WorldWideScience

Sample records for plastered silo loss

  1. Dry matter losses of grass, lucerne and maize silages in bunker silos

    Directory of Open Access Journals (Sweden)

    Brigitte Koehler

    2013-03-01

    Full Text Available An efficient feed management is important for a sustainable and economic agricultural production. One of the main points for improving the efficiency is the reduction of feed losses. In the present investigation the dry matter (DM losses of grass, lucerne and maize silages in farm scaled bunker silos were analysed. The method of determining DM losses was the total-in versus total-out DM mass flow of the silos, including the determination of DM content and other silage parameters via manual sampling. The results taken from 48 silos showed on average for all investigated crops 9–12% of DM losses. Density and feed out rate showed a negative correlation to DM losses in maize silages. According to the applied method for determining DM losses on farm scale, a guideline of 8% can be suggested for maximum DM losses in bunker silos for grass and maize silages. The described method seems to be applicable for improving the feed management by using largely automated measurements on the harvest and feeding side.

  2. Effect of harvest time on fermentation profiles of maize ensiled in laboratory silos and determination of drying losses at 60°C

    DEFF Research Database (Denmark)

    Nielsen, Tina Skau; Kristensen, Niels Bastian; Weisbjerg, Martin Riis

    2007-01-01

    The objectives were to investigate the effect of premature ensiling of maize on alcohol fermentation in laboratory silos and the loss of fermentation products and glucose in silage following drying at 60°C for 48 h. During four consecutive weeks maize was harvested and ensiled for 60 days in vacuum......-sealed laboratory silos. The content of DM in silage increased (p...-glucose content was reduced by approximately 45% after drying. Alcohols and esters were completely lost in drying. We conclude that ensiling of pre-mature maize does not lead to extensive alcohol fermentation in laboratory silos following 60 days of ensiling, and that dry matter correction based on fermentation...

  3. Adhesive plasters

    Science.gov (United States)

    Holcombe, Jr., Cressie E.; Swain, Ronald L.; Banker, John G.; Edwards, Charlene C.

    1978-01-01

    Adhesive plaster compositions are provided by treating particles of Y.sub.2 O.sub.3, Eu.sub.2 O.sub.3, Gd.sub.2 O.sub.3 or Nd.sub.2 O.sub.3 with dilute acid solutions. The resulting compositions have been found to spontaneously harden into rigid reticulated masses resembling plaster of Paris. Upon heating, the hardened material is decomposed into the oxide, yet retains the reticulated rigid structure.

  4. EVALUATION OF CEMENT THIXOTROPY FOR THE CEMENT OF OIL WELLS IN AREAS WITH LOSSES: EFFECT OF PLASTER AND DAIRY OF HIGH FURNACES

    Directory of Open Access Journals (Sweden)

    T. Bouziani

    2010-12-01

    Full Text Available Cementing of oil and gas wells can be a very delicate operation. Among the concerns of service companies, during this operation are the nature and conditions of the formations in well. This is the case of cementing operations in southern Algeria, specifically on the fields of In-Amen, where the formations in lost zones are naturally weak and highly permeable. In these areas, drilling fluids (muds and cements pumped will be, completely or partially lost, what we call "lost circulation". Thixotropic cements are useful to overcome lost circulation problems. They are characterized by a special rheological behavior, allowing it to plug lost zones when they are pumped. Our work aims to assess the thixotropy of cements perapred with two types of cement (class G Asland cement and CEM I 42.5 portland cement with the plaster, using a viscometer with coaxial cylinder (couette type. Moreover, the effect of blast furnace slag (LHF on the properties and thixotropic mixtures prepared was also studied. The results show that portland cement (available locally can produce mixes with higher and more stable thixotropy than the class G cement (from importation, which is a practical and economical for cementing job operations in wells with loss zones. The results also show that the effect of LHF is positive, since in addition to his contribution to long term performances, especially the durability of hardened concrete, it improves the thixotropy of cement made of plaster.

  5. Influence of prior activity on residual limb volume and shape measured using plaster casting: Results from individuals with transtibial limb loss

    Directory of Open Access Journals (Sweden)

    Joan E. Sanders, PhD

    2013-10-01

    Full Text Available The purpose of this research was to determine whether prior activity affected the shape of a plaster cast taken of a transtibial residual limb. Plaster casts were taken twice on one day in 24 participants with transtibial limb loss, with 5 s between doffing and casting in one trial (PDI-5s and 20 min in the other trial (PDI-20m. The ordering of the trials was randomized. The mean +/- standard deviation radial difference between PDI-20m and PDI-5s was 0.34 +/- 0.21 mm when PDI-5s was conducted first and -0.02 +/- 0.20 mm when PDI-20m was conducted first. Ordering of the trials had a statistically significant influence on the mean radial difference between the two shapes (p = 0.008. The result shows that prior activity influenced the residual limb cast shape. Practitioners should be mindful of prior activity and doffing history when casting an individual's limb for socket design and prosthetic fitting.

  6. Effect of a dual-purpose inoculant on the quality and nutrient losses from corn silage produced in farm-scale silos.

    Science.gov (United States)

    Queiroz, O C M; Adesogan, A T; Arriola, K G; Queiroz, M F S

    2012-06-01

    This project aimed to determine effects of applying an inoculant containing homofermentative and heterofermentative bacteria on the fermentation, nutritive value, aerobic stability, and nutrient losses from corn silage produced in farm-scale silos. Corn forage was harvested at 34% dry matter (DM) and treated without (control) or with 5 × 10⁵ cfu/g of Lactobacillus buchneri and Pediococcus pentosaceus. The inoculant was sprayed on alternate 8-row-wide swaths of forage, and the untreated and inoculated forages were alternately packed into 3.6-m-wide bag silos. Forty-five tonnes of corn forage were packed into each of 4 replicate bags per treatment and ensiled for 166 d. Silage removed from the bags (500 kg/d) was separated into good and spoiled (visibly moldy or darker) silage portions, and weighed for 35 d. Weekly composites were analyzed for chemical composition, aerobic stability, and fungal counts. Aerobic stability was measured using data loggers that recorded sample and ambient temperature every 30 min for 7 d. Inoculation did not affect the chemical composition of the spoiled or good silage but decreased the quantity (5.7 vs. 12.9 kg/d) and percentage (3.4 vs. 7.8) of spoiled silage in the bags by over 50%. Losses of crude protein (0.28 vs. 0.92 kg/d), gross energy (6.0 × 10⁴ vs. 1.8 × 10⁵ kJ/d), and neutral detergent fiber (1.34 vs. 4.12 kg/d) in spoiled silage were less in inoculated versus control silages. Inoculated silages had lower pH (3.91 vs. 3.99), lactate concentration (7.63 vs. 7.86%), lactate:acetate ratio (1.58 vs. 2.53%), and a greater acetate (5.11 vs. 3.56%) concentration than the control silage. Inoculated silages tended to have fewer yeasts (2.59 vs. 4.62 log cfu/g) than control silages, but aerobic stability was not different across treatments (14.7 vs. 9.5 h). Applying the inoculant made the fermentation more heterolactic, inhibited the growth of yeasts, and substantially reduced the amount of spoilage and the associated energy and

  7. Plaster core washout tool

    Science.gov (United States)

    Heisman, R. M.; Keir, A. R.; Teramura, K.

    1977-01-01

    Tool powered by pressurized water or air removes water soluble plaster lining from Kevlar/epoxy duct. Rotating plastic cutterhead with sealed end fitting connects flexible shaft that allows tool to be used with curved ducts.

  8. Nuevo silo – Austria

    Directory of Open Access Journals (Sweden)

    Schmidt, W.

    1971-11-01

    Full Text Available The firm Waagner-Biro, collaborating with Farbwerke Hoechst, AG., of Frankfurt, and with assistance from the Austrian Government, has designed and produced a new type of silo, made of steel, intended for use in underdeveloped countries, in emergency areas, and in any zone where silos are needed which can be rapidly assembled and taken down, are light in weight and easy to transport. These silos can contain solids, liquids, and, with a special external treatment, also aggressive chemicals for agricultural purposes.La firma Waagner-Biro, en colaboración con la Farbwerke Hoechst AG de Frankfurt y bajo la eficaz promoción del Gobierno austríaco, fabrica este moderno silo de acero-trevira destinado a cubrir las necesidades de países en vía de desarrollo, de zonas catastróficas y, en general, de cualquier lugar donde se requiera gran rapidez de montaje y desmontaje, poco peso propio y facilidad subsiguiente de transporte y celeridad de entrega. Puede contener productos sólidos y líquidos y, aplicándole un recubrimiento especial, incluso materias químicas biológicamente agresivas.

  9. Collaboration across clinical silos.

    Science.gov (United States)

    Mohler, M Jane

    2013-01-01

    We face significant challenges to healthcare integration as well as tremendous opportunities to advance healthcare reform as we endeavor to provide a coordinated continuum of high-value services to defined populations for which we are clinically and fiscally accountable. As we move away from fee-for-service and poorly coordinated care toward value-based and bundled care, systems such as UnityPoint Health and clinical entities such as Piedmont Heart are leading the way, breaking down their clinical silos, improving value and access, and gaining patient loyalty. Evidence points us to sound principles that can inform the clinical integration process. Health systems must reinvent themselves, reengineer clinical operations, and streamline processes, all of which require collaboration across traditional silos, both inside our organizations and outside into our wider communities, to ensure that our patients receive the safe, high-value care they deserve.

  10. Silo Storage Preconceptual Design

    Energy Technology Data Exchange (ETDEWEB)

    Stephanie L. Austad; Patrick W. Bragassa; Kevin M Croft; David S Ferguson; Scott C Gladson; Annette L Shafer; John H Weathersby

    2012-09-01

    The National Nuclear Security Administration (NNSA) has a need to develop and field a low-cost option for the long-term storage of a variety of radiological material. The storage option’s primary requirement is to provide both environmental and physical protection of the materials. Design criteria for this effort require a low initial cost and minimum maintenance over a 50-year design life. In 1999, Argonne National Laboratory-West was tasked with developing a dry silo storage option for the BN-350 Spent Fuel in Aktau Kazakhstan. Argon’s design consisted of a carbon steel cylinder approximately 16 ft long, 18 in. outside diameter and 0.375 in. wall thickness. The carbon steel silo was protected from corrosion by a duplex coating system consisting of zinc and epoxy. Although the study indicated that the duplex coating design would provide a design life well in excess of the required 50 years, the review board was concerned because of the novelty of the design and the lack of historical use. In 2012, NNSA tasked Idaho National Laboratory (INL) with reinvestigating the silo storage concept and development of alternative corrosion protection strategies. The 2012 study, “Silo Storage Concepts, Cathodic Protection Options Study” (INL/EST-12-26627), concludes that the option which best fits the design criterion is a passive cathotic protection scheme, consisting of a carbon steel tube coated with zinc or a zinc-aluminum alloy encapsulated in either concrete or a cement grout. The hot dipped zinc coating option was considered most efficient, but the flame-sprayed option could be used if a thicker zinc coating was determined to be necessary.

  11. Plaster-Wrap Dragons

    Science.gov (United States)

    Vance, Shelly

    2012-01-01

    In this article, the author describes how her students constructed a three-dimensional sculpture of a dragon using plaster wrap and other materials. The dragons were formed from modest means--using only a toilet-paper tube, newsprint, tape and wire.

  12. Plaster-Wrap Dragons

    Science.gov (United States)

    Vance, Shelly

    2012-01-01

    In this article, the author describes how her students constructed a three-dimensional sculpture of a dragon using plaster wrap and other materials. The dragons were formed from modest means--using only a toilet-paper tube, newsprint, tape and wire.

  13. Plaster, Portraits and Pots.

    Science.gov (United States)

    Schimsky, Marc

    1982-01-01

    Describes an art activity in which junior high school students make portrait pots using plaster casts and clay. Each student created a reflection of his or her personality in clay. Specific teaching methods and ways of working with materials are discussed. (AM)

  14. Siloette, Siloe mock-up; Siloette, modele nucleaire de siloe

    Energy Technology Data Exchange (ETDEWEB)

    Delcroix, V.; Jeanne, G.; Mitault, G.; Schulhof, P. [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

    1964-07-01

    Siloette is the Siloe mock-up. The main installations are described: various tanks, building, auxiliaries, control systems... Precis ions are given about precautions taken for using spent fuel elements. (authors) [French] Siloette est le modele nucleaire de SILOE. On decrit ses diverses installations: bassins, batiments, auxiliaires, controle... Des precisions sont donnees sur les precautions prises pour y utiliser des elements uses. (auteurs)

  15. [PHYSICAL PROPERTIES OF PLASTER BANDAGES].

    Science.gov (United States)

    Antabak, Anko; Barisić, Branimir; Andabak, Matej; Bradić, Lucija; Brajcinović, Melita; Haramina, Tatjana; Haluzan, Damir; Fuchs, Nino; Durkovir, Selena; Curković, Selena; Luetić, Tomislav; Sisko, Jerko; Prlić, Ivica

    2015-01-01

    The physical properties of plaster bandages are a very important factor in achieving the basic functions of immobilization (maintaining bone fragments in the best possible position), which directly affects the speed and quality of fracture healing. This paper compares the differences between the physical properties of plaster bandages (mass, specific weight, drying rate, elasticity and strength) and records the differences in plaster modeling of fast bonding 10 cm wide plaster bandages, from three different manufacturers: Safix plus (Hartmann, Germany), Cellona (Lohman Rauscher, Austria) and Gipsan (Ivo Lola Ribar ltd., Croatia). Plaster tiles from ten layers of plaster, dimension 10 x 10 cm were made. The total number of tiles from each manufacturer was 48. The water temperature of 22 °C was used for the first 24 tiles and 34 'C was used for the remainder. The average specific weight of the original packaging was: Cellona (0.52 g/cm3), Gipsan (0.50 g/cm3), Safix plus (0.38 g/cm3). Three days after plaster tile modeling an average specific weight of the tiles was: Gipsan (1.15 g/cm3), Safix plus (1.00 g/cm3), Cellona (1.10 g/cm3). The average humidity of 50% for Safix plus and Cellona plaster tiles was recorded 18 hours after modeling, while for the Gipsan plaster tiles, this humidity value was seen after 48 hours. On the third day after plaster modeling the average humidity of the plaster tiles was 30% for Gipsan, 24% for Safix and 16% for Cellona. Cellona plaster tiles made with 34 °C water achieved the highest elasticity (11.75±3.18 MPa), and Gipsan plaster tiles made with 22 °C had the lowest (7.21±0.9 MPa). Cellona plaster tiles made with 34 °C water showed maximum material strength (4390±838 MPa), and Gipsan plaster tiles made with 22 °C water showed the lowest material strength (771±367 MPa). The rigidity and strength of Cellona and Gipsan plaster are higher in tiles made in warmer water, and for Safix plus are higher in tiles made in cooler water

  16. Silo model tests with sand

    DEFF Research Database (Denmark)

    Munch-Andersen, Jørgen

    Tests have been carried out in a large silo model with Leighton Buzzard Sand. Normal pressures and shear stresses have been measured during tests carried out with inlet and outlet geometry. The filling method is a very important parameter for the strength of the mass and thereby the pressures...... as well as the flow pattern during discharge of the silo. During discharge a mixed flow pattern has been identified...

  17. Moisture transport in coated plaster

    NARCIS (Netherlands)

    Goossens, E.L.J.; Van der Spoel, W.H.; Bancken, E.L.J.

    2001-01-01

    In the framework of the research project: 'Water balance of water-borne paint systems on plaster substrates in relation to fungal growth', a study is carried out to moisture transport mechanisms in coated gypsum plaster. In this contribution, the set-up of the study is described. Besides a descripti

  18. Moisture transport in coated plaster

    NARCIS (Netherlands)

    Goossens, E.L.J.; Van der Spoel, W.H.; Bancken, E.L.J.

    2001-01-01

    In the framework of the research project: 'Water balance of water-borne paint systems on plaster substrates in relation to fungal growth', a study is carried out to moisture transport mechanisms in coated gypsum plaster. In this contribution, the set-up of the study is described. Besides a descripti

  19. Silo model tests with sand

    DEFF Research Database (Denmark)

    Munch-Andersen, Jørgen

    Tests have been carried out in a large silo model with Leighton Buzzard Sand. Normal pressures and shear stresses have been measured during tests carried out with inlet and outlet geometry. The filling method is a very important parameter for the strength of the mass and thereby the pressures...

  20. Parametric study of silo-material interaction

    Science.gov (United States)

    Hasanain, G. S.

    1981-06-01

    The methods for determination of pressures and the analysis of silos for storage of granular materials are reviewed. A finite element procedure for linear analysis and an initial-strain analysis of hoop forces and horizontal bending moments in circular concrete silos with bisymmetric outlets is presented, and these methods are compared with the hoop steel areas obtained using current practice. A concrete coal silo is designed by these methods and compared with one designed by standard methods.

  1. Statistical analysis of silo wall pressures

    DEFF Research Database (Denmark)

    Ditlevsen, Ove Dalager; Berntsen, Kasper Nikolaj

    1998-01-01

    Previously published silo wall pressure measurements during plug flow of barley in alarge concrete silo are re-analysed under the hypothesis that the wall pressures are gamma-distributed.The fits of the gamma distribution type to the local pressure data from each measuring cell are satisfactory.......However, the estimated parameters of the gamma distributions turn out to be significantly inhomogeneous overthe silo wall surface. This inhomogeneity is attributed to the geometrical imperfections of the silo wall.Motivated by the engineering importance of the problem a mathematical model for constructing astochastic...

  2. Grindability, Grading and Wettability of Recycled Plaster

    Institute of Scientific and Technical Information of China (English)

    李志新; 彭家惠; 赵海鑫; 邱星星; 赵敏

    2016-01-01

    The changes of grindability, grading and wettability of recycled plaster(R-P)and the mechanisms of these changes were studied by using vickers hardness, particle size distribution(PSD), scanning electron micro-scope(SEM) and nitrogen adsorption porosimetry to reveal that R-P was obviously different from plaster of Paris(POP). At the same milling time, R-P had the characteristics of high specific surface area, fine particle diame-ter and uneven size distribution compared with POP, so R-P possessed both good grindability and poor grading. The water absorption, dissolution rate and mass loss in dry-wet cycle of the hardened recycled gypsum(hardened RG) increased, while the water saturated strength and dry-wet cycle strength decreased significantly compared with the hardened virgin gypsum(hardened VG). Therefore, poor wettability could be seen in R-P. The analyses indi-cated that the changes of grindability and grading could be attributed to the reduction in hardness and the increase in the porosity of hardened RG and that the poor wettability of R-P was caused by the increase of large pores and the changes of microstructure of hardened RG.

  3. Armazenamento de soja em silos tipo bolsa Soybean storage in bag type silos

    Directory of Open Access Journals (Sweden)

    Lêda R. A. Faroni

    2009-03-01

    moisture contents similar to the original levels during the storage period. There was a tendency for to increase in the electric conductivity and decrease in the germination percentage of moist soybeans, especially after a ninety-day storage. The apparent grain density of moist or dry soybeans did not decrease. As regarding to the qualitative parameters of crude oil, the values remained below the legal limits required for marketing crude soybean oil. From the results it can be concluded that bag type silos represent a viable alternative for soybean storage without quality loss, and also storage in such structures does not lead to qualitative changes in the crude oil obtained from such grains.

  4. The valuation of commercial grain silos

    African Journals Online (AJOL)

    The profits method of valuation should also be considered and is used to value properties with ... comparable sales of grain silos on the open market, the capitalisation ..... If these silos trade, it may be difficult to obtain the detail occupancies ...

  5. Methods of lab silos sealing and fermentation characteristics and aerobic stability of sugarcane silage treated with microbial additive

    Directory of Open Access Journals (Sweden)

    Charles Ortiz Novinski

    2012-02-01

    Full Text Available The present experimental assay evaluated the effect of lab silo sealing methods on the ensilage of the sugarcane, with or without microbial additives (Lactobacillus plantarum and Propionibacterium acidipropionici. Twenty-liter plastic buckets were used as experimental silos, which were sealed with either a polyethylene sheet (silo cover with a mesh size of 200 µm or an appropriate plastic lid equipped with Bunsen valve. Silos were stored for 30, 60, or 90 days. Fermentative losses, chemical composition, organic acids, ethanol and aerobic stability were evaluated. The sealing method employed did not influence most of evaluated variables, showing a small decrease of effluent production in silos covered with polyethylene sheet. The microbial additive did not avoid dry matter (DM fermentative losses in sugarcane silages (216 g kg-1, nor affected aerobic stability (44.6 hours. The levels of neutral and acid detergent fiber of fresh sugarcane increased after ensiling due to DM losses as gases and effluent. The ethanol content of silages was not influenced by treatments (mean 146 g kg-1 of DM. The sealing methods of experimental silos were not affected by the evaluated variables; polyethylene sheet and plastic lid show the same performance on the fermentative model and both methods represent well the conditions of large scale farm silos.

  6. Fire and fire extinguishment in silos. An experimental study[Storage of wood fuel pellets]; Brand och brandslaeckning i siloanlaeggningar. En experimentell studie

    Energy Technology Data Exchange (ETDEWEB)

    Persson, Henry; Blomqvist, Per; Zhenghua Yan

    2007-01-15

    tight silo, as any holes or leaks will feed the pyrolysis with oxygen, and could further result in losses of the extinguishing gas. A silo should thus be designed with the means to close the silo air tight during extinguishment of a fire. The efficiency of the extinction could be further enhanced by application of low or medium expansion fire fighting foam on top of the stored material in the silo. It could further be appropriate to inject inert gas in the void top space of the silo in an early stage of the fire fighting in order to reduce the risk for gas/dust explosion. Generally, emptying of the silo should not be initiated before the fire is appropriately suppressed, i.e. not before the pyrolysis activity (temperature) has been considerably reduced. An inert atmosphere should further be maintained in the silo during the entire period while emptying the silo. Water should not be used as an extinguishing media, as water could result in considerably expansion (swelling) of the porous material in the silo. This could both damage the silo construction and make the stored material to stick on the silo walls.

  7. Plaster of Paris: the orthopaedic surgeon heritage.

    Science.gov (United States)

    Hernigou, Philippe

    2016-08-01

    Plastering is one of the most ancient of the building handicrafts. Plaster is the common name for calcium sulphate hemi hydrate made by heating the mineral gypsum, the common name for sulphate of lime. In the tenth century the Arabs used liquid plaster in orthopaedic treatment. At the beginning of the nineteenth century, patients with fractures of the lower extremities-and often of the upper extremities as well-were treated in bed with restriction of all activity for many weeks until the fractures united. It was the practice of surgeons to dress wounds and fractures at frequent intervals. The bandages, pads, and splints were removed, the fractures manipulated, and the dressings reapplied. The search for simpler, less cumbersome methods of treatment led to the development of occlusive dressings, stiffened at first with starch and later with plaster of Paris. The ambulatory treatment of fractures was the direct result of these innovations. Two military surgeons, Antonius Mathijsen of the Netherlands, and Nikolai Ivanovitch Pirogov of Russia, were responsible for the introduction of the new plaster bandage technique. At the beginning of the twentieth century the technique was improved by Jean-François Calot, a French surgeon, who invented the hand manufacture of plaster bandage as a roll. During the twentieth century, walking cast and ambulation for fresh fractures were developed with plaster and pin incorporated in plaster; the open fracture care concept was introduced with plaster of Paris by Trueta before the external fixation.

  8. Modeling ventilation time in forage tower silos.

    Science.gov (United States)

    Bahloul, A; Chavez, M; Reggio, M; Roberge, B; Goyer, N

    2012-10-01

    The fermentation process in forage tower silos produces a significant amount of gases, which can easily reach dangerous concentrations and constitute a hazard for silo operators. To maintain a non-toxic environment, silo ventilation is applied. Literature reviews show that the fermentation gases reach high concentrations in the headspace of a silo and flow down the silo from the chute door to the feed room. In this article, a detailed parametric analysis of forced ventilation scenarios built via numerical simulation was performed. The methodology is based on the solution of the Navier-Stokes equations, coupled with transport equations for the gas concentrations. Validation was achieved by comparing the numerical results with experimental data obtained from a scale model silo using the tracer gas testing method for O2 and CO2 concentrations. Good agreement was found between the experimental and numerical results. The set of numerical simulations made it possible to establish a simple analytical model to predict the minimum time required to ventilate a silo to make it safe to enter. This ventilation time takes into account the headspace above the forage, the airflow rate, and the initial concentrations of O2 and CO2. The final analytical model was validated with available results from the literature.

  9. Characterization of Fernald Silo 3 Waste

    Energy Technology Data Exchange (ETDEWEB)

    Langton, C.A.

    2001-04-04

    This report summarizes characterization results for uranium residues from the Fernald Environmental Management Project (FEMP) Operable Unit (OU-4). These residues are currently stored in a one-million-gallon concrete silo, Silo 3, at the DOE Fernald Site, Ohio. Characterization of the Silo 3 waste is the first part of a three part study requested by Rocky Mountain Remedial Services (RMRS) through a Work for others Agreement, WFO-00-007, between the Westinghouse Savannah River Company (WSRC) and RMRS. Parts 2 and 3 of this effort include bench- and pilot-scale testing.

  10. Performance evaluation of termite-mound clay, concrete and steel silos for the storage of maize grains in the humid tropics

    Science.gov (United States)

    Inadequate storage facilities have contributed to severe maize postharvest losses in many developing countries. This study determined the potential of termite mound clay (TMC), a readily-available material in Nigeria, as a construction material for storage silos. The performance of the TMC silo was ...

  11. The four silo STK Powderhorn Tape Library

    CERN Multimedia

    Patrice Loïez

    2001-01-01

    A view of the four silo Storage Tek (STK) Powderhorn Tape Library and its control area. Each silo can contain up to 6000 storage slots with cartridges of 10, 20, 25 or 50 GB capacity, reaching a data transfer rate of up to 12 Mbytes/sec. This will form part of the Grid system that will process the huge amounts of data produced at the LHC.

  12. Silo Collapse under Granular Discharge

    Science.gov (United States)

    Gutiérrez, G.; Colonnello, C.; Boltenhagen, P.; Darias, J. R.; Peralta-Fabi, R.; Brau, F.; Clément, E.

    2015-01-01

    We investigate, at a laboratory scale, the collapse of cylindrical shells of radius R and thickness t induced by a granular discharge. We measure the critical filling height for which the structure fails upon discharge. We observe that the silos sustain filling heights significantly above an estimation obtained by coupling standard shell-buckling and granular stress distribution theories. Two effects contribute to stabilize the structure: (i) below the critical filling height, a dynamical stabilization due to granular wall friction prevents the localized shell-buckling modes to grow irreversibly; (ii) above the critical filling height, collapse occurs before the downward sliding motion of the whole granular column sets in, such that only a partial friction mobilization is at play. However, we notice also that the critical filling height is reduced as the grain size d increases. The importance of grain size contribution is controlled by the ratio d /√{R t }. We rationalize these antagonist effects with a novel fluid-structure theory both accounting for the actual status of granular friction at the wall and the inherent shell imperfections mediated by the grains. This theory yields new scaling predictions which are compared with the experimental results.

  13. Plaster: our orthopaedic heritage: AAOS exhibit selection.

    Science.gov (United States)

    DeMaio, Marlene; McHale, Kathleen; Lenhart, Martha; Garland, Joshua; McIlvaine, Christopher; Rhode, Michael

    2012-10-17

    Plaster has been used for centuries as a stiffening agent to treat fractures and other musculoskeletal conditions that require rest, immobilization, or correction of a deformity. Despite modern metallurgy and internal stabilization, plaster casts and splints remain an important means of external stabilization. Casting is a dying art as modern internal and external fixation replace external immobilization. Proper casting technique is paramount. This manuscript outlines the history and chemistry of immobilization materials and techniques as well as the differences among them and the advantages and disadvantages of each. Historical references, peer-reviewed journals, textbooks, and primary sources were reviewed to provide data for this review. The history of immobilization reveals a progressive development and refinement of materials that culminated in Mathijsen's plaster bandage in 1851. In 1798, calcium sulfate (plaster of Paris) was introduced. By 1927, crinoline rolls dipped in plaster treated with binding agents facilitated application. Synthetic casting "tapes" (45% polyurethane resin and 55% fiberglass) were introduced in the 1970s. Splinting techniques are ancient, with development spurred by treatment of war wounds. Plaster relies on soft-tissue contact to maintain rigidity. There are well-known advantages, disadvantages, and complications of plaster management. Casting materials all create an exothermic reaction. Burns are associated with water temperatures of >24°C, more than eight layers (ply), and inadequate ventilation. The maximum water temperature must be lower with fiberglass casts. Plaster was the definitive management for most fractures for over 100 years until it was replaced by modern surgical techniques involving internal fixation in the latter part of the twentieth century. Plaster casts and splints remain an important treatment method for acute and chronic orthopaedic conditions.

  14. Prediction of silo-vibrations using a modified lambdameter

    Science.gov (United States)

    Jäckel, Stefan; Schünemann, Ralf; Mütze, Thomas; Peuker, Urs A.

    2013-06-01

    Predicting silo-vibrations is not yet universally possible but only to a very limited extent. A mechanism of excitation of silo vibrations can be found in oscillating shear stresses between the bulk solid and the inner silo wall, the so-called "wall-stick-slip" effect. So if this wall-stick-slip occurs during shear experiments in shear testers, the probability of silo-vibrations in silos will be high. However if there is no slip-stick effect observed, this will not consequently exclude silo-vibrations. The influences on a stable stick-slip were studied in wall friction experiments with a rotational shear tester and in a specially developed silo model based on a lambdameter. The examined parameters are normal stress, shear velocity, wall roughness and particle shape. Plastic pellets which are known to honk (PET, PA) and plastic pellets that do not honk (PE) are considered [1]. It is shown that the silo model based on a lambdameter is more suitable for initiation and measurement of stable wall-stick-slip of granular media than the conventional rotational shear tester. The industrial experiences in respect of silo vibrations are proved in the silo model for all tested types of plastic pellets. So, if the origin of silo vibrations is wall-stick-slip, the silo model based on a lambdameter gives a better opportunity for predicting silo vibrations. This paper gives a summary on the results obtained with the new method.

  15. Los empujes del material almacenado en silos

    Directory of Open Access Journals (Sweden)

    Ayuga, Francisco

    1995-04-01

    Full Text Available The design of silos has been the object of scientific and technical research for a whole century and this has led to great advances in the field. The results have not always been adequately disseminated among the technicians. The aim of this paper is to present the techniques for calculation of the loads of the materials stored in silos, inform about and comment on the standards, introduce the latest works carried out worldwide based on the finite elements method and, lastly, venture an opinion on the changes this may cause in the future.

    Durante un siglo el cálculo de silos ha sido objeto de investigación científica, técnica y aplicada y se han producido grandes avances. Todo este desarrollo no siempre ha sido bien dado a conocer entre los técnicos. El objeto de este artículo es precisamente presentar las técnicas de cálculo de acciones del material almacenado en silos, presentar y comentar la normativa, introducir los últimos trabajos que en el cálculo de silos se están haciendo en todo el mundo basados en la técnica de los elementos finitos y aventurar los cambios que esto va a suponer en un futuro.

  16. Silo with a Corrugated Sheet Wall

    Science.gov (United States)

    Németh, Csaba; Brodniansky, Ján

    2013-09-01

    Silos and tanks are currently being used to create reserves of stored materials. Their importance is based on balancing the production and consumption of bulk materials to establish an adequate reserve throughout the year. The case study introduced within the framework of this paper focuses on thin-walled silos made of corrugated sheets and on an approach for designing these types of structures. The storage of bulk materials causes compression or tensile stresses in the walls of a silo structure. The effect of a frictional force in the silo walls creates an additional bending moment in a wave, which ultimately affects the resulting bending moments. Several mathematical and physical models were used in order to examine various types of loading and their effects on a structure. Subsequently, the accuracy of the computational models was verified by experimental measurements on a grain silo in Bojničky, Slovakia. A comparison of the experimental and mathematical models shows a reasonable match and confirms the load specifications, while indicating that the mathematical model was correct.

  17. Ballistic Missile Silo Door Monitoring Analysis

    Energy Technology Data Exchange (ETDEWEB)

    EDENBURN,MICHAEL W.; TROST,LAWRENCE C.

    2000-01-01

    This paper compares the cost and effectiveness of several potential options that may be used to monitor silo-based ballistic missiles. Silo door monitoring can be used to verify that warheads removed to deactivate or download silo-based ballistic missiles have not been replaced. A precedent for monitoring warhead replacement using reentry vehicle on site inspections (RV-OSIs) and using satellites has been established by START-I and START-II. However, other monitoring options have the potential to be less expensive and more effective. Three options are the most promising if high verification confidence is desired: random monitoring using door sensors; random monitoring using manned or unmanned aircraft; and continuous remote monitoring using unattended door sensors.

  18. [Application of modified plaster material and device in acupoint plaster therapy].

    Science.gov (United States)

    Liu, Jing-Xing; Wang, Kui; Wang, De-Li; Yang, Zong-Yun

    2013-02-01

    Through the analysis on the methods of medicinal paste preparation, the irritation of skin to medicine and the plaster materials adopted in acupoint plaster therapy for the prevention of winter-attacked disease in summer, the acupoint plaster materials and devices were improved. According to the differences in age, illness condition, acupoint and medicinal irritation of patients, the high-dosage, moderate-dosage and low-dosage series of medicine were prepared in proportion; 2. 5 mL and 5 mL syringes were manually reconstructed as the pushers for the delivery of the medicine paste of different specifications. The new-type materials such as spun-bonded non-woven fabrics, transparent dressing film and spun-laced non-woven skin-color stick plaster were adopted. In the operation, the medicine was classified and prepared more specifically. The dedicated acupoint plaster was characterized as less in skin irritation, breathable in property, convenient in practice and proper in stickiness. The plastic anti-seepage film in the middle and the medicine storage pool for stabilizing medicinal paste could avoid drug leakage. The medicinal paste pusher could achieve the even size, proper thickness and precise dosage of the paste. The new-type plaster material and the self-prepared innovated plaster device contribute to the development of acupoint plaster therapy in clinical application.

  19. Application of electrostatic prevention technology on polyethylene silos

    Science.gov (United States)

    Gong, Hong; Liu, Quanzhen; Tan, Fenggui; Zhang, Yunpeng

    2013-03-01

    The main reasons of static electric explosion accidents in polyolefin plant silos were analyzed in this paper, and the study finds that the reasons include control failure of flammable gas content in the feed, high electrification caused by the wind supply, and frequent electrostatic discharge in silos. The electrostatic-reducing technologies of polyolefin powder were introduced, and its application performance in polyolefin plant silos was also clarified. In addition, the methods including FDCS and DGES for evaluation of electrostatic explosion in polyolefin plant silo were proposed. In the end, the risk of electrostatic explosion in PE plant blended silo was evaluated before and after application of electrostatic reducing technology.

  20. Breaking down silos and building teamwork.

    Science.gov (United States)

    Lunn, T

    1997-11-01

    The purpose of this article is to explain how successful companies break down old functional silos and build teamwork. It describes techniques that foster teamwork across functional departments within a company as well as methods that can be used to cut across company lines and break down barriers between organizations.

  1. Undercoat Roughness Impact on Venetian Plasters Adhesive Strength

    Directory of Open Access Journals (Sweden)

    Vladimir V. Vakor

    2011-11-01

    Full Text Available The article studies impact of undercoat fractions size on Venetian plasters adhesive strength, describes acrylic and lime plasters adhesive features, offers method for adherence junctions strength evaluation.

  2. Atomic Oxygen Cleaning of Unpainted Plaster Sculptures

    Science.gov (United States)

    Banks, Bruce A.; Miller, Sharon K.

    2017-01-01

    Atomic oxygen erosion of polymers has been found to be a threat to spacecraft in low Earth orbit. As a result ground facilities have been developed to identify coatings to protect polymers such as used for solar array blankets. As a result of extensive laboratory testing, it was discovered that soot and other organic contamination on paintings could be readily removed by atomic oxygen interactions with minimal damage to the artwork. No method, other than dusting, has been found to be effective in the cleaning of unpainted plaster sculptures This presentation discusses the atomic oxygen interaction processes and how effective they are for cleaning soot damaged unpainted plaster sculptures.

  3. SIMULATION OF A MATHEMATICAL MODEL FOR THE TEMPERATURE PROFILE IN A SILO BAG FOR BEAN

    Directory of Open Access Journals (Sweden)

    M. R. Hauth

    2015-02-01

    Full Text Available The problems encountered with storage of agricultural products has warranted studies related to finding alternative methods of grain storage, thereby avoiding unnecessary losses. Stored grain deteriorates quickly at high temperatures. The moisture content of the grain influences the respiratory process; therefore, when at the recommended humidity of between 11 and 13%, this rate remains low, it prolongs maintenance of the product quality. The silo bag being airtight enables the grain mass to consume the entire internal O2 purse within it, and in that low or absent oxygen environment the grain mass saturates the CO2 atmosphere, inhibiting the multiplication of insects and fungi, thus providing a controlled environment. This study aims at simulating, using Computational Fluid Dynamics (CFD, the time it would take for the entire grain mass contained in a silo bag to reach thermal equilibrium with the environment and analyzes the feasibility of the technique employed here. The simulations were performed based on the data of the average air temperature in the region at each harvest time and the average storage temperature of the bean mass (60°C. The results obtained from the simulations reveal that after one month of silo storage the entire bag remains in thermal stabilization, and four months later when it hits the entire mass, all the beans are in thermal equilibrium. Therefore, maintaining stable temperature and humidity within the recommended silo bag preserves the grain quality well.

  4. Silo effect a prominence factor to decrease efficiency of pharmaceutical industry.

    Science.gov (United States)

    Vatanpour, Hossein; Khorramnia, Atoosa; Forutan, Naghmeh

    2013-01-01

    To be sure, all the industries try to be involved in globalization with a constant trend to find out ways to increase productivity across different functions within an organization to maintain competitive advantage world. Pharmaceutical industries are not exceptional and further are based on fragmentation. So these kind of companies need to cope with several barriers such as silo mentality that may affect efficiency of their business activity. Due to eliminate a part of resources such as raw materials, new molecule developed, financial and human resources and so on, companies can gradually loss their competitive potentials in the market and increase their expenses. Furthermore, to avoid any business disturbances in financially connected companies due to silo effect, they should arrange their management to integrated organization form. Otherwise, actions taken by one business member of the chain can influence the profitability of all the other members in the chain. That is why recently supply chain has generated much interest in many business units. In this paper, it has been tried to investigate the different aspects of silo effect which can affect integrate supply chain. Finally, a fluent communication, high level of information exchange, fragmentation management, cross-functional control in a supply chain management format are needed to reduce or control silo effect within entire chain of the holding company by Supply chain management.

  5. Forced Vibrations of Silos Leading to Buckling

    Science.gov (United States)

    FLORES, FERNANDO G.; GODOY, LUIS A.

    1999-07-01

    The large-amplitude force vibrations of steel thin-walled silos when empty are investigated. The basic geometry configuration modelled is a cylinder clamped at the bottom with a top conical roof. Wind pressure distributions are assumed as non-axisymmetric in the circumferential direction and with a rectangular impulse or step distribution in time. Instability is identified from finite-element computations of the time response of the shell using a criterion due to Budianski and Roth. Results are computed for silos made with plain as well as with corrugated sheets, and the influences of geometric imperfections and the stiffening due to the roof are included in the analysis. The problems are also modelled with static pressures using both continuation techniques and bifurcation analysis from a linear fundamental path. Additional results have been obtained to estimate the dynamic buckling load for step loading using energy procedures. All results are computed using finite-element codes developed by the authors.

  6. Asbestos in Plaster and Wall Systems

    Science.gov (United States)

    This collection of letters and clarification on final rules provides guidance on Asbestos National Emissions Standard for Hazardous Air Pollutants for asbestos-containing join compounds, and asbestos-containing materials found in plaster and wall systems.

  7. Plaster People...A La George Segal.

    Science.gov (United States)

    Boulay, Michele

    2003-01-01

    Describes an art project used with eleventh- and twelfth-grade students in which they created plaster self-portraits inspired by the work of George Segal. Includes directions for the casting and lists the art materials needed for the lesson. Explains that the project requires half a semester to complete. (CMK)

  8. Palatal Surface Area of Maxillary Plaster Casts

    DEFF Research Database (Denmark)

    Darvann, Tron Andre; Hermann, Nuno V.; Ersbøll, Bjarne Kjær

    2007-01-01

    Objective: To investigate the relationship between corresponding two-dimensional and three-dimensional measurements on maxillary plaster casts taken from photographs and three-dimensional surface scans, respectively. Materials and Methods: Corresponding two-dimensional and three-dimensional measu......Objective: To investigate the relationship between corresponding two-dimensional and three-dimensional measurements on maxillary plaster casts taken from photographs and three-dimensional surface scans, respectively. Materials and Methods: Corresponding two-dimensional and three......-dimensional measurements of selected linear distances, curve lengths, and (surface) areas were carried out on maxillary plaster casts from individuals with unilateral or bilateral cleft lip and palate. The relationship between two-dimensional and three-dimensional measurements was investigated using linear regression....... Results and Conclusions: Error sources in the measurement of three-dimensional palatal segment surface area from a two-dimensional photograph were identified as photographic distortion (2.7%), interobserver error (3.3%), variability in the orientation of the plaster cast (3.2%), and natural shape...

  9. Inexpensive, removable coating for plaster tooling

    Science.gov (United States)

    Dimino, J. M.; Martin, R. R.

    1970-01-01

    Procedure for thinning and spaying a vinyl material provides strippable film for plaster surfaces. Coating is low-cost, effective seal against moisture and other sources of damage. Coating consists of a mixture of hot-spray vinyl material and 30 to 50 percent by volume of methyl ethyl ketone.

  10. Exploring the Impact of Silos in Achieving Brand Orientation

    DEFF Research Database (Denmark)

    Gyrd-Jones, Richard; Helm, Clive; Munk, Jonas

    silos are associated with different mindsets that create barriers to the achievement of brand orientation. The case follows a medium sized manufacturing company in its efforts to introduce a brand revitalization strategy across the organization. Despite the strategy having top management full support......, the strategy was not successful due to conflicts in priorities across the functional silos of the organisation. The paper contributes to the literature by highlighting the barriers to the achievement of brand orientation through a focus on silos and mindsets. The paper concludes that the brand platform must...... be implemented meaningfully within each silo....

  11. Large-scale Homogenization of Bulk Materials in Mammoth Silos

    NARCIS (Netherlands)

    Schott, D.L.

    2004-01-01

    This doctoral thesis concerns the large-scale homogenization of bulk materials in mammoth silos. The objective of this research was to determine the best stacking and reclaiming method for homogenization in mammoth silos. For this purpose a simulation program was developed to estimate the homogeniza

  12. Efficacy of heat treatment for disinfestation of concrete grain silos

    Science.gov (United States)

    Field experiments were conducted in 2007 and 2008 to evaluate heat treatment for disinfestations of empty concrete elevator silos. A Mobile Heat Treatment Unit was used to introduce heat into silos to attain target conditions of 50°C for at least 6 h. Ventilated plastic containers with a capacity of...

  13. Plaster body wrap: effects on abdominal fat.

    Science.gov (United States)

    Santos Moreira, Juliana; Melo, Ana Sofia Carneiro Pinto de; Noites, Andreia; Couto, Miriam Faria; Melo, Cristina Argel de; Adubeiro, Nuno Carvalho Freire de Almeida

    2013-12-01

    Abdominal fat is associated with metabolic disorders, leading to cardiovascular risk factors and numerous diseases. This study aimed to analyze the effect of plaster body wrap in combination with aerobic exercise on abdominal fat. Nineteen female volunteers were randomly divided into intervention group (IG; n = 10) performing aerobic exercise with plaster body wrap, and control group (CG; n = 9) performing only exercise. Subcutaneous and visceral fat were measured using ultrasound; subcutaneous fat was also estimated on analysis of skinfolds and abdominal perimeters. At the end of the 10-sessions protocol, the IG demonstrated a significant decrease (p ≤ 0.05) in subcutaneous fat at the left anterior superior iliac spine (ASIS) level and in iliac crest perimeter measurements. A large intervention effect size strength (0.80) was found in subcutaneous fat below the navel and a moderate effect size strength on the vertical abdominal skinfold (0.62) and the perimeter of the most prominent abdominal point (0.57). Comparing the initial and final data of each group, the IG showed a significant decrease in numerous variables including visceral and subcutaneous fat above and below the navel measured by ultrasound (p ≤ 0.05). Plaster body wrap in combination with aerobic exercise seems to be effective for abdominal fat reduction.

  14. The plaster plate becomes a air-conditioner; La plaque de platre se fait climatiseur

    Energy Technology Data Exchange (ETDEWEB)

    Lucat, Th.

    2005-09-01

    BASF company, in association with Knauf, has developed a plaster plate capable to regulate the indoor temperature of a room during summer time. A paraffin-based (wax) phase change material, named Micronal, is included in the plater to store energy during the day and to release it during the night. The lifetime of the phase change material is at least 30 years without loss of efficiency. Short paper. (J.S.)

  15. Flexible intramedullary nails with traction versus plaster cast for treating femoral shaft fractures in children: comparative retrospective study.

    Science.gov (United States)

    Nascimento, Fabiano Prata do; Santili, Cláudio; Akkari, Miguel; Waisberg, Gilberto; Braga, Susana dos Reis; Fucs, Patrícia Maria Moraes de Barros

    2013-01-01

    CONTEXT AND OBJECTIVE Femoral fractures are common in children between 2 and 12 years of age, and 75% of the lesions affect the femoral shaft. Traction followed by a plaster cast is universally accepted as conservative treatment. However, in some situations, a surgical approach is recommended. The objective here was to compare treatments for femoral shaft fractures using intramedullary nails (titanium elastic nails, TEN) versus traction and plaster casts in children. The hypothesis was that TEN might provide better treatment, with good clinical results in comparison with plaster casts. DESIGN AND SETTING This retrospective comparative study was conducted in a public university hospital. METHODS Sixty children with femoral fractures were evaluated; 30 of them underwent surgical treatment with TEN and 30 were treated conservatively using plaster casts. The patients' ages ranged from 5 to 13 years (mean of 9 years). RESULTS The mean duration of hospitalization was nine days for the surgical group and 20 days for the conservative group. The incidence of overgrowth in the patients treated with TEN was 60.0% and, for those treated conservatively, 13.3%. Partial weight-bearing was allowed after 3.5 weeks in the surgical group and after 9.6 weeks in the conservative group. New hospitalization was required for 90.0% in the surgical group and 16.7% in the conservative group. Patients treated with plaster casts presented higher incidence of complications, such as loss of reduction. CONCLUSIONS The surgical method presented better results for children.

  16. Exploring the Impact of Silos in Achieving Brand Orientation

    DEFF Research Database (Denmark)

    Gyrd-Jones, Richard I.; Helm, Clive; Munk, Jonas

    2013-01-01

    Brands are widely recognised as important sources of organisational value. Brand orientation describes the extent to which the organisation is orientated around the brand and around maximising brand potential. However, silos or divisions within the culture of an organisation can frustrate...... the achievement of brand orientation. Through inductive analysis of a case study of an organisation implementing a major brand-revitalisation strategy, this paper demonstrates how, despite a strong brand vision and high level of management commitment, functional silos associated with different mindsets...... contributed to the failure of the new brand strategy. The paper concludes with recommendations for the brand platform to be implemented meaningfully and effectively within each silo....

  17. Design criteria for structural design of silage silo walls

    OpenAIRE

    von Wachenfelt, Hans; Nilsson, Christer; Östergaard, Göran; Olofsson, Anders; Karlsson, Marie

    2014-01-01

    Existing Swedish design guidelines (JBR) cover silo wall heights up to about 3 m. These guidelines presumably overestimate the forces and pressures exerted by silage juice when silo walls are more than 3 m high, which could result in over-sizing, material waste and increased capital costs. This study determined silage physical properties in terms of horizontal wall pressure and evaluated silage juice levels in silos with a wall height of 3 m or more.Wall pressure was measured by transducers m...

  18. Merging silos: collaborating for information literacy.

    Science.gov (United States)

    Miller, Louise C; Jones, Barbara B; Graves, Rebecca S; Sievert, Maryellen Cullinan

    2010-06-01

    Collaborating across disciplines can create additive teaching-learning benefits by bringing together expertise, knowledge, and training from various perspectives. However, there are challenges to effective collaboration that need to be articulated and understood by the partners to develop a useful learning product. In this project, nurse educators and health sciences librarians developed workshops for nurses practicing in community settings. Issues that surfaced reflected a division of content and presentation style along discipline lines. Bringing together expertise involved identifying basic content to present and eliminating extra details, setting the context for learners using a practice example, and alternating handoffs to cover content and practice applications. Effective collaboration requires mutual understanding of discipline-specific information "silos" and shared negotiation of teaching and learning goals.

  19. Selection of plasters and renders for salt laden masonry substrates

    NARCIS (Netherlands)

    Groot, C.; Hees, R.P.J. van; Wijffels, T.J.

    2009-01-01

    The choice of a repair plaster or render by architects often appears to be the result of fortuitous circumstances, such as prior experience with a plaster or a recommendation by a producer. Seldom is the choice based on a sound assessment of the state of the building and the wall that is to be repai

  20. Sodium chloride crystallization in a "salt transporting" restoration plaster

    NARCIS (Netherlands)

    Lubelli, B.; Hees, R.P.J. van; Groot, C.J.W.P.

    2006-01-01

    In recent years several types of restoration plasters, especially developed for salt loaded substrates, have been introduced on the market. The behaviour of these plasters in the field is, however, not always satisfactory. The reasons for failures may be found both in the moisture and salt transport

  1. Investigation of field temperature in moulds of foamed plaster

    Directory of Open Access Journals (Sweden)

    M. Pawlak

    2007-12-01

    Full Text Available Plaster moulds used in precision foundry are characterized by a very low permeability which, in the case of classic plaster moulds, equals to about 0,01÷0,02 m2/(MPa·s. One of the most effective methods for increasing the permeability is a foaming treatment. Another characteristic feature of plaster is its very good insulating power which has influence on the process of solidification and cooling of a cast and also on a knock-out property. This insulating power is a function of thermophysical properties of plaster which, in turn, depend mainly on the mineralogical composition of the mould material, its bulk density as well as on the temperature of the pouring alloy. In the case of a foamed plaster mould an increase of the degree of foaming increases its porosity which causes a change in its thermophysical properties, thereby increasing susceptibility of the mass to overheating. The susceptibility of the plaster layer surrounding the cast to overheating is favorable because it makes it easier to knock-out of the cast by immersing the hot mould in cold water. Thermal and phase tensions that are created during this process cause fast destruction of plaster. This paper describes our investigations aimed at the determination of the dependence of the mould temperature field on the time of the cast stay in the mould, as recorded in a process of an unsteady heat flow. The determined data were planned to be used for estimation of the technological properties of the plaster mould. The tests were carried out using the plaster α-Supraduro and Alkanol XC (foaming agent. The test mould had a diameter of Ø 120 mm with centrally situated mould cavity of Ø 30 mm. Plaster moulds with a degree of foaming 20; 32,5 and 45% and comparatively from non-foaming plaster were tested and their temperatures were measured at the distance x=2; 9; 21; 25;27; 30 mm from the mould cavity within 25 min. Analysis of the results leads to the conclusion, that the highest

  2. Fernald Silos 1 & 2 Accelerated Waste Retrieval Program Surrogate Development

    Energy Technology Data Exchange (ETDEWEB)

    Mullen, O Dennis; Erian, Fadel F.

    2002-09-01

    Whitepaper describing the rationale and methodology for development of surrogates to be used for testing retrieval and processing systems for the DOE Fernald Silos 1 & 2 wastes. One significant updating/revision is expected.

  3. Development of Latent Heat Storage Phase Change Material Containing Plaster

    Directory of Open Access Journals (Sweden)

    Diana BAJARE

    2016-05-01

    Full Text Available This paper reviews the development of latent heat storage Phase Change Material (PCM containing plaster as in passive application. Due to the phase change, these materials can store higher amounts of thermal energy than traditional building materials and can be used to add thermal inertia to lightweight constructions. It was shown that the use of PCMs have advantages stabilizing the room temperature variations during summer days, provided sufficient night ventilation is allowed. Another advantage of PCM usage is stabilized indoor temperature on the heating season. The goal of this study is to develop cement and lime based plaster containing microencapsulated PCM. The plaster is expected to be used for passive indoor applications and enhance the thermal properties of building envelope. The plaster was investigated under Scanning Electron Microscope and the mechanical, physical and thermal properties of created plaster samples were determined.

  4. Development of Latent Heat Storage Phase Change Material Containing Plaster

    Directory of Open Access Journals (Sweden)

    Diana BAJARE

    2016-05-01

    Full Text Available This paper reviews the development of latent heat storage Phase Change Material (PCM containing plaster as in passive application. Due to the phase change, these materials can store higher amounts of thermal energy than traditional building materials and can be used to add thermal inertia to lightweight constructions. It was shown that the use of PCMs have advantages stabilizing the room temperature variations during summer days, provided sufficient night ventilation is allowed. Another advantage of PCM usage is stabilized indoor temperature on the heating season. The goal of this study is to develop cement and lime based plaster containing microencapsulated PCM. The plaster is expected to be used for passive indoor applications and enhance the thermal properties of building envelope. The plaster was investigated under Scanning Electron Microscope and the mechanical, physical and thermal properties of created plaster samples were determined.

  5. Horizontal Bulk Material Pressure in Silo Subjected to Impulsive Load

    OpenAIRE

    Radosław Tatko; Sylwester Kobielak

    2008-01-01

    This paper describes laboratory tests carried out in the steel flat-bottomed silo model filled with sand, subjected to external dynamic loads. The model was placed on a system of springs, which represent subsoil. The loads in the form of horizontal impulses were applied to the bottom plate of the silo. Horizontal pressure-time courses were used to analyze the influence of subsoil vibrations on the distribution changes of these pressures. Basic conclusion: (1) the subsoil vibrations cause two ...

  6. Analysis of steel silo structures on discrete supports

    OpenAIRE

    Li,Hongyu

    1994-01-01

    The objective of this thesis is to broaden current knowledge of the strength and buckling/collapse of shells, with special reference to steel silo structures on discrete supports, and thus to provide design guidance of practical value for future silo design and construction and to develop new research aspects for further investigation. A linear elastic solution of the cylindrical shell bending equations is presented for local loadings, with special attention to local longitudinal distri...

  7. Silos. Un milenio. Actas del congreso Internacional sobre la Abadía de Santo Domingo de Silos. [Reseña

    OpenAIRE

    Labarga-García, F. (Fermín)

    2005-01-01

    Reseña de: Saturnino LÓPEZ SANTIDRIÁN, Silos. Un milenio. Actas del congreso Internacional sobre la Abadía de Santo Domingo de Silos, Universidad de Burgos-Abadía de Silos («Studia Silensia» XXV, I: Espiritualidad), Burgos 2003, 542 pp.

  8. Moisture and salt transport in three-layer plaster/substrate systems

    NARCIS (Netherlands)

    Petković, J.; Huinink, H.P.; Pel, L.; Kopinga, K.; Hees, R.P.J. van

    2010-01-01

    We have investigated whether a plaster which has two plaster layers with different pore sizes can act as a salt accumulating plaster system, in which salt crystallizes in the base layer of the plaster and not in the substrate or at the external surface. We used two substrates; fired-clay brick and B

  9. Problems with plastered external heat insulation. Probleme mit verputzter Aussenwaermedaemmung

    Energy Technology Data Exchange (ETDEWEB)

    Epple, H.; Foglia, A.; Preisig, H.; Pfefferkorn, J.

    1984-01-01

    Concerning execution, maintenance and service life, walls with plastered external heat insulation constitute an economic method. Owing to experience gained with plastered external heat insulation, it is possible today to provide reliable information on requirements made on ground material and operational execution. The author intends to contribute to a prevention of defects by giving concise examples. A survey on different types of external heat insulation is followed by a treatment of the problem areas of roof-edge connection, base end under ground, modernization of old buildings and cracks in plaster. Principal statements are made concerning steam diffusion, planning, materials and execution.

  10. Dilatometric examination of moulds with plaster binder

    Directory of Open Access Journals (Sweden)

    M. Nadolski

    2011-01-01

    Full Text Available Investigations concerning thermal expansion of moulding materials with plaster binder have been performed for two mixture compositionsof Authors’ own design, as well as for the material used in jewellery industry under the Prima-Cast trade name, and for ThermoMold 1200moulding material. The results of dilatometric examinations of these materials, carried out within the temperature range from about 20°Cto 650°C by means of the DA-3 automatic dilatometer, have been compared. An analysis of this comparison has revealed that it is thematrix composition which is decisive for the magnitude of dimensional changes of moulds, and that applying components which do notexhibit polymorphic transformations reduces dimensional changes of a mould during its thermal treatment.

  11. An assessment of gases in oxygen-deficient hay silos and the effects of forced ventilation.

    Science.gov (United States)

    Kedan, G; Spielholz, P; Sjostrom, T; Trenary, B; Clark, R E

    2007-01-01

    Many modern tower silos used in the agricultural industry for hay and grain storage are oxygen-limiting by design. Forced-air ventilation using a forage blower is a method commonly used to decrease concentrations of toxic and asphyxiant gases and to increase the O2 content within a silo headspace prior to worker entry. This article describes the methods used to measure gas concentrations and the results obtained from a pilot study by the Washington Fatality Assessment and Control Evaluation (FACE) program of two oxygen-limiting forage tower silos in eastern Washington State. The silos were monitored for oxygen (O2), nitrogen dioxide (NO2), and carbon dioxide (CO2). Measured O2 concentrations were low in all areas of the headspaces monitored for both silos. After beginning forced-air ventilation, O2 concentrations within the silo headspace returned to ambient levels within 8 to 20 min. Nitrogen dioxide levels exceeded the Washington Industrial Safety and Health Act (WISHA) short-term exposure limit (STEL) in the silo that was filled six days earlier (silo 2), but not in the silo that was filled four days earlier (silo 1). The NO2 concentration in silo 2 decreased to below the WISHA STEL within 15 min of starting ventilation but began to rise shortly after ventilation was stopped. Carbon dioxide, which was only measured in silo 1, was detected at 2% within the headspace of this silo. The carbon dioxide concentration decreased to <1% within 3 min of starting ventilation.

  12. Onset of silo collapse under gravity-driven granular discharges

    Science.gov (United States)

    Colonnello, Claudia; Gutiérrez, Gustavo; Reyes, Leonardo; Brau, Fabian; Clément, Eric

    2015-03-01

    Thin walled silos exhibit a critical filling height, Lc, above which the lateral wall buckles as a consequence of the frictional forces exerted by the grains during the granular discharge, producing a catastrophic failure of the structure. We use laboratory scale silos made of paper to study this process experimentally. Based on the observation of the deformation pattern that develops on the silo wall during the discharge, we have proposed a criterion for determining the time of onset of collapse, allowing us to study the conditions under which the collapse is triggered. In particular, we study the behavior of the grains in contact with the wall during the time interval before failure occurs and find that, according to this criterion, the collapse is triggered before a maximal mobilization of the grain-to-wall effective friction force is reached. This can be related to a theoretical model which treats the silo as a thin cylindrical shell subjected to an axial stress with the profile predicted by Janssen's model for the stresses in a silo filled with a granular material. This model predicts correctly the experimental scaling of Lc with various parameters of the system.

  13. Efficacy of heat treatment for disinfestation of concrete grain silos.

    Science.gov (United States)

    Opit, G P; Arthur, F H; Bonjour, E L; Jones, C L; Phillips, T W

    2011-08-01

    Field experiments were conducted in 2007 and 2008 to evaluate heat treatment for disinfestations of empty concrete elevator silos. A Mobile Heat Treatment Unit was used to introduce heat into silos to attain target conditions of 50 degrees C for at least 6 h. Ventilated plastic containers with a capacity of 100 g of wheat, Triticum aestivum L., held Rhyzopertha dominica (F.) (Coleoptera: Bostrichidae) and Tribolium castaneum (Herbst) (Coleoptera: Tenebrionidae). Polyvinyl chloride containers with a capacity of 300 g of wheat held adults of Liposcelis corrodens (Heymons) (Psocoptera: Liposcelididae) and Liposcelis decolor (Pearman), which were contained in 35-mm Petri dishes within the grain. Containers were fastened to a rope suspended from the top of the silo at depths of 0 m (just under the top manhole), 10 m, 20 m, and 30 m (silo floor). When the highest temperature achieved was approximately 50 degrees C for 6 h, parental mortality ofR. dominica and T. castaneum, and both psocid species was 98-100%. Progeny production of R. dominica occurred when there was parental survival, but in general R. dominica seemed less impacted by the heat treatment than T. castaneum. There was 100% mortality of L. corrodens at all depths in the heat treatments but only 92.5% mortality for L. decolor, with most survivors located in the bioassay containers at the top of the silo. Results show wheat kernels may have an insulating effect and heat treatment might be more effective when used in conjunction with sanitation and cleaning procedures.

  14. Exothermic properties of plaster-synthetic composite casts.

    Science.gov (United States)

    Burghardt, Rolf D; Anderson, John G; Reed, Rob A; Herzenberg, John E

    2014-03-01

    Plaster casts can cause burns. Synthetic casts do not. Composite plaster-synthetic casts have not been thoroughly evaluated. This study analyzed the temperature from plaster casts compared with composite casts in a variety of in vitro conditions that would simulate clinical practice. A Pyrex cylinder filled with constant body temperature circulating water simulated a human extremity. Circumferential casts, of either plaster or composite construction (plaster inner layer with outer synthetic layer), were applied to the model. Peak temperatures generated by the exothermic reactions were studied relative to the following variables: dip water temperature (24 °C versus 40 °C), cast thickness (16, 30, and 34 ply), and delayed (5-min) versus immediate application of the synthetic outer layers. Peak temperatures from the all-plaster casts were compared with the composite casts of the same thickness. Finally, the relative cast strength was determined. Potentially dangerous high temperatures were measured only when 40 °C dip water was used or when thick (30- or 34-ply) casts were made. Cast strength increased with increasing cast thickness. However, the presence of synthetics in the composite casts layers did not increase cast strength in every case. When applying composite casts, the outer synthetic layers should be applied several minutes after the plaster to minimize temperature rise. Composite casts do not routinely generate peak temperatures higher than plaster casts of similar thickness. Because the skin of children and the elderly is more temperature-sensitive than average adult skin, extra care should be taken to limit the exothermic reaction when casting children and the elderly: clean, room temperature dip water, minimal required cast thickness, avoidance of insulating pillows/blankets while the cast is drying.

  15. [Study of the stability of current plaster substitutes].

    Science.gov (United States)

    Wruhs, O

    1986-06-01

    In connection with company independent test series the clinically required usefulness of four different modern plaster substitutes were examined. A comparison of breakage resistance, deformation and relation of price versus stability of plaster bandages were considered. The advantage of using these materials, especially in case of prolonged cast immobilization, is-despite of higher financial costs - more appropriate because of lower weight, increased durability and hygienical comfort for the patients.

  16. Steel silos for particulate solid materials : part 2 - membrane forces at filling and discharge.

    OpenAIRE

    Petrovčič, Simon; Guggenberger, Werner; Brank, Boštjan

    2009-01-01

    In the paper, the expressions for membrane forces in an axisymmetric steel silo structure at filling and discharge with a particulate solid material are presented. Graphical plots of these expressions are given. They can be used for a quick and easy estimate of membrane forces distribution in all parts of a silo structure. The plots are valid for any silo geometry and for any material stored. The influence of silo geometry and stored material properties on the size and distribution of membran...

  17. Steel silos for particulate solid materials. Part 1, Actions at filling and discharge.

    OpenAIRE

    Petrovčič, Simon; Guggenberger, Werner; Brank, Boštjan

    2009-01-01

    In the paper, the expressions for membrane forces in an axisymmetric steel silo structure at filling and discharge with a particulate solid material are presented. Graphical plots of these expressions are given. They can be used for a quick and easy estimate of membrane forces distribution in all parts of a silo structure. The plots are valid for any silo geometry and for any material stored. The influence of silo geometry and stored material properties on the size and distribution of membran...

  18. The Investigation with ANSYS of Stress Changes on Silo Wall According to Different Standards

    OpenAIRE

    KİBAR, Hakan; Öztürk,Turgut

    2013-01-01

    In this study, the optimal dimensions of the silo were investigated for barrel-type cylinder, conical outlet, steel construction silo which used in Tombul hazelnut storage in the Giresun province conditions. 10, 11, 12, 13, 14, 15 ve 20 mm wall thickness for 1635 tons storage capacity silo were examined in the study. For this purpose, pressure loads acting on the silo wall surface (vertical, horizontal, friction traction pressure load) using Eurocode 1 and Australian standards were calculated...

  19. THE STRUCTURAL ANALYSIS OF STEEL SILOS WITH CYLINDRICAL-WALL BEARING AND PROFILE-STEEL BEARING

    OpenAIRE

    Zhengjun Tang; Daibiao Zhou; Chenwei Peng; Wenping Wu

    2015-01-01

    The silos are widely used in bulk material in many fields such as agriculture, mining, chemical, electric power storage, etc. Thin metal cylindrical silo shells are vulnerable to buckling failure caused by the compressive wall friction force. In this paper, the structural analysis of two types of steel silo with cylindrical-wall bearing and profile-steel bearing is implemented by Abaqus finite element analysis. The results indicate that under the same loading conditions, steel silos with prof...

  20. Horizontal Bulk Material Pressure in Silo Subjected to Impulsive Load

    Directory of Open Access Journals (Sweden)

    Radosław Tatko

    2008-01-01

    Full Text Available This paper describes laboratory tests carried out in the steel flat-bottomed silo model filled with sand, subjected to external dynamic loads. The model was placed on a system of springs, which represent subsoil. The loads in the form of horizontal impulses were applied to the bottom plate of the silo. Horizontal pressure-time courses were used to analyze the influence of subsoil vibrations on the distribution changes of these pressures. Basic conclusion: (1 the subsoil vibrations cause two types of changes of the horizontal pressures: stable changes which are observed when the model vibrations finish and cyclic of short duration (brief changes; (2 the subsoil vibrations either generate stable increase or stable decrease of the pressures from before vibrations or do not generate any essential stable change; (3 the cyclic dynamic changes of the horizontal pressures depend on the direction of the silo wall displacements and they are the function of the values of these displacements.

  1. [The antalgic and antiphiogistic function and mechanism of RGDT plaster].

    Science.gov (United States)

    Liu, Xiao-Xia; Wang, Zhi-wang; Chien, Xiao-pin; Liu, Cai-min; Tuo, Hai-yan

    2015-09-01

    To study the antalgic and antiphlogistic functions and mechanism of ronggudingtong (RGDT) plaster (traditional Chinese medicine). The painful models were established with hot plate test or acetic acid writhing and the inflammatory models were established with daubing dimethylbenzene on auricle or injecting formaldehyde in toe or synovial envelope to study the antalgic and antiphlogistic functions of RGDT Plaster. The total protein and leukotriene B4(LTB4) in inflammatory exudate were detected to investigate the antalgic and antiphlogistic mechanism of RGDT plaster. The mice were randomly divided into different groups (n = 11), on the basis of drug using, the indexes of pain threshold, swelling degree were observed. Sixty-six mice were used to establish gasbag synovitis model and randomly divided into normal control group,model control group, positive control group (Voltaren gel 0.8 mg/d)and low/medium/high dosage RGDT plaster treating groups(30 mg/d, 60 mg/d, 120 mg/d). 30 mg/d, 60 mg/d,120 mg/d RGDT plaster could upgrade the pain thresholds, remit auricular and foot swelling (P plaster has some antalgic and antiphlogistic functions, and one of the mechanisms is depressing synthesis of LTB4.

  2. 30 CFR 57.16002 - Bins, hoppers, silos, tanks, and surge piles.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Bins, hoppers, silos, tanks, and surge piles... NONMETAL MINES Materials Storage and Handling § 57.16002 Bins, hoppers, silos, tanks, and surge piles. (a) Bins, hoppers, silos, tanks, and surge piles, where loose unconsolidated materials are stored,...

  3. 30 CFR 56.16002 - Bins, hoppers, silos, tanks, and surge piles.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Bins, hoppers, silos, tanks, and surge piles... MINES Materials Storage and Handling § 56.16002 Bins, hoppers, silos, tanks, and surge piles. (a) Bins, hoppers, silos, tanks, and surge piles, where loose unconsolidated materials are stored, handled...

  4. Royal London space analysis: plaster versus digital model assessment.

    Science.gov (United States)

    Grewal, Balpreet; Lee, Robert T; Zou, Lifong; Johal, Ama

    2016-08-10

    With the advent of digital study models, the importance of being able to evaluate space requirements becomes valuable to treatment planning and the justification for any required extraction pattern. This study was undertaken to compare the validity and reliability of the Royal London space analysis (RLSA) undertaken on plaster as compared with digital models. A pilot study (n = 5) was undertaken on plaster and digital models to evaluate the feasibility of digital space planning. This also helped to determine the sample size calculation and as a result, 30 sets of study models with specified inclusion criteria were selected. All five components of the RLSA, namely: crowding; depth of occlusal curve; arch expansion/contraction; incisor antero-posterior advancement and inclination (assessed from the pre-treatment lateral cephalogram) were accounted for in relation to both model types. The plaster models served as the gold standard. Intra-operator measurement error (reliability) was evaluated along with a direct comparison of the measured digital values (validity) with the plaster models. The measurement error or coefficient of repeatability was comparable for plaster and digital space analyses and ranged from 0.66 to 0.95mm. No difference was found between the space analysis performed in either the upper or lower dental arch. Hence, the null hypothesis was accepted. The digital model measurements were consistently larger, albeit by a relatively small amount, than the plaster models (0.35mm upper arch and 0.32mm lower arch). No difference was detected in the RLSA when performed using either plaster or digital models. Thus, digital space analysis provides a valid and reproducible alternative method in the new era of digital records.

