to 24 months (addressing variable d). The ramification of such a design space is that any drug product that falls within these boundaries is deemed to be compatible with the packaging system, from the perspective of safety, without the requirement of supporting drug product testing. When drug products are packaged in plastic

  3. Aluminum-thin-film packaged fiber Bragg grating probes for monitoring the maximum tensile strain of composite materials.

    Science.gov (United States)

    Im, Jooeun; Kim, Mihyun; Choi, Ki-Sun; Hwang, Tae-Kyung; Kwon, Il-Bum

    2014-06-10

    In this paper, new fiber Bragg grating (FBG) sensor probes are designed to intermittently detect the maximum tensile strain of composite materials, so as to evaluate the structural health status. This probe is fabricated by two thin Al films bonded to an FBG optical fiber and two supporting brackets, which are fixed on the surface of composite materials. The residual strain of the Al packaged FBG sensor probe is induced by the strain of composite materials. This residual strain can indicate the maximum strain of composite materials. Two types of sensor probes are prepared-one is an FBG with 18 μm thick Al films, and the other is an FBG with 36 μm thick Al films-to compare the thickness effect on the detection sensitivity. These sensor probes are bonded on the surfaces of carbon fiber reinforced plastics composite specimens. In order to determine the strain sensitivity between the residual strain of the FBG sensor probe and the maximum strain of the composite specimen, tensile tests are performed by universal testing machine, under the loading-unloading test condition. The strain sensitivities of the probes, which have the Al thicknesses of 18 and 36 μm, are determined as 0.13 and 0.23, respectively.

  4. 75 FR 16514 - Bayer Material Science, LLC, Formally Known as Sheffield Plastics, Including On-Site Leased...

    Science.gov (United States)

    2010-04-01

    ... Employment and Training Administration Bayer Material Science, LLC, Formally Known as Sheffield Plastics... Material Science, LLC, formally known as Sheffield Plastics, including on-site leased workers from... that Bayer Material Science, LLC was formally known as Sheffield Plastics. Some workers separated...

  5. Atomic layer deposition on polymer based flexible packaging materials: Growth characteristics and diffusion barrier properties

    Energy Technology Data Exchange (ETDEWEB)

    Kaeaeriaeinen, Tommi O., E-mail: tommi.kaariainen@lut.f [ASTRaL, Lappeenranta University of Technology, Prikaatinkatu 3 E, 50100 Mikkeli (Finland); Maydannik, Philipp, E-mail: philipp.maydannik@lut.f [ASTRaL, Lappeenranta University of Technology, Prikaatinkatu 3 E, 50100 Mikkeli (Finland); Cameron, David C., E-mail: david.cameron@lut.f [ASTRaL, Lappeenranta University of Technology, Prikaatinkatu 3 E, 50100 Mikkeli (Finland); Lahtinen, Kimmo, E-mail: kimmo.lahtinen@tut.f [Tampere University of Technology, Paper Converting and Packaging Technology, P.O. Box 541, 33101 Tampere (Finland); Johansson, Petri, E-mail: petri.johansson@tut.f [Tampere University of Technology, Paper Converting and Packaging Technology, P.O. Box 541, 33101 Tampere (Finland); Kuusipalo, Jurkka, E-mail: jurkka.kuusipalo@tut.f [Tampere University of Technology, Paper Converting and Packaging Technology, P.O. Box 541, 33101 Tampere (Finland)

    2011-03-01

    One of the most promising areas for the industrial application of atomic layer deposition (ALD) is for gas barrier layers on polymers. In this work, a packaging material system with improved diffusion barrier properties has been developed and studied by applying ALD on flexible polymer based packaging materials. Nanometer scale metal oxide films have been applied to polymer-coated papers and their diffusion barrier properties have been studied by means of water vapor and oxygen transmission rates. The materials for the study were constructed in two stages: the paper was firstly extrusion coated with polymer film, which was then followed by the ALD deposition of oxide layer. The polymers used as extrusion coatings were polypropylene, low and high density polyethylene, polylactide and polyethylene terephthalate. Water vapor transmission rates (WVTRs) were measured according to method SCAN-P 22:68 and oxygen transmission rates (O{sub 2}TRs) according to a standard ASTM D 3985. According to the results a 10 nm oxide layer already decreased the oxygen transmission by a factor of 10 compared to uncoated material. WVTR with 40 nm ALD layer was better than the level currently required for most common dry flexible packaging applications. When the oxide layer thickness was increased to 100 nm and above, the measured WVTRs were limited by the measurement set up. Using an ALD layer allowed the polymer thickness on flexible packaging materials to be reduced. Once the ALD layer was 40 nm thick, WVTRs and O{sub 2}TRs were no longer dependent on polymer layer thickness. Thus, nanometer scale ALD oxide layers have shown their feasibility as high quality diffusion barriers on flexible packaging materials.

  6. [Analysis of phthalate esters in plastic-packaging bags on-line sample stacking-microemulsion electrokinetic chromatography].

    Science.gov (United States)

    Xiao, Jia; Huang, Ying; Wang, Minyi; Chen, Guonan

    2012-09-01

    Two convenient, effective, and reproducible methods using microemulsion electrokinetic chromatography (MEEKC)-normal stacking mode (NSM) and reversed electrode polarity stacking mode (REPSM) were developed for the on-line sample stacking of phthalate esters (PAEs). REPSM coupled with MEEKC increased the sensitivity of 937.5 to 7,143 times for four PAEs compared to the conventional MEEKC. The separating conditions in the MEEKC method were studied, and many factors influencing the two sample stacking processes were investigated in detail. The optimum sample matrices for the two stacking methods were as follows: 30 mmol/L sodium cholate (SC) and 30.0 mmol/L borate (pH 8.5). Additionally, sample injections as large as 3.45 kPa x 40 s and 3.45 kPa x 90 s were applied for NSM-MEEKC and REPSM-MEEKC, respectively. The linear relationship and reproducibility were also examined. Under the optimum conditions, the detection limits (S/N = 3) of the PAEs were in the ranges of 0.021 - 0.33 mg/L and 0.7 - 4 microg/L for NSM-MEEKC and REPSM-MEEKC, respectively. The proposed REPSM-MEEKC has been successfully applied to determine PAEs in plastic-packaging bags, and the spiked recoveries were in the range of 89.1% - 105.6% with satisfactory results.

  7. Simulation of the dynamic response of radioactive material shipping package-railcar systems during coupling operations

    Energy Technology Data Exchange (ETDEWEB)

    Fields, S.R.

    1983-10-01

    The basic equations of the computer model CARDS (Cask-Railcar Dynamic Simulator), developed for the US Nuclear Regulatory Commission to simulate the dynamic behavior of radioactive material shipping package - railcar systems, are presented. A companion model, CARRS (Cask Railcar Response Spectrum Generator), that generates system response as frequency response spectra is also presented in terms of its basic equations. 1 reference, 18 figures.

  8. Simulation of the dynamic response of radioactive material shipping package - railcar systems during coupling operations

    Energy Technology Data Exchange (ETDEWEB)

    Fields, S.R.

    1981-12-01

    The basic equations of the computer model CARDS (Cask-Railcar Dynamic Simulator), developed for the U.S. Nuclear Regulatory Commission to simulate the dynamic behavior of radioactive material shipping package - railcar systems, are presented. A companion model, CARRS (Casks Railcar Response Spectrum Generator), that generates system response as frequency response spectra is also presented in terms of its basic equations.

  9. Study on Plastic Coated Overburnt Brick Aggregate as an Alternative Material for Bituminous Road Construction

    Directory of Open Access Journals (Sweden)

    Dipankar Sarkar

    2016-01-01

    Full Text Available There are different places in India where natural stone aggregates are not available for constructional work. Plastic coated OBBA can solve the problem of shortage of stone aggregate to some extent. The engineers are always encouraged to use locally available materials. The present investigation is carried out to evaluate the plastic coated OBBA as an alternative material for bituminous road construction. Shredded waste plastics are mixed with OBBA in different percentages as 0.38, 0.42, 0.46, 0.50, 0.54, and 0.60 of the weight of brick aggregates. Marshall Method of mix design is carried out to find the optimum bitumen content of such bituminous concrete mix prepared by plastic coated OBBA. Bulk density, Marshall Stability, flow, Marshall Quotient, ITS, TSR, stripping, fatigue life, and deformations have been determined accordingly. Marshall Stability value of 0.54 percent of plastic mix is comparatively higher than the other mixes except 0.60 percent of plastic mix. Test results are within the prescribed limit for 0.54 percent of plastic mix. There is a significant reduction in rutting characteristics of the same plastic mix. The fatigue life of the mix is also significantly higher. Thus plastic coated OBBA is found suitable in construction of bituminous concrete road.

  10. Surface modification of food contact materials for processing and packaging applications

    Science.gov (United States)

    Barish, Jeffrey A.

    This body of work investigates various techniques for the surface modification of food contact materials for use in food packaging and processing applications. Nanoscale changes to the surface of polymeric food packaging materials enables changes in adhesion, wettability, printability, chemical functionality, and bioactivity, while maintaining desirable bulk properties. Polymer surface modification is used in applications such as antimicrobial or non-fouling materials, biosensors, and active packaging. Non-migratory active packagings, in which bioactive components are tethered to the package, offer the potential to reduce the need for additives in food products while maintaining safety and quality. A challenge in developing non-migratory active packaging materials is the loss of biomolecular activity that can occur when biomolecules are immobilized. Polyethylene glycol (PEG), a biocompatible polymer, is grafted from the surface of ozone treated low-density polyethylene (LDPE) resulting in a surface functionalized polyethylene to which a range of amine-terminated bioactive molecules can be immobilized. The grafting of PEG onto the surface of polymer packaging films is accomplished by free radical graft polymerization, and to covalently link an amine-terminated molecule to the PEG tether, demonstrating that amine-terminated bioactive compounds (such as peptides, enzymes, and some antimicrobials) can be immobilized onto PEG-grafted LDPE in the development of non-migratory active packaging. Fouling on food contact surfaces during food processing has a significant impact on operating efficiency and can promote biofilm development. Processing raw milk on plate heat exchangers results in significant fouling of proteins as well as minerals, and is exacerbated by the wall heating effect. An electroless nickel coating is co-deposited with polytetrafluoroethylene onto stainless steel to test its ability to resist fouling on a pilot plant scale plate heat exchanger. Further

  11. Plastic film materials for dosimetry of very large absorbed doses

    DEFF Research Database (Denmark)

    McLaughlin, W.L.; Miller, Arne; Abdel-Rahim, F.

    1985-01-01

    Most plastic films have limited response ranges for dosimetry because of radiation-induced brittleness, degradation, or saturation of the signal used for analysis (e.g. spectrophotometry) at high doses. There are, however, a few types of thin plastic films showing linearity of response even up...... to doses as high as 2 × 106 Gy (200 Mrad) without severe loss of mechanical properties. Among many candidate film types tested, those showing such resistance to radiation damage and continued response at such high doses are polyethylene terephthalate, high-density polyethylene, dyed polyvinylchloride...

  12. Model for charge/discharge-rate-dependent plastic flow in amorphous battery materials

    Science.gov (United States)

    Khosrownejad, S. M.; Curtin, W. A.

    2016-09-01

    Plastic flow is an important mechanism for relaxing stresses that develop due to swelling/shrinkage during charging/discharging of battery materials. Amorphous high-storage-capacity Li-Si has lower flow stresses than crystalline materials but there is evidence that the plastic flow stress depends on the conditions of charging and discharging, indicating important non-equilibrium aspects to the flow behavior. Here, a mechanistically-based constitutive model for rate-dependent plastic flow in amorphous materials, such as LixSi alloys, during charging and discharging is developed based on two physical concepts: (i) excess energy is stored in the material during electrochemical charging and discharging due to the inability of the amorphous material to fully relax during the charging/discharging process and (ii) this excess energy reduces the barriers for plastic flow processes and thus reduces the applied stresses necessary to cause plastic flow. The plastic flow stress is thus a competition between the time scales of charging/discharging and the time scales of glassy relaxation. The two concepts, as well as other aspects of the model, are validated using molecular simulations on a model Li-Si system. The model is applied to examine the plastic flow behavior of typical specimen geometries due to combined charging/discharging and stress history, and the results generally rationalize experimental observations.

  13. CELLULOSIC PULPS OF CEREAL STRAWS AS RAW MATERIAL FOR THE MANUFACTURE OF ECOLOGICAL PACKAGING

    Directory of Open Access Journals (Sweden)

    Fátima Vargas,

    2012-07-01

    Full Text Available The aim of this work was to study the potential application of four types of cereal straws: oats, maize, rapeseed, and barley, in order to obtain cellulose pulp through the Specel® process for use in the manufacture of 100% biodegradable and ecological packaging. Raw materials were chemically characterized to determine alcohol-extractives, ash, lignin, holocellulose, and α-cellulose. Cellulosic pulps obtained from raw materials were characterized to determine yield, Kappa number, and viscosity. Paper sheets made from cellulosic pulps were characterized to determine beating degree, tensile index, stretch, burst index, tear index, and brightness. Finally, the results were compared to the raw material used in the industrial manufacturing of packaging (wheat. The four studied raw materials (oats, maize, rapeseed, and barley were judged to be suitable for use in the Specel® process to obtain cellulosic pulp suitable for production of ecological containers.

  14. Potential Biogenic Corrosion of Alloy 22, A Candidate Nuclear Waste Packaging Materials, Under Simulated Repository Conditions

    Energy Technology Data Exchange (ETDEWEB)

    Horn, J.M.; Martin, S.I.; Rivera, A.J.; Bedrossian, P.J.; Lian, T.

    2000-01-12

    The U.S. Department of Energy has been charged with assessing the suitability of a geologic nuclear waste repository at Yucca Mountain (YM), NV. Microorganisms, both those endogenous to the repository site and those introduced as a result of construction and operational activities, may contribute to the corrosion of metal nuclear waste packaging and thereby decrease their useful lifetime as barrier materials. Evaluation of potential Microbiological Influenced Corrosion (MIC) on candidate waste package materials was undertaken reactor systems incorporating the primary elements of the repository: YM rock (either non-sterile or presterilized), material coupons, and a continual feed of simulated YM groundwater. Periodically, both aqueous reactor efflux and material coupons were analyzed for chemical and surfacial characterization. Alloy 22 coupons exposed for a year at room temperature in reactors containing non-sterile YM rock demonstrated accretion of chromium oxide and silaceous scales, with what appear to be underlying areas of corrosion.

  15. Radiological properties of plastics and TLD materials its application in radiation dosimetry

    Science.gov (United States)

    Jabaseelan Samuel, E. James; Srinivasan, K.; Poopathi, V.

    2017-05-01

    In the current study, we evaluated the tissue equivalency of nine different commonly used thermoluminescence compounds and six plastic materials over the photon energy range of 15 KeV to 20 MeV. Our result confirmed that the ratio of number of electrons per gram, electron density of the entire TLD compounds and plastic materials to ICRU-44 soft tissue was lesser than unity, except in the case of polypropylene plastics. The effective atomic number ratio of all the plastic materials was also <1 excluding Poly-vinyl-chloride, and for TLD lithium borate material, it was <1 others which showed the deviation with respect to photon energy. Mass attenuation coefficient (µ/ϼ), mass absorption coefficient (µen/ρ) was calculated and the results are discussed in this paper.

  16. Compendium of information on identification and testing of materials for plastic solar thermal collectors

    Energy Technology Data Exchange (ETDEWEB)

    McGinniss, V.D.; Sliemers, F.A.; Landstrom, D.K.; Talbert, S.G.

    1980-07-31

    This report is intended to organize and summarize prior and current literature concerning the weathering, aging, durability, degradation, and testing methodologies as applied to materials for plastic solar thermal collectors. Topics covered include (1) rate of aging of polymeric materials; (2) environmental factors affecting performance; (3) evaluation and prediction of service life; (4) measurement of physical and chemical properties; (5) discussion of evaluation techniques and specific instrumentation; (6) degradation reactions and mechanisms; (7) weathering of specific polymeric materials; and (8) exposure testing methodology. Major emphasis has been placed on defining the current state of the art in plastics degradation and on identifying information that can be utilized in applying appropriate and effective aging tests for use in projecting service life of plastic solar thermal collectors. This information will also be of value where polymeric components are utilized in the construction of conventional solar collectors or any application where plastic degradation and weathering are prime factors in material selection.

  17. Application of x-ray stress measurement to practical materials for plastic work

    Energy Technology Data Exchange (ETDEWEB)

    Sekiguchi, Haruo; Kiriyama, Sadao

    1987-09-01

    X-ray diffraction stress measurement is achieved commonly from calculating elastic strain of crystal lattice. Therefore, the accuracy of the measurement is apt to be influenced from plastic zone or preferred orientation of surface layer for the measurement of practical materials with strong plastic work. It was found that the Two-Axis Oscillation Method was suitable to improve the accuracy of measurement on those materials. This papar discussed on the mechanism of residual stress mode during the process of plastic work, and described the application results on the plastic worked materials, such as spring steel surface treated by shot peening, titanium alloy with preferred orientation and mechanically worked surface of SUS 304 materials.

  18. Evaluation Of Gas Diffusion Through Plastic Materials Used In Experimental And Sampling Equipment

    DEFF Research Database (Denmark)

    Kjeldsen, Peter

    1993-01-01

    Plastic materials are often used in experimental and sampling equipment. Plastics are not gas tight, since gases are able to diffuse through the walls of tubing and containers made of plastic. Methods for calculating the significance of gas diffusion through the walls of containers and the walls....... Calculations show that diffusion of oxygen through plastic tubing and reactors into anoxic water can be a serious problem for a series of plastic materials. Comparison of the method for turbulent and laminar flow in tubings shows that the difference is insignificant for most cases. Calculations show also...... that the use of silicone rubber in experimental and sampling equipment to be used for anoxic water is, for most cases, prohibited by oxygen diffusion....

  19. Effect of packaging materials on the chemical composition and microbiological quality of edible mushroom (Pleurotus ostreatus) grown on cassava peels

    OpenAIRE

    Ajayi, Oluwakemi; Obadina, Adewale; Idowu, Micheal; Adegunwa, Mojisola; Kajihausa, Olatundun; Sanni, Lateef; Asagbra, Yemisi; Ashiru, Bolanle; Tomlins, Keith

    2015-01-01

    Edible fungi such as mushrooms are highly perishable and deteriorate few days after harvest due to its high moisture content and inability to maintain their physiological status. In this study, the effect of packaging materials on the nutritional composition of mushroom cultivated from cassava peels was investigated. Mushroom samples were dried at 50°C in a cabinet dryer for 8 h. The dried mushroom samples packaged in four different packaging materials; high density polyethylene (HDPE), polyp...

