WorldWideScience

Sample records for plastic ring carriers

  1. The intermetallic bonding between a ring carrier and aluminum piston alloy

    OpenAIRE

    Manasijevic, Srećko; Dolić, Natalija; Djurdjevic, Mile; Mišić, Nataša; Davitkov, Novica

    2015-01-01

    This paper presents the results of investigating the formation of intermetallic bond between a ring carrier and aluminum piston alloy. The ring carrier is made of austenitic cast iron (Ni-Resist) in order to increase the wear resistance of the first ring groove and applied in highly loaded diesel engines. Metallographic examination of the quality of alfin bond was done. A metallographic investigation using an optical microscope in combination with the SEM/EDS analysis of the quality of the in...

  2. The existing situation and challenges regarding the use of plastic carrier bags in Europe.

    Science.gov (United States)

    Kasidoni, Maria; Moustakas, Konstantinos; Malamis, Dimitris

    2015-05-01

    Since day one, retailers and consumers have favoured plastic carrier bags. However, owing to the numerous environmental disadvantages, lightweight plastic carrier bags have been drawing the attention of the European Union competent authorities. Therefore, many European Union member states have taken action so as to reduce the use of plastic carrier bags. Based on the existing legislation and voluntary initiatives for the reduction of lightweight plastic carrier bags, the challenges and achieved outcomes from the implemented policy options in the various European Union member states are discussed and commented regarding the forthcoming transposition of the 'Directive 94/62/EC on packaging and packaging waste to reduce the consumption of lightweight plastic carrier bags' into the European Union member states' national law.

  3. Degradation of plastic carrier bags in the marine environment.

    Science.gov (United States)

    O'Brine, Tim; Thompson, Richard C

    2010-12-01

    There is considerable concern about the hazards that plastic debris presents to wildlife. Use of polymers that degrade more quickly than conventional plastics presents a possible solution to this problem. Here we investigate breakdown of two oxo-biodegradable plastics, compostable plastic and standard polyethylene in the marine environment. Tensile strength of all materials decreased during exposure, but at different rates. Compostable plastic disappeared from our test rig between 16 and 24 weeks whereas approximately 98% of the other plastics remained after 40 weeks. Some plastics require UV light to degrade. Transmittance of UV through oxo-biodegradable and standard polyethylene decreased as a consequence of fouling such that these materials received ∼ 90% less UV light after 40 weeks. Our data indicate that compostable plastics may degrade relatively quickly compared to oxo-biodegradable and conventional plastics. While degradable polymers offer waste management solutions, there are limitations to their effectiveness in reducing hazards associated with plastic debris.

  4. Design consideration for design a flat and ring plastics part using Solidworks software

    Science.gov (United States)

    Amran, M. A. M.; Faizal, K. M.; Salleh, M. S.; Sulaiman, M. A.; Mohamad, E.

    2015-12-01

    Various considerations on design of plastic injection moulded parts were applied in initial stage to prevent any defects of end products. Therefore, the objective of this project is to design the plastic injection moulded part by taking consideration on several factors such as draft angle, corner radius and location of gate. In this project, flat plastic part, ring plastic part, core inserts for flat and ring plastic part were designed using SolidWorks software. The plastic part was drawn in sketching mode then the 3D modeling of solid part was generated using various commands. Considerations of plastic part such as draft angle and corner radius with location of gate was considered in the design stage. Finally, it was successfully designed the two plastic parts with their respectively insert by using SolidWorks software. The flat plastic part and ring plastic part were designed for the purpose for future researches for study the weld lines, meld lines, air trapped and geometrical size of the product. Thus, by designing the flat plastic part and ring plastic part having core insert on each part, the completed mould design of two plate mould can be considered. This is because, plastic injection parts are needed to be designed properly in order to neglect any defect when the mould was made.

  5. The intermetallic bonding between a ring carrier and aluminum piston alloy

    Energy Technology Data Exchange (ETDEWEB)

    Manasijevie, S.; Dolie, N.; Djurdjevic, M.; Misic, N.; Davitkov, N.

    2015-07-01

    This paper presents the results of investigating the formation of intermetallic bond between a ring carrier and aluminum piston alloy. The ring carrier is made of austenitic cast iron (Ni-Resist) in order to increase the wear resistance of the first ring groove and applied in highly loaded diesel engines. Metallographic examination of the quality of al fin bond was done. A metallographic investigation using an optical microscope in combination with the SEM/EDS analysis of the quality of the intermetallic bonding layer was done. The test results show that can be made successfully as well as the formation of metal connection (alfin bond) between the ring carrier and aluminum piston alloy. (Author)

  6. Reduction of plastic carrier bag use: An analysis of alternatives in Israel.

    Science.gov (United States)

    Ayalon, Ofira; Goldrath, Tal; Rosenthal, Gad; Grossman, Michal

    2009-07-01

    Plastic carrier bags have been drawing the attention of the public and politicians. Different policy measures to reduce the environmental burden of these bags have been implemented and more are planned. The research analyzed the actual environmental aspects of consumption and use of plastic carrier bags and assessed the effectiveness of the proposed regulation in Israel. Since plastic bags are provided free of charge, people have a tendency to use these bags excessively, therefore a rigorous educational program should address this trend. However, the environmental load imposed by the bags is more a politically correct issue than an actual environmental hazard, and therefore the means for reducing their use should not include a high levy or total elimination of these bags.

  7. Plastic as a carrier of POPs to aquatic organisms: a model analysis.

    Science.gov (United States)

    Koelmans, Albert A; Besseling, Ellen; Wegner, Anna; Foekema, Edwin M

    2013-07-16

    It has been hypothesized that persistent organic pollutants (POPs) in microplastic may pose a risk to aquatic organisms. Here we develop and analyze a conceptual model that simulates the effects of plastic on bioaccumulation of POPs. The model accounts for dilution of exposure concentration by sorption of POPs to plastic (POP "dilution"), increased bioaccumulation by ingestion of plastic-containing POPs ("carrier"), and decreased bioaccumulation by ingestion of clean plastic ("cleaning"). The model is parametrized for the lugworm Arenicola marina and evaluated against recently published bioaccumulation data for this species from laboratory bioassays with polystyrene microplastic. Further scenarios include polyethylene microplastic, nanosized plastic, and open marine systems. Model analysis shows that plastic with low affinity for POPs such as polystyrene will have a marginal decreasing effect on bioaccumulation, governed by dilution. For stronger sorbents such as polyethylene, the dilution, carrier, and cleaning mechanism are more substantial. In closed laboratory bioassay systems, dilution and cleaning dominate, leading to decreased bioaccumulation. Also in open marine systems a decrease is predicted due to a cleaning mechanism that counteracts biomagnification. However, the differences are considered too small to be relevant from a risk assessment perspective.

  8. Plastic Deformation and Rupture of Ring-Stiffened Cylinders under Localized Pressure Pulse Loading

    Directory of Open Access Journals (Sweden)

    Michelle S. Hoo Fatt

    1994-01-01

    Full Text Available An analytical solution for the dynamic plastic deformation of a ring-stiffened cylindrical shell subject to high intensity pressure pulse loading is presented. By using an analogy between a cylindrical shell that undergoes large plastic deformation and a rigid-plastic string resting on a rigid-plastic foundation, one derives closed-form solutions for the transient and final deflection profiles and fracture initiation of the shell. Discrete masses' and springs are used to describe the ring stiffeners in the stiffened shell. The problem of finding the transient deflection profile of the central bay is reduced to solving an inhomogeneous wave equation with inhomogeneous boundary conditions using the method of eigenfunction expansion. The overall deflection profile consists of both global (stiffener and local (bay components. This division of the shell deflection profile reveals a complex interplay between the motions of the stiffener and the bay. Furthermore, a parametric study on a ring-stiffened shell damaged by a succession of underwater explosions shows that the string-on-foundation model with ring stiffeners described by lumped masses and springs is a promising method of analyzing the structure.

  9. The intermetallic bonding between a ring carrier and aluminum piston alloy

    Directory of Open Access Journals (Sweden)

    Manasijevic, Srećko

    2015-09-01

    Full Text Available This paper presents the results of investigating the formation of intermetallic bond between a ring carrier and aluminum piston alloy. The ring carrier is made of austenitic cast iron (Ni-Resist in order to increase the wear resistance of the first ring groove and applied in highly loaded diesel engines. Metallographic examination of the quality of alfin bond was done. A metallographic investigation using an optical microscope in combination with the SEM/EDS analysis of the quality of the intermetallic bonding layer was done. The test results show that can be made successfully as well as the formation of metal connection (alfin bond between the ring carrier and aluminum piston alloy.El artículo presenta los resultados de la investigación sobre la formación de una unión intermetálica entre el portasegmento y la aleación de aluminio del pistón. El portasegmento es una fundición de hierro austenítico (Ni-Resist con el fin de aumentar la resistencia al desgaste de la unión Al-fin del primer segmento y se utiliza en motores diésel altamente cargados. Se realizó un examen metalográfico de la unión intermetálica, mediante un microscopio óptico en combinación con SEM/EDS. Los satisfactorios resultados obtenidos muestran la formación de contacto metálico (unión Al-fin del primer segmento entre el portasegmento y la aleación de aluminio del pistón.

  10. Carrier transfer in vertically stacked quantum ring-quantum dot chains

    Energy Technology Data Exchange (ETDEWEB)

    Mazur, Yu. I., E-mail: ymazur@uark.edu; Dorogan, V. G.; Benamara, M.; Salamo, G. J. [Arkansas Institute for Nanoscale Materials Science and Engineering, University of Arkansas, Fayetteville, Arkansas 72701 (United States); Lopes-Oliveira, V.; Lopez-Richard, V.; Teodoro, M. D.; Marques, G. E. [Departamento de Fisica, Universidade Federal de São Carlos, 13565-905 São Carlos, São Paulo (Brazil); Souza, L. D. de [Departamento de Fisica, Universidade Federal de São Carlos, 13565-905 São Carlos, São Paulo (Brazil); Arkansas Institute for Nanoscale Materials Science and Engineering, University of Arkansas, Fayetteville, Arkansas 72701 (United States); Wu, J.; Wang, Z. M. [State Key Laboratory of Electronic Thin Film and Integrated Devices, University of Electronic Science and Technology of China, Chengdu (China); Tarasov, G. G. [Institute of Semiconductor Physics, National Academy of Sciences, pr. Nauki 45, Kiev 03028 (Ukraine); Marega, E. [Instituto de Fisica de São Carlos, Universidade de São Paulo, 13.566-590 São Carlos, São Paulo (Brazil)

    2015-04-21

    The interplay between structural properties and charge transfer in self-assembled quantum ring (QR) chains grown by molecular beam epitaxy on top of an InGaAs/GaAs quantum dot (QD) superlattice template is analyzed and characterized. The QDs and QRs are vertically stacked and laterally coupled as well as aligned within each layer due to the strain field distributions that governs the ordering. The strong interdot coupling influences the carrier transfer both along as well as between chains in the ring layer and dot template structures. A qualitative contrast between different dynamic models has been developed. By combining temperature and excitation intensity effects, the tuning of the photoluminescence gain for either the QR or the QD mode is attained. The information obtained here about relaxation parameters, energy scheme, interlayer and interdot coupling resulting in creation of 1D structures is very important for the usage of such specific QR–QD systems for applied purposes such as lasing, detection, and energy-harvesting technology of future solar panels.

  11. Carrier transfer in vertically stacked quantum ring-quantum dot chains

    Science.gov (United States)

    Mazur, Yu. I.; Lopes-Oliveira, V.; de Souza, L. D.; Lopez-Richard, V.; Teodoro, M. D.; Dorogan, V. G.; Benamara, M.; Wu, J.; Tarasov, G. G.; Marega, E.; Wang, Z. M.; Marques, G. E.; Salamo, G. J.

    2015-04-01

    The interplay between structural properties and charge transfer in self-assembled quantum ring (QR) chains grown by molecular beam epitaxy on top of an InGaAs/GaAs quantum dot (QD) superlattice template is analyzed and characterized. The QDs and QRs are vertically stacked and laterally coupled as well as aligned within each layer due to the strain field distributions that governs the ordering. The strong interdot coupling influences the carrier transfer both along as well as between chains in the ring layer and dot template structures. A qualitative contrast between different dynamic models has been developed. By combining temperature and excitation intensity effects, the tuning of the photoluminescence gain for either the QR or the QD mode is attained. The information obtained here about relaxation parameters, energy scheme, interlayer and interdot coupling resulting in creation of 1D structures is very important for the usage of such specific QR-QD systems for applied purposes such as lasing, detection, and energy-harvesting technology of future solar panels.

  12. Novel drug delivery carrier from alginate-carrageenan and glycerol as plasticizer

    Science.gov (United States)

    Darmokoesoemo, Handoko; Pudjiastuti, Pratiwi; Rahmatullah, Bagus; Kusuma, Heri Septya

    Drug delivery carriers are materials that can be used to administer drugs into the human body. Alginate and carrageenan are natural polymers that have potential as drug delivery material. Therefore in this study conducted a new innovation using carrageenan and alginates from extract of red seaweed and brown seaweed as base materials of capsule. This is expected to improve the quality of the used materials so it's easier to obtain the capsule with base material from carrageenan-alginate that has good quality as drug delivery carrier. Moreover, in the manufacture of capsules from carrageenan and alginates also added plasticizers in order to maintain the elasticity and the swelling degree of the capsules are made so that the capsules are not brittle. In addition, in this study used glycerol because it is a useful plasticizer to increase the plasticity of a material by filling the cavities between monomers. The capsules were prepared with four variations of glycerol concentration are A, B, C and D. In these capsule was analyzed of surface morphology with SEM, test of swelling degree and test of dissolution kinetics for some acidity level. Analysis of surface morphology with SEM shows that the capsule shell has very small pores. The average of swelling degree for capsules A, B, C and D are 452.4%, 599.0%, 730.66% and 731.25%, respectively. FTIR analysis shows that the presence of glycerol can increase the number of hydrogen bonds that are formed. The acidity level affects the dissolution profile of each capsules. In general with an increasingly alkaline environment causes all the capsules will be easier to release. This is because the increasing of acidic groups in the copolymer causes the capsule to be more easily occur neutralization reaction in a more alkaline environment so that the disintegration of capsules can occur more quickly. In addition from this study also can be seen that the increasing concentration of glycerol can cause the rate of capsule dissolution

  13. Biohydrogen production from glucose in upflow biofilm reactors with plastic carriers under extreme thermophilic conditions (70(degree)C)

    DEFF Research Database (Denmark)

    Zheng, H.; Zeng, Raymond Jianxiong; Angelidaki, Irini

    2008-01-01

    Biohydrogen could efficiently be produced in glucose-fed biofilm reactors filled with plastic carriers and operated at 70°C. Batch experiments were, in addition, conducted to enrich and cultivate glucose-fed extremethermophilic hydrogen producing microorganisms from a biohydrogen CSTR reactor fed...... with household solid waste. Kinetic analysis of the biohydrogen enrichment cultures show that substrate (glucose) likely inhibited hydrogen production when its concentration was higher than 1 g/L. Different start up strategies were applied for biohydrogen production in biofilm reactors operated at 70°C, and fed...... with synthetic medium with glucose as the only carbon and energy source. A biofilm reactor, started up with plastic carriers, that were previously inoculated with the enrichment cultures, resulted in higher hydrogen yield (2.21 mol H2/mol glucose consumed) but required longer start up time (1 month), while...

  14. Application of Carrier and Plasticizer to Improve the Dissolution and Bioavailability of Poorly Water-Soluble Baicalein by Hot Melt Extrusion

    National Research Council Canada - National Science Library

    Zhang, Yilan; Luo, Rui; Chen, Yi; Ke, Xue; Hu, Danrong; Han, Miaomiao

    2014-01-01

    ...) to prepare solid dispersions using hot melt extrusion (HME). Proper carriers and plasticizers were selected by calculating the Hansen solubility parameters, evaluating melting processing condition, and measuring the solubility of obtained melts...

  15. The Portuguese plastic carrier bag tax: The effects on consumers' behavior.

    Science.gov (United States)

    Martinho, Graça; Balaia, Natacha; Pires, Ana

    2017-03-01

    Marine litter from lightweight plastic bags is a global problem that must be solved. A plastic bag tax was implemented in February 2015 to reduce the consumption of plastic grocery bags in Portugal and in turn reduce the potential contribution to marine litter. This study analyzes the effect of the plastic bag tax on consumer behavior to learn how it was received and determine the perceived effectiveness of the tax 4months after its implementation. In addition, the study assessed how proximity to coastal areas could influence behaviors and opinions. The results showed a 74% reduction of plastic bag consumption with a simultaneously 61% increase of reusable plastic bags after the tax was implemented. Because plastic bags were then reused for shopping instead of garbage bags, however, the consumption of garbage bags increased by 12%. Although reduction was achieved, the tax had no effect on the perception of marine litter or the impact of plastic bags on environment and health. The majority of respondents agree with the tax but view it as an extra revenue to the State. The distance to the coast had no meaningful influence on consumer behavior or on the perception of the tax. Although the tax was able to promote the reduction of plastics, the role of hypermarkets and supermarkets in providing alternatives through the distribution of reusable plastic bags was determinant to ensuring the reduction.

  16. Biohydrogen production from glucose in upflow biofilm reactors with plastic carriers under extreme thermophilic conditions (70 degrees C).

    Science.gov (United States)

    Zheng, Hang; Zeng, Raymond J; Angelidaki, Irini

    2008-08-01

    Biohydrogen could efficiently be produced in glucose-fed biofilm reactors filled with plastic carriers and operated at 70 degrees C. Batch experiments were, in addition, conducted to enrich and cultivate glucose-fed extreme-thermophilic hydrogen producing microorganisms from a biohydrogen CSTR reactor fed with household solid waste. Kinetic analysis of the biohydrogen enrichment cultures show that substrate (glucose) likely inhibited hydrogen production when its concentration was higher than 1 g/L. Different start up strategies were applied for biohydrogen production in biofilm reactors operated at 70 degrees C, and fed with synthetic medium with glucose as the only carbon and energy source. A biofilm reactor, started up with plastic carriers, that were previously inoculated with the enrichment cultures, resulted in higher hydrogen yield (2.21 mol H(2)/mol glucose consumed) but required longer start up time (1 month), while a biofilm reactor directly inoculated with the enrichment cultures reached stable state much faster (8 days) but with very low hydrogen yield (0.69 mol H(2)/mol glucose consumed). These results indicate that hydraulic pressure is necessary for successful immobilization of bacteria on carriers, while there is the risk of washing out specific high yielding bacteria.

  17. Effect of Doping Position on the Active Silicon-on-Insulator Micro-Ring Resonator Based on Free Carrier Injection

    Directory of Open Access Journals (Sweden)

    B. Mardiana

    2012-01-01

    Full Text Available Problem statement: Metal interconnects have become significant limitation on the scaling of CMOS technologies in electronics integrated circuit. Silicon photonics has offers great potential to overcome this critical bottleneck due to the advantages of optical interconnects. Silicon-based optical micro-ring resonator is promising basic element of future electronic-photonic integrated circuits because of its wide applications on photonic devices such as modulator, switch and sensor. Approach: This study highlights the study of the free carrier injection effect on the active SOI micro-ring resonator. The effect of the free carrier injection on micro-ring resonator is evaluated by varying the p+ and n+ doping position. Device performances are predicted using numerical modeling software 2D SILVACO as well as Finite Difference Time Domain (FDTD simulation software, RSOFT. Results: The results show that the refractive index change increases as the p+ and n+ doping position become closer to the rib waveguide. A shift in resonant wavelength of around 2 and 3 nm was is predicted at 0.9V drive forward voltage for 0.5 and 1.0 μm gap distance between p+ and n+ doping regions and the sidewall of the rib waveguide. It is also shown that 10 and 9.2 dB maximum change of the output response obtained through the output of the transmission spectrum of the device with gap 0.5 and 1.0 μm. Conclusion: The closer distance between p+ and n+ doping regions and the rib waveguide has optimal shift of resonance wavelength and better extinction ratio of transmission spectrum.

  18. Using Brillouin fiber-optic ring laser to provide base station with uplink optical carrier in a 10 GHz radio over fiber system

    Institute of Scientific and Technical Information of China (English)

    CHEN Hao-shuo; LIN Ru-jian; YE Jia-jun

    2009-01-01

    In this paper, a 10 GHz radio over fiber system is analyzed. The Brillouin fiber-optic ring laser is used in the center station (CS) to suppress the optical carrier for the modulation depth enhancement. Simultaneously, the Stockes waveinduced by the Brillouin amplification injects and locks the Fabry-Perot (FP) laser to output a signal-mode optical source,which works as the uplink optical carrier.

  19. Conformational Plasticity in Glycomimetics: Fluorocarbamethyl-L-idopyranosides Mimic the Intrinsic Dynamic Behaviour of Natural Idose Rings.

    Science.gov (United States)

    Unione, Luca; Xu, Bixue; Díaz, Dolores; Martín-Santamaría, Sonsoles; Poveda, Ana; Sardinha, João; Rauter, Amelia Pilar; Blériot, Yves; Zhang, Yongmin; Cañada, F Javier; Sollogoub, Matthieu; Jiménez-Barbero, Jesus

    2015-07-13

    Sugar function, structure and dynamics are intricately correlated. Ring flexibility is intrinsically related to biological activity; actually plasticity in L-iduronic rings modulates their interactions with biological receptors. However, the access to the experimental values of the energy barriers and free-energy difference for conformer interconversion in water solution has been elusive. Here, a new generation of fluorine-containing glycomimetics is presented. We have applied a combination of organic synthesis, NMR spectroscopy and computational methods to investigate the conformational behaviour of idose- and glucose-like rings. We have used low-temperature NMR spectroscopic experiments to slow down the conformational exchange of the idose-like rings. Under these conditions, the exchange rate becomes slow in the (19) F NMR spectroscopic chemical shift timescale and allows shedding light on the thermodynamic and kinetic features of the equilibrium. Despite the minimal structural differences between these compounds, a remarkable difference in their dynamic behaviour indeed occurs. The importance of introducing fluorine atoms in these sugars mimics is also highlighted. Only the use of (19) F NMR spectroscopic experiments has permitted the unveiling of key features of the conformational equilibrium that would have otherwise remained unobserved.

  20. Plastic as a Carrier of POPs to Aquatic Organisms: A Model Analysis

    NARCIS (Netherlands)

    Koelmans, A.A.; Besseling, E.; Wegner, A.; Foekema, E.M.

    2013-01-01

    It has been hypothesized that persistent organic pollutants (POPs) in microplastic may pose a risk to aquatic organisms. Here we develop and analyze a conceptual model that simulates the effects of plastic on bioaccumulation of POPs. The model accounts for dilution of exposure concentration by sorpt

  1. Reconfigurable electro-optical directed-logic circuit using carrier-depletion micro-ring resonators.

    Science.gov (United States)

    Qiu, Ciyuan; Gao, Weilu; Soref, Richard; Robinson, Jacob T; Xu, Qianfan

    2014-12-15

    Here we demonstrate a reconfigurable electro-optical directed-logic circuit based on a regular array of integrated optical switches. Each 1×1 optical switch consists of a micro-ring resonator with an embedded lateral p-n junction and a micro-heater. We achieve high-speed on-off switching by applying electrical logic signals to the p-n junction. We can configure the operation mode of each switch by thermal tuning the resonance wavelength. The result is an integrated optical circuit that can be reconfigured to perform any combinational logic operation. As a proof-of-principle, we fabricated a multi-spectral directed-logic circuit based on a fourfold array of switches and showed that this circuit can be reconfigured to perform arbitrary two-input logic functions with speeds up to 3  GB/s.

  2. Studying global change through investigation of the plastic responses of xylem anatomy in tree rings.

    Science.gov (United States)

    Fonti, Patrick; von Arx, Georg; García-González, Ignacio; Eilmann, Britta; Sass-Klaassen, Ute; Gärtner, Holger; Eckstein, Dieter

    2010-01-01

    Variability in xylem anatomy is of interest to plant scientists because of the role water transport plays in plant performance and survival. Insights into plant adjustments to changing environmental conditions have mainly been obtained through structural and functional comparative studies between taxa or within taxa on contrasting sites or along environmental gradients. Yet, a gap exists regarding the study of hydraulic adjustments in response to environmental changes over the lifetimes of plants. In trees, dated tree-ring series are often exploited to reconstruct dynamics in ecological conditions, and recent work in which wood-anatomical variables have been used in dendrochronology has produced promising results. Environmental signals identified in water-conducting cells carry novel information reflecting changes in regional conditions and are mostly related to short, sub-annual intervals. Although the idea of investigating environmental signals through wood anatomical time series goes back to the 1960s, it is only recently that low-cost computerized image-analysis systems have enabled increased scientific output in this field. We believe that the study of tree-ring anatomy is emerging as a promising approach in tree biology and climate change research, particularly if complemented by physiological and ecological studies. This contribution presents the rationale, the potential, and the methodological challenges of this innovative approach.

  3. Evaluation of Lumicyano™ cyanoacrylate fuming process for the development of latent fingermarks on plastic carrier bags by means of a pseudo operational comparative trial.

    Science.gov (United States)

    Farrugia, Kevin J; Deacon, Paul; Fraser, Joanna

    2014-03-01

    There are a number of studies discussing recent developments of a one-step fluorescent cyanoacrylate process. This study is a pseudo operational trial to compare an example of a one-step fluorescent cyanoacrylate product, Lumicyano™, with the two recommended techniques for plastic carrier bags; cyanoacrylate fuming followed by basic yellow 40 (BY40) dyeing and powder suspensions. 100 plastic carrier bags were collected from the place of work and the items were treated as found without any additional fingermark deposition. The bags were split into three and after treatment with the three techniques a comparable number of fingermarks were detected by each technique (average of 300 fingermarks). The items treated with Lumicyano™ were sequentially processed with BY40 and an additional 43 new fingermarks were detected. Lumicyano™ appears to be a suitable technique for the development of fingermarks on plastic carrier bags and it can help save lab space and time as it does not require dyeing or drying procedures. Furthermore, contrary to other one-step cyanoacrylate products, existing cyanoacrylate cabinets do not require any modification for the treatment of articles with Lumicyano™. To date, there is little peer reviewed articles in the literature on trials related to Lumicyano™ and this study aims to contribute to fill this gap.

  4. 聚氨酯泡沫塑料填料的改性试验研究%Experimental Study on Modification of Polyurethane Foam Plastics Carriers

    Institute of Scientific and Technical Information of China (English)

    成国栋; 王芬; 李超; 汪泳; 赵贞地; 季民

    2012-01-01

    The conventional polyurethane foam plastic carrier was modified by chemical oxidation and gelatin protein grafting technology, and the surface physicochemical properties of the carrier, the speed of biofilm formation, the quantity of biofilm and the performance in treating wastewater were investigated before and after the modification. The results showed that the ratio of C - 0 bond on surface of the modified carrier was increased by 47. 86% , and the ratios of C - C and C - H bonds on surface of the modified carrier were reduced by 50. 66%. Hydrophilicity and surface roughness of the carrier were increased after the modification. Compared with the original carrier, the quantity of biofilm on the modified carrier was increased by 30% , the average growth rate of biofilm was increased by 47% , and the removal rates of COD and ammonia nitrogen were increased.%采用化学氧化-明胶蛋白接枝技术对普通聚氨酯泡沫塑料填料进行改性,并对改性前后填料的表面特性、挂膜速度、生物膜量及除污性能等进行研究.结果发现,改性填料表面的C-O键所占比例提高了47.86%,C-C、C-H键所占比例下降了50.66%;改性填料的表面粗糙度以及亲水性提高;与未改性填料相比,改性填料的生物膜量提高了30%,生物膜量的平均增长速率提高了47%;与未改性填料相比,改性填料对COD和氨氮的去除率均有所提高.

  5. No-carrier-added (NCA) aryl [{sup 18}F]fluorides via the nucleophilic aromatic substitution of electron rich aromatic rings

    Energy Technology Data Exchange (ETDEWEB)

    Ding, Yu-Shin; Fowler, J.S.; Wolf, A.P.

    1991-12-31

    A method for synthesizing no-carrier-added (NCA) aryl [{sup 18}F] fluoride substituted aromatic aldehyde compositions bearing an electron donating group is described. The method includes the step of reacting aromatic nitro aldehydes having a suitably protected hydroxyl substituent on an electron rich ring. The reaction is carried out by nucleophilic aromatic substitution with a no-carrier-added (NCA) [{sup 18}F]fluoride ion. The method can be used to synthesize various no-carrier-added aryl [{sup 18}F]fluoride compositions, including 6-[{sup 18}F]fluoro-L-DOPA, 2-[{sup 18}F]fluorotyrosine, 6-[{sup 18}F]fluoronorepinephrine, and 6-[{sup 18}F]fluorodopamine. In those instances when a racemic mixture of enantiomers is produced by the present invention, such as in the synthesis of 6-[{sup 18}F]fluoronorepinephrine, a preferred method also includes resolution of the racemic mixture on a chiral HPLC column. This procedure results in a high yield of enantiomerically pure [{sup 18}F] labeled isomers, for example [-]-6-[{sup 18}F]fluoronorepinephrine and [+]-6-[{sup 18}F]fluoronorepinephrine.

  6. Standard test method for ranking resistance of plastics to sliding wear using block-on-ring wear test—cumulative wear method

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2003-01-01

    1.1 This test method covers laboratory procedures for determining the resistance of plastics to sliding wear. The test utilizes a block-on-ring friction and wear testing machine to rank plastics according to their sliding wear characteristics against metals or other solids. 1.2 An important attribute of this test is that it is very flexible. Any material that can be fabricated into, or applied to, blocks and rings can be tested. Thus, the potential materials combinations are endless. In addition, the test can be run with different gaseous atmospheres and elevated temperatures, as desired, to simulate service conditions. 1.3 Wear test results are reported as the volume loss in cubic millimetres for the block and ring. Materials of higher wear resistance will have lower volume loss. 1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with it...

  7. Application of carrier and plasticizer to improve the dissolution and bioavailability of poorly water-soluble baicalein by hot melt extrusion.

    Science.gov (United States)

    Zhang, Yilan; Luo, Rui; Chen, Yi; Ke, Xue; Hu, Danrong; Han, Miaomiao

    2014-06-01

    The objective of this study was to develop a suitable formulation for baicalein (a poorly water-soluble drug exhibiting high melting point) to prepare solid dispersions using hot melt extrusion (HME). Proper carriers and plasticizers were selected by calculating the Hansen solubility parameters, evaluating melting processing condition, and measuring the solubility of obtained melts. The characteristic of solid dispersions prepared by HME was evaluated. The dissolution performance of the extrudates was compared to the pure drug and the physical mixtures. Physicochemical properties of the extrudates were characterized by differential scanning calorimetry (DSC), powder X-ray diffraction (PXRD), and Fourier transform infrared spectroscopy (FTIR). Relative bioavailability after oral administration in beagle dogs was assessed. As a result, Kollidon VA64 and Eudragit EPO were selected as two carriers; Cremophor RH was used as the plasticizer. The dissolution of all the extrudates was significantly improved. DSC and PXRD results suggested that baicalein in the extrudates was amorphous. FTIR spectroscopy revealed the interaction between drug and polymers. After oral administration, the relative bioavailability of solid dispersions with VA64 and EPO was comparative, about 2.4- and 2.9-fold greater compared to the pure drug, respectively.

  8. Amphiphilic block copolymers bearing six-membered ortho ester ring in side chains as potential drug carriers: synthesis, characterization, and in vivo toxicity evaluation.

    Science.gov (United States)

    Luo, Shi; Tao, Yangyang; Tang, Rupei; Wang, Rui; Ji, Weihang; Wang, Chun; Zhao, Youliang

    2014-07-01

    A new type of amphiphilic block copolymers, poly(ethylene glycol)-block-poly(2-methyl-acrylicacid 2-methoxy-5-methyl-[1,3]dioxin-5-ylmethyl ester) (PEG-b-PMME), bearing acid-labile six-membered ortho ester rings in side chains was synthesized by reversible addition-fragmentation chain-transfer polymerization, and the influence of chain length of the hydrophobic PMME block on micelle properties was investigated. The PEG-b-PMME micelles were stable in aqueous buffer at physiological pH with a low critical micelle concentration. Nile Red as a model drug was encapsulated into the micelles to explore the release profiles. The Nile Red-loaded polymeric micelles showed rapid release of Nile Red in weakly acidic environments (pH 5) but slow release under physiological condition (pH 7.4), due to different hydrolysis rate of ortho ester side chains of PEG-b-PMME. The Paclitaxel (PTX)-loaded micelles retained potency in killing lung cancer cells (A549), compared with the free PTX. No obvious toxicity was found in vitro and in vivo after intraperitoneal injection of the micelles, which confirms that the PEG-b-PMME micelles with unique acid-labile characteristic have great potential as nano-scaled carriers for drug delivery.

  9. Plastic condoms.

    Science.gov (United States)

    1968-01-01

    Only simple equipment, simple technology and low initial capital investment are needed in their manufacture. The condoms can be made by people who were previously unskilled or only semi-skilled workers. Plastic condoms differ from those made of latex rubber in that the nature of the plastic film allows unlimited shelf-life. Also, the plastic has a higher degree of lubricity than latex rubber; if there is a demand for extra lubrication in a particular market, this can be provided. Because the plastic is inert, these condoms need not be packaged in hermetically sealed containers. All these attributes make it possible to put these condoms on the distributors' shelves in developing countries competitively with rubber condoms. The shape of the plastic condom is based on that of the lamb caecum, which has long been used as luxury-type condom. The plastic condom is made from plastic film (ethylene ethyl acrilate) of 0.001 inch (0.0254 mm.) thickness. In addition, a rubber ring is provided and sealed into the base of the condom for retention during coitus. The advantage of the plastic condom design and the equipment on which it is made is that production can be carried out either in labour-intensive economy or with varying degrees of mechanization and automation. The uniform, finished condom if made using previously untrained workers. Training of workers can be done in a matter of hours on the two machines which are needed to produce and test the condoms. The plastic film is provided on a double wound roll, and condom blanks are prepared by means of a heat-sealing die on the stamping machine. The rubber rings are united to the condom blanks on an assembly machine, which consists of a mandrel and heat-sealing equipment to seal the rubber ring to the base of the condom. Built into the assembly machine is a simple air-testing apparatus that can detect the smallest pinhole flaw in a condom. The manufacturing process is completed by unravelling the condom from the assembly

  10. Spin Polarization of Carriers in InGaAs Self-Assembled Quantum Rings Inserted in GaAs-AlGaAs Resonant Tunneling Devices

    Science.gov (United States)

    Orsi Gordo, V.; Gobato, Y. Galvão; Galeti, H. V. A.; Brasil, M. J. S. P.; Taylor, D.; Henini, M.

    2017-03-01

    In this work, we have investigated transport and polarization resolved photoluminescence (PL) of n-type GaAs-AlGaAs resonant tunneling diodes (RTDs) containing a layer of InGaAs self-assembled quantum rings (QRs) in the quantum well (QW). All measurements were performed under applied voltage, magnetic fields up to 15 T and using linearly polarized laser excitation. It was observed that the QRs' PL intensity and the circular polarization degree (CPD) oscillate periodically with applied voltage under high magnetic fields at 2 K. Our results demonstrate an effective voltage control of the optical and spin properties of InGaAs QRs inserted into RTDs.

  11. Vascular ring

    Science.gov (United States)

    ... subclavian and left ligamentum ateriosus; Congenital heart defect - vascular ring; Birth defect heart - vascular ring ... Vascular ring is rare. It accounts for less than 1% of all congenital heart problems. The condition ...

  12. Plastic Surgery

    Science.gov (United States)

    ... Surgery? A Week of Healthy Breakfasts Shyness Plastic Surgery KidsHealth > For Teens > Plastic Surgery Print A A ... forehead lightened with a laser? What Is Plastic Surgery? Just because the name includes the word "plastic" ...

  13. Aircraft Carriers

    DEFF Research Database (Denmark)

    Nødskov, Kim; Kværnø, Ole

    There are many indications that China is actively researching the design of an aircraft carrier. It is unknown whether China will initiate the actual acquisition of a carrier, but the indications that are available of their research into aircraft carriers and carrier-capable aircraft, as well...... as their purchases of aircraft carrier systems, makes it more than likely that the country is preparing such an acquisition. China has territorial disputes in the South China Sea over the Spratly Islands and is also worried about the security of its sea lines of communications, by which China transports the majority...... of its foreign trade, as well as its oil imports, upon which the country is totally dependent. China therefore has good reasons for acquiring an aircraft carrier to enable it to protect its national interests. An aircraft carrier would also be a prominent symbol of China’s future status as a great power...

  14. Ring blowers. Ring blower

    Energy Technology Data Exchange (ETDEWEB)

    Nakahara, Y.; Okamura, T.; Takahashi, M. (Fuji Electric Co. Ltd., Tokyo (Japan))

    1991-06-10

    Features, structures and several products of ring blowers were outlined. The ring blower is featured by its medium characteristics because it is higher in air pressure than a turboblower and larger in airflow than a vane blower, and it is applicable flexibly to not only air blasting but various industrial fields such as suction transfer. As several products corresponding to various fields, the followings were outlined: the low noise type with optimum shapes of inlet, outlet and casing cover for reducing noises by 10 dB or more, the heat resistant, water-tight and explosion-proof types suitable for severe environmental conditions, the multi-voltage type for every country served at different voltages, the high air pressure type with two pressure rise stages, and the large airflow type with a wide impeller. In addition, as special use products, the glass fiber reinforced unsatulated polyester ring blower for respiration apparatus, and the variable speed blushless DC motor-driven one for medical beds were outlined. 2 refs., 9 figs., 1 tab.

  15. Saturn's Rings

    Science.gov (United States)

    Cuzzi, J. N.

    2014-12-01

    The rings are changing before our eyes; structure varies on all timescales and unexpected things have been discovered. Many questions have been answered, but some answers remain elusive (see Cuzzi et al 2010 for a review). Here we highlight the major ring science progress over the mission to date, and describe new observations planned for Cassini's final three years. Ring Composition and particle sizes: The rings are nearly all water ice with no other ices - so why are they reddish? The C Ring and Cassini Division are "dirtier" than the more massive B and A Rings, as shown by near-IR and, recently, microwave observations. Particle sizes, from stellar and radio occultations, vary from place to place. Ring structure, micro and macro: numerous spiral density waves and ubiquitous "self-gravity wakes" reveal processes which fostered planet formation in the solar system and elsewhere. However, big puzzles remain regarding the main ring divisions, the C Ring plateau structures, and the B Ring irregular structure. Moonlets, inside and out, seen and unseen: Two gaps contain sizeable moonlets, but more gaps seem to contain none; even smaller embedded "propeller" objects wander, systematically or randomly, through the A ring. Rubble pile ringmoons just outside the rings may escaped from the rings, and the recently discovered "Peggy" may be trying this as we watch. Impact bombardment of the rings: Comet fragments set the rings to rippling on century-timescales, and boulders crash through hourly; meanwhile, the constant hail of infalling Kuiper belt material has a lower mass flux than previously thought. Origin and Age of the Rings: The ring mass and bombardment play key roles. The ring mass is well known everywhere but in the B Ring (where most of it is). New models suggest how tidal breakup of evolving moons may have formed massive ancient rings, of which the current ring is just a shadow. During its last three years, the Cassini tour profile will allow entirely new

  16. Mechanics of Forming Ring Disks

    Directory of Open Access Journals (Sweden)

    Avakyan R.M.

    2010-12-01

    Full Text Available The analysis of forming ring disk of constant thickness in conditions of large plastic deformations taking into account the interconnected change of effective strain and deformation hardening is carried out. The analytical dependences characterizing the relative size of plastic area are obtained. The interrelation between the initial and final form of a product is established at maximum possible size of internal pressure.

  17. Vortex rings

    Energy Technology Data Exchange (ETDEWEB)

    Akhmetov, D.G. [Lavrentiev Institute of Hydrodynamics, Novosibirsk (Russian Federation)

    2009-07-01

    This book presents a comprehensive coverage of the wide field of vortex rings. The book presents the results of systematic experimental investigations, theoretical foundation, as well as the practical applications of vortex rings, such as the extinction of fires at gushing gas and oil wells. All the basic properties of vortex rings as well as their hydrodynamic structures are presented. Special attention is paid to the formation and motion of turbulent vortex rings. (orig.)

  18. Providing resilience for carrier ethernet multicast traffic

    DEFF Research Database (Denmark)

    Ruepp, Sarah Renée; Wessing, Henrik; Zhang, Jiang

    2009-01-01

    This paper presents an overview of the Carrier Ethernet technology with specific focus on resilience. In particular, we detail how multicast traffic, which is essential for e.g. IPTV can be protected. We present Carrier Ethernet resilience methods for linear and ring networks and show by simulation...... that the availability of a multicast connection can be significantly increased by applying relevant resilience techniques....

  19. Providing resilience for carrier ethernet multicast traffic

    DEFF Research Database (Denmark)

    Ruepp, Sarah Renée; Wessing, Henrik; Zhang, Jiang

    2009-01-01

    This paper presents an overview of the Carrier Ethernet technology with specific focus on resilience. In particular, we detail how multicast traffic, which is essential for e.g. IPTV can be protected. We present Carrier Ethernet resilience methods for linear and ring networks and show by simulation...

  20. Ring theory

    CERN Document Server

    Rowen, Louis H

    1991-01-01

    This is an abridged edition of the author's previous two-volume work, Ring Theory, which concentrates on essential material for a general ring theory course while ommitting much of the material intended for ring theory specialists. It has been praised by reviewers:**""As a textbook for graduate students, Ring Theory joins the best....The experts will find several attractive and pleasant features in Ring Theory. The most noteworthy is the inclusion, usually in supplements and appendices, of many useful constructions which are hard to locate outside of the original sources....The audience of non

  1. Plasticity theory

    CERN Document Server

    Lubliner, Jacob

    2008-01-01

    The aim of Plasticity Theory is to provide a comprehensive introduction to the contemporary state of knowledge in basic plasticity theory and to its applications. It treats several areas not commonly found between the covers of a single book: the physics of plasticity, constitutive theory, dynamic plasticity, large-deformation plasticity, and numerical methods, in addition to a representative survey of problems treated by classical methods, such as elastic-plastic problems, plane plastic flow, and limit analysis; the problem discussed come from areas of interest to mechanical, structural, and

  2. Planetary Rings

    CERN Document Server

    Tiscareno, Matthew S

    2011-01-01

    Planetary rings are the only nearby astrophysical disks, and the only disks that have been investigated by spacecraft. Although there are significant differences between rings and other disks, chiefly the large planet/ring mass ratio that greatly enhances the flatness of rings (aspect ratios as small as 1e-7), understanding of disks in general can be enhanced by understanding the dynamical processes observed at close-range and in real-time in planetary rings. We review the known ring systems of the four giant planets, as well as the prospects for ring systems yet to be discovered. We then review planetary rings by type. The main rings of Saturn comprise our system's only dense broad disk and host many phenomena of general application to disks including spiral waves, gap formation, self-gravity wakes, viscous overstability and normal modes, impact clouds, and orbital evolution of embedded moons. Dense narrow rings are the primary natural laboratory for understanding shepherding and self-stability. Narrow dusty...

  3. Planetary Rings

    Science.gov (United States)

    Cuzzi, Jeffrey N.

    1994-01-01

    Just over two decades ago, Jim Pollack made a critical contribution to our understanding of planetary ring particle properties, and resolved a major apparent paradox between radar reflection and radio emission observations. At the time, particle properties were about all there were to study about planetary rings, and the fundamental questions were, why is Saturn the only planet with rings, how big are the particles, and what are they made of? Since then, we have received an avalanche of observations of planetary ring systems, both from spacecraft and from Earth. Meanwhile, we have seen steady progress in our understanding of the myriad ways in which gravity, fluid and statistical mechanics, and electromagnetism can combine to shape the distribution of the submicron-to-several-meter size particles which comprise ring systems into the complex webs of structure that we now know them to display. Insights gained from studies of these giant dynamical analogs have carried over into improved understanding of the formation of the planets themselves from particle disks, a subject very close to Jim's heart. The now-complete reconnaissance of the gas giant planets by spacecraft has revealed that ring systems are invariably found in association with families of regular satellites, and there is ark emerging perspective that they are not only physically but causally linked. There is also mounting evidence that many features or aspects of all planetary ring systems, if not the ring systems themselves, are considerably younger than the solar system

  4. Plastic Jellyfish.

    Science.gov (United States)

    Moseley, Christine

    2000-01-01

    Presents an environmental science activity designed to enhance students' awareness of the hazards of plastic waste for wildlife in aquatic environments. Discusses how students can take steps to reduce the effects of plastic waste. (WRM)

  5. SUPRAMITRAL RING

    Directory of Open Access Journals (Sweden)

    Rajesh G

    2011-11-01

    Full Text Available Supra mitral ring is a rare cause for congenital mitral valve obstr uction. The reported incidence of supramitral ring is 0.2-0.4% in general population and 8% in patients with congenital mitral valve disease. The condition is characterized by an abnormal ridge of connective tissue often circumferential in shape ,on the atrial side of the mitral valve encroaching on the orifice of the mitral valve. It may adhere to the leaflets of the valve and restrict their movements. Although a supramitral ring may be rarely nonobstructive, it often results in mitral valve inflow obstruction.

  6. LPG based all plastic pressure sensor

    DEFF Research Database (Denmark)

    Bundalo, Ivan-Lazar; Lwin, R.; Leon-Saval, S.

    2015-01-01

    A prototype all-plastic pressure sensor is presented and characterized for potential use as an endoscope. The sensor is based on Long Period Gratings (LPG) inscribed with a CO2 laser in 6-ring microstructured PMMA fiber. Through a latex coated, plastic 3D-printed transducer pod, external pressure...

  7. Determinantal rings

    CERN Document Server

    Bruns, Winfried

    1988-01-01

    Determinantal rings and varieties have been a central topic of commutative algebra and algebraic geometry. Their study has attracted many prominent researchers and has motivated the creation of theories which may now be considered part of general commutative ring theory. The book gives a first coherent treatment of the structure of determinantal rings. The main approach is via the theory of algebras with straightening law. This approach suggest (and is simplified by) the simultaneous treatment of the Schubert subvarieties of Grassmannian. Other methods have not been neglected, however. Principal radical systems are discussed in detail, and one section is devoted to each of invariant and representation theory. While the book is primarily a research monograph, it serves also as a reference source and the reader requires only the basics of commutative algebra together with some supplementary material found in the appendix. The text may be useful for seminars following a course in commutative ring theory since a ...

  8. Cave Rings

    Science.gov (United States)

    2010-10-13

    hypothesis, that cave rings are formed in the same manner as coffee rings[3], that is, due to the enhanced deposition at the edges of sessile drops ...ring’ is the deposit formed when a sessile drop of a solution containing dissolved particles, such as coffee or salt, dries. This was investigated by...who expanded on Deegan et al.[3] to find an exact form for the evaporation flux over a sessile drop . It turns out that solving 179 for the flux is

  9. Vascular rings.

    Science.gov (United States)

    Backer, Carl L; Mongé, Michael C; Popescu, Andrada R; Eltayeb, Osama M; Rastatter, Jeffrey C; Rigsby, Cynthia K

    2016-06-01

    The term vascular ring refers to congenital vascular anomalies of the aortic arch system that compress the esophagus and trachea, causing symptoms related to those two structures. The most common vascular rings are double aortic arch and right aortic arch with left ligamentum. Pulmonary artery sling is rare and these patients need to be carefully evaluated for frequently associated tracheal stenosis. Another cause of tracheal compression occurring only in infants is the innominate artery compression syndrome. In the current era, the diagnosis of a vascular ring is best established by CT imaging that can accurately delineate the anatomy of the vascular ring and associated tracheal pathology. For patients with a right aortic arch there recently has been an increased recognition of a structure called a Kommerell diverticulum which may require resection and transfer of the left subclavian artery to the left carotid artery. A very rare vascular ring is the circumflex aorta that is now treated with the aortic uncrossing operation. Patients with vascular rings should all have an echocardiogram because of the incidence of associated congenital heart disease. We also recommend bronchoscopy to assess for additional tracheal pathology and provide an assessment of the degree of tracheomalacia and bronchomalacia. The outcomes of surgical intervention are excellent and most patients have complete resolution of symptoms over a period of time. Copyright © 2016 Elsevier Inc. All rights reserved.

  10. Evaluating multicast resilience in carrier ethernet

    DEFF Research Database (Denmark)

    Ruepp, Sarah Renée; Wessing, Henrik; Zhang, Jiang;

    2010-01-01

    This paper gives an overview of the Carrier Ethernet technology with specific focus on resilience. In particular, we show how multicast traffic, which is essential for IPTV can be protected. We detail the ackground for resilience mechanisms and their control and e present Carrier Ethernet...... resilience methods for linear nd ring networks. By simulation we show that the vailability of a multicast connection can be significantly increased by applying protection methods....

  11. Evaluating multicast resilience in carrier ethernet

    DEFF Research Database (Denmark)

    Ruepp, Sarah Renée; Wessing, Henrik; Zhang, Jiang

    2010-01-01

    This paper gives an overview of the Carrier Ethernet technology with specific focus on resilience. In particular, we show how multicast traffic, which is essential for IPTV can be protected. We detail the ackground for resilience mechanisms and their control and e present Carrier Ethernet...... resilience methods for linear nd ring networks. By simulation we show that the vailability of a multicast connection can be significantly increased by applying protection methods....

  12. Topological rings

    CERN Document Server

    Warner, S

    1993-01-01

    This text brings the reader to the frontiers of current research in topological rings. The exercises illustrate many results and theorems while a comprehensive bibliography is also included. The book is aimed at those readers acquainted with some very basic point-set topology and algebra, as normally presented in semester courses at the beginning graduate level or even at the advanced undergraduate level. Familiarity with Hausdorff, metric, compact and locally compact spaces and basic properties of continuous functions, also with groups, rings, fields, vector spaces and modules, and with Zorn''s Lemma, is also expected.

  13. Hydrogen carriers

    Science.gov (United States)

    He, Teng; Pachfule, Pradip; Wu, Hui; Xu, Qiang; Chen, Ping

    2016-12-01

    Hydrogen has the potential to be a major energy vector in a renewable and sustainable future energy mix. The efficient production, storage and delivery of hydrogen are key technical issues that require improvement before its potential can be realized. In this Review, we focus on recent advances in materials development for on-board hydrogen storage. We highlight the strategic design and optimization of hydrides of light-weight elements (for example, boron, nitrogen and carbon) and physisorbents (for example, metal-organic and covalent organic frameworks). Furthermore, hydrogen carriers (for example, NH3, CH3OH-H2O and cycloalkanes) for large-scale distribution and for on-site hydrogen generation are discussed with an emphasis on dehydrogenation catalysts.

