WorldWideScience

Sample records for plastic waste determine

  1. Determining the amount of waste plastics in the feed of Austrian waste-to-energy facilities.

    Science.gov (United States)

    Schwarzböck, Therese; Van Eygen, Emile; Rechberger, Helmut; Fellner, Johann

    2017-02-01

    Although thermal recovery of waste plastics is widely practiced in many European countries, reliable information on the amount of waste plastics in the feed of waste-to-energy plants is rare. In most cases the amount of plastics present in commingled waste, such as municipal solid waste, commercial, or industrial waste, is estimated based on a few waste sorting campaigns, which are of limited significance with regard to the characterisation of plastic flows. In the present study, an alternative approach, the so-called Balance Method, is used to determine the total amount of plastics thermally recovered in Austria's waste incineration facilities in 2014. The results indicate that the plastics content in the waste feed may vary considerably among different plants but also over time. Monthly averages determined range between 8 and 26 wt% of waste plastics. The study reveals an average waste plastics content in the feed of Austria's waste-to-energy plants of 16.5 wt%, which is considerably above findings from sorting campaigns conducted in Austria. In total, about 385 kt of waste plastics were thermally recovered in all Austrian waste-to-energy plants in 2014, which equals to 45 kg plastics cap(-1). In addition, the amount of plastics co-combusted in industrial plants yields a total thermal utilisation rate of 70 kg cap(-1) a(-1) for Austria. This is significantly above published rates, for example, in Germany reported rates for 2013 are in the range of only 40 kg of waste plastics combusted per capita.

  2. Informative document waste plastics

    NARCIS (Netherlands)

    Nagelhout D; Sein AA; Duvoort GL

    1989-01-01

    This "Informative document waste plastics" forms part of a series of "informative documents waste materials". These documents are conducted by RIVM on the indstruction of the Directorate General for the Environment, Waste Materials Directorate, in behalf of the program of

  3. Informative document waste plastics

    NARCIS (Netherlands)

    Nagelhout D; Sein AA; Duvoort GL

    1989-01-01

    This "Informative document waste plastics" forms part of a series of "informative documents waste materials". These documents are conducted by RIVM on the indstruction of the Directorate General for the Environment, Waste Materials Directorate, in behalf of the program of acti

  4. Determination of heavy metals and halogens in plastics from electric and electronic waste.

    Science.gov (United States)

    Dimitrakakis, Emmanouil; Janz, Alexander; Bilitewski, Bernd; Gidarakos, Evangelos

    2009-10-01

    The presence of hazardous substances and preparations in small waste electrical and electronic equipment (sWEEE) found in the residual household waste stream of the city of Dresden, Germany has been investigated. The content of sWEEE plastics in heavy metals and halogens is determined using handheld X-ray fluorescence analysis (HXRF), elemental analysis by means of atomic absorption spectrometry (AAS) and ion exchange chromatography (IEC). Mean value of results for heavy metals in samples (n=51) by AAS are 17.4 mg/kg for Pb, 5.7 mg/kg for Cd, 8.4 mg/kg for Cr. The mass fraction of an additive as shown by HXRF (n=161) can vary over a wide range. Precise deductions as regards sWEEE plastics content in hazardous substances and preparations cannot be made. Additional research would be expedient regarding the influence of hazardous substances to recycling processes, in particular regarding the contamination of clean fractions in the exit streams of a WEEE treatment plant. Suitable standards for calibrating HXRF for use on EEE plastics or complex electr(on)ic components do not exist and should be developed.

  5. Determinants of recycling common types of plastic product waste in environmental horticulture industry: The case of Georgia.

    Science.gov (United States)

    Meng, Ting; Klepacka, Anna M; Florkowski, Wojciech J; Braman, Kristine

    2016-02-01

    Environmental horticulture firms provide a variety of commercial/residential landscape products and services encompassing ornamental plant production, design, installation, and maintenance. The companies generate tons of waste including plastic containers, trays, and greenhouse/field covers, creating the need to reduce and utilize plastic waste. Based on survey data collected in Georgia in 2013, this paper investigates determinants of the environmental horticulture firms' recycling decision (plastic containers, flats, and greenhouse poly). Our findings indicate that the decision to discard vs. recycle plastic containers, flats, and greenhouse poly is significantly influenced by firm scope, size, location, and partnership with recycling providers, as well as whether recycling providers offer additional waste pickup services. Insights from this study are of use to local governments and environmental organizations interested in increasing horticultural firm participation in recycling programs and lowering the volume of plastic destined for landfills.

  6. PLASMA GASIFICATION OF WASTE PLASTICS

    Directory of Open Access Journals (Sweden)

    Tadeusz Mączka

    2013-01-01

    Full Text Available The article presents the process of obtaining liquid fuels and fuel gas in the process of plasma processing of organic materials, including waste plastics. The concept of plasma pyrolysis of plastics was presented and on its basis a prototype installation was developed. The article describes a general rule of operating the installation and its elements in the process and basic operation parameters determined during its start-up. Initial results of processing plastics and the directions further investigations are also discussed. The effect of the research is to be the design of effective technology of obtaining fuels from gasification/pyrolysis of organic waste and biomass.

  7. Sorting Plastic Waste in Hydrocyclone

    Directory of Open Access Journals (Sweden)

    Ernestas Šutinys

    2011-02-01

    Full Text Available The article presents material about sorting plastic waste in hydrocyclone. The tests on sorting plastic waste were carried out. Also, the findings received from the performed experiment on the technology of sorting plastic waste are interpreted applying an experimental model of the equipment used for sorting plastics of different density.Article in Lithuanian

  8. Biodegradability of degradable plastic waste.

    Science.gov (United States)

    Agamuthu, P; Faizura, Putri Nadzrul

    2005-04-01

    Plastic waste constitutes the third largest waste volume in Malaysian municipal solid waste (MSW), next to putrescible waste and paper. The plastic component in MSW from Kuala Lumpur averages 24% (by weight), whereas the national mean is about 15%. The 144 waste dumps in the country receive about 95% of the MSW, including plastic waste. The useful life of the landfills is fast diminishing as the plastic waste stays un-degraded for more than 50 years. In this study the compostability of polyethylene and pro-oxidant additive-based environmentally degradable plastics (EDP) was investigated. Linear low-density polyethylene (LLDPE) samples exposed hydrolytically or oxidatively at 60 degrees C showed that the abiotic degradation path was oxidative rather than hydrolytic. There was a weight loss of 8% and the plastic has been oxidized as shown by the additional carbonyl group exhibited in the Fourier transform infra red (FTIR) Spectrum. Oxidation rate seemed to be influenced by the amount of pro-oxidant additive, the chemical structure and morphology of the plastic samples, and the surface area. Composting studies during a 45-day experiment showed that the percentage elongation (reduction) was 20% for McD samples [high-density polyethylene, (HDPE) with 3% additive] and LL samples (LLDPE with 7% additive) and 18% reduction for totally degradable plastic (TDP) samples (HDPE with 3% additive). Lastly, microbial experiments using Pseudomonas aeroginosa on carbon-free media with degradable plastic samples as the sole carbon source, showed confirmatory results. A positive bacterial growth and a weight loss of 2.2% for degraded polyethylene samples were evident to show that the degradable plastic is biodegradable.

  9. Marine pollution. Plastic waste inputs from land into the ocean.

    Science.gov (United States)

    Jambeck, Jenna R; Geyer, Roland; Wilcox, Chris; Siegler, Theodore R; Perryman, Miriam; Andrady, Anthony; Narayan, Ramani; Law, Kara Lavender

    2015-02-13

    Plastic debris in the marine environment is widely documented, but the quantity of plastic entering the ocean from waste generated on land is unknown. By linking worldwide data on solid waste, population density, and economic status, we estimated the mass of land-based plastic waste entering the ocean. We calculate that 275 million metric tons (MT) of plastic waste was generated in 192 coastal countries in 2010, with 4.8 to 12.7 million MT entering the ocean. Population size and the quality of waste management systems largely determine which countries contribute the greatest mass of uncaptured waste available to become plastic marine debris. Without waste management infrastructure improvements, the cumulative quantity of plastic waste available to enter the ocean from land is predicted to increase by an order of magnitude by 2025.

  10. An efficient and fast analytical procedure for the bromine determination in waste electrical and electronic equipment plastics.

    Science.gov (United States)

    Taurino, R; Cannio, M; Mafredini, T; Pozzi, P

    2014-01-01

    In this study, X-ray fluorescence (XRF) spectroscopy was used, in combination with micro-Raman spectroscopy, for a fast determination of bromine concentration and then of brominated flame retardants (BFRs) compounds in waste electrical and electronic equipments. Different samples from different recycling industries were characterized to evaluate the sorting performances of treatment companies. This investigation must be considered of prime research interest since the impact of BFRs on the environment and their potential risk on human health is an actual concern. Indeed, the new European Restriction of Hazardous Substances Directive (RoHS 2011/65/EU) demands that plastics with BFRs concentration above 0.1%, being potential health hazards, are identified and eliminated from the recycling process. Our results show the capability and the potential of Raman spectroscopy, together with XRF analysis, as effective tools for the rapid detection of BFRs in plastic materials. In particular, the use of these two techniques in combination can be considered as a promising method suitable for quality control applications in the recycling industry.

  11. Sustainable reverse logistics for household plastic waste

    OpenAIRE

    Bing, X

    2014-01-01

    Summary of the thesis titled “Sustainable Reverse Logistics for Household Plastic Waste” PhD Candidate: Xiaoyun Bing Recycled plastic can be used in the manufacturing of plastic products to reduce the use of virgin plastics material. The cost of recycled plastics is usually lower than that of virgin plastics. Therefore, it is environmentally and economically beneficial to improve the plastic recycling system to ensure more plastic waste from households is properly collected and pr...

  12. Process for remediation of plastic waste

    Science.gov (United States)

    Pol, Vilas G [Westmont, IL; Thiyagarajan, Pappannan [Germantown, MD

    2012-04-10

    A single step process for degrading plastic waste by converting the plastic waste into carbonaceous products via thermal decomposition of the plastic waste by placing the plastic waste into a reactor, heating the plastic waste under an inert or air atmosphere until the temperature of 700.degree. C. is achieved, allowing the reactor to cool down, and recovering the resulting decomposition products therefrom. The decomposition products that this process yields are carbonaceous materials, and more specifically egg-shaped and spherical-shaped solid carbons. Additionally, in the presence of a transition metal compound, this thermal decomposition process produces multi-walled carbon nanotubes.

  13. Environmental evaluation of plastic waste management scenarios

    DEFF Research Database (Denmark)

    Rigamonti, L.; Grosso, M.; Møller, Jacob

    2014-01-01

    The management of the plastic fraction is one of the most debated issues in the discussion on integrated municipal solid waste systems. Both material and energy recovery can be performed on such a waste stream, and different separate collection schemes can be implemented. The aim of the paper...... is to contribute to the debate, based on the analysis of different plastic waste recovery routes. Five scenarios were defined and modelled with a life cycle assessment approach using the EASEWASTE model. In the baseline scenario (P0) the plastic is treated as residual waste and routed partly to incineration...... with energy recovery and partly to mechanical biological treatment. A range of potential improvements in plastic management is introduced in the other four scenarios (P1–P4). P1 includes a source separation of clean plastic fractions for material recycling, whereas P2 a source separation of mixed plastic...

  14. Flash Cracking Reactor for Waste Plastic Processing

    Science.gov (United States)

    Timko, Michael T.; Wong, Hsi-Wu; Gonzalez, Lino A.; Broadbelt, Linda; Raviknishan, Vinu

    2013-01-01

    Conversion of waste plastic to energy is a growing problem that is especially acute in space exploration applications. Moreover, utilization of heavy hydrocarbon resources (wastes, waxes, etc.) as fuels and chemicals will be a growing need in the future. Existing technologies require a trade-off between product selectivity and feedstock conversion. The objective of this work was to maintain high plastic-to-fuel conversion without sacrificing the liquid yield. The developed technology accomplishes this goal with a combined understanding of thermodynamics, reaction rates, and mass transport to achieve high feed conversion without sacrificing product selectivity. The innovation requires a reaction vessel, hydrocarbon feed, gas feed, and pressure and temperature control equipment. Depending on the feedstock and desired product distribution, catalyst can be added. The reactor is heated to the desired tempera ture, pressurized to the desired pressure, and subject to a sweep flow at the optimized superficial velocity. Software developed under this project can be used to determine optimal values for these parameters. Product is vaporized, transferred to a receiver, and cooled to a liquid - a form suitable for long-term storage as a fuel or chemical. An important NASA application is the use of solar energy to convert waste plastic into a form that can be utilized during periods of low solar energy flux. Unlike previous work in this field, this innovation uses thermodynamic, mass transport, and reaction parameters to tune product distribution of pyrolysis cracking. Previous work in this field has used some of these variables, but never all in conjunction for process optimization. This method is useful for municipal waste incinerator operators and gas-to-liquids companies.

  15. A review of plastic waste biodegradation.

    Science.gov (United States)

    Zheng, Ying; Yanful, Ernest K; Bassi, Amarjeet S

    2005-01-01

    With more and more plastics being employed in human lives and increasing pressure being placed on capacities available for plastic waste disposal, the need for biodegradable plastics and biodegradation of plastic wastes has assumed increasing importance in the last few years. This review looks at the technological advancement made in the development of more easily biodegradable plastics and the biodegradation of conventional plastics by microorganisms. Additives, such as pro-oxidants and starch, are applied in synthetic materials to modify and make plastics biodegradable. Recent research has shown that thermoplastics derived from polyolefins, traditionally considered resistant to biodegradation in ambient environment, are biodegraded following photo-degradation and chemical degradation. Thermoset plastics, such as aliphatic polyester and polyester polyurethane, are easily attacked by microorganisms directly because of the potential hydrolytic cleavage of ester or urethane bonds in their structures. Some microorganisms have been isolated to utilize polyurethane as a sole source of carbon and nitrogen source. Aliphatic-aromatic copolyesters have active commercial applications because of their good mechanical properties and biodegradability. Reviewing published and ongoing studies on plastic biodegradation, this paper attempts to make conclusions on potentially viable methods to reduce impacts of plastic waste on the environment.

  16. Plastic waste as a resource. Strategies for reduction and utilization of plastic waste

    OpenAIRE

    Pasqual i Camprubí, Gemma

    2010-01-01

    Plastic materials have experienced a spectacular rate of growth in recent decades, consequently, production of plastics, and likewise their consumption, has increased markedly since 1950. Moreover, they are lightweight and durable, as well as can be moulded into a variety of products that can be manufactured in many different types of plastic and in a wide range of applications. Inevitably, continually increasing amounts of used plastic are originating daily, resulting in a plastic waste prob...

  17. Managing plastic waste in East Africa: Niche innovations in plastic production and solid waste

    NARCIS (Netherlands)

    Ombis, L.O.; Vliet, van B.J.M.; Mol, A.P.J.

    2015-01-01

    This paper assesses the uptake of environmental innovation practices to cope with plastic waste in Kenyan urban centres at the interface of solid waste management and plastic production systems. The Multi Level Perspective on Technological Transitions is used to evaluate 7 innovation pathways of pla

  18. Managing plastic waste in East Africa: Niche innovations in plastic production and solid waste

    NARCIS (Netherlands)

    Ombis, L.O.; Vliet, van B.J.M.; Mol, A.P.J.

    2015-01-01

    This paper assesses the uptake of environmental innovation practices to cope with plastic waste in Kenyan urban centres at the interface of solid waste management and plastic production systems. The Multi Level Perspective on Technological Transitions is used to evaluate 7 innovation pathways of

  19. Utilization of Electronic Waste Plastic in Concrete

    Directory of Open Access Journals (Sweden)

    Vivek S. Damal

    2015-04-01

    Full Text Available In India, bitumen pavements are commonly used for highways. Due to the increasing traffic intensity, distress such as rutting and cracking of pavements are very common in Indian roads. Under varying seasonal temperature, flexible pavements tend to become soft in summer and brittle in winter. Investigations revealed that properties of concrete can be better than bitumen roads. But now a day‟s concrete roads are used commonly because concrete roads have more life span than the bitumen roads. In large cities now a day‟s concrete roads are used because concrete roads are more durable, strengthen and having more life span than bitumen roads. Waste plastics and E-waste (electronic waste both by domestic and industrial sectors can be used in the production of asphalt mix. Waste plastic, mainly used for packing are made up of polyethylene, polypropylene, polystyrene. Electronic waste, abbreviated as e-waste, consists of discarded old computers, TVs, refrigerators; radios, etc are basically any electrical or electronic appliance that has reached its end of life. An experimental study is made on the utilization of E-waste particles as fine aggregates in concrete with a percentage replacement ranging from 0 % to 21.5% i.e. (7.5%, 15% and 21.5% on the strength criteria of M30 Concrete. Compressive strength Concrete with and without E- waste plastic as aggregates was observed which exhibits a good strength. The feasibility of utilizing E-waste plastic particles as partial replacement of fine aggregate has been presented. In the present study, compressive strength was investigated for Optimum Cement Content and 7.5% E-plastic content in mix yielded stability and very good in compressive strength of 43 grade cement.

  20. Waste-to-energy: Dehalogenation of plastic-containing wastes.

    Science.gov (United States)

    Shen, Yafei; Zhao, Rong; Wang, Junfeng; Chen, Xingming; Ge, Xinlei; Chen, Mindong

    2016-03-01

    The dehalogenation measurements could be carried out with the decomposition of plastic wastes simultaneously or successively. This paper reviewed the progresses in dehalogenation followed by thermochemical conversion of plastic-containing wastes for clean energy production. The pre-treatment method of MCT or HTT can eliminate the halogen in plastic wastes. The additives such as alkali-based metal oxides (e.g., CaO, NaOH), iron powders and minerals (e.g., quartz) can work as reaction mediums and accelerators with the objective of enhancing the mechanochemical reaction. The dehalogenation of waste plastics could be achieved by co-grinding with sustainable additives such as bio-wastes (e.g., rice husk), recyclable minerals (e.g., red mud) via MCT for solid fuels production. Interestingly, the solid fuel properties (e.g., particle size) could be significantly improved by HTT in addition with lignocellulosic biomass. Furthermore, the halogenated compounds in downstream thermal process could be eliminated by using catalysts and adsorbents. Most dehalogenation of plastic wastes primarily focuses on the transformation of organic halogen into inorganic halogen in terms of halogen hydrides or salts. The integrated process of MCT or HTT with the catalytic thermal decomposition is a promising way for clean energy production. The low-cost additives (e.g., red mud) used in the pre-treatment by MCT or HTT lead to a considerable synergistic effects including catalytic effect contributing to the follow-up thermal decomposition.

  1. Pyrolysis of plastics and tyres wastes

    Energy Technology Data Exchange (ETDEWEB)

    Miranda, Miguel; Costa, Paula; Pinto, Filomena; Gulyurtlu, Ibrahim; Cabrita, Isabel [INETI/DEECA, Lisboa (Portugal)

    2002-07-01

    The main aim of the work is to characterize the nature of liquids produced by pyrolysing various blends of wastes were several mixtures of tyres and plastics wastes were pyrolysed. The plastics wastes used were polyethylene (PE), polypropylene (PP) and polystyrene (PS). The tyre waste also included natural rubber (NR), styrene butadiene rubber (SBR) and butadiene rubber (BR).The influence of the following operating conditions as well as different mixture of wastes on nature of the products was investigated; run temperature: 380-450 deg C, run pressure: 0.2-8.0 MPa, reaction time: 10 to 60 minutes, waste composition: several mixtures of plastics and tyres in different quantities. The final objective was to optimize operating condition to maximize the production of liquids and to achieve selectivity in the nature of the liquids obtained. The results obtained showed that the composition of the end products was highly dependent of the components of the blend of wastes used. Several solvents with different H-donor capacity were also added to the reaction mixture to investigate the nature of liquids formed to verify if a higher degree of selectivity could be achieved with regard to the nature of liquid products. Solvents used included 1,2,3,4 - Tetrahydronaphthalene and 1,2,3,4 - tetrahydroquinoline. Liquids yields obtained so far were found to be very promising, reaching values around 70% (v/v), while gas and residual solid amounts were around 10% (v/v) and 20% (v/v).

  2. Waste Plastic Converting into Hydrocarbon Fuel Materials

    Energy Technology Data Exchange (ETDEWEB)

    Sarker, Moinuddin; Mamunor Rashid, Mohammad; Molla, Mohammad

    2010-09-15

    The increased demand and high prices for energy sources are driving efforts to convert organic compounds into useful hydrocarbon fuels. Although much of this work has focused on biomass, there are strong benefits to deriving fuels from waste plastic material. Natural State Research Inc. (NSR) has invented a simple and economically viable process to decompose the hydrocarbon polymers of waste plastic into the shorter chain hydrocarbon of liquid fuel (patent pending). The method and principle of the production / process will be discussed. Initial tests with several widely used polymers indicate a high potential for commercialization.

  3. Waste Plastic Fibre Reinforced Self Compacting Concrete

    Directory of Open Access Journals (Sweden)

    Mrs. Vijaya G.S Assistant Professor

    2016-05-01

    Full Text Available Self-compacting concrete is high performance concrete which is highly flowable, non-segregating, spread on its own weight and doesn‟t need any compaction. This paper deals with flow and strength characteristics such as compressive strength, split tensile strength, flexural strength and impact strength of Self-compacting concrete with various percentages of waste plastic fibres like 0%, 0.25%, 0.5%, 0.75%, 1.0%, 1.1%, 1.20%, 1.3% and 1.4% is added by weight of cement. The mix proportion for M40 grade of concrete was done by using Nan Su method (Cement: GGBS: Fine aggregate: Course aggregate 1: 0.705: 3.34: 2.62. Water powder (W/P ratio 0.36, cement content 280kg/m3 , GGBS 220 kg/m3 was calculated and maintained as constant throughout the experimental work for all eight mixes, only the superplastizers dosage was varied for different percentage of fibres. In this experimental investigation one control mix and eight (8 different mixes were considered. Totally 81 Cube, beam, Cylindrical specimens and square plates were casted, cured and tested as per IS specifications. For determining impact strength drop weight method was used. The results obtained indicate that fresh (workability characteristics satisfy the lower and upper limit as suggested by EFNARC. The tests on hardened properties indicate that the compressive strength, split tensile strength, flexural strength was improved proportionally with the addition of waste plastic fibers upto 1.0% by weight of cement and then decreases. The impact strength improved proportionally with addition of fibres upto 1.2% by weight of cement and then decreases.

  4. Thermal and catalytic pyrolysis of plastic waste

    OpenAIRE

    Débora Almeida; Maria de Fátima Marques

    2016-01-01

    Abstract The amount of plastic waste is growing every year and with that comes an environmental concern regarding this problem. Pyrolysis as a tertiary recycling process is presented as a solution. Pyrolysis can be thermal or catalytical and can be performed under different experimental conditions. These conditions affect the type and amount of product obtained. With the pyrolysis process, products can be obtained with high added value, such as fuel oils and feedstock for new products. Zeolit...

  5. Pyrolysis of waste plastic crusts of televisions.

    Science.gov (United States)

    Liu, Xinmin; Wang, Zhen; Xu, Dongyan; Guo, Qingjie

    2012-09-01

    The disposal of waste plastic crusts of televisions is an issue that is gaining increasing interest around the world. In this investigation, the pyrolysis and catalytic cracking of the waste television crusts mainly composed of acrylonitrile--butadiene-styrene copolymer was studied. Thermogravimetric analysis was used for initial characterization of the pyrolysis of the waste plastic, but most of the investigations were carried out using a 600 mL tubing reactor. Effects of temperature, reaction time and catalyst on the pyrolysis of the waste television crusts were investigated. The results showed that the oil yield increased with increasing temperature or with prolongation of reaction time. With increasing temperature, the generating percentage of gasoline and diesel oil increased, but the heavy oil yield decreased. Zinc oxide, iron oxide and fluid catalytic cracking catalyst (FCC catalyst) were employed to perform a series of experiments. It was demonstrated that the liquid product was markedly improved and the reaction temperature decreased 100 degrees C when FCC was used. The composition ofpyrolysis oils was analysed using gas chromatography-mass spectrometry, and they contained 36.49% styrene, 19.72% benzenebutanenitrile, 12.1% alpha-methylstyrene and 9.69% dimethylbenzene.

  6. Combating oil spill problem using plastic waste

    Energy Technology Data Exchange (ETDEWEB)

    Saleem, Junaid, E-mail: junaidupm@gmail.com [Department of Chemical Engineering, University of Karachi (Pakistan); Ning, Chao; Barford, John [Department of Chemical and Biomolecular Engineering, Hong Kong University of Science and Technology, Clear Water Bay, Kowloon (Hong Kong); McKay, Gordon [Department of Chemical and Biomolecular Engineering, Hong Kong University of Science and Technology, Clear Water Bay, Kowloon (Hong Kong); Division of Sustainable Development, College of Science, Engineering and Technology, Hamad Bin Khalifa University, Qatar Foundation, Doha (Qatar)

    2015-10-15

    Highlights: • Up-cycling one type of pollution i.e. plastic waste and successfully using it to combat the other type of pollution i.e. oil spill. • Synthesized oil sorbent that has extremely high oil uptake of 90 g/g after prolonged dripping of 1 h. • Synthesized porous oil sorbent film which not only facilitates in oil sorption but also increases the affinity between sorbent and oil by means of adhesion. - Abstract: Thermoplastic polymers (such as polypropylene, polyethylene, polyethylene terephthalate (PET) and high density polyethylene (HDPE)) constitute 5–15% of municipal solid waste produced across the world. A huge quantity of plastic waste is disposed of each year and is mostly either discarded in landfills or incinerated. On the other hand, the usage of synthetic polymers as oil sorbents, in particular, polyolefins, including polypropylene (PP), and polyethylene (PE) are the most commonly used oil sorbent materials mainly due to their low cost. However, they possess relatively low oil absorption capacities. In this work, we provide an innovative way to produce a value-added product such as oil-sorbent film with high practical oil uptake values in terms of g/g from waste HDPE bottles for rapid oil spill remedy.

  7. UTILIZATION OF WASTE PLASTIC BOTTLES IN ASPHALT MIXTURE

    Directory of Open Access Journals (Sweden)

    TAHER BAGHAEE MOGHADDAM

    2013-06-01

    Full Text Available Nowadays, large amounts of waste materials are being produced in the world. One of the waste materials is plastic bottle. Generating disposable plastic bottles is becoming a major problem in many countries. Using waste plastic as a secondary material in construction projects would be a solution to overcome the crisis of producing large amount of waste plastics in one hand and improving the structure’s characteristics such as resistance against cracking on the other hand. This study aimed to investigate the effects of adding plastic bottles in road pavement. Marshall properties as well as specific gravity of asphalt mixture containing different percentages of plastic bottles were evaluated. Besides, Optimum Asphalt Content (OAC was calculated for each percentages of plastic bottles used in the mix. The stiffness and fatigue characteristics of mixture were assessed at OAC value. Results showed that the stability and flow values of asphalt mixture increased by adding waste crushed plastic bottle into the asphalt mixture. Further, it was shown that the bulk specific gravity and stiffness of mixtures increased by adding lower amount of plastic bottles; however, adding higher amounts of plastic resulted in lower specific gravity and mix stiffness. In addition, it was concluded that the mixtures containing waste plastic bottles have lower OAC values compared to the conventional mixture, and this may reduce the amount of asphalt binder can be used in road construction projects. Besides, the mixtures containing waste plastic showed significantly greater fatigue resistance than the conventional mixture.

  8. Determination of Cd, Cr, Hg and Pb in plastics from waste electrical and electronic equipment by inductively coupled plasma mass spectrometry with collision-reaction interface technology.

    Science.gov (United States)

    Santos, Mirian C; Nóbrega, Joaquim A; Cadore, Solange

    2011-06-15

    A procedure based on the use of a quadrupole inductively coupled plasma-mass spectrometer equipped with a collision-reaction interface (CRI) for control of spectral overlap interferences was developed for simultaneous determination of Cd, Cr, Hg, and Pb in plastics from waste electrical and electronic equipment (WEEE). The injection of H(2) and He (80 and 60 mL min(-1), respectively) into the sampled plasma, colliding and reacting with potentially interfering polyatomic ions, allows interference-free determination of chromium via its isotopes (52)Cr and (53)Cr that are freed from overlap due to the occurrence of (40)Ar(12)C(+), (40)Ar(12)C(1)H(+), (36)S(16)O(+) or (1)H(36)S(16)O(+). Cadmium, Hg and Pb were directly determined via their isotopes (110)Cd, (111)Cd, (112)Cd, (199)Hg, (200)Hg, (201)Hg, (202)Hg, (206)Pb, (207)Pb, and (208)Pb, without using CRI. The CRI can be quickly activated or deactivated before each analyte measurement. Limits of detection for (52)Cr were 0.04 or 0.14 μg L(-1) with He or H(2) injected in CRI. Cadmium and Pb have LODs between 0.02 and 0.08 μg L(-1) and Hg had 0.93-0.98 μg L(-1), without using CRI. Analyte concentrations for samples varied from 16 to 43, 1 to 11, 4 to 12, and 5 to 13 mg kg(-1) for Cr, Cd, Hg and Pb, respectively.

  9. Combustion of char from plastic wastes pyrolysis

    Science.gov (United States)

    Saptoadi, Harwin; Rohmat, Tri Agung; Sutoyo

    2016-06-01

    A popular method to recycle plastic wastes is pyrolysis, where oil, gas and char can be produced. These products can be utilized as fuels because they are basically hydrocarbons. The research investigates char properties, including their performance as fuel briquettes. There are 13 char samples from PE (Polyethylene) pyrolyzed at temperatures of around 450 °C, with and without a catalyst. Some of the samples were obtained from PE mixed with other types, such as Polystyrene (PS), Polypropylene (PP), Polyethylene Terephthalate (PET), and Others. Char properties, such as moisture, ash, volatile matter, and fixed carbon contents, are revealed from the proximate analysis, whereas calorific values were measured with a bomb calorimeter. Briquettes are made by mixing 4 g of char with 0.5 - 1 g binder. Briquettes are hollow cylinders with an outer and inner diameter of around 1.75 cm and 0.25 cm, respectively. Combustion is carried out in a furnace with wall temperatures of about 230°C and a constant air velocity of 0.7 m/s. Five out of 13 char briquettes are not feasible because they melt during combustion. Briquettes made from 100% PE wastes burn in substantially shorter duration than those from mixed plastic wastes. Char #1 and #5 are excellent due to their highest energy release, whereas #10 show the worst performance.

  10. Thermal and catalytic pyrolysis of plastic waste

    Directory of Open Access Journals (Sweden)

    Débora Almeida

    2016-02-01

    Full Text Available Abstract The amount of plastic waste is growing every year and with that comes an environmental concern regarding this problem. Pyrolysis as a tertiary recycling process is presented as a solution. Pyrolysis can be thermal or catalytical and can be performed under different experimental conditions. These conditions affect the type and amount of product obtained. With the pyrolysis process, products can be obtained with high added value, such as fuel oils and feedstock for new products. Zeolites can be used as catalysts in catalytic pyrolysis and influence the final products obtained.

  11. Flotation separation of waste plastics for recycling-A review.

    Science.gov (United States)

    Wang, Chong-qing; Wang, Hui; Fu, Jian-gang; Liu, You-nian

    2015-07-01

    The sharp increase of plastic wastes results in great social and environmental pressures, and recycling, as an effective way currently available to reduce the negative impacts of plastic wastes, represents one of the most dynamic areas in the plastics industry today. Froth flotation is a promising method to solve the key problem of recycling process, namely separation of plastic mixtures. This review surveys recent literature on plastics flotation, focusing on specific features compared to ores flotation, strategies, methods and principles, flotation equipments, and current challenges. In terms of separation methods, plastics flotation is divided into gamma flotation, adsorption of reagents, surface modification and physical regulation.

  12. Chemical recycling of mixed waste plastics by selective pyrolysis

    Energy Technology Data Exchange (ETDEWEB)

    Tatsumoto, K.; Meglen, R.; Evans, R. [National Renewable Energy Laboratory, Golden, CO (United States)

    1995-05-01

    The goal of this work is to use selective pyrolysis to produce high-value chemicals from waste plastics mixtures. Selectivity is achieved by exploiting differences in reaction rates, catalysis, and coreactants. Target wastes are molecular mixtures such as; blends or composites, or mixtures from manufactured products such as; carpets and post-consumer mixed-plastic wastes. The experimental approach has been to use small-scale experiments using molecular beam mass spectrometry (MBMS), which provides rapid analysis of reaction products and permits rapid screening of process parameters. Rapid screening experiments permit exploration of many potential waste stream applications for the selective pyrolysis process. After initial screening, small-scale, fixed-bed and fluidized-bed reactors are used to provide products for conventional chemical analysis, to determine material balances, and to test the concept under conditions that will be used at a larger scale. Computer assisted data interpretation and intelligent chemical processing are used to extract process-relevant information from these experiments. An important element of this project employs technoeconomic assessments and market analyses of durables, the availability of other wastes, and end-product uses to identify target applications that have the potential for economic success.

  13. Triboelectrostatic separation for granular plastic waste recycling: a review.

    Science.gov (United States)

    Wu, Guiqing; Li, Jia; Xu, Zhenming

    2013-03-01

    The world's plastic consumption has increased incredibly in recent decades, generating more and more plastic waste, which makes it a great public concern. Recycling is the best treatment for plastic waste since it cannot only reduce the waste but also reduce the consumption of oil for producing new virgin plastic. Mechanical recycling is recommended for plastic waste to avoid the loss of its virgin value. As a mechanical separation technology, triboelectrostatic separation utilizes the difference between surface properties of different materials to get them oppositely charged, deflected in the electric field and separately collected. It has advantages such as high efficiency, low cost, no concern of water disposal or secondary pollution and a relatively wide processing range of particle size especially suitable for the granular plastic waste. The process of triboelectrostatic separation for plastic waste is reviewed in this paper. Different devices have been developed and proven to be effective for separation of plastic waste. The influence factors are also discussed. It can be concluded that the triboelectrostatic separation of plastic waste is a promising technology. However, more research is required before it can be widely applied in industry.

  14. Characterization of plastic blends made from mixed plastics waste of different sources.

    Science.gov (United States)

    Turku, Irina; Kärki, Timo; Rinne, Kimmo; Puurtinen, Ari

    2017-02-01

    This paper studies the recyclability of construction and household plastic waste collected from local landfills. Samples were processed from mixed plastic waste by injection moulding. In addition, blends of pure plastics, polypropylene and polyethylene were processed as a reference set. Reference samples with known plastic ratio were used as the calibration set for quantitative analysis of plastic fractions in recycled blends. The samples were tested for the tensile properties; scanning electron microscope-energy-dispersive X-ray spectroscopy was used for elemental analysis of the blend surfaces and Fourier transform infrared (FTIR) analysis was used for the quantification of plastics contents.

  15. Recycling of plastic waste: Presence of phthalates in plastics from households and industry

    DEFF Research Database (Denmark)

    Pivnenko, Kostyantyn; Eriksen, Marie Kampmann; Martín-Fernández, J. A.

    2016-01-01

    Plastics recycling has the potential to substitute virgin plastics partially as a source of raw materials in plastic product manufacturing. Plastic as a material may contain a variety of chemicals, some potentially hazardous. Phthalates, for instance, are a group of chemicals produced in large...... recognised, the influence of plastic recycling on phthalate content has been hypothesised but not well documented. In the present work we analysed selected phthalates (DMP, DEP, DPP, DiBP, DBP, BBzP, DEHP, DCHP and DnOP) in samples of waste plastics as well as recycled and virgin plastics. DBP, DiBP and DEHP...... product manufacturing (labelling, gluing, etc.) and were not removed following recycling of household waste plastics. Furthermore, DEHP was identified as a potential indicator for phthalate contamination of plastics. Close monitoring of plastics intended for phthalates-sensitive applications...

  16. Recycling and Utilization of Waste Glass Fiber Reinforced Plastics

    Directory of Open Access Journals (Sweden)

    Feng Yan-chao

    2016-01-01

    Full Text Available This paper mainly introduced the recovery method, classification and comprehensive utilization process of waste glass fiber reinforced plastics (GFRP. Among the current methods of utilization, the physical method is most promising. After pre-processing of waste GFRP, the short glass fiber can be used in gypsum block to improve the anti-cracking and operation performance of the material; waste GFRP powder can be used in plastic fiber reinforced manhole covers to increase the mechanical strength, and the products conformed to JC 1009-2006. Based on these studies, we also point out some problems concerning the utilization of waste glass fiber reinforced plastics.

  17. Recycling of plastic waste: Screening for brominated flame retardants (BFRs)

    DEFF Research Database (Denmark)

    Pivnenko, Kostyantyn; Granby, Kit; Eriksson, Eva

    2017-01-01

    on the other hand, has resulted in dispersion and accumulation of selected BFRs in the environment and receiving biota. A wide range of plastic products may contain BFRs. This affects the quality of waste plastics as secondary resource: material recycling may potentially reintroduce the BFRs into new plastic......,4,6-TBP)), hexabromocyclododecane stereoisomers (α-, β-, and γ-HBCD), as well as selected polybrominated diphenyl ethers (PBDEs) in samples of household waste plastics, virgin and recycled plastics. A considerable number of samples contained BFRs, with highest concentrations associated with acrylonitrile...... flame retardants (PBDEs and HBCD) identified in the plastic samples illustrates that circular material flows may be contaminated for extended periods. The screening clearly showed a need for improved documentation and monitoring of the presence of BFRs in plastic waste routed to recycling....

  18. [Influence of impurities on waste plastics pyrolysis: products and emissions].

    Science.gov (United States)

    Zhao, Lei; Wang, Zhong-Hui; Chen, De-Zhen; Ma, Xiao-Bo; Luan, Jian

    2012-01-01

    The study is aimed to evaluate the impact of impurities like food waste, paper, textile and especially soil on the pyrolysis of waste plastics. For this purpose, emissions, gas and liquid products from pyrolysis of waste plastics and impurities were studied, as well as the transfer of element N, Cl, S from the substrates to the pyrolysis products. It was found that the presence of food waste would reduce the heat value of pyrolysis oil to 27 MJ/kg and increase the moisture in the liquid products, therefore the food residue should be removed from waste plastics; and the soil, enhance the waste plastics' pyrolysis by improving the quality of gas and oil products. The presence of food residue, textile and paper leaded to higher gas emissions.

  19. Advances in modeling plastic waste pyrolysis processes

    Directory of Open Access Journals (Sweden)

    Y. Safadi, J. Zeaiter

    2014-01-01

    Full Text Available The tertiary recycling of plastics via pyrolysis is recently gaining momentum due to promising economic returns from the generated products that can be used as a chemical feedstock or fuel. The need for prediction models to simulate such processes is essential in understanding in depth the mechanisms that take place during the thermal or catalytic degradation of the waste polymer. This paper presents key different models used successfully in literature so far. Three modeling schemes are identified: Power-Law, Lumped-Empirical, and Population-Balance based equations. The categorization is based mainly on the level of detail and prediction capability from each modeling scheme. The data shows that the reliability of these modeling approaches vary with the degree of details the experimental work and product analysis are trying to achieve.

  20. A comprehensive waste collection cost model applied to post-consumer plastic packaging waste

    NARCIS (Netherlands)

    Groot, J.J.; Bing, X.; Bos-Brouwers, H.E.J.; Bloemhof, J.M.

    2014-01-01

    Post-consumer plastic packaging waste (PPW) can be collected for recycling via source separation or post-separation. In source separation, households separate plastics from other waste before collection, whereas in post-separation waste is separated at a treatment centre after collection. There are

  1. A comprehensive waste collection cost model applied to post-consumer plastic packaging waste

    NARCIS (Netherlands)

    Groot, J.J.; Bing, X.; Bos-Brouwers, H.E.J.; Bloemhof, J.M.

    2014-01-01

    Post-consumer plastic packaging waste (PPW) can be collected for recycling via source separation or post-separation. In source separation, households separate plastics from other waste before collection, whereas in post-separation waste is separated at a treatment centre after collection. There are

  2. Sustainable reverse logistics for household plastic waste

    NARCIS (Netherlands)

    Bing, X.

    2014-01-01

    Summary of the thesis titled “Sustainable Reverse Logistics for Household Plastic Waste” PhD Candidate: Xiaoyun Bing Recycled plastic can be used in the manufacturing of plastic products to reduce the use of virgin plastics material. The cost of recycled plastics is usually lower than th

  3. Sustainable reverse logistics for household plastic waste

    NARCIS (Netherlands)

    Bing, X.

    2014-01-01

    Summary of the thesis titled “Sustainable Reverse Logistics for Household Plastic Waste” PhD Candidate: Xiaoyun Bing Recycled plastic can be used in the manufacturing of plastic products to reduce the use of virgin plastics material. The cost of recycled plastics is usually lower than

  4. Sustainable reverse logistics for household plastic waste

    NARCIS (Netherlands)

    Bing, X.

    2014-01-01

    Summary of the thesis titled “Sustainable Reverse Logistics for Household Plastic Waste” PhD Candidate: Xiaoyun Bing Recycled plastic can be used in the manufacturing of plastic products to reduce the use of virgin plastics material. The cost of recycled plastics is usually lower than th

  5. Synthesis of carbon nanotubes from waste polyethylene plastics

    Science.gov (United States)

    Zhuo, Chuanwei

    Generation of non-biodegradable wastes, such as plastics, and resulting land as well as water pollution therefrom discarded plastics have been continuously increasing, while landfill space decreases and recycling markets dwindle. Exploration of novel uses of such materials becomes therefore imperative. Here I present an innovative and unique partial conversion of plastic waste to valuable carbon nanomaterials. It is an overall exothermic and scalable process based on feeding waste plastics to a multi-stage, pyrolysis/combustion-synthesis reactor. Plain stainless steel screens are used as substrates as well as low-cost catalyst for both carbon nanomaterials synthesis and pyrolyzates generation. Nano carbon yields of as high as 13.6% of the weight of the polymer precursor were recorded. This demonstration provides a sustainable solution to both plastic waste utilization, and carbon nanomaterials mass production.

  6. Application of fluidization to separate packaging waste plastics.

    Science.gov (United States)

    Carvalho, M Teresa; Ferreira, Célia; Portela, Antía; Santos, João Tiago

    2009-03-01

    The objective of the experimental work described in this paper is the study of the separation of PS (polystyrene) from PET (polyethylene terephthalate) and PVC (polyvinyl chloride) from drop-off points using a fluidized bed separator. This is a low-cost process commonly used in the hydro-classification of mineral ores. Firstly, experimental tests were carried out with artificial granulated samples with different grain sizes, types and sources of plastic ("separability tests"). The particle settling velocities were determined under different operating conditions. Then, based on the results, the laboratory tests continued with real mixtures of waste plastics ("separation tests") and the efficiency of the process was evaluated. From a PET-rich mixture, a concentrate of PS with a 75% grade in PS was produced while the underflow was quite clear from PS (grade less than 0.5% in PS).

  7. Recycling of plastic waste: Presence of phthalates in plastics from households and industry.

    Science.gov (United States)

    Pivnenko, K; Eriksen, M K; Martín-Fernández, J A; Eriksson, E; Astrup, T F

    2016-08-01

    Plastics recycling has the potential to substitute virgin plastics partially as a source of raw materials in plastic product manufacturing. Plastic as a material may contain a variety of chemicals, some potentially hazardous. Phthalates, for instance, are a group of chemicals produced in large volumes and are commonly used as plasticisers in plastics manufacturing. Potential impacts on human health require restricted use in selected applications and a need for the closer monitoring of potential sources of human exposure. Although the presence of phthalates in a variety of plastics has been recognised, the influence of plastic recycling on phthalate content has been hypothesised but not well documented. In the present work we analysed selected phthalates (DMP, DEP, DPP, DiBP, DBP, BBzP, DEHP, DCHP and DnOP) in samples of waste plastics as well as recycled and virgin plastics. DBP, DiBP and DEHP had the highest frequency of detection in the samples analysed, with 360μg/g, 460μg/g and 2700μg/g as the maximum measured concentrations, respectively. Among other, statistical analysis of the analytical results suggested that phthalates were potentially added in the later stages of plastic product manufacturing (labelling, gluing, etc.) and were not removed following recycling of household waste plastics. Furthermore, DEHP was identified as a potential indicator for phthalate contamination of plastics. Close monitoring of plastics intended for phthalates-sensitive applications is recommended if recycled plastics are to be used as raw material in production.

  8. Oil sorbents from plastic wastes and polymers: A review.

    Science.gov (United States)

    Saleem, Junaid; Adil Riaz, Muhammad; Gordon, McKay

    2018-01-05

    A large volume of the waste produced across the world is composed of polymers from plastic wastes such as polyethylene (HDPE or LDPE), polypropylene (PP), and polyethylene terephthalate (PET) amongst others. For years, environmentalists have been looking for various ways to overcome the problems of such large quantities of plastic wastes being disposed of into landfill sites. On the other hand, the usage of synthetic polymers as oil sorbents in particular, polyolefins, including polypropylene (PP) and polyethylene (PE) have been reported. In recent years, the idea of using plastic wastes as the feed for the production of oil sorbents has gained momentum. However, the studies undertaking such feasibility are rather scattered. This review paper is the first of its kind reporting, compiling and reviewing these various processes. The production of an oil sorbent from plastic wastes is being seen to be satisfactorily achievable through a variety of methods Nevertheless, much work needs to be done regarding further investigation of the numerous parameters influencing production yields and sorbent qualities. For example, differences in results are seen due to varying operating conditions, experimental setups, and virgin or waste plastics being used as feeds. The field of producing oil sorbents from plastic wastes is still very open for further research, and seems to be a promising route for both waste reduction, and the synthesis of value-added products such as oil sorbents. In this review, the research related to the production of various oil sorbents based on plastics (plastic waste and virgin polymer) has been discussed. Further oil sorbent efficiency in terms of oil sorption capacity has been described. Copyright © 2017 Elsevier B.V. All rights reserved.

  9. Pyrolysis of plastic packaging waste: A comparison of plastic residuals from material recovery facilities with simulated plastic waste.

    Science.gov (United States)

    Adrados, A; de Marco, I; Caballero, B M; López, A; Laresgoiti, M F; Torres, A

    2012-05-01

    Pyrolysis may be an alternative for the reclamation of rejected streams of waste from sorting plants where packing and packaging plastic waste is separated and classified. These rejected streams consist of many different materials (e.g., polyethylene (PE), polypropylene (PP), polystyrene (PS), polyvinyl chloride (PVC), polyethylene terephthalate (PET), acrylonitrile butadiene styrene (ABS), aluminum, tetra-brik, and film) for which an attempt at complete separation is not technically possible or economically viable, and they are typically sent to landfills or incinerators. For this study, a simulated plastic mixture and a real waste sample from a sorting plant were pyrolyzed using a non-stirred semi-batch reactor. Red mud, a byproduct of the aluminum industry, was used as a catalyst. Despite the fact that the samples had a similar volume of material, there were noteworthy differences in the pyrolysis yields. The real waste sample resulted, after pyrolysis, in higher gas and solid yields and consequently produced less liquid. There were also significant differences noted in the compositions of the compared pyrolysis products.

  10. Use of waste plastic in construction of bituminous road

    Directory of Open Access Journals (Sweden)

    Abhijeet Jirge

    2012-05-01

    Full Text Available Bottles, containers and packing strips etc. is increasing day by day. As a result amount of waste plastic also increases. This leads to various environmental problems. Many of the wastes produced today will remain in the environment for many years leading to various environmental concerns. Therefore it is necessary to utilize thewastes effectively with technical development in each field. Many by-products are being produced using the plastic wastes. Our present work is helping to take care of these aspects. Plastic waste, consisting of carry bags, cups and other utilized plastic can be used as a coating over aggregate and this coated stone can be used for roadconstruction. The mix polymer coated aggregate and tyre modified bitumen have shown higher strength. Use of this mix for road construction helps to use plastics waste. Once the plastic waste is separated from municipal solid waste, the organic matter can be converted into manure and used. Our paper will discuss in detail theprocess and its successful applications.

  11. Flash Cracking Reactor for Waste Plastic Processing Project

    Data.gov (United States)

    National Aeronautics and Space Administration — We propose to design, model, build, and test a novel flash cracking reactor to convert plastic waste, and potentially other unconventional hydrocarbon feedstocks,...

  12. Stress-strain response of plastic waste mixed soil.

    Science.gov (United States)

    Babu, G L Sivakumar; Chouksey, Sandeep Kumar

    2011-03-01

    Recycling plastic waste from water bottles has become one of the major challenges worldwide. The present study provides an approach for the use plastic waste as reinforcement material in soil. The experimental results in the form of stress-strain-pore water pressure response are presented. Based on experimental test results, it is observed that the strength of soil is improved and compressibility reduced significantly with addition of a small percentage of plastic waste to the soil. The use of the improvement in strength and compressibility response due to inclusion of plastic waste can be advantageously used in bearing capacity improvement and settlement reduction in the design of shallow foundations. Copyright © 2010 Elsevier Ltd. All rights reserved.

  13. Serbia: A new process for waste rubber and plastic recycling

    Directory of Open Access Journals (Sweden)

    Ozren Ocic

    2010-02-01

    Full Text Available This paper intends to describe a new technological process for waste rubber and plastic recycling up to the commercial components in safe environmental friendly way. Researches and all relevant technical-technological data related to this process are checked at constructed pilot plant. The future construction of these units for waste rubber and plastic recycling will allow interested parties to achieve the environmental effectiveness and economic efficiency.

  14. Sustainable reverse logistics network design for household plastic waste

    NARCIS (Netherlands)

    Bing, X.; Bloemhof, J.M.; Vorst, van der J.G.A.J.

    2014-01-01

    Plastic recycling is a legal requirement and can yield environmental benefits. In the Netherlands, there is a complex network of various collection methods, separation centers, sorting centers and reprocessors. The first step of the recycling system, separating plastics from other waste, can occur w

  15. Sustainable reverse logistics network design for household plastic waste

    NARCIS (Netherlands)

    Bing, X.; Bloemhof, J.M.; Vorst, van der J.G.A.J.

    2014-01-01

    Plastic recycling is a legal requirement and can yield environmental benefits. In the Netherlands, there is a complex network of various collection methods, separation centers, sorting centers and reprocessors. The first step of the recycling system, separating plastics from other waste, can occur

  16. Assessment of plastic waste generation and its potential recycling of household solid waste in Can Tho City, Vietnam.

    Science.gov (United States)

    Thanh, Nguyen Phuc; Matsui, Yasuhiro; Fujiwara, Takeshi

    2011-04-01

    Plastic solid waste has become a serious problem when considering the disposal alternatives following the sequential hierarchy of sound solid waste management. This study was undertaken to assess the quantity and composition of household solid waste, especially plastic waste to identify opportunities for waste recycling. A 1-month survey of 130 households was carried out in Can Tho City, the capital city of the Mekong Delta region in southern Vietnam. Household solid waste was collected from each household and classified into ten physical categories; especially plastic waste was sorted into 22 subcategories. The average household solid waste generation rate was 281.27 g/cap/day. The compostable and recyclable shares respectively accounted for high percentage as 80.74% and 11%. Regarding plastic waste, the average plastic waste generation rate was 17.24 g/cap/day; plastic packaging and plastic containers dominated with the high percentage, 95.64% of plastic waste. Plastic shopping bags were especially identified as the major component, accounting for 45.72% of total plastic waste. Relevant factors such as household income and household size were found to have an existing correlation to plastic waste generation in detailed composition. The household habits and behaviors of plastic waste discharge and the aspects of environmental impacts and resource consumption for plastic waste disposal alternatives were also evaluated.

  17. Catalytic plastics cracking for recovery of gasoline-range hydrocarbons from municipal plastic wastes

    Energy Technology Data Exchange (ETDEWEB)

    Buekens, A.G.; Huang, H. [Department of Chemical Engineering and Industrial Chemistry - CHIS 2, Free University of Brussels, Pleinlaan 2, Brussels 1050 (Belgium)

    1998-08-01

    This paper reviews recent developments in plastics cracking, a process developed to recycle plastic wastes into useful petrochemical materials. Under thermal cracking conditions, plastic wastes can be decomposed into three fractions: gas, liquid and solid residue. The liquid products are usually composed of higher boiling point hydrocarbons. By adopting customary fluid cracking catalysts and reforming catalysts, more aromatics and naphthenes in the C{sub 6}-C{sub 8} range can be produced, which are valuable gasoline-range hydrocarbons. More tests are, however, needed to verify the pyrolysis process in a pilot scale particularly for treatment of mixtures of bulk plastics. Plastics cracking is only an elementary conversion technology; its application has to be combined with other technologies such as municipal solid waste collection, classification and pretreatment at the front end, as well as hydrocarbon distillation and purification at the back end. Social, environmental and economic factors are also important in industrial implementation of the technology

  18. Preparing Attitude Scale to Define Students' Attitudes about Environment, Recycling, Plastic and Plastic Waste

    Science.gov (United States)

    Avan, Cagri; Aydinli, Bahattin; Bakar, Fatma; Alboga, Yunus

    2011-01-01

    The aim of this study is to introduce an attitude scale in order to define students? attitudes about environment, recycling, plastics, plastic waste. In this study, 80 attitude sentences according to 5-point Likert-type scale were prepared and applied to 492 students of 6th grade in the Kastamonu city center of Turkey. The scale consists of…

  19. TRANSPORT PLANNING MODEL FOR WIDE AREA RECYCLING SYSTEM OF INDUSTRIAL WASTE PLASTIC

    Science.gov (United States)

    Arai, Yasuhiro; Kawamura, Hisashi; Koizumi, Akira; Mogi, Satoshi

    To date, the majority of industrial waste plastic generated in an urban city has been processed into landfill. However, it is now necessary to actively utilize that plastic as a useful resource to create a recycling society with a low environment influence. In order to construct a reasonable recycling system, it is necessary to address the "transportation problem," which means determining how much industrial waste plastic is to be transported to what location. With the goal of eliminating landfill processing, this study considers a transport planning model for industrial waste plastic applying linear programming. The results of running optimized calculations under given scenarios clarified not only the possibilities for recycle processing in the Metropolitan area, but also the validity of wide area recycling system.

  20. Supercritical Water Process for the Chemical Recycling of Waste Plastics

    Science.gov (United States)

    Goto, Motonobu

    2010-11-01

    The development of chemical recycling of waste plastics by decomposition reactions in sub- and supercritical water is reviewed. Decomposition reactions proceed rapidly and selectively using supercritical fluids compared to conventional processes. Condensation polymerization plastics such as PET, nylon, and polyurethane, are relatively easily depolymerized to their monomers in supercritical water. The monomer components are recovered in high yield. Addition polymerization plastics such as phenol resin, epoxy resin, and polyethylene, are also decomposed to monomer components with or without catalysts. Recycling process of fiber reinforced plastics has been studied. Pilot scale or commercial scale plants have been developed and are operating with sub- and supercritical fluids.

  1. Recycling of plastic waste: Screening for brominated flame retardants (BFRs).

    Science.gov (United States)

    Pivnenko, K; Granby, K; Eriksson, E; Astrup, T F

    2017-08-30

    Flame retardants are chemicals vital for reducing risks of fire and preventing human casualties and property losses. Due to the abundance, low cost and high performance of bromine, brominated flame retardants (BFRs) have had a significant share of the market for years. Physical stability on the other hand, has resulted in dispersion and accumulation of selected BFRs in the environment and receiving biota. A wide range of plastic products may contain BFRs. This affects the quality of waste plastics as secondary resource: material recycling may potentially reintroduce the BFRs into new plastic product cycles and lead to increased exposure levels, e.g. through use of plastic packaging materials. To provide quantitative and qualitative data on presence of BFRs in plastics, we analysed bromophenols (tetrabromobisphenol A (TBBPA), dibromophenols (2,4- and 2,6-DBP) and 2,4,6-tribromophenol (2,4,6-TBP)), hexabromocyclododecane stereoisomers (α-, β-, and γ-HBCD), as well as selected polybrominated diphenyl ethers (PBDEs) in samples of household waste plastics, virgin and recycled plastics. A considerable number of samples contained BFRs, with highest concentrations associated with acrylonitrile butadiene styrene (ABS, up to 26,000,000ngTBBPA/g) and polystyrene (PS, up to 330,000ng∑HBCD/g). Abundancy in low concentrations of some BFRs in plastic samples suggested either unintended addition in plastic products or degradation of higher molecular weight BFRs. The presence of currently restricted flame retardants (PBDEs and HBCD) identified in the plastic samples illustrates that circular material flows may be contaminated for extended periods. The screening clearly showed a need for improved documentation and monitoring of the presence of BFRs in plastic waste routed to recycling. Copyright © 2017. Published by Elsevier Ltd.

  2. XRF Determination of the 8 Elements in the Coating of Waste Plastics%X射线荧光光谱法测定废塑料表面涂层中8种元素的含量

    Institute of Scientific and Technical Information of China (English)

    黄世杰; 张建波; 应海松; 蔡曹盛; 李雪莲

    2016-01-01

    采用 X 射线荧光光谱法测定废塑料表面涂层中8种元素的含量。考察了样品杯、基材以及金属涂层中元素效应对检测结果的影响。P、Si、Fe、Pb、Al、Cu、Cr 和 Ni 的测定范围在0.002%~52.0%之间,检出限在0.0002%~0.0008%之间。采用本方法测定废塑料样品表面涂层中元素含量,结果与 ICP-AES 测定结果一致,测定值的相对标准偏差(n=7)小于1%。%X-ray fluorescence spectrometry was applied to the determination of 8 elements in the coating of waste plastics.The effects of the sample cup and the elements in the matrixes and the coating on the determination results were discussed.The determination ranges of P,Si,Fe,Pb,Al,Cu,Cr and Ni were between 0.002%-52.0%,and the detection limits were in the range of 0.000 2%-0.000 8%.The proposed method was used to determine 8 elements in the coating of waste plastic samples,giving results in agreement with those obtained by ICP-AES,with RSDs (n=7)less than 1%.

  3. Small WEEE: determining recyclables and hazardous substances in plastics.

    Science.gov (United States)

    Dimitrakakis, Emmanouil; Janz, Alexander; Bilitewski, Bernd; Gidarakos, Evangelos

    2009-01-30

    An examination regarding the determination of recyclables and hazardous substances in small waste electrical and electronic equipment (WEEE) found in the residual household waste stream of the city of Dresden, Germany, is described. Firstly, attitudes towards the disposal of small WEEE in the latter are assessed, and product types and categories which mostly contribute to its composition are identified. Physical parameters which could be used as mechanical sorting criteria are measured, and the material composition of the small WEEE found is determined. The hazardous substances' "base" charge in the residual waste is established by means of atomic absorption spectrometry and ionic chromatography, as a first step in estimating the contribution of small WEEE to its pollutant load. Consequently, the content of small WEEE plastics in key heavy metals and halogens is determined. Key conclusions are drawn concerning the future strategic development and practical implementation of the 2002/96/EC Directive, in relation to small WEEE management and recycling.

  4. XRFS Determinate of metallic coating content of waste plastics%X-射线荧光光谱法测定废塑料表面金属涂层含量

    Institute of Scientific and Technical Information of China (English)

    黄世杰; 张建波; 应海松; 李雪莲

    2015-01-01

    本文提出了利用X-荧光仪测定废塑料各种金属涂层中金属元素含量的方法。以稳定性为优化原则选择了仪器针对不同元素的测量条件,研究了实验过程中样品杯、基材以及金属涂层中元素效应对检测结果的影响;方法精密度为0.008%~0.044%之间;将X-荧光检测结果与ICP检测结果进行比对并得出同样的数据,该方法为控制废塑料金属涂层产生的危害和污染提供更为合理的检测手段,并已应用到实际检测当中。%A new method for determining every metal elements in the metallic coating of waste plastics by X-ray fluorescence spectrometer was bronght out. The instrument working conditions for different elements were opti-mized according to the stability, the effects of sample cup,base material and matrix elements for the determinated results were discussed;RSDs were in the range of 0.5%~1.5%, The results were given indifferent by XRFS and ICP-OES were compared and gave uniformity results. This method can give more reasonable results for controlling dam-age and contamination by metallic coating of waste plastics. It also has been applied to practical sample analysis.

  5. Recycling of plastic waste by density separation: prospects for optimization.

    Science.gov (United States)

    Gent, Malcolm Richard; Menendez, Mario; Toraño, Javier; Diego, Isidro

    2009-03-01

    A review of existing industrial processing and results of alternative processing investigations for separating solid mixtures and specifically recycling plastic waste by density separation is presented. Media density separation is shown to be fundamental for separation and/or pre-concentration in the recycling of plastics. The current use of static media processes limits the capacity and size of material that can be treated commercially. Investigations have shown that the hydroscopic properties of plastics can be reduced to improve such separations. This indicates that an alternative processing method is required to increase the commercial recovery of recyclable plastics. Cylindroconical and cylindrical cyclone-type media separators, such as those used for processing coal, are reviewed and suggested as a potential substitute. Both have superior production capacities and are able to process a larger range in particle sizes treated. A summary of results of investigations with cyclone media devices for recycling plastics is presented.

  6. Design and construction of prestressed arch using plastic shoppers waste

    Directory of Open Access Journals (Sweden)

    Ali Khan, S.

    2012-12-01

    Full Text Available Since the development of plastic in the last century, being versitile it has become very popular for diversified uses. The problem appears when these plastics, particularly shoppers are disposed as waste. The current reuse and recycling rates for the plastic shoppers waste are very low. Construction Industry has a great potential for the reuse of shoppers waste. Shoppers waste has been compressed to fabricate compressed shoppers waste (CSW blocks. This study is related to an innovative reuse of CSW-blocks for the construction of prestressed structural arch. This paper is dedicated to the design and construction of structural arch using shoppers waste as a material.

    Desde su desarrollo durante el siglo pasado y debido a su versatilidad, el plástico se ha hecho ubicuo en la sociedad actual. Los problemas surgen cuando este material, sobre todo cuando conforma bienes de consumo, se desecha. Actualmente, los índices de valorización y reciclado de residuos plásticos de origen doméstico son muy bajos. El sector de la construcción tiene una enorme potencial para reutilizar este tipo de residuos, que se pueden comprimir para fabricar bloques. Este artículo presenta un uso innovador de los bloques de residuos plásticos: la construcción de un arco estructural pretesado. Describe el proyecto y la ejecución de un arco estructural construido con estos materiales de desecho.

  7. Separate collection of plastic waste, better than technical sorting from municipal solid waste?

    Science.gov (United States)

    Feil, Alexander; Pretz, Thomas; Jansen, Michael; Thoden van Velzen, Eggo U

    2017-02-01

    The politically preferred solution to fulfil legal recycling demands is often implementing separate collection systems. However, experience shows their limitations, particularly in urban centres with a high population density. In response to the European Union landfill directive, mechanical biological waste treatment plants have been installed all over Europe. This technology makes it possible to retrieve plastic waste from municipal solid waste. Operators of mechanical biological waste treatment plants, both in Germany and the Netherlands, have started to change their mechanical separation processes to additionally produce plastic pre-concentrates. Results from mechanical biological waste treatment and separate collection of post-consumer packaging waste will be presented and compared. They prove that both the yield and the quality of plastic waste provided as feedstock for the production of secondary plastic raw material are largely comparable. An economic assessment shows which conditions for a technical sorting plant are economically attractive in comparison to separate collection systems. It is, however, unlikely that plastic recycling will ever reach cost neutrality.

  8. Chemical recycle of plastics waste; Hai purasuchikku no kemikaru risaikuru

    Energy Technology Data Exchange (ETDEWEB)

    Miyake, A. [Sumitomo Chemical Co. Ltd., Osaka (Japan)

    1997-11-01

    Chemical recycling of the wasted plastics contains from regeneration to monomer as a constructing component in the case of single element polymer to conversion to fuel oil through thermal decomposition of the mixed wasted plastics and application to chemical raw material. Polymethyl methacrylate (PMMA) decomposes to methylmethacrylate (MMA) monomer with high selection rate at max temperature of 400{+-}50degC. The Mitsubishi Rayon Co., Ltd. Signed a cooperative development contract on the recycling technique of PMMA The ICI., Ltd., Great Britain. Depolymerization technique of Polyethylene terephthalate (PET) is already used actually on methanolysis with Coca-Cola Corp. (Hoechst-Celanese Corp.) and glycolysis with Pepsi-Cola Corp. (Goodyear Inc.). The chemical recycle due to thermal decomposition of the mixed wasted plastics is established as a technique of gasification of the mixed wasted plastics to generate methanol in Japan by the Mitsubishi Heavy Ind., Ltd., and is operated in a pilot plant of 2 ton/day. Here was summarized on these trends in and out of Japan. 29 refs., 5 figs., 4 tab.

  9. Low temperature conversion of plastic waste into light hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Shah, Sajid Hussain; Khan, Zahid Mahmood; Raja, Iftikhar Ahmad; Mahmood, Qaisar; Bhatti, Zulfiqar Ahmad; Khan, Jamil; Farooq, Ather; Rashid, Naim [Department of Environmental Sciences, COMSATS Institute of Information Technology, Abbottabad 22060 (Pakistan); Wu, Donglei, E-mail: wudl@zju.edu.cn [Department of Environmental Engineering, Zhejiang University, Hangzhou 310029 (China)

    2010-07-15

    Advance recycling through pyrolytic technology has the potential of being applied to the management of plastic waste (PW). For this purpose 1 l volume, energy efficient batch reactor was manufactured locally and tested for pyrolysis of waste plastic. The feedstock for reactor was 50 g waste polyethylene. The average yield of the pyrolytic oil, wax, pyrogas and char from pyrolysis of PW were 48.6, 40.7, 10.1 and 0.6%, respectively, at 275 deg. C with non-catalytic process. Using catalyst the average yields of pyrolytic oil, pyrogas, wax and residue (char) of 50 g of PW was 47.98, 35.43, 16.09 and 0.50%, respectively, at operating temperature of 250 deg. C. The designed reactor could work at low temperature in the absence of a catalyst to obtain similar products as for a catalytic process.

  10. The waste-to-energy framework for integrated multi-waste utilization: Waste cooking oil, waste lubricating oil, and waste plastics

    Energy Technology Data Exchange (ETDEWEB)

    Singhabhandhu, Ampaitepin; Tezuka, Tetsuo [Energy Economics Laboratory, Department of Socio-Environmental Energy Science, Graduate School of Energy Science, Kyoto University, Yoshida-honmachi, Sakyo-ku, Kyoto 606-8501 (Japan)

    2010-06-15

    Energy generation by wastes is considered one method of waste management that has the benefit of energy recovery. From the waste-to-energy point of view, waste cooking oil, waste lubricating oil, and waste plastics have been considered good candidates for feedstocks for energy conversion due to their high heating values. Compared to the independent management of these three wastes, the idea of co-processing them in integration is expected to gain more benefit. The economies of scale and the synergy of co-processing these wastes results in higher quality and higher yield of the end products. In this study, we use cost-benefit analysis to evaluate the integrated management scenario of collecting the three wastes and converting them to energy. We report the total heat of combustion of pyrolytic oil at the maximum and minimum conversion rates, and conduct a sensitivity analysis in which the parameters of an increase of the electricity cost for operating the process and increase of the feedstock transportation cost are tested. We evaluate the effects of economy of scale in the case of integrated waste management. We compare four cases of waste-to-energy conversion with the business as usual (BAU) scenario, and our results show that the integrated co-processing of waste cooking oil, waste lubricating oil, and waste plastics is the most profitable from the viewpoints of energy yield and economics. (author)

  11. Contribution of plastic waste recovery to greenhouse gas (GHG) savings in Spain

    OpenAIRE

    Sevigné Itoiz, Eva; Martínez Gasol, Carles; Rieradevall, Joan; Gabarrell Durany, Xavier

    2015-01-01

    This paper concentrates on the quantification of greenhouse gas (GHG) emissions of post-consumer plastic waste recovery (material or energy) by considering the influence of the plastic waste quality (high or low), the recycled plastic applications (virgin plastic substitution or non-plastic substitution) and the markets of recovered plastic (regional or global). The aim is to quantify the environmental consequences of different alternatives in order to evaluate opportunities and limitations t...