  5. Laser triangulation measurement of the level in a coal silo

    Institute of Scientific and Technical Information of China (English)

    Sun Jiping; Jiang Jing

    2011-01-01

    Laser triangulation theory was used to develop a novel contact-free method for measuring the coal level in a silo under harsh environmental conditions found in coal mines,such as the presence of dense dust,high humidity,and low illumination.A laser source and a camera were mounted at the top of the silo.The laser spot projected into the silo was imaged by the camera.The pinhole imaging principle allows the level to be found from the lateral shift of the spot image on the sensor.A pre-calibrated look-up table of the coal depth versus spot position was used to obtain the depth.The measurement accuracy depends on the step size used during pre-calibration.The actual application of a device designed according to these principles shows that it is easy to implement.The detection of the coal level in a silo at the low illumination level found in coal mines is demonstrated.

  6. Promoting Interdisciplinary Collaboration: Trainees Addressing Siloed Medical Education

    Science.gov (United States)

    Kitts, Robert Li; Christodoulou, Joanna; Goldman, Stuart

    2011-01-01

    Objective: Professional siloing within medical institutions has been identified as a problem in medical education, including resident training. The authors discuss how trainees from different disciplines can collaborate to address this problem. Method: A group of trainees from psychiatry, developmental medicine, neurology, and education came…

  7. Destination Attractiveness of the Silos and Smokestacks National Heritage Area

    Science.gov (United States)

    Choi, Puyong

    2012-01-01

    The purpose of this study was to identify the characteristics of destination attractiveness of the Silos and Smokestacks National Heritage Area (SSNHA) in Iowa using the relative attractiveness and importance of the 15 attributes identified by Gearing, Swart, and Var's (1974) scale and 3 attributes identified by Hu and Ritchie (1993). These…

  8. Destination Attractiveness of the Silos and Smokestacks National Heritage Area

    Science.gov (United States)

    Choi, Puyong

    2012-01-01

    The purpose of this study was to identify the characteristics of destination attractiveness of the Silos and Smokestacks National Heritage Area (SSNHA) in Iowa using the relative attractiveness and importance of the 15 attributes identified by Gearing, Swart, and Var's (1974) scale and 3 attributes identified by Hu and Ritchie (1993). These…

  9. Empirically based gamma-distributed random wall pressure field in silo

    DEFF Research Database (Denmark)

    Ditlevsen, Ove Dalager; Berntsen, Kasper Nikolaj

    1999-01-01

    Measurements show that silo wall pressures exhibit large fluctuations in time and space during discharge of the silo. This observation is important for the design of the silowall because spatial pressure variations may impose substantial bending moments in the silo wall that otherwise may be small...... or vanishing do to the carrying ability of the membrane forces in the silo wall. Information about the stochastic properties of this pressure variation cannot be obtained from any existing continuum model for the silo medium flowing within the confinement of the silo walls. Therefore the modeling must...... presently be tied to statistical analysis of the empirical evidence combined with simple mechanical rinciples. It is shown that an explicitely constructed gamma distribution type of field in equilibrium with itself fits well to themeasurements made in the Swedish Karpalund silo....

  10. On the use of plate-type normal pressure cells in silos

    DEFF Research Database (Denmark)

    Ramirez, Alvaro; Nielsen, Jørgen; Ayuga, F.

    2010-01-01

    Pressure cells are measuring devices commonly used in silo research to study loads exerted by a granular material stored against a silo wall. The design of normal pressure cells for use in an experimental silo research project is critical, mainly because measuring errors complicate...... the interpretation of results. Once the cells have been delivered from the manufacturer to the researcher, they should be calibrated and validated with reference to the measurement of pressure from a granular material against a silo wall. Two related papers deal with a specific plate-type normal pressure cell...... for use in an installation of three full-scale steel silos with different hopper eccentricities (concentric, half-eccentric and full-eccentric) as part of a silo research project. It was found to be necessary to validate the performance of the cells when measuring pressures in the silos in order to arrive...

  11. Mortality among unionized construction plasterers and cement masons.

    Science.gov (United States)

    Stern, F; Lehman, E; Ruder, A

    2001-04-01

    Plasterers perform a variety of duties including interior and exterior plastering of drywall, cement, stucco, and stone imitation; the preparation, installation, and repair of all interior and exterior insulation systems; and the fireproofing of steel beams and columns. Some of the current potential toxic exposures among plasterers include plaster of Paris, silica, fiberglass, talc, and 1,1,1-trichloroethylene; asbestos had been used by the plasterers in the past. Cement masons, on the other hand, are involved in concrete construction of buildings, bridges, curbs and gutters, sidewalks, highways, streets and roads, floors and pavements and the finishing of same, when necessary, by sandblasting or any other method. Exposures include cement dust, silica, asphalt, and various solvents. Proportionate mortality ratios (PMRs) and proportionate cancer mortality ratios (PCMRs) were calculated for 99 causes of death among 12,873 members of the Operative Plasterers' and Cement Masons' International Association who died between 1972 and 1996 using United States age-, race-, and calender-specific death rates. Statistical significance (P value) of results was based upon the Poisson distribution. Among plasterers, statistically significant elevated mortality was observed for asbestosis, where the PMR reached 1,657 (P < 0.01) with eleven observed deaths and less than one death expected, for lung cancer (PCMR = 124, P < 0.01), and for benign neoplasms (PMR = 210, P < 0.05). Among cement masons, statistically significant elevated mortality was observed for cancer of the stomach (PCMR = 133, P < 0.01), benign neoplasms (PMR = 132, P < 0.01), and poisonings (PMR = 159, P < 0.05). Except for poisonings, which were not thought to be occupationally related, all of the statistically significant results occurred among those members who entered the union prior to 1950. However, the risk for lung cancer among plasterers was still elevated among those entering the union after 1970 as was the

  12. [Transdermal behavior of effective constituents in xuanbi gel plaster].

    Science.gov (United States)

    Liu, Yuehuan; Lu, Yang; Du, Shouying; Bai, Jie; Wang, Yue; Li, Huiyun

    2012-05-01

    To study the transdermal absorbability of gentiopicroside, naringin and protosappanin B contained in Xuanbi gel plaster. The Franz diffusing cells method was adopted for the in vitro model of rat belly skins. Three indexes, gentiopicroside, naringin and protosappanin B, residued in the accept liquid, skins and plaster were determined by HPLC. The penetration rates of gentiopicroside, naringin and protosappanin B were respectively 3.47, 1.59, 2.13 microg x cm(-2) x h(-1). After 24 h, their penetration rates were 25.42%, 11.73%, 17.78%, respectively. The residual quantities of gentiopieroside, naringin and protosappanin B in skin were 0.231, 0.593, 0.568 microg x cm(-2), ith the retention rates of 0.027%, 0.227%, 0.475%, respectively. The amount of residue of gentiopicroside, naringin and protosappanin B in plaster were 2179, 674, 278 microg, with the retention rates of 81.36%, 81.92%, 73.83%, respectively. The in vitro transdermal behavior of Xuanbi gel plaster is close to a zero-order process. The residual quantity the retention rate in skins is much lower than the penetration rate and the residual rate in plaster.

  13. Accuracy of stereolithographically printed digital models compared to plaster models.

    Science.gov (United States)

    Camardella, Leonardo Tavares; Vilella, Oswaldo V; van Hezel, Marleen M; Breuning, Karel H

    2017-03-30

    This study compared the accuracy of plaster models from alginate impressions and printed models from intraoral scanning. A total of 28 volunteers were selected and alginate impressions and intraoral scans were used to make plaster models and digital models of their dentition, respectively. The digital models were printed using a stereolithographic (SLA) 3D printer with a horseshoe-shaped design. Two calibrated examiners measured distances on the plaster and printed models with a digital caliper. The paired t test was used to determine intraobserver error and compare the measurements. The Pearson correlation coefficient was used to evaluate the reliability of measurements for each model type. The measurements on plaster models and printed models show some significant differences in tooth dimensions and interarch parameters, but these differences were not clinically relevant, except for the transversal measurements. The upper and lower intermolar distances on the printed models were statistically significant and clinically relevant smaller. Printed digital models with the SLA 3D printer studied, with a horseshoe-shaped base made from intraoral scans cannot replace conventional plaster models from alginate impressions in orthodontics for diagnosis and treatment planning because of their clinically relevant transversal contraction.

  14. Thermophysical properties of hydrophobised lime plasters - The influence of ageing

    Science.gov (United States)

    Pavlíková, Milena; Zemanová, Lucie; Pavlík, Zbyšek

    2017-07-01

    The building envelope is a principal responsible for buildings energy loses. Lime plasters as the most popular finishing materials of historical buildings and culture monuments influence the thermal behaviour as well as construction material of masonry. On this account, the effect of ageing on the thermophysical properties of a newly designed lime plasters containing hydrophobic admixture is analysed in the paper. For the comparative purposes, the reference lime plaster is tested. The ageing is accelerated with controlled carbonation process to simulate the final plasters properties. Basic characterization of the tested materials is done using bulk density, matrix density, and porosity measurements. Thermal conductivity and volumetric heat capacity are experimentally assessed using a transient impulse method. The obtained data revealed the significant changes of the both studied thermal parameters in the dependence on plasters composition and age. The assessed material parameters will be stored in a material database, where will find use as an input data for computational modelling of heat transport in this type of porous building materials and evaluation of energy-savings and sustainability issues.

  15. Silo and method for the stacking of material into and reclaiming of material from such a silo

    NARCIS (Netherlands)

    Van Seters, S.M.; Gerstel, A.W.

    1998-01-01

    The invention relates to a silo comprising a vertical wall (1), a roof (2), a central column (4) and a freely rotatable intermediate bin (3) between the roof and the central column, the intermediate bin being equipped with a feeder screw (5), and also a telescopic chute (ef) which is positioned on t

  16. Does cutting a plaster window weaken its strength?

    Science.gov (United States)

    Patel, Nimesh; Wilson, Lance; Wansbrough, Guy

    2017-03-01

    A plaster window is usually created over a pressure area, or in some cases a wound or suture line. This can relieve pressure at the site, and provide an opportunity to change dressings, check on drainage, and inspect a wound or ulcer. There is concern that this can have an effect on its function to provide fracture stability, and weakens the plaster. The biomechanical effects of windowing on plaster strength were therefore investigated, as it has not previously been reported. A laboratory study was undertaken to compare the bending, kinking and torsion loads withstood by standardised Plaster of Paris (POP), Softcast and Fibreglass casts compared to those with a 60×40mm window fabricated in the centre at clinically defined endpoints using an Instron machine. The addition of a window significantly weakened the load to failure of POP; Fibreglass, and Softcast by 23.1% (473.1N); 25.9% (401.8N), and 29% (146.6N) respectively, during the 4-point bending tests. During the 3-point kinking tests, load to failure was reduced by 38.5% (297.8N); 35.3% (146.9N), and 51.5% (103.8N) respectively. All tests were checked for consistency and carried out in a single orthogonal plane for ease of comparison. The addition of a 60×40mm window to a cast made up of POP, Fibreglass or Softcast weakens the cast load to failure by up to 51% against a 3-point loading force. Though windowing of casts is necessary in certain situations, we advise precautions such as adding further layers of plaster to the window site, keeping the window as small as possible, and advising the patient of the increased risk of weakening and failure of the plaster so that they can take more care. Copyright © 2017 Elsevier Ltd. All rights reserved.

  17. Fermentation characteristics of corn forage ensiled in mini-silos.

    Science.gov (United States)

    Cherney, D J R; Cherney, J H; Cox, W J

    2004-12-01

    To evaluate numerous experimental variables and their interactions involving different corn (Zea mays, L.) silage hybrids, scaled down mini-silos are necessary. Objectives of this study were to evaluate the influence of sample size on pH, NH3, and volatile fatty acid profile of 8 corn silage hybrids, selected to vary in fiber digestibility and ensiled in vacuum-sealed polyethylene bags for 90 d, and to assess the suitability of these mini-silos for detecting differences among corn silage samples. Hybrids were grown at the Cornell Teaching and Research Center located near Harford, NY, and harvested at a dry matter content of about 32% in the fall of 2002. Samples from 3 field replications of each hybrid were chipper-shredder chopped and vacuum-ensiled in bags with sample sizes of 50, 100, 200, 400, and 600 g. Increasing sample size resulted in decreased lactic acid, acetic acid, total acids, and NH3. Most of the difference among sample sizes occurred between the 50- and 100-g sample sizes. Lactic acid:acetic acid ratio (3.1 +/- 0.13) and pH (3.9 +/-0.08) did not vary among sample sizes. There was no detectable butyric acid in the samples. Fermentation characteristics suggested that all samples were well ensiled but that the fermentation profile of the 50-g samples differed the most from other sample sizes. Hybrids did vary in lactic acid, acetic acid, lactic acid:acetic acid, and pH. Differences among hybrids were also noted for dry matter and crude protein. Field-chopped corn hybrids that were ensiled using mini-silos had higher acids than corresponding field-chopped corn hybrids ensiled in Ag-bags, in part due to no effluent escaping from the mini-silos. It is possible to use vacuum-sealed plastic bags to ensile corn, with samples as small as 200 g, and to use these mini-silos to assess differences among corn silage samples. Caution should be used when extrapolating mini-silo data to field-scale ensiling.

  18. Silo clogging reduction by placing an obstacle above the outlet

    Science.gov (United States)

    Lozano, C.; Zuriguel, I.; Janda, A.; Garcimartín, A.; Arévalo, R.; Maza, D.

    2013-06-01

    We present an experimental study of the effect that an obstacle above the outlet of a silo has on the clogging probability. Both, the size of the orifice and the obstacle position are varied for a chosen obstacle size and shape. If the position of the obstacle is properly selected the clogging probability can be importantly reduced. Indeed, as the outlet size is increased - and we approach the critical size above which there is not clogging - the obstacle effect is enhanced. For the largest outlet size studied, the clogging probability is reduced by a factor of more than one hundred. We will show, using numerical simulations, that the physical parameter behind the reduction of the silo clogging seems to be the decrease of the vertical pressure at the outlet proximities.

  19. CONVERSE STAR CHEVRON Silo Mid%活力典范

    Institute of Scientific and Technical Information of China (English)

    铁铁

    2011-01-01

    匡威最新推出滑板鞋款STAR CHEVRON Silo Mid。STAR CHEVRON Silo Mid拥有多款时尚配色,雅致含蓄的橙红加灰还是石青配白?遵从自己性格惯性还是来—次审美习惯的颠覆?摇滚死忠肯定不能放过黑红这一经典组合,神秘凝重的黑色加上妖娆热情的暗红,霸气外露。无论是路人还是滑手都能体会到它所彰显出的活力,那股躁动的气息也将时刻刺激你的每—处感官。

  20. Extension of silo discharge model based on discrete element method

    Energy Technology Data Exchange (ETDEWEB)

    Oldal, Istvan; Safranyil, Ferenc [Szent Istvan University, Goedoelloe (Hungary)

    2015-09-15

    Silos are containers used by almost all fields of industry for storing granular materials and generally classified in two types: mass flow and funnel flow. One of the most important design parameter of these equipment is the discharge rate which depends on the flow mode. There are high numbers of analytical and empirical models used for determine this parameter, however none of them is suitable for both flow modes; moreover the accuracy of mass flow models is not acceptable. Recently a few numerical discharge models are made for certain geometries; but the applicability of these models in case of different flow modes was not examined. Aim of our work is the creation of an experimentally validated numerical discharge model based on others work and examination of this in term of different flow modes. We prove that our modified model is suitable for determine silos discharge rate independently from flow mode.

  1. Pioneers in Pediatric Psychology: Smashing Silos and Breaking Boundaries.

    Science.gov (United States)

    Wertlieb, Donald

    2016-11-01

    As part of the Pioneers in Pediatric Psychology series, this article provides a brief personal account of my career as a pediatric psychologist. Educational and professional experiences often involved confrontations with silos and boundaries set by traditions limiting understanding and impact on children's healthy development. A pedigree in developmental psychology clashed with identity, guild, and loyalty dimensions of clinical psychology. A research emphasis challenged the emergent harmony of the scientist-practitioner models. The medical center and its silos collided with those of arts and sciences academia. Evolving as an applied developmental scientist specializing in pediatric psychology allowed for a gratifying and meaningful career with a range of scientific, pedagogical, and policy contributions. An abiding orientation toward human rights and social justice sustained progress and generativity. © The Author 2016. Published by Oxford University Press on behalf of the Society of Pediatric Psychology. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

  2. The Material Behavior Of Plastered-Bamboo Wall Towards Lateral Loads

    OpenAIRE

    V. R. R. Hutubessy,; Hrc. Priyosulistyo

    2014-01-01

    This study determined the lateral resistance capacity of the plastered-bamboo wall. The test was carried out on three pieces of plastered-bamboo wall. The first was plastered-bamboo wall without bracing (DP-TB), second was plastered-bamboo wall using bamboo bracing (DP-BB), and the last is a plastered-bamboo wall which uses wiremesh bracing (DP-BK). The static load (monotonic) test method was used to determine the correlation between the lateral resistance and the deflection o...

  3. MDA DS COI Spiral 3 - NOA, SILO and ABAC

    Science.gov (United States)

    2009-06-01

    with vessel of interest (VOI) tag ( CARNIVAL PARADISE). ........................................... 23 Figure 17. ABAC return of the crew information...depicts the Baja Peninsula Channel in GMMS, and the list of vessels on the left illustrates a ship with a VOI tag on it ( CARNIVAL PARADISE), indicating...June 2009 22 MDA DS COI Spiral 3 – NOA, SILO and ABAC - Final Report Figure 16. Ship with vessel of interest (VOI) tag ( CARNIVAL

  4. THE STRUCTURAL ANALYSIS OF STEEL SILOS WITH CYLINDRICAL-WALL BEARING AND PROFILE-STEEL BEARING

    Directory of Open Access Journals (Sweden)

    Zhengjun Tang

    2015-04-01

    Full Text Available The silos are widely used in bulk material in many fields such as agriculture, mining, chemical, electric power storage, etc. Thin metal cylindrical silo shells are vulnerable to buckling failure caused by the compressive wall friction force. In this paper, the structural analysis of two types of steel silo with cylindrical-wall bearing and profile-steel bearing is implemented by Abaqus finite element analysis. The results indicate that under the same loading conditions, steel silos with profile-steel bearing and cylindrical-Wall bearing have similar values in Mises stress, but the steel silo with profile-steel bearing has a smaller radial displacement and a better capability of buckling resistance. Meanwhile, the total steel volumes reduced 8.0% comparing to the steel silo with cylindrical-wall bearing. Therefore, steel soil with profile-steel bearing not only has a less steel volumes but also a good stability.

  5. Auricular-Plaster Therapy for Treatment of IBS

    Institute of Scientific and Technical Information of China (English)

    敖学艳; 王宁

    2004-01-01

    @@ Irritable bowel syndrome (IBS), a disease of the digestive system related to mental factors, is clinically characterized by diarrhea (or alternation of diarrhea and constipation) and abdominal pain. In recent years, the authors have used auricular-plaster therapy plus pressing on the back-shu points to treat IBS, and obtained good therapeutic results.

  6. Roughness of surface of vacuum castings prepared in plaster moulds

    Directory of Open Access Journals (Sweden)

    M. Pawlak

    2011-07-01

    Full Text Available The results of researches on surface roughness of CuSn10 and CuSn5Zn5Pb5 bronzes and aluminum AlSi11 alloy vacuum castings prepared in plaster moulds are presented in this paper. Test samples were cut from stripe castings of dimensions 100x15x1 mm. Surfaces were carefully cleaned with use of soft brush than in ultrasonic washer and dried. Experimental castings were prepared in moulds made of two types of plaster. Cast temperatures were 1120 and 1200°C for bronzes and 700 and 800°C for silumin. Temperatures of the mould were 500 and 600°C for bronzes and 200 and 300°C for aluminum alloy. The roughness measurements were carried out with use of Hommelwerke Tester T1000. The average arithmetic deviation of roughness profile Ra, the ten-point height of irregularities Rz and maximum peak to valley height Rm, were measured.It can be stated, on the base of obtained results, that technology of casting in plaster moulds allows preparation of castings of very low roughness, average Ra=0,88÷1,74μm for bronzes and Ra=0,59÷0,83μm for aluminum alloys. Roughness of the surface depends in fact on the cast material. Type of plaster and casting parameters have negligible influence on it.

  7. [Treatment of persistent postmastectomy pain with 5% Lidocaine medicated plaster].

    Science.gov (United States)

    Cruto, M E; Baricocchi, E; Battistella, M; Bona, F; Giacoletto, G; Iacobellis, A; Moselli, N; Palomba, G; Sardo, E; Savojardo, M; Suita, L; Zocca, E; Debernardi, F

    2015-04-01

    Persistent postmastectomy pain (PPMP) syndrome is characterized by neuropathic pain that develops following surgery in breast cancer patients. The reported incidence of PPMP ranges between 30% and 50% and is estimated to increase as the number of women surviving cancer continues to rise. Though effective, today's drug treatments are poorly tolerated, limiting their use and reducing adherence to therapy. Since neuropathic pain is localized, international guidelines suggest that topical treatment with 5% Lidocaine medicated plaster either alone or combined with systemic drugs can be considered for pain management. In this retrospective study we reviewed the medical records of 11 patients treated with 5% lidocaine medicated plaster for moderate-to-severe PPMP at our institute between November 2013 and October 2014. Analysis showed that treatment with 5% Lidocaine medicated plaster, either alone or in combination with systemic drugs, achieved significant pain control already after the first week of therapy. The effectiveness and tolerability of 5% Lidocaine medicated plaster we observed suggests that it is a viable option in the management of PPMP.

  8. Plastering. Pre-Apprenticeship Phase 2 Training. Student Training Modules.

    Science.gov (United States)

    Hamblen, Ron

    These 20 Student Training Modules on plastering comprise one of nine sets of self-paced learning modules developed for Pre-Apprenticeship Phase 2 Training. (A companion instructor's guide is available separately as CE 031 569.) The modules are designed to impart trade knowledge and skills to the student. Each module contains some or all of the…

  9. No local recurrence of enchondroma after curettage and plaster filling.

    NARCIS (Netherlands)

    Gaasbeek, R.D.A.; Rijnberg, W.J.; Loon, C.J.M. van; Meyers, H.; Feith, R.

    2005-01-01

    INTRODUCTION: The most common treatment of enchondromas is curettage (with or without adjuvant therapy) followed by cancellous bone grafting. To avoid donor-site morbidity of the iliac crest, we applied plaster of Paris as a bone defect filler after curettage of enchondromas. MATERIALS AND METHODS:

  10. Analysis of transport and crystallisation of salts in restoration plasters

    NARCIS (Netherlands)

    Hees, R.P.J. van; Lubelli, B.

    2002-01-01

    For the understanding of the salt crystallisation mechanism in restoration plasters, the understanding of water (moisture) transport is essential, as it is the influence of salts on the water transport. More specifically the drying behaviour, i.e. the moisture / salt transport and distribution durin

  11. The Material Behavior Of Plastered-Bamboo Wall Towards Lateral Loads

    Directory of Open Access Journals (Sweden)

    V. R. R. Hutubessy,

    2014-01-01

    Full Text Available This study determined the lateral resistance capacity of the plastered-bamboo wall. The test was carried out on three pieces of plastered-bamboo wall. The first was plastered-bamboo wall without bracing (DP-TB, second was plastered-bamboo wall using bamboo bracing (DP-BB, and the last is a plastered-bamboo wall which uses wiremesh bracing (DP-BK. The static load (monotonic test method was used to determine the correlation between the lateral resistance and the deflection of plastered-bamboo wall. The monotonic testing was only conducted until the load has experience 20% decrease from peak load. The test results showed that the plastered-bamboo wall using wiremesh bracing had the peak load capacity, energy dissipation, and higher ductility than the plastered-bamboo wall using bamboo bracing. Elastic stiffness of the plastered-bamboo wall using bamboo bracing was 1.27 greater than plastered-bamboo wall using wiremesh bracing. The ultimate load resulted from the experiment of the plastered-bamboo wall with either bamboo or additional wiremeshbracingwas 25.52 kN and 26.37 kN or two times greater than the results of an analysis of the flexural failure based on Subedi method (1991 which was 14.39 kN.

  12. An Experimental Study on Distribution of Vertical Stress in a Silo with a Central Inner Downcomer

    Institute of Scientific and Technical Information of China (English)

    景山; 易江林; 王金福; 汪展文; 金涌

    2002-01-01

    The distribution of vertical stress for both active and passive state in the silo with a central innerdowncomer is reported in this paper. Experimental measurement of the axial distribution of vertical stress for bothactive and passive state in the silo are in good agreement with that predicted by theoretical analysis. The meanaxial stress is reduced due to the presence of the inner downcomer in the silo.

  13. Silos Strength Calculation Analysis%料仓强度计算分析

    Institute of Scientific and Technical Information of China (English)

    林杰

    2012-01-01

    对料仓强度计算过程及塔式容器计算差异进行了分析,并对当前料仓强度计算常用的两个标准进行了比较.%The process and contents of strength calculation for silos were analyzed. It also com pared strength calculation for silos with calculation for column. In the end, the difference between two main codes for silos designing was goven.

  14. On the complexity/criticality of Jamming during the discharge of granular matter from a silo

    CERN Document Server

    Evesque, P

    2011-01-01

    This paper is aimed at pursuing a recent discussion about the comparison between Self-Organised Criticality, the jamming process and the percolation theory in the problem of a silo discharge [I. Zuriguel, A. Garcimartin, D. Maza, L.A.Pugnaloni, J.M.Pastor, "Jamming during the discharge of granular matter from a silo", Phys.Rev.E 71, 051303 (2005)]. Statistics of blocking a silo is investigated from different models: percolation, self organised criticality..

  15. Illustrated Postcards: a look at the silos of the district of Portalegre

    OpenAIRE

    Palmeiro, Alexandra

    2012-01-01

    A colecção de Postais ilustrados com vistas dos silos assume-se como um olhar sobre os silos do distrito de Portalegre. Os silos da EPAC são edifícios francamente distintos. Detentores de uma envergadura que reclama um estatuto, inserem-se na paisagem como monumentos e são pertença do colectivo e da identidade local.

  16. Stochastic stresses in granular matter simulated by dripping identical ellipses into plane silo

    DEFF Research Database (Denmark)

    Berntsen, Kasper Nikolaj; Ditlevsen, Ove Dalager

    2000-01-01

    A two-dimensional silo pressure model-problem is investigated by molecular dynamics simulations. A plane silo container is filled by a granular matter consisting of congruent elliptic particles dropped one by one into the silo. A suitable energy absorbing contact force mechanism is activatedduring...... the granular matter in the silo are compared to thesolution of a stochastic equilibrium differential equation. In this equation the stochasticity source is a homogeneouswhite noise gamma-distributed side pressure factor field along the walls. This is a generalization of the deterministic side pressure factor...

  17. 仓顶对筒仓计算结果的影响分析%Analysis of the effect of silo roof on calculation results of silo

    Institute of Scientific and Technical Information of China (English)

    郭洪盛; 盛宏玉

    2012-01-01

    Cylindrical silos are widely used in industry architecture. Because of the lack of complete and practical methods for calculating the internal force in consideration of the edge effect, the film internal force of most silos is calculated according to the non-moment theory, and the internal forces near the edge are checked. During the design and research, many scholars ignore the influence of silo roof on the calculation results of the silo. In this paper, the silo was simulated by using the finite element software ANSYS. The results reveal that the circumferential stress and normal displacement are reduced when taking the silo roof in the form of girder truss into consideration, but its effect is very little. So in regard to the analysis and design of the silo, the influence of silo roof on the internal force of silo wall can be ignored.%目前在筒仓设计过程中没有一套完整和实用的能考虑边缘效应的内力计算方法,大部分圆形筒仓均按无矩理论计算薄膜内力,并对边缘附近进行内力验算.在设计和研究时,许多学者忽略仓顶对筒仓计算结果的影响.文章采用有限元计算软件ANSYS对筒仓进行模拟分析,结果表明:对桁架梁形式的筒仓,考虑仓顶时能减少仓壁的环向应力和法向位移,但影响幅度不大,故在筒仓设计和分析时可以忽略仓顶对仓壁内力的影响.

  18. Parametric design of silo steel framework of concrete mixing station based on the finite element method and MATLAB

    OpenAIRE

    Long Hui; Huang Changzheng; Li Jing; Liu Feng

    2016-01-01

    When the structure of the silo steel framework of concrete mixing station is designed, In most cases, the dimension parameters, shape parameters and position parameters of silo steel framework beams are changed as the productivity adjustment of the concrete mixing station, but the structure types of silo steel framework will remain the same. In order to acquire strength of silo steel framework rapidly and efficiently, it is need to provide specialized parametric strength computational softwar...

  19. The Utility of Silos and Bunkers in the Evolution of Kinesiology

    Science.gov (United States)

    Kretchmar, R. Scott

    2008-01-01

    Silos and bunkers have been allies in the development of kinesiology for nearly 50 years. Silos of specialization allow us to go toe-to-toe with researchers in parent disciplines, compete for grants, and otherwise spread our academic wings. The bunkers of utility and generic movement provide an important degree of legitimacy for a subject matter…

  20. Discharge flow of a bidisperse granular media from a silo

    Science.gov (United States)

    Benyamine, M.; Djermane, M.; Dalloz-Dubrujeaud, B.; Aussillous, P.

    2014-09-01

    The discharge flow in a cylindrical and a rectangular silo using both monodisperse and bidisperse mixtures of spherical glass beads is studied experimentally. The flow rate is measured using a precision balance for a large range of particle diameters, size ratios, and outlet diameters. A simple physical model is proposed to describe the flow of bidisperse mixtures. It gives an expression for the flow rate and predicts that the bulk velocity follows a simple mixture law. This model implies that a mixture diameter cannot be simply defined. Moreover it is shown that bidisperse granular media allow for the transport of coarse particles below their jamming conditions.

  1. Interdisciplinary evidence-based practice: moving from silos to synergy.

    Science.gov (United States)

    Newhouse, Robin P; Spring, Bonnie

    2010-01-01

    Despite the assumption that health care providers work synergistically in practice, professions have tended to be more exclusive than inclusive when it comes to educating students in a collaborative approach to interdisciplinary evidence-based practice (EBP). This article explores the state of academic and clinical training regarding interdisciplinary EBP, describes efforts to foster interdisciplinary EBP, and suggests strategies to accelerate the translation of EBP across disciplines. Moving from silos to synergy in interdisciplinary EBP will require a paradigm shift. Changes can be leveraged professionally and politically using national initiatives currently in place on improving quality and health care reform.

  2. Efficacy of a new blister prevention plaster under tropical conditions.

    Science.gov (United States)

    Sian-Wei Tan, Shani; Kok, Swee Kuan; Lim, Jeremy Khim Yong

    2008-01-01

    To survey the incidence of blister formation in a group of military recruits and to determine the efficacy of a new commercially available blister prevention plaster (Blist-O-Ban). Questionnaires were completed by 100 male recruits, and the same 100 were entered into a field trial. Due to illness, 2 did not complete the study. Premarch foot condition was documented. Each participant acted as his own control. Foot side and plaster site were randomly selected, and plasters were applied according to a strict protocol. Participants were re-examined for blisters after a 16-km hike with pack, and the condition of the feet was documented. A chi2 test was used to analyze the results. Ninety-eight volunteers with 101 Blist-O-Ban application sites participated. Twenty-seven participants developed a total of 46 blisters. Heel and toe blisters accounted for more than half of all blisters. None of the bandage application sites developed blisters, and 99 out of 101 bandages remained well adhered to the application sites. When applied according to strict protocol, the new blister prevention bandage remained well-adhered to application sites and prevented the formation of foot blisters even in humid tropical conditions.

  3. The thermal analysis and derivative bronzes cast to plaster moulds

    Directory of Open Access Journals (Sweden)

    B. Pisarek

    2009-07-01

    Full Text Available It plaster moulds gets casted the alloys of following metals: Al, Cu, Ag, Au in precise and artistic founding. The investigation of the crys-tallization of bronzes in hot plaster moulds the method of the thermal analysis and derivative (TDA was not realized out so far. Probe TDAg and tripod enabling the execution of measurements on inductive casting machine INDUTHERM-VC 500D were designed for this technology especially. It was confirmed that one the method TDA can identify the crystallization process of the bronze in hot plaster moulds. The investigations of the superficial distribution of the concentration of elements in the microstructure of the studied grades of the bronze on X-ray microanalizer were conducted. It results that they be subject to in bronze CuSn10-C (B10 and the CuSn5Zn5Pb5-C (B555 of strong microsegregation from conducted investigations: Pb, Sn and Sb. The single separates of intermetallic phase κ was identified in the bronze B10 rich first of all in Zn, Sn, Sb and Fe, and two intermetallic phase, one rich were identified in the bronze B555 first of all in Zn, Sb, (Nor, Fe and second rich in Sn, Sb, (Nor, Fe. The most homogeneous microstructure from the bronze CuAl10Fe5Ni5-C (BA1055 is characterizes among the studied grades of the bronze in the cast state.

  4. Vitrification of Simulated Fernald K-65 Silo Waste at Low Temperature

    Energy Technology Data Exchange (ETDEWEB)

    Jantzen, C.M.

    1999-03-15

    Vitrification is the technology that has been chosen to solidify approximately 18,000 tons of geologic mill tailings at the Fernald Environmental Management Project (FEMP) in Fernald, Ohio. The geologic mill tailings are residues from the processing of pitchlende ore during 1949-1958. These waste residues are contained in silos in Operable Unit 4 (OU4) at the FEMP facility. Operable Unit 4 is one of five operable units at the FEMP. Operable Unit 4 is one of five operable units at the FEMP. Operating Unit 4 consists of four concrete storage silos and their contents. Silos 1 and 2 contain K-65 mill tailing residues and a bentonite cap, Silo 3 contains non-radioactive metal oxides, and Silo 4 is empty.

  5. Calculation of k factor function for the carbonation process of lime-based plasters

    Science.gov (United States)

    Pavlíková, Milena; Pokorný, Jaroslav; Pavlík, Zbyšek

    2017-07-01

    The carbonation process of prepared lime plaster and lime based plaster with pozzolana active metakaolin is performed in an accelerated test arrangement. The depth of carbonation head is determined using colorimetric method and FTIR spectroscopy. Based on experimental data of carbonation head, time dependent k factor function is calculated that points to the decelerated and retarded propagation of the carbonation process due to metakaolin used in plaster composition.

  6. Assessment of the Variability of Biogas Production from Sugar Beet Silage as Affected by Movement and Loss of the Produced Alcohols and Organic Acids

    Directory of Open Access Journals (Sweden)

    Ali Heidarzadeh Vazifehkhoran

    2016-05-01

    Full Text Available The biochemical methane potential and composition of sugar beet pulp silage were investigated using samples taken from six different depths in both open and closed silos (height 3.6 m. The biochemical methane potential (BMP of pulp silage in open silos ranged from 337 to 420 normal litre (NL CH4/kg volatile solids (VS, while the BMP of pulp silage in closed silos varied between 411 and 451 NL CH4/kg VS. The biochemical methane potential peaked at a depth of 1.45 m with 420 NL CH4/kg VS for open silos and 451 NL CH4/kg VS for closed silos. The ethanol concentration and biochemical methane potential showed the same trend with depth throughout the silos. The energy loss correlated to the loss of volatile solids, and the depths described a linear relationship between them for both the open and closed silos (R2 = 0.997 for the open silo and R2 = 0.991 for the closed silo. The energy potentials and composition of beet pulp silage were highly stratified and there was a risk that the silage samples were not representative in investigations of biomass quality for energy production.

  7. Models for grains and gas ejection dynamics from a silo

    Science.gov (United States)

    Zhou, Yixian; Aussillous, Pascale; Ruyer, Pierre; Iusti/Gep Team; Semia/Limar Team

    2015-11-01

    In the hypothetical conditions of a reactivity initiated accident in a nuclear power plant, some of the fuel rods could break. If fuel fragmentation occurs, hot fuel particles and pressurized gas could interact with the surrounding fluid. The violence of this interaction depends on the discharge rate toward the fluid. In the present work, we study the discharge dynamics and identify the parameters governing this flow. In this paper, we focus on the experimental study of the discharge of a silo composed of spherical glass beads, with an orifice either lateral or at the bottom, with or without air flow. The measured parameters are the mass flow rate and the pressure along the silo, whereas the controlled parameters are the size of particles, the size of orifices, and the flow rate of air. For the case without air flow we found that the flow rate of particles ejected from the bottom orifice is 3 times greater than from the lateral orifice. For the case of a lateral orifice, when the form of the orifice is rectangular with width W and height D, we identify two regimes which depend on the ratio of width to height W / D . For the case with air flow, we found that the flow rate increases with the air flow. A simple physical model is proposed to describe the grains and gas ejection.

  8. Extinguishing smouldering fires in silos. BRANDFORSK project 745-961

    Energy Technology Data Exchange (ETDEWEB)

    Tuomisaari, M.; Baroudi, D.; Latva, R. [VTT Building Technology, Espoo (Finland). Building Physics, Building Services and Fire Technology

    1998-11-01

    Combustible, porous materials may self-ignite during their storage time in silos as a result of internal heating. The self-ignition process may be slow, and it results in smouldering fires that are extremely difficult to extinguish. Suitable means to fight the smouldering fire were studied both theoretically and experimentally. General heat and mass transfer equations for porous media subject to fires and suppression were written. The equations together with dimensional analysis revealed critical parameters, like the grain size and moisture content, affecting the combustion and suppression process, but they also revealed the complexity of the problem. Experimental results of over 50 tests with varying combustibles and suppression agents were used as the basis for proposed qualitative guidelines on how to fight a smouldering silo fire. Among the potential gaseous agents, CO{sub 2} was found to be the most efficient one. Low expansion foam was also found to be a potential candidate, but its applicability requires further confirmation. Quantifying the guidelines requires a whole new study on the detection of a smouldering fire. The same detection system should be capable of monitoring the suppression process and - most importantly - verifying the extinguishment. (orig.) 46 refs.

  9. Sobrepresiones en las paredes de los silos debidas al vaciado

    Directory of Open Access Journals (Sweden)

    Ravenet, J.

    1975-07-01

    Full Text Available Chronologically the author analyzes the theories and experiences published by the main world specialists on the subject of silos. Further, some of the most important Norms used In various countries are being studied. The compression curves by each author and Norm are drawn, applied to a standard cell. In a diagram all the curves are superimposed and a dispersion of 215% is obtained. This dispersion is due to the fact that many authors leave out the dynamic phenomena produced during the outlet and which have caused so many cracks, deformations and irregularities.El autor analiza cronológicamente las teorías y experiencias emitidas por los principales especialistas mundiales en materia de silos. Se estudian igualmente algunas de las más importantes Normas utilizadas en diversos países. Se trazan las curvas de presiones de cada autor y Norma, aplicadas a una celda estándar. En un gráfico se superponen todas las curvas obtenidas, apareciendo una dispersión del 215%. Esta dispersión se debe a que muchos autores omiten los fenómenos dinámicos producidos durante el vaciado y que tantas grietas, deformaciones y accidentes han ocasionado.

  10. Possibility of reconstruction of dental plaster cast from 3D digital study models

    OpenAIRE

    Kasparova, Magdalena; Grafova, Lucie; Dvorak, Petr; Dostalova,Tatjana; Prochazka, Ales; Eliasova, Hana; Prusa, Josef; Kakawand, Soroush

    2013-01-01

    Objectives To compare traditional plaster casts, digital models and 3D printed copies of dental plaster casts based on various criteria. To determine whether 3D printed copies obtained using open source system RepRap can replace traditional plaster casts in dental practice. To compare and contrast the qualities of two possible 3D printing options – open source system RepRap and commercially available 3D printing. Design and settings A method comparison study on 10 dental plaster casts from th...

  11. Behavior of plasters on the modern heat-effective exterior walls of buildings (rus

    Directory of Open Access Journals (Sweden)

    Babkov V.V.

    2012-12-01

    Full Text Available Physical and mechanical characteristics, the most significant for the plasters with regard to the features of their behavior as the coating of building faces were evaluated. Results of quantitative estimation of stresses in the plaster layers on surfaces of different stiffness due to the plaster shrinkage are given. It is shown that with a decrease of the surface modulus of elasticity, stresses in the plaster coating are decreased either due to reduction of the effect of its deformations’ constraint. By analysis and with experiments it is proved, that the main factor evaluating the ultimate extensibility of the mortar is its viscoelasticity modulus, while mortar strength increase involves its stresses increase.

  12. Deformability of plastering compositions in design solutions of modern thermal protective exterior walls

    Directory of Open Access Journals (Sweden)

    R.R. Vakhitov

    2013-04-01

    Full Text Available In recent years, appearance of new constructive decisions for multilayer thermal efficient walls in the practice of design and construction caused the increasing use of protective and decorative plaster compositions. Comprehensive protective plaster systems nowadays are used in the facade insulation systems as a protective layer on the surface of polystyrene foam or mineral wool boards, forming the insulating layer to the outer walls of concrete blocks. They are also used for exterior finish of walls made of gas-concrete blocks, plastering the brickwork of the buildings operated by rehabilitation, in particular, apartment houses of old mass series. The problem of ensuring durability of thermal efficient external walls with the use of protective and decorative plaster systems were identified in this article. The factors, affecting the resistance of facade plasters to the action of external conditions in operating process were considered. The weaknesses in the necessary characteristics of plaster mixtures provided by material manufacturers are revealed. The existing methods for determining crack resistance of plaster compositions are monitored. The author's method of determining the maximum stretch of plaster compositions is given. The article presents tests results of various plaster compositions, confirming the effectiveness of the proposed method.

  13. Plaster of Paris-Short History of Casting and Injured Limb Immobilzation.

    Science.gov (United States)

    Szostakowski, B; Smitham, P; Khan, W S

    2017-01-01

    Various materials have been used since ancient times to help immobilise fractures. In this review, we discuss the history and developments of these materials as well as plaster of Paris. There has been a recent trend away from non-operative management of fractures, and skills in the use of plaster of Paris are declining. For the successful treatment of patients, it is important to appreciate how plaster works, how it should be used, and what can go wrong. In this review, we also discuss principles of applications and complications of plaster of Paris.

  14. Lidocaine/tetracaine medicated plaster: in minor dermatological and needle puncture procedures.

    Science.gov (United States)

    Croxtall, Jamie D

    2010-11-12

    The lidocaine/tetracaine medicated plaster comprises a lidocaine/tetracaine 70 mg/70 mg patch and a controlled heat-assisted drug delivery pod that increases the diffusion of lidocaine and tetracaine into the dermis. Following a 1-hour application period, systemic absorption of lidocaine or tetracaine from the plaster was minimal. The lidocaine/tetracaine medicated plaster provided effective pain relief for adult (including elderly) patients undergoing minor dermatological procedures and for adult and paediatric patients undergoing vascular access procedures. In randomized, double-blind clinical trials, patient-reported median pain scores were significantly lower with the lidocaine/tetracaine medicated plaster than with an identical plaster containing placebo in patients undergoing minor dermatological or vascular access procedures. Furthermore, patient-reported median pain scores were significantly lower with the lidocaine/tetracaine medicated plaster than with a lidocaine/prilocaine cream in patients undergoing vascular access procedures. In a large, randomized, double-blind trial in paediatric patients undergoing venipuncture, the overall incidence of pain was significantly lower with the lidocaine/tetracaine medicated plaster than with a lidocaine/prilocaine plaster. The lidocaine/tetracaine medicated plaster was well tolerated, with the most frequent treatment-related adverse events resolving spontaneously.

  15. Plaster of Paris–Short History of Casting and Injured Limb Immobilzation

    Science.gov (United States)

    Szostakowski, B.; Smitham, P.; Khan, W.S.

    2017-01-01

    Various materials have been used since ancient times to help immobilise fractures. In this review, we discuss the history and developments of these materials as well as plaster of Paris. There has been a recent trend away from non-operative management of fractures, and skills in the use of plaster of Paris are declining. For the successful treatment of patients, it is important to appreciate how plaster works, how it should be used, and what can go wrong. In this review, we also discuss principles of applications and complications of plaster of Paris. PMID:28567158

  16. Salt damage of stone, plaster and painted layers at a medieval church, South-Hungary

    Science.gov (United States)

    Török, Ákos; Galambos, Éva

    2016-04-01

    The Chapel of Pécsvárad is one of the best preserved and oldest medieval stone monument in South Hungary. It dates back to the 11th century. The interior of the chapel is decorated with wall paintings, which are later and probably originating from the late 12th century. The wall painting is partly preserved and it is located on an interior stone wall of the chapel facing to the East. The wall painting shows various forms of damage from salt efflorescence to chipping. The current research provides information on the in situ and laboratory analyses of salts, plasters, pigments and stone material suggesting mechanisms of decay that lead to partial loss of the painting. Both on site techniques and laboratory analyses were performed. Imaging techniques such as UV luminescence and IR thermography were used to identify the moist and salt covered zones on the wall surface. Portable moisture meter were also applied to map the wet zones in the interior and also at the external part of the chapel. Schmidt hammer and Duroscop were used for testing the surface strength of stone. Laboratory tests were focused on mineralogical and chemical compositional analyses. Small samples of stone, mortar, plaster and pigments were tested by optical microscopy, SEM-EDX, XRD and Thermogravimetric analyses. According to our tests the chapel was predominantly made of porous limestone and sandstone. Laboratory analyses proved that the major salt responsible for the damage of external walls are gypsum and halite, while in the interior part higher amount of halite and significant amount of sodium-nitrate were found besides gypsum. The painted layers are on Byzantine-type of plaster with organic compounds (plant fragments) and with a substrate layer rich in calcium carbonate. The identified pigments are dominantly earth pigments such as iron-oxide containing red and yellow (ochre) and green earth. A unique preservation of ultramarine blue in Hungary was found on the wall painting. The partial

  17. Qualidade de grãos de milho armazenados em silos bolsa Quality of corn grain stored in silo bags

    Directory of Open Access Journals (Sweden)

    André Rodrigues da Costa

    2010-06-01

    Full Text Available A utilização de bolsas seladas hermeticamente é uma alternativa aos métodos tradicionais de armazenagem de grãos em nível de fazenda. Em vista disso, objetivou-se com este trabalho avaliar a qualidade de milho armazenado hermeticamente em silos bolsa. O produto, com teores de água de 14,5 e 18,0% b.u, foi acondicionado em mini-bolsas devidamente seladas nas temperaturas de 25; 30 e 35 ºC. Foram realizadas análises de teor de água, de classificação dos grãos, de massa específica aparente, de percentual de germinação e de condutividade elétrica, no início do armazenamento e após 30; 60; 90; 135 e 180 dias. Verificou-se que não houve variação do teor de água dos grãos de milho armazenados nos silos bolsa. Os grãos de milho foram classificados como Tipo 1 ao longo do período de armazenamento, exceto para os com 18,0% (b.u. de teor de água na temperatura de 35 ºC. Não houve decréscimo significativo da massa especifica aparente do produto ao longo do armazenamento. Em geral, ocorreu decréscimo do percentual de germinação dos grãos de milho armazenados úmidos e secos e acréscimo da condutividade elétrica da solução que continha os grãos, exceto para os armazenados com 14,5% nas temperaturas de 25 e 30 ºC. Conclui-se que é possível armazenar milho em silos bolsa, durante 180 dias, grãos com teor de água de 14,5% (b.u. nas temperaturas de 25; 30 e 35 ºC e grãos com teor de água de 18,0% por 180 dias nas temperaturas de 25 e 30 ºC.Airtight storage in sealed bags provides an alternative to traditional methods for on-farm grain storage. The objective of this work was therefore to evaluate the quality of corn stored in airtight sealed bags. Grain with moisture content (m.c. of about 14.5 and 18.0% (w.b. was properly stored in sealed mini-bags at 25; 30; and 35 ºC. Analyses included moisture content, grain classification, apparent specific mass, percentage of germination and electrical conductivity at the

  18. Possibility of reconstruction of dental plaster cast from 3D digital study models.

    Science.gov (United States)

    Kasparova, Magdalena; Grafova, Lucie; Dvorak, Petr; Dostalova, Tatjana; Prochazka, Ales; Eliasova, Hana; Prusa, Josef; Kakawand, Soroush

    2013-05-31

    To compare traditional plaster casts, digital models and 3D printed copies of dental plaster casts based on various criteria. To determine whether 3D printed copies obtained using open source system RepRap can replace traditional plaster casts in dental practice. To compare and contrast the qualities of two possible 3D printing options--source system RepRap and commercially available 3D printing. A method comparison study on 10 dental plaster casts from the Orthodontic department, Department of Stomatology, 2nd medical Faulty, Charles University Prague, Czech Republic. Each of 10 plaster casts were scanned by inEos Blue scanner and the printed on 3D printer RepRap [10 models] and ProJet HD3000 3D printer [1 model]. Linear measurements between selected points on the dental arches of upper and lower jaws on plaster casts and its 3D copy were recorded and statistically analyzed. 3D printed copies have many advantages over traditional plaster casts. The precision and accuracy of the RepRap 3D printed copies of plaster casts were confirmed based on the statistical analysis. Although the commercially available 3D printing enables to print more details than the RepRap system, it is expensive and for the purpose of clinical use can be replaced by the cheaper prints obtained from RepRap printed copies. Scanning of the traditional plaster casts to obtain a digital model offers a pragmatic approach. The scans can subsequently be used as a template to print the plaster casts as required. Using 3D printers can replace traditional plaster casts primarily due to their accuracy and price.

  19. Degradation of tocopherols during rapeseed storage in simulated conditions of industrial silos

    Science.gov (United States)

    Gawrysiak-Witulska, Marzena; Siger, Aleksander; Rusinek, Robert

    2016-01-01

    The investigations consisted in laboratory simulation of conditions prevailing in the real ecosystem in an industrial rapeseed storage facility. The aim of the study was to assess the impact of temperature, moisture, and static pressure on degradation of tocopherols contained in rapeseed. Rapeseed varieties with high oil content were analysed in the investigations. Samples of seeds with 7, 10, 13, and 16% moisture levels were stored at a temperature of 25, 30, and 35°C in specially designed airtight pressure silos for storage in controlled conditions. During the storage, the seeds were subjected to overpressure in the range of 20-60 kPa. The seeds were stored in these conditions for 28 days. It was demonstrated that primarily moisture induced the greatest loss of the total content of tocopherol and its α-T and γ-T homologues, followed by temperature and, to a lesser extent, pressure. In addition, the results obtained showed that, in the case of seeds characterised by higher moisture levels (13 and 16%), an increase in the storage temperature in the range of 25-30°C rather than 30-35°C intensified tocopherol loss more efficiently.

  20. PCM-enhanced lime plasters for vernacular and contemporary architecture

    Science.gov (United States)

    Theodoridou, Magdalini; Kyriakou, Loucas; Ioannou, Ioannis

    2016-04-01

    In 1997, the European Union (EU) pledged to reduce the amount of greenhouse gas emissions by 20% below the levels of 1990 by the end of 2020. In recent years it has become evident that, in order to reach that goal, EU Member States must take measures to encourage sustainability in the building industry, which is a major energy consumer. Such measures should involve the use of innovative, environmentally friendly materials and methods in new constructions, as well as the renovation of existing properties by upgrading their current state of energy efficiency. Phase Change Materials (PCMs) have the ability to absorb and release thermal energy, in the form of latent heat, during the melting or solidifying processes respectively. Thus, they may be used as additives in the production of thermally efficient composite building materials. A PCM-enhanced plaster is a heat storage medium combining an appropriate PCM with a cementitious or non-cementitious matrix to produce a low-cost thermal storage material with structural and thermostatic properties. Although innovative technologies, such as PCMs, have certainly contributed to the boost in the evolution of the building materials industry in recent years, a significant proportion of these technologies and practices have not yet been fully exploited in materials based on traditional principles. This paper focuses on the design and production of novel cementless PCM-enhanced lime plasters, in line with the traditional production technology of lime composites. The new plasters are produced using either hydrated or natural hydraulic lime binder, crushed calcarenite sand (0-2 mm) and commercial microencapsulated PCM in powder form (5% w/w of solids). Results from comparative tests between reference mixtures and mixtures with the addition of PCM, carried out 28, 56 and 90 days after laboratory production, prove the potential of PCMs in enhancing the thermal performance of traditional lime-based composites. The modified composites

  1. Dependence of effective screening length in granular columns on bead and silo sizes and their ratio

    Institute of Scientific and Technical Information of China (English)

    Abdul Qadir; Madad Ali Shah; Saeed Ahmed Khan

    2013-01-01

    Apparent mass measurements at the bottom of silos have been carried out.An important parameter in the Janssen model known as the effective screening length has been investigated for different bead and silo diameters as well as of their ratios.It is found that the effective screening length augments with the grain diameter d in addition to the granular column size.It is also revealed that λ exhibits stronger correlation with the bead diameter than that of the silo.This phenomenon is attributed to the reduced-shielding of the vertical stresses to the horizontal ones.

  2. Dependence of effective screening length in granular columns on bead and silo sizes and their ratio

    Science.gov (United States)

    Abdul, Qadir; Madad, Ali Shah; Saeed, Ahmed Khan

    2013-05-01

    Apparent mass measurements at the bottom of silos have been carried out. An important parameter in the Janssen model known as the effective screening length has been investigated for different bead and silo diameters as well as of their ratios. It is found that the effective screening length augments with the grain diameter d in addition to the granular column size. It is also revealed that λ exhibits stronger correlation with the bead diameter than that of the silo. This phenomenon is attributed to the reduced-shielding of the vertical stresses to the horizontal ones.

  3. Exploring the Impact of Silos in Achieving Brand Orientation

    DEFF Research Database (Denmark)

    Gyrd-Jones, Richard; Helm, Clive; Munk, Jonas

    Brands are widely recognised as important sources of competitive advantage. The newly emerged concept of brand orientation has be used to assess the extent to which the whole organisation is orientated around the brand and thus the extent to which organisational resources are focused around...... maximising brand potential. Whilst offering potential to improve our understanding of how brands can be effectively managed and offering practitioners a set of tool to this end, this concept is limited in both its empirical and theoretical foundations. Through a case study this paper documents how functional...... silos are associated with different mindsets that create barriers to the achievement of brand orientation. The case follows a medium sized manufacturing company in its efforts to introduce a brand revitalization strategy across the organization. Despite the strategy having top management full support...

  4. Slip-stick excitation and travelling waves excite silo honking

    Science.gov (United States)

    Vriend, Nathalie; Warburton, Kasia; Porte, Elze

    2016-11-01

    Industrial storage silos filled with PET-particles can create a sound upon discharge. The sound forms a nuisance for the environment when the structure starts to act as a loudspeaker and may ultimately result in structural failure. This work investigates the phenomenon experimentally-the deployment of a microphone, an accelerometer and high-speed imaging on a laboratory set-up reveal the driving mechanism for the structural resonance: stick-slip at the wall. Particle image velocimetry shows an asymmetric, upwards travelling wave (at 50 m/s) which contains the dynamic "slip"-region. The frequency of the mechanical motion of the grains is successfully correlated to the frequency of the emitted sound. Friction models are explored to describe and quantify the frictional interaction between the grains and the wall.

  5. Confined granular flow in silos experimental and numerical investigations

    CERN Document Server

    Tejchman, Jacek

    2013-01-01

      During confined flow of bulk solids in silos some characteristic phenomena can be created, such as: —         sudden and significant increase of wall stresses, —         different flow patterns, —         formation and propagation of wall and interior shear zones, —         fluctuation of pressures and, —         strong autogenous dynamic effects. These phenomena have not been described or explained in detail yet. The main intention of the experimental and theoretical research presented in this book is to explain the above mentioned phenomena in granular bulk solids and to describe them with numerical FE models verified by experimental results.

  6. Effect of paint on vapour resistivity in plaster

    Directory of Open Access Journals (Sweden)

    de Villanueva, L.

    2008-12-01

    Full Text Available The vapour resistivity of plaster coatings such as paint and their effectiveness as water repellents were studied in several types of plaster. To this end, painted, unpainted and pigmented specimens were tested. Experimental values were collected on diffusion and vapour permeability, or its inverse, water vapour resistivity.The data obtained were very useful for evaluating moisture exchange between plaster and the surrounding air, both during initial drying and throughout the life of the material. They likewise served as a basis for ensuring the proper evacuation of water vapour in walls, and use of the capacity of the porous network in plaster products to regulate moisture content or serve as a water vapour barrier to avoid condensation.Briefly, the research showed that pigments, water-based paints and silicon-based water repellents scantly raised vapour resistance. Plastic paints, enamels and lacquers, however, respectively induced five-, ten- and twenty-fold increases in vapour resistivity, on average.Se estudia el fenómeno de la resistividad al vapor de los de yeso y el efecto impermeabilizante que producen los recubrimientos de pintura sobre diversos tipos de yeso y escayola. Para ello, se ensayan probetas desnudas y recubiertas con distintos tipos de pintura, así como coloreados en masa. Se obtienen valores experimentales de la difusividad o permeabilidad al vapor o su inverso la resistividad al vapor de agua.Los datos obtenidos son muy útiles para valorar el fenómeno del intercambio de humedad entre el yeso y el ambiente, tanto durante el proceso de su secado inicial, como en el transcurso de su vida. Así como para disponer soluciones adecuadas para la evacuación del vapor de agua a través de los cerramientos, para utilizar la capacidad de regulación de la humedad, que proporciona el entramado poroso de los productos de yeso, o para impedir el paso del vapor de agua y evitar condensaciones.Como resumen de la investigación, se

  7. PPF-reinforced, ESP-lightened gypsum plaster

    Directory of Open Access Journals (Sweden)

    García Santos, A.

    2009-03-01

    Full Text Available A new construction material has been obtained by adding aggregate to gypsum plaster which, without reducing the bending strength of plain gypsum plaster without aggregates, lowers its density, and consequently the weight of the construction elements made from the agglomerated material, by half.The aggregates used were expanded polystyrene beads and short polypropylene fibre.The new material addresses one of the issues of cardinal interest in construction materials and construction element research, namely the need to lighten materials so as to ease the burden on buildings’ bearing structures while facilitating assembly of construction units, by a single worker wherever possible.With a water / binder ratio of 0.7 and 2% (by weight of plaster of expanded polystyrene and 2% of polypropylene fibre aggregates, the decline in density achieved was 50,88% over plain gypsum plaster and 32.88% over plasterboard.Se ha obtenido un nuevo material de construcción aditivando el yeso o la escayola, mediante la incorporación de agregados, de modo que sin reducir la resistencia a flexotracción de una escayola sin ningún tipo de adición, reduce su densidad a la mitad, y por tanto, el peso de los elementos constructivos que puedan realizarse basándose en él.El material está compuesto por una adición de gránulos de poliestireno expandido y fibras cortadas de polipropileno.El nuevo material incide sobre aquellos aspectos de más interés en el campo de la investigación en construcción, en donde se intenta reducir el peso de los materiales, de modo que se grave lo menos posible la estructura resistente de las edificaciones, a la par que se facilitan los procedimientos de montaje de las unidades constructivas, al poder ser manejadas por un solo operario.La escayola, con relación de agua/conglomerante de 0,7, y con adiciones del 2% en peso (sobre la cantidad de escayola, tanto de poliestireno expandido como de fibras de polipropileno, permite reducir la

  8. Development of Biodegradable Nanosheets as Nano-adhesive Plasters

    Institute of Scientific and Technical Information of China (English)

    Shinji; Takeoka; Yosuke; Okamura; Toshinori; Fujie; Yoshihito; Fukui

    2007-01-01

    1 Results A nano-adhesive plaster is a biodegradable polymeric sheet with nanometer thickness; e.g.,one side is adhesive to a wound and the other side has high surface compatibility as biomaterial application.We proposed three kinds of polymeric nanosheets; the first is a sheet with ca.5 nm thickness made by cross-linking of human serum albumin (HSA) absorbed on a patterned octadecyltrimethoxysilane monolayer,the second is a nanosheet with ca.100 nm thickness prepared by thermal fusion of biodegradable P...

  9. Primers role in plastering systems on concrete surfaces

    Science.gov (United States)

    Fischer, H. B.

    2015-01-01

    A drastic reduction in time frames between the manufacturing process of concrete units and the rendering phase (including prior priming) does not allow the concrete to dry well. This fact is also underlined by changes in concrete technology (denser concrete and denser concrete surfaces). The tests showed that the reduction of drying time (storage time) had a significant influence on the bonding properties of gypsum plaster on concrete surfaces. In such cases it is absolutely necessary to use an appropriate primer no matter what the processing temperature (2 °C to 20 °C) might be. In this publication the varying primer quality is shown.

  10. The performance of a restoration plaster in the field: Investigation and monitoring of two case studies

    NARCIS (Netherlands)

    Lubelli, B.; Hees, R.P.J. van; Groot, C.J.W.P.

    2005-01-01

    A large number of restoration plasters, especially developed for salt loaded substrates, have been introduced on the market in the last decades. The performance of these plasters in the field is not always satisfactory. The reasons of the failures may be found in the severity of the exposure conditi

  11. Salt transport and crystallization in plaster layers: A nuclear magnetic resonance study

    NARCIS (Netherlands)

    Petkovic, J.; Pel, L.; Huinink, H.P.; Kopinga, K.; Hees, R.P.J. van

    2005-01-01

    The durability and performance of specially developed restoration plasters or renders, are not always as good as expected. Salt crystallization is one of the causes of the observed degradation processes. To understand these processes in more detail, we investigated whether transport in the plasters

  12. 3-D Wizardry: Design in Papier-Mache, Plaster, and Foam.

    Science.gov (United States)

    Wolfe, George

    Papier-mache, plaster, and foam are inexpensive and versatile media for 3-dimensional classroom and studio art experiences. They can be used equally well by elementary, high school, or college students. Each medium has its own characteristic. Papier-mache is pliable but dries into a hard, firm surface that can be waterproofed. Plaster can be…

  13. The performance of a restoration plaster in the field: Investigation and monitoring of two case studies

    NARCIS (Netherlands)

    Lubelli, B.; Hees, R.P.J. van; Groot, C.J.W.P.

    2005-01-01

    A large number of restoration plasters, especially developed for salt loaded substrates, have been introduced on the market in the last decades. The performance of these plasters in the field is not always satisfactory. The reasons of the failures may be found in the severity of the exposure conditi

  14. 3-D Wizardry: Design in Papier-Mache, Plaster, and Foam.

    Science.gov (United States)

    Wolfe, George

    Papier-mache, plaster, and foam are inexpensive and versatile media for 3-dimensional classroom and studio art experiences. They can be used equally well by elementary, high school, or college students. Each medium has its own characteristic. Papier-mache is pliable but dries into a hard, firm surface that can be waterproofed. Plaster can be…

  15. Comparison of linear measurements and analyses taken from plaster models and three-dimensional images.

    Science.gov (United States)

    Porto, Betina Grehs; Porto, Thiago Soares; Silva, Monica Barros; Grehs, Renésio Armindo; Pinto, Ary dos Santos; Bhandi, Shilpa H; Tonetto, Mateus Rodrigues; Bandéca, Matheus Coelho; dos Santos-Pinto, Lourdes Aparecida Martins

    2014-11-01

    Digital models are an alternative for carrying out analyses and devising treatment plans in orthodontics. The objective of this study was to evaluate the accuracy and the reproducibility of measurements of tooth sizes, interdental distances and analyses of occlusion using plaster models and their digital images. Thirty pairs of plaster models were chosen at random, and the digital images of each plaster model were obtained using a laser scanner (3Shape R-700, 3Shape A/S). With the plaster models, the measurements were taken using a caliper (Mitutoyo Digimatic(®), Mitutoyo (UK) Ltd) and the MicroScribe (MS) 3DX (Immersion, San Jose, Calif). For the digital images, the measurement tools used were those from the O3d software (Widialabs, Brazil). The data obtained were compared statistically using the Dahlberg formula, analysis of variance and the Tukey test (p plaster models using the caliper and from the digital models using O3d software were identical.

  16. Impact of grain storage into silo bags on soil penetration resistance

    Science.gov (United States)

    Hernández, Juan Pablo; Alé, Daniel; Sabattini, Rafael; Díaz, Eduardo; Lado, Marcos; González, Antonio Paz

    2015-04-01

    Big silo sacks or bags ("silo bolsas", in Spanish) are nowadays widely used in Argentina as an innovative technology for grain storage and conservation on the farm. Following the last harvest campaigns, 40.000.000 Toms of grains were stored in silo sacks. A standard silo sack, or silo bag, has a length of about 75 m and is 2.7 m in diameter; when laden with cereal grains, a pressure of 9.8 MPa is applied on the soil surface. Silo sacks are currently installed within agricultural fields, and, after the storage period has finished, the plot they occupied most commonly again is cultivated. The aim of this study was to assess the effect of silo sacks on soil penetration resistance (PR). Two field experiments were performed in sites located at the departments of Paraná and Nogoyá, Entre Ríos province, Argentina. The soils in both sites were classified as Vertisols and contained expansible smectite minerals, mainly montmorillonite. Soil PR was continuously recorded until 80 cm depth. The first experiment, conducted in Paraná department, involved three different treatments with five RP replicated measurements per treatment: a) a plot under a silo bag with regular machinery transit for grain uploading and downloading, and previously used as pasture for livestock, b) a plot under grassland used for mowing and without livestock transit, and c) a plot under woody native vegetation, locally called "Espinal". The second experiment, conducted at Nogoyá department consisted of two treatments, each with for PR replications: a) a plot under silo sack with machinery transit, and b) a control plot located in the neighbouring field. n the first site a significant increase in soil PR (Psilo bag was recorded at the 0-20cm depth. In the second site soil PR was not significantly different between treatments at the 0-5 cm depth, while significant differences in PR were recorded at the 5-10 cm depth (Psilo bag provide information to assess the presence of compacted areas after the end

  17. Systemic model for the aid for operating of the reactor Siloe; Modelisation systeme pour l`aide a l`exploitation du reacteur de recherche Siloe

    Energy Technology Data Exchange (ETDEWEB)

    Royer, J.C.; Moulin, V.; Monge, F. [CEA Centre d`Etudes de Grenoble, 38 (France). Direction des Reacteurs Nucleaires; Baradel, C. [ITMI APTOR, 38 - Meylan (France)

    1995-12-31

    The Service of the Reactor Siloe (CEA/DRN/DRE/SRS), fully aware of the abilities and knowledge of his teams in the field of research reactor operating, has undertaken a project of knowledge engineering in this domain. The following aims have been defined: knowledge capitalization for the installation in order to insure its perenniality and valorization, elaboration of a project for the aid of the reactor operators. This article deals with the different actions by the SRS to reach the aims: realization of a technical model for the operation of the Siloe reactor, development of a knowledge-based system for the aid for operating. These actions based on a knowledge engineering methodology, SAGACE, and using industrial tools will lead to an amelioration of the security and the operating of the Siloe reactor. (authors). 13 refs., 7 figs.

  18. Lateral Pressure of RC Silos with Static and Dynamic Granular Materials

    Institute of Scientific and Technical Information of China (English)

    Lingkai Meng

    2015-01-01

    This paper aims at analyzing material⁃induced lateral pressure of RC cylinder silo in both static and dynamic condition using the finite element method (FEM).In the finite element software ABAQUS, concrete material is modeled by concrete damaged plasticity model, and stored materials in silo is modeled by the hypoplastic theory.In terms of numerical model, shell elements (S4R) and solid elements (C3D8) are applied for model silo wall and stored materials respectively. The interaction between silo wall and stored materials is simulated by Coulomb friction model and penalty contact constrain provided by ABAQUS.The numerical results are verified with the existing experimental data that are designed to ensure the validation of such numerical model using FEM and it obtains good agreements between numerical results and experimental data. Then the material parameters are analyzed in both static and dynamic condition.According to the analysis, it is clear that critical friction angle, initial void ratio and minimum void ratio have an obvious effect on static lateral pressure while all the material parameters affect dynamic lateral pressure at different levels. In addition, differences of silo wall between elastic and plastic state are analyzed in dynamic condition. The numerical results show that it contributes to increasing dynamic pressure when silo wall enters into the plastic state. Finally, this paper discusses the time⁃history lateral pressure at different heights along silo wall, and analytical results indicate that larger acceleration values play main roles in producing the maximum lateral pressure at higher part of the silo wall.

  19. The impact of silo mentality on team identity: An organisational case study

    Directory of Open Access Journals (Sweden)

    Frans Cilliers

    2012-01-01

    Full Text Available Orientation: Organisational silos do not only refer to conscious structures, but also to an unconscious state of mind and mentality that takes on a life of its own. Silos result in the splitting of organisational artefacts and relationships, and impact negatively on relationship forming between individuals and within teams.Research purpose: The purpose of this research was to describe how the silo mentality impacts on team identity.Motivation for the study: During a recent organisational consultation the researchers realised that a so-called silo phenomenon had much more unexplained unconscious behaviour than was traditionally realised in terms of organisational development. It is hoped that findings from this qualitative study could give consultants entry into what happens below the surface in the silos’ unconscious.Research design, approach and method: A qualitative and descriptive research design using a case study strategy was used. Data gathering consisted of 25 narrative interviews. Using discourse analysis four themes manifested, integrated into four working hypotheses and a research hypothesis. Trustworthiness and ethical standards were ensured.Main findings: Themes that emerged were the physical environment and structure, intra-group relations, experiences of management, and intergroup relations.Practical/managerial implications: Consulting on silo behaviour as physical structures only may not be successful in changing organisational behaviour. The silo resembles an iceberg – the largest part is below the surface.Contribution/value-add: The findings evidenced silo behaviour to be an unconscious phenomenon influencing team identity negatively. Consultants are urged to study these manifestations towards understanding silos and their effect on team identity better.

  20. Theoretical preconditions for optimization of composition and technological parameters of the plaster for walls made of aerated concrete blocks (rus

    Directory of Open Access Journals (Sweden)

    Paruta V.A.

    2012-12-01

    Full Text Available The paper reveals the mechanism of cracking in the "aerated concrete masonry - plaster coating" system, which causes the reduction of cladding’s durability. The temperature deformations in the structure are analyzed. On this basis the theoretical background to optimize the composition and technological parameters of the plaster was developed. The composition of plaster mixtures based on the expanded clay, carbonate, perlite and other fillers was also developed. The proposition that targeted modification of plaster can ensure optimal operation of the "laying-plaster" system is experimentally confirmed.