  20. Plastic Fibre Reinforced Soil Blocks as a Sustainable Building Material

    Science.gov (United States)

    Prasad, C. K. Subramania; Nambiar, E. K. Kunhanandan; Abraham, Benny Mathews

    2012-10-01

    Solid waste management, especially the huge quantity of waste plastics, is one of the major environmental concerns nowadays. Their employability in block making in the form of fibres, as one of the methods of waste management, can be investigated through a fundamental research. This paper highlights the salient observations from a systematic investigation on the effect of embedded fibre from plastic waste on the performance of stabilised mud blocks. Stabilisation of the soil was done by adding cement, lime and their combination. Plastic fibre in chopped form from carry bags and mineral water bottles were added (0.1% & 0.2% by weight of soil) as reinforcement. The blocks were tested for density, and compressive strength, and observed failure patterns were analysed. Blocks with 0.1% of plastic fibres showed an increase in strength of about 3 to 10%. From the observations of failure pattern it can be concluded that benefits of fibre reinforcement includes both improved ductility in comparison with raw blocks and inhibition of crack propogation after its initial formation.

  1. Applications of nanotechnology in food packaging and food safety: barrier materials, antimicrobials and sensors.

    Science.gov (United States)

    Duncan, Timothy V

    2011-11-01

    In this article, several applications of nanomaterials in food packaging and food safety are reviewed, including: polymer/clay nanocomposites as high barrier packaging materials, silver nanoparticles as potent antimicrobial agents, and nanosensors and nanomaterial-based assays for the detection of food-relevant analytes (gasses, small organic molecules and food-borne pathogens). In addition to covering the technical aspects of these topics, the current commercial status and understanding of health implications of these technologies are also discussed. These applications were chosen because they do not involve direct addition of nanoparticles to consumed foods, and thus are more likely to be marketed to the public in the short term.

  2. Material characterization and finite element modelling of cyclic plasticity behavior for 304 stainless steel using a crystal plasticity model

    OpenAIRE

    Lu, Jiawa; Sun, Wei; Becker, Adib A.

    2016-01-01

    Low cycle fatigue tests were carried out for a 304 stainless steel at room temperature. A series of experimental characterisations, including SEM, TEM, and XRD were conducted for the 304 stainless steel to facilitate the understanding of the mechanical responses and microstructural behaviour of the material under cyclic loading including nanostructure, crystal structure and the fractured surface. The crystal plasticity finite element method (CPFEM) is a powerful tool for studying the microstr...

  3. Insight into economies of scale for waste packaging sorting plants

    DEFF Research Database (Denmark)

    Cimpan, Ciprian; Wenzel, Henrik; Maul, Anja

    2015-01-01

    This contribution presents the results of a techno-economic analysis performed for German Materials Recovery Facilities (MRFs) which sort commingled lightweight packaging waste (consisting of plastics, metals, beverage cartons and other composite packaging). The study addressed the importance...... material streams....

  4. Development of non-woven and plastic composite medical sterilization packaging bags%一种无纺布与塑料复合型医用灭菌包装袋的研制

    Institute of Scientific and Technical Information of China (English)

    赵筠; 易江陵; 马旭东; 周廷云

    2012-01-01

    目的 试研制一种新型的无纺布与塑料复合型灭菌包装袋,为医疗器材灭菌包装提供新材料和新方法.方法 以透明耐高温医用复合塑料膜和SMS无纺布为原料,采用热溶压合和黏合的方法,试研制无纺布与塑料复合型的管状包装袋和独立包装袋,并且对所试研制包装袋,实施具有挑战性的灭菌包装质量试验和储存质量试验,两组试验样本各60包次.结果 试研制的无纺布与塑料复合型包装袋,在60包次灭菌包装质量试验中,未发生包装袋破损和暴边现象,也未发现灭菌湿包;而在60包次储存质量试验中包装袋器材灭菌后,储存6个月后抽检结果全部为阴性无菌生长.结论 我们研制的无纺布与塑料复合型灭菌包装袋质量较可靠,灭菌兼容性较强,性价比也较高,具有推广应用价值.%OBJECTIVE To develop a kind of non-woven and plastic composite medical sterilization packaging bags so as to provide new materials and new approaches for sterilized packaging of the medical devices. METHODS The transparent high-temperature composite plastic film and non-woven SMS were selected as the material , by the means of hot melt lamination and bonding, non-woven and plastic composite tubular packaging bags and individually wrapped bags were developed, the sterilization and packaging quality and the storage quality were tested for the newly developed bags, all the tested samples were divided into two groups with 60 packages in each. RESULTS Of 60 newly developed non-woven and plastic composite medical sterilization packaging bags for the quality test, there were no bags of breakage or burst side or humidified sterilized bags; and there were no bacterial growth that occurred after the storage for 6 months. CONCLUSION The quality of non-woven and plastic composite medical sterilization packaging bags we developed is feasible with stronger sterilization compatibility and higher cost-effect,which is worthy of

  5. The usage of plastic waste as a secondary raw material for the modification of sandcrete properties

    Science.gov (United States)

    Klovas, A.; Daukšys, M.; Venčkauskas, L.

    2015-03-01

    Recently the usage of various industry wastes as a secondary raw material tends to increase its relevancy. One of possible options to decrease the amount of waste is to use them to produce new products or materials. The operation of various secondary raw materials (tire rubber, tire cord, ground glass shards, ground ceramic waste products) during the concrete mixture preparation allows to change its as well as cured concrete properties. Recently polymer and steel fibers are used for concrete reinforcement. This study analyses the usage possibility of plastic shavings for the reinforcement of concrete. The technological properties of cement slurry (sand, fraction of 0/4 and 10 kg/m3, 15 kg/m3 and 20 kg/m3 of plastic shavings) as well as mechanical, physical and porosity properties of cured sandcrete were established during the experimental research. The geometric characteristics of mill-shredded plastic shavings were established. Experimental results revealed that the usage of plastic shavings decreased slurry slump and density. The minor decrease of cured sandcrete density (~2200 kg/m3) was noticed with the addition of plastic shavings within the limits of 10 - 20 kg/m3. The flexural strength of cured sandcrete increased from 36 % to 57 % compared with reference specimen (without plastic shavings). The dependence of flexural force and deflection was obtained. Study revealed that the residual strength after crack opening is bigger with the usage of plastic shavings as a secondary raw material compared with reference specimen.

  6. Optically stimulated luminescence of common plastic materials for accident dose reconstruction

    Energy Technology Data Exchange (ETDEWEB)

    Chang, I.; Lee, J. I.; Kim, J. L. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Chung, K. S. [Gyeongsang National Univ., Jinju (Korea, Republic of)

    2014-05-15

    Optically stimulate luminescence(OSL) has many applications in a variety of radiation dosimetry fields, including personal dosimetry, environmental radiation level monitor, retrospective dosimetry for dating, and reconstruction of radiation doses from radiation accident. In the reconstruction of radiation doses from radiation accident, OSL technique has been used to estimate the doses exposed to public area through analysis of housewares or house construing materials. Recently, many efforts have been carried out for dose reconstruction using personal electronic devices such as mobile phones and USB memory chips. Some of natural minerals such as quartz and feldspar have OSL properties. Quartz is the second most abundant mineral in continental crust of the Earth. In some of common plastics, inorganic fillers (quartz, alumina etc.) are added to make strengthen of their properties depends on applications areas. The aim of this research is to explore a possibility of use of the common plastic materials for dose reconstruction in radiation accident case. In this research the OSL dose response-curve and fading characteristics of the common plastics were tested and evaluated. Finally, we expect this work contribute to elevate the possibility of the dose reconstruction. The general conclusion of this work is that the possibility of dose reconstruction using common plastic materials is showed using the OSL characteristics of the materials. However, the tested common plastic materials have relatively low sensitivities. Further work is required to establish a database of OSL properties of common plastic materials for emergency dose reconstruction by using housewares.

  7. 21 CFR 509.15 - Use of polychlorinated biphenyls (PCB's) in establishments manufacturing food-packaging materials.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Use of polychlorinated biphenyls (PCB's) in establishments manufacturing food-packaging materials. 509.15 Section 509.15 Food and Drugs FOOD AND DRUG... polychlorinated biphenyls (PCB's) in establishments manufacturing food-packaging materials. (a) Polychlorinated...

  8. 21 CFR 109.15 - Use of polychlorinated biphenyls (PCB's) in establishments manufacturing food-packaging materials.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Use of polychlorinated biphenyls (PCB's) in establishments manufacturing food-packaging materials. 109.15 Section 109.15 Food and Drugs FOOD AND DRUG... polychlorinated biphenyls (PCB's) in establishments manufacturing food-packaging materials. (a) Polychlorinated...

  9. Wafer-level vacuum packaging for an optical readout bi-material cantilever infrared FPA

    Science.gov (United States)

    Li, Shuyu; Zhou, Xiaoxiong; Yu, Xiaomei

    2013-12-01

    In this paper, we report the design and fabrication of an uncooled infrared (IR) focal plane array (FPA) on quartz substrate and the wafer-level vacuum packaging for the IR FPA in view of an optical readout method. This FPA is composed of bi-material cantilever array which fabricated by the Micro-Electro Mechanical System (MEMS) technology, and the wafer-level packaging of the IR FPA is realized based on AuSn solder bonding technique. The interface of soldering is observed by scan electron microscope (SEM), which indicates that bonding interface is smooth and with no bubbles. The air leakage rate of packaged FPA is measured to be 1.3×10-9 atm·cc/s.

  10. Design of radioactive material shipping packaging for low-velocity puncture resistance

    Energy Technology Data Exchange (ETDEWEB)

    Nickell, R.E. (Electric Power Research Inst., Palo Alto, CA (USA)); May, R.A. (Sandia National Labs., Albuquerque, NM (USA))

    1983-02-01

    Both the standards developed by the International Atomic Energy Agency (IAEA) and those contained in the U.S. federal regulations stipulate that transport packagings containing large quantities of radioactive material, such as spent fuel from a nuclear power reactor or waste by-products from nuclear weapons programs, should be designed to resist a sequence of impact, puncture, fire, and water immersion conditions without harmful release of contents. A recent paper has offered a perspective on the design of such packagings relative to the impact event - a 30 ft (9m) drop onto an essentially unyielding target. In this paper the second event in the accident design sequence is addressed - the 40 in (1 m) drop of the packaging, after primary impact, onto a mild steel cylindrical punch.

  11. Multiscale Modeling of Structurally-Graded Materials Using Discrete Dislocation Plasticity Models and Continuum Crystal Plasticity Models

    Science.gov (United States)

    Saether, Erik; Hochhalter, Jacob D.; Glaessgen, Edward H.

    2012-01-01

    A multiscale modeling methodology that combines the predictive capability of discrete dislocation plasticity and the computational efficiency of continuum crystal plasticity is developed. Single crystal configurations of different grain sizes modeled with periodic boundary conditions are analyzed using discrete dislocation plasticity (DD) to obtain grain size-dependent stress-strain predictions. These relationships are mapped into crystal plasticity parameters to develop a multiscale DD/CP model for continuum level simulations. A polycrystal model of a structurally-graded microstructure is developed, analyzed and used as a benchmark for comparison between the multiscale DD/CP model and the DD predictions. The multiscale DD/CP model follows the DD predictions closely up to an initial peak stress and then follows a strain hardening path that is parallel but somewhat offset from the DD predictions. The difference is believed to be from a combination of the strain rate in the DD simulation and the inability of the DD/CP model to represent non-monotonic material response.

  12. 49 CFR 173.62 - Specific packaging requirements for explosives.

    Science.gov (United States)

    2010-10-01

    ... filled with water saturated material such as an anti-freeze solution or wetted cushioning 2. Outer packagings must be filled with water saturated material such as an anti-freeze solution or wetted cushioning... Bagspaper, Kraft paper, multiwall, water resistant plastics textile textile, rubberized plastics...

  13. INVESTIGATION OF THE PRESENCE OF DRUGSTORE BEETLES WITHIN CELOTEX ASSEMBLIES IN RADIOACTIVE MATERIAL PACKAGINGS

    Energy Technology Data Exchange (ETDEWEB)

    Loftin, B; Glenn Abramczyk, G

    2008-06-04

    During normal operations at the Department of Energy's Hanford Site in Hanford, WA, drugstore beetles, (Stegobium paniceum (L.) Coleoptera: Anobiidae), were found within the fiberboard subassemblies of two 9975 Shipping Packages. Initial indications were that the beetles were feeding on the Celotex{trademark} assemblies within the package. Celotex{trademark} fiberboard is used in numerous radioactive material packages serving as both a thermal insulator and an impact absorber for both normal conditions of transport and hypothetical accident conditions. The Department of Energy's Packaging Certification Program (EM-63) directed a thorough investigation to determine if the drugstore beetles were causing damage that would be detrimental to the safety performance of the Celotex{trademark}. The Savannah River National Laboratory is conducting the investigation with entomological expertise provided by Clemson University. The two empty 9975 shipping packages were transferred to the Savannah River National Laboratory in the fall of 2007. This paper will provide details and results of the ongoing investigation.

  14. Practical Thermal Evaluation Methods For HAC Fire Analysis In Type B Radiaoactive Material (RAM) Packages

    Energy Technology Data Exchange (ETDEWEB)

    Abramczyk, Glenn; Hensel, Stephen J; Gupta, Narendra K.

    2013-03-28

    Title 10 of the United States Code of Federal Regulations Part 71 for the Nuclear Regulatory Commission (10 CFR Part 71.73) requires that Type B radioactive material (RAM) packages satisfy certain Hypothetical Accident Conditions (HAC) thermal design requirements to ensure package safety during accidental fire conditions. Compliance with thermal design requirements can be met by prototype tests, analyses only or a combination of tests and analyses. Normally, it is impractical to meet all the HAC using tests only and the analytical methods are too complex due to the multi-physics non-linear nature of the fire event. Therefore, a combination of tests and thermal analyses methods using commercial heat transfer software are used to meet the necessary design requirements. The authors, along with his other colleagues at Savannah River National Laboratory in Aiken, SC, USA, have successfully used this 'tests and analyses' approach in the design and certification of several United States' DOE/NNSA certified packages, e.g. 9975, 9977, 9978, 9979, H1700, and Bulk Tritium Shipping Package (BTSP). This paper will describe these methods and it is hoped that the RAM Type B package designers and analysts can use them for their applications.

  15. Tendências e desafios da reciclagem de embalagens plásticas Trends and challenges in recycling plastic packages

    Directory of Open Access Journals (Sweden)

    Amélia S. F. Santos

    2004-12-01

    Full Text Available No gerenciamento do resíduo sólido urbano (RSU, a reciclagem surge como uma das vias para reduzir os resíduos sólidos aterrados em solo. Os plásticos constituem uma das classes de materiais com menor índice de reciclagem. Neste trabalho, as principais dificuldades encontradas em diversos países para aumentar os índices de reciclagem dos plásticos e as propostas que estão sendo utilizadas para mudar este cenário foram apresentadas. Por último, também foi apresentado um panorama geral sobre as exigências e limitações do retorno do plástico reciclado para alimentos. Este segmento representa todo um nicho de mercado que pode agregar valor e, principalmente, aumentar os índices de reciclagem de modo sustentável desde que haja investimentos em tecnologias inovadoras e economicamente viáveis.In the management of municipal solid waste (MSW, recycling emerges as one of the ways to reduce the solid wastes deposited in landfills. Plastics are one of the classes of materials with the lowest recycling index. The present study deals with the main difficulties encountered in different countries to increase plastics recycling and the procedures adopted to change this scenario. Additionally, the general requirements and the restrictions about the use of recycled plastic for food contact are presented. This application represents a whole market share to be explored, which could add value and increase the recycling indexes in a sustainable way, provided that investments in innovative technologies are made.

  16. Investigation of migrant-polymer interaction in pharmaceutical packaging material using the linear interaction energy algorithm.

    Science.gov (United States)

    Feenstra, Peter; Brunsteiner, Michael; Khinast, Johannes

    2014-10-01

    The interaction between drug products and polymeric packaging materials is an important topic in the pharmaceutical industry and often associated with high costs because of the required elaborative interaction studies. Therefore, a theoretical prediction of such interactions would be beneficial. Often, material parameters such as the octanol water partition coefficient are used to predict the partitioning of migrant molecules between a solvent and a polymeric packaging material. Here, we present the investigation of the partitioning of various migrant molecules between polymers and solvents using molecular dynamics simulations for the calculation of interaction energies. Our results show that the use of a model for the interaction between the migrant and the polymer at atomistic detail can yield significantly better results when predicting the polymer solvent partitioning than a model based on the octanol water partition coefficient.

  17. Reciclagem de materiais plásticos: a importância da identificação correta Plastic materials recycling: the importance of the correct identification

    Directory of Open Access Journals (Sweden)

    Leda Coltro

    2008-06-01

    Full Text Available Muitos produtos de material plástico apresentam código de identificação (normalmente um número de 1 a 7 dentro de um triângulo de três setas e sob o mesmo uma abreviatura indicando o tipo de plástico do qual o produto é feito para auxiliar sua separação e posterior reciclagem e revalorização, contribuindo com a recuperação dos materiais plásticos descartados com o resíduo sólido urbano. Como as embalagens têm rotatividade alta, é importante que as mesmas apresentem o símbolo de identificação da resina a fim de facilitar a cadeia de reciclagem do plástico. Neste trabalho, foi feito um levantamento de dados sobre os símbolos de identificação dos materiais plásticos em um total de 177 embalagens plásticas rígidas para o acondicionamento de diversos produtos alimentícios e não alimentícios disponíveis no mercado brasileiro. Apesar da norma brasileira ABNT NBR 13230 já ter 14 anos, há ainda heterogeneidade na identificação das embalagens plásticas. Somente cerca de 80% das embalagens avaliadas apresentaram o símbolo de identificação da resina. Além disso, em alguns casos até 40% das embalagens apresentaram a identificação do material de forma incorreta. Portanto, ainda existe informação errônea no mercado brasileiro sobre o tipo de material da embalagem plástica (incluindo ausência do símbolo de identificação, bem como falta de informação sobre o símbolo correto de identificação da resina, sendo que ambos os fatores prejudicam a cadeia de reciclagem do plástico.Many plastic-based products show a resin identification code - usually a number from 1 to 7 inside a three-arrow triangle above a monogram - to identify the type of plastic used to make the product, for assisting in its separation and later recycling. In other words, to facilitate the recovery of plastics discarded with the municipal solid waste. Since packages have a high rotation, the presence of the resin identification code is

  18. BIOFILTERS IN WASTEWATER TREATMENT AFTER RECYCLED PLASTIC MATERIALS

    Directory of Open Access Journals (Sweden)

    Irena Kania-Surowiec

    2014-10-01

    Full Text Available In this paper the possibility of using biological deposits in wastewater treatment of recycled plastics were presented. There are many aspects of this issue that should be considered to be able to use information technology solutions in the industry. This includes, inter alia, specify the types of laboratory tests based on the analysis of changes in the fluid during the wastewater treatment process, knowledge and selection factors for proper growth of biofilm in the deposit and to develop the right concept and a prototype for a particular processing plant, plastic processing plant. It is possible to determine the parameters that will increase the efficiency of sewage treatment while minimizing the financial effort on the part of the Company. Selection methods of wastewater treatment is also associated with the environmental strategy of the country at the enterprise level specified in the Environmental Policy. This is an additional argument for the use of biological methods in the treatment of industrial waste water.