  14. Plastics Technology.

    Science.gov (United States)

    Barker, Tommy G.

    This curriculum guide is designed to assist junior high schools industrial arts teachers in planning new courses and revising existing courses in plastics technology. Addressed in the individual units of the guide are the following topics: introduction to production technology; history and development of plastics; safety; youth leadership,…

  15. 化学氧化-铁离子覆盖改性聚氨酯泡沫塑料填料的特性%Characteristics of polyurethane(PU) foam plastics bio-carrier modified by chemical oxidation-surface covering with iron ion

    Institute of Scientific and Technical Information of China (English)

    杜振峰; 王芬; 成国栋; 林梦炜; 季民

    2012-01-01

    A surface modification method,chemical oxidation-surface covering with iron ion,was used to modify the polyurethane(PU) foam plastics bio-carrier.And surface properties of the bio-carrier,speed of biofilm formation,quantity of biological film and performance of treating wastewater were investigated before and after modification.The results showed that the ratio of the hydrophobic C-C,C-H bond on the surface of the modified bio-carrier was reduced by 15.81%,and the ratio of the hydrophilic C-O bond on the surface of the modified bio-carrier has increased by 16.17%.The dynamic contact angle of water against the bio-carrier surface was decreased by 10.46°.The surface roughness and hydrophilicity of the bio-carrier were enhanced.Comparing modified bio-carrier with the original bio-carrier,the quantity of biofilm increased by 60%,and the average growth rate of biological film increased by 50%.But the TTC-DHA of modified bio-carrier hardly increased.At the stage of biofilm formation,the performance of COD and ammonia removal of the modified bio-carrier was better than the original bio-carrier.After completion of biofilm formation,the removal efficiency of COD was almost the same,but the removal efficiency of ammonia increased by 10%.%采用化学氧化-铁离子覆盖改性方法对普通聚氨酯泡沫塑料填料进行改性,研究改性前后填料的表面特性、挂膜速度、生物膜量以及废水处理等性能。结果表明,改性填料表面的疏水性基团C—C、C—H比例下降了15.81%,亲水性基团C—O比例增加了16.17%,填料表面与蒸馏水的动态接触角减少了10.46°,其表面粗糙度以及亲水性提高。与未改性填料相比,改性填料生物膜量提高60%,生物膜平均每天生长量提高50%,但其生物膜脱氢酶活性并未明显提高。挂膜初期改性填料的COD和氨氮去除效果明显占优,挂膜完成后,改性填料对氨氮去除率比未改性填料高10%。

  16. Ring interferometry

    CERN Document Server

    Malykin, Grigorii B; Zhurov, Alexei

    2013-01-01

    This monograph is devoted to the creation of a comprehensive formalism for quantitative description of polarized modes' linear interaction in modern single-mode optic fibers. The theory of random connections between polarized modes, developed in the monograph, allows calculations of the zero shift deviations for a fiber ring interferometer. The monograph addresses also the

  17. On SAP-rings

    OpenAIRE

    Zhixiang, Wu

    2006-01-01

    The rings whose simple right modules are absolutely pure are called right $SAP$-rings. We give a new characterization of right $SAP$ rings, right $V$ rings, and von Neumann regular rings. We also obtain a new decomposition theory of right selfinjective von Neumann regular rings. The relationships between $SAP$-rings, $V$-rings, and von Neumann regular rings are explored. Some recent results obtained by Faith are generalized and the results of Wu-Xia are strengthened.

  18. Plastic bronchitis

    National Research Council Canada - National Science Library

    Singhi, Anil Kumar; Vinoth, Bharathi; Kuruvilla, Sarah; Sivakumar, Kothandam

    2015-01-01

    Plastic bronchitis, a rare but serious clinical condition, commonly seen after Fontan surgeries in children, may be a manifestation of suboptimal adaptation to the cavopulmonary circulation with unfavorable hemodynamics...

  19. Plastic Fishes

    CERN Multimedia

    Trettnak, Wolfgang

    2015-01-01

    In terms of weight, the plastic pollution in the world’s oceans is estimated to be around 300,000 tonnes. This plastic comes from both land-based and ocean-based sources. A lecture at CERN by chemist Wolfgang Trettnak addressed this issue and highlighted the role of art in raising people’s awareness. The slideshow below gives you a taste of the artworks by Wolfgang Trettnak and Margarita Cimadevila.

  20. Plastic Bridge

    Institute of Scientific and Technical Information of China (English)

    履之

    1994-01-01

    Already ubiquitous in homes and cars, plastic is now appearing inbridges. An academic-industrial consortium based at the University ofCalifornia in San Diego is launching a three-year research program aimed atdeveloping the world’s first plastic highway bridge, a 450-foot span madeentirely from glass-,carbon,and polymer-fiber-reinforced composite mate-rials, the stuff of military aircraft. It will cross Interstate 5 to connect thetwo sides of the school’s campus.

  1. Causes of ring-related leg injuries in birds - evidence and recommendations from four field studies.

    Directory of Open Access Journals (Sweden)

    Michael Griesser

    Full Text Available One of the main techniques for recognizing individuals in avian field research is marking birds with plastic and metal leg rings. However, in some species individuals may react negatively to rings, causing leg injuries and, in extreme cases, the loss of a foot or limb. Here, we report problems that arise from ringing and illustrate solutions based on field data from Brown Thornbills (Acanthiza pusilla (2 populations, Siberian Jays (Perisoreus infaustus and Purple-crowned Fairy-wrens (Malurus coronatus. We encountered three problems caused by plastic rings: inflammations triggered by material accumulating under the ring (Purple-crowned Fairy-wrens, contact inflammations as a consequence of plastic rings touching the foot or tibio-tarsal joint (Brown Thornbills, and toes or the foot getting trapped in partly unwrapped flat-band colour rings (Siberian Jays. Metal rings caused two problems: the edges of aluminium rings bent inwards if mounted on top of each other (Brown Thornbills, and too small a ring size led to inflammation (Purple-crowned Fairy-wrens. We overcame these problems by changing the ringing technique (using different ring types or larger rings, or using different adhesive. Additionally, we developed and tested a novel, simple technique of gluing plastic rings onto metal rings in Brown Thornbills. A review of studies reporting ring injuries (N = 23 showed that small birds (35 g tend to get rings stuck over their feet. We give methodological advice on how these problems can be avoided, and suggest a ringing hazard index to compare the impact of ringing in terms of injury on different bird species. Finally, to facilitate improvements in ringing techniques, we encourage online deposition of information regarding ringing injuries of birds at a website hosted by the European Union for Bird Ringing (EURING.

  2. 玻璃钢锚环承载性能的有限元分析%Finite Element Analysis of Bearing Capacity of Glass Fiber Reinforced Plastics Anchor Ring

    Institute of Scientific and Technical Information of China (English)

    刘建月; 崔小朝; 刘伟婧; 郑亚东

    2016-01-01

    通过 ABAQUS 有限元分析软件建立了连续玻璃纤维缠绕的聚酯树脂基玻璃钢锚环的有限元计算模型,对玻璃钢锚环与金属夹片、钢绞线配合使用的支护系统进行了加载分析。通过改变玻璃钢锚环的半锥角,研究了玻璃钢锚环与夹片的锥角搭配对锚具承载性能的影响。计算分析表明,在300 kN载荷作用下,计算模型中锚环纤维方向承载性能良好;轴对称面内最大主应力集中在锚环与夹片接触面附近,此处小范围基体开裂对锚环承载性能影响不大;锚环对称面内剪应力大面积超出基体强度极限,是影响锚环承载性能的主要因素。当夹片半锥角为7°时,玻璃钢锚环半锥角为6.3°~6.5°能改善锚环的应力分布状态,提高锚具的承载能力。%This paper established a finite element calculation model of continuous glass fiber winding and polyester resin GFRP anchor ring with ABAQUS,which conducted a loading analysis on the supporting system consisting of GFRP anchor ring,metal clip and steel strand.A research was made on the influence on the loading capacity of an-chor ring by changing the match of taper angles of GFRP anchor ring and clip.According to the calculation analy-sis,the anchor ring of the calculation model has a good bearing capacity in fiber direction under the load of 300 kN;in the symmetrical plane,the maximum principal stress is concentrated nearby the contact face between anchor ring and clip,and the crack of resin in small scale has small influence on the anchor ring bearing capacity;in sym-metrical plane,a large area of shearing stress of anchor ring surpassing resin ultimate stress is the main factor which can influence the loading capacity of anchor ring.When the half taper angle of clip is 7°and that of GFRP anchor ring is 6.3°~6.5°,the stress distribution and loading capacity of anchor ring can be well improved.

  3. GREEN PLASTIC: A NEW PLASTIC FOR PACKAGING

    OpenAIRE

    Mr. Pankaj Kumar*, Sonia

    2016-01-01

    This paper gives a brief idea about a new type of plastic called as bio-plastic or green plastic. Plastic is used as a packaging material for various products, but this plastic is made up of non renewable raw materials. There are various disadvantages of using conventional plastic like littering, CO2 production, non-degradable in nature etc. To overcome these problems a new type of plastic is discovered called bio-plastic or green plastic. Bio-plastic is made from renewable resources and also...

  4. Chemistry of HIV-1 virucidal Pt complexes having neglected bidentate sp2 N-donor carrier ligands with linked triazine and pyridine rings. synthesis, NMR spectral features, structure, and reaction with guanosine.

    Science.gov (United States)

    Maheshwari, Vidhi; Bhattacharyya, Debadeep; Fronczek, Frank R; Marzilli, Patricia A; Marzilli, Luigi G

    2006-09-04

    Complexes of the types LPtCl2 and [L2Pt]X2 [L = substituted 3-(pyridin-2'-yl)-1,2,4-triazine] were synthesized and characterized by NMR spectroscopy and, for the first time, by X-ray crystallography in an effort to determine the coordination properties of this novel class of inorganic medicinal agents possessing HIV-1 virucidal activity. The agents containing either one or two sp2 N-donor bidentate ligands are referred to as ptt (platinum triazine) agents. The X-ray structures of three LPtCl2 compounds revealed the expected pseudo-square-planar geometry. The X-ray structure of [(pyPh2t)2Pt](BF4)2 [pyPh2t = 3-(pyridin-2'-yl)-5,6-diphenyl-1,2,4-triazine] has the expected trans relationship of the unsymmetrical L and is essentially planar, an unusual property for a Pt(II) complex with two bidentate sp2 N donors. HIV-1 is an RNA virus; the guanosine ribonucleoside (Guo) binds (MepyMe2t)PtCl2 at both (inequivalent) available coordination sites to form [(MepyMe2t)Pt(Guo)2]2+ [MepyMe2t = 3-(4'-methylpyridin-2'-yl)-5,6-dimethyl-1,2,4-triazine]. This adduct has four nearly equally intense Guo H8 signals attributed to two pairs of head-to-tail (HT) and head-to-head (HH) conformers, which interchange rapidly within each pair. However, equilibration between pairs requires rotation of the Guo cis to the MepyMe2t pyridyl ring, and the H6' proton on this ring projects toward the Guo and hinders Guo rotation about the Pt-N7 bond. Thus, the HT/HH pairs do not interchange; such behavior is rare. Guo did not add to [(MepyMe2t)2Pt]2+, a result suggesting the possibility that the virucidal activity of LPtCl2 and [L2Pt]2+ ptt agents arises respectively from covalent and noncovalent (possibly intercalative interactions favored by [L2Pt]2+ planarity) binding to biomolecular targets.

  5. Deformation mechanism of cold ring rolling in view of texture evolution predicted by a newly proposed polycrystal plasticity model%基于新晶体塑性模型预测织构演化的环件冷轧变形机制

    Institute of Scientific and Technical Information of China (English)

    李宏伟; 冯璐; 杨合

    2013-01-01

    An explicit polycrystal plasticity model was proposed to investigate the deformation mechanism of cold ring rolling in view of texture evolution. The model was created by deducing a set of linear incremental controlling equations within the framework of crystal plasticity theory. It was directly solved by a linear algorithm within a two-level procedure so that its efficiency and stability were guaranteed. A subroutine VUMAT for ABAQUS/Explicit was developed to combine this model with the 3D FE model of cold ring rolling. Results indicate that the model is reliable in predictions of stress-strain response and texture evolution in the dynamic complicated forming process; the shear strain in RD of the ring is the critical deformation mode according to the sharp Goss component ({110}〈100〉) of deformed ring; texture and crystallographic structure of the ring blank do not affect texture type of the deformed ring;texture evolves rapidly at the later stage of rolling, which results in a dramatically increasing deformation of the ring.%提出一种新的多晶体塑性模型以从织构演化角度研究环件冷轧过程的变形机制。该模型是在晶体塑性理论框架内通过推导一套线性增量控制方程建立的。该模型可以用线性求解方法直接求解,并采用一个两步法的求解过程,确保模型计算的效率和稳定性。基于ABAQUS/Explicit平台开发了用户材料子程序VUMAT,以实现该模型与环件冷轧三维有限元模型的结合。结果表明,该模型在预测动态复杂成形过程中的应力应变响应和织构演化方面都是可靠的;从轧制环件中很强的Goss织构{110}〈100〉看出,环件轧向的剪切变形是环件冷轧过程中的主要变形;环坯的织构和晶体结构对轧制环件中的织构类型的影响不大;在冷轧的后期环件织构演化迅速,这导致了这一时期环件的快速长大。

  6. Origami rings

    CERN Document Server

    Buhler, Joe; de Launey, Warwick; Graham, Ron

    2010-01-01

    Motivated by a question in origami, we consider sets of points in the complex plane constructed in the following way. Let $L_\\alpha(p)$ be the line in the complex plane through $p$ with angle $\\alpha$ (with respect to the real axis). Given a fixed collection $U$ of angles, let $\\RU$ be the points that can be obtained by starting with $0$ and $1$, and then recursively adding intersection points of the form $L_\\alpha(p) \\cap L_\\beta(q)$, where $p, q$ have been constructed already, and $\\alpha, \\beta$ are distinct angles in $U$. Our main result is that if $U$ is a group with at least three elements, then $\\RU$ is a subring of the complex plane, i.e., it is closed under complex addition and multiplication. This enables us to answer a specific question about origami folds: if $n \\ge 3$ and the allowable angles are the $n$ equally spaced angles $k\\pi/n$, $0 \\le k < n$, then $\\RU$ is the ring $\\Z[\\zeta_n]$ if $n$ is prime, and the ring $\\Z[1/n,\\zeta_{n}]$ if $n$ is not prime, where $\\zeta_n := \\exp(2\\pi i/n)$ is ...

  7. Plastic Bronchitis.

    Science.gov (United States)

    Rubin, Bruce K

    2016-09-01

    Plastic bronchitis is an uncommon and probably underrecognized disorder, diagnosed by the expectoration or bronchoscopic removal of firm, cohesive, branching casts. It should not be confused with purulent mucous plugging of the airway as seen in patients with cystic fibrosis or bronchiectasis. Few medications have been shown to be effective and some are now recognized as potentially harmful. Current research directions in plastic bronchitis research include understanding the genetics of lymphatic development and maldevelopment, determining how abnormal lymphatic malformations contribute to cast formation, and developing new treatments. Copyright © 2016 Elsevier Inc. All rights reserved.

  8. Role of Friction in Cold Ring Rolling

    Institute of Scientific and Technical Information of China (English)

    He YANG; Lianggang GUO; Mei ZHAN

    2005-01-01

    Cold ring rolling is an advanced but complex metal forming process under coupled effects with multi-factors, such as geometry sizes of rolls and ring blank, material, forming process parameters and friction, etc. Among these factors,friction between rolls and ring blank plays animportant role in keeping the stable forming of cold ring rolling. An analytical method was firstly presented for proximately determining the critical friction coefficient of stable forming and then a method was proposed to determine thecritical friction coefficient by combining analytical method with numerical simulation. And the influence of friction coefficient on the quality of end-plane and side spread of ring,rolling force, rolling moment and metal flow characteristic in the cold ring rolling process have been explored using the three dimensional (3D) numerical simulation based on the elastic-plastic dynamic finite element method (FEM)under the ABAQUS software environment, and the results show that increasing the friction on the contact surfaces between rolls and ring blank is useful not only for improving the stability of cold ring rolling but also for improving the geometry and dimension precision of deformed ring.

  9. Mixed plastics recycling technology

    CERN Document Server

    Hegberg, Bruce

    1995-01-01

    Presents an overview of mixed plastics recycling technology. In addition, it characterizes mixed plastics wastes and describes collection methods, costs, and markets for reprocessed plastics products.

  10. Plastic fish

    CERN Multimedia

    Antonella Del Rosso

    2015-01-01

    In terms of weight, the plastic pollution in the world’s oceans is estimated to be around 300,000 tonnes. This plastic comes from both land-based and ocean-based sources. A lecture at CERN by chemist Wolfgang Trettnak addressed this issue and highlighted the role of art in raising people’s awareness.   Artwork by Wolfgang Trettnak. Packaging materials, consumer goods (shoes, kids’ toys, etc.), leftovers from fishing and aquaculture activities… our oceans and beaches are full of plastic litter. Most of the debris from beaches is plastic bottles. “PET bottles have high durability and stability,” explains Wolfgang Trettnak, a chemist by education and artist from Austria, who gave a lecture on this topic organised by the Staff Association at CERN on 26 May. “PET degrades very slowly and the estimated lifetime of a bottle is 450 years.” In addition to the beach litter accumulated from human use, rivers bring several ki...

  11. Plastic zonnecellen

    NARCIS (Netherlands)

    Roggen, Marjolein

    1998-01-01

    De zonnecel van de toekomst is in de maak. Onderzoekers van uiteenlopend pluimage werken eendrachtig aan een plastic zonnecel. De basis is technisch gelegd met een optimale, door invallend licht veroorzaakte, vorming van ladingdragers binnen een composiet van polymeren en buckyballs. Nu is het zaak

  12. Plastic Surgery Statistics

    Science.gov (United States)

    ... PSN PSEN GRAFT Contact Us News Plastic Surgery Statistics Plastic surgery procedural statistics from the American Society of Plastic Surgeons. Statistics by Year Print 2016 Plastic Surgery Statistics 2015 ...

  13. Plastic bronchitis

    Directory of Open Access Journals (Sweden)

    Anil Kumar Singhi

    2015-01-01

    Full Text Available Plastic bronchitis, a rare but serious clinical condition, commonly seen after Fontan surgeries in children, may be a manifestation of suboptimal adaptation to the cavopulmonary circulation with unfavorable hemodynamics. They are ominous with poor prognosis. Sometimes, infection or airway reactivity may provoke cast bronchitis as a two-step insult on a vulnerable vascular bed. In such instances, aggressive management leads to longer survival. This report of cast bronchitis discusses its current understanding.

  14. Prime rings with PI rings of constants

    CERN Document Server

    Kharchenko, V K; Rodríguez-Romo, S

    1996-01-01

    It is shown that if the ring of constants of a restricted differential Lie algebra with a quasi-Frobenius inner part satisfies a polynomial identity (PI) then the original prime ring has a generalized polynomial identitiy (GPI). If additionally the ring of constants is semiprime then the original ring is PI. The case of a non-quasi-Frobenius inner part is also considered.

  15. Accuracy of an electronic apex locator in the retreatment of teeth obturated with plastic or cross-linked gutta-percha carrier-based materials: an ex vivo study.

    Science.gov (United States)

    Mancini, Manuele; Palopoli, Pietro; Iorio, Lorenzo; Conte, Gabriele; Cianconi, Luigi

    2014-12-01

    This ex vivo study evaluated the accuracy of the Root ZX electronic apex locator (EAL) (J Morita Corp, Kyoto, Japan) in determining the working length during retreatment of canals sealed with 2 different carrier-based obturating materials (ProTaper Obturator [Dentsply Maillefer, Ballaigues, Switzerland] and GuttaCore [Dentsply Maillefer]) and also evaluated whether they influenced its accuracy differently. Fifty extracted single-rooted human teeth with sound apices were selected for the study. We measured canals with the direct visual technique using a #10 K-file and shaped them with ProTaper Universal instruments (Dentsply Maillefer) up to this predetermined length. After instrumentation, we determined the canal length again using the visual technique (direct length [DL]). This value was considered the "reference point." Specimens were then placed in a tooth holder (Pro-Train; Simit Dental, Mantova, Italy), and the canal length was electronically measured (electronic length 1 [EL1]). Specimens were then obturated with ProTaper Obturators (group 1, n = 25) and GuttaCore (group 2, n = 25). Seven days later, a new electronic length was determined (electronic length 2 [EL2]) during retreatment procedures in the presence of the obturating material. EL1 and EL2 values were compared with DL using the Bland and Altman method. The different influences of the tested materials on the accuracy of the EAL were calculated with repeated measures analysis of variance. Both EL1 and EL2 values provided a statistically significant overestimation of the actual canal length (DL [P materials did not influence the accuracy of the EAL differently (P = .486). The measurements obtained with the EAL tested during orthograde retreatments can lead clinicians to overinstrumentation and consequent overfilling of the endodontic space. Copyright © 2014 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

  16. Radical theory of rings

    CERN Document Server

    Gardner, JW

    2003-01-01

    Radical Theory of Rings distills the most noteworthy present-day theoretical topics, gives a unified account of the classical structure theorems for rings, and deepens understanding of key aspects of ring theory via ring and radical constructions. Assimilating radical theory's evolution in the decades since the last major work on rings and radicals was published, the authors deal with some distinctive features of the radical theory of nonassociative rings, associative rings with involution, and near-rings. Written in clear algebraic terms by globally acknowledged authorities, the presentation

  17. Thermo-mechanical coupled analysis of hot ring rolling process

    Institute of Scientific and Technical Information of China (English)

    SUN Zhi-chao; YANG He; OU Xin-zhe

    2008-01-01

    A 3D rigid-plastic and coupled thermo-mechanical FE model for hot ring rolling(HRR) was developed based on DEFORM 3D software, then coupled heat transferring, material flow and temperature distribution of the ring in HRR were simulated and the effects of process parameters on them were analyzed. The results show that the deformation nonuniformity of ring blank increases with the increase of the rotational speed of driver roll and friction factor or the decrease of the feed rate of idle roll and initial temperature of ring blank. The temperature nonuniformity of ring blank decreases with the increase of the feed rate of idle roll or the decrease of initial temperature of ring blank and friction factor. There is an optimum rotational speed of driver roll under which the temperature distribution of ring blank is the most uniform. The results obtained can provide a guide for forming parameters optimization and quality control.

  18. Stirling engine piston ring

    Science.gov (United States)

    Howarth, Roy B.

    1983-01-01

    A piston ring design for a Stirling engine wherein the contact pressure between the piston and the cylinder is maintained at a uniform level, independent of engine conditions through a balancing of the pressure exerted upon the ring's surface and thereby allowing the contact pressure on the ring to be predetermined through the use of a preloaded expander ring.

  19. Birth Control Ring

    Science.gov (United States)

    ... Loss Surgery? A Week of Healthy Breakfasts Shyness Birth Control Ring KidsHealth > For Teens > Birth Control Ring A A A What's in this article? ... español Anillo vaginal anticonceptivo What Is It? The birth control ring is a soft, flexible, doughnut-shaped ring ...

  20. Actin Rings of Power.

    Science.gov (United States)

    Schwayer, Cornelia; Sikora, Mateusz; Slováková, Jana; Kardos, Roland; Heisenberg, Carl-Philipp

    2016-06-20

    Circular or ring-like actin structures play important roles in various developmental and physiological processes. Commonly, these rings are composed of actin filaments and myosin motors (actomyosin) that, upon activation, trigger ring constriction. Actomyosin ring constriction, in turn, has been implicated in key cellular processes ranging from cytokinesis to wound closure. Non-constricting actin ring-like structures also form at cell-cell contacts, where they exert a stabilizing function. Here, we review recent studies on the formation and function of actin ring-like structures in various morphogenetic processes, shedding light on how those different rings have been adapted to fulfill their specific roles.

  1. Alternative loop rings

    CERN Document Server

    Goodaire, EG; Polcino Milies, C

    1996-01-01

    For the past ten years, alternative loop rings have intrigued mathematicians from a wide cross-section of modern algebra. As a consequence, the theory of alternative loop rings has grown tremendously. One of the main developments is the complete characterization of loops which have an alternative but not associative, loop ring. Furthermore, there is a very close relationship between the algebraic structures of loop rings and of group rings over 2-groups. Another major topic of research is the study of the unit loop of the integral loop ring. Here the interaction between loop rings and group ri

  2. Research on the expanding deformation of ring radius in cold profiled ring rolling process

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    Cold profiled ring rolling is an advanced local plastic deformation technology widely used to precisely manufacture various complex seamless ring parts.It plays an important role in many industrial fields such as aeronautics,astronautics,automobile,bearings,etc.In the cold ring rolling process,the ring radius expands gradually with the increase of the feeding amount(i.e.rolling reduction),and the expanding deformation of the ring radius is closely related to the rolling reduction.It is very important to investigate the expanding deformation of ring radius for the precise control of ring dimensions and the design of feeding movement.In this paper,the relation between the expanding deformation of the ring radius and the rolling reduction in the stepped ring rolling process,a typical profiled ring rolling process,is analyzed by using analytical method.The results show that the growth amount of the filling depth of groove can’t exceed the rolling reduction,that in the inner stepped ring rolling process,the curves of the outer radius and big inner radius with the rolling reduction are monotonous,ascending and concave,i.e.,the outer radius and big inner radius expand faster and faster with the increase of the rolling reduction,and that in the outer stepped ring rolling process,the curves of the inner radius and small outer radius with the rolling reduction are also monotonous,ascending and concave,i.e.,the inner radius and small outer radius expand faster and faster with the increase of the roll reduction.

  3. The effects of forming parameters on conical ring rolling process.

    Science.gov (United States)

    Meng, Wen; Zhao, Guoqun; Guan, Yanjin

    2014-01-01

    The plastic penetration condition and biting-in condition of a radial conical ring rolling process with a closed die structure on the top and bottom of driven roll, simplified as RCRRCDS, were established. The reasonable value range of mandrel feed rate in rolling process was deduced. A coupled thermomechanical 3D FE model of RCRRCDS process was established. The changing laws of equivalent plastic strain (PEEQ) and temperature distributions with rolling time were investigated. The effects of ring's outer radius growth rate and rolls sizes on the uniformities of PEEQ and temperature distributions, average rolling force, and average rolling moment were studied. The results indicate that the PEEQ at the inner layer and outer layer of rolled ring are larger than that at the middle layer of ring; the temperatures at the "obtuse angle zone" of ring's cross-section are higher than those at "acute angle zone"; the temperature at the central part of ring is higher than that at the middle part of ring's outer surfaces. As the ring's outer radius growth rate increases at its reasonable value ranges, the uniformities of PEEQ and temperature distributions increase. Finally, the optimal values of the ring's outer radius growth rate and rolls sizes were obtained.

  4. Overcoming maladaptive plasticity through plastic compensation

    Directory of Open Access Journals (Sweden)

    Matthew R.J. MORRIS, Sean M. ROGERS

    2013-08-01

    Full Text Available Most species evolve within fluctuating environments, and have developed adaptations to meet the challenges posed by environmental heterogeneity. One such adaptation is phenotypic plasticity, or the ability of a single genotype to produce multiple environmentally-induced phenotypes. Yet, not all plasticity is adaptive. Despite the renewed interest in adaptive phenotypic plasticity and its consequences for evolution, much less is known about maladaptive plasticity. However, maladaptive plasticity is likely an important driver of phenotypic similarity among populations living in different environments. This paper traces four strategies for overcoming maladaptive plasticity that result in phenotypic similarity, two of which involve genetic changes (standing genetic variation, genetic compensation and two of which do not (standing epigenetic variation, plastic compensation. Plastic compensation is defined as adaptive plasticity overcoming maladaptive plasticity. In particular, plastic compensation may increase the likelihood of genetic compensation by facilitating population persistence. We provide key terms to disentangle these aspects of phenotypic plasticity and introduce examples to reinforce the potential importance of plastic compensation for understanding evolutionary change [Current Zoology 59 (4: 526–536, 2013].

  5. Overcoming maladaptive plasticity through plastic compensation

    Institute of Scientific and Technical Information of China (English)

    Matthew R.J.MORRIS; Sean M.ROGERS

    2013-01-01

    Most species evolve within fluctuating environments,and have developed adaptations to meet the challenges posed by environmental heterogeneity.One such adaptation is phenotypic plasticity,or the ability of a single genotype to produce multiple environmentally-induced phenotypes.Yet,not all plasticity is adaptive.Despite the renewed interest in adaptive phenotypic plasticity and its consequences for evolution,much less is known about maladaptive plasticity.However,maladaptive plasticity is likely an important driver of phenotypic similarity among populations living in different environments.This paper traces four strategies for overcoming maladaptive plasticity that result in phenotypic similarity,two of which involve genetic changes (standing genetic variation,genetic compensation) and two of which do not (standing epigenetic variation,plastic compensation).Plastic compensation is defined as adaptive plasticity overcoming maladaptive plasticity.In particular,plastic compensation may increase the likelihood of genetic compensation by facilitating population persistence.We provide key terms to disentangle these aspects of phenotypic plasticity and introduce examples to reinforce the potential importance of plastic compensation for understanding evolutionary change.

  6. Reduction of the 1/f Noise Induced Phase Noise in a CMOS Ring Oscillator by Increasing the Amplitude of Oscillation

    NARCIS (Netherlands)

    Gierkink, S.L.J.; Wel, van der A.P.; Hoogzaad, G.; Klumperink, E.A.M.; Tuijl, van A.J.M.

    1998-01-01

    Spectrum measurement results of a CMOS ring oscillator are presented that show a 10 dB decrease in 1/f noise induced phase noise at a 2 dB increase in carrier power. Simple ring oscillator theory predicts that the 1/f noise induced phase noise is independent of carrier power. It is shown that an inc

  7. On JB-Rings

    Institute of Scientific and Technical Information of China (English)

    Huanyin CHEN

    2007-01-01

    A ring R is a QB-ring provided that aR + bR = R with a, b ∈ R implies that there exists a y ∈ R such that a+by ∈ R-1q. It is said that a ring R is a JB-ring provided that R/J(R) is a QB-ring, where J(R) is the Jacobson radical of R. In this paper, various necessary and sufficient conditions, under which a ring is a JB-ring, are established. It is proved that JB-rings can be characterized by pseudo-similarity. Furthermore, the author proves that R is a J B-ring iff so is R/J(R)2.

  8. Recycling of Plastic

    DEFF Research Database (Denmark)

    Christensen, Thomas Højlund; Fruergaard, Thilde

    2011-01-01

    Plastic is produced from fossil oil. Plastic is used for many different products. Some plastic products like, for example, wrapping foil, bags and disposable containers for food and beverage have very short lifetimes and thus constitute a major fraction of most waste. Other plastic products like......, good strength and long durability. Recycling of plastic waste from production is well-established, while recycling of postconsumer plastic waste still is in its infancy. This chapter describes briefly how plastic is produced and how waste plastic is recycled in the industry. Quality requirements...

  9. On semi ring bornologies

    Science.gov (United States)

    Imran, A. N.; Rakhimov, I. S.; Husain, Sh. K. Said

    2016-06-01

    Our main focus in this work is to introduce new structure bornological semi rings. This generalizes the theory of algebraic semi rings from the algebraic setting to the framework of bornological sets. We give basic properties for this new structure. As well as, We study the fundamental construction of bornological semi ring as product, inductive limits and projective limits and their extensions on bornological semi ring. Additionally, we introduce the category of bornological semi rings and study product and pullback (fiber product) in the category of bornological semi rings.

  10. Optical injection in semiconductor ring lasers

    CERN Document Server

    Coomans, W; Van der Sande, G; Gelens, L; Danckaert, J; 10.1103/PhysRevA.81.033802

    2011-01-01

    We theoretically investigate optical injection in semiconductor ring lasers and disclose several dynamical regimes. Through numerical simulations and bifurcation continuation, two separate parameter regions in which two different injection-locked solutions coexist are revealed, in addition to a region in which a frequency-locked limit cycle coexists with an injection-locked solution. Finally, an antiphase chaotic regime without the involvement of any carrier dynamics is revealed. Parallels are drawn with the onset of chaos in the periodically forced Duffing oscillator.

  11. Peptide-Carrier Conjugation

    DEFF Research Database (Denmark)

    Hansen, Paul Robert

    2015-01-01

    To produce antibodies against synthetic peptides it is necessary to couple them to a protein carrier. This chapter provides a nonspecialist overview of peptide-carrier conjugation. Furthermore, a protocol for coupling cysteine-containing peptides to bovine serum albumin is outlined....

  12. Groups, rings, modules

    CERN Document Server

    Auslander, Maurice

    2014-01-01

    This classic monograph is geared toward advanced undergraduates and graduate students. The treatment presupposes some familiarity with sets, groups, rings, and vector spaces. The four-part approach begins with examinations of sets and maps, monoids and groups, categories, and rings. The second part explores unique factorization domains, general module theory, semisimple rings and modules, and Artinian rings. Part three's topics include localization and tensor products, principal ideal domains, and applications of fundamental theorem. The fourth and final part covers algebraic field extensions

  13. LPG based all plastic pressure sensor

    DEFF Research Database (Denmark)

    Bundalo, Ivan-Lazar; Lwin, R.; Leon-Saval, S.

    2015-01-01

    A prototype all-plastic pressure sensor is presented and characterized for potential use as an endoscope. The sensor is based on Long Period Gratings (LPG) inscribed with a CO2 laser in 6-ring microstructured PMMA fiber. Through a latex coated, plastic 3D-printed transducer pod, external pressure...... is converted to longitudinal elongation of the pod and therefore of the fiber containing the LPG. The sensor has been characterised for pressures of up to 160 mBar in an in-house built pressure chamber. Furthermore, the influence of the fiber prestrain, fiber thickness and the effect of different glues...

  14. Birth Control Ring

    Science.gov (United States)

    ... Right Sport for You Healthy School Lunch Planner Birth Control Ring KidsHealth > For Teens > Birth Control Ring Print A A A What's in ... español Anillo vaginal anticonceptivo What Is It? The birth control ring is a soft, flexible, doughnut-shaped ...

  15. On Weakly Semicommutative Rings*

    Institute of Scientific and Technical Information of China (English)

    CHEN WEI-XING; CUI SHU-YING

    2011-01-01

    A ring R is said to be weakly scmicommutative if for any a, b ∈ R,ab = 0 implies aRb C_ Nil(R), where Nil(R) is the set of all nilpotcnt elements in R.In this note, we clarify the relationship between weakly semicommutative rings and NI-rings by proving that the notion of a weakly semicommutative ring is a proper generalization of NI-rings. We say that a ring R is weakly 2-primal if the set of nilpotent elements in R coincides with its Levitzki radical, and prove that if R is a weakly 2-primal ring which satisfies oα-condition for an endomorphism α of R (that is, ab = 0 (←→) aα(b) = 0 where a, b ∈ R) then the skew polynomial ring R[π; αα]is a weakly 2-primal ring, and that if R is a ring and I is an ideal of R such that I and R/I are both weakly semicommutative then R is weakly semicommutative.Those extend the main results of Liang et al. 2007 (Taiwanese J. Math., 11(5)(2007),1359-1368) considerably. Moreover, several new results about weakly semicommutative rings and NI-rings are included.

  16. Physics of quantum rings

    CERN Document Server

    Fomin, Vladimir M

    2013-01-01

    This book deals with a new class of materials, quantum rings. Innovative recent advances in experimental and theoretical physics of quantum rings are based on the most advanced state-of-the-art fabrication and characterization techniques as well as theoretical methods. The experimental efforts allow to obtain a new class of semiconductor quantum rings formed by capping self-organized quantum dots grown by molecular beam epitaxy. Novel optical and magnetic properties of quantum rings are associated with non-trivial topologies at the nanoscale. An adequate characterization of quantum rings is po

  17. Envelopes of Commutative Rings

    Institute of Scientific and Technical Information of China (English)

    Rafael PARRA; Manuel SAOR(I)N

    2012-01-01

    Given a significative class F of commutative rings,we study the precise conditions under which a commutative ring R has an F-envelope.A full answer is obtained when.F is the class of fields,semisimple commutative rings or integral domains.When F is the class of Noetherian rings,we give a full answer when the Krull dimension of R is zero and when the envelope is required to be epimorphic.The general problem is reduced to identifying the class of non-Noetherian rings having a monomorphic Noetherian envelope,which we conjecture is the empty class.

  18. RING PROXY SIGNATURES

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Proxy signatures have been used to enable the transfer of digital signing power within some context and ring signatures can be used to provide the anonymity of a signer. By combining the functionalities of proxy signatures and ring signatures, this paper introduces a new concept, named ring proxy signature, which is a proxy signature generated by an anonymous member from a set of potential signers. The paper also constructs the first concrete ring proxy signature scheme based on the provably secure Schnorr's signatures and two ID-based ring proxy signature schemes. The security analysis is provided as well.

  19. Arrangement for connecting a fiber-reinforced plastic pipe to a stainless steel flange

    Science.gov (United States)

    Allais, Arnaud; Hoffmann, Ernst

    2008-02-05

    Arrangement for connecting a fiber-reinforced plastic pipe (18) to a stainless steel flange (12, 16), in which the end of the fiber-reinforced plastic pipe (18) is accommodated in a ring-shaped groove (12a, 16a) in the flange (12, 16), the groove conforming to the dimensions of the fiber-reinforced plastic pipe (18), where the gap remaining between the end of the fiber-reinforced plastic pipe (18) and the ring-shaped groove (12a, 16a) is filled with a sealant (19).

  20. Saturn's largest ring.

    Science.gov (United States)

    Verbiscer, Anne J; Skrutskie, Michael F; Hamilton, Douglas P

    2009-10-22

    Most planetary rings in the Solar System lie within a few radii of their host body, because at these distances gravitational accelerations inhibit satellite formation. The best known exceptions are Jupiter's gossamer rings and Saturn's E ring, broad sheets of dust that extend outward until they fade from view at five to ten planetary radii. Source satellites continuously supply the dust, which is subsequently lost in collisions or by radial transport. Here we report that Saturn has an enormous ring associated with its outer moon Phoebe, extending from at least 128R(S) to 207R(S) (Saturn's radius R(S) is 60,330 km). The ring's vertical thickness of 40R(S) matches the range of vertical motion of Phoebe along its orbit. Dynamical considerations argue that these ring particles span the Saturnian system from the main rings to the edges of interplanetary space. The ring's normal optical depth of approximately 2 x 10(-8) is comparable to that of Jupiter's faintest gossamer ring, although its particle number density is several hundred times smaller. Repeated impacts on Phoebe, from both interplanetary and circumplanetary particle populations, probably keep the ring populated with material. Ring particles smaller than centimetres in size slowly migrate inward and many of them ultimately strike the dark leading face of Iapetus.

  1. The contraceptive vaginal ring.

    Science.gov (United States)

    Edwardson, Jill; Jamshidi, Roxanne

    2010-03-01

    The contraceptive vaginal ring offers effective contraception that is self-administered, requires less frequent dosing than many other forms of contraception, and provides low doses of hormones. NuvaRing (Organon, Oss, The Netherlands), the only contraceptive vaginal ring approved for use in the United States, contains etonogestrel and ethinyl estradiol. It is inserted into the vagina for 3 weeks, followed by a 1-week ring-free period, and works by inhibiting ovulation. Most women note a beneficial effect on bleeding profiles and are satisfied with NuvaRing. Commonly reported adverse events include vaginitis, leukorrhea, headaches, and device-related events such as discomfort. Serious adverse events are rare. In Chile and Peru, progesterone-only vaginal contraceptive rings are available for nursing women. Studies are ongoing examining new formulations of vaginal contraceptive rings.

  2. New Dust Belts of Uranus: One Ring, Two Ring, Red Ring, Blue Ring

    Energy Technology Data Exchange (ETDEWEB)

    de Pater, I; Hammel, H B; Gibbard, S G; Showalter, M R

    2006-02-02

    We compare near-infrared observations of the recently discovered outer rings of Uranus with HST results. We find that the inner ring, R/2003 U 2, is red, whereas the outer ring, R/2003 U 1, is very blue. Blue is an unusual color for rings; Saturn's enigmatic E ring is the only other known example. By analogy to the E ring, R/2003 U 1 is probably produced via impacts into the embedded moon Mab, which apparently orbits at a location where non-gravitational perturbations favor the survival and spreading of sub-micron sized dust. R/2003 U 2 more closely resembles Saturn's G ring.

  3. Composite cam carrier

    Energy Technology Data Exchange (ETDEWEB)

    Wicks, Christopher Donald; Madin, Mark Michael

    2017-03-14

    A cam carrier assembly includes a cylinder head having valves and a camshaft having lobes. A cam carrier has a first side coupled with the cylinder head engaging around the valves and a second side with bearing surfaces supporting the camshaft. A series of apertures extend between the first and second sides for the lobes to interface with the valves. The cam carrier is made of carbon fiber composite insulating the camshaft from the cylinder head and providing substantial weight reduction to an upper section of an associated engine.

  4. Asymmetric Carrier Random PWM

    DEFF Research Database (Denmark)

    Mathe, Laszlo; Lungeanu, Florin; Rasmussen, Peter Omand;

    2010-01-01

    This paper presents a new fixed carrier frequency random PWM method, where a new type of carrier wave is proposed for modulation. Based on the measurements, it is shown that the spread effect of the discrete components from the motor current spectra is very effective independent of the modulation...... index. The flat motor current spectrum generates an acoustical noise close to the white noise, which may improve the acoustical performance of the drive. The new carrier wave is easy to implement digitally, without employing any external circuits. The modulation method can be used in open, as well...

  5. Certain near-rings are rings, II

    Directory of Open Access Journals (Sweden)

    Howard E. Bell

    1986-01-01

    Full Text Available We investigate distributively-generated near-rings R which satisfy one of the following conditions: (i for each x,y∈R, there exist positive integers m, n for which xy=ymxn; (ii for each x,y∈R, there exists a positive integer n such that xy=(yxn. Under appropriate additional hypotheses, we prove that R must be a commutative ring.

  6. On Exchange QB∞-Rings

    Institute of Scientific and Technical Information of China (English)

    Huanyin Chen

    2007-01-01

    In this paper, we introduce a new class of rings, the QB∞-rings. We investigate necessary and sufficient conditions under which an exchange ring is a QB∞-ring. The modules over an exchange QB∞-ring are studied. Also, we prove that every regular square matrix over an exchange QB∞-ring admits a diagonal reduction by pseudo-invertible matrices.

  7. Neutrosophic LA-Semigroup Rings

    Directory of Open Access Journals (Sweden)

    Mumtaz Ali

    2015-01-01

    Full Text Available Neutrosophic LA-semigroup is a midway structure between a neutrosophic groupoid and a commutative neutrosophic semigroup. Rings are the old concept in algebraic structures. We combine the neutrosophic LA-semigroup and ring together to form the notion of neutrosophic LA-semigroup ring. Neutrosophic LAsemigroup ring is defined analogously to neutrosophic group ring and neutrosophic semigroup ring.

  8. Recycling of Plastic

    DEFF Research Database (Denmark)

    Christensen, Thomas Højlund; Fruergaard, Thilde

    2011-01-01

    Plastic is produced from fossil oil. Plastic is used for many different products. Some plastic products like, for example, wrapping foil, bags and disposable containers for food and beverage have very short lifetimes and thus constitute a major fraction of most waste. Other plastic products like......, for example, gutters, window frames, car parts and transportation boxes have long lifetimes and thus appear as waste only many years after they have been introduced on the market. Plastic is constantly being used for new products because of its attractive material properties: relatively cheap, easy to form......, good strength and long durability. Recycling of plastic waste from production is well-established, while recycling of postconsumer plastic waste still is in its infancy. This chapter describes briefly how plastic is produced and how waste plastic is recycled in the industry. Quality requirements...

  9. DETECTION OF COMPLEXES OLIGODEOXYNUCLEOTIDES WITH POLYMERIC CARRIERS

    Directory of Open Access Journals (Sweden)

    V. V. Vlizlo

    2013-10-01

    Full Text Available The new method for detection of cationic oligoelectrolytes conjugates with oligodeoxyonucleotides, based on free diffusion of these substances in 0.8% agarose gels is developed. It enables to simplify and reduce the cost of visual identification of the best carrier among various polymer compounds and to uncover the fact of complex formation between the interacting agents resulting in formation of a ring precipitation. The universality of the proposed methodological approach is confirmed by interaction of coligodeoxynucleotides with other cationic polymer of natural origin, namely chitosan. Comparative analysis of our approach applicationto turbidimetry data concerning coligodeoxynucleotides complexes and their electrophoresis showed some advantages, among them are the ability to screen simultaneously a large number of polymeric carriers and no need for using of more expensive equipment and materials. To conclude the complexing occurrence it is enough nanomol amounts of oligodeoxynucleotide.

  10. Dynamic explicit FE modeling of hot ring rolling process

    Institute of Scientific and Technical Information of China (English)

    WANG Min; YANG He; SUN Zhi-chao; GUO Liang-gang; OU Xin-zhe

    2006-01-01

    A new FE modeling method of hot ring rolling was presented by solving key technologies such as contact and heat boundary conditions, motion control over guide rolls, and mass scaling. The method has the following features: 1) the elastic-plastic dynamic explicit approach instead of the static implicit approach is adopted to solve the process so as to greatly improve computational efficiency without sacrificing computational accuracy; 2) the coupled thermal-mechanical effect is considered as opposed to the conventional isothermal assumption, which is more practical; 3) in contrast to the simplified 2D or local 3D ring model, the full 3D ring is modeled to simulate the process. Based on the FE modeling method, two cases of hot plain ring rolling are simulated in the FEA software ABAQUS/Explicit. The simulation results are compared with the experimental measurements and the good agreement between them is observed regarding the material flow and the temperature distribution of the ring.

  11. Gulf ring algae

    Science.gov (United States)

    Although they rank among the tiniest of the microspcopic phytoplankton, coccolithophore algae aid oceanographers studying the Gulf Stream rings and the ring boundaries. The algal group could help to identify more precisely the boundary of the warm rings of water that spin off from the Gulf Stream and become independent pools of warm water in the colder waters along the northeastern U.S. coast.Coccolithophore populations in the Gulf Stream rings intrigue oceanographers for two reasons: The phytoplankton are subjected to an environment that changes every few days, and population explosions within one coccolithophore species seem to be associated with changes in the characteristics of ocean water, said Pat Blackwelder, an associate professor at the Nova Oceanographic Center in Dania, Fla. She is one of many studying the physics, chemistry, and biology of warm core rings. A special oceanography session on these rings was held at the recent AGU Fall Meeting/ASLO Winter Meeting.

  12. Token Ring Project

    Directory of Open Access Journals (Sweden)

    Adela Ionescu

    2007-01-01

    Full Text Available Ring topology is a simple configuration used to connect processes that communicate among themselves. A number of network standards such as token ring, token bus, and FDDI are based on the ring connectivity. This article will develop an implementation of a ring of processes that communicate among themselves via pipe links. The processes are nodes in the ring. Each process reads from its standard input and writes in its standard output. N-1 process redirects the its standard output to a standard input of the process through a pipe. When the ring-structure is designed, the project can be extended to simulate networks or to implement algorithms for mutual exclusion

  13. 77 FR 54930 - Carlyle Plastics and Resins, Formerly Known as Fortis Plastics, A Subsidiary of Plastics...

    Science.gov (United States)

    2012-09-06

    ... Employment and Training Administration Carlyle Plastics and Resins, Formerly Known as Fortis Plastics, A... plastic parts. New information shows that Fortis Plastics is now called Carlyle Plastics and Resins. In... of Carlyle Plastics and Resins, formerly known as Fortis Plastics, a subsidiary of...

  14. 40 CFR 238.20 - Definitions.

    Science.gov (United States)

    2010-07-01

    ... Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) OCEAN DUMPING DEGRADABLE PLASTIC RING... means the percent increase in length of the plastic material caused by a tensile load. Percent... entities that produce ring carriers ready for use as beverage carriers. Ring carrier means any plastic ring...

  15. Photoinduced Transformation between Charge Carrier and Spin Carrier in Polymers

    Institute of Scientific and Technical Information of China (English)

    MEI Yuan; ZHAO Chang; SUN Xin

    2006-01-01

    By dynamical simulations, we show a transforming process between neutral soliton (spin carrier) and charged soliton (charge carrier) in polymers via photo-excitation, taking a polaron as the transitional bridge. It is photoinduced transformation between spin carrier and charge carrier. In this way, we demonstrate an access for polymers to be applied to spintronics.

  16. Carrier-less, anti-backlash planetary drive system

    Science.gov (United States)

    Vranish, John M. (Inventor)

    1995-01-01

    This invention relates to a carrier-less, anti-backlash planetary gear system that has an input sun gear, a force-balancing and planet-alignment 'speeder' gear above the sun gear, a split ring gear that has a fixed lower ring gear coaxial with the sun gear and a rotating upper ring gear also coaxial with the sun gear. A preload bolt is used for securing the split ring gears together. Within the split ring gear is an even number of planet gears between the split ring gear and the sun gear. Each planet gear consists of an upper planet gear, and lower planet gear with the upper and lower planet gears splined together and pushed apart by a spring which causes separation and relative twist between the upper and lower planet gears. The lower planet gear meshes with the input sun gear and the fixed ring gear while the upper planet gear is driven by the lower planet gear and meshes with the rotating ring gear.

  17. Dusty plasma (Yukawa) rings

    CERN Document Server

    Sheridan, T E

    2010-01-01

    One-dimensional and quasi-one-dimensional strongly-coupled dusty plasma rings have been created experimentally. Longitudinal (acoustic) and transverse (optical) dispersion relations for the 1-ring were measured and found to be in very good agreement with the theory for an unbounded straight chain of particles interacting through a Yukawa (i.e., screened Coulomb or Debye-H\\"uckel) potential. These rings provide a new system in which to study one-dimensional and quasi-one-dimensional physics.

  18. Token ring technology report

    CERN Document Server

    2013-01-01

    Please note this is a Short Discount publication. This report provides an overview of the IBM Token-Ring technology and products built by IBM and compatible vendors. It consists of two sections: 1. A summary of the design trade-offs for the IBM Token-Ring. 2. A summary of the products of the major token-ring compatible vendors broken down by adapters and components, wiring systems, testing, and new chip technology.