  1. Thermophysical properties of hydrophobised lime plaster - Experimental analysis of moisture effect

    Science.gov (United States)

    Pavlíková, Milena; Pernicová, Radka; Pavlík, Zbyšek

    2016-07-01

    Lime plasters are the most popular finishing materials in renewal of historical buildings and culture monuments. Because of their limited durability, new materials and design solutions are investigated in order to improve plasters performance in harmful environmental conditions. For the practical use, the plasters mechanical resistivity and the compatibility with substrate are the most decisive material parameters. However, also plasters hygric and thermal parameters affecting the overall hygrothermal function of the renovated structures are of the particular importance. On this account, the effect of moisture content on the thermophysical properties of a newly designed lime plasters containing hydrophobic admixture is analysed in the paper. For the comparative purposes, the reference lime and cement-lime plasters are tested as well. Basic characterization of the tested materials is done using bulk density, matrix density, and porosity measurements. Thermal conductivity and volumetric heat capacity in the broad range of moisture content are experimentally accessed using a transient impulse method. The obtained data reveals the significant increase of the both studied thermal parameters with increasing moisture content and gives information on plasters behaviour in a highly humid environment and/or in the case of their possible direct contact with liquid water. The accessed material parameters will be stored in a material database, where can find use as an input data for computational modelling of coupled heat and moisture transport in this type of porous building materials.

  2. The topical 5% lidocaine medicated plaster in localized neuropathic pain: a reappraisal of the clinical evidence.

    Science.gov (United States)

    de León-Casasola, Oscar A; Mayoral, Victor

    2016-01-01

    Topical 5% lidocaine medicated plasters represent a well-established first-line option for the treatment of peripheral localized neuropathic pain (LNP). This review provides an updated overview of the clinical evidence (randomized, controlled, and open-label clinical studies, real-life daily clinical practice, and case series). The 5% lidocaine medicated plaster effectively provides pain relief in postherpetic neuralgia, and data from a large open-label controlled study indicate that the 5% lidocaine medicated plaster is as effective as systemic pregabalin in postherpetic neuralgia and painful diabetic polyneuropathy but with an improved tolerability profile. Additionally, improved analgesia and fewer side effects were experienced by patients treated synchronously with the 5% lidocaine medicated plaster, further demonstrating the value of multimodal analgesia in LNP. The 5% lidocaine medicated plaster provides continued benefit after long-term (≤7 years) use and is also effective in various other LNP conditions. Minor application-site reactions are the most common adverse events associated with the 5% lidocaine medicated plaster; there is minimal risk of systemic adverse events and drug-drug interactions. Although further well-controlled studies are warranted, the 5% lidocaine medicated plaster is efficacious and safe in LNP and may have particular clinical benefit in elderly and/or medically compromised patients because of the low incidence of adverse events.

  3. Evaluation of linear dimensional stability of various combinations of dental stone and plaster.

    Science.gov (United States)

    Adegbulugbe, I C; Oderinu, O H; Shaba, O P; Oremosu, O A

    2011-01-01

    It has been observed that due to the cheaper cost of dental plaster compared to dental stone, casts on which most of the dental prostheses and appliances were being fabricated in various laboratories were often mixtures of dental stone and dental plaster in order to reduce production cost. To evaluate the dimensional stability of various combinations of Dental Stone and Dental Plaster mixtures used to make dental casts. Alginate impressions of a master model of truncated metal cones were made and casts were produced by pouring with various combinations of dental stone and dental plaster mixtures. The linear dimensional differences between the inter-abutment distances on the casts were measured with an electronic caliper. One sample t-test and percentage differences were calculated. Dimensional variations for the distances measured using either 50% dental stone or 25% dental stone with plaster were statistically significant (p d" 0.05). Mixture of 75% dental stone and 25% dental plaster produced casts with no statistically significant dimensional variation from the master model (p e" 0.05). A mixture of 75% dental stone and 25% dental plaster could be used for procedures not requiring very accurate replica like mounting of teeth for dental training and for study models.

  4. Venous thromboembolism during hip plaster cast immobilisation: review of the literature.

    Science.gov (United States)

    Struijk-Mulder, M C; Ettema, H B; Heyne, R A J; Rondhuis, J J; Büller, H R; Verheyen, C C P M

    2014-01-01

    There is a paucity of data regarding the risk of deep vein thrombosis during hip plaster cast immobilisation. The purpose of this article was to review the available evidence regarding the incidence of symptomatic venous thromboembolism (VTE) during hip plaster cast immobilisation. All papers describing hip plaster cast immobilisation published in the English literature retrieved from PubMed, EMBASE and the Cochrane database were reviewed. Articles regarding children, hip dysplasia, congenital hip dislocation and Legg-Calvé-Perthes were excluded. A total of three papers were available for analysis. We also describe a case of pulmonary embolism during hip cast immobilisation. The overall incidence of symptomatic VTE during hip plaster cast immobilisation was 0% in 343 patients. The incidence of symptomatic VTE in hip cast brace was 2.3% (range 0-3%). Our systematic review of the literature showed a paucity of data regarding the incidence of VTE during hip plaster cast immobilisation. We describe the first case of pulmonary embolism during hip plaster cast immobilisation. We recommend that patients who are fitted with a hip plaster cast should be routinely screened for additional risk factors. When risk factors are present, patients should be considered for pharmacological thromboprophylaxis.

  5. [Acupuncture combined with moxibustion plaster for nerve-root type cervical spondylosis].

    Science.gov (United States)

    Liu, Li-an; Zhang, Shu; Wang, Hajying; Tang Lixin

    2016-02-01

    To compare the clinical efficacy differences between acupuncture combined with moxi-bustion plaster and electroacupuncture (EA) for nerve-root type cervical spondylosis. A total of 60 casesof nerve-root type cervical spondylosis were randomly divided into a plaster group and an EA group, 30 cases ineach one. Patients in the plaster group were treated with regular acupuncture at Jiaji(EX-B 2) points and ashipoints, combined with moxibustion plaster at Gaohuang (BL 43); patients in the EA group were treated with EAat identical acupoints as plaster group. The treatment was given once a day, and 5 days were taken as one course;there was an interval of 2 days between courses and totally 2 courses were performed. The pain questionnaires andquantitative score of signs and symptoms were observed before and after treatment in the two groups. The clinicalefficacy of the two groups was compared. The total effective rate was 96. 7% (29/30) in the plastergroup, which was not significantly different from 93. 3% (28/30) in the EA group (P>0. 05). After treatment,PRI, VAS and PPI were all reduced in the two groups (all Pplaster groups (all Pplaster group (all Pplaster and EA both have superior clinical efficacy for nerve-root type cervical spondylosis; EA issuperior to acupuncture combined with moxibustion plaster on relieving pain, while acupuncture combined withmoxibustion plaster is superior to EA on improving life quality, muscle strength and feeling.

  6. Orthodontic measurements on digital study models compared with plaster models: a systematic review.

    Science.gov (United States)

    Fleming, P S; Marinho, V; Johal, A

    2011-02-01

    The aim of this study is to evaluate the validity of the use of digital models to assess tooth size, arch length, irregularity index, arch width and crowding versus measurements generated on hand-held plaster models with digital callipers in patients with and without malocclusion. Studies comparing linear and angular measurements obtained on digital and standard plaster models were identified by searching multiple databases including MEDLINE, LILACS, BBO, ClinicalTrials.gov, the National Research Register and Pro-Quest Dissertation Abstracts and Thesis database, without restrictions relating to publication status or language of publication. Two authors were involved in study selection, quality assessment and the extraction of data. Items from the Quality Assessment of Studies of Diagnostic Accuracy included in Systematic Reviews checklist were used to assess the methodological quality of included studies. No meta-analysis was conducted. Comparisons between measurements of digital and plaster models made directly within studies were reported, and the difference between the (repeated) measurement means for digital and plaster models were considered as estimates. Seventeen relevant studies were included. Where reported, overall, the absolute mean differences between direct and indirect measurements on plaster and digital models were minor and clinically insignificant. Orthodontic measurements with digital models were comparable to those derived from plaster models. The use of digital models as an alternative to conventional measurement on plaster models may be recommended, although the evidence identified in this review is of variable quality. © 2010 John Wiley & Sons A/S.

  7. Accuracy of laser-scanned models compared to plaster models and cone-beam computed tomography.

    Science.gov (United States)

    Kim, Jooseong; Heo, Giseon; Lagravère, Manuel O

    2014-05-01

    To compare the accuracy of measurements obtained from the three-dimensional (3D) laser scans to those taken from the cone-beam computed tomography (CBCT) scans and those obtained from plaster models. Eighteen different measurements, encompassing mesiodistal width of teeth and both maxillary and mandibular arch length and width, were selected using various landmarks. CBCT scans and plaster models were prepared from 60 patients. Plaster models were scanned using the Ortho Insight 3D laser scanner, and the selected landmarks were measured using its software. CBCT scans were imported and analyzed using the Avizo software, and the 26 landmarks corresponding to the selected measurements were located and recorded. The plaster models were also measured using a digital caliper. Descriptive statistics and intraclass correlation coefficient (ICC) were used to analyze the data. The ICC result showed that the values obtained by the three different methods were highly correlated in all measurements, all having correlations>0.808. When checking the differences between values and methods, the largest mean difference found was 0.59 mm±0.38 mm. In conclusion, plaster models, CBCT models, and laser-scanned models are three different diagnostic records, each with its own advantages and disadvantages. The present results showed that the laser-scanned models are highly accurate to plaster models and CBCT scans. This gives general clinicians an alternative to take into consideration the advantages of laser-scanned models over plaster models and CBCT reconstructions.

  8. Influence of Conditions of Preparing the Foamed Plaster on its Degree of Foaming

    Directory of Open Access Journals (Sweden)

    M. Pawlak

    2007-07-01

    Full Text Available Foamed plaster moulds are used in precision casting process of non-ferrous alloys. Casting from those moulds are characterizedby high dimensional accuracy, very good shape pattering and small surface roughness. However, a drawback of the plaster mould is very low permeability. A substational improvement of this parametr may be achived through physical or phisico-chemical treatment of the plaster slurry or prepared mould. The most advantageous results can be obtained by foaming the slurry. The investigatious comprised evaluation of the influence of mixing parametrs (mixer type, rotation and mixing time, settings the mixer in mixing device and the content of a foaming agent on the degree of foaming of the plaster. The tests were carried out using the α-plaster Hartform-H1 and Alkanol XC as a foaming agent. The structure of a slurry produced after foaming is non-homogeous. Therefore, the investigations were completed by making appropriate of this process. Analysis of the results leads to the conclusion, that the foamed plaster Hartform_H1 reaches the top degree of foaming at the following parameters: the water/plaster ratio W/G=0.55, the content of Alkanol XC a=0.07%, stirring with a perforate disc mixer at the rotation speed nm=4000 rpm during τm=30 s. In turn the top homogeneity of the foamed plaster slurry can be achieved at the rotation speed nu=1400 rpm during τu=30 s., while other parameters are the same as in the foaming process. The obtained results can provide the basis for the elaboration of the industry procedures useful in the production of the plaster moulds for precision casting.

  9. Características da fermentação da silagem obtida em diferentes tipos de silos sob efeito do tamanho de partícula e da altura de colheita das plantas de milho Characteristics fermentative obtained of the different silos type silage a effect of particle size and cutting height of corn plant

    Directory of Open Access Journals (Sweden)

    Mikael Neumann

    2007-06-01

    Full Text Available O experimento foi conduzido no Núcleo de Produção Animal da Universidade Estadual do Centro Oeste do Paraná (UNICENTRO e teve como objetivo avaliar a qualidade das silagens obtidas e o nível de perdas de matéria seca (MS, de proteína bruta (PB e de fibra em detergente neutro (FDN ocorridas durante o processo fermentativo em dois tipos de silo (experimental de PVC e semitrincheira, bem como avaliar a eficiência de compactação (densidade do material ensilado. A forrageira utilizada foi a planta inteira de milho, que foi triturada em dois tamanhos de partícula (pequena: entre 0,2 e 0,6cm, ou grande: entre 1,0 e 2,0cm e cortada a duas alturas da superfície (baixo: 15cm, ou alto: 39cm, utilizando-se de três repetições (tipo de silo para cada silagem, compondo-se oito tratamentos num esquema fatorial 2 x 2 x 2. Os teores de MS e PB das silagens não foram afetados (P>0,05 pelo tamanho de partícula, pela altura de colheita e pelo tipo de silo utilizado. Por outro lado, as silagens produzidas nos dois tipos de silo diferiram quanto aos teores de matéria orgânica, FDN e N amoniacal em relação ao teor de N total, como também diferiram quanto ao grau de acidez (pH, densidade e perdas de PB e FDN. A densidade também foi afetada (PThe experiment was conducted at the Núcleo de Produção Animal of the Universidade Estadual do Centro Oeste do Paraná (UNICENTRO. It was aimed at evaluating the silage obtained quality and dry matter (DM, crude protein (CP and neutral detergent fiber (NDF losses occurred during fermentative process on two silos type (PVC type and commercial type as well as evaluate the compact efficiency of silage. The forage used was corn plant harvested of the different particle sizes (small: between 0.2 and 0.6cm or large: between 1.0 and 2.0cm and cutting heights (low cut: 15cm or high cut: 39cm, using three replication (silos type for every silage, contained eight treatments in factorial scheme 2 x 2 x 2. The values of

  10. OBSERVATION ON THE THERAPEUTIC EFFECT OF AURICULAR PLASTER FOR TREATMENT OF 135 CASES OF MOTION SICKNESS

    Institute of Scientific and Technical Information of China (English)

    RAO Zhongdong; WEN Ming; HU Yuehua

    2002-01-01

    In the present paper, the therapeutic effects of auricular plaster (otopoint-pellet pressing therapy)and Western medicine (Dramamine) were compared in the treatment of 200 cases of motion sickness who were randomly divided into auricular plaster group (n = 135) and Western medicine (control) group (n = 65). Results indicated that the markedly effective rates and total effective rates of auricular plaster group and control group were 51. 1% and 23. 1 %, 94.1% and 81.6% respectively, and the therapeutic effect of the former group was significantly superior to that of the control group (P<0.01).

  11. Influence of the input parameters on the efficiency of plaster sanding with alundum abrasive discs

    Science.gov (United States)

    Krajcarz, D.; Spadło, S.; Młynarczyk, P.

    2017-02-01

    The paper presents test results concerning the relationship between selected input parameters and the process efficiency for the sanding of plaster surfaces with alundum abrasive discs. The input parameters under study were the size of the abrasive grains, the force exerted by the plaster sample pressing against the abrasive disc and the no-load rotational speed of the abrasive disc. The experimental data illustrating the relationship between the process efficiency and the particular input parameters were used to select the optimum plaster sanding conditions.

  12. 浅谈钢板仓的安全管理%Introduction to safety management of the steel silo

    Institute of Scientific and Technical Information of China (English)

    李辉如

    2015-01-01

    介绍了钢板仓的类型,根据钢板仓的使用经验,分析了影响钢板仓安全使用的因素,对钢板的安全使用及安全管理措施进行了探讨.%this paper introduces the types of steel silo, according to the experience of the use of steel silo, analyses the factors affecting the safe use of steel silo, safe use and safety management measures of steel silo are discussed in this paper.

  13. New Plaster Composite with Mineral Wool Fibres from CDW Recycling

    Directory of Open Access Journals (Sweden)

    Sonia Romaniega Piñeiro

    2015-01-01

    Full Text Available Over the last decade the intense activity of the building sector has generated large quantities of construction and demolition waste (CDW. In particular, in Europe around 890 million tons of CDW is generated every year; however, only 50% of them are recycled. In Spain, over the last years 40 millions of tons of construction and demolition waste have been generated. On the other hand, since the implementation of the Technical Building Code regulation the use of mineral wools as building insulation materials has become a widespread solution in both rehabilitation and new construction works, and because of that, this kind of insulation waste is increasing. This research analyzes the potential of a new composite (gypsum and fiber waste including several mineral wools waste into a plaster matrix. For this purpose, an experimental plan, characterizing the physical and mechanical behaviour as well as the Shore C hardness of the new composite, was elaborated fulfilling UNE Standards.

  14. Health information exchange, system size and information silos.

    Science.gov (United States)

    Miller, Amalia R; Tucker, Catherine

    2014-01-01

    There are many technology platforms that bring benefits only when users share data. In healthcare, this is a key policy issue, because of the potential cost savings and quality improvements from 'big data' in the form of sharing electronic patient data across medical providers. Indeed, one criterion used for federal subsidies for healthcare information technology is whether the software has the capability to share data. We find empirically that larger hospital systems are more likely to exchange electronic patient information internally, but are less likely to exchange patient information externally with other hospitals. This pattern is driven by instances where there may be a commercial cost to sharing data with other hospitals. Our results suggest that the common strategy of using 'marquee' large users to kick-start a platform technology has an important drawback of potentially creating information silos. This suggests that federal subsidies for health data technologies based on 'meaningful use' criteria, that are based simply on the capability to share data rather than actual sharing of data, may be misplaced.

  15. Creating value: unifying silos into public health business intelligence.

    Science.gov (United States)

    Davidson, Arthur J

    2014-01-01

    Through September 2014, federal investments in health information technology have been unprecedented, with more than 25 billion dollars in incentive funds distributed to eligible hospitals and providers. Over 85 percent of eligible United States hospitals and 60 percent of eligible providers have used certified electronic health record (EHR) technology and received Meaningful Use incentive funds (HITECH Act1). Certified EHR technology could create new public health (PH) value through novel and rapidly evolving data-use opportunities, never before experienced by PH. The long-standing "silo" approach to funding has fragmented PH programs and departments,2 but the components for integrated business intelligence (i.e., tools and applications to help users make informed decisions) and maximally reuse data are available now. Challenges faced by PH agencies on the road to integration are plentiful, but an emphasis on PH systems and services research (PHSSR) may identify gaps and solutions for the PH community to address. Technology and system approaches to leverage this information explosion to support a transformed health care system and population health are proposed. By optimizing this information opportunity, PH can play a greater role in the learning health system.

  16. Characterization of a lime-pozzolan plaster containing phase change material

    Energy Technology Data Exchange (ETDEWEB)

    Pavlíková, Milena; Pavlík, Zbyšek; Trník, Anton; Pokorný, Jaroslav; Černý, Robert [Department of Materials Engineering and Chemistry, Faculty of Civil Engineering, Czech Technical University in Prague, Thákurova 7, 166 29 Prague (Czech Republic)

    2015-03-10

    A PCM (Phase Change Material) modified lime-pozzolan plaster for improvement of thermal energy storage of building envelopes is studied in the paper. The investigated plaster is composed of lime hydrate, pozzolan admixture based on metakaolin and mudstone, silica sand, water and paraffin wax encapsulated in polymer capsule. The reference plaster without PCM application is studied as well. The analyzed materials are characterized by bulk density, matrix density, total open porosity, compressive strength and pore size distribution. The temperature of phase change, heat of fusion and crystallization are studied using DSC (Difference Scanning Calorimetry) analysis performed in air atmosphere. In order to get information on materials hygrothermal performance, determination of thermal and hygric properties is done in laboratory conditions. Experimental data reveal a substantial improvement of heat storage capacity of PCM-modified plaster as compared to the reference material without PCM.

  17. Reliability and validity of measurements on digital study models and plaster models.

    Science.gov (United States)

    Reuschl, Ralph Philip; Heuer, Wieland; Stiesch, Meike; Wenzel, Daniela; Dittmer, Marc Philipp

    2016-02-01

    To compare manual plaster cast and digitized model analysis for accuracy and efficiency. Nineteen plaster models of orthodontic patients in permanent dentition were analyzed by two calibrated examiners. Analyses were performed with a diagnostic calliper and computer-assisted analysis after digitization of the plaster models. The reliability and efficiency of different examiners and methods were compared statistically using a mixed model. Statistically significant differences were found for comparisons of all 28 teeth (P plaster model analysis appears to be an adequate, reliable, and time saving alternative to analogue model analysis using a calliper. © The Author 2015. Published by Oxford University Press on behalf of the European Orthodontic Society. All rights reserved. For permissions, please email: journals.permissions@oup.com.

  18. Vertical Extraction Process Implemented at the 118-K-1 Burial Ground for Removal of Irradiated Reactor Debris from Silo Structures - 12431

    Energy Technology Data Exchange (ETDEWEB)

    Teachout, Douglas B. [Vista Engineering Technologies, LLC, Richland, Washington, 99352 (United States); Adamson, Clinton J.; Zacharias, Ames [Washington Closure Hanford, LLC, Richland, Washington, 99352 (United States)

    2012-07-01

    information supporting job planning and understanding of the conditions was the data obtained from the gross gamma meter that was inserted into each casing to provide a rough estimate of dose rates in the tubes. No added value was realized in attempting to quantify the source term and/or associate the isotopic activity with a particular actual waste form (e.g., sludge). Implementing the WRM system allowed monitoring of worker and boundary exposure rates from a distance, maintaining compliance with ALARA principles. This system also provided the project team early knowledge of items being removed that had high exposure rates associated with them, thus creating an efficient method of acknowledging an issue and arriving at a solution prior to having an upset condition. An electronic dosimeter with telemetry capability replaced the excavator mounted AMP-100 system approximately half way through remediation of the silos. Much higher connectivity efficiency was derived from this configuration. Increasing the data feed efficiency additionally led to less interruption of the remediation effort. Early in system testing process a process handicap on the excavator operator was acknowledged. A loss of depth perception resulted when maneuvering the excavator and bucket using the camera feed to an in-cab monitor. Considerable practice and mock-up testing allowed this handicap to be overcome. The most significant equipment failures involved the cable connection to the camera mounted between the clamshell bucket jaws and the video splitter in the excavator cab. Rotation of the clamshell bucket was identified as the cause of cable connection failures because of the cyclic twisting motion and continuous mechanical jarring of the connection. In-cab vibration was identified as the culprit in causing connection failures of the video splitter. While these failures were repaired, substantial production time was lost. Ultimately, the decision was made to purchase a second cable and higher quality

  19. Discharge flow of granular media from silos with a lateral orifice and injection of air

    Directory of Open Access Journals (Sweden)

    Aussillous Pascale

    2017-01-01

    Full Text Available Few studies concern the prediction of the mass flow rate of a granular media discharged from a silo with a lateral orifice. However, this situation can have pratical interest considering a tank of granular material with a leak on its side. We studied experimentally the discharge of a vertical silo filled by spherical glass beads. We consider rectangular silos with a rectangular orifice. The impact of size, aspect ratio and position of the orifice and the effect of an additional air flow were studied. The measured parameters are the mass flow rate and the pressure along the silo, whereas the controlled parameters are the size of particles, and the flow rate of air. We identified two regimes of discharge according to the aspect ratio (of width to height of the rectangular orifice. Increasing the air flow rate induces an increase of the granular media flow rate. Using a simple physical model to describe the grains and gas flow, we put in evidence the role played by the air pressure gradient at the outlet. Then we compared the experimental results with continuum Navier-Stokes simulations with the granular μ(I-rheology. We showed that the continuum μ(I-rheology describes well our discharge flow of granular media from silos, taking into account the effect of the position of the orifice as well as the coupling with the gas flow.

  20. Estimate of induced stress during filling and discharge of metallic silos for cement storage

    Directory of Open Access Journals (Sweden)

    Wilmer Bayona-Carvajal

    2015-01-01

    Full Text Available El presente artículo describe el análisis estructural realizado a un silo metálico que almacena cemento por medio de un modelo paramétrico desarrollado en el software de elementos finitos ANSYS APDL, las presiones de llenado y vaciado que el material ejerce sobre las paredes del silo se determinan basados en la normativa del Eurocódigo EN 1991-4. El modelo se realiza con elementos tipos cáscara permitiendo que su estructura se ajuste que la geometría cilíndrica y cónica del silo. Se explica cada una de las fases involucradas en el desarrollo del modelo y se hace un análisis detallado de los resultados arrojados por el software, se evalúan diferentes modelos variando los espesores de lámina con el fin de seleccionar el más adecuado. También se analizan los resultados obtenidos cuando la tolva del silo cambia su ángulo de inclinación y se revisa el comportamiento que tiene el silo cuando es analizado en conjunto con su estructura soporte.

  1. Topical pain management with the 5% lidocaine medicated plaster--a review.

    Science.gov (United States)

    Mick, Gérard; Correa-Illanes, Gerardo

    2012-06-01

    The topical 5% lidocaine medicated plaster is recommended as first-line treatment for localized peripheral neuropathic pain. In order to provide an overview of the efficacy and safety of the lidocaine plaster in the treatment of different neuropathic pain conditions, all efficacy and safety studies (randomized, controlled, or open-label with well described methodology), case reports, and pharmacological studies on the lidocaine plaster retrieved from a PubMed literature research (1960-March 2012) plus additional references identified from retrieved articles were included. The lidocaine plaster is efficacious in the treatment of neuropathic pain symptoms associated with previous herpes zoster infection. Results from a large open-label controlled study suggest that the lidocaine plaster could be at least as effective as systemic pregabalin in the treatment of postherpetic neuralgia and painful diabetic polyneuropathy. Open-label studies indicate efficacy in the treatment of other localized neuropathic pain conditions, such as painful idiopathic sensory polyneuropathy, complex regional pain syndrome, carpal tunnel syndrome sequelae, postsurgical and posttraumatic pain. Quality of life markedly improved in a variety of neuropathic pain conditions and long-term treatment provided sustained relief in patients with neuropathic pain who are responsive to lidocaine plaster. The lidocaine plaster is usually well tolerated. The risk of systemic adverse events and pharmacokinetic interactions with concomitant medication is minimal owing to low systemic exposure. Treatment of several, primarily neuropathic and mixed-pain conditions with the 5% lidocaine medicated plaster was found efficacious and safe. Further controlled studies, in particular where only small open-label studies or case reports are available, should be considered.

  2. Long-term treatment of neuropathic pain with a 5% lidocaine medicated plaster.

    Science.gov (United States)

    Wilhelm, Ilca Ricarda; Tzabazis, Alexander; Likar, Rudolf; Sittl, Reinhard; Griessinger, Norbert

    2010-02-01

    The 5% lidocaine medicated plaster is a topical treatment for peripheral neuropathic pain symptoms (e.g. burning, shooting and stabbing pain) and is registered for the treatment of postherpetic neuralgia. This study examined the efficacy and tolerability of long-term treatment with the 5% lidocaine medicated plaster in patients with localized neuropathic pain conditions. Twenty patients with localized neuropathic pain [postoperative neuropathic pain (n = 14); complex regional pain syndrome (n = 2); and postherpetic neuralgia (n = 4)], who had been successfully treated with 5% lidocaine medicated plaster, were followed up by telephone interview after 3 and 5 years. Questions were related to the efficacy, development of tolerance, tolerability, wear time and comfort of the plaster. At 3 years, 10 out of 20 (50%) initial responders were still using the plasters with no decline in analgesic efficacy. After 5 years, eight of the original 20 responders (40%) maintained treatment and continued to experience effective pain relief. The 12 responders who discontinued treatment did so because they no longer required analgesic therapy (n = 4); their health insurer refused to fund treatment (n = 2); they were lost to follow-up (n = 1); or had died from an illness unrelated to plaster treatment (n = 5). No patient discontinued because of inadequate analgesia or intolerable side effects. Reversible erythema occurred in two patients wearing the plaster for more than 16 h. There were no systemic side effects. The 5% lidocaine medicated plaster provides sustained pain relief over long-term treatment in patients with neuropathic pain of various causes and is well tolerated.

  3. Study and application of plasticity plaster-slurry for preventing coal spontaneous combustion

    Institute of Scientific and Technical Information of China (English)

    LIU Ai-hua(刘爱华); CAI Kang-xu(蔡康旭); GUO Da(郭达); ZHANG Fu-sheng(张复胜)

    2003-01-01

    Introduced the modulation scheme, function and mechanism of plasticity plaster-slurry preventing coal spontaneous combustion. The applications show that the plasticity plaster-slurry has good hygroscopicity and adsorptivity. To spray it on the coal wall of tunnel can shut off leakage wind fast and effectively. To press it into the coal body can absorb the heat and descend the temperature, surround the coal pieces, eliminate the possibility of the fiery district resuming combustion.

  4. The topical 5% lidocaine medicated plaster in localized neuropathic pain: a reappraisal of the clinical evidence

    Directory of Open Access Journals (Sweden)

    de León-Casasola OA

    2016-02-01

    Full Text Available Oscar A de León-Casasola,1,2 Victor Mayoral3 1Department of Anesthesiology, Division of Pain Medicine, Roswell Park Cancer Institute, 2University at Buffalo, School of Medicine and Biomedical Sciences. NY, USA; 3Anesthesiology Department, Pain Management Unit, University Hospital of Bellvitge, L'Hospitalet de Llobregat, Spain Abstract: Topical 5% lidocaine medicated plasters represent a well-established first-line option for the treatment of peripheral localized neuropathic pain (LNP. This review provides an updated overview of the clinical evidence (randomized, controlled, and open-label clinical studies, real-life daily clinical practice, and case series. The 5% lidocaine medicated plaster effectively provides pain relief in postherpetic neuralgia, and data from a large open-label controlled study indicate that the 5% lidocaine medicated plaster is as effective as systemic pregabalin in postherpetic neuralgia and painful diabetic polyneuropathy but with an improved tolerability profile. Additionally, improved analgesia and fewer side effects were experienced by patients treated synchronously with the 5% lidocaine medicated plaster, further demonstrating the value of multimodal analgesia in LNP. The 5% lidocaine medicated plaster provides continued benefit after long-term (≤7 years use and is also effective in various other LNP conditions. Minor application-site reactions are the most common adverse events associated with the 5% lidocaine medicated plaster; there is minimal risk of systemic adverse events and drug–drug interactions. Although further well-controlled studies are warranted, the 5% lidocaine medicated plaster is efficacious and safe in LNP and may have particular clinical benefit in elderly and/or medically compromised patients because of the low incidence of adverse events. Keywords: 5% lidocaine medicated plaster, clinical evidence, localized neuropathic pain, postherpetic neuralgia, review

  5. [Case-control study on close reduction and plaster slab fixation combined with plaster external traction for the treatment of pediatric Gartland type III supracondylar humerus fractures].

    Science.gov (United States)

    Kang, Yu-Xiang; Wei, Xiao-Chun; Li, Hai-Ming

    2014-07-01

    To compare the therapeutic effects between close reduction and plaster slab fixation combined with plaster external traction and operation for the treatment of pediatric closed Gartland type III supracondylar humerus fractures without neurovascular injury complications. From June 2009 to June 2012, 151 children with closed Gartland III supracondylar humerus fractures were retrospectively studied and divided into two groups, including 87 boys and 64 girls, ranging in age from 1 to 12 years old with an average of 5.3 years old. Among them, 76 children (conservative group) were treated with close reduction and plaster slab fixation combined with plaster external traction; 75 children (operation group) underwent surgical operation. The time of elbow joint function exercise, the healing time of fracture, the function recovery of elbow joint and carrying angle was recorded and analyzed. The therapeutic effects were evaluated by the Flynn criteria system. All patients were followed up from 6 to 36 months (18.3 months on average). The average time of fracture healing and elbow joint functional exercise of the conservative group was shorter than those of operation group (P 0.05). According to Flynn criteria system, in conservative group, the result was excellent in 31 cases, good in 35, fair in 7, and poor in 3; in operation group, 27 in excellent, 30 in good, 17 in fair and 1 in poor; there was no significant difference between two groups in therapeutic effects (P > 0.05). Close reduction and plaster slab fixation combined with plaster external traction in treatment of pediatric closed Gartland type III supracondylar humerus fractures without neurovascular injury complications,which has similar effect to surgical treatment, and the time of fracture healing and elbow joint function exercise are significantly shorter.

  6. Lethal Necrotizing Fasciitis Triggered by Plaster: Case Report and Review of Literature.

    Science.gov (United States)

    Jain, Mohit J; Mavani, Kinjal

    2016-01-01

    Plasters have been frequently associated with known complications such as infection, and compartment syndrome or deep vein thrombosis. However, life-threatening complication of necrotizing fasciitis (NF) has not been frequently attributed to plaster. We had a case of a 62-year male developing a lethal NF triggered by a below knee plaster for undisplaced fracture medial malleolus after twisting injury. He had no history suggestive of diabetes, renal impairment, and predisposing allergic factors or any comorbidity. Despite early diagnosis and aggressive management with above knee amputation, death occurs due to septic shock on the 20(th) day. A similar case of reported lethal NF triggered by plaster has also been reviewed in this report. This case highlights a life-threatening rare complication of plaster and author recommends thorough clinical history taking, precleaning of limb, use of sterile water and use of adequate wrap around skin for gypsum plasters as prevention apart from high index of suspicion for early diagnosis, and rapid management.

  7. Antiemetic efficacy of capsicum plaster on acupuncture points in patients undergoing thyroid operation.

    Science.gov (United States)

    Koo, Min Seok; Kim, Kyo Sang; Lee, Hee-Jong; Jeong, Ji Seon; Lee, Jung-Won

    2013-12-01

    Postoperative nausea and vomiting (PONV) occurs in up to 63-84% of patients after thyroid surgery. This study aims to assess the effects of using a capsicum plaster to reduce PONV after thyroid surgery at either the Chinese acupuncture point (acupoint) Pericardium 6 (P6) or Korean hand acupuncture point K-D2. One-hundred eighty-four patients who underwent thyroid surgery were randomized in four groups (n = 46 each): control group = inactive tape at P6 acupoints and on both shoulders as a nonacupoint; P6 group = capsicum plaster at P6 points and inactive tape on both shoulders; K-D2 group = capsicum plaster at K-D2 acupoints and inactive tape on both shoulders; Sham group = capsicum plaster on both shoulders and inactive tape at P6 acupoints. The capsicum plaster was applied before the induction of anesthesia and removed at 8 hr after surgery. The incidence and severity of nausea and vomiting and the need for rescue antiemetics were decreased in the patients in the P6 and K-D2 groups compared to the patients in the control and sham groups (P plaster at the P6 and K-D2 acupoint was a promising antiemetic method for the patients undergoing thyroid surgery.

  8. Outcomes of pin and plaster versus locking plate in distal radius intraarticular fractures.

    Science.gov (United States)

    Bahari-Kashani, Mahmoud; Taraz-Jamshidy, Mohammad Hosein; Rahimi, Hassan; Ashraf, Hami; Mirkazemy, Masoud; Fatehi, Amirreza; Asadian, Mariam; Rezazade, Jafar

    2013-01-01

    Distal radius fractures are among the most prevalent fractures predictive of probable occurrence of other osteoporotic fractures. They are treated via a variety of methods, but the best treatment has not been defined yet. This study was performed to compare the results of open reduction and internal fixation with locking plates versus the pin and plaster method. In this prospective study, 114 patients aged 40 to 60 years with Fernandez type III fracture referring to Imam-Reza and Mehr hospitals of Mashhad from 2009 to 2011, were selected randomly; after obtaining informed consent, they were treated with pin and plaster fixation (n = 57) or internal fixation with the volar locking plate (n = 57). They were compared at the one year follow up. Demographic features and standard radiographic indices were recorded and MAYO, DASH and SF - 36 tests were performed. Data was analyzed by SPSS software version 13, with descriptive indices, Mann-Whitney and Chi-square tests. SF-36 test demonstrated a better general health (P plaster group. Also, in the LCP group mean MAYO score (P plaster group. Mean DASH score was not different between the groups (P = 0.218). The rate of acceptable results of radiographic indices (P plaster method. In treatment of intra-articular distal radius fractures in middle-aged patients internal fixation with locking plates may be prefered to pin and plaster as the treatment of choice.

  9. Digital versus plaster study models: how accurate and reproducible are they?

    Science.gov (United States)

    Abizadeh, Neilufar; Moles, David R; O'Neill, Julian; Noar, Joseph H

    2012-09-01

    To compare measurements of occlusal relationships and arch dimensions taken from digital study models with those taken from plaster models. Laboratory study The Orthodontic Department, Kettering General Hospital, Kettering, UK Methods and materials: One hundred and twelve sets of study models with a range of malocclusions and various degrees of crowding were selected. Occlusal features were measured manually with digital callipers on the plaster models. The same measurements were performed on digital images of the study models. Each method was carried out twice in order to check for intra-operator variability. The repeatability and reproducibility of the methods was assessed. Statistically significant differences between the two methods were found. In 8 of the 16 occlusal features measured, the plaster measurements were more repeatable. However, those differences were not of sufficient magnitude to have clinical relevance. In addition there were statistically significant systematic differences for 12 of the 16 occlusal features, with the plaster measurements being greater for 11 of these, indicating the digital model scans were not a true 11 representation of the plaster models. The repeatability of digital models compared with plaster models is satisfactory for clinical applications, although this study demonstrated some systematic differences. Digital study models can therefore be considered for use as an adjunct to clinical assessment of the occlusion, but as yet may not supersede current methods for scientific purposes.

  10. Análise de pressões em silo vertical de alvenaria de tijolos Analysis of pressures in vertical silo of masonry of bricks

    Directory of Open Access Journals (Sweden)

    Marineide J. Diniz

    2006-03-01

    Full Text Available Objetiva-se com este trabalho, determinar as pressões verticais e horizontais nas paredes e no fundo de um silo cilíndrico, com altura/diâmetro igual a 1 e comparar as pressões teóricas obtidas através de normas internacionais. O silo foi construído em alvenaria de tijolos de 8 furos, fixando-lhe externamente nove cintas de aço. A metodologia e as técnicas aplicadas foram as indicadas pelas normas, com as devidas adaptações necessárias. Determinaram-se as propriedades de fluxo do produto na Máquina de Cisalhamento Direto Translacional (Jenike Shear Cell. Calcularam-se as pressões teóricas, de acordo com as recomendações das normas DIN 1055, ACI 313 e ISO 11697. O produto utilizado nos ensaios foi a areia, em razão da sua densidade ser aproximadamente duas vezes maior à maioria dos cereais. Para medição das pressões o silo foi instrumentado com 6 células de pressão, das quais 4 fixadas na parede e 2 no fundo do silo, além de conectadas a um sistema de aquisição de dados. Através da análise dos dados obtidos de forma experimental, juntamente com o conhecimento das propriedades do produto, conclui-se que o tipo de silo estudado apresenta potencial que permite a sua utilização para armazenamento de grãos nas propriedades rurais.The objective of this research was to determine the vertical and horizontal pressures on the walls and at the bottom of a cylindrical silo with height/diameter equal to 1 and to compare the obtained theoretical pressures through international rules. The silo was built in masonry of bricks, with 8 holes fixing externally nine steel braces. The applied methodology and techniques had been the ones as indicated by the rules with the necessary adaptations. The stream properties of the product were determined in the shearing machine translational direct Jenike Shear Cell. The theoretical pressures were calculated in agreement with the recommendations of the rules DIN 1055, ACI 313 and ISO 11697. The

  11. Composição bromatológica e perfil fermentativo da silagem de capim-elefante obtida em diferentes tipos de silos experimentais e no silo tipo trincheira Chemical composition and fermentation characteristics of elephantgrass silage obtained in different experimental and bunker silos

    Directory of Open Access Journals (Sweden)

    Paulo Henrique Mazza Rodrigues

    2002-11-01

    Full Text Available Três diferentes tipos de silos experimentais, confeccionados a partir de baldes plásticos, sacos plásticos e manilhas de concreto não impermeabilizadas, foram comparados com o silo comercial tipo trincheira, amostrado a 30 e 60 cm da sua superfície, para a ensilagem do capim-elefante (cv. Napier. Utilizaram-se, ainda, dois diferentes graus de compactação, correspondentes a 400 ou 600 kg de silagem/m³. O capim (33,0% de MS e 4,2% de PB foi homogeneizado e utilizado para encher quatro silos por tratamento, distribuídos em delineamento inteiramente casualizado. Depois de abertos, estes foram amostrados, para análise da composição bromatológica e do perfil fermentativo. Silagens produzidas em manilhas de concreto não impermeabilizadas apresentaram altos valores de pH, NIDA e lignina, baixas concentrações de ácido lático e nitrogênio amoniacal, baixo poder tampão e baixa digestibilidade in vitro. Silagens produzidas em silos experimentais apresentaram qualidade superior, quanto aos parâmetros amido, carboidratos solúveis, concentração de nitrogênio amoniacal, poder tampão, ácidos acético, propiônico, butírico e lático, do que aquelas produzidas no silo comercial. Silagens obtidas dos diferentes extratos do silo comercial apresentaram maior variabilidade para os parâmetros de fermentação do que aquelas obtidas entre diferentes tipos de silos experimentais.One type of commercial silo and three types of experimental silos were used for determination of chemical composition and fermentation characteristics of elephant grass (Pennisetum purpureum (33.0% DM and 4.2% CP ensiled in two different densities (400 or 600 kg of silage/m³: 1 commercial bunker silo sampled at 30 (top and 60 (deep cm from the top; 2 plastic silo with bulsen valve; 3 plastic bag; and 4 concrete pipe. A completely randomized design was used. The concrete pipe silo produced silage with higher pH, ADIN and lignin values, as well as lower in vitro

  12. Silos experimentais para avaliação da silagem de três genótipos de girassol (Helianthus annuus L. Evaluation of sunflower (Helianthus annuus L. silage of three genotypes as affected by experimental silos

    Directory of Open Access Journals (Sweden)

    L.G.R. Pereira

    2005-10-01

    Full Text Available Três tipos de silos experimentais foram utilizados para a avaliação das silagens de três genótipos de girassol: A silo padrão com válvula de Bunsen; B silo dotado de compartimento para efluentes e C silo com válvula de Bunsen e compartimento para efluentes. O delineamento experimental foi inteiramente ao acaso, em esquema fatorial 3×3 (genótipos × tipos de silos com três repetições. As características avaliadas foram: matéria seca (MS, densidade, proteína bruta (PB, nitrogênio amoniacal (N-NH3/N-T, pH, carboidratos solúveis (CHO, ácidos orgânicos, constituintes da parede celular, extrato etéreo (EE e digestibilidade in vitro da matéria seca (DIVMS. As silagens obtidas nos silos B e C apresentaram os maiores valores de MS e menores de NH3/N-T. Os valores de pH se equivaleram nos três tipos de silos, enquanto os teores de CHO foram menores para as silagens obtidas nos silos B e C. Os silos dotados de compartimento para efluentes apresentaram os maiores valores de ácido láctico. As frações fibrosas, EE e DIVMS não sofreram influência dos tipos de silos. A presença ou ausência da válvula de Bunsen não influenciou os parâmetros avaliados. A presença do compartimento para efluentes afetou a qualidade e o valor nutritivo da silagem de girassol.A completely randomized design in a 3×3 factorial scheme was used to evaluate the effect of three genotypes and three types of silos on sunflower silage. The silos were: A- silo with Bunsen valve; B- silo with effluent-collecting equipment; and C- silo with both Bunsen valve and effluent-collecting equipment. The parameters evaluated were: dry matter (DM, crude protein (CP, ammonia nitrogen (N-NH3/T-N, pH, soluble carbohydrates (CHO, organic acids, cell wall constituents, ether extract and in vitro dry matter digestibility (IVDMD. The silage from silos B and C had higher values of DM and lower levels of N-NH3/T-N. The pH value was the same for all silos, while the CHO was the

  13. Flow of granular matter in a silo with multiple exit orifices: Jamming to mixing

    Science.gov (United States)

    Kamath, Sandesh; Kunte, Amit; Doshi, Pankaj; Orpe, Ashish V.

    2014-12-01

    We investigate the mixing characteristics of dry granular material while draining down a silo with multiple exit orifices. The mixing in the silo, which otherwise consists of noninteracting stagnant and flowing regions, is observed to improve significantly when the flow through specific orifices is stopped intermittently. This momentary stoppage of flow through the orifice is either controlled manually or is chosen by the system itself when the orifice width is small enough to cause spontaneous jamming and unjamming. We observe that the overall mixing behavior shows a systematic dependence on the frequency of closing and opening of specific orifices. In particular, the silo configuration employing random jamming and unjamming of any of the orifices shows early evidence of chaotic mixing. When operated in a multipass mode, the system exhibits a practical and efficient way of mixing particles.

  14. Simulation study of the discharge characteristics of silos with cohesive particles

    Science.gov (United States)

    Hund, David; Weis, Dominik; Hesse, Robert; Antonyuk, Sergiy

    2017-06-01

    In many industrial applications the silo for bulk materials is an important part of an overall process. Silos are used for instance to buffer intermediate products to ensure a continuous supply for the next process step. This study deals with the discharging behaviour of silos containing cohesive bulk solids with particle sizes in the range of 100-500 μm. In this contribution the TOMAS [1,2] model developed for stationary and non-stationary discharging of a convergent hopper is verified with experiments and simulations using the Discrete Element Method. Moreover the influence of the cohesion of the bulk solids on the discharge behaviour is analysed by the simulation. The simulation results showed a qualitative agreement with the analytical model of TOMAS.

  15. Should the scope of human mixture risk assessment span legislative/regulatory silos for chemicals?

    Science.gov (United States)

    Evans, Richard M; Martin, Olwenn V; Faust, Michael; Kortenkamp, Andreas

    2016-02-01

    Current chemicals regulation operates almost exclusively on a chemical-by-chemical basis, however there is concern that this approach may not be sufficiently protective if two or more chemicals have the same toxic effect. Humans are indisputably exposed to more than one chemical at a time, for example to the multiple chemicals found in food, air and drinking water, and in household and consumer products, and in cosmetics. Assessment of cumulative risk to human health and/or the environment from multiple chemicals and routes can be done in a mixture risk assessment (MRA). Whilst there is a broad consensus on the basic science of mixture toxicology, the path to regulatory implementation of MRA within chemical risk assessment is less clear. In this discussion piece we pose an open question: should the scope of human MRA cross legislative remits or 'silos'? We define silos as, for instance, legislation that defines risk assessment practice for a subset of chemicals, usually on the basis of substance/product, media or process orientation. Currently any form of legal mandate for human MRA in the EU is limited to only a few pieces of legislation. We describe two lines of evidence, illustrated with selected examples, that are particularly pertinent to this question: 1) evidence that mixture effects have been shown for chemicals regulated in different silos and 2) evidence that humans are co-exposed to chemicals from different silos. We substantiate the position that, because there is no reason why chemicals allocated to specific regulatory silos would have non-overlapping risk profiles, then there is also no reason to expect that MRA limited only to chemicals within one silo can fully capture the risk that may be present to human consumers. Finally, we discuss possible options for implementation of MRA and we hope to prompt wider discussion of this issue.

  16. Brief Introduction of LOW/CF-Silo Control%LOW/CF-SILO控制简介

    Institute of Scientific and Technical Information of China (English)

    高永华; 王晋举

    2001-01-01

    @@埃塞俄比亚麦塞博水泥厂的生料储库采用了史密斯公司设计的CF型库,用于均化和储存生料粉,并通过库底的卸料装置向水泥窑系统实施连续喂料,与之配套的控制系统叫做LOW/CF-Silo失重连续喂料控制系统。1 系统概述LOW/CF-Silo控制系统由两部分组成,即连续流量CF-Silo(Continuous Flow)控制系统和失重喂料LOW(Loss of Weight)控制系统(图1)。1.1 LOW/CF-Silo控制系统的组成1个电动翻板阀;1套称重设备(包括3台申克称重传感器);4台恒压器;2个音叉料位计;2台气动截止阀;2台电动流量调节阀;56个电磁阀;7个接近开关;2台控制箱(箱内各装有1台LOW控制器);1台控制柜(柜内装有1台PLC5-80E控制器)。

  17. [Treatment of ulcerative colitis with spleen and kidney yang deficiency by kuijiening plaster: a randomized controlled study].

    Science.gov (United States)

    Huang, Lei; Cai, Zhi; Zhu, Ying; Wan, Hu

    2013-07-01

    To explore the clinical efficacy of ulcerative colitis with spleen and kidney yang deficiency by kuijiening plaster and the impacts on IFN-gamma and IL-4 contents, as well as make the comparison with oral medication of sulfasalzine (SASP). Sixty patients of ulcerative colitis with spleen and kidney yang deficiency were randomized into a Kuijiening plaster group, a SASP group and a combined therapy group, 20 cases in each one. In the Kuijiening plaster group, Kuijiening plaster and oral administration of placebo SASP were applied. The plaster was used at Shangjuxu (ST 37), Tianshu (ST 25), Zusanli (ST 36), Mingmen (GV 4) and Guanyuan (CV 4). In the SASP group, was applied Kuijiening plaster placebo at the points and SASP oral administration was adopted. In the combined therapy group, Kuijiening plaster and SASP oral administration were given. The duration of treatment was 60 days. The follow-up visit was 2 months after treatment. The comprehensive efficacy, the efficacy on TCM syndrome and the changes in serum IFN-gamma and IL-4 before and after treatment were compared among the three groups. The efficacy on TCM syndrome in the Kuijiening plaster was similar to the SASP group [85.0% (17/20) vs 75.0% (15/20), P > 0.05]. The efficacy on TCM syndrome in the Kuijiening plaster group was superior to the western medicine group [80.0% (16/20) vs 60.0% (12/20), P plaster group were superior to the SASP group (P plaster is effective in the treatment of ulcerative colitis of spleen and kidney yang deficiency, which is not inferior to that of SASP. The efficacy of kuijiening plaster on relieving TCM syndrome and improving body immunity is much superior to SASP. The effect is much better with SASP combined in the treatment.

  18. Innovaciones en la construcción de silos – Suiza

    Directory of Open Access Journals (Sweden)

    Huonder, A.

    1971-08-01

    Full Text Available This article gives details on sizes, construction, features, method of sealing joints, formwork, erection, etc. about these silos, which are totally prefabricated. They are a significant advance in construction time, quality of finish and total cost.Se describen en el artículo las características, dimensiones, sistemas constructivos, sellado de juntas, encofrados, montaje, etc., de estos silos totalmente prefabricados, que constituyen una novedad destacada en cuanto a rapidez de ejecución, perfección de acabado y gran economía.

  19. Discussion on Silo Flow aid Measures%刍议料仓的助流措施

    Institute of Scientific and Technical Information of China (English)

    陈兰武

    2012-01-01

    This paper discusses on the standing problems during design of silo for glass batch preparation. Some proper measures for flow-aid should be taken so as to get mass flow in the silo and stabilize float glass production.%分析介绍了玻璃配料系统料仓设计中存在的问题,需要采取合适的助流措施,以实现料仓中的物料整体流,确保浮法玻璃生产稳定。

  20. PARAMETRIC ANALYSIS OF THE BUCKLING RESISTANCE OF THE SILO STEEL WALL

    OpenAIRE

    Skejić, Davor; Cavor, Marija

    2015-01-01

    The latest final draft amendment EN 1993-4-1:2007/FprA1 brings many changes that will likely soon become valid. In this article, we assess the issue of designing steel silo walls from perspective of the proposed changes related to assessing their buckling resistance. We performed a parametric analysis, comparing the current standard, HRN EN 1993-4-1, to the proposed amendment, EN 1993-4-1:2007/FprA1, accounting for the silo fabrication quality parameter as well as variations in steel quality,...

  1. Presión en medios granulares en silos: experimentos para un curso de fluidos

    OpenAIRE

    Saulo Hernández López; Tadeo Peña Moreno; Heriberto Acuña Campa; Francisco Montes Barajas; Laura L. Yeomans Reyna.

    2015-01-01

    Se presentan las experiencias obtenidas en el análisis del comportamiento estático de un medio granular en un silo. Haciendo uso de un dispositivo experimental construido para tal fin, se explora el comportamiento de la presión ejercida sobre el fondo de un silo cuando sobre él descansa una columna de medio granular (maíz) sobrecargado y se compara con el de un líquido. Se utiliza el modelo teórico de Janssen para describir el comportamiento de la presión, obteniendo resultados satisfactorios...

  2. Preparation of Plaster Moulage (Cast in Plastic Surgery patients

    Directory of Open Access Journals (Sweden)

    Rana R

    2003-01-01

    Full Text Available The purpose of this paper is to describe the technique of making casts using alginate compound for negative and dental stone plaster for positive impressions. With certain modifications a cast could be made of any part of the body and one can make a museum of interesting cases. Casts serve as useful teaching material especially in cleft lip and palate patients to study the effect of surgery on growth and development of the cleft lip-palate-nose complex in relation to the remaining face. It also helps in planning reconstruction in cases of facial defects, recording serial changes in multistage surgery, pre-operative and post-operative comparison as in rhinoplasty, ear reconstruction, hand etc; for comparing results before and after treatment in keloid and hypertrophic scars, fabrication of implants and preparation of prosthesis. In spite of newer modalities like 3-D imaging and stereolithography, the usefulness of this old technique in certain interesting cases can not be denied.

  3. Wet or dry bandages for plaster back-slabs?

    Science.gov (United States)

    Baliga, Santosh; Finlayson, D

    2012-12-01

    Cotton crêpe and stretch bandages are commonly used in back-slabs and casts in orthopaedic practice. In theory they allow swelling to occur after injury while splinting the fracture. The application of a wet bandage prevents the Plaster-of-Paris (POP) setting too rapidly, giving time to apply a mould or attain correct limb position. However, we hypothesised that a wet bandage contracts upon drying and may cause constriction of the splint. This study aimed at determining whether there was any significant change in length of commonly used bandages when wet as well as any further change when left to dry again. Two types of bandage were evaluated. 250 mm strips of bandage were dipped into water, gently squeezed and laid flat on a bench. The bandage was then immediately measured in length. The strips were then left to dry and re-measured. This experimental study shows that both cotton crepe and cling significantly shrink by around 7% when wet. This phenomenon has the potential to significantly increase the pressure exerted on the limb by a back-slab. We speculate that the application of wet bandages is why some back-slabs may need released. It is therefore recommended that bandages should be applied only in the dry form. Copyright © 2011 Royal College of Surgeons of Edinburgh (Scottish charity number SC005317) and Royal College of Surgeons in Ireland. Published by Elsevier Ltd. All rights reserved.

  4. CTE and the Common Core Can Address the Problem of Silos

    Science.gov (United States)

    Pearson, Donna

    2015-01-01

    There is no doubt but that the education realm is replete with silos of experts of one discipline or another whose knowledge and teachings do not normally crossover into others. Yet the Common Core's call for career and college readiness virtually requires such subject integration--especially between the disciplines we consider academic and those…

  5. Who's worried about turkeys? How 'organisational silos' impede zoonotic disease surveillance.

    Science.gov (United States)

    Jerolmack, Colin

    2013-02-01

    Though emerging infectious diseases ignore boundaries between species, the agencies that respond to them do not. Based on interviews with state and federal epidemiologists, veterinarians, and physicians and on case studies of disease events, this article examines how the jurisdictional and cultural divides that exist among human and animal health agencies hinder efforts to successfully contain species-jumping diseases (zoonoses). I argue that newly emergent zoonoses make these agencies' organisational cultures function as silos because the institutionalised thinking and practices developed to address the diseases that traditionally concerned each agency constrain members from building the inter-organisational bridges required to manage the latest 'hybrid' diseases. The silo effect is evident both across the human-animal health divide and within the landscape of animal health, as agencies that monitor livestock and wildlife follow distinct and sometimes competing agendas. The article also touches on moments of inter-agency cooperation in order to specify how health practitioners can begin making connections between 'organisational silos'. This article encourages sociologists of health to explore the crucial link between animal and human health; and it introduces the concept of organisational silos to capture the relational dilemmas that arise when a 'hybrid' problem systemically links agencies with disparate organisational cultures.

  6. Packing, alignment and flow of shape-anisotropic grains in a 3D silo experiment

    Science.gov (United States)

    Börzsönyi, Tamás; Somfai, Ellák; Szabó, Balázs; Wegner, Sandra; Mier, Pascal; Rose, Georg; Stannarius, Ralf

    2016-09-01

    Granular material flowing through bottlenecks, like the openings of silos, tend to clog and thus inhibit further flow. We study this phenomenon in a three-dimensional hopper for spherical and shape-anisotropic particles by means of x-ray tomography. The x-ray tomograms provide information on the bulk of the granular filling, and allows us to determine the particle positions and orientations inside the silo. In addition, it allows us to calculate local packing densities in different parts of the container. We find that in the flowing zone of the silo particles show a preferred orientation and thereby a higher order. Similarly to simple shear flows, the average orientation of the particles is not parallel to the streamlines but encloses a certain angle with it. In most parts of the hopper, the angular distribution of the particles did not reach the one corresponding to stationary shear flow, thus the average orientation angle in the hopper deviates more from the streamlines than in stationary shear flows. In the flowing parts of the silo, shear induced dilation is observed, which is more pronounced for elongated grains than for nearly spherical particles. The clogged state is characterized by a dome, i.e. the geometry of the layer of grains blocking the outflow. The shape of the dome depends on the particle shape.

  7. Numerical simulations in granular matter: The discharge of a 2D silo

    Indian Academy of Sciences (India)

    Gabriel Pérez

    2008-06-01

    In this paper I give a short and elementary review of numerical simulations in granular assemblies, giving the process of discharge of a 2D silo as an example. The strengths and limitations of different approaches are discussed, together with some comments on the specific issues related to the numerics of discontinuous dissipative collisions.

  8. The granular silo as a continuum plastic flow: the hour-glass vs the clepsydra

    CERN Document Server

    Staron, Lydie; Popinet, Stéphane; 10.1063/1.4757390

    2012-01-01

    The granular silo is one of the many interesting illustrations of the thixotropic property of granular matter: a rapid flow develops at the outlet, propagating upwards through a dense shear flow while material at the bottom corners of the container remains static. For large enough outlets, the discharge flow is continuous; however, by contrast with the clepsydra for which the flow velocity depends on the height of fluid left in the container, the discharge rate of granular silos is constant. Implementing a plastic rheology in a 2D Navier-Stokes solver (following the mu(I)-rheology or a constant friction), we simulate the continuum counterpart of the granular silo. Doing so, we obtain a constant flow rate during the discharge and recover the Beverloo scaling independently of the initial filling height of the silo. We show that lowering the value of the coefficient of friction leads to a transition toward a different behavior, similar to that of a viscous fluid, and where the filling height becomes active in th...

  9. Density distribution of particles upon jamming after an avalanche in a 2D silo

    Directory of Open Access Journals (Sweden)

    Rodolfo O. Uñac

    2015-05-01

    Full Text Available We present a complete analysis of the density distribution of particles in a two dimensional silo after discharge. Simulations through a pseudo-dynamic algorithm are performed for filling and subsequent discharge of a plane silo. Particles are monosized hard disks deposited in the container and subjected to a tapping process for compaction. Then, a hole of a given size is open at the bottom of the silo and the discharge is triggered. After a clogging at the opening is produced, and equilibrium is restored, the final distribution of the remaining particles at the silo is analyzed by dividing the space into cells with different geometrical arrangements to visualize the way in which the density depression near the opening is propagated throughout the system. The different behavior as a function of the compaction degree is discussed. Received: 9 December 2014, Accepted: 13 April 2015; Edited by: L. A. Pugnaloni; Reviewed by: F. Vivanco, Dpto. de Física, Universidad de Santiago de Chile, Chile; DOI: http://dx.doi.org/10.4279/PIP.070007 Cite as: R. O. Uñac, J. L. Sales, M. V. Gargiulo, A. M. Vidales, Papers in Physics 7, 070007 (2015

  10. Persistence strategies of Bacillus cereus spores isolated from dairy silo tanks.

    Science.gov (United States)

    Shaheen, Ranad; Svensson, Birgitta; Andersson, Maria A; Christiansson, Anders; Salkinoja-Salonen, Mirja

    2010-05-01

    Survival of Bacillus cereus spores of dairy silo tank origin was investigated under conditions simulating those in operational dairy silos. Twenty-three strains were selected to represent all B. cereus isolates (n = 457) with genotypes (RAPD-PCR) that frequently colonised the silo tanks of at least two of the sampled eight dairies. The spores were studied for survival when immersed in liquids used for cleaning-in-place (1.0% sodium hydroxide at pH 13.1, 75 degrees C; 0.9% nitric acid at pH 0.8, 65 degrees C), for adhesion onto nonliving surfaces at 4 degrees C and for germination and biofilm formation in milk. Four groups with different strategies for survival were identified. First, high survival (log 15 min kill steel from cold water. Third, a cereulide producing group with spores characterised by slow germination in rich medium and well preserved viability when exposed to heating at 90 degrees C. Fourth, spores capable of germinating at 8 degrees C and possessing the cspA gene. There were indications that spores highly resistant to hot 1% sodium hydroxide may be effectively inactivated by hot 0.9% nitric acid. Eight out of the 14 dairy silo tank isolates possessing hot-alkali resistant spores were capable of germinating and forming biofilm in whole milk, not previously reported for B. cereus.

  11. Breaking down IT silos: a "connected" way to improve customer experience and the bottom line.

    Science.gov (United States)

    Hallowell, Bruce; Turisco, Frances

    2009-03-01

    Hospitals can provide customer service like Amazon.com without purchasing new technology. Making technology interactive requires sharing patient data across applications and enhancing existing IT with decision support. Breaking down technology silos between hospital and outpatient care provider systems significantly improves efficiency, lowers costs, and speeds care delivery.

  12. The granular silo as a continuum plastic flow: The hour-glass vs the clepsydra

    Science.gov (United States)

    Staron, L.; Lagrée, P.-Y.; Popinet, S.

    2012-10-01

    The granular silo is one of the many interesting illustrations of the thixotropic property of granular matter: a rapid flow develops at the outlet, propagating upwards through a dense shear flow while material at the bottom corners of the container remains static. For large enough outlets, the discharge flow is continuous; however, by contrast with the clepsydra for which the flow velocity depends on the height of fluid left in the container, the discharge rate of granular silos is constant. Implementing a plastic rheology in a 2D Navier-Stokes solver (following the μ(I)-rheology or a constant friction), we simulate the continuum counterpart of the granular silo. Doing so, we obtain a constant flow rate during the discharge and recover the Beverloo scaling independently of the initial filling height of the silo. We show that lowering the value of the coefficient of friction leads to a transition toward a different behavior, similar to that of a viscous fluid, and where the filling height becomes active in the discharge process. The pressure field shows that large enough values of the coefficient of friction (≃0.3) allow for a low-pressure cavity to form above the outlet, and can thus explain the Beverloo scaling. In conclusion, the difference between the discharge of a hourglass and a clepsydra seems to reside in the existence or not of a plastic yield stress.

  13. The discharge of fine silica sand in a silo under different ambient air pressures

    Science.gov (United States)

    Hsiau, Shu-San; Liao, Chun-Chung; Lee, Jie-Hsien

    2012-04-01

    Silos are widely used for the industrial scale handling and transportation of powdered and granular materials. The process of discharging powder in a silo involves the flow of both solid particles and an interstitial fluid, usually air. In this study, we experimentally investigate the effects of particle size and ambient pressure on the discharge process in open- and closed-top silos. The discharge rate, pressure drop, and pressure recovery rate are measured and discussed. The results show that the particle size, the diameter of the orifice, and the ambient pressure significantly influence the process of discharge. The effect of air flow is stronger on fine-powdered flow in a closed-top silo. The results indicate that the effects of air flow could be reduced by lowering the ambient pressure. In addition, a normalized critical pressure can be defined beyond which the discharge rate increases dramatically. With reduced ambient pressure, this normalized critical pressure decreases with increasing particle size. Finally, the experimental results are compared with results calculated using the Beverloo equation and Darcy's law.

  14. Análise estrutural de silos metálicos prismáticos Structural analysis of prismatic metallic silos

    Directory of Open Access Journals (Sweden)

    José Pinheiro Lopes Neto

    2008-08-01

    Full Text Available Nos últimos anos, o crescimento da agricultura brasileira tem forçado vários setores a se adequarem aos padrões produtivos com o intuito de se manterem competitivos, frente ao processo de globalização econômica. Nesse contexto, as fábricas de ração avícola tendem a buscar novas alternativas que favoreçam a produção e reduzam custos sem afetar a qualidade do produto final. Entre essas alternativas, destaca-se o uso de silos verticais por facilitar o processo de confecção das rações e eliminar os grandes depósitos horizontais. Diante dessa possibilidade, objetivou-se, com a presente pesquisa, estudar as tensões nas paredes em conformação ziguezague de um silo metálico prismático 2m x 1m e comparar os resultados obtidos com teorias e normas. Para o cálculo das tensões, utilizaram-se os métodos simplificados de Ravenet e Troitsky. Para a obtenção dos esforços reais nas paredes, utilizaram-se extensômetros elétricos. Dessa forma, conclui-se que, tanto a teoria de Ravenet quanto de Troistky, podem ser recomendadas para o dimensionamento de silos prismáticos por apresentarem boa aproximação com valores experimentais.Recently Brazil has undergone agricultural growth that has forced several sectors to adjust their business structure to maintain competitiveness within the process of economic globalization. In this context, the poultry production has focused on new alternatives to increase productivity and reduce costs without affecting the quality of the final product. Among these alternatives, the use of vertical silos due to their capacity and ease of accurate feed ingredient rationing and eliminate large horizontal warehouses. The present research has focused on the stresses in rectangular, hopper bottom bins with a unique zigzag corrugation. The model bin was 2m x 1m with a hopper and the stresses obtained were compared to theories and standards. The stresses were estimated using Ravenet and Troitsky's simplified

  15. Comparison of space analysis performed on plaster vs. digital dental casts applying Tanaka and Johnston's equation.

    Science.gov (United States)

    Sanches, Júlia Olien; dos Santos-Pinto, Lourdes Aparecida Martins; dos Santos-Pinto, Ary; Grehs, Betina; Jeremias, Fabiano

    2013-01-01

    The purpose of this study was to compare dental size measurements, their reproducibility and the application of Tanaka and Johnston regression equation in predicting the size of canines and premolars on plaster and digital dental casts. Thirty plaster casts were scanned and digitized. Mesiodistal measurements of the teeth were then performed with a digital caliper on the plaster and digital casts using O3d software system (Widialabs©).The sum of the sizes of the lower incisors was used to obtain predictive values of the sizes of the premolars and canines using the regression equation, and these values were compared with the actual sizes of the teeth. The data were statistically analyzed by applying to the results Pearson's correlation test, Dahlberg's formula, paired t-test and analysis of variance (p plaster and digital casts. Despite an adequate reproducibility of the measurements performed on both casts, most measurements on the digital casts were higher than those on the plaster casts. The predicted space was overestimated in both models and significantly higher in the digital casts.

  16. The influence of composition of gypsum plaster on its technological properties

    Directory of Open Access Journals (Sweden)

    M. Pawlak

    2010-10-01

    Full Text Available Gypsum plasters used in art and precision foundry always are the composition of gypsum-silica-cristobalite. It is necessary considering the specifity of plaster during heating stage. Plaster undergoes then, structural transformations causing significant variations of its volume which are nonuniform and proceed with different intensity. The content of silica and cristobalite reduces dimensional variations of setted gypsum plaster what increases dimensional accuracy and significant stresses reduction limiting the possibility of mould cracks occurrence during heating.The influence of cristobalite and silica addition on basic gypsum plaster properties like setting time, dimensional changes after setting, bending strength and permeability in raw and heat treated state are presented in this paper. Experiments were done for mixes containing 30÷70% of the gypsum. It was proven that cristobalite has the biggest influence on the bounding time and expansion of the sandmix and the strength and permeability do not depend on the type of additions and only on theirs total amount in the composition.

  17. Application of Ceramic Powder as Supplementary Cementitious Material in Lime Plasters

    Directory of Open Access Journals (Sweden)

    Monika ČÁCHOVÁ

    2016-09-01

    Full Text Available In this paper, the properties of plasters based on lime – brick powder binder of varying composition (ceramics content from 0 to 80 % are studied. The plasters are prepared with a constant water amount. The pore size distribution is thus influenced in a positive way; the total porosity increases with the ceramics content but the volume of capillary pores is reduced. It results in lower water vapor diffusion resistance factor while the apparent moisture diffusivity coefficient increases just moderately. The influence of ceramic on strength of plasters is not found very important. The thermal conductivity of plasters containing ceramics is lower than those with the pure lime what is again in agreement with the pore size distribution. It can be concluded that fine brick powder can be used as pozzolanic admixture in lime based plasters with a positive influence on its functional parameters.DOI: http://dx.doi.org/10.5755/j01.ms.22.3.7433

  18. Antihyperalgesic efficacy of 5% lidocaine medicated plaster in capsaicin and sunburn pain models--two randomized, double-blinded, placebo-controlled crossover trials in healthy volunteers.

    Science.gov (United States)

    Gustorff, Burkhard; Hauer, David; Thaler, Johannes; Seis, Astrid; Draxler, Julia

    2011-12-01

    The aim of this research is to analyze analgesic efficacy of the 5% lidocaine medicated plaster in two randomized, double-blinded, placebo-controlled, crossover studies in 16 healthy volunteers using capsaicin and sunburn pain models. Lidocaine and placebo plasters were simultaneously applied to forearms and thighs at contralateral body sites for three alternating 12-h plaster-on/plaster-off periods. Between the second and third plaster-on period, 4.2-cm circular spots on both pretreated thighs were irradiated with three times the individual minimal erythema dose of UVB light. After the last plaster-on period, 20 μl of 0.1% capsaicin was injected intradermally into both forearms. The study was repeated using a single 12-h plaster application. The area of pinprick hyperalgesia was diminished by 53% (p plaster effectively treats mechanical hyperalgesia and cold pain.

  19. Utilization of ground waste seashells in cement mortars for masonry and plastering.

    Science.gov (United States)

    Lertwattanaruk, Pusit; Makul, Natt; Siripattarapravat, Chalothorn

    2012-11-30

    In this research, four types of waste seashells, including short-necked clam, green mussel, oyster, and cockle, were investigated experimentally to develop a cement product for masonry and plastering. The parameters studied included water demand, setting time, compressive strength, drying shrinkage and thermal conductivity of the mortars. These properties were compared with those of a control mortar that was made of a conventional Portland cement. The main parameter of this study was the proportion of ground seashells used as cement replacement (5%, 10%, 15%, or 20% by weight). Incorporation of ground seashells resulted in reduced water demand and extended setting times of the mortars, which are advantages for rendering and plastering in hot climates. All mortars containing ground seashells yielded adequate strength, less shrinkage with drying and lower thermal conductivity compared to the conventional cement. The results indicate that ground seashells can be applied as a cement replacement in mortar mixes and may improve the workability of rendering and plastering mortar.

  20. Computational modeling of latent-heat-storage in PCM modified interior plaster

    Science.gov (United States)

    Fořt, Jan; Maděra, Jiří; Trník, Anton; Pavlíková, Milena; Pavlík, Zbyšek

    2016-06-01

    The latent heat storage systems represent a promising way for decrease of buildings energy consumption with respect to the sustainable development principles of building industry. The presented paper is focused on the evaluation of the effect of PCM incorporation on thermal performance of cement-lime plasters. For basic characterization of the developed materials, matrix density, bulk density, and total open porosity are measured. Thermal conductivity is accessed by transient impulse method. DSC analysis is used for the identification of phase change temperature during the heating and cooling process. Using DSC data, the temperature dependent specific heat capacity is calculated. On the basis of the experiments performed, the supposed improvement of the energy efficiency of characteristic building envelope system where the designed plasters are likely to be used is evaluated by a computational analysis. Obtained experimental and computational results show a potential of PCM modified plasters for improvement of thermal stability of buildings and moderation of interior climate.