  12. Electrical separation of plastics coming from special waste.

    Science.gov (United States)

    Gente, Vincenzo; La Marca, Floriana; Lucci, Federica; Massacci, Paolo

    2003-01-01

    Minimisation of waste to landfilling is recognised as a priority in waste management by European rules. In order to achieve this goal, developing suitable technologies for waste recycling is therefore of great importance. To achieve this aim the technologies utilised for mineral processing can be taken into consideration to develop recycling systems. In particular comminution and separation processes can be adopted to recover valuable materials from composite waste. In this work the possibility of recycling pharmaceutical blister packaging has been investigated. A suitable comminution process has been applied in order to obtain the liberation of the plastic and aluminium components. Experiments of electrical separation have been carried out in order to point out the influence of the process parameters on the selections of the different materials and to set up the optimum operating conditions.

  13. Hydrocarbon composition products of the catalytic recycling plastics waste

    Directory of Open Access Journals (Sweden)

    Zhaksyntay Kairbekov

    2013-09-01

    Full Text Available The paper represents the IR spectroscopy results of the hydrocarbon composition of products, which is obtained from catalytic processing of plastic wastes. The optimal conditions for the hydrogenation with to producny liquid of products are identified.  These liquid products are enriched with aromatics, paraffinic- naphthenic and unsaturated hydrocarbons. The main characteristics of the distillates received by hydrogenation of plastics (as density, refractive index, iodine number, pour point, cloud point, filtering, sulfur content,  fractional and composition of the hydrocarbon group.

  14. Enhancing anti-microbial properties of wood-plastic composites produced from timber and plastic wastes.

    Science.gov (United States)

    Wang, Lei; Chen, Season S; Tsang, Daniel C W; Poon, Chi Sun; Ok, Yong Sik

    2017-05-01

    Considering the resource waste and environmental burden for timber and plastic materials ending up at landfills, this study proposed upcycling wood and plastic waste into value-added wood-plastic composites (WPCs), complying with the standard requirements of flexural strength, thickness swelling, water absorption and thermal insulation. Biological deterioration is a major concern of WPCs. Bacterial survival, fungal attack and algal growth of bactericide-treated WPCs were holistically analysed. Melamine resin was adopted for impregnating anti-microbial agents on the surface. All the agents showed excellent bactericidal rate (Escherichia coli), yet poly-diallyl-dimethyl-ammonium chloride (PolyDADMAC) and silver had the lowest minimum inhibitory concentrations. In terms of weight loss and strength reduction due to fungal decay (Coriolus versicolor), PolyDADMAC, silver and cetyltrimethylammonium bromide (CTAB) imparted the highest resistance on the WPCs. Moreover, PolyDADMAC and copper provided the most protection against algal growth (Chlorella vulgaris), and the former presented durable inhibitory effect. This study presents a value-added solution to wood/plastic waste recycling.

  15. The impact of policy interactions on the recycling of plastic packaging waste in Germany

    OpenAIRE

    Gandenberger, Carsten; Orzanna, Robert; Klingenfuß, Sara; Sartorius, Christian

    2014-01-01

    Due to the environmental challenges associated with the strong growth of plastic waste worldwide, the EU Commission recently published a green paper on a European Strategy on Plastic Waste in the Environment (COM (2013), 123 final), which highlights the challenges and opportunities that arise from improving the management of plastic waste in the EU. The European Waste Directive (2008/98/EC) which was transposed into German law through the Kreislaufwirtschaftsgesetz (KrWG) established the so-c...

  16. Integrated Index in Consideration of Appropriate Plastic Recycling System in Waste Bank Operation

    OpenAIRE

    Firdaus Pambudi Noorhan; Dowaki Kiyoshi; Adhiutama Akbar

    2016-01-01

    Several appropriate technology had been developed to maintain plastic waste in society according to minimize environmental impact. Landfill is no longer appropriate to maintain plastic waste based on the environmental impact that might be occurred for instance. However in developing countries such as Indonesia, although plastic recycling technology have been promoted by maintain waste bank policy for support community willingness to exchange their recyclable waste with certain monetary values...

  17. Technical specifications for mechanical recycling of agricultural plastic waste.

    Science.gov (United States)

    Briassoulis, D; Hiskakis, M; Babou, E

    2013-06-01

    Technical specifications appropriate for the recycling of agricultural plastic wastes (APWs), widely accepted by the recycling industry were developed. The specifications establish quality standards to be met by the agricultural plastics producers, users and the agricultural plastic waste management chain. They constitute the base for the best economical and environmental valorisation of the APW. The analysis of the APW streams conducted across Europe in the framework of the European project "LabelAgriWaste" revealed the inherent characteristics of the APW streams and the inherent constraints (technical or economical) of the APW. The APW stream properties related to its recycling potential and measured during pilot trials are presented and a subsequent universally accepted simplified and expanded list of APW recycling technical specifications is proposed and justified. The list includes two sets of specifications, applied to two different quality categories of recyclable APW: one for pellet production process ("Quality I") and another one for plastic profile production process ("Quality II"). Parameters that are taken into consideration in the specifications include the APW physical characteristics, contamination, composition and degradation. The proposed specifications are focused on polyethylene based APW that represents the vast majority of the APW stream. However, the specifications can be adjusted to cover also APW of different materials (e.g. PP or PVC) that are found in very small quantities in protected cultivations in Europe. The adoption of the proposed specifications could transform this waste stream into a labelled commodity traded freely in the market and will constitute the base for the best economical and environmental valorisation of the APW.

  18. Operating room waste reduction in plastic and hand surgery

    Science.gov (United States)

    Albert, Mark G; Rothkopf, Douglas M

    2015-01-01

    BACKGROUND: Operating rooms (ORs), combined with labour and delivery suites, account for approximately 70% of hospital waste. Previous studies have reported that recycling can have a considerable financial impact on a hospital-wide basis; however, its importance in the OR has not been demonstrated. OBJECTIVE: To propose a method of decreasing cost through judicious selection of instruments and supplies, and initiation of recycling in plastic and hand surgery. METHODS: The authors identified disposable supplies and instruments that are routinely opened and wasted in common plastic and hand surgery procedures, and calculated the savings that can result from eliminating extraneous items. A cost analysis was performed, which compared the expense of OR waste versus single-stream recycling and the benefit of recycling HIPAA documents and blue wrap. RESULTS: Fifteen total items were removed from disposable plastic packs and seven total items from hand packs. A total of US$17,381.05 could be saved per year from these changes alone. Since initiating single-stream recycling, the authors’ institution has saved, on average, US$3,487 per month at the three campuses. After extrapolating at the current savings rate, one would expect to save a minimum of US$41,844 per year. DISCUSSION: OR waste reduction is an effective method of decreasing cost in the surgical setting. By revising the contents of current disposable packs and instrument sets designated for plastic and hand surgery, hospitals can reduce the amount of opened and unused material. CONCLUSIONS: Significant financial savings and environmental benefit can result from this judicious supply and instrument selection, as well as implementation of recycling. PMID:26665137

  19. Characterization of ecofriendly polyethylene fiber from plastic bag waste

    Science.gov (United States)

    Soekoco, Asril S.; Noerati, Komalasari, Maya; Kurniawan, Hananto, Agus

    2017-08-01

    This paper presents the characterization of fiber morphology, fiber count and tenacity of polyethylene fiber which is made from plastic bag waste. Recycling plastic bag waste into textile fiber has not developed yet. Plastic bag waste was recycled into fiber by melt spinning using laboratory scale melt spinning equipment with single orifice nozzle and plunger system. The basic principle of melt spinning is by melting materials and then extruding it through small orifice of a spinning nozzle to form fibers. Diameter and cross section shape of Recycled polyethylene fiber were obtained by using scanning electron microscope (SEM) instrumentation. Linear density of the recycled fiber were analyzed by calculation using denier and dTex formulation and The mechanical strength of the fibers was measured in accordance with the ASTM D 3379-75 standard. The cross section of recycled fiber is circular taking the shape of orifice. Fiber count of 303.75 denier has 1.84 g/denier tenacity and fiber count of 32.52 has 3.44 g/denier tenacity. This conditions is affected by the growth of polymer chain alignment when take-up axial velocity become faster. Recycled polyethylene fiber has a great potential application in non-apparel textile.

  20. Catalytic dry reforming of waste plastics from different waste treatment plants for production of synthesis gases.

    Science.gov (United States)

    Saad, Juniza Md; Williams, Paul T

    2016-12-01

    Catalytic dry reforming of mixed waste plastics, from a range of different municipal, commercial and industrial sources, were processed in a two-stage fixed bed reactor. Pyrolysis of the plastics took place in the first stage and dry (CO2) reforming of the evolved pyrolysis gases took place in the second stage in the presence of Ni/Al2O3 and Ni-Co/Al2O3 catalysts in order to improve the production of syngas from the dry reforming process. The results showed that the highest amount of syngas yield was obtained from the dry reforming of plastic waste from the agricultural industry with the Ni/Al2O3 catalyst, producing 153.67mmolsyngasg(-1)waste. The addition of cobalt metal as a promoter to the Ni/Al2O3 catalyst did not have a major influence on syngas yield. Overall, the catalytic-dry reforming of waste plastics from various waste treatment plants showed great potential towards the production of synthesis gases. Copyright © 2016 Elsevier Ltd. All rights reserved.

  1. Improving Public Health and Environment through Plastic Waste Management in Mumbai Metropolitan Region

    Directory of Open Access Journals (Sweden)

    Sanjay RODE

    2015-12-01

    Full Text Available The Mumbai Metropolitan Region is growing in terms of population, industry, educational and commercial units. The daily requirements of commodities and services by all units have increased fast. Plastic is used extensively for packing, protection and service of various commodities. The use of plastic is much higher by industry and households in region. In Brihan Mumbai Municipal Corporation, the density of population is higher. The concentration of small and large industries is more. Therefore the plastic use is much higher for different purposes. It leads to more waste of plastic. In Ulhasnagar Municipal Corporation, the population and industrial units are less. Therefore plastic waste is less generated. Theaters are generating less plastic waste in metropolitan region. The Brihan Mumbai Municipal Corporation (BMC and municipal corporations in Thane district will continuously generate more plastic waste in future. The Tobit regression model shows that plastic waste is positively co-related and statistically significant with pollution and industry in region. Therefore the comprehensive policies are required to reduce plastic waste. This is because plastic waste is affecting on the health of human being. It also affects negatively on soil, air and water. The entire food supply chain gets affected due to plastic waste. The water logging is common due to plastic waste in region. It chock ups the drainage system and it becomes the ground for mosquitoes. It further leads to dengue, malaria and other diseases in region. Municipal corporations must collect plastic in separate bins and process it. The plastic and e-waste can be utilized for road construction in region. All the policies will certainly help to reduce the plastic waste and maintain the clean environment in region.

  2. Utilization possibilities of hydrocarbon fractions obtained by waste plastic pyrolysis: energetic utilization and applications in polymer composites

    Energy Technology Data Exchange (ETDEWEB)

    Miskolczi, Norbert; Borsodi, Nikolett; Angyal, Andras [University of Pannonia, MOL Department of Hydrocarbon and Coal Processing (Hungary)], email: mnorbert@almos.uni-pannon.hu, email: borsodinikolett@almos.uni-pannon.hu, email: angyala@almos.uni-pannon.hu

    2011-07-01

    With the energy crisis and the rising concerns about the environment, energy-saving measures are urgently needed. Each year about 300M tons of plastic wastes are produced world-wide and governments are now focusing on recycling and reusing these products to save significant amounts of energy. The aim of this paper was to analyze the products which can be obtained from waste plastic and determine their possible uses. Pyrolysis of commercial waste plastics was done in a reactor at 500-600 degree celsius and the products were then analyzed using several methods. Results showed that the pyrolysis produces gases, naphtha, middle distillates and heavy oils. The properties of these products were also determined and it was found that they have the potential to be used in fuel-like and additive producing applications. This study highlighted that pyrolysis of waste polymers can yield useful products.

  3. A pyrolysis study for the thermal and kinetic characteristics of an agricultural waste with two different plastic wastes.

    Science.gov (United States)

    Çepelioğullar, Özge; Pütün, Ayşe E

    2014-10-01

    In this study, thermochemical conversion of plastic wastes (PET and PVC) together with an agricultural waste (hazelnut shell) was investigated. In order to determine the thermal and kinetic behaviours, pyrolysis experiments were carried out from room temperature to 800 °C, with a heating rate of 10 °C min(-1) in the presence of a N2 atmosphere in a thermogravimetric analyzer. With the obtained thermogravimetric data, an appropriate temperature was specified for the pyrolysis of biomass-plastic wastes in a fixed-bed reactor. At the second step, pyrolysis experiments were carried out at the same conditions with the thermogravimetric analyzer, except the final temperature which was up to 500 °C in this case. After pyrolysis experiments, pyrolysis yields were calculated and characterization studies for bio-oil were investigated. Experimental results showed that co-pyrolysis has an important role in the determination of the pyrolysis mechanism and the process conditions while designing/implementing a thermochemical conversion method where biomass-plastic materials were preferred as raw materials. © The Author(s) 2014.

  4. Performance of sand-lime products made with plastic waste

    Directory of Open Access Journals (Sweden)

    Nowek Milena

    2016-01-01

    Full Text Available The paper describes the studies on the sand-lime (silicate masonry units modified with recycled plastics in various forms: regranulate, regrind and powder. The following materials were examined: high impact polystyrene (HIPS and acrylonitrile butadiene styrene (ABS. The results of the functional properties tests, such as compressive strength, softening behavior, bulk density and water absorption are presented in the article. The microstructure of the products was analyzed using SEM and XRD methods.Obtained results show that the properties of modified product largely depend on the type, form and amount of used polymer. The highest compressive strength was achieved with 15% of HIPS regranulate in the product (by weight. ABS does not improve the strength of the sample, however, it does block the capillary action in the sand-lime product. The lowest softening coefficient was obtained in the sample modified with HIPS regranulate. The examined polymers contributed to decrease in bulk density of the samples as well as lowered their water absorption. The samples with pulverized polymer have the worst properties. All the results are compared with those of the traditional sand-lime bricks and sand-lime product modified with other additives. The analysis indicate that silicate masonry units with post-production and post-consumption plastic waste can possess interesting functional properties what brings a new potential possibility to dispose of still growing number of plastic waste.

  5. Forecasting waste compositions: A case study on plastic waste of electronic display housings.

    Science.gov (United States)

    Peeters, Jef R; Vanegas, Paul; Kellens, Karel; Wang, Feng; Huisman, Jaco; Dewulf, Wim; Duflou, Joost R

    2015-12-01

    Because of the rapid succession of technological developments, the architecture and material composition of many products used in daily life have drastically changed over the last decades. As a result, well-adjusted recycling technologies need to be developed and installed to cope with these evolutions. This is essential to guarantee continued access to materials and to reduce the ecological impact of our material consumption. However, limited information is currently available on the material composition of arising waste streams and even less on how these waste streams will evolve. Therefore, this paper presents a methodology to forecast trends in the material composition of waste streams. To demonstrate the applicability and value of the proposed methodology, it is applied to forecast the evolution of plastic housing waste from flat panel display (FPD) TVs, FPD monitors, cathode ray tube (CRT) TVs and CRT monitors. The results of the presented forecasts indicate that a wide variety of plastic types and additives, such as flame retardants, are found in housings of similar products. The presented case study demonstrates that the proposed methodology allows the identification of trends in the evolution of the material composition of waste streams. In addition, it is demonstrated that the recycling sector will need to adapt its processes to deal with the increasing complexity of plastics of end-of-life electronic displays while respecting relevant directives.

  6. Recycling and recovery of post-consumer plastic solid waste in a European context

    OpenAIRE

    Dewil Raf; Baeyens Jan; Brems Anke

    2012-01-01

    The disposal of waste plastics has become a major worldwide environmental problem. The USA, Europe and Japan generate annually about 50 million tons of post-consumer plastic waste, previously landfilled, generally considered as a non-sustainable and environmentally questionable option. Landfill sites and their capacity are, moreover, decreasing rapidly, and legislation is stringent. Several European Directives and US legislation concern plastic wastes and the required management. They a...

  7. Chemical compatibility screening results of plastic packaging to mixed waste simulants

    Energy Technology Data Exchange (ETDEWEB)

    Nigrey, P.J.; Dickens, T.G.

    1995-12-01

    We have developed a chemical compatibility program for evaluating transportation packaging components for transporting mixed waste forms. We have performed the first phase of this experimental program to determine the effects of simulant mixed wastes on packaging materials. This effort involved the screening of 10 plastic materials in four liquid mixed waste simulants. The testing protocol involved exposing the respective materials to {approximately}3 kGy of gamma radiation followed by 14 day exposures to the waste simulants of 60 C. The seal materials or rubbers were tested using VTR (vapor transport rate) measurements while the liner materials were tested using specific gravity as a metric. For these tests, a screening criteria of {approximately}1 g/m{sup 2}/hr for VTR and a specific gravity change of 10% was used. It was concluded that while all seal materials passed exposure to the aqueous simulant mixed waste, EPDM and SBR had the lowest VTRs. In the chlorinated hydrocarbon simulant mixed waste, only VITON passed the screening tests. In both the simulant scintillation fluid mixed waste and the ketone mixture simulant mixed waste, none of the seal materials met the screening criteria. It is anticipated that those materials with the lowest VTRs will be evaluated in the comprehensive phase of the program. For specific gravity testing of liner materials the data showed that while all materials with the exception of polypropylene passed the screening criteria, Kel-F, HDPE, and XLPE were found to offer the greatest resistance to the combination of radiation and chemicals.

  8. Tribo-charging properties of waste plastic granules in process of tribo-electrostatic separation.

    Science.gov (United States)

    Li, Jia; Wu, Guiqing; Xu, Zhenming

    2015-01-01

    Plastic products can be found everywhere in people's daily life. With the consistent growth of plastic consumption, more and more plastic waste is generated. Considering the stable chemical and physics characteristics of plastic, regular waste management methods are not suitable for recycling economic strategy of each government, which has become a serious environmental problem. Recycling plastic waste is considered to be the best way to treat it, because it cannot only deduce the waste but also save the energy to produce new virgin plastic. Tribo-electrostatic separation is strongly recommended for plastic separation as it can preserve the original properties of plastic and has little additional pollution. In this study, plastic granules are generated by crushing plastic waste in waste electric and electronic equipment. The tribo-charging properties of plastic waste were studied by vibrating tribo-charging and cyclone tribo-charging. The triboelectric series obtained by vibrating was: (-)-PE-PS-PC-PVC-ABS-PP-(+), while the triboelectric series obtained by cyclone was (-)-PE-PS-PC-PVC-ABS-PP-(+). Further, the cyclone charging was more effective and stable than vibrating charging. The impact factors experiments showed that small particle size was better changed than large ones and were more suitable recycled by tribo-electrostatic separation. High relative humidity was identified as impede charging effect. The results of this study will help defining the operating parameters of subsequent separator.

  9. New renewable source of energy from municipal solid waste plastics

    Energy Technology Data Exchange (ETDEWEB)

    Sarker, Moinuddin; Zaman, Ashiquz; Mamunor Rashid, Mohammad

    2010-09-15

    Renewable energy plays an important role in the supply of energy. When energy sources are used, the demand for fossil fuels is reduced. Emissions from the evaporation and combustion of these traditional fossil fuels contributing to a range of environmental and health problems, causing poor air quality, and emitting greenhouse gases that contribute to global warming. Alternative fuel created from domestic sources has been proposed as a solution to these problems and many alternative fuels are being developed based on solar, wind and biomass. Natural State Research has developed different alternative hydrocarbon fuel produced from abundant waste plastic materials.

  10. Pyrolytic Waste Plastic Oil and Its Diesel Blend: Fuel Characterization

    Science.gov (United States)

    Sultana, M.; Al-Mamun, M. R.; Hasan, M. R.

    2016-01-01

    The authors introduced waste plastic pyrolysis oil (WPPO) as an alternative fuel characterized in detail and compared with conventional diesel. High density polyethylene, HDPE, was pyrolyzed in a self-designed stainless steel laboratory reactor to produce useful fuel products. HDPE waste was completely pyrolyzed at 330–490°C for 2-3 hours to obtain solid residue, liquid fuel oil, and flammable gaseous hydrocarbon products. Comparison of the fuel properties to the petrodiesel fuel standards ASTM D 975 and EN 590 revealed that the synthetic product was within all specifications. Notably, the fuel properties included a kinematic viscosity (40°C) of 1.98 cSt, density of 0.75 gm/cc, sulphur content of 0.25 (wt%), and carbon residue of 0.5 (wt%), and high calorific value represented significant enhancements over those of conventional petroleum diesel fuel. PMID:27433168

  11. Pyrolytic Waste Plastic Oil and Its Diesel Blend: Fuel Characterization

    Directory of Open Access Journals (Sweden)

    M. Z. H. Khan

    2016-01-01

    Full Text Available The authors introduced waste plastic pyrolysis oil (WPPO as an alternative fuel characterized in detail and compared with conventional diesel. High density polyethylene, HDPE, was pyrolyzed in a self-designed stainless steel laboratory reactor to produce useful fuel products. HDPE waste was completely pyrolyzed at 330–490°C for 2-3 hours to obtain solid residue, liquid fuel oil, and flammable gaseous hydrocarbon products. Comparison of the fuel properties to the petrodiesel fuel standards ASTM D 975 and EN 590 revealed that the synthetic product was within all specifications. Notably, the fuel properties included a kinematic viscosity (40°C of 1.98 cSt, density of 0.75 gm/cc, sulphur content of 0.25 (wt%, and carbon residue of 0.5 (wt%, and high calorific value represented significant enhancements over those of conventional petroleum diesel fuel.

  12. Life cycle assessment of post-consumer plastics production from waste electrical and electronic equipment (WEEE) treatment residues in a Central European plastics recycling plant

    Energy Technology Data Exchange (ETDEWEB)

    Wäger, Patrick A., E-mail: patrick.waeger@empa.ch; Hischier, Roland

    2015-10-01

    Plastics play an increasingly important role in reaching the recovery and recycling rates defined in the European WEEE Directive. In a recent study we have determined the life cycle environmental impacts of post-consumer plastics production from mixed, plastics-rich WEEE treatment residues in the Central European plant of a market-leading plastics recycler, both from the perspective of the customers delivering the residues and the customers buying the obtained post-consumer recycled plastics. The results of our life cycle assessments, which were extensively tested with sensitivity analyses, show that from both perspectives plastics recycling is clearly superior to the alternatives considered in this study (i.e. municipal solid waste incineration (MSWI) and virgin plastics production). For the three ReCiPe endpoint damage categories, incineration in an MSWI plant results in an impact exceeding that of the examined plastics recycling facility each by about a factor of 4, and the production of virgin plastics has an impact exceeding that of the post-consumer recycled (PCR) plastics production each by a factor of 6–10. On a midpoint indicator level the picture is more differentiated, showing that the environmental impacts of the recycling options are lower by 50% and more for almost all impact factors. While this provides the necessary evidence for the environmental benefits of plastics recycling compared to existing alternatives, it can, however, not be taken as conclusive evidence. To be conclusive, future research will have to address the fate of hazardous substances in the outputs of such recycling systems in more detail. - Highlights: • LCA of plastics production from plastics-rich WEEE treatment residues • Multiple stakeholder perspectives addressed via different research questions • Plastics production from WEEE treatment residues clearly superior to alternatives • Robust results as demonstrated by extensive sensitivity analyses.

  13. Technologies for recycling of plastic wastes; Tecnologias para el reciclado de residuos plasticos

    Energy Technology Data Exchange (ETDEWEB)

    Miguel, R.; Garcia, E.; Larraurim, E.

    1996-12-01

    The present article presents the last technologies to recycle the plastic wastes. the work is developed by Gaiker Center under the umbrella of Brite Euram project. The activities include the minimization, classification, and separation of wastes. (Author)

  14. High Efficiency, High Output Plastic Melt Waste Compactor (HEHO-PMWC) Project

    Data.gov (United States)

    National Aeronautics and Space Administration — ORBITEC proposes to develop processes and waste heat recovery techniques to be incorporated into the existing Plastic Melt Waste Compactor (PMWC) to increase...

  15. Plastic equation of state determined by nano indentation

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    In order to characterize the plastic state of a deformed material, an indentation method to determine the plastic equation of state (PES) was developed. The work-hardening coefficient and the strain rate sensitivity coefficient of the plastic mechanic equation of state were determined by two kinds of indentation tests respectively. Therefore, the PES of materials under deformation can be obtained, and the plastic state of materials can be determined.

  16. Increased Coal Replacement in a Cement Kiln Burner by Feeding a Mixture of Solid Hazardous Waste and Shredded Plastic Waste

    OpenAIRE

    Ariyaratne, W.K.Hiromi; Melaaen, Morten Christian; Tokheim, Lars-André

    2013-01-01

    The present study aims to find the maximum possible replacement of coal by combined feeding of plastic waste and solid hazardous waste mixed with wood chips (SHW) in rotary kiln burners used in cement kiln systems. The coal replacement should be achieved without negative impacts on product quality, emissions or overall operation of the process. A full-scale experiment was carried out in the rotary kiln burner of a cement kiln by varying SHW and plastic waste feeding rates. Experimental ...

  17. Assessment and quantification of plastics waste generation in major 60 cities of India.

    Science.gov (United States)

    Nalini, R; Srinivasulu, B; Shit, Subhas C; Nigam, Suneel Kumar; Akolkar, A B; Dwivedfi, R K

    2013-04-01

    Polymers or plastics materials registered rapid growth in 1970s, 1980s and 1990s at the rate of 2-2.5 times the GDP growth in India. The demand for plastic raw material got more than doubled from 3.3 Million Metric Ton to 6.8 Million Metric Tons in 2010 attributed mainly to rapid urbanization, spread of retail chains, plastics based packaging from grocery to food and vegetable products to cosmetics and consumer items. Plastics packages have its merits over many of conventional materials in the related sector but unless they are collected back effectively after their use to go into recycling process, they become an eyesore in the stream of Municipal Solid Waste (MSW) due to high visibility. As the synthetic and conventional plastics are non-biodegradable in nature, these remain in the dump yards/ landfills for several years, if not collected properly. Due to non- biodegradability, plastics waste remains in the environment for several years, if not collected and disposing plastics wastes at landfills are unsafe since toxic chemicals leach out into the soil and as they contaminate soil and underground water quality. The municipal solid waste also increasing day-by-day due to the inefficient source collection, segregation and transmission of plastics waste for recycling and reusing. In order to find out the realistic plastics waste generation, a study on assessment and quantification of plastics waste has been carried out by CPCB in collaboration with CIPET on selected 60 major cities of India.

  18. Investigation of Performance Analysis and Emission Characteristics of Waste Plastic Fuel

    Science.gov (United States)

    Ruban, M.; Ramasubramanian, S.; Pugazhenthi, R.; Sivaganesan

    2017-03-01

    Today the world is confronted with the twin crisis of fossil fuel depletion and stringent emission norms, because of the environmental awareness. The disposal and degradation of waste plastic is a major issue and scarcities of fuel were major focus area of the researchers. In this virtue the waste plastic fuel extraction makes more attention to the researchers. In this research work focused to find the performance of the waste plastic fuel and compared to diesel. The waste plastic fuel extract from thermal cracking method this process the polymer chains were breakdown into useful lower molecular weight compounds and it becomes plastic pyrolysis it can be utilized as a fuel. The properties of the waste plastic fuel is obtained by various testing process and which is analyze and compare with the fossil fuel diesel. It is found that almost it has similar properties to the diesel and almost all properties of the pyrolysis is closer to that of diesel. The characteristics of the pyrolysis were tested in the engine test bed. The pyrolysis / waste plastic fuel can be directly used in diesel engines over the entire load spectrum smoothly without any major modification. The performance of the waste plastic fuel / pyrolysis is evidenced that it is one of the best alternative fuel as well as the waste plastic can be converted into a useful fuel

  19. Prospects of pyrolysis oil from plastic waste as fuel for diesel engines: A review

    Science.gov (United States)

    Mangesh, V. L.; Padmanabhan, S.; Ganesan, S.; PrabhudevRahul, D.; Reddy, T. Dinesh Kumar

    2017-05-01

    The purpose ofthis study is to review the existing literature about chemical recycling of plastic waste and its potential as fuel for diesel engines. This is a review covering on the field of converting waste plastics into liquid hydrocarbon fuels for diesel engines. Disposal and recycling of waste plastics have become an incremental problem and environmental threat with increasing demand for plastics. One of the effective measures is by converting waste plastic into combustible hydrocarbon liquid as an alternative fuel for running diesel engines. Continued research efforts have been taken by researchers to convert waste plastic in to combustible pyrolysis oil as alternate fuel for diesel engines. An existing literature focuses on the study of chemical structure of the waste plastic pyrolysis compared with diesel oil. Converting waste plastics into fuel oil by different catalysts in catalytic pyrolysis process also reviewed in this paper. The methodology with subsequent hydro treating and hydrocracking of waste plastic pyrolysis oil can reduce unsaturated hydrocarbon bonds which would improve the combustion performance in diesel engines as an alternate fuel.

  20. Preparing Attitude Scale to Define Students‟ Attitudes about Environment, Recycling, Plastic andPlastic Waste

    Directory of Open Access Journals (Sweden)

    Cagri AVAN

    2011-01-01

    Full Text Available The aim of this study is to introduce an attitude scale in order to define students‟ attitudes about environment, recycling, plastics, plastic waste. In this study, 80 attitude sentences according to 5-point Likert-type scale were prepared and applied to 492 students of 6th grade in the Kastamonu city center of Turkey. The scale consists of cognitive, affective, and psychomotor skills domains. After the factor analysis it was found that they have 3, 4 and 5 factors accordingly. After the reliability analysis the alpha values for cognitive, affective and psychomotor scales are .854, .871 and .826 respectively. As a result, it is found that the scale can be used to define cognitive, affective and psychomotor attitudes.

  1. A survey of economic indices of plastic wastes recycling industry

    Directory of Open Access Journals (Sweden)

    Malek Hassanpour

    2015-11-01

    Full Text Available Numerous small recycling units of plastic wastes have been currently constructed heedless to study of economic indices in Iran. Pay attention to the prominent performance of the industrial sector for economic development and its priority for fortifying other sectors to implement job opportunities, survey of the economic indices beckon the stakeholders and industries owners. The main objective of this study was a survey of economic indices in small recycling unit of plastic wastes. Therefore, the practice of computing the economic indices was performed using empirical equations, professional experiences and observations in site of the industry in terms of sustainability performance. Current study had shown the indices values such as value-added percent, profit, annual income, breakeven point, value-added, output value, data value, variable cost of good unit and production costs were found 62%, $ 366558, $ 364292.6, $ 100.34, $ 423451.25, $ 255335.75, $ 678787, $ 389.65 and $ 314494.4 respectively. The breakeven point about 15.93%, the time of return on investment about 1.12 (13.7 months were represented that this industry slightly needs long time to afford the employed capital and starts making a profit.

  2. The Use of Waste Plastic as a Partial Substitution Aggregate in Asphalt Concrete Pavement

    Directory of Open Access Journals (Sweden)

    Imam Aschuri

    2016-04-01

    Full Text Available As a developing country, Indonesia faces serious problems managing solid waste such as plastic. Annually, Indonesia produces approximately 5.4 million tons of waste plastic, accounting for 14% of the country’s total solid waste production. Using waste plastic as a partial substitution aggregate in asphalt concrete pavement would be one of solutions for reducing environmental problems from the high volume of waste plastic. Previous studies show that it may be possible to use waste plastic in road pavement to improve the engineering performance of road pavement and increase its service life. This study investigates the performance of asphalt concrete mixtures containing varying amounts of waste plastic as a partial aggregate substitution as compared to that of conventional mixtures. The waste plastic used in this study was chopped into small pieces of approximately passing sieve number 30 and retained sieve number 40, which would replace (by weight a portion of the mineral aggregates. All mixtures were prepared using 5.82% optimum bitumen content. The performance of asphalt concrete characteristics was studied using the Marshall test, The Indirect Tensile Strength (ITS test, The Indirect Tensile Stiffness Modulus (ITSM test, and the Cantabro Loss (CL test in terms of strength, stiffness modulus, and durability characteristics. In general, laboratory results showed that asphalt concrete mixtures containing waste plastic have higher performance than conventional asphalt concrete mixtures.

  3. Lab-scale thermal analysis of electronic waste plastics

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Wu-Jun; Tian, Ke; Jiang, Hong, E-mail: jhong@ustc.edu.cn; Yu, Han-Qing

    2016-06-05

    Highlights: • We provided the experimental evidence that WEEE can be recovered by pyrolysis method. • We explored the thermochemical behaviors of WEEE using online TG–FTIR–MS technology. • The intramolecular oxygen atoms play a pivotal role in the formation of PBDD/Fs. - Abstract: In this work, we experimentally revealed the thermochemical decomposition pathway of Decabromodiphenyl ethane (DBDPE) and tetrabromobisphenol A (TBBPA) containing electronic waste plastics using an online thermogravimetric–fourier transform infrared–mass spectroscopy (TG–FTIR–MS) system, a high resolution gas chromatography/high resolution mass (HRGC–MS) spectroscopy, and a fixed-bed reactor. We found the distribution and species of produced bromides can be easily controlled by adjusting pyrolytic temperature, which is particularly crucial to their recycle. From the analysis of the liquid and solid phase obtained from the fixed-bed reactor, we proposed that the ·Br radicals formed during the pyrolysis process may be captured by organic species derived from the depolymerization of plastics to form brominated compounds or by the inorganic species in the plastics, and that these species remained in the char residue after pyrolysis. Our work for the first time demonstrates intramolecular oxygen atoms play a pivotal role in the formation of PBDD/Fs that pyrolysis of oxygen-free BFRs is PBDD/Fs-free, whereas pyrolysis of oxygen-containing BFRs is PBDD/Fs-reduced.

  4. Lab-scale thermal analysis of electronic waste plastics.

    Science.gov (United States)

    Liu, Wu-Jun; Tian, Ke; Jiang, Hong; Yu, Han-Qing

    2016-06-05

    In this work, we experimentally revealed the thermochemical decomposition pathway of Decabromodiphenyl ethane (DBDPE) and tetrabromobisphenol A (TBBPA) containing electronic waste plastics using an online thermogravimetric-fourier transform infrared-mass spectroscopy (TG-FTIR-MS) system, a high resolution gas chromatography/high resolution mass (HRGC-MS) spectroscopy, and a fixed-bed reactor. We found the distribution and species of produced bromides can be easily controlled by adjusting pyrolytic temperature, which is particularly crucial to their recycle. From the analysis of the liquid and solid phase obtained from the fixed-bed reactor, we proposed that the Br radicals formed during the pyrolysis process may be captured by organic species derived from the depolymerization of plastics to form brominated compounds or by the inorganic species in the plastics, and that these species remained in the char residue after pyrolysis. Our work for the first time demonstrates intramolecular oxygen atoms play a pivotal role in the formation of PBDD/Fs that pyrolysis of oxygen-free BFRs is PBDD/Fs-free, whereas pyrolysis of oxygen-containing BFRs is PBDD/Fs-reduced.

  5. Measurement of the Specific Heat of Plastic Waste/Fly Ash Composite Material Using Differential Scanning Calorimetry

    Science.gov (United States)

    Fujino, J.; Honda, T.

    2009-06-01

    Plastic waste/fly ash composite, which is made mostly from plastic waste and fly ash, is one of the materials developed for the purpose of recycling. Currently, the composite is used for cable troughs shielding underground lines. However, there exists little information concerning the thermophysical properties of the composite. Thermophysical properties and the structure of the composite must be determined to estimate the heat transfer in the composite and create the different proportions of the composite material. This article deals with measurements of the specific heat of the plastic waste/fly ash composite and its components using a differential scanning calorimeter. The composite sample, which ranged from 10 mg to 19 mg in mass, was cut from a cable trough. The standard reference material is synthetic sapphire disks of 19.6 mg and 29.6 mg in mass. The specific heat of the plastic waste/fly ash composite increases from 1.25 kJ · kg-1 · K-1 to 1.59 kJ · kg-1 · K-1 at temperatures from 305 K to 360 K. The uncertainty for the specific heat data of the composite is estimated to be about 4 %. In addition, the specific heat value depends heavily on the content of the plastic waste.

  6. Flash co-pyrolysis of biomass with plastic waste

    Energy Technology Data Exchange (ETDEWEB)

    T. Cornelissen; S. Schreurs; G. Reggers; R. Carleer; J. Yperman [Hasselt University, Diepenbeek (Belgium). Lab of Applied Chemistry

    2007-07-01

    The Global Warming, the Kyoto Protocol and the emission of greenhouse gasses such as CO{sub 2} are the topics of environmental pleadings. The world's energy supply is limited due to the depletion of fossil fuels, which are still the most important energy sources consumed. The development of new and renewable energies is the key to change. The flash pyrolysis of biomass is a promising route for the production of solid, liquid and gaseous products. A high liquid production requires very low vapour residence time to minimise secondary reactions. Flash co-pyrolytic techniques, at low temperature, provide an alternative way to dispose and convert waste (like plastics) and biomass into high value feedstock. The specific benefits of this method potentially include: the reduction of the volume of the waste, the recovery of chemicals and the replacement of fossil fuels. Co-pyrolysing of PLA (although a biologically degradable polymer, polylactic acid), with biomass (such as willow) may be an alternative waste treatment option. This research indicates that during the flash co-pyrolysis of PLA and willow (even when contaminated with high amounts of heavy metals) a synergy is attained, resulting in a higher yield of bio-oil with a lower water content. 10 refs., 1 fig.

  7. Application Prospect of Waste Plastics%废塑料利用前景

    Institute of Scientific and Technical Information of China (English)

    杨忠敏

    2012-01-01

    详细介绍了废旧塑料的处理和再生利用技术.并指出了废弃塑料再生利用的市场前景。%To introduce the processing and recycling technology of waste plastics. To point out the recycling market prospect of waste plastics.

  8. Managing plastic waste in urban Kenya: niche innovations in production and recycling

    NARCIS (Netherlands)

    Ombis, L.O.

    2012-01-01

    The problems with plastic waste in Kenyan cities are increasing to alarming levels. Especially disposable packaging made of very light plastic materials continues to burden the environment as well as compromise management capacities for waste by city authorities. In light of this, major cities of

  9. Managing plastic waste in urban Kenya: niche innovations in production and recycling

    NARCIS (Netherlands)

    Ombis, L.O.

    2012-01-01

    The problems with plastic waste in Kenyan cities are increasing to alarming levels. Especially disposable packaging made of very light plastic materials continues to burden the environment as well as compromise management capacities for waste by city authorities. In light of this, major cities of Ke

  10. Improving the circular economy via hydrothermal processing of highdensity waste plastics

    DEFF Research Database (Denmark)

    Pedersen, Thomas Helmer; Conti, Federica

    2017-01-01

    Rising environmental concerns on climate changes are causing an increasing attention on circular economies. The plastic economy, in particular, is in focus due to the accelerating consumption of plastics, mainly derived from virgin feedstock, combined with the lack of plastic recycling strategies....... This work presents a novel outlook on the potential of using supercritical hydrothermal processing of waste plastic fractions for tertiary recycling. The study investigates hydrothermal processing of nine different, high-density types of plastics into original resin monomers and other value-added chemical...... processing of high-density plastics is a prospective technology for increasing the circularity of the plastic economy....

  11. The degradability of biodegradable plastics in aerobic and anaerobic waste landfill model reactors.

    Science.gov (United States)

    Ishigaki, Tomonori; Sugano, Wataru; Nakanishi, Akane; Tateda, Masafumi; Ike, Michihiko; Fujita, Masanori

    2004-01-01

    Degradabilities of four kinds of commercial biodegradable plastics (BPs), polyhydroxybutyrate and hydroxyvalerate (PHBV) plastic, polycaprolactone plastic (PCL), blend of starch and polyvinyl alcohol (SPVA) plastic and cellulose acetate (CA) plastic were investigated in waste landfill model reactors that were operated as anaerobically and aerobically. The application of forced aeration to the landfill reactor for supplying aerobic condition could potentially stimulate polymer-degrading microorganisms. However, the individual degradation behavior of BPs under the aerobic condition was completely different. PCL, a chemically synthesized BP, showed film breakage under the both conditions, which may have contributed to a reduction in the waste volume regardless of aerobic or anaerobic conditions. Effective degradation of PHBV plastic was observed in the aerobic condition, though insufficient degradation was observed in the anaerobic condition. But the aeration did not contribute much to accelerate the volume reduction of SPVA plastic and CA plastic. It could be said that the recalcitrant portions of the plastics such as polyvinyl alcohol in SPVA plastic and the highly substituted CA in CA plastic prevented the BP from degradation. These results indicated existence of the great variations in the degradability of BPs in aerobic and anaerobic waste landfills, and suggest that suitable technologies for managing the waste landfill must be combined with utilization of BPs in order to enhance the reduction of waste volume in landfill sites.

  12. The potential for adding plastic waste fuel at a coal gasification power plant.

    Science.gov (United States)

    Campbell, P E; Evans, R H; McMullan, J T; Williams, B C

    2001-12-01

    Plastics wastes from a municipal solid waste plant have a high energy content which make it an interesting option for co-processing with coal. The potential for adding plastic waste to a coal fired Texaco IGCC (Integrated Gasification Combined Cycle) power station is examined. The resulting efficiency increases due to the improved gasification qualities of plastic over coal. For the overall economics to be the same as the coal only case, the maximum amount that the power station can afford to spend on preparing the plastic waste for use is similar to the assumed coal cost, plus the avoided landfill cost, minus the transport cost. The location of the power station plays a key role, since this has an effect on the transport costs as well as on the landfill charges. The sensitivity of the economics of co-processing plastic waste with coal for a variety of power station operational parameters is presented.

  13. Theoretical Framework for Plastic Waste Management in Ghana through Extended Producer Responsibility: Case of Sachet Water Waste

    Directory of Open Access Journals (Sweden)

    Ebo Tawiah Quartey

    2015-08-01

    Full Text Available Currently, use and disposal of plastic by consumers through waste management activities in Ghana not only creates environmental problems, but also reinforces the notion of a wasteful society. The magnitude of this problem has led to increasing pressure from the public for efficient and practical measures to solve the waste problem. This paper analyses the impact of plastic use and disposal in Ghana. It emphasizes the need for commitment to proper management of the impacts of plastic waste and effective environmental management in the country. Sustainable Solid Waste Management (SSWM is a critical problem for developing countries with regards to climate change and greenhouse gas emission, and also the general wellbeing of the populace. Key themes of this paper are producer responsibility and management of products at end of life. The paper proposes two theatrical recovery models that can be used to address the issue of sachet waste in Ghana.

  14. Theoretical Framework for Plastic Waste Management in Ghana through Extended Producer Responsibility: Case of Sachet Water Waste

    Science.gov (United States)

    Quartey, Ebo Tawiah; Tosefa, Hero; Danquah, Kwasi Asare Baffour; Obrsalova, Ilona

    2015-01-01

    Currently, use and disposal of plastic by consumers through waste management activities in Ghana not only creates environmental problems, but also reinforces the notion of a wasteful society. The magnitude of this problem has led to increasing pressure from the public for efficient and practical measures to solve the waste problem. This paper analyses the impact of plastic use and disposal in Ghana. It emphasizes the need for commitment to proper management of the impacts of plastic waste and effective environmental management in the country. Sustainable Solid Waste Management (SSWM) is a critical problem for developing countries with regards to climate change and greenhouse gas emission, and also the general wellbeing of the populace. Key themes of this paper are producer responsibility and management of products at end of life. The paper proposes two theatrical recovery models that can be used to address the issue of sachet waste in Ghana. PMID:26308016

  15. Theoretical Framework for Plastic Waste Management in Ghana through Extended Producer Responsibility: Case of Sachet Water Waste.

    Science.gov (United States)

    Quartey, Ebo Tawiah; Tosefa, Hero; Danquah, Kwasi Asare Baffour; Obrsalova, Ilona

    2015-08-20

    Currently, use and disposal of plastic by consumers through waste management activities in Ghana not only creates environmental problems, but also reinforces the notion of a wasteful society. The magnitude of this problem has led to increasing pressure from the public for efficient and practical measures to solve the waste problem. This paper analyses the impact of plastic use and disposal in Ghana. It emphasizes the need for commitment to proper management of the impacts of plastic waste and effective environmental management in the country. Sustainable Solid Waste Management (SSWM) is a critical problem for developing countries with regards to climate change and greenhouse gas emission, and also the general wellbeing of the populace. Key themes of this paper are producer responsibility and management of products at end of life. The paper proposes two theatrical recovery models that can be used to address the issue of sachet waste in Ghana.

  16. Mortar modified with sulfonated polystyrene produced from waste plastic cups

    Directory of Open Access Journals (Sweden)

    L. A. C. MOTTA

    Full Text Available Abstract In this work, we studied the addition of sulfonated polystyrene produced from waste plastic cups as an admixture for mortars. Mortars were analyzed with polystyrene content of 0.0; 0.2; 0.6; 1.0 and 1.4% in relation to the cement mass. The influence of polystyrene on the mortars' properties was evaluated by the consistency index, water retention, water absorption, porosity, elasticity modulus, compressive strength, flexural strength, bond tensile strength and microscopy. The increase in the sulfonated polystyrene content decreased the elasticity modulus of the mortar and, despite higher porosity, there was a reduction of water absorption by capillarity. In relation to mortar without admixture, the modified mortar showed an increase in water retention and consistency index, and a large increase in flexural strength and bond tensile strength. The significant increase of bond tensile strength (214% with admixture 1% highlights the potential of the produced material as an adhesive mortar.

  17. Contribution of plastic waste recovery to greenhouse gas (GHG) savings in Spain.

    Science.gov (United States)

    Sevigné-Itoiz, Eva; Gasol, Carles M; Rieradevall, Joan; Gabarrell, Xavier

    2015-12-01

    This paper concentrates on the quantification of greenhouse gas (GHG) emissions of post-consumer plastic waste recovery (material or energy) by considering the influence of the plastic waste quality (high or low), the recycled plastic applications (virgin plastic substitution or non-plastic substitution) and the markets of recovered plastic (regional or global). The aim is to quantify the environmental consequences of different alternatives in order to evaluate opportunities and limitations to select the best and most feasible plastic waste recovery option to decrease the GHG emissions. The methodologies of material flow analysis (MFA) for a time period of thirteen years and consequential life cycle assessment (CLCA) have been integrated. The study focuses on Spain as a representative country for Europe. The results show that to improve resource efficiency and avoid more GHG emissions, the options for plastic waste management are dependent on the quality of the recovered plastic. The results also show that there is an increasing trend of exporting plastic waste for recycling, mainly to China, that reduces the GHG benefits from recycling, suggesting that a new focus should be introduced to take into account the split between local recycling and exporting.

  18. Mechanical and chemical recycling of solid plastic waste.

    Science.gov (United States)

    Ragaert, Kim; Delva, Laurens; Van Geem, Kevin

    2017-08-17

    This review presents a comprehensive description of the current pathways for recycling of polymers, via both mechanical and chemical recycling. The principles of these recycling pathways are framed against current-day industrial reality, by discussing predominant industrial technologies, design strategies and recycling examples of specific waste streams. Starting with an overview on types of solid plastic waste (SPW) and their origins, the manuscript continues with a discussion on the different valorisation options for SPW. The section on mechanical recycling contains an overview of current sorting technologies, specific challenges for mechanical recycling such as thermo-mechanical or lifetime degradation and the immiscibility of polymer blends. It also includes some industrial examples such as polyethylene terephthalate (PET) recycling, and SPW from post-consumer packaging, end-of-life vehicles or electr(on)ic devices. A separate section is dedicated to the relationship between design and recycling, emphasizing the role of concepts such as Design from Recycling. The section on chemical recycling collects a state-of-the-art on techniques such as chemolysis, pyrolysis, fluid catalytic cracking, hydrogen techniques and gasification. Additionally, this review discusses the main challenges (and some potential remedies) to these recycling strategies and ground them in the relevant polymer science, thus providing an academic angle as well as an applied one. Copyright © 2017 Elsevier Ltd. All rights reserved.

  19. Determinants of consumer food waste behaviour

    DEFF Research Database (Denmark)

    Stancu, Violeta; Haugaard, Pernille; Lähteenmäki, Liisa

    2016-01-01

    . Yet, there is still little evidence regarding the determinants of consumers' food waste behaviour. The present study examines the effect of psycho-social factors, food-related routines, household perceived capabilities and socio-demographic characteristics on self-reported food waste. Survey data......Approximately one quarter of the food supplied for human consumption is wasted across the food supply chain. In the high income countries, the food waste generated at the household level represents about half of the total food waste, making this level one of the biggest contributors to food waste...... gathered among 1062 Danish respondents measured consumers' intentions not to waste food, planning, shopping and reuse of leftovers routines, perceived capability to deal with household food-related activities, injunctive and moral norms, attitudes towards food waste, and perceived behavioural control...

  20. Life cycle assessment of post-consumer plastics production from waste electrical and electronic equipment (WEEE) treatment residues in a Central European plastics recycling plant.

    Science.gov (United States)

    Wäger, Patrick A; Hischier, Roland

    2015-10-01

    Plastics play an increasingly important role in reaching the recovery and recycling rates defined in the European WEEE Directive. In a recent study we have determined the life cycle environmental impacts of post-consumer plastics production from mixed, plastics-rich WEEE treatment residues in the Central European plant of a market-leading plastics recycler, both from the perspective of the customers delivering the residues and the customers buying the obtained post-consumer recycled plastics. The results of our life cycle assessments, which were extensively tested with sensitivity analyses, show that from both perspectives plastics recycling is clearly superior to the alternatives considered in this study (i.e. municipal solid waste incineration (MSWI) and virgin plastics production). For the three ReCiPe endpoint damage categories, incineration in an MSWI plant results in an impact exceeding that of the examined plastics recycling facility each by about a factor of 4, and the production of virgin plastics has an impact exceeding that of the post-consumer recycled (PCR) plastics production each by a factor of 6-10. On a midpoint indicator level the picture is more differentiated, showing that the environmental impacts of the recycling options are lower by 50% and more for almost all impact factors. While this provides the necessary evidence for the environmental benefits of plastics recycling compared to existing alternatives, it can, however, not be taken as conclusive evidence. To be conclusive, future research will have to address the fate of hazardous substances in the outputs of such recycling systems in more detail.

  1. Plastic Solid Waste Assessment in the State of Kuwait and Proposed Methods of Recycling

    Directory of Open Access Journals (Sweden)

    S. Al-Salem

    2007-01-01

    Full Text Available A proper assessment of Solid Plastic Waste (SPW in Kuwait will provide a greater understanding to the industry of plastic manufacturing and manufacturers as well as direct the strategic future plans proposed into execution. This research show the results obtained after a years survey and study of plastic solid waste in the state of Kuwait and the surrounding region in order to create a database that can be used in future plans and research projects. Major manufacturers in the area were asked to complete a questionnaire to create a complete database. Recycling methods were studied and tested in order to evaluate the best solutions and schemes available to overcome the increasing rate of municipal plastic waste. From the current study it, Kuwait ranked in second behind Qatar in plastic waste but land filling rates in Kuwait are almost double than any other oil dependant country in the west Asia region.

  2. Vehicle routing for the eco-efficient collection of household plastic waste.

    Science.gov (United States)

    Bing, Xiaoyun; de Keizer, Marlies; Bloemhof-Ruwaard, Jacqueline M; van der Vorst, Jack G A J

    2014-04-01

    Plastic waste is a special category of municipal solid waste. Plastic waste collection is featured with various alternatives of collection methods (curbside/drop-off) and separation methods (source-/post-separation). In the Netherlands, the collection routes of plastic waste are the same as those of other waste, although plastic is different than other waste in terms of volume to weight ratio. This paper aims for redesigning the collection routes and compares the collection options of plastic waste using eco-efficiency as performance indicator. Eco-efficiency concerns the trade-off between environmental impacts, social issues and costs. The collection problem is modeled as a vehicle routing problem. A tabu search heuristic is used to improve the routes. Collection alternatives are compared by a scenario study approach. Real distances between locations are calculated with MapPoint. The scenario study is conducted based on real case data of the Dutch municipality Wageningen. Scenarios are designed according to the collection alternatives with different assumptions in collection method, vehicle type, collection frequency and collection points, etc. Results show that the current collection routes can be improved in terms of eco-efficiency performance by using our method. The source-separation drop-off collection scenario has the best performance for plastic collection assuming householders take the waste to the drop-off points in a sustainable manner. The model also shows to be an efficient decision support tool to investigate the impacts of future changes such as alternative vehicle type and different response rates.

  3. Damage-plasticity model of the host rock in a nuclear waste repository

    Science.gov (United States)

    Koudelka, Tomáš; Kruis, Jaroslav

    2016-06-01

    The paper describes damage-plasticity model for the modelling of the host rock environment of a nuclear waste repository. Radioactive Waste Repository Authority in Czech Republic assumes the repository to be in a granite rock mass which exhibit anisotropic behaviour where the strength in tension is lower than in compression. In order to describe this phenomenon, the damage-plasticity model is formulated with the help of the Drucker-Prager yield criterion which can be set to capture the compression behaviour while the tensile stress states is described with the help of scalar isotropic damage model. The concept of damage-plasticity model was implemented in the SIFEL finite element code and consequently, the code was used for the simulation of the Äspö Pillar Stability Experiment (APSE) which was performed in order to determine yielding strength under various conditions in similar granite rocks as in Czech Republic. The results from the performed analysis are presented and discussed in the paper.

  4. Recycling plastics and polymeric wastes. (Latest citations from the EI compendex*plus database). Published Search

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-11-01

    The bibliography contains citations concerning the recycling and uses of plastic and polymeric scraps and wastes. Topics include communition or grinding of scrap, degradation by heat or chemical reaction, compatibility of various plastics with one another, sorting problems, physical properties of reprocessed materials, economics, public awareness, waste minimization, waste re-use, and foreign experience in plastics recycling. New products made from recycled materials, and products expressly made to be recyclable are also discussed. (Contains 50-250 citations and includes a subject term index and title list.) (Copyright NERAC, Inc. 1995)

  5. Municipal solid waste composition determination supporting the integrated solid waste management system in the island of Crete.

    Science.gov (United States)

    Gidarakos, E; Havas, G; Ntzamilis, P

    2006-01-01

    A one-year survey was conducted in the greater region of Crete (located at the lower region of the Aegean Sea) for the purpose of identifying waste composition (including chemical and physical characterization), as well as any seasonal variation. The investigation was carried out repeatedly at seven landfills and one transfer station in Crete, in four phases. Each sampling phase corresponded to a season (autumn, winter, spring, summer). ASTM D5231-92(2003) standard method and RCRA Waste Sampling Draft Technical Guidance were used. Hand sorting was used for classifying the collected wastes into the following categories: plastics, paper, metals, aluminium, leather-wood-textiles-rubbers, organic wastes, non-combustibles and miscellaneous. Further analysis included proximate and ultimate analysis of combustible materials. Metals such as lead, cadmium and mercury were also investigated. The results show that there has been a significant decrease of organic wastes during the last decade due to the increase of packaging materials, as a result of a change in consumption patterns. Three main waste categories were determined: organic wastes, paper and plastics, which combined represent 76% of the total waste in Crete. Furthermore, a high fraction of glass and a seasonal variation of aluminium indicate a strong correlation of waste composition with certain human activities, such as tourism. There is also a variation between the municipal solid waste (MSW) composition in the region of Crete (2003-2004) and MSW composition suggested in the National Solid Waste Planning (2000) [National Solid Waste Planning, 2000. Completion and particularization of Common Ministerial Act 113944//1944/1997: National Solid Waste Planning, June 2000]. The results of this survey are to be utilized by the regional solid waste authorities in order to establish an integrated waste treatment site, capable of fulfilling the regional waste management demands.

  6. WATER RESISTANCE OF WOOD - PLASTIC COMPOSITES MADE FROM WASTE MATERIALS RESULTED IN THE FURNITURE MANUFACTURING PROCESS

    Directory of Open Access Journals (Sweden)

    Camelia COŞEREANU

    2014-12-01

    Full Text Available The purpose of this paper is to present innovative wood-plastic composites made from waste materials such as ABS (acrylonitrile butadiene styrene and wood shavings resulted in the furniture manufacturing process. From previous investigations (with regard to physical integrity and compactness of the panels, only mixtures ranging from a ratio of 100% ABS: 0% shavings to 80% ABS: 20% shavings were selected for water resistance testing. Swelling in thickness and water absorption for 2h and 24h were determined for the proposed wood-plastic composites. The results have shown that only a participation of up to 10% of wood shavings in the tested panels conducted to a good performance

  7. Scenarios study on post-consumer plastic packaging waste recycling

    NARCIS (Netherlands)

    Thoden van Velzen, E.U.; Bos-Brouwers, H.E.J.; Groot, J.J.; Bing Xiaoyun, Xiaoyun; Jansen, M.; Luijsterburg, B.

    2013-01-01

    We all use plastics on a daily basis. Plastics come in many shapes, sizes and compositions and are used in a wide variety of products. Almost all of the currently used plastic packaging are made from fossil resources, which are finite. The production of plastic packages causes environmental impacts,

  8. Scenarios study on post-consumer plastic packaging waste recycling

    NARCIS (Netherlands)

    Thoden van Velzen, E.U.; Bos-Brouwers, H.E.J.; Groot, J.J.; Bing Xiaoyun, Xiaoyun; Jansen, M.; Luijsterburg, B.

    2013-01-01

    We all use plastics on a daily basis. Plastics come in many shapes, sizes and compositions and are used in a wide variety of products. Almost all of the currently used plastic packaging are made from fossil resources, which are finite. The production of plastic packages causes environmental impacts,

  9. An econometric analysis of regional differences in household waste collection: the case of plastic packaging waste in Sweden.

    Science.gov (United States)

    Hage, Olle; Söderholm, Patrik

    2008-01-01

    The Swedish producer responsibility ordinance mandates producers to collect and recycle packaging materials. This paper investigates the main determinants of collection rates of household plastic packaging waste in Swedish municipalities. This is done by the use of a regression analysis based on cross-sectional data for 252 Swedish municipalities. The results suggest that local policies, geographic/demographic variables, socio-economic factors and environmental preferences all help explain inter-municipality collection rates. For instance, the collection rate appears to be positively affected by increases in the unemployment rate, the share of private houses, and the presence of immigrants (unless newly arrived) in the municipality. The impacts of distance to recycling industry, urbanization rate and population density on collection outcomes turn out, though, to be both statistically and economically insignificant. A reasonable explanation for this is that the monetary compensation from the material companies to the collection entrepreneurs vary depending on region and is typically higher in high-cost regions. This implies that the plastic packaging collection in Sweden may be cost ineffective. Finally, the analysis also shows that municipalities that employ weight-based waste management fees generally experience higher collection rates than those municipalities in which flat and/or volume-based fees are used.

  10. The knowledge, awareness, attitude and motivational analysis of plastic waste and household perspective in Malaysia.

    Science.gov (United States)

    Afroz, Rafia; Rahman, Ataur; Masud, Muhammad Mehedi; Akhtar, Rulia

    2017-01-01

    The focus of this study is to analyze the level of knowledge, awareness, and attitude toward plastic waste and to distinguish the key drivers that encourage the households in Kuala Lumpur, Malaysia, to participate in "No plastic campaign," This study used the logistic regression model to explain the factors that may affect the willingness to participate (WTP) of households in the campaign. In this study, it is found that 35 % of households are willing to participate in the campaign. The results of the study also indicate that people who are more informed and more convinced of their knowledge have a more positive attitude toward recycling than their counterparts do. Furthermore, this study provides additional evidence of the level and classification of importance of motivating factors for plastic recycling, using the modified average and coefficient of variation of the models. From the analysis, the factor "helps reduce landfill use" is found as the most important factor and the factor of "raising money for charity" is found as the least important factor that motivates households to participate in recycling. The determinations of the study suggest some strategies that could hold implications for government and households to boost them to participate in the campaign "No Plastic Bag."

  11. Laboratory test methods to determine the degradation of plastics in marine environmental conditions.

    Science.gov (United States)

    Tosin, Maurizio; Weber, Miriam; Siotto, Michela; Lott, Christian; Degli Innocenti, Francesco

    2012-01-01

    In this technology report, three test methods were developed to characterize the degradation of plastic in marine environment. The aim was to outline a test methodology to measure the physical and biological degradation in different habitats where plastic waste can deposit when littered in the sea. Previously, research has focused mainly on the conditions encountered by plastic items when floating in the sea water (pelagic domain). However, this is just one of the possible habitats that plastic waste can be exposed to. Waves and tides tend to wash up plastic waste on the shoreline, which is also a relevant habitat to be studied. Therefore, the degradation of plastic items buried under sand kept wet with sea water has been followed by verifying the disintegration (visual disappearing) as a simulation of the tidal zone. Most biodegradable plastics have higher densities than water and also as a consequence of fouling, they tend to sink and lay on the sea floor. Therefore, the fate of plastic items lying on the sediment has been followed by monitoring the oxygen consumption (biodegradation). Also the effect of a prolonged exposure to the sea water, to simulate the pelagic domain, has been tested by measuring the decay of mechanical properties. The test material (Mater-Bi) was shown to degrade (total disintegration achieved in less than 9 months) when buried in wet sand (simulation test of the tidal zone), to lose mechanical properties but still maintain integrity (tensile strength at break = -66% in 2 years) when exposed to sea water in an aquarium (simulation of pelagic domain), and substantially biodegrade (69% in 236 days; biodegradation relative to paper: 88%) when located at the sediment/sea water interface (simulation of benthic domain). This study is not conclusive as the methodological approach must be completed by also determining degradation occurring in the supralittoral zone, on the deep sea floor, and in the anoxic sediment.

  12. Laboratory Test Methods to Determine the Degradation of Plastics in Marine Environmental Conditions

    Science.gov (United States)

    Tosin, Maurizio; Weber, Miriam; Siotto, Michela; Lott, Christian; Degli Innocenti, Francesco

    2012-01-01

    In this technology report, three test methods were developed to characterize the degradation of plastic in marine environment. The aim was to outline a test methodology to measure the physical and biological degradation in different habitats where plastic waste can deposit when littered in the sea. Previously, research has focused mainly on the conditions encountered by plastic items when floating in the sea water (pelagic domain). However, this is just one of the possible habitats that plastic waste can be exposed to. Waves and tides tend to wash up plastic waste on the shoreline, which is also a relevant habitat to be studied. Therefore, the degradation of plastic items buried under sand kept wet with sea water has been followed by verifying the disintegration (visual disappearing) as a simulation of the tidal zone. Most biodegradable plastics have higher densities than water and also as a consequence of fouling, they tend to sink and lay on the sea floor. Therefore, the fate of plastic items lying on the sediment has been followed by monitoring the oxygen consumption (biodegradation). Also the effect of a prolonged exposure to the sea water, to simulate the pelagic domain, has been tested by measuring the decay of mechanical properties. The test material (Mater-Bi) was shown to degrade (total disintegration achieved in less than 9 months) when buried in wet sand (simulation test of the tidal zone), to lose mechanical properties but still maintain integrity (tensile strength at break = −66% in 2 years) when exposed to sea water in an aquarium (simulation of pelagic domain), and substantially biodegrade (69% in 236 days; biodegradation relative to paper: 88%) when located at the sediment/sea water interface (simulation of benthic domain). This study is not conclusive as the methodological approach must be completed by also determining degradation occurring in the supralittoral zone, on the deep sea floor, and in the anoxic sediment. PMID:22737147

  13. Laboratory test methods to determine the degradation of plastics in marine environmental conditions

    Directory of Open Access Journals (Sweden)

    Maurizio eTosin

    2012-06-01

    Full Text Available In this technology report, three test methods were developed to characterize the degradation of plastic in marine environment. The aim was to outline a test methodology to measure the physical and biological degradation in different habitats where plastic waste can deposit when littered in the sea. Previously, research has focused mainly on the conditions encountered by plastic items when floating in the sea water (pelagic domain. However, this is just one of the possible habitats that plastic waste can be exposed to. Waves and tides tend to wash up plastic waste on the shoreline, which is also a relevant habitat to be studied. Therefore, the degradation of plastic items buried under sand kept wet with sea water has been followed by verifying the disintegration (visual disappearing as a simulation of the tidal zone. Most biodegradable plastics have higher densities than water and also as a consequence of fouling, they tend to sink and lay on the sea floor. Therefore, the fate of plastic items lying on the sediment has been followed by monitoring the oxygen consumption (biodegradation. Also the effect of a prolonged exposure to the sea water, to simulate the pelagic domain, has been tested by measuring the decay of mechanical properties. The test material (Mater-Bi was shown to degrade (total disintegration achieved in less than 9 months when buried in wet sand (simulation test of the tidal zone, to lose mechanical properties but still maintain integrity (tensile strength at break = -66% in 2 years when exposed to sea water in an aquarium (simulation of pelagic domain, and substantially biodegrade (69% in 236 days; biodegradation relative to paper: 88% when located at the sediment/sea water interface (simulation of benthic domain. This study is not conclusive as the methodological approach must be completed by also determining degradation occurring in the supralittoral zone, on the deep sea floor, and in the anoxic sediment.

  14. Waste characterisation, determining the energy potential of waste

    CSIR Research Space (South Africa)

    Oelofse, Suzanna HH

    2015-11-01

    Full Text Available stream_source_info Oelofse2_2015.pdf.txt stream_content_type text/plain stream_size 4108 Content-Encoding UTF-8 stream_name Oelofse2_2015.pdf.txt Content-Type text/plain; charset=UTF-8 1 Waste characterisation..., determining the energy potential of waste 25 November 2015 by Prof Suzan Oelofse Research Group Leader: Waste for Development Competency Area: Solutions for a Green Economy 2 WtE should consider Fitness for purpose • Feedstock...

  15. Review Paper on Application of Waste Plastic in Modifying Bitumen Properties

    Directory of Open Access Journals (Sweden)

    AdityaBhardwaj

    2017-04-01

    Full Text Available Industrialisation and population is increasing day by day leading to the increase in the amount of waste plastic. Plastic is a non-biodegradable substance i.e. it is not decomposed by bacteria easily. So, dumping it causes soil pollution which leads to decrease in the fertility of soil. Another way of getting rid of plastic is by burning it, which also produces a lot of harmful gases and leads to increase in air pollution. Soil and air pollution both are harmful for the environment. Waste plastic can be used in bitumen as a modifier. In this paper we will discuss the variation of the properties of bitumen on addition of waste plastic at different percentage.

  16. High Efficiency, High Output Plastic Melt Waste Compactor (HEHO-PMWC) Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The innovative High Efficiency, High Output Plastic Melt Waste Compactor (HEHO-PMWC) is a trash dewatering and volume reduction system that uses heat melt compaction...

  17. Valorisation of waste plastic bags in cement-mortar composites as ...

    African Journals Online (AJOL)

    2015-01-07

    Jan 7, 2015 ... problems in Benin due both to the non-biodegradability of such by-products .... waste plastic bags inclusion process into the construction of buildings, .... (mass MD)and heated to fuse in an appropriate metallic container.

  18. Disposal of Waste Plastics With Traditional Coking Process

    Institute of Scientific and Technical Information of China (English)

    CAI Jiu-ju; YU Guang-wei; LIAO Hong-qiang; QIAN Kai; ZHAO Pen; HE Ya-bin

    2006-01-01

    A new technology for treating waste plastics (WP) by traditional coking process was introduced. With a thermo-balance and a 10 g atmospheric fixed bed reactor, the thermo-gravimetric behavior and product were studied during co-coking of WP with blended coal. And then, using a coke-oven with capacity of 200 kg, the characteristics of products were assessed. The results showed that there is an overlapping temperature range (200-550 ℃) of decomposition between WP and blended coal, and the pyrolysis synergism index η and synergism strength β proposed could evaluate the synergism between them. 1% of added WP results in the maximum synergism in all series experiments. The increase of added WP decreases the synergism. Tar yield in co-coking is increased with the decrease of water yield for synergism. Moreover, it was also found that the quality indexes of coke, such as M10, M40, CRI and CSR, are degraded with the increase of WP until 4%, though the quality of tar and gas is optimized for WP addition.

  19. Assessing the effect of biodegradable and degradable plastics on the composting of green wastes and compost quality.

    Science.gov (United States)

    Unmar, G; Mohee, R

    2008-10-01

    An assessment of the effect of the composting potential of Mater-Bi biodegradable plastic with green wastes, noted by GBIO, and degradable plastic (PDQ-H additive) with green wastes, noted by GDEG, was carried out in a lagged two-compartment compost reactor. The composting time was determined until constant mass of the composting substrates was reached. The green wastes composting process was used as control (G). After one week of composting, the biodegradable plastics disappeared completely, while 2% of the original degradable plastic still remained after about 8 weeks of composting. A net reduction in volatile solids contents of 61.8%, 56.5% and 53.2% were obtained for G, GBIO and GDEG, respectively. Compost quality was assessed in terms of nitrogen, potassium and phosphorus contents, which were found to be highest for GBIO compost. From the phytotoxicity test, it has been observed that a diluted extract of GBIO compost has produced the longest length of radicle. From the respiration test, no significant difference in the amount of carbon dioxide released by the composting of GDEG and G was observed. This study showed that the quality of the compost is not affected by the presence of the biodegradable and degradable plastics in the raw materials.

