WorldWideScience

Sample records for plasma-sprayed mullite 3al2o3

  1. Study on Drying Process of 3Al2O3·2SiO2 Mullite Gel

    Institute of Scientific and Technical Information of China (English)

    SONG Hui-feng; KANG Zhuang; GU Li-xia

    2008-01-01

    Monophasic mullite gel with composition 3Al2Q3·2SiO2 was prepared by the sol-gel method using aluminium nitrate nonahydrate, aluminium-tri-isopropoxide, and tetraethylorthosili-cate as reagents.Gels with different drying control chemical additives ( DCCAs ) and polyvinylpyrrolidone(PVP) as spinning assistant were dried at several temperatures.The influences of temperature.DCCAs and PVP in the drying process were investigated.N, N-dimethylformamide(DMF) was the optimum DCCA at 70℃ in the drying process.PVP decreased the solvent volatilization speed and prevented gel crack to a certain extent.FTIR results revealed that free water, ethanol, and isopropanol were completely removed by the drying procedure.

  2. Mullite Plasma Spraying for In Situ Repair of Cracks in Mullite Refractories: Simultaneous Optimization of Porosity and Thickness by Statistical Design of Experiments

    Science.gov (United States)

    Schrijnemakers, A.; Francq, B. G.; Cloots, R.; Vertruyen, B.; Boschini, F.

    2013-10-01

    We report a laboratory-scale study about the suitability of the plasma spraying process for "in situ" repair of cracks in mullite refractories of industrial furnaces. The "design of experiments" approach is used to investigate how the coating porosity and thickness are influenced by six experimental parameters. Arc current, secondary gas (H2) flow rate, and stand-off distance are the most significant parameters for both responses. Several interaction terms also affect significantly the thickness response. The validity of the model equations is discussed both from a statistical point of view and regarding the physical credibility of the main model terms. Additional experiments confirm that the measured properties lie into the prediction intervals provided by the model. Using a set of parameters optimized for minimal porosity and high thickness (relevant for the crack repair application), coatings with 6% porosity and 1070 μm thickness can be prepared reproducibly.

  3. Postperovskite phase equilibria in the MgSiO3-Al2O3 system.

    Science.gov (United States)

    Tsuchiya, Jun; Tsuchiya, Taku

    2008-12-09

    We investigate high-P,T phase equilibria of the MgSiO(3)-Al(2)O(3) system by means of the density functional ab initio computation methods with multiconfiguration sampling. Being different from earlier studies based on the static substitution properties with no consideration of Rh(2)O(3)(II) phase, present calculations demonstrate that (i) dissolving Al(2)O(3) tends to decrease the postperovskite transition pressure of MgSiO(3) but the effect is not significant ( approximately -0.2 GPa/mol% Al(2)O(3)); (ii) Al(2)O(3) produces the narrow perovskite+postperovskite coexisting P,T area (approximately 1 GPa) for the pyrolitic concentration (x(Al2O3) approximately 6 mol%), which is sufficiently responsible to the deep-mantle D'' seismic discontinuity; (iii) the transition would be smeared (approximately 4 GPa) for the basaltic Al-rich composition (x(Al2O3) approximately 20 mol%), which is still seismically visible unless iron has significant effects; and last (iv) the perovskite structure spontaneously changes to the Rh(2)O(3)(II) with increasing the Al concentration involving small displacements of the Mg-site cations.

  4. Synthesis of Monolithic Fe2O3-Al2O3 Composite Aerogels via Organic Solvent Sublimation Drying

    Directory of Open Access Journals (Sweden)

    Lili Ren

    2016-01-01

    Full Text Available Monolithic Fe2O3-Al2O3 composite aerogels have been prepared successfully via organic solvent sublimation drying method. The results show that a new phase forms when the right amount of ferric oxide is added to the alumina aerogel. From the TEM pictures we can see a shuttle-type structure with the length of about 15 nm forms, which leads to the high surface areas of composited aerogel.

  5. Study on thermal expansion behavior of Dy2O3- Al2O3- SiO2 glass

    Institute of Scientific and Technical Information of China (English)

    LIU Yuzhu; GENG Zhiting; ZHUANG Weidong; HE Huaqiang

    2008-01-01

    Employing Dy2O3, Al2O3, and SiO2 as starting materials, several series of Dy2O3-Al2O3-SiO2 sealing glass were prepared. The relationship between their coefficients of thermal expansion and the contents of Dy2O3, Al2O3, and SiO2 were studied respectively. Experimental results showed that Dy2O3 and Al2O3 had a positive effect on the coefficient of thermal expansion of glass, whereas, SiO2 had a negative effect. The coefficient of thermal expansion of glass showed an apparent linear relation to the contents of these three raw materials, from which an estimation model was built, to calculate the coefficient of thermal expansion of sealing glass. Relative errors of the calculating resalts to testing results were no more than 2%, which suggested that the estimation model was reasonable. This study provides a good theory reference for the practical utilizing of this sealing material, through which a proper glass composition for good sealing could be easily found.

  6. Potential of LiNO3/Al2O3 Catalyst for Heterogeneous Transesterification of Palm Oil to Biodiesel

    Directory of Open Access Journals (Sweden)

    Istadi Istadi

    2010-10-01

    Full Text Available Production of biodiesel through transesterification process using heterogenous catalysts in order to avoid the saponification problem was studied. In this process, palm oil reacted with methanol to form a mixture of glycerol and biodiese over a solid basic catalyst. One type of the catalysts used in this research is basic catalyst of LiNO3/Al2O3. The parameters studied in this research are concentration of LiNO3 loading on Al2O3 and effect of different reaction time. The products was analyzed using Gas Chromatography to determine composition and yield of resulted methyl esters as well as conversion of palm oil to biodiesel. The major products in this transesterification reaction were biodiesel and glycerol. It can be concluded that the 20 wt% LiNO3/Al2O3 catalyst is potential for producing biodiesel from palm oil over transesterification reaction. Advantages of the usage of this catalyst is that the soap formation was not observed in this research. ©2010 BCREC UNDIP. All rights reserved(Received: 24th April 2010, Revised: 20th May 2010; Accepted: 21st May 2010[How to Cite: I. Istadi, B. Pramudono, S. Suherman, and S. Priyanto. (2010. Potential of LiNO3/Al2O3 Catalyst for Heterogeneous Transesterification of Palm Oil to Biodiesel. Bulletin of Chemical Reaction Engineering and Catalysis, 5(1: 51-56. doi:10.9767/bcrec.5.1.7128.51-56][How to Link / DOI: http://dx.doi.org/10.9767/bcrec.5.1.7128.51-56

  7. Role of Tricoordinate Al Sites in CH3ReO3/Al2O3 Olefin Metathesis Catalysts.

    Science.gov (United States)

    Valla, Maxence; Wischert, Raphael; Comas-Vives, Aleix; Conley, Matthew P; Verel, René; Copéret, Christophe; Sautet, Philippe

    2016-06-01

    Re2O7 supported on γ-alumina is an alkene metathesis catalyst active at room temperature, compatible with functional groups, but the exact structures of the active sites are unknown. Using CH3ReO3/Al2O3 as a model for Re2O7/Al2O3, we show through a combination of reactivity studies, in situ solid-state NMR, and an extensive series of DFT calculations, that μ-methylene structures (Al-CH2-ReO3-Al) containing a Re═O bound to a tricoordinated Al (AlIII) and CH2 bound to a four-coordinated Al (AlIVb) are the precursors of the most active sites for olefin metathesis. The resting state of CH3ReO3/Al2O3 is a distribution of μ-methylene species formed by the activation of the C-H bond of CH3ReO3 on different surface Al-O sites. In situ reaction with ethylene results in the formation of Re metallacycle intermediates, which were studied in detail through a combination of solid-state NMR experiments, using labeled ethylene, and DFT calculations. In particular, we were able to distinguish between metallacycles in TBP (trigonal-bipyramidal) and SP (square-pyramidal) geometry, the latter being inactive and detrimental to catalytic activity. The SP sites are more likely to be formed on other Al sites (AlIVa/AlIVa). Experimentally, the activity of CH3ReO3/Al2O3 depends on the activation temperature of alumina; catalysts activated at or above 500 °C contain more active sites than those activated at 300 °C. We show that the dependence of catalytic activity on the Al2O3 activation temperature is related to the quantity of available AlIII-defect sites and adsorbed H2O.

  8. Potential of LiNO3/Al2O3 Catalyst for Heterogeneous Transesterification of Palm Oil to Biodiesel

    Directory of Open Access Journals (Sweden)

    Bambang Pramudono

    2010-10-01

    Full Text Available Production of biodiesel through transesterification process using heterogenous catalysts in order to avoid the saponification problem was studied. In this process, palm oil reacted with methanol to form a mixture of glycerol and biodiese over a solid basic catalyst. One type of the catalysts used in this research is basic catalyst of LiNO3/Al2O3. The parameters studied in this research are concentration of LiNO3 loading on Al2O3 and effect of different reaction time. The products was analyzed using Gas Chromatography to determine composition and yield of resulted methyl esters as well as conversion of palm oil to biodiesel. The major products in this transesterification reaction were biodiesel and glycerol. It can be concluded that the 20 wt% LiNO3/Al2O3 catalyst is potential for producing biodiesel from palm oil over transesterification reaction. Advantages of the usage of this catalyst is that the soap formation was not observed in this research. ©2010 BCREC UNDIP. All rights reserved(Received: 24th April 2010, Revised: 20th May 2010; Accepted: 21st May 2010[How to Cite: I. Istadi, B. Pramudono, S. Suherman, and S. Priyanto. (2010. Potential of LiNO3/Al2O3 Catalyst for Heterogeneous Transesterification of Palm Oil to Biodiesel. Bulletin of Chemical Reaction Engineering and Catalysis, 5(1: 51-56. doi:10.9767/bcrec.5.1.777.51-56][How to Link / DOI: http://dx.doi.org/10.9767/bcrec.5.1.777.51-56

  9. Formation of a 25 mol% Fe2O3-Al2O3 solid solution prepared by ball milling

    DEFF Research Database (Denmark)

    Jiang, Jianzhong; Mørup, Steen; Linderoth, Søren

    1996-01-01

    The phase transformation process of a 25 mol% Fe2O3-Al2O3 powder mixture during high-energy ball milling has been studied by x-ray diffraction and Mossbauer spectroscopy. A metastable solid solution of 25 mol % Fe2O3 in Al2O3 with corundum structure has successfully been prepared after a milling...... time of 122 h. This demonstrates that the high-energy ball milling technique is able to prepare metastable solid solutions with an extended range of compositions in ceramic/ceramic systems with a positive hear of mixing....

  10. Adhesion of Y2O3-Al2O3-SiO2 coatings to typical aerospace substrates

    Energy Technology Data Exchange (ETDEWEB)

    Marraco-Borderas, C.; Nistal, A.; Garcia, E.; Sainz, M.A.; Martin de la Escalera, F.; Essa, Y.; Miranzo, P.

    2016-07-01

    High performance lightweight materials are required in the aerospace industry. Silicon carbide, carbon fiber reinforced carbon and slicon carbide composites comply with those requirements but they suffer from oxidation at the high temperature of the service conditions. One of the more effective approaches to prevent this problem is the use of protecting ceramic coatings, where the good adhesion between substrates and coatings are paramount to guarantee the optimal protection performance. In the present work, the adhesion between those substrates and glass coatings of the Y2O3-Al2O3-SiO2 system processed by oxyacetylene flame spraying is analyzed. Increasing load scratch tests are employed for determining the failure type, maximum load and their relation with the elastic and mechanical properties of the coatings. The results points to the good adhesion of the coatings to silicon carbide and carbon fibre reinforced silicon carbide while the carbon fiber reinforced carbon is not a suitable material to be coated. (Author)

  11. Mullite Whiskers and Mullite-whisker Felt

    Science.gov (United States)

    Talmy, Inna G.; Haught, Deborah A.

    1993-01-01

    The Naval Surface Warfare Center has developed processes for the preparation of mullite (3(Al2O3)(dot)2(SiO2)) whiskers and mullite-whisker felt. Three patents on the technology were issued in 1990. The processes are based on chemical reactions between AlF3, Al2O3, and SiO2. The felt is formed in-situ during the processing of shaped powdered precursors. It consists of randomly oriented whiskers which are mutually intergrown forming a rigid structure. The microstructure and properties of the felt and size of the whiskers can be modified by varying the amount of Al2O3 in the starting mixture. Loose mullite whiskers can be used as a reinforcement for polymer-, metal-, and ceramic-matrix composites. The felt can be used as preforms for fabricating composite materials as well as for thermal insulation and high temperature, chemically stable filters for liquids (melts) and gases.

  12. Dilatometric studies of (SiO2-RE2O3-Al2O3 silicon carbide ceramics

    Directory of Open Access Journals (Sweden)

    Juliana Marchi

    2005-06-01

    Full Text Available Silicon carbide is an important structural ceramic and finds applications as abrasives, as a refractory and in automotive engine components. This material can attain high densities during liquid phase sintering if suitable additives are used. Silicon carbides containing silica, alumina and rare earth oxides have suitable characteristics to promote liquid phase sintering. In this paper, the sintering behavior of silicon carbide ceramics with additives based on the (SiO2-RE2O3-Al2O3 system (RE = Y, Dy has been studied. Samples with different compositions and containing 90 vol.% SiC were sintered in a dilatometer at 1950 °C/1h and in a graphite resistance furnace from 1500 °C/1h up to 1950 °C/1h. The shrinkage behavior as a function of rare earth oxide used and additive composition was also studied. The sintered materials were characterized by density and weight loss measurements. The crystalline phases were identified by X-ray diffraction analysis. The sintering kinetics of these materials can be related to the formation of secondary crystalline phases.

  13. Effect of Processing Parameters on Thermal Cycling Behavior of Al2O3-Al2O3 Brazed Joints

    Science.gov (United States)

    Dandapat, Nandadulal; Ghosh, Sumana; Guha, Bichitra Kumar; Datta, Someswar; Balla, Vamsi Krishna

    2016-10-01

    In the present study, alumina ceramics were active metal brazed at different temperatures ranging from 1163 K to 1183 K (890 °C to 910 °C) using TICUSIL (68.8Ag-26.7Cu-4.5Ti in wt pct) foil as filler alloy of different thicknesses. The brazed joints were subjected to thermal cycling for 100 cycles between 323 K and 873 K (50 °C and 600 °C). The microstructural and elemental composition analysis of the brazed joints were performed by scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) before and after thermal cycling. Helium (He) leak test and brazing strength measurement were also conducted after thermal cycling for 100 cycles. The joint could withstand up to 1 × 10-9 Torr pressure and brazing strength was higher than 20 MPa. The experimental results demonstrated that joints brazed at the higher temperature with thinner filler alloy produced strong Al2O3-Al2O3 joints.

  14. Application of Fe2O3/Al2O3 Composite Particles as Oxygen Carrier of Chemical Looping Combustion

    Institute of Scientific and Technical Information of China (English)

    Fang He; Hua Wang; Yongnian Dai

    2007-01-01

    Chemical looping combustion (CLC) of carbonaceous compounds has been proposed, in the past decade, as an efficient method for CO2 capture without cost of extra energy penalties. The technique involves the use of a metal oxide as an oxygen carrier that transfers oxygen from combustion air to fuels.The combustion is carried out in a two-step process: in the fuel reactor, the fuel is oxidized by a metal oxide, and in the air reactor, the reduced metal is oxidized back to the original phase. The use of iron oxide as an oxygen carrier has been investigated in this article. Particles composed of 80 wt% Fe2O3,together with Al2O3 as binder, have been prepared by impregnation methods. X-ray diffraction (XRD) analysis reveals that Fe2O3 does not interact with the Al2O3 binder after multi-cycles. The reactivity of the oxygen carrier particles has been studied in twenty-cycle reduction-oxidation tests in a thermal gravimetrical analysis (TGA) reactor. The components in the outlet gas have been analyzed. It has been observed that about 85% of CH4 converted to CO2 and H2O during most of the reduction periods. The oxygen carrier has kept quite a high reactivity in the twenty-cycle reactions. In the first twenty reaction cycles, the reaction rates became slightly higher with the number of cyclic reactions increasing, which was confirmed by the scanning electron microscopy (SEM) test results. The SEM analysis revealed that the pore size inside the particle had been enlarged by the thermal stress during the reaction, which was favorable for diffusion of the gaseous reactants into the particles. The experimental results suggested that the Fe2O3/Al2O3 oxygen carrier was a promising candidate for a CLC system.

  15. TiC Particle Reinforced Silicon Nitride Composite Joined With Y2O3-Al2O3-SiO2 Mixture

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Silicon nitride composite is joined to itself by heating interlayer of Y2O3-Al2O3-SiO2 mixtures above their liquidus temperatures in flowing nitrogen. The joined specimens are tested in four point flexure from room temperature to 1373K. The interface microstructure and fractured surfaces after testing are observed and analyzed by SEM, EPMA and XRD respectively. The results show that Y2O3-Al2O3-SiO2 glass reacts with Si3N4 at interface, forming the Si3N4/Si2N2O(Y-Al-Si-O-N glass/ Y-Al-Si-O glass gradient interface. With the increase of bonding temperature and holding time, the joint strength first increases, reaching a peak, and then decreases.According to interfacial analyses, the bonding strength depends on joint thickness.

  16. The mechanism of pyridine hydrogenolysis on molybdenum-containing catalysts : I. The monolayer MoO3-Al2O3 catalyst: Preparation and catalytic properties

    NARCIS (Netherlands)

    Sonnemans, J.; Mars, P.

    1973-01-01

    Preparation of a MoO3-Al2O3 catalyst with a monolayer of molybdenum oxide on the alumina was possible by adsorbing MoO2(OH)2 at 600°C from the gas phase. From the amounts of molybdenum adsorbed and the surface areas of the catalysts a characteristic value of 17Å2 was calculated for the area occupied

  17. Oxidation Resistance of Fe-13Cr Alloy with Micro-Laminated (ZrO2-Y2O3)/(Al2O3-Y2O3) Films

    Institute of Scientific and Technical Information of China (English)

    Yao Mingming; He Yedong; Wang Deren; Gao Wei

    2005-01-01

    The micro-laminated (ZrO2-Y2O3)/(Al2O3-Y2O3) composite films were prepared on the surface of Fe-13Cr alloy by an electrochemical process and a sintering process alternately. High-resolution field emission scanning electron microscopy (FE-SEM) was used to characterize the laminated films, indicating that the micro-laminated (ZrO2-Y2O3)/(Al2O3-Y2O3) films have nano-structures. SEM, EDS and mass gain measurement were adopted to study the oxidation resistance of films on Fe-13Cr alloy. It is proved that such micro-laminated films are more effective than ZrO2-Y2O3 or Al2O3-Y2O3 films to resist the oxidation of the alloy, and the oxidation resistance is increased with increasing layers in micro-laminated films. These beneficial effects can be contributed to the mechanism, by which such micro-laminated (ZrO2-Y2O3)/(Al2O3-Y2O3) composite film combines all the beneficial effects and overcomes all the disadvantages of both ZrO2-Y2O3 film and Al2O3-Y2O3 film during oxidation of alloy.

  18. Effect of Ultrasonic Vibration on the Behavior of Antifriction and Wear Resistance of Al2O3/Al2O3 Ceramic Friction Pairs Under Oil Lubrication

    Science.gov (United States)

    Dong, X. Y.; Qiao, Y. L.; Zang, Y.; Cui, Q. S.

    The behavior of antifriction and wear resistance of Al2O3/Al2O3 ceramic friction pairs lubricated by four different lubrication oils under ultrasonic vibration was studied. The surface morphologies of wear scare was analyzed by metallographic microscope. The effect mechanism of ultrasonic vibration on frictional pairs under different lubrication oils was discussed. The studied results showed that, ultrasonic vibration would improve the behavior of antifriction and wear resistance of the Al2O3/Al2O3 ceramic friction pairs under various lubrication oils.The improving would be dramaticer when the viscosity of lubrication oil was low. Ultrasonic vibration decreased the friction coefficient and wear volume 12.9% and 38.7% respectively, when the lubrication oil was 6#,the viscosity of which is 39.77 mm2/s. When the lubrication oil was 150BS, the viscosity of which is 549.69 mm2/s, ultrasonic vibration made friction coefficient and wear volume decreased 4.6% and 11.6% respectively.The effect of ultrasonic vibration on the behavior of antifriction and wear resistance of Al2O3/Al2O3 ceramic friction pairs was determined by the formation and the destruction of oil film on the friction surface and the upward floatage created by ultrasonic vibration.

  19. Key Durability Issues with Mullite-Based Environmental Barrier Coatings for Si-Based Ceramics

    Science.gov (United States)

    Lee, Kang N.

    2000-01-01

    Plasma-sprayed mullite (3Al2O3.2SiO2) and mullite/yttria-stabilized-zirconia (YSZ) dual layer coatings have been developed to protect silicon -based ceramics from environmental attack. Mullite-based coating systems show excellent durability in air. However, in combustion environments, corrosive species such as molten salt or water vapor penetrate through cracks in the coating and attack the Si-based ceramics along the interface. Thus the modification of the coating system for enhanced crack-resistance is necessary for long-term durability in combustion environments. Other key durability issues include interfacial contamination and coating/substrate bonding. Interfacial contamination leads to enhanced oxidation and interfacial pore formation, while a weak coating/substrate bonding leads to rapid attack of the interface by corrosive species, both of which can cause a premature failure of the coating. Interfacial contamination can be minimized by limiting impurities in coating and substrate materials. The interface may be modified to improve the coating/substrate bond.

  20. Key Durability Issues with Mullite-Based Environmental Barrier Coatings for Si-Based Ceramics

    Science.gov (United States)

    Lee, Kang N.

    2000-01-01

    Plasma-sprayed mullite (3Al2O3.2SiO2) and mullite/yttria-stabilized-zirconia (YSZ) dual layer coatings have been developed to protect silicon -based ceramics from environmental attack. Mullite-based coating systems show excellent durability in air. However, in combustion environments, corrosive species such as molten salt or water vapor penetrate through cracks in the coating and attack the Si-based ceramics along the interface. Thus the modification of the coating system for enhanced crack-resistance is necessary for long-term durability in combustion environments. Other key durability issues include interfacial contamination and coating/substrate bonding. Interfacial contamination leads to enhanced oxidation and interfacial pore formation, while a weak coating/substrate bonding leads to rapid attack of the interface by corrosive species, both of which can cause a premature failure of the coating. Interfacial contamination can be minimized by limiting impurities in coating and substrate materials. The interface may be modified to improve the coating/substrate bond.

  1. Research on Glass Forming Ability of Er2O3 -Al2O3 -B2O3 -SiO2 System

    Institute of Scientific and Technical Information of China (English)

    Zhang Qitu; Fu Zhenxiao; Ni Yaru; Lu Chunhua; Xu Zhongzi

    2004-01-01

    The glass forming range of Er2O3-Al2O3-B2O3-SiO2 system was explored, and the effect of the content of Al2 O3 and Er2 O3 on glass-forming region was experimentally examined. It is shown that the region of glass formation range expends when the content of Al2O3 is changed from 15% to 20%, while it shrinks when the content of Er2O3 is changed from 20% to 30%. At the same time, the glass forming ability of Er2O3-Al2O3-B2O3-SiO2 system was also discussed using a value of β, which is an indication of crystallization tendency of glasses, calculated from thermo-analysis data. It is found that the glass forming ability of Er2O3-Al2O3-B2O3- SiO2 glasses is poor, while the glasses network may be enhanced when Al2O3 is added to the system, the glass forming ability being heightened. In addition, the crystallization temperatures of the rare earth glasses were determined using differential thermal analysis technique. The Er2O3-Al2O;-B2O3-SiO2 glass samples were heat treated at 1000,1100 and 1260℃ respectively. The results show that it is the Er2O3 phase that separates out from the glasses after crystaline heat treatment, and it is tiered up in glasses, as detected through XRD and SEM. This indicates that the phase separation occurs when the glasses are heated, Er3+ being mainly distributed in the boron rich phase, then separated out from glasses, while the silicate rich phase remaining glassy state.

  2. Tenacidad a la fractura de compuestos cermets 3Al2O3*2SiO2/Ag manufacturados por molienda de alta energía

    OpenAIRE

    Hernández,José G. Miranda; Bustamante,Miriam Vázquez; Hernández,Héctor Herrera; Morán,Carlos O. González; Rangel,Enrique Rocha; García,Elizabeth Refugio

    2016-01-01

    La fabricación de materiales compuestos de matriz cerámica reforzados con partículas metálicas han propiciado la formación de nuevos materiales conocidos como compuestos CERMETS, materiales que debido a sus elementos precursores poseen propiedades distintas a las de los materiales convencionales. En este trabajo se establece la ruta de fabricación de materiales compuestos cermets base 3Al2O3*2SiO2 reforzados con partículas metálicas de Ag a partir de la formación de la composición química en ...

  3. Oxidation of primary amines to oximes with molecular oxygen using 1,1-diphenyl-2-picrylhydrazyl and WO3/Al2O3 as catalysts.

    Science.gov (United States)

    Suzuki, Ken; Watanabe, Tomonari; Murahashi, Shun-Ichi

    2013-03-15

    The oxidative transformation of primary amines to their corresponding oximes proceeds with high efficiency under molecular oxygen diluted with molecular nitrogen (O2/N2 = 7/93 v/v, 5 MPa) in the presence of the catalysts 1,1-diphenyl-2-picrylhydrazyl (DPPH) and tungusten oxide/alumina (WO3/Al2O3). The method is environmentally benign, because the reaction requires only molecular oxygen as the terminal oxidant and gives water as a side product. Various alicyclic amines and aliphatic amines can be converted to their corresponding oximes in excellent yields. It is noteworthy that the oxidative transformation of primary amines proceeds chemoselectively in the presence of other functional groups. The key step of the present oxidation is a fast electron transfer from the primary amine to DPPH followed by proton transfer to give the α-aminoalkyl radical intermediate, which undergoes reaction with molecular oxygen and hydrogen abstraction to give α-aminoalkyl hydroperoxide. Subsequent reaction of the peroxide with WO3/Al2O3 gives oximes. The aerobic oxidation of secondary amines gives the corresponding nitrones. Aerobic oxidative transformation of cyclohexylamines to cyclohexanone oximes is important as a method for industrial production of ε-caprolactam, a raw material for Nylon 6.

  4. Luminescence and energy transfer of Tb(3+)-doped BaO-Gd2O3-Al2O3-B2O3-SiO2 glasses.

    Science.gov (United States)

    Zuo, Chenggang; Huang, Jinze; Liu, Shaoyou; Xiao, Anguo; Shen, Youming; Zhang, Xiangyang; Zhou, Zhihua; Zhu, Ligang

    2017-12-05

    Transparent Tb(3+)-doped BaO-Gd2O3-Al2O3-B2O3-SiO2 glasses with the greater than 4g/cm(3) were prepared by high temperature melting method and its luminescent properties have been investigated by measured UV-vis transmission, excitation, emission and luminescence decay spectra. The transmission spectrum shows there are three weak absorption bands locate at about 312, 378 and 484nm in the glasses and it has good transmittance in the visible spectrum region. Intense green emission can be observed under UV excitation. The effective energy transfer from Gd(3+) ion to Tb(3+) ion could occur and sensitize the luminescence of Tb(3+) ion. The green emission intensity of Tb(3+) ion could change with the increasing SiO2/B2O3 ratio in the borosilicate glass matrix. With the increasing concentration of Tb(3+) ion, (5)D4→(7)FJ transitions could be enhanced through the cross relaxation between the two nearby Tb(3+) ions. Luminescence decay time of 2.12ms from 546nm emission is obtained. The results indicate that Tb(3+)-doped BaO-Gd2O3-Al2O3-B2O3-SiO2 glasses would be potential scintillating material for applications in X-ray imaging. Copyright © 2017 Elsevier B.V. All rights reserved.

  5. Electrical conductivity of (Na3AlF6-40%K3AlF6)-AlF3-Al2O3 melts

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    The effects of contents of AlF3 and Al2O3,and temperature on electrical conductivity of (Na3AlF6-40%K3AlF6)-AlF3-Al2O3 were studied by continuously varying cell constant (CVCC) technique.The results show that the conductivities of melts increase with the increase of temperature,but by different extents.Every increasing 10 ℃ results in an increase of 1.85×10-2,1.86×10-2,1.89×10-2 and 2.20×10-2 S/cm in conductivity for the (Na3AlF6-40%K3AlF6)-AlF3 melts containing 0%,20%,24%,and 30% AlF3,respectively.An increase of every 10 ℃ in temperature results an increase about 1.89×10-2,1.94×10-2,1.95×10-2,1.99×10-2 and 2.10×10-2 S/cm for (Na3AlF6-40%K3AlF6)-AlF3-Al2O3 melts containing 0%,1%,2%,3% and 4% A12O3,respectively.The activation energy of conductance was calculated based on Arrhenius equation.Every increasing 1% of AlF3 results in a decrease of 0.019 and 0.020 S/cm in conductivity for (Na3AlF6-40%K3AlF6)-AIF3 melts at 900 and 1 000 ℃,respectively.Every increase of 1% Al2O3 results in a decrease of 0.07 S/cm in conductivity for (Na3AlF6-40%K3AlF6)-AlF3-Al2O3 melts.The activation energy of conductance increases with the increase in content of AlF3 and Al2O3.

  6. Characterization of gamma-Ga2O3-Al2O3 prepared by solvothermal method and its performance for methane-SCR of NO.

    Science.gov (United States)

    Nakatani, Tetsu; Watanabe, Tsunenori; Takahashi, Masaru; Miyahara, Yuya; Deguchi, Hiroshi; Iwamoto, Shinji; Kanai, Hiroyoshi; Inoue, Masashi

    2009-06-25

    The gamma-Ga(2)O(3)-Al(2)O(3) mixed oxides with a spinel structure were prepared by the solvothermal reaction of gallium acetylacetonate and aluminum isopropoxide in diethylenetriamine. In the crystal structures of the catalysts obtained by the calcination of these mixed oxides, Ga(3+) and Al(3+) ions preferentially occupied tetrahedral and octahedral sites, respectively. The catalysts with low Ga contents had a unique structure with high surface areas and a concentration gradient of decreasing Ga content from the surface to the bulk. In methane-selective catalytic reduction (SCR) of NO, higher NO conversion to N(2) was attained on the catalyst with high occupation of Ga(3+) ions at tetrahedral sites and Al(3+) ions at octahedral sites. For the gamma-Ga(2)O(3)-Al(2)O(3) mixed oxide with a charged Ga molar content of 0.3 (ST(0.3)), tetrahedral and octahedral sites were solely occupied by Ga(3+) and Al(3+) ions, respectively, and the catalyst exhibited the highest NO conversion to N(2). Therefore, it was concluded that the active site for methane-SCR of NO is tetrahedral Ga(3+) ion and octahedral Al(3+) ion, which are linked to each other. Nitrogen monoxide is adsorbed on the isolated hydroxyl group attached to Al(3+) ions and then oxidized by O(2) yielding surface nitrate species. Tetrahedral Ga(3+) ions work as Lewis acid sites for the activation of methane because of their coordinative unsaturation. The Ga(3+) ions in the gamma-Ga(2)O(3)-Al(2)O(3) catalyst have a redox property, which plays important roles in both the oxidation of NO to surface nitrate species and the activation of methane. The most important factor for this catalyst is that the sites for the formation of surface nitrate species reside next to the methane activation sites, which facilitates the reaction between surface nitrate species and the activated species derived from methane, thus mitigating the consumption of methane by simple combustion with O(2). Therefore, ST(0.3), which has the largest

  7. Fe2O3-Al2O3-SiO2-TiO2抗菌、纳米湿敏陶瓷薄膜的Sol-Gel制备%PREPARATION OF Fe2O3-Al2O3-SiO2-TiO2 ANTIBACTERIAL NANOMETRE HUMIDITY SENSITIVE CERAMIC MEMBRANES BY SOL-GEL PROCESSING

    Institute of Scientific and Technical Information of China (English)

    刘儒平; 俞康泰

    2005-01-01

    利用溶胶凝胶法制成了Fe2O3-Al2O3-SiO2-TiO2抗菌、纳米湿敏陶瓷薄膜.用扫描电镜和原子力显微镜对膜的表面形貌和显微结构进行表征,分析了处理方式对膜的表面形貌和微观结构的影响.制成的Fe2O3-Al2O3-SiO2-TiO2抗菌、纳米湿敏陶瓷薄膜具有广谱抗菌、高效、无毒、持久和耐热等特点.湿敏特性测试结果表明:Fe2O3-Al2O3-SiO2-TiO2抗菌、纳米陶瓷薄膜制品的感湿灵敏度高,具有较好的响应特性和稳定性.

  8. Impacts of Annealing Conditions on the Flat Band Voltage of Alternate La2O3/Al2O3 Multilayer Stack Structures

    Science.gov (United States)

    Feng, Xing-Yao; Liu, Hong-Xia; Wang, Xing; Zhao, Lu; Fei, Chen-Xi; Liu, He-Lei

    2016-09-01

    The mechanism of flat band voltage (VFB) shift for alternate La2O3/Al2O3 multilayer stack structures in different annealing condition is investigated. The samples were prepared for alternate multilayer structures, which were annealed in different conditions. The capacitance-voltage (C-V) measuring results indicate that the VFB of samples shift negatively for thinner bottom Al2O3 layer, increasing annealing temperature or longer annealing duration. Simultaneously, the diffusion of high- k material to interfaces in different multilayer structures and annealing conditions is observed by X-ray photoelectron spectroscopy (XPS). Based on the dipole theory, a correlation between the diffusion effect of La towards bottom Al2O3/Si interface and VFB shift is found. Without changing the dielectric constant k of films, VFB shift can be manipulated by controlling the single-layer cycles and annealing conditions of alternate high- k multilayer stack.

  9. The Effects of Gravity on the Combustion Synthesis of B2O3-Al2O3-MgO Glass Ceramic Composites

    Science.gov (United States)

    Manerbino, A. R.; Yi, H. C.; Guigne, J. Y.; Moore, J. J.; Schowengerdt, F. D.

    2000-01-01

    Glass ceramic composites based on B2O3-Al2O3-MgO have been produced by combustion synthesis in a Self-propagating mode. The gravitational effects on the combustion characteristics such as combustion wave velocity (V), and combustion temperature (T(sub c)) were studied. The results showed that the gravitational effects on these parameters were inconclusive. The microstructure of this system has also been analyzed with X-ray Diffraction and light microscopy. These results showed a higher amount of divitrification occurs under both reduced gravity and high gravity conditions. The gravitational effects on formation of pores, overall porosity and apparent porosity for this family of glass-ceramics also shows to be inconclusive. Possible reasons for these results are discussed.

  10. Catalytic Synthesis of Tert-Butyl Acetate by Nd2O3/Al2O3-Nd2O3/ZnO

    Institute of Scientific and Technical Information of China (English)

    Wang Yajun; Han Limin; A Shan

    2007-01-01

    Nd2O3 was used to support Al2O3 and ZnO to prepare a supported solid base catalyst and investigate the effect of catalyst and reaction conditions on the synthesis of tert-butyl acetate. The composited oxide of Nd2O3/Al2O3-Nd2O3/ZnO exhibited excellent catalytic activity for the synthsis of tert-butyl acetate. The molar ratio of tert-butanol to acetic anhydride is 3:1, the catalyst in total amount of reactant nearly 0.5%, and reaction time 6 h. With the above conditions, yield of the reaction could reach to 65%. The structure of product were verified by the FT-IR, Element analysis, and MS, which proved that the product was tert-butyl acetate.

  11. Si:SrTiO3-Al2O3-Si:SrTiO3 multi-dielectric architecture for metal-insulator-metal capacitor applications

    Science.gov (United States)

    Dugu, Sita; Pavunny, Shojan P.; Scott, James F.; Katiyar, Ram S.

    2016-11-01

    Metal-insulator-metal (MIM) capacitors comprised of amorphous Si:SrTiO3-Al2O3-Si:SrTiO3 multi-dielectric architecture have been fabricated employing a combination of pulsed laser and atomic layer deposition techniques. The voltage linearity, temperature coefficients of capacitance, dielectric and electrical properties upon thickness were studied under a wide range of temperature (200-400 K) and electric field stress (±1.5 MV/cm). A high capacitance density of 31 fF/μm2, a low voltage coefficient of capacitance of 363 ppm/V2, a low temperature coefficient of capacitance of <644 ppm/K, and an effective dielectric constant of ˜133 are demonstrated in a MIM capacitor with ˜1.4 nm capacitance equivalent thickness in a ˜40 nm thick ultra high-k multi-dielectric stack. All of these properties make this dielectric architecture of interest for next generation, highly scaled MIM capacitor applications.

  12. Effect of the Fourth Element on Bonding of Silicon Nitride Ceramics with Y2O3-Al2O3-SiO2 Glass Solders

    Institute of Scientific and Technical Information of China (English)

    周飞

    2001-01-01

    Bonding of Si3N4 ceramic was performed with Y2O3-Al2O3-SiO2(YAS)-X glass solders,which were mixed with TiO2 (YT) and Si3N4 (YN), respectively. The effects of bonding conditions and interfacial reaction on the joint strength were studied. The joint strength in different bonding conditions was measured by four-point bending tests. The interfacial microstructures were observed and analyzed by SEM, EPMA and XRD. It is shown that with the increase of bonding temperature and holding time, the joint strength increases reaching a peak, and then decreases. When TiO2 is put into YAS solder,the bonding interface with Si3N4/(Y-Sialon glass+TiN)/TiN/Y-Sialon glass is formed. When YAS solder is mixed with Si3N4 powder, the interfacial residual thermal stress may be decreased, and then the joint strength is enhanced. According to microanalyses, the bonding strength is related to interfacial reaction.

  13. High-Energy-Density Polymer Nanocomposites Composed of Newly Structured One-Dimensional BaTiO3@Al2O3 Nanofibers.

    Science.gov (United States)

    Pan, Zhongbin; Yao, Lingmin; Zhai, Jiwei; Fu, Dezhou; Shen, Bo; Wang, Haitao

    2017-02-01

    Flexible electrostatic capacitors are potentially applicable in modern electrical and electric power systems. In this study, flexible nanocomposites containing newly structured one-dimensional (1D) BaTiO3@Al2O3 nanofibers (BT@AO NFs) and the ferroelectric polymer poly(vinylidene fluoride) (PVDF) matrix were prepared and systematically studied. The 1D BT@AO NFs, where BaTiO3 nanoparticles (BT NPs) were embedded and homogeneously dispersed into the AO nanofibers, were successfully synthesized via an improved electrospinning technique. The additional AO layer, which has moderating dielectric constant, was introduced between BT NPs and PVDF matrixes. To improve the compatibility and distributional homogeneity of the nanofiller/matrix, dopamine was coated onto the nanofiller. The results show that the energy density due to high dielectric polarization is about 10.58 J cm(-3) at 420 MV m(-1) and the fast charge-discharge time is 0.126 μs of 3.6 vol % BT@AO-DA NFs/PVDF nanocomposite. A finite element simulation of the electric-field and electric current density distribution revealed that the novel-structured 1D BT@AO-DA NFs significantly improved the dielectric performance of the nanocomposites. The large extractable energy density and high dielectric breakdown strength suggest the potential applications of the BT@AO-DA NFs/PVDF nanocomposite films in electrostatic capacitors and embedded devices.

  14. Effect of CuO addition on the sintering temperature and microwave dielectric properties of CaSiO3-Al2O3 ceramics

    Institute of Scientific and Technical Information of China (English)

    Denghao Li; Huanping Wang; Zuopeng He; Zhen Xiao; Ruoshan Lei; Shiqing Xu

    2014-01-01

    CuO-doped CaSiO3-1 wt% Al2O3 ceramics were synthesized via a traditional solid-state reaction method, and their sintering behavior, microstructure and microwave dielectric properties were investigated. The results showed that appropriate CuO addition could accelerate the sintering process and assist the densification of CaSiO3-1 wt%Al2O3 ceramics, which could effectively lower the densification temperature from 1250 1C to 1050 1C. However, the addition of CuO undermined the microwave dielectric properties. The optimal amount of CuO addition was found to be 0.8 wt%, and the derived CaSiO3-Al2O3 ceramic sintered at 1100 1C presented good microwave dielectric properties ofεr ¼ 7.27, Q ? f ¼ 16,850 GHz andτf ¼ ? 39.53 ppm/1C, which is much better than those of pure CaSiO3 ceramic sintered at 1340 oC (Q ? f ¼ 13,109 GHz). The chemical compatibility of the above ceramic with 30 Pd/70 Ag during the cofiring process has also been investigated, and the result showed that there was no chemical reaction between palladium-silver alloys and ceramics.

  15. Influence of CaCO3, Al2O3, and TiO2 microfillers on physico-mechanical properties of Luffa cylindrica/polyester composites

    Directory of Open Access Journals (Sweden)

    Vinay Kumar Patel

    2016-06-01

    Full Text Available The development of natural fibre reinforced polymer composites has gained popularity in many applications due to their environment friendly characteristics over the synthetic fibre based polymer composites. This paper describes the fabrication and physical, mechanical, three-body abrasive wear and water absorption behaviour of Luffa fibre reinforced polyester composites with and without addition of micro-fillers of Al2O3, CaCO3 and TiO2. The ranking of the composite materials has been made by using Technique for order preference by similarity to ideal solution (TOPSIS method with output parameters of their physical, mechanical and abrasive wear and water absorption attributes. The addition of microfillers has enhanced greatly the physical and mechanical properties of Luffa-fibre based composites. The addition of microfillers has influenced the physico-mechanical properties of Luffa-fibre based polyester composites in descending order of CaCO3, Al2O3, and TiO2.

  16. Influence of Cr2O3-Al2O3 Composite Oxide Scale on Oxidation Resistance of ZG40Cr24

    Institute of Scientific and Technical Information of China (English)

    WANG Haitao; JIANG Peigang; HUANG Liping

    2012-01-01

    Test alloys ZG40Cr24 with alloying of 3 wt% aluminium were cast by intermediate frequency induction furnace.The oxidation resistance of test alloys at 1 000 ℃ for 500 hours was examined according to oxidation weight gain method.The scale morphology and composition were studied using scanning electron microscope (SEM) and X-ray diffraction (XRD) respectively.By energy dispersive spectroscopy (EDS) studies,a kind of composite oxide scale compounded highly by Cr2O3,Al2O3 and spinel MCr2O4 in molecule scale came into being at high temperature.With flat and compact structure,fine and even grains,such composite scale granted complete oxidation resistance to alloy ZG40Cr24.The oxidation resistance mechanism was studied deeply in electrochemistry corrosion.The P+N semiconductor composite scale composed plenty of inner PN junctions,of which the unilateral conductive and the out-of-order arrangement endowed itself insulating in all directions.The positive and negative charges in scale could not move,and the mobile number and transferring rate of them both dropped enormously,as a result,the oxidation rate of the matrix metal was cut down greatly.So the composite scale presented excellent oxidation resistance.

  17. Chemical-looping gasification of biomass in a 10k Wth interconnected fluidized bed reactor using Fe2 O3/Al2 O3 oxygen carrier

    Institute of Scientific and Technical Information of China (English)

    HUSEYIN Sozen; WEI Guo-qiang; LI Hai-bin; HE Fang; HUANG Zhen

    2014-01-01

    The aim of this research is to design and operate a 10 kW hot chemical-looping gasification ( CLG) unit using Fe2 O3/Al2 O3 as an oxygen carrier and saw dust as a fuel. The effect of the operation temperature on gas composition in the air reactor and the fuel reactor, and the carbon conversion of biomass to CO2 and CO in the fuel reactor have been experimentally studied. A total 60 h run has been obtained with the same batch of oxygen carrier of iron oxide supported with alumina. The results show that CO and H2 concentrations are increased with increasing temperature in the fuel reactor. It is also found that with increasing fuel reactor temperature, both the amount of residual char in the fuel reactor and CO2 concentration of the exit gas from the air reactor are degreased. Carbon conversion rate and gasification efficiency are increased by increasing temperature and H2 production at 870 ℃reaches the highest rate. Scanning electron microscopy (SEM), X-ray diffraction (XRD) and BET-surface area tests have been used to characterize fresh and reacted oxygen carrier particles. The results display that the oxygen carrier activity is not declined and the specific surface area of the oxygen carrier particles is not decreased significantly.

  18. Electrical conductivity of Na3AlF6-AlF3-Al2O3-CaF2-LiF(NaCl) system electrolyte

    Institute of Scientific and Technical Information of China (English)

    KAN Hong-min; WANG Zhao-wen; BAN Yun-gang; SHI Zhong-ning; QIU Zhu-xian

    2007-01-01

    A PGSTAT 30 and a BOOSTER 20A were used to measure cell impedance. Electrical conductivity was gained by the Continuously Varying Cell Constant Technique. Electrical conductivity of KCl was measured for comparison. The results prove that the method is reliable and accurate. The electrical conductivity of Na3AlF6-AlF3-Al2O3-CaF2-LiF(NaCl) system was studied by this method. Activation energy of conductance was obtained based on the experiment results. The experiments show that electrical conductivity is increased greatly with NaCl and LiF added. Increasing 1%LiF(mass fraction) results in corresponding increase of 0.0276 S/cm for superheat condition of 15 ℃. For NaCl, it is 0.024 S/cm. Electrical conductivity is increased by 0.003 S/cm with 1℃ temperature increase. The electrical conductivity is lower than that predicted by the WANG Model and higher than that predicted by the Choudhary Model.

  19. A comparison of the structural changes and optical properties of LiNbO3, Al2O3 and ZnO after Er+ ion implantation

    Science.gov (United States)

    Mackova, A.; Malinsky, P.; Pupikova, H.; Nekvindova, P.; Cajzl, J.; Svecova, B.; Oswald, J.; Wilhelm, R. A.; Kolitsch, A.

    2014-07-01

    This paper reports on the structural as well as compositional changes of LiNbO3, Al2O3 and ZnO crystals, implanted with Er+ ions at 190 keV a with fluence of 1.0 × 1016 cm-2 into the crystallographic cuts. Post-implantation annealing at 1000 °C in oxygen atmosphere was also done. The chemical compositions and erbium concentration-depth profiles of implanted layers were studied by Rutherford Backscattering Spectrometry (RBS) and compared to SRIM simulations. The same value of the maximum erbium concentration (up to 2 at.%) was observed at a depth of about 40 nm for all crystals. The structural properties of the prepared layers were characterised by RBS/channelling. The relative numbers of disordered atoms in the prepared implanted layers were compared with each other and discussed for various crystals. It has been found that erbium is located in LiNbO3 and in Al2O3 preferably in interstitial positions, unlike ZnO, where the largest amount of erbium (about 83%) is placed in substitutional positions after the implantation. The erbium position in the host matrix was substantially influenced by the annealing procedure. In ZnO, after the annealing, the erbium amount in substitutional positions significantly decreased; in LiNbO3 and Al2O3 the increase of erbium in substitutional positions was observed simultaneously with the improvement of the quality of the reconstructed host matrix. Since we are interested in the relationship between structural changes and optical properties, the erbium luminescence properties were measured in the region of wavelength 1440-1650 nm for all crystals. After ion implantation LiNbO3 samples had zero luminescence intensity, while ZnO and Al2O3 samples had one significant luminescence band at 1537 and 1530 nm, respectively. The annealing improved the luminescent properties significantly in all investigated crystalline materials.

  20. Investigation of process variables and intensification effects of ultrasound applied in oxidative desulfurization of model diesel over MoO3/Al2O3 catalyst.

    Science.gov (United States)

    Akbari, Azam; Omidkhah, Mohammadreza; Darian, Jafar Towfighi

    2014-03-01

    A new heterogeneous sonocatalytic system consisting of a MoO3/Al2O3 catalyst and H2O2 combined with ultrasonication was studied to improve and accelerate the oxidation of model sulfur compounds of diesel, resulting in a significant enhancement in the process efficiency. The influence of ultrasound on properties, activity and stability of the catalyst was studied in detail by means of GC-FID, PSD, SEM and BET techniques. Above 98% conversion of DBT in model diesel containing 1000 μg/g sulfur was obtained by new ultrasound-assisted desulfurization at H2O2/sulfur molar ratio of 3, temperature of 318 K and catalyst dosage of 30 g/L after 30 min reaction, contrary to the 55% conversion obtained during the silent process. This improvement was considerably affected by operation parameters and catalyst properties. The effects of main process variables were investigated using response surface methodology in silent process compared to ultrasonication. Ultrasound provided a good dispersion of catalyst and oxidant by breakage of hydrogen bonding and deagglomeration of them in the oil phase. Deposition of impurities on the catalyst surface caused a quick deactivation in silent experiments resulting only 5% of DBT oxidation after 6 cycles of silent reaction by recycled catalyst. Above 95% of DBT was oxidized after 6 ultrasound-assisted cycles showing a great improvement in stability by cleaning the surface during ultrasonication. A considerable particle size reduction was also observed after 3 h sonication that could provide more dispersion of catalyst in model fuel.

  1. Successful Nd3+ Doping of Li2O-B2O3-Al2O3 Vitreous System: Optical Characterization and Judd-Ofelt Spectroscopic Calculations

    Science.gov (United States)

    Silva, V. A.; Morais, P. C.; Morais, R. F.; Dantas, N. O.

    2016-12-01

    This study reports on the synthesis and the physical characterization of a ternary boron-rich (B-rich) lithium-boron-aluminum (LBA: Li2O-B2O3-Al2O3) vitreous system successfully doped with increasing Nd2O3 content ( xNd2O3:LBA) in the range 0 ≤ x ≤ 5 wt %. The as-produced samples were investigated using optical absorption, photoluminescence emission, Raman spectroscopy, and differential thermal analysis. The Judd-Ofelt (JO) theory was used to assess the intensity parameters ( Ω λ ), transition probabilities ( A( J, J')), branch ratios ( β), emission cross-sections ( σ), quantum efficiencies ( Y), experimental ( τ exp ) and calculated ( τ rad ) radiative lifetimes, and the spectroscopic quality values ( χ = Ω 4/ Ω 6) as a function of the nominal Nd2O3 doping content. Over the range of our investigation (0 ≤ x ≤ 5 wt %), we found that the Ω 2 and Ω 6JO parameters monotonically increased from 0.17 to 1.26 × 10-20 and from 1.19 to 1.84 × 10-20, respectively. In contrast, over the same range of nominal Nd2O3 doping content we found that the Ω 4 JO parameter decreased monotonically from 4.12 to 2.05 × 1 0-20. Although the τ exp values increased at the low end of nominal Nd2O3 content (up to 2.5 wt %), nonradiative energy transfer mechanisms (e.g., energy migration, cross-relaxation, and losses from networked phonons and O-H vibrational modes) governed the process at the high end of the nominal Nd2O3 content. A competition mechanism was proposed to explain the observed behavior in the 4F3/2 ⟶ 4IJ'transition lifetime for hosted Nd3+ ions.

  2. Joining of Silicon Nitride Using Y2O3-Al2O3-SiO2 Mixtures%用Y2O3-Al2O3-SiO2钎料进行Si3N4的连接

    Institute of Scientific and Technical Information of China (English)

    周飞; 陈铮; 李志章; 罗启富

    1999-01-01

    本文用二种Y2O3-Al2O3-SiO2(YAS)钎料进行Si3N4/Si3N4的连接研究.在20kPaN2,1450℃~1650℃保温15min的实验条件下,Si3N4/Si3N4的接头强度随连接温度的增加先增后降.微观分析表明:接头强度与YAS/Si3N4的界面扩散反应和接头残留玻璃相的厚度有关.

  3. ZnFe2O4基材料在NaF-AlF3-Al2O3熔盐中的腐蚀%CORROSION OF ZINC FERRITE IN NaF-AlF3-Al2O3 MOLTEN SALTS

    Institute of Scientific and Technical Information of China (English)

    于先进; 邱竹贤; 金松哲

    2000-01-01

    采用锌铁尖晶石材料作为铝电解惰性阳极,考察了这种阳极在 熔盐中的腐蚀 行为,阳极电流密度为0~2.5A/cm2.实验结果表明,锌铁尖晶石材料在阳极极化条件下的NaF-AlF3-Al2O3熔盐中具有很好的耐腐蚀性能.在低电流密度下,阳极材料的腐蚀速度随电流密度的增大而增大,最高的腐蚀速度出现于0.5~0.75A/cm2.此后,腐蚀速度随电流密度的增大而降低.实验证明,高阳极电流密度(>1.5A/cm2)、熔盐电解质中保持高Al2O3含量和低NaF/AlF3摩尔比,对降低阳极材料的腐蚀速度有利,这也将是惰性阳极应用的重要条件.%Zinc ferrite was used as inert anode materials for aluminum electrolysis. The corrosion behaviorof zinc fetrite as investigated under the anodic current density of 0-2.5A/cm2. Experinental results provethat zinc ferite materials is very corrosion resistant to molten NaF-AlF3-Al2O3 under the condition ofanodic polarization. The biggest corrosion rate appears in the range of 0.5 ~0.75A/cn2. The corrosionrate will get down after that peak value. High anodic current density (> 1.5 A/cm2 ), high aluminaconcentration and low mole ratio of NaF/AlF3 in the molten salts would be the most important conditionsfor using inert anode.

  4. Vapor Phase Beckmann Rearrangement of CyclohexanoneOxime over B2O3/Al2O3-TiO2 Catalysts%环己酮肟在B2O3/Al2O3-TiO2催化剂上的气相Beckmann重排反应

    Institute of Scientific and Technical Information of China (English)

    张晟; 毛东森; 卢冠忠; 陈庆龄

    2001-01-01

    制备了B2O3/Al2O3-TiO2复合载体催化剂,并考察了其对环己酮肟气相Beckmann重排制己内酰胺反应的催化性能. 结果表明,载体中TiO2的含量、B2O3的负载量、载体的预处理温度及催化剂的焙烧温度等均对催化剂的性能产生明显的影响. 当载体中TiO2含量为60%,B2O3负载量为20%,催化剂经350 ℃焙烧时,环己酮肟的气相Beckmann重排反应的转化率和选择性很高. 用BET,NH3-TPD,XRD和IR等方法对催化剂的织构、表面酸性和晶相等进行了表征,并与催化剂的活性进行了关联,表明催化剂表面中等强度的酸中心浓度与催化剂的选择性具有对应关系.

  5. B2O3/Al2O3 as a new, highly efficient and reusable heterogeneous catalyst for the selective synthesis of β-enamino ketones and esters under solvent-free conditions

    OpenAIRE

    Chen,Jiu-Xi; Zhang,Chang-Fu; Gao,Wen-Xia; Jin,Hui-Le; Ding,Jin-Chang; Wu,Hua-Yue

    2010-01-01

    Boron oxide adsorbed on alumina (B2O3/Al2O3 ) has been found to be a new and highly efficient heterogeneous catalyst for the synthesis of β-enamino ketones and esters by the enamination of various primary and secondary amines with β-dicarbonyl compounds under solvent-free conditions. The important features of this methodology are broad substrate scope, high yield, no requirement of metal catalysts, high regio- and chemoselectivity and environmental friendliness. In addition, the cat...

  6. B2O3/Al2O3 as a new, highly efficient and reusable heterogeneous catalyst for the selective synthesis of β-enamino ketones and esters under solvent-free conditions

    OpenAIRE

    Chen,Jiu-Xi; Zhang,Chang-Fu; Gao,Wen-Xia; Jin,Hui-Le; Ding,Jin-Chang; Wu,Hua-Yue

    2010-01-01

    Boron oxide adsorbed on alumina (B2O3/Al2O3 ) has been found to be a new and highly efficient heterogeneous catalyst for the synthesis of β-enamino ketones and esters by the enamination of various primary and secondary amines with β-dicarbonyl compounds under solvent-free conditions. The important features of this methodology are broad substrate scope, high yield, no requirement of metal catalysts, high regio- and chemoselectivity and environmental friendliness. In addition, the cat...

  7. Ag对Pd/CeO2-ZrO2-La2O3-Al2O3催化氧化甲醇性能的影响%Effects of Ag on Performance of Methanol Oxidation over Pd/CeO2-ZrO2-La2O3-Al2O3

    Institute of Scientific and Technical Information of China (English)

    张雪乔; 王世丹; 信欣; 刘盛余; 陈耀强; 赵明

    2012-01-01

    采用等体积共浸渍法制备了一系列Pd-Ag/CeO2-ZrO2-La2O3-Al2O3催化剂.运用N2吸附-脱附,X射线衍射(XRD),H2程序升温还原(H2-TPR),紫外-可见漫反射光谱(UV-Vis DRS),X射线光电子能谱(XPS)对催化剂进行表征,并考察其对甲醇的催化氧化性能.活性测试结果表明,Ag的添加可显著改善Pd催化剂对甲醇的催化氧化活性,T50、T90以及△T分别为125℃,150℃和25℃,具有较好的应用前景.H2-TPR表明,引入Ag可明显改善催化剂的还原性能,使表面易还原氧物种量增多,还原速率加快;UV-Vis DRS及XPS表明,Pd、Ag金属之间以及金属与载体之间存在电子效应,这种效应促使金属与载体界面产生大量具有活性的氧物种,不仅提高了催化剂的低温活性,还提高了催化剂的氧化速率.%Pd-Ag/CeO2-ZrO2-La2O3-Al2O3 catalysts were prepared by the co-impregnation method. Low temperature nitrogen adsorption-desorption, X-ray diffraction (XRD), H2-temperature-programmed reduction (H2-TPR), Ultra violet-visble difuse reflectance spectroscopy (UV-Vis DRS) and X-ray photoelectron spectroscopy (XPS) were carried out. The catalytic activities of these catalysts for the oxidation of methanol were investigated. The results of catalytic activity indicate that the presence of Ag significantly improves catalytic performance for methanol oxidation. The T50, T90 and △T are 125℃, 150 ℃ and 25℃, respectively. H2-TPR results suggest that the addition of Ag increases the amount of active oxygen and promotes the reductive ability. The UV-Vis DRS and XPS results indicate that electron effects between Pd and Ag, Pd-Ag and support are favorable for producing larger activated oxygen via easy migration on the Pd-Ag/CeO2 interface, thus promoting both the catalytic activity at low temperature and the speed of catalytic oxidation.

  8. K2CO3/Al2O3催化餐饮废油酯交换制备生物柴油的动力学%Kinetics of solid base K2CO3/Al2O3 catalyzed transesterification of waste cooking oil for biodiesel production

    Institute of Scientific and Technical Information of China (English)

    胡秀英; 马迪; 杨廷海; 邓育苟

    2014-01-01

    以餐饮废油和甲醇为原料,固体碱K2CO3/Al2O3为催化剂进行酯交换反应.考察了反应温度和反应时间对酯交换反应的影响.实验结果表明,酯交换反应速率随反应温度的升高而加快,最佳反应温度为65℃,反应时间为2h,废油转化率最高可达95.7%.通过改变反应温度得到了酯交换反应动力学数据,即酯交换反应级数为1.94级,平均活化能为36.49 kJ/mol,指前因子为2.17×105L/(mol·min),建立了酯交换反应动力学方程,并对动力学方程进行了验证.验证结果表明,废油转化率的计算值与实验值的相对误差均小于4%,说明所建立的反应速率方程在实验条件范围内能较好地描述该酯交换反应.该研究为固体碱催化餐饮废油与甲醇酯交换反应的动力学提供了理论基础.

  9. Reduction of NO by CO using Pd-CeTb and Pd-CeZr catalysts supported on SiO2 and La2O3-Al2O3

    Institute of Scientific and Technical Information of China (English)

    Victor Ferrer; Dora Finol; Roger Solano; Alexander Moronta; Miguel Ramos

    2015-01-01

    The catalytic activity of Pd catalysts supported on Ce0.73Tb0.27Ox/SiO2,Ce0.6Zr0.4Ox/SiO2,Ce0.73Tb0.27Ox/La2O3-Al2O3 and Ce0.6Zr0.4Ox/La2O3-Al2O3 was studied using the reduction of NO by CO.The catalysts were characterized by X-ray fluorescence,surface area,X-ray diffraction,temperature-programmed reduction,CO chemisorption and oxygen storage capacity.Temperature-programmed reduction results indicated that Tb or Zr incorporation improves the reducibility and oxygen storage capacity.CO chemisorption data suggested the presence of large PdO particles due to the low CO/Pd ratio.No significant differences were obtained in light offtemperatures (TLight off) for all Pd catalysts and the most active was 1.5%Pd/Ce0.6Zr0.4Ox/SiO2.

  10. Photo-degradation of basic green 1 and basic red 46 dyes in their binary solution by La2O3-Al2O3nanocomposite using first-order derivative spectra and experimental design methodology.

    Science.gov (United States)

    Fahimirad, Bahareh; Asghari, Alireza; Rajabi, Maryam

    2017-02-10

    In this work, the lanthanum oxide-aluminum oxide (La2O3-Al2O3) nanocomposite is introduced as an efficient photocatalyst for the photo-degradation of the dyes basic green 1 (BG1) and basic red 46 (BR46) in their binary aqueous solution under the UV light irradiation. The properties of this catalyst are determined by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), Brunauer-Emmett-Teller (BET), and UV-visible spectrophotometry. The first-order derivative spectra are used for the simultaneous analysis of the dyes in their binary solution. The screening investigations indicate that five parameters including the catalyst dosage, concentration of the dyes, irradiation time, and solution pH have significant effects on the photo-degradation of the dyes. The effects of these variables together with their interactions in the photo-degradation of the dyes are studied using the Box-Behnken design (BBD). Under the optimum experimental conditions, obtained via the desirability function, the photo-catalytic activities of La2O3-Al2O3 and pure Al2O3 are also investigated. The results obtained show an enhancement in the photo-catalytic activity when La2O3 nanoparticles are loaded on the surface of Al2O3 nanoparticles.

  11. Bi2O3/Al2O3纳米复合物的声化学合成及其对大肠杆菌和金黄色葡萄球菌的抑制作用%Sonochemical Synthesis and Application of Bi2O3-Al2O3 Nanocomposites and Their Bateria-Inhibition Against E.coil and Staphylococcus aureaus

    Institute of Scientific and Technical Information of China (English)

    武志富; 沈玉华; 谢安建; 黄方志

    2011-01-01

    以偏铝酸钠和硝酸铋为原料在超声辐照下反应,一步法合成了Bi2O3-Al2O3纳米复合物.用电感耦合等离子体发射光谱(ICP),元素分析和热重分析确定了产物的组成,并通过傅立叶变换红外光谱(FTIR)、粉末X射线衍射(XRD)和透射电子显微镜(TEM)等测试手段对所得产物进行了表征.结果表明,产物为近似球状晶体,在超声40 min条件下粒径平均为24nm.探讨了pH值和干燥温度以及超声时间对所得产物成分和粒径的影响.这类物质原本是一种治疗消化性溃疡和神经性消化不良的药物.实验发现,其中两种复合物对大肠杆菌和金黄色葡萄球菌具有明显的抑制作用.%Bi2O3-Al2O3 nanocomposite materials were synthesized via a mild sonochemical route from aqueous solution of NaAlO2 and Bi(NO3)3, FTIR spectra, TEM images, XRD patterns, ICP analysis, PCS and element analysis were used to characterize the obtained particles, and also measured the granularity of obtained particles with different ultrasonic time. The result showed that Bi2O3-Al2O3 nanocomposite synthesized in the alkaline solution is spherical crystal with average diameter of 24 nm, In addition, the influence of pH value, desiccation temperature and ultrasonic time on the formation of the products were discussed. Bateria-inhibition assays showed that the nanocomposite materials have potent against E. coil and Staphylococcus aureaus.

  12. V2O5-TiO2-AlF3/Al2O3催化臭氧化2,4-滴丙酸的氧化效能%Oxidative efficiency of ozonation of 2-(2,4-dichlorophenoxy)propionic acid in the presence of V2O5-TiO2-AlF3/Al2O3

    Institute of Scientific and Technical Information of China (English)

    蓝小飞; 曹利刚; 恽正兴; 童少平

    2013-01-01

    A novel tri-components catalyst characterized as V2O5-TiO2-AlF3/Al2O3 by XRD was prepared via incipient wetness impregnation to promote ozonation efficiency.The activity of the catalyst in ozonation was evaluated by degradation of 2-(2,4-dichlorophenoxy) propionic acid (2,4-DP).The results showed that the catalyst could greatly improve the efficiency of ozonation of 2,4-DP.The test of tert-butyl alcohol addition indicated that the catalytic ozonation of 2,4-DP might follow a hydroxyl radical-type mechanism.The Rct value of the catalytic ozonation calculated by the relative method was larger than that of ozonation alone.The repeated test indicated that the catalyst remained relatively stable in the catalytic ozonation of 2,4-DP.The above results are of great significance for extending application of catalytic ozonation of advanced oxidation process in wastewater treatment.%为了提高有机物的臭氧化降解效率,工作中利用浸渍法制备了一种新型的三组分催化剂(记为V2O5-TiO2-AlF3/Al2O3).催化臭氧化降解2,4-滴丙酸的实验结果表明,该催化剂能有效提高臭氧化的效率,体系可能遵循羟基自由基的作用机理.利用相对法计算结果表明,与单独臭氧化相比,V2O5-TiO2-AlF3/Al2O3催化臭氧化体系具有更大的Rct值.重复实验结果表明,该催化剂具有相对较好的稳定性.以上研究结果对推广催化臭氧化技术在实际废水处理中的应用具有重要的实际意义.

  13. First Single-Crystal Mullite Fibers

    Science.gov (United States)

    1997-01-01

    Ceramic-matrix composites strengthened by suitable fiber additions are being developed for high-temperature use, particularly for aerospace applications. New oxide-based fibers, such as mullite, are particularly desirable because of their resistance to high-temperature oxidative environments. Mullite is a candidate material in both fiber and matrix form. The primary objective of this work was to determine the growth characteristics of single-crystal mullite fibers produced by the laser-heated floating zone method. Directionally solidified fibers with nominal mullite compositions of 3Al2O3 2SiO2 were grown by the laser-heated floating zone method at the NASA Lewis Research Center. SEM analysis revealed that the single-crystal fibers grown in this study were strongly faceted and that the facets act as critical flaws, limiting fiber strength. The average fiber tensile strength is 1.15 GPa at room temperature. The mullite fibers exhibit superior strength retention (80 percent of their room temperature tensile strength at 1450 C). Examined by transmission electron microscopy, these mullite single crystals are free of dislocations, low-angle boundaries, and voids. In addition, they show a high degree of oxygen vacancy ordering. High-resolution digital images from an optical microscope furnish evidence of the formation of a liquid-liquid miscibility gap during crystal growth. These images represent the first experimental evidence of liquid immiscibility for these compositions and temperatures. Continuing investigation with controlled seeding of mullite single crystals is planned.

  14. Plasma Spray Forming

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    In the course of plasma spray, the plasma jet is comprehensively functioned by such effects as thermal pinch, magnetic pinch and mechanical compression and the flow is jetting at a high speed, the energy is concentrated and its center temperature is so high as to reach upwards of 15 000 ℃ which is capable of melting various kinds of materials inclusive of ceramic, it has a broad applied prospects in the fields of automobile, electronics, telecommunications, medical treatment, air navigation & space navigati...

  15. Vacuum plasma spray coating

    Science.gov (United States)

    Holmes, Richard R.; Mckechnie, Timothy N.

    1989-01-01

    Currently, protective plasma spray coatings are applied to space shuttle main engine turbine blades of high-performance nickel alloys by an air plasma spray process. Originally, a ceramic coating of yttria-stabilized zirconia (ZrO2.12Y2O3) was applied for thermal protection, but was removed because of severe spalling. In vacuum plasma spray coating, plasma coatings of nickel-chromium-aluminum-yttrium (NiCrAlY) are applied in a reduced atmosphere of argon/helium. These enhanced coatings showed no spalling after 40 MSFC burner rig thermal shock cycles between 927 C (1700 F) and -253 C (-423 F), while current coatings spalled during 5 to 25 test cycles. Subsequently, a process was developed for applying a durable thermal barrier coating of ZrO2.8Y2O3 to the turbine blades of first-stage high-pressure fuel turbopumps utilizing the enhanced NiCrAlY bond-coating process. NiCrAlY bond coating is applied first, with ZrO2.8Y2O3 added sequentially in increasing amounts until a thermal barrier coating is obtained. The enchanced thermal barrier coating has successfully passed 40 burner rig thermal shock cycles.

  16. Elastic Modulus Evolution and Behavior of Si/Mullite/BSAS-Based Environmental Barrier Coatings Exposed to High Temperature in Water Vapor Environment

    Science.gov (United States)

    Cojocaru, C. V.; Kruger, S. E.; Moreau, C.; Lima, R. S.

    2011-01-01

    Si-based ceramics (e.g., SiC and Si3N4) are known as promising high-temperature structural materials in various components where metals/alloys reached their ultimate performances (e.g., advanced gas turbine engines and structural components of future hypersonic vehicles). To alleviate the surface recession that Si-based ceramics undergo in a high-temperature environmental attack (e.g., H2O vapor), appropriate refractory oxides are engineered to serve as environmental barrier coatings (EBCs). The current state-of-the-art EBCs multilayer system comprises a silicon (Si) bond coat, mullite (3Al2O3·2SiO2) interlayer and (1 - x)BaO· xSrO·Al2O3·2SiO2, 0 ≤ x ≤ 1 (BSAS) top coat. In this article, the role of high-temperature exposure (1300 °C) performed in H2O vapor environment (for time intervals up to 500 h) on the elastic moduli of air plasma sprayed Si/mullite/BSAS layers deposited on SiC substrates was investigated via depth-sensing indentation. Laser-ultrasonics was employed to evaluate the E values of as-sprayed BSAS coatings as an attempt to validate the indentation results. Fully crystalline, crack-free, and near-crack-free as-sprayed EBCs were engineered under controlled deposition conditions. The absence of phase transformation and stability of the low elastic modulus values (e.g., ~60-70 GPa) retained by the BSAS top layers after harsh environmental exposure provides a plausible explanation for the almost crack-free coatings observed. The relationships between the measured elastic moduli of the EBCs and their microstructural behavior during the high-temperature exposure are discussed.

  17. Análisis de la adhesión de recubrimientos del sistema Y2O3-Al2O3-SiO2 sobre sustratos de interés para la industria aeroespacial

    Directory of Open Access Journals (Sweden)

    Cinta Marraco-Borderas

    2016-07-01

    Full Text Available En la industria aeroespacial se necesitan materiales ligeros que tengan unas altas prestaciones mecánicas combinadas con una baja densidad. El carburo de silicio, el carbono reforzado con fibra de carbono y el carburo de silicio reforzado con fibra de carbono son materiales que cumplen con estos requisitos, pero a altas temperaturas presentan problemas de oxidación. Una de las formas más efectivas de prevenir este fenómeno es la utilización de recubrimientos cerámicos, cuya correcta adhesión sobre los distintos sustratos es fundamental para garantizar su funcionamiento. En el caso del presente trabajo, se analiza la adhesión de recubrimientos vítreos del sistema Y2O3-Al2O3-SiO2 obtenidos mediante proyección térmica por llama oxiacetilénica. Para ello, se realizan ensayos de rayado a carga creciente analizando el tipo y la carga de fallo y su relación con las propiedades elásticas y mecánicas de los recubrimientos. Los resultados indican que la adhesión sobre los sustratos carburo de silicio y carburo de silicio reforzado con fibra de carbono es buena, mientras que el carbono reforzado con fibra de carbono no es un material adecuado para recubrir.