  19. Plastic film materials for dosimetry of very large absorbed doses

    DEFF Research Database (Denmark)

    McLaughlin, W.L.; Miller, Arne; Abdel-Rahim, F.

    1985-01-01

    of the polyhalostyrenes have essentially rate-independent and moderately temperature-dependent responses to such large doses of ionizing radiation. While radiation-induced optical absorption in the ultraviolet for polystyrene is unstable following irradiation, thus leading to an intrinsic low-intensity rate dependence......Most plastic films have limited response ranges for dosimetry because of radiation-induced brittleness, degradation, or saturation of the signal used for analysis (e.g. spectrophotometry) at high doses. There are, however, a few types of thin plastic films showing linearity of response even up...... to doses as high as 2 × 106 Gy (200 Mrad) without severe loss of mechanical properties. Among many candidate film types tested, those showing such resistance to radiation damage and continued response at such high doses are polyethylene terephthalate, high-density polyethylene, dyed polyvinylchloride...

  20. Implementation of Control Measures for Radioactive Waste Packages with Respect to the Materials Composition - 12365

    Energy Technology Data Exchange (ETDEWEB)

    Steyer, S.; Kugel, K. [Federal Office for Radiation Protection (BfS), Salzgitter (Germany); Brennecke, P. [Braunschweig (Germany); Boetsch, W.; Gruendler, D.; Haider, C. [ISTec, Cologne (Germany)

    2012-07-01

    In addition to the radiological characterization and control measures the materials composition has to be described and respective control measures need to be implemented. The approach to verify the materials composition depends on the status of the waste: - During conditioning of raw waste the control of the materials composition has to be taken into account. - For already conditioned waste a retrospective qualification of the process might be possible. - If retrospective process qualification is not possible, legacy waste can be qualified by spot checking according to the materials composition requirements The integration of the control of the material composition in the quality control system for radioactive waste is discussed and examples of control measures are given. With the materials-list and the packaging-list the Federal Office for Radiation Protection (BfS) provides an appropriate tool to describe the materials composition of radioactive waste packages. The control measures with respect to the materials composition integrate well in the established quality control framework for radioactive waste. The system is flexible enough to deal with waste products of different qualities: raw waste, qualified conditioned waste or legacy waste. Control measures to verify the materials composition can be accomplished with minimal radiation exposure and without undue burden on the waste producers and conditioners. (authors)

  1. Using ProModel as a simulation tools to assist plant layout design and planning: Case study plastic packaging factory

    Directory of Open Access Journals (Sweden)

    Pochamarn Tearwattanarattikal

    2008-01-01

    Full Text Available This study is about the application of a Simulation Model to assist decision making on expanding capacity and plant layout design and planning. The plant layout design concept is performed first to create the physical layouts then the simulation model used to test the capability of plant to meet various demand forecast scena. The study employed ProModel package as a tool, using the model to compare the performances in term of % utilization, characteristics of WIP and ability to meet due date. The verification and validation stages were perform before running the scenarios. The model runs daily production and then the capacity constraint resources defined by % utilization. The expanding capacity policy can be extra shift-working hours or increasing the number of machines. After expanding capacity solutions are found, the physical layout is selected based on the criterion of space available for WIP and easy flow of material.

  2. Legal analysis of information displayed on dental material packages: An exploratory research

    Directory of Open Access Journals (Sweden)

    Bhumika Rathore

    2016-01-01

    Full Text Available Introduction: Some of the dental materials possess occupational hazards, preprocedural errors, and patient allergies as suggested by evidence. With due consideration to safety of the patients and dental professionals, it is essential that the trade of these materials is in conformity with the law. Aim: To perform the legal analysis of the information displayed on the packaging of dental materials. Materials and Methods: The Bureau of Indian Standards sets guidelines for packaging and marketing of dental products in India. An exploratory cross-sectional study was performed using various search engines and websites to access the laws and regulations existing pertaining to dental materials packaging. Based on the data obtained, a unique packaging standardization checklist was developed. Dental laboratory and impression plasters, alginates, and endodontic instruments were surveyed for all the available brands. This study considered 16 brands of plasters and alginates and 42 brands of endodontic instruments for legal analysis. Legal analysis was performed using the direct observation checklist. Descriptive statistics were obtained using SPSS version 19. Results: The guidelines set by the Bureau of Indian Standards do exist but are not updated and stand as oblivious guards for marketing standards. Overall compliance to the guidelines was reported to be 18.5% by brands of alginates, 4.1% by plaster of Paris, and 11.11% by endodontic instruments. Wave One™ File reported maximum adherence with the guidelines as 66.7%. Conclusion: This study found lower rate of adherence to the guidelines, thus indicating insufficient information being disclosed to the consumers.

  3. MIGRESIVES: a research project on migration from adhesives in food-packaging materials in support of European legislation and standardization.

    Science.gov (United States)

    Störmer, A; Franz, R

    2009-12-01

    Most food packages and food-contact materials are manufactured using adhesives. The European Union regulates all food-contact materials, as their constituents may not contaminate food and endanger consumers' health. In contrast to plastics which are regulated by positive lists of authorized ingredients, adhesives have not yet a specific regulation. The MIGRESIVES project aimed to elaborate a scientific global risk-assessment approach to meet current general European Union regulatory requirements and as a basis for future specific European Union legislation as well as to provide the industry, especially small and medium-sized enterprises, a tool to ensure that migration from adhesives is in compliance with the regulatory requirements. The idea was to demonstrate that consumers' exposure to chemicals released by adhesives is in many cases below levels of concern. Technical/scientific knowledge from industry and research institutes will be merged into a collective research endeavour gathering all stakeholders. The major milestones are (1) the classification of adhesives according to chemistry and uses, (2) the test strategies based on physico-chemical behaviour of adhesives, (3) modelling migration/exposure from adhesives, (4) providing guidelines to integrate the risk-assessment approach into the daily life of companies, (5) the feasibility of applying the toxicological approach from the European Union BIOSAFEPAPER project, and (6) extensive training/education to small and medium-sized enterprises (SMEs) and large dissemination for general adoption of the concept in Europe.

  4. An experimental study of plastic deformation of materials

    DEFF Research Database (Denmark)

    Knudsen, Tine

    in the investigated hot deformed samples (lnZ= 27.5 to 32) in general are cell block structures, and that the alignment of the cell block boundaries at low strain depends on the grain orientation, often in the same manner as in cold deformation. Part II investigates the energy stored in the dislocation structure...... after cold deformation by calorimetry and by analysis of the dislocation structure. The stored energy measured by calorimetry is found to be larger than that determined from the dislocation structure by a factor between 1.9 and 2.7, and this factor decreases with the plastic strain. Part III aimed...

  5. MATERIALS COMPATIBILITY OF SNAP FUEL COMPONENTS DURING SHIPMENT IN 9975 PACKAGING

    Energy Technology Data Exchange (ETDEWEB)

    Vormelker, P

    2006-11-14

    Materials Science and Technology has evaluated materials compatibility for the SNAP (Systems for Nuclear Auxiliary Power) fuel for containment within a 9975 packaging assembly for a shipping period of one year. The evaluation included consideration for potential for water within the convenience can, corrosion from water, galvanic corrosion, tape degradation, and thermal expansion risk. Based on a review of existing literature and assumed conditions, corrosion and/or degradation of the 304 stainless steel (SS) Primary Containment Vessel (PCV) and the 304 stainless steel convenience cans containing the SNAP fuel is not significant to cause failure during the 1 year time shipping period in the 9975 packaging assembly. However, storage beyond the 1 year shipping period has not been validated.

  6. Analysis of Counterfeit Coated Tablets and Multi-Layer Packaging Materials Using Infrared Microspectroscopic Imaging.

    Science.gov (United States)

    Winner, Taryn L; Lanzarotta, Adam; Sommer, André J

    2016-06-01

    An effective method for detecting and characterizing counterfeit finished dosage forms and packaging materials is described in this study. Using attenuated total internal reflection Fourier transform infrared spectroscopic imaging, suspect tablet coating and core formulations as well as multi-layered foil safety seals, bottle labels, and cigarette tear tapes were analyzed and compared directly with those of a stored authentic product. The approach was effective for obtaining molecular information from structures as small as 6 μm.

  7. THE TYPE OF PACKAGING MATERIAL AND STORAGE CONDITIONS AS FACTORS FOR WHEAT SEED QUALITY

    Directory of Open Access Journals (Sweden)

    Josip Šimenić

    2000-12-01

    Full Text Available Seed of cereal is normally grown on 5-8% of the overall plots under cereals in the Republic of Croatia. The produced seed meets the needs for high quality seed of wheat, barley, oat and other cereals. Certain quantities of seed remain unsold every year and are kept at various storage conditions and in various packaging material. The objective of this paper was to find out which storage conditions and what sort of packaging material would provide for the best viability of wheat seed. The investigation was carried out at storage simulation and by using various packaging material. In addition to well-known packaging material, such as paper 2 and 4-layer bags, jute bags, and PPR bags, the seed was also packed in the PVC transparent and PVC black bags, as well as in bags made of Aluminium foil. The investigation lasted for two years and was carried out in three various storage conditions, such as in the "New Warehouse" - a warehouse of a new type with thermal isolation in the roof and with uncontrolled conditions, ii the "Old Warehouse" made of filled-in brick and with a roof made of asbestos board, and iii under the "Eaves". The results have shown that the best seed was obtained when packed in 2 and 4-layer paper bags, PVC transparent bags and those made of Aluminium foil. Poorer results were obtained with bags of jute, polypropeline bags and PVC black bags. The storage of seed at "Eaves" has attained the best results in both years of the investigation, as compared to all three types of storage and it can in our circumstances meet the needs for wheat seed storage during one year

  8. Directory of Certificates of Compliance for radioactive materials packages: Report of NRC approved packages. Volume 1, Revision 18

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-10-01

    The purpose of this directory is to make available a convenient source of information on packagings which have been approved by the US Nuclear Regulatory Commission. To assist in identifying packaging, an index by Model Number and corresponding Certificate of Compliance Number is included at the front of Volumes 1 and 2. An alphabetical listing by user name is included in the back of Volume 3 of approved QA programs. The reports include a listing of all users of each package design and approved QA programs prior to the publication date.

  9. The Effects of Weathering on Mechanical Properties of Glass Fiber Reinforced Plastics (Grp) Materials

    OpenAIRE

    Abdullah, H.; S. Al Araimi and R. A. Siddiqui

    2012-01-01

    Glass fiber reinforced plastics composite is extensively used as a structural material for pools, oil pipes and tanks because it has good corrosion resistance properties.  The effects of weathering on the mechanical properties of glass fiber reinforced plastics (GRP) in the Sultanate of Oman have been studied.  The tensile and three point bend specimens were exposed to outdoor conditions (open atmosphere) in sunlight and tested for various intervals of time.  It was observed th...

  10. Increased Performance of Thermoplastic Packaging Materials by Using a Mild Oxidizing Biobased Additive

    Directory of Open Access Journals (Sweden)

    Ferdinand Männle

    2012-01-01

    Full Text Available Green additives such as prodegradants based on natural fatty acids and iron can improve the environmental profile of thermoplastic packaging materials. We present two studies in which this is demonstrated. In the first study, the addition of a green prodegradant to a 5-layer gas barrier laminate during processing provided a laminate with significantly reduced oxygen transmission due to the resulting oxygen-consuming degradation process. The result shows that material reduction and cost efficiency of packaging laminates can be combined, since 5-layer laminates with reduced oxygen barrier layer thickness and retained gas barrier properties are feasible. The products are interesting from an ecological and economic aspect. In the second study, the addition of a green prodegradant to several qualities of polypropylene that are used in packaging applications leads to materials that are readily degraded in accelerated weathering. The molecular weight of the modified polypropylenes after 830 hours of accelerated weathering is reduced from typically 80.000 g/mole to 1.500–2.500 g/mole. At such molecular weight levels, digestion by microorganisms is feasible. The mild prodegradant used in the study does not lead to degradation during processing. Thermoplastics containing such additives are therefore fully recyclable provided that they have not been exposed to a long period of weathering.

  11. Finite element analysis of 3D elastic-plastic frictional contact problem for Cosserat materials

    Science.gov (United States)

    Zhang, S.; Xie, Z. Q.; Chen, B. S.; Zhang, H. W.

    2013-06-01

    The objective of this paper is to develop a finite element model for 3D elastic-plastic frictional contact problem of Cosserat materials. Because 3D elastic-plastic frictional contact problems belong to the unspecified boundary problems with nonlinearities in both material and geometric forms, a large number of calculations are needed to obtain numerical results with high accuracy. Based on the parametric variational principle and the corresponding quadratic programming method for numerical simulation of frictional contact problems, a finite element model is developed for 3D elastic-plastic frictional contact analysis of Cosserat materials. The problems are finally reduced to linear complementarity problems (LCP). Numerical examples show the feasibility and importance of the developed model for analyzing the contact problems of structures with materials which have micro-polar characteristics.

  12. Steady State Crack Propagation in Layered Material Systems Displaying Visco-plastic Behaviour

    DEFF Research Database (Denmark)

    Nielsen, Kim Lau

    2012-01-01

    The steady state fracture toughness of elastic visco-plastic materials is studied numerically, using both a conventional and a higher order model. Focus is on the combined effect of strain hardening, strain gradient hardening and strain rate hardening on cracking in layered material systems...

  13. Structural Transformations in Metallic Materials During Plastic Deformation

    Science.gov (United States)

    Zasimchuk, E.; Turchak, T.; Baskova, A.; Chausov, N.; Hutsaylyuk, V.

    2017-03-01

    In this paper, the structure formation during the plastic deformation of polycrystalline nickel and aluminum based alloy 2024-T3 is investigated. The possibility of the relaxation and synergetic structure formation is examined. It is shown the deformation softening to be due to the crystallization of the amorphous structure of hydrodynamics flow channels (synergetic structure) HC as micrograins and their subsequent growth. The possible mechanism of micrograins' growth is proposed. The deformation processes change the phase composition of the multiphase alloy 2024-T3. It is shown by the quantitative analysis of the structures which were deformed in different regimes of the alloy samples. A method for increasing of the fatigue life through a dynamic pre-deformation is suggested.

  14. Structural Transformations in Metallic Materials During Plastic Deformation

    Science.gov (United States)

    Zasimchuk, E.; Turchak, T.; Baskova, A.; Chausov, N.; Hutsaylyuk, V.

    2017-02-01

    In this paper, the structure formation during the plastic deformation of polycrystalline nickel and aluminum based alloy 2024-T3 is investigated. The possibility of the relaxation and synergetic structure formation is examined. It is shown the deformation softening to be due to the crystallization of the amorphous structure of hydrodynamics flow channels (synergetic structure) HC as micrograins and their subsequent growth. The possible mechanism of micrograins' growth is proposed. The deformation processes change the phase composition of the multiphase alloy 2024-T3. It is shown by the quantitative analysis of the structures which were deformed in different regimes of the alloy samples. A method for increasing of the fatigue life through a dynamic pre-deformation is suggested.

  15. Design of an innovative, ecological portable waste compressor for in-house recycling of paper, plastic and metal packaging waste.

    Science.gov (United States)

    Xevgenos, D; Athanasopoulos, N; Kostazos, P K; Manolakos, D E; Moustakas, K; Malamis, D; Loizidou, M

    2015-05-01

    Waste management in Greece relies heavily on unsustainable waste practices (mainly landfills and in certain cases uncontrolled dumping of untreated waste). Even though major improvements have been achieved in the recycling of municipal solid waste during recent years, there are some barriers that hinder the achievement of high recycling rates. Source separation of municipal solid waste has been recognised as a promising solution to produce high-quality recycled materials that can be easily directed to secondary materials markets. This article presents an innovative miniature waste separator/compressor that has been designed and developed for the source separation of municipal solid waste at a household level. The design of the system is in line with the Waste Framework Directive (2008/98/EC), since it allows for the separate collection (and compression) of municipal solid waste, namely: plastic (polyethylene terephthalate and high-density polyethylene), paper (cardboard and Tetrapak) and metal (aluminium and tin cans). It has been designed through the use of suitable software tools (LS-DYNA, INVENTROR and COMSOL). The results from the simulations, as well as the whole design process and philosophy, are discussed in this article. © The Author(s) 2015.

  16. 21 CFR 570.13 - Indirect food additives resulting from packaging materials prior sanctioned for animal feed and...

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Indirect food additives resulting from packaging materials prior sanctioned for animal feed and pet food. 570.13 Section 570.13 Food and Drugs FOOD AND DRUG... FOOD ADDITIVES General Provisions § 570.13 Indirect food additives resulting from packaging...

  17. 21 CFR 570.14 - Indirect food additives resulting from packaging materials for animal feed and pet food.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Indirect food additives resulting from packaging..., DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS FOOD ADDITIVES General Provisions § 570.14 Indirect food additives resulting from packaging materials for animal feed...

  18. Use and safety of pet, package material in contact with beverages

    Directory of Open Access Journals (Sweden)

    Gabriela CILINCĂ

    2010-12-01

    Full Text Available Polyethylene terephthalate (PET is a long-chain polymer belonging to the generic family of polyesters. PET has found increasing applications within the food packaging field. The aim of the study was to survey the behavior of materials intended to come in contact with non-alcoholic or alcoholic beverages of an alcoholic concentration greater than 5% vol., like fruit juices, sparkling water, beer and others. The conclusion was that PET is a stable material, the value of global migration of components in selectedsimulants being in compliance with the legislation’s requirements (10 mg/dm2 or 60 mg/kg of food.

  19. Use and application of gelatin as potential biodegradable packaging materials for food products.

    Science.gov (United States)

    Nur Hanani, Z A; Roos, Y H; Kerry, J P

    2014-11-01

    The manufacture and potential application of biodegradable films for food application has gained increased interest as alternatives to conventional food packaging polymers due to the sustainable nature associated with their availability, broad and abundant source range, compostability, environmentally-friendly image, compatibility with foodstuffs and food application, etc. Gelatin is one such material and is a unique and popularly used hydrocolloid by the food industry today due to its inherent characteristics, thereby potentially offering a wide range of further and unique industrial applications. Gelatin from different sources have different physical and chemical properties as they contain different amino acid contents which are responsible for the varying characteristics observed upon utilization in food systems and when being utilized more specifically, in the manufacture of films. Packaging films can be successfully produced from all gelatin sources and the behaviour and characteristics of gelatin-based films can be altered through the incorporation of other food ingredients to produce composite films possessing enhanced physical and mechanical properties. This review will present the current situation with respect to gelatin usage as a packaging source material and the challenges that remain in order to move the manufacture of gelatin-based films nearer to commercial reality.