  20. Development of a Plastic Melt Waste Compactor for Space Missions Experiments and Prototype Design

    Science.gov (United States)

    Pace, Gregory; Wignarajah, Kanapathipillai; Pisharody, Suresh; Fisher, John

    2004-01-01

    This paper describes development at NASA Ames Research Center of a heat melt compactor that can be used on both near term and far term missions. Experiments have been performed to characterize the behavior of composite wastes that are representative of the types of wastes produced on current and previous space missions such as International Space Station, Space Shuttle, MIR and Skylab. Experiments were conducted to characterize the volume reduction, bonding, encapsulation and biological stability of the waste composite and also to investigate other key design issues such as plastic extrusion, noxious off-gassing and removal of the of the plastic waste product from the processor. The experiments provided the data needed to design a prototype plastic melt waste processor, a description of which is included in the paper.

  1. Integrated Index in Consideration of Appropriate Plastic Recycling System in Waste Bank Operation

    Directory of Open Access Journals (Sweden)

    Firdaus Pambudi Noorhan

    2016-01-01

    Full Text Available Several appropriate technology had been developed to maintain plastic waste in society according to minimize environmental impact. Landfill is no longer appropriate to maintain plastic waste based on the environmental impact that might be occurred for instance. However in developing countries such as Indonesia, although plastic recycling technology have been promoted by maintain waste bank policy for support community willingness to exchange their recyclable waste with certain monetary values, there is no guarantee that community will fully accept plastic recycling technology. This research aims to assess the performance of plastic recycling in environmental and social aspects as its integrated index. From that assessment, appropriate strategies in plastic recycling will be delivered in this research. Environmental aspects will be assessed by using life cycle assessment (LCA through MiLCA software and selected by using data envelopment analysis (DEA. Social aspects will be analyzed by using qualitative and quantitative methodology such as observation, interview, secondary data, and questionnaires. Simulation and modelling will also developed by using agent-based modelling (ABM to describe social dynamic of community in supporting waste bank policy. The appropriate system of plastic recycling will be promoted as expected results for this research.

  2. WOOD - PLASTIC COMPOSITES FROM WASTE MATERIALS RESULTED IN THE FURNITURE MANUFACTURING PROCESS

    Directory of Open Access Journals (Sweden)

    Camelia COŞEREANU

    2014-06-01

    Full Text Available The paper presents the application of waste materials resulted in the furniture manufacturing process as components for wood-plastic composites. The composites are produced from industrial byproducts, such as shavings and ABS (acrylonitrile butadiene styrene, without coupling agent. The two components are derived from industrial processes of furniture manufacturing: the first one consists of wood residues resulted from planing machine as planer shavings, and the second one from ABS edge banding operation. A wide array of mixtures varying from 100% ABS to 50% ABS: 50% shavings were used to produce eight variants of boards. Density was determined for each board and the method for the determination of ABS particle size distribution by oscillating screen method using sieve apertures up to 4mm was also applied, in order to establish the particle fractions and the distribution of their sizes. Based on ABS properties, several technologies of manufacturing wood-plastic composites from the waste materials were tested and one of them was selected. The results of the first stage analysis, when the physical integrity and the compactness of the panels’ structures were tested, have shown that a maximum proportion of 30% of wood shavings is accepted in the mixture. On the other hand, the low density of the boards and their porous structure recommend further investigations for thermal and sound insulation applications

  3. Recycling and recovery of post-consumer plastic solid waste in a European context

    Directory of Open Access Journals (Sweden)

    Dewil Raf

    2012-01-01

    Full Text Available The disposal of waste plastics has become a major worldwide environmental problem. The USA, Europe and Japan generate annually about 50 million tons of post-consumer plastic waste, previously landfilled, generally considered as a non-sustainable and environmentally questionable option. Landfill sites and their capacity are, moreover, decreasing rapidly, and legislation is stringent. Several European Directives and US legislation concern plastic wastes and the required management. They are briefly discussed in this paper. New processes have emerged, i.e., advanced mechanical recycling of plastic waste as virgin or second grade plastic feedstock, and thermal treatments to recycle the waste as virgin monomer, as synthetic fuel gas, or as heat source (incineration with energy recovery. These processes avoid land filling, where the non-biodegradable plastics remain a lasting environmental burden. The paper reviews these alternative options through mostly thermal processing (pyrolysis, gasification and waste-to-energy. Additional research is, however, still needed to confirm the potential on pilot and commercial scale. [Acknowledgments. The research was partly funded by the Fundamental Research Funds for the Central Universities RC1101 (PR China and partly funded by Project KP/09/005 (SCORES4CHEM Knowledge Platform of the Industrial Research Council of the KU Leuven (Belgium.

  4. Fluidized-Bed Gasification of Plastic Waste, Wood, and Their Blends with Coal

    Directory of Open Access Journals (Sweden)

    Lucio Zaccariello

    2015-08-01

    Full Text Available The effect of fuel composition on gasification process performance was investigated by performing mass and energy balances on a pre-pilot scale bubbling fluidized bed reactor fed with mixtures of plastic waste, wood, and coal. The fuels containing plastic waste produced less H2, CO, and CO2 and more light hydrocarbons than the fuels including biomass. The lower heating value (LHV progressively increased from 5.1 to 7.9 MJ/Nm3 when the plastic waste fraction was moved from 0% to 100%. Higher carbonaceous fines production was associated with the fuel containing a large fraction of coal (60%, producing 87.5 g/kgFuel compared to only 1.0 g/kgFuel obtained during the gasification test with just plastic waste. Conversely, plastic waste gasification produced the highest tar yield, 161.9 g/kgFuel, while woody biomass generated only 13.4 g/kgFuel. Wood gasification showed a carbon conversion efficiency (CCE of 0.93, while the tests with two fuels containing coal showed lowest CCE values (0.78 and 0.70, respectively. Plastic waste and wood gasification presented similar cold gas efficiency (CGE values (0.75 and 0.76, respectively, while that obtained during the co-gasification tests varied from 0.53 to 0.73.

  5. Post Separation of Plastic Waste: Better for the Environment and Lower Collection Costs

    NARCIS (Netherlands)

    E. Dijkgraaf (Elbert); R.H.J.M. Gradus (Raymond)

    2016-01-01

    textabstractThe European Union (EU) advocates a plastic waste recycling rate of more than 55% through home separation by households. Even for the Netherlands, which has already invested heavily in plastic recycling policies, there is still a challenge to meet this target. We show that post

  6. Post Separation of Plastic Waste: Better for the Environment and Lower Collection Costs

    NARCIS (Netherlands)

    E. Dijkgraaf (Elbert); R.H.J.M. Gradus (Raymond)

    2016-01-01

    textabstractThe European Union (EU) advocates a plastic waste recycling rate of more than 55% through home separation by households. Even for the Netherlands, which has already invested heavily in plastic recycling policies, there is still a challenge to meet this target. We show that post separatio

  7. Research and Development of a New Waste Collection Bin to Facilitate Education in Plastic Recycling

    Science.gov (United States)

    Chow, Cheuk-fai; So, Wing-Mui Winnie; Cheung, Tsz-Yan

    2016-01-01

    Plastic recycling has been an alternative method for solid waste management apart from landfill and incineration. However, recycling quality is affected when all plastics are discarded into a single recycling bin that increases cross contaminations and operation cost to the recycling industry. Following the engineering design process, a new…

  8. Research and Development of a New Waste Collection Bin to Facilitate Education in Plastic Recycling

    Science.gov (United States)

    Chow, Cheuk-fai; So, Wing-Mui Winnie; Cheung, Tsz-Yan

    2016-01-01

    Plastic recycling has been an alternative method for solid waste management apart from landfill and incineration. However, recycling quality is affected when all plastics are discarded into a single recycling bin that increases cross contaminations and operation cost to the recycling industry. Following the engineering design process, a new…

  9. Catalytic thermal cracking of post-consumer waste plastics to fuels: Part 1 - Kinetics and optimization

    Science.gov (United States)

    Thermogravimetric analysis (TGA) was used to investigate thermal and catalytic pyrolysis of waste plastics such as prescription bottles (polypropylene/PP), high density polyethylene, landfill liners (polyethylene/PE), packing materials (polystyrene/PS), and foams (polyurethane/PU) into crude plastic...

  10. Characterisation of plastic packaging waste for recycling: problems related to current approaches

    DEFF Research Database (Denmark)

    Götze, Ramona; Astrup, Thomas Fruergaard

    2013-01-01

    criteria of recycling processes. A lack of information in current waste characterisation practise on polymer resin composition, black coloured material content and the influence of surface adherent material on physico-chemical characteristics of plastic packaging waste were identified. These shortcomings...

  11. A Research Needs Assessment for waste plastics recycling: Volume 1, Executive summary. Final report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-12-01

    This first volume provides a summary of the entire project. The study utilized the talents of a large number of participants, including a significant number of peer reviewers from industrial companies, government agencies, and research institutes. in addition, an extensive analysis of relevant literature was carried out. In considering the attractiveness of recycling technologies that are alternatives to waste-to-energy combustion units, a systems approach was utilized. Collection of waste streams containing plastics, sortation, and reclamation of plastics and plastic mixtures, reprocessing or chemical conversion of the reclaimed polymers, and the applicability of the products to specific market segments have been analyzed in the study.

  12. Production of steam cracking feedstocks by mild cracking of plastic wastes

    Energy Technology Data Exchange (ETDEWEB)

    Angyal, Andras; Miskolczi, Norbert; Bartha, Laszlo; Tungler, Antal; Nagy, Lajos; Vida, Laszlo; Nagy, Gabor

    2010-11-15

    In this work the utility of new possible petrochemical feedstocks obtained by plastic waste cracking has been studied. The cracking process of polyethylene (PE), polyethylene-polypropylene (PEPP) and polyethylene-polystyrene (PEPS) has been carried out in a pilot scale tubular reactor. In this process mild reaction parameters has been applied, with the temperature of 530 C and the residence time of 15 min. The produced hydrocarbon fractions as light- and middle distillates were tested by using a laboratory steam cracking unit. It was concluded that the products of the mild cracking of plastic wastes could be applied as petrochemical feedstocks. Based on the analytical data it was determined that these liquid products contained in significant concentration (25-50 wt.%) of olefin hydrocarbons. Moreover the cracking of polystyrene containing raw material resulted in liquid products with significant amounts of aromatic hydrocarbons too. The steam cracking experiments proved that the products obtained by PE and PEPP cracking resulted in similar or better ethylene and propylene yields than the reference samples, however the aromatic content of PEPS products reduced the ethylene and propylene yields. (author)

  13. Waste plastics as supplemental fuel in the blast furnace process: improving combustion efficiencies.

    Science.gov (United States)

    Kim, Dongsu; Shin, Sunghye; Sohn, Seungman; Choi, Jinshik; Ban, Bongchan

    2002-10-14

    The possibility of using waste plastics as a source of secondary fuel in a blast furnace has been of recent interest. The success of this process, however, will be critically dependent upon the optimization of operating systems. For instance, the supply of waste plastics must be reliable as well as economically attractive compared with conventional secondary fuels such as heavy oil, natural gas and pulverized coal. In this work, we put special importance on the improvement of the combustibility of waste plastics as a way to enhance energy efficiency in a blast furnace. As experimental variables to approach this target, the effects of plastic particle size, blast temperature, and the level of oxygen enrichment were investigated using a custom-made blast model designed to simulate a real furnace. Lastly, the combustion efficiency of the mixture of waste plastics and pulverized coal was tested. The observations made from these experiments led us to the conclusion that with the increase of both blast temperature and the level of oxygen enrichment, and with a decrease in particle size, the combustibility of waste polyethylene could be improved at a given distance from the tuyere. Also it was found that the efficiency of coal combustion decreased with the addition of plastics; however, the combustion efficiency of mixture could be comparable at a longer distance from the tuyere.

  14. Effects of Waste Plastic on the Physical and Rheological Properties of Bitumen

    Science.gov (United States)

    Ezree Abdullah, Mohd; Asyiqin Ahmad, Nurul; Putra Jaya, Ramadhansyah; Hassan, Norhidayah Abdul; Yaacob, Haryati; Rosli Hainin, Mohd

    2017-05-01

    Plastic disposal is one of the major problems for developing countries like Malaysia, at the same time Malaysia needs a large network of roads for its smooth economic and social development. The limited source of bitumen needs a deep thinking to ensure fast road construction. Therefore, the use of plastic waste in road construction not only can help to protect environment but also able to help the road construction industry. The aims of this research are to study the effects of waste plastic on rheological properties of bitumen. Modified bitumen was prepared by using blending techniques. Bitumen was heated and plastic waste was slowly added. Rheological properties of bitumen were performance by penetration, softening point, viscosity and direct shear rheometer test. The results showed that when content of plastic waste increase, the penetration value, softening point and viscosity of bitumen also increase. Generally, plastic waste improves the performance of bitumen when it was added into bitumen. It can be said that the usage helps to improve the performance of the road pavement which also reduces the rutting effect.

  15. Characterisation of plastic packaging waste for recycling: problems related to current approaches

    DEFF Research Database (Denmark)

    Götze, Ramona; Astrup, Thomas Fruergaard

    2013-01-01

    were addressed by a resin type-based sorting analysis and a washing test for plastic packaging material from Danish household waste. Preliminary results show that, for a quarter of the hand sorted material, no resin type could be identified and that Polypropylene and Polyethylene terephthalate were...... criteria of recycling processes. A lack of information in current waste characterisation practise on polymer resin composition, black coloured material content and the influence of surface adherent material on physico-chemical characteristics of plastic packaging waste were identified. These shortcomings...... the dominating resin types in plastic packaging. The suggested washing procedure caused a decrease of 70% of the ash content of the plastic material. The analysed metals and nutrients were reduced by up to 24%...

  16. Thermal recycling of plastic waste using pyrolysis-gasification process for energy production

    Energy Technology Data Exchange (ETDEWEB)

    Forbit, George Teke

    2012-04-04

    The disposal of mixed waste in landfills, dump sites and open burning without material and energy recovery leads to resource loss, causes health problems, pollution and littering. Increasing energy demand for industrial and domestic application with rising costs due to scarcity motivates a constant search for alternative clean energy sources. Recovering energy from waste presents various incentives e.g. creating jobs, alleviating poverty, combating and mitigating climate change, protecting the environment and reducing dependence on traditional fuels sources. Hence, plastics end up in landfills, surface waters and ocean bed with serious negative impact on terrestrial and aquatic biodiversity. Plastic waste with high calorific value (36-46MJ/kg) occupies the greatest portion of landfill space. Hence, using an appropriate technology to transform waste plastic to a hot gaseous mixture which is burned in-situ produces enormous amount of energy without pollution. Based on this hypothesis, the study objectives accomplished were to: 1. Characterise, quantify and classify waste fractions and plastic components common in MSW by manual sorting 2. Evaluate options for sustainable plastic waste management especially for developing countries 3. Design, construct, test and optimize an appropriate technology that applies pyrolysis and gasification processes to convert non-PVC plastic waste to energy 4. Assess the efficiency of the technology based on the functioning, the engineering, mass and energy analysis including socioeconomic and environmental impacts An integrated methodology involving review of current literature, field and laboratory experiments on mixed waste and plastic waste analysis was used. In addition, the pyrolysis-gasification technology (PGT) was conceptualised, designed, constructed, tested and optimised at BTU Cottbus, Germany; Lagos, Nigeria and Dschang, Cameroon. Field studies involving natural observation, interviews, personal discussions and visits to

  17. 热塑性酚醛树脂合成中废水游离酚含量的测定方法%The Method for Determination of Free Phenol Content in Waste Water During Thermal Plastic Phenol-Formaldehyde Resin Synthesis Process

    Institute of Scientific and Technical Information of China (English)

    张苏静; 黄仁和

    2013-01-01

    工业生产中,热塑性酚醛树脂的合成过程会产生大量废水,废水中含有部分游离态的苯酚、甲醛,为了合理回收利用废水,需要对游离酚含量进行测定.本文比较并分析了目前现有的两种不同的测定游离酚的方法,得出用溴量法更适合于测定废水中的游离酚,该方法准确度及精确度较高,适合测定热塑性酚醛树脂废水中的游离酚含量.将合成过程产生的废水分步脱出,用溴量法测定其酚含量,然后将分步脱出的废水采取不同方法再回收使用.%In industrial production, the synthesizing process of thermoplastic phenol-formaldehyde resin will produce large quantities of waste water, which contains part of free phenol and formaldehyde. In order to recycle the waste water reasonably, it is necessary to determine the content of free phenol. This paper compares and analyzes the two methods of determining free phenol content nowadays. The analysis results show that bromometry is better for the determination. It has high accuracy, and bromometry is suitable for determining the free phenol content in the thermal plastic phenol-formaldehyde resin waste water. Free phenol content that occur during the fractional dewatering step is determined by bromometry, and the waste water of different dewatering step is recycled by different methods.

  18. A review on thermal and catalytic pyrolysis of plastic solid waste (PSW).

    Science.gov (United States)

    Al-Salem, S M; Antelava, A; Constantinou, A; Manos, G; Dutta, A

    2017-04-03

    Plastic plays an important role in our daily lives due to its versatility, light weight and low production cost. Plastics became essential in many sectors such as construction, medical, engineering applications, automotive, aerospace, etc. In addition, economic growth and development also increased our demand and dependency on plastics which leads to its accumulation in landfills imposing risk on human health, animals and cause environmental pollution problems such as ground water contamination, sanitary related issues, etc. Hence, a sustainable and an efficient plastic waste treatment is essential to avoid such issues. Pyrolysis is a thermo-chemical plastic waste treatment technique which can solve such pollution problems, as well as, recover valuable energy and products such as oil and gas. Pyrolysis of plastic solid waste (PSW) has gained importance due to having better advantages towards environmental pollution and reduction of carbon footprint of plastic products by minimizing the emissions of carbon monoxide and carbon dioxide compared to combustion and gasification. This paper presents the existing techniques of pyrolysis, the parameters which affect the products yield and selectivity and identify major research gaps in this technology. The influence of different catalysts on the process as well as review and comparative assessment of pyrolysis with other thermal and catalytic plastic treatment methods, is also presented.

  19. Study on Mechanical Properties of Concrete Using Plastic Waste as an Aggregate

    Science.gov (United States)

    Jaivignesh, B.; Sofi, A.

    2017-07-01

    Disposal of large quantity of plastic causes land, water and air pollution etc.., so a study is conducted to recycle the plastic in concrete. This work investigates about the replacement of natural aggregate with non-biodegradable plastic aggregate made up of mixed plastic waste in concrete. Several tests are conducted such as compressive strength of cube, split tensile strength of cylinder, flexural strength test of prism to identify the properties and behavior of concrete using plastic aggregate. Replacement of fine aggregate weight by 10%, 15%, 20% with Plastic fine (PF) aggregate and for each replacement of fine aggregate 15%, 20%, 25% of coarse aggregate replacement also conducted with Plastic Coarse(PC) aggregate. In literatures reported that the addition of plastic aggregate in concrete causes the reduction of strength in concrete due to poor bonding between concrete and plastic aggregate, so addition of 0.3% of steel fiber by weight of cement in concrete is done to improve the concrete strength. Totally 60 cubes, 60 cylinders and 40 prisms are casted to identify the compressive strength, split tensile strength and flexural strength respectively. Casted specimens are tested at 7 and 28 days. The identified results from concrete using plastic aggregate are compared with conventional concrete. Result shows that reduction in mechanical properties of plastic aggregate added concrete. This reduction in strength is mainly due to poor bond strength between cement and plastic aggregate.

  20. Production of Methane and Water from Crew Plastic Waste

    Science.gov (United States)

    Captain, Janine; Santiago, Eddie; Parrish, Clyde; Strayer, Richard F.; Garland, Jay L.

    2008-01-01

    Recycling is a technology that will be key to creating a self sustaining lunar outpost. The plastics used for food packaging provide a source of material that could be recycled to produce water and methane. The recycling of these plastics will require some additional resources that will affect the initial estimate of starting materials that will have to be transported from earth, mainly oxygen, energy and mass. These requirements will vary depending on the recycling conditions. The degredation products of these plastics will vary under different atmospheric conditions. An estimate of the the production rate of methane and water using typical ISRU processes along with the plastic recycling will be presented.

  1. Determining the bio-based content of bio-plastics used in Thailand by radiocarbon analysis

    Science.gov (United States)

    Ploykrathok, T.; Chanyotha, S.

    2017-06-01

    Presently, there is an increased interest in the development of bio-plastic products from agricultural materials which are biodegradable in order to reduce the problem of waste disposal. Since the amount of modern carbon in bio-plastics can indicate how much the amount of agricultural materials are contained in the bio-plastic products, this research aims to determine the modern carbon in bio-plastic using the carbon dioxide absorption method. The radioactivity of carbon-14 contained in the sample is measured by liquid scintillation counter (Tri-carb 3110 TR, PerkinElmer). The percentages of bio-based content in the samples were determined by comparing the observed modern carbon content with the values contained in agricultural raw materials. The experimental results show that only poly(lactic acid) samples have the modern carbon content of 97.4%, which is close to the agricultural materials while other bio-plastics types are found to have less than 50% of the modern carbon content. In other words, most of these bio-plastic samples were mixed with other materials which are not agriculturally originated.

  2. Listed waste determination report. Environmental characterization

    Energy Technology Data Exchange (ETDEWEB)

    1993-06-01

    On September 23, 1988, the US Environmental Protection Agency (EPA) published a notice clarifying interim status requirements for the management of radioactive mixed waste thereby subjecting the Idaho National Engineering Laboratory (INEL) and other applicable Department of Energy (DOE) sites to regulation under the Resource Conservation and Recovery Act (RCRA). Therefore, the DOE was required to submit a Part A Permit application for each treatment, storage, and disposal (TSD) unit within the INEL, defining the waste codes and processes to be regulated under RCRA. The September 1990 revised Part A Permit application, that was approved by the State of Idaho identified 101 potential acute and toxic hazardous waste codes (F-, P-, and U- listed wastes according to 40 CFR 261.31 and 40 CFR 261.33) for some TSD units at the Idaho Chemical Processing Plant. Most of these waste were assumed to have been introduced into the High-level Liquid Waste TSD units via laboratory drains connected to the Process Equipment Waste (PEW) evaporator (PEW system). At that time, a detailed and systematic evaluation of hazardous chemical use and disposal practices had not been conducted to determine if F-, P-, or Unlisted waste had been disposed to the PEW system. The purpose of this investigation was to perform a systematic and detailed evaluation of the use and disposal of the 101 F-, P-, and Unlisted chemicals found in the approved September 1990 Part A Permit application. This investigation was aimed at determining which listed wastes, as defined in 40 CFR 261.31 (F-listed) and 261.33 (P & Unlisted) were discharged to the PEW system. Results of this investigation will be used to support revisions to the RCRA Part A Permit application.

  3. Listed waste determination report. Environmental characterization

    Energy Technology Data Exchange (ETDEWEB)

    1993-06-01

    On September 23, 1988, the US Environmental Protection Agency (EPA) published a notice clarifying interim status requirements for the management of radioactive mixed waste thereby subjecting the Idaho National Engineering Laboratory (INEL) and other applicable Department of Energy (DOE) sites to regulation under the Resource Conservation and Recovery Act (RCRA). Therefore, the DOE was required to submit a Part A Permit application for each treatment, storage, and disposal (TSD) unit within the INEL, defining the waste codes and processes to be regulated under RCRA. The September 1990 revised Part A Permit application, that was approved by the State of Idaho identified 101 potential acute and toxic hazardous waste codes (F-, P-, and U- listed wastes according to 40 CFR 261.31 and 40 CFR 261.33) for some TSD units at the Idaho Chemical Processing Plant. Most of these waste were assumed to have been introduced into the High-level Liquid Waste TSD units via laboratory drains connected to the Process Equipment Waste (PEW) evaporator (PEW system). At that time, a detailed and systematic evaluation of hazardous chemical use and disposal practices had not been conducted to determine if F-, P-, or Unlisted waste had been disposed to the PEW system. The purpose of this investigation was to perform a systematic and detailed evaluation of the use and disposal of the 101 F-, P-, and Unlisted chemicals found in the approved September 1990 Part A Permit application. This investigation was aimed at determining which listed wastes, as defined in 40 CFR 261.31 (F-listed) and 261.33 (P & Unlisted) were discharged to the PEW system. Results of this investigation will be used to support revisions to the RCRA Part A Permit application.

  4. From waste plastics to industrial raw materials: A life cycle assessment of mechanical plastic recycling practice based on a real-world case study.

    Science.gov (United States)

    Gu, Fu; Guo, Jianfeng; Zhang, Wujie; Summers, Peter A; Hall, Philip

    2017-12-01

    Mechanical recycling of waste plastics is an environmental solution to the problem of waste plastic disposal, and has already become a common practice in industry. However, limited information can be found on either the industralised plastic recycling or the recycled materials, despite the use of recycled plastics has already extended to automobile production. This study investigates the life cycle environmental impacts of mechanical plastic recycling practice of a plastic recycling company in China. Waste plastics from various sources, such as agricultural wastes, plastic product manufacturers, collected solid plastic wastes and parts dismantled from waste electric and electronic equipments, are processed in three routes with products end up in different markets. The results of life cycle assessments show that the extrusion process has the largest environmental impacts, followed by the use of fillers and additives. Compared to production of virgin plastics and composites, the mechanical recycling is proved to be a superior alternative in most environmental aspects. Substituting virgin plastic composites with recycled plastic composites has achieved the highest environmental benefits, as virgin composite production has an impact almost 4 times higher that of the recycled composite production in each ReCiPe endpoint damage factor. Sensitivity analysis shows that the coverage of collecting network contribute affect little to overall environmental impact, and centralisation plays an important role in reducing overall environmental impacts. Among the fillers and additives, impact modifiers account for the most significant contributions to the environmental impacts of recycled composites. This study provides necessary information about the existing industrialised plastic recycling practice, and recommendations are given. Research implications are presented with the purpose to achieve higher substitution rate and lower environmental impact. Copyright © 2017 Elsevier B

  5. The usage of plastic waste as a secondary raw material for the modification of sandcrete properties

    Science.gov (United States)

    Klovas, A.; Daukšys, M.; Venčkauskas, L.

    2015-03-01

    Recently the usage of various industry wastes as a secondary raw material tends to increase its relevancy. One of possible options to decrease the amount of waste is to use them to produce new products or materials. The operation of various secondary raw materials (tire rubber, tire cord, ground glass shards, ground ceramic waste products) during the concrete mixture preparation allows to change its as well as cured concrete properties. Recently polymer and steel fibers are used for concrete reinforcement. This study analyses the usage possibility of plastic shavings for the reinforcement of concrete. The technological properties of cement slurry (sand, fraction of 0/4 and 10 kg/m3, 15 kg/m3 and 20 kg/m3 of plastic shavings) as well as mechanical, physical and porosity properties of cured sandcrete were established during the experimental research. The geometric characteristics of mill-shredded plastic shavings were established. Experimental results revealed that the usage of plastic shavings decreased slurry slump and density. The minor decrease of cured sandcrete density (~2200 kg/m3) was noticed with the addition of plastic shavings within the limits of 10 - 20 kg/m3. The flexural strength of cured sandcrete increased from 36 % to 57 % compared with reference specimen (without plastic shavings). The dependence of flexural force and deflection was obtained. Study revealed that the residual strength after crack opening is bigger with the usage of plastic shavings as a secondary raw material compared with reference specimen.

  6. Kinetic studies for catalytic cracking of heavy oil from waste plastics over REY zeolite

    Energy Technology Data Exchange (ETDEWEB)

    Songip, A.R.; Masuda, T.; Kuwahara, H.; Hashimoto, K. (Kyoto University, Kyoto (Japan). Dept. of Chemical Engineering)

    A kinetic model was developed to represent the catalytic cracking of heavy oil from waste plastics by rare-earth metal exchanged Y-type (REY) zeolite to produce gasoline. The influences of reaction conditions on the product distributions were previously reported. On the basis of these results, a reaction pathway was proposed and a set of differential equations was developed. The kinetic parameters were determined by nonlinear least-squares regression of the experimental data. These parameters were found to be proportional to the amount of strong acid sites of the used catalysts. The calculated values of the product distribution were found to be in good agreement with the experimental data. 15 refs., 6 figs., 4 tabs.

  7. Treatment and plastic wastes management. New Ways; Tratamiento y gestion de residuos plasticos agricolas. Nuevas iniciativas

    Energy Technology Data Exchange (ETDEWEB)

    Garcia, M. J.

    2001-07-01

    The continuous improvement of the intensive agriculture in the south of Spain have increased the amount of plastic waste. The solution the authorities proposed and developed has been the mechanical recycling. Since 1992 two facilities have been installed in two zones of high waste generation. These are managed by EGMASA and have achieved a granule quality recognized by the recycled materials market, being used mainly in pipes and bags fabrication. A new application to produce an agglomerate for decking products has been developed and a new facility was constructed in one of the former plants. The new installation is producing 70 ton/day of LDPE form greenhouse plastic waste and post.consumer plastic of selective recollection. (Author)

  8. Conversion of Hazardous Motor Vehicle Used Tire and Polystyrene Waste Plastic Mixture into useful Chemical Products

    Directory of Open Access Journals (Sweden)

    Moinuddin Sarker

    2014-02-01

    Full Text Available Motor vehicle used tire and polystyrene waste plastic mixture into fuel recovery using thermal degradation process in laboratory batch process. Motor vehicle used tire and polystyrene waste plastic was use 75 gm by weight. Motor vehicle tire was 25 gm and polystyrene waste plastic was 50 gm. In presence of oxygen experiment was performed under laboratory fume hood. Thermal degradation temperature range was 100 - 420 oC and experiment run time was 5 hours. Product fuel density is 0.84 gm/ml and liquid fuel conversion rate was 54.93 %. Fuel was analysis by GC/MS and compounds are present aliphatic group, aromatic group, alcoholic group, oxygen content and nitrogen content.Fuel can use refinery process as a refinery feed.Keywords: Tire, polystyrene, conversion, chemical product, vehicle, hydrocarbon

  9. Design of an innovative, ecological portable waste compressor for in-house recycling of paper, plastic and metal packaging waste.

    Science.gov (United States)

    Xevgenos, D; Athanasopoulos, N; Kostazos, P K; Manolakos, D E; Moustakas, K; Malamis, D; Loizidou, M

    2015-05-01

    Waste management in Greece relies heavily on unsustainable waste practices (mainly landfills and in certain cases uncontrolled dumping of untreated waste). Even though major improvements have been achieved in the recycling of municipal solid waste during recent years, there are some barriers that hinder the achievement of high recycling rates. Source separation of municipal solid waste has been recognised as a promising solution to produce high-quality recycled materials that can be easily directed to secondary materials markets. This article presents an innovative miniature waste separator/compressor that has been designed and developed for the source separation of municipal solid waste at a household level. The design of the system is in line with the Waste Framework Directive (2008/98/EC), since it allows for the separate collection (and compression) of municipal solid waste, namely: plastic (polyethylene terephthalate and high-density polyethylene), paper (cardboard and Tetrapak) and metal (aluminium and tin cans). It has been designed through the use of suitable software tools (LS-DYNA, INVENTROR and COMSOL). The results from the simulations, as well as the whole design process and philosophy, are discussed in this article. © The Author(s) 2015.

  10. Separation of polyethylene terephthalate from municipal waste plastics by froth flotation for recycling industry.

    Science.gov (United States)

    Wang, Chong-Qing; Wang, Hui; Liu, You-Nian

    2015-01-01

    Recycling is an effective way to manage plastic wastes and receives considerable attention. Since plastic mixtures are difficult to recycle because of their intrinsic characteristics, separation of mixed plastics is the key problem for recycling. Separation of polyethylene terephthalate (PET) from municipal waste plastics (MWP) by froth flotation combined with alkaline pretreatment was investigated for recycling industry. The effect of process variables was estimated by L9 (3(4)) orthogonal array of experiments and single factor experiments. The optimum conditions of alkaline pretreatment are 10 wt% sodium hydroxide, 20 min and 70°C. After alkaline pretreatment under optimum conditions, flotation separation PET from acrylonitrile-butadiene-styrene, polystyrene, polycarbonate or polyvinyl chloride was achieved with high purity and efficiency. The purity of PET is up to 98.46% and the recovery is above 92.47%. A flow sheet of separation PET from MWP by a combination of froth flotation and sink float separation was designed. This study facilitates industrial application of plastics flotation and provides technical insights into recycling of waste plastics. Copyright © 2014 Elsevier Ltd. All rights reserved.

  11. Separation of polyethylene terephthalate from municipal waste plastics by froth flotation for recycling industry

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Chong-Qing; Wang, Hui, E-mail: huiwang1968@163.com; Liu, You-Nian

    2015-01-15

    Highlights: • Factors of NaOH treatment were studied by orthogonal and single factor experiments. • Mechanism of alkaline treatment for facilitating flotation was manifested. • Flotation separation of PET was achieved with high purity and efficiency. • A flow sheet of purification PET from MWP was designed. - Abstract: Recycling is an effective way to manage plastic wastes and receives considerable attention. Since plastic mixtures are difficult to recycle because of their intrinsic characteristics, separation of mixed plastics is the key problem for recycling. Separation of polyethylene terephthalate (PET) from municipal waste plastics (MWP) by froth flotation combined with alkaline pretreatment was investigated for recycling industry. The effect of process variables was estimated by L{sub 9} (3{sup 4}) orthogonal array of experiments and single factor experiments. The optimum conditions of alkaline pretreatment are 10 wt% sodium hydroxide, 20 min and 70 °C. After alkaline pretreatment under optimum conditions, flotation separation PET from acrylonitrile–butadiene–styrene, polystyrene, polycarbonate or polyvinyl chloride was achieved with high purity and efficiency. The purity of PET is up to 98.46% and the recovery is above 92.47%. A flow sheet of separation PET from MWP by a combination of froth flotation and sink float separation was designed. This study facilitates industrial application of plastics flotation and provides technical insights into recycling of waste plastics.

  12. The synthesis of nanostructured SiC from waste plastics and silicon powder

    Science.gov (United States)

    Ju, Zhicheng; Xu, Liqiang; Pang, Qiaolian; Xing, Zheng; Ma, Xiaojian; Qian, Yitai

    2009-09-01

    Waste plastics constitute a growing environmental problem. Therefore, the treatment of waste plastics should be considered. Here we synthesize 3C-SiC nanomaterials coexisting with amorphous graphite particles utilizing waste plastics and Si powder at 350-500 °C in a stainless steel autoclave. 3C-SiC could be finally obtained after refluxing with aqueous HClO4 (70 wt%) at 180 °C. X-ray powder diffraction patterns indicate that the product is 3C-SiC with the calculated lattice constant a = 4.36 Å. Transmission electron microscopy (TEM) images show that the SiC samples presented two morphologies: hexagonal platelets prepared by the waste detergent bottles or beverage bottles and nanowires prepared by waste plastic bags respectively. The corresponding selected area electron diffraction (SAED) pattern indicates that either the entire hexagonal platelet or the nanowire is single crystalline. High-resolution TEM shows the planar surfaces of the SiC platelet correspond to {111} planes; the lateral surfaces are {110} planes and the preferential growth direction of the nanowires is along [111]. The output of SiC was ~39% based on the amount of Si powder.

  13. Recycling and disposal of plastics waste in South Africa

    CSIR Research Space (South Africa)

    Nurse, RH

    1976-06-01

    Full Text Available wastes, the National Programme also includes research relating to ecosystems, their structure, functioning and exploitation and disturbance by man. It includes research relating to environmental problems in inland waters, terrestrial ecosystems, the sea...

  14. An analysis of the composition and metal contamination of plastics from waste electrical and electronic equipment (WEEE)

    Energy Technology Data Exchange (ETDEWEB)

    Stenvall, Erik, E-mail: erik.stenvall@chalmers.se [Department of Materials and Manufacturing Technology, Chalmers University of Technology, 41296 Göteborg (Sweden); Tostar, Sandra [Department of Industrial Materials Recycling, Chalmers University of Technology, 41296 Göteborg (Sweden); Boldizar, Antal [Department of Materials and Manufacturing Technology, Chalmers University of Technology, 41296 Göteborg (Sweden); Foreman, Mark R.StJ. [Department of Industrial Materials Recycling, Chalmers University of Technology, 41296 Göteborg (Sweden); Möller, Kenneth [Chemistry and Materials Technology, SP, 50115 Borås (Sweden)

    2013-04-15

    The compositions of three WEEE plastic batches of different origin were investigated using infrared spectroscopy, and the metal content was determined with inductively coupled plasma. The composition analysis of the plastics was based mainly on 14 samples collected from a real waste stream, and showed that the major constituents were high impact polystyrene (42 wt%), acrylonitrile–butadiene–styrene copolymer (38 wt%) and polypropylene (10 wt%). Their respective standard deviations were 21.4%, 16.5% and 60.7%, indicating a considerable variation even within a single batch. The level of metal particle contamination was found to be low in all samples, whereas wood contamination and rubber contamination were found to be about 1 wt% each in most samples. In the metal content analysis, iron was detected at levels up to 700 ppm in the recyclable waste plastics fraction, which is of concern due to its potential to catalyse redox reactions during melt processing and thus accelerate the degradation of plastics during recycling. Toxic metals were found only at very low concentrations, with the exception of lead and cadmium which could be detected at 200 ppm and 70 ppm levels, respectively, but these values are below the current threshold limits of 1000 ppm and 100 ppm set by the Restriction of Hazardous Substances directive.

  15. An analysis of the composition and metal contamination of plastics from waste electrical and electronic equipment (WEEE).

    Science.gov (United States)

    Stenvall, Erik; Tostar, Sandra; Boldizar, Antal; Foreman, Mark R StJ; Möller, Kenneth

    2013-04-01

    The compositions of three WEEE plastic batches of different origin were investigated using infrared spectroscopy, and the metal content was determined with inductively coupled plasma. The composition analysis of the plastics was based mainly on 14 samples collected from a real waste stream, and showed that the major constituents were high impact polystyrene (42 wt%), acrylonitrile-butadiene-styrene copolymer (38 wt%) and polypropylene (10 wt%). Their respective standard deviations were 21.4%, 16.5% and 60.7%, indicating a considerable variation even within a single batch. The level of metal particle contamination was found to be low in all samples, whereas wood contamination and rubber contamination were found to be about 1 wt% each in most samples. In the metal content analysis, iron was detected at levels up to 700 ppm in the recyclable waste plastics fraction, which is of concern due to its potential to catalyse redox reactions during melt processing and thus accelerate the degradation of plastics during recycling. Toxic metals were found only at very low concentrations, with the exception of lead and cadmium which could be detected at 200 ppm and 70 ppm levels, respectively, but these values are below the current threshold limits of 1000 ppm and 100 ppm set by the Restriction of Hazardous Substances directive. Copyright © 2013 Elsevier Ltd. All rights reserved.

  16. Influence of uncoated and coated plastic waste coarse aggregates to concrete compressive strength

    Directory of Open Access Journals (Sweden)

    Purnomo Heru

    2017-01-01

    Full Text Available The use of plastic waste as coarse aggregates in concrete is part of efforts to reduce environmental pollution. In one hand the use of plastic as aggregates can provide lighter weight of the concrete than concrete using natural aggregates, but on the other hand bond between plastic coarse aggregates and hard matrix give low concrete compressive strength. Improvement of the bond between plastic coarse aggregate and hard matrix through a sand coating to plastic coarse aggregate whole surface is studied. Sand used to coat the plastic aggregates are Merapi volcanic sand which are taken in Magelang. Three mixtures of polypropylene (PP coarse plastic aggregates, Cimangkok river sand as fine aggregates, water and Portland Cement Composite with a water-cement ratio of 0.28, 0.3 and 0.35 are conducted. Compression test are performed on concrete cylindrical specimens with a diameter of 10 cm and a height of 20 cm. The results in general show that concrete specimens using plastic aggregates coated with sand have higher compressive strength compared to those of concrete specimens using plastic aggregates without sand coating. The bond improvement is indirectly indicated by the betterment of concrete compressive strength.

  17. Rheological behaviour of coal modified by waste plastics and lubricating oils

    OpenAIRE

    Melendi Espina, Sonia; Díez Díaz-Estébanez, María Antonia; Álvarez García, Ramón; Castro, Miguel; Steel, Karen; Snape, Colin E.

    2007-01-01

    The aim of this work is to study the interactions between a coking coal and two types of wastes: plastics from municipal wastes (single and mixed) and lubricating-oils coming from the iron and steel sector. For this purpose, Gieseler plastometry, rheometry and in situ high-temperature 1H NMR spectroscopy can be combined to discern the most suitable wastes for using as secondary raw materials in metallurgical coke production. It was found that there is a relationship between the Gieseler fl...

  18. The valorization of the plastic waste to the rheological characteristics of bituminous mixtures

    Science.gov (United States)

    Boucherba, Mohammed; Kriker, Abdelouahed; Kebaili, Nabil

    2017-02-01

    The valorization of materials used at the end of the cycle currently constitutes one of the major challenges for the state for the safeguarding of the environment. Indeed, plastic waste from their obstruction and weak biodegradability often constitutes a threat for health, nature and the environment. The present study treats a mining method and valorization of these wastes in the road, where this waste is incorporated in the pure bitumen of asphalt concretes using the Dry process. The vital objective of this work is to see their impact on the mechanical behavior of these concretes using the Marshall Test and NAT.

  19. Ammonia modification for flotation separation of polycarbonate and polystyrene waste plastics.

    Science.gov (United States)

    Wang, Chong-qing; Wang, Hui; Gu, Guo-hua; Lin, Qing-quan; Zhang, Ling-ling; Huang, Luo-luo; Zhao, Jun-yao

    2016-05-01

    A promising method, ammonia modification, was developed for flotation separation of polycarbonate (PC) and polystyrene (PS) waste plastics. Ammonia modification has little effect on flotation behavior of PS, while it changes significantly that of PC. The PC recovery in the floated product drops from 100% to 3.17% when modification time is 13min and then rises to 100% after longer modification. The mechanism of ammonia modification was studied by contact angle, and Fourier transform infrared (FT-IR) and X-ray photoelectron spectroscopy (XPS) measurements. Contact angle of PC indicates the decline of PC recovery in the floated product is ascribed to an increase in surface wettability. FT-IR and XPS spectra suggest that ammonia modification causes chemical reactions occurred on PC surface. Flotation behavior of ammonia-modified PC and PS was investigated with respect to flotation time, frother concentration and particle sizes. Flotation separation of PC and PS waste plastics was conducted based on the flotation behavior of single plastic. PC and PS mixtures with different particle sizes are separated efficiently, implying that the technology possesses superior applicability to particle sizes of plastics. The purity of PS and PC is up to 99.53% and 98.21%, respectively, and the recovery of PS and PC is larger than 92.06%. A reliable, cheap and effective process is proposed for separation of PC and PS waste plastics.

  20. Comprehensive utilization of waste plastics%废旧塑料的综合利用

    Institute of Scientific and Technical Information of China (English)

    吴自强; 许士洪; 刘志宏

    2001-01-01

    Plastic materials are used widely in many fields of national economy because of its excellent properties.These waste plastics not only pollute the environment but also waste seriously the resources.This paper reviews briefly the importance and the progress of the comprehensive utilization of waste plastics in some fields,such as direct utilization,utilization after its modification,thermal decomposition and coal liquefaction combined with it(co-liquefacation).It is pointed out that the co-liquefaction is the most promising way to utilize the waste plastics,and it will become a hot point in further research work.%综合利用废旧塑料,解决“白色污染”,已成为全球的研究热点。本文从废旧塑料的直接利用、改性利用、热分解、与煤共液化等几个方面综述了废旧塑料的综合利用途径,其中废旧塑料与煤共液化处理技术很有发展前途,将成为今后研究的新热点。

  1. Energy and raw material saving through recycling of plastics materials extracted from urban waste. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Michaux, J.

    The study is divided into 3 parts: Technical feasibility study, economic feasibility study, study of a factory handling 2,400 tons/year of plastics waste, and technico-economic feasibility study and market research, with an analysis of energy savings.

  2. Techno-economic evaluation of high temperature pyrolysis processes for mixed plastic waste.

    NARCIS (Netherlands)

    Westerhout, R.W.J.; Koningsbruggen, van M.P.; Ham, van der A.G.J.; Kuipers, J.A.M.; Swaaij, van W.P.M.

    1998-01-01

    Three pyrolysis processes for Mixed Plastic Waste (MPW) with different reactors (Bubbling Fluidized Bed, Circulating Fluidized Bed and Rotating Cone Reactor, respectively BFB, CFB and RCR) were designed and evaluated. The estimated fixed capital investment for a 50 kton/year MPW pyrolysis plant buil

  3. Processing and properties of a solid energy fuel from municipal solid waste (MSW) and recycled plastics.

    Science.gov (United States)

    Gug, JeongIn; Cacciola, David; Sobkowicz, Margaret J

    2015-01-01

    Diversion of waste streams such as plastics, woods, papers and other solid trash from municipal landfills and extraction of useful materials from landfills is an area of increasing interest especially in densely populated areas. One promising technology for recycling municipal solid waste (MSW) is to burn the high-energy-content components in standard coal power plant. This research aims to reform wastes into briquettes that are compatible with typical coal combustion processes. In order to comply with the standards of coal-fired power plants, the feedstock must be mechanically robust, free of hazardous contaminants, and moisture resistant, while retaining high fuel value. This study aims to investigate the effects of processing conditions and added recyclable plastics on the properties of MSW solid fuels. A well-sorted waste stream high in paper and fiber content was combined with controlled levels of recyclable plastics PE, PP, PET and PS and formed into briquettes using a compression molding technique. The effect of added plastics and moisture content on binding attraction and energy efficiency were investigated. The stability of the briquettes to moisture exposure, the fuel composition by proximate analysis, briquette mechanical strength, and burning efficiency were evaluated. It was found that high processing temperature ensures better properties of the product addition of milled mixed plastic waste leads to better encapsulation as well as to greater calorific value. Also some moisture removal (but not complete) improves the compacting process and results in higher heating value. Analysis of the post-processing water uptake and compressive strength showed a correlation between density and stability to both mechanical stress and humid environment. Proximate analysis indicated heating values comparable to coal. The results showed that mechanical and moisture uptake stability were improved when the moisture and air contents were optimized. Moreover, the briquette

  4. Development of a new approach based on midwave infrared spectroscopy for post-consumer black plastic waste sorting in the recycling industry.

    Science.gov (United States)

    Rozenstein, Offer; Puckrin, Eldon; Adamowski, Jan

    2017-10-01

    Waste sorting is key to the process of waste recycling. Exact identification of plastic resin and wood products using Near Infrared (NIR, 1-1.7µm) sensing is currently in use. Yet, dark targets characterized by low reflectance, such as black plastics, are hard to identify by this method. Following the recent success of Midwave Infrared (MWIR, 3-12µm) measurements to identify coloured plastic polymers, the aim of this study was to assess whether this technique is applicable to sorting black plastic polymers and wood products. We performed infrared reflectance contact measurements of 234 plastic samples and 29 samples of wood and paper products. Plastic samples included black, coloured and transparent Polyethylene Terephthalate (PET), Polyethylene (PE), Polyvinyl Chloride (PVC), Polypropylene (PP), Polylactic acid (PLA) and Polystyrene (PS). The spectral signatures of the black and coloured plastic samples were compared with clear plastic samples and signatures documented in the literature to identify the polymer spectral features in the presence of coloured material. This information was used to determine the spectral bands that best suit the sorting of black plastic polymers. The main NIR-MWIR absorption features of wood, cardboard and paper were identified as well according to the spectral measurements. Good agreement was found between our measurements and the absorption features documented in the literature. The new approach using MWIR spectral features appears to be useful for black plastics as it overcomes some of the limitations in the NIR region to identify them. The main limitation of this technique for industrial applications is the trade-off between the signal-to-noise ratio of the sensor operating in standoff mode and the speed at which waste is moved under the sensor. This limitation can be resolved by reducing the system's spectral resolution to 16cm(-1), which allows for faster spectra acquisition while maintaining a reasonable signal-to-noise ratio

  5. Removal of brominated flame retardant from electrical and electronic waste plastic by solvothermal technique

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Cong-Cong [Research Center For Eco-Environmental Sciences, Chinese Academy of Sciences, 18 Shuangqing Road, Beijing 100085 (China); Zhang, Fu-Shen, E-mail: fszhang@rcees.ac.cn [Research Center For Eco-Environmental Sciences, Chinese Academy of Sciences, 18 Shuangqing Road, Beijing 100085 (China)

    2012-06-30

    Highlights: Black-Right-Pointing-Pointer A process for brominated flame retardants (BFRs) removal in plastic was established. Black-Right-Pointing-Pointer The plastic became bromine-free with the structure maintained after this treatment. Black-Right-Pointing-Pointer BFRs transferred into alcohol solvent were easily debrominated by metallic copper. - Abstract: Brominated flame retardants (BFRs) in electrical and electronic (E and E) waste plastic are toxic, bioaccumulative and recalcitrant. In the present study, tetrabromobisphenol A (TBBPA) contained in this type of plastic was tentatively subjected to solvothermal treatment so as to obtain bromine-free plastic. Methanol, ethanol and isopropanol were examined as solvents for solvothermal treatment and it was found that methanol was the optimal solvent for TBBPA removal. The optimum temperature, time and liquid to solid ratio for solvothermal treatment to remove TBBPA were 90 Degree-Sign C, 2 h and 15:1, respectively. After the treatment with various alcohol solvents, it was found that TBBPA was finally transferred into the solvents and bromine in the extract was debrominated catalyzed by metallic copper. Bisphenol A and cuprous bromide were the main products after debromination. The morphology and FTIR properties of the plastic were generally unchanged after the solvothermal treatment indicating that the structure of the plastic maintained after the process. This work provides a clean and applicable process for BFRs-containing plastic disposal.

  6. Converting Biomass and Waste Plastic to Solid Fuel Briquettes

    Directory of Open Access Journals (Sweden)

    F. Zannikos

    2013-01-01

    Full Text Available This work examines the production of briquettes for household use from biomass in combination with plastic materials from different sources. Additionally, the combustion characteristics of the briquettes in a common open fireplace were studied. It is clear that the geometry of the briquettes has no influence on the smoke emissions. When the briquettes have a small amount of polyethylene terephthalate (PET, the behavior in the combustion is steadier because of the increase of oxygen supply. The smoke levels are between the 3rd and 4th grades of the smoke number scale. Measuring the carbon monoxide emission, it was observed that the burning of the plastic in the mixture with biomass increases the carbon monoxide emissions from 10% to 30% as compared to carbon monoxide emission from sawdust biomass emissions which was used as a reference.

  7. Estimation of packaged water consumption and associated plastic waste production from household budget surveys

    Science.gov (United States)

    Wardrop, Nicola A.; Dzodzomenyo, Mawuli; Aryeetey, Genevieve; Hill, Allan G.; Bain, Robert E. S.; Wright, Jim

    2017-08-01

    Packaged water consumption is growing in low- and middle-income countries, but the magnitude of this phenomenon and its environmental consequences remain unclear. This study aims to quantify both the volumes of packaged water consumed relative to household water requirements and associated plastic waste generated for three West African case study countries. Data from household expenditure surveys for Ghana, Nigeria and Liberia were used to estimate the volumes of packaged water consumed and thereby quantify plastic waste generated in households with and without solid waste disposal facilities. In Ghana, Nigeria and Liberia respectively, 11.3 (95% confidence interval: 10.3-12.4), 10.1 (7.5-12.5), and 0.38 (0.31-0.45) Ml day-1 of sachet water were consumed. This generated over 28 000 tonnes yr-1 of plastic waste, of which 20%, 63% and 57% was among households lacking formal waste disposal facilities in Ghana, Nigeria and Liberia respectively. Reported packaged water consumption provided sufficient water to meet daily household drinking-water requirements for 8.4%, less than 1% and 1.6% of households in Ghana, Nigeria and Liberia respectively. These findings quantify packaged water’s contribution to household water needs in our study countries, particularly Ghana, but indicate significant subsequent environmental repercussions.

  8. Converting Biomass and Waste Plastic to Solid Fuel Briquettes

    OpenAIRE

    Zannikos, F.; Kalligeros, S.; Anastopoulos, G.; Lois, E.

    2013-01-01

    This work examines the production of briquettes for household use from biomass in combination with plastic materials from different sources. Additionally, the combustion characteristics of the briquettes in a common open fireplace were studied. It is clear that the geometry of the briquettes has no influence on the smoke emissions. When the briquettes have a small amount of polyethylene terephthalate (PET), the behavior in the combustion is steadier because of the increase of oxygen supply. T...

  9. adaptation of plastic waste to energy development in lagos

    African Journals Online (AJOL)

    user

    specific months were primarily used as a case study to portray the fact that all measures put in place by ... people. Nigeria seems to have been in energy deficit for a long time and successive .... Aluminium (%) .... process involves core use of Simpson's rule for the ... possible way to inject sanity into waste management.

  10. Ultrasound imaging for quantitative measurement of immersed plastic waste particles

    NARCIS (Netherlands)

    Sanaee, S.A.; Bakker, M.C.M.

    2012-01-01

    Ultrasound imaging techniques are proposed for measuring the shape and thickness of immersed waste particles (10-20 mm size) using a linear sensor array from a fixed position. For these purposes both the front and back surface of a particle needs to be reconstructed. Raw ultrasound pulse-echo and pl

  11. Pyrolysis and dehalogenation of plastics from waste electrical and electronic equipment (WEEE): a review.

    Science.gov (United States)

    Yang, Xiaoning; Sun, Lushi; Xiang, Jun; Hu, Song; Su, Sheng

    2013-02-01

    Plastics from waste electrical and electronic equipment (WEEE) have been an important environmental problem because these plastics commonly contain toxic halogenated flame retardants which may cause serious environmental pollution, especially the formation of carcinogenic substances polybrominated dibenzo dioxins/furans (PBDD/Fs), during treat process of these plastics. Pyrolysis has been proposed as a viable processing route for recycling the organic compounds in WEEE plastics into fuels and chemical feedstock. However, dehalogenation procedures are also necessary during treat process, because the oils collected in single pyrolysis process may contain numerous halogenated organic compounds, which would detrimentally impact the reuse of these pyrolysis oils. Currently, dehalogenation has become a significant topic in recycling of WEEE plastics by pyrolysis. In order to fulfill the better resource utilization of the WEEE plastics, the compositions, characteristics and dehalogenation methods during the pyrolysis recycling process of WEEE plastics were reviewed in this paper. Dehalogenation and the decomposition or pyrolysis of WEEE plastics can be carried out simultaneously or successively. It could be 'dehalogenating prior to pyrolysing plastics', 'performing dehalogenation and pyrolysis at the same time' or 'pyrolysing plastics first then upgrading pyrolysis oils'. The first strategy essentially is the two-stage pyrolysis with the release of halogen hydrides at low pyrolysis temperature region which is separate from the decomposition of polymer matrixes, thus obtaining halogenated free oil products. The second strategy is the most common method. Zeolite or other type of catalyst can be used in the pyrolysis process for removing organohalogens. The third strategy separate pyrolysis and dehalogenation of WEEE plastics, which can, to some degree, avoid the problem of oil value decline due to the use of catalyst, but obviously, this strategy may increase the cost of

  12. DETERMINATION OF DIPOLE MOMENTS IN PLASTICIZER ADDITIONS FOR CEMENT CONCRETES

    Directory of Open Access Journals (Sweden)

    P. I. Ioukhnevsky

    2010-01-01

    Full Text Available The paper contains a method for determination of dipole moments in chemical plasticizer addition molecules for cement concretes as in powder-state so in the form of aqueous solutions as well.The methodology is based on measuring dielectric substance  permittivity depending on temperature, construction of a diagram (ε – 1/(ε + 2 = f(1/T with subsequent calculation of the molecule dipole moment. The Ossipov’s formula has been used for aqueous solutions of super-plasticizer additions with the purpose to calculate a dipole moment of polar substance in the polar solvent.The obtained values of dipole moments in C-3 super-plasticizer addition molecule are in good agreement with the values obtained as a result of quantum-chemical calculations. 

  13. Lightweight Brick by Carbon Ash from The Mixed Plastic Waste Treatment Plant

    Directory of Open Access Journals (Sweden)

    Chen Kuo-Wei

    2016-01-01

    Full Text Available This study was designed to investigate the mixed plastic waste from the production of light carbon ash bricks performance. The mixed waste plastic pyrolysis process generated waste - Carbon ash. After extrusion, a Lightweight brick was made by carbon ash, additive and Cement mortar. In general, the set compressive strength and insulation effect of lightweight bricks with carbon ash proportion for significant impact. The set water absorption and thermal conductivity of lightweight bricks with carbon ash proportion for significant impact. The set density of lightweight brick ameliorates with M3824 additive and CM3 cement mortar for significant impact. Under conditions of technology and economic, the results of this study as reference for market-oriented marketing and commercialization of production.

  14. Task 3 - Pyrolysis of Plastic Waste. Semiannual report, November 1, 1996--March 31, 1997

    Energy Technology Data Exchange (ETDEWEB)

    Ness, Robert O.; Aulich, Ted R.

    1997-12-31

    Over the last 50 years, the U.S. Department of Energy (DOE) has produced a wide variety of radioactive wastes from activities associated with nuclear defense and nuclear power generation. These wastes include low-level radioactive solid wastes, mixed wastes, and transuranic (TRU) wastes. A portion of these wastes consists of high- organic-content materials, such as resins, plastics, and other polymers; synthetic and natural rubbers; cellulosic-based materials; and oils, organic solvents, and chlorinated organic solvents. Many of these wastes contain hazardous and/or pyrophoric materials in addition to radioactive species. Physical forms of the waste include ion-exchange resins used to remove radioactive elements from nuclear reactor cooling water, lab equipment and tools (e.g., measurement and containment vessels, hoses, wrappings, equipment coverings and components, and countertops), oil products (e.g., vacuum pump and lubrication oils), bags and other storage containers (for liquids, solids, and gases), solvents, gloves, lab coats and anti-contamination clothing, and other items. Major polymer and chemical groups found in high-organic-content radioactive wastes include polyvinyl chloride (PVC), low-density polyethylene (LDPE), polypropylene (PP), Teflon(TM), polystyrene (PS), nylon, latex, polyethylene terephthalate (PET), vinyl, high-density polyethylene (HDPE), polycarbonate, nitriles, Tygon(R), butyl, and Tyvec(R).

  15. Processing and properties of a solid energy fuel from municipal solid waste (MSW) and recycled plastics

    Energy Technology Data Exchange (ETDEWEB)

    Gug, JeongIn, E-mail: Jeongin_gug@student.uml.edu; Cacciola, David, E-mail: david_cacciola@student.uml.edu; Sobkowicz, Margaret J., E-mail: Margaret_sobkowiczkline@uml.edu

    2015-01-15

    Highlights: • Briquetting was used to produce solid fuels from municipal solid waste and recycled plastics. • Optimal drying, processing temperature and pressure were found to produce stable briquettes. • Addition of waste plastics yielded heating values comparable with typical coal feedstocks. • This processing method improves utilization of paper and plastic diverted from landfills. - Abstract: Diversion of waste streams such as plastics, woods, papers and other solid trash from municipal landfills and extraction of useful materials from landfills is an area of increasing interest especially in densely populated areas. One promising technology for recycling municipal solid waste (MSW) is to burn the high-energy-content components in standard coal power plant. This research aims to reform wastes into briquettes that are compatible with typical coal combustion processes. In order to comply with the standards of coal-fired power plants, the feedstock must be mechanically robust, free of hazardous contaminants, and moisture resistant, while retaining high fuel value. This study aims to investigate the effects of processing conditions and added recyclable plastics on the properties of MSW solid fuels. A well-sorted waste stream high in paper and fiber content was combined with controlled levels of recyclable plastics PE, PP, PET and PS and formed into briquettes using a compression molding technique. The effect of added plastics and moisture content on binding attraction and energy efficiency were investigated. The stability of the briquettes to moisture exposure, the fuel composition by proximate analysis, briquette mechanical strength, and burning efficiency were evaluated. It was found that high processing temperature ensures better properties of the product addition of milled mixed plastic waste leads to better encapsulation as well as to greater calorific value. Also some moisture removal (but not complete) improves the compacting process and results in

  16. Pyrolysis-catalysis of waste plastic using a nickel-stainless-steel mesh catalyst for high-value carbon products.

    Science.gov (United States)

    Zhang, Yeshui; Nahil, Mohamad A; Wu, Chunfei; Williams, Paul T

    2017-02-03

    A stainless-steel mesh loaded with nickel catalyst was produced and used for the pyrolysis-catalysis of waste high-density polyethylene with the aim of producing high-value carbon products, including carbon nanotubes (CNTs). The catalysis temperature and plastic-to-catalyst ratio were investigated to determine the influence on the formation of different types of carbon deposited on the nickel-stainless-steel mesh catalyst. Increasing temperature from 700 to 900°C resulted in an increase in the carbon deposited on the nickel-loaded stainless-steel mesh catalyst from 32.5 to 38.0 wt%. The increase in sample-to-catalyst ratio reduced the amount of carbon deposited on the mesh catalyst in terms of g carbon g(-1) plastic. The carbons were found to be largely composed of filamentous carbons, with negligible disordered (amorphous) carbons. Transmission electron microscopy analysis of the filamentous carbons revealed them to be composed of a large proportion (estimated at ∼40%) multi-walled carbon nanotubes (MWCNTs). The optimum process conditions for CNT production, in terms of yield and graphitic nature, determined by Raman spectroscopy, was catalysis temperature of 800°C and plastic-to-catalyst ratio of 1:2, where a mass of 334 mg of filamentous/MWCNTs g(-1) plastic was produced.

  17. Thermal recycling of plastic waste using pyrolysis-gasification process for energy production

    Energy Technology Data Exchange (ETDEWEB)

    Forbit, George Teke

    2012-04-04

    The disposal of mixed waste in landfills, dump sites and open burning without material and energy recovery leads to resource loss, causes health problems, pollution and littering. Increasing energy demand for industrial and domestic application with rising costs due to scarcity motivates a constant search for alternative clean energy sources. Recovering energy from waste presents various incentives e.g. creating jobs, alleviating poverty, combating and mitigating climate change, protecting the environment and reducing dependence on traditional fuels sources. Hence, plastics end up in landfills, surface waters and ocean bed with serious negative impact on terrestrial and aquatic biodiversity. Plastic waste with high calorific value (36-46MJ/kg) occupies the greatest portion of landfill space. Hence, using an appropriate technology to transform waste plastic to a hot gaseous mixture which is burned in-situ produces enormous amount of energy without pollution. Based on this hypothesis, the study objectives accomplished were to: 1. Characterise, quantify and classify waste fractions and plastic components common in MSW by manual sorting 2. Evaluate options for sustainable plastic waste management especially for developing countries 3. Design, construct, test and optimize an appropriate technology that applies pyrolysis and gasification processes to convert non-PVC plastic waste to energy 4. Assess the efficiency of the technology based on the functioning, the engineering, mass and energy analysis including socioeconomic and environmental impacts An integrated methodology involving review of current literature, field and laboratory experiments on mixed waste and plastic waste analysis was used. In addition, the pyrolysis-gasification technology (PGT) was conceptualised, designed, constructed, tested and optimised at BTU Cottbus, Germany; Lagos, Nigeria and Dschang, Cameroon. Field studies involving natural observation, interviews, personal discussions and visits to

  18. A new technology proposed to recycle waste plastics into hydrocarbon fuel in USA

    Directory of Open Access Journals (Sweden)

    Moinuddin Sarker, Mohammad Mamunor Rashid, Mohammed Molla, Muhammad Sadikur Rahman

    2012-01-01

    Full Text Available Energy crisis and environmental degradation by polymer wastes have been imperative to find and propose technologies for recovery of raw materials and energy from non-conventional sources like plastic wastes. A variety of methods and processes connected with global or national policies have been proposed worldwide. A new type of steel reactor is proposed for conversion of waste plastics to fuel like mixture of hydrocarbons. The results of the thermal degradation of waste plastics in the laboratory scale set-up based on this process in the paper. The melting and thermal cracking processes were carried out in a single batch process at the temperature range is 200–420 ºC. The final product consisted of light gas 6.3 % and liquid product 90%. 3.7% solid black products were produced. The light, ‘‘gas” fraction of the hydrocarbons mixture (C1–C4 and rest of liquid fuel made over 90% of the liquid product. It may be used for fuel production refinery or electricity generation.

  19. Prospect of Technology of Recycling Waste Plastics%废旧塑料回收利用技术展望

    Institute of Scientific and Technical Information of China (English)

    董莲枝; 郭健; 靳新慧

    2012-01-01

    In this paper, the authors introduced progress technologies of recycling common waste plastics, and put forward ex- isting problems of waste plastics and cross-linking agent in chemical modification of waste plastics.%介绍了常见的废旧塑料回收利用和回收方式的技术进展,提出在废旧塑料的化学改性中存在的问题及交联剂的选择。

  20. RoHS regulated substances in mixed plastics from waste electrical and electronic equipment.

    Science.gov (United States)

    Wäger, Patrick A; Schluep, Mathias; Müller, Esther; Gloor, Rolf

    2012-01-17

    The disposal and recovery of plastics from waste electrical and electronic equipment (WEEE) are of considerable importance, both from an environmental and an economic perspective. This paper presents the results of a study investigating current concentrations of hazardous substances in mixed plastics from WEEE and their implications for an environmentally sound recovery. The study included 53 sampling campaigns for mixed plastics from WEEE. The samples were analyzed with regard to heavy metals (cadmium, chromium, mercury, and lead) and flame retardants (PentaBDE, OctaBDE, DecaBDE, DecaBB) regulated in the RoHS Directive. Besides these substances, other brominated flame retardants known to occur in electronics (HBCD, TBBPA) as well as the total bromine and phosphorus contents were considered. Results show that no mixed plastics fraction from WEEE is completely free from substances regulated in the RoHS Directive. The lowest number and average concentrations were found in flat screen monitors. The highest concentrations were found in mixed plastics from CRT monitors and TVs. Mixed plastics fractions with high average concentrations of heavy metals originate from the treatment of small household appliances (cadmium), ICT equipment (lead), and consumer equipment (lead). Mixed plastics fractions with high average concentrations of brominated flame retardants mainly originate from the treatment of small household appliances for high temperature applications (DecaBDE), CRT monitors (OctaBDE and DecaBDE) and consumer equipment (DecaBDE), in particular CRT TVs (DecaBDE). To avoid a dissipation of hazardous substances into plastics and the environment, it is recommended that mixed plastics from WEEE are subject to a strict quality management.

  1. Solid-shape energy fuels from recyclable municipal solid waste and plastics

    Science.gov (United States)

    Gug, Jeongin

    Diversion of waste streams, such as plastics, wood and paper, from municipal landfills and extraction of useful materials from landfills is an area of increasing interest across the country, especially in densely populated areas. One promising technology for recycling MSW (municipal solid waste) is to burn the high energy content components in standard coal boilers. This research seeks to reform wastes into briquette that are compatible with typical coal combustion processes. In order to comply with the standards of coal-fired power plants, the feedstock must be mechanically robust, moisture resistance, and retain high fuel value. Household waste with high paper and fibers content was used as the base material for this study. It was combined with recyclable plastics such as PE, PP, PET and PS for enhanced binding and energy efficiency. Fuel pellets were processed using a compression molding technique. The resulting moisture absorption, proximate analysis from burning, and mechanical properties were investigated after sample production and then compared with reference data for commercial coals and biomass briquettes. The effects of moisture content, compression pressure and processing temperature were studied to identify the optimal processing conditions with water uptake tests for the durability of samples under humid conditions and burning tests to examine the composition of samples. Lastly, mechanical testing revealed the structural stability of solid fuels. The properties of fuel briquettes produced from waste and recycled plastics improved with higher processing temperature but without charring the material. Optimization of moisture content and removal of air bubbles increased the density, stability and mechanical strength. The sample composition was found to be more similar to biomass fuels than coals because the majority of the starting material was paper-based solid waste. According to the proximate analysis results, the waste fuels can be expected to have

  2. Study on the hydrocyclonic separation of waste plastics with different density.

    Science.gov (United States)

    Yuan, H; Fu, S; Tan, W; He, J; Wu, K

    2015-11-01

    The recycling of waste plastics is an important aspect in the recycling of solid waste. Based on the difference in density, PET and PVC particles was separated with help of the centrifugal sedimentation and shearing dispersion in a hydrocyclone. Through tests and CFD simulation, the relationship between the separating efficiency and pressure drop and split ratio has been investigated. Test results show that the Newton efficiency can reach above 80%, i.e. the purity of PVC could reach 93.2% while the purity of PET could reach 94.5%.

