WorldWideScience

Sample records for plastic pieces typically

  1. Pieces

    DEFF Research Database (Denmark)

    Jensen, Niels Henrik

    1990-01-01

    The report presents results from the SIP project (System Representation in Process Control). PIECES is a graphical, interactive user interface system designed and programmed as a tool for building, manipulating and using a Multilevel Flow Model (MFM - Morten Lind, Tecnical University of Denmark)....

  2. UTILIZATION OF STEREOLOGY FOR QUANTITATIVE ANALYSIS OF PLASTIC DEFORMATION OF FORMING PIECES

    Directory of Open Access Journals (Sweden)

    Maroš Martinkovič

    2012-01-01

    Full Text Available Mechanical working leads to final properties of forming pieces, which are affected by conditions of production technology. Utilization of stereology leads to the detail analysis of three-dimensional plastic deformed material structure by different forming technologies, e.g. forging, extruding, upsetting, metal spinning, drawing etc. The microstructure of cold drawing wires was analyzed. Grain boundaries orientation was measured on the parallel section of wire with a different degree of deformation and direct axis plastic deformation was evaluated in bulk formed part. The strain of probes on their sections was obtained using stereology by measurement of degree of grain boundary orientation which was converted to deformation using model of conversion of grain boundary orientation degree to deformation.

  3. Processing and characterization of 3D dense chitosan pieces, for orthopedic applications, by adding plasticizers

    OpenAIRE

    Figueiredo, Lígia; Moura, Carla; Pinto, Luís F. V.; Ferreira, Frederico Castelo; Rodrigues, Alexandra

    2015-01-01

    In this work, plasticizer agents were incorporated in a chitosan based formulation, as a strategy to improve the fragile structure of chitosan based-materials. Three different plasticizers: ethylene glycol, glycerol and sorbitol, were blended with chitosan to prepare 3D dense chitosan specimens. The properties of the obtained structures were assessed for mechanical, microstructural, physical and biocompatibility behavior. The results obtained revealed that from the different specimens prepare...

  4. Experimental study of fiber-glass plastic work pieces contour milling

    Science.gov (United States)

    Trushin, N. N.; Lisitsin, V. N.

    2018-03-01

    The article represents the results of study of cut and feed speed influence on wear of monolithic hard alloy end milling cutter during cutting of foiled fiber-glass plastic sheets, used for printed-circuit boards’ production. The peculiarities and problems of cutting layered materials are described. The most effective feed and cut speed values are determined by cutter wear analysis.

  5. Analysis of the influencing factors of PAEs volatilization from typical plastic products.

    Science.gov (United States)

    Chen, Weidong; Chi, Chenchen; Zhou, Chen; Xia, Meng; Ronda, Cees; Shen, Xueyou

    2018-04-01

    The primary emphasis of this research was to investigate the foundations of phthalate (PAEs) pollutant source researches and then firstly confirmed the concept of the coefficient of volatile strength, namely phthalate total content in per unit mass and unit surface area of pollutant sources. Through surveying and evaluating the coefficient of volatile strength of PAEs from typical plastic products, this research carried out reasonable classification of PAEs pollutant sources into three categories and then investigated the relationship amongst the coefficient of volatile strength as well as other environmental factors and the concentration level of total PAEs in indoor air measured in environment chambers. Research obtained phthalate concentration results under different temperature, humidity, the coefficient of volatile strength and the closed time through the chamber experiment. In addition, this study further explored the correlation and ratio of influencing factors that affect the concentration level of total PAEs in environment chambers, including environmental factors, the coefficient of volatile strengths of PAEs and contents of total PAEs in plastic products. The research created an improved database system of phthalate the coefficient of volatile strengths of each type of plastic goods, and tentatively revealed that the volatile patterns of PAEs from different typical plastic goods, finally confirmed that the coefficient of volatile strengths of PAEs is a major factor that affects the indoor air total PAEs concentration, which laid a solid foundation for further establishing the volatile equation of PAEs from plastic products. Copyright © 2017. Published by Elsevier B.V.

  6. Investigation on the toxic interaction of typical plasticizers with calf thymus DNA

    Energy Technology Data Exchange (ETDEWEB)

    Sun, Xiaojing [School of Environmental Science and Engineering, China–America CRC for Environment & Health, Shandong University, 27# Shanda South Road, Jinan 250100, Shandong Province (China); Zong, Wansong, E-mail: gaocz@sdu.edu.cn [College of Population, Resources and Environment, Shandong Normal University, 88# East Wenhua Road, Jinan 250014 (China); Liu, Chunguang; Liu, Yang [School of Environmental Science and Engineering, China–America CRC for Environment & Health, Shandong University, 27# Shanda South Road, Jinan 250100, Shandong Province (China); Gao, Canzhu, E-mail: rutaoliu@sdu.edu.cn [School of Environmental Science and Engineering, China–America CRC for Environment & Health, Shandong University, 27# Shanda South Road, Jinan 250100, Shandong Province (China); Liu, Rutao [School of Environmental Science and Engineering, China–America CRC for Environment & Health, Shandong University, 27# Shanda South Road, Jinan 250100, Shandong Province (China)

    2015-05-15

    The interactions of typical plasticizers dimethyl phthalate (DMP), diethyl phthalate (DEP) and dibutyl phthalate (DBP) with calf thymus DNA (ctDNA) were investigated by fluorescence spectroscopic techniques and molecular modeling. Experimental results indicated that the characteristic fluorescence intensity of phthalic acid rose with the increase of DNA concentration; while the characteristic fluorescence intensities of plasticizers decreased with the increase of DNA concentration. Experiments on native and denatured DNA determined that plasticizers interacted with DNA both in groove and electrostatic binding mode. The molecular modeling results further illustrated that there is groove binding between them; hydrogen bonding and Van der Waals interactions were the main forces. With the extension of branched-chains, the binding effects between plasticizers and DNA were weakened, which could be related to the increased steric hindrance. - Highlights: • This work established the binding mode of plasticizers with DNA on molecular level. • The mechanism was explored by fluorescence spectroscopic and molecular docking methods. • There are two kinds of binding mode between DMP, DEP, DBP and DNA, electrostatic and groove. • With the branched chain extension, the binding effect of plasticizers and DNA has been weakened.

  7. Plastic Pollution in the World's Oceans: More than 5 Trillion Plastic Pieces Weighing over 250,000 Tons Afloat at Sea.

    Directory of Open Access Journals (Sweden)

    Marcus Eriksen

    Full Text Available Plastic pollution is ubiquitous throughout the marine environment, yet estimates of the global abundance and weight of floating plastics have lacked data, particularly from the Southern Hemisphere and remote regions. Here we report an estimate of the total number of plastic particles and their weight floating in the world's oceans from 24 expeditions (2007-2013 across all five sub-tropical gyres, costal Australia, Bay of Bengal and the Mediterranean Sea conducting surface net tows (N = 680 and visual survey transects of large plastic debris (N = 891. Using an oceanographic model of floating debris dispersal calibrated by our data, and correcting for wind-driven vertical mixing, we estimate a minimum of 5.25 trillion particles weighing 268,940 tons. When comparing between four size classes, two microplastic 4.75 mm, a tremendous loss of microplastics is observed from the sea surface compared to expected rates of fragmentation, suggesting there are mechanisms at play that remove <4.75 mm plastic particles from the ocean surface.

  8. Plastic Pollution in the World's Oceans: More than 5 Trillion Plastic Pieces Weighing over 250,000 Tons Afloat at Sea

    Science.gov (United States)

    Eriksen, Marcus; Lebreton, Laurent C. M.; Carson, Henry S.; Thiel, Martin; Moore, Charles J.; Borerro, Jose C.; Galgani, Francois; Ryan, Peter G.; Reisser, Julia

    2014-01-01

    Plastic pollution is ubiquitous throughout the marine environment, yet estimates of the global abundance and weight of floating plastics have lacked data, particularly from the Southern Hemisphere and remote regions. Here we report an estimate of the total number of plastic particles and their weight floating in the world's oceans from 24 expeditions (2007–2013) across all five sub-tropical gyres, costal Australia, Bay of Bengal and the Mediterranean Sea conducting surface net tows (N = 680) and visual survey transects of large plastic debris (N = 891). Using an oceanographic model of floating debris dispersal calibrated by our data, and correcting for wind-driven vertical mixing, we estimate a minimum of 5.25 trillion particles weighing 268,940 tons. When comparing between four size classes, two microplastic 4.75 mm, a tremendous loss of microplastics is observed from the sea surface compared to expected rates of fragmentation, suggesting there are mechanisms at play that remove plastic particles from the ocean surface. PMID:25494041

  9. Plastic Pollution in the World's Oceans: More than 5 Trillion Plastic Pieces Weighing over 250,000 Tons Afloat at Sea.

    Science.gov (United States)

    Eriksen, Marcus; Lebreton, Laurent C M; Carson, Henry S; Thiel, Martin; Moore, Charles J; Borerro, Jose C; Galgani, Francois; Ryan, Peter G; Reisser, Julia

    2014-01-01

    Plastic pollution is ubiquitous throughout the marine environment, yet estimates of the global abundance and weight of floating plastics have lacked data, particularly from the Southern Hemisphere and remote regions. Here we report an estimate of the total number of plastic particles and their weight floating in the world's oceans from 24 expeditions (2007-2013) across all five sub-tropical gyres, costal Australia, Bay of Bengal and the Mediterranean Sea conducting surface net tows (N = 680) and visual survey transects of large plastic debris (N = 891). Using an oceanographic model of floating debris dispersal calibrated by our data, and correcting for wind-driven vertical mixing, we estimate a minimum of 5.25 trillion particles weighing 268,940 tons. When comparing between four size classes, two microplastic 4.75 mm, a tremendous loss of microplastics is observed from the sea surface compared to expected rates of fragmentation, suggesting there are mechanisms at play that remove plastic particles from the ocean surface.

  10. Contamination and risk of heavy metals in soils and sediments from a typical plastic waste recycling area in North China.

    Science.gov (United States)

    Tang, Zhenwu; Zhang, Lianzhen; Huang, Qifei; Yang, Yufei; Nie, Zhiqiang; Cheng, Jiali; Yang, Jun; Wang, Yuwen; Chai, Miao

    2015-12-01

    Plastic wastes are increasingly being recycled in many countries. However, available information on the metals released into the environment during recycling processes is rare. In this study, the contamination features and risks of eight heavy metals in soils and sediments were investigated in Wen'an, a typical plastic recycling area in North China. The surface soils and sediments have suffered from moderate to high metal pollution and in particular, high Cd and Hg pollution. The mean concentrations of Cd and Hg were 0.355 and 0.408 mg kg(-1), respectively, in the soils and 1.53 and 2.10 mg kg(-1), respectively, in the sediments. The findings suggested that there is considerable to high potential ecological risks in more than half of the soils and high potential ecological risk in almost all sediments. Although the health risk levels from exposure to soil metals were acceptable for adults, the non-carcinogenic risks to local children exceeded the acceptable level. Source assessment indicated that heavy metals in soils and sediments were mainly derived from inputs from poorly controlled plastic waste recycling operations in this area. The results suggested that the risks associated with heavy metal pollution from plastic waste recycling should be of great concern. Copyright © 2015 Elsevier Inc. All rights reserved.

  11. Plastic

    International Nuclear Information System (INIS)

    Jeong Gi Hyeon

    1987-04-01

    This book deals with plastic, which includes introduction for plastic, chemistry of high polymers, polymerization, speciality and structure of a high molecule property of plastic, molding, thermosetting plastic, such as polyethylene, polyether, polyamide and polyvinyl acetyl, thermal plastic like phenolic resins, xylene resins, melamine resin, epoxy resin, alkyd resin and poly urethan resin, new plastic like ionomer and PPS resin, synthetic laminated tape and synthetic wood, mixed materials in plastic, reprocessing of waste plastic, polymer blend, test method for plastic materials and auxiliary materials of plastic.

  12. Research on the recycling industry development model for typical exterior plastic components of end-of-life passenger vehicle based on the SWOT method.

    Science.gov (United States)

    Zhang, Hongshen; Chen, Ming

    2013-11-01

    In-depth studies on the recycling of typical automotive exterior plastic parts are significant and beneficial for environmental protection, energy conservation, and sustainable development of China. In the current study, several methods were used to analyze the recycling industry model for typical exterior parts of passenger vehicles in China. The strengths, weaknesses, opportunities, and challenges of the current recycling industry for typical exterior parts of passenger vehicles were analyzed comprehensively based on the SWOT method. The internal factor evaluation matrix and external factor evaluation matrix were used to evaluate the internal and external factors of the recycling industry. The recycling industry was found to respond well to all the factors and it was found to face good developing opportunities. Then, the cross-link strategies analysis for the typical exterior parts of the passenger car industry of China was conducted based on the SWOT analysis strategies and established SWOT matrix. Finally, based on the aforementioned research, the recycling industry model led by automobile manufacturers was promoted. Copyright © 2013 Elsevier Ltd. All rights reserved.

  13. Transition piece for joining together tubular pieces

    International Nuclear Information System (INIS)

    Holko, K.H.

    1981-01-01

    A transition piece for joining together tubular pieces formed respectively from a low alloy or carbon steel and a high temperature alloy containing at least 16% chromium includes a plurality of tubular parts welded together and formed from materials of selected composition with a maximum chromium content difference of 5% between adjacent parts when the chromium content of each part is below 10% and a maximum chromium difference of 7% between adjacent parts when the chromium content of either part is above 10%. The transition parts are also graded as to such characteristics as thermal expansion coefficient. The transition parts at opposite ends of the transition joint have chromium percentages similar to the tubular pieces to which they are to be joined. The parts may be joined by fusion and/or friction welding and parts may be formed by fusion weld deposition. (author)

  14. Mine cross piece

    Energy Technology Data Exchange (ETDEWEB)

    Belik, I P; Gorbatenko, A Ye

    1982-01-01

    The mine cross piece includes main and supplementary parachute-formed cupolas made of air-impermeable fabric, resources for attachment made in the form of shroud lines. In order to improve its reliability with prolonged localization of an underground fire, the cavity between the cupolas connects to the source of fast-hardening material. In this case the cupolas are arranged co-directionally in relation to each other, while the shroud lines of the main are attached to the cupola of the supplemental which is made with perforations.

  15. Piece of the sun

    CERN Document Server

    Wayne, Teddy

    2015-01-01

    Our rapidly industrialising world has an insatiable hunger for energy, and conventional sources are struggling to meet demand. Oil is running out, coal is damaging our climate, many nations are abandoning nuclear, yet solar, wind and water will never be a complete replacement. The solution, says Daniel Clery in this deeply researched and revelatory book, is to be found in the original energy source: the Sun itself. There, at its centre, the fusion of 630 million tonnes of hydrogen every second generates an unfathomable amount of energy. By replicating even a tiny piece of the Sun's power

  16. One piece reactor removal

    International Nuclear Information System (INIS)

    Chia, Wei-Min; Wang, Song-Feng

    1993-01-01

    The strategy of Taiwan Research Reactor Renewal plan is to remove the old reactor block with One Piece Reactor Removal (OPRR) method for installing a new research reactor in original building. In this paper, the engineering design of each transportation works including the work method, the major equipments, the design policy and design criteria is described and discussed. In addition, to ensure the reactor block is safety transported for storage and to guarantee the integrity of reactor base mat is maintained for new reactor, operation safety is drawn special attention, particularly under seismic condition, to warrant safe operation of OPRR. ALARA principle and Below Regulatory Concern (BRC) practice were also incorporated in the planning to minimize the collective dose and the total amount of radioactive wastes. All these activities are introduced in this paper. (J.P.N.)

  17. Ingested plastic in a diving seabird, the thick-billed murre (Uria lomvia), in the eastern Canadian Arctic.

    Science.gov (United States)

    Provencher, Jennifer F; Gaston, Anthony J; Mallory, Mark L; O'hara, Patrick D; Gilchrist, H Grant

    2010-09-01

    Plastic debris has become ubiquitous in the marine environment and seabirds may ingest debris which can have deleterious effects on their health. In the North Atlantic Ocean, surface feeding seabirds typically ingest high levels of plastic, while the diving auks which feed in the water column typically have much lower levels. We examined 186 thick-billed murres from five colonies in the eastern Canadian Arctic for ingested plastic debris. Approximately 11% of the birds had at least one piece of plastic debris in their gastrointestinal tracts, with debris dominated by user plastics. This is the first report of ingested plastics in an auk species in Canada's Arctic, and the highest incidence of plastic ingestion to date for thick-billed murres (Uria lomvia). Copyright 2010 Elsevier Ltd. All rights reserved.

  18. Musings on the puzzle piece.

    Science.gov (United States)

    Goin-Kochel, Robin P

    2016-02-01

    Following is a brief musing on Roy Grinker's discussion of what the puzzle piece symbolizes for autism during his presentation at the 2015 International Meeting for Autism Research. In his words, "The puzzle piece is ubiquitous." It likely holds a different meaning for each of us, and this is how one autism researcher sees it. © The Author(s) 2015.

  19. Hydride precipitation, fracture and plasticity mechanisms in pure zirconium and Zircaloy-4 at temperatures typical for the postulated loss-of-coolant accident

    International Nuclear Information System (INIS)

    Pshenichnikov, Anton; Stuckert, Juri; Walter, Mario

    2016-01-01

    Highlights: • All δ-hydrides in Zr and Zircaloy-4 have basal or pyramidal types of habit planes. • Seven orientation relationships for δ-hydrides in Zr matrix were detected. • Decohesion fracture mechanism of hydrogenated Zr was investigated by fractography. - Abstract: The results of investigations of samples of zirconium and its alloy Zircaloy-4, hydrogenated at temperatures 900–1200 K (typical temperatures for loss-of-coolant accidents) are presented. The analyses, based on a range of complementary techniques (X-ray diffraction, scanning electron microscopy, electron backscatter diffraction) reveals the direct interrelation of internal structure transformation and hydride distribution with the degradation of mechanical properties. Formation of small-scale zirconium hydrides and their bulk distribution in zirconium and Zircaloy-4 were investigated. Fractographical analysis was performed on the ruptured samples tested in a tensile machine at room temperature. The already-known hydrogen embrittlement mechanisms based on hydride formation and hydrogen-enhanced decohesion and the applicability of them in the case of zirconium and its alloys is discussed.

  20. Typical entanglement

    Science.gov (United States)

    Deelan Cunden, Fabio; Facchi, Paolo; Florio, Giuseppe; Pascazio, Saverio

    2013-05-01

    Let a pure state | ψ> be chosen randomly in an NM-dimensional Hilbert space, and consider the reduced density matrix ρ A of an N-dimensional subsystem. The bipartite entanglement properties of | ψ> are encoded in the spectrum of ρ A . By means of a saddle point method and using a "Coulomb gas" model for the eigenvalues, we obtain the typical spectrum of reduced density matrices. We consider the cases of an unbiased ensemble of pure states and of a fixed value of the purity. We finally obtain the eigenvalue distribution by using a statistical mechanics approach based on the introduction of a partition function.

  1. Multiple piece turbine rotor blade

    Science.gov (United States)

    Jones, Russell B; Fedock, John A

    2013-05-21

    A multiple piece turbine rotor blade with a shell having an airfoil shape and secured between a spar and a platform with the spar including a tip end piece. a snap ring fits around the spar and abuts against the spar tip end piece on a top side and abuts against a shell on the bottom side so that the centrifugal loads from the shell is passed through the snap ring and into the spar and not through a tip cap dovetail slot and projection structure.

  2. Typicals/Típicos

    Directory of Open Access Journals (Sweden)

    Silvia Vélez

    2004-01-01

    Full Text Available Typicals is a series of 12 colour photographs digitally created from photojournalistic images from Colombia combined with "typical" craft textiles and text from guest writers. Typicals was first exhibited as photographs 50cm x 75cm in size, each with their own magnifying glass, at the Contemporary Art Space at Gorman House in Canberra, Australia, in 2000. It was then exhibited in "Feedback: Art Social Consciousness and Resistance" at Monash University Museum of Art in Melbourne, Australia, from March to May 2003. From May to June 2003 it was exhibited at the Museo de Arte de la Universidad Nacional de Colombia Santa Fé Bogotá, Colombia. In its current manifestation the artwork has been adapted from the catalogue of the museum exhibitions. It is broken up into eight pieces corresponding to the contributions of the writers. The introduction by Sylvia Vélez is the PDF file accessible via a link below this abstract. The other seven PDF files are accessible via the 'Supplementary Files' section to the left of your screen. Please note that these files are around 4 megabytes each, so it may be difficult to access them from a dial-up connection.

  3. Push piece for spent fuel elements magazine

    International Nuclear Information System (INIS)

    Griveau, R.; Kerlau, D.; Tucoulat, D.; Colas, J.; Pellier, R.

    1989-01-01

    The push piece permits the displacement of little section elements in a magazine of high section. At the end of cut, the push piece leans its flank against an auxiliary blank holder and the element is pushed by a paddle, the push piece being immobilized [fr

  4. Do Puzzle Pieces and Autism Puzzle Piece Logos Evoke Negative Associations?

    Science.gov (United States)

    Gernsbacher, Morton Ann; Raimond, Adam R.; Stevenson, Jennifer L.; Boston, Jilana S.; Harp, Bev

    2018-01-01

    Puzzle pieces have become ubiquitous symbols for autism. However, puzzle-piece imagery stirs debate between those who support and those who object to its use because they believe puzzle-piece imagery evokes negative associations. Our study empirically investigated whether puzzle pieces evoke negative associations in the general public.…

  5. Devoluming and stabilizing method for end piece

    International Nuclear Information System (INIS)

    Ikeda, Satoshi; Shiotsuki, Msao; Kawamura, Shigeyoshi; Komatsu, Fumiaki.

    1991-01-01

    As a first method, end pieces and other radioactive metal wastes are filled as a mixture in a vessel, and preliminary compression is conducted. Then, the bulk density of the radioactive metal wastes is reduced and gaps in the end pieces are filled with radioactive metal wastes. If they are applied with heat treatment under high pressure in this state together with the vessel, they are devolumed and stabilized without damaging the vessel. As a second method, metal powders are mixed and filled in the vessel together with the end pieces. The gaps in the end pieces are filled with the metal powders and if they are applied with heat treatment under high pressure in this state together with the vessel, the end pieces are devolumed and stabilized without damaging the vessel in the same manner. This can devolume and stabilize the end pieces separated from nuclear fuel assemblies easily and safely. (T.M.)

  6. Optimization of Process Parameters During End Milling and Prediction of Work Piece Temperature Rise

    Directory of Open Access Journals (Sweden)

    Bhirud N.L.

    2017-09-01

    Full Text Available During the machining processes, heat gets generated as a result of plastic deformation of metal and friction along the tool–chip and tool–work piece interface. In materials having high thermal conductivity, like aluminium alloys, large amount of this heat is absorbed by the work piece. This results in the rise in the temperature of the work piece, which may lead to dimensional inaccuracies, surface damage and deformation. So, it is needed to control rise in the temperature of the work piece. This paper focuses on the measurement, analysis and prediction of work piece temperature rise during the dry end milling operation of Al 6063. The control factors used for experimentation were number of flutes, spindle speed, depth of cut and feed rate. The Taguchi method was employed for the planning of experimentation and L18 orthogonal array was selected. The temperature rise of the work piece was measured with the help of K-type thermocouple embedded in the work piece. Signal to noise (S/N ratio analysis was carried out using the lower-the-better quality characteristics. Depth of cut was identified as the most significant factor affecting the work piece temperature rise, followed by spindle speed. Analysis of variance (ANOVA was employed to find out the significant parameters affecting the work piece temperature rise. ANOVA results were found to be in line with the S/N ratio analysis. Regression analysis was used for developing empirical equation of temperature rise. The temperature rise of the work piece was calculated using the regression equation and was found to be in good agreement with the measured values. Finally, confirmation tests were carried out to verify the results obtained. From the confirmation test it was found that the Taguchi method is an effective method to determine optimised parameters for minimization of work piece temperature.

  7. Last piece of ATLAS takes the plunge

    CERN Multimedia

    2008-01-01

    On Friday 29 February the second small wheel was lowered 100 metres underground into the ATLAS cavern in front of a captivated audience. Although called the "small wheels" they are small in name only - each wheel is 9.3 metres in diameter and weighs 100 tonnes including the massive shielding elements. This piece completes ATLAS’ muon spectrometer, which has the ability to accurately track particles to the width of a human hair. The first piece of ATLAS was installed in 2003 and, five years later, this small wheel is the final large piece of the detector to take the subterranean voyage to its final resting place.

  8. Implant Gigi One-Piece vs Two-Pieces dalam Praktek Sehari-Hari

    Directory of Open Access Journals (Sweden)

    Dian Lestari Kurnia

    2014-12-01

    prosedur bedah dan prosedur prostetik lebih sederhana. Desain ini juga meniadakan celah mikro pada perbatasan implant dan abutment. Desain implant gigi one-piece memiliki keterbatasan pada pilihan prosedur prostetik apabila dibandingkan dengan desain implant gigi two-pieces.   One-Piece Versus Two-pieces Tooth Implant In Daily Practice. Implant had been a gold standard to replace missing tooth. However, implant marketed today was considered complex, and needs a second surgery. Complications may occur such as screw loosening or fracture and the presence of micro gap at implant-abutment-junction that is found causing fixture failure. The one-piece-implant design may offer some advantages. Purpose: this paper was aimed to discuss the pros and cons of one-piece-implants and two-piece-implants. Case 1 A 43-year-old woman came to place an implant on #16. The available bone height was 5 mm. A trans alveolar sinus lift procedure was performed with 0,5 cc allograft. A 12 mm one-piece-implant was inserted. Case 2 A 24-year-old woman came to place an implant on #46. The available bone height was 12 mm and a 10 mm two-piece-implant was inserted. Discussion: One-piece-implant offers some advantage. It needs no second surgery, easier placement protocol, and more natural prosthetic procedures. The design is preventing the failure in implant-abutment-junction failure. The absence of micro gap in one-piece-implant seems superior in preventing crestal bone resorption. However, the prosthetic option was limited in one-piece-implant. Two-piece-implant offers more choices in prosthetic abutment. Conclusion: One-piece-implant was easier and provide simple protocol with limited choice on prosthetic.

  9. Plastic Surgery

    Science.gov (United States)

    ... Staying Safe Videos for Educators Search English Español Plastic Surgery KidsHealth / For Teens / Plastic Surgery What's in ... her forehead lightened with a laser? What Is Plastic Surgery? Just because the name includes the word " ...

  10. Plasticity theory

    CERN Document Server

    Lubliner, Jacob

    2008-01-01

    The aim of Plasticity Theory is to provide a comprehensive introduction to the contemporary state of knowledge in basic plasticity theory and to its applications. It treats several areas not commonly found between the covers of a single book: the physics of plasticity, constitutive theory, dynamic plasticity, large-deformation plasticity, and numerical methods, in addition to a representative survey of problems treated by classical methods, such as elastic-plastic problems, plane plastic flow, and limit analysis; the problem discussed come from areas of interest to mechanical, structural, and

  11. Last piece of the puzzle for ATLAS

    CERN Multimedia

    Clare Ryan

    At around 15.40 on Friday 29th February the ATLAS collaboration cracked open the champagne as the second of the small wheels was lowered into the cavern. Each of ATLAS' small wheels are 9.3 metres in diameter and weigh 100 tonnes including the massive shielding elements. They are the final parts of ATLAS' muon spectrometer. The first piece of ATLAS was installed in 2003 and since then many detector elements have journeyed down the 100 metre shaft into the ATLAS underground cavern. This last piece completes this gigantic puzzle.

  12. 76 FR 55708 - Servicing Multi-Piece and Single Piece Rim Wheels; Extension of the Office of Management and...

    Science.gov (United States)

    2011-09-08

    ...] Servicing Multi-Piece and Single Piece Rim Wheels; Extension of the Office of Management and Budget's (OMB... concerning its proposal to extend the Office of Management and Budget's (OMB) approval of the information collection requirements specified in the Standard on Servicing Multi-Piece and Single Piece Rim Wheels (29...

  13. A one-step strategy for ultra-fast and low-cost mass production of plastic membrane microfluidic chips.

    Science.gov (United States)

    Hu, Chong; Lin, Sheng; Li, Wanbo; Sun, Han; Chen, Yangfan; Chan, Chiu-Wing; Leung, Chung-Hang; Ma, Dik-Lung; Wu, Hongkai; Ren, Kangning

    2016-10-05

    An ultra-fast, extremely cost-effective, and environmentally friendly method was developed for fabricating flexible microfluidic chips with plastic membranes. With this method, we could fabricate plastic microfluidic chips rapidly (within 12 seconds per piece) at an extremely low cost (less than $0.02 per piece). We used a heated perfluoropolymer perfluoroalkoxy (often called Teflon PFA) solid stamp to press a pile of two pieces of plastic membranes, low density polyethylene (LDPE) and polyethylene terephthalate (PET) coated with an ethylene-vinyl acetate copolymer (EVA). During the short period of contact with the heated PFA stamp, the pressed area of the membranes permanently bonded, while the LDPE membrane spontaneously rose up at the area not pressed, forming microchannels automatically. These two regions were clearly distinguishable even at the micrometer scale so we were able to fabricate microchannels with widths down to 50 microns. This method combines the two steps in the conventional strategy for microchannel fabrication, generating microchannels and sealing channels, into a single step. The production is a green process without using any solvent or generating any waste. Also, the chips showed good resistance against the absorption of Rhodamine 6G, oligonucleotides, and green fluorescent protein (GFP). We demonstrated some typical microfluidic manipulations with the flexible plastic membrane chips, including droplet formation, on-chip capillary electrophoresis, and peristaltic pumping for quantitative injection of samples and reagents. In addition, we demonstrated convenient on-chip detection of lead ions in water samples by a peristaltic-pumping design, as an example of the application of the plastic membrane chips in a resource-limited environment. Due to the high speed and low cost of the fabrication process, this single-step method will facilitate the mass production of microfluidic chips and commercialization of microfluidic technologies.

  14. Implant Gigi One-Piece vs Two-Pieces dalam Praktek Sehari-Hari

    OpenAIRE

    Kurnia, Dian Lestari; Ramadhani, Amilia; Hudyono, Rikko

    2014-01-01

    Saat ini, implant merupakan pilihan terbaik untuk menggantikan gigi yang tanggal, akan tetapi prosedur pemasangannya terbilang rumit dan memerlukan prosedur bedah kedua untuk pemasangan prostetik. Beberapa komplikasi seperti screw patah atau longgar dan adanya celah mikro pada batas pertemuan implant dan abutment dapat menyebabkan kegagalan implant. Studi kasus ini bertujuan untuk membahas mengenai keuntungan dan kerugian desain implant gigi one-piece dan two-pieces. Kasus pertama, seorang wa...

  15. Implant Gigi One-Piece Vs Two-Pieces Dalam Praktek Sehari-Hari

    OpenAIRE

    Kurnia, Dian Lestari; Ramadhani, Amilia; Hudyono, Rikko

    2014-01-01

    Saat ini, implant merupakan pilihan terbaik untuk menggantikan gigi yang tanggal, akan tetapi prosedur pemasangannya terbilang rumit dan memerlukan prosedur bedah kedua untuk pemasangan prostetik. Beberapa komplikasi seperti screw patah atau longgar dan adanya celah mikro pada batas pertemuan implant dan abutment dapat menyebabkan kegagalan implant. Studi kasus ini bertujuan untuk membahas mengenai keuntungan dan kerugian desain implant gigi one-piece dan two-pieces. Kasus pertama, seorang wa...

  16. Is our Universe typical?

    International Nuclear Information System (INIS)

    Gurzadyan, V.G.

    1988-01-01

    The problem of typicalness of the Universe - as a dynamical system possessing both regular and chaotic regions of positive measure of phase space, is raised and discussed. Two dynamical systems are considered: 1) The observed Universe as a hierarchy of systems of N graviting bodies; 2) (3+1)-manifold with matter evolving to Wheeler-DeWitt equation in superspace with Hawking boundary condition of compact metrics. It is shown that the observed Universe is typical. There is no unambiguous answer for the second system yet. If it is typical too then the same present state of the Universe could have been originated from an infinite number of different initial conditions the restoration of which is practically impossible at present. 35 refs.; 2 refs

  17. Surface dimpling on rotating work piece using rotation cutting tool

    Science.gov (United States)

    Bhapkar, Rohit Arun; Larsen, Eric Richard

    2015-03-31

    A combined method of machining and applying a surface texture to a work piece and a tool assembly that is capable of machining and applying a surface texture to a work piece are disclosed. The disclosed method includes machining portions of an outer or inner surface of a work piece. The method also includes rotating the work piece in front of a rotating cutting tool and engaging the outer surface of the work piece with the rotating cutting tool to cut dimples in the outer surface of the work piece. The disclosed tool assembly includes a rotating cutting tool coupled to an end of a rotational machining device, such as a lathe. The same tool assembly can be used to both machine the work piece and apply a surface texture to the work piece without unloading the work piece from the tool assembly.

  18. Contrast enhancement of mail piece images

    Science.gov (United States)

    Shin, Yong-Chul; Sridhar, Ramalingam; Demjanenko, Victor; Palumbo, Paul W.; Hull, Jonathan J.

    1992-08-01

    A New approach to contrast enhancement of mail piece images is presented. The contrast enhancement is used as a preprocessing step in the real-time address block location (RT-ABL) system. The RT-ABL system processes a stream of mail piece images and locates destination address blocks. Most of the mail pieces (classified into letters) show high contrast between background and foreground. As an extreme case, however, the seasonal greeting cards usually use colored envelopes which results in reduced contrast osured by an error rate by using a linear distributed associative memory (DAM). The DAM is trained to recognize the spectra of three classes of images: with high, medium, and low OCR error rates. The DAM is not forced to make a classification every time. It is allowed to reject as unknown a spectrum presented that does not closely resemble any that has been stored in the DAM. The DAM was fairly accurate with noisy images but conservative (i.e., rejected several text images as unknowns) when there was little ground and foreground degradations without affecting the nondegraded images. This approach provides local enhancement which adapts to local features. In order to simplify the computation of A and (sigma) , dynamic programming technique is used. Implementation details, performance, and the results on test images are presented in this paper.

  19. Typical Complexity Numbers

    Indian Academy of Sciences (India)

    First page Back Continue Last page Overview Graphics. Typical Complexity Numbers. Say. 1000 tones,; 100 Users,; Transmission every 10 msec. Full Crosstalk cancellation would require. Full cancellation requires a matrix multiplication of order 100*100 for all the tones. 1000*100*100*100 operations every second for the ...

  20. Modeling The Interaction Effects Between Tools And The Work Piece For Metal Forming Processes

    International Nuclear Information System (INIS)

    Franzke, Martin; Puchhala, Sreedhar; Dackweiler, Harald

    2007-01-01

    In metal forming processes especially in cold forming, elastic deformation of the tools has a big impact on the final shape of the work-piece. Computation of such processes considering the plastic effects of the work-piece and elastic deformations of the tools at a time in a single FE model complicates to manage the convergence criteria. This situation is even aggravated if the contact situations (between working and support rolls) have to be considered in the simulation, which requires a very fine discretization of the contact zones of both the tool and work piece. This paper presents recently developed concept which meets the above mentioned demands very effectively. Within this concept, the computation of the elastic effects of the tools is separated from the process simulation (which considers elastic-plastic effects of the work-piece). Both simulations are coupled via automatic data interchange, which is bi-directional, because both simulations influence each other. The advantages of this concept include a quite easy to handle contact situations in process simulation, smaller stiffness matrix compared to single model approach and good convergence of the computation. This concept is highly generalized and successfully applied to simulate rolling, drawing, extrusion and forging processes. The above mentioned concept is being implemented into the FE package PEP and LARSTRAN/SHAPE. Rolling experiments are conducted in duo and quarto configuration. Optical three-dimensional digitalizing system was used to measure the deformations within the machine and work-piece profile. These results are used for the validation of FE simulations. This work is being sponsored by the German Research Foundation (DFG) through the project ''Interaction effects between processes and structures-SPP1180''

  1. Biodegradability of Plastics: Challenges and Misconceptions.

    Science.gov (United States)

    Kubowicz, Stephan; Booth, Andy M

    2017-11-07

    Plastics are one of the most widely used materials and, in most cases, they are designed to have long life times. Thus, plastics contain a complex blend of stabilizers that prevent them from degrading too quickly. Unfortunately, many of the most advantageous properties of plastics such as their chemical, physical and biological inertness and durability present challenges when plastic is released into the environment. Common plastics such as polyethylene (PE), polypropylene (PP), polystyrene (PS), and polyethylene terephthalate (PET) are extremely persistent in the environment, where they undergo very slow fragmentation (projected to take centuries) into small particles through photo-, physical, and biological degradation processes 1 . The fragmentation of the material into increasingly smaller pieces is an unavoidable stage of the degradation process. Ultimately, plastic materials degrade to micron-sized particles (microplastics), which are persistent in the environment and present a potential source of harm for organisms.

  2. Direct liquefaction of plastics and coprocessing of coal with plastics

    Energy Technology Data Exchange (ETDEWEB)

    Huffman, G.P.; Feng, Z.; Mahajan, V. [Univ. of Kentucky, Lexington, KY (United States)

    1995-12-31

    The objectives of this work were to optimize reaction conditions for the direct liquefaction of waste plastics and the coprocessing of coal with waste plastics. In previous work, the direct liquefaction of medium and high density polyethylene (PE), polypropylene (PPE), poly(ethylene terephthalate) (PET), and a mixed plastic waste, and the coliquefaction of these plastics with coals of three different ranks was studied. The results established that a solid acid catalyst (HZSM-5 zeolite) was highly active for the liquefaction of the plastics alone, typically giving oil yields of 80-95% and total conversions of 90-100% at temperatures of 430-450 {degrees}C. In the coliquefaction experiments, 50:50 mixtures of plastic and coal were used with a tetralin solvent (tetralin:solid = 3:2). Using approximately 1% of the HZSM-5 catalyst and a nanoscale iron catalyst, oil yields of 50-70% and total conversion of 80-90% were typical. In the current year, further investigations were conducted of the liquefaction of PE, PPE, and a commingled waste plastic obtained from the American Plastics Council (APC), and the coprocessing of PE, PPE and the APC plastic with Black Thunder subbituminous coal. Several different catalysts were used in these studies.

  3. Use of Plastic Mulch for Vegetable Production

    OpenAIRE

    Maughan, Tiffany; Drost, Dan

    2016-01-01

    Plastic mulches are used commercially for both vegetables and small fruit crops. Vegetable crops well suited for production with plastic mulch are typically high value row crops. This fact sheet describes the advantages, disadvantages, installation, and planting considerations. It includes sources for plastic and equipment.

  4. Isolation of native soil microorganisms with potential for breaking down biodegradable plastic mulch films used in agriculture.

    Science.gov (United States)

    Bailes, Graham; Lind, Margaret; Ely, Andrew; Powell, Marianne; Moore-Kucera, Jennifer; Miles, Carol; Inglis, Debra; Brodhagen, Marion

    2013-05-10

    Fungi native to agricultural soils that colonized commercially available biodegradable mulch (BDM) films were isolated and assessed for potential to degrade plastics. Typically, when formulations of plastics are known and a source of the feedstock is available, powdered plastic can be suspended in agar-based media and degradation determined by visualization of clearing zones. However, this approach poorly mimics in situ degradation of BDMs. First, BDMs are not dispersed as small particles throughout the soil matrix. Secondly, BDMs are not sold commercially as pure polymers, but rather as films containing additives (e.g. fillers, plasticizers and dyes) that may affect microbial growth. The procedures described herein were used for isolates acquired from soil-buried mulch films. Fungal isolates acquired from excavated BDMs were tested individually for growth on pieces of new, disinfested BDMs laid atop defined medium containing no carbon source except agar. Isolates that grew on BDMs were further tested in liquid medium where BDMs were the sole added carbon source. After approximately ten weeks, fungal colonization and BDM degradation were assessed by scanning electron microscopy. Isolates were identified via analysis of ribosomal RNA gene sequences. This report describes methods for fungal isolation, but bacteria also were isolated using these methods by substituting media appropriate for bacteria. Our methodology should prove useful for studies investigating breakdown of intact plastic films or products for which plastic feedstocks are either unknown or not available. However our approach does not provide a quantitative method for comparing rates of BDM degradation.

  5. Isolation of Native Soil Microorganisms with Potential for Breaking Down Biodegradable Plastic Mulch Films Used in Agriculture

    Science.gov (United States)

    Bailes, Graham; Lind, Margaret; Ely, Andrew; Powell, Marianne; Moore-Kucera, Jennifer; Miles, Carol; Inglis, Debra; Brodhagen, Marion

    2013-01-01

    Fungi native to agricultural soils that colonized commercially available biodegradable mulch (BDM) films were isolated and assessed for potential to degrade plastics. Typically, when formulations of plastics are known and a source of the feedstock is available, powdered plastic can be suspended in agar-based media and degradation determined by visualization of clearing zones. However, this approach poorly mimics in situ degradation of BDMs. First, BDMs are not dispersed as small particles throughout the soil matrix. Secondly, BDMs are not sold commercially as pure polymers, but rather as films containing additives (e.g. fillers, plasticizers and dyes) that may affect microbial growth. The procedures described herein were used for isolates acquired from soil-buried mulch films. Fungal isolates acquired from excavated BDMs were tested individually for growth on pieces of new, disinfested BDMs laid atop defined medium containing no carbon source except agar. Isolates that grew on BDMs were further tested in liquid medium where BDMs were the sole added carbon source. After approximately ten weeks, fungal colonization and BDM degradation were assessed by scanning electron microscopy. Isolates were identified via analysis of ribosomal RNA gene sequences. This report describes methods for fungal isolation, but bacteria also were isolated using these methods by substituting media appropriate for bacteria. Our methodology should prove useful for studies investigating breakdown of intact plastic films or products for which plastic feedstocks are either unknown or not available. However our approach does not provide a quantitative method for comparing rates of BDM degradation. PMID:23712218

  6. Typicality and reasoning fallacies.

    Science.gov (United States)

    Shafir, E B; Smith, E E; Osherson, D N

    1990-05-01

    The work of Tversky and Kahneman on intuitive probability judgment leads to the following prediction: The judged probability that an instance belongs to a category is an increasing function of the typicality of the instance in the category. To test this prediction, subjects in Experiment 1 read a description of a person (e.g., "Linda is 31, bright, ... outspoken") followed by a category. Some subjects rated how typical the person was of the category, while others rated the probability that the person belonged to that category. For categories like bank teller and feminist bank teller: (1) subjects rated the person as more typical of the conjunctive category (a conjunction effect); (2) subjects rated it more probable that the person belonged to the conjunctive category (a conjunction fallacy); and (3) the magnitudes of the conjunction effect and fallacy were highly correlated. Experiment 2 documents an inclusion fallacy, wherein subjects judge, for example, "All bank tellers are conservative" to be more probable than "All feminist bank tellers are conservative." In Experiment 3, results parallel to those of Experiment 1 were obtained with respect to the inclusion fallacy.

  7. Development of debris resistant bottom end piece

    International Nuclear Information System (INIS)

    Lee, Jae Kyung; Sohn, Dong Seong; Yim, Jeong Sik; Hwang, Dae Hyun; Song, Kee Nam; Oh, Dong Seok; Rhu, Ho Sik; Lee, Chang Woo; Kim, Seong Soo; Oh, Jong Myung

    1993-12-01

    Debris-related fuel failures have been identified as one of the major causes of fuel failures. In order to reduce the possibility of debris-related fuel failures, it is necessary to develop Debris-Resistant Bottom End Piece. For this development, mechanical strength test and pressure drop test were performed, and the test results were analyzed. And the laser cutting, laser welding and electron beam welding technology, which were the core manufacturing technology of DRBEP, were developed. Final design were performed, and the final drawing and specifications were prepared. The prototype of DRBEP was manufactured according to the developed munufacturing procedure. (Author)

  8. Plastic deformation of 2D crumpled wires

    International Nuclear Information System (INIS)

    Gomes, M A F; Donato, C C; Brito, V P; Coelho, A S O

    2008-01-01

    When a single long piece of elastic wire is injected through channels into a confining two-dimensional cavity, a complex structure of hierarchical loops is formed. In the limit of maximum packing density, these structures are described by several scaling laws. In this paper this packing process is investigated but using plastic wires which give rise to completely irreversible structures of different morphology. In particular, the plastic deformation from circular to oblate configurations of crumpled wires is experimentally studied, obtained by the application of an axial strain. Among other things, it is shown that in spite of plasticity, irreversibility and very large deformations, scaling is still observed.

  9. Dissolved organic carbon leaching from plastics stimulates microbial activity in the ocean

    NARCIS (Netherlands)

    Romera-Castillo, C.; Pinto, M.; Langer, T.M.; Alvarez-Salgado, X.A.; Herndl, G.

    2018-01-01

    Approximately 5.25 trillion plastic pieces are floating at the sea surface. The impact of plastic pollution on the lowest trophic levels of the food web, however, remains unknown. Here we show that plastics release dissolved organic carbon (DOC) into the ambient seawater stimulating the activity of

  10. Note onset deviations as musical piece signatures.

    Science.gov (United States)

    Serrà, Joan; Özaslan, Tan Hakan; Arcos, Josep Lluis

    2013-01-01

    A competent interpretation of a musical composition presents several non-explicit departures from the written score. Timing variations are perhaps the most important ones: they are fundamental for expressive performance and a key ingredient for conferring a human-like quality to machine-based music renditions. However, the nature of such variations is still an open research question, with diverse theories that indicate a multi-dimensional phenomenon. In the present study, we consider event-shift timing variations and show that sequences of note onset deviations are robust and reliable predictors of the musical piece being played, irrespective of the performer. In fact, our results suggest that only a few consecutive onset deviations are already enough to identify a musical composition with statistically significant accuracy. We consider a mid-size collection of commercial recordings of classical guitar pieces and follow a quantitative approach based on the combination of standard statistical tools and machine learning techniques with the semi-automatic estimation of onset deviations. Besides the reported results, we believe that the considered materials and the methodology followed widen the testing ground for studying musical timing and could open new perspectives in related research fields.

  11. Note onset deviations as musical piece signatures.

    Directory of Open Access Journals (Sweden)

    Joan Serrà

    Full Text Available A competent interpretation of a musical composition presents several non-explicit departures from the written score. Timing variations are perhaps the most important ones: they are fundamental for expressive performance and a key ingredient for conferring a human-like quality to machine-based music renditions. However, the nature of such variations is still an open research question, with diverse theories that indicate a multi-dimensional phenomenon. In the present study, we consider event-shift timing variations and show that sequences of note onset deviations are robust and reliable predictors of the musical piece being played, irrespective of the performer. In fact, our results suggest that only a few consecutive onset deviations are already enough to identify a musical composition with statistically significant accuracy. We consider a mid-size collection of commercial recordings of classical guitar pieces and follow a quantitative approach based on the combination of standard statistical tools and machine learning techniques with the semi-automatic estimation of onset deviations. Besides the reported results, we believe that the considered materials and the methodology followed widen the testing ground for studying musical timing and could open new perspectives in related research fields.

  12. 29 CFR 1910.177 - Servicing multi-piece and single piece rim wheels.

    Science.gov (United States)

    2010-07-01

    ...” and “Multi-piece Rim Matching Chart,” or any other poster which contains at least the same... procedure shall include at least the following elements: (1) Tires shall be completely deflated before... and follow that procedure. The procedure shall include at least the following elements: (1) Tires...

  13. Fractal dimension analysis of complexity in Ligeti piano pieces

    Science.gov (United States)

    Bader, Rolf

    2005-04-01

    Fractal correlation dimensional analysis has been performed with whole solo piano pieces by Gyrgy Ligeti at every 50ms interval of the pieces. The resulting curves of development of complexity represented by the fractal dimension showed up a very reasonable correlation with the perceptional density of events during these pieces. The seventh piece of Ligeti's ``Musica ricercata'' was used as a test case. Here, each new part of the piece was followed by an increase of the fractal dimension because of the increase of information at the part changes. The second piece ``Galamb borong,'' number seven of the piano Etudes was used, because Ligeti wrote these Etudes after studying fractal geometry. Although the piece is not fractal in the strict mathematical sense, the overall structure of the psychoacoustic event-density as well as the detailed event development is represented by the fractal dimension plot.

  14. Two-piece hollow bulb obturator

    Directory of Open Access Journals (Sweden)

    Subramaniam Elangovan

    2011-01-01

    Full Text Available There are various types of obturator fabrication achievable by prosthodontist. Maxillectomy, which is a term used by head and neck surgeons and prosthodontists to describe the partial or total removal of the maxilla in patients suffering from benign or malignant neoplasms is a defect for which to provide an effective obturator is a difficult task for the maxillofacial prosthodontist. Multidisciplinary treatment planning is essential to achieve adequate retention and function for the prosthesis. Speech is often unintelligible as a result of the marked defects in articulation and nasal resonance. This paper describes how to achieve the goal for esthetics and phonetics and also describes the fabrication of a hollow obturator by two piece method, which is simple and maybe used as definitive obturator for maximum comfort of the patient.

  15. A new piece of the puzzle

    CERN Multimedia

    2005-01-01

    The team responsible for the installation of the hadronic calorimeter's central barrel after completion of the assembly work. Assembly of the great ATLAS puzzle continues underground. On 10 December, the final module of the central barrel of the tile hadronic calorimeter was assembled. This piece of the tile calorimeter had already been assembled above ground during a "dress rehearsal" in 2003 (see Bulletin no 46/2003, 10 November 2003). The hadronic calorimeter's two other barrels, the so-called "extended barrels", remain to be assembled with this first central barrel, which now surrounds the electromagnetic calorimeter barrel that was lowered into the cavern at the end of October. At the end of November, the second of the eight barrel toroid coils was also installed.

  16. Exfoliation syndrome: assembling the puzzle pieces.

    Science.gov (United States)

    Pasquale, Louis R; Borrás, Terete; Fingert, John H; Wiggs, Janey L; Ritch, Robert

    2016-09-01

    To summarize various topics and the cutting edge approaches to refine XFS pathogenesis that were discussed at the 21st annual Glaucoma Foundation Think Tank meeting in New York City, Sept. 19-20, 2014. The highlights of three categories of talks on cutting edge research in the field were summarized. Exfoliation syndrome (XFS) is a systemic disorder with a substantial ocular burden, including high rates of cataract, cataract surgery complications, glaucoma and retinal vein occlusion. New information about XFS is akin to puzzle pieces that do not quite join together to reveal a clear picture regarding how exfoliation material (XFM) forms. Meeting participants concluded that it is unclear how the mild homocysteinemia seen in XFS might contribute to the disarrayed extracellular aggregates characteristic of this syndrome. Lysyl oxidase-like 1 (LOXL1) variants are unequivocally genetic risk factors for XFS but exactly how these variants contribute to the assembly of exfoliation material (XFM) remains unclear. Variants in a new genomic region, CACNA1A associated with XFS, may alter calcium concentrations at the cell surface and facilitate XFM formation but much more work is needed before we can place this new finding in proper context. It is hoped that various animal model and ex vivo systems will emerge that will allow for proper assembly of the puzzle pieces into a coherent picture of XFS pathogenesis. A clear understanding of XFS pathogenesis may lead to 'upstream solutions' to reduce the ocular morbidity produced by XFS. © 2015 Acta Ophthalmologica Scandinavica Foundation. Published by John Wiley & Sons Ltd.

  17. Utilization of the UV laser with picosecond pulses for the formation of surface microstructures on elastomeric plastics

    Science.gov (United States)

    Antoszewski, B.; Tofil, S.; Scendo, M.; Tarelnik, W.

    2017-08-01

    Elastomeric plastics belong to a wide range of polymeric materials with special properties. They are used as construction material for seals and other components in many branches of industry and, in particular, in the biomedical industry, mechatronics, electronics and chemical equipment. The micromachining of surfaces of these materials can be used to build micro-flow, insulating, dispensing systems and chemical and biological reactors. The paper presents results of research on the effects of micro-machining of selected elastomeric plastics using a UV laser emitting picosecond pulses. The authors see the prospective application of the developed technology in the sealing technique in particular to shaping the sealing pieces co-operating with the surface of the element. The result of the study is meant to show parameters of the UV laser’s performance when producing typical components such as grooves, recesses for optimum ablation in terms of quality and productivity.

  18. A Typical Synergy

    Science.gov (United States)

    van Noort, Thomas; Achten, Peter; Plasmeijer, Rinus

    We present a typical synergy between dynamic types (dynamics) and generalised algebraic datatypes (GADTs). The former provides a clean approach to integrating dynamic typing in a statically typed language. It allows values to be wrapped together with their type in a uniform package, deferring type unification until run time using a pattern match annotated with the desired type. The latter allows for the explicit specification of constructor types, as to enforce their structural validity. In contrast to ADTs, GADTs are heterogeneous structures since each constructor type is implicitly universally quantified. Unfortunately, pattern matching only enforces structural validity and does not provide instantiation information on polymorphic types. Consequently, functions that manipulate such values, such as a type-safe update function, are cumbersome due to boilerplate type representation administration. In this paper we focus on improving such functions by providing a new GADT annotation via a natural synergy with dynamics. We formally define the semantics of the annotation and touch on novel other applications of this technique such as type dispatching and enforcing type equality invariants on GADT values.

  19. Plastic dosimeter

    International Nuclear Information System (INIS)

    Nagai, Shiro; Matsuda, Kohji.

    1988-01-01

    The report outlines major features and applications of plastic dosimeters. Some plastic dosimeters, including the CTA and PVC types, detect the response of the plastic material itself to radiations while others, such as pigment-added plastic dosimeters, contain additives as radiation detecting material. Most of these dosimeters make use of color centers produced in the dosimeter by radiations. The PMMA dosimeter is widely used in the field of radiation sterilization of food, feed and medical apparatus. The blue cellophane dosimeter is easy to handle if calibrated appropriately. The rad-color dosimeter serves to determine whether products have been irradiated appropriately. The CTA dosimeter has better damp proofing properties than the blue cellophane type. The pigment-added plastic dosimeter consists of a resin such as nylon, CTA or PVC that contains a dye. Some other plastic dosimeters are also described briefly. Though having many advantages, these plastic dosimeter have disadvantages as well. Some of their major disadvantages, including fading as well as large dependence on dose, temperature, humidity and anviroment, are discussed. (Nogami, K.)

  20. Plastic and Non-plastic Debris Ingestion in Three Gull Species Feeding in an Urban Landfill Environment.

    Science.gov (United States)

    Seif, S; Provencher, J F; Avery-Gomm, S; Daoust, P-Y; Mallory, M L; Smith, P A

    2018-04-01

    Plastic debris is recognized as a widespread, common and problematic environmental pollutant. An important consequence of this pollution is the ingestion of plastic debris by wildlife. Assessing the degree to which different species ingest plastics, and the potential effects of these plastics on their health are important research needs for understanding the impacts of plastic pollution. We examined debris (plastic and other types) ingestion in three sympatric overwintering gull species (Herring gulls Larus smithsonianus, Great Black-backed Gulls Larus marinus, and Iceland Gulls Larus glaucoides) to understand how debris ingestion differs among species, age classes and sexes in gulls. We also assessed how plastic burdens were associated with body condition to investigate how gulls may be affected by debris ingestion. There were no differences among the species, age classes or sexes in the incidence of debris ingestion (plastic or otherwise), the mass or number of debris pieces ingested. We found no correlation between ingested plastics burdens and individual condition. Gulls ingested plastic debris, but also showed high levels of other debris types as well, including metal, glass and building materials, including a metal piece of debris found within an abscess in the stomach. Thus, when the health effects of debris ingestion on gulls, and other species that ingest debris, is of interest, either from a physical or chemical perspective, it may be necessary to consider all debris types and not just plastic burdens as is often currently done for seabirds.

  1. PLASTIC SURGERY

    African Journals Online (AJOL)

    Department of Plastic and Reconstructive Surgery Sefako Makgatho Health Science University, ... We report on a pilot study on the use of a circumareolar excision and the use of .... and 1 gynecomastia patient) requested reduction in NAC size.

  2. Plastic Fishes

    CERN Multimedia

    Trettnak, Wolfgang

    2015-01-01

    In terms of weight, the plastic pollution in the world’s oceans is estimated to be around 300,000 tonnes. This plastic comes from both land-based and ocean-based sources. A lecture at CERN by chemist Wolfgang Trettnak addressed this issue and highlighted the role of art in raising people’s awareness. The slideshow below gives you a taste of the artworks by Wolfgang Trettnak and Margarita Cimadevila.

  3. Low-cost rapid prototyping of flexible plastic paper based microfluidic devices

    KAUST Repository

    Fan, Yiqiang; Li, Huawei; Yi, Ying; Foulds, Ian G.

    2013-01-01

    This research presents a novel rapid prototyping method for paper-based flexible microfluidic devices. The microchannels were fabricated using laser ablation on a piece of plastic paper (permanent paper), the dimensions of the microchannels

  4. Model Checking in Bits and Pieces

    Directory of Open Access Journals (Sweden)

    Kedar S. Namjoshi

    2013-09-01

    Full Text Available Fully automated verification of concurrent programs is a difficult problem, primarily because of state explosion: the exponential growth of a program state space with the number of its concurrently active components. It is natural to apply a divide and conquer strategy to ameliorate state explosion, by analyzing only a single component at a time. We show that this strategy leads to the notion of a "split" invariant, an assertion which is globally inductive, while being structured as the conjunction of a number of local, per-component invariants. This formulation is closely connected to the classical Owicki-Gries method and to Rely-Guarantee reasoning. We show how the division of an invariant into a number of pieces with limited scope makes it possible to apply new, localized forms of symmetry and abstraction to drastically simplify its computation. Split invariance also has interesting connections to parametric verification. A quantified invariant for a parametric system is a split invariant for every instance. We show how it is possible, in some cases, to invert this connection, and to automatically generalize from a split invariant for a small instance of a system to a quantified invariant which holds for the entire family of instances.

  5. The last piece of the ring

    CERN Multimedia

    2008-01-01

    In a sequel to the recent success at CMS, the last section of the LHC beam vacuum system was installed in ATLAS on Monday 16 June. The place where experiment and accelerator meet, the completion of the last part of the continuous 27 km beampipe signals how near the LHC is to the circulation of its first beam. Watch the video! The last section of the LHC beampipe being installed in ATLAS.Although a seemingly simple piece of technology in comparison with the complexity of the detectors, the beampipe is a carefully designed and essential part of both the experiments and the LHC. The section of beam pipe that completed the LHC ring on Monday 16 June is about 20 metres from the centre of ATLAS, very close to where the first magnets of the LHC are located. Unlike the central ATLAS beampipe, which is made of beryllium, the final section is made of stainless steel. An aluminium cone surrounds the stainless steel tube with the super slim...

  6. [Study on quality standards of decoction pieces of salt Alpinia].

    Science.gov (United States)

    Li, Wenbing; Hu, Changjiang; Long, Lanyan; Huang, Qinwan; Xie, Xiuqiong

    2010-12-01

    To establish the quality criteria for decoction pieces of salt Alpinia. Decoction pieces of salt Alpinia were measured with moisture, total ash, acid-insoluble ash, water-extract and volatile oils according to the procedures recorded in the Chinese Pharmacopoeia 2010. The content of Nootkatone was determined by HPLC, and NaCl, by chloridion electrode method. We obtained results of total ash, acid-insoluble ash, water-extract and volatile oils of 10 batches of decoction pieces of salt Alpinia moisture; Meanwhile we set the HPLC and chloridion electrode method. This research established a fine quality standard for decoction pieces of salt Alpinia.