  20. Industrial Fuel Gas Demonstration Plant Program. Bid packages for materials (Deliverable No. 28)

    Energy Technology Data Exchange (ETDEWEB)

    None

    1979-01-01

    Fixed-price supply type bid packages for materials and/or service essentially are comprised of two parts, namely: (1) a technical requisition of the material, equipment, or service to be supplied; and (2) commercial and legal requirements, normally referred to as terms and conditions. Requisitions, providing technical requirements, for all equipment items identified for the Industrial Fuel Gas Demonstration Plant may be found in the 12 volumes of the Demonstration Plant Mechanical Design. The requisitions have been included within separate sections of the design report, sorted by appropriate plant unit. Combined with any General Notes Requisition and the necessary FWEC Job Standards, these various item requisitions provide all technical information for the prospective vendor to furnish his bid. The terms and conditions (boiler plate) to be included in the bid package identify all the contractual requirements which will be imposed upon the bidder. These requirements cover the conditions he must meet to bid on the particular item as well as the clauses to be included within the eventual purchase order/subcontract. A typical package of such terms and conditions is included.

  1. 纸塑袋包装器械的灭菌质量研究%Study on sterilization quality of instruments with paper-plastic bag packaging

    Institute of Scientific and Technical Information of China (English)

    陈奕芳; 蒋景华; 罗耀菊; 雷燕斐

    2015-01-01

    OBJECTIVE To compare the effects of single and double paper‐plastic bag packaging on sterilization ef‐fectiveness ,incidence of wet bag and seal line cracking of instruments ,so as to explore the best way of packaging . METHODS A total of 720 pieces of instruments in need of paper‐plastic packaging from Nov .1 to Nov .30 ,2013 were randomly divided into the control group (362 pieces) and the experimental group (358 pieces) .The control group adopted single paper‐plastic bag packaging ,while the experimental group adopted double paper‐plastic bag packaging in way of paper in face of paper and plastic surface in face of plastic surface to seal .The sterilization rate ,the incidence of wet pack and the seal line cracking rate of instruments after sterilization were examined .The software SPSS13 .0 was used for statistical analysis .RESULTS The pass rate of sterilization was 100% and the sealing line cracking rate was 0 .28% in both groups ,the incidence of wet package rates were 0 .55 and 0 .84 re‐spectively for the control group and the experimental group .There were no significant differences .There were no obvious differences in the effect of packaged instruments on pressuresteam sterilization effectiveness ,the incidence of wet bag and sealing line cracking between the two groups .CONCLUSION Sterilization on instruments with double paper‐plastic packaging is reliable ,and the phenomenon of wet pack and seal line cracking is absent when sterilization .Thus ,double paper‐plastic packaging can be used as the packaging method for a single instrument , which can reduce packaging damage in the process of transportation and storage and effectively reduce the risk of hospital infections .%目的:比较单层与双层纸塑袋包装器械对灭菌包压力蒸汽灭菌的灭菌效果、湿包发生、灭菌时密封线开裂的影响,以探索最佳包装方式。方法选择2013年11月1-30日单件需纸塑包装的器械共720件,随机分成对

  2. Mechanisms of plastic deformation for powder materials in cold working

    Institute of Scientific and Technical Information of China (English)

    张连洪; 李双义

    2003-01-01

    To deal with the discontinuity of particulate media and subsequent uncertainty of stress, based on the probability theory for mechanics of particulate media, Mohr-Coulomb yield criterion of particulate media, and the theory of crystal deformation, we put forward the statistical mechanisms of deformation of powder materials in cold working and mechanism of texture development of the high temperature superconducting wire/tape. A new yield criterion of powder materials is proposed.

  3. Modeling shock responses of plastic bonded explosives using material point method

    Science.gov (United States)

    Shang, Hailin; Zhao, Feng; Fu, Hua

    2017-01-01

    Shock responses of plastic bonded explosives are modeled using material point method as implemented in the Uintah Computational Framework. Two-dimensional simulation model was established based on the micrograph of PBX9501. Shock loading for the explosive was performed by a piston moving at a constant velocity. Unreactive simulation results indicate that under shock loading serious plastic strain appears on the boundary of HMX grains. Simultaneously, the plastic strain energy transforms to thermal energy, causing the temperature to rise rapidly on grain boundary areas. The influence of shock strength on the responses of explosive was also investigated by increasing the piston velocity. And the results show that with increasing shock strength, the distribution of plastic strain and temperature does not have significant changes, but their values increase obviously. Namely, the higher the shock strength is, the higher the temperature rise will be.

  4. Packaging Technologies for 500 C SiC Electronics and Sensors: Challenges in Material Science and Technology

    Science.gov (United States)

    Chen, Liang-Yu; Neudeck, Philip G.; Behelm, Glenn M.; Spry, David J.; Meredith, Roger D.; Hunter, Gary W.

    2015-01-01

    This paper presents ceramic substrates and thick-film metallization based packaging technologies in development for 500C silicon carbide (SiC) electronics and sensors. Prototype high temperature ceramic chip-level packages and printed circuit boards (PCBs) based on ceramic substrates of aluminum oxide (Al2O3) and aluminum nitride (AlN) have been designed and fabricated. These ceramic substrate-based chip-level packages with gold (Au) thick-film metallization have been electrically characterized at temperatures up to 550C. The 96 alumina packaging system composed of chip-level packages and PCBs has been successfully tested with high temperature SiC discrete transistor devices at 500C for over 10,000 hours. In addition to tests in a laboratory environment, a SiC junction field-effect-transistor (JFET) with a packaging system composed of a 96 alumina chip-level package and an alumina printed circuit board was tested on low earth orbit for eighteen months via a NASA International Space Station experiment. In addition to packaging systems for electronics, a spark-plug type sensor package based on this high temperature interconnection system for high temperature SiC capacitive pressure sensors was also developed and tested. In order to further significantly improve the performance of packaging system for higher packaging density, higher operation frequency, power rating, and even higher temperatures, some fundamental material challenges must be addressed. This presentation will discuss previous development and some of the challenges in material science (technology) to improve high temperature dielectrics for packaging applications.

  5. 废旧无菌复合包装材料铝塑分离技术研究进展%Research Progress of Separation Technology of Aluminum-plastic in Aseptic Composite Packaging

    Institute of Scientific and Technical Information of China (English)

    张素风; 梅星贤; 张璐璐

    2012-01-01

    The amount of waste aluminum-plastic composite packaging, which contains a large number of high quality fibers and aluminumplastic materials increases year by year. In the present paper, separation technologies of aluminum-plastic composites in the world were reviewed. The principle and processes of various separation approaches, such as separation with solvent, electrical separation and Argon electrolysis were analyzed and compared. Finally the existing problem of efficient separation and recycling as well as future research directions of aluminum-plastic composite were discussed.%文章综述了国内外铝塑分离技术的研究进展,分析和比较了溶剂法、高压静电分离、氩气电解等技术的基本原理和工艺过程等特点;指出铝塑高效分离再利用存在的问题及铝塑分离技术的未来研究方向.

  6. Determination Of Thermal And Mechanical Properties Of Packaging Materials For The Use In FEM-Simulations

    Science.gov (United States)

    Roellig, Mike; Boehme, Bjoern; Meier, Karsten; Metasch, René

    2011-09-01

    Conventional and future electronic packages merge several different materials. Polymers, metals, solders, dielectrics, glasses, silicon, composites come together and show strong mechanical and material interaction. These interfacial effects increase if the miniaturization and diversification keep on rising as it is proposed. Many efforts have to be done to assure the system reliability of new electronic packages. The Finite Element Simulation has the ability to support the development process of new packages. The application of the FEM-analysis requires the knowledge about the precise mechanical and thermal behaviour of the materials. The paper presents different measurement methods to determine accurate mechanical material properties of moulding compound polymers, underfillers, solder mask, and wafer photo resist and solder joints. The temperature dependency is essential to be respected. The polymer materials moulding compound as well as solder mask were characterized by Dynamic Mechanical Analysis under humidity influences to determine mechanical properties as function of moisture and temperature. Further experiments on polymer were conducted to extract the cure kinetics by Differential Scanning Calorimetry and to determine Bulk Modulus by Pressure-Volume-Temperature experiments (PVT). Altogether, these material properties need to be modeled in a comprehensive way fitting to each other. The common practice of just compiling data from different sources has been found to fail yielding in reliable and accurate results. The conditions under which the data were determined may cause mismatches between them and cause inconsistencies within the model. If a convergent solution was obtained at all, much simulation time would be needed as many iterations with small time steps were needed. In order to avoid this, the paper reports an approach of characterizing the temperature and time dependent mechanical material properties in one comprehensive scheme. The solder

  7. Plastic fish

    CERN Multimedia

    Antonella Del Rosso

    2015-01-01

    In terms of weight, the plastic pollution in the world’s oceans is estimated to be around 300,000 tonnes. This plastic comes from both land-based and ocean-based sources. A lecture at CERN by chemist Wolfgang Trettnak addressed this issue and highlighted the role of art in raising people’s awareness.   Artwork by Wolfgang Trettnak. Packaging materials, consumer goods (shoes, kids’ toys, etc.), leftovers from fishing and aquaculture activities… our oceans and beaches are full of plastic litter. Most of the debris from beaches is plastic bottles. “PET bottles have high durability and stability,” explains Wolfgang Trettnak, a chemist by education and artist from Austria, who gave a lecture on this topic organised by the Staff Association at CERN on 26 May. “PET degrades very slowly and the estimated lifetime of a bottle is 450 years.” In addition to the beach litter accumulated from human use, rivers bring several ki...

  8. Phase field crystal study of deformation and plasticity in nanocrystalline materials.

    Science.gov (United States)

    Stefanovic, Peter; Haataja, Mikko; Provatas, Nikolas

    2009-10-01

    We introduce a modified phase field crystal (MPFC) technique that self-consistently incorporates rapid strain relaxation alongside the usual plastic deformation and multiple crystal orientations featured by the traditional phase field crystal (PFC) technique. Our MPFC formalism can be used to study a host of important phase transformation phenomena in material processing that require rapid strain relaxation. We apply the MPFC model to study elastic and plastic deformations in nanocrystalline materials, focusing on the "reverse" Hall-Petch effect. Finally, we introduce a multigrid algorithm for efficient numerical simulations of the MPFC model.

  9. Validation of the material point method and plasticity with Taylor impact tests

    CERN Document Server

    Banerjee, Biswajit

    2012-01-01

    Taylor impacts tests were originally devised to determine the dynamic yield strength of materials at moderate strain rates. More recently, such tests have been used extensively to validate numerical codes for the simulation of plastic deformation. In this work, we use the material point method to simulate a number of Taylor impact tests to compare different Johnson-Cook, Mechanical Threshold Stress, and Steinberg-Guinan-Cochran plasticity models and the vob Mises and Gurson-Tvergaard-Needleman yield conditions. In addition to room temperature Taylor tests, high temperature tests have been performed and compared with experimental data.

  10. Public health impact of plastics: An overview

    Directory of Open Access Journals (Sweden)

    Neeti Rustagi

    2011-01-01

    Full Text Available Plastic, one of the most preferred materials in today′s industrial world is posing serious threat to environment and consumer′s health in many direct and indirect ways. Exposure to harmful chemicals during manufacturing, leaching in the stored food items while using plastic packages or chewing of plastic teethers and toys by children are linked with severe adverse health outcomes such as cancers, birth defects, impaired immunity, endocrine disruption, developmental and reproductive effects etc. Promotion of plastics substitutes and safe disposal of plastic waste requires urgent and definitive action to take care of this potential health hazard in future.

  11. Public health impact of plastics: An overview

    Science.gov (United States)

    Rustagi, Neeti; Pradhan, S. K.; Singh, Ritesh

    2011-01-01

    Plastic, one of the most preferred materials in today's industrial world is posing serious threat to environment and consumer's health in many direct and indirect ways. Exposure to harmful chemicals during manufacturing, leaching in the stored food items while using plastic packages or chewing of plastic teethers and toys by children are linked with severe adverse health outcomes such as cancers, birth defects, impaired immunity, endocrine disruption, developmental and reproductive effects etc. Promotion of plastics substitutes and safe disposal of plastic waste requires urgent and definitive action to take care of this potential health hazard in future. PMID:22412286

  12. Public health impact of plastics: An overview.

    Science.gov (United States)

    Rustagi, Neeti; Pradhan, S K; Singh, Ritesh

    2011-09-01

    Plastic, one of the most preferred materials in today's industrial world is posing serious threat to environment and consumer's health in many direct and indirect ways. Exposure to harmful chemicals during manufacturing, leaching in the stored food items while using plastic packages or chewing of plastic teethers and toys by children are linked with severe adverse health outcomes such as cancers, birth defects, impaired immunity, endocrine disruption, developmental and reproductive effects etc. Promotion of plastics substitutes and safe disposal of plastic waste requires urgent and definitive action to take care of this potential health hazard in future.

  13. Experimental investigations and numerical simulations of notch effect in cellular plastic materials

    Science.gov (United States)

    Marsavina, L.; Linul, E.; Voiconi, T.; Negru, R.

    2016-04-01

    Cellular plastics are light weight structures with many applications in civil, aeronautical, automotive and mechanical engineering. Properties of cellular materials depend on the properties of the solid material, on the shape and dimensions of the cellular structure and on the relative density of the cellular material. Most of cellular plastic materials are crushing in compression and have a brittle behavior in tension. The effect of notches represents an important issue in such materials, taking into account that for packing applications for example, notches/holes should be introduced in the cellular material. This paper investigates the effect of notches in compression for three different densities 100, 145 and 300 kg/m3 polyurethane (PUR) foams. Experimental investigations were performed on rectangular blocks of 100×100×25 mm with 16, 28 and 40 mm central holes. The mechanism of damage was monitored with an IR camera FLIR A40M. Purpose of the numerical simulations was to calibrate a material model, based on compression test for un-notched specimens using the CRUSHABLE FOAM models implemented in ABAQUS SIMULIA. Then the material models were used to simulate the experimental tests on notched blocks. Good agreement was obtained for the load - displacement curves obtained experimentally and from simulation. Also the plastic deformation patterns observed experimentally by IR thermograpghy were obtained numerically using the CRUSHABLE FOAM material model.

  14. From waste plastics to industrial raw materials: A life cycle assessment of mechanical plastic recycling practice based on a real-world case study.

    Science.gov (United States)

    Gu, Fu; Guo, Jianfeng; Zhang, Wujie; Summers, Peter A; Hall, Philip

    2017-12-01

    Mechanical recycling of waste plastics is an environmental solution to the problem of waste plastic disposal, and has already become a common practice in industry. However, limited information can be found on either the industralised plastic recycling or the recycled materials, despite the use of recycled plastics has already extended to automobile production. This study investigates the life cycle environmental impacts of mechanical plastic recycling practice of a plastic recycling company in China. Waste plastics from various sources, such as agricultural wastes, plastic product manufacturers, collected solid plastic wastes and parts dismantled from waste electric and electronic equipments, are processed in three routes with products end up in different markets. The results of life cycle assessments show that the extrusion process has the largest environmental impacts, followed by the use of fillers and additives. Compared to production of virgin plastics and composites, the mechanical recycling is proved to be a superior alternative in most environmental aspects. Substituting virgin plastic composites with recycled plastic composites has achieved the highest environmental benefits, as virgin composite production has an impact almost 4 times higher that of the recycled composite production in each ReCiPe endpoint damage factor. Sensitivity analysis shows that the coverage of collecting network contribute affect little to overall environmental impact, and centralisation plays an important role in reducing overall environmental impacts. Among the fillers and additives, impact modifiers account for the most significant contributions to the environmental impacts of recycled composites. This study provides necessary information about the existing industrialised plastic recycling practice, and recommendations are given. Research implications are presented with the purpose to achieve higher substitution rate and lower environmental impact. Copyright © 2017 Elsevier B

  15. Study of an athermal quasi static plastic deformation in a 2D granular material

    Science.gov (United States)

    Zhang, Jie; Zheng, Jie

    2016-11-01

    In crystalline materials, the plasticity has been well understood in terms of dynamics of dislocation, i.e. flow defects in the crystals where the flow defects can be directly visualized under a microscope. In a contrast, the plasticity in amorphous materials, i.e. glass, is still poorly understood due to the disordered nature of the materials. In this talk, I will discuss the recent results we have obtained in our ongoing research of the plasticity of a 2D glass in the athermal quasi static limit where the 2D glass is made of bi-disperse granular disks with very low friction. Starting from a densely packed homogeneous and isotropic initial state, we apply pure shear deformation to the system. For a sufficiently small strain, the response of the system is linear and elastic like; when the strain is large enough, the plasticity of the system gradually develops and eventually the shear bands are fully developed. In this study, we are particularly interested in how to relate the local plastic deformation to the macroscopic response of the system and also in the development of the shear bands.