  3. Removal of brominated flame retardant from electrical and electronic waste plastic by solvothermal technique.

    Science.gov (United States)

    Zhang, Cong-Cong; Zhang, Fu-Shen

    2012-06-30

    Brominated flame retardants (BFRs) in electrical and electronic (E&E) waste plastic are toxic, bioaccumulative and recalcitrant. In the present study, tetrabromobisphenol A (TBBPA) contained in this type of plastic was tentatively subjected to solvothermal treatment so as to obtain bromine-free plastic. Methanol, ethanol and isopropanol were examined as solvents for solvothermal treatment and it was found that methanol was the optimal solvent for TBBPA removal. The optimum temperature, time and liquid to solid ratio for solvothermal treatment to remove TBBPA were 90°C, 2h and 15:1, respectively. After the treatment with various alcohol solvents, it was found that TBBPA was finally transferred into the solvents and bromine in the extract was debrominated catalyzed by metallic copper. Bisphenol A and cuprous bromide were the main products after debromination. The morphology and FTIR properties of the plastic were generally unchanged after the solvothermal treatment indicating that the structure of the plastic maintained after the process. This work provides a clean and applicable process for BFRs-containing plastic disposal.

  4. Effects of Waste Plastic Oil Blends on a Multi Cylinder Spark Ignition Engine

    Directory of Open Access Journals (Sweden)

    Vijaya Kumar Kareddula

    2017-01-01

    Full Text Available Existing fossil fuels are utilizing at their critical rate, leads to depletion of their reserves in a dramatic way. Generating alternative energy sources in a pragmatic way are necessitated, which demands the researchers to utilize the inherent energy of carbon based products as an energy source to the automobile sector. As a part of it, my research is focused on transforming and using the waste plastics as an alternative fuel in multi cylinder spark ignition engine. This paper aims to present the experimental investigations of performance and emission characteristics in an existing Maruti 800 petrol engine running with the blends of 5%, 10%, 15% and 20% of waste Plastic Pyrolysis Oil (PPO with gasoline. From the results, it is noticed that hydrocarbon emissions are substantially reduced and oxides of nitrogen emissions are increased and petrol engine can operate with PPO blends up to 20% without any engine modifications.

  5. Upgrading of recycled plastics obtained from flexible packaging waste by adding nanosilicates

    Science.gov (United States)

    Garofalo, E.; Claro, M.; Scarfato, P.; Di Maio, L.; Incarnato, L.

    2015-12-01

    Currently, the growing consumption of polymer products creates large quantities of waste materials resulting in public concern in the environment and people life. The efficient treatment of polymer wastes is still a difficult challenge and the recycling process represents the best way to manage them. Recently, many researchers have tried to develop nanotechnology for polymer recycling. The products prepared through the addition of nanoparticles to post-used plastics could offer the combination of improved properties, low weight, easy of processing and low cost which is not easily and concurrently found by other methods of plastic recycling. In this study materials, obtained by the separation and mechanical recycling of post-consumer packaging films of small size (organic modifier, were melt compounded with the recycled materials in a twin-screw extruder. The morphological, thermal, rheological and mechanical properties of the prepared nanocomposites were extensively discussed.

  6. WATER RESISTANCE OF WOOD - PLASTIC COMPOSITES MADE FROM WASTE MATERIALS RESULTED IN THE FURNITURE MANUFACTURING PROCESS

    OpenAIRE

    Camelia COŞEREANU; Dumitru LICA; Ioan CURTU; Mariana-Domnica STANCIU

    2014-01-01

    The purpose of this paper is to present innovative wood-plastic composites made from waste materials such as ABS (acrylonitrile butadiene styrene) and wood shavings resulted in the furniture manufacturing process. From previous investigations (with regard to physical integrity and compactness of the panels), only mixtures ranging from a ratio of 100% ABS: 0% shavings to 80% ABS: 20% shavings were selected for water resistance testing. Swelling in thickness and water absorption for...

  7. Polarity Determinants in Dendritic Spine Development and Plasticity.

    Science.gov (United States)

    Zhang, Huaye

    2016-01-01

    The asymmetric distribution of various proteins and RNAs is essential for all stages of animal development, and establishment and maintenance of this cellular polarity are regulated by a group of conserved polarity determinants. Studies over the last 10 years highlight important functions for polarity proteins, including apical-basal polarity and planar cell polarity regulators, in dendritic spine development and plasticity. Remarkably, many of the conserved polarity machineries function in similar manners in the context of spine development as they do in epithelial morphogenesis. Interestingly, some polarity proteins also utilize neuronal-specific mechanisms. Although many questions remain unanswered in our understanding of how polarity proteins regulate spine development and plasticity, current and future research will undoubtedly shed more light on how this conserved group of proteins orchestrates different pathways to shape the neuronal circuitry.

  8. Polarity Determinants in Dendritic Spine Development and Plasticity

    Directory of Open Access Journals (Sweden)

    Huaye Zhang

    2016-01-01

    Full Text Available The asymmetric distribution of various proteins and RNAs is essential for all stages of animal development, and establishment and maintenance of this cellular polarity are regulated by a group of conserved polarity determinants. Studies over the last 10 years highlight important functions for polarity proteins, including apical-basal polarity and planar cell polarity regulators, in dendritic spine development and plasticity. Remarkably, many of the conserved polarity machineries function in similar manners in the context of spine development as they do in epithelial morphogenesis. Interestingly, some polarity proteins also utilize neuronal-specific mechanisms. Although many questions remain unanswered in our understanding of how polarity proteins regulate spine development and plasticity, current and future research will undoubtedly shed more light on how this conserved group of proteins orchestrates different pathways to shape the neuronal circuitry.

  9. Ex-situ bioremediation of Brazilian soil contaminated with plasticizers process wastes

    Directory of Open Access Journals (Sweden)

    I. D. Ferreira

    2012-03-01

    Full Text Available The aim of this research was to evaluate the bioremediation of a soil contaminated with wastes from a plasticizers industry, located in São Paulo, Brazil. A 100-kg soil sample containing alcohols, adipates and phthalates was treated in an aerobic slurry-phase reactor using indigenous and acclimated microorganisms from the sludge of a wastewater treatment plant of the plasticizers industry (11gVSS kg-1 dry soil, during 120 days. The soil pH and temperature were not corrected during bioremediation; soil humidity was corrected weekly to maintain 40%. The biodegradation of the pollutants followed first-order kinetics; the removal efficiencies were above 61% and, among the analyzed plasticizers, adipate was removed to below the detection limit. Biological molecular analysis during bioremediation revealed a significant change in the dominant populations initially present in the reactor.

  10. A new classification scheme of plastic wastes based upon recycling labels

    Energy Technology Data Exchange (ETDEWEB)

    Özkan, Kemal, E-mail: kozkan@ogu.edu.tr [Computer Engineering Dept., Eskişehir Osmangazi University, 26480 Eskişehir (Turkey); Ergin, Semih, E-mail: sergin@ogu.edu.tr [Electrical Electronics Engineering Dept., Eskişehir Osmangazi University, 26480 Eskişehir (Turkey); Işık, Şahin, E-mail: sahini@ogu.edu.tr [Computer Engineering Dept., Eskişehir Osmangazi University, 26480 Eskişehir (Turkey); Işıklı, İdil, E-mail: idil.isikli@bilecik.edu.tr [Electrical Electronics Engineering Dept., Bilecik University, 11210 Bilecik (Turkey)

    2015-01-15

    Highlights: • PET, HPDE or PP types of plastics are considered. • An automated classification of plastic bottles based on the feature extraction and classification methods is performed. • The decision mechanism consists of PCA, Kernel PCA, FLDA, SVD and Laplacian Eigenmaps methods. • SVM is selected to achieve the classification task and majority voting technique is used. - Abstract: Since recycling of materials is widely assumed to be environmentally and economically beneficial, reliable sorting and processing of waste packaging materials such as plastics is very important for recycling with high efficiency. An automated system that can quickly categorize these materials is certainly needed for obtaining maximum classification while maintaining high throughput. In this paper, first of all, the photographs of the plastic bottles have been taken and several preprocessing steps were carried out. The first preprocessing step is to extract the plastic area of a bottle from the background. Then, the morphological image operations are implemented. These operations are edge detection, noise removal, hole removing, image enhancement, and image segmentation. These morphological operations can be generally defined in terms of the combinations of erosion and dilation. The effect of bottle color as well as label are eliminated using these operations. Secondly, the pixel-wise intensity values of the plastic bottle images have been used together with the most popular subspace and statistical feature extraction methods to construct the feature vectors in this study. Only three types of plastics are considered due to higher existence ratio of them than the other plastic types in the world. The decision mechanism consists of five different feature extraction methods including as Principal Component Analysis (PCA), Kernel PCA (KPCA), Fisher’s Linear Discriminant Analysis (FLDA), Singular Value Decomposition (SVD) and Laplacian Eigenmaps (LEMAP) and uses a simple

  11. Plastic Jellyfish.

    Science.gov (United States)

    Moseley, Christine

    2000-01-01

    Presents an environmental science activity designed to enhance students' awareness of the hazards of plastic waste for wildlife in aquatic environments. Discusses how students can take steps to reduce the effects of plastic waste. (WRM)

  12. An experimental study on thermo-catalytic pyrolysis of plastic waste using a continuous pyrolyser.

    Science.gov (United States)

    Auxilio, Anthony R; Choo, Wei-Lit; Kohli, Isha; Chakravartula Srivatsa, Srikanth; Bhattacharya, Sankar

    2017-09-01

    A bench scale, two-stage, thermo-catalytic reactor equipped with a continuous feeding system was used to pyrolyse pure and waste plastics. Experiments using five zeolitic and clay-based catalysts of different forms (pellet and powders) and different plastic feedstocks - virgin HDPE, HDPE w1aste and mixed plastic waste (MPW) were compared to the control experiments - pyrolysis without catalyst. Results indicated that the two pelletized catalysts were the most promising for the conditions employed. Of these two, one with higher acidity and surface area was highly selective for the gasoline fraction (C5-C11) giving 80% from the total medium distillate conversion using virgin HDPE as feedstock. It also produced the least amount of olefins (17% for virgin HDPE, 4% for HDPE waste and 2% for MPW) and coke (pelletized catalyst exhibited high selectivity for the diesel fraction (C12-C25) giving 63% from the total medium distillate conversion using virgin HDPE as feedstock. The amount of coke deposited on the catalyst surface depended mainly on the mesopore volume, with less coke deposited as the mesopore volume increased. The variation in catalyst selectivity with acidity strength due to Lewis sites on the catalyst surface controls selectivity towards carbon chain length. Copyright © 2017 Elsevier Ltd. All rights reserved.

  13. Recycling of polyethylene terephthalate (PET plastic bottle wastes in bituminous asphaltic concrete

    Directory of Open Access Journals (Sweden)

    Adebayo Olatunbosun Sojobi

    2016-12-01

    Full Text Available This research sheds light on the concept of eco-friendly road construction which comprises eco-design, eco-extraction, eco-manufacturing, eco-construction, eco-rehabilitation, eco-maintenance, eco-demolition, and socioeconomic empowerment. It also revealed the challenges being faced in its adoption and the benefits derivable from its application. Furthermore, the effects of recycling PET plastic bottle wastes produced in North Central Nigeria in bituminous asphaltic concrete (BAC used in flexible pavement construction were also evaluated. The mix design consists of 60/70 penetration-grade asphaltic concrete (5%, 68% coarse aggregate, 6% fine aggregate, and 21% filler using the dry process at 170°C. The optimum bitumen content (OBC for conventional BAC was obtained as 4% by weight of total aggregates and filler. Polymer-coated aggregate (PCA-modified BAC seems preferable because it has the potential to utilize more plastic wastes with a higher optimum plastic content (OPC of 16.7% by weight of total aggregates and filler compared to that of 9% by weight of OBC achieved by PMB-BAC. For both PMB- and PCA-modified BAC, an increase in air void, void in mineral aggregate, and Marshall stability were observed. Eco-friendly road construction which recycles PET wastes should be encouraged by government considering its potential environmental and economic benefits.

  14. Synthesis of Petroleum-Based Fuel from Waste Plastics and Performance Analysis in a CI Engine

    Directory of Open Access Journals (Sweden)

    Christine Cleetus

    2013-01-01

    Full Text Available The present work involves the synthesis of a petroleum-based fuel by the catalytic pyrolysis of waste plastics. Catalytic pyrolysis involves the degradation of the polymeric materials by heating them in the absence of oxygen and in the presence of a catalyst. In the present study different oil samples are produced using different catalysts under different reaction conditions from waste plastics. The synthesized oil samples are subjected to a parametric study based on the oil yield, selectivity of the oil, fuel properties, and reaction temperature. Depending on the results from the above study, an optimization of the catalyst and reaction conditions was done. Gas chromatography-mass spectrometry of the selected optimized sample was done to find out its chemical composition. Finally, performance analysis of the selected oil sample was carried out on a compression ignition (CI engine. Polythene bags are selected as the source of waste plastics. The catalysts used for the study include silica, alumina, Y zeolite, barium carbonate, zeolite, and their combinations. The pyrolysis reaction was carried at polymer to catalyst ratio of 10 : 1. The reaction temperature ranges between 400°C and 550°C. The inert atmosphere for the pyrolysis was provided by using nitrogen as a carrier gas.

  15. Pyrolysis of municipal plastic wastes: Influence of raw material composition.

    Science.gov (United States)

    López, A; de Marco, I; Caballero, B M; Laresgoiti, M F; Adrados, A

    2010-04-01

    The objective of this work is the study of pyrolysis as a feedstock recycling process, for valorizing the rejected streams that come from industrial plants, where packing and packaging wastes are classified and separated for their subsequent mechanical recycling. Four real samples collected from an industrial plant at four different times of the year, have been pyrolysed under nitrogen in a 3.5dm(3) autoclave at 500 degrees C for 30min. Pyrolysis liquids are a complex mixture of organic compounds containing valuable chemicals as styrene, ethyl-benzene, toluene, etc. Pyrolysis solids are composed of the inorganic material contained in the raw materials, as well as of some char formed in the pyrolysis process, and pyrolysis gases are mainly composed of hydrocarbons together with some CO and CO(2), and have very high gross calorific values (GCV). It has been proved by the authors that the composition of the raw material (paper, film, and metals contents) plays a significant role in the characteristics of pyrolysis products. High paper content yields water in the pyrolysis liquids, and CO and CO(2) in the gases, high PE film content gives rise to high viscosity liquids, and high metals content yields more aromatics in the liquid products, which may be attributed to the metals catalytic effect.

  16. Application of dissolved air flotation on separation of waste plastics ABS and PS.

    Science.gov (United States)

    Wang, Hui; Chen, Xiao-Lei; Bai, Yang; Guo, Chao; Zhang, Li

    2012-07-01

    The aim of this research was to separate waste plastics acrylonitrile butadiene styrene (ABS) and polystyrene (PS) by dissolved air flotation in a self-designed dissolved air flotation apparatus. The effects of wetting agents, frother, conditioning time and flotation time on flotation behavior of waste plastics ABS (w-ABS) and PS (w-PS) were investigated and the optimized separation conditions were obtained. The results showed that when using 25 mgL(-1) tannic acid, 5 mgL(-1) terpineol, 15 min conditioning time and 15 min flotation time, mixtures of w-ABS and w-PS were separated successfully by dissolved air flotation in two stages, the results revealed that the purity and recovery rate of w-PS in the floated products were 90.12% and 97.45%, respectively, and the purity and recovery rate of w-ABS in the depressed products were 97.24% and 89.38%, respectively. Based on the studies of wetting mechanism of plastic flotation, it is found that the electrostatic force and hydrophobic attraction cannot be the main factor of the interaction between wetting agent molecules and plastic particles, which can be completed through water molecules as a mesophase, and a hydrogen bonding adsorption model with hydration shell as a mesophase was proposed.

  17. Recycling of mixed plastic waste from electrical and electronic equipment. Added value by compatibilization.

    Science.gov (United States)

    Vazquez, Yamila V; Barbosa, Silvia E

    2016-07-01

    Plastic waste from electrical and electronic equipment (WEEE) grows up exponentially fast in the last two decades. Either consumption increase of technological products, like cellphones or computers, or the short lifetime of this products contributes to this rise generating an accumulation of specific plastic materials such ABS (Acrylonitrile-Butadiene-Styrene), HIPS (High impact Polystyrene), PC (Polycarbonate), among others. All of they can be recycled by themselves. However, to separate them by type is neither easy nor economically viable, then an alternative is recycling them together as a blend. Taking into account that could be a deterioration in final properties, to enhance phase adhesion and add value to a new plastic WEEE blend a compatibilization is needed. In this work, a systematical study of different compatibilizers for blends of HIPS and ABS from WEEE was performed. A screening analysis was carried out by adding two different compatibilizer concentration (2wt% and 20wt%) on a HIPS/ABS physical blend 80/20 proportion from plastic e-waste. Three copolymers were selected as possible compatibilizers by their possible affinity with initial plastic WEEE. A complete characterization of each WEEE was performed and compatibilization efficiency was evaluated by comparing either mechanical or morphological blends aspects. Considering blends analyzed in this work, the best performance was achieved by using 2% of styrene-acrylonitrile rubber, obtaining a compatibilized blend with double ultimate strength and modulus respect to the physical blend, and also improve mechanical properties of initial WEEE plastics. The proposed way is a promise route to improve benefit of e-scrap with sustainable, low costs and easy handling process. Consequently, social recycling interest will be encouraged by both ecological and economical points of view.

  18. Application of biotests for the determination of soil ecotoxicity after exposure to biodegradable plastics

    OpenAIRE

    2016-01-01

    Biodegradable plastics are mostly applied in packaging materials (e.g. shopping bags), waste collection bags, catering products, and agricultural applications. In this last case, degradation takes place directly in soil where biodegradable plastic products are intentionally left after use (e.g. mulch films for weeds control). Due to the growing volumes of biodegradable polymers and plastics, interest in their environmental safety is increasing and more research is carried out. Some attempt ha...

  19. An Experimental Investigation on Utilization of Waste Plastic as a Modifier in Rigid Pavements for Improving Strength

    Directory of Open Access Journals (Sweden)

    M.Chandu

    2016-12-01

    Full Text Available The percent study investigates the effective use of waste plastic as a modifier for cement concrete roads. Civilization produces waste products disposals issue of the waste products is a challenge. Solid waste management is the thrust area. The various waste materials, plastic waste and principle solid waste are of great concern these leads to disposal crisis and environmental pollution. On the other side, road traffic is increasing. The load bearing capacity of the roads are to be increased. Our present work is helping to take care of both these aspects. Plastic waste consists of carry bags cups and disposals. Plastic waste which is cleaned is cut into a size such that it passes through 2.3mm sieve using shredding machine. The aggregates mix is heated and the plastic is coated over aggregates and this coated stones can be used for road constructing. By this process a road of 1km length 3.375m width of single lane can consumes 10,00000 carry bags and road strength is increased and found no pot holes. Commonly soil, aggregates, sand, cement can be used in road construction. Natural materials being exhaustible in nature, its quantity is declining gradually. If our material can be utilized in highway construction, the pollution and disposal problems may be partly reduced. The use of the innovative technology will not only strengthen the road construction but also increase the road life as well as will help to improve the environment. In my research work I have done a thorough study on the methodology of using plastic waste coat over aggregates and presented various tests performed on aggregates.

  20. Composition of plastics from waste electrical and electronic equipment (WEEE) by direct sampling.

    Science.gov (United States)

    Martinho, Graça; Pires, Ana; Saraiva, Luanha; Ribeiro, Rita

    2012-06-01

    This paper describes a direct analysis study carried out in a recycling unit for waste electrical and electronic equipment (WEEE) in Portugal to characterize the plastic constituents of WEEE. Approximately 3400 items, including cooling appliances, small WEEE, printers, copying equipment, central processing units, cathode ray tube (CRT) monitors and CRT televisions were characterized, with the analysis finding around 6000 kg of plastics with several polymer types. The most common polymers are polystyrene, acrylonitrile-butadiene-styrene, polycarbonate blends, high-impact polystyrene and polypropylene. Additives to darken color are common contaminants in these plastics when used in CRT televisions and small WEEE. These additives can make plastic identification difficult, along with missing polymer identification and flame retardant identification marks. These drawbacks contribute to the inefficiency of manual dismantling of WEEE, which is the typical recycling process in Portugal. The information found here can be used to set a baseline for the plastics recycling industry and provide information for ecodesign in electrical and electronic equipment production.

  1. 40 CFR 265.1084 - Waste determination procedures.

    Science.gov (United States)

    2010-07-01

    ... the exit concentration limit (Ct) for a treated hazardous waste. (i) The point of waste origination... limit (Ct) shall be 500 ppmw. (iii) If more than one hazardous waste stream is identified in paragraph... this section. The exit concentration limit (Ct) shall be calculated by using the results determined...

  2. Application of electrostatic separation to the recycling of plastic wastes: separation of PVC, PET, and ABS.

    Science.gov (United States)

    Park, Chul-Hyun; Jeon, Ho-Seok; Yu, Hyo-Shin; Han, Oh-Hyung; Park, Jai-Koo

    2008-01-01

    Plastics are widely used in everyday life as a useful material, and thus their consumption is growing at a rate of about 5% per year in Korea. However, the constant generation of plastic wastes and their disposal generates environmental problems along with economic loss. In particular, mixed waste plastics are difficult to recycle because of their inferior characteristics. A laboratory-scale triboelectrostatic separator unit has been designed and assembled for this study. On the basis of the control of electrostatic charge, the separation of three kinds of mixed plastics, polyvinyl chloride (PVC), poly(ethylene terephthalate) (PET), and acrylonitrile-butadiene-styrene (ABS), in a range of similar gravities has been performed through a two-stage separation process. Polypropylene (PP) and high-impact polystyrene (HIPS) were found to be the most effective materials for a tribo-charger in the separation of PVC, PET, and ABS. The charge-to-mass ratio (nC/g) of plastics increased with increasing air velocity in the tribo charger. In the first stage, using the PP cyclone charger, the separation efficiency of particles considerably depended on the air velocity (10 m/s), the relative humidity ( 20 kV), and the splitter position (+2 cm from the center) in the triboelelctrostatic separator unit. At this time, a PVC grade of 99.40% and a recovery of 98.10% have successfully been achieved. In the second stage, using the HIPS cyclone charger, a PET grade of 97.80% and a recovery of 95.12% could be obtained under conditions of 10 m/s, over 25 kV, a central splitter position, and less than 40% relative humidity. In order to obtain 99.9% PVC grade and 99.3% PET grade, their recoveries should be sacrificed by 20.9% and 27%, respectively, with moving the splitter from the center to a (+)6 cm position.

  3. A new classification scheme of plastic wastes based upon recycling labels.

    Science.gov (United States)

    Özkan, Kemal; Ergin, Semih; Işık, Şahin; Işıklı, Idil

    2015-01-01

    Since recycling of materials is widely assumed to be environmentally and economically beneficial, reliable sorting and processing of waste packaging materials such as plastics is very important for recycling with high efficiency. An automated system that can quickly categorize these materials is certainly needed for obtaining maximum classification while maintaining high throughput. In this paper, first of all, the photographs of the plastic bottles have been taken and several preprocessing steps were carried out. The first preprocessing step is to extract the plastic area of a bottle from the background. Then, the morphological image operations are implemented. These operations are edge detection, noise removal, hole removing, image enhancement, and image segmentation. These morphological operations can be generally defined in terms of the combinations of erosion and dilation. The effect of bottle color as well as label are eliminated using these operations. Secondly, the pixel-wise intensity values of the plastic bottle images have been used together with the most popular subspace and statistical feature extraction methods to construct the feature vectors in this study. Only three types of plastics are considered due to higher existence ratio of them than the other plastic types in the world. The decision mechanism consists of five different feature extraction methods including as Principal Component Analysis (PCA), Kernel PCA (KPCA), Fisher's Linear Discriminant Analysis (FLDA), Singular Value Decomposition (SVD) and Laplacian Eigenmaps (LEMAP) and uses a simple experimental setup with a camera and homogenous backlighting. Due to the giving global solution for a classification problem, Support Vector Machine (SVM) is selected to achieve the classification task and majority voting technique is used as the decision mechanism. This technique equally weights each classification result and assigns the given plastic object to the class that the most classification

  4. Finding an Optimum Period of Oxidative Heat Treatment on SS 316 Catalyst for Nanocarbon Production from LDPE Plastic Waste

    Directory of Open Access Journals (Sweden)

    Praswasti P.D.K. Wulan

    2017-04-01

    Full Text Available Plastic waste accumulation has become a major health and environmental problems in many parts of the world. Many efforts have been taken to reduce the accumulation, one of which is to convert it into a more useful products, such as CNT. CNT have been used for several products to enhance its properties. In this work, Low Density Polyethylene (LDPE plastic waste was used as a feed to produce CNT with the help of wired mesh stainless steel type 316 serving as the catalyst. The stainless steel was pretreated by applying heat under oxidative environment at 800oC. The time of the pretreatment was varied from 0, 1, 5, 10, and 20 minutes to determine the relationship between the period of the pretreatment and the produced CNT quality. The collected nanocarbons were characterized by using XRD, SEM-EDX, TEM, and TGA. It was discovered that CNT was formed from the pretreated catalyst. The best result was obtained from the 10 minutes pretreatment shown by formation of buckling and continuous growth CNT having an evenly spread carbon with a mean CNT diameter of 7.70 nm, carbon percentage up to 93.3%, and oxidation temperature up to 530oC.

  5. Engine performance and emission characteristics of plastic oil produced from waste polyethylene and its blends with diesel fuel

    Energy Technology Data Exchange (ETDEWEB)

    Yin, Sudong; Tan, Zhongchao [Department of Mechanical and Mechatronics Engineering, University of Waterloo (Canada)], Email: tanz@uwaterloo.ca

    2011-07-01

    This paper describes an experiment to determine the possibility of transforming waste plastics into a potential source of diesel fuel. Experiments were done on the use of various blends of plastic oil produced from waste polyethylene (WPE) with diesel fuel (D) at different volumetric ratios and the results were reviewed. WPE was thermally degraded with catalysis of sodium aluminum silicate at optimum conditions (414-480 degree celsius range and 1 h reaction time) and the collected oil was fractionated at various temperatures. The properties of the fuel blends at different volumetric ratios were measured in this study. It was shown that these blends can be used as fuel in compression ignition engines without any modification. With respect to engine performance and exhaust emission, it was found that using a 5% WPE-D (WPE5) blend instead of diesel fuel reduced carbon monoxide (CO) emission. However, the results of experiment showed that carbon dioxide (CO2) emission and oxides of nitrogen (NOx) emission rose.

  6. Determination of Metal Ion Concentrations in Components of Household Solid Waste in the Akwapim South Municipality of Ghana

    Directory of Open Access Journals (Sweden)

    M. Ackah

    2011-08-01

    Full Text Available The potential of household solid waste to supply micro-nutrients is studied. The study aimed at finding the levels of metal ion concentrations in domestic refuse typically the organic, paper and plastic waste stream components which constituted the highest waste stream fractions generated by residents in the Nsawam- Adoadjiri townships. INAA was used to determine metal ions concentrations in household solid organic, paper and plastic components of wastes generated by sampled households of Nsawam and Adoagyiri townships of the Akwapim South Municipality of Ghana. The analysis covered (Ca, K, Mg, Na, Cu, Mn, Al, Cl, and V. Standard reference materials were also analysed in the same manner as the waste samples to ensure good quality control/quality assurance procedures. Higher mean concentrations of 5.59 μg/g and 13.27 mg/g were recorded for Mn and Cl, respectively in organic waste stream component as compared to 1.13 μg/g and 0.19 mg/g in paper/cardboard waste stream and 2.67 μg/g and 13.27 mg/g in rubber/plastic waste stream components respectively. These values are comparable to literature values.

  7. The potential environmental gains from recycling waste plastics: simulation of transferring recycling and recovery technologies to Shenyang, China.

    Science.gov (United States)

    Chen, Xudong; Xi, Fengming; Geng, Yong; Fujita, Tsuyoshi

    2011-01-01

    With the increasing attention on developing a low-carbon economy, it is necessary to seek appropriate ways on reducing greenhouse gas (GHG) emissions through innovative municipal solid waste management (MSWM), such as urban symbiosis. However, quantitative assessments on the environmental benefits of urban symbiosis, especially in developing countries, are limited because only a limited number of planned synergistic activities have been successful and it is difficult to acquire detailed inventory data from private companies. This paper modifies and applies a two-step simulation system and used it to assess the potential environmental benefits, including the reduction of GHG emissions and saving of fossil fuels, by employing various Japanese plastics recycling/energy-recovery technologies in Shenyang, China. The results showed that among various recycling/energy-recovery technologies, the mechanical waste plastics recycling technology, which produces concrete formwork boards (NF boards), has the greatest potential in terms of reducing GHG emissions (1.66 kg CO(2)e/kg plastics), whereas the technology for the production of refuse plastic fuel (RPF) has the greatest potential on saving fossil fuel consumption (0.77 kg ce/kg-plastics). Additional benefits can be gained by applying combined technologies that cascade the utilization of waste plastics. Moreover, the development of clean energy in conjunction with the promotion of new waste plastics recycling programs could contribute to additional reductions in GHG emissions and fossil fuel consumption.

  8. Energy Payback Time of a Solar Photovoltaic Powered Waste Plastic Recyclebot System

    Directory of Open Access Journals (Sweden)

    Shan Zhong

    2017-06-01

    Full Text Available The growth of both plastic consumption and prosumer 3-D printing are driving an interest in producing 3-D printer filaments from waste plastic. This study quantifies the embodied energy of a vertical DC solar photovoltaic (PV powered recyclebot based on life cycle energy analysis and compares it to horizontal AC recyclebots, conventional recycling, and the production of a virgin 3-D printer filament. The energy payback time (EPBT is calculated using the embodied energy of the materials making up the recyclebot itself and is found to be about five days for the extrusion of a poly lactic acid (PLA filament or 2.5 days for the extrusion of an acrylonitrile butadiene styrene (ABS filament. A mono-crystalline silicon solar PV system is about 2.6 years alone. However, this can be reduced by over 96% if the solar PV system powers the recyclebot to produce a PLA filament from waste plastic (EPBT is only 0.10 year or about a month. Likewise, if an ABS filament is produced from a recyclebot powered by the solar PV system, the energy saved is 90.6–99.9 MJ/kg and 26.33–29.43 kg of the ABS filament needs to be produced in about half a month for the system to pay for itself. The results clearly show that the solar PV system powered recyclebot is already an excellent way to save energy for sustainable development.

  9. Nanobarium Titanate As Supplement To Accelerate Plastic Waste Biodegradation By Indigenous Bacterial Consortia

    Science.gov (United States)

    Kapri, Anil; Zaidi, M. G. H.; Goel, Reeta

    2009-06-01

    Plastic waste biodegradation studies have seen several developmental phases from the discovery of potential microbial cultures, inclusion of photo-oxidizable additives into the polymer chain, to the creation of starch-embedded biodegradable plastics. The present study deals with the supplementation of nanobarium titanate (NBT) in the minimal broth in order to alter the growth-profiles of the Low-density polyethylene (LDPE) degrading consortia. The pro-bacterial influence of the nanoparticles could be seen by substantial changes such as shortening of the lag phase and elongation of the exponential as well as stationary growth phases, respectively, which eventually increase the biodegradation efficiency. In-vitro biodegradation studies revealed better dissolution of LDPE in the presence of NBT as compared to control. Significant shifting in λ-max values was observed in the treated samples through UV-Vis spectroscopy, while Fourier transform infrared spectroscopy (FTIR) and simultaneous thermogravimetric-differential thermogravimetry-differential thermal analysis (TG-DTG-DTA) further confirmed the breakage and formation of bonds in the polymer backbone. Therefore, this study suggests the implementation of NBT as nutritional additive for plastic waste management through bacterial growth acceleration.

  10. Polystyrene (PS waste plastic conversion into aviation/kerosene category of fuel by using fractional column distillation process

    Directory of Open Access Journals (Sweden)

    Moinuddin Sarker, Mohammad Mamunor Rashid, Muhammad Sadikur Rahman, Mohammed Molla

    2012-01-01

    Full Text Available Environmental degradation and depleting fuel reserves are matters of great concern around the global. Solid waste plastic is currently receiving renewed interest for fuel generation. Waste plastic to fuel is suitable for compression ignition engines and more attention is focused in the world because of its potential to generate large-scale employment and relatively low environmental degradation. A post-commercial PS polymer waste was thermal degradation and fractional distillation without catalysts using a steel reactor operating thermally at ambient pressure under fume hood without vacuum system. Two types of temperature profile was used for this experiment such as PS waste plastic liquefaction purposed temperature used 100-400 ºC and fractional column distillation temperature was used 180-305 ºC for collection kerosene or aviation grade fuel. Produced fuel was analyzed by using gas chromatography and mass spectrometer and fuel hydrocarbon range showed into GC/MS analysis is C6 to C16.

  11. Characterisation and materials flow management for waste electrical and electronic equipment plastics from German dismantling centres.

    Science.gov (United States)

    Arends, Dagmar; Schlummer, Martin; Mäurer, Andreas; Markowski, Jens; Wagenknecht, Udo

    2015-09-01

    Waste electrical and electronic equipment is a complex waste stream and treatment options that work for one waste category or product may not be appropriate for others. A comprehensive case study has been performed for plastic-rich fractions that are treated in German dismantling centres. Plastics from TVs, monitors and printers and small household appliances have been characterised extensively. Based on the characterisation results, state-of-the-art treatment technologies have been combined to design an optimised recycling and upgrade process for each input fraction. High-impact polystyrene from TV casings that complies with the European directive on the restriction of hazardous substances (RoHS) was produced by applying continuous density separation with yields of about 60%. Valuable acrylonitrile butadiene styrene/polycarbonate can be extracted from monitor and printer casings by near-infrared-based sorting. Polyolefins and/or a halogen-free fraction of mixed styrenics can be sorted out by density separation from monitors and printers and small household appliances. Emerging separation technologies are discussed to improve recycling results. © The Author(s) 2015.

  12. A rating system for determination of hazardous wastes.

    Science.gov (United States)

    Talinli, Ilhan; Yamantürk, Rana; Aydin, Egemen; Başakçilardan-Kabakçi, Sibel

    2005-11-11

    Although hazardous waste lists and their classification methodologies are nearly the same in most of the countries, there are some gaps and subjectiveness in determining the waste as hazardous waste. A rating system for the determination of waste as a hazardous waste is presented in this study which aims to overcome the problems resulted from the existing methodologies. Overall rating value (ORV) calculates and quantifies the waste as regular, non-regular or hazardous waste in an "hourglass" scale. "ORV" as a cumulative-linear formulation in proposed model consists of components such as ecological effects of the waste (Ee) in terms of four main hazard criteria: ignitability, reactivity, corrosivity and toxicity; combined potential risk (CPR) including carcinogenic effect, toxic, infectious and persistence characteristics; existing lists and their methodology (L) and decision factor (D) to separate regular and non-regular waste. Physical form (f) and quantity (Q) of the waste are considered as factors of these components. Seventeen waste samples from different sources are evaluated to demonstrate the simulation of the proposed model by using "hourglass" scale. The major benefit of the presented rating system is to ease the works of decision makers in managing the wastes.

  13. Key Determinants of Waste Separation Intention among Students on Campus

    Directory of Open Access Journals (Sweden)

    Ayob Siti Fadzilah

    2016-01-01

    Full Text Available This study aims to identify the key determinants of waste separation intention among the students in Universiti Teknologi Malaysia (UTM. As reported in World Bank Report, generation of global municipal solid waste are approximately 1.3 billion tonnes per year, and it will increase approximately 2.2 billion tonnes per year by 2025. Similar trend in Malaysia which approximately eight million tonnes of municipal solid waste is produced daily. Upward trend of the solid waste generated is contributed by various forces including growth, increase of population, residents attitude and rapid urbanisation in the country. Considering the negative impacts from increase of waste generated in the country such as environmental degradation, separate the waste at its source can increase recycling rate and hence reduce waste generation. In the 11th Malaysia Plan, the government has urged the nation to actively practice waste separation. Understanding the determinants influencing waste separation behaviour can lead to effective waste reduction among the targeted group. This study adopted the Theory of Planned Behaviour as the fundamental framework. The key determinants of waste separation behaviour are attitude, subjectives norm, and perceived behavioural control. An elicitation survey has been conducted to explore the students’s beliefs relative to the waste separation behaviour. The empirical data collected were analysed using structural equation modelling (SEM assisted by SmartPLS software. The result shows that only determinants are significant towards intention which are attitude and Perceived Behavioural Control while Subjective Norm is not. The results of the study is significance to the organisation as identification of the determinants that influence waste separation intention contributes to a more focused waste separation programme that allign to Malaysia’s objective towards a sustainable developing country.

  14. Mixed plastics recycling technology

    CERN Document Server

    Hegberg, Bruce

    1995-01-01

    Presents an overview of mixed plastics recycling technology. In addition, it characterizes mixed plastics wastes and describes collection methods, costs, and markets for reprocessed plastics products.

  15. Separation of plastic waste via the hydraulic separator Multidune under different geometric configurations.

    Science.gov (United States)

    La Marca, Floriana; Moroni, Monica; Cherubini, Lorenzo; Lupo, Emanuela; Cenedese, Antonio

    2012-07-01

    The recovery of high-quality plastic materials is becoming an increasingly challenging issue for the recycling sector. Technologies for plastic recycling have to guarantee high-quality secondary raw material, complying with specific standards, for use in industrial applications. The variability in waste plastics does not always correspond to evident differences in physical characteristics, making traditional methodologies ineffective for plastic separation. The Multidune separator is a hydraulic channel allowing the sorting of solid particles on the basis of differential transport mechanisms by generating particular fluid dynamic conditions due to its geometric configuration and operational settings. In this paper, the fluid dynamic conditions were investigated by an image analysis technique, allowing the reconstruction of velocity fields generated inside the Multidune, considering two different geometric configurations of the device, Configuration A and Configuration B. Furthermore, tests on mono- and bi-material samples were completed with varying operational conditions under both configurations. In both series of experiments, the bi-material samples were composed of differing proportions (85% vs. 15%) to simulate real conditions in an industrial plant for the purifying of a useful fraction from a contaminating fraction. The separation results were evaluated in terms of grade and recovery of the useful fraction.

  16. Temperature and time influence on the waste plastics pyrolysis in the fixed bed reactor

    Directory of Open Access Journals (Sweden)

    Papuga Saša V.

    2016-01-01

    Full Text Available Pyrolysis as a technique of chemical recycling of plastic materials is causing an increasing level of interest as an environmentally and economically acceptable option for the processing of waste materials. Studies of these processes are carried out under different experimental conditions, in different types of reactors and with different raw materials, which makes the comparison of different processes and the direct application of process parameters quite complex. This paper presents the results of investigation of the influence of temperature in the range of 450°C to 525°C, on the yield of the process of pyrolysis of waste plastics mixture, composed of 45% polypropylene, 35% low density polyethylene and 25% high density polyethylene. Also, this paper presents results of the investigation of the effect of the reaction, atintervals of 30-90 [min], on the yield of pyrolysis of the mentioned waste plastics mixture. Research was conducted in a fixed bed pilot reactor, which was developed for this purpose. The results of the research show that at a temperature of 500°C, complete conversion of raw materials was achieved, for a period of 45 [min], with a maximum yield of the pyrolysis oil of 32.80%, yield of the gaseous products of 65.75% and the solid remains of 1.46%. Afurther increase of temperature increases the yield of gaseous products, at the expense of reducing the yield of pyrolysis oil. Obtained pyrolysis oil has a high calorific value of 45.96 [MJ/kg], and in this regard has potential applications as an alternative fuel.

  17. Phase Stability Determinations of DWPF Waste Glasses

    Energy Technology Data Exchange (ETDEWEB)

    Marra, S.L.

    1999-10-22

    Liquid high-level nuclear waste will be immobilized at the Savannah River Site (SRS) by vitrification in borosilicate glass. To fulfill this requirement, glass samples were heat treated at various times and temperatures. These results will provide guidance to the repository program about conditions to be avoided during shipping, handling and storage of DWPF canistered waste forms.

  18. MWCNTs synthesized from waste polypropylene plastics and its application in super-capacitors

    Science.gov (United States)

    Mishra, Neeraj; Shinde, Sachin; Vishwakarma, Ritesh; Kadam, Siddhi; Sharon, Madhuri; Sharon, Maheshwar

    2013-06-01

    The Multiwall Carbon Nanotubes (MWCNTs) were synthesized at 800 °C by single stage chemical vapor deposition (CVD) from the carbonaceous source of waste polypropylene plastic (WPP) in the presence of a Ni catalyst. The fabrication of capacitor cell is very simple and does not require any binders. The electrochemical performances of the carbon nanotubes electrode were investigated by use of the cyclic voltammetry and galvanostatic charge/discharge for its application in super capacitors. The specific capacitance of 59 F/g of the electrode was achieved with scan rate of 5 mV/s in the solution of 1N KOH.

  19. Reuse and Recovery of Waste Plastic%废弃塑料的回收利用

    Institute of Scientific and Technical Information of China (English)

    赖寒

    2012-01-01

    The present situation of the reuse and recovery of waste plastics were reviewed, including the reuse and recovery of waste PP, PE, PVC, PS and PET. It is in order to realize the protection of human health and reduce the pollution of the environment and resources recycling purpose.%论述了目前废弃塑料回收利用方面的发展现状,介绍了聚丙烯、聚乙烯、聚对苯二甲酸乙二醇酯、聚氯乙烯、聚苯乙烯等废弃塑料的回收利用方法,以实现保护人类健康和减少环境污染和资源循环使用的目的。

  20. Exposure to airborne fungi during sorting of recyclable plastics in waste treatment facilities

    Directory of Open Access Journals (Sweden)

    Kristýna Černá

    2017-02-01

    Full Text Available Background: In working environment of waste treatment facilities, employees are exposed to high concentrations of airborne microorganisms. Fungi constitute an essential part of them. This study aims at evaluating the diurnal variation in concentrations and species composition of the fungal contamination in 2 plastic waste sorting facilities in different seasons. Material and Methods: Air samples from the 2 sorting facilities were collected through the membrane filters method on 4 different types of cultivation media. Isolated fungi were classified to genera or species by using a light microscopy. Results: Overall, the highest concentrations of airborne fungi were recorded in summer (9.1×103–9.0×105 colony-forming units (CFU/m3, while the lowest ones in winter (2.7×103–2.9×105 CFU/m3. The concentration increased from the beginning of the work shift and reached a plateau after 6–7 h of the sorting. The most frequently isolated airborne fungi were those of the genera Penicillium and Aspergillus. The turnover of fungal species between seasons was relatively high as well as changes in the number of detected species, but potentially toxigenic and allergenic fungi were detected in both facilities during all seasons. Conclusions: Generally, high concentrations of airborne fungi were detected in the working environment of plastic waste sorting facilities, which raises the question of health risk taken by the employees. Based on our results, the use of protective equipment by employees is recommended and preventive measures should be introduced into the working environment of waste sorting facilities to reduce health risk for employees. Med Pr 2017;68(1:1–9

  1. Exposure to airborne fungi during sorting of recyclable plastics in waste treatment facilities.

    Science.gov (United States)

    Černá, Kristýna; Wittlingerová, Zdeňka; Zimová, Magdaléna; Janovský, Zdeněk

    2017-02-28

    In working environment of waste treatment facilities, employees are exposed to high concentrations of airborne microorganisms. Fungi constitute an essential part of them. This study aims at evaluating the diurnal variation in concentrations and species composition of the fungal contamination in 2 plastic waste sorting facilities in different seasons. Air samples from the 2 sorting facilities were collected through the membrane filters method on 4 different types of cultivation media. Isolated fungi were classified to genera or species by using a light microscopy. Overall, the highest concentrations of airborne fungi were recorded in summer (9.1×103-9.0×105 colony-forming units (CFU)/m3), while the lowest ones in winter (2.7×103-2.9×105 CFU/m3). The concentration increased from the beginning of the work shift and reached a plateau after 6-7 h of the sorting. The most frequently isolated airborne fungi were those of the genera Penicillium and Aspergillus. The turnover of fungal species between seasons was relatively high as well as changes in the number of detected species, but potentially toxigenic and allergenic fungi were detected in both facilities during all seasons. Generally, high concentrations of airborne fungi were detected in the working environment of plastic waste sorting facilities, which raises the question of health risk taken by the employees. Based on our results, the use of protective equipment by employees is recommended and preventive measures should be introduced into the working environment of waste sorting facilities to reduce health risk for employees. Med Pr 2017;68(1):1-9.

  2. Processing real-world waste plastics by pyrolysis-reforming for hydrogen and high-value carbon nanotubes.

    Science.gov (United States)

    Wu, Chunfei; Nahil, Mohamad A; Miskolczi, Norbert; Huang, Jun; Williams, Paul T

    2014-01-01

    Producing both hydrogen and high-value carbon nanotubes (CNTs) derived from waste plastics is reported here using a pyrolysis-reforming technology comprising a two-stage reaction system, in the presence of steam and a Ni-Mn-Al catalyst. The waste plastics consisted of plastics from a motor oil container (MOC), commercial waste high density polyethylene (HDPE) and regranulated HDPE waste containing polyvinyl chloride (PVC). The results show that hydrogen can be produced from the pyrolysis-reforming process, but also carbon nanotubes are formed on the catalyst. However, the content of 0.3 wt.% polyvinyl chloride in the waste HDPE (HDPE/PVC) has been shown to poison the catalyst and significantly reduce the quantity and purity of CNTs. The presence of sulfur has shown less influence on the production of CNTs in terms of quantity and CNT morphologies. Around 94.4 mmol H2 g(-1) plastic was obtained for the pyrolysis-reforming of HDPE waste in the presence of the Ni-Mn-Al catalyst and steam at a reforming temperature of 800 °C. The addition of steam in the process results in an increase of hydrogen production and reduction of carbon yield; in addition, the defects of CNTs, for example, edge dislocations were found to be increased with the introduction of steam (from Raman analysis).

  3. Characterization of Some Real Mixed Plastics from WEEE: A Focus on Chlorine and Bromine Determination by Different Analytical Methods

    Directory of Open Access Journals (Sweden)

    Beatrice Beccagutti

    2016-10-01

    Full Text Available Bromine and chlorine are almost ubiquitous in waste of electrical and electronic equipment (WEEE and the knowledge of their content in the plastic fraction is an essential step for proper end of life management. The aim of this study is to compare the following analytical methods: energy dispersive X-ray fluorescence spectroscopy (ED-XRF, ion chromatography (IC, ion-selective electrodes (ISEs, and elemental analysis for the quantitative determination of chlorine and bromine in four real samples taken from different WEEE treatment plants, identifying the best analytical technique for waste management workers. Home-made plastic standard materials with known concentrations of chlorine or bromine have been used for calibration of ED-XRF and to test the techniques before the sample analysis. Results showed that IC and ISEs, based upon dissolution of the products of the sample combustion, have not always achieved a quantitative absorption of the analytes in the basic solutions and that bromine could be underestimated since several oxidation states occur after combustion. Elemental analysis designed for chlorine determination is subjected to strong interference from bromine and required frequent regeneration and recalibration of the measurement cell. The most reliable method seemed to be the non-destructive ED-XRF. Calibration with home-made standards, having a similar plastic matrix of the samples, enabled us to carry out quantitative determinations, which have been revealed to be satisfactorily accurate and precise. In all the analyzed samples a total concentration of chlorine and/or bromine between 0.6 and 4 w/w% was detected, compromising the feasibility of a mechanical recycling and suggesting the exploration of an alternative route for managing these plastic wastes.

  4. Hanford Site Hazardous waste determination report for transuranic debris waste streams NPFPDL2A

    Energy Technology Data Exchange (ETDEWEB)

    WINTERHALDER, J.A.

    1999-09-29

    This hazardous waste determination report (Report) describes the process and information used on the Hanford Site to determine that waste stream number NPFPDLZA, consisting of 30 containers of contact-handled transuranic debris waste, is not hazardous waste regulated by the Resource Conservation and Recovery Act (RCRA) or the New Mexico Hazardous Waste Act. For a waste to be hazardous under these statutes, the waste either must be specifically listed as a hazardous waste, or exhibit one or more of the characteristics of a hazardous waste, Le., ignitability, corrosivity, reactivity, or toxicity. Waste stream NPFPDLZA was generated, packaged, and placed into storage between 1993 and 1997. Extensive knowledge of the waste generating process, facility operational history, and administrative controls and operating procedures in effect at the time of generation, supported the initial nonhazardous waste determination. Because of the extent and reliability of information pertaining to this waste type, and the total volume of waste in the debris matrix parameter category, the Hanford Site is focusing initial efforts on this and similar waste streams for the first shipment to the Waste Isolation Pilot Plant (WIPP). RCRA regulations authorize hazardous waste determinations to be made either by using approved sampling and analysis methods or by applying knowledge of the waste in light of the materials or the process(es) used. This latter approach typically is referred to as process knowledge. The Transuranic Waste Characterization Quality Assurance Program Plan (CAO-94-1010) for WIPP refers to acceptable knowledge in essentially the same terms; acceptable knowledge as used throughout this Report is synonymous with the term process knowledge. The 30 containers addressed in this Report were characterized by the following methods: Acceptable knowledge; Nondestructive examination using real-time radiography; Visual examination; and Headspace gas sampling and analysis. The initial

  5. Discussion on the methodology for determining food waste in household waste composition studies.

    Science.gov (United States)

    Lebersorger, S; Schneider, F

    2011-01-01

    Food waste has become an increasingly discussed topic in recent years. However, there is little authoritative data on food waste quantities and composition and systematic and comparable data are missing. Household waste composition analyses, which are often carried out routinely at regular or irregular intervals, provide an opportunity for obtaining data about food waste at both local and regional levels. The results of prior waste composition studies are not really comparable due to the different classifications, definitions and methods used; in addition, these are mostly insufficiently described and not reproducible by a third party. The aim of this paper is to discuss a methodology for determining the proportion of food waste in household waste composition studies, by analysing specific problems and possible solutions. For that purpose, findings from the literature are analysed and the approach and results of a composition analysis of residual waste of a stratified sample (urban, rural area) are presented. The study suggests that in order to avoid a significant loss of information, waste should not be sieved before sorting and packed food waste should be classified into the relevant food waste category together with its packaging. The case study showed that the overall influence of the proportion of food packaging included in the food waste category, which amounted to only 8%, did not significantly influence the results and can therefore be disregarded. Copyright © 2011 Elsevier Ltd. All rights reserved.

  6. CATALYTIC CONVERSION OF MUNICIPAL WASTE PLASTIC INTO GASOLINE-RANGE PRODUCTS OVER MESOPOROUS MATERIALS

    Institute of Scientific and Technical Information of China (English)

    Jorge Norberto Beltramini

    2006-01-01

    In the last 20 years, it has become apparent that waste produced from plastics was becoming an environmental problem because of their low biodegradability. Though several methods have been proposed for recycling waste plastics, it is generally accepted that material recovery is not a long-term solution to the present problem, and that energy or chemical recovery is a more attractive alternative, including cracking into the monomer constituents, combustion to produce energy, and thermal or catalytic conversion to produce useful intermediate chemicals.This paper is a contribution in the area of the last option for energy recovery. There have been a number of publications reporting the use of molecular sieves and amorphous silica-alumina catalysts for the cracking of polymers into a range of hydrocarbons. The research work reported here demonstrates the ability of mesoporous catalysts in cracking polyethylene into gasoline range products.It was found that for mesoporous MCM-41 catalysts, its cracking activity increases with its crystallinity, displaying higher activity with smaller pore diameters. The hydrocarbon product distribution strongly indicates a carbenium ion cracking mechanism. The product distribution was also compared with those obtained from thermal cracking tests.

  7. Usage of waste products from thermal recycling of plastics waste in enhanced oil recovery or in-situ coal conversion

    Energy Technology Data Exchange (ETDEWEB)

    Fink, M.; Fink, J.K. [Montanuniversitaet Leoben (Austria)

    1998-09-01

    In this contribution a thermal method for crude oil mobilization and in-situ liquefaction of coal is discussed, which will finally yield more organic material, as which has been put in from plastics waste originally into the process. The conversion product from thermal treatment is pumped down into exhausted crude oil reservoirs, where the hydrogen can degrade the residual high viscous oil to cause it to become more prone to flow so that it can be recovered. Such a process will envision two goals: 1. more organic raw material (as crude oil) will be recovered than is initially put in as waste product. 2. atmospheric pollutants from the conversion plant will be trapped in the reservoir, which simplifies the construction of the plant. An analogous process may be performed with coal seams. Coal seams with their high porosity and large specific surface are believed to be in particular useful to filter atmospheric pollutants. Depending on the type of coal the mobilization of organic material by this process may be in the background. (orig./SR)

  8. Conversion of Low Density Polyethylene (LDPE) and Polypropylene (PP) Waste Plastics into Liquid Fuel Using Thermal Cracking Process

    OpenAIRE

    Sarker, Moinuddin; Rashid, Mohammad Mamunor; Rahman, Md. Sadikur; Molla, Mohammed

    2012-01-01

    In every sector of the world today energy is essential. Energy has many forms such as electricity, transportation fuel and so on. A large amount of energy is produced from crude oil, which is used to produce petroleum and petroleum to produce daily usable plastics. The solution to the above mentioned problems can be solved through the utilization of the new develop technology. This new developed technology will remove these hazardous waste plastics from the environment and convert them into e...

  9. Preparation of activated carbon from waste plastics polyethylene terephthalate as adsorbent in natural gas storage

    Science.gov (United States)

    Yuliusman; Nasruddin; Sanal, A.; Bernama, A.; Haris, F.; Ramadhan, I. T.

    2017-02-01

    The main problem is the process of natural gas storage and distribution, because in normal conditions of natural gas in the gas phase causes the storage capacity be small and efficient to use. The technology is commonly used Compressed Natural Gas (CNG) and Liquefied Natural Gas (LNG). The weakness of this technology safety level is low because the requirement for high-pressure CNG (250 bar) and LNG requires a low temperature (-161°C). It takes innovation in the storage of natural gas using the technology ANG (Adsorbed Natural Gas) with activated carbon as an adsorbent, causing natural gas can be stored in a low pressure of about 34.5. In this research, preparation of activated carbon using waste plastic polyethylene terephthalate (PET). PET plastic waste is a good raw material for making activated carbon because of its availability and the price is a lot cheaper. Besides plastic PET has the appropriate characteristics as activated carbon raw material required for the storage of natural gas because the material is hard and has a high carbon content of about 62.5% wt. The process of making activated carbon done is carbonized at a temperature of 400 ° C and physical activation using CO2 gas at a temperature of 975 ° C. The parameters varied in the activation process is the flow rate of carbon dioxide and activation time. The results obtained in the carbonization process yield of 21.47%, while the yield on the activation process by 62%. At the optimum process conditions, the CO2 flow rate of 200 ml/min and the activation time of 240 minutes, the value % burn off amounted to 86.69% and a surface area of 1591.72 m2/g.

  10. Co-pyrolysis of swine manure with agricultural plastic waste: laboratory-scale study.

    Science.gov (United States)

    Ro, Kyoung S; Hunt, Patrick G; Jackson, Michael A; Compton, David L; Yates, Scott R; Cantrell, Keri; Chang, SeChin

    2014-08-01

    Manure-derived biochar is the solid product resulting from pyrolysis of animal manures. It has considerable potential both to improve soil quality with high levels of nutrients and to reduce contaminants in water and soil. However, the combustible gas produced from manure pyrolysis generally does not provide enough energy to sustain the pyrolysis process. Supplementing this process may be achieved with spent agricultural plastic films; these feedstocks have large amounts of available energy. Plastic films are often used in soil fumigation. They are usually disposed in landfills, which is wasteful, expensive, and environmentally unsustainable. The objective of this work was to investigate both the energetics of co-pyrolyzing swine solids with spent plastic mulch films (SPM) and the characteristics of its gas, liquid, and solid byproducts. The heating value of the product gas from co-pyrolysis was found to be much higher than that of natural gas; furthermore, the gas had no detectable toxic fumigants. Energetically, sustaining pyrolysis of the swine solids through the energy of the product gas could be achieved by co-pyrolyzing dewatered swine solids (25%m/m) with just 10% SPM. If more than 10% SPM is used, the co-pyrolysis would generate surplus energy which could be used for power generation. Biochars produced from co-pyrolyzing SPM and swine solid were similar to swine solid alone based on the surface area and the (1)H NMR spectra. The results of this study demonstrated the potential of using pyrolysis technology to manage two prominent agricultural waste streams (SPM and swine solids) while producing value-added biochar and a power source that could be used for local farm operations. Published by Elsevier Ltd.

  11. Determinants of consumer food waste behaviour: Two routes to food waste.

    Science.gov (United States)

    Stancu, Violeta; Haugaard, Pernille; Lähteenmäki, Liisa

    2016-01-01

    Approximately one quarter of the food supplied for human consumption is wasted across the food supply chain. In the high income countries, the food waste generated at the household level represents about half of the total food waste, making this level one of the biggest contributors to food waste. Yet, there is still little evidence regarding the determinants of consumers' food waste behaviour. The present study examines the effect of psycho-social factors, food-related routines, household perceived capabilities and socio-demographic characteristics on self-reported food waste. Survey data gathered among 1062 Danish respondents measured consumers' intentions not to waste food, planning, shopping and reuse of leftovers routines, perceived capability to deal with household food-related activities, injunctive and moral norms, attitudes towards food waste, and perceived behavioural control. Results show that perceived behavioural control and routines related to shopping and reuse of leftovers are the main drivers of food waste, while planning routines contribute indirectly. In turn, the routines are related to consumers' perceived capabilities to deal with household related activities. With regard to intentional processes, injunctive norms and attitudes towards food waste have an impact while moral norms and perceived behavioural control make no significant contribution. Implications of the study for initiatives aimed at changing consumers' food waste behaviour are discussed.

  12. 40 CFR 260.30 - Non-waste determinations and variances from classification as a solid waste.

    Science.gov (United States)

    2010-07-01

    ... from classification as a solid waste. 260.30 Section 260.30 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED) HAZARDOUS WASTE MANAGEMENT SYSTEM: GENERAL Rulemaking Petitions § 260.30 Non-waste determinations and variances from classification as a solid waste....

  13. Recycling and recovery routes of plastic solid waste (PSW): a review.

    Science.gov (United States)

    Al-Salem, S M; Lettieri, P; Baeyens, J

    2009-10-01

    Plastic solid waste (PSW) presents challenges and opportunities to societies regardless of their sustainability awareness and technological advances. In this paper, recent progress in the recycling and recovery of PSW is reviewed. A special emphasis is paid on waste generated from polyolefinic sources, which makes up a great percentage of our daily single-life cycle plastic products. The four routes of PSW treatment are detailed and discussed covering primary (re-extrusion), secondary (mechanical), tertiary (chemical) and quaternary (energy recovery) schemes and technologies. Primary recycling, which involves the re-introduction of clean scrap of single polymer to the extrusion cycle in order to produce products of the similar material, is commonly applied in the processing line itself but rarely applied among recyclers, as recycling materials rarely possess the required quality. The various waste products, consisting of either end-of-life or production (scrap) waste, are the feedstock of secondary techniques, thereby generally reduced in size to a more desirable shape and form, such as pellets, flakes or powders, depending on the source, shape and usability. Tertiary treatment schemes have contributed greatly to the recycling status of PSW in recent years. Advanced thermo-chemical treatment methods cover a wide range of technologies and produce either fuels or petrochemical feedstock. Nowadays, non-catalytic thermal cracking (thermolysis) is receiving renewed attention, due to the fact of added value on a crude oil barrel and its very valuable yielded products. But a fact remains that advanced thermo-chemical recycling of PSW (namely polyolefins) still lacks the proper design and kinetic background to target certain desired products and/or chemicals. Energy recovery was found to be an attainable solution to PSW in general and municipal solid waste (MSW) in particular. The amount of energy produced in kilns and reactors applied in this route is sufficiently

  14. Quality restoration of waste polyolefin plastic material through the dissolution-reprecipitation technique

    Directory of Open Access Journals (Sweden)

    Hadi Jasim Arkan

    2014-01-01

    Full Text Available This study examines the restoration of waste plastic polymers based on LDPE, HDPE or PP through dissolution/reprecipitation. Experimental conditions of the recycling process, including type of solvent/non-solvent, original polymer concentration and dissolution temperature were optimized. Results revealed that by using the different prepared solvents/non-solvents at various ratios and temperatures, the polymer recovery was always greater than 94%. The FTIR spectra and the thermal properties (melting point and crystallinity of the polymers before and after recycling were measured using Differential Scanning Calorimetry (DSC. Mechanical properties of the waste polymer before and after recycling were also measured. Besides small occasional deviations, the properties did not change. The tensile strength at maximum load was 7.1, 18.8, and 7.4 MPa for the recycled LDPE, HDPE and PP, respectively and 7.78, 18.54 and 7.86 MPa for the virgin polymer. For the waste, the strength was 6.2, 15.58 and 6.76 MPa.

  15. 废旧酚醛塑料回收和再利用方法研究%Study on Recycling Method of Waste Phenolic Plastics

    Institute of Scientific and Technical Information of China (English)

    何平; 吴仲伟; 潘绍波; 陈从升; 李辉

    2013-01-01

    介绍目前废旧塑料回收再利用技术的主要方法和不足之处,提出基于机械物理法的热固性塑料回收再利用方法,确定热固性塑料回收再利用的工艺流程。通过对热固性酚醛塑料回收再生试验,验证了机械物理法回收再生的可行性,最后对再生试样进行力学性能测试。结果表明,回收再生酚醛/聚丙烯共混料的拉伸强度与弯曲强度分别达到6 MPa和13 MPa以上,能满足回收再利用的要求。%Main methods and shortcomings about recycling technology of waste plastics were introduced,and the recycling mechanism of the waste thermosetting plastics based on mechanical and physical method was presented. Accordingly,the recycling process of waste thermosetting plastics was determined. By means of recycling and regeneration experiment on thermosetting phenolic plastics,the feasibility of recycling and regeneration based on mechanical and physical method was verified.At last,the mechanical properties of regeneration specimens were tested. The results show that tensile strength and bending strength of recycling phenolic/polypropylene plastics can reach 6 MPa and 13 MPa respectively,and it meets the recycling requirements.

  16. A study on synthesis of energy fuel from waste plastic and assessment of its potential as an alternative fuel for diesel engines.

    Science.gov (United States)

    Kaimal, Viswanath K; Vijayabalan, P

    2016-05-01

    The demand for plastic is ever increasing and has produced a huge amount of plastic waste. The management and disposal of plastic waste have become a major concern, especially in developing cities. The idea of waste to energy recovery is one of the promising techniques used for managing the waste plastic. This paper assesses the potential of using Waste Plastic Oil (WPO), synthesized using pyrolysis of waste plastic, as an alternative for diesel fuel. In this research work, the performance and emission characteristics of a single cylinder diesel engine fuelled with WPO and its blends with diesel are studied. In addition to neat plastic oil, three blends (PO25, PO50 and PO75) were prepared on a volumetric basis and the engine was able to run on neat plastic oil. Brake thermal efficiency of blends was lower compared to diesel, but PO25 showed similar performance to that of diesel. The emissions were reduced considerably while using blends when compared to neat plastic oil. The smoke and NOX were reduced by 22% and 17.8% respectively for PO25 than that of plastic oil. Copyright © 2016 Elsevier Ltd. All rights reserved.

  17. STUDY ON THE RECYCLING SYSTEM OF WASTE PLASTICS AND MIXED PAPER FROM A LONG-TERM PERSPECTIVE

    Science.gov (United States)

    Fujii, Minoru; Fujita, Tsuyoshi; Chen, Xudong; Ohnishi, Satoshi; Osako, Masahiro; Moriguchi, Yuichi; Yamaguchi, Naohisa

    Plastics and mixed paper in municipal solid waste are valuable resources with high calorific value. However, the recycling cost to utilize them tends to be expensive. In addition, recycling system has to be consistent with the reduce of wastes on which should be put higher-priority to lower carbon emission and save resources in the long term. In this paper, we proposed a recycling system (smart recycling system) which consists of a local center an d existing facilities in arterial industries. In the local center, collected waste plastics and mixed paper from household are processed on the same line into a form suitable for transportation and handling in a facility of arterial in dustry which can utilize those wastes effectively. At the same time, a part of plastics with high quality is processed into a recycled resin in the center. It was suggested that, by utilizing existing facilities in arterial industries which have enough and flexible capacity to accept those wastes, the system can be a robust system even if the amount of wastes generation fluctuates widely. The effect of CO2 reduction and cost by installing the system were calculated and it was estimated that 3.5 million ton of additional annual CO2 reduction could be brought in Tokyo and surrounding three prefectures without co nsiderable increase in cost.

  18. Brominated flame retardant emissions from the open burning of five plastic wastes and implications for environmental exposure in China.

    Science.gov (United States)

    Ni, Hong-Gang; Lu, Shao-You; Mo, Ting; Zeng, Hui

    2016-07-01

    Based on the most widely used plastics in China, five plastic wastes were selected for investigation of brominated flame retardant (BFR) emission behaviors during open burning. Considerable variations were observed in the emission factors (EF) of polybrominated diphenyl ethers (PBDEs) and hexabromocyclododecanes (HBCDs) from the combustion of different plastic wastes. Distribution of BFR output mass showed that ΣPBDE was emitted mainly by the airborne particle (51%), followed by residual ash (44%) and the gas phase (5.1%); these values for ΣHBCD were 62%, 24%, and 14%, respectively. A lack of mass balance after the burning of the plastic wastes for some congeners (output/input mass ratios>1) suggested that formation and survival exceeded PBDE decomposition during the burns. However, that was not the case for HBCD. A comparison with literature data showed that the open burning of plastic waste is major source of PBDE compared to regulated combustion activities. Even for state-of-the-art waste incinerators equipped with sophisticated complex air pollution control technologies, BFRs are released on a small scale to the environment. According to our estimate, ΣPBDE release to the air and land from municipal solid waste (MSW) incineration plants in China in 2015 were 105 kg/year and 7124 kg/year. These data for ΣHBCD were 25.5 and 71.7 kg/year, respectively. Considering the fact that a growing number of cities in China are switching to incineration as the preferred method for MSW treatment, our estimate is especially important. This study provides the first data on the environmental exposure of BFRs emitted from MSW incineration in China.

  19. Facile Route to Generate Fuel Oil via Catalytic Pyrolysis of Waste Polypropylene Bags: Towards Waste Management of >20 μm Plastic Bags

    Directory of Open Access Journals (Sweden)

    Neeraj Mishra

    2014-01-01

    Full Text Available A novel strategy of waste recycling of polypropylene plastics (PP bags for generation of commercially viable byproducts using nanoforms of nickel as catalyst is presented in this work. After pyrolysis of waste PP bags (>20 μm under continuous argon flow, 90% conversion efficiency to high petroleum oil was observed at 550°C. To assess the physicochemical attributes of formed oil, flash point, pour point, viscosity, specific gravity, heating value, and density were also measured and found to be very close to ideal values of commercial fuel oil. Moreover, GC-MS was used to resolve the range of trace mass hydrocarbon present in the liquefied hydrocarbon. Our robust recycling system can be exploited as economical technique to solve the nuisance of waste plastic hazardous to ecosystem.