  19. From macro- to microplastics - Analysis of EU regulation along the life cycle of plastic bags

    DEFF Research Database (Denmark)

    Steensgaard, Ida M; Syberg, Kristian; Rist, Sinja

    2017-01-01

    exposure and hazards of macro- and microplastics. In this paper, we map European regulation taking outset in the life cycle perspective of plastic carrier bags: from plastic bag production to when it enters the environment. Relevant regulatory frameworks, directives and authorities along the life cycle...... are identified and their role in regulation of plastics is discussed. Most important regulations were identified as: the EU chemical Regulation, the Packaging and Packaging Waste Directive including the amending Directive regarding regulation of the consumption of lightweight plastic carrier bags, the Waste...... requirements as hazardous waste involving stricter requirements to labelling, recordkeeping, monitoring and control over the whole lifecycle. Finally, we recommend that more ambitious recycle and recovery targets are set across the EU. Regulation of the consumption of lightweight plastic carrier bags should...

  20. On -Coherent Endomorphism Rings

    Indian Academy of Sciences (India)

    Li-Xin Mao

    2008-11-01

    A ring is called right -coherent if every principal right ideal is finitely presented. Let $M_R$ be a right -module. We study the -coherence of the endomorphism ring of $M_R$. It is shown that is a right -coherent ring if and only if every endomorphism of $M_R$ has a pseudokernel in add $M_R; S$ is a left -coherent ring if and only if every endomorphism of $M_R$ has a pseudocokernel in add $M_R$. Some applications are given.

  1. Physics of quantum rings

    Energy Technology Data Exchange (ETDEWEB)

    Fomin, Vladimir M. (ed.) [Leibniz Institute for Solid State and Materials Research, Dresden (Germany)

    2014-07-01

    Presents the new class of materials of quantum rings. Provides an elemental basis for low-cost high-performance devices promising for electronics, optoelectronics, spintronics and quantum information processing. Explains the physical properties of quantum rings to cover a gap in scientific literature. Presents the application of most advanced nanoengineering and nanocharacterization techniques. This book deals with a new class of materials, quantum rings. Innovative recent advances in experimental and theoretical physics of quantum rings are based on the most advanced state-of-the-art fabrication and characterization techniques as well as theoretical methods. The experimental efforts allow to obtain a new class of semiconductor quantum rings formed by capping self-organized quantum dots grown by molecular beam epitaxy. Novel optical and magnetic properties of quantum rings are associated with non-trivial topologies at the nanoscale. An adequate characterization of quantum rings is possible on the basis of modern characterization methods of nanostructures, such as Scanning Tunneling Microscopy. A high level of complexity is demonstrated to be needed for a dedicated theoretical model to adequately represent the specific features of quantum rings. The findings presented in this book contribute to develop low-cost high-performance electronic, spintronic, optoelectronic and information processing devices based on quantum rings.

  2. Our plastic age

    National Research Council Canada - National Science Library

    Richard C. Thompson; Shanna H. Swan; Charles J. Moore; Frederick S. vom Saal

    2009-01-01

    Within the last few decades, plastics have revolutionized our daily lives. Globally we use in excess of 260 million tonnes of plastic per annum, accounting for approximately 8 per cent of world oil production...

  3. Weinig plastic in vissenmaag

    NARCIS (Netherlands)

    Foekema, E.M.

    2012-01-01

    Waar de magen van sommige zeevogels vol plastic zitten, lijken vissen in de Noordzee nauwelijks last te hebben van kunststofafval. Onderzoekers die plastic resten zochten in vissenmagen vonden ze in elk geval nauwelijks.

  4. Ear Plastic Surgery

    Science.gov (United States)

    ... ENTCareers Marketplace Find an ENT Doctor Near You Ear Plastic Surgery Ear Plastic Surgery Patient Health Information ... they may improve appearance and self-confidence. Can Ear Deformities Be Corrected? Formation of the ear during ...

  5. Biodegradability of Plastics

    OpenAIRE

    Yutaka Tokiwa; Calabia, Buenaventurada P.; Charles U. Ugwu; Seiichi Aiba

    2009-01-01

    Plastic is a broad name given to different polymers with high molecular weight, which can be degraded by various processes. However, considering their abundance in the environment and their specificity in attacking plastics, biodegradation of plastics by microorganisms and enzymes seems to be the most effective process. When plastics are used as substrates for microorganisms, evaluation of their biodegradability should not only be based on their chemical structure, but also on their physical ...

  6. The value of energy carriers

    NARCIS (Netherlands)

    Gool, W. van

    1987-01-01

    The value of energy carriers can be described thermodynamically by the amount of heat (enthalpy method) or work (exergy or availability method) that can be obtained from the carriers. Prices for energy carriers are used in economics to express their values. The prices for energy carriers are often r

  7. Chemical Recycle of Plastics

    Directory of Open Access Journals (Sweden)

    Sara Fatima

    2014-11-01

    Full Text Available Various chemical processes currently prevalent in the chemical industry for plastics recycling have been discussed. Possible future scenarios in chemical recycling have also been discussed. Also analyzed are the effects on the environment, the risks, costs and benefits of PVC recycling. Also listed are the various types of plastics and which plastics are safe to use and which not after rcycle

  8. Plastic value chains

    DEFF Research Database (Denmark)

    Baxter, John; Wahlstrom, Margareta; Zu Castell-Rüdenhausen, Malin

    2014-01-01

    Optimizing plastic value chains is regarded as an important measure in order to increase recycling of plastics in an efficient way. This can also lead to improved awareness of the hazardous substances contained in plastic waste, and how to avoid that these substances are recycled. As an example...

  9. Ring Around a Galaxy

    Science.gov (United States)

    1999-01-01

    Space Telescope Science Institute astronomers are giving the public chances to decide where to aim NASA's Hubble Space Telescope. Guided by 8,000 Internet voters, Hubble has already been used to take a close-up, multi-color picture of the most popular object from a list of candidates, the extraordinary 'polar-ring' galaxy NGC 4650A. Located about 130 million light-years away, NGC 4650A is one of only 100 known polar-ring galaxies. Their unusual disk-ring structure is not yet understood fully. One possibility is that polar rings are the remnants of colossal collisions between two galaxies sometime in the distant past, probably at least 1 billion years ago. What is left of one galaxy has become the rotating inner disk of old red stars in the center. Meanwhile, another smaller galaxy which ventured too close was probably severely damaged or destroyed. The bright bluish clumps, which are especially prominent in the outer parts of the ring, are regions containing luminous young stars, examples of stellar rebirth from the remnants of an ancient galactic disaster. The polar ring appears to be highly distorted. No regular spiral pattern stands out in the main part of the ring, and the presence of young stars below the main ring on one side and above on the other shows that the ring is warped and does not lie in one plane. Determining the typical ages of the stars in the polar ring is an initial goal of our Polar Ring Science Team that can provide a clue to the evolution of this unusual galaxy. The HST exposures were acquired by the Hubble Heritage Team, consisting of Keith Noll, Howard Bond, Carol Christian, Jayanne English, Lisa Frattare, Forrest Hamilton, Anne Kinney and Zolt Levay, and guest collaborators Jay Gallagher (University of Wisconsin-Madison), Lynn Matthews (National Radio Astronomy Observatory-Charlottesville), and Linda Sparke (University of Wisconsin-Madison).

  10. Carrier transport uphill. I. General

    DEFF Research Database (Denmark)

    Rosenberg, T; Wilbrandt, W

    1963-01-01

    A quantitative treatment of a carrier pump operating with two carrier forms C and Z is presented. Asymmetric metabolic reactions are assumed to transform Z into C on one and C into Z on the other side of the membrane, establishing a carrier cycle. The kinetical consequences of this mechanism...... concords with equilibrating carrier systems in all characteristic kinetical features is taken to indicate that the carrier mechanism contributes more to the characteristic transport features than the connection with metabolism....

  11. Neptune's ring system.

    Science.gov (United States)

    Porco, C. C.; Nicholson, P. D.; Cuzzi, J. N.; Lissauer, J. J.; Esposito, L. W.

    The authors review the current state of knowledge regarding the structure, particle properties, kinematics, dynamics, origin, and evolution of the Neptune rings derived from Earth-based and Voyager data. Neptune has a diverse system of five continuous rings - 2 broad (Galle and Lassell) and 3 narrow (Adams, Le Verrier, and Arago) - plus a narrow discontinuous ring sharing the orbit of one of its ring-region satellites, Galatea. The outermost Adams ring contains the only arcs observed so far in Voyager images. The five arcs vary in angular extent from ≡1° to ≡10°, and exhibit internal azimuthal structure with typical spatial scales of ≡0.5°. All five lie within ≡40° of longitude. Dust is present throughout the Neptune system and measureable quantities of it were detected over Neptune's north pole. The Adams ring (including the arcs) and the Le Verrier ring contain a significant fraction of dust. The Neptune ring particles are probably red, and may consist of ice "dirtied" with silicates and/or some carbon-bearing material. A kinematic model for the arcs derived from Voyager data, the arcs' physical characteristics, and their orbital geometry and phasing are all roughly in accord with single-satellite arc shepherding by Galatea, though the presence of small kilometer-sized bodies embedded either within the arcs or placed at their Lagrange points may explain some inconsistencies with this model.

  12. Algorithms for finite rings

    NARCIS (Netherlands)

    Ciocanea Teodorescu I.,

    2016-01-01

    In this thesis we are interested in describing algorithms that answer questions arising in ring and module theory. Our focus is on deterministic polynomial-time algorithms and rings and modules that are finite. The first main result of this thesis is a solution to the module isomorphism problem in

  13. Revocable Ring Signature

    Institute of Scientific and Technical Information of China (English)

    Dennis Y. W. Liu; Joseph K. Liu; Yi Mu; Willy Susilo; Duncan S. Wong

    2007-01-01

    Group signature allows the anonymity of a real signer in a group to be revoked by a trusted party called group manager. It also gives the group manager the absolute power of controlling the formation of the group. Ring signature, on the other hand, does not allow anyone to revoke the signer anonymity, while allowing the real signer to forma group (also known as a ring) arbitrarily without being controlled by any other party. In this paper, we propose a new variant for ring signature, called Revocable Ring Signature. The signature allows a real signer to form a ring arbitrarily while allowing a set of authorities to revoke the anonymity of the real signer. This new variant inherits the desirable properties from both group signature and ring signature in such a way that the real signer will be responsible for what it has signed as the anonymity is revocable by authorities while the real signer still has the freedom on ring formation. We provide a formal security model for revocable ring signature and propose an efficient construction which is proven secure under our security model.

  14. Illustration of Saturn's Rings

    Science.gov (United States)

    2001-01-01

    This illustration shows a close-up of Saturn's rings. These rings are thought to have formed from material that was unable to form into a Moon because of tidal forces from Saturn, or from a Moon that was broken up by Saturn's tidal forces.

  15. The Fermilab recycler ring

    Energy Technology Data Exchange (ETDEWEB)

    Martin Hu

    2001-07-24

    The Fermilab Recycler is a permanent magnet storage ring for the accumulation of antiprotons from the Antiproton Source, and the recovery and cooling of the antiprotons remaining at the end of a Tevatron store. It is an integral part of the Fermilab III luminosity upgrade. The following paper describes the design features, operational and commissioning status of the Recycler Ring.

  16. EBT ring physics

    Energy Technology Data Exchange (ETDEWEB)

    Uckan, N.A. (ed.)

    1980-04-01

    This workshop attempted to evaluate the status of the current experimental and theoretical understanding of hot electron ring properties. The dominant physical processes that influence ring formation, scaling, and their optimal behavior are also studied. Separate abstracts were prepared for each of the 27 included papers. (MOW)

  17. Smoke Ring Physics

    Science.gov (United States)

    Huggins, Elisha

    2011-01-01

    The behavior of smoke rings, tornados, and quantized vortex rings in superfluid helium has many features in common. These features can be described by the same mathematics we use when introducing Ampere's law in an introductory physics course. We discuss these common features. (Contains 7 figures.)

  18. Algorithms for finite rings

    NARCIS (Netherlands)

    Ciocanea Teodorescu I.,

    2016-01-01

    In this thesis we are interested in describing algorithms that answer questions arising in ring and module theory. Our focus is on deterministic polynomial-time algorithms and rings and modules that are finite. The first main result of this thesis is a solution to the module isomorphism problem in

  19. Planetary rings - Theory

    Science.gov (United States)

    Borderies, Nicole

    1989-01-01

    Theoretical models of planetary-ring dynamics are examined in a brief analytical review. The mathematical description of streamlines and streamline interactions is outlined; the redistribution of angular momentum due to collisions between particles is explained; and problems in the modeling of broad, narrow, and arc rings are discussed.

  20. Steroidal contraceptive vaginal rings.

    Science.gov (United States)

    Sarkar, N N

    2003-06-01

    The development of steroid-releasing vaginal rings over the past three decades is reviewed to illustrate the role of this device as an effective hormonal contraceptive for women. Vaginal rings are made of polysiloxane rubber or ethylene-vinyl-acetate copolymer with an outer diameter of 54-60 mm and a cross-sectional diameter of 4-9.5 mm and contain progestogen only or a combination of progestogen and oestrogen. The soft flexible combined ring is inserted in the vagina for three weeks and removed for seven days to allow withdrawal bleeding. Progesterone/progestogen-only rings are kept in for varying periods and replaced without a ring-free period. Rings are in various stages of research and development but a few, such as NuvaRing, have reached the market in some countries. Women find this method easy to use, effective, well tolerated and acceptable with no serious side-effects. Though the contraceptive efficacy of these vaginal rings is high, acceptability is yet to be established.

  1. Biodegradability of plastics.

    Science.gov (United States)

    Tokiwa, Yutaka; Calabia, Buenaventurada P; Ugwu, Charles U; Aiba, Seiichi

    2009-08-26

    Plastic is a broad name given to different polymers with high molecular weight, which can be degraded by various processes. However, considering their abundance in the environment and their specificity in attacking plastics, biodegradation of plastics by microorganisms and enzymes seems to be the most effective process. When plastics are used as substrates for microorganisms, evaluation of their biodegradability should not only be based on their chemical structure, but also on their physical properties (melting point, glass transition temperature, crystallinity, storage modulus etc.). In this review, microbial and enzymatic biodegradation of plastics and some factors that affect their biodegradability are discussed.

  2. Plastic value chains

    DEFF Research Database (Denmark)

    Baxter, John; Wahlstrom, Margareta; Zu Castell-Rüdenhausen, Malin

    2014-01-01

    Optimizing plastic value chains is regarded as an important measure in order to increase recycling of plastics in an efficient way. This can also lead to improved awareness of the hazardous substances contained in plastic waste, and how to avoid that these substances are recycled. As an example......, plastics from WEEE is chosen as a Nordic case study. The project aims to propose a number of improvements for this value chain together with representatives from Nordic stakeholders. Based on the experiences made, a guide for other plastic value chains shall be developed....

  3. Biodegradability of Plastics

    Directory of Open Access Journals (Sweden)

    Yutaka Tokiwa

    2009-08-01

    Full Text Available Plastic is a broad name given to different polymers with high molecular weight, which can be degraded by various processes. However, considering their abundance in the environment and their specificity in attacking plastics, biodegradation of plastics by microorganisms and enzymes seems to be the most effective process. When plastics are used as substrates for microorganisms, evaluation of their biodegradability should not only be based on their chemical structure, but also on their physical properties (melting point, glass transition temperature, crystallinity, storage modulus etc.. In this review, microbial and enzymatic biodegradation of plastics and some factors that affect their biodegradability are discussed.

  4. Journal of CHINA PLASTICS

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    Journal of CHINA PLASTICS was authorized and approved by The State Committee of Science and Technology of China and The Bureau of News Press of China, and published by The China Plastics Processing Industry Association,Beijing Technology and Business University and The Institute of Plastics Processing and Application of Light Industry, distributed worldwide. Since its birth in 1987, CHINA PLASTICS has become a leading magazine in plastics industry in China, a national Chinese core journal and journal of Chinese scientific and technological article statistics. It is covered by CA.

  5. Jupiter's Rings: Sharpest View

    Science.gov (United States)

    2007-01-01

    The New Horizons spacecraft took the best images of Jupiter's charcoal-black rings as it approached and then looked back at Jupiter. The top image was taken on approach, showing three well-defined lanes of gravel- to boulder-sized material composing the bulk of the rings, as well as lesser amounts of material between the rings. New Horizons snapped the lower image after it had passed Jupiter on February 28, 2007, and looked back in a direction toward the sun. The image is sharply focused, though it appears fuzzy due to the cloud of dust-sized particles enveloping the rings. The dust is brightly illuminated in the same way the dust on a dirty windshield lights up when you drive toward a 'low' sun. The narrow rings are confined in their orbits by small 'shepherding' moons.

  6. Challenges in plastics recycling

    DEFF Research Database (Denmark)

    Pivnenko, Kostyantyn; Jakobsen, L. G.; Eriksen, Marie Kampmann

    2015-01-01

    Recycling of waste plastics still remains a challenging area in the waste management sector. The current and potential goals proposed on EU or regional levels are difficult to achieve, and even to partially fullfil them the improvements in collection and sorting should be considerable. A study...... was undertaken to investigate the factors affecting quality in plastics recycling. The preliminary results showed factors primarily influencing quality of plastics recycling to be polymer cross contamination, presence of additives, non-polymer impurities, and polymer degradation. Deprivation of plastics quality......, with respect to recycling, has been shown to happen throughout the plastics value chain, but steps where improvements may happen have been preliminary identified. Example of Cr in plastic samples analysed showed potential spreading and accumulation of chemicals ending up in the waste plastics. In order...

  7. Glassy metallic plastics

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    This paper reports a class of bulk metallic glass including Ce-, LaCe-, CaLi-, Yb-, and Sr-based metallic glasses, which are regarded as glassy metallic plastics because they combine some unique properties of both plastics and metallic alloys. These glassy metallic plastics have very low glass transition temperature (Tg~25oC to 150oC) and low Young’s modulus (~20 GPa to 35 GPa). Similar to glassy plastics, these metallic plastics show excellent plastic-like deformability on macro-, micro- and even nano-scale in their supercooled liquid range and can be processed, such as elongated, compressed, bent, and imprinted at low temperatures, in hot water for instance. Under ambient conditions, they display such metallic properties as high thermal and electric conductivities and excellent mechanical properties and other unique properties. The metallic plastics have potential applications and are also a model system for studying issues in glass physics.

  8. The Enceladus Ring

    Science.gov (United States)

    2006-01-01

    [figure removed for brevity, see original site] The Enceladus Ring (labeled) This excellent view of the faint E ring -- a ring feature now known to be created by Enceladus -- also shows two of Saturn's small moons that orbit within the ring, among a field of stars in the background. The E ring extends from three to eight Saturn radii -- about 180,000 kilometers (118,000 miles) to 482,000 kilometers (300,000 miles). Its full extent is not visible in this view. Calypso (22 kilometers, or 14 miles across) and Helene (32 kilometers, or 20 miles across) orbit within the E ring's expanse. Helene skirts the outer parts of the E ring, but here it is projected in front of a region deeper within the ring. Calypso and Helene are trojan satellites, or moons that orbit 60 degrees in front or behind a larger moon. Calypso is a Tethys trojan and Helene is a trojan of Dione. An interesting feature of note in this image is the double-banded appearance of the E-ring, which is created because the ring is somewhat fainter in the ringplane than it is 500-1,000 kilometers (300-600 miles) above and below the ringplane. This appearance implies that the particles in this part of the ring have nonzero inclinations (a similar affect is seen in Jupiter's gossamer ring). An object with a nonzero inclination does not orbit exactly at Saturn's ringplane. Instead, its orbit takes it above and below the ringplane. Scientists are not entirely sure why the particles should have such inclinations, but they are fairly certain that the reason involves Enceladus. One possible explanation is that all the E ring particles come from the plume of icy material that is shooting due south out of the moon's pole. This means all of the particles are created with a certain velocity out of the ringplane, and then they orbit above and below that plane. Another possible explanation is that Enceladus produces particles with a range of speeds, but the moon gravitationally scatters any particles that lie very close to

  9. Intestinal solute carriers

    DEFF Research Database (Denmark)

    Steffansen, Bente; Nielsen, Carsten Uhd; Brodin, Birger

    2004-01-01

    A large amount of absorptive intestinal membrane transporters play an important part in absorption and distribution of several nutrients, drugs and prodrugs. The present paper gives a general overview on intestinal solute carriers as well as on trends and strategies for targeting drugs and/or pro...

  10. Autonomous component carrier selection

    DEFF Research Database (Denmark)

    Garcia, Luis Guilherme Uzeda; Pedersen, Klaus; Mogensen, Preben

    2009-01-01

    in local areas, basing our study case on LTE-Advanced. We present extensive network simulation results to demonstrate that a simple and robust interference management scheme, called autonomous component carrier selection allows each cell to select the most attractive frequency configuration; improving...

  11. Earth: A Ringed Planet?

    Science.gov (United States)

    Hancock, L. O.; Povenmire, H.

    2010-12-01

    Among the most beautiful findings of the Space Age have been the discoveries of planetary rings. Not only Saturn but also Jupiter, Uranus and Neptune have rings; Saturn’s ring system has structures newly discovered; even Saturn's moon Rhea itself has a ring. All these are apparently supplied by material from the planetary moons (Rhea's ring by Rhea itself). The question naturally arises, why should the Earth not have a ring, and on the other hand, if it does, why has it not been observed? No rings have yet been observed in the inner solar system, but after all, rings in the inner solar system might simply tend to be fainter and more transient than those of the outer solar system: the inner solar system is more affected by the solar wind, and the Sun’s perturbing gravitational influence is greater. J.A. O’Keefe first suggested (1980) that Earth might have a ring system of its own. An Earth ring could account for some climate events. O’Keefe remarked that formation or thickening of a ring system in Earth’s equatorial plane could drive glaciation by deepening the chill of the winter hemisphere. (It is very well established that volcanic dust is an effective agent for the extinction of sunlight; this factor can be overwhelmingly apparent in eclipse observations.) O’Keefe died in 2000 and the speculation was not pursued, but the idea of an Earth ring has a prima facie reasonableness that calls for its renewed consideration. The program of this note is to hypothesize that, as O’Keefe proposed: (a) an Earth ring system exists; (b) it affects Earth's weather and climate; (c) the tektite strewn fields comprise filaments of the ring fallen to Earth's surface on various occasions of disturbance by comets or asteroids. On this basis, and drawing on the world's weather records, together with the Twentieth Century Reanalysis by NCEP/CIRES covering the period 1870-2010 and the geology of the tektite strewn fields, we herein propose the hypothesized Earth ring

  12. Local loop near-rings

    OpenAIRE

    Franetič, Damir

    2015-01-01

    We study loop near-rings, a generalization of near-rings, where the additive structure is not necessarily associative. We introduce local loop near-rings and prove a useful detection principle for localness.

  13. Theodolite Ring Lights

    Science.gov (United States)

    Clark, David

    2006-01-01

    Theodolite ring lights have been invented to ease a difficulty encountered in the well-established optical-metrology practice of using highly reflective spherical tooling balls as position references. A theodolite ring light produces a more easily visible reflection and eliminates the need for an autocollimating device. A theodolite ring light is a very bright light source that is well centered on the optical axis of the instrument. It can be fabricated, easily and inexpensively, for use on a theodolite or telescope of any diameter.

  14. Heavy ion storage rings

    Energy Technology Data Exchange (ETDEWEB)

    Schuch, R.

    1987-01-01

    A brief overview of synchrotron storage rings for heavy ions, which are presently under construction in different accelerator laboratories is given. Ions ranging from protons up to uranium ions at MeV/nucleon energies will be injected into these rings using multiturn injection from the accelerators available or being built in these laboratories. After injection, it is planned to cool the phase space distribution of the ions by merging them with cold electron beams or laser beams, or by using stochastic cooling. Some atomic physics experiments planned for these rings are presented.

  15. Ringed Seal Distribution Map

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains GIS layers that depict the known spatial distributions (i.e., ranges) of the five subspecies of ringed seals (Phoca hispida). It was produced...

  16. The g-2 ring

    CERN Multimedia

    1974-01-01

    The precise measurement of "g-2", the anomalous magnetic moment of the muon, required a special muon storage ring with electrostatic focussing and very accurate knowledge of the magnetic bending field. For more details see under photo 7405430.

  17. Modified Newton's rings: II

    CERN Document Server

    Chaitanya, T Sai; Krishna, V Sai; Anandh, B Shankar; Umesh, K S

    2010-01-01

    In an earlier work (Shankar kumar Jha, A Vyas, O S K S Sastri, Rajkumar Jain & K S Umesh, 'Determination of wavelength of laser light using Modified Newton's rings setup', Physics Education, vol. 22, no.3, 195-202(2005)) reported by our group, a version of Newton's rings experiment called Modified Newton's rings was proposed. The present work is an extension of this work. Here, a general formula for wavelength has been derived, applicable for a plane of observation at any distance. A relation between the focal length and the radius curvature is also derived for a plano-convex lens which is essentially used as a concave mirror. Tracker, a video analysis software, freely downloadable from the net, is employed to analyze the fringes captured using a CCD camera. Two beams which give rise to interference fringes in conventional Newton's rings and in the present setup are clearly distinguished.

  18. Plastic Pollution from Ships

    OpenAIRE

    Čulin, Jelena; Bielić, Toni

    2016-01-01

    The environmental impact of shipping on marine environment includes discharge of garbage. Plastic litter is of particular concern due to abundance, resistance to degradation and detrimental effect on marine biota. According to recently published studies, a further research is required to assess human health risk. Monitoring data indicate that despite banning plastic disposal at sea, shipping is still a source of plastic pollution. Some of the measures to combat the problem are discussed.

  19. 78 FR 9451 - Academy Express, L.L.C.-Acquisition of Property-Golden Ring Travel & Transportation, Inc.

    Science.gov (United States)

    2013-02-08

    ..., customer lists, and goodwill, as well as Golden Ring's authority to render intrastate motor carrier... companies would be integrated and the purchases of fuel and other supplies would be combined, thereby...

  20. Handbook of Plastic Welding

    DEFF Research Database (Denmark)

    Islam, Aminul

    The purpose of this document is to summarize the information about the laser welding of plastic. Laser welding is a matured process nevertheless laser welding of micro dimensional plastic parts is still a big challenge. This report collects the latest information about the laser welding of plasti...... as a knowledge handbook for laser welding of plastic components. This document should provide the information for all aspects of plastic laser welding and help the design engineers to take all critical issues into consideration from the very beginning of the design phase....

  1. Plastics and health risks.

    Science.gov (United States)

    Halden, Rolf U

    2010-01-01

    By 2010, the worldwide annual production of plastics will surpass 300 million tons. Plastics are indispensable materials in modern society, and many products manufactured from plastics are a boon to public health (e.g., disposable syringes, intravenous bags). However, plastics also pose health risks. Of principal concern are endocrine-disrupting properties, as triggered for example by bisphenol A and di-(2-ethylhexyl) phthalate (DEHP). Opinions on the safety of plastics vary widely, and despite more than five decades of research, scientific consensus on product safety is still elusive. This literature review summarizes information from more than 120 peer-reviewed publications on health effects of plastics and plasticizers in lab animals and humans. It examines problematic exposures of susceptible populations and also briefly summarizes adverse environmental impacts from plastic pollution. Ongoing efforts to steer human society toward resource conservation and sustainable consumption are discussed, including the concept of the 5 Rs--i.e., reduce, reuse, recycle, rethink, restrain--for minimizing pre- and postnatal exposures to potentially harmful components of plastics.

  2. Synaptic Plasticity and Nociception

    Institute of Scientific and Technical Information of China (English)

    ChenJianguo

    2004-01-01

    Synaptic plasticity is one of the fields that progresses rapidly and has a lot of success in neuroscience. The two major types of synaptie plasticity: long-term potentiation ( LTP and long-term depression (LTD are thought to be the cellular mochanisms of learning and memory. Recently, accumulating evidence suggests that, besides serving as a cellular model for learning and memory, the synaptic plasticity involves in other physiological or pathophysiological processes, such as the perception of pain and the regulation of cardiovascular system. This minireview will focus on the relationship between synaptic plasticity and nociception.

  3. Development of Passenger Air Carriers

    Directory of Open Access Journals (Sweden)

    Igor Diminik

    2006-09-01

    Full Text Available The work presents the development of carriers in passengerair traffic, and the focus is on the development and operationsof carriers in chartered passenger transport. After the SecondWorld War, there were only scheduled air carriers. The need formass transport of tourists resulted in the development of chartercarriers or usage of scheduled carriers under different commercialconditions acceptable for tourism. Eventually also low-costcarriers appeared and they realize an increasing share in thepassenger transport especially in the aviation developed countries.

  4. Descent from the form ring and Buchsbaum rings

    CERN Document Server

    Schenzel, P

    1996-01-01

    There is a spectral sequence technique in order to estimate the local cohomology of a ring by the local cohomology of a certain form ring. As applications there are information on the descent of homological properties (Cohen-Macaulay, Buchsbaum etc.) from the form ring to the ring itself. In the case of Buchsbaum ring there is a discussion of the descent of the surjectivity of a natural map into the local cohomology.

  5. Holomorphic Dynamics and Herman Rings

    DEFF Research Database (Denmark)

    Henriksen, Christian

    1997-01-01

    Existence theorem for Herman Rings of holomorphic mappings in a certain holomorphic family is given, using quasiconformal mappings. Proofs of topological properties of these Herman rings are given.......Existence theorem for Herman Rings of holomorphic mappings in a certain holomorphic family is given, using quasiconformal mappings. Proofs of topological properties of these Herman rings are given....

  6. Maintainable substrate carrier for electroplating

    Science.gov (United States)

    Chen, Chen-An [Milpitas, CA; Abas, Emmanuel Chua [Laguna, PH; Divino, Edmundo Anida [Cavite, PH; Ermita, Jake Randal G [Laguna, PH; Capulong, Jose Francisco S [Laguna, PH; Castillo, Arnold Villamor [Batangas, PH; Ma,; Xiaobing, Diana [Saratoga, CA

    2012-07-17

    One embodiment relates to a substrate carrier for use in electroplating a plurality of substrates. The carrier includes a non-conductive carrier body on which the substrates are placed and conductive lines embedded within the carrier body. A plurality of conductive clip attachment parts are attached in a permanent manner to the conductive lines embedded within the carrier body. A plurality of contact clips are attached in a removable manner to the clip attachment parts. The contact clips hold the substrates in place and conductively connecting the substrates with the conductive lines. Other embodiments, aspects and features are also disclosed.

  7. Maintainable substrate carrier for electroplating

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Chen-An; Abas, Emmanuel Chua; Divino, Edmundo Anida; Ermita, Jake Randal G.; Capulong, Jose Francisco S.; Castillo, Arnold Villamor; Ma, Diana Xiaobing

    2016-08-02

    One embodiment relates to a substrate carrier for use in electroplating a plurality of substrates. The carrier includes a non-conductive carrier body on which the substrates are placed and conductive lines embedded within the carrier body. A plurality of conductive clip attachment parts are attached in a permanent manner to the conductive lines embedded within the carrier body. A plurality of contact clips are attached in a removable manner to the clip attachment parts. The contact clips hold the substrates in place and conductively connecting the substrates with the conductive lines. Other embodiments, aspects and features are also disclosed.

  8. Thermodynamic black di-rings

    CERN Document Server

    Iguchi, Hideo

    2010-01-01

    Previously the five dimensional $S^1$-rotating black rings have been superposed in concentric way by some solitonic methods and regular systems of two $S^1$-rotating black rings were constructed by the authors and then Evslin and Krishnan (we called these solutions black di-rings). In this place we show some characteristics of the solutions of five dimensional black di-rings, especially in thermodynamic equilibrium. After the summary of the di-ring expressions and their physical quantities, first we comment on the equivalence of the two different solution-sets of the black di-rings. Then the existence of thermodynamic black di-rings are shown, in which both iso-thermality and iso-rotation between the inner black ring and the outer black ring are realized. We also give detailed analysis of peculiar properties of the thermodynamic black di-ring including discussion about a certain kind of thermodynamic stability (instability) of the system.

  9. Ringed accretion disks: equilibrium configurations

    CERN Document Server

    Pugliese, D

    2015-01-01

    We investigate a model of ringed accretion disk, made up by several rings rotating around a supermassive Kerr black hole attractor. Each toroid of the ringed disk is governed by the General Relativity hydrodynamic Boyer condition of equilibrium configurations of rotating perfect fluids. Properties of the tori can be then determined by an appropriately defined effective potential reflecting the background Kerr geometry and the centrifugal effects. The ringed disks could be created in various regimes during the evolution of matter configurations around supermassive black holes. Therefore, both corotating and counterrotating rings have to be considered as being a constituent of the ringed disk. We provide constraints on the model parameters for the existence and stability of various ringed configurations and discuss occurrence of accretion onto the Kerr black hole and possible launching of jets from the ringed disk. We demonstrate that various ringed disks can be characterized by a maximum number of rings. We pr...

  10. Halos of Plastic

    Institute of Scientific and Technical Information of China (English)

    Maya Reid

    2012-01-01

    The halos that span South Africa's coastline are anything but angelic. Fanning out around four major urban centers-Cape Town, Port Elizabeth, East London and Durban-they are made up of innumerable bits and pieces of plastic. As a form of pollution, their shelflife is unfathomable. Plastic is essentially chemically inactive. It's designed to never break down.

  11. Biodegradation of plastics.

    Science.gov (United States)

    Shimao, M

    2001-06-01

    Widespread studies on the biodegradation of plastics have been carried out in order to overcome the environmental problems associated with synthetic plastic waste. Recent work has included studies of the distribution of synthetic polymer-degrading microorganisms in the environment, the isolation of new microorganisms for biodegradation, the discovery of new degradation enzymes, and the cloning of genes for synthetic polymer-degrading enzymes.

  12. Saturn's Other Ring Current

    Science.gov (United States)

    Crary, F. J.

    2014-04-01

    Saturn's main rings orbit the planet within an atmosphere and ionosphere of water, oxygen and hydrogen, produced by meteoritic impacts on and ultraviolet photodesorbtion of the ring particles [Johnson et al., 2006; Luhmann et al., 2006; Tseng et al., 2010]. The neutral atmosphere itself has only been tentatively detected through ultraviolet fluorescents of OH [Hall et al., 1996] while the ionosphere was observed in situ by the Cassini spacecraft shortly after orbital insertion [Coates et al.,2005; Tokar et al. 2005, Waite et al. 2005]. Although the plasma flow velocity of this ionosphere is not well-constrained, but the close association with the rings suggests that its speed would be couppled to the keplarian velocity of the rings themselves. As a result, the motion of the plasma through Saturn's magnetic field would produce an induced voltage, oriented away from the planet outside synchronous orbit and towards the planet inside synchronous orbit. Such a potential could result in currents flowing across the ring plane and closeing along magnetic field lines and through Saturn's ionosphere at latitudes between 36o and 48o. Cassini observations of whistler-mode plasma wave emissions [Xin et al.,2006] centered on synchronous orbit (1.76 Rs, mapping to 41o latitude) have been interpreted as a product of field-aligned electron beams associated with such a current. This presentation will investigate the magnitude of these currents and the resulting Joule heating of the ionosphere. An important constraint is that no auroral ultraviolet emissions have been observed at the relevant latitudes. In contrast, Joule heating could affect infrared emissions from H3+. Variations in H3+ emission associated with Saturn's rings have been reported by O'Donoghue et al., 2013, and interpreted as a result of ring "rain", i.e. precipitating water group species from the rings which alter ionosphereic chemistry and H3+ densities. As noted by O'Donoghue et al., this interpretation may be

  13. DESIGNERS’ KNOWLEDGE IN PLASTICS

    DEFF Research Database (Denmark)

    Eriksen, Kaare

    2013-01-01

    The Industrial designers’ knowledge in plastics materials and manufacturing principles of polymer products is very important for the innovative strength of the industry, according to a group of Danish plastics manufacturers, design students and practicing industrial designers. These three groups...... answered the first Danish national survey, PD13[1], investigating the importance of industrial designers’ knowledge in plastics and the collaboration between designers and the polymer industry. The plastics industry and the industrial designers collaborate well, but both groups frequently experience...... that the designers’ lack of knowledge concerning polymer materials and manufacturing methods can be problematic or annoying, and design students from most Danish design universities express the need for more contact with the industry and more competencies and tools to handle even simple topics when designing plastic...

  14. Consciousness and neural plasticity

    DEFF Research Database (Denmark)

    In contemporary consciousness studies the phenomenon of neural plasticity has received little attention despite the fact that neural plasticity is of still increased interest in neuroscience. We will, however, argue that neural plasticity could be of great importance to consciousness studies....... If consciousness is related to neural processes it seems, at least prima facie, that the ability of the neural structures to change should be reflected in a theory of this relationship "Neural plasticity" refers to the fact that the brain can change due to its own activity. The brain is not static but rather...... the relation between consciousness and brain functions. If consciousness is connected to specific brain structures (as a function or in identity) what happens to consciousness when those specific underlying structures change? It is therefore possible that the understanding and theories of neural plasticity can...

  15. Optical Leaky-Wave Antenna Integrated in Ring Resonator

    CERN Document Server

    Guclu, Caner; Boyraz, Ozdal; Capolino, Filippo

    2014-01-01

    A leaky-wave antenna at optical frequencies is designed and integrated with a ring resonator at 1550 nm wavelength. The leaky wave is generated by using periodic perturbations in the integrated dielectric waveguide that excite the -1 spatial harmonic. The antenna consists of a dielectric waveguides with semiconductor corrugations, and it is compatible with CMOS fabrication technology. We show that integrating the leaky wave antenna in an optical ring resonator that is fed by directional couplers, we can improve the electronic control of the radiation through carrier injection into the semiconductor corrugations.

  16. Glycosylation of solute carriers

    DEFF Research Database (Denmark)

    Pedersen, Nis Borbye; Carlsson, Michael C; Pedersen, Stine Helene Falsig

    2016-01-01

    as their posttranslational regulation, but only relatively little is known about the role of SLC glycosylation. Glycosylation is one of the most abundant posttranslational modifications of animal proteins and through recent advances in our understanding of protein-glycan interactions, the functional roles of SLC......Solute carriers (SLCs) are one of the largest groups of multi-spanning membrane proteins in mammals and include ubiquitously expressed proteins as well as proteins with highly restricted tissue expression. A vast number of studies have addressed the function and organization of SLCs as well...

  17. Oligomeric ferrocene rings

    Science.gov (United States)

    Inkpen, Michael S.; Scheerer, Stefan; Linseis, Michael; White, Andrew J. P.; Winter, Rainer F.; Albrecht, Tim; Long, Nicholas J.

    2016-09-01

    Cyclic oligomers comprising strongly interacting redox-active monomer units represent an unknown, yet highly desirable class of nanoscale materials. Here we describe the synthesis and properties of the first family of molecules belonging to this compound category—differently sized rings comprising only 1,1‧-disubstituted ferrocene units (cyclo[n], n = 5-7, 9). Due to the close proximity and connectivity of centres (covalent Cp-Cp linkages; Cp = cyclopentadienyl) solution voltammograms exhibit well-resolved, separated 1e- waves. Theoretical interrogations into correlations based on ring size and charge state are facilitated using values of the equilibrium potentials of these transitions, as well as their relative spacing. As the interaction free energies between the redox centres scale linearly with overall ring charge and in conjunction with fast intramolecular electron transfer (˜107 s-1), these molecules can be considered as uniformly charged nanorings (diameter ˜1-2 nm).

  18. Rings dominate western Gulf

    Science.gov (United States)

    Vidal L., Francisco V.; Vidal L., Victor M. V.; Molero, José María Pérez

    Surface and deep circulation of the central and western Gulf of Mexico is controlled by interactions of rings of water pinched from the gulf's Loop Current. The discovery was made by Mexican oceanographers who are preparing a full-color, 8-volume oceanographic atlas of the gulf.Anticyclonic warm-core rings pinch off the Loop Current at a rate of about one to two per year, the scientists of the Grupo de Estudios Oceanográficos of the Instituto de Investigaciones Eléctricas (GEO-IIE) found. The rings migrate west until they collide with the continental shelf break of the western gulf, almost always between 22° and 23°N latitude. On their westward travel they transfer angular momentum and vorticity to the surrounding water, generating cyclonic circulations and vortex pairs that completely dominate the entire surface and deep circulation of the central and western gulf.

  19. Autocatalytic chemical smoke rings

    CERN Document Server

    Rogers, M C; Rogers, Michael C.; Morris, Stephen W.

    2005-01-01

    Buoyant plumes, evolving free of boundary constraints, may develop well-defined mushroom shaped heads. In normal plumes, overturning flow in the head entrains less buoyant fluid from the surroundings as the head rises, robbing the plume of its driving force. We consider here a new type of plume in which the source of buoyancy is an autocatalytic chemical reaction. The reaction occurs at a sharp front which separates reactants from less dense products. In this type of plume, entrainment assists the reaction, producing new buoyancy which fuels an accelerating plume head. When the head has grown to a critical size, it detaches from the upwelling conduit, forming an accelerating, buoyant vortex ring. This vortex is analogous to a rising smoke ring. A second-generation head then develops at the point of detachment.Multiple generations of chemical vortex rings can detach from a single triggering event.

  20. Decay ring design

    CERN Document Server

    Chancé, A; Bouquerel, E; Hancock, S; Jensen, E

    The study of the neutrino oscillation between its different flavours needs pureand very intense fluxes of high energy, well collimated neutrinos with a welldetermined energy spectrum. A dedicated machine seems to be necessarynowadays to reach the required flux. A new concept based on the β-decayof radioactive ions which were accelerated in an accelerator chain was thenproposed. After ion production, stripping, bunching and acceleration, the unstableions are then stored in a racetrack-shaped superconducting decay ring.Finally, the ions are accumulated in the decay ring until being lost. The incomingbeam is merged to the stored beam by using a specific RF system, whichwill be presented here.We propose here to study some aspects of the decay ring, such as its opticalproperties, its RF system or the management of the losses which occur in thering (mainly by decay or by collimation).

  1. Almost ring theory

    CERN Document Server

    2003-01-01

    This book develops thorough and complete foundations for the method of almost etale extensions, which is at the basis of Faltings' approach to p-adic Hodge theory. The central notion is that of an "almost ring". Almost rings are the commutative unitary monoids in a tensor category obtained as a quotient V-Mod/S of the category V-Mod of modules over a fixed ring V; the subcategory S consists of all modules annihilated by a fixed ideal m of V, satisfying certain natural conditions. The reader is assumed to be familiar with general categorical notions, some basic commutative algebra and some advanced homological algebra (derived categories, simplicial methods). Apart from these general prerequisites, the text is as self-contained as possible. One novel feature of the book - compared with Faltings' earlier treatment - is the systematic exploitation of the cotangent complex, especially for the study of deformations of almost algebras.

  2. On Simple Noetherian Rings

    Institute of Scientific and Technical Information of China (English)

    Somyot Plubtieng

    2003-01-01

    A module M is called a CS-module (or extending module [5]) if every submodule of M is essential in a direct summand of M. It is shown that (i) a simple ring R is right noetherian if and only if every cyclic singular right R-module is either a CS-module or a noetherian module; (ii) for a prime ring R, if every proper cyclic right R-module is a direct sum of a quasi-injective module and a finitely cogenerated module, then R is either semisimple artinian or a right Ore domain; and (iii) a prime ring R is right noetherian if and only if every cyclic right R-module is a direct sum of a quasi-injective module and a noetherian module.

  3. Tunneling Through Black Rings

    Institute of Scientific and Technical Information of China (English)

    ZHAO Liu

    2007-01-01

    Hawking radiation of black ring solutions to 5-dimensional Einstein-Maxwell-dilaton theory is analyzed by use of the Parikh-Wilczek tunneling method. To get the correct tunneling amplitude and emission rate, we adopt and develop the Angheben-Nadalini-Vanzo-Zerbini covariant approach to cover the effects of rotation and electronic discharge all at once, and the effect of back reaction is also taken into account. This constitutes a unified approach to the tunneling problem. Provided the first law of thermodynamics for black rings holds, the emission rate is proportional to the exponential of the change of Bekenstein-Hawking entropy. Explicit calculation for black ring temperatures agrees exactly with the results obtained via the classical surface gravity method and the quasi-local formalism.

  4. Deployable Fresnel Rings

    Science.gov (United States)

    Kennedy, Timothy F.; Fink, Patrick W.; Chu, Andrew W.; Lin, Gregory Y.

    2014-01-01

    Deployable Fresnel rings (DFRs) significantly enhance the realizable gain of an antenna. This innovation is intended to be used in combination with another antenna element, as the DFR itself acts as a focusing or microwave lens element for a primary antenna. This method is completely passive, and is also completely wireless in that it requires neither a cable, nor a connector from the antenna port of the primary antenna to the DFR. The technology improves upon the previous NASA technology called a Tri-Sector Deployable Array Antenna in at least three critical aspects. In contrast to the previous technology, this innovation requires no connector, cable, or other physical interface to the primary communication radio or sensor device. The achievable improvement in terms of antenna gain is significantly higher than has been achieved with the previous technology. Also, where previous embodiments of the Tri-Sector antenna have been constructed with combinations of conventional (e.g., printed circuit board) and conductive fabric materials, this innovation is realized using only conductive and non-conductive fabric (i.e., "e-textile") materials, with the possible exception of a spring-like deployment ring. Conceptually, a DFR operates by canceling the out-of-phase radiation at a plane by insertion of a conducting ring or rings of a specific size and distance from the source antenna, defined by Fresnel zones. Design of DFRs follow similar procedures to those outlined for conventional Fresnel zone rings. Gain enhancement using a single ring is verified experimentally and through computational simulation. The experimental test setup involves a microstrip patch antenna that is directly behind a single-ring DFR and is radiating towards a second microstrip patch antenna. The first patch antenna and DFR are shown. At 2.42 GHz, the DFR improves the transmit antenna gain by 8.6 dB, as shown in Figure 2, relative to the wireless link without the DFR. A figure illustrates the

  5. Saturn's rings - high resolution

    Science.gov (United States)

    1981-01-01

    Voyager 2 obtained this high-resolution picture of Saturn's rings Aug. 22, when the spacecraft was 4 million kilometers (2.5 million miles) away. Evident here are the numerous 'spoke' features, in the B-ring; their very sharp, narrow appearance suggests short formation times. Scientists think electromagnetic forces are responsible in some way for these features, but no detailed theory has been worked out. Pictures such as this and analyses of Voyager 2's spoke movies may reveal more clues about the origins of these complex structures. The Voyager project is managed for NASA by the Jet Propulsion Laboratory, Pasadena, Calif.

  6. From macro- to microplastics - Analysis of EU regulation along the life cycle of plastic bags.

    Science.gov (United States)

    Steensgaard, Ida M; Syberg, Kristian; Rist, Sinja; Hartmann, Nanna B; Boldrin, Alessio; Hansen, Steffen Foss

    2017-05-01

    Plastic pollution and its environmental effects has received global attention the recent years. However, limited attention has so far been directed towards how plastics are regulated in a life cycle perspective and how regulatory gaps can be addressed in order to limit and prevent environmental exposure and hazards of macro- and microplastics. In this paper, we map European regulation taking outset in the life cycle perspective of plastic carrier bags: from plastic bag production to when it enters the environment. Relevant regulatory frameworks, directives and authorities along the life cycle are identified and their role in regulation of plastics is discussed. Most important regulations were identified as: the EU chemical Regulation, the Packaging and Packaging Waste Directive including the amending Directive regarding regulation of the consumption of lightweight plastic carrier bags, the Waste Framework Directive and the Directive on the Landfill of Waste. The main gaps identified relate to lack of clear definitions of categories of polymers, unambitious recycling rates and lack of consideration of macro- and microplastics in key pieces of legislation. We recommend that polymers are categorized according to whether they are polymers with the same monomer constituents (homopolymers) or with different monomer constituents (copolymers) and that polymers are no longer exempt from registration and evaluation under REACH. Plastics should furthermore have the same high level of monitoring and reporting requirements as hazardous waste involving stricter requirements to labelling, recordkeeping, monitoring and control over the whole lifecycle. Finally, we recommend that more ambitious recycle and recovery targets are set across the EU. Regulation of the consumption of lightweight plastic carrier bags should also apply to heavyweight plastic carrier bags. Last, the Marine and Water Framework Directives should specifically address plastic waste affecting water quality

  7. Ring chromosome 13

    DEFF Research Database (Denmark)

    Brandt, C A; Hertz, Jens Michael; Petersen, M B;

    1992-01-01

    A stillborn male child with anencephaly and multiple malformations was found to have the karyotype 46,XY,r(13) (p11q21.1). The breakpoint at 13q21.1, determined by high resolution banding, is the most proximal breakpoint ever reported in patients with ring chromosome 13. In situ hybridisation...

  8. Planetary ring systems

    CERN Document Server

    Miner, Ellis D; Cuzzi, Jeffrey N

    2007-01-01

    This is the most comprehensive and up-to-date book on the topic of planetary rings systems yet written. The book is written in a style that is easily accessible to the interested non expert. Each chapter includes notes, references, figures and tables.

  9. On topologies over rings

    Directory of Open Access Journals (Sweden)

    Syed M. Fakhruddin

    1985-01-01

    Full Text Available In this note, we show that if a topology F¯ over a ring A satisfies a certain finiteness condition, then the Gabriel topology G¯ generated by F¯ can be explicitly constructed and it also satisfies the same finiteness condition.

  10. Fusion Rings for Quantum Groups

    DEFF Research Database (Denmark)

    2012-01-01

    We study the fusion rings of tilting modules for a quantum group at a root of unity modulo the tensor ideal of negligible tilting modules. We identify them in type A with the combinatorial rings from [12] and give a similar description of the sp2n-fusion ring in terms of noncommutative symmetric...... functions. Moreover we give a presentation of all fusion rings in classical types as quotients of polynomial rings. Finally we also compute the fu- sion rings for type G2....

  11. Fusion Rings for Quantum Groups

    DEFF Research Database (Denmark)

    Andersen, Henning Haahr; Stroppel, Catharina

    2012-01-01

    We study the fusion rings of tilting modules for a quantum group at a root of unity modulo the tensor ideal of negligible tilting modules. We identify them in type A with the combinatorial rings from [12] and give a similar description of the sp2n-fusion ring in terms of noncommutative symmetric...... functions. Moreover we give a presentation of all fusion rings in classical types as quotients of polynomial rings. Finally we also compute the fu- sion rings for type G2....