  16. Influence of packaging materials on storage property of peanut under normal temperature%包装材料对常温花生耐贮性的影响

    Institute of Scientific and Technical Information of China (English)

    陈红; 熊利荣; 王晶; 万鹏; 胡筱波

    2012-01-01

    为了探讨包装材料对常温贮藏条件下花生耐贮性的影响,该文研究了常用的3种包装材料下花生色泽、含水率、电导率、发芽率、黄曲霉感染指数、防虫效果的变化规律.结果表明:包装对花生贮藏质量指标的影响非常显著.薄膜袋包装花生的红衣种皮颜色变化速度比编织袋和麻袋包装的缓慢;薄膜袋较强的保水能力能够有效地防止花生水分散失;但在贮藏初期,密闭的薄膜袋包装环境易造成无氧呼吸,引起花生种皮细胞膜结构和种胚损伤,导致电导率急剧增大;种皮是花生抵抗黄曲霉菌侵染的重要屏障,因此,薄膜袋包装的抗黄曲霉菌侵染能力低于编织袋和麻袋包装;编织袋和麻袋包装花生的发芽率略高于薄膜袋包装;3种包装方式抑制虫害繁殖作用差异显著,高通透性的编织袋和麻袋包装的花生害虫侵蚀严重,而薄膜袋包装可以有效地抑制虫害的发生.总之,花生品质的变化是一个动态的复杂过程,在选择适宜包装材料时应结合花生生理特性、贮藏环境等因素综合考虑,这为常温花生的贮藏提供了参考.%In order to study the influence of packaging materials on storaged peanut at normal temperature, the paper investigated the effects of commonly-used 3 types of packaging materials on peanut's color, moisture content, conductivity, germination percentage, Aspergillus flavus infection index and insecticidal effect. The results showed that the packaging materials had notable influences on peanut's storage quality index. The seed coat color change rate of peanut packaged in plastic film bag was slower than that in woven bag and sack. Meanwhile, the strong water-preservation ability of plastic film bag enabled itself to effectively prevent against water evaporation of peanuts. However, at the initial stage of storage, the closed package environment of plastic film bag can cause anaerobic respiration which will

  17. Chemistry with Inexpensive Materials: Spray Bottles and Plastic Bags.

    Science.gov (United States)

    Zoltewicz, Susan

    1993-01-01

    Presents eight chemistry activities that are interesting and involve simple, easily available materials. Topics include mystery writing, valentine hearts, flame tests, evaporation race, buoyancy versus mass, determination of relative masses of gases, mole sample container, and cold and hot packs. (DDR)

  18. Performance-oriented packaging: A guide to identifying and designing. Identifying and designing hazardous materials packaging for compliance with post HM-181 DOT Regulations

    Energy Technology Data Exchange (ETDEWEB)

    1994-08-01

    With the initial publication of Docket HM-181 (hereafter referred to as HM-181), the U.S. Department of Energy (DOE), Headquarters, Transportation Management Division decided to produce guidance to help the DOE community transition to performance-oriented packagings (POP). As only a few individuals were familiar with the new requirements, elementary guidance was desirable. The decision was to prepare the guidance at a level easily understood by a novice to regulatory requirements. This document identifies design development strategies for use in obtaining performance-oriented packagings that are not readily available commercially. These design development strategies will be part of the methodologies for compliance with post HM-181 U.S. Department of Transportation (DOT) packaging regulations. This information was prepared for use by the DOE and its contractors. The document provides guidance for making decisions associated with designing performance-oriented packaging, and not for identifying specific material or fabrication design details. It does provide some specific design considerations. Having a copy of the regulations handy when reading this document is recommended to permit a fuller understanding of the requirements impacting the design effort. While this document is not written for the packaging specialist, it does contain guidance important to those not familiar with the new POP requirements.

  19. Safety analysis report: packages. 232-H Byproduct Trailer (packaging of radioactive material). Final report. [Helium containing some tritium

    Energy Technology Data Exchange (ETDEWEB)

    Chalfant, G.G. (comp.)

    1975-12-01

    Helium containing some tritium is shipped at low pressure in banks of cylinders mounted on a truck trailer in compliance with 49 CFR 178.350, Specification 7A. The shipping package is not a radiological hazard under normal or accident conditions.

  20. Influence of some packaging materials and of natural tocopherols on the sensory properties of breakfast cereals.

    Science.gov (United States)

    Paradiso, Vito M; Caponio, Francesco; Summo, Carmine; Gomes, Tommaso

    2014-04-01

    The combined effect of natural antioxidants and packaging materials on the quality decay of breakfast cereals during storage was evaluated. Corn flakes were produced on industrial scale, using different packages and adding natural tocopherols to the ingredients, and stored for 1 year. The samples were then submitted to sensory analysis and HS-solid phase microextraction/gas chromatography/mass spectrometry (SPME/GC/MS) analysis. The packaging had a significant influence on the sensory profile of the aged product: metallized polypropylene gave the highest levels of oxidation compounds and sensory defects. The sensory profile was improved using polypropylene and especially high-density polyethylene. Natural tocopherols reduced the sensory decay of the flakes and the oxidative evolution of the volatile profile. They gave the most remarkable improvement in polypropylene (either metallized or not) packs. Polypropylene showed a barrier effect on the scalping of volatiles outside of the pack. This led to higher levels of oxidation volatiles and faster rates of the further oxidative processes involving the volatiles.

  1. Evaluation of bionanocomposites as packaging material on properties of soft white cheese during storage period.

    Science.gov (United States)

    Youssef, Ahmed M; El-Sayed, Samah M; Salama, Heba H; El-Sayed, Hoda S; Dufresne, A

    2015-11-05

    Novel bionanocomposites based on chitosan/poly(vinyl alcohol)/titanium nanoparticles (CS/PVA/TiO2 nanocomposite) were prepared and used as packaging materials for soft white cheese. The prepared bionanocomposites were characterized using XRD, SEM, TEM and FT-IR. The CS/PVA/TiO2 bionanocomposites exhibited good mechanical properties. Furthermore, the obtained bionanocomposites exhibited superior antibacterial activity against gram positive (Staphylococcus aureus), gram negative (Pseudomonas aeruginosa, Escherichia coli) bacteria and fungi (Candidia albicans). The soft white cheese was manufactured and packaged within the CS/PVA/TiO2 nanocomposite films and stored at 7 °C for 30 days. The color, rheological and chemical properties of cheese were evaluated, also the influence of CS/PVA/TiO2 bionanocomposites on microbiological analysis of soft white cheese was assessed, the results indicated that the total bacterial counts, mold & yeast and coliform decreased with the increasing storage period and disappeared at the end of storage period compared with control. Consequently, CS/PVA/TiO2 bionanocomposite can be used in food packaging applications.

  2. [Characterization of silver nanoparticles migration from package materials destined for contact with foods].

    Science.gov (United States)

    Smirnova, V V; Krasnoiarova, O V; Pridvorova, S M; Zherdev, A V; Gmoshinskiĭ, I V; Kazydub, G V; Popov, K I; Khotimchenko, S A

    2012-01-01

    There was studied migration of artificial silver nanoparticles from polyethylene films destined for package of such foods as bread and poultry into model media reproducing physico-chemical properties and composition of said products. Modification of films was performed by 5- or 10-fold spraying of silver nanoparticles on the surface of package material. Model media were composed from water, alcohol and plant oil according to US FDA and Russian Federal Service for Surveillance of Consumer Rights Protection and Human Well-Being official recommendation. Nanoparticles were detected in model media by means of transmission electron and atomic force microscopy. Quantification of silver in nanoparticles migrating from films was performed by mass-spectrometry with inductively coupled plasma. The results obtained showed that silver migrated from films into test media in form of nanoparticles with mean diameter close to 10-20 nm. Migrated particles were partially aggregated to complexes with dimension about 50 nm with degree of aggregation depending on media composition. Quantification showed that amounts of silver nanoparticles migrating in foods did not exceed save level of this nanomaterial consumption even in aggravated conditions when almost all volume of product was consumed in form packaged in films modified with nanosilver.

  3. Implicit integration of plasticity models for granular materials

    DEFF Research Database (Denmark)

    Ahadi, A.; Krenk, Steen

    2003-01-01

    A stress integration algorithm for granular materials based on fully implicit integration with explicit updating is presented. In the implicit method the solution makes use of the gradient to the potential surface at the final stress state which is unknown. The final stress and hardening parameters...... are determined solving the non-linear equations iteratively so that the stress increment fulfills the consistency condition. The integration algorithm is applicable for models depending on all the three stress invariants and it is applied to a characteristic state model for granular material. Since tensile...... of the integration algorithm are illustrated by simulating both drained and undrained triaxial tests on sand. The algorithm is developed in a standard format which can be implemented in several general purpose finite element codes. It has been implemented as an ABAQUS subroutine, and a traditional geotechnical...

  4. PLASTICITY OF SELECTED METALLIC MATERIALS IN DYNAMIC DEFORMATION CONDITIONS

    OpenAIRE

    2014-01-01

    Characteristics of a modernized flywheel machine has been presented in the paper. The laboratory stand enables to perform dynamic tensile tests and impact bending with a linear velocity of the enforcing element in the range of 5÷40 m/s. A new data acquisition system, based on the tensometric sensors, allows for significant qualitative improvement of registered signals. Some preliminary dynamic forming tests were performed for the selected group of metallic materials. Subsequent microstruct...

  5. 消毒供应中心包装材料的合理应用%Reasonable use of packaging materials in central sterile supply department

    Institute of Scientific and Technical Information of China (English)

    侯玉英; 王素英; 马红娟

    2014-01-01

    OBJECTIVE To investigate the status of application of sterile packaging materials in the central sterile supply department so as to provide guidance for reasonable use of packaging materials in the hospital .METHODS The related features of the commonly used cotton cloth ,rigid containers ,paper and plastic bags ,and disposable non-woven were observed and compared .RESULTS The sterilant penetration effect of the cotton cloth was excel-lent ,the rigid containers general ,the paper and plastic bags excellent ,the disposable non-woven excellent .The bacteria barrier level of the cotton cloth was zero or low ,the rigid containers general ,the paper and plastic bags excellent ,the disposable non-woven excellent .The sterilization validity period of the cotton cloth was 14 days ,the rigid containers 14 days ,the paper and plastic bags 180 days ,the disposable non-woven 180 days .The physical tolerance of the cotton cloth was excellent ,the rigid containers excellent ,the paper and plastic bags general ,the disposable non-woven excellent .The contamination degree of the cotton cloth was cotton dust contamination ,the rigid containers 0 ,the paper and plastic bags mild ,the disposable non-woven 0 .The use cost of the cotton cloth was low ,the rigid containers low ,the paper and plastic bags relatively high ,the disposable non-woven high . CONCLUSION It is an effective way to choose appropriate sterile packaging materials so as to not only ensure the quality of sterilization but also save the cost .%目的:探究消毒供应中心灭菌包装材料的应用情况,为医院合理使用包装材料提供参考。方法对医院常用的纯棉包布、硬质容器、纸塑包装袋及一次性无纺布4类灭菌包装材料的相关特性进行比较。结果纯棉包布、硬质容器、纸塑包装纸、一次性无纺布的灭菌剂穿透效果分别为优、一般、优、优;细菌屏障水平分别为无或低、一般、优、优;灭菌有效期分别为14、14

  6. Plastics recycling: challenges and opportunities.

    Science.gov (United States)

    Hopewell, Jefferson; Dvorak, Robert; Kosior, Edward

    2009-07-27

    Plastics are inexpensive, lightweight and durable materials, which can readily be moulded into a variety of products that find use in a wide range of applications. As a consequence, the production of plastics has increased markedly over the last 60 years. However, current levels of their usage and disposal generate several environmental problems. Around 4 per cent of world oil and gas production, a non-renewable resource, is used as feedstock for plastics and a further 3-4% is expended to provide energy for their manufacture. A major portion of plastic produced each year is used to make disposable items of packaging or other short-lived products that are discarded within a year of manufacture. These two observations alone indicate that our current use of plastics is not sustainable. In addition, because of the durability of the polymers involved, substantial quantities of discarded end-of-life plastics are accumulating as debris in landfills and in natural habitats worldwide. Recycling is one of the most important actions currently available to reduce these impacts and represents one of the most dynamic areas in the plastics industry today. Recycling provides opportunities to reduce oil usage, carbon dioxide emissions and the quantities of waste requiring disposal. Here, we briefly set recycling into context against other waste-reduction strategies, namely reduction in material use through downgauging or product reuse, the use of alternative biodegradable materials and energy recovery as fuel. While plastics have been recycled since the 1970s, the quantities that are recycled vary geographically, according to plastic type and application. Recycling of packaging materials has seen rapid expansion over the last decades in a number of countries. Advances in technologies and systems for the collection, sorting and reprocessing of recyclable plastics are creating new opportunities for recycling, and with the combined actions of the public, industry and governments it

  7. Plastics recycling: challenges and opportunities

    Science.gov (United States)

    Hopewell, Jefferson; Dvorak, Robert; Kosior, Edward

    2009-01-01

    Plastics are inexpensive, lightweight and durable materials, which can readily be moulded into a variety of products that find use in a wide range of applications. As a consequence, the production of plastics has increased markedly over the last 60 years. However, current levels of their usage and disposal generate several environmental problems. Around 4 per cent of world oil and gas production, a non-renewable resource, is used as feedstock for plastics and a further 3–4% is expended to provide energy for their manufacture. A major portion of plastic produced each year is used to make disposable items of packaging or other short-lived products that are discarded within a year of manufacture. These two observations alone indicate that our current use of plastics is not sustainable. In addition, because of the durability of the polymers involved, substantial quantities of discarded end-of-life plastics are accumulating as debris in landfills and in natural habitats worldwide. Recycling is one of the most important actions currently available to reduce these impacts and represents one of the most dynamic areas in the plastics industry today. Recycling provides opportunities to reduce oil usage, carbon dioxide emissions and the quantities of waste requiring disposal. Here, we briefly set recycling into context against other waste-reduction strategies, namely reduction in material use through downgauging or product reuse, the use of alternative biodegradable materials and energy recovery as fuel. While plastics have been recycled since the 1970s, the quantities that are recycled vary geographically, according to plastic type and application. Recycling of packaging materials has seen rapid expansion over the last decades in a number of countries. Advances in technologies and systems for the collection, sorting and reprocessing of recyclable plastics are creating new opportunities for recycling, and with the combined actions of the public, industry and governments it

  8. Study of silicone-based materials for the packaging of optoelectronic devices

    Science.gov (United States)

    Lin, Yeong-Her

    The first part of this work is to evaluate the main materials used for the packaging of high power light-emitting diodes (LEDs), i.e., the die attach materials, the encapsulant materials, and high color rendering index(CRI) sol-gel composite materials. All of these materials had been discussed the performance, reliability, and issues in high power LED packages. High power white LEDs are created either from blue or near-ultraviolet chips encapsulated with a yellow phosphor, or from red-green-blue LED light mixing systems. The phosphor excited by blue LED chip was mostly used in experiment of this dissertation. The die attach materials contains filler particles possessing a maximum particle size less than 1.5 mum in diameter blended with epoxy polymer matrix. Such compositions enable thin bond line thickness, which decreases thermal resistance that exists between thermal interface materials and the corresponding mating surfaces. The thermal conductivity of nano silver die attach materials is relatively low, the thermal resistance from the junction to board is just 1.6 KW-1 in the bond line thickness of 5.3 mum, which is much lower than the thermal resistance using conventional die attach materials. The silicone die attach adhesive made in the lab cures through the free radical reaction of epoxy-functional organopolysiloxane and through the hydrosilylation reaction between alkenyl-functional organopolysiloxane and silicone-boned hydrogen-functional organopolysiloxane. By the combination of the free radical reaction and the hydrosilylation reaction, the low-molecular-weight silicone oil will not be out-migrated and not contaminate wire bondability to the LED chip and lead frame. Hence, the silicone die attach adhesive made in the lab can pass all reliability tests, such as operating life test JEDEC 85°C/85RH and room temperature operating life test. For LED encapsulating materials, most of commercial silicone encapsulants still suffer thermal/radiation induced

  9. PLASTICITY OF SELECTED METALLIC MATERIALS IN DYNAMIC DEFORMATION CONDITIONS

    Directory of Open Access Journals (Sweden)

    Jacek PAWLICKI

    2014-06-01

    Full Text Available Characteristics of a modernized flywheel machine has been presented in the paper. The laboratory stand enables to perform dynamic tensile tests and impact bending with a linear velocity of the enforcing element in the range of 5÷40 m/s. A new data acquisition system, based on the tensometric sensors, allows for significant qualitative improvement of registered signals. Some preliminary dynamic forming tests were performed for the selected group of metallic materials. Subsequent microstructural examinations and identification of the fracture type enabled to describe a correlation between strain rate, strain and microstructure.

  10. Theoretical Development of an Orthotropic Elasto-Plastic Generalized Composite Material Model

    Science.gov (United States)

    Goldberg, Robert K.; Carney, Kelly S.; DuBois, Paul; Hoffarth, Canio; Harrington, Joseph; Subramanian, Rajan; Blankenhorn, Gunther

    2014-01-01

    The need for accurate material models to simulate the deformation, damage and failure of polymer matrix composites is becoming critical as these materials are gaining increased usage in the aerospace and automotive industries. While there are several composite material models currently available within LS-DYNA (Registered), there are several features that have been identified that could improve the predictive capability of a composite model. To address these needs, a combined plasticity and damage model suitable for use with both solid and shell elements is being developed and is being implemented into LS-DYNA as MAT_213. A key feature of the improved material model is the use of tabulated stress-strain data in a variety of coordinate directions to fully define the stress-strain response of the material. To date, the model development efforts have focused on creating the plasticity portion of the model. The Tsai-Wu composite failure model has been generalized and extended to a strain-hardening based orthotropic material model with a non-associative flow rule. The coefficients of the yield function, and the stresses to be used in both the yield function and the flow rule, are computed based on the input stress-strain curves using the effective plastic strain as the tracking variable. The coefficients in the flow rule are computed based on the obtained stress-strain data. The developed material model is suitable for implementation within LS-DYNA for use in analyzing the nonlinear response of polymer composites.

  11. Study on Impact Acoustic—Visual Sensor-Based Sorting of ELV Plastic Materials

    Science.gov (United States)

    Huang, Jiu; Tian, Chuyuan; Ren, Jingwei; Bian, Zhengfu

    2017-01-01

    This paper concentrates on a study of a novel multi-sensor aided method by using acoustic and visual sensors for detection, recognition and separation of End-of Life vehicles’ (ELVs) plastic materials, in order to optimize the recycling rate of automotive shredder residues (ASRs). Sensor-based sorting technologies have been utilized for material recycling for the last two decades. One of the problems still remaining results from black and dark dyed plastics which are very difficult to recognize using visual sensors. In this paper a new multi-sensor technology for black plastic recognition and sorting by using impact resonant acoustic emissions (AEs) and laser triangulation scanning was introduced. A pilot sorting system which consists of a 3-dimensional visual sensor and an acoustic sensor was also established; two kinds commonly used vehicle plastics, polypropylene (PP) and acrylonitrile-butadiene-styrene (ABS) and two kinds of modified vehicle plastics, polypropylene/ethylene-propylene-diene-monomer (PP-EPDM) and acrylonitrile-butadiene-styrene/polycarbonate (ABS-PC) were tested. In this study the geometrical features of tested plastic scraps were measured by the visual sensor, and their corresponding impact acoustic emission (AE) signals were acquired by the acoustic sensor. The signal processing and feature extraction of visual data as well as acoustic signals were realized by virtual instruments. Impact acoustic features were recognized by using FFT based power spectral density analysis. The results shows that the characteristics of the tested PP and ABS plastics were totally different, but similar to their respective modified materials. The probability of scrap material recognition rate, i.e., the theoretical sorting efficiency between PP and PP-EPDM, could reach about 50%, and between ABS and ABS-PC it could reach about 75% with diameters ranging from 14 mm to 23 mm, and with exclusion of abnormal impacts, the actual separation rates were 39.2% for PP, 41

  12. PARAMETRIC VARIATIONAL PRINCIPLE BASED ELASTIC-PLASTIC ANALYSIS OF HETEROGENEOUS MATERIALS WITH VORONOI FINITE ELEMENT METHOD

    Institute of Scientific and Technical Information of China (English)

    ZHANG Hong-wu; WANG Hui

    2006-01-01

    The Voronoi cell finite element method (VCFEM) is adopted to overcome the limitations of the classic displacement based finite element method in the numerical simulation of heterogeneous materials. The parametric variational principle and quadratic programming method are developed for elastic-plastic Voronoi finite element analysis of two-dimensional problems. Finite element formulations are derived and a standard quadratic programming model is deduced from the elastic-plastic equations. Influence of microscopic heterogeneities on the overall mechanical response of heterogeneous materials is studied in detail. The overall properties of heterogeneous materials depend mostly on the size, shape and distribution of the material phases of the microstructure. Numerical examples are presented to demonstrate the validity and effectiveness of the method developed.