  7. Underwater transporting method and device for incore structure cutting piece

    International Nuclear Information System (INIS)

    Kurosawa, Koichi; Chiba, Noboru; Chiba, Isao; Takada, Hiroshi; Furukawa, Hideyasu; Chiba, Noboru.

    1996-01-01

    Cutting pieces are handled by using a pick-up device connected with a wire ropes, a take-up drum, chains and a winch as cutting piece handling means, and moved freely on the water surface by a propulsion machine of a transporting means of the device to transfer them under water to a predetermined position. The pick-up device is lifted by taking-up the rope by the rotation of the take-up drum using chain-driving by way of the winch and the chains. The cut pieces are stored in a cask by lowering them in the cask and releasing the handling. In addition, if the weight of the cut pieces is recognized before cutting, and the load of the weight of the cut pieces is applied to the device previously, the balance of the device and the cut pieces can be kept, and cut pieces can be transported under water always stably. Further, if the cut pieces are supported upon cutting operation, the cut pieces are made stable, and cutting operation with good efficiency can be attained. (N.H.)

  8. Spatial distribution, input and dispersion of plastic pellets in coastal zones

    OpenAIRE

    Danilo Balthazar Silva

    2016-01-01

    The production and the usage of plastic material increases since the decade of 1950. Nowadays, the elevated production rate, the misusing and the waste turned plastic material in an urgent environmental and economic problem. One of the major environmental problems related to this issue is the contamination of marine environments by microplastics. These constitute plastic particles of size between 1 and 5 mm. Microplastics might occur by breaking of larger plastic pieces or as a manufactured p...

  9. GREEN PLASTIC: A NEW PLASTIC FOR PACKAGING

    OpenAIRE

    Mr. Pankaj Kumar*, Sonia

    2016-01-01

    This paper gives a brief idea about a new type of plastic called as bio-plastic or green plastic. Plastic is used as a packaging material for various products, but this plastic is made up of non renewable raw materials. There are various disadvantages of using conventional plastic like littering, CO2 production, non-degradable in nature etc. To overcome these problems a new type of plastic is discovered called bio-plastic or green plastic. Bio-plastic is made from renewable resources and also...

  10. Plastic condoms.

    Science.gov (United States)

    1968-01-01

    Only simple equipment, simple technology and low initial capital investment are needed in their manufacture. The condoms can be made by people who were previously unskilled or only semi-skilled workers. Plastic condoms differ from those made of latex rubber in that the nature of the plastic film allows unlimited shelf-life. Also, the plastic has a higher degree of lubricity than latex rubber; if there is a demand for extra lubrication in a particular market, this can be provided. Because the plastic is inert, these condoms need not be packaged in hermetically sealed containers. All these attributes make it possible to put these condoms on the distributors' shelves in developing countries competitively with rubber condoms. The shape of the plastic condom is based on that of the lamb caecum, which has long been used as luxury-type condom. The plastic condom is made from plastic film (ethylene ethyl acrilate) of 0.001 inch (0.0254 mm.) thickness. In addition, a rubber ring is provided and sealed into the base of the condom for retention during coitus. The advantage of the plastic condom design and the equipment on which it is made is that production can be carried out either in labour-intensive economy or with varying degrees of mechanization and automation. The uniform, finished condom if made using previously untrained workers. Training of workers can be done in a matter of hours on the two machines which are needed to produce and test the condoms. The plastic film is provided on a double wound roll, and condom blanks are prepared by means of a heat-sealing die on the stamping machine. The rubber rings are united to the condom blanks on an assembly machine, which consists of a mandrel and heat-sealing equipment to seal the rubber ring to the base of the condom. Built into the assembly machine is a simple air-testing apparatus that can detect the smallest pinhole flaw in a condom. The manufacturing process is completed by unravelling the condom from the assembly

  11. A Piece of Paper Falling Faster than Free Fall

    Science.gov (United States)

    Vera, F.; Rivera, R.

    2011-01-01

    We report a simple experiment that clearly demonstrates a common error in the explanation of the classic experiment where a small piece of paper is put over a book and the system is let fall. This classic demonstration is used in introductory physics courses to show that after eliminating the friction force with the air, the piece of paper falls…

  12. 7 CFR 51.1435 - U.S. Commercial Pieces.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false U.S. Commercial Pieces. 51.1435 Section 51.1435 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards... STANDARDS) United States Standards for Grades of Shelled Pecans Grades § 51.1435 U.S. Commercial Pieces. The...

  13. 75 FR 28051 - Public Workshop: Pieces of Privacy

    Science.gov (United States)

    2010-05-19

    ... DEPARTMENT OF HOMELAND SECURITY Office of the Secretary Public Workshop: Pieces of Privacy AGENCY: Privacy Office, DHS. ACTION: Notice announcing public workshop. SUMMARY: The Department of Homeland Security Privacy Office will host a public workshop, ``Pieces of Privacy.'' DATES: The workshop will be...

  14. Nano-plastics in the aquatic environment.

    Science.gov (United States)

    Mattsson, K; Hansson, L-A; Cedervall, T

    2015-10-01

    The amount of plastics released to the environment in modern days has increased substantially since the development of modern plastics in the early 1900s. As a result, concerns have been raised by the public about the impact of plastics on nature and on, specifically, aquatic wildlife. Lately, much attention has been paid to macro- and micro-sized plastics and their impact on aquatic organisms. However, micro-sized plastics degrade subsequently into nano-sizes whereas nano-sized particles may be released directly into nature. Such particles have a different impact on aquatic organisms than larger pieces of plastic due to their small size, high surface curvature, and large surface area. This review describes the possible sources of nano-sized plastic, its distribution and behavior in nature, the impact of nano-sized plastic on the well-being of aquatic organisms, and the difference of impact between nano- and micro-sized particles. We also identify research areas which urgently need more attention and suggest experimental methods to obtain useful data.

  15. Immediate loading with single-piece implant following extraction

    Directory of Open Access Journals (Sweden)

    Hemlata Dwivedi

    2017-01-01

    Full Text Available Although dental implantology had evolved over a number of years, many dental surgeons are unaware of the concept of immediate loading with the use of one-piece implant that began in the early 1960s. The goal of successful prosthodontics rehabilitation is to provide function, esthetics, and comfort to the patient. The aim of this literature is to provide an overview of one-piece implant, with its advantages and disadvantages over conventional two-piece implant. Immediate prosthetic of a one-piece system allows for a better tissue healing and better adhesion of gingival mucosa to form a collar which is healthy and adherent to the implant, avoiding a second surgical procedure, and also includes a very important aspect esthetics. This article describes a case report of immediate loading with single-piece implant following extraction.

  16. Magical Engineering Plastic

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Gwang Ung

    1988-01-15

    This book introduces engineering plastic about advantage of engineering plastic, plastic material from processing method, plastic shock, plastic until now, background of making of engineering plastic, wonderful engineering plastic science such as a high molecule and molecule, classification of high molecule, difference between metal and high molecule, heat and high molecule materials, and property of surface, engineering plastic of dream like from linseed oil to aramid, small dictionary of engineering plastic.

  17. Magical Engineering Plastic

    International Nuclear Information System (INIS)

    Kim, Gwang Ung

    1988-01-01

    This book introduces engineering plastic about advantage of engineering plastic, plastic material from processing method, plastic shock, plastic until now, background of making of engineering plastic, wonderful engineering plastic science such as a high molecule and molecule, classification of high molecule, difference between metal and high molecule, heat and high molecule materials, and property of surface, engineering plastic of dream like from linseed oil to aramid, small dictionary of engineering plastic.

  18. Mixed plastics recycling technology

    CERN Document Server

    Hegberg, Bruce

    1995-01-01

    Presents an overview of mixed plastics recycling technology. In addition, it characterizes mixed plastics wastes and describes collection methods, costs, and markets for reprocessed plastics products.

  19. Pervasive plastic

    Science.gov (United States)

    2018-05-01

    Human manipulation of hydrocarbons — as fuel and raw materials for modern society — has changed our world and the indelible imprint we will leave in the rock record. Plastics alone have permeated our lives and every corner of our planet.

  20. Plastic fish

    CERN Multimedia

    Antonella Del Rosso

    2015-01-01

    In terms of weight, the plastic pollution in the world’s oceans is estimated to be around 300,000 tonnes. This plastic comes from both land-based and ocean-based sources. A lecture at CERN by chemist Wolfgang Trettnak addressed this issue and highlighted the role of art in raising people’s awareness.   Artwork by Wolfgang Trettnak. Packaging materials, consumer goods (shoes, kids’ toys, etc.), leftovers from fishing and aquaculture activities… our oceans and beaches are full of plastic litter. Most of the debris from beaches is plastic bottles. “PET bottles have high durability and stability,” explains Wolfgang Trettnak, a chemist by education and artist from Austria, who gave a lecture on this topic organised by the Staff Association at CERN on 26 May. “PET degrades very slowly and the estimated lifetime of a bottle is 450 years.” In addition to the beach litter accumulated from human use, rivers bring several ki...

  1. Plastic deformation

    NARCIS (Netherlands)

    Sitter, de L.U.

    1937-01-01

    § 1. Plastic deformation of solid matter under high confining pressures has been insufficiently studied. Jeffreys 1) devotes a few paragraphs to deformation of solid matter as a preface to his chapter on the isostasy problem. He distinguishes two properties of solid matter with regard to its

  2. Application of SFM and laser scanning technology to the description of mosaics piece by piece

    Directory of Open Access Journals (Sweden)

    O. Ajioka

    2014-06-01

    Full Text Available Mosaic floors of surviving buildings in Ostia have been mainly recorded in photographs. From 2008, Japanese research group carries out a project of 3d measuring of the whole structure of ancient Roman city Ostia using laser scanners, including its landscape, city blocks, streets, buildings, wall paintings and mosaics. The laser scanner allows for a more detailed analysis and a greater potential for recording mosaics. We can record the data of mosaics, which are described piece by piece. However it is hard to acquire enough high dense point cloud and the internal camera of the laser scanner produce low quality images. We introduce a possible technology of 3D recording of mosaics with high-quality colour information; SFM. The use of this technique permits us to create 3D models from images provided from a CCD camera without heavy and large laser scanners. We applied SFM system to different three types of the mosaics laid down on the floors of "the House of the Dioscuroi", "the Insula of the Muse" and "the House of Jove and Ganymede", and created high resolution orthographic images. Then we examined to compare these orthographic images with that are created from the point cloud data. As a result, we confirmed that SFM system has sufficient practical utility for the mosaic research. And we present how much of density of point cloud or ground resolution are required for the documentation of mosaics accurately.

  3. Phenotypic plasticity, costs of phenotypes, and costs of plasticity

    DEFF Research Database (Denmark)

    Callahan, Hilary S; Maughan, Heather; Steiner, Uli

    2008-01-01

    Why are some traits constitutive and others inducible? The term costs often appears in work addressing this issue but may be ambiguously defined. This review distinguishes two conceptually distinct types of costs: phenotypic costs and plasticity costs. Phenotypic costs are assessed from patterns...... of covariation, typically between a focal trait and a separate trait relevant to fitness. Plasticity costs, separable from phenotypic costs, are gauged by comparing the fitness of genotypes with equivalent phenotypes within two environments but differing in plasticity and fitness. Subtleties associated with both...... types of costs are illustrated by a body of work addressing predator-induced plasticity. Such subtleties, and potential interplay between the two types of costs, have also been addressed, often in studies involving genetic model organisms. In some instances, investigators have pinpointed the mechanistic...

  4. A three-dimensional analysis of fracture mechanics test pieces of different geometries part 2 - Constraint and material variations

    Energy Technology Data Exchange (ETDEWEB)

    Tkach, Y., E-mail: Yuri.Tkach@WGIM.com [Department of Civil and Structural Engineering, School of MACE, UMIST/University of Manchester, PO Box 88, Manchester M60 1QD (United Kingdom); Burdekin, F.M., E-mail: mburdekin@aol.com [Department of Civil and Structural Engineering, School of MACE, UMIST/University of Manchester, PO Box 88, Manchester M60 1QD (United Kingdom)

    2012-05-15

    This paper reports the second stage of an extensive series of detailed three-dimensional elastic-plastic finite element analyses on the influence of fracture mechanics test specimen geometry and different material properties on constraint and triaxiality in the near crack tip region. The specimens studied were pre-cracked plain-sided and side-grooved Charpy sized specimens, plain-sided and side-grooved compact tension specimens of thickness B = 25 mm and plain-sided compact tension specimens of thickness B = 100 mm all with the ratio of the crack length to the specimen width a/W = 0.5. Stress-strain curves of materials of different yield strength and strain hardening behaviour spanning the range of practical interest for typical structural steels were implemented into the finite element models. The level of constraint in the specimens modelled has been characterised in terms of both the Q-stress parameter and the ratio of hydrostatic to the equivalent stress components. It has been established that in-plane constraint in the fracture toughness test pieces is significantly affected by the absolute ligament size of the specimen. It has also been shown that the strain hardening behaviour is one of the major material parameters defining constraint level in the fracture toughness specimen. - Highlights: Black-Right-Pointing-Pointer 3D FE analyses on plain and side-grooved Charpy sized and CT specimens of two sizes. Black-Right-Pointing-Pointer Crack tip constraint analysed for Q-stress and hydrostatic/equivalent stress ratio. Black-Right-Pointing-Pointer In-plane constraint is significantly affected by the absolute ligament size. Black-Right-Pointing-Pointer Constraint level is significantly affected by material strain hardening behaviour.

  5. A three-dimensional analysis of fracture mechanics test pieces of different geometries part 2 - Constraint and material variations

    International Nuclear Information System (INIS)

    Tkach, Y.; Burdekin, F.M.

    2012-01-01

    This paper reports the second stage of an extensive series of detailed three-dimensional elastic-plastic finite element analyses on the influence of fracture mechanics test specimen geometry and different material properties on constraint and triaxiality in the near crack tip region. The specimens studied were pre-cracked plain-sided and side-grooved Charpy sized specimens, plain-sided and side-grooved compact tension specimens of thickness B = 25 mm and plain-sided compact tension specimens of thickness B = 100 mm all with the ratio of the crack length to the specimen width a/W = 0.5. Stress–strain curves of materials of different yield strength and strain hardening behaviour spanning the range of practical interest for typical structural steels were implemented into the finite element models. The level of constraint in the specimens modelled has been characterised in terms of both the Q-stress parameter and the ratio of hydrostatic to the equivalent stress components. It has been established that in-plane constraint in the fracture toughness test pieces is significantly affected by the absolute ligament size of the specimen. It has also been shown that the strain hardening behaviour is one of the major material parameters defining constraint level in the fracture toughness specimen. - Highlights: ► 3D FE analyses on plain and side-grooved Charpy sized and CT specimens of two sizes. ► Crack tip constraint analysed for Q-stress and hydrostatic/equivalent stress ratio. ► In-plane constraint is significantly affected by the absolute ligament size. ► Constraint level is significantly affected by material strain hardening behaviour.

  6. RETAINED STONE PIECE IN ANTERIOR CHAMBER

    Directory of Open Access Journals (Sweden)

    ZvornicaninJasmin, Nadarevic-VodencarevicAmra

    2015-04-01

    Full Text Available ABSTRACT We read with interest the article by Surekha et al. regarding the retained stone piece in anterior chamber. Similar to the results of previous studies, the authors found that delayed intraocular foreign body (IOFB management can result in good visual outcome without an apparent increased risk of endophthalmitis or other deleterious side effects. However, the authors failed to explain the exact reason for the diminution of vision in patients left eye. It is unclear what the uncorrected visual acuity was and what kind of correction was used, more precisely type and amount of cylinder, given the presence of the corneal opacity. Since the size of the IOFB is approximately 4x4x1mm, significant irido-corneal angle changes resulting in intraocular pressure raise and optic nerve head damage can be expected. Traumatic glaucoma following open globe injury can occur in 2.7 to 19% of cases, with several risk factors associated with glaucoma development (advanced age, poor visual acuity at presentation,perforating rather than penetrating ocular injury,lens injury, presence of vitreous hemorrhage and presence of an IOFB. Earlier reportsof latetraumaticoptic neuropathy onset, even after several years, indicate that this possibility cannot be completely ruled out too. Therefore, repeated intraocular pressure measurements, gonioscopy, pupillary reaction assessment, together with through posterior segment examination including visual field and optical coherence tomography examinations can be useful in determining the possible optic nerve damage as one of the possible reasons for visual acuity reduction. The authors did not suggest any operative treatment at this time. However, it should bear in mind that the inert anterior chamber IOFB could be a risk factor for non-infectious endophthalmitis development even after many years. Also, long term retained anterior chamber foreign body leads to permanent endothelial cell loss and can even result in a corneal

  7. plastic waste recycling

    African Journals Online (AJOL)

    Dr Ahmed

    incinerators is increasing around the world. Discarded plastic products ... Agency (EPA) estimated that the amount of plastics throw away is. 50 % greater in the ... The waste plastics were identified using the Society of the Plastic. Industry (SPI) ...

  8. [Suggestions to strengthen quality management of herbal decoction pieces--based on production chain of herbal decoction pieces].

    Science.gov (United States)

    Liu, Yan; Nie, Qing; Chen, Jing

    2015-08-01

    With the development of society and the improvement of people's living standards, the effect of Chinese medicine in treatment and health care is more and more prominent. The herbal decoction pieces are the important part of Chinese medicine,it can be applied directly to clinical treatment and it's also the raw material of Chinese patent medicine. Therefore, the quality of herbal decoction pieces is quite important. The parts of the production of herbal decoction pieces are numerous, and there are possibilities of adverse effects on the quality of the herbal decoction pieces in every part. In this paper, we based on the production chain of herbal decoction pieces, analyzed the main problem that affect the quality of herbal decoction pieces in the part of selection of Chinese herbal medicines, planting, purchasing, processing, packaging, storage and transport, such as the poor quality of seed and seedlings of plant-based Chinese medicines, some plants left their place of origin and have been introduced in the place that is not suitable for this kind of plant, the insufficient growth time and the excessive harmful substances. The purchasers and the accepters lack of professional knowledge and professional ethics. The mechanism of processing is not clear, the standards can not be uniformed, and lack of qualified person in processing, etc. So we suggest: intensify the basic research of key scientific issues. Improve the quality of persons who work in herbal decoction pieces; Establish an "integration" mode of operation in herbal decoction pieces enterprise; Breeding high quality plant resources, establish the large-scale planting basement; Make the packing of herbal decoction pieces standard; Establish the modernization traditional Chinese medicine logistics enterprise.

  9. 40 Years of Processing Pieces of Space

    Science.gov (United States)

    Satterwhite, C. E.; Funk, R. C.; Righter, K.; Harrington, R. H.

    2016-01-01

    representative sample, either a 1-3 gram chip or thin section is sent to the Smithsonian Institution for classification. After Antarctic meteorites have been classified and approved by the Nomenclature Committee of the Meteoritical Society, they are announced in the Antarctic Meteorite Newsletter, which is published twice per year (fall and spring) so that scientists may review which meteorites are available to study. Requests for Antarctic Meteorite samples are welcomed from research scientists, regardless of their current state of funding for meteorite studies. Since its inception over 3,300 requests have been made for pieces of these meteorites and over 400 investigators worldwide are active in the study of meteorites.. Research on these samples has been published in more than1500 peer reviewed articles; a listing of papers for any meteorite sample can be generated by accessing http://curator.jsc.nasa.gov/antmet/referencesearch.cfm. Antarctic meteorite samples requested by scientists are prepared several different ways. Most samples are prepared as chips, either using a rock splitter or using a chisel and chipping bowl. In special situations, a researcher may request a meteorite slab in which case the samples are cut using a diamond-bladed bandsaw inside of a dry nitrogen glove box. The meteorites are always cut in a 100 percent liquid-free environment. Additionally, thin/thick sections of Antarctic meteorites are also prepared at JSC. The meteorite thin section lab at JSC can prepare standard 30-micron thin sections, thick sections of variable thickness (100 to 200 microns), or demountable sections using superglue, all section are prepared without using water. Although many of the techniques used back in the '70's are still used today, advances in computers, software, databases, available tools and instrumentation have helped to streamline and shorten the duration of the classification process. In conjunction with present day missions to asteroids and other planets

  10. Image analysis of multiple moving wood pieces in real time

    Science.gov (United States)

    Wang, Weixing

    2006-02-01

    This paper presents algorithms for image processing and image analysis of wood piece materials. The algorithms were designed for auto-detection of wood piece materials on a moving conveyor belt or a truck. When wood objects on moving, the hard task is to trace the contours of the objects in n optimal way. To make the algorithms work efficiently in the plant, a flexible online system was designed and developed, which mainly consists of image acquisition, image processing, object delineation and analysis. A number of newly-developed algorithms can delineate wood objects with high accuracy and high speed, and in the wood piece analysis part, each wood piece can be characterized by a number of visual parameters which can also be used for constructing experimental models directly in the system.

  11. One-Piece Faraday Generator: A Paradoxical Experiment from 1851

    Science.gov (United States)

    Crooks, M. J.; And Others

    1978-01-01

    Describes an experiment based on Faraday's one-piece generator, where the rotating disk is replaced by a cylindrical permanent magnet. Explains the apparent paradox that an observer in an inertial frame could measure his absolute velocity. (GA)

  12. Prediction of hardness in pieces of quenched and tempered steel

    International Nuclear Information System (INIS)

    Yanzon, Rodolfo Carlos; Rodriguez, Augusto; Sanchez, Arlington Ricardo

    2006-01-01

    This presentation describes the first stage of a work plan to obtain a simple software, for predicting properties at certain points of a quenched and tempered piece. In this first stage, this prediction is limited to cylindrical pieces made with steels whose chemical composition is within a certain range. The methodology basically consists of obtaining , from experimental data, a mathematical tool able to predict the hardness value, for Jominy test piece ends made with this type of steel. This meant beginning with the analysis of the usual forms of theoretical calculation of Jominy curves of quenched samples, which resulted in a proposal to modify the Just equation. Two different mathematical methods were then developed, that could predict hardness values in tempered Jominy test pieces. One, based on the determination of polynomic equations, that reproduces the loss of hardness at points along the test piece, base on the quenching value and as a function of the tempering temperature. The other one, which uses the lineal multidimensional interpolation method, because of its ease of application, has been selected as the mathematical tool to use in the software under development. At this stage of the work, the relationship between the points on the piece and those on the Jominy test pieces is carried out by the Lamont method and the representative variable of the temperature/time combination for the tempering process itself, is obtained with software based on the Hollomon and Jaffe expression. Data is needed to define: a) chemical composition and grain size of the steel used, b) diameter of the piece, c) 'H G ' severity of the quenching medium d) temperature and time of the tempering. The work's second stage continued with the addition of hardness values measured in Jominy test pieces made with other steels. The chemical composition and grain size data of each steel introduced are converted by the software into one more variable, using the concept of ideal critical

  13. Plastic ingestion by fulmars and shearwaters at Sable Island, Nova Scotia, Canada.

    Science.gov (United States)

    Bond, Alexander L; Provencher, Jennifer F; Daoust, Pierre-Yves; Lucas, Zoe N

    2014-10-15

    Plastic pollution is widespread in the marine environment, and plastic ingestion by seabirds is now widely reported for dozens of species. Beached Northern Fulmars, Great Shearwaters, Sooty Shearwaters and Cory's Shearwaters are found on Sable Island, Nova Scotia, Canada regularly, and they can be used to assess plastic pollution. All species except Cory's Shearwaters contained plastic debris in their gastrointestinal tracts. Northern Fulmars, Sooty Shearwaters and Great Shearwaters all showed high prevalence of plastic ingestion (>72%), with Northern Fulmars having the highest number and mass of plastics among the species examined. There was no difference in plastic ingestion between sexes or age classes. In all species user plastics made up the majority of the pieces found, with industrial pellets representing only a small proportion in the samples. Sable Island could be an important monitoring site for plastic pollution in Atlantic Canada. Copyright © 2014 Elsevier Ltd. All rights reserved.

  14. Improved airline-type supplied-air plastic suit

    International Nuclear Information System (INIS)

    Jolley, L. Jr.; Zippler, D.B.; Cofer, C.H.; Harper, J.A.

    1978-06-01

    Two piece supplied-air plastic suits are used extensively at the Savannah River Plant for personnel protection against inhalation of airborne plutonium and tritium. Worker comfort and noise level problems gave impetus to development of an improved suit and aid distribution system. The resulting plastic suit and development work are discussed. The plastic suit unit cost is less than $20, the hearing zone noise level is less than 75 dBA, protection factors exceed 10,000, and user comfort is approved. This suit is expected to meet performance requirements for unrestricted use

  15. Threat of plastic pollution to seabirds is global, pervasive, and increasing

    OpenAIRE

    Wilcox, C; Van Sebille, E; Hardesty, BD

    2015-01-01

    Plastic pollution in the ocean is a rapidly emerging global environmental concern, with high concentrations (up to 580,000 pieces per km2) and a global distribution, driven by exponentially increasing production. Seabirds are particularly vulnerable to this type of pollution and are widely observed to ingest floating plastic. We used a mixture of literature surveys, oceanographic modeling, and ecological models to predict the risk of plastic ingestion to 186 seabird species globally. Impacts ...

  16. Testing typicality in multiverse cosmology

    Science.gov (United States)

    Azhar, Feraz

    2015-05-01

    In extracting predictions from theories that describe a multiverse, we face the difficulty that we must assess probability distributions over possible observations prescribed not just by an underlying theory, but by a theory together with a conditionalization scheme that allows for (anthropic) selection effects. This means we usually need to compare distributions that are consistent with a broad range of possible observations with actual experimental data. One controversial means of making this comparison is by invoking the "principle of mediocrity": that is, the principle that we are typical of the reference class implicit in the conjunction of the theory and the conditionalization scheme. In this paper, we quantitatively assess the principle of mediocrity in a range of cosmological settings, employing "xerographic distributions" to impose a variety of assumptions regarding typicality. We find that for a fixed theory, the assumption that we are typical gives rise to higher likelihoods for our observations. If, however, one allows both the underlying theory and the assumption of typicality to vary, then the assumption of typicality does not always provide the highest likelihoods. Interpreted from a Bayesian perspective, these results support the claim that when one has the freedom to consider different combinations of theories and xerographic distributions (or different "frameworks"), one should favor the framework that has the highest posterior probability; and then from this framework one can infer, in particular, how typical we are. In this way, the invocation of the principle of mediocrity is more questionable than has been recently claimed.

  17. Plastic scintillator

    International Nuclear Information System (INIS)

    Andreeshchev, E.A.; Kilin, S.F.; Kavyrzina, K.A.

    1978-01-01

    A plastic scintillator for ionizing radiation detectors with high time resolution is suggested. To decrease the scintillation pulse width and to maintain a high light yield, the 4 1 , 4 5 -dibromo-2 1 , 2 5 , 5 1 , 5 5 -tetramethyl-n-quinquiphenyl (Br 2 Me 4 Ph) in combination with n-terphenyl (Ph 3 ) or 2, 5-diphenyloxadiazol-1, 3, 4 (PPD) is used as a luminescent addition. Taking into consideration the results of a special study, it is shown, that the following ratio of ingradients is the optimum one: 3-4 mass% Ph 3 or 4-7 mas% PPD + 2-5 mass% Br 2 Me 4 Ph + + polymeric base. The suggested scintillator on the basis of polystyrene has the light yield of 0.23-0.26 arbitrary units and the scintillation pulse duration at half-height is 0.74-0.84 ns

  18. The smaller the pieces the healthier their consumption

    DEFF Research Database (Denmark)

    Hansen, Pelle Guldborg; Skov, Katrine Lund; Schmidt, Karsten

    the snack breaks. The hypothesis was that consumers could be nudged to healthier food choices by improving accessibility to sliced apples and make a “healthier” cake portion (small) the default. The sample consisted of 391 people attending a congress in Copenhagen, Denmark. People were divided in two groups...... for snacking during breaks, and were informed that this was for logistic reasons. Two snack tables were set up, one with normal sized pieces of cake (usual sizes provided by the caterer) as well as whole apples (control N=189), and a table with halved pieces of cake as well as apples served in quarter pieces....... This pilot study supports the hypothesis that the presentation of snacks plays an important role in the consumption of fruit and cake among Danish adults. Further, it suggests that such approach could become a supportive tool set for achieving PHN objectives....

  19. Prediction of work piece geometry in electrochemical cavity sinking

    Energy Technology Data Exchange (ETDEWEB)

    Riggs, J B; Muller, R H; Tobias, C W

    1981-01-01

    A computer-implemented model for predicting ECM work piece geometry has been developed and experimentally verified with a commercial ECM machine for cavity sinking in copper and 302-stainless steel with 2N KNO/sub 3/ electrolyte. Constant tool piece feed rates of 7-10 x 10/sup -4/ cm/s, and applied voltages of 11-25 V were used. The model predicts the dependence of work piece geometry on operating conditions and on the electrochemical and physical properties of the metal-electrolyte pair. Comparison of eight equilibrium and six unsteady state experimental cavity profiles in copper showed satisfactory agreement with predictions, as did five equilibrium profiles for cavity sinking in 302-stainless steel.

  20. Feminist Erotica and Agency @ The Love Piece Club

    OpenAIRE

    DALES, Laura

    2008-01-01

    The Love Piece Club is a shop devoted to sex goods for women, located in Tokyo and online at www.lovepiececlub.com. As well as online shopping, the website offers regular columns, articles and photo-essays on subjects related to sexuality and women's lives. The site and shop are managed by Kitahara Minori, a writer, businesswoman and advocate for feminist erotica. This paper explores the Love Piece Club as a discursive site – its potential meanings and its significance as a feminist work in p...

  1. Toxicological Threats of Plastic

    Science.gov (United States)

    Plastics pose both physical (e.g., entanglement, gastrointestinal blockage, reef destruction) and chemical threats (e.g., bioaccumulation of the chemical ingredients of plastic or toxic chemicals sorbed to plastics) to wildlife and the marine ecosystem.

  2. Management of sulcus-fixated single-piece intraocular lens-induced pigmentary glaucoma with 3-piece IOL exchange.

    Science.gov (United States)

    Rabie, Hossein Mohammad; Esfandiari, Hamed; Rikhtegar, Mohammad Hassan; Hekmat, Vahid

    2018-02-01

    To describe our experience with exchanging sulcus-fixated single-piece intraocular lens (IOL) with 3-piece IOLs for management of pigmentary glaucoma. In this retrospective study, records of patients who underwent sulcus-fixated single-piece IOL exchanged with 3-piece IOLs were retrieved, and demographic and baseline data of patients, type of IOL, pre- and post-IOL exchange BCVA, IOP, number of anti-glaucoma medications, and optic nerve head examination were documented. Baseline and final examinations were analyzed and compared. Mean age of the patients was 59 ± 10 years, and 5 (41.6%) were female. Mean interval between primary cataract extraction operation and IOL exchange was 17 ± 5 months. Nine patients received in sulcus implantation of Alcon SA60AT, and three patients had SN60WF model at the end of primary surgery. BCVA changed insignificantly from 0.06 ± 0.06 logMAR to 0.06 ± 0.06 after IOL exchange. (P = 0.22) IOP was controlled in 8 cases (66.6%), but four cases (33.3%) needed glaucoma surgery to further control glaucoma condition. IOP decreased significantly from preoperative 17 ± 3 to 14 ± 1 mmHg postoperatively. Patients with advanced age and higher baseline IOP were more likely to undergo glaucoma surgery after IOL exchange. (P = 0.07 and 0.00, respectively). single-piece IOL exchange with 3-piece IOL dramatically decreases pigment release and reduces IOP. Those with advanced age and higher IOP are less likely to respond to IOL exchange and may need glaucoma surgery to control high intraocular pressure.

  3. Torque Removal Evaluation of Screw in One-Piece and Two-Piece Abutments Tightened with a Handheld screwdriver

    Directory of Open Access Journals (Sweden)

    Jalil Ghanbarzadeh

    2013-12-01

    Full Text Available Introduction: Some clinicians use a handheld screw driver instead of a torque wrench to definitively tighten abutment screws. The aim of this study was to compare the removal torque of one-piece and two-piece abutments tightened with a handheld driver and a torque control ratchet. Methods: 40 ITI implants were placed in acrylic blocks and divided into 4 groups. In groups one and two, 10 ITI one-piece abutments (Solid® and in groups three and four, 10 ITI two-piece abutments (Synocta® were placed on the implants. In groups one and three abutments were tightened by 5 experienced males and 5 experienced females using a handheld driver. In groups two and four abutments were tightened using a torque wrench with torque values of 10, 20 and 35 N.cm. Insertion torque and removal torque values of the abutments were measured with a digital torque meter. Results: The insertion torque values (ITVs of males in both abutments were significantly higher than those of females. ITVs in both Solid® and Synocta® abutments tightened with a handheld screwdriver were similar to the torque of 20 N.cm in the torque wrench. Removal torque values (RTVs of solid® abutments were higher than those of synocta® abutments. Conclusion: The one- piece abutments (solid® showed higher RTVs than the two-piece abutments (synocta®. Hand driver does not produce sufficient preload force for the final tightening of the abutment

  4. A piece of paper falling faster than free fall

    International Nuclear Information System (INIS)

    Vera, F; Rivera, R

    2011-01-01

    We report a simple experiment that clearly demonstrates a common error in the explanation of the classic experiment where a small piece of paper is put over a book and the system is let fall. This classic demonstration is used in introductory physics courses to show that after eliminating the friction force with the air, the piece of paper falls with acceleration g. To test if the paper falls behind the book in a nearly free fall motion or if it is dragged by the book, we designed a version of this experiment that includes a ball and a piece of paper over a book that is forced to fall using elastic cords. We recorded a video of our experiment using a high-speed video camera at 300 frames per second that shows that the book and the paper fall faster than the ball, which falls well behind the book with an acceleration approximately equal to g. Our experiment shows that the piece of paper is dragged behind the book and therefore the paper and book demonstration should not be used to show that all objects fall with acceleration g independently of their mass.

  5. Swiveling Lathe Jaw Concept for Holding Irregular Pieces

    Science.gov (United States)

    David, J.

    1966-01-01

    Clamp holds irregularly shaped pieces in lathe chuck without damage and eliminates excessive time in selecting optimum mounting. Interchangeable jaws ride in standard jaw slots but swivel so that the jaw face bears evenly against the workpiece regardless of contour. The jaws can be used on both engine and turret lathes.

  6. A piece of paper falling faster than free fall

    Energy Technology Data Exchange (ETDEWEB)

    Vera, F; Rivera, R, E-mail: fvera@ucv.cl [Instituto de Fisica, Pontificia Universidad Catolica de ValparaIso, Av. Universidad 330, Curauma, ValparaIso (Chile)

    2011-09-15

    We report a simple experiment that clearly demonstrates a common error in the explanation of the classic experiment where a small piece of paper is put over a book and the system is let fall. This classic demonstration is used in introductory physics courses to show that after eliminating the friction force with the air, the piece of paper falls with acceleration g. To test if the paper falls behind the book in a nearly free fall motion or if it is dragged by the book, we designed a version of this experiment that includes a ball and a piece of paper over a book that is forced to fall using elastic cords. We recorded a video of our experiment using a high-speed video camera at 300 frames per second that shows that the book and the paper fall faster than the ball, which falls well behind the book with an acceleration approximately equal to g. Our experiment shows that the piece of paper is dragged behind the book and therefore the paper and book demonstration should not be used to show that all objects fall with acceleration g independently of their mass.

  7. The Key Pieces of the Career Survival and Success Puzzle.

    Science.gov (United States)

    Simonetti, Jack L.

    1999-01-01

    Analysis of career-success factors identified by 5,000 managers yielded 10 key pieces: excellent performance record, communication skills, interpersonal skills, personality, skill currency, significant work experiences, power, ability to withstand pressure, ability to make difficult decisions, and having a mentor. (SK)

  8. Development of debris-resistant bottom end piece

    International Nuclear Information System (INIS)

    Sohn, Dong Seong; Lee, Jae Kyung; Hwang, Dae Hyun; Yim, Jung Sik; Song, Kee Nam; Oh, Dong Seok; Im, Hyun Tae

    1993-01-01

    Debris-related fuel failures has been identified to be one of the major causes of fuel failures recently occured in nuclear power plants. In order to reduce the possibility of debris-related fuel failures, it is necessary to prevent the debris from reaching to fuel rods. In this regard, it is important to develop Debris-Resistant Bottom End Piece. (Author)

  9. Recycling of Plastic

    DEFF Research Database (Denmark)

    Christensen, Thomas Højlund; Fruergaard, Thilde

    2011-01-01

    Plastic is produced from fossil oil. Plastic is used for many different products. Some plastic products like, for example, wrapping foil, bags and disposable containers for food and beverage have very short lifetimes and thus constitute a major fraction of most waste. Other plastic products like...

  10. Large area spark chamber and support, and method of recording and analyzing the information on a radioactive work piece

    International Nuclear Information System (INIS)

    Britten, R.J.; Davidson, E.H.

    1985-01-01

    Novel large area spark chamber having a support for carrying a generally planar, radioactive work piece. The spark chamber has a thin window which is either a rigid plastic sheet carrying a thin layer of an electrically conductive material on the surface thereof, or a thin planar piece or film of electrically conductive metal. There is positioned in superposed relationship to the thin window, a layer of semi-conducting glass in spaced-apart relationship from the thin window by a resilient insulating seal to form an enclosed gas retaining chamber. An electrically conducting surface is adhered to the upper surface of the layer of semi-conducting glass. An electrically conductive path is provided between the thin layer of electrically conductive material on the thin window and the electrically conducting surface on said semi-conducting glass. The electrically conductive path includes a high voltage supply and TDCs and ADCs. There are also means for detecting the location of sites of impingement of radiation on the electrically conducting surface of the semi-conducting glass, and means for recording and analyzing the information present on the work piece

  11. PTL: A Propositional Typicality Logic

    CSIR Research Space (South Africa)

    Booth, R

    2012-09-01

    Full Text Available consequence relations first studied by Lehmann and col- leagues in the 90?s play a central role in nonmonotonic reasoning [13, 14]. This has been the case due to at least three main reasons. Firstly, they are based on semantic constructions that are elegant...) j ; 6j : ^ j PTL: A Propositional Typicality Logic 3 The semantics of (propositional) rational consequence is in terms of ranked models. These are partially ordered structures in which the ordering is modular. Definition 1. Given a set S...

  12. Presence of plastic particles in waterbirds faeces collected in Spanish lakes.

    Science.gov (United States)

    Gil-Delgado, J A; Guijarro, D; Gosálvez, R U; López-Iborra, G M; Ponz, A; Velasco, A

    2017-01-01

    Plastic intake by marine vertebrates has been widely reported, but information about its presence in continental waterfowl is scarce. Here we analyzed faeces of waterbirds species (European coot, Fulica atra, mallard, Anas platyrhynchos and shelduck, Tadorna tadorna) for plastic debris in five wetlands in Central Spain. We collected 89 faeces of shelduck distributed in four lakes, 43.8% of them presented plastic remnants. Sixty percent of 10 faeces of European coot and 45% of 40 faeces of mallard contained plastic debris. Plastic debris found was of two types, threads and fragments, and were identified as remnants of plastic objects used in agricultural fields surrounding the lakes. Differences in prevalence of plastic in faeces, number of plastic pieces per excrement and size of the plastic pieces were not statistically significant between waterfowl species. Thus, our results suggest that plastic may also be frequently ingested by waterfowl in continental waters, at least in our study area. Future studies should address this potential problem for waterbird conservation in other wetlands to evaluate the real impact of this pollutant on waterbirds living in inland water. Copyright © 2016 Elsevier Ltd. All rights reserved.

  13. High prevalence of parental delivery of plastic debris in Cory’s shearwaters (Calonectris diomedea)

    OpenAIRE

    Rodríguez, Airam; Rodríguez, Beneharo; Carrasco, María Nazaret

    2012-01-01

    Plastic ingestion by adult Procellariiformes has been widely recorded, but few studies have evaluated intergenerational transfer. We assessed the prevalence of plastic particles, as well as their basic character- istics, in the gut content of dead Cory’s shearwater fledglings stranded by light pollution on Canary Islands. Eighty-three percent of birds were affected, containing on average 8.0 plastic pieces per bird. The average plastic weight per bird was low (2.97 ± 3.97 mg) compared with ...

  14. Different Digitalization Techniques for 3D Printing of Anatomical Pieces.

    Science.gov (United States)

    Ugidos Lozano, M T; Blaya Haro, F; Ruggiero, Alessandro; Manzoor, S; Nuere Menendez-Pidal, S; Juanes Méndez, J A

    2018-01-25

    The use of different technological devices that allow the creation of three-dimensional models is in constant evolution, allowing a greater application of these technologies in different fields of health sciences and medical training. The equipment for digitalization is becoming increasingly sophisticated allowing obtaining three-dimensional which are more defined and similar to real image and original object. In this work, different modalities of designing 3D anatomical models of bone pieces are presented, for use by students of different disciplines in Health Sciences. To do this we digitalized bone pieces, with different models of scanners, producing images that can be transformed for 3D printing, with a Colido X 3045 printer by digital treatment with different software.

  15. Inspection of complex geometry pieces with an intelligent contact transducer

    International Nuclear Information System (INIS)

    Chatillon, S.; Roy, O.; Mahaut, St.

    2000-01-01

    A new multi-element contact transducer has been developed to improve the inspection of components with complex geometry. The emitting surface is flexible in order to optimize the contact with pieces. An algorithm, based on a simplified geometric model, has been used to determine the delays law which allows to control the focal characteristics of the transmitted field. Acquisition data lead in transmission with an articulated transducer validate the behavior provided by simulation. Thus the optimization of the delays law ensures the transmission of a beam which is homogeneous and controlled during the moving of the transducer. Inspections in echo-pulse mode are implemented on a sample simulating a component controlled on site. Results show that the dynamical adaptation of the delays law to the geometry of the piece leads to very good performances

  16. Information Fields Navigation with Piece-Wise Polynomial Approximation for High-Performance OFDM in WSNs

    Directory of Open Access Journals (Sweden)

    Wei Wei

    2013-01-01

    Full Text Available Since Wireless sensor networks (WSNs are dramatically being arranged in mission-critical applications,it changes into necessary that we consider application requirements in Internet of Things. We try to use WSNs to assist information query and navigation within a practical parking spaces environment. Integrated with high-performance OFDM by piece-wise polynomial approximation, we present a new method that is based on a diffusion equation and a position equation to accomplish the navigation process conveniently and efficiently. From the point of view of theoretical analysis, our jobs hold the lower constraint condition and several inappropriate navigation can be amended. Information diffusion and potential field are introduced to reach the goal of accurate navigation and gradient descent method is applied in the algorithm. Formula derivations and simulations manifest that the method facilitates the solution of typical sensor network configuration information navigation. Concurrently, we also treat channel estimation and ICI mitigation for very high mobility OFDM systems, and the communication is between a BS and mobile target at a terrible scenario. The scheme proposed here combines the piece-wise polynomial expansion to approximate timevariations of multipath channels. Two near symbols are applied to estimate the first-and second-order parameters. So as to improve the estimation accuracy and mitigate the ICI caused by pilot-aided estimation, the multipath channel parameters were reestimated in timedomain employing the decided OFDM symbol. Simulation results show that this method would improve system performance in a complex environment.

  17. One Piece Orbitozygomatic Approach Based on the Sphenoid Ridge Keyhole

    DEFF Research Database (Denmark)

    Spiriev, Toma; Poulsgaard, Lars; Fugleholm, Kåre

    2016-01-01

    The one-piece orbitozygomatic (OZ) approach is traditionally based on the McCarty keyhole. Here, we present the use of the sphenoid ridge keyhole and its possible advantages as a keyhole for the one-piece OZ approach. Using transillumination technique the osteology of the sphenoid ridge...... was examined on 20 anatomical dry skull specimens. The results were applied to one-piece OZ approaches performed on freshly frozen cadaver heads. We defined the center of the sphenoid ridge keyhole as a superficial projection on the lateral skull surface of the most anterior and thickest part of the sphenoid...... ridge. It was located 22 mm (standard deviation [SD], 0.22 mm) from the superior temporal line; 10.7 mm (SD, 0.08 mm) posterior and 7.1 mm (SD, 0.22 mm) inferior to the frontozygomatic suture. The sphenoid ridge burr hole provides exposure of frontal, temporal dura as well as periorbita, which...

  18. Alveolar Bone Resorption Evaluation Around Single-piece Designed Bicortical Implants, Using Immediate Loading Protocol, Based on Orthopantomographs

    Directory of Open Access Journals (Sweden)

    Száva Dániel-Tamás

    2017-12-01

    Full Text Available Background: Inserting dental implants in severely atrophied jawbones is a great challenge for the dental practitioner. There are an increasing number of patients who choose dental implantanchored prosthetic restorations despite compromised bone quality and quantity. There have been numerous attempts in adapting implant design for the atrophic crestal bone. One-piece, needle-type basal implant design is a typical design for these cases. These implants are inserted in the remaining compact bone located in the basal aspect of the jawbones. If high primary stability is achieved, these implants are used for immediate loading protocol. From many points of view, this technique is based on contradictory principles compared to classic implant surgery and loading protocols. The aim of this study was to investigate the long-term success of basal one-piece short-diameter dental implants used for immediate loading protocol.

  19. Y-piece temperature and humidification during mechanical ventilation.

    Science.gov (United States)

    Solomita, Mario; Daroowalla, Feroza; Leblanc, Deniese S; Smaldone, Gerald C

    2009-04-01

    Practitioners often presume there is adequate humidification in the ventilator circuit if the Y-piece is at a specified temperature, but control of Y-piece temperature may be inadequate to ensure adequate humidification. In an in vitro bench model we measured water-vapor delivery with several heated humidification setups and a wide range of minute volume (V (E)) values. The setup included a condenser, hygrometry, and thermometer. First, we calibrated the system with a point-source humidifier and water pump. Then we tested the water-vapor delivery during non-heated-wire humidification and during heated-wire humidification with a temperature gradient of +3 degrees C, 0 degrees C, and -3 degrees C between the humidifier and the Y-piece. We compared the results to 2 recommended humidification values: 100% saturated (absolute humidity 44 mg H(2)O/L) gas at 37 degrees C (saturated/37 degrees C); and 75% saturated (absolute humidity 33 mg H(2)O/L), which is the humidity recommended by the International Organization for Standardization (the ISO standard). In all the experiments the setup was set to provide 35 degrees C at the Y-piece. Our method for measuring water-vapor delivery closely approximated the amount delivered by a calibrated pump, but slightly underestimated the water-vapor delivery in all the experiments and the whole V (E) range. At all V (E) values, water-vapor delivery during non-heated-wire humidification matched or exceeded saturated/37 degrees C and was significantly greater than that during heated-wire humidification. During heated-wire humidification, water-vapor delivery varied with the temperature gradient and did not reach saturated/37 degrees C at V (E) > 6 L/min. Water-vapor delivery with the negative temperature gradient was below the ISO standard. Maintaining temperature at one point in the inspiratory circuit (eg, Y-piece), does not ensure adequate water-vapor delivery. Other factors (humidification system, V (E), gradient setting) are critical

  20. Structural Optimization of an Offshore Wind Turbines Transition Pieces for Bucket Foundations

    DEFF Research Database (Denmark)

    Nezhentseva, Anastasia; Andersen, Lars Vabbersgaard; Ibsen, Lars Bo

    Traditionally, offshore constructions are made of steel. The focus of this paper is optimization of a transition piece (TP) connecting the offshore wind turbine column with a suction bucket foundation. Suction caissons, typically used for shallow water depths, have been proved to be adequate...... in residual soil conditions for depths up to approximately 40 m. The existing design practice is limited to the use of steel-flange-reinforced shear panels. Desirable outcome is proposal of an alternative material which does not require extensive welding work. Compact reinforced composite (CRC) is suggested...... curved segments have been introduced between the conical part and the tubular parts of the structure. While the minimum amount of steel and concrete was required for the composite CRC–steel shell model, the pure CRC model appeared to be the least sensitive to geometrical imperfections, corresponding...

  1. Education on the Business of Plastic Surgery During Training: A Survey of Plastic Surgery Residents.

    Science.gov (United States)

    Ovadia, Steven A; Gishen, Kriya; Desai, Urmen; Garcia, Alejandro M; Thaller, Seth R

    2018-06-01

    Entrepreneurial skills are important for physicians, especially plastic surgeons. Nevertheless, these skills are not typically emphasized during residency training. Evaluate the extent of business training at plastic surgery residency programs as well as means of enhancing business training. A 6-question online survey was sent to plastic surgery program directors for distribution to plastic surgery residents. Responses from residents at the PGY2 level and above were included for analysis. Tables were prepared to present survey results. Hundred and sixty-six residents including 147 PGY2 and above residents responded to our survey. Only 43.5% reported inclusion of business training in their plastic surgery residency. A majority of residents reported they do not expect on graduation to be prepared for the business aspects of plastic surgery. Additionally, a majority of residents feel establishment of a formal lecture series on the business of plastic surgery would be beneficial. Results from our survey indicate limited training at plastic surgery programs in necessary business skills. Plastic surgery residency programs should consider incorporating or enhancing elements of business training in their curriculum. This journal requires that authors assign a level of evidence to each article. For a full description of these Evidence-Based Medicine ratings, please refer to the Table of Contents or the online Instructions to Authors www.springer.com/00266 .

  2. Extraction of Organochlorine Pesticides from Plastic Pellets and Plastic Type Analysis.

    Science.gov (United States)

    Pflieger, Marilyne; Makorič, Petra; Kovač Viršek, Manca; Koren, Špela

    2017-07-01

    Plastic resin pellets, categorized as microplastics (≤5 mm in diameter), are small granules that can be unintentionally released to the environment during manufacturing and transport. Because of their environmental persistence, they are widely distributed in the oceans and on beaches all over the world. They can act as a vector of potentially toxic organic compounds (e.g., polychlorinated biphenyls) and might consequently negatively affect marine organisms. Their possible impacts along the food chain are not yet well understood. In order to assess the hazards associated with the occurrence of plastic pellets in the marine environment, it is necessary to develop methodologies that allow for rapid determination of associated organic contaminant levels. The present protocol describes the different steps required for sampling resin pellets, analyzing adsorbed organochlorine pesticides (OCPs) and identifying the plastic type. The focus is on the extraction of OCPs from plastic pellets by means of a pressurized fluid extractor (PFE) and on the polymer chemical analysis applying Fourier Transform-InfraRed (FT-IR) spectroscopy. The developed methodology focuses on 11 OCPs and related compounds, including dichlorodiphenyltrichloroethane (DDT) and its two main metabolites, lindane and two production isomers, as well as the two biologically active isomers of technical endosulfan. This protocol constitutes a simple and rapid alternative to existing methodology for evaluating the concentration of organic contaminants adsorbed on plastic pieces.

  3. Wood-plastic combination

    International Nuclear Information System (INIS)

    Schaudy, R.

    1978-02-01

    A review on wood-plastic combinations is given including the production (wood and plastic component, radiation hardening, curing), the obtained properties, present applications and prospects for the future of these materials. (author)

  4. DESIGNERS’ KNOWLEDGE IN PLASTICS

    DEFF Research Database (Denmark)

    Eriksen, Kaare

    2013-01-01

    The Industrial designers’ knowledge in plastics materials and manufacturing principles of polymer products is very important for the innovative strength of the industry, according to a group of Danish plastics manufacturers, design students and practicing industrial designers. These three groups ...

  5. Characteristics of Structural Breakdown in Plastic Concrete and ...

    African Journals Online (AJOL)

    Characteristics of Structural Breakdown in Plastic Concrete and Their Potentials for Quality Control. ... A typical trace has four such significant features which characterise the mix. The significance of these features are analysed in relation to the functional requirements of plastic concrete in practice. Finally, the potentials of ...

  6. NICHD Research Networks Help Piece Together the Puzzle of Polycystic Ovary Syndrome

    Science.gov (United States)

    ... Print NICHD research networks help piece together the puzzle of polycystic ovary syndrome Many people think that ... more like putting together a thousand-piece jigsaw puzzle. Except that you can’t check the cover ...

  7. The Hiroshima neutron dosimetry enigma: Missing puzzle piece No. 6

    International Nuclear Information System (INIS)

    Gold, Raymond

    1999-01-01

    More than a decade has elapsed since the serious nature of the discrepancy between neutron dosimetry experiments (E) and neutron transport calculations (C) for the Hiroshima site was identified. Since that time extensive efforts to resolve this Hiroshima neutron dosimetry enigma have not only failed, but now demonstrate that the magnitude of this discrepancy is much greater than initially estimated. The currently evaluated E/C ratio for thermal neutron fluence at the Hiroshima site increases rapidly with increasing slant range from the epicenter. In the slant range region beyond 1000 m, E/C exceeds unity by one to two orders of magnitude depending on the specific dosimetry data that are utilized. Principal features that characterize the Hiroshima neutron dosimetry enigma are summarized. Puzzle Piece No. 6: In-situ production and Prompt fallout of radionuclides from Little Boy is advanced as a possible contributory phenomenon to this enigma. (The atom bomb detonated over Hiroshima was called Little Boy.) Measurements of 60 Co and 152 Eu specific activity at the Hiroshima site are used to obtain order of magnitude numerical estimates that show this conjecture is plausible. Comparison of different 60 Co measurements at the Hiroshima site reveals that the variation of E/C with slant range depends on the method used to quantify 60 Co specific activity as well as the type of dosimetry samples that are employed. These 60 Co comparisons lend additional qualitative credence to this conjecture. Within the limits of presently available data, these assessments show that Puzzle Piece No. 6 qualitatively satisfies the principal features that characterize the Hiroshima neutron dosimetry enigma. Nevertheless, current lack of data prevent this conjecture from being conclusively confirmed or refuted. Consequently, specific recommendations are advanced to resolve the Hiroshima neutron dosimetry enigma with emphasis on experimental tests that can quantitatively evaluate Puzzle Piece

  8. Multiple sclerosis pathogenesis: missing pieces of an old puzzle.

    Science.gov (United States)

    Rahmanzadeh, Reza; Brück, Wolfgang; Minagar, Alireza; Sahraian, Mohammad Ali

    2018-06-08

    Traditionally, multiple sclerosis (MS) was considered to be a CD4 T cell-mediated CNS autoimmunity, compatible with experimental autoimmune encephalitis model, which can be characterized by focal lesions in the white matter. However, studies of recent decades revealed several missing pieces of MS puzzle and showed that MS pathogenesis is more complex than the traditional view and may include the following: a primary degenerative process (e.g. oligodendroglial pathology), generalized abnormality of normal-appearing brain tissue, pronounced gray matter pathology, involvement of innate immunity, and CD8 T cells and B cells. Here, we review these findings and discuss their implications in MS pathogenesis.

  9. Multiple piece turbine engine airfoil with a structural spar

    Science.gov (United States)

    Vance, Steven J [Orlando, FL

    2011-10-11

    A multiple piece turbine airfoil having an outer shell with an airfoil tip that is attached to a root with an internal structural spar is disclosed. The root may be formed from first and second sections that include an internal cavity configured to receive and secure the one or more components forming the generally elongated airfoil. The internal structural spar may be attached to an airfoil tip and place the generally elongated airfoil in compression. The configuration enables each component to be formed from different materials to reduce the cost of the materials and to optimize the choice of material for each component.

  10. Electrification: Connecting the Pieces in the Broader View

    Energy Technology Data Exchange (ETDEWEB)

    Gearhart, Chris C [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

    2017-11-28

    Presented at the SELECT Annual Meeting on September 26, 2017, this PowerPoint presentation gives an overview of connectivity and automation and how these new technologies will impact society in both known and unknown ways. Electrification challenges and opportunities are also outlined as without electrification, connectivity and automation will just magnify the negative health, climate and economic problems of the current transportation systems. Electrification can provide benefits while mitigating the negative consequences. And with careful connection of all of the pieces from materials up through controls, a sustainable transportation eco-system is attainable.

  11. Eight piece quadrupole magnet, method for aligning quadrupole magent pole tips

    Science.gov (United States)

    Jaski, Mark S.; Liu, Jie; Donnelly, Aric T.; Downey, Joshua S.; Nudell, Jeremy J.; Jain, Animesh

    2018-01-30

    The invention provides an alternative to the standard 2-piece or 4-piece quadrupole. For example, an 8-piece and a 10-piece quadrupole are provided whereby the tips of each pole may be adjustable. Also provided is a method for producing a quadrupole using standard machining techniques but which results in a final tolerance accuracy of the resulting construct which is better than that obtained using standard machining techniques.

  12. Monitoring of WEEE plastics in regards to brominated flame retardants using handheld XRF

    Energy Technology Data Exchange (ETDEWEB)

    Aldrian, Alexia, E-mail: alexia.aldrian@unileoben.ac.at [Chair of Waste Processing Technology and Waste Management, Montanuniversitaet Leoben, Franz-Josef-Straße 18, 8700 Leoben (Austria); Ledersteger, Alfred, E-mail: a.ledersteger@saubermacher.at [Saubermacher Dienstleistungs AG, Hans-Roth-Straße 1, 8073 Feldkirchen bei Graz (Austria); Pomberger, Roland, E-mail: roland.pomberger@unileoben.ac.at [Chair of Waste Processing Technology and Waste Management, Montanuniversitaet Leoben, Franz-Josef-Straße 18, 8700 Leoben (Austria)

    2015-02-15

    Highlights: • Specification of an empirical factor for conversion from bromine to PBB and PBDE. • The handheld XRF device was validated for this particular application. • A very large number of over 4600 pieces of monitor housings was analysed. • The recyclable fraction mounts up to 85% for TV but only 53% of PC waste plastics. • A high percentage of pieces with bromine contents of over 50,000 ppm was obtained. - Abstract: This contribution is focused on the on-site determination of the bromine content in waste electrical and electronic equipment (WEEE), in particular waste plastics from television sets (TV) and personal computer monitors (PC) using a handheld X-ray fluorescence (XRF) device. The described approach allows the examination of samples in regards to the compliance with legal specifications for polybrominated biphenyls (PBBs) and polybrominated diphenyl ethers (PBDEs) directly after disassembling and facilitates the sorting out of plastics with high contents of brominated flame retardants (BFRs). In all, over 3000 pieces of black (TV) and 1600 pieces of grey (PC) plastic waste were analysed with handheld XRF technique for this study. Especially noticeable was the high percentage of pieces with a bromine content of over 50,000 ppm for TV (7%) and PC (39%) waste plastics. The applied method was validated by comparing the data of handheld XRF with results obtained by GC–MS. The results showed the expected and sufficiently accurate correlation between these two methods. It is shown that handheld XRF technique is an effective tool for fast monitoring of large volumes of WEEE plastics in regards to BFRs for on-site measurements.