  18. Evaluation on Properties of CaO-BaO-B2O3-Al2O3-SiO2 Glass-Ceramic Sealants for Intermediate Temperature Solid Oxide Fuel Cells

    Institute of Scientific and Technical Information of China (English)

    Fatemeh Heydari; Amir Maghsoudipour; Zohreh Hamnabard; Sajad Farhangdoust

    2013-01-01

    To develop suitable sealants for intermediate temperature solid oxide fuel cells (IT-SOFC),glass-ceramics based on the CaO-BaO-B2O3-Al2O3-SiO2 system were studied.Coefficient of thermal expansion (CTE),glass transition temperature (Tg) and dilatometric softening point temperature (Td) of specimens were determined by means of dilatometer analysis and crystallization temperature was measured by differential thermal analysis (DTA).Also,crystallization behavior during prolonged heat-treatment and microstructure properties were studied by means of X-ray diffraction (XRD) and scanning electron microscopy (SEM),respectively.Electrical properties were measured at different temperatures,and the results showed a high resistance (>104 Ω) at the SOFC operation temperature (600-800 ℃).Moreover,mechanical properties of heat-treated specimens (1,10,30,50 h) were measured.Microstructure investigation revealed a well-adhered bonding between the sealant glass-ceramic electrolyte and glass.

  19. Faraday rotation and photoluminescence in heavily Tb3+-doped GeO2-B2O3-Al2O3-Ga2O3 glasses for fiber-integrated magneto-optics

    Science.gov (United States)

    Gao, Guojun; Winterstein-Beckmann, Anja; Surzhenko, Oleksii; Dubs, Carsten; Dellith, Jan; Schmidt, Markus A.; Wondraczek, Lothar

    2015-01-01

    We report on the magneto-optical (MO) properties of heavily Tb3+-doped GeO2-B2O3-Al2O3-Ga2O3 glasses towards fiber-integrated paramagnetic MO devices. For a Tb3+ ion concentration of up to 9.7 × 1021 cm−3, the reported glass exhibits an absolute negative Faraday rotation of ~120 rad/T/m at 632.8 nm. The optimum spectral ratio between Verdet constant and light transmittance over the spectral window of 400–1500 nm is found for a Tb3+ concentration of ~6.5 × 1021 cm−3. For this glass, the crystallization stability, expressed as the difference between glass transition temperature and onset temperature of melt crystallization exceeds 100 K, which is a prerequisite for fiber drawing. In addition, a high activation energy of crystallization is achieved at this composition. Optical absorption occurs in the NUV and blue spectral region, accompanied by Tb3+ photoluminescence. In the heavily doped materials, a UV/blue-to-green photo-conversion gain of ~43% is achieved. The lifetime of photoluminescence is ~2.2 ms at a stimulated emission cross-section σem of ~1.1 × 10−21 cm2 for ~ 5.0 × 1021 cm−3 Tb3+. This results in an optical gain parameter σem*τ of ~2.5 × 10−24 cm2s, what could be of interest for implementation of a Tb3+ fiber laser. PMID:25754819

  20. Faraday rotation and photoluminescence in heavily Tb(3+)-doped GeO2-B2O3-Al2O3-Ga2O3 glasses for fiber-integrated magneto-optics.

    Science.gov (United States)

    Gao, Guojun; Winterstein-Beckmann, Anja; Surzhenko, Oleksii; Dubs, Carsten; Dellith, Jan; Schmidt, Markus A; Wondraczek, Lothar

    2015-03-10

    We report on the magneto-optical (MO) properties of heavily Tb(3+)-doped GeO2-B2O3-Al2O3-Ga2O3 glasses towards fiber-integrated paramagnetic MO devices. For a Tb(3+) ion concentration of up to 9.7 × 10(21) cm(-3), the reported glass exhibits an absolute negative Faraday rotation of ~120 rad/T/m at 632.8 nm. The optimum spectral ratio between Verdet constant and light transmittance over the spectral window of 400-1500 nm is found for a Tb(3+) concentration of ~6.5 × 10(21) cm(-3). For this glass, the crystallization stability, expressed as the difference between glass transition temperature and onset temperature of melt crystallization exceeds 100 K, which is a prerequisite for fiber drawing. In addition, a high activation energy of crystallization is achieved at this composition. Optical absorption occurs in the NUV and blue spectral region, accompanied by Tb(3+) photoluminescence. In the heavily doped materials, a UV/blue-to-green photo-conversion gain of ~43% is achieved. The lifetime of photoluminescence is ~2.2 ms at a stimulated emission cross-section σem of ~1.1 × 10(-21) cm(2) for ~ 5.0 × 10(21) cm(-3) Tb(3+). This results in an optical gain parameter σem*τ of ~2.5 × 10(-24) cm(2)s, what could be of interest for implementation of a Tb(3+) fiber laser.

  1. Liquid phase sintering of silicon carbide with AlN/Y2O3, Al2O3/Y2O3 and SiO2/Y2O3 additions

    Directory of Open Access Journals (Sweden)

    Kurt Strecker

    1999-10-01

    Full Text Available In this work, the influence of the additive system on the liquid phase sintering of silicon carbide has been investigated. The additives employed were mixtures of AlN/Y2O3, Al2O3/Y2O3 and SiO2/Y2O3. The total additive content was fixed at 20 vol.-%, maintaining the Y2O3 content in each additive system at 35 vol.-%. Cold isostatically pressed samples were sintered at 1900, 2000 and 2100 °C under Ar atmosphere during 30 min. The most promising results have been obtained by samples with AlN/Y2O3 additions sintered at 2000 °C, exhibiting the smallest weight loss of about 6% and the highest flexural strengths of about 433 MPa. Samples with Al2O3/Y2O3 and SiO2/Y2O3 additions exhibited high weight loss, because of reactions of Al2O3 and SiO2 with the SiC matrix, forming gaseous species such as Al2O, SiO and CO, resulting in depletion of the liquid phase, and, consequently, in inferior final densities and mechanical properties. Concerning the SiO2/Y2O3 additive system, the reactions seem to be completed already at temperatures below 1900 °C, turning this additive mixture unsuitable. The microstructural analysis indicated only the presence of the b-SiC phase for all samples; no phase transformation of the b-SiC into a-SiC has been observed.

  2. Controlled reduction of LaFe xMn yMo zO3/Al2O3 composites to produce highly dispersed and stable Fe0 catalysts: a Mössbauer investigation

    Directory of Open Access Journals (Sweden)

    Juliana Cristina Tristão

    2008-06-01

    Full Text Available In this work, controlled reduction of perovskites supported on Al2O3 was used to prepare thermally stable nanodispersed iron catalysts based on Fe0/La2O3/Al2O3. The perovskites composites LaFe0.90Mn0.08Mo0.02O3(25, 33 and 50 wt (% /Al2O3 and LaFe0.90Mn0.1O3(25 wt (% /Al2O3 were prepared and characterized by XRD, BET, TPR, SEM and Mössbauer spectroscopy. XRD for unsupported perovskite showed the formation of a single phase perovskite structure. The Mössbauer spectra of the perovskites were fitted with hyperfine field distribution model for the perovskite. Supported perovskites on Al2O3 showed a decrease of the hyperfine field in respect to unsupported perovskite, due to decrease of particle size and dispersion of the Fe3+ specimens on the support. Also showed broaden lines and relaxation effects due to the small particle size. To produce the Fe0 catalyst, the composite perovskite(25%/Al2O3 was reduced with H2 at 900, 1000 and 1100 °C for 1 hour. XRD data indicated the formation of Fe0 catalyst with particles sizes of ca. 35 nm. The Mössbauer spectrum showed the formation of metallic iron and doublets corresponding to species of octahedric Fe2+ and Fe3+ sites dispersed on Al2O3. These catalysts showed improved stability towards sintering even upon treatment at 1000 and 1100 °C under H2.

  3. Functionally graded mullite coatings for gas turbines

    Science.gov (United States)

    Kulkarni, Tushar

    The next generation of heat exchangers and gas turbines require high performance materials as they need to operate at higher temperatures for higher efficiency. SiC and Si3N4 are promising candidates as they have excellent high temperature properties. However, when used in complex combustion environments found in gas-turbine applications, these materials have two major concerns; namely hot-corrosion and recession. It is well established that environmental barrier coatings (EBC) can be utilized to overcome these limitations. Although chemical vapor deposited (CVD) mullite (3Al2O 3.2SiO2) coatings developed before this study have shown promise in protecting Si-based substrates, there is concern that the silica content within the mullite coating itself might be susceptible to hot-corrosion and recession during long term exposure to corrosive atmospheres containing Na/V salts and water vapor. There is thus strong motivation to substantially reduce or even virtually eliminate the silica component from the surfaces of mullite coatings that are in direct contact with atmospheres containing corrosive oxides and steam. In this study, CVD has been used to deposit mullite coatings with potential promise to protect Si-based ceramics for high temperature applications. The composition of these functionally graded mullite coatings was varied from silica-rich close to the coating/substrate (SiC) interface for coefficient of thermal expansion match to alumina-rich towards the outer surface of the coating. In the process, the highest alumina-rich mullite ever reported has been deposited. The phase transformation and hot-corrosion behavior of the coatings was also investigated in this work. The coatings show immense potential to protect Si-based ceramics. It is expected that these coatings will have very broad impact by enabling gas turbines to operate at higher temperatures leading to improved fuel efficiency and reduced emissions.

  4. Calculation and Verification for the Thermodynamic Data of 3CaO·3Al2O3·CaSO4%高温固硫矿物3CaO·3A12O3·CaSO4的热力学数据的计算与验证

    Institute of Scientific and Technical Information of China (English)

    王文龙; 陈晓冬; 陈莹; 董勇; 马春元

    2011-01-01

    Calcium sulfoaluminate, 3CaO·3Al2O3·CaSO4, has been widely recognized in the realms of high-temperature combustion and cement chemistry. However, the lack of relevant thermodynamic data limits the progress of its research and development. Through comparative calculations using several different approaches, we obtain the thermochemical properties of 3CaO·3Al2O3·CaSO4 in this work, such as its standard formation enthalpy, Gibbs free energy of formation, entropy, and molar heat capacity. With these fundamental data, thermodynamic calculations become possible for reactions involving this mineral. It is found that some reactions proposed in literature to generate this mineral may not proceed thermodynamically.

  5. Ultrasonic Plasma Spray--A New Plasma Spray Process

    Institute of Scientific and Technical Information of China (English)

    LU Zhi-qing; ZHANG Hua-tang; WEN Xiong-wei; LI Lu-ming

    2004-01-01

    The method of arc- ultrasonic is introduced into plasma spray process. The process of spray ZrO2-NiCoCr AlY thermal barrier coatings (TBCs) using air plasma spray (APS) process is studied. A exciting source which can be adjusted from audio frequency to several hundred thousand Hertz is designed successfully. The ultrasonic exciting source is coupled with conventional DC spraying power supply. A few ultrasonic frequencies are selected in the testing. Several parts of the coatings with the coupling arc- ultrasonic are compared with the coatings without it. The results show: with 50 kHz and 80 kHz ultrasound, the coating qualities are improved, whereas 30 kHz has an opposite effect.

  6. Sol-Gel Synthesis of Mullite Starting from Different Inorganic Precursors

    Directory of Open Access Journals (Sweden)

    Lucia Téllez Jurado

    2013-01-01

    Full Text Available Using silicotetraetilortosilicate (TEOS mixed with aluminum tri-sec-butoxide (TSBAI or aluminum cloaures mullite ceramics were created by the sol-gel method. The quantities used of each substance were those that led to obtain stoichiometric mullite (3Al2O3·2SiO2. The experimental methodology used for obtaining mullite consisted in: sol-gel synthesis of precursor materials, isothermal treatment of those materials, and characterization of resulting materials. In order to determine the advance of reactions during mullite formation, isothermal treatments between 300°C and 1600°C were performed, keeping the samples at each temperature during 4 h. From XRD results, it may be said that precursor powders originally amorphous start to crystallize in Al2O3 and SiO2 at 1200°C, and the mullite formation starts at 1200°C, with being completed at 1600°C. The use of TSBAI favors the formation of mullite crystals at lower temperature. From SEM observations a microstructure that presents primary mullite with randomly oriented grains of secondary mullite with acicular shapes and sizes that range between 1.25 and 1.50 μm long may be determined.

  7. Evaluation of Performance and Emission characteristics of Turbocharged Diesel Engine with Mullite as Thermal Barrier Coating

    OpenAIRE

    P. N. Shrirao; A. N. Pawar

    2011-01-01

    Tests were performed on a single cylinder, four stroke, direct injection, diesel engine whose piston crown, cylinder head and valves were coated with a 0.5 mm thickness of 3Al2O3 .2SiO2 (mullite) (Al2O3= 60%, SiO2= 40%) over a 150 μm thickness of NiCrAlY bond coat. Tests were carried out on standard engine (uncoated) and low heatrejection (LHR) engine with and without turbocharger. This paper is intended to emphasis on energy balance and emission characteristic for standard engine (uncoated) ...

  8. Estudo da viabilidade de obtenção de cerâmicas de SiC por infiltração espontânea de misturas eutéticas de Y2O3-AlN, Y2O3-Al2O3, R2O3-AlN Study of the viability to produce SiC ceramics by Y2O3-AlN, Y2O3-Al2O3, R2O3-AlN spontaneous infiltration

    Directory of Open Access Journals (Sweden)

    G. C. R. Garcia

    2008-06-01

    Full Text Available As cerâmicas de carbeto de silício, SiC, apresentam excelentes propriedades quando obtidas por infiltração de determinados líquidos. Na infiltração o tempo de contato entre o líquido e o SiC a temperaturas elevadas é muito curto, diminuindo a probabilidade de formação dos produtos gasosos que interferem negativamente na resistência da peça final, como ocorre na sinterização via fase líquida. O objetivo deste trabalho é mostrar uma correlação entre molhabilidade e capacidade de infiltração de alguns aditivos em compactos de SiC. Foram preparados compactos de SiC por prensagem isostática a frio e posterior pré-sinterização via fase sólida. Nesses compactos foram infiltradas misturas de Y2O3-AlN, Y2O3-Al2O3, R2O3-AlN, nas composições eutéticas, 10 ºC acima da temperatura de fusão das respectivas misturas por 4, 8 e 12 min. Após infiltração, as amostras foram analisadas quanto à densidade aparente e real, fases cristalinas, microestrutura e grau de infiltração, sendo que as amostras infiltradas com Y2O3-AlN apresentaram melhores resultados.Silicon carbide ceramics, SiC, obtained by liquid infiltration have shown excellent properties. In infiltration process the contact time of the liquid with SiC at elevated temperature is short, decreasing the probability to form gaseous products that contribute negatively in the final product properties. This phenomenon occurs during SiC liquid phase sintering. The purpose of the present study was to investigate the correlation between wettability and infiltration tendency of some additives in SiC compacts. SiC compacts were prepared by cold isostatic pressing followed by solid phase pre-sintering. Into the compacts were introduced Y2O3-AlN, Y2O3-Al2O3, R2O3-AlN liquids with eutectic compositions at a temperature 10 ºC higher than the melting point of each mixture for 4, 8 and 12 min. Before infiltration, the samples were analyzed by determining densities, crystalline phases

  9. Plasma spraying system with distributed controlling

    Institute of Scientific and Technical Information of China (English)

    李春旭; 陈克选; 张成

    2003-01-01

    A distributed control system is designed for plasma spraying equipment and the configurations of system software and hardware is discussed. Through founding an expert database, the spraying process parameters are worked out and the initialization and control of spraying process are realized. The plasma spraying system with this control configuration can simplify the spraying operation, improve automation level of spray process, and approach the experience criterion as soon as possible.

  10. Mullite preparation from natural raw materials; Preparacao de mulita a partir de materias-primas naturais

    Energy Technology Data Exchange (ETDEWEB)

    Sales, Lindemberg Felismino; Almeida Filho, Humberto Dias de; Goncalves, Joao de Freitas; Macedo, Daniel Araujo de [Universidade Federal da Paraiba (UFPB), Joao Pessoa, PB (Brazil). Departamento de Engenharia de Materiais

    2016-07-01

    The mullite (3Al2O3.2SiO2) has emerged as one of the most important refractory ceramics today. In this work, kaolin, and mixtures of coffee husk ash, a residue arising from the burning of coffee husks were studied in order to obtain the mullite ceramic base. Ceramic formulations with different maximum percentage (1%, 5% and 10%) of the residue were shaped by uniaxial pressing at 250 MPa and sintered between 1100 and 1400 ° C for 1 h. The technological properties were determined on the basis of residue content and sintering temperature. The phase transformations and microstructure were examined by XRD and SEM. The bulk density (MEA) samples containing 1% by mass of coffee residue, and sintered at 1350 ° C was 2.7 g / cm3. (author)

  11. Effect of the Fourth Element on Bonding of Si3N4 Ceramics with Y2O3-A l2O3-SiO2 Glass Solders%第四组元对Y2O3-Al2O3-SiO2钎料连接氮化硅陶瓷的影响

    Institute of Scientific and Technical Information of China (English)

    周飞

    2001-01-01

    在Y2O3-Al2O3-SiO2(YAS)钎料中添加TiO2(YT)和Si3N4(YN), 并进 行氮化硅陶瓷的连接。 用四点弯曲方法测定不同连接工艺下的连接强度, 并对连接界面进 行SEM, EPMA和XRD分析。 接头强度随着保温时间、 连接温度的增加, 而逐渐增加。 在 达到峰值后, 连接强度逐渐降低。 在YAS中添加TiO2, 可以形成Si3N4/Y-Sialon 玻璃+TiN/TiN/Y-Sialo玻璃的梯度层界面; 而在YAS钎料中添加Si3N4, 可以降低接 头界面的热应力, 改善接头强度。 微观分析表明: 接头强度的变化主要与界面反应有关 。%Bonding of Si3N4 ceramics was performed with Y2O3-Al2O3-SiO2(YAS )-X glass solders, which were mixed with TiO2 (YT) and Si3N4(YN) respe ctively. The effects of bonding conditions and interfacial reaction on the joint strength were studied. The joint strength of different bonding conditions was m easured by four-point bending tests. The interfacial microstructures were obser ved and analyzed by SEM, EPMA and XRD respectively. It is shown that with the in crease of bonding temperature and holding time, the joint strength increases rea ching a peak, and then decreases. When TiO2 is put into YAS solder, the bondi ng interface with Si3N4/Y-Sialon glass+TiN/TiN/Y-Sialo glass is formed. W hen YAS solder is mixed with Si3N4 powder, the interfacial thermal stress m ay be decreased, and the joint strength is enhanced. According to microanalyses , the bonding strength is related to interface reaction.

  12. Plasma-Spray Metal Coating On Foam

    Science.gov (United States)

    Cranston, J.

    1994-01-01

    Molds, forms, and other substrates made of foams coated with metals by plasma spraying. Foam might be ceramic, carbon, metallic, organic, or inorganic. After coat applied by plasma spraying, foam left intact or removed by acid leaching, conventional machining, water-jet cutting, or another suitable technique. Cores or vessels made of various foam materials plasma-coated with metals according to method useful as thermally insulating containers for foods, liquids, or gases, or as mandrels for making composite-material (matrix/fiber) parts, or making thermally insulating firewalls in automobiles.

  13. Laser treatment of plasma sprayed HA coatings

    NARCIS (Netherlands)

    Khor, KA; Vreeling, A; Dong, ZL; Cheang, P

    1999-01-01

    Laser treatment was conducted on plasma sprayed hydroxyapatite (HA) coatings using a Nd-YAG pulse laser. Various laser parameters were investigated. The results showed that the HA surface melted when an energy level of greater than or equal to 2 J and a spot size of 2 mm was employed during continuo

  14. Laser treatment of plasma sprayed HA coatings

    NARCIS (Netherlands)

    Khor, KA; Vreeling, A; Dong, ZL; Cheang, P

    1999-01-01

    Laser treatment was conducted on plasma sprayed hydroxyapatite (HA) coatings using a Nd-YAG pulse laser. Various laser parameters were investigated. The results showed that the HA surface melted when an energy level of greater than or equal to 2 J and a spot size of 2 mm was employed during continuo

  15. Surface silver-doping of biocompatible glasses to induce antibacterial properties. Part II: Plasma sprayed glass-coatings.

    Science.gov (United States)

    Miola, M; Ferraris, S; Di Nunzio, S; Robotti, P F; Bianchi, G; Fucale, G; Maina, G; Cannas, M; Gatti, S; Massé, A; Vitale Brovarone, C; Verné, E

    2009-03-01

    A 57% SiO(2), 3% Al(2)O(3), 34% CaO and 6% Na(2)O glass (SCNA) has been produced in form of powders and deposited by plasma spray on titanium alloy and stainless steel substrates. The obtained coatings have been subjected to a patented ion-exchange treatment to introduce silver ions in the surface inducing an antibacterial behavior. Silver surface-enriched samples have been characterized by means of X-ray diffraction, SEM observation, EDS analysis, in vitro bioactivity tests, leaching tests by GFAAS (graphite furnace atomic adsorption spectroscopy) analyses, cells adhesion and proliferation, and antibacterial tests using Staphylococcus Aureus strain. In vitro tests results showed that the modified samples acquired an antimicrobial action against tested bacteria maintaining unaffected the biocompatibility of the glass. Furthermore the ion-exchange treatment can be successfully applied to glass-coated samples without affecting the properties of the coatings; the simplicity and reproducibility of the method make it suitable for glass or glass-ceramic coatings of different composition in order to produce coated devices for bone healing and/or prostheses, able to reduce bacterial colonization and infections risks.

  16. Plasma Spray Forming of Nanostructured Composite Coatings

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The nanostructure composite coating is obtained via plasma spraying of Al2O3-13 wt pct TiO2 powder. Brittle and hard lamella results from melted nanostructured powder. Ductile nanostructured matrix forms from unmelted nanostructured particles. Through the adjustment of constituent and nanostructure, hardness/strength and toughness/ductility are balanced and overall properties of the structure composite are achieved.

  17. Comparative Study of Performance and Combustion Characteristics of Conventional and Low Heat Rejection (Mullite Coated) Diesel Engines

    Science.gov (United States)

    Patond, S. B.; Chaple, S. A.; Shrirao, P. N.; Shaikh, P. I.

    2013-06-01

    Tests were performed on a single cylinder, four stroke, direct injection, diesel engine whose piston crown, cylinder head and valves were coated with a 0.5 mm thickness of 3Al2O3·2SiO2 (mullite) (Al2O3 = 60%, SiO2 = 40%) over a 150 μm thickness of NiCrAlY bond coat. The working conditions for the conventional engine (without coating) and LHR (mullite coated) engine were kept exactly same to ensure a comparison between the two configurations of the engine. This paper is intended to emphasis on performance and combustion characteristics of conventional and LHR (Mullite coated) diesel engines under identical conditions. Tests were carried out at same operational constraints i.e. air-fuel ratio and engine speed conditions for both conventional engine (without coating) and LHR (mullite coated) engines. The results showed that, there was as much as 1.8 % increasing on brake power for LHR (mullite coated) engine compared to conventional engine (without coating) at full load The average decrease in brake specific fuel consumption in the LHR engine compared with the conventional engine was 1.76 % for full engine load. However, there was increasing on cylinder gas pressure and net heat release rate for LHR engine compared to conventional engine. Also the results revealed that, there was as much as 22% increasing on exhaust gas temperature for LHR engine compared to conventional engine at full engine load.

  18. Plasma sprayed coatings on crankshaft used steels

    Science.gov (United States)

    Mahu, G.; Munteanu, C.; Istrate, B.; Benchea, M.

    2017-08-01

    Plasma spray coatings may be an alternative to conventional heat treatment of main journals and crankpins of the crankshaft. The applications of plasma coatings are various and present multiple advantages compared to electric arc wire spraying or flame spraying. The study examines the layers sprayed with the following powders: Cr3C2- 25(Ni 20Cr), Al2O3- 13TiO2, Cr2O3-SiO2- TiO2 on the surface of steels used in the construction of a crankshaft (C45). The plasma spray coatings were made with the Spray wizard 9MCE facility at atmospheric pressure. The samples were analyzed in terms of micro and morphological using optical microscopy, scanning electron microscopy and X-ray diffraction. Wear tests on samples that have undergone simulates extreme working conditions of the crankshafts. In order to emphasize adherence to the base material sprayed layer, were carried out tests of microscratches and micro-indentation. Results have showed a relatively compact morphological aspect given by the successive coatings with splat-like specific structures. Following the microscratch analysis it can be concluded that Al2O3-13TiO2 coating has a higher purpose in terms of hardness compared to Cr3C2-(Ni 20Cr) and Cr2O3-SiO2- TiO2 powders. Thermal coatings of the deposited powders have increased the mechanical properties of the material. The results stand to confirm that plasma sprayed Al2O3-13TiO2 powder is in fact a efficient solution for preventing mechanical wear, even with a faulty lubrication system.

  19. Study of Multi-Function Micro-Plasma Spraying Technology

    Institute of Scientific and Technical Information of China (English)

    WANG Liuying; WANG Hangong; HUA Shaochun; CAO Xiaoping

    2007-01-01

    A multi-functional micro-arc plasma spraying system was developed according to aerodynamics and plasma spray theory. The soft switch IGBT (Insulated Gate Bipolar Transistor) invert technique, micro-computer control technique, convergent-divergent nozzle structure and axial powder feeding techniques have been adopted in the design of the micro-arc plasma spraying system. It is not only characterized by a small volume, a light weight, highly accurate control, high deposition efficiency and high reliability, but also has multi-functions in plasma spraying, welding and quenching. The experimental results showed that the system can produce a supersonic flame at a low power, spray Al2O3 particles at an average speed up to 430 m/s, and make nanostructured AT13 coatings with an average bonding strength of 42.7 MPa. Compared to conventional 9M plasma spraying with a higher power, the coatings with almost the same properties as those by conventional plasma spray can be deposited by multi-functional micro-arc plasma spraying with a lower power plasma arc due to an improved power supply design, spray gun structure and powder feeding method. Moreover, this system is suitable for working with thin parts and undertaking on site repairs, and as a result, the application of plasma spraying will be greatly extended.

  20. Radio Frequencv Induction Plasma Spraying of Molybdenum

    Institute of Scientific and Technical Information of China (English)

    Jiang Xianliang(蒋显亮); Maher Boulos

    2003-01-01

    Radio frequency (RF) induction plasma was used to make free-standing depositionof molybdenum (Mo). The phenomena of particle melting, flattening, and stacking were inves-tigated. The effect of process parameters such as plasma power, chamber pressure, and spraydistance on the phenomena mentioned above was studied. Scanning electron microscopy (SEM)was used to analyze the plasma-processed powder, splats formed, and deposits obtained. Exper-imental results show that less Mo particles are spheroidized when compared to the number ofspheroidized tungsten (W) particles at the same powder feed rate under the same plasma spraycondition. Molten Mo particles can be sufficiently flattened on substrate. The influence of theprocess parameters on the flattening behavior is not significant. Mo deposit is not as dense as Wdeposit, due to the splash and low impact of molten Mo particles. Oxidation of the Mo powderwith a large particle size is not evident under the low pressure plasma spray.

  1. Numerical Study of Suspension Plasma Spraying

    CERN Document Server

    Farrokhpanah, Amirsaman; Mostaghimi, Javad

    2016-01-01

    A numerical study of suspension plasma spraying (SPS) is presented in the current work. The liquid suspension jet is replaced with a train of droplets containing the suspension particles injected into the plasma flow. Atomization, evaporation, and melting of different components are considered for particles as they travel towards the substrate. Effect of different parameters on particle conditions during flight and upon impact on the substrate are investigated. Initially, influence of the torch operating conditions such as inlet flow rate and power are studied. Additionally, effect of injector parameters like injection location, flow rate, and angle are examined. The model used in current study takes high temperature gradients and non-continuum effects into account. Moreover, the important effect of change in physical properties of suspension droplets as a result of evaporation is included in the model. These mainly include variations in heat transfer properties and viscosity. Utilizing this improved model, s...

  2. Development of Expert Controller for Plasma Spraying Process

    Institute of Scientific and Technical Information of China (English)

    LIChun-xu; CHENKe-xuan; LIHe-qi; LIDe-wu

    2004-01-01

    Aiming at the plasma spraying process control, the control system model is developed on the basis of analyzing control parameters and coating properties and their correlation, and the corresponding control method and regulations are also given. With the developed expert controller for plasma spraying process, stable spraying can be realized using ordinary spraying powder and the coating of compaction, homogeneity and high bonding strength can be obtained.

  3. Characteristics of Plasma Spraying Torch with a Hollow Cathode

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    A kind of plasma spraying torch with a hollow cathode is described in this paper.The plasma torch can be used for axial powder injection in plasma spray studies. The arc characteristics of the plasma torch with various gas flowrates, different gas media, are presented. The mathematical modeling and computational method are developed for predicting the temperature and velocity field inside the plasma torch.

  4. Numerical Study of Suspension Plasma Spraying

    Science.gov (United States)

    Farrokhpanah, Amirsaman; Coyle, Thomas W.; Mostaghimi, Javad

    2017-01-01

    A numerical study of suspension plasma spraying is presented in the current work. The liquid suspension jet is replaced with a train of droplets containing the suspension particles injected into the plasma flow. Atomization, evaporation, and melting of different components are considered for droplets and particles as they travel toward the substrate. Effect of different parameters on particle conditions during flight and upon impact on the substrate is investigated. Initially, influence of the torch operating conditions such as inlet flow rate and power is studied. Additionally, effect of injector parameters like injection location, flow rate, and angle is examined. The model used in the current study takes high-temperature gradients and non-continuum effects into account. Moreover, the important effect of change in physical properties of suspension droplets as a result of evaporation is included in the model. These mainly include variations in heat transfer properties and viscosity. Utilizing this improved model, several test cases have been considered to better evaluate the effect of different parameters on the quality of particles during flight and upon impact on the substrate.

  5. Metal-mullite reactions

    Energy Technology Data Exchange (ETDEWEB)

    Loehman, R.E. [Sandia National Labs., Albuquerque, NM (United States); Tomsia, A.P. [Pask Research and Engineering, Berkeley, CA (United States)

    1993-11-01

    Mullite was reacted with pure Al and with Ti or Zr dissolved in Ag-Cu eutectic alloys at 1100 C in Ar. Analysis of the Ti and Zr-containing specimens showed reaction zones with compositions of Ti{sub 50}Cu{sub 3O}O{sub 20} and ZrO{sub 2}, respectively. The Al-mullite specimen showed much more extensive penetration into the ceramic and a more diffuse reaction zone than the other two systems. Al{sub 2}O{sub 3} and Si were the main reaction products for Al-mullite reaction.

  6. Thermomechanical processing of plasma sprayed intermetallic sheets

    Energy Technology Data Exchange (ETDEWEB)

    Hajaligol, Mohammad R. (Midlothian, VA); Scorey, Clive (Cheshire, CT); Sikka, Vinod K. (Oak Ridge, TN); Deevi, Seetharama C. (Midlothian, VA); Fleischhauer, Grier (Midlothian, VA); Lilly, Jr., A. Clifton (Chesterfield, VA); German, Randall M. (State College, PA)

    2001-01-01

    A powder metallurgical process of preparing a sheet from a powder having an intermetallic alloy composition such as an iron, nickel or titanium aluminide. The sheet can be manufactured into electrical resistance heating elements having improved room temperature ductility, electrical resistivity, cyclic fatigue resistance, high temperature oxidation resistance, low and high temperature strength, and/or resistance to high temperature sagging. The iron aluminide has an entirely ferritic microstructure which is free of austenite and can include, in weight %, 4 to 32% Al, and optional additions such as .ltoreq.1% Cr, .gtoreq.0.05% Zr .ltoreq.2% Ti, .ltoreq.2% Mo, .ltoreq.1% Ni, .ltoreq.0.75% C, .ltoreq.0.1% B, .ltoreq.1% submicron oxide particles and/or electrically insulating or electrically conductive covalent ceramic particles, .ltoreq.1% rare earth metal, and/or .ltoreq.3% Cu. The process includes forming a non-densified metal sheet by consolidating a powder having an intermetallic alloy composition such as by roll compaction, tape casting or plasma spraying, forming a cold rolled sheet by cold rolling the non-densified metal sheet so as to increase the density and reduce the thickness thereof and annealing the cold rolled sheet. The powder can be a water, polymer or gas atomized powder which is subjecting to sieving and/or blending with a binder prior to the consolidation step. After the consolidation step, the sheet can be partially sintered. The cold rolling and/or annealing steps can be repeated to achieve the desired sheet thickness and properties. The annealing can be carried out in a vacuum furnace with a vacuum or inert atmosphere. During final annealing, the cold rolled sheet recrystallizes to an average grain size of about 10 to 30 .mu.m. Final stress relief annealing can be carried out in the B2 phase temperature range.

  7. Thermal Expansion of Vacuum Plasma Sprayed Coatings

    Science.gov (United States)

    Raj, S V.; Palczer, A. R.

    2010-01-01

    Metallic Cu-8%Cr, Cu-26%Cr, Cu-8%Cr-1%Al, NiAl and NiCrAlY monolithic coatings were fabricated by vacuum plasma spray deposition processes for thermal expansion property measurements between 293 and 1223 K. The corrected thermal expansion, (DL/L(sub 0) varies with the absolute temperature, T, as (DL/L(sub 0) = A(T - 293)(sup 3) + BIT - 293)(sup 2) + C(T - 293) + D, where, A, B, C and D are thermal, regression constants. Excellent reproducibility was observed for all of the coatings except for data obtained on the Cu-8%Cr and Cu-26%Cr coatings in the first heat-up cycle, which deviated from those determined in the subsequent cycles. This deviation is attributed to the presence of residual stresses developed during the spraying of the coatings, which are relieved after the first heat-up cycle. In the cases of Cu-8%Cr and NiAl, the thermal expansion data were observed to be reproducible for three specimens. The linear expansion data for Cu-8% Cr and Cu-26%Cr agree extremely well with rule of mixture (ROM) predictions. Comparison of the data for the Cu-8%Cr coating with literature data for Cr and Cu revealed that the thermal expansion behavior of this alloy is determined by the Cu-rich matrix. The data for NiAl and NiCrAlY are in excellent agreement with published results irrespective of composition and the methods used for processing the materials. The implications of these results on coating GRCop-84 copper alloy combustor liners for reusable launch vehicles are discussed.

  8. Production of mullite fibers

    Science.gov (United States)

    Tucker, Dennis S. (Inventor); Sparks, J. Scott (Inventor)

    1991-01-01

    Disclosed here is a process for making mullite fibers wherein a hydrolizable silicon compound and an aluminum compound in the form of a difunctional aluminum chelate are hydrolized to form sols using water and an alcohol with a catalytic amount of hydrochloric acid. The sols are mixed in a molar ratio of aluminum to silicon of 3 to 1 and, under polycondensation conditions, a fibrous gel is formed. From this gel the mullite fibers can be produced.

  9. Directionally solidified mullite fibers

    Energy Technology Data Exchange (ETDEWEB)

    Sayir, A. [Case Western Reserve Univ., Cleveland, OH (United States); Farmer, S.C. [National Aeronautics and Space Administration, Cleveland, OH (United States). Lewis Research Center

    1995-10-01

    Directionally solidified fibers with nominal mullite compositions of 3Al{sub 2}O{sub 3} {center_dot} 2SiO{sub 2} were grown by the laser heated float zone (LHFZ) method at NASA Lewis. High resolution digital images from an optical microscope evidence the formation of a liquid-liquid miscibility gap during crystal growth. Experimental evidence shows that the formation of mullite in aluminosilicate melts is in fact preceded by liquid immiscibility. The average fiber tensile strength is 1.15 GPa at room temperature. The mullite fibers retained 80% of their room temperature tensile strength at 1,450 C. SEM analysis revealed that the fibers were strongly faceted and that the facets act as critical flaws. Examined in TEM, these mullite single crystals are free of dislocations, low angle boundaries and voids. Single crystal mullite showed a high degree of oxygen vacancy ordering. Regardless of the starting composition, the degree of order observed in polycrystalline fibers was lower than that observed in the mullite single crystals.

  10. Plasma spray for forming nanostructured thermal barrier coatings

    Institute of Scientific and Technical Information of China (English)

    LIN; Feng; JIANG; Xian-liang; YU; Yue-guang; ZENG; Ke-li; REN; Xian-jing

    2005-01-01

    Nanocrystalline powders of yttrium partially stabilized zirconia (YPSZ) are reprocessed into agglomerated feedstocks for plasma spraying thermal barrier coatings (TBCs), using the methods of ball milling, slurry dispersion, spray drying, and heat treatment. Atmospheric plasma is used to spray the agglomerated nanocrystalline particle feedstocks and coatings were deposited on the substrate of Ni-based superalloy. Scanning electron microscopy (SEM) is used to examine the morphology and cross-section of the agglomerated feedstocks and the free-section and cross-section of the nanostructured TBCs. Experimental results show that the agglomerated nanocrystalline particles are spherical and dense. Unlike conventional plasma-sprayed coatings, the micron/nano/micron sandwich structure can be found in the nanostructured YPSZ coatings deposited by atmospheric plasma spraying.

  11. Gas Permeability of Porous Plasma-Sprayed Coatings

    Science.gov (United States)

    Wittmann-Ténèze, K.; Caron, N.; Alexandre, S.

    2008-12-01

    For different applications, such as solid oxide fuel cells, there is an interest in understanding the relationship between the microstructure and the gas permeability of plasma-sprayed coatings. Nevertheless, plasma spraying processes allow to elaborate coatings with singular microstructures, depending strongly on the initial material and plasma operating conditions. And so, the evolution of permeability is not directly linked to the porosity. In this work, coatings were manufactured using different initial feedstock and spray parameters to obtain various microporous structures. Measurements of their permeation with the pressure drop method and their open porosity just as the observation of the morphology and the structure by optical microscopy were achieved. The different data show that the evolution of the gas permeability with the open porosity follows the Kozeny-Carman equation. This result correlated with the microstructural observation highlights the relationship between the permeability and the physical properties of porous plasma-sprayed layers.

  12. Research of Plasma Spraying Process on Aluminum-Magnesium Alloy

    Directory of Open Access Journals (Sweden)

    Patricija Kavaliauskaitė

    2016-04-01

    Full Text Available The article examines plasma sprayed 95Ni-5Al coatings on alu-minum-magnesium (Mg ≈ 2,6‒3,6 % alloy substrate. Alumi-num-magnesium samples prior spraying were prepared with mechanical treatment (blasting with Al2O3. 95Ni-5Al coatings on aluminum-magnesium alloys were sprayed with different parameters of process and coating‘s thickness, porosity, micro-hardness and microstructure were evaluated. Also numerical simulations in electric and magnetic phenomena of plasma spray-ing were carried out.

  13. Microstructure and Properties of Plasma Spraying Boron Carbide Coating

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Microstructure of plasma spray boron carbide coating was studied by SEM and TEM. Its physical,mechanical and electrical properties were measured. The results showed that high microhardness,modulus and Iow porosity of B4C coating were manufactured by plasma spray. It was lamellar packing and dense. The B4C coating examined here contained two principal structures and two impurity phase besides major phase. The relatively small value of Young′s modulus, comparing with that of the bulk materials, is explained by porosity. The Fe impurity phase could account for the relatively high electrical conductivity of boron carbide coating by comparing with the general boron carbide materials.

  14. Metallurgy and properties of plasma spray formed materials

    Science.gov (United States)

    Mckechnie, T. N.; Liaw, Y. K.; Zimmerman, F. R.; Poorman, R. M.

    1992-01-01

    Understanding the fundamental metallurgy of vacuum plasma spray formed materials is the key to enhancing and developing full material properties. Investigations have shown that the microstructure of plasma sprayed materials must evolve from a powder splat morphology to a recrystallized grain structure to assure high strength and ductility. A fully, or near fully, dense material that exhibits a powder splat morphology will perform as a brittle material compared to a recrystallized grain structure for the same amount of porosity. Metallurgy and material properties of nickel, iron, and copper base alloys will be presented and correlated to microstructure.

  15. Plasma sprayed and electrospark deposited zirconium metal diffusion barrier coatings

    Energy Technology Data Exchange (ETDEWEB)

    Hollis, Kendall J [Los Alamos National Laboratory; Pena, Maria I [Los Alamos National Laboratory

    2010-01-01

    Zirconium metal coatings applied by plasma spraying and electrospark deposition (ESD) have been investigated for use as diffusion barrier coatings on low enrichment uranium fuel for research nuclear reactors. The coatings have been applied to both stainless steel as a surrogate and to simulated nuclear fuel uranium-molybdenum alloy substrates. Deposition parameter development accompanied by coating characterization has been performed. The structure of the plasma sprayed coating was shown to vary with transferred arc current during deposition. The structure of ESD coatings was shown to vary with the capacitance of the deposition equipment.

  16. Preparation of thermal barrier coatings by ultrasonic plasma spraying

    Institute of Scientific and Technical Information of China (English)

    WEN Xiong-wei; LI Lu-ming; ZHANG Hua-tang; HAO Hong-wei; LU Zhi-qing

    2004-01-01

    Modulated plasma arc not only can heat the powder, but also can excite ultrasonic of different frequencies and different powers. The principles and characters of the plasma arc-excited ultrasonic were described, and the ultrasonic plasma spraying was compared with normal plasma spraying. Zirconia thermal barrier coatings (TBCs) were fabricated with two kinds of method. The TBCs were studied by the optical microscope observation, SEM observation and bonding strength experiment. The results show that suitable ultrasonic changes the performance and microstructure of TBCs in evidence. And the mechanism of ultrasonic influencing the TBCs was also discussed.

  17. Preparation of mullite fiber

    Energy Technology Data Exchange (ETDEWEB)

    Chen, L.; Wang, B.; Liu, S.; Yan, Y. [Xiamen Univ. (China). Dept. of Chemistry

    1996-06-01

    Transparent mullite fibers have been prepared using aluminum carboxylates (ACs) and tetraethyl orthosilicate (TEOS) as starting materials. The ACs are derived from the catalyzed dissolution of elemental aluminum in a mixture of formic acid and acetic acid. The solubility of aluminum in the acids is influenced by the concentrations of the acids, water, and additives and the preparation temperature. A 1:4:3:24 molar ratio of aluminum, formic acid, acetic acid, and water dissolves the aluminum completely to give a colorless, clear solution suitable for fiber synthesis. The mixture of the ACs and TEOS, in the presence of ethyl alcohol as a mutual solvent at 50--60 C, is concentrated to give a spinnable dope, from which mullite precursor fibers can be drawn. Heat treatment of the precursor at 1,250 C yields crystallized and transparent mullite fibers.

  18. Alignment Fixtures For Vacuum-Plasma-Spray Gun

    Science.gov (United States)

    Woodford, William H.; Mckechnie, Timothy N.; Power, Christopher A.; Daniel, Ronald L., Jr.

    1993-01-01

    Fixtures for alignment of vacuum-plasma-spray guns built. Each fixture designed to fit specific gun and holds small, battery-powered laser on centerline of gun. Laser beam projects small red dot where centerline intersects surface of workpiece to be sprayed. After laser beam positioned on surface of workpiece, fixture removed from gun and spraying proceeds.

  19. Preventing Clogging In A Vacuum Plasma Spray Gun

    Science.gov (United States)

    Krotz, Phillip D.; Daniel, Ronald L., Jr.; Davis, William M.

    1994-01-01

    Modification of powder-injection ports enables lengthy, high-temperature deposition operations. Graphite inserts prevent clogging of ports through which copper powder injected into vacuum plasma spray (VPS) gun. Graphite liners eliminate need to spend production time refurbishing VPS gun, reducing cost of production and increasing productivity. Concept also applied to other material systems used for net-shape fabrication via VPS.

  20. Modelling the Plasma Jet in Multi-Arc Plasma Spraying

    Science.gov (United States)

    Bobzin, K.; Öte, M.; Schein, J.; Zimmermann, S.; Möhwald, K.; Lummer, C.

    2016-08-01

    Particle in-flight characteristics in atmospheric plasma spraying process are determined by impulse and heat energy transferred between the plasma jet and injected powder particles. One of the important factors for the quality of the plasma-sprayed coatings is thus the distribution of plasma gas temperatures and velocities in plasma jet. Plasma jets generated by conventional single-arc plasma spraying systems and their interaction with powder particles were subject matter of intensive research. However, this does not apply to plasma jets generated by means of multi-arc plasma spraying systems yet. In this study, a numerical model has been developed which is designated to dealing with the flow characteristics of the plasma jet generated by means of a three-cathode spraying system. The upstream flow conditions, which were calculated using a priori conducted plasma generator simulations, have been coupled to the plasma jet simulations. The significances of the relevant numerical assumptions and aspects of the models are analyzed. The focus is placed on to the turbulence and diffusion/demixing modelling. A critical evaluation of the prediction power of the models is conducted by comparing the numerical results to the experimental results determined by means of emission spectroscopic computed tomography. It is evident that the numerical models exhibit a good accuracy for their intended use.

  1. Reliability of plasma-sprayed coatings: monitoring the plasma spray process and improving the quality of coatings

    Science.gov (United States)

    Fauchais, P.; Vardelle, M.; Vardelle, A.

    2013-06-01

    As for every coating technology, the reliability and reproducibility of coatings are essential for the development of the plasma spraying technology in industrial manufacturing. They mainly depend on the process reliability, equipment and spray booth maintenance, operator training and certification, implementation and use of consistent production practices and standardization of coating testing. This paper deals with the first issue, that is the monitoring and control of the plasma spray process; it does not tackle the coating characterization and testing methods. It begins with a short history of coating quality improvement under plasma spray conditions over the last few decades, details the plasma spray torches used in the industry, the development of the measurements of in-flight and impacting particle parameters and then of sensors. It concludes with the process maps that describe the interrelations between the operating parameters of the spray process, in-flight particle characteristics and coating properties and with the potential of in situ monitoring of the process by artificial neural networks and fuzzy logic methods.

  2. Influence of corn flour as pore forming agent on porous ceramic material based mullite: Morphology and mechanical properties

    Directory of Open Access Journals (Sweden)

    Ayala-Landeros J.G.

    2016-01-01

    Full Text Available Porous material was processed by the mixing, molding and pressing the ceramic material, afterward burnout and sintering; through the forming porous, using corn flour at different concentration (10, 15 and 20 wt.% as a pore forming agent; in order to determinate the influence of porous on the mechanical, morphological and structural properties. The effect of the volume fraction of corn flour in the mullite matrix, at various sintering temperature from 1100, 1200, 1300 and 1500°C were tested by Diffraction X ray, showing changes in crystalline phases of mullite (3Al2O3-2SiO2, as result of sintered temperatures. Presence of talcum powder in formula, also cause the formation of the cordierite and cristobalite crystalline phases, giving stability and adhesion to the structure of ceramic material. When sintering at temperatures between 1300 to 1500°C, and it was used the concentration of corn flour 15-20 wt.% as forming agent porous, it was found the better mechanical properties. The scanning electron microscopy analysis shows the presence of open porosity and anisotropy.

  3. Characterization of plasma sprayed beryllium ITER first wall mockups

    Energy Technology Data Exchange (ETDEWEB)

    Castro, R.G.; Vaidya, R.U.; Hollis, K.J. [Los Alamos National Lab., NM (United States). Material Science and Technology Div.

    1998-01-01

    ITER first wall beryllium mockups, which were fabricated by vacuum plasma spraying the beryllium armor, have survived 3000 thermal fatigue cycles at 1 MW/m{sup 2} without damage during high heat flux testing at the Plasma Materials Test Facility at Sandia National Laboratory in New Mexico. The thermal and mechanical properties of the plasma sprayed beryllium armor have been characterized. Results are reported on the chemical composition of the beryllium armor in the as-deposited condition, the through thickness and normal to the through thickness thermal conductivity and thermal expansion, the four-point bend flexure strength and edge-notch fracture toughness of the beryllium armor, the bond strength between the beryllium armor and the underlying heat sink material, and ultrasonic C-scans of the Be/heat sink interface. (author)

  4. Nanostructured yttria stabilized zirconia coatings deposited by air plasma spraying

    Institute of Scientific and Technical Information of China (English)

    ZHOU Hong; LI Fei; HE Bo; WANG Jun; SUN Bao-de

    2007-01-01

    Nanostructured yttria partially stabilized zirconia coatings were deposited by air plasma spraying with reconstituted nanosized powder. The microstructures and phase compositions of the powder and the as-sprayed nanostructured coatings were characterized by transmission electron microscopy(TEM), scanning electron microscopy(SEM) and X-ray diffraction(XRD). The results demonstrate that the microstructure of as-sprayed nanostructured zirconia coating exhibits a unique tri-modal distribution including the initial nanostructure of the powder, equiaxed grains and columnar grains. Air plasma sprayed nanostructured zirconia coatings consist of only the nontransformable tetragonal phase, though the reconstituted nanostructured powder shows the presence of the monoclinic, the tetragonal and the cubic phases. The mean grain size of the coating is about 42 nm.

  5. Nanostructured Sulfide Composite Coating Prepared by Atmospheric Plasma Spraying

    Institute of Scientific and Technical Information of China (English)

    关耀辉

    2006-01-01

    Nanostructured FeS-SiC coating was deposited by atmospheric plasma spraying (APS). The microstructure and phase composition of the coating were characterized with SEM and XRD, respectively. In addition, the size distribution of the reconstituted powders and the porosity of the coating have been measured. It was found that the reconstitiuted powers with sizes in the range of 20 to 80 μm had excellent flowability and were suitable for plasma spraying process. The assprayed FeS-SiC composite coating exhibited a bimodal distribution with small grains (30~80nm) and large grains (100~200nm). The coating was mainly composed of FeS and SiC, a small quantity of Fe1-x S and oxide were also found. The porosity of the coating was approximately 19 %.

  6. Plasma-sprayed ceramic coatings for molten metal environments.

    Energy Technology Data Exchange (ETDEWEB)

    Hollis, K. J. (Kendall J.); Peters, M. I. (Maria I.); Bartram, B. D. (Brian D.)

    2002-01-01

    Coating porosity is an important parameter to optimize for plasma-sprayed ceramics which are intended for service in molten metal environments. Too much porosity and the coatings may be infiltrated by the molten metal causing corrosive attack of the substrate or destruction of the coating upon solidification of the metal. Too little porosity and the coating may fail due to its inability to absorb thermal strains. This study describes the testing and analysis of tungsten rods coated with aluminum oxide, yttria-stabilized zirconia, yttrium oxide, and erbium oxide deposited by atmospheric plasma spraying. The samples were immersed in molten aluminum and analyzed after immersion. One of the ceramic materials used, yttrium oxide, was heat treated at 1000 C and 2000 C and analyzed by X-ray diffractography and mercury intrusion porosimetry. Slight changes in crysl nl structure and significant changes in porosity were observed after heat treatments.

  7. Plasma spray forming of tungsten coatings on copper electrodes

    Institute of Scientific and Technical Information of China (English)

    JIANG Xian-liang(蒋显亮); F.Gitzhofer; M.I.Boulos

    2004-01-01

    Both direct current dc plasma and radio frequency induction plasma were used to deposit tungsten coatings on copper electrodes. Fine tungsten powder with mean particle size of 5μm and coarse tungsten powder with particle size in the range from 45 μm to 75 μm were used as plasma spray feedstock. It is found that dc plasma is only applicable to spray the fine tungsten powder and induction plasma can be used to spray both the coarse powder and the fine powder. The tungsten coating deposited by the induction plasma spraying of the coarse powder is extremely dense. Such a coating with an interlocking structure and an integral interface with the copper substrate demonstrates high cohesion strength and adhesion strength.

  8. Vacuum plasma spray applications on liquid fuel rocket engines

    Science.gov (United States)

    Mckechnie, T. N.; Zimmerman, F. R.; Bryant, M. A.

    1992-01-01

    The vacuum plasma spray process (VPS) has been developed by NASA and Rocketdyne for a variety of applications on liquid fuel rocket engines, including the Space Shuttle Main Engine. These applications encompass thermal barrier coatings which are thermal shock resistant for turbopump blades and nozzles; bond coatings for cryogenic titanium components; wear resistant coatings and materials; high conductivity copper, NaRloy-Z, combustion chamber liners, and structural nickel base material, Inconel 718, for nozzle and combustion chamber support jackets.

  9. Fluctuation Phenomenon Analysis of an Arc Plasma Spraying Jet

    Institute of Scientific and Technical Information of China (English)

    赵文华; 田阔; 刘笛; 张冠忠

    2001-01-01

    The effects of three factors, including the power supply, the arc behaviour in the arc channel and the fluid dynamic process of the jet, on a plasma spraying jet have been experimentally detected by means of spectroscopic diagnostic techniques. The fast Fourier transform method has been applied to the analysis of the arc voltage and spectral line intensity of the jet. The three factors have been studied and distinguished from each other.

  10. Corrosion behavior of magnetic ferrite coating prepared by plasma spraying

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Yi; Wei, Shicheng, E-mail: wsc33333@163.com; Tong, Hui; Tian, Haoliang; Liu, Ming; Xu, Binshi

    2014-12-15

    Graphical abstract: The saturation magnetization (M{sub s}) of the ferrite coating is 34.417 emu/g while the M{sub s} value of the ferrite powder is 71.916 emu/g. It can be seen that plasma spray process causes deterioration of the room temperature soft magnetic properties. - Highlights: • Spinel ferrite coatings have been prepared by plasma spraying. • The coating consists of nanocrystalline grains. • The saturation magnetization of the ferrite coating is 34.417 emu/g. • Corrosion behavior of the ferrite coating was examined in NaCl solution. - Abstract: In this study, spray dried spinel ferrite powders were deposited on the surface of mild steel substrate through plasma spraying. The structure and morphological studies on the ferrite coatings were carried out using X-ray diffraction, scanning electron microscope and Raman spectroscopy. It was showed that spray dried process was an effective method to prepare thermal spraying powders. The coating showed spinel structure with a second phase of LaFeO{sub 3}. The magnetic property of the ferrite samples were measured by vibrating sample magnetometer. The saturation magnetization (M{sub s}) of the ferrite coating was 34.417 emu/g. The corrosion behavior of coating samples was examined by electrochemical impedance spectroscopy. EIS diagrams showed three corrosion processes as the coating immersed in 3.5 wt.% NaCl solution. The results suggested that plasma spraying was a promising technology for the production of magnetic ferrite coatings.

  11. Structural and dynamic properties of LiNO3 + Al2O3 nanocomposites

    Science.gov (United States)

    Gafurov, M. M.; Rabadanov, K. Sh.; Ataev, M. B.; Amirov, A. M.; Kubataev, Z. Yu.; Kakagasanov, M. G.

    2015-10-01

    The structural and dynamic properties of lithium nitrate LiNO3 and its heterogeneous composites with a nanopowder of aluminum oxide Al2O3 at different temperatures, phase states, and concentrations of the Al2O3 nanopowder have been investigated using Raman scattering, differential thermal analysis, and X-ray diffraction. It has been shown that, in the (1- x)LiNO3 + xAl2O3 composites, an amorphous phase (for x ≥ 0.5) is formed, whose thermal effect is observed at 185°C. The calculations of the dynamic characteristics of vibrations of the nitrate ion, as well as the differential thermal and X-ray diffraction analyses, have demonstrated that the nanocomposite can be represented as a highly disordered "quasilattice" in which "sites" are occupied by nanoparticles with amorphous lithium nitrate shells and spaces between them (conventionally "interstitial sites") become channels of a facilitated flow of the ion current.

  12. Preparation and Characterization of Fe2O3/Al2O3 Nano-composites

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Al2O3/Fe2O3 nano-composites were prepared by sol-gel route. The effect of Fe2O3 content on the structure, grain size and characterization of the composite were investigated through X-ray diffraction and M(o)ssbauer spectrum. The X-ray diffraction results show that Al2O3/Fe2O3 nano-composites with the Fe2O3, content of 40 wt% can be obtained after heat-treated at 900℃. The M(o)ssbauer effect results show that all samples exhibit clear super-paramagnetic phenomenon. Particles grow and defects reduce with the increasing of Fe2O3 conteni and some α-Fe2O3 stay magnetic order.

  13. Study of the KNO3-Al2O3 system by differential scanning calorimetry

    Science.gov (United States)

    Amirov, A. M.; Gafurov, M. M.; Rabadanov, K. Sh.

    2016-09-01

    The structural and the thermodynamic properties of potassium nitrate KNO3 and its composites with nanosized aluminum oxide Al2O3 have been studied by differential scanning calorimetry. It has been found that an amorphous phase forms in composites (1- x)KNO3- x Al2O3. The thermal effect corresponding to this phase has been observed at 316°C. It has been found that the phase transition heats of potassium nitrate decreased as the aluminum oxide fraction increased.

  14. Microstructure of Suspension Plasma Spray and Air Plasma Spray Al2O3-ZrO2 Composite Coatings

    Science.gov (United States)

    Chen, Dianying; Jordan, Eric H.; Gell, Maurice

    2009-09-01

    Al2O3-ZrO2 coatings were deposited by the suspension plasma spray (SPS) molecularly mixed amorphous powder and the conventional air plasma spray (APS) Al2O3-ZrO2 crystalline powder. The amorphous powder was produced by heat treatment of molecularly mixed chemical solution precursors below their crystallization temperatures. Phase composition and microstructure of the as-synthesized and heat-treated SPS and APS coatings were characterized by XRD and SEM. XRD analysis shows that the as-sprayed SPS coating is composed of α-Al2O3 and tetragonal ZrO2 phases, while the as-sprayed APS coating consists of tetragonal ZrO2, α-Al2O3, and γ-Al2O3 phases. Microstructure characterization revealed that the Al2O3 and ZrO2 phase distribution in SPS coatings is much more homogeneous than that of APS coatings.

  15. Evaluation of Performance and Emission characteristics of Turbocharged Diesel Engine with Mullite as Thermal Barrier Coating

    Directory of Open Access Journals (Sweden)

    P. N. Shrirao

    2011-06-01

    Full Text Available Tests were performed on a single cylinder, four stroke, direct injection, diesel engine whose piston crown, cylinder head and valves were coated with a 0.5 mm thickness of 3Al2O3 .2SiO2 (mullite (Al2O3= 60%, SiO2= 40% over a 150 μm thickness of NiCrAlY bond coat. Tests were carried out on standard engine (uncoated and low heatrejection (LHR engine with and without turbocharger. This paper is intended to emphasis on energy balance and emission characteristic for standard engine (uncoated and low heat rejection (LHR engine with and without turbocharger. Tests were carried out at different engine load and engine speed conditions for standard and low heatrejection engine with and without turbocharger. The results showed that there was 2.18% decreasing on specific fuel consumption value of low heat rejection (LHR engine with turbocharger compared to standard engine at full load. There was as much as 12% increasing on exhaust gas temperature of LHR engine with turbocharger compared tostandard engine at full load. There was as much as 20.64% increasing on NOx emission of exhaust gas, 22.05% decreasing on CO emission of exhaust gas and 28.20% decreasing on HC emission of exhaust gas of LHR engine with turbocharger compared to standard engine at full load.

  16. Residual stress in plasma sprayed ceramic turbine tip and gas path seal specimens

    Science.gov (United States)

    Hendricks, R. C.; Mcdonald, G.; Mullen, R. L.

    1983-01-01

    The residual stresses in a ceramic sheet material used for turbine blade tip gas path seals, were estimated. These stresses result from the plasma spraying process which leaves the surface of the sheet in tension. To determine the properties of plasma sprayed ZrO2-Y2O3 sheet material, its load deflection characteristics were measured. Estimates of the mechanical properties for sheet materials were found to differ from those reported for plasma sprayed bulk materials.

  17. Superhydrophobic Ceramic Coatings by Solution Precursor Plasma Spray

    Science.gov (United States)

    Cai, Yuxuan; Coyle, Thomas W.; Azimi, Gisele; Mostaghimi, Javad

    2016-04-01

    This work presents a novel coating technique to manufacture ceramic superhydrophobic coatings rapidly and economically. A rare earth oxide (REO) was selected as the coating material due to its hydrophobic nature, chemical inertness, high temperature stability, and good mechanical properties, and deposited on stainless steel substrates by solution precursor plasma spray (SPPS). The effects of various spraying conditions including standoff distance, torch power, number of torch passes, types of solvent and plasma velocity were investigated. The as-sprayed coating demonstrated a hierarchically structured surface topography, which closely resembles superhydrophobic surfaces found in nature. The water contact angle on the SPPS superhydrophobic coating was up to 65% higher than on smooth REO surfaces.

  18. Monoclinic zirconia distributions in plasma-sprayed thermal barrier coatings

    Science.gov (United States)

    Lance, M. J.; Haynes, J. A.; Ferber, M. K.; Cannon, W. R.

    2000-03-01

    Phase composition in an air plasma-sprayed Y2O3-stabilized ZrO2 (YSZ) top coating of a thermal barrier coating (TBC) system was characterized. Both the bulk phase content and localized pockets of monoclinic zirconia were measured with Raman spectroscopy. The starting powder consisted of ˜15 vol.% monoclinic zirconia, which decreased to ˜2 vol.% in the as-sprayed coating. Monoclinic zirconia was concentrated in porous pockets that were evenly distributed throughout the TBC. The pockets resulted from the presence of unmelted granules in the starting powder. The potential effect of the distributed monoclinic pockets on TBC performance is discussed.

  19. Plasma sprayed Fe(76)Nd(16)B(8) permanent magnets

    Science.gov (United States)

    Overfelt, R. A.; Anderson, C. D.; Flanagan, W. F.

    1986-01-01

    Thin coatings (0.16 mm) and thick coatings (0.50 mm) of Fe(76)Nd(16)B(8) were deposited on stainless-steel substrates by low pressure plasma spraying. Microscopic examination of the coatings in a light microscope revealed excessive porosity, but good bonding to the substrate. Fracture cross sections examined in a scanning electron microscope showed the grains to be equiaxed and approximately 1 micron or less in diameter in the as-sprayed condition. The intrinsic coercivities of the as-sprayed coatings varied from 5.8 to 10.9 kOe. The effects of postspray heat treatments on the intrinsic coercivity are also given.

  20. Plasma spray forming of functionally graded materials mould

    Institute of Scientific and Technical Information of China (English)

    ZHAO Zi-yu; FANG Jian-cheng; LI Hong-you

    2005-01-01

    A new technology of functionally graded materials(FGM) mould fabricated by plasma spraying and arc spraying was developed. According to applied characteristic of plastic mould, the reasonable coatings of FGM were designed and their microstructures were analyzed. At the same time, some key problems were solved including spray mould fabricating, FGM forming and demoulding, etc. The results show that the service performance of the FGM mould is much more excellent than the one composed of the traditional materials, and the life span can also be greatly increased. The technology will have a significant influence on materials development in mould industry.

  1. Suspension plasma sprayed composite coating using amorphous powder feedstock

    Science.gov (United States)

    Chen, Dianying; Jordan, Eric H.; Gell, Maurice

    2009-03-01

    Al 2O 3-ZrO 2 composite coatings were deposited by the suspension plasma spray process using molecularly mixed amorphous powders. X-ray diffraction (XRD) analysis shows that the as-sprayed coating is composed of α-Al 2O 3 and tetragonal ZrO 2 phases with grain sizes of 26 nm and 18 nm, respectively. The as-sprayed coating has 93% density with a hardness of 9.9 GPa. Heat treatment of the as-sprayed coating reveals that the Al 2O 3 and ZrO 2 phases are homogeneously distributed in the composite coating.

  2. Laser Remelting of Plasma Sprayed Thermal Barrier Coatings

    Institute of Scientific and Technical Information of China (English)

    Gang ZHANG; Yong LIANG; Yingna WU; Zhongchao FENG; Bingchun ZHANG; Fangjun LIU

    2001-01-01

    A CO2 continuous wave laser with defocused beam was used for remelting the surface of plasma sprayed ZrO2-8 wt pct Y2O3 (8YSZ)/Ni22Cr10AlY thermal barrier coatings (TBCs) on GH536 superalloy substrate. Two main laser processing parameters, power and travel speed, were adopted to produce a completely remelted layer, and their effects on remelted appearance,remelting depth, density and diameter of depression, space of segment crack and remelted microstructure were evaluated. With energy of 4.0 to 8.0 J.mm-2, an appropriate laser processing for applicable remelted layer was suggested.

  3. Comparison of W–TiC composite coatings fabricated by atmospheric plasma spraying and supersonic atmospheric plasma spraying

    Energy Technology Data Exchange (ETDEWEB)

    Hou, Qing Yu, E-mail: qingyuhou@hotmail.com [School of Material Science and Engineering, Hefei University of Technology, Hefei, Anhui 230009 (China); Anhui Key Laboratory of Metal Materials and Processing, Maanshan, Anhui 243002 (China); Luo, Lai Ma [School of Material Science and Engineering, Hefei University of Technology, Hefei, Anhui 230009 (China); Huang, Zhen Yi; Wang, Ping; Ding, Ting Ting [Anhui Key Laboratory of Metal Materials and Processing, Maanshan, Anhui 243002 (China); Wu, Yu Cheng, E-mail: ycwu@hfut.edu.cn [School of Material Science and Engineering, Hefei University of Technology, Hefei, Anhui 230009 (China)

    2016-04-15

    Highlights: • W–TiC composite coatings were fabricated by APS and SAPS technologies. • TiC had filling effect on pores and coating/fixing effect on un-melted particles. • Porosity and oxygen content in SAPS coating were lower than that in APS coating. • Thermal conductivity of SAPS coating was higher than that of APS coating. • SAPS coating has better ability to resist to elastic fracture than APS coating does. - Abstract: Tungsten coatings with 1.5 wt.% TiC (W/TiC) were fabricated by atmospheric plasma spraying (APS) and supersonic atmospheric plasma spraying (SAPS) techniques, respectively. The results showed that the typical lamellar structure of plasma spraying and columnar crystalline grains formed in the coatings. Pores located mainly at lamellar gaps in association with oxidation were also observed. TiC phase, distributed at lamellar gaps filled the gaps; and that distributed around un-melted tungsten particles and splashed debris coated the particles or debris that were linked with the TiC at lamellar gaps. The coating and linking of the retained TiC phase prevented the tungsten particles to come off from the coatings. The porosity and the oxygen content of the SAPS-W/TiC were lower than those of the APS-W/TiC coating. The mechanical response of the coatings was strongly dependent on the H/E* ratio (H and E* are the hardness and effective Young’s modulus, respectively). The SAPS-W/TiC coating with a higher H/E* ratio had a better ability to resist to elastic fracture and better fracture toughness as compared with the APS-W/TiC coating with a smaller H/E* ratio. The thermal conductivity of the SAPS-W/TiC coating was greater than that of the APS-W/TiC coating.

  4. Development of plasma spray coating using coal ash

    Energy Technology Data Exchange (ETDEWEB)

    Mishra, S.C.; Sarkar, P.C.; Mishra, P.C.; Sreekumar, K.P.; Padmanabhan, P.V.A. [Regional Engineering College, Rourkela (India)

    2000-07-01

    In India about 70 million tonnes of fly ash is generated annually and the figure is growing at a faster rate due to industrial and urban demand. Worldwide, fly ash is being used to generate value added products. In India about 10% of fly ash generated is utilised and if feverish activity is not initiated the percent utilisation can go down. The present piece of work has been undertaken to use the fly ash and graphite (from the rejected electrodes of arc furnaces) for developing plasma spray composite coating on metal substrates. Fly ash and graphite powder (at 10% and 20% wt) mix was plasma sprayed at various operating conditions of the plasma torch on different metal substrate, viz. copper and stainless steel. The coating thus formed was characterised by X-ray diffraction analysis, electron microscopy, microhardness measurement and measurement of interface adhesion strength. A maximum coating thickness of {approximately} 220 micron is obtained with fly ash +20% graphite. The adherence strength is found to vary between 10-35 MNm{sup 2} and is maximum in case of copper substrates. 8 refs., 4 figs., 1 tab.

  5. Plasma-Sprayed Titanium Patterns for Enhancing Early Cell Responses

    Science.gov (United States)

    Shi, Yunqi; Xie, Youtao; Pan, Houhua; Zheng, Xuebin; Huang, Liping; Ji, Fang; Li, Kai

    2016-06-01

    Titanium coating has been widely used as a biocompatible metal in biomedical applications. However, the early cell responses and long-term fixation of titanium implants are not satisfied. To obviate these defects, in this paper, micro-post arrays with various widths (150-1000 μm) and intervals (100-300 μm) were fabricated on the titanium substrate by template-assisted plasma spraying technology. In vitro cell culture experiments showed that MC3T3-E1 cells exhibited significantly higher osteogenic differentiation as well as slightly improved adhesion and proliferation on the micro-patterned coatings compared with the traditional one. The cell number on the pattern with 1000 µm width reached 130% after 6 days of incubation, and the expressions of osteopontin (OPN) as well as osteocalcin (OC) were doubled. No obvious difference was found in cell adhesion on various size patterns. The present micro-patterned coatings proposed a new modification method for the traditional plasma spraying technology to enhance the early cell responses and convenience for the bone in-growth.

  6. Anisotropic resistivity in plasma-sprayed silicon thick films

    Science.gov (United States)

    Kharas, Boris Dave; Sampath, Sanjay; Gambino, Richard J.

    2005-05-01

    Silicon thick films deposited by thermal plasma spray are of interest as inexpensive electronic materials for conformal meso-scale electronics applications. In addition they also serve as a model system for the investigation of electrical properties of coatings with layered anisotropy. In this study impedance spectroscopy was used to measure the complex resistivity of free-standing 64μm-thick polycrystalline silicon films deposited by thermal plasma spraying in an atmospheric ambient. Impedance spectroscopy measurements were taken in the through-thickness (across-splat) and edge-to-edge (in-splat) directions and revealed a resistivity difference of approximately 7.5±0.23 between the two directions. The complex resistivity results are explained on the basis of a brick-layer type model, associated with the layered splat microstructure obtained from cross-sectional transmission electron microscope imaging of the films. In addition a circuit-based model made up of parallel, resistor-capacitor elements in series, and Cole-Cole and Davidson-Cole impedance functions were used to fit the impedance data to extract material parameters and contributions from the grains and splat boundaries. Furthermore, thermal processing and phosphorus doping is shown to lead to higher and lower resistivity, respectively, in the films.

  7. Superior Thermal Barrier Coatings Using Solution Precursor Plasma Spray

    Science.gov (United States)

    Jordan, E. H.; Xie, L.; Gell, M.; Padture, N. P.; Cetegen, B.; Ozturk, A.; Ma, X.; Roth, J.; Xiao, T. D.; Bryant, P. E. C.

    2004-03-01

    A novel process, solution precursor plasma spray (SPPS), is presented for depositing thermal barrier coatings (TBCs), in which aqueous chemical precursors are injected into a standard direct current plasma spray system. The resulting coatings microstructure has three unique features: (1) ultra fine splats (1 µm), (2) nanometer and micron-sized interconnected porosity, and (3) closely spaced, through-thickness cracks. Coatings over 3 mm thick can be readily deposited using the SPPS process. Coating durability is excellent, with SPPS coatings showing, in furnace cycling tests, 2.5 times the spallation life of air plasma coatings (APS) and 1.5 times the life of electron beam physical vapor deposited (EB-PVD) coatings. The conductivity of SPPS coatings is lower than EB-PVD coatings and higher than the best APS coatings. Manufacturing cost is expected to be similar to APS coatings and much lower than EB-PVD coatings. The SPPS deposition process includes droplet break-up and material arriving at the deposition surface in various physical states ranging from aqueous solution, gel phase, to fully-molten ceramic. The relation between the arrival state of the material and the microstructure is described.

  8. The technology of Plasma Spray Physical Vapour Deposition

    Directory of Open Access Journals (Sweden)

    M. Góral

    2012-12-01

    Full Text Available Purpose: The deposition of thermal barrier coatings is currently the most effective means of protecting the surface of aircraft engine turbine blades from the impact of aggressive environment of combustion gases. The new technologies of TBC depositions are required.Design/methodology/approach: The essential properties of the PS-PVD process have been outlined, as well as recent literature references. In addition, the influence of a set process condition on the properties of the deposited coatings has been described.Findings: The new plasma-spraying PS-PVD method is a promising technology for the deposition of modern thermal barrier coatings on aircraft engine turbine blades.Research limitations/implications: The constant progress of engine operating temperatures and increasing pollution restrictions determine the intensive development of heat-resistant coatings, which is directed to new deposition technologies and coating materials.Practical implications: The article presents a new technology of thermal barrier coating deposition - LPPS Thin Film and Plasma Spray - Physical Vapour Deposition.Originality/value: The completely new technologies was described in article.