  13. Plastic phase change material and articles made therefrom

    Science.gov (United States)

    Abhari, Ramin

    2016-04-19

    The present invention generally relates to a method for manufacturing phase change material (PCM) pellets. The method includes providing a melt composition, including paraffin and a polymer. The paraffin has a melt point of between about 10.degree. C. and about 50.degree. C., and more preferably between about 18.degree. C. and about 28.degree. C. In one embodiment, the melt composition includes various additives, such as a flame retardant. The method further includes forming the melt composition into PCM pellets. The method further may include the step of cooling the melt to increase the melt viscosity before pelletizing. Further, PCM compounds are provided having an organic PCM and a polymer. Methods are provided to convert the PCM compounds into various form-stable PCMs. A method of coating the PCMs is included to provide PCMs with substantially no paraffin seepage and with ignition resistance properties.

  14. Plastic phase change material and articles made therefrom

    Energy Technology Data Exchange (ETDEWEB)

    Abhari, Ramin

    2016-04-19

    The present invention generally relates to a method for manufacturing phase change material (PCM) pellets. The method includes providing a melt composition, including paraffin and a polymer. The paraffin has a melt point of between about 10.degree. C. and about 50.degree. C., and more preferably between about 18.degree. C. and about 28.degree. C. In one embodiment, the melt composition includes various additives, such as a flame retardant. The method further includes forming the melt composition into PCM pellets. The method further may include the step of cooling the melt to increase the melt viscosity before pelletizing. Further, PCM compounds are provided having an organic PCM and a polymer. Methods are provided to convert the PCM compounds into various form-stable PCMs. A method of coating the PCMs is included to provide PCMs with substantially no paraffin seepage and with ignition resistance properties.

  15. Characterization of a new plastic scintillation material and comparison with liquid BC-501A scintillator

    OpenAIRE

    Poleshchuk, Oleksii

    2015-01-01

    In this work the capability of various scintillation materials to discriminate gamma rays and neutrons were studied. Also such basic properties of scintillators as light emission spectrum and light output were determined. The studied materials were BC-501A liquid scintillator and a plastic scintillator provided by CEA. An experimental setup consisting of detector shielding, analog and digital electronics and data acquisition system was built to study the neutron-gamma discrimination propertie...

  16. Fracture mechanics based design for radioactive material transport packagings -- Historical review

    Energy Technology Data Exchange (ETDEWEB)

    Smith, J.A.; Salzbrenner, D.; Sorenson, K.; McConnell, P.

    1998-04-01

    The use of a fracture mechanics based design for the radioactive material transport (RAM) packagings has been the subject of extensive research for more than a decade. Sandia National Laboratories (SNL) has played an important role in the research and development of the application of this technology. Ductile iron has been internationally accepted as an exemplary material for the demonstration of a fracture mechanics based method of RAM packaging design and therefore is the subject of a large portion of the research discussed in this report. SNL`s extensive research and development program, funded primarily by the U. S. Department of Energy`s Office of Transportation, Energy Management and Analytical Services (EM-76) and in an auxiliary capacity, the office of Civilian Radioactive Waste Management, is summarized in this document along with a summary of the research conducted at other institutions throughout the world. In addition to the research and development work, code and standards development and regulatory positions are also discussed.

  17. 国内外可食性与全降解食品包装材料发展现状与趋势%Global Development Status and Trend of Edible and Biodegradable Food Packaging Materials

    Institute of Scientific and Technical Information of China (English)

    侯汉学; 董海洲; 王兆升; 代养勇

    2011-01-01

    Food packaging is one of the most important parts in packaging industry, which leads to increasingly serious environment pollution. This paper reviewed the global development status and trend of edible and biodegradable food packaging materials. It analyzed the social problems resulted from petrochemical-based plastic packaging and research status and trend in developing biodegradable food packing materials. It also pointed out the necessity and urgency for energetically developing full biodegradable food packaging materials.%食品包装业是包装工业的重要组成部分,它带来的环境污染问题也日益严重.本文就国内外可食性与全降解食品包装材料的研发与生产现状进行了综述.分析了石油基塑料包装带来的社会问题和国内外全降解食品包装材料研发现状与趋势,指出了大力发展全降解食品包装材料的必要性和紧迫性.

  18. Prediction and classification of the degradation state of plastic materials used in modern and contemporary art

    Science.gov (United States)

    Manfredi, M.; Barberis, E.; Marengo, E.

    2017-01-01

    Today, artworks partially or completely made of plastic materials can be found in almost all international museums and collections. The deterioration of these objects is now becoming evident mainly because these synthetic materials are not designed for a long life and the characterization of their state of conservation can help curators and conservators. In this research we investigated the applicability of a portable attenuated total reflection (ATR) infrared spectrometer for the non-invasive characterization and for monitoring the degradation of plastics used in modern and contemporary art. Several polypropylene and polycarbonate samples were artificially aged in solar box, simulating about 200 years of museum light exposure, and they were monitored with the portable ATR, creating an infrared library of the conservation state of plastics. Through the use of chemometric techniques like principal component analysis-linear discriminant analysis and partial least square—discriminant analysis, we built a robust degradation model of each material that can be used to predict and classify the degradation state of artworks and to identify the priority of intervention in the museum collections. Portable ATR coupled to multivariate statistics can be employed for taking care of plastic artworks as it is non-invasive, the analysis is very fast and it can be performed directly in situ.

  19. Waste Materials from Tetra Pak Packages as Reinforcement of Polymer Concrete

    Directory of Open Access Journals (Sweden)

    Miguel Martínez-López

    2015-01-01

    Full Text Available Different concentrations (from 1 to 6 wt% and sizes (0.85, 1.40, and 2.36 mm of waste Tetra Pak particles replaced partially silica sand in polymer concrete. As is well known, Tetra Pak packages are made up of three raw materials: cellulose (75%, low density polyethylene (20%, and aluminum (5%. The polymer concrete specimens were elaborated with unsaturated polyester resin (20% and silica sand (80% and irradiated by using gamma rays at 100 and 200 kGy. The obtained results have shown that compressive and flexural strength and modulus of elasticity decrease gradually, when either Tetra Pak particle concentration or particle size is increased, as regularly occurs in composite materials. Nevertheless, improvements of 14% on both compressive strength and flexural strength as well as 5% for modulus of elasticity were obtained when polymer concrete is irradiated.

  20. Directory of Certificates of Compliance for radioactive materials packages: Report of NRC approved quality assurance programs for radioactive materials packages. Volume 3, Revision 15

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-10-01

    The purpose of this directory is to make available a convenient source of information on packagings which have been approved by the US Nuclear Regulatory Commission. To assist in identifying packaging, an index by Model Number and corresponding Certificate of Compliance Number is included at the front of Volumes 1 and 2. An alphabetical listing by user name is included in the back of Volume 3 of approved QA programs. The reports include a listing of all users of each package design and approved QA programs prior to the publication date.

  1. On the Parasitic Mass of Launch Packages for Electromagnetic Guns

    Science.gov (United States)

    2001-04-26

    reduced by changing to a ’double-ramp’ configuration 2, by using high strength rod materials, or by using lightweight sabots. A fibre reinforced plastic (FRP...value of L/Lo = 4, the use of a fibre reinforced plastic for the sabot instead of aluminium alloy reduces the PMR by 0.24 for a tungsten alloy...of the packages feature fibre reinforced plastic sabots; the remainder using high strength aluminium alloy. The high specific strength and stiffness

  2. Use of ceramic materials in waste-package systems for geologic disposal of nuclear wastes

    Energy Technology Data Exchange (ETDEWEB)

    Fullam, H.T.

    1980-12-01

    A study to investigate the potential use of ceramic materials as components in the waste package systems was conducted. The initial objective of the study was to screen and compare a large number of ceramic materials and identify the best materials for the proposed application. The principal method used to screen the candidates was to subject samples of each material to a series of leaching tests and to determine their relative resistance to attack by the leach solutions. A total of 14 ceramic materials, plus graphite and basalt were evaluated using three different leach solutions: demineralized water, a synthetic Hanford ground water, and a synthetic WIPP brine solution. The ceramic materials screened were Al/sub 2/O/sub 3/ (99%), Al/sub 2/O/sub 3/ (99.8%), mullite (2Al/sub 2/O/sub 3/.SiO/sub 2/), vitreous silica (SiO/sub 2/), BaTiO/sub 3/, CaTiO/sub 3/, CaTiSiO/sub 5/, TiO/sub 2/, ZrO/sub 2/, ZrSiO/sub 4/, Pyroceram 9617, and Marcor Code 9658 machinable glass-ceramic. Average leach rates for the materials tested were determined from analyses of the leach solutions and/or sample weight loss measurements. Because of the limited scope of the present study, evaluation of the specimens was limited to ceramographic examination. Based on an overall evaluation of the leach rate data, five of the materials tested, namely graphite, TiO/sub 2/, ZrO/sub 2/, and the two grades of alumina, exhibited much greater resistance to leaching than did the other materials tested. Based on all the experimental data obtained, and considering other factors such as cost, availability, fabrication technology, and mechanical and physical properties, graphite and alumina are the preferred candidates for the barrier application. The secondary choices are TiO/sub 2/ and ZrO/sub 2/.

  3. Effect of plastic deformation on the acoustoelastic response of some materials

    Science.gov (United States)

    Daami, T.; Touratier, M.; Castex, L.

    1987-12-01

    Acoustoelastic birefringence is measured with the acoustic polarimeter by transmitting ultrasonic shear waves at two perpendicular polarizations through the thickness of several uniaxial test specimens. The results are available for the following materials: SAE 1010 and SAE 4118 steel, pure titanium, 2024 aluminum and 60-40 brass, but are only presented here for SAE 4118 steel and pure titanium. The uniaxial test specimens have been subjected to plastic deformation followed by complete unloading. It is shown that the assumption that the plastic flow leading to the residual-stress state does not change the acoustic response of the material, does not hold for all materials and that further characterization development is required for general quantitative residual-stress determination.

  4. The use of plasticizing additives based on recycled raw materials in the petrochemical rubber mixtures

    Directory of Open Access Journals (Sweden)

    Z. S. Shashok

    2016-01-01

    Full Text Available At present, the development of alternative products for elastomers based on recycling petrochemical raw materials is a new trend of the rubber industry progress. Petrochemical raw materials include spent lubricants and motor oils are among such recycling products. In this context, the influence of the products of recycling waste engine oil (DVCH and RA in comparison with industrial oil (I-20 on the technological properties of filled elastomeric compositions was investigated. The elastomeric compositions were based on poly isoprene and divinyl rubbers. The plasticizing components were manufactured by IOOO “DVCH-Menedzhment”. They are mixture of hydro-carbons, C16–C20 and differ from each other in the content of linear and branched paraffin. Plastic-elastic properties of rubber compounds on the shear disk viscometer MV2000 in accordance with GOST 10722–76 was carried out. Kinetics of vulcanization on the rheometer ODR2000 according to GOST 12535–84 was defined. It is shown that the introduction of RA test plasticizing component provides a significant effect on Mooney viscosity, as compared to elastomeric compositions containing a plasticizer and I-20 and plasticizing additive DVCH. It revealed that the administration of all components in the studied plasticizing elastomer compositions based on a combination poly isoprene and divinyl rubbers has no significant effect on the rate of relaxation of stress of rubber compounds. It is found that elastomeric compositions containing as additives investigated processing waste oil products (DVCH and RA are characterized by a slightly smaller value of time to reach an optimal degree of vulcanization.

  5. Natural biopolimers in organic food packaging

    Science.gov (United States)

    Wieczynska, Justyna; Cavoski, Ivana; Chami, Ziad Al; Mondelli, Donato; Di Donato, Paola; Di Terlizzi, Biagio

    2014-05-01

    Concerns on environmental and waste problems caused by use of non-biodegradable and non-renewable based plastic packaging have caused an increase interest in developing biodegradable packaging using renewable natural biopolymers. Recently, different types of biopolymers like starch, cellulose, chitosan, casein, whey protein, collagen, egg white, soybean protein, corn zein, gelatin and wheat gluten have attracted considerable attention as potential food packaging materials. Recyclable or biodegradable packaging material in organic processing standards is preferable where possible but specific principles of packaging are not precisely defined and standards have to be assessed. There is evidence that consumers of organic products have specific expectations not only with respect to quality characteristics of processed food but also in social and environmental aspects of food production. Growing consumer sophistication is leading to a proliferation in food eco-label like carbon footprint. Biopolymers based packaging for organic products can help to create a green industry. Moreover, biopolymers can be appropriate materials for the development of an active surfaces designed to deliver incorporated natural antimicrobials into environment surrounding packaged food. Active packaging is an innovative mode of packaging in which the product and the environment interact to prolong shelf life or enhance safety or sensory properties, while maintaining the quality of the product. The work will discuss the various techniques that have been used for development of an active antimicrobial biodegradable packaging materials focusing on a recent findings in research studies. With the current focus on exploring a new generation of biopolymer-based food packaging materials with possible applications in organic food packaging. Keywords: organic food, active packaging, biopolymers , green technology

  6. Biodegradable packaging for storage of fruit and other horticultural products: materials, properties and its effect on fruit quality

    Directory of Open Access Journals (Sweden)

    Iva Tokić

    2011-07-01

    Full Text Available The role of packaging material is to preserve the nutritional and sensory properties of product, inform consumers about the nutritional values, facilitate storage and handling. Today, the development and commercial production of biodegradable packaging materials, other than paper, is focused on materials from other renewable sources of plant origin. Further development of biodegradable polymer market is dependent on securing a permanent, reliable and cheap sources of raw materials. In the battle for their share of the market, biopolymers enjoy strong support from policy and legislation, particularly in Europe. Attractive and efficient packaging contribute to the development of new products, provides an interesting presentation to consumers, lowers production costs, improves the food product and defines the specific ‘’brand’’.

  7. Microbial control by packaging: a review.

    Science.gov (United States)

    Cutter, Catherine Nettles

    2002-03-01

    Since early man first used a variety of natural containers to store and eat foods, significant developments in food packaging materials have provided the means to suppress microbial growth as well as protect foods from external microbial contamination. Throughout this progression, packaging materials have been developed specifically to prevent the deterioration of foods resulting from exposure to air, moisture, or pH changes associated with the food or the surrounding atmosphere. Both flexible and rigid packaging materials, alone or in combination with other preservation methods, have been developed to offer the necessary barrier, inactivation, and containment properties required for successful food packaging. Examples of flexible packaging used to inactivate microorganisms associated with foods include controlled atmosphere, vacuum, modified atmosphere, active, and edible packaging. Additionally, the combination of rigid packaging materials made from metal, glass, or plastic with heat provides the most effective and widely used method for inactivating microorganisms. As with all food products, it is necessary to integrate a HACCP-based program to assure quality throughout the packaging operation. In addition to packaging improvements, other novel technologies include the development of detectors for oxygen levels, bacterial toxins, and microbial growth, or the integration of time-temperature indicators for detection of improper handling or storage.

  8. Corrosion resistance of plastic materials and method for improvement on quality. Plastic zairyo no taishokusei to hinshitsu kojo taisaku

    Energy Technology Data Exchange (ETDEWEB)

    Li, W. (Tokyo Institute of Technology, Tokyo (Japan). Faculty of Engineering)

    1991-09-20

    The plastic materials are described mainly in corrosiveness as follows: Definition of corrosion for the high-molecular materials. Obtainment of stress relaxation curve, by utilizing the photoelasticity, of the polyvinyl chloride resin to be evaluated in corrosiveness. Corrosion morphology (observation result by the optical microscope) in case that the PP (polypropylene resin) reformed by SBS (styrene butadiene styrene) is corroded by HNO{sub 3} or H{sub 2}SO{sub 4}, and chemical reaction to mainly cause that corrosion. Utilization of differential scanning calorimetry to set the PP and that reformed by NBR (nitrile butadiene rubber) in welding temperature. Dyeing of NBR-reformed phenol resin by OsO{sub 4} and observation on the thus dyed structure (where there exist both the contents). Observational investigation, by applying the AE (acoustic emission) technology, on the heightening in toughness due to reforming the phenol resin by NBR and degradation due to the corrosion of NBR-reformed phenol resin. 10 refs., 15 figs.

  9. Contrasting glass and plastic material requirements for reflective and refractive CPV solar systems

    Science.gov (United States)

    Horne, Steve; Krevor, David

    2012-10-01

    Concentrator PhotoVoltaic (CPV) solar energy systems concentrate the sun 500 - 1,000 times or more, in order to take economic advantage of the most advanced and efficient solar cells. The two prevalent system architectures use either reflective glass optics - such as based on a Cassegrain telescope design - or a refractive plastic system - either an acrylic or silicone-on-glass Fresnel lens - for concentration. Both systems have their advantages in areas of performance and durability. Both system designs manufacture their optics by low-cost processes that are unavailable to the other material system. These contrasts are reviewed. The refractive system embodies a simpler optical concept, requiring a single Fresnel lens rather than two concentrating mirrors. However, the reflective, glass system uses the greater design sophistication to provide a greater acceptance angle, which yields tolerance benefits in both manufacture and installation; and also provides faster optics without suffering the spectral aberrations of the refractive systems. Both glass and plastics are low-cost commodity materials. The long-term durability of optical glass is more firmly established than for optical plastics. And light transmission through optical plastics is attenuated by absorbance in both the UV and IR regions, in regions where such light is harvested by efficient multi-junction solar cells.

  10. A numerical model for the thermo-elasto-plastic behaviour of a material

    Science.gov (United States)

    Ray, Sujit K.; Utki, Senol

    1989-01-01

    This paper presents a numerical model for the thermo-elasto-plastic behavior of an isotropic material. The model is based on the assumption that the yielding of the material obeys von Mises distortion energy theory and the material exhibits isotropic strain hardening. This unique model can be used both for isothermal and non-isothermal cases. The original formulation for the non-isothermal three-dimensional case has been specialized for plane stress conditions and the equations for the computation of warping and thickness change are provided. The finite element implementation of this model is also outlined.

  11. Energy and raw material saving through recycling of plastics materials extracted from urban waste. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Michaux, J.

    The study is divided into 3 parts: Technical feasibility study, economic feasibility study, study of a factory handling 2,400 tons/year of plastics waste, and technico-economic feasibility study and market research, with an analysis of energy savings.