  1. Effect of Tai Chi exercise in combination with auricular plaster on patients with lumbar muscle strain.

    Science.gov (United States)

    Lu, Tao; Song, Qing-Hua; Xu, Rong-Mei; Zhang, Li-Yan

    2015-01-01

    observe the effect of Tai Chi exercise on the patients with the chronic lumbar muscle strain under the intervention treatment of auricular plaster. 74 middle-aged and elderly patients, suffering from the chronic lumbar muscle strain, are randomly and equally divided into an observation group and a control group, with 37 patients in each group. The patients in the control group do Tai Chi exercise, while those in the observation group are treated by the auricular plaster therapy in addition to Tai Chi exercise. Evaluate and compare the disease conditions of the patients in the two groups before the treatment and after 12 weeks' treatment. after 12 weeks' treatment, the patients in the two groups have been improved differently in comparison with those before the treatment (P plaster therapy.

  2. Computational modeling of latent-heat-storage in PCM modified interior plaster

    Energy Technology Data Exchange (ETDEWEB)

    Fořt, Jan; Maděra, Jiří; Trník, Anton; Pavlíková, Milena; Pavlík, Zbyšek [Department of Materials Engineering and Chemistry, Faculty of Civil Engineering, Czech Technical University in Prague, Thákurova 7, 166 29 Prague (Czech Republic)

    2016-06-08

    The latent heat storage systems represent a promising way for decrease of buildings energy consumption with respect to the sustainable development principles of building industry. The presented paper is focused on the evaluation of the effect of PCM incorporation on thermal performance of cement-lime plasters. For basic characterization of the developed materials, matrix density, bulk density, and total open porosity are measured. Thermal conductivity is accessed by transient impulse method. DSC analysis is used for the identification of phase change temperature during the heating and cooling process. Using DSC data, the temperature dependent specific heat capacity is calculated. On the basis of the experiments performed, the supposed improvement of the energy efficiency of characteristic building envelope system where the designed plasters are likely to be used is evaluated by a computational analysis. Obtained experimental and computational results show a potential of PCM modified plasters for improvement of thermal stability of buildings and moderation of interior climate.

  3. The influence of inner hydrophobisation on water transport properties of modified lime plasters

    Science.gov (United States)

    Pavlíková, Milena; Pavlík, Zbyšek; Pernicová, Radka; Černý, Robert

    2016-06-01

    The effect of hydrophobic agent admixture on water vapour and liquid water transport properties of newly designed lime plasters is analysed in the paper. The major part of physico - chemical building deterioration is related to the penetration of moisture and soluble salts into the building structure. For that reason, the modified lime plasters were in the broad range of basic material properties tested. From the quantitative point of view, the measured results clearly demonstrate the big differences in the behaviour of studied materials depending on applied modifying admixtures. From the practical point of view, plaster made of lime hydrate, metakaolin, zinc stearate and air-entraining agent can be recommended for renovation purposes. The accessed material parameters will be used as input data for computational modelling of moisture transport in this type of porous building materials and will be stored in material database.

  4. Influence of Auricular Plaster Therapy on Sleeping Structure in OSAS Patients

    Institute of Scientific and Technical Information of China (English)

    WANG Xiao-hong; XIAO Lan-ying; WANG Bao-fa; YUAN Ya-dong; PAN Wen-sen; SHI Yu-zhen

    2009-01-01

    To evaluate the therapeutic effects of auricular plaster therapy for obstructive sleep apnea syndrome (OSAS) and the influence on sleeping structure. Methods: 45 OSAS patients were randomly divided into a treatment group of 30 cases and a control group of 15 cases for comparison of the changes in parameters of respiration and sleep at night. Results: The auricular plaster therapy significantly improved the hypoventilation index, respiratory disturbance index and other respiratory parameters as well as the sleeping parameters such as the time and rate of sleep at stage Ⅰ and Ⅱ, and the waking time and rate.Conclusion: Auricular plaster therapy may show good therapeutic effects for OSAS, and with the advantages of low cost and less side effects.

  5. [Ambulatory prevention of thrombosis with low molecular weight heparin in plaster immobilization of the lower extremity].

    Science.gov (United States)

    Kock, H J; Schmit-Neuerburg, K P; Hanke, J; Hakmann, A; Althoff, M; Rudofsky, G; Hirche, H

    1993-06-01

    Plaster cast immobilisation following trauma is a major risk factor for the development of deep vein thrombosis. In our controlled, randomized and prospective study on patients with minor injuries incidence of DVT in conservatively treated out-patients with plaster cast immobilisation of the leg was 3.9% in the control group (n = 126) without prophylaxis. By s.c. self-application of LMV heparin once daily the number of DVT in the prophylaxis group (n = 115) was reduced to 0. No severe side effects of NMH were observed. We conclude that thromboprophylaxis with LMW heparin once daily up to now conspiciously reduced the risk of DVT in outpatients with plaster cast immobilisation of the leg.

  6. CLINICAL OBSERVATION ON TREATMENT OF 61 CASES OF INSOMNIA WITH AURICULAR PLASTER THERAPY

    Institute of Scientific and Technical Information of China (English)

    张家彤; 王月

    2003-01-01

    Objective: To observe the therapeutic effect of auricular plaster (otopoint-pressure) therapy in thetreatment of insomnia. Methods: In this paper, 61 cases of insomnia patients including 16 males and 45 females weretreated with Ershenmen (MA-TF 1), Zhen (MA-AT), Yuanzhong (MA-AT), Nao Dian and E (MA-AT), combined withother otopoints according to symptoms. The otopoint was stuck with a piece of plaster adhered with vaccaria seeds andpressured by the patient him- or her-self. The treatment was given twice a week, with 7 times being a therapeuticcourse. Results: After 1 - 2 courses of treatment, 19 (31.15%) cases were cured, 34 (55.74 % ) had improvementand 8 (13.11%) had no changes, with the total effective rate being 86.9%. Conclusion: Auricular plaster therapyworks well in the treatment of insomnia patient.

  7. Monitoring of the moisture and salt load in restoration plasters in St.-Barbara' s church in Culemborg

    NARCIS (Netherlands)

    Hees, R.P.J. van; Sanders, M.M.

    2005-01-01

    St. Barbara's Church in Culemborg in the Netherlands has a history of moisture and salt damage to the plaster. In the past several restorations were performed, without a durable results. Finally, in 1997 test panels were applied in oreder to bas the choice for new plastering on in practice proved

  8. Evaluation of physical-mechanical properties of 3 brands of plaster of Paris in the Kenyan market.

    Science.gov (United States)

    Mwaniki, D L

    1990-05-01

    In this study, 3 brands of plaster of Paris that are available in the Kenyan Market for prosthetics and dental rehabilitation uses were subjected to physical-mechanical tests. The particles in two of the brands that had been imported were finer than a locally made plaster since less than 1.41% of their particles were larger than 150 microns compared to 15.2% in the local plaster. The range of their setting times was between 7.5 and 27.5 min. and was within the International Standards Organisation (ISO) recommendation. The water:power ratios required to produce plaster mixes of standard consistency for the locally made plaster was about 1.5 times of other brands. In compression, the mean 1-hour strength of local plaster was 2.5 MN/m2 (Mega Newtons per square metre) compared to 6.81 MN/m2 and 8.95 MN/m2 for the other brands. The differences between these strength values were highly significant (p less than 0.01). There were no significant differences in deformation of fracture for the 3 brands whose range was 1.32% to 1.71%. In order to obviate the need to import plaster, strict manufacturing techniques of locally made plaster are recommended.

  9. Accuracy and reproducibility of measurements on plaster models and digital models created using an intraoral scanner.

    Science.gov (United States)

    Camardella, Leonardo Tavares; Breuning, Hero; de Vasconcellos Vilella, Oswaldo

    2017-05-01

    The purpose of the present study was to evaluate the accuracy and reproducibility of measurements made on digital models created using an intraoral color scanner compared to measurements on dental plaster models. This study included impressions of 28 volunteers. Alginate impressions were used to make plaster models, and each volunteers' dentition was scanned with a TRIOS Color intraoral scanner. Two examiners performed measurements on the plaster models using a digital caliper and measured the digital models using Ortho Analyzer software. The examiners measured 52 distances, including tooth diameter and height, overjet, overbite, intercanine and intermolar distances, and the sagittal relationship. The paired t test was used to assess intra-examiner performance and measurement accuracy of the two examiners for both plaster and digital models. The level of clinically relevant differences between the measurements according to the threshold used was evaluated and a formula was applied to calculate the chance of finding clinically relevant errors on measurements on plaster and digital models. For several parameters, statistically significant differences were found between the measurements on the two different models. However, most of these discrepancies were not considered clinically significant. The measurement of the crown height of upper central incisors had the highest measurement error for both examiners. Based on the interexaminer performance, reproducibility of the measurements was poor for some of the parameters. Overall, our findings showed that most of the measurements on digital models created using the TRIOS Color scanner and measured with Ortho Analyzer software had a clinically acceptable accuracy compared to the same measurements made with a caliper on plaster models, but the measuring method can affect the reproducibility of the measurements.

  10. Effect of cotton padding on the setting properties of plaster slabs.

    Science.gov (United States)

    Barlow, D; Bansal, R; Barlow, T; Rhee, S J; Kuiper, J H; Makwana, N K

    2013-03-01

    Plaster of Paris (PoP) impregnated bandages have been used to maintain the position of bones and joints for over a century. Classically, wool dressing is applied to the limb before the PoP, which can then be moulded to the desired shape. A modification of this practice is to wrap the PoP bandages circumferentially in cotton before wetting and applying to the patient in an attempt to reduce inhalation of plaster dust and reduce mess. However, this may affect the water content of the cast and therefore also its setting properties and strength. This study compared the setting properties of PoP casts when used with and without cotton wrapping. Sixty specimens, compliant with the American Society for Testing and Materials standards for three-point bending tests, were prepared, with thirty wrapped in cotton. All were weighed before and after water immersion, and wrapped around a plastic cylinder to mimic limb application. Bending stiffness and yield strength was measured on a servohydraulic materials testing machine at 2, 6, 12, 24, 48 and 72 hours. The water content of cotton-wrapped plaster was significantly higher (50%) than that of standard plaster. It had significantly lower strength up to 24 hours and significantly lower stiffness up to 72 hours. The initial decrease in strength and stiffness of the cast wrapped in cotton may comprise the ability of the backslab to hold the joint or bone in an optimal position. Any modification of the standard plaster slab application technique should allow for the potential adverse effects on the plaster setting properties.

  11. A Comparative Evaluation of Mixed Dentition Analysis on Reliability of Cone Beam Computed Tomography Image Compared to Plaster Model.

    Science.gov (United States)

    Gowd, Snigdha; Shankar, T; Dash, Samarendra; Sahoo, Nivedita; Chatterjee, Suravi; Mohanty, Pritam

    2017-01-01

    The aim of the study was to evaluate the reliability of cone beam computed tomography (CBCT) obtained image over plaster model for the assessment of mixed dentition analysis. Thirty CBCT-derived images and thirty plaster models were derived from the dental archives, and Moyer's and Tanaka-Johnston analyses were performed. The data obtained were interpreted and analyzed statistically using SPSS 10.0/PC (SPSS Inc., Chicago, IL, USA). Descriptive and analytical analysis along with Student's t-test was performed to qualitatively evaluate the data and P plaster model; the mean for Moyer's analysis in the left and right lower arch for CBCT and plaster model was 21.2 mm, 21.1 mm and 22.5 mm, 22.5 mm, respectively. CBCT-derived images were less reliable as compared to data obtained directly from plaster model for mixed dentition analysis.

  12. Efficacy of the topical 5% lidocaine medicated plaster in the treatment of chronic post-thoracotomy neuropathic pain.

    Science.gov (United States)

    Sansone, Pasquale; Passavanti, Maria Beatrice; Fiorelli, Alfonso; Aurilio, Caterina; Colella, Umberto; De Nardis, Lorenzo; Donatiello, Valerio; Pota, Vincenzo; Pace, Maria Caterina

    2017-05-01

    To assess the efficacy of the topical 5% lidocaine medicated plaster (Versatis(®), Grünenthal GmbH, Aachen, Germany) in patients with post-thoracotomy neuropathic pain. Patients were randomized to receive the topical 5% lidocaine medicated plaster (n = 33) or non-medicated placebo plasters (n = 30) for 12 h every day for 8 weeks. Laser-evoked potentials (LEPs) were measured, and various questionnaires/scales completed. Numeric Rating Scale pain scores improved significantly (p plaster than in placebo recipients. The same was true for N2 and P2 LEP latency and amplitude, and other parameters. The study included neurophysiological findings and confirmed the efficacy of the topical 5% lidocaine medicated plaster in patients with chronic post-thoracotomy neuropathic pain.

  13. Parametric design of silo steel framework of concrete mixing station based on the finite element method and MATLAB

    Directory of Open Access Journals (Sweden)

    Long Hui

    2016-01-01

    Full Text Available When the structure of the silo steel framework of concrete mixing station is designed, In most cases, the dimension parameters, shape parameters and position parameters of silo steel framework beams are changed as the productivity adjustment of the concrete mixing station, but the structure types of silo steel framework will remain the same. In order to acquire strength of silo steel framework rapidly and efficiently, it is need to provide specialized parametric strength computational software for engineering staff who does not understand the three-dimensional software such as PROE and finite element analysis software. By the finite element methods(FEM, the parametric stress calculation modal of the silo steel framework of concrete mixing station is established, which includes dimension parameters, shape parameters, position parameters and applied load parameters of each beams, and then the parametric calculation program is written with MATLAB. The stress equations reflect the internal relationship between the stress of the silo steel frames with the dimension parameters, shape parameters, position parameters and load parameters. Finally, an example is presented, the calculation results show the stress of all members and the size and location of the maximum stress, which agrees well with realistic cases.

  14. Far infrared emitting plaster in knee osteoarthritis: a single blinded, randomised clinical trial

    Directory of Open Access Journals (Sweden)

    N. Marino

    2012-12-01

    Full Text Available Objective. Therapeutic approach of osteoarthritis (OA still represents a challenge in clinical practice. The aim of the study is to assess the efficacy of far infrared (FIR emitting plaster in the treatment of knee OA. Design. This is a randomized, single-blind, placebo-controlled, parallel group with equal randomization (1:1, clinical trial. Patients affected by knee OA were randomly allocated to 1 of 2 treatment groups, either placebo plaster or far infrared emitting plaster. Primary endpoint was to assess pain improvement from baseline to 1 months posttreatment in the visual analogue score (VAS. Secondary end point was to evaluate pain score after 1 week of treatment and to compare ultrasonographic findings after 1 month of treatment. Results. Each group comprised 30 (in the FIR group and 30 (in the placebo group completers. VAS scores of the placebo and the FIR group were significantly lower at 1 week post-treatment (95% confidence interval CI = -1.14 to 0.31; PConclusions. Far infrared emitting plaster could be considered an effective non-pharmacological choice for the therapeutic management of knee OA.

  15. Health economic evidence of 5% lidocaine medicated plaster in post-herpetic neuralgia.

    Science.gov (United States)

    Liedgens, Hiltrud; Obradovic, Marko; Nuijten, Mark

    2013-11-25

    Post-herpetic neuralgia (PHN) is the most common and most debilitating complication of herpes zoster, and involves considerable associated costs. This paper presents results from nine health economic studies undertaken in eight European countries that compared lidocaine medicated plaster with gabapentin and/or pregabalin in PHN. It aims to support the increasing need for published cost-effectiveness data for health care decision-making processes in Europe. All studies were based on a similar core Markov model with data derived from clinical trials, local Delphi panels, and official national price and tariff lists. The main outcome measure was cost per quality-adjusted life year gained; time without pain or intolerable adverse events was also included as a secondary outcome measure. All studies focused on an elderly population of patients with PHN who had insufficient pain relief with standard analgesics and could not tolerate or had contraindications to tricyclic antidepressants. Despite considerable differences in many of the variables used, the results showed remarkable similarity and suggested that use of lidocaine medicated plaster offered cost-savings in many of the countries studied, where it proved a highly cost-effective alternative to both gabapentin and pregabalin. Lidocaine medicated plaster is a cost-effective alternative to gabapentin and pregabalin in the treatment of PHN. These savings are largely the result of the superior safety profile of the lidocaine medicated plaster.

  16. Fragmentation, Cost and Environmental Effects of Plaster Stemming Method for Blasting at A Basalt Quarry

    Science.gov (United States)

    Cevizci, Halim

    2014-10-01

    In this study, the plaster stemming application for blasting at a basalt quarry is studied. Drill cuttings are generally used in open pits and quarries as the most common stemming material since these are most readily available at blast sites. However, dry drill cuttings eject very easily from blastholes without offering much resistance to blast energy. The plaster stemming method has been found to be better than the drill cuttings stemming method due to increased confinement inside the hole and better utilization of blast explosive energy in the rock. The main advantage of the new stemming method is the reduction in the cost of blasting. At a basalt quarry, blasting costs per unit volume of rock were reduced to 15% by increasing burden and spacing distances. In addition, better fragmentation was obtained by using the plaster stemming method. Blast trials showed that plaster stemming produced finer material. In the same blast tests, +30 cm size fragments were reduced to 47.3% of the total, compared to 32.6% in the conventional method of drill cuttings stemming. With this method of stemming, vibration and air shock values increased slightly due to more blast energy being available for rock breakage but generally these increased values were small and stayed under the permitted limit for blast damage criteria unless measuring distance is too close.

  17. Digital model as an alternative to plaster model in assessment of space analysis.

    Science.gov (United States)

    Kumar, A Anand; Phillip, Abraham; Kumar, Sathesh; Rawat, Anuradha; Priya, Sakthi; Kumaran, V

    2015-08-01

    Digital three-dimensional models are widely used for orthodontic diagnosis. The purpose of this study was to appraise the accuracy of digital models obtained from computer-aided design/computer-aided manufacturing (CAD/CAM) and cone-beam computed tomography (CBCT) for tooth-width measurements and the Bolton analysis. Digital models (CAD/CAM, CBCT) and plaster model were made for each of 50 subjects. Tooth-width measurements on the digital models (CAD/CAM, CBCT) were compared with those on the corresponding plaster models. The anterior and overall Bolton ratios were calculated for each participant and for each method. The paired t-test was applied to determine the validity. Tooth-width measurements, anterior, and overall Bolton ratio of digital models of CAD/CAM and CBCT did not differ significantly from those on the plaster models. Hence, both CBCT and CAD/CAM are trustable and promising technique that can replace plaster models due to its overwhelming advantages.

  18. Index of Complexity, Outcome and Need scored on plaster and digital models.

    NARCIS (Netherlands)

    Veenema, A.C.; Katsaros, C.; Boxum, S.C.; Bronkhorst, E.M.; Kuijpers-Jagtman, A.M.

    2009-01-01

    The aim of this study was to compare standard plaster models with their digital counterparts for the applicability of the Index of Complexity, Outcome, and Need (ICON). Generated study models of 30 randomly selected patients: 30 pre- (T(0)) and 30 post- (T(1)) treatment. Two examiners, calibrated in

  19. Index of Complexity, Outcome and Need scored on plaster and digital models

    NARCIS (Netherlands)

    Veenema, A. C.; Katsaros, C.; Boxum, S. C.; Bronkhorst, E. M.; Kuijpers-Jagtman, A. M.

    2009-01-01

    The aim of this study was to compare standard plaster models with their digital counterparts for the applicability of the Index of Complexity, Outcome, and Need (ICON). Generated study models of 30 randomly selected patients: 30 pre- (T-0) and 30 post- (T-1) treatment. Two examiners, calibrated in t

  20. Treatment of localized neuropathic pain after disk herniation with 5% lidocaine medicated plaster

    Science.gov (United States)

    Likar, Rudolf; Kager, Ingo; Obmann, Michael; Pipam, Wolfgang; Sittl, Reinhard

    2012-01-01

    Objective To assess treatment with the 5% lidocaine medicated plaster for peripheral neuropathic pain after disk herniation. Study design Case series, single center, retrospective data. Patients and methods Data of 23 patients treated for neuropathic pain with the lidocaine plaster for up to 24 months after a protrusion or prolapse of the cervical, thoracic, or lumbar vertebral disks were retrospectively analyzed. Changes in overall pain intensity, in intensity of different pain qualities and of allodynia and hyperalgesia were evaluated. Results Patients (14 female/nine male, mean age 53.5 ± 10.4 years) presented with radiating pain into the abdomen, back, neck, shoulder, or legs and feet with a mean pain intensity of 8.3 ± 1.5 on the 11-point Likert scale. Mean treatment duration was 7.6 months; 52% of the patients received lidocaine plaster as monotherapy. At the end of the observation, mean overall pain intensity had been reduced to 3.1 ± 1.8. All other parameters also improved. The treatment was well tolerated. Conclusion These results point to a safe and effective treatment approach with 5% lidocaine medicated plaster for localized neuropathic pain related to disk herniation. However, owing to the small sample size, further investigation in a larger-scale controlled trial is warranted. PMID:22973116

  1. [Exposure to hand-arm vibrations in orthopaedic plaster room: risk management].

    Science.gov (United States)

    Lembo, Marco; Lunghi, Alessandro; Leo, Erica; Ritrovato, Matteo; Cannatà, Vittorio; Capussotto, Carlo; Tirabasso, Angelo; Zaffina, Salvatore; Camisa, Vincenzo; Derrico, Pietro; Martella, Mauro; Marchetti, Enrico

    2016-03-24

    In hospitals, the use of vibrating tools, such as oscillating saws to cut plaster, can expose the staff to hand-arm vibrations. The aim of the study was to assess the exposure of workers to vibrations in the plaster room and then  identify the most appropriate  intervention for  prevention and protection to be implemented in order to minimize  exposure and  protect  workers' health, considering different individual hyper-susceptibility conditions. Four different models of plaster saws were examined for the evaluation.  Various measurements were made in normal working conditions of the operators. The values of acceleration and noise detected on the instruments  were  in line with those reported in the literature. The preventive measure adopted (replacing plaster saws currently used in the hospital with similar ones with lower vibration emission) was an adequate means of protection. Health surveillance activities  recorded a higher level of wellbeing, both environmentally and individually and, specifically, an increased protection level for the hyper-susceptibility conditions observed during health checks of exposed personnel  which will be monitored regularly by the Occupational Health Service.

  2. Mineralogical and textural characterization of mortars and plasters from the archaeological site of Barsinia, northern Jordan

    Directory of Open Access Journals (Sweden)

    Mustafa Mohammad AL-Naddaf

    2014-12-01

    Full Text Available Twelve mortar and plaster samples excavated in the archaeological site of Barsinia were mineralogically and petrographically examined by XRay Diffraction (XRD and Stereo and Polarized Light Microscopy, while the total carbonate content was measured using a DietrichFruhling Calcimeter. The physical properties of the samples, such as water uptake under atmospheric pressure and under vacuum, together with density and porosity, were measured. Only twelve samples were available for the purposes of this study: 8 plaster samples and 4 mortar samples. Eleven samples out of the total number of samples were mortars or plasters with lime binder and silica aggregate; calcite and quartz were identified in all of these samples. In most of the samples one or more pozzolanic components were detected; a hydraulic effect therefore exists in practically most of the studied mortars. Excluding the plasters taken from waterbearing constructions such as cisterns, and the mortar sample from the compact floor, the binder content is high; in general, the overall porosity of the studied samples is high. Porosity and petrographic investigation results suggest that the burning temperature of the limestone was low and/or the duration of the combustion was short; such preparation conditions produce a desirable quicklime. Owing to the significant compositional and textural differences between the samples that were reported, there is consequently no suitable general mortar that can be adopted for the restoration of the whole site.

  3. [Toxic mustard plaster dematitis and phototoxic dematitis after application of bergamot oil].

    Science.gov (United States)

    Weisenseel, P; Woitalla, S

    2005-12-15

    Two cases that illustrate the risks attendant on the therapeutic use of natural medications by laypersons are reported. In the first case, the application of a mustard plaster triggered toxic dermatitis. In the second case, a session in a solarium after the external application of bergamot oil resulted in a phototoxic reaction.

  4. Treatment of localized neuropathic pain after disk herniation with 5% lidocaine medicated plaster.

    Science.gov (United States)

    Likar, Rudolf; Kager, Ingo; Obmann, Michael; Pipam, Wolfgang; Sittl, Reinhard

    2012-01-01

    To assess treatment with the 5% lidocaine medicated plaster for peripheral neuropathic pain after disk herniation. Case series, single center, retrospective data. Data of 23 patients treated for neuropathic pain with the lidocaine plaster for up to 24 months after a protrusion or prolapse of the cervical, thoracic, or lumbar vertebral disks were retrospectively analyzed. Changes in overall pain intensity, in intensity of different pain qualities and of allodynia and hyperalgesia were evaluated. Patients (14 female/nine male, mean age 53.5 ± 10.4 years) presented with radiating pain into the abdomen, back, neck, shoulder, or legs and feet with a mean pain intensity of 8.3 ± 1.5 on the 11-point Likert scale. Mean treatment duration was 7.6 months; 52% of the patients received lidocaine plaster as monotherapy. At the end of the observation, mean overall pain intensity had been reduced to 3.1 ± 1.8. All other parameters also improved. The treatment was well tolerated. These results point to a safe and effective treatment approach with 5% lidocaine medicated plaster for localized neuropathic pain related to disk herniation. However, owing to the small sample size, further investigation in a larger-scale controlled trial is warranted.

  5. Microscale electrochemical cell using plaster (CaSO4 as liquid junction

    Directory of Open Access Journals (Sweden)

    Yuthapong Udnan

    2008-10-01

    Full Text Available A microscale apparatus for electrochemical cell in which plaster (CaSO4 was used as liquid junction has been developed. A glass tube (0.5 cm ID x 5.0 cm was used to prepare each half-cell. The potentials of the resulting galvanic cells were measured by a multimetre and were compared to those of the galvanic cells in which agar was used as liquid junction. It was found that the potentials produced by the galvanic cells with plaster as liquid junction are not significantly different from those of the cells with agar as liquid junction and close to the theoretical values. In addition, when the developed apparatus was used for the study of electrolysis of potassium iodide solution, it was found that the electrolytic cell made from the microscale apparatus with plaster liquid junction can distinctly separate the reactions occurring at the anode and the cathode. Moreover, the lifetime of the plaster liquid junction is much greater than that of the agar liquid junction.

  6. Clinical Observation on Prevention of Bronchial Asthma with Plaster on Acupoints

    Institute of Scientific and Technical Information of China (English)

    YU Jin-long; ZHU Han-ting

    2008-01-01

    @@ Bronchial asthma is a most common and chronicillness which often relapses and has no cure at present.Acupuncture has its specific advantage in treatingasthma. The author prevented 29 cases of asthma innon-acute stage of attack with plaster on acupoints.Now it is reported as follows.

  7. Forty Cases of Insomnia Treated by Multi-output Electric Pulsation and Auricular Plaster Therapy

    Institute of Scientific and Technical Information of China (English)

    Liu Weizhe

    2007-01-01

    @@ The writer has treated 40 cases of insomnia by the method of multi-output electric pulsation in combination with auricular plaster therapy (with a seed of Vaccariae segetalis 王不留行 taped tightly to a particular ear point and pressed) and received satisfactory therapeutic effects. A report follows.

  8. Bridging the Silos of Service Delivery for High-Need, High-Cost Individuals.

    Science.gov (United States)

    Sherry, Melissa; Wolff, Jennifer L; Ballreich, Jeromie; DuGoff, Eva; Davis, Karen; Anderson, Gerard

    2016-12-01

    Health care reform efforts that emphasize value have increased awareness of the importance of nonmedical factors in achieving better care, better health, and lower costs in the care of high-need, high-cost individuals. Programs that care for socioeconomically disadvantaged, high-need, high-cost individuals have achieved promising results in part by bridging traditional service delivery silos. This study examined 5 innovative community-oriented programs that are successfully coordinating medical and nonmedical services to identify factors that stimulate and sustain community-level collaboration and coordinated care across silos of health care, public health, and social services delivery. The authors constructed a conceptual framework depicting community health systems that highlights 4 foundational factors that facilitate community-oriented collaboration: flexible financing, shared leadership, shared data, and a strong shared vision of commitment toward delivery of person-centered care.

  9. Presión en medios granulares en silos: experimentos para un curso de fluidos

    Directory of Open Access Journals (Sweden)

    Saulo Hernández López

    2015-06-01

    Full Text Available Se presentan las experiencias obtenidas en el análisis del comportamiento estático de un medio granular en un silo. Haciendo uso de un dispositivo experimental construido para tal fin, se explora el comportamiento de la presión ejercida sobre el fondo de un silo cuando sobre él descansa una columna de medio granular (maíz sobrecargado y se compara con el de un líquido. Se utiliza el modelo teórico de Janssen para describir el comportamiento de la presión, obteniendo resultados satisfactorios. Este trabajo podrá servir de base en la elaboración de protocolos de prácticas para los laboratorios de los cursos de física clásica que se imparten en los programas de licenciatura en ciencias e ingeniería.

  10. Packing Bunker and Pile Silos to Minimize Porosity

    Science.gov (United States)

    This article discusses the issue of porosity (i.e., the portion of volume filled with gas) in silages. As porosity increases, the silage is subject to greater losses. Porosity can be reduced by adequately packing the crop at ensiling. To keep porosity below 40% a minimum bulk density of 44 lbs./cu. ...

  11. Factors contributing to the temperature beneath plaster or fiberglass cast material

    Science.gov (United States)

    Hutchinson, Michael J; Hutchinson, Mark R

    2008-01-01

    Background Most cast materials mature and harden via an exothermic reaction. Although rare, thermal injuries secondary to casting can occur. The purpose of this study was to evaluate factors that contribute to the elevated temperature beneath a cast and, more specifically, evaluate the differences of modern casting materials including fiberglass and prefabricated splints. Methods The temperature beneath various types (plaster, fiberglass, and fiberglass splints), brands, and thickness of cast material were measured after they were applied over thermometer which was on the surface of a single diameter and thickness PVC tube. A single layer of cotton stockinette with variable layers and types of cast padding were placed prior to application of the cast. Serial temperature measurements were made as the cast matured and reached peak temperature. Time to peak, duration of peak, and peak temperature were noted. Additional tests included varying the dip water temperature and assessing external insulating factors. Ambient temperature, ambient humidity and dip water freshness were controlled. Results Outcomes revealed that material type, cast thickness, and dip water temperature played key roles regarding the temperature beneath the cast. Faster setting plasters achieved peak temperature quicker and at a higher level than slower setting plasters. Thicker fiberglass and plaster casts led to greater peak temperature levels. Likewise increasing dip-water temperature led to elevated temperatures. The thickness and type of cast padding had less of an effect for all materials. With a definition of thermal injury risk of skin injury being greater than 49 degrees Celsius, we found that thick casts of extra fast setting plaster consistently approached dangerous levels (greater than 49 degrees for an extended period). Indeed a cast of extra-fast setting plaster, 20 layers thick, placed on a pillow during maturation maintained temperatures over 50 degrees of Celsius for over 20

  12. Factors contributing to the temperature beneath plaster or fiberglass cast material

    Directory of Open Access Journals (Sweden)

    Hutchinson Mark R

    2008-02-01

    Full Text Available Abstract Background Most cast materials mature and harden via an exothermic reaction. Although rare, thermal injuries secondary to casting can occur. The purpose of this study was to evaluate factors that contribute to the elevated temperature beneath a cast and, more specifically, evaluate the differences of modern casting materials including fiberglass and prefabricated splints. Methods The temperature beneath various types (plaster, fiberglass, and fiberglass splints, brands, and thickness of cast material were measured after they were applied over thermometer which was on the surface of a single diameter and thickness PVC tube. A single layer of cotton stockinette with variable layers and types of cast padding were placed prior to application of the cast. Serial temperature measurements were made as the cast matured and reached peak temperature. Time to peak, duration of peak, and peak temperature were noted. Additional tests included varying the dip water temperature and assessing external insulating factors. Ambient temperature, ambient humidity and dip water freshness were controlled. Results Outcomes revealed that material type, cast thickness, and dip water temperature played key roles regarding the temperature beneath the cast. Faster setting plasters achieved peak temperature quicker and at a higher level than slower setting plasters. Thicker fiberglass and plaster casts led to greater peak temperature levels. Likewise increasing dip-water temperature led to elevated temperatures. The thickness and type of cast padding had less of an effect for all materials. With a definition of thermal injury risk of skin injury being greater than 49 degrees Celsius, we found that thick casts of extra fast setting plaster consistently approached dangerous levels (greater than 49 degrees for an extended period. Indeed a cast of extra-fast setting plaster, 20 layers thick, placed on a pillow during maturation maintained temperatures over 50 degrees of

  13. Large-scale numerical simulations of polydisperse particle flow in a silo

    Science.gov (United States)

    Rubio-Largo, S. M.; Maza, D.; Hidalgo, R. C.

    2016-09-01

    Very recently, we have examined experimentally and numerically the micro-mechanical details of monodisperse particle flows through an orifice placed at the bottom of a silo (Rubio-Largo et al. in Phys Rev Lett 114:238002, 2015). Our findings disentangled the paradoxical ideas associated to the free-fall arch concept, which has historically served to justify the dependence of the flow rate on the outlet size. In this work, we generalize those findings examining large-scale polydisperse particle flows in silos. In the range of studied apertures, both velocity and density profiles at the aperture are self-similar, and the obtained scaling functions confirm that the relevant scale of the problem is the size of the aperture. Moreover, we find that the contact stress monotonically decreases when the particles approach the exit and vanish at the outlet. The behavior of this magnitude is practically independent of the size of the orifice. However, the total and partial kinetic stress profiles suggest that the outlet size controls the propagation of the velocity fluctuations inside the silo. Examining this magnitude, we conclusively argue that indeed there is a well-defined transition region where the particle flow changes its nature. The general trend of the partial kinetic pressure profiles and the location of the transition region results the same for all particle types. We find that the partial kinetic stress is larger for bigger particles. However, the small particles carry a higher fraction of kinetic stress respect to their concentration, which suggest that the small particles have larger velocity fluctuations than the large ones and showing lower strength of correlation with the global flow. Our outcomes explain why the free-fall arch picture has served to describe the polydisperse flow rate in the discharge of silos.

  14. La vida de Santo Domingo de Silos: onirocrítica y semántica

    Directory of Open Access Journals (Sweden)

    González, Javier Roberto

    2007-12-01

    Full Text Available We study the prophetic vision of Santo Domingo de Silos in Gonzalo de Berceo’s Vida de Santo Domingo de Silos, with the aim of: a analysing the text according to categories of prophecy, vision and dream in medieval christian culture; b analysing the configuration of oniric images as an allegorical discourse; c given the limits of allegorical semantics, interpreting those symbolic images characterized by prophetical obscuritas in the light of Grimaldus’ Vita Beati Dominici, source of Berceo’s Vida, and also in the light of medieval tradition of Other World visions and general chromatic an arithmetical symbolism, in order to establish semantic innovations and the proper meanning of Berceo’s text.Estudiamos la visión profética de Santo Domingo de Silos en la Vida de Santo Domingo de Silos de Gonzalo de Berceo, con el objeto de: a analizar el texto según las categorías de profecía, visión y sueño vigentes en la cultura cristiana medieval; b analizar la configuración de las imágenes oníricas como discurso alegórico; c dados los límites de la semántica alegórica, interpretar aquellas imágenes simbólicas caracterizadas por la obscuritas profética a la luz de la Vita Beati Dominici de Grimaldo, fuente de la Vida de Berceo, y también a la luz de la tradición medieval de las visiones de trasmundo y del simbolismo general cromático y aritmético, en orden al establecimiento de las innovaciones semánticas y con ellas del recto sentido del texto de Berceo.

  15. A differential equation for the flow rate during silo discharge: Beyond the Beverloo rule

    OpenAIRE

    2016-01-01

    We present a differential equation for the flow rate of granular materials during the discharge of a silo. This is based in the energy balance of the variable mass system in contrast with the traditional derivations based on heuristic postulates such as the free fall arch. We show that this new equation is consistent with the well known Beverloo rule, providing an independent estimate for the universal Beverloo prefactor. We also find an analytic expression for the pressure under discharging ...

  16. Mechanics of sequential jamming and unjamming phenomena in a multi-exit orifice silo

    Science.gov (United States)

    Kunte, Amit; Orpe, Ashish; Doshi, Pankaj

    2013-11-01

    We have investigated the flow of a two dimensional granular assembly draining through a flat bottomed silo having multiple exit orifices using DEM simulations. The width of the central orifice of the silo is fixed at 3 . 5 d which is small enough to cause jamming (or no-flow) through the orifice. Here d is the mean particle diameter. The width of the other nearby orifices is kept much more than 3 . 5 d , thus, ensuring continuous flow of particles through them. Interestingly, this continuous flow of particles in the vicinity interacts with the assembly of jammed particles above the central orifice causing rearrangements and ultimately unjamming the assembly leading to a smooth flow. During the entire drainage of the silo, the central orifice undergoes this sequence of jamming-unjamming event several times, the frequency of which depends on its proximity to the nearby orifices. We focus primarily on understanding this jamming-unjamming transition by investigating the contact force network and the normal force distributions. Our preliminary results show that the tails of the force distributions in the jammed region decay slower than those for the flowing regions. This qualitative behaviour is found to be independent of any prior rearrangement history. Department of Science and Technology, India, (Grant No. SR/S3/CE/037/2009).

  17. ECT Image Analysis Methods for Shear Zone Measurements during Silo Discharging Process

    Institute of Scientific and Technical Information of China (English)

    Krzysztof Grudzien; Zbigniew Chaniecki; Andrzej Romanowski; Maciej Niedostatkiewicz; Dominik Sankowski

    2012-01-01

    The paper covers the electrical capacitance tomography(ECT) data analysis on shear zones formed during silo discharging process.This is due to the ECT aptitude for detection of slight changes of material concentration.On the basis of ECT visualisations,wall-adjacent shear zone profiles are analysed for different wall roughness parameters.The analysis on changes of material concentration,based on ECT images,enables the calculation for the characteristic parameters of shear zones-size and material concentration inside the shear zone in a dynamic process of silo discharging.In order to verify the methodology a series of experiments on gravitational flow of bulk solids under various conditions were conducted with different initial granular material packing densities and silo wall roughness.The investigation shows that the increase in container wall roughness is an effective method for reducing the dynamic effects during the material discharging,since these effects are resulted from the resonance between hopper construction and trembling material.Such effects will damage industrial equipment in practical applications and need further investigation.

  18. Experimental study on detection of electrostatic discharges generated by polymer granules inside a metal silo

    Science.gov (United States)

    Choi, Kwangseok; Mogami, Tomofumi; Suzuki, Teruo

    2014-04-01

    To detect electrostatic discharges generated by polymer granules within a metal silo, we developed a novel and simple electrostatic discharge detector that utilizes a photosensor. The novel detector consists of a photosensor module in a metal cylinder, an optical band-pass filter, a quartz glass, a power supply, an amplifier for the photosensor module, and a digital oscilloscope. In this study, we conducted experiments at a real pneumatic powder transport facility that includes a metal silo to evaluate the novel detector using polypropylene granules. To determine the performance of the novel detector, we observed the electrostatic discharge within the metal silo using a conventional image intensifier system. The results obtained from the experiments show that the novel detector worked well in this study. The signals obtained with the novel detector were identical to the electrostatic discharges obtained with the conventional image intensifier system. The greatest advantage of this novel detector is that it is effective even when placed under external lights. In addition, the influence of various optical band-pass filters on the performance of the novel detector was discussed. Our study confirmed that an optical band-pass filter with a center wavelength of λ 330 nm (λ1/2: 315-345 nm) was the best performer among the optical band-pass filters used in this study.

  19. Sound of silo's: An experimental investigation into sound emissions from granular flows in a vertical tube

    Science.gov (United States)

    Porte, Elze; Masen, Marc; Vriend, Nathalie; de Boer, Andre

    2015-11-01

    When large storage silo's containing granular material are discharged, a loud sound emits from the silo. The noise causes disturbances for people working on site and for nearby residential areas. Insufficient knowledge exists to solve the problem efficiently and adequately. An experimental study using a scaled silo setup shows that the particle flow dynamics and system characteristics are both actors in determining the occurrence of the sound and its frequency. The extensive use of frequency analysis provides new insights into the complexity of the related parameters. The particle flow and tube characteristics are manipulated by changing the outflow rate, bulk material, wall material, wall pressure and tube dimensions. Frequency analysis of the recorded sound shows that the frequency depends on both the externally forced parameter changes and internal changes during flow. The latter indicates that during the flow, characteristic properties such as the packing fraction and sound speed change. As a result, the frequency changes as well. However, the external parameters that are manipulated as an initial condition are equally important in describing the frequency response.

  20. Mechanical properties of some granular agricultural materials used in silo design

    Science.gov (United States)

    Moya, M.; Aguado, P. J.; Ayuga, F.

    2013-03-01

    The aim of this research was to provide values for different material properties considered in either traditional or more recent numerical silo design methods. Different samples of granular agricultural materials commonly stored in silos were tested. Common geotechnical devices have been used in order to make the replications easier. Based on these experiments it was determined that the different material properties were not affected by the test velocity, except in the case of Poisson ratio. From a practical point of view, the test velocity correlates well with the sliding velocity of grain during discharge. The values obtained for material properties considered in traditional silo design methods were similar to those reported by other authors. No significant differences were observed in the results obtained when using either the square shear box or the circular shear cell. The same conclusion was reached when comparing the results from direct shear tests with preconsolidated and unconsolidated samples. This means that simplified devices and procedures can be used in agricultural grains against other products. Finally, a table with the recommended values for the different parameters determined for each sample tested was provided in this work.

  1. Cemented backfilling technology with unclassified tailings based on vertical sand silo

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    A new technology characterized by rapidly non-mechanical settlement of unclassified tailings was developed based on a large number of tests,and dynamic settlement and continual slurry preparation without hardening in vertical sand silo were eventually realized by the addition of an effective flocculating agent (NPA).The results show that the sedimentation velocity of interface between unclassified tailings and water after the addition of NPA increases by 10-20 times,the sedimentation mass fraction of unclassified tailings at the bottom of vertical sand silo is up to 64%,the solid particle content of waste water meets the national standard,and the side influences of NPA can be removed by the addition of fly ash.The industrial test result shows that the system,the addition manner and the equipments are rational,and the vertical sand silo is used efficiently.This developed system is simple with large throughput,and the processing cost is 2.2 yuan(RMB)/m3,only 10%-20% of that by mechanical settlement.

  2. Diclofenac epolamine medicated plaster in the treatment of minor soft tissue injuries: a multicenter randomized controlled trial.

    Science.gov (United States)

    Li, Chunde; Frangione, Valeria; Rovati, Stefano; Zheng, Qingshan

    2013-09-01

    To investigate the efficacy and safety of a topical plaster containing diclofenac epolamine (DHEP) 1.3% in the treatment of patients with acute minor soft tissue injuries in China. This prospective, randomized, double blind, placebo-controlled study had balanced random assignment to DHEP medicated plaster and placebo plaster. A total of 384 patients, aged 18-74 years, with minor soft tissue injury occurring within 72 hours of study entry were enrolled and randomized. Plasters were applied twice daily for seven consecutive days. Outcomes were assessed in three visits over 7 days, in addition to patients' daily self-assessment and an adverse events follow-up visit on day 21. The primary efficacy endpoint was the mean change from baseline in pain on movement on a 100 mm Visual Analogue Scale (VAS) after 7 days of treatment. Secondary efficacy endpoints included pain on movement day-by-day evaluation, summed pain intensity difference, overall treatment efficacy, rescue medication consumption, and treatment tolerability. Reduction in pain on movement after 7 days of treatment, the primary efficacy endpoint, was statistically significantly greater in the DHEP plaster group than with placebo (reduction in VAS pain scores -53.78 ± 16.96 vs -37.02 ± 18.30 for DHEP vs placebo, p plaster was evident by day 1 and increased progressively throughout the treatment period. Global pain relief and overall treatment efficacy were significantly better with DHEP. Both DHEP and placebo plaster were well tolerated with few adverse events, mostly application site reactions. A medicated plaster containing DHEP applied to the affected site in Chinese patients with minor soft tissue injury, such as sprains, strains and contusions, was significantly more effective than placebo at reducing pain scores. Onset of action was rapid and the DHEP plaster was safe and well tolerated. The main limitation was the use of a subjective, though validated, self-reported VAS to assess the primary endpoint.

  3. Accuracy and reproducibility of linear measurements of resin, plaster, digital and printed study-models.

    Science.gov (United States)

    Saleh, Waleed K; Ariffin, Emy; Sherriff, Martyn; Bister, Dirk

    2015-01-01

    To compare the accuracy and reproducibility of measurements of on-screen three-dimensional (3D) digital surface models captured by a 3Shape R700™ laser-scanner, with measurements made using a digital caliper on acrylic, plaster models or model replicas. Four sets of typodont models were used. Acrylic models, alginate impressions, plaster models and physical replicas were measured. The 3Shape R700™ laser-scanning device with 3Shape™ software was used for scans and measurements. Linear measurements were recorded for selected landmarks, on each of the physical models and on the 3D digital surface models on ten separate occasions by a single examiner. Comparing measurements taken on the physical models the mean difference of the measurements was 0.32 mm (SD 0.15 mm). For the different methods (physical versus digital) the mean difference was 0.112 mm (SD 0.15 mm). None of the values showed a statistically significant difference (p plaster and acrylic models. The comparison of measurements on the physical models showed no significant difference. The 3Shape R700™ is a reliable device for capturing surface details of models in a digital format. When comparing measurements taken manually and digitally there was no statistically significant difference. The Objet Eden 250™ 3D prints proved to be as accurate as the original acrylic, plaster, or alginate impressions as was shown by the accuracy of the measurements taken. This confirms that using virtual study models can be a reliable method, replacing traditional plaster models.

  4. Use of Ekibastuzsk coal ash as a filler for acid resistant plaster

    Energy Technology Data Exchange (ETDEWEB)

    Korsakov, F.F.; Isichenko, I.I.; Kabanov, G.A.

    1981-01-01

    Acid resistant plasters are used extensively at thermal power plants for protection of gas conduits, ash traps with spouts and hydraulic valves, and the internal surfaces of smoke pump housings. The surface being protected is preliminarily cleaned and a No. 16-20 steel grid attached to the surface by electrial welding. In producing the acid resistant plaster, 14-17 parts by weight of sodium silicofluoride are added to 100 parts by weight of sodium water glass; the remainder consists of andesite or diabase meal to the required consistency. The water glass fulfills the role of a binder; the sodium silicofluoride accelerates solidification of the water glass and the andesite and diabase meal serve as fillers. We found, tested in the laboratory and used successfully (under experimental-industrial conditions) a substitute for andesite and diabase meal. This substitute was ash of Ekibastuzsk coal, which was not only comparable to the meal in regard to quality of the acid resistant plaster, but even exceeded andesite and diabase meal in regard to several qualitative indicators. At the present time, a formula is being developed for an acid resistant plaster produced on the basis of water glass, sodium silicofluoride and ash of Ekibastuzsk coal. In order to verify the possibility of using other ashes instead of andesite and diabase meal, we also tested, under laboratory conditions, acid resistant plasters using ash from thermal power plants (TPP's) also burning Karagandinsk, Kuuchekinsk, Kuznetsk and Kansko-Achinsk coals. In compositions produced with polymer binders, Kansko-Achinsk coal ash was one of the best fillers, providing the most favorable physico-mechanical properties of the composition.

  5. Health economic evidence of 5% lidocaine medicated plaster in post-herpetic neuralgia

    Directory of Open Access Journals (Sweden)

    Liedgens H

    2013-11-01

    Full Text Available Hiltrud Liedgens,1 Marko Obradovic,1 Mark Nuijten2 1Grunenthal GmbH, Aachen, Germany; 2Ars Accessus Medica, Amsterdam, the Netherlands Background: Post-herpetic neuralgia (PHN is the most common and most debilitating complication of herpes zoster, and involves considerable associated costs. Objective: This paper presents results from nine health economic studies undertaken in eight European countries that compared lidocaine medicated plaster with gabapentin and/or pregabalin in PHN. It aims to support the increasing need for published cost-effectiveness data for health care decision-making processes in Europe. Methods: All studies were based on a similar core Markov model with data derived from clinical trials, local Delphi panels, and official national price and tariff lists. The main outcome measure was cost per quality-adjusted life year gained; time without pain or intolerable adverse events was also included as a secondary outcome measure. All studies focused on an elderly population of patients with PHN who had insufficient pain relief with standard analgesics and could not tolerate or had contraindications to tricyclic antidepressants. Results: Despite considerable differences in many of the variables used, the results showed remarkable similarity and suggested that use of lidocaine medicated plaster offered cost-savings in many of the countries studied, where it proved a highly cost-effective alternative to both gabapentin and pregabalin. Conclusion: Lidocaine medicated plaster is a cost-effective alternative to gabapentin and pregabalin in the treatment of PHN. These savings are largely the result of the superior safety profile of the lidocaine medicated plaster. Keywords: post-herpetic neuralgia, zoster, cost-effectiveness, lidocaine, plaster

  6. EVALUATION OF THE THIXOTROPY OF OIL-WELL CEMENTS USED FOR CEMENTING LOST CIRCULATION ZONES: EFFECT OF PLASTER AND BLAST FURNACE SLAG

    Directory of Open Access Journals (Sweden)

    T. Bouziani

    2015-08-01

    Full Text Available Cementing of oil and gas wells can be a very delicate operation. Among the concerns of service companies, during this operation are the nature and conditions of the formations in well. This is the case of cementing operations in southern Algeria, specifically on the fields of In-Amen, where the formations in lost zones are naturally weak and highly permeable. In these areas, drilling fluids (muds and cements pumped will be, completely or partially lost, what we call "lost circulation". Thixotropic cements are useful to overcome lost circulation problems. They are characterized by a special rheological behavior, allowing it to plug lost zones when they are pumped.Our work aims to assess the thixotropy of cements perapred with two types of cement (class G Asland cement and CEM I 42.5 portland cement with the plaster, using a viscometer with coaxial cylinder (couette type. Moreover, the effect of blast furnace slag (LHF on the properties and thixotropic mixtures prepared was also studied. The results show that portland cement (available locally can produce mixes with higher and more stable thixotropy than the class G cement (from importation, which is a practical and economical for cementing job operations in wells with loss zones. The results also show that the effect of LHF is positive, since in addition to his contribution to long term performances, especially the durability of hardened concrete, it improves the thixotropy of cement made of plaster.

  7. Behavior of grains in contact with the wall of a silo during the initial instants of a discharge-driven collapse

    Science.gov (United States)

    Colonnello, C.; Reyes, L. I.; Clément, E.; Gutiérrez, G.

    2014-03-01

    We study experimentally gravity-driven granular discharges of laboratory scale silos, during the initial instants of the discharge. We investigate deformable wall silos around their critical collapse height, as well as rigid wall silos. We propose a criterion to determine a maximum time for the onset of the collapse and find that the onset of collapse always occurs before the grains adjacent to the wall are sliding down. We conclude that the evolution of the static friction towards a state of maximum mobilization plays a crucial role in the collapse of the silo.

  8. Comportamento aerodinâmico e efeito de enrijecimento externo em silos cilíndricos sob a ação do vento Aerodynamic behaviour and external stiffening effect in cylindrical silos under wind action

    Directory of Open Access Journals (Sweden)

    Luciano J. de Andrade Júnior

    2004-12-01

    Full Text Available Os silos metálicos, quando vazios, são suscetíveis ao amassamento das chapas do corpo cilíndrico pela ação do vento. Este trabalho compara os efeitos do enrijecimento interno e externo com colunas, no comportamento aerodinâmico de silos cilíndricos com telhado cônico. Os estudos teóricos conduziram a ensaios em túnel de vento, que foram realizados em dois tipos de modelos reduzidos: um com superfície lisa (enrijecimento interno e o outro com superfície nervurada (enrijecimento externo, ambos em duas relações geométricas de altura/diâmetro do cilindro (0,5 e 1,0 e inclinação da cobertura cônica de 27º. Com base nos ensaios, foram obtidos os coeficientes de pressão externa e os coeficientes de arrasto nos cilindros, bem como os coeficientes de arrasto e de sustentação na cobertura. Com isso, identificou-se o melhor tipo de enrijecimento ao projeto otimizado de silos para resistir adequadamente à ação do vento. O resultado final é um conjunto de dados atualizado, oriundo de ensaios com características de semelhança geométrica e aerodinâmica definidas, que é aplicável a qualquer tipo de silo cilíndrico.Steel cylindrical silos, when empty, are susceptible to the crumpling of the sheeting of the cylinder by the wind action. This paper compares the effects of internal and external stiffening with columns on the aerodynamic behavior of cylindrical silos with conical roof. The theoretical studies leaded to wind tunnel experiments, which have been carried out on two types of scaled silo models, one with smooth surface (internal stiffening, the other with ribbed surface (external stiffening, both with two geometric height/diameter ratio of cylinder (0.5 and 1.0 and a conical roof pitch equal to 27º. Based on the information gained during these experiments, external coefficients of pressure and drag and lift coefficients are derived for the cylinders, as well as the drag and lift coefficients for the conical roofs. With

  9. Archaeomagnetic studies in central Mexico—dating of Mesoamerican lime-plasters

    Science.gov (United States)

    Hueda-Tanabe, Y.; Soler-Arechalde, A. M.; Urrutia-Fucugauchi, J.; Barba, L.; Manzanilla, L.; Rebolledo-Vieyra, M.; Goguitchaichvili, A.

    2004-11-01

    For the first time results of an archaeomagnetic study of unburned lime-plasters from Teotihuacan and Tenochtitlan in central Mesoamerica are presented. Plasters made of lime, lithic clasts and water, appear during the Formative Period and were used for a variety of purposes in floors, sculptures, ceramics and supporting media for mural paintings in the Oaxaca and Maya area. In Central Mexico, grinded volcanic scoria rich in iron minerals is incorporated into the lime-plasters mixture. Samples were selected from two archaeological excavation projects in the Teopancazco residential compound of Teotihuacan and the large multi-stage structure of Templo Mayor in Tenochtitlan, where chronological information is available. The intensity of remanent magnetization (natural remanent magnetization (NRM)) and low-field susceptibility are weak reflecting low relative content of magnetic minerals. NRM directions are well grouped and alternating field demagnetization shows single or two-component magnetizations. Rockmagnetic experiments point to fine-grained titanomagnetites with pseudo-single domain behavior. Anisotropy of magnetic susceptibility (AMS) measurements document a depositional fabric, with normal to free-surface minimum AMS axes. Characteristic mean site directions were correlated to the paleosecular variation curve for Mesoamerica. Data from Templo Mayor reflect recent tilting of the structures. Teopancazco mean site declinations show good correspondence with the reference curve, in agreement with the radiocarbon dating. Dates for four stages of Teotihuacan occupancy based on the study of lime-plasters range from AD 350 to 550. A date for a possible Mazapa occupation around AD 850 or 950 is also suggested based on the archaeomagnetic correlation. The archaeomagnetic record of a plaster floor in Teopancazco differed from the other nearby sites pointing to a thermoremanent magnetization; comparison with the reference curve suggests dates around AD 1375 or 1415. The

  10. In-situ grouting of the low-level radioactive waste disposal silos at ORNL`s Solid Waste Storage Area Six

    Energy Technology Data Exchange (ETDEWEB)

    Francis, C.W.; Farmer, C.D. [Oak Ridge National Lab., TN (US); Stansfield, R.G. [Stansfield (Robert G.), Knoxville, TN (US)

    1993-07-01

    At Oak Ridge National Laboratory (ORNL), one method of solid low-level radioactive waste disposal has been disposed of in below-grade cylindrical concrete silos. Located in Solid Waste Storage Area 6 (SWSA 6), each silo measures 8 ft in diameter and 20 ft deep. Present day operations involve loading the silos with low-level radioactive waste and grouting the remaining void space with a particulate grout of low viscosity. Initial operations involving the disposal of wastes into the below-grade silos did not include the grouting process. Grouting was stated as a standard practice (in late 1988) after discovering that {approximately}75% of the silos accumulated water in the bottom of the silos in the {approximately}2 years after capping. Silo water (leachate) contained a wide range of types and concentrations of radionuclides. The migration of contaminated leachate out of the silo into adjoining soil and groundwater was considered to be a serious environmental concern. This report describes how a specially designed particulate-base grout was used to grout 54 silos previously filled with low-level radioactive waste. Grouting involved three steps: (1) silo preparation, (2) formulation and preparation of the grout mixture, and (3) injection of the grout into the silos. Thirty-five of the 54 silos grouted were equipped with a 3-in.-diam Polyvinyl Chloride (PVC) pipe used to monitor water levels in the silos. A method for rupturing the bottom section of these PVC wells was developed so that grout could be pumped to the bottom of those silos. Holes (2-in. diam) were drilled through the {approximately}18 in. thick concrete to fill the remaining 19 wells without the PVC monitoring wells. The formulation of grout injected into the silos was based on a Portland Type I cement, flyash, sand, and silica fume admixture. Compressive strength of grout delivered to SWSA6 during grouting operations averaged 1,808 lb/in{sup 2} with a bulk density of 3,549 lb/yd{sup 3}.

  11. Batería de silos para la conservación del maíz, Venezuela

    Directory of Open Access Journals (Sweden)

    Guinand & Brillembourg, C. A., Ingenieros

    1966-02-01

    Full Text Available A factory for maize by products has been recently built at Encrucijada de Chivacoa, Yaracuy state. A special feature is the set of reinforced concrete silos, placed in a row. They have been built according to the standard methods normally adopted for this type of structure. It is planned to build finally 16 silos, each with a capacity of 2000 tons. There is a large site available, where ample room has been found for the workshops, services and offices. Both the row of silos and the nearby industrial buildings constitute a modem and attractive architectural feature.Recientemente se ha construido una fábrica de productos derivados del maíz en la Encrucijada de Chivacoa, estado de Yaracuy, en la que destaca la batería de cuatro silos, de hormigón armado, colocados en fila; para su construcción se han seguido los procedimientos tradicionales corrientemente empleados esta clase de obras. Se prevé una ampliación, basta totalizar 16 unidades de 2.000 cada una. Este conjunto industrial dispone de un gran solar, en el que se han colocado las instalaciones anexas, tales como talleres, servicios y oficinas. Tanto la batería de silos propiamente dicha como cada uno de los edificios del conjunto, presentan una línea arquitectónica moderna y agradable.

  12. Análise estrutural de silos metálicos prismáticos Structural analysis of prismatic metallic silos

    OpenAIRE

    José Pinheiro Lopes Neto; José Wallace Barbosa do Nascimento; Carlito Calil Junior

    2008-01-01

    Nos últimos anos, o crescimento da agricultura brasileira tem forçado vários setores a se adequarem aos padrões produtivos com o intuito de se manterem competitivos, frente ao processo de globalização econômica. Nesse contexto, as fábricas de ração avícola tendem a buscar novas alternativas que favoreçam a produção e reduzam custos sem afetar a qualidade do produto final. Entre essas alternativas, destaca-se o uso de silos verticais por facilitar o processo de confecção das rações e eliminar ...

  13. [Experimental study on effects of acupoint application with Leima type II plaster on collagen-induced arthritis in rats].

    Science.gov (United States)

    Li, Peng; Fang, Jian-Qiao; Zhou, Ya-Feng

    2011-09-01

    To observe the therapeutic effect of acupoint application with Leima type II plaster on collagen-induced arthritis (CIA) in rats and probe its mechanism. Bovine type II collagen was injected intradermally into the middle line of the back to induce CIA model with 48 Wistar rats. Then the rats were randomly divided into a model control group (group A), a matrix control group (group B), acupoint application group with plaster of low concentration (group C) and high concentration plaster group (group D), 12 rats in each group. Group C and group D were treated with low and high concentration of Leima type II plaster, and "Shenzhu" (GV 12), "Zhiyang" (GV 9) and "Mingmen" (GV 4) were selected, each application for about 15 hours, once each day for 30 days. Group B was used the same method of acupoint application except using non-drug matrix plaster, and group A was not given any treatment. The morphous and the histopathological changes of affection joint were observed. The paw edema volume after 30 days treatment in group C was significantly lower than that in group B (P plaster has a good therapeutic effect on CIA rats and the protective mechanism is related to the reduction of anti-type II collagen antibody level so as to carry out anti-inflammatory effect and immunosuppression.

  14. Efficacy of betamethasone valerate medicated plaster on painful chronic elbow tendinopathy: a double-blind, randomized, placebo-controlled trial.

    Science.gov (United States)

    Frizziero, Antonio; Causero, Araldo; Bernasconi, Stefano; Papalia, Rocco; Longo, Mario; Sessa, Vincenzo; Sadile, Francesco; Greco, Pasquale; Tarantino, Umberto; Masiero, Stefano; Rovati, Stefano; Frangione, Valeria

    2016-01-01

    to investigate the efficacy and safety of a medicated plaster containing betamethasone valerate (BMV) 2.25 mg in patients with chronic elbow tendinopathy. randomized, double-blind, placebo-controlled study with assignment 2:2:1:1 to BMV medicated plaster applied daily for 12 hours, daily for 24 hours or matched placebo. 62 patients aged ≥18 years with chronic lateral elbow tendinopathy were randomized. The primary efficacy variable was pain reduction (VAS) at day 28. Secondary objectives included summed pain intensity differences (SPID), overall treatment efficacy and tolerability. mean reduction in VAS pain score at day 28 was greater in both BMV medicated plaster groups, -39.35±27.69 mm for BMV12-h and -36.91±32.50 mm for BMV24-h, than with placebo, -20.20±27.32 mm. Considering the adjusted mean decreases, there was a statistically significant difference between BMV12-h and placebo (p=0.0110). Global pain relief (SPID) and overall treatment efficacy were significantly better with BMV. BMV and placebo plasters had similar local tolerability and there were few treatment-related adverse events. BMV plaster was significantly more effective than placebo at reducing pain in patients with chronic elbow tendinopathies. The BMV plaster was safe and well tolerated.

  15. A detailed rock-magnetic and archeomagnetic study of lime-plasters from central Mexico

    Science.gov (United States)

    Soler-Arechalde, A. M.; Rodriguez, M.; Ramirez, O.; Gogichaishvili, A.; Caballero-Miranda, C.; Hueda-Tanabe, Y.; Urrutia-Fucugauchi, J.

    2003-04-01

    We carried out a reconnaissance rock-magnetic and archeomagnetic investigations of lime-plasters at some most important pre-Hispanic sites in Central Mexico. Both burned and unburned lime plasters (in total 30 samples) were analyzed from Teotihuacan, Tlatelolco, Santa Cruz Atizapan and Pañhu. The characteristic directions determined in this study are considered to be of primary origin. Thermomagnetic investigation show that the remanence is carried in most cases by magnetite or Ti-poor titanomagnetite. Unblocking temperature spectra and relatively high coercivity point to 'small' pseudo-single domain magnetic structure grains as responsible for remanent magnetization. Single-component, linear demagnetization plots were observed in most of cases. The mean site directions are consistent with the available reference master curve for Mesoamerica.

  16. Can we save a follow up appointment by leaving nylon sutures under plaster for 6 weeks

    Directory of Open Access Journals (Sweden)

    Randeep Aujla

    2010-02-01

    Full Text Available Randeep Aujla, Abhinav Gulihar, Andrew Chandraraj, Graham TaylorOrthopaedic Department, Glenfield Hospital, Groby Road, Leicester, EnglandBackground: The purpose of this study was to highlight the potential resource saving method of leaving nylon sutures under plaster for 6 weeks after forefoot surgery. Methods: We gathered patient data from 72 cases of forefoot surgery over a 5-year period and analyzed the complications encountered. Only patients who required at least 6 weeks of plaster were included.Results: There were two cases of wound infection and one of flap necrosis. The infection rates are comparable to previous studies into forefoot surgery infection rates. There was no difficulty in removing the sutures and scarring was not noted to be a problem.Conclusions: Financial, convenience and time benefits could be obtained if this technique was in common practice.Keywords: elective forefoot surgery, wound infections, wound complications, nylon sutures

  17. The effects of nicotine in dermal plaster on cognitive functions in patients with Alzheimer's disease.

    Science.gov (United States)

    Snaedal, J; Johannesson, T; Jonsson, J E; Gylfadottir, G

    1996-01-01

    Eighteen patients with probable Alzheimer's disease (NINCDS/ADRDA criteria) participated in a placebo-controlled, double-blind study, with a crossover design. The patients had mild or moderate dementia (MMSE = 20.3 +/- 4.6, range 12-28). The trial consisted of two 4-week periods with a 2-week washout period in between. Nicotine was given in the form of dermal plasters. Most of the patients tolerated the highest doses of 21 mg nicotine/24 h, but some received 14 mg/24 h. The effect was monitored with tests of short-term memory, verbal fluency, attention and psychomotor speed. Nicotine was also determined in the blood. Short-term memory improved significantly after 4 weeks of treatment, both on nicotine and placebo (p nicotine applied in the form of dermal plasters is of any significance in the treatment of memory deficits in patient with Alzheimer's disease.

  18. Can foot compression under a plaster cast prevent deep-vein thrombosis during lower limb immobilisation?

    Science.gov (United States)

    Domeij-Arverud, E; Latifi, A; Labruto, F; Nilsson, G; Ackermann, P W

    2013-09-01

    We hypothesised that adjuvant intermittent pneumatic compression (IPC) beneath a plaster cast would reduce the risk of deep-vein thrombosis (DVT) during post-operative immobilisation of the lower limb. Of 87 patients with acute tendo Achillis (TA) rupture, 26 were prospectively randomised post-operatively after open TA repair. The treatment group (n = 14) received two weeks of IPC of the foot for at least six hours daily under a plaster cast. The control group (n = 12) had no additional treatment. At two weeks post-operatively all patients received an orthosis until follow-up at six weeks. At two and six weeks the incidence of DVT was assessed using colour duplex sonography by two ultrasonographers blinded to the treatment. Two patients withdrew from the study due to inability to tolerate IPC treatment. An interim analysis demonstrated a high incidence of DVT in both the IPC group (9 of 12, 75%) and the controls (6 of 12, 50%) (p = 0.18). No significant differences in incidence were detected at two (p = 0.33) or six weeks (p = 0.08) post-operatively. Malfunction of the IPC leading to a second plaster cast was found to correlate with an increased DVT risk at two weeks (ϕ = 0.71; p = 0.019), leading to a premature abandonment of the study. We cannot recommend adjuvant treatment with foot IPC under a plaster cast for outpatient DVT prevention during post-operative immobilisation, owing to a high incidence of DVT related to malfunctioning of this type of IPC application.

  19. Who should answer the question: "Can I drive with this plaster cast?".

    Science.gov (United States)

    Gandhi, M J; Freitas, D; Lewis, M; Bolton, L; Bhasin, S; Leonard, D; Marsh, A

    2014-02-01

    The application of a plaster cast is known to affect driving ability, but patients continue to drive. The individuals and authorities involved in assessing driving safely include doctors, the Driver and Vehicle Licensing Agency (DVLA), police, insurance companies, and patients, but it is unclear who should take responsibility for the advice given, especially in the event of an accident. We contacted senior plaster technicians in 348 hospitals in the UK. We recorded their responses regarding advice given to patients on driving in specific casts. Sixteen motor insurance companies and 40 police forces were also contacted in order to canvass their opinions. 188 technician interviews (response rate 54%) were conducted. Only 10% of respondents offered advice unprompted; an average of 48% of patients asked for advice. 88% of respondents referred patients to their motor insurance companies, and also to the DVLA (11.7%), doctor (10.6%), or police (5.9%). Only 20.2% of plaster rooms provided written information. All insurance companies would insure patients provided the doctor had not explicitly objected to driving, but there was no consensus amongst the responses received from police. In the event of an accident after the treating doctor had advised against driving, insurance companies were likely to invalidate the policy, and the police would seek penalty punishment or prosecution. Although doctors are not specifically trained to assess the ability of patients to drive, insurance companies and police forces place the responsibility on doctors to advise patients. Since current evidence suggests plaster casts can impair driving ability, we suggest patients should be advised not to drive. Patients accept all responsibility if they continue to drive after receiving this specific advice and understanding its implications. Copyright © 2013 Royal College of Surgeons of Edinburgh (Scottish charity number SC005317) and Royal College of Surgeons in Ireland. Published by Elsevier

  20. Quality of Plaster Molding for Distal Radius Fractures Is Improved Through Focused Tuition of Junior Surgeons.

    Science.gov (United States)

    Ramoutar, Darryl N; Silk, Robert; Rodrigues, Jeremy N; Hatton, Mark

    2014-08-01

    Successful nonoperative management of distal radius fractures requires an adequately reduced fracture held in a well-molded cast. The purpose of this study was to determine whether a targeted teaching session to the same group of junior doctors led to objective improvement in fracture reduction and plaster molding and hence a decrease in the redisplacement of these fractures. Retrospective review. Level I academic trauma center. A retrospective review of all dorsally angulated distal radius fractures treated in plaster that presented to our plaster room over a 4-week period (group 1, n = 52). This was followed by the intervention and a subsequent 4-week prospective review (group 2, n = 36). Radiographs were reviewed before manipulation, after manipulation, and at follow-up by a single senior orthopaedic trainee using predetermined criteria. A targeted teaching session on fracture reduction and cast molding to the same group of junior doctors involved in managing all these cases. Adequate fracture reduction, plaster molding, redisplacement, and further intervention before and after the targeted intervention. In group 1, 85% had adequate fracture reduction but only 36% showed adequate molding. This was improved in group 2%-94% adequate reduction and 65% adequate molding (P = 0.022). The rate of redisplacement was improved from 65% to 44% in group 2. In both groups, the rate of redisplacement was around 20% for adequately reduced and molded fractures, compared with around 90% for adequately reduced but inadequately molded cases (P < 0.001). The rate of further intervention improved from 27% to 8% (P = 0.052). We recommend that specific teaching focusing on fracture reduction and molding techniques is included in orthopaedic juniors' induction teaching or as a separate session. Therapeutic Level III. See Instructions for Authors for a complete description of levels of evidence.