  9. Reaction between mullite and polytitanocarbosilane

    Energy Technology Data Exchange (ETDEWEB)

    Hirata, Y.; Matsura, T. [Kagoshima Univ. (Japan). Dept. of Appl. Chem.; Shibuya, M. [Ube Industries Ltd., Tyranno Fiber Development Project (Japan)

    1999-03-01

    Infiltration and subsequent pyrolysis of inorganic polymer in the spaces of long fibers / mullite powder systems may be a successful processing method to reduce the damage of fibers and to decrease the shrinkage of the matrix during heating. This paper describes the chemical reaction between polytitanocarbosilane and mullite as a first step in the processing of mullite matrix composites. A mullite powder of 30 vol% was mixed with a polytitanocarbosilane (50 wt%) / xylene (50 wt%) solution for 24 h, and the suspension was formed into thick films by doctor blade. The green sheets were hot-pressed at 1400-1600 C in a N{sub 2} atmosphere. The composites consisted of mullite, sialon with a composition of Si{sub 2}Al{sub 3}O{sub 7}N or Si{sub 12}Al{sub 18}O{sub 39}N{sub 8}, {alpha}-Al{sub 2}O{sub 3}, {beta}-SiC and TiN. The formation of these phases were thermodynamically discussed in the system of mullite - C (supplied from polytitianocarbosilane) - N{sub 2}. (orig.) 11 refs.

  10. Superhydrophobic Ceramic Coatings by Solution Precursor Plasma Spray

    Science.gov (United States)

    Cai, Yuxuan

    Superhydrophobic surfaces exhibit superior water repellent properties, and they have remarkable potential to improve current energy infrastructure. Substantial research has been performed on the production of superhydrophobic coatings. However, superhydrophobic coatings have not yet been adopted in many industries where potential applications exist due to the limited durability of the coating materials and the complex and costly fabrication processes. Here presented a novel coating technique to manufacture ceramic superhydrophobic coatings rapidly and economically. A rare earth oxide (REO) was selected as the coating material due to its hydrophobic nature and strong mechanical properties, and deposited on stainless steel substrates by solution precursor plasma spray (SPPS). The as-sprayed coating demonstrated a hierarchically structured coating topography, which closely resembles superhydrophobic surfaces in nature. Compared to smooth REO surfaces, the SPPS superhydrophobic coating improved the water contact angle by as much as 65° after vacuum treatment at 1 Pa for 48 hours.

  11. Numerical Simulation of Basic Parameters in Plasma Spray

    Institute of Scientific and Technical Information of China (English)

    范群波; 王鲁; 王富耻

    2004-01-01

    On the basis of energy balance in the plasma gas, a new, simplified but effective mathematical model is developed to predict the temperature, velocity and ionization degrees of different species at the torch exit, which can be directly calculated just by inputting the general spraying parameters, such as current, voltage, flow rates of gases, etc. Based on this method, the effects of plasma current and the flow rate of Ar on the basic parameters at the torch exit are discussed. The results show that the temperature, velocity and ionization degrees of gas species will increase with increasing the plasma current; while increasing Ar flow rate can increase the velocity at the exit but decrease the temperature and ionization degrees of plasma species. The method would be helpful to predict the temperature and velocity fields in a plasma jet in future, and direct the practical plasma spray operations.

  12. Caracterisation of Titanium Nitride Layers Deposited by Reactive Plasma Spraying

    Science.gov (United States)

    Roşu, Radu Alexandru; Şerban, Viorel-Aurel; Bucur, Alexandra Ioana; Popescu, Mihaela; Uţu, Dragoş

    2011-01-01

    Forming and cutting tools are subjected to the intense wear solicitations. Usually, they are either subject to superficial heat treatments or are covered with various materials with high mechanical properties. In recent years, thermal spraying is used increasingly in engineering area because of the large range of materials that can be used for the coatings. Titanium nitride is a ceramic material with high hardness which is used to cover the cutting tools increasing their lifetime. The paper presents the results obtained after deposition of titanium nitride layers by reactive plasma spraying (RPS). As deposition material was used titanium powder and as substratum was used titanium alloy (Ti6Al4V). Macroscopic and microscopic (scanning electron microscopy) images of the deposited layers and the X ray diffraction of the coatings are presented. Demonstration program with layers deposited with thickness between 68,5 and 81,4 μm has been achieved and presented.

  13. Elastic behaviour of plasma sprayed thermal barrier coatings

    Energy Technology Data Exchange (ETDEWEB)

    Steinbrech, R.W.; Frahm, J.; Herzog, R.; Schubert, F. [Inst. for Materials and Processes in Energy Systems, Forschungszentrum Juelich GmbH, Juelich (Germany)

    2002-07-01

    The elastic behaviour of air plasma sprayed (APS) thermal barrier coatings (TBCs) of 8 wt.% yttria stabilised zirconia was studied using various mechanical tests with global and local resolution. Results are presented, which reveal the complex relationship between lamellar APS-microstructure and stiffness and illustrate scaling aspects. Also the influence of residual stresses is addressed. The obtained stiffness values for as-sprayed TBCs show a systematic variation between 10 and 100 GPa. Typically results from bending tests of free-standing TBCs are at the low end, whereas results from depth sensitive indentation tests with TBCs bonded to a substrate are found at the high end. When heat treated above 950 C the TBCs exhibit a rapid increase in stiffness which can be attributed to defect healing within the spraying lamellae. Discussion of the results focuses on the implications of a non-uniform stiffness modulus for the mechanical characterisation of thermal barrier systems. (orig.)

  14. Blanching resistant Cu-Cr coating by vacuum plasma spray

    Energy Technology Data Exchange (ETDEWEB)

    Chiang, K.T. [Rockwell International Corp., Canoga Park, CA (United States). Rocketdyne Div.; Krotz, P.D. [Rockwell International Corp., Canoga Park, CA (United States). Rocketdyne Div.; Yuen, J.L. [Rockwell International Corp., Canoga Park, CA (United States). Rocketdyne Div.

    1995-11-01

    Copper alloy rocket engine combustion chamber linings have been found to deteriorate when exposed to cyclic reducing oxidizing (redox) environments, which are a consequence of the combustion process. The deterioration, known as blanching, can be characterized by increased roughness and burn-through sites in the wall of the combustion chamber lining and can seriously reduce the operational lifetime of the combustion chamber. A Cu-30 vol.%Cr coating produced by vacuum plasma spraying was effective in protecting the copper alloy substrate against blanching. The coating properties were characterized after cyclic oxidation exposure to 650 C in air followed by high pressure hydrogen charging. When exposed to an oxidizing environment at high temperatures, the coating formed a protective chromia scale that was substantially unreduced by high pressure hydrogen. (orig.)

  15. Suspension plasma sprayed composite coating using amorphous powder feedstock

    Energy Technology Data Exchange (ETDEWEB)

    Chen Dianying [Department of Chemical, Materials and Biomolecular Engineering, Institute of Materials Science, University of Connecticut, 97 N Eagleville Rd U-3136, Storrs, CT 06269 (United States)], E-mail: chendy@ims.uconn.edu; Jordan, Eric H. [Department of Mechanical Engineering, University of Connecticut, Storrs, CT 06269 (United States); Gell, Maurice [Department of Chemical, Materials and Biomolecular Engineering, Institute of Materials Science, University of Connecticut, 97 N Eagleville Rd U-3136, Storrs, CT 06269 (United States)

    2009-03-15

    Al{sub 2}O{sub 3}-ZrO{sub 2} composite coatings were deposited by the suspension plasma spray process using molecularly mixed amorphous powders. X-ray diffraction (XRD) analysis shows that the as-sprayed coating is composed of {alpha}-Al{sub 2}O{sub 3} and tetragonal ZrO{sub 2} phases with grain sizes of 26 nm and 18 nm, respectively. The as-sprayed coating has 93% density with a hardness of 9.9 GPa. Heat treatment of the as-sprayed coating reveals that the Al{sub 2}O{sub 3} and ZrO{sub 2} phases are homogeneously distributed in the composite coating.

  16. Identification of Desirable Precursor Properties for Solution Precursor Plasma Spray

    Science.gov (United States)

    Muoto, Chigozie K.; Jordan, Eric H.; Gell, Maurice; Aindow, Mark

    2011-06-01

    In solution precursor plasma spray chemical precursor solutions are injected into a standard plasma torch and the final material is formed and deposited in a single step. This process has several attractive features, including the ability to rapidly explore new compositions and to form amorphous and metastable phases from molecularly mixed precursors. Challenges include: (a) moderate deposition rates due to the need to evaporate the precursor solvent, (b) dealing on a case by case basis with precursor characteristics that influence the spray process (viscosity, endothermic and exothermic reactions, the sequence of physical states through which the precursor passes before attaining the final state, etc.). Desirable precursor properties were identified by comparing an effective precursor for yttria-stabilized zirconia with four less effective candidate precursors for MgO:Y2O3. The critical parameters identified were a lack of major endothermic events during precursor decomposition and highly dense resultant particles.

  17. Plasma-sprayed ceramic coatings for protection against molten metal.

    Energy Technology Data Exchange (ETDEWEB)

    Hollis, K. J. (Kendall J.); Peters, M. I. (Maria I.); Bartram, B. D. (Brian D.)

    2002-01-01

    Molten metal environments pose a special demand on materials due to the high temperature corrosion effects and thermal expansion mismatch induced stress effects. A solution that has been successfully employed is the use of a base material for the mechanical strength and a coating material for the chemical compatibility with the molten metal. The work described here used such an approach coating tungsten rods with aluminum oxide, yttria-stabilized zirconia, yttrium oxide, and erbium oxide deposited by atmospheric plasma spraying. The ceramic materials were deposited under varying conditions to produce different structures. Measurement of particle characteristics was performed to correlate to material properties. The coatings were tested in a thermal cycling environment to simulate the metal melting cycle expected in service. Results of the testing indicate the effect of material composition and spray conditions on the thermal cycle crack resistance of the coatings.

  18. Sea water corrosion behavior of plasma sprayed abradable coatings

    Science.gov (United States)

    Parida, M.; Nanda, S. P.; Mishra, S. C.

    2017-02-01

    Aluminum based abradable coating is used for sealing purpose in compressor casing of aero engines to withstand up to a service temperature of 450°C. Al-BNSiO2 composite coating is deposited using thermal plasma spray technique. Coating thickness measured and porosity of the coating is evaluated.Coating morphology is observed and EDSanalysis is done with SEM (Jeol make). The effect of time on the sea water corrosion behavior of the coating is evaluated. It is observed that, there is a sharp increase in weight gain of the coating up to six weeks of immersion. This behavior is attributed to the adsorption/deposition of other elements/reactions taking place during interaction with sea water.

  19. Making Mullite Fibers By Airgap Wet Spinning

    Science.gov (United States)

    Tucker, Dennis S.; Sparks, J. Scott

    1991-01-01

    Proposed process makes continuous mullite fibers retaining structural integrity at temperatures up to and somewhat beyond 1,300 degrees C. Process makes highly pure mullite fibers, without melting and without dangerous solvent.

  20. Residual stress in plasma-sprayed ceramic turbine tip and gas-path seal specimens

    Science.gov (United States)

    Hendricks, R. C.; Mcdonald, G.; Mullen, R. L.

    1983-01-01

    The residual stresses in a ceramic sheet material used for turbine blade tip gas path seals, were estimated. These stresses result from the plasma spraying process which leaves the surface of the sheet in tension. To determine the properties of plasma sprayed ZrO2-Y2O3 sheet material, its load deflection characteristics were measured. Estimates of the mechanical properties for sheet materials were found to differ from those reported for plasma sprayed bulk materials. Previously announced in STAR as N83-28380

  1. Mechanical, In Vitro Antimicrobial and Biological Properties of Plasma Sprayed Silver-Doped Hydroxyapatite Coating

    OpenAIRE

    Roy, Mangal; Fielding, Gary A.; BEYENAL, Haluk; Bandyopadhyay, Amit; Bose, Susmita

    2012-01-01

    Implant related infection is one of the key concerns in total joint hip arthroplasties. In order to reduce bacterial adhesion, silver (Ag) / silver oxide (Ag2O) doping was used in plasma sprayed hydroxyapatite (HA) coating on titanium substrate. HA powder was doped with 2.0, 4.0 and 6.0 wt% Ag, heat treated at 800 °C and used for plasma spray coating using a 30 kW plasma spray system, equipped with supersonic nozzle. Application of supersonic plasma nozzle significantly reduced phase decompos...

  2. Plasma sprayed rutile titania-nanosilver antibacterial coatings

    Energy Technology Data Exchange (ETDEWEB)

    Gao, Jinjin [Key Lab of Inorganic Coating Materials, Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai 200050 (China); Zhao, Chengjian [National Key Laboratory of Human Factors Engineering, Department of ECLSS, China Astronaut Researching and Training Center, Beijing, 100094 (China); Zhou, Jingfang [Ian Wark Research Institute, University of South Australia, Mawson Lakes Campus, Mawson Lakes, SA, 5095 (Australia); Li, Chunxia [National Key Laboratory of Human Factors Engineering, Department of ECLSS, China Astronaut Researching and Training Center, Beijing, 100094 (China); Shao, Yiran; Shi, Chao [Key Lab of Inorganic Coating Materials, Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai 200050 (China); Zhu, Yingchun, E-mail: yzhu@mail.sic.ac.cn [Key Lab of Inorganic Coating Materials, Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai 200050 (China)

    2015-11-15

    Graphical abstract: - Highlights: • TiO{sub 2}/Ag feedstock powders containing 1–10,000 ppm silver nanoparticles were double sintered and deposited by plasma spray. • TiO{sub 2}/Ag coatings were composed of pure rutile phase and homogeneously-distributed metallic silver. • TiO{sub 2}/Ag coatings with more than 10 ppm silver nanoparticles exhibited strong antibacterial activity against E. coli and S. aureus. - Abstract: Rutile titania (TiO{sub 2}) coatings have superior mechanical properties and excellent stability that make them preferential candidates for various applications. In order to prevent infection arising from bacteria, significant efforts have been focused on antibacterial TiO{sub 2} coatings. In the study, titania-nanosilver (TiO{sub 2}/Ag) coatings with five different kinds of weight percentages of silver nanoparticles (AgNPs) were prepared by plasma spray. The feedstock powders, which had a composition of rutile TiO{sub 2} powders containing 1–10,000 ppm AgNPs, were double sintered and deposited on stainless steel substrates with optimized spraying parameters. X-Ray diffraction and scanning electron microscopy were used to analysize the phase composition and surface morphology of TiO{sub 2}/Ag powders and coatings. Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus) were employed to examine the antibacterial activity of the as-prepared coatings by bacterial counting method. The results showed that silver existed homogeneously in the TiO{sub 2}/Ag coatings and no crystalline changed happened in the TiO{sub 2} structure. The reduction ratios on the TiO{sub 2}/Ag coatings with 10 ppm AgNPs were as high as 94.8% and 95.6% for E. coli and S. aureus, respectively, and the TiO{sub 2}/Ag coatings with 100–1000 ppm AgNPs exhibited 100% bactericidal activity against E. coli and S. aureus, which indicated the TiO{sub 2}/Ag coatings with more than 10 ppm AgNPs had strong antibacterial activity. Moreover, the main factors influencing the

  3. Bonelike apatite coatings on plasma-sprayed porous titanium by biomimetic processing

    Institute of Scientific and Technical Information of China (English)

    SHI Jian-min; DING Chuan-xian

    2001-01-01

    @@ INTRODUCTION Hydroxyapatite (HA) has many biological benefits, such as direct bonding to bone and enhances new bone formation around it. It has been demonstrated that dental and orthopaedic implants coated with HA show superior histological results to the uncoated ones. Various methods as well as plasma spraying, which is commonly used, have been developed to coat HA on metals. However, Plasma-sprayed HA coatings are limited by specific drawbacks such as low crystallinity, weak bond strength to the substrate.

  4. Plasma Processes : Plasma sprayed alumina coatings for radiation detector development

    Indian Academy of Sciences (India)

    Mary Alex; V Balagi; K R Prasad; K P Sreekumar; P V Ananthapadmanabhan

    2000-11-01

    Conventional design of radiation detectors uses sintered ceramic insulating modules. The major drawback of these ceramic components is their inherent brittleness. Ion chambers, in which these ceramic spacers are replaced by metallic components with plasma spray coated alumina, have been developed in our Research Centre. These components act as thin spacers that have good mechanical strength as well as high electrical insulation and replace alumina insulators with the same dimensions. As a result, the design of the beam loss monitor ion chamber for CAT could be simplified by coating the outer surface of the HT electrode with alumina. One of the chambers developed for isotope calibrator for brachytherapy gamma sources has its outer aluminium electrode (60 mm dia × 220 mm long) coated with 250 thick alumina (97%) + titania (3%). In view of potential applications in neutron-sensitive ion chambers used in reactor control instrumentation, studies were carried out on alumina 100 to 500 thick coatings on copper, aluminium and SS components. The electrical insulation varied from 108 ohms to 1012 ohms for coating thicknesses above 200 . The porosity in the coating resulted in some fall in electrical insulation due to moisture absorption. An improvement could be achieved by providing the ceramic surface with moisture-repellent silicone oil coating. Irradiation at Apsara reactor core location showed that the coating on aluminium was found to be unaffected after exposure to 1017 nvt fluence.

  5. Vacuum Plasma Spray (VPS) Material Applications for Thruster Components

    Science.gov (United States)

    Elam, Sandra; Holmes, Richard; Hickman, Robert

    2006-01-01

    A variety of vacuum plasma spray (VPS) material systems have been successfully applied to injector and thrust chamber components. VPS offers a versatile fabrication process with relatively low costs to produce near net shape parts. The materials available with VPS increase operating margins and improve component life by providing superior thermal and oxidation protection in specific engine environments. Functional gradient materials (FGM) formed with VPS allow thrust chamber liners to be fabricated with GRCop-84 (an alloy of copper, chrome, and niobium) and a protective layer of NiCrAlY on the hot wall. A variety of thrust chamber liner designs have been fabricated to demonstrate the versatility of the process. Hot-fire test results have confined the improved durability and high temperature performance of the material systems for thrust chamber liners. Similar FGM s have been applied to provide superior thermal protection on injector faceplates with NiCrAlY and zirconia coatings. The durability of the applied materials has been demonstrated with hot-fire cycle testing on injector faceplates in high temperature environments. The material systems can benefit the components used in booster and main engine propulsion systems. More recent VPS efforts are focused on producing rhenium based material systems for high temperature applications to benefit in-space engines like reaction control system (RCS) thrusters.

  6. Plasma spray deposition of graded metal-ceramic coatings

    Energy Technology Data Exchange (ETDEWEB)

    Musil, J. (Inst. of Tech. and Reliability of Structures, Czechoslovak Academy of Sciences, Plzen (Czechoslovakia)); Fiala, J. (Central Research Inst., Plzen (Czechoslovakia))

    1992-05-20

    Plasma spraying of graded coatings is described and the metal-ceramic interface of the graded intermediate zone is analysed in terms of a simple physical model. Special attention is devoted to the dominant deposition parameters, powder characteristics and the injector configuration for powder feeding, which play a fundamental role in graded coating deposition with controlled formation of a metal-ceramic intermediate zone. On the basis of a knowledge of these parameters, a new and original formula for the coefficient of homogeneity for simultaneous deposition of metal and ceramic particles at the same spot on the substrate is derived. Furthermore, very interesting topotactical relations are described for the metal-ceramic interface of the graded zone. Various techniques of structural analysis (X-ray diffraction, scanning electron microscopy, optical microscopy) and simple thermodynamic calculations allow a new interpretation to be given of the bonding between the metal and ceramic components. The cohesion of graded metal-ceramic coatings is predicted to be higher than that of ceramic coatings with a metallic bond layer. The results are illustrated by a NiCr-ZrO{sub 2}(MgO) graded coating. (orig.).

  7. Residual stresses determination in textured substrates for plasma sprayed coatings

    Science.gov (United States)

    Capek, J.; Pala, Z.; Kovarik, O.

    2015-04-01

    In this contribution, we have striven to respond to the desire of obtaining the residual stress tensor in the both cold-rolled and hot-rolled substrates designated for deposition of thermal coatings by plasma spraying. Residual stresses play an important role in the coating adhesion to the substrate and, as such, it is a good practice to analyse them. Prior to spraying, the substrate is often being grit blasted. Residual stresses and texture were quantitatively assessed in both virgin and grit blasted sample employing three attitudes. Firstly without taking preferred orientation into account, secondly from measurements of interplanar lattice spacings of planes with high Miller indices using MoKα radiation. And eventually, by calculating anisotropic elastic constants as a weighted average between single-crystal and X-ray elastic constants with weighting being done according to the amount of textured and isotropic material in the irradiated volume. In the ensuing verification analyses, it was established that the latter approach is suitable for materials with either very strong or very weak presence of texture.

  8. Monitoring and Improving the Reliability of Plasma Spray Processes

    Science.gov (United States)

    Mauer, Georg; Rauwald, Karl-Heinz; Mücke, Robert; Vaßen, Robert

    2017-06-01

    Monitoring and improving of process reliability are prevalent issues in thermal spray technology. They are intended to accomplish specific quality characteristics by controlling the process. For this, implicit approaches are in demand to rapidly conclude on relevant coating properties, i.e., they are not directly measured, but it is assumed that the monitored variables are in fact suggestive for them. Such monitoring can be performed in situ (during the running process) instead of measuring coating characteristics explicitly (directly) and ex situ (after the process). Implicit approaches can be based on extrinsic variables (set from outside) as well as on intrinsic parameters (internal, not directly adjustable) having specific advantages and disadvantages, each. In this work, the effects of atmospheric plasma spray process variables are systemized in process schemes. On this basis, different approaches to contribute to improved process reliability are described and assessed paying particular attention to in-flight particle diagnostics. Finally, a new test applying spray bead analysis is introduced and first results are presented.

  9. Young's Moduli of Cold and Vacuum Plasma Sprayed Metallic Coatings

    Science.gov (United States)

    Raj, S. V.; Pawlik, R.; Loewenthal, W.

    2009-01-01

    Monolithic metallic copper alloy and NiCrAlY coatings were fabricated by either the cold spray (CS) or the vacuum plasma spray (VPS) deposition processes. Dynamic elastic modulus property measurements were conducted on these monolithic coating specimens between 300 K and 1273 K using the impulse excitation technique. The Young's moduli decreased almost linearly with increasing temperature at all temperatures except in the case of the CS Cu-23%Cr-5%Al and VPS NiCrAlY, where deviations from linearity were observed above a critical temperature. It was observed that the Young's moduli for VPS Cu-8%Cr were larger than literature data compiled for Cu. The addition of 1%Al to Cu- 8%Cr significantly increased its Young's modulus by 12 to 17% presumably due to a solid solution effect. Comparisons of the Young s moduli data between two different measurements on the same CS Cu- 23%Cr-5%Al specimen revealed that the values measured in the first run were about 10% higher than those in the second run. It is suggested that this observation is due to annealing of the initial cold work microstructure resulting form the cold spray deposition process.

  10. Recent developments in plasma spray processes for applications in energy technology

    Science.gov (United States)

    Mauer, G.; Jarligo, M. O.; Marcano, D.; Rezanka, S.; Zhou, D.; Vaßen, R.

    2017-03-01

    This work focuses on recent developments of plasma spray processes with respect to specific demands in energy technology. High Velocity Atmospheric Plasma Spraying (HV-APS) is a novel variant of plasma spraying devoted to materials which are prone to oxidation or decomposition. It is shown how this process can be used for metallic bondcoats in thermal barrier coating systems. Furthermore, Suspension Plasma Spraying (SPS) is a new method to process submicron-sized feedstock powders which are not sufficiently flowable to feed them in dry state. SPS is presently promoted by the development of novel torch concepts with axial feedstock injection. An example for a columnar structured double layer thermal barrier coating is given. Finally, Plasma Spray-Physical Vapor Deposition (PS-PVD) is a novel technology operating in controlled atmosphere at low pressure and high plasma power. At such condition, vaporization even of high-melting oxide ceramics is possible enabling the formation of columnar structured, strain tolerant coatings with low thermal conductivity. Applying different conditions, the deposition is still dominated by liquid splats. Such process is termed Low Pressure Plasma Spraying-Thin Film (LPPS-TF). Two examples of applications are gas-tight and highly ionic and electronic conductive electrolyte and membrane layers which were deposited on porous metallic substrates.

  11. Plasma sprayed rutile titania-nanosilver antibacterial coatings

    Science.gov (United States)

    Gao, Jinjin; Zhao, Chengjian; Zhou, Jingfang; Li, Chunxia; Shao, Yiran; Shi, Chao; Zhu, Yingchun

    2015-11-01

    Rutile titania (TiO2) coatings have superior mechanical properties and excellent stability that make them preferential candidates for various applications. In order to prevent infection arising from bacteria, significant efforts have been focused on antibacterial TiO2 coatings. In the study, titania-nanosilver (TiO2/Ag) coatings with five different kinds of weight percentages of silver nanoparticles (AgNPs) were prepared by plasma spray. The feedstock powders, which had a composition of rutile TiO2 powders containing 1-10,000 ppm AgNPs, were double sintered and deposited on stainless steel substrates with optimized spraying parameters. X-Ray diffraction and scanning electron microscopy were used to analysize the phase composition and surface morphology of TiO2/Ag powders and coatings. Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus) were employed to examine the antibacterial activity of the as-prepared coatings by bacterial counting method. The results showed that silver existed homogeneously in the TiO2/Ag coatings and no crystalline changed happened in the TiO2 structure. The reduction ratios on the TiO2/Ag coatings with 10 ppm AgNPs were as high as 94.8% and 95.6% for E. coli and S. aureus, respectively, and the TiO2/Ag coatings with 100-1000 ppm AgNPs exhibited 100% bactericidal activity against E. coli and S. aureus, which indicated the TiO2/Ag coatings with more than 10 ppm AgNPs had strong antibacterial activity. Moreover, the main factors influencing the antibacterial properties of TiO2/Ag coatings were discussed with grain size and the content of silver as well as the microstructure of the coatings.

  12. Electrochemical Evaluation of Thin-Film Li-Si Anodes Prepared by Plasma Spraying

    Energy Technology Data Exchange (ETDEWEB)

    GUIDOTTI,RONALD A.; REINHARDT,FREDERICK W.; SCHARRER,GREGORY L.

    1999-09-08

    Thin-film electrodes of a plasma-sprayed Li-Si alloy were evaluated for use as anodes in high-temperature thermally activated (thermal) batteries. These anodes were prepared using 44% Li/56% Si (w/w) material as feed material in a special plasma-spray apparatus under helium or hydrogen, to protect this air- and moisture-sensitive material during deposition. Anodes were tested in single cells using conventional pressed-powder separators and lithiated pyrite cathodes at temperatures of 400 to 550 C at several different current densities. A limited number of 5-cell battery tests were also conducted. The data for the plasma-sprayed anodes was compared to that for conventional pressed-powder anodes. The performance of the plasma-sprayed anodes was inferior to that of conventional pressed-powder anodes, in that the cell emfs were lower (due to the lack of formation of the desired alloy phases) and the small porosity of these materials severely limited their rate capability. Consequently, plasma-sprayed Li-Si anodes would not be practical for use in thermal batteries.

  13. Mullite Precursor Gels and as Binder in Corundum-mullite Refractory

    Institute of Scientific and Technical Information of China (English)

    WU Xingrong; LI Liaosha; DONG Yuanchi

    2004-01-01

    Boehmite sol is synthesized via sol-gel process using als,then adding silica sol into boehmite sol to prepare mullite precursor gels. XRD studies are performed to characterize the gels.it is found that the gel can be transformed into mullite when calcined at 1100℃ and completed at 1300℃.Corundum-mullite firebricks with different additions of the mullite precursor gel are made by mixing,semi-dry pressing and then sintering at 1520℃.Apparent porosity,bulk density,flexural strength and thermal shock resistance are measured.Results show that the mullite gel can improve densification and strength of corundum-mullite firebricks,especially enhance the thermal shock resistance.SEM micrographs show that the gel added can be formed into needlelike and elongated mullite in the matrix,whose micromorphology can enhance the strength and thermal shock resistance of the samples.

  14. Oxidation Control of Atmospheric Plasma Sprayed FeAl Intermetallic Coatings Using Dry-Ice Blasting

    Science.gov (United States)

    Song, Bo; Dong, Shujuan; Coddet, Pierre; Hansz, Bernard; Grosdidier, Thierry; Liao, Hanlin; Coddet, Christian

    2013-03-01

    The performance of atmospheric plasma sprayed FeAl coatings has been remarkably limited because of oxidation and phase transformation during the high-temperature process of preparation. In the present work, FeAl intermetallic coatings were prepared by atmospheric plasma spraying combined with dry-ice blasting. The microstructure, oxidation, porosity, and surface roughness of FeAl intermetallic coatings were investigated. The results show that a denser FeAl coating with a lower content of oxide and lower degree of phase transformation can be achieved because of the cryogenic, the cleaning, and the mechanical effects of dry-ice blasting. The surface roughness value decreased, and the adhesive strength of FeAl coating increased after the application of dry-ice blasting during the atmospheric plasma spraying process. Moreover, the microhardness of the FeAl coating increased by 72%, due to the lower porosity and higher dislocation density.

  15. Research on the Plasma Spray Process Applying the Finite Element Method

    Directory of Open Access Journals (Sweden)

    Raimonda Lukauskaitė

    2015-03-01

    Full Text Available The article investigates the physical processes of plasma spraying. The application of the finite element method has assisted in establishing the distribution of the voltage of the plasma arc and current density in the plasma stream during numerical simulation. With reference to the results of experimental data, the real location of an anode spot of the electric arc in the plasma spray process has been evaluated. The paper has calculated the values of electromagnetic Lorentz forces and established their influence on plasma flow. With the help of the two-layer model for the semi-molten nickel particle, contact between the particle and substrate during plasma spraying has been simulated.

  16. Bioactive Glass-Ceramic Coatings Synthesized by the Liquid Precursor Plasma Spraying Process

    Science.gov (United States)

    Xiao, Yanfeng; Song, Lei; Liu, Xiaoguang; Huang, Yi; Huang, Tao; Chen, Jiyong; Wu, Yao; Wu, Fang

    2011-03-01

    In this study, the liquid precursor plasma spraying process was used to manufacture P2O5-Na2O-CaO-SiO2 bioactive glass-ceramic coatings (BGCCs), where sol and suspension were used as feedstocks for plasma spraying. The effect of precursor and spray parameters on the formation and crystallinity of BGCCs was systematically studied. The results indicated that coatings with higher crystallinity were obtained using the sol precursor, while nanostructured coatings predominantly consisting of amorphous phase were synthesized using the suspension precursor. For coatings manufactured from suspension, the fraction of the amorphous phase increased with the increase in plasma power and the decrease in liquid precursor feed rate. The coatings synthesized from the suspension plasma spray process also showed a good in vitro bioactivity, as suggested by the fast apatite formation when soaking into SBF.

  17. Preparation and Characterization of Plasma-Sprayed Ultrafine Chromium Oxide Coatings

    Institute of Scientific and Technical Information of China (English)

    LIN Feng; JIANG Xianliang; YU Yueguang; ZENG Keli; REN Xianjing; LI Zhenduo

    2007-01-01

    Ultrafine chromium oxide coatings were prepared by plasma spraying with ultrafine feedstock. Processing parameters of plasma spraying were optimized. Optical microscope (OM) was used to observe the microstructure of the ultrafine chromium oxide coatings. Scanning electron microscopy (SEM) was used to observe the morphology and particle size of ultrafine powder feedstock as well as to examine the microstructure of the chromium oxide coating. In addition, hardness and bonding strength of the ultrafine chromium oxide coatings were measured.The results showed that the optimized plasma spraying parameters were suitable for ultrafine chromium oxide coating and the properties and microstructure of the optimized ultrafine chromium oxide coating were superior compared to conventional chromium oxide wear resistant coatings.

  18. Characterisation of the TiO2 coatings deposited by plasma spraying

    Science.gov (United States)

    Benea, M. L.; Benea, L. P.

    2016-02-01

    Plasma spraying of materials such as ceramics and non-metals, which have high melting points, has become a well-established commercial process. Such coatings are increasingly used in aerospace, automobile, textile, medical, printing and electrical industries to impart proprieties such as corrosion resistance, thermal resistance, wear resistance, etc. One of the most important characteristics of thermal barrier coatings is the ability to undergo fast temperature changes without failing, the so called thermal shock resistance. The formation of residual stresses in plasma sprayed ceramic and metallic coatings is a very complex process. Several factors, such as substrate material, substrate thickness, physical properties of both the substrate and the coating material, deposition rate, relative velocity of the plasma torch, etc. determine the final residual stress state of the coating at room temperature. Our objective is to characterize the titanium oxide and aluminium oxide coatings deposited by plasma spraying in structural terms, the resistance to thermal shock and residual stresses.

  19. Wear and corrosion resistance of laser remelted and plasma sprayed Ni and Cr coatings on copper

    Institute of Scientific and Technical Information of China (English)

    梁工英; 黄俊达; 安耿

    2004-01-01

    Nickel and chromium coatings were produced on the copper sheet using plasma spraying and laser remelting. The sliding wear test was achieved on a block-on-ring tester and the corrosion test was carried out in an acidic atmosphere. The corrosive behaviors of both coatings and original copper samples were investigated by using an impedance comparison method. The experimental results show that the nickel and chromium coatings display better wear resistance and corrosion resistance relative to the original pure copper sample. The wear resistance of the coatings is 8 - 12 times as large as original samples, and the wear resistance of laser remelted samples is better than that of plasma sprayed ones. The corrosion resistance of laser remelted nickel and chromium samples is better than that of plasma sprayed samples respectively. The corrosion rate of chromium coatings is less than that of nickel coatings, and the laser remelted Cr coating exhibits the least corrosion rate.

  20. Wear resistance of laser cladding and plasma spray welding layer on stainless steel surface

    Institute of Scientific and Technical Information of China (English)

    Xinlin Wang(王新林); Shihong Shi(石世宏); Qiguang Zheng(郑启光)

    2004-01-01

    The effect of coatings, which are formed with laser cladding and plasma spray welding on 1Cr18Ni9Ti base metal, on wear resistance is studied, A 5-kW transverse flowing CO2 laser is used for cladding Co base alloy powder pre-placed on the substrate. Comparing with the plasma spray coatings, the spoiled rate of products with laser clad layers was lower and the rate of finished products was higher. Their microstructure is extremely fine. They have close texture and small size grain. Their dilution resulting from the compositions of the base metal and thermal effect on base metal are less. The hardness, toughness,and strength of the laser cladding layers are higher. Wear tests show that the laser layers have higher properties of anti-friction, anti-scour and high-temperature sliding strike. The wear resistance of laser clad layers are about one time higher than that of plasma spray welding layer.

  1. Research on fabricating Fe base amorphous alloy by bar plasma spraying

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Since amorphous alloys have wider application, they can not be fabricated using the conventional cooling velocity. The bar material plasma spraying is adopted to fabricate Fe base amorphous alloy in this investigation. The crystallization degree, microstructure, micro-hardness, composition, crystallization temperature of the amorphous alloy and the flying rules of the atomized particles in the process of the plasma spray are tested. The results show that the alloy prepared has the high amorphous degree and homogeneous microstructure, micro-hardness and the crystallization temperature can reach 1187HV and 531℃ respectively. The atomization is very well during the process of plasma spraying; and there is high thermal gradient, the cooling velocity reaches 6.07×107K/s.

  2. Determination of elastic modulus and residual stress of plasma-sprayed tungsten coating on steel substrate

    Energy Technology Data Exchange (ETDEWEB)

    You, J.H. [Max-Planck-Institut fuer Plasmaphysik, EURATOM Association, Boltzmann Street 2, 85748 Garching (Germany)]. E-mail: jeong-ha.you@ipp.mpg.de; Hoeschen, T. [Max-Planck-Institut fuer Plasmaphysik, EURATOM Association, Boltzmann Street 2, 85748 Garching (Germany); Lindig, S. [Max-Planck-Institut fuer Plasmaphysik, EURATOM Association, Boltzmann Street 2, 85748 Garching (Germany)

    2006-01-01

    Plasma-sprayed tungsten, which is a candidate material for the first wall armour, shows a porous, heterogeneous microstructure. Due to its characteristic morphology, the properties are significantly different from those of its dense bulk material. Measurements of the elastic modulus of this coating have not been reported in the literature. In this work Young's modulus of highly porous plasma-sprayed tungsten coatings deposited on steel (F82H) substrates was measured. For the fabrication of the coating system the vacuum plasma-spray process was applied. Measurements were performed by means of three-point and four-point bending tests. The obtained modulus values ranged from 53 to 57 GPa. These values could be confirmed by the test result of a detached coating strip, which was 54 GPa. The applied methods produced consistent results regardless of testing configurations and specimen sizes. The errors were less than 1%. Residual stress of the coating was also estimated.

  3. Determination of elastic modulus and residual stress of plasma-sprayed tungsten coating on steel substrate

    Science.gov (United States)

    You, J. H.; Höschen, T.; Lindig, S.

    2006-01-01

    Plasma-sprayed tungsten, which is a candidate material for the first wall armour, shows a porous, heterogeneous microstructure. Due to its characteristic morphology, the properties are significantly different from those of its dense bulk material. Measurements of the elastic modulus of this coating have not been reported in the literature. In this work Young's modulus of highly porous plasma-sprayed tungsten coatings deposited on steel (F82H) substrates was measured. For the fabrication of the coating system the vacuum plasma-spray process was applied. Measurements were performed by means of three-point and four-point bending tests. The obtained modulus values ranged from 53 to 57 GPa. These values could be confirmed by the test result of a detached coating strip, which was 54 GPa. The applied methods produced consistent results regardless of testing configurations and specimen sizes. The errors were less than 1%. Residual stress of the coating was also estimated.

  4. Chemical vapor deposition of mullite coatings

    Science.gov (United States)

    Sarin, Vinod; Mulpuri, Rao

    1998-01-01

    This invention is directed to the creation of crystalline mullite coatings having uniform microstructure by chemical vapor deposition (CVD). The process comprises the steps of establishing a flow of reactants which will yield mullite in a CVD reactor, and depositing a crystalline coating from the reactant flow. The process will yield crystalline coatings which are dense and of uniform thickness.

  5. Direct morphological comparison of vacuum plasma sprayed and detonation gun sprayed hydroxyapatite coatings for orthopaedic applications.

    Science.gov (United States)

    Gledhill, H C; Turner, I G; Doyle, C

    1999-02-01

    Hydroxyapatite coatings on titanium substrates were produced using two thermal spray techniques vacuum plasma spraying and detonation gun spraying. X-ray diffraction was used to compare crystallinity and residual stresses in the coatings. Porosity was measured using optical microscopy in conjunction with an image analysis system. Scanning electron microscopy and surface roughness measurements were used to characterise the surface morphologies of the coatings. The vacuum plasma sprayed coatings were found to have a lower residual stress, a higher crystallinity and a higher level of porosity than the detonation gun coatings. It is concluded that consideration needs to be given to the significance of such variations within the clinical context.

  6. Atmosphere corrosion behavior of plasma sprayed and laser remelted coatings on copper

    Institute of Scientific and Technical Information of China (English)

    Gongying Liang; T. T. Wong; Geng An; J. M. K. MacAlpine

    2006-01-01

    Nickel and chromium coatings were produced using plasma spraying and laser remelting on the copper sheet. The corrosion test was carried out in an acidic atmosphere, and the corrosive behaviors of both coatings and original copper samples were investigated by using an impedance comparison method. Experimental results show that nickel and chromium coatings display better corrosion resistance properties relative to the original pure copper sample. The corrosion rate of chromium coating is less than that of nickel coating, and corrosion resistances of laser remelted nickel and chromium samples are better thanthose of plasma sprayed samples. The corrosion deposit film of copper is loose compared with nickel and chromium.

  7. Fabrication and characterization of highly luminescent Er3+:Al2O3 thin films with optimized growth parameters

    Science.gov (United States)

    Nayar, Priyanka; Zhu, Xue-Yi; Yang, Fuyi; Lu, Minghui; Lakshminarayana, G.; Liu, Xiao Ping; Chen, Yan-Feng; Kityk, I. V.

    2016-10-01

    Erbium doped amorphous alumina thin films were fabricated using Co-sputtering technique in various depositions runs with varying parameters for optimizing the deposition parameters to obtain the films with best optical performance. The main subject of investigation includes the effects of change in various deposition parameters such as substrate heating, radio frequency (RF) power and oxygen pressure inside the chamber while deposition. High quality as-deposited films with various Er concentrations and low carbon content have been confirmed by XPS. Substrate heating ∼500 °C was found to be very effective in getting highly dense films with high refractive index of 1.70 at 1530-1570 nm emission band. The Er3+-doped films showed very intense near-infrared luminescence peak at 1550 nm even without any post-deposition annealing treatment.

  8. Spark plasma sintering and mechanical properties of $ZrO_{2} (Y_{2}O_{3})-Al_{2}O_{3}$ composites

    CERN Document Server

    Jin Sheng H; Dalla Torre, S; Miyamoto, H; Miyamoto, K

    2000-01-01

    Spark plasma sintering (SPS) was conducted on nanocrystalline ZrO/sub 2/(Y/sub 2/O/sub 3/)-20 mol% Al/sub 2/O/sub 3/ powder at a heat rate of 600 degrees C/min with a short holding time. Full density was obtained at sintering temperatures >1300 degrees C. Considerable grain growth occurred relative to the initial powder particles, but smaller grain size and higher density can be obtained as compared to hot-pressing. High flexural strength and fracture toughness were also achieved for the SPS-resulted composite. (8 refs).

  9. Microstructure of the Al2O3/Al2O3 Joint Brazed with Cu-Zn-Ti Filler Metal

    Institute of Scientific and Technical Information of China (English)

    Hongyuan FANG; Jianguo YANG; Xiuyu YU

    2001-01-01

    Microstructure and interface reactions of Al2O3 joints brazed by Cu-Zn-Ti alloy were studied by using SEM, EDS and XRD. The effects of brazing temperature and Ti content on interfacial reactions and microstructure were investigated, and the action of adding Zn into brazing alloy was also studied. TiO, Ti3Al and CuTi were formed at the interface of ceramics and the filler metal, while CuTi, Cu3Ti and α-Cu were found in the brazing. The thickness of the reaction layer increased with increasing of brazing temperature, under the same brazing process, the thickness increased with the Ti content.

  10. Concentrated aqueous Si3N4 -Y2O3 -Al2O3 slips stabalized with tetramethylammonium hydroxide

    Directory of Open Access Journals (Sweden)

    Albano M. P.

    1999-01-01

    Full Text Available In order to obtain well dispersed concentrated aqueous Si3N4 slips for slip casting, the influence of pH and sintering aid powders (Y2O3 and Al2O3 on the viscosity and on the amount of tetramethylammonium ions adsorbed were determined. 35 vol% aqueous Si3N4 and Si3N4-6wt%Y2O3-4wt% Al2O3 slips were prepared in an attrition mill. Tetramethylammonium hydroxide was added to adjust the pH values in a range of 9.7 to 12.3. The viscosity of Si3N4 slips and the amount of [(CH34N]+ ions in solution increased with increasing pH. These counterions contributed mainly to increase the ionic strength of the solution with increasing the slip viscosity. The sintering aid powders had a positive effect on the dispersion of the Si3N4 powder at pH 10.3-12.3 since low viscosity values could be obtained. This was attributed to the lower concentration of counterions in solution.

  11. Fatigue testing of plasma-sprayed thermal barrier coatings, volume 2

    Science.gov (United States)

    Cruse, T. A.; Nagy, A.; Popelar, C. F.

    1990-01-01

    A plasma sprayed thermal barrier coating for diesel engines were fatigue tested. Candidate thermal barrier coating materials were fatigue screened and a data base was generated for the selected candidate material. Specimen configurations are given for the bend fatigue tests, along with test setup, specimen preparation, test matrix and procedure, and data analysis.

  12. Fatigue testing of plasma-sprayed thermal barrier coatings, Volume 2. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Cruse, T.A.; Nagy, A.; Popelar, C.F.

    1990-07-01

    A plasma sprayed thermal barrier coating for diesel engines were fatigue tested. Candidate thermal barrier coating materials were fatigue screened and a data base was generated for the selected candidate material. Specimen configurations are given for the bend fatigue tests, along with test setup, specimen preparation, test matrix and procedure, and data analysis.

  13. Structure and property evaluation of a vacuum plasma sprayed nanostructured tungsten-hafnium carbide bulk composite

    NARCIS (Netherlands)

    Rea, K. E.; Viswanathan, V.; Kruize, A.; De Hosson, J. Th. M.; O'Dell, S.; McKechnie, T.; Rajagopalan, S.; Vaidyanathan, R.; Seal, S.; O’Dell, S.

    2008-01-01

    Vacuum plasma spray (VPS) forming of tungsten-based metal matrix nanocomposites (MMCs) has shown to be a cost effective and time saving method for the formation of bulk monolithic nanostructured then no-mechanical components. Spray drying of powder feedstock appears to have a significant effect on

  14. Preparation and properties of HA coating hydrothermally synthesized from plasma sprayed CaHPO4 coating

    Institute of Scientific and Technical Information of China (English)

    FU Tao; HAN Yong; ZHANG Yu-mei; XU Ke-wei

    2001-01-01

    @@ INTRODUCTION Hydroxyapatite (HA) biocoatings can form osseointegration at a shorter time than metallic implants, and plasma sprayed (PS) HA coating has received the widest studies and is now used clinically. However, due to the high temperature of plasma flame, soluble impurity phases and amorphous calcium phosphate were contained which declined the bonding strength of the coating, and spoiled the excellent biological properties of HA.

  15. Deformation Behavior of Nanostructured Ceramic Coatings Deposited by Thermal Plasma Spray

    Institute of Scientific and Technical Information of China (English)

    Xianliang JIANG; Eric Jordan; Leon Shaw; Maurice Gell

    2004-01-01

    Al2O3-13 wt pct TiO2 coating deposited by direct current plasma spray consists of nanostructured region and microlamellae. Bend test shows that the ceramic coating can sustain some deformation without sudden failure. The deformation is achieved through the movement of nano-particles in the nanostructured region under tensile stress.

  16. A new application field of plasma spraying technique to environmental depollution

    Institute of Scientific and Technical Information of China (English)

    YE Fu-xing; A.Ohmori

    2004-01-01

    To expand the application of plasma spraying technique, TiO2 coatings were prepared using agglomerated anatase TiO2 powder to solve the environmental problems. The composition and photocatalytic activity of plasma sprayed TiO2 coatings were investigated systematically. The content of anatase TiO2 in the sprayed coatings was approximate to 7%- 15%, which was influenced by the melting state of TiO2 powder in plasma spraying process. The surface of sprayed coating was very rough and the arithmetical mean deviation of the surface profiles (Ra) was in the range of 5.7 - 8.8 μm. Under lower arc current, the surface of the coating became rougher. The anatase to rutile phase transformation temperature of agglomerated anatase TiO2 powder was approximate to 1 173 K. The TiO2 coating sprayed under the arc current of 400 A had good photocatalytic activity for the relative high content of anatase phase in it. It is concluded that the application of plasma spraying technique to environmental field has been developed.

  17. Modeling Plasma-Particle Interaction in Multi-Arc Plasma Spraying

    Science.gov (United States)

    Bobzin, K.; Öte, M.

    2017-01-01

    The properties of plasma-sprayed coatings are controlled by the heat, momentum, and mass transfer between individual particles and the plasma jet. The particle behavior in conventional single-arc plasma spraying has been the subject of intensive numerical research, whereas multi-arc plasma spraying has not yet received the same attention. We propose herein a numerical model to serve as a scientific tool to investigate particle behavior in multi-arc plasma spraying. In the Lagrangian description of particles in the model, the mathematical formulations describing the heat, momentum, and mass transfer are of great importance for good predictive power, so such formulations proposed by different authors were compared critically, revealing that different mathematical formulations lead to significantly different results. The accuracy of the different formulations was evaluated based on theoretical considerations, and those found to be more accurate were implemented in the final model. Furthermore, a mathematical formulation is proposed to enable simplified calculation of partial particle melting and resolidification.

  18. THE POTENTIAL VALUE OF PHOTOTHERMAL IMAGING FOR THE TESTING OF PLASMA SPRAYED COATINGS

    OpenAIRE

    Almond, D.; Patel, P; Reiter, H.

    1983-01-01

    Measurements are presented which show that the photothermal technique may be used to evaluate plasma sprayed coatings. A photothermal image of a coating adhesion defect is shown and changes in photothermal signal with coating thickness are demonstrated. These measurements are compared directly with ultrasonic measurements of the same sample.

  19. Interfacial characteristics of mullite fiber/BN coating/mullite matrix composites

    Energy Technology Data Exchange (ETDEWEB)

    Chawla, K.K.; Xu, Z.R.; Ha, J.S. [New Mexico Tech, Socorro, NM (United States)] [and others

    1994-12-31

    The interface in mullite fiber Nextel 480/mullite matrix was engineered by using a thick BN (1 {mu}m) coating on mullite fibers, such that deformation mechanisms conducive to toughness enhancement could be brought to play. Significant improvements in the mechanical properties of these mullite fiber/mullite matrix composites could be achieved by incorporation of BN interfacial coating and by using a colloidal processing route to make dense mullite matrix. An interfacial testing system with a flat-bottomed, diamond indenter was used to obtain the interface characteristics. Using a progressive debonding of the interface model, it was determined that the average interfacial frictional sliding shear stress in this composite was about 50 MPa. Fracture surfaces of these BN coated composites obtained in flexure test showed fiber pullout.

  20. Modeling of evaporation and oxidation phenomena in plasma spraying of metal powders

    Science.gov (United States)

    Zhang, Hanwei

    Plasma spraying of metals in air is usually accompanied by evaporation and oxidation of the sprayed material. Optimization of the spraying process must ensure that the particles are fully molten during their short residence time in the plasma jet and prior to hitting the substrate, but not overheated to minimize evaporation losses. In atmospheric plasma spraying (ASP), it is also clearly desirable to be able to control the extent of oxide formation. The objective of this work to develop an overall mathematical model of the oxidization and volatilization phenomena involved in the plasma-spraying of metallic particles in air atmosphere. Four models were developed to simulate the following aspects of the atmospheric plasma spraying (APS) process: (a) the particle trajectories and the velocity and temperature profiles in an Ar-H 2 plasma jet, (b) the heat and mass transfer between particles and plasma jet, (c) the interaction between the evaporation and oxidation phenomena, and (d) the oxidation of liquid metal droplets. The resulting overall model was generated by adapting the computational fluid dynamics code FIDAP and was validated by experimental measurements carried out at the collaborating plasma laboratory of the University of Limoges. The thesis also examined the environmental implications of the oxidization and volatilization phenomena in the plasma spraying of metals. The modeling results showed that the combination of the standard k-s model of turbulence and the Boussinesq eddy-viscosity model provided a more accurate prediction of plasma gas behavior. The estimated NOx generation levels from APS were lower than the U.S.E.P.A. emission standard. Either enhanced evaporation or oxidation can occur on the surface of the metal particles and the relative extent is determined by the process parameters. Comparatively, the particle size has the greatest impact on both evaporation and oxidation. The extent of particle oxidation depends principally on gas

  1. Development of Mullite Substrates and Containers

    Science.gov (United States)

    Sibold, J. D.

    1979-01-01

    The mullite-molten silicon interaction was evaluated through fabrication of a series of bodies made with variations in density, alumina-silica ratio, and glass-crystalline ratio. The materials were tested in a sessile drop technique. None of the variations stood up to extended exposure to molten silicon sufficiently to be recommended as a container material. However, directional solidification experiments suggest that, under proper conditions, contamination of the silicon by mullite containers can be minimized. To improve an already good thermal expansion match between mullite and silicon, compositional variations were studied. Altering of the alumina-silica ratio was determined to give a continuously varying thermal expansion. A standard mullite composition was selected and substrates 40 x 4 x .040 inches were fabricated. Slotted substrates of various configurations and various compositions were also fabricated.

  2. Characterization of NbSi2-Al2O3 nanocomposite coatings prepared with plasma spraying mechanically alloyed powders

    Science.gov (United States)

    Yazdani, Zohreh; Karimzadeh, Fathallah; Abbasi, Mohammad-Hasan; Amini, Abbas

    2015-07-01

    The present study characterized NbSi2-Al2O3 nanocomposite powders plasma-sprayed on Ti-6Al-4V substrates. The powders were agglomerated to obtain suitable particle sizes for spraying. The agglomerated powders were then plasma-sprayed using atmospheric plasma spraying. The structural transformations of the powders along with the morphological and mechanical changes of the coatings were examined by X-ray diffraction, scanning electron microscopy, energy dispersive spectroscopy, transmission electron microscopy, and hardness testing. The results showed that after plasma spraying, the grain size increased, and the lattice strain decreased. However, the grain size of this compound after spraying was still in the nanometer range. The coating was uniform and exhibited good adhesion to the substrate. The microhardness and fracture toughness of the nanocomposite coating were higher than those of a nanostructured NbSi2 coating.

  3. The modulated average structure of mullite.

    Science.gov (United States)

    Birkenstock, Johannes; Petříček, Václav; Pedersen, Bjoern; Schneider, Hartmut; Fischer, Reinhard X

    2015-06-01

    Homogeneous and inclusion-free single crystals of 2:1 mullite (Al(4.8)Si(1.2)O(9.6)) grown by the Czochralski technique were examined by X-ray and neutron diffraction methods. The observed diffuse scattering together with the pattern of satellite reflections confirm previously published data and are thus inherent features of the mullite structure. The ideal composition was closely met as confirmed by microprobe analysis (Al(4.82 (3))Si(1.18 (1))O(9.59 (5))) and by average structure refinements. 8 (5) to 20 (13)% of the available Si was found in the T* position of the tetrahedra triclusters. The strong tendencey for disorder in mullite may be understood from considerations of hypothetical superstructures which would have to be n-fivefold with respect to the three-dimensional average unit cell of 2:1 mullite and n-fourfold in case of 3:2 mullite. In any of these the possible arrangements of the vacancies and of the tetrahedral units would inevitably be unfavorable. Three directions of incommensurate modulations were determined: q1 = [0.3137 (2) 0 ½], q2 = [0 0.4021 (5) 0.1834 (2)] and q3 = [0 0.4009 (5) -0.1834 (2)]. The one-dimensional incommensurately modulated crystal structure associated with q1 was refined for the first time using the superspace approach. The modulation is dominated by harmonic occupational modulations of the atoms in the di- and the triclusters of the tetrahedral units in mullite. The modulation amplitudes are small and the harmonic character implies that the modulated structure still represents an average structure in the overall disordered arrangement of the vacancies and of the tetrahedral structural units. In other words, when projecting the local assemblies at the scale of a few tens of average mullite cells into cells determined by either one of the modulation vectors q1, q2 or q3 a weak average modulation results with slightly varying average occupation factors for the tetrahedral units. As a result, the real

  4. Plasma Spraying of Copper by Hybrid Water-Gas DC Arc Plasma Torch

    Science.gov (United States)

    Kavka, T.; Matějíček, J.; Ctibor, P.; Mašláni, A.; Hrabovský, M.

    2011-06-01

    Water-stabilized DC arc plasma torches offer a good alternative to common plasma sources used for plasma spraying applications. Unique properties of the generated plasma are determined by a specific plasma torch construction. This article is focused on a study of the plasma spraying process performed by a hybrid torch WSP500®-H, which combines two principles of arc stabilization—water vortex and gas flow. Spraying tests with copper powder have been carried out in a wide range of plasma torch parameters. First, analyses of particle in-flight behavior for various spraying conditions were done. After, particles were collected in liquid nitrogen, which enabled analyses of the particle in-flight oxidation. A series of spraying tests were carried out and coatings were analyzed for their microstructure, porosity, oxide content, mechanical, and thermal properties.

  5. The History, Technical Specifications and Efficacy of Plasma Spray Coatings Applied to Joint Replacement Prostheses

    Directory of Open Access Journals (Sweden)

    Andrew McCabe

    2016-12-01

    Full Text Available Thermal plasma sprayed coatings are designed to improve both the biocompatibility and durability of implantable medical devices, and include pure titanium, cobalt/chrome alloy and hydroxyapatite.  Coated joint replacements have now been in continuous clinical use for thirty years and are applied to products manufactured or used in Europe, North America, South America, Africa, Asia and Australasia. Prostheses incorporating such coatings have been successfully implanted into several million of patients worldwide and to date there have been very few reports of any failure of an implant which could be attributed to problems with, or failure of, the coating. This paper summarises the early history of cementless prostheses and subsequent development, specification, validation, regulatory requirements and clinical performance of thermal plasma spray coatings provided by Accentus Medical.

  6. Comprehensive microstructural characterization and predictive property modeling of plasma-sprayed zirconia coatings

    Energy Technology Data Exchange (ETDEWEB)

    Kulkarni, A.; Wang, Z.; Nakamura, T.; Sampath, S.; Goland, A.; Herman, H.; Allen, J.; Ilavsky, J.; Long, G.; Frahm, J.; Steinbrech, R.W

    2003-05-23

    Quantitative microstructure characterization to better understand processing-microstructure-property correlations is of considerable interest in plasma sprayed coating research. This paper quantifies, by means of small-angle neutron scattering (SANS) data, microstructure (porosity, opening dimensions, orientation and morphologies) in plasma sprayed partially-stabilized zirconia (PSZ) coatings, primarily used as thermal barrier coatings. We report on the investigation of the influence of feedstock characteristics on microstructure and establish its influence on the resultant thermal and mechanical properties. The microstructural parameters determined by SANS studies are then assembled into a preliminary model to develop a predictive capability for estimating the properties of these coatings. Thermal conductivity and elastic modulus were predicted using finite element analysis and ultimately compared to experimental values.

  7. PHOTOCATALYTIC PERFORMANCE OF PLASMA SPRAYED TiO2-ZnFe2O4 COATINGS

    Institute of Scientific and Technical Information of China (English)

    Y. Zeng; J.T. Liu; W.J. Qian; J.H. Gao

    2005-01-01

    A novel TiO2-ZnFe2O4 coating is prepared by plasma spraying. The effects of spraying parameters and the composition of powders on the microstructure, surface morphology and photo-absorption of plasma sprayed coatings are studied. The photocatalytic efficiency of the as-sprayed coatings is evaluated through the photo mineralization of methylene blue. It was found that TiO2 coatings can decompose methylene blue under the illumination of ultraviolet rays, and the degrading efficiency is improved with an increase in the content of FeTiO3 in the coatings. However, the presence of large amount of ZnFe2O4 compound will substantially lower the photocatalytic efficiency of the TiO2-ZnFe2O4 coatings for the unfavorable photo-excited electron-hole transfer process.

  8. Morphology, Structure and Biodegradability of Hollow HA Microspheres Obtained by Plasma Spraying

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    The spraying-dried HA (ASD) was employed. ASD was plasma-sprayed onto ice to obtain hollow HA microspheres. The particle size of the sample was determined with a particle size analyzer. The morphology and structure of the samples were measured by scanning electron microscope and X-ray powder diffraction.The in vitro biodegradability of samples was evaluated by immersion tests in Ringer' s solution (RS) and simulated body fluid ( SBF). The samples were immersed respectively in RS and SBF for a period. The Ca2+ ion concentration in the solutions was determined by Atomic Adsorption Spectrum. By plasma spraying hollow HA microspheres were obtained. The hollow microspheres consisted mainly of low crystalline and amorphous HA, and had better biodegradability.

  9. The structure, properties and performance of plasma-sprayed beryllium for fusion applications

    Energy Technology Data Exchange (ETDEWEB)

    Castro, R.G.; Stanek, P.W.; Elliott, K.E. [and others

    1995-09-01

    Plasma-spray technology is under investigation as a method for producing high thermal conductivity beryllium coatings for use in magnetic fusion applications. Recent investigations have focused on optimizing the plasma-spray process for depositing beryllium coatings on damaged beryllium surfaces. Of particular interest has been optimizing the processing parameters to maximize the through-thickness thermal conductivity of the beryllium coatings. Experimental results will be reported on the use of secondary H{sub 2} gas additions to improve the melting of the beryllium powder and transferred-arc cleaning to improve the bonding between the beryllium coatings and the underlying surface. Information will also be presented on thermal fatigue tests which were done on beryllium coated ISX-B beryllium limiter tiles using 10 sec cycle times with 60 sec cooldowns and an International Thermonuclear Experimental Reactor (ITER) relevant divertor heat flux slightly in excess of 5 MW/m{sup 2}.

  10. Fabrication of Nanosized Lanthanum Zirconate Powder and Deposition of Thermal Barrier Coating by Plasma Spray Process

    Science.gov (United States)

    Mishra, S. K.; Jagdeesh, N.; Pathak, L. C.

    2016-07-01

    The present manuscript discusses our findings on fabrication of nanosized lanthanum zirconate powder for thermal barrier coating application and its coating by plasma spray on nickel-based superalloy substrate. Single-phase La2Zr2O7 coating of thickness of the order of 45 µm on the Ni-Cr-Al bond coat coated Ni-based superalloy substrate was deposited by plasma spray process. The layers at the interface did not show spallation and inter diffusion was very less. The microstructure, interface, porosity, and mechanical properties of different layers are investigated. The lanthanum zirconate hardness and modulus were 10.5 and 277 GPa, respectively. The load depth curve for lanthanum zirconate showed good elastic recovery around 74%.

  11. Solid oxide fuel cell electrolytes produced via very low pressure suspension plasma spray and electrophoretic deposition

    OpenAIRE

    Fleetwood, James D

    2014-01-01

    Solid oxide fuel cells (SOFCs) are a promising element of comprehensive energy policies due to their direct mechanism for converting the oxidization of fuel, such as hydrogen, into electrical energy. Both very low pressure plasma spray and electrophoretic deposition allow working with high melting temperature SOFC suspension based feedstock on complex surfaces, such as in non-planar SOFC designs. Dense, thin electrolytes of ideal composition for SOFCs can be fabricated with each of these proc...

  12. Monitoring Delamination of Plasma-Sprayed Thermal Barrier Coatings by Reflectance-Enhanced Luminescence

    Science.gov (United States)

    Eldridge, Jeffrey I.; Bencic, Timothy J.

    2006-01-01

    Highly scattering plasma-sprayed thermal barrier coatings (TBCs) present a challenge for optical diagnostic methods to monitor TBC delamination because scattering attenuates light transmitted through the TBC and usually degrades contrast between attached and delaminated regions of the TBC. This paper presents a new approach where reflectance-enhanced luminescence from a luminescent sublayer incorporated along the bottom of the TBC is used to identify regions of TBC delamination. Because of the higher survival rate of luminescence reflecting off the back surface of a delaminated TBC, the strong scattering exhibited by plasma-sprayed TBCs actually accentuates contrast between attached and delaminated regions by making it more likely that multiple reflections of luminescence off the back surface occur before exiting the top surface of the TBC. A freestanding coating containing sections designed to model an attached or delaminated TBC was prepared by depositing a luminescent Eu-doped or Er-doped yttria-stabilized zirconia (YSZ) luminescent layer below a plasma-sprayed undoped YSZ layer and utilizing a NiCr backing layer to represent an attached substrate. For specimens with a Eu-doped YSZ luminescent sublayer, luminescence intensity maps showed excellent contrast between unbacked and NiCr-backed sections even at a plasma-sprayed overlayer thickness of 300 m. Discernable contrast between unbacked and NiCr-backed sections was not observed for specimens with a Er-doped YSZ luminescent sublayer because luminescence from Er impurities in the undoped YSZ layer overwhelmed luminescence originating form the Er-doped YSZ sublayer.

  13. An Investigation on the Microstructure of Multi-phase Composite Coatings Synthesized by Plasma Spraying Self-reaction Composite Powders

    Institute of Scientific and Technical Information of China (English)

    DONGYan-chun; YANDian-ran; HeJi-ning; LiXiang-zhi; ZHANGJian-xin; NIUEr-wu

    2004-01-01

    Multi-phase self-reacLion composite (denoted as MPc) coatings containing ceramic and metal multi-phases were fabricated by plasma spraying Fe2O3-Al composite powders. This technology successfully combines self-propagating high-temperature synthesis with plasma spraying. The morphology of the composite powders was examined by scanning electron microscope (SEM). The phase composition and microstructure of the composite coating are studied.

  14. Thermal barrier ZrO2 - Y2O3 obtained by plasma spraying method and laser melting

    OpenAIRE

    2006-01-01

    Purpose: The aim of the paper is to determine the influence of laser melting upon the selected physical properties of ZrO2 - Y2O3 ceramic coatings deposited by APS (Air Plasma Spraying) method on super-alloys which function as TBC (Thermal Barriers Coatings).Design/methodology/approach: Laser melting which helps eliminate pores and other structural defects of coatings deposited by plasma spraying method should contribute to the improvement of their density and durability as thermal barriers. ...

  15. An Investigation on the Microstructure of Multi-phase Composite Coatings Synthesized by Plasma Spraying Self-reaction Composite Powders

    Institute of Scientific and Technical Information of China (English)

    DONG Yan-chun; YAN Dian-ran; HE Ji-ning; LI Xiang-zhi; ZHANG Jian-xin; NIU Er-wu

    2004-01-01

    Multi-phase self-reaction composite (denoted as MPc) coatings containing ceramic and metal multi-phases were fabricated by plasma spraying Fe2O3-Al composite powders. This technology successfully combines self-propagating high-temperature synthesis with plasma spraying. The morphology of the composite powders was examined by scanning electron microscope (SEM). The phase composition and microstructure of the composite coating are studied.

  16. Latest Researches Advances of Plasma Spraying: From Splat to Coating Formation

    Science.gov (United States)

    Fauchais, P.; Vardelle, M.; Goutier, S.

    2016-12-01

    The plasma spray process with solid feedstock, mainly ceramics powders, studied since the sixties is now a mature technology. The plasma jet and particle in-flight characterizations are now well established. The use of computer-aided robot trajectory allows spraying on industrial parts with complex geometries. Works about splat formation have shown the importance of: the substrate preheating over the transition temperature to get rid of adsorbates and condensates, substrate chemistry, crystal structure and substrate temperature during the whole coating process. These studies showed that coating properties strongly depend on the splat formation and layering. The first part of this work deals with a summary of conventional plasma spraying key points. The second part presents the current knowledge in plasma spraying with liquid feedstock, technology developed for about two decades with suspensions of particles below micrometers or solutions of precursors that form particles a few micrometers sized through precipitation. Coatings are finely structured and even nanostructured with properties arousing the interest of researchers. However, the technology is by far more complex than the conventional ones. The main conclusions are that models should be developed further, plasma torches and injection setups adapted, and new measuring techniques to reliably characterize these small particles must be designed.

  17. Plasma-spraying synthesis of high-performance photocatalytic TiO2 coatings

    Science.gov (United States)

    Takahashi, Yasuo; Shibata, Yoshitaka; Maeda, Masakatsu; Miyano, Yasuyuki; Murai, Kensuke; Ohmori, Akira

    2014-08-01

    Anatase (A-) TiO2 is a photocatalytic material that can decompose air-pollutants, acetaldehyde, bacteria, and so on. In this study, three kinds of powder (A-TiO2 without HAp, TiO2 + 10mass%HAp, and TiO2+30mass%HAp, where HAp is hydroxyapatite and PBS is polybutylene succinate) were plasma sprayed on biodegradable PBS substrates. HAp powder was mixed with A-TiO2 powder by spray granulation in order to facilitate adsorption of acetaldehyde and bacteria. The crystal structure was almost completely maintained during the plasma spray process. HAp enhanced the decomposition of acetaldehyde and bacteria by promoting adsorption. A 10mass% HAp content was the most effective for decomposing acetaldehyde when plasma preheating of the PBS was not carried out before the plasma spraying. The plasma preheating of PBS increased the yield rate of the spray process and facilitated the decomposition of acetaldehyde by A-TiO2 coatings without HAp. HAp addition improved photocatalytic sterilization when plasma preheating of the PBS was performed.

  18. Latest Researches Advances of Plasma Spraying: From Splat to Coating Formation

    Science.gov (United States)

    Fauchais, P.; Vardelle, M.; Goutier, S.

    2016-08-01

    The plasma spray process with solid feedstock, mainly ceramics powders, studied since the sixties is now a mature technology. The plasma jet and particle in-flight characterizations are now well established. The use of computer-aided robot trajectory allows spraying on industrial parts with complex geometries. Works about splat formation have shown the importance of: the substrate preheating over the transition temperature to get rid of adsorbates and condensates, substrate chemistry, crystal structure and substrate temperature during the whole coating process. These studies showed that coating properties strongly depend on the splat formation and layering. The first part of this work deals with a summary of conventional plasma spraying key points. The second part presents the current knowledge in plasma spraying with liquid feedstock, technology developed for about two decades with suspensions of particles below micrometers or solutions of precursors that form particles a few micrometers sized through precipitation. Coatings are finely structured and even nanostructured with properties arousing the interest of researchers. However, the technology is by far more complex than the conventional ones. The main conclusions are that models should be developed further, plasma torches and injection setups adapted, and new measuring techniques to reliably characterize these small particles must be designed.

  19. D. C. Plasma-Sprayed Coatings of Nanostructured Alumina-Titania-Silica

    Institute of Scientific and Technical Information of China (English)

    蒋显亮; 刘敏

    2002-01-01

    Nanocrystalline powders of w(Al2O3) = 95%, w(TiO2) = 3%, and w(SiO2) = 2%,were reprocessed into agglomerated particles for plasma spraying, by using consecutive steps ofball milling, slurry forming, spray drying, and heat treatment. D. C. plasma was used to spraythe agglomerated nanocrystalline powders, and resultant coatings were deposited on the substrate of stainless steel. Scanning electron microscopy (SEM) was used to examine the morphology of the agglomerated powders and the cross section of the alumina-titania-silica coatings. Exper-imental results show that the agglomerated nanocrystalline particles are spherical, with a size from (10~90)μm. The flow ability of the nanocrystalline powders is greatly improved after the reprocessing. The coatings deposited by the plasma spraying are mainly of nanostructure. Un-like conventional plasma-sprayed coatings, no laminar layer could be found in the nanostructured coatings. Although the nanostructured coatings have a lower microhardness than conventional microstructured coatings, the toughness of the nanostructured ceramic coatings is significantly improved.

  20. Residual stress analysis of the thermal barrier coating system by considering the plasma spraying process

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Myung Jae; Lee, Byung Chai [KAIST, Daejeon (Korea, Republic of); Lim, Jang Gyun; Kim, Moon Ki [Sungkyunkwan University, Suwon (Korea, Republic of)

    2014-06-15

    The residual stress is the key factor causing the reliability problem of thermal barrier coating (TBC). The failure of plasma spray coatings due to residual stresses is a serious and recurring problem of TBC. The difference of thermal expansion coefficient between the substrate and each coating combined with temperature evolution and temperature gradients during deposition process determine the residual stress for the whole TBC system. The magnitudes and distributions of the residual stresses are affected by deposition process and deposition characteristics. Most of FEA (finite element analysis) has been performed under the assumption that the multilayer coating system is stacked at once without considering the deposition process during plasma spraying. In this research, FEA for a coupled heat transfer and elastic-plastic thermal stress was performed to obtain the more detailed and reliable result of residual stress of the TBC system using the element activation/deactivation technique. The residual stress variation from the start of plasma spraying to cooling stage with room temperature was obtained systematically considering the deposition process. It can be used as reference data to improve the performance of TBC. In addition, the relationship between residual stress and coating conditions such as cooling rate and time is also examined thoroughly.