  12. Rings from Close Encounters

    Science.gov (United States)

    Kohler, Susanna

    2016-09-01

    Weve recently discovered narrow sets of rings around two minor planets orbiting in our solar system. How did these rings form? A new study shows that they could be a result of close encounters between the minor planets and giants like Jupiter or Neptune.Unexpected Ring SystemsPositions of the centaurs in our solar system (green). Giant planets (red), Jupiter trojans (grey), scattered disk objects (tan) and Kuiper belt objects (blue) are also shown. [WilyD]Centaurs are minor planets in our solar system that orbit between Jupiter and Neptune. These bodies of which there are roughly 44,000 with diameters larger than 1 km have dynamically unstable orbits that cross paths with those of one or more giant planets.Recent occultation observations of two centaurs, 10199 Chariklo and 2060 Chiron, revealed that these bodies both host narrow ring systems. Besides our four giant planets, Chariklo and Chiron are the only other bodies in the solar system known to have rings. But how did these rings form?Scientists have proposed several models, implicating collisions, disruption of a primordial satellite, or dusty outgassing. But a team of scientists led by Ryuki Hyodo (Paris Institute of Earth Physics, Kobe University) has recently proposed an alternative scenario: what if the rings were formed from partial disruption of the centaur itself, after it crossed just a little too close to a giant planet?Tidal Forces from a GiantHyodo and collaborators first used past studies of centaur orbits to estimate that roughly 10% of centaurs experience close encounters (passing within a distance of ~2x the planetary radius) with a giant planet during their million-year lifetime. The team then performed a series of simulations of close encounters between a giant planet and a differentiated centaur a body in which the rocky material has sunk to form a dense silicate core, surrounded by an icy mantle.Some snapshots of simulation outcomes (click for a closer look!) for different initial states of

  13. LIQUIFIED NATURAL GAS (LNG CARRIERS

    Directory of Open Access Journals (Sweden)

    Daniel Posavec

    2010-12-01

    Full Text Available Modern liquefied natural gas carriers are double-bottom ships classified according to the type of LNG tank. The tanks are specially designed to store natural gas cooled to -161°C, the boiling point of methane. Since LNG is highly flammable, special care must be taken when designing and operating the ship. The development of LNG carriers has begun in the middle of the twentieth century. LNG carrier storage space has gradually grown to the current maximum of 260000 m3. There are more than 300 LNG carriers currently in operation (the paper is published in Croatian.

  14. Informative document waste plastics

    NARCIS (Netherlands)

    Nagelhout D; Sein AA; Duvoort GL

    1989-01-01

    This "Informative document waste plastics" forms part of a series of "informative documents waste materials". These documents are conducted by RIVM on the indstruction of the Directorate General for the Environment, Waste Materials Directorate, in behalf of the program of

  15. A Plastic Menagerie

    Science.gov (United States)

    Hadley, Mary Jane

    2010-01-01

    Bobble heads had become quite popular, depicting all sorts of sports figures, animals, and even presidents. In this article, the author describes how her fourth graders made bobble head sculptures out of empty plastic drink bottles. (Contains 1 online resource.)

  16. Cortical plasticity and rehabilitation.

    Science.gov (United States)

    Moucha, Raluca; Kilgard, Michael P

    2006-01-01

    The brain is constantly adapting to environmental and endogenous changes (including injury) that occur at every stage of life. The mechanisms that regulate neural plasticity have been refined over millions of years. Motivation and sensory experience directly shape the rewiring that makes learning and neurological recovery possible. Guiding neural reorganization in a manner that facilitates recovery of function is a primary goal of neurological rehabilitation. As the rules that govern neural plasticity become better understood, it will be possible to manipulate the sensory and motor experience of patients to induce specific forms of plasticity. This review summarizes our current knowledge regarding factors that regulate cortical plasticity, illustrates specific forms of reorganization induced by control of each factor, and suggests how to exploit these factors for clinical benefit.

  17. Mechanical plasticity of cells

    Science.gov (United States)

    Bonakdar, Navid; Gerum, Richard; Kuhn, Michael; Spörrer, Marina; Lippert, Anna; Schneider, Werner; Aifantis, Katerina E.; Fabry, Ben

    2016-10-01

    Under mechanical loading, most living cells show a viscoelastic deformation that follows a power law in time. After removal of the mechanical load, the cell shape recovers only incompletely to its original undeformed configuration. Here, we show that incomplete shape recovery is due to an additive plastic deformation that displays the same power-law dynamics as the fully reversible viscoelastic deformation response. Moreover, the plastic deformation is a constant fraction of the total cell deformation and originates from bond ruptures within the cytoskeleton. A simple extension of the prevailing viscoelastic power-law response theory with a plastic element correctly predicts the cell behaviour under cyclic loading. Our findings show that plastic energy dissipation during cell deformation is tightly linked to elastic cytoskeletal stresses, which suggests the existence of an adaptive mechanism that protects the cell against mechanical damage.

  18. Targeting tumour Cell Plasticity

    Institute of Scientific and Technical Information of China (English)

    Elizabeth D. WILLIAMS

    2009-01-01

    @@ Her research is focused on understanding the mechanisms of tumour progression and metastasis, particularly in uro-logical carcinomas (bladder and prostate). Tumour cell plasticity, including epithelial-mesenchymal transition, is a cen-tral theme in Dr Williams' work.

  19. Laser cutting plastic materials

    Energy Technology Data Exchange (ETDEWEB)

    Van Cleave, R.A.

    1980-08-01

    A 1000-watt CO/sub 2/ laser has been demonstrated as a reliable production machine tool for cutting of plastics, high strength reinforced composites, and other nonmetals. More than 40 different plastics have been laser cut, and the results are tabulated. Applications for laser cutting described include fiberglass-reinforced laminates, Kevlar/epoxy composites, fiberglass-reinforced phenolics, nylon/epoxy laminates, ceramics, and disposable tooling made from acrylic.

  20. Localization of plastic deformation

    Energy Technology Data Exchange (ETDEWEB)

    Rice, J R

    1976-04-01

    The localization of plastic deformation into a shear band is discussed as an instability of plastic flow and a precursor to rupture. Experimental observations are reviewed, a general theoretical framework is presented, and specific calculations of critical conditions are carried out for a variety of material models. The interplay between features of inelastic constitutive description, especially deviations from normality and vertex-like yielding, and the onset of localization is emphasized.

  1. PENGARUH PLASTICIZER PADA KARAKTERISTIK EDIBLE FILM DARI PEKTIN

    Directory of Open Access Journals (Sweden)

    Sang Kompiang Wirawan

    2012-05-01

    Full Text Available EFFECT OF PLASTICIzER ON THE PECTINIC EDIBLE FILM CHARACTERISTICS. The peel of Balinese Citrus contains high concentration of pectin which can be further processed to be edible films. The edible films can be utilized as a food coating which protects the food from any external mass transports such as humid, oxygen, and soluble material and can be served as a carrier to improve the mechanical-handing properties of the food. Edible films made of organic polymers tend to be brittle and thus addition of a plasticizer is required during the process. The work studies the effect of the type and the concentration of plasticizers on the tensile strength, the elongation of break, and the water vapor permeabilty of the edible film. Sorbitol and glycerol were used as plasticizers. Albedo from the citrus was hydrolized with hydrochloride acid 0.1 N to get pectinate substance. Pectin was then dissolved in water dan mixed with the plasticizers and CaCl2.2H2O solution. The concentrations of the plasticizers were 0, 0.03, 0.05, 0.1, and 0.15 mL/mL of solution. The results showed that increasing the concentration of plasticizers will decrease the tensile strength, but increase the elongation and film permeability. Sorbitol-plasticized films are more brittle, however exhibited higher tensile strength and water vapor permeability than of glycerol-plasticized film. The results suggested that glycerol is better plasticizer than sorbitol.  Kulit jeruk bali banyak mengandung pektin yang dapat dimanfaatkan sebagai bahan baku edible film. Edible film bisa digunakan untuk melapisi bahan makanan, melindungi makanan dari transfer massa eksternal seperti kelembaban, oksigen, dan zat terlarut, serta dapat digunakan sebagai carrier untuk meningkatkan penanganan mekanik produk makanan. Film yang terbuat dari bahan polimer organik ini cenderung rapuh sehingga diperlukan penambahan plasticizer. Tujuan dari penelitian ini adalah untuk mengetahui pengaruh kadar dan jenis

  2. Synchronization in multicell systems exhibiting dynamic plasticity

    Indian Academy of Sciences (India)

    C Suguna; Somdatta Sinha

    2008-08-01

    Collective behaviour in multicell systems arises from exchange of chemicals/signals between cells and may be different from their intrinsic behaviour. These chemicals are products of regulated networks of biochemical pathways that underlie cellular functions, and can exhibit a variety of dynamics arising from the non-linearity of the reaction processes. We have addressed the emergent synchronization properties of a ring of cells, diffusively coupled by the end product of an intracellular model biochemical pathway exhibiting non-robust birhythmic behaviour. The aim is to examine the role of intercellular interaction in stabilizing the non-robust dynamics in the emergent collective behaviour in the ring of cells. We show that, irrespective of the inherent frequencies of individual cells, depending on the coupling strength, the collective behaviour does synchronize to only one type of oscillations above a threshold number of cells. Using two perturbation analyses, we also show that this emergent synchronized dynamical state is fairly robust under external perturbations. Thus, the inherent plasticity in the oscillatory phenotypes in these model cells may get suppressed to exhibit collective dynamics of a single type in a multicell system, but environmental influences can sometimes expose this underlying plasticity in its collective dynamics.

  3. Development of plastic surgery

    Directory of Open Access Journals (Sweden)

    Pećanac Marija Đ.

    2015-01-01

    Full Text Available Introduction. Plastic surgery is a medical specialty dealing with corrections of defects, improvements in appearance and restoration of lost function. Ancient Times. The first recorded account of reconstructive plastic surgery was found in ancient Indian Sanskrit texts, which described reconstructive surgeries of the nose and ears. In ancient Greece and Rome, many medicine men performed simple plastic cosmetic surgeries to repair damaged parts of the body caused by war mutilation, punishment or humiliation. In the Middle Ages, the development of all medical braches, including plastic surgery was hindered. New age. The interest in surgical reconstruction of mutilated body parts was renewed in the XVIII century by a great number of enthusiastic and charismatic surgeons, who mastered surgical disciplines and became true artists that created new forms. Modern Era. In the XX century, plastic surgery developed as a modern branch in medicine including many types of reconstructive surgery, hand, head and neck surgery, microsurgery and replantation, treatment of burns and their sequelae, and esthetic surgery. Contemporary and future plastic surgery will continue to evolve and improve with regenerative medicine and tissue engineering resulting in a lot of benefits to be gained by patients in reconstruction after body trauma, oncology amputation, and for congenital disfigurement and dysfunction.

  4. Ring autosomes: some unexpected findings.

    Science.gov (United States)

    Caba, L; Rusu, C; Plăiaşu; Gug, G; Grămescu, M; Bujoran, C; Ochiană, D; Voloşciuc, M; Popescu, R; Braha, E; Pânzaru, M; Butnariu, L; Sireteanu, A; Covic, M; Gorduza, Ev

    2012-12-01

    Ring chromosomes are rare entities, usually associated with phenotypic abnormalities in correlation with the loss of genetic material. There are various breakpoints and sometimes there is a dynamic mosaicism that is reflected in clinical features. Most of the ring chromosomes are de novo occurrences. Our study reflects the experience of three Romanian cytogenetic laboratories in the field of ring chromosomes. We present six cases with ring chromosomes involving chromosomes 5, 13, 18, and 21. All ring chromosomes were identified after birth in children with plurimalformative syndromes. The ring chromosome was present in mosaic form in three cases, and this feature reflects the ring's instability. In case of ring chromosome 5, we report a possible association with oculo-auriculo-vertebral spectrum.

  5. Sorting Plastic Waste in Hydrocyclone

    Directory of Open Access Journals (Sweden)

    Ernestas Šutinys

    2011-02-01

    Full Text Available The article presents material about sorting plastic waste in hydrocyclone. The tests on sorting plastic waste were carried out. Also, the findings received from the performed experiment on the technology of sorting plastic waste are interpreted applying an experimental model of the equipment used for sorting plastics of different density.Article in Lithuanian

  6. Chemical leucoderma induced by ear-ring stoppers made of polyvinyl chloride

    Directory of Open Access Journals (Sweden)

    Reena Sharma

    2012-01-01

    Full Text Available We report a case of chemical leucoderma (CL in a 15-year-old girl, who developed patterned depigmentation at the back of both ear lobules after contact with plastic ear-ring stoppers made of polyvinyl chloride (PVC after continuous use for 6-7 months. Patch test with Indian standard series and cosmetic series was negative after 48 h, but she refused patch testing for extended duration as the possibility of induced depigmentation at the test site was unacceptable to her. To the best of our knowledge, this is the first report of plastic ear-ring stopper induced CL.

  7. The Effects of Forming Parameters on Conical Ring Rolling Process

    Directory of Open Access Journals (Sweden)

    Wen Meng

    2014-01-01

    Full Text Available The plastic penetration condition and biting-in condition of a radial conical ring rolling process with a closed die structure on the top and bottom of driven roll, simplified as RCRRCDS, were established. The reasonable value range of mandrel feed rate in rolling process was deduced. A coupled thermomechanical 3D FE model of RCRRCDS process was established. The changing laws of equivalent plastic strain (PEEQ and temperature distributions with rolling time were investigated. The effects of ring’s outer radius growth rate and rolls sizes on the uniformities of PEEQ and temperature distributions, average rolling force, and average rolling moment were studied. The results indicate that the PEEQ at the inner layer and outer layer of rolled ring are larger than that at the middle layer of ring; the temperatures at the “obtuse angle zone” of ring’s cross-section are higher than those at “acute angle zone”; the temperature at the central part of ring is higher than that at the middle part of ring’s outer surfaces. As the ring’s outer radius growth rate increases at its reasonable value ranges, the uniformities of PEEQ and temperature distributions increase. Finally, the optimal values of the ring’s outer radius growth rate and rolls sizes were obtained.

  8. A Mandrel Feeding Strategy in Conical Ring Rolling Process

    Directory of Open Access Journals (Sweden)

    Wen Meng

    2014-01-01

    Full Text Available A mathematical model for radial conical ring rolling with a closed die structure on the top and bottom of driven roll, simplified as RCRRCDS, was established. The plastic penetration and biting-in conditions in RCRRCDS process were determined. A mandrel feeding strategy for RCRRCDS process was proposed. The mandrel feed rate and its reasonable value range were deduced. The coupled thermal-mechanical FE model of RCRRCDS process was established. The reasonable value range of the mandrel feed rate was verified by using numerical simulation method. The results indicate that the reasonable value range of the mandrel feed rate is feasible, the proposed mandrel feeding strategy can realize a steady RCRRCDS process, and the forming quality of conical ring rolled by using the proposed feeding strategy is better than that of conical ring rolled by using a constant mandrel feed rate.

  9. On Skew Triangular Matrix Rings

    Institute of Scientific and Technical Information of China (English)

    Wang Wei-liang; Wang Yao; Ren Yan-li

    2016-01-01

    Letαbe a nonzero endomorphism of a ring R, n be a positive integer and Tn(R,α) be the skew triangular matrix ring. We show that some properties related to nilpotent elements of R are inherited by Tn(R,α). Meanwhile, we determine the strongly prime radical, generalized prime radical and Behrens radical of the ring R[x;α]/(xn), where R[x;α] is the skew polynomial ring.

  10. e-læring

    DEFF Research Database (Denmark)

    Helms, Niels Henrik

    e-læring kan defineres på ganske mange måder. Ordet e-læring består jo tydeligt nok af to elementer. E + læring ligesom e-handel eller e-banking, og umiddelbart vil de fleste nok sige, at det så handler om læring vha. internettet. I bidraget advokeres for en læringsmæssig frem for normativ tilgang....

  11. The Black Ring is Unstable

    CERN Document Server

    Santos, Jorge E

    2015-01-01

    We study non-axisymmetric linearised gravitational perturbations of the Emparan-Reall black ring using numerical methods. We find an unstable mode whose onset lies within the "fat" branch of the black ring and continues into the "thin" branch. Together with previous results using Penrose inequalities that fat black rings are unstable, this provides numerical evidence that the entire black ring family is unstable.

  12. A Database of Invariant Rings

    OpenAIRE

    Kemper, Gregor; Körding, Elmar; Malle, Gunter; Matzat, B. Heinrich; Vogel, Denis; Wiese, Gabor

    2001-01-01

    We announce the creation of a database of invariant rings. This database contains a large number of invariant rings of finite groups, mostly in the modular case. It gives information on generators and structural properties of the invariant rings. The main purpose is to provide a tool for researchers in invariant theory.

  13. Integrated silicon optofluidic ring resonator

    NARCIS (Netherlands)

    Testa, G.; Huang, Y.; Sarro, P.M.; Zeni, L.; Bernini, R.

    2010-01-01

    The feasibility of an integrated silicon optofluidic ring resonator is demonstrated. Liquid core antiresonant reflecting optical waveguides are used to realize a rectangular ring resonator with a multimode interference liquid core coupler between the ring and the bus waveguide. In this configuration

  14. Non-Commutative Ring Theory

    CERN Document Server

    López-Permouth, Sergio

    1990-01-01

    The papers of this volume share as a common goal the structure and classi- fication of noncommutative rings and their modules, and deal with topics of current research including: localization, serial rings, perfect endomorphism rings, quantum groups, Morita contexts, generalizations of injectivitiy, and Cartan matrices.

  15. Ring closure in actin polymers

    Science.gov (United States)

    Sinha, Supurna; Chattopadhyay, Sebanti

    2017-03-01

    We present an analysis for the ring closure probability of semiflexible polymers within the pure bend Worm Like Chain (WLC) model. The ring closure probability predicted from our analysis can be tested against fluorescent actin cyclization experiments. We also discuss the effect of ring closure on bend angle fluctuations in actin polymers.

  16. RINGED ACCRETION DISKS: EQUILIBRIUM CONFIGURATIONS

    Energy Technology Data Exchange (ETDEWEB)

    Pugliese, D.; Stuchlík, Z., E-mail: d.pugliese.physics@gmail.com, E-mail: zdenek.stuchlik@physics.cz [Institute of Physics and Research Centre of Theoretical Physics and Astrophysics, Faculty of Philosophy and Science, Silesian University in Opava, Bezručovo náměstí 13, CZ-74601 Opava (Czech Republic)

    2015-12-15

    We investigate a model of a ringed accretion disk, made up by several rings rotating around a supermassive Kerr black hole attractor. Each toroid of the ringed disk is governed by the general relativity hydrodynamic Boyer condition of equilibrium configurations of rotating perfect fluids. Properties of the tori can then be determined by an appropriately defined effective potential reflecting the background Kerr geometry and the centrifugal effects. The ringed disks could be created in various regimes during the evolution of matter configurations around supermassive black holes. Therefore, both corotating and counterrotating rings have to be considered as being a constituent of the ringed disk. We provide constraints on the model parameters for the existence and stability of various ringed configurations and discuss occurrence of accretion onto the Kerr black hole and possible launching of jets from the ringed disk. We demonstrate that various ringed disks can be characterized by a maximum number of rings. We present also a perturbation analysis based on evolution of the oscillating components of the ringed disk. The dynamics of the unstable phases of the ringed disk evolution seems to be promising in relation to high-energy phenomena demonstrated in active galactic nuclei.

  17. Adaptive plasticity in wild field cricket's acoustic signaling.

    Directory of Open Access Journals (Sweden)

    Susan M Bertram

    Full Text Available Phenotypic plasticity can be adaptive when phenotypes are closely matched to changes in the environment. In crickets, rhythmic fluctuations in the biotic and abiotic environment regularly result in diel rhythms in density of sexually active individuals. Given that density strongly influences the intensity of sexual selection, we asked whether crickets exhibit plasticity in signaling behavior that aligns with these rhythmic fluctuations in the socio-sexual environment. We quantified the acoustic mate signaling behavior of wild-caught males of two cricket species, Gryllus veletis and G. pennsylvanicus. Crickets exhibited phenotypically plastic mate signaling behavior, with most males signaling more often and more attractively during the times of day when mating activity is highest in the wild. Most male G. pennsylvanicus chirped more often and louder, with shorter interpulse durations, pulse periods, chirp durations, and interchirp durations, and at slightly higher carrier frequencies during the time of the day that mating activity is highest in the wild. Similarly, most male G. veletis chirped more often, with more pulses per chirp, longer interpulse durations, pulse periods, and chirp durations, shorter interchirp durations, and at lower carrier frequencies during the time of peak mating activity in the wild. Among-male variation in signaling plasticity was high, with some males signaling in an apparently maladaptive manner. Body size explained some of the among-male variation in G. pennsylvanicus plasticity but not G. veletis plasticity. Overall, our findings suggest that crickets exhibit phenotypically plastic mate attraction signals that closely match the fluctuating socio-sexual context they experience.

  18. Saturn's ``Gossamer'' Ring: The F Ring's Inner Sheet

    Science.gov (United States)

    Showalter, M. R.; Burns, J. A.; Hamilton, D. P.

    1998-09-01

    Recent Galileo and Earth-based images have revealed for the first time that Jupiter's ``gossamer'' ring is actually composed of two rings, one bounded at the outer edge by Amalthea and the other bounded by Thebe. Dynamical models suggest that these rings are composed of dust grains ejected off the surfaces of the two moons, which then evolve inward under Poynting-Robertson drag. A very faint sheet of material filling the region between Saturn's A and F Rings reported by Burns et al. (BAAS 15, 1013--1014, 1983) may be a dynamically analogous system, in which dust escapes from the F Ring and evolves inward to the A Ring. Unlike Jupiter's gossamer rings, however, the inner sheet of Saturn's F Ring has been well observed from a large range of phase angles and visual wavelengths by Voyager. Voyager images reveal that this faint ring shows a tenfold increase in brightness between phase angles of 125(deg) and 165(deg) , indicating that it is composed of fine dust microns in size. Preliminary estimates of the normal optical depth fall in the range 1--2*E(-4) , depending on the dust size distribution assumed. Initial spectrophotometry reveals that the ring is neutral in color. The ring is uniform in brightness over the entire region between the two rings, with no evidence for internal structure associated with Prometheus and Atlas, suggesting that neither of these embedded moons acts as either a source or a sink. We will refine the aforementioned measurements and develop photometric models to better constrain the properties of the dust in this ring. This will enable us to relate the dust population to that in the F Ring proper, and to better explore the dynamical processes at work.

  19. Computational studies of carbodiimide rings.

    Science.gov (United States)

    Damrauer, Robert; Lin, Hai; Damrauer, Niels H

    2014-05-02

    Computational studies of alicyclic carbodiimides (RN═C═NR) (rings five through twelve) at the MP2/6-31G(d,p)//MP2/6-31G(d,p) level of theory were conducted to locate the transition states between carbodiimides isomers. Transition states for rings six through twelve were found. The RNCNR dihedral angle is ∼0° for even-numbered rings, but deviates from 0° for rings seven, nine, eleven, and twelve. The even- and odd-numbered ring transition states have different symmetry point groups. Cs transition states (even rings) have an imaginary frequency mode that transforms as the asymmetric irreducible representation of the group. C2 transition states (odd rings) have a corresponding mode that transforms as the totally symmetric representation. Intrinsic reaction coordinate analyses followed by energy minimization along the antisymmetric pathways led to enantiomeric pairs. The symmetric pathways give diastereomeric isomers. The five-membered ring carbodiimide is a stable structure, possibly isolable. A twelve-membered ring transition state was found only without applying symmetry constraints (C1). Molecular mechanics and molecular dynamics studies of the seven-, eight-, and nine-membered rings gave additional structures, which were then minimized using ab initio methods. No structures beyond those found from the IRC analyses described were found. The potential for optical resolution of the seven-membered ring is discussed.

  20. 42 CFR 421.200 - Carrier functions.

    Science.gov (United States)

    2010-10-01

    ... 42 Public Health 3 2010-10-01 2010-10-01 false Carrier functions. 421.200 Section 421.200 Public...) MEDICARE PROGRAM MEDICARE CONTRACTING Carriers § 421.200 Carrier functions. A contract between CMS and a carrier specifies the functions to be performed by the carrier. The contract may include any or all of...

  1. Magnetic fields in ring galaxies

    CERN Document Server

    Moss, D; Silchenko, O; Sokoloff, D; Horellou, C; Beck, R

    2016-01-01

    Many galaxies contain magnetic fields supported by galactic dynamo action. However, nothing definitive is known about magnetic fields in ring galaxies. Here we investigate large-scale magnetic fields in a previously unexplored context, namely ring galaxies, and concentrate our efforts on the structures that appear most promising for galactic dynamo action, i.e. outer star-forming rings in visually unbarred galaxies. We use tested methods for modelling $\\alpha-\\Omega$ galactic dynamos, taking into account the available observational information concerning ionized interstellar matter in ring galaxies. Our main result is that dynamo drivers in ring galaxies are strong enough to excite large-scale magnetic fields in the ring galaxies studied. The variety of dynamo driven magnetic configurations in ring galaxies obtained in our modelling is much richer than that found in classical spiral galaxies. In particular, various long-lived transients are possible. An especially interesting case is that of NGC 4513 where th...

  2. A season in Saturn's rings: Cycling, recycling and ring history

    Science.gov (United States)

    Esposito, L. W.; Meinke, B. K.; Albers, N.; Sremcevic, M.

    2012-04-01

    Cassini experiments have watched Saturn's ring system evolve before our eyes. Images and occultations show changes and transient events. The rings are a dynamic and complex geophysical system, incompletely modeled as a single-phase fluid. Key Cassini observations: High resolution images show straw, propellers, embedded moonlets, and F ring objects. Multiple UVIS, RSS and VIMS occutlations indicate multimodal ringlet and edge structure, including free and forced modes along with stochastic perturbations that are most likely caused by nearby mass concentrations. Vertical excursions are evident at ring edges and in other perturbed regions. The rings are occasionally hit by meteorites that leave a signature that may last centuries; meteoritic dust pollutes the rings. Temperature, reflectance and transmission spectra are influenced by the dynamical state of the ring particles. Saturn's Equinox 2009: Oblique lighting exposed vertical structure and embedded objects. The rings were the coldest ever. Images inspired new occultation and spectral analysis that show abundant structure in the perturbed regions. The rings are more variable and complex than we had expected prior to this seasonal viewing geometry. Sub-kilometer structure in power spectral analysis: Wavelet analysis shows features in the strongest density waves and at the shepherded outer edge of the B ring. Edges are variable as shown by multiple occultations and occultations of double stars. F ring kittens: 25 features seen in the first 102 occultations show a weak correlation with Prometheus location. We interpret these features as temporary aggregations. Simulation results indicate that accretion must be enhanced to match the kittens' size distribution. Images show that Prometheus triggers the formation of transient objects. Propellers and ghosts: Occulations and images provide evidence for small moonlets in the A, B and C rings. These indicate accretion occurs inside the classical Roche limit. Implications

  3. New Views of Jupiter's Rings

    Science.gov (United States)

    Burns, J. A.

    1998-09-01

    Jupiter's rings are the archetype of ethereal planetary rings (very-low optical-depth bands containing micron-sized "dust"). As a result of much improved observations by Galileo (Ockert-Bell* -- most citations are et al. and Icarus in press* or this meeting) and Keck (de Pater*), we now understand the nature of such rings. The ring has three components: a 104 km-thick toroidal halo (1.4-1.7 RJ; normal optical depth t = 10-6), a thin main ring (1.7-1.8 RJ; t = 10-6), and a pair of exterior gossamer rings (1.8-3.5RJ; t = 10-7). The main ring has patchy ( 20-30 percent) brightness. The ring is reddish and its particles satisfy a -2.5 differential power-law size distribution. Because particle lifetimes are brief, the rings must be continually regenerated, by collisions into parent bodies, which may be unseen or may be the known small ring-moons (Thomas*, Simonelli). The gossamer ring seems to be collisional ejecta derived from the ring-moons Amalthea and Thebe, and evolving inward by Poynting-Robertson drag (Burns). The particles drift through many electromagnetic resonances, clustering around synchronous orbit, which produce jumps in the particles' inclinations (Hamilton). The main ring is probably debris from Adrastea and Metis, which orbit in the equatorial plane. The halo particles are driven vertically by electromagnetic forces, which may be resonant (Schaffer & Burns) or not (Horanyi & Cravens). When halo orbits become highly distorted, particles are lost into Jupiter. Similar faint rings may be attendant to all small, close-in satellites (Showalter).

  4. Tree Rings: Timekeepers of the Past.

    Science.gov (United States)

    Phipps, R. L.; McGowan, J.

    One of a series of general interest publications on science issues, this booklet describes the uses of tree rings in historical and biological recordkeeping. Separate sections cover the following topics: dating of tree rings, dating with tree rings, tree ring formation, tree ring identification, sample collections, tree ring cross dating, tree…

  5. The Rings Characterized by Minimal Left Ideals

    Institute of Scientific and Technical Information of China (English)

    Jun Chao WEI

    2005-01-01

    We study these rings with every minimal left ideal being a projective, direct summand and a p-injective module, respectively. Some characterizations of these rings are given, and the relations among them are obtained. With these rings, we characterize semisimple rings. Finally, we introduce MC2 rings, and give some characterizations of MC2 rings.

  6. RING E3 ligases

    DEFF Research Database (Denmark)

    Cho, Seok Keun; Ryu, Moon Young; Kim, Jong Hum

    2017-01-01

    response pathways of plants through various molecular and genetic studies. In particular, it was recently discovered that ubiquitin proteasome system (UPS), a regulatory mechanism for protein turn over, is greatly involved in the stress responsive pathways. In the UPS, many E3 ligases play key roles...... in recognizing and tethering poly-ubiquitins on target proteins for subsequent degradation by the 26S proteasome. Here we discuss the roles of RING ligases that have been defined in related to abiotic stress responses in plants....

  7. Basic Stand Alone Carrier Line Items PUF

    Data.gov (United States)

    U.S. Department of Health & Human Services — This release contains the Basic Stand Alone (BSA) Carrier Line Items Public Use Files (PUF) with information from Medicare Carrier claims. The CMS BSA Carrier Line...

  8. Fusion Rings for Quantum Groups

    DEFF Research Database (Denmark)

    2014-01-01

    We study the fusion rings of tilting modules for a quantum group at a root of unity modulo the tensor ideal of negligible tilting modules. We identify them in type A with the combinatorial rings from Korff, C., Stroppel, C.: The sl(ˆn)k-WZNW fusion ring: a combinato-rial construction and a realis......We study the fusion rings of tilting modules for a quantum group at a root of unity modulo the tensor ideal of negligible tilting modules. We identify them in type A with the combinatorial rings from Korff, C., Stroppel, C.: The sl(ˆn)k-WZNW fusion ring: a combinato-rial construction...... and a realisation as quotient of quantum cohomology. Adv. Math. 225(1), 200–268, (2010) and give a similar description of the sp2n-fusion ring in terms of non-commutative symmetric functions. Moreover we give a presentation of all fusion rings in classical types as quotients of polynomial rings. Finally we also...... compute the fusion rings for type G2....

  9. Viscosity of ring polymer melts

    KAUST Repository

    Pasquino, Rossana

    2013-10-15

    We have measured the linear rheology of critically purified ring polyisoprenes, polystyrenes, and polyethyleneoxides of different molar masses. The ratio of the zero-shear viscosities of linear polymer melts η0,linear to their ring counterparts η0,ring at isofrictional conditions is discussed as a function of the number of entanglements Z. In the unentangled regime η0,linear/η 0,ring is virtually constant, consistent with the earlier data, atomistic simulations, and the theoretical expectation η0,linear/ η0,ring = 2. In the entanglement regime, the Z-dependence of ring viscosity is much weaker than that of linear polymers, in qualitative agreement with predictions from scaling theory and simulations. The power-law extracted from the available experimental data in the rather limited range 1 < Z < 20, η0,linear/η0,ring ∼ Z 1.2±0.3, is weaker than the scaling prediction (η0,linear/η0,ring ∼ Z 1.6±0.3) and the simulations (η0,linear/ η0,ring ∼ Z2.0±0.3). Nevertheless, the present collection of state-of-the-art experimental data unambiguously demonstrates that rings exhibit a universal trend clearly departing from that of their linear counterparts, and hence it represents a major step toward resolving a 30-year-old problem. © 2013 American Chemical Society.

  10. Influence of Ring Oxidation-Induced Stack Faults on Efficiency in Silicon Solar Cells

    Institute of Scientific and Technical Information of China (English)

    ZHOU Chun-Lan; WANG Wen-Jing; LI Hai-Ling; ZHAO Lei; DIAO Hong-Wei; LI Xu-Dong

    2008-01-01

    @@ We observe a strong correlation between the ring oxidation-induced stack faults (OISF) formed in the course of phosphor diffusion and the efficiency of Czochralski-grown silicon solar cells. The main reason for ring-OISF formation and growth in substrate is the silicon oxidation and phosphorus diffusion process induced silicon self-interstitial point defect during POCl3 diffusion. The decreasing of minority carrier diffusion length in crystal silicon solar cell induced by ring-OISF defects is identified to be one of the major causes of efficiency loss.

  11. SABIC Innovative Plastics: Be the World Best Plastic Resin Manufacturer

    Institute of Scientific and Technical Information of China (English)

    Jenny Du

    2007-01-01

    @@ "SABIC Innovative Plastics is a global supplier of plastic resins, manufacturing and compounding polycarbonate, ABS, SAN, ASA, PPE, PC/ABS, PBT and PEI resins, as well as the LNP* line of high performance specialty compounds," said Hiroshi Yoshida, the Global Market Director for Electronics of SABIC Innovative Plastics based in Tokyo at the press conference held by SABIC Innovative Plastics, November 8th 2007, Shanghai.

  12. Content Distribution for Telecom Carriers

    Directory of Open Access Journals (Sweden)

    Ben Falchuk

    2006-08-01

    Full Text Available Distribution of digital content is a key revenue opportunity for telecommunications carriers. As media content moves from analog and physical media-based distribution to digital on-line distribution, a great opportunity exists for carriers to claim their role in the media value chain and grow revenue by enhancing their broadband “all you can eat” high speed Internet access offer to incorporate delivery of a variety of paid content. By offering a distributed peer to peer content delivery capability with authentication, personalization and payment functions, carriers can gain a larger portion of the revenue paid for content both within and beyond their traditional service domains. This paper describes an approach to digital content distribution that leverages existing Intelligent Network infrastructure that many carriers already possess, as well as Web Services.

  13. Buoyant Norbury's vortex rings

    Science.gov (United States)

    Blyth, Mark; Rodriguez-Rodriguez, Javier; Salman, Hayder

    2014-11-01

    Norbury's vortices are a one-parameter family of axisymmetric vortex rings that are exact solutions to the Euler equations. Due to their relative simplicity, they are extensively used to model the behavior of real vortex rings found in experiments and in Nature. In this work, we extend the original formulation of the problem to include buoyancy effects for the case where the fluid that lies within the vortex has a different density to that of the ambient. In this modified formulation, buoyancy effects enter the problem through the baroclinic term of the vorticity equation. This permits an efficient numerical solution of the governing equation of motion in terms of a vortex contour method that tracks the evolution of the boundary of the vortex. Finally, we compare our numerical results with the theoretical analysis of the short-time evolution of a buoyant vortex. Funded by the Spanish Ministry of Economy and Competitiveness through grant DPI2011-28356-C03-02 and by the London Mathematical Society.

  14. Preserving in Plastic.

    Science.gov (United States)

    Wahla, James

    1985-01-01

    Outlines steps for casting insects in permanent molds prepared from commercially available liquid plastic. Also describes dry mountings in glass, acrylic, and petri dishes. The rationale for specimen use, hints for producing quality results, purchasing information, and safety precautions are considered. (DH)

  15. Informative document waste plastics

    NARCIS (Netherlands)

    Nagelhout D; Sein AA; Duvoort GL

    1989-01-01

    This "Informative document waste plastics" forms part of a series of "informative documents waste materials". These documents are conducted by RIVM on the indstruction of the Directorate General for the Environment, Waste Materials Directorate, in behalf of the program of acti

  16. Discrete dislocation plasticity

    NARCIS (Netherlands)

    van der Giessen, E.; Finel, A; Maziere, D; Veron, M

    2003-01-01

    Conventional continuum mechanics models of inelastic deformation processes axe size scale independent. In contrast, there is considerable experimental evidence that plastic flow in crystalline materials is size dependent over length scales of the order of tens of microns and smaller. At present ther

  17. Progress in neural plasticity

    Institute of Scientific and Technical Information of China (English)

    POO; Mu-Ming

    2010-01-01

    One of the properties of the nervous system is the use-dependent plasticity of neural circuits.The structure and function of neural circuits are susceptible to changes induced by prior neuronal activity,as reflected by short-and long-term modifications of synaptic efficacy and neuronal excitability.Regarded as the most attractive cellular mechanism underlying higher cognitive functions such as learning and memory,activity-dependent synaptic plasticity has been in the spotlight of modern neuroscience since 1973 when activity-induced long-term potentiation(LTP) of hippocampal synapses was first discovered.Over the last 10 years,Chinese neuroscientists have made notable contributions to the study of the cellular and molecular mechanisms of synaptic plasticity,as well as of the plasticity beyond synapses,including activity-dependent changes in intrinsic neuronal excitability,dendritic integration functions,neuron-glia signaling,and neural network activity.This work highlight some of these significant findings.

  18. New plastic recycling technology

    Science.gov (United States)

    Greater than 60% of the total plastic content of municipal solid waste is comprised of polyolefins (high-density, low-density, and linear polyethylene and polypropylene. Polyethylene (PE) is the largest-volume component but presents a challenge due to the absence of low-energy de...

  19. Persisting Plastic Addiction

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    The policy on curbing plastic shopping bag use implemented three years ago has produced mixed results In a bustling farmers’market tucked in a narrow street in Xisanqi residential community in north Beijing,stalls selling vegetables,fruits and other foods line the sidewalk.

  20. Ring current and radiation belts

    Science.gov (United States)

    Williams, D. J.

    1987-01-01

    Studies performed during 1983-1986 on the ring current, the injection boundary model, and the radiation belts are discussed. The results of these studies yielded the first observations on the composition and charge state of the ring current throughout the ring-current energy range, and strong observational support for an injection-boundary model accounting for the origins of radiation-belt particles, the ring current, and substorm particles observed at R less than about 7 earth radii. In addition, the results have demonstrated that the detection of energetic neutral atoms generated by charge-exchange interactions between the ring current and the hydrogen geocorona can provide global images of the earth's ring current and its spatial and temporal evolution.

  1. Magnetization of two coupled rings

    Energy Technology Data Exchange (ETDEWEB)

    Avishai, Y [Department of Physics and Ilse Katz Center for Nanotechnology, Ben Gurion University, Beer Sheva 84105 (Israel); Luck, J M [Institut de Physique Theorique, IPhT, CEA Saclay, and URA 2306, CNRS, 91191 Gif-sur-Yvette cedex (France)], E-mail: yshai@bgu.ac.il, E-mail: jean-marc.luck@cea.fr

    2009-05-01

    We investigate the persistent currents and magnetization of a mesoscopic system consisting of two clean metallic rings sharing a single contact point in a magnetic field. Many novel features with respect to the single-ring geometry are underlined, including the explicit dependence of wavefunctions on the Aharonov-Bohm fluxes, the complex pattern of two-fold and three-fold degeneracies, the key role of length and flux commensurability, and in the case of commensurate ring lengths the occurrence of idle levels which do not carry any current. Spin-orbit interactions, induced by the electric fields of charged wires threading the rings, give rise to a peculiar version of the Aharonov-Casher effect where, unlike for a single ring, spin is not conserved. Remarkably enough, this can only be realized when the Aharonov-Bohm fluxes in both rings are neither integer nor half-integer multiples of the flux quantum.

  2. Burnside Rings of Fusion Systems

    DEFF Research Database (Denmark)

    Reeh, Sune Precht

    , and we produce a basis for the Burnside ring that shares properties with the transitive sets for a finite group. We construct a transfer map from the p-local Burnside ring of the underlying p-group S to the p-local Burnside ring of F. Using such transfer maps, we give a new explicit construction...... of Burnside rings given by multiplication with the characteristic idempotent, and we show that this map is the transfer map previously constructed. Applying these results, we show that for every saturated fusion system the ring generated by all (non-idempotent) characteristic elements in the p-local double...... of the characteristic idempotent of F { the unique idempotent in the p-local double Burnside ring of S satisfying properties of Linckelmann and Webb. We describe this idempotent both in terms of fixed points and as a linear combination of transitive bisets. Additionally, using fixed points we determine the map...

  3. Black di-ring and infinite nonuniqueness

    CERN Document Server

    Iguchi, H; Iguchi, Hideo; Mishima, Takashi

    2007-01-01

    We show that the $S^1$-rotating black rings can be superposed by the solution generating technique. We analyze the black di-ring solution for the simplest case of multiple rings. There exists an equilibrium black di-ring where the conical singularities are cured by the suitable choice of physical parameters. Also there are infinite numbers of black di-rings with the same mass and angular momentum. These di-rings can have two different continuous limits of single black rings. Therefore we can transform the fat black ring to the thin ring with the same mass and angular momentum by way of the di-ring solutions.

  4. Saturn's Rings and Associated Ring Plasma Cavity: Evidence for Slow Ring Erosion

    Science.gov (United States)

    Farrell, W. M.; Kurth, W. S.; Gurnett, D. A.; Persoon, A. M.; MacDowall, R. J.

    2017-01-01

    We re-examine the radio and plasma wave observations obtained during the Cassini Saturn orbit insertion period, as the spacecraft flew over the northern ring surface into a radial distance of 1.3 Rs (over the C-ring). Voyager era studies suggest the rings are a source of micro-meteoroid generated plasma and dust, with theorized peak impact-created plasma outflows over the densest portion of the rings (central B-ring). In sharp contrast, the Cassini Radio and Plasma Wave System (RPWS) observations identify the presence of a ring-plasma cavity located in the central portion of the B-ring, with little evidence of impact-related plasma. While previous Voyager era studies have predicted unstable ion orbits over the C- ring, leading to field-aligned plasma transport to Saturns ionosphere, the Cassini RPWS observations do not reveal evidence for such instability-created plasma fountains. Given the passive ring loss processes observed by Cassini, we find that the ring lifetimes should extend >10(exp 9) years, and that there is limited evidence for prompt destruction (loss in <100 Myrs).

  5. ring og refleksion

    DEFF Research Database (Denmark)

    Wahlgren, B.; Rattleff, Pernille; Høyrup, S.

    State of the art inden for forskning om læring på arbejdspladsen samt gennemgang af læringsteori og refleksionsbegrebet hos Dewey, Dreyfus, Schön, Argyris, Kolb, Jarvis, Mezirow og Brookfield. Afsluttes med diskussion af syntetiseret model for læring på arbejdspladsen.......State of the art inden for forskning om læring på arbejdspladsen samt gennemgang af læringsteori og refleksionsbegrebet hos Dewey, Dreyfus, Schön, Argyris, Kolb, Jarvis, Mezirow og Brookfield. Afsluttes med diskussion af syntetiseret model for læring på arbejdspladsen....

  6. Why Are Ring Galaxies Interesting?

    CERN Document Server

    Higdon, James L

    2010-01-01

    Compared with ordinary spirals, the ISM in ring galaxies experiences markedly different physical conditions and evolution. As a result, ring galaxies provide interesting perspectives on the triggering/quenching of large scale star formation and the destructive effects of massive stars on molecular cloud complexes. We use high resolution radio, sub-millimeter, infrared, and optical data to investigate the role of gravitational stability in star formation regulation, factors influencing the ISM's molecular fraction, and evidence of peculiar star formation laws and efficiencies in two highly evolved ring galaxies: Cartwheel and the Lindsay-Shapley ring.

  7. A QSPR for the plasticization efficiency of polyvinylchloride plasticizers.

    Science.gov (United States)

    Chandola, Mridula; Marathe, Sujata

    2008-01-01

    A simple quantitative structure property relationship (QSPR) for correlating the plasticization efficiency of 25 polyvinylchloride (PVC) plasticizers was obtained using molecular modeling. The plasticizers studied were-aromatic esters (phthalate, terephthalate, benzoate, trimellitate), aliphatic esters (adipate, sebacate, azelate), citrates and a phosphate. The low temperature flex point, Tf, of plasticized polyvinylchloride resins was considered as an indicator of plasticization efficiency. Initially, we attempted to predict plasticization efficiency of PVC plasticizers from physical and structural descriptors derived from the plasticizer molecule alone. However, the correlation of these descriptors with Tf was not very good with R=0.78 and r2=0.613. This implied that the selected descriptors were unable to predict all the interactions between PVC and plasticizer. Hence, to account for these interactions, a model containing two polyvinylchloride (PVC) chain segments along with a plasticizer molecule in a simulation box was constructed, using molecular mechanics. A good QSPR equation correlating physical and structural descriptors derived from the model to Tf of the plasticized resins was obtained with R=0.954 and r2=0.909.

  8. On Weakly P.P. Rings

    Institute of Scientific and Technical Information of China (English)

    Xiang Yue-ming; Ouyang Lun-qun; Wang Shu-gui

    2015-01-01

    We introduce, in this paper, the right weakly p.p. rings as the generaliza-tion of right p.p. rings. It is shown that many properties of the right p.p. rings can be extended onto the right weakly p.p. rings. Relative examples are constructed. As applications, we also characterize the regular rings and the semisimple rings in terms of the right weakly p.p. rings.

  9. Numerical simulation and analysis of losses in air-core plastic photonic bandgap fibers

    Institute of Scientific and Technical Information of China (English)

    Tieshan Guan; Mingyang Chen; Zhilong Zhang; Rongjin Yu

    2005-01-01

    @@ The loss properties of air-core plastic photonic bandgap fibers are analyzed by multipole method. Despite the relatively large absorption loss of plastics (PMMA), the contribution of material absorption loss can be reduced significantly through appropriate selection of operating wavelength, number of cladding air-hole rings, radius of air-core, and position of photonic band gap. The transmission loss in this type of fiber can be decreased by an order of magnitude in comparison with that of conventional plastic optical fiber.

  10. PLASTIC ZONES IN AN INFINITELY LONG TRANSVERSELY ISOTROPIC SOLID CYLINDER CONTAINING A RINGSHAPED CRACK

    Directory of Open Access Journals (Sweden)

    Mesut UYANER

    1999-02-01

    Full Text Available In this study, the problem of a ring shaped-crack contained in an infinitely long solid cylinder of elastic perfectly-plastic material is considered. The problem is formulated for a transversely isotropic material by using integral transform technique under uniform load. Due to the geometry of the configuration, Hankel and Fourier integral transform techniques are chosen and the problem is reduced to a singular integral equation. This integral equation is solved numerically by using Gaussian Quadrature Formulae and the values are evaluated for discrete points. The plastic zone lengths are obtained by using the plastic strip model.

  11. Ultra-compact terahertz switch with graphene ring resonators

    Science.gov (United States)

    Sun, Jian-Zhong; Zhang, Le; Gao, Fei

    2016-10-01

    We propose and numerically demonstrate a compact terahertz wave switch which is composed of two graphene waveguides and three graphene ring resonators. Changing the bias voltage of the Fermi level in the center graphene ring, the resonant mode can be tuned when the plasmon waves in the waveguides and rings are coupled. We theoretically explain their mechanisms as being due to bias voltage change induced carrier density of graphene modification and the coupling coefficients of graphene plasmon effect after carrier density change, respectively. The mechanism of such a terahertz wave switch is further theoretically analyzed and numerically investigated with the aid of the finite element method. With an appropriate design, the proposed device offers the opportunity to ‘tune’ the terahertz wave ON-OFF with an ultra-fast, high extinction ratio and compact size. This structure has the potential applications in terahertz wave integrated circuits. Project supported by the Public Technology Research Project of Zhejiang Province, China (Grant No. 2015C31116).

  12. The eRHIC Ring-Ring Collider Design

    CERN Document Server

    Wang, Fuhua; Beebe-Wang, Joanne; Deshpande, Abhay A; Farkhondeh, Manouchehr; Franklin, Wilbur; Graves, William; Litvinenko, Vladimir N; MacKay, William W; Milner, Richard; Montag, Christoph; Ozaki, Satoshi; Parker, Brett; Peggs, Steve; Ptitsyn, Vadim; Roser, Thomas; Tepikian, Steven; Trbojevic, Dejan; Tschalär, C; Wang, Dong; Zolfaghari, Abbasali; Zwart, Townsend; van der Laan, Jan

    2005-01-01

    The eRHIC ring-ring collider is the main design option of the future lepton-ion collider at Brookhaven National Laboratory. We report the revisions of the ring-ring collider design features to the baseline design presented in the eRHIC Zeroth Design Report (ZDR). These revisions have been made during the past year. They include changes of the interaction region which are required from the modifications in the design of the main detector. They also include changes in the lepton storage ring for high current operations as a result of better understandings of beam-beam interaction effects. The updated collider luminosity and beam parameters also take into account a more accurate picture of current and future operational aspects of RHIC.

  13. Sustainable reverse logistics for household plastic waste

    OpenAIRE

    Bing, X

    2014-01-01

    Summary of the thesis titled “Sustainable Reverse Logistics for Household Plastic Waste” PhD Candidate: Xiaoyun Bing Recycled plastic can be used in the manufacturing of plastic products to reduce the use of virgin plastics material. The cost of recycled plastics is usually lower than that of virgin plastics. Therefore, it is environmentally and economically beneficial to improve the plastic recycling system to ensure more plastic waste from households is properly collected and pr...

  14. Plasticity modeling & computation

    CERN Document Server

    Borja, Ronaldo I

    2013-01-01

    There have been many excellent books written on the subject of plastic deformation in solids, but rarely can one find a textbook on this subject. “Plasticity Modeling & Computation” is a textbook written specifically for students who want to learn the theoretical, mathematical, and computational aspects of inelastic deformation in solids. It adopts a simple narrative style that is not mathematically overbearing, and has been written to emulate a professor giving a lecture on this subject inside a classroom. Each section is written to provide a balance between the relevant equations and the explanations behind them. Where relevant, sections end with one or more exercises designed to reinforce the understanding of the “lecture.” Color figures enhance the presentation and make the book very pleasant to read. For professors planning to use this textbook for their classes, the contents are sufficient for Parts A and B that can be taught in sequence over a period of two semesters or quarters.