  1. Effect of lipidmicrosphere prostaglandin combined with Shengji plaster on bedsore healing in III and IV degree

    Institute of Scientific and Technical Information of China (English)

    Su-Fang Gao; Qing-Fu Song; Shu-Ping Gao

    2016-01-01

    Objective:To observe the effect of lipidmicrosphere prostaglandin (Lipo PGE1) combined with Shengji plaster on the bedsore healing.Methods: A total of 100 patients with bedsores in III and IV degree who were admitted in our hospital from January, 2013 to January, 2015 were included in the study and divided into the observation group and the control group with 50 cases in each group according to different treatment protocols. The blood glucose, infection, and blood pressure in the two groups were effectively controlled. The patients in the observation group were given intravenous drip of Lipo PGE1 and external application of Shengji plaster, while the patients in the control group were given intravenous drip of Chuanxiongqin injection and external application of Shengji plaster. Four-week treatment was regarded as one course. The specimens on the wound surface of bedsores 1, 2, 3, and 4 weeks after treatment were collected. SABC developing method was used to observe the blood capillary density value (/10 HP). TcPO2 1 cm around the wound surface and the skin temperature were measured.Results:The blood capillary density values 1, 2, 3, and 4 weeks after treatment in the observation group were significantly higher than those in the control group (P<0.05). The bedsore wound surface skin temperature 2, 4, 6, and 8 h after medication in the observation group was significantly lower than that in the control group (P<0.05), while TcPO2 was significantly higher than that in the control group (P<0.05).Conclusions: Lipo PGE1 combined with Shengji plaster can effectively improve the blood circulation on the wound surface of bedsores, and promote the bedsore healing.

  2. Treatment of localized neuropathic pain after disk herniation with 5% lidocaine medicated plaster

    OpenAIRE

    Likar, Rudolf; Kager, Ingo; Obmann,; Pipam, Wolfgang; Sittl,Reinhard

    2012-01-01

    Rudolf Likar,1 Ingo Kager,1 Michael Obmann,1 Wolfgang Pipam,1 Reinhard Sittl21Department of Anesthesiology and Intensive Care, Klagenfurt Hospital, Klagenfurt, Austria; 2Department of Anesthesiology, Interdisciplinary Pain Center, University Hospital Erlangen, Erlangen, GermanyObjective: To assess treatment with the 5% lidocaine medicated plaster for peripheral neuropathic pain after disk herniation.Study design: Case series, single center, retrospective data.Patients and methods: Data of 23 ...

  3. Development of Innovative Aerogel Based Plasters: Preliminary Thermal and Acoustic Performance Evaluation

    Directory of Open Access Journals (Sweden)

    Cinzia Buratti

    2014-09-01

    Full Text Available The thermal and acoustic properties of innovative insulating systems used as building coatings were investigated: Granular silica aerogel was mixed with natural plaster in different percentages. This coating solution is transpiring and insulating, thanks to the use of a natural lime coat and aerogel, a highly porous light material with very low thermal conductivity. The thermal conductivity of the proposed solution was evaluated by means of a Heat Flow meter apparatus (EN ISO 12667, considering different percentages of aerogel. The natural plaster without aerogel has a thermal conductivity of about 0.50 W/m K; considering a percentage of granular aerogel of about 90% in volume, the thermal conductivity of the insulating natural coating falls to 0.050 W/m K. Increasing the percentage of granular aerogel, a value of about 0.018–0.020 W/m K can be reached. The acoustic properties were also evaluated in terms of the acoustic absorption coefficient, measured by means of a Kundt’s Tube (ISO 10534-2. Two samples composed by a plasterboard support, an insulation plaster with aerogel (thicknesses 10 mm and 30 mm respectively and a final coat were assembled. The results showed that the absorption coefficient strongly depends on the final coat, so the aerogel-based plaster layer moderately influences the final value. The application of this innovative solution can be a useful tool for new buildings, but also for the refurbishment of existing ones. This material is in development: until now, the best value of the thermal conductivity obtained from manufacturers is about 0.015 W/m K.

  4. Observations on the Efficacy of Auricular-plaster Therapy plus Medicine in Treating Heroin Addiction

    Institute of Scientific and Technical Information of China (English)

    王泽涛; 袁宜勤; 王军; 罗杰坤

    2006-01-01

    Objective:To investigate the curative effect of auricular-plaster therapy on heroin addiction. Methods: Sixty cases of heroin addiction were treated by auricular-plaster therapy in cooperation with methadone and another 60 cases with methadone as a control. The treatment lasted 10 days. Results and conclusion: The results showed that the curative effect of auricular-plaster therapy plus methadone on heroin addiction was significantly better than that of methadone in the control group(P<0.01). The rate of drug relapse was also significantly lower in the former(P<0.01). It is considered that auricular-plaster therapy in cooperation with methadone is now an ideal therapeutic method for drug withdrawal.%目的:观察耳穴贴压治疗海洛因依赖的疗效.方法:耳穴贴压配合西药美沙酮治疗海洛因依赖60例,并与美沙酮治疗60例作对照,临床戒毒观察10 d.结果与结论:结果表明,耳穴贴压配合西药美沙酮戒毒疗效明显优于对照组美沙酮的戒毒疗效(P《0.01),其复吸率也低(P《0.01).认为耳穴贴压配合西药美沙酮戒毒是目前比较理想的戒毒治疗方法.

  5. Prediction of drilling micro-hole in CO{sub 2} laser irradiated sticking plaster

    Energy Technology Data Exchange (ETDEWEB)

    Rao Zhiming; Lu Yanzhao [Wuhan National Laboratory for Optoelectronic, the College of Optoelectronic Science and Engineering, Huazhong University of Science and Technology, Wuhan 430074, Hubei (China); Wu Tao [School of Science, Wuhan Institute of Technology, Wuhan 430073 (China); Du Jianqiang, E-mail: raozm24@163.com [Depart of Computer Science, Jiangxi University of Traditional Chinese Medicine, Nanchang 330004, Jiangxi (China)

    2011-02-01

    This paper reports a simulation model of drilling micro-hole in sticking plaster heated with a 1064 nm continuous CO{sub 2} laser beam. Laser spot sizes ranged from 0.1 to 0.2mm diameter with axial irradiance power levels of 25-100W. To apply software Ansys, the measured steady-state surface temperature is calculated to rise with both increasing beam power and incident laser irradiance. For temperatures above 450 deg. C, sticking plaster vaporized into ventilation hole, and the size of ventilation hole 0.15mm diameter spent 1.7ms heated with laser power lever of 100W with the size of spot 0.15mm diameter, in good accordance with reported in earlier experiments studies. Similarly, the size of ventilation holes changed with beam power and laser spot diameter. These results show that software Ansys can be used to predict drilling micro-hole in CO{sub 2} laser irradiated sticking plaster and the result of simulation can guide to laser drilling experiments.

  6. Objective assessment of plaster cast quality in pediatric distal forearm fractures: Is there an optimal index?

    Science.gov (United States)

    Labronici, Pedro José; Ferreira, Leonardo Termis; Dos Santos Filho, Fernando Claudino; Pires, Robinson Esteves Santos; Gomes, Davi Coutinho Fonseca Fernandes; da Silva, Luiz Henrique Penteado; Gameiro, Vinicius Schott

    2017-02-01

    Several so-called casting indices are available for objective evaluation of plaster cast quality. The present study sought to investigate four of these indices (gap index, padding index, Canterbury index, and three-point index) as compared to a reference standard (cast index) for evaluation of plaster cast quality after closed reduction of pediatric displaced distal forearm fractures. Forty-three radiographs from patients with displaced distal forearm fractures requiring manipulation were reviewed. Accuracy, sensitivity, specificity, false-positive probability, false-negative probability, positive predictive value, negative predictive value, positive likelihood ratio, and negative likelihood ratio were calculated for each of the tested indices. Comparison among indices revealed diagnostic agreement in only 4.7% of cases. The strongest correlation with the cast index was found for the gap index, with a Spearman correlation coefficient of 0.94. The gap index also displayed the best agreement with the cast index, with both indices yielding the same result in 79.1% of assessments. When seeking to assess plaster cast quality, the cast index and gap index should be calculated; if both indices agree, a decision on quality can be made. If the cast and gap indices disagree, the padding index can be calculated as a tiebreaker, and the decision based on the most frequent of the three results. Calculation of the three-point index and Canterbury index appears unnecessary. Copyright © 2016 Elsevier Ltd. All rights reserved.

  7. Dilatometric studies of plaster sandmix in raw and heat treated state

    Directory of Open Access Journals (Sweden)

    M. Pawlak

    2008-10-01

    Full Text Available Results of dilatometric studies of bounded plaster sandmix applied in precision pressure below atmospheric casting, are presented in this paper. Sandmix composed of half-hydrate α-CaSO4·2H2O with different parts of silica SiO2 was a subject of investigations. Silica is a factor weakening the influence of phase transformations on total distortion of the mould during heating and thus influences the accuracy of prepared cast. Experimental moulders of dimensions 7x35 made of plaster sandmix with silica fraction equal 30; 40; 50; 60 and 70% were used during studies. Sandmix was tested in raw state and after heat treatment changing the α-half hydrate into anhydrite II (CaSO4. It was demonstrated that addition of the silica at level about 50% influences most advantageously on dimension changes of heated sandmix by lowering dilatations 3 times in comparison with sandmix composed of pure α-half hydrate. The transformation of plaster structure into anhydrite II is also important - the shrinkability phase disappears and expansion similar to linear-like appears. It was determined that it is possible to obtain sandmix of small, stabile distortion on the way of appropriate selection of components and heat treatment parameters what improves dimensional and shape accuracy limits of the cast and significantly limits internal stresses in the mould eliminating risk of its cracking.

  8. Does the contact time of alginate with plaster cast influence its properties?

    Directory of Open Access Journals (Sweden)

    Mariana Marquezan

    2012-06-01

    Full Text Available The aim of this study was to verify the influence of the time of contact between alginate and gypsum after the modeling procedure on the properties of the plaster cast, such as surface detail, dimensional stability and microhardness. Thirty cylindrical specimens of orthodontic gypsum Type III were made by means of impressions of a stainless steel master model which had five reference lines in the upper surface. The samples were divided into two groups: Group 1 (G1 - with time of contact of 1 hour; and Group 2 (G2 - 12 hours of contact. All the specimens were stored up to 48 hours until they underwent laboratory testing. Surface detail and dimensional stability were tested by one calibrated examiner using a visual analysis and a profilometer (Profile Projector Nikon model 6C, Nikon Corporation, Tokyo, Japan, respectively, to evaluate the quality of reproduction of the lines and the distances between them. The microhardness was determined for each sample by making six indentations with a Vickers diamond pyramid indenter (Buehler, Lake Bluff, USA under a load of 100 gF for 15 s. The results showed significant difference (P £ 0.05 between groups in two of the three properties examined: surface detail and microhardness, which decreased as the time of contact rose. The 12-hour time of contact between alginate and the plaster cast is not recommended because it influences the quality of the plaster cast.

  9. Does the contact time of alginate with plaster cast influence its properties?

    Directory of Open Access Journals (Sweden)

    Mariana Marquezan

    Full Text Available The aim of this study was to verify the influence of the time of contact between alginate and gypsum after the modeling procedure on the properties of the plaster cast, such as surface detail, dimensional stability and microhardness. Thirty cylindrical specimens of orthodontic gypsum Type III were made by means of impressions of a stainless steel master model which had five reference lines in the upper surface. The samples were divided into two groups: Group 1 (G1 - with time of contact of 1 hour; and Group 2 (G2 - 12 hours of contact. All the specimens were stored up to 48 hours until they underwent laboratory testing. Surface detail and dimensional stability were tested by one calibrated examiner using a visual analysis and a profilometer (Profile Projector Nikon model 6C, Nikon Corporation, Tokyo, Japan, respectively, to evaluate the quality of reproduction of the lines and the distances between them. The microhardness was determined for each sample by making six indentations with a Vickers diamond pyramid indenter (Buehler, Lake Bluff, USA under a load of 100 gF for 15 s. The results showed significant difference (P £ 0.05 between groups in two of the three properties examined: surface detail and microhardness, which decreased as the time of contact rose. The 12-hour time of contact between alginate and the plaster cast is not recommended because it influences the quality of the plaster cast.

  10. Effect of Shengji Yuhong plaster on the wound healing after anal fistula surgery

    Institute of Scientific and Technical Information of China (English)

    Jin-Zhong Liu; Ma Li

    2016-01-01

    Objective:To observe the effect of Shengji Yuhong plaster on the wound healing after anal fistula surgery.Methods:A total of 120 patients with anal fistula who were admitted in our hospital from January, 2011 to December, 2013 for operation were included in the study and randomized into the observation group and the control group with 50 cases in each group after operation. The patients in the observation group were given external application of Shengji Yuhong plaster, while the patients in the control group were given vaselinum ribbon gauze. The patients in the two groups were given 3-week treatment. The wound area, granulation form, healing rate, healing time, and adverse reactions 1, 2, 3 weeks after operation in the two groups were compared.Results:The wound area 1, 2, 4 weeks after operation in the observation group was significantly less than that in the control group (P<0.05). The granulation form score was significantly lower than that in the control group (P<0.05). The wound repairing rate and the total effective rate were significantly higher than those in the control group (P<0.05), and the average healing time was significantly faster than that in the control group (P<0.05). Conclusions:Shengji Yuhong plaster can significantly shorten the wound healing time in patients after anal fistula surgery and is beneficial for the postoperative rehabilitation.

  11. Comparison of virtual and manual tooth setups with digital and plaster models in extraction cases.

    Science.gov (United States)

    Im, Joon; Cha, Jung-Yul; Lee, Kee-Joon; Yu, Hyung-Seog; Hwang, Chung-Ju

    2014-04-01

    The aim of this study was to compare the virtual and manual tooth setups with digital and plaster models in extraction cases by measuring various occlusal parameters and applying the American Board of Orthodontics objective grading system. Linear intra-arch and interarch dimensions (arch width and length, perimeter, overjet, and overbite), angular variables (tip, torque, and rotation), and American Board of Orthodontics objective grading system scores obtained from a digital virtual setup model were compared with those from a plaster model setup. The digital virtual setup model resulted in smaller arch perimeters than did the plaster setup model by 2.20 mm in the maxillary arch (P overjet (P overjet, occlusal contact, and total score (P <0.01) were required for the digital than for the manual setup model. Digital and manual setups lead to similar measurements for intra-arch and interarch occlusal variables. However, because of the possibility of collision on proximal and occlusal contact, delicate adjustments in proximal and occlusal contacts are required. Copyright © 2014 American Association of Orthodontists. Published by Mosby, Inc. All rights reserved.

  12. The potential role of cattail-reinforced clay plaster in sustainable building

    Directory of Open Access Journals (Sweden)

    G. Georgiev

    2014-06-01

    Full Text Available Sustainable development is a key goal in town and country planning, as well as in the building industry. The main aims are to avoid inefficient land use, to improve the energy efficiency of buildings and, thus, to move towards meeting the challenges of climate change. In this article we consider how the use of a traditional low-energy building material, namely clay, might contribute. Recent research has identified a promising connection between the reinforcement of clay for internal wall plastering with fibres from the wetland plant Typha latifolia (cattail and the positive environmental effects of cultivating this species. If large quantities of Typha fibres were to be used in building, the need for cultivation of the plant would increase and create new possibilities for the renaturalisation of polluted or/and degraded peatlands. We explore the topic first on the basis of literature, considering the suitability of Typha for this application and possibilities for its sustainable cultivation, as well as implications for the life cycle analyses of buildings in which it is used. We then report (qualitatively the results of testing different combinations of clay with natural plant (straw and cattail fibres for their suitability as a universal plaster, which demonstrate clearly the superior properties of Typha fibres as a reinforcement material for clay plaster mortars.

  13. Maize Storage in Termite Mound Clay, Concrete, and Steel Silos in the Humid Tropics: Comparison and Effect on Bacterial and Fungal Counts

    Science.gov (United States)

    This study investigated the functional suitability of using the readily-available termite mound clay (TMC) for grain silo construction in comparison to conventional reinforced concrete (RC) and galvanized steel (GS) silos for maize storage in the humid tropics. The extent to which temperature and r...

  14. Discharge of a granular silo as a visco-plastic flow

    Science.gov (United States)

    Staron, L.; Lagrée, P.-Y.; Popinet, S.

    2013-06-01

    Implementing a plastic rheology (using the μ(I)-rheology [5]) in a 2D Navier-Stokes solver, we simulate the continuum counterpart of the granular silo. Doing so, we observe a constant flow rate during the discharge and recover the Beverloo scaling. The results suggest that the constant discharge rate is due to the existence of a friction-dependent yield stress. Discrete simulations are performed using the contact dynamics algorithm. Systematic comparison of the velocity field and the inner deformations shows a good agreement between the two approaches.

  15. Resfriamento artificial para o controle de Coleoptera em arroz armazenado em silo metálico

    Directory of Open Access Journals (Sweden)

    Sonia Maria Noemberg Lazzari

    2006-06-01

    Full Text Available Resfriamento artificial para o controle de Coleoptera em arroz armazenado em silo metálico. O objetivo desta pesquisa foi avaliar o efeito do resfriamento artificial de grãos de arroz para o controle de coleópteros-praga. O ar frio foi insuflado pelo sistema de aeração em um silo metálico com arroz-em-casca. A avaliação do tratamento foi feita quinzenalmente usando armadilhas caladores. As espécies de Coleoptera capturadas foram: Oryzaephilus surinamensis (60%; Cryptolestes ferrugineus (9%; Rhyzopertha dominica (16,5% e Sitophilus spp. (0,5%. Aos 28 dias, a temperatura média da massa de grãos era de 15ºC, e o número médio de insetos havia diminuído 76,8%. A aplicação de ar frio manteve as populações sob controle por aproximadamente 60 dias. Os resultados do monitoramento dos insetos e da temperatura indicaram que um novo ciclo de ar frio deveria ser aplicado nesse período para manter as populações sob controle. Também o manejo adequado da massa de grãos faz-se necessário para garantir resultados satisfatórios do resfriamento artificial.Artificial chilling to control Coleoptera in paddy rice stored in metallic silo. The objective of this research was to evaluate the effect of artificial chilling for the control of coleopterans in stored paddy rice. The cold air was insufflated through the aeration system of a metallic silo with paddy rice. Evaluation of insect number was made every 15 days using probe traps. The species of Coleoptera captured were: Oryzaephilus surinamensis (60%; Cryptolestes ferrugineus (9%; Rhyzopertha dominica (16.5% and Sitophilus spp. (0.5%. By the 28th day the average temperature of the grain mass was 15ºC, and the mean number of insects decreased 76.8%. The cold air application kept the insect populations under control for approximately 60 days. The results of temperature and insect monitoring indicated that a new cycle of cold air should be applied by that time to keep the populations under

  16. A differential equation for the flow rate during silo discharge: Beyond the Beverloo rule

    Directory of Open Access Journals (Sweden)

    Madrid Marcos A.

    2017-01-01

    Full Text Available We present a differential equation for the flow rate of granular materials during the discharge of a silo. This is based in the energy balance of the variable mass system in contrast with the traditional derivations based on heuristic postulates such as the free fall arch. We show that this new equation is consistent with the well known Beverloo rule, providing an independent estimate for the universal Beverloo prefactor. We also find an analytic expression for the pressure under discharging conditions.

  17. Discussion on structure type and structure of rebar concrete silo%钢筋混凝土筒仓的结构选型和构造探讨

    Institute of Scientific and Technical Information of China (English)

    刘瑞军

    2014-01-01

    对钢筋混凝土筒仓的仓上建筑、仓顶、仓壁、仓底、仓下支承结构及基础六部分的选型原则及相应的构造要求进行了论述,以期通过合理的设计,提高结构的安全性及经济性,保证工程设计质量达到规范的要求。%This paper discussed the type selection principle and corresponding structure requirements of building above silo,silo top,silo wall, silo bottom,silo below support structure and foundation six parts,in order to through the reasonably design,improved the safety and economic of structure,ensured the engineering design quality reached the standard requirements.

  18. 18m钢筋混凝土筒仓设计分析%On design for 18 m reinforced concrete silo

    Institute of Scientific and Technical Information of China (English)

    马瑞斌

    2016-01-01

    Combining with the engineering examples,the paper illustrates the design methods for the 18 m reinforced concrete silo from the silo foundation,silo support structure,silo support funnel,and silo wall design,and sums up the precautions in the design process,so as to ensure the structural design to meet the demands of the use.%结合工程实例,从筒仓基础、仓底支承结构、仓底漏斗、仓壁设计等方面,阐述了18 m钢筋混凝土筒仓的设计方法,总结了设计过程中的注意事项,使筒仓的结构设计满足使用要求。

  19. Treatment of allergic rhinitis with acupoint herbal plaster: an oligonucleotide chip analysis.

    Science.gov (United States)

    Shiue, Horng-Sheng; Lee, Yun-Shien; Tsai, Chi-Neu; Chang, Hen-Hong

    2016-11-04

    Allergic rhinitis is regarded as an imbalanced Th1/Th2 cell-mediated response. The present study used microarray analysis to compare gene expression levels between allergic rhinitis patients before and after a series of acupoint herbal plaster applications. In this experimental pilot study, volunteers experiencing sneezing, runny nose, and congestion for more than 9 months in the year following initial diagnoses were included after diagnostic confirmation by otolaryngologists to exclude patients with sinusitis and nasal polyps. Patients with persistent allergic rhinitis each received four acupoint herbal plaster treatments applied using the moxibustion technique. Clinical outcomes were evaluated using the Rhinitis Quality of Life Questionnaire (RQLQ). Peripheral blood samples were analyzed using an ImmunoCAP Phadiatop test, and patients were classified as phadiatop (Ph)-positive or -negative. Microarray results were analyzed for genes that were differentially expressed between (1) Ph-positive and -negative patients treated with herbal plaster; and (2) before and after herbal plaster treatment in the Ph-positive patient group. Unsupervised and supervised methods were used for gene-expression data analysis. Nineteen Ph-positive and four Ph-negative participants with persistent allergic rhinitis were included in the study. RQLQ results indicated that the 19 Ph-positive volunteers experienced improvement in six of seven categories following acupoint herbal plaster treatments, whereas the four Ph-negative participants reported improvement in only two categories. Hierarchical clustering and principle component analysis of the gene expression profiles of Ph-positive and -negative participants indicated the groups exhibited distinct physiological responses to acupoint herbal treatment. Evaluation of gene networks using MetaCore identified that the "Immune response_IL-13 signaling via JAK-STAT" and the "Inflammation_Interferon signaling" were down- and up

  20. 论陈化库设计与设备选择%Design of aging silo and choice of equipment

    Institute of Scientific and Technical Information of China (English)

    秦成峰

    2013-01-01

      重点介绍了陈化库设计需要考虑的因素以及库容量的计算;如何选择陈化设备更合理、更经济,为企业确定陈化方案提供参考。%The design factors of aging silo and the calculation of silo volume, and how to choose the more reasonable aging equipment are described in the paper, which provides the reference for the enterprise to determine the aging scheme.

  1. Design Of The Grain Silo Substation%谈粮食筒库变电所的设计

    Institute of Scientific and Technical Information of China (English)

    王自良; 谢志强

    2012-01-01

    According to the characteristics of the grain silo equipments and the power supply requirements, this article expounded the location and forms for the grain silo substation, in the request of architecture, fire fighting & hvac.professional.%根据粮食筒库的设备特点及供电要求,阐述了筒库变电所的选址、形式以及对建筑、防火、暖通专业的要求。

  2. Silo semiesférico para clinker en Aboño, Asturias (España

    Directory of Open Access Journals (Sweden)

    Quintana Loche, Félix

    1972-09-01

    Full Text Available This semispherical silo for clinker storage was built by the construction firm Huarte and Co., in the cement factory at Abono, Asturias. Designed under the supervision of the Technical Services of Ciment Lafarge of Paris, by Enterprise René Marion and Structures Davidaff, it constitutes a world innovation among clinker storage systems. The great heterogeneity of the quarries required the study and use of new means of sampling and statistical dosification, thus producing cement of exceptional evenness. The semispherical storage silo is destined to contain a clinker stock of 35,000 tons; feed and collection are done by means of rotary systems that revolve around a ve/tical axis in the centre of the silo. This feature determined the shape of the silo — a spherical dome, 63.50 m in diameter, of which the centre is situated 5 m below the ground. The design adopted required the use of prefabrication, and is a world innovation in its function, form and building procedure.El silo semiesférico para almacenamiento de clinker ha sido construido por la Empresa Constructora Huarte y Cia., en la Fábrica de Cementos del Cantábrico de Abono (Asturias. El proyecto, elaborado bajo la supervisión de los Servicios Técnicos de Ciments Lafarge de París, y por la Entreprise René Marion y Structures Oavidaff, constituye una novedad mundial dentro de los sistemas de almacenamiento de clinker. La gran heterogeneidad de las canteras ha exigido el estudio y la utilización de nuevos medios de muestreo y dosificación estadística, permitiendo fabricar un cemento de una regularidad excepcional. El silo de almacenamiento semiesférico está destinado a contener un stock de clinker de 35.000 t; la alimentación y recogida se hacen por medio de sistemas rotativos que giran alrededor de un eje vertical que pasa por el centro del silo. Esta característica ha determinado naturalmente la forma del silo: una cúpula esférica, de 63,50 m de diámetro, cuyo centro se

  3. ELEMENTOS PRÉ-MOLDADOS DE CONCRETO ARMADO, PARA SILOS QUADRADOS VERTICAIS, MODULARES, PARA ARMAZENAMENTO DE GRÃOS

    OpenAIRE

    Eduardo Teixeira da Silva; Wesley Jorge Freire; Carlito Calil Júnior

    1998-01-01

    RESUMO Este trabalho foi desenvolvido com o objetivo de fornecer subsídios técnicos para projetos de silos multicelulares em concreto armado, pré-moldados, com forma quadrada, para atender a pequenos e médios produtores, com capacidade de 60t, sendo 15t de milho por célula. Foram realizadas análises teóricas e experimentais em um modelo de elemento construtivo a fim de se avaliar o comportamento estrutural do elemento isolado e do encaixado, em escala natural, que formaram as paredes de silos...

  4. Estimates of inhalation doses resulting from the possible use of phospho-gypsum plaster-board in Australian homes.

    Science.gov (United States)

    O'Brien, R S; Peggie, J R; Leith, I S

    1995-04-01

    Current materials used as internal lining in Australian buildings are based on natural gypsum of low radium content. A study was carried out to estimate the contribution to the annual effective dose due to airborne contamination from chemical by-product gypsum plaster-board of higher radium content if it were used as an internal lining. The 226Ra content and 222Rn exhalation rate were measured for several samples of the plaster-board, and the behavior of 222Rn and its progeny (218Po, 214Pb, 214Bi, and 214Po) in a typical building was modeled numerically, using the results of the exhalation rate measurements as input. For building ventilation rates greater than approximately 0.5 air changes per hour, the contribution to the total annual effective dose from inhalation of 222Rn and its progeny exhaled from the phospho-gypsum plaster-board is estimated to be below 1 mSv. This contribution is reduced if the surface of the plaster-board is coated with paint or cardboard, or if the very fine particles are removed from the phospho-gypsum during manufacture of the plaster-board. The effective doses arising from dust generation during the installation of the plaster-board are also estimated to be below 1 mSv. The recommended action level of 200 Bq m-3 for radon in air in Australia corresponds to an annual effective dose of approximately 6 mSv. The study indicates that the suggested acceptable level of 185 Bq kg-1 for the 226Ra concentration in the plaster-board may be too restrictive under Australian conditions.

  5. Diclofenac epolamine plus heparin plaster versus diclofenac epolamine plaster in mild to moderate ankle sprain: a randomized, double-blind, parallel-group, placebo-controlled, multicentre, phase III trial.

    Science.gov (United States)

    Costantino, Cosimo; Kwarecki, Jacek; Samokhin, Anatoly V; Mautone, Giuseppe; Rovati, Stefano

    2011-01-01

    In general sports, ankle sprain is the most frequently reported ankle injury and can cause chronic lateral ankle pain and tenderness. Treatment with NSAIDs is preferred, and several topical NSAID formulations are now available, helping to avoid the systemic adverse events typically associated with oral preparations. To compare the efficacy and tolerability of a newly developed fixed-dose diclofenac epolamine (diclofenac hydroxyethylpyrrolidine, DHEP)/heparin plaster (Flectoparin® Tissugel) with that of a DHEP (Flector EP Tissugel®) or placebo plaster in the treatment of mild to moderate ankle sprain in adults. This was a randomized, double-blind, parallel-group, placebo-controlled, multicentre, phase III study conducted in the emergency medical centres of hospitals or private clinics in Europe. Outpatients aged 18-65 years who had suffered an acute ankle sprain (O'Donoghue grade I or II in severity, with external lateral ligament involvement) within the previous 48 hours and had peri-malleolar oedema were eligible for inclusion. A total of 430 patients were randomized to receive a DHEP/heparin 1.3%/5600 IU (n = 142), DHEP 1.3% (n = 146) or placebo (n = 142) plaster, applied once daily to the injured ankle for a total of 7 days. The primary endpoint was the mean change from baseline in pain on movement on day 3, as measured by a visual analogue scale (VAS). The DHEP/heparin plaster was associated with a significantly (p = 0.002) greater mean reduction from baseline in pain on movement after 3 days of treatment than the DHEP plaster (-24.2 vs -18.8 mm VAS), with each active treatment providing significantly (p ≤ 0.005) greater pain relief than placebo (-13.7 mm VAS). Both DHEP/heparin and DHEP were also effective in relieving other measures of pain, with DHEP/heparin recipients experiencing significantly less daily pain while leaning on the injured limb than DHEP recipients (p plaster and DHEP plaster were both well tolerated, with

  6. Stress profile in a two-dimensional silo: Effects induced by friction mobilization

    Science.gov (United States)

    Vivanco, Francisco; Mercado, José; Santibáñez, Francisco; Melo, Francisco

    2016-08-01

    The effects of friction mobilization on the stress profile within a two-dimensional silo are investigated via simulations of discrete elements. Friction mobilization is driven by cyclic vertical displacement of the sidewalls. Two regimes have been observed for small filling height, with stress profiles identified as saturated (Janssen's profile) and exponentially growing. The transition between these regimes is denoted by an almost linear stress profile, similar to that of a hydrostatic system, with a significantly greater characteristic height compared to the height of the column of grains. For tall columns, the process of friction inversion is more complex. A partial inversion of friction mobilization is observed when the motion is reversed from upward to downward, which results in two coexisting zones of opposite mobilization. These zones are separated by a wide compaction front with a gradual upward progression sustained by the displacement of the walls. Conversely, if the motion is reversed, the two opposing friction mobilization zones retract, the transition zone becomes smooth, and the system rapidly transforms from two coexisting mobilization states to a Janssen-like regime. In both regimes, the general characteristics from the resulting stress profiles are depicted by generalizing Janssen's equation to include partial mobilization through the varying effective friction coefficient along the silo walls.

  7. Surface depression with double-angle geometry during the discharge of grains from a silo

    Science.gov (United States)

    Pacheco-Vázquez, F.; Ramos-Reyes, A. Y.; Hidalgo-Caballero, S.

    2017-08-01

    When rough grains in loose packing conditions are discharged from a silo, a conical depression with a single slope is formed at the surface. We observed that the increase of volume fraction generates a more complex depression, characterized by two angles of discharge: one at the bottom similar to the angle of repose and a considerably larger upper angle. The change in slope appears at the boundary between a dense stagnant region at the periphery and the central flowing channel formed over the aperture. Since the material in the latter zone is always fluidized, the flow rate is unaffected by the initial packing of the bed. On the other hand, the contrast between both angles is markedly smaller when smooth particles of the same size and density are used, which reveals that high packing fraction and friction must combine to produce the observed geometry. Our results show that the surface profile helps to identify by simple visual inspection the packing conditions of a granular bed, being useful to prevent undesirable collapses during silo discharge in industry.

  8. Stress profile in a two-dimensional silo: Effects induced by friction mobilization.

    Science.gov (United States)

    Vivanco, Francisco; Mercado, José; Santibáñez, Francisco; Melo, Francisco

    2016-08-01

    The effects of friction mobilization on the stress profile within a two-dimensional silo are investigated via simulations of discrete elements. Friction mobilization is driven by cyclic vertical displacement of the sidewalls. Two regimes have been observed for small filling height, with stress profiles identified as saturated (Janssen's profile) and exponentially growing. The transition between these regimes is denoted by an almost linear stress profile, similar to that of a hydrostatic system, with a significantly greater characteristic height compared to the height of the column of grains. For tall columns, the process of friction inversion is more complex. A partial inversion of friction mobilization is observed when the motion is reversed from upward to downward, which results in two coexisting zones of opposite mobilization. These zones are separated by a wide compaction front with a gradual upward progression sustained by the displacement of the walls. Conversely, if the motion is reversed, the two opposing friction mobilization zones retract, the transition zone becomes smooth, and the system rapidly transforms from two coexisting mobilization states to a Janssen-like regime. In both regimes, the general characteristics from the resulting stress profiles are depicted by generalizing Janssen's equation to include partial mobilization through the varying effective friction coefficient along the silo walls.

  9. Curative effect of Tai Chi exercise in combination with auricular plaster therapy on improving obesity patient with secondary hyperlipidemia.

    Science.gov (United States)

    Song, Qinghua; Yuan, Yandong; Jiao, Chun; Zhu, Ximei

    2015-01-01

    Observe the effect of Tai Chi in combination with auricular plaster therapy on treating obesity patient with secondary hyperlipidemia. Select 45 patients who suffer from simple obesity and secondary hyperlipidemia and then adopt random digital table to divide them into a Tai Chi group, an auricular plaster therapy group and a combination group. Each group consists of 15 patients. The patients in Tai Chi group are trained with Tai Chi twice a day, while those in auricular plaster therapy are treated with auricular plaster therapy 3-5 times a day and those in the combination group are trained with Tai Chi and auricular plaster therapy twice a day. BMI, body fat percentage and blood lipid indexes are respectively detected for the selected patients in the three groups before treatment and after 180 days' treatment. After 180 days' treatment, BMI index and body fat percentage of Tai Chi group are significantly improved in comparison with those before treatment (Pplaster therapy group are not improved obviously in comparison with those before the treatment (P>0.05) but the blood lipid index is improved significantly (Pplaster therapy can show the obvious synergistic therapeutic effect and thus the combined curative effect is obviously superior to that of the single therapy method.

  10. Can treatment success with 5% lidocaine medicated plaster be predicted in cancer pain with neuropathic components or trigeminal neuropathic pain?

    Science.gov (United States)

    Kern, Kai-Uwe; Nalamachu, Srinivas; Brasseur, Louis; Zakrzewska, Joanna M

    2013-01-01

    An expert group of 40 pain specialists from 16 countries performed a first assessment of the value of predictors for treatment success with 5% lidocaine-medicated plaster in the management of cancer pain with neuropathic components and trigeminal neuropathic pain. Results were based on the retrospective analysis of 68 case reports (sent in by participants in the 4 weeks prior to the conference) and the practical experience of the experts. Lidocaine plaster treatment was mostly successful for surgery or chemotherapy-related cancer pain with neuropathic components. A dose reduction of systemic pain treatment was observed in at least 50% of all cancer pain patients using the plaster as adjunct treatment; the presence of allodynia, hyperalgesia or pain quality provided a potential but not definitively clear indication of treatment success. In trigeminal neuropathic pain, continuous pain, severe allodynia, hyperalgesia, or postherpetic neuralgia or trauma as the cause of orofacial neuropathic pain were perceived as potential predictors of treatment success with lidocaine plaster. In conclusion, these findings provide a first assessment of the likelihood of treatment benefits with 5% lidocaine-medicated plaster in the management of cancer pain with neuropathic components and trigeminal neuropathic pain and support conducting large, well-designed multicenter studies.

  11. Functional exercise in combination with auricular plaster therapy is more conducive to rehabilitation of menopausal women patients with anxiety disorder.

    Science.gov (United States)

    Han, Yubin; Duan, Fugui; Xu, Rongmei; Wang, Yi; Zhang, Hongyu

    2015-01-01

    Observe the effect of functional exercise in combination with auricular plaster therapy on menopausal women patients with anxiety disorder. Select 45 menopausal women patients with anxiety disorder and then adopt random digital table to divide them into a functional exercise group, an auricular plaster therapy group and a combination group. Each group consists of 15 patients. The patients in the functional exercise group do yoga exercise twice a day; those in the auricular plaster therapy group are provided with the auricular plaster therapy twice a day; those in the combination group do yoga exercise and then they are provided with the auricular plaster therapy twice a day. Before the treatment and after 12 weeks' treatment, respectively detect and compare the selected patients in the three groups in respect HAMA score, physical function score and mental function score; And the cured patients are followed up for 3 months to compare recurrence rate of each group. After 12 weeks' treatment, HAMA score, physical function score and mental function score of the combination group are obviously better than those of another two groups (Pplaster, the combined curative effect is obviously better than that of single treatment and the clinical recurrence rate is significantly lower than that of single treatment. It shows that the combined treatment method presents obvious synergistic effect and the synergistic treatment is more beneficial to improve the curative effect.

  12. 5% Lidocaine Medicated Plaster for the Treatment of Postherpetic Neuralgia: A Review of the Clinical Safety and Tolerability.

    Science.gov (United States)

    Navez, Marie Louise; Monella, Christopher; Bösl, Irmgard; Sommer, Daniela; Delorme, Claire

    2015-06-01

    Postherpetic neuralgia (PHN) is a common, very painful, and often long-lasting complication of herpes zoster which is frequently underdiagnosed and undertreated. It mainly affects the elderly, many of whom are already treated for comorbidities with a variety of systemic medications and are thus at high risk of drug-drug interactions. An efficacious and safe treatment with a low interaction potential is therefore of high importance. This review focuses on the safety and tolerability of the 5% lidocaine medicated plaster, a topical analgesic indicated for the treatment of PHN. The available literature (up to June 2014) was searched for publications containing safety data regarding the use of the 5% lidocaine medicated plaster in PHN treatment; unpublished clinical safety data were also included in this review. The 5% lidocaine medicated plaster demonstrated good short- and long-term tolerability with low systemic uptake (3 ± 2%) and minimal risk for systemic adverse drug reactions (ADRs). ADRs related to topical lidocaine treatment were mainly application site reactions of mild to moderate intensity. The treatment discontinuation rate was generally below 5% of patients. In one trial, the 5% lidocaine medicated plaster was better tolerated than systemic treatment with pregabalin. The 5% lidocaine medicated plaster provides a safe alternative to systemic medications for PHN treatment, including long-term pain treatment.

  13. Can treatment success with 5% lidocaine medicated plaster be predicted in cancer pain with neuropathic components or trigeminal neuropathic pain?

    Science.gov (United States)

    Kern, Kai-Uwe; Nalamachu, Srinivas; Brasseur, Louis; Zakrzewska, Joanna M

    2013-01-01

    An expert group of 40 pain specialists from 16 countries performed a first assessment of the value of predictors for treatment success with 5% lidocaine-medicated plaster in the management of cancer pain with neuropathic components and trigeminal neuropathic pain. Results were based on the retrospective analysis of 68 case reports (sent in by participants in the 4 weeks prior to the conference) and the practical experience of the experts. Lidocaine plaster treatment was mostly successful for surgery or chemotherapy-related cancer pain with neuropathic components. A dose reduction of systemic pain treatment was observed in at least 50% of all cancer pain patients using the plaster as adjunct treatment; the presence of allodynia, hyperalgesia or pain quality provided a potential but not definitively clear indication of treatment success. In trigeminal neuropathic pain, continuous pain, severe allodynia, hyperalgesia, or postherpetic neuralgia or trauma as the cause of orofacial neuropathic pain were perceived as potential predictors of treatment success with lidocaine plaster. In conclusion, these findings provide a first assessment of the likelihood of treatment benefits with 5% lidocaine-medicated plaster in the management of cancer pain with neuropathic components and trigeminal neuropathic pain and support conducting large, well-designed multicenter studies. PMID:23630431

  14. Developing a Penetrometer-Based Mapping System for Visualizing Silage Bulk Density from the Bunker Silo Face.

    Science.gov (United States)

    Li, Menghua; Jungbluth, Kerstin H; Sun, Yurui; Cheng, Qiang; Maack, Christian; Buescher, Wolfgang; Lin, Jianhui; Zhou, Haiyang; Wang, Zhongyi

    2016-07-05

    For silage production, high bulk density (BD) is critical to minimize aerobic deterioration facilitated by oxygen intrusion. To precisely assess packing quality for bunker silos, there is a desire to visualize the BD distribution within the silage. In this study, a penetrometer-based mapping system was developed. The data processing included filtering of the penetration friction component (PFC) out of the penetration resistance (PR), transfer of the corrected penetration resistance (PRc) to BD, incorporation of Kriged interpolation for data expansion and map generation. The experiment was conducted in a maize bunker silo (width: 8 m, middle height: 3 m). The BD distributions near the bunker silo face were represented using two map groups, one related to horizontal- and the other to vertical-density distribution patterns. We also presented a comparison between the map-based BD results and core sampling data. Agreement between the two measurement approaches (RMSE = 19.175 kg·m(-3)) demonstrates that the developed penetrometer mapping system may be beneficial for rapid assessment of aerobic deterioration potential in bunker silos.

  15. 粉矿仓结构设计探讨%Probing into the Structural Design of Fine Ore Silo

    Institute of Scientific and Technical Information of China (English)

    黄明; 赵广强

    2014-01-01

    粉矿仓作为一种短期贮存生产散料的工业构筑物,仓顶进料,仓底卸料,经常用于冶金工业中。其结构形式不同于一般的梁板结构,又被称为特种结构,其设计和计算都比较复杂。文章结合工程实例,介绍了粉矿仓设计中涉及的问题,特别是9度区的注意问题,对以后相关的设计给以借鉴。%Fine ore silo as a short-term storage of bulk production of industrial structure, the silo top feed and the silo bottom discharge are often used in the metallurgical industry. Its structure is different from the beam slab structure, also known as the special structure, and its design and calculation are complex. Combined with engineering practice, this paper describes the problems involved in the design of fine ore silo, especially pays attention to the problem of 9 degree zone, providing references for the related design.

  16. Developing a Penetrometer-Based Mapping System for Visualizing Silage Bulk Density from the Bunker Silo Face

    Directory of Open Access Journals (Sweden)

    Menghua Li

    2016-07-01

    Full Text Available For silage production, high bulk density (BD is critical to minimize aerobic deterioration facilitated by oxygen intrusion. To precisely assess packing quality for bunker silos, there is a desire to visualize the BD distribution within the silage. In this study, a penetrometer-based mapping system was developed. The data processing included filtering of the penetration friction component (PFC out of the penetration resistance (PR, transfer of the corrected penetration resistance (PRc to BD, incorporation of Kriged interpolation for data expansion and map generation. The experiment was conducted in a maize bunker silo (width: 8 m, middle height: 3 m. The BD distributions near the bunker silo face were represented using two map groups, one related to horizontal- and the other to vertical-density distribution patterns. We also presented a comparison between the map-based BD results and core sampling data. Agreement between the two measurement approaches (RMSE = 19.175 kg·m−3 demonstrates that the developed penetrometer mapping system may be beneficial for rapid assessment of aerobic deterioration potential in bunker silos.

  17. Developing a Penetrometer-Based Mapping System for Visualizing Silage Bulk Density from the Bunker Silo Face

    Science.gov (United States)

    Li, Menghua; Jungbluth, Kerstin H.; Sun, Yurui; Cheng, Qiang; Maack, Christian; Buescher, Wolfgang; Lin, Jianhui; Zhou, Haiyang; Wang, Zhongyi

    2016-01-01

    For silage production, high bulk density (BD) is critical to minimize aerobic deterioration facilitated by oxygen intrusion. To precisely assess packing quality for bunker silos, there is a desire to visualize the BD distribution within the silage. In this study, a penetrometer-based mapping system was developed. The data processing included filtering of the penetration friction component (PFC) out of the penetration resistance (PR), transfer of the corrected penetration resistance (PRc) to BD, incorporation of Kriged interpolation for data expansion and map generation. The experiment was conducted in a maize bunker silo (width: 8 m, middle height: 3 m). The BD distributions near the bunker silo face were represented using two map groups, one related to horizontal- and the other to vertical-density distribution patterns. We also presented a comparison between the map-based BD results and core sampling data. Agreement between the two measurement approaches (RMSE = 19.175 kg·m−3) demonstrates that the developed penetrometer mapping system may be beneficial for rapid assessment of aerobic deterioration potential in bunker silos. PMID:27399703

  18. Reasons analysis and measures for PTA large storage silo deformation%PTA大料仓变形的原因及措施

    Institute of Scientific and Technical Information of China (English)

    鲍建明; 任兰英

    2015-01-01

    介绍了PTA大料仓结构,合纤公司及洛阳分公司下料、送料方式,分析了聚酯装置3台PTA大料仓变形的原因。A,B料仓变形原因为PTA架桥,大料仓氮气补充设备故障,料仓顶部呼吸阀不动作或动作不及时,C料仓变形原因是PTA架桥。对A,B和C料仓分别采取相应的措施。%The structure of PTA large storage silo,the feeding and conveying way of synthetic fiber comPany and Luoyang Petrochemical ComPany was introduced. The deformation reasons for the three PTA large storage silo of PET Plant were analysed. The deformation reasons for A,B storage silo were PTA bridging,large storage silo nitrogen suPPlement facility failure,the breathing valve on toP of the storage silo not action or action not timely. The deforma﹣tion reason for C storage silo was PTA bridging. APProPriate measures were taken for A,B and C storage silo.

  19. Study of plaster finishes on San Pedro de los Francos church at Calatayud

    Directory of Open Access Journals (Sweden)

    Sánchez de Rojas, Mª I

    2007-06-01

    Full Text Available This study of the plaster finishes on San Pedro de los Francos Church at Calatayud revealed, firstly, the stratigraphic sequence based on the interpretation of the bonding interfaces; and secondly, the evolution of placement techniques from mudéjar style textured and painted false stonework (15th century to the smooth plastering and paint typical of later phases. Finally, scanning electron microscope (SEM, energy dispersive X-ray microanalysis (EDX and X-ray diffraction (XRD studies showed that gypsum and anhydrite are the main components of both binder and aggregate in these mortars. In other words, they constitute traditional multiphase plasters whose coarser particles or aggregate were a byproduct of the artisanal manufacturing process.El estudio de los enlucidos de la iglesia de San Pedro de los Francos de Calatayud ha permitido demostrar, en primer lugar, la secuencia estratigráfica mediante la lectura de la interfase de adherencia; en segundo lugar, la evolución de las técnicas de aplicación, desde el enlucido mudéjar, un fingido de piedra agramilado y pintado (siglo XV, hasta los enlucidos lisos y pinturas aplicados posteriormente. Y, finalmente, a través de los estudios de microscopía electrónica de barrido (SEM, microanálisis por energía dispersiva de rayos X (EDX y de difracción de rayos X (DRX, se ha determinado que son morteros en los que tanto el conglomerante como el árido son yeso y anhidrita, que correspondería a un yeso tradicional multifase, cuyos granos más gruesos analizados como áridos proceden del producto obtenido artesanalmente.

  20. 5% lidocaine medicated plaster double effect in a case of orofacial localized neuropathic pain

    Directory of Open Access Journals (Sweden)

    Casale R

    2014-11-01

    Full Text Available Roberto Casale,1,2 Yuriy Romanenko,2,3 Massimo Allegri4–6 1Department of Clinical Neurophysiology and Pain Rehabilitation Unit, Foundation "Salvatore Maugeri", Research and Care Institute, IRCCS, Pavia, Italy; 2EFIC Montescano Pain School, Montescano, Italy; 3Department of Neurology, Lugansk City Hospital 4, Lugansk, Ukraine; 4Department of Clinical, Surgical, Diagnostic and Pediatric Sciences University of Pavia, Pavia, Italy; 5Pain Therapy Service Fondazione IRCCS Policlinico San Matteo, Pavia, Italy; 6SIMPAR group, Pavia, Italy Abstract: Localized neuropathic pain (LNP is a type of neuropathic pain that is characterized by “consistent and limited area(s of maximum pain associated with negative or positive sensory signs and/or spontaneous symptoms characteristic of neuropathic pain”. This definition encompasses a huge number of neuropathic orofacial pain syndromes. We present a case report of a patient who was affected with sleep apnea syndrome treated with nocturnal oxygen mask delivery, in whom orofacial LNP hampered the wearing of a mask due to unbearable burning and throbbing pain. The application of 5% lidocaine medicated plaster during the night led to an impressive reduction of both the pain level and the size of the painful area due to the plaster's pharmacological mechanisms, which were associated with a secondary benefit due to its mechanical protective action. This case report shows how these two factors could be of clinical value and have to be considered more systematically in the treatment of LNP in reducing pain and the size of the painful area. Keywords: trigeminal pain, localized neuropathic pain, topical treatment, 5% lidocaine medicated plaster

  1. [Efficacy on borderline hypertension treated with acupuncture combined with anti-hypertensive plaster intervention].

    Science.gov (United States)

    Li, Yan-mei

    2014-11-01

    To compare the efficacy difference in treatment of borderline hypertension between acupuncture combined with anti-hypertensive plaster and simple acupuncture. Sixty patients of borderline hypertension were randomized into an observation group and a control group, 30 cases in each one. In the observation group, acupuncture was applied to Fengchi (GB 20), Taichong (LR 3) and the others, once a day, 5 treatments made one session. There were 2 days at interval among the sessions. Totally, 4 sessions were required. Additionally, in combination, the anti-hypertensive plaster was prepared with the fine powder of Chuanxiong (ligusticum wallichii) and Wuzhuyu (fructus evodiae) at 1.1 and mixed with vinegar. The plaster was applied to the umbilicus, once every two days, totally 15 times were required. In the control group, acupuncture was given simply. The selected acupoints and operation were the same as the observation group. Before and after treatment, blood pressure and syndrome score were observed and the short-term and long-term efficacies were assessed in the two groups. After treatment, the systolic pressure and diastolic pressure were reduced as compared with those before treatment in the two groups (all P0.05). In follow-up of the effective cases and remarkably effective cases in 3 months, the total effective rate in the observation group was 89.3% (25/28) and was 60.0% (15/25) in the control group, indicating the significant difference in comparison (Pplaster is the effective method in prevention and treatment of borderline hypertension. Regarding the long-term efficacy, this combined therapy achieves the superior improvement in the symptoms and physical signs of the patients of borderline hypertension as compared with simple acupuncture.

  2. Comparative study of dental arch width in plaster models, photocopies and digitized images

    Directory of Open Access Journals (Sweden)

    Maria Cristina Rosseto

    2009-06-01

    Full Text Available The aim of this study was to comparatively assess dental arch width, in the canine and molar regions, by means of direct measurements from plaster models, photocopies and digitized images of the models. The sample consisted of 130 pairs of plaster models, photocopies and digitized images of the models of white patients (n = 65, both genders, with Class I and Class II Division 1 malocclusions, treated by standard Edgewise mechanics and extraction of the four first premolars. Maxillary and mandibular intercanine and intermolar widths were measured by a calibrated examiner, prior to and after orthodontic treatment, using the three modes of reproduction of the dental arches. Dispersion of the data relative to pre- and posttreatment intra-arch linear measurements (mm was represented as box plots. The three measuring methods were compared by one-way ANOVA for repeated measurements (α = 0.05. Initial / final mean values varied as follows: 33.94 to 34.29 mm / 34.49 to 34.66 mm (maxillary intercanine width; 26.23 to 26.26 mm / 26.77 to 26.84 mm (mandibular intercanine width; 49.55 to 49.66 mm / 47.28 to 47.45 mm (maxillary intermolar width and 43.28 to 43.41 mm / 40.29 to 40.46 mm (mandibular intermolar width. There were no statistically significant differences between mean dental arch widths estimated by the three studied methods, prior to and after orthodontic treatment. It may be concluded that photocopies and digitized images of the plaster models provided reliable reproductions of the dental arches for obtaining transversal intra-arch measurements.

  3. A new portable vibrator for plaster pouring: effect on the marginal fit at cylinder-abutment

    Directory of Open Access Journals (Sweden)

    Pâmela Cândida Aires Ribas de Andrade

    2012-10-01

    Full Text Available OBJECTIVE: The aim of this study was to test a new portable vibrator for plaster pouring (developed for this purpose, comparing the effect of its use on the accuracy of working cast of implant-supported restorations to the conventional vibrator. MATERIAL AND METHODS: From a master cast with 2 implants, 30 transfer moldings were made randomly and divided into three groups: Group I (GI: pouring performed in an outsourced dental laboratory with conventional plaster vibrator (10 casts, Group II (GII: pouring performed in the laboratory of the Federal University of Santa Catarina (UFSC with conventional plaster vibrator (10 casts and Group III (GIII: pouring performed with the portable vibrator fabricated for this study (10 casts. The position of the analogue and marginal adaptation of the infrastructure were verified by testing the single screw on the master model and on the working model. The measurement of misfit was blindly performed with a precision microscope and analyzing unit, Quadra-Check 200. The data were statistically analyzed by analysis of variance (ANOVA and the Holm-Sidak test (α=0.05. RESULTS: Means±standard deviations were as follows: GI: 19.19±4.73 µm; GII: 21.72±5.41 µm; GIII: 13.5±2.39 µm (P<0.05, with GIII significantly lower as compared to the other groups. CONCLUSION: Within the limitations of this study, it was concluded that a greater accuracy of working cast was achieved when a portable vibrator was used for casting molds.

  4. Properties of type IV plaster considering variation in the mold/model position during setting stage

    Directory of Open Access Journals (Sweden)

    Tarcisio José de Arruda Paes Junior

    2010-04-01

    Full Text Available Objective: To assess the influence of the position of the mold during the setting stage of type IV stone plaster Durone (Dentsply Ind. Com., Rio de Janeiro, Brazil, on the following properties: surface hardness and roughness. Methods: For the roughness test, two groups (n=6 in the form of pellets were prepared. In the first group, the surface of the base of the device was turned down during the plaster setting stage (N, in the second group this position was inverted, which has been described as an act of capsize it (E. For analysis, a roughness meter with reading precision of 0.01 μm was used. With regard to the hardness analysis, two groups with conical-shaped samples were obtained. The plasters were left to set under the same conditions of the mold/model position described for the previous experiment. Hardness measurement was performed in a durometer with a spherical penetrating tip for Rockwell readout. Three measurements were performed for each test specimen in both tests. Results: The hardness (N - 39.8, standard deviation = 3.3, E - 30.8, standard deviation = 5.6 and roughness data (N - 0.67, standard deviation = 0.17, E - 0.74, standard deviation = 0.13 submitted to the Student’s-t test (5% showed no statistically significant differences for the roughness test (0.489, but showed statistically significant differences for the hardness test (0.014. Conclusion: The variation in the mold/model position influenced the final characteristics of the specimens in terms of hardness, since those obtained with the capsize technique showed lower surface hardness, whereas for roughness these differences were not statistically significant.

  5. Dispersebility degree influence of glass fibre E in the mechanical behaviour and workability of plaster

    Directory of Open Access Journals (Sweden)

    del Río Merino, M.

    2001-03-01

    Full Text Available Although there are many research studies about plaster strengthened with glass fibre E in Spain, there are no publications which advise the users (plasterers, manufacturers of prefabricated blocks or suspended ceilings, etc about the most appropriated types of fibre E in respect to its dispersebility degree in the matrix, its lengths, the percentage, or even the type of strengthening, etc. The study of the use of this strengthener is to achieve an improvement in the mechanical behaviour of plaster as well as better conditions in the paste workability. The company Vetrotex, with the technical personnel and together with the Department of Architectural Constructions and their control (E. U. A. T. M. have started a serious research on plaster strengthened with E fibre. Conclusions shown in this first article are about the influence of the dispersebility degree of glass fibres in the mechanical behaviour of the compound as well as its workability. The degree of dispersibility of the fibres in the matrix is closely related to the type of covering used in the production of the strengthening fibres.

    Aunque existen muchos trabajos de investigación sobre el refuerzo del yeso con fibra de vidrio E en España, no hay publicaciones que asesoren a los usuarios (aplicadores de yeso proyectado, fabricantes de prefabricados como bloques o falsos techos, etc. de los tipos défibra de vidrio E más adecuados, atendiendo a su grado de dispersabilidad en la matriz, las longitudes, el porcentaje, e incluso el tipo de refuerzo, etc., a efectos de conseguir un aumento del comportamiento mecánico del yeso/escayola y unas ciertas condiciones de trabajabilidad de la pasta. La empresa Vetrotex, a través de sus técnicos y en colaboración con el Departamento de Construcciones Arquitectónicas y su control (E. U. A. T. M., decide acometer un estudio en profundidad de la escayola reforzada con fibra de vidrio E. En este primer artículo se presentan las

  6. Internal plate fixation versus plaster in displaced complete articular distal radius fractures, a randomised controlled trial.

    Science.gov (United States)

    Mulders, Marjolein A M; Walenkamp, Monique M J; Goslings, J Carel; Schep, Niels W L

    2016-02-09

    Of all distal radius fractures, 25 % are complete articular fractures (AO/OTA type C fractures). Two thirds of those fractures are displaced and require reduction. According to several International Guidelines, adequately reduced intra-articular distal radius fractures are best treated non-operatively with plaster immobilisation, while surgical fixation is suggested only when the articular step exceeds 2 mm after reduction. However, these recommendations are based on studies that did not differentiate between intra- and extra-articular distal radius fractures. Thus, no clear consensus about the best treatment for patients with displaced intra-articular distal radius fractures can be reached. Despite the lack of evidence, an increase in internal fixation of intra-articular distal radius fractures has been observed over the last decade. The aim of this study is to determine the difference in functional outcome following open reduction and plate fixation compared with non-operative treatment with closed reduction and plaster immobilisation in patients with a displaced intra articular distal radius fracture. This multicentre randomised controlled trial will randomise between open reduction and internal plate fixation (intervention group) and closed reduction and plaster immobilisation (control group). All consecutive adult patients from 18 to 65 years with a displaced intra-articular distal radius fracture (AO/OTA type C), which has been adequately reduced at the Emergency Department according to the Dutch National Guidelines, are eligible for inclusion in this study. The primary outcome is function and pain of the wrist assessed with the Patient-Rated Wrist Evaluation score (PRWE). Secondary outcomes are the Disability of the Arm, Shoulder and Hand score (DASH), pain, quality of life (SF-36), range of motion, grip strength, radiological parameters, complications, crossovers and cost-effectiveness of both treatments. A total of 90 patients will be included in this

  7. Effects of Plaster of Paris waste on the mechanical properties of pottery

    Science.gov (United States)

    Badarulzaman, N. A.; Nawi, A. M.; Ibrahim, M.

    2015-05-01

    Ceramic waste may come from ceramics industry such as Plaster of Paris(POP) mould waste. The purpose of this study is to investigate the possibility of using POP as filler in the manufacturing of pottery. The different weight percentage of filler (0 wt.%, 2 wt.%,4 wt.%, 6wt.%, 8wt.%) content were added into the composition of pottery. The samples were characterized via viscosity test and bending test. The result of the study revealed that the weight percent of waste POP increase affects the physical properties with increasing the strength values.

  8. Computer aided process of dimensional distortion determination of bounded plaster sandmix Part II

    OpenAIRE

    Pawlak, M.; Z. Niedźwiedzki

    2010-01-01

    A computer program allowing calculation of dimensional changes of mould made of cristobalite-gypsum composition in process of its heat treatment and preparation for molten metal casting is presented in this paper. The composition of the mixture and casting temperature to obtain cast of predetermined dimensions can be calculated using presented software. The base for program elaboration were the results of dilatometric test of bounded plaster sandmix composed of half hydrate α-CaSO4·0,5H2O of ...

  9. Computer aided process of dimensional distortion determination of bounded plaster sandmix Part II

    Directory of Open Access Journals (Sweden)

    M. Pawlak

    2010-01-01

    Full Text Available A computer program allowing calculation of dimensional changes of mould made of cristobalite-gypsum composition in process of its heat treatment and preparation for molten metal casting is presented in this paper. The composition of the mixture and casting temperature to obtain cast of predetermined dimensions can be calculated using presented software. The base for program elaboration were the results of dilatometric test of bounded plaster sandmix composed of half hydrate α-CaSO4·0,5H2O of various cristobalite ratio. Approximation was carried out in the range of temperatures 100÷700°C.

  10. 5% lidocaine medicated plaster in elderly patients with postherpetic neuralgia: results of a compassionate use programme in France.

    Science.gov (United States)

    Clère, Florentin; Delorme-Morin, Claire; George, Brigitte; Navez, Malou; Rioult, Bruno; Tiberghien-Chatelain, Florence; Ganry, Hervé

    2011-09-01

    Postherpetic neuralgia (PHN) is a common, debilitating complication of herpes zoster that has a major impact on patients' quality of life. PHN prevalence increases with advancing age. One treatment option is the topical analgesic 5% lidocaine (lignocaine) medicated plaster (Versatis®), which has been proven to be efficacious and well tolerated in a number of randomized clinical studies. The aim of this analysis was to assess the use of the lidocaine medicated plaster under clinical practice conditions in a patient population whose previous PHN treatment with antidepressant and/or antiepileptic agents was inadequate or was not tolerated, or for whom such treatment was contraindicated or not recommended. This was a prospective, multicentre, non-interventional observation conducted in private and public health centres in France under a compassionate use programme (CUP). To obtain this new - and, at the time, unauthorized - PHN treatment alternative, physicians (in accordance with French guidelines) had to complete standardized case report forms for each patient before his/her inclusion in the CUP. As it was a CUP and therefore a non-interventional observation, returning documented information on follow-up visits to the medication provider was voluntary, and only a limited number of physicians returned completed forms. Documentation was, however, mandatory for adverse events (AEs) occurrence. Depending on the size of the painful skin area, up to three lidocaine plasters daily were applied for a maximum of 12 hours with plaster-free intervals of at least 12 hours. The study assessed changes in the prescription of concomitant PHN medication from the start of lidocaine plaster treatment to the last follow-up visit, both in terms of the sum of all concomitant PHN treatments and stratified by type of treatment: antiepileptic drugs, tricyclic antidepressants (TCAs), serotonin reuptake inhibitors (SRIs), classical analgesics (classified as step 1, 2 or 3 according to the WHO

  11. Gray level co-occurrence and random forest algorithm-based gender determination with maxillary tooth plaster images.

    Science.gov (United States)

    Akkoç, Betül; Arslan, Ahmet; Kök, Hatice

    2016-06-01

    Gender is one of the intrinsic properties of identity, with performance enhancement reducing the cluster when a search is performed. Teeth have durable and resistant structure, and as such are important sources of identification in disasters (accident, fire, etc.). In this study, gender determination is accomplished by maxillary tooth plaster models of 40 people (20 males and 20 females). The images of tooth plaster models are taken with a lighting mechanism set-up. A gray level co-occurrence matrix of the image with segmentation is formed and classified via a Random Forest (RF) algorithm by extracting pertinent features of the matrix. Automatic gender determination has a 90% success rate, with an applicable system to determine gender from maxillary tooth plaster images. Copyright © 2016 Elsevier Ltd. All rights reserved.

  12. Treatment of postherpetic neuralgia with 5% lidocaine medicated plaster in elderly patients - subgroup analyses from three European clinical trials.

    Science.gov (United States)

    Sabatowski, Rainer; Bösl, Irmgard; König, Simone; Buchheister, Bettina; Meier, Torsten; Baron, Ralf

    2017-03-01

    To investigate short- and long-term effectiveness and safety of the 5% lidocaine medicated plaster in the treatment of postherpetic neuralgia (PHN) in elderly patients (≥70 years of age). Data from three European clinical trials was compared after stratification according to age (85% of elderly, >78% of younger patients) which was described by >51% as painful or extremely painful. Allodynia severity was markedly reduced in both groups during all three trials. Drug-related adverse events occurred in plaster provided pain relief and marked reductions in allodynia severity in elderly PHN patients with an excellent safety profile under short- and long-term treatment supporting the addition of the plaster to the treatment armamentarium for this age group. All analyzed study phases were open-label and lacking a placebo control group.

  13. [Implementing ambulatory prevention of thrombosis with low molecular weight heparin in plaster immobilization of the lower extremity].

    Science.gov (United States)

    Kock, H J; Schmit-Neuerburg, K P; Hanke, J; Terwort, A; Rudofsky, G; Hirche, H

    1994-12-01

    Plaster cast immobilisation following trauma is a major risk factor for the development of deep vein thrombosis. In our controlled, randomized and prospective study in patients with minor injuries the incidence of deep vein thrombosis was 4.3% in conservatively treated outpatients with plaster cast immobilisation of the leg (n = 163 control group without prophylaxis). By application of low molecular weight heparin once daily the number of deep vein thrombosis in the prophylaxis group (n = 176) was reduced to 0% (p = 0.006). No severe side effects of low molecular weight heparin were observed. Subcutaneous injections were self-applicated by 89% of males and 72% of females. We conclude that thromboprophylaxis with low molecular weight heparin once daily is effective to reduce the risk of deep vein thrombosis in outpatients with plaster cast immobilisation of the leg.

  14. The Terapeutic Effects of Electrical Acupuncture and Auricular-Plaster in 32 Cases of Chronic Fatigue Syndrome

    Institute of Scientific and Technical Information of China (English)

    Li Yuemei; Liu Hongping; Feng Shulan; Gong Dongfang

    2006-01-01

    Objective:To observe the therapeutic effects of electrical acupuncture and auricular-plaster therapy for chronic fatigue syndrome(CFS).Method:64 CFS patients were randomly divided into two groups.32 cases in the treatment group were treated by the electrical acupuncture and auricular-plaster therapy,and 32 cases in the control group with oral hydrocortisone.Results:The total effective rates were respectively 93.75% in the treatment group and 75.00% in the control group,with a statistically significant difference between the two groups(P<0.05).Conclusion:Electrical acupuncture and auricular-plaster therapy may show a better anti-fatigue effect than that of routine Western drugs.

  15. Populations of some molds in water-damaged homes may differ if the home was constructed with gypsum drywall compared to plaster

    Science.gov (United States)

    Starting in the 1940s, gypsum drywall began replacing plaster and lathe in the U.S. home construction industry. Our goal was to evaluate whether some mold populations differ in water- damaged homes primarily constructed with gypsum drywall compared to plaster. The dust samples fr...

  16. (AEDPH3)·(BtaH): a novel supramolecular plaster with formaldehyde adsorption and formaldehyde/ultraviolet ray-induced luminescence switching performance.

    Science.gov (United States)

    Chen, Shuo-ping; Hu, Le; Zhang, Yu-qin; Deng, Pu; Li, Cong; Chen, Xi; Yuan, Liang-jie

    2012-01-14

    A novel supramolecular plaster, (AEDPH(3))·(BtaH) (1), is synthesised and characterized. The supramolecular plaster is easy to synthesise and process, and displays good mechanical properties. It can adsorb and eliminate formaldehyde (HCHO) with high efficiency and exhibits very interesting HCHO/ultraviolet ray-induced luminescence switching.

  17. Populations of some molds in water-damaged homes may differ if the home was constructed with gypsum drywall compared to plaster

    Science.gov (United States)

    Starting in the 1940s, gypsum drywall began replacing plaster and lathe in the U.S. home construction industry. Our goal was to evaluate whether some mold populations differ in water- damaged homes primarily constructed with gypsum drywall compared to plaster. The dust samples fr...

  18. 浅议 PTA 料仓装车系统的设计%The Design of PTA Buck Silo & Truck Loading

    Institute of Scientific and Technical Information of China (English)

    彭荣杰

    2013-01-01

    The paper mainly introduced the design of PTA buck silo & truck loading .In order to better grasp the technology of PTA buck silo & truck loading, The principle of PTA buck silo & truck loading was analyzed and discussed.%  文章主要介绍了 PTA 料仓装车系统的的设计。通过对装车系统设计的一些设计原则进行了分析和探讨,以便于更好地掌握和改进PTA 料仓装车系统的技术。

  19. Treatment of localized neuropathic pain of different etiologies with the 5% lidocaine medicated plaster - a case series.

    Science.gov (United States)

    Likar, Rudolf; Demschar, Susanne; Kager, Ingo; Neuwersch, Stefan; Pipam, Wolfgang; Sittl, Reinhard

    2015-01-01

    To assess the efficacy and safety of the topical 5% lidocaine medicated plaster in the treatment of localized neuropathic pain. This was a case series at an Austrian pain clinic, using retrospective analysis. Data of 27 patients treated for localized neuropathic pain with the 5% lidocaine medicated plaster were retrospectively analyzed. Assessment included changes in overall pain intensity, in intensity of different pain qualities, and of hyperalgesia and allodynia, and changes in sleep quality. Patients (17 female, ten male; mean age 53.4±11.4 years) presented mainly with dorsalgia (16 patients) or postoperative/posttraumatic pain (seven patients); one patient suffered from both. The mean overall pain intensity prior to treatment with lidocaine medicated plaster was 8.4±1.2 on the 11-point Likert scale. In the majority of cases, the lidocaine plaster was applied concomitantly with preexisting pain medication (81.5% of the patients). During the 6-month observation period, overall mean pain intensity was reduced by almost 5 points (4.98) to 3.5±2.6. Substantial reductions were also observed for neuralgiform pain (5 points from 7.9±2.6 at baseline) and burning pain (3 points from 5.2±4.1). Sleep quality improved from 4.6±2.6 at baseline to 5.5±1.8. Stratification by pain diagnosis showed marked improvements in overall pain intensity for patients with dorsalgia or postoperative/posttraumatic pain. The lidocaine plaster was well tolerated. Overall, topical treatment with the 5% lidocaine medicated plaster was associated with effective pain relief and was well tolerated.