  1. Wear behavior of gas tunnel type plasma sprayed Zr-based metallic glass composite coatings

    Energy Technology Data Exchange (ETDEWEB)

    Yugeswaran, S., E-mail: yugeswaran@gmail.com [Joining and Welding Research Institute, Osaka University, 11-1 Mihogaoka, Ibaraki, Osaka 567-0047 (Japan); Kobayashi, A., E-mail: kobayasi@jwri.osaka-u.ac.jp [Joining and Welding Research Institute, Osaka University, 11-1 Mihogaoka, Ibaraki, Osaka 567-0047 (Japan); Suresh, K., E-mail: ksureshphy@gmail.com [Department of Mechanical and Biomedical Engineering, City University of Hong Kong, Tat Chee Avenue, Kowloon, Hong Kong Special Administrative Region (China); Rao, K.P., E-mail: mekprao@cityu.edu.hk [Department of Mechanical and Biomedical Engineering, City University of Hong Kong, Tat Chee Avenue, Kowloon, Hong Kong Special Administrative Region (China); Subramanian, B., E-mail: subramanianb3@gmail.com [CSIR - Central Electrochemical Research Institute, Karaikudi 630 006 (India)

    2012-09-01

    Highlights: Black-Right-Pointing-Pointer Zr-based metallic glass composite coatings are prepared by gas tunnel plasma torch. Black-Right-Pointing-Pointer Increasing plasma current increases crystallinity amount and hardness of coatings. Black-Right-Pointing-Pointer Coating produced at 300 A plasma current gives minimum sliding wear rate. Black-Right-Pointing-Pointer Coating produced at higher plasma current gives lower erosive wear rate. - Abstract: Gas tunnel type plasma spraying is a prospective method to produce metallic glass composite coatings with high quality due to its noteworthy feature of process controllability. In this study, Zr{sub 55}Cu{sub 30}Al{sub 10}Ni{sub 5} metallic glass composite coatings were produced by gas tunnel type plasma spraying torch under optimum spraying conditions with selected plasma currents. The formation mechanism, sliding, and erosive wear behaviors of the coatings with respect to plasma current was examined. The phase and thermal analyses as well as microstructure of the plasma sprayed coatings produced at different plasma currents were characterized using X-ray diffraction (XRD), differential scanning calorimetry (DSC), scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy (EDX) techniques. The sliding and erosive wear behaviors of the coatings were studied using a pin-on-disc and a specially designed erosive wear tester, respectively. The results showed that an increase in plasma current increased the crystalline content in the metallic glass composite coatings, which enhanced the hardness and wear resistance of the coatings.

  2. The Solution Precursor Plasma Spray (SPPS) Process: A Review with Energy Considerations

    Science.gov (United States)

    Jordan, Eric H.; Jiang, Chen; Gell, Maurice

    2015-10-01

    Solution precursor plasma spray (SPPS) is a coating deposition process that uses conventional plasma spray equipment, and solution precursors, rather than ceramic or metal powders, as starting materials. Because the process is exposed to oxygen at high temperatures, nearly all coatings, to date, are oxide ceramics. In this review, both the advantages and the disadvantages of the SPPS process and some comparisons made to the suspension plasma spray (SPS) process will be discussed. The advantages of the SPPS process include rapid exploration of compositions and fabrication of advanced coatings with unique microstructural features. Examples presented span densities from porous thermal barrier coatings (TBCs) to dense TiO2 coatings. Two TBCs are in an advanced development stage: (1) a low thermal conductivity YSZ TBC and (2) a high-temperature yttrium aluminum garnet TBC. As for disadvantages, there are (1) the additional development work for each new precursor and (2) a lower standoff distance and deposition rate than the APS process, related to the evaporation of the solvent. The SPS process shares the same disadvantages. In developing new coatings, a number of factors should be considered and understood, which would help to shorten future development efforts. Future directions of the SPPS process will also be discussed.

  3. Recent Trends in Newly Developed Plasma-Sprayed and Sintered Coatings for Implant Applications

    Science.gov (United States)

    Bsat, Suzan; Speirs, Andrew; Huang, Xiao

    2016-08-01

    The current paper aims to review recent trends (2011 to 2015) in newly developed plasma-sprayed and sintered coatings for implant applications. Recent developments in plasma-sprayed and sintered coatings have focused on improving biological performance, bacterial growth resistance, and mechanical properties, predominantly of HA and glass ceramics. The majority of these improvements are attributed to the addition of dopants. To improve biological performance, trace elements, such as Zn and Mg, both of which are found in bone, were added to replicate the functions they provide for the skeletal system. Though bacterial growth resistance is traditionally improved by Ag dopant, the addition of new dopants such as CeO2 and Zn were explored as well. Great effort has also been made to improve coating adherence and reduce stresses by minimizing coefficient of thermal expansion mismatch between the coating and substrate through the addition of elements such as Zn and Mg or the inclusion of a buffer layer. For sintering process in particular, there was an emphasis on reducing sintering temperature through modification of 45S5 Bioglass. New plasma spray and sintering technologies aimed at reducing high-temperature exposure are briefly introduced as well. These include microplasma spray and spark plasma sintering.

  4. Liquid Feedstock Plasma Spraying: An Emerging Process for Advanced Thermal Barrier Coatings

    Science.gov (United States)

    Markocsan, Nicolaie; Gupta, Mohit; Joshi, Shrikant; Nylén, Per; Li, Xin-Hai; Wigren, Jan

    2017-08-01

    Liquid feedstock plasma spraying (LFPS) involves deposition of ultrafine droplets of suspensions or solution precursors (typically ranging from nano- to submicron size) and permits production of coatings with unique microstructures that are promising for advanced thermal barrier coating (TBC) applications. This paper reviews the recent progress arising from efforts devoted to development of high-performance TBCs using the LFPS approach. Advancements in both suspension plasma spraying and solution precursor plasma spraying, which constitute the two main variants of LFPS, are presented. Results illustrating the different types of the microstructures that can be realized in LFPS through appropriate process parameter control, model-assisted assessment of influence of coating defects on thermo-mechanical properties and the complex interplay between pore coarsening, sintering and crystallite growth in governing thermal conductivity are summarized. The enhancement in functional performances/lifetime possible in LFPS TBCs with multilayered architectures and by incorporating new pyrochlore chemistries such as gadolinium zirconate, besides the conventional single 8 wt.% yttria-stabilized zirconia insulating ceramic layer, is specifically highlighted.

  5. In vitro antibacterial and osteogenic properties of plasma sprayed silver-containing hydroxyapatite coating

    Institute of Scientific and Technical Information of China (English)

    RUAN HongJiang; FAN CunYi; ZHENG XueBin; ZHANG Yan; CHEN YiKai

    2009-01-01

    The objective of the present investigation was to characterize the antibacterial and osteogenic proper-ties of plasma sprayed silver-containing hydroxyapatite (HA/Ag) coating in vitro. HA/Ag coating was deposited via vacuum plasma spraying. The concentration of silver ions released from HA/Ag coating, the efficacy of the HA/Ag coating against bacterial biofilm development, the effect of the HA/Ag coating on early adhesion and ossification of osteoblast cells in vitro was measured. The silver ion concentra-tion released from the HA/Ag coating was between the minimum inhibitory concentration to bacteria and the cytotoxic concentration. Bacterial biofiim inhibition studies indicated an antibacterial activity on the HA/Ag coating surface when compared with hydroxyapatite (HA) coating alone. Moreover, it was demonstrated that osteoblast cell adhesion and mineralization occurred on the HA/Ag coating surface during the testing period. We conclude that the vacuum plasma sprayed HA/Ag coating possesses good antibacterial capability and osteogenic properties in vitro and represents a promising candidate for coating orthopedic implants.

  6. Ceramic Top Coats of Plasma-Sprayed Thermal Barrier Coatings: Materials, Processes, and Properties

    Science.gov (United States)

    Bakan, Emine; Vaßen, Robert

    2017-08-01

    The ceramic top coat has a major influence on the performance of the thermal barrier coating systems (TBCs). Yttria-partially-stabilized zirconia (YSZ) is the top coat material frequently used, and the major deposition processes of the YSZ top coat are atmospheric plasma spraying and electron beam physical vapor deposition. Recently, also new thermal spray processes such as suspension plasma spraying or plasma spray-physical vapor deposition have been intensively investigated for TBC top coat deposition. These new processes and particularly the different coating microstructures that can be deposited with them will be reviewed in this article. Furthermore, the properties and the intrinsic-extrinsic degradation mechanisms of the YSZ will be discussed. Following the TBC deposition processes and standard YSZ material, alternative ceramic materials such as perovskites and hexaaluminates will be summarized, while properties of pyrochlores with regard to their crystal structure will be discussed more in detail. The merits of the pyrochlores such as good CMAS resistance as well as their weaknesses, e.g., low fracture toughness, processability issues, will be outlined.

  7. D. C. plasma-sprayed coatings of nano-structured alumina-titania-silica

    CERN Document Server

    Jiang Xian Liang

    2002-01-01

    nano-crystalline powders of omega(Al sub 2 O sub 3) = 95%, omega(TiO sub 2) = 3%, and omega(SiO sub 2) = 2%, were reprocessed into agglomerated particles for plasma spraying, by using consecutive steps of ball milling, slurry forming, spray drying, and heat treatment. D.C. plasma was used to spray the agglomerated nano-crystalline powders, and resultant coatings were deposited on the substrate of stainless steel. Scanning electron microscopy (SEM) was used to examine the morphology of the agglomerated powders and the cross section of the alumina-titania-silica coatings. Experimental results show that the agglomerated nano-crystalline particles are spherical, with a size from (10-90) mu m. The flow ability of the nano-crystalline powders is greatly improved after the reprocessing. The coatings deposited by the plasma spraying are mainly of nano-structure. Unlike conventional plasma-sprayed coatings, no laminar layer could be found in the nano-structured coatings. Although the nano-structured coatings have a lo...

  8. Svnthesis and Characterization of Nanoscale Mullite Powder

    Institute of Scientific and Technical Information of China (English)

    ZHAO Huizhong; HU Shoutian; WANG Houzhi; ZHANG Wenjie

    2003-01-01

    Nanoscale mullite powder were synthesized via Solgel-SCFD and middle temperature treatment by using AIP( aluminum-isopropoxde ) and TEOS ( tetraethyl orthosdicate) as starting materials. Both of the binary aerogel of alumina-silica and calcined nanoscale materials were investigated by using TG-DSC (thermogravimetry-differential scanning calorimeter), TEM (transmission electron microscope), XRD ( X-Ray diffractometer ) and specific surface area and porosimetry. TG-DSC indicated the removal of most of the volatiles , i. e. 15.98% up to about 700℃ ,and in the DSC curve, existence of two exothermic peak at about 445℃ and 1015℃ may be due to the crystallization of Si-O-Al-O in diphasic gels and mullitization and a small endothermic peak at about 805℃ indicated the decomposition of structural water molecules. On the colligation of the results of TG- DSC, XRD and TEM , the beginning temperature of mullitization in Al2 O3-SiO2 aerogel system can be confirmed at about 1015℃. XRD results also showed the formation of mullite at the range 1100 ~1200℃. TEM and surface area and porosimetry results showed that the nanosized mullite were calcinated at 1100and 1200℃ exhibited size 30nm and 50nm, specific surface area 138.91m2/g and 95.81m2/g.

  9. Mathematical analysis of thermoelastic characteristics in plasma-sprayed thermal barrier coatings.

    Science.gov (United States)

    Go, Jaegwi; Jungo, Yeon-Gil; Kim, Seokchan; Ali, Md Afsar; Paik, Ungyu

    2012-02-01

    The thermoelastic characteristics of plasma-sprayed thermal barrier coatings (TBCs) have been analyzed using mathematical modeling. Two types of TBC model, cylinder and circular disk which are commercial plasma-sprayed TBCs, subjecting to symmetric temperature distribution to the radial and longitudinal directions, respectively, were taken into consideration. Based on the thermoelastic theories, a second order ordinary differential equation was derived for the cylinder model and a pair of partial differential equations were set up for the circular disk model. The analytic solution was obtained from the ordinary differential equation, while a finite volume method was developed for numerical solutions to the pair of partial differential equations due to the complexity of governing equations. The thermoelastic characteristics of TBC models, such as temperature distributions, displacements, and stresses, were displayed according to the obtained solutions. The rate of heat conduction in the section of the top coat is relatively slow in comparison with the substrate, and no profound difference appears in the temperature distribution between two TBC models. The highest longitudinal tensile stress is expressed at the bond coat of both models, and the substrate is under the compressive stresses to the circumferential direction. While the cylinder expands to the positive longitudinal direction only, the expansion in the circular disk occurs to both the positive and negative longitudinal directions. Relatively large displacement and stresses exhibit in the cylinder as compared with the circular disk. In the circular disk, the stresses to the radial direction undulate at each section, and the displacement profile displays that the width of the circular disk is slightly narrowed. The results demonstrate that the mechanical and thermal properties of the top and bond coats are the crucial factors to be considered in controlling the thermoelastic characteristics of plasma-sprayed

  10. Corrosion performance of atmospheric plasma sprayed alumina coatings on AZ31B magnesium alloy under immersion environment

    Directory of Open Access Journals (Sweden)

    D. Thirumalaikumarasamy

    2014-12-01

    Full Text Available Plasma sprayed ceramic coatings are successfully used in many industrial applications, where high wear and corrosion resistance with thermal insulation are required. The alumina powders were plasma sprayed on AZ31B magnesium alloy with three different plasma spraying parameters. In the present work, the influence of plasma spray parameters on the corrosion behavior of the coatings was investigated. The corrosion behavior of the coated samples was evaluated by immersion corrosion test in 3.5 wt% NaCl solution. Empirical relationship was established to predict the corrosion rate of plasma sprayed alumina coatings by incorporating process parameters. The experiments were conducted based on a three factor, five-level, central composite rotatable design matrix. The developed relationship can be effectively used to predict the corrosion rate of alumina coatings at 95% confidence level. The results indicate that the input power has the greatest influence on corrosion rate, followed by stand-off distance and powder feed rate.

  11. Microstructure and Oxidation Resistance of Laser Remelted Plasma Sprayed Nicraly Coating

    Directory of Open Access Journals (Sweden)

    Niemiec D.

    2016-06-01

    Full Text Available The article presents results of research relating to the impact of laser treatment done to the surface of plasma sprayed coatings NiCrAlY. Analysis consisted microstructure and oxidation resistance of coatings subjected to two different laser melting surfaces. The test were performed at a temperature 1000°C the samples were removed from the furnace after 25, 300, 500, 750 and 1000 hours. The investigations range included analysis of top surface of coatings by XRD characterization oxides formed types and microscopic investigations of coatings morphology

  12. Structure and property evaluation of a vacuum plasma sprayed nanostructured tungsten-hafnium carbide bulk composite

    Energy Technology Data Exchange (ETDEWEB)

    Rea, K.E.; Viswanathan, V.; Kruize, A. [Surface Engineering and Nanotechnology Facility (SNF), University of Central Florida, Eng. 381, 4000 Central Florida Blvd., Orlando, FL 32816 (United States); AMPAC, Department of Mechanical, Materials, and Aerospace Engineering (MMAE), Nanoscience and Technology Center, University of Central Florida, Eng. 381, 4000 Central Florida Blvd., Orlando, FL 32816 (United States); Hosson, J.Th.M. de [Department of Applied Physics, University of Groningen, Nijenborgh 4, NL-9747 AG (Netherlands); O' Dell, S.; McKechnie, T. [Plasma Processes, Inc., 4914 Moores Mill Road, Huntsville, AL 35811 (United States); Rajagopalan, S.; Vaidyanathan, R. [AMPAC, Department of Mechanical, Materials, and Aerospace Engineering (MMAE), Nanoscience and Technology Center, University of Central Florida, Eng. 381, 4000 Central Florida Blvd., Orlando, FL 32816 (United States); Seal, S. [Surface Engineering and Nanotechnology Facility (SNF), University of Central Florida, Eng. 381, 4000 Central Florida Blvd., Orlando, FL 32816 (United States); AMPAC, Department of Mechanical, Materials, and Aerospace Engineering (MMAE), Nanoscience and Technology Center, University of Central Florida, Eng. 381, 4000 Central Florida Blvd., Orlando, FL 32816 (United States)], E-mail: sseal@mail.ucf.edu

    2008-03-25

    Vacuum plasma spray (VPS) forming of tungsten-based metal matrix nanocomposites (MMCs) has shown to be a cost effective and time saving method for the formation of bulk monolithic nanostructured thermo-mechanical components. Spray drying of powder feedstock appears to have a significant effect on the improved mechanical properties of the bulk nanocomposite. The reported elastic modulus of the nanocomposite nearly doubles due to the presence of HfC nano particulates in the W matrix. High resolution transmission electron microscopy (HRTEM) revealed the retention of nanostructures at the select process conditions and is correlated with the enhanced mechanical properties of the nanocomposite.

  13. Plasma-spray synthesis and characterization of ti-based nitride and oxide nanogranules

    Energy Technology Data Exchange (ETDEWEB)

    Antipas, Georgios S.E., E-mail: gantipas@metal.ntua.gr [School of Mining Engineering and Metallurgy, National Technical University of Athens, Athens (Greece)

    2014-09-15

    The synthesis of nanosized Ti-based nanogranules via plasma spraying is reported. The synthesis route involved use of both nitrogen and oxygen gases with varying results. In the case of nitrogen, a mixture of titanium nitrides were produced, yielding both the Ti2N and the sub-stoichiometric TiN0.61 compounds. In the case of oxygen, both the stoichiometric rutile and TiO ceramic phases were indexed. Based on EDS analysis, even fractional oxygen concentrations caused tungsten impurities which originated from the cathode electrode. The method yielded particle mass median sizes of the order of 15nm and the smallest particles detected were 5nm. (author)

  14. Morphology and Phase Compositions of Hydroxyapatite Powder Particles Plasma-sprayed into Water

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Hydroxyapatite powder particles were plasma sprayed into water, their inner structures and phase compositions were studied by using scanning electron microscope(SEM) and X-ray difiractometer. The results show that the molten HA particles have a central hollow morphology and high crystallinity. The hollow morphology was caused by sublimated P2O5 and H2O, which will have an efiect on surface morphology, cohesive and adhesive strength as well as dissolution and degradation of coating. The high crystallinity is attributed to lower cooling speed in water.

  15. The relationship between the microstructure and thermal diffusivity of plasma-sprayed tungsten coatings

    Energy Technology Data Exchange (ETDEWEB)

    Moreau, C. [National Research Council Canada, Boucherville, Quebec (Canada); Boire-Lavigne, S.; Saint-Jacques, R.G. [INRS-Energie et Materiaux, Varennes, Quebec (Canada)

    1994-12-31

    Tungsten and tungsten alloy coatings are candidate materials for plasma facing components of divertor plates in future fusion reactors. In normal operation, the sprayed coatings will be submitted to intense heat fluxes and particle bombardment. This work intends to investigate the relationship between the microstructure of plasma-sprayed tungsten coatings and their thermal diffusivity as determined by the laser flash method. The microstructural investigation was carried out on copper-infiltrated coatings. Such a preparation technique permitted the measurement of the total real contact area between the lamellae within the tungsten coatings. The spraying atmosphere was found to strongly influence the interfacial contact between lamellae and coating thermal diffusivity.

  16. The change of NiCrBSi alloys’ phase composition after plasma spraying

    Directory of Open Access Journals (Sweden)

    A. Dudek

    2008-08-01

    Full Text Available Material for investigations was NiCrBSi powder for components’ coatings which improve their corrosion resistance as well as resistance to friction wear and erosion. Plasma spraying method was used to produce a coating with thickness of 300 μm on low-alloy steel which was then remelted with the base material. Using X-ray quality analysis, phase composition was determined for: NiCrBSi powder, obtained coating and the alloyed surface layer. Crystallinity degree was also calculated for NiCrBSi layer sprayed on the base material.

  17. Physical, mechanical, and tribological properties of quasicrystalline Al-Cu-Fe coatings prepared by plasma spraying

    Science.gov (United States)

    Lepeshev, A. A.; Rozhkova, E. A.; Karpov, I. V.; Ushakov, A. V.; Fedorov, L. Yu.

    2013-12-01

    The physical, mechanical, and tribological properties of quasicrystalline coatings based on the Al65Cu23Fe12 alloy prepared by plasma spraying have been investigated. The specific features of the phase formation due to the competitive interactions of the icosahedral ψ and cubic β phases have been elucidated. A correlation between the microhardness and the content of the icosahedral phase in the coating has been determined. The decisive role of the quasicrystalline phase in the formation of high tribological characteristics of the coatings has been revealed and tested.

  18. THE EFFECT OF LASER GLAZING PROCESS ON MICROSTRUCTURE OF PLASMA SPRAYED THERMAL BARRIER COATINGS

    Directory of Open Access Journals (Sweden)

    Seyid Fehmi DİLTEMİZ

    2011-12-01

    Full Text Available Thermal barrier coatings (TBCs are widely used by aero and land based gas turbines to protect hot section parts from oxidation and reducing component temperature thereby increase life. TBCs aregenerally a combination of multiple layers of coating (usually two with each layer having a specific function [Aktaa et al., 2005]. In this study air plasma sprayed TBCs were deposited on 304 stainlesssteel substrates then ceramic surfaces were glazed using Nd-YAG laser. Both glazed and as-coated samples were subjected to metallographic examination to investigate microstructural changes inglazed ceramic layer. Laser glazing provides a remelting and subsequent solidification of the surface, resulting on new top layer microstructure.

  19. The application of plasma-sprayed ceramic coatings on lift roller in float glass

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    Oxide ceramic was sprayed via high-energy plasma spray using MCrAlY manufactured with special technique as bond coating and oxide ceramic as top coating in this article. Investigation showed that the dense and highly adhesive coating could be obtained with optimized technique. After grinding and polishing, coating roughness was lower than 0. 2μm, which could meet the requirements of lift roller. After one year serv ice, molten Tin could not adhere to the ceramic coating,well it greatly alleviated its corrosion to the roller , kept the surface of oxide ceramic coating smooth and the improve the quality of glass due to the strengthened lift roll.

  20. PREPARATION OF HIGH PURITY MULLITE CERAMICS

    OpenAIRE

    Rodrigo, P.; Boch, P.

    1986-01-01

    Preparation of mullite ceramics by reaction-sintering of alumina silica shows the necessity of favoring densification over mullitisation. Different Al2O3/SiO2 ratios have been studied. The influence of additives, iron oxide and zirconium oxide, has been examined.

  1. Tailoring the heat transfer on the injection moulding cavity by plasma sprayed ceramic coatings

    Science.gov (United States)

    Bobzin, K.; Hopmann, Ch; Öte, M.; Knoch, M. A.; Alkhasli, I.; Dornebusch, H.; Schmitz, M.

    2017-03-01

    Inhomogeneous material shrinkage in injection moulding can cause warpage in thermoplastic components. To minimise the deformations of the injection moulding parts, the heat transfer during the cooling phase can be adjusted according to the local cooling demand on the surface of the mould cavity by means of plasma sprayed coatings with locally variable thermal resistance over the surface of the mould. Thermal resistance is a function of thermal conductivity and thickness of the coatings, where thermal conductivity of thermal barrier coatings can be adjusted by altering the chemical composition and the microstructure, which is depending on the thickness. This work evaluates the application of plasma sprayed coatings with variable thickness as thermal barrier coatings in the mould cavity. The thermal resistance of the coating and thereby the heat transfer from the melt into the mould will be influenced locally by varying the coating thickness over the cavity area according to the local cooling demand. Using the laser flash method, the thermal conduction of coatings with different thicknesses will be determined. On the basis of the experimentally determined thermal conduction, the effect of the coatings on the temperature field of the mould cavity will be numerically calculated and the required thickness distribution of the coating for an optimal temperature gradient will be determined.

  2. Plasma-Sprayed Hydroxylapatite-Based Coatings: Chemical, Mechanical, Microstructural, and Biomedical Properties

    Science.gov (United States)

    Heimann, Robert B.

    2016-06-01

    This contribution discusses salient properties and functions of hydroxylapatite (HA)-based plasma-sprayed coatings, including the effect on biomedical efficacy of coating thickness, phase composition and distribution, amorphicity and crystallinity, porosity and surface roughness, cohesion and adhesion, micro- and nano-structured surface morphology, and residual coating stresses. In addition, it will provide details of the thermal alteration that HA particles undergo in the extremely hot plasma jet that leads to dehydroxylated phases such as oxyhydroxylapatite (OHA) and oxyapatite (OA) as well as thermal decomposition products such as tri-(TCP) and tetracalcium phosphates (TTCP), and quenched phases such as amorphous calcium phosphate (ACP). The contribution will further explain the role of ACP during the in vitro interaction of the as-deposited coatings with simulated body fluid resembling the composition of extracellular fluid (ECF) as well as the in vivo responses of coatings to the ECF and the host tissue, respectively. Finally, it will briefly describe performance profiles required to fulfill biological functions of osteoconductive bioceramic coatings designed to improve osseointegration of hip endoprostheses and dental root implants. In large parts, the content of this contribution is a targeted review of work done by the author and his students and coworkers over the last two decades. In addition, it is considered a stepping stone toward a standard operation procedure aimed at depositing plasma-sprayed bioceramic implant coatings with optimum properties.

  3. Better Quality Control: Stochastic Approaches to Optimize Properties and Performance of Plasma-Sprayed Coatings

    Science.gov (United States)

    Heimann, Robert B.

    2010-06-01

    Statistical design of experiment (SDE) methodology applied to design and performance testing of plasma-sprayed coatings follows an evolutionary path, usually starting with classic multiparameter screening designs (Plackett-Burman), and progressing through factorial (Taguchi) to limited response surface designs (Box-Behnken). Modern designs of higher dimensionality, such as central composite and D-optimal designs, will provide results with higher predictive power. Complex theoretical models relying on evolutionary algorithms, and application of artificial neuronal networks (ANNs) and fuzzy logic control (FLC) allow estimating the behavior of the complex plasma spray environment through validation either by key experiments or first-principle calculations. In this review, paper general principles of SDE will be discussed and examples be given that underscore the different powers of prediction of individual statistical designs. Basic rules of ANN and FLC will be briefly touched on, and their potential for increased reliability of coating performance through stringent quality control measures assessed. Salient features will be reviewed of studies performed to optimize thermal coating properties and processes reported in the pertinent literature between 2000 and the present.

  4. Isothermal Oxidation Behavior of Supersonic Atmospheric Plasma-Sprayed Thermal Barrier Coating System

    Science.gov (United States)

    Bai, Yu; Ding, Chunhua; Li, Hongqiang; Han, Zhihai; Ding, Bingjun; Wang, Tiejun; Yu, Lie

    2013-10-01

    In this work, Y2O3 stabilized zirconia-based thermal barrier coatings (TBCs) were deposited by conventional atmospheric plasma spraying (APS) and high efficiency supersonic atmospheric plasma spraying (SAPS), respectively. The effect of Al2O3 layer stability on the isothermal growth behavior of thermally grown oxides (TGOs) was studied. The results revealed that the Al2O3 layer experienced a three-stage change process, i.e., (1) instantaneous growth stage, (2) steady-state growth stage, and (3) depletion stage. The thickness of Al2O3 scale was proved to be an important factor for the growth rate of TGOs. The SAPS-TBCs exhibited a higher Al2O3 stability and better oxidation resistance as compared with the APS-TBCs. Additionally, it was found that inner oxides, especially nucleated on the top of the crest, continually grew and swallowed the previously formed Al2O3 layer, leading to the granulation and disappearance of continuous Al2O3 scale, which was finally replaced by the mixed oxides and spinel.

  5. Flow characteristic of in-flight particles in supersonic plasma spraying process

    Science.gov (United States)

    Wei, Pei; Wei, Zhengying; Zhao, Guangxi; Du, Jun; Bai, Y.

    2016-09-01

    In this paper, a computational model based on supersonic plasma spraying (SAPS) is developed to describe the plasma jet coupled with the injection of carrier gas and particles for SAPS. Based on a high-efficiency supersonic spraying gun, the 3D computational model of spraying gun was built to study the features of plasma jet and its interactions with the sprayed particles. Further the velocity and temperature of in-flight particles were measured by Spray Watch 2i, the shape of in-flight particles was observed by scanning electron microscope. Numerical results were compared with the experimental measurements and a good agreement has been achieved. The flight process of particles in plasma jet consists of three stages: accelerated stage, constant speed stage and decelerated stage. Numerical and experimental indicates that the H2 volume fraction in mixture gas of Ar + H2 should keep in the range of 23-26 %, and the distance of 100 mm is the optimal spraying distance in Supersonic atmosphere plasma spraying. Particles were melted and broken into small child particles by plasma jet and the diameters of most child particles were less than 30 μm. In general, increasing the particles impacting velocity and surface temperature can decrease the coating porosity.

  6. Effect of Solid Shield on Coating Properties in Atmospheric Plasma Spray Process

    Science.gov (United States)

    Liu, Ting; Zheng, Lili; Zhang, Hui

    2016-12-01

    This paper investigates the impact of shrouded shield structure on plasma spray processes and the selection of optimal shield structure. Response of plasma flame characteristics to solid shield structures is studied first, and experimental investigations are then performed for both atmospheric (APS) and shrouded (SPS) plasma spray processes. It is found that the usage of conical shield (divergence angle 5.5°) with 90 mm in length is effective to form a low-oxygen (3000 K) region in the plasma flame and this region can cover the majority area for particles passing by. The average particle temperature is higher in SPS than in APS with the given conditions, and such behavior is intensified as solid shield length increases. Using the SPS process, more disk-shaped splats are obtained, and the oxygen concentration in coating is significantly reduced. The degree of the oxidation in the coatings is further reduced as the length of the solid shield increases from 50 to 90 mm. Applying solid shield will lead to high flame temperature and low oxidation; however, the substrate overheating and velocity reduction may occur. For the cases studied, the optimal shield length is around 90 mm.

  7. Low friction stainless steel coatings graphite doped elaborated by air plasma sprayed

    Science.gov (United States)

    Harir, A.; Ageorges, H.; Grimaud, A.; Fauchais, P.; Platon, F.

    2004-10-01

    A new process has been developed to incorporate graphite particles into a stainless steel coating during its formation. Four means have been tested to inject the graphite particles outside the plasma jet and its plume: graphite suspension, a graphite rod rubbed on the rotating sample, powder injection close to the substrate with an injector, or a specially designed guide. The last process has been shown to be the most versatile and the most easily controllable. It allows the incorporation of between 2 and 12 vol.% of graphite particles (2 15 µm) within the plasma sprayed stainless steel coatings. A volume fraction of 2% seems to give the best results with a slight decrease (6%) of the coating hardness. This volume fraction also gave the best results in dry friction on the pin-on-disk apparatus. Depending on the sliding velocity (0.1 0.5 m/s) and loads (3.7 28 N), the dry friction coefficient against a 100C6 pin is reduced by between 1.5 and 4 compared with that obtained with plasma sprayed stainless steel.

  8. Fabrication and electrochemical performance of solid oxide fuel cell components by atmospheric and suspension plasma spray

    Institute of Scientific and Technical Information of China (English)

    XIA Wei-sheng; YANG Yun-zhen; ZHANG Hai-ou; WANG Gui-lan

    2009-01-01

    The theory of functionally graded material (FGM) was applied in the fabrication process of PEN (Positive- Electrolyte-Negative),the core component of solid oxide fuel cell (SOFC).To enhance its electrochemical performance,the functionally graded PEN of planar SOFC was prepared by atmospheric plasma spray (APS).The cross-sectional SEM micrograph and element energy spectrum of the resultant PEN were analyzed.Its interface resistance was also compared with that without the graded layers to investigate the electrochemical performance enhanced by the functionally graded layers.Moreover,a new process,suspension plasma spray (SPS) was applied to preparing the SOFC electrolyte.Higher densification of the coating by SPS,1.61%,is observed,which is helpful to effectively improve its electrical conductivity.The grain size of the electrolyte coating fabricated by SPS is also smaller than that by APS,which is more favourable to obtain the dense electrolyte coatings.To sum up,all mentioned above can prove that the hybrid process of APS and SPS could be a better approach to fabricate the PEN of SOFC stacks,in which APS is for porous electrodes and SPS for dense electrolyte.

  9. Microstructure and Tribological Properties of Plasma-sprayed Nanostructured Sulfide Coating

    Institute of Scientific and Technical Information of China (English)

    Yang XU; Yaohui GUAN; Zhongyu ZHENG; Xiaohui TONG

    2006-01-01

    The friction and wear properties of plasma-sprayed nanostructured FeS coating were investigated on an MHK-500 friction and wear tester under both oil lubrication and dry friction condition. The microstructure, worn surface morphology and phase composition of the coating were characterized by scanning electron microscopy(SEM)and X-ray diffraction(XRD). It was found that the coating was mainly composed of FeS, a small quantity of Fe1-xS and oxide were also found. The coating was formed by small particles of 50~100 nm in size. The thickness of the coating is approximately 150μm. The friction-reduction and wear-resistance properties of plasma-sprayed nanostructured FeS coating were superior to that of GCr15 steel substrate.Especially under oil lubrication condition, the friction coefficient of nanostructured FeS coating was 50% of that of GCr15 steel, the wear scar widths of the coating were also reduced to nearly 50% of that of GCr15 steel under high load. The failure of the coating was mainly attributed to plastic deformation under both oil lubrication and dry friction condition.

  10. Nano Structured Plasma Spray Coating for Wear and High Temperature Corrosion Resistance Applications

    Science.gov (United States)

    Ghosh, D.; Shukla, A. K.; Roy, H.

    2014-04-01

    The nano structured coating is a major challenge today to improve the different mechanical properties, wear and high temperature corrosion resistance behaviour of different industrial alloys. This paper is a review on synthesis of nano powder, plasma spraying methods, techniques of nano structured coating by plasma spray method, mechanical properties, tribological properties and high temperature corrosion behaviour of nano structured coating. Nano structured coatings of ceramic powders/composites are being developed for wide variety of applications like boiler, turbine and aerospace industries, which requires the resistance against wear, corrosion, erosion etc. The nano sized powders are subjected to agglomeration by spray drying, after which nano structured coating can be successfully applied over the substrate. Nano structured coating shows improved mechanical wear resistance and high temperature corrosion resistance. The significant improvement of wear and corrosion resistance is mainly attributed to formation of semi molten nano zones in case of nano structured coatings. The future scope of application of nano structured coating has also been highlighted in this paper.

  11. Influence of Different Interfacial Conditions on Bond Strength of Plasma - Sprayed Tungsten Coatings

    Energy Technology Data Exchange (ETDEWEB)

    Song, S.X. [Research Center on Fusion Materials (RCFM), University of Science and Technology Beijing (USTB), 10008 3 Beijing (China); Zhou, Z.; Ge, C. [Lab. of Special Ceramic and P/M, University of Science and Technology, 100083 Beijing (China)

    2007-07-01

    Full text of publication follows: How to improve the interfacial performance and obtain high bond strength is a common problem in plasma-sprayed W coatings onto Cu substrates as plasma-facing components (PFC). This phenomenon results from the high interfacial residual stress state created by different thermal expansion coefficients, melting points and elastic modulus between W and Cu during the spraying processes. In this paper, tungsten coatings were deposited onto the oxygen free copper by plasma spraying. Various interlayers were designed to relieve the residual stress between W coatings and Cu substrates. These interlayers included NiCrAl, NiAl, NiCrAlY, W(50 %) Cu (50%) and functionally graded bonding coatings NiCrAl/AlCu, W/Cu and so on. SEM, EDS and XRD were employed to investigate the microstructure, photographs and compositions of the interfacial layers. Finite element coupled heat transfer and elastic-plastic thermal stress analysis using finite element analysis (FEA) were utilized to simulate the residual stress generation during the depositing process. The residual stresses were also calculated using this method to explain the variations of the interfacial characteristics with the various interlayers. In addition, tensile tests in conjunction with finite element analysis (FEA) were also performed to better understand the influence of both material selection and component distribution on bonding strength between the coatings and the substrates. As a result, a predicted coating system with the possibility of reducing the residual stress level was also proposed. (authors)

  12. Factors affecting the microstructural stability and durability of thermal barrier coatings fabricated by air plasma spraying

    Energy Technology Data Exchange (ETDEWEB)

    Helminiak, M.A.; Yanar, N.M.; Pettit, F.S.; Meier, G.H. [National Energy Technology Laboratory, Pittsburgh, PA 15236 (United States); Department of Mechanical Engineering and Materials Science, University of Pittsburgh, 636 Benedum Hall, 3700 O& #x27; Hara Street, Pittsburgh, PA 15261 (United States); Taylor, T.A. [Praxair Surface Technologies, Inc., 1400 Polco Street, Indianapolis, IN 46224 (United States)

    2012-10-15

    The high-temperature behavior of high-purity, low-density (HP-LD) air plasma sprayed (APS) thermal barrier coatings (TBCs) with NiCoCrAlY bond coats deposited by argon-shrouded plasma spraying is described. The high purity yttria-stabilized zirconia resulted in top coats which are highly resistant to sintering and transformation from the metastable tetragonal phase to the equilibrium mixture of monoclinic and cubic phases. The thermal conductivity of the as-processed TBC is low but increases during high temperature exposure even before densification occurs. The porous topcoat microstructure also resulted in good spallation resistance during thermal cycling. The actual failure mechanisms of the APS coatings were found to depend on topcoat thickness, topcoat density, and the thermal cycle frequency. The failure mechanisms are described and the durability of the HP-LD coatings is compared with that of state-of-the-art electron beam physical vapor deposition TBCs. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  13. Characterization of Microstructure and Thermal Properties of YSZ Coatings Obtained by Axial Suspension Plasma Spraying (ASPS)

    Science.gov (United States)

    Ganvir, Ashish; Curry, Nicholas; Björklund, Stefan; Markocsan, Nicolaie; Nylén, Per

    2015-10-01

    The paper aims at demonstrating various microstructures which can be obtained using the suspension spraying technique and their respective significance in enhancing the thermal insulation property of a thermal barrier coating. Three different types of coating microstructures are discussed which were produced by the Axial Suspension Plasma Spraying. Detailed characterization of coatings was then performed. Optical and scanning electron microscopy were utilized for microstructure evaluations; x-ray diffraction for phase analysis; water impregnation, image analysis, and mercury intrusion porosimetry for porosity analysis, and laser flash analysis for thermal diffusivity measurements were used. The results showed that Axial Suspension Plasma Spraying can generate vertically cracked, porous, and feathery columnar-type microstructures. Pore size distribution was found in micron, submicron, and nanometer range. Higher overall porosity, the lower density of vertical cracks or inter-column spacing, and higher inter-pass porosity favored thermal insulation property of the coating. Significant increase in thermal diffusivity and conductivity was found at higher temperature, which is believed to be due to the pore rearrangement (sintering and pore coarsening). Thermal conductivity values for these coatings were also compared with electron beam physical vapor deposition (EBPVD) thermal barrier coatings from the literature and found to be much lower.

  14. Thickness measurement approach for plasma sprayed coatings using ultrasonic testing technique

    Institute of Scientific and Technical Information of China (English)

    LIN Li; LI Xi-meng; XU Zhi-hui; LEI Ming-kai

    2004-01-01

    The special ultrasonic testing system has been developed for thickness measurement of plasma sprayed coatings. The ultrasonic immersion method was used to obtain stable coupling condition and avoid other disadvantages of contact method. Spherical acoustic lens were designed to focus ultrasonic beam so as to improve beam directivity and concentrate ultrasonic energy. To increase testing precision and avoid mussy wave signals, moderate pulse width and frequency of the transducer has been selected. The displacement of transducer in X-Y-Z directions was precisely manipulated by step-controlled system to insure the accuracy of focus length and repetition of measurement. Optimized testing conditions (with the transducer of center frequency of 10 MHz and crystal diameter of 8 mm, focus length of 9.5 mm, diameter of focal column of 0. 1 mm and length of focal column of 0.27 mm) were selected to determine the thickness between 285 -414 μm of ZrO2 coatings plasma sprayed on the nickel based superalloy. The frequency interval of the periodic extremums in ultrasonic power spectra decreases with increasing coating thickness. The ultrasonic results accord with those of metallographical method.

  15. Temperature Measurement Challenges and Limitations for In-Flight Particles in Suspension Plasma Spraying

    Science.gov (United States)

    Aziz, Bishoy; Gougeon, Patrick; Moreau, Christian

    2017-03-01

    Suspension plasma spraying (SPS) acquires a significant interest from the industry. The deposited coatings using this technique were proved to have unique microstructural features compared to those built by conventional plasma spraying techniques. In order to optimize this process, in-flight particle diagnostics is considered a very useful tool that helps to control various spraying parameters and permits better coating reproducibility. In that context, the temperature of in-flight particles is one of the most important key elements that helps to optimize and control the SPS process. However, the limitations and challenges associated with this process have a significant effect on the accuracy of two-color pyrometric techniques used to measure the in-flight particle temperature. In this work, the influence of several nonthermal radiation sources on the particle temperature measurement is studied. The plasma radiation scattered by in-flight particles was found to have no significant influence on temperature measurement. Moreover, the detection of the two-color signals at two different locations was found to induce a significant error on temperature measurement. Finally, the plasma radiation surrounding the in-flight particles was identified as the main source of error on the temperature measurement of in-flight particles.

  16. Comparison of thermal shock behaviors between plasma-sprayed nanostructured and conventional zirconia thermal barrier coatings

    Institute of Scientific and Technical Information of China (English)

    LIU Chun-bo; ZHANG Zhi-min; JIANG Xian-liang; LIU Min; ZHU Zhao-hui

    2009-01-01

    NiCoCrAlTaY bond coat was deposited on pure nickel substrate by low pressure plasma spraying(LPPS), and ZrO2-8%Y2O3 (mass fraction) nanostructured and ZrO2-7%Y2O3 (mass fraction) conventional thermal barrier coatings(TBCs) were deposited by air plasma spraying(APS). The thermal shock behaviors of the nanostructured and conventional TBCs were investigated by quenching the coating samples in cold water from 1 150, 1 200 and 1 250 ℃, respectively. Scanning electron microscopy(SEM) was used to examine the microstructures of the samples after thermal shock testing. Energy dispersive analysis of X-ray(EDAX) was used to analyze the interface diffusion behavior of the bond coat elements. X-ray diffractometry(XRD) was used to analyze the constituent phases of the samples. Experimental results indicate that the nanostructured TBC is superior to the conventional TBC in thermal shock performance. Both the nanostructured and conventional TBCs fail along the bond coat/substrate interface. The constituent phase of the as-sprayed conventional TBC is diffusionless-transformed tetragonal(t′). However, the constituent phase of the as-sprayed nanostructured TBC is cubic(c). There is a difference in the crystal size at the spalled surfaces of the nanostructured and conventional TBCs. The constituent phases of the spalled surfaces are mainly composed of Ni2.88Cr1.12 and oxides of bond coat elements.

  17. Thermal Conductivity Analysis and Lifetime Testing of Suspension Plasma-Sprayed Thermal Barrier Coatings

    Directory of Open Access Journals (Sweden)

    Nicholas Curry

    2014-08-01

    Full Text Available Suspension plasma spraying (SPS has become an interesting method for the production of thermal barrier coatings for gas turbine components. The development of the SPS process has led to structures with segmented vertical cracks or column-like structures that can imitate strain-tolerant air plasma spraying (APS or electron beam physical vapor deposition (EB-PVD coatings. Additionally, SPS coatings can have lower thermal conductivity than EB-PVD coatings, while also being easier to produce. The combination of similar or improved properties with a potential for lower production costs makes SPS of great interest to the gas turbine industry. This study compares a number of SPS thermal barrier coatings (TBCs with vertical cracks or column-like structures with the reference of segmented APS coatings. The primary focus has been on lifetime testing of these new coating systems. Samples were tested in thermo-cyclic fatigue at temperatures of 1100 °C for 1 h cycles. Additional testing was performed to assess thermal shock performance and erosion resistance. Thermal conductivity was also assessed for samples in their as-sprayed state, and the microstructures were investigated using SEM.

  18. Performance Testing of Suspension Plasma Sprayed Thermal Barrier Coatings Produced with Varied Suspension Parameters

    Directory of Open Access Journals (Sweden)

    Nicholas Curry

    2015-07-01

    Full Text Available Suspension plasma spraying has become an emerging technology for the production of thermal barrier coatings for the gas turbine industry. Presently, though commercial systems for coating production are available, coatings remain in the development stage. Suitable suspension parameters for coating production remain an outstanding question and the influence of suspension properties on the final coatings is not well known. For this study, a number of suspensions were produced with varied solid loadings, powder size distributions and solvents. Suspensions were sprayed onto superalloy substrates coated with high velocity air fuel (HVAF -sprayed bond coats. Plasma spray parameters were selected to generate columnar structures based on previous experiments and were maintained at constant to discover the influence of the suspension behavior on coating microstructures. Testing of the produced thermal barrier coating (TBC systems has included thermal cyclic fatigue testing and thermal conductivity analysis. Pore size distribution has been characterized by mercury infiltration porosimetry. Results show a strong influence of suspension viscosity and surface tension on the microstructure of the produced coatings.

  19. Stress Analysis and Failure Mechanisms of Plasma-Sprayed Thermal Barrier Coatings

    Science.gov (United States)

    Yang, Jiasheng; Wang, Liang; Li, Dachuan; Zhong, Xinghua; Zhao, Huayu; Tao, Shunyan

    2017-06-01

    Yttria-stabilized zirconia coatings were deposited by plasma spraying and heat-treated at 1100 °C for 50, 100, 150, and 200 h in air, respectively. Mechanical properties including microhardness and Young's modulus were evaluated using the nanoindentation test. Residual stresses in the ceramic topcoat and the thermally grown oxide (TGO) layer were measured using Raman spectroscopy and photoluminescence piezo-spectroscopy (PLPS) techniques, respectively. The results showed that both the modulus and hardness increased with the thermal exposure time up to 100 h and then gradually decreased. The accumulated tensile stress in the as-sprayed topcoat changed to compressive stress after thermal exposure, and the compressive stress in the topcoat increased with an increase of thermal exposure time up to 150 h. The average compressive stresses in the TGO layer were higher than that of the cross-sectional topcoat, and the measured in-plane compressive stress increased firstly and then gradually decreased with increasing exposure time. The local interface geometry strongly affect the nature and evolution of hydrostatic stresses in the TGO. Finally, the crack initiation and propagation at the topcoat/TGO/bondcoat interface has been discussed with respect to the residual stresses in the plasma-sprayed TBC system.

  20. Indentations on Air Plasma Sprayed Thermal Barrier Coatings Prepared by Different Starting Granules

    Directory of Open Access Journals (Sweden)

    Yong Suk Heo

    2015-01-01

    Full Text Available The effect of starting granules on the indentation properties of air plasma sprayed thermal barrier coatings (TBCs is investigated in this paper. Various kinds of spray-dried granules are prepared from different processing conditions, especially varying solvent and dispersant, showing a deformed hollow-typed and a filled spherical-typed granule. The similar coating thicknesses are prepared by adjusting process parameters during air plasma spray. All XRD peaks in phase analysis are tetragonal and cubic phases without any monoclinic phase after the starting granules were heat-treated. A relatively porous microstructure of the coating layer could be obtained from the monodisperse granules, while a relatively dense microstructure resulted from the hollow-typed granules. The morphology and distribution of the granules crucially affect the microstructure of thermal barrier coatings and thus have influences on indentation properties such as indentation stress-strain curves, contact damage, and hardness. The implication concerning microstructure design of TBCs for gas turbine applications is considered.

  1. Piezospectroscopic measurements capturing the evolution of plasma spray-coating stresses with substrate loads.

    Science.gov (United States)

    Freihofer, Gregory; Fugon-Dessources, Daniela; Ergin, Emrecan; Van Newkirk, Amy; Gupta, Ankur; Seal, Sudipta; Schülzgen, Axel; Raghavan, Seetha

    2014-02-12

    Plasma-spray coatings have a unique microstructure composed of various types of microcracks and weakly bonded interfaces which dictate their nonlinear mechanical properties. The intrinsic photo-luminescence (PL) characteristics of alpha-alumina (α-Al2O3) within these coatings offer a diagnostic functionality, enabling these properties to be probed experimentally at the microscale, under substrate loading. The piezospectroscopic (PS) measurements from the coatings are capable of revealing microstructural stress at high spatial resolution. Here, for the first time, the evolution of stresses within air plasma spray (APS) coatings under increasing substrate loads were captured using piezospectroscopy. With mechanical cycling of the substrate, the PS properties revealed anelastic and inelastic behavior and a relaxation of residual tensile stress within the APS coatings. With decreasing substrate thickness, the coating was observed to sustain more stress, as the substrate's influence on the mechanical behavior decreased. The findings provide an insight into the microstructural response that can serve as the basis for model validation and subsequently drive the design process for these coatings.

  2. Plasma Spray-Physical Vapor Deposition (PS-PVD) of Ceramics for Protective Coatings

    Science.gov (United States)

    Harder, Bryan J.; Zhu, Dongming

    2011-01-01

    In order to generate advanced multilayer thermal and environmental protection systems, a new deposition process is needed to bridge the gap between conventional plasma spray, which produces relatively thick coatings on the order of 125-250 microns, and conventional vapor phase processes such as electron beam physical vapor deposition (EB-PVD) which are limited by relatively slow deposition rates, high investment costs, and coating material vapor pressure requirements. The use of Plasma Spray - Physical Vapor Deposition (PS-PVD) processing fills this gap and allows thin (coatings of less than 100 microns to be generated with the flexibility to tailor microstructures by changing processing conditions. Coatings of yttria-stabilized zirconia (YSZ) were applied to NiCrAlY bond coated superalloy substrates using the PS-PVD coater at NASA Glenn Research Center. A design-of-experiments was used to examine the effects of process variables (Ar/He plasma gas ratio, the total plasma gas flow, and the torch current) on chamber pressure and torch power. Coating thickness, phase and microstructure were evaluated for each set of deposition conditions. Low chamber pressures and high power were shown to increase coating thickness and create columnar-like structures. Likewise, high chamber pressures and low power had lower growth rates, but resulted in flatter, more homogeneous layers

  3. Oxidation Behavior of Titanium Carbonitride Coating Deposited by Atmospheric Plasma Spray Synthesis

    Science.gov (United States)

    Zhu, Lin; He, Jining; Yan, Dianran; Liao, Hanlin; Zhang, Nannan

    2017-08-01

    Abstract: As a high-hardness and anti-frictional material, titanium carbonitride (TiCN) thick coatings or thin films are increasingly being used in many industrial fields. In the present study, TiCN coatings were obtained by atmospheric plasma spray synthesis or reactive plasma spray. In order to promote the reaction between the Ti particles and reactive gases, a home-made gas tunnel was mounted on a conventional plasma gun to perform the spray process. The oxidation behavior of the TiCN coatings under different temperatures in static air was carefully investigated. As a result, when the temperature was over 700 °C, the coatings suffered from serious oxidation, and finally they were entirely oxidized to the TiO2 phase at 1100 °C. The principal oxidation mechanism was clarified, indicating that the oxygen can permeate into the defects and react with TiCN at high temperatures. In addition, concerning the use of a TiCN coating in high-temperature conditions, the microhardness of the oxidized coatings at different treatment temperatures was also evaluated.

  4. Electrochemical Impedance Studies on Tribocorrosion Behavior of Plasma-Sprayed Al2O3 Coatings

    Science.gov (United States)

    Liu, Zhe; Chu, Zhenhua; Chen, Xueguang; Dong, Yanchun; Yang, Yong; Li, Yingzhen; Yan, Dianran

    2015-06-01

    In this paper, the tribocorrosion of plasma-sprayed Al2O3 coatings in simulated seawater was investigated by electrochemical impedance spectroscopy (EIS) technique, complemented by scanning electron microscopy to observe the morphology of the tribocorrosion attack. Base on EIS of plasma-sprayed Al2O3 coatings undergoing long-time immersion in simulated seawater, the corrosion process of Al2O3 coatings can be divided into the earlier stage of immersion (up to 20 h) and the later stage (beyond 20 h). Then, the wear tests were carried out on the surface of Al2O3 coating undergoing different times of immersion to investigate the influence of wear on corrosion at different stages. The coexistence of wear and corrosion condition had been created by a boron nitride grinding head rotating on the surface of coatings corroded in simulated seawater. The measured EIS and the values of the fitting circuit elements showed that wear accelerated corrosion at the later stage, meanwhile, corrosion accelerated wear with the immersion time increasing.

  5. Reactive Plasma-Sprayed Aluminum Nitride-Based Coating Thermal Conductivity

    Science.gov (United States)

    Shahien, Mohammed; Yamada, Motohiro; Fukumoto, Masahiro; Egota, Kazumi; Okamoto, Kenji

    2015-12-01

    Recently, thick aluminum nitride/alumina (AlN/Al2O3) composite coatings were successfully fabricated through the reactive plasma spraying of fine Al2O3/AlN mixture in the N2/H2 atmospheric plasma. The coatings consist of AlN, Al5O6N, γ-Al2O3, and α-Al2O3 phases. This study will evaluate the thermal conductivity of these complicated plasma-sprayed coatings and optimize the controlling aspects. Furthermore, the influence of the process parameters on the coatings thermal conductivity will be investigated. The fabricated coatings showed very low thermal conductivity (2.43 W/m K) compared to the AlN sintered compacts. It is attributed to the phase composition of the fabricated coatings, oxide content, and porosity. The presence of Al2O3, Al5O6N and the high coating porosity decreased its thermal conductivity. The presence of oxygen in the AlN lattice creates Al vacancies which lead to phonon scattering and therefore suppressed the thermal conductivity. The formation of γ-Al2O3 phase in the coating leads to further decrease in its conductivity, due to its lower density compared to the α-phase. Moreover, the high porosity of the coating strongly suppressed the conductivity. This is due to the complicated microstructure of plasma spray coatings (splats, porosity, and interfaces, particularly in case of reactive spray process), which obviously lowered the conductivity. Furthermore, the measured coating density was lower than the AlN value and suppressed the coating conductivity. In addition, the spraying parameter showed a varied effect on the coating phase composition, porosity, density, and therefore on its conductivity. Although the N2 gas flow improved the nitride content, it suppressed the thermal conductivity gradually. It is attributed to the further increase in the porosity and further decrease in the density of the coatings with the N2 gas. Furthermore, increasing the arc did not show a significant change on the coating thermal conductivity. On the other hand

  6. Solid oxide fuel cell electrolytes produced via very low pressure suspension plasma spray and electrophoretic deposition

    Science.gov (United States)

    Fleetwood, James D.

    Solid oxide fuel cells (SOFCs) are a promising element of comprehensive energy policies due to their direct mechanism for converting the oxidization of fuel, such as hydrogen, into electrical energy. Both very low pressure plasma spray and electrophoretic deposition allow working with high melting temperature SOFC suspension based feedstock on complex surfaces, such as in non-planar SOFC designs. Dense, thin electrolytes of ideal composition for SOFCs can be fabricated with each of these processes, while compositional control is achieved with dissolved dopant compounds that are incorporated into the coating during deposition. In the work reported, sub-micron 8 mole % Y2O3-ZrO2 (YSZ) and gadolinia-doped ceria (GDC), powders, including those in suspension with scandium-nitrate dopants, were deposited on NiO-YSZ anodes, via very low pressure suspension plasma spray (VLPSPS) at Sandia National Laboratories' Thermal Spray Research Laboratory and electrophoretic deposition (EPD) at Purdue University. Plasma spray was carried out in a chamber held at 320 - 1300 Pa, with the plasma composed of argon, hydrogen, and helium. EPD was characterized utilizing constant current deposition at 10 mm electrode separation, with deposits sintered from 1300 -- 1500 °C for 2 hours. The role of suspension constituents in EPD was analyzed based on a parametric study of powder loading, powder specific surface area, polyvinyl butyral (PVB) content, polyethyleneimine (PEI) content, and acetic acid content. Increasing PVB content and reduction of particle specific surface area were found to eliminate the formation of cracks when drying. PEI and acetic acid content were used to control suspension stability and the adhesion of deposits. Additionally, EPD was used to fabricate YSZ/GDC bilayer electrolyte systems. The resultant YSZ electrolytes were 2-27 microns thick and up to 97% dense. Electrolyte performance as part of a SOFC system with screen printed LSCF cathodes was evaluated with peak

  7. Effect of the thickness on properties of Al{sub 2}O{sub 3} coatings deposited by plasma spraying

    Energy Technology Data Exchange (ETDEWEB)

    Yin Zhijian [Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai 200050 (China); Graduate School of the Chinese Academy of Sciences, Beijing 100049 (China); Tao Shunyan, E-mail: shunyantao@mail.sic.ac.cn [Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai 200050 (China); Zhou Xiaming [Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai 200050 (China)

    2011-01-15

    Al{sub 2}O{sub 3} coatings with different thicknesses (160, 320, 480 and 640 {mu}m) were deposited on stainless steel substrate by plasma spraying. The variation in microstructural characteristics and properties of coatings with various thicknesses was investigated. Powders morphology and the microstructure of as-sprayed coatings were characterized by scanning electron microscopy and optical microscopy. The microhardness was measured using a Vickers' indentor. The corrosion behaviour of plasma-sprayed Al{sub 2}O{sub 3} coatings in 1 N H{sub 2}SO{sub 4} solution at a temperature of 25 deg. C was evaluated by electrochemistry method. Experimental results indicated that surface roughness showed no obvious dependence on the coating thickness. However, the porosity of Al{sub 2}O{sub 3} coating was increased with increased thickness. The enhanced coating thickness also resulted in decreasing microhardness and reduced corrosion resistance. In this study, the Al{sub 2}O{sub 3} coating with thickness of 160 {mu}m possesses the lowest porosity, the highest hardness and superior corrosion resistance. Research Highlights: {yields} Increase of coating thickness shows no obvious effect on phase composition and surface roughness of plasma sprayed Al{sub 2}O{sub 3} coatings. {yields} Variation of porosity and microhardness presents dependence on coating thickness parameter. {yields} Increasing coating thickness leads to reduced corrosion resistance of plasma sprayed Al{sub 2}O{sub 3} coating.

  8. Improvement in the properties of plasma-sprayed metallic, alloy and ceramic coatings using dry-ice blasting

    Science.gov (United States)

    Dong, Shujuan; Song, Bo; Hansz, Bernard; Liao, Hanlin; Coddet, Christian

    2011-10-01

    Dry-ice blasting, as an environmental-friendly method, was introduced into atmospheric plasma spraying for improving properties of metallic, alloy and ceramic coatings. The deposited coatings were then compared with coatings plasma-sprayed using conventional air cooling in terms of microstructure, temperature, oxidation, porosity, residual stress and adhesion. It was found that a denser steel or CoNiCrAlY alloy coating with a lower content of oxide can be achieved with the application of dry-ice blasting during the plasma spraying. In addition, the adhesive strength of Al 2O 3 coating deposited with dry-ice blasting exceeded 60 MPa, which was nearly increased by 30% compared with that of the coating deposited with conventional air cooling. The improvement in properties of plasma-sprayed metallic, alloy and ceramic coatings caused by dry-ice blasting was attributed to the decrease of annulus-ringed disk like splats, the better cooling efficiency of dry-ice pellets and even the mechanical effect of dry-ice impact.

  9. Hydroxyapatite coatings deposited by liquid precursor plasma spraying: controlled dense and porous microstructures and osteoblastic cell responses

    Energy Technology Data Exchange (ETDEWEB)

    Huang Yi; Song Lei; Liu Xiaoguang; Xiao Yanfeng; Wu Yao; Chen Jiyong; Wu Fang; Gu Zhongwei, E-mail: fangwu0808@yahoo.co, E-mail: fwu@scu.edu.c [National Engineering Research Center for Biomaterials, Sichuan University, Chengdu 610064 (China)

    2010-12-15

    Hydroxyapatite coatings were deposited on Ti-6Al-4V substrates by a novel plasma spraying process, the liquid precursor plasma spraying (LPPS) process. X-ray diffraction results showed that the coatings obtained by the LPPS process were mainly composed of hydroxyapatite. The LPPS process also showed excellent control on the coating microstructure, and both nearly fully dense and highly porous hydroxyapatite coatings were obtained by simply adjusting the solid content of the hydroxyapatite liquid precursor. Scanning electron microscope observations indicated that the porous hydroxyapatite coatings had pore size in the range of 10-200 {mu}m and an average porosity of 48.26 {+-} 0.10%. The osteoblastic cell responses to the dense and porous hydroxyapatite coatings were evaluated with human osteoblastic cell MG-63, in respect of the cell morphology, proliferation and differentiation, with the hydroxyapatite coatings deposited by the atmospheric plasma spraying (APS) process as control. The cell experiment results indicated that the heat-treated LPPS coatings with a porous structure showed the best cell proliferation and differentiation among all the hydroxyapatite coatings. Our results suggest that the LPPS process is a promising plasma spraying technique for fabricating hydroxyapatite coatings with a controllable microstructure, which has great potential in bone repair and replacement applications.

  10. Anisotropic Mechanical Properties of Plasma-Sprayed Thermal Barrier Coatings at High Temperature Determined by Ultrasonic Method

    Science.gov (United States)

    Wei, Qin; Zhu, Jianguo; Chen, Wei

    2016-02-01

    The mechanical properties of plasma-sprayed thermal barrier coatings (TBC) are of great scientific and technological significance for the design and fabrication of TBC systems. The ultrasonic method combined with a sing-around method for mechanical properties measurement of TBC is deduced and the elastic modulus can be determined in the spray, or longitudinal, direction, and the transverse direction. Tested specimens of plasma-sprayed TBC are detached from the substrate and treated with thermal exposure at 1400 °C. The elastic moduli along the longitudinal and transverse directions of the TBCs are measured by different types of ultrasonic waves combined with a sing-around method, while the Poisson's ratio is also obtained simultaneously. The experimental results indicate that the magnitude of longitudinal elastic modulus is larger than that of the transverse one, and thus the plasma-sprayed TBC has an anisotropic mechanical property. Moreover, the elastic moduli along both longitudinal and transverse directions change with high-temperature exposure time, which consists of a rapid increasing stage followed by a slow decreasing stage. In addition, the magnitude of Poisson's ratio increases slightly from 0.05 to 0.2 with the high-temperature exposure time. Generally, the microstructures in the plasma-sprayed coatings and their evolution in a high-temperature environment are the main causes of the varying anisotropic mechanical properties.

  11. A systematic review on the long-term success of calcium phosphate plasma-spray-coated dental implants

    NARCIS (Netherlands)

    Oirschot, B.A.J.A. van; Bronkhorst, E.M.; Beucken, J.J.J.P van den; Meijer, G.J.; Jansen, J.A.; Junker, R.

    2016-01-01

    The objectives of the current review were (1) to systematically appraise, and (2) to evaluate long-term success data of calcium phosphate (CaP) plasma-spray-coated dental implants in clinical trials with at least 5 years of follow-up. To describe the long-term efficacy of functional implants, the

  12. Reactive Plasma Sprayed TiN Coating and Its Thermal Stability

    Institute of Scientific and Technical Information of China (English)

    ZOU Dong-li; YAN Dian-ran; HE Ji-ning; LI Xiang-zhi; DONG Yan-chun; ZHANG Jian-xin

    2007-01-01

    TiN coating was prepared by reactive plasma spraying in the Ar and N2 containing plasma jet. The results of XRD show that the TiN coating consists of TiN and Ti3O, neither Ti2N nor TiO2 phases. The toughening mechanism was characterized by analyzing the SEM morphologies of the TiN coating's indentation of microhardness and fracture surfaces. The results indicate that the coating possesses a high toughness. The adhesion strength among the TiN layers is 25.88 MPa, which is slightly lower than that of the Ni/Al bonding coating. The oxidation process of the RPS TiN coating is TiN→Ti3O→TiO2.

  13. Friction of tungsten carbide-cobalt coatings obtained by means of plasma spraying

    Energy Technology Data Exchange (ETDEWEB)

    Cartier, M. (Hydromecanique et Frottement, Centre de Recherches, 42 - Andreziux-Boutheon (France)); McDonnell, L.; Cashell, E.M. (CRTC, Cork (Ireland))

    1991-11-29

    A study of the frictional properties of WC-Co-type coatings obtained by plasma spraying was carried out, the influence of the majority of the parameters involved in atmospheric spraying being analysed. This study of the correlations between the tribological behaviour and the compositionl of the coatings shows that friction is mainly determined by the method and degree of decomposition of the carbides. These in turn are linked to the effects of heat and/or oxidation, factors which can change considerably, not only as a function of the method used (plasma power, nature and flow rate of the plasma gases etc.) but also as a function of the coating process and the composition of the original powders. It has been possible to correlate the improvement in the frictional properties (resistance to seizure, reduction in the coefficient of friction) with the presence of free carbon in the coatings, associated with the carbide decomposition process. (orig.).

  14. Preparation and Properties of Plasma Spraying Cu-Al2O3 Gradient Coatings

    Institute of Scientific and Technical Information of China (English)

    Ali LEI; Nan DONG; Lajun FENG

    2007-01-01

    In order to overcome the limitations of low adhesion strength and poor thermal-shock resistance of pure ceramic coatings, Cu-Al2O3 gradient coatings were fabricated by plasma spraying. The microstructure and distribution of Cu-Al2O3 gradient coatings were analyzed. The adhesion strength, thermal-shock resistance and porosity of the coatings were tested. The results show that the composition of the gradient coatings has a gradient distribution along the thickness of coatings. As copper has a relatively low melting point and the molten copper has good wettability on the surface of Al2O3, it can be melted sufficiently and could fill the interstices and pores among the spraying particles effectively, thus improves the adhesion strength, thermal shock resistance and reduces the porosity. The adhesion strength of the gradient coating is 15.2 MPa which is two times of that of the double-layer structure coating.

  15. Mechanical Properties of Air Plasma Sprayed Environmental Barrier Coating (EBC) Materials

    Science.gov (United States)

    Richards, Bradley; Zhu, Dongming; Ghosn, Louis; Wadley, Haydn

    2015-01-01

    Development work in Environmental Barrier Coatings (EBCs) for Ceramic Matrix Composites (CMCs) has focused considerably on the identification of materials systems and coating architectures to meet application needs. The evolution of these systems has occurred so quickly that modeling efforts and requisite data for modeling lag considerably behind development. Materials property data exists for many systems in the bulk form, but the effects of deposition on the critical properties of strength and fracture behavior are not well studied. We have plasma sprayed bulk samples of baseline EBC materials (silicon, ytterbium disilicate) and tested the mechanical properties of these materials to elicit differences in strength and toughness. We have also endeavored to assess the mixed-mode fracture resistance, Gc, of silicon in a baseline EBC applied to SiCSiC CMC via four point bend test. These results are compared to previously determined properties of the comparable bulk material.

  16. Deposition of titanium nitride and hydroxyapatite-based biocompatible composite by reactive plasma spraying

    Science.gov (United States)

    Roşu, Radu Alexandru; Şerban, Viorel-Aurel; Bucur, Alexandra Ioana; Dragoş, Uţu

    2012-02-01

    Titanium nitride is a bioceramic material successfully used for covering medical implants due to the high hardness meaning good wear resistance. Hydroxyapatite is a bioactive ceramic that contributes to the restoration of bone tissue, which together with titanium nitride may contribute to obtaining a superior composite in terms of mechanical and bone tissue interaction matters. The paper presents the experimental results in obtaining composite layers of titanium nitride and hydroxyapatite by reactive plasma spraying in ambient atmosphere. X-ray diffraction analysis shows that in both cases of powders mixtures used (10% HA + 90% Ti; 25% HA + 75% Ti), hydroxyapatite decomposition occurred; in variant 1 the decomposition is higher compared with the second variant. Microstructure of the deposited layers was investigated using scanning electron microscope, the surfaces presenting a lamellar morphology without defects such as cracks or microcracks. Surface roughness values obtained vary as function of the spraying distance, presenting higher values at lower thermal spraying distances.

  17. Behavior of Plasma-Sprayed Hydroxyapatite Coatings onto Carbon/carbon Composites in Simulated Body Fluid

    Science.gov (United States)

    Sui, Jin-Ling; Bo, Wu; Hai, Zhou; Cao, Ning; Li, Mu-Sen

    Two types of hydroxyapatite (HA) coatings onto carbon/carbon composite (C/C composites) substrates, deposited by plasma spraying technique, were immersed in a simulated body fluid (SBF) in order to determine their behavior in conditions similar to the human blood plasma. Calcium ion concentration, pH value, microstructure, and phase compositions were analyzed. Results demonstrated that both the crystal Ca-P phases or the amorphous HA do dissolve slightly, and the dissolution of CaO phases in SBF was evident after 1 day of soaking. The calcium-ion concentration was decreased and the pH value of SBF was increased with the increasing of the immersing time. The precipitation was mainly composed of HA, which was verified by X-ray diffraction (XRD) and electron-probe microanalyzer.

  18. Investigation on in-flight particle velocity in supersonic plasma spraying

    Institute of Scientific and Technical Information of China (English)

    Li Changqing; Ma Shining; Ye Xionglin

    2005-01-01

    In-flight particle velocity and flux distribution were measured using CCD thermal spray monitor system during supersonic plasma spray processing with nano-structured Al203-TiO2 feed stocks. According to the results of particle flux measurement, the largest radian of the divergent particle stream is about 0. 2. Within the measuring range, top speed of inflight particles reached 800 m/s. Particle acceleration was accomplished within 4 cm down stream of the nozzle. Average particle velocity ( about 450 m/s) exceeded local sound speed (340 m/s) even at a mean standoff distance of 17 cm. With increasing mean standoff distance, average velocity of in-flight particle decreased according to a parabolic rule approximately.Image diagnosis showed that the result of in-flight particle velocity measurement is credible.

  19. The Main Issues to Address in Modeling Plasma Spray Torch Operation

    Science.gov (United States)

    Chazelas, C.; Trelles, J. P.; Vardelle, A.

    2017-01-01

    The modeling of plasma torch operation has advanced greatly in the last 15 years due to a better understanding of the underlying physics, development of commercial, open-source computational fluid dynamics softwares, and access to high performance and cloud computing. However, the operation mode of the electric arc in plasma torches is controlled by dynamic, thermal, electromagnetic, acoustic and chemical phenomena that take place at different scales and whose interactions are not completely understood yet. Even though no single model of plasma torch operation fully addresses these phenomena, most of these models are useful tools for parametric studies, if their use is reinforced by knowledge of torch operation and the model predictions are validated against experimental data. To increase the level of predictability of the current models, several further steps are needed. This study examines the issues remaining to be addressed in the modeling of plasma spray torch operation and the current critical aspects of these.

  20. Understanding plasma spraying process and characteristics of DC-arc plasma gun (PJ-100

    Directory of Open Access Journals (Sweden)

    Jovana Ružić

    2012-12-01

    Full Text Available The thermal spray processes are a group of coating processes used to apply metallic or non-metallic coatings. In these processes energy sources are used to heat the coating material (in the form of powder, wire, or rod form to a molten or semi-molten state and accelerated towards a prepared surface by either carrier gases or atomization jets. In plasma spraying process, the spraying material is generally in the form of powder and requires a carrier gas to feed the powder into the plasma jet, which is passing between the hot cathode and the cylindrical nozzle-shaped anode. The design of DC plasma gun (PJ - 100 is designed and manufactured in Serbia. Plasma spaying process, the powder injection with the heat, momentum and mass transfers between particles and plasma jet, and the latest developments related to the production of DC plasma gun are described in this article.