  12. Antimicrobial Performance of Two Different Packaging Materials on the Microbiological Quality of Fresh Salmon

    Directory of Open Access Journals (Sweden)

    Manuela Rollini

    2016-01-01

    Full Text Available In the present research the antimicrobial activity of two active packaging materials on the spoilage microbiota of fresh salmon fillets was tested. A PET-coated film (PET: Polyethylene Terephthalate containing lysozyme and lactoferrin was tested in parallel with a carvacrol-coextruded multilayer film. Salmon fillet samples were stored up to four days at 0 and 5 °C, comparatively. The carvacrol multilayer film was found effective in preventing mesophiles and psychrotrophs at shorter storage time and at lower temperature (4.0 compared to 5.0 log CFU/g in the control sample—CFU: Colony Forming Units. Lysozyme/lactoferrin-coated PET was instead efficient in decreasing H2S-producing bacteria at longer storage time and higher temperature (2.7 instead of 4.7 log CFU/g in the control sample. Even if is not intended as a way to “clean” a contaminated food product, an active package solution can indeed contribute to reducing the microbial population in food items, thus lowering the risk of food-related diseases.

  13. 包装材料对鲜切菠萝保鲜效果的影响%Fresh-keeping effects of packaging materials on fresh-cut pineapple

    Institute of Scientific and Technical Information of China (English)

    覃海元; 潘嫣丽; 黄雪明; 黎朝惠

    2011-01-01

    The fresh-keeping effect of different kinds of packaging materials on fresh-cut pineapple was studied. Pineapple were chosen,peeled and cut to wedges(1. 5~2. 0cm chick). Dipped in 0. 5% citric acid solution for 3min,the pineapple wedges were packaged in plastic trays and covered with polyethylene(PE)film,high-density polyethylene(HDPE)bags and polyethylene-polypropylene(PE/PP)composite bags respectively,or packaged in polyester(PET)cup and covered with a PET top having a 3mm diameter hole,and then stored at 5℃ for 10 days. The fresh-cut pineapples were measured at 0,2,4,6,8,10 day respectively. The results showed that PE/PP and PET packaging materials with low gas-permeability could reduce weight loss,browning,juice leakage,electrolyte leakage and dehydroascorbic acid loss more than PE and HDPE films did,but all the packaging materials did almost the same effects on the acid and TSS contents.%研究不同包装材料对鲜切菠萝的保鲜效果。菠萝经挑选、去皮后切成1.5~2.0cm厚的切片,用0.5%柠檬酸溶液浸泡护色3min后,放入塑料托盘中,分别用PE保鲜膜、HDPE保鲜袋和PE/PP复合袋包裹,或放入PET保鲜盒中并用带有1个直径3mm的盖封口,放入5℃的冰柜里冷藏10d;当天和每2d检测1次样品。结果表明,透气性差的PE/PP袋和PET盒较PE膜和HDPE袋更有利于减少鲜切菠萝的失重、褐变、渗汁、相对电导率增加和还原型抗坏血酸损失,但不同包装材料对总酸和可溶性固形物含量的影响不大。

  14. Investigation of metallic, ceramic, and polymeric materials for engineered barrier applications in nuclear-waste packages

    Energy Technology Data Exchange (ETDEWEB)

    Westerman, R.E.

    1980-10-01

    An effort to develop licensable engineered barrier systems for the long-term (about 1000 yr) containment of nuclear wastes under conditions of deep continental geologic disposal has been underway at Pacific Northwest Laboratory since January 1979, under the auspices of the High-Level Waste Immobilization Program. In the present work, the barrier system comprises the hard or structural elements of the package: the canister, the overpack(s), and the hole sleeve. A number of candidate metallic, ceramic, and polymeric materials were put through mechanical, corrosion, and leaching screening tests to determine their potential usefulness in barrier-system applications. Materials demonstrating adequate properties in the screening tests will be subjected to more detailed property tests, and, eventually, cost/benefit analyses, to determine their ultimate applicability to barrier-system design concepts. The following materials were investigated: two titanium alloys of Grade 2 and Grade 12; 300 and 400 series stainless steels, Inconels, Hastelloy C-276, titanium, Zircoloy, copper-nickel alloys and cast irons; total of 14 ceramic materials, including two grades of alumina, plus graphite and basalt; and polymers such as polyamide-imide, polyarylene, polyimide, polyolefin, polyphenylene sulfide, polysulfone, fluoropolymer, epoxy, furan, silicone, and ethylene-propylene terpolymer (EPDM) rubber. The most promising candidates for further study and potential use in engineered barrier systems were found to be rubber, filled polyphenylene sulfide, fluoropolymer, and furan derivatives.

  15. 储存条件对塑料瓶装大豆油中塑化剂含量影响的研究%Influence of storage condition on the contents of plasticizers in soybean oil packaged in plastic bottle

    Institute of Scientific and Technical Information of China (English)

    刘玉兰; 张明明; 朱远坤; 杨书平

    2015-01-01

    The fresh soybean oils were stored respectively in PET plastic bottle and PE plastic bottle, and the influences of storage temperature, storage time and light on the contents of plasticizers in the soybean oil were investigated. The results showed that the contents of DBP and DEHP in soybean oils packaged in PE plastic bottle were obviously higher than those in PET plastic bottle when the storage temperature was above 27℃ and storage time was 20 d. The contents of DPP in soybean oils had no change when the tem-perature didn’t exceed 50℃, while it rose significantly when the temperature was above 50℃. Further-more, when stored at 65℃ for 90 d, the contents of DPP in the soybean oils packaged in PET and PE plastic bottles were up to 1 559. 3 μg/kg and 2 756. 8 μg/kg, respectively. In addition, when stored at 65℃ for 50 d, DMP could be detected in soybean oil packaged in PE plastic bottle, and its contents were 43. 7(50 d),128. 7(70 d),114. 3 μg/kg(90 d). When stored at 50℃ for 90 d, the content of DBP in soybean oil packaged in PE plastic bottle reached 452. 0μg/kg, 1. 5 times as high as the national standard limit for DBP. Compared with the lucifuge storage, light had no influence on DPP and small im-pacts on DBP and DEHP for a short time. Under the same storage temperature and light condition, as storage time prolonging, the content of DBP in soybean oils packaged in PET and PE plastic bottles were on a rise, and the content of DEHP presented a fluctuation trend.%以新鲜大豆油为原料,将其分别盛装于PET材质塑料瓶和PE材质塑料瓶中,研究不同储存温度、储存时间以及光照对大豆油中邻苯二甲酸酯类塑化剂含量变化的影响。结果表明:储存20 d且储存温度高于27℃时PE瓶装大豆油中DBP和DEHP含量明显高于PET瓶装大豆油的;大豆油中DPP含量在储存温度不超过50℃时基本无变化,但储存温度高于50℃时,其含量明显增加。65℃储存90 d后,PET、PE瓶

  16. Water equivalence of some plastic-water phantom materials for clinical proton beam dosimetry

    Energy Technology Data Exchange (ETDEWEB)

    Al-Sulaiti, L., E-mail: l.al-sulaiti@surrey.ac.uk [Physics Department, University of Surrey, Guildford (United Kingdom); Radiation Dosimetry Team, National Physical Laboratory, Teddington (United Kingdom); Shipley, D.; Thomas, R. [Radiation Dosimetry Team, National Physical Laboratory, Teddington (United Kingdom); Owen, P. [Physics Department, University of Surrey, Guildford (United Kingdom); Radiation Dosimetry Team, National Physical Laboratory, Teddington (United Kingdom); Kacperek, A. [Douglas Cyclotron, Clatterbridge Centre for Oncology, Wirral (United Kingdom); Regan, P.H. [Physics Department, University of Surrey, Guildford (United Kingdom); Palmans, H. [Radiation Dosimetry Team, National Physical Laboratory, Teddington (United Kingdom)

    2012-07-15

    Plastic-water phantom materials are not exactly water equivalent since they have a different elemental composition and different interaction cross sections for protons than water. Several studies of the water equivalence of plastic-water phantom materials have been reported for photon and electron beams, but none for clinical proton beams. In proton beams, the difference between non-elastic nuclear interactions in plastic-water phantom materials compared to those in water should be considered. In this work, the water equivalence of Plastic Water{sup Registered-Sign} (PW){sup 1}, Plastic Water{sup Registered-Sign} Diagnostic Therapy (PWDT){sup 1} and solid water (WT1){sup 2} phantoms was studied for clinical proton energies of 60 MeV and 200 MeV. This was done by evaluating the fluence correction factor at equivalent depths; first with respect to water and then with respect to graphite by experiment and Monte Carlo (MC) simulations using FLUKA. MC simulations showed that the fluence correction with respect to water was less than 0.5% up to the entire penetration depth of the protons at 60 MeV and less than 1% at 200 MeV up to 20 cm depth for PWDT, PW and WT1. With respect to graphite the fluence correction was about 0.5% for 60 MeV and about 4% for 200 MeV. The experimental results for modulated and un-modulated 60 MeV proton beams showed good agreement with the MC simulated fluence correction factors with respect to graphite deviating less than 1% from unity for the three plastic-water phantoms. - Highlights: Black-Right-Pointing-Pointer We study plastic-water in clinical proton beams by experiment and Monte Carlo. Black-Right-Pointing-Pointer We obtain fluence correction factors for water and graphite. Black-Right-Pointing-Pointer The correction factor for water was close to 1 at 60 MeV and <0.990 at 200 MeV. Black-Right-Pointing-Pointer The correction factor for graphite was {approx}0.5% at 60 MeV and up to 4% at 200 MeV.

  17. Feasibility Study of Sensor Aided Impact Acoustic Sorting of Plastic Materials from End-of-Life Vehicles (ELVs)

    OpenAIRE

    Jiu Huang; Zhengfu Bian; Shaogang Lei

    2015-01-01

    The purpose of this feasibility research was to study a novel sensor based separation method for recycling of plastic materials from end-of-life vehicles (ELVs) by using eigen-frequency response of impact acoustic emission. In this research three kinds of commonly used plastics, polypropylene (PP), acrylonitrile-butadiene-styrene (ABS), and styrene-maleic-anhydride (SMA) sampled from end-of-life vehicles, were researched. Almost all the crushed plastic scraps had a flake structure, theoretica...

  18. Earthquake statistics inferred from plastic events in soft-glassy materials

    CERN Document Server

    Benzi, Roberto; Trampert, Jeannot

    2016-01-01

    We propose a new approach for generating synthetic earthquake catalogues based on the physics of soft glasses. The continuum approach produces yield-stress materials based on Lattice-Boltzmann simulations. We show that, if the material is stimulated below yield stress, plastic events occur, which have strong similarities with seismic events. Based on a suitable definition of displacement in the continuum, we show that the plastic events obey a Gutenberg-Richter law with exponents similar to those for real earthquakes. We further find that average acceleration, energy release, stress drop and recurrence times scale with the same exponent. The approach is fully self-consistent and all quantities can be calculated at all scales without the need of ad hoc friction or statistical laws. We therefore suggest that our approach may lead to new insight into understanding of the physics connecting the micro and macro scale of earthquakes.

  19. Guidelines for conducting impact tests on shipping packages for radioactive material

    Energy Technology Data Exchange (ETDEWEB)

    Mok, G.C.; Carlson, R.W.; Lu, S.C.; Fischer, L.E.

    1995-09-01

    Federal regulation (10 CFR Part 71) specifies a number of impact conditions (free-drop, penetration, and puncture), under which a package for the transport of radioactive materials must be tested or evaluated to demonstrate compliance with the regulation. This report is a comprehensive guide to the planning and execution of these impact tests. The report identifies the required considerations for both the design, pre-, and post-test inspections of the test model and the measurement, recording, analysis, and reporting of the test data. The report also presents reasons for the requirements, identifies the major difficulties in meeting these requirements, and suggests possible methods to overcome the difficulties. Discussed in substantial detail is the use of scale models and instrumented measurements.

  20. Eggshell and Bacterial Cellulose Composite Membrane as Absorbent Material in Active Packaging

    Directory of Open Access Journals (Sweden)

    S. Ummartyotin

    2016-01-01

    Full Text Available Bacterial cellulose and eggshell composite was successfully developed. Eggshell was mixed with bacterial cellulose suspension and it was casted as a composite film. CaCO3 derived from eggshell was compared with its commercial availability. It can be noted that good dispersion of eggshell particle was prepared. Eggshell particle was irregular in shape with a variation in size. It existed in bacterial cellulose network. Characterization on composite was focused on thermal and mechanical properties. It showed that flexibility and thermal stability of composite were enhanced. No significant effect of mechanical properties was therefore observed. The thermal stability of composite was stable up to 300°C. The adsorption experiment on water and vegetable oil capacity was performed. The enhancement on adsorption was due to the existence of eggshell in bacterial cellulose composite. It exhibited the potential to be a good candidate for absorbent material in active packaging.

  1. Hydrophobic and breathable nanomembrane for food package material by mimicking cocoon’s structure

    Directory of Open Access Journals (Sweden)

    Zhang Zhen

    2015-01-01

    Full Text Available The aim of this study was to investigate the cross-linked poly(vinyl alcohol nanofibrous mats treated by flourinated alkane in supercritical carbon dioxide medium. The surface morphology and chemical structure of electrospun mats were analyzed by scanning electron microscopy and Fourier transform infrared. The results showed that the treated mats could maintain their integrity and fibrous morphology as well as their porous structure after being treated. However, the wettability was changed greatly, the average contact angle of treated nanofibrous mats increased from its original value of 28° to 134°, revealing that the treated mats had good water repellent properties. The paper concluded that the hydrophobic and breathable mats with porous structure might be an excellent candidate for food package materials.

  2. Electronic packaging materials prepared by powder injecting molding and pressure infiltration process

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    AlSiCp (65 vol.% SiC) electronic packaging materials were manufactured by powder injection molding (PIM) and pressure infiltration process in order to obtain near net-shaped parts. SiCp preformed compacts obtained by pre-sintering process at 1150 K have high strength and good appearance, and the ratio of open porosity to total porosiry is nearly 98%. The relative density of composites is bigger than 99%. The thermal conductivity of AlSiCp composites fabricated by this method is 198 W·m-1·K-1, and the coefficient of thermal expansion (CTE) is 8.0 × 10-6/K (298 K).

  3. Utilization of biobased polymers in food packaging: Assessment of materials, production and commercialization

    Science.gov (United States)

    Food packaging contains and protects food, keeps it safe and secure, retains food quality and freshness, and increases shelf-life of food. Packaging should be affordable and biodegradable. Packaging is the core of the businesses of fast-foods, ready meals, on-the-go beverages, snacks and manufacture...

  4. FIFTH STATUS REPORT: TESTING OF AGED SOFTWOOD FIBERBOARD MATERIAL FOR THE 9975 SHIPPING PACKAGE

    Energy Technology Data Exchange (ETDEWEB)

    Daugherty, W.; Skidmore, E.; Dunn, K.

    2014-04-15

    Samples have been prepared from a 9975 lower fiberboard subassembly fabricated from softwood fiberboard. Physical, mechanical and thermal properties have been measured following varying periods of conditioning in each of several environments. These tests have been conducted in the same manner as previous testing on cane fiberboard samples. Overall, similar aging trends are observed for softwood and cane fiberboard samples, with a few differences. Some softwood fiberboard properties tend to degrade faster in elevated humidity environments, while some cane fiberboard properties degrade faster in the hotter dry environments. As a result, it is premature to assume both materials will age at the same rates, and the preliminary aging models developed for cane fiberboard might not apply to softwood fiberboard. However, it is expected that both cane and softwood fiberboard assemblies will perform satisfactorily in conforming packages stored in a typical KAC storage environment for up to 15 years. Aging and testing of softwood fiberboard will continue and additional data will be collected. Additional samples will be added to each aging environment, to support development of an aging model specific to softwood fiberboard. Post-conditioning data have been measured on samples from a single softwood fiberboard assembly, and baseline data are also available from a limited number of vendor-provided samples. This provides minimal information on the possible sample-to-sample variation exhibited by softwood fiberboard. Data to date are generally consistent with the range seen in cane fiberboard, but some portions of the data trends are skewed toward the lower end of that range. Two additional softwood fiberboard source packages have been obtained and will begin to provide data on the range of variability of this material.

  5. WATER RESISTANCE OF WOOD - PLASTIC COMPOSITES MADE FROM WASTE MATERIALS RESULTED IN THE FURNITURE MANUFACTURING PROCESS

    OpenAIRE

    Camelia COŞEREANU; Dumitru LICA; Ioan CURTU; Mariana-Domnica STANCIU

    2014-01-01

    The purpose of this paper is to present innovative wood-plastic composites made from waste materials such as ABS (acrylonitrile butadiene styrene) and wood shavings resulted in the furniture manufacturing process. From previous investigations (with regard to physical integrity and compactness of the panels), only mixtures ranging from a ratio of 100% ABS: 0% shavings to 80% ABS: 20% shavings were selected for water resistance testing. Swelling in thickness and water absorption for...

  6. Evaluation of performance indicators applied to a material recovery facility fed by mixed packaging waste.

    Science.gov (United States)

    Mastellone, Maria Laura; Cremiato, Raffaele; Zaccariello, Lucio; Lotito, Roberta

    2017-06-01

    Most of the integrated systems for municipal solid waste management aim to increase the recycling of secondary materials by means of physical processes including sorting, shredding and reprocessing. Several restrictions prevent from reaching a very high material recycling efficiency: the variability of the composition of new-marketed materials used for packaging production and its shape and complexity are critical issues. The packaging goods are in fact made of different materials (aluminium, polymers, paper, etc.), possibly assembled, having different shape (flat, cylindrical, one-dimensional, etc.), density, colours, optical properties and so on. These aspects limit the effectiveness and efficiency of the sorting and reprocessing plants. The scope of this study was to evaluate the performance of a large scale Material Recovery Facility (MRF) by utilizing data collected during a long period of monitoring. The database resulted from the measured data has been organized in four sections: (1) data related to the amount and type of inlet waste; (2) amount and composition of output products and waste; (3) operating data (such as worked hours for shift, planned and unscheduled maintenance time, setting parameters of the equipment, and energy consumption for shift); (4) economic data (value of each product, disposal price for the produced waste, penalty for non-compliance of products and waste, etc.). A part of this database has been utilized to build an executive dashboard composed by a set of performance indicators suitable to measure the effectiveness and the efficiency of the MRF operations. The dashboard revealed itself as a powerful tool to support managers and engineers in their decisions in respect to the market demand or compliance regulation variation as well as in the designing of the lay-out improvements. The results indicated that the 40% of the input waste was recovered as valuable products and that a large part of these (88%) complied with the standards of

  7. ANALYSIS OF BIODEGRABILITY OF DEGRADABLE/BIODEGRADABLE PLASTIC MATERIAL IN CONTROLLED COMPOSTING ENVIRONMENT

    Directory of Open Access Journals (Sweden)

    Dana Adamcová

    2016-09-01

    Full Text Available We have obtained eight degradable/biodegradable materials based on starch (certified compostable, sample 4–7, HDPE mixed with totally degradable plastic additive (TDPA, sample 2 and polyethylene with the addition of pro-oxidant additive (d2w, sample 1. Composition of sample 3 has not been reported. The materials have been tested as to the rate and character of their degradability/biodegradability in controlled composting conditions. Experiment explored also the effect of degradation/biodegradation of plastic bags on compost quality. The material of the original samples was subjected to assessment using the Nicolet 6700 FT-IR spectrometer, the outcome thereof was obtaining infrared spectra of the samples. For further specification the original samples were tested using the thermogravimetrical analysis. The texture of the foils at different stages of degradation is presented in the Scanning Electron Microscope (SEM photographs. Plastic bags certified as compostable have degraded in laboratory conditions and their degradation had no impact on the quality and features of compost. Selected samples (4, 6 showed significant erosion on surface when subjected to the SEM analysis. Samples labeled (by their producers as 100% degradable (samples 1, 2, 3 did not show any visual signs of degradation and the process of degradation had no impact on the quality and features of compost. Only one of the samples (sample 1 showed certain erosion of surface when submitted for the SEM analysis.