  15. Bacterial Carriers for Glioblastoma Therapy

    Directory of Open Access Journals (Sweden)

    Nalini Mehta

    2017-03-01

    Full Text Available Treatment of aggressive glioblastoma brain tumors is challenging, largely due to diffusion barriers preventing efficient drug dosing to tumors. To overcome these barriers, bacterial carriers that are actively motile and programmed to migrate and localize to tumor zones were designed. These carriers can induce apoptosis via hypoxia-controlled expression of a tumor suppressor protein p53 and a pro-apoptotic drug, Azurin. In a xenograft model of human glioblastoma in rats, bacterial carrier therapy conferred a significant survival benefit with 19% overall long-term survival of >100 days in treated animals relative to a median survival of 26 days in control untreated animals. Histological and proteomic analyses were performed to elucidate the safety and efficacy of these carriers, showing an absence of systemic toxicity and a restored neural environment in treated responders. In the treated non-responders, proteomic analysis revealed competing mechanisms of pro-apoptotic and drug-resistant activity. This bacterial carrier opens a versatile avenue to overcome diffusion barriers in glioblastoma by virtue of its active motility in extracellular space and can lead to tailored therapies via tumor-specific expression of tumoricidal proteins.

  16. Low-cost carriers fare competition effect

    NARCIS (Netherlands)

    Carmona Benitez, R.B.; Lodewijks, G.

    2010-01-01

    This paper examines the effects that low-cost carriers (LCC’s) produce when entering new routes operated only by full-service carriers (FSC’s) and routes operated by low-cost carriers in competition with full-service carriers. A mathematical model has been developed to determine what routes should b

  17. Low temperature creep plasticity

    Directory of Open Access Journals (Sweden)

    Michael E. Kassner

    2014-07-01

    Full Text Available The creep behavior of crystalline materials at low temperatures (T < 0.3Tm is discussed. In particular, the phenomenological relationships that describe primary creep are reviewed and analyzed. A discussion of the activation energy for creep at T < 0.3Tm is discussed in terms of the context of higher temperature activation energy. The basic mechanism(s of low temperature creep plasticity are discussed, as well.

  18. Clean Elements in Abelian Rings

    Indian Academy of Sciences (India)

    Angelina Y M Chin

    2009-04-01

    Let be a ring with identity. An element in is said to be clean if it is the sum of a unit and an idempotent. is said to be clean if all of its elements are clean. If every idempotent in is central, then is said to be abelian. In this paper we obtain some conditions equivalent to being clean in an abelian ring.

  19. DELPHI's Ring Imaging Cherenkov Chamber

    CERN Multimedia

    1989-01-01

    The hundreds of mirrors around this Ring Imaging Cherenkov Chamber reflect cones of light created by fast moving particles to a detector. The velocity of a particle can be measured by the size of the ring produced on the detector. DELPHI, which ran from 1989 to 2000 on the LEP accelerator, was primarily concerned with particle identification.

  20. Pyrimidine-pyridine ring interconversion

    NARCIS (Netherlands)

    Plas, van der H.C.

    2003-01-01

    This chapter discusses the pyrimidine-to-pyridine ring transformation and pyridine-to-pyrimidine ring transformation. In nucleophile-induced pyrimidine-to-pyridine rearrangements, two types of reactions can be distinguished depending on the structure of the nucleophile: (1) reactions in which the ni

  1. Supercharacter theories and Schur rings

    CERN Document Server

    Hendrickson, Anders O F

    2010-01-01

    Diaconis and Isaacs have defined the supercharacter theories of a finite group to be certain approximations to the ordinary character theory of the group. We make explicit the connection between supercharacter theories and Schur rings, and we provide supercharacter theory constructions which correspond to Schur ring constructions of Leung and Man and of Tamaschke.

  2. Contraceptive vaginal rings: a review.

    Science.gov (United States)

    Brache, Vivian; Faundes, Anibal

    2010-11-01

    Development efforts on contraceptive vaginal rings were initiated over 40 years ago based on two principles: the capacity of the vaginal epithelium to absorb steroids and the capacity of elastomers to release these hormones at a nearly constant rate. Numerous models of contraceptive vaginal rings (CVRs) have been studied, but only two have reached the market: NuvaRing, a combined ring that releases etonogestrel (ENG) and ethinylestradiol (EE), and Progering, a progesterone-releasing ring for use in lactating women. The main advantages of CVRs are their effectiveness (similar to or slightly better than the pill), ease of use without the need of remembering a daily routine, user's ability to control initiation and discontinuation, nearly constant release rate allowing for lower doses, greater bioavailability and good cycle control with the combined ring. The main disadvantages are related to the mode of delivery; CVRs may cause vaginal discharge and complaints, ring expulsion is not uncommon, the ring may be felt during coitus and vaginal insertion may be unpleasant for some women. The studies reviewed in this article provide evidence that CVRs are safe, effective and highly acceptable to women. There is no doubt that CVRs offer a new, effective contraceptive option to women, expanding their available choices of hormonal contraception.

  3. Constructions over localizations of rings

    Directory of Open Access Journals (Sweden)

    Alessandro Logar

    1987-11-01

    Full Text Available In this paper we construct a category of effective noetherian rings in which linear equations can be “solved”. This category is closed with respect to some important constructions like trascendental extensions, quotientations, finite products and localizations with respect to a large class of multiplicatively closed systems. Hence it gives a definition of “constructive” rings.

  4. New perspectives in plastic biodegradation.

    Science.gov (United States)

    Sivan, Alex

    2011-06-01

    During the past 50 years new plastic materials, in various applications, have gradually replaced the traditional metal, wood, leather materials. Ironically, the most preferred property of plastics--durability--exerts also the major environmental threat. Recycling has practically failed to provide a safe solution for disposal of plastic waste (only 5% out of 1 trillion plastic bags, annually produced in the US alone, are being recycled). Since the most utilized plastic is polyethylene (PE; ca. 140 million tons/year), any reduction in the accumulation of PE waste alone would have a major impact on the overall reduction of the plastic waste in the environment. Since PE is considered to be practically inert, efforts were made to isolate unique microorganisms capable of utilizing synthetic polymers. Recent data showed that biodegradation of plastic waste with selected microbial strains became a viable solution. Copyright © 2011 Elsevier Ltd. All rights reserved.

  5. Microelectronics plastic molded packaging

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, D.R. [Ktech Corp., Albuquerque, NM (United States); Palmer, D.W.; Peterson, D.W. [Sandia National Lab., Albuquerque, NM (United States)] [and others

    1997-02-01

    The use of commercial off-the-shelf (COTS) microelectronics for nuclear weapon applications will soon be reality rather than hearsay. The use of COTS for new technologies for uniquely military applications is being driven by the so-called Perry Initiative that requires the U.S. Department of Defense (DoD) to accept and utilize commercial standards for procurement of military systems. Based on this philosophy, coupled with several practical considerations, new weapons systems as well as future upgrades will contain plastic encapsulated microelectronics. However, a conservative Department of Energy (DOE) approach requires lifetime predictive models. Thus, the focus of the current project is on accelerated testing to advance current aging models as well as on the development of the methodology to be used during WR qualification of plastic encapsulated microelectronics. An additional focal point involves achieving awareness of commercial capabilities, materials, and processes. One of the major outcomes of the project has been the definition of proper techniques for handling and evaluation of modern surface mount parts which might be used in future systems. This program is also raising the familiarity level of plastic within the weapons complex, allowing subsystem design rules accommodating COTS to evolve. A two year program plan is presented along with test results and commercial interactions during this first year.

  6. The Search for Ringed Exoplanets

    Science.gov (United States)

    Kohler, Susanna

    2017-04-01

    Are planetary rings as common in our galaxy as they are in our solar system? A new study demonstrates how we might search for ringed exoplanets and then possibly finds one!Saturns Elsewhere?Artists illustration of the super ring system around exoplanet J1407b. This is the only exoplanet weve found with rings, but its not at all like Saturn. [Ron Miller]Our solar system is filled with moons and planetary rings, so it stands to reason that exoplanetary systems should exhibit the same features. But though weve been in the planet-hunting game for decades, weve only found one exoplanet thats surrounded by a ring system. Whats more, that system J1407b has enormous rings that are vastly different from the modest, Saturn-like rings that we might expect to be more commonplace.Have we not discovered ringed exoplanets just because theyre hard to identify? Or is it because theyre not out there? A team of scientists led by Masataka Aizawa (University of Tokyo) has set out to answer this question by conducting a systematic search for rings around long-period planet candidates.The transit light curve of KIC 10403228, shown with three models: the best-fitting planet-only model (blue) and the two best-fitting planet+ring models (green and red). [Aizawa et al. 2017]The Hunt BeginsWhy long-period planets? Rings are expected to be unstable as the planet gets closer to the central star. Whats more, the planet needs to be far enough away from the stars warmth for the icy rings to exist. The authors therefore select from the collection of candidate transiting planets 89 long-period candidates that might be able to host rings.Aizawa and collaborators then fit single-planet models (with no rings) to the light curves of these planets and search for anomalies curves that arent fit well by these standard models. Particularly suspicious characteristics include a long ingress/egress as the planet moves across the face of the star, and asymmetry of the transit shape.After applying a series of

  7. Formation of polar ring galaxies

    CERN Document Server

    Bournaud, F

    2003-01-01

    Polar ring galaxies are peculiar systems in which a gas rich, nearly polar ring surrounds an early-type or elliptical host galaxy. Two formation scenarios for these objects have been proposed: they are thought to form either in major galaxy mergers or by tidal accretion of the polar material from a gas rich donor galaxy. Both scenarios are studied through N-body simulations including gas dynamics and star formation. Constraints on physical parameters are drawn out, in order to determine which scenario is the most likely to occur. Polar ring galaxies from each scenario are compared with observations and we discuss whether the accretion scenario and the merging scenario account for observational properties of polar ring galaxies. The conclusion of this study is that the accretion scenario is both the most likely and the most supported by observations. Even if the merging scenario is rather robust, most polar ring galaxies are shown to be the result of tidal gas accretion events.

  8. Ionization cooling ring for muons

    Directory of Open Access Journals (Sweden)

    R. Palmer

    2005-06-01

    Full Text Available Practical ionization cooling rings could lead to lower cost or improved performance in neutrino factory or muon collider designs. The ring modeled here uses realistic three-dimensional fields. The performance of the ring compares favorably with the linear cooling channel used in the second U.S. Neutrino Factory Study. The normalized 6D emittance of an ideal ring is decreased by a factor of approximately 240, compared with a factor of only 15 for the linear channel. We also examine such real-world effects as windows on the absorbers and rf cavities and leaving empty lattice cells for injection and extraction. For realistic conditions the ring decreases the normalized 6D emittance by a factor of 49.

  9. Studies of methanol maser rings

    CERN Document Server

    Bartkiewicz, A; van Langevelde, H J; De Buizer, J M; Pihlström, Y

    2011-01-01

    We present the results of studies of a new class of 6.7 GHz methanol maser sources with a ring-like emission structure discovered recently with the EVN. We have used the VLA to search for water masers at 22 GHz and radio continuum at 8.4 GHz towards a sample of high-mass star forming regions showing a ring-like distribution of methanol maser spots. Using the Gemini telescopes we found mid-infrared (MIR) counterparts of five methanol rings with a resolution of 0."15. The centres of methanol maser rings are located within, typically, only 0."2 of the MIR emission peak, implying their physical relation with a central star. These results strongly support a scenario wherein the ring-like structures appear at the very early stage of massive star formation before either water-maser outflows or H II regions are seen.

  10. A Note on Clean Rings

    Institute of Scientific and Technical Information of China (English)

    Zhou Wang; Jianlong Chen

    2007-01-01

    Let R be a ring and g(x) a polynomial in C[x],where C=C(R) denotes the center of R.Camillo and Sim6n called the ring g(x)-clean if every element of R can be written as the sum of a unit and a root of g(x).In this paper,we prove that for a,b (E) C,the ring R is clean and b - a is invertible in R if and only if R is g1(x)-clean,where gl(x) = (x - a)(x - b).This implies that in some sense the notion of g(x)-clean rings in the Nicholson-Zhou Theorem and in the Camillo-Sim6n Theorem is indeed equivalent to the notion of clean rings.

  11. Interfacial interactions between plastic particles in plastics flotation.

    Science.gov (United States)

    Wang, Chong-qing; Wang, Hui; Gu, Guo-hua; Fu, Jian-gang; Lin, Qing-quan; Liu, You-nian

    2015-12-01

    Plastics flotation used for recycling of plastic wastes receives increasing attention for its industrial application. In order to study the mechanism of plastics flotation, the interfacial interactions between plastic particles in flotation system were investigated through calculation of Lifshitz-van der Waals (LW) function, Lewis acid-base (AB) Gibbs function, and the extended Derjaguin-Landau-Verwey-Overbeek potential energy profiles. The results showed that van der Waals force between plastic particles is attraction force in flotation system. The large hydrophobic attraction, caused by the AB Gibbs function, is the dominant interparticle force. Wetting agents present significant effects on the interfacial interactions between plastic particles. It is found that adsorption of wetting agents promotes dispersion of plastic particles and decreases the floatability. Pneumatic flotation may improve the recovery and purity of separated plastics through selective adsorption of wetting agents on plastic surface. The relationships between hydrophobic attraction and surface properties were also examined. It is revealed that there exists a three-order polynomial relationship between the AB Gibbs function and Lewis base component. Our finding provides some insights into mechanism of plastics flotation.

  12. Effect of sizes of forming rolls on cold ring rolling by 3D-FE numerical simulation

    Institute of Scientific and Technical Information of China (English)

    GUO Liang-gang; YANG He

    2006-01-01

    During cold ring rolling process,changing the sizes of forming rolls including driver roll and idle roll will lead to a change of amount of feed △h and contact areas between ring blank and forming rolls,thus a change of the shape and dimension of deformation zone located in the gap of forming rolls is found. It has a significant effect on metal flow and the forming quality of deformed ring. So the size effect of forming rolls on cold ring rolling was investigated by three-dimensional dynamic explicit FEM under ABAQUS environment. The obtained results thoroughly reveal the influence laws of the sizes of forming rolls on the average spread,fishtail coefficient,degree of inhomogeneous deformation and force and power parameters etc not only provide an important basis for design of the forming rolls and optimization of cold ring rolling process,but also reveal the plastic deformation mechanism of cold ring rolling.

  13. A Fully-Coupled Approach for Modelling Plastic Deformation and Liquid Lubrication in Metal Forming

    DEFF Research Database (Denmark)

    Üstünyagiz, Esmeray; Christiansen, Peter; Nielsen, Chris V.;

    2016-01-01

    This paper presents a new approach for combined modelling of plastic deformation andliquid lubrication in the contact interfaces between material and tooling in metal forming includingsituations where the lubricant is functioning as a pressure carrier. The approach is an alternative toconventiona...... and numerical fundamentals of the proposedapproach and includes selected examples in order to illustrate its advantages and limitations....

  14. Black Hole Ringing, Quasinormal Modes, and Light Rings

    CERN Document Server

    Khanna, Gaurav

    2016-01-01

    Modelling of gravitational waves from binary black hole inspiral has played an important role in the recent observations of such signals. The late-stage ringdown phase of the gravitational waveform is often associated with the null particle orbit (\\light ring") of the black hole spacetime. With simple models we show that this link between the light ring and spacetime ringing is based more on the history of applications than on an actual constraining relationship. We also show, in particular, that a better understanding of the disassociation between the two, may be relevant to the astrophysically interesting case of rotating (Kerr) black holes.

  15. Is the bell ringing?

    CERN Multimedia

    Francesco Poppi

    2010-01-01

    During the Nobel prize-winning UA1 experiment, scientists in the control room used to ring a bell if a particularly interesting event had occurred. Today, the “CMS Exotica hotline” routine produces a daily report that lists the exotic events that were recorded the day before.   Display of an event selected by the Exotica routine. Take just a very small fraction of the available data (max. 5%); define the events that you want to keep and set the parameters accordingly; run the Exotica routine and only look at the very few images that the system has selected for you. This is the recipe that a small team of CMS researchers has developed to identify the signals coming from possible new physics processes. “This approach does not replace the accurate data analysis on the whole set of data. However, it is a very fast and effective way to focus on just a few events that are potentially very interesting”, explains Maurizio Pierini (CERN), who developed the...

  16. 75 FR 2923 - Motor Carrier Safety Advisory Committee Public Meeting

    Science.gov (United States)

    2010-01-19

    ... Federal Motor Carrier Safety Administration Motor Carrier Safety Advisory Committee Public Meeting AGENCY: Federal Motor Carrier Safety Administration (FMCSA), DOT. ACTION: Notice of Motor Carrier Safety Advisory Committee Meeting. SUMMARY: FMCSA announces that its Motor Carrier Safety Advisory Committee (MCSAC)...

  17. 75 FR 72863 - Motor Carrier Safety Advisory Committee Public Meeting

    Science.gov (United States)

    2010-11-26

    ... Federal Motor Carrier Safety Administration Motor Carrier Safety Advisory Committee Public Meeting AGENCY: Federal Motor Carrier Safety Administration, DOT. ACTION: Notice of Motor Carrier Safety Advisory Committee Meeting. SUMMARY: FMCSA announces that the Agency's Motor Carrier Safety Advisory Committee...

  18. 76 FR 12214 - Motor Carrier Safety Advisory Committee Public Meeting

    Science.gov (United States)

    2011-03-04

    ... Federal Motor Carrier Safety Administration Motor Carrier Safety Advisory Committee Public Meeting AGENCY: Federal Motor Carrier Safety Administration, DOT. ACTION: Notice: Announcement of Motor Carrier Safety Advisory Committee meeting; request for comment. SUMMARY: The Federal Motor Carrier Safety...

  19. 75 FR 29384 - Motor Carrier Safety Advisory Committee Public Meeting

    Science.gov (United States)

    2010-05-25

    ... Federal Motor Carrier Safety Administration Motor Carrier Safety Advisory Committee Public Meeting AGENCY: Federal Motor Carrier Safety Administration (FMCSA), DOT. ACTION: Notice of Motor Carrier Safety Advisory Committee meeting. SUMMARY: FMCSA announces that its Motor Carrier Safety Advisory Committee (MCSAC)...

  20. Use of recycled plastics in wood plastic composites - a review.

    Science.gov (United States)

    Kazemi Najafi, Saeed

    2013-09-01

    The use of recycled and waste thermoplastics has been recently considered for producing wood plastic composites (WPCs). They have great potential for WPCs manufacturing according to results of some limited researches. This paper presents a detailed review about some essential properties of waste and recycled plastics, important for WPCs production, and of research published on the effect of recycled plastics on the physical and mechanical properties of WPCs.

  1. Failure analysis of wear of main clutch separating ring of heavy vehicles

    Institute of Scientific and Technical Information of China (English)

    SUN Xiao-long; LI Xiao-yan; ZHU You-li; XU Bin-shi

    2005-01-01

    The severe wear of separating ring is considered to be a main reason which leads to the improper declutch of the main clutch of heavy vehicles. The wear mechanism of the separating ring is not well understood. Scanning electron microscopy and transmission electron microscopy were employed to analyze the surface features and dislocation characteristics of the separating ring. The typical features of furrows and rolled tongue-like metal were found on the surface of separating ring by scanning electron microscopy observation, which can be considered as a major indi cation of the grain-abrasion. A zone of high density dislocation was noted on the subsurface of the separating ring by transmission electron microscopy observation, which implies the contribution of the severe impact on the surface of the separating ring in the wear process. The influences of the structure of the separating ring, the service condition and the in-service stress distribution on the wear behavior, were also analyzed. The results show that the failure of separating ring results from the impact wear and grain-abrasion together with the plastic deformation.

  2. Ion Rings for Magnetic Fusion

    Energy Technology Data Exchange (ETDEWEB)

    Greenly, John, B.

    2005-07-31

    This Final Technical Report presents the results of the program, Ion Rings for Magnetic Fusion, which was carried out under Department of Energy funding during the period August, 1993 to January, 2005. The central objective of the program was to study the properties of field-reversed configurations formed by ion rings. In order to reach this objective, our experimental program, called the Field-reversed Ion Ring Experiment, FIREX, undertook to develop an efficient, economical technology for the production of field-reversed ion rings. A field-reversed configuration (FRC) in which the azimuthal (field-reversing) current is carried by ions with gyro-radius comparable to the magnetic separatrix radius is called a field-reversed ion ring. A background plasma is required for charge neutralization of the ring, and this plasma will be confined within the ring's closed magnetic flux. Ion rings have long been of interest as the basis of compact magnetic fusion reactors, as the basis for a high-power accelerator for an inertial fusion driver, and for other applications of high power ion beams or plasmas of high energy density. Specifically, the FIREX program was intended to address the longstanding question of the contribution of large-orbit ions to the observed stability of experimental FRCs to the MHD tilt mode. Typical experimental FRCs with s {approx} 2-4, where s is the ratio of separatrix radius to ion gyro-radius, have been stable to tilting, but desired values for a fusion reactor, s > 20, should be unstable. The FIREX ring would consist of a plasma with large s for the background ions, but with s {approx} 1 for the ring ions. By varying the proportions of these two populations, the minimum proportion of large-orbit ions necessary for stability could be determined. The incorporation of large-orbit ions, perhaps by neutral-beam injection, into an FRC has been advanced for the purpose of stabilizing, heating, controlling angular momentum, and aiding the formation

  3. Ideals in Morita Rings and Morita Semigroups

    Institute of Scientific and Technical Information of China (English)

    Yu Qun CHEN; Yun FAN; Zhi Feng HAO

    2005-01-01

    We characterize the lattice of all ideals of a Morita ring (semigroup) when the corresponding pair of rings (semigroups) in the Morita context are Morita equivalent s-unital (like-unity) rings(semigroups).

  4. Hydrocarbon Emission Rings in Protoplanetary Disks Induced by Dust Evolution

    Science.gov (United States)

    Bergin, Edwin A.; Du, Fujun; Cleeves, L. Ilsedore; Blake, G. A.; Schwarz, K.; Visser, R.; Zhang, K.

    2016-11-01

    We report observations of resolved C2H emission rings within the gas-rich protoplanetary disks of TW Hya and DM Tau using the Atacama Large Millimeter Array. In each case the emission ring is found to arise at the edge of the observable disk of millimeter-sized grains (pebbles) traced by submillimeter-wave continuum emission. In addition, we detect a C3H2 emission ring with an identical spatial distribution to C2H in the TW Hya disk. This suggests that these are hydrocarbon rings (i.e., not limited to C2H). Using a detailed thermo-chemical model we show that reproducing the emission from C2H requires a strong UV field and C/O > 1 in the upper disk atmosphere and outer disk, beyond the edge of the pebble disk. This naturally arises in a disk where the ice-coated dust mass is spatially stratified due to the combined effects of coagulation, gravitational settling and drift. This stratification causes the disk surface and outer disk to have a greater permeability to UV photons. Furthermore the concentration of ices that transport key volatile carriers of oxygen and carbon in the midplane, along with photochemical erosion of CO, leads to an elemental C/O ratio that exceeds unity in the UV-dominated disk. Thus the motions of the grains, and not the gas, lead to a rich hydrocarbon chemistry in disk surface layers and in the outer disk midplane.

  5. Direct liquefaction of plastics and coprocessing of coal with plastics

    Energy Technology Data Exchange (ETDEWEB)

    Huffman, G.P.; Feng, Z.; Mahajan, V. [Univ. of Kentucky, Lexington, KY (United States)

    1995-12-31

    The objectives of this work were to optimize reaction conditions for the direct liquefaction of waste plastics and the coprocessing of coal with waste plastics. In previous work, the direct liquefaction of medium and high density polyethylene (PE), polypropylene (PPE), poly(ethylene terephthalate) (PET), and a mixed plastic waste, and the coliquefaction of these plastics with coals of three different ranks was studied. The results established that a solid acid catalyst (HZSM-5 zeolite) was highly active for the liquefaction of the plastics alone, typically giving oil yields of 80-95% and total conversions of 90-100% at temperatures of 430-450 {degrees}C. In the coliquefaction experiments, 50:50 mixtures of plastic and coal were used with a tetralin solvent (tetralin:solid = 3:2). Using approximately 1% of the HZSM-5 catalyst and a nanoscale iron catalyst, oil yields of 50-70% and total conversion of 80-90% were typical. In the current year, further investigations were conducted of the liquefaction of PE, PPE, and a commingled waste plastic obtained from the American Plastics Council (APC), and the coprocessing of PE, PPE and the APC plastic with Black Thunder subbituminous coal. Several different catalysts were used in these studies.

  6. Plastic Surgery and Suicide: A Clinical Guide for Plastic Surgeons.

    Science.gov (United States)

    Reddy, Vikram; Coffey, M Justin

    2016-08-01

    Several studies have identified an increased risk of suicide among patient populations which a plastic surgeon may have a high risk of encountering: women undergoing breast augmentation, cosmetic surgery patients, and breast cancer patients. No formal guidelines exist to assist a plastic surgeon when faced with such a patient, and not every plastic surgery team has mental health clinicians that are readily accessible for consultation or referral. The goal of this clinical guide is to offer plastic surgeons a set of practical approaches to manage potentially suicidal patients. In addition, the authors review a screening tool, which can assist surgeons when encountering high-risk patients.

  7. Ring-Ringlet Interactions in Saturn's C Ring

    Science.gov (United States)

    Rappaport, N. J.

    1997-01-01

    The overall obejective of this work is to derive a theoretical model for the formation of gaps harboring isolated ringlets in order to explain the presence of such features in Saturn's C ring and Cassini division.

  8. ISS qualified thermal carrier equipment

    Science.gov (United States)

    Deuser, Mark S.; Vellinger, John C.; Jennings, Wm. M.

    2000-01-01

    Biotechnology is undergoing a period of rapid and sustained growth, a trend which is expected to continue as the general population ages and as new medical treatments and products are conceived. As pharmaceutical and biomedical companies continue to search for improved methods of production and, for answers to basic research questions, they will seek out new avenues of research. Space processing on the International Space Station (ISS) offers such an opportunity! Space is rapidly becoming an industrial laboratory for biotechnology research and processing. Space bioprocessing offers exciting possibilities for developing new pharmaceuticals and medical treatments, which can be used to benefit mankind on Earth. It also represents a new economic frontier for the private sector. For over eight years, the thermal carrier development team at SHOT has been working with government and commercial sector scientists who are conducting microgravity experiments that require thermal control. SHOT realized several years ago that the hardware currently being used for microgravity thermal control was becoming obsolete. It is likely that the government, academic, and industrial bioscience community members could utilize SHOT's hardware as a replacement to their current microgravity thermal carrier equipment. Moreover, SHOT is aware of several international scientists interested in utilizing our space qualified thermal carrier. SHOT's economic financing concept could be extremely beneficial to the international participant, while providing a source of geographic return for their particular region. Beginning in 2000, flight qualified thermal carriers are expected to be available to both the private and government sectors. .

  9. Soft Congruence Relations over Rings

    Directory of Open Access Journals (Sweden)

    Xiaolong Xin

    2014-01-01

    Full Text Available Molodtsov introduced the concept of soft sets, which can be seen as a new mathematical tool for dealing with uncertainty. In this paper, we initiate the study of soft congruence relations by using the soft set theory. The notions of soft quotient rings, generalized soft ideals and generalized soft quotient rings, are introduced, and several related properties are investigated. Also, we obtain a one-to-one correspondence between soft congruence relations and idealistic soft rings and a one-to-one correspondence between soft congruence relations and soft ideals. In particular, the first, second, and third soft isomorphism theorems are established, respectively.

  10. Soft congruence relations over rings.

    Science.gov (United States)

    Xin, Xiaolong; Li, Wenting

    2014-01-01

    Molodtsov introduced the concept of soft sets, which can be seen as a new mathematical tool for dealing with uncertainty. In this paper, we initiate the study of soft congruence relations by using the soft set theory. The notions of soft quotient rings, generalized soft ideals and generalized soft quotient rings, are introduced, and several related properties are investigated. Also, we obtain a one-to-one correspondence between soft congruence relations and idealistic soft rings and a one-to-one correspondence between soft congruence relations and soft ideals. In particular, the first, second, and third soft isomorphism theorems are established, respectively.

  11. Hot carrier degradation in semiconductor devices

    CERN Document Server

    2015-01-01

    This book provides readers with a variety of tools to address the challenges posed by hot carrier degradation, one of today’s most complicated reliability issues in semiconductor devices.  Coverage includes an explanation of carrier transport within devices and book-keeping of how they acquire energy (“become hot”), interaction of an ensemble of colder and hotter carriers with defect precursors, which eventually leads to the creation of a defect, and a description of how these defects interact with the device, degrading its performance. • Describes the intricacies of hot carrier degradation in modern semiconductor technologies; • Covers the entire hot carrier degradation phenomenon, including topics such as characterization, carrier transport, carrier-defect interaction, technological impact, circuit impact, etc.; • Enables detailed understanding of carrier transport, interaction of the carrier ensemble with the defect precursors, and an accurate assessment of how the newly created defects imp...

  12. Tree plastic bark

    OpenAIRE

    Casado Arroyo, Carlos

    2016-01-01

    “Tree plastic bark" consiste en la realización de una intervención artística en un entorno natural concreto, generando de esta manera un Site Specific(1). Como hace alusión Rosalind Krauss en sus reflexiones “La escultura en el campo expandido”(2), comenta que su origen esta claramente ligado con el concepto de monumentalidad. La escultura es un monumento, se crea para conmemorar algún hecho o personaje relevante y está realizada para una ubicación concreta. La investigación parte de la id...

  13. Fabrication of plastic biochips

    Energy Technology Data Exchange (ETDEWEB)

    Saaem, Ishtiaq; Ma, Kuo-Sheng; Alam, S. Munir; Tian Jingdong [Department of Biomedical Engineering and Institute for Genome Sciences and Policy, Duke University, Durham, North Carolina 27708 (United States); Department of Medicine and Human Vaccine Institute, Duke University, Durham, North Carolina 27708 (United States); Department of Biomedical Engineering and Institute for Genome Sciences and Policy, Duke University, Durham, North Carolina 27708 (United States)

    2010-07-15

    A versatile surface functionalization procedure based on rf magnetron sputtering of silica was performed on poly(methylmethacrylate), polycarbonate, polypropylene, and cyclic olefin copolymers (Topas 6015). The hybrid thermoplastic surfaces were characterized by x-ray photoelectron spectrometer analysis and contact angle measurements. The authors then used these hybrid materials to perform a sandwich assay targeting an HIV-1 antibody using fluorescent detection and biotinylated peptides immobilized using the bioaffinity of biotin-neutravidin. They found a limit of detection similar to arrays on glass surfaces and believed that this plastic biochip platform may be used for the development of disposable immunosensing and diagnostic applications.

  14. Plastic food packaging and health

    Directory of Open Access Journals (Sweden)

    Raika Durusoy

    2011-02-01

    Full Text Available Plastics have a wide usage in our daily lives. One of their uses is for food packaging and food containers. The aim of this review is to introduce different types of chemicals that can leach from food packaging plastics into foods and cause human exposure and to mention their effects on health. The types of plastics were reviewed under the 13 headings in Turkish Codex Alimentarius and plastics recycling symbols were provided to enable the recognition of the type of plastic when applicable. Chemicals used during the production and that can cause health risks are investigated under the heading of the relevant type of plastic. The most important chemicals from plastic food packaging that can cause toxicity are styrene, 1,3-butadiene, melamine, formaldehyde, acrylamide, di-2-ethylhexyl phthalate, di-2-ethylhexyl adipate, vinyl chloride and bisphenol A. These chemicals have endocrine disrupting, carcinogenic and/or development disrupting effects. These chemicals may leach into foods depending on the chemical properties of the plastic or food, temperature during packaging, processing and storage, exposure to UV and duration of storage. Contact with fatty/oily or acidic foods, heating of the food inside the container, or drinking hot drinks from plastic cups, use of old and scratched plastics and some detergents increase the risk of leaching. The use of plastic containers and packaging for food and beveradges should be avoided whenever possible and when necessary, less harmful types of plastic should be preferred. [TAF Prev Med Bull 2011; 10(1.000: 87-96

  15. The commercialization of plastic surgery.

    Science.gov (United States)

    Swanson, Eric

    2013-09-01

    The last decade has brought a major challenge to the traditional practice of plastic surgery from corporations that treat plastic surgery as a commercial product and market directly to the public. This corporate medicine model may include promotion of a trademarked procedure or device, national advertising that promises stunning results, sales consultants, and claims of innovation, superiority, and improved safety. This article explores the ethics of this business practice and whether corporate medicine is a desirable model for patients and plastic surgeons.

  16. Multiscale modeling and synaptic plasticity.

    Science.gov (United States)

    Bhalla, Upinder S

    2014-01-01

    Synaptic plasticity is a major convergence point for theory and computation, and the process of plasticity engages physiology, cell, and molecular biology. In its many manifestations, plasticity is at the hub of basic neuroscience questions about memory and development, as well as more medically themed questions of neural damage and recovery. As an important cellular locus of memory, synaptic plasticity has received a huge amount of experimental and theoretical attention. If computational models have tended to pick specific aspects of plasticity, such as STDP, and reduce them to an equation, some experimental studies are equally guilty of oversimplification each time they identify a new molecule and declare it to be the last word in plasticity and learning. Multiscale modeling begins with the acknowledgment that synaptic function spans many levels of signaling, and these are so tightly coupled that we risk losing essential features of plasticity if we focus exclusively on any one level. Despite the technical challenges and gaps in data for model specification, an increasing number of multiscale modeling studies have taken on key questions in plasticity. These have provided new insights, but importantly, they have opened new avenues for questioning. This review discusses a wide range of multiscale models in plasticity, including their technical landscape and their implications.

  17. Plastics recycling: challenges and opportunities

    National Research Council Canada - National Science Library

    Jefferson Hopewell; Robert Dvorak; Edward Kosior

    2009-01-01

    .... Advances in technologies and systems for the collection, sorting and reprocessing of recyclable plastics are creating new opportunities for recycling, and with the combined actions of the public...

  18. Americium behaviour in plastic vessels

    Energy Technology Data Exchange (ETDEWEB)

    Legarda, F.; Herranz, M. [Departamento de Ingenieria Nuclear y Mecanica de Fluidos, Escuela Tecnica Superior de Ingenieria de Bilbao, Universidad del Pais Vasco (UPV/EHU), Alameda de Urquijo s/n, 48013 Bilbao (Spain); Idoeta, R., E-mail: raquel.idoeta@ehu.e [Departamento de Ingenieria Nuclear y Mecanica de Fluidos, Escuela Tecnica Superior de Ingenieria de Bilbao, Universidad del Pais Vasco (UPV/EHU), Alameda de Urquijo s/n, 48013 Bilbao (Spain); Abelairas, A. [Departamento de Ingenieria Nuclear y Mecanica de Fluidos, Escuela Tecnica Superior de Ingenieria de Bilbao, Universidad del Pais Vasco (UPV/EHU), Alameda de Urquijo s/n, 48013 Bilbao (Spain)

    2010-07-15

    The adsorption of {sup 241}Am dissolved in water in different plastic storage vessels was determined. Three different plastics were investigated with natural and distilled waters and the retention of {sup 241}Am by these plastics was studied. The same was done by varying vessel agitation time, vessel agitation speed, surface/volume ratio of water in the vessels and water pH. Adsorptions were measured to be between 0% and 70%. The adsorption of {sup 241}Am is minimized with no water agitation, with PET or PVC plastics, and by water acidification.

  19. Vibration insensitive optical ring cavity

    Institute of Scientific and Technical Information of China (English)

    Miao Jin; Jiang Yan-Yi; Fang Su; Bi Zhi-Yi; Ma Long-Sheng

    2009-01-01

    The mounting configuration of an optical ring cavity is optimized for vibration insensitivity by finite element analysis. A minimum response to vertical accelerations is found by simulations made for different supporting positions.

  20. Autumn study on storage rings

    CERN Multimedia

    1974-01-01

    The first two weeks of October have seen storage ring people from accelerator Laboratories throughout the world at CERN to study the fundamental problems of very high energy protonproton colliding beam machines.

  1. Ring Model for Pneumatic Tires

    Institute of Scientific and Technical Information of China (English)

    危银涛; 范成建; 管迪华

    2002-01-01

    This paper reviews the state-of-the-art of the ring modeling method for tires, emphasizing the differences among the various tire ring models. A general tire ring model was then developed including all the nonlinear terms in the ring strain and the initial stresses induced by the internal pressure and rotation. The general equations of motion were derived from the Hamilton principle whth the geometric parameters for the model directly obtained from the tire design. The physical parameters were calculated from experimental mode parameters. A numerical example is given for a 195/70 R14-type tire. The analysis shows that the predicted natural frequencies and the tire mode shape agree well with experimental results.

  2. Perturbations of vortex ring pairs

    CERN Document Server

    Gubser, Steven S; Parikh, Sarthak

    2015-01-01

    We study pairs of co-axial vortex rings starting from the action for a classical bosonic string in a three-form background. We complete earlier work on the phase diagram of classical orbits by explicitly considering the case where the circulations of the two vortex rings are equal and opposite. We then go on to study perturbations, focusing on cases where the relevant four-dimensional transfer matrix splits into two-dimensional blocks. When the circulations of the rings have the same sign, instabilities are mostly limited to wavelengths smaller than a dynamically generated length scale at which single-ring instabilities occur. When the circulations have the opposite sign, larger wavelength instabilities can occur.

  3. [Erythropoietin in plastic surgery].

    Science.gov (United States)

    Günter, C I; Rezaeian, F; Harder, Y; Lohmeyer, J A; Egert, S; Bader, A; Schilling, A F; Machens, H-G

    2013-04-01

    EPO is an autologous hormone, which is known to regulate erythropoiesis. For 30 years it has been used for the therapy of diverse forms of anaemia, such as renal anaemia, tumour-related anaemias, etc. Meanwhile, a multitude of scientific publications were able to demonstrate its pro-regenerative effects after trauma. These include short-term effects such as the inhibition of the "primary injury response" or apoptosis, and mid- and long-term effects for example the stimulation of stem cell recruitment, growth factor production, angiogenesis and re-epithelialisation. Known adverse reactions are increases of thromboembolic events and blood pressure, as well as a higher mortality in patients with tumour anaemias treated with EPO. Scientific investigations of EPO in the field of plastic surgery included: free and local flaps, nerve regeneration, wound healing enhancement after dermal thermal injuries and in chronic wounds.Acute evidence for the clinical use of EPO in the field of plastic surgery is still not satisfactory, due to the insufficient number of Good Clinical Practice (GCP)-conform clinical trials. Thus, the initiation of more scientifically sound trials is indicated.

  4. Optogenetics and synaptic plasticity.

    Science.gov (United States)

    Xie, Yu-feng; Jackson, Michael F; Macdonald, John F

    2013-11-01

    The intricate and complex interaction between different populations of neurons in the brain has imposed limits on our ability to gain detailed understanding of synaptic transmission and its integration when employing classical electrophysiological approaches. Indeed, electrical field stimulation delivered via traditional microelectrodes does not permit the targeted, precise and selective control of neuronal activity amongst a varied population of neurons and their inputs (eg, cholinergic, dopaminergic or glutamatergic neurons). Recently established optogenetic techniques overcome these limitations allowing precise control of the target neuron populations, which is essential for the elucidation of the neural substrates underlying complex animal behaviors. Indeed, by introducing light-activated channels (ie, microbial opsin genes) into specific neuronal populations, optogenetics enables non-invasive optical control of specific neurons with milliseconds precision. These approaches can readily be applied to freely behaving live animals. Recently there is increased interests in utilizing optogenetics tools to understand synaptic plasticity and learning/memory. Here, we summarize recent progress in applying optogenetics in in the study of synaptic plasticity.

  5. Synlig læring

    DEFF Research Database (Denmark)

    Brandsen, Mads

    2017-01-01

    Introduktionen af John Hatties synlig læring i den danske skoleverden møder stadig meget kritik. Mange lærere og pædagoger oplever synlig læring som en tornado, der vil opsuge og ødelægge deres særlige danske udgave af den kontinentale dannelsestænkning, didaktik og pædagogik. Spørgsmålet er om...

  6. Commuting Π-regular rings

    Directory of Open Access Journals (Sweden)

    Shervin Sahebi

    2014-05-01

    Full Text Available ‎$R$ is called commuting regular ring (resp‎. ‎semigroupif‎ for each $x,y\\in R$ there exists $a\\in R$‎ such that$xy=yxayx$‎. ‎In this paper‎, ‎we introduce the concept of‎‎commuting $\\pi$-regular rings (resp‎. ‎semigroups and‎‎study various properties of them.

  7. Asymmetric transmission in planar chiral split-ring metamaterials: Microscopic Lorentz-theory approach

    DEFF Research Database (Denmark)

    Novitsky, Andrey; Galynsky, Vladimir M.; Zhukovsky, Sergei

    2012-01-01

    The electronic Lorentz theory is employed to explain the optical properties of planar split-ring metamaterials. Starting from the dynamics of individual free carriers, the electromagnetic response of an individual split-ring meta-atom is determined, and the effective permittivity tensor...... of the metamaterial is calculated for normal incidence of light. Whenever the split ring lacks in-plane mirror symmetry, the corresponding permittivity tensor has a crystallographic structure of an elliptically dichroic medium, and the metamaterial exhibits optical properties of planar chiral structures. Its...... transmission spectra are different for right-handed versus left-handed circular polarization of the incident wave, so the structure changes its transmittance when the direction of incidence is reversed. The magnitude of this change is shown to be related to the geometric parameters of the split ring...

  8. History of Neptune's Ring Arcs

    Science.gov (United States)

    Esposito, L. W.; Colwell, J. E.; Canup, R. M.

    1997-07-01

    The recent dynamical calculations for Neptune's Adams ring arcs by Foryta and Sicardy (1996) and Hanninen and Porco (1997) determine the basic evolutionary parameters for this system. The ring evolution is dominated by stochastic events, particularly chaotic motion that causes a migration between the corotation sites (FS96) and collisions near quadrature (HP97). A basic problem is that the high velocity collisions that produce the dusty arcs at the Galatea corotation resonances rapidly depopulate these sites (Colwell and Esposito 1990). With the new results in hand for the evolution of the ring particles over periods of less than a century, we can now calculate the long-term stochastic evolution of the Adams ring. Using a finite Markov chain as a model for this stochastic process, we follow the suggestion by FS96 that corotation sites provide preferential locations for accretion. A more general conclusion is that the longitudinal concentration of material in a few nearby sites (and that the majority of the Adams ring material is residing there) requires either an exceedingly recent event (EC92) or that the corotation sites be absorbing states of the Markov chain.In the latter case, the competing processes of chaotic diffusion and frustrated accretion can provide the arc and clump features as recurrent transient events near the Roche limit. Similar phenomena would be expected for Saturn's F and G rings.

  9. The ring of the narcissist.

    Science.gov (United States)

    Shengold, L

    1995-12-01

    The author has not attempted a complete exposition of the meaning of rings--which can refer to and symbolise many aspects of relationships with other human beings from 'transitional objects' of early development (Winnicott) to all sorts of bonds of loyalty, friendship, and love in the life of the child and the adult. He stresses the meanings of the ring from the point of view of early narcissistic development--the 'body ego' time of early development in which symbolism (in Freud's sense) develops. The clinical and literary examples therefore illustrate the use of rings as magical narcissistic symbols--part subject and part object--derived developmentally from the body ego and ultimately from the body sphincters. Endowed with these regressive primitive meanings, rings are felt to have magical powers that can either preserve or destroy, and that can control emotions in the self and in others. In the course of ordinary or pathological narcissistic regressions, rings (consciously associated with many positive feelings and achievements) also partake, in so far as they are 'Freudian' symbols, of qualities associated with developmentally early defensive mechanisms and modes of psychic functioning (projection, introjection; idealisation, devaluation). In the cases cited, rings seemed specifically associated with (and to symbolise) sphincteric (largely anal) narcissistic defensiveness--the mind functioning as an emotional sphincteric counterpart primarily deadening and distancing affect but intermittently letting through primitive rage and primal polymorphous perverse sexual impulses.

  10. Collar nut and thrust ring

    Science.gov (United States)

    Lowery, Guy B.

    1991-01-01

    A collar nut comprises a hollow cylinder having fine interior threads at one end for threadably engaging a pump mechanical seal assembly and an inwardly depending flange at the other end. The flange has an enlarged portion with a groove for receiving an O-ring for sealing against the intrusion of pumpage from the exterior. The enlarged portion engages a thrust ring about the pump shaft for crushing a hard O-ring, such as a graphite O-ring. The hard O-ring seals the interior of the mechanical seal assembly and pump housing against the loss of lubricants or leakage of pumpage. The fine threads of the hollow cylinder provide the mechanical advantage for crushing the hard O-ring evenly and easily with a hand tool from the side of the collar nut rather than by tightening a plurality of bolts from the end and streamlines the exterior surface of the mechanical seal. The collar nut avoids the spatial requirements of bolt heads at the end of a seal and associated bolt head turbulence.

  11. Sustainable reverse logistics for household plastic waste

    NARCIS (Netherlands)

    Bing, X.

    2014-01-01

    Summary of the thesis titled “Sustainable Reverse Logistics for Household Plastic Waste” PhD Candidate: Xiaoyun Bing Recycled plastic can be used in the manufacturing of plastic products to reduce the use of virgin plastics material. The cost of recycled plastics is usually lower than th

  12. Sustainable reverse logistics for household plastic waste

    NARCIS (Netherlands)

    Bing, X.

    2014-01-01

    Summary of the thesis titled “Sustainable Reverse Logistics for Household Plastic Waste” PhD Candidate: Xiaoyun Bing Recycled plastic can be used in the manufacturing of plastic products to reduce the use of virgin plastics material. The cost of recycled plastics is usually lower than

  13. Sustainable reverse logistics for household plastic waste

    NARCIS (Netherlands)

    Bing, X.

    2014-01-01

    Summary of the thesis titled “Sustainable Reverse Logistics for Household Plastic Waste” PhD Candidate: Xiaoyun Bing Recycled plastic can be used in the manufacturing of plastic products to reduce the use of virgin plastics material. The cost of recycled plastics is usually lower than th

  14. Plastics recycling: challenges and opportunities.

    Science.gov (United States)

    Hopewell, Jefferson; Dvorak, Robert; Kosior, Edward

    2009-07-27

    Plastics are inexpensive, lightweight and durable materials, which can readily be moulded into a variety of products that find use in a wide range of applications. As a consequence, the production of plastics has increased markedly over the last 60 years. However, current levels of their usage and disposal generate several environmental problems. Around 4 per cent of world oil and gas production, a non-renewable resource, is used as feedstock for plastics and a further 3-4% is expended to provide energy for their manufacture. A major portion of plastic produced each year is used to make disposable items of packaging or other short-lived products that are discarded within a year of manufacture. These two observations alone indicate that our current use of plastics is not sustainable. In addition, because of the durability of the polymers involved, substantial quantities of discarded end-of-life plastics are accumulating as debris in landfills and in natural habitats worldwide. Recycling is one of the most important actions currently available to reduce these impacts and represents one of the most dynamic areas in the plastics industry today. Recycling provides opportunities to reduce oil usage, carbon dioxide emissions and the quantities of waste requiring disposal. Here, we briefly set recycling into context against other waste-reduction strategies, namely reduction in material use through downgauging or product reuse, the use of alternative biodegradable materials and energy recovery as fuel. While plastics have been recycled since the 1970s, the quantities that are recycled vary geographically, according to plastic type and application. Recycling of packaging materials has seen rapid expansion over the last decades in a number of countries. Advances in technologies and systems for the collection, sorting and reprocessing of recyclable plastics are creating new opportunities for recycling, and with the combined actions of the public, industry and governments it

  15. Plastics recycling: challenges and opportunities

    Science.gov (United States)

    Hopewell, Jefferson; Dvorak, Robert; Kosior, Edward

    2009-01-01

    Plastics are inexpensive, lightweight and durable materials, which can readily be moulded into a variety of products that find use in a wide range of applications. As a consequence, the production of plastics has increased markedly over the last 60 years. However, current levels of their usage and disposal generate several environmental problems. Around 4 per cent of world oil and gas production, a non-renewable resource, is used as feedstock for plastics and a further 3–4% is expended to provide energy for their manufacture. A major portion of plastic produced each year is used to make disposable items of packaging or other short-lived products that are discarded within a year of manufacture. These two observations alone indicate that our current use of plastics is not sustainable. In addition, because of the durability of the polymers involved, substantial quantities of discarded end-of-life plastics are accumulating as debris in landfills and in natural habitats worldwide. Recycling is one of the most important actions currently available to reduce these impacts and represents one of the most dynamic areas in the plastics industry today. Recycling provides opportunities to reduce oil usage, carbon dioxide emissions and the quantities of waste requiring disposal. Here, we briefly set recycling into context against other waste-reduction strategies, namely reduction in material use through downgauging or product reuse, the use of alternative biodegradable materials and energy recovery as fuel. While plastics have been recycled since the 1970s, the quantities that are recycled vary geographically, according to plastic type and application. Recycling of packaging materials has seen rapid expansion over the last decades in a number of countries. Advances in technologies and systems for the collection, sorting and reprocessing of recyclable plastics are creating new opportunities for recycling, and with the combined actions of the public, industry and governments it

  16. Fatigue reliability for LNG carrier

    Institute of Scientific and Technical Information of China (English)

    Xiao Taoyun; Zhang Qin; Jin Wulei; Xu Shuai

    2011-01-01

    The procedure of reliability-based fatigue analysis of liquefied natural gas (LNG) carrier of membrane type under wave loads is presented. The stress responses of the hotspots in regular waves with different wave heading angles and wave lengths are evaluated by global ship finite element method (FEM). Based on the probabilistic distribution function of hotspots' short-term stress-range using spectral-based analysis, Weibull distribution is adopted and discussed for fitting the long-term probabilistic distribution of stress-range. Based on linear cumulative damage theory, fatigue damage is characterized by an S-N relationship, and limit state function is established. Structural fatigue damage behavior of several typical hotspots of LNG middle ship section is clarified and reliability analysis is performed. It is believed that the presented results and conclusions can be of use in calibration for practical design and initial fatigue safety evaluation for membrane type LNG carrier.

  17. A Customized Finger Brachytherapy Carrier

    OpenAIRE

    Wadhwa, Supneet Singh; Duggal, Nidhi

    2013-01-01

    In recent years, radiation therapy has been used with increasing frequency in the management of neoplasms of the head and neck region. Brachytherapy is a method of radiation treatment in which sealed radioactive sources are used to deliver the dose a short distance by interstitial (direct insertion into tissue), intracavitary (placement within a cavity) or surface application (molds). Mold brachytherapy is radiation delivered via a custom-fabricated carriers, designed to provide a more consta...