  20. Treatment of localized neuropathic pain of different etiologies with the 5% lidocaine medicated plaster – a case series

    Science.gov (United States)

    Likar, Rudolf; Demschar, Susanne; Kager, Ingo; Neuwersch, Stefan; Pipam, Wolfgang; Sittl, Reinhard

    2015-01-01

    Objective To assess the efficacy and safety of the topical 5% lidocaine medicated plaster in the treatment of localized neuropathic pain. Study design This was a case series at an Austrian pain clinic, using retrospective analysis. Patients and methods Data of 27 patients treated for localized neuropathic pain with the 5% lidocaine medicated plaster were retrospectively analyzed. Assessment included changes in overall pain intensity, in intensity of different pain qualities, and of hyperalgesia and allodynia, and changes in sleep quality. Results Patients (17 female, ten male; mean age 53.4±11.4 years) presented mainly with dorsalgia (16 patients) or postoperative/posttraumatic pain (seven patients); one patient suffered from both. The mean overall pain intensity prior to treatment with lidocaine medicated plaster was 8.4±1.2 on the 11-point Likert scale. In the majority of cases, the lidocaine plaster was applied concomitantly with preexisting pain medication (81.5% of the patients). During the 6-month observation period, overall mean pain intensity was reduced by almost 5 points (4.98) to 3.5±2.6. Substantial reductions were also observed for neuralgiform pain (5 points from 7.9±2.6 at baseline) and burning pain (3 points from 5.2±4.1). Sleep quality improved from 4.6±2.6 at baseline to 5.5±1.8. Stratification by pain diagnosis showed marked improvements in overall pain intensity for patients with dorsalgia or postoperative/posttraumatic pain. The lidocaine plaster was well tolerated. Conclusion Overall, topical treatment with the 5% lidocaine medicated plaster was associated with effective pain relief and was well tolerated. PMID:25565882

  1. Flow-rate fluctuations in the outpouring of grains from a two-dimensional silo.

    Science.gov (United States)

    Janda, A; Harich, R; Zuriguel, I; Maza, D; Cixous, P; Garcimartín, A

    2009-03-01

    We present experimental results obtained with a two-dimensional silo discharging under gravity through an orifice at the flat bottom. High-speed measurements provide enough time resolution to detect every single bead that goes out and this allows the measurement of the flow rate in short-time windows. Two different regimes are clearly distinguished: one for large orifices, which can be described by Gaussian fluctuations, and another for small orifices, in which extreme events appear. The frontier between those two regimes coincides with the outlet size below which jamming events are frequent. Moreover, it is shown that the power spectrum of the flow-rate oscillations is not dominated by any particular frequency.

  2. Assessing the Feasibility of Interrogating Nuclear Waste Storage Silos using Cosmic-ray Muons

    CERN Document Server

    Ambrosino, F; Cimmino, L; D'Alessandro, R; Ireland, D G; Kaiser, R; Mahon, D F; Mori, N; Noli, P; Saracino, G; Shearer, C; Viliani, L; Yang, G

    2014-01-01

    Muon radiography is a fast growing field in applied scientific research. In recent years, many detector technologies and imaging techniques using the Coulomb scattering and absorption properties of cosmic-ray muons have been developed for the non-destructive assay of various structures across a wide range of applications. This work presents the first results that assess the feasibility of using muons to interrogate waste silos within the UK Nuclear Industry. Two such approaches, using different techniques that exploit each of these properties, have previously been published, and show promising results from both simulation and experimental data for the detection of shielded high-Z materials and density variations from volcanic assay. Both detector systems are based on scintillator and photomultiplier technologies. Results from dedicated simulation studies using both these technologies and image reconstruction techniques are presented for an intermediate-sized nuclear waste storage facility filled with concrete...

  3. Validity of the Janssen Model for Layered Structures in a Silo

    Directory of Open Access Journals (Sweden)

    Abdul Qadir

    2011-07-01

    Full Text Available Granular materials are found every where despite they are poorly understood at microscopic level. The main hindrance is how to connect the microscopic properties with the macroscopic behavior and propose a rigorous unified theory. One method is to test the existing theoretical models in various configurations. In this connection we have performed experiments in different configurations of granules in a silo to determine the validity of the Janssen model under such arrangements. Two and four layered structures of different bead diameters are prepared. The effective mass at the bottom of the container in such cases have been measured. Moreover, the investigation of layered structures reveals that such configurations also follow well the Janssen model. An interesting percolation phenomenon was observed when smaller beads were stacked on larger ones, despite the model remained valid. Furthermore, it is demonstrated that Janssen law holds for larger bead diameters.

  4. Making the Paradigm Shift from Siloed Population Health Management to an Enterprise-Wide Approach.

    Science.gov (United States)

    Matthews, Marc R; Miller, Claudia; Stroebel, Robert J; Bunkers, Kari S

    2017-08-01

    Health systems across the United States have started their journeys toward population health management and the future of accountable care. Models of population health management include patient-centered medical homes and private sector accountable care organizations (ACOs). Other models include public sector efforts, such as Physician Group Practice Transition Demonstrations, Medicare Health Care Quality Demonstration Programs, Beacon Communities, Medicare Shared Savings Program, and Pioneer ACOs. As a result, health care organizations often have pockets of population health initiatives that lack an enterprise-wide strategy. The next steps are to build on these efforts, leverage the learnings from these experiences, and incorporate the initiatives into an overarching framework and a road map for the future. This paper describes the current challenge many organizations face to implement an enterprise solution, describes how to transition from existing siloed initiatives, and shares a case study of how Mayo Clinic launched its Mayo Model of Community Care.

  5. Dense bubble flow in a silo: An unusual flow of a dispersed medium

    Science.gov (United States)

    Bertho, Yann; Becco, Christophe; Vandewalle, Nicolas

    2006-05-01

    The dense flow of air bubbles in a two-dimensional silo (through an aperture D ) filled with a liquid is studied experimentally. A particle tracking technique has been used to bring out the main properties of the flow: displacements of the bubbles, transverse, and axial velocities. The behavior of the air bubbles is observed to present similarities with nondeformable solid grains in a granular flow. Nevertheless, a correlation between the bubble velocities and their deformations has been evidenced. Moreover, a new discharge law (Beverloo like) must be considered for such a system, where the flow rate is observed to vary as D1/2 and depends on the deformability of the particles.

  6. Flow Rate in the Discharge of a Two-dimensional Silo

    Science.gov (United States)

    Zuriguel, I.; Janda, A.; Garcimartín, A.; Maza, D.

    2009-06-01

    We present an experimental study of the flow rate in the discharge of a flat bottomed two-dimensional silo. The results of the flow rate dependence on the size of the orifice evidence that the Beverloo expression is not valid for small outlet sizes. This behavior is related with the properties of the flow rate which has been found to fluctuate in a gaussian like form for large orifices. On the contrary, for small orifices extreme events appear at zero flow rates causing a significant slow down of the average flow rate. These events are explained in terms of the existence of arches that block the outlet instantaneously but are unstable to permanently halt the flow.

  7. Análise estrutural de silos metálicos prismáticos

    OpenAIRE

    Lopes Neto,José Pinheiro; Nascimento,José Wallace Barbosa do; Calil Junior,Carlito

    2008-01-01

    Nos últimos anos, o crescimento da agricultura brasileira tem forçado vários setores a se adequarem aos padrões produtivos com o intuito de se manterem competitivos, frente ao processo de globalização econômica. Nesse contexto, as fábricas de ração avícola tendem a buscar novas alternativas que favoreçam a produção e reduzam custos sem afetar a qualidade do produto final. Entre essas alternativas, destaca-se o uso de silos verticais por facilitar o processo de confecção das rações e eliminar ...

  8. Silo busting: how to execute on the promise of customer focus.

    Science.gov (United States)

    Gulati, Ranjay

    2007-05-01

    For many senior executives, shifting from selling products to selling solutions--packages of products and services--is a priority in today's increasingly commoditized markets. Companies, however, aren't always structured to make that shift. Knowledge and expertise often reside in silos, and many companies have trouble harnessing their resources across those boundaries in a way that customers value and are willing to pay for. Some companies--like GE Healthcare, Best Buy, and commercial real estate provider Jones Lang LaSalle (JLL)--have restructured themselves around customer needs to deliver true solutions. They did so by engaging in four sets of activities: COORDINATION: To deliver customer-focused solutions, three things must occur easily across boundaries: information sharing, division of labor, and decision making. Sometimes this involves replacing traditional silos with customer-focused ones, but more often it entails transcending existing boundaries. JLL has experimented with both approaches. COOPERATION: Customer-centric companies, such as Cisco Systems, develop metrics for customer satisfaction and incentives that reward customer-focused cooperation. Most also shake up the power structure so that people who are closest to customers have the authority to act on their behalf. CAPABILITY: Delivering customer-focused solutions requires some employees to be generalists instead of specialists. They need experience with more than one product or service, a deep knowledge of customer needs, and the ability to traverse internal boundaries. CONNECTION: By combining their offerings with those of a partner, companies can cut costs even as they create higher-value solutions, as Starbucks has found through its diverse partnerships. To stand out in a commoditized market, companies must understand what customers value. Ultimately, some customers may be better off purchasing products and services piecemeal.

  9. Detection and enumeration of four foodborne pathogens in raw commingled silo milk in the United States.

    Science.gov (United States)

    Jackson, Emily E; Erten, Edibe S; Maddi, Neeraj; Graham, Thomas E; Larkin, John W; Blodgett, Robert J; Schlesser, Joseph E; Reddy, Ravinder M

    2012-08-01

    A nationwide survey was conducted to obtain qualitative and quantitative data on bacterial contamination of raw commingled silo milk intended for pasteurization. The levels of total aerobic bacteria, total coliforms, Enterobacteriaceae, Escherichia coli, and Staphylococcus aureus were determined using the TEMPO system. The prevalence rates and levels of presumptive Bacillus cereus, E. coli O157:H7, Listeria monocytogenes, and Salmonella spp. were determined in 214 samples. B. cereus was detected in 8.91% of samples, at 3.0 to 93 CFU/ml. E. coli O157:H7 was detected in 3.79 to 9.05% of samples, at bacteria were slightly lower in samples containing no pathogens. No correlation was observed between the levels of organisms detected with the TEMPO system and the presence or levels of any pathogen except E. coli O157:H7. A higher average log-transformed count of total viable bacteria was observed in samples positive for this organism. The high prevalence rates of target pathogens may be attributed to a variety of factors, including detection methods, sample size, and commingling of the milk in the silo. The effects of commingling likely contributed to the high prevalence rates and low levels of target pathogens because of the inclusion of milk from multiple bulk tanks. The high prevalence rates also may be the result of analysis of larger sample volumes using more sensitive detection methods. These quantitative data could be utilized to perform more accurate risk assessments and to better estimate the appropriate level of protection for dairy products and processing technologies.

  10. Identification of fungal diseases associated with imported wheat in Iranian silos.

    Science.gov (United States)

    Okhovvat, S M; Zakeri, Z

    2003-01-01

    In this study, imported wheat varieties used for cookies and bread making were evaluated for the presence of fungal diseases in the silos. Grain samples were taken and cultured on nutrient agar medium and sterile papers impregnated with nutrient. The results showed the presence of pathogenic fungi such as Ulocladium sp., Cladosporium sp., Alternaria sp., Rhizopus nigricans, Penicillium sp. and Trichothecium sp. in varieties from Australian, Mucor sp., R. nigricans, Fusarium sp., A. triticum, Helminthosporium sp. and Penicillium sp. from Argentina, Alternaria sp., Ulocladium sp., Penicillium sp., Aspergillus sp., Mucor mucedo, R. nigricans, Fusorium sp., Curvularia triticola, U. clamydosporium and C. tritici from Kazakistan varieties stored in Karaj silos or unloading trains. It is noteworthy to mention that Fusarium sp., Helminthosporium sp., Alternaria sp., A. tritici, A. triticola and U. clamydosporium are phytopathogenic fungi that often cause serious diseases on crops, produce lots of spores that are widely disseminated across the field and grow and reproduce in plant residues and diseased or wounded plant tissues and mature grains particularly under moist conditions. If in case, farmers try to use contaminated wheat grains that are distributed among them for flour, for cultivation purposes, it is highly probable that new fungal strains and species will be introduced in the areas where wheat production has never been threatened before. Fungal disease such as Indian smut or rusts is not native to Iran but are considered quarantine diseases. In addition, high incidence of contamination due to the presence of mycotoxins produced by Penicillium sp. and Aspergillus sp. in foreign wheat cultivars, could result in serious toxicity and illness in humans and birds.

  11. Construcción de silos con encofrados deslizantes - Santa Cruz de Tenerife – España

    Directory of Open Access Journals (Sweden)

    Barrios Martínez, M.

    1976-10-01

    Full Text Available These cereal and oil-cake silos are made up of 10 exterior cylindrical cells, with an inner diameter of 6 m and a height of 31.88 m. The cells are joined together by means of walls whereby four additional octagonal cells are created. Out of these, three are subdivided into four cells and the fourth forms the central silo. Below this unit there is a corridor for the emptying of the silos. The work has been carried out with a travelling form with the following characteristics: mixed with regard to shape and materials; stiff, since the top platforms are connected; and it has a constant cross-section as the dimensions of the silos remain the same throughout the whole height. The form was lifted by means of elevation devices, controlled by a centralized hydraulic mechanism. In view of the characteristics of the travelling form, the concrete used ¡n the work had to fulfill several very special conditions, notably different from these applying to the concrete that is normally used for fixed forms. For this reason, it was submitted to a great number of studies and tests until the requirements had been met. The construction was finished in record time: in the first place, because a detailed programme had been worked out in advance, consisting of a diagram of bars and preference network and secondly, because continuous concreting was applied with day and night shifts, whebery the foreseen two and a half months for finishing the silos were reduced to 12 days.Estos silos, destinados a almacenamiento de cereales y borujo, están formados por 10 celdas exteriores cilíndricas, de 6 m de diámetro interior y 31,88 m de altura, que se unen entre sí por medio de muros, dando lugar a cuatro celdas adicionales de forma octogonal. De éstas, tres están subdivididas en cuatro interceldas, quedando la cuarta como silo central. Debajo del conjunto se ha dispuesto una galería para el vaciado de los silos. La obra se ha realizado con un encofrado deslizante

  12. Compartment syndrome developed due to the plaster cast :Three cases report

    Directory of Open Access Journals (Sweden)

    Pinar Doruk

    2013-08-01

    Full Text Available Compartment syndrome can occur as a result of the complication of the plaster cast applications ,which are frequently used for fracture stabilization. This syndrome occurs due to increased compartment volume or shrinking of compartment area because of edema, hemorrage or high pressure of tissues. All of these mechanisms causes arteriolar compression, resulting nerve and muscle ischemia. Intensive and continuous pain is common and limits the motions of the patient and increases with passive stretching of the involved muscles. Swelling of limb, change in skin color, peripheral vasculatory failure symptoms such as pallor,weak arterial pulsation and as a result of peripheral nerve damage, sensorimotor deficit can also be observed. Clinical evaluation, measure of pressure within the compartment, and electroneuromyography (ENMG can be used for the diagnosis. In addition to treatment of to the treatment of etiology and pain, further treatment options such as fasciotomy, physiotherapy modalities, tendon transfers, can be performed. In this case report, we will discuss three patients with nerve lesions as a result of the compartment syndrome that developed due to the plaster casting of bone fractures. [Cukurova Med J 2013; 38(4.000: 774-778

  13. Consolidation of archaeological gypsum plaster by bacterial biomineralization of calcium carbonate.

    Science.gov (United States)

    Jroundi, Fadwa; Gonzalez-Muñoz, Maria Teresa; Garcia-Bueno, Ana; Rodriguez-Navarro, Carlos

    2014-09-01

    Gypsum plasterworks and decorative surfaces are easily degraded, especially when exposed to humidity, and thus they require protection and/or consolidation. However, the conservation of historical gypsum-based structural and decorative materials by conventional organic and inorganic consolidants shows limited efficacy. Here, a new method based on the bioconsolidation capacity of carbonatogenic bacteria inhabiting the material was assayed on historical gypsum plasters and compared with conventional consolidation treatments (ethyl silicate; methylacrylate-ethylmethacrylate copolymer and polyvinyl butyral). Conventional products do not reach in-depth consolidation, typically forming a thin impervious surface layer which blocks pores. In contrast, the bacterial treatment produces vaterite (CaCO3) biocement, which does not block pores and produces a good level of consolidation, both at the surface and in-depth, as shown by drilling resistance measurement system analyses. Transmission electron microscopy analyses show that bacterial vaterite cement formed via oriented aggregation of CaCO3 nanoparticles (∼20nm in size), resulting in mesocrystals which incorporate bacterial biopolymers. Such a biocomposite has superior mechanical properties, thus explaining the fact that drilling resistance of bioconsolidated gypsum plasters is within the range of inorganic calcite materials of equivalent porosity, despite the fact that the bacterial vaterite cement accounts for only a 0.02 solid volume fraction. Bacterial bioconsolidation is proposed for the effective consolidation of this type of material. The potential applications of bacterial calcium carbonate consolidation of gypsum biomaterials used as bone graft substitutes are discussed.

  14. Construction of the silo wall with the diameter of 15 m%直径15m筒仓仓壁的施工

    Institute of Scientific and Technical Information of China (English)

    姜德友

    2012-01-01

    结合我单位总承包的煤矿地面生产系统中原煤筒仓的施工实例,对仓壁的施工方案进行了具体的介绍,并提出了仓壁施工过程中应注意的问题,为今后同类筒仓施工提供了参考和借鉴。%Combining with the original coal silo construction example of the coal mine grounding production system generally contracted by our unit, the paper introduces the specific construction scheme of the silo wall, and puts forward matters needing attention in silo wall construction, which has provided certain guidance and reference for similar silo wall construction in future.

  15. The Present Situation and Design Advice of the Steel Silo%粮食钢板仓技术状况及设计建议

    Institute of Scientific and Technical Information of China (English)

    宋红领; 段君峰; 薛晨曦

    2016-01-01

    The article generally describes the development and situation of the steel silo in China, and the technology of grain storage of the steel silo was been analysed. Based on the characteristics of the steel silo, the effcient methods and measures to improve performance of the steel silo have been proposed.%简述了钢板仓在我国的发展历程及现状,分析了钢板仓在粮食储藏行业存在的技术和安全问题,针对钢板仓的特点,探讨了提高钢板仓储粮技术性能的措施和方法。

  16. Plaster Casts after Antique Sculpture: Their Role in the Elevation of Public Taste and in American Art Instruction.

    Science.gov (United States)

    McNutt, James K.

    1990-01-01

    Examines the social, ideological, and cultural forces in colonial United States when plaster casts of Grecian and Roman sculpture were introduced. Describes how they were used in U.S. public schools and art museums to transmit the cultural heritage at the end of the nineteenth century. (KM)

  17. [Clinical research of post-stroke motor aphasia treated with acupoint application of jieyu plaster combined with acupuncture].

    Science.gov (United States)

    Fei, Aihua; Cai, Shengchao; Xu, Bin

    2015-11-01

    To compare the difference in clinical efficacy on post-stroke motor aphasia among the combined therapy of acupoint application of jieyu plaster and acupuncture, simple acupuncture and simple acupoint application of jieyu plaster. Eighty-six patients of post-stroke motor aphasia were randomized into an acupuncture group (28 cases) , an acupoint application gruop (29 cases) and the combined therapy group (29 cases). In the acupuncture group, acupuncture was applied at the Speech No. 1 area and three-tongue needling points, once a day, 6 times a week. In the acupoint application group, jieyue plaster was applied to Yongquan (KI 1) and Laogong (PC 8), once a day, and the bilateral acupoints were selected alternatively. In the combined therapy group, the therapeutic methods of the first two groups were used in combination. The treatment lasted for 4 weeks in the three groups. The speech function score was observed and compared before and after treatment in the three groups and the efficacy was compared among the three groups. The total effective rate was 86.2% (25/29) in the combined therapy group, which was better than 67.9% (19/28) in the acupuncture group and 69.0% (20/29) in the acupoint application group (both P plaster and acupuncture apparently improves the speech function in the treatment of post-stroke motor aphasia and the efficacy is better than that of simple acupuncture or simple acupoint application.

  18. Comparison of the moulding ability of Plaster of Paris and polyester cast material in the healthy adult forearm.

    Science.gov (United States)

    Bullen, Michael; Kinealy, John; Blanchard, Romane; Rodda, Christine; Pivonka, Peter

    2017-08-16

    To quantify the moulding ability of Plaster of Paris and polyester cast materials as assessed by the novel use of peripheral quantitative computed tomography. A prospective crossover study was performed in 25 healthy volunteers aged 18-65 years. Participants' non-dominant wrist was immobilized using a synthetic polyester cast followed by a Plaster of Paris cast with three point moulding to simulate reduction of a dorsally angulated distal radius fracture. The novel use of peripheral quantitative computed tomography was used to measure the closeness of fit of each cast on an axial tomographic slice. Plaster of Paris casts were able to achieve a closer mould than polyester when measured between the bone and the cast (p=0.002), as well as between the skin and the cast (p=0.001). There was no difference when stratified on BMI. Using pQCT assessment, a closely moulded fit was able to be more consistently achieved when using Plaster of Paris when compared to polyester casts of the distal radius. III. Copyright © 2017 Elsevier Ltd. All rights reserved.

  19. Fifty Cases of Child Restless Syndrome Treated with the Integrated Method of Chinese Herbal Drugs and Auricular-Plaster Therapy

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    @@ Fifty cases of child restless syndrome were treated with oral administration of Chinese traditional herbal drugs plus auricular-plaster therapy from December 1998 to November 2001, and another 47 cases were treated with oral administration of methylphenidate as controls. The result is reported as follows.

  20. On seismic role of large floor-stand steel silo%大型落地式钢板仓地震作用分析

    Institute of Scientific and Technical Information of China (English)

    刘振华; 付迎娟; 王涛; 张震

    2016-01-01

    结合某落地式水泥钢板筒仓工程为例,利用有限元软件ABAQUS建立了三维筒仓模型,采用时程分析法,对钢板仓进行了地震作用分析,根据钢筒仓设计规范,探讨了钢筒仓的抗震性能,为落地式钢板筒仓的抗震设计提供了参考依据.%Combining with some floor-stand cement steel silo project,the paper adopts the finite element software ABAQUS to establish the three-dimension silo model,adopts the time-procedure method to undertakes the seismic analysis on the steel silo,and explores the anti-seismic per-formance of the steel silo according to the design regulations of the steel silo,so as to provide some reference for the anti-seismic design of the floor-stand steel silo.

  1. Connection joint construction technology of super-high-rise silo structure bearing plate and silo structure%超高层框筒结构楼承板与筒体连接节点施工工艺

    Institute of Scientific and Technical Information of China (English)

    程爱珍

    2015-01-01

    The paper introduces the joint connection technology principles of super-high-rise silo bearing plate and silo structure,and describes its construction technology procedures and operation points,and summarizes its construction quality,safety and environment protection measures, which guarantees the joint stress performance of bearing plate and silo connection. Therefore,it has wide application prospect in high-rise build-ing construction.%介绍了超高层框筒结构楼承板与筒体连接节点的衔接工艺原理,阐述了其施工工艺流程及操作要点,总结了施工中的质量、安全、环保措施,指出该技术保证了楼承板与筒体连接节点的受力性能,在高层建筑施工中有广泛的应用前景。

  2. Stable carbon and oxygen isotope investigation in historical lime mortar and plaster - Results from field and experimental study

    Energy Technology Data Exchange (ETDEWEB)

    Kosednar-Legenstein, B. [Institute of Applied Geosciences, Graz University of Technology, Rechbauerstrasse 12, A-8010 Graz (Austria); Dietzel, M. [Institute of Applied Geosciences, Graz University of Technology, Rechbauerstrasse 12, A-8010 Graz (Austria)], E-mail: martin.dietzel@tugraz.at; Leis, A. [Institute of Water Resources Management, Hydrogeology and Geophysics, Joanneum Research, Elisabethstrasse 16/II, A-8010 Graz (Austria); Stingl, K. [Institute of Applied Geosciences, Graz University of Technology, Rechbauerstrasse 12, A-8010 Graz (Austria)

    2008-08-15

    Lime mortar and plaster were sampled from Roman, medieval and early modern buildings in Styria. The historical lime mortar and plaster consist of calcite formed in the matrix during setting and various aggregates. The stable C and O isotopic composition of the calcite matrix was analyzed to get knowledge about the environmental conditions during calcite formation. The {delta}{sup 13}C{sub matrix} and {delta}{sup 18}O{sub matrix} values range from -31 to 0 per mille and -26 to -3 per mille (VPDB), respectively. Obviously, such a range of isotope values does not represent the local natural limestone assumed to be used for producing the mortar and plaster. In an ideal case, the calcite matrix in lime mortar and plaster is isotopically lighter in the exterior vs. the interior mortar layer according to the relationship {delta}{sup 18}O{sub matrix} = 0.61 . {delta}{sup 13}C{sub matrix} - 3.3 (VPDB). Calcite precipitation by uptake of gaseous CO{sub 2} into alkaline Ca(OH){sub 2} solutions shows a similar relationship, {delta}{sup 18}O{sub calcite} = 0.67 . {delta}{sup 13}C{sub calcite} - 6.4 (VPDB). Both relationships indicate that the {sup 13}C/{sup 12}C and {sup 18}O/{sup 16}O values of the calcite reflect the setting behaviour of the lime mortar and plaster. Initially, CO{sub 2} from the atmosphere is fixed as calcite, which is accompanied by kinetic isotope fractionation mostly due to the hydroxylation of CO{sub 2} ({delta}{sup 13}C{sub matrix} {approx} -25 per mille and {delta}{sup 18}O{sub matrix} {approx} -20 per mille ). As calcite formation continued the remaining gaseous CO{sub 2} is subsequently enriched in {sup 13}C and {sup 18}O causing later formed calcite to be isotopically heavier along the setting path in the matrix. Deviations from such an ideal isotopic behaviour may be due to the evolution of H{sub 2}O, e.g. evaporation, the source of CO{sub 2}, e.g. from biogenic origin, relicts of the natural limestone, and secondary effects, such as

  3. Treatment of localized neuropathic pain of different etiologies with the 5% lidocaine medicated plaster – a case series

    Directory of Open Access Journals (Sweden)

    Likar R

    2014-12-01

    Full Text Available Rudolf Likar,1 Susanne Demschar,1 Ingo Kager,1 Stefan Neuwersch,1 Wolfgang Pipam,1 Reinhard Sittl2 1Department of Anesthesiology and Intensive Care, Hospital Klagenfurt, Klagenfurt, Austria; 2Department of Anesthesiology, Interdisciplinary Pain Centre, University Hospital Erlangen, Erlangen, Germany Objective: To assess the efficacy and safety of the topical 5% lidocaine medicated plaster in the treatment of localized neuropathic pain. Study design: This was a case series at an Austrian pain clinic, using retrospective analysis. Patients and methods: Data of 27 patients treated for localized neuropathic pain with the 5% lidocaine medicated plaster were retrospectively analyzed. Assessment included changes in overall pain intensity, in intensity of different pain qualities, and of hyperalgesia and allodynia, and changes in sleep quality. Results: Patients (17 female, ten male; mean age 53.4±11.4 years presented mainly with dorsalgia (16 patients or postoperative/posttraumatic pain (seven patients; one patient suffered from both. The mean overall pain intensity prior to treatment with lidocaine medicated plaster was 8.4±1.2 on the 11-point Likert scale. In the majority of cases, the lidocaine plaster was applied concomitantly with preexisting pain medication (81.5% of the patients. During the 6-month observation period, overall mean pain intensity was reduced by almost 5 points (4.98 to 3.5±2.6. Substantial reductions were also observed for neuralgiform pain (5 points from 7.9±2.6 at baseline and burning pain (3 points from 5.2±4.1. Sleep quality improved from 4.6±2.6 at baseline to 5.5±1.8. Stratification by pain diagnosis showed marked improvements in overall pain intensity for patients with dorsalgia or postoperative/posttraumatic pain. The lidocaine plaster was well tolerated. Conclusion: Overall, topical treatment with the 5% lidocaine medicated plaster was associated with effective pain relief and was well tolerated. Keywords

  4. [Case-control study on the treatmentof the fifth metatarsal base fractures by cardboard compression pad versus short leg plaster].

    Science.gov (United States)

    Xu, Ying-peng; Xie, Li-min; Xu, Chao; Zhang, Yue; Li, Yu-bin; Qiao, Xin

    2014-10-01

    To compare the effect,safety,and advantage of flexible fixation with paperboard and pad versus short leg plaster in treating the fifth metatarsal base fracture,and establish the standard of diagnosis and treatment of the fifth metatarsal base fractures in flexible fixation with paperboard and pad. From June 2010 to March 2013,59 patients with the fifth metatarsal base fracture were treated with paperboard and pad fixation or short leg plaster. Patients were enrolled and divided into paperboard and pad treatment group (paperboard group) and short leg plaster treatment group (plaster group) randomly according to the random number table. In paperboard group,there were 29 cases including 9 males and 20 females with an average age of (51.79±11.40) years old; the average course of injury was (11.59±6.58) hours. In plaster group, there were 30 cases including 9 males and 21 females with an average age of (52.13+17.34) years old ;the average course of injury was (11.03±7.06) hours. According to whether the fracture line across the articular surface, in paperboard group there were 14 cases of type A,15 of type B; in plaster group,16 of type A, 14 of type B. According to the degree of dislocation,in paperboard group there were 16 cases of degree I ,13 of degree II ; in plaster group,20 were degree I ,10 were degree II. Fracture was restored according to the type in manual. Patients in paperboard group were treated with paperboard and pad, and patients in plaster group were treated with short leg plaster. Fracture was fixed for 4 to 6 weeks according to fracture healing. On the 2nd, 4th,6th, 8th week and 3rd, 6th month after fixation, patients were followed up, and the foot function score was used to evaluate the function of injured foot. X-ray of injured foot was taken on the 2nd, 4th, 6th and 8th week were used to assess fracture healing. All patients got complete follow-up. The X-ray result showed that all fracture reached at clinical healing on the 8th week after

  5. Calculation analysis of silo raft foundation%筒仓筏板基础计算分析

    Institute of Scientific and Technical Information of China (English)

    邵咏庆; 高峰

    2012-01-01

    以工程实例为背景,采用有限元软件SAP2000建立分析模型,对筒仓筏板基础进行了计算分析,模拟真实环境下可能出现影响结构安全的荷载最不利情况,为筒仓基础设计提供了依据。%Taking the engineering case as the background,using finite element software SAP2000 to establish analysis model,the paper carries out the calculation analysis on silo raft foundation,and simulates the most unfavorable loading conditions influencing the structural security under the real environment,which has provided certain basis for silo foundation design.

  6. Effect of Different Silage Storing Conditions on the Oxygen Concentration in the Silo and Fermentation Quality of Rice.

    Science.gov (United States)

    Uegaki, Ryuichi; Kawano, Kazuo; Ohsawa, Ryo; Kimura, Toshiyuki; Yamamura, Kohji

    2017-06-21

    We investigated the effects of different silage storing conditions on the oxygen concentration in the silo and fermentation quality of rice (Oryza sativa L.). Forage rice was ensiled in bottles (with or without space at the bottlemouth, with solid or pinhole cap, and with oxygen scavenger, ethanol transpiration agent, oxygen scavenger and ethanol transpiration agent, or no adjuvant) and stored for 57 days. The oxygen concentration decreased with the addition of the oxygen scavenger and increased with that of the ethanol transpiration agent. The oxygen scavenger facilitated silage fermentation and fungus generation, whereas the ethanol transpiration agent suppressed silage fermentation and fungus generation. However, the combined use of the oxygen scavenger and ethanol transpiration agent facilitated silage fermentation and also suppressed fungus generation. Overall, this study revealed the negative effects of oxygen on the internal silo and the positive effects of the combined use of the oxygen scavenger and ethanol transpiration agent on silage fermentation quality.

  7. Remanence Preservation In Burnt Silos During Pre-christian Age Fire In A Galician Castro (nw Spain)

    Science.gov (United States)

    Mohamed, K.; Rey, D.; Méndez, G.; Evans, M. E.

    Archaeomagnetic studies are usually based on measurements made on pottery or buildings that have achieved high temperatures because the results obtained are com- monly of better quality. In this study three burnt grain silos from the recently disap- peared Castro de As Laias located in Ourense (NW Spain) have provided a successful date of a pre-Christian fire. AF and thermal demagnetization were carried out to iso- late the characteristic component of magnetization. Hysteresis and IRM acquisition experiments were carried out to characterise the magnetic minerals responsible of the remanence Additionally, XRD analyses and observations under the SEM were also performed to support the magnetic data. The characteristic remanent magnetization (ChRM) has shown that two of the three studied silos burnt at the same time. Radio- carbon dating on charcoal gives an age of 181+/-61. These results also contribute to a better definition of a Secular Variation Curve (SVC) for the early Christian Age in Iberia.

  8. Clinical Observations on the Treatment of Migraine by Acupuncture plus Auricular Plaster Therapy

    Institute of Scientific and Technical Information of China (English)

    孙培华

    2007-01-01

    目的:探讨针刺配合耳压辨证治疗偏头痛的临床疗效.方法:将150例偏头痛患者随机分为观察组(n=90)和对照组(n=60).观察组患者采用针刺配合耳压辨证治疗,对照组患者采用口服西比灵治疗,并将两组的治疗效果进行对比观察.结果:观察组总有效率为94.4%,好于对照组(73.3%),观察组痊愈率为87.8%,高于对照组(55.0%).两组差异有非常显著意义(P<0.01).结论:观察组疗效明显优于对照组,运用针刺配合耳压辨证治疗偏头痛,能获得良好的临床疗效.%Objective: To investigate the clinical efficacy of acupuncture plus auricular plaster therapy for treating migraine. Methods: One hundred and fifty migraine patients were randomly allocated to an observation group (n=90) and a control group (n=60). The observation group were treated by acupuncture plus auricular plaster therapy based on syndrome differentiation and the control group, by oral administration of Flunarizine. The curative effects were compared between the two groups. Results: The total efficacy rate was 94.4% in the observation group and higher than in the control group (73.3%). The recovery rate was 87.8% in the observation group and higher than in the control group (55.0%). There were significant differences between the two groups (both P<0.01). The curative effect was significantly better in the observation group than in the control group. Conclusion: Clinically, acupuncture plus auricular plaster therapy based on syndrome differentiation has a good effect on migraine.

  9. Pregabalin, the lidocaine plaster and duloxetine in patients with refractory neuropathic pain: a systematic review

    Directory of Open Access Journals (Sweden)

    Budhia Sangeeta

    2010-11-01

    Full Text Available Abstract Background Patients frequently fail to receive adequate pain relief from, or are intolerant of, first-line therapies prescribed for neuropathic pain (NeP. This refractory chronic pain causes psychological distress and impacts patient quality of life. Published literature for treatment in refractory patients is sparse and often published as conference abstracts only. The aim of this study was to identify published data for three pharmacological treatments: pregabalin, lidocaine plaster, and duloxetine, which are typically used at 2nd line or later in UK patients with neuropathic pain. Methods A systematic review of the literature databases MEDLINE, EMBASE and CCTR was carried out and supplemented with extensive conference and grey literature searching. Studies of any design (except single patient case studies that enrolled adult patients with refractory NeP were included in the review and qualitatively assessed. Results Seventeen studies were included in the review: nine of pregabalin, seven of the lidocaine plaster, and one of duloxetine. No head-to-head studies of these treatments were identified. Only six studies included treatments within UK licensed indications and dose ranges. Reported efficacy outcomes were not consistent between studies. Pain scores were most commonly assessed in studies including pregabalin; trials of pregabalin and the lidocaine plaster reported the proportion of responders. Significant improvements in the total, sensory and affective scores of the Short-form McGill Pain Questionnaire, and in function interference, sleep interference and pain associated distress, were associated with pregabalin treatment; limited or no quality of life data were available for the other two interventions. Limitations to the review are the small number of included studies, which are generally small, of poor quality and heterogeneous in patient population and study design. Conclusions Little evidence is available relevant to the

  10. Functional treatment versus plaster for simple elbow dislocations (FuncSiE: a randomized trial

    Directory of Open Access Journals (Sweden)

    Verleisdonk Egbert JMM

    2010-11-01

    Full Text Available Abstract Background Elbow dislocations can be classified as simple or complex. Simple dislocations are characterized by the absence of fractures, while complex dislocations are associated with fractures. After reduction of a simple dislocation, treatment options include immobilization in a static plaster for different periods of time or so-called functional treatment. Functional treatment is characterized by early active motion within the limits of pain with or without the use of a sling or hinged brace. Theoretically, functional treatment should prevent stiffness without introducing increased joint instability. The primary aim of this randomized controlled trial is to compare early functional treatment versus plaster immobilization following simple dislocations of the elbow. Methods/Design The design of the study will be a multicenter randomized controlled trial of 100 patients who have sustained a simple elbow dislocation. After reduction of the dislocation, patients are randomized between a pressure bandage for 5-7 days and early functional treatment or a plaster in 90 degrees flexion, neutral position for pro-supination for a period of three weeks. In the functional group, treatment is started with early active motion within the limits of pain. Function, pain, and radiographic recovery will be evaluated at regular intervals over the subsequent 12 months. The primary outcome measure is the Quick Disabilities of the Arm, Shoulder, and Hand score. The secondary outcome measures are the Mayo Elbow Performance Index, Oxford elbow score, pain level at both sides, range of motion of the elbow joint at both sides, rate of secondary interventions and complication rates in both groups (secondary dislocation, instability, relaxation, health-related quality of life (Short-Form 36 and EuroQol-5D, radiographic appearance of the elbow joint (degenerative changes and heterotopic ossifications, costs, and cost-effectiveness. Discussion The successful

  11. The house of the Miradores by Diego de Siloe: a viewing box on the main square of Granada

    Directory of Open Access Journals (Sweden)

    Juan Manuel Barrios Rozúa

    2017-03-01

    Full Text Available By order of the local council of Granada, the arquitect Diego de Siloe designed the house of the Miradores on Bibarrambla square, one of the most harmonious examples of its kind. This article tries to complete our vision of this remarkable example of Spanish Renaissance civil architecture by providing descriptive details, unpublished images, the analysis of its compositional origins and the history of its transformations and uses.

  12. The Americleft Project: Plaster Dental Casts Versus Digital Images for GOSLON Yardstick Ratings When Used in Intercenter Comparisons.

    Science.gov (United States)

    Long, Ross E; Daskalogiannakis, John; Mercado, Ana M; Hathaway, Ronald R; Fessler, Jennifer; Russell, Kathleen A

    2017-07-01

    The purpose of this investigation was to determine reliability and validity of GOSLON Yardstick ratings using plaster casts versus photo galleries of digital images in actual intercenter comparisons. The dental arch relationships of 112 patients with complete unilateral cleft lip and palate from 3 North American cleft/craniofacial centers were rated in 2 separate studies. In the first, plaster casts were used. For a later intercenter comparison, the same dental casts were scanned, digital bases added, and two-dimensional photographic galleries (6 views) were created for each set of casts. Three raters experienced with the GOSLON Yardstick carried out 2 separate ratings of the plaster casts in the first study, then of the photographic gallery of scanned digital images of the same casts in the second study. Inter- and intrarater reliabilities were calculated using the Weighted Kappa statistic. Average scores for each patient were calculated and compared between methods with correlation statistics and a Bland-Altman plot. Kruskal-Wallis test was used to compare results between centers using both media. Reliability using both methods was very good and comparable between methods. Mean weighted Kappas were: inter-rater = 0.815 (plaster) versus 0.891 (photo); and intrarater = 0.866 (plaster) versus 0.891 (photo). There was a highly significant correlation (r = 0.920). Mean difference between centers was 0.033 of a GOSLON category. The level of significance of the differences found between centers with both methods was identical, confirming the interchangeability of both media presentations.

  13. Coping with information silos: an examination of the medication management process in residential aged care facilities (RACFs).

    Science.gov (United States)

    Tariq, Amina; Georgiou, Andrew; Westbrook, Johanna

    2014-01-01

    The aim of this study was to examine the actions of geographically dispersed process stakeholders (doctors, community pharmacists and RACFs) in order to cope with the information silos that exist within and across different settings. The study setting involved three metropolitan RACFs in Sydney, Australia and employed a qualitative approach using semi-structured interviews, non-participant observations and artefact analysis. Findings showed that medication information was stored in silos which required specific actions by each setting to translate this information to fit their local requirements. A salient example of this was the way in which community pharmacists used the RACF medication charts to prepare residents' pharmaceutical records. This translation of medication information across settings was often accompanied by telephone or face-to-face conversations to cross-check, validate or obtain new information. Findings highlighted that technological interventions that work in silos can negatively impact the quality of medication management processes in RACF settings. The implementation of commercial software applications like electronic medication charts need to be appropriately integrated to satisfy the collaborative information requirements of the RACF medication process.

  14. A Photodegradation Study of Three Common Paint and Plaster Biocides under monochromatic UV Light

    DEFF Research Database (Denmark)

    Minelgaite, Greta; Vollertsen, Jes; Nielsen, Asbjørn Haaning

    2014-01-01

    Photodegradation of the three common paint-and-plaster biocides (carbendazim, diuron and terbutryn) was investigated at controlled laboratory conditions. Samples prepared in two types of water (demineralized water and pond water) were subjected to 254 nm monochromatic UV light. Light intensity (W m......-2) in the experimental chamber was measured by a fiber optic spectrometer. The observed decline in biocide concentration was related with the light energy, accumulated during the time of degradation (kJ m-2), and 1st order photodegradation rate constants (m2 kJ-1) were determined. The obtained...... results demonstrated that diuron and terbutryn were readily degradable at the tested conditions, while carbendazim remained stable throughout the 28 – 34 hours of the experiments. Photodegradation rate constants of diuron and terbutryn were found to be slightly higher in demineralized water (0.0183 – 0...

  15. Archaeomagnetic investigation of oriented pre-Columbian lime-plasters from Teotihuacan, Mesoamerica

    Science.gov (United States)

    Soler-Arechalde, A. M.; Sánchez, F.; Rodriguez, M.; Caballero-Miranda, C.; Goguitchaishvili, A.; Urrutia-Fucugauchi, J.; Manzanilla, L.; Tarling, D. H.

    2006-10-01

    Results of an archaeomagnetic study of two excavation field seasons at the Xalla and Teopancazco residential areas of the ancient Prehispanic city of Teotihuacan, Central Mexico are reported. One-hundred and fifty three oriented samples of lime-plasters from the two archaeological sites were collected for the study. NRM directions are reasonably well grouped. Alternating field demagnetization shows single or two-component magnetizations. Rock magnetic measurements point to fine-grained titanomagnetites with pseudo-single domain behaviour. Characteristic site mean directions from both sites are correlated to the available palaeosecular variation curve for Mesoamerica. The mean directions obtained from Xalla site point to average dates of 550 AD±25 years that matches with the documented `Big Fire' of Teotihuacan (AD 575). Two consecutive construction levels at Teopancazco were estimated as AD 250-350 and AD 350-425 respectively.

  16. Cleaning plaster surfaces with agar-agar gels: evaluation of the technique

    Directory of Open Access Journals (Sweden)

    Sonia Tortajada Hernando

    2013-07-01

    Full Text Available Abstract: Cleaning plaster surfaces represent a challenge for conservators It should only be performed following fully tested methods that guarantee the conservation of such fragile material. The goal of this work is to establishing a suitable cleaning method for this type of artworks from the tested concentrations and time of applications, using agar gels on plaster supports. Morphological, porosity and weight variations have been studied. Confocal and stereomicroscopy have been used as analytical techniques, as well as the measurement of water vapor permeability and weight have been taken on the samples. La limpieza de superficies de yeso-escayola con geles de agar-agar: evaluación de la técnica Resumen: La limpieza segura y eficiente de las superficies de yeso constituye un reto y una responsabilidad para el conservador-restaurador, y debe llevarse a cabo siguiendo métodos testados que garanticen su correcta conservación. La intención de este trabajo es determinar, a partir de las concentraciones y tiempos de aplicación ensayados, cuáles serían los parámetros óptimos para la ejecución de una limpieza eficaz e inocua empleando geles de agar-agar sobre soportes de yeso. Se han comprobado las posibles variaciones morfológicas de la superficie, las variaciones de la porosidad y del peso, así como la presencia de residuos, para lo cual se ha empleado la microscopía confocal, microscopía binocular, la medida de la permeabilidad al vapor de agua y la medida del peso de las muestras.

  17. Selection of the temperature of casting the bronzes to plaster moulds

    Directory of Open Access Journals (Sweden)

    B. Pisarek

    2009-07-01

    Full Text Available The results of the investigations of the process of solidification of the bronze CuSn5Zn5Pb5-C (B555 and CuSn10-C (B10 in the hot plaster mould show in the work. For four temperatures of casting: 1200 ° C, 1180 ° C, 1160 ° C and 1140 ° C was conducted the investi-gation: the size of contraction cavity, the fulfillment of the mould cavity formative the casts of test slats about the thickness: 4 mm, 0,8 mm and 0,5 mm. It was conducted the investigation the processes sets in the arrangement the cast-mould and X-ray analysis phase XRD of compound coming into being in indirect layer created among mould and cast in the result of the thermal decomposition of the anhy-drite. It results that the temperature 1140 ° C is the optimum temperature of casting the bronze to hot plaster mould from carried out investiga-tions. The minimum thickness of the wall of the cast from the bronze B555 is 0.5 mm, and from the bronze B10 0.8 mm.The realization of casts about thinner walls is made difficult because of giving off formed gases in the result of the thermal decomposition of the anhydrite. The products of the decomposition of the anhydrite react with elements steps in the chemical composition of studied bronzes, create in the arrangement the cast-mould the indirect layer folded from: sulphites, sulphides, oxides and clean metals (Pb or their compounds, especially Sn and Sb.

  18. Breaking down the silos to decrease internal diversions and patient flow delays.

    Science.gov (United States)

    Driscoll, Molly; Tobis, Kristen; Gurka, David; Serafin, Frederick; Carlson, Elizabeth

    2015-01-01

    Hospitals strive to admit patients to the units where caregiver competencies align with the patient's condition. When the hospital's census peaks, internal diversions and the associated risks increase, which are intensified when silos exist, as segregated care negatively impacts collaboration and patient safety. In this study, a 600+-bed academic, tertiary care specialty hospital experienced an increase in internal diversions. Within the neuroscience service line, emergent neuroscience transfers from outside hospitals had been declined or internally diverted because of capacity limitations. Formalized processes for improving collaboration between health care providers related to capacity issues were required to decrease internal diversions and improve patient flow and patient safety. A pilot project was conducted on neuroscience units during a process improvement initiative. A hospital-wide internal diversion plan was developed, identifying primary and secondary placement options for all patients requiring hospitalization to support patient flow and patient safety. Forecasting tools were developed to provide units' leadership with current information on expected admissions. Daily capacity huddles were instituted to increase collaboration between patient care units. The interventions trialed during the pilot decreased internal diversions and improved patient flow. The improved collaboration resulted in an 80% decrease in declinations of emergent intensive care unit transfers from outside hospitals due to capacity limitations and a 50% decrease in the number of these patients being internally diverted to alternate intensive care units. The interventions implemented minimized internal diversions and improved patient flow. The transparency of the patient placement process led to an increased collaboration between all participants.

  19. Generation of 3-D surface maps in waste storage silos using a structured light source

    Science.gov (United States)

    Burks, B. L.; Rowe, J. C.; Dinkins, M. A.; Christensen, B.; Selleck, C.; Jacoboski, D.; Markus, R.

    1992-01-01

    Surface contours inside the large waste storage tanks typical of the Department of Energy (DOE) complex are, in general, highly irregular. In addition to pipes and other pieces of equipment in the tanks, the surfaces may have features such as mounds, fissures, crystalline structures, and mixed solid and liquid forms. Prior to remediation activities, it will be necessary to characterize the waste to determine the most effective remediation approaches. Surface contour data will be required both prior to and during remediation. The use is described of a structured light source to generate 3-D surface contour maps of the interior of waste storage silos at the Feed Materials Production Center at Fernald, OH. The landscape inside these large waste storage tanks bears a strong resemblance to some of the landscapes that might be encountered during lunar or planetary exploration. Hence, these terrestrial 3-D mapping techniques may be directly applicable to extraterrestrial exploration. In further development, it will be demonstrated that these 3-D data can be used for robotic task planning just as 3-D surface contour data of a satellite could be used to plan maintenance tasks for a space-based servicing robot.

  20. Temporal and spatial assessment of microbial communities in commercial silages from bunker silos.

    Science.gov (United States)

    Kraut-Cohen, J; Tripathi, V; Chen, Y; Gatica, J; Volchinski, V; Sela, S; Weinberg, Z; Cytryn, E

    2016-08-01

    Ensiling is a feed preservation method of moist forage crops that generally depends on naturally developing lactic acid bacteria to convert water-soluble carbohydrates into organic acids. While bacterial community dynamics have been previously assessed in bench-scale and pilot ensiling facilities, almost no studies have assessed the microbiomes of large-scale silage facilities. This study analyzed bacterial community composition in mature silage from bunker silos in three commercial production centers as related to pH, organic matter, volatile fatty acid composition, and spatial distribution within the ensiling bunker. It revealed significant physicochemical differences between "preserved" regions situated in the center and along the walls of the silage bunkers that were characterized by high concentrations of lactic acid and other volatiles and pH values below 5, and "spoiled" regions in the corners (shoulders) of the bunkers that had low lactic acid concentrations and high pH values. Preserved silage was dominated (>90 %) by lactic acid bacteria and characterized by high similarity and low taxonomic diversity, whereas spoiled silage had highly diverse microbiomes with low abundances of lactic acid bacteria (<5 %) that were sometimes characterized by high levels of Enterobacteriaceae. Spatial position had a much stronger impact on the microbial community composition than feedstock type, sampling date, or production center location supporting previous studies demonstrating that ecology and not geography is a major driver of environmental microbiomes.

  1. Educational silos in nursing education: a critical review of practical nurse education in Canada.

    Science.gov (United States)

    Butcher, Diane L; MacKinnon, Karen A

    2015-09-01

    Changes to practical nurse education (with expanded scopes of practice) align with the increasing need for nurses and assistive personnel in global acute care contexts. A case in point is this critical exploration of Canadian practical nursing literature, undertaken to reveal predominating discourses and relationships to nursing disciplinary knowledge. The objectives of this poststructural critical review were to identify dominant discourses in practical nurse education literature and to analyze these discourses to uncover underlying beliefs, constructed truths, assumptions, ambiguities and sources of knowledge within the discursive landscape. Predominant themes in the discourses surrounding practical nurse education included conversations about the nurse shortage, expanded roles, collaboration, evidence-based practice, role confusion, cost/efficiency, the history of practical nurse education and employer interests. The complex relationships between practical nursing and the disciplinary landscape of nursing are revealed in the analysis of discourses related to the purpose(s) of practical nurse education, curricula/educational programming, relationships between RN and PN education and the role of nursing knowledge. Power dynamics related to employer needs and interests, as well as educational silos and the nature of women's work, are also revealed within the intersection of various discourses.

  2. Evacuation of coal from hoppers/silos with low pressure pneumatic blasting systems

    Science.gov (United States)

    Fischer, J. S.

    1977-01-01

    The need for an efficient, economical, effective and quiet device for moving coal and other difficult bulk solids was recognized. Thus came the advent of the low pressure pneumatic blasting system - a very efficient means of using a small amount of plant air (up to 125 PSI) to eliminate the most troublesome material hang-ups in storage containers. This simple device has one moving part and uses approximately 3% of the air consumed by a pneumatic vibrator on the same job. The principle of operation is very simple: air stored in the unit's reservoir is expelled directly into the material via a patented quick release valve. The number, size, and placement of the blaster units on the storage vessel is determined by a series of tests to ascertain flowability of the problem material. These tests in conjunction with the hopper or silo configuration determine specification of a low pressure pneumatic blasting system. This concept has often proven effective in solving flow problems when all other means have failed.

  3. Case studies from three states: breaking down silos between health care and criminal justice.

    Science.gov (United States)

    Bechelli, Matthew J; Caudy, Michael; Gardner, Tracie M; Huber, Alice; Mancuso, David; Samuels, Paul; Shah, Tanya; Venters, Homer D

    2014-03-01

    The jail-involved population-people with a history of arrest in the previous year-has high rates of illness, which leads to high costs for society. A significant percentage of jail-involved people are estimated to become newly eligible for coverage through the Affordable Care Act's expansion of Medicaid, including coverage of substance abuse treatment and mental health care. In this article we explore the need to break down the current policy silos between health care and criminal justice, to benefit both sectors and reduce unnecessary costs resulting from lack of coordination. To draw attention to the hidden costs of the current system, we review three case studies, from Washington State, Los Angeles County in California, and New York City. Each case study addresses different aspects of care needed by or provided to the jail-involved population, including mental health and substance abuse, emergency care, and coordination of care transitions. Ultimately, bending the cost curve for health care and criminal justice will require greater integration of the two systems.

  4. The journey beyond silos. Teaching and learning interprofessional ethics at UTHealth.

    Science.gov (United States)

    Flaitz, Catherine M; Carlin, Nathan; Shepherd, Boyd W; McWherter, Jayne A; Bebermeyer, Richard D; Walji, Muhammad F; Spike, Jeffrey

    2011-08-01

    Interprofessional education and ethics education are two educational programs that blend together well, and, moreover, they are a natural fit for teaching in an academic health science center. The purpose of this paper is to describe our recent journey of developing and implementing an interprofessional ethics curriculum across the six schools of UTHealth. We provide an overview of the goals of the Campus-wide Ethics Program, which is housed in the McGovern Center for Humanities and Ethics, and we highlight certain innovative developments that are the result of the collaborative work of faculty and administrators from all six schools of UTHealth. In addition, a brief synopsis of the specific didactic and clinical courses in which ethics is a significant component is outlined for both the dental and the dental hygiene curricula. Lastly, we describe some of the recent scholarly activities that are a product of this new program. We are excited about our evolving efforts and the potential benefits of weaving interprofessional ethics within our school and across our campus. This article tells the story of our journey beyond "the silos" that are common among academic health science centers.

  5. Control of quality and silo storage of sunflower seeds using near infrared technology

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez-Martin, I.; Vilaescusa-Garcia, V.; Lopez-Gonzalez, F.; Oiz-Jimenez, C.; Lobos-Ortega, I. A.; Gordillo, B.; Hernandez-Hierro, J. M.

    2013-05-01

    This work assesses the application of near infrared spectroscopy technology for the quality control of sunflower seeds direct from farmers and from a storage silo. The results show that the analytical method employing near infrared spectroscopy can be used as a rapid and non-destructive tool for the determination of moisture, fat and high/low oleic acid contents in samples of sunflower seeds. The ranges obtained were comparable to those reported for classic chemical methods, and were between 4.6-21.4% for moisture; 38.4-49.6% for fat, and 60.0-93.1% for oleic acid expressed as percentage of total fatty acids. A stepwise discriminant analysis was performed to determine the most useful wavelengths for classifying sunflower seeds in terms of their (high/low) oleic acid composition. The discriminant model allows the acid contents, with a prediction rate of 90.5% for internal validation and of 89.4% for cross-validation. (Author) 23 refs.

  6. Is external fixation a better way than plaster to supplement K-wires in non-comminuted distal radius fractures?

    Science.gov (United States)

    Athar, Sajjad M; Ashwood, Neil; Aerealis, George; Bain, Gregory I

    2017-09-05

    Distal radius fractures represent about one-sixth of all fractures. There is still no consensus on the treatment of this fracture. We have several issues to assess and address; one of them is the fixation method. We tried to compare the effectiveness of two methods of stabilisation of distal radial fracture. Comparison between the techniques of Kirschner wire (K-wire) fixation with plaster and K-wire fixation with external fixation (Ex-Fix) was undertaken to assess which treatment modality gives better results in patients with distal radius fracture Frykman VII and VIII with no metaphyseal comminution. Fifty-six patients were chosen randomly and then allocated to two different modalities of stabilisation randomly as well, they were followed up; three of them were lost to follow-up because of death and two moved away from the area. Fifty-one patients were randomised in two groups: 24 were treated with K-wire and spanning Ex-Fix supplementation and 27 were treated with K-wires and plaster. Patients were prospectively monitored following the operation with a minimum follow-up of 1 year. Measurement of range of motion was obtained after surgery. Visual Analogue Scale (VAS) scores for pain and satisfaction levels were also recorded. There was statistically significant difference in favour of the Ex-Fix patient group for pain (VAS, Ex-Fix group: mean 14.9; plaster group: mean 28.1) and satisfaction (Ex-Fix group: mean 89.7;plaster group: mean 76.3). Although one would expect that range of motion would be reduced in the Ex-Fix group, there were no statistically significant differences found, with the exception of supination where results were in favour of the Ex-Fix group (mean 54.4; plaster group: mean 45.2). In our study, xternal fixator (Ex-Fix) supplementation of K-wiring favoured patients with distal radius fracture, even though there was no metaphyseal comminution, and therefore is suggested in contrast to plaster supplementation. © Article author(s) (or their

  7. The Plastered Skulls from the Pre-Pottery Neolithic B Site of Yiftahel (Israel) – A Computed Tomography-Based Analysis

    Science.gov (United States)

    Slon, Viviane; Sarig, Rachel; Hershkovitz, Israel; Khalaily, Hamoudi; Milevski, Ianir

    2014-01-01

    Three plastered skulls, dating to the Pre-Pottery Neolithic B, were found at the site of Yiftahel, in the Lower Galilee (Israel). The skulls underwent refitting and restoration processes, details of which are described herein. All three belong to adults, of which two appear to be males and one appears to be a female. Virtual cross-sections were studied and a density analysis of the plaster was performed using computed tomography scans. These were utilized to yield information regarding the modeling process. Similarities and differences between the Yiftahel and other plastered skulls from the Levant are examined. The possible role of skull plastering within a society undergoing a shift from a hunting-gathering way of life to a food producing strategy is discussed. PMID:24586625

  8. The Potential Ability of Plaster to Cause Breast Cancer as Indicated by CA15-3 and CEA Antigens in Women Working in Gypsum Factory

    Directory of Open Access Journals (Sweden)

    Ali Abdul Hussein S. AL-Janabi

    2017-07-01

    Full Text Available Plaster is an important form of gypsum that mainly used in building construction. Breast cancer was investigated among women exposure to the dust of such material. The levels of CA15-3 and carcinoembryonic antigens (CEA as indicators for breast cancer were measured in the serum of 120 women working in a plaster factory. All of involved women showed a normal level of CEA, while 12.5% of them had moderately elevated levels of CA15-3. In conclusion; plaster dust has no significant effect to cause breast cancer in working women. Moderately high levels of CA15-3 in some of exposed women may relate to liver diseases. Key words: Breast Cancer, Plaster, CA15-3, CEA

  9. Evaluation of the Population Pharmacokinetic Properties of Lidocaine and its Metabolites After Long-Term Multiple Applications of a Lidocaine Plaster in Post-Herpetic Neuralgia Patients.

    Science.gov (United States)

    Bursi, Roberta; Piana, Chiara; Grevel, Joachim; Huntjens, Dymphy; Boesl, Irmgard

    2017-01-12

    Lidocaine 5% medicated plaster is the first lidocaine containing product for chronic use. As no previous investigations have been conducted to evaluate the population pharmacokinetics of long-term exposure to lidocaine 5% medicated plasters, further insights into the evaluation of the pharmacokinetic properties of lidocaine and its metabolites were needed for the assessment of its safety. The population pharmacokinetic properties of lidocaine and its metabolites were evaluated after multiple applications of lidocaine 5% medicated plasters based on data collected for up to 14.5 months from two phase III clinical trials (up to 2.5 months in the first trial, and up to 12 months in a follow-up trial) in post-herpetic neuralgia patients. Modeling was performed using nonlinear mixed effects as implemented in NONMEM(®) (nonlinear mixed-effect modeling) v.5. A stepwise forward inclusion and backward elimination procedure were used for covariate model building. The model provides reliable estimates of the pharmacokinetic behavior of lidocaine after medicated plaster application. It was validated using simulations and showed adequate predictive properties. Apparent Clearance was estimated to be 48 L/h after application of two or fewer plasters, whereas its value increased to 67 L/h after application of three plasters. Model-based simulations predicted no accumulation of lidocaine or any of its metabolites after long-term exposure of three simultaneous plasters up to 1 year. The variability explained by adding covariates into the model for the long-term exposures of lidocaine following one plaster or three simultaneous plaster applications was found to be very small with respect to the overall between-subject variability. In conclusion, exposure to lidocaine after the application of the lidocaine medicated plaster was found to be primarily affected by the number of plasters simultaneously applied, i.e., it increased with the number of applied patches, but less than

  10. Validity of Intraoral Scans Compared with Plaster Models: An In-Vivo Comparison of Dental Measurements and 3D Surface Analysis.

    Directory of Open Access Journals (Sweden)

    Fan Zhang

    Full Text Available Dental measurements have been commonly taken from plaster dental models obtained from alginate impressions can. Through the use of an intraoral scanner, digital impressions now acquire the information directly from the mouth. The purpose of this study was to determine the validity of the intraoral scans compared to plaster models.Two types of dental models (intraoral scan and plaster model of 20 subjects were included in this study. The subjects had impressions taken of their teeth and made as plaster model. In addition, their mouths were scanned with the intraoral scanner and the scans were converted into digital models. Eight transverse and 16 anteroposterior measurements, 24 tooth heights and widths were recorded on the plaster models with a digital caliper and on the intraoral scan with 3D reverse engineering software. For 3D surface analysis, the two models were superimposed by using best-fit algorithm. The average differences between the two models at all points on the surfaces were computed. Paired t-test and Bland-Altman plot were used to determine the validity of measurements from the intraoral scan compared to those from the plaster model.There were no significant differences between the plaster models and intraoral scans, except for one measurement of lower intermolar width. The Bland-Altman plots of all measurements showed that differences between the two models were within the limits of agreement. The average surface difference between the two models was within 0.10 mm.The results of the present study indicate that the intraoral scans are clinically acceptable for diagnosis and treatment planning in dentistry and can be used in place of plaster models.

  11. Validity of Intraoral Scans Compared with Plaster Models: An In-Vivo Comparison of Dental Measurements and 3D Surface Analysis.

    Science.gov (United States)

    Zhang, Fan; Suh, Kyung-Jin; Lee, Kyung-Min

    2016-01-01

    Dental measurements have been commonly taken from plaster dental models obtained from alginate impressions can. Through the use of an intraoral scanner, digital impressions now acquire the information directly from the mouth. The purpose of this study was to determine the validity of the intraoral scans compared to plaster models. Two types of dental models (intraoral scan and plaster model) of 20 subjects were included in this study. The subjects had impressions taken of their teeth and made as plaster model. In addition, their mouths were scanned with the intraoral scanner and the scans were converted into digital models. Eight transverse and 16 anteroposterior measurements, 24 tooth heights and widths were recorded on the plaster models with a digital caliper and on the intraoral scan with 3D reverse engineering software. For 3D surface analysis, the two models were superimposed by using best-fit algorithm. The average differences between the two models at all points on the surfaces were computed. Paired t-test and Bland-Altman plot were used to determine the validity of measurements from the intraoral scan compared to those from the plaster model. There were no significant differences between the plaster models and intraoral scans, except for one measurement of lower intermolar width. The Bland-Altman plots of all measurements showed that differences between the two models were within the limits of agreement. The average surface difference between the two models was within 0.10 mm. The results of the present study indicate that the intraoral scans are clinically acceptable for diagnosis and treatment planning in dentistry and can be used in place of plaster models.

  12. Estudo comparativo de diferentes tipos de silos sobre a composição bromatológica e perfil fermentativo da silagem de milho Comparative studies on chemical composition and fermentation characteristics of corn silage

    Directory of Open Access Journals (Sweden)

    Laércio Melotti

    2002-04-01

    Full Text Available Três diferentes tipos de silos de laboratório, confeccionados a partir de baldes plásticos, sacos plásticos e manilhas de concreto com revestimento plástico, em dois diferentes graus de compactação (400 ou 600 kg de silagem/m3, foram comparados com o silo comercial tipo trincheira amostrado a 0, 50 e 100 cm da sua superfície. A planta de milho (27,3% de MS e 8,4% de PB foi picada, homogeneizada e utilizada para encher quatro silos por tratamento. Depois de abertos, estes foram amostrados para análise da composição bromatológica e perfil fermentativo. Os teores de MS e PB variaram entre os diferentes extratos do silo comercial e foram intermediários nos silos laboratoriais, indicando maior translocação de água e nutrientes naquele do que nestes. Os silos laboratoriais representaram bem os comerciais, quanto aos componentes da parede celular, amido, carboidratos solúveis e DIVMS. O pH foi menor na silagem obtida no extrato médio, intermediário no profundo e maior na superfície do silo comercial. Silagens obtidas no extrato médio também apresentaram maiores teores de nitrogênio amoniacal e ácido lático, enquanto que as obtidas no extrato profundo apresentaram as concentrações mais elevadas de ácido acético. De forma geral, os silos laboratoriais representaram bem o perfil de fermentação dos silos comerciais (pH, concentração de etanol, acético, propiônico, butírico, lático e N amoniacal, já que a maior variabilidade de resposta foi observada entre os extratos do silo comercialA commercial bunker silo and three types of experimental silos were used for determination of chemical composition and fermentation characteristics of corn silage (27.3% DM and 8.4% CP ensiled in two different densities (400 or 600kg of silage/m3: 1 commercial bunker silo sampled at 0, 50 and 100 cm from the top; 2 plastic silo with bulsen valve; 3 plastic bag; and 4 concrete pipe. Dry matter and CP concentration showed larger variation

  13. Dental arch relationships on three-dimensional digital study models and conventional plaster study models for patients with unilateral cleft lip and palate.

    Science.gov (United States)

    Asquith, J A; McIntyre, G T

    2012-09-01

    To determine if three-dimensional (3D) digital study models could replace plaster study models for the evaluation of dental arch relationships for patients with unilateral cleft lip and palate. Observational study involving plaster study models from a records archive. U.K. National Health Service. Thirty sets of study models of 5-year-old patients with unilateral cleft lip and palate were identified and scanned to produce 3D digital study models by ESM Digital Solutions Ltd. (Swords, Co. Dublin, Ireland) using an R250 Orthodontic Study Model Scanner (3Shape A/S, Copenhagen, Denmark). None. The plaster and 3D digital study models were scored using the 5-year-olds' and modified Huddart Bodenham indices and analyzed using the Friedman test (p plaster and 3D digital models. Intra-observer and interobserver reproducibility were good (0.62 to 0.83 and 0.64 to 0.78, respectively). There were no statistically significant differences between the scores for the 3D digital study models when compared to the plaster study models for either the 5-year-olds' index (p  =  .12) or for the modified Huddart Bodenham index (p  =  .506). Three-dimensional digital models are a valid alternative to traditional plaster study models for the evaluation of dental arch relationships in patients with unilateral cleft lip and palate.

  14. Fluxo de ração avícola em silos prismáticos com tremonha excêntrica Flow of poultry ration in prismatic silos with excentric hopper

    Directory of Open Access Journals (Sweden)

    Marcilene V. da Nóbrega

    2005-09-01

    Full Text Available Na avicultura atual, o uso de silos verticais para armazenagem de ração avícola nas fábricas e nas granjas, é fator fundamental, pois garantem produto de qualidade e rapidez no processo de descarga; entretanto, são detectados diversos problemas no armazenamento e no processo de escoamento da ração, devido às falhas no projeto dos silos, tendo em vista serem negligenciadas as propriedades de fluxo dos produtos, como conseqüência do não conhecimento da teoria de fluxo. Objetivou-se, com este trabalho, analisar o tipo de fluxo em silo prismático com descarga excêntrica para dois tipos de ração avícola. Determinaram-se as propriedades físicas (teor de gordura, teor de umidade e granulometria e as de fluxo (ângulo de atrito interno, efetivo ângulo de atrito interno, ângulo de atrito do produto com a parede, densidade em função da consolidação, função fluxo e fator fluxo. A análise do fluxo foi feita visualmente e através de seqüências fotográficas, variando a seção transversal de descarga, relação altura/lado e tempo de armazenamento. Com os resultados, verificou-se que a tremonha tronco piramidal com descarga excêntrica proporciona fluxo de massa para as rações analisadas.In the current poultry industry, the use of vertical silos for storage of avian poultry ration in the factories and in the farms is a fundamental factor, since they guarantee quality of product and rapid ness in the discharge process. However, several problems are detected in the storage and in the discharge of the ration due to the flaws in the project of silos, in which the flow properties of the products are neglected as a consequence of lack of knowledge of the flow theory. The objective of this work was to analyse the type of flow in prismatic silo with exentric discharge for two types of rations. The physical properties (fat content, moisture content and granulometry and flow properties of (angle of internal friction, effective angle of

  15. Talking about the Usage and Management of the Steel Plate Silo%浅谈钢板筒仓的使用与管理

    Institute of Scientific and Technical Information of China (English)

    张滨海; 吴立胜

    2011-01-01

    The silo has been used wider and wider in the bulk cargo terminal of the port for its advantage of small space occupancy,large capacity and higher mechanization . This paper introduces the status of steel plate silo used by Rizhao Port Yulang Terminal Co.,Ltd.,and the composition of the steel plate silo . Emphatically it states the operation demands in 5 stages of using the silo and items should be paid attention to. Meanwhile it introduces a few effective methods for managing the steel plate silo .%立筒仓以其占地小、储量大、机械化程序高等优点,越来越广泛地应用于港口散货码头。介绍了日照港裕廓码头有限公司现有钢板筒仓的概况和钢板筒仓的组成。着重阐述了筒仓使用5个阶段的操作要求和注意事项。并介绍了搞好钢板筒仓管理的一些行之有效的做法。

  16. Crawling spot thermal nondestructive testing (NDT) for plaster inspection and comparison with dynamic thermography with extended heating

    Science.gov (United States)

    Bison, Paolo G.; Braggiotti, Alberto; Bressan, Chiara; Grinzato, Ermanno G.; Marinetti, Sergio; Mazzoldi, Andrea; Vavilov, Vladimir P.

    1995-03-01

    Defects in building materials located parallel to the front surface, like plaster detachment, or perpendicularly, such as cracks, are detected creating a space-varying heat flux. A variant of the `flying spot' technique called `crawling spot' was developed in order to fit requirements of these materials. This nondestructive method is performed with a localized radiant heating of the surface and synchronized local temperature measurement in the IR band. The identification of delaminations and cracks was theoretically and experimentally studied using two different procedures. Results obtained for plaster detachments were compared with dynamic thermography, applied with an extended excitation of the surface and analysis of the normalized thermal contrast both in amplitude and time. Another technique requires a continuously moving spot to heat the surface while a sequence of thermograms is recorded. The temperature profile of each pixel has to be reconstructed according to the spot speed and trajectory. This procedure was applied to stone crack detection. The experimental apparatus is thoroughly described.