  13. Modeling plasticity by non-continuous deformation

    Science.gov (United States)

    Ben-Shmuel, Yaron; Altus, Eli

    2017-10-01

    Plasticity and failure theories are still subjects of intense research. Engineering constitutive models on the macroscale which are based on micro characteristics are very much in need. This study is motivated by the observation that continuum assumptions in plasticity in which neighbour material elements are inseparable at all-time are physically impossible, since local detachments, slips and neighbour switching must operate, i.e. non-continuous deformation. Material microstructure is modelled herein by a set of point elements (particles) interacting with their neighbours. Each particle can detach from and/or attach with its neighbours during deformation. Simulations on two- dimensional configurations subjected to uniaxial compression cycle are conducted. Stochastic heterogeneity is controlled by a single "disorder" parameter. It was found that (a) macro response resembles typical elasto-plastic behaviour; (b) plastic energy is proportional to the number of detachments; (c) residual plastic strain is proportional to the number of attachments, and (d) volume is preserved, which is consistent with macro plastic deformation. Rigid body displacements of local groups of elements are also observed. Higher disorder decreases the macro elastic moduli and increases plastic energy. Evolution of anisotropic effects is obtained with no additional parameters.

  14. Plastics disassembly versus bulk recycling: engineering design for end-of-life electronics resource recovery.

    Science.gov (United States)

    Rios, Pedro; Stuart, Julie Ann; Grant, Ed

    2003-12-01

    Annual plastic flows through the business and consumer electronics manufacturing supply chain include nearly 3 billion lb of high-value engineering plastics derived from petroleum. The recovery of resource value from this stream presents critical challenges in areas of materials identification and recycling process design that demand new green engineering technologies applied together with life cycle assessment and ecological supply chain analysis to create viable plastics-to-plastics supply cycles. The sustainable recovery of potentially high-value engineering plastics streams requires that recyclers either avoid mixing plastic parts or purify later by separating smaller plastic pieces created in volume reduction (shredding) steps. Identification and separation constitute significant barriers in the plastics-to-plastics recycling value proposition. In the present work, we develop a model that accepts randomly arriving electronic products to study scenarios by which a recycler might identify and separate high-value engineering plastics as well as metals. Using discrete eventsimulation,we compare current mixed plastics recovery with spectrochemical plastic resin identification and subsequent sorting. Our results show that limited disassembly with whole-part identification can produce substantial yields in separated streams of recovered engineering thermoplastics. We find that disassembly with identification does not constitute a bottleneck, but rather, with relatively few workers, can be configured to pull the process and thus decrease maximum staging space requirements.

  15. Occurrence and effects of plastic additives on marine environments and organisms: A review.

    Science.gov (United States)

    Hermabessiere, Ludovic; Dehaut, Alexandre; Paul-Pont, Ika; Lacroix, Camille; Jezequel, Ronan; Soudant, Philippe; Duflos, Guillaume

    2017-09-01

    Plastics debris, especially microplastics, have been found worldwide in all marine compartments. Much research has been carried out on adsorbed pollutants on plastic pieces and hydrophobic organic compounds (HOC) associated with microplastics. However, only a few studies have focused on plastic additives. These chemicals are incorporated into plastics from which they can leach out as most of them are not chemically bound. As a consequence of plastic accumulation and fragmentation in oceans, plastic additives could represent an increasing ecotoxicological risk for marine organisms. The present work reviewed the main class of plastic additives identified in the literature, their occurrence in the marine environment, as well as their effects on and transfers to marine organisms. This work identified polybrominated diphenyl ethers (PBDE), phthalates, nonylphenols (NP), bisphenol A (BPA) and antioxidants as the most common plastic additives found in marine environments. Moreover, transfer of these plastic additives to marine organisms has been demonstrated both in laboratory and field studies. Upcoming research focusing on the toxicity of microplastics should include these plastic additives as potential hazards for marine organisms, and a greater focus on the transport and fate of plastic additives is now required considering that these chemicals may easily leach out from plastics. Copyright © 2017 Elsevier Ltd. All rights reserved.

  16. Plastic value chains

    DEFF Research Database (Denmark)

    Baxter, John; Wahlstrom, Margareta; Zu Castell-Rüdenhausen, Malin

    2014-01-01

    Optimizing plastic value chains is regarded as an important measure in order to increase recycling of plastics in an efficient way. This can also lead to improved awareness of the hazardous substances contained in plastic waste, and how to avoid that these substances are recycled. As an example......, plastics from WEEE is chosen as a Nordic case study. The project aims to propose a number of improvements for this value chain together with representatives from Nordic stakeholders. Based on the experiences made, a guide for other plastic value chains shall be developed....

  17. Biodegradability of Plastics

    Directory of Open Access Journals (Sweden)

    Yutaka Tokiwa

    2009-08-01

    Full Text Available Plastic is a broad name given to different polymers with high molecular weight, which can be degraded by various processes. However, considering their abundance in the environment and their specificity in attacking plastics, biodegradation of plastics by microorganisms and enzymes seems to be the most effective process. When plastics are used as substrates for microorganisms, evaluation of their biodegradability should not only be based on their chemical structure, but also on their physical properties (melting point, glass transition temperature, crystallinity, storage modulus etc.. In this review, microbial and enzymatic biodegradation of plastics and some factors that affect their biodegradability are discussed.

  18. Biodegradability of plastics.

    Science.gov (United States)

    Tokiwa, Yutaka; Calabia, Buenaventurada P; Ugwu, Charles U; Aiba, Seiichi

    2009-08-26

    Plastic is a broad name given to different polymers with high molecular weight, which can be degraded by various processes. However, considering their abundance in the environment and their specificity in attacking plastics, biodegradation of plastics by microorganisms and enzymes seems to be the most effective process. When plastics are used as substrates for microorganisms, evaluation of their biodegradability should not only be based on their chemical structure, but also on their physical properties (melting point, glass transition temperature, crystallinity, storage modulus etc.). In this review, microbial and enzymatic biodegradation of plastics and some factors that affect their biodegradability are discussed.

  19. Helene: A Plastic Model

    Science.gov (United States)

    Umurhan, O. M.; Moore, J. M.; Howard, A. D.; Schenk, P.; White, O. L.

    2014-12-01

    Helene, the Saturnian L4 Trojan satellite co-orbiting Dionne and sitting within the E-ring, possesses an unusual morphology characteristic of broad km-scale basins and depressions and a generally smooth surface patterned with streaks and grooves which are indicative of non-typical mass transport. Elevation angles do not appear to exceed 10o at most. The nature and origin of the surface materials forming these grooved patterns is unknown. Given the low surface gravity (plastic-like flow like a Bingham fluid, we setup and test a number of likely scenarios to explain the observations. The numerical results qualitatively indicate that treating the mass-wasting materials as a Bingham material reproduces many of the qualitative features observed. We also find that in those simulations in which accretion is concomitant with Bingham mass-wasting, the long time-evolution of the surface flow shows intermittency in the total surface activity (defined as total surface integral of the absolute magnitude of the mass-flux). Detailed analyses identify the locations where this activity is most pronounced and we will discuss these and its implications in further detail.

  20. Challenges in plastics recycling

    DEFF Research Database (Denmark)

    Pivnenko, Kostyantyn; Jakobsen, L. G.; Eriksen, Marie Kampmann

    2015-01-01

    Recycling of waste plastics still remains a challenging area in the waste management sector. The current and potential goals proposed on EU or regional levels are difficult to achieve, and even to partially fullfil them the improvements in collection and sorting should be considerable. A study...... was undertaken to investigate the factors affecting quality in plastics recycling. The preliminary results showed factors primarily influencing quality of plastics recycling to be polymer cross contamination, presence of additives, non-polymer impurities, and polymer degradation. Deprivation of plastics quality......, with respect to recycling, has been shown to happen throughout the plastics value chain, but steps where improvements may happen have been preliminary identified. Example of Cr in plastic samples analysed showed potential spreading and accumulation of chemicals ending up in the waste plastics. In order...

  1. A one-piece 3D printed flexure translation stage for open-source microscopy

    Science.gov (United States)

    Sharkey, James P.; Foo, Darryl C. W.; Kabla, Alexandre; Baumberg, Jeremy J.; Bowman, Richard W.

    2016-02-01

    Open source hardware has the potential to revolutionise the way we build scientific instruments; with the advent of readily available 3D printers, mechanical designs can now be shared, improved, and replicated faster and more easily than ever before. However, printed parts are typically plastic and often perform poorly compared to traditionally machined mechanisms. We have overcome many of the limitations of 3D printed mechanisms by exploiting the compliance of the plastic to produce a monolithic 3D printed flexure translation stage, capable of sub-micron-scale motion over a range of 8 × 8 × 4 mm. This requires minimal post-print clean-up and can be automated with readily available stepper motors. The resulting plastic composite structure is very stiff and exhibits remarkably low drift, moving less than 20 μm over the course of a week, without temperature stabilisation. This enables us to construct a miniature microscope with excellent mechanical stability, perfect for time-lapse measurements in situ in an incubator or fume hood. The ease of manufacture lends itself to use in containment facilities where disposability is advantageous and to experiments requiring many microscopes in parallel. High performance mechanisms based on printed flexures need not be limited to microscopy, and we anticipate their use in other devices both within the laboratory and beyond.

  2. Biomechanical evaluation of one-piece and two-piece small-diameter dental implants: In-vitro experimental and three-dimensional finite element analyses.

    Science.gov (United States)

    Wu, Aaron Yu-Jen; Hsu, Jui-Ting; Chee, Winston; Lin, Yun-Te; Fuh, Lih-Jyh; Huang, Heng-Li

    2016-09-01

    Small-diameter dental implants are associated with a higher risk of implant failure. This study used both three-dimensional finite-element (FE) simulations and in-vitro experimental tests to analyze the stresses and strains in both the implant and the surrounding bone when using one-piece (NobelDirect) and two-piece (NobelReplace) small-diameter implants, with the aim of understanding the underlying biomechanical mechanisms. Six experimental artificial jawbone models and two FE models were prepared for one-piece and two-piece 3.5-mm diameter implants. Rosette strain gauges were used for in-vitro tests, with peak values of the principal bone strain recorded with a data acquisition system. Implant stability as quantified by Periotest values (PTV) were also recorded for both types of implants. Experimental data were analyzed statistically using Wilcoxon's rank-sum test. In FE simulations, the peak value and distribution of von-Mises stresses in the implant and bone were selected for evaluation. In in-vitro tests, the peak bone strain was 42% lower for two-piece implants than for one-piece implants. The PTV was slightly lower for one-piece implants (PTV = -6) than for two-piece implants (PTV = -5). In FE simulations, the stresses in the bone and implant were about 23% higher and 12% lower, respectively, for one-piece implants than those for two-piece implants. Due to the higher peri-implant bone stresses and strains, one-piece implants (NobelDirect) might be not suitable for use as small-diameter implants. Copyright © 2016. Published by Elsevier B.V.

  3. High prevalence of parental delivery of plastic debris in Cory's shearwaters (Calonectris diomedea).

    Science.gov (United States)

    Rodríguez, Airam; Rodríguez, Beneharo; Nazaret Carrasco, María

    2012-10-01

    Plastic ingestion by adult Procellariiformes has been widely recorded, but few studies have evaluated intergenerational transfer. We assessed the prevalence of plastic particles, as well as their basic characteristics, in the gut content of dead Cory's shearwater fledglings stranded by light pollution on Canary Islands. Eighty-three percent of birds were affected, containing on average 8.0 plastic pieces per bird. The average plastic weight per bird was low (2.97±3.97mg) compared with other petrel species. We found no relationships between plastic loads and body condition or body size, but negative effects may be hidden or delayed. We propose to use the fledglings stranded by light pollution to carry out more precise studies to understand the potential hidden costs of plastic ingestion; and to monitor in a long-term the marine debris to develop management actions for the control of pollution at the marine environment. Copyright © 2012 Elsevier Ltd. All rights reserved.

  4. Plasticity-induced damage in metals : nonlocal modelling at finite strains

    NARCIS (Netherlands)

    Engelen, R.A.B.

    2005-01-01

    The plasticity models that are generally adopted to predict the response of e.g. a deforming piece of metal assume that the material behaves like a true local continuum. This implies that the evolution of a state variable in a single material point only depends on the material state of that

  5. Production of Methane and Water from Crew Plastic Waste

    Science.gov (United States)

    Captain, Janine; Santiago, Eddie; Parrish, Clyde; Strayer, Richard F.; Garland, Jay L.

    2008-01-01

    Recycling is a technology that will be key to creating a self sustaining lunar outpost. The plastics used for food packaging provide a source of material that could be recycled to produce water and methane. The recycling of these plastics will require some additional resources that will affect the initial estimate of starting materials that will have to be transported from earth, mainly oxygen, energy and mass. These requirements will vary depending on the recycling conditions. The degredation products of these plastics will vary under different atmospheric conditions. An estimate of the the production rate of methane and water using typical ISRU processes along with the plastic recycling will be presented.

  6. A compact cyclic plasticity model with parameter evolution

    DEFF Research Database (Denmark)

    Krenk, Steen; Tidemann, L.

    2017-01-01

    The paper presents a compact model for cyclic plasticity based on energy in terms of external and internal variables, and plastic yielding described by kinematic hardening and a flow potential with an additive term controlling the nonlinear cyclic hardening. The model is basically described by five...... parameters: external and internal stiffness, a yield stress and a limiting ultimate stress, and finally a parameter controlling the gradual development of plastic deformation. Calibration against numerous experimental results indicates that typically larger plastic strains develop than predicted...

  7. Plastic debris in the coastal environment: The invincible threat? Abundance of buried plastic debris on Malaysian beaches.

    Science.gov (United States)

    Fauziah, S H; Liyana, I A; Agamuthu, P

    2015-09-01

    Studies on marine debris have gained worldwide attention since many types of debris have found their way into the food chain of higher organisms. Thus, it is crucial that more focus is given to this area in order to curb contaminations in sea food. This study was conducted to quantify plastic debris buried in sand at selected beaches in Malaysia. Marine debris was identified according to size range and distribution, and this information was related to preventive actions to improve marine waste issues. For the purpose of this study, comparison of plastic waste abundance between a recreational beach and fish-landing beaches was also carried out, since the different beach types represent different activities that produce debris. Six beaches along the Malaysian coastline were selected for this study. The plastic types in this study were related to the functions of the beach. While recreational beaches have abundant quantities of plastic film, foamed plastic including polystyrene, and plastic fragment, fish-landing beaches accumulated line and foamed plastic. A total of 2542 pieces (265.30 g m(-2)) of small plastic debris were collected from all six beaches, with the highest number from Kuala Terengganu, at 879 items m(-2) on Seberang Takir Beach, followed by Batu Burok Beach with 780 items m(-2). Findings from studies of Malaysian beaches have provided a clearer understanding of the distribution of plastic debris. This demonstrates that commitments and actions, such as practices of the 'reduce, reuse, recycle' (3R) approach, supporting public awareness programmes and beach clean-up activities, are essential in order to reduce and prevent plastic debris pollution. © The Author(s) 2015.

  8. Sand moulds milling for one-of-a-kind pieces

    Science.gov (United States)

    Rodríguez, A.; Calleja, A.; Olvera, D.; Peñafiel, F. J.; López de Lacalle, L. N.

    2012-04-01

    Time to market is a critical measurement for today's foundry market. Combining 3D digitizing and sand blocks milling is possible to reduce this time. Avoiding the use of a wood pattern, this technique is useful for art pieces or unique parts, when only one component is necessary. The key of the proposed methodology is to achieve enough tool life with conventional tool qualities, avoiding the risk of sand destruction or damage. A special study of tool wear is presented in this work, studying different tool materials and different sand types. Two examples of unique parts are also presented in this work following the proposed methodology in order to reduce time and cost for the rapid reproduction of very short batches.

  9. Scleral fixation of a single-piece multifocal intraocular lens.

    Science.gov (United States)

    Can, Ertugrul; Basaran, M Resat; Gül, Adem

    2013-01-01

    We describe an ab interno technique for injector implantation of a one-piece multifocal intraocular lens (IOL). Transscleral fixation of multifocal posterior chamber IOL implantation using an injector with ab interno technique was performed in an eye of a 9-year-old girl who had undergone pars plana lensectomy 2 years before for bilateral lens subluxation with unknown etiology. No major complications were encountered during a 3-month follow-up of the patient and excellent centration was observed during the follow-up period. Her preoperative best spectacle-corrected distance visual acuity of 20/32 improved to uncorrected distance visual acuity of 20/25. Closed-loop design of IOL served the function of eyelets and position of the IOL was provided using only a 2-point fixation. Intraoperative position adjustment of the IOL provided an excellent centralization of multifocal IOL.

  10. The RNA silencing pathway: the bits and pieces that matter.

    Directory of Open Access Journals (Sweden)

    2005-07-01

    Full Text Available Cellular pathways are generally proposed on the basis of available experimental knowledge. The proposed pathways, however, may be inadequate to describe the phenomena they are supposed to explain. For instance, by means of concise mathematical models we are able to reveal shortcomings in the current description of the pathway of RNA silencing. The silencing pathway operates by cleaving siRNAs from dsRNA. siRNAs can associate with RISC, leading to the degradation of the target mRNA. We propose and analyze a few small extensions to the pathway: a siRNA degrading RNase, primed amplification of aberrant RNA pieces, and cooperation between aberrant RNA to trigger amplification. These extensions allow for a consistent explanation for various types of silencing phenomena, such as virus induced silencing, transgene and transposon induced silencing, and avoidance of self-reactivity, as well as for differences found between species groups.

  11. Resolving the Aerosol Piece of the Global Climate Picture

    Science.gov (United States)

    Kahn, R. A.

    2017-12-01

    Factors affecting our ability to calculate climate forcing and estimate model predictive skill include direct radiative effects of aerosols and their indirect effects on clouds. Several decades of Earth-observing satellite observations have produced a global aerosol column-amount (AOD) record, but an aerosol microphysical property record required for climate and many air quality applications is lacking. Surface-based photometers offer qualitative aerosol-type classification, and several space-based instruments map aerosol air-mass types under favorable conditions. However, aerosol hygroscopicity, mass extinction efficiency (MEE), and quantitative light absorption, must be obtained from in situ measurements. Completing the aerosol piece of the climate picture requires three elements: (1) continuing global AOD and qualitative type mapping from space-based, multi-angle imagers and aerosol vertical distribution from near-source stereo imaging and downwind lidar, (2) systematic, quantitative in situ observations of particle properties unobtainable from space, and (3) continuing transport modeling to connect observations to sources, and extrapolate limited sampling in space and time. At present, the biggest challenges to producing the needed aerosol data record are: filling gaps in particle property observations, maintaining global observing capabilities, and putting the pieces together. Obtaining the PDFs of key particle properties, adequately sampled, is now the leading observational deficiency. One simplifying factor is that, for a given aerosol source and season, aerosol amounts often vary, but particle properties tend to be repeatable. SAM-CAAM (Systematic Aircraft Measurements to Characterize Aerosol Air Masses), a modest aircraft payload deployed frequently could fill this gap, adding value to the entire satellite data record, improving aerosol property assumptions in retrieval algorithms, and providing MEEs to translate between remote-sensing optical constraints

  12. Two-piece cryopreserved tracheal allotransplantation: an experimental study.

    Science.gov (United States)

    Iyikesici, Tuncel; Tuncozgur, Bulent; Sanli, Maruf; Isik, Ahmet Feridun; Meteroglu, Fatih; Elbeyli, Levent

    2009-10-01

    For successful reconstruction with tracheal allotransplants following long tracheal resections, problems related to the preservation and vascularisation of the tracheal graft have to be solved. In this study, instead of using a long-segment single-piece graft, we used a graft that has been split into two. The aim was to use this graft after cryopreservation in order to ease neo-vascularisation and to maintain tracheal integrity by transplanting it to two separate regions of the dog cervical trachea. This experimental study was conducted in animal laboratories of the medical school on 11 half-blood dogs. The trachea obtained from the first dog was 8 cm in length; it was split into two pieces of 4 cm each and stored in the preservation solution at -80 degrees C for 4 weeks. Following this, the dog was sacrificed. Two 2 cm portions of cervical trachea were excised from the second dog. These parts were then reconstructed with two tracheal grafts of the same length as the cryopreserved ones. Ten dogs that were grouped into five groups of two dogs each underwent the same procedure. The subjects had a bronchoscopic evaluation on the third postoperative week. Anastomosis regions of the test tracheas were resected to be examined histopathologically. Seven subjects were found to have third-degree obstructions during bronchoscopy; two had close to fourth-degree obstructions. In the histopathological examination, contrary to the findings of the bronchoscopies, 75% of the anastomoses had intact epithelium. The cartilage was seen to have well-preserved structural characteristics in all the anastomoses. Twelve anastomoses had moderate, seven mild and one had severe inflammation. All anastomoses had either good or very good level of vascularisation. The integrity of the tracheal epithelium can be maintained with cryopreservation and split anastomosis technique. The cartilage preserves its structural characteristics despite losing its viability, thereby offering an advantage to

  13. Handbook of Plastic Welding

    DEFF Research Database (Denmark)

    Islam, Aminul

    The purpose of this document is to summarize the information about the laser welding of plastic. Laser welding is a matured process nevertheless laser welding of micro dimensional plastic parts is still a big challenge. This report collects the latest information about the laser welding of plastic...... materials and provides an extensive knowhow on the industrial plastic welding process. The objectives of the report include: - Provide the general knowhow of laser welding for the beginners - Summarize the state-of-the-art information on the laser welding of plastics - Find the technological limits in terms...... of design, materials and process - Find the best technology, process and machines adaptive to Sonion’s components - Provide the skills to Sonion’s Design Engineers for successful design of the of the plastic components suitable for the laser welding The ultimate goal of this report is to serve...

  14. Our plastic age.

    Science.gov (United States)

    Thompson, Richard C; Swan, Shanna H; Moore, Charles J; vom Saal, Frederick S

    2009-07-27

    Within the last few decades, plastics have revolutionized our daily lives. Globally we use in excess of 260 million tonnes of plastic per annum, accounting for approximately 8 per cent of world oil production. In this Theme Issue of Philosophical Transactions of the Royal Society, we describe current and future trends in usage, together with the many benefits that plastics bring to society. At the same time, we examine the environmental consequences resulting from the accumulation of waste plastic, the effects of plastic debris on wildlife and concerns for human health that arise from the production, usage and disposal of plastics. Finally, we consider some possible solutions to these problems together with the research and policy priorities necessary for their implementation.

  15. Our plastic age

    Science.gov (United States)

    Thompson, Richard C.; Swan, Shanna H.; Moore, Charles J.; vom Saal, Frederick S.

    2009-01-01

    Within the last few decades, plastics have revolutionized our daily lives. Globally we use in excess of 260 million tonnes of plastic per annum, accounting for approximately 8 per cent of world oil production. In this Theme Issue of Philosophical Transactions of the Royal Society, we describe current and future trends in usage, together with the many benefits that plastics bring to society. At the same time, we examine the environmental consequences resulting from the accumulation of waste plastic, the effects of plastic debris on wildlife and concerns for human health that arise from the production, usage and disposal of plastics. Finally, we consider some possible solutions to these problems together with the research and policy priorities necessary for their implementation. PMID:19528049

  16. Ingested microscopic plastic translocates to the circulatory system of the mussel, Mytilus edulis (L).

    Science.gov (United States)

    Browne, Mark A; Dissanayake, Awantha; Galloway, Tamara S; Lowe, David M; Thompson, Richard C

    2008-07-01

    Plastics debris is accumulating in the environment and is fragmenting into smaller pieces; as it does, the potential for ingestion by animals increases. The consequences of macroplastic debris for wildlife are well documented, however the impacts of microplastic (plastic fragments into smaller particles, the potential for accumulation in the tissues of an organism increases. The short-term pulse exposure used here did not result in significant biological effects. However, plastics are exceedingly durable and so further work using a wider range of organisms, polymers, and periods of exposure will be required to establish the biological consequences of this debris.

  17. Plastic Pollution from Ships

    OpenAIRE

    Čulin, Jelena; Bielić, Toni

    2016-01-01

    The environmental impact of shipping on marine environment includes discharge of garbage. Plastic litter is of particular concern due to abundance, resistance to degradation and detrimental effect on marine biota. According to recently published studies, a further research is required to assess human health risk. Monitoring data indicate that despite banning plastic disposal at sea, shipping is still a source of plastic pollution. Some of the measures to combat the problem are discussed.

  18. ENVIRONMENTAL ISSUE-PLASTIC

    OpenAIRE

    Sunita Shakle

    2017-01-01

    Polythene is the most common plastic, the annual global production is approximately 60 million tones, and its primary use is in packing. Plastic bags pollute soil and waters and kill thousands of marine generalize plastic bags are not biodegradable they clog water ways, spoil the land scape and end up in landfills. Where they may take 1000 year or more to break down into ever smaller particals that continue to pollution the soil and water.

  19. Our plastic age

    OpenAIRE

    Thompson, Richard C.; Swan, Shanna H.; Moore, Charles J.; vom Saal, Frederick S.

    2009-01-01

    Within the last few decades, plastics have revolutionized our daily lives. Globally we use in excess of 260 million tonnes of plastic per annum, accounting for approximately 8 per cent of world oil production. In this Theme Issue of Philosophical Transactions of the Royal Society, we describe current and future trends in usage, together with the many benefits that plastics bring to society. At the same time, we examine the environmental consequences resulting from the accumulation of waste pl...

  20. Transgenerational plasticity is adaptive in the wild.

    Science.gov (United States)

    Galloway, Laura F; Etterson, Julie R

    2007-11-16

    Plants exhibit adaptive responses to light, but it is not known whether parental plants transmit environmental cues that elicit adaptive responses in offspring. We show that offspring life history (annual versus biennial) is influenced by the maternal light environment (understory versus light gap). This transgenerational plasticity is adaptive when offspring are grown in their maternal light environment, where seeds typically disperse. Projections of population growth show that plants that are appropriately cued for their light environment through maternal effects have 3.4 times greater fitness than otherwise. Transgenerational plasticity has evolved in response to natural variation in light and provides a flexible mechanism by which sedentary organisms cope with heterogeneous environments.

  1. Plasticity: modeling & computation

    National Research Council Canada - National Science Library

    Borja, Ronaldo Israel

    2013-01-01

    .... "Plasticity Modeling & Computation" is a textbook written specifically for students who want to learn the theoretical, mathematical, and computational aspects of inelastic deformation in solids...

  2. Synaptic Plasticity and Nociception

    Institute of Scientific and Technical Information of China (English)

    ChenJianguo

    2004-01-01

    Synaptic plasticity is one of the fields that progresses rapidly and has a lot of success in neuroscience. The two major types of synaptie plasticity: long-term potentiation ( LTP and long-term depression (LTD are thought to be the cellular mochanisms of learning and memory. Recently, accumulating evidence suggests that, besides serving as a cellular model for learning and memory, the synaptic plasticity involves in other physiological or pathophysiological processes, such as the perception of pain and the regulation of cardiovascular system. This minireview will focus on the relationship between synaptic plasticity and nociception.

  3. Plastics and health risks.

    Science.gov (United States)

    Halden, Rolf U

    2010-01-01

    By 2010, the worldwide annual production of plastics will surpass 300 million tons. Plastics are indispensable materials in modern society, and many products manufactured from plastics are a boon to public health (e.g., disposable syringes, intravenous bags). However, plastics also pose health risks. Of principal concern are endocrine-disrupting properties, as triggered for example by bisphenol A and di-(2-ethylhexyl) phthalate (DEHP). Opinions on the safety of plastics vary widely, and despite more than five decades of research, scientific consensus on product safety is still elusive. This literature review summarizes information from more than 120 peer-reviewed publications on health effects of plastics and plasticizers in lab animals and humans. It examines problematic exposures of susceptible populations and also briefly summarizes adverse environmental impacts from plastic pollution. Ongoing efforts to steer human society toward resource conservation and sustainable consumption are discussed, including the concept of the 5 Rs--i.e., reduce, reuse, recycle, rethink, restrain--for minimizing pre- and postnatal exposures to potentially harmful components of plastics.

  4. Investigation of plastic debris ingestion by four species of sea turtles collected as bycatch in pelagic Pacific longline fisheries.

    Science.gov (United States)

    Clukey, Katharine E; Lepczyk, Christopher A; Balazs, George H; Work, Thierry M; Lynch, Jennifer M

    2017-07-15

    Ingestion of marine debris is an established threat to sea turtles. The amount, type, color and location of ingested plastics in the gastrointestinal tracts of 55 sea turtles from Pacific longline fisheries from 2012 to 2016 were quantified, and compared across species, turtle length, body condition, sex, capture location, season and year. Six approaches for quantifying amounts of ingested plastic strongly correlated with one another and included: number of pieces, mass, volume and surface area of plastics, ratio of plastic mass to body mass, and percentage of the mass of gut contents consisting of plastic. All olive ridley (n=37), 90% of green (n=10), 80% of loggerhead (n=5) and 0% of leatherback (n=3) turtles had ingested plastic; green turtles ingested significantly more than olive ridleys. Most debris was in the large intestines. No adverse health impacts (intestinal lesions, blockage, or poor body condition) due directly to plastic ingestion were noted. Copyright © 2017. Published by Elsevier Ltd.

  5. Low Abundance of Plastic Fragments in the Surface Waters of the Red Sea

    KAUST Repository

    Martí, Elisa

    2017-11-08

    The floating plastic debris along the Arabian coast of the Red Sea was sampled by using surface-trawling plankton nets. A total of 120 sampling sites were spread out over the near-shore waters along 1,500 km of coastline during seven cruises performed during 2016 and 2017. Plastic debris, dominated by millimeter-sized pieces, was constituted mostly of fragments of rigid objects (73%) followed by pieces of films (17%), fishing lines (6%), and foam (4%). These fragments were mainly made up by polyethylene (69%) and polypropylene (21%). Fibers, likely released from synthetic textiles, were ubiquitous and abundant, although were analyzed independently due to the risk of including non-plastic fibers and airborne contamination of samples in spite of the precautions taken. The plastic concentrations (excluding possible plastic fibers) contrasts with those found in other semi-closed seas, such as the neighboring Mediterranean. They were relatively low all over the Red Sea ( < 50,000 items km; mean ± SD = 3,546 ± 8,154 plastic item km, 1.1 ± 3.0 g km) showing no clear spatial relationship with the distribution of coastal population. Results suggests a low plastic waste input from land as the most plausible explanation for this relative shortage of plastic in the surface waters of the Red Sea; however, the additional intervention of particular processes of surface plastic removal by fish or the filtering activity of the extensive coral reefs along the coastline cannot be discarded. In addition, our study highlights the relevance of determining specific regional conversion rates of mismanaged plastic waste to marine debris, accounting for the role of near-shore activities (e.g., beach tourism, recreational navigation), in order to estimate plastic waste inputs into the ocean.

  6. Low Abundance of Plastic Fragments in the Surface Waters of the Red Sea

    Directory of Open Access Journals (Sweden)

    Elisa Martí

    2017-11-01

    Full Text Available The floating plastic debris along the Arabian coast of the Red Sea was sampled by using surface-trawling plankton nets. A total of 120 sampling sites were spread out over the near-shore waters along 1,500 km of coastline during seven cruises performed during 2016 and 2017. Plastic debris, dominated by millimeter-sized pieces, was constituted mostly of fragments of rigid objects (73% followed by pieces of films (17%, fishing lines (6%, and foam (4%. These fragments were mainly made up by polyethylene (69% and polypropylene (21%. Fibers, likely released from synthetic textiles, were ubiquitous and abundant, although were analyzed independently due to the risk of including non-plastic fibers and airborne contamination of samples in spite of the precautions taken. The plastic concentrations (excluding possible plastic fibers contrasts with those found in other semi-closed seas, such as the neighboring Mediterranean. They were relatively low all over the Red Sea (<50,000 items km−2; mean ± SD = 3,546 ± 8,154 plastic item km−2, 1.1 ± 3.0 g km−2 showing no clear spatial relationship with the distribution of coastal population. Results suggests a low plastic waste input from land as the most plausible explanation for this relative shortage of plastic in the surface waters of the Red Sea; however, the additional intervention of particular processes of surface plastic removal by fish or the filtering activity of the extensive coral reefs along the coastline cannot be discarded. In addition, our study highlights the relevance of determining specific regional conversion rates of mismanaged plastic waste to marine debris, accounting for the role of near-shore activities (e.g., beach tourism, recreational navigation, in order to estimate plastic waste inputs into the ocean.

  7. Enhancement of J estimation for typical nuclear pipes with a circumferential surface crack under tensile load

    International Nuclear Information System (INIS)

    Cho, Doo Ho; Woo, Seung Wan; Choi, Jae Boong; Kim, Young Jin; Chang, Yoon Suk; Jhung, Myung Jo; Choi, Young Hwan

    2010-01-01

    This paper is to report enhancement of engineering J estimation for semi-elliptical surface cracks under tensile load. Firstly, limitation of the sole solution suggested by Zahoor is shown for reliable structural integrity assessment of thin-walled nuclear pipes. An improved solution is then developed based on extensive 3D FE analyses employing deformation plasticity theory for typical nuclear piping materials. It takes over the structure of the existing solution but provides new tabulated plastic influence functions to cover a wide range of pipe geometry and crack shape. Furthermore, to facilitate easy prediction of the plastic influence function, an alternative simple equation is also developed by using a statistical response surface method. The proposed H 1 values can be used for elastic-plastic fracture analyses of thin-walled pipes with a circumferential surface crack subjected to tensile loading

  8. Enhancement of J estimation for typical nuclear pipes with a circumferential surface crack under tensile load

    Energy Technology Data Exchange (ETDEWEB)

    Cho, Doo Ho; Woo, Seung Wan; Choi, Jae Boong; Kim, Young Jin [Sungkyunkwan University, Suwon (Korea, Republic of); Chang, Yoon Suk [Kyung Hee University, Yongin (Korea, Republic of); Jhung, Myung Jo; Choi, Young Hwan [Korea Institute of Nuclear Safety, Daejeon (Korea, Republic of)

    2010-03-15

    This paper is to report enhancement of engineering J estimation for semi-elliptical surface cracks under tensile load. Firstly, limitation of the sole solution suggested by Zahoor is shown for reliable structural integrity assessment of thin-walled nuclear pipes. An improved solution is then developed based on extensive 3D FE analyses employing deformation plasticity theory for typical nuclear piping materials. It takes over the structure of the existing solution but provides new tabulated plastic influence functions to cover a wide range of pipe geometry and crack shape. Furthermore, to facilitate easy prediction of the plastic influence function, an alternative simple equation is also developed by using a statistical response surface method. The proposed H{sub 1} values can be used for elastic-plastic fracture analyses of thin-walled pipes with a circumferential surface crack subjected to tensile loading

  9. Preservation of refrigerated calf meat pieces by ionization

    International Nuclear Information System (INIS)

    Hassouna, M.; Besbes, M.; Ben Hassen, A.; Mahjoub, A.; Maalej, M.

    1998-01-01

    The influence of five 60Co gamma radiation doses in the range of 1 to 5 kGy on chemical composition and bacteriological counts of pieces of calf meat, partially vacuum - packed before treatment, was studied during storage at + 4 degree C up to 28 days. In vivo thermoluminescence dosimetry (TLD) using dosimeters such as lithium fluoride (LiF) was used as a very sensitive procedure to control both dose delivered to the red meat and its degree of uniformity. These two parameters are generally recommended for the quality control of food irradiation process. While ionizing radiation doses of 1 or 2 kGy were unable to increase the shelf life of treated meat, doses of 3, 4 or 5 kGy were very efficient, and adequate to prevent completely the growth of microorganisms indicating faecal contamination such as total coliforms, faecal coliforms and Enterobacteriaceae; they also kept constant the contents of total mesophilic flora and maintained radioresistant psychrotrophic microflora below the value inducing superficial putrefaction of meat (10 7 CFU cntdot g -1 ) at all storage times. Pathogenic germs producing contaminating toxins in foodstuffs such as Salmonella, Staphylococcus aureus and anaerobic sulfite reducing bacteria were totally absent in both control and treated meat. When pieces of meat were irradiated with doses of 3, 4 or 5 kGy, microbial alcalinization and proteolysis revealed by total volatile basic nitrogen were very low during the whole storage period. In addition, total protein did not change as a result of treatment during that period. However, superficial browning and significant variations were observed in water - holding capacity and saturated and unsaturated fatty acids contents in the free fat of treated meat. Ionizing radiation doses had no effect on weight losses and even on the variations of pH after heating of ground calf meat in double boiler at 50, 70 or 90 degree C up to 1 h. However, these modifications very sensitive to cooking temperature

  10. [Application of traditional Chinese medicine reference standards in quality control of Chinese herbal pieces].

    Science.gov (United States)

    Lu, Tu-Lin; Li, Jin-Ci; Yu, Jiang-Yong; Cai, Bao-Chang; Mao, Chun-Qin; Yin, Fang-Zhou

    2014-01-01

    Traditional Chinese medicine (TCM) reference standards plays an important role in the quality control of Chinese herbal pieces. This paper overviewed the development of TCM reference standards. By analyzing the 2010 edition of Chinese pharmacopoeia, the application of TCM reference standards in the quality control of Chinese herbal pieces was summarized, and the problems exiting in the system were put forward. In the process of improving the quality control level of Chinese herbal pieces, various kinds of advanced methods and technology should be used to research the characteristic reference standards of Chinese herbal pieces, more and more reasonable reference standards should be introduced in the quality control system of Chinese herbal pieces. This article discussed the solutions in the aspect of TCM reference standards, and future development of quality control on Chinese herbal pieces is prospected.

  11. Nuclear reactor fuel element containing an end piece for maintaining the column of fuel pellets

    International Nuclear Information System (INIS)

    Pajot, Jacques; Rabellino, Jacques.

    1974-01-01

    The nuclear reactor fuel element described has an end piece for maintaining the column of fuel pellets in position inside the element cladding. This end piece has a central compression spring one end of which presses against the pellets and the other against a plug shaped piece fitted with a seat for the spring, a conical piece with an elastic ring around it diverging towards the end in contact with the spring and a head at the opposite end. The connection between the compression spring and the pellets is through an application piece. A central bore provided in the end piece helps balance the pressure inside the element. This element is particularly intended for liquid metal cooled fast neutron reactors [fr

  12. Individuality in harpsichord performance: disentangling performer- and piece-specific influences on interpretive choices.

    Science.gov (United States)

    Gingras, Bruno; Asselin, Pierre-Yves; McAdams, Stephen

    2013-01-01

    Although a growing body of research has examined issues related to individuality in music performance, few studies have attempted to quantify markers of individuality that transcend pieces and musical styles. This study aims to identify such meta-markers by discriminating between influences linked to specific pieces or interpretive goals and performer-specific playing styles, using two complementary statistical approaches: linear mixed models (LMMs) to estimate fixed (piece and interpretation) and random (performer) effects, and similarity analyses to compare expressive profiles on a note-by-note basis across pieces and expressive parameters. Twelve professional harpsichordists recorded three pieces representative of the Baroque harpsichord repertoire, including three interpretations of one of these pieces, each emphasizing a different melodic line, on an instrument equipped with a MIDI console. Four expressive parameters were analyzed: articulation, note onset asynchrony, timing, and velocity. LMMs showed that piece-specific influences were much larger for articulation than for other parameters, for which performer-specific effects were predominant, and that piece-specific influences were generally larger than effects associated with interpretive goals. Some performers consistently deviated from the mean values for articulation and velocity across pieces and interpretations, suggesting that global measures of expressivity may in some cases constitute valid markers of artistic individuality. Similarity analyses detected significant associations among the magnitudes of the correlations between the expressive profiles of different performers. These associations were found both when comparing across parameters and within the same piece or interpretation, or on the same parameter and across pieces or interpretations. These findings suggest the existence of expressive meta-strategies that can manifest themselves across pieces, interpretive goals, or expressive devices.

  13. Individuality in harpsichord performance: Disentangling performer- and piece-specific influences on interpretive choices

    Directory of Open Access Journals (Sweden)

    Bruno eGingras

    2013-11-01

    Full Text Available Although a growing body of research has examined issues related to individuality in music performance, few studies have attempted to quantify markers of individuality that transcend pieces and musical styles. This study aims to identify such meta-markers by discriminating between influences linked to specific pieces or interpretive goals and performer-specific playing styles, using two complementary statistical approaches: linear mixed models (LMMs to estimate fixed (piece and interpretation and random (performer effects, and similarity analyses to compare expressive profiles on a note-by-note basis across pieces and expressive parameters. Twelve professional harpsichordists recorded three pieces representative of the Baroque harpsichord repertoire, including three interpretations of one of these pieces, each emphasizing a different melodic line, on an instrument equipped with a MIDI console. Four expressive parameters were analyzed: articulation, note onset asynchrony, timing, and velocity. LMMs showed that piece-specific influences were much larger for articulation than for other parameters, for which performer-specific effects were predominant, and that piece-specific influences were generally larger than effects associated with interpretive goals. Some performers consistently deviated from the mean values for articulation and velocity across pieces and interpretations, suggesting that global measures of expressivity may in some cases constitute valid markers of artistic individuality. Similarity analyses detected significant associations among the magnitudes of the correlations between the expressive profiles of different performers. These associations were found both when comparing across parameters and within the same piece or interpretation, or on the same parameter and across pieces or interpretations. These findings suggest the existence of expressive meta-strategies that can manifest themselves across pieces, interpretive goals, or

  14. Creep rupture of mild steel compact tension test pieces

    International Nuclear Information System (INIS)

    Priddle, E.K.

    1978-10-01

    Creep rupture lives have been determined for compact tension and unnotched tensile test pieces of mild steel at 450 0 C. Three sizes of compact tension specimens were used in which the ratios of reference stress to elastic stress intensity factor were 2.76, 4.78 and 6.6 (msup(-1/2)). The analysis of results in terms of either initial reference stress or stress intensity was unable to reduce the data to a single failure curve. An empirical correlation was found between rupture time and a reference stress/crack length combination where t = 2.46 x 10 20 sub(σref) sup(-8.96) asup(-1.56) (units hours, MPa and metres). This equation has no valid application to materials or specimens other than those from which it was derived. Reported data for 1/2Cr Mo V and 2 1/4Cr Mo steels at 565 0 C were also correlated by this approach. (author)

  15. Cohabitants' perspective on housing adaptations: a piece of the puzzle.

    Science.gov (United States)

    Granbom, Marianne; Taei, Afsaneh; Ekstam, Lisa

    2017-12-01

    As part of the Swedish state-funded healthcare system, housing adaptations are used to promote safe and independent living for disabled people in ordinary housing through the elimination of physical environmental barriers in the home. The aim of this study was to describe the cohabitants' expectations and experiences of how a housing adaptation, intended for the partner, would impact their everyday life. In-depth interviews were conducted with cohabitants of nine people applying for a housing adaptation, initially at the time of the application and then again 3 months after the housing adaptation was installed. A longitudinal analysis was performed including analysis procedures from Grounded Theory. The findings revealed the expectations and experiences in four categories: partners' activities and independence; cohabitants' everyday activities and caregiving; couples' shared recreational/leisure activities; and housing decisions. A core category putting the intervention into perspective was called 'Housing adaptations - A piece of the puzzle'. From the cohabitants' perspective, new insights on housing adaptations emerged, which are important to consider when planning and carrying out successful housing adaptations. © 2017 Nordic College of Caring Science.

  16. A comparative study of two-piece ostomy appliances.

    Science.gov (United States)

    Welser, Marion; Riedlinger, Inge; Prause, Ulla

    The quality of life of people with a stoma may be affected by peristomal skin disorders and by frequent unplanned changes of ostomy appliances due to problems with those appliances. The aim of this study was to evaluate two new, two-piece ostomy appliances with mechanical couplings (both from the SenSura range by Coloplast) and their ability to address areas that may be important to the quality of life of people with stomas, including appliance changes, stool seepage and overfilling. The study design featured two comparative, crossover, randomized multi-centre studies that were conducted in Germany. The SenSura appliances were evaluated against established reference appliances. Seventy-three individuals with a colostomy (closed-end appliances) and 75 individuals with an ileostomy (drainable appliances) participated in the studies. The participants tested 4-6 flanges of each type within a maximum period of two weeks. The results demonstrated that there was less seepage of stool observed under the SenSura flange when it was removed (pappliances. The SenSura flanges had better adhesion and flexibility and were easier to remove than the references (pappliances on quality of life indicators - there were fewer unplanned changes and less seepage of stool was observed in patients using the SenSura products.

  17. [Development and innovation of traditional Chinese medicine processing discipline and Chinese herbal pieces industry].

    Science.gov (United States)

    Xiao, Yong-Qing; Li, Li; Liu, Ying; Ma, Yin-Lian; Yu, Ding-Rong

    2016-01-01

    To elucidate the key issues in the development and innovation of traditional Chinese medicine processing discipline and Chinese herbal pieces industry Chinese herbal pieces industry. According to the author's accumulated experience over years and demand of the development of the Chinese herbal pieces industry, the key issues in the development and innovation on the Chinese herbal pieces industry were summarized. According to the author, the traditional Chinese medicine processing discipline shall focus on a application basis research. The development of this discipline should be closely related to the development of Chinese herbal pieces. The traditional Chinese medicine processing discipline can be improved and its results can be transformed only if this discipline were correlated with the Chinese herbal pieces industry, matched with the development of the Chinese herbal pieces industry, and solved the problems in the development on the Chinese herbal pieces industry. The development of traditional Chinese medicine processing discipline and the Chinese herbal pieces industry also requires scientific researchers to make constant innovations, realize the specialty of the researches, and innovate based on inheritance. Copyright© by the Chinese Pharmaceutical Association.

  18. Typicality and misinformation: Two sources of distortion

    Directory of Open Access Journals (Sweden)

    Malen Migueles

    2008-01-01

    Full Text Available This study examined the effect of two sources of memory error: exposure to post-event information and extracting typical contents from schemata. Participants were shown a video of a bank robbery and presented with highand low-typicality misinformation extracted from two normative studies. The misleading suggestions consisted of either changes in the original video information or additions of completely new contents. In the subsequent recognition task the post-event misinformation produced memory impairment. The participants used the underlying schema of the event to extract high-typicality information which had become integrated with episodic information, thus giving rise to more hits and false alarms for these items. However, the effect of exposure to misinformation was greater on low-typicality items. There were no differences between changed or added information, but there were more false alarms when a low-typicality item was changed to a high-typicality item

  19. Suffocation caused by plastic wrap covering the face combined with nitrous oxide inhalation

    DEFF Research Database (Denmark)

    Leth, Peter Mygind; Astrup, Birgitte Schmidt

    2017-01-01

    Suicide using a combination of a plastic bag over the head and inhalation of a non-irritating gas, such as helium, argon or nitrogen, has been reported in the literature. Here an unusual suicide method in a 17-year old man by suffocation from covering the face with household plastic wrap, combined....... The deceased was a 17-year old man who was found with the nose and mouth closed with a piece of kitchen plastic wrap. The plastic wrap had been removed prior to autopsy. Autopsy findings were suggestive of asphyxia, but were otherwise negative. Nitrous oxide was detected in the brain and lung tissue...... with headspace-gas chromatography-mass spectrometry (headspace-GCMS). The cause of death was assumed to be suffocation caused by plastic wrap covering the face, combined with nitrous oxide inhalation. Suicide was suspected because of a history of depression for several months. Nitrous oxide, also known...

  20. Detection of kinetic change points in piece-wise linear single molecule motion

    Science.gov (United States)

    Hill, Flynn R.; van Oijen, Antoine M.; Duderstadt, Karl E.

    2018-03-01

    Single-molecule approaches present a powerful way to obtain detailed kinetic information at the molecular level. However, the identification of small rate changes is often hindered by the considerable noise present in such single-molecule kinetic data. We present a general method to detect such kinetic change points in trajectories of motion of processive single molecules having Gaussian noise, with a minimum number of parameters and without the need of an assumed kinetic model beyond piece-wise linearity of motion. Kinetic change points are detected using a likelihood ratio test in which the probability of no change is compared to the probability of a change occurring, given the experimental noise. A predetermined confidence interval minimizes the occurrence of false detections. Applying the method recursively to all sub-regions of a single molecule trajectory ensures that all kinetic change points are located. The algorithm presented allows rigorous and quantitative determination of kinetic change points in noisy single molecule observations without the need for filtering or binning, which reduce temporal resolution and obscure dynamics. The statistical framework for the approach and implementation details are discussed. The detection power of the algorithm is assessed using simulations with both single kinetic changes and multiple kinetic changes that typically arise in observations of single-molecule DNA-replication reactions. Implementations of the algorithm are provided in ImageJ plugin format written in Java and in the Julia language for numeric computing, with accompanying Jupyter Notebooks to allow reproduction of the analysis presented here.

  1. Determination of resilient modulus values for typical plastic soils in Wisconsin.

    Science.gov (United States)

    2011-09-01

    "The objectives of this research are to establish a resilient modulus test results database and to develop : correlations for estimating the resilient modulus of Wisconsin fine-grained soils from basic soil properties. A : laboratory testing program ...

  2. Plasticity - a limiting case of creep

    International Nuclear Information System (INIS)

    Cords, H.; Kleist, G.; Zimmermann, R.

    1986-11-01

    The present work is an attempt to develop further the so-called unified theory for viscoplastic constitutive equations as used for metals or metal alloys. Typically, in similar approaches creep strains and plastic strains are derived from one common stress-strain relationship for inelastic strain rates employing an internal stress function as a back stress. Some novel concepts concerning the definition of the internal stress, plastic yielding and material hardening have been introduced, formulated mathematically and tested for correspondence with a standard type of materials behaviour. As a result of the investigations a system of simultaneous differential equations is defined which has been used to elaborate a common view on a number of different material effects observed in creep and plasticity i.e. normal and inverted primary creep, recoverable creep, incubation time and anelasticity in stress reduction, negative stress relaxation, plastic yielding, perfect plasticity, negative strain rate sensitivity, serrated flow, strain hardening in monotonic and cyclic loading. The theoretical approach is mainly based on a lateral contraction movement not following rigidly the longitudinal extension of the material specimen by a prescribed constant value of Poisson's ratio as usual, but following the axial extension in a process of drag which allows for retardation and which simultaneously impedes the longitudinal straining. (orig.) [de

  3. Role of Plastics on Human Health.

    Science.gov (United States)

    Kumar, Pramod

    2018-05-01

    Plastics, currently the universal workhorse materials of modern economy, because of their low cost and varied functional properties are posing serious threat to environment and consumer's health in many direct and indirect ways. Rising concern about the impact of plastics on environment and human health, has forced the industry to look for alternatives. This review studies current understanding of benefits and concerns surrounding use of plastics, reviews literature about health effects in humans and discusses the current state of evidence, as well as future research trends. There is increasing concern regarding additives in plastics to which most people are exposed, such as phthalates, bisphenol A or polybrominated diphenyl ethers (PBDE), and their detection in humans, leading to harmful impact on health. The studies are divided, among many other issues on the fact of considering these additives as carcinogens or toxicants, but there is a consensus that these chemicals have the ability to alter the endocrine system. Human data are limited compared to large body of experimental evidence documenting reproductive or developmental toxicity in relation to these compounds in animals. The concentrations of these additives in young children, a segment particularly sensitive to exogenous insults, are typically higher, indicating the need to decrease exposure to these compounds. The rapid increase in usage of plastics and increased awareness about its health hazard has lent urgency to the whole issue.

  4. A Typical Verification Challenge for the GRID

    NARCIS (Netherlands)

    van de Pol, Jan Cornelis; Bal, H. E.; Brim, L.; Leucker, M.

    2008-01-01

    A typical verification challenge for the GRID community is presented. The concrete challenge is to implement a simple recursive algorithm for finding the strongly connected components in a graph. The graph is typically stored in the collective memory of a number of computers, so a distributed

  5. Complex PTSD and phased treatment in refugees: a debate piece

    Directory of Open Access Journals (Sweden)

    F. Jackie June ter Heide

    2016-02-01

    Full Text Available Background: Asylum seekers and refugees have been claimed to be at increased risk of developing complex posttraumatic stress disorder (complex PTSD. Consequently, it has been recommended that refugees be treated with present-centred or phased treatment rather than stand-alone trauma-focused treatment. This recommendation has contributed to a clinical practice of delaying or waiving trauma-focused treatment in refugees with PTSD. Objective: The aim of this debate piece is to defend two theses: (1 that complex trauma leads to complex PTSD in a minority of refugees only and (2 that trauma-focused treatment should be offered to all refugees who seek treatment for PTSD. Methods: The first thesis is defended by comparing data on the prevalence of complex PTSD in refugees to those in other trauma-exposed populations, using studies derived from a systematic review. The second thesis is defended using conclusions of systematic reviews and a meta-analysis of the efficacy of psychotherapeutic treatment in refugees. Results: Research shows that refugees are more likely to meet a regular PTSD diagnosis or no diagnosis than a complex PTSD diagnosis and that prevalence of complex PTSD in refugees is relatively low compared to that in survivors of childhood trauma. Effect sizes for trauma-focused treatment in refugees, especially narrative exposure therapy (NET and culturally adapted cognitive-behaviour therapy (CA-CBT, have consistently been found to be high. Conclusions: Complex PTSD in refugees should not be assumed to be present on the basis of complex traumatic experiences but should be carefully diagnosed using a validated interview. In line with treatment guidelines for PTSD, a course of trauma-focused treatment should be offered to all refugees seeking treatment for PTSD, including asylum seekers.

  6. Incidence of plastic fragments among burrow-nesting seabird colonies on offshore islands in northern New Zealand.

    Science.gov (United States)

    Buxton, Rachel T; Currey, Caitlin A; Lyver, Philip O'B; Jones, Christopher J

    2013-09-15

    Marine plastic pollution is ubiquitous throughout the world's oceans, and has been found in high concentrations in oceanic gyres of both the northern and southern hemispheres. The number of studies demonstrating plastic debris at seabird colonies and plastic ingestion by adult seabirds has increased over the past few decades. Despite the recent discovery of a large aggregation of plastic debris in the South Pacific subtropical gyre, the incidence of plastics at seabird colonies in New Zealand is unknown. Between 2011 and 2012 we surveyed six offshore islands on the northeast coast of New Zealand's North Island for burrow-nesting seabird colonies and the presence of plastic fragments. We found non-research related plastic fragments (0.031 pieces/m(2)) on one island only, Ohinau, within dense flesh-footed shearwater (Puffinus carneipes) colonies. On Ohinau, we found a linear relationship between burrow density and plastic density, with 3.5 times more breeding burrows in areas with plastic fragments found. From these data we conclude that plastic ingestion is a potentially a serious issue for flesh-footed shearwaters in New Zealand. Although these results do not rule out plastic ingestion by other species, they suggest the need for further research on the relationship between New Zealand's pelagic seabirds and marine plastic pollution. Copyright © 2013 Elsevier Ltd. All rights reserved.

  7. Performance-Based Design Optimization of a Transition Piece for Bucket Foundations for Offshore Wind Turbines

    DEFF Research Database (Denmark)

    Nezhentseva, Anastasia; Andersen, Lars; Ibsen, Lars Bo

    2011-01-01

    This paper deals with optimization of the shape of the transition piece connecting turbine column with a suction bucket used as a monopod foundation for an offshore wind turbine. The structural behaviour of a transition piece made of compact reinforced composite (CRC) is analysed. Several...

  8. Short- and Long-Term Musical Preferences: What Makes a Favourite Piece of Music?

    Science.gov (United States)

    Lamont, Alexandra; Webb, Rebecca

    2010-01-01

    Within the growing field of music preferences, little is currently known about the concept of a favourite piece of music. The current study explores listeners' nominated favourite pieces of music over short and longer time-spans, combining diary and interview methods to uncover what a favourite means, how stable it is, and what factors influence…

  9. Stem cell plasticity.

    Science.gov (United States)

    Lakshmipathy, Uma; Verfaillie, Catherine

    2005-01-01

    The central dogma in stem cell biology has been that cells isolated from a particular tissue can renew and differentiate into lineages of the tissue it resides in. Several studies have challenged this idea by demonstrating that tissue specific cell have considerable plasticity and can cross-lineage restriction boundary and give rise to cell types of other lineages. However, the lack of a clear definition for plasticity has led to confusion with several reports failing to demonstrate that a single cell can indeed differentiate into multiple lineages at significant levels. Further, differences between results obtained in different labs has cast doubt on some results and several studies still await independent confirmation. In this review, we critically evaluate studies that report stem cell plasticity using three rigid criteria to define stem cell plasticity; differentiation of a single cell into multiple cell lineages, functionality of differentiated cells in vitro and in vivo, robust and persistent engraft of transplanted cells.

  10. Plastics and environment

    International Nuclear Information System (INIS)

    Avenas, P.

    1996-01-01

    Synthetic organic polymers, such as plastics, PVC, polyamides etc are considered less ecological than natural materials such as wood. Other artificial materials such as metals, glass or biodegradable plastics have also a better image than petroleum products. This short paper demonstrates that the manufacturing or the transport of every material uses energy and that the complete energy balance sheet of a plastic bottle, for instance, is more favourable than the one of a glass bottle. Plastic materials are also easily valorized and recycled and part of the energy spent during manufacturing can be recovered during incineration for district heating. During the life-cycle of such a synthetic material, the same petroleum quantity can be used twice which leads to less negative effects on the environment. Finally, the paper focusses on the problem of biodegradable materials which are not degradable when buried under several meters of wastes and which are a nuisance to recycling. (J.S.)

  11. Plastics: Friend or foe?

    Directory of Open Access Journals (Sweden)

    O P Gupta

    2018-01-01

    Full Text Available Plastics has been playing a very significant role in our life. Being light weight, inexpensive and heving good insulating properties it is being used in all aspects of life, from clothes to contact lenses and from mobile phones to automobiles as well as in medical equipments, However it is not biodegradable, and while degrading to fragments it gets converted in to microplastics and nanoplastics The plastic waste is being recognized as an environmental hazard, since these micr- and nanoplastics find way from landfills to water and foods, It is said that we are not only using, but we are eating, drinking and even braething the plastics. These microplastics in body release certain hazardous chemicals and found to be disrupting functions of certain endocrine organs. Whether the rising prevalence of Diabetes, thyroid disorders or infirtility etc., are realated to the plastics?

  12. Recycling of plastics

    Energy Technology Data Exchange (ETDEWEB)

    Kaminsky, W; Menzel, J; Sinn, H

    1976-01-01

    Considering the shortage of raw materials and environmental pollution, the recycling of plastic waste is a very important topic. Pilot plants for research in Funabashi Japan, Franklin (Ohio) U.S.A., and the R 80-process of Krauss Maffei, W. Germany, have demonstrated the possibility of reclaiming plastics from refuse. Old tires and waste from the plastic producing and manufacturing industries are readily available. The pyrolysis of plastic yields gaseous and liquid products, and the exploitation of this cracking reaction has been demonstrated by pilot plants in Japan and Great Britain. Further laboratory scale experiments are taking place in W. Germany. In continuous fluidized beds and in molten salts, polyethylene, polypropylene, polyvinylchloride, polystyrene and rubber are pyrolysed and better than 98 percent conversion is obtained. Up to 40 percent of the feed can be obtained as aromatic compounds, and a pilot plant is under construction. As a first step PVC-containing material can be almost quantitatively dehydrochlorinated.

  13. A Plastic Menagerie

    Science.gov (United States)

    Hadley, Mary Jane

    2010-01-01

    Bobble heads had become quite popular, depicting all sorts of sports figures, animals, and even presidents. In this article, the author describes how her fourth graders made bobble head sculptures out of empty plastic drink bottles. (Contains 1 online resource.)