  8. Development of methods for predicting large crack growth in elastic-plastic work-hardening materials in fully plastic conditions

    Science.gov (United States)

    Ford, Hugh; Turner, C. E.; Fenner, R. T.; Curr, R. M.; Ivankovic, A.

    1995-01-01

    The objects of the first, exploratory, stage of the project were listed as: (1) to make a detailed and critical review of the Boundary Element method as already published and with regard to elastic-plastic fracture mechanics, to assess its potential for handling present concepts in two-dimensional and three-dimensional cases. To this was subsequently added the Finite Volume method and certain aspects of the Finite Element method for comparative purposes; (2) to assess the further steps needed to apply the methods so far developed to the general field, covering a practical range of geometries, work hardening materials, and composites: to consider their application under higher temperature conditions; (3) to re-assess the present stage of development of the energy dissipation rate, crack tip opening angle and J-integral models in relation to the possibilities of producing a unified technology with the previous two items; and (4) to report on the feasibility and promise of this combined approach and, if appropriate, make recommendations for the second stage aimed at developing a generalized crack growth technology for its application to real-life problems.

  9. Pyrolysis behavior of different type of materials contained in the rejects of packaging waste sorting plants.

    Science.gov (United States)

    Adrados, A; De Marco, I; Lopez-Urionabarrenechea, A; Caballero, B M; Laresgoiti, M F

    2013-01-01

    In this paper rejected streams coming from a waste packaging material recovery facility have been characterized and separated into families of products of similar nature in order to determine the influence of different types of ingredients in the products obtained in the pyrolysis process. The pyrolysis experiments have been carried out in a non-stirred batch 3.5 dm(3) reactor, swept with 1 L min(-1) N(2), at 500°C for 30 min. Pyrolysis liquids are composed of an organic phase and an aqueous phase. The aqueous phase is greater as higher is the cellulosic material content in the sample. The organic phase contains valuable chemicals as styrene, ethylbenzene and toluene, and has high heating value (HHV) (33-40 MJ kg(-1)). Therefore they could be used as alternative fuels for heat and power generation and as a source of valuable chemicals. Pyrolysis gases are mainly composed of hydrocarbons but contain high amounts of CO and CO(2); their HHV is in the range of 18-46 MJ kg(-1). The amount of COCO(2) increases, and consequently HHV decreases as higher is the cellulosic content of the waste. Pyrolysis solids are mainly composed of inorganics and char formed in the process. The cellulosic materials lower the quality of the pyrolysis liquids and gases, and increase the production of char.

  10. Effects of Micronized Fibers on the Cushion Properties of Foam Buffer Package Materials

    Directory of Open Access Journals (Sweden)

    Chongxing Huang

    2014-08-01

    Full Text Available Foam buffer package materials composed of plant fibers have been a focus of research in recent years because of their environmentally beneficial ability to become fully disintegrated. In this study, bleached bagasse pulp was micronized using a PFI mill, and foam buffer materials were prepared using the micronized fiber. The effects of the beating degree of micronized fibers on the dimensional stability, moisture absorption, static compression, and dynamic compression characteristics were discussed. Results showed that, in both the static and the dynamic compression experiments, the buffer properties improved with an increasing beating degree. The buffer materials made of highly micronized fiber were stronger under pressure and impact. Specifically, the highly micronized fiber’s ability to absorb energy curing impact was improved, demonstrating that it can support a higher compression and impacting load in a certain deformation scope. However, during the drying process, the dimensional stability of the samples also declined with an increasing beating degree. The moisture absorption of the samples improved when the beating degree was increased.

  11. Quantitative assessment of microbiological contributions to corrosion of candidate nuclear waste-package materials

    Energy Technology Data Exchange (ETDEWEB)

    Horn, J.; Jones, D.; Lian, T.; Martin, S.

    1998-10-30

    The U.S. Department of Energy is contributing to the design of a potential nuclear-waste repository at Yucca Mountain, Nevada. A system to predict the contribution of Yucca Mountain (YM) bacteria to overall corrosion rates of candidate waste-package (WP) materials was designed and implemented. DC linear polarization resistance techniques were applied to candidate material coupons that had been inoculated with a mixture of YM-derived bacteria with potentially corrosive activities or left sterile. Inoculated bacteria caused a 5- to 6-fold increase in corrosion rate of carbon steel C1020 (to approximately 7Ð8mm/yr) and an almost 100-fold increase in corrosion rate of Alloy 400 (to approximately 1mm/yr). Microbiologically influenced corrosion (MIC) rates on more resistant materials (CRMs: Alloy 625, Type 304 Stainless Steel, and Alloy C22) were on the order of hundredths of micrometers per year (mm/yr). Bulk chemical and surfacial end-point analyses of spent media and coupon surfaces showed preferential dissolution of nickel from Alloy 400 coupons and depletion of chromium from CRMs after incubation with YM bacteria. Scanning electron microscopy (SEM) also showed greater damage to the Alloy 400 surface than that indicated by electrochemical detection methods.

  12. Selected Plastics Wear Resistance to Bonded Abrasive Particles Compared to Some Ferrous Materials

    Directory of Open Access Journals (Sweden)

    Milan Brožek

    2015-01-01

    Full Text Available Plastics are macromolecular materials without we cannot imagine any branch of human activity with. Plastics have unique properties, often very different from metals. At the choice of the concrete plastic for the concrete application it is necessary to evaluate its mechanical, physical, chemical and technological properties. In last years producers offer also plastics for production of parts exposed to different types of wear. In the contribution the results of wear resistance studying of 10 types of plastics (PTFE, PVC, POM-C, PC, PETP, PEEK, PA66, PP, PA6E and PE-UHMW of one producer are published and compared with test results of four different Fe alloys (grey iron, structural steel, cast steel wear resistant and high-speed steel. The laboratory tests were carried out using the pin-on-disk machine with abrasive cloth (according to ČSN 01 5084, when the abrasive clothes of three different grits (240, 120 and 60 were used. It corresponds to the average abrasive grain sizes of 44.5 µm, 115.5 µm and 275 µm. During the test the test sample was pressed to the abrasive cloth by the pressure of 0.1 MPa. The wear intensity was assessed by the volume, weight and length losses of tested samples. The technical-economical evaluation was the part of the carried out tests. It was univocally proved that at the intensive abrasive wear using the abrasive cloth the best results shows the High-Speed Steel HSS Poldi Radeco 19 810 according to ČSN 41 9810, although its price is relatively high. Other tested Fe alloys, namely grey iron according to ČSN 42 2415, structural steel 11 373 according to ČSN 41 1373 and wear resistant cast steel VPH 6 showed also very favourable properties at the material low price. In comparison with Fe alloys the wear of all plastics was considerably higher and the plastics were considerably more expensive.

  13. Elastic-plastic characterization of a cast stainless steep pipe elbow material

    Energy Technology Data Exchange (ETDEWEB)

    Joyce, J.A. [Naval Academy, Annapolis, MD (United States); Hackett, E.M.; Roe, C. [David W. Taylor Naval Ship Research and Development Center, Annapolis, MD (United States)

    1992-01-01

    Tests conducted in Japan as part of the High Level Vibration Test (HLVT) program for reactor piping systems revealed fatigue crack growth in a cast stainless steel pipe elbow. The material tested was equivalent to ASME SA-351CF8M. The David Taylor Research Center (DTRC) was tasked to developed the appropriate material property data to characterize cyclic deformation, cyclic elastic-plastic crack growth and ductile tearing resistance in the pipe elbow material. It was found that the cast stainless steel was very resistant to ductile crack extension. J-R curves essentially followed a blunting behavior to very high J levels. Low cycle fatigue crack growth rate data obtained on this material using a cyclic J integral approach was consistent with the high cycle fatigue crack growth rate and with a standard textbook correlation equation typical for this type of material. Evaluation of crack closure effects was essential to accurately determine the crack driving force for cyclic elastic- plastic crack growth in this material. SEM examination of several of the cyclic J test fracture surfaces indicated that fatigue was the primary mode of fracture with ductile crack extension intervening only during the last few cycles of loading.

  14. Water plasticization of extruded material made from meat and bone meal and sodium caseinate.

    Science.gov (United States)

    Garcia, Rafael A; Onwulata, Charles I; Ashby, Richard D

    2004-06-16

    Meat and bone meal (MBM) is a high protein agricultural commodity that currently has few applications other than as an animal feed. Unmodified MBM has poor functional properties, due to its low solubility. Our results from pilot plant trials demonstrate that MBM can be extrusion-processed along with sodium caseinate to produce a useful plastic material. We developed this material for use as a dog chew toy. For this application, elastic modulus (stiffness) is a key characteristic. Our results detail the relationship between ambient relative humidity and equilibrium moisture content (MC) in the material. The influence of MC on the glass transition temperature and elastic modulus reflects the plasticization of this material by water. On the basis of a comparison to a commercially available dog chew, the range of stiffness achievable with our material, 0.25-2.50 GPa, encompasses the values appropriate for a dog chew. Our results show that a particular desired stiffness can be maintained by applying an edible moisture barrier to the surface of the material.

  15. Migração específica de antioxidante de embalagens plásticas para alimentos Specific migration of antioxidant from plastic packages for food

    Directory of Open Access Journals (Sweden)

    Leda Coltro

    2011-01-01

    Full Text Available O uso de aditivos em materiais plásticos é essencial para o processamento e desempenho dos plásticos, uma vez que os aditivos conferem características desejadas aos polímeros. No entanto, há restrições determinadas pela Agência Nacional de Vigilância Sanitária (ANVISA para as embalagens plásticas de alimentos, as quais devem ser avaliadas por meio de ensaios físicos, realizados por laboratório acreditado, para verificar se os requisitos estabelecidos pela ANVISA são atendidos. Sendo assim, o objetivo desse trabalho foi desenvolver metodologia que permita a avaliação da migração de 3-(3,5-di-terc-butil-4-hidroxifenil propionato de n-octadecila, antioxidante de nome comercial Irganox 1076, CAS 2082-79-3, presente em embalagens plásticas para contato com alimentos, empregando cromatografia líquida de alta eficiência. Esse estudo também teve como finalidade comprovar se o conteúdo de Irganox 1076 de amostras comerciais de filmes plásticos atende ao requisito de limite de migração específica estabelecido pela ANVISA para este aditivo. Os resultados obtidos indicam que a metodologia utilizada para os simulantes aquoso, ácido e gorduroso é satisfatória e adequada para a análise da migração específica do Irganox 1076, uma vez que todos os parâmetros necessários para a validação do método foram atingidos. As amostras de filme de PEBD e de EVA analisadas atendem ao limite de migração específica do Irganox 1076 para todos os simulantes avaliados.The use of additives in plastics is essential for the processing and performance of plastic products since the additives enhance the desired characteristics of the polymers. Nevertheless, there are restrictions established by the Brazilian Agency of Sanitary Surveillance (ANVISA for plastic packages intended to be in contact with foodstuffs which must be submitted to analyses at a proper laboratory in order to check the compliance with the requirements established

  16. Biodegradability of biodegradable/degradable plastic materials under aerobic and anaerobic conditions.

    Science.gov (United States)

    Mohee, R; Unmar, G D; Mudhoo, A; Khadoo, P

    2008-01-01

    A study was conducted on two types of plastic materials, Mater-Bi Novamont (MB) and Environmental Product Inc. (EPI), to assess their biodegradability under aerobic and anaerobic conditions. For aerobic conditions, organic fractions of municipal solid wastes were composted. For the anaerobic process, anaerobic inoculum from a wastewater treatment plant was used. Cellulose filter papers (CFP) were used as a positive control for both mediums. The composting process was monitored in terms of temperature, moisture and volatile solids and the biodegradation of the samples were monitored in terms of mass loss. Monitoring results showed a biodegradation of 27.1% on a dry basis for MB plastic within a period of 72 days of composting. Biodegradability under an anaerobic environment was monitored in terms of biogas production. A cumulative methane gas production of 245 ml was obtained for MB, which showed good degradation as compared to CFP (246.8 ml). However, EPI plastic showed a cumulative methane value of 7.6 ml for a period of 32 days, which was close to the blank (4.0 ml). The EPI plastic did not biodegrade under either condition. The cumulative carbon dioxide evolution after 32 days was as follows: CFP 4.406 cm3, MB 2.198 cm3 and EPI 1.328 cm3. The cumulative level of CO2 varying with time fitted sigmoid type curves with R2 values of 0.996, 0.996 and 0.995 for CFP, MB and EPI, respectively.

  17. [The application of the nanostructured bioplastic material for the plastic reconstruction of perforations in the nasal septum].

    Science.gov (United States)

    Grigor'eva, M V; Akimov, A V; Bagautdinov, A A

    2014-01-01

    The objective of the present work was to estimate the effectiveness of the application of the nanostructured bioplastic material for the plastic reconstruction of perforations in the nasal septum. A total of 80 patients were recruited for the study. Half of them underwent plastic reconstruction of perforations in the nasal septum with the application of the nanostructured bioplastic material. Forty patients were treated using no biotransplants. The functional state of nasal cavity mucosa was evaluated before and after surgery. It is concluded that the nanostructured bioplastic material used in the present study ensures efficacious reconstruction of nasal septum integrity after plastic correction of septal perforations.

  18. Analysis of the elastic-plastic indentation properties of materials with varying ratio of hardness to Young's modulus

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    The elastic-plastic indentation properties of materials with varying ratio of hardness to Young's modulus (H/E) were analyzed with the finite element method. And the indentation stress fields of materials with varying ratio H/E on the surface were studied by the experiment. The results show that the penetration depth, contact radius, plastic pileup and the degree of elastic recovery depend strongly on the ratio H/E. Moreover, graphs were established to describe the relationship between the elastic-plastic indentation parameters and H/E. The established graphs can be used to predict the H/E of materials when compared with experimental data.

  19. Mineralogical, chemical and physical study of potential buffer and backfill materials from ABM. Test Package 1

    Energy Technology Data Exchange (ETDEWEB)

    Kumpulainen, S.; Kiviranta, L. (B and Tech Oy, Helsinki (Finland))

    2011-07-15

    In the ABM experiment, three test packages with centre steel heaters surrounded by stacks of compacted bentonite rings of various clay materials were placed in boreholes in Aespoe tunnel. The first parcel was saturated with Aespoe groundwater and the heater was turned on simultaneously with the start of saturation. This parcel was excavated 30 months after its installation. Chemical, mineralogical and physical properties of the MX-80, Dep-CaN, Asha and Friedland clay samples from the ABM parcel 1 were analysed and compared to reference samples. Chemical analyses (ICP-AES, C, CO{sub 3}, S, water soluble SO{sub 4}, Fe2+/Fe3+), exchangeable cation analyses, mineralogical analyses (XRD, FTIR) and selective extractions were used to determine changes in the chemistry and mineralogy of ABM materials. Swelling pressure and hydraulic conductivity measurements were performed both for extracted samples and for ground and recompacted samples. Major changes in exchangeable cation composition were observed in all samples originating from equilibration with Aespoe groundwater and interactions with equilibrated waters from neighbouring block materials. Some minor changes in chemical composition were observed as well. Increases in soluble sulphate content in the vicinity of the heater were thought to result from precipitation of sulphate salts. Decreases in sodium content and increases in calcium content were ascribed to changes in exchangeable cations. Interaction with iron was observed to occur only in the close vicinity (first few mm) of the heater. No significantly measureable change in mineralogical composition was seen in any of the studied materials. Extracted Dep-CaN samples showed a slight decrease in swelling pressure. However, when the material was ground, compacted and measured again the swelling pressure was fully recovered. No related change in hydraulic conductivities was observed. (orig.)

  20. Preparation of a Fully Degraded Packaging Material by Using the Mushroom Cultivation Technology%食用菌制全降解包装材料的研究

    Institute of Scientific and Technical Information of China (English)

    尚舒; 牛宏震; 林理量; 苏鑫; 陈万通; 林毅; 曾德芳

    2015-01-01

    In order to diminish the contamination of non -degradable plastic packaging waste on the environment,the straw and wood chips was used as the main raw materials,aided by mushroom cultivation technology,a new type of packaging material which can be completely degraded and is pollution free and cost-effective,was produced.The manufacturing method is simple and suitable for industrialized production. In this experiment,comparison methods are used to study the effect of different ratio of raw materials on my-celial's growth.The result shows that in the ratio of 57% straw,30%wood chips,10% wheat bran,1%gypsum and 2% lime,the mycelium cultivated by pure culture of pleurotus ostreatus is most abundant and has best firmness.By waterproof test and comparing the cushioning property of the materials,we find that the biomass material can totally replace EPS (expanded polystyrene),EPE (expanded polyethylene)and other packaging materials.Meanwhile,the biomass material can be fully degraded in the soil and provide organic fertilizer for soil.%为了解决不可降解的废弃塑料类包装材料对环境的污染,以秸秆和木屑为主要原料,利用食用菌栽培技术制备了一种新型的、可完全降解的包装材料。采用对比实验的方法,研究了不同原料配比对菌丝生长情况的影响,结果表明,在秸秆57%、木屑30%、麸皮10%、石膏1%、石灰2%的配比下,选用平菇菌种栽培的培养基菌丝体含量最多,紧实度最好。通过材料的防水性能测试和缓冲性能比较,表明该生物质材料完全可以替代 EPS(发泡聚苯乙烯)和 EPE (发泡聚乙烯)等包装材料。同时,该生物质材料在土壤中可实现完全降解,为土壤提供有机肥料。