  18. Symmetry group analysis of an ideal plastic flow

    CERN Document Server

    Lamothe, Vincent

    2011-01-01

    In this paper, we study the Lie point symmetry group of a system describing an ideal plastic plane flow in two dimensions in order to find analytical solutions. The infinitesimal generators that span the Lie algebra for this system are obtained. We completely classify the subalgebras of up to codimension two in conjugacy classes under the action of the symmetry group. Based on invariant forms, we use Ansatzes to compute symmetry reductions in such a way that the obtained solutions cover simultaneously many invariant and partially invariant solutions. We calculate solutions of the algebraic, trigonometric, inverse trigonometric and elliptic type. Some solutions depending on one or two arbitrary functions of one variable have also been found. In some cases, the shape of a potentially feasible extrusion die corresponding to the solution is deduced. These tools could be used to thin, curve, undulate or shape a ring in an ideal plastic material.

  19. Accretion in Saturn's F Ring

    Science.gov (United States)

    Meinke, B. K.; Esposito, L. W.; Stewart, G.

    2012-12-01

    Saturn's F ring is the solar system's principal natural laboratory for direct observation of accretion and disruption processes. The ring resides in the Roche zone, where tidal disruption competes with self-gravity, which allows us to observe the lifecycle of moonlets. Just as nearby moons create structure at the B ring edge (Esposito et al. 2012) and the Keeler gap (Murray 2007), the F ring "shepherding" moons Prometheus and Pandora stir up ring material and create observably changing structures on timescales of days to decades. In fact, Beurle et al (2010) show that Prometheus makes it possible for "distended, yet gravitationally coherent clumps" to form in the F ring, and Barbara and Esposito (2002) predicted a population of ~1 km bodies in the ring. In addition to the observations over the last three decades, the Cassini Ultraviolet Imaging Spectrograph (UVIS) has detected 27 statistically significant features in 101 occultations by Saturn's F ring since July 2004. Seventeen of those 27 features are associated with clumps of ring material. Two features are opaque in occultation, which makes them candidates for solid objects, which we refer to as Moonlets. The 15 other features partially block stellar signal for 22 m to just over 3.7 km along the radial expanse of the occultation. Upon visual inspection of the occultation profile, these features resemble Icicles, thus we will refer to them as such here. The density enhancements responsible for such signal attenuations are likely due to transient clumping of material, evidence that aggregations of material are ubiquitous in the F ring. Our lengthy observing campaign reveals that Icicles are likely transient clumps, while Moonlets are possible solid objects. Optical depth is an indicator of clumping because more-densely aggregated material blocks more light; therefore, it is natural to imagine moonlets as later evolutionary stage of icicle, when looser clumps of material compact to form a feature that appears

  20. Plastic in North Sea Fish

    NARCIS (Netherlands)

    Foekema, E.M.; Gruijter, de C.; Mergia, M.T.; Franeker, van J.A.; Murk, A.J.; Koelmans, A.A.

    2013-01-01

    To quantify the occurrence of ingested plastic in fish species caught at different geographical positions in the North Sea, and to test whether the fish condition is affected by ingestion of plastics, 1203 individual fish of seven common North Sea species were investigated: herring, gray gurnard, wh

  1. The scope of plastic surgery

    African Journals Online (AJOL)

    2013-08-03

    Aug 3, 2013 ... areas of surgery (especially general surgery), plastic surgeons are arguably the .... Who do you feel are experts in laparoscopic surgery? e (general surgeons) a. Maxillofacial .... of pressure sore. ORIF = open reduction internal fixation. ... Plastic versus cosmetic surgery: What's the difference? Plast Reconstr.

  2. New Life for Old Plastics

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    Recycling joint venture utilizes innovative technology to reuse plastics Recycling,despite its green connotations,can be a messy business.In China,more than 400,000 companies are engaged in plastic recycling,but 70 percent of them are family enterprises,

  3. Computational strain gradient crystal plasticity

    DEFF Research Database (Denmark)

    Niordson, Christian Frithiof; Kysar, Jeffrey W.

    2014-01-01

    of plane crystal plasticity are studied: pure shear of a single crystal between rigid platens as well as plastic deformation around cylindrical voids in hexagonal close packed and face centered cubic crystals. Effective in-plane constitutive slip parameters for plane strain deformation of specifically...

  4. Architecture of European Plastic Surgery

    NARCIS (Netherlands)

    Nicolai, J. -P. A.; Banic, A.; Molea, G.; Mazzola, R.; Poell, J. G.

    2006-01-01

    The architecture of European Plastic Surgery was published in 1996 [Nicolai JPA, Scuderi N. Plastic surgical Europe in an organogram. Eur J Plast Surg 1996; 19: 253-6.] It is the objective of this paper to update information of that article. Continuing medical education (CME), science, training,

  5. Preventative maintenance of straddle carriers

    Directory of Open Access Journals (Sweden)

    Si Li

    2015-02-01

    Full Text Available Background: Robotic vehicles such as straddle carriers represent a popular form of cargo handling amongst container terminal operators.Objectives: The purpose of this industry-driven study is to model preventative maintenance (PM influences on the operational effectiveness of straddle carriers.Method: The study employs historical data consisting of 21 273 work orders covering a 27-month period. Two models are developed, both of which forecast influences of PM regimes for different types of carrier.Results: The findings of the study suggest that the reliability of the straddle fleet decreases with increased intervals of PM services. The study also finds that three factors – namely resources, number of new straddles, and the number of new lifting work centres – influence the performances of straddles.Conclusion: The authors argue that this collaborative research exercise makes a significant contribution to existing supply chain management literature, particularly in the area of operations efficiency. The study also serves as an avenue to enhance relevant management practice.

  6. Plastics for corrosion inhibition

    CERN Document Server

    Goldade, Victor A; Makarevich, Anna V; Kestelman, Vladimir N

    2005-01-01

    The development of polymer composites containing inhibitors of metal corrosion is an important endeavour in modern materials science and technology. Corrosion inhibitors can be located in a polymer matrix in the solid, liquid or gaseous phase. This book details the thermodynamic principles for selecting these components, their compatibility and their effectiveness. The various mechanisms of metal protection – barrier, inhibiting and electromechanical – are considered, as are the conflicting requirements placed on the structure of the combined material. Two main classes of inhibited materials (structural and films/coatings) are described in detail. Examples are given of structural plastics used in friction units subjected to mechano-chemical wear and of polymer films/coatings for protecting metal objects against corrosion.

  7. Double acting stirling engine piston ring

    Science.gov (United States)

    Howarth, Roy B.

    1986-01-01

    A piston ring design for a Stirling engine wherein the contact pressure between the piston and the cylinder is maintained at a uniform level, independent of engine conditions through a balancing of the pressure exerted upon the ring's surface and thereby allowing the contact pressure on the ring to be predetermined through the use of a preloaded expander ring.

  8. Responsible implementation of expanded carrier screening.

    Science.gov (United States)

    Henneman, Lidewij; Borry, Pascal; Chokoshvili, Davit; Cornel, Martina C; van El, Carla G; Forzano, Francesca; Hall, Alison; Howard, Heidi C; Janssens, Sandra; Kayserili, Hülya; Lakeman, Phillis; Lucassen, Anneke; Metcalfe, Sylvia A; Vidmar, Lovro; de Wert, Guido; Dondorp, Wybo J; Peterlin, Borut

    2016-06-01

    This document of the European Society of Human Genetics contains recommendations regarding responsible implementation of expanded carrier screening. Carrier screening is defined here as the detection of carrier status of recessive diseases in couples or persons who do not have an a priori increased risk of being a carrier based on their or their partners' personal or family history. Expanded carrier screening offers carrier screening for multiple autosomal and X-linked recessive disorders, facilitated by new genetic testing technologies, and allows testing of individuals regardless of ancestry or geographic origin. Carrier screening aims to identify couples who have an increased risk of having an affected child in order to facilitate informed reproductive decision making. In previous decades, carrier screening was typically performed for one or few relatively common recessive disorders associated with significant morbidity, reduced life-expectancy and often because of a considerable higher carrier frequency in a specific population for certain diseases. New genetic testing technologies enable the expansion of screening to multiple conditions, genes or sequence variants. Expanded carrier screening panels that have been introduced to date have been advertised and offered to health care professionals and the public on a commercial basis. This document discusses the challenges that expanded carrier screening might pose in the context of the lessons learnt from decades of population-based carrier screening and in the context of existing screening criteria. It aims to contribute to the public and professional discussion and to arrive at better clinical and laboratory practice guidelines.

  9. Responsible implementation of expanded carrier screening

    Science.gov (United States)

    Henneman, Lidewij; Borry, Pascal; Chokoshvili, Davit; Cornel, Martina C; van El, Carla G; Forzano, Francesca; Hall, Alison; Howard, Heidi C; Janssens, Sandra; Kayserili, Hülya; Lakeman, Phillis; Lucassen, Anneke; Metcalfe, Sylvia A; Vidmar, Lovro; de Wert, Guido; Dondorp, Wybo J; Peterlin, Borut

    2016-01-01

    This document of the European Society of Human Genetics contains recommendations regarding responsible implementation of expanded carrier screening. Carrier screening is defined here as the detection of carrier status of recessive diseases in couples or persons who do not have an a priori increased risk of being a carrier based on their or their partners' personal or family history. Expanded carrier screening offers carrier screening for multiple autosomal and X-linked recessive disorders, facilitated by new genetic testing technologies, and allows testing of individuals regardless of ancestry or geographic origin. Carrier screening aims to identify couples who have an increased risk of having an affected child in order to facilitate informed reproductive decision making. In previous decades, carrier screening was typically performed for one or few relatively common recessive disorders associated with significant morbidity, reduced life-expectancy and often because of a considerable higher carrier frequency in a specific population for certain diseases. New genetic testing technologies enable the expansion of screening to multiple conditions, genes or sequence variants. Expanded carrier screening panels that have been introduced to date have been advertised and offered to health care professionals and the public on a commercial basis. This document discusses the challenges that expanded carrier screening might pose in the context of the lessons learnt from decades of population-based carrier screening and in the context of existing screening criteria. It aims to contribute to the public and professional discussion and to arrive at better clinical and laboratory practice guidelines. PMID:26980105

  10. 14 CFR Section 04 - Air Carrier Groupings

    Science.gov (United States)

    2010-01-01

    ... Aeronautics and Space OFFICE OF THE SECRETARY, DEPARTMENT OF TRANSPORTATION (AVIATION PROCEEDINGS) ECONOMIC... carrier to a specific group of carriers will be reviewed periodically by the Director, Office of Airline... Office of Airline Statistics will issue an updated listing of the carrier groups on an annual basis. A...

  11. Spacelab carrier complement thermal design and performance

    Science.gov (United States)

    Bancroft, S.; Key, R.; Kittredge, S.

    1992-01-01

    The present discussion of the Spacelab carrier complement, which encompasses a Module Carrier, a Module-Pallet Carrier, and a Multiplexer/Demultiplexer Pallet, gives attention to both active and passive thermal performance capabilities, and presents ground testing and analytical results obtained to date. An account is given of the prospective use of a Spacelab Multipurpose Experiment Support Structure.

  12. 7 CFR 33.4 - Carrier.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Carrier. 33.4 Section 33.4 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... ISSUED UNDER AUTHORITY OF THE EXPORT APPLE ACT Definitions § 33.4 Carrier. Carrier means any common...

  13. Universal features of amorphous plasticity

    Science.gov (United States)

    Budrikis, Zoe; Castellanos, David Fernandez; Sandfeld, Stefan; Zaiser, Michael; Zapperi, Stefano

    2017-07-01

    Plastic yielding of amorphous solids occurs by power-law distributed deformation avalanches whose universality is still debated. Experiments and molecular dynamics simulations are hampered by limited statistical samples, and although existing stochastic models give precise exponents, they require strong assumptions about fixed deformation directions, at odds with the statistical isotropy of amorphous materials. Here, we introduce a fully tensorial, stochastic mesoscale model for amorphous plasticity that links the statistical physics of plastic yielding to engineering mechanics. It captures the complex shear patterning observed for a wide variety of deformation modes, as well as the avalanche dynamics of plastic flow. Avalanches are described by universal size exponents and scaling functions, avalanche shapes, and local stability distributions, independent of system dimensionality, boundary and loading conditions, and stress state. Our predictions consistently differ from those of mean-field depinning models, providing evidence that plastic yielding is a distinct type of critical phenomenon.

  14. Phenotypic Plasticity and Species Coexistence.

    Science.gov (United States)

    Turcotte, Martin M; Levine, Jonathan M

    2016-10-01

    Ecologists are increasingly interested in predicting how intraspecific variation and changing trait values impact species interactions and community composition. For many traits, much of this variation is caused by phenotypic plasticity, and thus the impact of plasticity on species coexistence deserves robust quantification. Partly due to a lack of sound theoretical expectations, empirical studies make contradictory claims regarding plasticity effects on coexistence. Our critical review of this literature, framed in modern coexistence theory, reveals that plasticity affects species interactions in ways that could impact stabilizing niche differences and competitive asymmetries. However, almost no study integrates these measures to quantify the net effect of plasticity on species coexistence. To address this challenge, we outline novel empirical approaches grounded in modern theory.

  15. Imaging brain plasticity after trauma

    Institute of Scientific and Technical Information of China (English)

    Zhifeng Kou; Armin Iraji

    2014-01-01

    The brain is highly plastic after stroke or epilepsy;however, there is a paucity of brain plasticity investigation after traumatic brain injury (TBI). This mini review summarizes the most recent evidence of brain plasticity in human TBI patients from the perspective of advanced magnetic resonance imaging. Similar to other forms of acquired brain injury, TBI patients also demonstrat-ed both structural reorganization as well as functional compensation by the recruitment of other brain regions. However, the large scale brain network alterations after TBI are still unknown, and the ifeld is still short of proper means on how to guide the choice of TBI rehabilitation or treat-ment plan to promote brain plasticity. The authors also point out the new direction of brain plas-ticity investigation.

  16. Size effects in crystal plasticity

    DEFF Research Database (Denmark)

    Borg, Ulrik

    2007-01-01

    Numerical analyses of plasticity size effects have been carried out for different problems using a developed strain gradient crystal plasticiy theory. The theory employs higher order stresses as work conjugates to slip gradients and uses higher order boundary conditions. Problems on localization...... of plastic flow in a single crystal, grain boundary effects in a bicrystal, and grain size effects in a polycrystal are studied. Single crystals containing micro-scale voids have also been analyzed at different loading conditions with focus on the stress and deformation fields around the voids, on void...... growth and interaction between neighboring voids, and on a comparison between the developed strain gradient crystal plasticity theory and a discrete dislocation plasticity theory. Furthermore, voids and rigid inclusions in isotropic materials have been studied using a strain gradient plasticity theory...

  17. Charge transport optimization in CZT ring-drift detectors

    Science.gov (United States)

    Boothman, V.; Alruhaili, A.; Perumal, V.; Sellin, P.; Lohstroh, A.; Sawhney, K.; Kachanov, S.

    2015-12-01

    Ring-drift design has been applied to large (7.5~\\text{mm}× 7.5~\\text{mm}× 2.3 mm) cadmium zinc telluride (CZT) devices. This low-noise, single-carrier-sensing configuration is the gold standard for spectroscopic silicon x-ray detectors. By combining the advantages of ring-drift with the high quantum efficiency and room-temperature operating capabilities of CZT, a simple and compact device for high-resolution spectroscopy of x-rays in the range 50-500 keV can be created. Quality of CZT crystals has improved greatly in recent years and electron-only sensing overcomes the problem of inherently poor hole transport in II-VI semiconductors. The spatial response of our 3-ring CZT device was studied by microbeam scanning while the voltages applied to all electrodes were systematically varied. Maximum active radius extended to 2.3 mm, beyond the second ring. Resolution was limited by electronic noise. Our results show that the lateral field and its ratio to the bulk field exert a crucial influence on active area, peak position and sensitivity. CZT and the device geometry were modelled in 3D with Sentaurus TCAD. Line scans were simulated and trends in performance with bias conditions matched experimental data, validating the model. We aimed to optimize the resolution, sensitivity and active radius of the device. Fields and charge drift were visualized and the active volume was mapped in 3D to improve understanding of the factors governing performance including number of rings, their widths, positions and bias.

  18. Extensions and Pullbacks in QB-rings

    OpenAIRE

    Ara, Pere; Pedersen, Gert K.; Perera, Francesc

    2001-01-01

    We prove a new extension result for $QB-$rings that allows us to examine extensions of rings where the ideal is purely infinite and simple. We then use this result to explore various constructions that provide new examples of $QB-$rings. More concretely, we show that a surjective pullback of two $QB-$rings is usually again a $QB-$ring. Specializing to the case of an extension of a semi-prime ideal $I$ of a unital ring $R$, the pullback setting leads naturally to the study of rings whose multi...

  19. The ribbon of the rings: the stability of the rings

    Science.gov (United States)

    Florinski, V.

    2016-11-01

    The astounding result of the Voyager 1 observations in the outer heliosheath region is the Kolmogorov-like spectrum of magnetic fluctuations, consistent with the ambient spectrum of interstellar turbulence deduced from remote sensing. Such quiet conditions appear to be incompatible with the ionization of the neutral solar wind hydrogen atoms by charge exchange, which would generate abundant turbulent fluctuations due to an instability of the resulting proton ring. Here we revisit the problem of stability of ring and shell distributions embedded in a warm plasma characteristic of the outer heliosheath. We show that ion rings with parallel velocity dispersion between a few km/s and the core thermal speed are stable, while those outside these bounds are subject to magnetic-fluctuation-producing left- and righthanded instabilities. Wave generation by the instability is too efficient to be transported to shorter scales and converted into heat by the turbulent cascade.

  20. Testing phenanthrene distribution properties of virgin plastic pellets and plastic eroded pellets found on Lesvos island beaches (Greece).

    Science.gov (United States)

    Karapanagioti, Hrissi K; Klontza, Irene

    2008-05-01

    Plastic pellets have been characterized as toxic pollutant carriers throughout the world oceans and coastal zones. However, their sorptive properties are not yet well understood. In the present study, virgin pellets and plastic eroded pellets (PEP) are used to elucidate their distribution characteristics through distribution kinetic studies. Distribution occurs through diffusion into the pellet for all materials (polyethylene, polyoxymethylene, and PEP) except polypropylene (PP). Although diffusion into the polymer happens with similar rates for both freshwater and saltwater external solutions, apparent diffusion is dependent on the solution salinity because it results in higher equilibrium distribution coefficients. Distribution coefficient into the PEP is higher and diffusion is slower than into the virgin materials. This is attributed to increased crystallinity of the PEP due to weathering. PP demonstrates diffusion rates that are increased by salinity and is apparently faster than into the other polymers suggesting a surface diffusion process.

  1. Nano-Ceramic Coated Plastics

    Science.gov (United States)

    Cho, Junghyun

    2013-01-01

    Plastic products, due to their durability, safety, and low manufacturing cost, are now rapidly replacing cookware items traditionally made of glass and ceramics. Despite this trend, some still prefer relatively expensive and more fragile ceramic/glassware because plastics can deteriorate over time after exposure to foods, which can generate odors, bad appearance, and/or color change. Nano-ceramic coatings can eliminate these drawbacks while still retaining the advantages of the plastic, since the coating only alters the surface of the plastic. The surface coating adds functionality to the plastics such as self-cleaning and disinfectant capabilities that result from a photocatalytic effect of certain ceramic systems. These ceramic coatings can also provide non-stick surfaces and higher temperature capabilities for the base plastics without resorting to ceramic or glass materials. Titanium dioxide (TiO2) and zinc oxide (ZnO) are the candidates for a nano-ceramic coating to deposit on the plastics or plastic films used in cookware and kitchenware. Both are wide-bandgap semiconductors (3.0 to 3.2 eV for TiO2 and 3.2 to 3.3 eV for ZnO), so they exhibit a photocatalytic property under ultraviolet (UV) light. This will lead to decomposition of organic compounds. Decomposed products can be easily washed off by water, so the use of detergents will be minimal. High-crystalline film with large surface area for the reaction is essential to guarantee good photocatalytic performance of these oxides. Low-temperature processing (nano-ceramic coatings (TiO2, ZnO) on plastic materials (silicone, Teflon, PET, etc.) that can possess both photocatalytic oxide properties and flexible plastic properties. Processing cost is low and it does not require any expensive equipment investment. Processing can be scalable to current manufacturing infrastructure.

  2. Biodegradability of degradable plastic waste.

    Science.gov (United States)

    Agamuthu, P; Faizura, Putri Nadzrul

    2005-04-01

    Plastic waste constitutes the third largest waste volume in Malaysian municipal solid waste (MSW), next to putrescible waste and paper. The plastic component in MSW from Kuala Lumpur averages 24% (by weight), whereas the national mean is about 15%. The 144 waste dumps in the country receive about 95% of the MSW, including plastic waste. The useful life of the landfills is fast diminishing as the plastic waste stays un-degraded for more than 50 years. In this study the compostability of polyethylene and pro-oxidant additive-based environmentally degradable plastics (EDP) was investigated. Linear low-density polyethylene (LLDPE) samples exposed hydrolytically or oxidatively at 60 degrees C showed that the abiotic degradation path was oxidative rather than hydrolytic. There was a weight loss of 8% and the plastic has been oxidized as shown by the additional carbonyl group exhibited in the Fourier transform infra red (FTIR) Spectrum. Oxidation rate seemed to be influenced by the amount of pro-oxidant additive, the chemical structure and morphology of the plastic samples, and the surface area. Composting studies during a 45-day experiment showed that the percentage elongation (reduction) was 20% for McD samples [high-density polyethylene, (HDPE) with 3% additive] and LL samples (LLDPE with 7% additive) and 18% reduction for totally degradable plastic (TDP) samples (HDPE with 3% additive). Lastly, microbial experiments using Pseudomonas aeroginosa on carbon-free media with degradable plastic samples as the sole carbon source, showed confirmatory results. A positive bacterial growth and a weight loss of 2.2% for degraded polyethylene samples were evident to show that the degradable plastic is biodegradable.

  3. Finite Element Analysis of Residual Stress and Distortion in an Eccentric Ring Induced by Quenching

    Institute of Scientific and Technical Information of China (English)

    YAOXin; ZHULi-hua; LIM.Victor

    2004-01-01

    The residual stresses and distortion induced by quenching in an eccentric ring were investigated in this study with finite element method. The ring was made of AISI 52100 steel. A fully coupled 3D temperature-displacement analysis was performed to simulate heat transfer, phase transformations, and mechanical stresses and strains during the heating and subsequent quenching processes. Commercial FEA package ABAQUS/Standard 6.4 was used for the analyses along with user subroutines developed by the authors to model the thermal and mechanical constitutive behavior. The simulation results show that transformation plasticity plays an important role on the residual stress distribution.

  4. Research on parameters optimization of bilateral ring gear blank-holder in thick-plate fine blanking

    Directory of Open Access Journals (Sweden)

    C.J.Su

    2014-10-01

    Full Text Available To compensate for the poor quality of thick-plate blanking parts in cross-section, this paper suggests using the optimizing bilateral ring gear holder parameters to increase burnish zone and improve cutting precision. With the bilateral gear ring, the hydrostatic pressure of shear deformation zone will increase, plasticity of the material will be lifted to maximum and quality of the cross section will be raised. This paper establishes 8mm AISI-1020 fine blanking model by DEFORM2D, analysis different ring gear parameters and clearance that are influenced the stress-strain and cross section quality to predict forming defects. By using the bilateral gear ring blank holder, the poor quality of thick-plate blanking section is successfully enhanced. Therefore, the bilateral gear ring blank holder is vital to improve the quality of blanking parts and provide the reliable theory basis for the practical engineering application.

  5. Intrinsic structure in Saturn's rings

    Science.gov (United States)

    Albers, N.

    2015-10-01

    Saturn's rings are the most prominent in our Solar system and one example of granular matter in space. Dominated by tides and inelastic collisions the system is highly flattened being almost 300000km wide while only tens of meters thick. Individual particles are composed of primarily water ice and range from microns to few tens of meters in size. Apparent patterns comprise ringlets, gaps, kinematic wakes, propellers, bending waves, and the winding spiral arms of density waves. These large-scale structures are perturbations foremost created by external as well as embedded moons. Observations made by the Cassini spacecraft currently in orbit around Saturn show these structures in unprecedented detail. But high-resolution measurements reveal the presence of small-scale structures throughout the system. These include self-gravity wakes (50-100m), overstable waves (100-300m), subkm structure at the A and B ring edges, "straw" and "ropy" structures (1-3km), and the C ring "ghosts". Most of these had not been anticipated and are found in perturbed regions, driven by resonances with external moons, where the system undergoes periodic phases of compression and relaxation that correlate with the presence of structure. High velocity dispersion and the presence of large clumps imply structure formation on time scales as short as one orbit (about 10 hours). The presence of these intrinsic structures is seemingly the response to varying local conditions such as internal density, optical depth, underlying particle size distribution, granular temperature, and distance from the central planet. Their abundance provides evidence for an active and dynamic ring system where aggregation and fragmentation are ongoing on orbital timescales. Thus a kinetic description of the rings may be more appropriate than the fluid one. I will present Cassini Ultraviolet Spectrometer (UVIS) High Speed Photometer (HSP) occultations, Voyager 1 and 2 Imaging Science Subsystem (ISS), and high

  6. Ring wormholes via duality rotations

    Directory of Open Access Journals (Sweden)

    Gary W. Gibbons

    2016-09-01

    Full Text Available We apply duality rotations and complex transformations to the Schwarzschild metric to obtain wormhole geometries with two asymptotically flat regions connected by a throat. In the simplest case these are the well-known wormholes supported by phantom scalar field. Further duality rotations remove the scalar field to yield less well known vacuum metrics of the oblate Zipoy–Voorhees–Weyl class, which describe ring wormholes. The ring encircles the wormhole throat and can have any radius, whereas its tension is always negative and should be less than −c4/4G. If the tension reaches the maximal value, the geometry becomes exactly flat, but the topology remains non-trivial and corresponds to two copies of Minkowski space glued together along the disk encircled by the ring. The geodesics are straight lines, and those which traverse the ring get to the other universe. The ring therefore literally produces a hole in space. Such wormholes could perhaps be created by negative energies concentrated in toroidal volumes, for example by vacuum fluctuations.

  7. Dream of Isochronous Ring Again

    CERN Document Server

    Hama, H

    2005-01-01

    More than 20 years ago, D.A.G. Deacon proposed an isochronous storage ring for FEL to avoid bunch heating and decreasing instantaneous gain [1]. Some of low momentum compaction (alpha) operations have been carried out, and recently coherent infrared radiation are observed on a 3rd generation light source. Because the 3rd generation rings are optimized to obtain very low emittance beam, the dispersion function in the arc sections are much reduced by introducing large bending radius, so that those are very big machines. Meanwhile N.A. Vinokurov et al. recently proposed a ring type SASE FEL based on a complete isochronous bending transport [2]. At least, experimental and theoretical study of the isochronous ring so far suggests nonlinear effects resulted from higher order dispersion and chromaticity declines the "complete" isochronous system. On the other hand, in a wavelength region of THz, tolerance of the path length along a turn of the ring seems to be within our reach. A concept to preserve of a form factor...

  8. Burnside Rings of Fusion Systems

    DEFF Research Database (Denmark)

    Reeh, Sune Precht

    of the characteristic idempotent of F { the unique idempotent in the p-local double Burnside ring of S satisfying properties of Linckelmann and Webb. We describe this idempotent both in terms of fixed points and as a linear combination of transitive bisets. Additionally, using fixed points we determine the map......In this thesis we study the interactions between saturated fusion systems and group actions of the underlying p-groups. For a saturated fusion system F on a finite p-group S we construct the Burnside ring of F in terms of the finite S-sets whose actions respect the structure of the fusion system......, and we produce a basis for the Burnside ring that shares properties with the transitive sets for a finite group. We construct a transfer map from the p-local Burnside ring of the underlying p-group S to the p-local Burnside ring of F. Using such transfer maps, we give a new explicit construction...

  9. Ring polymers in confined geometries

    CERN Document Server

    Usatenko, Z; Kuterba, P

    2016-01-01

    The investigation of a dilute solution of phantom ideal ring polymers and ring polymers with excluded volume interactions (EVI) in a good solvent confined in a slit geometry of two parallel repulsive walls and in a solution of colloidal particles of big size were performed. Taking into account the correspondence between the field theoretical $\\phi^4$ $O(n)$-vector model in the limit $n\\to 0$ and the behavior of long-flexible polymer chains in a good solvent the correspondent depletion interaction potentials, depletion forces and the forces which exert phantom ideal ring and ring polymer chains with EVI on the walls were obtained in the framework of the massive field theory approach at fixed space dimensions d=3 up to one-loop order. Additionally, the investigation of a dilute solution of phantom ideal ring polymers in a slit geometry of two inert walls and mixed walls with one repulsive and other one inert wall were performed and correspondent depletion interaction potentials and the depletion forces were cal...

  10. Ring wormholes via duality rotations

    CERN Document Server

    Gibbons, Gary W

    2016-01-01

    We apply duality rotations and complex transformations to the Schwarzschild metric to obtain wormhole geometries with two asymptotically flat regions connected by a throat. In the simplest case these are the well-known wormholes supported by phantom scalar field. Further duality rotations remove the scalar field to yield less well known vacuum metrics of the oblate Zipoy-Voorhees-Weyl class, which describe ring wormholes. The ring encircles the wormhole throat and can have any radius, whereas its tension is always negative and should be less than $-c^4/4G$. If the tension reaches the maximal value, the geometry becomes exactly flat, but the topology remains non-trivial and corresponds to two copies of Minkowski space glued together along the disk encircled by the ring. The geodesics are straight lines, and those which traverse the ring get to the other universe. The ring therefore literally produces a whole in space. Such wormholes could perhaps be created by negative energies concentrated in toroidal volumes...

  11. 49 CFR 376.22 - Exemption for private carrier leasing and leasing between authorized carriers.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 5 2010-10-01 2010-10-01 false Exemption for private carrier leasing and leasing... MOTOR CARRIER SAFETY REGULATIONS LEASE AND INTERCHANGE OF VEHICLES Exemptions for the Leasing Regulations § 376.22 Exemption for private carrier leasing and leasing between authorized carriers....

  12. CYCLIC CODES OVER FORMAL POWER SERIES RINGS

    Institute of Scientific and Technical Information of China (English)

    Dougherty Steven T.; Liu Hongwei

    2011-01-01

    In this article, cyclic codes and negacyclic codes over formal power series rings are studied. The structure of cyclic codes over this class of rings is given, and the relationship between these codes and cyclic codes over finite chain rings is obtained. Using an isomorphism between cyclic and negacyclic codes over formal power series rings, the structure of negacyclic codes over the formal power series rings is obtained.

  13. Plasticity and beyond microstructures, crystal-plasticity and phase transitions

    CERN Document Server

    Hackl, Klaus

    2014-01-01

    The book presents the latest findings in experimental plasticity, crystal plasticity, phase transitions, advanced mathematical modeling of finite plasticity and multi-scale modeling. The associated algorithmic treatment is mainly based on finite element formulations for standard (local approach) as well as for non-standard (non-local approach) continua and for pure macroscopic as well as for directly coupled two-scale boundary value problems. Applications in the area of material design/processing are covered, ranging from grain boundary effects in polycrystals and phase transitions to deep-drawing of multiphase steels by directly taking into account random microstructures.

  14. Low-cost carriers fare competition effect

    OpenAIRE

    Carmona Benitez, R.B.; Lodewijks, G.

    2010-01-01

    This paper examines the effects that low-cost carriers (LCC’s) produce when entering new routes operated only by full-service carriers (FSC’s) and routes operated by low-cost carriers in competition with full-service carriers. A mathematical model has been developed to determine what routes should be operated by a low-cost carrier with better possibilities to subsist. The proposed model in this paper was set up by analyzing The United States domestic air transport market 2005 year database fr...

  15. Carrier synchronization for STBC OFDM systems

    Institute of Scientific and Technical Information of China (English)

    Cai Jueping; Song Wentao; Li Zan; Ge Jianhua

    2005-01-01

    All-digital carrier synchronization strategies and algorithms for space-time block coding (STBC) orthogonal frequency division multiplexing (OFDM) are proposed in this paper. In our scheme, the continuous pilots (CP) are saved, and the complexity of carrier synchronization is reduced significantly by dividing the process into three steps. The coarse carrier synchronization and the fine carrier synchronization algorithms are investigated and analyzed in detail. Simulations show that the carrier can be locked into tracking mode quickly, and the residual frequency error satisfies the system requirement in both stationary and mobile environments.

  16. Deterioration of bioplastic carrier bags in the environment and assessment of a new recycling alternative.

    Science.gov (United States)

    Accinelli, Cesare; Saccà, Maria Ludovica; Mencarelli, Mariangela; Vicari, Alberto

    2012-09-01

    Increasing environmental concerns and the introduction of technologies based on renewable resources have stimulated the replacement of persistent petroleum-derived plastics with biodegradable plastics from biopolymers. As a consequence, a variety of products are currently manufactured from bioplastic, including carrier bags. This series of studies investigated the deterioration of carrier bags made with Mater-Bi (MB), a starch-based bioplastic, in soil, compost and two aquatic ecosystems, a littoral marsh and seawater. Results from the laboratory study indicated that bioplastic carrier bags were rapidly deteriorated in soil and compost. After three months of incubation, weight loss of specimens was of 37% and 43% in soil and compost, respectively. Conversely, little deterioration was observed in specimens buried in soil under field conditions or exposed to water of a littoral marsh and of the Adriatic Sea. These findings were consistent with the greater number of bacteria and especially fungi capable of degrading MB that were recovered from soil and compost with respect to the two aquatic ecosystems. Considering that a variety of microbial isolates are capable of using MB as a source of carbon, a new alternative to recycle these MB-based carrier bags was explored. More specifically, starchy residues from bags were fermented by the fungus Rhizopus oryzae to produce up to 35 mg of lactic acid per g of bag residues.

  17. International policies to reduce plastic marine pollution from single-use plastics (plastic bags and microbeads): A review.

    Science.gov (United States)

    Xanthos, Dirk; Walker, Tony R

    2017-02-18

    Marine plastic pollution has been a growing concern for decades. Single-use plastics (plastic bags and microbeads) are a significant source of this pollution. Although research outlining environmental, social, and economic impacts of marine plastic pollution is growing, few studies have examined policy and legislative tools to reduce plastic pollution, particularly single-use plastics (plastic bags and microbeads). This paper reviews current international market-based strategies and policies to reduce plastic bags and microbeads. While policies to reduce microbeads began in 2014, interventions for plastic bags began much earlier in 1991. However, few studies have documented or measured the effectiveness of these reduction strategies. Recommendations to further reduce single-use plastic marine pollution include: (i) research to evaluate effectiveness of bans and levies to ensure policies are having positive impacts on marine environments; and (ii) education and outreach to reduce consumption of plastic bags and microbeads at source.

  18. Traversable wormholes the Roman ring

    CERN Document Server

    Visser, M

    1997-01-01

    In this brief report I introduce a yet another class of geometries for which semi-classical chronology protection theorems are of dubious physical reliability. I consider a ``Roman ring'' of traversable wormholes, wherein a number of wormholes are arranged in a ring in such a manner that no subset of wormholes is near to chronology violation, though the combined system can be arbitrarily close to chronology violation. I show that (with enough wormholes in the ring) the gravitational vacuum polarization (the expectation value of the quantum stress-energy tensor) can be made arbitrarily small. In particular the back-reaction can be kept arbitrarily small all the way to the ``reliability horizon''---so that semi-classical quantum gravity becomes unreliable before the gravitational back reaction becomes large.

  19. Non-permeable substrate carrier for electroplating

    Energy Technology Data Exchange (ETDEWEB)

    Abas, Emmanuel Chua; Chen, Chen-An; Ma, Diana Xiaobing; Ganti, Kalyana Bhargava

    2012-11-27

    One embodiment relates to a substrate carrier for use in electroplating a plurality of substrates. The substrate carrier comprises a non-conductive carrier body on which the substrates are to be held. Electrically-conductive lines are embedded within the carrier body, and a plurality of contact clips are coupled to the electrically-conductive lines embedded within the carrier body. The contact clips hold the substrates in place and electrically couple the substrates to the electrically-conductive lines. The non-conductive carrier body is continuous so as to be impermeable to flow of electroplating solution through the non-conductive carrier body. Other embodiments, aspects and features are also disclosed.

  20. Non-permeable substrate carrier for electroplating

    Energy Technology Data Exchange (ETDEWEB)

    Abas, Emmanuel Chua; Chen, Chen-an; Ma, Diana Xiaobing; Ganti, Kalyana; Divino, Edmundo Anida; Ermita, Jake Randal G.; Capulong, Jose Francisco S.; Castillo, Arnold Villamor

    2015-12-29

    One embodiment relates to a substrate carrier for use in electroplating a plurality of substrates. The substrate carrier comprises a non-conductive carrier body on which the substrates are to be held. Electrically-conductive lines are embedded within the carrier body, and a plurality of contact clips are coupled to the electrically-conductive lines embedded within the carrier body. The contact clips hold the substrates in place and electrically couple the substrates to the electrically-conductive lines. The non-conductive carrier body is continuous so as to be impermeable to flow of electroplating solution through the non-conductive carrier body. Other embodiments, aspects and features are also disclosed.

  1. Tree rings and radiocarbon calibration

    Energy Technology Data Exchange (ETDEWEB)

    Barbetti, M. [University of Sydney, Sydney, NSW (Australia). NWG Macintosh Centre for Quaternary Dating

    1999-11-01

    Only a few kinds of trees in Australia and Southeast Asia are known to have growth rings that are both distinct and annual. Those that do are therefore extremely important to climatic and isotope studies. In western Tasmania, extensive work with Huon pine (Lagarostrobos franklinii) has shown that many living trees are more than 1,000 years old, and that their ring widths are sensitive to temperature, rainfall and cloud cover (Buckley et al. 1997). At the Stanley River there is a forest of living (and recently felled) trees which we have sampled and measured. There are also thousands of subfossil Huon pine logs, buried at depths less than 5 metres in an area of floodplain extending over a distance of more than a kilometre with a width of tens of metres. Some of these logs have been buried for 50,000 years or more, but most of them belong to the period between 15,000 years and the present. In previous expeditions in the 1980s and 1990s, we excavated and sampled about 350 logs (Barbetti et al. 1995; Nanson et al. 1995). By measuring the ring-width patterns, and matching them between logs and living trees, we have constructed a tree-ring dated chronology from 571 BC to AD 1992. We have also built a 4254-ring floating chronology (placed by radiocarbon at ca. 3580 to 7830 years ago), and an earlier 1268-ring chronology (ca. 7,580 to 8,850 years ago). There are many individuals, or pairs of logs which match and together span several centuries, at 9,000 years ago and beyond 15 refs., 1 tab., 1 fig.

  2. Occurrence of polycyclic aromatic hydrocarbons (PAHs in beached plastic pellets from Mumbai coast, India

    Directory of Open Access Journals (Sweden)

    HB Jayasiri

    2014-06-01

    Full Text Available PAHs are a class of ubiquitous pollutants which consist of two or more fused benzene rings in various arrangements. A number of PAH compounds are known carcinogens and bioaccumulate and biomagnify. These compounds originate naturally as well as anthropogenically through oil spills, incineration of waste and combustion of fossil fuels and wood. The environmental consequence of Plastic pellets is the sorption organic pollutants on their surface from the sea surface microlayer (SML where the hydrophobic contaminants are known to be enriched. The plastic pellets were collected along the recent high tide line from four beaches of Mumbai coast bimonthly during May 2011 - March 2012. A total of 72 pools of plastic pellets were extracted, fractionated and analysed by Gas Chromatograph coupled to a mass spectrometer to evaluate the extent and sources of 16 PAHs. The mean ΣPAH concentration in pellets was 9202.30±114.89 ng g-1 with a wide range (35.4-46191.58 ng g-1. The concentration of fluorene was found to be the highest (1606.30±251.54 ng g-1 followed by anthracene, chrysene and phenanthrene. The ΣPAH concentration was significantly varied among months and there was no significant difference among sites at  p=0.05. The 2-3 aromatic ring compounds accounted for 60% of the total PAHs in pellets of Mumbai coast while 4 rings and 5-6 rings compounds accounted for 26 and 14%, respectively. The ratio of low and high molecular weight PAHs indicated that the contamination by petrogenic sources was predominant over the pyrogenic ones in plastic pellets suggesting oil pollution in coastal area of Mumbai.Keywords: plastic pellets, PAHs, Mumbai, sources

  3. On Simple-Injective Rings

    Institute of Scientific and Technical Information of China (English)

    W.K. Nicholson; Jae Keol Park; M.F. Yousif

    2002-01-01

    A ring R is called right simple-injective if every R-linear map from a right ideal of R to R with simple image can be extended to R. It is shown that a right simple-injective ring R is quasi-Frobenius if R is right Goldie with essential right socle, or R is left perfect and the right annihilator of k ∈ R is finitely generated whenever kR or Rk is simple. This extends a result of Bjork.

  4. On Ideals of Regular Rings

    Institute of Scientific and Technical Information of China (English)

    CHEN Huan Yin; LI Fu An

    2002-01-01

    In this paper, we investigate ideals of regular rings and give several characterizations for an ideal to satisfy the comparability. In addition, it is shown that, if Ⅰ is a minimal two-sided ideal of a regular ring R, then Ⅰ satisfies the comparability if and only if Ⅰ is separative. Furthermore, we prove that, for ideals with stable range one, Roth's problem has an affirmative solution. These extend the corresponding results on unit-regularity and one-sided unit-regularity.

  5. Nanoscale nonlinear PANDA ring resonator

    CERN Document Server

    Yupapin, Preecha

    2012-01-01

    Microring/nanoring resonator is an interesting device that has been widely studied and investigated by researchers from a variety of specializations. This book begins with the basic background of linear and nonlinear ring resonators. A novel design of nano device known as a PANDA ring resonator is proposed. The use of the device in the form of a PANDA in applications such as nanoelectronics, measurement, communication, sensors, optical and quantum computing, drug delivery, hybrid transistor and a new concept of electron-hole pair is discussed in detail.

  6. Laparoscopic appendicectomy using endo-ring applicator and fallope rings

    Directory of Open Access Journals (Sweden)

    Ali Iyoob

    2009-01-01

    Full Text Available Background/Aim: Wider adoption of laparoscopic appendicectomy (LA is limited by problems in securing the appendiceal base as well as the cost and the duration compared with the open procedure. The objective of this study was to assess the feasibility and efficacy of a new method for securing the appendiceal base in LA, so as to make the entire procedure simpler and cheaper, and hence, more popular. Methods: Twenty-five patients who were candidates for appendicectomy (emergency as well as elective and willing for the laparoscopic procedure were selected for this study. Ports used were 10 mm at the umbilicus, 5 mm at the lower right iliac fossa, and 10 mm at the left iliac fossa. Extremely friable, ruptured, or turgid organs of diameters larger than 8 mm were excluded from the study. The mesoappendix was divided close to the appendix by diathermy. Fallope rings were applied to the appendiceal base using a special ring applicator, and the appendix was divided and extracted through the lumen of the applicator. Results: The procedure was successful in 23 (92% cases, and the mean duration of the procedure was 20 minutes (15-32 minutes. There were no procedural complications seen during a median follow-up of two weeks. The equipment and rings were cheaper when compared with that of the standard methods of securing the base of the appendix. Conclusion: LA using fallope rings is a safe, simple, easy-to-learn, and economically viable method.

  7. ring i Praksis: Praksis i Læring

    DEFF Research Database (Denmark)

    Kjær, Malene

    2015-01-01

    I denne artiklen er empirien hentet fra et dansk sykehus der en sykepleiestudent skal gis tilgang til en bestemt fagkultur ved hjelp av den erfarne sykepleierens multimodale opplæringsform. I analysen vises, at ord, blikk, positur, berøring – alt inngår i en følsom samhandlingssituasjon der det o...

  8. Phenotypic plasticity, costs of phenotypes, and costs of plasticity

    DEFF Research Database (Denmark)

    Callahan, Hilary S; Maughan, Heather; Steiner, Uli

    2008-01-01

    Why are some traits constitutive and others inducible? The term costs often appears in work addressing this issue but may be ambiguously defined. This review distinguishes two conceptually distinct types of costs: phenotypic costs and plasticity costs. Phenotypic costs are assessed from patterns...... of covariation, typically between a focal trait and a separate trait relevant to fitness. Plasticity costs, separable from phenotypic costs, are gauged by comparing the fitness of genotypes with equivalent phenotypes within two environments but differing in plasticity and fitness. Subtleties associated with both...... types of costs are illustrated by a body of work addressing predator-induced plasticity. Such subtleties, and potential interplay between the two types of costs, have also been addressed, often in studies involving genetic model organisms. In some instances, investigators have pinpointed the mechanistic...

  9. At What Cost a Carrier?

    Science.gov (United States)

    2013-03-01

    brushed At What Cost a Carrier?M A R C H 2 0 1 3 4 | with interest, consequently pushing to convert the coal supply ship Jupiter into an American aircra...began to pay o!. By 1999 only 4 tons of bombs were needed to accomplish the mission, regardless of the weather at the target. Couple this fact with...there, how many bombs does it drop? | 7 #e &rst fact that needs to be understood in answer- ing these questions is that piloting an aircra" onto the

  10. Wuestite - a solar energy carrier

    Energy Technology Data Exchange (ETDEWEB)

    Weidenkaff, A.; Nueesch, P.; Wokaun, A. [Paul Scherrer Inst. (PSI), Villigen (Switzerland); Reller, A. [Hamburg Univ., Hamburg (Germany)

    1997-06-01

    Hydrogen is produced when Wuestite (Fe{sub 1-y}O) is oxidised by water. This reaction is part of a two-step thermochemical metal oxide cycle for the storage of solar energy in the form of chemical energy carriers, characterised by a high chemical potential. The reaction was studied in a tubular furnace with on-line gas analysis and further characterised in detail by DTA und high-temperature X-ray powder diffraction. The influence of non-stoichiometry, morphology and temperature on the mechanism and kinetics of the water-splitting reaction was determined. (author) 3 figs., tabs., 3 refs.

  11. Hydrogen - A sustainable energy carrier

    Directory of Open Access Journals (Sweden)

    Kasper T. Møller

    2017-02-01

    Full Text Available Hydrogen may play a key role in a future sustainable energy system as a carrier of renewable energy to replace hydrocarbons. This review describes the fundamental physical and chemical properties of hydrogen and basic theories of hydrogen sorption reactions, followed by the emphasis on state-of-the-art of the hydrogen storage properties of selected interstitial metallic hydrides and magnesium hydride, especially for stationary energy storage related utilizations. Finally, new perspectives for utilization of metal hydrides in other applications will be reviewed.

  12. Biodegradable plastics from renewable sources.

    Science.gov (United States)

    Flieger, M; Kantorová, M; Prell, A; Rezanka, T; Votruba, J

    2003-01-01

    Plastic waste disposal is a huge ecotechnological problem and one of the approaches to solving this problem is the development of biodegradable plastics. This review summarizes data on their use, biodegradability, commercial reliability and production from renewable resources. Some commercially successful biodegradable plastics are based on chemical synthesis (i.e. polyglycolic acid, polylactic acid, polycaprolactone, and polyvinyl alcohol). Others are products of microbial fermentations (i.e. polyesters and neutral polysaccharides) or are prepared from chemically modified natural products (e.g., starch, cellulose, chitin or soy protein).

  13. Plastics recycling: challenges and opportunities

    OpenAIRE

    Hopewell, Jefferson; Dvorak, Robert; Kosior, Edward

    2009-01-01

    Plastics are inexpensive, lightweight and durable materials, which can readily be moulded into a variety of products that find use in a wide range of applications. As a consequence, the production of plastics has increased markedly over the last 60 years. However, current levels of their usage and disposal generate several environmental problems. Around 4 per cent of world oil and gas production, a non-renewable resource, is used as feedstock for plastics and a further 3–4% is expended to pro...

  14. Circadian Regulation of Synaptic Plasticity

    Directory of Open Access Journals (Sweden)

    Marcos G. Frank

    2016-07-01

    Full Text Available Circadian rhythms refer to oscillations in biological processes with a period of approximately 24 h. In addition to the sleep/wake cycle, there are circadian rhythms in metabolism, body temperature, hormone output, organ function and gene expression. There is also evidence of circadian rhythms in synaptic plasticity, in some cases driven by a master central clock and in other cases by peripheral clocks. In this article, I review the evidence for circadian influences on synaptic plasticity. I also discuss ways to disentangle the effects of brain state and rhythms on synaptic plasticity.

  15. PLASMA GASIFICATION OF WASTE PLASTICS

    Directory of Open Access Journals (Sweden)

    Tadeusz Mączka

    2013-01-01

    Full Text Available The article presents the process of obtaining liquid fuels and fuel gas in the process of plasma processing of organic materials, including waste plastics. The concept of plasma pyrolysis of plastics was presented and on its basis a prototype installation was developed. The article describes a general rule of operating the installation and its elements in the process and basic operation parameters determined during its start-up. Initial results of processing plastics and the directions further investigations are also discussed. The effect of the research is to be the design of effective technology of obtaining fuels from gasification/pyrolysis of organic waste and biomass.

  16. 78 FR 66801 - Motor Carrier Safety Advisory Committee; Charter Renewal

    Science.gov (United States)

    2013-11-06

    ... Federal Motor Carrier Safety Administration Motor Carrier Safety Advisory Committee; Charter Renewal AGENCY: Federal Motor Carrier Safety Administration (FMCSA), DOT. ACTION: Announcement of advisory... Committee that provides the Agency with advice and recommendations on motor carrier safety programs...

  17. Recycling of Reinforced Plastics

    Science.gov (United States)

    Adams, R. D.; Collins, Andrew; Cooper, Duncan; Wingfield-Digby, Mark; Watts-Farmer, Archibald; Laurence, Anna; Patel, Kayur; Stevens, Mark; Watkins, Rhodri

    2014-02-01

    This work has shown is that it is possible to recycle continuous and short fibre reinforced thermosetting resins while keeping almost the whole of the original material, both fibres and matrix, within the recyclate. By splitting, crushing hot or cold, and hot forming, it is possible to create a recyclable material, which we designate a Remat, which can then be used to remanufacture other shapes, examples of plates and tubes being demonstrated. Not only can remanufacturing be done, but it has been shown that over 50 % of the original mechanical properties, such as the E modulus, tensile strength, and interlaminar shear strength, can be retained. Four different forms of composite were investigated, a random mat Glass Fibre Reinforced Plastic (GFRP) bathroom component and boat hull, woven glass and carbon fibre cloth impregnated with an epoxy resin, and unidirectional carbon fibre pre-preg. One of the main factors found to affect composite recyclability was the type of resin matrix used in the composite. Thermoset resins tested were shown to have a temperature range around the Glass Transition Temperature (Tg) where they exhibit ductile behaviour, hence aiding reforming of the material. The high-grade carbon fibre prepreg was found to be less easy to recycle than the woven of random fibre laminates. One method of remanufacturing was by heating the Remat to above its glass transition temperature, bending it to shape, and then cooling it. However, unless precautions are taken, the geometric form may revert. This does not happen with the crushed material.