  14. Art and Plastic Surgery.

    Science.gov (United States)

    Fernandes, Julio Wilson; Metka, Susanne

    2016-04-01

    The roots of science and art of plastic surgery are very antique. Anatomy, drawing, painting, and sculpting have been very important to the surgery and medicine development over the centuries. Artistic skills besides shape, volume, and lines perception can be a practical aid to the plastic surgeons' daily work. An overview about the interactions between art and plastic surgery is presented, with a few applications to rhinoplasty, cleft lip, and other reconstructive plastic surgeries. This journal requires that authors assign a level of evidence to each article. For a full description of these Evidence-Based Medicine ratings, please refer to the Table of Contents or the online Instructions to Authors www.springer.com/00266.

  15. Marine plastic pollution in waters around Australia: characteristics, concentrations, and pathways.

    Directory of Open Access Journals (Sweden)

    Julia Reisser

    Full Text Available Plastics represent the vast majority of human-made debris present in the oceans. However, their characteristics, accumulation zones, and transport pathways remain poorly assessed. We characterised and estimated the concentration of marine plastics in waters around Australia using surface net tows, and inferred their potential pathways using particle-tracking models and real drifter trajectories. The 839 marine plastics recorded were predominantly small fragments ("microplastics", median length = 2.8 mm, mean length = 4.9 mm resulting from the breakdown of larger objects made of polyethylene and polypropylene (e.g. packaging and fishing items. Mean sea surface plastic concentration was 4256.4 pieces km(-2, and after incorporating the effect of vertical wind mixing, this value increased to 8966.3 pieces km(-2. These plastics appear to be associated with a wide range of ocean currents that connect the sampled sites to their international and domestic sources, including populated areas of Australia's east coast. This study shows that plastic contamination levels in surface waters of Australia are similar to those in the Caribbean Sea and Gulf of Maine, but considerably lower than those found in the subtropical gyres and Mediterranean Sea. Microplastics such as the ones described here have the potential to affect organisms ranging from megafauna to small fish and zooplankton.

  16. Marine Plastic Pollution in Waters around Australia: Characteristics, Concentrations, and Pathways

    Science.gov (United States)

    Reisser, Julia; Shaw, Jeremy; Wilcox, Chris; Hardesty, Britta Denise; Proietti, Maira; Thums, Michele; Pattiaratchi, Charitha

    2013-01-01

    Plastics represent the vast majority of human-made debris present in the oceans. However, their characteristics, accumulation zones, and transport pathways remain poorly assessed. We characterised and estimated the concentration of marine plastics in waters around Australia using surface net tows, and inferred their potential pathways using particle-tracking models and real drifter trajectories. The 839 marine plastics recorded were predominantly small fragments (“microplastics”, median length = 2.8 mm, mean length = 4.9 mm) resulting from the breakdown of larger objects made of polyethylene and polypropylene (e.g. packaging and fishing items). Mean sea surface plastic concentration was 4256.4 pieces km−2, and after incorporating the effect of vertical wind mixing, this value increased to 8966.3 pieces km−2. These plastics appear to be associated with a wide range of ocean currents that connect the sampled sites to their international and domestic sources, including populated areas of Australia's east coast. This study shows that plastic contamination levels in surface waters of Australia are similar to those in the Caribbean Sea and Gulf of Maine, but considerably lower than those found in the subtropical gyres and Mediterranean Sea. Microplastics such as the ones described here have the potential to affect organisms ranging from megafauna to small fish and zooplankton. PMID:24312224

  17. Marine plastic pollution in waters around Australia: characteristics, concentrations, and pathways.

    Science.gov (United States)

    Reisser, Julia; Shaw, Jeremy; Wilcox, Chris; Hardesty, Britta Denise; Proietti, Maira; Thums, Michele; Pattiaratchi, Charitha

    2013-01-01

    Plastics represent the vast majority of human-made debris present in the oceans. However, their characteristics, accumulation zones, and transport pathways remain poorly assessed. We characterised and estimated the concentration of marine plastics in waters around Australia using surface net tows, and inferred their potential pathways using particle-tracking models and real drifter trajectories. The 839 marine plastics recorded were predominantly small fragments ("microplastics", median length = 2.8 mm, mean length = 4.9 mm) resulting from the breakdown of larger objects made of polyethylene and polypropylene (e.g. packaging and fishing items). Mean sea surface plastic concentration was 4256.4 pieces km(-2), and after incorporating the effect of vertical wind mixing, this value increased to 8966.3 pieces km(-2). These plastics appear to be associated with a wide range of ocean currents that connect the sampled sites to their international and domestic sources, including populated areas of Australia's east coast. This study shows that plastic contamination levels in surface waters of Australia are similar to those in the Caribbean Sea and Gulf of Maine, but considerably lower than those found in the subtropical gyres and Mediterranean Sea. Microplastics such as the ones described here have the potential to affect organisms ranging from megafauna to small fish and zooplankton.

  18. Simulation of Double-Seaming in a Two-piece Aluminum Can

    Science.gov (United States)

    Romanko, Anne; Berry, Dale; Fox, David

    2004-06-01

    The aluminum can industry in the United States and Canada manufactures over 100 billion cans per year. Two-piece aluminum cans are commonly used to seal and deliver foodstuffs such as soft drinks, beer, pet food, and other perishable items. In order to ensure product safety and performance, the double seam between the can body and lid is a critical component of the package. Double-seaming is a method by which the flange of the can body and the curl of the end are folded over together such that the final joint is composed of five metal thicknesses. There are a number of design challenges involved with the art of double seaming, especially with the push to lightweight. Although the requirements vary by product, the typical beer package must be able to hold pressures in excess of 90psi. In addition, in production, double seaming is a high-speed operation with speeds as high as 3000 cans/minute on an 18-spindle seamer. For this high volume, low cost industry, understanding and optimizing the seaming process can advance the industry as well as help prevent various manufacturing problems that produce a poor seal between the two pieces of the can. To aid in understanding the mechanics of the can parts during double-seaming, a simulation procedure was developed and carried out on a 202 diameter beverage can and lid. Simulations were run with the explicit dynamics solver ABAQUS/Explicit using the continuum shell element technology available in the ABAQUS general purpose FEA program. The continuum shell is a shear-deformable shell element with the topology of an eight node brick. The element's formulation allows continuously varying, solution-dependent shell thickness and through-thickness pinching stress. One important advantage of using the continuum shell as opposed to a traditional shell element is that true contact interactions at the top and bottom surfaces of the can body and lid can be accurately modeled. With a conventional shell element, contact is performed at the

  19. Simulation of double-seaming in a two-piece aluminum can

    International Nuclear Information System (INIS)

    Romanko, Anne; Berry, Dale; Fox, David

    2004-01-01

    The aluminum can industry in the United States and Canada manufactures over 100 billion cans per year. Two-piece aluminum cans are commonly used to seal and deliver foodstuffs such as soft drinks, beer, pet food, and other perishable items. In order to ensure product safety and performance, the double seam between the can body and lid is a critical component of the package. Double-seaming is a method by which the flange of the can body and the curl of the end are folded over together such that the final joint is composed of five metal thicknesses. There are a number of design challenges involved with the art of double seaming, especially with the push to lightweight. Although the requirements vary by product, the typical beer package must be able to hold pressures in excess of 90psi. In addition, in production, double seaming is a high-speed operation with speeds as high as 3000 cans/minute on an 18-spindle seamer. For this high volume, low cost industry, understanding and optimizing the seaming process can advance the industry as well as help prevent various manufacturing problems that produce a poor seal between the two pieces of the can.To aid in understanding the mechanics of the can parts during double-seaming, a simulation procedure was developed and carried out on a 202 diameter beverage can and lid. Simulations were run with the explicit dynamics solver ABAQUS/Explicit using the continuum shell element technology available in the ABAQUS general purpose FEA program. The continuum shell is a shear-deformable shell element with the topology of an eight node brick. The element's formulation allows continuously varying, solution-dependent shell thickness and through-thickness pinching stress. One important advantage of using the continuum shell as opposed to a traditional shell element is that true contact interactions at the top and bottom surfaces of the can body and lid can be accurately modeled. With a conventional shell element, contact is performed at the

  20. Pyrolysis characteristics of typical biomass thermoplastic composites

    Science.gov (United States)

    Cai, Hongzhen; Ba, Ziyu; Yang, Keyan; Zhang, Qingfa; Zhao, Kunpeng; Gu, Shiyan

    The biomass thermoplastic composites were prepared by extrusion molding method with poplar flour, rice husk, cotton stalk and corn stalk. The thermo gravimetric analyzer (TGA) has also been used for evaluating the pyrolysis process of the composites. The results showed that the pyrolysis process mainly consists of two stages: biomass pyrolysis and the plastic pyrolysis. The increase of biomass content in the composite raised the first stage pyrolysis peak temperature. However, the carbon residue was reduced and the pyrolysis efficiency was better because of synergistic effect of biomass and plastic. The composite with different kinds of biomass have similar pyrolysis process, and the pyrolysis efficiency of the composite with corn stalk was best. The calcium carbonate could inhibit pyrolysis process and increase the first stage pyrolysis peak temperature and carbon residue as a filling material of the composite.

  1. Pyrolysis characteristics of typical biomass thermoplastic composites

    Directory of Open Access Journals (Sweden)

    Hongzhen Cai

    Full Text Available The biomass thermoplastic composites were prepared by extrusion molding method with poplar flour, rice husk, cotton stalk and corn stalk. The thermo gravimetric analyzer (TGA has also been used for evaluating the pyrolysis process of the composites. The results showed that the pyrolysis process mainly consists of two stages: biomass pyrolysis and the plastic pyrolysis. The increase of biomass content in the composite raised the first stage pyrolysis peak temperature. However, the carbon residue was reduced and the pyrolysis efficiency was better because of synergistic effect of biomass and plastic. The composite with different kinds of biomass have similar pyrolysis process, and the pyrolysis efficiency of the composite with corn stalk was best. The calcium carbonate could inhibit pyrolysis process and increase the first stage pyrolysis peak temperature and carbon residue as a filling material of the composite. Keywords: Biomass thermoplastic composite, Calcium carbonate, Pyrolysis characteristic

  2. Incidence of plastic debris in Sooty Tern nests: A preliminary study on Trindade Island, a remote area of Brazil.

    Science.gov (United States)

    de Souza Petersen, Elisa; Krüger, Lucas; Dezevieski, Alexandre; Petry, MariaVirginia; Montone, Rosalinda Carmela

    2016-04-15

    Plastic is abundant in the oceans, reaching pelagic zones away from continents. Here we present the first recordings of plastic used as nest material in Sooty Tern nests, on a remote oceanic island. We describe our findings in terms of quantity, size and color of plastic debris. A total of 78 plastics were noted in 54 nests. Four color categories were found: Blue, White, Green and Red. Blue fragments were the most frequent color, present three times as much as white debris. This pattern was present despite blue fragments being smaller and lighter. The plastic debris of lowest frequency were the larger and heavier pieces (red). To our knowledge this is the first record of plastic in Sooty Tern nests. Trindade Island is on an oceanic zone expected to accumulate garbage due to the dynamic ocean currents. Such findings call for a closer inspection of pollution in the Atlantic Ocean. Copyright © 2016 Elsevier Ltd. All rights reserved.

  3. Plastic pollution in the Labrador Sea: An assessment using the seabird northern fulmar Fulmarus glacialis as a biological monitoring species.

    Science.gov (United States)

    Avery-Gomm, Stephanie; Provencher, Jennifer F; Liboiron, Max; Poon, Florence E; Smith, Paul A

    2018-02-01

    Plastic is now one among one of the most pervasive pollutants on the planet, and ocean circulation models predict that the Arctic will become another accumulation zone. As solutions to address marine plastic emerge, is essential that baselines are available to monitor progress towards targets. The northern fulmar (Fulmarus glacialis), a widely-distributed seabird species, has been used as a biological monitor for plastic pollution in the North Sea, and could be a useful monitoring species elsewhere. We quantified plastic ingested by northern fulmars from the southeastern Canadian waters of the Labrador Sea with the objective of establishing a standardized baseline for future comparisons. Over two years we sampled 70 fulmars and found that 79% had ingested plastic, with an average of 11.6 pieces or 0.151g per bird. Overall, 34% of all fulmars exceeded the Ecological Quality Objective for marine litter, having ingested >0.1g of plastic. Copyright © 2017 Elsevier Ltd. All rights reserved.

  4. DEVELOPMENT OF PLASTIC SURGERY.

    Science.gov (United States)

    Pećanac, Marija Đ

    2015-01-01

    Plastic surgery is a medical specialty dealing with corrections of defects, improvements in appearance and restoration of lost function. Ancient times. The first recorded account of reconstructive plastic surgery was found in ancient Indian Sanskrit texts, which described reconstructive surgeries of the nose and ears. In ancient Greece and Rome, many medicine men performed simple plastic cosmetic surgeries to repair damaged parts of the body caused by war mutilation, punishment or humiliation. In the Middle Ages, the development of all medical braches, including plastic surgery was hindered. New age. The interest in surgical reconstruction of mutilated body parts was renewed in the XVIII century by a great number of enthusiastic and charismatic surgeons, who mastered surgical disciplines and became true artists that created new forms. Modern era. In the XX century, plastic surgery developed as a modern branch in medicine including many types of reconstructive surgery, hand, head and neck surgery, microsurgery and replantation, treatment of burns and their sequelae, and esthetic surgery. Contemporary and future plastic surgery will continue to evolve and improve with regenerative medicine and tissue engineering resulting in a lot of benefits to be gained by patients in reconstruction after body trauma, oncology amputation, and for congenital disfigurement and dysfunction.

  5. Recycling of packing plastics

    International Nuclear Information System (INIS)

    Gintenreiter-Koegl, S.

    2001-05-01

    The ordinance on the avoidance of packaging waste was a serious intervention in the public and private waste management in Austria. Above all the high expenses for an overall packaging waste collection and the recycling of packaging plastics were criticized. The landfill ordinance comes into force in 2004 and this means another major change in the Austrian waste management system. In the course of this change the overall collection and the recycling and recovery of waste streams, especially of the high caloric plastics waste, have to be discussed again. The goal of this work was on the one hand to develop and adapt the hydrocracking process for the recovery of mixed plastics waste and to show a possible application in Austria. On the other hand the work shows the technical, ecological and economical conditions for packaging plastics recycling and recovery in order to find optimum applications for the processes and to examine their contribution to a sustainable development. A hydrocracking test plant for the processing of mixed plastic wastes was built and had been running for about three years. The tests were carried out successfully and the suitability of the technology for the recovery of packaging plastics could be shown. Results show at least a 35 % yield of fuel. The hydrocracking technology is quite common in the oil industries and therefore an integration on a refinery site is suggested. (author)

  6. The use of energy information in plastic scintillator materia

    International Nuclear Information System (INIS)

    Ely, J.; Anderson, K.; Bates, D.; Kouzes, R.; Lo Presti, C.; Runkle, R.; Siciliano, E.; Weier, D.

    2008-01-01

    Plastic scintillator material is often used for gamma-ray detection in many applications due to its relatively good sensitivity and cost-effectiveness compared to other detection materials. However, due to the dominant Compton scattering interaction mechanism, full energy peaks are not observed in plastic scintillator spectra and isotopic identification is impossible. Typically plastic scintillator detectors are solely gross count detectors. In some safeguards and security applications, such as radiation portal monitors for vehicle screening, naturally-occurring radioactive material (NORM) often triggers radiation alarms and results in innocent or nuisance alarms. The limited energy information from plastic scintillator material can be used to discriminate the NORM from targeted materials and reduce the nuisance alarm rate. An overview of the utilization of the energy information from plastic scintillator material will be presented, with emphasis on the detection capabilities and potential limitations for safeguards and security applications. (author)

  7. T-piece resuscitators: how do they compare?

    Science.gov (United States)

    Hinder, Murray; McEwan, Alistair; Drevhammer, Thomas; Donaldson, Snorri; Tracy, Mark Brian

    2018-05-04

    The T-piece resuscitator (TPR) has seen increased use as a primary resuscitation device with newborns. Traditional TPR design uses a high resistance expiratory valve to produce positive end expiratory pressure (PEEP) or continuous positive airway pressure (CPAP) at resuscitation. A new TPR device that uses a dual flow ratio valve (fluidic flip) to produce PEEP/CPAP is now available (rPAP). We aimed to compare the measured ventilation performance of different TPR devices in a controlled bench test study. Single operator provided positive pressure ventilation to an incremental testlung compliance (Crs) model (0.5-5 mL/cmH 2 O) with five different brands of TPR device (Atom, Neopuff, rPAP, GE Panda warmer and Draeger Resuscitaire). At recommended peak inflation pressure (PIP) 20 cmH 2 O, PEEP of 5 cmH 2 O and rate of 60 inflations per minute. 1864 inflations were analysed. Four of the five devices tested demonstrated inadvertent elevations in mean PEEP (5.5-10.3 cmH 2 O, p<0.001) from set value as Crs was increased, while one device (rPAP) remained at the set value. Measured PIP exceeded the set value in two infant warmer devices (GE and Draeger) with inbuilt TPR at Crs of 0.5 (24.5 and 23.5 cmH 2 O, p<0.001). Significant differences were seen in tidal volumes across devices particularly at higher Crs (p<0.001). Results show important variation in delivered ventilation from set values due to inherent TPR device design characteristics with a range of lung compliances expected at birth. Device-generated inadvertent PEEP and overdelivery of PIP may be clinically deleterious for term and preterm newborns or infants with larger Crs during resuscitation. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

  8. Prediction and typicality in multiverse cosmology

    International Nuclear Information System (INIS)

    Azhar, Feraz

    2014-01-01

    In the absence of a fundamental theory that precisely predicts values for observable parameters, anthropic reasoning attempts to constrain probability distributions over those parameters in order to facilitate the extraction of testable predictions. The utility of this approach has been vigorously debated of late, particularly in light of theories that claim we live in a multiverse, where parameters may take differing values in regions lying outside our observable horizon. Within this cosmological framework, we investigate the efficacy of top-down anthropic reasoning based on the weak anthropic principle. We argue contrary to recent claims that it is not clear one can either dispense with notions of typicality altogether or presume typicality, in comparing resulting probability distributions with observations. We show in a concrete, top-down setting related to dark matter, that assumptions about typicality can dramatically affect predictions, thereby providing a guide to how errors in reasoning regarding typicality translate to errors in the assessment of predictive power. We conjecture that this dependence on typicality is an integral feature of anthropic reasoning in broader cosmological contexts, and argue in favour of the explicit inclusion of measures of typicality in schemes invoking anthropic reasoning, with a view to extracting predictions from multiverse scenarios. (paper)

  9. Prediction and typicality in multiverse cosmology

    Science.gov (United States)

    Azhar, Feraz

    2014-02-01

    In the absence of a fundamental theory that precisely predicts values for observable parameters, anthropic reasoning attempts to constrain probability distributions over those parameters in order to facilitate the extraction of testable predictions. The utility of this approach has been vigorously debated of late, particularly in light of theories that claim we live in a multiverse, where parameters may take differing values in regions lying outside our observable horizon. Within this cosmological framework, we investigate the efficacy of top-down anthropic reasoning based on the weak anthropic principle. We argue contrary to recent claims that it is not clear one can either dispense with notions of typicality altogether or presume typicality, in comparing resulting probability distributions with observations. We show in a concrete, top-down setting related to dark matter, that assumptions about typicality can dramatically affect predictions, thereby providing a guide to how errors in reasoning regarding typicality translate to errors in the assessment of predictive power. We conjecture that this dependence on typicality is an integral feature of anthropic reasoning in broader cosmological contexts, and argue in favour of the explicit inclusion of measures of typicality in schemes invoking anthropic reasoning, with a view to extracting predictions from multiverse scenarios.

  10. A Conservative Formulation for Plasticity

    Science.gov (United States)

    1992-01-01

    concepts that apply to a broad class of macroscopic models: plastic deformation and plastic flow rule. CONSERVATIVE PLASTICITY 469 3a. Plastic Defrrnation...temperature. We illustrate these concepts with a model that has been used to describe high strain-rate plastic flow in metals [11, 31, 32]. In the case...JOURDREN, AND P. VEYSSEYRE. Un Modele ttyperelastique- Plastique Euldrien Applicable aux Grandes Dtformations: Que/ques R~sultats 1-D. preprint, 1991. 2. P

  11. How typical are 'typical' tremor characteristics? : Sensitivity and specificity of five tremor phenomena

    NARCIS (Netherlands)

    van der Stouwe, A. M. M.; Elting, J. W.; van der Hoeven, J. H.; van Laar, T.; Leenders, K. L.; Maurits, N. M.; Tijssen, M. Aj.

    Introduction: Distinguishing between different tremor disorders can be challenging. Some tremor disorders are thought to have typical tremor characteristics: the current study aims to provide sensitivity and specificity for five 'typical' tremor phenomena. Methods: Retrospectively, we examined 210

  12. Changes in the Floating Plastic Pollution of the Mediterranean Sea in Relation to the Distance to Land

    Science.gov (United States)

    Petit, Stéphanie; Elineau, Amanda; Bruzaud, Stéphane; Crebassa, Jean-Claude; Dumontet, Bruno; Martí, Elisa; Gorsky, Gabriel; Cózar, Andrés

    2016-01-01

    The composition, size distribution, and abundance of floating plastic debris in surface waters of the Mediterranean Sea were analyzed in relation to distance to land. We combined data from previously published reports with an intensive sampling in inshore waters of the Northwestern Mediterranean. The highest plastic concentrations were found in regions distant from from land as well as in the first kilometer adjacent to the coastline. In this nearshore water strip, plastic concentrations were significantly correlated with the nearness to a coastal human population, with local areas close to large human settlements showing hundreds of thousands of plastic pieces per km2. The ratio of plastic to plankton abundance reached particularly high values for the coastal surface waters. Polyethylene, polypropylene and polyamides were the predominant plastic polymers at all distances from coast (86 to 97% of total items), although the diversity of polymers was higher in the 1-km coastal water strip due to a higher frequency of polystyrene or polyacrylic fibers. The plastic size distributions showed a gradual increase in abundance toward small sizes indicating an efficient removal of small plastics from the surface. Nevertheless, the relative abundance of small fragments (plastic debris in areas closest to Mediterranean coast. The presence of a high concentration of plastic including tiny plastic items could have significant environmental, health and economic impacts. PMID:27556233

  13. Changes in the Floating Plastic Pollution of the Mediterranean Sea in Relation to the Distance to Land.

    Science.gov (United States)

    Pedrotti, Maria Luiza; Petit, Stéphanie; Elineau, Amanda; Bruzaud, Stéphane; Crebassa, Jean-Claude; Dumontet, Bruno; Martí, Elisa; Gorsky, Gabriel; Cózar, Andrés

    2016-01-01

    The composition, size distribution, and abundance of floating plastic debris in surface waters of the Mediterranean Sea were analyzed in relation to distance to land. We combined data from previously published reports with an intensive sampling in inshore waters of the Northwestern Mediterranean. The highest plastic concentrations were found in regions distant from from land as well as in the first kilometer adjacent to the coastline. In this nearshore water strip, plastic concentrations were significantly correlated with the nearness to a coastal human population, with local areas close to large human settlements showing hundreds of thousands of plastic pieces per km2. The ratio of plastic to plankton abundance reached particularly high values for the coastal surface waters. Polyethylene, polypropylene and polyamides were the predominant plastic polymers at all distances from coast (86 to 97% of total items), although the diversity of polymers was higher in the 1-km coastal water strip due to a higher frequency of polystyrene or polyacrylic fibers. The plastic size distributions showed a gradual increase in abundance toward small sizes indicating an efficient removal of small plastics from the surface. Nevertheless, the relative abundance of small fragments (plastic debris in areas closest to Mediterranean coast. The presence of a high concentration of plastic including tiny plastic items could have significant environmental, health and economic impacts.

  14. Measurement of behavior of secondary sealing areas of rotary engine apex seals - Two-piece nonsplit and three-piece slanted horizontal split types

    Science.gov (United States)

    Matsuura, Kenji; Terasaki, Kazuo; Yamane, Katsuki

    1992-12-01

    Behavior measurements have been made with two displacement sensors and an underseal pressure sensor, using an overhanging eccentric shaft-type single-rotor research engine equipped with a packaged multichannel slip ring. The two-piece seal was tilted to the leading and trailing sides of a seal slot during its travel along the rotor housing surface and vibrated on the top end of the leading side of the slot as a fulcrum after the shift from the trailing to the leading side of the slot after the minor axis on the spark plug side. As for the three-piece seal, its top part was also tilted in all operating conditions, although its bottom part made effective area contact with the side of the slot under light load conditions up to medium engine speeds. The working chamber pressure was induced in the underseal in the same manner as with the two-piece type.

  15. Improved airline-type supplied-air plastic suit. [For personnel protection against inhalation of airborne plutonium and tritium

    Energy Technology Data Exchange (ETDEWEB)

    Jolley, L. Jr.; Zippler, D.B.; Cofer, C.H.; Harper, J.A.

    1978-06-01

    Two piece supplied-air plastic suits are used extensively at the Savannah River Plant for personnel protection against inhalation of airborne plutonium and tritium. Worker comfort and noise level problems gave impetus to development of an improved suit and aid distribution system. The resulting plastic suit and development work are discussed. The plastic suit unit cost is less than $20, the hearing zone noise level is less than 75 dBA, protection factors exceed 10,000, and user comfort is approved. This suit is expected to meet performance requirements for unrestricted use.

  16. The plasticity of clays

    Science.gov (United States)

    Group, F.F.

    1905-01-01

    (1) Sand injures plasticity little at first because the grains are suspended in a plastic mass. It is only when grains are abundant enough to come in contact with their neighbors, that the effect becomes serious, and then both strength and amount of possible flow are injured. (2) Certain rare organic colloids increase the plasticity by rendering the water viscous. (3) Fineness also tends to increase plasticity. (4) Plane surfaces (plates) increase the amount of possible flow. They also give a chance for lubrication by thinner films, thus increasing the friction of film, and the strength of the whole mass. The action of plates is thus twofold ; but fineness may be carried to such an extent as to break up plate-like grains into angular fragments. The beneficial effects of plates are also decreased by the fact that each is so closely surrounded by others in the mass. (5) Molecular attraction is twofold in increasing plasticity. As the attraction increases, the coherence and strength of the mass increase, and the amount of possible deformation before crumbling also increases. Fineness increases this action by requiring more water. Colloids and crystalloids in solution may also increase the attraction. It is thus seen to be more active than any other single factor.

  17. Plastics control paraffin buildup

    Energy Technology Data Exchange (ETDEWEB)

    1965-06-01

    Paraffin buildup in producing oil wells has been virtually eliminated by the use of plastic-coated sucker rods. The payout of the plasticing process is generally reached in less than a year, and the paraffin buildup may be inhibited for 10 yr or longer. Most of the plants applying plastic coatings to sucker rods are now fully automated, though a few still offer the hand-sprayed coating that some operators prefer. The several steps involved are described. The ideal plastic for the job is resistant to chemicals at high and low temperatures, flexible, has good adhesion, abrasion resistance, impact resistance, and a smooth glossy finish. The phenol aldehyde and epoxy resins presently offered by the industry fulfill these specifications very well; the multicoating and multibaking techniques improve their performance. Due to wide variations in the severity of the paraffin problem from one oil field to another, there is no general rule to estimate the possible savings from using plastic-coated sucker rods. The process, however, does appear to do a remarkable job in controlling paraffin buildup wherever it is a problem in producing oil by pump.

  18. What is typical is good: The influence of face typicality on perceived trustworthiness

    NARCIS (Netherlands)

    Sofer, C.; Dotsch, R.; Wigboldus, D.H.J.; Todorov, A.T.

    2015-01-01

    The role of face typicality in face recognition is well established, but it is unclear whether face typicality is important for face evaluation. Prior studies have focused mainly on typicality's influence on attractiveness, although recent studies have cast doubt on its importance for attractiveness

  19. Final report on the UKAEA defect detection trials on test pieces 3 and 4. December 1982

    International Nuclear Information System (INIS)

    Lock, D.L.; Cowburn, K.J.

    1983-03-01

    The report follows ND-R-845(R) which described the scope, inspection procedures and results of the defect detection trials on test pieces 3 and 4. The work has been aimed at assessing the ability of non-destructive testing techniques, to detect and size defects near the clad/base metal interface of a flat piece and the inner radius of a PWR inlet nozzle. Following the destructive examination of the test pieces at Ispra, the true sizes of the intended defects are now known. These sizes are compared with that intended and the performance of the inspection teams reviewed. (author)

  20. Collide@CERN: exclusive open rehearsal of Gilles Jobin's last piece

    CERN Multimedia

    2012-01-01

    Collide@CERN and Gilles Jobin, artist in residency at CERN, present an exclusive open rehearsal of his last piece SPIDER GALAXIES Tuesday 31 July 2012 - A new piece created to open new territories of the mind - Join us in Restaurant 1 from 4 p.m. (next to the Glass Box Restaurant) With this piece, the body turns into matter, which is complete, spatial and sensual. Come and see Gilles Jobin and his dancers. With a score by Cristian Vogel and Carla Scaletti invoking sound particles, while Daniel Demont disperses the spectrum. Protean, infinitely large or infinitesimal, such are the Spider Galaxies.    

  1. Investigation of Method for Changing Impression of Musical Piece by Changing its Tempo

    Science.gov (United States)

    Fukumoto, Makoto; Okamatsu, Keita; Matsuo, Kazuhisa

    We propose a simple method that changes impression of musical piece by changing its tempo and investigate psycho-physiological effects of the method with listening experiment. In the experiment, 8 subjects listened same musical pieces with various tempi, and analysis of heartbeat and Semantic-Differential method were used. In 6 out of 10 adjective pairs, inverted-U shapes were observed, and peak tempi of them were different. Moreover, “relaxed” evaluation might be related to listener's heart rate in rest. These results suggest possibility of constructing novel media player that changes impression of musical piece.

  2. Classification of delocalization power of global unitary operations in terms of LOCC one-piece relocalization

    Directory of Open Access Journals (Sweden)

    Akihito Soeda

    2010-06-01

    Full Text Available We study how two pieces of localized quantum information can be delocalized across a composite Hilbert space when a global unitary operation is applied. We classify the delocalization power of global unitary operations on quantum information by investigating the possibility of relocalizing one piece of the quantum information without using any global quantum resource. We show that one-piece relocalization is possible if and only if the global unitary operation is local unitary equivalent of a controlled-unitary operation. The delocalization power turns out to reveal different aspect of the non-local properties of global unitary operations characterized by their entangling power.

  3. Two-phase flow measurements with advanced instrumented spool pieces and local conductivity probes

    International Nuclear Information System (INIS)

    Turnage, K.G.; Davis, C.E.

    1979-01-01

    A series of two-phase, air-water and steam-water tests performed with instrumented spool pieces and with conductivity probes obtained from Atomic Energy of Canada, Ltd. is described. The behavior of the three-beam densitometer, turbine meter, and drag flowmeter is discussed in terms of two-phase models. Application of some two-phase mass flow models to the recorded spool piece data is made and preliminary results are shown. Velocity and void fraction information derived from the conductivity probes is presented and compared to velocities and void fractions obtained using the spool piece instrumentation

  4. Plastic ingestion by Masked booby, Sula dactylatra Lesson, 1831, on Biological Reserve of Rocas Atoll, RN, Brazil

    Directory of Open Access Journals (Sweden)

    Erich de Freitas Mariano

    2012-11-01

    Full Text Available Plastic particles are one of the most common pollutants in the marine environment and it is reaching regions with low human population density. These particles are frequently ingested by many marine organisms, causing digestive problems, which may lead to the weakening and death of the animal. In a research on the feeding of 631-masked boobies, Sula dactylatra from the Biological Reserve of Atol das Rocas, plastic particles were found in stomach contents of four adults. The artifacts found were made of transperant plastic, a piece of label of a mineral water bottle, two pieces of black plastic and a small hard and red piece. The flow of fishing and tourism boats on the Atol das Rocas Biological Reserve may be the source of origin of the plastic parts in both the stomach contents and those found on the islands of the reserve, which suggests that anthropogenic behaviour has already reached isolated areas which should have a high degree of biodiversity protection. Several measures can be taken to avoid deleterious events in the marine biota, but there is great difficulty in avoiding waste dumping from fishing and tourism ships/boats, in addition to that, there are many materials from the mainland, which requires an increase in awareness and supervision.

  5. Plastic pollution of the Kuril-Kamchatka Trench area (NW pacific)

    Science.gov (United States)

    Fischer, Viola; Elsner, Nikolaus O.; Brenke, Nils; Schwabe, Enrico; Brandt, Angelika

    2015-01-01

    During the German-Russian expedition KuramBio (Kuril-Kamchatka Biodiversity Studies) to the northwest Pacific Kuril-Kamchatka Trench and its adjacent abyssal plain, we found several kinds and sizes of plastic debris ranging from fishing nets and packaging to microplastic in the sediment of the deep-sea floor. Microplastics were ubiquitous in the smaller fractions of the box corer samples from every station from depths between 4869 and 5766 m. They were found on the abyssal plain and in the sediments of the trench slope on both sides. The amount of microplastics differed between the stations, with lowest concentration of 60 pieces per m2 and highest concentrations of more than 2000 pieces per m2. Around 75% of the microplastics (defined here as particles plastic debris we found, as a documentation of human impact into the deep sea of this region of the Northwest Pacific.

  6. Plastic in surface waters of the Inside Passage and beaches of the Salish Sea in Washington State.

    Science.gov (United States)

    Davis, Wallace; Murphy, Anne G

    2015-08-15

    We summarize results of two independent studies on plastic pollution in the marine environment that overlap in time and space. One study evaluated the abundance of anthropogenic debris on 37 sandy beaches bordering the Salish Sea in Washington State while the other characterized plastic debris in surface waters of the Salish Sea and the Inside Passage to Skagway, Alaska. Both studies concluded that foam, primarily expanded polystyrene was the dominant pollutant. Plastic was found in surface waters the full length of the Inside Passage but was concentrated near harbors. At the wrack line, an average square meter of Washington's 1180km of sandy beaches in the Salish Sea had 61 pieces of anthropogenic debris weighing approximately 5g. The total loading for the entire 1m wide band is estimated to be 72,000,000 pieces and 5.8metric tons. Most anthropogenic debris on beaches is generated within the region. Copyright © 2015 Elsevier Ltd. All rights reserved.

  7. Investigation into Plastic Cards

    Directory of Open Access Journals (Sweden)

    Neringa Stašelytė

    2015-03-01

    Full Text Available The article examines the strength of laminating plastic cards at different lamination temperatures. For investigation purposes, two types of plastic substrate and films have been used. Laminate strength has been tested (CMYK to establish the impact of colours on the strength of laminate. The paper compares inks supplied by two different producers. The colour characteristics of CIE L*a*b* space before and after the lamination process have been found. According to lamination strength and characteristics of the colours, the most suitable inks, temperature and films have been chosen.

  8. Joining by plastic deformation

    DEFF Research Database (Denmark)

    Mori, Ken-ichiro; Bay, Niels; Fratini, Livan

    2013-01-01

    As the scale and complexity of products such as aircraft and cars increase, demand for new functional processes to join mechanical parts grows. The use of plastic deformation for joining parts potentially offers improved accuracy, reliability and environmental safety as well as creating opportuni......As the scale and complexity of products such as aircraft and cars increase, demand for new functional processes to join mechanical parts grows. The use of plastic deformation for joining parts potentially offers improved accuracy, reliability and environmental safety as well as creating...

  9. Elastic plastic fracture mechanics

    International Nuclear Information System (INIS)

    Simpson, L.A.

    1978-07-01

    The application of linear elastic fracture mechanics (LEFM) to crack stability in brittle structures is now well understood and widely applied. However, in many structural materials, crack propagation is accompanied by considerable crack-tip plasticity which invalidates the use of LEFM. Thus, present day research in fracture mechanics is aimed at developing parameters for predicting crack propagation under elastic-plastic conditions. These include critical crack-opening-displacement methods, the J integral and R-curve techniques. This report provides an introduction to these concepts and gives some examples of their applications. (author)

  10. Typical horticultural products between tradition and innovation

    Directory of Open Access Journals (Sweden)

    Innocenza Chessa

    Full Text Available Recent EU and National policies for agriculture and rural development are mainly focused to foster the production of high quality products as a result of the increasing demand of food safety, typical foods and traditional processing methods. Another word very often used to describe foods in these days is “typicality” which pools together the concepts of “food connected with a specific place”, “historical memory and tradition” and “culture”. The importance for the EU and the National administrations of the above mentioned kind of food is demonstrated, among other things, by the high number of the PDO, PGI and TSG certificated products in Italy. In this period of global markets and economical crisis farmers are realizing how “typical products” can be an opportunity to maintain their market share and to improve the economy of local areas. At the same time, new tools and strategy are needed to reach these goals. A lack of knowledge has being recognized also on how new technologies and results coming from recent research can help in exploiting traditional product and in maintaining the biodiversity. Taking into account the great variety and richness of typical products, landscapes and biodiversity, this report will describe and analyze the relationships among typicality, innovation and research in horticulture. At the beginning “typicality” and “innovation” will be defined also through some statistical features, which ranks Italy at the first place in terms of number of typical labelled products, then will be highlighted how typical products of high quality and connected with the tradition and culture of specific production areas are in a strict relationship with the value of agro-biodiversity. Several different examples will be used to explain different successful methods and/or strategies used to exploit and foster typical Italian vegetables, fruits and flowers. Finally, as a conclusion, since it is thought that

  11. Long-term sorption of metals is similar among plastic types: implications for plastic debris in aquatic environments.

    Directory of Open Access Journals (Sweden)

    Chelsea M Rochman

    Full Text Available Concerns regarding plastic debris and its ability to accumulate large concentrations of priority pollutants in the aquatic environment led us to quantify relationships between different types of mass-produced plastic and metals in seawater. At three locations in San Diego Bay, we measured the accumulation of nine targeted metals (aluminum, chromium, manganese, iron, cobalt, nickel, zinc, cadmium and lead sampling at 1, 3, 6, 9 and 12 months, to five plastic types: polyethylene terephthalate (PET, high-density polyethylene (HDPE, polyvinyl chloride (PVC, low-density polyethylene (LDPE, and polypropylene (PP. Accumulation patterns were not consistent over space and time, and in general all types of plastic tended to accumulate similar concentrations of metals. When we did observe significant differences among concentrations of metals at a single sampling period or location in San Diego Bay, we found that HDPE typically accumulated lesser concentrations of metals than the other four polymers. Furthermore, over the 12-month study period, concentrations of all metals increased over time, and chromium, manganese, cobalt, nickel, zinc and lead did not reach saturation on at least one plastic type during the entire 12-month exposure. This suggests that plastic debris may accumulate greater concentrations of metals the longer it remains at sea. Overall, our work shows that a complex mixture of metals, including those listed as priority pollutants by the US EPA (Cd, Ni, Zn and Pb, can be found on plastic debris composed of various plastic types.

  12. Long-term sorption of metals is similar among plastic types: implications for plastic debris in aquatic environments.

    Science.gov (United States)

    Rochman, Chelsea M; Hentschel, Brian T; Teh, Swee J

    2014-01-01

    Concerns regarding plastic debris and its ability to accumulate large concentrations of priority pollutants in the aquatic environment led us to quantify relationships between different types of mass-produced plastic and metals in seawater. At three locations in San Diego Bay, we measured the accumulation of nine targeted metals (aluminum, chromium, manganese, iron, cobalt, nickel, zinc, cadmium and lead) sampling at 1, 3, 6, 9 and 12 months, to five plastic types: polyethylene terephthalate (PET), high-density polyethylene (HDPE), polyvinyl chloride (PVC), low-density polyethylene (LDPE), and polypropylene (PP). Accumulation patterns were not consistent over space and time, and in general all types of plastic tended to accumulate similar concentrations of metals. When we did observe significant differences among concentrations of metals at a single sampling period or location in San Diego Bay, we found that HDPE typically accumulated lesser concentrations of metals than the other four polymers. Furthermore, over the 12-month study period, concentrations of all metals increased over time, and chromium, manganese, cobalt, nickel, zinc and lead did not reach saturation on at least one plastic type during the entire 12-month exposure. This suggests that plastic debris may accumulate greater concentrations of metals the longer it remains at sea. Overall, our work shows that a complex mixture of metals, including those listed as priority pollutants by the US EPA (Cd, Ni, Zn and Pb), can be found on plastic debris composed of various plastic types.

  13. Keeping it complicated: Mitochondrial genome plasticity across diplonemids.

    Science.gov (United States)

    Valach, Matus; Moreira, Sandrine; Hoffmann, Steve; Stadler, Peter F; Burger, Gertraud

    2017-10-26

    Chromosome rearrangements are important drivers in genome and gene evolution, with implications ranging from speciation to development to disease. In the flagellate Diplonema papillatum (Euglenozoa), mitochondrial genome rearrangements have resulted in nearly hundred chromosomes and a systematic dispersal of gene fragments across the multipartite genome. Maturation into functional RNAs involves separate transcription of gene pieces, joining of precursor RNAs via trans-splicing, and RNA editing by substitution and uridine additions both reconstituting crucial coding sequence. How widespread these unusual features are across diplonemids is unclear. We have analyzed the mitochondrial genomes and transcriptomes of four species from the Diplonema/Rhynchopus clade, revealing a considerable genomic plasticity. Although gene breakpoints, and thus the total number of gene pieces (~80), are essentially conserved across this group, the number of distinct chromosomes varies by a factor of two, with certain chromosomes combining up to eight unrelated gene fragments. Several internal protein-coding gene pieces overlap substantially, resulting, for example, in a stretch of 22 identical amino acids in cytochrome c oxidase subunit 1 and NADH dehydrogenase subunit 5. Finally, the variation of post-transcriptional editing patterns across diplonemids indicates compensation of two adverse trends: rapid sequence evolution and loss of genetic information through unequal chromosome segregation.

  14. Northern fulmars as biological monitors of trends of plastic pollution in the eastern North Pacific.

    Science.gov (United States)

    Avery-Gomm, Stephanie; O'Hara, Patrick D; Kleine, Lydia; Bowes, Victoria; Wilson, Laurie K; Barry, Karen L

    2012-09-01

    Marine plastic debris is a global issue, which highlights the need for internationally standardized methods of monitoring plastic pollution. The stomach contents of beached northern fulmar (Fulmarus glacialis) have proven a cost-effective biomonitor in Europe. However, recent information on northern fulmar plastic ingestion is lacking in the North Pacific. We quantified the stomach contents of 67 fulmars from beaches in the eastern North Pacific in 2009-2010 and found that 92.5% of fulmars had ingested an average of 36.8 pieces, or 0.385 g of plastic. Plastic ingestion in these fulmars is among the highest recorded globally. Compared to earlier studies in the North Pacific, our findings indicate an increase in plastic ingestion over the past 40 years. This study substantiates the use of northern fulmar as biomonitors of plastic pollution in the North Pacific and suggests that the high levels of plastic pollution in this region warrant further monitoring. Copyright © 2012 Elsevier Ltd. All rights reserved.

  15. Co@MWNTs-Plastic: A novel electrode for NaBH4 oxidation

    International Nuclear Information System (INIS)

    Zhang, Dongming; Ye, Ke; Cao, Dianxue; Wang, Bin; Cheng, Kui; Li, Yiju; Wang, Guiling; Xu, Yang

    2015-01-01

    Highlights: • MP substrate was fabricated by adhering MWNTs on a piece of obsoleted plastic bag. • Co nano-thorns were prepared by a simple electrodeposition method on the MP surface. • MP owns a superior stability in strong alkaline environment. • CMP exhibits a high catalytic activity for NaBH 4 electrooxidation. • The possible mechanisms of NaBH 4 electrooxidation on CMP was discussed. - Abstract: A novel multi-walled carbon nanotubes (MWNTs)-Plastic (MP) substrate was first fabricated by adhering MWNTs on a piece of obsoleted plastic bag, and Co nano-thorns were subsequently prepared by a simple electrodeposition method on the MP surface. The morphology and phase structure of the as-prepared Co@MWNTs-Plastic (CMP) catalytic electrode are characterized by scanning electron microscopy, transmission electron microscopy and X-ray diffractometer. The catalytic activity of the CMP electrode for NaBH 4 electrooxidation is investigated by means of cyclic voltammetry and chronoamperometry. The employing of waste plastic bags reduces white pollution and the MP substrate exhibits superior stability in alkaline solution. The 3D CMP catalytic electrode owns a high electrochemical activity for NaBH 4 oxidation. Moreover, we discussed the possible mechanisms of NaBH 4 electrooxidation on the CMP

  16. Product management of making large pieces through Rapid Prototyping PolyJet® technology

    Science.gov (United States)

    Belgiu, G.; Cărăuşu, C.; Şerban, D.; Turc, C. G.

    2017-08-01

    The rapid prototyping process has already become a classic manufacturing process for parts and assemblies, either polymeric or metal parts. Besides the well-known advantages and disadvantages of the process, the use of 3D printers has a great inconvenience: the overall dimensions of the parts are limited. Obviously, there is a possibility to purchase a larger (and more expensive) 3D printer, but there are always larger pieces to be manufactured. One solution to this problem is the splitting of parts into several components that can be manufactured. The component parts can then be assembled in a single piece by known methods such as welding, gluing, screwing, etc. This paper shows our experience in making large pieces on the Strarasys® Objet24 printer, pieces larger than the tray sizes. The results obtained are valid for any 3D printer using the PolyJet® process.

  17. Well-Defined Cyclic Triblock Terpolymers: A Missing Piece of the Morphology Puzzle

    KAUST Repository

    Polymeropoulos, George; Bilalis, Panayiotis; Hadjichristidis, Nikolaos

    2016-01-01

    Two well-defined cyclic triblock terpolymers, missing pieces of the terpolymer morphology puzzle, consisting of poly(isoprene), polystyrene, and poly(2-vinylpyridine), were synthesized by combining the Glaser coupling reaction with anionic

  18. Identifying Typical Movements Among Indoor Objects

    DEFF Research Database (Denmark)

    Radaelli, Laura; Sabonis, Dovydas; Lu, Hua

    2013-01-01

    With the proliferation of mobile computing, positioning systems are becoming available that enable indoor location-based services. As a result, indoor tracking data is also becoming available. This paper puts focus on one use of such data, namely the identification of typical movement patterns...

  19. TYPICAL FORMS OF LIVER PATHOLOGY IN CHILDREN

    Directory of Open Access Journals (Sweden)

    Peter F. Litvitskiy

    2018-01-01

    Full Text Available This lecture for the system of postgraduate medical education analyzes causes, types, key links of pathogenesis, and manifestations of the main typical forms of liver pathology — liver failure, hepatic coma, jaundice, cholemia, acholia, cholelithiasis, and their complications in children. To control the retention of the lecture material, case problems and multiple-choice tests are given.

  20. Typical electric bills, January 1, 1981

    International Nuclear Information System (INIS)

    1981-01-01

    The Typical Electric Bills report is prepared by the Electric Power Division; Office of Coal, Nuclear, Electric and Alternate Fuels; Energy Information Administration; Department of Energy. The publication is geared to a variety of applications by electric utilities, industry, consumes, educational institutions, and government in recognition of the growing importance of energy planning in contemporary society. 19 figs., 18 tabs

  1. Computer Tool for Automatically Generated 3D Illustration in Real Time from Archaeological Scanned Pieces

    OpenAIRE

    Luis López; Germán Arroyo; Domingo Martín

    2012-01-01

    The graphical documentation process of archaeological pieces requires the active involvement of a professional artist to recreate beautiful illustrations using a wide variety of expressive techniques. Frequently, the artist’s work is limited by the inconvenience of working only with the photographs of the pieces he is going to illustrate. This paper presents a software tool that allows the easy generation of illustrations in real time from 3D scanned models. The developed interface allows the...

  2. Composing Interactive Dance Pieces for the MotionComposer, a device for Persons with Disabilities

    OpenAIRE

    Bergsland, Andreas; Wechsler, Robert

    2015-01-01

    The authors have developed a new hardware/software device for persons with disabilities (the MotionComposer), and in the process created a number of interactive dance pieces for non- disabled professional dancers. The paper briefly describes the hardware and motion tracking software of the device before going into more detail concerning the mapping strategies and sound design applied to three interactive dance pieces. The paper concludes by discussing a particular philosophy championing trans...

  3. Nzikitanza – A piece on the resistance against the MUOS in Niscemi , Sicily

    Directory of Open Access Journals (Sweden)

    Marcello Messina

    2015-12-01

    Full Text Available Nzikitanza for accordion, violin, cello and tape was written in 2012 as a reflection on the deployment of Sicilian territory for NATO and US military operations. In particular, the piece was inspired by the then newly formed resistance committee against the MUOS in Niscemi. This brief commentary will illustrate a priori and a posteriori reflections on the status of the piece as a contribution to forms of antagonistic culture.

  4. Application of gamma radiation to the nodes detection in Pinus Radiata (D.Don) wood pieces

    International Nuclear Information System (INIS)

    Morales, J.R.; Dinator, Maria I; Karsulovic C, Jose T.; Leon G, Adolfo

    1996-01-01

    Attenuation of 59.5 KeV photons provided by an Am-241 source, has been used to detect knots in lumber pieces from Pinus Radiata (D.Don). It is shown that the linear attenuation coefficient is a sensitive parameter to detect singularities in the structure of this material. The scanning of the piece provides profiles which define the position and extension of the singularity. (author)

  5. Plastic flashtube chambers

    International Nuclear Information System (INIS)

    Frisken, W.R.

    1977-01-01

    A brief discussion is given of the use and operation of plastic flashtube chambers. Gas leaks, electric pulsing, the glow discharge, and readout methods are considered. Three distinct problems with high rate applications deal with resolving time, dead time, and polarization/neutralization of the chamber

  6. Plastic Surgery: Tackling Misconceptions

    African Journals Online (AJOL)

    will succeed. First impressions tend to last, and if young people's first impression of plastic surgeons is that they spend much of their time doing cosmetic surgery then this is a first impression that might be long ... Res 2014;4 Suppl S3:169‑70. Access this article online. Quick Response Code: Website: www.amhsr.org. DOI:.

  7. Biobased Plastics 2012

    NARCIS (Netherlands)

    Bolck, C.H.; Ravenstijn, J.; Molenveld, K.; Harmsen, P.F.H.

    2011-01-01

    Dit boek geeft inzicht in de huidige op de markt verkrijgbare biobased plastics en de te verwachten ontwikkelingen. Er wordt gekeken naar zowel thermoplastische als thermohardende materialen. Het boek biedt inzicht in de productie, verwerking en eigenschappen van de verschillende types. Daarnaast

  8. New plastic recycling technology

    Science.gov (United States)

    Greater than 60% of the total plastic content of municipal solid waste is comprised of polyolefins (high-density, low-density, and linear polyethylene and polypropylene. Polyethylene (PE) is the largest-volume component but presents a challenge due to the absence of low-energy de...

  9. Reliability of Plastic Slabs

    DEFF Research Database (Denmark)

    Thoft-Christensen, Palle

    1989-01-01

    In the paper it is shown how upper and lower bounds for the reliability of plastic slabs can be determined. For the fundamental case it is shown that optimal bounds of a deterministic and a stochastic analysis are obtained on the basis of the same failure mechanisms and the same stress fields....

  10. Individual differences in behavioural plasticities.

    Science.gov (United States)

    Stamps, Judy A

    2016-05-01

    Interest in individual differences in animal behavioural plasticities has surged in recent years, but research in this area has been hampered by semantic confusion as different investigators use the same terms (e.g. plasticity, flexibility, responsiveness) to refer to different phenomena. The first goal of this review is to suggest a framework for categorizing the many different types of behavioural plasticities, describe examples of each, and indicate why using reversibility as a criterion for categorizing behavioural plasticities is problematic. This framework is then used to address a number of timely questions about individual differences in behavioural plasticities. One set of questions concerns the experimental designs that can be used to study individual differences in various types of behavioural plasticities. Although within-individual designs are the default option for empirical studies of many types of behavioural plasticities, in some situations (e.g. when experience at an early age affects the behaviour expressed at subsequent ages), 'replicate individual' designs can provide useful insights into individual differences in behavioural plasticities. To date, researchers using within-individual and replicate individual designs have documented individual differences in all of the major categories of behavioural plasticities described herein. Another important question is whether and how different types of behavioural plasticities are related to one another. Currently there is empirical evidence that many behavioural plasticities [e.g. contextual plasticity, learning rates, IIV (intra-individual variability), endogenous plasticities, ontogenetic plasticities) can themselves vary as a function of experiences earlier in life, that is, many types of behavioural plasticity are themselves developmentally plastic. These findings support the assumption that differences among individuals in prior experiences may contribute to individual differences in behavioural

  11. T-piece resuscitator versus self-inflating bag for preterm resuscitation: an institutional experience.

    Science.gov (United States)

    Jayaram, Archana; Sima, Adam; Barker, Gail; Thacker, Leroy R

    2013-07-01

    Manual ventilation in the delivery room is provided with devices such as self-inflating bags (SIBs), flow-inflating bags, and T-piece resuscitators. To compare the effect of type of manual ventilation device on overall response to resuscitation among preterm neonates born at Apgar score. Secondary outcomes were incidence of air leaks, need for chest compressions/epinephrine, need for intubation, and surfactant use. We identified 294 resuscitations requiring ventilation. SIB was used for 135 neonates, and T-piece was used for 159 neonates. There was no significant difference between the 1-min and 5-min Apgar scores between SIB and T-piece (P = .77 and P = .11, respectively), nor were there significant differences in secondary outcomes. The rate of rise of Apgar score was higher, by 0.47, with T-piece, compared to SIB (95% CI 0.08-0.87, P = .02). Although some manikin studies favor T-piece for providing reliable and consistent pressures, our experience did not indicate significant differences in effectiveness of resuscitation between the T-piece and SIB in preterm resuscitations.

  12. Pay Matters: The Piece Rate and Health in the Developing World.

    Science.gov (United States)

    Davis, Mary E

    Piece rate pay remains a common form of compensation in developing-world industries. While the piece rate may boost productivity, it has been shown to have unintended consequences for occupational safety and health, including increased accident and injury risk. This paper explores the relationship between worker pay and physical and emotional health, and questions the modern day business case for piece rate pay in the developing world. The relationship between piece rate and self-reported measures of physical and emotional health is estimated using a large survey of garment workers in 109 Vietnamese factories between 2010 and 2014. A random effects logit model controls for factory and year, predicting worker health as a function of pay type, demographics, and factory characteristics. Workers paid by the piece report worse physical and emotional health than workers paid by the hour (OR = 1.38-1.81). Wage incentives provide the most consistently significant evidence of all demographic and factory-level variables, including the factory's own performance on occupational safety and health compliance measures. These results highlight the importance of how workers are paid to understanding the variability in worker health outcomes. More research is needed to better understand the business case supporting the continued use of piece rate pay in the developing world. Copyright © 2016 The Author. Published by Elsevier Inc. All rights reserved.

  13. Plasticity characteristic obtained by indentation

    International Nuclear Information System (INIS)

    Mil'man, Yu.V.; Chugunova, S.I.; Goncharova, I.V.

    2011-01-01

    Methods for determination plasticity characteristic δH in the measurement of hardness and nanohardness are considered. Parameter δH characterizes the plasticity of a material by the part of plastic deformation in the total elastic-plastic deformation. The value of δH is defined for metals with different types of crystal lattice, covalent and partially covalent crystals, intermetallics, metallic glasses and quasicrystals. It is discussed the dependence of the plasticity characteristic δH on structural factors and temperature. Parameter δH allows to analyze and compare the plasticity of materials which are brittle at standard mechanical tests. The combination of hardness H, as the strength characteristic, and the plasticity characteristic δH makes possible the better characterization of mechanical behavior of materials than only the hardness H. The examples of plasticity characteristic δH application are represented.

  14. Plastic pollutants in water environment

    OpenAIRE

    Mrowiec Bożena

    2017-01-01

    Nowadays, wide applications of plastics result in plastic waste being present in the water environment in a wide variety of sizes. Plastic wastes are in water mainly as microplastics (the size range of 1 nm to < 5 mm). Microplastics have been recognized as an emerging threat, as well as ecotoxicological and ecological risk for water ecosystems. In this review are presented some of the physicochemical properties of plastic materials that determine their toxic effect on the aquatic environment....

  15. Monitoring plastic ingestion by the northern fulmar Fulmarus glacialis in the North Sea

    Energy Technology Data Exchange (ETDEWEB)

    Franeker, Jan A. van, E-mail: Jan.vanfraneker@wur.nl [IMARES Institute for Marine Resources and Ecosystem Studies, Wageningen-UR, PO Box 167, 1790AD Den Burg, Texel (Netherlands); Blaize, Christine [Le CHENE, Centre de Sauvegarde de la Faune Sauvage et Musee de la Nature, 12 Rue du Musee, F-76190 Allouville-Bellefosse (France); Danielsen, Johannis [Norouri i Sundum 7, FO-410 Kollafjorour (Faroe Islands); Fairclough, Keith [Fairclough Ecological Orkney FEO Viewforth, Swannay by Evie, Orkney, KW17 2NR, Scotland (United Kingdom); Gollan, Jane [Kermouroux, FR-56 470 Saint Philibert (France); Guse, Nils [Research and Technology Centre West coast FTZ, University of Kiel, Hafentoern 1, D-25761 Buesum (Germany); Hansen, Poul-Lindhard [Naturhistorisk Museum Skagen, Skagen Naturcenter, Flagbakkevej 30, DK-9990 Skagen (Denmark); Heubeck, Martin [University of Aberdeen (SOTEAG), Sumburgh Head Lighthouse, Virkie, Shetland ZE3 9JN, Scotland (United Kingdom); Jensen, Jens-Kjeld [Zoological conservator, I Geilini 37, FO-270 Nolsoy (Faroe Islands); Le Guillou, Gilles [Groupe Ornithologique Normand, 118 route d' ORCHER, F-76700 Gonfreville l' Orcher (France); Olsen, Bergur [Faroe Marine Research Institute c/o Natturugripasavnio, Futalag 40, FO-100 Torshavn (Faroe Islands); Olsen, Kare-Olav [Postveien 43, N-4563 Borhaug (Norway); Pedersen, John [Skagen Uddannelsescenter SUC, Vestmolen 15, DK-9990 Skagen (Denmark); Stienen, Eric W.M. [Research Institute for Nature and Forest, Kliniekstraat 25, B-1070 Brussels (Belgium); Turner, Daniel M. [9 Haswell Gardens, North Shields, Tyne and Wear, NE30 2DP, England (United Kingdom)

    2011-10-15

    The abundance of plastics in stomachs of northern fulmars from the North Sea is used in the OSPAR Ecological Quality Objective (EcoQO) for marine litter. The preliminary EcoQO defines acceptable ecological quality as the situation where no more than 10% of fulmars exceed a critical level of 0.1 g of plastic in the stomach. During 2003-2007, 95% of 1295 fulmars sampled in the North Sea had plastic in the stomach (on average 35 pieces weighing 0.31 g) and the critical level of 0.1 g of plastic was exceeded by 58% of birds, with regional variations ranging from 48 to 78%. Long term data for the Netherlands since the 1980s show a decrease of industrial, but an increase of user plastics, with shipping and fisheries as the main sources. The EcoQO is now also used as an indicator for Good Environmental Status in the European Marine Strategy Framework Directive. - Highlights: > Trends in marine debris can be monitored by plastics in stomachs of seabirds. > In the North Sea 95% of Fulmars has plastic in the stomach (35 particles; 0.31 g). > The policy target is that less than 10% of Fulmars has over 0.1 g of plastic. > Currently 58% of North Sea fulmars exceeds the 0.1 g critical limit. > Over the past 30 years industrial plastics decreased and user plastic increased. - Trends and patterns in the abundance of plastics in northern fulmar stomachs show that seabirds can be a valuable tool for monitoring marine litter.