  1. Nanocomposite Lanthanum Zirconate Thermal Barrier Coating Deposited by Suspension Plasma Spray Process

    Science.gov (United States)

    Wang, Chaohui; Wang, You; Wang, Liang; Hao, Guangzhao; Sun, Xiaoguang; Shan, Fan; Zou, Zhiwei

    2014-10-01

    This work seeks to develop an innovative nanocomposite thermal barrier coating (TBC) exhibiting low thermal conductivity and high durability compared with that of current TBCs. To achieve this objective, nanosized lanthanum zirconate particles were selected for the topcoat of the TBC system, and a new process—suspension plasma spray—was employed to produce desirable microstructural features: the nanocomposite lanthanum zirconate TBC contains ultrafine splats and high volume porosity, for lower thermal conductivity, and better durability. The parameters of plasma spray experiment included two main variables: (i) spray distance varying from 40 to 80 mm and (ii) the concentration of suspension 20, 25, and 30 wt.%, respectively. The microstructure of obtained coatings was characterized with scanning electron microscope and x-ray diffraction. The porosity of coatings is in the range of 6-10%, and the single phase in the as-sprayed coatings was pyrochlore lanthanum zirconate.

  2. CMAS Interactions with Advanced Environmental Barrier Coatings Deposited via Plasma Spray- Physical Vapor Deposition

    Science.gov (United States)

    Harder, B. J.; Wiesner, V. L.; Zhu, D.; Johnson, N. S.

    2017-01-01

    Materials for advanced turbine engines are expected to have temperature capabilities in the range of 1370-1500C. At these temperatures the ingestion of sand and dust particulate can result in the formation of corrosive glass deposits referred to as CMAS. The presence of this glass can both thermomechanically and thermochemically significantly degrade protective coatings on metallic and ceramic components. Plasma Spray- Physical Vapor Deposition (PS-PVD) was used to deposit advanced environmental barrier coating (EBC) systems for investigation on their interaction with CMAS compositions. Coatings were exposed to CMAS and furnace tested in air from 1 to 50 hours at temperatures ranging from 1200-1500C. Coating composition and crystal structure were tracked with X-ray diffraction and microstructure with electron microscopy.

  3. Post-treatment of Plasma-Sprayed Amorphous Ceramic Coatings by Spark Plasma Sintering

    Science.gov (United States)

    Chraska, T.; Pala, Z.; Mušálek, R.; Medřický, J.; Vilémová, M.

    2015-04-01

    Alumina-zirconia ceramic material has been plasma sprayed using a water-stabilized plasma torch to produce free standing coatings. The as-sprayed coatings have very low porosity and are mostly amorphous. The amorphous material crystallizes at temperatures above 900 °C. A spark plasma sintering apparatus has been used to heat the as-sprayed samples to temperatures above 900 °C to induce crystallization, while at the same time, a uniaxial pressure of 80 MPa has been applied to their surface. After such post-treatment, the ceramic samples are crystalline and have very low open porosity. The post-treated material exhibits high hardness and significantly increased flexural strength. The post-treated samples have a microstructure that is best described as nanocomposite with the very small crystallites embedded in an amorphous matrix.

  4. Characteristics of Plasma-Sprayed Ceramic Coatings and Their Engineering Application

    Institute of Scientific and Technical Information of China (English)

    DENG Hua-ling; ZHANG Zhong-wen; WU Jun

    2004-01-01

    The microstructure, porosity, microhardness and adhesive strength of three plasma- sprayed ceramic coatings (Al2 O3, Cr2 O3 and Cr3 C2 + NiCr) were tested. The wear resistance of the coatings was characterized through sand blasting test. The results showed that the erosion resistance of Cr2 O3 coating was better than Al2 O3 and Cr3 C2 + NiCr coatings'.Through depositing the coating on the surface of boiler overheater tubes and on the surface of baffle- wall of carrying- coal grain blower to test its anti- erosion performance after a period of running, it was confirmed that the coatings present excellent wear resistance. Accordingly, it also demonstrates that ceramic coating has a promising prospects in surface protection in thermal power stations.

  5. Impacts of friction stir processing on irradiation effects in vacuum-plasma-spray coated tungsten

    Energy Technology Data Exchange (ETDEWEB)

    Ozawa, Kazumi, E-mail: ozawa.kazumi@jaea.go.jp [Fusion Research and Development Directorate, Japan Atomic Energy Agency, 2-166 Obuchi-Omotedate, Rokkasho, Aomori 039-3212 (Japan); Tanigawa, Hiroyasu [Fusion Research and Development Directorate, Japan Atomic Energy Agency, 2-166 Obuchi-Omotedate, Rokkasho, Aomori 039-3212 (Japan); Morisada, Yoshiaki; Fujii, Hidetoshi [Joining and Welding Research Institute, Osaka University, 11-1 Mihogaoka, Ibaraki, Osaka 567-0047 (Japan)

    2015-10-15

    In order to examine the impacts of friction stir processing (FSP) on irradiation effects in vacuum-plasma-spray (VPS) coated tungsten (W), nano indentation hardness was evaluated of three kinds of W materials after self-ion-irradiation to 5.0–5.4 dpa at 500 and 800 °C. The VPS-FSP clearly got grains refined and isotropic compared to bulk-W and the as-VPS-W. Nano indentation hardness remains unchanged for the as-VPS-W and VPS-FSP × 2-W irradiated to 5.4 dpa at 500 °C and it decreased from 1 dpa at 800 °C, while typical irradiation induced hardening was observed for the bulk-W irradiated at 500 °C.

  6. Determination of the Mechanical Properties of Plasma-Sprayed Hydroxyapatite Coatings Using the Knoop Indentation Technique

    Science.gov (United States)

    Hasan, Md. Fahad; Wang, James; Berndt, Christopher

    2015-06-01

    The microhardness and elastic modulus of plasma-sprayed hydroxyapatite coatings were evaluated using Knoop indentation on the cross section and on the top surface. The effects of indentation angle, testing direction, measurement location and applied load on the microhardness and elastic modulus were investigated. The variability and distribution of the microhardness and elastic modulus data were statistically analysed using the Weibull modulus distribution. The results indicate that the dependence of microhardness and elastic modulus on the indentation angle exhibits a parabolic shape. Dependence of the microhardness values on the indentation angle follows Pythagoras's theorem. The microhardness, Weibull modulus of microhardness and Weibull modulus of elastic modulus reach their maximum at the central position (175 µm) on the cross section of the coatings. The Weibull modulus of microhardness revealed similar values throughout the thickness, and the Weibull modulus of elastic modulus shows higher values on the top surface compared to the cross section.

  7. The Structure and Behavior of Vacuum Plasma Sprayed Overlay Coatings on Nickel Based Superalloys.

    Science.gov (United States)

    1983-06-01

    the oxide -1c the coating. SEA, 85 deg. tilt, 5000X B.30 Dee etched NiCrAl with La which shows no . . 45 uicfc-peg formation. S2, 85 deg. tilt, 50001...34 - ’. . - - .. ., - . . - . - ., . - " - ’ .. . ’ . . - - - . . - . 3:11. IIIULU. An ID PL SM2 ,I- 10 iINSOLIZS .U ainUSUL! ’,’ a. Vendor "IN The structures of both the NiCrAl and CcCrAl type...surface and loose particles exhibited by a pl~asma sprayed NiCrAl cocit.ng. * SEE, 1000X Figure B.13 Plasma s Frayed coating by Vendor "B" with low ir

  8. Investigation of Plasma Spray Coatings as an Alternative to Hard Chrome Plating on Internal Surfaces

    Science.gov (United States)

    2006-09-14

    alloy Ni-988 Praxair WC-Co self fluxing 50%(WC 12Co) 50%(33Ni 9Cr 3.5Fe 2Si 2B 0.5C) SM 5803 Sulzer Metco (WC 12Co) 25(Ni-Based Superalloy ) SM...Micro Hardness [HV0.3] Cracks 10012402-1 SM 5803 (WC 12Co) 25(Ni-Based Superalloy ) Ar/He/H2 5.3 82.2 671 Micro cracks 10012502-1 D2002 (WC...o n V o lu m e L o ss ( m m 3 ) Figure 4-28. Abrasion resistance of EHC and plasma spray coatings. Ring Coated (block) disc Figure

  9. Titanium carbonitride thick coating prepared by plasma spray synthesis and its tribological properties

    Institute of Scientific and Technical Information of China (English)

    ZHU Lin; HE JiNing; YAN DianRan; XIAO LiSong; DONG YanChun; XUE DingChuan; MENG DeLiang

    2007-01-01

    TiCN coating,owing to its superior wear-resistance,has been frequently applied in many fields. TiCN thick coating was first prepared by reactive plasma spraying. The phase composition,microstructure and tribological properties of the TiCN coating were investigated in this research. Experimental results show that the microstructure of the TiCN coating was quite dense,and there was also a little amount of titanium oxides within the coating. By XPS analysis,Ti-C and Ti-N bonds were detected in the coating. The TiCN coating exhibited superior wear-resistance. The failure mechanism was attributed to the adhesive wear,the grinding of TiCN hard-grain,as well as the coating failure by oxidation. There were more Fe,Cr,O,etc. in the failure zone,suggesting that the corrosion propagated gradually from surface to interior.

  10. Plasma-sprayed thermal barrier coatings: numerical study on damage localization and evolution

    Directory of Open Access Journals (Sweden)

    K. Slámečka

    2016-01-01

    Full Text Available Thermal barrier coatings (TBCs are advanced material systems used to enhance performance and in-service life of components operated at high temperatures in gas turbines and other power-generation devices. Because of complexity, numerical methods became important tools both for design of these coatings and for in-service life estimations and optimization. In this contribution, two main features that affect the TBCs’ performance, namely the roughness of the bond coat and the microstructure of the ceramic top coat, are discussed based on Finite Element Method (FEM and Finite Element Microstructure MEshfree (FEMME simulations that were used to calculate stresses and assess damage within the coating. Roughness data obtained from plasma-sprayed CoNiCrAlY + YSZ coated samples are supplemented to discuss assumptions and results of employed numerical models.

  11. Preparation and characterization of molybdenum disilicide coating on molybdenum substrate by air plasma spraying

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Yi [Key Laboratory of Ministry of Education for Non-ferrous Materials Science and Engineering, Central South University, Changsha 410083 (China); Key Laboratory of Hunan Province for Metallurgy and Material Processing of Rare Metals, Central South University, Changsha 410083 (China); School of Materials Science and Engineering, Central South University, Changsha 410083 (China); Wang, Dezhi, E-mail: dzwang68@163.com [Key Laboratory of Ministry of Education for Non-ferrous Materials Science and Engineering, Central South University, Changsha 410083 (China); Key Laboratory of Hunan Province for Metallurgy and Material Processing of Rare Metals, Central South University, Changsha 410083 (China); School of Materials Science and Engineering, Central South University, Changsha 410083 (China); Yan, Jianhui [Advanced Materials Synthesis and Application Technology Laboratory, Hunan University of Science and Technology, Xiangtan 411201 (China); Sun, Aokui [Key Laboratory of Ministry of Education for Non-ferrous Materials Science and Engineering, Central South University, Changsha 410083 (China); Key Laboratory of Hunan Province for Metallurgy and Material Processing of Rare Metals, Central South University, Changsha 410083 (China); School of Materials Science and Engineering, Central South University, Changsha 410083 (China)

    2013-11-01

    MoSi{sub 2} oxidation protective coatings on molybdenum substrate were prepared by air plasma spraying technique (APS). Microstructure, phase composition, porosity, microhardness and bonding strength of the coatings were investigated and determined. Oxidation behavior of the coating at high temperature was also examined. Results show that composition of the coatings is constituted with MoSi{sub 2} and Mo{sub 5}Si{sub 3}, the surface morphology is described as flattened lamellar features, insufficiently flattened protuberance with some degree of surface roughness, a certain quantity of spherical particles, microcracks and pores. Testing results reveal that microhardness and bonding strength of the coatings increase, and porosity decreases with increasing power or decreasing Ar gas flow rate. Moreover, with decreasing the porosity, the microhardness of the coatings increases. The bonding strength of the coatings also increases with increasing spray distance. The MoSi{sub 2} coated Mo substrate exhibited a good oxidation resistance at 1200 °C.

  12. Repulsive Interaction of Sulfide Layers on Compressor Impeller Blades Remanufactured Through Plasma Spray Welding

    Science.gov (United States)

    Chang, Y.; Zhou, D.; Wang, Y. L.; Huang, H. H.

    2016-12-01

    This study investigated the repulsive interaction of sulfide layers on compressor impeller blades remanufactured through plasma spray welding (PSW). Sulfide layers on the blades made of FV(520)B steel were prepared through multifarious corrosion experiments, and PSW was utilized to remanufacture blade specimens. The specimens were evaluated through optical microscopy, scanning electron microscopy, energy-dispersive spectroscopy, 3D surface topography, x-ray diffraction, ImageJ software analysis, Vicker's micro-hardness test and tensile tests. Results showed a large number of sulfide inclusions in the fusion zone generated by sulfide layers embodied into the molten pool during PSW. These sulfide inclusions seriously degraded the mechanical performance of the blades remanufactured through PSW.

  13. Comparative Evaluation of Osseointegration of Dental Endodontic Implants with and without Plasma- Sprayed Hydroxy apatite Coating

    Directory of Open Access Journals (Sweden)

    Moosavi SB

    2001-05-01

    Full Text Available Bone osseointegration around dental implant can cause earlier stabilization and fixation of implant and reduce healing time. Hydroxyapatite coating can affect bone osseointegration and enhance its rates. The aim of this study was comparison of osseointegration between plasma sprayed hydroxyapatite coated and uncoated dental implants in cats. Four endodontic implants including, vitallium and two stainless steel with and without hydroxyapatite coating were prepared and placed in mandibular canines of 20 cats after completion of root canal treatment and osseous preparation. After a healing period of 4 months, investigation by scanning electron microscopy showed significant difference in ossointegration between coated and uncoated dental implants and average bone osseointegration of coated implants was more than uncoated implants.

  14. Tungsten carbide coatings with different binders prepared by low power plasma spray system

    Institute of Scientific and Technical Information of China (English)

    GAO Yang; M.F.Morks; FU Ying-qing

    2004-01-01

    Thermal spraying of cermet coatings is widely used for protection of machining parts against wear and corrosion. These coatings consist of WC particles in metal binders such as Co, Cr and Ni. Three kinds of WC powders with different metal binders (Co, NiCr and CoCr) were sprayed by low power plasma spray system on Al-Si-Cu alloy substrate. Fundamental aspects of sprayed cermet coatings, including (i) the effects of binder type on the coating structure, (ii) the hardness and (iii) the microstructure, were investigated. All cermet coatings have the same phase structure such as WC and W2 C. However, the intensities of these phases are different in each coating, mainly due to the difference in solidification rate in each case. Moreover, the hardness measurements are found to be different in each coating. The results show that, binder type has a significant effect on the physical and mechanical properties of the sprayed coatings.

  15. Life Prediction of Atmospheric Plasma-Sprayed Thermal Barrier Coatings Using Temperature-Dependent Model Parameters

    Science.gov (United States)

    Zhang, B.; Chen, Kuiying; Baddour, N.; Patnaik, P. C.

    2017-06-01

    The failure analysis and life prediction of atmospheric plasma-sprayed thermal barrier coatings (APS-TBCs) were carried out for a thermal cyclic process. A residual stress model for the top coat of APS-TBC was proposed and then applied to life prediction. This residual stress model shows an inversion characteristic versus thickness of thermally grown oxide. The capability of the life model was demonstrated using temperature-dependent model parameters. Using existing life data, a comparison of fitting approaches of life model parameters was performed. A larger discrepancy was found for the life predicted using linearized fitting parameters versus temperature compared to those using non-linear fitting parameters. A method for integrating the residual stress was proposed by using the critical time of stress inversion. The role of the residual stresses distributed at each individual coating layer was explored and their interplay on the coating's delamination was analyzed.

  16. Deposition of titanium nitride layers by electric arc - Reactive plasma spraying method

    Energy Technology Data Exchange (ETDEWEB)

    Serban, Viorel-Aurel [University ' Politehnica' of Timisoara, Faculty of Mechanical Engineering, No. 1 Mihai Viteazu Boulevard, 300222 Timisoara (Romania); Rosu, Radu Alexandru, E-mail: raduniz@gmail.com [University ' Politehnica' of Timisoara, Faculty of Mechanical Engineering, No. 1 Mihai Viteazu Boulevard, 300222 Timisoara (Romania); Bucur, Alexandra Ioana [National Institute for Research and Development in Electrochemistry and Condensed Matter Timisoara, Analysis and Characterization Department, No. 1 P Andronescu Street, Timisoara 300224 (Romania); Pascu, Doru Romulus [Romania National Research and Development Institute for Welding and Material Testing Timisoara, No. 30 Mihai Viteazu Boulevard, 300222 Timisoara (Romania)

    2013-01-15

    Highlights: Black-Right-Pointing-Pointer Titanium nitride layers deposited by electric arc - reactive plasma spraying method. Black-Right-Pointing-Pointer Deposition of titanium nitride layers on C45 steel at different spraying distances. Black-Right-Pointing-Pointer Characterization of the coatings hardness as function of the spraying distances. Black-Right-Pointing-Pointer Determination of the corrosion behavior of titanium nitride layers obtained. - Abstract: Titanium nitride (TiN) is a ceramic material which possesses high mechanical properties, being often used in order to cover cutting tools, thus increasing their lifetime, and also for covering components which are working in corrosive environments. The paper presents the experimental results on deposition of titanium nitride coatings by a new combined method (reactive plasma spraying and electric arc thermal spraying). In this way the advantages of each method in part are combined, obtaining improved quality coatings in the same time achieving high productivity. Commercially pure titanium wire and C45 steel as substrate were used for experiments. X-ray diffraction analysis shows that the deposited coatings are composed of titanium nitride (TiN, Ti{sub 2}N) and small amounts of Ti{sub 3}O. The microstructure of the deposited layers, investigated both by optical and scanning electron microscopy, shows that the coatings are dense, compact, without cracks and with low porosity. Vickers microhardness of the coatings presents maximum values of 912 HV0.1. The corrosion tests in 3%NaCl solution show that the deposited layers have a high corrosion resistance compared to unalloyed steel substrate.

  17. Study of the characteristics of plasma spray sealing aluminum silicon-polyester coatings

    Directory of Open Access Journals (Sweden)

    Mihailo R. Mrdak

    2012-07-01

    Full Text Available This study shows the homologation of the plasma spray parameters of soft abrasive AlSi - Polyester seals so that they can be applied on the TV2 - 117A compressor engines. The research has aimed at substituting existing sealants with a new class of materials in order to increase the sealing effect under the highest levels of pressure and to provide the air flow temperature of 100-125°C through the compressor. The Metco 601NS material and plasma spray technology were applied on the air labyrinth ring as a part of the TV2-117A turbojet engine compressor in order to obtain soft sealing. The deposit parameters were carefully selected in order to obtain coatings with the best characteristics depending on their application.The flow of helium was taken as a basic parameter in the parameter selection procedure. The coating with the best mechanical and structural properties was deposited on the air labyrinth ring to examine the effect of the coating application in an assembly. The microstructures of deposited layers were estimated with a light microscope and a (SEM Scanning Electron Microscope. The microstructural analysis of deposited layers was performed according to the Pratt - Whitney standard. The assessment of the mechanical properties of the coatings was done by examining the macrohardness of the sealing layers with the HR15Y method. The coating bond strength was tested by tensile testing. The effect of the air labyrinth ring sealing was tested inside the TV2-117A engine compressor on the test station for a period of 42 hour.

  18. Nanostructured bioactive glass-ceramic coatings deposited by the liquid precursor plasma spraying process

    Science.gov (United States)

    Xiao, Yanfeng; Song, Lei; Liu, Xiaoguang; Huang, Yi; Huang, Tao; Wu, Yao; Chen, Jiyong; Wu, Fang

    2011-01-01

    Bioactive glass-ceramic coatings have great potential in dental and orthopedic medical implant applications, due to its excellent bioactivity, biocompatibility and osteoinductivity. However, most of the coating preparation techniques either produce only thin thickness coatings or require tedious preparation steps. In this study, a new attempt was made to deposit bioactive glass-ceramic coatings on titanium substrates by the liquid precursor plasma spraying (LPPS) process. Tetraethyl orthosilicate, triethyl phosphate, calcium nitrate and sodium nitrate solutions were mixed together to form a suspension after hydrolysis, and the liquid suspension was used as the feedstock for plasma spraying of P 2O 5-Na 2O-CaO-SiO 2 bioactive glass-ceramic coatings. The in vitro bioactivities of the as-deposited coatings were evaluated by soaking the samples in simulated body fluid (SBF) for 4 h, 1, 2, 4, 7, 14, and 21 days, respectively. The as-deposited coating and its microstructure evolution behavior under SBF soaking were systematically analyzed by scanning electron microscopy (SEM), X-ray diffraction (XRD), inductively coupled plasma (ICP), and Fourier transform infrared (FTIR) spectroscopy. The results showed that P 2O 5-Na 2O-CaO-SiO 2 bioactive glass-ceramic coatings with nanostructure had been successfully synthesized by the LPPS technique and the synthesized coatings showed quick formation of a nanostructured HCA layer after being soaked in SBF. Overall, our results indicate that the LPPS process is an effective and simple method to synthesize nanostructured bioactive glass-ceramic coatings with good in vitro bioactivity.

  19. Plasma Sprayed Pour Tubes and Other Melt Handling Components for Use in Gas Atomization

    Energy Technology Data Exchange (ETDEWEB)

    Byrd, David; Rieken, Joel; Heidloff, Andy; Besser, Matthew; Anderson, Iver

    2011-04-01

    Ames Laboratory has successfully used plasma sprayed ceramic components made from yttria stabilized zirconia as melt pouring tubes for gas atomization for many years. These tubes have proven to be strong, thermal shock resistant and versatile. Various configurations are possible both internally and externally. Accurate dimensions are achieved internally with a machined fugitive graphite mandrel and externally by diamond grinding. The previous study of the effect of spray parameters on density was extended to determine the effect of the resulting density on the thermal shock characteristics on down-quenching and up-quenching. Encouraging results also prompted investigation of the use of plasma spraying as a method to construct a melt pour exit stopper that is mechanically robust, thermal shock resistant, and not susceptible to attack by reactive melt additions. The Ames Laboratory operates two close-coupled high pressure gas atomizers. These two atomizers are designed to produce fine and coarse spherical metal powders (5{mu} to 500{mu} diameter) of many different metals and alloys. The systems vary in size, but generally the smaller atomizer can produce up to 5 kg of powder whereas the larger can produce up to 25 kg depending on the charge form and density. In order to make powders of such varying compositions, it is necessary to have melt systems capable of heating and containing the liquid charge to the desired superheat temperature prior to pouring through the atomization nozzle. For some metals and alloys this is not a problem; however for some more reactive and/or high melting materials this can pose unique challenges. Figure 1 is a schematic that illustrates the atomization system and its components.

  20. Effect of steam treatment during plasma spraying on the microstructure of hydroxyapatite splats and coatings

    Science.gov (United States)

    Li, H.; Khor, K. A.; Cheang, P.

    2006-12-01

    The major problems with plasma sprayed hydroxyapatite (HA) coatings for hard tissue replacement are severe HA decomposition and insufficient mechanical properties of the coatings. Loss of crystalline HA after the high-temperature spraying is due mainly to the loss of OH- in terms of water. The current study used steam to treat HA droplets and coatings during both in-flight and flattening stages during plasma spraying. The microstructure of the HA coatings and splats was characterized using scanning electron microscope, Raman spectroscopy, Fourier transform IR spectroscopy, and x-ray diffraction. Results showed that a significant increase in crystallinity of the HA coating was achieved through the steam treatment (e.g., from 58 to 79%). In addition, the effects were dependent on particle sizes of the HA feedstock, more increase in crystallinity of the coatings made from smaller powders was revealed. The Raman spectroscopy analyses on the individual splats and coatings indicate that the mechanism involves entrapping of water molecules by the individual HA droplets upon their impingement. It further suggests that the HA decomposition has already taken place before the impingement of the droplets on precoating or substrate. The improvement in crystallinity and phases, for example, from tricalcium phosphate and amorphous calcium phosphate to HA, was achieved by reversing the HA decomposition through providing extra OH-. Furthermore, the steam treatment during the spraying also accounts for remarkably increased adhesion strength from 9.09 to 23.13 MPa. The in vitro testing through immersing the HA coatings in simulated body fluid gives further evidence that the economic and simple steam treatment is promising in improving HA coating structure.

  1. Effect of Processing Conditions on the Anelastic Behavior of Plasma Sprayed Thermal Barrier Coatings

    Science.gov (United States)

    Viswanathan, Vaishak

    2011-12-01

    Plasma sprayed ceramic materials contain an assortment of micro-structural defects, including pores, cracks, and interfaces arising from the droplet based assemblage of the spray deposition technique. The defective architecture of the deposits introduces a novel "anelastic" response in the coatings comprising of their non-linear and hysteretic stress-strain relationship under mechanical loading. It has been established that this anelasticity can be attributed to the relative movement of the embedded defects under varying stresses. While the non-linear response of the coatings arises from the opening/closure of defects, hysteresis is produced by the frictional sliding among defect surfaces. Recent studies have indicated that anelastic behavior of coatings can be a unique descriptor of their mechanical behavior and related to the defect configuration. In this dissertation, a multi-variable study employing systematic processing strategies was conducted to augment the understanding on various aspects of the reported anelastic behavior. A bi-layer curvature measurement technique was adapted to measure the anelastic properties of plasma sprayed ceramic. The quantification of anelastic parameters was done using a non-linear model proposed by Nakamura et.al. An error analysis was conducted on the technique to know the available margins for both experimental as well as computational errors. The error analysis was extended to evaluate its sensitivity towards different coating microstructure. For this purpose, three coatings with significantly different microstructures were fabricated via tuning of process parameters. Later the three coatings were also subjected to different strain ranges systematically, in order to understand the origin and evolution of anelasticity on different microstructures. The last segment of this thesis attempts to capture the intricacies on the processing front and tries to evaluate and establish a correlation between them and the anelastic

  2. Plasma Sprayed Pour Tubes and Other Melt Handling Components for Use in Gas Atomization

    Energy Technology Data Exchange (ETDEWEB)

    Byrd, David; Rieken, Joel; Heidloff, Andy; Besser, Matthew; Anderson, Iver

    2011-04-01

    Ames Laboratory has successfully used plasma sprayed ceramic components made from yttria stabilized zirconia as melt pouring tubes for gas atomization for many years. These tubes have proven to be strong, thermal shock resistant and versatile. Various configurations are possible both internally and externally. Accurate dimensions are achieved internally with a machined fugitive graphite mandrel and externally by diamond grinding. The previous study of the effect of spray parameters on density was extended to determine the effect of the resulting density on the thermal shock characteristics on down-quenching and up-quenching. Encouraging results also prompted investigation of the use of plasma spraying as a method to construct a melt pour exit stopper that is mechanically robust, thermal shock resistant, and not susceptible to attack by reactive melt additions. The Ames Laboratory operates two close-coupled high pressure gas atomizers. These two atomizers are designed to produce fine and coarse spherical metal powders (5{mu} to 500{mu} diameter) of many different metals and alloys. The systems vary in size, but generally the smaller atomizer can produce up to 5 kg of powder whereas the larger can produce up to 25 kg depending on the charge form and density. In order to make powders of such varying compositions, it is necessary to have melt systems capable of heating and containing the liquid charge to the desired superheat temperature prior to pouring through the atomization nozzle. For some metals and alloys this is not a problem; however for some more reactive and/or high melting materials this can pose unique challenges. Figure 1 is a schematic that illustrates the atomization system and its components.

  3. Stability and phase evolution of mullite in reducing atmosphere

    Energy Technology Data Exchange (ETDEWEB)

    Naghizadeh, R., E-mail: rnaghizadeh@iust.ac.ir; Golestani-fard, F.; Rezaie, H.R.

    2011-05-15

    The aim of this study is to investigate the stability of mullite and its phase evolution when heated at 1600-1650 deg. C in reducing atmosphere created by a carbon bed. The stoichiometric mullite (3Al{sub 2}O{sub 3}.2SiO{sub 2}) was synthesized by reacting the proper precursors at 1400 deg. C in air atmosphere. Samples containing the primary mullite and graphite or carbon were prepared by pressing the mix and heated at 1600-1650 deg. C. Products were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The results showed that the stoichiometric mullite could decompose to corundum and alumina-rich mullite. During firing under reducing atmosphere, the stoichiometric mullite became richer in Al{sup 3+} cations. The gaseous SiO compound was found to be released from the sample and reacting with C to form SiC phase. Comparison of general mullite solid solution (Al{sub 4+2x}Si{sub 2-2x}O{sub 10-x}) with alumina-rich mullite obtained from decomposition revealed that x would take different values depending on temperature and atmosphere. The ultimate decomposition product was found to be corundum. - Research Highlights: {yields} This method is a new route for investigation of thermochemical stability of stoichimetric mullite under reducing condition which have done by the authors. {yields} This research has got very good results for stability of mullite at different conditions. {yields} This work has also studied the mechanism of stability of mullite under reducing atmosphere.

  4. Mullite/Mo interfaces formed by Intrusion bonding

    Energy Technology Data Exchange (ETDEWEB)

    Bartolome, Jose F.; Diaz, Marcos; Moya, Jose S.; Saiz, Eduardo; Tomsia, Antoni P.

    2003-04-30

    The microstructure and strength of Mo/mullite interfaces formed by diffusion bonding at 1650 C has been analyzed. Interfacial metal-ceramic interlocking contributes to flexural strength of approx. 140 MPa as measured by 3 point bending. Saturation of mullite with MoO2 does not affect the interfacial strength.

  5. Processing of fine-diameter continuous mullite fibers

    Energy Technology Data Exchange (ETDEWEB)

    Al-Assafi, S.; Cruse, T.; Simmons, J.H. [Univ. of Florida, Gainesville, FL (United States)] [and others

    1994-12-31

    Fine-diameter, continuous mullite fibers were fabricated by sol-gel processing using two different chelating agents on weight loss behavior, mullite formation, and sintered fiber microstructure were examined. The molar ratio, R, of chelating agent to alumina precursor in the sol was varied in order to optimize continuous spinning conditions. The importance of aging conditions on the sintered fiber density was demonstrated.

  6. Assessment of plasma sprayed coatings to modify surface friction for railroad applications

    Science.gov (United States)

    Davis, Heidi Lynn

    For the past hundred years, railroads have been an important means of transportation for passengers and freight. Over the years train traffic, speeds, and loads have increased steadily leading to a more severe wheel/rail environment that exceeds the design limits of the steels thus causing increased wear, decreased rail life, and higher maintenance costs. The cost of controlling friction and the resulting damage is an area of ever-increasing concern. One potential method of modifying friction is by changing the surface properties of the rail. The work reported herein was carried out as part of a larger effort to modify surface friction of rails. The original focus of this research was to use high velocity air plasma spraying to develop friction enhancing coatings for the rail surface. Using the methodology developed at the Oregon Graduate Institute, the plasma spray parameters were optimized and the coatings were tested on the Amsler machine under rolling/sliding wear conditions to determine viability prior to full scale testing. Stainless steel and composite 1080 steel were investigated as potential materials for increasing friction. Poor results with these coatings shifted the research focus to understanding the durability of the coatings and to failure analysis of initial 1080 steel full scale samples tested by the Facility for Accelerated Service Testing that had failed prematurely. After re-optimization of parameters and preparation methodologies further full scale samples (1080 steel/nylon) were tested and failure analysis was performed. Optical and scanning electron microscopy were used to evaluate the microstructure of coatings from the tested samples. The laboratory scale Amsler test did not appear to be a good indicator of the performance of the coating in full scale tests, because variations in microstructure were caused by differences in sample size, geometry and spraying methods when scaling up from a small Amsler roller to a large rail sample. The

  7. PLASMA SPRAYED Ni-Al COATINGS FOR SAFE ENDING HEAT EXCHANGER TUBES

    Energy Technology Data Exchange (ETDEWEB)

    ALLAN,M.L.; OTTERSON,D.; BERNDT,C.C.

    1998-11-01

    Brookhaven National Laboratory (BNL) has developed thermally conductive composite liners for corrosion and scale protection in heat exchanger tubes exposed to geothermal brine. The liners cannot withstand roller expansion to connect the tubes to the tubesheet. It is not possible to line the ends of the tubes with the same material after roller expansion due to the nature of the current liner application process. It was requested that BNL evaluate plasma sprayed Ni-Al coatings for safe ending heat exchanger tubes exposed to geothermal brine. The tubes of interest had an internal diameter of 0.875 inches. It is not typical to thermal spray small diameter components or use such small standoff distances. In this project a nozzle extension was developed by Zatorski Coating Company to spray the tube ends as well as flat coupons for testing. Four different Ni-Al coatings were investigated. One of these was a ductilized Ni-AIB material developed at Oak Ridge National Laboratory. The coatings were examined by optical and scanning electron microscopy. In addition, the coatings were analyzed by X-ray diffraction and subjected to corrosion, tensile adhesion, microhardness and field tests in a volcanic pool in New Zealand. It was determined that the Ni-Al coatings could be applied to a depth of two inches on the tube ends. When sprayed on flat coupons the coatings exhibited relatively high adhesion strength and microhardness. Polarization curves showed that the coating performance was variable. Measured corrosion potentials indicated that the Ni-Al coatings are active towards steel coated with thermally conductive polymers, thereby suggesting preferential corrosion. Corrosion also occurred on the coated coupons tested in the volcanic pool. This may have been exacerbated by the difficulty in applying a uniform coating to the coupon edges. The Ni-Al coatings applied to the tubes had significant porosity and did not provide adequate corrosion protection. This is associated with

  8. Simulation on change of generic satellite radar cross section via artificially created plasma sprays

    Science.gov (United States)

    Chung, Shen Shou Max; Chuang, Yu-Chou

    2016-06-01

    Recent advancements in antisatellite missile technologies have proven the effectiveness of such attacks, and the vulnerability of satellites in such exercises inspires a new paradigm in RF Stealth techniques suitable for satellites. In this paper we examine the possibility of using artificially created plasma sprays on the surface of the satellite’s main body to alter its radar cross section (RCS). First, we briefly review past research related to RF Stealth using plasma. Next, we discuss the physics between electromagnetic waves and plasma, and the RCS number game in RF Stealth design. A comparison of RCS in a generic satellite and a more complicated model is made to illustrate the effect of the RCS number game, and its meaning for a simulation model. We also run a comparison between finite-difference-time-domain (FDTD) and multilevel fast multipole method (MLFMM) codes, and find the RCS results are very close. We then compare the RCS of the generic satellite and the plasma-covered satellite. The incident radar wave is a differentiated Gaussian monopulse, with 3 dB bandwidth between 1.2 GHz and 4 GHz, and we simulate three kinds of plasma density, with a characteristic plasma frequency ω P  =  0.1, 1, and 10 GHz. The electron-neutral collision frequency ν en is set at 0.01 GHz. We found the RCS of plasma-covered satellite is not necessarily smaller than the originally satellite. When ω P is 0.1 GHz, the plasma spray behaves like a dielectric, and there is minor reduction in the RCS. When ω P is 1 GHz, the X-Y cut RCS increases. When ω P is 10 GHz, the plasma behaves more like a metal to the radar wave, and stronger RCS dependency to frequency appears. Therefore, to use plasma as an RCS adjustment tool requires careful fine-tuning of plasma density and shape, in order to achieve the so-called plasma stealth effect.

  9. On the Anelastic Behavior of Plasma Sprayed Ceramic Coatings: Observations, Characterizations and Applications

    Science.gov (United States)

    Dwivedi, Gopal

    Plasma sprayed ceramic materials contain an assortment of microstructural defects, including pores, cracks, and interfaces arising from the droplet based assemblage of the spray deposition technique. The defective architecture of the deposits introduces a novel "anelastic" response in the coatings comprising of their non-linear and hysteretic stress-strain relationship under mechanical loading. It has been established that this anelasticity can be attributed to the relative movement of the embedded defects under varying stresses; while the non-linear response of the coatings arises from the opening/closure of defects, hysteresis is produced by the frictional sliding among defect surfaces. Recent studies have indicated that anelastic behavior of coatings can be a unique descriptor of their mechanical behavior and related to the defect configuration. In this dissertation, a multi-variable study employing systematic processing strategies was conducted to augment the understanding on various aspects of the reported anelastic behavior. Enhancements to bi-layer curvature measurement technique allowed for reliable and repeatable quantification of the anelastic response, enabling extraction of three anelastic parameters; elastic modulus, non-linear degree and hysteresis degree. This allowed for further exploration of the process space enabling controlled introduction of anelasticity in thermal sprayed ceramic coatings. This dissertation reports on these findings by first describing the experimental advancements in bilayer curvature measurements via thermal cycling of a coated beam. This experimental development allowed assessment of sensitivity and repeatability of the obtained anelastic parameters to varying microstructures imposed by processing excursions. Subsequently, controlled modification of anelasticity was achieved through material and process parameters as well as through extrinsic modification of the defects within the microstructure. The results suggest that

  10. Initial phase hot corrosion mechanism of gas tunnel type plasma sprayed thermal barrier coatings

    Energy Technology Data Exchange (ETDEWEB)

    Yugeswaran, S. [Joining and Welding Research Institute, Osaka University, Osaka 567-0047 (Japan); Kobayashi, A., E-mail: kobayasi@jwri.osaka-u.ac.jp [Joining and Welding Research Institute, Osaka University, Osaka 567-0047 (Japan); Ananthapadmanabhan, P.V. [L and PT Division, Bhabha Atomic Research Centre, Mumbai 400085 (India)

    2012-04-25

    Highlights: Black-Right-Pointing-Pointer Free standing TBC specimens were prepared by gas tunnel type plasma spraying with thickness of around 300-400 {mu}m. Black-Right-Pointing-Pointer 50%8YSZ + 50%La{sub 2}Zr{sub 2}O{sub 7} composite coating shows superior hot corrosion resistance. Black-Right-Pointing-Pointer Corrosive crystals structure and phase transformation was well controlled in this coating. - Abstract: The hot corrosion resistance of the top layer in TBC is one of the main constructive factors which determines the lifetime of the coatings under critical operating environments. In the present study, 8 wt% yttria stabilized zirconia (8YSZ), lanthanum zirconate (La{sub 2}Zr{sub 2}O{sub 7}) and equal weight percentage of its composite (50%8YSZ + 50% La{sub 2}Zr{sub 2}O{sub 7}) coatings were prepared by using gas tunnel type plasma spray torch at optimum spraying conditions. The hot corrosion performances of the above thermal barrier coatings were examined against 40 wt%V{sub 2}O{sub 5}-60 wt%Na{sub 2}SO{sub 4} corrosive ash at 1173 K for 5 h in open air atmosphere. After hot-corrosion testing, the coating surface was studied using a scanning electron microscope to observe the microstructure and X-ray diffraction techniques were used to identify the phase compositions. The results showed that LaVO{sub 4} and YVO{sub 4} are the main hot corrosion products along with the ZrO{sub 2} phase transformation from tetragonal to monoclinic phases in La{sub 2}Zr{sub 2}O{sub 7} and 8YSZ coatings respectively. The microstructure and phase formation mechanism of the hot corrosion products varied with each coating and among these, composition of 50%8YSZ + 50%La{sub 2}Zr{sub 2}O{sub 7} coating exhibited least degradation against V{sub 2}O{sub 5}-Na{sub 2}SO{sub 4} corrosive environment compared to the other coatings.

  11. The influences of heat treatments and interdiffusion on the adhesion of plasma-sprayed NiCrAlY coatings

    Energy Technology Data Exchange (ETDEWEB)

    Richard, C.S. [Universite de Technologie de Compiegne (France). Departement de Genie Mecanique; Beranger, G. [Universite de Technologie de Compiegne (France). Departement de Genie Mecanique; Lu, J. [Universite de Technologie de Troyes, Departement de Genie des Systemes Mecaniques, 10000, Troyes (France); Flavenot, J.F. [Centre Technique des Industries Mecaniques (CETIM), Departement Materiaux, 60306 Senlis (France)

    1996-07-01

    Most coatings are applied with a specific aim in mind, such as improving the base material resistance to corrosion or wear, or providing a barrier against high temperatures. These aims can obviously only be achieved if the coating is properly bonded to the substrate. This study is focused on a NiCrAlY metallic bonding layer and its adhesion on to nickel-based superalloy substrate. It also looks at the influence of different spraying methods (atmospheric plasma spraying and vacuum plasma spraying) and the influence of a post-heat treatment on adhesion of the coatings. In order to determine adherence, a Vickers indentation test was performed at the substrate/coating interface. In each case, the residual stresses were evaluated by a step-by-step hole drilling method and these were taken into account in assessing the adhesion parameters. The results were supplemented by a microstructural study of the interface. (orig.)

  12. An Assessment of the Residual Stresses in Low Pressure Plasma Sprayed Coatings on an Advanced Copper Alloy

    Science.gov (United States)

    Raj, S. V.; Ghosn, L. J.; Agarwal, A.; Lachtrupp, T. P.

    2002-01-01

    Modeling studies were conducted on low pressure plasma sprayed (LPPS) NiAl top coat applied to an advanced Cu-8(at.%)Cr-4%Nb alloy (GRCop-84) substrate using Ni as a bond coat. A thermal analysis suggested that the NiAl and Ni top and bond coats, respectively, would provide adequate thermal protection to the GRCop-84 substrate in a rocket engine operating under high heat flux conditions. Residual stress measurements were conducted at different depths from the free surface on coated and uncoated GRCop-84 specimens by x-ray diffraction. These data are compared with theoretically estimated values assessed by a finite element analysis simulating the development of these stresses as the coated substrate cools down from the plasma spraying temperature to room temperature.

  13. Chemical Phase and Valence Studies of Plasma Sprayed Coatings: EDXRD and X-ray Absorption Spectroscopy (XAS) Results

    Science.gov (United States)

    2010-06-01

    powder α-Al2O3 anatase -TiO2 EDXRD –structure nano-alumina/titania feed powder α-Al2O3 anatase -TiO2 cubic-CeO2 cubic-ZrO2 EDXRD –structure ε ε ε ε ε e...Ar, N2 Plasma spray deposition (oxidizing agent) O2 α-Al2O3 anatase -TiO2 Ce3+-O !!! cubic-ZrO2 cubic-Ce4+O2 Inert gas Ar, N2 Plasma spray deposition...H2 (reducing agent) (oxidizing agent) O2 α-Al2O3 anatase -TiO2 Ce3+-O ok? cubic-ZrO2 cubic-Ce4+O2 t2g eg L3 p →d ε continuum d DOS e.g. octahedral

  14. Low Thermal Conductivity Yttria-Stabilized Zirconia Thermal Barrier Coatings Using the Solution Precursor Plasma Spray Process

    Science.gov (United States)

    Jordan, Eric H.; Jiang, Chen; Roth, Jeffrey; Gell, Maurice

    2014-06-01

    The primary function of thermal barrier coatings (TBCs) is to insulate the underlying metal from high temperature gases in gas turbine engines. As a consequence, low thermal conductivity and high durability are the primary properties of interest. In this work, the solution precursor plasma spray (SPPS) process was used to create layered porosity, called inter-pass boundaries, in yttria-stabilized zirconia (YSZ) TBCs. IPBs have been shown to be effective in reducing thermal conductivity. Optimization of the IPB microstructure by the SPPS process produced YSZ TBCs with a thermal conductivity of 0.6 W/mK, an approximately 50% reduction compared to standard air plasma sprayed (APS) coatings. In preliminary tests, SPPS YSZ with IPBs exhibited equal or greater furnace thermal cycles and erosion resistance compared to regular SPPS and commercially made APS YSZ TBCs.

  15. Bulge Testing and Interface Fracture Characterization of Plasma-Sprayed and HIP Bonded Zr Coatings on U-Mo

    Science.gov (United States)

    Hollis, K.; Liu, C.; Leckie, R.; Lovato, M.

    2015-01-01

    Bulge testing using a pressurized fluid to fracture the interface between bonded material layers along with three-dimensional digital image correlation to measure the sample distortion caused by pressurized fluid was applied to plasma-sprayed coatings. The initiation fracture toughness associated with the bonded materials was measured during the testing. The bulge testing of the uranium-molybdenum alloy plasma sprayed with zirconium and clad in aluminum is presented. The initiation fracture toughness was observed to increase with the increasing cathodic arc-cleaning current and the use of alternating polarity transferred arc current. This dependence was linked to the interface composition of oxide and mixed metal phases along with the interface temperature during spray deposition.

  16. High-temperature thermo-mechanical behavior of functionally graded materials produced by plasma sprayed coating: Experimental and modeling results

    Science.gov (United States)

    Choi, Kang Hyun; Kim, Hyun-Su; Park, Chang Hyun; Kim, Gon-Ho; Baik, Kyoung Ho; Lee, Sung Ho; Kim, Taehyung; Kim, Hyoung Seop

    2016-09-01

    Thermal barrier coatings are widely used in aerospace industries to protect exterior surfaces from harsh environments. In this study, functionally graded materials (FGMs) were investigated with the aim to optimize their high temperature resistance and strength characteristics. NiCrAlY bond coats were deposited on Inconel-617 superalloy substrate specimens by the low vacuum plasma spraying technique. Functionally graded Ni-yttria-stabilized zirconia (YSZ) coatings with gradually varying amounts of YSZ (20%-100%) were fabricated from composite powders by vacuum plasma spraying. Heat shield performance tests were conducted using a high- temperature plasma torch. The temperature distributions were measured using thermocouples at the interfaces of the FGM layers during the tests. A model for predicting the temperature at the bond coating-substrate interface was established. The temperature distributions simulated using the finite element method agreed well with the experimental results.

  17. The properties and fracture behavior of ion plasma sprayed TiN coating on stainless steel substrate

    Science.gov (United States)

    Orlova, Dina V.; Goncharenko, Igor M.; Danilov, Vladimir I.; Lobach, Maxim I.; Danilova, Lidiya V.; Shlyakhova, Galina V.

    2015-10-01

    The wear resistance and fracture behavior of ion plasma sprayed TiN coating were studied; the results are presented. The coating was applied to the stainless steel substrate using a vacuum arc method. The samples were tested by active loading. With varying coating thickness, its characteristics were found to change. Multiple cracking would occur in the deformed sample, with fragment borders aligned normal to the extension axis.

  18. Formation and Characterization of Plasma Sprayed Photocatalytic TiO2- ZnO Nano- Compounded Coatings

    Institute of Scientific and Technical Information of China (English)

    Lee Soo Wohn; Aum Ho Sung; Hur Bo Young; Chen Huang

    2004-01-01

    Two kinds of TiO2-ZnO nano-compounded powders aggregated by spray-drying process and evaporation method were used to deposit photocatalytic coatings by atmospheric plasma spraying technique. The phase compositions, morphologies of the agglomerated TiO2-ZnO powders and the as-sprayed coating were characterized using X-ray diffraction (XRD) and field emission scanning electron microscope (FESEM) respectively. Furthermore, roughness measurements were carried out on their surfaces of the plasma sprayed TiO2-ZnO nano-comPounded coatings. Compared with the TiO2ZnO nano-compounded coating deposited from the spray-dried powder, it was found that the TiO2-ZnO nano-compounded coating deposited from the evaporated powder possesses higher anatase phase. It is ascribed to the existing of partially melted or non-melted microstructure in the TiO2-ZnO coating deposited from the evaporated powder. The partially-meltedor non-melted microstructure was retained from the starting agglomerated powder. This microstructure is beneficial to improve the photocatalytic properties of plasma sprayed TiO2-ZnO nano-compounded coatings.

  19. Improving Erosion Resistance of Plasma-Sprayed Ceramic Coatings by Elevating the Deposition Temperature Based on the Critical Bonding Temperature

    Science.gov (United States)

    Yao, Shu-Wei; Yang, Guan-Jun; Li, Cheng-Xin; Li, Chang-Jiu

    2017-09-01

    Interlamellar bonding within plasma-sprayed coatings is one of the most important factors dominating the properties and performance of coatings. The interface bonding between lamellae significantly influences the erosion behavior of plasma-sprayed ceramic coatings. In this study, TiO2 and Al2O3 coatings with different microstructures were deposited at different deposition temperatures based on the critical bonding temperature concept. The erosion behavior of ceramic coatings was investigated. It was revealed that the coatings prepared at room temperature exhibit a typical lamellar structure with numerous unbonded interfaces, whereas the coatings deposited at the temperature above the critical bonding temperature present a dense structure with well-bonded interfaces. The erosion rate decreases sharply with the improvement of interlamellar bonding when the deposition temperature increases to the critical bonding temperature. In addition, the erosion mechanisms of ceramic coatings were examined. The unbonded interfaces in the conventional coatings act as pre-cracks accelerating the erosion of coatings. Thus, controlling interlamellar bonding formation based on the critical bonding temperature is an effective approach to improve the erosion resistance of plasma-sprayed ceramic coatings.

  20. Preparation of Aluminum Coatings by Atmospheric Plasma Spraying and Dry-Ice Blasting and Their Corrosion Behavior

    Science.gov (United States)

    Dong, Shu-Juan; Song, Bo; Zhou, Gen-Shu; Li, Chang-Jiu; Hansz, Bernard; Liao, Han-Lin; Coddet, Christian

    2013-10-01

    Aluminum coating, as an example of spray coating material with low hardness, was deposited by atmospheric plasma spraying while dry-ice blasting was applied during the deposition process. The deposited coatings were characterized in terms of microstructure, porosity, phase composition, and the valence states. The results show that the APS aluminum coatings with dry-ice blasting present a porosity of 0.35 ± 0.02%, which is comparable to the bulk material formed by the mechanical compaction. In addition, no evident oxide has been detected, except for the very thin and impervious oxide layer at the outermost layer. Compared to plasma-sprayed Al coatings without dry-ice blasting, the adhesion increased by 52% for Al substrate using dry-ice blasting, while 25% for steel substrate. Corrosion behavior of coated samples was evaluated in 3.5 wt.% NaCl aqueous using electrochemistry measurements. The electrochemical results indicated that APS Al coating with dry-ice blasting was more resistant to pitting corrosion than the conventional plasma-sprayed Al coating.

  1. Microstructure and mechanical properties of nickel-chrome-bor-silicon layers produced by the atmospheric plasma spray process

    Directory of Open Access Journals (Sweden)

    Mihailo R. Mrdak

    2012-01-01

    Full Text Available This paper analyzes the influence of plasma spray parameters on the microstructure and mechanical properties of NiCrBSi coatings deposited by the atmospheric plasma spray (APS process. The microstructure and mechanical properties of plasma spray coatings are determined by the interaction of plasma ions with powder particles when the rate and temperature of plasma particles are transferred to powder particles. The interaction effect directly depends on the time the powder particles spend in plasma, and that time is defined by the deposition distance for each type of powder, depending on the grain size, melting temperature and specific mass. In order to obtain homogeneous and dense coatings, three distances (70,120 and 170 mm from the substrate were used in the research. The coating of the best structural and mechanical characteristics was remelted and fused to the base in order to obtain a better structure. Self - fluxing NiCrBSi alloys are widely used because of the good resistance of boride, carbide and silicide solid phases to wear and corrosion. The morphology of powder particles was examined in the SEM (Scanning Electron Microscope, while the microstructure of the layers was assessed using a light microscope. The microstructural analysis of the deposited layers was performed in accordance with the Pratt-Whitney standard. The mechanical properties of the layers were assessed by applying the HV0.3 method for microhardness testing and tensile testing was applied to test bond strength.

  2. Research Into Ni-Cr-Si-B Coating Sprayed Onto Aluminium Substrate Using the Method of Plasma Spray

    Directory of Open Access Journals (Sweden)

    Raimonda Lukauskaitė

    2012-12-01

    Full Text Available The article deals with Ni base coatings deposited on aluminium substrate applying the method of plasma spray. The purpose of the conducted research is to improve the physical and mechanical properties of coatings on the surface of aluminium alloy work pieces. Spraying on aluminium alloys encounters serious problems, and therefore this work analyses the ways to make the situation more favourable. Before spraying, the surfaces of substrates were modified employing chemical and mechanical pre-treatment methods. The aim of pre-treating aluminium alloys was to remove oxide layers from the aluminium surface. Coating microstructures and porosity were characterised applying optical microscopy. Differences in the roughness of pre-treated surfaces have been determined referring to profilometry. The paper investigates the influence of the adhesion of plasma spray coatings on aluminium surface pretreatment. Microhardness technique was applied for measuring the hardness of coatings. The study also describes and compares the mechanical properties of Ni base coatings deposited on different pre-treated aluminium substrates using plasma spray.Article in Lithuanian

  3. Research Into Ni-Cr-Si-B Coating Sprayed Onto Aluminium Substrate Using the Method of Plasma Spray

    Directory of Open Access Journals (Sweden)

    Raimonda Lukauskaitė

    2013-02-01

    Full Text Available The article deals with Ni base coatings deposited on aluminium substrate applying the method of plasma spray. The purpose of the conducted research is to improve the physical and mechanical properties of coatings on the surface of aluminium alloy work pieces. Spraying on aluminium alloys encounters serious problems, and therefore this work analyses the ways to make the situation more favourable. Before spraying, the surfaces of substrates were modified employing chemical and mechanical pre-treatment methods. The aim of pre-treating aluminium alloys was to remove oxide layers from the aluminium surface. Coating microstructures and porosity were characterised applying optical microscopy. Differences in the roughness of pre-treated surfaces have been determined referring to profilometry. The paper investigates the influence of the adhesion of plasma spray coatings on aluminium surface pretreatment. Microhardness technique was applied for measuring the hardness of coatings. The study also describes and compares the mechanical properties of Ni base coatings deposited on different pre-treated aluminium substrates using plasma spray.Article in Lithuanian

  4. Characterization of Nanostructured NbSi2 Intermetallic Coatings Obtained by Plasma Spraying of Mechanically Alloyed Powders

    Science.gov (United States)

    Yazdani, Zohreh; Karimzadeh, Fathallah; Abbasi, Mohammad-Hasan

    2015-08-01

    Nanostructured NbSi2 powders plasma sprayed on to Ti-6Al-4V substrates were characterized in this research. After preparation of the nanostructured NbSi2 powders by mechanical alloying of an Nb-Si powder mixture, agglomeration was performed to obtain a particle size suitable for spraying. The agglomerated powders were then sprayed by atmospheric plasma spraying. Structural transformation of the powders and morphological and mechanical changes of the coatings were examined by use of x-ray diffraction analysis, scanning electron microscopy, energy dispersive spectroscopy, and microhardness testing. During milling, NbSi2 intermetallic with a grain size of approximately 15 nm was gradually formed. After plasma spraying, a coating of hardness 550 ± 8 HV with a uniform nanocrystalline structure, low oxide content, low porosity, and a good adhesion to the substrate was obtained. No phase change occurred after spraying and the NbSi2 compound remained nanostructured with a grain size of approximately 82 nm.

  5. The effect of thermal aging on the thermal conductivity of plasma sprayed and EB-PVD thermal barrier coatings

    Energy Technology Data Exchange (ETDEWEB)

    Dinwiddie, R.B.; Beecher, S.C.; Porter, W.D. [Oak Ridge National Lab., TN (United States); Nagaraj, B.A. [General Electric Co., Cincinnati, OH (United States). Aircraft Engine Group

    1996-05-01

    Thermal barrier coatings (TBCs) applied to the hot gas components of turbine engines lead to enhanced fuel efficiency and component reliability. Understanding the mechanisms which control the thermal transport behavior of the TBCs is of primary importance. Electron beam-physical vapor deposition (EV-PVD) and air plasma spraying (APS) are the two most commonly used coating techniques. These techniques produce coatings with unique microstructures which control their performance and stability. The density of the APS coatings was controlled by varying the spray parameters. The low density APS yttria-partially stabilized zirconia (yttria-PSZ) coatings yielded a thermal conductivity that is lower than both the high density APS coatings and the EB-PVD coatings. The thermal aging of both fully and partially stabilized zirconia are compared. The thermal conductivity of the coatings permanently increases upon exposure to high temperatures. These increases are attributed to microstructural changes within the coatings. This increase in thermal conductivity can be modeled using a relationship which depends on both the temperature and time of exposure. Although the EB-PVD coatings are less susceptible to thermal aging effects, results suggest that they typically have a higher thermal conductivity than APS coatings before thermal aging. The increases in thermal conductivity due to thermal aging for plasma sprayed partially stabilized zirconia have been found to be less than for plasma sprayed fully stabilized zirconia coatings.

  6. Plasma Sprayed Dense MgO-Y2O3 Nanocomposite Coatings Using Sol-Gel Combustion Synthesized Powder

    Science.gov (United States)

    Wang, Jiwen; Jordan, Eric H.; Gell, Maurice

    2010-09-01

    MgO-Y2O3 nanostructured composite powder (volume ratio of 50:50) was synthesized by a sol-gel combustion process which generated crystal sizes in the 10-20 nm range. The MgO-Y2O3 nanopowder was plasma sprayed using a conventional, DC arc plasma spray system. X-ray diffraction analysis shows that the as-sprayed MgO-Y2O3 coating is composed of cubic MgO and Y2O3 phases and has ~95% density. Microstructure characterization by SEM reveals that the as-sprayed coating has fine grain sizes of 100-300 nm as a result of rapid solidification. The hardness of the coating, 7.5 ± 0.6 GPa, is higher than that of coarse-grained, dense MgO, and Y2O3 ceramics. This approach demonstrates the potential of plasma spray processes for making thick, dense MgO-Y2O3 nanocomposite performs for applications as durable, infrared windows.

  7. Understanding the Formation of Limited Interlamellar Bonding in Plasma Sprayed Ceramic Coatings Based on the Concept of Intrinsic Bonding Temperature

    Science.gov (United States)

    Yao, Shu-Wei; Tian, Jia-Jia; Li, Chang-Jiu; Yang, Guan-Jun; Li, Cheng-Xin

    2016-12-01

    Interlamellar bonding is an important factor controlling the mechanical, thermal and electrical properties of plasma sprayed ceramic coatings. In order to understand the formation of limited interlamellar bonding, a theoretical model is proposed based on the concept of the intrinsic bonding temperature. The numerical simulation of the interface temperature between a molten splat and underlying splats was performed for splats with uniform and non-uniform thickness, in order to reveal the conditions for the interlamellar bonding formation. The interlamellar bonding ratio was theoretically estimated based on the bonding forming conditions. The features of interlamellar bonding revealed by the simulation agree well with the experimental observations. The bonding ratio of plasma sprayed coatings is significantly influenced by the distribution of splat thickness. According to the distribution of Al2O3 splat thickness in the coating, the theoretical estimation of bonding ratio yielded a value of 0.41 for the plasma sprayed Al2O3 coating at the ambient atmosphere conditions, which is reasonably consistent with the observation value. Therefore, the limited interlamellar bonding can be reasonably explained based on the sufficient condition that the maximum interface temperature between a molten splat and underlying splats is larger than the intrinsic bonding temperature.

  8. Supersonic Plasma Spray Deposition of CoNiCrAlY Coatings on Ti-6Al-4V Alloy

    Science.gov (United States)

    Caliari, F. R.; Miranda, F. S.; Reis, D. A. P.; Essiptchouk, A. M.; Filho, G. P.

    2017-06-01

    Plasma spray is a versatile technology used for production of environmental and thermal barrier coatings, mainly in the aerospace, gas turbine, and automotive industries, with potential application in the renewable energy industry. New plasma spray technologies have been developed recently to produce high-quality coatings as an alternative to the costly low-pressure plasma-spray process. In this work, we studied the properties of as-sprayed CoNiCrAlY coatings deposited on Ti-6Al-4V substrate with smooth surface ( R a = 0.8 μm) by means of a plasma torch operating in supersonic regime at atmospheric pressure. The CoNiCrAlY coatings were evaluated in terms of their surface roughness, microstructure, instrumented indentation, and phase content. Static and dynamic depositions were investigated to examine their effect on coating characteristics. Results show that the substrate surface velocity has a major influence on the coating properties. The sprayed CoNiCrAlY coatings exhibit low roughness ( R a of 5.7 μm), low porosity (0.8%), excellent mechanical properties ( H it = 6.1 GPa, E it = 155 GPa), and elevated interface toughness (2.4 MPa m1/2).

  9. Ablation Resistance of C/C Composites with Atmospheric Plasma-Sprayed W Coating

    Science.gov (United States)

    Zhou, Zhe; Wang, Yuan; Gong, Jieming; Ge, Yicheng; Peng, Ke; Ran, Liping; Yi, Maozhong

    2016-12-01

    To improve the ablation resistance of carbon/carbon (C/C) composites, tungsten (W) coating with thickness of 1.2 mm was applied by atmospheric plasma spraying. The antiablation property of the coated composites was evaluated by oxyacetylene flame ablation experiments. The phase composition of the coating was investigated by a combination of x-ray diffraction analysis and scanning electron microscopy with energy-dispersive x-ray spectroscopy analysis. The ablation resistance of the coated C/C substrates was compared with that of uncoated C/C composites and C/C-CuZr composites after ablation for 30 s. The properties of the coated C/C composites after ablation time of 10, 30, 60, 90, 120, and 180 s were further studied. The results indicated that the mass and linear ablation rates of the W-coated C/C composites were lower than those of uncoated C/C or C/C-CuZr composites after ablation for 30 s. The coating exhibited heat stability after 120 s of ablation, with mass loss and linear ablation rates of 7.39 × 10-3 g/s and 3.50 × 10-3 mm/s, respectively. However, the W coating became ineffective and failed after ablation for 180 s. Three ablation regions could be identified, in which the ablation mechanism of the coating changed from thermochemical to thermophysical erosion to mechanical scouring with increasing ablation time.

  10. Preparation of SrZrO3 Thermal Barrier Coating by Solution Precursor Plasma Spray

    Science.gov (United States)

    Li, Xinhui; Ma, Wen; Wen, Jing; Bai, Yu; Sun, Li; Chen, Baodong; Dong, Hongying; Shuang, Yingchai

    2017-02-01

    The solution precursor plasma spray (SPPS) process is capable of depositing highly durable thermal barrier coatings (TBCs). In this study, an aqueous chemical precursor feedstock was injected into the plasma jet to deposit SrZrO3 thermal barrier coating on metal substrate. Taguchi design of experiments was employed to optimize the SPPS process. The thermal characteristics and phase evolution of the SrZrO3 precursor, as well as the influence of various spray parameters on the coating deposition rate, microhardness, microstructure, and phase stability, were investigated. The experimental results showed that, at given spray distance, feedstock flow rate, and atomization pressure, the optimized spray parameters were arc current of 600 A, argon flow rate of 40 L/min, and hydrogen flow rate of 10 L/min. The SrZrO3 coating prepared using the optimized spray parameters had single-pass thickness of 6.0 μm, porosity of 18%, and microhardness of 6.8 ± 0.1 GPa. Phase stability studies indicated that the as-sprayed SrZrO3 coating had good phase stability in the temperature range from room temperature to 1400 °C, gradually exhibiting a phase transition from t'-ZrO2 to m-ZrO2 in the SrZrO3 coating at 1450 °C with increasing time, while the SrZrO3 phase did not change.

  11. Processing of AlCoCrFeNiTi high entropy alloy by atmospheric plasma spraying

    Science.gov (United States)

    Löbel, M.; Lindner, T.; Kohrt, C.; Lampke, T.

    2017-03-01

    High Entropy Alloys (HEA) are gaining increasing interest due to their unique combination of properties. Especially the combination of high mechanical strength and hardness with distinct ductility makes them attractive for numerous applications. One interesting alloy system that exhibits excellent properties in bulk state is AlCoCrFeNiTi. A high strength, wear resistance and high-temperature resistance are the necessary requirements for the application in surface engineering. The suitability of blended, mechanically ball milled and inert gas atomized feedstock powders for the development of atmospheric plasma sprayed (APS) coatings is investigated in this study. The ball milled and inert gas atomized powders were characterized regarding their particle morphology, phase composition, chemical composition and powder size distribution. The microstructure and phase composition of the thermal spray coatings produced with different feedstock materials was investigated and compared with the feedstock material. Furthermore, the Vickers hardness (HV) was measured and the wear behavior under different tribological conditions was tested in ball-on-disk, oscillating wear and scratch tests. The results show that all produced feedstock materials and coatings exhibit a multiphase composition. The coatings produced with inert gas atomized feedstock material provide the best wear resistance and the highest degree of homogeneity.

  12. Porosity and surface roughness simulation of nickel-aluminum coating in plasma spray forming

    Institute of Scientific and Technical Information of China (English)

    ZENG Hao-ping; FANG Jian-cheng; XU Wen-ji; ZHAO Zi-yu; WANG Li

    2006-01-01

    As the important evaluation parameters concerning the spray qualities, the porosity and surface roughness of the coatings obtained by thermal spray forming have great influence on their forming accuracy, mechanical properties and service lifetime. But it is difficult to predict or control the two parameters for such a highly nonlinear process. A two-dimensional simulation of coating porosity and surface roughness of nickel-aluminum alloy (Ni-5%Al) in plasma spray forming was presented, which was based on the multi-dimensional statistical behaviors of the droplets as well as the simplification and digitization of the typical splat cross sections. Further analysis involving the influence of the droplet diameters and the scanning velocities of the spray gun on the two parameters was conducted. The simulation and analysis results indicate that the porosity and surface roughness are more influenced by the droplet diameters, but less influenced by the spray gun velocities. The results will provide basis for the prediction or control of coating mechanical properties by depositing parameters.

  13. Material fundamentals and clinical performance of plasma-sprayed hydroxyapatite coatings: a review.

    Science.gov (United States)

    Sun, L; Berndt, C C; Gross, K A; Kucuk, A

    2001-01-01

    The clinical use of plasma-sprayed hydroxyapatite (HA) coatings on metal implants has aroused as many controversies as interests over the last decade. Although faster and stronger fixation and more bone growth have been revealed, the performance of HA-coated implants has been doubted. This article will initially address the fundamentals of the material selection, design, and processing of the HA coating and show how the coating microstructure and properties can be a good predictor of the expected behavior in the body. Further discussion will clarify the major concerns with the clinical use of HA coatings and introduce a comprehensive review concerning the outcomes experienced with respect to clinical practice over the past 5 years. A reflection on the results indicates that HA coatings can promote earlier and stronger fixation but exhibit a durability that can be related to the coating quality. Specific relationships between coating quality and clinical performance are being established as characterization methods disclose more information about the coating.

  14. CHARACTERIZATION OF YTTRIA AND MAGNESIA PARTIALLY STABILIZED ZIRCONIA BIOCOMPATIBLE COATINGS DEPOSITED BY PLASMA SPRAYING

    Directory of Open Access Journals (Sweden)

    Roşu R. A.

    2013-09-01

    Full Text Available Zirconia (ZrO2 is a biocompatible ceramic material which is successfully used in medicine to cover the metallic implants by various methods. In order to avoid the inconvenients related to structural changes which may appear because of the temperature treatment while depositing the zirconia layer over the metallic implant, certain oxides are added, the most used being Y2O3, MgO and CaO. This paper presents the experimental results regarding the deposition of yttria (Y2O3 and magnesia (MgO partially stabilized zirconia layers onto titanium alloy substrate by plasma spraying method. X ray diffraction investigations carried out both on the initial powders and the coatings evidenced the fact that during the thermal spraying process the structure has not been significantly modified, consisting primarily of zirconium oxide with tetragonal structure. Electronic microscopy analyses show that the coatings are dense, uniform and cracks-free. Adherence tests performed on samples whose thickness ranges between 160 and 220 μm showed that the highest value (23.5 MPa was obtained for the coating of ZrO2 - 8 wt. % Y2O3 with 160 μm thickness. The roughness values present an increasing tendency with increasing the coatings thickness.

  15. Deposition of titanium nitride layers by electric arc - Reactive plasma spraying method

    Science.gov (United States)

    Şerban, Viorel-Aurel; Roşu, Radu Alexandru; Bucur, Alexandra Ioana; Pascu, Doru Romulus

    2013-01-01

    Titanium nitride (TiN) is a ceramic material which possesses high mechanical properties, being often used in order to cover cutting tools, thus increasing their lifetime, and also for covering components which are working in corrosive environments. The paper presents the experimental results on deposition of titanium nitride coatings by a new combined method (reactive plasma spraying and electric arc thermal spraying). In this way the advantages of each method in part are combined, obtaining improved quality coatings in the same time achieving high productivity. Commercially pure titanium wire and C45 steel as substrate were used for experiments. X-ray diffraction analysis shows that the deposited coatings are composed of titanium nitride (TiN, Ti2N) and small amounts of Ti3O. The microstructure of the deposited layers, investigated both by optical and scanning electron microscopy, shows that the coatings are dense, compact, without cracks and with low porosity. Vickers microhardness of the coatings presents maximum values of 912 HV0.1. The corrosion tests in 3%NaCl solution show that the deposited layers have a high corrosion resistance compared to unalloyed steel substrate.

  16. Surface characterization and cytotoxicity analysis of plasma sprayed coatings on titanium alloys.

    Science.gov (United States)

    Rahman, Zia Ur; Shabib, Ishraq; Haider, Waseem

    2016-10-01

    In the realm of biomaterials, metallic materials are widely used for load bearing joints due to their superior mechanical properties. Despite the necessity for long term metallic implants, there are limitations to their prolonged use. Naturally, oxides of titanium have low solubilities and form passive oxide film spontaneously. However, some inclusion and discontinuity spots in oxide film make implant to adopt the decisive nature. These defects heighten the dissolution of metal ions from the implant surface, which results in diminishing bio-integration of titanium implant. To increase the long-term metallic implant stability, surface modifications of titanium alloys are being carried out. In the present study, biomimetic coatings of plasma sprayed hydroxyapatite and titanium were applied to the surface of commercially pure titanium and Ti6Al4V. Surface morphology and surface chemistry were studied using scanning electron microscopy and X-ray photoelectron spectroscopy, respectively. Cyclic potentiodynamic polarization and electrochemical impedance spectroscopy were carried out in order to study their electrochemical behavior. Moreover, cytotoxicity analysis was conducted for osteoblast cells by performing MTS assay. It is concluded that both hydroxyapatite and titanium coatings enhance corrosion resistance and improve cytocompatibility.

  17. Cytotoxicity study of plasma-sprayed hydroxyapatite coating on high nitrogen austenitic stainless steels.

    Science.gov (United States)

    Ossa, C P O; Rogero, S O; Tschiptschin, A P

    2006-11-01

    Stainless steel has been frequently used for temporary implants but its use as permanent implants is restricted due to its low pitting corrosion resistance. Nitrogen additions to these steels improve both mechanical properties and corrosion resistance, particularly the pitting and crevice corrosion resistance. Many reports concerning allergic reactions caused by nickel led to the development of nickel free stainless steel; it has excellent mechanical properties and very high corrosion resistance. On the other hand, stainless steels are biologically tolerated and no chemical bonds are formed between the steel and the bone tissue. Hydroxyapatite coatings deposited on stainless steels improve osseointegration, due their capacity to form chemical bonds (bioactive fixation) with the bone tissue. In this work hydroxyapatite coatings were plasma-sprayed on three austenitic stainless steels: ASTM-F138, ASTM-F1586 and the nickel-free Böhler-P558. The coatings were analyzed by SEM and XDR. The cytotoxicity of the coatings/steels was studied using the neutral red uptake method by quantitative evaluation of cell viability. The three uncoated stainless steels and the hydroxyapatite coated Böhler-P558 did not have any toxic effect on the cell culture. The hydroxyapatite coated ASTM-F138 and ASTM-F1586 stainless steels presented cytotoxicity indexes (IC50%) lower than 50% and high nickel contents in the extracts.

  18. Plasma Sprayed Ni-Al Coatings for Safe Ending Heat Exchanger Tubes

    Energy Technology Data Exchange (ETDEWEB)

    Allen, M.L.; Berndt, C.C.; Otterson, D.