  20. Adhesion of different Candida spp. to plastic: XTT formazan determinations.

    Science.gov (United States)

    Hawser, S

    1996-01-01

    Adhesion of synchronized yeast-phase Candida cells to tissue culture plastic was investigated using the tetrazolium salt, XTT. The procedure permits the direct enumeration of adherent yeasts following the metabolic conversion of the XTT tetrazolium salt, to its reduced formazan form, by mitochondrial dehydrogenases. Using this procedure, the formation of XTT formazan by Candida cells was typically related to the inoculum size. The adhesion of Candida yeast-phase cells from different Candida spp. to plastic was of the following order: C. krusei (n = 5) > C. albicans (n = 10) > C. glabrata (n = 6). Furthermore, preliminary experiments with several other species indicated that C. tropicalis (n = 2) may adhere as well as C. albicans and that one strain each of C. guilliermondii and C. parapsilosis appear to adhere to plastic in a similar fashion to C. glabrata. The data indicate the utility of the XTT tetrazolium based assay in enumerating the adhesion of different Candida spp. to plastic.

  1. Determination of organochlorine pesticides adsorbed on plastic pellets

    OpenAIRE

    2016-01-01

    In the past years, several studies have revealed the presence of organic contaminants at concentrations from sub ng g–1 to mg g–1 on/in plastic pellets found in coastal environment worldwide [1,2,3]. Plastic pellets are actually industrial raw material, typically in the shape of small granules with a diameter of a few mm. They are categorized as microplastics (< 5 mm). They can be unintentionally lost in the environment during manufacturing and transport. They can subsequently ...

  2. Recovery of plastic wastes from dumpsite as refuse-derived fuel and its utilization in small gasification system.

    Science.gov (United States)

    Chiemchaisri, Chart; Charnnok, Boonya; Visvanathan, Chettiyappan

    2010-03-01

    An effort to utilize solid wastes at dumpsite as refuse-derived fuel (RDF) was carried out. The produced RDF briquette was then utilized in the gasification system. These wastes were initially examined for their physical composition and chemical characteristics. The wastes contained high plastic content of 24.6-44.8%, majority in polyethylene plastic bag form. The plastic wastes were purified by separating them from other components through manual separation and trommel screen after which their content increased to 82.9-89.7%. Subsequently, they were mixed with binding agent (cassava root) and transformed into RDF briquette. Maximum plastic content in RDF briquette was limit to 55% to maintain physical strength and maximum chlorine content. The RDF briquette was tested in a down-draft gasifier. The produced gas contained average energy content of 1.76 MJ/m(3), yielding cold gas efficiency of 66%. The energy production cost from this RDF process was estimated as USD0.05 perkWh.

  3. Sulfur Distribution during Hydrothermal Liquefaction of Lignite, Wheat Straw and Plastic Waste in Sub-Critical Water

    Institute of Scientific and Technical Information of China (English)

    Wang Baofeng; Huang Yaru; Zhang Jinjun

    2015-01-01

    The distribution and transformation of sulfur in products during hydrothermal liquefaction of lignite, wheat straw and plastic waste in sub-critical water were investigated in an autoclave. The inlfuence of blending ratio, temperature, initial nitrogen pressure, residence time and additives on sulfur distribution was studied systematically. The results showed that most of sulfur existed as organic sulfur and transferred into the residue, and only a small part of sulfur transferred into oil and gas during hydrothermal liquefaction of lignite, wheat straw and plastic waste in sub-critical water. The results also showed that lower temperature (less than 300℃) was favorable for obtaining oil with low sulfur content. It can be also seen from the results that the best condition to obtain the oil with low sulfur content should be implemented at a lignite/wheat straw/plastic waste blending ratio of 5:4:1, an initial nitrogen pressure of 3 MPa and a residence time of 30 minutes. Fur-thermore, the results indicated that adding tourmaline during hydrothermal liquefaction of lignite, wheat straw and plastic waste was beneifcial to production of oil with low sulfur content.

  4. Task 3 - pyrolysis of plastic waste. Semi-annual report, April 1--September 30, 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-05-01

    This report briefly describes progress in the development of a thermal decomposition process for volume reduction of spent ion-exchange resin. During the reporting period, two series of tests were performed. The mixed waste plastics test investigated the effectiveness of the process in concentrating radionuclide surrogates in a solids residual while yielding a surrogate-free condensate product. Preliminary results indicated the occurrence of solids carryover. The ion-exchange resin tests resulted in a cesium concentration in the unfiltered condensate of about 4 to 20 micrograms/gram, indicating that fine particulate material was passing through the reactor cyclone. Future work includes the evaluation of an auger reactor in place of the fluidized bed reactor to address the problem of reactor carryover. 2 figs., 7 tabs.

  5. Preparation and performance of rare earth Zr catalyst for reforming waste plastics cracking product

    Institute of Scientific and Technical Information of China (English)

    袁兴中; 曾光明; 陈晓青; 陈志勇; 鄢钢

    2003-01-01

    The rare earth Zr catalyst, whose carrier was Al2O3, was prepared by co-precipitation with Zr(NO3)2,Al(NO3 )3, and(NH2)2CO as the raw materials. The obtained catalyst was used to reform the waste plastic crackingproduct. As the Zr content in the catalyst increases, the yields of gasoline, gas, and the rate of carbon deposition in-crease, but the yields of diesel and heavy oil decrease. The optimum Zr content of the catalyst is 5%. At 290 ℃,with this most suitable catalyst, the yield of liquid fuel oil is the highest, about 86.10%, and research octance num-ber(RON) of the gasoline is 92.15.

  6. Standard test method for determining liquidus temperature of immobilized waste glasses and simulated waste glasses

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2011-01-01

    1.1 These practices cover procedures for determining the liquidus temperature (TL) of nuclear waste, mixed nuclear waste, simulated nuclear waste, or hazardous waste glass in the temperature range from 600°C to 1600°C. This method differs from Practice C829 in that it employs additional methods to determine TL. TL is useful in waste glass plant operation, glass formulation, and melter design to determine the minimum temperature that must be maintained in a waste glass melt to make sure that crystallization does not occur or is below a particular constraint, for example, 1 volume % crystallinity or T1%. As of now, many institutions studying waste and simulated waste vitrification are not in agreement regarding this constraint (1). 1.2 Three methods are included, differing in (1) the type of equipment available to the analyst (that is, type of furnace and characterization equipment), (2) the quantity of glass available to the analyst, (3) the precision and accuracy desired for the measurement, and (4) candi...

  7. Electrostatic separator for micronized mixtures of metals and plastics originating from waste electric and electronic equipment

    Science.gov (United States)

    Messal, Sara; Corondan, Razvan; Chetan, Ionut; Ouiddir, Rabah; Medles, Karim; Dascalescu, Lucian

    2015-10-01

    In spite of their extensive use for processing mixtures of granules exceeding 1 mm in size, very few industrial electrostatic separators are capable of handling micronized metals and plastics originating from waste electric and electronic equipment. The aim of the present work is to validate the possibility of using a novel belt-type electrostatic separator for the selective sorting of such particulate mixtures, the dimensions of which are in the order of 0.1 mm. In this type of separator, the metal particles get charged by electrostatic induction in contact with the grounded metal belt electrode, while the plastics remain uncharged in the electric field and are collected separately. The experiments are performed with 2-g samples of a mixture composed in equal proportions (50% - 50%) of Aluminium and Acrylonitrile Butadiene Styrene (ABS) particles of average diameter ranging between 125 μm and 250 μm. They enabled the evaluation of the effects and the interaction of two control variables of the process: the angle of inclination of the roll-type electrode and the high voltage applied to it.

  8. Bromine in plastic consumer products - Evidence for the widespread recycling of electronic waste.

    Science.gov (United States)

    Turner, Andrew; Filella, Montserrat

    2017-12-01

    A range of plastic consumer products and components thereof have been analysed by x-ray fluorescence (XRF) spectrometry in a low density mode for Br as a surrogate for brominated flame retardant (BFR) content. Bromine was detected in about 42% of 267 analyses performed on electronic (and electrical) samples and 18% of 789 analyses performed on non-electronic samples, with respective concentrations ranging from 1.8 to 171,000μgg(-1) and 2.6 to 28,500μgg(-1). Amongst the electronic items, the highest concentrations of Br were encountered in relatively small appliances, many of which predated 2005 (e.g. a fan heater, boiler thermostat and smoke detector, and various rechargers, light bulb collars and printed circuit boards), and usually in association with Sb, a component of antimony oxide flame retardant synergists, and Pb, a heavy metal additive and contaminant. Amongst the non-electronic samples, Br concentrations were highest in items of jewellery, a coffee stirrer, a child's puzzle, a picture frame, and various clothes hangers, Christmas decorations and thermos cup lids, and were often associated with the presence of Sb and Pb. These observations, coupled with the presence of Br at concentrations below those required for flame-retardancy in a wider range of electronic and non-electronic items, are consistent with the widespread recycling of electronic plastic waste. That most Br-contaminated items were black suggests the current and recent demand for black plastics in particular is met, at least partially, through this route. Given many Br-contaminated items would evade the attention of the end-user and recycler, their disposal by conventional municipal means affords a course of BFR entry into the environment and, for food-contact items, a means of exposure to humans. Copyright © 2017 Elsevier B.V. All rights reserved.

  9. The pollution characteristics of odor, volatile organochlorinated compounds and polycyclic aromatic hydrocarbons emitted from plastic waste recycling plants.

    Science.gov (United States)

    Tsai, Chung-Jung; Chen, Mei-Lien; Chang, Keng-Fu; Chang, Fu-Kuei; Mao, I-Fang

    2009-02-01

    Plastic waste treatment trends toward recycling in many countries; however, the melting process in the facilities which adopt material recycling method for treating plastic waste may emit toxicants and cause sensory annoyance. The objectives of this study were to analyze the pollution characteristics of the emissions from the plastic waste recycling plants, particularly in harmful volatile organochlorinated compounds, polycyclic aromatic hydrocarbons (PAHs), odor levels and critical odorants. Ten large recycling plants were selected for analysis of odor concentration (OC), volatile organic compounds (VOCs) and PAHs inside and outside the plants using olfactometry, gas chromatography-mass spectrometry and high performance liquid chromatography-fluorescence detector, respectively. The olfactometric results showed that the melting processes used for treating polyethylene/polypropylene (PE/PP) and polyvinyl chloride (PVC) plastic waste significantly produced malodor, and the odor levels at downwind boundaries were 100-229 OC, which all exceeded Taiwan's EPA standard of 50 OC. Toluene, ethylbenzene, 4-methyl-2-pentanone, methyl methacrylate and acrolein accounted for most odors compared to numerous VOCs. Sixteen organochlorinated compounds were measured in the ambient air emitted from the PVC plastic waste recycling plant and total concentrations were 245-553 microg m(-3); most were vinyl chloride, chloroform and trichloroethylene. Concentrations of PAHs inside the PE/PP plant were 8.97-252.16 ng m(-3), in which the maximum level were 20-fold higher than the levels detected from boundaries. Most of these recycling plants simply used filter to treat the melting fumes, and this could not efficiently eliminate the gaseous compounds and malodor. Improved exhaust air pollution control were strongly recommended in these industries.

  10. Difficulties Regarding Determination of Plasticity Index of Silty Soils by use of Casagrande and Fall Cone Methods

    DEFF Research Database (Denmark)

    Poulsen, Rikke; Ibsen, Lars Bo; Nielsen, Benjaminn Nordahl

    Soil plasticity index and thereby the liquid limit and plastic limit are often used in order to classify the soil type and determine soil properties.......Soil plasticity index and thereby the liquid limit and plastic limit are often used in order to classify the soil type and determine soil properties....

  11. Thermo-Catalytic Pyrolysis of Waste Plastics from End of Life Vehicle

    Directory of Open Access Journals (Sweden)

    Miskolczi Norbert

    2016-01-01

    Full Text Available Pyrolysis of waste plastics is widely used recycling method. Owing to the end-of-life vehicles regulations, 95% of passenger cars and vehicles must reused/recovered after the dismantling. Pyrolysis of waste polyethylene and polypropylene obtained from end-of-life vehicles was investigated in a continuously stirred batch reactor using 500 and 600°C temperatures. To ensure the pyrolysis reactions the tested catalysts (5% of ZSM-5, HZSM-5, Ni-ZSM-5 and Fe-ZSM-5 were added directly to the mixtures of raw materials. Products of pyrolysis were separated into gases, pyrolysis oil and heavy oil, which was further analyzed by gas-chromatography, Fourier transformed infrared spectroscopy and other standardized methods. Based on the results it was concluded, that the catalysts significantly increase the yields of volatile products, and modify their composition. Especially the alkane/alkene ratio, the methane concentration and the concentration of branched hydrocarbon could be affected by the applied catalysts. Ni-ZSM-5 catalyst had the highest activity in methane production, while HZSM-5 catalyst proved effective in isomerization reactions. Using H-ZSM-5, Ni-ZSM-5, and Fe-ZSM-5 catalyst notably decreased average molecular weight of pyrolysis oils and significantly higher aromatic content was observed.

  12. Characterisation of recycled mixed plastic solid wastes: Coupon and full-scale investigation.

    Science.gov (United States)

    Bajracharya, Rohan Muni; Manalo, Allan C; Karunasena, Warna; Lau, Kin-Tak

    2016-02-01

    In Australia, the plastic solid waste (PSW) comprises 16% by weight of municipal solid waste but only about one-fourth are recycled. One of the best options to increase the recycling rate of mixed PSW is to convert them into products suitable for construction. However, a comprehensive understanding on the mechanical behaviour of mixed PSW under different loading conditions is important for their widespread use as a construction material. This study focuses on investigating the mechanical behaviour of recycled mixed PSW containing HDPE, LDPE and PP using coupon and full-scale specimens. From coupon test, the strength values were found to be 14.8, 19.8, 20, 5.6MPa in tension, compression, flexure and shear respectively, while the modulus of elasticity are 0.91, 1.03, 0.72GPa in tension, compression and flexure respectively. The coefficient of variance of the measured properties for coupon and fullscale specimens was less than 10% indicating that consistent material properties can be obtained for mixed PSW. More importantly, the strength properties of mixed PSW are comparable to softwood structural timber. The flexural behaviour of full-scale specimens was also predicted using fibre model analysis and finite element modelling. Comparison showed that using coupon specimen's properties, the flexural behaviour of the full-scale specimens can be predicted reliably which can eliminate the costly and time consuming arrangements for full-scale experimental tests.

  13. Upcycling : converting waste plastics into paramagnetic, conducting, solid, pure carbon microspheres.

    Energy Technology Data Exchange (ETDEWEB)

    Pol, V.

    2010-06-15

    The recent tremendous increase in the volume of waste plastics (WP) will have a harmful environmental impact on the health of living beings. Hundreds of years are required to degrade WP in atmospheric conditions. Hence, in coming years, in addition to traditional recycling services, innovative 'upcycling' processes are necessary. This article presents an environmentally benign, solvent-free autogenic process that converts various WP [low density polyethylene (LDPE), high density polyethylene (HDPE), polyethylene terephthalate (PET), polystyrene (PS), or their mixtures] into carbon microspheres (CMSs), an industrially significant, value-added product. The thermal dissociation of these individual or mixed WP in a closed reactor under autogenic pressure (1000 psi) produced dry, pure powder of CMSs. In this paper, the optimization of process parameters such as the effect of mixing of WP with other materials, and the role of reaction temperature and time are reported. Employing advanced analytical techniques, the atomic structure, composition, and morphology of as-obtained CMSs were analyzed. The room-temperature paramagnetism in CMSs prepared from waste LDPE, HDPE, and PS was further studied by electron paramagnetic resonance (EPR). The conducting and paramagnetic nature of CMSs holds promise for their potential applications in toners, printers, paints, batteries, lubricants, and tires.

  14. Pyrolysis of municipal plastic wastes II: Influence of raw material composition under catalytic conditions.

    Science.gov (United States)

    López, A; de Marco, I; Caballero, B M; Laresgoiti, M F; Adrados, A; Torres, A

    2011-01-01

    In this work, the results obtained in catalytic pyrolysis of three plastic waste streams which are the rejects of an industrial packing wastes sorting plant are presented. The samples have been pyrolysed in a 3.5 dm(3) reactor under semi-batch conditions at 440 °C for 30 min in nitrogen atmosphere. Commercial ZSM-5 zeolite has been used as catalyst in liquid phase contact. In every case, high HHV gases and liquids which can be useful as fuels or source of chemicals are obtained. A solid fraction composed of the inorganic material contained in the raw materials and some char formed in the pyrolysis process is also obtained. The zeolite has shown to be very effective to produce liquids with great aromatics content and C3-C4 fraction rich gases, even though the raw material was mainly composed of polyolefins. The characteristics of the pyrolysis products as well as the effect of the catalyst vary depending on the composition of the raw material. When paper rich samples are pyrolysed, ZSM-5 zeolite increases water production and reduces CO and CO(2) generation. If stepwise pyrolysis is applied to such sample, the aqueous liquid phase can be separated from the organic liquid fraction in a first low temperature step.

  15. Chemical recycling of plastic wastes made from polyethylene (LDPE and HDPE) and polypropylene (PP).

    Science.gov (United States)

    Achilias, D S; Roupakias, C; Megalokonomos, P; Lappas, A A; Antonakou, Epsilon V

    2007-11-19

    The recycling of either model polymers or waste products based on low-density polyethylene (LDPE), high-density polyethylene (HDPE) or polypropylene (PP) is examined using the dissolution/reprecipitation method, as well as pyrolysis. In the first technique, different solvents/non-solvents were examined at different weight percent amounts and temperatures using as raw material both model polymers and commercial products (packaging film, bags, pipes, food-retail outlets). The recovery of polymer in every case was greater than 90%. FT-IR spectra and tensile mechanical properties of the samples before and after recycling were measured. Furthermore, catalytic pyrolysis was carried out in a laboratory fixed bed reactor with an FCC catalyst using again model polymers and waste products as raw materials. Analysis of the derived gases and oils showed that pyrolysis gave a mainly aliphatic composition consisting of a series of hydrocarbons (alkanes and alkenes), with a great potential to be recycled back into the petrochemical industry as a feedstock for the production of new plastics or refined fuels.

  16. Why are our children wasting: Determinants of wasting among under 5s in Ghana.

    Science.gov (United States)

    Darteh, Eugene Kofuor Maafo; Acquah, Evelyn; Darteh, Florie

    2017-09-01

    Wasting is one of the indicators of malnutrition known to contribute to the deaths occurring from childhood malnutrition. It is the measure of body mass in relation to body length used to explain recent nutritional status. This paper examines the determinants of wasting among under 5s in Ghana. Data were drawn from the 2014 Ghana Demographic and Health Survey children's records file to examine the determinants of wasting among children. A total of 2720 children under 5 years with valid anthropometric data were used. Data on wasting were collected by measuring the weight and height of all children under 5 years of age. Bi-variate and multi-variate statistics are used to examine the determinants of wasting. The bi-variate analysis showed significant differences ( p 5s according to age of the child, region, and wealth status. On the other hand, the multi-variate analysis revealed that the odds of wasting were lower among children aged 24-35 months (Odds ratio (OR) = 0.37; p 5s. Also, efforts should be made by the relevant government agencies and other stakeholders to strengthen the socio-economic status of mothers to enable them to provide adequate nutrition and improve access to health insurance for their children in order to reduce the incidence of wasting among these children.

  17. Hazardous Waste Code Determination for First/Second-Stage Sludge Waste Stream (IDCs 001, 002, 800)

    Energy Technology Data Exchange (ETDEWEB)

    Arbon, R.E.

    2001-01-31

    This document, Hazardous Waste Code Determination for the First/Second-Stage Sludge Waste Stream, summarizes the efforts performed at the Idaho National Engineering and Environmental Laboratory (INEEL) to make a hazardous waste code determination on Item Description Codes (IDCs) 001, 002, and 800 drums. This characterization effort included a thorough review of acceptable knowledge (AK), physical characterization, waste form sampling, chemical analyses, and headspace gas data. This effort included an assessment of pre-Waste Analysis Plan (WAP) solidified sampling and analysis data (referred to as preliminary data). Seventy-five First/Second-Stage Sludge Drums, provided in Table 1-1, have been subjected to core sampling and analysis using the requirements defined in the Quality Assurance Program Plan (QAPP). Based on WAP defined statistical reduction, of preliminary data, a sample size of five was calculated. That is, five additional drums should be core sampled and analyzed. A total of seven drums were sampled, analyzed, and validated in compliance with the WAP criteria. The pre-WAP data (taken under the QAPP) correlated very well with the WAP compliant drum data. As a result, no additional sampling is required. Based upon the information summarized in this document, an accurate hazardous waste determination has been made for the First/Second-Stage Sludge Waste Stream.

  18. Determining Machining Parameters of Corn Byproduct Filled Plastics

    Science.gov (United States)

    In a collaborative project between the USDA and Northern Illinois University, the use of corn ethanol processing byproducts (i.e., DDGS) as bio-filler materials in the compression molding of phenolic plastics has been studied. This paper reports on the results of a machinability study in the milling...

  19. Determination of Machining Parameters of Corn Byproduct Filled Plastics

    Science.gov (United States)

    In a collaborative project between the USDA and Northern Illinois University, the use of ethanol corn processing by-products as bio-filler materials in the compression molding of phenolic plastics has been studied. This paper reports on the results of a machinability study in the milling of various ...

  20. Case study: Is the 'catch-all-plastics bin' useful in unlocking the hidden resource potential in the residual waste collection system?

    Science.gov (United States)

    Kranzinger, Lukas; Schopf, Kerstin; Pomberger, Roland; Punesch, Elisabeth

    2017-02-01

    Austria's performance in the collection of separated waste is adequate. However, the residual waste still contains substantial amounts of recyclable materials - for example, plastics, paper and board, glass and composite packaging. Plastics (lightweight packaging and similar non-packaging materials) are detected at an average mass content of 13% in residual waste. Despite this huge potential, only 3% of the total amount of residual waste (1,687,000 t y(-1)) is recycled. This implies that most of the recyclable materials contained in the residual waste are destined for thermal recovery and are lost for recycling. This pilot project, commissioned by the Land of Lower Austria, applied a holistic approach, unique in Europe, to the Lower Austrian waste management system. It aims to transfer excess quantities of plastic packaging and non-packaging recyclables from the residual waste system to the separately collected waste system by introducing a so-called 'catch-all-plastics bin'. A quantity flow model was constructed and the results showed a realistic increase in the amount of plastics collected of 33.9 wt%. This equals a calculated excess quantity of 19,638 t y(-1). The increased plastics collection resulted in a positive impact on the climate footprint (CO2 equivalent) in line with the targets of EU Directive 94/62/EG (Circular Economy Package) and its Amendments. The new collection system involves only moderate additional costs.

  1. Contamination and risk of heavy metals in soils and sediments from a typical plastic waste recycling area in North China.

    Science.gov (United States)

    Tang, Zhenwu; Zhang, Lianzhen; Huang, Qifei; Yang, Yufei; Nie, Zhiqiang; Cheng, Jiali; Yang, Jun; Wang, Yuwen; Chai, Miao

    2015-12-01

    Plastic wastes are increasingly being recycled in many countries. However, available information on the metals released into the environment during recycling processes is rare. In this study, the contamination features and risks of eight heavy metals in soils and sediments were investigated in Wen'an, a typical plastic recycling area in North China. The surface soils and sediments have suffered from moderate to high metal pollution and in particular, high Cd and Hg pollution. The mean concentrations of Cd and Hg were 0.355 and 0.408 mg kg(-1), respectively, in the soils and 1.53 and 2.10 mg kg(-1), respectively, in the sediments. The findings suggested that there is considerable to high potential ecological risks in more than half of the soils and high potential ecological risk in almost all sediments. Although the health risk levels from exposure to soil metals were acceptable for adults, the non-carcinogenic risks to local children exceeded the acceptable level. Source assessment indicated that heavy metals in soils and sediments were mainly derived from inputs from poorly controlled plastic waste recycling operations in this area. The results suggested that the risks associated with heavy metal pollution from plastic waste recycling should be of great concern.

  2. Co-recycling of acrylonitrile-butadiene-styrene waste plastic and nonmetal particles from waste printed circuit boards to manufacture reproduction composites.

    Science.gov (United States)

    Sun, Zhixing; Shen, Zhigang; Zhang, Xiaojing; Ma, Shulin

    2015-01-01

    This study investigated the feasibility of using acrylonitrile-butadiene-styrene (ABS) waste plastic and nonmetal particles from waste printed circuit boards (WPCB) to manufacture reproduction composites (RC), with the aim of co-recycling these two waste resources. The composites were prepared in a twin-crew extruder and investigated by means of mechanical testing, in situ flexural observation, thermogravimatric analysis, and dimensional stability evaluation. The results showed that the presence of nonmetal particles significantly improved the mechanical properties and the physical performance of the RC. A loading of 30 wt% nonmetal particles could achieve a flexural strength of 72.6 MPa, a flexural modulus of 3.57 GPa, and an impact strength of 15.5 kJ/m2. Moreover, it was found that the application of maleic anhydride-grafted ABS as compatilizer could effectively promote the interfacial adhesion between the ABS plastic and the nonmetal particles. This research provides a novel method to reuse waste ABS and WPCB nonmetals for manufacturing high value-added product, which represents a promising way for waste recycling and resolving the environmental problem.

  3. Study on Conversion of Municipal Plastic Wastes into Liquid Fuel Compounds, Analysis of Crdi Engine Performance and Emission Characteristics

    Science.gov (United States)

    Divakar Shetty, A. S.; Kumar, R. Ravi; Kumarappa, S.; Antony, A. J.

    2016-09-01

    The rate of economic evolution is untenable unless we save or stops misusing the fossil fuels like coal, crude oil or fossil fuels. So we are in need of start count on the alternate or renewable energy sources. In this experimental analysis an attempt has been made to investigate the conversion of municipal plastic wastes like milk covers and water bottles are selected as feed stocks to get oil using pyrolysis method, the performance analysis on CRDI diesel engine and to assess emission characteristics like HC, CO, NOX and smoke by using blends of Diesel-Plastic liquid fuels. The plastic fuel is done with the pH test using pH meter after the purification process and brought to the normal by adding KOH and NaOH. Blends of 0 to 100% plastic liquid fuel-diesel mixture have been tested for performance and emission aspect as well. The experimental results shows the efficiently convert weight of municipal waste plastics into 65% of useful liquid hydrocarbon fuels without emitting much pollutants.

  4. Separation of polycarbonate and acrylonitrile-butadiene-styrene waste plastics by froth flotation combined with ammonia pretreatment.

    Science.gov (United States)

    Wang, Chong-Qing; Wang, Hui; Liu, Qun; Fu, Jian-Gang; Liu, You-Nian

    2014-12-01

    The objective of this research is flotation separation of polycarbonate (PC) and acrylonitrile-butadiene-styrene (ABS) waste plastics combined with ammonia pretreatment. The PC and ABS plastics show similar hydrophobicity, and ammonia treatment changes selectively floatability of PC plastic while ABS is insensitive to ammonia treatment. The contact angle measurement indicates the dropping of flotation recovery of PC is ascribed to a decline of contact angle. X-ray photoelectron spectroscopy demonstrates reactions occur on PC surface, which makes PC surface more hydrophilic. Separation of PC and ABS waste plastics was conducted based on the flotation behavior of single plastic. At different temperatures, PC and ABS mixtures were separated efficiently through froth flotation with ammonia pretreatment for different time (13 min at 23 °C, 18 min at 18 °C and 30 min at 23 °C). For both PC and ABS, the purity and recovery is more than 95.31% and 95.35%, respectively; the purity of PC and ABS is up to 99.72% and 99.23%, respectively. PC and ABS mixtures with different particle sizes were separated effectively, implying that ammonia treatment possesses superior applicability. Copyright © 2014 Elsevier Ltd. All rights reserved.

  5. Genotoxic effects of fumes from asphalt modified with waste plastic and tall oil pitch.

    Science.gov (United States)

    Lindberg, Hanna K; Väänänen, Virpi; Järventaus, Hilkka; Suhonen, Satu; Nygren, Jonas; Hämeilä, Mervi; Valtonen, Jarkko; Heikkilä, Pirjo; Norppa, Hannu

    2008-05-31

    As the use of recycled materials and industrial by-products in asphalt mixtures is increasing, we investigated if recycled additives modify the genotoxicity of fumes emitted from asphalt. Fumes were generated in the laboratory at paving temperature from stone-mastic asphalt (SMA) and from SMA modified with waste plastic (90% polyethylene, 10% polypropylene) and tall oil pitch (SMA-WPT). In addition, fumes from SMA, SMA-WPT, asphalt concrete (AC), and AC modified with waste plastic and tall oil pitch (AC-WPT) were collected at paving sites. The genotoxicity of the fumes was studied by analysis of DNA damage (measured in the comet assay) and micronucleus formation in human bronchial epithelial BEAS 2B cells in vitro and by counting mutations in Salmonella typhimurium strains TA98 and YG1024. DNA damage was also assessed in buccal leukocytes from road pavers before and after working with SMA, SMA-WPT, AC, and AC-WPT. The chemical composition of the emissions was analysed by gas chromatography/mass spectrometry. The SMA-WPT fume generated in the laboratory induced a clear increase in DNA damage in BEAS 2B cells without metabolic activation. The laboratory-generated SMA fume increased the frequency of micronucleated BEAS 2B cells without metabolic activation. None of the asphalt fumes collected at the paving sites produced DNA damage with or without metabolic activation. Fumes from SMA and SMA-WPT from the paving sites increased micronucleus frequency without metabolic activation. None of the asphalt fumes studied showed mutagenic activity in Salmonella. No statistically significant differences in DNA damage in buccal leukocytes were detected between the pre- and post-shift samples collected from the road pavers. However, a positive correlation was found between DNA damage and the urinary metabolites of polycyclic aromatic hydrocarbons (PAHs) after work shift, which suggested an association between occupational exposures during road paving and genotoxic effects. Our

  6. A New Life for Cross-Linked Plastic Waste as Aggregates and Binder Modifier for Asphalt Mixtures

    Directory of Open Access Journals (Sweden)

    Liliana M. B. Costa

    2017-06-01

    Full Text Available Every year, millions of tons of plastic waste, with potential to be reused, are wasted in landfills. Based on a literature review and in a local market analysis, cross-linked polyethylene (PEX waste arose as the material with the greatest potential to be tested for incorporation in asphalt mixtures due to the difficulty in its recycling and the lack of solutions for its reuse. Thus, in the present work, mixtures produced with and without PEX were tested in order to compare their performance, aiming at understanding if this waste could successfully be used as an alternative material for this type of application. Thus, water sensitivity, rutting resistance, stiffness modulus and fatigue cracking resistance tests were carried out on asphalt mixtures with up to 5% PEX. Based on the results obtained, it can be concluded that the incorporation of PEX in asphalt mixtures is a viable solution for paving works, especially when high service temperatures are expected. It also decreases the density of the mixture, which can be attractive to lighten structures. Thus, this technology contributes to give new life to cross-linked polyethylene plastic waste.

  7. Techno-economic analysis of a food waste valorization process via microalgae cultivation and co-production of plasticizer, lactic acid and animal feed from algal biomass and food waste.

    Science.gov (United States)

    Kwan, Tsz Him; Pleissner, Daniel; Lau, Kin Yan; Venus, Joachim; Pommeret, Aude; Lin, Carol Sze Ki

    2015-12-01

    A techno-economic study of food waste valorization via fungal hydrolysis, microalgae cultivation and production of plasticizer, lactic acid and animal feed was simulated and evaluated by Super-Pro Designer®. A pilot-scale plant was designed with a capacity of 1 metric ton day(-1) of food waste with 20 years lifetime. Two scenarios were proposed with different products: Scenario (I) plasticizer & lactic acid, Scenario (II) plasticizer & animal feed. It was found that only Scenario I was economically feasible. The annual net profits, net present value, payback period and internal rate of return were US$ 422,699, US$ 3,028,000, 7.56 years and 18.98%, respectively. Scenario II was not economic viable due to a deficit of US$ 42,632 per year. Sensitivity analysis showed that the price of lactic acid was the largest determinant of the profitability in Scenario I, while the impact of the variables was very close in Scenario II.

  8. Recycling of Plastic

    DEFF Research Database (Denmark)

    Christensen, Thomas Højlund; Fruergaard, Thilde

    2011-01-01

    Plastic is produced from fossil oil. Plastic is used for many different products. Some plastic products like, for example, wrapping foil, bags and disposable containers for food and beverage have very short lifetimes and thus constitute a major fraction of most waste. Other plastic products like......, good strength and long durability. Recycling of plastic waste from production is well-established, while recycling of postconsumer plastic waste still is in its infancy. This chapter describes briefly how plastic is produced and how waste plastic is recycled in the industry. Quality requirements...

  9. Study of the co-pyrolysis of biomass and plastic wastes

    Energy Technology Data Exchange (ETDEWEB)

    Paradela, Filipe; Pinto, Filomena; Gulyurtlu, Ibrahim; Cabrita, Isabel [INETI-DEECA, Lisbon (Portugal); Lapa, Nuno [UNL-FCT, GDEH-UBiA, Caparica (Portugal)

    2009-02-15

    This work aimed to study the recovery of two types of waste by the process of pyrolysis. The obtained results show that the adding of a plastic mix improves the overall efficiency of the slow pyrolysis of pine. Therefore, it was possible to achieve higher liquid yields and less solid product than in the classic slow pyrolysis carbonization of biomass. The obtained liquids showed heating values similar to that of heating fuel oil. The gas products had energetic contents superior to that of producer gas, and the obtained solid fractions showed heating values higher than some coals. There were also identified some typical products of fast biomass pyrolysis used as raw material in several industries. The effects of experimental conditions in product yield and composition were also studied. The parameters that showed higher influence were (with its increase): reaction time on gas product composition (increase of the alkane content) and on liquid composition (increase in aromatics content); reaction temperature on product yield (decrease of liquid yield with increase of solids and gases) and on gas product composition (increase in alkane content); initial pressure on liquid composition (increase in the aromatics content) and mainly the pine content of the initial mixture on products yield (increase of gas and solid yield with a decrease in liquids) and on the gas product composition (favouring CO and CO{sub 2} formation). (orig.)

  10. Study of combustion and emission characteristics of fuel derived from waste plastics by various waste to energy (W-t-E) conversion processes

    Science.gov (United States)

    Hazrat, M. A.; Rasul, M. G.; Khan, M. M. K.

    2016-07-01

    Reduction of plastic wastes by means of producing energy can be treated as a good investment in the waste management and recycling sectors. In this article, conversion of plastics into liquid fuel by two thermo-chemical processes, pyrolysis and gasification, are reviewed. The study showed that the catalytic pyrolysis of homogenous waste plastics produces better quality and higher quantity of liquefied fuel than that of non-catalytic pyrolysis process at a lower operating temperature. The syngas produced from gasification process, which occurs at higher temperature than the pyrolysis process, can be converted into diesel by the Fischer-Tropsch (FT) reaction process. Conducive bed material like Olivine in the gasification conversion process can remarkably reduce the production of tar. The waste plastics pyrolysis oil showed brake thermal efficiency (BTE) of about 27.75%, brake specific fuel consumption (BSFC) of 0.292 kg/kWh, unburned hydrocarbon emission (uHC) of 91 ppm and NOx emission of 904 ppm in comparison with the diesel for BTE of 28%, BSFC of 0.276 kg/kWh, uHC of 57 ppm and NOx of 855 ppm. Dissolution of Polystyrene (PS) into biodiesel also showed the potential of producing alternative transport fuel. It has been found from the literature that at higher engine speed, increased EPS (Expanded Polystyrene) quantity based biodiesel blends reduces CO, CO2, NOx and smoke emission. EPS-biodiesel fuel blend increases the brake thermal efficiency by 7.8%, specific fuel consumption (SFC) by 7.2% and reduces brake power (Pb) by 3.2%. More study using PS and EPS with other thermoplastics is needed to produce liquid fuel by dissolving them into biodiesel and to assess their suitability as a transport fuel. Furthermore, investigation to find out most suitable W-t-E process for effective recycling of the waste plastics as fuel for internal combustion engines is necessary to reduce environmental pollution and generate revenue which will be addressed in this article.

  11. RECYCLING BLENDS OF WASTE PLASTICS AND BIOMASS AS REDUCING AGENT FOR THE PRODUCTION OF METALLIC IRON FROM IRON OXIDE

    Directory of Open Access Journals (Sweden)

    JAMES RANSFORD DANKWAH

    2013-12-01

    Full Text Available Laboratory studies on the production of metallic iron from iron oxide using blends of palm nut shells (Elaes Guineanses and waste plastics as reducing agent have been performed through experiments conducted in a horizontal tube furnace. Composite pellets were formed from mixtures of iron oxide and carbonaceous materials consisting of chars of palm nut shells (PNS, high density polyethylene (HDPE and two blends of PNS with HDPE. Two sources of iron oxide were utilised in this investigation; reagent grade iron oxide (96.89 % Fe2O3 and EAF slag (47.1 % FeO. The iron oxide-carbonaceous material composites were heated rapidly at 1500°C in a continuous stream of argon and the off gas was analysed continuously using an infrared (IR gas analyser and a gas chromatographic (GC analyser. Elemental analyses of samples of the reduced metal were performed chemically for its carbon and oxygen contents using a LECO carbon/sulphur and oxygen/nitrogen analysers, respectively. The extent of reduction (after ten and fifteen minutes for reagent grade iron oxide and EAF slag, respectively and the level of carburisation were determined for each carbonaceous reductant. The results indicate that carburised metallic iron can be produced effectively from iron oxide using PNS, HDPE and blends of these carbonaceous materials as reductants. The extent of reduction improved significantly when PNS was blended with HDPE.

  12. Genetic Determinism vs. Phenotypic Plasticity in Protist Morphology.

    Science.gov (United States)

    Mulot, Matthieu; Marcisz, Katarzyna; Grandgirard, Lara; Lara, Enrique; Kosakyan, Anush; Robroek, Bjorn J M; Lamentowicz, Mariusz; Payne, Richard J; Mitchell, Edward A D

    2017-02-23

    Untangling the relationships between morphology and phylogeny is key to building a reliable taxonomy, but is especially challenging for protists, where the existence of cryptic or pseudocryptic species makes finding relevant discriminant traits difficult. Here we use Hyalosphenia papilio (a testate amoeba) as a model species to investigate the contribution of phylogeny and phenotypic plasticity in its morphology. We study the response of H. papilio morphology (shape and pores number) to environmental variables in (i) a manipulative experiment with controlled conditions (water level), (ii) an observational study of a within-site natural ecological gradient (water level), and (iii) an observational study across 37 European peatlands (climate). We showed that H. papilio morphology is correlated to environmental conditions (climate and water depth) as well as geography, while no relationship between morphology and phylogeny was brought to light. The relative contribution of genetic inheritance and phenotypic plasticity in shaping morphology varies depending on the taxonomic group and the trait under consideration. Thus, our data call for a reassessment of taxonomy based on morphology alone. This clearly calls for a substantial increase in taxonomic research on these globally still under-studied organisms leading to a reassessment of estimates of global microbial eukaryotic diversity.

  13. Production of an alternative fuel by the co-pyrolysis of landfill recovered plastic wastes and used lubrication oils.

    Science.gov (United States)

    Breyer, Sacha; Mekhitarian, Loucine; Rimez, Bart; Haut, B

    2017-02-01

    This work is a preliminary study for the development of a co-pyrolysis process of plastic wastes excavated from a landfill and used lubrication oils, with the aim to produce an alternative liquid fuel for industrial use. First, thermogravimetric experiments were carried out with pure plastics (HDPE, LDPE, PP and PS) and oils (a motor oil and a mixture of used lubrication oils) in order to highlight the interactions occurring between a plastic and an oil during their co-pyrolysis. It appears that the main decomposition event of each component takes place at higher temperatures when the components are mixed than when they are alone, possibly because the two components stabilize each other during their co-pyrolysis. These interactions depend on the nature of the plastic and the oil. In addition, co-pyrolysis experiments were led in a lab-scale reactor using a mixture of excavated plastic wastes and used lubrication oils. On the one hand, the influence of some key operating parameters on the outcome of the process was analyzed. It was possible to produce an alternative fuel for industrial use whose viscosity is lower than 1Pas at 90°C, from a plastic/oil mixture with an initial plastic mass fraction between 40% and 60%, by proceeding at a maximum temperature included in the range 350-400°C. On the other hand, the amount of energy required to successfully co-pyrolyze, in lab conditions, 1kg of plastic/oil mixture with an initial plastic mass fraction of 60% was estimated at about 8MJ. That amount of energy is largely used for the thermal cracking of the molecules. It is also shown that, per kg of mixture introduced in the lab reactor, 29MJ can be recovered from the combustion of the liquid resulting from the co-pyrolysis. Hence, this co-pyrolysis process could be economically viable, provided heat losses are addressed carefully when designing an industrial reactor. Copyright © 2016 Elsevier Ltd. All rights reserved.

  14. Global Reverse Supply Chain Redesign for Household Plastic Waste under the Emission Trading Scheme

    NARCIS (Netherlands)

    Bing, X.; Bloemhof-Ruwaard, J.M.; Chabaane, A.; Vorst, van der J.G.A.J.

    2015-01-01

    With increasing global resource scarcity, waste becomes a resource that can be managed globally. A reverse supply chain network for waste recycling needs to process all the waste with minimum costs and environmental impact. As re-processing of waste is one of the major sources of pollution in the

  15. Global Reverse Supply Chain Redesign for Household Plastic Waste under the Emission Trading Scheme

    NARCIS (Netherlands)

    Bing, X.; Bloemhof-Ruwaard, J.M.; Chabaane, A.; Vorst, van der J.G.A.J.

    2015-01-01

    With increasing global resource scarcity, waste becomes a resource that can be managed globally. A reverse supply chain network for waste recycling needs to process all the waste with minimum costs and environmental impact. As re-processing of waste is one of the major sources of pollution in the re

  16. NASA 50 amp hour nickel cadmium battery waste heat determination

    Science.gov (United States)

    Mueller, V. C.

    1980-01-01

    A process for determining the waste heat generated in a 50-ampere-hour, nickel cadmium battery as a function of the discharge rate is described and results are discussed. The technique involved is essentially calibration of the battery as a heat transfer rate calorimeter. The tests are run at three different levels of battery activity, one at 40-watts of waste heat generated, one at 60, and one at 100. Battery inefficiency ranges from 14 to 18 percent at discharge rates of 284 to 588 watts, respectively and top-of-cell temperatures of 20 C.

  17. Near-infrared imaging spectroscopy (NIRIS) and image rank analysis for remote identification of plastics in mixed waste.

    Science.gov (United States)

    Wienke, D; Van Den Broek, W; Melssen, W; Buydens, L; Feldhoff, R; Huth-Fehre, T; Kantimm, T; Winter, F; Cammann, K

    1996-03-01

    An infrared camera with focal plane InSb array detector has been applied to the characterization of macroscopic samples of household waste over distances up to two meters. Per waste sample (singelized), a sequence of images was taken at six optical wavelength ranges in the near infrared region (1100 nm - 2500 nm). The obtained three-dimensional data stack served as individual fingerprint per sample. An abstract factor rotation of this stack of six images into a spectroscopical meaningful intermediate six-element vector by Multivariate Image Rank Analysis (MIRA) finally provided a decision limit for the discrimination of plastics and nonplastics. A correct classification of better than 80% has been reached. The experimental NIRIS set-up has been automated so far to allow an on-line identification of a real world waste sample within a few seconds.

  18. A modified method for COD determination of solid waste, using a commercial COD kit and an adapted disposable weighing support.

    Science.gov (United States)

    André, L; Pauss, A; Ribeiro, T

    2017-03-01

    The chemical oxygen demand (COD) is an essential parameter in waste management, particularly when monitoring wet anaerobic digestion processes. An adapted method to determine COD was developed for solid waste (total solids >15%). This method used commercial COD tubes and did not require sample dilution. A homemade plastic weighing support was used to transfer the solid sample into COD tubes. Potassium hydrogen phthalate and glucose used as standards showed an excellent repeatability. A small underestimation of the theoretical COD value (standard values around 5% lower than theoretical values) was also observed, mainly due to the intrinsic COD of the weighing support and to measurement uncertainties. The adapted COD method was tested using various solid wastes in the range of 1-8 mgCOD, determining the COD of dried and ground cellulose, cattle manure, straw and a mixed-substrate sample. This new adapted method could be used to monitor and design dry anaerobic digestion processes.

  19. Conversion of waste plastics to single-cell protein by means of pyrolysis followed by fermentation

    Energy Technology Data Exchange (ETDEWEB)

    Karlhigesan, J.; Brown, B.S.

    Waste plastics (e.g. polyethylene, polystyrene and polypropylene) have been converted to single-cell protein using pyrolysis followed by fermentation. Conversion efficiencies of plastics to pyrolysate were 75-90% for polyethylene, 10-56% for polystyrene and 40-50% for polypropylene. Unpyrolyzed residues were formed with polystyrene (6-14%) and polypropylene (14-30%), but not with polyethylene. Polyvinyl chloride produced hydrogen chloride fumes, together with 33-39% unpyrolyzed residue, no fermentable pyrolysis products being formed. Polyethylene pyrolysate was fermented by the yeast, Candida tropicalis. Batch fermentation was carried out at 31 degrees Centigrade and pH 5.5 on polyethylene pyrolysate in shaken flasks (100 cubic centimetre culture) and in an aerated fermenter (500 cubic centimetre culture). Maximum growth rate was 0.168/hour, cell yield was 0.47 plus or minus 0.02 g g/1 pyrolysate used (n equals 3) and doubling time was 4-5 hours, after 72 hours growth on 1.0 g pyrolysate 100 centimetres-3 culture. Continuous culture (dilution rate 0.10/hour) gave a dry cell yield of 0.39 g/g pyrolysate utilized. Utilization of pyrolysate was 49.0% in batch culture and 33.0% in continuous culture. The efficiency of conversion to polyethylene to biomass was 34-42% in batch culture. Emulsification and pristane-solubilization were studied as a means of dispersing waxy pyrolysates in culture media. Pristane did not support growth whereas the emulsifier (lecithin, Tween 85 and sodium glycocholate (1:2:2 by weight)) could support up to 27% of the growth observed on polyethylene pyrolysate. Crude protein content of cells cultured on polyethylene pyrolysate was 46.7 plus or minus 2.4% (n equals 3) for batch culture cells, and 43.8 plus or minus 0.3% (n equals 4) for continuous culture cells. The true protein content of Candida cells was about 17%. The protein had a favourable nutritional quality as judged by in-vitro chemical tests.

  20. Determination of 36Cl in nuclear waste from reactor decommissioning

    DEFF Research Database (Denmark)

    Hou, Xiaolin; Frøsig, Lars; Nielsen, Sven Poul

    2007-01-01

    An analytical method for the determination of Cl-36 in nuclear waste such as graphite, heavy concrete, steel, aluminum, and lead was developed. Several methods were investigated for decomposing the samples. AgCl precipitation was used to separate Cl-36 from the matrix elements, followed by ion...... of this analytical method for Cl-36 is 14 mBq. The method has been used to determine Cl-36 in heavy concrete, aluminum, and graphite from the Danish DR-2 research reactor....

  1. Characteristics of Waste Plastics Pyrolytic Oil and Its Applications as Alternative Fuel on Four Cylinder Diesel Engines

    Directory of Open Access Journals (Sweden)

    Nosal Nugroho Pratama

    2014-02-01

    Full Text Available Waste plastics recycling using pyrolysis method is not only able to decrease a number of environment pollutant but also able to produce economical and high quality hydrocarbon products. Two experiments were conducted to completely study Waste Plastic Pyrolytic Oil (WPPO characteristics and its applications.  First experiment investigated oil characteristics derived from pyrolysis process in two stages batch reactors: pyrolysis and catalytic reforming reactor, at maximum temperature 500oC and 450oC respectively. Waste Polyethylene (PE, Polypropylene (PP, Polystyrene (PS, Polyethylene Terepthalate (PET and others were used as raw material. Nitrogen flow rate at 0.8 l/minutes was used to increase oil weight percentage. Indonesian natural zeolite was used as catalyst. Then, second experiment was carried out on Diesel Engine Test Bed (DETB used blending of WPPO and Biodiesel fuel with a volume ratio of 1:9. This experiment was specifically conducted to study how much potency of blending of WPPO and biodiesel in diesel engine. The result of first experiment showed that the highest weight percentage of WPPO derived from mixture of PE waste (50%wt, PP waste (40%wt and PS waste (10%wt is 45.13%wt. The more weight percentage of PE in feedstock effected on the less weight percentage of WPPO, the more percentage of C12-C20 content in WPPO and the higher calorific value of WPPO. Characteristics of WPPO such as, Specific Gravity, Flash point, Pour Point, Kinematic Viscosity, Calorific value and percentage of C12-C20 showed interesting result that WPPO could be developed as alternative fuel on diesel fuel blending due to the proximity of their characteristics. Performance of diesel engine using blending of WPPO and biodiesel on second experiment gave good result so the WPPO will have great potency to be valuable alternative liquid fuel in future, especially on stationary diesel engine and transportation engine application.

  2. A Perspective on the Prowaste Concept: Efficient Utilization of Plastic Waste through Product Design and Process Innovation

    Directory of Open Access Journals (Sweden)

    Antonio Greco

    2014-07-01

    Full Text Available This work is aimed to present an innovative technology for the reinforcement of beams for urban furniture, produced by in-mold extrusion of plastics from solid urban waste. This material, which is usually referred to as “recycled plastic lumber”, is characterized by very poor mechanical properties, which results in high deflections under flexural loads, particularly under creep conditions. The Prowaste project, founded by the EACI (European Agency for Competitiveness and Innovation in the framework of the Eco-Innovation measure, was finalized to develop an innovative technology for selective reinforcement of recycled plastic lumber. Selective reinforcement was carried out by the addition of pultruded glass rods in specific positions with respect to the cross section of the beam, which allowed optimizing the reinforcing efficiency. The reinforcement of the plastic lumber beams with pultruded rods was tested at industrial scale plant, at Solteco SL (Alfaro, Spain. The beams obtained, characterized by low cost and weight, were commercialized by the Spanish company. The present paper presents the most relevant results of the Prowaste project. Initially, an evaluation of the different materials candidates for the reinforcement of recycled plastic lumber is presented. Plastic lumber beams produced in the industrial plant were characterized in terms of flexural properties. The results obtained are interpreted by means of beam theory, which allows for extrapolation of the characteristic features of beams produced by different reinforcing elements. Finally, a theoretical comparison with other approaches which can be used for the reinforcement of plastic lumber is presented, highlighting that, among others, the Prowaste concept maximizes the stiffening efficiency, allowing to significantly reduce the weight of the components.

  3. Road pavers' occupational exposure to asphalt containing waste plastic and tall oil pitch.

    Science.gov (United States)

    Väänänen, Virpi; Elovaara, Eivor; Nykyri, Erkki; Santonen, Tiina; Heikkilä, Pirjo

    2006-01-01

    Waste plastic (WP) and tall oil pitch (T), which are organic recycled industrial by-products, have been used as a binder with bitumen in stone mastic asphalt (SMA) and asphalt concrete (AC). We compared the exposure over one workday in 16 road pavers participating in a survey at four paving sites, using mixes of conventional asphalt (SMA, AC) or mixes containing waste material (SMA-WPT, AC-WPT). The concentrations of 11 aldehydes in air were 515 and 902 microg m(-3) at the SMA-WPT and AC-WPT worksites, being 3 and 13 times greater than at the corresponding worksites laying conventional asphalt. Resin acids (2-42 microg m(-3)), which are known sensitizers, were detected only during laying of AC-WPT. The emission levels (microg m(-3)) of total particulates (300-500), bitumen fumes (60-160), bitumen vapour (80-1120), naphthalene (0.59-1.2), phenanthrene (0.21-0.32), pyrene (<0.015-0.20), benzo(a)pyrene (<0.01) and the sum of 16 PAHs (polycyclic aromatic hydrocarbons, 1.28-2.00) were similar for conventional and WPT asphalts. The dermal deposition of 16 PAHs on exposure pads (on workers' wrist) was low in all pavers (0.7-3.5 ng cm(-2)). Eight OH-PAH biomarkers of naphthalene, phenanthrene and pyrene exposures were quantified in pre- and post-shift urine specimens. The post-shift concentrations (mean +/- SD, micromol mol(-1) creatinine) of 1- plus 2-naphthol; 1-,2-,3-,4- plus 9-phenanthrol; and 1-hydroxypyrene were, respectively, for asphalt workers: 18.1+/- 8.0, 2.41 +/- 0.71 and 0.66+/- 0.58 (smokers); 6.0+/- 2.3, 1.70+/- 0.72 and 0.27+/- 0.15 (non-smokers); WPT asphalt workers: 22.0+/- 9.2, 2.82+/- 1.11 and 0.76+/- 0.18 (smokers); 6.8+/- 2.6, 2.35+/- 0.69 and 0.46+/- 0.13 (non-smokers). The work-related uptake of PAHs was low in all pavers, although it was significantly greater in smokers than in non-smokers. The WPT asphalt workers complained of eye irritation and sore throat more than the pavers who had a much lower exposure to aldehydes and resin acids.

  4. Specific heat and thermal conductivity of explosives, mixtures, and plastic-bonded explosives determined experimentally

    Energy Technology Data Exchange (ETDEWEB)

    Baytos, J.F.

    1979-09-01

    The specific heat and thermal conductivity of explosives and plastic-bonded explosives of interest to WX operations, determined experimentally, are reported in three tables. Specific heat was determined by differential scanning calorimetry against sapphire standards. Thermal conductivity was determined by two means: the guarded hot-plate method or the differential scanning calorimeter comparative method on miniature samples.

  5. Application of WLS strips for position determination in Strip PET tomograph based on plastic scintillators

    CERN Document Server

    Smyrski, J; Bednarski, T; Białas, P; Czerwiński, E; Kapłon, Ł; Kochanowski, A; Korcyl, G; Kowal, J; Kowalski, P; Kozik, T; Krzemień, W; Molenda, M; Niedźwiecki, Sz; Pałka, M; Pawlik, M; Raczyński, L; Rudy, Z; Salabura, P; Sharma, N G; Silarski, M; Słomski, A; Strzelecki, A; Wiślicki, W; Zieliński, M; Zoń, N

    2013-01-01

    A method of determination of a gamma quantum absorption point in a plastic scintillator block using a matrix of wavelength-shifting (WLS) strips is proposed. Application of this method for improvement of position resolution in newly proposed PET detectors based on plastic scintillators is presented. The method enables to reduce parallax errors in reconstruction of images which occurs in the presently used Positron Emission Tomography scanners.

  6. Co-pyrolysis of hydrothermally upgraded brown coal and wax prepared from waste plastics

    Energy Technology Data Exchange (ETDEWEB)

    Kouichi Miura; Susan A. Roces; Monthicha Pattatapanusak; Hiroyuki Nakagawa; Ryuichi Ashida; Masato Morimoto [Kyoto University, Kyoto (Japan). Department of Chemical Engineering

    2007-07-01

    We have recently presented a hydrothermal extraction method that not only removes water from brown coal but also upgrades the coal and extracts low molecular mass compounds simultaneously. The upgraded coal contained much less oxygen than the raw coal. However, it still needs to be further upgraded to be utilized as a substitute for bituminous coal. In this study co-pyrolysis of the upgraded coals and waxes formed from waste plastics was investigated for this purpose. Waxes were prepared through pyrolysis of polyethylene, polypropylene, and polyethylene terephtalate. Upgraded coals were then impregnated with the waxes in an autoclave at 200{sup o}C under pressure. The mixtures of coal and wax were rapidly heated up to 1040{sup o}C at about 3000{sup o}C/s using a Curie point pyrolyzer in an inert atmosphere. The char yield was greatly enhanced by a factor of 1.1 to 1.3 compared to the char yield obtained when the upgraded coals and waxes were pyrolyzed independently. Even under a slower heating rate (0.17{sup o}C/s) the char yields increased by a factor of 1.2 for the all mixtures of the upgraded coal and waxes. Since no such effect was found when the raw brown coal was impregnated with waxes, it was suggested that the modification of the structure of brown coal by the hydrothermal extraction could enhance interactions between the coal and the wax when co-pyrolyzed. Effect of wax mixing ratio on co-pyrolysis behavior was also examined. The char yield dramatically increased when the ratio exceeded about 0.3 g/g for the pyrolysis of both under slow and rapid heating rates. This trend coincided with that of the swelling ratio of the upgraded coal impregnated with wax, indicating that some physical change by wax-impregnation affected the co-pyrolysis behavior. 5 refs., 14 figs., 3 tabs.

  7. Analytical methods for the determination of DEHP plasticizer alternatives present in medical devices: a review.

    Science.gov (United States)

    Bernard, L; Décaudin, B; Lecoeur, M; Richard, D; Bourdeaux, D; Cueff, R; Sautou, V

    2014-11-01

    Until 2010, diethylhexylphthalate (DEHP) was the plasticizer most commonly used to soften PVC medical devices (MDs), because of a good efficiency/cost ratio. In flexible plasticized PVC, phthalates are not chemically bound to PVC and they are released into the environment and thus may come into contact with patients. The European Directive 2007/47/CE, classified DEHP as a product with a toxicity risk and restricted its use in MDs. MD manufacturers were therefore forced to quickly find alternatives to DEHP to maintain the elasticity of PVC nutrition tubings, infusion sets and hemodialysis lines. Several replacement plasticizers, so-called "alternative to DEHP plasticizers" were incorporated into the MDs. Nowadays, the risk of exposure to these compounds for hospitalized patients, particularly in situations classified "at risk", has not yet been evaluated, because migrations studies, providing sufficient exposure and human toxicity data have not been performed. To assess the risk to patients of DEHP plasticizer alternatives, reliable analytical methods must be first developed in order to generate data that supports clinical studies being conducted in this area. After a brief introduction of the characteristics and toxicity of the selected plasticizers used currently in MDs, this review outlines recently analytical methods available to determine and quantify these plasticizers in several matrices, allowing the evaluation of potential risk and so risk management.

  8. Recycling of engineering plastics from waste electrical and electronic equipments: influence of virgin polycarbonate and impact modifier on the final performance of blends.

    Science.gov (United States)

    Ramesh, V; Biswal, Manoranjan; Mohanty, Smita; Nayak, Sanjay K

    2014-05-01

    This study is focused on the recovery and recycling of plastics waste, primarily polycarbonate, poly(acrylonitrile-butadiene-styrene) and high impact polystyrene, from end-of-life waste electrical and electronic equipments. Recycling of used polycarbonate, acrylonitrile-butadiene-styrene, polycarbonate/acrylonitrile-butadiene-styrene and acrylonitrile-butadiene-styrene/high impact polystrene material was carried out using material recycling through a melt blending process. An optimized blend composition was formulated to achieve desired properties from different plastics present in the waste electrical and electronic equipments. The toughness of blended plastics was improved with the addition of 10 wt% of virgin polycarbonate and impact modifier (ethylene-acrylic ester-glycidyl methacrylate). The mechanical, thermal, dynamic-mechanical and morphological properties of recycled blend were investigated. Improved properties of blended plastics indicate better miscibility in the presence of a compatibilizer suitable for high-end application.

  9. Application of biotests for the determination of soil ecotoxicity after exposure to biodegradable plastics

    Directory of Open Access Journals (Sweden)

    Susanna Sforzini

    2016-10-01

    Full Text Available Biodegradable plastics are mostly applied in packaging materials (e.g. shopping bags, waste collection bags, catering products, and agricultural applications. In this last case, degradation takes place directly in soil where biodegradable plastic products are intentionally left after use (e.g. mulch films for weeds control. Due to the growing volumes of biodegradable polymers and plastics, interest in their environmental safety is increasing and more research is carried out. Some attempt has been made to apply biotests, used in other sectors of environmental sciences, in the assessment of biodegradable plastics safety. In this work, the quality of soils after biodegradation of the bioplastics Mater-Bi has been assessed with a large array of biotests based on model organisms representative of the different trophic levels in the food chains of the edaphic and aquatic ecosystems. Mater-Bi was degraded under controlled conditions for 6 months at a 1% concentration. The selected organisms included bacteria and protozoa (V. fischeri and D. discoideum, respectively, the green alga P. subcapitata, plants (the monocotyledon S. saccharatum and the dicotyledon L. sativum, and invertebrates animals (D. magna, a freshwater crustacean, and the Oligochaeta earthworm E. andrei, using both acute and chronic endpoints. The results of the applied ecotoxicological tests showed that the Mater-Bi materials tested at very high doses did not affect the soil quality. Soil exposed to Mater-Bi has no noxious effects on edaphic organisms; in particular, mono and dicotyledon plants results, indicate that Mater-Bi plastic products are innocuous for agricultural uses. The use of more sensitive chronic endpoints allows to exclude possible effects at population level. This is the first time that such a comprehensive approach is applied to the assessment of possible ecotoxicity effects induced by biodegradable plastics in soil and represents a possible starting point for

  10. Polybrominated diphenyl ethers (PBDEs) in China: policies and recommendations for sound management of plastics from electronic wastes.

    Science.gov (United States)

    Ni, Kun; Lu, Yonglong; Wang, Tieyu; Shi, Yajuan; Kannan, Kurunthachalam; Xu, Li; Li, Qiushuang; Liu, Shijie

    2013-01-30

    Polybrominated diphenyl ethers (PBDEs), used as flame retardants (BFRs), are incorporated in plastics of most electronic equipment. Among BFR mixtures, deca-BDE is the most widely used commercial additive in the polymer industry and the use of deca-BDE is currently not subject to any restrictions in China. However, debate over environmental and health risks associated with deca-BDE still remains. Regulatory agencies in developed countries have adopted and/or established environmentally sound strategies for the management of potential threat posed by PBDEs to the environment and human health. No regulations or management policies for PBDEs currently exist in China at either central or provincial government levels. Large amounts of plastics containing PBDEs are still in use and must be disposed of after their lifetimes, creating outdoor reservoirs for the future dispersal of PBDEs into the environment. Concerted action is needed not only to regulate the production and use of PBDEs but also to find ways to effectively manage waste electrical and electronic products that contain PBDEs. This article is the first to investigate the policy issues and current problems related to the use of PBDEs in China. In addition, we estimate the mass flows of PBDEs contained in Waste Electrical and Electronic Equipment (WEEE) in China. We suggest alternatives to PBDEs and sound management of plastics used in electrical and electronic equipment (EEE) that contain PBDEs.

  11. Draft EEC method for the determination of the global migration of plastics constituents into fatty-food simulants: Applicability to lacquers, plastics and laminates

    NARCIS (Netherlands)

    Battum, D. van; Rijk, M.A.H.; Verspoor, R.; Rossi, L.

    1982-01-01

    An experimental study was carried out to establish whether the draft EEC method for the determination of the global migration of constituents from plastics packaging materials into fatty food stimulants could be applied to all plastics, including lacquers and laminates. Some difficulties were

  12. Hybrid selective surface hydrophilization and froth flotation separation of hazardous chlorinated plastics from E-waste with novel nanoscale metallic calcium composite.

    Science.gov (United States)

    Mallampati, Srinivasa Reddy; Heo, Je Haeng; Park, Min Hee

    2016-04-05

    Treatment by a nanometallic Ca/CaO composite has been found to selectively hydrophilize the surface of polyvinyl chloride (PVC), enhancing its wettability and thereby promoting its separation from E-waste plastics by means of froth flotation. The treatment considerably decreased the water contact angle of PVC, by about 18°. The SEM images of the PVC plastic after treatment displayed significant changes in their surface morphology compared to other plastics. The SEM-EDS results reveal that a markedly decrease of [Cl] concentration simultaneously with dramatic increase of [O] on the surface of the PCV samples. XPS results further confirmed an increase of hydrophilic functional groups on the PVC surface. Froth flotation at 100rpm mixing speed was found to be optimal, separating 100% of the PVC into a settled fraction of 96.4% purity even when the plastics fed into the reactor were of nonuniform size and shape. The total recovery of PVC-free plastics in E-waste reached nearly 100% in the floated fraction, significantly improved from the 20.5wt% of light plastics that can be recovered by means of conventional wet gravity separation. The hybrid method of nanometallic Ca/CaO treatment and froth flotation is effective in the separation of hazardous chlorinated plastics from E-waste plastics. Copyright © 2015 Elsevier B.V. All rights reserved.

  13. Experimental investigation of the quality characteristics of agricultural plastic wastes regarding their recycling and energy recovery potential.

    Science.gov (United States)

    Briassoulis, D; Hiskakis, M; Babou, E; Antiohos, S K; Papadi, C

    2012-06-01

    A holistic environmentally sound waste management scheme that transforms agricultural plastic waste (APW) streams into labelled guaranteed quality commodities freely traded in open market has been developed by the European research project LabelAgriWaste. The APW quality is defined by the APW material requirements, translated to technical specifications, for recycling or energy recovery. The present work investigates the characteristics of the APW quality and the key factors affecting it from the introduction of the virgin product to the market to the APW stream reaching the disposer. Samples of APW from different countries were traced from their application to the field through their storage phase and transportation to the final destination. The test results showed that the majority of APW retained their mechanical properties after their use preserving a "very good quality" for recycling in terms of degradation. The degree of soil contamination concerning the APW recycling and energy recovery potential fluctuates depending on the agricultural plastic category and application. The chlorine and heavy metal content of the tested APW materials was much lower than the maximum acceptable limits for their potential use in cement industries.

  14. The use KPI's to determine the waste in production process

    Science.gov (United States)

    Borsos, G.; Iacob, C. C.; Calefariu, G.

    2016-11-01

    In theory and practice of management is well-known Lean approach about forms of waste from production processes (Muda) and the method VSM (Value Stream Map), one of the most effective methods for determining the activities generating value within industrial companies. It is also obvious concern of the specialists for performance measurement regardless of purview of the organizations. The literature review has shown that the link between performance indicators and the objectives of the companies is researched in detail. However, the correlation between indicators and the forms of waste that generate deviations from the setpoints is rather nature practical and it depends on the talent and managerial skills of those directing production processes. The paper presents the results of a applied study, performed by the authors, through which it was has sought to will create a system of performance indicators specific to manufacturing activity that to be a useful tool to quantify the losses and to determining ways to improve default losses.

  15. Determination of acceptable risk criteria for nuclear waste management

    Energy Technology Data Exchange (ETDEWEB)

    Cohen, J.J.

    1977-10-21

    The initial phase of the work performed during FY 1977 consisted of performing a ''scoping'' study to define issues, determine an optimal methodology for their resolution, and compile a data base for acceptable risk criteria development. The issues, spanning technical, psychological, and ethical dimensions, were categorized in seven major areas: (1) unplanned or accidental events, (2) present vs future risks, (3) institutional controls and retrievability, (4) dose-response mechanism and uncertainty, (5) spatial distribution of exposed populations, (6) different types of nuclear wastes, and (7) public perception. The optimum methodology for developing ARC was determined to be multi-attribute decision analysis encompassing numerous specific techniques for choosing, from among several alternatives, the optimal course of action when the alternatives are constrained to meet specified attributes. The data base developed during the study comprises existing regulations and guidelines, maximum permissible dose, natural geologic hazards, nonradioactive hazardous waste practices, bioethical perspectives, and data from an opinion survey.

  16. Solvent extraction as additional purification method for postconsumer plastic packaging waste

    NARCIS (Netherlands)

    Thoden van Velzen, E.U.; Jansen, M.

    2011-01-01

    An existing solvent extraction process currently used to convert lightly polluted post-industrial packaging waste into high quality re-granulates was tested under laboratory conditions with highly polluted post-consumer packaging waste originating from municipal solid refuse waste. The objective was

  17. Solvent extraction as additional purification method for postconsumer plastic packaging waste

    NARCIS (Netherlands)

    Thoden van Velzen, E.U.; Jansen, M.

    2011-01-01

    An existing solvent extraction process currently used to convert lightly polluted post-industrial packaging waste into high quality re-granulates was tested under laboratory conditions with highly polluted post-consumer packaging waste originating from municipal solid refuse waste. The objective was

  18. The effect of glycerol from biodiesel production waste as a plasticizer on physical character edible film of chitosan

    Science.gov (United States)

    Rosyid, Fajar Abdul; Triastuti, Rr. Juni; Andriyono, Sapto

    2017-02-01

    Chitosan edible film is a thin layer of clear packaging made from chitosan edible and biodegradable. Edible chitosan films are stiffer and less elastic, so it should be added plasticizer glycerol. One source of glycerol is inexpensive and easily obtained is crude glycerol from biodiesel production. The purpose of this study was to determine the effect of various concentrations of crude glycerol plasticizer on the physical characteristics of chitosan edible film and determine the best concentration of crude glycerol plasticizer. This study used a completely randomized design (CRD) with five treatments and four replications. The Edible film using the g chitosan and some plasticizers concentration of crude glycerol (0.2, 0.4, 0.8, and 1 mL) and a control treatment that used 0.4 mL of pure glycerol was made. The results showed that the use of crude glycerol plasticizer had effect to the physical character of chitosan edible film. Increasing concentrations of crude glycerol plasticizer exhibits the lowers value of the thickness and tensile strength, however, can increase the value of percent elongation. The best concentration of this research is the treatment of B (0.2 ml crude glycerol) which resulted in 0.55 mm thickness, the tensile strength of 95.38 kgf/cm2 and a percent elongation of 2.13%.