  18. A Experimental Study of Viscous Vortex Rings.

    Science.gov (United States)

    Dziedzic, Mauricio

    Motivated by the role played by vortex rings in the process of turbulent mixing, the work is focused on the problem of stability and viscous decay of a single vortex ring. A new classification is proposed for vortex rings which is based on extensive hot-wire measurements of velocity in the ring core and wake and flow visualization. Vortex rings can be classified as laminar, wavy, turbulence-producing, and turbulent. Prediction of vortex ring type is shown to be possible based on the vortex ring Reynolds number. Linear growth rates of ring diameter with time are observed for all types of vortex rings, with different growth rates occurring for laminar and turbulent vortex rings. Data on the viscous decay of vortex rings are used to provide experimental confirmation of the accuracy of Saffman's equation for the velocity of propagation of a vortex ring. Experimental data indicate that instability of the vortex ring strongly depends on the mode of generation and can be delayed by properly adjusting the generation parameters. A systematic review of the literature on vortex-ring interactions is presented in the form of an appendix, which helps identify areas in which further research may be fruitful.

  19. Microbial colonization and degradation of polyethylene and biodegradable plastic bags in temperate fine-grained organic-rich marine sediments.

    Science.gov (United States)

    Nauendorf, Alice; Krause, Stefan; Bigalke, Nikolaus K; Gorb, Elena V; Gorb, Stanislav N; Haeckel, Matthias; Wahl, Martin; Treude, Tina

    2016-02-15

    To date, the longevity of plastic litter at the sea floor is poorly constrained. The present study compares colonization and biodegradation of plastic bags by aerobic and anaerobic benthic microbes in temperate fine-grained organic-rich marine sediments. Samples of polyethylene and biodegradable plastic carrier bags were incubated in natural oxic and anoxic sediments from Eckernförde Bay (Western Baltic Sea) for 98 days. Analyses included (1) microbial colonization rates on the bags, (2) examination of the surface structure, wettability, and chemistry, and (3) mass loss of the samples during incubation. On average, biodegradable plastic bags were colonized five times higher by aerobic and eight times higher by anaerobic microbes than polyethylene bags. Both types of bags showed no sign of biodegradation during this study. Therefore, marine sediment in temperate coastal zones may represent a long-term sink for plastic litter and also supposedly compostable material.

  20. Applications of KinetiSol dispersing for the production of plasticizer free amorphous solid dispersions.

    Science.gov (United States)

    DiNunzio, James C; Brough, Chris; Miller, Dave A; Williams, Robert O; McGinity, James W

    2010-06-14

    Thermal manufacturing methods for the production of solid dispersions frequently require the addition of a plasticizer in order to achieve requisite molten material flow properties when processed by unit operations such as hot melt extrusion. KinetiSol Dispersing, a rapid high energy thermal manufacturing process, was investigated for the ability to produce amorphous solid dispersions without the aid of a plasticizer. For this study itraconazole was used as a model active ingredient, while Eudragit L100-55 and Carbomer 974P were used as model solid dispersion carriers. Triethyl citrate (TEC) was used as necessary as a model plasticizer. Compositions prepared by KinetiSol Dispersing and hot melt extrusion were evaluated for solid state properties, supersaturated in vitro dissolution behavior under pH change conditions and accelerated stability performance. Results showed that both manufacturing processes were capable of producing amorphous solid dispersions, however compositions produced by hot melt extrusion required the presence of TEC and yielded a glass transition temperature (T(g)) of approximately 54 degrees C. Plasticized and unplasticized compositions were successfully produced by KinetiSol Dispersing, with plasticizer free solid dispersions exhibiting a T(g) of approximately 101 degrees C. Supersaturated in vitro dissolution testing revealed a significantly higher dissolution rate of plasticized material which was attributed to the pore forming behavior of TEC during the acidic phase of testing. A further contribution to release may also have been provided by the greater diffusivity in the plasticized polymer. X-ray diffraction testing revealed that under accelerated stability conditions, plasticized compositions exhibited partial recrystallization, while plasticizer free materials remained amorphous throughout the 6-month testing period. These results demonstrated that KinetiSol Dispersing could be used for the production of amorphous solid dispersions

  1. Dynamic fragmentation of Al-W granular rings with different mesostructures

    Science.gov (United States)

    Chiu, Po-Hsun; Olney, Karl L.; Benson, David J.; Braithwaite, Chris; Collins, Adam; Nesterenko, Vitali F.

    2017-01-01

    Explosively driven fragmentation mechanisms of Al-W particulate composite rings were investigated. The effect of mesostructures (particulate Al and W, particulate Al and W fibers) and bonding between Al particles (processing via cold isostatic and cold isostatic + hot isostatic pressing) were determined. The kinematics of the expansion process was monitored using Photon Doppler Velocimetry measurements of the velocity of the outer surface of the rings. Numerical simulations of the expansion velocity of rings were in agreement with experimental data. Agglomerated fragments larger than sizes of initial Al particles were observed in experiments. The characteristic size of these agglomerates is most likely determined by the spacing between W inclusions. The simulations show that the dynamically expanded rings had clusters of particulates between shear bands (developing into macrocracks), which expand without significant plastic deformation, generating agglomerated fragments with sizes larger than initial Al particles, as observed in experiments. It was also demonstrated that debris has a measurable fraction of particles with sizes below the original particle sizes. The mesostructure of the fragments demonstrated that Al particles were heavily deformed within the regions having locally high strain plastic flow, which may result in fragments sizes below initial Al particle diameter. Simulations agree with experiments in that Al particles between neighboring W particles/fibers are heavily plastically deformed in comparison with Al particles away from W inclusions. Simulations also demonstrated that increasing initial porosity increases the plastic straining of Al particles between W particles/fibers. Thus, initial porosity may cause an increase in temperature of the Al fragments and cracking their surface oxide layers, therefore increasing the chance of subsequent rapid oxidation in air.

  2. SELF-DUAL PERMUTATION CODES OVER FORMAL POWER SERIES RINGS AND FINITE PRINCIPAL IDEAL RINGS

    Institute of Scientific and Technical Information of China (English)

    张光辉; 刘宏伟

    2013-01-01

    In this paper, we study self-dual permutation codes over formal power series rings and finite principal ideal rings. We first give some results on the torsion codes associated with the linear codes over formal power series rings. These results allow for obtaining some conditions for non-existence of self-dual permutation codes over formal power series rings. Finally, we describe self-dual permutation codes over finite principal ideal rings by examining permutation codes over their component chain rings.

  3. Carrier Bulk-Lifetime Measurements

    Directory of Open Access Journals (Sweden)

    M. Solcansky

    2012-01-01

    Full Text Available For the measurement of the minority carrier bulk-lifetime the characterization method MW-PCD is used, where the result of measurement is the effective carrier lifetime, which is very dependent on the surface recombination velocity and therefore on the quality of a silicon surface passivation. This work deals with an examination of a different solution types for the chemical passivation of a silicon surface. Various solutions are tested on silicon wafers for their consequent comparison. The main purpose is to find optimal solution, which suits the requirements of a time stability and start-up velocity of passivation, reproducibility of the measurements and a possibility of a perfect cleaning of a passivating solution remains from a silicon surface, so that the parameters of a measured silicon wafer will not worsen and there will not be any contamination of the other wafers series in the production after a repetitive return of the measured wafer into the production process. The cleaning process itself is also a subject of a development.

  4. Plasticity and creep of metals

    CERN Document Server

    Rusinko, Andrew

    2011-01-01

    Here is a systematic presentation of the postulates, theorems and principles of mathematical theories of plasticity and creep in metals, and their applications. Special attention is paid to analysis of the advantages and shortcomings of the classical theories.

  5. American Society of Plastic Surgeons

    Science.gov (United States)

    ... PRS PRS GO PSN PSEN GRAFT Contact Us Cosmetic Surgery New procedures and advanced technologies offer plastic surgery ... David Berman MD 14 Pidgeon Hill Drive Berman Cosmetic Surgery & S... Sterling, VA 20165 Website Franklin Richards MD Suite ...

  6. Plastic deformation of nanocrystalline nickel

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    A high-resolution electron microscopy study has uncovered the plastic behavior of accommodating large strains in nanocrystalline (NC) Ni subject to cold rolling at liquid nitrogen temperature. The activation of grain-boundary-mediated-plasticity is evidenced in NC-Ni, including twinning and formation of stacking fault via partial dislocation slips from the grain boundary. The formation and storage of 60? full dislocations are observed inside NC-grains. The grain/twin boundaries act as the barriers of dislocation slips, leading to dislocation pile-up, severe lattice distortion, and formation of sub-grain boundary. The vicinity of grain/twin boundary is where defects preferentially accumulate and likely the favorable place for onset of plastic deformation. The present results indicate the heterogeneous and multiple natures of accommodating plastic strains in NC-grains.

  7. Plastic deformation of nanocrystalline nickel

    Institute of Scientific and Technical Information of China (English)

    WU XiaoLei

    2009-01-01

    A high-resolution electron microscopy study has uncovered the plastic behavior of accommodating large strains in nanocrystalline(NC)Ni subject to cold rolling at liquid nitrogen temperature.The acti vation of grain-boundary-mediated-plasticity is evidenced in NC-Ni,including twinning and formation of stacking fault via partial dislocation slips from the grain boundary.The formation and storage of 60° full dislocations are observed inside NC-grains.The grain/twin boundaries act as the barriers of dislocation slips,leading to dislocation pile-up,severe lattice distortion,and formation of sub-grain boundary.The vicinity of grain/twin boundary is where defects preferentially accumulate and likely the favorable place for onset of plastic deformation.The present results indicate the heterogeneous and multiple natures of accommodating plastic strains in NC-grains.

  8. Exceptional plasticity of silicon nanobridges

    Energy Technology Data Exchange (ETDEWEB)

    Ishida, Tadashi; Sato, Takaaki; Toshiyoshi, Hiroshi; Collard, Dominique; Fujita, Hiroyuki [University of Tokyo, Institute of Industrial Science, 4-6-1 Komaba Meguro, Tokyo 153-8505 (Japan); Cleri, Fabrizio [Institut d' Electronique Microelectronique et Nanotechnologie (CNRS UMR 8520), Universite de Lille I, Avenue Poincare BP60069 59652 Villeneuve d' Ascq (France); Kakushima, Kuniyuki [Tokyo Institute of Technology, 4259, Nagatsuda, Midori, Yokohama, Kanagawa 226-8502 (Japan); Mita, Makoto [Department of Spacecraft Engineering, Japan Aerospace Exploration Agency, 3-1-1, Yoshinodai, Sagamihara, Kanagawa 229-8510 (Japan); Miyata, Masaki; Itamura, Noriaki; Sasaki, Naruo [Department of Materials and Life Sciences, Seikei University, 3-3-1, Kitamachi, Kichijoji, Musashino, Tokyo 180-8633 (Japan); Endo, Junji, E-mail: tadashii@iis.u-tokyo.ac.jp [FK Optical laboratory, 1-13-4 Nakano Niiza Saitama, 352-0005 (Japan)

    2011-09-02

    The plasticity of covalently bonded materials is a subject at the forefront of materials science, bearing on a wide range of technological and fundamental aspects. However, covalent materials fracture in a brittle manner when the deformation exceeds just a few per cent. It is predicted that a macroscopically brittle material like silicon can show nanoscale plasticity. Here we report the exceptional plasticity observed in silicon nanocontacts ('nanobridges') at room temperature using a special experimental setup combining a transmission electron microscope and a microelectromechanical system. When accounting for surface diffusion, we succeeded in elongating the nanocontact into a wire-like structure, with a fivefold increase in volume, up to more than twenty times the original length. Such a large plasticity was caused by the stress-assisted diffusion and the sliding of the intergranular, amorphous-like material among the nanocrystals.

  9. Globally Oriented Chinese Plastics Industry

    Institute of Scientific and Technical Information of China (English)

    Liao Zhengpin

    2004-01-01

    @@ Through continued endeavor and persistent opening to the whole world the Chinese plastics industry has been developed into a comprehensive industrial system that forms the basic material industries side by side with the steel, cement and the timber industry.

  10. Silicon ball grid array chip carrier

    Science.gov (United States)

    Palmer, David W.; Gassman, Richard A.; Chu, Dahwey

    2000-01-01

    A ball-grid-array integrated circuit (IC) chip carrier formed from a silicon substrate is disclosed. The silicon ball-grid-array chip carrier is of particular use with ICs having peripheral bond pads which can be reconfigured to a ball-grid-array. The use of a semiconductor substrate such as silicon for forming the ball-grid-array chip carrier allows the chip carrier to be fabricated on an IC process line with, at least in part, standard IC processes. Additionally, the silicon chip carrier can include components such as transistors, resistors, capacitors, inductors and sensors to form a "smart" chip carrier which can provide added functionality and testability to one or more ICs mounted on the chip carrier. Types of functionality that can be provided on the "smart" chip carrier include boundary-scan cells, built-in test structures, signal conditioning circuitry, power conditioning circuitry, and a reconfiguration capability. The "smart" chip carrier can also be used to form specialized or application-specific ICs (ASICs) from conventional ICs. Types of sensors that can be included on the silicon ball-grid-array chip carrier include temperature sensors, pressure sensors, stress sensors, inertia or acceleration sensors, and/or chemical sensors. These sensors can be fabricated by IC processes and can include microelectromechanical (MEM) devices.

  11. Ringing phenomenon in silica microspheres

    Institute of Scientific and Technical Information of China (English)

    Chunhua Dong; Changling Zou; Jinming Cui; Yong Yang; Zhengfu Han; Guangcan Guo

    2009-01-01

    Whispering gallery modes in silica microspheres are excited by a tunable continuous-wave laser through the fiber taper. Ringing phenomenon can be observed with high frequency sweeping speed. The thermal nonlinearity in the microsphere can enhance this phenomenon. Our measurement results agree very well with the theoretical predictions by the dynamic equation.

  12. Characteristic of Rings. Prime Fields

    Directory of Open Access Journals (Sweden)

    Schwarzweller Christoph

    2015-12-01

    Full Text Available The notion of the characteristic of rings and its basic properties are formalized [14], [39], [20]. Classification of prime fields in terms of isomorphisms with appropriate fields (ℚ or ℤ/p are presented. To facilitate reasonings within the field of rational numbers, values of numerators and denominators of basic operations over rationals are computed.

  13. The Lord of the Rings

    Institute of Scientific and Technical Information of China (English)

    潘金梅

    2002-01-01

    Peter Jackson's first film in The Lord of the Rings trilogy (三步曲) has just grabbed (夺得) four Oscars-awards for the best make-up, best cinematography (摄影), best visual effects and best original score.Chinese audience had a chance to watch the fihn from late April.

  14. Fusion rings and fusion ideals

    DEFF Research Database (Denmark)

    Andersen, Troels Bak

    by the so-called fusion ideals. The fusion rings of Wess-Zumino-Witten models have been widely studied and are well understood in terms of precise combinatorial descriptions and explicit generating sets of the fusion ideals. They also appear in another, more general, setting via tilting modules for quantum...

  15. E-læring

    DEFF Research Database (Denmark)

    Heilesen, Simon

    2001-01-01

    E-læring er et modeord og et mantra. Undervisning bliver ikke automatisk bedre af, at der sættes et ”e-” foran. Forbedring og fornyelse af undervisningen er betinget af, at vi forstår computermediets muligheder og skaber forandring ved at tilpasse det til de undervisningsformer, vi ønsker....

  16. Exercises in modules and rings

    CERN Document Server

    Lam, TY

    2009-01-01

    This volume offers a compendium of exercises of varying degree of difficulty in the theory of modules and rings. All exercises are solved in full detail. Each section begins with an introduction giving the general background and the theoretical basis for the problems that follow.

  17. Livslang læring

    DEFF Research Database (Denmark)

    Larson, Anne

    2016-01-01

    Pædagogisk sociologi beskæftiger sig blandt andet med de politiske rammebetingelser for opdragelse, undervisning, socialisering og uddannelse. I dette kapitel præsenteres en komparativ undersøgelse af EU’s politik med hensyn til livslang læring på den ene side, og den danske politik og lovgivning...

  18. Counting problems for number rings

    NARCIS (Netherlands)

    Brakenhoff, Johannes Franciscus

    2009-01-01

    In this thesis we look at three counting problems connected to orders in number fields. First we study the probability that for a random polynomial f in Z[X] the ring Z[X]/f is the maximal order in Q[X]/f. Connected to this is the probability that a random polynomial has a squarefree discriminant. T

  19. Near rings, fuzzy ideals, and graph theory

    CERN Document Server

    Satyanarayana, Bhavanari

    2013-01-01

    Near Rings, Fuzzy Ideals, and Graph Theory explores the relationship between near rings and fuzzy sets and between near rings and graph theory. It covers topics from recent literature along with several characterizations. After introducing all of the necessary fundamentals of algebraic systems, the book presents the essentials of near rings theory, relevant examples, notations, and simple theorems. It then describes the prime ideal concept in near rings, takes a rigorous approach to the dimension theory of N-groups, gives some detailed proofs of matrix near rings, and discusses the gamma near

  20. Cascaded uncoupled dual-ring modulator

    CERN Document Server

    Gu, Tingyi; Wong, Chee Wei; Dong, Po

    2014-01-01

    We demonstrate that by coherent driving two uncoupled rings in same direction, the effective photon circulating time in the dual ring modulator is reduced, with increased modulation quality. The inter-ring detuning dependent photon dynamics, Q-factor, extinction ratio and optical modulation amplitude of two cascaded silicon ring resonators are studied and compared with that of a single ring modulator. Experimentally measured eye diagrams, together with coupled mode theory simulations, demonstrate the enhancement of dual ring configuration at 20 Gbps with a Q ~ 20,000.

  1. Investigation of Air-Liquid Interface Rings in Buffer Preparation Vessels: the Role of Slip Agents.

    Science.gov (United States)

    Shi, Ting; Ding, Wei; Kessler, Donald W; De Mas, Nuria; Weaver, Douglas G; Pathirana, Charles; Martin, Russell D; Mackin, Nancy A; Casati, Michael; Miller, Scott A; Pla, Itzcoatl A

    2016-01-01

    Air-liquid interface rings were observed on the side walls of stainless steel buffer vessels after certain downstream buffer preparations. Those rings were resistant to regular cleaning-in-place procedures but could be removed by manual means. To investigate the root cause of this issue, multiple analytical techniques, including liquid chromatography with tandem mass spectrometry detection (LC-MS/MS), high-resolution accurate mass liquid chromatography with mass spectrometry, nuclear magnetic resonance, Fourier transform infrared spectroscopy, and scanning electron microscopy with energy-dispersive X-ray spectroscopy have been employed to characterize the chemical composition of air-liquid interface rings. The main component of air-liquid interface rings was determined to be slip agents, and the origin of the slip agents can be traced back to their presence on raw material packaging liners. Slip agents are commonly used in plastic industry as additives to reduce the coefficient of friction during the manufacturing process of thin films. To mitigate this air-liquid interface ring issue, an alternate liner with low slip agent was identified and implemented with minimal additional cost. We have also proactively tested the packaging liners of other raw materials currently used in our downstream buffer preparation to ensure slip agent levels are appropriate. Air-liquid interface rings were observed on the side walls of stainless steel buffer vessels after certain downstream buffer preparations. To investigate the root cause of this issue, multiple analytical techniques have been employed to characterize the chemical composition of air-liquid interface rings. The main components of air-liquid interface rings were determined to be slip agents, which are common additives used in the manufacturing process of thin films. The origin of the slip agents can be traced back to their presence on certain raw material packaging liners. To mitigate this air-liquid interface ring

  2. Computational materials science: Nanoscale plasticity

    DEFF Research Database (Denmark)

    Jacobsen, Karsten Wedel; Schiøtz, Jakob

    2002-01-01

    How does plastic deformation of polycrystalline materials with grain sizes less than 100 nm look at the atomic scale? A large-scale molecular dynamics simulation of nanocrystalline alluminium reveals some surprising behaviour.......How does plastic deformation of polycrystalline materials with grain sizes less than 100 nm look at the atomic scale? A large-scale molecular dynamics simulation of nanocrystalline alluminium reveals some surprising behaviour....

  3. Sorting Techniques for Plastics Recycling

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    This paper presents the basic principles of three different types of separating methods and a general guideline for choosing the most effective method for sorting plastic mixtures. It also presents the results of the tests carried out for separation of PVC, ABS and PET from different kinds of plastic mixtures in order to improve the grade of the raw input used in mechanical or feedstock recycling.

  4. [Modern neuroimaging of brain plasticity].

    Science.gov (United States)

    Kasprian, G; Seidel, S

    2010-02-01

    Modern neuroimaging methods offer new insights into the plasticity of the human brain. As the techniques of functional MRI and diffusion tensor imaging are increasingly being applied in a clinical setting, the examiner is now frequently confronted with the interpretation of imaging findings related to regenerative processes in response to lesions of the central and also of the peripheral nervous system. In this article individual results of modern neuroimaging studies are discussed in the context of structural and functional plasticity of the CNS.

  5. Plastic bronchitis: a management challenge.

    Science.gov (United States)

    Eberlein, Michael H; Drummond, Michael B; Haponik, Edward F

    2008-02-01

    Plastic bronchitis is an uncommon and underdiagnosed entity, characterized by recurrent expectoration of large, branching bronchial casts. We describe a 39-year-woman with no prior lung disease who had episodic wheezing, severe dyspnea with expectoration of large and thick secretions, branching in appearance, which she described as resembling squid. A comprehensive evaluation revealed no specific cause and a diagnosis of idiopathic plastic bronchitis was made. In plastic bronchitis the bronchial casts may vary in size from small segmental casts of a bronchus to casts filling the airways of an entire lung. Plastic bronchitis can therefore present as an acute life-threatening emergency if mechanical obstruction of major airways occurs. The casts are differentiated into type I, inflammatory casts, or type II, acellular casts. The type I inflammatory casts are often associated with bronchial disease and often have an acute presentation. The acellular type of cast production is often chronic or recurrent. Numerous systemic illnesses are associated with plastic bronchitis, but often, as in our patient, no underlying cause can be identified. The treatment of plastic bronchitis includes acute therapy to aid the removal and expectoration of casts, and specific short- or long-term treatments attempting to address the underlying hypersecretory process. The therapeutic options are supported only by anecdotal evidence based on case reports as the rarity and heterogeneity of plastic bronchitis confounds systematic investigations of its treatment. Improved understanding of the regulation of mucus production may allow for new treatment options in plastic bronchitis and other chronic lung diseases characterized by hypersecretion of mucus.

  6. High-Speed Ring Bus

    Science.gov (United States)

    Wysocky, Terry; Kopf, Edward, Jr.; Katanyoutananti, Sunant; Steiner, Carl; Balian, Harry

    2010-01-01

    The high-speed ring bus at the Jet Propulsion Laboratory (JPL) allows for future growth trends in spacecraft seen with future scientific missions. This innovation constitutes an enhancement of the 1393 bus as documented in the Institute of Electrical and Electronics Engineers (IEEE) 1393-1999 standard for a spaceborne fiber-optic data bus. It allows for high-bandwidth and time synchronization of all nodes on the ring. The JPL ring bus allows for interconnection of active units with autonomous operation and increased fault handling at high bandwidths. It minimizes the flight software interface with an intelligent physical layer design that has few states to manage as well as simplified testability. The design will soon be documented in the AS-1393 standard (Serial Hi-Rel Ring Network for Aerospace Applications). The framework is designed for "Class A" spacecraft operation and provides redundant data paths. It is based on "fault containment regions" and "redundant functional regions (RFR)" and has a method for allocating cables that completely supports the redundancy in spacecraft design, allowing for a complete RFR to fail. This design reduces the mass of the bus by incorporating both the Control Unit and the Data Unit in the same hardware. The standard uses ATM (asynchronous transfer mode) packets, standardized by ITU-T, ANSI, ETSI, and the ATM Forum. The IEEE-1393 standard uses the UNI form of the packet and provides no protection for the data portion of the cell. The JPL design adds optional formatting to this data portion. This design extends fault protection beyond that of the interconnect. This includes adding protection to the data portion that is contained within the Bus Interface Units (BIUs) and by adding to the signal interface between the Data Host and the JPL 1393 Ring Bus. Data transfer on the ring bus does not involve a master or initiator. Following bus protocol, any BIU may transmit data on the ring whenever it has data received from its host. There

  7. New insights into protein secretion: TANGO1 runs rings around the COPII coat.

    Science.gov (United States)

    Glick, Benjamin S

    2017-04-03

    In this issue, Liu et al. (2017. J. Cell Biol. https://doi.org/10.1083/jcb.201611088) and Raote et al. (2017. J. Cell Biol. https://doi.org/10.1083/jcb.201608080) use super-resolution microscopy to visualize large COPII-coated endoplasmic reticulum (ER) export carriers. Rings of TANGO1 surround COPII, implicating TANGO1 in organizing ER exit sites and in regulating COPII coat dynamics and geometry.

  8. Oscillator strength reduction induced by external electric fields in self-assembled quantum dots and rings

    OpenAIRE

    2007-01-01

    We have carried out continuous wave and time resolved photoluminescence experiments in self-assembled In(Ga)As quantum dots and quantum rings embedded in field effect structure devices. In both kinds of nanostructures, we find a noticeable increase of the exciton radiative lifetime with the external voltage bias that must be attributed to the field-induced polarizability of the confined electron hole pair. The interplay between the exciton radiative recombination and the electronic carrier tu...

  9. ARE PLASTIC GROCERY BAGS SACKING THE ENVIRONMENT?

    OpenAIRE

    Mangal Gogte

    2009-01-01

    This paper is oriented on analysis impacts of plastic bags on environment. In this paper is analyzed did plastic bags are so harmful, and what are the main ingredients of it. One part of this paper is oriented on effects of plastic bags and management of their usage. There is also made comparative analysis between impacts of plastic and paper bags on environment.

  10. Experiments with elasto-plastic oscillator

    DEFF Research Database (Denmark)

    Randrup-thomsen, Søren; Ditlevsen, Ove Dalager

    1996-01-01

    Plastic displacements of a Gaussian white noise excited three degrees of freedom non-ideal elasto-plastic oscillator are measured in laboratory experiments and the plastic displacements are compared to computer simulated results for the corresponding ideal elasto-plastic oscillator. The comparative...

  11. Experiments with elasto-plastic oscillator

    DEFF Research Database (Denmark)

    Randrup-Thomsen, S.; Ditlevsen, Ove Dalager

    1999-01-01

    Plastic displacements of a Gaussian white noise excited three degrees of freedom non-ideal elasto-plastic oscillator are measured in laboratory experiments and the plastic displacements are compared to computer simulated results for the corresponding ideal elasto-plastic oscillator. The comparative...

  12. 49 CFR 192.281 - Plastic pipe.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Plastic pipe. 192.281 Section 192.281... Plastic pipe. (a) General. A plastic pipe joint that is joined by solvent cement, adhesive, or heat fusion may not be disturbed until it has properly set. Plastic pipe may not be joined by a threaded joint...

  13. 49 CFR 192.59 - Plastic pipe.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Plastic pipe. 192.59 Section 192.59 Transportation... BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Materials § 192.59 Plastic pipe. (a) New plastic pipe... specification; and (2) It is resistant to chemicals with which contact may be anticipated. (b) Used plastic...

  14. The Story of the Plastics Industry.

    Science.gov (United States)

    Masson, Don, Ed.

    This is an illustrated informative booklet, designed to serve members of the Society of the Plastics Industry, Inc., and the plastics industry as a whole. It provides basic information about the industry's history and growth, plastics raw materials, typical uses of plastics, properties, and methods of processing and fabricating. (Author/DS)

  15. Differential Analysis of the Nasal Microbiome of Pig Carriers or Non-Carriers of Staphylococcus aureus

    DEFF Research Database (Denmark)

    Espinosa-Gongora, Carmen; Larsen, Niels; Schonning, Kristian;

    2016-01-01

    pathogen in animal carriers. The aim of this study was to determine whether the nasal microbiome of pig S. aureus carriers differs from that of non-carriers. The V3-V5 region of the 16S rRNA gene was sequenced from nasal swabs of 44 S. aureus carriers and 56 non-carriers using the 454 GS FLX titanium...... microbiome of pigs that are not colonized with S. aureus harbours several species/taxa that are significantly less abundant in pig carriers, suggesting that the nasal microbiota may play a role in the individual predisposition to S. aureus nasal carriage in pigs. Further research is warranted to isolate...

  16. Carriers of the astronomical 2175 ? extinction feature

    Energy Technology Data Exchange (ETDEWEB)

    Bradley, J; Dai, Z; Ernie, R; Browning, N; Graham, G; Weber, P; Smith, J; Hutcheon, I; Ishii, H; Bajt, S; Floss, C; Stadermann, F

    2004-07-20

    The 2175 {angstrom} extinction feature is by far the strongest spectral signature of interstellar dust observed by astronomers. Forty years after its discovery the origin of the feature and the nature of the carrier remain controversial. The feature is enigmatic because although its central wavelength is almost invariant its bandwidth varies strongly from one sightline to another, suggesting multiple carriers or a single carrier with variable properties. Using a monochromated transmission electron microscope and valence electron energy-loss spectroscopy we have detected a 5.7 eV (2175 {angstrom}) feature in submicrometer-sized interstellar grains within interplanetary dust particles (IDPs) collected in the stratosphere. The carriers are organic carbon and amorphous silicates that are abundant and closely associated with one another both in IDPs and in the interstellar medium. Multiple carriers rather than a single carrier may explain the invariant central wavelength and variable bandwidth of the astronomical 2175 {angstrom} feature.

  17. Impact of carriers in oral absorption

    DEFF Research Database (Denmark)

    Gram, Luise Kvisgaard; Rist, Gerda Marie; Lennernäs, Hans

    2009-01-01

    (APP) was not described by carrier kinetics. However, glipizide is affecting exsorption for ES, due to interactions on basolateral carrier. The study confirms that estrone-3-sulfate can be used to characterize anionic carrier kinetics. Furthermore it is suggested that estrone-3-sulfate may be used to identify compounds......Carriers may mediate the permeation across enterocytes for drug substances being organic anions. Carrier mediated permeation for the organic anions estrone-3-sulfate (ES) and glipizide across Caco-2 cells were investigated kinetically, and interactions on involved carriers evaluated. Initial...... uptakes (P(UP)) at apical and basolateral membranes, apparent permeabilities (P(APP)) and corresponding intracellular end-point accumulations (P(EPA)) of radioactive labeled compounds were studied. Possible effects of other anionic compounds were investigated. Apical P(UP) and absorptive P(APP) for ES...

  18. Ultrafast carriers dynamics in filled-skutterudites

    Energy Technology Data Exchange (ETDEWEB)

    Guo, Liang; Xu, Xianfan, E-mail: xxu@purdue.edu [School of Mechanical Engineering and Birck Nanotechnology Center, Purdue University, West Lafayette, Indiana 47907 (United States); Salvador, James R. [Chemical and Materials Systems Laboratory, GM Global R and D, Warren, Michigan 48090 (United States)

    2015-06-08

    Carrier dynamics of filled-skutterudites, an important class of thermoelectric materials, is investigated using ultrafast optical spectroscopy. By tuning the wavelength of the probe laser, charge transfers at different electronic energy levels are interrogated. Analysis based on the Kramers-Kronig relation explains the complex spectroscopy data, which is mainly due to band filling caused by photo-excited carriers and free carrier absorption. The relaxation time of hot carriers is found to be about 0.4–0.6 ps, depending on the electronic energy level, and the characteristic time for carrier-phonon equilibrium is about 0.95 ps. These studies of carrier dynamics, which fundamentally determines the transport properties of thermoelectric material, can provide guidance for the design of materials.

  19. Ultrafast carriers dynamics in filled-skutterudites

    Science.gov (United States)

    Guo, Liang; Xu, Xianfan; Salvador, James R.

    2015-06-01

    Carrier dynamics of filled-skutterudites, an important class of thermoelectric materials, is investigated using ultrafast optical spectroscopy. By tuning the wavelength of the probe laser, charge transfers at different electronic energy levels are interrogated. Analysis based on the Kramers-Kronig relation explains the complex spectroscopy data, which is mainly due to band filling caused by photo-excited carriers and free carrier absorption. The relaxation time of hot carriers is found to be about 0.4-0.6 ps, depending on the electronic energy level, and the characteristic time for carrier-phonon equilibrium is about 0.95 ps. These studies of carrier dynamics, which fundamentally determines the transport properties of thermoelectric material, can provide guidance for the design of materials.

  20. Synchronous phase demodulation algorithm for conic carrier Hartmann topographer

    Science.gov (United States)

    Gonzalez, Adonai; Rivera, Mariano; Servin, Manuel; Legarda-Saenz, Ricardo; Dalmau, Oscar; Martinez, Amalia

    2015-04-01

    In this paper, a theoretical analysis of a new algorithm for measuring phase objects (PO) is presented. The algorithm analyses images captured with a modified Hartmann plate. The proposed method demodulates a signal with a conic-wavefront carrier by using synchronous interferometric techniques. Typically a Hartmann plate is a mask with an array of holes, the proposal is to replace those holes with a series of circular concentric rings created by a conic carrier, named Conic Hartmann plate mask (CHM). The proposed algorithm computes a dense correspondence between the pattern source and its interferogram on the PO. This dense correspondence is computed as the phase change of the refracted waveform with respect to the reference one. This approach is more robust than standard techniques that computes the center of each spot in order to estimate its position; which involves pattern recognition and segmentation tasks, something normal in a typical Hartmann test. We show in this work that the new method overcomes different problems such as irregular background illumination, spots overlapping with pupil border and spots matching due to rapid changes on the surface slopes. This work shows a general procedure for radial derivatives integration based on base functions. As far as the authors know, the here presented demonstration has not been reported before. In particular, we show that Zernike polynomials are suitable for PO. Numerical experiments with real and simulated data demonstrate the algorithm performance.

  1. Deformation mechanisms of plasticized starch materials.

    Science.gov (United States)

    Mikus, P-Y; Alix, S; Soulestin, J; Lacrampe, M F; Krawczak, P; Coqueret, X; Dole, P

    2014-12-19

    The aim of this paper is to understand the influence of plasticizer and plasticizer amount on the mechanical and deformation behaviors of plasticized starch. Glycerol, sorbitol and mannitol have been used as plasticizers. After extrusion of the various samples, dynamic mechanical analyses and video-controlled tensile tests have been performed. It was found that the nature of plasticizer, its amount as well as the aging of the material has an impact on the involved deformation mechanism. The variations of volume deformation could be explained by an antiplasticization effect (low plasticizer amount), a phase-separation phenomenon (excess of plasticizer) and/or by the retrogradation of starch.

  2. The Canarias Einstein Ring: a Newly Discovered Optical Einstein Ring

    CERN Document Server

    Bettinelli, Margherita; Aparicio, Antonio; Hidalgo, Sebastian L; Cassisi, Santi; Walker, Alistair R; Piotto, Giampaolo; Valdes, Frank

    2016-01-01

    We report the discovery of an optical Einstein Ring in the Sculptor constellation, IAC J010127-334319, in the vicinity of the Sculptor Dwarf Spheroidal Galaxy. It is an almost complete ring ($\\sim 300^{\\circ}$) with a diameter of $\\sim 4.5\\, {\\rm arcsec}$. The discovery was made serendipitously from inspecting Dark Energy Camera (DECam) archive imaging data. Confirmation of the object nature has been obtained by deriving spectroscopic redshifts for both components, lens and source, from observations at the $10.4$ m Gran Telescopio CANARIAS (GTC) with the spectrograph OSIRIS. The lens, a massive early-type galaxy, has a redshift of ${\\rm z}=0.581$ while the source is a starburst galaxy with redshift of ${\\rm z}=1.165$. The total enclosed mass that produces the lensing effect has been estimated to be ${\\rm M_{tot}=(1.86 \\pm 0.23) \\,\\cdot 10^{12}\\, {\\rm M_{\\odot}}}$.

  3. Evolution of phenotypic plasticity in colonizing species.

    Science.gov (United States)

    Lande, Russell

    2015-05-01

    I elaborate an hypothesis to explain inconsistent empirical findings comparing phenotypic plasticity in colonizing populations or species with plasticity from their native or ancestral range. Quantitative genetic theory on the evolution of plasticity reveals that colonization of a novel environment can cause a transient increase in plasticity: a rapid initial increase in plasticity accelerates evolution of a new optimal phenotype, followed by slow genetic assimilation of the new phenotype and reduction of plasticity. An association of colonization with increased plasticity depends on the difference in the optimal phenotype between ancestral and colonized environments, the difference in mean, variance and predictability of the environment, the cost of plasticity, and the time elapsed since colonization. The relative importance of these parameters depends on whether a phenotypic character develops by one-shot plasticity to a constant adult phenotype or by labile plasticity involving continuous and reversible development throughout adult life. © 2014 John Wiley & Sons Ltd.

  4. New Dimensions of Moving Bed Biofilm Carriers

    OpenAIRE

    Piculell, Maria

    2016-01-01

    The moving bed biofilm reactor (MBBR) is a biological wastewater treatment process in which microorganisms grow as biofilms on suspended carriers. Conventionally, MBBRs are mainly designed and optimized based on the carrier surface area, neglecting the dynamic relationship between carrier design, reactor operation and biofilm characteristics, such as biofilm thickness and the composition of the microbial community. The purpose of this research project was to learn more about the roles of the ...

  5. Carriers by chemical vapor deposition

    Science.gov (United States)

    Mronga, Norbert; Adel, J.; Czech, Erwin

    1990-07-01

    Printed materials are affecting people's lives in a variety of ways and to a constantly increasing extent, both in the private and in the business spheres. In particular, the predicted reduction of printed materials resulting from electronic data processing - the so-called "paperless electronic office" - has not occured, indeed quite the reverse. In recent years electrophotographic reprography has established itself successfully as a competitor to conventional printing processes. In the office a photocopier is now a part of the standard equipment. Because of BASF's traditional intensive involvement with pigments and colored printing inks its interest in new technologies in these areas is especially great. BASF has therefore been engaged in research on carriers for some years now.

  6. Stable rings generated by their units

    Directory of Open Access Journals (Sweden)

    Huanyin Chen

    2001-01-01

    Full Text Available We introduce the class of rings satisfying (m,1-stable range and investigate equivalent characterizations of such rings. These give generalizations of the corresponding results by Badawi (1994, Ehrlich (1976, and Fisher and Snider (1976.

  7. How to Remove a Stuck Ring Safely

    Science.gov (United States)

    ... Gardening Safety Turkey Carving Removing a Ring Español Artritis de la base del pulgar Dedo en gatillo ... Gardening Safety Turkey Carving Removing a Ring Español Artritis de la base del pulgar Dedo en gatillo ...

  8. On π-regularity of General Rings

    Institute of Scientific and Technical Information of China (English)

    CHEN WEI-XING; CUI SHU-YING

    2010-01-01

    A general ring means an associative ring with or without identity. An idempotent e in a general ring I is called left (right) semicentral if for every x∈ I,xe = exe (ex = exe). And I is called semiabelian ff every idempotent in I is left or right semicentral. It is proved that a semiabelian general ring I is π-regular if and only ff the set N(I) of nilpotent elements in I is an ideal of I and I/N(I) is regular. It follows that if I is a semiabelian general ring and K is an ideal of I,then I is π-regular if and only if both K and I/K are r-regular. Based on this we prove that every semiabelian GVNL-ring is an SGVNL-ring. These generalize several known results on the relevant subject. Furthermore we give a characterization of a semiabelian GVNL-ring.

  9. International Tree Ring Data Bank (ITRDB)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Tree ring data from the International Tree Ring Data Bank and World Data Center for Paleoclimatology archives. Data include raw treering measurements (most are...

  10. Experiments with vortex rings in air

    Science.gov (United States)

    Hernández, R. H.; Cibert, B.; Béchet, C.

    2006-09-01

    We report quantitative experimental measurements of the instability of vortex rings generated in air. Vortex rings are created by pushing air through the circular orifice of a cylindrical cavity with a flat piston driven by a loudspeaker. Hot-wire anemometry provides accurate measurements of the velocity profile at all stages of the ring formation including stable and unstable rings. Flow visualization using a laser light sheet shows that the initially undisturbed vortex ring is progressively deformed in the azimuthal direction giving rise to a wavy azimuthal and periodic pattern in the circumference of the ring. The wavy pattern is steady, i.e., it does not rotate or translate during the ring's motion. However as the vortex motion progresses in the axial direction, the displaced portions of the ring are convected away from the initial undisturbed position and the wavy pattern grows with local Reynolds number.

  11. Persistent currents in normal metal rings.

    Science.gov (United States)

    Bluhm, Hendrik; Koshnick, Nicholas C; Bert, Julie A; Huber, Martin E; Moler, Kathryn A

    2009-04-03

    The authors have measured the magnetic response of 33 individual cold mesoscopic gold rings, one ring at a time. The response of some sufficiently small rings has a component that is periodic in the flux through the ring and is attributed to a persistent current. Its period is close to h/e, and its sign and amplitude vary between rings. The amplitude distribution agrees well with predictions for the typical h/e current in diffusive rings. The temperature dependence of the amplitude, measured for four rings, is also consistent with theory. These results disagree with previous measurements of three individual metal rings that showed a much larger periodic response than expected. The use of a scanning SQUID microscope enabled in situ measurements of the sensor background. A paramagnetic linear susceptibility and a poorly understood anomaly around a zero field are attributed to defect spins.

  12. Towards a theory for the Uranian rings

    Science.gov (United States)

    Goldreich, P.; Tremaine, S.

    1979-01-01

    Interparticle collisions, radiation drag, and differential precession all tend to disrupt the rings of Uranus. The first two effects lead to radial spreading which would disrupt a free ring in less than or approximately 100,000,000 yr. It is proposed that the rings are confined in radius by gravitational torques from a series of small satellites that orbit with the ring system. Differential precession tends to destroy the apse alignment of the elliptical epsilon ring. It is suggested that apse alignment is maintained by the self-gravity of the ring. The resulting mass of the epsilon ring is approximately 5 times 10 to the 18th power g. Its radial confinement requires (for example) a pair of satellites of mass approximately 10 to the 19th power g, in circular orbits roughly 500 km away on either side of the ring

  13. Kernel representations for behaviors over finite rings

    NARCIS (Netherlands)

    Kuijper, M.; Pinto, R.; Polderman, J.W.; Yamamoto, Y.

    2006-01-01

    In this paper we consider dynamical systems finite rings. The rings that we study are the integers modulo a power of a given prime. We study the theory of representations for such systems, in particular kernel representations.

  14. The Structure of gr-simple Rings

    Institute of Scientific and Technical Information of China (English)

    朱彬

    2003-01-01

    A characterization of gr-simple rings is given by using the notion of componentwise-dense subrings of a full matrix ring over a division ring. As a conse-quence, any G-graded full matrix ring over a division ring is isomorphic to a dense subring of a full matrix ring with a good G-grading. Some conditions for a grading of a full matrix ring to be isomorphic to a good one are given, which generalize some results in: Dáscáscu, S., Lon, B., Niǎstǎsescu, C. and Montes, J. R., Group gradingson full matrix rings, J. Algebra, 220(1999), 709-728.

  15. On Splitting Rings for Azumaya Skew Polynomial Rings

    Institute of Scientific and Technical Information of China (English)

    George Szeto; Lianyong Xue

    2001-01-01

    Let B be a ring with 1, p an automorphism of B of order n for some integer n, and B[x; p] the skew polynomial ring in x over B such that 1, x,x2,... ,xn-1 are independent over B and xn ∈ U(Bp), where Bp is the set of elements in B fixed under p and U(Bρ) is the set of all units in Bρ. Let -ρ be the inner automorphism of B[x; p] induced by x. Assume n is a unit in B. It is shown that, for a -ρ-Galois extension B[x; p] over (B[x; ρ])-ρ (resp., a DeMeyer-Kanzaki Galois extention B over Bp), B[x; ρ] is Azumaya if and only if (B[x; ρ])-ρ (resp.,B) is Azumaya, and some splitting rings of B[x; ρ], (B[x; ρ])-ρ and B coincide.

  16. Enhanced bioremediation of PAH-contaminated soil by immobilized bacteria with plant residue and biochar as carriers

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Baoliang; Yuan, Miaoxin; Qian, Linbo [Zhejiang Univ., Hangzhou (China). Dept. of Environmental Science; Zhejiang Provincial Key Laboratory of Organic Pollution Process and Control, Hangzhou (China)

    2012-10-15

    Polycyclic aromatic hydrocarbons (PAHs) are largely accumulated in soils in China. The immobilized-microorganism technique (IMT) is a potential approach for abating soil contamination with PAHs. However, few studies about the application of IMT to contaminated soil remediation were reported. Due to recalcitrance to decomposition, biochar application to soil may enhance soil carbon sequestration, but few studies on the application of biochars to remediation of contaminated soil were reported. In this study, we illustrated enhanced bioremediation of soil having a long history of PAH contamination by IMT using plant residues and biochars as carriers. Two PAH-degrading bacteria, Pseudomonas putida and an unidentified indigenous bacterium, were selected for IMT. The extractability and biodegradation of 15 PAHs in solution and an actual PAH-contaminated soil amended with immobilized-bacteria materials were investigated under different incubation periods. The effects of carriers and the molecular weight of PAHs on bioremediation efficiency were determined to illustrate their different bio-dissipation mechanisms of PAHs in soil. The IMT can considerably enhance the removal of PAHs. Carriers impose different effects on PAH bio-dissipation by amended soil with immobilized-bacteria, which can directly degrade the carrier-associated PAHs. The removal of PAHs from soil depended on PAH molecular weight and carrier types. Enhanced bio-dissipation by IMT was much stronger for 4- and 5-ring PAHs than for 3- and 6-ring ones in soil. Only P400 biochar-immobilized bacteria enhanced bio-dissipation of all PAHs in contaminated soil after a 90-day incubation. Biochar can promote bioremediation of contaminated soil as microbial carriers of IMT. It is vital to select an appropriate biochar as an immobilized carrier to stimulate biodegradation. It is feasible to use adsorption carriers with high sorptive capabilities to concentrate PAHs as well as microorganisms and thereby enhance

  17. Liner surface improvements for low friction piston ring packs

    Science.gov (United States)

    Anderberg, C.; Dimkovski, Z.; Rosén, B.-G.

    2014-01-01

    The development of engine components in the automotive industry is governed by several constraints such as environmental legislation and customer expectations. About a half of the frictional losses in an internal combustion engine come from the interactions between the piston assembly and cylinder liner surface. The tribological considerations in the contact between the piston ring and cylinder liner have attracted much attention over the past few decades. Many non-conventional cylinder liner finishes have been, and are being, developed with the aim to reduce friction losses and oil consumption, but the effects of the surface finish on piston ring pack performance is not well understood. One way of reducing friction in the cylinder system is to reduce the tangential load from the piston ring pack, focusing on the oil control ring. However, the side-effect of this is a disappointingly increased oil consumption. In this study a number of different cylinder liner surface specifications were developed and implemented in test engines with the aim of maintaining the level for oil consumption when decreasing the tangential load for the piston ring pack. To improve our understanding of the result, the same surfaces were evaluated in elastic and elasto-plastic rough contact and hydrodynamic flow simulation models. It is shown that oil consumption is strongly related to surface texture on the cylinder liners and at lower speeds (900-1200 rpm), a ‘rougher surface’ with a high core (e.g. Sk) and valley roughness (e.g. Svk) results in higher oil consumption. At the medium speed range (1200-3600 rpm), oil consumption continues to dominate for the ‘rough’ surfaces but with a visible influence of a lower oil consumption for a decreased roughness within the ‘rough’ surface group. ‘Smooth’ surfaces with a ‘smooth’ core (Sk), irrespective of the valley component (Svk), show similar oil consumption. For engine speeds above 3600 rpms, an increase in plateau

  18. Nonlinear analysis of ring oscillator circuits

    KAUST Repository

    Ge, Xiaoqing

    2010-06-01

    Using nonlinear systems techniques, we analyze the stability properties and synchronization conditions for ring oscillator circuits, which are essential building blocks in digital systems. By making use of its cyclic structure, we investigate local and global stability properties of an n-stage ring oscillator. We present a sufficient condition for global asymptotic stability of the origin and obtain necessity if the ring oscillator consists of identical inverter elements. We then give a synchronization condition for identical interconnected ring oscillators.

  19. Dysphagia due to Multiple Esophageal Rings

    Directory of Open Access Journals (Sweden)

    Stephen N Sullivan

    1995-01-01

    Full Text Available A 27-year-old Saudi man with dysphagia due to multiple esophageal rings is reported and the literature reviewed. Dysphagia due to multiple esophageal rings is very rare. Only 15 cases have been reported. The patient is usually male and has had dysphagia for many years when presenting. The cause of the rings is unknown. Theories to explain dysphagia are that the rings are either congenital or an unusual manifestation of gastroesophageal reflux.

  20. Polar ring galaxies formation and properties

    CERN Document Server

    Bournaud, F; Bournaud, Frederic; Combes, Francoise

    2003-01-01

    Formation scenarios for polar ring galaxies are studied through N-body simulatio ns that are compared with existing observations. It is shown that polar rings ar e likely to be formed by tidal accretion of the polar material from a gas rich d onor galaxy. The distribution of dark matter in polar ring galaxies is studied: dark halos seem to be flattened towards the polar rings.

  1. Plastic neutron detectors.

    Energy Technology Data Exchange (ETDEWEB)

    Wilson, Tiffany M.S; King, Michael J.; Doty, F. Patrick

    2008-12-01

    photoresponse with increasing stretch ratio. Other additives examined, including small molecules and cosolvents, did not cause any significant increase in photoresponse. Finally, we discovered an inverse-geometric particle track effect wherein increased track lengths created by tilting the detector off normal incidence resulted in decreased signal collection. This is interpreted as a trap-filling effect, leading to increased carrier mobility along the particle track direction. Estimated collection efficiency along the track direction was near 20 electrons/micron of track length, sufficient for particle counting in 50 micron thick films.