  16. Monitoring plastic ingestion by the northern fulmar Fulmarus glacialis in the North Sea

    International Nuclear Information System (INIS)

    Franeker, Jan A. van; Blaize, Christine; Danielsen, Johannis; Fairclough, Keith; Gollan, Jane; Guse, Nils; Hansen, Poul-Lindhard; Heubeck, Martin; Jensen, Jens-Kjeld; Le Guillou, Gilles; Olsen, Bergur; Olsen, Kare-Olav; Pedersen, John; Stienen, Eric W.M.; Turner, Daniel M.

    2011-01-01

    The abundance of plastics in stomachs of northern fulmars from the North Sea is used in the OSPAR Ecological Quality Objective (EcoQO) for marine litter. The preliminary EcoQO defines acceptable ecological quality as the situation where no more than 10% of fulmars exceed a critical level of 0.1 g of plastic in the stomach. During 2003-2007, 95% of 1295 fulmars sampled in the North Sea had plastic in the stomach (on average 35 pieces weighing 0.31 g) and the critical level of 0.1 g of plastic was exceeded by 58% of birds, with regional variations ranging from 48 to 78%. Long term data for the Netherlands since the 1980s show a decrease of industrial, but an increase of user plastics, with shipping and fisheries as the main sources. The EcoQO is now also used as an indicator for Good Environmental Status in the European Marine Strategy Framework Directive. - Highlights: → Trends in marine debris can be monitored by plastics in stomachs of seabirds. → In the North Sea 95% of Fulmars has plastic in the stomach (35 particles; 0.31 g). → The policy target is that less than 10% of Fulmars has over 0.1 g of plastic. → Currently 58% of North Sea fulmars exceeds the 0.1 g critical limit. → Over the past 30 years industrial plastics decreased and user plastic increased. - Trends and patterns in the abundance of plastics in northern fulmar stomachs show that seabirds can be a valuable tool for monitoring marine litter.

  17. Printed thermoplastic modular piece, P.T.M.P. = Piezas termoplásticas modulares, P.T.M.P.

    Directory of Open Access Journals (Sweden)

    Sandra Moyano Sanz

    2018-04-01

    Full Text Available This research tries to design a modular part suitable for construction, with new materials and manufacturing processes. Polymers and 3D printing are the key elements in the process. It is about implanting a new model of modular part that is able to replace the conventional brick. With this research, we want to make known the new construction processes derived from 3D printing and how we can improve the existing technology. The main objective is to design a modular part, using additive manufacturing systems and plastic materials. Then we are going to determine the physical characteristics that the pieces must have, and the geometric possibilities that the manufacturing process allows us, as well as the materials that the pieces will be made. These pieces will be subject to all the actual tests to ceramic pieces, according to the current standard. Additionally, we will analyze the results obtained and compare them with an expensive ceramic brick to assess the advantages obtained. Finally, we will determine some conclusions derived from these investigations, and propose new study proposals. With this research, we intend to demonstrate that, although conventional brick are basic elements of construction and fulfils its functions perfectly, it is time to adapt the new technologies to the constructive methods. Resumen Este estudio trata de diseñar una pieza modular apropiada para la construcción mediante nuevos procesos de producción y nuevos materiales. Los polímeros y la impresión 3D son los elementos clave del proceso. Además, se estudia implantar un nuevo modelo de pieza modular que sea capaz de sustituir al ladrillo convencional. Con esta investigación queremos divulgar los nuevos procesos asociados a la impresión 3D y como podemos mejorar la tecnología existente. El objetivo principal es diseñar una pieza modular, usando sistemas de fabricación aditiva y materiales plásticos. Posteriormente vamos a determinar las características f

  18. Herpes zoster - typical and atypical presentations.

    Science.gov (United States)

    Dayan, Roy Rafael; Peleg, Roni

    2017-08-01

    Varicella- zoster virus infection is an intriguing medical entity that involves many medical specialties including infectious diseases, immunology, dermatology, and neurology. It can affect patients from early childhood to old age. Its treatment requires expertise in pain management and psychological support. While varicella is caused by acute viremia, herpes zoster occurs after the dormant viral infection, involving the cranial nerve or sensory root ganglia, is re-activated and spreads orthodromically from the ganglion, via the sensory nerve root, to the innervated target tissue (skin, cornea, auditory canal, etc.). Typically, a single dermatome is involved, although two or three adjacent dermatomes may be affected. The lesions usually do not cross the midline. Herpes zoster can also present with unique or atypical clinical manifestations, such as glioma, zoster sine herpete and bilateral herpes zoster, which can be a challenging diagnosis even for experienced physicians. We discuss the epidemiology, pathophysiology, diagnosis and management of Herpes Zoster, typical and atypical presentations.

  19. Metabolic disorders with typical alterations in MRI

    International Nuclear Information System (INIS)

    Warmuth-Metz, M.

    2010-01-01

    The classification of metabolic disorders according to the etiology is not practical for neuroradiological purposes because the underlying defect does not uniformly transform into morphological characteristics. Therefore typical MR and clinical features of some easily identifiable metabolic disorders are presented. Canavan disease, Pelizaeus-Merzbacher disease, Alexander disease, X-chromosomal adrenoleukodystrophy and adrenomyeloneuropathy, mitochondrial disorders, such as MELAS (mitochondrial encephalopathy, lactic acidosis, and stroke-like episodes) and Leigh syndrome as well as L-2-hydroxyglutaric aciduria are presented. (orig.) [de

  20. Gelatin films plasticized with a simulated biodiesel coproduct stream

    Directory of Open Access Journals (Sweden)

    2009-04-01

    Full Text Available In order to explore the possibility of substituting an unrefined biodiesel coproduct stream (BCS for refined glycerol as a polymer plasticizer we have prepared cast gelatin films plasticized with a simulated BCS, i.e., mixtures of glycerol and some of the typical components found in BCS (methyl linoleate, methyl oleate, linoleic acid, and oleic acid. We measured the tensile properties as a function of plasticizer composition, and analyzed the specific effect of each individual component on tensile properties. We found that it is the unrecovered alkyl esters that largely determine the tensile properties, and that BCS can be successfully used to plasticize cast gelatin films as long as the BCS contains 11 parts by weight, or less, of unrecovered alkyl esters per 100 parts glycerol.

  1. [Typical atrial flutter: Diagnosis and therapy].

    Science.gov (United States)

    Thomas, Dierk; Eckardt, Lars; Estner, Heidi L; Kuniss, Malte; Meyer, Christian; Neuberger, Hans-Ruprecht; Sommer, Philipp; Steven, Daniel; Voss, Frederik; Bonnemeier, Hendrik

    2016-03-01

    Typical, cavotricuspid-dependent atrial flutter is the most common atrial macroreentry tachycardia. The incidence of atrial flutter (typical and atypical forms) is age-dependent with 5/100,000 in patients less than 50 years and approximately 600/100,000 in subjects > 80 years of age. Concomitant heart failure or pulmonary disease further increases the risk of typical atrial flutter.Patients with atrial flutter may present with symptoms of palpitations, reduced exercise capacity, chest pain, or dyspnea. The risk of thromboembolism is probably similar to atrial fibrillation; therefore, the same antithrombotic prophylaxis is required in atrial flutter patients. Acutely symptomatic cases may be subjected to cardioversion or pharmacologic rate control to relieve symptoms. Catheter ablation of the cavotricuspid isthmus represents the primary choice in long-term therapy, associated with high procedural success (> 97 %) and low complication rates (0.5 %).This article represents the third part of a manuscript series designed to improve professional education in the field of cardiac electrophysiology. Mechanistic and clinical characteristics as well as management of isthmus-dependent atrial flutter are described in detail. Electrophysiological findings and catheter ablation of the arrhythmia are highlighted.

  2. What Is Typical Is Good : The Influence of Face Typicality on Perceived Trustworthiness

    NARCIS (Netherlands)

    Sofer, Carmel; Dotsch, Ron; Wigboldus, Daniel H J; Todorov, Alexander

    2015-01-01

    The role of face typicality in face recognition is well established, but it is unclear whether face typicality is important for face evaluation. Prior studies have focused mainly on typicality’s influence on attractiveness, although recent studies have cast doubt on its importance for attractiveness

  3. Introduction to Computational Plasticity

    International Nuclear Information System (INIS)

    Hartley, P

    2006-01-01

    The focus of the book on computational plasticity embodies techniques of relevance not only to academic researchers, but also of interest to industrialists engaged in the production of components using bulk or sheet forming processes. Of particular interest is the guidance on how to create modules for use with the commercial system Abaqus for specific types of material behaviour. The book is in two parts, the first of which contains six chapters, starting with microplasticity, but predominantly on continuum plasticity. The first chapter on microplasticty gives a brief description of the grain structure of metals and the existence of slip systems within the grains. This provides an introduction to the concept of incompressibility during plastic deformation, the nature of plastic yield and the importance of the critically resolved shear stress on the slip planes (Schmid's law). Some knowledge of the notation commonly used to describe slip systems is assumed, which will be familiar to students of metallurgy, but anyone with a more general engineering background may need to undertake additional reading to understand the various descriptions. Chapter two introduces one of several yield criteria, that normally attributed to von Mises (though historians of mechanics might argue over who was first to develop the theory of yielding associated with strain energy density), and its two or three-dimensional representation as a yield surface. The expansion of the yield surface during plastic deformation, its translation due to kinematic hardening and the Bauschinger effect in reversed loading are described with a direct link to the material stress-strain curve. The assumption, that the increment of strain is normal to the yield surface, the normality principle, is introduced. Uniaxial loading of an elastic-plastic material is used as an example in which to develop expressions to describe increments in stress and strain. The full presentation of numerous expressions, tensors and

  4. Termination of plastic-clad fiber

    International Nuclear Information System (INIS)

    Nance, W.R.

    1982-03-01

    Optical waveguides are ideal in a nuclear weapon environment because of their resistance to electromagnetic interference. Of the fibers on today's market, plastic-clad silica (PCS) is the most radiation resistant and therfore the best choice. Because terminating PCS is complex, this paper attemps to address the major problems associated with these terminations including selecting the proper connector and optimizing the terminating procedures. The sources of losses in the connectors are summarized and typical loss values are given for four connectors which were tested

  5. Plasticity modeling & computation

    CERN Document Server

    Borja, Ronaldo I

    2013-01-01

    There have been many excellent books written on the subject of plastic deformation in solids, but rarely can one find a textbook on this subject. “Plasticity Modeling & Computation” is a textbook written specifically for students who want to learn the theoretical, mathematical, and computational aspects of inelastic deformation in solids. It adopts a simple narrative style that is not mathematically overbearing, and has been written to emulate a professor giving a lecture on this subject inside a classroom. Each section is written to provide a balance between the relevant equations and the explanations behind them. Where relevant, sections end with one or more exercises designed to reinforce the understanding of the “lecture.” Color figures enhance the presentation and make the book very pleasant to read. For professors planning to use this textbook for their classes, the contents are sufficient for Parts A and B that can be taught in sequence over a period of two semesters or quarters.

  6. Piecing together the puzzle: Improving event content coverage for real-time sub-event detection using adaptive microblog crawling.

    Directory of Open Access Journals (Sweden)

    Laurissa Tokarchuk

    Full Text Available In an age when people are predisposed to report real-world events through their social media accounts, many researchers value the benefits of mining user generated content from social media. Compared with the traditional news media, social media services, such as Twitter, can provide more complete and timely information about the real-world events. However events are often like a puzzle and in order to solve the puzzle/understand the event, we must identify all the sub-events or pieces. Existing Twitter event monitoring systems for sub-event detection and summarization currently typically analyse events based on partial data as conventional data collection methodologies are unable to collect comprehensive event data. This results in existing systems often being unable to report sub-events in real-time and often in completely missing sub-events or pieces in the broader event puzzle. This paper proposes a Sub-event detection by real-TIme Microblog monitoring (STRIM framework that leverages the temporal feature of an expanded set of news-worthy event content. In order to more comprehensively and accurately identify sub-events this framework first proposes the use of adaptive microblog crawling. Our adaptive microblog crawler is capable of increasing the coverage of events while minimizing the amount of non-relevant content. We then propose a stream division methodology that can be accomplished in real time so that the temporal features of the expanded event streams can be analysed by a burst detection algorithm. In the final steps of the framework, the content features are extracted from each divided stream and recombined to provide a final summarization of the sub-events. The proposed framework is evaluated against traditional event detection using event recall and event precision metrics. Results show that improving the quality and coverage of event contents contribute to better event detection by identifying additional valid sub-events. The

  7. Piecing together the puzzle: Improving event content coverage for real-time sub-event detection using adaptive microblog crawling.

    Science.gov (United States)

    Tokarchuk, Laurissa; Wang, Xinyue; Poslad, Stefan

    2017-01-01

    In an age when people are predisposed to report real-world events through their social media accounts, many researchers value the benefits of mining user generated content from social media. Compared with the traditional news media, social media services, such as Twitter, can provide more complete and timely information about the real-world events. However events are often like a puzzle and in order to solve the puzzle/understand the event, we must identify all the sub-events or pieces. Existing Twitter event monitoring systems for sub-event detection and summarization currently typically analyse events based on partial data as conventional data collection methodologies are unable to collect comprehensive event data. This results in existing systems often being unable to report sub-events in real-time and often in completely missing sub-events or pieces in the broader event puzzle. This paper proposes a Sub-event detection by real-TIme Microblog monitoring (STRIM) framework that leverages the temporal feature of an expanded set of news-worthy event content. In order to more comprehensively and accurately identify sub-events this framework first proposes the use of adaptive microblog crawling. Our adaptive microblog crawler is capable of increasing the coverage of events while minimizing the amount of non-relevant content. We then propose a stream division methodology that can be accomplished in real time so that the temporal features of the expanded event streams can be analysed by a burst detection algorithm. In the final steps of the framework, the content features are extracted from each divided stream and recombined to provide a final summarization of the sub-events. The proposed framework is evaluated against traditional event detection using event recall and event precision metrics. Results show that improving the quality and coverage of event contents contribute to better event detection by identifying additional valid sub-events. The novel combination of

  8. Sub-nanosecond plastic scintillators

    International Nuclear Information System (INIS)

    Lyons, P.B.; Caldwell, S.E.; Hocker, L.P.; Crandall, D.G.; Zagarino, P.A.; Cheng, J.; Tirsell, G.; Hurlbut, C.R.

    1977-01-01

    Quenched plastic scintillators have been developed that yield much faster short decay components and greatly reduced long decay components compared to conventional plastic scintillators. The plastics are produced through the addition of selected quench agents to NE111 plastic scintillator that result in reduced total light output. Eight different agents have been studied. Benzophenone and piperidine are two of the most effective quench agents. Data are presented both for short and long decay components. The plastics are expected to make significant contributions in areas of plasma diagnostics

  9. Sub-nanosecond plastic scintillators

    International Nuclear Information System (INIS)

    Lyons, P.B.; Caldwell, S.E.; Hocker, L.P.; Crandall, D.G.; Zagarino, P.A.; Cheng, J.; Tirsell, G.; Hurlbut, C.R.

    1976-01-01

    Quenched plastic scintillators have been developed that yield much faster short decay components and greatly reduced long decay components compared to conventional plastic scintillators. The plastics are produced through the addition of selected quench agents to NE111 plastic scintillator that result in reduced total light output. Eight different agents have been studied. Benzophenone and piperidine are two of the most effective quench agents. Data are presented both for short and long decay components. The plastics are expected to make significant contributions in areas of plasma diagnostics

  10. Inspection des pieces flexibles sans gabarit de conformation

    Science.gov (United States)

    Aidibe, Ali

    defined as giving a clear idea to the manufacturing industry about the situation of the parts on the flexibility scale. Subsequently, we propose a new fixtureless inspection method for compliant parts: the IDB-CTB " Inspection of Deformable Bodies by Curvature and Thompson-Biweight " method. This approach combines the Gaussian curvature estimation, one of the intrinsic properties of the surface which is invariant under isometric transformations, with an identification method based on the extreme value statistics ( Thompson-Biweight Test). The low percentage of error in defect areas and in profile deviations estimated reflects the effectiveness of our approach. In the third phase of this thesis, we propose a novel method that can be considered as complementary to the IDB-CTB approach. In addition to the profile deviations, we aim to detect the localization defects. We introduce two criteria that correspond to the specification of compliant parts: the conservation of the curvilinear distance and the minimization between two objects (Hausdorff Distance). We adapt and automate the Coherent Point Drift; a powerful non-rigid registration algorithm widely used in medical imagery and animation, for satisfying these two criteria. We obtain satisfying results by applying the third approach on a typical aerospace sheet metal. The conclusion of this thesis summarizes the scientific contributions through our work on the fixtureless inspection of compliant parts and the perspective related with it. In the appendix, we introduce a graphical user interface (GUI) created to handle the proposed approaches as well as the case studies bank developed in the training at Bombardier Aerospace Inc.

  11. Compensatory plasticity: time matters

    Directory of Open Access Journals (Sweden)

    Latifa eLazzouni

    2014-06-01

    Full Text Available Plasticity in the human and animal brain is the rule, the base for development, and the way to deal effectively with the environment for making the most efficient use of all the senses. When the brain is deprived of one sensory modality, plasticity becomes compensatory: the exception that invalidates the general loss hypothesis giving the opportunity of effective change. Sensory deprivation comes with massive alterations in brain structure and function, behavioural outcomes, and neural interactions. Blind individuals do as good as the sighted and even more, show superior abilities in auditory, tactile and olfactory processing. This behavioural enhancement is accompanied with changes in occipital cortex function, where visual areas at different levels become responsive to non-visual information. The intact senses are in general used more efficiently in the blind but are also used more exclusively. New findings are disentangling these two aspects of compensatory plasticity. What is due to visual deprivation and what is dependent on the extended use of spared modalities? The latter seems to contribute highly to compensatory changes in the congenitally blind. Short term deprivation through the use of blindfolds shows that cortical excitability of the visual cortex is likely to show rapid modulatory changes after few minutes of light deprivation and therefore changes are possible in adulthood. However, reorganization remains more pronounced in the congenitally blind. Cortico-cortical pathways between visual areas and the areas of preserved sensory modalities are inhibited in the presence of vision, but are unmasked after loss of vision or blindfolding as a mechanism likely to drive cross-modal information to the deafferented visual cortex. Plasticity in the blind is also accompanied with neurochemical and morphological changes; both intrinsic connectivity and functional coupling at rest are altered but are likewise dependent on different sensory

  12. Mesocycles in conserving plastics

    DEFF Research Database (Denmark)

    Shashoua, Yvonne

    2016-01-01

    driven by the need to balance the requirements for reversibility in conservation practices with the artist’s intent and significance. Developments within each of the three mesocycles from the 1990s to date are discussed in this article. Environmental science and toxicology of waste plastics offer a novel...... source of information about real time degradation in terrestrial and marine microenvironments that seems likely to contribute to the conservation of similar materials in contemporary artworks....

  13. Plastic footwear for leprosy.

    Science.gov (United States)

    Antia, N H

    1990-03-01

    The anaesthetic foot in leprosy poses the most major problem in the rehabilitation of its patients. Various attempts have been made to produce protective footwear such as the microcellular rubber-car-tyre sandals. Unfortunately these attempts have had little success on a large scale because of the inability to produce them in large numbers and the stigma attached to such unusual footwear. While such footwear may be superior to the 'tennis' shoe in protecting the foot from injury by the penetration of sharp objects, it fails to distribute the weight-bearing forces which is the major cause of plantar damage and ulceration in the anaesthetic foot. This can be achieved by providing rigidity to the sole, as demonstrated by the healing of ulcers in plaster of paris casts or the rigid wooden clog. A new type of moulded plastic footwear has been evolved in conjunction with the plastic footwear industry which provides footwear that can be mass produced at a low price and which overcomes the stigma of leprosy. Controlled rigidity is provided by the incorporation of a spring steel shank between the sponge insole and the hard wearing plastic sole. Trials have demonstrated both the acceptability of the footwear and its protective effects as well as its hard wearing properties.

  14. Plastic waste disposal apparatus

    Energy Technology Data Exchange (ETDEWEB)

    Kito, S

    1972-05-01

    A test plant plastic incinerator was constructed by the Takuma Boiler Manufacturing Co. for Sekisui Chemical Industries, and the use of a continuous feed spreader was found to be most effective for prevention of black smoke, and the use of a venturi scrubber proved to be effective for elimination of hydrogen chloride gas. The incinerator was designed for combustion of polyvinyl chloride exclusively, but it is also applicable for combustion of other plastics. When burning polyethylene, polypropylene, or polystyrene, (those plastics which do not produce toxic gases), the incinerator requires no scrubber for the combustion gas. The system may or may not have a pretreatment apparatus. For an incinerator with a pretreatment system, the flow chart comprises a pit, a supply crane, a vibration feeder, a metal eliminator, a rotation shredder, a continuous screw feeder with a quantitative supply hopper, a pretreatment chamber (300 C dry distillation), a quantitative supply hopper, and the incinerator. The incinerator is a flat non-grid type combustion chamber with an oil burner and many air nozzles. From the incinerator, ashes are sent by an ash conveyor to an ash bunker. The combustion gas goes to the boiler, and the water supplied the boiler water pump creates steam. The heat from the gas is sent back to the pretreatment system through a heat exchanger. The gas then goes to a venturi scrubber and goes out from a stack.

  15. Conceptual design for muon detectors using resistive plastic tubes. Final technical report

    International Nuclear Information System (INIS)

    Border, P.; Courant, H.; Heller, K.; Jones, A.; Lin, J.; Maxam, D.; Ruddick, K.

    1998-01-01

    Reliable low cost detectors which can be built in quantity require a simple design consisting of as few separate pieces as possible using inexpensive materials. For example, ordinary insulating plastics with good structural strength, such as polyethylene or polystyrene, have about 1/3 the cost of aluminum per unit weight. Since plastic is also about 1/3 the density of aluminum, the material cost for a drift tube would be reduced by an order of magnitude. This substitution of plastic for aluminum alone would save the muon system for the SDC more than $2M. Additional savings of greater magnitude can be expected since an entire drift tube, including a field shaping electrode structure, can be manufactured as a single piece by the technique of co-extrusion. A symmetric design with all walls far from the wire will also eliminate critical tolerances in the relative position of the electrodes with respect to the wire. Furthermore, module assembly and mounting costs will surely be reduced if the muon detectors were light weight and, as far as possible, had the same shape and size. With the 8 cm diameter plastic tube of the design, the electric drift field is nearly uniform as shown. This field is determined by a simple symmetric electrode structure, so that the necessary drift/position relationship can be achieved without precisely controlling the position of the electrode structure with respect to the wire. If the positioning of the electrode structure relative to the wire is not a critical dimension, the structural support for the tube need not be maintained to a high tolerance reducing the cost of the structure. Using a resistive plastic to shape the potential gives a simple electrode structure that will require a minimum number of electronic connections. The basic element of this design is the cylindrical plastic drift tube constructed from co-extruded plastics of different conductivity

  16. Observational Study Unveils the Extensive Presence of Hazardous Elements in Beached Plastics from Lake Geneva

    Directory of Open Access Journals (Sweden)

    Montserrat Filella

    2018-02-01

    Full Text Available Over 3,000 samples of plastic litter have been retrieved from 12 pebble beaches around the shores of Lake Geneva. The plastic stock consisted of identifiable objects of various size and color, including bottles, bottle tops, cotton buds, pens, toys, and straws, an heterogeneous assortment of fragments whose origin was either discernible or unknown, and pieces or blocks of expanded polymer (polystyrene or polyurethane foam. Analysis of 670 samples by portable x-ray fluorescence (XRF spectrometry revealed high concentrations of hazardous elements or compounds among many plastics. These included Cd, Hg, and Pb (with maximum concentrations of 6,760, 810, and 23,500 ppm, respectively as stabilizers in PVC-based materials and/or brightly-colored sulfide or chromate pigments in primary and secondary plastics, and Br (with a maximum concentration of 27,400 ppm as a proxy for brominated flame retardants (BFRs in both plastics and foams. The abundance of hazardous elements in beached plastics that have been restricted or banned reflect the age and residence time of the plastic stock in the lake, coupled with a relatively high length of shoreline to surface area of the system. The migratability of hazardous elements from the polymeric matrix is likely to determine their environmental impacts and is recommended as a future area of research.

  17. Residual Stress Analysis of Severe Plastic Deformed Materials using the Finite Element Method and the Neutron Diffraction Method

    International Nuclear Information System (INIS)

    Kang, Mi Hyun; Seong, Back Suck; Kim, Hyoung Seop

    2009-01-01

    Severe plastic deformation (SPD) is one of the most promising top-down techniques, moving towards industrialization to fabricate bulk ultrafine grain materials. The strain distribution and deformation behavior during the ECAP (equal channel angular pressing), influenced by tool angles, friction and material behavior, was studied through experimental and numerical analyses. The residual stress of work piece which was straight before ECAP produces many serious problems in the next processing e.g. input of the work piece for the next ECAP. The bent work piece needs additional straightening or surface polishing even if the amount of bending is small, and residual stress need to be released before service applications. Residual stress, particularly tensile residual stress can be a very important factor in affecting the reliability and integrity of working parts. The formation of tensile residual stress may result in initiation of fatigue cracks, stress corrosion cracking, or other types of fracture. Hence, residual stress and resulting bending need to be controlled during ECAP. Thus, in current study the bending behavior and the residual stress of the work piece in ECAP are analyzed through experimental and finite element analyses by considering the effects of material, geometric, and processing parameters individually. The stress states in the ECAP processed work piece were measured by the non-destructive way using neutron diffraction. Efforts were made to suggest the alternate routes to reduce the residual stress and bending of work piece in ECAP

  18. New perspectives in plastic biodegradation.

    Science.gov (United States)

    Sivan, Alex

    2011-06-01

    During the past 50 years new plastic materials, in various applications, have gradually replaced the traditional metal, wood, leather materials. Ironically, the most preferred property of plastics--durability--exerts also the major environmental threat. Recycling has practically failed to provide a safe solution for disposal of plastic waste (only 5% out of 1 trillion plastic bags, annually produced in the US alone, are being recycled). Since the most utilized plastic is polyethylene (PE; ca. 140 million tons/year), any reduction in the accumulation of PE waste alone would have a major impact on the overall reduction of the plastic waste in the environment. Since PE is considered to be practically inert, efforts were made to isolate unique microorganisms capable of utilizing synthetic polymers. Recent data showed that biodegradation of plastic waste with selected microbial strains became a viable solution. Copyright © 2011 Elsevier Ltd. All rights reserved.

  19. Performance of molded plastic scintillators

    International Nuclear Information System (INIS)

    Gen, N.S.; Leman, V.E.; Solomonov, V.M.

    1989-01-01

    The performance of molded plastic scintillators is studied. The plastic scintillators studied were formed by transfer molding and intrusion from a scintillation composition consisting of polystyrene and a standard system of luminescent additives: 2 mass % of paraterphenyl + 0.06 mass % 1,4-di-/2-[5-phenyloxazoyly]/benzene and a plasticizer. The combined effect of mechanical load and temperature was studied. The effect of radiation on molded plastic scintillators was studied using gamma radiation from a 60 Co source. The studies show that the main operating characteristics of molded plastic scintillators are on a par with those of polymerized plastic scintillators. At the same time, molded plastic scintillators are superior in thermal stability at temperatures below the glass transition temperature and with respect to their working temperature range

  20. Group typicality, group loyalty and cognitive development.

    Science.gov (United States)

    Patterson, Meagan M

    2014-09-01

    Over the course of childhood, children's thinking about social groups changes in a variety of ways. Developmental Subjective Group Dynamics (DSGD) theory emphasizes children's understanding of the importance of conforming to group norms. Abrams et al.'s study, which uses DSGD theory as a framework, demonstrates the social cognitive skills underlying young elementary school children's thinking about group norms. Future research on children's thinking about groups and group norms should explore additional elements of this topic, including aspects of typicality beyond loyalty. © 2014 The British Psychological Society.

  1. Modelling object typicality in description logics

    CSIR Research Space (South Africa)

    Britz, K

    2009-12-01

    Full Text Available in the context under consideration, than those lower down. For any given class C, we assume that all objects in the appli- cation domain that are in (the interpretation of) C are more typical of C than those not in C. This is a technical construction which... to be modular partial orders, i.e. reflexive, transitive, anti- symmetric relations such that, for all a, b, c in ∆I , if a and b are incomparable and a is strictly below c, then b is also strictly below c. Modular partial orders have the effect...

  2. Benchmark calculation programme concerning typical LMFBR structures

    International Nuclear Information System (INIS)

    Donea, J.; Ferrari, G.; Grossetie, J.C.; Terzaghi, A.

    1982-01-01

    This programme, which is part of a comprehensive activity aimed at resolving difficulties encountered in using design procedures based on ASME Code Case N-47, should allow to get confidence in computer codes which are supposed to provide a realistic prediction of the LMFBR component behaviour. The calculations started on static analysis of typical structures made of non linear materials stressed by cyclic loads. The fluid structure interaction analysis is also being considered. Reasons and details of the different benchmark calculations are described, results obtained are commented and future computational exercise indicated

  3. Typical skeletal changes due to metastasising neuroblastomas

    International Nuclear Information System (INIS)

    Eggerath, A.; Persigehl, M.; Mertens, R.; Technische Hochschule Aachen

    1983-01-01

    Compared with other solid tumours in childhood, neuroblastomas show a marked tendency to metastasise to the skeleton. The differentiation of these lesions from inflammatory and other malignant bone lesions in this age group is often difficult. The radiological findings in ten patients with metastasing and histologically confirmed neuroblastomas have been reviewed and the typical appearances in the skeleton are described. The most important features in the differential diagnosies are discussed and the significance of bone changes in the diagnosis of neuroblastoma have been evaluated. (orig.) [de

  4. Pyrolysis of plastic packaging waste: A comparison of plastic residuals from material recovery facilities with simulated plastic waste

    International Nuclear Information System (INIS)

    Adrados, A.; Marco, I. de; Caballero, B.M.; López, A.; Laresgoiti, M.F.; Torres, A.

    2012-01-01

    Highlights: ► Pyrolysis of plastic waste. ► Comparison of different samples: real waste, simulated and real waste + catalyst. ► Study of the effects of inorganic components in the pyrolysis products. - Abstract: Pyrolysis may be an alternative for the reclamation of rejected streams of waste from sorting plants where packing and packaging plastic waste is separated and classified. These rejected streams consist of many different materials (e.g., polyethylene (PE), polypropylene (PP), polystyrene (PS), polyvinyl chloride (PVC), polyethylene terephthalate (PET), acrylonitrile butadiene styrene (ABS), aluminum, tetra-brik, and film) for which an attempt at complete separation is not technically possible or economically viable, and they are typically sent to landfills or incinerators. For this study, a simulated plastic mixture and a real waste sample from a sorting plant were pyrolyzed using a non-stirred semi-batch reactor. Red mud, a byproduct of the aluminum industry, was used as a catalyst. Despite the fact that the samples had a similar volume of material, there were noteworthy differences in the pyrolysis yields. The real waste sample resulted, after pyrolysis, in higher gas and solid yields and consequently produced less liquid. There were also significant differences noted in the compositions of the compared pyrolysis products.

  5. The Typicality Ranking Task: A New Method to Derive Typicality Judgments from Children

    Science.gov (United States)

    Ameel, Eef; Storms, Gert

    2016-01-01

    An alternative method for deriving typicality judgments, applicable in young children that are not familiar with numerical values yet, is introduced, allowing researchers to study gradedness at younger ages in concept development. Contrary to the long tradition of using rating-based procedures to derive typicality judgments, we propose a method that is based on typicality ranking rather than rating, in which items are gradually sorted according to their typicality, and that requires a minimum of linguistic knowledge. The validity of the method is investigated and the method is compared to the traditional typicality rating measurement in a large empirical study with eight different semantic concepts. The results show that the typicality ranking task can be used to assess children’s category knowledge and to evaluate how this knowledge evolves over time. Contrary to earlier held assumptions in studies on typicality in young children, our results also show that preference is not so much a confounding variable to be avoided, but that both variables are often significantly correlated in older children and even in adults. PMID:27322371

  6. Sample diversity and premise typicality in inductive reasoning: evidence for developmental change.

    Science.gov (United States)

    Rhodes, Marjorie; Brickman, Daniel; Gelman, Susan A

    2008-08-01

    Evaluating whether a limited sample of evidence provides a good basis for induction is a critical cognitive task. We hypothesized that whereas adults evaluate the inductive strength of samples containing multiple pieces of evidence by attending to the relations among the exemplars (e.g., sample diversity), six-year-olds would attend to the degree to which each individual exemplar in a sample independently appears informative (e.g., premise typicality). To test these hypotheses, participants were asked to select between diverse and non-diverse samples to help them learn about basic-level animal categories. Across various between-subject conditions (N=133), we varied the typicality present in the diverse and non-diverse samples. We found that adults reliably selected to examine diverse over non-diverse samples, regardless of exemplar typicality, six-year-olds preferred to examine samples containing typical exemplars, regardless of sample diversity, and nine-year-olds were somewhat in the midst of this developmental transition.

  7. Investigation and recovery of unrecovered fuel pellets and cladding tube pieces

    International Nuclear Information System (INIS)

    Kobayashi, Keiji

    1980-01-01

    The total weight of the fuel pellets lost due to break was about 1206 g, and cladding tube pieces were about 217 g. Among these, the pellets of about 527 g and the cladding tube pieces of about 152 g were recovered when broken fuel rods were discovered. It is not desirable to leave these broken pieces as unrecovered in view of safety and the management of nuclear fuel materials. Kansai Electric Power Co., Inc., investigated the position and the amount of these pellets and cladding tube pieces for about a year, and recovered a part of them. The results were written in two reports. The objects of the investigation and recovery, and the method of recovery are explained. The UO 2 and zirconium recovered were 58.52 g and 369.58 g, respectively. The solid pellets were recovered from the reactor, fuel assemblies, a spent fuel pit and canals, and the content in sludge was recovered from other installations. The amounts of unrecovered pellets and cladding tube pieces in primary cooling water, coolant filters, sealing water filters, primary cooling pipes, waste resins and fuel assemblies were estimated. The problems concerning the recovery and estimation are pointed out. The results of estimating the amount of uranium in coolant filters and sealing water filters are useful to know the time of the occurrence of accident. (Kako, I.)

  8. Manufacturing and thermomechanical testing of actively cooled all beryllium high heat flux test pieces

    International Nuclear Information System (INIS)

    Vasiliev, N.N.; Sokolov, Yu.A.; Shatalov, G.E.

    1995-01-01

    One of the problems affiliated to ITER high heat flux elements development is a problem of interface of beryllium protection with heat sink routinely made of copper alloys. To get rid of this problem all beryllium elements could be used as heat receivers in places of enhanced thermal loads. In accordance with this objectives four beryllium test pieces of two types have been manufactured in open-quotes Institute of Berylliumclose quotes for succeeding thermomechanical testing. Two of them were manufactured in accordance with JET team design; they are round open-quotes hypervapotron typeclose quotes test pieces. Another two ones are rectangular test sections with a twisted tape installed inside of the circular channel. Preliminary stress-strain analysis have been performed for both type of the test pieces. Hypervapotrons have been shipped to JET where they were tested on JET test bed. Thermomechanical testing of pieces of the type of open-quotes swirl tape inside of tubeclose quotes have been performed on Kurchatov Institute test bed. Chosen beryllium grade properties, some details of manufacturing, results of preliminary stress-strain analysis and thermomechanical testing of the test pieces open-quotes swirl tape inside of tubeclose quotes type are given in this report

  9. The Arctic Ocean as a dead end for floating plastics in the North Atlantic branch of the Thermohaline Circulation

    KAUST Repository

    Cózar, Andrés

    2017-04-20

    The subtropical ocean gyres are recognized as great marine accummulation zones of floating plastic debris; however, the possibility of plastic accumulation at polar latitudes has been overlooked because of the lack of nearby pollution sources. In the present study, the Arctic Ocean was extensively sampled for floating plastic debris from the Tara Oceans circumpolar expedition. Although plastic debris was scarce or absent in most of the Arctic waters, it reached high concentrations (hundreds of thousands of pieces per square kilometer) in the northernmost and easternmost areas of the Greenland and Barents seas. The fragmentation and typology of the plastic suggested an abundant presence of aged debris that originated from distant sources. This hypothesis was corroborated by the relatively high ratios of marine surface plastic to local pollution sources. Surface circulation models and field data showed that the poleward branch of the Thermohaline Circulation transfers floating debris from the North Atlantic to the Greenland and Barents seas, which would be a dead end for this plastic conveyor belt. Given the limited surface transport of the plastic that accumulated here and the mechanisms acting for the downward transport, the seafloor beneath this Arctic sector is hypothesized as an important sink of plastic debris.

  10. From macro- to microplastics - Analysis of EU regulation along the life cycle of plastic bags.

    Science.gov (United States)

    Steensgaard, Ida M; Syberg, Kristian; Rist, Sinja; Hartmann, Nanna B; Boldrin, Alessio; Hansen, Steffen Foss

    2017-05-01

    Plastic pollution and its environmental effects has received global attention the recent years. However, limited attention has so far been directed towards how plastics are regulated in a life cycle perspective and how regulatory gaps can be addressed in order to limit and prevent environmental exposure and hazards of macro- and microplastics. In this paper, we map European regulation taking outset in the life cycle perspective of plastic carrier bags: from plastic bag production to when it enters the environment. Relevant regulatory frameworks, directives and authorities along the life cycle are identified and their role in regulation of plastics is discussed. Most important regulations were identified as: the EU chemical Regulation, the Packaging and Packaging Waste Directive including the amending Directive regarding regulation of the consumption of lightweight plastic carrier bags, the Waste Framework Directive and the Directive on the Landfill of Waste. The main gaps identified relate to lack of clear definitions of categories of polymers, unambitious recycling rates and lack of consideration of macro- and microplastics in key pieces of legislation. We recommend that polymers are categorized according to whether they are polymers with the same monomer constituents (homopolymers) or with different monomer constituents (copolymers) and that polymers are no longer exempt from registration and evaluation under REACH. Plastics should furthermore have the same high level of monitoring and reporting requirements as hazardous waste involving stricter requirements to labelling, recordkeeping, monitoring and control over the whole lifecycle. Finally, we recommend that more ambitious recycle and recovery targets are set across the EU. Regulation of the consumption of lightweight plastic carrier bags should also apply to heavyweight plastic carrier bags. Last, the Marine and Water Framework Directives should specifically address plastic waste affecting water quality

  11. Nonlinear Progressive Collapse Analysis Including Distributed Plasticity

    Directory of Open Access Journals (Sweden)

    Mohamed Osama Ahmed

    2016-01-01

    Full Text Available This paper demonstrates the effect of incorporating distributed plasticity in nonlinear analytical models used to assess the potential for progressive collapse of steel framed regular building structures. Emphasis on this paper is on the deformation response under the notionally removed column, in a typical Alternate Path (AP method. The AP method employed in this paper is based on the provisions of the Unified Facilities Criteria – Design of Buildings to Resist Progressive Collapse, developed and updated by the U.S. Department of Defense [1]. The AP method is often used for to assess the potential for progressive collapse of building structures that fall under Occupancy Category III or IV. A case study steel building is used to examine the effect of incorporating distributed plasticity, where moment frames were used on perimeter as well as the interior of the three dimensional structural system. It is concluded that the use of moment resisting frames within the structural system will enhance resistance to progressive collapse through ductile deformation response and that it is conserative to ignore the effects of distributed plasticity in determining peak displacement response under the notionally removed column.

  12. Rehabilitation of large maxillary defect with two-piece maxillary obturators

    Directory of Open Access Journals (Sweden)

    Kanchan P Dholam

    2015-01-01

    Full Text Available The insertion and removal of an obturator in large maxillary defects with or without trismus is difficult. Fabrication of a two-piece obturator in such cases overcomes this problem. This article describes rehabilitation of large maxillary defects with two piece maxillary obturator of three types. All these obturators have a maxillary plate and a bulb component, which are approximated together by various techniques namely, silicone cover, embedded magnets, and press studs. Prosthetic rehabilitation of large maxillary defects with two-piece obturators offers the possibility of adequate oral rehabilitation by fabricating light weight prosthesis, which is easy to use. The bulb covers the undercut areas of the defect enhancing the facial contour and retention. It facilitates easy examination of underlying tissues, recreation of the anatomic barrier between the oral and nasal cavities and restoration of the function and esthetics. Thus, it adds to the quality of life.

  13. Pigment dispersion and chronic intraocular pressure elevation after sulcus placement of 3-piece acrylic intraocular lens.

    Science.gov (United States)

    Almond, M Camille; Wu, Michael C; Chen, Philip P

    2009-12-01

    A 55-year-old man had phacoemulsification and implantation of a 3-piece acrylic intraocular lens (IOL) (AcrySof MA60AC) in the right eye. One month postoperatively, the intraocular pressure (IOP) was 48 mm Hg and peripheral transillumination defects were noted in the iris circumferentially, with the IOL optic edge visible as a silhouette. Gonioscopy showed dense pigmentation of the trabecular meshwork in the right eye, but in the left eye, only mild trabecular meshwork pigment was seen, along with a concave peripheral iris insertion. At 21 months, the right eye required 3 medications for IOP control. While pigment dispersion has been widely reported after placement of 1-piece acrylic IOLs in the ciliary sulcus, we conclude that in susceptible individuals with a concave peripheral iris insertion, pigment dispersion can occur with sulcus placement of a 3-piece acrylic model despite its thinner optic and angulated haptics.

  14. Plastics in the Marine Environment.

    Science.gov (United States)

    Law, Kara Lavender

    2017-01-03

    Plastics contamination in the marine environment was first reported nearly 50 years ago, less than two decades after the rise of commercial plastics production, when less than 50 million metric tons were produced per year. In 2014, global plastics production surpassed 300 million metric tons per year. Plastic debris has been detected worldwide in all major marine habitats, in sizes from microns to meters. In response, concerns about risks to marine wildlife upon exposure to the varied forms of plastic debris have increased, stimulating new research into the extent and consequences of plastics contamination in the marine environment. Here, I present a framework to evaluate the current understanding of the sources, distribution, fate, and impacts of marine plastics. Despite remaining knowledge gaps in mass budgeting and challenges in investigating ecological impacts, the increasing evidence of the ubiquity of plastics contamination in the marine environment, the continued rapid growth in plastics production, and the evidence-albeit limited-of demonstrated impacts to marine wildlife support immediate implementation of source-reducing measures to decrease the potential risks of plastics in the marine ecosystem.

  15. Plastics in the Marine Environment

    Science.gov (United States)

    Law, Kara Lavender

    2017-01-01

    Plastics contamination in the marine environment was first reported nearly 50 years ago, less than two decades after the rise of commercial plastics production, when less than 50 million metric tons were produced per year. In 2014, global plastics production surpassed 300 million metric tons per year. Plastic debris has been detected worldwide in all major marine habitats, in sizes from microns to meters. In response, concerns about risks to marine wildlife upon exposure to the varied forms of plastic debris have increased, stimulating new research into the extent and consequences of plastics contamination in the marine environment. Here, I present a framework to evaluate the current understanding of the sources, distribution, fate, and impacts of marine plastics. Despite remaining knowledge gaps in mass budgeting and challenges in investigating ecological impacts, the increasing evidence of the ubiquity of plastics contamination in the marine environment, the continued rapid growth in plastics production, and the evidence—albeit limited—of demonstrated impacts to marine wildlife support immediate implementation of source-reducing measures to decrease the potential risks of plastics in the marine ecosystem.

  16. Abiotic degradation of plastic films

    Science.gov (United States)

    Ángeles-López, Y. G.; Gutiérrez-Mayen, A. M.; Velasco-Pérez, M.; Beltrán-Villavicencio, M.; Vázquez-Morillas, A.; Cano-Blanco, M.

    2017-01-01

    Degradable plastics have been promoted as an option to mitigate the environmental impacts of plastic waste. However, there is no certainty about its degradability under different environmental conditions. The effect of accelerated weathering (AW), natural weathering (NW) and thermal oxidation (TO) on different plastics (high density polyethylene, HDPE; oxodegradable high density polyethylene, HDPE-oxo; compostable plastic, Ecovio ® metalized polypropylene, PP; and oxodegradable metalized polypropylene, PP-oxo) was studied. Plastics films were exposed to AW per 110 hours; to NW per 90 days; and to TO per 30 days. Plastic films exposed to AW and NW showed a general loss on mechanical properties. The highest reduction in elongation at break on AW occurred to HDPE-oxo (from 400.4% to 20.9%) and was higher than 90% for HDPE, HDPE-oxo, Ecovio ® and PP-oxo in NW. No substantial evidence of degradation was found on plastics exposed to TO. Oxo-plastics showed higher degradation rates than their conventional counterparts, and the compostable plastic was resistant to degradation in the studied abiotic conditions. This study shows that degradation of plastics in real life conditions will vary depending in both, their composition and the environment.

  17. Production of the Large-area Plastic Scintillator for Beta-ray Detection using Epoxy Resin

    International Nuclear Information System (INIS)

    Nam, Jong Soo; Choi, Yong Seok; Hong, Sang Bum; Seo, Bum Kyung; Moon, Jei Kwon; Choi, Jong Won

    2016-01-01

    In this study, we prepared a plastic scintillator whose manufacturing process is simple and can be freely shaped. A thin plate of the plastic scintillator was manufactured using epoxy resin as a polymer. The plastic scintillator was made by mixing epoxy resin and organic scintillators under various conditions. The optimal mixture ratio to prepare the plastic scintillator was derived from the above results. Using the derived results, we made the large-area plastic scintillator which can quickly measure the contamination site and evaluated characteristics of the large-area plastic scintillator in the laboratory. A thin plate of a plastic scintillator with a simple preparation process can be freely shaped using epoxy resin and organic scintillators such as PPO and POPOP. PPO emits scintillation of light in the ultraviolet range, and POPOP is a wave shifter for moving the wavelength responsible for the PMT. The mixture ratio of PPO and POPOP was determined using their emission spectra. The optimal weight percentage of PPO and POPOP in an organic scintillator was determined to be 0.2 wt%:0.01 wt%. Based on the above results, the large-area plastic scintillator of the window size of a typical pancake-type αβ surface contamination counter was prepared. We want to evaluate the characteristics of the large-area plastic scintillator. However, there were the difficulties in evaluating characteristics of the large-area plastic scintillator. The cross-sectional area of the large-area plastic scintillator is significantly different to PMT

  18. Production of the Large-area Plastic Scintillator for Beta-ray Detection using Epoxy Resin

    Energy Technology Data Exchange (ETDEWEB)

    Nam, Jong Soo; Choi, Yong Seok; Hong, Sang Bum; Seo, Bum Kyung; Moon, Jei Kwon; Choi, Jong Won [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2016-10-15

    In this study, we prepared a plastic scintillator whose manufacturing process is simple and can be freely shaped. A thin plate of the plastic scintillator was manufactured using epoxy resin as a polymer. The plastic scintillator was made by mixing epoxy resin and organic scintillators under various conditions. The optimal mixture ratio to prepare the plastic scintillator was derived from the above results. Using the derived results, we made the large-area plastic scintillator which can quickly measure the contamination site and evaluated characteristics of the large-area plastic scintillator in the laboratory. A thin plate of a plastic scintillator with a simple preparation process can be freely shaped using epoxy resin and organic scintillators such as PPO and POPOP. PPO emits scintillation of light in the ultraviolet range, and POPOP is a wave shifter for moving the wavelength responsible for the PMT. The mixture ratio of PPO and POPOP was determined using their emission spectra. The optimal weight percentage of PPO and POPOP in an organic scintillator was determined to be 0.2 wt%:0.01 wt%. Based on the above results, the large-area plastic scintillator of the window size of a typical pancake-type αβ surface contamination counter was prepared. We want to evaluate the characteristics of the large-area plastic scintillator. However, there were the difficulties in evaluating characteristics of the large-area plastic scintillator. The cross-sectional area of the large-area plastic scintillator is significantly different to PMT.

  19. Optimized design and structural mechanics of a single-piece composite helicopter driveshaft

    Science.gov (United States)

    Henry, Todd C.

    In rotorcraft driveline design, single-piece composite driveshafts have much potential for reducing driveline mass and complexity over multi-segmented metallic driveshafts. The singlepiece shaft concept is enabled by the relatively high fatigue strain capacity of fiber reinforced polymer composites over metals. Challenges for single-piece driveshaft design lie in addressing the self-heating behavior of the composite due to the material damping, as well as, whirling stability, torsional buckling stability, and composite strength. Increased composite temperature due to self-heating reduces the composite strength and is accounted for in this research. The laminate longitudinal stiffness ( Ex) and strength (Fx) are known to be heavily degraded by fiber undulation, however, both are not well understood in compression. The whirling stability (a function of longitudinal stiffness) and the composite strength are strongly influential in driveshaft optimization, and thus are investigated further through the testing of flat and filament wound composite specimens. The design of single-piece composite driveshafts, however, needs to consider many failure criteria, including hysteresis-induced overheating, whirl stability, torsional buckling stability, and material failure by overstress. The present investigation uses multi-objective optimization to investigate the design space which visually highlights design trades. Design variables included stacking sequence, number of laminas, and number of hanger bearings. The design goals were to minimize weight and maximize the lowest factor of safety by adaptively generating solutions to the multi-objective problem. Several design spaces were investigated by examining the effect of misalignment, ambient temperature, and constant power transmission on the optimized solution. Several materials of interest were modeled using experimentally determined elastic properties and novel temperature-dependent composite strength. Compared to the

  20. Review of Agricultural Plastic Mulching and Its Residual Pollution and Prevention Measures In China

    Directory of Open Access Journals (Sweden)

    YAN Chang-rong

    2014-04-01

    Full Text Available Agricultural plastic film mulching is one of important technologies, but the plastic film pollution has been a serious issue for agri-cultural sustainable development in China. System analysis of this technique and its residue pollution and control ways have vital practicalsignificance for rational application of agricultural plastil film. In this paper, on the basis of our previous work,agricultural plastic filmmulching, its residue pollution and control technologies were concluded. Some important conclusions were found that, the amount of plasticfilm and mulching area had kept increasing with annual increasing rate about 8% since the 80s of the 20th century. From 1991 to 2011, thedensity of plastic film utilized increased 3-10 times, but it has very sharply different spatial pattern in different province. In general, the northand west China has high value, and the increase rate is also huge in the past 20 years. The crops of utilized mulching plastic film have extendedfrom cash crops to grain crops, and the order of crop area is followed by maize, vegetable, cotton, tobacco and peanut. The main functions ofmulching plastic film are keeping soil moisture and increasing soil temperature, against weeds and insect. At the same time, its side effectsappear with continuous utilization. The main problems are residues left in soil to destroy soil structure, impress soil permeability, impede seedgermination as well as water and nutrients uptaking, and block crop root system development. It has very serious pollution for the field utilizedplastic mulching film for long term. The residual amount in soil is about 71.9-259.1 kg·hm-2, and has sharply spatial difference. The residualamount in soil. In Northwest China, is more serious than that in North China and Southwest China. Because of difference of tillage and appli-canon ways, there are great differences on the area and shape of the plastic film piece left in soil. The main types of shapes are flaky

  1. Pieces of Other Worlds - Enhance YSS Education and Public Outreach Events with Extraterrestrial Samples

    Science.gov (United States)

    Allen, C.

    2010-12-01

    During the Year of the Solar System spacecraft will encounter two comets; orbit the asteroid Vesta, continue to explore Mars with rovers, and launch robotic explorers to the Moon and Mars. We have pieces of all these worlds in our laboratories. Extensive information about these unique materials, as well as actual lunar samples and meteorites, is available for display and education. The Johnson Space Center (JSC) curates NASA's extraterrestrial samples to support research, education, and public outreach. At the current time JSC curates five types of extraterrestrial samples: Moon rocks and soils collected by the Apollo astronauts Meteorites collected on US expeditions to Antarctica (including rocks from the Moon, Mars, and many asteroids including Vesta) “Cosmic dust” (asteroid and comet particles) collected by high-altitude aircraft Solar wind atoms collected by the Genesis spacecraft Comet and interstellar dust particles collected by the Stardust spacecraft These rocks, soils, dust particles, and atoms continue to be studied intensively by scientists around the world. Descriptions of the samples, research results, thousands of photographs, and information on how to request research samples are on the JSC Curation website: http://curator.jsc.nasa.gov/ NASA is eager for scientists and the public to have access to these exciting samples through our various loan procedures. NASA provides a limited number of Moon rock samples for either short-term or long-term displays at museums, planetariums, expositions, and professional events that are open to the public. The JSC Public Affairs Office handles requests for such display samples. Requestors should apply in writing to Mr. Louis Parker, JSC Exhibits Manager. He will advise successful applicants regarding provisions for receipt, display, and return of the samples. All loans will be preceded by a signed loan agreement executed between NASA and the requestor's organization. Email address: louis.a.parker@nasa.gov Sets

  2. Device for inspecting pieces of luggage by means of X-rays

    International Nuclear Information System (INIS)

    Kunze, C.; Dennhoven, M.

    1977-01-01

    Luggage inspection facility using X-rays, the piece of luggage appearing as a shadow image on a luminous screen. The shielded casing contains a control compartment holding the piece of luggage. During radioscopy the control compartment is closed by means of a shielding tunnel. As during mechanism for the shielding tunnel there is used a so-called linear motor with a moving magnetic field, operating a bar connected with the shielding tunnel through a flexible coupling. The motor is turned off in its terminal positions by means of a magnet and protective gas contacts. (HP) 891 HP [de

  3. A study for the improvement of top end piece structure strength

    International Nuclear Information System (INIS)

    Song, Kee Nam; Sohn, Dong Seong

    1989-01-01

    As a part of the top end piece(TEP) for the 14 X 14 reload fuel, various models of top end piece structure were analysed, using the ANSYS code, under fuel assembly shipping and handling load conditions. The 3-dimensional isoparametric elements were used in each model. By rearrangement of slots and holes on the adapter plate, without violating the design requirements, and also by changing the enclosure attachment method used on the adapter plate from pin joints to through-weld, the load carrying capacity of the adapter plate was greatly strengthened. These concepts were adopted for the design of the 14 X 14 reload fuel. (Author)

  4. Sutureless, Glueless, Scleral Fixation of Single-Piece and Toric Intraocular Lens: A Novel Technique

    Directory of Open Access Journals (Sweden)

    Aditya Kelkar

    2015-07-01

    Full Text Available Sutureless, glueless, scleral fixation of an intraocular lens is a known technique of fixing a lens in the scleral pockets. However, this technique is applied to single-piece and toric lenses instead of 3-piece lenses, allowing the advantage of the use of premium lenses in patients with poor capsular support. Favourable results without complications of pigment dispersion, iris transillumination defects, dysphotopsia, elevated intraocular pressure, intraocular hemorrhage and cystoid macular edema with a well-centered, stable intraocular lens have been observed in the 3-month postoperative period in both cases.

  5. Plastics pipe couplings

    International Nuclear Information System (INIS)

    Glover, J.B.

    1980-07-01

    A method is described of making a pipe coupling of the type comprising a plastics socket and a resilient annular sealing member secured in the mouth thereof, in which the material of at least one component of the coupling is subjected to irradiation with high energy radiation whereby the material is caused to undergo cross-linking. As examples, the coupling may comprise a polyethylene or plasticised PVC socket the material of which is subjected to irradiation, and the sealing member may be moulded from a thermoplastic elastomer which is subjected to irradiation. (U.K.)

  6. Low-cost rapid prototyping of flexible plastic paper based microfluidic devices

    KAUST Repository

    Fan, Yiqiang

    2013-04-01

    This research presents a novel rapid prototyping method for paper-based flexible microfluidic devices. The microchannels were fabricated using laser ablation on a piece of plastic paper (permanent paper), the dimensions of the microchannels was carefully studied for various laser powers and scanning speeds. After laser ablation of the microchannels on the plastic paper, a transparent poly (methyl methacrylate)(PMMA) film was thermally bonded to the plastic paper to enclose the channels. After connection of tubing, the device was ready to use. An example microfluidic device (droplet generator) was also fabricated using this technique. Due to the flexibility of the fabricated device, this technique can be used to fabricate 3D microfluidic devices. The fabrication process was simple and rapid without any requirement of cleanroom facilities. © 2013 IEEE.

  7. Plastic pollutants in water environment

    Directory of Open Access Journals (Sweden)

    Mrowiec Bożena

    2017-12-01

    Full Text Available Nowadays, wide applications of plastics result in plastic waste being present in the water environment in a wide variety of sizes. Plastic wastes are in water mainly as microplastics (the size range of 1 nm to < 5 mm. Microplastics have been recognized as an emerging threat, as well as ecotoxicological and ecological risk for water ecosystems. In this review are presented some of the physicochemical properties of plastic materials that determine their toxic effect on the aquatic environment. Wastewater treatment plants (WWTPs are mentioned as one of main sources of microplastics introduced into fresh water, and rivers are the pathways for the transportation of the pollutants to seas and oceans. But, effluents from tertiary wastewater treatment facilities can contain only minimally microplastic loads. The issue of discharge reduction of plastic pollutants into water environment needs activities in the scope of efficient wastewater treatment, waste disposal, recycling of plastic materials, education and public involvement.

  8. Plastic food packaging and health

    Directory of Open Access Journals (Sweden)

    Raika Durusoy

    2011-02-01

    Full Text Available Plastics have a wide usage in our daily lives. One of their uses is for food packaging and food containers. The aim of this review is to introduce different types of chemicals that can leach from food packaging plastics into foods and cause human exposure and to mention their effects on health. The types of plastics were reviewed under the 13 headings in Turkish Codex Alimentarius and plastics recycling symbols were provided to enable the recognition of the type of plastic when applicable. Chemicals used during the production and that can cause health risks are investigated under the heading of the relevant type of plastic. The most important chemicals from plastic food packaging that can cause toxicity are styrene, 1,3-butadiene, melamine, formaldehyde, acrylamide, di-2-ethylhexyl phthalate, di-2-ethylhexyl adipate, vinyl chloride and bisphenol A. These chemicals have endocrine disrupting, carcinogenic and/or development disrupting effects. These chemicals may leach into foods depending on the chemical properties of the plastic or food, temperature during packaging, processing and storage, exposure to UV and duration of storage. Contact with fatty/oily or acidic foods, heating of the food inside the container, or drinking hot drinks from plastic cups, use of old and scratched plastics and some detergents increase the risk of leaching. The use of plastic containers and packaging for food and beveradges should be avoided whenever possible and when necessary, less harmful types of plastic should be preferred. [TAF Prev Med Bull 2011; 10(1.000: 87-96

  9. New polyvinylchloride plasticizers

    Directory of Open Access Journals (Sweden)

    MAZITOVA Aliya Karamovna

    2017-11-01

    Full Text Available One of the main large-capacity polymers of modern chemical industry is polyvinylchloride (PVC. Polyvinylchloride is characterized by many useful engineering properties – chemical firmness in different environments, good electric properties, etc. It explains immensely various use of materials on the basis of PVC in different engineering industries. It is cable, building, light industries, mechanical engineering and automotive industry where PVC is widely applied. One of the reasons why PVC production is dramatically growing is that there is no yet other polymer which could be subjected to such various modifying as it is done with PVC. However under normal temperature this polymer is fragile and isn't elastic that limits the field of its application. Rapid growth of production of polyvinylchloride is explained by its ability to modify properties, due to introduction of special additives when processing. Introduction of plasticizers – mostlly esters of organic and inorganic acids – into PVC allows significant changing properties of polymer. Plasticizers facilitate process of receiving polymeric composition, increase flexibility and elasticity of the final polymeric product due to internal modification of polymeric molecule.