  19. ACTIVITY TEST AND REGENERATION OF NiMo/Z CATALYST FOR HYDROCRACKING OF WASTE PLASTIC FRACTION TO GASOLINE FRACTION

    Directory of Open Access Journals (Sweden)

    Rodiansono Rodiansono

    2010-06-01

    Full Text Available Activity test and regeneration of NiMo/active natural zeolite catalyst for hydrocracking of waste plastic fraction of polyprophylene (PP type have been carried out. The catalysts was prepared by loading Mo followed by Ni Metals onto the natural zeolite (Z sample, then calcined at 500oC, oxidized and reduced at 400oC under nitrogen, oxygen and hydrogen stream, respectively. The characterization of catalysts including spesific surface area, average pore radius, and total pore volume were performed by gas sorption analyzer, amount of total acid sites was determined by gas sorption method, and acid site strength was confirmed by IR spectroscopy. The hydrocracking process was carried out in a semi-flow reactor system at 360 oC and catalyst:feed ratio 0.5 under hydrogen stream (150 mL/hour. The feed was vaporized from the pyrolisis reactor into the hydrocracking reactor. A liquid product was collected and analyzed by gas chromatography (GC and gas chromatography-mass spectroscopy (GC-MS. The characterization results showed that spesific surface area, average pore radius, and total pore volume of the Z sample decreased after loading of the Ni and Mo metals. Amount of total acid sites of the NiMo/Z catalyst was higher than that of the Z sample. The activity of NiMo/Z catalyst decreased after several continously runs. Its regeneration produced the NiMo/Z reg catalyst with similar activity and selectivity to the fresh catalyst (NiMo/Z. The activity of catalysts at the optimum condition followed the order of NiMo/Z reg>NiMo/Z>Z (conversion of hydrocarbon C>12 and NiMo/Z reg>NiMo/Z>Z (total yield of gasoline fraction. The selectivity of catalysts for C7-C8 product followed the order of Z>NiMo/Z>NiMo/Z reg. Keywords: activity, polyprophylene, catalyst, gasoline fraction.

  20. Polímeros biodegradáveis - uma solução parcial para diminuir a quantidade dos resíduos plásticos Biodegradable polymers - a partial way for decreasing the amount of plastic waste

    Directory of Open Access Journals (Sweden)

    Sandra Mara Martins Franchetti

    2006-07-01

    Full Text Available The large use of plastics has generated a waste deposit problem. Today plastic wastes represent 20% in volume of the total waste in the municipal landfills. To solve the disposal problem of plastics methods have been employed such as incineration, recycling, landfill disposal, biodegradation and the use of biodegradable polymers. Incineration of plastic wastes provokes pollution due to the production of poisonous gases. Recycling is important to reduce final costs of plastic materials, but is not enough in face of the amount of discarded plastic. In landfills plastic wastes remain undegraded for a long time, causing space and pollution problems. Biodegradation is a feasible method to treat some plastics, but intensive research is necessary to find conditions for the action of microorganisms. All of these methods are important and the practical application of each one depends on the type and amount of the plastic wastes and the environmental conditions. Therefore, a great deal of research has focused on developing biodegradable plastics and its application because it is an important way for minimizing the effect of the large volume of plastic waste discarded in the world.

  1. How to prepare a road map for the management of plastic waste

    DEFF Research Database (Denmark)

    Dorland, Jens; Jørgensen, Michael Søgaard; Skovgaard, Mette

    This paper presents the results of Plastic Zero with the hope to inspire further action to enhance plastic resource-efficiency. It is meant as a source of inspiration on how to make a road map in a similar project. The process has given us various experiences and this guideline on how to make...

  2. How to prepare a road map for the management of plastic waste

    DEFF Research Database (Denmark)

    Dorland, Jens; Jørgensen, Michael Søgaard; Skovgaard, Mette

    This paper presents the results of Plastic Zero with the hope to inspire further action to enhance plastic resource-efficiency. It is meant as a source of inspiration on how to make a road map in a similar project. The process has given us various experiences and this guideline on how to make...

  3. Learning about the Types of Plastic Wastes: Effectiveness of Inquiry Learning Strategies

    Science.gov (United States)

    So, Wing-Mui Winnie; Cheng, Nga-Yee Irene; Chow, Cheuk-Fai; Zhan, Ying

    2016-01-01

    This study aims to examine the impacts of the inquiry learning strategies employed in a "Plastic Education Project" on primary students' knowledge, beliefs and intended behaviour in Hong Kong. Student questionnaires and a test on plastic types were adopted for data collection. Results reveal that the inquiry learning strategies…

  4. Efficient conversion of polyamides to ω-hydroxyalkanoic acids: a new method for chemical recycling of waste plastics.

    Science.gov (United States)

    Kamimura, Akio; Ikeda, Kosuke; Suzuki, Shuzo; Kato, Kazunari; Akinari, Yugo; Sugimoto, Tsunemi; Kashiwagi, Kohichi; Kaiso, Kouji; Matsumoto, Hiroshi; Yoshimoto, Makoto

    2014-09-01

    An efficient transformation of polyamides to ω-hydroxy alkanoic acids was achieved. Treatment of nylon-12 with supercritical MeOH in the presence of glycolic acid gave methyl ω-hydroxydodecanoate in 85% yield and the alcohol/alkene selectivity in the product was enhanced to up to 9.5:1. The use of (18)O-enriched acetic acid for the reaction successfully introduced an (18)O atom at the alcoholic OH group in the product. This strategy may provide a new and economical solution for the chemical recycling of waste plastics.

  5. UTILIZING WASTE PLASTIC POLYPROPYLENE AND POLYETHYLENE TEREPHTHALATE AS ALTERNATIVE AGGREGATES TO PRODUCE LIGHTWEIGHT CONCRETE: A REVIEW

    Directory of Open Access Journals (Sweden)

    IBRAHIM H. ALFAHDAWI

    2016-08-01

    Full Text Available In recent times, there is an increasing need for the fabrication of mortar and concrete that can be characterised as sustainable and environmentally friendly. Ideally, this concrete should be inexpensive, lightweight, and outstanding in terms of its physical and mechanical specifications. Plastic materials have increasingly been used in the fabrication of different types of concrete admixtures and mortar constituents. These plastic materials take the form of fillers or shredded fibres derived from polypropylene and polyethylene terephthalate. The use of plastic materials presents the following benefits: (i enhanced mixture quality and (ii a reduction in the amount of accumulated single-use plastic materials that negatively impact the environment. This work reviews several previous studies on the utilisation and preparations of plastic materials and their effects on the physical and mechanical properties of concrete. Other topics, including hardened concrete, fresh concrete, application, and thermo-physical characteristics, are also elaborated.

  6. Apparent plasticity in functional traits determining competitive ability and spatial distribution: a case from desert.

    Science.gov (United States)

    Xie, Jiang-Bo; Xu, Gui-Qing; Jenerette, G Darrel; Bai, Yong-fei; Wang, Zhong-Yuan; Li, Yan

    2015-07-20

    Species competitive abilities and their distributions are closely related to functional traits such as biomass allocation patterns. When we consider how nutrient supply affects competitive abilities, quantifying the apparent and true plasticity in functional traits is important because the allometric relationships among traits are universal in plants. We propose to integrate the notion of allometry and the classical reaction norm into a composite theoretical framework that quantifies the apparent and true plasticity. Combining the framework with a meta-analysis, a series of field surveys and a competition experiment, we aimed to determine the causes of the dune/interdune distribution patterns of two Haloxylon species in the Gurbantonggut Desert. We found that (1) the biomass allocation patterns of both Haloxylon species in responses to environmental conditions were apparent rather than true plasticity and (2) the allometric allocation patterns affected the plants' competition for soil nutrient supply. A key implication of our results is that the apparent plasticity in functional traits of plants determines their response to environmental change. Without identifying the apparent and true plasticity, we would substantially overestimate the magnitude, duration and even the direction of plant responses in functional traits to climate change.

  7. Recycling of Plastic

    DEFF Research Database (Denmark)

    Christensen, Thomas Højlund; Fruergaard, Thilde

    2011-01-01

    Plastic is produced from fossil oil. Plastic is used for many different products. Some plastic products like, for example, wrapping foil, bags and disposable containers for food and beverage have very short lifetimes and thus constitute a major fraction of most waste. Other plastic products like......, for example, gutters, window frames, car parts and transportation boxes have long lifetimes and thus appear as waste only many years after they have been introduced on the market. Plastic is constantly being used for new products because of its attractive material properties: relatively cheap, easy to form......, good strength and long durability. Recycling of plastic waste from production is well-established, while recycling of postconsumer plastic waste still is in its infancy. This chapter describes briefly how plastic is produced and how waste plastic is recycled in the industry. Quality requirements...

  8. Substitution potentials of recycled HDPE and wood particles from post-consumer packaging waste in Wood-Plastic Composites.

    Science.gov (United States)

    Sommerhuber, Philipp F; Welling, Johannes; Krause, Andreas

    2015-12-01

    The market share of Wood-Plastic Composites (WPC) is small but expected to grow sharply in Europe. This raises some concerns about suitable wood particles needed in the wood-based panels industry in Europe. Concerns are stimulated by the competition between the promotion of wooden products through the European Bioeconomy Strategy and wood as an energy carrier through the Renewable Energy Directive. Cascade use of resources and valorisation of waste are potential strategies to overcome resource scarcity. Under experimental design conditions, WPC made from post-consumer recycled wood and plastic (HDPE) were compared to WPC made from virgin resources. Wood content in the polymer matrix was raised in two steps from 0% to 30% and 60%. Mechanical and physical properties and colour differences were characterized. The feasibility of using cascaded resources for WPC is discussed. Results indicate the technical and economic feasibility of using recycled HDPE from packaging waste for WPC. Based on technical properties, 30% recycled wood content for WPC is feasible, but economic and political barriers of efficient cascading of biomass need to be overcome.

  9. Improving Public Health and Environment through Plastic Waste Management in Mumbai Metropolitan Region

    OpenAIRE

    Rode, Sanjay

    2015-01-01

    The Mumbai Metropolitan Region is growing in terms of population, industry, educational and commercial units. The daily requirements of commodities and services by all units have increased fast. Plastic is used extensively for packing, protection and service of various commodities. The use of plastic is much higher by industry and households in region. In Brihan Mumbai Municipal Corporation, the density of population is higher. The concentration of small and large industries is more. Therefor...

  10. Groundwater Quality Assessment for Waste Management Area U: First Determination

    Energy Technology Data Exchange (ETDEWEB)

    FN Hodges; CJ Chou

    2000-08-04

    Waste Management Area U (TWA U) is located in the 200 West Area of the Hanford Site. The area includes the U Tank Farm, which contains 16 single-shell tanks and their ancillary equipment and waste systems. WMA U is regulated under the Resource Conservation and Recovery Act of 1976 (RCRA) as stipulated in 40 CFR Part 265, Subpart F, which is incorporated into the Washington State dangerous waste regulations (WAC 173-303400) by reference. Groundwater monitoring at WMA U has been guided by an interim status indicator evaluation program. As a result of changes in the direction of groundwater flow, background values for the WMA have been recalculated several times during its monitoring history. The most recent recalculation revealed that one of the indicator parameters, specific conductance, exceeded its background value in downgradient well 299-W19-41. This triggered a change from detection monitoring to a groundwater quality assessment program. The major contributors to the higher specific conductance are nonhazardous constituents, such as bicarbonate, calcium, chloride, magnesium, sodium and sulfate. Chromium, nitrate, and technetium-99 are present and are increasing; however, they are significantly below their drinking water standards. The objective of this study is to determine whether the increased concentrations of chromium, nitrate, and technetium-99 in groundwater are from WMA U or from an upgradient source. Interpretation of groundwater monitoring data indicates that both the nonhazardous constituents causing elevated specific conductance in groundwater and the tank waste constituents present in groundwater at the WMA are a result of surface water infiltration in the southern portion of the WMA. There is evidence that both upgradient and WMA sources contribute to the nitrate concentrations that were detected. There is no indication of an upgradient source for the chromium and technetium-99 that was detected. Therefore, a source of contamination appears to

  11. ENVIRONMENTAL RESEARCH BRIEF: WASTE MINIMIZATION ASSESSMENT FOR A MANUFACTURER OF PRINTED PLASTIC BAGS

    Science.gov (United States)

    The U.S. Environmental Protection Agency (EPA) has funded a pilot project to assist small- and medium-size manufacturers who want to minimize their generation of hazardous waste but who lack the expertise to do so. Waste Minimization Assessment Centers (WMACs) were established ...

  12. Ionometric determination of chloride ion in circulating and waste waters

    Energy Technology Data Exchange (ETDEWEB)

    Bebeshko, G.I.; Afanas' eva, V.I.; Danielova, I.I.; Dmitriev, M.A.; Radchenko, A.F.

    1986-09-01

    The authors attempt to develop selective ionometric methods to determine chloride ion in waste and circulating waters from technological ore processing, containing significant amounts of sulfide ion and various flotation reagents. These waters contain practically no cations that form hard to dissolve compounds with chloride ion such as Ag/sup +/, Cu/sup +/, Hg/sup +/ or Pb/sup 2 +/. The chloride ion concentration in water varies between 10 and 100 mg/liter. Information is shown on the concentration of the main anions and flotation reagents in waters that were analyzed.

  13. 高炉喷吹废塑料的先进技术%Establishment of Advanced Recycling Technology for Waste Plastics in Blast Furnace

    Institute of Scientific and Technical Information of China (English)

    王颖

    2012-01-01

    废塑料循环利用技术对于全球环境保护和社会发展都是一个非常重要的课题。JFE制钢公司为了将废塑料作为高炉的还原剂,通过热模燃烧实验;研究了废塑料的燃烧气化率。经过研究,为了改善粗粒废塑料的燃烧性,开发了同时喷吹煤粉或/和天然气的技术,为了提高废塑料的燃烧和气化率及炉内透气性,JFE开发出将废塑料与碳酸钙(CaC03)复合造粒技术。另外,JFE还研究了废塑料精细粉碎技术。此技术已经应用在实际生产中。%The establishment of technology for recycling waste plastics is a highly important issue for global environmental conservation and the society. JFE Steel has pursued the effective use of waste plastics as a reducing agent for injection into blast furnaces, and conducted hot model experiments to study the combustion and gasification behaviour of waste plastics. On the basis of this basic investigation, advanced technologies that can further improve the combustion and gasification efficiency of waste plastics even with low strength has been developed; i.e. in order to improve combustibility of fine waste plastics, technology for simultaneous injection of such plastics with pulverized coal and/or natural gas has been developed. For improved the strength of plastics, technology for combined agglomeration of waste plastics with CaC03 has been developed. In addition, technology for fine crushing of waste plastics has been studied on the basis of new ideas, and this technology has been applied in actual plant operation. These technologies have been successfully applied in actual blast furnaces, contributing to lowering the reducing agent rate.

  14. Qualitative and quantitative determination of heavy metals in waste cellular phones.

    Science.gov (United States)

    Maragkos, Konstantinos G; Hahladakis, John N; Gidarakos, Evangelos

    2013-09-01

    Twenty four waste cellular phones, manufactured between 2002 and 2011, were selected in order to determine the total heavy metal content in each of their parts (printed circuit boards (PCBs), plastic housing (PH) and liquid crystal display monitors (LCDs)) and compare the results with the permissible limits set by the 2003 Directive on Restriction of Hazardous Substances (RoHS). All the selected samples were pulverized and digested with strong acids. Inductively coupled plasma-mass spectrometry was used to measure the heavy metal content in each sample. The results revealed that concentration levels of the examined heavy metals were higher in PCBs, followed by PH and LCD in that particular order (PCB>PH>LCD). With the exception of Pb and Cr present in PCBs of mobile phones released before the year 2006, all the other metal concentrations were according to the Directive. Concentration levels of Cd, Hg were lower than the permissible limits set by the EU, either before or after the validity of the 2003 RoHS Directive. Considering their significant heavy metal content, coupled with their large quantities produced worldwide in an annual rate, waste cellular phones need to be treated under an environmentally sound management scheme, prioritizing recycling and at the same time eliminating the possibility of any harm. Copyright © 2013 Elsevier Ltd. All rights reserved.

  15. Recycling of plastic wastes from electric and electronic sector new developments; Reciclado de residuos plasticos del sector electrico y electronico. Nuevos desarrollos

    Energy Technology Data Exchange (ETDEWEB)

    Miguel, R.; Larrauri, E.; Cacho, I.

    1999-07-01

    Automated technologies for the identification and sorting of plastic wastes have been developed to get an adequate and cost-effective recycling. When dealing with plastics from end-of-live electric and electronic equipment not only the polymeric matrix but also fillers and/or flame retardant additives and/or pigments, need to be taken in account. At present, several specific projects are being carried out by GAIKER in order to solve the technological challenge of recycling plastics from the electric and electronic sector. (Author)

  16. Solid-Phase Photocatalytic Degradation of Waste Plastics%固相光催化降解废弃塑料

    Institute of Scientific and Technical Information of China (English)

    杨昌军; 彭天右; 邓克俭; 昝菱

    2011-01-01

    White pollution has become a global environmental issue in recent years. Composite plastics embedding photocatalysts into ploymer matrix has excellent photocatalytic degradation activity. It could be degraded effectively in ambient air under sunlight exposure. So it is an eco-friendly disposal of polymer wastes, and provides a promising way to solve white pollution. In this paper, the latest research progress in solid-phase photocatalytic degradation of waste plastics is reviewed. The solid-phase photocatalytic activity of TiO2, ZnO, α-FeOOH and H3PW12O40, as well as the photocatalytic degradation mechanism of various composite plastics are introduced.Many new methods have been used to enhance the solid-phase photocatalytic degradation activity of composite plastics and the utilization efficiency of sunlight. For example, surface modifying photocatalyst by branched macromolecule is used to improve the dispersion of photocatalyst in polymer matrix, modifying photocatalyst by metal ion doping or dye sensitization is used to broaden the region of photoresponse and enhance the visible light activity of photocatalyst. At last, the potential application prospects for photodegradable composite plastics in the field of waste plastic treatment is discussed.%"白色污染"已成为目前普遍关注的一个全球性环保课题.将光催化剂掺入到塑料中制备出环境友好的可光降解复合塑料,利用其光催化活性可以使废弃塑料在太阳光的照射下发生有效降解,是解决"白色污染"问题的有效途径之一.本文综述了近年来固相光催化降解废弃塑料的研究进展,介绍了光催化剂TiO、ZnO、а-FeOOH和HPWO加对废弃塑料的固相光催化降解效率及各种复合塑料的光催化降解机理,阐述了对光催化剂进行表面改性可以改善其在聚合物中的分散性,以及对光催化剂进行修饰可以提高其对可见光的吸收,从而提高复合塑料的固相光催化降解活性及对

  17. Determination of 36Cl in nuclear waste from reactor decommissioning.

    Science.gov (United States)

    Hou, Xiaolin; Ostergaard, Lars Frøsig; Nielsen, Sven P

    2007-04-15

    An analytical method for the determination of 36Cl in nuclear waste such as graphite, heavy concrete, steel, aluminum, and lead was developed. Several methods were investigated for decomposing the samples. AgCl precipitation was used to separate 36Cl from the matrix elements, followed by ion-exchange chromatography to remove interfering radionuclides. The purified 36Cl was then measured by liquid scintillation counting. The chemical yield of chlorine, as measured by ICPMS, is above 70% and the decontamination factors for all interfering radionuclides are greater than 10(6). The detection limit of this analytical method for 36Cl is 14 mBq. The method has been used to determine 36Cl in heavy concrete, aluminum, and graphite from the Danish DR-2 research reactor.

  18. Commercial and Institutional Waste

    DEFF Research Database (Denmark)

    Christensen, Thomas Højlund; Fruergaard, Thilde

    2011-01-01

    is handled in the municipal waste system, where information is easily accessible. An important part of commercial and institutional waste is packaging waste, and enterprises with large quantities of clean paper, cardboard and plastic waste may have their own facilities for baling and storing their waste......Commercial and institutional waste is primarily from retail (stores), hotels, restaurants, health care (except health risk waste), banks, insurance companies, education, retirement homes, public services and transport. Within some of these sectors, e.g. retail and restaurants, large variations...... are found in terms of which products and services are offered. Available data on unit generation rates and material composition as well as determining factors are discussed in this chapter. The characterizing of commercial and institutional waste is faced with the problem that often only a part of the waste...

  19. Demonstration of sulfur solubility determinations in high waste loading, low-activity waste glasses

    Energy Technology Data Exchange (ETDEWEB)

    Fox, K. M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2016-04-25

    A method recommended by Pacific Northwest National Laboratory (PNNL) for sulfate solubility determinations in simulated low-activity waste glasses was demonstrated using three compositions from a recent Hanford high waste loading glass study. Sodium and sulfate concentrations in the glasses increased after each re-melting step. Visual observations of the glasses during the re-melting process reflected the changes in composition. The measured compositions showed that the glasses met the targeted values. The amount of SO3 retained in the glasses after washing was relatively high, ranging from 1.6 to 2.6 weight percent (wt %). Measured SnO2 concentrations were notably low in all of the study glasses. The composition of the wash solutions should be measured in future work to determine whether SnO2 is present with the excess sulfate washed from the glass. Increases in batch size and the amount of sodium sulfate added did not have a measureable impact on the amount of sulfate retained in the glass, although this was tested for only a single glass composition. A batch size of 250 g and a sodium sulfate addition targeting 7 wt %, as recommended by PNNL, will be used in future experiments.

  20. DMS cyclone separation processes for optimization of plastic wastes recycling and their implications.

    Science.gov (United States)

    Gent, Malcolm Richard; Menendez, Mario; Toraño, Javier; Torno, Susana

    2011-06-01

    It is demonstrated that substantial reductions in plastics presently disposed of in landfills can be achieved by cyclone density media separation (DMS). In comparison with the size fraction of plastics presently processed by industrial density separations (generally 6.4 to 9.5 mm), cyclone DMS methods are demonstrated to effectively process a substantially greater range of particle sizes (from 0.5 up to 120 mm). The purities of plastic products and recoveries obtained with a single stage separation using a cylindrical cyclone are shown to attain virtually 100% purity and recoveries >99% for high-density fractions and >98% purity and recoveries were obtained for low-density products. Four alternative schemas of multi-stage separations are presented and analyzed as proposed methods to obtain total low- and high-density plastics fraction recoveries while maintaining near 100% purities. The results of preliminary tests of two of these show that the potential for processing product purities and recoveries >99.98% of both density fractions are indicated. A preliminary economic comparison of capital costs of DMS systems suggests cyclone DMS methods to be comparable with other DMS processes even if the high volume capacity for recycling operations of these is not optimized.

  1. Final Regulatory Determination for Special Wastes From Mineral Processing (Mining Waste Exclusion) - Federal Register Notice, June 13, 1991

    Science.gov (United States)

    This action presents the Agency's final regulatory determination required by section 3001(b)(3)(C) of the Resource Conservation and Recovery Act (RCRA) for 20 special wastes from the processing of ores and minerals.

  2. Difficulties Regarding Determination of Plasticity Index of Silty Soils by use of Casagrande and Fall Cone Methods

    DEFF Research Database (Denmark)

    Poulsen, Rikke; Ibsen, Lars Bo; Nielsen, Benjaminn Nordahl

    2012-01-01

    Soil plasticity index and thereby the liquid limit and plastic limit are often used in order to classify the soil type and determine soil properties. Generally, two methods, i.e. the Casagrande cup method and the fall cone method are adopted in order to determine the liquid limit of soil. In many...... or high plasticity. In addition, critics of the fall cone method indicate that the liquid limit can be determined by the fall cone even though it is not possible with the Casagrande cup which is why the soil should be noted as non-plastic. This paper presents how the Casagrande cup method is inapplicable...... countries, the fall cone is the preferred method to determine the liquid limit due to simplicity and comparative reproducibility. However, some researchers state that the liquid limit obtained by using the fall cone method cannot represent the soil plasticity particularly in soil with either very low...

  3. Plastics wastes as secondary fuel in a cement plant; Residuos plasticos como combustible secundario en una cementera

    Energy Technology Data Exchange (ETDEWEB)

    Miguel, R.; Irasarri, L.; Arnaiz, S.; Cacho, I.

    2000-07-01

    The use of secondary fuel derived from plastics wastes from municipal source has been tested in an industrial cement plant. The recovered materials have been conditioned in order to fulfill the texture, composition and energetic requirements of the cement kiln. The performed long-term trials have shown the stability of the industrial facility during the operation with this alternative fuels. Several controls carried out over gaseous emissions confirmed the absence of differences in the emitted pollutant levels when compared with normal operation. The quality of the obtained clinker, checked using the established standard measurements, was found identical to the one in a clinker prepared using conventional fuels. The LCA (Life Cycle Analysis) tool was applied to evaluate a series of environmental impacts and proved that the energetic valorization alternative is more favourable then the disposal practice. Finally, a positive economical balance reinforced the option of energy recovery previously supported by favourable technical and environmental considerations. (Author) 16 refs.

  4. Occurrence mode and concentration of chlorine in liquid product from co-pyrolysis of waste plastic and coal

    Energy Technology Data Exchange (ETDEWEB)

    Li Zhen; Liu Ze-chang; Zhou Li-xia [Chemical and Environmental Department of Taishan College, Taian (China)

    2009-08-15

    The occurrence mode and concentration of chlorine in liquid product including tar and water from co-pyrolysis of waste plastic (WP) and coal were studied. The effect of temperature, holding time, heating rate and gas flow on chlorine concentration in the liquid product was examined. The result indicates that the addition of WP to coal in co-pyrolysis does not increase the organic chlorine compound in the liquid product. However, the tar yield increases, and the water yield decreases. The chlorine in water mainly exists as inorganic form (NH{sub 4}Cl) and organic amine hydrochloride. There is no obvious C-Cl band in IR spectra of tar is observed. This indicates that the organic chlorine in tar is very little. 10 refs., 6 figs., 2 tabs.

  5. Morphological characteristics of waste polyethylene/polypropylene plastics during pyrolysis and representative morphological signal characterizing pyrolysis stages.

    Science.gov (United States)

    Wang, H; Chen, D; Yuan, G; Ma, X; Dai, X

    2013-02-01

    In this work, the morphological characteristics of waste polyethylene (PE)/polypropylene (PP) plastics during their pyrolysis process were investigated, and based on their basic image changing patterns representative morphological signals describing the pyrolysis stages were obtained. PE and PP granules and films were used as typical plastics for testing, and influence of impurities was also investigated. During pyrolysis experiments, photographs of the testing samples were taken sequentially with a high-speed infrared camera, and the quantitative parameters that describe the morphological characteristics of these photographs were explored using the "Image Pro Plus (v6.3)" digital image processing software. The experimental results showed that plastics pyrolysis involved four stages: melting, two stages of decomposition which are characterized with bubble formation caused by volatile evaporating, and ash deposition; and each stage was characterized with its own phase changing behaviors and morphological features. Two stages of decomposition are the key step of pyrolysis since they took up half or more of the reaction time; melting step consumed another half of reaction time in experiments when raw materials were heated up from ambient temperatures; and coke-like deposition appeared as a result of decomposition completion. Two morphological signals defined from digital image processing, namely, pixel area of the interested reaction region and bubble ratio (BR) caused by volatile evaporating were found to change regularly with pyrolysis stages. In particular, for all experimental scenarios with plastics films and granules, the BR curves always exhibited a slowly drop as melting started and then a sharp increase followed by a deep decrease corresponding to the first stage of intense decomposition, afterwards a second increase - drop section corresponding to the second stage of decomposition appeared. As ash deposition happened, the BR dropped to zero or very low

  6. Thermal and catalytic pyrolysis of a mixture of plastics from small waste electrical and electronic equipment (WEEE).

    Science.gov (United States)

    Santella, Chiara; Cafiero, Lorenzo; De Angelis, Doina; La Marca, Floriana; Tuffi, Riccardo; Vecchio Ciprioti, Stefano

    2016-08-01

    Pyrolysis seems a promising route for recycling of heterogeneous, contaminated and additives containing plastics from waste electrical and electronic equipment (WEEE). This study deals with the thermal and catalytic pyrolysis of a synthetic mixture containing real waste plastics, representative of polymers contained in small WEEE. Two zeolite-based catalysts were used at 400°C: HUSY and HZSM-5 with a high silica content, while three different temperatures were adopted for the thermal cracking: 400, 600 and 800°C. The mass balance showed that the oil produced by pyrolysis is always the main product regardless the process conditions selected, with yields ranging from 83% to 93%. A higher yield was obtained when pyrolysis was carried out with HZSM-5 at 400°C and without catalysts, but at 600 and 800°C. Formation of a significant amount of solid residue (about 13%) is observed using HUSY. The oily liquid product of pyrolysis, analysed by GC-MS and GC-FID, as well as by elemental analysis and for energy content, appeared lighter, less viscous and with a higher concentration of monoaromatics under catalytic condition, if compared to the liquid product derived from thermal degradation at the same temperature. HZSM-5 led to the production of a high yield of styrene (17.5%), while HUSY favoured the formation of ethylbenzene (15%). Energy released by combustion of the oil was around 39MJ/kg, thus suggesting the possibility to exploit it as a fuel, if the recovery of chemical compounds could not be realised. Elemental and proximate analysis of char and GC-TCD analysis of the gas were also performed. Finally, it was estimated to what extent these two products, showing a relevant ability to release energy, could fulfil the energy demand requested in pyrolysis.

  7. Determination of the Rate of Formation of Hydroceramic Waste Forms made with INEEL Calcined Wastes

    Energy Technology Data Exchange (ETDEWEB)

    Barry Scheetz; Johnson Olanrewaju

    2001-10-15

    The formulation, synthesis, characterization and hydration kinetics of hydroceramic waste forms designed as potential hosts for existing INEEL calcine high-level wastes have been established as functions of temperature and processing time. Initial experimentations were conducted with several aluminosilicate pozzolanic materials, ranging from fly ash obtained from various power generating coal and other combustion industries to reactive alumina, natural clays and ground bottled glass powders. The final selection criteria were based on the ease of processing, excellent physical properties and chemical durability (low-leaching) determined from the PCT test produced in hydroceramic. The formulation contains vermiculite, Sr(NO32), CsC1, NaOH, thermally altered (calcined natural clay) and INEEL simulated calcine high-level nuclear wastes and 30 weight percent of fluorinel blend calcine and zirconia calcine. Syntheses were carried out at 75-200 degree C at autogeneous water pressure (100% relative humidity) at various time intervals. The resulting monolithic compact products were hard and resisted breaking when dropped from a 5 ft height. Hydroceramic host mixed with fluorinel blend calcine and processed at 75 degree C crumbled into rice hull-side grains or developed scaly flakes. However, the samples equally possessed the same chemical durability as their unbroken counterparts. Phase identification by XRD revealed that hydroceramic host crystallized type zeolite at 75-150 degree C and NaP1 at 175-200 degree C in addition to the presence of quartz phase originating from the clay reactant. Hydroceramic host mixed with either fluorinel blend calcine or zirconia calcine crystallized type A zeolite at 75-95 degree C, formed a mixture of type A zeolite and hydroxysodalite at 125-150 degree C and hydroxysodalite at 175-200 degree C. Quartz, calcium fluoride and zirconia phases from the clay reactant and the two calcine wastes were also detected. The PCT test solution

  8. Task 3 -- Pyrolysis of plastic waste. Semi-annual report, April 1--September 30, 1997

    Energy Technology Data Exchange (ETDEWEB)

    Ness, R.O.; Aulich, T.R.

    1997-09-01

    The Energy and Environmental Research Center is developing a technology for the thermal decomposition of high-organic-content, radionuclide-contaminated mixed wastes and spent (radioactive) ion-exchange resins from the nuclear power industry that will enable the separation and concentration of radionuclides as dry particulate solids and the generation of nonradioactive condensable and noncondensable gas products. Successful application of the technology will enable a significant volume reduction of radioactive waste and the production of an inexpensively disposable nonradioactive organic product. The project objective is to develop and demonstrate the commercial viability of a continuous thermal decomposition process that can fulfill the following requirements: separate radionuclides from radioactive waste streams containing a variety of types and levels of polymers, chlorinated species, and other organics, including rubber, oils, resins, and cellulosic-based materials; concentrate radionuclides in a homogeneous, dry particulate product that can be recovered, handled, and disposed of efficiently and safely; separate and recover any chlorine present (as PVC, chlorinated solvents, or inorganic chlorine) in the contaminated mixed-waste stream; and yield a nonradioactive, low-chlorine-content, condensable organic product that can be economically disposed. Progress is described.

  9. Hazardous Waste Code Determinations for the First/Second Stage Sludge Waste Stream (IDCs 001, 002, 800)

    Energy Technology Data Exchange (ETDEWEB)

    Arbon, Rodney Edward

    2001-01-01

    This document, Hazardous Waste Code Determination for the First/Second-Stage Sludge Waste Stream, summarizes the efforts performed at the Idaho National Engineering and Environmental Laboratory (INEEL) to make a hazardous waste code determination on Item Description Codes (IDCs) 001, 002, and 800 drums. This characterization effort included a thorough review of acceptable knowledge (AK), physical characterization, waste form sampling, chemical analyses, and headspace gas data. This effort included an assessment of pre-Waste Analysis Plan (WAP) solidified sampling and analysis data (referred to as preliminary data). Seventy-five First/Second-Stage Sludge Drums, provided in Table 1-1, have been subjected to core sampling and analysis using the requirements defined in the Quality Assurance Program Plan (QAPP). Based on WAP defined statistical reduction, of preliminary data, a sample size of five was calculated. That is, five additional drums should be core sampled and analyzed. A total of seven drums were sampled, analyzed, and validated in compliance with the WAP criteria. The pre-WAP data (taken under the QAPP) correlated very well with the WAP compliant drum data. As a result, no additional sampling is required. Based upon the information summarized in this document, an accurate hazardous waste determination has been made for the First/Second-Stage Sludge Waste Stream.

  10. Separating and Recycling Plastic, Glass, and Gallium from Waste Solar Cell Modules by Nitrogen Pyrolysis and Vacuum Decomposition.

    Science.gov (United States)

    Zhang, Lingen; Xu, Zhenming

    2016-09-06

    Many countries have gained benefits through the solar cells industry due to its high efficiency and nonpolluting power generation associated with solar energy. Accordingly, the market of solar cell modules is expanding rapidly in recent decade. However, how to environmentally friendly and effectively recycle waste solar cell modules is seldom concerned. Based on nitrogen pyrolysis and vacuum decomposition, this work can successfully recycle useful organic components, glass, and gallium from solar cell modules. The results were summarized as follows: (i) nitrogen pyrolysis process can effectively decompose plastic. Organic conversion rate approached 100% in the condition of 773 K, 30 min, and 0.5 L/min N2 flow rate. But, it should be noted that pyrolysis temperature should not exceed 773 K, and harmful products would be increased with the increasing of temperature, such as benzene and its derivatives by GC-MS measurement; (ii) separation principle, products analysis, and optimization of vacuum decomposition were discussed. Gallium can be well recycled under temperature of 1123 K, system pressure of 1 Pa and reaction time of 40 min. This technology is quite significant in accordance with the "Reduce, Reuse, and Recycle Principle" for solid waste, and provides an opportunity for sustainable development of photovoltaic industry.

  11. Elevational differences in developmental plasticity determine phenological responses of grasshoppers to recent climate warming.

    Science.gov (United States)

    Buckley, Lauren B; Nufio, César R; Kirk, Evan M; Kingsolver, Joel G

    2015-06-22

    Annual species may increase reproduction by increasing adult body size through extended development, but risk being unable to complete development in seasonally limited environments. Synthetic reviews indicate that most, but not all, species have responded to recent climate warming by advancing the seasonal timing of adult emergence or reproduction. Here, we show that 50 years of climate change have delayed development in high-elevation, season-limited grasshopper populations, but advanced development in populations at lower elevations. Developmental delays are most pronounced for early-season species, which might benefit most from delaying development when released from seasonal time constraints. Rearing experiments confirm that population, elevation and temperature interact to determine development time. Population differences in developmental plasticity may account for variability in phenological shifts among adults. An integrated consideration of the full life cycle that considers local adaptation and plasticity may be essential for understanding and predicting responses to climate change.

  12. Elevational differences in developmental plasticity determine phenological responses of grasshoppers to recent climate warming

    Science.gov (United States)

    Buckley, Lauren B.; Nufio, César R.; Kirk, Evan M.; Kingsolver, Joel G.

    2015-01-01

    Annual species may increase reproduction by increasing adult body size through extended development, but risk being unable to complete development in seasonally limited environments. Synthetic reviews indicate that most, but not all, species have responded to recent climate warming by advancing the seasonal timing of adult emergence or reproduction. Here, we show that 50 years of climate change have delayed development in high-elevation, season-limited grasshopper populations, but advanced development in populations at lower elevations. Developmental delays are most pronounced for early-season species, which might benefit most from delaying development when released from seasonal time constraints. Rearing experiments confirm that population, elevation and temperature interact to determine development time. Population differences in developmental plasticity may account for variability in phenological shifts among adults. An integrated consideration of the full life cycle that considers local adaptation and plasticity may be essential for understanding and predicting responses to climate change. PMID:26041342

  13. Determination of mechanical properties of some glass fiber reinforced plastics suitable to Wind Turbine Blade construction

    Science.gov (United States)

    Steigmann, R.; Savin, A.; Goanta, V.; Barsanescu, P. D.; Leitoiu, B.; Iftimie, N.; Stanciu, M. D.; Curtu, I.

    2016-08-01

    The control of wind turbine's components is very rigorous, while the tower and gearbox have more possibility for revision and repairing, the rotor blades, once they are deteriorated, the defects can rapidly propagate, producing failure, and the damages can affect large regions around the wind turbine. This paper presents the test results, performed on glass fiber reinforced plastics (GFRP) suitable to construction of wind turbine blades (WTB). The Young modulus, shear modulus, Poisson's ratio, ultimate stress have been determined using tensile and shear tests. Using Dynamical Mechanical Analysis (DMA), the activation energy for transitions that appear in polyester matrix as well as the complex elastic modulus can be determined, function of temperature.

  14. Pengaruh Penambahan Kitosan dan Plasticizer Sorbitol terhadap Sifat Fisiko-Kimia Bioplastik dari Pati Biji Durian (Durio zibethinus)

    OpenAIRE

    Kristiani, Maria

    2016-01-01

    The application of plastics in large amount impact on environmental pollution caused by the buildup of plastic waste that can not be decomposed naturally (nonbiodegradable). Researches on bioplastics (biodegradable plastic) were conducted to find alternative reduction of the consumption of conventional plastics. The purposes of this study were to determine the characteristics of starch isolated from durian (Durio zibethinus) seed, to determine the effect of chitosan and plasticizer sorbitol o...

  15. Possibilities and limits of pyrolysis for recycling plastic rich waste streams rejected from phones recycling plants.

    Science.gov (United States)

    Caballero, B M; de Marco, I; Adrados, A; López-Urionabarrenechea, A; Solar, J; Gastelu, N

    2016-11-01

    The possibilities and limits of pyrolysis as a means of recycling plastic rich fractions derived from discarded phones have been studied. Two plastic rich samples (⩾80wt% plastics) derived from landline and mobile phones provided by a Spanish recycling company, have been pyrolysed under N2 in a 3.5dm(3) reactor at 500°C for 30min. The landline and mobile phones yielded 58 and 54.5wt% liquids, 16.7 and 12.6wt% gases and 28.3 and 32.4wt% solids respectively. The liquids were a complex mixture of organic products containing valuable chemicals (toluene, styrene, ethyl-benzene, etc.) and with high HHVs (34-38MJkg(-1)). The solids were composed of metals (mainly Cu, Zn, and Al) and char (≈50wt%). The gases consisted mainly of hydrocarbons and some CO, CO2 and H2. The halogens (Cl, Br) of the original samples were mainly distributed between the gases and solids. The metals and char can be easily separated and the formers may be recycled, but the uses of the char will be restricted due to its Cl/Br content. The gases may provide the energy requirements of the processing plant, but HBr and HCl must be firstly eliminated. The liquids could have a potential use as energy or chemicals source, but the practical implementation of these applications will be no exempt of great problems that may become insurmountable (difficulty of economically recovering pure chemicals, contamination by volatile metals, etc.).

  16. Wood plastic composites from agro-waste materials: Analysis of mechanical properties.

    Science.gov (United States)

    Nourbakhsh, Amir; Ashori, Alireza

    2010-04-01

    This article presents the application of agro-waste materials (i.e., corn stalk, reed stalk, and oilseed stalk) in order to evaluate and compare their suitability as reinforcement for thermoplastics as an alternative to wood fibers. The effects of fiber loading and CaCO(3) content on the mechanical properties were also studied. Overall trend shows that with addition of agro-waste materials, tensile and flexural properties of the composites are significantly enhanced. Oilseed fibers showed superior mechanical properties due to their high aspect ratio and chemical characteristics. The order of increment in the mechanical properties of the composites is oilseed stalk >corn stalk>reed stalk at all fiber loadings. The tensile and flexural properties of the composite significantly decreased with increasing CaCO(3) content, due to the reduction of interface bond between the fiber and matrix. It can be concluded from this study that the used agro-waste materials are attractive reinforcements from the standpoint of their mechanical properties.

  17. Increased urinary 8-hydroxy-2'-deoxyguanosine levels in workers exposed to di-(2-ethylhexyl) phthalate in a waste plastic recycling site in China.

    Science.gov (United States)

    Wang, Qian; Wang, Li; Chen, Xi; Rao, Kai Min; Lu, Shao You; Ma, Sheng Tao; Jiang, Pu; Zheng, Dan; Xu, Shun Qing; Zheng, Hong Yan; Wang, Jian Shu; Yu, Zhi Qiang; Zhang, Rong; Tao, Yong; Yuan, Jing

    2011-07-01

    Di-(2-ethylhexyl) phthalate (DEHP) is a common plasticizer used in industrial and diverse consumer products. Animal studies indicate DEHP caused developmental, reproductive, and hepatic toxicities. However, human studies of the potential effects of DEHP are limited. The exposed site with a history of over 20 years of waste plastic recycling was located in Hunan Province, China. The reference site without known DEHP pollution source was about 50 km far away from the exposed site. In this study, 181 workers working in plastic waste recycling and 160 gender-age matched farmers were recruited. DEHP concentrations in water and cultivated soil samples, serum thyroid-stimulating hormone, malondialdehyde (MDA), superoxide dismutase (SOD), urinary 8-hydroxy-2'-deoxyguanosine (8-OHdG), and micronuclei frequency in human capillary blood lymphocytes were analyzed. Mean levels of DEHP were greater in environment at the recycling site than at reference site (industry wastewater for the exposed: 42.43 μg/l; well water: 14.20 vs. 0.79 μg/l, pond water: 135.68 vs. 0.37 μg/l, cultivated soil: 13.07 vs. 0.81 mg/kg, p waste plastic recycling was an independent risk factor for the increased urinary 8-OHdG levels in the male workers (p < 0.01). The occupational DEHP exposure might contribute to oxidative deoxyribonucleic acid damage in the male workers.

  18. Waste Plastics Recycling and Reuse Technology Situation and Development Trend in China%我国废旧塑料的资源再利用现状与发展趋势

    Institute of Scientific and Technical Information of China (English)

    张雪; 张承龙

    2014-01-01

    通过对当前我国废旧塑料资源再利用现状的研究,分析和对比了不同废旧塑料资源再利用方法的工艺和特点,并且对废旧塑料处理的发展趋势做出了预测。%Through the study of the current status of waste plastic recycling, the processes and characteristics of different methods of recycling waste plastics are analyzed and compared, and the development trend of waste plastics processing is forecast.

  19. Application of plastic trash sorting technology in separating waste plastic mulch films from impurities%塑料垃圾分选技术在废旧地膜与杂质分离中的应用研究进展

    Institute of Scientific and Technical Information of China (English)

    石鑫; 牛长河; 乔园园; 张海春; 王学农

    2016-01-01

    Plastic film mulching technique has been using widely in China because of it’s notable features such as raising temperature,inhibiting weed growth,promoting crop maturity and increasing production. A large number of used plastic mulch films which have not be recycled and accumulated in the soil year after year and results serious waste plastic mulch film pollution. Recycled waste plastic mulch films twined each other with other impurities and makes the mulch film utilization becomes difficult. Some recycled waste plastic mulch films has been stacked or burned on field ridge freely which leads secondary pollution.Thus, the waste plastic mulch film pollution problems should be cracked from it’s beginning.Agricultural waste plastic mulch film and impurities separation technology is key links during mechanized mulch films recycling and reusing. Waste plastic mulch film as a valuable renewable resource and be important part of plastic production which comes from waste plastic mulch film by separation process. Effective recycling and reusing of waste plastic mulch film can improve economic benefits and even what’s more is that it can decrease the secondary pollution probability which caused by improper waste plastic mulch film handling. Some documents shows that the thickness of plastic mulch film used in foreign countries is generally above 0.12mm which keep the tensile strength of plastic mulch film be good enough and promote the rolling recycling machine development.Waste plastic mulch film is clean and complete which recycled by rolling recycling machine and it can be reused directly.At present, there is no relevant report about technology and equipment for waste plastic mulch film separation at abroad.The thickness of the plastic mulch film used generally in China between 0.004-0.008mm which leads the tensile strength not good enough after harvesting season and can not be recycled by rolling way. The only way which can recycling waste plastic mulch film by

  20. Evaluation of engine performance, emissions, of a twin cylinder diesel engine fuelled with waste plastic oil and diesel blends with a fraction of methanol

    Directory of Open Access Journals (Sweden)

    Y. Tarun

    2014-03-01

    Full Text Available A comprehensive study on the methanol and waste plastic oil as an alternative fuel has been carried out. This report deals with the exhaust emission of waste plastic fuel on twin cylinder diesel engine. The objectives of this report are to analyse the fuel consumption and the emission characteristic of a twin cylinder diesel engine that are using waste plastic oil compared to usage of ordinary diesel that are available in the market. This report describes the setups and the procedures for the experiment which is to analyse the emission characteristics and fuel consumption of diesel engine due to usage of the both fuels. Detail studies about the experimental setup and components have been done before the experiment started. Data that are required for the analysis is observed from the experiments. Calculations and analysis have been done after all the required data needed for the thesis is obtained. The experiment used diesel engine with no load which means no load exerted on it. A four stroke Twin cylinder diesel engine was adopted to study the brake thermal efficiency, brake specific energy consumption, mechanical efficiency, brake power, volumetric efficiency, indicated thermal efficiency and emissions at full load with the fuel of fraction methanol in bio-diesel. In this study, the diesel engine was tested using methanol blended with bio-diesel at certain mixing ratios of (WPO: Diesel 20:80, 40:60 and 60:40 methanol to bio-diesel respectively. By the end of the report, the successful of the project have been started which is Kirloskar engine is able to run with waste plastic oil (WPO but the engine needs to run by using diesel fuel first, then followed by waste plastic oil and finished with diesel fuel as the last fuel usage before the engine turned off. The performance of the engine using blended fuel compared to the performance of engine with diesel fuel. Experimental results of blended fuel and diesel fuel are also compared.   Keywords

  1. Climate accounting for waste management, Phase I and II. Summary: Phase 1: Glass Packaging, Metal packaging, paper, cardboard, plastic and wet organic waste. Phase 2: Wood waste and residual waste from households; Klimaregnskap for avfallshaandtering, Fase I og II. Sammendrag: Fase 1: Glassemballasje, metallemballasje, papir, papp, plastemballasje og vaatorganisk avfall. Fase 2: Treavfall og restavfall fra husholdninger

    Energy Technology Data Exchange (ETDEWEB)

    Raadal, Hanne Lerche; Modahl, Ingunn Saur; Lyng, Kari-Anne

    2009-09-15

    Background. On the basis of an increased focus on emissions of greenhouse gases in general, Waste Norway wanted to prepare a climate accounting for waste management in Norway. Oestfoldforskning was engaged to undertake the project. The aim of the project has been to develop a model for the calculation of net greenhouse gas emissions from different waste types of waste glass containers, metal containers, paper, cardboard, plastic, wet organic waste, wood waste and residual waste. The model is based on life cycle methodology and is used to calculate the net greenhouse gas emissions per kg of waste for the various waste management options and waste types, as well as to calculate the net greenhouse gas emissions for waste management for including waste types and quantities of 2006. There is an emphasis on developing a model so that municipalities / waste companies or regions can develop their own climate accounting for waste management in their region, based on site-specific conditions associated with types and amounts of waste, transport distances, type of treatment, exploitation and use of waste generated energy etc. The model can also be used as the basis for the preparation of useful documentation as the basis for information about waste systems utility in general, and as a basis for strategic reviews for Waste Norway and the waste sector in particular. Conclusions: The main conclusions from the project can be summarized as follows: 1. The results of the study clearly shows that to consider only one environmental indicator is too narrow approach to form the basis for decision making for selection of waste management solutions. 2. Net greenhouse gas emissions for waste management varies greatly, both between the different types of waste and treatment methods which are reviewed. The main results of the ranking of management methods in relation to the net greenhouse effect associated with the waste types and treatment methods are as follows: Recycling of materials

  2. Determining biodegradability of plastic materials under controlled and natural composting environments.

    Science.gov (United States)

    Mohee, R; Unmar, G

    2007-01-01

    With the advent of recently promulgated Government regulations on plastics in Mauritius, a study was initiated to examine the biodegradability of two different types of plastic, namely Willow Ridge Plastics - PDQ-H additive (Plastic A) and Ecosafe Plastic - TDPA additive (Plastic B) under controlled and natural composting environments. The results obtained from the controlled composting environment showed that the cumulative carbon dioxide evolution for Plastic A was much higher than that for Plastic B. Plastic A therefore showed a higher level of biodegradation in terms of CO2 evolution than Plastic B. However, from the regression analysis, it was found that the level of CO2 varying with time fitted the sigmoid type curves with very high correlation coefficients (R2 values: 0.9928, 0.9921 and 0.9816, for reference material, inoculum and Plastic A, respectively). The corresponding F-values obtained from the ANOVA analysis together with significance levels of pbiodegradability experiment were significant. The other experiment was undertaken to observe any physical change of Plastics A and B as compared to a reference plastic, namely, compostable plastic bag (Mater-Bi product-Plastic C), when exposed to a natural composting environment. Thermophilic temperatures were obtained for about 3-5 days of composting and the moisture content was in the range of 60-80% throughout the degradation process. It was observed that after 55 days of composting, Plastic C degraded completely while Plastic A and Plastic B did not undergo any significant degradation. It can be concluded that naturally based plastic made of starch would degrade completely in a time frame of 60 days, whereas plastics with biodegradable additive would require a longer time.

  3. Progress in the catalysts for cracking of waste plastics%废塑料裂解催化剂研究进展

    Institute of Scientific and Technical Information of China (English)

    伍艳辉; 吴高胜; 刘春燕; 朱志荣

    2014-01-01

    废塑料造成的环境污染日趋严重,处理回收废塑料已成为全球关注的问题。催化裂解作为一种新的塑料回收方法,具有高效、环保、无二次污染和产物油品质高等特点。综述了国内外废塑料裂解制油催化剂如分子筛、氧化物、黏土和过渡金属负载型双功能催化剂的研究进展。分子筛类、黏土类和无定形氧化铝-二氧化硅催化剂属酸性催化剂,其裂解废塑料机理为碳正离子机理;碱金属氧化物催化剂裂解废塑料机理为碳负离子机理;过渡金属负载型催化剂具有双功能,其中,金属活性位起加氢-脱氢作用,载体酸性位起异构化作用;而粉煤灰催化剂可同时实现废塑料与粉煤灰两种废弃物的综合回收利用。今后应注意在催化机理指导下,进一步提高催化剂性能,并研究对复杂废塑料混合物的催化裂解效果。%Because environmental pollution caused by waste plastics is getting worse,treatment and recov-ery of waste plastics has become a global concern. As a novel recovery method of plastics,catalytic crack-ing of waste plastics possessed the advantages of high efficiency,environment-friendliness and getting high quality fuel oil without secondary pollution. The progress in various catalysts for catalytic cracking of waste plastics such as molecular sieves,oxides,clay and transition metal supported bi-functional catalysts was reviewed in this paper. The catalytic degradation mechanisms of acidic catalysts such as molecular sieves, clay and amorphous Al2 O3-SiO2 followed carbocation mechanism,whereas alkali metal oxides catalysts for degrading waste plastic followed carbanion mechanism. Transition metal supported catalysts possessed the dual function,in which metal catalytic active sites played a role in hydrogenation-dehydrogenation,while acidic sites of the supports performed an isomerization function. Fly ash catalysts could recycle waste plas-tics and

  4. Effect of Die Head Temperature at Compounding Stage on the Degradation of Linear Low Density Polyethylene/Plastic Film Waste Blends after Accelerated Weathering

    Directory of Open Access Journals (Sweden)

    S. M. Al-Salem

    2016-01-01

    Full Text Available Accelerated weathering test was performed on blends of linear low density polyethylene (LLDPE and plastic film waste constituting the following percentages of polyolefin polymers (wt.%: LLDPE (46%, low density polyethylene (LDPE, 51%, high density polyethylene (HDPE, 1%, and polypropylene (PP, 2%. Compounded blends were evaluated for their mechanical and physical (optical properties. The impact of photodegradation on the formulated blends was studied, and loss of mechanical integrity was apparent with respect to both the exposure duration to weathering and waste content. The effect of processing conditions, namely, the die head temperature (DHT of the blown-film assembly used, was investigated in this work. It was witnessed that surpassing the melting point of the blends constituting polymers did not always result in a synergistic behaviour between polymers. This was suspected to be due to the loss of amorphous region that polyolefin polymers get subjected to with UV exposure under weathering conditions and the effect of the plastic waste constituents. The total change in colour (ΔE did not change with respect to DHT or waste content due to rapid change degradation on the material’s surface. Haze (% and light transmission (% decreased with the increase in waste content which was attributed to lack of miscibility between constituting polymers.

  5. Fuels by Waste Plastics Using Activated Carbon, MCM-41, HZSM-5 and Their Mixture

    Directory of Open Access Journals (Sweden)

    Miskolczi Norbert

    2016-01-01

    Full Text Available Waste material was pyrolyzed in a horizontal tubular reactor at 530-540°C using different catalysts, such as activated carbon, MCM-41, HZSM-5 and their mixtures. Products were investigated by gas-chromatography, EDXRFS and standardized methods. Catalysts significantly affected the yields of volatiles; e.g. HZSM-5 catalyst increased especially the yield of gaseous hydrocarbons, while MCM-41 catalyst was responsible for increasing the pyrolysis oil yield. Synergistic effects were found using mixtures of different catalysts. Furthermore the catalysts modified the main carbon frame of the products. Pyrolysis oil obtained over HZSM-5 catalyst contained large amounts of aromatics, while MCM-41 catalyst mainly isomerized the carbon frame. Regarding contaminants it was concluded, that the sulphur content could be significantly decreased by activated carbon, however it had only a slight effect to the other properties of the products.

  6. Using geographic information system (GIS) to determine waste ...

    African Journals Online (AJOL)

    lyndon

    Article Number: C32D5A757374 ... Full Length Research Paper ... Key words: Transfer, waste, landfill, station, geographical information system (GIS), geographical positioning ..... USEPA-United State Environmental Protection Agency (1995).

  7. determining the optimum proportion of shea waste in anaerobic co ...

    African Journals Online (AJOL)

    DEPT OF AGRICULTURAL ENGINEERING

    In search for an alternative source of energy, various feedstocks and wastes are being investi- gated to identify ... energy supply (Zauner and Kuntzel, 1986). Biogas comprises ... as it has been widely reported that high long-chain fatty acids.

  8. Some Exploitation Properties of Wood Plastic Hybrid Composites Based on Polypropylene and Plywood Production Waste

    Science.gov (United States)

    Kajaks, Janis; Kalnins, Karlis; Uzulis, Sandris; Matvejs, Juris

    2015-12-01

    During the last 20-30 years many researchers have paid attention to the studies of properties of thewood polymer composites (WPC). A lot of works are closely related to investigations of exploitation properties of wood fibres or wood flour containing polyolefine composites [1, 2]. The most useful from wide selection of polyolefines are polypropylenes, but timber industry waste materials comprising lignocellulose fibres are often used as reinforcement of WPC [3-12]. Plywood industry is not an exception - part of waste materials (by-products) are used for heat energy, i.e. burned. In this work we have approbated reinforcing of polypropylene (PP) with one of the plywood industry by-products, such as birch plywood sawdust (PSWD),which containswood fibre fractions with different length [13]. The main fraction (50%) includes fibres with length l = 0.5 - 1 mm. Our previous study [13] has confirmed that PSWD is a promising filler for PP reinforcing. Addition of PSWD up to 40-50 wt.% has increased WPC tensile and flexural modulus, but decreased deformation ability of PP matrix, impact strength, water resistance and fluidity of composite melts. It was shown [13] that modification of the composites with interfacial modifier - coupling agent maleated polypropylene (MAPP content up to 5-7 wt.%) considerably improved all the abovementioned properties. SEM investigations also confirmed positive action of coupling agent on strengthening of adhesion interaction between components wood and PP matrix. Another way how to make better properties of the WPC is to form hybridcomposites [1, 14-24]. Very popular WPC modifiers are nanoparticle additions like organonanoclays, which increase WPC physical-mechanical properties - microhardness, water resistance and diminish barrier properties and combustibility [1, 2, 14-17, 19, 20]. The goal of this study was to investigate organonanoclays influence on plywood production industry by-product birch plywood sawdust (PSWD) containing

  9. Learning strategy trumps motivational level in determining learning-induced auditory cortical plasticity.

    Science.gov (United States)

    Bieszczad, Kasia M; Weinberger, Norman M

    2010-02-01

    Associative memory for auditory-cued events involves specific plasticity in the primary auditory cortex (A1) that facilitates responses to tones which gain behavioral significance, by modifying representational parameters of sensory coding. Learning strategy, rather than the amount or content of learning, can determine this learning-induced cortical (high order) associative representational plasticity (HARP). Thus, tone-contingent learning with signaled errors can be accomplished either by (1) responding only during tone duration ("tone-duration" strategy, T-Dur), or (2) responding from tone onset until receiving an error signal for responses made immediately after tone offset ("tone-onset-to-error", TOTE). While rats using both strategies achieve the same high level of performance, only those using the TOTE strategy develop HARP, viz., frequency-specific decreased threshold (increased sensitivity) and decreased bandwidth (increased selectivity) (Berlau & Weinberger, 2008). The present study challenged the generality of learning strategy by determining if high motivation dominates in the formation of HARP. Two groups of adult male rats were trained to bar-press during a 5.0kHz (10s, 70dB) tone for a water reward under either high (HiMot) or moderate (ModMot) levels of motivation. The HiMot group achieved a higher level of correct performance. However, terminal mapping of A1 showed that only the ModMot group developed HARP, i.e., increased sensitivity and selectivity in the signal-frequency band. Behavioral analysis revealed that the ModMot group used the TOTE strategy while HiMot subjects used the T-Dur strategy. Thus, type of learning strategy, not level of learning or motivation, is dominant for the formation of cortical plasticity.

  10. 废塑料制品对土壤环境的影响及防治%On Soil Environment and Prevention of Waste Plastic Products

    Institute of Scientific and Technical Information of China (English)

    周辉

    2016-01-01

    With The Wide Application Of Plastic Products,Plastic Products Are Widely Used In All Walks Of Life,It Is Very Widespread Use In The Agricultural Industry,The Plastic Is Made Into A Plastic Film On The Growth Of Crops Have Been Very Positive,But From The Perspective Of Soil Management,Production And Use Of Plastic Products For The Local Soil Have Great Destructive Force,The Environmental Impact Is Great,This Paper Explores The Waste Plastic Products For Soil Environmental Impacts And Proposed Several Measures To Prevent The Point.%随着塑料制品的广泛应用,塑料制品在各行各业都有广泛的应用,在农业方面使用更是十分的广泛,塑料被制作成塑料薄膜对农作物的生长有非常积极的意义,但是从土壤管理的角度出发,塑料制品的制作以及使用对于当地的土壤有极大的破坏性,对于环境的影响也是极大,为此,本文探究了废塑料制品对土壤环境的影响并提出了防治的措施。

  11. Determination of Radioisotope Content by Measurement of Waste Package Dose Rates - 13394

    Energy Technology Data Exchange (ETDEWEB)

    Souza, Daiane Cristini B.; Gimenes Tessaro, Ana Paula; Vicente, Roberto [Nuclear and Energy Research Institute Brazil, Radioactive Waste Management Department IPEN/GRR, Sao Paulo. SP. (Brazil)

    2013-07-01

    The objective of this communication is to report the observed correlation between the calculated air kerma rates produced by radioactive waste drums containing untreated ion-exchange resin and activated charcoal slurries with the measured radiation field of each package. Air kerma rates at different distances from the drum surface were calculated with the activity concentrations previously determined by gamma spectrometry of waste samples and the estimated mass, volume and geometry of solid and liquid phases of each waste package. The water content of each waste drum varies widely between different packages. Results will allow determining the total activity of wastes and are intended to complete the previous steps taken to characterize the radioisotope content of wastes packages. (authors)

  12. 我国废塑料回收和进口现状浅析%Discussion on recycling and import of waste plastic in China

    Institute of Scientific and Technical Information of China (English)

    胡守仁

    2012-01-01

    Waste plastic is one of the main recyclable resources in China, with a large amount and variety from recycling and import. This paper demonstrated the kinds, quantity and location of waste plastics from recycling and import, as well as the recycling sources and methods.%废塑料是我国四大再生资源品种之一.废塑料国内回收和进口数量大、种类多。对我国废塑料国内产生和进口的种类、数量和地域,以及国内废塑料的回收渠道和方式进行了阐述。

  13. Determination of plastic additives in packaging by liquid chromatography coupled to high resolution mass spectrometry.

    Science.gov (United States)

    Moreta, Cristina; Tena, María-Teresa

    2015-10-02

    A simple and sensitive analytical method for the determination of several plastic additives in multilayer packaging based on solid-liquid extraction (SLE) and ultra-high performance liquid chromatography (UHPLC) coupled to variable wavelength (VWD) and time of flight mass spectrometry (TOF-MS) detectors is presented. The proposed method allows the simultaneous determination of fourteen additives belonging to different families such as antioxidants, slip agents and light stabilizers, as well as two oxidation products in only 9min. The developed method was validated in terms of linearity, matrix effect error, detection and quantification limits, repeatability and intermediate precision. The instrumental method showed satisfactory repeatability and intermediate precision at concentrations closed to LOQ with RSDs less than 7 and 20%, respectively, and LODs until 5000 times more sensitive than other GC-FID and HPLC-VWD methods previously reported. Also, focused ultrasound solid-liquid extraction (FUSLE) was optimized and evaluated to extract plastic additives from packaging. Extraction results obtained by FUSLE and SLE were compared to those obtained by pressurized liquid extraction (PLE). All extraction methods showed excellent extraction efficiency for slip agents, however quantitative recovery of all analytes was achieved only by SLE with just 5ml of hexane for 10h. Finally, the selected method was applied to the analysis of packaging samples where erucamide, Irgafos 168, oxidized Irgafos 168, Irganox 1076 and Irganox 1010 were detected and quantified. Copyright © 2015 Elsevier B.V. All rights reserved.

  14. Polybrominated diphenyl ethers in plastic products, indoor dust, sediment and fish from informal e-waste recycling sites in Vietnam: a comprehensive assessment of contamination, accumulation pattern, emissions, and human exposure.

    Science.gov (United States)

    Anh, Hoang Quoc; Nam, Vu Duc; Tri, Tran Manh; Ha, Nguyen Manh; Ngoc, Nguyen Thuy; Mai, Pham Thi Ngoc; Anh, Duong Hong; Minh, Nguyen Hung; Tuan, Nguyen Anh; Minh, Tu Binh

    2016-08-19

    Residue concentrations of polybrominated diphenyl ethers (PBDEs) in different kinds of samples including consumer products, indoor dust, sediment and fish collected from two e-waste recycling sites, and some industrial, urban and suburban areas in Vietnam were determined to provide a comprehensive assessment of the contamination levels, accumulation pattern, emission potential and human exposure through dust ingestion and fish consumption. There was a large variation of PBDE levels in plastic parts of obsolete electronic equipment (from 1730 to 97,300 ng/g), which is a common result observed in consumer plastic products reported elsewhere. PBDE levels in indoor dust samples collected from e-waste recycling sites ranged from 250 to 8740 ng/g, which were markedly higher than those in industrial areas and household offices. Emission rate of PBDEs from plastic parts of disposed electronic equipment to dust was estimated to be in a range from 3.4 × 10(-7) to 1.2 × 10(-5) (year(-1)) for total PBDEs and from 2.9 × 10(-7) to 7.2 × 10(-6) (year(-1)) for BDE-209. Some fish species collected from ponds in e-waste recycling villages contained elevated levels of PBDEs, especially BDE-209, which were markedly higher than those in fish previously reported. Overall, levels and patterns of PBDE accumulation in different kinds of samples suggest significant emission from e-waste sites and that these areas are potential sources of PBDE contamination. Intakes of PBDEs via fish consumption were generally higher than those estimated through dust ingestion. Intake of BDE-99 and BDE-209 through dust ingestion contributes a large proportion due to higher concentrations in dust and fish. Body weight normalized daily intake through dust ingestion estimated for the e-waste recycling sites (0.10-3.46 ng/day/kg body wt.) were in a high range as compared to those reported in other countries. Our results highlight the potential releases of PBDEs from informal recycling activities

  15. Recovery of carbon fibres and production of high quality fuel gas from the chemical recycling of carbon fibre reinforced plastic wastes

    OpenAIRE

    Yildirir, E; Onwudili, JA; Williams, PT

    2014-01-01

    A solvolysis process to depolymerize the resin fraction of carbon fibre reinforced plastic waste to recover carbon fibre, followed by hydrothermal gasification of the liquid residual product to produce fuel gas was investigated using batch reactors. The depolymerisation reactions were carried out in ethylene glycol and ethylene glycol/water mixtures at near-critical conditions of the two solvents. With ethylene glycol alone the highest resin removal of 92.1% was achieved at 400 °C. The additi...

  16. The Synergy between Scuba Diving and Household Behaviour: Testing Plastic and Food Waste "The use of natural habitats for tourism education"

    OpenAIRE

    Soares Mota, Luís Cândido

    2014-01-01

    The activity of scuba diving is used for studying behaviours of U.S. visitors to a popular tourist destination in Mexico. The impact created by human activity can produce marine debris and therefore affect the marine environment. The subpopulation of 181 divers was tested for their current household practices regarding discarding plastic and food waste, providing quantitative statistics for divers’ referential behaviour. Prior to partaking in scuba diving, certified, trainee, and “one-day-exp...

  17. Pollution characteristics and health risk assessment of volatile organic compounds emitted from different plastic solid waste recycling workshops.

    Science.gov (United States)

    He, Zhigui; Li, Guiying; Chen, Jiangyao; Huang, Yong; An, Taicheng; Zhang, Chaosheng

    2015-04-01

    The pollution profiles of volatile organic compounds (VOCs) emitted from different recycling workshops processing different types of plastic solid waste (PSW) and their health risks were investigated. A total of 64 VOCs including alkanes, alkenes, monoaromatics, oxygenated VOCs (OVOCs), chlorinated VOCs (ClVOCs) and acrylonitrile during the melting extrusion procedure were identified and quantified. The highest concentration of total VOCs (TVOC) occurred in the poly(acrylonitrile-butadiene styrene) (ABS) recycling workshop, followed by the polystyrene (PS), polypropylene (PP), polyamide (PA), polyvinyl chloride (PVC), polyethylene (PE) and polycarbonate (PC) workshops. Monoaromatics were found as the major component emitted from the ABS and PS recycling workshops, while alkanes were mainly emitted from the PE and PP recycling processes, and OVOCs from the PVC and PA recycling workshops. According to the occupational exposure limits' (OEL) assessment, the workers suffered acute and chronic health risks in the ABS and PS recycling workshops. Meanwhile, it was found that most VOCs in the indoor microenvironments were originated from the melting extrusion process, while the highest TVOC concentration was observed in the PS rather than in the ABS recycling workshop. Non-cancer hazard indices (HIs) of all individual VOCs were <1.0, whereas the total HI in the PS recycling workshop was 1.9, posing an adverse chronic health threat. Lifetime cancer risk assessment suggested that the residents also suffered from definite cancer risk in the PS, PA, ABS and PVC recycling workshops.