    1998-11-01

    Brookhaven National Laboratory (BNL) has developed thermally conductive composite liners for corrosion and scale protection in heat exchanger tubes exposed to geothermal brine. The liners cannot withstand roller expansion to connect the tubes to the tubesheet. It is not possible to line the ends of the tubes with the same material after roller expansion due to the nature of the current liner application process. It was requested that BNL evaluate plasma sprayed Ni-Al coatings for safe ending heat exchanger tubes exposed to geothermal brine. The tubes of interest had an internal diameter of 0.875 inches. It is not typical to thermal spray small diameter components or use such small standoff distances. In this project a nozzle extension was developed by Zatorski Coating Company to spray the tube ends as well as flat coupons for testing. Four different Ni-Al coatings were investigated. One of these was a ductilized Ni-AlB material developed at Oak Ridge National Laboratory. The coatings were examined by optical and scanning electron microscopy. In addition, the coatings were analyzed by X-ray diffraction and subjected to corrosion, tensile adhesion, microhardness and field tests in a volcanic pool in New Zealand.

  19. Studies on Nanocrystalline TiN Coatings Prepared by Reactive Plasma Spraying

    Directory of Open Access Journals (Sweden)

    Dong Yanchun

    2008-01-01

    Full Text Available Titanium nitride (TiN coatings with nanostructure were prepared on the surface of 45 steel (Fe-0.45%C via reactive plasma spraying (denoted as RPS Ti powders using spraying gun with self-made reactive chamber. The microstructural characterization, phases constitute, grain size, microhardness, and wear resistance of TiN coatings were systematically investigated. The grain size was obtained through calculation using the Scherrer formula and observed by TEM. The results of X-ray diffraction and electron diffraction indicated that the TiN is main phase of the TiN coating. The forming mechanism of the nano-TiN was characterized by analyzing the SEM morphologies of surface of TiN coating and TiN drops sprayed on the surface of glass, and observing the temperature and velocity of plasma jet using Spray Watch. The tribological properties of the coating under nonlubricated condition were tested and compared with those of the AISI M2 high-speed steel and Al2O3 coating. The results have shown that the RPS TiN coating presents better wear resistance than the M2 high-speed steel and Al2O3 coating under nonlubricated condition. The microhardness of the cross-section and longitudinal section of the TiN coating was tested. The highest hardness of the cross-section of TiN coating is 1735.43HV100 g.

  20. A simplified analytical model for dc plasma spray torch: influence of gas properties and experimental conditions

    Science.gov (United States)

    Rat, V.; Coudert, J. F.

    2006-11-01

    A simplified analytical model is proposed to evaluate some characteristics of the arc jet generated with a dc plasma torch, in the restricted area of atmospheric plasma spraying conditions. The plasma inside the anode nozzle is considered as stationary and is divided into the arc column and a surrounding cold layer which electrically insulates the plasma from the nozzle wall. Radiation and processes related to the arc attachment at the electrodes are not explicitly taken into account. Heat conduction is evaluated by using Kirchoff's potential, which is described, as it is done also for the electrical conductivity, as a function of the gas specific enthalpy instead of temperature. The model is used to calculate the specific enthalpy radial distribution. From that, and by introducing a mean isentropic coefficient, it is possible to calculate the axial velocity of the plasma jet at the nozzle exit and to evaluate the different pressure contributions. The comparison between predicted and previously measured plasma jet velocities shows good agreement for various experimental conditions.

  1. Suspension Plasma Spray Fabrication of Nanocrystalline Titania Hollow Microspheres for Photocatalytic Applications

    Science.gov (United States)

    Ren, Kun; Liu, Yi; He, Xiaoyan; Li, Hua

    2015-10-01

    Hollow inorganic microspheres with controlled internal pores in close-cell configuration are usually constructed by submicron-sized particles. Fast and efficient large-scale production of the microspheres with tunable sizes yet remains challenging. Here, we report a suspension plasma spray route for making hollow microspheres from nano titania particles. The processing permits most nano particles to retain their physiochemical properties in the as-sprayed microspheres. The microspheres have controllable interior cavities and mesoporous shell of 1-3 μm in thickness. Spray parameters and organic content in the starting suspension play the key role in regulating the efficiency of accomplishing the hollow sphere structure. For the ease of collecting the spheres for recycling use, ferriferous oxide particles were used as additives to make Fe3O4-TiO2 hollow magnetic microspheres. The spheres can be easily recycled through external magnetic field collection after each time use. Photocatalytic anti-bacterial activities of the hollow spheres were assessed by examining their capability of degrading methylene blue and sterilizing Escherichia coli bacteria. Excellent photocatalytic performances were revealed for the hollow spheres, giving insight into their potential versatile applications.

  2. Microstructures and Tribological Properties of Fe-Based Amorphous Metallic Coatings Deposited via Supersonic Plasma Spraying

    Science.gov (United States)

    Zhou, Yang-yang; Ma, Guo-zheng; Wang, Hai-dou; Li, Guo-lu; Chen, Shu-ying; Fu, Bin-guo

    2017-08-01

    The effects of the Ar flow rate and spraying power of a supersonic plasma spraying process on the microstructures and amorphous phase contents of Fe48Cr15Mo14C15B6Y2 amorphous coatings were systematically investigated. The tribological properties of the coatings were evaluated in pin-on-disk mode using a sliding tribometer. The results show that the amorphous phase content and microhardness initially increase with the Ar flow rate and then gradually decrease. However, the amorphous phase content and microhardness increase with the power. In particular, the amorphous phase content of the coating reaches 96.78% with a spraying power of 62 kW and a 110 L min-1 Ar flow rate. Tribological testing demonstrates that the coatings exhibit similar steady-state coefficients of friction (0.75-0.82) with a total test time of 20 min and an applied load of 20 N. However, the wear rates vary with the spraying parameters. In particular, the relative wear rate of the coating can be enhanced up to sixfold under optimal spraying conditions, resulting in excellent wear resistance. Detailed analysis of the coating wear surfaces indicates that the dominant wear mechanisms are abrasive and oxidative wear. Moreover, delamination may occur during the wear process.

  3. Experimental investigation on erosive wear behaviour of plasma spray coated stainless steel

    Science.gov (United States)

    Girisha, K. G.; Sreenivas Rao, K. V.; Anil, K. C.; Sanman, S.

    2017-04-01

    Slurry erosion is an implicit problem in many engineering industrial components such as ore carrying pipelines, slurry pumps and extruders. Even the water turbine blades are subjected to erosive wear when the water contains considerable amount of silt. In the present study, Al2O3-40%TiO2 powder particles of average particle size of 50 micrometer were deposited on EN56B martenistic stainless steel by atmospheric plasma spray technique. Ni/Cr was pre coated to work as bond coat for good adhesion between coating and the substrate material. A coating thickness of 200 micrometer was achieved. Coated and un-coated substrates were subjected to slurry erosion test as per ASTM G-119 standard. Slurry erosion test rig was used to evaluate the erosion properties at room temperature condition by varying the spindle speed. Scanning electron microphotographs were taken before and after the slurry erosion test. Microstructures reveal uniform distribution of coating materials. Eroded surface shows lip, groove, and crater formation and dense coating resulting in less porosity. Micro hardness test was evaluated and reported. EDX analysis confirms the presence of Al, Ti and O2 particles. It was observed that, Al2O3-40%TiO2 coated substrates exhibit superior erosion resistance as compared to un-coated substrates due to higher hardness and less coating porosity.

  4. Microstructural design of functionally graded coatings composed of suspension plasma sprayed hydroxyapatite and bioactive glass.

    Science.gov (United States)

    Cattini, Andrea; Bellucci, Devis; Sola, Antonella; Pawłowski, Lech; Cannillo, Valeria

    2014-04-01

    Various bioactive glass/hydroxyapatite (HA) functional coatings were designed by the suspension plasma spraying (SPS) technique. Their microstructure, scratch resistance, and apatite-forming ability in a simulated body fluid (SBF) were compared. The functional coatings design included: (i) composite coating, that is, randomly distributed constituent phases; (ii) duplex coating with glass top layer onto HA layer; and (iii) graded coating with a gradual changing composition starting from pure HA at the interface with the metal substrate up to pure glass on the surface. The SPS was a suitable coating technique to produce all the coating designs. The SBF tests revealed that the presence of a pure glass layer on the working surface significantly improved the reactivity of the duplex and graded coatings, but the duplex coating suffered a relatively low scratch resistance because of residual stresses. The graded coating therefore provided the best compromise between mechanical reliability and apatite-forming ability in SBF. © 2013 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 102B: 551-560, 2014.

  5. Characterization of functionally graded hydroxyapatite/titanium composite coatings plasma-sprayed on Ti alloys.

    Science.gov (United States)

    Chen, Chun-Cheng; Huang, Tsui-Hsien; Kao, Chia-Tze; Ding, Shinn-Jyh

    2006-07-01

    Bioceramic coatings like hydroxyapatite (HA) have shown promising bioactive properties in load-bearing implant applications. The aim of this work is to deposit functionally graded HA/Ti layers consisting of an underlying Ti bond coat, the alternating layer, and an HA top-layer on Ti6Al4V substrates using plasma spray to improve the coating-substrate interface properties. The alternating layers were created by means of changing the feeding rate and input power of Ti and HA powders, which gradually decrease Ti content with increasing depth from the Ti bond-coat. The major consideration is to examine the stability of the graded coatings. Experimental results indicated that surface chemistry and morphology of the graded coatings were similar to those of monolithic HA coatings. The bond strength values of the as-sprayed graded coatings were much superior to those of monolithic HA coatings. The cyclic fatigue did have a statistically significant effect on bond strength of monolithic HA coatings, with a decrease of 23%. However, the graded coatings were able to survive 1 million cycles of loading in air without significantly reduced bond strength. The in vitro electrochemical measurement results also indicated that the graded coatings had a more beneficial and desired behavior than monolithic HA coatings after fatigue.

  6. Evaluation and Characterization of Plasma Sprayed Cu Slag-Al Composite Coatings on Metal Substrates

    Directory of Open Access Journals (Sweden)

    S. Mantry

    2013-01-01

    Full Text Available Copper slag is a waste product obtained during matte smelting and refining of copper. The present work explores the coating potential of copper slag by plasma spraying. This work shows that copper slag is eminently coatable. An attempt has been made in the present investigation to use the composites coatings of copper slag and Al powder in suitable combination on aluminium and mild steel substrates in order to improve the surface properties of these ductile metal-alloy substrates. When premixed with Al powder, the coating exhibits higher interfacial adhesion as compared to pure copper slag coatings. Maximum adhesion strengths of about 23 MPa and 21 MPa are recorded for the coatings of copper slag with 15 wt% of Al on aluminium and mild steel substrates, respectively. The input power to the plasma torch is found to affect the coating deposition efficiency and morphology of the coatings. It also suggests value addition of an industrial waste.

  7. Plasma-Powder Feedstock Interaction During Plasma Spray-Physical Vapor Deposition

    Science.gov (United States)

    Anwaar, Aleem; Wei, Lianglinag; Guo, Hongbo; Zhang, Baopeng

    2017-02-01

    Plasma spray-physical vapor deposition is a new process developed to produce coatings from the vapor phase. To achieve deposition from the vapor phase, the plasma-feedstock interaction inside the plasma torch, i.e., from the powder injection point to the nozzle exit, is critical. In this work, the plasma characteristics and the momentum and heat transfer between the plasma and powder feedstock at different torch input power levels were investigated theoretically to optimize the net plasma torch power, among other important factors such as the plasma gas composition, powder feed rate, and carrier gas. The plasma characteristics were calculated using the CEA2 code, and the plasma-feedstock interaction was studied inside the torch nozzle at low-pressure (20-25 kPa) conditions. A particle dynamics model was introduced to compute the particle velocity, coupled with Xi Chen's drag model for nonevaporating particles. The results show that the energy transferred to the particles and the coating morphology are greatly influenced by the plasma gas characteristics and the particle dynamics inside the nozzle. The heat transfer between the plasma gas and feedstock material increased with the net torch power up to an optimum at 64 kW, at which a maximum of 3.4% of the available plasma energy was absorbed by the feedstock powder. Experimental results using agglomerated 7-8 wt.% yttria-stabilized zirconia (YSZ) powder as feedstock material confirmed the theoretical predictions.

  8. Novel Prospects for Plasma Spray-Physical Vapor Deposition of Columnar Thermal Barrier Coatings

    Science.gov (United States)

    Anwaar, Aleem; Wei, Lianglinag; Guo, Qian; Zhang, Baopeng; Guo, Hongbo

    2017-09-01

    Plasma spray-physical vapor deposition (PS-PVD) is an emerging coating technique that can produce columnar thermal barrier coatings from vapor phase. Feedstock treatment at the start of its trajectory in the plasma torch nozzle is important for such vapor-phase deposition. This study describes the effects of the plasma composition (Ar/He) on the plasma characteristics, plasma-particle interaction, and particle dynamics at different points spatially distributed inside the plasma torch nozzle. The results of calculations show that increasing the fraction of argon in the plasma gas mixture enhances the momentum and heat flow between the plasma and injected feedstock. For the plasma gas combination of 45Ar/45He, the total enthalpy transferred to a representative powder particle inside the plasma torch nozzle is highest ( 9828 kJ/kg). Moreover, due to the properties of the plasma, the contribution of the cylindrical throat, i.e., from the feed injection point (FIP) to the start of divergence (SOD), to the total transferred energy is 69%. The carrier gas flow for different plasma gas mixtures was also investigated by optical emission spectroscopy (OES) measurements of zirconium emissions. Yttria-stabilized zirconia (YSZ) coating microstructures were produced when using selected plasma gas compositions and corresponding carrier gas flows; structural morphologies were found to be in good agreement with OES and theoretical predictions. Quasicolumnar microstructure was obtained with porosity of 15% when applying the plasma composition of 45Ar/45He.

  9. Sliding Wear Behavior of Plasma Sprayed Zirconia Coating on Cast Aluminum against Silicon Carbide Ceramic

    Institute of Scientific and Technical Information of China (English)

    Thuong-Hien LE; Young-Hun CHAE; Seock-Sam KIM

    2005-01-01

    The sliding wear behaviors of ZrO2-22 wt pct MgO (MZ) and ZrO2-8 wt pct Y2O3 (YZ) coatings deposited on a cast aluminum alloy with bond layer (NiCrCoAlY) by plasma spray were investigated under dry test conditions at room temperature. Under all load conditions, the wear mechanisms of the MZ and YZ coatings were almost the same.The material transfer and pullout were involved in the wear process of the studied coatings under the test conditions.The wear rate of the MZ coating was less than that of the YZ coating. While increasing the normal load, the wear rates of the MZ and YZ coatings increased. SEM was used to examine the worn surfaces and to elucidate likely wear mechanisms. Energy dispersive X-ray spectroscopy (EDX) analysis of the worn surfaces indicated that material transfer occurred in the direction from the SiC ball to the disk. Fracture toughness had a significant influence on the wear performance of the coatings. It was suggested that the material transfer played an important role in the wear behavior.

  10. Characterization of High-Velocity Single Particle Impacts on Plasma-Sprayed Ceramic Coatings

    Science.gov (United States)

    Kiilakoski, Jarkko; Lindroos, Matti; Apostol, Marian; Koivuluoto, Heli; Kuokkala, Veli-Tapani; Vuoristo, Petri

    2016-08-01

    High-velocity impact wear can have a significant effect on the lifetime of thermally sprayed coatings in multiple applications, e.g., in the process and paper industries. Plasma-sprayed oxide coatings, such as Cr2O3- and TiO2-based coatings, are often used in these industries in wear and corrosion applications. An experimental impact study was performed on thermally sprayed ceramic coatings using the High-Velocity Particle Impactor (HVPI) at oblique angles to investigate the damage, failure, and deformation of the coated structures. The impact site was characterized by profilometry, optical microscopy, and scanning electron microscopy (SEM). Furthermore, the connection between the microstructural details and impact behavior was studied in order to reveal the damage and failure characteristics at a more comprehensive level. Differences in the fracture behavior were found between the thermally sprayed Cr2O3 and TiO2 coatings, and a concept of critical impact energy is presented here. The superior cohesion of the TiO2 coating inhibited interlamellar cracking while the Cr2O3 coating suffered greater damage at high impact energies. The HVPI experiment has proven to be able to produce valuable information about the deformation behavior of coatings under high strain rates and could be utilized further in the development of wear-resistant coatings.

  11. Suspensions Plasma Spraying of Ceramics with Hybrid Water-Stabilized Plasma Technology

    Science.gov (United States)

    Musalek, Radek; Medricky, Jan; Tesar, Tomas; Kotlan, Jiri; Pala, Zdenek; Lukac, Frantisek; Chraska, Tomas; Curry, Nicholas

    2016-12-01

    Technology of water-stabilized plasma torch was recently substantially updated through introduction of a so-called hybrid concept that combines benefits of water stabilization and gas stabilization principles. The high-enthalpy plasma provided by the WSP-H ("hybrid") torch may be used for thermal spraying of powders as well as liquid feedstocks with high feed rates. In this study, results from three selected experiments with suspension plasma spraying with WSP-H technology are presented. Possibility of deposition of coatings with controlled microstructures was demonstrated for three different ceramics (YSZ—yttria-stabilized zirconia, YAG—yttrium aluminum garnet and Al2O3) introduced into ethanol-based suspensions. Shadowgraphy was used for optimization of suspension injection and visualization of the liquid fragmentation in the plasma jet. Coatings were deposited onto substrates attached to the rotating carousel with integrated temperature monitoring and air cooling, which provided an excellent reproducibility of the deposition process. Deposition of columnar-like YSZ and dense YAG and Al2O3 coatings was successfully achieved. Deposition efficiency reached more than 50%, as evaluated according to EN ISO 17 836 standard.

  12. Plasma-Powder Feedstock Interaction During Plasma Spray-Physical Vapor Deposition

    Science.gov (United States)

    Anwaar, Aleem; Wei, Lianglinag; Guo, Hongbo; Zhang, Baopeng

    2017-01-01

    Plasma spray-physical vapor deposition is a new process developed to produce coatings from the vapor phase. To achieve deposition from the vapor phase, the plasma-feedstock interaction inside the plasma torch, i.e., from the powder injection point to the nozzle exit, is critical. In this work, the plasma characteristics and the momentum and heat transfer between the plasma and powder feedstock at different torch input power levels were investigated theoretically to optimize the net plasma torch power, among other important factors such as the plasma gas composition, powder feed rate, and carrier gas. The plasma characteristics were calculated using the CEA2 code, and the plasma-feedstock interaction was studied inside the torch nozzle at low-pressure (20-25 kPa) conditions. A particle dynamics model was introduced to compute the particle velocity, coupled with Xi Chen's drag model for nonevaporating particles. The results show that the energy transferred to the particles and the coating morphology are greatly influenced by the plasma gas characteristics and the particle dynamics inside the nozzle. The heat transfer between the plasma gas and feedstock material increased with the net torch power up to an optimum at 64 kW, at which a maximum of 3.4% of the available plasma energy was absorbed by the feedstock powder. Experimental results using agglomerated 7-8 wt.% yttria-stabilized zirconia (YSZ) powder as feedstock material confirmed the theoretical predictions.

  13. Heat load behaviors of plasma sprayed tungsten coatings on copper alloys with different compliant layers

    Energy Technology Data Exchange (ETDEWEB)

    Chong, F.L. [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei 230031 (China)], E-mail: flch@ipp.ac.cn; Chen, J.L.; Li, J.G. [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei 230031 (China); Hu, D.Y.; Zheng, X.B. [Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai 200051 (China)

    2008-04-15

    Plasma sprayed tungsten (PS-W) coatings with the compliant layers of titanium (Ti), nickel-chromium-aluminum (NiCrAl) alloys and W/Cu mixtures were fabricated on copper alloys, and their properties of the porosity, oxygen content, thermal conductivity and bonding strength were measured. High heat flux tests of actively cooled W coatings were performed by means of an electron beam facility. The results indicated that APS-W coating showed a poorer heat transfer capability and thermo-mechanical properties than VPS-W coating, and the compliant layers improved W coating performance under the heat flux load. Among three compliant layers, W/Cu was the preferable because of its better effects on heat removal and stress alleviating. The optimization of W/Cu compliant layer found that 0.1 mm and 25 vol.%W was optimum compliant layer structure for 1 mm W coating, which induced a 23% reduction of the maximum stress compared to the sharp interface, and the plastic strain was reduced to 0.01% from 1.55%.

  14. Heat load behaviors of plasma sprayed tungsten coatings on copper alloys with different compliant layers

    Science.gov (United States)

    Chong, F. L.; Chen, J. L.; Li, J. G.; Hu, D. Y.; Zheng, X. B.

    2008-04-01

    Plasma sprayed tungsten (PS-W) coatings with the compliant layers of titanium (Ti), nickel-chromium-aluminum (NiCrAl) alloys and W/Cu mixtures were fabricated on copper alloys, and their properties of the porosity, oxygen content, thermal conductivity and bonding strength were measured. High heat flux tests of actively cooled W coatings were performed by means of an electron beam facility. The results indicated that APS-W coating showed a poorer heat transfer capability and thermo-mechanical properties than VPS-W coating, and the compliant layers improved W coating performance under the heat flux load. Among three compliant layers, W/Cu was the preferable because of its better effects on heat removal and stress alleviating. The optimization of W/Cu compliant layer found that 0.1 mm and 25 vol.%W was optimum compliant layer structure for 1 mm W coating, which induced a 23% reduction of the maximum stress compared to the sharp interface, and the plastic strain was reduced to 0.01% from 1.55%.

  15. Rapid Deposition of Titanium Oxide and Zinc Oxide Films by Solution Precursor Plasma Spray

    Science.gov (United States)

    Ando, Yasutaka

    In order to develop a high rate atmospheric film deposition process for functional films, as a basic study, deposition of titanium oxide film and zinc oxide film by solution precursor plasma spray (SPPS) was conducted in open air. Consequently, in the case of titanium oxide film deposition, anantase film and amorphous film as well as rutile film could be deposited by varying the deposition distance. In the case of anatase dominant film, photo-catalytic properties of the films could be confirmed by wettability test. In addition, the dye sensitized sollar cell (DSC) using the TiO2 film deposited by this SPPS technique as photo voltaic device generates 49mV in OCV. On the other hand, in the case of zinc oxide film deposition, it was proved that well crystallized ZnO films with photo catalytic properties could be deposited. From these results, this process was found to have high potential for high rate functional film deposition process conducted in the air.

  16. Thermal Barrier Coatings Made by the Solution Precursor Plasma Spray Process

    Science.gov (United States)

    Gell, Maurice; Jordan, Eric H.; Teicholz, Matthew; Cetegen, Baki M.; Padture, Nitin P.; Xie, Liangde; Chen, Dianying; Ma, Xinqing; Roth, Jeffrey

    2008-03-01

    The solution precursor plasma spray (SPPS) process is a relatively new and flexible thermal spray process that can produce a wide variety of novel materials, including some with superior properties. The SPPS process involves injecting atomized droplets of a precursor solution into the plasma. The properties of resultant deposits depend on the time-temperature history of the droplets in the plasma, ranging from ultra-fine splats to unmelted crystalline particles to unpyrolized particles. By controlling the volume fraction of these three different constituents, a variety of coatings can be produced, all with a nanograin size. In this article, we will be reviewing research related to thermal barrier coatings, emphasizing the processing conditions necessary to obtain a range of microstructures and associated properties. The SPPS process produces a unique strain-tolerant, low-thermal conductivity microstructure consisting of (i) three-dimensional micrometer and nanometer pores, (ii) through-coating thickness (vertical) cracks, (iii) ultra-fine splats, and (iv) inter-pass boundaries. Both thin (0.12 mm) and thick (4 mm) coatings have been fabricated. The volume fraction of porosity can be varied from 10% to 40% while retaining the characteristic microstructure of vertical cracks and ultra-fine splats. The mechanism of vertical crack formation will be described.

  17. Process-Property Relationship for Air Plasma-Sprayed Gadolinium Zirconate Coatings

    Science.gov (United States)

    Dwivedi, Gopal; Tan, Yang; Viswanathan, Vaishak; Sampath, Sanjay

    2015-02-01

    The continuous need of elevating operating temperature of gas turbine engines has introduced several challenges with the current state-of-the-art yttria-stabilized zirconia (YSZ)-based thermal barrier coatings (TBCs), requiring examination of new TBC material with high temperature phase stability, lower thermal conductivity, and resistance to environmental ash particles. Gadolinium zirconate (Gd2Zr2O7) (GDZ) has been shown to meet many of these requirements, and has, in fact, been successfully implemented in to engine components. However, several fundamental issues related to the process-ability, toughness, and microstructural differences for GDZ when compared to equivalent YSZ coating. This study seeks to critically address the process-structure-property correlations for plasma-sprayed GDZ coating subjected to controlled parametric exploration. Use of in-flight diagnostics coupled with in situ and ex situ coating property monitoring allows examination and comparison of the process-property interplay and the resultant differences between the two TBC compositions. The results indicate that it is feasible to retain material chemistry and fabricate relevant microstructures of interest with GDZ with concomitant performance advantages such as low conductivity, mechanical compliance, sintering resistance, and suppression of environmentally induced damage from ash particles. This study provides a framework for optimal design and manufacturing of emergent multi-layer and multi-material TBCs.

  18. Investigation on plasma-sprayed ZrO2 thermal barrier coating on nickel alloy substrate

    Institute of Scientific and Technical Information of China (English)

    卢安贤; 常鹰; 蔡小梅

    2002-01-01

    The thermal barrier coatings with NiCrAlY alloy bonding layer, NiCrAlY-Y2O3 stabilized ZrO2 transition layer and Y2O3 stabilized ZrO2 ceramic layer are prepared on nickel alloy substrates using the plasma spray technique. The relationship among the composition, structure and property of the coatings are investiga-ted by means of optical microscope, scanning electronic microscope and the experiments of thermal shock resistance cycling and high temperature oxidation resistance. The results show that the structure design of introdu-cing a transition layer between Ni alloy substrate and ZrO2 ceramic coating guarantees the high quality and properties of the coatings; ZrO2 coatings doped with a little SiO2 possesses better thermal shock resistance and more excellent hot corrosion resistance as compared with ZrO2 coating materials without SiO2 ;the improvement in performance of ZrO2 coating doped with SiO2 is due to forming more dense coating structure by self- closing effects of the flaws and pores in the ZrO2 coatings.

  19. Investigations on the Nature of Ceramic Deposits in Plasma Spray-Physical Vapor Deposition

    Science.gov (United States)

    He, W.; Mauer, G.; Gindrat, M.; Wäger, R.; Vaßen, R.

    2017-01-01

    In Plasma Spray-Physical Vapor Deposition (PS-PVD) process, major fractions of the feedstock powder can be evaporated so that coatings are deposited mainly from the vapor phase. In this work, Computational Fluid Dynamics (CFD) results indicate that such evaporation occurs significantly in the plasma torch nozzle and even nucleation and condensation of zirconia is highly possible there. Experimental work has been performed to investigate the nature of the deposits in the PS-PVD process, in particular coatings from condensate vapor and nano-sized clusters produced at two spraying distances of 1000 mm and 400 mm. At long spraying distance, columns in the coatings have pyramidal tops and very sharp faceted microstructures. When the spraying distance is reduced to 400 mm, the tops of columns become relatively flat and a faceted structure is not recognizable. XRD patterns show obvious preferred orientations of (110) and (002) in the coatings sprayed at 400 mm but only limited texture in the coatings sprayed at 1000 mm. Meanwhile, a non-line of sight coating was also investigated, which gives an example for pure vapor deposition. Based on these analyses, a vapor and cluster depositions are suggested to further explain the formation mechanisms of high-quality columnar-structured PS-PVD thermal barrier coatings which have already shown excellent performance in cyclic lifetime test.

  20. Highly Segmented Thermal Barrier Coatings Deposited by Suspension Plasma Spray: Effects of Spray Process on Microstructure

    Science.gov (United States)

    Chen, Xiaolong; Honda, Hiroshi; Kuroda, Seiji; Araki, Hiroshi; Murakami, Hideyuki; Watanabe, Makoto; Sakka, Yoshio

    2016-12-01

    Effects of the ceramic powder size used for suspension as well as several processing parameters in suspension plasma spraying of YSZ were investigated experimentally, aiming to fabricate highly segmented microstructures for thermal barrier coating (TBC) applications. Particle image velocimetry (PIV) was used to observe the atomization process and the velocity distribution of atomized droplets and ceramic particles travelling toward the substrates. The tested parameters included the secondary plasma gas (He versus H2), suspension injection flow rate, and substrate surface roughness. Results indicated that a plasma jet with a relatively higher content of He or H2 as the secondary plasma gas was critical to produce highly segmented YSZ TBCs with a crack density up to 12 cracks/mm. The optimized suspension flow rate played an important role to realize coatings with a reduced porosity level and improved adhesion. An increased powder size and higher operation power level were beneficial for the formation of highly segmented coatings onto substrates with a wider range of surface roughness.

  1. Atmospheric Plasma Spraying of Single Phase Lanthanum Zirconate Thermal Barrier Coatings with Optimized Porosity

    Directory of Open Access Journals (Sweden)

    Georg Mauer

    2016-10-01

    Full Text Available The shortcomings at elevated operation temperatures of the standard material yttria-stabilized zirconia (YSZ for thermal barrier coatings (TBCs have initiated many research activities seeking alternatives. One candidate is the pyrochlore lanthanum zirconate La2Zr2O7 (LZ, which is phase-stable to its melting point. At the same time, it shows a lower thermal conductivity and a lower sintering tendency when compared to YSZ. Because of its low thermal expansion coefficient and poor toughness, it is applied in combination with YSZ in double layer TBC systems. It is the current state of knowledge that LZ is prone to lanthanum depletion if processed by plasma spraying. The process conditions have to be selected carefully to avoid this. Furthermore, the amount and morphology of the coating porosity is essential for a good thermo-mechanical performance. In this work, the development and testing of LZ/YSZ double layer TBC systems is described. Initially, suitable basic parameters (torch, plasma gas composition, and power were tested with respect to coating stoichiometry. Then, microstructures were optimized by adjusting feed rate, spray distance, and by selecting a more appropriate feedstock. Powder particles and coatings were characterized by digital image analysis.

  2. Phase Composition, Microstructure, and Tribological Property of Plasma-Sprayed TiC-BASED Coating

    Science.gov (United States)

    Sun, Shibin; Zou, Zengda; Liu, Xuemei; Shi, Hanchao

    TiC-based wear resistant coating was prepared by plasma spraying using reconstituted composite powders doped with ultra-fine carbide. Phase composition and microstructure of as-sprayed coating were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM) utilizing backscattered imaging mode (BSE), and electron probe micro-analysis. Wear test was performed by using a ring-on-block tester under dry sliding condition. Results show that the coating adheres well to the substrate and no delamination appears. TiC content underwent pronounced reduction because of oxidation, reaction, and physical loss. Reactions between TiC and Mo and probably between dissociated C and Mo lead to the formation of Mo2C. Wear resistance of NiCrMo-TiC coating is about 4-8 times higher than that of substrate under different applied force. This work shed light on the reconstitution of spraying powder doped with ultra-fine reinforce phase particles, and the present results are important for the preparation of nano-doped TiC-based coatings.

  3. Determination of residual stresses within plasma spray coating using Moiré interferometry method

    Science.gov (United States)

    Yi, Jiang; Bin-shi, Xu; Hai-dou, Wang; Ming, Liu; Yao-hui, Lu

    2011-01-01

    In this paper, residual stresses of the Ni-Cr-B-Si coatings prepared by supersonic plasma spray processing were measured by moiré interferometry and X-ray diffraction method. Moiré interferometry method was used in measuring the distribution of residual stresses of the Ni-Cr-B-Si coatings alongside the specimen thickness direction, then the distribution of residual stresses both in the substrate and the coating was also analyzed. Experimental results showed that residual stresses in the coating and the substrate are tensile and compressive separately; residual stresses of the coating are diminished with the increase of the distance from the coating surface and almost zero at the coating-substrate interface; the maximum of compressive residual stresses of the substrate are present to the vicinity of the coating-substrate interface. It could be concluded that residual stresses in the specimen would result from the dismatch of thermophysical properties between the coating and substrate during the spray process, and the distribution of residual stresses of the substrate would be influenced by the sandblasting prior to spraying.

  4. Effect of substrate preheating temperature and coating thickness on residual stress in plasma sprayed hydroxyapatite coating

    Science.gov (United States)

    Tang, Dapei

    2015-07-01

    A thermal-mechanical coupling model was developed based on thermal-elastic- plastic theory according the special process of plasma spraying Hydroxyapatite (HA) coating upon Ti-6Al-4V substrate. On the one hand, the classical Fourier transient heat conduction equation was modified by introducing the effect item of deformation on temperature, on the other hand, the Johnson-Cook model, suitable for high temperature and high strain rate conditions, was used as constitutive equation after considering temperature softening effect, strain hardening effect and strain rate reinforcement effect. Based on the above coupling model, the residual stress field within the HA coating was simulated by using finite element method (FEM). Meanwhile, the substrate preheating temperature and coating thickness on the influence of residual stress components were calculated, respectively. The failure modes of coating were also preliminary analyzed. In addition, in order to verify the reliability of calculation, the material removal measurement technique was applied to determine the residual stress of HA coating near the interface. Some important conclusions are obtained.

  5. Surface laser-glazing of plasma-sprayed thermal barrier coatings

    Energy Technology Data Exchange (ETDEWEB)

    Batista, C. [University of Minho, Physics Department, Campus de Gualtar, 4710-057 Braga (Portugal); Portinha, A. [University of Minho, Physics Department, Campus de Gualtar, 4710-057 Braga (Portugal); Ribeiro, R.M. [University of Minho, Physics Department, Campus de Gualtar, 4710-057 Braga (Portugal)]. E-mail: ricardo@fisica.uminho.pt; Teixeira, V. [University of Minho, Physics Department, Campus de Gualtar, 4710-057 Braga (Portugal); Costa, M.F. [University of Minho, Physics Department, Campus de Gualtar, 4710-057 Braga (Portugal); Oliveira, C.R. [Instituto de Desenvolvimentoe Inovacao Tecnologica (IDIT), 4520-102 Santa Maria da Feira (Portugal); University Lusiada, 4760-108 Vila Nova de Famalicao (Portugal)

    2005-07-15

    Atmospheric plasma-sprayed (APS) ZrO{sub 2}-8%WtY{sub 2}O{sub 3} thermal barrier coatings (TBCs) were subjected to a CO{sub 2} continuous wave laser-glazing process in order to generate an external dense layer produced by different processing parameters. For that purpose, different beam scanning speeds and track overlapping were chosen. Surface roughness has been reduced significantly after laser-glazing. Despite the surface crack network, all laser-glazed specimens presented a fully dense and porous free external layer with a columnar microstructure. Surface cracks along the densified layer were found to have tendency to be oriented in two perpendicular directions, one in the direction of the laser beam travel, the other perpendicular to it. Moreover, the cracks parallel to the beam moving direction are found to be on the overlapping zone, coinciding with the edge of the subsequent track. The cracks along the densified layer are vertical and tend to branch and deviate from the vertical direction within the porous PS coating. The largest overlapping allied to the smallest amount of irradiated energy generated the most uniform layer with the shortest crack branches within the PS coating. For the as-sprayed coating, the XRD results revealed mainly t' non-transformable tetragonal zirconia with a small percentage of residual monoclinic zirconia. All glazed coatings presented only t' non-transformable tetragonal zirconia with some variations on preferable crystal orientation.

  6. High-Temperature Solid Lubricant Coating by Plasma Spraying Using Metal-Metal Clad Powders

    Science.gov (United States)

    Zhang, Tiantian; Lan, Hao; Yu, Shouquan; Huang, Chuanbing; Du, Lingzhong; Zhang, Weigang

    2017-08-01

    NiCr/Ag-Mo composite coating was fabricated by atmospheric plasma spray technology using clad powders as the feedstock. Its tribological properties at variable temperature were evaluated using a ball-on-disk high-temperature tribometer in air. The results showed that compared with NiCr, the NiCr/Ag-Mo composite coating exhibited better lubrication effect and higher wear resistance at all test temperatures, especially above 600 °C. At 800 °C, NiCr/Ag-Mo composite coating showed the lowest friction coefficient of about 0.2 and its corresponding wear rate reached 2.5 × 10-5 mm3/Nm. Characterizations of NiCr/Ag-Mo composite coating revealed that at temperatures below 400 °C, Ag was smeared and spread onto the wear surface, reducing the friction and wear. At temperature above 500 °C, the Ag2MoO4 lubrication film formed by tribo-oxidation significantly improved the coating's lubrication effect and wear resistance.

  7. The low cycle fatigue behavior of a plasma-sprayed coating material

    Science.gov (United States)

    Gayda, J.; Gabb, T. P.; Miner, R. V., Jr.

    1986-01-01

    Single crystal nickel-base superalloys employed in turbine blade applications are often used with a plasma spray coating for oxidation and hot corrosion resistance. These coatings may also affect fatigue life of the superalloy substrate. As part of a large program to understand the fatigue behavior of coated single crystals, fully reversed, total strain controlled fatigue tests were run on a free standing NiCoCrAlY coating alloy, PWA 276, at 0.1 Hz. Fatigue tests were conducted at 650 C, where the NiCoCrAlY alloy has modest ductility, and at 1050 C, where it is extremely ductile, showing tensile elongation in excess of 100 percent. At the lower test temperature, deformation induced disordering softened the NiCoCrAlY alloy, while at the higher test temperature cyclic hardening was observed which was linked to gradual coarsening of the two phase microstructure. Fatigue life of the NiCoCrAlY alloy was significantly longer at the higher temperature. Further, the life of the NiCoCrAlY alloy exceeds that of coated, /001/-oriented PWA 1480 single crystals at 1050 C, but at 650 C the life of the coated crystal is greater than that of the NiCoCrAlY alloy on a total strain basis.

  8. Plasma-Sprayed ZnO/TiO2 Coatings with Enhanced Biological Performance

    Science.gov (United States)

    Zhao, Xiaobing; Peng, Chao; You, Jing

    2017-08-01

    Surface chemical composition and topography are two key factors in the biological performance of implants. The aim of this work is to deposit ZnO/TiO2 composite coatings on the surface of titanium substrates by plasma spraying technique. The effects of the amount of ZnO doping on the microstructure, surface roughness, corrosion resistance, and biological performance of the TiO2 coatings were investigated. The results indicated that the phase composition of the as-sprayed TiO2 coating was mainly rutile. Addition of 10% ZnO into TiO2 coating led to a slight shift of the diffraction peaks to lower angle. Anatase phase and Zn2TiO4 were formed in 20%ZnO/TiO2 and 30%ZnO/TiO2 coatings, respectively. Doping with ZnO changed the topography of the TiO2 coatings, which may be beneficial to enhance their biological performance. All coatings exhibited microsized surface roughness, and the corrosion resistance of ZnO/TiO2 coatings was improved compared with pure TiO2 coating. The ZnO/TiO2 coatings could induce apatite formation on their surface and inhibit growth of Staphylococcus aureus, but these effects were dose dependent. The 20%ZnO/TiO2 coating showed better biological performance than the other coatings, suggesting potential application for bone implants.

  9. Low cycle fatigue behaviour of a plasma-sprayed coating material

    Science.gov (United States)

    Gayda, J.; Gabb, T. P.; Miner, R. V.

    1986-01-01

    Single crystal nickel-base superalloys employed in turbine blade applications are often used with a plasma spray coating for oxidation and hot corrosion resistance. These coatings may also affect fatigue life of the superalloy substrate. As part of a large program to understand the fatigue behavior of coated single crystals, fully reversed, total strain controlled fatigue tests were run on a free standing NiCoCrAlY coating alloy, PWA 276, at 0.1 Hz. Fatigue tests were conducted at 650 C, where the NiCoCrAlY alloy has modest ductility, and at 1050 C, where it is extremely ductile, showing tensile elongation in excess of 100 percent. At the lower test temperature, deformation induced disordering softened the NiCoCrAlY alloy, while at the higher test temperature cyclic hardening was observed which was linked to gradual coarsening of the two phase microstructure. Fatigue life of the NiCoCrAlY alloy was significantly longer at the higher temperature. Further, the life of the NiCoCrAlY alloy exceeds that of coated, /001/-oriented PWA 1480 single crystals at 1050 C but at 650 C the life of the coated crystal is greater than that of the NiCoCrAlY alloy on a total strain basis.

  10. Bilayer Suspension Plasma-Sprayed Thermal Barrier Coatings with Enhanced Thermal Cyclic Lifetime: Experiments and Modeling

    Science.gov (United States)

    Gupta, Mohit; Kumara, Chamara; Nylén, Per

    2017-08-01

    Suspension plasma spraying (SPS) has been shown as a promising process to produce porous columnar strain tolerant coatings for thermal barrier coatings (TBCs) in gas turbine engines. However, the highly porous structure is vulnerable to crack propagation, especially near the topcoat-bondcoat interface where high stresses are generated due to thermal cycling. A topcoat layer with high toughness near the topcoat-bondcoat interface could be beneficial to enhance thermal cyclic lifetime of SPS TBCs. In this work, a bilayer coating system consisting of first a dense layer near the topcoat-bondcoat interface followed by a porous columnar layer was fabricated by SPS using Yttria-stabilised zirconia suspension. The objective of this work was to investigate if the bilayer topcoat architecture could enhance the thermal cyclic lifetime of SPS TBCs through experiments and to understand the effect of the column gaps/vertical cracks and the dense layer on the generated stresses in the TBC during thermal cyclic loading through finite element modeling. The experimental results show that the bilayer TBC had significantly higher lifetime than the single-layer TBC. The modeling results show that the dense layer and vertical cracks are beneficial as they reduce the thermally induced stresses which thus increase the lifetime.

  11. High Temperature Multilayer Environmental Barrier Coatings Deposited Via Plasma Spray-Physical Vapor Deposition

    Science.gov (United States)

    Harder, Bryan James; Zhu, Dongming; Schmitt, Michael P.; Wolfe, Douglas E.

    2014-01-01

    Si-based ceramic matrix composites (CMCs) require environmental barrier coatings (EBCs) in combustion environments to avoid rapid material loss. Candidate EBC materials have use temperatures only marginally above current technology, but the addition of a columnar oxide topcoat can substantially increase the durability. Plasma Spray-Physical Vapor Deposition (PS-PVD) allows application of these multilayer EBCs in a single process. The PS-PVD technique is a unique method that combines conventional thermal spray and vapor phase methods, allowing for tailoring of thin, dense layers or columnar microstructures by varying deposition conditions. Multilayer coatings were deposited on CMC specimens and assessed for durability under high heat flux and load. Coated samples with surface temperatures ranging from 2400-2700F and 10 ksi loads using the high heat flux laser rigs at NASA Glenn. Coating morphology was characterized in the as-sprayed condition and after thermomechanical loading using electron microscopy and the phase structure was tracked using X-ray diffraction.

  12. Preparation of Porous Mullite Composite by Microwave Sintering

    Institute of Scientific and Technical Information of China (English)

    FAN Bingbing; ZHANG Rui; SUN Bing; LI Xuqin; LI Chunguang

    2012-01-01

    Microwave sintering method was carried out to prepare porous mullite composite.An insulation structure based on hybrid heating mode was well designed with the wall of mullite and the aided heaters of SiC.The obtained samples were characterized by XRD analysis,apparent porosity detection,and bending strength measurement.SEM was used to observe the microstructure of the sample.It is found that the porous mullite composite could be prepared through the microwave sintering within 2 h at relatively low temperatures around 1000 ℃.The lasted samples show comparatively superior properties to the products prepared by conventional processing.

  13. Mullite fibres preparation by aqueous sol-gel process and activation energy of mullitization

    Energy Technology Data Exchange (ETDEWEB)

    Tan Hongbin, E-mail: hb-t@163.co [State Key Laboratory for Mechanical Behavior of Materials, Xi' an Jiaotong University Xi' an 710049 (China) and School of Materials Science and Engineering, Shaanxi University of Technology, Hanzhong, Shaanxi 723003 (China); Ding Yaping; Yang Jianfeng [State Key Laboratory for Mechanical Behavior of Materials, Xi' an Jiaotong University Xi' an 710049 (China)

    2010-03-04

    Mullite fibres were prepared by sol-gel process using aluminum carboxylates (ACs) and silica sol. ACs was synthesized from dissolving aluminum powder in a mixture of formic acid and oxalic acid using aluminum chloride hexahydrate as catalyst. A molar ratio of 1:2:1 for aluminum, formic acid and oxalic acid was optimized to obtain clear solution and viscous ACs sol for fibres synthesis. Thermogravimetry-differential scanning calorimetry (TG-DSC), Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD), and scanning electron microscopy (SEM) analysis were used to characterize the properties of the gel and ceramic fibres. The gel fibres completely transformed to mullite at 1200 {sup o}C, with a smooth surface and uniform diameter. The activation energy for mullite formation in precursor gel fibres was determined by means of differential thermal analysis. The value obtained, E{sub a} = 741.4 kJ/mol, was lower than most data reported in the literatures, which was attributed to the silica-alumina micro-phase separation when organic acids decomposed during gel fibres heating.

  14. Thermal degradation of fiber coatings in mullite-fiber-reinforced mullite composites

    Energy Technology Data Exchange (ETDEWEB)

    Schmuecker, M.; Schneider, H. [German Aerospace Research Establishment, Koeln (Germany). Inst. for Materials Research; Chawla, K.K.; Xu, Z.R. [New Mexico Inst. of Mining and Technology, Socorro, NM (United States). Dept. of Materials and Metallurgical Engineering

    1997-08-01

    The thermal degradation behavior of single-layer BN and of double-layer BN/SiC chemically vapor-deposited fiber coatings in mullite-fiber-reinforced mullite composites was investigated by means of transmission electron microscopy after processing and heat treatment of the composites at 1000, 1200, and 1300 C for 6 h in air. The single-layer BN coatings were {approximately}0.7 {micro}m thick and consisted of turbostratic BN with (0001) basal planes lying parallel to the surfaces of the fibers plus nanosized areas that had no preferential orientation. This microstructure remained unchanged up to 1000 C; however, distinct coarsening of the randomly oriented BN crystallites occurred in the temperature range of 1000--1200 C. The single-layer BN coatings were stable against oxidation, up to 1200 C. At higher temperatures, degradation of the coatings via oxidation occurred. Double-layer BN/SiC coating systems consisted of BN that was 0.08 {micro}m thick and SiC layers that were 0.16 {micro}m thick and deposited onto the mullite fibers. The turbostratic BN was highly anisotropic and did not undergo any microstructural change, up to 1300 C. The outer SiC layer of the double-layer coating system improved the oxidation resistance of BN in the 1200--1300 C temperature range, despite a partial oxidation of SiC to SiO{sub 2}.

  15. Fabrication and optical properties of nanostructured plasmonic Al2O3/Au-Al2O3/Al2O3 metamaterials

    Science.gov (United States)

    Bakkali, H.; Blanco, E.; Domínguez, M.; Garitaonandia, J. S.

    2017-08-01

    Discontinuous multilayer (DML) thin films, which consist of nano-granular metals (NGMs) embedded in a dielectric matrix, have attracted significant interest as engineered plasmonic metamaterials. In this study, a systematic layer-by-layer deposition of three-dimensional sub-wavelength periodic plasmonic DML structures via the radio frequency sputtering of a composite target has been reported. The overall optical response of the DML films composed of Au-Al2O3 NGM homogenous layers, which are periodically sandwiched between two amorphous Al2O3 layers, are studied using reflection spectroscopic ellipsometry and transmission spectroscopy techniques. By applying the analytical optical approaches based on multiple Gaussian oscillators, ambient DML sub-wavelength structures have been successfully modeled. As a result, the effects of the size and shape of the Au nanoparticles as well as of the surrounding and interfacial media on their localized surface plasmon resonance (LSPR) are elucidated, and the related films thickness and effective optical constants are determined. Interestingly, during the examination of resonance frequencies and dielectric functions, the obtained DML structures exhibit unusual characteristics that are different from those of their NGM constituents due to the electromagnetic interactions of the NGM layers with the LSPR, which represent metamaterial features.

  16. Reaction dynamics in the combustion synthesis system of Al-CrO3-Al2O3-NaF-N2-O2

    Institute of Scientific and Technical Information of China (English)

    Dazheng Yang; Yue Zhang; Degang Li; Dianwei Qi; Wei Deng; Dayong Xun

    2007-01-01

    A new material with heat-resistant and adiabatic characteristics and high strength was prepared using the combustion synthesis method by mixed powders of CrO3, Al, Al2O3, and NaF in atmospheric gas. The reaction dynamic process of the Al-CrO3-NaF-Al2O3-N2-O2 new material system by the combustion synthesis method was discussed based on the observation results by SEM,EDS, and XRD in combination with the combustion front quenching method (CFQM) and the relation curves between reaction free enthalpies and the corresponding temperatures. The combustion synthesis mechanism and the formation reasons of the phase in the combustion product were analyzed.

  17. Microstructure and mechanical properties of ZrO2 (Y2O3)-Al2O3 nanocomposites prepared by spark plasma sintering

    Institute of Scientific and Technical Information of China (English)

    Shufeng Li; Hiroshi Izui; Michiharu Okano; Weihua Zhang; Taku Watanabe

    2012-01-01

    Zirconia (yttria)-alumina ceramic nanocomposites were fabricated from different powders by spark plasma sintering (SPS).One powder was a commercially available nanocomposite powder TZP-3Y2OA,consisting of 3 mol% yttria-stabilized zirconia (3-YSZ) reinforced with 20 wt% alumina,and the other,used as a comparison,was a conventional mechanically mixed powder 3YSZ-20A,a blend made of 3 mol% yttria-stabilized zirconia powder ZrO2 (3Y) and 20 wt% α-alumina powder.The effect of the sintering temperature on the densification,the sintering behavior,the mechanical properties and the microstructure of the composites was investigated.The results showed that the density increased with increasing sintering temperature,and thus,the mechanical properties were strengthened because of the increased densification.The nanocomposite powder TZP-3Y20A was easily sintered,and good mechanical properties were achieved as compared with the powder from the conventional mechanically mixed method,the maximum flexural strength and fracture toughness of which were 967 MPa and 5.27 MPa m1/2,respectively.

  18. Spectroscopic properties of Er3+-doped AlF3-La2O3-Al2O3-SiO2 glasses

    Institute of Scientific and Technical Information of China (English)

    Debao Zhang(张德宝); Baoyu Chen(陈宝玉); Zhuping Liu(柳祝平); Shunguang Li(李顺光); Lili Hu(胡丽丽)

    2004-01-01

    Er3+-doped fluoride lanthanum aluminosilicate glasses with compositions of (65- x/2)SiO2 · (25 -and their glass transition temperatures and spectroscopic properties were investigated. The Ω2, Ω4, and Ω6 intensity parameters of glasses were calculated by Judd-Ofelt theory from absorption curves. It was found that glasses transition temperature and melting temperature decreased with the increase of fluoride content in glass, Ω2 decreased gradually with the increase of AlF3 content, but both Ω4 and Ω6 did not increase until AlF3 content increased to 30 mol%. The quantum efficiency of 4I13/2 to 4I15/2 transition of Er3+ ions increases with the increase of AlF3 content in glass. Fluorescent lifetime is longer in glass containing more AlFa content.

  19. Study of hydration products in the system 4CaO.3Al2O3.SO2-CaSO4-CaO-H4O

    Directory of Open Access Journals (Sweden)

    Mihta, P. K.

    1974-06-01

    Full Text Available Not availableLos sistemas que implican la formación de sulfoaluminatos cálcicos hidratados pueden llegar a ser cada vez más importantes para la industria del cemento en virtud de su aplicación, mediante mezclas apropiadas, en los hormigones expansivos, los cuales están siendo investigados en el sentido de reducir el agrietamiento por retracción así como para la obtención de unidades estructurales químicamente pretensadas.

  20. Effect of cobalt and its adding sequence on the catalytic performance of MoO3/Al2O3 toward sulfur-resistant methanation

    Institute of Scientific and Technical Information of China (English)

    Baowei; Wang; Yuqin; Yao; Minhong; Jiang; Zhenhua; Li; Xinbin; Ma; Shaodong; Qin; Qi; Sun

    2014-01-01

    The effect of promoter cobalt and the sequences of adding cobalt and molybdenum precursors on the performance of sulfur-resistant methanation were investigated. All these samples were prepared by impregnation method and characterized by N2-adsorption, X-ray diffraction(XRD), temperature-programmed reduction(TPR) and laser Raman spectroscopy(LRS). The conversions of CO for Mo-Co/Al, Co-Mo/Al and CoMo/Al catalysts were 59.7%, 54.3% and 53.9%, respectively. Among these catalysts, the Mo-Co/Al catalyst prepared stepwisely by impregnating Mo precursor firstly showed the best catalytic performance. Meanwhile, the conversions of CO were 48.9% for Mo/Al catalyst and 10.5% for Co/Al catalyst. The addition of cobalt species could improve the catalytic activity of Mo/Al catalyst. The N2-adsorption results showed that Co-Mo/Al catalyst had the smallest specific surface area among these catalysts. CoMoO4species in CoMo/Al catalyst were detected with XRD, TPR and LRS. Moreover, crystal MoS2which was reported to be less active than amorphous MoS2was found in both Co-Mo/Al and CoMo/Al catalysts. Mo-Co/Al catalyst showed the best catalytic performance as it had an appropriate surface structure, i.e., no crystal MoS2and very little CoMoO4species.

  1. Interfacial band configuration and electrical properties of LaAlO3/Al2O3/hydrogenated-diamond metal-oxide-semiconductor field effect transistors

    Science.gov (United States)

    Liu, J. W.; Liao, M. Y.; Imura, M.; Oosato, H.; Watanabe, E.; Tanaka, A.; Iwai, H.; Koide, Y.

    2013-08-01

    In order to search a gate dielectric with high permittivity on hydrogenated-diamond (H-diamond), LaAlO3 films with thin Al2O3 buffer layers are fabricated on the H-diamond epilayers by sputtering-deposition (SD) and atomic layer deposition (ALD) techniques, respectively. Interfacial band configuration and electrical properties of the SD-LaAlO3/ALD-Al2O3/H-diamond metal-oxide-semiconductor field effect transistors (MOSFETs) with gate lengths of 10, 20, and 30 μm have been investigated. The valence and conduction band offsets of the SD-LaAlO3/ALD-Al2O3 structure are measured by X-ray photoelectron spectroscopy to be 1.1 ± 0.2 and 1.6 ± 0.2 eV, respectively. The valence band discontinuity between H-diamond and LaAlO3 is evaluated to be 4.0 ± 0.2 eV, showing that the MOS structure acts as the gate which controls a hole carrier density. The leakage current density of the SD-LaAlO3/ALD-Al2O3/H-diamond MOS diode is smaller than 10-8 A cm-2 at gate bias from -4 to 2 V. The capacitance-voltage curve in the depletion mode shows sharp dependence, small flat band voltage, and small hysteresis shift, which implies low positive and trapped charge densities. The MOSFETs show p-type channel and complete normally off characteristics with threshold voltages changing from -3.6 ± 0.1 to -5.0 ± 0.1 V dependent on the gate length. The drain current maximum and the extrinsic transconductance of the MOSFET with gate length of 10 μm are -7.5 mA mm-1 and 2.3 ± 0.1 mS mm-1, respectively. The enhancement mode SD-LaAlO3/ALD-Al2O3/H-diamond MOSFET is concluded to be suitable for the applications of high power and high frequency electrical devices.

  2. Al2O3/Al2O3 Joint Brazed with Al2O3-particulate-contained Composite Ag-Cu-Ti Filler Material

    Institute of Scientific and Technical Information of China (English)

    Jianguo YANG; Hongyuan FANG; Xin WAN

    2005-01-01

    Microstructure and interfacial reactions of Al2O3 joints brazed with Al2O3-particulate-contained composite Ag-Cu-Ti filler material were researched by scanning electron microscopy (SEM), electron probe microscopy analysis (EPMA),energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD). The interfacial reaction layer thickness of joints brazed with conventional active filler metal and active composite filler materials with different volume fraction of Al2O3 particulate was also studied. The experimental results indicated although there were Al2O3 particulates added into active filler metals, the time dependence of interfacial layer growth of joints brazed with active composite filler material is t1/2 as described by Fickian law as the joints brazed with conventional active filler metal.

  3. Novel Synthesis of Sol-gel Derived Nanosized Mullite Powder

    Institute of Scientific and Technical Information of China (English)

    LIANG Long; LI Jian-bao; LIN Hong; GUO Gang-feng; HE Ming-sheng

    2006-01-01

    Using hydrous aluminum chloride (AlCl3 6H2O) and silicon ethoxide (Si (OC2H5)4) as raw materials, a kind of nano-sized mullite powder was synthesized with the sol-gel process at the medium calcination temperature. The microstructures of the alumina-silica binary aerogel and calcined nano-sized materials were investigated by means of thermogravimetry-differential thermal analysis (TG-DTA), scanning electron microscopy (SEM) and X-ray diffractometer (XRD). The results show that the mullitization of Al2O3-SiO2 in gel starts from about 1 000 ℃ and its formation of mullite takes place in the range of 1 100 ℃-1 250 ℃. The size of the nano-sized mullite powder calcined at 1 250 ℃ is measured to be about 30 nm.

  4. Optimizing surface characteristics for cell adhesion and proliferation on titanium plasma spray coatings on polyetheretherketone.

    Science.gov (United States)

    Yoon, Byung Jo Victor; Xavier, Fred; Walker, Brendon R; Grinberg, Samuel; Cammisa, Frank P; Abjornson, Celeste

    2016-10-01

    Titanium plasma spray coating on polyetheretherketone (PEEK) is a recent innovation to interbody spacer technology. The inherent hydrophobic properties of standard, uncoated PEEK implants can hamper cell attachment and bone healing during fusion. The addition of titanium coating not only offers initial stability due to increased surface roughness but also long-term stability due to bony ongrowth created from osteoconductive microenvironment on the device surface. The previously established hydrophilic and osteophilic properties of commercially pure titanium (CPTi) can potentially provide an ideal environment promoting cell attachment and bony ongrowth when applied at the end plate level of the fusion site. Because the surface material composition and topography is what seems to directly affect cell adhesion, it is important to determine the ideal titanium coating for the highest effectiveness. The purpose of the study is to determine whether there is an optimal surface roughness for the titanium coatings and whether different polishing methods have a greater effect than roughness or topography in mediating cell adhesion to the surface. The study was divided into two phases. In Phase 1, the effects of varying surface roughnesses on identical polishing method were compared. In Phase 2, the effect of varying polishing methods was compared on identical surface roughnesses. Coating thickness, porosity, and surface roughness were characterized using an optical microscope as per ASTM F 1854 standards. For both phases, PEEK coupons with plasma-sprayed CPTi were used, and human mesenchymal stem cells (hMSCs) at an initial density of 25,000 cells/cm(2) were seeded and cultured for 24 hours before fixation in 10% formalin. The cultured hMSCs were visualized by 4',6-diamidino-2-phenylindole (DAPI) staining, a fluorescent stain that binds to the DNA of living cells. Samples were imaged using an environmental scanning electron microscope (eSEM) (Carl Zeiss Microscopy

  5. Surface characterization and cytotoxicity analysis of plasma sprayed coatings on titanium alloys

    Energy Technology Data Exchange (ETDEWEB)

    Rahman, Zia ur; Shabib, Ishraq [School of Engineering and Technology, Central Michigan University, Mount Pleasant, MI 48859 (United States); Science of Advanced Materials, Central Michigan University, Mount Pleasant, MI 48859 (United States); Haider, Waseem, E-mail: haide1w@cmich.edu [School of Engineering and Technology, Central Michigan University, Mount Pleasant, MI 48859 (United States); Science of Advanced Materials, Central Michigan University, Mount Pleasant, MI 48859 (United States)

    2016-10-01

    In the realm of biomaterials, metallic materials are widely used for load bearing joints due to their superior mechanical properties. Despite the necessity for long term metallic implants, there are limitations to their prolonged use. Naturally, oxides of titanium have low solubilities and form passive oxide film spontaneously. However, some inclusion and discontinuity spots in oxide film make implant to adopt the decisive nature. These defects heighten the dissolution of metal ions from the implant surface, which results in diminishing bio-integration of titanium implant. To increase the long-term metallic implant stability, surface modifications of titanium alloys are being carried out. In the present study, biomimetic coatings of plasma sprayed hydroxyapatite and titanium were applied to the surface of commercially pure titanium and Ti6Al4V. Surface morphology and surface chemistry were studied using scanning electron microscopy and X-ray photoelectron spectroscopy, respectively. Cyclic potentiodynamic polarization and electrochemical impedance spectroscopy were carried out in order to study their electrochemical behavior. Moreover, cytotoxicity analysis was conducted for osteoblast cells by performing MTS assay. It is concluded that both hydroxyapatite and titanium coatings enhance corrosion resistance and improve cytocompatibility. - Highlights: • Surface morphology and surface chemistry were studied using scanning electron microscopy and X-ray photoelectron spectroscopy. • The cyclic polarization tests revealed noticeable improvement towards the positive potentials for both Tip coatings. • CpTi-Hap and Ti6Al4V-Hap both demonstrate similar corrosion rate. • High cytotoxicity was observed for Mp when compared with Tip and Hap after 21 days of immersion. • Both Tip and Hap coatings promoted the osteoblast cell adhesion and exhibited stellar morphology.

  6. Method and Process Development of Advanced Atmospheric Plasma Spraying for Thermal Barrier Coatings

    Science.gov (United States)

    Mihm, Sebastian; Duda, Thomas; Gruner, Heiko; Thomas, Georg; Dzur, Birger

    2012-06-01

    Over the last few years, global economic growth has triggered a dramatic increase in the demand for resources, resulting in steady rise in prices for energy and raw materials. In the gas turbine manufacturing sector, process optimizations of cost-intensive production steps involve a heightened potential of savings and form the basis for securing future competitive advantages in the market. In this context, the atmospheric plasma spraying (APS) process for thermal barrier coatings (TBC) has been optimized. A constraint for the optimization of the APS coating process is the use of the existing coating equipment. Furthermore, the current coating quality and characteristics must not change so as to avoid new qualification and testing. Using experience in APS and empirically gained data, the process optimization plan included the variation of e.g. the plasma gas composition and flow-rate, the electrical power, the arrangement and angle of the powder injectors in relation to the plasma jet, the grain size distribution of the spray powder and the plasma torch movement procedures such as spray distance, offset and iteration. In particular, plasma properties (enthalpy, velocity and temperature), powder injection conditions (injection point, injection speed, grain size and distribution) and the coating lamination (coating pattern and spraying distance) are examined. The optimized process and resulting coating were compared to the current situation using several diagnostic methods. The improved process significantly reduces costs and achieves the requirement of comparable coating quality. Furthermore, a contribution was made towards better comprehension of the APS of ceramics and the definition of a better method for future process developments.

  7. Effects of Atomization Injection on Nanoparticle Processing in Suspension Plasma Spray

    Directory of Open Access Journals (Sweden)

    Hong-bing Xiong

    2016-05-01

    Full Text Available Liquid atomization is applied in nanostructure dense coating technology to inject suspended nano-size powder materials into a suspension plasma spray (SPS torch. This paper presents the effects of the atomization parameters on the nanoparticle processing. A numerical model was developed to simulate the dynamic behaviors of the suspension droplets, the solid nanoparticles or agglomerates, as well as the interactions between them and the plasma gas. The plasma gas was calculated as compressible, multi-component, turbulent jet flow in Eulerian scheme. The droplets and the solid particles were calculated as discrete Lagrangian entities, being tracked through the spray process. The motion and thermal histories of the particles were given in this paper and their release and melting status were observed. The key parameters of atomization, including droplet size, injection angle and velocity were also analyzed. The study revealed that the nanoparticle processing in SPS preferred small droplets with better atomization and less aggregation from suspension preparation. The injection angle and velocity influenced the nanoparticle release percentage. Small angle and low initial velocity might have more nanoparticles released. Besides, the melting percentage of nanoparticles and agglomerates were studied, and the critical droplet diameter to ensure solid melting was drawn. Results showed that most released nanoparticles were well melted, but the agglomerates might be totally melted, partially melted, or even not melted at all, mainly depending on the agglomerate size. For better coating quality, the suspension droplet size should be limited to a critical droplet diameter, which was inversely proportional to the cubic root of weight content, for given critical agglomerate diameter of being totally melted.

  8. Erosion Performance of Gadolinium Zirconate-Based Thermal Barrier Coatings Processed by Suspension Plasma Spray

    Science.gov (United States)

    Mahade, Satyapal; Curry, Nicholas; Björklund, Stefan; Markocsan, Nicolaie; Nylén, Per; Vaßen, Robert

    2017-01-01

    7-8 wt.% Yttria-stabilized zirconia (YSZ) is the standard thermal barrier coating (TBC) material used by the gas turbines industry due to its excellent thermal and thermo-mechanical properties up to 1200 °C. The need for improvement in gas turbine efficiency has led to an increase in the turbine inlet gas temperature. However, above 1200 °C, YSZ has issues such as poor sintering resistance, poor phase stability and susceptibility to calcium magnesium alumino silicates (CMAS) degradation. Gadolinium zirconate (GZ) is considered as one of the promising top coat candidates for TBC applications at high temperatures (>1200 °C) due to its low thermal conductivity, good sintering resistance and CMAS attack resistance. Single-layer 8YSZ, double-layer GZ/YSZ and triple-layer GZdense/GZ/YSZ TBCs were deposited by suspension plasma spray (SPS) process. Microstructural analysis was carried out by scanning electron microscopy (SEM). A columnar microstructure was observed in the single-, double- and triple-layer TBCs. Phase analysis of the as-sprayed TBCs was carried out using XRD (x-ray diffraction) where a tetragonal prime phase of zirconia in the single-layer YSZ TBC and a cubic defect fluorite phase of GZ in the double and triple-layer TBCs was observed. Porosity measurements of the as-sprayed TBCs were made by water intrusion method and image analysis method. The as-sprayed GZ-based multi-layered TBCs were subjected to erosion test at room temperature, and their erosion resistance was compared with single-layer 8YSZ. It was shown that the erosion resistance of 8YSZ single-layer TBC was higher than GZ-based multi-layered TBCs. Among the multi-layered TBCs, triple-layer TBC was slightly better than double layer in terms of erosion resistance. The eroded TBCs were cold-mounted and analyzed by SEM.

  9. Advanced Vacuum Plasma Spray (VPS) for a Robust, Longlife and Safe Space Shuttle Main Engine (SSME)

    Science.gov (United States)

    Holmes, Richard R.; Elam, Sandra K.; McKechnie, Timothy N.; Power, Christopher A.

    2010-01-01

    In 1984, the Vacuum Plasma Spray Lab was built at NASA/Marshall Space Flight Center for applying durable, protective coatings to turbine blades for the space shuttle main engine (SSME) high pressure fuel turbopump. Existing turbine blades were cracking and breaking off after five hot fire tests while VPS coated turbine blades showed no wear or cracking after 40 hot fire tests. Following that, a major manufacturing problem of copper coatings peeling off the SSME Titanium Main Fuel Valve Housing was corrected with a tenacious VPS copper coating. A patented VPS process utilizing Functional Gradient Material (FGM) application was developed to build ceramic lined metallic cartridges for space furnace experiments, safely containing gallium arsenide at 1260 degrees centigrade. The VPS/FGM process was then translated to build robust, long life, liquid rocket combustion chambers for the space shuttle main engine. A 5K (5,000 Lb. thrust) thruster with the VPS/FGM protective coating experienced 220 hot firing tests in pristine condition with no wear compared to the SSME which showed blanching (surface pulverization) and cooling channel cracks in less than 30 of the same hot firing tests. After 35 of the hot firing tests, the injector face plates disintegrated. The VPS/FGM process was then applied to spraying protective thermal barrier coatings on the face plates which showed 50% cooler operating temperature, with no wear after 50 hot fire tests. Cooling channels were closed out in two weeks, compared to one year for the SSME. Working up the TRL (Technology Readiness Level) to establish the VPS/FGM process as viable technology, a 40K thruster was built and is currently being tested. Proposed is to build a J-2X size liquid rocket engine as the final step in establishing the VPS/FGM process TRL for space flight.

  10. Effects of isothermal treatment on microstructure and scratch test behavior of plasma sprayed zirconia coatings

    Directory of Open Access Journals (Sweden)

    Veloso Guilherme

    2004-01-01

    Full Text Available The increase of the petroleum cost in the last decades revitalized the interest for lighter and more economic vehicles. Simultaneously, the demand for safe and unpolluted transports grows. The application of thermal barriers coatings (TBC on combustion chamber and on flat surface of pistons reduces the thermal losses of the engines, resulting in higher temperatures in the combustion chamber. This fact contributes to the improvement of the thermal efficiency (performance and for the reduction of incomplete combustion. Supported on these initial ideas, thermal barriers coatings constituted by CaO partially stabilized zirconia were produced and their microstructure examined. This coating still presents some drawbacks associated with thermal stresses and permeability to oxidizing gases, which will, eventually, lead to failure of the TBC by spallation. The failure may, in general, be associated to one of three factors: oxide growth at the ceramic-metal interface, formed during thermal cycling; stress build-up due to thermal cycling; and metal-oxide interface segregation, mainly of S. However, it is also relevant to understand the behavior of TBC's under isothermal oxidation. Therefore, this paper investigates the effect of oxidation on the adherence of thermal sprayed coatings. The adherence was measured by linear scratching tests, widely used for thin coatings. Plasma sprayed calcia partially stabilized zirconia was used as TBC and Ni-5%Al as bond coat, with Al substrates. Coated samples were submitted to heat treatments at 500 °C, for 50 h. The microstructures were examined by optical light microscopy, X-ray diffraction, profilometry and SEM.

  11. Microstructural evolution and growth kinetics of thermally grown oxides in plasma sprayed thermal barrier coatings

    Directory of Open Access Journals (Sweden)

    Xiaoju Liu

    2016-02-01

    Full Text Available The formation of thermally grown oxide (TGO during high temperature is a key factor to the degradation of thermal barrier coatings (TBCs applied on hot section components. In the present study both the CoNiCrAlY bond coat and ZrO2-8 wt.% Y2O3 (8YSZ ceramic coat of TBCs were prepared by air plasma spraying (APS. The composition and microstructure of TGO in TBCs were investigated using scanning electron microscopy (SEM, energy dispersive spectroscopy (EDS and X-ray diffraction (XRD analysis. The growth rate of TGO for TBC and pure BC were gained after isothermal oxidation at 1100 °C for various times. The results showed that as-sprayed bond coat consisted of β and γ/γ′phases, β phase reducesd as the oxidation time increased. The TGO comprised α-Al2O3 formed in the first 2 h. CoO, NiO, Cr2O3 and spinel oxides appeared after 20 h of oxidation. Contents of CoO and NiO reduced while that of Cr2O3 and spinel oxides increased in the later oxidation stage. The TGO eventually consisted of a sub-Al2O3 layer with columnar microstructure and the upper porous CS clusters. The TGO growth kinetics for two kinds of samples followed parabolic laws, with oxidation rate constant of 0.344 μm/h0.5 for TBCs and 0.354 μm/h0.5 for pure BCs.

  12. Microstructural evolution and growth kinetics of thermally grown oxides in plasma sprayed thermal barrier coatings

    Institute of Scientific and Technical Information of China (English)

    Xiaoju Liu; Teng Wang; Caicai Li; Zhenhuan Zheng; Qiang Li

    2016-01-01

    The formation of thermally grown oxide (TGO) during high temperature is a key factor to the degradation of thermal barrier coatings (TBCs) applied on hot section components. In the present study both the CoNiCrAlY bond coat and ZrO2-8 wt.% Y2O3 (8YSZ) ceramic coat of TBCs were prepared by air plasma spraying (APS). The composition and microstructure of TGO in TBCs were investigated using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD) analysis. The growth rate of TGO for TBC and pure BC were gained after isothermal oxidation at 1100 °C for various times. The results showed that as-sprayed bond coat consisted of β and γ/γ'phases,β phase reducesd as the oxidation time increased. The TGO comprised α-Al2O3 formed in the first 2 h. CoO, NiO, Cr2O3 and spinel oxides appeared after 20 h of oxidation. Contents of CoO and NiO reduced while that of Cr2O3 and spinel oxides increased in the later oxidation stage. The TGO eventually consisted of a sub-Al2O3 layer with columnar microstructure and the upper porous CS clusters. The TGO growth kinetics for two kinds of samples followed parabolic laws, with oxidation rate constant of 0.344 μm/h0.5 for TBCs and 0.354 μm/h0.5 for pure BCs.