  10. ONE TYPICAL EXTREMUM IN ELECTRICAL PROBLEMS

    Directory of Open Access Journals (Sweden)

    V. I. Goroshko

    2014-01-01

    Full Text Available The aim of this work is to attract attention of teachers, scientific personnel, engineers and students to one peculiarity of extremum seeking in different electrical problems. This feature lies in the fact that in many parts of electrical engineering extremum seeking comes to analysis one and the same mathematical structure (T-structure, but differences lie only in many symbols (designation.In one problems this structure appear in finale, the most simple form, but in others – T-structure is “veiled”, and as a rule  we need  elementary algebraic transformation to detect it.Taking into account high frequency of this structure appearing in electrical problems, in the first part of article the authors  carried out the investigation of extremum characteristics of T-structure and show the results in easy algorithms. To determine the typical T-structure there were taken five problems-examples for extremum seeking  from different parts of electrical engineering. The first and the second examples belong to the theory of electrical circuits.In the first example the problem of maximum active load power obtaining was considered, in the second we see the solution of problem for inductive coupled circuit adjustment in order to obtain the hump current. In the third example the band active filter, built on operating amplifier, is analyzed. According to these methods, taken in the first part of article, the frequency is determined, on which amplifier provides maximum  amplification factor. The forth example deals with analysis of efficiency of transformer. According to algorithm, the optimal efficiency of transformer’s load and also equation for its maximum was determined in this article. In the fifth example the mechanical characteristics of induction motor is analyzed. It is indicated how, on the basis of algorithms article, to obtain equations for critical slip and motor moment, and also the simple development of formula Klossa.The methods of

  11. Americium behaviour in plastic vessels

    International Nuclear Information System (INIS)

    Legarda, F.; Herranz, M.; Idoeta, R.; Abelairas, A.

    2010-01-01

    The adsorption of 241 Am dissolved in water in different plastic storage vessels was determined. Three different plastics were investigated with natural and distilled waters and the retention of 241 Am by these plastics was studied. The same was done by varying vessel agitation time, vessel agitation speed, surface/volume ratio of water in the vessels and water pH. Adsorptions were measured to be between 0% and 70%. The adsorption of 241 Am is minimized with no water agitation, with PET or PVC plastics, and by water acidification.

  12. Americium behaviour in plastic vessels

    Energy Technology Data Exchange (ETDEWEB)

    Legarda, F.; Herranz, M. [Departamento de Ingenieria Nuclear y Mecanica de Fluidos, Escuela Tecnica Superior de Ingenieria de Bilbao, Universidad del Pais Vasco (UPV/EHU), Alameda de Urquijo s/n, 48013 Bilbao (Spain); Idoeta, R., E-mail: raquel.idoeta@ehu.e [Departamento de Ingenieria Nuclear y Mecanica de Fluidos, Escuela Tecnica Superior de Ingenieria de Bilbao, Universidad del Pais Vasco (UPV/EHU), Alameda de Urquijo s/n, 48013 Bilbao (Spain); Abelairas, A. [Departamento de Ingenieria Nuclear y Mecanica de Fluidos, Escuela Tecnica Superior de Ingenieria de Bilbao, Universidad del Pais Vasco (UPV/EHU), Alameda de Urquijo s/n, 48013 Bilbao (Spain)

    2010-07-15

    The adsorption of {sup 241}Am dissolved in water in different plastic storage vessels was determined. Three different plastics were investigated with natural and distilled waters and the retention of {sup 241}Am by these plastics was studied. The same was done by varying vessel agitation time, vessel agitation speed, surface/volume ratio of water in the vessels and water pH. Adsorptions were measured to be between 0% and 70%. The adsorption of {sup 241}Am is minimized with no water agitation, with PET or PVC plastics, and by water acidification.

  13. Americium behaviour in plastic vessels.

    Science.gov (United States)

    Legarda, F; Herranz, M; Idoeta, R; Abelairas, A

    2010-01-01

    The adsorption of (241)Am dissolved in water in different plastic storage vessels was determined. Three different plastics were investigated with natural and distilled waters and the retention of (241)Am by these plastics was studied. The same was done by varying vessel agitation time, vessel agitation speed, surface/volume ratio of water in the vessels and water pH. Adsorptions were measured to be between 0% and 70%. The adsorption of (241)Am is minimized with no water agitation, with PET or PVC plastics, and by water acidification. Copyright 2009 Elsevier Ltd. All rights reserved.

  14. Typical and atypical presentations of aspergilloma

    International Nuclear Information System (INIS)

    Villajos, M.; Darnell, A.; Gallardo, X.; Castaner, E.; Mata, J. M.; Paedavila, E.

    1999-01-01

    To show the different forms of radiological presentations of aspergilloma, emphasizing the importance of recognizing the atypical forms. The explorations of 11 patients with aspergilloma were examined retrospectively between 1993 and 1997. These patients were studied using conventional X-rays and computed tomography (CT): Typical and atypical radiological findings were observed. In two patients, who presented recurrent hemoptysis, a percutaneous installation of amphotericin B was carried out with tomographic control. Out of the 11 patients, two were female and nine male. In eight of the cases the radiological findings showed an intercavity injury with different evolutionary forms, while in three of the cases there was a progressive pleural swelling. In the two patients treated pertinaciously, no significant radiological changes were observed, however, neither of them showed hemoptysis again. The pleural swelling adjacent to the cavity and/or the swelling of the cavity wall are atypical radiological presentations of the aspergilloma, that can accompany or precede the appearance of this illness. (Author) 7 refs

  15. Idiopathic intracranial hypertension: A typical presentation

    International Nuclear Information System (INIS)

    Algahtani, Hussein A.; Obeid, Tahir H.; Abuzinadah, Ahmad R.; Baeesa, Saleh S.

    2007-01-01

    Objective was to describe the clinical features of 5 patients with rare atypical presentation of idiopathic intracranial hypertension (IIH), and propose the possible mechanism of this atypical presentation. We carried out a retrospective study of 5 patients, admitted at King Khalid National Guard Hospital, Jeddah, Kingdom of Saudi Arabia with IIH during the period from January 2001 to December 2005. All were females with their age ranges from 24 to 40 years. The clinical presentations, the laboratory and imaging studies were analyzed. The opening pressures of the lumbar puncture tests were documented. All patients were presented with headache. One had typical pain of trigeminal neuralgia and one with neck pain and radiculopathy. Facial diplegia was present in one patient and two patients had bilateral 6th cranial neuropathy. Papilledema was present in all patients except in one patient. Imaging study was normal in all patients, and they had a very high opening pressure during lumbar puncture, except in one patient. All patients achieved full recovery with medical therapy in 6 to 12 weeks with no relapse during the mean follow up of 2 years. Atypical finding in IIH are rare and require a high index of suspicion for early diagnosis. (author)

  16. Effects of mechanical and chemical processes on the degradation of plastic beach debris on the island of Kauai, Hawaii

    International Nuclear Information System (INIS)

    Cooper, David A; Corcoran, Patricia L

    2010-01-01

    Plastic debris is accumulating on the beaches of Kauai at an alarming rate, averaging 484 pieces/day in one locality. Particles sampled were analyzed to determine the effects of mechanical and chemical processes on the breakdown of polymers in a subtropical setting. Scanning electron microscopy (SEM) indicates that plastic surfaces contain fractures, horizontal notches, flakes, pits, grooves, and vermiculate textures. The mechanically produced textures provide ideal loci for chemical weathering to occur which further weakens the polymer surface leading to embrittlement. Fourier transform infrared spectroscopy (FTIR) results show that some particles have highly oxidized surfaces as indicated by intense peaks in the lower wavenumber region of the spectra. Our textural analyses suggest that polyethylene has the potential to degrade more readily than polypropylene. Further evaluation of plastic degradation in the natural environment may lead to a shift away from the production and use of plastic materials with longer residence times.

  17. Think Piece

    African Journals Online (AJOL)

    Environmental problems have reached unprecedented levels to the extent that it would be ..... indigenous peoples' ways of being–knowing, where ethics involves a .... Wals (2015:502) conclude that the DESD has been 'business as usual' as far as challenging .... Ubuntu, ukama, environment and moral education. Journal ...

  18. think Piece

    African Journals Online (AJOL)

    As indicated in the 2010 United Nations Educational, Scientific and Cultural .... The rise of corporate universities, where universities seek to provide only those skills that are ..... doctoral thesis, Rhodes University, Grahamstown, South Africa.

  19. Pieces Urbaines

    DEFF Research Database (Denmark)

    Skousbøll, Karin

    Parallelt med de store franske præstigeprojekter har en anden bybygningsstrategi udviklet sig, hvor man ser byens dynamik og naturlige fragmentering som et positivt alternativ til de absolutte helhedsplaner - en "Peices Urbaines"-metodik: Visionerne for en helhed kombineres med en fleksibilitet o...

  20. think piece

    African Journals Online (AJOL)

    , ... Hence we shall continue to have a worsening ecological crisis until .... When it comes to economic development, we have been neglecting the impact of .... similar to the 'ordination of trees' often done in Thailand by Buddhist Monks. In Thai ...

  1. Ear Pieces

    Science.gov (United States)

    DiJulio, Betsy

    2011-01-01

    In this article, the author describes an art project wherein students make fanciful connections between art and medicine. This project challenges students to interpret "ear idioms" (e.g. "blow it out your ear," "in one ear and out the other") by relying almost entirely on realistic ear drawings, the placement of them, marks, and values. In that…

  2. Think Piece

    African Journals Online (AJOL)

    consuming his children, taking away their future before they can live it. .... Fifthly, only once all of this is secured can we look forward to some leisure ... This argument made sense in a late 19th century Anglo-American dominated, liberal-.

  3. think Piece

    African Journals Online (AJOL)

    related to the hegemony of positivism, and demand a transgressive move towards .... perhaps gay men do in fact need special attention given their higher rates of .... Participatory action research methodologies are a reaction against positivist ...

  4. Think Piece

    African Journals Online (AJOL)

    It scopes an ESD terrain where knowledge and ethics-led learning .... and ontological attributes that are important for a grasp of the problem in context. ..... learning programme (ESD) as a transgressive space within and around better situated ...

  5. Debris filtering effectiveness and pressure drop tests of debris resistance-bottom end piece

    International Nuclear Information System (INIS)

    Chung, Moon Ki; Song, Chul Hwa; Chung, Heung June; Won, Soon Yeun; Cho, Young Ro; Kim, Bok Deuk

    1992-03-01

    In this final report, described are the test conditions and test procedures for the debris filtering effectiveness and pressure drop tests for developing the Debris Resistance-Bottom End Piece (DR-BEP). And the test results are tabulated for later evaluation. (Author)

  6. Parameter study of temperature distribution in a work-piece during dry hyperbaric GTA-welding

    International Nuclear Information System (INIS)

    Fulfs, H.

    1989-01-01

    In a sensitivity study the influence of initial and boundary welding parameters upon the spatial and temporal temperature distribution in a work-piece during dry hyperbaric GTA-welding is investigated. It will be shown that at constant arc current a variation of pressure (1-60 bar), arc length (3-10 mm), welding speed (1-2.5 mm/s) or the initial temperature (20-200deg C) of the work-piece to some extend significantly influences the size of melt and heat affected zone as well as the maximum temperature and cooling behaviour of the work-piece; compared to this no mentionable effects of shielding gas temperature (20-300deg C) or flow rate (10-500 dm N 3 /min) on the thermal condition of the work-piece can be recognized. The discovered relationships have been approximated by simple correlations, which can be used for parameter optimization and process control. (orig.) With 33 figs., 4 tabs [de

  7. Comparison of the T-piece resuscitator with other neonatal manual ventilation devices: A qualitative review.

    LENUS (Irish Health Repository)

    2012-01-31

    AIM: To review the literature surrounding various aspects of T-piece resuscitator use, with particular emphasis on the evidence comparing the device to other manual ventilation devices in neonatal resuscitation. DATA SOURCES: The Medline, EMBASE, Cochrane databases were searched in April 2011. Ongoing trials were identified using www.clinicaltrials.gov and www.controlled-trials.com. Additional studies from reference lists of eligible articles were considered. All studies including T-piece resuscitator use were eligible for inclusion. RESULTS: Thirty studies were included. There were two randomised controlled trials in newborn infants comparing the devices, one of which addressed short and intermediate term morbidity and mortality outcomes and found no difference between the T-piece resuscitator and self inflating bag. From manikin studies, advantages to the T-piece resuscitator include the delivery of inflating pressures closer to predetermined target pressures with least variation, the ability to provide prolonged inflation breaths and more consistent tidal volumes. Disadvantages include a technically more difficult setup, more time required to adjust pressures during resuscitation, a larger mask leak and less ability to detect changes in compliance. CONCLUSIONS: There is a need for appropriately designed randomised controlled trials in neonates to highlight the efficacy of one device over another. Until these are performed, healthcare providers should be appropriately trained in the use of the device available in their departments, and be aware of its own limitations.

  8. The Ayre's T-piece turns 80: A 21st century review.

    Science.gov (United States)

    Oswald, Lauren; Smith, Emma-Jane; Mathew, Malcolm; Goonasekera, Chulananda

    2018-06-07

    Ayre's T-piece, first introduced 80 years ago, continues to be widely used in pediatric anesthesia despite colossal advances in equipment and technology. We present a review of its history, advantages, and disadvantages, and place in modern-day clinical practice. © 2018 John Wiley & Sons Ltd.

  9. Apparatus of irradiation of steel test pieces in the Marcoule pile G 1

    International Nuclear Information System (INIS)

    Marinot, R.; Wallet, Ph.

    1960-01-01

    Test pieces of steel were irradiated in the reactor G1 at Marcoule, in convectors replacing fuel elements, and in vertical channels in furnace-heated containers. The apparatus designed for this irradiation is described: containers, converter-rods, suspension fixtures and clamps, temperature measurement devices, lead castles and unloading set-ups. (author) [fr

  10. Dramatherapy and Family Therapy in Education: Essential Pieces of the Multi-Agency Jigsaw

    Science.gov (United States)

    McFarlane, Penny; Harvey, Jenny

    2012-01-01

    A collaborative therapeutic approach often proves the best way to assess and meet the needs of children experiencing barriers to learning. This book gives a concise overview of drama and family therapy and describes how both therapies can work together to provide essential pieces of the jigsaw of emotional support for troubled children within an…

  11. Joining the Pieces: Using Concept Maps for Integrated Learning and Assessment in an Introductory Management Course

    Science.gov (United States)

    Connolly, Heather; Spiller, Dorothy

    2016-01-01

    This paper reports on and evaluates the use of concept mapping as a learning tool in a large first year Management course. The goal was to help students make personal sense of course learning and to build their understanding of links and relationships between key course ideas. Concept mapping was used for three summative assessment pieces,…

  12. Ultrasonic non-destructive testing of pieces of complex geometry with a flexible phased array transducer

    Science.gov (United States)

    Chatillon; Cattiaux; Serre; Roy

    2000-03-01

    Ultrasonic non-destructive testing of components of complex geometry in the nuclear industry faces several difficulties: sensitivity variations due to unmatched contact, inaccurate localization of defects due to variations of transducer orientation, and uncovered area of the component. To improve the performances of such testing and defect characterization, we propose a new concept of ultrasonic contact phased array transducer. The phased array transducer has a flexible radiating surface able to fit the actual surface of the piece to optimize the contact and thus the sensitivity of the test. To control the transmitted field, and therefore to improve the defect characterization, a delay law optimizing algorithm is developed. To assess the capability of such a transducer, the Champ-Sons model, developed at the French Atomic Energy Commission for predicting field radiated by arbitrary transducers into pieces, has to be extended to sources directly in contact with pieces of complex geometry. The good behavior of this new type of probe predicted by computations is experimentally validated with a jointed transducer positioned on pieces of various profiles.

  13. Study of Using Excess Stock to Reduce Naval Aviation Depot-Level Repairable Piece Part Backorders

    Science.gov (United States)

    2016-12-01

    used to develop and run the comparison of the backorders and excess stock records. Python is chosen because of its ease of learning and use...sustainable source of bit-piece parts for future requisitions. 14. SUBJECT TERMS naval aviation AVDLRs, backorder, excess, DLA, WSS, FRC, Python ...SCHOOL December 2016 Approved by: Geraldo Ferrer Eddine Dahel Peter Ward Bryan Hudgens Academic Associate

  14. Ways of Knowing and Types of Knowledge: How Do Students Approach a New Piece of Music?

    Science.gov (United States)

    dos Santos, Regina Antunes Teixeira; Gerling, Cristina Capparelli

    2012-01-01

    In an exploratory study lasting more than 16 weeks, 15 undergraduate and graduate piano students prepared a short piece by the Brazilian composer Guarnieri, "Ponteio" no. 22, without guidance from their piano teachers. The data that were collected included their performances, interviews pertaining to their practice and stimulated recall…

  15. Threat of plastic pollution to seabirds is global, pervasive, and increasing

    Science.gov (United States)

    Wilcox, Chris; Van Sebille, Erik; Hardesty, Britta Denise

    2015-01-01

    Plastic pollution in the ocean is a global concern; concentrations reach 580,000 pieces per km2 and production is increasing exponentially. Although a large number of empirical studies provide emerging evidence of impacts to wildlife, there has been little systematic assessment of risk. We performed a spatial risk analysis using predicted debris distributions and ranges for 186 seabird species to model debris exposure. We adjusted the model using published data on plastic ingestion by seabirds. Eighty of 135 (59%) species with studies reported in the literature between 1962 and 2012 had ingested plastic, and, within those studies, on average 29% of individuals had plastic in their gut. Standardizing the data for time and species, we estimate the ingestion rate would reach 90% of individuals if these studies were conducted today. Using these results from the literature, we tuned our risk model and were able to capture 71% of the variation in plastic ingestion based on a model including exposure, time, study method, and body size. We used this tuned model to predict risk across seabird species at the global scale. The highest area of expected impact occurs at the Southern Ocean boundary in the Tasman Sea between Australia and New Zealand, which contrasts with previous work identifying this area as having low anthropogenic pressures and concentrations of marine debris. We predict that plastics ingestion is increasing in seabirds, that it will reach 99% of all species by 2050, and that effective waste management can reduce this threat. PMID:26324886

  16. Threat of plastic pollution to seabirds is global, pervasive, and increasing.

    Science.gov (United States)

    Wilcox, Chris; Van Sebille, Erik; Hardesty, Britta Denise

    2015-09-22

    Plastic pollution in the ocean is a global concern; concentrations reach 580,000 pieces per km(2) and production is increasing exponentially. Although a large number of empirical studies provide emerging evidence of impacts to wildlife, there has been little systematic assessment of risk. We performed a spatial risk analysis using predicted debris distributions and ranges for 186 seabird species to model debris exposure. We adjusted the model using published data on plastic ingestion by seabirds. Eighty of 135 (59%) species with studies reported in the literature between 1962 and 2012 had ingested plastic, and, within those studies, on average 29% of individuals had plastic in their gut. Standardizing the data for time and species, we estimate the ingestion rate would reach 90% of individuals if these studies were conducted today. Using these results from the literature, we tuned our risk model and were able to capture 71% of the variation in plastic ingestion based on a model including exposure, time, study method, and body size. We used this tuned model to predict risk across seabird species at the global scale. The highest area of expected impact occurs at the Southern Ocean boundary in the Tasman Sea between Australia and New Zealand, which contrasts with previous work identifying this area as having low anthropogenic pressures and concentrations of marine debris. We predict that plastics ingestion is increasing in seabirds, that it will reach 99% of all species by 2050, and that effective waste management can reduce this threat.

  17. Preliminary investigation of the transport of small plastic litter along a vegetated riverbank

    Science.gov (United States)

    Liu, Da; Valyrakis, Manousos

    2017-04-01

    Plastics are widely used in consumer products, due to its low cost, low weight and high durability compared to other types of materials. Contamination of marine ecosystems due to plastics (including microplastics) is a challenge that has received a lot of attention due to the significant risks it poses for the environment and human health. Plastics find their way to the ocean from land via the river system. Studying and obtaining a better understanding of the mechanisms contributing to the fate of plastic litter is therefore important in proactively devising methods to reduce their quantity or produce designs to trap plastic pollutants and prevent them from entering the ocean through estuaries. In this context, it is a common observation of hydraulic practitioners and field geomorphologists, that plastic litter can be trapped within riparian vegetation patches along streams or canals, which can be washed away in periods of high flows. To this goal this study aims to use a series of purpose specific physical experiments to examine the mechanisms of dispersion of plastic litter along the water surface of a channel with simulated riparian vegetation. The set of experiments are conducted in a recirculating flume with rigid riverbank and riparian vegetation modeled by a large number of acrylic rods, placed on the top of the riverbank section. Six different sizes of pieces of Styrofoam are used to simulate plastic litter. These are released from different locations upstream and in the vicinity of the riparian vegetation for various configurations (linear, staggered and random) of characteristic solid density. The trajectory of the plastic litter is recorded with a camera offering a top view of the arrangement. From the analysis of this a variety of results are obtained including transport metrics (including transport velocity and time to trapping) and litter-trapping location. The relation between the size of the litter, the vegetation configuration and the traveling

  18. Plastics recycling: challenges and opportunities.

    Science.gov (United States)

    Hopewell, Jefferson; Dvorak, Robert; Kosior, Edward

    2009-07-27

    Plastics are inexpensive, lightweight and durable materials, which can readily be moulded into a variety of products that find use in a wide range of applications. As a consequence, the production of plastics has increased markedly over the last 60 years. However, current levels of their usage and disposal generate several environmental problems. Around 4 per cent of world oil and gas production, a non-renewable resource, is used as feedstock for plastics and a further 3-4% is expended to provide energy for their manufacture. A major portion of plastic produced each year is used to make disposable items of packaging or other short-lived products that are discarded within a year of manufacture. These two observations alone indicate that our current use of plastics is not sustainable. In addition, because of the durability of the polymers involved, substantial quantities of discarded end-of-life plastics are accumulating as debris in landfills and in natural habitats worldwide. Recycling is one of the most important actions currently available to reduce these impacts and represents one of the most dynamic areas in the plastics industry today. Recycling provides opportunities to reduce oil usage, carbon dioxide emissions and the quantities of waste requiring disposal. Here, we briefly set recycling into context against other waste-reduction strategies, namely reduction in material use through downgauging or product reuse, the use of alternative biodegradable materials and energy recovery as fuel. While plastics have been recycled since the 1970s, the quantities that are recycled vary geographically, according to plastic type and application. Recycling of packaging materials has seen rapid expansion over the last decades in a number of countries. Advances in technologies and systems for the collection, sorting and reprocessing of recyclable plastics are creating new opportunities for recycling, and with the combined actions of the public, industry and governments it

  19. Plastics recycling: challenges and opportunities

    Science.gov (United States)

    Hopewell, Jefferson; Dvorak, Robert; Kosior, Edward

    2009-01-01

    Plastics are inexpensive, lightweight and durable materials, which can readily be moulded into a variety of products that find use in a wide range of applications. As a consequence, the production of plastics has increased markedly over the last 60 years. However, current levels of their usage and disposal generate several environmental problems. Around 4 per cent of world oil and gas production, a non-renewable resource, is used as feedstock for plastics and a further 3–4% is expended to provide energy for their manufacture. A major portion of plastic produced each year is used to make disposable items of packaging or other short-lived products that are discarded within a year of manufacture. These two observations alone indicate that our current use of plastics is not sustainable. In addition, because of the durability of the polymers involved, substantial quantities of discarded end-of-life plastics are accumulating as debris in landfills and in natural habitats worldwide. Recycling is one of the most important actions currently available to reduce these impacts and represents one of the most dynamic areas in the plastics industry today. Recycling provides opportunities to reduce oil usage, carbon dioxide emissions and the quantities of waste requiring disposal. Here, we briefly set recycling into context against other waste-reduction strategies, namely reduction in material use through downgauging or product reuse, the use of alternative biodegradable materials and energy recovery as fuel. While plastics have been recycled since the 1970s, the quantities that are recycled vary geographically, according to plastic type and application. Recycling of packaging materials has seen rapid expansion over the last decades in a number of countries. Advances in technologies and systems for the collection, sorting and reprocessing of recyclable plastics are creating new opportunities for recycling, and with the combined actions of the public, industry and governments it

  20. Sustainable reverse logistics for household plastic waste

    NARCIS (Netherlands)

    Bing, X.

    2014-01-01

    Summary of the thesis titled “Sustainable Reverse Logistics for Household Plastic Waste”

    PhD Candidate: Xiaoyun Bing

    Recycled plastic can be used in the manufacturing of plastic products to reduce the use of virgin plastics material. The cost of recycled plastics is usually lower

  1. Archaeological analogous and industrials for deep storage: study of the archaeological metallic piece

    International Nuclear Information System (INIS)

    Criado Portal, A. J.; Martinez Garcia, J. A.; Calabres Molina, R.; Garcia abajo, A.; Penco Valenzuela, F.; Lecanda Esteban, J. A.; Garcia Bartual, M.; Jimenez Gonzalez, J. M.; Bravo Munoz, E.; Rodriguez Lobo, L. M.; Fernandez Cascos, T.; Fernandes Cordero, O.; Montero Ruiz, I.

    2000-01-01

    The aim of present research is to obtain information about archaeological analogous of iron and steel, useful for the model of deep geological repository (AGP). The analogous examined have remained buried between 1400 and 2400 years, in very assorted geochemical environments. The extraction of the archaeological pieces has been accomplished according to normalised protocols, trying to carry to the laboratory so the piece as its burial environment, avoiding all possible pollution. Trying to the archaeological analogous could provide valuable information to the AGP model, the study has been directed to related the physical-chemical characteristics of the terrain respect to the deterioration of the archaeological metallic piece. The geology of the surrounding terrain to the archaeological deposit, the geomorphological study of the terrain and data from the analysis of ground: pH, wetness, porosity, organic matter contents, bacteria presence, sulphates, carbonates, chlorides, etc., have allowed to explain the physical-chemical phenomena suffered by the archaeological iron and steel pieces. Also, an exhaustive study of the archaeological piece has been accomplished, concerning the microstructure of the corrosion layer and of the not deteriorated metallic rest. Obtained information concerns different items, such as corrosion velocity and formations of oxide layers, diffusion of chemical elements from the corrosion layer to the metal and viceversa, and structural changes in oxide layers and in the metallic remains by structural ageing. Obtained data have allowed to develop a mathematical model for calculation of corrosion velocity in buried iron and steels, based on physical-chemical variables of grounds, chemical composition and thermomechanical treatment given to the metal during its manufacture. (Author)

  2. Plastics for corrosion inhibition

    CERN Document Server

    Goldade, Victor A; Makarevich, Anna V; Kestelman, Vladimir N

    2005-01-01

    The development of polymer composites containing inhibitors of metal corrosion is an important endeavour in modern materials science and technology. Corrosion inhibitors can be located in a polymer matrix in the solid, liquid or gaseous phase. This book details the thermodynamic principles for selecting these components, their compatibility and their effectiveness. The various mechanisms of metal protection – barrier, inhibiting and electromechanical – are considered, as are the conflicting requirements placed on the structure of the combined material. Two main classes of inhibited materials (structural and films/coatings) are described in detail. Examples are given of structural plastics used in friction units subjected to mechano-chemical wear and of polymer films/coatings for protecting metal objects against corrosion.

  3. Plastic pollution on the Baltic beaches of Kaliningrad region, Russia.

    Science.gov (United States)

    Esiukova, Elena

    2017-01-30

    Contamination of sandy beaches of the Baltic Sea in Kaliningrad region is evaluated on the base of surveys carried out from June 2015 to January 2016. Quantity of macro/meso/microplastic objects in the upper 2cm of the sandy sediments of the wrack zone at 13 sampling sites all along the Russian coast is reported. Occurrence of paraffin and amber pieces at the same sites is pointed out. Special attention is paid to microplastics (range 0.5-5mm): its content ranges between 1.3 and 36.3 items per kg dry sediment. The prevailing found type is foamed plastic. No sound differences in contamination are discovered between beaches with high and low anthropogenic load. Mean level of contamination is of the same order of magnitude as has been reported by other authors for the Baltic Sea beaches. Copyright © 2016 Elsevier Ltd. All rights reserved.

  4. Nigerian Journal of Plastic Surgery

    African Journals Online (AJOL)

    The Nigerian Journal of Plastic Surgery has its objectives in publishing original articles about developments in all areas related to plastic and reconstructive surgery as well as to trauma surgery. It also serves as a means of providing a forum for correspondence, information and discussion. It also accepts review articles that ...

  5. Architecture of European Plastic Surgery

    NARCIS (Netherlands)

    Nicolai, J. -P. A.; Banic, A.; Molea, G.; Mazzola, R.; Poell, J. G.

    2006-01-01

    The architecture of European Plastic Surgery was published in 1996 [Nicolai JPA, Scuderi N. Plastic surgical Europe in an organogram. Eur J Plast Surg 1996; 19: 253-6.] It is the objective of this paper to update information of that article. Continuing medical education (CME), science, training,

  6. TYPICAL ABSENCES: RESULTS OF OWN INVESTIGATIONS

    Directory of Open Access Journals (Sweden)

    K. Yu. Mukhin

    2015-01-01

    Full Text Available Typical absences (TA are brief primary generalized epileptic seizures characterized by sudden onset and termination. According to their definition, absences consist of impairment of consciousness that is synchronously accompanied by electroencephalographic (EEG changes as generalized spike–slow wave discharges of 3 or more Hz. The authors conducted an investigation of 1261 patients with different forms of epilepsy with onset of seizures from the first days of life to the age of 18 years. The patients were followed up from 1990 to 2010. Absence seizures were detected in 231 patients, which accounts for 18.3 % of all the epileptic patients. TA were found in 102 patients, which constitutes 8.1 % of all cases of epilepsy with onset of seizures beyond the age of 18 years. The paper provides a detailed analysis of a group of patients with TA in terms of anamnestic, clinical, electroencephalographic, and neuroimaging features and the results of therapy with antiepileptic drugs (AEDs. The age of onset of TA-associated epilepsy was from 9 months to 17 years (mean 9.4 ± 4.06 years. The disease occurred most frequently in young school-age children (41.2 %. Isolated TA as the only type of seizures were observed in the clinical picture of 28 (27.5 % patients. TA were concurrent with other types of seizures in other cases. The investigators have identified 4 types of seizures which TA (generalized convulsions, myoclonic seizures, febrile seizures, and eyelid myoclonia may be concurrent with. Neuroimaging stated there were no brain changes in 85.3 % of TA-associated epilepsy cases. Moderate diffuse subatrophic changes were detected in other cases (14.7 %. Local cerebral structural abnormalities were absent. The use of antiepileptic therapy as both monotherapy and polytherapy using different combinations showed the high efficacy of AEDs. Complete remission was achieved in 84.3 % of TA-associated epilepsy cases. An AED-induced reduction in the frequency of

  7. Imaging brain plasticity after trauma

    Institute of Scientific and Technical Information of China (English)

    Zhifeng Kou; Armin Iraji

    2014-01-01

    The brain is highly plastic after stroke or epilepsy;however, there is a paucity of brain plasticity investigation after traumatic brain injury (TBI). This mini review summarizes the most recent evidence of brain plasticity in human TBI patients from the perspective of advanced magnetic resonance imaging. Similar to other forms of acquired brain injury, TBI patients also demonstrat-ed both structural reorganization as well as functional compensation by the recruitment of other brain regions. However, the large scale brain network alterations after TBI are still unknown, and the ifeld is still short of proper means on how to guide the choice of TBI rehabilitation or treat-ment plan to promote brain plasticity. The authors also point out the new direction of brain plas-ticity investigation.

  8. Size effects in crystal plasticity

    DEFF Research Database (Denmark)

    Borg, Ulrik

    2007-01-01

    Numerical analyses of plasticity size effects have been carried out for different problems using a developed strain gradient crystal plasticiy theory. The theory employs higher order stresses as work conjugates to slip gradients and uses higher order boundary conditions. Problems on localization...... of plastic flow in a single crystal, grain boundary effects in a bicrystal, and grain size effects in a polycrystal are studied. Single crystals containing micro-scale voids have also been analyzed at different loading conditions with focus on the stress and deformation fields around the voids, on void...... growth and interaction between neighboring voids, and on a comparison between the developed strain gradient crystal plasticity theory and a discrete dislocation plasticity theory. Furthermore, voids and rigid inclusions in isotropic materials have been studied using a strain gradient plasticity theory...

  9. Computational strain gradient crystal plasticity

    DEFF Research Database (Denmark)

    Niordson, Christian Frithiof; Kysar, Jeffrey W.

    2014-01-01

    A numerical method for viscous strain gradient crystal plasticity theory is presented, which incorporates both energetic and dissipative gradient effects. The underlying minimum principles are discussed as well as convergence properties of the proposed finite element procedure. Three problems...... of plane crystal plasticity are studied: pure shear of a single crystal between rigid platens as well as plastic deformation around cylindrical voids in hexagonal close packed and face centered cubic crystals. Effective in-plane constitutive slip parameters for plane strain deformation of specifically...... oriented face centered cubic crystals are developed in terms of the crystallographic slip parameters. The effect on geometrically necessary dislocation structures introduced by plastic deformation is investigated as a function of the ratio of void radius to plasticity length scale....

  10. Grain Interactions in Crystal Plasticity

    International Nuclear Information System (INIS)

    Boyle, K.P.; Curtin, W.A.

    2005-01-01

    The plastic response of a sheet metal is governed by the collective response of the underlying grains. Intragranular plasticity depends on intrinsic variables such as crystallographic orientation and on extrinsic variables such as grain interactions; however, the role of the latter is not well understood. A finite element crystal plasticity formulation is used to investigate the importance of grain interactions on intragranular plastic deformation in initially untextured polycrystalline aggregates. A statistical analysis reveals that grain interactions are of equal (or more) importance for determining the average intragranular deviations from the applied strain as compared to the orientation of the grain itself. Furthermore, the influence of the surrounding grains is found to extend past nearest neighbor interactions. It is concluded that the stochastic nature of the mesoscale environment must be considered for a proper understanding of the plastic response of sheet metals at the grain-scale

  11. A review of typical thermal fatigue failure models for solder joints of electronic components

    Science.gov (United States)

    Li, Xiaoyan; Sun, Ruifeng; Wang, Yongdong

    2017-09-01

    For electronic components, cyclic plastic strain makes it easier to accumulate fatigue damage than elastic strain. When the solder joints undertake thermal expansion or cold contraction, different thermal strain of the electronic component and its corresponding substrate is caused by the different coefficient of thermal expansion of the electronic component and its corresponding substrate, leading to the phenomenon of stress concentration. So repeatedly, cracks began to sprout and gradually extend [1]. In this paper, the typical thermal fatigue failure models of solder joints of electronic components are classified and the methods of obtaining the parameters in the model are summarized based on domestic and foreign literature research.

  12. The Effect of High Versus Low Teacher Affect and Passive Versus Active Student Activity During Music Listening on Preschool Children's Attention, Piece Preference, Time Spent Listening, and Piece Recognition.

    Science.gov (United States)

    Sims, Wendy L.

    1986-01-01

    Small-group listening lessons and subsequent individual posttests were used to judge 94 three- through five-year-old subjects' attention, paired-comparison piece preference, time spent listening, and piece recognition. Research procedures included a modified multiple baseline design and split-screen video taping of instructional sessions.…

  13. Surface flow in severe plastic deformation of metals by sliding

    International Nuclear Information System (INIS)

    Mahato, A; Yeung, H; Chandrasekar, S; Guo, Y

    2014-01-01

    An in situ study of flow in severe plastic deformation (SPD) of surfaces by sliding is described. The model system – a hard wedge sliding against a metal surface – is representative of surface conditioning processes typical of manufacturing, and sliding wear. By combining high speed imaging and image analysis, important characteristics of unconstrained plastic flow inherent to this system are highlighted. These characteristics include development of large plastic strains on the surface and in the subsurface by laminar type flow, unusual fluid-like flow with vortex formation and surface folding, and defect and particle generation. Preferred conditions, as well as undesirable regimes, for surface SPD are demarcated. Implications for surface conditioning in manufacturing, modeling of surface deformation and wear are discussed

  14. Risperidone versus typical antipsychotic medication for schizophrenia.

    Science.gov (United States)

    Hunter, R H; Joy, C B; Kennedy, E; Gilbody, S M; Song, F

    2003-01-01

    found in long-term studies (n=859, 2RCTs RR not 20% improved 0.51 CI 0.38 to 0.67 NNT 4;n=675 1RCT, RR not improved 40% 0.75 CI 0.66 to 0.84 NNT 5; n=675, 1 RCT, RR not 60% improved 0.90 CI 0.84 to 0.96, NNT 11). Risperidone was also more likely to reduce relapse at one year follow up, compared with haloperidol (n=367, 1 RCT, RR 0.64 CI 0.41 to 0.99, NNT 7). Less people allocated risperidone left studies before completion, both for short-term (n=3066, 16 RCTs, RR 0.76 CI 0.63 to 0.92, NNT 6) and long-term trials (n=1270, 4RCTs, RR 0.55 CI 0.42 to 0.73 NNT 4). For general movement disorders results favoured risperidone. People given risperidone had significantly fewer general movement disorders (including extrapyramidal side effects) than those receiving older typical antipsychotics (n=2702, 10 RCTs, RR 0.63 CI 0.56 to 0.71, NNT 3). Significantly fewer people given risperidone used antiparkinsonian drugs (n=2524, 11 RCTs, RR 0.66 CI 0.58 to 0.74, NNT 4). As regards body weight, however, four studies (n=1708) found people were more likely to gain weight if allocated risperidone compared to typical antipsychotics (RR 1.55 CI 1.25 to 1.93, NNH 3). Risperidone was no more or less likely than haloperidol to cause sexual problems such as erectile dysfunction (n=106, 2 RCTs, RR 1.55 CI 0.58 to 4.20). Finally, some results found risperidone was more likely to cause rhinitis than conventional antipsychotics (n=656, 3 RCTs, RR1.99 CI 1.24 to 3.19, NNH 3). Risperidone may be more acceptable to those with schizophrenia than older antipsychotics and have marginal benefits in terms of limited clinical improvement. Its adverse effect profile may be better than haloperidol. With the addition of more studies to this review, the publication bias evident in previous versions is no longer a significant issue. Any marginal benefits this drug may have have to be balanced against its greater cost and increased tendency to cause side effects such as weight gain. Recent important longer term

  15. Nano-Ceramic Coated Plastics

    Science.gov (United States)

    Cho, Junghyun

    2013-01-01

    Plastic products, due to their durability, safety, and low manufacturing cost, are now rapidly replacing cookware items traditionally made of glass and ceramics. Despite this trend, some still prefer relatively expensive and more fragile ceramic/glassware because plastics can deteriorate over time after exposure to foods, which can generate odors, bad appearance, and/or color change. Nano-ceramic coatings can eliminate these drawbacks while still retaining the advantages of the plastic, since the coating only alters the surface of the plastic. The surface coating adds functionality to the plastics such as self-cleaning and disinfectant capabilities that result from a photocatalytic effect of certain ceramic systems. These ceramic coatings can also provide non-stick surfaces and higher temperature capabilities for the base plastics without resorting to ceramic or glass materials. Titanium dioxide (TiO2) and zinc oxide (ZnO) are the candidates for a nano-ceramic coating to deposit on the plastics or plastic films used in cookware and kitchenware. Both are wide-bandgap semiconductors (3.0 to 3.2 eV for TiO2 and 3.2 to 3.3 eV for ZnO), so they exhibit a photocatalytic property under ultraviolet (UV) light. This will lead to decomposition of organic compounds. Decomposed products can be easily washed off by water, so the use of detergents will be minimal. High-crystalline film with large surface area for the reaction is essential to guarantee good photocatalytic performance of these oxides. Low-temperature processing (nano-ceramic coatings (TiO2, ZnO) on plastic materials (silicone, Teflon, PET, etc.) that can possess both photocatalytic oxide properties and flexible plastic properties. Processing cost is low and it does not require any expensive equipment investment. Processing can be scalable to current manufacturing infrastructure.

  16. Plasticity and beyond microstructures, crystal-plasticity and phase transitions

    CERN Document Server

    Hackl, Klaus

    2014-01-01

    The book presents the latest findings in experimental plasticity, crystal plasticity, phase transitions, advanced mathematical modeling of finite plasticity and multi-scale modeling. The associated algorithmic treatment is mainly based on finite element formulations for standard (local approach) as well as for non-standard (non-local approach) continua and for pure macroscopic as well as for directly coupled two-scale boundary value problems. Applications in the area of material design/processing are covered, ranging from grain boundary effects in polycrystals and phase transitions to deep-drawing of multiphase steels by directly taking into account random microstructures.

  17. Changes in the Floating Plastic Pollution of the Mediterranean Sea in Relation to the Distance to Land.

    Directory of Open Access Journals (Sweden)

    Maria Luiza Pedrotti

    Full Text Available The composition, size distribution, and abundance of floating plastic debris in surface waters of the Mediterranean Sea were analyzed in relation to distance to land. We combined data from previously published reports with an intensive sampling in inshore waters of the Northwestern Mediterranean. The highest plastic concentrations were found in regions distant from from land as well as in the first kilometer adjacent to the coastline. In this nearshore water strip, plastic concentrations were significantly correlated with the nearness to a coastal human population, with local areas close to large human settlements showing hundreds of thousands of plastic pieces per km2. The ratio of plastic to plankton abundance reached particularly high values for the coastal surface waters. Polyethylene, polypropylene and polyamides were the predominant plastic polymers at all distances from coast (86 to 97% of total items, although the diversity of polymers was higher in the 1-km coastal water strip due to a higher frequency of polystyrene or polyacrylic fibers. The plastic size distributions showed a gradual increase in abundance toward small sizes indicating an efficient removal of small plastics from the surface. Nevertheless, the relative abundance of small fragments (< 2 mm was higher within the 1-km coastal water strip, suggesting a rapid fragmentation down along the shoreline, likely related with the washing ashore on the beaches. This study constitutes a first attempt to determine the impact of plastic debris in areas closest to Mediterranean coast. The presence of a high concentration of plastic including tiny plastic items could have significant environmental, health and economic impacts.

  18. Degradation and depolymerization of plastic waste by local bacterial isolates and bubble column reactor

    Science.gov (United States)

    Hussein, Amal A.; Alzuhairi, Mohammed; Aljanabi, Noor H.

    2018-05-01

    Accumulation of plastics, especially Polyethylene terephthalate (PET), is an ever increasing ecological threat due to its excessive usage in everyday human life. Nowadays, there are many methods to get rid of plastic wastes including burning, recycling and burying. However, these methods are not very active since their long period, anaerobic conditions that increase the rate of toxic materials released into the environment. This work aims to study the biological degradation of PET microorganism isolated from soil sample. Thirty eight (38) bacterial isolates were isolated from ten soil and plastic waste sample collected from four different waste disposal sites in Baghdad city during different periods between December 2016 and March 2017. Isolation was performed using enrichment culture method (flasks method) by culturing the soil samples in flasks with MSM medium where there is no carbon source only PET. Results showed that Al-Za'farania sample gave a higher number of isolates (13 isolates), while other samples gave less number of isolates. Screening was performed depending on their ability to grow in liquid MSM which contains PET powder and pieces and change the color of the PET-emulsified liquid medium as well as their ability to form the clear zone on PET-MSM agar. The results showed that NH-D-1 isolate has the higher ability to degrade DPET and PET pieces. According to morphological, biochemical characterization and Vitek-2 technique, the most active isolate was identified as Acinetobacter baumannii.

  19. Pyrolysis of plastic packaging waste: A comparison of plastic residuals from material recovery facilities with simulated plastic waste.

    Science.gov (United States)

    Adrados, A; de Marco, I; Caballero, B M; López, A; Laresgoiti, M F; Torres, A

    2012-05-01

    Pyrolysis may be an alternative for the reclamation of rejected streams of waste from sorting plants where packing and packaging plastic waste is separated and classified. These rejected streams consist of many different materials (e.g., polyethylene (PE), polypropylene (PP), polystyrene (PS), polyvinyl chloride (PVC), polyethylene terephthalate (PET), acrylonitrile butadiene styrene (ABS), aluminum, tetra-brik, and film) for which an attempt at complete separation is not technically possible or economically viable, and they are typically sent to landfills or incinerators. For this study, a simulated plastic mixture and a real waste sample from a sorting plant were pyrolyzed using a non-stirred semi-batch reactor. Red mud, a byproduct of the aluminum industry, was used as a catalyst. Despite the fact that the samples had a similar volume of material, there were noteworthy differences in the pyrolysis yields. The real waste sample resulted, after pyrolysis, in higher gas and solid yields and consequently produced less liquid. There were also significant differences noted in the compositions of the compared pyrolysis products. Copyright © 2011 Elsevier Ltd. All rights reserved.

  20. International policies to reduce plastic marine pollution from single-use plastics (plastic bags and microbeads): A review.

    Science.gov (United States)

    Xanthos, Dirk; Walker, Tony R

    2017-05-15

    Marine plastic pollution has been a growing concern for decades. Single-use plastics (plastic bags and microbeads) are a significant source of this pollution. Although research outlining environmental, social, and economic impacts of marine plastic pollution is growing, few studies have examined policy and legislative tools to reduce plastic pollution, particularly single-use plastics (plastic bags and microbeads). This paper reviews current international market-based strategies and policies to reduce plastic bags and microbeads. While policies to reduce microbeads began in 2014, interventions for plastic bags began much earlier in 1991. However, few studies have documented or measured the effectiveness of these reduction strategies. Recommendations to further reduce single-use plastic marine pollution include: (i) research to evaluate effectiveness of bans and levies to ensure policies are having positive impacts on marine environments; and (ii) education and outreach to reduce consumption of plastic bags and microbeads at source. Copyright © 2017 Elsevier Ltd. All rights reserved.

  1. Water Vapor Permeation in Plastics

    Energy Technology Data Exchange (ETDEWEB)

    Keller, Paul E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Kouzes, Richard T. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2017-01-01

    Polyvinyl toluene (PVT) and polystyrene (PS) (referred to as “plastic scintillator”) are used for gamma ray detectors. A significant decrease in radiation detection performance has been observed in some PVT-based gamma-ray detectors in systems in outdoor environments as they age. Recent studies have revealed that plastic scintillator can undergo an environmentally related material degradation that adversely affects gamma ray detection performance under certain conditions and histories. A significant decrease in sensitivity has been seen in some gamma-ray detectors in some systems as they age. The degradation of sensitivity of plastic scintillator over time is due to a variety of factors, and the term “aging” is used to encompass all factors. Some plastic scintillator samples show no aging effects (no significant change in sensitivity over more than 10 years), while others show severe aging (significant change in sensitivity in less than 5 years). Aging effects arise from weather (variations in heat and humidity), chemical exposure, mechanical stress, light exposure, and loss of volatile components. The damage produced by these various causes can be cumulative, causing observable damage to increase over time. Damage may be reversible up to some point, but becomes permanent under some conditions. The objective of this report is to document the phenomenon of permeability of plastic scintillator to water vapor and to derive the relationship between time, temperature, humidity and degree of water penetration in plastic. Several conclusions are documented about the properties of water permeability of plastic scintillator.

  2. Extruding plastic scintillator at Fermilab

    International Nuclear Information System (INIS)

    Pla-Dalmau, Anna; Bross, Alain D.; Rykalin, Viktor V.

    2003-01-01

    An understanding of the costs involved in the production of plastic scintillators and the development of a less expensive material have become necessary with the prospects of building very large plastic scintillation detectors. Several factors contribute to the high cost of plastic scintillating sheets, but the principal reason is the labor-intensive nature of the manufacturing process. In order to significantly lower the costs, the current casting procedures had to be abandoned. Since polystyrene is widely used in the consumer industry, the logical path was to investigate the extrusion of commercial-grade polystyrene pellets with dopants to yield high quality plastic scintillator. This concept was tested and high quality extruded plastic scintillator was produced. The D0 and MINOS experiments are already using extruded scintillator strips in their detectors. An extrusion line has recently been installed at Fermilab in collaboration with NICADD (Northern Illinois Center for Accelerator and Detector Development). This new facility will serve to further develop and improve extruded plastic scintillator. This paper will discuss the characteristics of extruded plastic scintillator and its raw materials, the different manufacturing techniques and the current R andD program at Fermilab

  3. Space Plastic Recycling System, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Techshot's proposed Space Plastic Recycler (SPR) is an automated closed loop plastic recycling system that allows the automated conversion of disposable ISS...

  4. Durability of wood plastic composites manufactured from recycled plastic

    Directory of Open Access Journals (Sweden)

    Irina Turku

    2018-03-01

    Full Text Available The influence of accelerated weathering, xenon-arc light and freeze-thaw cycling on wood plastic composites extruded from a recycled plastic was studied. The results showed that, in general, weathering had a stronger impact on samples made from plastic waste compared to a sample made from virgin material. After weathering, the mechanical properties, tensile and flexural, were reduced by 2–30%, depending on the plastic source. Wettability of the samples was shown to play a significant role in their stability. Chemical analysis with infrared spectroscopy and surface observation with a scan electron microscope confirmed the mechanical test results. Incorporation of carbon black retained the properties during weathering, reducing the wettability of the sample, diminishing the change of mechanical properties, and improving color stability. Keywords: Environmental science, Mechanical engineering, Materials science

  5. Computer Tool for Automatically Generated 3D Illustration in Real Time from Archaeological Scanned Pieces

    Directory of Open Access Journals (Sweden)

    Luis López

    2012-11-01

    Full Text Available The graphical documentation process of archaeological pieces requires the active involvement of a professional artist to recreate beautiful illustrations using a wide variety of expressive techniques. Frequently, the artist’s work is limited by the inconvenience of working only with the photographs of the pieces he is going to illustrate. This paper presents a software tool that allows the easy generation of illustrations in real time from 3D scanned models. The developed interface allows the user to simulate very elaborate artistic styles through the creation of diagrams by using the available virtual lights. The software processes the diagrams to render an illustration from any given angle or position. Among the available virtual lights, there are well known techniques as silhouettes enhancement, hatching or toon shading.

  6. Bite Reconstruction in the Aesthetic Zone Using One-Piece Bicortical Screw Implants

    Directory of Open Access Journals (Sweden)

    Stefan Ihde

    2018-01-01

    Full Text Available The aim of this article was to present the clinical application of a new, smooth surfaced one-piece bicortical screw implant with immediate loading protocol. An 18-year-old, healthy male patient with a history of total dislocation and replantation of teeth 11 and 21 in early childhood was admitted to the clinic. Teeth 11 and 21 were extracted, and two long one-piece implants were inserted at extraction sockets in one surgical session under local anesthesia. Temporary composite crowns were placed in the patient on the same day. After 3 months, the single-phase two-layer impression was made and the composite crowns were replaced with metal-ceramic crowns. After 12 months, satisfactory aesthetic and functional results were obtained.

  7. Piecing It Together: The Effect of Background Music on Children's Puzzle Assembly.

    Science.gov (United States)

    Koolidge, Louis; Holmes, Robyn M

    2018-04-01

    This study explored the effects of background music on cognitive (puzzle assembly) task performance in young children. Participants were 87 primarily European-American children (38 boys, 49 girls; mean age = 4.77 years) enrolled in early childhood classes in the northeastern United States. Children were given one minute to complete a 12-piece puzzle task in one of three background music conditions: music with lyrics, music without lyrics, and no music. The music selection was "You're Welcome" from the Disney movie "Moana." Results revealed that children who heard the music without lyrics completed more puzzle pieces than children in either the music with lyrics or no music condition. Background music without distracting lyrics may be beneficial and superior to background music with lyrics for young children's cognitive performance even when they are engaged independently in a nonverbal task.

  8. The DS86 neutron dosimetry enigma: Some missing pieces to the puzzle

    International Nuclear Information System (INIS)

    Gold, R.

    1994-01-01

    International programs have been conducted over the last four decades to quantify the exposure of atom bomb survivors from Hiroshima and Nagasaki. Unfortunately, the quest for accurate gamma-ray and neutron exposure doses of atom bomb survivors has proven illusive. Efforts in the most recent of these programs, designated as Dosimetry System 1986 (DS86), have revealed a serious and persistent discrepancy between neutron transport calculations and thermal neutron activation measurements at the Hiroshima site, which will be called the DS86 neutron dosimetry enigma. It is established that this enigma is a complex puzzle that precludes simple solutions. This conclusion is deduced through the identification of a number of missing pieces to the puzzle. Implications and conclusions that can be inferred from these missing puzzle pieces are advanced

  9. A simple technique of intraocular lenses explantation for single-piece foldable lenses

    Directory of Open Access Journals (Sweden)

    Arup Bhaumik

    2017-01-01

    Full Text Available Foldable intraocular lenses (IOLs are most commonly used in modern-day cataract surgery. Explantation of these IOLs is not frequently encountered, but sometimes extreme situations may demand the same. Commonly explantation is achieved by bisecting the IOL inside the anterior chamber with a cutter and delivering the pieces out one by one. This may require corneal wound extension with associated damage and endothelial loss leading to visual deterioration. We devised a simple, innovative IOL explantation technique utilizing a modified Alcon A cartridge and snare. This can successfully refold the IOL to be explanted inside the eye and deliver it out through the same wound. The device has limitations with very thick optic lenses, multipiece, and silicon IOLs. In conclusion, we describe a simple, innovative, and reproducible technique to explant almost any single piece IOL without compromising the original surgery and yielding very satisfactory outcomes.

  10. Study of ancient Islamic gilded pieces combining PIXE-RBS on external microprobe with sem images

    International Nuclear Information System (INIS)

    Ynsa, M.D.; Gutierrez, P.C.; Enguita, O.; Chamon, J.; Pardo, A.I.; Arroyo, M.; Barrio, J.; Gomez-Morilla, I.; Ferretti, M.; Climent-Font, A.

    2008-01-01

    Numerous metallic objects with very aesthetic and technological qualities have been recovered by archaeological excavations. Adequate processes of restoration and conservation treatments require the accurate determination of the elemental composition and distribution within the objects, as well as the identification of the nature and distribution of the corrosion products. Ideally the identification method should cause no alteration in the sample. In this work, different archaeological pieces with a gilded look have been characterized using simultaneously PIXE and RBS at the CMAM external microprobe in order to study the gilding metalworking done in the Iberian Peninsula during the Middle Ages. The gold layer thickness and its elemental concentrations of Ag, Au and Hg were determined by both techniques and compared with the scanning electron microscopy images obtained for some fragments of pieces. (orig.)

  11. Process for the fixing of a metallic end piece on a tubular component

    International Nuclear Information System (INIS)

    Charpin, Jean.

    1975-01-01

    Under this invention the process makes it possible to joint a tubular component and in particular a tubular filter and an end piece, with a connection of great mechanical strength, perfectly leak proof and with excellent corrosion resistance, particularly with respect to fluorinated by-products. This process is therefore of great worth in fixing to a bearer a thin ceramic compound tubular filter element, since such a filter can be used in particular for the separation of uranium isotopes by gaseous diffusion and for the separation of hydrocarbons in petrochemicals. To this end, the process under consideration is characterised in that it consists in depositing a layer of ceramic material, by hot projection, at the end of the tubular element and in sealing the end piece to the end of the tubular element by the hot projection of a ceramic or metallic substance [fr

  12. Material Composition of Bucket Foundation Transition Piece for Offshore Wind Turbines

    DEFF Research Database (Denmark)

    Nezhentseva, Anastasia; Andersen, Lars; Ibsen, Lars Bo

    2010-01-01

    In Denmark, production of renewable energy is focused on offshore wind turbines, since they make little if any inconvenience for residents in inhabited areas. High requirements are placed on the installation of the foundations which can cost about 30% of the total cost of the wind turbine....... This paper deals with the transition piece for a relatively novel type of foundation, the so-called suction bucket (caisson), focusing on the design of a transition piece connecting the turbine column with a suction bucket used as a monopod foundation for an offshore wind turbine. Since the current design...... practice is limited to the use of steel-flange-reinforced shear panels for the transition piece—a production that requires extensive welding work—a desirable solution is to find a material that provides lower cost and easier manufacturing without compromising the strength and stiffness. The paper compares...

  13. Event-related brain responses while listening to entire pieces of music

    DEFF Research Database (Denmark)

    Poikonen, H; Alluri, V; Brattico, E

    2016-01-01

    ERPs in human elicited by continuous music. The ERPs were recorded during listening to a Tango Nuevo piece, a deep techno track and an acoustic lullaby. Acoustic features related to timbre, harmony, and dynamics of the audio signal were computationally extracted from the musical pieces. Negative...... deflation occurring around 100 milliseconds after the stimulus onset (N100) and positive deflation occurring around 200 milliseconds after the stimulus onset (P200) ERP responses to peak changes in the acoustic features were distinguishable and were often largest for Tango Nuevo. In addition to large...... changes in these musical features, long phases of low values that precede a rapid increase – and that we will call Preceding Low-Feature Phases – followed by a rapid increase enhanced the amplitudes of N100 and P200 responses. These ERP responses resembled those to simpler sounds, making it possible...

  14. Developmental plasticity: Friend or foe?

    Science.gov (United States)

    Michels, Karin B

    2017-01-01

    Developmental plasticity - the concept that adaptation to changing and unfavorable environmental conditions are possible but may come at the price of compromised health potentials - has evolutionary grounding as it facilitates survival but dissents with fundamental evolutionary principles in that it may advance the lesser fit. It is an important cornerstone of the Developmental Origins of Health and Disease (DOHaD). Unlike evolutionary adaptation developmental plasticity may be short-lived and restricted to one or few generations and inheritance is uncertain. Potential mechanisms include epigenetic modifications adopted in utero which may not transmit to the next generation; future insights may allow adjustments of the outcomes of developmental plasticity.

  15. Radiation damage in plastic scintillators

    International Nuclear Information System (INIS)

    Majewski, S.

    1990-01-01

    Results of radiation damage studies in plastic scintillators are reviewed and critically analyzed from the point of view of applications of plastic scintillators in calorimetric detectors for the SSC. Damage to transmission and to fluorescent yield in different conditions is discussed. New directions in R ampersand D are outlined. Several examples are given of the most recent data on the new scintillating materials made with old and new plastics and fluors, which are exhibiting significantly improved radiation resistance. With a present rate of a vigorous R D programme, the survival limits in the vicinity of 100 MRad seem to be feasible within a couple of years

  16. Plastics recycling: challenges and opportunities

    OpenAIRE

    Hopewell, Jefferson; Dvorak, Robert; Kosior, Edward

    2009-01-01

    Plastics are inexpensive, lightweight and durable materials, which can readily be moulded into a variety of products that find use in a wide range of applications. As a consequence, the production of plastics has increased markedly over the last 60 years. However, current levels of their usage and disposal generate several environmental problems. Around 4 per cent of world oil and gas production, a non-renewable resource, is used as feedstock for plastics and a further 3–4% is expended to pro...