  18. A survey of Trace Metals Determination in Hospital Waste Incinerator in Lucknow City, India

    Directory of Open Access Journals (Sweden)

    Ranjan Kumar

    2004-08-01

    Full Text Available Information on the elemental content of incinerator burning of human organ, animal and medical waste is scanty in India Nineteen trace elements were analyzed in the incinerator ash from four major hospitals, one municipal waste incinerator and two R & D laboratories engaged in animal experiment in Lucknow city. Concentrations of Zinc and Lead were found to be very high in comparison to other metals due to burning of plastic products. The source of Ca, P and K are mainly bone, teeth and other animal organs. A wide variation in trace concentration of several toxic elements have been seen due to variation in initial waste composition, design of the incinerator and operating conditions.

  19. Investigating the determinants of contractor's construction and demolition waste management behavior in Mainland China.

    Science.gov (United States)

    Wu, Zezhou; Yu, Ann T W; Shen, Liyin

    2016-09-06

    The abundant generation of construction and demolition (C&D) waste presents a significant challenge to the sustainable development of the construction industry in Mainland China. As the implementer of construction activities, the contractor's C&D waste management performance plays an important role in C&D waste minimization. This paper aims to investigate the determinants of the contractor's C&D waste management behavior in Mainland China. The Theory of Planned Behavior (TPB) was selected as the basis of the theoretical model. In addition, three contextual constructs (i.e., economic viability, governmental supervision, and project constraints) were introduced, formulating the initial model. Based on the initial model, eight constructs were identified and seven hypotheses were proposed. A questionnaire survey was conducted to collect data and a Structural Equation Modeling (SEM) analysis was employed to test the proposed hypotheses. Results showed that the C&D waste management intention is not a significant determinant of contractor's C&D waste management behavior. The most important determinant is economic viability, followed by governmental supervision as the second most important determinant. Nevertheless, the construct of project constraints is an insignificant determinant for contractor's adoption of C&D waste management behavior. The research findings imply that, in Mainland China, the government, at this stage, plays an important role in guiding and promoting the contractor to exhibit better C&D waste management behavior.

  20. Using nudges to reduce waste? The case of Toronto's plastic bag levy.

    Science.gov (United States)

    Rivers, Nicholas; Shenstone-Harris, Sarah; Young, Nathan

    2017-03-01

    The overuse of disposable plastic bags is a major environmental problem across the globe. In recent years, numerous jurisdictions have sought to curb disposable bag use by implementing a levy or fee at the point of purchase. These levies are typically small and symbolic (around $0.05 per bag), but serve as a highly-visible and continuous reminder to consumers. As such, they are consistent with nudging policies that seek to encourage broad changes in behaviour through small, non-coercive measures that influence people's thinking about an issue. While existing empirical evidence suggests that nudges are highly effective in reducing disposable bag use, we argue that many of these studies are flawed because they lack adequate temporal and geographic controls. We use longitudinal data from four waves of a major Canadian survey to analyze the effect of a disposable bag levy in the City of Toronto. Controlling for demographics and changes in social norms over time, we find that the levy increased the use of reusable shopping bags by 3.4 percentage points. Moreover, we find that the impact of the policy was highly variable across behavioural and demographic groups. The levy was highly effective in encouraging people who already used reusable bags to use them more frequently, while having no effect on infrequent users. We also find that the effects are limited to households with high socio-economic status (as measured by income, educational attainment, and housing situation). This suggests important limitations for nudging policy more generally, as people with lower socio-economic status appear to have been unaffected by this behavioural prompt.

  1. Investigation on an innovative technology for wet separation of plastic wastes.

    Science.gov (United States)

    Lupo, Emanuela; Moroni, Monica; La Marca, Floriana; Fulco, Simone; Pinzi, Valentina

    2016-05-01

    This paper presents an original device for the separation of plastic polymers from mixtures. Due to the combination of a characteristic flow pattern developing within the apparatus and density, shape and size differences among two or more polymers, this device allows their separation into two products, one collected within the instrument and the other one expelled through its outlet ducts. Experimental tests have been conducted to investigate the effectiveness of the apparatus, using two geometric arrangements, nine hydraulic configurations and three selections of polymers at three stages of a material life cycle. Tests with samples composed of a single typology of polymer have been used to understand the interaction between the particles and the carrying fluid within the apparatus in different hydraulic configurations and geometric arrangements. Multi-material tests are essential to simulate the real conditions in an industrial recycling plant. The separation results have been evaluated in terms of grade and recovery of a useful material. Under the proper hydraulic configurations, the experimentation showed that it is possible to produce an almost pure concentrate of Polyethylene Terephthalate (PET) from a mixture of 85% PET and 15% Polycarbonate (PC) (concentrate grade and recovery equal to 99.5% and 95.1%) and a mixture of 85% PET and 15% Polyvinyl Chloride (PVC) (concentrate grade and recovery equal to 97.9% and 100.0%). It is further demonstrated that almost pure concentrates of PVC and PC can be produced from a mixture of 85% PVC and 15% PC (PVC grade and recovery equal to 99.9% and 99.7%) and a mixture of 85% PC and 15% PVC (PC grade and recovery equal to 99.0% and 99.5%). Copyright © 2016 Elsevier Ltd. All rights reserved.

  2. Measuring the Biodegradability of Plastic Polymers in Olive-Mill Waste Compost with an Experimental Apparatus

    Directory of Open Access Journals (Sweden)

    Francesco Castellani

    2016-01-01

    Full Text Available The use of biodegradable polymers is spreading in agriculture to replace those materials derived from petroleum, thus reducing the environmental concerns. However, to issue a significant assessment, biodegradation rate must be measured in case-specific standardized conditions. In accordance with ISO 14855-1, we designed and used an experimental apparatus to evaluate the biodegradation rate of three biopolymers based on renewable resources, two poly(ε-caprolactone (PCL composites, and a compatibilized polylactic acid and polybutyrate (PLA/PBAT blend. Biodegradation tests were carried out under composting condition using mature olive-mill waste (OMW compost as inoculum. Carbon dioxide emissions were automatically recorded by infrared gas detectors and also trapped in saturated Ba(OH2 solution and evaluated via a standard titration method to check the results. Some of the samples reached more than 80% biodegradation in less than 20 days. Both the experimental apparatus and the OMW compost showed to be suitable for the cases studied.

  3. Report: recycling of flame-retarded plastics from waste electric and electronic equipment (WEEE).

    Science.gov (United States)

    Schlummer, Martin; Mäurer, Andreas; Leitner, Thomas; Spruzina, Walter

    2006-12-01

    Shredder residues produced in plants processing waste electric and electronic equipment are excluded from material recycling due to a variety of polymeric materials and the presence of brominated flame retardants (BFR), which might contain banned polybrominated diphenyl ethers or toxic polybrominated dioxins and furans (PBDD/F). Herein we present a technological approach to transfer a significant portion of the shredder residue into recycled polymers. The technological approach consists of a density-based enrichment of styrenics, which are subjected to a solvolysis process (CreaSolv process) in a second stage. This stage allows the elimination of non-target polymers and extraction of BFR and PBDD/F. Pilot processing of 11.5 and 50 kg shredder residues indicated a material yield of about 50% in the density stage and 70-80% in the CreaSolv process, and an effective removal of BFR additives. The recycled products were proved to comply with threshold values defined by the European directive on the restriction of hazardous substances (RoHS) and the German Chemikalienverbotsverordnung. Mechanical material properties exhibited high tensile and flexural modules as well as slight impact strength, which qualify the products for applications in new electronic equipment.

  4. 废旧聚苯乙烯塑料再生再利用技术现状%Research on Techniques of Waste Polystyrene Plastics Recycling and Reusing

    Institute of Scientific and Technical Information of China (English)

    邓亮; 徐海萍; 谢华清; 李志杰

    2014-01-01

    主要介绍了废旧聚苯乙烯塑料的回收再生、再利用技术现状,涵盖了在涂料、胶黏剂、化工产品、建筑材料等领域的再生应用,重点讨论了熔融法再生和用于生产仿木建材的关键技术。通过分析和比较不同的再生再利用工艺技术,期望对未来废旧聚苯乙烯塑料资源化的发展方向有一定的指导意义。%The recycling and reusing techniques of waste polystyrene plastic, including the polystyrene foamed plastics, were intro-duced in this paper. It included the current situation of making coating, adhesive, chemistry products, building materials and pyrolytic technique, and mainly discussed the key techniques of melt extrusion and making wood-like plastics. Especially, the performance of different techniques of recycling and reusing process were also analyzed and compared. And the future development direction of waste polystyrene plastics recycling had been looked to.

  5. Groundwater Quality Assessment for Waste Management Area U: First Determination

    Energy Technology Data Exchange (ETDEWEB)

    Hodges, Floyd N.; Chou, Charissa J.

    2000-08-04

    As a result of the most recent recalculation one of the indicator parameters, specific conductance, exceeded its background value in downgradient well 299-W19-41, triggering a change from detection monitoring to groundwater quality assessment program. The major contributors to the higher specific conductance are nonhazardous constituents (i.e., sodium, calcium, magnesium, chloride, sulfate, and bicarbonate). Nitrate, chromium, and technetium-99 are present and are increasing; however, they are significantly below their drinking waster standards. Interpretation of groundwater monitoring data indicates that both the nonhazardous constituents causing elevated specific conductance in groundwater and the tank waste constituents present in groundwater at the waste management area are a result of surface water infiltration in the southern portion of the facility. There is evidence for both upgradient and waste management area sources for observed nitrate concentrations. There is no indication of an upgradient source for the observed chromium and technetium-99.

  6. Determination of performance criteria for high-level solidified nuclear waste

    Energy Technology Data Exchange (ETDEWEB)

    Heckman, R.A.; Holdsworth, T.

    1979-05-07

    To minimize radiological risk from the operation of a waste management system, performance limits on volatilization, particulate dispersion, and dissolution characteristics of solidified high level waste must be specified. The results show clearly that the pre-emplacement environs are more limiting in establishing the waste form performance criteria than the post-emplacement environs. Absolute values of expected risk are very sensitive to modeling assumptions. The transportation and interim storage operations appear to be most limiting in determining the performance characteristics required. The expected values of risk do not rely upon the repositories remaining intact over the potentially hazardous lifetime of the waste.

  7. 40 CFR 260.34 - Standards and criteria for non-waste determinations.

    Science.gov (United States)

    2010-07-01

    ... WASTES (CONTINUED) HAZARDOUS WASTE MANAGEMENT SYSTEM: GENERAL Rulemaking Petitions § 260.34 Standards and... determination for hazardous secondary material which is reclaimed in a continuous industrial process if the... recycled as specified in § 260.43 and on the following criteria: (1) The extent that the management of...

  8. 40 CFR 761.358 - Determining the PCB concentration of samples of waste.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Determining the PCB concentration of samples of waste. 761.358 Section 761.358 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... concentration of samples of waste. Use either Method 3500B/3540C or Method 3500B/3550B from EPA's SW-846, Test...

  9. Determinants of households' willingness-to-pay for private solid waste management services in Ibadan, Nigeria.

    Science.gov (United States)

    Rahji, M A Y; Oloruntoba, Elizabeth O

    2009-12-01

    The study examined the determinants of willingness-to-pay for private solid waste disposal systems by urban households in Ibadan, Nigeria. A multistage random sampling technique was used to select 552 households for the study. Data obtained from survey were analysed using a logit model-based contingent valuation. Evidence from the logit model indicated that seven variables had significant influence on the households' willingness-to-pay. Of these, income and asset owned were positive and significant at P willingness-to-pay and firm services were negative and significant at P willingness-to-pay for solid waste disposal. The study recommends government intervention in a variety of forms such as encouraging public-private participation in solid waste disposal, an aggressive environmental clean-up campaign, decentralization of Waste Management Boards and privatization of some aspects of waste management to ameliorate solid waste problems and improve health.

  10. Effects of Temperature Rise Rate on Pyrolysis of Plastic Wastes%升温速率对废塑料热解过程的影响

    Institute of Scientific and Technical Information of China (English)

    石耀华; 马晓波; 陈德珍; 周恭明

    2011-01-01

    In this paper, pyrolysis experiments of plastic wastes, i.e. polyethylene ( PE), polypropylene (PP), polyvinylchloride(PVC) and their mixtures, were made at temperature rise rates of lO℃/min,20℃/min and 30℃/min in nitrogen atmosphere in which the temperature was from 20℃ to 700℃.Effects of pyrolysis process of waste plastics at different temperature rise rate were analyzed, and kinetics investigations were carried out by Coast - Redfern integration method. Pyrolysis characteristics and kinetic parameters of these three kinds of plastic wastes and their mixtures were obtained. The results show that temperature rise rate has an influence on pyrolysis rate, pyrolysis temperature range, activation energy and pre -exponential factor. The greater temperature rise rate, the faster pyrolysis reacts, the greater activation energy required, the more energy consumption on pyrolysis process. Therefore, in the pyrolysis process of waste plastics, temperature rise rate, pyrolysis materials, pyrolysis temperature and other conditions should be considered integrally. This research can provide theoretical and experimental data for the design of pyrolysis technology of plastic wastes.%选取废旧塑料聚乙烯(polyethylene,PE)、聚丙烯(polypropylene,PP)、聚氯乙烯(polyvi-nyl chloride,PVC)及其混合物,在氮气气氛下进行热解实验,实验温度从室温到700℃,升温速率分别为10℃/min、20℃/min和30℃/min.讨论了不同升温速率对废塑料热解过程的影响,并采用Coast-Redfem法进行了热解动力学分析,得到了三种废塑料及其混合物的热解特性及反应动力学、参数.研究结果表明,升温速率对热解速率,热解温度段,活化能,频率因子都有影响.升温速率越快,热解反应越快,所需的活化能也越大,热解过程对能量的消耗越多.因此,在废塑料热解过程中,要综合考虑升温速率,热解原料,热解温度等条件.本文可为废塑料热解工艺的研究提供理论依据和参考数据.

  11. The Determination of Anionic Surfactants in Natural and Waste Waters.

    Science.gov (United States)

    Crisp, P. T.; And Others

    1983-01-01

    Background information, procedures, and results of an experiment suitable for measuring subpart per million concentrations of anionic surfactants in natural waters and waste effluents are provided. The experiment required only a spectrophotometer or filter photometer and has been successfully performed by students in an undergraduate environmental…

  12. The Determination of Anionic Surfactants in Natural and Waste Waters.

    Science.gov (United States)

    Crisp, P. T.; And Others

    1983-01-01

    Background information, procedures, and results of an experiment suitable for measuring subpart per million concentrations of anionic surfactants in natural waters and waste effluents are provided. The experiment required only a spectrophotometer or filter photometer and has been successfully performed by students in an undergraduate environmental…

  13. An Assessment of the Compressive Strength of Glass Reinforced Plastic Waste Filled Concrete for Potential Applications in Construction

    Directory of Open Access Journals (Sweden)

    Asokan Pappu

    2010-03-01

    Full Text Available

    Efforts were made to recycle Glass reinforced plastic (GRP waste powder in concrete products and assess its compressive strength to comply with British Standards for use in construction applications. More than 90 GRP waste-filled concrete specimens were

  14. Determination of Polymer Additives-Antioxidants, Ultraviolet Stabilizers, Plasticizers and Photoinitiators in Plastic Food Package by Accelerated Solvent Extraction Coupled with High-Performance Liquid Chromatography.

    Science.gov (United States)

    Li, Bo; Wang, Zhi-Wei; Lin, Qin-Bao; Hu, Chang-Ying; Su, Qi-Zhi; Wu, Yu-Mei

    2015-07-01

    An analytical method for the quantitative determination of 4 antioxidants, 9 ultraviolet (UV) stabilizers, 12 phthalate plasticizers and 2 photoinitiators in plastic food package using accelerated solvent extraction (ASE) coupled with high-performance liquid chromatography-photodiode array detector (HPLC-PDA) has been developed. Parameters affecting the efficiency in the process such as extraction and chromatographic conditions were studied in order to determine operating conditions. The analytical method of ASE-HPLC showed good linearity with good correlation coefficients (R ≥ 0.9833). The limits of detection and quantification were between 0.03 and 0.30 µg mL(-1) and between 0.10 and 1.00 µg mL(-1) for 27 analytes. Average spiked recoveries for most analytes in samples were >70.4% at 10, 20 and 40 µg g(-1) spiked levels, except UV-9 and Irganox 1010 (58.6 and 64.0% spiked at 10 µg g(-1), respectively), the relative standard deviations were in the range from 0.4 to 15.4%. The methodology has been proposed for the analysis of 27 polymer additives in plastic food package. © The Author 2014. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  15. Plastic value chains

    DEFF Research Database (Denmark)

    Baxter, John; Wahlstrom, Margareta; Zu Castell-Rüdenhausen, Malin

    2014-01-01

    Optimizing plastic value chains is regarded as an important measure in order to increase recycling of plastics in an efficient way. This can also lead to improved awareness of the hazardous substances contained in plastic waste, and how to avoid that these substances are recycled. As an example...

  16. Challenges in plastics recycling

    DEFF Research Database (Denmark)

    Pivnenko, Kostyantyn; Jakobsen, L. G.; Eriksen, Marie Kampmann

    2015-01-01

    Recycling of waste plastics still remains a challenging area in the waste management sector. The current and potential goals proposed on EU or regional levels are difficult to achieve, and even to partially fullfil them the improvements in collection and sorting should be considerable. A study...... was undertaken to investigate the factors affecting quality in plastics recycling. The preliminary results showed factors primarily influencing quality of plastics recycling to be polymer cross contamination, presence of additives, non-polymer impurities, and polymer degradation. Deprivation of plastics quality......, with respect to recycling, has been shown to happen throughout the plastics value chain, but steps where improvements may happen have been preliminary identified. Example of Cr in plastic samples analysed showed potential spreading and accumulation of chemicals ending up in the waste plastics. In order...

  17. Spectroscopic method for the determination of the ionic site concentration in solvent polymeric membranes and membrane plasticizers.

    Science.gov (United States)

    Gyurcsányi, Robert E; Lindner, Erno

    2002-08-15

    The built-in site density of either fixed sites or mobile hydrophobic ion sites determines whether a membrane is permselective for cations or anions of the sample. The molar ratio of the ionophore to the intrinsic or added ionic sites in an ion-selective membrane significantly influences the potentiometric response of ionophore-based electrodes. Consequently, full knowledge of the "site inventory" in an ion-selective membrane maybe essential when new, uncharacterized polymers or plasticizers are implemented for ion-selective electrode fabrication. A simple spectroscopic method was developed for the fast and accurate determination of the ionic site concentration (covalently attached functionalized groups or impurities) in plasticized polymeric membranes and membrane plasticizers. The method is based on the determination of the degree of protonation of hydrogen ion-selective chromoionophores incorporated into these membranes or dissolved in the membrane plasticizers. In electroneutral membranes, the concentration of the positively charged, protonated ionophore and the total concentration of negative sites are equal. The method was applied for the determination of ionic sites (both positively and negatively charged) in PVC materials (different purity grade, and bearing various functional groups), polyurethanes (aliphatic, aromatic, and polycarbonate-based), and selected Fluka plasticizers (2-nitrophenyl octyl ether and 2-ethylhexyl sebacate). The technique proved to be appropriate for fast quantification of ionic impurities in hydrophobic, optically transparent materials.

  18. Detailed compositional characterization of plastic waste pyrolysis oil by comprehensive two-dimensional gas-chromatography coupled to multiple detectors.

    Science.gov (United States)

    Toraman, Hilal E; Dijkmans, Thomas; Djokic, Marko R; Van Geem, Kevin M; Marin, Guy B

    2014-09-12

    The detailed compositional characterization of plastic waste pyrolysis oil was performed with comprehensive two-dimensional GC (GC×GC) coupled to four different detectors: a flame ionization detector (FID), a sulfur chemiluminescence detector (SCD), a nitrogen chemiluminescence detector (NCD) and a time of flight mass spectrometer (TOF-MS). The performances of different column combinations were assessed in normal i.e. apolar/mid-polar and reversed configurations for the GC×GC-NCD and GC×GC-SCD analyses. The information obtained from the four detectors and the use of internal standards, i.e. 3-chlorothiophene for the FID and the SCD and 2-chloropyridine for the NCD analysis, enabled the identification and quantification of the pyrolysis oil in terms of both group type and carbon number: hydrocarbon groups (n-paraffins, iso-paraffins, olefins and naphthenes, monoaromatics, naphthenoaromatics, diaromatics, naphthenodiaromatics, triaromatics, naphthenotriaromatics and tetra-aromatics), nitrogen (nitriles, pyridines, quinolines, indole, caprolactam, etc.), sulfur (thiols/sulfides, thiophenes/disulfides, benzothiophenes, dibenzothiophenes, etc.) and oxygen containing compounds (ketones, phenols, aldehydes, ethers, etc.). Quantification of trace impurities is illustrated for indole and caprolactam. The analyzed pyrolysis oil included a significant amount of nitrogen containing compounds (6.4wt%) and to a lesser extent sulfur containing compounds (0.6wt%). These nitrogen and sulfur containing compounds described approximately 80% of the total peak volume for respectively the NCD and SCD analysis. TOF-MS indicated the presence of the oxygen containing compounds. However only a part of the oxygen containing compounds (2.5wt%) was identified because of their low concentrations and possible overlap with the complex hydrocarbon matrix as no selective detector or preparative separation for oxygen compounds was used.

  19. Catalytic multi-stage liquefaction of coal at HTI: Bench-scale studies in coal/waste plastics coprocessing

    Energy Technology Data Exchange (ETDEWEB)

    Pradhan, V.R.; Lee, L.K.; Stalzer, R.H. [Hydrocarbon Technologies, Inc., Lawrenceville, NJ (United States)] [and others

    1995-12-31

    The development of Catalytic Multi-Stage Liquefaction (CMSL) at HTI has focused on both bituminous and sub-bituminous coals using laboratory, bench and PDU scale operations. The crude oil equivalent cost of liquid fuels from coal has been curtailed to about $30 per barrel, thus achieving over 30% reduction in the price that was evaluated for the liquefaction technologies demonstrated in the late seventies and early eighties. Contrary to the common belief, the new generation of catalytic multistage coal liquefaction process is environmentally very benign and can produce clean, premium distillates with a very low (<10ppm) heteroatoms content. The HTI Staff has been involved over the years in process development and has made significant improvements in the CMSL processing of coals. A 24 month program (extended to September 30, 1995) to study novel concepts, using a continuous bench scale Catalytic Multi-Stage unit (30kg coal/day), has been initiated since December, 1992. This program consists of ten bench-scale operations supported by Laboratory Studies, Modelling, Process Simulation and Economic Assessments. The Catalytic Multi-Stage Liquefaction is a continuation of the second generation yields using a low/high temperature approach. This paper covers work performed between October 1994- August 1995, especially results obtained from the microautoclave support activities and the bench-scale operations for runs CMSL-08 and CMSL-09, during which, coal and the plastic components for municipal solid wastes (MSW) such as high density polyethylene (HDPE)m, polypropylene (PP), polystyrene (PS), and polythylene terphthlate (PET) were coprocessed.

  20. Analysis of the treatment of plastic from electrical and electronic waste in the Republic of Serbia and the testing of the recycling potential of non-metallic fractions of printed circuit boards

    Directory of Open Access Journals (Sweden)

    Vučinić Aleksandra S.

    2017-01-01

    Full Text Available This paper presents the analysis of the quantity of plastic and waste printed circuit boards obtained after the mechanical treatment of electrical and electronic waste (E-waste in the Republic of Serbia, as well as the recycling of non-metallic fractions of waste printed circuit boards. The aim is to analyze the obtained recycled material and recommendation for possible application of recyclables. The data on the quantities and treatment of plastics and printed circuit boards obtained after the mechanical treatment of WEEE, were gained through questionnaires sent to the operators who treat this type of waste. The results of the questionnaire analysis showed that in 2014 the dismantling of E-waste isolated 1,870.95 t of plastic and 499.85 t of printed circuit boards. In the Republic of Serbia, E-waste recycling is performed exclusively by using mechanical methods. Mechanical methods consist of primary crushing and separation of the materials which have a utility value as secondary raw materials, from the components and materials that have hazardous properties. Respect to that, the recycling of printed circuit boards using some of the metallurgical processes with the aim of extracting copper, precious metals and non-metallic fraction is completely absent, and the circuit boards are exported as a whole. Given the number of printed circuit boards obtained by E-waste dismantling, and the fact that from an economic point of view, hydrometallurgical methods are very suitable technological solutions in the case of a smaller capacity, there is a possibility for establishing the facilities in the Republic of Serbia for the hydrometallurgical treatment that could be used for metals extraction, and non-metallic fractions, which also have their own value. Printed circuit boards granulate obtained after the mechanical pretreatment and the selective removal of metals by hydrometallurgical processes was used for the testing of the recycling potential

  1. Determination of the optimal area of waste incineration in a rotary kiln using a simulation model.

    Science.gov (United States)

    Bujak, J

    2015-08-01

    The article presents a mathematical model to determine the flux of incinerated waste in terms of its calorific values. The model is applicable in waste incineration systems equipped with rotary kilns. It is based on the known and proven energy flux balances and equations that describe the specific losses of energy flux while considering the specificity of waste incineration systems. The model is universal as it can be used both for the analysis and testing of systems burning different types of waste (municipal, medical, animal, etc.) and for allowing the use of any kind of additional fuel. Types of waste incinerated and additional fuel are identified by a determination of their elemental composition. The computational model has been verified in three existing industrial-scale plants. Each system incinerated a different type of waste. Each waste type was selected in terms of a different calorific value. This allowed the full verification of the model. Therefore the model can be used to optimize the operation of waste incineration system both at the design stage and during its lifetime. Copyright © 2015 Elsevier Ltd. All rights reserved.

  2. 废旧塑料改性沥青混合料动态模量研究%Research on dynamic modulus of waste plastic modified asphalt mixture

    Institute of Scientific and Technical Information of China (English)

    张倩; 谢来斌; 李彦伟; 何勇海; 刘建

    2011-01-01

    Waste plastic is reused in pavement engineering in this research. The purpose of the study is to probe the possibility of using waste plastic in asphalt mixture as a kind of modifier so as to find a way to solve the problem of the waste plastic disposal. High Density Polyethylene plastic bags obtained from supermarket were shredded into pieces and were added into asphalt mixture at three percentages of 2%, 5% and 8%. The corresponding control samples were also made and tested. Three different temperatures were used (4°C, 21. 3°C and 39. 2°C) and the frequencies ranged from 0. 1 Hz to 25 Hz in this dynamic modulus test. When compared with the test results of the control samples, almost all the dynamic modulus of the plastic modified samples( except 4 results) are greater than those of the control samples. No regular pattern is shown in the test results of the phase angle. Modified asphalt mixture with 2% plastic is of the greatest dynamic modulus and phase angle.%针对目前大量废旧塑料处置问题,尝试将其用于改性沥青混合料,以探索其在道路工程中使用的可能性.采用超市废旧高密度聚乙烯购物塑料袋,将其切碎后按照2%.5%和8%的掺量制作沥青混合料试件,采用三种试验温度在六种加载频率下进行动态模量试验,与未掺加塑料混合料的相应指标进行对比.试验结果显示在各个试验温度和加载频率下,掺加塑料屑的混合料动态模量普遍提高.掺加塑料与否对相位角指标的影响未呈现一定规律.在各个试验温度和加载频率下,2%塑料掺量混合料均具有较高的动态模量和相位角.

  3. Pollution characteristics of volatile organic compounds, polycyclic aromatic hydrocarbons and phthalate esters emitted from plastic wastes recycling granulation plants in Xingtan Town, South China

    Science.gov (United States)

    Huang, De-Yin; Zhou, Shun-Gui; Hong, Wei; Feng, Wei-Feng; Tao, Liang

    2013-06-01

    With the aim to investigate the main pollution characteristics of exhaust gases emitted from plastic waste recycling granulation plants, mainly volatile organic compounds (VOCs), polycyclic aromatic hydrocarbons (PAHs) and phthalate esters (PAEs) were analyzed in Xingtan Town, the largest distribution center of plastic waste recycling in China. Both inside and outside the plants, the total concentrations of volatile monocyclic aromatic hydrocarbons (MAHs), PAHs and PAEs ranged from 2000 to 3000 μg m-3, 450 to 1200 ng m-3, and 200 to 1200 ng m-3, respectively. Their concentration levels inside the plants were higher than those outside the plants, and PAHs and PAEs were mainly distributed in the gas-phase. Notably, highly toxic benzo[a]pyrene (BaP) could be detected inside the plants, and harmful PAEs could be detected not only inside but also outside the plants, although PAEs are non-volatile. The exhaust gas composition and concentration were related to the plastic feedstock and granulation temperature.

  4. 废塑料在炼焦配煤中的应用研究%Study on application of waste plastics in coking coal blending

    Institute of Scientific and Technical Information of China (English)

    李海桥; 崔洁; 阎定兵; 陈战州

    2015-01-01

    介绍了宁钢应用塑料型煤技术,在满足焦炭质量要求的前提下,扩大了炼焦煤中添加废塑料的比例,而且在限定废塑料添加比例的条件下稳定了焦炭质量,为科学、合理、经济地治理"白色污染"提供了理论依据和工业经验.%This paper introduces the practice of Ningbo Steel in applying plastic coal briquette tech-nology. On condition of matching the coke quality requirement,the ratio of blended waste plastic in coking coal is increased,and the coke quality is stabilized on condition of limiting the blending ratio of waste plastic. The study provides theoretical basis and industrial reference in scientific,reasonable and economical control of "white pollution".

  5. Independent genetic control of maize (Zea mays L.) kernel weight determination and its phenotypic plasticity.

    Science.gov (United States)

    Alvarez Prado, Santiago; Sadras, Víctor O; Borrás, Lucas

    2014-08-01

    Maize kernel weight (KW) is associated with the duration of the grain-filling period (GFD) and the rate of kernel biomass accumulation (KGR). It is also related to the dynamics of water and hence is physiologically linked to the maximum kernel water content (MWC), kernel desiccation rate (KDR), and moisture concentration at physiological maturity (MCPM). This work proposed that principles of phenotypic plasticity can help to consolidated the understanding of the environmental modulation and genetic control of these traits. For that purpose, a maize population of 245 recombinant inbred lines (RILs) was grown under different environmental conditions. Trait plasticity was calculated as the ratio of the variance of each RIL to the overall phenotypic variance of the population of RILs. This work found a hierarchy of plasticities: KDR ≈ GFD > MCPM > KGR > KW > MWC. There was no phenotypic and genetic correlation between traits per se and trait plasticities. MWC, the trait with the lowest plasticity, was the exception because common quantitative trait loci were found for the trait and its plasticity. Independent genetic control of a trait per se and genetic control of its plasticity is a condition for the independent evolution of traits and their plasticities. This allows breeders potentially to select for high or low plasticity in combination with high or low values of economically relevant traits.

  6. Determination of fossil carbon content in Swedish waste fuel by four different methods.

    Science.gov (United States)

    Jones, Frida C; Blomqvist, Evalena W; Bisaillon, Mattias; Lindberg, Daniel K; Hupa, Mikko

    2013-10-01

    This study aimed to determine the content of fossil carbon in waste combusted in Sweden by using four different methods at seven geographically spread combustion plants. In total, the measurement campaign included 42 solid samples, 21 flue gas samples, 3 sorting analyses and 2 investigations using the balance method. The fossil carbon content in the solid samples and in the flue gas samples was determined using (14)C-analysis. From the analyses it was concluded that about a third of the carbon in mixed Swedish waste (municipal solid waste and industrial waste collected at Swedish industry sites) is fossil. The two other methods (the balance method and calculations from sorting analyses), based on assumptions and calculations, gave similar results in the plants in which they were used. Furthermore, the results indicate that the difference between samples containing as much as 80% industrial waste and samples consisting of solely municipal solid waste was not as large as expected. Besides investigating the fossil content of the waste, the project was also established to investigate the usability of various methods. However, it is difficult to directly compare the different methods used in this project because besides the estimation of emitted fossil carbon the methods provide other information, which is valuable to the plant owner. Therefore, the choice of method can also be controlled by factors other than direct determination of the fossil fuel emissions when considering implementation in the combustion plants.

  7. A pilot survey of the U.S. medical waste industry to determine training needs for safely handling highly infectious waste.

    Science.gov (United States)

    Le, Aurora B; Hoboy, Selin; Germain, Anne; Miller, Hal; Thompson, Richard; Herstein, Jocelyn J; Jelden, Katelyn C; Beam, Elizabeth L; Gibbs, Shawn G; Lowe, John J

    2017-09-25

    The recent Ebola outbreak led to the development of Ebola virus disease (EVD) best practices in clinical settings. However, after the care of EVD patients, proper medical waste management and disposal was identified as a crucial component to containing the virus. Category A waste-contaminated with EVD and other highly infectious pathogens-is strictly regulated by governmental agencies, and led to only several facilities willing to accept the waste. A pilot survey was administered to determine if U.S. medical waste facilities are prepared to handle or transport category A waste, and to determine waste workers' current extent of training to handle highly infectious waste. Sixty-eight percent of survey respondents indicated they had not determined if their facility would accept category A waste. Of those that had acquired a special permit, 67% had yet to modify their permit since the EVD outbreak. This pilot survey underscores gaps in the medical waste industry to handle and respond to category A waste. Furthermore, this study affirms reports a limited number of processing facilities are capable or willing to accept category A waste. Developing the proper management of infectious disease materials is essential to close the gaps identified so that states and governmental entities can act accordingly based on the regulations and guidance developed, and to ensure public safety. Copyright © 2017 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Elsevier Inc. All rights reserved.

  8. Determination of estrogenic potential in waste water without sample extraction.

    Science.gov (United States)

    Avberšek, Miha; Žegura, Bojana; Filipič, Metka; Uranjek-Ževart, Nataša; Heath, Ester

    2013-09-15

    This study describes the modification of the ER-Calux assay for testing water samples without sample extraction (NE-(ER-Calux) assay). The results are compared to those obtained with ER-Calux assay and a theoretical estrogenic potential obtained by GC-MSD. For spiked tap and waste water samples there was no statistical difference between estrogenic potentials obtained by the three methods. Application of NE-(ER-Calux) to "real" influent and effluents from municipal waste water treatment plants and receiving surface waters found that the NE-(ER-Calux) assay gave higher values compared to ER-Calux assay and GC-MSD. This is explained by the presence of water soluble endocrine agonists that are usually removed during extraction. Intraday dynamics of the estrogenic potential of a WWTP influent and effluent revealed an increase in the estrogenic potential of the influent from 12.9 ng(EEQ)/L in the morning to a peak value of 40.0 ng(EEQ)/L in the afternoon. The estrogenic potential of the effluent was

  9. Determination of heat transfer coefficients in plastic French straws plunged in liquid nitrogen.

    Science.gov (United States)

    Santos, M Victoria; Sansinena, M; Chirife, J; Zaritzky, N

    2014-12-01

    The knowledge of the thermodynamic process during the cooling of reproductive biological systems is important to assess and optimize the cryopreservation procedures. The time-temperature curve of a sample immersed in liquid nitrogen enables the calculation of cooling rates and helps to determine whether it is vitrified or undergoes phase change transition. When dealing with cryogenic liquids, the temperature difference between the solid and the sample is high enough to cause boiling of the liquid, and the sample can undergo different regimes such as film and/or nucleate pool boiling. In the present work, the surface heat transfer coefficients (h) for plastic French straws plunged in liquid nitrogen were determined using the measurement of time-temperature curves. When straws filled with ice were used the cooling curve showed an abrupt slope change which was attributed to the transition of film into nucleate pool boiling regime. The h value that fitted each stage of the cooling process was calculated using a numerical finite element program that solves the heat transfer partial differential equation under transient conditions. In the cooling process corresponding to film boiling regime, the h that best fitted experimental results was h=148.12±5.4 W/m(2) K and for nucleate-boiling h=1355±51 W/m(2) K. These values were further validated by predicting the time-temperature curve for French straws filled with a biological fluid system (bovine semen-extender) which undergoes freezing. Good agreement was obtained between the experimental and predicted temperature profiles, further confirming the accuracy of the h values previously determined for the ice-filled straw. These coefficients were corroborated using literature correlations. The determination of the boiling regimes that govern the cooling process when plunging straws in liquid nitrogen constitutes an important issue when trying to optimize cryopreservation procedures. Furthermore, this information can lead to

  10. Determining national greenhouse gas emissions from waste-to-energy using the Balance Method.

    Science.gov (United States)

    Schwarzböck, Therese; Rechberger, Helmut; Cencic, Oliver; Fellner, Johann

    2016-03-01

    Different directives of the European Union require operators of waste-to-energy (WTE) plants to report the amount of electricity that is produced from biomass in the waste feed, as well as the amount of fossil CO2 emissions generated by the combustion of fossil waste materials. This paper describes the application of the Balance Method for determining the overall amount of fossil and thus climate relevant CO2 emissions from waste incineration in Austria. The results of 10 Austrian WTE plants (annual waste throughput of around 2,300 kt) demonstrate large seasonal variations in the specific fossil CO2 emissions of the plants as well as large differences between the facilities (annual means range from 32±2 to 51±3 kg CO(2,foss)/GJ heating value). An overall amount of around 924 kt/yr of fossil CO2 for all 10 WTE plants is determined. In comparison biogenic (climate neutral) CO2 emissions amount to 1,187 kt/yr, which corresponds to 56% of the total CO2 emissions from waste incineration. The total energy input via waste feed to the 10 facilities is about 22,500 TJ/yr, of which around 48% can be assigned to biogenic and thus renewable sources. Copyright © 2016 Elsevier Ltd. All rights reserved.

  11. PLASTIC WASTE CONVERSION TO LIQUID FUELS OVER MODIFIED-RESIDUAL CATALYTIC CRACKING CATALYSTS: MODELING AND OPTIMIZATION USING HYBRID ARTIFICIAL NEURAL NETWORK – GENETIC ALGORITHM

    Directory of Open Access Journals (Sweden)

    Istadi Istadi

    2012-04-01

    Full Text Available The plastic waste utilization can be addressed toward different valuable products. A promising technology for the utilization is by converting it to fuels. Simultaneous modeling and optimization representing effect of reactor temperature, catalyst calcinations temperature, and plastic/catalyst weight ratio toward performance of liquid fuel production was studied over modified catalyst waste. The optimization was performed to find optimal operating conditions (reactor temperature, catalyst calcination temperature, and plastic/catalyst weight ratio that maximize the liquid fuel product. A Hybrid Artificial Neural Network-Genetic Algorithm (ANN-GA method was used for the modeling and optimization, respectively. The variable interaction between the reactor temperature, catalyst calcination temperature, as well as plastic/catalyst ratio is presented in surface plots. From the GC-MS characterization, the liquid fuels product was mainly composed of C4 to C13 hydrocarbons.KONVERSI LIMBAH PLASTIK MENJADI BAHAN BAKAR CAIR DENGAN METODE PERENGKAHAN KATALITIK MENGGUNAKAN KATALIS BEKAS YANG TERMODIFIKASI: PEMODELAN DAN OPTIMASI MENGGUNAKAN GABUNGAN METODE ARTIFICIAL NEURAL NETWORK DAN GENETIC ALGORITHM. Pemanfaatan limbah plastik dapat dilakukan untuk menghasilkan produk yang lebih bernilai tinggi. Salah satu teknologi yang menjanjikan adalah dengan mengkonversikannya menjadi bahan bakar. Permodelan, simulasi dan optimisasi simultan yang menggambarkan efek dari suhu reaktor, suhu kalsinasi katalis, dan rasio berat plastik/katalis terhadap kinerja produksi bahan bakar cair telah dipelajari menggunakan katalis bekas termodifikasi Optimisasi ini ditujukan untuk mencari kondisi operasi optimum (suhu reaktor, suhu kalsinasi katalis, dan rasio berat plastik/katalis yang memaksimalkan produk bahan bakar cair. Metode Hybrid Artificial Neural Network-Genetic Algorithm (ANN-GA telah digunakan untuk permodelan dan optimisasi simultan tersebut. Inetraksi antar variabel

  12. Waste Tank Size Determination for the Hanford River Protection Project Cold Test, Training, and Mockup Facility

    Energy Technology Data Exchange (ETDEWEB)

    Onishi, Yasuo; Wells, Beric E.; Kuhn, William L.

    2001-03-30

    The objective of the study was to determine the minimum tank size for the Cold Test Facility process testing of Hanford tank waste. This facility would support retrieval of waste in 75-ft-diameter DSTs with mixer pumps and SSTs with fluidic mixers. The cold test model will use full-scale mixer pumps, transfer pumps, and equipment with simulated waste. The study evaluated the acceptability of data for a range of tank diameters and depths and included identifying how the test data would be extrapolated to predict results for a full-size tank.

  13. Indirect Determination of Chemical Composition and Fuel Characteristics of Solid Waste

    DEFF Research Database (Denmark)

    Riber, Christian; Christensen, Thomas Højlund

    Determination of chemical composition of solid waste can be performed directly or indirectly by analysis of combustion products. The indirect methodology instrumented by a full scale incinerator is the only method that can conclude on elements in trace concentrations. These elements are of great...... interest in evaluating waste management options by for example LCA modeling. A methodology description of indirect determination of chemical composition and fuel properties of waste is provided and validated by examples. Indirect analysis of different waste types shows that the chemical composition...... of toxic elements is shown exemplified by Hg. The average concentration is evaluated to be affected by three occurrences; background, rare items and very rare items (1/800 tonnes), that are all important to the Hg average concentration....

  14. Climate change and temperature-dependent sex determination: can individual plasticity in nesting phenology prevent extreme sex ratios?

    Science.gov (United States)

    Schwanz, Lisa E; Janzen, Fredric J

    2008-01-01

    Under temperature-dependent sex determination (TSD), temperatures experienced by embryos during development determine the sex of the offspring. Consequently, populations of organisms with TSD have the potential to be strongly impacted by climatic warming that could bias offspring sex ratio, a fundamental demographic parameter involved in population dynamics. Moreover, many taxa with TSD are imperiled, so research on this phenomenon, particularly long-term field study, has assumed great urgency. Recently, turtles with TSD have joined the diverse list of taxa that have demonstrated population-level changes in breeding phenology in response to recent climate change. This raises the possibility that any adverse impacts of climate change on populations may be alleviated by individual plasticity in nesting phenology. Here, we examine data from a long-term study on a population of painted turtles (Chrysemys picta) to determine whether changes in phenology are due to individual plasticity and whether individual plasticity in the timing of nesting has the capacity to offset the sex ratio effects of a rise in climatic temperature. We find that individual females show plasticity in the date of first nesting each year, and that this plasticity depends on the climate from the previous winter. First nesting date is not repeatable within individuals, suggesting that it would not respond to selection. Sex ratios of hatchlings within a nest declined nonsignificantly over the nesting season. However, small increases in summer temperature had a much stronger effect on nest sex ratios than did laying nests earlier in the season. For this and other reasons, it seems unlikely that individual plasticity in the timing of nesting will offset the effects of climate change on sex ratios in this population, and we hypothesize that this conclusion applies to other populations with TSD.

  15. 农业废弃物纤维/废旧塑料制备复合板材的研制%Development of agricultural waste fiber/waste plastic composite sheet

    Institute of Scientific and Technical Information of China (English)

    闫晗

    2011-01-01

    Agricultural waste fiber/waste plastic composite sheet was prepared by use of pretreatment of wood flour, rice bran and straw with recycle plastic (mainly HDPE). The affects of different processing methods on mechanical properties of composite sheet were investigated. The results showed that mechanical peeling treatment of agricultural waste can improve the mechanical properties of composite sheet; wood flour improves the tensile properties of the composite sheet,and the contribution effect of straw on the impact strength of composite sheet is obvious.%利用木粉、稻糠、秸秆等农业废弃物天然纤维与废旧塑料(主体为HDPE)制备复合板材,研究了不同机械处理方法对复合板材力学性能的影响.结果表明,机械剥离处理的农业废弃物能有效提高复合板材的力学性能;木粉对复合板材拉伸性能的提高作用明显,而秸秆对复合板材的冲击强度贡献明显.

  16. Radiochemical separation of actinides for their determination in environmental samples and waste products

    Energy Technology Data Exchange (ETDEWEB)

    Gleisberg, B. [Nuclear Engineering and Analytics Rossendorf, Inc. (VKTA), Dresden (Germany)

    1997-03-01

    The determination of low level activities of actinides in environmental samples and waste products makes high demands on radiochemical separation methods. Artificial and natural actinides were analyzed in samples form the surrounding areas of NPP and of uranium mines, incorporation samples, solutions containing radioactive fuel, solutions and solids resutling from the process, and in wastes. The activities are measured by {alpha}-spectrometry and {gamma}-spectrometry. (DG)

  17. Material recycling of post-consumer polyolefin bulk plastics: Influences on waste sorting and treatment processes in consideration of product qualities achievable.

    Science.gov (United States)

    Pfeisinger, Christian

    2017-02-01

    Material recycling of post-consumer bulk plastics made up of polyolefins is well developed. In this article, it is examined which effects on waste sorting and treatment processes influence the qualities of polyolefin-recyclats. It is shown that the properties and their changes during the product life-cycle of a polyolefin are defined by its way of polymerisation, its nature as a thermoplast, additives, other compound and composite materials, but also by the mechanical treatments during the production, its use where contact to foreign materials is possible and the waste sorting and treatment processes. Because of the sum of the effects influencing the quality of polyolefin-recyclats, conclusions are drawn for the material recycling of polyolefins to reach high qualities of their recyclats. Also, legal requirements like the EU regulation 1907/2006 concerning the registration, evaluation, authorisation and restrictions on chemicals are considered.

  18. A new numerical method for determining collapse load-carrying capacity of structure made of elasto-plastic material

    Institute of Scientific and Technical Information of China (English)

    钟志鹏; 任大龙; 万水

    2014-01-01

    Determination of collapse load-carrying capacity of elasto-plastic material is very important in designing structure. The problem is commonly solved by elasto-plastic finite element method (FEM). In order to deal with material nonlinear problem involving strain softening problem effectively, a new numerical method-damped Newton method was proposed. The iterative schemes are discussed in detail for pure equilibrium models. In the equilibrium model, the plasticity criterion and the compatibility of the strains are verified, and the strain increment and plastic factor are treated as independent unknowns. To avoid the stiffness matrix being singularity or condition of matrix being ill, a damping factor α was introduced to adjust the value of plastic consistent parameter automatically during the iterations. According to the algorithm, the nonlinear finite element program was complied and its numerical example was calculated. The numerical results indicate that this method converges very fast for both small load steps and large load steps. Compared with those results obtained by analysis and experiment, the predicted ultimate bearing capacity from the proposed method is identical.

  19. Determination of the Structure of Vitrified Hydroceramic/CBC Waste Form Glasses Manufactured from DOE Reprocessing Waste

    Energy Technology Data Exchange (ETDEWEB)

    Scheetz, B.E.; White, W. B.; Chesleigh, M.; Portanova, A.; Olanrewaju, J.

    2005-05-31

    The selection of a glass-making option for the solidification of nuclear waste has dominated DOE waste form programs since the early 1980's. Both West Valley and Savannah River are routinely manufacturing glass logs from the high level waste inventory in tank sludges. However, for some wastes, direct conversion to glass is clearly not the optimum strategy for immobilization. INEEL, for example, has approximately 4400 m{sup 3} of calcined high level waste with an activity that produces approximately 45 watts/m{sup 3}, a rather low concentration of radioactive constituents. For these wastes, there is value in seeking alternatives to glass. An alternative approach has been developed and the efficacy of the process demonstrated that offers a significant savings in both human health and safety exposures and also a lower cost relative to the vitrification option. The alternative approach utilizes the intrinsic chemical reactivity of the highly alkaline waste with the addition of aluminosilicate admixtures in the appropriate proportions to form zeolites. The process is one in which a chemically bonded ceramic is produced. The driving force for reaction is derived from the chemical system itself at very modest temperatures and yet forms predominantly crystalline phases. Because the chemically bonded ceramic requires an aqueous medium to serve as a vehicle for the chemical reaction, the proposed zeolite-containing waste form can more adequately be described as a hydroceramic. The hydrated crystalline materials are then subject to hot isostatic pressing (HIP) which partially melts the material to form a glass ceramic. The scientific advantages of the hydroceramic/CBC approach are: (1) Low temperature processing; (2) High waste loading and thus only modest volumetric bulking from the addition of admixtures; (3) Ability to immobilize sodium; (4) Ability to handle low levels of nitrate (2-3% NO{sub 3}{sup -}); (5) The flexibility of a vitrifiable waste; and (6) A process

  20. The selective recycling of mixed plastic waste of polylactic acid and polyethylene terephthalate by control of process conditions

    OpenAIRE

    Carné Sánchez , Arnau; Collinson, Simon R.

    2011-01-01

    The glycolysis of postconsumer polyethylene terephthalate (PET) waste was evaluated with catalysts of zinc acetate, zinc stearate and zinc sulfate, showing that zinc acetate was the most soluble and effective. The chemical recycling by solvolysis of polylactic acid (PLA) and PET waste in either methanol or ethanol was investigated. Zinc acetate as a catalyst was found to be necessary to yield an effective depolymerization of waste PLA giving lactate esters, while with the same reaction condit...

  1. Comparison of leaching tests to determine and quantify the release of inorganic contaminants in demolition waste.

    Science.gov (United States)

    Delay, Markus; Lager, Tanja; Schulz, Horst D; Frimmel, Fritz H

    2007-01-01

    The changes in waste management policy caused by the massive generation of waste materials (e.g. construction and demolition waste material, municipal waste incineration products) has led to an increase in the reuse and recycling of waste materials. For environmental risk assessment, test procedures are necessary to examine waste materials before they can be reused. In this article, results of column and lysimeter leaching tests having been applied to inorganic compounds in a reference demolition waste material are presented. The results show a good agreement between the leaching behaviour determined with the lysimeter unit and the column units used in the laboratory. In view of less time and system requirements compared to lysimeter systems, laboratory column units can be considered as a practicable instrument to assess the time-dependent release of inorganic compounds under conditions similar to those encountered in a natural environment. The high concentrations of elements in the seepage water at the initial stage of elution are reflected by the laboratory column leaching tests. In particular, authorities or laboratories might benefit and have an easy-to-use, but nevertheless reliable, method to serve as a basis for decision-making.

  2. Flow-Injection Amperometric Determination of Tacrine based on Ion Transfer across a Water–Plasticized Polymeric Membrane Interface

    OpenAIRE

    Rueda, C.; Joaquin A. Ortuño

    2007-01-01

    A flow-injection pulse amperometric method for determining tacrine, based on ion transfer across a plasticized poly(vinyl chloride) (PVC) membrane, was developed. A four-electrode potentiostat with ohmic drop compensation was used, while a flow-through cell incorporated the four electrodes and the membrane, which contained tetrabutylammonium tetraphenylborate. The influence of the applied potential and of the flow-injection variables on the determination of tacrine was studied. In the selecte...

  3. 40 CFR 262.212 - Making the hazardous waste determination at an on-site interim status or permitted treatment...

    Science.gov (United States)

    2010-07-01

    ....212 Making the hazardous waste determination at an on-site interim status or permitted treatment... hazardous waste permit or interim status as soon as it arrives in the on-site treatment, storage or disposal... permitted treatment, storage or disposal facility. (e) If the unwanted material is a hazardous waste, the...

  4. 废旧线路板中塑料的回收及利用%Recycling and Reusing of Plastic in Waste Printed Circuit Board

    Institute of Scientific and Technical Information of China (English)

    李启胜

    2012-01-01

    总结了废旧线路板中塑料的回收处置方法和废旧线路板中塑料的回收利用现状.重点介绍了废旧线路板中塑料的物理回收法、热解回收法和溶液回收法,在综合比较废旧线路板中塑料回收利用的各种方法的基础上展望了废旧线路板中塑料回收利用的发展趋势.%The recycling technology and comprehensive application-situation of plastic in waste printed circuit board were summarized, and the physical recovery method, pyrolysis recovery method and solution recovery method were mainly introduced. On the basis of comprehensive comparing of the recycling methods, the recyling trends of plastic in waste printed circuit board was prospected.

  5. Direct probe atmospheric pressure photoionization/atmospheric pressure chemical ionization high-resolution mass spectrometry for fast screening of flame retardants and plasticizers in products and waste.

    Science.gov (United States)

    Ballesteros-Gómez, A; Brandsma, S H; de Boer, J; Leonards, P E G

    2014-04-01

    In this study, we develop fast screening methods for flame retardants and plasticizers in products and waste based on direct probe (DP) atmospheric pressure photoionization (APPI) and atmospheric pressure chemical ionization (APCI) coupled to a high-resolution (HR) time-of-flight mass spectrometer. DP-APPI is reported for the first time in this study, and DP-APCI that has been scarcely exploited is optimized for comparison. DP-APPI was more selective than DP-APCI and also more sensitive for the most hydrophobic compounds. No sample treatment was necessary, and only a minimal amount of sample (few milligrams) was used for analysis that was performed within a few minutes. Both methods were applied to the analysis of plastic products, electronic waste, and car interiors. Polybrominated diphenylethers, new brominated flame retardants, and organophosphorus flame retardants were present in most of the samples. The combination of DP with HR mass spectra and data processing based on mass accuracy and isotopic patterns allowed the unambiguous identification of chemicals at low levels of about 0.025 % (w/w). Under untargeted screening, resorcinol bis(biphenylphosphate) and bisphenol A bis(bisphenylphosphate) were identified in many of the consumer products of which literature data are still very limited.

  6. Some exploitation properties of wood plastic composites (WPC), based on high density polyethylene and timber industry waste

    OpenAIRE

    janis kajaks

    2015-01-01

    Abstract: In this study, the influence of wood fiber content (40, 50 and 60 wt.%) and coupling agent concentration (3 and 5 wt.%) on the mechanical properties of wood-plastic composites (WPCs) was investigated. Two types of plastic (high-density-polyethylene (HDPE) and recycled high-density-polyethylene (rHDPE)) were used as polymer matrices for preparing WPC. As reinforcement, prior grinded (fiber length < 0.5 mm) coniferous wood shavings were utilized. Overall trend showed, that by addin...

  7. Foraging modality and plasticity in foraging traits determine the strength of competitive interactions among carnivorous plants, spiders and toads.

    Science.gov (United States)

    Jennings, David E; Krupa, James J; Rohr, Jason R

    2016-07-01

    Foraging modalities (e.g. passive, sit-and-wait, active) and traits are plastic in some species, but the extent to which this plasticity affects interspecific competition remains unclear. Using a long-term laboratory mesocosm experiment, we quantified competition strength and the plasticity of foraging traits in a guild of generalist predators of arthropods with a range of foraging modalities. Each mesocosm contained eight passively foraging pink sundews, and we employed an experimental design where treatments were the presence or absence of a sit-and-wait foraging spider and actively foraging toad crossed with five levels of prey abundance. We hypothesized that actively foraging toads would outcompete the other species at low prey abundance, but that spiders and sundews would exhibit plasticity in foraging traits to compensate for strong competition when prey were limited. Results generally supported our hypotheses. Toads had a greater effect on sundews at low prey abundances, and toad presence caused spiders to locate webs higher above the ground. Additionally, the closer large spider webs were to the ground, the greater the trichome densities produced by sundews. Also, spider webs were larger with than without toads and as sundew numbers increased, and these effects were more prominent as resources became limited. Finally, spiders negatively affected toad growth only at low prey abundance. These findings highlight the long-term importance of foraging modality and plasticity of foraging traits in determining the strength of competition within and across taxonomic kingdoms. Future research should assess whether plasticity in foraging traits helps to maintain coexistence within this guild and whether foraging modality can be used as a trait to reliably predict the strength of competitive interactions. © 2016 The Authors. Journal of Animal Ecology © 2016 British Ecological Society.

  8. The criteria weight determination of factors impacting the melt flow index of degradable plastics using Lambda-Max method

    Science.gov (United States)

    Dom, Rosma Mohd; Saadon, Nurul Adzlyana; Mohamad, Daud

    2013-09-01

    Three common methods of determining criteria weights using the Analytic Hierarchy Process (AHP) are extent analysis, logarithmic least square method (LLSM) and Lambda-Max. Lambda-Max criteria weights determination method uses pair wise comparison of criteria considered. Studies have shown that Lambda-Max is a preferred criteria weight determination method since it involves lesser computation with consistent results of precise criteria weights generated. In this paper the criteria weights of four factors impacting the Melt Flow Index of degradable plastics are calculated using Lambda-Max method. The input factors (criteria) are the percentages by mass of polyethylene, oil palm biomass, palm olein and starch used in the formulation of degradable plastics. The criteria weights are calculated using Lambda-Max based on input given by four experts. The finding indicates the feasibility of using Lambda-Max method in criteria weight determination for determining the impact of four factors in the formulation of degradable plastics as reflected by the consistency control index value calculated.

  9. 废塑料基复合材料粉体法综合回收技术%Comprehensive Recovery Technology of Waste Plastic Matrix Composites

    Institute of Scientific and Technical Information of China (English)

    张丽

    2014-01-01

    The relevant technologies for recycling waste plastic matrix composites at home and abroad were introduced. According to the characteristics of waste plastic matrix composites, mechanical crushing, dissociation (large breaking, breaking, crushing dissociation), high-voltage electrostatic separation methods were used for recycling composite materials. The purity of recovered metal (such as aluminum) was more than 99%,metal (aluminum) recovery was more than 99%,too.The purity of recycled plastic was more than 96%. These data were close to or above the level of similar foreign technology. The recycling process did not use any chemicals and water, did not discharge any pollutants.%介绍了国内外对废塑料基复合材料回收技术的相关现状,根据废塑料基复合材料的特点采用机械粉碎、解离(大型破碎、中碎、粉碎解离)、高压静电分选的方法回收废塑料复合材料,回收金属(铝等)的纯度达99%以上;金属(铝等)回收率达99%以上;回收塑料的纯度达96%以上,接近甚至超过国外同类技术的水平。在回收过程中不使用任何化工原料,不使用水,不排放任何污染物。

  10. 废塑料入炉喷吹的数值模拟研究%Numerical simulation of waste plastic injection in blast furnace

    Institute of Scientific and Technical Information of China (English)

    董树; 史岩彬; 耿啸

    2016-01-01

    基于高炉喷吹混合燃料的方法,探究废塑料作为燃料在高炉内的作用。以某2536 m3高炉为研究对象,将喷入的煤粉及塑料作为粉相,分析混合燃料的水分、灰分、挥发分和固定碳等化学指标,采用高炉高温区热平衡分析法,计算高炉单一喷吹和混合喷吹条件下的焦比,对高炉内喷吹过程进行模拟研究。计算机模拟结果表明,将煤粉与废塑料混合喷吹降低了高炉焦比,提高了煤的利用率。%Based on the method of blast furnace injection the mixing fuel , the effect of waste plastics as fuel in blast furnace injection was explored .The 2536 m3 blast furnace as an example , considering the pulverized coals and plastics as powder phase , moisture, ash, volatile and fixed carbon etc .The high temperature zone of blast furnace heat balance analysis method was used to calculate the coke ratio of single injection and mixing injection , and the process of blast furnace injection was studied .Com-puter simulation results show that the mixture injection of pulverized coal and waste plastic reduce coke ratio and improve the utilization rate of coal .

  11. 榆树市农田废膜捡拾机选型及推广对策%Countermeasure Study of Selection and Promotion of Farmland Waste Plastic Film Collecting Machine in Yushu City

    Institute of Scientific and Technical Information of China (English)

    王珏; 蒋福娟; 郭玉红; 王晓峰

    2015-01-01

    地膜覆盖栽培技术可明显提高土地产出能力和农作物产量,但废膜的年积月累却带来了严重的环境污染和土地损伤。推广废膜捡拾机械化技术可有效防治农田“白色污染”。为此,还须政府给予政策扶持,大力推广适用的废膜回收机械,特别是要重视废膜回收的再利用。%Plastic film mulching cultivation technology can significantly improve the capacity of land production and crop yield. However,the accumulation of wasted plastic film brings about serious consequences such as environment pollution and soil damage. Promoting the technology of wasted plastic film picking mechanization can effectively prevent 'White Pollution' in farmland. Therefore,the government should make supporting policies to promote proper wasted plastic film collecting machines, especially attach importance to the recycling of wasted plastic film.

  12. New perspectives in plastic biodegradation.

    Science.gov (United States)

    Sivan, Alex

    2011-06-01

    During the past 50 years new plastic materials, in various applications, have gradually replaced the traditional metal, wood, leather materials. Ironically, the most preferred property of plastics--durability--exerts also the major environmental threat. Recycling has practically failed to provide a safe solution for disposal of plastic waste (only 5% out of 1 trillion plastic bags, annually produced in the US alone, are being recycled). Since the most utilized plastic is polyethylene (PE; ca. 140 million tons/year), any reduction in the accumulation of PE waste alone would have a major impact on the overall reduction of the plastic waste in the environment. Since PE is considered to be practically inert, efforts were made to isolate unique microorganisms capable of utilizing synthetic polymers. Recent data showed that biodegradation of plastic waste with selected microbial strains became a viable solution. Copyright © 2011 Elsevier Ltd. All rights reserved.

  13. Determination of Adsorption of Diesel onto a Poultry Waste: Chicken Feather

    Directory of Open Access Journals (Sweden)

    *Kelle, H. I

    2015-06-01

    Full Text Available Chicken feather is a poultry waste. With the recent development of waste management strategy viz; waste recycle, re-use and waste reduction e.t.c., chicken feather has been put to various uses such as in the production of animal feed, organic fertilizer, biodegradable plastic and others. It has been mentioned in some text/resource that chicken feather can be used to mop oil spill. However, there is scarce literature on the mopping account of hydrocarbon oil by chicken feather. This led to the study. In this study the equilibrium adsorption capacity (qe of diesel onto chicken feather, the amount of adsorbed diesel recovered from chicken feather and the amount of diesel retained by chicken feather was determined by simple kinetic studies and compared with that of a conventional synthetic sorbent used in mopping oil spill in the oil industry. This conventional synthetic sorbent served as standard. Both sorbents were compared under the same experimental condition and the experiment was carried out at room temperature 290 C. Linearized adsorption isotherms of Langmuir, Freundlich, Elovich, Temkin and Dubinin-Radushkevich were used to verify the adsorption process of both sorbents. The result of the study shows that the equilibrium adsorption capacity (qe of diesel onto chicken feather is 11.04g/g, the time required to attain equilibrium adsorption is 80 minutes, while that of the standard is 10.20g/g at 60 minutes. This shows that chicken feather has a higher adsorption capacity. The best fitting isotherm for the adsorption process of both sorbents is the linearized form Ce/qe versus Ce of the Langmuir adsorption isotherm with coefficient of determination (r2 of 0.999 for both sorbents (chicken feather and standard. The validity of Langmuir model was check by calculating the average percentage error (APE %. The APE values obtained for chicken feather and standard are 0.0024 and 0.005 respectively. The low APE values show that Langmuir model is valid

  14. Polybrominated diphenyl ethers (PBDEs) and heavy metals in road dusts from a plastic waste recycling area in north China: implications for human health.

    Science.gov (United States)

    Tang, Zhenwu; Huang, Qifei; Yang, Yufei; Nie, Zhiqiang; Cheng, Jiali; Yang, Jun; Wang, Yuwen; Chai, Miao

    2016-01-01

    Road dusts were collected from an area where intense mechanical recycling of plastic wastes occurs in Wen'an, north China. These dusts were investigated for polybrominated diphenyl ethers (PBDEs) and heavy metals contamination to assess the health risk related to these components. Decabromodiphenyl ether (BDE-209) and Σ21PBDE concentrations in these dusts ranged from 2.67 to 10,424 ng g(-1) and from 3.23 to 10,640 ng g(-1), respectively. These PBDE concentrations were comparable to those observed in road dust from e-waste recycling areas but were 1-2 orders of magnitude higher than concentrations in outdoor or road dusts from other areas. This indicates that road dusts in the study area have high levels of PBDE pollution. BDE-209 was the predominant congener, accounting for 86.3% of the total PBDE content in dusts. Thus, commercial deca-BDE products were the dominant source. The average concentrations of As, Cd, Cr, Cu, Hg, Pb, Sb, and Zn in these same dust samples were 10.1, 0.495, 112, 54.7, 0.150, 71.8, 10.6, and 186 mg kg(-1), respectively. The geoaccumulation index suggests that road dusts in this area are moderately to heavily polluted with Cd, Hg, and Sb. This study shows that plastic waste processing is a major source of toxic pollutants in road dusts in this area. Although the health risk from exposure to dust PBDEs was low, levels of some heavy metals in this dust exceeded acceptable risk levels for children and are of great concern.

  15. Plastic value chains

    DEFF Research Database (Denmark)

    Baxter, John; Wahlstrom, Margareta; Zu Castell-Rüdenhausen, Malin

    2014-01-01

    Optimizing plastic value chains is regarded as an important measure in order to increase recycling of plastics in an efficient way. This can also lead to improved awareness of the hazardous substances contained in plastic waste, and how to avoid that these substances are recycled. As an example......, plastics from WEEE is chosen as a Nordic case study. The project aims to propose a number of improvements for this value chain together with representatives from Nordic stakeholders. Based on the experiences made, a guide for other plastic value chains shall be developed....

  16. Methods for determining the biomass content of waste.

    Science.gov (United States)

    Staber, Wolfgang; Flamme, Sabine; Feltner, Johann

    2008-02-01

    As CO2 emission trading in Europe has been established it is of essential importance to distinguish between biogenic and fossil emissions. Emissions resulting from bio-fuels and biogenous fractions are categorized as climate-neutral. Determination of plants using only fossil or bio-fuels is simple but categorization becomes more difficult for plants using a mix of fossil and bio-fuel such as solid recovered fuels. In the meantime, different methods for solving this problem have been developed. Using different approaches and technologies, all of these methods have the same goal: determining the biomass content (biogenic fraction), for example, in solid recovered fuels or in the off-gas of a mono- or co-incineration plant in order to calculate the biogenic carbon dioxide emissions. In the following article, the most common methods for determining the biogenic fraction of fuels, namely the Selective Dissolution Method, the Balance Method and the 14C-Method will be explained in detail.

  17. Social life and sanitary risks: evolutionary and current ecological conditions determine waste management in leaf-cutting ants

    Science.gov (United States)

    Farji-Brener, Alejandro G.; Elizalde, Luciana; Amador-Vargas, Sabrina

    2016-01-01

    Adequate waste management is vital for the success of social life, because waste accumulation increases sanitary risks in dense societies. We explored why different leaf-cutting ants (LCA) species locate their waste in internal nest chambers or external piles, including ecological context and accounting for phylogenetic relations. We propose that waste location depends on whether the environmental conditions enhance or reduce the risk of infection. We obtained the geographical range, habitat and refuse location of LCA from published literature, and experimentally determined whether pathogens on ant waste survived to the high soil temperatures typical of xeric habitats. The habitat of the LCA determined waste location after phylogenetic correction: species with external waste piles mainly occur in xeric environments, whereas those with internal waste chambers mainly inhabit more humid habitats. The ancestral reconstruction suggests that dumping waste externally is less derived than digging waste nest chambers. Empirical results showed that high soil surface temperatures reduce pathogen prevalence from LCA waste. We proposed that LCA living in environments unfavourable for pathogens (i.e. xeric habitats) avoid digging costs by dumping the refuse above ground. Conversely, in environments suitable for pathogens, LCA species prevent the spread of diseases by storing waste underground, presumably, a behaviour that contributed to the colonization of humid habitats. These results highlight the adaptation of organisms to the hygienic challenges of social living, and illustrate how sanitary behaviours can result from a combination of evolutionary history and current environmental conditions. PMID:27226469

  18. Laboratory-Scale Melter for Determination of Melting Rate of Waste Glass Feeds

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Dong-Sang; Schweiger, Michael J.; Buchmiller, William C.; Matyas, Josef

    2012-01-09

    The purpose of this study was to develop the laboratory-scale melter (LSM) as a quick and inexpensive method to determine the processing rate of various waste glass slurry feeds. The LSM uses a 3 or 4 in. diameter-fused quartz crucible with feed and off-gas ports on top. This LSM setup allows cold-cap formation above the molten glass to be directly monitored to obtain a steady-state melting rate of the waste glass feeds. The melting rate data from extensive scaled-melter tests with Hanford Site high-level wastes performed for the Hanford Tank Waste Treatment and Immobilization Plant have been compiled. Preliminary empirical model that expresses the melting rate as a function of bubbling rate and glass yield were developed from the compiled database. The two waste glass feeds with most melter run data were selected for detailed evaluation and model development and for the LSM tests so the melting rates obtained from LSM tests can be compared with those from scaled-melter tests. The present LSM results suggest the LSM setup can be used to determine the glass production rates for the development of new glass compositions or feed makeups that are designed to increase the processing rate of the slurry feeds.