  17. Computer-aided design provisionalization and implant insertion combined with optical scanning of plaster casts and computed tomography data

    Science.gov (United States)

    Hara, Shingo; Mitsugi, Masaharu; Kanno, Takahiro; Tatemoto, Yukihiro

    2014-01-01

    The conventional implant prosthesis planning process currently involves confirmation of two-dimensional anatomical findings or the quantity and quality of bones using panoramic X-ray images. The introduction of computed tomography (CT) into the field has enabled the previously impossible confirmation of three-dimensional findings, making implant planning in precise locations possible. However, artifacts caused by the presence of metal prostheses can become problematic and can result in obstacles to diagnosis and implant planning. The most updated version of SimPlant® Pro has made it possible to integrate plaster cast images with CT data using optical scanning. Using this function, the obstacles created by metal prostheses are eliminated, facilitating implant planning at the actual intraoral location. Furthermore, a SurgiGuide® based on individual patient information can be created on plaster casts, resulting in easier and more precise implant insertion. PMID:24987602

  18. Cost effectiveness of a lidocaine 5% medicated plaster compared with pregabalin for the treatment of postherpetic neuralgia in the UK: a Markov model analysis.

    Science.gov (United States)

    Ritchie, Mark; Liedgens, Hiltrud; Nuijten, Mark

    2010-01-01

    Published analyses have demonstrated that the lidocaine (lignocaine) plaster is a cost-effective treatment for postherpetic neuralgia (PHN) relative to gabapentin or pregabalin. However, these analyses have been based on indirect comparisons from placebo-controlled trials, and there is evidence of a discrepancy between the outcomes of direct and indirect analyses. Fortunately, recent publication of the results of a head-to-head trial comparing the lidocaine plaster and pregabalin in patients with PHN or diabetic polyneuropathy allows customization of the existing model to more accurately reflect the relative cost effectiveness of these two products. To assess the cost-effectiveness of the lidocaine 5% medicated plaster compared with pregabalin for the treatment of PHN in the UK primary-care setting. A Markov model has been developed to assess the costs and benefits of the lidocaine plaster and pregabalin over a 6-month time horizon for the treatment of patients with PHN who are intolerant to tricyclic antidepressants and in whom analgesics are ineffective or contraindicated. The model structure allows for differences in costs, utilities (derived from published data and from the head-to-head trial) and transition probabilities between the initial 30-day run-in period and maintenance therapy, and also takes account of add-in medication and drugs received by patients discontinuing therapy. The calculation was based on data from the recent head-to-head trial described above. Additional data sources included published literature, discussions with a Delphi panel, official price/tariff lists and national population statistics. The study was conducted from the perspective of the UK National Health Service (NHS). The base-case analysis (1.71 lidocaine plasters per day used in the head-to-head trial for the PHN population) indicated that the total cost of treating PHN patients for 6 months with the lidocaine plaster was pound 980 per patient treated, compared with pound 784

  19. Measurements using orthodontic analysis software on digital models obtained by 3D scans of plaster casts : Intrarater reliability and validity.

    Science.gov (United States)

    Czarnota, Judith; Hey, Jeremias; Fuhrmann, Robert

    2016-01-01

    The purpose of this work was to determine the reliability and validity of measurements performed on digital models with a desktop scanner and analysis software in comparison with measurements performed manually on conventional plaster casts. A total of 20 pairs of plaster casts reflecting the intraoral conditions of 20 fully dentate individuals were digitized using a three-dimensional scanner (D700; 3Shape). A series of defined parameters were measured both on the resultant digital models with analysis software (Ortho Analyzer; 3Shape) and on the original plaster casts with a digital caliper (Digimatic CD-15DCX; Mitutoyo). Both measurement series were repeated twice and analyzed for intrarater reliability based on intraclass correlation coefficients (ICCs). The results from the digital models were evaluated for their validity against the casts by calculating mean-value differences and associated 95 % limits of agreement (Bland-Altman method). Statistically significant differences were identified via a paired t test. Significant differences were obtained for 16 of 24 tooth-width measurements, for 2 of 5 sites of contact-point displacement in the mandibular anterior segment, for overbite, for maxillary intermolar distance, for Little's irregularity index, and for the summation indices of maxillary and mandibular incisor width. Overall, however, both the mean differences between the results obtained on the digital models versus on the plaster casts and the dispersion ranges associated with these differences suggest that the deviations incurred by the digital measuring technique are not clinically significant. Digital models are adequately reproducible and valid to be employed for routine measurements in orthodontic practice.

  20. Treatment of localized neuropathic pain of different etiologies with the 5% lidocaine medicated plaster – a case series

    OpenAIRE

    Likar R; Demschar S; Kager I; Neuwersch S; Pipam W; Sittl R

    2014-01-01

    Rudolf Likar,1 Susanne Demschar,1 Ingo Kager,1 Stefan Neuwersch,1 Wolfgang Pipam,1 Reinhard Sittl2 1Department of Anesthesiology and Intensive Care, Hospital Klagenfurt, Klagenfurt, Austria; 2Department of Anesthesiology, Interdisciplinary Pain Centre, University Hospital Erlangen, Erlangen, Germany Objective: To assess the efficacy and safety of the topical 5% lidocaine medicated plaster in the treatment of localized neuropathic pain. Study design: This was a case series at an Austrian pain...

  1. POTENTIAL APPLICATIONS OF TRANSPARENT FABRIC BASED ON NANOFIBRES FOR THE STRENGTHENING OF PLASTERS DECORATED WITH PAINTINGS AND FRESCOES

    Directory of Open Access Journals (Sweden)

    Klára Kroftová

    2015-10-01

    Full Text Available Nanomaterials have been increasingly used in the construction industry in the last decades. Nanomaterials have been tested in specific applications focusing on the restoration and conservation of heritage buildings, mainly their surfaces. Nanofibre materials represent a separate area within this field of research and their applications in the construction and conservation practice are still very limited. The article summarizes the possibilities of strengthening plasters decorated with wall paintings with nanomaterials.

  2. Effect of different forms of silica on the physical and mechanical properties of gypsum plaster composites

    Directory of Open Access Journals (Sweden)

    Khalil, A. A.

    2013-12-01

    Full Text Available Gypsum plaster/silica composites prepared by dry blending (0.2-10 % natural sand, silica fume or silica gel and subsequently hydrated. Their physical and mechanical properties, including normal consistency, setting time, apparent porosity, bulk density and compressive strength, were determined after hydration for 7- and 28-days. The results indicated that adding different forms of silica lowered the bulk density and increased the normal consistency, setting time, apparent porosity and, to some limited extent, compressive strength of the composites. This improvement in properties can be attributed to the existence of silica in the interstitial pores in the hardened plaster matrices. While most of the composites revealed only scant rises in compressive strength, their composition was beneficial in so far as it included either a readily available low-cost constituent (sand or industrial by-products. Consequently, the formed plaster-silica composites are of economic value, contribute to a cleaner environment by minimizing waste and can be used for applications where high porosity, lightweight units are required or recommended for low-cost buildings.Se prepararon pastas compuestas de yeso y sílice mediante la mezcla en seco de yeso con distintas proporciones (0,2- 10 % de arena natural, o gel o humo de sílice, procediéndose a continuación a su hidratación. A fin de determinar las propiedades físicas y mecánicas de las pastas, a los 7 y los 28 días de hidratación se hallaron su fluidez, tiempo de fraguado, porosidad aparente, densidad aparente y resistencia a la compresión. Los resultados obtenidos indican que al incorporar las distintas modalidades de sílice a la mezcla, disminuyó la densidad aparente y aumentaron la fluidez, el tiempo de fraguado, la porosidad aparente y, en menor medida, la resistencia a la compresión de las muestras. Se considera que esta mejora de las propiedades del material se debe a la presencia de sílice en los

  3. Assessing the feasibility of interrogating nuclear waste storage silos using cosmic-ray muons

    Science.gov (United States)

    Ambrosino, F.; Bonechi, L.; Cimmino, L.; D'Alessandro, R.; Ireland, D. G.; Kaiser, R.; Mahon, D. F.; Mori, N.; Noli, P.; Saracino, G.; Shearer, C.; Viliani, L.; Yang, G.

    2015-06-01

    Muon radiography is a fast growing field in applied scientific research. In recent years, many detector technologies and imaging techniques using the Coulomb scattering and absorption properties of cosmic-ray muons have been developed for the non-destructive assay of various structures across a wide range of applications. This work presents the first results that assess the feasibility of using muon radiography to interrogate waste silos within the U.K. Nuclear Industry. Two such approaches, using different techniques that exploit each of these properties, have previously been published, and show promising results from both simulation and experimental data for the detection of shielded high-Z materials and density variations from volcanic assay. Both detection systems used are based on scintillator and photomultiplier technologies. Results from dedicated simulation studies using both these proven technologies and image reconstruction techniques are presented for an intermediate-sized legacy nuclear waste storage facility filled with concrete and an array of uranium samples. Both results highlight the potential to identify uranium objects of varying thicknesses greater than 5 cm within real-time durations of several weeks. Increased contributions from Coulomb scattering within the concrete matrix of the structure hinder the ability of both approaches to resolve similar objects of 2 cm dimensions even with increased statistics. These results are all dependent on both the position of the objects within the facility and the locations of the detectors. Results for differing thicknesses of concrete, which reflect the non-standard composition of these complex, legacy structures under interrogation, are also presented alongside studies performed for a series of data collection durations. It is anticipated that with further research and optimisation of detector technologies and geometries, muon radiography in one, or both of these forms, will play a key role in future

  4. Effect of an admixture from Agave americana on the physical and mechanical properties of plaster

    Directory of Open Access Journals (Sweden)

    Ochoa, J. C.

    2013-03-01

    Full Text Available Physical and mechanical properties of a plaster paste added with an organic admixture, of the leaves of Agave americana, were studied. Plastic consistency behavior was evaluated and the water/gypsum(w/g ratio was determined for each dosage of the admixture. Admixtur eeffect on setting was evaluated too. The chemical transformation of the hemihydrated form to gypsum (dihydrated form was studied using a novel technique based on a moisture analyzer by halogen light. Flexural and compressive strengths were measured. The results show that ,for the same consistency, accordingly mechanical strengths were improved too. The setting times were increased which would enhance the application time of plaster and would reduce plastic shrinkage, common problems in this type of material. The changes in these physical properties not substantially affect the final mechanical strengths.

    Se estudiaron algunas propiedades físicas y mecánicas de pastas de yeso de construcción adicionadas con un aditivo de origen orgánico, producto de las hojas de la planta Agave americana. Se evaluó el comportamiento plástico de la pasta mediante ensayos de consistencia y se determinó, para cada dosificación, su relación agua/ yeso (a/y. Se evaluó la incidencia del aditivo en los tiempos de fraguado. La transformación química del hemihidrato a yeso dihidrato se estudió mediante una novedosa técnica basada en un analizador de humedad por luz halógena. Se midieron las resistencias mecánicas a flexo-tracción y a compresión. Los resultados del estudio muestran que, para una misma consistencia, se mejoran las resistencias mecánicas. Los tiempos de fraguado de la pasta se aumentaron lo que ayudaría mejorar los tiempos de aplicación del yeso y a disminuir las retracciones plásticas. Las modificaciones de estas propiedades físicas no afectan considerablemente las resistencias mecánicas finales.

  5. Coeficiente de transferência de carga nas fundações de silos verticais cilíndricos

    Directory of Open Access Journals (Sweden)

    Marivone Z. Fank

    2015-09-01

    Full Text Available RESUMOO dimensionamento das estruturas armazenadoras de grãos carece de uma norma brasileira que prescreva sobre seus projetos e ações; contudo, existem muitas lacunas no estado atual do conhecimento sendo imprescindíveis pesquisas adicionais sobre o tema. Com o objetivo de determinar a distribuição das cargas nas fundações dos silos foram instrumentadas, por meio de células de carga, quatro estacas localizadas sob o anel de um silo protótipo. O experimento ocorreu durante o período de agosto a dezembro de 2009 em Palotina, PR. As leituras das células foram realizadas por sistema automático de aquisição de dados durante o carregamento de grãos de milho e, a partir dos resultados, pode-se destacar um coeficiente de transferência médio de 0,30 para o anel até o carregamento de 44% do silo, a partir do qual ocorreu um incremento na taxa de transferência. As cargas máximas atuantes nas estacas instrumentadas foram de 800, 845, 520 e 600 kN, correspondentes a coeficientes de transferência de 0,48; 0,51; 0,31 e 0,36, respectivamente. Assim, o coeficiente regionalmente adotado de 0,30 para o dimensionamento das fundações do anel está subestimado fazendo-se necessária uma análise mais criteriosa nas taxas de transferência.

  6. 5% lidocaine medicated plaster versus pregabalin in post-herpetic neuralgia and diabetic polyneuropathy: an open-label, non-inferiority two-stage RCT study.

    Science.gov (United States)

    Baron, Ralf; Mayoral, Victor; Leijon, Göran; Binder, Andreas; Steigerwald, Ilona; Serpell, Michael

    2009-07-01

    To compare efficacy and safety of 5% lidocaine medicated plaster with pregabalin in patients with post-herpetic neuralgia (PHN) or painful diabetic polyneuropathy (DPN). This was a two-stage adaptive, randomized, open-label, multicentre, non-inferiority study. Data are reported from the initial 4-week comparative phase, in which adults with PHN or painful DPN received either topical 5% lidocaine medicated plaster applied to the most painful skin area or twice-daily pregabalin capsules titrated to effect according to the Summary of Product Characteristics. The primary endpoint was response rate at 4 weeks, defined as reduction averaged over the last three days from baseline of > or = 2 points or an absolute value of plaster and 61.5% receiving pregabalin were considered responders (corresponding numbers for the per protocol set, PPS: 65.3% vs. 62.0%). In PHN more patients responded to 5% lidocaine medicated plaster treatment than to pregabalin (PPS: 62.2% vs. 46.5%), while response was comparable for patients with painful DPN (PPS: 66.7% vs 69.1%). 30% and 50% reductions in NRS-3 scores were greater with 5% lidocaine medicated plaster than with pregabalin. Both treatments reduced allodynia severity. 5% lidocaine medicated plaster showed greater improvements in QoL based on EQ-5D in both PHN and DPN. PGIC and CGIC scores indicated greater improvement for 5% lidocaine medicated plaster treated patients with PHN. Improvements were comparable between treatments in painful DPN. Fewer patients administering 5% lidocaine medicated plaster experienced AEs (safety set, SAF: 18.7% vs. 46.4%), DRAEs (5.8% vs. 41.2%) and related discontinuations compared to patients taking pregabalin. 5% lidocaine medicated plaster showed better efficacy compared with pregabalin in patients with PHN. Within DPN, efficacy was comparable for both treatments. 5% lidocaine medicated plaster showed a favourable efficacy/safety profile with greater improvements in patient satisfaction and Qo

  7. Diseño de un silo cilíndrico metálico atornillado para el almacenamiento de productos granulares

    OpenAIRE

    Ravenet Regales, Juan Ignacio

    2004-01-01

    El objeto de este proyecto pretende el diseño, cálculo y construcción de un silo cilíndrico metálico para el almacenamiento de los productos de la limpia del maíz. En dicho proyecto se realiza el estudio de un silo, aplicando las teorías más destacadas que se han dedicado al cálculo, diseño y resolución de problemas aparecidos en silos. Se exponen las normas, teorías y códigos de los principales especialistas mundiales extraído de diversa bibliografía. Se estudian aspectos como...

  8. Reverse Tissue Expansion in Gastroschisis: What to do if the Defect is too large to close after Silo Removal?

    Directory of Open Access Journals (Sweden)

    Boma T Adikibi

    2014-10-01

    Full Text Available A female baby with an antenatal diagnosis of gastroschisis was transferred to our institution. The defect was large but the bowel was in good condition and a silo was placed. After successful reduction of the bowel the abdominal wall defect was too large to allow fascial or even skin closure. We utilised a Gore-tex patch with two prolene purse string sutures placed concentrically to enable the diameter of the patch to be sequentially reduced. This enabled gradual stretching of the tissues with a progressive reduction in the size of the defect. The patch was removed after 8 days and a delayed fascial closure was achieved.

  9. Estudo de viabilidade econômica de um silo metálico para Agricultura Familiar

    Directory of Open Access Journals (Sweden)

    Armando Kazuo Fujii

    2016-03-01

    Full Text Available Este trabalho desenvolveu um web-aplicativo para demonstrar um estudo de viabilidade econômica para os produtores familiares adquirirem um silo metálico de pequeno porte, baseado na diferença de valores pagos aos produtores de milho na safra e na entressafra, utilizando financiamento disponível no Governo Federal. Foi utilizada a metodologia de taxa do retorno do investimento, que mostrou sua viabilidade, pois o retorno ocorre em um prazo inferior ao da conclusão do pagamento do financiamento.

  10. 筒仓下活化给料机安装工艺%Installation Process of Uncoaler Feeder under Silo

    Institute of Scientific and Technical Information of China (English)

    于鹏; 韩伯涛

    2013-01-01

    The silo technology in Huanghua Port Phase III Project is used in our country for the first time. Each silo bottom sets six holes for coal decline. An uncoaler feeder is set under each hole. The pouring of silo has been completed when the installa-tion of uncoaler feeder starts. Moreover, the space at the lower part of the silo is narrow and small with poor conditions. Those factors cause difficulties to the installation of uncoaler feeder, especially the device taking its position under silo. The most dif-ficult point is the transportation of the main part of the device to the inside of silo. The method is adopted that the main parts of uncoaler feeder slip from the hole to the position, which greatly reduces construction time, improves construction efficiency, and ensure the construction period.%黄骅港三期工程在国内首次采用筒仓工艺,每座筒仓底设置6个洞口,筒仓下部6个落煤口设置活化给料机,每个洞口布置1台活化给料机,活化给料机安装时筒仓已经浇筑完成,且筒仓下部空间狭小,条件恶劣,对设备本体进入筒仓落煤口下就位造成一定难度。活化给料机安装难点在于本体如何进入筒仓内,故采用从洞口滑入方式进行安装,大大减少了施工时间,提高施工效率,保证了工期。

  11. [Clinical observation of dog days moxibustion plaster therapy in treatment of allergic rhinitis of different patterns/syndromes].

    Science.gov (United States)

    Lin, Yong-kai; Liang, Gui-hong; Huang, Yu-xin; Sun, He; Zhang, Tian-cheng; Qu, Chong-zheng

    2014-10-01

    To explore the efficacy and feasibility of dog days moxibustion plaster therapy in treatment of allergic rhinitis of different patterns/syndromes. Allergic rhinitis of lung deficiency and invasion of cold, spleen qi deficiency and kidney yang deficiency, 56 patients for each pattern/syndrome were randomized into a plaster therapy group and a nasal spray group, 28 cases in each one. In the plaster therapy group, according to the pattern/syndrome differentiation, with literature retrieval method, 3 acupoints of high frequency utility in clinic were selected as one group in acupoint plaster therapy. For lung deficiency and invasion of cold pattern/syndrome, Feishu (BL 13), Fengmen (BL 12) and Hegu (LI 4) were selected. For spleen qi deficiency pattern/syndrome, Pishu (BL 21), Zusanli (ST 36) and Dazhui (GV 14) were selected. For kidney yang deficiency pattern/ syndrome, Shenshu (BL 23), Dingchuan (EX-B 1) and Bailao (EX-HN 15) were selected. Separately, on July 13, 2013, July 23, 2013, August 2, 2013 and August 12, 2013, the aucpoint plaster therapy was applied, 2 to 4 h (1 to 2 h for children) each time. In the nasal spray group, beclometasone dipropionate aqueous nasal spray, 2 presses one nostril each time, 2 to 3 times a day, continuously for 4 weeks. The symptom score and efficacy were compared before and after treatment in the patients of the two groups. The symptom scores of 3 patterns/syndromes were all apparently improved after treatment as compared with those before treatment in the patients of the two groups (all Pplaster therapy group was better than that of the nasal spray group (Pplaster therapy group, better than 84.6% (22/26) in the nasal spray group (Pplaster therapy group, obviously better than 76.9% (22/26) in the nasal spray group (Pplaster therapy group, better than 76.9% (22/26) in the nasal spray group (Pplaster therapy achieves definite efficacy on allergic rhinitis at the acupoints selected based on the differentiation of different patterns

  12. Studies on termite hill and lime as partial replacement for cement in plastering

    Energy Technology Data Exchange (ETDEWEB)

    Olusola, K.O.; Olanipekun, E.A.; Ata, O.; Olateju, O.T. [Obafemi Awolowo University, Ile-Ife, Osun State (Nigeria). Department of Building

    2006-03-15

    This study investigated the compressive strength and water absorption capacity of 50x50x50mm mortar cubes made from mixes containing lime, termite hill and cement and sand. Two mix ratios (1:4 and 1:6) and varying binder replacements of cement with lime or termite hill amounting to 0%, 10%, 20%, 30%, 40% and 50% were used. Test results showed that the compressive strength of the mortar cubes increases with age and decreases with increasing percentage replacement of cement with lime and termite hill. However, for mix ratio 1:6, up to 20% replacement of cement with either lime or termite hill, all the mortar cubes had the same strength; subsequently, the termite hill exhibited a higher compressive strength. For mix ratio 1:4, mortar cubes made from lime/cement and termite hill/cement mixtures had the same strength at 50% replacement. Generally, water absorption is higher in mixtures containing lime (18.10% and 14.20% for mix ratios 1:6 and 1:4, respectively, both at 50% replacement level) than those containing termite hill (16.10% and 13.02% for mix ratios 1:6 and 1:4, respectively, both at 50% replacement level). Termite hills seem to be promising as a suitable, locally available housing material for plastering. (author)

  13. Light Steel-Timber Frame with Composite and Plaster Bracing Panels

    Directory of Open Access Journals (Sweden)

    Roberto Scotta

    2015-11-01

    Full Text Available The proposed light-frame structure comprises steel columns for vertical loads and an innovative bracing system to efficiently resist seismic actions. This seismic force resisting system consists of a light timber frame braced with an Oriented Strand Board (OSB sheet and an external technoprene plaster-infilled slab. Steel brackets are used as foundation and floor connections. Experimental cyclic-loading tests were conduced to study the seismic response of two shear-wall specimens. A numerical model was calibrated on experimental results and the dynamic non-linear behavior of a case-study building was assessed. Numerical results were then used to estimate the proper behavior factor value, according to European seismic codes. Obtained results demonstrate that this innovative system is suitable for the use in seismic-prone areas thanks to the high ductility and dissipative capacity achieved by the bracing system. This favorable behavior is mainly due to the fasteners and materials used and to the correct application of the capacity design approach.

  14. Effective and Economic Offloading of Diabetic Foot Ulcers in India with the Bohler Iron Plaster Cast.

    Science.gov (United States)

    Saikia, Priyanka; Hariharan, Rajalakshmi; Shankar, Nachiket; Gaur, Anil Kumar; Jose, Naveen Matthew

    2016-04-01

    Economic constraints are a major obstacle to the implementation of offloading casts in India. The aim of this study is to monitor the healing and activity limitations related to Bohler iron plaster cast (BIPC) when used for offloading diabetic neuropathic plantar foot ulcers. Thirty patients were cast for 1 month and evaluated for healing using the Pressure Ulcer Scale for Healing (PUSH), and for activity limitation using the Lower Extremity Functional Scale (LEFS). The change in the scores after intervention was the outcome measure. There was good healing as evidenced by a statistical difference in mean PUSH scores. The baseline PUSH score of 9.76-0.41 (T1-SEM) was greater than follow-up PUSH score of 6.32 + 0.41 (T2 + SEM) and the p value ulcer area, exudate, and tissue type. There was no mobility effect as there was no significant difference in LEFS. Significant negative correlation was there between PUSH and LEFS. The r value was less than -0.7 both at baseline and after intervention. The combined benefits of good healing, lack of affect on lower extremity function, the ease of application and dressing, and relative affordability make BIPC a commendable offloading modality for the management of diabetic plantar ulcers.

  15. Soil Application of Tannery Land Plaster: Effects on Nitrogen Mineralization and Soil Biochemical Properties

    Directory of Open Access Journals (Sweden)

    Caterina Giacometti

    2012-01-01

    Full Text Available Tannery land plaster (TLP is a byproduct of lime hydrolysis of leather shavings. Its use in agriculture (organic C ≈ 17%, N ≈ 6% dm could represent an alternative to landfill or incineration, but the high Cr(III content (≈5% dm makes it necessary to evaluate the effect on soil biochemical properties. TLP was therefore added at the rates of 220 and 440 kg of N ha−1 to 2 agricultural soils and incubated for 56 days under controlled conditions. Extractable NH4 +-N and NO3 −-N, CO2-C evolution, microbial biomass-N, protease activity, and extractable Cr were monitored. The organic N was readily mineralized (>50% in the first week and a significant increase in microbial activity was measured, regardless of soil type and addition rate. Extractable Cr(III quickly decreased during the incubation. The absence of a negative impact on soil biochemical properties seems to support the use of TLP in agriculture, although further investigations in long-term field experiments are suggested.

  16. Study on Tongkuaixiao Babu Plaster(痛块消巴布剂)in Treating Cancer Pain

    Institute of Scientific and Technical Information of China (English)

    万冬桂; 李佩文

    2004-01-01

    Objective: To explore the efficacy of Tongkuaixiao Babu plaster (痛块消巴剂, TKXBBP)in treating cancer pain. Methods: In the clinical observation, sixty-five patients with moderate or severe cancer pain were randomly divided into two groups: 32 in the treated group (TKXBBP group) and 33 in the control group (Bucinnazine group). The therapeutic effects in relieving pain, improving quality of life (QOL),and the rate of satisfaction the patients felt of the two groups were compared respectively. Results: TKXBBP was effective in treating cancer pain. There wasn't any statistically significant difference in total effective rate (P>0.05), but the statistical difference was significant in obvious remission rate (P<0.05) between the treated and control group, and the effect on serious pain shown in the treated group was better than that of the control group (P<0.05). The difference in the initiation time of relieving cancer pain was insignificant (P>0.05), while in the remission period, the treated group showed its treatment was obviously superior to that of the control group (P<0.05). TKXBBP showed better effect in the improvement of QOL (P<0.05)and satisfaction rate, with significant difference between the treated and the control groups (P<0.01). Conclusion: TKXBBP's effect in treating cancer pain was obvious, its application was safe and convenient. It was shown that the external treatment with this kind of Chinese medicine had great advantage in treating cancer pain.

  17. Effect of 5% lidocaine medicated plaster on pain intensity and paroxysms in classical trigeminal neuralgia.

    Science.gov (United States)

    Tamburin, Stefano; Schweiger, Vittorio; Magrinelli, Francesca; Brugnoli, Maria Paola; Zanette, Giampietro; Polati, Enrico

    2014-11-01

    Trigeminal neuralgia (TN) is a neuropathic pain condition affecting one or more branches of the trigeminal nerve. It is characterized by unilateral, sudden, shock-like, and brief painful attacks, which follow the distribution of trigeminal nerve branches, and with no other accompanying sensorimotor or autonomic signs and symptoms. Current guidelines stipulate which therapies represent first-, second-, and third-line treatments for TN, but there is a consistent mismatch between the therapeutic guidelines and the patient's preferences and expectations. We report on 2 patients with classical TN in whom conventional drugs for TN were not tolerated. In these patients, treatment with 5% lidocaine medicated plaster (LMP) resulted in reduction of pain intensity and the number of pain paroxysms. LMP is known to block the sodium channels on peripheral nerves and may cause a selective and partial block of Aδ and C fibers. According to the TN ignition hypothesis, blockage of peripheral afferents by LMP may reduce pain paroxysms. The effect of LMP may outlast the pharmacokinetics of the drug by reducing pain amplification mechanisms in the central nervous system. LMP has limited or no systemic side effects. LMP may be an effective and well-tolerated treatment option for TN in those patients who do not tolerate or who refuse other therapies. Future randomized controlled studies should better address this issue. © The Author(s) 2014.

  18. Pain in the room of plasters of the traumatology emergency unit

    Directory of Open Access Journals (Sweden)

    Inmaculada Aponte Tomillo

    2010-03-01

    Full Text Available In the emergency department the pain is the symptom more frequent than they undergo the patients, the presence of this one is considered like a useless and unnecessary suffering since it can get to control itself by means of the drug administration. The objective of this study is to know the existence and intensity the pain and if analgesia is administered in the traumatology emergency unit. It has been realised by means of a questionnaire in that picks up the variables: sex, age, diagnosis, pain and administration of analgesia. With respect to the result it exists 39,4% of fractures of radio, followed of 24,2% of fracture of metacarpianos. The pain in the room of plasters: Visual scale Analogical EVA (10 the 15,2% and EVA (7 the 21,2% of the patients. As far as the administration of analgesia to the 59,1% of the patients no was administered to him. In conclusion, the intensity of the pain that undergoes our patients during the manipulation of the fractures is because a percentage very lifted is reduced and immobilized without analgesia administration. This high prevalence of the pain puts in prohibition the welfare quality.

  19. Improving corn silage quality in the top layer of farm bunker silos through the use of a next-generation barrier film with high impermeability to oxygen.

    Science.gov (United States)

    Borreani, G; Tabacco, E

    2014-01-01

    This study examined the effect on the fermentation, chemical, and microbiological quality of corn silage covered with a new-generation high oxygen barrier film (HOB) made with a special grade of ethylene-vinyl alcohol (EVOH) compared with a standard polyethylene film (PE). Two bunkers (farms 1 and 2) were divided into 2 parts lengthwise so that half of the silo would be covered with PE film and the other with HOB film. Plastic net bags with fresh chopped corn were buried in the upper layer (close to and far from the wall) and in the central part of the bunkers. During spring-summer consumption, the bags were unloaded, weighed, and subsampled to analyze the dry matter (DM) content, neutral detergent fiber and starch contents, pH, lactic and monocarboxylic acids, yeast and mold counts, aerobic and anaerobic spore-former counts, and aerobic stability. We also determined the economic benefit of applying the novel covering. The top layer of silage conserved under the HOB film had a higher lactic acid content and lower pH; lower counts of yeasts, molds, and aerobic and anaerobic spore-formers; higher aerobic stability; and lower DM losses than the silage conserved under the PE film. The use of the HOB film prevented almost all of the silage in the upper layer from spoiling; only 2 out of 32 samples had a mold count >6log10 cfu/g. This led to a net economic gain when the HOB film was used on both farms due to the increased DM recovery and reduced labor time required to clean the upper layer, even though the HOB film cost about 2.3 times more than the PE film. Furthermore, use of the HOB film, which ensures a longer shelf life of silage during consumption, reduced the detrimental effect of yeasts, molds, and aerobic and anaerobic spore-formers on the nutritional and microbiological quality of the unloaded silage.

  20. Application of Transportation Process of Mountain Tower Silos in Mining%山体圆筒仓运输工艺在矿山的应用

    Institute of Scientific and Technical Information of China (English)

    冯丽平

    2013-01-01

    According to the form of silos, the article puts forward the design idea of mountain tower silos and transportation technology, better solves the transportation of coal in mountain coal mine. The operation practice shows that the system is stable and reliable.%根据圆筒仓形式,提出了山体圆筒仓及运输工艺设计的思路,较好地解决了在山区矿井的煤炭外运问题.多年来的运行实践表明,系统是稳定可靠的.

  1. Efficacy and Safety of Calcipotriol Plus Betamethasone Dipropionate Aerosol Foam Compared with Betamethasone 17-Valerate-Medicated Plaster for the Treatment of Psoriasis.

    Science.gov (United States)

    Queille-Roussel, Catherine; Rosen, Monika; Clonier, Fabrice; Nørremark, Kasper; Lacour, Jean-Philippe

    2017-04-01

    Fixed combination calcipotriol as hydrate (Cal) 50 µg/g plus betamethasone as dipropionate (BD) 0.5 mg/g aerosol foam is an alcohol-free treatment for psoriasis. Betamethasone 17-valerate 2.25 mg (BV)-medicated plasters are recommended for treating psoriasis plaques localized in difficult-to-treat (DTT; elbow, knee, anterior face of the tibia) areas. The aim of this study was to compare the efficacy of Cal/BD foam with BV-medicated plaster in patients with plaque psoriasis. In this phase IIa, randomized, single-center, investigator-blinded, 4-week study, both Cal/BD foam and BV-medicated plaster were applied once daily to six test sites (three for each treatment). The primary efficacy endpoint was absolute change in total clinical score (TCS; sum of erythema, scaling, and infiltration); secondary endpoints were changes from baseline in each individual clinical score, ultrasonographic changes (total skin and echo-poor band thickness), and safety; and post hoc analysis was change from baseline in TCS on DTT areas. Thirty-five patients were included. Least-squares mean change in TCS from baseline was significantly greater for Cal/BD foam (-5.8) than BV-medicated plaster (-3.7; difference -2.2; 95% confidence interval -2.6 to -1.8; p plaster (both p plaster on DTT areas after 4 weeks (p plasters, including on DTT areas, in patients with plaque psoriasis. NCT02518048.

  2. 新型圆形陈化库及应用%A new kind of cylindrical ageing silo

    Institute of Scientific and Technical Information of China (English)

    2013-01-01

      介绍了新开发的圆形陈化库,主要由库体、布料机构、卸料机构及料位检测器等部分组成,彻底解决了传统陈化库物料水分易蒸发,布料不均匀,无法做到先进先出,扬尘不易收集处理等问题,可充分保证砖瓦生产企业的原料陈化效果。%A new kind of cylindrical ageing silo is introduced, which consists of the base body, distributing mechanism, discharge mechanism and material level detector. It solves the problems of material easy to moisture evaporation, uneven material distribution, unable to realize FIFO, not easy to collect and treat the dust of traditional silo, and guarantee the ageing effect of the raw materials.

  3. Discharge flow of a granular media from a silo: effect of the packing fraction and of the hopper angle

    Science.gov (United States)

    Benyamine, Mebirika; Aussillous, Pascale; Dalloz-Dubrujeaud, Blanche

    2017-06-01

    Silos are widely used in the industry. While empirical predictions of the flow rate, based on scaling laws, have existed for more than a century (Hagen 1852, translated in [1] - Beverloo et al. [2]), recent advances have be made on the understanding of the control parameters of the flow. In particular, using continuous modeling together with a mu(I) granular rheology seem to be successful in predicting the flow rate for large numbers of beads at the aperture (Staron et al.[3], [4]). Moreover Janda et al.[5] have shown that the packing fraction at the outlet plays an important role when the number of beads at the apeture decreases. Based on these considerations, we have studied experimentally the discharge flow of a granular media from a rectangular silo. We have varied two main parameters: the angle of the hopper, and the bulk packing fraction of the granular material by using bidisperse mixtures. We propose a simple physical model to describe the effect of these parameters, considering a continuous granular media with a dilatancy law at the outlet. This model predicts well the dependance of the flow rate on the hopper angle as well as the dependance of the flow rate on the fine mass fraction of a bidisperse mixture.

  4. ELEMENTOS PRÉ-MOLDADOS DE CONCRETO ARMADO, PARA SILOS QUADRADOS VERTICAIS, MODULARES, PARA ARMAZENAMENTO DE GRÃOS

    Directory of Open Access Journals (Sweden)

    Eduardo Teixeira da Silva

    1998-12-01

    Full Text Available RESUMO Este trabalho foi desenvolvido com o objetivo de fornecer subsídios técnicos para projetos de silos multicelulares em concreto armado, pré-moldados, com forma quadrada, para atender a pequenos e médios produtores, com capacidade de 60t, sendo 15t de milho por célula. Foram realizadas análises teóricas e experimentais em um modelo de elemento construtivo a fim de se avaliar o comportamento estrutural do elemento isolado e do encaixado, em escala natural, que formaram as paredes de silos quadrados modulares. Com base nas análises experimentais realizadas, concluiu-se que o modelo de encaixe utilizado entre dois elementos (tipo macho-fêmea comportou-se de maneira positiva, conferindo maior rigidez à região entre os elementos. As tensões calculadas pelo método simplificado Ravenet (1992 e teoria de vigas bi-articuladas, subestimam as tensões experimentais. Os deslocamentos medidos apresentam comportamento similar, porém superiores aos deslocamentos calculados pela flecha máxima e flecha no meio do vão.

  5. Control of quality and silo storage of sunflower seeds using near infrared technology

    Directory of Open Access Journals (Sweden)

    González-Martín, I.

    2013-03-01

    Full Text Available This work assesses the application of near infrared spectroscopy technology for the quality control of sunflower seeds direct from farmers and from a storage silo. The results show that the analytical method employing near infrared spectroscopy can be used as a rapid and non-destructive tool for the determination of moisture, fat and high/low oleic acid contents in samples of sunflower seeds. The ranges obtained were comparable to those reported for classic chemical methods, and were between 4.6-21.4% for moisture; 38.4-49.6% for fat, and 60.0-93.1% for oleic acid expressed as percentage of total fatty acids. A stepwise discriminant analysis was performed to determine the most useful wavelengths for classifying sunflower seeds in terms of their (high/low oleic acid composition. The discriminant model allows the classification of sunflower seeds with high or low oleic acid contents, with a prediction rate of 90.5% for internal validation and of 89.4% for cross-validation.

    En este trabajo se evalúa la espectroscopía de infrarrojo cercano para su uso en el control de calidad y almacenamiento de semillas de girasol. Los resultados indican que el método analítico empleado puede utilizarse como método de determinación rápida de humedad, grasa y contenidos altos/bajos de ácido oleico. Los rangos de aplicación son comparables con los valores que se han determinado mediante métodos clásicos de análisis, encontrándose entre 4.6-21.4% la humedad, 38.4-49.6% la grasa y 60.0- 93.1% de ácido oleico del total de los ácidos grasos. Además se ha utilizado un análisis discriminarte lineal por pasos determinando las longitudes de onda más adecuadas para la clasificación de semillas de girasol en los grupos alto/bajo oleico. El modelo generado permitió la clasificación de semillas de girasol en los grupos alto y bajo oleico con unos porcentajes de muestras correctamente clasificadas de un 90.5% en validación interna y de un 89.4% en

  6. Topical 5% lidocaine (lignocaine) medicated plaster treatment for post-herpetic neuralgia: results of a double-blind, placebo-controlled, multinational efficacy and safety trial.

    Science.gov (United States)

    Binder, Andreas; Bruxelle, Jean; Rogers, Peter; Hans, Guy; Bösl, Irmgard; Baron, Ralf

    2009-01-01

    Post-herpetic neuralgia (PHN) is a distressing neuropathic pain condition mainly affecting elderly patients. Neuropathic pain symptoms can be of a burning, shooting and stabbing nature, and may continue for prolonged periods and are often poorly controlled by polymedication. The aim of this study was to evaluate the analgesic efficacy and safety of topical analgesic treatment (5% lidocaine [lignocaine] medicated plaster) compared with placebo plaster in patients with PHN. This was a double-blind, placebo plaster-controlled, parallel-group, multicentre study employing enriched enrolment with randomized withdrawal methodology. After an initial 8-week open-label, active run-in phase, responders entered a 2-week randomized, double-blind, placebo-controlled phase. The study was conducted at 33 outpatient investigational centres in 12 European countries. Patients with PHN were selected who were aged >/=50 years, had experienced neuropathic pain persisting for >/=3 months after rash healing, and had a mean pain intensity of >/=4 on an 11-point numerical rating scale. A total of 265 patients entered the open-label phase and subsequently a pre-defined number of 71 patients entered the randomized phase. Patients applied up to three 5% lidocaine medicated plasters for up to 12 hours per day. The primary endpoint of the study was time-to-exit due to a >/=2-point reduction in pain relief on two consecutive days of plaster application using a 6-point verbal rating scale. Of the 265 patients entering the run-in phase, 51.7% achieved at least moderate pain relief. In the double-blind phase (full analysis set, n = 71), median times-to-exit were 13.5 (range 2-14) and 9.0 (range 1-14) days for lidocaine and placebo plaster groups, respectively (p = 0.151). For per-protocol patients (n = 34), median time-to-exit was 14.0 (range 3-14) and 6.0 (range 1-14) days for lidocaine and placebo plaster groups, respectively (p = 0.0398). Drug-related adverse events occurred in 13.6% of patients

  7. Rapid prototyping of a complex model for the manufacture of plaster molds for slip casting ceramic

    Directory of Open Access Journals (Sweden)

    D. P. C. Velazco

    2014-12-01

    Full Text Available Computer assisted designing (CAD is well known for several decades and employed for ceramic manufacturing almost since the beginning, but usually employed in the first part of the projectual ideation processes, neither in the prototyping nor in the manufacturing stages. The rapid prototyping machines, also known as 3D printers, have the capacity to produce in a few hours real pieces using plastic materials of high resistance, with great precision and similarity with respect to the original, based on unprecedented digital models produced by means of modeling with specific design software or from the digitalization of existing parts using the so-called 3D scanners. The main objective of the work is to develop the methodology used in the entire process of building a part in ceramics from the interrelationship between traditional techniques and new technologies for the manufacture of prototypes. And to take advantage of the benefits that allow us this new reproduction technology. The experience was based on the generation of a complex piece, in digital format, which served as the model. A regular 15 cm icosahedron presented features complex enough not to advise the production of the model by means of the traditional techniques of ceramics (manual or mechanical. From this digital model, a plaster mold was made in the traditional way in order to slip cast clay based slurries, freely dried in air and fired and glazed in the traditional way. This experience has shown the working hypothesis and opens up the possibility of new lines of work to academic and technological levels that will be explored in the near future. This technology provides a wide range of options to address the formal aspect of a part to be performed for the field of design, architecture, industrial design, the traditional pottery, ceramic art, etc., which allow you to amplify the formal possibilities, save time and therefore costs when drafting the necessary and appropriate matrixes

  8. Multi-technique investigation of Roman decorated plasters from Villa dei Quintili (Rome, Italy)

    Energy Technology Data Exchange (ETDEWEB)

    Crupi, Vincenza, E-mail: vcrupi@unime.it [Dipartimento di Fisica e di Scienze della Terra, Università degli Studi di Messina, Viale Ferdinando Stagno d’Alcontres 31, 98166 Messina (Italy); Galli, Giuliana [Soprintendenza Speciale per i Beni Archeologici di Roma, Villa dei Quintili, via Appia Nuova 1092, 00197 Roma (Italy); La Russa, Mauro Francesco [Dipartimento di Biologia, Ecologia e Scienze della Terra (DiBEST), Università degli Studi della Calabria, Via Pietro Bucci, 87036 Arcavacata di Rende (Cs) (Italy); Longo, Francesca; Maisano, Giacomo; Majolino, Domenico [Dipartimento di Fisica e di Scienze della Terra, Università degli Studi di Messina, Viale Ferdinando Stagno d’Alcontres 31, 98166 Messina (Italy); Malagodi, Marco [Dipartimento di Chimica, Università di Pavia, Via Taramelli 12, 27100 Pavia (Italy); Pezzino, Antonino [Dipartimento di Scienze Biologiche, Geologiche e Ambientali—Sezione di Scienze della Terra, Università degli Studi di Catania, Corso Italia 57, 95129 Catania (Italy); Ricca, Michela [Dipartimento di Biologia, Ecologia e Scienze della Terra (DiBEST), Università degli Studi della Calabria, Via Pietro Bucci, 87036 Arcavacata di Rende (Cs) (Italy); Rossi, Barbara [Elettra – Sincrotrone Trieste, Strada Statale 14 km 163.5, Area Science 70 Park, 34149 Trieste (Italy); Dipartimento di Fisica, Università degli Studi di Trento, via Sommarive 14, 38123 Povo, Trento (Italy); Ruffolo, Silvestro Antonio [Dipartimento di Biologia, Ecologia e Scienze della Terra (DiBEST), Università degli Studi della Calabria, Via Pietro Bucci, 87036 Arcavacata di Rende (Cs) (Italy); and others

    2015-09-15

    Highlights: • A multi-technique non-invasive approach using portable instrumentation is proposed. • Due to the use of different techniques, pigments of same color were distinguished. • The experimental results shed light on the used painting methodologies. • The experimental results provided useful information for restoration processes. • This work is the first study of coloring matter used in Villa dei Quintili. - Abstract: In the present study, we investigated by the joint use of portable instrumentations, namely a handheld X-ray fluorescence (XRF) analyser and a portable Raman spectrometer, the painted surface of plasters withdrawn from different areas of an important Roman monumental complex, known as Villa dei Quintili (Rome, Italy), dated back to the first half of the 2nd century a.C. XRF and Raman measurements contributed to the identification of the pigments through the elemental and molecular composition, respectively. In particular, the multi-technique non-invasive approach proved to be crucial for distinguishing two different reddish pigments. In order to confirm and integrate XRF and Raman results, two micro-destructive laboratory methods, namely optical microscopy (OM) and scanning electron microscopy coupled with energy-dispersive X-ray spectrometry (SEM-EDS), were also employed on the same samples. All the experimental results shed light on the material characterizing the painted surface layer and the painting methodologies, providing in principle useful information for proper restoration processes. It is worth underlining that this experimental investigation takes part of a recent multidisciplinary study performed on this impressive archaeological site, aimed to characterize for the first time the monumental complex from an archaeometric point of view.

  9. Laser cleaning experiences on sculptures' materials: terracotta, plaster, wood, and wax

    Science.gov (United States)

    Pelosi, Claudia; Fodaro, D.; Sforzini, Livia; Lo Monaco, Angela

    2013-11-01

    The focus of this paper is to show the work experiences with laser cleaning on sculptures made of terracotta, plaster, wood and wax. These materials exhibit peculiar features that often prevent the use of traditional cleaning procedures to remove the surface dirt, soot or carbonaceous deposits and other materials coming from environment or ancient conservative interventions. To overcome the difficulties in the cleaning of the above mentioned materials, laser technology was tested. The laser irradiation and cleaning tests were carried out with a Q-switched Nd:YAG system under the following conditions: wavelength 1064 nm and 532 nm; energy 4-28 mJ; pulse duration 10 ns; spot diameter 2-8 mm; frequency 5 Hz. The irradiated surfaces were analyzed before and after the laser tests, with the aid of a video microscope and a reflectance spectrophotometer, in order to evaluate the morphology and colour changes of the surfaces. Before starting with the cleaning intervention, some diagnostic analysis was performed on the sculptures in order to obtain the identification of the original materials and of the surface deposits. Concerning this, Fourier Transform Infrared spectroscopy, X-ray fluorescence spectroscopy, and internal micro stratigraphic analysis were performed. This research demonstrated that the laser cleaning is an effective method to remove the surface deposits preserving the original patina of the sculptures and the opacity of the wax. The results gathered in this work encourage to continue the research in order to better understand the interactions between the laser beam and the surfaces and to find the most appropriate laser conditions to clean the sculptures.

  10. 中欧钢筋混凝土筒仓设计规范比较%Comparison of concrete silo design standard of China and Europe

    Institute of Scientific and Technical Information of China (English)

    祝振兴; 朱建平; 曹勇; 吴宏; 王振波; 张红松

    2013-01-01

    By real project case, Eurocode(Eurocode 1-Actions on structures-Part 4:Silos and tanks)(EN 1991-4:2006)and China standard《Code for design of reinforced concrete silos》(EN 1991-4:2006)were contrasted in calculation of the horizontal pressure,verti-cal pressure and friction of silo wall. Wish it can guide the silo design.%  通过实际工程案例,对比分析采用欧洲规范《Eurocode 1-Actions on structures-Part 4:Silos and tanks》(EN 1991-4:2006)和中国规范《钢筋混凝土筒仓设计规范》(GB 50077-2003)计算钢筋混凝土筒仓结构时,贮料水平压力、竖向压力、仓壁上单位周长上总摩擦力的差别,以期指导工程设计。

  11. The Reclaim Screw in Mammoth Silos Operating on a Free Surface: Comparison Between Horizontal and Inclined Operation on Free Flowing Bulk Solids

    NARCIS (Netherlands)

    Oosterhuis, Ekke; Schott, Dingena; Wijk, van Arjen

    2004-01-01

    Although the screw conveyor, operating on a free surface, has been used for years as reclaim and storage equipment in mammoth silos, there is no documented knowledge about its spill characteristics. Research at Delft University of Technology together with ESI Eurosilo B.V. on the inclined use of the

  12. Efeitos da adição de inoculantes microbianos sobre a composição bromatológica e perfil fermentativo da silagem de sorgo produzida em silos experimentais Effects of microbial inoculants on chemical composition and fermentation characteristics of sorghum silage

    Directory of Open Access Journals (Sweden)

    Paulo Henrique Mazza Rodrigues

    2002-11-01

    Full Text Available Foram estudados os efeitos de três inoculantes microbianos, na silagem de sorgo (Agroceres 2005, em 16 silos experimentais, confeccionados a partir de baldes plásticos portando válvulas. O sorgo, cortado aos 97 dias de crescimento (35,9% de MS, foi homogeneizado e submetido a quatro tratamentos, com quatro repetições: controle, Sil-All (Streptococcus faecium, Pediococcus acidilactici, Lactobacillus plantarum, amilase, hemicelulase e celulase, Silobac (L. plantarum, S. faecium e Lactobacillus sp e Pioneer 1174 (S. faecium e L. plantarum. Os silos foram abertos após 120 dias para análise da composição bromatológica e perfil fermentativo. Os três inoculantes diminuíram o teor de MS e aumentaram a concentração de etanol e as perdas de MS, em relação ao grupo controle. O Sil-All aumentou o teor de FDN, em relação ao grupo controle, e diminuiu a concentração de amido, em relação ao Silobac, enquanto que o Pioneer 1174 diminuiu a estabilidade aeróbia, em relação ao grupo controle. Não foram observados efeitos sobre os teores de PB, NIDA, carboidratos solúveis, FDA, lignina, hemicelulose, celulose, a digestibilidade in vitro da matéria seca, o poder tampão e as concentrações dos ácidos acético, propiônico, butírico e lático, bem como sobre o pH ou sobre as concentrações de nitrogênio amoniacal.Sorghum Agroceres 2005 (35.9% DM was ensiled in 16 plastic experimental silos, forming four treatments: control, Sil-All (Streptococcus faecium, Pediococcus acidilactici, Lactobacillus plantarum, amylase, hemicellulase, and cellulase, Silobac (L. plantarum, S. faecium, and Lactobacillus sp, and Pioneer 1174 (S. faecium and L. plantarum. Silos were opened 120 days after ensiling and silage was sampled to proceed chemical analyses. Sil-All, Silobac and Pioneer decreased dry matter content and increased ethylic alcohol concentration and DM losses compared to control. Sil-All increased NDF content compared to control and

  13. Early mobilisation versus plaster immobilisation of simple elbow dislocations: results of the FuncSiE multicentre randomised clinical trial.

    Science.gov (United States)

    Iordens, Gijs I T; Van Lieshout, Esther M M; Schep, Niels W L; De Haan, Jeroen; Tuinebreijer, Wim E; Eygendaal, Denise; Van Beeck, Ed; Patka, Peter; Verhofstad, Michael H J; Den Hartog, Dennis

    2017-03-01

    To compare outcome of early mobilisation and plaster immobilisation in patients with a simple elbow dislocation. We hypothesised that early mobilisation would result in earlier functional recovery. From August 2009 to September 2012, 100 adult patients with a simple elbow dislocation were enrolled in this multicentre randomised controlled trial. Patients were randomised to early mobilisation (n=48) or 3 weeks plaster immobilisation (n=52). Primary outcome measure was the Quick Disabilities of the Arm, Shoulder, and Hand (Quick-DASH) score. Secondary outcomes were the Oxford Elbow Score, Mayo Elbow Performance Index, pain, range of motion, complications and activity resumption. Patients were followed for 1 year. Quick-DASH scores at 1 year were 4.0 (95% CI 0.9 to 7.1) points in the early mobilisation group versus 4.2 (95% CI 1.2 to 7.2) in the plaster immobilisation group. At 6 weeks, early mobilised patients reported less disability (Quick-DASH 12 (95% CI 9 to 15) points vs 19 (95% CI 16 to 22); p<0.05) and had a larger arc of flexion and extension (121° (95% CI 115° to 127°) vs 102° (95% CI 96° to 108°); p<0.05). Patients returned to work sooner after early mobilisation (10 vs 18 days; p=0.020). Complications occurred in 12 patients; this was unrelated to treatment. No recurrent dislocations occurred. Early active mobilisation is a safe and effective treatment for simple elbow dislocations. Patients recovered faster and returned to work earlier without increasing the complication rate. No evidence was found supporting treatment benefit at 1 year. NTR 2025. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

  14. Building a diagnostic algorithm on localized neuropathic pain (LNP) and targeted topical treatment: focus on 5% lidocaine-medicated plaster

    Science.gov (United States)

    Casale, Roberto; Mattia, Consalvo

    2014-01-01

    Within the broad definition of neuropathic pain, the refinement of clinical diagnostic procedures has led to the introduction of the concept of localized neuropathic pain (LNP). It is characterized by consistent and circumscribed area(s) of maximum pain, which are associated with negative or positive sensory signs and/or spontaneous symptoms typical of neuropathic pain. This description outlines the clinical features (currently lacking in guidelines and treatment recommendations) in patients for whom topical targeted treatment with 5% lidocaine-medicated plaster is suggested as first-line therapy. Few epidemiologic data are present in the literature but it is generally estimated that about 60% of neuropathic pain conditions are localized, and therefore identifiable as LNP. A mandatory clinical criterion for the diagnosis of LNP is that signs and symptoms must be present in a clearly identified and defined area(s). Cartographic recordings can help to define each area and to assess variations. The diagnosis of LNP relies on careful neurological examination more than on pain questionnaires, but it is recognized that they can be extremely useful for recording the symptom profiles and establishing a more targeted treatment. The most widely studied frequent/relevant clinical presentations of LNP are postherpetic neuralgia, diabetic neuropathy, and neuropathic postoperative pain. They successfully respond to treatment with 5% lidocaine-medicated plaster with equal if not better pain control but with fewer side effects versus conventional systemic treatments. Generally, the more localized the pain (ie, the area of an A4 sheet of paper) the better the results of topical treatment. This paper proposes an easy-to-understand algorithm to identify patients with LNP and to guide targeted topical treatments with 5% lidocaine medicated plaster. PMID:24790451

  15. Solid phase microextraction, sand flies, oviposition pheromones, plaster of Paris and siloxanes-What is in common?

    Science.gov (United States)

    Goulart, Thais Marchi; Tosta, Christiann Davis; Machado, Vicente Estevam; da Rocha Silva, Flávia Benini; de Castro, Camila Feitosa; Ortiz, Dennys Ghenry Samillan; Oliveira, Wanderson Henrique Cruz; Pinto, Mara Cristina

    2017-04-01

    Sand flies are natural hosts of various microorganisms. Due to their epidemiological importance, sand fly colonies are kept in laboratories to be studied in terms of their biology and vector/host/parasite interactions. In order to investigate the presence of oviposition pheromones in Nyssomyia neivai, experiments using Solid Phase Microextraction (SPME) were performed. However, siloxanes which is an external class of contamination, present in breeding containers made by plaster used to maintain sand flies in colonies, may be hindered the experiments. Published by Elsevier B.V.

  16. Characterization of the Minimum Effective Layer of Thermal Insulation Material Tow-plaster from the Method of Thermal Impedance

    Directory of Open Access Journals (Sweden)

    M.S. Ould Brahim

    2011-04-01

    Full Text Available Our objective in this study is to determine the effective thermal insulating layer of a composite towplaster. The characterization of thermal insulating material is proposed from the study of the thermal impedance in dynamic two-dimensional frequency. Thermo physical properties of the material tow-plaster are determined from the study of the thermal impedance. Nyquist representations have introduced an interpretation of certain phenomena of heat transfer from the series and shunt resistors. The overall coefficient of heat exchange is determined from the Bode plots. A method for determining the thermal conductivity is proposed.

  17. Assessing agreement in measurements of orthodontic study models: Digital caliper on plaster models vs 3-dimensional software on models scanned by structured-light scanner.

    Science.gov (United States)

    Wan Hassan, Wan Nurazreena; Othman, Siti Adibah; Chan, Chee Seng; Ahmad, Roshahida; Ali, Siti Nor'Ain; Abd Rohim, Anis

    2016-11-01

    In this study we aimed to compare measurements on plaster models using a digital caliper, and on 3-dimensional (3D) digital models, produced using a structured-light scanner, using 3D software. Fifty digital models were scanned from the same plaster models. Arch and tooth size measurements were made by 2 operators, twice. Calibration was done on 10 sets of models and checked using the Pearson correlation coefficient. Data were analyzed by error variances, repeatability coefficient, repeated-measures analysis of variance, and Bland-Altman plots. Error variances ranged between 0.001 and 0.044 mm for the digital caliper method, and between 0.002 and 0.054 mm for the 3D software method. Repeated-measures analysis of variance showed small but statistically significant differences (P plaster models and were, therefore, clinically acceptable. Copyright © 2016. Published by Elsevier Inc.

  18. Aplicación de la norma EN 14491:2006 a los silos de acero cilíndricos para la protección frente a explosiones de polvo

    Directory of Open Access Journals (Sweden)

    Tascón, A.

    2012-06-01

    Full Text Available Dust explosions represent a serious hazard in industries and silo facilities that handle combustible materials. Venting devices are commonly used to try to mitigate the damage caused by any dust explosion. To calculate vent area size, the recommendations given in European standard EN 14491:2006 can be used. However, the protection of silos is not always simple, and frequently the installation of vents becomes technically difficult and costly. The aim of the present work was to analyse the application of standard EN 14491:2006 to cylindrical steel silos, remarking the existing difficulties and limitations and explaining some critical points in order to understand the aforementioned standard. In addition, the cost of protection by venting in silos was studied. Finally, the authors have provided some suggestions to solve the protection of silos, alternative methods to calculate vent areas and expected future trends in this field.

    Las explosiones de polvo representan un serio peligro en aquellas industrias y silos en los que se manejan materiales combustibles. Para mitigar los efectos de una posible explosión generalmente se utilizan dispositivos de venteo, que pueden dimensionarse siguiendo la norma europea EN 14491:2006. Sin embargo, frecuentemente surgen complicaciones que hacen que la instalación de venteos sea técnicamente complicada y muy costosa. El objetivo de este trabajo fue analizar la aplicación de la norma EN 14491:2006 a los silos metálicos cilíndricos, remarcando las dificultades y limitaciones existentes y explicando sus aspectos clave para poder aplicarla correctamente. También se ha calculado el coste que puede suponer la protección de silos mediante venteos. Finalmente, se proporcionan algunas sugerencias para afrontar la protección de silos, información sobre métodos alternativos de cálculo de venteos y tendencias de futuro en este campo.

  19. Hearing loss

    Science.gov (United States)

    Decreased hearing; Deafness; Loss of hearing; Conductive hearing loss; Sensorineural hearing loss; Presbycusis ... Symptoms of hearing loss may include: Certain sounds seeming too ... conversations when two or more people are talking Difficulty ...

  20. Alterações químicas e microbiológicas nas silagens de capim-Tifton 85 após a abertura dos silos Chemical and microbiological changes of Tifton 85 grass silage after silos opening

    Directory of Open Access Journals (Sweden)

    Rúben Pablo Schocken-Iturrino

    2005-04-01

    Full Text Available O trabalho foi conduzido para avaliação da presença de Listeria sp. e de fungos nas silagens de capim-Tifton 85 sem emurchecimento, com emurchecimento por uma e duas horas e sem emurchecimento com adição ou não de polpa cítrica (5,0% do peso verde. As amostragens foram efetuadas no momento da abertura do silo (80 dias da ensilagem, aos 15 e 30 dias após exposição ao ar, para avaliar os teores de matéria seca (MS, as alterações químicas (pH, N amoniacal, ácidos orgânicos e a ocorrência de Listeria sp. e de fungos. Os dados foram analisados segundo o delineamento em blocos casualizados, em esquema de parcelas subdivididas (nas parcelas foram avaliadas as silagens submetidas aos tratamentos e nas subparcelas, os períodos de exposição ao ar, com quatro repetições. Observaram-se baixos teores de ácidos orgânicos e de N amoniacal decorrentes dos altos valores de MS, o que acarretou baixa formação de produtos fermentados e elevação do pH. A presença de Listeria sp. foi observada em 65,6% das amostras no momento da abertura dos silos e, destas, 10% foram positivas para Listeria monocytogenes. As silagens apresentaram baixa estabilidade aeróbia, tendo sido registrado aumento na ocorrência dos fungos Penicillium, Fusarium e Pithomyces com o prolongamento do período de exposição ao ar.The experiment was carried out to evaluate the fermentation characteristics, Listeria sp. and molds occurrence on Tifton 85 silage no wilted, wilted for one and two hours and no wilted with or without citrus pulp (5.0 % of fresh forage. The samplings were taken at the opening of the silos (80 days after ensiling, 15, and 30 days after air exposition to evaluated dry matter (DM content, chemical changes (pH, ammonia N, organic acids and Listeria sp., and molds occurrence. Data were analyzed according to a randomized block design in split plot scheme, considering the silage on the plots, and periods of air exposure on the split plot, with four

  1. Advice about the safety of graphite storage silos of Saint Laurent des Eaux facility; Avis sur la surete des silos de stockage de graphite de Saint Laurent des Eaux

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2005-07-01

    This document is the safety analysis made by the national association of the local commissions of information about nuclear activities (ANCLI), about the safety of graphite storage silos of Saint Laurent des Eaux nuclear facility. The analysis covers: the operation safety and the accident hypothesis, the monitoring of indoor and outdoor contamination in routine situation, the geotechnical characteristics of the site environment, the isotopic inventory and the estimation of radioactivity in routine and accidental situation, the estimation of doses received by the population in accidental situation and the internal emergency plan. After examination of these different points, the scientific committee of the ANCLI considers that a new global evaluation of risks, which integrates more recent exposure data, has to be carried out. (J.S.)

  2. Analysis of wall plasters and natural sediments from the Neolithic town of Çatalhöyük (Turkey) by a range of analytical techniques

    Science.gov (United States)

    Anderson, Emma; Almond, Matthew J.; Matthews, Wendy

    2014-12-01

    Wall plaster sequences from the Neolithic town of Çatalhöyük have been analysed and compared to three types of natural sediment found in the vicinity of the site, using a range of analytical techniques. Block samples containing the plaster sequences were removed from the walls of several different buildings on the East Mound. Sub-samples were examined by IR spectroscopy, X-ray diffraction and X-ray fluorescence to determine the overall mineralogical and elemental composition, whilst thin sections were studied using optical polarising microscopy, IR Microscopy and Environmental Scanning Electron Microscopy with Energy Dispersive X-ray analysis. The results of this study have shown that there are two types of wall plaster found in the sequences and that the sediments used to produce these were obtained from at least two distinct sources. In particular, the presence of clay, calcite and magnesian calcite in the foundation plasters suggested that these were prepared predominantly from a marl source. On the other hand, the finishing plasters were found to contain dolomite with a small amount of clay and no calcite, revealing that softlime was used in their preparation. Whilst marl is located directly below and around Çatalhöyük, the nearest source of softlime is 6.5 km away, an indication that the latter was important to the Neolithic people, possibly due to the whiter colour (5Y 8/1) of this sediment. Furthermore, the same two plaster types were found on each wall of Building 49, the main building studied in this research, and in all five buildings investigated, suggesting that the use of these sources was an established practice for the inhabitants of several different households across the site.

  3. Reduction of painful area as new possible therapeutic target in post-herpetic neuropathic pain treated with 5% lidocaine medicated plaster: a case series.

    Science.gov (United States)

    Casale, Roberto; Di Matteo, Maria; Minella, Cristina E; Fanelli, Guido; Allegri, Massimo

    2014-01-01

    Post-herpetic neuralgia (PHN) is neuropathic pain persisting after an acute episode of herpes zoster, and is associated with severe pain and sensory abnormalities that adversely affect the patient's quality of life and increase health care costs. Up to 83% of patients with PHN describe localized neuropathic pain, defined as "a type of neuropathic pain characterized by consistent and circumscribed area(s) of maximum pain". Topical treatments have been suggested as a first-line treatment for localized neuropathic pain. Use of 5% lidocaine medicated plaster could reduce abnormal nervous peripheral discharge and via the plaster could have a "protective" function in the affected area. It has been suggested that use of this plaster could reduce pain as well as the size of the painful area. To evaluate this possible outcome, we retrospectively reviewed eight patients with PHN, treated using 5% lidocaine medicated plaster. During a follow-up period of 3 months, we observed good pain relief, which was associated with a 46% reduction in size of the painful area after one month (from 236.38±140.34 cm(2) to 128.80±95.7 cm(2)) and a 66% reduction after 3 months (81.38±59.19 cm(2)). Our study cohort was composed mainly of elderly patients taking multiple drugs to treat comorbidities, who have a high risk of drug-drug interactions. Such patients benefit greatly from topical treatment of PHN. Our observations confirm the effectiveness of lidocaine plasters in the treatment of PHN, indicating that 5% lidocaine medicated plaster could reduce the size of the painful area. This last observation has to be confirmed and the mechanisms clarified in appropriate larger randomized controlled trials.

  4. Efficacy and tolerability of DHEP-heparin plaster in reducing pain in mild-to-moderate muscle contusions: a double-blind, randomized trial.

    Science.gov (United States)

    Hoffmann, Peter; Kopačka, Pavel; Gugliotta, Barbara; Rovati, Stefano

    2012-08-01

    To investigate if the 180-mg diclofenac epolamine and heparin sodium 5600 IU medicated plaster (DHEP-heparin) is more effective for pain reduction in mild-to-moderate contusions than the reference diclofenac epolamine 180 mg plaster (DHEP). This multicenter, multinational, prospective, double-blind versus reference comparator and versus placebo, controlled trial had balanced random assignment in three parallel treatment groups. The DHEP-heparin medicated plaster was compared to the DHEP medicated plaster and a placebo medicated plaster. A total of 331 outpatients, aged ≥18 and ≤65 years, with unilateral mild-to-moderate muscle contusion, pain on standardized movement of ≥50 mm, and superficial hematoma of ≤10 × 14 cm(2) completed the study. Plasters were applied each morning, for ≥20 hours daily for 14 consecutive days. Outcomes were assessed in three visits, over 14 days, plus patients' daily self-assessment. 05DCz/FHp11 - Eudra CT n: 2005-003829-31 Primary efficacy endpoint was mean change from baseline in pain on movement after 3 days of treatment, compared between groups. Secondary efficacy endpoints included mean daily change from baseline in pain on movement during treatment, pain level as assessed at control visits after 7 and 14 days, time (days) to hematoma disappearance based on patients' daily evaluations, rescue medication use, and overall treatment efficacy as judged by both patients and investigators. Pain progressively declined in all groups, more rapidly in DHEP-heparin recipients, compared to DHEP, and in both active treatment groups compared to placebo. Adverse events were recorded in 24 of the 355 (6.7%) exposed patients, and generally resolved without need to interrupt treatment. The DHEP-heparin plaster is superior to the reference DHEP plaster in reducing pain associated with mild-to-moderate muscle contusion. Both active treatments were significantly more effective than placebo, and each showed a comparably favorable

  5. Expert voices for change: bridging the silos-towards healthy and sustainable settings for the 21st century.

    Science.gov (United States)

    Dooris, Mark

    2013-03-01

    The settings approach to health promotion, first advocated in the 1986 Ottawa Charter for Health Promotion, was introduced as an expression of the 'new public health', generating both acclaim and critical discourse. Reflecting an ecological model, a systems perspective and whole system thinking, the approach has been applied in a wide range of geographical and organisational contexts. This paper reports on a qualitative study undertaken through in-depth interviews with key individuals widely acknowledged to have been the architects and pilots of the settings movement. Exploring the development of the settings approach, policy and practice integration, and connectedness 'outwards', 'upwards' and 'beyond health', it concludes that the settings approach has much to offer-but will only realise its potential impact on the wellbeing of people, places and the planet if it builds bridges between silos and reconfigures itself for the globalised 21st century.

  6. Quantitative Determination of Aflatoxin by High Performance Liquid Chromatography in Wheat Silos in Golestan Province, North of Iran

    Science.gov (United States)

    NAMJOO, Mohadeseh; SALAMAT, Faezeh; RAJABLI, Niloofar; HAJIHOSEEINI, Reza; NIKNEJAD, Farhad; KOHSAR, Faramarz; JOSHAGHANI, Hamidreza

    2016-01-01

    Background: Aflatoxins are the most common mycotoxins that contaminate crops. They are produced by fungi such as Aspergillus flavus and Aspergillus parasiticus. Wheat (Tricitumaestivum) is one of the most important staple foods used in Iran, and the environmental conditions in the north of Iran are favorable to fungal growth. This study was designed in order to determine the aflatoxin concentration in wheat samples from silos in Golestan Province north of Iran. Methods: Samples were collected from three silos of Golestan province. First, aflatoxins were isolated using immunoaffinity chromatography. Then the aflatoxin concentrations were determined by High performance liquid chromatography (HPLC) method and fluorescence detector. Results: Ten out of 34 samples (29.4% of samples) were contaminated by aflatoxins.No concentration was found above permitted aflatoxin levels in Iran (15 ng/g). In one sample (2.9%), aflatoxin B1 was seen over the permissible limits in Iran. The highest level found in samples for total aflatoxin, aflatoxin B1, aflatoxin B2, aflatoxin G1 and aflatoxin G2 were 7.08 ng/g, 6.91 ng/g, 0.29 ng/g, 1.37 ng/g and 0.23 ng/g, respectively. No correlation was found between humidity levels in wheat samples contained aflatoxin and wheat samples without aflatoxin. Conclusion: Despite the total aflatoxins determined in samples were below the permissible limits in Iran, the 29% aflatoxin contamination rate can negatively affect health factors and it should not be neglected. So, it is predictable that if the storage duration of samples increases, the aflatoxin contamination levels will increase. PMID:27516997

  7. Modelling the mitigation of hydrogen deflagrations in a nuclear waste silo ullage by depleting the oxygen concentration with nitrogen

    Energy Technology Data Exchange (ETDEWEB)

    Holborn, P.G., E-mail: holborpg@lsbu.ac.uk; Battersby, P.; Ingram, J.M.; Averill, A.F.; Nolan, P.F.