  13. Influence of a powder feed rate on the properties of the plasma sprayed chromium carbide- 25% nickel chromium coating

    Directory of Open Access Journals (Sweden)

    Mihailo R. Mrdak

    2014-04-01

    Full Text Available Normal 0 false false false MicrosoftInternetExplorer4 The plasma spray process is a leading technology of powder depositing in the production of coatings widely used in the aerospace industry for the protection of new parts and for the repair of worn ones. Cermet 75Cr3C2 - 25Ni(Cr coatings based on Cr3C2 carbides are widely used to protect parts as they retain high values of hardness, strength and resistance to wear up to a temperature of 850°C. This paper discusses the influence of the parameters of the plasma spray deposition of 75Cr3C2 - 25Ni(Cr powder on the structure and mechanical properties of the coating. The powder is deposited using plasma spraying at atmospheric pressure (APS. The plasma gas is He, which is an inert gas and does not react with the powder; it produces dense plasma with lower heat content and less incorporated ambient air in the plasma jet thus reducing temperature decomposition and decarburization of Cr3C2 carbide.. In this study, three groups of coatings were deposited with three different powder feed rates of: 30, 45 and 60 g/min. The  coating with the best properties was deposited on the inlet flange parts of the turbo - jet engine TV2-117A to reduce the influence of vibrations and wear. The structures and the mechanical properties of 75Cr3C2 - 25Ni(Cr coatings are analyzed in accordance with the Pratt & Whitney standard. Studies have shown that powder feed rates have an important influence on the mechanical properties and structures of 75Cr3C2 - 25Ni(Cr coatings. 

  14. Study of the Porosity in Plasma-Sprayed Alumina through an Innovative Three-Dimensional Simulation of the Coating Buildup

    Science.gov (United States)

    Beauvais, S.; Guipont, V.; Jeandin, M.; Jeulin, D.; Robisson, A.; Saenger, R.

    2008-11-01

    Porosity is a key feature of a thermally sprayed coating microstructure. Within ceramic coatings, porosity is made of pores and cracks of various shapes, dimensions, and orientations. Cracks can be intralamellar or interlamellar due to the buildup of the coating, which leads to piled-up lamellae from impinging and the additional rapid solidification of liquid droplets. Pores are interconnected with cracks, which results in a three-dimensional (3-D) porosity network. Direct observation of this network is an intricate task and current attempts remain somewhat limited. A 3-D simulation of this network was, therefore, developed in this work, based on a stochastic approach to the building up of simulated lamellae in the sprayed microstructure. A library of mathematical objects was achieved from morphological measurements, using confocal microscopy of actual isolated flattened lamellae, i.e., “splats” and scanning electron microscopy (SEM). This stochastic approach to the simulation of hundreds of lamellae also involves the random distribution of cracks and pores. Simulation fit parameters were selected according to the overall characteristics of porosity ( i.e., content, orientation, size, etc.) that were determined from the thorough quantitative image analysis (QIA) of cross-sectioned plasma-sprayed alumina coatings. Two plasma modes that varied the atmosphere in a controlled-atmosphere plasma spraying (CAPS) chamber were applied, to produce the microstructures of two different alumina coatings. The 3-D random modeling tool allowed the processing of a volume of digital material through a 3-D simulated binary image of a two-phased composite material. Using one 3-D image result of the simulation, finite element (FE) calculations were performed, in order to study the overall dielectric properties of a plasma-sprayed alumina as a function of porosity. The influence of anisotropy is discussed, in particular, and both analytical and numerical predicted values were

  15. A systematic review on the long-term success of calcium phosphate plasma-spray-coated dental implants.

    Science.gov (United States)

    van Oirschot, B A J A; Bronkhorst, E M; van den Beucken, J J J P; Meijer, G J; Jansen, J A; Junker, R

    2016-09-01

    The objectives of the current review were (1) to systematically appraise, and (2) to evaluate long-term success data of calcium phosphate (CaP) plasma-spray-coated dental implants in clinical trials with at least 5 years of follow-up. To describe the long-term efficacy of functional implants, the outcome variables were (a) percentage annual complication rate (ACR) and (b) cumulative success rate (CSR), as presented in the selected articles. The electronic search yielded 645 titles. On the basis of the inclusion criteria, 8 studies were finally included. The percentage of implants in function after the first year was estimated to be 98.4 % in the maxilla and 99.2 % in the mandible. The estimates of the weighted mean ACR-percentage increased over the years up to 2.6 (SE 0.7) during the fifth year of function for the maxilla and to 9.4 (SE 8.4) for the mandible in the tenth year of function. After 10 years, the mean percentage of successful implants was estimated to be 71.1 % in the maxilla and 72.2 % in the mandible. The estimates seem to confirm the proposed, long-term progressive bone loss pattern of CaP-ceramic-coated dental implants. Within the limits of this meta-analytic approach to the literature, we conclude that: (1) published long-term success data for calcium phosphate plasma-spray-coated dental implants are limited, (2) comparison of the data is difficult due to differences in success criteria among the studies, and (3) long-term CSRs demonstrate very weak evidence for progressive complications around calcium phosphate plasma-spray-coated dental implants.

  16. Fireside Corrosion Behavior of HVOF and Plasma-Sprayed Coatings in Advanced Coal/Biomass Co-Fired Power Plants

    Science.gov (United States)

    Hussain, T.; Dudziak, T.; Simms, N. J.; Nicholls, J. R.

    2013-06-01

    This article presents a systematic evaluation of coatings for advanced fossil fuel plants and addresses fireside corrosion in coal/biomass-derived flue gases. A selection of four candidate coatings: alloy 625, NiCr, FeCrAl and NiCrAlY were deposited onto superheaters/reheaters alloy (T91) using high-velocity oxy-fuel (HVOF) and plasma spraying. A series of laboratory-based fireside corrosion exposures were carried out on these coated samples in furnaces under controlled atmosphere for 1000 h at 650 °C. The tests were carried out using the "deposit-recoat" test method to simulate the environment that was anticipated from air-firing 20 wt.% cereal co-product mixed with a UK coal. The exposures were carried out using a deposit containing Na2SO4, K2SO4, and Fe2O3 to produce alkali-iron tri-sulfates, which had been identified as the principal cause of fireside corrosion on superheaters/reheaters in pulverized coal-fired power plants. The exposed samples were examined in an ESEM with EDX analysis to characterize the damage. Pre- and post-exposure dimensional metrologies were used to quantify the metal damage in terms of metal loss distributions. The thermally sprayed coatings suffered significant corrosion attack from a combination of aggressive combustion gases and deposit mixtures. In this study, all the four plasma-sprayed coatings studied performed better than the HVOF-sprayed coatings because of a lower level of porosity. NiCr was found to be the best performing coating material with a median metal loss of ~87 μm (HVOF sprayed) and ~13 μm (plasma sprayed). In general, the median metal damage for coatings had the following ranking (in the descending order: most to the least damage): NiCrAlY > alloy 625 > FeCrAl > NiCr.

  17. The Effect of Plasma Spraying on the Microstructure and Aging Kinetics of the Al-Si Matrix Alloy and Al-Si/SiC Composites

    Science.gov (United States)

    Altunpak, Yahya; Akbulut, Hatem; Üstel, Fatih

    2010-02-01

    The Al-Si (LM 13)-based matrix alloy reinforced with SiC particles containing 10, 20, and 30 vol.% SiC particles were spray-formed onto Al-Si substrates. The sprayed samples were directly subjected to a standard aging treatment (T551). From the experiments, it was observed that the high rate of solidification resulted in very fine silicon particles which were observed as continuous islands in the matrix and each island exhibited several very fine silicon crystals. Analysis showed that plasma-spraying caused an increased solid solubility of the silicon in the aluminum matrix. DSC measurements in the permanent mold-cast Al-Si matrix alloy and plasma-sprayed Al-Si matrix alloy showed that plasma-spraying causes an increase in the amount of GP-zone formation owing to the very high rate solidification after plasma-spraying. In the plasma-sprayed Al-Si/SiC composites GP zones were suppressed, since particle-matrix interfaces act as a sink for vacancies during quenching from high plasma process temperature. Introduction of SiC particles to the Al-Si age-hardenable alloy resulted in a decrease in the time required to reach plateau matrix hardness owing to acceleration of aging kinetics by ceramic SiC particles.

  18. Prediction and optimization of process variables to maximize the Young's modulus of plasma sprayed alumina coatings on AZ31B magnesium alloy

    Directory of Open Access Journals (Sweden)

    D. Thirumalaikumarasamy

    2017-03-01

    Full Text Available Like other manufacturing techniques, plasma spraying has also a non-linear behavior because of the contribution of many coating variables. This characteristic results in finding optimal factor combination difficult. Subsequently, the issue can be solved through effective and strategic statistical procedures integrated with systematic experimental data. Plasma spray parameters such as power, stand-off distance and powder feed rate have significant influence on coating characteristics like Young's modulus. This paper presents the use of statistical techniques in specifically response surface methodology (RSM, analysis of variance, and regression analysis to develop empirical relationship to predict Young's modulus of plasma-sprayed alumina coatings. The developed empirical relationships can be effectively used to predict Young's modulus of plasma-sprayed alumina coatings at 95% confidence level. Response graphs and contour plots were constructed to identify the optimum plasma spray parameters to attain maximum Young's modulus in alumina coatings. A linear regression relationship was established between porosity and Young's modulus of the alumina coatings.

  19. Mechanical properties and microstructure of vaccum plasma sprayed Cr3C2 - 25(Ni20Cr) coatings

    OpenAIRE

    MRDAK MIHAILO R.

    2015-01-01

    This paper analyzes vacuum plasma spray VPS - Cr3C2 - 25(Ni20Cr) coatings. Commercial powder marked Sulzer Metco Woka 7205 is used. The powder is deposited with a plasma gun F4 at a distance of 340 mm from the substrate. The main objective of the study was to eliminate, at the reduced pressure of inert gas Ar, the degradation of primary Cr3C2 carbide into Cr23C6 carbide which significantly reduces the microhardness and mechanical properties of the coating. The coating is deposited with a thic...

  20. Some adhesion/cohesion characteristics of plasma-sprayed ZrO2-Y2O3 under tensile loading

    Science.gov (United States)

    Mullen, Robert L.; Vlcek, Brian L.; Hendricks, Robert C.; Mcdonald, Glen

    1987-01-01

    A set of 12.7 mm diameter stainless steel tubes were coated with ceramic and expanded. The bond cast was 0.08 to 0.13 mm NiCrAlY with 0.38 mm of ZrO2-8Y2O3 ceramic. Upon pressurization, the tube substrate yielded and overstressed the coatings in tension. The coatings cracked (i.e., they failed) but did not come off the tube. These results demonstrate that tensile failure of plasma-sprayed coatings is not catastrophic as is compressive failure, which leads to spallation.

  1. Growth of textured mullite fibers using polycrystalline precursors

    Science.gov (United States)

    Yoon, Wonki

    Fine ceramic oxide fibers are widely used as reinforcements in composites for high temperature applications. The primary goal of this research was to investigate the growth of textured or single crystal oxide fibers by heat treatment of polycrystalline or amorphous, extruded precursor fibers. Mullite was selected for this study due to its excellent chemical stability, creep resistance and strength at high temperatures. Micrographic analysis and in-situ synchrotron X-ray diffraction analysis have been performed on mullite systems in order to study the anisotropic grain growth and the effect of titania additions in mullite. The estimated activation energies from the SEM micrographic particle size analysis were 644.3 kJ/mol and 773.7 kJ/mol for the length and thickness, respectively. An in-situ synchrotron X-ray diffraction microstructure analysis was done with a Curved Image Plate (CIP) detector and the fiber was heat treated in a QLF. The apparent crystallite size showed anisotropy in crystallite growth. Furthermore, a higher growth rate along the [001] direction than the [110] direction was observed. Mullite whiskers were prepared by HF leaching and templated into polycrystalline mullite fibers by extrusion. Textured growth of mullite fibers with elongated grains, aligned along the long-axis of the fibers, was achieved by heat treatment. Repeated heat treatment cycles of a whisker-templated fiber showed a bamboo-like microstructure. It was confirmed by SEM, TEM and optical microscopy (OM) that the growth direction along the fiber length was the [001] direction of orthorhombic mullite.

  2. Effect of Samarium Oxide on the Electrical Conductivity of Plasma-Sprayed SOFC Anodes

    Science.gov (United States)

    Panahi, S. N.; Samadi, H.; Nemati, A.

    2016-10-01

    Solid oxide fuel cells (SOFCs) are rapidly becoming recognized as a new alternative to traditional energy conversion systems because of their high energy efficiency. From an ecological perspective, this environmentally friendly technology, which produces clean energy, is likely to be implemented more frequently in the future. However, the current SOFC technology still cannot meet the demands of commercial applications due to temperature constraints and high cost. To develop a marketable SOFC, suppliers have tended to reduce the operating temperatures by a few hundred degrees. The overall trend for SOFC materials is to reduce their service temperature of electrolyte. Meanwhile, it is important that the other components perform at the same temperature. Currently, the anodes of SOFCs are being studied in depth. Research has indicated that anodes based on a perovskite structure are a more promising candidate in SOFCs than the traditional system because they possess more favorable electrical properties. Among the perovskite-type oxides, SrTiO3 is one of the most promising compositions, with studies demonstrating that SrTiO3 exhibits particularly favorable electrical properties in contrast with other perovskite-type oxides. The main purpose of this article is to describe our study of the effect of rare-earth dopants with a perovskite structure on the electrical behavior of anodes in SOFCs. Sm2O3-doped SrTiO3 synthesized by a solid-state reaction was coated on substrate by atmospheric plasma spray. To compare the effect of the dopant on the electrical conductivity of strontium titanate, different concentrations of Sm2O3 were used. The samples were then investigated by x-ray diffraction, four-point probe at various temperatures (to determine the electrical conductivity), and a scanning electron microscope. The study showed that at room temperature, nondoped samples have a higher electrical resistance than doped samples. As the temperature was increased, the electrical

  3. Effect of Dry-Ice Blasting on Structure and Magnetic Properties of Plasma-Sprayed Fe-40Al Coating from Nanostructured Powders

    Science.gov (United States)

    Song, Bo; Dong, Shujuan; Hansz, Bernard; Liao, Hanlin; Coddet, Christian

    2014-01-01

    Amorphous and nanocrystalline materials have attracted much interest in the field of new materials design because of their excellent mechanical and physical properties as well as their magnetic properties. In this work, Fe-40Al coatings were prepared from a nanostructured feedstock by atmospheric plasma spray combined with dry-ice blasting. The scanning electron microscopy, x-ray diffraction, tensile test, and magnetic measurements were used to investigate microstructure, phase structure, adhesion, and magnetic properties of the deposited coatings. The results showed that after using dry-ice blasting, the oxidation and porosity decreased and the atmospheric plasma-sprayed Fe-40Al coatings exhibited a soft ferromagnetic character with lower coercivity and higher saturation magnetization due to their lower degree of order. The plasma-sprayed Fe-40Al coating from the nanostructured feedstock has a very high adhesive strength.

  4. Molten salt synthesis of mullite nanowhiskers using different silica sources

    Institute of Scientific and Technical Information of China (English)

    Tao Yang; Peng-long Qiu; Mei Zhang; Kuo-Chih Chou; Xin-mei Hou; Bai-jun Yan

    2015-01-01

    Mullite nanowhiskers with Al-rich structure were prepared by molten salt synthesis at 1000°C for 3 h in air using silica, amor-phous silica, and ultrafine silica as the silica sources. The phase and morphology of the synthesized products were investigated by X-ray dif-fraction, scanning electron microscopy, energy dispersive spectroscopy, and transmission electron microscopy. A thermogravimetric and differential thermal analysis was carried out to determine the reaction mechanism. The results reveal that the silica sources play an important role in determining the morphology of the obtained mullite nanowhiskers. Clusters and disordered arrangements are obtained using common silica and amorphous silica, respectively, whereas the use of ultrafine silica leads to highly ordered mullite nanowhiskers that are 80−120 nm in diameter and 20−30μm in length. Considering the growth mechanisms, mullite nanowhiskers in the forms of clusters and highly ordered arrangements can be attributed to heterogeneous nucleation, whereas disordered mullite nanowhiskers are obtained by homogenous nuclea-tion.

  5. Mechanical behavior of mullite-zirconia composites

    Science.gov (United States)

    Sahnoune, F.; Saheb, N.

    2010-06-01

    In this work, mechanical properties of mullite-zirconia composites synthesised through reaction sintering of Algerian kaolin, α-Al2O3, and ZrO2 were characterized. Phases present and their transformations were characterized using x-ray diffraction. Hardness H and fracture toughness KIC were measured by Vickers indentation using a Zwick microhardness tester. The flexural strength was measured through three point bending test using an Instron Universal Testing Machine. It was found that the increase of ZrO2 content (from 0 to 32wt.%) decreased the microhardness of the composites from 14 to 10.8 GPa. However, the increase of ZrO2 content (from 0 to 24wt.%) increased the flexural strength of the composites from 142 to 390 MPa then decreased it with further increase of ZrO2 content. Also, the fracture toughness increased from 1.8 to 2.9 MPa.m1/2 with the increase of ZrO2 content from 0 to 32 wt.%; and the rate of the increase decreased at higher fractions of ZrO2 content. The average linear coefficient of thermal expansion (within the range 50 to 1450°C) for samples containing 0 and 16 wt.% ZrO2 sintered at 1600°C for 2 hours was 4.7 x10-6 K-1 and 5.2 x 10-6 K-1 respectively.

  6. Fiber-coatings for fiber-reinforced mullite/mullite composites

    Energy Technology Data Exchange (ETDEWEB)

    Nubian, K.; Wahl, G. [Technische Univ. Braunschweig (Germany). Inst. fuer Oberflaechentechnik und Plasmatechnische Werkstoffentwicklung; Saruhan, B.; Schneider, H. [Technische Univ. Braunschweig (Germany). Inst. fuer Oberflaechentechnik und Plasmatechnische Werkstoffentwicklung; DLR, Deutsches Zentrum fuer Luft- und Raumfahrt e.v., Koeln (Germany)

    2001-08-01

    Mullite-based fiber-reinforced composites are favorite candidates for the application in combustion chambers of gas turbines. The application requires damage tolerance, temperature and oxidation-resistance at high temperatures (> 1200 C) over long terms. In order to realize crack deflection and fiber pull-out, an interphase coating of the mullite fibers (Nextel{sup TM} 720) is necessary to obtain a weak bonding between fibers and matrix. Two systems of interphases produced by CVD were described. The first system is a carbon/metal-oxide double layer (C/ZrO{sub 2}, C/Al{sub 2}O{sub 3}). Properties of the resulting composites after heat-treatment (1300 C, 1000 h) under cyclic and continuous heating conditions were described. The second system is the codeposition of La{sub 2}O{sub 3} and Al{sub 2}O{sub 3} on the fibers. After heat-treatment at 1300 C lanthanum hexaluminate (LaAl{sub 11}O{sub 18}) with a magneto plumbite structure containing sliding planes should be formed. (orig.)

  7. One-Step Synthesis of Pt/Graphene Composites from Pt Acid Dissolved Ethanol via Microwave Plasma Spray Pyrolysis

    Science.gov (United States)

    Jo, Eun Hee; Chang, Hankwon; Kim, Sun Kyung; Choi, Ji-Hyuk; Park, Su-Ryeon; Lee, Chong Min; Jang, Hee Dong

    2016-09-01

    Pt nanoparticles-laden graphene (Pt/GR) composites were synthesized in the gas phase from a mixture of ethanol and Pt precursor by microwave plasma spray pyrolysis. The morphology of Pt/GR composites has the shape of wrinkled sheets of paper, while Pt nanoparticles (Pt NPs) that are less than 2.6 nm in the mean diameter are uniformly well deposited on the surface of GR sheets stacked in only three layers. The Pt/GR composite prepared with 20 wt% of Pt had the highest specific surface area and electrochemical surface area of up to 402 m2 g-1 and 77 m2 g-1 (Pt), respectively. In addition, the composite showed superior electrocatalytic activity compared with commercial Pt-carbon black. The excellent electrocatalytic activity was attributed to the high specific surface area and electrochemical surface area of the Pt/GR composite directly produced by microwave plasma spray pyrolysis. Thus, it is clearly expected that the Pt/GR composite is a promising material for DMFC catalysts.

  8. In vitro corrosion investigations of plasma-sprayed hydroxyapatite and hydroxyapatite–calcium phosphate coatings on 316L SS

    Indian Academy of Sciences (India)

    Gurpreet Singh; Hazoor Singh; Buta Singh Sidhu

    2014-10-01

    The present paper discusses various issues associated with biological corrosion of uncoated and plasma-sprayed hydroxyapatite (HA)-coated 316L SS and studies the effect of contents of calcium phosphate (CaP) on corrosion behaviour of hydroxyapatite (HA) coatings in simulated body fluid (Ringer’s solution). Three types of coatings, i.e. HA + 20 wt% CaP (type 1), HA + 10 wt% CaP (type 2), HA (type 3), were laid on 316L SS using plasma-spraying technique. Structural characterization techniques including X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX) were used to investigate the crystallinity, microstructure and morphology of the coatings. Electrochemical potentiodynamic tests were performed to determine the corrosion resistance of uncoated and all the three coatings. After the electrochemical corrosion testing, the samples were examined by XRD, SEM and EDX. The electrochemical study showed a significant improvement in the corrosion resistance after HA coating and corrosion resistance of type 3 coating was found maximum.

  9. Modeling the impact, flattening and solidification of a molten droplet on a solid substrate during plasma spraying

    Science.gov (United States)

    Zheng, Y. Z.; Li, Q.; Zheng, Z. H.; Zhu, J. F.; Cao, P. L.

    2014-10-01

    It is quite important to clearly understand the dynamic process of single splat formation for optimizing the plasma spraying process. In present study, a three-dimensional model including heat transfer and phase change was developed on Ansys Fluent 14 platform to simulate the impact, flattening and solidification of a molten droplet on a solid substrate during plasma spraying. The phase, contact pressure, temperature and velocity fields at different spreading times were presented to gain an insight into splat formation mechanism. The predicted splat morphology was in good agreement with the experimental photos. The effect of mushy zone constant, a parameter dominating the solidification behavior of fluid in Fluent, on the flattening of droplet was further investigated. Through comparing the calculated spread factor from present model with the experimental value, a mushy zone constant of 108 or 109 was found to be more appropriate for simulation on the solidification problem occurring in high-speed impact and flattening process, instead of the range of 104-107 recommended in Fluent.

  10. Atmospheric plasma sprayed (APS) coatings of Al2O3-TiO2 system for photocatalytic application.

    Science.gov (United States)

    Stengl, V; Ageorges, H; Ctibor, P; Murafa, N

    2009-05-01

    The goal of this study is to examine the photocatalytic ability of coatings produced by atmospheric plasma spraying (APS). The plasma gun used is a common gas-stabilized plasma gun (GSP) working with a d.c. current and a mixture of argon and hydrogen as plasma-forming gas. The TiO(2) powders are particles of about 100 nm which were agglomerated to a mean size of about 55 mum, suitable for spraying. Composition of the commercial powder is 13 wt% of TiO(2) in Al(2)O(3), whereas also in-house prepared powder with the same nominal composition but with agglomerated TiO(2) and conventional fused and crushed Al(2)O(3) was sprayed. The feedstock materials used for this purpose are alpha-alumina and anatase titanium dioxide. The coatings are analyzed by scanning electron microscopy (SEM), energy dispersion probe (EDS) and X-ray diffraction. Photocatalytic degradation of acetone is quantified for various coatings. All plasma sprayed coatings show a lamellar structure on cross section, as typical for this process. Anatase titania from feedstock powder is converted into rutile titania and alpha-alumina partly to gamma-alumina. Coatings are proven to catalyse the acetone decomposition when irradiated by UV rays.

  11. Comparison of ZrB2-MoSi2 Composite Coatings Fabricated by Atmospheric and Vacuum Plasma Spray Processes

    Science.gov (United States)

    Niu, Yaran; Wang, Zhong; Zhao, Jun; Zheng, Xuebin; Zeng, Yi; Ding, Chuanxian

    2016-12-01

    In this work, ZrB2-20 vol.% MoSi2 (denoted as ZM) composite coatings were fabricated by atmospheric plasma spray (APS) and vacuum plasma spray (VPS) techniques, respectively. Phase composition and microstructure of the composite coatings were characterized. Their oxidation behaviors and microstructure changes at 1500 °C were comparatively investigated. The results showed that VPS-ZM coating was composed of hexagonal ZrB2, tetragonal and hexagonal MoSi2, while certain amount of ZrO2 existed in APS-ZM coating. The oxide content, surface roughness and porosity of VPS-ZM coating were apparently lower than those of APS-ZM coating. The mass gain of APS-ZM coating was maximum at the beginning (1500 °C, 0 h) and then decreased with the oxidation time extending, while the mass of VPS-ZM coating gradually increased with increasing the oxidation time. The possible reasons for the different oxidation behaviors of the two kinds of coatings were analyzed.

  12. La2NiO4+δ Infiltration of Plasma-Sprayed LSCF Coating for Cathode Performance Improvement

    Science.gov (United States)

    Li, Ying; Zhang, Shan-Lin; Li, Cheng-Xin; Wei, Tao; Yang, Guan-Jun; Li, Chang-Jiu; Liu, Meilin

    2016-01-01

    Perovskite-structured (La0.6Sr0.4Co0.2Fe0.8O3) LSCF has been widely studied as a cathode material for intermediate-temperature solid oxide fuel cells. However, the application of LSCF cathode is likely to be limited by its sluggish surface catalytic properties and long-term stability issues. Oxygen hyper-stoichiometric La2NiO4+δ with K2NiF4 structure exhibits higher catalytic properties, ionic conductivity, and stability in comparison with LSCF cathode. Due to the good chemical compatibility of these two cathode materials, it is possible to prepare a composite cathode by the infiltration of La2NiO4+δ in the porous LSCF. This composite structure fully utilizes the advantages of the two cathodes and enhances the LSCF cathode performance. In this study, the LSCF cathode was deposited by using an atmospheric plasma spray technique, and the porous LSCF cathode was then infiltrated by La2NiO4+δ. The atmospheric plasma spray technique was used to reduce the SOFC manufacturing cost. The microstructure of coatings was characterized by SEM and EDS. The cathode polarization resistance was found to decrease by ~40% after the La2NiO4+δ infiltration. Also, the activation energy decreased from 1.53 to 1.40 eV.

  13. Modification of vacuum plasma sprayed tungsten coating on reduced activation ferritic/martensitic steels by friction stir processing

    Energy Technology Data Exchange (ETDEWEB)

    Tanigawa, Hiroyasu, E-mail: tanigawa.hiroyasu@jaea.go.jp [Fusion Research and Development Directorate, Japan Atomic Energy Agency, Rokkasho, Aomori (Japan); Ozawa, Kazumi [Fusion Research and Development Directorate, Japan Atomic Energy Agency, Rokkasho, Aomori (Japan); Morisada, Yoshiaki [Joining and Welding Research Institute, Osaka University, Ibaraki, Osaka (Japan); Noh, Sanghoon [Fusion Research and Development Directorate, Japan Atomic Energy Agency, Rokkasho, Aomori (Japan); Nuclear Material Development Division, Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Fujii, Hidetoshi [Joining and Welding Research Institute, Osaka University, Ibaraki, Osaka (Japan)

    2015-10-15

    Highlights: • Friction stir processing (FSP) was applied on vacuum plasma spray (VPS) W to improve its low thermal conductivity and weakness due to high porosity. • FSP can achieve significant improvement both in mechanical and thermal properties of VPS-W coating. • It was indicated that the double pass FSP at 600 rpm/50 mm/min/2 ton on VPS-W show the most dense microstructure and hardest mechanical property. • Hardness test over FSPed VPS-W layer revealed that the hardness of W becomes higher than that of bulk W. • The thermal conductivity of double pass FSPed VPS-W was about 80% of bulk W at 200 °C, and it becomes equivalent to that of bulk W over 800 °C. - Abstract: Tungsten (W) is the primary candidate material as a plasma facing material in fusion devices, as for its high melting temperature, good thermal conductivity and low sputtering rate, and vacuum plasma spray (VPS) technique is preferred as it is applicable for large area without brittle interlayer, but the thermal conductivity of W layer is very poor, and easy to detach, mainly caused by its porous structure. W Friction stir processing (FSP) was applied on VPS-W to improve these poor properties, and it was suggested that FSP can contribute to significant improvement in both mechanical and thermal properties of the VPS-W coating.

  14. Effect of Sulfur Acid Corrosion on the Luminescent Intensity of Plasma-Sprayed YAG:Ce Coatings

    Science.gov (United States)

    Wang, Weize; Zeng, Peng; Wang, Hehui; Yu, Jingye; Wu, Liangmin

    2016-12-01

    In order to monitor the corrosion condition of components, plasma-sprayed YAG:Ce coating was prepared for the detection, which could develop the application of plasma spraying. The effect of sulfuric acid corrosion on the microstructure, phase composition and luminescence intensity of coatings was studied. The powder was synthesized by the high-temperature solid-state method. Microstructure and phases were characterized through using SEM and XRD, respectively. Effect of immersion time in the acid was studied on the luminescence intensity. It was found that the phase composition of the powder was dominated by YAG (Y3Al5O12). More pores could be observed in coatings with the increase in immersion time. Sprayed coatings mainly included phases of YAG and YAP (YAlO3). The position of the XRD peaks of coatings was changing during the immersion. The luminescence intensity showed the fluctuation tendency with the immersion time, which related to the coating porosity, phase composition and the migration of the diffract peak.

  15. Thermal Fatigue Behavior of Air-Plasma Sprayed Thermal Barrier Coating with Bond Coat Species in Cyclic Thermal Exposure

    Directory of Open Access Journals (Sweden)

    Ungyu Paik

    2013-08-01

    Full Text Available The effects of the bond coat species on the delamination or fracture behavior in thermal barrier coatings (TBCs was investigated using the yclic thermal fatigue and thermal-shock tests. The interface microstructures of each TBC showed a good condition without cracking or delamination after flame thermal fatigue (FTF for 1429 cycles. The TBC with the bond coat prepared by the air-plasma spray (APS method showed a good condition at the interface between the top and bond coats after cyclic furnace thermal fatigue (CFTF for 1429 cycles, whereas the TBCs with the bond coats prepared by the high-velocity oxygen fuel (HVOF and low-pressure plasma spray (LPPS methods showed a partial cracking (and/or delamination and a delamination after 780 cycles, respectively. The TBCs with the bond coats prepared by the APS, HVOF and LPPS methods were fully delaminated (>50% after 159, 36, and 46 cycles, respectively, during the thermal-shock tests. The TGO thickness in the TBCs was strongly dependent on the both exposure time and temperature difference tested. The hardness values were found to be increased only after the CFTF, and the TBC with the bond coat prepared by the APS showed the highest adhesive strength before and after the FTF.

  16. Effect of TiB2 Additives on Wear Behavior of NiCrBSi-Based Plasma-Sprayed Coatings

    Directory of Open Access Journals (Sweden)

    Oleksandr UMANSKYI

    2016-05-01

    Full Text Available The influence of titanium diboride additives on microstructure and wear-resistance of NiCrBSi thermally sprayed coatings deposited on a steel substrate has been studied. NiCrBSi-based composite powders with 10, 20, 40 wt.% TiB2 particles content were produced. The structure of NiCrSiB-TiB2 coatings consists of TiB2 and CrB grains distributed in Ni-based matrix. The wear-resistance of NiCrSiB-TiB2 plasma sprayed coatings in dry sliding conditions against the same coating using pin-on-disk tester. It was determined that the amount of titanium diboride particles in  NiCrBSi-based coatings influences essentially on the wear  resistance and wear mechanism. The NiCrBSi-based plasma sprayed coatings containing 20 wt. % of TiB2 possess the highest wear resistance due to the realization of mechano-oxidational wear mechanism.DOI: http://dx.doi.org/10.5755/j01.ms.22.1.7307

  17. Influence of Oxidation Behavior of Feedstock on Microstructure and Ablation Resistance of Plasma-Sprayed Zirconium Carbide Coating

    Science.gov (United States)

    Hu, Cui; Ge, Xuelian; Niu, Yaran; Li, Hong; Huang, Liping; Zheng, Xuebin; Sun, Jinliang

    2015-10-01

    Plasma spray is one of the suitable technologies to deposit carbide coatings with high melting point, such as ZrC. However, in the spray processes performed under atmosphere, oxidation of the carbide powder is inevitable. To investigate the influence of the oxidation behavior of feedstock on microstructure and ablation resistance of the deposited coating, ZrC coatings were prepared by atmospheric and vacuum plasma spray (APS and VPS) technologies, respectively. SiC-coated graphite was applied as the substrate. The obtained results showed that the oxidation of ZrC powder in APS process resulted in the formation of ZrO and Zr2O phases. Pores and cracks were more likely to be formed in the as-sprayed APS-ZrC coating. The VPS-ZrC coating without oxides possessed denser microstructure, higher thermal diffusivity, and lower coefficients of thermal expansion as compared with the APS-ZrC coating. A dense ZrO2 layer would be formed on the surface of the VPS-ZrC-coated sample during the ablation process and the substrate can be protected sufficiently after being ablated in high temperature plasma jet. However, the ZrO2 layer, formed by oxidation of the APS-ZrC coating having loose structure, was easy to be washed away by the shearing action of the plasma jet.

  18. Influence of Cold-Sprayed, Warm-Sprayed, and Plasma-Sprayed Layers Deposition on Fatigue Properties of Steel Specimens

    Science.gov (United States)

    Cizek, J.; Matejkova, M.; Dlouhy, I.; Siska, F.; Kay, C. M.; Karthikeyan, J.; Kuroda, S.; Kovarik, O.; Siegl, J.; Loke, K.; Khor, Khiam Aik

    2015-06-01

    Titanium powder was deposited onto steel specimens using four thermal spray technologies: plasma spray, low-pressure cold spray, portable cold spray, and warm spray. The specimens were then subjected to strain-controlled cyclic bending test in a dedicated in-house built device. The crack propagation was monitored by observing the changes in the resonance frequency of the samples. For each series, the number of cycles corresponding to a pre-defined specimen cross-section damage was used as a performance indicator. It was found that the grit-blasting procedure did not alter the fatigue properties of the steel specimens (1% increase as compared to as-received set), while the deposition of coatings via all four thermal spray technologies significantly increased the measured fatigue lives. The three high-velocity technologies led to an increase of relative lives to 234% (low-pressure cold spray), 210% (portable cold spray), and 355% (warm spray) and the deposition using plasma spray led to an increase of relative lives to 303%. The observed increase of high-velocity technologies (cold and warm spray) could be attributed to a combination of homogeneous fatigue-resistant coatings and induction of peening stresses into the substrates via the impingement of the high-kinetic energy particles. Given the intrinsic character of the plasma jet (low-velocity impact of semi/molten particles) and the mostly ceramic character of the coating (oxides, nitrides), a hypothesis based on non-linear coatings behavior is provided in the paper.

  19. Synthesis of mullite coatings by chemical vapor deposition

    Energy Technology Data Exchange (ETDEWEB)

    Mulpuri, R.P.; Auger, M.; Sarin, V.K. [Boston Univ., MA (United States)

    1996-08-01

    Formation of mullite on ceramic substrates via chemical vapor deposition was investigated. Mullite is a solid solution of Al{sub 2}O{sub 3} and SiO{sub 2} with a composition of 3Al{sub 2}O{sub 3}{circ}2SiO{sub 2}. Thermodynamic calculations performed on the AlCl{sub 3}-SiCl{sub 4}-CO{sub 2}-H{sub 2} system were used to construct equilibrium CVD phase diagrams. With the aid of these diagrams and consideration of kinetic rate limiting factors, initial process parameters were determined. Through process optimization, crystalline CVD mullite coatings have been successfully grown on SiC and Si{sub 3}N{sub 4} substrates. Results from the thermodynamic analysis, process optimization, and effect of various process parameters on deposition rate and coating morphology are discussed.

  20. Mullite coatings for corrosion protection of silicon carbide

    Energy Technology Data Exchange (ETDEWEB)

    Mulpuri, R.; Sarin, V.K. [Boston Univ., MA (United States)

    1995-08-01

    SiC based ceramics have been identified as the leading candidate materials for elevated temperature applications in harsh oxidation/corrosion environments. It has been established that a protective coating can be effectively used to avoid problems with excessive oxidation and hot corrosion. However, to date, no coating configuration has been developed that can satisfy the stringent requirements imposed by such applications. Chemical Vapor Deposited (CVD) mullite coatings due to their desirable properties of toughness, corrosion resistance, and a good coefficient of thermal expansion match with SiC are being investigated as a potential candidate. Since mullite has never been successfully grown via CVD, the thermodynamics and kinetics of its formation were initially established and used as a guideline in determining the initial process conditions. Process optimization was carried out using an iterative process of theoretical analysis and experimental work coupled with characterization and testing. The results of theoretical analysis and the CVD formation characteristics of mullite are presented.

  1. Microstructure and properties of sintered mullite developed from Indian bauxite

    Indian Academy of Sciences (India)

    H S Tripathi; A Ghosh; M K Halder; B Mukherjee; H S Maiti

    2012-08-01

    Dense mullite aggregates with 72% Al2O3 have been synthesized by reaction sintering of two varieties of Indian bauxite and silica sol. The bauxites used are of inferior grade with different levels of accessory impurities such as Fe2O3, TiO2, CaO. The phase and microstructure development of sintered samples were investigated by XRD and SEM. It was found that morphology of the sintered grain is very much dependent on the impurity level. Mullite formed from bauxite-1 with low impurity is mostly equiaxed, whereas mullite developed from bauxite 2 with higher impurity particularly CaO is needle shaped. Presence of CaO in bauxite was found to be more detrimental than TiO2 and Fe2O3.

  2. Development of CVD Mullite Coatings for SiC Fibers

    Energy Technology Data Exchange (ETDEWEB)

    Sarin, V.K.; Varadarajan, S.

    2000-03-15

    A process for depositing CVD mullite coatings on SiC fibers for enhanced oxidation and corrosion, and/or act as an interfacial protective barrier has been developed. Process optimization via systematic investigation of system parameters yielded uniform crystalline mullite coatings on SiC fibers. Structural characterization has allowed for tailoring of coating structure and therefore properties. High temperature oxidation/corrosion testing of the optimized coatings has shown that the coatings remain adherent and protective for extended periods. However, preliminary tests of coated fibers showed considerable degradation in tensile strength.

  3. Mullite Continuous Ceramic Fiber Prepared by Sol—Gel Method

    Institute of Scientific and Technical Information of China (English)

    LIQuan; LIJing-hua; 等

    1995-01-01

    As oxide materials,continuous mullite fiber has superior properties in high temperature resis-tance when exposed in air,Present work shows the production of oxide solutio and the spinning of the nullite fiber,The stable spinning lasted over 10 hours,The strength of the mullite-based fiber is 1900 MPa with a diameter of 10μm after about 1000℃ treatment,When the treatment temperature exceeds 1300℃ the grains of fiber become column crystals and results in reduction of fiber strength.

  4. Effect of bauxite addition on densification and mullitization behaviour of West Bengal clay

    Indian Academy of Sciences (India)

    N S Raut; P Biswas; T K Bhattacharya; K Das

    2008-12-01

    The effect of bauxite addition on the densification and mullitization of reaction sintered bauxite–clay mixture had been studied in the temperature range 1400–1500°C. The maximum bulk density (2.89 g/cc) and minimum apparent porosity (0.58%) was achieved by addition of 50 wt% bauxite. The impurities present in bauxite and clay formed liquid phase which helped in particle diffusion to aid densification. The X-ray diffraction of sample fired at 1500°C showed cristoballite phase gradually disappearing and at the same time mullite and -Al2O3 phase appearing at a higher level of bauxite addition. The in situ nascent alumina formed was reactive that facilitated the formation of secondary mullite by solution precipitation mechanism. The presence of bauxite also changed the morphology of the mullite particles. Two types of mullite were distinctly observed in the SEM photographs: elongated primary mullite and equiaxed secondary mullite.

  5. Significance of in-situ dry-ice blasting on the microstructure, crystallinity and bonding strength of plasma-sprayed hydroxyapatite coatings.

    Science.gov (United States)

    Dong, Shujuan; Zeng, Jinyan; Li, Lifen; Sun, Junbin; Yang, Xiong; Liao, Hanlin

    2017-03-07

    To obtain hydroxyapatite (HA) coatings with high crystallinity which have long-term stability in clinical applications, coarse powders were usually injected to less energetic plasma. However, the HA coatings accumulated by partly melted particles usually have high porosity and poor mechanical properties, especially poor bonding strength. In this work, by profiting its quenching and mechanical impact, dry-ice blasting was in-situ employed during plasma spray process to improve the microstructure characterization and bonding strength of HA coatings. In addition, the influence of in-situ dry-ice blasting on the phase composition and crystallinity of plasma-sprayed HA coatings was investigated. The results show that a significant reduction of porosity and an apparent increase in bonding strength are revealed in plasma-sprayed HA coatings due to the cleaning effect of dry-ice blasting on the convex unmelted particles and splashing fragments. HA coatings prepared by the combination process of plasma spraying and dry-ice blasting have a compromise structure with minimum globular pores but with pronounced microcracks. The disappearance of CaO phase and the increase in crystallinity also derive from the application of dry-ice blasting.

  6. Surface Coating of NiTi Shape Memory Alloys with Calcium Phosphates by Dip-coating or Plasma-spraying-biological Characterization Examined by in vitro Testing Methods

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    The influence of different surface coatings of NiTi shape memory alloys was examined using in vitro testing methods. Plates of superelastic nickel-titanium shape memory alloy (NiTi) were coated with calcium phosphates (hydroxyapatite) by high-temperature plasma-spraying or by dip-coating. The biocompatibility was tested in vitro by cultivation of isolated human granulocytes and whole blood cells. As substrates, pure NiTi,plasma-spray-coated NiTi and dip-coated NiTi were used. Isolated granulocytes showed an increased adhesion to both calcium phosphate-coated NiTi samples. Compared to non-coated NiTi or dip-coated NiTi, the number of dead granulocytes adherent to plasma-sprayed surfaces was significantly increased (p < 0.01). Whether the differences in apoptosis of granulocytes on dip-coated vs plasma-sprayed coatings observed are due to differences in material surface morphologies bas to be analyzed in further studies. Because of the cellular interactions with the coating layers, it is likely that the results obtained are not caused by the underlying NiTi but due to the coating itself.

  7. Preparation and Characterization of Fe2O3-SiO2-Y2O3-Al2O3 Ferromagnetic Glass Ceramics Microspheres for Hyperthermia Application%热疗用Fe2O3-SiO2-Y2O3-Al2O3微晶玻璃微球的制备与性能

    Institute of Scientific and Technical Information of China (English)

    张佶颖; 王德平; 黄文旵

    2011-01-01

    采用火焰漂浮法制备新型含钇铁磁微晶玻璃微球(ferromagnetic glass ceramic microspheres,FGCMs),用以放疗与热疗相结合的医疗用途.通过热分析和X射线衍射(X-ray diffraction,XRD)研究热处理温度对FGCMs性能的影响.使用偏光显微镜观察FC-CMs的形貌.用振动样品磁强计(vibrating sample magnetometer,VSM)和磁热测试装置研究FGCMs的磁性能和磁热性能.通过XRD和VSM数据计算样品中微晶相的含量.用比发热量和比能量吸收率表征FGCMs的发热能力.实验结果表明:FGCMs有很大的应用前景,可用于热疗-放疗联合治疗肿瘤.%Novel ferromagnetic glass ceramic microspheres (FGCMs) containing yttrium which can be used for clinical applications combining features of radiotherapy and hyperthermia were prepared by heat treatment and flame spray method. Influence of the heat treatment of ferromagnetic glass ceramic was investigated by the differential thermal analysis (DTA) and X-ray diffraction (XRD).Morphology of the FGCMs was characterized by the polarizing microscopy. Magnetism property and heating power of the FGCMs were measured by a vibrating sample magnetometry(VSM) and a thermomagnetic measurement equipment, respectively. Amount of crystallized magnetite was calculated by the XRD and VSM data. Specific heat values and specific absorption rate values of the FGCMs was calculated to characterize the heating ability of the FGCMs. The experimental results show that the FGCMs have great potential to offer the dual-function of hyperthermia and radiotherapy in the treatment of cancer.

  8. Industrial Preparation of Bauxite-based Mullite Raw Material

    Institute of Scientific and Technical Information of China (English)

    YANG Zhongzheng; DING Baohua

    2008-01-01

    Bauxite-based mullite grogs were prepared with grade II bauxite(≤3mm)and coal gangue(≤3mm)as starting materials with formula of w(Al2O3)=68%~72%.Mill the mixture to particle size≤0.044mm by wet milling to homogenize chemical composition. After shaping by wet extrusion and drying, the materials were fired at 1550℃, 1600℃ and 1700℃ for 6 hours respectively. After cooling apparent porosity and bulk density of fired materials were tested. The results show as follows: the appropriate sintering temperature for bauxite-based mullite with homogeneous and consistent composition and microstructure and properties is 1600℃,at which the mullite has apparent porosity≤1.5%,bulk density≥2.81g·cm-3and refractoriness under load is 1610-1650℃.Compared with the laboratory results, the sintering temperature is lowered about 100℃,bulk density increased 0.06g?cm-3.The industrial feasibility of preparing bauxite-based mullite grogs with the processing is confirmed.

  9. Thermal cycling characteristics of plasma synthesized mullite films

    Energy Technology Data Exchange (ETDEWEB)

    Monteiro, O.R.; Hou, P.Y.; Brown, I.G. [Lawrence Berkeley National Lab., CA (United States)

    1997-12-01

    The authors have developed a plasma-based technique for the synthesis of mullite and mullite-like films on silicon carbide substrate material. The method, which they refer to as MePIIID (for Metal Plasma Immersion Ion Implantation and Deposition), uses two vacuum arc plasma sources and simultaneous pulse biasing of the substrate in a low pressure oxygen atmosphere. The Al:Si ratio can be controlled via the separate plasma guns, and the film adhesion, structure and morphology can be controlled via the ion energy which in turn is controlled by the pulse bias voltage. The films are amorphous as-deposited, and crystalline mullite is formed by subsequent annealing at 1000 C for 2 hours in air. Adhesion between the aluminum-silicon oxide film and the substrate increases after this first annealing. They have tested the behavior of films when subjected to repetitive thermal cycling between room temperature and 1100 C, and found that the films retain their adhesion and quality. Here they review the plasma synthesis technique and the characteristics of the mullite films prepared in this way, and summarize the status of the thermal cycling experiments.

  10. Induction of osteoconductivity by BMP-2 gene modification of mesenchymal stem cells combined with plasma-sprayed hydroxyapatite coating

    Science.gov (United States)

    Wu, Jiang; Guo, Ying-qiang; Yin, Guang-fu; Chen, Huai-qing; Kang, Yunqing

    2008-11-01

    Success in bone implant depends greatly on the composition and surface features of the implant. The surface-modification measures not only favor the implant's osteoconductivity, but also promote both bone anchoring and biomechanical stability. This paper reports an approach to combine a hydroxyapatite (HA) coated substrate with a cellular vehicle for the delivery of bone morphogenetic protein-2 (BMP-2) synergistically enhancing the osteoconductivity of implant surfaces. We examined the attachment, growth and osteoinductive activity of transfected BMP-producing bone marrow mesenchymal stem cells (BMSCs) on a plasma-sprayed HA coated substrate. It was found that the HA coated substrate could allow the attachment and growth of BMP-2 gene modified BMSCs, and this combined application synergistically enhanced osteconductivity of the substrate surface. This synergistic method may be of osseointegration value in orthopedic and dental implant surgery.

  11. Suspension Plasma-Sprayed ZnFe2O4 Nanostructured Coatings for ppm-Level Acetone Detection

    Science.gov (United States)

    You, Jiajun; Chen, Xia; Zheng, Bingbing; Geng, Xin; Zhang, Chao

    2017-02-01

    Zinc ferrite (ZnFe2O4) sensitive coatings have been deposited by suspension plasma spraying. The phase constitution of the coatings was characterized by x-ray diffraction while the top surface and cross-sectional morphology of the coatings were inspected by scanning electron microscopy. The response to acetone was tested with the concentration in the range of 25-500 ppm at the working temperature from 175 to 275 °C. The sensors that were deposited at an arc current of 400 A showed better performance than those at 600 A owing to small grain size and high porosity. The sensor response increased with acetone concentration. The optimized sensors showed excellent response/recovery time and selectivity to acetone at 200 °C.

  12. Deposition and properties of high-velocity-oxygen-fuel and plasma-sprayed Mo-Mo2C composite coatings

    Science.gov (United States)

    Prchlik, L.; Gutleber, J.; Sampath, S.

    2001-12-01

    Molybdenum thermal-spray coatings, dispersion strengthened by molybdenum oxides and molybdenum carbides, play an important role in industrial tribological applications. Traditionally, they have been prepared by plasma and wire flame spraying. High porosity and lower cohesion strength limit their application in situations where both galling and abrasion wear is involved. In this study, high-velocity-oxygen-fuel (HVOF) deposition of molybdenum and molybdenum carbide coatings was attempted. Deposition was achieved for all powders used. Composition, microstructure, mechanical, and wear properties of the HVOF synthesized coatings were evaluated and compared with plasma-sprayed counterparts. The HVOF coatings possessed a very good abrasion resistance, whereas plasma deposits performed better in dry sliding tests. Measurements showed a close relationship between the coating surface hardness and its abrasion resistance. Results also suggested correlation between molybdenum carbide distribution in the molybdenum matrix and the sliding friction response of Mo-Mo2C coatings.

  13. Electrochemical corrosion and metal ion release from Co-Cr-Mo prosthesis with titanium plasma spray coating.

    Science.gov (United States)

    Reclaru, Lucien; Eschler, Pierre-Yves; Lerf, Reto; Blatter, Andreas

    2005-08-01

    The corrosion behavior of CoCrMo implants with rough titanium coatings, applied by different suppliers by either sintering or vacuum plasma spraying, has been evaluated and compared with uncoated material. The open-circuit potential, corrosion current and polarization resistance were determined by electrochemical techniques. The Co, Cr and Ti ions released from the samples into the electrolyte during a potentiostatic extraction technique were analyzed using ICP-MS. The Ti coatings from the different suppliers showed a different porous morphology, and the implants exhibited a distinct corrosion activity, underlining the importance of the coating process parameters. Among the titanium coated samples, the one with the sintered overcoat turned out to be the most resistant. Yet, on an absolute scale, they all showed a corrosion resistance inferior to that of uncoated CoCrMo or wrought titanium.

  14. Evaluation of the behavior of shrouded plasma spray coatings in the platen superheater of coal-fired boilers

    Science.gov (United States)

    Sidhu, Buta Singh; Prakash, S.

    2006-06-01

    Nickel- and cobalt-based coatings were formulated by a shrouded plasma spray process on boiler tube steels, namely, ASTM-SA210-grade A1 (GrA1), ASTM-SA213-T-11 (T11), and ASTM-SA213-T-22 (T22). The Ni-22Cr-10Al-1Y alloy powder was sprayed as a bond in each case before the final coating. The degradation behavior of the bared and coated steels was studied in the platen superheater of the coal-fired boiler. The samples were inserted through the soot blower dummy points with the help of stainless steel wires. The coatings were found to be effective in increasing resistance to degradation in the given boiler environment. The maximum protection was observed in the case of Stellite-6 (St-6) coating.

  15. Evaluation of the behavior of shrouded plasma spray coatings in the platen superheater of coal-fired boilers

    Energy Technology Data Exchange (ETDEWEB)

    Sidhu, B.S.; Prakash, S. [GZS College of Engineering & Technology, Bathinda (India). Dept. of Mechanical Engineering

    2006-06-15

    Nickel- and cobalt-based coatings were formulated by a shrouded plasma spray process on boiler tube steels, namely, ASTM-SA210-grade A1 (GrA1), ASTM-SA213-T-11 (T11), and ASTM-SA213-T-22 (T22). The Ni-22Cr-10A1-1Y alloy powder was sprayed as a bond in each case before the final coating. The degradation behavior of the bared and coated steels was studied in the platen superheater of the coal-fired boiler. The samples were inserted through the soot blower dummy points with the help of stainless steel wires. The coatings were found to be effective in increasing resistance to degradation in the given boiler environment. The maximum protection was observed in the case of Stellite-6 (St-6) coating.

  16. Optimizing Compliance and Thermal Conductivity of Plasma Sprayed Thermal Barrier Coatings via Controlled Powders and Processing Strategies

    Science.gov (United States)

    Tan, Yang; Srinivasan, Vasudevan; Nakamura, Toshio; Sampath, Sanjay; Bertrand, Pierre; Bertrand, Ghislaine

    2012-09-01

    The properties and performance of plasma-sprayed thermal barrier coatings (TBCs) are strongly dependent on the microstructural defects, which are affected by starting powder morphology and processing conditions. Of particular interest is the use of hollow powders which not only allow for efficient melting of zirconia ceramics but also produce lower conductivity and more compliant coatings. Typical industrial hollow spray powders have an assortment of densities resulting in masking potential advantages of the hollow morphology. In this study, we have conducted process mapping strategies using a novel uniform shell thickness hollow powder to control the defect microstructure and properties. Correlations among coating properties, microstructure, and processing reveal feasibility to produce highly compliant and low conductivity TBC through a combination of optimized feedstock and processing conditions. The results are presented through the framework of process maps establishing correlations among process, microstructure, and properties and providing opportunities for optimization of TBCs.

  17. Numerical study of the spreading and solidification of a molten particle impacting onto a rigid substrate under plasma spraying conditions

    Directory of Open Access Journals (Sweden)

    Oukach Soufiane

    2015-01-01

    Full Text Available This paper deals with simulation of the spreading and solidification of a fully molten particle impacting onto a preheated substrate under traditional plasma spraying conditions. The multiphase problem governing equations of mass, momentum and energy conservation taking into account heat transfer by conduction, convection and phase change are solved by using a Finite Element approach. The interface between molten particle and surrounding air, is tracked using the Level Set method. The effect of the Reynolds number on the droplet spreading and solidification, using a wide range of impact velocities (40-250m/s, is reported. A new correlation that predicts the final spread factor of splat as a function of Reynolds number is obtained. Thermal contact resistance, viscous dissipation, wettability and surface tension forces effects are taken into account.

  18. Creep behavior of plasma sprayed NiCr and NiCrAl coating-based systems

    Institute of Scientific and Technical Information of China (English)

    Xiancheng ZHANG; Changjun LIU; Fuzhen XUAN; Zhengdong WANG; Shan-Tung TU

    2011-01-01

    The creep behavior of the plasma sprayed NiCr and NiCrAl coating/Nickel alloy 690substrate systems at 1033 K was investigated. Results showed that there was almost no difference in the creep lives between the NiCr and NiCrAl coated specimens at a given stress level, since the contents of Cr used in the NiCr and NiCrAl powders are almost same. The relationship between the minimum creep rate and the applied stress followed the well-known Norton's power law, εmin=Aσn, with the values of A=2.66× 10-16 Mpa-n.h-1 and n=6.48. The relation between the applied stress and time to rupture of the coated specimens can be estimated by using Larson-Miller equation. The θ projection method can be used to accurately characterize the creep behavior of the coated specimens.

  19. Apatite formation on alkaline-treated dense TiO2 coatings deposited using the solution precursor plasma spray process.

    Science.gov (United States)

    Chen, Dianying; Jordan, Eric H; Gell, Maurice; Wei, Mei

    2008-05-01

    A dense titania (TiO2) coating was deposited from an ethanol-based solution containing titanium isopropoxide using the solution precursor plasma spray (SPPS) process. XRD and Raman spectrum analyses confirmed that the coating is exclusively composed of rutile TiO2. SEM micrographs show the as-sprayed coating is dense with a uniform thickness and there are no coarse splat boundaries. The as-sprayed coating was chemically treated in 5M NaOH solution at 80 degrees C for 48 h. The bioactivity of as-sprayed and alkaline-treated coatings was investigated by immersing the coatings in simulated body fluid (SBF) for 14-28 days, respectively. After 28 days immersion, there is a complete layer of carbonate-containing apatite formed on the alkaline-treated TiO2 coating surface, but none formed on the as-sprayed coating.

  20. High Temperature Thermal Properties of Columnar Yttria Stabilized Zirconia Thermal Barrier Coating Performed by Suspension Plasma Spraying

    Science.gov (United States)

    Bernard, B.; Schick, V.; Remy, B.; Quet, A.; Bianchi, L.

    2016-09-01

    Performance enhancement of gas turbines is a main issue for the aircraft industry. Over many years, a large part of the effort has been focused on the development of more insulating Thermal Barrier Coatings (TBCs). In this study, Yttria Stabilized Zirconia (YSZ) columnar structures are processed by Suspension Plasma Spraying (SPS). These structures have already demonstrated abilities to get improved thermal lifetime, similarly to standard YSZ TBCs performed by EB-PVD. Thermal diffusivity measurements coupled with differential scanning calorimetry analysis are performed from room temperature up to 1100 °C, first, on HastelloyX substrates and then, on bilayers including a SPS YSZ coating. Results show an effective thermal conductivity for YSZ performed by SPS lower than 1 W.m-1K-1 whereas EB- PVD YSZ coatings exhibit a value of 1.5 W.m-1K-1.

  1. Microstructure and mechanical properties of plasma sprayed Al2O3 – 13%TiO2 Ceramic Coating

    Directory of Open Access Journals (Sweden)

    Wahab Juyana A

    2017-01-01

    Full Text Available This paper focused on the effect of deposition conditions on the microstructural and mechanical properties of the ceramic coating. In this study, Al2O3 – 13%TiO2 coated mild steel were prepared by using atmospheric plasma spray technology with different plasma power ranging from 25 kW to 40 kW. The as-sprayed coatings consist of γ-Al2O3 phase as the major phase and small amount of the titania phase existed in the coating structure. High degree of fully melted region was observed in the surface morphology for the coating sprayed with high plasma power, which lead to the high hardness and low percentage of porosity. In this study, nanoindentation test was carried out to investigate mechanical properties of the coating and the results showed that the coatings possess high elastic behaviour, which beneficial in engineering practice.

  2. 空气等离子镀覆技术的进展%Development of Air-plasma Spraying Technology

    Institute of Scientific and Technical Information of China (English)

    В.Я.Фролов; Г.К.Петров; Б.А.Юшин; Д.В.Иванов

    2014-01-01

    The air-plasma spraying technology has been found application in many fields .In recent years , research on both establishment of plasma generator and spraying process has been performed in the St .Petersburg State Polytechnic University , and many types of coatings , which may not only be used to protect freshly made parts but also to restore worn parts , have been developed .The theoretical and experimental investigations conducted by the St.Petersburg State Polytechnic University in conjunction with the Leibnits ( INP Greifswald ) Plasma and Technology Research Institute will allow amount of experimental work to be appreciably reduced in developing the plasma generator and the air-plasma spraying process .%空气等离子喷涂工艺在许多领域得到了应用。近年来,国立圣彼得堡综合技术大学在等离子体发生器的创建和涂覆工艺方面进行了研究,业已研制成多种涂层,既可用于新制零件的防护,也可用于磨损件的修复。国立圣彼得堡综合技术大学和雷波尼茨( INP Greifswald )等离子体及工艺研究院联合进行的理论和试验研究,可显著减少研发等离子体发生器和空气等离子涂覆工艺的试验工作量。

  3. The possibilities of atmospheric plasma-spraying application to obtain hydroxyapatite coatings on the stainless steel samples

    Directory of Open Access Journals (Sweden)

    Mihailović Marija D.

    2013-01-01

    Full Text Available For decades, the standard metallic materials for hip implants, besides the 316LVM stainless steel, were titanium- and cobalt/chromium-based alloys. Although bioinert, due to their corrosion resistance, they are not biocompatible. Contemporary surgical implants are not made just of bioinert metal anymore, but with deposited bioactive hydroxyapatite (HAp coating. Hydroxyapatite is chemically identical with the mineral constituent of bones and teeth, what besides its biocompatibility provides bioactivity as well. The HAp limitations are, however, weak tensile strength and low fatigue resistance for long term loadings, if used alone. This is the reason for HAp to be deposited onto the surgical implant, and to enable its bioactivity, what means intergrowth with bones, and therefore the long-lasting and mechanical stable non-cemented prosthesis. This is important predominantly because the need for such prostheses for younger population, and a better life quality. There are several contemporary techniques that have been used for deposition of these coatings onto the metal implant. The possibilities of atmospheric plasma-spraying for obtaining the stable HAp coatings on the 316LVM stainless steel, ordinary used as a standard material for hip implants production are presented in this paper. The coatings of a commercially available hydroxyapatite powder were plasma-sprayed onto the specimens of medical grade 316LVM stainless steel under various operating conditions. The optical microscopy was used for microstructure and porosity characterization, while coating morphology and Ca/P ratio were analyzed using SEM equipped with EDX. Coating microstructure varied from a porous to a glassy structure, depending on operating conditions applied and coating thickness. Coating porosity was determined to be at the lower required limit requested for the bone-coating intergrowth possibility, but nevertheless adhesion measurements showed good results. The Ca/P ratio was

  4. Effect of Composition on Mechanical Properties of Mullite-WC Nano Composites Prepared by Spark Plasma Sintering

    Directory of Open Access Journals (Sweden)

    H. Rajaei

    2016-12-01

    Full Text Available Mullite-WC composites were prepared from Mullite and WC powders by spark plasma sintering at 1400 °C for a holding time of 180 s under 30 MPa. Microstructure, strength, and hardness of the mullite-WC composites were studied. The mullite-WC composite containing 5-20 wt% WC reached over 94 % theoretical density. The strength and Vickers hardness of mullite-(10 wt% WC sintered composite reached maximum values of 298 MPa, and 1589 HV, respectively demonstrating that the introduction of WC significantly enhances the mechanical properties of the mullite matrix.

  5. Formation and characterization of mullite fibers produced by inviscid melt-spinning

    Science.gov (United States)

    Xiao, Zhijun

    IMS is a technique used to form fibers from low viscosity melts by means of stream stabilization in a reactant gas, in this case propane. Mullite (3Alsb2Osb3*2SiOsb2) was selected as the material to be fiberized. A stable mullite melt was obtained at 2000sp°C. Some short fibers and shot were formed in the fiber forming experiments. Crucible material selection is a prerequisite for proper application of the IMS technique. The effect of two crucible materials-graphite and boron nitride were studied. A carbothermal reaction occurred between the mullite melt and the graphite crucible. Boron nitride was selected as the crucible material because a relatively stable melt could be obtained. Operating environment is another factor that affects IMS mullite fiber formation. The effects of vacuum, nitrogen and argon on mullite melting behavior were studied. Argon gas was selected as the operating environment. A 2sp3 factorial design was developed to study the effect of such variables as temperature, holding time at the temperature, and heating rate on mullite melting behavior. The effects of the variables and interactions were calculated. Temperature has the biggest positive effect, holding time is the second, heating rate just has a very small negative effect. A detailed investigation of the mullite decomposition mechanism and kinetics was conducted in this work. A solid reaction mechanism was proposed. The kinetic results and IR analysis support the proposed mechanism. The carbon source inside the furnace led to the decomposition of mullite. A feasible experimental technique was developed to prevent the decomposition of mullite. The experiments with this design completely controlled the mullite decomposition. The short fibers, shot and some side products formed in the fiber forming experiments were characterized using XRD, XRF and SEM-EDS. The composition of the short fiber and shot was in the range of mullite composition. XRD showed that the diffraction pattern of shot is

  6. Difference of Mullite Whiskers between Ytterbia-Doped Aluminum Hydroxide-Silica Gel and Mechanochemical Process

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    A number of processing routes were developed for the synthesis of mullite whiskers. Mullite whiskers that were derived from ytterbia-doped aluminum hydroxide-silica gel were studied; another process for preparing mullite whiskers from Al2O3-SiO2 oxide mixtures by mechanochemical method was encountered by chance. The method of ytterbia-doped aluminum hydroxide-silica was used to enhance mullite formation from gel. For adding ytterbia, mullite formation can take place at 1000 ℃ and almost single-phase mullite can be achieved at 1150 ℃, which is a significantly lower temperature than mechanochemical method. This enhancement of mullite formation is also attributed to refinement of aluminum hydroxide-silica by gel. Furthermore, well-developed single-crystal mullite whiskers were produced from the gel powder instead of normal-shaped grains. The presence of YbO might have promoted the formation of nanosized Al2O3 particles, which then acted as a template leading to mullite whiskers at higher sintering temperature.

  7. Yttria-stabilized zirkonia / gadolinium zirconate double-layer plasma-sprayed thermal barrier coating systems (TBCs)

    Energy Technology Data Exchange (ETDEWEB)

    Bakan, Emine

    2015-07-01

    Thermal barrier coating (TBC) research and development is driven by the desirability of further increasing the maximum inlet temperature in a gas turbine engine. A number of new top coat ceramic materials have been proposed during the last decades due to limited temperature capability (1200 C) of the state-of-the-art yttria-stabilized zirconia (7 wt. % Y{sub 2}O{sub 3}-ZrO{sub 2}, YSZ) at long term operation. Zirconate pyrochlores of the large lanthanides((Gd → La){sub 2}Zr{sub 2}O{sub 7}) have been particularly attractive due to their higher temperature phase stability than that of the YSZ. Nonetheless, the issues related with the implementation of pyrochlores such as low fracture toughness and formation of deleterious interphases with thermally grown oxide (TGO, Al{sub 2}O{sub 3}) were reported. The implication was the requirement of an interlayer between the pyrochlores and TGO, which introduced double-layer systems to the TBC literature. Furthermore, processability issues of pyrochlores associated with the different evaporation rates of lanthanide oxides and zirconia resulting in unfavorable composition variations in the coatings were addressed in different studies. After all, although the material properties are available, there is a paucity of data in the literature concerning the properties of the coatings made of pyrochlores. From the processability point of view the most reported pyrochlore is La{sub 2}Zr{sub 2}O{sub 7}. Hence, the goal of this research was to investigate plasma-sprayed Gd{sub 2}Zr{sub 2}O{sub 7} (GZO) coatings and YSZ/GZO double-layer TBC systems. Three main topics were examined based on processing, performance and properties: (i) the plasma spray processing of the GZO and its impact on the microstructural and compositional properties of the GZO coatings; (ii) the cycling lifetime of the YSZ/GZO double-layer systems under thermal gradient at a surface temperature of 1400 C; (iii) the properties of the GZO and YSZ coatings such as

  8. Study for the Self—bonded High Performance Mullite Castable

    Institute of Scientific and Technical Information of China (English)

    LUYichun; LIZaigeng

    1996-01-01

    In order to overcome castables' innate imperfection from bond phase,we refer a so-called "self-bonded" phase to mullite castable using silica sol with the help of superfine powder as the bindr for fully exerting the merit of the perfect integrality of castable,The re-search work demonstrates that comparing with low-cement castable,this kind of "self-bonded" mullite castable is charterize by having perfect integrality of structure in the whole scope of test temperature,being very dense,and excellent in volume stability ,its porosity changing very little and smoothly,the cold and hot strengthes being high and stable,high temperature compressive creep little.This is a very promising castable structural refrctory.

  9. Effect of Liquid Feed-Stock Composition on the Morphology of Titanium Dioxide Films Deposited by Thermal Plasma Spray.

    Science.gov (United States)

    Adán, C; Marugán, J; van Grieken, R; Chien, K; Pershin, L; Coyle, T; Mostaghimi, J

    2015-09-01

    Titanium dioxide coatings were deposited on the surface of titanium foils by Thermal Plasma Spray (TPS) process. Three different TiO2 coatings were prepared using the commercial TiO2-P25 nanopowder and titanium isopropoxide precursor solution as feed-stocks. Structure and morphology of the TiO2-P25 powder and the plasma sprayed coatings were analyzed by X-ray diffraction (XRD), Raman spectroscopy, N2 adsorption-desorption isotherms, UV-visible spectroscopy and Scanning Electron Microscopy (SEM). XRD and Raman results indicate that the TiO2 coatings were composed of an anatase/rutile mixture that is conditioned by the suspension composition used to be sprayed. Coatings prepared from TiO2-P25 nanoparticles in water suspension (NW-P25) and titanium isopropoxide solution suspension (NSP-P25) are incorporated into the coatings without phase transformation and their anatase/rutile ratio percentage remains very similar to the starting TiO2-P25 powder. On the contrary, when titanium isopropoxide solution is used for spraying (SP), the amount of rutile increases in the final TiO2 coating. SEM analysis also reveals different microstructure morphology, coating thickness, density and porosity of the three TiO2 films that depend significantly on the type of feed-stock employed. Interestingly, we have observed the role of titanium isopropoxide in the formation of more porous and cohesive layers of TiO2. The NSP-P25 coating, prepared with a mix of titanium isopropoxide solution based on TiO2 nanoparticles, presents higher deposition efficiencies and higher coating thickness than the film prepared with nanoparticles suspended in water (NW-P25) or with titanium isopropoxide solutions (SP). This is due to the precursor solution is acting as the cement between TiO2 nanoparticles, improving the cohesive strength of the coating. In sum, NSP-P25 and NW-P25 coatings display a good photocatalytic potential, based on their light absorption properties and mechanical stability. Band gap of

  10. Microscopic, crystallographic and adherence properties of plasma-sprayed calcium phosphate coatings on Ti-6Al-4V

    Science.gov (United States)

    Tufekci, Eser

    Recently, plasma-spayed titanium implants have become very popular in the dentistry because of their biocompatibility and ability of providing osseointegration with the surrounding bone. Although there are numerous published studies on these materials, information and standards are still lacking. This study investigated the miscrostructural, crystallographic and adherence properties of plasma-sprayed hydroxyapatite coatings on Ti-6Al-4V substrates. The microstructures of the coatings and the elemental interdiffusion near the coating/substrate interface were investigated using a scanning electron microscope (SEM) equipped with x-ray energy-dispersive spectroscopy (EDS). X-ray diffraction analyses performed on Ti-6Al-4V coupons prepared with different percent crystallinities have provided structural information such as degree of crystallinity, phases present, average crystallite size, as well as the residual stresses within the coating. For evaluation of the adherence of the coatings to the substrates, experimental rods were subjected to torsion. The fracture surfaces were analyzed using SEM/EDS to develop a new methodology to determine the percent adherence of the coatings. SEM studies indicated that the surface microstructures of commercial dental implants were consistent with the plasma-spraying. In cross-section, coatings exhibited minimal porosity and limited interdiffusion of titanium and calcium at the coating/substrate interface. X-ray diffraction analyses indicated that the highest crystallinity coatings consisted of almost entirely HA and an amorphous calcium phosphate phase. As the coating crystallinity decreased, increasing amounts of alpha- and beta-tricalcium phosphate and tetracalcium phosphate were detected. The mean percent crystallinity for the three sets of coatings ranged from 50-60%. The mean HA crystallite size for the three sets of coatings ranged from about 0.02-0.04 mum. Differences in mean interplanar spacings for three selected

  11. 大气等离子喷涂氧化锆热障涂层研究进展%Research Progress of Atmospheric Plasma Sprayed Zirconia Thermal Barrier Coating

    Institute of Scientific and Technical Information of China (English)

    徐鹏; 宋仁国; 王超

    2011-01-01

    简要概述了大气等离子喷涂技术、等离子喷涂热障涂层选用氧化锆材料的原因及其具有的优异性能,同时也介绍了等离子喷涂制备热障涂层的国内外研究现状并指出了未来的发展方向.%The atmospheric plasma spraying and the reason of the choosing zirconia in the process of plasma sprayed thermal barrier coatings as well as its excellent performance were briefly overviewed. Meanwhile, the domestic and overseas research status of the plasma sprayed yttria partially stabilized zirconia (YSZ) thermal barrier coatings was also reviewed. Finally, the future development of plasma sprayed thermal barrier coatings was pointed out.