  17. Recycling of Reinforced Plastics

    Science.gov (United States)

    Adams, R. D.; Collins, Andrew; Cooper, Duncan; Wingfield-Digby, Mark; Watts-Farmer, Archibald; Laurence, Anna; Patel, Kayur; Stevens, Mark; Watkins, Rhodri

    2014-02-01

    This work has shown is that it is possible to recycle continuous and short fibre reinforced thermosetting resins while keeping almost the whole of the original material, both fibres and matrix, within the recyclate. By splitting, crushing hot or cold, and hot forming, it is possible to create a recyclable material, which we designate a Remat, which can then be used to remanufacture other shapes, examples of plates and tubes being demonstrated. Not only can remanufacturing be done, but it has been shown that over 50 % of the original mechanical properties, such as the E modulus, tensile strength, and interlaminar shear strength, can be retained. Four different forms of composite were investigated, a random mat Glass Fibre Reinforced Plastic (GFRP) bathroom component and boat hull, woven glass and carbon fibre cloth impregnated with an epoxy resin, and unidirectional carbon fibre pre-preg. One of the main factors found to affect composite recyclability was the type of resin matrix used in the composite. Thermoset resins tested were shown to have a temperature range around the Glass Transition Temperature (Tg) where they exhibit ductile behaviour, hence aiding reforming of the material. The high-grade carbon fibre prepreg was found to be less easy to recycle than the woven of random fibre laminates. One method of remanufacturing was by heating the Remat to above its glass transition temperature, bending it to shape, and then cooling it. However, unless precautions are taken, the geometric form may revert. This does not happen with the crushed material.

  18. Wood plastic combination

    International Nuclear Information System (INIS)

    Cunanan, S.A.; Bonoan, L.S.; Verceluz, F.P.; Azucena, E.A.

    1976-03-01

    The purpose of this study is to improve the physical and mechaniproperties of local inferior quality wood species by radiation-induced graft polymerization with plastic monomers. The process involves the following: 1) Preparation of sample; 2) Impregnation of sample with the monomers; 3) Irradiation of the impregnated sample with the use of 20,000 curie Co-60 as gamma-source; 4) Drying of irradiated sample to remove the unpolymerized monomer. Experimentation on different wood species were undertaken and the results given. From the results obtained, it can be concluded that the monomers systems MMA, MMA-USP, and styrene-USP are suitable for graft polymerization with the wood species almon, apitong, bagtikan, mayapis, red lauan, and tanguile. This is shown by their maximum conversion value which range from 86% to 96% with the optimum dose range of 1 to 2 Mrads. However, in the application of WPC process, properties that are required in a given wood product must be considered, thus aid in the selection of the monomer system to be used with a particular wood species. Some promising applications of WPC is in the manufacture of picker sticks, shuttles, and bobbins for the textile industry. However, there is a need for a pilot plant scale study so that an economic assessment of the commercial feasibility of this process can be made

  19. Accuracy of Setting Work-pieces on Automatic Lines with Pallet-fixtures

    Directory of Open Access Journals (Sweden)

    L. A. Kolesnikov

    2015-01-01

    Full Text Available The accuracy of positioning surfaces to be processed on automatic lines with pallet-fixtures essentially depends on the setting error of the pallet-fixtures with work-pieces in ready-to-work position.The applied methods for calculating the setting error do not give a complete picture of the possible coordinates of the point when in the pallet is displaced in different directions.The aim of the work was to determine an accuracy of the setting work-pieces on automatic lines with pallets-fixtures, using a computational and analytical method, to improve a manufacturing precision of parts.The currently used methods to calculate the setting error do not give a complete picture of the possible coordinates of the point of the pallet displacement in different directions. The paper offers a method of equivalent mechanism to determine all the variety of options for displacements in the horizontal plane with a diverse combination of angular and plane-parallel displacements.Using a four-bar linkage, as an equivalent mechanism, allows us to define a zone of the possible positions of any point of the work-piece pallet platform, as the zone bounded by the coupler curve. In case the gaps in the nodes of the two fixtures are equal the zone of possible positions of the point in the parallel displacement of the platform is determined by the circumference and at an angular displacement by the ellipse.The obtained analytical dependences allow us to determine the error at the stage of design with the certain gaps in the fixture nodes.The above method of calculation makes it possible to define a zone of the appropriate placement of the work-piece on its platform for the specified parameters of the pallet to meet conditions for ensuring the coordinate accuracy of the processed axes of holes.

  20. Time to Stop Holding the Elevator: A New Piece of the Transport Protein Mechanism Puzzle.

    Science.gov (United States)

    Vastermark, Ake; Saier, Milton H

    2016-06-07

    In this issue of Structure, McCoy et al. (2016) describe the 2.55-Å X-ray structure of the outward-facing occluded conformation of the Bacillus cereus maltose transporter MalT. This structure represents the penultimate piece needed to complete the picture of the transport cycle of the glucose superfamily of membrane-spanning EIIC components. Copyright © 2016 Elsevier Ltd. All rights reserved.

  1. FEA analysis and design optimization for a multifunctional piece of furniture

    OpenAIRE

    Haraga Georgeta; Goanță Adrian Mihai

    2017-01-01

    The paper presents an original approach to the integration of computer aided design and finite element analysis for a multifunctional piece of furniture using CATIA Generative Structural Analysis workbench. Finite Element Analysis (FEA) application is an important engineering technique in the furniture industry. FEA is an accurate method for numerical solution of field problems. A major problem of mesh generation today is access to CAD geometry in a efficient and precise manner. Starting with...

  2. Design and analysis of the Collider SPXA/SPRA spool piece vacuum barrier

    International Nuclear Information System (INIS)

    Cruse, G.; Aksel, G.

    1993-04-01

    A design for the Collider SPXA/SPRA spool piece vacuum barrier was developed to meet a variety of thermal and structural performance requirements. Both composite and stainless steel alternatives were investigated using detailed finite-element analysis before selecting an optimized version of the ASST SPR spool vacuum barrier design. This design meets the structural requirements and will be able to meet the thermal performance requirements by using some newer thermal strapping configurations

  3. What if the hand piece spring disassembles during robotic radical prostatectomy?

    Science.gov (United States)

    Akbulut, Ziya; Canda, Abdullah Erdem; Atmaca, Ali Fuat; Asil, Erem; Isgoren, Egemen; Balbay, Mevlana Derya

    2011-01-01

    Robot-assisted laparoscopic radical prostatectomy (RALRP) is successfully being performed for treating prostate cancer (PCa). However, instrumentation failure associated with robotic procedures represents a unique new problem. We report the successful completion of RALRP in spite of a disassembled hand piece spring during the procedure. A PubMed/Medline search was made concerning robotic malfunction and robot-assisted laparoscopic radical prostatectomy to discuss our experience. We performed RALRP in a 60-year-old male patient with localized PCa. During the procedure, the spring of the hand piece disassembled, and we were not able to reassemble it. We completed the procedure successfully however without fixing the disassembled hand piece spring. We were able to grasp tissue and needles when we brought our fingers together. The only movement we needed to do was to move fingers apart to release tissue or needles caught by robotic instrument. Although malfunction risk related to the da Vinci Surgical System seems to be very low, it might still occur. Sometimes, simple maneuvers may compensate for the failed function as occurred in our case. However, patients should be informed before the operation about the possibility of converting their procedure to laparoscopic or open due to robotic malfunction.

  4. Leaching of metals from large pieces of printed circuit boards using citric acid and hydrogen peroxide.

    Science.gov (United States)

    Jadhav, Umesh; Su, C; Hocheng, Hong

    2016-12-01

    In the present study, the leaching of metals from large pieces of computer printed circuit boards (CPCBs) was studied. A combination of citric acid (0.5 M) and 1.76 M hydrogen peroxide (H 2 O 2 ) was used to leach the metals from CPCB piece. The influence of system variables such as H 2 O 2 concentration, concentration of citric acid, shaking speed, and temperature on the metal leaching process was investigated. The complete metal leaching was achieved in 4 h from a 4 × 4 cm CPCB piece. The presence of citric acid and H 2 O 2 together in the leaching solution is essential for complete metal leaching. The optimum addition amount of H 2 O 2 was 5.83 %. The citric acid concentration and shaking speed had an insignificant effect on the leaching of metals. The increase in the temperature above 30 °C showed a drastic effect on metal leaching process.

  5. FEA and microstructure characterization of a one-piece Y-TZP abutment.

    Science.gov (United States)

    da Silva, Lucas Hian; Ribeiro, Sebastião; Borges, Alexandre Luís Souto; Cesar, Paulo Francisco; Tango, Rubens Nisie

    2014-11-01

    The most important drawback of dental implant/abutment assemblies is the need for a fixing screw. This study aimed to develop an esthetic one-piece Y-TZP abutment to suppress the use of the screw. Material characterization was performed using a bar-shaped specimen obtained by slip-casting to validate the method prior to prototype abutment fabrication by the same process. The mechanical behavior of the prototype abutment was verified and compared with a conventional abutment by finite element analysis (FEA). The abutment was evaluated by micro-CT analysis and its density was measured. FEA showed stress concentration at the first thread pitch during installation and in the cervical region during oblique loading for both abutments. However, stress concentration was observed at the base of the screw head and stem in the conventional abutment. The relative density for the fabricated abutment was 95.68%. Micro-CT analysis revealed the presence of elongated cracks with sharp edges over the surface and porosity in the central region. In the light of these findings, the behavior of a one-piece abutment is expected to be better than that of the conventional model. New studies should be conducted to clarify the performance and longevity of this one-piece Y-TZP abutment. Copyright © 2014 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  6. [Simultaneous intrusion and retraction of the anterior teeth using a three-piece base arch].

    Science.gov (United States)

    Liu, D; Bai, D; Wang, C; Sun, W; Guo, J; Xi, R

    2000-06-01

    To evaluate the effects of the three-piece base arch on overbite correction of Class II malocclusion. 20 patients with high angle, flared incisors were treated using a three-piece base arch appliance. The intrusion force of four upper incisors was adjusted to approximately 50 g. The line of force action was 2 mm distally to the resistant center(RC) and the retraction force was 20 g, the right and left posterior segments were joined by a palatal bar. Cephalograms were taken before treatment (T1) and six months after treatment (T2). The upper molars moved mesially 0.60 +/- 0.35 mm and the distance of the vertical extrusion was 0.80 +/- 0.52 mm. The distances of the upper central incisor retraction and intrusion were -4.20 +/- 2.12 mm and 3.10 +/- 0.54 mm respectively. The RC of the central incisor retracted -4.12 +/- 1.96 mm and intruded 3.20 +/- 0.66 mm. The axial inclination of the upper incisor-palatal plane changed from 123.21 degrees +/- 4.26 degrees to 116.00 degrees +/- 3.96 degrees. The three-piece segmented approach can effectively intrude and retract the upper anterior teeth for flared incisors and deep overbite.

  7. Inline inspection of textured plastics surfaces

    Science.gov (United States)

    Michaeli, Walter; Berdel, Klaus

    2011-02-01

    This article focuses on the inspection of plastics web materials exhibiting irregular textures such as imitation wood or leather. They are produced in a continuous process at high speed. In this process, various defects occur sporadically. However, current inspection systems for plastics surfaces are able to inspect unstructured products or products with regular, i.e., highly periodic, textures, only. The proposed inspection algorithm uses the local binary pattern operator for texture feature extraction. For classification, semisupervised as well as supervised approaches are used. A simple concept for semisupervised classification is presented and applied for defect detection. The resulting defect-maps are presented to the operator. He assigns class labels that are used to train the supervised classifier in order to distinguish between different defect types. A concept for parallelization is presented allowing the efficient use of standard multicore processor PC hardware. Experiments with images of a typical product acquired in an industrial setting show a detection rate of 97% while achieving a false alarm rate below 1%. Real-time tests show that defects can be reliably detected even at haul-off speeds of 30 m/min. Further applications of the presented concept can be found in the inspection of other materials.

  8. Composition of plastics from waste electrical and electronic equipment (WEEE) by direct sampling

    International Nuclear Information System (INIS)

    Martinho, Graça; Pires, Ana; Saraiva, Luanha; Ribeiro, Rita

    2012-01-01

    Highlights: ► The article shows WEEE plastics characterization from a recycling unit in Portugal. ► The recycling unit has low machinery, with hand sorting of plastics elements. ► Most common polymers are PS, ABS, PC/ABS, HIPS and PP. ► Most plastics found have no identification of plastic type or flame retardants. ► Ecodesign is still not practiced for EEE, with repercussions in end of life stage. - Abstract: This paper describes a direct analysis study carried out in a recycling unit for waste electrical and electronic equipment (WEEE) in Portugal to characterize the plastic constituents of WEEE. Approximately 3400 items, including cooling appliances, small WEEE, printers, copying equipment, central processing units, cathode ray tube (CRT) monitors and CRT televisions were characterized, with the analysis finding around 6000 kg of plastics with several polymer types. The most common polymers are polystyrene, acrylonitrile–butadiene–styrene, polycarbonate blends, high-impact polystyrene and polypropylene. Additives to darken color are common contaminants in these plastics when used in CRT televisions and small WEEE. These additives can make plastic identification difficult, along with missing polymer identification and flame retardant identification marks. These drawbacks contribute to the inefficiency of manual dismantling of WEEE, which is the typical recycling process in Portugal. The information found here can be used to set a baseline for the plastics recycling industry and provide information for ecodesign in electrical and electronic equipment production.

  9. Temporal Dynamics of Bacterial and Fungal Colonization on Plastic Debris in the North Sea.

    Science.gov (United States)

    De Tender, Caroline; Devriese, Lisa I; Haegeman, Annelies; Maes, Sara; Vangeyte, Jürgen; Cattrijsse, André; Dawyndt, Peter; Ruttink, Tom

    2017-07-05

    Despite growing evidence that biofilm formation on plastic debris in the marine environment may be essential for its biodegradation, the underlying processes have yet to be fully understood. Thus, far, bacterial biofilm formation had only been studied after short-term exposure or on floating plastic, yet a prominent share of plastic litter accumulates on the seafloor. In this study, we explored the taxonomic composition of bacterial and fungal communities on polyethylene plastic sheets and dolly ropes during long-term exposure on the seafloor, both at a harbor and an offshore location in the Belgian part of the North Sea. We reconstructed the sequence of events during biofilm formation on plastic in the harbor environment and identified a core bacteriome and subsets of bacterial indicator species for early, intermediate, and late stages of biofilm formation. Additionally, by implementing ITS2 metabarcoding on plastic debris, we identified and characterized for the first time fungal genera on plastic debris. Surprisingly, none of the plastics exposed to offshore conditions displayed the typical signature of a late stage biofilm, suggesting that biofilm formation is severely hampered in the natural environment where most plastic debris accumulates.

  10. Energy recovery from plastic wastes

    Energy Technology Data Exchange (ETDEWEB)

    Baur, A; Atzger, J

    1983-07-01

    The conversion of plastic wastes to energy is suggested as a practicable and advantageous alternative to recycling. A two-stage pilot gasification plant for the pyrolysis of wastes is described and the utilization of the resulting fuel gas discussed.

  11. Plasticity and creep of metals

    CERN Document Server

    Rusinko, Andrew

    2011-01-01

    Here is a systematic presentation of the postulates, theorems and principles of mathematical theories of plasticity and creep in metals, and their applications. Special attention is paid to analysis of the advantages and shortcomings of the classical theories.

  12. Neuromodulation, development and synaptic plasticity.

    Science.gov (United States)

    Foehring, R C; Lorenzon, N M

    1999-03-01

    We discuss parallels in the mechanisms underlying use-dependent synaptic plasticity during development and long-term potentiation (LTP) and long-term depression (LTD) in neocortical synapses. Neuromodulators, such as norepinephrine, serotonin, and acetylcholine have also been implicated in regulating both developmental plasticity and LTP/LTD. There are many potential levels of interaction between neuromodulators and plasticity. Ion channels are substrates for modulation in many cell types. We discuss examples of modulation of voltage-gated Ca2+ channels and Ca(2+)-dependent K+ channels and the consequences for neocortical pyramidal cell firing behaviour. At the time when developmental plasticity is most evident in rat cortex, the substrate for modulation is changing as the densities and relative proportions of various ion channels types are altered during ontogeny. We discuss examples of changes in K+ and Ca2+ channels and the consequence for modulation of neuronal activity.

  13. WEATHERABILITY OF ENHANCED DEGRADABLE PLASTICS

    Science.gov (United States)

    The main objective of this study was to assess the performance and the asociated variability of several selected enhanced degradable plastic materials under a variety of different exposure conditions. Other objectives were to identify the major products formed during degradation ...

  14. Computational materials science: Nanoscale plasticity

    DEFF Research Database (Denmark)

    Jacobsen, Karsten Wedel; Schiøtz, Jakob

    2002-01-01

    How does plastic deformation of polycrystalline materials with grain sizes less than 100 nm look at the atomic scale? A large-scale molecular dynamics simulation of nanocrystalline alluminium reveals some surprising behaviour.......How does plastic deformation of polycrystalline materials with grain sizes less than 100 nm look at the atomic scale? A large-scale molecular dynamics simulation of nanocrystalline alluminium reveals some surprising behaviour....

  15. Biocide Usage in Plastic Products

    OpenAIRE

    Kavak, Nergizhan; Çakır, Ayşegül; Koltuk, Fatmagül; Uzun, Utku

    2015-01-01

    People’s demand of improving their life quality caused to the term of hygiene become popular and increased the tendency to use more reliable and healthy products. This tendency makes the continuous developments in the properties of the materials used in manufactured goods compulsory. It is possible to create anti-bacterial plastic products by adding biocidal additives to plastic materials which have a wide-range of application in the areas such as health (medicine), food and many other indust...

  16. Interhemispheric plasticity in humans.

    Science.gov (United States)

    Hortobágyi, Tibor; Richardson, Sarah Pirio; Lomarev, Mikhael; Shamim, Ejaz; Meunier, Sabine; Russman, Heike; Dang, Nguyet; Hallett, Mark

    2011-07-01

    Chronic unimanual motor practice increases the motor output not only in the trained but also in the nonexercised homologous muscle in the opposite limb. We examined the hypothesis that adaptations in motor cortical excitability of the nontrained primary motor cortex (iM1) and in interhemispheric inhibition from the trained to the nontrained M1 mediate this interlimb cross education. Healthy, young volunteers (n=12) performed 1000 submaximal voluntary contractions (MVC) of the right first dorsal interosseus (FDI) at 80% MVC during 20 sessions. Trained FDI's MVC increased 49.9%, and the untrained FDI's MVC increased 28.1%. Although corticospinal excitability in iM1, measured with transcranial magnetic stimulation (TMS) before and after every fifth session, increased 6% at rest, these changes, as those in intracortical inhibition and facilitation, did not correlate with cross education. When weak and strong TMS of iM1 were delivered on a background of a weak and strong muscle contraction, respectively, of the right FDI, excitability of iM1 increased dramatically after 20 sessions. Interhemispheric inhibition decreased 8.9% acutely within sessions and 30.9% chronically during 20 sessions and these chronic reductions progressively became more strongly associated with cross education. There were no changes in force or TMS measures in the trained group's left abductor minimi digiti and there were no changes in the nonexercising control group (n=8). The findings provide the first evidence for plasticity of interhemispheric connections to mediate cross education produced by a simple motor task.

  17. A study of wrecked Dovekies (Alle alle) in the western North Atlantic highlights the importance of using standardized methods to quantify plastic ingestion.

    Science.gov (United States)

    Avery-Gomm, Stephanie; Valliant, Michelle; Schacter, Carley R; Robbins, Katherine F; Liboiron, Max; Daoust, Pierre-Yves; Rios, Lorena M; Jones, Ian L

    2016-12-15

    Quantification of plastic ingestion across a range of seabirds is required to assess the prevalence of plastics in marine food webs. We quantified plastic ingestion in beached Dovekies (Alle alle), following a wreck in Newfoundland, Canada. Of 171 birds, 30.4% had ingested plastic (mean 0.81±0.30 SE pieces per bird, mass 0.005±0.002 SE g per bird). Most plastics were fragments of polyethylene and polypropylene. Surprisingly, 37% were burned or melted, indicating a previously unreported source of ingested plastics (incinerated waste). We found no relationship between plastic ingestion and age, sex or body condition. By comparing our results with a similar nearby study, we illustrate the need for researchers to adopt standardized methods for plastic ingestion studies. We underline the importance of using histological techniques to reliably identify gastric pathologies, and advise caution when inferring population level trends in plastic ingestion from studies of emaciated, wrecked birds. Copyright © 2016 Elsevier Ltd. All rights reserved.

  18. ARE PLASTIC GROCERY BAGS SACKING THE ENVIRONMENT?

    OpenAIRE

    Mangal Gogte

    2009-01-01

    This paper is oriented on analysis impacts of plastic bags on environment. In this paper is analyzed did plastic bags are so harmful, and what are the main ingredients of it. One part of this paper is oriented on effects of plastic bags and management of their usage. There is also made comparative analysis between impacts of plastic and paper bags on environment.

  19. Experiments with elasto-plastic oscillator

    DEFF Research Database (Denmark)

    Randrup-thomsen, Søren; Ditlevsen, Ove Dalager

    1996-01-01

    Plastic displacements of a Gaussian white noise excited three degrees of freedom non-ideal elasto-plastic oscillator are measured in laboratory experiments and the plastic displacements are compared to computer simulated results for the corresponding ideal elasto-plastic oscillator. The comparative...

  20. Experiments with elasto-plastic oscillator

    DEFF Research Database (Denmark)

    Randrup-Thomsen, S.; Ditlevsen, Ove Dalager

    1999-01-01

    Plastic displacements of a Gaussian white noise excited three degrees of freedom non-ideal elasto-plastic oscillator are measured in laboratory experiments and the plastic displacements are compared to computer simulated results for the corresponding ideal elasto-plastic oscillator. The comparative...

  1. Validation of ATR FT-IR to identify polymers of plastic marine debris, including those ingested by marine organisms

    Science.gov (United States)

    Jung, Melissa R.; Horgen, F. David; Orski, Sara V.; Rodriguez, Viviana; Beers, Kathryn L.; Balazs, George H.; Jones, T. Todd; Work, Thierry M.; Brignac, Kayla C.; Royer, Sarah-Jeanne; Hyrenbach, David K.; Jensen, Brenda A.; Lynch, Jennifer M.

    2018-01-01

    Polymer identification of plastic marine debris can help identify its sources, degradation, and fate. We optimized and validated a fast, simple, and accessible technique, attenuated total reflectance Fourier transform infrared spectroscopy (ATR FT-IR), to identify polymers contained in plastic ingested by sea turtles. Spectra of consumer good items with known resin identification codes #1–6 and several #7 plastics were compared to standard and raw manufactured polymers. High temperature size exclusion chromatography measurements confirmed ATR FT-IR could differentiate these polymers. High-density (HDPE) and low-density polyethylene (LDPE) discrimination is challenging but a clear step-by-step guide is provided that identified 78% of ingested PE samples. The optimal cleaning methods consisted of wiping ingested pieces with water or cutting. Of 828 ingested plastics pieces from 50 Pacific sea turtles, 96% were identified by ATR FT-IR as HDPE, LDPE, unknown PE, polypropylene (PP), PE and PP mixtures, polystyrene, polyvinyl chloride, and nylon.

  2. Relaxation of the single-slip condition in strain-gradient plasticity.

    Science.gov (United States)

    Anguige, Keith; Dondl, Patrick W

    2014-09-08

    We consider the variational formulation of both geometrically linear and geometrically nonlinear elasto-plasticity subject to a class of hard single-slip conditions. Such side conditions typically render the associated boundary-value problems non-convex. We show that, for a large class of non-smooth plastic distortions, a given single-slip condition (specification of Burgers vectors) can be relaxed by introducing a microstructure through a two-stage process of mollification and lamination. The relaxed model can be thought of as an aid to simulating macroscopic plastic behaviour without the need to resolve arbitrarily fine spatial scales.

  3. Effect of plasticity on cleavage crack growth resistance at an interface

    DEFF Research Database (Denmark)

    Tvergaard, Viggo

    1999-01-01

    The mixed mode toughness of an interface joining an elastic-plastic metal to a solid which does not yield plastically is studied numerically for cases where fracture occurs by atomic separation. Thus, the length scale of the fracture process is typically much smaller than the dislocation spacing...... of a thin elastic strip of material along the metal side of the crack tip, while the metal outside the strip is described by continuum plasticity. Most of the computations use an infinitely long elastic strip to represent the elastic core region around the tip, but the approximation of using a long strip...

  4. Seeking missing pieces in science concept assessments: Reevaluating the Brief Electricity and Magnetism Assessment through Rasch analysis

    Science.gov (United States)

    Ding, Lin

    2014-02-01

    Discipline-based science concept assessments are powerful tools to measure learners' disciplinary core ideas. Among many such assessments, the Brief Electricity and Magnetism Assessment (BEMA) has been broadly used to gauge student conceptions of key electricity and magnetism (E&M) topics in college-level introductory physics courses. Differing from typical concept inventories that focus only on one topic of a subject area, BEMA covers a broad range of topics in the electromagnetism domain. In spite of this fact, prior studies exclusively used a single aggregate score to represent individual students' overall understanding of E&M without explicating the construct of this assessment. Additionally, BEMA has been used to compare traditional physics courses with a reformed course entitled Matter and Interactions (M&I). While prior findings were in favor of M&I, no empirical evidence was sought to rule out possible differential functioning of BEMA that may have inadvertently advantaged M&I students. In this study, we used Rasch analysis to seek two missing pieces regarding the construct and differential functioning of BEMA. Results suggest that although BEMA items generally can function together to measure the same construct of application and analysis of E&M concepts, several items may need further revision. Additionally, items that demonstrate differential functioning for the two courses are detected. Issues such as item contextual features and student familiarity with question settings may underlie these findings. This study highlights often overlooked threats in science concept assessments and provides an exemplar for using evidence-based reasoning to make valid inferences and arguments.

  5. Seeking missing pieces in science concept assessments: Reevaluating the Brief Electricity and Magnetism Assessment through Rasch analysis

    Directory of Open Access Journals (Sweden)

    Lin Ding

    2014-02-01

    Full Text Available Discipline-based science concept assessments are powerful tools to measure learners’ disciplinary core ideas. Among many such assessments, the Brief Electricity and Magnetism Assessment (BEMA has been broadly used to gauge student conceptions of key electricity and magnetism (E&M topics in college-level introductory physics courses. Differing from typical concept inventories that focus only on one topic of a subject area, BEMA covers a broad range of topics in the electromagnetism domain. In spite of this fact, prior studies exclusively used a single aggregate score to represent individual students’ overall understanding of E&M without explicating the construct of this assessment. Additionally, BEMA has been used to compare traditional physics courses with a reformed course entitled Matter and Interactions (M&I. While prior findings were in favor of M&I, no empirical evidence was sought to rule out possible differential functioning of BEMA that may have inadvertently advantaged M&I students. In this study, we used Rasch analysis to seek two missing pieces regarding the construct and differential functioning of BEMA. Results suggest that although BEMA items generally can function together to measure the same construct of application and analysis of E&M concepts, several items may need further revision. Additionally, items that demonstrate differential functioning for the two courses are detected. Issues such as item contextual features and student familiarity with question settings may underlie these findings. This study highlights often overlooked threats in science concept assessments and provides an exemplar for using evidence-based reasoning to make valid inferences and arguments.

  6. Plastic zonder olie : lesmodule voor nieuwe scheikunde

    OpenAIRE

    Langejan, B.; Klein Douwel, C.; Horst, ter, J.J.; Tijdink, K.; Marle, van, N.; Klaasen, P.; Coolen, R.; Assenbergh, van, P.; Sijbers, J.P.J.; Mast, A.

    2013-01-01

    Lesmodule voor nieuwe scheikunde voor leerlingen uit 5 en 6 vwo. Bioplastics worden gemaakt uit natuurlijke grondstoffen. Als ze de synthetische plastics vervangen kan de voorraad aardolie ontzien worden. Omdat veel bioplastics afbreekbaar zijn, kan ook de berg plastic afval krimpen. Maar zijn bioplastics in staat om ons de reguliere plastics te doen vergeten? Hoe maken we bioplastics met dezelfde veelzijdige eigenschappen als plastic? Waar komen de uiteenlopende eigenschappen van plastics ei...

  7. Elimination of Plastic Polymers in Natural Environments

    OpenAIRE

    Ramirez-Ekner, Sofia; Bidstrup, Marie Juliane Svea; Brusen, Nicklas Hald; Rugaard-Morgan, Zsa-Zsa Sophie Oona Ophelia

    2017-01-01

    Plastic production and consumption continues to rise and subsequently plastic waste continues to accumulates in natural environments, causing harm to ecosystems.The aim of this paper was to come up with a way to utilize organisms, that have been identified to produce plastic degrading enzymes, as a waste disposal technology. This review includes accounts of plastic production rates, the occurrence of plastic in natural environments and the current waste management systems to create an underst...

  8. Avalanches and plastic flow in crystal plasticity: an overview

    Science.gov (United States)

    Papanikolaou, Stefanos; Cui, Yinan; Ghoniem, Nasr

    2018-01-01

    Crystal plasticity is mediated through dislocations, which form knotted configurations in a complex energy landscape. Once they disentangle and move, they may also be impeded by permanent obstacles with finite energy barriers or frustrating long-range interactions. The outcome of such complexity is the emergence of dislocation avalanches as the basic mechanism of plastic flow in solids at the nanoscale. While the deformation behavior of bulk materials appears smooth, a predictive model should clearly be based upon the character of these dislocation avalanches and their associated strain bursts. We provide here a comprehensive overview of experimental observations, theoretical models and computational approaches that have been developed to unravel the multiple aspects of dislocation avalanche physics and the phenomena leading to strain bursts in crystal plasticity.

  9. Plastic material investment in load-bearing silk attachments in spiders.

    Science.gov (United States)

    Wolff, Jonas O; Jones, Braxton; Herberstein, Marie E

    2018-05-17

    The nature and size of attachments is a fundamental element of animal constructions. Presumably, these adhesive structures are plastically deployed to balance material investment and attachment strength. Here we studied plasticity in dragline anchorages of the golden orb web spider, Nephila plumipes. Specifically, we predict that spiders adjust the size and structure of dragline anchorages with load, i.e. spider mass. Mass was manipulated by attaching lead pieces to the spider's abdomen resulting in a 50 percent increase in mass. Loaded spiders spun larger but structurally similar thread anchorages than unloaded spiders. Thus, the spinning program that determines the overall anchor structure is highly stereotypic, and flexibility is introduced through varying the anchor size by increasing material investment. Our study showcases substrate attachments as suitable models to investigate the interplay between innate and changeable elements in the economy of building behaviours. Copyright © 2018 Elsevier GmbH. All rights reserved.

  10. Observations of Near-Surface Current Shear Help Describe Oceanic Oil and Plastic Transport

    Science.gov (United States)

    Laxague, Nathan J. M.; Ö-zgökmen, Tamay M.; Haus, Brian K.; Novelli, Guillaume; Shcherbina, Andrey; Sutherland, Peter; Guigand, Cédric M.; Lund, Björn; Mehta, Sanchit; Alday, Matias; Molemaker, Jeroen

    2018-01-01

    Plastics and spilled oil pose a critical threat to marine life and human health. As a result of wind forcing and wave motions, theoretical and laboratory studies predict very strong velocity variation with depth over the upper few centimeters of the water column, an observational blind spot in the real ocean. Here we present the first-ever ocean measurements of the current vector profile defined to within 1 cm of the free surface. In our illustrative example, the current magnitude averaged over the upper 1 cm of the ocean is shown to be nearly four times the average over the upper 10 m, even for mild forcing. Our findings indicate that this shear will rapidly separate pieces of marine debris which vary in size or buoyancy, making consideration of these dynamics essential to an improved understanding of the pathways along which marine plastics and oil are transported.

  11. Comparison of training in neonatal resuscitation using self inflating bag and T-piece resuscitator

    Science.gov (United States)

    Mathai, S.S.; Adhikari, K.M.; Rajeev, A.

    2014-01-01

    Background Both the self inflating bag and the T-piece resuscitator are recommended for neonatal resuscitation, but many health care workers are unfamiliar with using the latter. A prospective, comparative, observational study was done to determine the ease and effectiveness of training of health care personnel in the two devices using infant training manikins. Methods 100 health care workers, who had no prior formal training in neonatal resuscitation, were divided into small groups and trained in the use of the two devices by qualified trainers. Assessment of cognitive skills was done by pre and post MCQs. Psychomotor skill was assessed post training on manikins using a 10-point objective score. Acceptance by users was ascertained by questionnaire. Assessments were also done after 24 h and 3 months. Comparison was done by Chi square and paired t-tests. Results Pre-training cognitive tests increased from 3.77 (+1.58) to 6.99 (+1.28) on day of training which was significant. Post training assessment of psychomotor skills showed significantly higher initial scores for the T-piece group (7.07 + 2.57) on day of training. Reassessment after 24 h showed significant improvement in cognitive scores (9.89 + 1.24) and psychomotor scores in both groups (8.86 + 1.42 for self inflating bag and 9.70 + 0.57 for T-piece resuscitator). After 3–6 months the scores in both domains showed some decline which was not statistically significant. User acceptability was the same for both devices. Conclusion It is equally easy to train health care workers in both devices. Both groups showed good short term recall and both devices were equally acceptable to the users. PMID:25609858

  12. Keeping All the PIECES: Phylogenetically Informed Ex Situ Conservation of Endangered Species.

    Science.gov (United States)

    Larkin, Daniel J; Jacobi, Sarah K; Hipp, Andrew L; Kramer, Andrea T

    2016-01-01

    Ex situ conservation in germplasm and living collections is a major focus of global plant conservation strategies. Prioritizing species for ex situ collection is a necessary component of this effort for which sound strategies are needed. Phylogenetic considerations can play an important role in prioritization. Collections that are more phylogenetically diverse are likely to encompass more ecological and trait variation, and thus provide stronger conservation insurance and richer resources for future restoration efforts. However, phylogenetic criteria need to be weighed against other, potentially competing objectives. We used ex situ collection and threat rank data for North American angiosperms to investigate gaps in ex situ coverage and phylogenetic diversity of collections and to develop a flexible framework for prioritizing species across multiple objectives. We found that ex situ coverage of 18,766 North American angiosperm taxa was low with respect to the most vulnerable taxa: just 43% of vulnerable to critically imperiled taxa were in ex situ collections, far short of a year-2020 goal of 75%. In addition, species held in ex situ collections were phylogenetically clustered (P species been drawn at random. These patterns support incorporating phylogenetic considerations into ex situ prioritization in a manner balanced with other criteria, such as vulnerability. To meet this need, we present the 'PIECES' index (Phylogenetically Informed Ex situ Conservation of Endangered Species). PIECES integrates phylogenetic considerations into a flexible framework for prioritizing species across competing objectives using multi-criteria decision analysis. Applying PIECES to prioritizing ex situ conservation of North American angiosperms, we show strong return on investment across multiple objectives, some of which are negatively correlated with each other. A spreadsheet-based decision support tool for North American angiosperms is provided; this tool can be customized to

  13. Cataract Surgery with Foldable Single Piece IOLs in Congenital Cataract-Microcornea Syndrome

    Directory of Open Access Journals (Sweden)

    Niphon Chirapapaisan, M.D.

    2017-11-01

    Full Text Available Objective: To present the visual outcomes and intraocular lens (IOLs stability after cataract surgery with foldable single piece IOLs in a patient with congenital cataract-microcornea syndrome (CCMC. Case presentation: A 28-year-old woman presented with bilateral microcornea and posterior polar cataract. Her uncorrected (UDVA and corrected (CDVA distance visual acuities were 20/100, 20/160 and 20/80, 20/80, respectively. The horizontal cornea diameter was 9.0 mm in both eyes. Anterior chamber angle assessment (ACAA with Scheie classification showed grade 3 on the superior, inferior, and temporal site and grade 2 on the nasal site in both eyes. On ultrasound biomicroscopy (UBM, the anterior chamber depths were 2.35 mm. OD and 2.41 mm. OS. The axial lengths were 23.28 mm., OD and 22.50 mm. OS with the A-scan ultrasound biometry. The IOLs power calculation with SRK/T formulas was +25.00 diopter OD and +22.50 diopter OS (A-constant 118.4. Phacoemulsification was performed on both eyes. After lens aspiration, ruptured posterior capsule, a common complication occurred. Then anterior vitrectomy was performed. A foldable single piece IOLs without haptic trimming was implanted in the sulcus in each eye. CDVA was 20/63 equally in both eyes. The intraocular pressure was 12 and 14 mmHg. ACAA showed grade 2 and no pigment dispersion. The IOLs had no tilt or decentration. UBM showed the IOLs were in the proper position and were not rubbing the iris. Conclusion: The foldable single piece IOLs without haptic trimming in the sulcus were safely implanted in both eyes with microcornea in CCMC.

  14. Plasticity characteristic obtained by indentation

    International Nuclear Information System (INIS)

    Milman, Yu V

    2008-01-01

    A dimensionless parameter δ H = ε p /ε t (where ε p and ε t are the average values of plastic and total deformation of material on the contact area indenter-specimen) may be used as the plasticity characteristic of materials, which made it possible to characterize the plasticity of materials that are brittle in standard mechanical tests. δ H may be calculated from the values of microhardness HM, Young's modulus E and Poisson's ratio ν. In instrumented indentation the plasticity characteristic δ A = A p /A t (A p and A t are the work of plastic and total deformation during indentation) may be calculated. δ A ∼ δ H for materials with δ H > 0.5, i.e. for all metals and the majority of ceramic materials. In this case, the theoretical equation δ A ∼ δ H = 1-10.2 · (1 - ν - 2ν 2 )(HM/E) is satisfied in experiments with the Berkovich indenter. The influence of the temperature and structural parameters (dislocation density and grain size including nanostructured materials) on δ H is discussed

  15. Mechanisms of GABAergic Homeostatic Plasticity

    Directory of Open Access Journals (Sweden)

    Peter Wenner

    2011-01-01

    Full Text Available Homeostatic plasticity ensures that appropriate levels of activity are maintained through compensatory adjustments in synaptic strength and cellular excitability. For instance, excitatory glutamatergic synapses are strengthened following activity blockade and weakened following increases in spiking activity. This form of plasticity has been described in a wide array of networks at several different stages of development, but most work and reviews have focussed on the excitatory inputs of excitatory neurons. Here we review homeostatic plasticity of GABAergic neurons and their synaptic connections. We propose a simplistic model for homeostatic plasticity of GABAergic components of the circuitry (GABAergic synapses onto excitatory neurons, excitatory connections onto GABAergic neurons, cellular excitability of GABAergic neurons: following chronic activity blockade there is a weakening of GABAergic inhibition, and following chronic increases in network activity there is a strengthening of GABAergic inhibition. Previous work on GABAergic homeostatic plasticity supports certain aspects of the model, but it is clear that the model cannot fully account for some results which do not appear to fit any simplistic rule. We consider potential reasons for these discrepancies.

  16. Neurogenomic mechanisms of social plasticity.

    Science.gov (United States)

    Cardoso, Sara D; Teles, Magda C; Oliveira, Rui F

    2015-01-01

    Group-living animals must adjust the expression of their social behaviour to changes in their social environment and to transitions between life-history stages, and this social plasticity can be seen as an adaptive trait that can be under positive selection when changes in the environment outpace the rate of genetic evolutionary change. Here, we propose a conceptual framework for understanding the neuromolecular mechanisms of social plasticity. According to this framework, social plasticity is achieved by rewiring or by biochemically switching nodes of a neural network underlying social behaviour in response to perceived social information. Therefore, at the molecular level, it depends on the social regulation of gene expression, so that different genomic and epigenetic states of this brain network correspond to different behavioural states, and the switches between states are orchestrated by signalling pathways that interface the social environment and the genotype. Different types of social plasticity can be recognized based on the observed patterns of inter- versus intra-individual occurrence, time scale and reversibility. It is proposed that these different types of social plasticity rely on different proximate mechanisms at the physiological, neural and genomic level. © 2015. Published by The Company of Biologists Ltd.

  17. Smartphones and the plastic surgeon.

    Science.gov (United States)

    Al-Hadithy, Nada; Ghosh, Sudip

    2013-06-01

    Surgical trainees are facing limited training opportunities since the introduction of the European Working Time Directive. Smartphone sales are increasing and have usurped computer sales for the first time. In this context, smartphones are an important portable reference and educational tool, already in the possession of the majority of surgeons in training. Technology in the palm of our hands has led to a revolution of accessible information for the plastic surgery trainee and surgeon. This article reviews the uses of smartphones and applications for plastic surgeons in education, telemedicine and global health. A comprehensive guide to existing and upcoming learning materials and clinical tools for the plastic surgeon is included. E-books, podcasts, educational videos, guidelines, work-based assessment tools and online logbooks are presented. In the limited resource setting of modern clinical practice, savvy plastic surgeons can select technological tools to democratise access to education and best clinical care. Copyright © 2013 British Association of Plastic, Reconstructive and Aesthetic Surgeons. Published by Elsevier Ltd. All rights reserved.

  18. D-piece modifications of the hemiasterlin analog HTI-286 produce potent tubulin inhibitors.

    Science.gov (United States)

    Zask, Arie; Birnberg, Gary; Cheung, Katherine; Kaplan, Joshua; Niu, Chuan; Norton, Emily; Yamashita, Ayako; Beyer, Carl; Krishnamurthy, Girija; Greenberger, Lee M; Loganzo, Frank; Ayral-Kaloustian, Semiramis

    2004-08-16

    Modifications of the D-piece carboxylic acid group of the hemiasterlin analog HTI-286 gave tubulin inhibitors which were potent cytotoxic agents in taxol resistant cell lines expressing P-glycoprotein. Amides derived from proline had potency comparable to HTI-286. Reduction of the carboxylic acid to ketones and alcohols or its conversion to acidic heterocycles also gave potent analogs. Synthetic modifications of the carboxylic acid could be carried out selectively using a wide range of synthetic reagents. Proline analog 3 was found to be effective in a human xenograft model in athymic mice.

  19. A new and simple extraction technique for rectal foreign bodies: removing by cutting into small pieces

    OpenAIRE

    Abbas Aras; Mehmet Karabulut; Osman Kones; Kaplan Baha Temizgonul; Halil Alis

    2014-01-01

    The purposes of insertion and types of foreign bodies in rectum show great variation. Rectal foreign bodies need to be removed without giving damage to intestinal wall and this should be done in the easiest possible way. We have reported a new and a simple technique. It is easy to apply and safe. A patient was admitted to our clinic with a rectal foreign body (radish) which was successfully removed by cutting it into small pieces. We conclude that different kinds of rectal foreign bodies, esp...

  20. Modified snap-on attachment with ′O-ring′ for two piece hollow bulb obturator

    Directory of Open Access Journals (Sweden)

    C Gunasekar

    2013-01-01

    Full Text Available Restoration of near normal functions in patients who have been treated with hemimaxillectomy is generally difficult, in view of the restriction in mouth opening following healing of large surgical wound. Further, the extent and nature of the surgical defect differ from patient to patient. Thus, design of an obturator needs to be patient oriented. In this report, we describe a novel snap-on attachment with O-ring in a conventional two piece hollow bulb obturator for a 70-year-old male treated for carcinoma of the left maxilla and sinus.

  1. Patient’s satisfaction after 2-piece inflatable penile prosthesis implantation: An Italian multicentric study

    Directory of Open Access Journals (Sweden)

    Giorgio Gentile

    2016-03-01

    Full Text Available Introduction: Penile prosthesis implant represents a valuable solution for pts with severe erectile dysfunction (ED, non-responders to medical management. The aim of our study was to evaluate the satisfaction of patients (pts after 2-pieces inflatable penile prosthesis (IPP. Aim of the study: to evaluate safety, reliability and post-operative patient’s satisfaction after implantation of two-pieces IPP. Materials and Methods: This retrospective multicentric analysis concerns a group of 42 patients undergone 2-pieces IPP implantation from November 2005 to November 2013, in four Centers of proven experience. As a first step, a detailed review of all clinical reports was performed. Secondly, every patient was asked to fill the Erectile Dysfunction Inventory of Treatment Satisfaction (EDITS specifically modified, in order to assess their own satisfaction after surgery and, its impact on patient’s quality of sexual life. Results: 42 pts were evaluated (AMS-Ambicor: 28; Coloplast- Excell: 14; mean age, at time of operation: 60,7 years; mean follow up: 27,6 months; etiology of ED: vascular 23,8%, diabetes 19%, La Peyronie D. 7,1%, consequence of radical prostatectomy 31%, consequence of other pelvic surgery 11,9%, spinal trauma 7%. Mean operative time: 117 ± 58 min, mean postoperative hospital stay 3 ± 1,6 days. Post operative short-term complications: 4 pts (9,5%. Post operative long-term complications: 4 pts (9,5%. Long-term functional results (Questionnaire: 71% of pts (30 reported regular use of the prosthesis, at least 1 time/week, the satisfaction was good in 42% of pts (18, quite good in 33,3% (14, quite bad in 2,4% (1, very bad in 7,1% (3, 6 pts (14,4% didn’t answer. Conclusions: 2 pieces IPP appears to be associated with a low complication rate and good satisfaction of pts especially in the elderly. It also assures satisfactory rates of aesthetics and functional results.

  2. The Arrangement for My Funny Valentine by Marco Pereira: Leadsheet to Piece

    Directory of Open Access Journals (Sweden)

    Rafael Thomaz

    2013-05-01

    Full Text Available his article presents an analysis of the arrangement made by the Brazilian guitarist Marco Pereira for the American song My Funny Valentine in order to explore and understand the transformation of an open structured theme of a popular song into a closed structured piece for a solo instrument. For this purpose, a brief history of the hybridization of Brazilian music was outlined emphasizing solo guitar and an approach to the specific aspects and potential of using the leadsheet and conventional score.

  3. Tourism at Risk: Failures and Dichotomies of Risk Perception Theory in Tourism (Opinion Piece

    Directory of Open Access Journals (Sweden)

    Maximiliano E. KORSTANJE

    2017-12-01

    Full Text Available The turn of the century has brought a lot of radical shifts and risks for tourism industry, which ranged from terrorism to lethal virus outbreaks. Henceforth risk perception theory, which was formulated in psychology, was re-appropriated by policy makers and tourism-related scholars. However, from its inception this conceptual corpus was based on the economic-centred paradigm. This piece discusses critically the main limitations of risk perception theory and the rise of a new discipline, post disaster marketing, in view of the caveats and speculative assumption of “the precautionary principle”.

  4. A new mask to prevent environmental contamination during radio aerosol mouth-piece inhalation procedures

    International Nuclear Information System (INIS)

    Braga, Francisco Jose Hossri Nogueira.

    1994-01-01

    Environmental contamination is frequent during labelled aerosol mouth-piece inhalation procedures. Previous personnel data showed that in 18/18 situations air background activity has increased after inhalation and this may create serious routine and economical problems. We have tested a new adherent mask made of 3 M's TEGADERM in sixty 99 m Tc-DTPA inhalation studies and the results indicates that the use of such a mask may eliminate the problem of environmental contamination. The device is useful but not entirely efficient in cases when good skin adherence cannot be obtained. 48 refs, 10 figs, 2 tabs

  5. PuzzleArt Therapy: Connecting the Pieces in Search of Answers

    Directory of Open Access Journals (Sweden)

    Jennifer Fortuna

    2016-10-01

    Full Text Available Alli Berman, a New York based artist, provided the cover art for the Fall 2016 issue of The Open Journal of Occupational Therapy (OJOT. “Sunlight Underwater” is a 12 piece PuzzleArt painting made from acrylic on American maple that measures 22x30. The PuzzleArt concept began as a simple exercise that evolved into a therapeutic modality. When a sudden stroke impacted Berman’s well-being and quality of life, it was art that helped her to make connections during recovery.

  6. Improved Nyquist Pulses Produced By A Filter with Senary Piece-wise Polynomial Frequency Characteristic

    Directory of Open Access Journals (Sweden)

    BALAN, A. L.

    2014-05-01

    Full Text Available A novel family of inter-symbol interference (ISI free pulses generated by improved Nyquist filters with a frequency characteristic composed of six parabolic pieces is proposed. We studied the performance of the new pulses in terms of the ISI error probability when the impulse response is sampled with a timing offset. To illustrate the achieved improvement, the new pulses are compared with other performing pulses that were reported in the literature. Simulation results show that comparable or enhanced ISI performance can be obtained at reasonable complexity.

  7. Telecommunications and internet broadband policy: sorting out the pieces for telerehabilitation.

    Science.gov (United States)

    Seelman, Katherine D

    2010-01-01

    Technological change is accelerating and with it regulatory upheaval. Most of us agree that providing universal telecommunication services to all our citizens is a worthy ideal. Nonetheless, many of us do not agree that regulation should be the means to make broadband Internet services widely available. This Viewpoint begins sorting out pieces of the emerging United States, regulatory and policy puzzle for broadband Internet with an eye to the interests of telerehabilitation providers and consumers. Just how might changes in legal authority, regulation and agency jurisdictions impact us?

  8. Comparison of thorough decontamination techniques on dismantled pieces of a PWR reactor

    International Nuclear Information System (INIS)

    Klein, M.; Rahier, A.; Mandoki, R.; Ponnet, M.

    1998-01-01

    The decontamination experience gained during the BR3 dismantling project is developed. This started with the full system decontamination of the primary loop and was followed by R and D on thorough decontamination projects. First, a wet abrasive installation has been installed and is now in operation for the thorough cleaning of metallic pieces of simple geometry. Afterwards, the chemical cerium process has been developed. The results of the regeneration with ozone and with electrochemistry are presented in detail. The ozone regeneration process has been selected for the industrial installation of which the construction is foreseen in 1998. (author)

  9. Nilai Pendidikan Dalam Komik One Piece Jilid 1-23 Karya Eiichiro Oda (Sebuah Tinjauan Sosiologi Sastra)

    OpenAIRE

    Furqon, Muhammad Taufiq

    2013-01-01

    Furqon, Muhammad Taufiq. 2013. “Nilai Pendidikan dalam Komik One Piece Jilid 1-23 Karya Eiichiro Oda”. Skripsi S-1 Fakultas Ilmu Budaya Universitas Diponegoro Semarang. Permasalahan dalam penelitian ini adalah komik One Piece dilihat dari bentuknya hanya terdiri dari gambar dan teks, tetapi ada unsur-unsur fiksi terdapat di dalamnya seperti adanya tema, tokoh, latar,dan ada amanat yang ingin disampaikan pengarangnya. Sehingga pemahaman dan pemaknaan terhadapnya mampu memberikan manfaat bagi p...

  10. Physico-chemical properties of excavated plastic from landfill mining and current recycling routes.

    Science.gov (United States)

    Canopoli, L; Fidalgo, B; Coulon, F; Wagland, S T

    2018-06-01

    In Europe over 5.25 billion tonnes of waste has been landfilled between 1995 and 2015. Among this large amount of waste, plastic represents typically 5-25 wt% which is significant and has the potential to be recycled and reintroduced into the circular economy. To date there is still however little information available of the opportunities and challenges in recovering plastics from landfill sites. In this review, the impacts of landfill chemistry on the degradation and/or contamination of excavated plastic waste are analysed. The feasibility of using excavated plastic waste as feedstock for upcycling to valuable chemicals or liquid fuels through thermochemical conversion is also critically discussed. The limited degradation that is experienced by many plastics in landfills (>20 years) which guarantee that large amount is still available is largely due to thermooxidative degradation and the anaerobic conditions. However, excavated plastic waste cannot be conventionally recycled due to high level of ash, impurities and heavy metals. Recent studies demonstrated that pyrolysis offers a cost effective alternative option to conventional recycling. The produced pyrolysis oil is expected to have similar characteristics to petroleum diesel oil. The production of valuable product from excavated plastic waste will also increase the feasibility of enhanced landfill mining projects. However, further studies are needed to investigate the uncertainties about the contamination level and degradation of excavated plastic waste and address their viability for being processed through pyrolysis. Copyright © 2018 Elsevier Ltd. All rights reserved.

  11. Exercise and plasticize the brain

    DEFF Research Database (Denmark)

    Mala, Hana; Wilms, Inge

    Neuroscientific studies continue to shed light on brain’s plasticity and its innate mechanisms to recover. The recovery process includes re-wiring of the existing circuitry, establishment of new connections, and recruitment of peri-lesional and homologous areas in the opposite hemisphere....... The plasticity of the brain can be stimulated and enhanced through training, which serves as a fundamental element of neurorehabilitative strategies. For instance, intensive cognitive and physical training promote the activation of processes that may help the brain to adapt to new conditions and needs. However...... neurorehabilitation is to understand and define how to stimulate the injured brain to elicit the desired adaptation. Research focuses on uncovering specific elements relevant for training planning and execution in order to create an environment that stimulates and maximizes the exploitation of the brain’s plastic...

  12. Surface properties of beached plastics.

    Science.gov (United States)

    Fotopoulou, Kalliopi N; Karapanagioti, Hrissi K

    2015-07-01

    Studying plastic characteristics in the marine environment is important to better understand interaction between plastics and the environment. In the present study, high-density polyethylene (HDPE), polyethylene terephalate (PET), and polyvinyl chloride (PVC) samples were collected from the coastal environment in order to study their surface properties. Surface properties such as surface functional groups, surface topography, point of zero charge, and color change are important factors that change during degradation. Eroded HDPE demonstrated an altered surface topography and color and new functional groups. Eroded PET surface was uneven, yellow, and occasionally, colonized by microbes. A decrease in Fourier transform infrared (FTIR) peaks was observed for eroded PET suggesting that degradation had occurred. For eroded PVC, its surface became more lamellar and a new FTIR peak was observed. These surface properties were obtained due to degradation and could be used to explain the interaction between plastics, microbes, and pollutants.

  13. The Prism Plastic Calorimeter (PPC)

    CERN Multimedia

    2002-01-01

    This proposal supports two goals: \\\\ \\\\ First goal:~~Demonstrate that current, widely used plastic technologies allow to design Prism Plastic Calorimeter~(PPC) towers with a new ``liquid crystal'' type plastic called Vectra. It will be shown that this technique meets the requirements for a LHC calorimeter with warm liquids: safety, hermeticity, hadronic compensation, resolution and time response. \\\\ \\\\ Second goal:~~Describe how one can design a warm liquid calorimeter integrated into a LHC detector and to list the advantages of the PPC: low price, minimum of mechanical structures, minimum of dead space, easiness of mechanical assembly, accessibility to the electronics, possibility to recirculate the liquid. The absorber and the electronic being outside of the liquid and easily accessible, one has maximum flexibility to define them. \\\\ \\\\ The R&D program, we define here aims at showing the feasibility of these new ideas by building nine towers of twenty gaps and exposing them to electron and hadron beams.

  14. Plastic solidification of radioactive wastes

    International Nuclear Information System (INIS)

    Moriyama, Noboru

    1981-01-01

    Over 20 years have elapsed after the start of nuclear power development, and the nuclear power generation in Japan now exceeds the level of 10,000 MW. In order to meet the energy demands, the problem of the treatment and disposal of radioactive wastes produced in nuclear power stations must be solved. The purpose of the plastic solidification of such wastes is to immobilize the contained radionuclides, same as other solidification methods, to provide the first barrier against their move into the environment. The following matters are described: the nuclear power generation in Japan, the radioactive wastes from LWR plants, the position of plastic solidification, the status of plastic solidification in overseas countries and in Japan, the solidification process for radioactive wastes with polyethylene, and the properties of solidified products, and the leachability of radionuclides in asphalt solids. (J.P.N.)

  15. Constraints on the evolution of phenotypic plasticity

    DEFF Research Database (Denmark)

    Murren, Courtney J; Auld, Josh R.; Callahan, Hilary S

    2015-01-01

    Phenotypic plasticity is ubiquitous and generally regarded as a key mechanism for enabling organisms to survive in the face of environmental change. Because no organism is infinitely or ideally plastic, theory suggests that there must be limits (for example, the lack of ability to produce...... an optimal trait) to the evolution of phenotypic plasticity, or that plasticity may have inherent significant costs. Yet numerous experimental studies have not detected widespread costs. Explicitly differentiating plasticity costs from phenotype costs, we re-evaluate fundamental questions of the limits...... to the evolution of plasticity and of generalists vs specialists. We advocate for the view that relaxed selection and variable selection intensities are likely more important constraints to the evolution of plasticity than the costs of plasticity. Some forms of plasticity, such as learning, may be inherently...

  16. Distribution and biological implications of plastic pollution on the fringing reef of Mo’orea, French Polynesia

    Directory of Open Access Journals (Sweden)

    Elizabeth J. Connors

    2017-08-01

    Full Text Available Coral reef ecosystems of the South Pacific are extremely vulnerable to plastic pollution from oceanic gyres and land-based sources. To describe the extent and impact of plastic pollution, the distribution of both macro- (>5 mm and microplastic (plastic < 5 mm of the fringing reef of an isolated South Pacific island, Mo’orea, French Polynesia was quantified. Macroplastic was found on every beach on the island that was surveyed. The distribution of this plastic was categorized by site type and by the presence of Turbinaria ornata, a common macroalgae on Mo’orea. Microplastics were discovered in the water column of the fringing reef of the island, at a concentration of 0.74 pieces m−2. Additionally, this study reports for the first time the ingestion of microplastic by the corallimorpha Discosoma nummiforme. Microplastics were made available to corallimorph polyps in a laboratory setting over the course of 108 h. Positively and negatively buoyant microplastics were ingested, and a microplastic particle that was not experimentally introduced was also discovered in the stomach cavity of one organism. This study indicates that plastic pollution has the potential to negatively impact coral reef ecosystems of the South Pacific, and warrants further study to explore the broader potential impacts of plastic pollution on coral reef ecosystems.

  17. Distribution and biological implications of plastic pollution on the fringing reef of Mo'orea, French Polynesia.

    Science.gov (United States)

    Connors, Elizabeth J

    2017-01-01

    Coral reef ecosystems of the South Pacific are extremely vulnerable to plastic pollution from oceanic gyres and land-based sources. To describe the extent and impact of plastic pollution, the distribution of both macro- (>5 mm) and microplastic (plastic plastic was categorized by site type and by the presence of Turbinaria ornata, a common macroalgae on Mo'orea. Microplastics were discovered in the water column of the fringing reef of the island, at a concentration of 0.74 pieces m -2 . Additionally, this study reports for the first time the ingestion of microplastic by the corallimorpha Discosoma nummiforme. Microplastics were made available to corallimorph polyps in a laboratory setting over the course of 108 h. Positively and negatively buoyant microplastics were ingested, and a microplastic particle that was not experimentally introduced was also discovered in the stomach cavity of one organism. This study indicates that plastic pollution has the potential to negatively impact coral reef ecosystems of the South Pacific, and warrants further study to explore the broader potential impacts of plastic pollution on coral reef ecosystems.