    2013-10-15

    Highlights: • Examine the effect of reduced O{sub 2} on H{sub 2} burning velocity. • Model the effect of reduced oxygen level on overpressure for a transient H{sub 2} release. • Low O{sub 2} levels significantly reduce H{sub 2} burning velocity and explosion overpressure. -- Abstract: It is expected that significant transient releases of hydrogen could occur during the decommissioning of a nuclear waste storage plant that would result in a transient flammable atmosphere. Interest has been expressed in the use of nitrogen dilution in a vented silo ullage space in order to reduce the oxygen level and thereby mitigate the overpressure rise should a hydrogen–air deflagration occur. In the work presented here the data characterising the influence of oxygen depletion via nitrogen dilution upon the burning velocity of hydrogen–air mixtures have been obtained using the COSILAB code (and also compared with experimental test data). These data have then been used with the FLACS-HYDROGEN CFD-tool to try to predict the potential explosion overpressure reduction that might be achieved using oxygen depletion (via nitrogen dilution), for a transient hydrogen bubble sudden gaseous release (SGR) scenario occurring in a silo ullage type geometry. The simulation results suggest that using nitrogen dilution to deplete the oxygen levels to 12.5% or 9.9% would produce only a relatively modest reduction in the predicted peak overpressure. However, with an oxygen depletion level of 7%, the rate of pressure rise is more substantially slowed and the predicted maximum pressure rise is significantly reduced.

  8. A Literature Review of the Acupoint Plaster Therapy for Asthma in Summer

    Institute of Scientific and Technical Information of China (English)

    Kai Wang; Ya-Jun Du; Zeng-Tao Sun; Xiao-Juan Li; En-Shun Liu

    2016-01-01

    #摘要“冬病夏治”是对于冬季气候寒冷时好发的一些疾病,在夏季气温高时,给予温补阳气的综合治疗方法,属于中医时令医疗范畴。冬病夏治的理论源于《内经·素问》“天人合一”“春夏养阳”理论,孙思邈《备急千金要方》提出三伏时节内服药物治疗冬季好发疾病,《太平圣惠方》提出三伏天外治治疗冬季发作疾病。《本草纲目》提出根据季节选取治疗疾病的药物。《张氏医通·诸气门下喘》明确提出哮喘病冬病夏治三伏贴的代表方剂冷哮方。本研究则通过现代文献分析针对其组方配伍、作用机制等方面进一步深入研究。%Treating winter diseases in summer is characterized by warming Yang, which is recuperating in the summer, to treat some chronic diseases commonly seen in winter. This treatment belongs to the chronomedicine of TCM. This theory originates from Plain Questions, which puts forward the theory of the harmony of the human body and nature as well as the theory of maintaining Yang in spring and summer. In addition, Beiji Qianjin Yaofang puts forward the theory of treating winter diseases by taking oral medicine during dog days;Taiping Shenghui Fang puts forward the theory of treating winter diseases by using external medicine during dog days;choosing medicine according to season is proposed in Compendium of Materia Medica and Zhangshi Yitong puts forward using acupoint plaster therapy for treating asthma in midsummer. Based on meta-analysis reviews, current research has been focused on the mechanism, composition, and compatibility of the prescription.

  9. Effects of Panax ginseng-containing herbal plasters on compressed intervertebral discs in an in vivo rat tail model

    Directory of Open Access Journals (Sweden)

    Chow Daniel H K

    2013-02-01

    Full Text Available Abstract Background Tienchi (Panax notoginseng has been used in conservative treatments for back pain as a major ingredient of many herbal medicines. This study aims to investigate the effects of a herbal medicine containing tienchi on compressed intervertebral discs in rats. Methods Using an in vivo rat tail model, intervertebral disc compression was simulated in the caudal 8–9 discs of 25 rats by continuous static compression (11 N for 2 weeks. An herbal medicine plaster (in which the major ingredient was tienchi was externally applied to the compressed disc (n=9 for three weeks, and held in place by an adhesive bandage, in animals in the Chinese Medicine (CM group. The effect of the bandage was evaluated in a separate placebo group (n=9, while no intervention with unrestricted motion was provided to rats in an additional control group (n=7. Disc structural properties were quantified by in vivo disc height measurement and in vitro morphological analysis. Results Disc height decreased after the application of compression (P P = 0.006 and placebo (P = 0.003 groups, but was maintained in the CM group (P = 0.494. No obvious differences in disc morphology were observed among the three groups (P = 0.896. Conclusion The tienchi-containing herbal plaster had no significant effect on the morphology of compressed discs, but maintained disc height in rats.

  10. EXPERIENCE OF USING THE MONTE-CARLO METHOD IN DETERMINING OPTIMAL PLASTER COMPOSITIONS WITH IMPROVED STRENGTH PROPERTIES

    Directory of Open Access Journals (Sweden)

    Khrystyna Moskalova

    2017-01-01

    Full Text Available Considering that modern building materials impose increasing performance requirements, it is necessary to expand the range of building materials and improve their multicomponent composition. The effects of polymer and porous components (expanded perlite sand and carbonate filler – limestone-shell rock in cement-lime light plaster on the physico-mechanical properties of the mixtures under equal workability conditions of mixtures are analyzed based on experimental-statistical modeling. The results of the physico-mechanical and operational experiments confirm the rationality of using porous fillers and additives to improve certain specific properties of the final product. The so-called Monte-Carlo method is implemented for determining an optimal composition of multicomponent cement-lime light plaster, based on multivariate statistical modeling and iterative random scanning of property fields. According to the results of the computational experiment, a composition that reduces the number of expensive mixture components and improves the physical and mechanical characteristics of the resulting composition is selected.

  11. A prospective study of a modified pin-in-plaster technique for treatment of fractures of the distal radius.

    Science.gov (United States)

    Mirghasemi, S A; Rashidinia, S; Sadeghi, M S; Talebizadeh, M; Rahimi, N

    2015-11-01

    There are various pin-in-plaster methods for treating fractures of the distal radius. The purpose of this study is to introduce a modified technique of 'pin in plaster'. Fifty-four patients with fractures of the distal radius were followed for one year post-operatively. Patients were excluded if they had type B fractures according to AO classification, multiple injuries or pathological fractures, and were treated more than seven days after injury. Range of movement and functional results were evaluated at three and six months and one and two years post-operatively. Radiographic parameters including radial inclination, tilt, and height, were measured pre- and post-operatively. The average radial tilt was 10.6° of volar flexion and radial height was 10.2 mm at the sixth month post-operatively. Three cases of pin tract infection were recorded, all of which were treated successfully with oral antibiotics. There were no cases of pin loosening. A total of 73 patients underwent surgery, and three cases of radial nerve irritation were recorded at the time of cast removal. All radial nerve palsies resolved at the six-month follow-up. There were no cases of median nerve compression or carpal tunnel syndrome, and no cases of tendon injury. Our modified technique is effective to restore anatomic congruity and maintain reduction in fractures of the distal radius. Cite this article: Bone Joint Res 2015;4:176-180. ©2015 Mirghasemi et al.

  12. Location of quarries of magnesian lime used as raw material of Roman plasters in western Lombardy (Italy

    Directory of Open Access Journals (Sweden)

    Roberto Bugini

    2017-01-01

    Full Text Available Lime as building material was widely diffused in Roman architecture of western Lombardy. The presence of magnesite (magnesium carbonate was detected in painted plasters coming from roman sites of Milano: magnesite indicates the use of dolomite to make the lime. Dolomite rocks widely outcrop in the Lombard Prealps: light grey dolomites and dolomitic limestones (Dolomia del Salvatore, Ladinian-Anisian; grey dolomites, sometimes with cyclothemes (Dolomia Principale, Norian. There is no evidence of Roman lime quarries or kilns in this area; the Romans probably exploited the same dolomite outcrops, located along the eastern shore of lake Maggiore, where lime was produced from the Middle Ages onwards. The glacio-fluvial deposits of the middle course of the river Adda (cobbles, pebbles of siliceous limestone together with limestone and dolomite outcropping in the river basin were another medieval and modern source of raw material, mainly to make a moderately hydraulic lime (called “calce forte”, but this kind of lime is lacking in Roman plasters.

  13. 超大型储煤筒仓在煤炭装卸港口中的创新应用%Innovative application of extra-large coal silo in the loading and unloading port

    Institute of Scientific and Technical Information of China (English)

    张延军; 李刚; 许宁

    2012-01-01

    黄骅港三期工程中堆场采用了超大型筒仓储煤,介绍了筒仓流程和工艺,提出了筒仓安全运营面临的问题,着重介绍了储煤筒仓安全监测装置的选用和布置.%The extra-large coal silo is adopted in the storage yard of phase III project of Huanghua Port. The paper introduces the process and technology of such silo, proposes problems encountered during the silo operation, and emphasizes the selection and layout of the safety monitoring device for the coal silo.

  14. Effect of outlet diameter of cone-in-cone insert on silo flow pattern%锥形改流体下部孔径对筒仓卸料流态的影响

    Institute of Scientific and Technical Information of China (English)

    谭援强; 肖湘武; 郑军辉; 姜胜强; 高伟

    2016-01-01

    为了获取锥形改流体(cone-in-cone)下部孔径对筒仓内卸料流态和仓壁压力的影响,实现中心流筒仓内物料流态从中心流到整体流的转变,改善筒仓内物料流动环境,建立模型,用试验验证模型是正确的,该文采用离散元法对三维筒仓中ABS球卸料过程进行了数值模拟。数值模拟结果表明:筒仓卸料口尺寸不变时,减小锥形改流体下部孔径,整体流系数增大,筒仓内物料流态能够从中心流转变为整体流,筒仓壁峰值压力减小且峰值压力位置上移。改流体倾角为120°、135°时,当锥形改流体距筒仓锥形壁面的距离与锥形改流体下部孔径的比值大于等于1时,能实现从中心流到整体流的转变。该研究基于数值模拟结果提出了锥形改流体的设计标准,可为工程上确定改流体结构、位置参数提供参考。%In the food, chemical, pharmaceutical and other industrial engineering field, about 50% of the products and 75% of raw materials are usually stored in the form of particles in the silo. The silo flow pattern can be divided into the mass flow and the funnel flow. In the process of silo design, the mass flow pattern is preferred. With the appropriate presence of cone-in-cone insert, the funnel flow pattern can be changed into mass flow pattern in funnel flow silo. In order to understand the effect of structure and position parameters of cone-in-cone insert on the flow pattern and develop a theory model to design them properly, the discharging processes of acrylonitrile butadiene styrene copolymer (ABS) beads in scale-down funnel flow silo were simulated using the discrete element method (DEM). The validity of the DEM simulations was confirmed by comparing with the experimental results. Mass flow index (MFI) was used to judge silo flow pattern. Firstly, the effects of the height of cone-in-cone insert, the distance between outlet of cone-in-cone insert and discharge

  15. Discussion on improvement measures of large diameter raw silo coal appearance quality%超大直径原煤筒仓外观质量的改善措施探讨

    Institute of Scientific and Technical Information of China (English)

    朱晓丁

    2015-01-01

    Taking the technical renovation project of raw coal silo of coal preparation plant as an example, through the analysis on the causes in-fluence of silo quality problems, introduced the difficulties of silo in construction, combining with each difficult briefly discussed how to improve the appearance quality of raw coal silo, and gave specific implementation measures.%以选煤厂原煤筒仓技改工程为例,通过分析影响筒仓质量问题的原因,对该筒仓施工中的难点作了介绍,结合各难点问题对如何改进原煤筒仓的外观质量作了简要探讨,并给出了具体的实施对策。

  16. Stress Analysis and Strengthening Scheme for an Assemblage Grain Steel Silo with a Large Bin Gate%带大仓门装配式粮食钢板筒仓应力分析与增强方案

    Institute of Scientific and Technical Information of China (English)

    王振清; 尚豫才; 周春雷; 段军

    2012-01-01

    "Code for design of grain steel silos" (GB 50322-2001) and ANSYSTM were utilized to analysis stress for an assemblage steel silo with a large bin gate. The conclusion was determined that in addition to the bottom of silo, larger stress was appeared around the opening in silo wall and the changed cross-section of silo wall and rib stiffener. Therefore the opening in silo wall and the changed cross-section of silo wall and rib stiffener could be the vulnerable points in the silo. According to the vulnerable points listed above, the specific strengthening program is determined.%以实际工程装配式钢板筒仓BC2425为研究对象,分别根据《粮食钢板筒仓设计规范》(GB 50322-2001)和通用有限元软件ANSYSTM对开洞满仓工况下的钢板筒仓进行了应力分析,结果表明:仓体的较大应力不仅出现在仓体底部,还出现在仓壁开口处、仓壁与加劲肋的截面改变处.仓壁开口处和仓壁与加劲肋的截面改变处可能成为筒仓的薄弱部位.针对上述薄弱部位,通过数值分析确定了具体的增强方案.

  17. 浅议某项目中2000m3PTA料仓的设计%Discuss on the Design of 2000m3PTA Silo in A Project

    Institute of Scientific and Technical Information of China (English)

    李静波

    2012-01-01

    结合了一项设计施工完成并已经投产使用的料仓工程,对该料仓的结构特点和设计方法进行探讨。%Combined a silo design construction which had been completed and put into use, to discussing the silo's structural characteristics and the design method.

  18. Intra-arch dimensional measurement validity of laser-scanned digital dental models compared with the original plaster models: a systematic review.

    Science.gov (United States)

    De Luca Canto, G; Pachêco-Pereira, C; Lagravere, M O; Flores-Mir, C; Major, P W

    2015-05-01

    A systematic review was undertaken to evaluate the validity of intra-arch dimensional measurements made from laser-scanned digital dental models in comparison with measurements directly obtained from the original plaster casts (gold standard). Finally included articles were only those reporting studies that compared measurements from digital models produced from laser scanning against their plaster models. Measurements from the original plaster models should have been made using a manual or digital caliper (gold standard). Articles that used scans from impressions or digital photographs were discarded. Detailed individual search strategies for Cochrane, EMBASE, MEDLINE, PubMed, and LILACS were developed. The references cited in the selected articles were also checked for any references that could have been missed in the electronic database searches. A partial gray literature search was undertaken using Google Scholar. The methodology of selected studies was evaluated using the 14-item quality assessment tool for diagnostic accuracy studies (QUADAS). Only 16 studies were finally included for the qualitative/quantitative synthesis. The selected studies consistently agree that the validity of measurements obtained after using a laser scanner from plaster models is similar to direct measurements. Any stated differences would be unlikely clinically relevant. There is consistent scientific evidence to support the validity of measurements from digital dental models in comparison with intra-arch dimensional measurements directly obtained from them. © 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  19. Outcome predictors for treatment success with 5% lidocaine medicated plaster in low back pain with neuropathic components and neuropathic pain after surgical and nonsurgical trauma

    Science.gov (United States)

    Nicolaou, Andrew; Nicholson, Bruce; Hans, Guy; Brasseur, Louis

    2011-01-01

    Five percent lidocaine medicated plaster has been proven efficacious for the symptomatic relief of neuropathic pain in diverse pain conditions which might be attributed to a common localized symptomatology in these indications, possibly with common predictors of treatment success. To discuss potential symptoms and other factors predicting response to treatment with lidocaine plaster for the indications of low back pain with neuropathic components and neuropathic pain after surgical and nonsurgical trauma, 44 pain specialists from 17 countries attended a two-day conference meeting in December 2009. Discussions were based on the retrospective analysis of case reports (sent in by participants in the four weeks prior to the meeting) and the practical experience of the participants. The results indicate some predictors for success with 5% lidocaine medicated plaster for the two indications. Localized pain, hyperalgesia and/or allodynia, and other positive sensory symptoms, such as dysesthesia, were considered positive predictors, whereas widespread pain and negative sensory symptoms were regarded as negative predictors. Paresthesia, diagnosis, and site of pain were considered to be of no predictive value. Common symptomatology with other neurologic pathologies suggests that treatment of localized neuropathic pain symptoms with the plaster can be considered across different neuropathic pain indications. PMID:21386952

  20. Accuracy of Bolton analysis measured in laser scanned digital models compared with plaster models (gold standard) and cone-beam computer tomography images.

    Science.gov (United States)

    Kim, Jooseong; Lagravére, Manuel O

    2016-01-01

    The aim of this study was to compare the accuracy of Bolton analysis obtained from digital models scanned with the Ortho Insight three-dimensional (3D) laser scanner system to those obtained from cone-beam computed tomography (CBCT) images and traditional plaster models. CBCT scans and plaster models were obtained from 50 patients. Plaster models were scanned using the Ortho Insight 3D laser scanner; Bolton ratios were calculated with its software. CBCT scans were imported and analyzed using AVIZO software. Plaster models were measured with a digital caliper. Data were analyzed with descriptive statistics and the intraclass correlation coefficient (ICC). Anterior and overall Bolton ratios obtained by the three different modalities exhibited excellent agreement (> 0.970). The mean differences between the scanned digital models and physical models and between the CBCT images and scanned digital models for overall Bolton ratios were 0.41 ± 0.305% and 0.45 ± 0.456%, respectively; for anterior Bolton ratios, 0.59 ± 0.520% and 1.01 ± 0.780%, respectively. ICC results showed that intraexaminer error reliability was generally excellent (> 0.858 for all three diagnostic modalities), with < 1.45% discrepancy in the Bolton analysis. Laser scanned digital models are highly accurate compared to physical models and CBCT scans for assessing the spatial relationships of dental arches for orthodontic diagnosis.

  1. Influence of tooth dimension on the initial mobility based on plaster casts and X-ray images : A numerical study.

    Science.gov (United States)

    Hartmann, Martin; Dirk, Cornelius; Reimann, Susanne; Keilig, Ludger; Konermann, Anna; Jäger, Andreas; Bourauel, Christoph

    2017-07-01

    The goal was to determine the influence of different geometric parameters of the tooth on the initial tooth mobility and the position of the center of resistance employing numerical models based on scaled X-ray images and plaster casts. The dimensions of tooth 21 were measured in 21 patients, using radiographs and dental casts. Length and mesiodistal width of the tooth were obtained from the X-ray image and the orovestibular diameter from the plaster cast. Finite element models were generated. Cortical and cancellous bone and the periodontal ligament were simulated to create realistic models. Root length (11-17 mm), mesiodistal width (6-10 mm) and orovestibular thickness (7-9 mm) were varied in 1-mm steps to generate 105 models. In the simulation, each model was loaded with a force of 10 N in vestibulopalatinal direction and with a torque of 10 Nmm to determine tooth displacements and center of resistance. Initial tooth displacement and thus mobility increased with decreasing total root surface. The shortest, slimmest and thinnest tooth showed a total deflection of 0.14 mm at the incisal edge, while the longest, widest and thickest tooth showed a total deflection of 0.10 mm. Changes in mesiodistal width had the greatest influence on initial tooth mobility and changes in orovestibular thickness the least. The teeth's center of resistance was positioned between 37 and 43% of the root length measured from the cervical margin of the alveolar bone. The center of resistance of the longest dental root investigated was located around 6% more cervically compared to the one of the shortest dental root. The influence of root width and thickness on the position of the center of resistance was significantly lower than root length. Geometric parameters significantly impact initial tooth mobility and position of the center of resistance. Thus, tooth dimensions should be considered in orthodontic treatment planning. Dental radiographs represent a sufficient validation tool

  2. Building a diagnostic algorithm on localized neuropathic pain (LNP and targeted topical treatment: focus on 5% lidocaine-medicated plaster

    Directory of Open Access Journals (Sweden)

    Casale R

    2014-04-01

    Full Text Available Roberto Casale,1,2 Consalvo Mattia31Department of Clinical Neurophysiology and Pain Rehabilitation Unit, Foundation “Salvatore Maugeri”, Research and Care Institute, IRCCS, Pavia, Italy; 2EFIC Montescano Pain School, Montescano, Italy; 3Department of Medical-Surgical Sciences, Section of Anaesthesia, Intensive Care and Pain Medicine, Faculty of Medicine and Pharmacy, Sapienza University of Rome, ItalyAbstract: Within the broad definition of neuropathic pain, the refinement of clinical diagnostic procedures has led to the introduction of the concept of localized neuropathic pain (LNP. It is characterized by consistent and circumscribed area(s of maximum pain, which are associated with negative or positive sensory signs and/or spontaneous symptoms typical of neuropathic pain. This description outlines the clinical features (currently lacking in guidelines and treatment recommendations in patients for whom topical targeted treatment with 5% lidocaine-medicated plaster is suggested as first-line therapy. Few epidemiologic data are present in the literature but it is generally estimated that about 60% of neuropathic pain conditions are localized, and therefore identifiable as LNP. A mandatory clinical criterion for the diagnosis of LNP is that signs and symptoms must be present in a clearly identified and defined area(s. Cartographic recordings can help to define each area and to assess variations. The diagnosis of LNP relies on careful neurological examination more than on pain questionnaires, but it is recognized that they can be extremely useful for recording the symptom profiles and establishing a more targeted treatment. The most widely studied frequent/relevant clinical presentations of LNP are postherpetic neuralgia, diabetic neuropathy, and neuropathic postoperative pain. They successfully respond to treatment with 5% lidocaine-medicated plaster with equal if not better pain control but with fewer side effects versus conventional systemic

  3. Loss of space and dental arch length after the loss of the lower first primary molar: a longitudinal study.

    Science.gov (United States)

    Cuoghi, O A; Bertoz, F A; de Mendonca, M R; Santos, E C

    1998-01-01

    The premature loss of primary teeth may harm the normal occlusal development, although there are debates relating to the necessity of using space maintainer appliances. The aim of the study is to evaluate the changes in the dental arch perimeter and the space reduction after the premature loss of the lower first primary molar in the mixed dentition stage. The sample consists of 4 lower arch plaster models of 31 patients, within the period of pre-extraction, 6, 12 and 18 months after the lower first primary molar extraction. A reduction of space was of noted with the cuspid dislocation and the permanent incisors moving toward the space of the extraction site. It was concluded that the lower first molar primary premature loss, during the mixed dentition, implicates an immediate placement of a space maintainer.

  4. Effect of Polyester and Plaster of Paris Casts on Determination of Volumetric Bone Mineral Density Assessed by Peripheral Quantitative Computed Tomography (pQCT).

    Science.gov (United States)

    Bullen, Michael; Blanchard, Romane; Rodda, Christine; Pivonka, Peter

    2016-11-01

    Peripheral quantitative computed tomography (pQCT) is a non-invasive, low-radiation tool for measuring volumetric bone mineral density. It has potential for use in fracture healing applications; however, the unknown attenuation effects of cast material on peripheral quantitative computed tomography have contributed to its limited use in this area. The effect of two common cast materials, polyester and Plaster of Paris was investigated by performing both in vitro and in vivo studies. The in vitro study tested the effect of increasing layers of cast material on bone density measurements performed on a hydroxyapatite phantom. Cast thickness was directly associated with a reduction in bone mineral density, with twelve layers of polyester and Plaster of Paris resulting in a 0.55 and 2.21 % decrease in bone density measurements. Precision error in situ with polyester cast material was 0.71 %, and 2.31 % with Plaster of Paris cast material. The in vivo study comprised a prospective trial with 28 healthy adult participants to evaluate the effect of the two cast materials. Trabecular bone mineral density was increased by 0.5 % in the presence of a polyester cast and decreased by 4.22 % in the presence of a Plaster of Paris cast. Cortical bone mineral density was decreased by 3.46 and 5.54 % for polyester and Plaster of Paris, respectively. This study quantified the effects of orthopaedic casts on pQCT-derived bone parameters. The results suggest applicability of commonly utilised cast materials in combination with pQCT to assess fracture healing.

  5. Golden plaster for pain therapy in patients with knee osteoarthritis: study protocol for a multicenter randomized, double-blind, placebo-controlled trial.

    Science.gov (United States)

    Liu, Jin-Tao; Tang, De-Zhi; Li, Xiao-Feng; Zhang, Zhi-Gang; Ji, Wan-Bo; Tao, Shuai; Wang, Yong-Jun; Jiang, Hong

    2013-11-13

    Osteoarthritis is a relatively common musculoskeletal disorder that increases in prevalence with age. Worldwide, knee osteoarthritis is one of the leading causes of disability, particularly in the elderly. In numerous trials of agents for long-term pain therapy, no well-established and replicable results have been achieved. Complementary and alternative medical approaches have been employed for thousands of years to relieve knee osteoarthritis pain. Among herbal medicines, the golden plaster is the preferred and most commonlyused method in China to reduce pain in patients with knee osteoarthritis, as it causes few adverse effects. The purpose of this study will be to evaluate the efficacy and safety of golden plaster on pain in patients with knee osteoarthritis. This study will be a multicenter randomized, double-blind, placebo-controlled trial. A total of 320 participants aged 45 to 79 years with knee osteoarthritis, whose scores on a visual analog scale (VAS) are more than 20 mm,will be randomly allocated into a treatment group and a control group. A golden plaster will be administered externally to participants in the treatment group for 2 weeks, while the control group will receive a placebo plaster externally for 2 weeks. Follow-up will be at regular intervals during a 4-week period with a VAS score for pain, quality of life, and complications. This study will be a methodologically sound randomized controlled trial to assess pain relief after the intervention of golden plaster, compared to a placebo intervention in patients with knee osteoarthritis. ClinicalTrials.gov identifier: ChiCTR-TRC-13003418.

  6. The 5% Lidocaine-Medicated Plaster: Its Inclusion in International Treatment Guidelines for Treating Localized Neuropathic Pain, and Clinical Evidence Supporting its Use.

    Science.gov (United States)

    Baron, Ralf; Allegri, Massimo; Correa-Illanes, Gerardo; Hans, Guy; Serpell, Michael; Mick, Gerard; Mayoral, Victor

    2016-12-01

    When peripheral neuropathic pain affects a specific, clearly demarcated area of the body, it may be described as localized neuropathic pain (LNP). Examples include postherpetic neuralgia and painful diabetic neuropathy, as well as post-surgical and post-traumatic pain. These conditions may respond to topical treatment, i.e., pharmaceutical agents acting locally on the peripheral nervous system, and the topical route offers advantages over systemic administration. Notably, only a small fraction of the dose reaches the systemic circulation, thereby reducing the risk of systemic adverse effects, drug-drug interactions and overdose. From the patient's perspective, the analgesic agent is easily applied to the most painful area(s). The 5% lidocaine-medicated plaster has been used for several years to treat LNP and is registered in approximately 50 countries. Many clinical guidelines recommend this treatment modality as a first-line option for treating LNP, particularly in frail and/or elderly patients and those receiving multiple medications, because the benefit-to-risk ratios are far better than those of systemic analgesics. However, some guidelines make only a weak recommendation for its use. This paper considers the positioning of the 5% lidocaine-medicated plaster in international treatment guidelines and how they may be influenced by the specific criteria used in developing them, such as the methodology employed by randomized, placebo-controlled trials. It then examines the body of evidence supporting use of the plaster in some prevalent LNP conditions. Common themes that emerge from clinical studies are: (1) the excellent tolerability and safety of the plaster, which can increase patients' adherence to treatment, (2) continued efficacy over long-term treatment, and (3) significant reduction in the size of the painful area. On this basis, it is felt that the 5% lidocaine-medicated plaster should be more strongly recommended for treating LNP, either as one component

  7. 微波消毒口腔石膏模型的实验研究%EXPERIMENTAL STUDY ON MICROWAVE DISINFECTION OF CLINICAL PLASTER MODEL

    Institute of Scientific and Technical Information of China (English)

    郝玉梅; 肖瑞森; 张莹; 韩泽民

    2012-01-01

    Objective To evaluate of microwave disinfection effect for clinical plaster model. Methods Bacterial quantitative detection and fluorescence quantitative gene amplification technology were used to evaluate the disinfection efficacy of microwave irradiation for plaster model. Results The output power of microwave oven irradiation was 120W. After exposed for 5 min, Bacillus subtilis spores contaminated on the plaster model can be completely killed, and Hepatitis B virus DNA contamination in dental plaster model can be completely inactivated. Conclusion The common household microwave oven in full power conditions irradiate for 5 min, can effectively kill bacteria and virus polluted on the oral cavity plaster model.%目的 评价微波消毒法对口腔石膏模型的消毒效果.方法 用细菌定量检测和基因扩增荧光定量技术,对微波照射消毒口腔石膏模型的效果进行了观察.结果 用输出功率120 W微波炉对染菌口腔石膏模型进行照射消毒.照射5 min,可完全杀灭污染在口腔石膏模型上的枯草芽孢杆菌,并可完全灭活污染在口腔石膏模型上的乙型肝炎病毒DNA.结论 普通家用微波炉在满功率条件下照射5min,可有效杀灭污染在口腔石膏模型上的细菌和病毒.

  8. 影响大型筒仓配煤精度的因素探讨%Factors affecting coal blending precision in large coal silo

    Institute of Scientific and Technical Information of China (English)

    孙兵; 段衍泉

    2013-01-01

      介绍了沙钢焦化厂大型筒仓的使用情况。导致配煤误差的原因主要是筒仓悬料、计量皮带称故障、称量皮带黏煤。对悬料的原因及采取的处理办法作了详细的介绍。%The application of large coal silo for coking plant of Zhangjiagang Hongfa Group Co .Ltd. has been introduced in this paper where reasons of coal blending error are found ,i.e.coal silo bridg-ing,belt scale failure and coal sticking to the belt and the causes to bridging and relevant solution are also given.

  9. 谈悬空钢梁平台支模筒仓顶板的施工%Discussion on the construction of suspended steel platform formwork silo roof

    Institute of Scientific and Technical Information of China (English)

    郝晓华

    2014-01-01

    结合工程实例,介绍了悬空支模浇筑筒仓顶板的施工工艺,并阐述了钢梁承重体系制作、安装、拆除的操作要点,同时对施工特点进行了总结,从而完善了仓顶支模施工方法,对类似项目施工有一定借鉴意义。%Combining with the engineering example,this paper introduced the construction technology of suspended branches casting silo roof, and elaborated the operation key points of making,installation,demolition of steel bearing system,at the same time summarized the construction characteristics,in order to improve the construction method of silo roof formwork,had certain reference significance to similar project construction.

  10. The application of radiation hard platform in silo sliding mode%辐射硬平台在筒仓滑模中的应用

    Institute of Scientific and Technical Information of China (English)

    张安平

    2015-01-01

    Based on end coal silo engineering of a mining area,this paper discussed the advantages and background of radiation hard platform in silo sliding mode construction,researched mainly the matters needing attention of radiation hard platform in specific construction,pointed out that radiation hard platform in sliding mode construction with cost saving,quality and reliable and other advantages.%以某矿区末煤筒仓工程为依托,论述了辐射硬平台在筒仓滑模施工中的优势以及产生背景,主要对辐射硬平台在具体施工中的注意事项进行了研究,指出辐射硬平台在滑模施工中具有节约成本、质量可靠等优点。

  11. Eco-Homestay: Development Concept On Rural Tourism-Based Conservation Model (Study Case of Sidomulyo Village, Silo District, Jember Regency

    Directory of Open Access Journals (Sweden)

    Alvan Sidiq Asbullah

    2013-09-01

    Full Text Available The purposes of this research were to assess the concept of Eco-Homestay in conservation-based tourism in rural area. A case study was set up at Sidomulyo Village, Silo District, Jember. A qualitative method in the form of in-depth interviews was performed as a tool to generate models. Informants in this study included the staff of the Department of Forestry and Plantation, lecturer of the Faculty of Agriculture and Polytechnic of Jember, State University of Jember, and Sidomulyo community in Silo Districts, Jember. The result showed that the purposes of eco-homestay can be reached by managing the structure of integrated development, structure of organizational management, structure of financial management, marketing strategies, operational strategies and physical building. Keywords: conservation, eco-homestay, rural tourism, Sidomulyo

  12. 聚丙烯料仓脱气压降算法研究%Research of Calculation Method for Pressure Drop in Purging of Polypropylene Silo

    Institute of Scientific and Technical Information of China (English)

    汪洋; 邢桂坤

    2015-01-01

    料仓脱气可以有效减少聚丙烯料仓闪爆事故的发生。介绍了聚丙烯粒料料仓脱气的工艺流程,着重论述了在颗粒床层的实际环境中料仓脱气压降的计算方法,并通过实际工程案例对该方法进行验证。%Purging in silo can efficiently avoid the occurrence possibility of explosion in polypropylene silo. In this paper, the flow process of purging in polypropylene silo was introduced. The calculation of pressure drop in purging process under the condition of pellet bed was emphatically described, and with practical example this method was verified.

  13. 欧洲筒仓荷载规范解析%Commentary on Eurocode 1 — Actions on structures—Part 4: Silos and tanks

    Institute of Scientific and Technical Information of China (English)

    段君峰; 李坤由

    2013-01-01

    本文通过对欧洲筒仓荷载规范Eurocode 1-Actions on structures-Part 4:Silos and tank(EN 1991-4:2006)体系的介绍,并以细长筒仓为例进行了内力计算,希望对业内同仁得以借鉴和参考.

  14. Kinetics of oil saponification by lead salts in ancient preparations of pharmaceutical lead plasters and painting lead mediums.

    Science.gov (United States)

    Cotte, M; Checroun, E; Susini, J; Dumas, P; Tchoreloff, P; Besnard, M; Walter, Ph

    2006-12-15

    Lead soaps can be found in archaeological cosmetics as well as in oil paintings, as product of interactions of lead salts with oil. In this context, a better understanding of the formation of lead soaps allows a follow-up of the historical evolution of preparation recipes and provides new insights into conservation conditions. First, ancient recipes of both pharmaceutical lead plasters and painting lead mediums, mixtures of oil and lead salts, were reconstructed. The ester saponification by lead salts is determined by the preparation parameters which were quantified by FT-IR spectrometry. In particular, ATR/FT-IR spectrometer was calibrated by the standard addition method to quantitatively follow the kinetics of this reaction. The influence of different parameters such as temperature, presence of water and choice of lead salts was assessed: the saponification is clearly accelerated by water and heating. This analysis provides chemical explanations to the historical evolution of cosmetic and painting preparation recipes.

  15. A quantitative analysis of IRT data for the evaluation of plaster degradation at the Dome of Magdeburg (Germany)

    Science.gov (United States)

    Di Maio, Rosa; Maierhofer, Christiane; Mancini, Cecilia; Piegari, Ester

    2013-04-01

    Infrared Thermography (IRT) is a helpful method for the nondestructive evaluation of artworks and buildings of historical interest since it is able to provide indications about most of degradation sources, such as alteration of material consistency, formation of microcracks, debondings, etc. The most used procedures for physical and geometrical characterization of the thermal anomaly sources are based on numerical models that solve the forward thermal problem, i.e. they find the solution of the Fourier differential equation, which describes the heat transfer in a medium. In this framework, we present a Finite Difference method to evaluate the conservation state of the Dome of Magdeburg (Germany). In particular, the study is focused on the analysis of the thermal images acquired on the east wing of the cloister from the 13th century, and is aimed to characterize its plaster score. The structure was heated with an infrared radiator and thermal images were acquired on both heating and cooling phase for fifteen minutes. The proposed conservative FD method allows taking into account for varying thermal conductivity, density and specific heat of defects and disrupted materials. The heat transfer problem is formulated in one and two dimensions and, therefore, it is able to characterize multi-layered structures. The investigated structure is made of three plaster layers (one lime wash layer that overlaps two lime mortar layers) and a sandstone background. Numerical simulations have shown a very good match between the experimental and theoretical curves for all the considered anomalous areas, for both 1D and 2D formulations, providing an average percentage error of the order of 10-1%. In particular, the study allowed to define thickness, depth and nature (density, thermal conductivity and specific heat) of the thermal anomaly sources, attributable to the degradation of the lime mortar layer at different depths. The application of the codes provided helpful indications for

  16. Classification of multi-layered plaster in St. Abbondio Cloister at Como, Italy: an analytical tool for architectural archaeology

    Directory of Open Access Journals (Sweden)

    Sansonetti, A.

    2006-06-01

    Full Text Available St. Abbondio, at Como, Italy, is one of the most outstandingRomanesque basilicas in Northern Italy. Theentire building, and particularly the cloister, has beenthe object of a number of restorations over the centuries,as well as a significant conservation endeavourconducted between 2000 and 2003. In the in-depthdiagnostic survey undertaken on that occasion, thecomposition and morphology of the plaster in bothinteriors and exteriors were determined to obtain furtherinsight into the history of the cloister and its conservation.Plaster representative of the various phasesof construction were characterized with techniquessuch as powder X-ray diffraction, mercury intrusionporosimetry, thin section optical microscopy and atomicspectrometry. As a result of these analyses, groupsof samples with similar characteristics could be identified,confirming historiographic hypotheses on thesequence of the restoration and conservation workdone on the building and establishing a possible toolfor architectural archaeology.S. Abbondio (Como, Italia es una de las mas extraordinariasbasilicas romanicas presentes en el norte de Italia.El edificio entero y en particular el claustro ha sido expuestoa varias intervenciones durante los ultimos siglos, enparticular los ultimos trabajos de conservacion ejecutadosentre los anos 2000 y 2003. En esta ocasion se ha efectuadouna vasta campana diagnostica sobre los revoquestanto internos como externos, destinada a clasificarlosdesde el punto de vista compositivo-morfologico y paradescubrir la historia sobre la conservacion del claustro.Revoques representativos de las diferentes fases constructivashan sido identificados con la utilizacion de metodoscomo el analisis de difraccion de rayos X en polvo,porosimetria por intrusion de mercurio, microscopia opticapara secciones finas y espectrometria atomica. Losresultados han permitido agrupar las muestras que presentabancaracteristicas similares, confirmando hipotesishistoricas sobre la

  17. A comparison of the accuracy of polyether, polyvinyl siloxane, and plaster impressions for long-span implant-supported prostheses.

    Science.gov (United States)

    Hoods-Moonsammy, Vyonne J; Owen, Peter; Howes, Dale G

    2014-01-01

    The purpose of this study was to compare the capacity of different impression materials to accurately reproduce the positions of five implant analogs on a master model by comparing the resulting cast with the stainless steel master model. The study was motivated by the knowledge that distortions can occur during impression making and the pouring of casts and that this distortion may produce inaccuracies of subsequent restorations, especially long-span castings for implant superstructures. The master model was a stainless steel model with five implant analogs. The impression materials used were impression plaster (Plastogum, Harry J Bosworth), a polyether (Impregum Penta, 3M ESPE), and two polyvinyl siloxane (PVS) materials (Aquasil Monophase and Aquasil putty with light-body wash, Dentsply). Five impressions were made with each impression material and cast in die stone under strictly controlled laboratory conditions. The positions of the implants on the master model, the impression copings, and the implant analogs in the subsequent casts were measured using a coordinate measuring machine that measures within 4 μm of accuracy. Statistical analyses indicated that distortion occurred in all of the impression materials, but inconsistently. The PVS monophase material reproduced the master model most accurately. Although there was no significant distortion between the impressions and the master model or between the impressions and their casts, there were distortions between the master model and the master casts, which highlighted the cumulative effects of the distortions. The polyether material proved to be the most reliable in terms of predictability. The impression plaster displayed cumulative distortion, and the PVS putty with light body showed the least reliability. Some of the distortions observed are of clinical significance and likely to contribute to a lack of passive fit of any superstructure. The inaccuracy of these analog materials and procedures suggested

  18. 小儿健脾贴膏质量标准研究%Quality Standard of Xiaoerjianpi Plaster

    Institute of Scientific and Technical Information of China (English)

    颜晓航; 薛玉梅

    2011-01-01

    目的 完善小儿健脾贴膏的质量标准.方法 对处方中丁香、吴茱萸、五倍子、冰片分别采用薄层色谱法和高效液相色谱法进行鉴别和含量测定研究.结果 建立了吴茱萸、五倍子、冰片3项薄层鉴别以及丁香中丁香酚的液相色谱鉴别和含量测定.薄层图谱斑点清晰,空白无干扰;丁香酚加样回收率为82.2%,RSD为2.9%(n=6).结论 薄层色谱法鉴别、高效液相色谱法含量测定专属性强,方法简便、重现性好,可较全面地控制小儿健脾贴膏的质量.%Objective To establish the quality specification of Xiaoerjianpi Plaster. Methods Flos Caryophylli, Fructus Evodiae, Galla Chinensis and Borneolum syntheticum were identified by TLC or HPLC. Eugenol in Borneolum syntheticum was determined by HPLC. Results The developed TLC spots were fairly clear, and the blank test showed no interference. The average recovery of eugenol was 82.2% , RSD was 2.9% (n = 6). Conclusion The methods are simple and special with good reproducibility, and the method can be used for quality control of Xiaoerjianpi Plaster.

  19. 三王止痛膏治疗癌性疼痛60例疗效观察%Observation on therapeutic effect of Sanwang pain alleviating plaster on cancerous pain in 60 cases

    Institute of Scientific and Technical Information of China (English)

    潘敏求; 黎月恒; 蒋益兰; 吴玉华; 苏旭春

    2002-01-01

    Objective To observe the therapeutic effect of Sanwang pain alleviating plaster on cancerous pain.Method The study was a randomized,single blinded trial.The patients were randomly divided into 2 groups,study group and control group.Control group received toad plaster.Pain level,functions time and duration of sanwang pain alleviating plaster,quality of life,peripheral blood picture,liver and kidney function,EEG,local stimulation and allergy of skin were evaluated before and after treatment.Result For the study group,total effective rate,duration,KS improvement rate were significantly raised as compared with control group.Total effective rate was different between two groups(P< 0.05) .Conclusion Sanwang pain alleviating plaster can effectively control cancerous pain and improve quality of life.

  20. Hair Loss

    Science.gov (United States)

    ... loss at the scarred areas. These conditions include lichen planus, some types of lupus and sarcoidosis. Hair- ... increase your risk of hair loss, including: Family history Age Poor nutrition Certain medical conditions, such as ...

  1. Hearing Loss

    Science.gov (United States)

    ... effects on your hearing — ringing in the ear (tinnitus) or hearing loss — can occur if you take ... adults with hearing loss, commonly reported problems include: Depression Anxiety An often false sense that others are ...

  2. CHEMICAL COMPOSITION AND ENERGY ESTIMATION FROM ENSILED CASSAVA MASS WITH WHEAT MEAL IN EXPERIMENTAL SILOS CARACTERIZAÇÃO BROMATOLÓGICA E ESTIMATIVAS DE ENERGIA DA MASSA DE MANDIOCA ENSILADA COM FARELO DE TRIGO EM SILOS LABORATORIAIS

    Directory of Open Access Journals (Sweden)

    Elieldo Lameira Brito

    2007-09-01

    Full Text Available

    The experiment was conducted in order to evaluate the pH, chemical composition, fractions which constitute the total carbohydrates (CHT and energy values of cassava mass silage with wheat meal in PVC silos with capacity for 12 kg, randomly distributed in three replications. The samples had been taken at 0, 6, 18, 25, 45 and 60 days after ensilage. The dry matter (DM, ether extract (EE, crude protein (CP, neutral detergent fiber (NDF, acid detergent fiber (ADF, non-fiber carbohydrates (NFC, lignin contents and pH, CHT fraction and energy were analyzed. There was linear effect (P<0.05 for pH values, that decreased with the ensilage time, and positive quadratic effect (P<0.05 for DM concentration. The CP, EE, NDF, ADF, lignin, CHT texts of PB, EE, FDN, FDA, lignin, CHT, CNF, total fractions of CHT, total digestible nutrients and energy contents were  constant (P>0.05 in function of the ensilage time. In func-tion of the results, the cassava silage is showed as alternative source of energy concentrate for ruminants feeding.

    KEY-WORDS: Animal nutrition, byproducts, conservation, energy.

    Objetivou-se avaliar os valores de pH e a composi-ção bromatológica, quantificar as frações que constituem os carboidratos totais (CHT e estimar os valores energéticos da silagem da massa de mandioca enriquecida com 4% de farelo de trigo, em silos laboratoriais de PVC com capaci-dade para 12 kg, distribuídos ao acaso com três repetições por tratamento. As amostras foram tomadas aos 0, 6, 18, 25, 45 e 60 dias após a ensilagem. Analisaram-se os teores de matéria seca (MS, de extrato etéreo (EE, de proteína bruta (PB, de fibra em detergente neutro (FDN, de fibra em detergente ácido (FDA, de lignina, de valores de pH e estimativas da fração de CHT e de energia. Houve efeito linear (P<0,05 para os valores de pH, que decresceram com o tempo de ensilagem, e feito quadrático positivo (P<0,05 para os teores de MS. Os teores de PB, de EE, de

  3. Three-dimensional finite element simulation of static granular material pressure for steel silos%钢筒仓散料静态压力的三维有限元模拟

    Institute of Scientific and Technical Information of China (English)

    杨鸿; 杨代恒; 赵阳

    2011-01-01

    为考察所储存散料对钢简仓仓壁的静态压力,建立考虑散料与仓壁相互作用的钢筒仓静态散料压力三维有限元分析模型.散料假定为各向同性,塑性阶段采用Drucker-Prager塑性模型,散料与仓壁之间的接触效应采用刚柔接触模型和面面接触方法进行模拟.利用所建立的有限元模型对平底钢筒仓(浅仓和深仓)及锥底钢筒仓的散料压力进行数值模拟,并将数值结果与欧洲钢筒仓规范、我国粮食钢板简仓设计规范进行对比分析.文中还对平底钢筒仓散料的泊松比、内摩擦角、膨胀角和摩擦系数进行参数分析,结果表明泊松比和内摩擦角的影响较大.%In order to simulate the static pressures from stored granular materials, a three-dimensional finite element model accounting for the interaction between the granular material and the silo wall was established. The stored granular material was considered to follow a law of behavior of isotropic elastic material with the Drucker-Prager plasticity criterion in the plastic range, and the interaction between the stored material and the silo wall was simulated by the rigid-flexible contact model and the face-to-face contact method. Granular material pressures for both flat-bottomed steel silos (shallow silos and deep silos) and conical-bottomed steel silos were simulated employing the proposed FE model, and the results were compared with those of the Eurocode for steel silos and the Chinese design code for grain steel silos. A parametric analysis on flat-bottomed steel silos was also carried out to study the effects of granular material's Poisson's ratio, internal friction angle, dilatancy angle and friction coefficient, and it is found that the effects of the Poisson's ratio and internal friction angle are obvious.

  4. In situ characterization of ancient plaster and pigments on tomb walls in Egypt using energy dispersive X-ray diffraction and fluorescence

    Energy Technology Data Exchange (ETDEWEB)

    Uda, M. E-mail: muda@waseda.jp

    2004-11-01

    A portable type of energy dispersive X-ray diffraction and fluorescence (ED-XRDF) spectrometer was developed, whose operation mode is completely different from that of an X-ray diffractometer commercially available. The former is operated in energy dispersive mode but the latter in angle dispersive mode. The performance of the ED-XRDF spectrometer was tested in the field, i.e. in the tomb of Amenhotep III, built in 1364 B.C. or earlier in Egypt. The crystal structure and chemical composition of ancient plaster and pigments were successfully determined in the field using the spectrometer. The same areas investigated by the ED-XRDF spectrometer were also examined with an optical microscope. The plaster is found to be composed of anhydrite, calcite and quartz. White and yellow pigments were identified as huntite and orpiment, respectively. Egyptian blue and goethite were found in the green colored parts.

  5. Reinforced plaster by means of the synergic action between concrete additives (superfluidifiers, fluidiflers and airing-plasticizers and E glass fibres

    Directory of Open Access Journals (Sweden)

    del Río Merino, M.

    2000-12-01

    Full Text Available Through the analysis of the different compounds (plaster + additives + E glass fibres we pretend to demostrate that a synergic action is present between certain concrete additives (superfluidifiers, fluidiflers, and airingplasticizers and E glass fibre, on the basis of the flection resistance of plaster matrix based compound materials.

    Mediante el análisis de diferentes compuestos (escayola + aditivos + fibras de vidrio E se pretende demostrar que existe una acción sinérgica entre ciertos aditivos del hormigón (superfluidificantes, fluidificantes y aireantes-plastificantes y los refuerzos a base de fibras de vidrio E, sobre la resistencia a flexión de los materiales compuestos de matriz principal escayola.

  6. Calculation for structure of steel storage and distribution silo with multi-discharge outlets%钢结构多出料口给配料仓结构计算

    Institute of Scientific and Technical Information of China (English)

    吴位民; 马魁文; 李勇

    2012-01-01

    During the structural design of steel storage and distribution silo with multi-discharge outlets, the load computational formula for silo materials is researched according to granular mechanics, the characteristics of such silo are analyzed, the design theory for multi-discharge outlet steel silo is put forward, and computational analysis for its structure is performed by the finite element software, which provides significant guidance to structural design of large steel silo.%在对钢结构多出料口给配料仓结构设计过程中,根据散体力学理论研究了料仓物料的载荷计算公式,分析了多出料口给配料仓的特点,提出了针对多出料口钢仓的设计理念,并利用有限元软件对结构进行了计算分析.对大型钢料仓结构设计具有重要的指导意义.

  7. 钢筋混凝土筒仓仓壁强度有限元分析%STRENGTH ANALYSIS OF REINFORCED CONCRETE SILO WALL BASED ON FINITE ELEMENT METHOD

    Institute of Scientific and Technical Information of China (English)

    付明堂; 梁醒培; 李恒

    2011-01-01

    采用有限元法对钢筋混凝土筒仓仓壁受力进行了静力有限元计算,得到了仓壁的详细应力分布情况,以及钢筋和混凝土共同受力时各自承担的环向拉力.基于计算结果对仓壁受力进行了分析,结果表明:我国的《混凝土筒仓设计规范》能够满足仓壁的静力强度要求.%The static stress of reinforced concrete silo wall was calculated using finite element method. The detailed stress distribution of the silo wall and the circumferential tensile forces respectively applied on the steel bar and concrete were obtained when the steel bar and concrete bore force together. Based on the calculation results, the article analyzed the force condition of the silo wall, and the results showed that the Code for design of reinforced concrete silos could meet the requirement for the static strength of the silo wall.

  8. Discussion on Dust Explosion Protection Partition of Coal Silo Area in Huanghua Port Phase-3 Project%关于黄骅港三期工程储煤筒仓防爆分区划分的探讨

    Institute of Scientific and Technical Information of China (English)

    刘璠; 魏美芳

    2016-01-01

    Huanghua Port phase-3 project is the first domestic project that stores a mass of coal by using silos. So far there is no available standard for the dust explosion protection partition of coal silos. An introduction has been given to the program of using silos to store coal. By comparing the natures of coal and grain, it is found that those two substances are similar. Therefore coal silo area can be partitioned according to dust-explosion-protection partition standard of grain silos.%黄骅港三期工程是国内首个在港口大规模使用筒仓储煤的工程,储煤筒仓的防爆分区划分无现成规范可循。文中介绍了筒仓储煤方案,通过对比煤炭与粮食的性质,认为该两种物质存在一定相似性。提出储煤筒仓的防爆分区可参照有明确规范规定的粮食筒仓进行划分。

  9. Finite element analysis of silo considering the interaction of wall-basis-foundation%考虑仓壁-基础-地基相互作用时筒仓结构的有限元分析

    Institute of Scientific and Technical Information of China (English)

    马瑞挺; 孟云芳

    2012-01-01

    In order to calculate interaction force from wall-basis-foundation of silo,it is analyzed with ANSYS software under different conditions,rigid foundation or elastic foundation,shallow or deep silo,and axial symmetry load.The results of analysis show that the internal force of silo placed on elastic foundation is more rational than that of silo placed on rigid foundation.Notable problems are listed with silo design examples according to No Moment theory of design in"Code for design of reinforced concrete silos".%为了计算仓壁-基础-地基的相互作用,利用有限元软件ANSYS对分别放置于弹性地基和刚性地基上受轴对称荷载的浅仓和深仓进行地基-基础-结构共同作用的分析.分析结果表明,将筒仓放置于弹性地基上比放置于刚性地基上,其结构内部受力更为合理,并结合具体算例提出了在筒仓结构计算中按《钢筋混凝土筒仓设计规范》提供的无矩理论计算时应注意的问题.

  10. Effects of topical diclofenac plus heparin (DHEP+H plaster) on somatic pain sensitivity in healthy subjects with a latent algogenic condition of the lower limb.

    Science.gov (United States)

    Affaitati, Giannapia; Fabrizio, Alessandra; Frangione, Valeria; Lanzarotti, Arturo; Lopopolo, Mariangela; Tafuri, Emmanuele; Lapenna, Domenico; Giamberardino, Maria Adele; Costantini, Raffaele

    2015-01-01

    To evaluate whether a diclofenac epolamine + heparin topical (plaster) is more effective than diclofenac plaster alone in reducing deep somatic hyperalgesia in subjects without spontaneous pain and whether the effect is linked to or independent of the anti-edematous action of heparin. Prospective, double-blind, randomized and controlled, four-arm parallel design trial. One hundred and four patients (84 women, 20 men, mean age 42.2 ± 13.3 years), with deep somatic hyperalgesia in one thigh, randomly assigned to one of 4 groups of 26 each. Each group underwent one of the following plaster treatments on one thigh: diclofenac+heparin; diclofenac; heparin; placebo, for 7 days, renewing the plaster every 24 hours. Before treatment (day 1), at day 4 and day 8, assessment of (a) pressure and electrical pain thresholds of vastus lateralis and overlying subcutis and skin; and (b) structure/thickness of subcutis and muscle with ultrasounds at the same level. During treatment, in placebo and heparin, no significant threshold changes, except subcutis thresholds which increased slightly (P < 0.02); in diclofenac and diclofenac+heparin, significant increase in all thresholds (0.0001 < P < 0.04). Electrical muscle pain thresholds increased significantly more in diclofenac+heparin than in diclofenac, heparin, and placebo (0.0001 < P < 0.04). In all groups: no edema and thickness changes at ultrasounds in muscle and subcutis. Topical diclofenac+heparin is significantly more effective than diclofenac alone in reducing muscle hyperalgesia in subjects without spontaneous pain, independently of the anti-edematous action of heparin. The results provide a rationale for the use of diclofenac+heparin also in algogenic conditions without evident signs of injury/edema/hematoma. © 2014 World Institute of Pain.

  11. Phosphor plasters of CaSO{sub 4}:Dy on the courtyard wall of Djehuty's tomb (Luxor, Egypt)

    Energy Technology Data Exchange (ETDEWEB)

    Garcia-Guinea, J. [Museo Nacional de Ciencias Naturales, CSIC. C/ Jose Gutierrez Abascal 2, 28006 Madrid (Spain)], E-mail: guinea@mncn.csic.es; Sanchez-Moral, S. [Museo Nacional de Ciencias Naturales, CSIC. C/ Jose Gutierrez Abascal 2, 28006 Madrid (Spain); Correcher, V.; Sanchez-Munoz, S. [CIEMAT. Av. Complutense 22, 28040 Madrid (Spain); Cuezva, S. [Museo Nacional de Ciencias Naturales, CSIC. C/ Jose Gutierrez Abascal 2, 28006 Madrid (Spain); Cremades, A. [Dpt. Fisica de Materiales, Facultad de Fisicas, Universidad Complutense, 28040 Madrid (Spain); Benavente, D. [Dpto. CC. de la Tierra y del Medio Ambiente. Univ. Alicante, 03080 Alicante (Spain); Galan, J.M. [Instituto de Filologia, CSIC. C/Duque de Medinaceli 6, 28014 Madrid (Spain)

    2008-02-15

    The X-ray diffraction (XRD) and environmental scanning electron microscopy (ESEM) analyses of plasters collected from the courtyard walls of Djehuty's tomb show anhydrite, calcite, dolomite, quartz, alkali feldspars and accessorial amounts of halite and illite. The external outer bed is mainly composed by anhydrite, since the original hydrous phases of gypsum plaster were desiccated during thirty centuries in the dry land environment of the Luxor area, under low relative humidity and high temperatures. The luminescence analyses by thermoluminescence (TL) and cathodoluminescence (CL) demonstrate as one plaster sample (m8), i.e., 95% anhydrite, displays a gigantic TL emission of 33 555 a.u. and a SEM/CL emission of 2319 a.u. maxima peak. The spectra CL also exhibits a 484 nm peak attributable to the classic {sup 4}F{sub 9/2}{yields}{sup 6}H{sub 15/2} transition circa 490 nm of Dy{sup 3+} and a 573 nm emission of Dy{sup 3+} masked in a broad emission band centered at 620 nm. The common presence of sodium minerals such as halite or albite together with the probable presence of sodium in waters points to Na{sup +} ions acting as compensators of Dy{sup 3+} to maintain the electrical neutrality of the CaSO{sub 4}:Dy phosphor lattice. Further analyses of more plaster CaSO{sub 4} micro-samples could demonstrate if this observation is just an isolated mineralogical chance or an intentional archaeological handling.

  12. Lead, cadmium, and zinc concentrations in plaster and mortar from structures in Jasper and Newton Counties, Missouri (Tri-State Mining District).

    Science.gov (United States)

    Perry, Phyllis M; Pavlik, Jeffrey W; Sheets, Ralph W; Biagioni, Richard N

    2005-01-05

    The primary goal of this study was to evaluate anecdotal evidence that within Jasper and Newton Counties, Missouri, two counties within the Tri-State Mining District, granular mine tailings were commonly used in place of river sands in wall plasters and mortar. Interior wall plaster and mortar samples from structures in this mining district were analyzed for lead, cadmium, and zinc, and compared to samples from Springfield, MO (comparison site). The Jasper and Newton County samples showed elevated concentrations of the three elements, consistent with the inclusion of mine tailings, with a number of samples containing lead and cadmium at concentrations greater than EPA remediation targets for yard soil. X-ray diffraction studies showed the presence of the zinc ore minerals, sphalerite and hemimorphite, in high level samples. Thin section optical studies identified the major component of the aggregate as chert, a mineral abundant within the tailing piles. Because dust from crumbling plaster and mortar could represent an avenue for significant heavy metal exposure to building occupants, we suggest that there may be associated health consequences that should be further evaluated.

  13. [Combination effects of capsicum plaster at the Korean hand acupuncture points k-d2 with prophylactic antiemetic on postoperative nausea and vomiting after gynecologic laparoscopy].

    Science.gov (United States)

    Jung, Hyun Jung; Park, Sang Youn

    2013-04-01

    This study was done to evaluate the combination effects of capsicum plaster at the Korean hand acupuncture points K-D2 with prophylactic antiemetic on Postoperative Nausea and Vomiting (PONV). An experimental research design (a randomized, a double-blinded, and a placebo-control procedure) was used. The participants were female patients undergoing gynecologic laparoscopy; the control group (n=34) received intravenous prophylactic ramosetron 0.3mg, while the experimental group (n=34) had Korean Hand Therapy additionally. In the experimental group, capsicum plaster was applied at K-D2 of both 2nd and 4th fingers by means of Korean Hand Therapy for a period of 30 minutes before the induction of anesthesia and removed 8 hours after the laparoscopy. The occurrence of nausea, nausea intensity and need for rescue with antiemetic in the experimental group was significantly less than in the control group 2 hours after surgery. Results of the study show capsicum plaster at K-D2 is an effective method for reducing PONV in spite of the low occurrence of PONV because of the prophylactic antiemetic medication.

  14. Lead, cadmium, and zinc concentrations in plaster and mortar from structures in Jasper and Newton Counties, Missouri (Tri-State Mining District)

    Energy Technology Data Exchange (ETDEWEB)

    Perry, Phyllis M. [Chemistry Department, Southwest Missouri State University, 901 S. National Avenue, Springfield, MO 65804 (United States); Pavlik, Jeffrey W. [Chemistry Department, Southwest Missouri State University, 901 S. National Avenue, Springfield, MO 65804 (United States); Sheets, Ralph W. [Chemistry Department, Southwest Missouri State University, 901 S. National Avenue, Springfield, MO 65804 (United States); Biagioni, Richard N. [Chemistry Department, Southwest Missouri State University, 901 S. National Avenue, Springfield, MO 65804 (United States)]. E-mail: rnb266f@smsu.edu

    2005-01-05

    The primary goal of this study was to evaluate anecdotal evidence that within Jasper and Newton Counties, Missouri, two counties within the Tri-State Mining District, granular mine tailings were commonly used in place of river sands in wall plasters and mortar. Interior wall plaster and mortar samples from structures in this mining district were analyzed for lead, cadmium, and zinc, and compared to samples from Springfield, MO (comparison site). The Jasper and Newton County samples showed elevated concentrations of the three elements, consistent with the inclusion of mine tailings, with a number of samples containing lead and cadmium at concentrations greater than EPA remediation targets for yard soil. X-ray diffraction studies showed the presence of the zinc ore minerals, sphalerite and hemimorphite, in high level samples. Thin section optical studies identified the major component of the aggregate as chert, a mineral abundant within the tailing piles. Because dust from crumbling plaster and mortar could represent an avenue for significant heavy metal exposure to building occupants, we suggest that there may be associated health consequences that should be further evaluated.

  15. Clinical Observation on Sheng's Black Plaster in the Treatment of Tendon Injury%生氏黑膏药治疗筋伤的临床观察

    Institute of Scientific and Technical Information of China (English)

    生家耀

    2012-01-01

    目的:探讨生氏黑膏药治疗筋伤的临床疗效.方法:196例筋伤患者采用生氏黑膏药(由麝香、牛黄、珍珠、三七、鹿茸、冰片、血竭、鳖甲等90味原料制成)治疗.结果:痊愈162例,好转30例,无效4例,有效率97.95%.结论:生氏黑膏药治疗筋伤的疗效显著.%Objective:To observe clinical effects of Sheng's Black Plaster on the treatment of tendon injury. Methods: 196 patients of tendon injury were treated by the Sheng's Black Plaster( composed of 90 herbs such as Musk, Bezoar,Genuine pearl, Panax notoginseng, Cornua cervi pantotrichum, Malayan camphor, Daemonorops draco, Carapax trionycis and so on). Results: After treatment, 162 cases were healed,30 were improved,4 were ineffective and the effective rate was 97. 95% . Conclusion:The Sheng's Black Plaster has significant curative effects on the treatment of tendon injury.

  16. Use of 5% lidocaine medicated plaster to treat localized neuropathic pain secondary to traumatic injury of peripheral nerves

    Directory of Open Access Journals (Sweden)

    Correa-Illanes G

    2012-07-01

    Full Text Available Gerardo Correa-Illanes,1 Ricardo Roa,2 José Luis Piñeros,2 Wilfredo Calderón31Rehabilitation Department, 2Burns and Plastic Surgery Department, Hospital del Trabajador, 3Plastic Surgery Department, Hospital del Salvador, Santiago, ChileObjective: The efficacy of 5% lidocaine medicated plaster (LMP has previously been demonstrated in post-traumatic localized neuropathic pain. This study evaluated the use of LMP in localized neuropathic pain secondary to traumatic peripheral nerve injury.Patients and methods: This prospective observational study enrolled patients with traumatic injuries to peripheral nerves that were accompanied by localized neuropathic pain of more than 3 months duration. Demographic variables, pain intensity (measured using the numeric rating scale; NRS, answers to the Douleur Neuropathique 4 (DN4 questionnaire, and the size of the painful area were recorded.Results: Nineteen patients were included, aged (mean ± standard deviation 41.4 ± 15.7 years. Nerve injuries affected the upper (eight patients or lower (11 patients limbs. The mean duration of pain before starting treatment with LMP was 22.6 ± 43.5 months (median 8 months. Mean baseline values included: NRS 6.7 ± 1.6, painful area 17.8 ± 10.4 cm2 (median 18 cm2, and DN4 score 6.7 ± 1.4. The mean duration of treatment with LMP was 19.5 ± 10.0 weeks (median 17.4 weeks. Mean values after treatment were: NRS 2.8 ± 1.5 (≥3 point reduction in 79% of patients, ≥50% reduction in 57.9% of patients and painful area 2.1 ± 2.3 cm2 (median 1 cm2, ≥50% reduction in 94.7% of patients. Functional improvement after treatment was observed in 14/19 patients (73.7%.Conclusion: LMP effectively treated traumatic injuries of peripheral nerves which presented with chronic localized neuropathic pain, reducing both pain intensity and the size of the painful area.Keywords: chronic post-surgical pain, chronic post-traumatic pain, 5% lidocaine medicated plaster, neuropathic pain

  17. Temperature and air velocity effects on ethanol emission from corn silage with the characteristics of an exposed silo face

    Science.gov (United States)

    Montes, Felipe; Hafner, Sasha D.; Rotz, C. Alan; Mitloehner, Frank M.

    2010-05-01

    Volatile organic compounds (VOCs) from agricultural sources are believed to be an important contributor to tropospheric ozone in some locations. Recent research suggests that silage is a major source of VOCs emitted from agriculture, but only limited data exist on silage emissions. Ethanol is the most abundant VOC emitted from corn silage; therefore, ethanol was used as a representative compound to characterize the pattern of emission over time and to quantify the effect of air velocity and temperature on emission rate. Ethanol emission was measured from corn silage samples removed intact from a bunker silo. Emission rate was monitored over 12 h for a range in air velocity (0.05, 0.5, and 5 m s -1) and temperature (5, 20, and 35 °C) using a wind tunnel system. Ethanol flux ranged from 0.47 to 210 g m -2 h -1 and 12 h cumulative emission ranged from 8.5 to 260 g m -2. Ethanol flux was highly dependent on exposure time, declining rapidly over the first hour and then continuing to decline more slowly over the duration of the 12 h trials. The 12 h cumulative emission increased by a factor of three with a 30 °C increase in temperature and by a factor of nine with a 100-fold increase in air velocity. Effects of air velocity, temperature, and air-filled porosity were generally consistent with a conceptual model of VOC emission from silage. Exposure duration, temperature, and air velocity should be taken into consideration when measuring emission rates of VOCs from silage, so emission rate data obtained from studies that utilize low air flow methods are not likely representative of field conditions.

  18. 经溜槽装入筒仓的玉米减损效果试验%The Effect of Detract of Corn into the Silo from Chute

    Institute of Scientific and Technical Information of China (English)

    唐福元; 冯家畅; 严晓婕; 杨文生; 程绪铎; 温吉华; 杨大明; 单贺年

    2015-01-01

    Corn of different moisture content (11.64%,13.54%,15.43%,16.43 %w.b.)went into a silo starting from the top of the silo.One condition was that corn flow through the straight chute and the spiral chute into the silo,impacting against bottom of the silo.Other condition was that corn start from the top of the silo,free falling and impacting against bottom of the silo.The broken ratios of impact of corn were measured.The corns of without im-pact and yet impact were compressed by Texture analyzer to determine the destructive force and destructive energy of the corn.The experimental results showed that after the collision broken ratio of corn increase as moisture content of corn decrease,broken ratio of corn flowing through the chute was 3.84% but that of corn free falling was 7.65%, broken ratio of corn flowing through the chute significantly less than that of corn free falling;the average value of de-structive force of corn flowing through the chute was 234.96 N,and the average value of destructive energy of corn was 49.71 mJ;the average value of destructive force of corn free falling was 219.09 N,and the average value of de-structive energy of corn was 42.43 mJ.The destructive force and destructive energy of corn flowing through the chute significantly was bigger than that of corn free falling.The experimental results showed that the chute to buffer the col-lision effect.The effect of detract of the chute was obvious.%不同含水率(11.64%、13.54%、15.43%、16.43%w.b.)的玉米从仓顶入仓,一种工况是玉米经直溜槽与螺旋溜槽流入筒仓与仓底碰撞;另一种工况是玉米从仓顶自由下落与仓底碰撞。测定2种工况下落碰撞的玉米籽粒破碎率,并使用质构仪测定2种碰撞后的玉米籽粒及未碰撞的玉米籽粒的破坏力和破坏能。结果表明:玉米的含水率越大,经过碰撞后破碎率越小;不同含水率的玉米,经过溜槽下落碰撞的平均破碎率是3.84

  19. 立筒仓机械通风安全储粮技术应用%APPLICATION OF MECHANICAL VENTILATION SAFETY STORAGE TECHNOLOGY IN SILOS

    Institute of Scientific and Technical Information of China (English)

    谢维治; 黄思华; 何育通

    2012-01-01

    The height of the grain in silos is 10 meters high above, storage performance Inferior to house type warehouse, poor stability, quality changes of obvious characteristics such as, even Easy to have "hang wall" phenomenon, especially in the southern coastal regions of high temperature and high humidity, summer long and winter short, without snow and frost free. So it is a problem for southern grain storage staffs how to reduce grain temperature quickly in the limited low temperature period to ensure the safety of stored grain in silos for the winter. By using 3 kW of local ventilator aspirating ventilation technology, corn safe storage in silos is realized.%针对立筒仓堆高十几米以上,储粮性能不如房式仓理想,稳定性较差,品质变化明显等特点,甚至容易出现“挂壁”现象,特别在南方沿海高温高湿地区,夏长冬短,无雪无霜,如何在有限的低温期快速降低粮温,确保立筒仓储粮安全过冬更是南方地区粮食储藏工作者面临的难题。广东省储备粮管理总公司珠海直属库通过立筒仓储存玉米生产性应用试验,运用3kW的局部处理通风机吸出式通风技术实现了立筒仓安全储存玉米的目的。

  20. Dismantling the Justice Silos: avoiding the pitfalls and reaping the benefits of information-sharing between forensic science, medicine and law.

    Science.gov (United States)

    Kelty, Sally F; Julian, Roberta; Ross, Alastair

    2013-07-10

    Forensic science is increasingly relied on by police and the courts to exonerate the innocent and to establish links to crime. With this increased reliance the potential for unjust outcomes increases, especially in serious matters for two reasons. The more serious the matter, the more likely that evidence mishandling can lead to wrongful imprisonment, and the more likely the personnel involved will be multi-disciplinary (police, medicine, law, forensic science), and multi-organisational (Health, Justice, private legal/medical, police). The importance of identifying effective multi-organisational interactions was highlighted in the recent wrongful imprisonment of an Australian male for a sexual assault he did not commit. One factor that led to this unjust outcome was the justice silo effect: where forensic practitioners from different agencies operate in isolation (rarely communicating or sharing information/knowledge). In this paper we discuss findings from the Interfaces Project designed to assess the extent of the justice silos within Australia. We interviewed 103 police, forensic scientists, lawyers, judges, coroners, pathologists and forensic physicians Australian-wide. Five main themes were identified in the data: the silo effect was only partial and in each jurisdiction some form of inter-agency communication was actively occurring; inter-agency meetings were more common in homicide than sexual assault cases; forensic physicians were semi-invisible; there had been considerable momentum over the past ten years for practice improvement groups, and; practitioners gain more benefits than pitfalls from inter-agency information-sharing. Based on these findings, five recommendations are made for improving practice.