  2. Impact of field limiting ring technique on breakdown voltage of irradiated Si sensors

    CERN Document Server

    Bhardwaj, Ashutosh; Jha Manoj, Kr; Kumar, Ashish; Ranjan, Kirti; Shivpuri, RK; Srivastava-Ajay, K

    2003-01-01

    The very intense radiation environment of high luminosity future colliding beam experiments (like LHC) makes radiation hardness the most important issue for Si detectors. One of the central issues concerning all LHC experiments is the breakdown performance of these detectors. The major macroscopic effect of radiation damage in determining the viability of long-term operation of Si sensors is the change in effective charge carrier concentration (N //e//f//f), leading to type-inversion. Floating field limiting guard rings have been established as means of improving the breakdown performance of Si detectors. In this work the usefulness of the guard rings in improving the breakdown performance of detectors after type-inversion has been studied. Simulations are carried out to study the effect of change in N//e//f//f on the breakdown performance of optimized guard ring structure using two dimensional device simulation program, TMA- MEDICI. Detailed calculations using Hamburg Model have allowed the parameterization ...

  3. Impact of field limiting ring technique on breakdown voltage of irradiated Si sensors

    CERN Document Server

    Bhardwaj, A; Namrata, S; Chatterji, S; Srivastava-Ajay, K; Kumar, A; Jha, Manoj Kumar; Shivpuri, R K

    2004-01-01

    The very intense radiation environment of high luminosity future colliding beam experiments (like LHC) makes radiation hardness the most important issue for Si detectors. One of the central issues concerning all LHC experiments is the breakdown performance of these detectors. The major macroscopic effect of radiation damage in determining the viability of long-term operation of Si sensors is the change in effective charge carrier concentration (N/sub eff/), leading to type-inversion. Floating field limiting guard rings have been established as means of improving the breakdown performance of Si detectors. In this work the usefulness of the guard rings in improving the breakdown performance of detectors after type-inversion has been studied. Simulations are carried out to study the effect of change in N/sub eff/ on the breakdown performance of optimized guard ring structure using two dimensional device simulation program, TMA- MEDICI. Detailed calculations using Hamburg Model have allowed the parameterization o...

  4. Generalized periodic and generalized Boolean rings

    Directory of Open Access Journals (Sweden)

    Howard E. Bell

    2001-01-01

    Full Text Available We prove that a generalized periodic, as well as a generalized Boolean, ring is either commutative or periodic. We also prove that a generalized Boolean ring with central idempotents must be nil or commutative. We further consider conditions which imply the commutativity of a generalized periodic, or a generalized Boolean, ring.

  5. A Ring Construction Using Finite Directed Graphs

    Science.gov (United States)

    Bardzell, Michael

    2012-01-01

    In this paper we discuss an interesting class of noncommutative rings which can be constructed using finite directed graphs. This construction also creates a vector space. These structures provide undergraduate students connections between ring theory and graph theory and, among other things, allow them to see a ring unity element that looks quite…

  6. IAG ring test animal proteins 2013

    NARCIS (Netherlands)

    Raamsdonk, van L.W.D.; Pinckaers, V.G.Z.; Scholtens-Toma, I.M.J.; Prins, T.W.; Vliege, J.J.M.

    2013-01-01

    A ring test was organized for the detection of animal proteins in animal feed by microscopy in the framework of the annual ring tests of the IAG - International Association for Feeding stuff Analysis, Section Feeding stuff Microscopy. The organizer of the the ring study was to provide the

  7. RRF Rings which are not LRF

    Indian Academy of Sciences (India)

    K Varadarajan

    2000-05-01

    Define a ring to be RRF (respectively LRF) if every right (respectively left) -module is residually finite. We determine the necessary and sufficient conditions for a formal triangular matrix ring $$T=\\begin{pmatrix}A & 0\\\\ M & B\\end{pmatrix}$$ to be RRF (respectively LRF). Using this we give examples of RRF rings which are not LRF.

  8. Familial transmission of a ring chromosome 21

    DEFF Research Database (Denmark)

    Hertz, Jens Michael

    1987-01-01

    A ring chromosome 21 was found in a phenotypically normal mother and her son. The clinical findings in the son were bilateral retention of the testes and a slightly delayed puberty onset. Consequences of a ring formation of a chromosome 21 in phenotypically normal patients are presented...... and discussed, and the previously reported cases of familially transmitted G-group ring chromosomes are reviewed....

  9. Type Ⅱ codes over finite rings

    Institute of Scientific and Technical Information of China (English)

    DOUGHERTY; Steven; T

    2010-01-01

    In this paper,we generalize the concept of Type Ⅱ codes to arbitrary finite rings. We focus on Type Ⅱ codes over finite chain rings and use the Chinese Remainder Theorem on these codes to study Type Ⅱ codes over principal ideal rings.

  10. Phase noise analysis for OFDM systems based on hot-carrier effects in synchronization electronics

    Science.gov (United States)

    Herlekar, Sameer R.; Zhang, Chi; Wu, Hsiao-Chun; Srivastava, Ashok

    2005-05-01

    Phase noise may be regarded as the most severe cause of performance degradation in OFDM systems. Hot carriers (HCs), found in the CMOS synchronization circuits, are high-mobility charge carriers that degrade the MOSFET devices" performance by increasing the threshold voltage required to operate the MOSFETs. The HC effect manifests itself as the phase noise, which increases with the continued MOSFET operation and results in the performance degradation of the Voltage-Controlled Oscillator (VCO) built on the MOSFET. The HC effect is particularly evident in the short-channel MOSFET devices. The MOSFET instability will impact on the OFDM system performance. The relationship between the OFDM system performance and the hot carrier effect can be analyzed in terms of a crucial parameter, the MOSFET threshold voltage. In this paper, we derive a general phase noise model for OFDM systems based on the Hot-carrier effect and the corresponding drifted threshold voltage in differential ring oscillators. The expected OFDM performance degradation due to the hot carrier effect is provided through our simulations. We show that the OFDM BER performance evaluation using the existing phase noise models can be upto three orders of magnitude different from the results obtained by using our phase noise model.

  11. Study of atmospheric pressure weakly ionized plasma as surface compatibilization technique for improved plastic composites loaded with cellulose based fillers

    Science.gov (United States)

    Lekobou, William Pimakouon

    Atmospheric pressure plasmas have gained considerable interest from researchers recently for their unique prospective of engineering surfaces with plasma without the need of vacuum systems. They offer the advantage of low energy consumption, minimal capital cost and their simplicity as compared to conventional low pressure plasmas make them easy to upscale from laboratory to industry size. The present dissertation summarizes results of our attempt at applying atmospheric pressure weakly ionized plasma (APWIP) to the engineering of plastic composites filled with cellulose based substrates. An APWIP reactor was designed and built based on a multipoint-to-grounded ring and screen configurations. The carrier gas was argon and acetylene serves as the precursor molecule. The APWIP reactors showed capability of depositing plasma polymerized coating rich in carbon on substrates positioned within the electrode gap as well as downstream of the plasma discharge into the afterglow region. Our findings show that films grow by forming islands which for prolonged deposition time grow into thin films showing nodules, aggregates of nodules and microspheres. They also show chemical structure similar to films deposited from hydrocarbons with other conventional plasma techniques. The plasma polymerized deposits were used on substrates to modify their surface properties. Results show the surface of wood veneer and wood flour can be finely tuned from hydrophilic to hydrophobic. It was achieved by altering the topography of the surfaces along with their chemical composition. The wettability of wood veneer was investigated with contact angle measurements on capacitive drops and the capillary effect was utilized to assess surface properties of wood flour exposed to the discharges.

  12. E-læring

    DEFF Research Database (Denmark)

    Hansbøl, Mikala

    2010-01-01

    Når der etableres forbindelser mellem uddannelse og it, så sker der forandringer af, hvad det vil sige at tale om uddannelse. Uddannelsen har måske ikke en fysisk campus. Det er heller ikke sikkert, at man behøver at gå i formel skole eller tage musiktimer hos en musiklærer ansigt-til-ansigt for ......-til-ansigt for at lære at spille guitar. E-læring eller på engelsk e-learning vil sige, at undervisningen og dermed din læring sker med it - noget som man er nødt til at tage bestik af....

  13. Behavioral Mapless Navigation Using Rings

    Science.gov (United States)

    Monroe, Randall P.; Miller, Samuel A.; Bradley, Arthur T.

    2012-01-01

    This paper presents work on the development and implementation of a novel approach to robotic navigation. In this system, map-building and localization for obstacle avoidance are discarded in favor of moment-by-moment behavioral processing of the sonar sensor data. To accomplish this, we developed a network of behaviors that communicate through the passing of rings, data structures that are similar in form to the sonar data itself and express the decisions of each behavior. Through the use of these rings, behaviors can moderate each other, conflicting impulses can be mediated, and designers can easily connect modules to create complex emergent navigational techniques. We discuss the development of a number of these modules and their successful use as a navigation system in the Trinity omnidirectional robot.

  14. Legende læring

    DEFF Research Database (Denmark)

    Holm, Claus

    2015-01-01

    Det danske dogme er, at lærere og pædagoger ikke bør blande sig i børns fri leg. Men forskningen i kreativitetspædagogik anbefaler, at lærere og pædagoger blander sig i børnenes legende læring.......Det danske dogme er, at lærere og pædagoger ikke bør blande sig i børns fri leg. Men forskningen i kreativitetspædagogik anbefaler, at lærere og pædagoger blander sig i børnenes legende læring....

  15. Fourth-generation storage rings

    Energy Technology Data Exchange (ETDEWEB)

    Galayda, J. N.

    1999-11-16

    It seems clear that a linac-driven free-electron laser is the accepted prototype of a fourth-generation facility. This raises two questions: can a storage ring-based light source join the fourth generation? Has the storage ring evolved to its highest level of performance as a synchrotrons light source? The answer to the second question is clearly no. The author thinks the answer to the first question is unimportant. While the concept of generations has been useful in motivating thought and effort towards new light source concepts, the variety of light sources and their performance characteristics can no longer be usefully summed up by assignment of a ''generation'' number.

  16. Fiber Ring Optical Gyroscope (FROG)

    Science.gov (United States)

    1979-01-01

    The design, construction, and testing of a one meter diameter fiber ring optical gyro, using 1.57 kilometers of single mode fiber, are described. The various noise components: electronic, thermal, mechanical, and optical, were evaluated. Both dc and ac methods were used. An attempt was made to measure the Earth rotation rate; however, the results were questionable because of the optical and electronic noise present. It was concluded that fiber ring optical gyroscopes using all discrete components have many serious problems that can only be overcome by discarding the discrete approach and adapting an all integrated optic technique that has the laser source, modulator, detector, beamsplitters, and bias element on a single chip.

  17. APS storage ring vacuum system

    Energy Technology Data Exchange (ETDEWEB)

    Niemann, R.C.; Benaroya, R.; Choi, M.; Dortwegt, R.J.; Goeppner, G.A.; Gonczy, J.; Krieger, C.; Howell, J.; Nielsen, R.W.; Roop, B.; Wehrle, R.B.

    1990-01-01

    The Advanced Photon Source synchrotron radiation facility, under construction at the Argonne National Laboratory, incorporates a large ring for the storage of 7 GeV positrons for the generation of photon beams for the facility's experimental program. The Storage Ring's 1104 m circumference is divided into 40 functional sectors. The sectors include vacuum, beam transport, control, acceleration and insertion device components. The vacuum system, which is designed to operate at a pressure of 1 n Torr, consists of 240 connected sections, the majority of which are fabricated from an aluminum alloy extrusion. The sections are equipped with distributed NeG pumping, photon absorbers with lumped pumping, beam position monitors, vacuum diagnostics and valving. The details of the vacuum system design, selected results of the development program and general construction plans are presented. 11 refs., 6 figs., 3 tabs.

  18. On co-semihereditary rings

    Institute of Scientific and Technical Information of China (English)

    薛卫民

    1997-01-01

    A ring R is left co-semihereditary (strongly left co-semihereditary) if every finitely cogenerated factor of a finitely cogenerated (arbitrary) injective left R-module is injective.A left co-semihereditary ring,which is not strongly left co-semihereditary,is given to answer a question of Miller and Tumidge in the negative.If RUS defines a Morita duality,R is proved to be left co-semihereditary (left semihereditary) if and only if S is right semihereditary (right co-semihereditary).Assuming that S≥R is an almost excellent extension,S is shown to be (strongly) right co-semihereditary if and only if R is (strongly) right co-semihereditary.

  19. Thermoplastic polyurethane-based intravaginal rings for prophylaxis and treatment of (recurrent) bacterial vaginosis.

    Science.gov (United States)

    Verstraete, G; Vandenbussche, L; Kasmi, S; Nuhn, L; Brouckaert, D; Van Renterghem, J; Grymonpré, W; Vanhoorne, V; Coenye, T; De Geest, B G; De Beer, T; Remon, J P; Vervaet, C

    2017-08-30

    The aim of the present study was to develop thermoplastic polyurethane (TPU)-based intravaginal rings (IVRs) for prophylaxis and treatment of bacterial vaginosis via hot melt extrusion/injection molding. Therefore, different TPU grades were processed in combination with lactic acid or metronidazole, targeting a sustained lactic acid release over a 28day-period and sustained metronidazole release over 4-7days. Hot melt extrusion of lactic acid/TPU combinations required a lower extrusion temperature due to the plasticizing properties of lactic acid, evidenced by the lower glass transition temperature (Tg) and cross-over point (Ttanδ=1) values. NIR-chemical imaging data showed a homogenous distribution of lactic acid in TPU matrices at drug loads up to 30% (w/w). The addition of metronidazole did not lower processing temperatures, as the active pharmaceutical ingredient remained crystalline in the TPU matrix. Hydrophobic TPUs with a low ratio between the soft and hard segments (SS/HS ratio) in the polymer structure were suitable carriers for the lactic acid-eluting device over a 28-day period, while hydrophilic TPUs were needed to achieve the required release rate of metronidazole-eluting IVRs. IVRs manufactured with a TPU grade having a higher SS/HS ratio and lactic acid/TPU ratio exhibited a more elastic behavior. The addition of 25% (w/w) metronidazole did not affect the mechanical properties of the IVRs. Hydrophilic TPUs were most prone to biofilm formation by Candida albicans and Staphylococcus aureus, but the incorporation of metronidazole in the device prevented biofilm formation. Based on the drug eluting performance and mechanical tests, a mixture of lactic acid and Tecoflex™ EG-93A (20/80, w/w) and a combination of metronidazole and Tecophilic™ SP-93A-100 (25/75, w/w) were selected to design IVRs for the prophylaxis and treatment of bacterial vaginosis, respectively. Slug mucosal irritation tests predicted low irritation potency for both devices

  20. Selvreguleret læring

    DEFF Research Database (Denmark)

    Pedersen, Kirsten Hyldahl

    2012-01-01

    forudsætninger. For mange lærere er differentieret undervisning dog et diffust begreb, der kan være vanskeligt at forholde sig til i praksis. I denne artikel vil jeg derfor forsøge at svare på, om der kan findes en undervisningsstrategi, der vægter selvreguleret læring som værktøj, til at differentiere...

  1. ring og it

    DEFF Research Database (Denmark)

      Antologien er et bidrag til didaktiske diskussioner om brug af f.eks. programpakker til sprogundervisning, præsentationsprogrammel og konferencesystemer på de videregående uddannelser. Antologien diskuterer ideen om, at multimediale medier og internettet kan understøtte læring, undervisning og ...... samarbejde ud fra konkrete eksempler på it-anvendelser, hvor fokus er på potentialer, barrierer og faldgruber....

  2. ring mellem elever

    DEFF Research Database (Denmark)

    Davidsen, Jacob; Georgsen, Marianne

    I denne rapport tilbyder vi et indblik i det gennemførte projekt, og forfatterne har valgt nogle forhold ud, som belyses og diskuteres, mens andre ikke berøres eller diskuteres nævneværdigt i denne rapport. Det skyldes blandt andet projektets mange facetter, som dækker både læring, teknologi, pæd...

  3. ring og it

    DEFF Research Database (Denmark)

      Antologien er et bidrag til didaktiske diskussioner om brug af f.eks. programpakker til sprogundervisning, præsentationsprogrammel og konferencesystemer på de videregående uddannelser. Antologien diskuterer ideen om, at multimediale medier og internettet kan understøtte læring, undervisning og ...... samarbejde ud fra konkrete eksempler på it-anvendelser, hvor fokus er på potentialer, barrierer og faldgruber....

  4. Smartphones and the plastic surgeon.

    Science.gov (United States)

    Al-Hadithy, Nada; Ghosh, Sudip

    2013-06-01

    Surgical trainees are facing limited training opportunities since the introduction of the European Working Time Directive. Smartphone sales are increasing and have usurped computer sales for the first time. In this context, smartphones are an important portable reference and educational tool, already in the possession of the majority of surgeons in training. Technology in the palm of our hands has led to a revolution of accessible information for the plastic surgery trainee and surgeon. This article reviews the uses of smartphones and applications for plastic surgeons in education, telemedicine and global health. A comprehensive guide to existing and upcoming learning materials and clinical tools for the plastic surgeon is included. E-books, podcasts, educational videos, guidelines, work-based assessment tools and online logbooks are presented. In the limited resource setting of modern clinical practice, savvy plastic surgeons can select technological tools to democratise access to education and best clinical care. Copyright © 2013 British Association of Plastic, Reconstructive and Aesthetic Surgeons. Published by Elsevier Ltd. All rights reserved.

  5. Mechanisms of GABAergic Homeostatic Plasticity

    Directory of Open Access Journals (Sweden)

    Peter Wenner

    2011-01-01

    Full Text Available Homeostatic plasticity ensures that appropriate levels of activity are maintained through compensatory adjustments in synaptic strength and cellular excitability. For instance, excitatory glutamatergic synapses are strengthened following activity blockade and weakened following increases in spiking activity. This form of plasticity has been described in a wide array of networks at several different stages of development, but most work and reviews have focussed on the excitatory inputs of excitatory neurons. Here we review homeostatic plasticity of GABAergic neurons and their synaptic connections. We propose a simplistic model for homeostatic plasticity of GABAergic components of the circuitry (GABAergic synapses onto excitatory neurons, excitatory connections onto GABAergic neurons, cellular excitability of GABAergic neurons: following chronic activity blockade there is a weakening of GABAergic inhibition, and following chronic increases in network activity there is a strengthening of GABAergic inhibition. Previous work on GABAergic homeostatic plasticity supports certain aspects of the model, but it is clear that the model cannot fully account for some results which do not appear to fit any simplistic rule. We consider potential reasons for these discrepancies.

  6. Mitochondria, synaptic plasticity, and schizophrenia.

    Science.gov (United States)

    Ben-Shachar, Dorit; Laifenfeld, Daphna

    2004-01-01

    The conceptualization of schizophrenia as a disorder of connectivity, i.e., of neuronal?synaptic plasticity, suggests abnormal synaptic modeling and neuronal signaling, possibly as a consequence of flawed interactions with the environment, as at least a secondary mechanism underlying the pathophysiology of this disorder. Indeed, deficits in episodic memory and malfunction of hippocampal circuitry, as well as anomalies of axonal sprouting and synapse formation, are all suggestive of diminished neuronal plasticity in schizophrenia. Evidence supports a dysfunction of mitochondria in schizophrenia, including mitochondrial hypoplasia, and a dysfunction of the oxidative phosphorylation system, as well as altered mitochondrial-related gene expression. Mitochondrial dysfunction leads to alterations in ATP production and cytoplasmatic calcium concentrations, as well as reactive oxygen species and nitric oxide production. All of the latter processes have been well established as leading to altered synaptic strength or plasticity. Moreover, mitochondria have been shown to play a role in plasticity of neuronal polarity, and studies in the visual cortex show an association between mitochondria and synaptogenesis. Finally, mitochondrial gene upregulation has been observed following synaptic and neuronal activity. This review proposes that mitochondrial dysfunction in schizophrenia could cause, or arise from, anomalies in processes of plasticity in this disorder.

  7. Polar Ring Galaxies and Warps

    Science.gov (United States)

    Combes, F.

    Polar ring galaxies, where matter is in equilibrium in perpendicular orbits around spiral galaxies, are ideal objects to probe the 3D shapes of dark matter halos. The conditions to constrain the halos are that the perpendicular system does not strongly perturb the host galaxy, or that it is possible to derive back its initial shape, knowing the formation scenario of the polar ring. The formation mechanisms are reviewed: mergers, tidal accretion, or gas accretion from cosmic filaments. The Tully-Fisher diagram for polar rings reveals that the velocity in the polar plane is higher than in the host plane, which can only be explained if the dark matter is oblate and flattened along the polar plane. Only a few individual systems have been studied in details, and 3D shapes of their haloes determined by several methods. The high frequency of warps could be explained by spontaneous bending instability, if the disks are sufficiently self-gravitating, which can put constraints on the dark matter flattening.

  8. Polar ring galaxies and warps

    CERN Document Server

    Combes, F

    2005-01-01

    Polar ring galaxies, where matter is in equilibrium in perpendicular orbits around spiral galaxies, are ideal objects to probe the 3D shapes of dark matter halos. The conditions to constrain the halos are that the perpendicular system does not strongly perturb the host galaxy, or that it is possible to derive back its initial shape, knowing the formation scenario of the polar ring. The formation mechanisms are reviewed: mergers, tidal accretion, or gas accretion from cosmic filaments. The Tully-Fisher diagram for polar rings reveals that the velocity in the polar plane is higher than in the host plane, which can only be explained if the dark matter is oblate and flattened along the polar plane. Only a few individual systems have been studied in details, and 3D shapes of their haloes determined by several methods. The high frequency of warps could be explained by spontaneous bending instability, if the disks are sufficiently self-gravitating, which can put constraints on the dark matter flattening.

  9. Macro-carriers of plastic deformation of steel surface layers detected by digital image correlation

    Energy Technology Data Exchange (ETDEWEB)

    Kopanitsa, D. G., E-mail: kopanitsa@mail.ru; Ustinov, A. M., E-mail: artemustinov@mail.ru [Tomsk State University of Architecture and Building, 2 Solyanaya Sq, Tomsk, 634003 (Russian Federation); Potekaev, A. I., E-mail: potekaev@spti.tsu.ru [National Research Tomsk State University, 36 Lenin Ave., Tomsk, 634050 (Russian Federation); Klopotov, A. A., E-mail: klopotovaa@tsuab.ru [Tomsk State University of Architecture and Building, 2 Solyanaya Sq, Tomsk, 634003 (Russian Federation); National Research Tomsk State University, 36 Lenin Ave., Tomsk, 634050 (Russian Federation); Kopanitsa, G. D., E-mail: georgy.kopanitsa@mail.com [National Research Tomsk Polytechnic University, 30 Lenin Ave., Tomsk, 634050 (Russian Federation)

    2016-01-15

    This paper presents a study of characteristics of an evolution of deformation fields in surface layers of medium-carbon low-alloy specimens under compression. The experiments were performed on the “Universal Testing Machine 4500” using a digital stereoscopic image processing system Vic-3D. A transition between stages is reflected as deformation redistribution on the near-surface layers. Electronic microscopy shows that the structure of the steel is a mixture of pearlite and ferrite grains. A proportion of pearlite is 40% and ferrite is 60%.

  10. Plastic biofilm carrier after corn cobs reduces nitrate loading in laboratory denitrifying bioreactors

    Science.gov (United States)

    Nitrate-nitrogen removal rates can be increased substantially in denitrifying bioreactors with a corn cob bed medium compared to woodchips; however, additional organic carbon (C) is released into the effluent. This laboratory column experiment was conducted to test the performance of a post-bed cha...

  11. Contraceptive vaginal ring (NuvaRing)-a novel, convenient and effective contraceptive option

    Institute of Scientific and Technical Information of China (English)

    Chen Wei-lin; Fan Guang-sheng

    2011-01-01

    Contraceptive vaginal ring (NuvaRing) is a new combined hormonal contraceptive method.Each ring contains 2.7mg ethinyl estradiol (EE) and 11.7mg etonogestrel.The ring is characteristic with its ease of use,lower EE systemic exposure and excellent cycle control.Studies have demonstrated that the efficacy and safety of the ring are equivalent to combined oral contraceptive (COC).The side effects of the ring are fewer and the biocompatibility is good.Recent studies have proved that the NuvaRing is a new,effective hormonal contraceptive option for women.

  12. 14 CFR 399.82 - Passing off of carrier identity by affiliation between carriers.

    Science.gov (United States)

    2010-01-01

    ... carrier shall not engage in joint public relations activities at points served by both carriers which tend... specified area or point, in relation to services such as the following: Solicitation and sale of passenger... name of the other carrier as to emphasize the limited role of the agent; (4) Telephone facilities at...

  13. Finite Element Optimization of Vee-ring Factor in Fine-blanking Process

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The vee-ring is one of the most characteristic features of the fine-blanking process which is derived from the conventional blanking. With the vee-ring, a counter plate and some other working parameters, a component with a precise geometry and smoothly blanked surface can be produced without any major secondary operations.However, these working parameters are always empirically determined or determined by trial-and-error method,which is time-consuming and expensive. In this study, a numerical simulation method was used to analyze the effect of vee-ring factors on product quality, such as distance between vee-ring and punch, vee-ring height and blank holder force, so as to obtain as high clean cut ratio as possible. During the simulation, the model was assumed as axisymmetric one and the workpiece was considered as rigid plastic material, meanwhile the tools were defined as rigid bodies so as to shorten the computational time. A damage model taking into account the influence of hydrostatic stress was used to simulate material fracture in fine-blanking. The result obtained from the simulation indicated that with the help of vee-ring, the metal material near the shear band does not flow with the punch penetration and high compressive stress in the shear band is generated. Consequently, higher clean cut ratio can be obtained with a vee-ring model than the one obtained with a plane blank holder model. Furthermore, the longer the distance between vee-ring and punch is, the higher the height of roll-over becomes.

  14. Flexural Toughness of Ring-Shaped Waste Bottle Fiber Concrete

    Directory of Open Access Journals (Sweden)

    Faisal S. K.

    2016-01-01

    Full Text Available Polyethylene terephthalate (PET bottles are plastic containers that are typically discarded, and thus, cause environmental pollution. To solve this problem, PET bottles are recycled incorporating with concrete. A ring-shaped PET (RPET fiber are introduced in this study and designed with a special shape to mobilize fiber yielding rather than fiber pullout. Therefore, aim of this paper is to investigate the influence of RPET bottles fibre in terms of toughness strength. The width of RPET fibers is fixed at 5 and 10 mm and the loads were applied to the third points of the specimen. The experiment indicates that RPET-5 and RPET-10 FC presented an increase in the toughness index of I20 on averages of 23.1% and 39.9% respectively, compared to normal specimens. It can conclude that incorporating RPET fiber in concrete presents significant improved of concrete properties.

  15. Beam Measurements in Storage Rings

    Science.gov (United States)

    Hofmann, Albert

    1996-05-01

    Beam measurements in storage rings are made to diagnose performance limitations and to gain knowledge of the beam behavior in view of improvements and to the benefit for other machines. In beam optics the measurement of the orbit or the trajectory with beam position monitors distributed around the ring reveals deflection errors. The overall focusing is checked by measuring the betatron frequency (tune) using a pulse or continuous excitation of the oscillation. Observing this oscillation with all the beam position monitors around the ring the beta function and the betatron phase advance are obtained. This measurement done for different momenta, i.e. RF-frequencies, gives the local chromaticity and its correction. The tune dependence on quadrupole strength gives the value of the local beta function. Synchrotron radiation is a powerful diagnostics tool and can give the beam cross section. Beam instabilities are investigated with similar methods. The growth or damping rates and frequencies of betatron and synchrotron oscillations, observed as a function of intensity, give a convolution of the resistive and reactive part of the transverse and longitudinal impedance with the spectrum of the oscillation mode. Coupled bunch instabilities are caused by narrow band impedances at particular frequencies while single traversal effects, including energy loss and bunch lengthening, are due to a broad band impedance. A model of the impedance can be constructed from such measurements done with different bunch lengths, tunes and other parameters. In some cases the element causing an instability can be identified. The dependence of the orbit and phase advance around the ring on intensity can give the location of impedances. To probe the impedance at very high frequencies the effects on very short bunches or the energy loss of a continuous beam due to its Schottky noise are measured. The beam energy, usually known from magnetic measurements, can be obtained directly with high

  16. China Plastics Industry (2011) China Plastics Processing Industry Association

    Institute of Scientific and Technical Information of China (English)

    Li Ying

    2012-01-01

    General situation of China plastics industry in 2011 was reviewed, including the output and export/import of plastics products, synthetic resins,and plastics processing machinery, as well as major economic data, such as the total industrial values, sales and profits of plastics products, etc. Analysis of the market of plastics products in 2011 was made, and the developing trend of China plastics industry in 2012 was proposed.

  17. K stability and stability of chiral ring

    CERN Document Server

    Collins, Tristan C; Yau, Shing-Tung

    2016-01-01

    We define a notion of stability for chiral ring of four dimensional N=1 theory by introducing test chiral rings and generalized a maximization. We conjecture that a chiral ring is the chiral ring of a superconformal field theory if and only if it is stable. We then study N=1 field theory derived from D3 branes probing a three-fold singularity X, and show that the K stability which implies the existence of Ricci-flat conic metric on X is equivalent to the stability of chiral ring of the corresponding field theory.

  18. Generalized fuzzy ideals of near-rings

    Institute of Scientific and Technical Information of China (English)

    ZHAN Jian-ming; Dawaz B.

    2009-01-01

    The concept of ((∈),(∈)V (q))-fuzzy subnear-rings (ideals) of a near-ring is introduced and some of its related properties are investigated. In particular, the relationships among ordinary fuzzy subnear-rings (ideals), (∈,∈V q)-fuzzy subnear-rings (ideals) and ((∈),(∈)V (q))-fuzzy subnearrings (ideals) of near-rings are described. Finally, some characterization of [μ]t is given by means of (∈,∈V q)-fuzzy ideals.

  19. Black Ring with a Positive Cosmological Constant

    CERN Document Server

    Chu, C S; Chu, Chong-Sun; Dai, Shou-Huang

    2007-01-01

    We construct a black ring with a cosmological constant in the five dimensional N=4 de Sitter supergravity theory. The black ring preserves half of the de Sitter supersymmetries. Unlike the flat case, this black ring is not rotating and the stability against gravitational self-attraction is balanced by the cosmological repulsion due to the cosmological constant. The black ring carries a dipole charge and this charge contributes to the first law of thermodynamics. The black ring has an entropy and mass which conform to the entropic N-bound proposal and the maximal mass conjecture.

  20. 5 CFR 890.1308 - Carrier participation.

    Science.gov (United States)

    2010-01-01

    ... 890.1308 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT (CONTINUED) CIVIL SERVICE REGULATIONS (CONTINUED) FEDERAL EMPLOYEES HEALTH BENEFITS PROGRAM Department of Defense Federal Employees Health Benefits Program Demonstration Project § 890.1308 Carrier participation. (a) All carriers who participate in the...

  1. Protection switching for carrier ethernet multicast

    DEFF Research Database (Denmark)

    Ruepp, Sarah Renée; Wessing, Henrik; Berger, Michael Stübert

    2010-01-01

    This paper addresses network survivability for IPTV multicast transport in Carrier Ethernet networks. The impact of link failures is investigated and suggestions for intelligent multicast resilience schemes are proposed. In particular, functions of the multicast tree are integrated with the Carrier...

  2. The Prism Plastic Calorimeter (PPC)

    CERN Multimedia

    2002-01-01

    This proposal supports two goals: \\\\ \\\\ First goal:~~Demonstrate that current, widely used plastic technologies allow to design Prism Plastic Calorimeter~(PPC) towers with a new ``liquid crystal'' type plastic called Vectra. It will be shown that this technique meets the requirements for a LHC calorimeter with warm liquids: safety, hermeticity, hadronic compensation, resolution and time response. \\\\ \\\\ Second goal:~~Describe how one can design a warm liquid calorimeter integrated into a LHC detector and to list the advantages of the PPC: low price, minimum of mechanical structures, minimum of dead space, easiness of mechanical assembly, accessibility to the electronics, possibility to recirculate the liquid. The absorber and the electronic being outside of the liquid and easily accessible, one has maximum flexibility to define them. \\\\ \\\\ The R&D program, we define here aims at showing the feasibility of these new ideas by building nine towers of twenty gaps and exposing them to electron and hadron beams.

  3. Plasticity in glutamatergic NTS neurotransmission.

    Science.gov (United States)

    Kline, David D

    2008-12-10

    Changes in the physiological state of an animal or human can result in alterations in the cardiovascular and respiratory system in order to maintain homeostasis. Accordingly, the cardiovascular and respiratory systems are not static but readily adapt under a variety of circumstances. The same can be said for the brainstem circuits that control these systems. The nucleus tractus solitarius (NTS) is the central integration site of baroreceptor and chemoreceptor sensory afferent fibers. This central nucleus, and in particular the synapse between the sensory afferent and second-order NTS cell, possesses a remarkable degree of plasticity in response to a variety of stimuli, both acute and chronic. This brief review is intended to describe the plasticity observed in the NTS as well as the locus and mechanisms as they are currently understood. The functional consequence of NTS plasticity is also discussed.

  4. TECHNICAL CHARACTERIZATION OF ECO-COMPATIBLE PLASTIC FILMS FOR SOIL SOLARIZATION: FOUR YEARS OF EXPERIMENTS

    Directory of Open Access Journals (Sweden)

    Salvatore Margiotta

    2007-12-01

    Full Text Available Soil solarization relies on solar radiation being converted to heat for the killing of soilborne pathogens. On one hand, this technique can be considered as an environmentally-friendly way to manage soilborne pests, as an alternative of methyl bromide phased-out in 2005, than using chemicals. On the other hand, high employment of traditional plastic sheets in agriculture causes the production of enormous quantities of waste, whose inappropriate management might have negative effects on the environment. In order to determine a reduction of the charge of plastic waste and to facilitate the waste disposal, one of the most interesting approaches, from an environmental point of view, lies in the location of innovatory plastic films such as co-extruded ultrathin films, which are able to reduce the plastic quantity to be managed, and biodegradable laminates, which after a first usage, will spontaneously start up a degradation process that avoids their collection and their consequent disposal. Beside the ecological proprieties of these innovative films, it is necessary to study their technical and agronomical behavior in order to determine their efficiency and the possibility to be used in place of the traditional plastic films. This paper represents a review of the researches carrier out by the Technical Economics Department of the University of Basilicata (Italy in the last years (1999, 2000, 2002 and 2003 on the technical performances of some innovative plastic films used for soil solarization.

  5. Stable carbon isotopes in tree rings: the failure of uniformitarianism

    Science.gov (United States)

    McCarroll, Danny

    2010-05-01

    When tree rings are used to reconstruct past climate we rely on the uniformitarian principle that ‘the present is the key to the past'. Relationships between measured parameters and climate that can be calibrated and verified over the instrumental period are assumed to be applicable at longer timescales. In the case of δ13C, however, the uniformitarian principle fails for two reasons. (1) The instrumental calibration period is also the period of anthropogenic increase in atmospheric CO2. δ13C is a function of the ratio of internal to ambient CO2, so maintaining constant δ13C over the industrial period requires an active plastic response, either restricting stomatal conductance or increasing assimilation rate. In some areas trees may have reached the limits of their plasticity so that over the last few decades δ13C values have been declining, independent of any changes in climate. If no correction is made, the recent response to climate will be a poor indicator of behaviour in the past. (2) Tree ring δ13C is often used to reconstruct past temperatures even though temperature rarely has a strong direct control over fractionation. The link is therefore via either sunshine or humidity, which over the calibration period may be very strongly correlated with temperature. Long isotope chronologies, when compared with independent evidence of past temperatures, however, can show periods of marked divergence. The strong covariance of temperature, sunshine and humidity over the last century may not have persisted over longer timescales with larger climatic perturbations. In the case of carbon isotopes the key to the past is not statistical inference based on recent behaviour, but a clear mechanistic understanding of the influence of climate and other factors on fractionation.

  6. DYNAMICAL BALANCE STUDY OF RING REDUCER

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    The basic structure of epicyclical gear transmission with inner teeth of single-ring, double-ring, three-ring and four-ring reducer are analyzed. The force analysis model of ring reducer is built. Following this, it is concluded that the present ring reducers have the problem that the inertia force or the inertia moment is lopsided. On the base of analysis and calculation the balanced ring reducer which can realize the balance of inertia force and inertia moment is brought forward, and so is its concrete realizing step. The specimen of the balanced ring reducer is designed and manufactured; the experiment is carried out on the gear transmission test bench. Compared with other ring reducer of the same power, the balanced ring reducer has many advantages, such as low vibration noise, low cost and less production difficulty and less heat. It is the substitute of other ring reducer of the same kind. Therefore, it has important theoretic significance and highly practical engineering value.

  7. Selection of Carrier Waveforms for PWM Inverter

    Institute of Scientific and Technical Information of China (English)

    陈国呈; 屈克庆; 许春雨; 孙承波

    2003-01-01

    In this paper the influence of different carrier waveforms upon the output characteristics of PWM inverter is described in detail. When a triangular carrier waveform is used in hard-switching PWM inverters, harmonics exist in the neighborhood of the output frequency of the inverter output voltage and current due to the dead time. The triangular carrier waveform used in soft-switching PWM inverter will cause difficulties in controlling resonance-trigger time, higher loss in the resonant circuit, and less utilization of the DC bus voltage. If a sawtooth carrier is used in hard-switching PWM inverter, there will be severe distortion in the current waveform. When sawtooth carriers with alternate positive and negative slopes are used in soft-switching PWM inverters, the resonancetrigger time is easy to control, and distortion in the output voltage and current caused by the dead time will not appear.

  8. The Kinetics of Carrier Transport Inhibition

    DEFF Research Database (Denmark)

    Rosenberg, T.; Wilbrandt, Robert Walter

    1962-01-01

    The kinetical treatment of enzymatic carrier transports as given in previous communications has been extended to conditions of inhibition. Various possible types of inhibitors have been considered differing in the site of attack (enzyme or carrier), in the mode of action (competing...... with the substrate for the enzyme or the carrier or for both, competing with the carrier for the enzyme, or non-competitive) and in the ability of penetrating the membrane. Experiments are reported on the inhibition of glucose and fructose transport across the human red cell membrane by phlorizine, phloretine...... the first order asymmetry severalfold (“second order asymmetry”). It was shown that a substrate competitive mode of action involving competition both for the enzyme and for the enzyme-bound carrier will result in a behaviour resembling the observed “second order asymmetry”. It is felt, therefore...

  9. Modeling of Carrier Dynamics in Electroabsorption Modulators

    DEFF Research Database (Denmark)

    Højfeldt, Sune

    2002-01-01

    and a phenomenological model for the carrier sweep-out dynamics, we investigate all-optical wavelength conversion, all-optical signal regeneration, and all-optical demultiplexing. A detailed drift-diffusion type model for the sweerp-out of photo-excited carriers in electroabsorption modulators is presented. We use...... the model to calclulate absorption spectra and steady-state carrier distributions in different modulator structures. This allows us to investigate a number of important properties of electroabsorption modulators, such as the electroabsorption effect and th saturation properties. We also investigate...... the influence that carrier recapture has on the device properties, and we discuss the recapture process on a more fundamental level. The model is also used to investigate in detail the carrier sweep-out process in electroabsorption modulators. We investigate how the intrinsic-region width, the separate...

  10. Feasibility of a ring FEL at low emittance storage rings

    Energy Technology Data Exchange (ETDEWEB)

    Agapov, I., E-mail: ilya.agapov@xfel.eu

    2015-09-01

    A scheme for generating coherent radiation at latest generation low emittance storage rings such as PETRA III at DESY (Balewski et al., 2004 [1]) is proposed. The scheme is based on focusing and subsequent defocusing of the electron beam in the longitudinal phase space at the undulator location. The expected performance characteristics are estimated for radiation in the wavelength range of 500–1500 eV. It is shown that the average brightness is increased by several orders of magnitude compared to spontaneous undulator radiation, which can open new perspectives for photon-hungry soft X-ray spectroscopy techniques.

  11. SEM, XRD and electrical conductivity studies of PVDF-HFP-LiBF4 -EC plasticized gel polymer electrolyte

    Science.gov (United States)

    Sangeetha, M.; Mallikarjun, A.; Jaipal Reddy, M.; Siva Kumar, J.

    2017-07-01

    Micro porous gel type polymer electrolytes composed of 80 Wt% PVDF-HFP polymer - 20 Wt% LiBF4 salt in different concentrations of EC plasticizer (10Wt% - 70 Wt %) plasticizer have been synthesized by Solution cast technique. The effect of plasticizer in polymer-salt matrix, structural, morphological and ionic conductivity is studied. Structural and morphological studies showed increase in amorphous nature and recrystallization after a certain limit of EC plasticizer. The highest ionic conductivity of 1.510 × 10-3 Cm-1 is found for 40 Wt% of EC plasticizer at 303K. Addition of plasticizer increase free volume enables segmental motion of polymer and free mobility of ions. Also it provides more number of charge carriers in turn enhances the ionic conductivity up to certain limit of 40 Wt% of EC plasticizer. Further increase of plasticizer content creates ion-pair aggregation and recrystallization which reduces the ionic conductivity. The ionic conductivity obeys the VTF relationship for Gel type polymer electrolyte system.

  12. Polishing compound for plastic surfaces

    Science.gov (United States)

    Stowell, Michael S.

    1995-01-01

    A polishing compound for plastic surfaces. The compound contains by weight approximately 4 to 17 parts at least one petroleum distillate lubricant, 1 to 6 parts mineral spirits, 2.5 to 15 parts abrasive particles, and 2.5 to 10 parts water. The abrasive is tripoli or a similar material that contains fine particles silica. Preferably, most of the abrasive particles are less than approximately 10 microns, more preferably less than approximately 5 microns in size. The compound is used on PLEXIGLAS.TM., LEXAN.TM., LUCITE.TM., polyvinyl chloride (PVC) and similar plastic materials whenever a smooth, clear polished surface is desired.

  13. Polishing compound for plastic surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Stowell, M.S.

    1993-01-01

    A polishing compound for plastic surfaces is disclosed. The compound contains by weight approximately 4 to 17 parts at least one petroleum distillate lubricant, 1 to 6 parts mineral spirits, 2.5 to 15 parts abrasive particles, and 2.5 to 10 parts water. The abrasive is tripoli or a similar material that contains colloidal silica. Preferably, most of the abrasive particles are less than approximately 10 microns, more preferably less than approximately 5 microns in size. The compound is used on PLEXIGLAS{sup TM}, LEXAN{sup TM}, LUCITE{sup TM}, polyvinyl chloride (PVC) and similar plastic materials whenever a smooth, clear polished surface is desired.

  14. Hydrogen: the future energy carrier.

    Science.gov (United States)

    Züttel, Andreas; Remhof, Arndt; Borgschulte, Andreas; Friedrichs, Oliver

    2010-07-28

    Since the beginning of the twenty-first century the limitations of the fossil age with regard to the continuing growth of energy demand, the peaking mining rate of oil, the growing impact of CO2 emissions on the environment and the dependency of the economy in the industrialized world on the availability of fossil fuels became very obvious. A major change in the energy economy from fossil energy carriers to renewable energy fluxes is necessary. The main challenge is to efficiently convert renewable energy into electricity and the storage of electricity or the production of a synthetic fuel. Hydrogen is produced from water by electricity through an electrolyser. The storage of hydrogen in its molecular or atomic form is a materials challenge. Some hydrides are known to exhibit a hydrogen density comparable to oil; however, these hydrides require a sophisticated storage system. The system energy density is significantly smaller than the energy density of fossil fuels. An interesting alternative to the direct storage of hydrogen are synthetic hydrocarbons produced from hydrogen and CO2 extracted from the atmosphere. They are CO2 neutral and stored like fossil fuels. Conventional combustion engines and turbines can be used in order to convert the stored energy into work and heat.

  15. Methanol as an energy carrier

    Energy Technology Data Exchange (ETDEWEB)

    Biedermann, P.; Grube, T.; Hoehlein, B. (eds.)

    2006-07-01

    For the future, a strongly growing energy demand is expected in the transport sector worldwide. Economically efficient oil production will run through a maximum in the next decade. Higher fuel prices and an environmentally desirable reduction of emissions will increase the pressure for reducing fuel consumption and emissions in road traffic. These criteria show the urgent necessity of structural changes in the fuel market. Due to its advantages concerning industrial-scale production, storage and global availability, methanol has the short- to medium-term potential for gaining increased significance as a substitution product in the energy market. Methanol can be produced both from fossil energy sources and from biomass or waste materials through the process steps of synthesis gas generation with subsequent methanol synthesis. Methanol has the potential to be used in an environmentally friendly manner in gasoline/methanol mixtures for flexible fuel vehicles with internal combustion engines and in diesel engines with pure methanol. Furthermore, it can be used in fuel cell vehicles with on-board hydrogen production in direct methanol fuel cell drives, and in stationary systems for electricity and heat generation as well as for hydrogen production. Finally, in portable applications it serves as an energy carrier for electric power generation. In this book, the processes for the production and use of methanol are presented and evaluated, markets and future options are discussed and issues of safety and environmental impacts are addressed by a team of well-known authors. (orig.)

  16. Improvement through low cost biofilm carrier in anaerobic tubular digestion in cold climate regions.

    Science.gov (United States)

    Martí-Herrero, J; Alvarez, R; Rojas, M R; Aliaga, L; Céspedes, R; Carbonell, J

    2014-09-01

    The aim of this research is to evaluate the increase of biogas production with low cost tubular digesters in cold climates using PET rings inside the reactor. Two similar digesters have been operated and monitored in cold weather conditions and have been fed with cow manure. Digester 1 was filled with PET - rings as a biofilm carrier, Digester 2 was kept as a reference. Through the PET - rings the functional surface could be increased by a factor 4.2. The results show that 44% more biogas per Kg SV has been produced with the biofilm carrier in use (0.33 m(3)/kg SV) (reference digester -0.23 m(3)/kg SV), at an organic load rate of 0.26 kg SV/m(3)/d. The thermal performance shows that with an adaptation of the low cost tubular digester the slurry temperature can be raised up to 16.6°C (average) by surrounding temperature of 6.1°C (average) without using any active heating system.

  17. Carrier-carrier relaxation kinetics in quantum well semiconductor structures with nonparabolic energy bands

    DEFF Research Database (Denmark)

    Dery, H.; Tromborg, Bjarne; Eisenstein, G.

    2003-01-01

    We describe carrier-carrier scattering dynamics in an inverted quantum well structure including the nonparabolic nature of the valance band. A solution of the semiconductor Bloch equations yields strong evidence to a large change in the temporal evolution of the carrier distributions compared...... to the case of parabolic bands. The nonparabolic bands and the consequent change in the density of states reduce considerably the degree of gain saturation while decreasing the time constant governing the relaxation. This results in a measurable reduction of the role played by carrier-carrier scattering...

  18. Einstein Ring in Distant Universe

    Science.gov (United States)

    2005-06-01

    Using ESO's Very Large Telescope, Rémi Cabanac and his European colleagues have discovered an amazing cosmic mirage, known to scientists as an Einstein Ring. This cosmic mirage, dubbed FOR J0332-3557, is seen towards the southern constellation Fornax (the Furnace), and is remarkable on at least two counts. First, it is a bright, almost complete Einstein ring. Second, it is the farthest ever found. ESO PR Photo 20a/05 ESO PR Photo 20a/05 Deep Image of a Region in Fornax (FORS/VLT) [Preview - JPEG: 400 x 434 pix - 60k] [Normal - JPEG: 800 x 867 pix - 276k] [Full Res - JPEG: 1859 x 2015 pix - 3.8M] ESO PR Photo 20b/05 ESO PR Photo 20b/05 Zoom-in on the Newly Found Einstein Ring (FORS/VLT) [Preview - JPEG: 400 x 575 pix - 168k] [Normal - JPEG: 630 x 906 pix - 880k] Caption: ESO PR Photo 20a/05 is a composite image taken in two bands (B and R) with VLT/FORS1 of a small portion of the sky (field-of-view 7x7' or 1/15th of the area of the full moon). The faintest object seen in the image has a magnitude 26, that is, it is 100 million times fainter than what can be observed with the unaided eye. The bright elliptical galaxy on the lower-left quadrant is a dwarf galaxy part of a large nearby cluster in the Fornax constellation. As for all deep images of the sky, this field shows a variety of objects, the brightest ponctual sources being stars from our Galaxy. By far the field is dominated by thousands of faint background galaxies the colours of which are related to the age of their dominant stellar population, their dust content and their distance. The newly found Einstein ring is visible in the top right part of the image. ESO PR Photo 20b/05 zooms-in on the position of the newly found cosmic mirage. ESO PR Photo 20c/05 ESO PR Photo 20c/05 Einstein Ring in Distant Universe (FORS/VLT) [Preview - JPEG: 400 x 584 pix - 104k] [Normal - JPEG: 800 x 1168 pix - 292k] [Full Res - JPEG: 1502 x 2192 pix - 684k] Caption of ESO PR Photo 20c/05: The left image is magnified and centred

  19. 77 FR 46555 - Motor Carrier Safety Advisory Committee: Public Meeting

    Science.gov (United States)

    2012-08-03

    ... Federal Motor Carrier Safety Administration Motor Carrier Safety Advisory Committee: Public Meeting AGENCY: Federal Motor Carrier Safety Administration (FMCSA), DOT. ACTION: Notice of meeting of Motor Carrier... major motor carrier safety provisions of the recently enacted Moving Ahead for Progress in the...

  20. Differential Analysis of the Nasal Microbiome of Pig Carriers or Non-Carriers of Staphylococcus aureus

    DEFF Research Database (Denmark)

    Espinosa-Gongora, Carmen; Larsen, Niels; Schonning, Kristian;

    2016-01-01

    Staphylococcus aureus is presently regarded as an emerging zoonotic agent due to the spread of specific methicillin-resistant S. aureus (MRSA) clones in pig farms. Studying the microbiota can be useful for the identification of bacteria that antagonize such opportunistic veterinary and zoonotic...... pathogen in animal carriers. The aim of this study was to determine whether the nasal microbiome of pig S. aureus carriers differs from that of non-carriers. The V3-V5 region of the 16S rRNA gene was sequenced from nasal swabs of 44 S. aureus carriers and 56 non-carriers using the 454 GS FLX titanium...... system. Carriers and non-carriers were selected on the basis of quantitative longitudinal data on S. aureus carriage in 600 pigs sampled at 20 Danish herds included in two previous studies in Denmark. Raw sequences were analysed with the BION meta package and the resulting abundance matrix was analysed...