  18. Distribution and biological implications of plastic pollution on the fringing reef of Mo’orea, French Polynesia

    Science.gov (United States)

    2017-01-01

    Coral reef ecosystems of the South Pacific are extremely vulnerable to plastic pollution from oceanic gyres and land-based sources. To describe the extent and impact of plastic pollution, the distribution of both macro- (>5 mm) and microplastic (plastic plastic was categorized by site type and by the presence of Turbinaria ornata, a common macroalgae on Mo’orea. Microplastics were discovered in the water column of the fringing reef of the island, at a concentration of 0.74 pieces m−2. Additionally, this study reports for the first time the ingestion of microplastic by the corallimorpha Discosoma nummiforme. Microplastics were made available to corallimorph polyps in a laboratory setting over the course of 108 h. Positively and negatively buoyant microplastics were ingested, and a microplastic particle that was not experimentally introduced was also discovered in the stomach cavity of one organism. This study indicates that plastic pollution has the potential to negatively impact coral reef ecosystems of the South Pacific, and warrants further study to explore the broader potential impacts of plastic pollution on coral reef ecosystems. PMID:28875079

  19. Asymptotic techniques in elastic-plastic analysis of structures

    International Nuclear Information System (INIS)

    Sayir, M.

    1983-01-01

    Elastic-plastic structures can nowadays be analyzed with the powerful numerical procedures of the finite element method. Nevertheless, in many engineering applications, analytical expressions capable of predicting with sufficient accuracy the stress distributions, the extent of the plastic zones and the load displacement behaviour could be of great practical value. For simple structures and loading stages not too far from the elastic limit, such analytical expressions may be obtained by using perturbation methods and asymptotic expansions. A small dimensionless parameter epsilon is defined as the ratio of a length characterizing the extent of the narrow plastic zone, to a conveniently chosen typical dimension of the structure. Stresses and displacements are formally expanded as asymptotic series in terms of powers of epsilon. For each order of magnitude, the exact basic relations lead to a separate set of simplified differential equations which can be integrated analytically or numerically by using standard procedures. The method is very general and can be applied to several classes of plastic behaviour and of structural problems. Three examples of very simple structures are chosen in particular to illustrate the applicability of the perturbation method to engineering problems. (orig./RW)

  20. Hydrogen-Induced Plastic Deformation in ZnO

    Science.gov (United States)

    Lukáč, F.; Čížek, J.; Vlček, M.; Procházka, I.; Anwand, W.; Brauer, G.; Traeger, F.; Rogalla, D.; Becker, H.-W.

    In the present work hydrothermally grown ZnO single crystals covered with Pd over-layer were electrochemically loaded with hydrogen and the influence of hydrogen on ZnO micro structure was investigated by positron annihilation spectroscopy (PAS). Nuclear reaction analysis (NRA) was employed for determination of depth profile of hydrogen concentration in the sample. NRA measurements confirmed that a substantial amount of hydrogen was introduced into ZnO by electrochemical charging. The bulk hydrogen concentration in ZnO determined by NRA agrees well with the concentration estimated from the transported charge using the Faraday's law. Moreover, a subsurface region with enhanced hydrogen concentration was found in the loaded crystals. Slow positron implantation spectroscopy (SPIS) investigations of hydrogen-loaded crystal revealed enhanced concentration of defects in the subsurface region. This testifies hydrogen-induced plastic deformation of the loaded crystal. Absorbed hydrogen causes a significant lattice expansion. At low hydrogen concentrations this expansion is accommodated by elastic straining, but at higher concentrations hydrogen-induced stress exceeds the yield stress in ZnO and plastic deformation of the loaded crystal takes place. Enhanced hydrogen concentration detected in the subsurface region by NRA is, therefore, due to excess hydrogen trapped at open volume defects introduced by plastic deformation. Moreover, it was found that hydrogen-induced plastic deformation in the subsurface layer leads to typical surface modification: formation of hexagonal shape pyramids on the surface due to hydrogen-induced slip in the [0001] direction.

  1. Project Muskan : Social responsibility of the plastic surgeon

    Directory of Open Access Journals (Sweden)

    Bhatt Yogesh

    2008-01-01

    Full Text Available Although exact statistics are not available, Indian plastic surgeons see around 7,00,000-8,00,000 burn admissions annually with around 10,00,000 cleft patients yet to be operated. In spite of this voluminous load, India does not have national health programs for the various deformities Indian plastic surgeons typically treat. As Plastic Surgeons, it is our social responsibility to treat these patients and bring ′ muskan ′ (smile in Hindi back into their lives. Project Muskan was initiated as an innovative model for targeting these patients and is probably one of its kind in the field of plastic surgery in our country. It is unique because it is a perfect collaboration of government institutions, a Non Government Organization (NGO, and cooperative sectors providing free health care at the doorstep. Identification of the patients was done with the help of the extensive milk dairy network in the state of Gujarat. Provision of transport and other facilities was done by the NGOs and quality health care provision was taken care of by the government hospital. Project Muskan started from a single village but now covers around 3000 villages and tribal areas of Gujarat. It is a system that can be easily reproducible in all hospitals and has reestablished the faith of the common man in government institutes.

  2. Plasticity Theory of Fillet Welds

    DEFF Research Database (Denmark)

    Hansen, Thomas

    2005-01-01

    a safe and statically admissible stress distribution is established. The plasticity solutions are compared with tests carried out at the Engineering Academy of Denmark, Lyngby, in the early nineties, and old fillet weld tests. The new failure conditions are in very good agreement with the yield load......This paper deals with simple methods for calculation of fillet welds based on the theory of plasticity. In developing the solutions the lower-bound theorem is used. The welding material and parts of the base material are subdivided into triangular regions with homogeneous stress fields; thereby...... tests, but not so good agreement with the old failure load tests....

  3. The Plastic Tension Field Method

    DEFF Research Database (Denmark)

    Hansen, Thomas

    2005-01-01

    This paper describes a calculation method for steel plate girders with transverse web stiffeners subjected to shear. It may be used for predicting the failure load or, as a design method, to determine the optimal amount of internal web stiffeners. The new method is called the plastic tension field...... method. The method is based on the theory of plasticity and is analogous to the so-called diagonal compression field method developed for reinforced concrete beams with transverse stirrups, which is adopted in the common European concrete code (Eurocode 2). Many other theories have been developed...

  4. Preparation of coloured wood plastics

    International Nuclear Information System (INIS)

    Lebedev, V.T.; Filippova, T.G.; Rajchuk, F.Z.

    1977-01-01

    A study has been made into the possibility of using fat, as well as alcohol- and water-soluble dyes for radiation-chemical dying of polymers and plastics filled with wood. The use of fat-soluble azo and anthraquinone dyes permits obtaining intensely colored wood-plastic materials based on methyl methacrylate by way of gamma radiation with doses of up to 3 Mrad. At a dose above 5 Mrad, a marked tarnishing of the dye or a change in color and stains are observed. Dyes in styrene withstand higher radiation doses without any significant destruction

  5. Archaeology of Chilean pre-hispanic pieces using induced x-ray fluorescence

    Energy Technology Data Exchange (ETDEWEB)

    Morales, J.R.; Dinator, M.I. [Universidad de Chile, Facultad de Ciencias, Santiago (Chile); Tellez, F. [Universidad Catolica del Norte, I.I.A. San Pedro de Atacama (Chile)

    2001-09-01

    Full text: One of the most famous archaeological sites of Chile is San Pedro de Atacama in the north Andean highlands. The site, 68.23 W, 22.89 S, is close to the border lines with Argentina and Bolivia and was occupied by different cultures in the past like Atacameos and lately by Incas in s. X V. About a century later Hispanic explorers visited the zone. The area is rich in tombs and remains. Due to the abundance of minerals, metallurgy was practiced by pre-Hispanic cultures. This work is part of a study concerning the characterization of metallic artifacts found in several excavations. The elemental composition can help in determining the provenance of the pieces, and the metallurgical techniques used. A set of twenty pieces including hatchets, knifes, chisels, maces and bells were analyzed by X ray fluorescence induced by photons of 59.5 keV provided by a source of Am-241. Detection of Mn, Fe, Ni, Cu, As, Zr, Ag, Sn, Sb, Ba, and Pb has allowed determination of their provenance. (Author)

  6. On Limitations of the Ultrasonic Characterization of Pieces Manufactured with Highly Attenuating Materials

    Science.gov (United States)

    Ramos, A.; Moreno, E.; Rubio, B.; Calas, H.; Galarza, N.; Rubio, J.; Diez, L.; Castellanos, L.; Gómez, T.

    Some technical aspects of two Spanish cooperation projects, funded by DPI and Innpacto Programs of the R&D National Plan, are discussed. The objective is to analyze the common belief about than the ultrasonic testing in MHz range is not a tool utilizable to detect internal flaws in highly attenuating pieces made of coarse-grained steel. In fact high-strength steels, used in some safe industrial infrastructures of energy & transport sectors, are difficult to be inspected using the conventional "state of the art" in ultrasonic technology, due to their internal microstructures are very attenuating and coarse-grained. It is studied if this inspection difficulty could be overcome by finding intense interrogating pulses and advanced signal processing of the acquired echoes. A possible solution would depend on drastically improving signal-to-noise-ratios, by applying new advances on: ultrasonic transduction, HV electronics for intense pulsed driving of the testing probes, and an "ad-hoc" digital processing or focusing of the received noisy signals, in function of each material to be inspected. To attain this challenging aim on robust steel pieces would open the possibility of obtaining improvements in inspecting critical industrial components made of highly attenuating & dispersive materials, as new composites in aeronautic and motorway bridges, or new metallic alloys in nuclear area, where additional testing limitations often appear.

  7. Impact of Fruit Piece Structure in Yogurts on the Dynamics of Aroma Release and Sensory Perception

    Directory of Open Access Journals (Sweden)

    Isabelle Souchon

    2013-05-01

    Full Text Available The aim of this work was to gain insight into the effect of food formulation on aroma release and perception, both of which playing an important role in food appreciation. The quality and quantity of retronasal aroma released during food consumption affect the exposure time of olfactory receptors to aroma stimuli, which can influence nutritional and hedonic characteristics, as well as consumption behaviors. In yogurts, fruit preparation formulation can be a key factor to modulate aroma stimulation. In this context, the impact of size and hardness of fruit pieces in fat-free pear yogurts was studied. Proton Transfer Reaction-Mass Spectrometry (PTR-MS was used to allow sensitive and on-line monitoring of volatile odorous compound release in the breath during consumption. In parallel, a trained panel used sensory profile and Temporal Dominance of Sensations (TDS methods to characterize yogurt sensory properties and their dynamic changes during consumption. Results showed that the size of pear pieces had few effects on aroma release and perception of yogurts, whereas fruit hardness significantly influenced them. Despite the fact that yogurts presented short and similar residence times in the mouth, this study showed that fruit preparation could be an interesting formulation factor to enhance exposure time to stimuli and thus modify food consumption behaviors. These results could be taken into account to formulate new products that integrate both nutritional and sensory criteria.

  8. FEA analysis and design optimization for a multifunctional piece of furniture

    Directory of Open Access Journals (Sweden)

    Haraga Georgeta

    2017-01-01

    Full Text Available The paper presents an original approach to the integration of computer aided design and finite element analysis for a multifunctional piece of furniture using CATIA Generative Structural Analysis workbench. Finite Element Analysis (FEA application is an important engineering technique in the furniture industry. FEA is an accurate method for numerical solution of field problems. A major problem of mesh generation today is access to CAD geometry in a efficient and precise manner. Starting with a solid modelling for the creation of the desired piece of multifunctional furniture is used in this case, the automatic generation of the finite element meshes. Getting more accurate results for the mesh refinement process can be made by changing parameters. The article outlines the developed model for analysing the supporting structure of the armchair. This model provides simulating of the different loads and checking the raised stresses and deformation in the structures analysed. The main objective of this research is to evaluate strength of wooden cedar armchair for a person weighing 140 kg and for this the finite element analysis (FEA has been used. Multifunctional furniture is the answer to the challenges contemporary lifestyle, creativity in design activities that require optimal space utilization and reducing costs.

  9. Low level radioactive waste management in New York State all the pieces of the puzzle, but

    International Nuclear Information System (INIS)

    Gerber, C.A.

    1995-01-01

    Unlike many other states and compacts, New York not only has a volunteer community, but that community has over three thousand acres of state owned land that was intended for commercial nuclear use. A poll conducted by the Siting Commission indicates that the citizens of New York understand the need for a central monitored disposal facility for LLRW. Hundreds of widely dispersed storage sites are unacceptable to the majority of New Yorkers. New York State has a law requiring the siting and construction of a facility for the permanent disposal of LLRW. The regulations are in place and the Siting Commission has gone through the siting process forward, and should be about finished doing it backwards as the amended state law required. The State Health Department has authorized a $800,000 contract to the National Academy of Science to review the process. The representatives of the Cortland County opponents went on record and already stated that the NAS Study is unacceptable. After fifty million dollars the results are catastrophic. The generators in the state will be forced to store their waste because of the failure by the state to obey it's own law. According to the law, the facility was to be in operation no later than January 1, 1993. While New York State has all the pieces of the LLRW management puzzle on the table, there are many people with political and social agendas ready to knock the pieces onto the floor

  10. Bacterial contamination of stethoscope chest pieces and the effect of daily cleaning.

    Science.gov (United States)

    Fujita, H; Hansen, B; Hanel, R

    2013-01-01

    Stethoscopes are a potential source of nosocomial infection for hospitalized humans, a phenomenon not previously studied in companion animals. To determine if daily cleaning of stethoscope chest pieces reduces bacterial contamination between cleanings. Client-owned dogs and cats. Prospective observational study. In phase 1, bacterial cultures were obtained from the chest pieces of 10 participant stethoscopes once weekly for 3 weeks. In phase 2, stethoscopes were cleaned daily and 2 culture samples were obtained once weekly, immediately before and after cleaning with 70% isopropyl alcohol, for 3 weeks. Daily cleaning eliminated bacteria immediately after each cleaning (P = .004), but did not reduce the rate of positive cultures obtained before cleaning in phase 2. Cultures were positive for 20/30 (67%) samples during phase 1 and 18/30 (60%) obtained before daily cleaning during phase 2. Recovered organisms included normal skin flora, agents of opportunistic infections, and potential pathogens. The only genus that was repeatedly recovered from the same stethoscope for 2 or more consecutive weeks was Bacillus sp. Daily cleaning was highly effective at removing bacteria, but provided no reduction in precleaning contamination. Cleaning stethoscopes after use on dogs or cats infected with pathogenic bacteria and before use on immunocompromised animals should be considered. Copyright © 2013 by the American College of Veterinary Internal Medicine.

  11. Archaeology of Chilean pre-hispanic pieces using induced x-ray fluorescence

    International Nuclear Information System (INIS)

    Morales, J.R.; Dinator, M.I.; Tellez, F.

    2001-01-01

    Full text: One of the most famous archaeological sites of Chile is San Pedro de Atacama in the north Andean highlands. The site, 68.23 W, 22.89 S, is close to the border lines with Argentina and Bolivia and was occupied by different cultures in the past like Atacameos and lately by Incas in s. X V. About a century later Hispanic explorers visited the zone. The area is rich in tombs and remains. Due to the abundance of minerals, metallurgy was practiced by pre-Hispanic cultures. This work is part of a study concerning the characterization of metallic artifacts found in several excavations. The elemental composition can help in determining the provenance of the pieces, and the metallurgical techniques used. A set of twenty pieces including hatchets, knifes, chisels, maces and bells were analyzed by X ray fluorescence induced by photons of 59.5 keV provided by a source of Am-241. Detection of Mn, Fe, Ni, Cu, As, Zr, Ag, Sn, Sb, Ba, and Pb has allowed determination of their provenance. (Author)

  12. Mechanical Performance Evaluation of a Top End Piece for Dual Cooled Fuels

    International Nuclear Information System (INIS)

    Kim, Jae Yong; Yoon, Kyung Ho; Kim, Hyung Kyu; Choi, Woo Seok

    2011-01-01

    A fuel assembly consists of five major components, i.e., a top end piece (TEP), a bottom end piece (BEP), spacer grids (SGs), guide tubes (GTs) and an instrumentation tube (IT): in addition, it also includes fuel rods (FRs). The TEP/BEP should satisfy stress intensity limits according to the conditions A and B of ASME, Section III, Division 1.Subsection NB. In a dual-cooled fuel assembly, the array and position of fuel rods are different from those in a conventional PWR fuel assembly; these changes are necessary for achieving power uprating. The flow plates of the TEP and BEP have to be modified accordingly. The pattern and shape of the flow holes were newly designed. To verify the strength compatibility, the Tresca stress limit according to the ASME code was investigated in the case of an axial load of 22.241 kN. In this paper, the stress linearization procedure for strength evaluation of a newly designed TEP is presented

  13. Effect of waste synthetic bag pieces on the CBR value of expansive Soil

    Directory of Open Access Journals (Sweden)

    Ajay Kumar Agarwal

    2015-03-01

    Full Text Available Expansive soils such as black cotton soil which are widely distributed in India have a tendency for volume changes due to change in moisture content. Also exhibits very low bearing capacity and high compressibility. Stabilization of such soil by admixture is used commonly now days. But no mix is suitable to improve all the types of soil. But it is obvious that depending on type of soil & type of admixture the optimum mix can be designed.  In this paper a mix has been designed to improve the bearing capacity of soil by using fly ash and lime mixture, reinforced with waste synthetic bag pieces. Various tests are carried out to determine the CBR value and other soil properties with and without using any admixture and reinforcement. The maximum value of CBR was found to be23.82% for 2.5 mm penetration and 22.21% for 5 mm penetration, when waste synthetic bag pieces of size 2 cm * 2 cm were used at a proportion of 0.1%.

  14. A work criterion for plastic collapse

    International Nuclear Information System (INIS)

    Muscat, Martin; Mackenzie, Donald; Hamilton, Robert

    2003-01-01

    A new criterion for evaluating limit and plastic loads in pressure vessel design by analysis is presented. The proposed criterion is based on the plastic work dissipated in the structure as loading progresses and may be used for structures subject to a single load or a combination of multiple loads. Example analyses show that limit and plastic loads given by the plastic work criterion are robust and consistent. The limit and plastic loads are determined purely by the inelastic response of the structure and are not influenced by the initial elastic response: a problem with some established plastic criteria

  15. Foods Inducing Typical Gastroesophageal Reflux Disease Symptoms in Korea

    OpenAIRE

    Choe, Jung Wan; Joo, Moon Kyung; Kim, Hyo Jung; Lee, Beom Jae; Kim, Ji Hoon; Yeon, Jong Eun; Park, Jong-Jae; Kim, Jae Seon; Byun, Kwan Soo; Bak, Young-Tae

    2017-01-01

    Background/Aims Several specific foods are known to precipitate gastroesophageal reflux disease (GERD) symptoms and GERD patients are usually advised to avoid such foods. However, foods consumed daily are quite variable according to regions, cultures, etc. This study was done to elucidate the food items which induce typical GERD symptoms in Korean patients. Methods One hundred and twenty-six Korean patients with weekly typical GERD symptoms were asked to mark all food items that induced typic...

  16. Thermal Reduction of NOx with Recycled Plastics.

    Science.gov (United States)

    Oluwoye, Ibukun; Dlugogorski, Bogdan Z; Gore, Jeff; Vyazovkin, Sergey; Boyron, Olivier; Altarawneh, Mohammednoor

    2017-07-05

    This study develops technology for mitigation of NO x formed in thermal processes using recycled plastics such as polyethylene (PE). Experiments involve sample characterization, and thermogravimetric decomposition of PE under controlled atmospheres, with NO x concentration relevant to industrial applications. TGA-Fourier transform infrared (FTIR) spectroscopy and NO x chemiluminescence serve to obtain the removal efficiency of NO x by fragments of pyrolyzing PE. Typical NO x removal efficiency amounts to 80%. We apply the isoconversional method to derive the kinetic parameters, and observe an increasing dependency of activation energy on the reaction progress. The activation energies of the process span 135 kJ/mol to 226 kJ/mol, and 188 kJ/mol to 268 kJ/mol, for neat and recycled PE, respectively, and the so-called compensation effect accounts for the natural logarithmic pre-exponential ln (A/min -1 ) factors of ca. 19-35 and 28-41, in the same order, depending on the PE conversion in the experimental interval of between 5 and 95%. The observed delay in thermal events of recycled PE reflects different types of PE in the plastic, as measurements of intrinsic viscosity indicate that, the recycled PE comprises longer linear chains. The present evaluation of isoconversional activation energies affords accurate kinetic modeling of both isothermal and nonisothermal decomposition of PE in NO x -doped atmosphere. Subsequent investigations will focus on the effect of mass transfer and the presence of oxygen, as reburning of NO x in large-scale combustors take place at higher temperatures than those included in the current study.

  17. Mixed-mode elastic-plastic fracture of 2024-T351 aluminium alloy

    International Nuclear Information System (INIS)

    Sakata, Masaru; Aoki, Shigeru; Kishimoto, Kikuo; Chikugo, Hiroshi; Takizawa, Masakazu.

    1985-01-01

    In order to evaluate accurately the strength and structural soundness of the structures made of high toughness materials, it is necessary to clarify the fracture behavior under the loading condition of mixed mode such as oblique cracks as well as the elasto-plastic fracture behavior of the materials in the case of single opening displacement type mode. About the fracture condition in the state of mixed mode, various theories based on the linear fracture mechanics have been proposed. In this study, the elasto-plastic fracture toughness test of mixed mode was carried out by using an aluminum alloy as the subject, and the behavior of dulling and development of cracks was observed with a scanning electron microscope. Moreover, the state of deformation of the test pieces was analyzed by elasto-plastic finite element method, thus the parameters controlling the elasto-plastic fracture of mixed mode were examined. In the range of this study, the limiting stretch zone width in the case of loading of mixed mode was 12 μm similarly to the case of single mode. Also in the case of mixed mode, there was distinct difference between the inclination of a dulling straight line and an R-curve, and the limit value of J intergral was determined by their intersection. (Kako, I.)

  18. Effect of temperature change exerted on plastic deformation of SUS 304

    International Nuclear Information System (INIS)

    Niitsu, Yasushi; Ikegami, Kozo

    1985-01-01

    Under the condition of mechanical load, on which the thermal stress due to temperature change is superposed, the deformation behavior of structural materials is affected by not only loading history but also temperature history. Also at the time of working materials, the case that the relation between plastic deformation and temperature change becomes a problem is not few, such as cold working after hot rolling. In this study, the effect of temperature change exerted on the plastic deformation of SUS 304 stainless steel was examined, as this material has been frequently used as a high temperature structural material. That is, the plastic deformation behavior at a certain temperature after prestrain was applied at a different temperature was experimentally determined under various temperature and load conditions. Moreover, the quantitative evaluation of the results obtained was attempted by using the concept of an equal plastic strain curved surface. The test pieces and the experimental method, the behavior in uniaxial loading and the behavior in combined loading are reported. (Kako, I.)

  19. Body dysmorphia and plastic surgery.

    Science.gov (United States)

    Kyle, Allison

    2012-01-01

    Body dysmorphic disorder is a mental disorder characterized by a preoccupation with some aspect of one's appearance. In cosmetic surgery, this preoccupation can be overlooked by practitioners resulting in a discrepancy between expected and realistic outcome. Identifying the characteristics of this disorder may be crucial to the practitioner-patient relationship in the plastic surgery setting.

  20. Ways of Viewing Pictorial Plasticity

    NARCIS (Netherlands)

    Wijntjes, M.W.A.

    2017-01-01

    The plastic effect is historically used to denote various forms of stereopsis. The vivid impression of depth often associated with binocular stereopsis can also be achieved in other ways, for example, using a synopter. Accounts of this go back over a hundred years. These ways of viewing all aim

  1. Ways of Viewing Pictorial Plasticity

    Directory of Open Access Journals (Sweden)

    Maarten W. A. Wijntjes

    2017-03-01

    Full Text Available The plastic effect is historically used to denote various forms of stereopsis. The vivid impression of depth often associated with binocular stereopsis can also be achieved in other ways, for example, using a synopter. Accounts of this go back over a hundred years. These ways of viewing all aim to diminish sensorial evidence that the picture is physically flat. Although various viewing modes have been proposed in the literature, their effects have never been compared. In the current study, we compared three viewing modes: monocular blur, synoptic viewing, and free viewing (using a placebo synopter. By designing a physical embodiment that was indistinguishable for the three experimental conditions, we kept observers naïve with respect to the differences between them; 197 observers participated in an experiment where the three viewing modes were compared by performing a rating task. Results indicate that synoptic viewing causes the largest plastic effect. Monocular blur scores lower than synoptic viewing but is still rated significantly higher than the baseline conditions. The results strengthen the idea that synoptic viewing is not due to a placebo effect. Furthermore, monocular blur has been verified for the first time as a way of experiencing the plastic effect, although the effect is smaller than synoptic viewing. We discuss the results with respect to the theoretical basis for the plastic effect. We show that current theories are not described with sufficient details to explain the differences we found.

  2. Ways of Viewing Pictorial Plasticity.

    Science.gov (United States)

    Wijntjes, Maarten W A

    2017-01-01

    The plastic effect is historically used to denote various forms of stereopsis. The vivid impression of depth often associated with binocular stereopsis can also be achieved in other ways, for example, using a synopter. Accounts of this go back over a hundred years. These ways of viewing all aim to diminish sensorial evidence that the picture is physically flat. Although various viewing modes have been proposed in the literature, their effects have never been compared. In the current study, we compared three viewing modes: monocular blur, synoptic viewing, and free viewing (using a placebo synopter). By designing a physical embodiment that was indistinguishable for the three experimental conditions, we kept observers naïve with respect to the differences between them; 197 observers participated in an experiment where the three viewing modes were compared by performing a rating task. Results indicate that synoptic viewing causes the largest plastic effect. Monocular blur scores lower than synoptic viewing but is still rated significantly higher than the baseline conditions. The results strengthen the idea that synoptic viewing is not due to a placebo effect. Furthermore, monocular blur has been verified for the first time as a way of experiencing the plastic effect, although the effect is smaller than synoptic viewing. We discuss the results with respect to the theoretical basis for the plastic effect. We show that current theories are not described with sufficient details to explain the differences we found.

  3. Electron beam micromachining of plastics

    Czech Academy of Sciences Publication Activity Database

    Dupák, Libor

    2014-01-01

    Roč. 49, 5-6 (2014), s. 310-314 ISSN 0861-4717 R&D Projects: GA MŠk(CZ) LO1212; GA MŠk ED0017/01/01; GA MŠk EE.2.3.20.0103 Institutional support: RVO:68081731 Keywords : micromachining of plastics * Electron beam Subject RIV: JA - Electronics ; Optoelectronics, Electrical Engineering

  4. Field based plastic contamination sensing

    Science.gov (United States)

    The United States has a long-held reputation of being a dependable source of high quality, contaminant-free cotton. Recently, increased incidence of plastic contamination from sources such as shopping bags, vegetable mulch, surface irrigation tubing, and module covers has threatened the reputation o...

  5. Recycling of plastics in Germany

    International Nuclear Information System (INIS)

    Thienen, N. von; Patel, M.

    1999-01-01

    This article deals with the waste management of post-consumer plastics in Germany and its potential to save fossil fuels and reduce CO 2 emissions. Since most experience is available for packaging, the paper first gives an overview of the legislative background and the material flows for this sector. Then recycling and recovery processes for plastics waste from all sectors are assessed in terms of their contribution to energy saving and CO 2 abatement. Practically all the options studied show a better performance than waste treatment in an average incinerator which has been chosen as the reference case. High ecological benefits can be achieved by mechanical recycling if virgin polymers are substituted. The paper then presents different scenarios for managing plastic waste in Germany in 1995: considerable savings can be made by strongly enhancing the efficiency of waste incinerators. Under these conditions the distribution of plastics waste among mechanical recycling, feedstock recycling and energy recovery has a comparatively mall impact on the overall results. The maximum savings amount to 74 PJ of energy, i.e, 9% of the chemical sector energy demand in 1995 and 7.0 Mt CO 2 , representing 13% of the sector's emissions. The assessment does not support a general recommendation of energy recovery due to the large difference between the German average and the best available municipal waste-to-energy facilities and also due to new technological developments in the field of mechanical recycling

  6. Transformation plasticity and hot pressing

    International Nuclear Information System (INIS)

    Chaklader, A.C.D.

    1975-01-01

    The transformation plasticity during the phase transition of quartz to cristobalite, monoclinic reversible tetragonal of zirconia, metakaolin to a spinel phase, and brucite to periclase was investigated by studying their compaction characteristics. Viscous flow was found to be the predominant mechanism of mass transport (after an initial particle rearrangement stage) in the case of quartz to cristobalite phase change where the transformation was associated with the formation of an intermediate amorphous silica phase. The results on the monoclinic reversible tetragonal transformation of zirconia indicated that it is most likely controlled by internal strain induced by the stress associated with the volume change (ΔV/V) and the flow stress of the weaker phase. Particle movement and deformation of the weaker phase (possibly tetragonal) may be the manifestation of this plasticity. The plasticity in the case of metakaolin to a spinel phase appeared to start before the exothermic reaction (generally encountered in a dta plot) and may be diffusion controlled. The plasticity encountered during brucite to periclase transformation may be the combined effect of disintegration of precursor particles, vapor-phase lubrication and some deformability of freshly formed very fine MgO particles

  7. Emotion Processing by ERP Combined with Development and Plasticity

    Science.gov (United States)

    2017-01-01

    Emotions important for survival and social interaction have received wide and deep investigations. The application of the fMRI technique into emotion processing has obtained overwhelming achievements with respect to the localization of emotion processes. The ERP method, which possesses highly temporal resolution compared to fMRI, can be employed to investigate the time course of emotion processing. The emotional modulation of the ERP component has been verified across numerous researches. Emotions, described as dynamically developing along with the growing age, have the possibility to be enhanced through learning (or training) or to be damaged due to disturbances in growth, which is underlain by the neural plasticity of emotion-relevant nervous systems. And mood disorders with typical symptoms of emotion discordance probably have been caused by the dysfunctional neural plasticity. PMID:28831313

  8. Suffocation caused by plastic wrap covering the face combined with nitrous oxide inhalation.

    Science.gov (United States)

    Leth, Peter Mygind; Astrup, Birgitte Schmidt

    2017-09-01

    Suicide using a combination of a plastic bag over the head and inhalation of a non-irritating gas, such as helium, argon or nitrogen, has been reported in the literature. Here an unusual suicide method in a 17-year old man by suffocation from covering the face with household plastic wrap, combined with nitrous oxide inhalation, is presented. The case was reviewed based on police, autopsy and hospital reports. A PubMed search for scientific literature related to nitrous oxide abuse and suicide by suffocation was performed and our findings discussed in relation to the scientific literature found. The deceased was a 17-year old man who was found with the nose and mouth closed with a piece of kitchen plastic wrap. The plastic wrap had been removed prior to autopsy. Autopsy findings were suggestive of asphyxia, but were otherwise negative. Nitrous oxide was detected in the brain and lung tissue with headspace-gas chromatography-mass spectrometry (headspace-GCMS). The cause of death was assumed to be suffocation caused by plastic wrap covering the face, combined with nitrous oxide inhalation. Suicide was suspected because of a history of depression for several months. Nitrous oxide, also known as laughing gas, has a euphoric effect and is used as a recreational inhalant drug that can be purchased legally. Deaths caused by recreational nitrous oxide abuse are rare but may occur if used in combination with a plastic bag over the head. This is the first report of suicide by suffocation by external obstruction combined with nitrous oxide inhalation.

  9. Numerical Modeling of the Work Piece Region in the Plasma Arc Cutting Process

    Science.gov (United States)

    Osterhouse, David

    The plasma arc cutting process is widely used for the cutting of metals. The process, however, is not fully understood and further understanding will lead to further improvements. This work aims to elucidate the fundamental physical phenomena in the region where the plasma interacts with the work piece through the use of numerical modeling techniques. This model follows standard computational fluid dynamic methods that have been suitably modified to include plasma effects, assuming either local thermodynamic equilibrium or a slight non-equilibrium captured by the two-temperature assumption. This is implemented in the general purpose, open source CFD package, OpenFOAM. The model is applied to a plasma flow through a geometry that extends from inside the plasma torch to the bottom of the slot cut in the work piece. The shape of the kerf is taken from experimental measurements. The results of this model include the temperature, velocity, and electrical current distribution throughout the plasma. From this, the heat flux to and drag force on the work piece are calculated. The location of the arc attachment in the cut slot is also noted because it is a matter of interest in the published literature as well as significantly effecting the dynamics of the heat flux and drag force. The results of this model show that the LTE formulation is not sufficient to capture the physics present due to unphysical fluid dynamic instabilities and numerical problems with the arc attachment. The two-temperature formulation, however, captures a large part of the physics present. Of particular note, it is found that an additional inelastic collision factor is necessary to describe the increased energy transfer between electrons and diatomic molecules, which is widely neglected in published literature. It is also found that inclusion of the oxygen molecular ion is necessary to accurately describe the plasma flow, which has been neglected in all published two-temperature oxygen calculations

  10. Plastics and beaches: A degrading relationship

    International Nuclear Information System (INIS)

    Corcoran, Patricia L.; Biesinger, Mark C.; Grifi, Meriem

    2009-01-01

    Plastic debris in Earth's oceans presents a serious environmental issue because breakdown by chemical weathering and mechanical erosion is minimal at sea. Following deposition on beaches, plastic materials are exposed to UV radiation and physical processes controlled by wind, current, wave and tide action. Plastic particles from Kauai's beaches were sampled to determine relationships between composition, surface textures, and plastics degradation. SEM images indicated that beach plastics feature both mechanically eroded and chemically weathered surface textures. Granular oxidation textures were concentrated along mechanically weakened fractures and along the margins of the more rounded plastic particles. Particles with oxidation textures also produced the most intense peaks in the lower wavenumber region of FTIR spectra. The textural results suggest that plastic debris is particularly conducive to both chemical and mechanical breakdown in beach environments, which cannot be said for plastics in other natural settings on Earth

  11. Toward Modeling Limited Plasticity in Ceramic Materials

    National Research Council Canada - National Science Library

    Grinfeld, Michael; Schoenfeld, Scott E; Wright, Tim W

    2008-01-01

    The characteristic features of many armor-related ceramic materials are the anisotropy on the micro-scale level and the very limited, though non-vanishing, plasticity due to limited number of the planes for plastic slip...

  12. Antireflection coatings on plastics deposited by plasma ...

    Indian Academy of Sciences (India)

    In the ophthalmic industry, plastic lenses are rapidly displacing glass lenses ... Moreover, the plasma polymerization process allows deposition of optical films at room temperature, essential for plastics. ... Bulletin of Materials Science | News.

  13. Mechanical behaviour of nanoparticles: Elasticity and plastic ...

    Indian Academy of Sciences (India)

    2015-06-03

    Jun 3, 2015 ... Mechanical behaviour of nanoparticles: Elasticity and plastic deformation mechanisms ... The main results in terms of elasticity and plastic deformation mechanisms are then reported ... Pramana – Journal of Physics | News.

  14. Concept typicality responses in the semantic memory network.

    Science.gov (United States)

    Santi, Andrea; Raposo, Ana; Frade, Sofia; Marques, J Frederico

    2016-12-01

    For decades concept typicality has been recognized as critical to structuring conceptual knowledge, but only recently has typicality been applied in better understanding the processes engaged by the neurological network underlying semantic memory. This previous work has focused on one region within the network - the Anterior Temporal Lobe (ATL). The ATL responds negatively to concept typicality (i.e., the more atypical the item, the greater the activation in the ATL). To better understand the role of typicality in the entire network, we ran an fMRI study using a category verification task in which concept typicality was manipulated parametrically. We argue that typicality is relevant to both amodal feature integration centers as well as category-specific regions. Both the Inferior Frontal Gyrus (IFG) and ATL demonstrated a negative correlation with typicality, whereas inferior parietal regions showed positive effects. We interpret this in light of functional theories of these regions. Interactions between category and typicality were not observed in regions classically recognized as category-specific, thus, providing an argument against category specific regions, at least with fMRI. Copyright © 2016 Elsevier Ltd. All rights reserved.

  15. 12 CFR 408.6 - Typical classes of action.

    Science.gov (United States)

    2010-01-01

    ... 12 Banks and Banking 4 2010-01-01 2010-01-01 false Typical classes of action. 408.6 Section 408.6 Banks and Banking EXPORT-IMPORT BANK OF THE UNITED STATES PROCEDURES FOR COMPLIANCE WITH THE NATIONAL ENVIRONMENTAL POLICY ACT Eximbank Implementing Procedures § 408.6 Typical classes of action. (a) Section 1507.3...

  16. Recycling plastic bottles in a creative way

    OpenAIRE

    Pavlin, Suzana

    2016-01-01

    Beside other plastic products, plastic bottles represent a true environmental disaster in the last few years. We assume that hardly anyone asks what happens after they drink that last drop of water out of it. Just like most municipal waste, a plastic bottle can be reused, recycled, burned or deposited into landfill. When the Environment Protection Act is not respected, plastic bottle ends up in the nature, very often in the sea, where it decomposes very slowly and has negative influence on th...

  17. Plastic Accumulation in the Mediterranean Sea

    OpenAIRE

    C?zar, Andr?s; Sanz-Mart?n, Marina; Mart?, Elisa; Gonz?lez-Gordillo, J. Ignacio; Ubeda, B?rbara; G?lvez, Jos? ?.; Irigoien, Xabier; Duarte, Carlos M.

    2015-01-01

    Copyright: © 2015 Cózar et al. Concentrations of floating plastic were measured throughout the Mediterranean Sea to assess whether this basin can be regarded as a great accumulation region of plastic debris. We found that the average density of plastic (1 item per 4 m2), as well as its frequency of occurrence (100% of the sites sampled), are comparable to the accumulation zones described for the five subtropical ocean gyres. Plastic debris in the Mediterranean surface waters was dominated by ...

  18. ARE PLASTIC GROCERY BAGS SACKING THE ENVIRONMENT?

    Directory of Open Access Journals (Sweden)

    Mangal Gogte

    2009-12-01

    Full Text Available This paper is oriented on analysis impacts of plastic bags on environment. In this paper is analyzed did plastic bags are so harmful, and what are the main ingredients of it. One part of this paper is oriented on effects of plastic bags and management of their usage. There is also made comparative analysis between impacts of plastic and paper bags on environment.

  19. PLASTIC ANALYSIS OF STEEL FRAME STRUCTURE

    Directory of Open Access Journals (Sweden)

    M. Rogac

    2013-05-01

    Full Text Available This paper presents the plastic analysis of steel frame structure loaded by gravity loads. By applying the cinematic theorem of ultimate analysis, the ultimate load for the case of elastic - ideally plastic material is calculated. The identical structure was treated in the computer program SAP2000 where the zone of material reinforcement in the plastic area was covered. Keywords: Steel frame structure, plastic analysis, ultimate gravity load, material reinforcement.

  20. Design of single piece sabot for a single stage gas gun

    Science.gov (United States)

    Vemparala, Vignesh; Mathew, Arun Tom; Rao Koka, Tirumala

    2017-11-01

    Single piece sabot is a vital part in single stage gas guns for impact testing in aerospace industries. Depending on the type of projectile used the design of sabot varies to accommodate the testing equipment. The velocity of the projectile exiting the barrel is dependent on the material and shape of the sabot used. The material selected for the design of sabot is rigid polyurethane foam, due to their low elastic modulus and low density. Two samples of rigid PU foam is taken and tests are performed to get their exact material properties. These properties are incorporated in numerical simulation to determine the best fit for practical use. Since the PU foams has a wide range of porosity which plays a prominent role in deciding the exit velocity and accuracy of the projectile coming out of the barrel. By optimisation, to the best suitable material sample can be determined.

  1. Influence of use of ultrasound on metallographic structure of plated pieces by welding in ultrasonic field

    Directory of Open Access Journals (Sweden)

    Gh. Amza

    2015-07-01

    Full Text Available To optimize the plating process is necessary to know the behavior of surfaces plated during the exploitation and in particular susceptibility to cracking, the formation of cracks from the inside to outside or reverse, embrittlement in the heat affected zone. Research has been realized considering several samples plated by welding without ultrasonic activation and with ultrasonic activation, and these samples were made of AISI 4130 steel, and as filler material was used Inconel 625 Fe developed as electrode wire ø 1,2 / mm. The plating process was realized by a WIG welding process in Ar100 /% environment with non-consumable tungsten electrode, in two versions, respectively with and without the use of ultrasonic energy. Four pieces played by welding there were analyzed the metallographies structure in the base material, the deposited material and the material from the heat affected zone.

  2. Well-Defined Cyclic Triblock Terpolymers: A Missing Piece of the Morphology Puzzle

    KAUST Repository

    Polymeropoulos, George

    2016-10-27

    Two well-defined cyclic triblock terpolymers, missing pieces of the terpolymer morphology puzzle, consisting of poly(isoprene), polystyrene, and poly(2-vinylpyridine), were synthesized by combining the Glaser coupling reaction with anionic polymerization. An α,ω-dihydroxy linear triblock terpolymer (OH-PI1,4-b-PS-b-P2VP-OH) was first synthesized followed by transformation of the OH to alkyne groups by esterification with pentynoic acid and cyclization by Glaser coupling. The size exclusion chromatography (SEC) trace of the linear terpolymer precursor was shifted to lower elution time after cyclization, indicating the successful synthesis of the cyclic terpolymer. Additionally, the SEC trace of the cyclic terpolymer produced, after cleavage of the ester groups, shifted again practically to the position corresponding to the linear precursor. The first exploratory results on morphology showed the tremendous influence of the cyclic structure on the morphology of terpolymers. © 2016 American Chemical Society.

  3. Numerical simulation of water flow through the bottom en piece of a nuclear fuel assembly

    International Nuclear Information System (INIS)

    Navarro, Moyses A.; Santos, Andre A. Campagnole dos

    2007-01-01

    The water flow through the bottom nozzle of a nuclear fuel assembly was simulated using a commercial CFD code, CFX 10.0. Previously, simulations with a perforated plate similar to the bottom nozzle plate were performed to define the appropriate mesh refinement and turbulence model (κ-ε or SST). Subsequently, the numerical simulation was performed with the optimized mesh using the turbulence model (κ-ε in a standard bottom nozzle with some geometric simplifications. The numerical results were compared with experimental results to determine the pressure drop through the bottom nozzle in the Reynolds range from ∼10500 to ∼95000. The agreement between the numerical simulations and experimental results may be considered satisfactory. The study indicated that the CFD codes can play an important role in the development of pieces with complex geometries, optimizing the planning of the experiments and aiding in the experimental analysis. (author)

  4. Study of the microstructural characteristics of archaeological pieces of pre hispanic green stone

    International Nuclear Information System (INIS)

    Carapia M, L.

    2004-01-01

    The work consists of the following chapters; in the first one information about the meaning, uses and origin of the pre hispanic green stone in the old Mexico are presented, the mineral and chemical characteristics of the green stone and the origin of the pieces in study of the project collection Eduardo Pareyon. In the second chapter the experimental method for the characterization is described and each one of the analysis techniques used for the study of the objects of green stone are also enumerated, as well as the methods of preparation of the samples for the determination of hardness, Analytic Scanning Electron Microscopy, X-ray Fluorescence and the X-ray Diffraction. In the third chapter it is presented and it discusses the information and obtained results of each one of the analysed samples. Finally in the fourth chapter the concreted conclusions are presented in the present work. (Author)

  5. Case study for one-piece removal method of reactor vessel of nuclear ship 'Mutsu'

    International Nuclear Information System (INIS)

    Nagane, Satoru; Kitahara, Katsumi; Yoshikawa, Seiji; Miyasaka, Yasuhiko; Fukumura, Nobuo; Nisizawa, Ichiou

    2010-01-01

    A reactor installed at the center part of the nuclear ship 'Mutsu' has been stored safely and exhibited in a reactor room building since 1996. The reactor vessel and its internals are key components because of main radioactive wastes for the reasonable decommissioning plan in the future. This report describes the one-piece removal method as the one package of the reactor vessel with its internals intact with a shipping container or additional shields. The reactor vessel package (Max.100ton) will be classified acceptable for burial at the low level radioactive waste (LLW), which will be buried at a LLW pit facility under waste disposal regulations. And also, the package will be classified as an IP-2-equivalent package according to the requirement for Shipments and Packagings. (author)

  6. Identifying musical pieces from fMRI data using encoding and decoding models.

    Science.gov (United States)

    Hoefle, Sebastian; Engel, Annerose; Basilio, Rodrigo; Alluri, Vinoo; Toiviainen, Petri; Cagy, Maurício; Moll, Jorge

    2018-02-02

    Encoding models can reveal and decode neural representations in the visual and semantic domains. However, a thorough understanding of how distributed information in auditory cortices and temporal evolution of music contribute to model performance is still lacking in the musical domain. We measured fMRI responses during naturalistic music listening and constructed a two-stage approach that first mapped musical features in auditory cortices and then decoded novel musical pieces. We then probed the influence of stimuli duration (number of time points) and spatial extent (number of voxels) on decoding accuracy. Our approach revealed a linear increase in accuracy with duration and a point of optimal model performance for the spatial extent. We further showed that Shannon entropy is a driving factor, boosting accuracy up to 95% for music with highest information content. These findings provide key insights for future decoding and reconstruction algorithms and open new venues for possible clinical applications.

  7. Quality attributes and color characteristics in three-piece boneless hams.

    Science.gov (United States)

    McKeith, Russell O; Pringle, T Dean

    2013-09-01

    One hundred and fifty hams were selected on visual assessment of quality into normal (C) and two-tone (TT) groups. CIE LAB color and pH measurements were collected at the plant 48h postmortem on the gluteus medius (GM), gluteus profundus (GP), and rectus femoris (RF), and again at 72h on the semimembranosus (SM), biceps femoris (BF), semitendinosus (ST), and RF. Data were analyzed using GLM procedures of SAS, and correlations between color scores, pH, and drip loss were calculated. Plant and fabrication pH were lower (Phams compared with C. Muscles from TT hams had lower (Pcolor and pH are accurate predictors of pork quality attributes in the muscles of a three-piece boneless ham. Copyright © 2013 Elsevier Ltd. All rights reserved.

  8. Analysis of arecoline in Semen Arecae decoction pieces by microchip capillary electrophoresis with contactless conductivity detection

    Directory of Open Access Journals (Sweden)

    Zi-You Cai

    2012-10-01

    Full Text Available A new method for the determination of arecoline in Semen Arecae decoction pieces by microchip capillary electrophoresis with contactless conductivity detection (MCE-CCD was proposed. The effects of various electrophoretic operating parameters on the analysis of arecoline were studied. Under the optimal conditions, arecoline was rapidly separated and detected in 1 min with good linearity over the concentration range of 20–1500 μM (r2=0.9991 and the detection limit of 5 μM (S/N=3. The method was used for the analysis of arecoline satisfactorily with a recovery of 96.8–104%. Keywords: Microchip capillary electrophoresis, Contactless conductivity detection, Arecoline, Semen Arecae

  9. Viewpoint: Telecommunications and Internet Broadband Policy: Sorting Out the Pieces for Telerehabilitation

    Directory of Open Access Journals (Sweden)

    Kate D. Seelman

    2010-09-01

    Full Text Available Technological change is accelerating and with it regulatory upheaval.  Most of us agree that providing universal telecommunication services to all our citizens is a worthy ideal.  Nonetheless, many of us do not agree that regulation should be the means to make broadband Internet services widely available. This Viewpoint begins sorting out pieces of the emerging United States, regulatory and policy puzzle for broadband Internet with an eye to the interests of telerehabilitation providers and consumers. Just how might changes in legal authority, regulation and agency jurisdictions impact us?Key words: telecommunications regulation, telerehabilitation, Federal Communications Commission (FCC, Telecommunications Act of 1996, National Broadband Plan; Comcast vs. FCC; electronic health records (EHR; personal health records (PHR; health information technology (HIT, 

  10. Rheological characterization of plasticized corn proteins for fused deposition modeling

    Science.gov (United States)

    Chaunier, Laurent; Dalgalarrondo, Michèle; Della Valle, Guy; Lourdin, Denis; Marion, Didier; Leroy, Eric

    2017-10-01

    Additive Manufacturing (AM) of tailored natural biopolymer-based objects by Fused Deposition Modeling (FDM) opens new perspectives for applications such as biomedical temporary devices, or pharmaceutical tablets. This exploits the biocompatibility, resorbability and edibility properties of biopolymers. When adequately plasticized, zeins, storage proteins from endosperm of maize kernels, displayed thermomechanical properties possibly matching FDM processing requirements at a convenient temperature Tprinting=130°C. Indeed, with 20% glycerol added (Tg=42°C), plasticized zeins present a high modulus, E'>1GPa, at ambient conditions, which drops below 0.6 MPa at the processing temperature T=130°C, before flowing in the molten state. The rheological characterization shows that the processing window is limited by a progressive increase of viscosity linked to proteins aggregation and crosslinking by S-S bonding between cysteine amino acid residues, which can lead to gelation. However, for short residence time typical of FDM, the viscosity of plasticized zeins is comparable to the one of standard polymers, like ABS or PLA in their FDM processing conditions: indeed, in presence of glycerol, the molten zeins show a shear-thinning behavior with |η*|≈3kPa.s at 1s-1, decreasing to |η*|≈0.3kPa.s at 100s-1, at 130°C. Moreover, zeins presenting both hydrophilic and hydrophobic domains, amphiphilic plasticizers can be used supplementary to tune their rheological behavior. With 20% oleic acid added to the previous composition, the viscosity is divided down to a ratio about 1/2 at 100s-1 at 130°C, below the value of a standard polymer as PLA at its printing temperature. These results show the possible enhancement of the printability of zein-based materials in the molten state, by combining polar and amphiphilic plasticizers.

  11. Thermal homogeneity of plastication processes in single-screw extruders

    Science.gov (United States)

    Bu, L. X.; Agbessi, Y.; Béreaux, Y.; Charmeau, J.-Y.

    2018-05-01

    Single-screw plastication, used in extrusion and in injection moulding, is a major way of processing commodity thermoplastics. During the plastication phase, the polymeric material is melted by the combined effects of shear-induced self-heating (viscous dissipation) and heat conduction coming from the barrel. In injection moulding, a high level of reliability is usually achieved that makes this process ideally suited to mass market production. Nonetheless, process fluctuations still appear that make moulded part quality control an everyday issue. In this work, we used a combined modelling of plastication, throughput calculation and laminar dispersion, to investigate if, and how, thermal fluctuations could propagate along the screw length and affect the melt homogeneity at the end of the metering section. To do this, we used plastication models to relate changes in processing parameters to changes in the plastication length. Moreover, a simple model of throughput calculation is used to relate the screw geometry, the polymer rheology and the processing parameters to get a good estimate of the mass flow rate. Hence, we found that the typical residence time in a single screw is around one tenth of the thermal diffusion time scale. This residence time is too short for the dispersion coefficient to reach a steady state, but too long to be able to neglect radial thermal diffusion and resort to a purely convective solution. Therefore, a full diffusion/convection problem has to be solved with a base flow described by the classic pressure and drag velocity field. Preliminary results already show the major importance of the processing parameters in the breakthrough curve of an arbitrary temperature fluctuation at the end of the metering section of injection moulding screw. When the flow back-pressure is high, the temperature fluctuation is spread more evenly with time, whereas a pressure drop in the flow will results in a breakthrough curve which presents a larger peak of

  12. Study of Reactive Melt Processing Behavior of Externally Plasticized Cellulose Acetate in Presence of Isocyanate

    Directory of Open Access Journals (Sweden)

    Rafael Erdmann

    2014-12-01

    Full Text Available Two types of externally plasticized cellulose acetate (CA were chemically modified using 4,4'-methylene diphenyl diisocyanate (MDI as crosslinking agent. Crosslinking was performed in the molten state by means of melt mixing in an internal mixer. The viscoelastic properties of the non-crosslinked, externally plasticized CA show typical temperature dependence, similar to conventional thermoplastics. A strong increase in storage modulus is observed with increasing crosslink density indicating that the crosslinked compounds exhibit predominately elastic response. The complex viscosity also increases considerably with increasing crosslink density and does not reach the typical Newtonian plateau at low radial frequencies any more. The viscoelastic properties correlate well with the data recorded online during reactive melt processing in the internal mixer. In comparison to the non-crosslinked CA, the crosslinked compounds show higher glass transition temperature, higher VICAT softening temperatures, improved thermal stability and lower plasticizer evaporation at evaluated temperatures.

  13. Functional nanostructures on injection molded plastic

    DEFF Research Database (Denmark)

    Johansson, Alicia Charlotte; Søgaard, Emil; Andersen, Nis Korsgaard

    Nanotechnology can be used to make inexpensive plastic parts with functional surfaces. The plastic parts can be molded using a standard injection molding process. The nanostructures are directly transferred from the surface of the molding tool to the surface of the molded plastic part during...

  14. 7 CFR 58.326 - Plastic cream.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Plastic cream. 58.326 Section 58.326 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards... Material § 58.326 Plastic cream. To produce plastic cream eligible for official certification, the quality...

  15. The evolution of age-dependent plasticity

    NARCIS (Netherlands)

    Fischer, Barbara; van Doorn, G. Sander; Dieckmann, Ulf; Taborsky, Barbara

    2014-01-01

    When organisms encounter environments that are heterogeneous in time, phenotypic plasticity is often favored by selection. The degree of such plasticity can vary during an organism''s lifetime, but the factors promoting differential plastic responses at different ages or life stages remain poorly

  16. Plastic Debris Is a Human Health Issue

    NARCIS (Netherlands)

    Vethaak, A.D.; Leslie, H.A.

    2016-01-01

    The global threat of highly persistent plastic waste accumulating and fragmenting in the world’s oceans, inland waters and terrestrial environments is becoming increasingly evident.1−3 Humans are being exposed to both plastic particles and chemical additives being released from the plastic debris of

  17. [Preliminary study on standardization of production and processing of Angelicae Sinensis Radix pieces].

    Science.gov (United States)

    Nie, Rui-Jie; Wang, Ying-Zi; Sun, Zhen-Yang; Wang, Si-Yu; Zhang, Jing-Zhen

    2017-12-01

    Study on the standardization of Chinese materia medica is an important action for modernization and globalization for traditional Chinese medicine. Standardization on the processing of Chinese herbal pieces is an important part in the study on standardization of Chinese materia medica, so it is of great significance to establish the technical processing standards of Angelicae Sinensis Radix pieces for improving its quality. In this study, single factor experiment was designed to optimize the softening, cutting and drying processes of Angelicae Sinensis Radix. With ferulic acid, Angelicae Sinensis Radix polysaccharide, volatile oil and extracts (water and ethanol) content as the quality index, the effects of different softening, cutting and drying processes on the contents of the five components in Angelicae Sinensis Radix were analyzed, and the normalized distance evaluation method was used to analyze the experimental data. The results showed that the content of five components in Angelicae Sinensis Radix was affected by different softening methods and drying temperature, but the thickness of slice had little effect on the content. The best preparation process for Angelicae Sinensis Radix was as follows: Non-medicinal parts were removed; mildewed and rot as well as moth-eaten parts were removed; washed by the flowing drinking water; stacked in the drug pool; moistening method was used for softening, where 125 mL water was sprayed for every 1 kg of herbs every 2.5 h; upper part of herbs covered with clean and moist cotton, and cut into thin slices (1-2 mm) after 15 h moistening until appropriate softness, with disk thickness of 1-2 cm, then received blast drying for 6 h at 55 ℃, and turned over for 2 times during the drying. Copyright© by the Chinese Pharmaceutical Association.

  18. A case of radiation enteritis with perforated peritonitis caused by a piece of eggshell

    International Nuclear Information System (INIS)

    Kitamura, Hirotaka; Maeda, Kazuya; Miyanaga, Tamonn; Doden, Kenji; Hattori, Masakazu; Hashizume, Yasuo

    2011-01-01

    The patient was a woman in her sixties who had received radiation therapy for cancer of uterine cervix 7 years earlier and had been suffering from diarrhea for these several years. The patient was seen at our emergency clinic because of a 5 hour-history of lower abdominal pain at the beginning of July 2010. An abdominal CT scan showed free air and ascites. A high density structure 1.5 cm in size was identified within the small intestine, but its relation with the perforation was obscure. Emergency operation was done with the most likely diagnosis of intestinal perforation and general peritonitis. When the lower abdomen was opened by midline incision, about 200 ml of cloudy ascites was observed and the ileum became white in color and hard resulting from the radiation therapy. A perforation was identified in the ileum about 15 cm distant from the ileocecal valve, and a 1.5-cm sized thin and hard material was palpated within the intestine at the same portion. Ilececal resection including the perforated portion was performed and functional end-to-end anastomosis was made at a grossly normal area. There was a piece of eggshell 1.5-cm in size in the perforated portion in the resected specimen. From this together with histopathologial findings, perforation of the small intestine caused by a piece of eggshell associated with radiation enteritis was finally diagnosed. Small bowel perforation must be kept in mind as a possible late complication of radiation therapy, however, no cases of small bowel perforation caused by eggshell have been reported so far. This rare case is reported here, with a review of the literature. (author)

  19. A non-linear elastic constitutive framework for replicating plastic deformation in solids.

    Energy Technology Data Exchange (ETDEWEB)

    Roberts, Scott Alan; Schunk, Peter Randall

    2014-02-01

    Ductile metals and other materials typically deform plastically under large applied loads; a behavior most often modeled using plastic deformation constitutive models. However, it is possible to capture some of the key behaviors of plastic deformation using only the framework for nonlinear elastic mechanics. In this paper, we develop a phenomenological, hysteretic, nonlinear elastic constitutive model that captures many of the features expected of a plastic deformation model. This model is based on calculating a secant modulus directly from a materials stress-strain curve. Scalar stress and strain values are obtained in three dimensions by using the von Mises invariants. Hysteresis is incorporated by tracking an additional history variable and assuming an elastic unloading response. This model is demonstrated in both single- and multi-element simulations under varying strain conditions.

  20. One-Piece Zirconia Ceramic versus Titanium Implants in the Jaw and Femur of a Sheep Model: A Pilot Study.

    Science.gov (United States)

    Siddiqi, A; Duncan, W J; De Silva, R K; Zafar, S

    2016-01-01

    Reports have documented titanium (Ti) hypersensitivity after dental implant treatment. Alternative materials have been suggested including zirconia (Zr) ceramics, which have shown predictable osseointegration in animal studies and appear free of immune responses. The aim of the research was to investigate the bone-to-implant contact (BIC) of one-piece Zr, compared with one-piece Ti implants, placed in the jaws and femurs of domestic sheep. Ten New Zealand mixed breed sheep were used. A One-piece prototype Ti (control) and one Zr (test) implant were placed in the mandible, and one of each implant (Ti and Zr) was placed into the femoral epicondyle of each animal. The femur implants were submerged and unloaded; the mandibular implants were placed using a one-stage transgingival protocol and were nonsubmerged. After a healing period of 12 weeks, %BIC was measured. The overall survival rate for mandibular and femur implants combined was 87.5%. %BIC was higher for Zr implants versus Ti implants in the femur (85.5%, versus 78.9%) ( p = 0.002). Zirconia implants in the mandible showed comparable %BIC to titanium implants (72.2%, versus 60.3%) ( p = 0.087). High failure rate of both Zr and Ti one-piece implants in the jaw could be attributed to the one-piece design and surface characteristics of the implant that could have influenced osseointegration. Further clinical trials are recommended to evaluate the performance of zirconia implants under loading conditions.