  19. Comparison between students and residents on determinants of willingness to separate waste and waste separation behaviour in Zhengzhou, China.

    Science.gov (United States)

    Dai, Xiaoping; Han, Yuping; Zhang, Xiaohong; Hu, Wei; Huang, Liangji; Duan, Wenpei; Li, Siyi; Liu, Xiaolu; Wang, Qian

    2017-09-01

    A better understanding of willingness to separate waste and waste separation behaviour can aid the design and improvement of waste management policies. Based on the intercept questionnaire survey data of undergraduate students and residents in Zhengzhou City of China, this article compared factors affecting the willingness and behaviour of students and residents to participate in waste separation using two binary logistic regression models. Improvement opportunities for waste separation were also discussed. Binary logistic regression results indicate that knowledge of and attitude to waste separation and acceptance of waste education significantly affect the willingness of undergraduate students to separate waste, and demographic factors, such as gender, age, education level, and income, significantly affect the willingness of residents to do so. Presence of waste-specific bins and attitude to waste separation are drivers of waste separation behaviour for both students and residents. Improved education about waste separation and facilities are effective to stimulate waste separation, and charging on unsorted waste may be an effective way to improve it in Zhengzhou.

  20. Determination of heavy metal toxicity of finished leather solid waste.

    Science.gov (United States)

    Aslan, Ahmet

    2009-05-01

    This paper investigates the toxicity in leather products of heavy metals known to be detrimental to the ecosystem. Heavy metal concentrations in leather samples were identified with ICP-OES, and toxicity was determined using a MetPLATE bioassay. Chromium and aluminium were found to constitute 98% of the total concentration of heavy metals in finished leather tanned with chromium and aluminium salts, while in some vegetable-tanned leather, zirconium was the only heavy metal identified. The average inhibition values for chromium, aluminium and vegetable tanned leather were 98.08%, 97.04% and 62.36%, respectively.

  1. Characterization of hospital waste in Lahore, Pakistan

    Institute of Scientific and Technical Information of China (English)

    Sobia Munir; Syeda Adila Batool; Muhammad Nawaz Chaudhry

    2014-01-01

    Background It is a common practice in developing countries that medical/infectious waste openly dumped with municipal solid waste.This paper presented a generation and characterization study of hospital waste.Determination of the waste composition is a basic step for selecting the most efficient treatment method of hospital waste.Methods Stratified random sampling was used to collect the samples of general as well as medical wastes for seven days.Medical waste was sorted into 10 categories whereas general waste was classified into 11 categories.Incineration was observed thoroughly for observing flaws in the incineration process.Data was analyzed by using SPSS software version 16.0.Results The studied hospital produced an average 297 kilograms of medical waste daily and it comprises plastics (71.0%),glass (13.9%),papers etc.(3.8%),cotton/dressings (5.7%),masks/gloves/sheets (0.3%) diapers (0.4%),wasted machines used in operation theaters (2.0%) and blades (0.1%).Laboratories,cancer ward,nursery ward,OPD and emergency ward are the largest infectious waste producing departments in the hospital.The hospital produced an average 3 511 kilograms of general waste daily in which organics constitute (44.3%),diapers etc.(42.8%),demolition materials (3.7%),plastic waste mixing medical plastic waste (2.5%),miscellaneous (2.14%),cloth/clothes (1.6%),cardboard (1.3%),papers (0.8%),cotton dressings (0.28%),glass (0.27%) and iron materials (0.18%).Other alarming facts are:medical waste is recycled in study area,after incineration of hospital waste,ash simply dumped in the premises of the hospital without any liner system.Conclusions The studied hospital produces 10% of infectious waste and 90% of general waste.The largest components of the infectious waste are plastic and glass.Organics and diapers are major components of the general waste coming from different sites of the hospital.Lack of training,inadequate knowledge regarding to the

  2. Experimental Determination and Thermodynamic Modeling of Electrical Conductivity of SRS Waste Tank Supernate

    Energy Technology Data Exchange (ETDEWEB)

    Pike, J. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Reboul, S. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2015-06-01

    SRS High Level Waste Tank Farm personnel rely on conductivity probes for detection of incipient overflow conditions in waste tanks. Minimal information is available concerning the sensitivity that must be achieved such that that liquid detection is assured. Overly sensitive electronics results in numerous nuisance alarms for these safety-related instruments. In order to determine the minimum sensitivity required of the probe, Tank Farm Engineering personnel need adequate conductivity data to improve the existing designs. Little or no measurements of liquid waste conductivity exist; however, the liquid phase of the waste consists of inorganic electrolytes for which the conductivity may be calculated. Savannah River Remediation (SRR) Tank Farm Facility Engineering requested SRNL to determine the conductivity of the supernate resident in SRS waste Tank 40 experimentally as well as computationally. In addition, SRNL was requested to develop a correlation, if possible, that would be generally applicable to liquid waste resident in SRS waste tanks. A waste sample from Tank 40 was analyzed for composition and electrical conductivity as shown in Table 4-6, Table 4-7, and Table 4-9. The conductivity for undiluted Tank 40 sample was 0.087 S/cm. The accuracy of OLI Analyzer™ was determined using available literature data. Overall, 95% of computed estimates of electrical conductivity are within ±15% of literature values for component concentrations from 0 to 15 M and temperatures from 0 to 125 °C. Though the computational results are generally in good agreement with the measured data, a small portion of literature data deviates as much as ±76%. A simplified model was created that can be used readily to estimate electrical conductivity of waste solution in computer spreadsheets. The variability of this simplified approach deviates up to 140% from measured values. Generally, this model can be applied to estimate the conductivity within a factor of two. The comparison of the

  3. Determination of the Specific Heat Ratio of a Gas in a Plastic Syringe

    Science.gov (United States)

    Chamberlain, Jeff

    2010-01-01

    The rapid compression or expansion of a gas in a plastic syringe is a poor approximation of an adiabatic process. Heat exchange with the walls of the syringe brings the gas to equilibrium in an amount of time that is not significantly greater than the length of the compression or expansion itself. Despite this limitation, it is still possible to…

  4. Determination of microstructural changes by severely plastically deformed copper-aluminum alloy: Optical study

    Directory of Open Access Journals (Sweden)

    Romčević N.

    2014-01-01

    Full Text Available Our work deals with the problem of producing a complex metal-ceramic composite using the processes of internal oxidation (IO and severe plastic deformation. For this purpose, Cu-Al alloy with 0.4wt.% of Al was used. IO of sample serves in the first step of the processing as a means for attaining a fine dispersion of nanosized oxide particles in the metal matrix. Production technology continues with repeated application of severe plastic deformation (SPD of the resulting metalmatrix composite to produce the bulk nanoscaled structural material. SPD was carried out with equal channel angular pressing (ECAP, which allowed that the material could be subjected to an intense plastic strain through simple shear. Microstructural characteristics of one phase and multiphase material was studied on internally oxidized Cu with 0.4wt.% of Al sample composed of one phase copper-aluminum solid solution in the core and fine dispersed oxide particles in the same matrix in the mantle region. In this manner AFM, X-ray diffraction and Raman spectroscopy were used. Local structures in plastically deformed samples reflect presence of Cu, CuO, Cu2O, Cu4O3 or Al2O3 structural characteristics, depending on type of sample. [Projekat Ministarstva nauke Republike Srbije, br. III45003

  5. Combined method of determining the thermal characteristics of solid wastes from combustible minerals

    Energy Technology Data Exchange (ETDEWEB)

    Belyaev, A.A.; Gulshnev, S.V.; Ignatova, N.N.

    1983-01-01

    A comparative method for determining the heat capacity and coefficient of thermal conductivity of materials from coal mining and processing wastes is substantiated theoretically. The basic scheme of an apparatus is given, and the limits of the application of the method and the accuracy of the measurements achievable at the present time are substantiated.

  6. Combined method of determining the thermal characteristics of solid wastes from combustible minerals

    Energy Technology Data Exchange (ETDEWEB)

    Belyaev, A.A.; Glushnev, S.V.; Ignatova, N.N.

    1983-01-01

    A theoretical background is provided for a comparative method used to determine the thermal capacitance and thermal conductivity of coal production and processing wastes. The apparatus is described, together with the limits of application of the method and the accuracy obtained to date. (6 refs.)

  7. Determination of tritium and carbon-14 in accelerator waste

    Energy Technology Data Exchange (ETDEWEB)

    Argentini, M.; Weinreich, R. [Lab. of Radio- and Environmental Chemistry, Paul Scherrer Inst., Villigen-PSI (Switzerland)

    2003-07-01

    In dismounted parts of the accelerator facilities of paul scherrer institute, tritium and {sup 14}C were determined by low-level counting after chemical separation. In graphite targets used for the production of {pi}-mesons, tritium amounts from 1.7.10{sup 8} to 6.10{sup 8} Bq/g were found; the corresponding {sup 14}C data were 6 and 9 Ci/g, respectively. In the dismantled copper beam dump of Target E, the tritium content extended up to 2.8.10{sup 6} Bq/g, but no {sup 14}C could be detected. In mechanical parts of the beam dump, consisting of iron and stainless steel, respectively, the tritium amount ranged up to 5.3.10{sup 3} Bq/g, the {sup 14}C amount from 1 to 800 Bq/g. The separation procedures are described in detail. (orig.)

  8. Biodegradation of plastics.

    Science.gov (United States)

    Shimao, M

    2001-06-01

    Widespread studies on the biodegradation of plastics have been carried out in order to overcome the environmental problems associated with synthetic plastic waste. Recent work has included studies of the distribution of synthetic polymer-degrading microorganisms in the environment, the isolation of new microorganisms for biodegradation, the discovery of new degradation enzymes, and the cloning of genes for synthetic polymer-degrading enzymes.

  9. Position for determining gas-phase volatile organic compound concentrations in transuranic waste containers. Revision 2

    Energy Technology Data Exchange (ETDEWEB)

    Connolly, M.J.; Liekhus, K.J. [Lockheed Martin Idaho Technologies Co., Idaho Falls, ID (United States). Idaho National Engineering and Environmental Lab.; Djordjevic, S.M.; Loehr, C.A.; Spangler, L.R. [Benchmark Environmental Corp. (United States)

    1998-06-01

    In the conditional no-migration determination (NMD) for the test phase of the Waste Isolation Pilot Plant (WIPP), the US Environmental Protection Agency (EPA) imposed certain conditions on the US Department of Energy (DOE) regarding gas phase volatile organic compound (VOC) concentrations in the void space of transuranic (TRU) waste containers. Specifically, the EPA required the DOE to ensure that each waste container has no layer of confinement that contains flammable mixtures of gases or mixtures of gases that could become flammable when mixed with air. The EPA also required that sampling of the headspace of waste containers outside inner layers of confinement be representative of the entire void space of the container. The EPA stated that all layers of confinement in a container would have to be sampled until DOE can demonstrate to the EPA that sampling of all layers is either unnecessary or can be safely reduced. A test program was conducted at the Idaho National Engineering and Environmental Laboratory (INEEL) to demonstrate that the gas phase VOC concentration in the void space of each layer of confinement in vented drums can be estimated from measured drum headspace using a theoretical transport model and that sampling of each layer of confinement is unnecessary. This report summarizes the studies performed in the INEEL test program and extends them for the purpose of developing a methodology for determining gas phase VOC concentrations in both vented and unvented TRU waste containers. The methodology specifies conditions under which waste drum headspace gases can be said to be representative of drum gases as a whole and describes a method for predicting drum concentrations in situations where the headspace concentration is not representative. The methodology addresses the approach for determining the drum VOC gas content for two purposes: operational period drum handling and operational period no-migration calculations.

  10. Effect of E-waste Recycling on Urinary Metabolites of Organophosphate Flame Retardants and Plasticizers and Their Association with Oxidative Stress.

    Science.gov (United States)

    Lu, Shao-You; Li, Yan-Xi; Zhang, Tao; Cai, Dan; Ruan, Ju-Jun; Huang, Ming-Zhi; Wang, Lei; Zhang, Jian-Qing; Qiu, Rong-Liang

    2017-02-21

    In this study, three chlorinated (Cl-mOPs) and five nonchlorinated (NCl-mOPs) organophosphate metabolites were determined in urine samples collected from participants living in an electronic waste (e-waste) dismantling area (n = 175) and two reference areas (rural, n = 29 and urban, n = 17) in southern China. Bis(2-chloroethyl) phosphate [BCEP, geometric mean (GM): 0.72 ng/mL] was the most abundant Cl-mOP, and diphenyl phosphate (DPHP, 0.55 ng/mL) was the most abundant NCl-mOP. The GM concentrations of mOPs in the e-waste dismantling sites were higher than those in the rural control site. These differences were significant for BCEP (p e-waste dismantling activities contributed to human exposure to OPs. In the e-waste sites, the urinary concentrations of bis(2-chloro-isopropyl) phosphate (r = 0.484, p e-waste dismantling areas. To our knowledge, this study is the first to report the urinary levels of mOPs in China and examine the association between OP exposure and 8-OHdG in humans.

  11. Laser Raman spectrometric determination of oxy-anions in nuclear waste materials

    Energy Technology Data Exchange (ETDEWEB)

    Miller, A.G.

    1977-03-01

    Oxy-anions in complex nuclear process-waste materials are being determined by laser Raman spectrometry (LRS). The double internal-standard technique developed by Marston is applied to the simultaneous determination of up to x anions in alkaline solutions. The method of Marston has been extended to solutions prepared from the solids formed in nuclear waste storage tanks. As many as six anions, aluminate, chromate, nitrate, nitrite, phosphate, and sulfate, are simultaneously determined in about one hour. Carbonate may also be determined, but in the presence of the prevalent nitrate, a chemical separation is required. Individual methods have been relegated to a secondary status due to the many advantages of LRS. Advantages such as small sample size, speed of analysis, accuracy, and specificity will be discussed. The typical precision obtained for analyses in high concentration is around five percent relative standard deviation.

  12. DETERMINATIONS OF THE ENVIRONMENTAL TOXICITY CHARACTERISTICS OF HAZARDOUS INDUSTRIAL WASTE FROM LANDFILL LEACHATE (CASE STUDY

    Directory of Open Access Journals (Sweden)

    Daniela Dal Molin

    2010-04-01

    Full Text Available The aim of this study was to evaluate the environmental toxicity of hazardous industrial waste from landfill leachate of the one industrial solid waste center from the Rio Grande do Sul state, Brazil. The physical and chemical characteristics, as well as the ecotoxicity with Daphnia magna and toxicity and mutagenicity with Allium cepa were determined. The results of the row leachate sample indicated that the physical and chemical characteristics are compatible with the limit values imputed for treated wastewaters. Absence of acute ecotoxicity was also detected, however a significant (P<0.01 larger frequency of micronuclei was verified when compared with the results of the negative control, suggesting a genotóxico effect of this wast, although not significant alterations in the mitotic index and root growth was observed.

  13. [Simultaneous determination of 11 bisphenols in plastic bottled drinking water by ultra performance liquid chromatography-tandem mass spectrometry].

    Science.gov (United States)

    Gou, Xinlei; Gao, Xia; Hu, Guanghui; Chi, Haitao; Le, Shengfeng; Wang, Wei; Liu, Weili

    2014-09-01

    A sensitive method was developed for the simultaneous determination of 11 bisphenols in plastic bottled drinking water by ultra performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS). The samples were freeze-dried under vacuum and then dissolved with methanol. The separation was performed on a UPLC BEH C18 column (100 mm x 2.1 mm, 1.7 μm) by using 0.1% (v/v) NH3 · H2O and methanol as mobile phases with gradient elution at a flow rate of 0.2 mL/min. The electrospray ionization (ESI) source in negative ion mode was used for the analysis of the 11 bisphenols in the multiple reaction monitoring (MRM) mode. The results verified that the standard curves for the 11 bisphenols were obtained with good correlation coefficients (R2) > 0.997 in their concentration ranges. The limits of detection (LOD, S/N = 3) for the 11 bisphenols were in the range of 0.01-1.00 μg/L. The mean recoveries for the 11 bisphenols at three spiked levels (low, middle, high) were 75.3%-102.1% with the relative standard deviations of 1.5%-8.9%. Seven plastic bottled drinking water samples were tested, and no bisphenol was found. The method is accurate, simple, rapid and feasible for the simultaneous determination of bisphenols in plastic bottled drinking water.

  14. Complex methodology for determining the thermal properties of solid wastes from fossil fuels

    Energy Technology Data Exchange (ETDEWEB)

    Belyaev, A.A.; Glushnev, S.V.; Ignatova, N.N.

    1983-01-01

    Comparative method based on theory is presented for determining the thermal capacity and heat conductivity of wastes from coal mining and processing. A schematic diagram of an apparatus for measuring thermal properties of solids is presented. The method described determines effective heat capacity and coefficient of heat conductivity. The accuracy of the method and its limitations in laboratory and industrial practice are discussed. (6 refs.)

  15. Transfer characteristics of heavy metals under biomass waste and plastics waste co-firing conditions%生物质与塑料类垃圾混烧过程的重金属迁移特性

    Institute of Scientific and Technical Information of China (English)

    谢明超; 马晓茜; 曾广博

    2015-01-01

    To study the weight loss rate and transfer behavior of heavy metals (Pb,Cu,Zn)under biomass wastes and plastic wastes co-firing conditions,experiments about seven components (wood,paper,rubber,recycled PE,re-cycled PP,recycled PS and recycled PVC)were conducted on a tube furnace and a atomic absorption spectropho-tometer.The results show that,co-combustion of biomass and plastic wastes causes a decrease in weight loss rate of the samples,especially the paper.When the sample is burned alone,the volatilization rate of Pb can reach over 85%at 900 ℃,that of Cu in four plastic wastes can reach over 85% at 1 000 ℃,and that of Zn rises significantly at high temperatures.Pb can be captured in bottom ash when the paper is co-fired with the plastics except the PVC.Cu can be captured in bottom ash when the wood and paper are co-fired with the PVC and the rubber.Zn can be captured in bottom ash when the wood is co-fired with the plastics except the rubber or the paper with the PS.%为了研究生物质与塑料类垃圾混烧对失重率和重金属 Pb,Cu,Zn 迁移特性的影响,利用管式炉和原子吸收分光光度计对木、纸、橡胶、再生 PE、再生 PP、再生 PS 和再生 PVC 7种组分进行燃烧试验。结果表明:1)生物质与塑料类垃圾混烧会不同程度地降低样品失重率,纸比木降幅更明显;2)单样燃烧时,900℃下 Pb 的挥发率可达85%以上,1000℃下4种塑料中 Cu的挥发率可达85%以上,高温阶段 Zn 的挥发率明显上升;3)纸与除 PVC 外的塑料混烧可以使 Pb 固定在底灰中;4)木、纸分别与 PVC 和橡胶混烧,可以使 Cu 固定在底灰中;5)木与除橡胶外的塑料混烧、纸与 PS 混烧,均可使 Zn 固定在底灰中。

  16. Effect of Specimen Size on the Tensile Strength Behavior of the Plastic Waste Fiber Reinforced Soil – Lime – Rice Husk Ash Mixtures

    Directory of Open Access Journals (Sweden)

    Muntohar A.S.

    2011-01-01

    Full Text Available Improvement of tensile strength in fiber reinforced soil is an important research topic. A study has been undertaken to investigate the strength of stabilized clay-soil reinforced with randomly distributed discrete plastic waste fibers by carrying out split tensile strength test. In this study, the clay soil was stabilized with lime and rice husk ash mixtures. The main purpose of this research is to investigate the effect of specimen size to the tensile strength behavior. Testing procedure was formulated using extended ASTM C496 standard. The laboratory investigation results showed that split-tensile strength of reinforced specimens increased with increase in size. The limitations of the dataset indicate that specimen size of 70 mm in diameter is the threshold to produce reasonable representative strengths.

  17. Determination of spatial resolution of plastic scintillation fiber array with a simple method

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The spatial resolution of a position sensitive gamma-ray detector configuration based on plastic scintillation fiber array was measured using a Monte Carlo simulation method. Both point spread function and modulation transfer function (MTF) were presented. The factors that influence the spatial resolution were also discussed. The results of the simulation showed that the intrinsic spatial resolution was consistent with the size of the physical pixels and a few centimeters spatial resolution could be obtained under certain circumstances.

  18. Plasticity in habitat use determines metabolic response of fish to global warming in stratified lakes.

    Science.gov (United States)

    Busch, Susan; Kirillin, Georgiy; Mehner, Thomas

    2012-09-01

    We used a coupled lake physics and bioenergetics-based foraging model to evaluate how the plasticity in habitat use modifies the seasonal metabolic response of two sympatric cold-water fishes (vendace and Fontane cisco, Coregonus spp.) under a global warming scenario for the year 2100. In different simulations, the vertically migrating species performed either a plastic strategy (behavioral thermoregulation) by shifting their population depth at night to maintain the temperatures occupied at current in-situ observations, or a fixed strategy (no thermoregulation) by keeping their occupied depths at night but facing modified temperatures. The lake physics model predicted higher temperatures above 20 m and lower temperatures below 20 m in response to warming. Using temperature-zooplankton relationships, the density of zooplankton prey was predicted to increase at the surface, but to decrease in hypolimnetic waters. Simulating the fixed strategy, growth was enhanced only for the deeper-living cisco due to the shift in thermal regime at about 20 m. In contrast, simulating the plastic strategy, individual growth of cisco and young vendace was predicted to increase compared to growth currently observed in the lake. Only growth rates of older vendace are reduced under future global warming scenarios irrespective of the behavioral strategy. However, performing behavioral thermoregulation would drive both species into the same depth layers, and hence will erode vertical microhabitat segregation and intensify inter-specific competition between the coexisting coregonids.

  19. Use of recycled plastics in wood plastic composites - a review.

    Science.gov (United States)

    Kazemi Najafi, Saeed

    2013-09-01

    The use of recycled and waste thermoplastics has been recently considered for producing wood plastic composites (WPCs). They have great potential for WPCs manufacturing according to results of some limited researches. This paper presents a detailed review about some essential properties of waste and recycled plastics, important for WPCs production, and of research published on the effect of recycled plastics on the physical and mechanical properties of WPCs.

  20. OPTIMATION OF TIME AND CATALYST/FEED RATIO IN CATALYTIC CRACKING OF WASTE PLASTICS FRACTION TO GASOLINE FRACTION USING Cr/NATURAL ZEOLITE CATALYST

    Directory of Open Access Journals (Sweden)

    Wega Trisunaryanti

    2010-06-01

    Full Text Available Optimation of time and catalyst/feed ratio in catalytic cracking of waste plastics fraction to gasoline fraction using Cr/Natural Zeolite catalyst has been studied.The natural zeolite was calcined by using nitrogen gas at 500 oC for 5 hours. The chromium supported on to the zeolite was prepared by ion exchange methode with Cr(NO33.9H2O solution with chromium/zeolite concentration of 1% (w/w. The zeolite samples were then calcined  with nitrogen gas at 500 oC for 2 hours, oxidyzed with oxygen gas and reduced with hydrogen at 400 oC for 2 hours. The characterization of the zeolite catalyst by means of Si/Al ratio by UV-Vis spectroscopy, acidity with pyridine vapour adsorption and Na, Ca and Cr contents by atomic adsorption spectroscopy (AAS. The catalyst activity test was carried out in the cracking process of waste plastics fraction with boiling point range of 150 - 250 °C (consisted of C12 - C16 hydrocarbons at 450 oC for 30 min, 60 min and 90 min, and catalyst/feed ratio 1/1, 1/2, 1/3, ¼ (w/w. The result of catalyst activity test  showed  that  the maximum number  conversion of gasoline fraction (C5-C11 is 53,27% with relatively low coke formation using 1/3 catalyst/feed ratio and the cracking time of 60 min.. This  catalyst has  Si/Al ratio = 1,21 (w/w , acidity = 0,16 mmol/g and Na content = 0,81%, Ca content = 0,15% and Cr content 0,24%.   Keywords: zeolite, catalytic cracking, gasoline, chromium.

  1. 纸厂废弃塑料焚烧过程中HCl的排放特性%Emission characters of HCl during paper mill plastic waste incineration

    Institute of Scientific and Technical Information of China (English)

    桑圣欢; 段钰锋; 陈惠超; 冒咏秋; 张平平

    2013-01-01

    Plastic waste from a paper mill with chlorine incineration was investigated in a small tube furnace. Factors such as temperature, particle size, and detention time in the process of waste plastic incineration were considered. Thermogravimetric analysis (TG) coupled with Fourier transfer infrared spectroscopy was used to analyze emission characters of HCl. Results show that conversion rate of Cl to HCl increased with the temperature, particle size and detention time; TG-FTIR shows HC1 was generated at about 200 t, reached maximum at about 300 ℃. and declined gradually after 400 ℃. XRD indicates that residual chlorine resided in the ash in the form of inorganic chloride.%在小型管式炉中进行了纸厂含氯废弃塑料焚烧过程中HCl析出特性实验,研究了温度、粒径、停留时间对HCl析出的影响;同时借助热重-傅里叶红外光谱联用技术(TG-FTIR)研究了HCl在焚烧过程中的析出规律.结果发现,燃烧过程中Cl→HCl的转化率随温度、粒径和停留时间的增大而显著增加;TG-FTIR结果表明,HCl在200℃左右开始析出,300℃左右达到最大值,400℃后析出峰逐渐消失.XRD结果可知,残余氯以无机氯盐的形式存在灰样中.

  2. Degradation of Oxo-Biodegradable Plastic by Pleurotus ostreatus

    OpenAIRE

    José Maria Rodrigues da Luz; Sirlaine Albino Paes; Mateus Dias Nunes; Marliane de Cássia Soares da Silva; Maria Catarina Megumi Kasuya

    2013-01-01

    Growing concerns regarding the impact of the accumulation of plastic waste over several decades on the environmental have led to the development of biodegradable plastic. These plastics can be degraded by microorganisms and absorbed by the environment and are therefore gaining public support as a possible alternative to petroleum-derived plastics. Among the developed biodegradable plastics, oxo-biodegradable polymers have been used to produce plastic bags. Exposure of this waste plastic to ul...

  3. Degradation of Oxo-Biodegradable Plastic by Pleurotus ostreatus

    OpenAIRE

    José Maria Rodrigues da Luz; Sirlaine Albino Paes; Mateus Dias Nunes; Marliane de Cássia Soares da Silva; Maria Catarina Megumi Kasuya

    2013-01-01

    Growing concerns regarding the impact of the accumulation of plastic waste over several decades on the environmental have led to the development of biodegradable plastic. These plastics can be degraded by microorganisms and absorbed by the environment and are therefore gaining public support as a possible alternative to petroleum-derived plastics. Among the developed biodegradable plastics, oxo-biodegradable polymers have been used to produce plastic bags. Exposure of this waste plastic to ul...

  4. A preliminary study on the preparation of wood-plastic composites from urban wastes generated in Merida, Mexico with potential applications as building materials.

    Science.gov (United States)

    Cruz-Estrada, Ricardo H; Martínez-Tapia, Gustavo E; Canché-Escamilla, Gonzalo; González-Chí, Pedro I; Martín-Barrera, Cesar; Duarte-Aranda, Santiago; Guillén-Mallette, Javier; Cupul-Manzano, Carlos V; Martínez-Domínguez, Osvaldo; García-Gómez, Carmen

    2010-09-01

    A preliminary study on the use of wood and plastic wastes generated in Merida, Mexico to assess their potential for the development of building materials is reported. Composites based on recycled, high-density polyethylene (R-HDPE) loaded with wood particles were prepared. The R-HDPE was collected from Merida's Separation Plant, where it was sorted from other residues, either organic or inorganic. Composites based on virgin, high-density polyethylene (V-HDPE) were also prepared to assess the effect of the R-HDPE on the composite's mechanical properties. The wood came from the trims of different varieties of the city's trees that are periodically pruned as part of the cleaning and urbanising programmes implemented by the City Council. A batch of this material was selected at random to incorporate into both the R-HDPE and V-HDPE. Different wood particle sizes were experimented with to obtain extruded composites with contents of 50% and 60% by weight of wood that were characterized under tension and impact. Flat wood-plastic extrudates with reasonable good appearance were also produced at the laboratory level as a first step to find an adequate route to scale-up the process to a pilot level to evaluate the feasibility of producing alternative building materials.

  5. Exhaust Gas Pollution and Control of Import Waste Plastics Recycling Industry%进口废塑料再生加工行业废气污染及防治对策

    Institute of Scientific and Technical Information of China (English)

    陈瑜; 赵艳

    2015-01-01

    With large quantities of China’s import waste plastics, exhaust gas could be produced in the recycling process of waste plastics. Without effective treatment, the production will bring great harm to the environment. Typical regeneration of waste plastics process and the production process were analyzed. The main sources and types of waste gas were identified. Effective treatments and countermeasures of organic waste gas, dust and odor pollution produced in the process of hot-melt granulation, crushing were presented.%我国进口废塑料数量大,废塑料再生加工生产过程中伴随着工艺废气的产生,若不进行处理将对环境带来较大的危害。通过分析典型的废塑料再生加工工艺及产污环节,识别主要工艺废气来源及种类,提出了有效处理热熔造粒、破碎等加工过程产生的有机废气、粉尘及恶臭等废气污染物的防治对策与措施。

  6. Effective solutions for monitoring the electrostatic separation of metal and plastic granular waste from electric and electronic equipment.

    Science.gov (United States)

    Senouci, Khouira; Medles, Karim; Dascalescu, Lucian

    2013-02-01

    The variability of the quantity and purity of the recovered materials is a serious drawback for the application of electrostatic separation technologies to the recycling of granular wastes. In a series of previous articles we have pointed out how capability and classic control chart concepts could be employed for better mastering the outcome of such processes. In the present work, the multiple exponentially weighted moving average (MEWMA) control chart is introduced and shown to be more effective than the Hotelling T2 chart for monitoring slow varying changes in the electrostatic separation of granular mixtures originating from electric and electronic equipment waste. The operation of the industrial process was simulated by using a laboratory roll-type electrostatic separator and granular samples resulting from shredded electric cable wastes. The 25 tests carried out during the observation phase enabled the calculation of the upper and lower control limits for the two control charts considered in the present study. The 11 additional tests that simulated the monitoring phase pointed out that the MEWMA chart is more effective than Hotelling's T(2) chart in detecting slow varying changes in the outcome of a process. As the reverse is true in the case of abrupt alterations of monitored process performances, simultaneous usage of the two control charts is strongly recommended. While this study focused on a specific electrostatic separation process, using the MEWMA chart together with the well known Hotelling's T(2) chart should be applicable to the statistical control of other complex processes in the field of waste processing.

  7. ENVIRONMENTAL RESEARCH BRIEF: WASTE REDUCTION ACTIVITIES AND OPTIONS FOR A MANUFACTURER OF FIRE RETARDANT PLASTIC PELLETS AND HOT MELT ADHESIVES.

    Science.gov (United States)

    The U.S. Environmental Protection Agency (EPA) funded a project with the New Jersey Department of Environmental Protection and Energy (NJDEPE) to assist in conducting waste minimization assessments at thirty small to medium sized businesses in the state of New Jersey. One of the...

  8. ENVIRONMENTAL RESEARCH BRIEF: WASTE REDUCTION ACTIVITIES AND OPTIONS FOR A MANUFACTURER OF PLASTIC CONTAINERS BY INJECTION MOLDING.

    Science.gov (United States)

    The U.S. Environmental Protection Agency (EPA) funded a project with the New Jersey Department of Environmental Protection and Energy (NJDEPE) to assist in conducting waste minimization assessments at thirty small- to medium-sized businesses in the state of New Jersey. ne of the ...

  9. Critical comparison of radiometric and mass spectrometric methods for the determination of radionuclides in environmental, biological and nuclear waste samples

    DEFF Research Database (Denmark)

    Hou, Xiaolin; Roos, Per

    2008-01-01

    spectrometry, and glow discharge mass spectrometry are reviewed for the determination of radionuclides. These methods are critically compared for the determination of long-lived radionuclides important for radiation protection, decommissioning of nuclear facilities, repository of nuclear waste, tracer...

  10. Gross alpha determination in radioactive wastes from nuclear power plants using the track registration technique

    Energy Technology Data Exchange (ETDEWEB)

    Suarez-Navarro, M.J. [Universidad Politecnica de Madrid (UPM) E.T.S.I de Caminos, Canales y Puertos, Profesor Aranguren, s/n, 28040 Madrid (Spain)]. E-mail: he04@caminos.upm.es; Pujol, Ll. [Centro de Estudios y Experimentacion de Obras Publicas (CEDEX), Alfonso XII, 3, 28014 Madrid (Spain); Gonzalez-Gonzalez, J.A. [Universidad Politecnica de Madrid (UPM) E.T.S.I de Caminos, Canales y Puertos, Profesor Aranguren, s/n, 28040 Madrid (Spain)

    2007-03-15

    Low and intermediate level nuclear wastes (ion-exchange resins and evaporator concentrates) essentially contain beta and gamma emitters, with very few alpha emitters. Several techniques may be used to determine gross alpha activity but, in this case, solid-state nuclear track detectors (SSNTDs) are a suitable technique for gross alpha determination because track detectors are not sensitive to beta and gamma emitters. Also, this technique is simple and inexpensive. In this paper, we studied the parameters (background, efficiency and self-absorption) that could affect the gross alpha determination using SSNTDs for both sample preparation methods, the 'dry method' with tensioactives and the 'wet method'. For the 'dry method', a self-absorption curve for {sup 241}Am standard was prepared using a set of varying thickness of sodium salt and for two different tensioactives: Tween{sup (R)}20 and Teg. The results showed that, below 1mg/cm{sup 2}, the self-absorption factor can be considered similar for both tensioactives and equal to unity. Several detectors for gross alpha determination were compared and we found that the most suitable techniques were ZnS(Ag) solid scintillator and track detectors. Both detectors were used to compare radioactive waste samples. Finally, the proposed methods ('dry method' with Teg tensioactive and 'wet method') using track detectors were tested by analysing the gross alpha activity of several radioactive wastes.

  11. Monte-Carlo simulation for determining SNR and DQE of linear array plastic scintillating fiber

    Institute of Scientific and Technical Information of China (English)

    Mohammad Mehdi NASSERI; MA Qing-Li; YIN Ze-Jie; WU Xiao-Yi

    2004-01-01

    Fundamental characteristics of the plastic-scintillating fiber (PSF) for wide energy range of electromagnetic radiation (X & γ) have been studied to evaluate possibility of using the PSF as an imaging detector for industrial purposes. Monte-Carlo simulation program (GEANT4.5.1, 2003) was used to generate the data. In order to evaluate image quality of the detector, fiber array was irradiated under various energy and fluxes. Signal to noise ratio (SNR)as well as detector quantum efficiency (DQE) were obtained.

  12. Determining an Efficient Solvent Extraction Parameters for Re-Refining of Waste Lubricating Oils

    Directory of Open Access Journals (Sweden)

    Hassan Ali Durrani

    2012-04-01

    Full Text Available Re-refining of vehicle waste lubricating oil by solvent extraction is one of the efficient and cheapest methods. Three extracting solvents MEK (Methyl-Ethyl-Ketone, 1-butanol, 2-propanol were determined experimentally for their performance based on the parameters i.e. solvent type, solvent oil ratio and extraction temperature. From the experimental results it was observed the MEK performance was highest based on the lowest oil percent losses and highest sludge removal. Further, when temperature of extraction increased the oil losses percent also decreased. This is due to the solvent ability that dissolves the base oil in waste lubricating oil and determines the best SOR (Solvent Oil Ratio and extraction temperatures.

  13. Electrochemical Sensor for the Selective Determination of Prindopril Based on Phosphotungestic Acid Plastic Membrane

    Energy Technology Data Exchange (ETDEWEB)

    Zareh, Mohsen M. [Univ. of Tabuk, Tabuk (Saudi Arabia); Wasel, Anower M. [Association of Drug Agency, Cairo (Egypt); Abd Alkreem, Yasser M. [Zagazig Univ., Zagazig (Egypt)

    2013-10-15

    A novel PVC membrane sensor for perindopril based on perindopril-phosphotungstate ion pair complex was prepared. The influence of membrane composition (i.e. percent of PVC, plasticizer, ion-pair complex, and kind of plasticizer), inner solution, pH of test solution and foreign cations on the electrode performance was investigated. The optimized membrane demonstrates Nernstian response (30.9 ± 1.0 mV per decade) for perindopril cations over a wide linear range from 9.0 Χ 10{sup -7} to 1 Χ 10{sup -2} M at 25 .deg. C. The potentiometric response is independent of the pH in the range of 4.0-9.5. The proposed sensor has the advantages of easy preparation, fast response time. The selectivity coefficients indicate excellent selectivity for perindopril over many common cations (e. g., Na{sup +}, K{sup +}, Mg{sup 2+}, Cu{sup 2+}, Ni{sup 2+}, rhamnose, maltose, glycine and benzamide). The practical applications of this electrode was demonstrated by measuring the concentrations of perindopril in pure solutions and pharmaceutical preparations with satisfactory results.

  14. Tests for determining impact resistance and strength of glass used for nuclear waste disposal

    Energy Technology Data Exchange (ETDEWEB)

    Bunnell, L.R.

    1979-05-01

    Tests are described for determining the impact resistance (Section A) and static tensile strength (Section B) of glasses containing simulated or actual nuclear wastes. This report describes the development and use of these tests to rank different glasses, to assess effects of devitrification, and to examine the effect of impact energy on resulting surface area. For clarity this report is divided into two sections, Impact Resistance and Tensile Strength.

  15. DETERMINATION OF PERRHENATE ADSORPTION KINETICS FROM HANFORD WASTE SIMULANTS USING SUPERLING 639 RESIN

    Energy Technology Data Exchange (ETDEWEB)

    Duffey, C.; King, W.; Hamm, L.

    2002-04-02

    This report describes the results of SuperLig{reg_sign} 639 sorption kinetics tests conducted at the Savannah River Technology Center (SRTC) in support of the Hanford River Protection Project - Waste Treatment Plant (RPP-WTP). The RPP-WTP contract was awarded to Bechtel for the design, construction, and initial operation of a plant for the treatment and vitrification of millions of gallons of radioactive waste currently stored in tanks at Hanford, WA. Part of the current treatment process involves the removal of technetium from tank supernate solutions using columns containing SuperLig{reg_sign} 639 resin. This report is part of a body of work intended to quantify and optimize the operation of the technetium removal columns with regard to various parameters (such as liquid flow rate, column aspect ratio, resin particle size, loading and elution temperature, etc.). The tests were conducted using nonradioactive simulants of the actual tank waste samples containing rhenium as a chemical surrogate for the technetium in the actual waste. Previous column tests evaluated the impacts of liquid flow rate, bed aspect ratio, solution temperature and composition upon SuperLig{reg_sign} 639 column performance (King et al., 2000, King et al., 2003). This report describes the results of kinetics tests to determine the impacts of resin particle size, solution composition, and temperature on the rate of uptake of perrhenate ions.

  16. Attenuated total reflectance-mid infrared spectroscopy (ATR-MIR) coupled with independent components analysis (ICA): A fast method to determine plasticizers in polylactide (PLA).

    Science.gov (United States)

    Kassouf, Amine; Ruellan, Alexandre; Jouan-Rimbaud Bouveresse, Delphine; Rutledge, Douglas N; Domenek, Sandra; Maalouly, Jacqueline; Chebib, Hanna; Ducruet, Violette

    2016-01-15

    Compliance of plastic food contact materials (FCMs) with regulatory specifications in force, requires a better knowledge of their interaction phenomena with food or food simulants in contact. However these migration tests could be very complex, expensive and time-consuming. Therefore, alternative procedures were introduced based on the determination of potential migrants in the initial material, allowing the use of mathematical modeling, worst case scenarios and other alternative approaches, for simple and fast compliance testing. In this work, polylactide (PLA), plasticized with four different plasticizers, was considered as a model plastic formulation. An innovative analytical approach was developed, based on the extraction of qualitative and quantitative information from attenuated total reflectance (ATR) mid-infrared (MIR) spectral fingerprints, using independent components analysis (ICA). Two novel chemometric methods, Random_ICA and ICA_corr_y, were used to determine the optimal number of independent components (ICs). Both qualitative and quantitative information, related to the identity and the quantity of plasticizers in PLA, were retrieved through a direct and fast analytical method, without any prior sample preparations. Through a single qualitative model with 11 ICs, a clear and clean classification of PLA samples was obtained, according to the identity of plasticizers incorporated in their formulations. Moreover, a quantitative model was established for each formulation, correlating proportions estimated by ICA and known concentrations of plasticizers in PLA. High coefficients of determination (higher than 0.96) and recoveries (higher than 95%) proved the good predictability of the proposed models.

  17. Some exploitation properties of wood plastic composites (WPC, based on high density polyethylene and timber industry waste

    Directory of Open Access Journals (Sweden)

    janis kajaks

    2015-09-01

    Full Text Available Abstract: In this study, the influence of wood fiber content (40, 50 and 60 wt.% and coupling agent concentration (3 and 5 wt.% on the mechanical properties of wood-plastic composites (WPCs was investigated. Two types of plastic (high-density-polyethylene (HDPE and recycled high-density-polyethylene (rHDPE were used as polymer matrices for preparing WPC. As reinforcement, prior grinded (fiber length < 0.5 mm coniferous wood shavings were utilized. Overall trend showed, that by adding a wood fiber, flexural properties and microhardness of the composites significantly were enhanced. However, impact strength, water resistance, and fluidity of polymer melts decreased with increase in fiber content. The virgin HDPE-based composites as well as recycled HDPE-based composites, reinforced with fibers from coniferous wood, showed good mechanical properties. Based on the findings in this work, it appears that WPCs based on virgin HDPE, as well as on recycled HDPE, can be used to manufacture value-added panels. Optimal content of wood fibres were 50-60 wt.%.DOI: http://dx.doi.org/10.5755/j01.ms.21.3.7283

  18. Deactivation of REY zeolite during catalytic cracking of heavy oil obtained from the pyrolysis of waste plastics; REY zeolite shokubai ni yoru hai plastic netsu bunkaiyu no sesshoku bunkai hanno no kassei rekka

    Energy Technology Data Exchange (ETDEWEB)

    Masuda, T.; Mukai, S.; Akiyama, T.; Fujikata, Y.; Hashimoto, K. [Kyoto University, Kyoto (Japan)

    1995-12-10

    A model has been developed to represent the deactivation of REY zeolite caused by coke deposition during catalytic cracking of heavy oil obtained from pyrolysis of waste plastics. Coke deposition not only leads to coverage of the acid sites, which contribute to the reaction, but also leads to a decrease in the intracrystalline diffusivity of the zeolite due to the reduction in effective pore opening, resulting in deactivation of the catalyst. In this work, firstly the amount of strong acid sites and the diffusivity of catalysts with different amounts of coke loading were measured, and empirical equations, which represent the relationships between the amount of coke loading and these two values, were obtained. Finally, a model was developed to calculate the transient change of the catalyst activity and the concentration distributions of the components within the reactor by employing the obtained empirical equations. The calculated results agreed well with experimental results. Using this model, it was found that the deactivation rate of the catalyst was reduced under diffusion control conditions, and large catalyst particles could maintain their activity longer than small catalyst particles. 12 refs., 9 figs., 1 tab.

  19. Task Technical and Quality Assurance Plan for Determining Uranium and Plutonium Solubility in Actual Tank Waste Supernates

    Energy Technology Data Exchange (ETDEWEB)

    King, William D.

    2005-06-28

    Savannah River Site tank waste supernates contain small quantities of dissolved uranium and plutonium. Due to the large volume of supernates, significant quantities of dissolved uranium and plutonium are managed as part of waste transfers, evaporation and pretreatment at the Savannah River Site in tank farm operations, the Actinide Removal Project (ARP), and the Salt Waste Processing Facility (SWPF). Previous SRNL studies have investigated the effect of temperature and major supernate components on the solubility of uranium and plutonium. Based on these studies, equations were developed for the prediction of U and Pu solubility in tank waste supernates. The majority of the previous tests were conducted with simulated waste solutions. The current testing is intended to determine solubility in actual tank waste samples (as-received, diluted, and combinations of tank samples) as a function of composition and temperature. Results will be used to validate and build on the existing solubility equations.

  20. 废旧塑料在复合材料领域中回用技术的研究进展%Research Advances in the Recycling Technologies of Waste Plastics in Composites Field

    Institute of Scientific and Technical Information of China (English)

    张效林; 王汝敏; 王志彤; 冯冰; 付钰

    2011-01-01

    介绍了国内外废旧塑料现状以及废旧塑料在复合材料领域利用新进展,综述了废旧塑料在植物纤维/废旧塑料复合材料、废纸/废塑料复合材料、木塑复合发泡材料、可生物降解塑料复合材料及其他复合材料领域的再利用技术新进展,并分析了废旧塑料在复合材料领域回收再利用技术的发展趋势,提出应进一步探讨不同种类废旧塑料对复合材料力学性能及植物纤维/废旧塑料界面相容性的影响.%The present research status and category of printing and packaging waste plastic are introduced,and research advances in the recycling technology of different kind of waste plastic in composite material field such as plant fibre/recycled thermoplastic composites, wastepaper/thermoplastic polymer composites, wood-plastic foaming composites, eco-friendly biodegradable composites and other composites are discussed. Development trend of the recycling technology of waste plastic in composite material field is pointed out. And further more, research area such as the effect of different waste plastics on the composites interface compatibility is proposed.

  1. DETERMINATION OF HEAT TRANSFER COEFFICIENTS FOR FRENCH PLASTIC SEMEN STRAW SUSPENDED IN STATIC NITROGEN VAPOR OVER LIQUID NITROGEN.

    Science.gov (United States)

    Santo, M V; Sansinena, M; Chirife, J; Zaritzky, N

    2015-01-01

    The use of mathematical models describing heat transfer during the freezing process is useful for the improvement of cryopreservation protocols. A widespread practice for cryopreservation of spermatozoa of domestic animal species consists of suspending plastic straws in nitrogen vapor before plunging into liquid nitrogen. Knowledge of surface heat transfer coefficient (h) is mandatory for computational modelling; however, h values for nitrogen vapor are not available. In the present study, surface heat transfer coefficients for plastic French straws immersed in nitrogen vapor over liquid nitrogen was determined; vertical and horizontal positions were considered. Heat transfer coefficients were determined from the measurement of time-temperature curves and from numerical solution of heat transfer partial differential equation under transient conditions using finite elements. The h values experimentally obtained for horizontal and vertically placed straws were compared to those calculated using correlations based on the Nusselt number for natural convection. For horizontal straws the average obtained value was h=12.5 ± 1.2 W m(2) K and in the case of vertical straws h=16 ± 2.48 W m(2) K. The numerical simulation validated against experimental measurements, combined with accurate h values provides a reliable tool for the prediction of freezing curves of semen-filled straws immersed in nitrogen vapor. The present study contributes to the understanding of the cryopreservation techniques for sperm freezing based on engineering concepts, improving the cooling protocols and the manipulation of the straws.

  2. Flow Curve Determination at Large Plastic Strain Levels to Accurately Constitutive Equations of AHSS in Forming Simulation

    Science.gov (United States)

    Lemoine, X.; Sriram, S.; Kergen, R.

    2011-05-01

    ArcelorMittal continuously develops new steel grades (AHSS) with high performance for the automotive industry to improve the weight reduction and the passive safety. The wide market introduction of AHSS raises a new challenge for manufacturers in terms of material models in the prediction of forming—especially formability and springback. The relatively low uniform elongation, the high UTS and the low forming limit curve of these AHSS may cause difficulties in forming simulations. One of these difficulties is the consequence of the relatively low uniform elongation on the parameters identification of isotropic hardening model. Different experimental tests allow to reach large plastic strain levels (hydraulic bulge test, stack compression test, shear test…). After a description on how to determine the flow curve in these experimental tests, a comparison of the different flow curves is made for different steel grades. The ArcelorMittal identification protocol for hardening models is only based on stress-strain curves determined in uniaxial tension. Experimental tests where large plastic strain levels are reached are used to validate our identification protocol and to recommend some hardening models. Finally, the influence of isotropic hardening models and yield loci in forming prediction for AHSS steels will be presented.

  3. Electrochemical methods for the determination of the diffusion coefficient of ionophores and ionophore-ion complexes in plasticized PVC membranes.

    Science.gov (United States)

    Bodor, Sándor; Zook, Justin M; Lindner, Erno; Tóth, Klára; Gyurcsányi, Róbert E

    2008-05-01

    The diffusion coefficients of active components in ion-selective membranes have a decisive influence on the life-time and detection limit of the respective ion-selective electrodes, as well as influencing the rate of polarization and relaxation processes of electrically perturbed ion sensors. Therefore, the rational design of mass transport controlled ion-selective electrodes with sub-nanomolar detection limits requires reliable data on the diffusion coefficients. We have implemented electrochemical methods for the quantitative assessment of both the diffusion coefficients of free ionophores and ion-ionophore complexes. The diffusion coefficients of the pH-sensitive chromoionophore ETH 5294 and the calcium-selective ionophore ETH 5234 were determined in plasticized PVC membranes with different PVC to plasticizer ratios. The diffusion coefficient of the free chromoionophore determined by a chronoamperometric method was validated with optical methods for a variety of membrane compositions. The calcium-selective ionophore ETH 5234 was used as a model compound to assess the diffusion coefficient of the ion-ionophore complex calculated from the time required for the complexes to cross a freshly prepared membrane during potentiometric ion-breakthrough experiments. The difference between the diffusion coefficients of the free ionophore ETH 5234 and the ion-ionophore complex was found to be significant and correlated well with the geometry of the respective species.

  4. Residential Waste

    DEFF Research Database (Denmark)

    Christensen, Thomas Højlund; Fruergaard, Thilde; Matsufuji, Y.

    2011-01-01

    are discussed in this chapter. Characterizing residential waste is faced with the problem that many residences already divert some waste away from the official collection systems, for example performing home composting of vegetable waste and garden waste, having their bundled newspaper picked up by the scouts...... twice a year or bringing their used furniture to the flea markets organized by charity clubs. Thus, much of the data available on residential waste represents collected waste and not necessarily all generated waste. The latter can only be characterized by careful studies directly at the source......Residential waste comes from residential areas with multi-family and single-family housing and includes four types of waste: household waste, garden waste, bulky waste and household hazardous waste. Typical unit generation rates, material composition, chemical composition and determining factors...

  5. Residential Waste

    DEFF Research Database (Denmark)

    Christensen, Thomas Højlund; Fruergaard, Thilde; Matsufuji, Y.

    2011-01-01

    Residential waste comes from residential areas with multi-family and single-family housing and includes four types of waste: household waste, garden waste, bulky waste and household hazardous waste. Typical unit generation rates, material composition, chemical composition and determining factors...... are discussed in this chapter. Characterizing residential waste is faced with the problem that many residences already divert some waste away from the official collection systems, for example performing home composting of vegetable waste and garden waste, having their bundled newspaper picked up by the scouts...... twice a year or bringing their used furniture to the flea markets organized by charity clubs. Thus, much of the data available on residential waste represents collected waste and not necessarily all generated waste. The latter can only be characterized by careful studies directly at the source...

  6. Determination of long-lived Nb isotopes in nuclear power plant wastes

    Energy Technology Data Exchange (ETDEWEB)

    Osvath, Szabolcs [Institute of Nuclear Techniques, Budapest University of Technology and Economics, Muegyetem Rakpart 9, 1111 Budapest (Hungary)], E-mail: osvath@reak.bme.hu; Vajda, Nora; Molnar, Zsuzsa [Institute of Nuclear Techniques, Budapest University of Technology and Economics, Muegyetem Rakpart 9, 1111 Budapest (Hungary)

    2008-01-15

    {sup 94}Nb and {sup 93m}Nb are long-lived radionuclides, produced by thermal and fast neutrons from {sup 93}Nb that is a major component of the Zr alloys used in nuclear reactors. A radiochemical method for the determination of these nuclides has been developed. The separation is based on the insolubility of Nb oxides and the retention of the fluoric complexes on anion exchange resin. The Nb sources are detected by {gamma}- and X-ray spectrometries. Activity concentrations determined in radioactive waste samples of a nuclear power plant are presented.

  7. Determination of long-lived Nb isotopes in nuclear power plant wastes.

    Science.gov (United States)

    Osváth, Szabolcs; Vajda, Nóra; Molnár, Zsuzsa

    2008-01-01

    (94)Nb and (93m)Nb are long-lived radionuclides, produced by thermal and fast neutrons from (93)Nb that is a major component of the Zr alloys used in nuclear reactors. A radiochemical method for the determination of these nuclides has been developed. The separation is based on the insolubility of Nb oxides and the retention of the fluoric complexes on anion exchange resin. The Nb sources are detected by gamma- and X-ray spectrometries. Activity concentrations determined in radioactive waste samples of a nuclear power plant are presented.

  8. Application of laser-induced photoacoustic spectroscopy for determination of plutonium concentration in nuclear waste solutions.

    Science.gov (United States)

    Surugaya, Naoki; Sato, Soichi; Jitsukata, Syu; Watahiki, Masaru

    2008-04-01

    Laser-induced photoacoustic spectroscopy was used in a quantitative analysis of Pu in HNO3 medium. Plutonium was quantitatively oxidized to Pu(VI) using Ce(IV). The photoacoustic measurement of Pu(VI) with maximum absorption at 830.5 nm was subsequently performed to determine the concentration. The photoacoustic signal was linearly proportional to the Pu(VI) ion concentration. The detection limit of Pu(VI) was estimated to be 0.5 microg mL(-1) (3sigma) in 3 M HNO3. By the proposed method, Pu concentration was successfully determined in a nuclear waste solution for use in nuclear materials management.

  9. Determination of the radionuclide inventory in accelerator waste using calculation and radiochemical analysis

    Energy Technology Data Exchange (ETDEWEB)

    Schumann, D.; Neuhausen, J.; Weinreich, R. [Paul Scherrer Institut, CH-5232 Villigen PSI (Switzerland); Atchison, F. [Paul Scherrer Institut, CH-5232 Villigen PSI (Switzerland)], E-mail: francis.atchison@psi.ch; Kubik, P.; Synal, H.-A. [Paul Scherrer Institut, c/o Institute of Particle Physics, ETH Zuerich, CH-8093 Zurich (Switzerland); Korschinek, G.; Faestermann, Th.; Rugel, G. [Technische Universitaet Muenchen, D-85747 Garching (Germany)

    2007-11-15

    We use a description of the work carried out to determine the radioactive inventory for a redundant beam-dump from the PSI accelerator complex, as an illustration of techniques for the classification and characterisation of accelerator waste and how some difficulties can be circumvented. The work has been carried out using a combination of calculation and sample analysis: The inventory calculation effectively involves a large scale Monte-Carlo transport calculation of a medium-sized spallation facility and for the sample analysis, standard radiochemical analysis techniques have had to be extended to include AMS measurements so as to allow measurement of some of the long half-life, waste disposal relevant, nuclides.

  10. Determination of Different Metals in Steel Waste Samples Using laser Induced Breakdown Spectroscopy

    Directory of Open Access Journals (Sweden)

    A. H. Bakry

    2007-12-01

    Full Text Available Elemental analysis of waste samples collected from steel products manufacturing plant (SPS located at industrial city of Jeddah, Saudi-Arabia has been carried out using Laser Induced Breakdown Spectroscopy (LIBS. The 1064 nm laser radiations from a Nd:YAG laser at an irradiance of 7.6  1010 W cm –2 were used. Atomic emission spectra of the elements present in the waste samples were recorded in the 200 – 620 nm region. Elements such as Fe, W, Ti, Al, Mg, Ca, S, Mn, and Na were detected in these samples. Quantitative determination of the elemental concentration was obtained for these metals against certified standard samples. Parametric dependences of LIBS signal intensity on incident laser energy and time delay between the laser pulse and data acquisition system were also carried out.

  11. Staged pyrolysis, a process for chemical separation of waste plastics; Gestufte Pyrolyse als Verfahrensprinzip zur chemischen Auftrennung von Kunststoffgemischen

    Energy Technology Data Exchange (ETDEWEB)

    Hornung, A.; Hornung, U.; Schoeneberger, A.; Weichmann, J. [Kaiserslautern Univ. (Germany). Fachbereich Chemie; Bockhorn, H. [Karlsruhe Univ. (T.H.) (Germany). Inst. fuer Chemische Technik

    1996-12-31

    It is shown that staged pyrolysis of mixed plastics (polystyrene, polyethylene, polyvinyl chloride, polyamide 6) can be carried out in spherical recirculation reactors or in cascades of spherical recirculation reactors at exact temperature levels, and that the times of residue and reaction temperatures of laboratory systems can be calculated from the formal kinetic parameters obtained in nonisothermal and isothermal investigations. (orig) [Deutsch] Es konnte gezeigt werden, dass das Prinzip der stufenweisen Pyrolyse von Kunststoffgemischen (Polystyrol, Polyethylen, Polyvinylchlorid bzw. Polyamid 6) im Kugelkreislaufreaktor und der Kaskade aus Kugelkreislaufreaktoren unter Einhaltung der exakten Temperaturniveaus realisierbar ist und die Auslegung der Laboranlage hinsichtlich der Verweilzeiten und Temperaturniveaus mit Hilfe der formalkinetischen Parameter aus nicht-isothermen und isothermen Untersuchungen moeglich ist. (orig)

  12. Recycling of Plastic Packaging Wastes%塑料包装废弃物的再生利用

    Institute of Scientific and Technical Information of China (English)

    贺全国; 聂立波

    2011-01-01

    塑料包装在整个包装产业中占有极大比例,其废弃物的处理给国际社会减碳减排发展带来了巨大挑战。结合国内外对塑料包装废弃物的管理现状,分析了塑料包装废弃物的来源、分类和化学组成,阐述了国外塑料包装废弃物的回收分离技术和设备及国内相应研究现状;对塑料包装废弃物的再生利用途径进行深入解析,较全面地阐述了塑料包装废弃物再生利用的原理与研究现状;提出了塑料包装废弃物再生利用的基本策略建议。%The plastic packaging accounts for a very great proportion in the packaging industry,and the plastic packaging wastes(PPW) disposal brings great confrontation and challenge for global carbon emission reduction development.Based on the international practical PPW management,analyzes the source,classification and chemical composition for PPW and expounds the recycling separation technology and apparatus at aboard and the domestic research status;Resolves various PPW disposal approaches and elaborates comprehensively PPW regeneration principles and practices;Presents strategic suggestions on recycling and utilization of PPW.

  13. Plastic Bronchitis.

    Science.gov (United States)

    Rubin, Bruce K

    2016-09-01

    Plastic bronchitis is an uncommon and probably underrecognized disorder, diagnosed by the expectoration or bronchoscopic removal of firm, cohesive, branching casts. It should not be confused with purulent mucous plugging of the airway as seen in patients with cystic fibrosis or bronchiectasis. Few medications have been shown to be effective and some are now recognized as potentially harmful. Current research directions in plastic bronchitis research include understanding the genetics of lymphatic development and maldevelopment, determining how abnormal lymphatic malformations contribute to cast formation, and developing new treatments. Copyright © 2016 Elsevier Inc. All rights reserved.

  14. Thermal and physical property determination for IONSIV/256 IE-911 crystalline silicotitanate and Savannah River Site waste simulant solutions

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-12-08

    This document describes physical and thermophysical property determinations that were made in order to resolve questions associated with the decontamination of Savannah River Site waste streams using ion exchange on crystalline silicotitanate.

  15. Dealing with the ubiquity of phthalates in the laboratory when determining plasticizers by gas chromatography/mass spectrometry and PARAFAC.

    Science.gov (United States)

    Oca, M L; Rubio, L; Sarabia, L A; Ortiz, M C

    2016-09-16

    Determining plasticizers and other additives migrated from plastic materials becomes a hard task when these substances are already present in the laboratory environment. This work dealt with this drawback in the multiresidue determination of four plasticizers (2,6-di-tert-butyl-4-methyl-phenol (BHT), diisobutyl phthalate (DiBP), bis(2-ethylhexyl) adipate (DEHA) and diisononyl phthalate (DiNP)) and a UV stabilizer (benzophenone (BP)) by gas chromatography/mass spectrometry (GC/MS) using DiBP-d4 as internal standard. The ubiquity of DiBP by a non-constant leaching process in the laboratory was detected, which could not guarantee the achievement of a trustworthy quantification. To handle this, the assessment of the level of DiBP in solvent blanks having fixed the probabilities of false non-compliance (α) and false compliance (β) at 0.01 was performed. On the other hand, another special case was that of DiNP, in whose chromatogram finger peaks appear because of an array of possible C9 isomers. PARAFAC, used for the identification and quantification of all the substances, is a useful chemometric tool that enabled a more reliable determination of this analyte since no peak areas were considered but chromatographic and spectral loadings. Since phthalates may migrate from rubber latex items, an evaluation of the existence of matrix effects on the determination of the five analytes was conducted prior to an extraction with hexane from a dummy for infants. As matrix effects were present, the quantification of the compounds under study was performed following the standard addition method using PARAFAC sample loadings as response variable. As a result, the presence of BHT was confirmed, being its concentration equal to 37.87μgL(-1). Calibrations based on PARAFAC yielded the following values for the decision limit (CCα): 1.16μgL(-1) for BHT, 1.34μgL(-1) for BP, 1.84μgL(-1) for DEHA and 51.42μgL(-1) for DiNP(for α=0.05 and two replicates).

  16. Determining the location of buried plastic water pipes from measurements of ground surface vibration

    Science.gov (United States)

    Muggleton, J. M.; Brennan, M. J.; Gao, Y.

    2011-09-01

    ‘Mapping the Underworld' is a UK-based project, which aims to create a multi-sensor device that combines complementary technologies for remote buried utility service detection and location. One of the technologies to be incorporated in the device is low-frequency vibro-acoustics, and techniques for detecting buried infrastructure, in particular plastic water pipes, are being investigated. One of the proposed techniques involves excitation of the pipe at some known location with concurrent vibrational mapping of the ground surface in order to infer the location of the remainder of the pipe. In this paper, measurements made on a dedicated pipe rig are reported. Frequency response measurements relating vibrational velocity on the ground to the input excitation were acquired. Contour plots of the unwrapped phase revealed the location of the pipe to within 0.1-0.2 m. Magnitude contour plots revealed the excitation point and also the location of the pipe end. By examining the unwrapped phase gradients along a line above the pipe, it was possible to identify the wave-type within the pipe responsible for the ground surface vibration. Furthermore, changes in the ground surface phase speed computed using this method enabled the location of the end of the pipe to be confirmed.

  17. Comparison of detection threshold values determined using glass sniff bottles and plastic squeeze bottles.

    Science.gov (United States)

    Wudarski, Thomas J; Doty, Richard L

    2004-02-01

    Olfactory threshold measures are influenced by such factors as odorant species, diluent type, psychophysical paradigm, and stimulus-presentation procedure. In this study, we compared phenyl ethyl alcohol odor-detection thresholds obtained using 120-ml glass sniff bottles to those obtained using 120-ml plastic squeeze bottles. Although these presentation media are commonly employed in published studies, there has never been a formal comparison of values obtained using them. 10 male and 10 female subjects were tested on two threshold test sessions, one for each type of bottle. Order of sessions was systematically counterbalanced and completed on the same day for a given subject, with a minimum of 30 min. elapsing between sessions. A seven-reversal, single-staircase threshold procedure was employed. Although the threshold values were similar for the two procedures, slightly lower thresholds were obtained using the glass sniff bottles [respective M (SEM) log vol/vol values = -6.61 (.20) and -6.13 (.24)]. These data suggest that, while threshold values using these two presentation procedures can be roughly compared across studies, accurate comparisons may require a slight mathematical adjustment.

  18. Scuttle Flies (Diptera: Phoridae) Inhabiting Rabbit Carcasses Confined to Plastic Waste Bins in Malaysia Include New Records and an Undescribed Species

    Science.gov (United States)

    Zuha, Raja M.; Huong-Wen, See; Disney, R. Henry L.; Omar, Baharudin

    2017-01-01

    Scuttle flies (Diptera: Phoridae) are small-sized insects of forensic importance. They are well known for diversified species and habitats, but in the context of forensic entomology, scuttle flies’ inhabitance of corpses remains inadequately explored. With recent reports indicating the existence of more scuttle fly species possibly inhabiting these environments, a decomposition study using animal carcasses in enclosed environments was conducted. The aim was to record the occurrence of scuttle flies on rabbit carcasses placed in sealed plastic waste bins for a 40-day period. The study was conducted as two replicates in Bangi, Selangor. Sampling was carried out at different time intervals inside a modified mosquito net as a trap. Inside the trap, adult scuttle flies were aspirated and preserved in 70% ethanol. The fly larvae and pupae were reared until their adult stage to facilitate identification. From this study, six scuttle fly species were collected, i.e., Dahliphora sigmoides (Schmitz) ♂, Gymnoptera simplex (Brues) ♀, Megaselia scalaris (Loew) ♂♀, Puliciphora borinquenensis (Wheeler) ♂, Puliciphora obtecta Meijere ♀ and Spiniphora sp. ♀. Both D. sigmoides and P. obtecta were newly recorded in Malaysia, whilst the Spiniphora sp. was considered an unknown species until it was linked to its male counterpart. The sealed waste bins were found to be accessible for the scuttle flies with delayed arrival (day 4–5). Megaselia scalaris was the primary scuttle fly species attracted to the carcass, and its occurrence could be observed between days 4–7 (replicate 1) and days 5–33 (replicate 2). This study also revealed Sarcophaga spp. (Diptera: Sarcophagidae) as the earliest species to colonize the remains and the longest to inhabit them (days 2–40). The larvae of Hermetia illucens (Linneaus) (Diptera: Stratiomyidae) and Fannia sp. (Diptera: Fanniidae) were found on the carcasses during the mid-advanced decay period. These findings expand the

  19. WE(EE) Demand - Recycled Plastic

    OpenAIRE

    Førby, Marie; Pedersen, Jakob; Borgen, Nanna; Hansen, Rasmus Nør

    2015-01-01

    Plastic management – from production to waste – has massive negative effects on the environment of which one of the main problems are the CO2 released from the fossil fuels. The focus of this paper lies on the possibilities of increasing demand for recycled plastics from electric and electronic equipment (WEEE-plastic) through modifications in the Danish waste systems. Due to the chemical build of plastic, it is not possible to reprocess it with mechanical recycle technologies while keeping t...

  20. Creating Methane from Plastics: Recycling at a Lunar Outpost

    Science.gov (United States)

    Captain, Janine; Santiago, Eddie; Wheeler, Ray; Strayer, RIchard; Garland, Jay; Parrish, Clyde

    2010-01-01

    The high cost of re-supply from Earth demands resources to be utilized to the fullest extent for exploration missions. Recycling is a key technology that maximizes the available resources by converting waste products into useful commodities. One example of this is to convert crew member waste such as plastic packaging, food scraps, and human waste, into fuel. The ability to refuel on the lunar surface would reduce the vehicle mass during launch and provide excess payload capability. The goal of this project is to determine the feasibility of recycling waste into methane on the lunar outpost by performing engineering assessments and lab demonstrations of the technology. The first goal of the project was to determine how recycling could influence lunar exploration. Table I shows an estimation of the typical dried waste stream generated each day for a crew of four. Packaging waste accounts for nearly 86% of the dry waste stream and is a significant source of carbon on the lunar surface. This is important because methane (CH4) can be used as fuel and no other source of carbon is available on the lunar surface. With the initial assessment indicating there is sufficient resources in the waste stream to provide refueling capabilities, the project was designed to examine the conversion of plastics into methane.