  12. Dielectric properties of Al2O3 coatings deposited via atmospheric plasma spraying and dry-ice blasting correlated with microstructural characteristics

    Science.gov (United States)

    Dong, Shujuan; Song, Bo; Liao, Hanlin; Coddet, Christian

    2015-01-01

    In this work, atmospheric plasma spraying combined with dry-ice blasting have been used to prepare alumina (Al2O3) coatings designed for insulating applications. The microstructural characteristics and dielectric properties of Al2O3 coatings were presented. The electrical insulating properties, i.e., dielectric strength and breakdown voltage, were investigated by dielectric breakdown test using direct current and alternating current. Relationships between dielectric properties and coating characteristics were discussed. The results showed that dry-ice blasting used during atmospheric plasma spray process allowed the production of coatings with better dielectric properties than those prepared without dry-ice blasting. The dielectric properties were correlated with the microstructural characteristics, not with phase composition.

  13. Study on the Mechanism of Adhesion Improvement Using Dry-Ice Blasting for Plasma-Sprayed Al2O3 Coatings

    Science.gov (United States)

    Dong, Shujuan; Song, Bo; Hansz, Bernard; Liao, Hanlin; Coddet, Christian

    2013-03-01

    The mechanisms of adhesion improvement of plasma-sprayed Al2O3 coatings using dry-ice blasting were investigated. In this study, the change of substrate surface characteristics in both the topography and the wettability due to the treatment of dry-ice blasting was mainly studied. The effect of dry-ice blasting on Al2O3 splat morphology with different treatment durations was also examined. The residual stress of plasma-sprayed Al2O3 coatings using dry-ice blasting was measured by curvature method and compared to that of coatings deposited with conventional air cooling. Based on these numerous assessment tests, it could be concluded that the adhesion improvement of Al2O3 coatings could be attributed to the cleaning effect of dry-ice blasting on different organic substances adsorbed on the substrates and the peening effect.

  14. Laser Remelting of Plasma Sprayed NiCrA1Y and NiCrAlY-A12O3 Coatings

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Two types of plasma sprayed coatings (NiCrAIY and NiCrAIY-AI2O3) were remelted by a 5 kW cw CO2 laser. With increasing laser power and decreasing traverse speed in the ranges of 200~700 W and 5~30 mm/s respectively, the melted track grew in width and depth. In the optimum range of laser parameters, a homogeneous remelted layer without voids, cavities, unmelted particles and microcracks was formed. On the surface of remelted layers, AI2O3 and YAIO3 were detected.As a result of isothermal oxidation tests, weight gains of laser remelted coatings were obviously lower than that only plasma sprayed, especially laser remelted NiCrAIY-AI2O3 coatings. The effects of laser remelting and incorporation of Al2O3 second phase in NiCrAIY matrix on high temperature oxidation resistance were discussed.

  15. Effect of Sealing Treatment on Corrosion Resistance of Plasma-Sprayed NiCrAl/Cr2O3-8 wt.%TiO2 Coating

    Science.gov (United States)

    Zhang, Jingjing; Wang, Zehua; Lin, Pinghua; Lu, Wenhuan; Zhou, Zehua; Jiang, Shaoqun

    2011-03-01

    Plasma-sprayed ceramic coatings inherently contain pores and micro-cracks which is deleterious when performed in aggressive environment. Various methods were applied to the as-sprayed coatings in order to improve the corrosion resistance. In the investigation of this study, plasma-sprayed NiCrAl/Cr2O3-8 wt.%TiO2 coatings were sealed by epoxy resin and silicone resin, respectively. Coatings were characterized by scanning electron microscopy/energy dispersive spectroscopy (SEM/EDS), optical microscopy (OM) and x-ray diffraction (XRD). The possible corrosion mechanism was discussed. The results of salt spray test and electrochemical measurements indicated that after the sealing treatment, the porosity of coatings decreased obviously and a compact layer was formed to protect the coating from corrosion. The silicone resin proved to be more effective than epoxy resin in enhancing the corrosion resistance of the coatings used in this research.

  16. Erosion-corrosion of as-plasma-sprayed and laser-remelted NiCrAlY bond coats in working conditions of a coal-fired boiler

    Energy Technology Data Exchange (ETDEWEB)

    Sidhu, B.S.; Prakash, S. [College of Engineering & Technology, Bathinda (India). Dept. of Mechanical Engineering

    2008-01-15

    Ni-22Cr-10Al-1Y plasma spray coating has been formulated on boiler tube steels. namely, low-carbon steel ASTM SA210-Grade A1. 1Cr-0.5Mo steel ASTM SA213-T-11, and 2.25Cr-1Mo steel ASTM SA213-T-22. The coated steels also have been laser-remelted using a Nd:YAG laser. The degradation behavior of as-sprayed and laser-remelted coatings have been evaluated in actual conditions in a coal-fired boiler for 1,000 h at 755{sup o}C. The laser remelting has been found to be effective to increase the degradation resistance of plasma-sprayed boiler steels. ASTM SA213-T-22-coated and laser-remelted steel has proved to be most effective in resistance to degrading species.

  17. Frictional properties of CeO$_{2}$-Al$_{2}$O$_{3}$-ZrO$_{2}$ plasma-sprayed film under mixed and boundary lubricating conditions

    CERN Document Server

    Kita, H; Osumi, K; 10.2109/jcersj.112.615

    2004-01-01

    In order to find a counterpart for reducing the frictional coefficient of Al/sub 2/O/sub 3/-ZrO/sub 2/-CeO/sub 2/ plasma-sprayed film, the sliding properties in mixed and boundary lubricating conditions was investigated. It was found that combination of a CrN- coated cast iron pin and an Al/sub 2/O/sub 3/-ZrO/sub 2/-CeO/sub 2/ plasma sprayed plate provided the lowest frictional coefficient among several combinations chosen from practical materials. The coefficient of friction was much lower than that of the materials combination widely used for piston ring and cylinder liner. It was inferred that the combination of a pin made of hard materials with high density, a smooth surface such as CrN-coated cast iron and a porous plate can reduce the frictional coefficient because less sliding resistance is implemented and porosity retains oil.

  18. Mullite/SiAlON/alumina composites by infiltration processing

    Energy Technology Data Exchange (ETDEWEB)

    Albano, M.P.; Scian, A.N. [Centro de Tecnologia de Recursos Minerales y Ceramica, Buenos Aires (Argentina)

    1997-01-01

    The formation of mullite/SiAlON/alumina composites was studied by infiltrating a SiAlON/alumina-base composite with two different solutions, followed by thermal treatment. The base composite was prepared from a mixture of tabular Al{sub 2}O{sub 3} grains, fume SiO{sub 2}, and aluminum powders. The mixture was pressed into test bars and nitrided in a nitrogen-gas (N{sub 2}) atmosphere at 1,480 C. The infiltrants were prehydrolyzed ethyl polysilicate solution and ethyl polysilicate-aluminum nitrate solution. The composites were infiltrated under vacuum, cured at 100 C, and precalcined in air at 700 C. This infiltration process was repeated several times to produce bars that had been subjected to multiple infiltrations, then the bars were calcined in a N{sub 2} atmosphere at 1,480 C to obtain mullite/SiAlON/alumina composites. The infiltration process increased the percentage of nitrogenous crystalline and mullite phases in the matrix; therefore, a decrease of the composite microporosity was observed. The infiltration increased the mechanical strength of the composites. Of the two composites, the one produced using prehydrolyzed ethyl polysilicate as the infiltrant had a higher mechanical strength, before and after being subjected to a severe thermal shock.

  19. Preparation of mullite fiber sol-gel method. Sol-gel ho ni yoru mullite sen prime i no gosei

    Energy Technology Data Exchange (ETDEWEB)

    Nishio, T. (Unichika Ltd., Osaka (Japan)); Fujiki, Y. (National Institute for Research and Inorganic Materials, Tsukuba (Japan))

    1991-08-01

    This report discribes a method to prepare mullite fiber by a new process using aqueous solution of aluminum nitrate, aluminum isopropoxide, and tetraethoxisilane(TEOS). Presursors of mullite were obtained by a method to add aluminum isopropoxide and TEOS simultaneously to the solution of aluminum nitrate, or by another method to add TEOS after adding aluminum isopropoxide. Then, structural analyses on the spinning solution, precursor fibers, and calcination process were carried out by {sup 27}Al- and {sup 29}Si-NMR, X-ray diffraction analysis, and DTA. The spinnable range of the method to add aluminum isopropoxide and TEOS at the same time was wider when it was shown with H{sub 2}O mol/(Al+Si)mol and Al(OPr{sup i}){sub 3} mol/Al(NO{sub 3}){sub 3} mol. Manifastation of spinnability deeply related to the bonding condition of Al and Si formed in the solution. 27 refs., 7 figs., 1 tab.

  20. Structure and magnetotransport properties in plasma-sprayed La 0.78Sr 0.22MnO 3 thick film

    Science.gov (United States)

    Orlando, M. T. D.; Cunha, A. G.; Freitas, J. C. C.; Orlando, C. G. P.; Bud'ko, S.; Giordanengo, B.; Sato, I. M.; Martinez, L. G.; Baggio-Saitovitch, E. M.

    2002-04-01

    Thick films of La 0.78Sr 0.22MnO 3 were produced by the plasma-spray technique onto stainless-steel substrate at 930°C. These films were obtained without the use of bond-layer, buffer-layer and annealing after deposition. The compound was deposited by a plasma-spray torch using nitrogen as the working gas. The films with thickness varying from 20 to 60 μm have good adherence and are composed of large splats with high degree of interconnection and small number of defects, as revealed by scanning electron microscopy. X-ray diffractometry analysis of the as-deposited film revealed that it had the same crystal structure as the original bulk. Measurements of electrical resistivity versus temperature for the film revealed a magnetic transition temperature near 340 K, with a ferromagnetic/metallic behavior below this temperature. The magnetoresistance of La 0.78Sr 0.22MnO 3 films exhibited similar magnetic field dependence as compared to the bulk sample, which indicates that the plasma-spray technique can be successfully employed for the deposition of thick films of manganites on large-area substrates while maintaining the main bulk properties.

  1. Role of process conditions on the microstructure, stoichiometry and functional performance of atmospheric plasma sprayed La(Sr)MnO3 coatings

    Science.gov (United States)

    Han, Su Jung; Chen, Yikai; Sampath, Sanjay

    2014-08-01

    Strontium doped lanthanum manganite (LSM) perovskite coatings were produced via atmospheric plasma spray technique to examine their applicability as electrically conductive coatings to protect chromium-poisoning of cathode side metallic interconnects in solid oxide fuel cells. Various plasma spray process conditions were manipulated including plasma power, total gas flow and content of H2 in the plasma gas in order to understand their effects on coating properties as well as efficacy as a protectant against Cr-poisoning. In-flight temperatures and velocities of spray particles were monitored for the various plasma spray conditions enabling assessment of thermal and kinetic energies of LSM particles. As anticipated, coating density improves with increasing thermal and/or kinetic energies of the LSM particles. However, the LSM particles also experienced significant phase decomposition at higher thermal exposure and longer residence time conditions. Due to preferential loss of oxygen and manganese, La2O3 phase is also formed under certain processing regimes. The resultant mixed-phase coating is ineffective both from electrical transport and as a protective coating for the metallic interconnect. Concomitantly, coatings with limited decomposition show excellent conductivity and protection characteristics demonstrating the need for mechanism driven process optimization for these functional oxide coatings.

  2. Corrosion resistance of plasma sprayed NiCrAl + (ZrO2 + Y2O3 ) thermal barrier coating on 18 -8 steel surface

    Institute of Scientific and Technical Information of China (English)

    CHEN Fei; L(U) Tao; DING Hua-dong; ZHOU Hai; LIU Kai

    2005-01-01

    The corrosion resistance of NiCrAl +(ZrO2 + Y2 O3 )thermal barrier coating, formed with the plasma spraying technique, on the 18 - 8 steel surface was investigated. The phase structure and morphology of the coating were analyzed by means of X-ray diffraction(XRD) and scanning electron microscopy(SEM). The electrochemical corrosion behavior of the coating in 1.0 mol/L H2 SO4 solution was studied by using electrochemical measurement methods. The results show that the gradient plasma spraying coating is composed of the NiCrAlY primer coating and the (ZrO2 + Y2O3 ) top coating, and the coating thickness is 360 μm. The microhardness of coating reaches 1 100 HV. The corrosion resistance of the plasma sprayed coating of the 18 - 8 steel surface is about 5 times as great as that of the original pattern. The corrosion resistance of the coating is enhanced notably.

  3. Chemical stability and antimicrobial activity of plasma sprayed bioactive Ca2ZnSi2O7 coating.

    Science.gov (United States)

    Li, Kai; Yu, Jiangming; Xie, Youtao; Huang, Liping; Ye, Xiaojian; Zheng, Xuebin

    2011-12-01

    Calcium silicate ceramic coatings have received considerable attention in recent years due to their excellent bioactivity and bonding strength. However, their high dissolution rates limit their practical applications. In this study, zinc incorporated calcium silicate based ceramic Ca(2)ZnSi(2)O(7) coating was prepared on Ti-6Al-4V substrate via plasma spraying technology aiming to achieve higher chemical stability and additional antibacterial activity. Chemical stability of the coating was assessed by monitoring mass loss and ion release of the coating after immersion in the Tris-HCl buffer solution and examining pH value variation of the solution. Results showed that the chemical stability of zinc incorporated coating was improved significantly. Antimicrobial activity of the Ca(2)ZnSi(2)O(7) coating was evaluated, and it was found that the coating exhibited 93% antibacterial ratio against Staphylococcus aureus. In addition, in vitro bioactivity and cytocompatibility were confirmed for the Ca(2)ZnSi(2)O(7) coating by simulated body fluid test, MC3T3-E1 cells adhesion investigation and cytotoxicity assay.

  4. Porous tantalum coatings prepared by vacuum plasma spraying enhance bmscs osteogenic differentiation and bone regeneration in vitro and in vivo.

    Directory of Open Access Journals (Sweden)

    Ze Tang

    Full Text Available Tantalum, as a potential metallic implant biomaterial, is attracting more and more attention because of its excellent anticorrosion and biocompatibility. However, its significantly high elastic modulus and large mechanical incompatibility with bone tissue make it unsuitable for load-bearing implants. In this study, porous tantalum coatings were first successfully fabricated on titanium substrates by vacuum plasma spraying (VPS, which would exert the excellent biocompatibility of tantalum and alleviate the elastic modulus of tantalum for bone tissue. We evaluated cytocompatibility and osteogenesis activity of the porous tantalum coatings using human bone marrow stromal cells (hBMSCs and its ability to repair rabbit femur bone defects. The morphology and actin cytoskeletons of hBMSCs were observed via electron microscopy and confocal, and the cell viability, proliferation and osteogenic differentiation potential of hBMSCs were examined quantitatively by PrestoBlue assay, Ki67 immunofluorescence assay, real-time PCR technology and ALP staining. For in vivo detection, the repaired femur were evaluated by histomorphology and double fluorescence labeling 3 months postoperation. Porous tantalum coating surfaces promoted hBMSCs adhesion, proliferation, osteogenesis activity and had better osseointegration and faster new bone formation rate than titanium coating control. Our observation suggested that the porous tantalum coatings had good biocompatibility and could enhance osseoinductivity in vitro and promote new bone formation in vivo. The porous tantalum coatings prepared by VPS is a promising strategy for bone regeneration.

  5. Mechanical Properties of Double-Layer and Graded Composite Coatings of YSZ Obtained by Atmospheric Plasma Spraying

    Science.gov (United States)

    Carpio, Pablo; Rayón, Emilio; Salvador, María Dolores; Lusvarghi, Luca; Sánchez, Enrique

    2016-04-01

    Double-layer and graded composite coatings of yttria-stabilized zirconia were sprayed on metallic substrates by atmospheric plasma spray. The coating architecture was built up by combining two different feedstocks: one micro- and one nanostructured. Microstructural features and mechanical properties (hardness and elastic modulus) of the coatings were determined by FE-SEM microscopy and nanoindentation technique, respectively. Additional adherence and scratch tests were carried out in order to assess the failure mechanisms occurring between the layers comprising the composites. Microstructural inspection of the coatings confirms the two-zone microstructure. This bimodal microstructure which is exclusive of the layer obtained from the nanostructured feedstock negatively affects the mechanical properties of the whole composite. Nanoindentation tests suitably reproduce the evolution of mechanical properties through coatings thickness on the basis of the position and/or amount of nanostructured feedstock used in the depositing layer. Adhesion and scratch tests show the negative effect on the coating adhesion of layer obtained from the nanostructured feedstock when this layer is deposited on the bond coat. Thus, the poor integrity of this layer results in lower normal stresses required to delaminate the coating in the adhesion test as well as minor critical load registered by using the scratch test.

  6. Plasma Spraying and Characterization of Tungsten Carbide-Cobalt Coatings by the Water-Stabilized System WSP

    Directory of Open Access Journals (Sweden)

    Pavel Ctibor

    2009-01-01

    Full Text Available Tungsten carbide-cobalt powders (WC-17wt% Co were plasma sprayed by a water-stabilized system WSP. Experiments with variable feeding distances and spray distances were carried out. Thinner coatings were deposited on carbon steel substrates and thicker coatings on stainless steel substrates to compare different cooling conditions. Basic characterization of coatings was done by XRD, SEM, and light microscopy plus image analysis. Microhardness was measured on polished cross-sections. The main focus of investigation was resistance against wear in dry as well as wet conditions. The appropriate tests were performed with set-ups based on ASTM G65 and G75, respectively. The influence of spray parameters onto coating wear performance was observed. The results of mechanical tests were discussed in connection with changes of phase composition and with the quality of the coating's microstructure. The results show that for obtaining the best possible WC-17Co coating with WSP process, from the viewpoint of wear resistance, the desired parameters combination is long feeding distance combined with short spray distance.

  7. Degradation behavior of Ni3Al plasma-sprayed boiler tube steels in an energy generation system

    Science.gov (United States)

    Sidhu, Buta Singh; Prakash, S.

    2005-06-01

    Boiler steels, namely, low-C steel, ASTM-SA210-Grade A1 (GrA1), 1Cr-0.5Mo steel, ASTM-SA213-T-11 (T11) and 2.25Cr-1Mo steel, ASTM-SA213-T-22 (T22) were plasma sprayed with Ni3Al. The alloy powder was prepared by mixing Ni and Al in the stoichiometric ratio of 3 to 1. The Ni-22Cr-10Al-1Y alloy powder was used as a bond coat, with a 150 µm thick layer sprayed onto the surface before applying the 200 µm coating of Ni3Al. Exposure studies have been performed in the platen superheater zone of a coal-fired boiler at around 755 °C for 10 cycles, each of 100 h duration. The protection to the base steel was minimal for the three steels. Scale spallation and the formation of a porous and nonadherent NiO scale were probably the main reasons for the lack of protection. In the case of T22-coated steel, cracks in the coatings have been observed after the first 100 h exposure cycle.

  8. Microstructure and Anticorrosion Property of AT13 Coatings Made by Combination of Nanoparticles Doping and Plasma Spraying Technique

    Institute of Scientific and Technical Information of China (English)

    LI Chun-fu; DAI Jia-lin; WANG Bin; ZHANG Ying; HE Tao-e; LUO Ping-ya

    2004-01-01

    Al2O3+13wt%TiO2 (AT13) particles were doped with 5%~30% nanoparticles and prefabricating powders were prepared by renewed granulation. AT13 coatings were prepared on the surface of steel 45# by air plasma spraying technique with the prefabricating powders. The microstructures of the AT13 prefabricating powders and the resulting coatings were investigated by SEM and EDS and XRD. The samples were undergone corrosion in the medium of 10% H2SO4 aqueous solution at temperature 80℃. The results indicate that the blistering time of coatings in the corrosive medium was increased with the increase of doped nanoparticle concentration while the time from blistering to spalling is independent of nanoparticle concentration. The results revealed that the structure of prefabricating powders was a twisted micrometer grade particle with dimension of 40-60μm, encapsulated by nanoparticles. The homogeneity of element distribution in coatings was improved and porosity was reduced. The phases of (Al2O3) 5.333 and orthorhombic Al2TiO5 were identified . The fracture analysis confirmed that there is a large amount of vermiculate whiskers with diameter of 10nm and length of 100~200 nm in coatings and the fracture type of coatings was the ductile trans-granular fracture.

  9. Microstructure and Anticorrosion Property of AT13 Coatings Made by Combination of Nanoparticles Doping and Plasma Spraying Technique

    Institute of Scientific and Technical Information of China (English)

    LIChun-fu; DAIJia-lin; WANGBin; ZHANGYing; HETao-e; LUOPing-ya

    2004-01-01

    Al2O3+ 13wt%TiO2 (AT13) particles were doped with 5%-30% nanoparticles and prefabricating powders were prepared by renewed granulation. AT13 coatings were prepared on the surface of steel 45# by air plasma spraying technique with the prefabricating powders. The microstructures of the AT13 prefabricating powders and the resulting coatings were investigated by SEM and EDS and XRD. The samples were undergone corrosion in the medium of 10% H2SO4 aqueous solution at temperature 80℃. The results indicate that the blistering time of coatings in the corrosive medium was increased with the increase of doped nanoparticle concentration while the time from blistering to spalling is independent of nanoparticle concentration.The results revealed that the structure of prefabricating powders was a twisted micrometer grade particle with dimension of 40-60μm, encapsulated by nanoparticles. The homogeneity of element distribution in coatings was improved and porosity was reduced. The phases of (Al2O3)5.333 and orthorhombic Al2TiO5 were identified. The fracture analysis confirmed that there is a large amount of vermiculate whiskers with diameter of 10nm and length of 100-200 nm in coatings and the fracture type of coatings was the ductile trans-granular fracture.

  10. Sliding Wear Behavior of Plasma Sprayed Alumina-Based Composite Coatings against Al2O3 Ball

    Institute of Scientific and Technical Information of China (English)

    Minh-quy Le; Young-hun Chae; Seock-sam Kim

    2004-01-01

    The sliding wear behaviors of a single layer Al2O3-30 wt pct ZrO2, a double layer Al2O3-30 wt pct ZrO2/Ni-Cr and a single layer Al2O3-13 wt pct TiO2 coating deposited on low carbon steel by plasma spraying were investigated under lubricated conditions with various normal loads. The plastic deformation, detachment and pull out of splats were involved in the wear process of the studied coatings under test conditions. Crack propagation was found in Al2O3-13 wt pct TiO2 under loads of 70 and 100 N and in Al2O3-30 wt pct ZrO2/Ni-Cr under a load of 130 N.While increasing the normal load, the wear rates of Al2O3-30 wt pct ZrO2 and Al2O3-30 wt pct ZrO2/Ni-Cr slightly increased, the wear rate of Al2O3-13 wt pct TiO2 increased rapidly. The results showed that the Ni-Cr bonding layer improved the wear resistance of the coating system even it is relatively thin compared with the outer coating layer.The influence of this bonding layer on wear behavior of the coating increased as increasing the normal load.

  11. Effect of substrate materials on rutile crystalline orientation in plasma-sprayed TiO2 coatings

    Institute of Scientific and Technical Information of China (English)

    YANG Guan-jun; LI Chang-jiu; WANG Yu-yue

    2004-01-01

    TiO2 coatings are of technical importance owing to their promising applications to photocatalytical, electrical, optical and tribological coatings. Thermal spraying process has been widely used to deposit both metallic and nonmetallic coatings. During thermal spraying, spray particle at fully or partially melted condition is projected to a substrate and subsequently flattens, rapidly cools and solidifies. Therefore, a coating in lamellar structure is usually formed as a quenched microstructure. TiO2 coatings were deposited on different substrates through plasma spraying with fused-crushed powder in rutile phase as feedstock to reveal the crystalline orientation in the coatings. XRD results show that the coatings consist of rutile phase with a fraction of anatase phase, and the rutile phase presents a preferable crystalline orientation along [101] direction. It is found that the orientation factors of rutile phase in the thin coatings are significantly influenced by substrate materials. The thick coatings yield the same orientation factors of 0.22 to 0.23 on all substrates in spite of substrate materials. It is considered that the thermal properties of substrate materials are the dominant factors for the preferable crystalline orientation in rutile phase within plasmasprayed TiO2 coating.

  12. Degradation behavior of Ni{sub 3}Al plasma-sprayed boiler tube steels in an energy generation system

    Energy Technology Data Exchange (ETDEWEB)

    Sidhu, B.S.; Prakash, S. [GZS, Bathinda (India). College of Engineering

    2005-06-01

    Boiler steels, namely, low-C steel, ASTM-SA210-Grade A1 (GrA1), 1Cr-0.5Mo steel, ASTM-SA213-T-11 (T11) and 2.25Cr-1Mo steel, ASTM-SA213-T-22 (T22) were plasma sprayed with Ni3Al. The alloy powder was prepared by mixing Ni and Al in the stoichiometric ratio of 3 to 1. The Ni-22Cr-10Al-1Y alloy powder was used as a bond coat, with a 150{mu} m thick layer sprayed onto the surface before applying the 200{mu}m coating of Ni{sub 3}Al. Exposure studies have been performed in the platen superheater zone of a coal-fired boiler at around 755{sup o}C for 10 cycles, each of 100 h duration. The protection to the base steel was minimal for the three steels. Scale spallation and the formation of a porous and nonadherent NiO scale were probably the main reasons for the lack of protection. In the case of T22-coated steel, cracks in the coatings have been observed after the first 100 h exposure cycle.

  13. Interfacial microstructures and hardness distributions of vacuum plasma spraying W-coated ODS ferritic steels for fusion plasma facing applications

    Energy Technology Data Exchange (ETDEWEB)

    Noh, Sanghoon, E-mail: shnoh@kaeri.re.kr [Nuclear Materials Division, Korea Atomic Energy Research Institute, Yuseong-gu, Daejeon (Korea, Republic of); Kasada, Ryuta; Kimura, Akihiko [Institute of Advanced Energy, Kyoto University, Gokasho, Uji, Kyoto (Japan); Nagasaka, Takuya [National Institute for Fusion Science, Toki, Gifu (Japan); Sokolov, Mikhail A. [Oak Ridge National Laboratory, Oak Ridge, TN (United States); Kim, Tae Kyu [Nuclear Materials Division, Korea Atomic Energy Research Institute, Yuseong-gu, Daejeon (Korea, Republic of)

    2014-04-15

    In the present study, interfacial microstructures and hardness distributions of W-coated ODS steels as plasma facing structural materials were investigated. A vacuum plasma spraying (VPS) technique was employed to fabricate a W layer on the surface of the ODS ferritic steel substrates. The microstructural observations revealed that the VPS-W has very fine grains aligned toward the spraying direction, and a favorable interface between W and ODS ferritic steels by a mechanical inter-locking without an intermetallic layer. However, crack-type defects were found in VPS-W. Because a brittle inter-diffused layer does not exist at the joint interface, the hardness was gradually distributed in the joint region. After neutron irradiation, irradiation hardening significantly occurred in the VPS-W. However, the hardening of VPS-W was less than that of bulk W irradiated at 773 K. Thus, the VPS is considered to be one of the promising ways to join dissimilar materials between W and ODS steels, which can avoid the formation of an interfacial intermetallic layer and create favorable irradiation hardening resistance on the W coated layer.

  14. Analysis of Plasma-Sprayed Thermal Barrier Coatings With Homogeneous and Heterogeneous Bond Coats Under Spatially Uniform Cyclic Thermal Loading

    Science.gov (United States)

    Arnold, Steven M.; Pindera, Marek-Jerzy; Aboudi, Jacob

    2003-01-01

    This report summarizes the results of a numerical investigation into the spallation mechanism in plasma-sprayed thermal barrier coatings observed under spatially-uniform cyclic thermal loading. The analysis focuses on the evolution of local stress and inelastic strain fields in the vicinity of the rough top/bond coat interface during thermal cycling, and how these fields are influenced by the presence of an oxide film and spatially uniform and graded distributions of alumina particles in the metallic bond coat aimed at reducing the top/bond coat thermal expansion mismatch. The impact of these factors on the potential growth of a local horizontal delamination at the rough interface's crest is included. The analysis is conducted using the Higher-Order Theory for Functionally Graded Materials with creep/relaxation constituent modeling capabilities. For two-phase bond coat microstructures, both the actual and homogenized properties are employed in the analysis. The results reveal the important contributions of both the normal and shear stress components to the delamination growth potential in the presence of an oxide film, and suggest mixed-mode crack propagation. The use of bond coats with uniform or graded microstructures is shown to increase the potential for delamination growth by increasing the magnitude of the crack-tip shear stress component.

  15. Microstructural Characteristics of Y2O3-MgO Composite Coatings Deposited by Suspension Plasma Spray

    Science.gov (United States)

    Muoto, Chigozie K.; Jordan, Eric H.; Gell, Maurice; Aindow, Mark

    2012-12-01

    Dense composite Y2O3-MgO coatings have been deposited by suspension plasma spray. Ethanol-based suspensions of powders synthesized by thermal decomposition of precursor solutions containing yttrium nitrate (Y[n]) and magnesium nitrate (Mg[n]) or magnesium acetate (Mg[a]) were selected as the feedstock; this gave powders with both phases in each particle, to inhibit phase segregation during solvent evaporation. The influence of powder characteristics on the microstructures of the coatings was investigated. The Y[n]Mg[a] suspension was more stable, with a better dispersion of the component phases than the Y[n]Mg[n] suspension. The coatings deposited using each suspension type exhibited lamellar structures comprising Y2O3 and MgO phases in wavy alternating streaks, with unmelted/semi-melted particles entrapped in the lamellae; this indicates that phase segregation still occurred in the molten state. Eutectic structures were formed in the coating generated using the Y[n]Mg[a] suspension, resulting from improved mixing of the component phases in the suspension powder.

  16. Double-Layer Gadolinium Zirconate/Yttria-Stabilized Zirconia Thermal Barrier Coatings Deposited by the Solution Precursor Plasma Spray Process

    Science.gov (United States)

    Jiang, Chen; Jordan, Eric H.; Harris, Alan B.; Gell, Maurice; Roth, Jeffrey

    2015-08-01

    Advanced thermal barrier coatings (TBCs) with lower thermal conductivity, increased resistance to calcium-magnesium-aluminosilicate (CMAS), and improved high-temperature capability, compared to traditional yttria-stabilized zirconia (YSZ) TBCs, are essential to higher efficiency in next generation gas turbine engines. Double-layer rare-earth zirconate/YSZ TBCs are a promising solution. From a processing perspective, solution precursor plasma spray (SPPS) process with its unique and beneficial microstructural features can be an effective approach to obtaining the double-layer microstructure. Previously durable low-thermal-conductivity YSZ TBCs with optimized layered porosity, called the inter-pass boundaries (IPBs) were produced using the SPPS process. In this study, an SPPS gadolinium zirconate (GZO) protective surface layer was successfully added. These SPPS double-layer TBCs not only retained good cyclic durability and low thermal conductivity, but also demonstrated favorable phase stability and increased surface temperature capabilities. The CMAS resistance was evaluated with both accumulative and single applications of simulated CMAS in isothermal furnaces. The double-layer YSZ/GZO exhibited dramatic improvement in the single application, but not in the continuous one. In addition, to explore their potential application in integrated gasification combined cycle environments, double-layer TBCs were tested under high-temperature humidity and encouraging performance was recorded.

  17. Influence of chloride ion concentration on immersion corrosion behaviour of plasma sprayed alumina coatings on AZ31B magnesium alloy

    Directory of Open Access Journals (Sweden)

    D. Thirumalaikumarasamy

    2014-12-01

    Full Text Available Corrosion attack of aluminium and magnesium based alloys is a major issue worldwide. The corrosion degradation of an uncoated and atmospheric plasma sprayed alumina (APS coatings on AZ31B magnesium alloy was investigated using immersion corrosion test in NaCl solutions of different chloride ion concentrations viz., 0.01 M, 0.2 M, 0.6 M and 1 M. The corroded surface was characterized by an optical microscope and X-ray diffraction. The results showed that the corrosion deterioration of uncoated and coated samples were significantly influenced by chloride ion concentration. The uncoated magnesium and alumina coatings were found to offer a superior corrosion resistance in lower chloride ion concentration NaCl solutions (0.01 M and 0.2 M NaCl. On the other hand the coatings and Mg alloy substrate were found to be highly susceptible to localized damage, and could not provide an effective corrosion protection in solutions containing higher chloride concentrations (0.6 M and 1 M. It was found that the corrosion resistance of the ceramic coatings and base metal gets deteriorated with the increase in the chloride concentrations.

  18. Application of atmospheric solution precursor plasma spray to photocatalytic devices for small and medium industries in developing countries

    Science.gov (United States)

    Kindole, Dickson; Ando, Yasutaka

    2017-01-01

    For development of a functional film deposition process with high deposition rate, as a basic study, TiO2 films were deposited by atmospheric solution precursor plasma spray (ASPPS) process. Ethanol-diluted titanium tetraisobutoxide [TTIB: Ti(OC4H9)4] was used as a feedstock. To achieve a high plasma thermal energy at a low discharge power, N2-dominant Ar/N2 as the plasma working gas was used, for film deposition at various deposition distances. Consequently, photocatalytic TiO2 with a rutile/anatase mixture film structure was deposited evenly in this case. By conducting methylene blue decomposition and wettability tests, photocatalytic properties of the film were confirmed. When a TiO2 film was applied to photocatalytic dye-sensitized solar cells (DSSCs), the cells generated an electromotive force of 0.143V oc, which is close to those of commercial DSSCs. From these results, the ASPPS process was found to have high potential for high rate functional film deposition and was cost effective, making it suitable for developing countries.

  19. A comparative study on solid particle erosion behavior of plasma sprayed Cr2O3 coatings on 410 grade steel

    Science.gov (United States)

    Sreenivas Rao, K. V.; Girisha, K. G.; Eswar, Sushruta

    2016-09-01

    In the present investigation chromium oxide (Cr2O3) powder particles were used to deposit on 410 martensitic steel. Ni-Cr was used as bond coat. Erosion studies were directed on uncoated and also plasma sprayed steel examples at room temperature. The Erosion analyses were done utilizing an air-jet erosion test rig at a speed of 30 m/s by varying stand-off distance as per ASTM G-76. The stand-off distance considered were 10mm, 20mm, 30mm & 40mm. Silica sand particles of size 312μm was used as erodent. The surface morphologies were characterized using Scanning electron microscope (SEM) and presence of coating material was confirmed using energy dispersive X-ray analyzer (EDS). Vickers micro harness test was performed on surface of coated and un-coated substrates. It was observed that Cr2O3 Coated specimen exhibits better Erosion resistance when contrasted with uncoated substrates because of its enhanced property like micro hardness.

  20. Microstructural features and properties of plasma sprayed YPSZ/NiCrAlY thermal barrier coating (TBC)

    Institute of Scientific and Technical Information of China (English)

    孙大谦; 王文权; 宣兆志; 宫文彪

    2004-01-01

    The plasma sprayed thermal barrier coating (TBC) consists of NiCrAlY bond coating and yttria partially stabilized zirconia (YPSZ) top coating. NiCrAlY coating mainly contains Ni solid solution with face centered cubic lattice, Al2O3 oxides and pores. The most obvious feature of YPSZ coating with tetragonal zirconia is a lot of vertical microcracks in this coating. The thermal insulation capability of the TBC increased with an increase in YPSZ coating thickness, the temperature drop across the TBC increasing from 60℃ to 92℃ with increasing YPSZ coating thickness with increasing YPSZ coating thickness and cracks initiated mainly in original vertical microcrack tips of the YPSZ coating and propagated not only along YPSZ coating / NiCrAlY coating interface but also through into two stages: transient oxidation stage with rapid oxidation rate and steady oxidation stage with slow oxidation. Their transition time was favorable to increase YPSZ coating toughness and to decrease the pores and oxides of the TBC system for improving thermal shock resistance and oxidation resistance of the TBC.

  1. Characterization and Wear Behavior of Heat-treated Ni3Al Coatings Deposited by Air Plasma Spraying

    Science.gov (United States)

    Mehmood, K.; Rafiq, M. A.; Nusair Khan, A.; Ahmed, F.; Mudassar Rauf, M.

    2016-07-01

    Air plasma spraying was utilized to deposit Ni3Al coatings on AISI-321 steel substrate. The deposited coatings were isothermally heat-treated at various temperatures from 500 to 800 °C for 10, 30, 60, and 100 h. The x-ray diffraction analysis revealed NiO formation in Ni3Al at 500 °C after 100 h, and the percentage of NiO increased with increasing exposure time and temperature. The hardness of the coating increased with the formation of NiO. The DSC test showed the formation of minor phases, Al3Ni and Al3Ni2, within the coating along with the major phase Ni3Al. TGA revealed a slowing down of the oxidation rate upon surface oxide formation. The pin-on-disk wear test on the as-sprayed and heat-treated coatings showed that wear rate and coefficient of friction decreased with an increase in the NiO phase content.

  2. Wear resistance and microstructural properties of Ni–Al/h-BN/WC–Co coatings deposited using plasma spraying

    Energy Technology Data Exchange (ETDEWEB)

    Hsiao, W.T. [Materials and Chemical Research Laboratories, Industrial Technology Research Institute, Chutung 310, Taiwan (China); Su, C.Y., E-mail: cysu@ntut.edu.tw [Graduate Institute of Manufacturing Technology, National Taipei University of Technology, Taipei 106, Taiwan (China); Huang, T.S. [China Steel Corporation, Kaohsiung, Taiwan (China); Liao, W.H. [Materials and Chemical Research Laboratories, Industrial Technology Research Institute, Chutung 310, Taiwan (China); Nano Technology Laboratory, Department of Materials Engineering, National Chung Hsing University, Taichung 402, Taiwan (China)

    2013-05-15

    Hexagonal boron nitride (h-BN) and tungsten carbide cobalt (WC–Co) were added to nickel aluminum alloy (Ni–Al) and deposited as plasma sprayed coatings to improve their tribological properties. The microstructure of the coatings was analyzed using a scanning electron microscope (SEM). Following wear test, the worn surface morphologies of the coatings were analyzed using a SEM to identify their fracture modes. The results of this study demonstrate that the addition of h-BN and WC–Co improved the properties of the coatings. Ni–Al/h-BN/WC–Co coatings with high hardness and favorable lubrication properties were deposited. - Highlights: • We mixed Ni–Al, h-BN and WC–Co powders and deposited them as composite coatings. • Adding WC–Co was found to increase the hardness and reduce the wear volume loss. • Adding h-BN was found to decrease the hardness and reduce the friction coefficient. • This composite coating was shown to have improved wear properties at 850 °C.

  3. Influence of in-flight particle state diagnostics on properties of plasma sprayed YSZ-CeO2 nanocomposite coatings

    Directory of Open Access Journals (Sweden)

    S. Mantry

    2014-07-01

    Full Text Available This article describes the influence of controlling in-flight hot particle characteristics on properties of plasma sprayed nanostructured yttria stabilized zirconia (YSZ coatings. This article depicts dependence of adhesion strength of as-sprayed nanostructured YSZ coatings on particle temperature, velocity and size of the splat prior to impact on the metallic substrate. Particle temperature measurement is based on two-color pyrometry and particle velocities are measured from the length of the particle traces during known exposure times. The microstructure and adhesion strength of as-sprayed nano-YSZ coatings were studied. Field emission scanning electron microscopy results revealed that morphology of coating exhibits bimodal microstructure consisting of nano-zones reinforced in the matrix of fully melted particles. The coating adhesion strength is noticed to be greatly affected by the melting state of agglomerates. Maximum adhesion strength of 42.39 MPa has been experimentally found out by selecting optimum levels of particle temperature and velocity. The enhanced bond strength of nano-YSZ coating may be attributed to higher interfacial toughness due to cracks being interrupted by adherent nano-zones.

  4. Phosphor-Doped Thermal Barrier Coatings Deposited by Air Plasma Spray for In-Depth Temperature Sensing.

    Science.gov (United States)

    Peng, Di; Yang, Lixia; Cai, Tao; Liu, Yingzheng; Zhao, Xiaofeng; Yao, Zhiqi

    2016-09-28

    Yttria-stabilized zirconia (YSZ)-based thermal barrier coating (TBC) has been integrated with thermographic phosphors through air plasma spray (APS) for in-depth; non-contact temperature sensing. This coating consisted of a thin layer of Dy-doped YSZ (about 40 µm) on the bottom and a regular YSZ layer with a thickness up to 300 µm on top. A measurement system has been established; which included a portable; low-cost diode laser (405 nm); a photo-multiplier tube (PMT) and the related optics. Coating samples with different topcoat thickness were calibrated in a high-temperature furnace from room temperature to around 900 °C. The results convincingly showed that the current sensor and the measurement system was capable of in-depth temperature sensing over 800 °C with a YSZ top layer up to 300 µm. The topcoat thickness was found to have a strong effect on the luminescent signal level. Therefore; the measurement accuracy at high temperatures was reduced for samples with thick topcoats due to strong light attenuation. However; it seemed that the light transmissivity of YSZ topcoat increased with temperature; which would improve the sensor's performance at high temperatures. The current sensor and the measurement technology have shown great potential in on-line monitoring of TBC interface temperature.

  5. Microstructural Effects and Properties of Non-line-of-Sight Coating Processing via Plasma Spray-Physical Vapor Deposition

    Science.gov (United States)

    Harder, Bryan J.; Zhu, Dongming; Schmitt, Michael P.; Wolfe, Douglas E.

    2017-08-01

    Plasma spray-physical vapor deposition (PS-PVD) is a unique processing method that bridges the gap between conventional thermal spray and vapor phase methods, and enables highly tailorable coatings composed of a variety of materials in thin, dense layers or columnar microstructures with modification of the processing conditions. The strengths of this processing technique are material and microstructural flexibility, deposition speed, and potential for non-line-of-sight (NLOS) capability by vaporization of the feedstock material. The NLOS capability of PS-PVD is investigated here using yttria-stabilized zirconia and gadolinium zirconate, which are materials of interest for turbine engine applications. PS-PVD coatings were applied to static cylindrical substrates approximately 6-19 mm in diameter to study the coating morphology as a function of angle. In addition, coatings were deposited on flat substrates under various impingement configurations. Impingement angle had significant effects on the deposition mode, and microscopy of coatings indicated that there was a shift in the deposition mode at approximately 90° from incidence on the cylindrical samples, which may indicate the onset of more turbulent flow and PVD-like growth. Coatings deposited at non-perpendicular angles exhibited a higher density and nearly a 2× improvement in erosion performance when compared to coatings deposited with the torch normal to the surface.

  6. Cyclic delamination behavior of plasma-sprayed hydroxyapatite coating on Ti-6Al-4V substrates in simulated body fluid.

    Science.gov (United States)

    Otsuka, Yuichi; Kawaguchi, Hayato; Mutoh, Yoshiharu

    2016-10-01

    This study aimed to clarify the effect of a simulated body fluid (SBF) on the cyclic delamination behavior of a plasma-sprayed hydroxapatite (HAp) coating. A HAp coating is deposited on the surfaces of surgical metallic materials in order to enhance the bond between human bone and such surfaces. However, the HAp coating is susceptible to delamination by cyclic loading from the patient's gait. Although hip joints are subjected to both positive and negative moments, only the effects of tensile bending stresses on vertical crack propagation behavior have been investigated. Thus, the cyclic delamination behavior of a HAp coating was observed at the stress ratio R=-1 in order to determine the effects of tensile/compressive loading on the delamination behavior. The delamination growth rate increased with SBF immersion, which decreased the delamination life. Raman spectroscopy analysis revealed that the selective phase dissolution in the HAp coating was promoted at interfaces. Finite element analysis revealed that the energy release rate Gmax showed a positive value even in cases with compressive loading, which is a driving force for the delamination of a HAp coating. A prediction model for the delamination growth life was developed that combines a fracture mechanics parameter with the assumed stress-dependent dissolution rate. The predicted delamination life matched the experimental data well in cases of lower stress amplitudes with SBF. Copyright © 2016 Elsevier B.V. All rights reserved.

  7. Improved Thermally Grown Oxide Scale in Air Plasma Sprayed NiCrAlY/Nano-YSZ Coatings

    Directory of Open Access Journals (Sweden)

    Mohammadreza Daroonparvar

    2013-01-01

    Full Text Available Oxidation has been considered as one of the principal disruptive factors in thermal barrier coating systems during service. So, oxidation behavior of thermal barrier coating (TBC systems with nanostructured and microstructured YSZ coatings was investigated at 1000∘C for 24 h, 48 h, and 120 h. Air plasma sprayed nano-YSZ coating exhibited a trimodal structure. Microstructural characterization also demonstrated an improved thermally grown oxide scale containing lower spinels in nano-TBC system after 120 h of oxidation. This phenomenon is mainly related to the unique structure of the nano-YSZ coating, which acted as a strong barrier for oxygen diffusion into the TBC system at elevated temperatures. Nearly continues but thinner Al2O3 layer formation at the NiCrAlY/nano-YSZ interface was seen, due to lower oxygen infiltration into the system. Under this condition, spinels formation and growth on the Al2O3 oxide scale were diminished in nano-TBC system compared to normal TBC system.

  8. Phosphor-Doped Thermal Barrier Coatings Deposited by Air Plasma Spray for In-Depth Temperature Sensing

    Directory of Open Access Journals (Sweden)

    Di Peng

    2016-09-01

    Full Text Available Yttria-stabilized zirconia (YSZ-based thermal barrier coating (TBC has been integrated with thermographic phosphors through air plasma spray (APS for in-depth; non-contact temperature sensing. This coating consisted of a thin layer of Dy-doped YSZ (about 40 µm on the bottom and a regular YSZ layer with a thickness up to 300 µm on top. A measurement system has been established; which included a portable; low-cost diode laser (405 nm; a photo-multiplier tube (PMT and the related optics. Coating samples with different topcoat thickness were calibrated in a high-temperature furnace from room temperature to around 900 °C. The results convincingly showed that the current sensor and the measurement system was capable of in-depth temperature sensing over 800 °C with a YSZ top layer up to 300 µm. The topcoat thickness was found to have a strong effect on the luminescent signal level. Therefore; the measurement accuracy at high temperatures was reduced for samples with thick topcoats due to strong light attenuation. However; it seemed that the light transmissivity of YSZ topcoat increased with temperature; which would improve the sensor’s performance at high temperatures. The current sensor and the measurement technology have shown great potential in on-line monitoring of TBC interface temperature.

  9. Microstructural development of melt-grown mullite fibrils

    Science.gov (United States)

    Baer, Amanda

    The crystallization behavior of mullite growing from the melt within a siliceous glassy phase has been investigated. Initial studies examined single crystal, nominally continuous mullite fibers grown in bundles by directional solidification using a modified version of the Edge-Defined Film-Fed Growth (EFG) process (GE-AE/Saphikon, Inc.). These fibers are intended to be recovered by dissolution of the glass matrix and used as reinforcements of ceramic matrix composites. Subsequent experiments employed small-scale crucible-based solidification experiments conducted at the UCSB Materials Processing Lab. The EFG approach yielded ribbons containing bundles of aligned single-crystal mullite with relatively small diameters embedded in a silicate glass matrix. Because of interactions between the growing crystals, however, the fibers recovered are actually discontinous crystals and hence termed "fibrils." Ribbons were produced from SiOsb2-Alsb2Osb3-MgO melts at solidification rates ranging from 2.5 to 61 cm/h. Typically, mullite fibers grew in the (001) direction and had distinct facets on the \\{110)-type planes. The mullite fibrils exhibited a variety of cross-sectional profiles-including various forms of glass-filled hollows, internal splintering, and lateral dendritic growth-which resulted largely from morphological instability during growth, and thus depended on the alloy composition and solidification parameters. Morphological instabilities became more pronounced with increasing growth velocity. Increasing the MgO content or the Alsb2Osb3/SiOsb2 ratio reduced these instabilities, indicating the role of alloy chemistry in modifying the transport properties in the melt, and hence the ease of solute redistribution. The crucible experiments examined the role of melt chemistry further, paying particular attention to the effects of various modifying additions to the SiOsb2-Alsb2Osb3 melt (MgO, BaO, Nasb2O, and Ksb2O). The choice of modifying oxide had a significant effect

  10. Preparation of mullite whiskers reinforced SiC/Al2O3 composites by microwave sintering

    Directory of Open Access Journals (Sweden)

    Wei Li

    2016-12-01

    Full Text Available Mullite whiskers reinforced SiC/Al2O3 composites were prepared by microwave sintering in a microwave chamber with TE666 resonant mode. Original SiC particles were coated with SiO2 using sol-gel processing and mixed with Al2O3 particles. Mullite was formed in the reaction between SiO2 and Al2O3. The isostatically pressed cylindrical pellets were sintered from 1350 °C to 1600 °C for 30 min. Physical and chemical responses were investigated by detecting changes in reflected power during the microwave sintering process. XRD was carried out to characterize the samples and showed that mullite could be formed at 1200 °C. Bridging of mullite whiskers between Al2O3 and SiC particles was observed by SEM and is due to a so-called local hot spot effect, which was the unique feature for microwave sintering. The optimized microwave sintering temperature was 1500 °C corresponding to the maximum amount of mullite whiskers within SiC/Al2O3 composites. The high electro-magnetic field enhanced the decomposition of mullite at higher temperatures above 1550 °C. The mechanical properties of mullite whiskers reinforced SiC/Al2O3 composites are much better than the SiC/Al2O3 composites without mullite whiskers.

  11. Copper ions removal from water using functionalized carbon nanotubes–mullite composite as adsorbent

    Energy Technology Data Exchange (ETDEWEB)

    Tofighy, Maryam Ahmadzadeh; Mohammadi, Toraj, E-mail: torajmohammadi@iust.ac.ir

    2015-08-15

    Highlights: • CNTs–mullite composite was prepared via chemical vapor deposition (CVD) method. • The prepared composite was modified with concentrated nitric acid and chitosan. • The modified CNTs–mullite composites were used as novel adsorbents. • Copper ion removal from water by the prepared adsorbents was performed. • Langmuir and Freundlich isotherms and two kinetic models were applied to fit the experimental data. - Abstract: Carbon nanotubes–mullite composite was synthesized by direct growth of carbon nanotubes on mullite particles via chemical vapor deposition method using cyclohexanol and ferrocene as carbon precursor and catalyst, respectively. The carbon nanotubes–mullite composite was oxidized with concentrated nitric acid and functionalized with chitosan and then used as a novel adsorbent for copper ions removal from water. The results demonstrated that modification with concentrated nitric acid and chitosan improves copper ions adsorption capacity of the prepared composite, significantly. Langmuir and Freundlich isotherms and two kinetic models were applied to fit the experimental data. The carbon nanotubes growth on mullite particles to form the carbon nanotubes–mullite composite with further modification is an inherently safe approach for many promising environmental applications to avoid some concerns regarding environment, health and safety. It was found that the modified carbon nanotubes–mullite composite can be considered as an excellent adsorbent for copper ions removal from water.

  12. In Situ Fabrication of AlN Coating by Reactive Plasma Spraying of Al/AlN Powder

    Directory of Open Access Journals (Sweden)

    Mohammed Shahien

    2011-10-01

    Full Text Available Reactive plasma spraying is a promising technology for the in situ formation of aluminum nitride (AlN coatings. Recently, it became possible to fabricate cubic-AlN-(c-AlN based coatings through reactive plasma spraying of Al powder in an ambient atmosphere. However, it was difficult to fabricate a coating with high AlN content and suitable thickness due to the coalescence of the Al particles. In this study, the influence of using AlN additive (h-AlN to increase the AlN content of the coating and improve the reaction process was investigated. The simple mixing of Al and AlN powders was not suitable for fabricating AlN coatings through reactive plasma spraying. However, it was possible to prepare a homogenously mixed, agglomerated and dispersed Al/AlN mixture (which enabled in-flight interaction between the powder and the surrounding plasma by wet-mixing in a planetary mill. Increasing the AlN content in the mixture prevented coalescence and increased the nitride content gradually. Using 30 to 40 wt% AlN was sufficient to fabricate a thick (more than 200 µm AlN coating with high hardness (approximately 1000 Hv. The AlN additive prevented the coalescence of Al metal and enhanced post-deposition nitriding through N2 plasma irradiation by allowing the nitriding species in the plasma to impinge on a larger Al surface area. Using AlN as a feedstock additive was found to be a suitable method for fabricating AlN coatings by reactive plasma spraying. Moreover, the fabricated coatings consist of hexagonal (h-AlN, c-AlN (rock-salt and zinc-blend phases and certain oxides: aluminum oxynitride (Al5O6N, cubic sphalerite Al23O27N5 (ALON and Al2O3. The zinc-blend c-AlN and ALON phases were attributed to the transformation of the h-AlN feedstock during the reactive plasma spraying. Thus, the zinc-blend c

  13. Faradaic current in different mullite materials. Single crystal, ceramic and cermets

    Energy Technology Data Exchange (ETDEWEB)

    Mata-Osoro, Gustavo; Moya, Jose S.; Pecharroman, Carlos [Instituto de Ciencia de Materiales de Madrid (CSIC) (Spain); Morales, Miguel [Universidad de Santiago de Compostela (Spain). LabCaF; Diaz, L. Antonio [Centro de Investigacion en Nanomateriales y Nanotecnologia (CINN-CSIC), Llanera (Spain); Schneider, Hartmut [Koeln Univ. (Germany). Inst. fuer Kristallographie

    2012-04-15

    Faradaic current measurements have been carried out on three different types of mullite: 2: 1 mullite single crystals (E perpendicular to c), 3: 2 ceramics and 11 % mullite/Mo composites. Measurements were carried out on very thin samples (60 {mu}m) at high voltages (500 to 1 000 V). Under these conditions, measurable currents were recorded even at room temperature. Results indicate notable differences between these three samples, which suggest that, although they share the same name and similar crystalline structure, binding energies and defect distributions seem to be very different. Finally, it has been seen that the excellent behaviour against dielectric breakdown of ceramic mullite does not hold for single crystals or mullite based cermets. (orig.)

  14. Preparation of Silver- and Zinc-Doped Mullite-Based Ceramics Showing Anti-Bacterial Biofilm Properties

    Directory of Open Access Journals (Sweden)

    Suhair Saleh

    2011-03-01

    Full Text Available Zinc- and silver-doped mullite ceramic discs were prepared and tested as potentially resistant materials against bacterial adhesion and biofilm formation. Elemental analysis and X-ray diffraction studies showed that zinc ions were incorporated in the structural framework of the mullite, while silver ions remained outside the mullite crystal lattice, which allowed their slow (0.02 ppm/24 hours leaching into the surrounding aqueous environment. In agreement with this behavior, silver-doped mullite showed potent resistance against surface attachment of Pseudomonas aeruginosa, while on the other hand, zinc-doped mullite failed to stop bacterial attachment.

  15. Design and optimization of coating structure for the thermal barrier coatings fabricated by atmospheric plasma spraying via finite element method

    Directory of Open Access Journals (Sweden)

    L. Wang

    2014-06-01

    Full Text Available The first prerequisite for fabricating the thermal barrier coatings (TBCs with excellent performance is to find an optimized coating structure with high thermal insulation effect and low residual stress. This paper discusses the design and optimization of a suitable coating structure for the TBCs prepared by atmospheric plasma spraying (APS using the finite element method. The design and optimization processes comply with the rules step by step, as the structure develops from a simple to a complex one. The research results indicate that the suitable thicknesses of the bond-coating and top-coating are 60–120 μm and 300–420 μm, respectively, for the single ceramic layer YSZ/NiCoCrAlY APS-TBC. The embedded interlayer (50 wt.%YSZ + 50 wt.%NiCoCrAlY will further reduce the residual stress without sacrificing the thermal insulation effect. The double ceramic layer was further considered which was based on the single ceramic layer TBC. The embedded interlayer and the upper additional ceramic layer will have a best match between the low residual stress and high thermal insulation effect. Finally, the optimized coating structure was obtained, i.e., the La2Ce2O7(LC/YSZ/Interlayer/NiCoCrAlY coating structure with appropriate layer thickness is the best choice. The effective thermal conductivity of this optimized LC/YSZ/IL/BL TBC is 13.2% lower than that of the typical single ceramic layer YSZ/BL TBC.

  16. Determination of Scattering and Absorption Coefficients for Plasma-Sprayed Yttria-Stabilized Zirconia Thermal Barrier Coatings at Elevated Temperatures

    Science.gov (United States)

    Eldridge, Jeffrey I.; Spuckler, Charles M.; Markham, James R.

    2009-01-01

    The temperature dependence of the scattering and absorption coefficients for a set of freestanding plasma-sprayed 8 wt% yttria-stabilized zirconia (8YSZ) thermal barrier coatings (TBCs) was determined at temperatures up to 1360 C in a wavelength range from 1.2 micrometers up to the 8YSZ absorption edge. The scattering and absorption coefficients were determined by fitting the directional-hemispherical reflectance and transmittance values calculated by a four-flux Kubelka Munk method to the experimentally measured hemispherical-directional reflectance and transmittance values obtained for five 8YSZ thicknesses. The scattering coefficient exhibited a continuous decrease with increasing wavelength and showed no significant temperature dependence. The scattering is primarily attributed to the relatively temperature-insensitive refractive index mismatch between the 8YSZ and its internal voids. The absorption coefficient was very low (less than 1 per centimeter) at wavelengths between 2 micrometers and the absorption edge and showed a definite temperature dependence that consisted of a shift of the absorption edge to shorter wavelengths and an increase in the weak absorption below the absorption edge with increasing temperature. The shift in the absorption edge with temperature is attributed to strongly temperature-dependent multiphonon absorption. While TBC hemispherical transmittance beyond the absorption edge can be predicted by a simple exponential decrease with thickness, below the absorption edge, typical TBC thicknesses are well below the thickness range where a simple exponential decrease in hemispherical transmittance with TBC thickness is expected. [Correction added after online publication August 11, 2009: "edge to a shorter wavelengths" has been updated as edge to shorter wavelengths."

  17. Thermal barrier ZrO2 - Y2O3 obtained by plasma spraying method and laser melting

    Directory of Open Access Journals (Sweden)

    K. Kobylańska–Szkaradek

    2006-04-01

    Full Text Available Purpose: Purpose: The aim of the paper is to determine the influence of laser melting upon the selected physical properties of ZrO2 - Y2O3 ceramic coatings deposited by APS (Air Plasma Spraying method on super-alloys which function as TBC (Thermal Barriers Coatings.Design/methodology/approach: Laser melting which helps eliminate pores and other structural defects of coatings should contribute to the improvement of their density and durability as thermal barriers. In order to prove the assumptions made in the paper, coatings featuring varied porosity and deposited upon the nickel base super-alloys surface with the initially sprayed NiCrAlY bond coat have been subjected to laser melting and then their structure, thermal conductivity and thermal life prediction in the conditions of cyclic temperature changes from 20 to 1200ºC have been examined.Findings: It has been revealed that the coatings featuring low porosity laser melted on part of their thickness and heated up to about 700ºC demonstrate the highest thermal life prediction under the conditions mentioned and at slightly lower thermal conductivity.Research limitations/implications: Low wettability of metal by ceramic which results from various surface tensions of these materials is the cause of their lower adhesion to the substrate during laser melting all through their thickness. It is so because delaminations occur between phases the boundary and cracks.Practical implications: The worked out conditions of laser melting might be used in the process of creation of TBC which feature high working durability upon super-alloy elements.Originality/value: It has been found that homogenization of chemical composition of coatings occurs during laser melting leading to the reduction of ZrO2 - Y2O3 phase with monoclinic lattice participation as well as to the reduction of structural stresses which accompany this phase transformation during heating and cooling process.

  18. Development of Plasma-Sprayed Molybdenum Carbide-Based Anode Layers with Various Metal Oxides for SOFC

    Science.gov (United States)

    Faisal, N. H.; Ahmed, R.; Katikaneni, S. P.; Souentie, S.; Goosen, M. F. A.

    2015-12-01

    Air plasma-sprayed (APS) coatings provide an ability to deposit a range of novel fuel cell materials at competitive costs. This work develops three separate types of composite anodes (Mo-Mo2C/Al2O3, Mo-Mo2C/ZrO2, Mo-Mo2C/TiO2) using a combination of APS process parameters on Hastelloy®X for application in intermediate temperature proton-conducting solid oxide fuel cells. Commercially available carbide of molybdenum powder catalyst (Mo-Mo2C) and three metal oxides (Al2O3, ZrO2, TiO2) was used to prepare three separate composite feedstock powders to fabricate three different anodes. Each of the modified composition anode feedstock powders included a stoichiometric weight ratio of 0.8:0.2. The coatings were characterized by scanning electron microscopy, energy dispersive spectroscopy, x-ray diffraction, nanoindentation, and conductivity. We report herein that three optimized anode layers of thicknesses between 200 and 300 µm and porosity as high as 20% for Mo-Mo2C/Al2O3 (250-µm thick) and Mo-Mo2C/TiO2 (300 µm thick) and 17% for Mo-Mo2C/ZrO2 (220-µm thick), controllable by a selection of the APS process parameters with no addition of sacrificial pore-forming material. The nanohardness results indicate the upper layers of the coatings have higher values than the subsurface layers in coatings with some effect of the deposition on the substrate. Mo-Mo2C/ZrO2 shows high electrical conductivity.

  19. Chemical stability and osteogenic activity of plasma-sprayed boron-modified calcium silicate-based coatings.

    Science.gov (United States)

    Lu, Xiang; Li, Kai; Xie, Youtao; Huang, Liping; Zheng, Xuebin

    2016-11-01

    In recent years, CaSiO3 bio-ceramic coatings have attracted great attention because of their good bioactivity. However, their high degradation rates in physiological environment restrict their practical applications. In this work, boron-modified CaSiO3 ceramic (Ca11Si4B2O22, B-CS) coating was developed on Ti substrates by plasma-spraying technique attempting to obtain enhanced chemical stability and osteogenic activity. The B-CS coating possessed significantly increased chemical stability due to the introduction of boron and consequently the modified crystal structure, while maintaining good bioactivity. Scanning electron microscope and immunofluorescence studies showed that better cellular adhesion and extinctive filopodia-like processes were observed on the B-CS coating. Compared with the pure CaSiO3 (CS) coating, the B-CS coating promoted MC3T3-E1 cells attachment and proliferation. In addition, enhanced collagen I (COL-I) secretion, alkaline phosphatase activity, and extracellular matrix mineralization levels were detected from the B-CS coating. According to RT-PCR results, notable up-regulation expressions of mineralized tissue-related genes, such as runt-related transcription factor 2 (Runx2), bone sialoprotein and osteocalcin, and bone morphogenetic protein 7 (BMP-7) were observed on the B-CS coating compared with the CS coating. The above results suggested that Ca11Si4B2O22 coatings possess excellent osteogenic activity and might be a promising candidate for orthopedic applications.

  20. Effect of Suspension Plasma-Sprayed YSZ Columnar Microstructure and Bond Coat Surface Preparation on Thermal Barrier Coating Properties

    Science.gov (United States)

    Bernard, Benjamin; Quet, Aurélie; Bianchi, Luc; Schick, Vincent; Joulia, Aurélien; Malié, André; Rémy, Benjamin

    2017-08-01

    Suspension plasma spraying (SPS) is identified as promising for the enhancement of thermal barrier coating (TBC) systems used in gas turbines. Particularly, the emerging columnar microstructure enabled by the SPS process is likely to bring about an interesting TBC lifetime. At the same time, the SPS process opens the way to a decrease in thermal conductivity, one of the main issues for the next generation of gas turbines, compared to the state-of-the-art deposition technique, so-called electron beam physical vapor deposition (EB-PVD). In this paper, yttria-stabilized zirconia (YSZ) coatings presenting columnar structures, performed using both SPS and EB-PVD processes, were studied. Depending on the columnar microstructure readily adaptable in the SPS process, low thermal conductivities can be obtained. At 1100 °C, a decrease from 1.3 W m-1 K-1 for EB-PVD YSZ coatings to about 0.7 W m-1 K-1 for SPS coatings was shown. The higher content of porosity in the case of SPS coatings increases the thermal resistance through the thickness and decreases thermal conductivity. The lifetime of SPS YSZ coatings was studied by isothermal cyclic tests, showing equivalent or even higher performances compared to EB-PVD ones. Tests were performed using classical bond coats used for EB-PVD TBC coatings. Thermal cyclic fatigue performance of the best SPS coating reached 1000 cycles to failure on AM1 substrates with a β-(Ni,Pt)Al bond coat. Tests were also performed on AM1 substrates with a Pt-diffused γ-Ni/γ'-Ni3Al bond coat for which more than 2000 cycles to failure were observed for columnar SPS YSZ coatings. The high thermal compliance offered by both the columnar structure and the porosity allowed the reaching of a high lifetime, promising for a TBC application.

  1. Silicon carbide whisker-zirconia reinforced mullite and alumina ceramics

    Science.gov (United States)

    Becher, Paul F.; Tiegs, Terry N.

    1987-01-01

    The flexural strength and/or fracture toughness of SiC whisker-reinforced composites utilizing mullite or alumina as the matrix material for the composite are increased by the addition of zirconia in a monoclinic or tetragonal phase to the matrix. The zirconia addition also provides for a lower hot-pressing temperature and increases the flexural strength and/or fracture toughness of the SiC whisker-reinforced composites over SiC whisker-reinforced composites of the similar matrix materials reinforced with similar concentrations of SiC whiskers.

  2. An Exploratory Study of the Microstructure of Mullite Fibers

    Science.gov (United States)

    Santoro, G.; Probst, H. B.; Buzek, B.

    1973-01-01

    The microstructures of mullite composition fibers were examined by transmission electron microscopic techniques and by X-ray diffraction analyses. Both spun and monofilament fiber structures contained little porosity, nor did the degree of porosity change after heating the monofilament to 1205 C for one half hour. Thermal exposure produced crystallite growth and nucleation from the amorphous phase in all three of the spun fibers. After 116 hours at 1426 C, the crystallites of the standard spun fibers became contiguous. In addition, the surface crystallites of these fibers were found to be more than twice as large as the interior crystallites.

  3. The Final Proceedings for Mullite and Mullite Ceramics Held in Irsee, Germany on 7-9 September 1994

    Science.gov (United States)

    1996-01-01

    the electron diffraction contrast caused 1987. by large inclusions. Phil. Mag. A, 55(1) (1987) 59-83. 3. Rincon , J. M. & Moya, J. S., Microstructural...plotted (*). References 1. Lui , K. C., Thomas, G., Caballero, A., Moya, J. S. & de Aza, S., Mullite formation in kaolinite-A120 3. Aeta substrates with...lower dielectric constant and higher Metall. Mater., 42(2) (1994) 489-95. packaging density are necessary. The second one is 2. Lui , K. C., Thomas, G

  4. Influence of Mullite Wool Waste on the Properties of Ceramics

    Directory of Open Access Journals (Sweden)

    Jurgita MALAIŠKIENĖ

    2011-03-01

    Full Text Available In the paper, the influence of mullite wool waste additive on the properties of building ceramics is analysed. For that purpose four formation masses were prepared, dried and fired at the analogous regimes (maximum firing temperature 1080 °C. The fired samples were used to determine the structural and physical-mechanical properties. The values of these parameters are analysed: water absorption, total and effective porosity, rate of capillary mass flow, reserve of porous volume, compressive strength, density and estimated exploitation frost resistance. It has been determined that mullite wool waste can be applied to the production of building ceramics and the optimum quantity of waste in a formation mass is 10 % according to weight. Water absorption of those ceramic samples was less than 4 %, compressive strength was 28.6 MPa, density - 2033 kg/m3, forecasted resistance to frost about 400 cycles.http://dx.doi.org/10.5755/j01.ms.17.1.255

  5. Photoresponse and Donor Concentration of Plasma-Sprayed TiO2 and TiO2-ZnO Electrodes

    Science.gov (United States)

    Ye, F.-X.; Ohmori, A.; Li, C.-J.

    2005-12-01

    The photoelectrochemical characteristics of plasma-sprayed porous TiO2, TiO2-5%ZnO, and TiO2-10%ZnO electrodes in 0.1 N NaOH solution were studied through a three-electrode cell system. The microstructure, morphology, and composition of the electrodes were analyzed using an electron probe surface roughness analyzer (ERA-8800FE), scanning electron microscopy, and x-ray diffraction. The results indicate that the sprayed electrodes have a porous microstructure, which is affected by the plasma spray parameters and composition of the powders. The TiO2-ZnO electrodes consist of anatase TiO2, rutile TiO2, and Zn2Ti3O8 phase. The photoresponse characteristics of the plasma-sprayed electrodes are comparable to those of single-crystal TiO2, but the breakdown voltage is close to 0.5 V (versus that of a saturated calomel electrode). The short-circuit photocurrent density ( J SC) increases with a decrease of donor concentration, which was calculated according to the Gartner-Butler model. For the lowest donor concentration of a TiO2-5%ZnO electrode sprayed under an arc current of 600 A, the short-circuit J SC is approximately 0.4 mA/cm2 higher than that of the TiO2 electrodes under 30 mW/cm2 xenon light irradiation. The J SC increases linearly with light intensity.

  6. Experience of high-nitrogenous steel powder application in repairs and surface hardening of responsible parts for power equipment by plasma spraying

    Science.gov (United States)

    Kolpakov, A. S.; Kardonina, N. I.

    2016-02-01

    The questions of the application of novel diffusion-alloying high-nitrogenous steel powders for repair and surface hardening of responsible parts of power equipment by plasma spraying are considered. The appropriateness of the method for operative repair of equipment and increasing its service life is justified. General data on the structure, properties, and manufacture of nitrogen-, aluminum-, and chromium-containing steel powders that are economically alloyed using diffusion are described. It is noted that the nitrogen release during the decomposition of iron nitrides, when heating, protects the powder particles from oxidation in the plasma jet. It is shown that the coating retains 50% of nitrogen that is contained in the powder. Plasma spraying modes for diffusion-alloying high-nitrogenous steel powders are given. The service properties of plasma coatings based on these powders are analyzed. It is shown that the high-nitrogenous steel powders to a nitrogen content of 8.9 wt % provide the necessary wear resistance and hardness of the coating and the strength of its adhesion to the substrate and corrosion resistance to typical aggressive media. It is noted that increasing the coating porosity promotes stress relaxation and increases its thickness being limited with respect to delamination conditions in comparison with dense coatings on retention of the low defectiveness of the interface and high adhesion to the substrate. The examples of the application of high-nitrogenous steel powders in power engineering during equipment repairs by service companies and overhaul subdivisions of heat power plants are given. It is noted that the plasma spraying of diffusion-alloyed high-nitrogenous steel powders is a unique opportunity to restore nitrided steel products.

  7. Effect of pores on the micromechanics of plasma-sprayed Cr3C2-NiCr coating in the nanoindentation testing

    Science.gov (United States)

    Zhang, Yongang; Wang, Yinzhen; Feng, Tao; Sun, Yongxing; Dong, Junzhe; Gao, Wei

    2017-07-01

    The elastoplastic properties of plasma-sprayed Cr3C2-NiCr coatings were obtained through the dimension analysis and inverse analysis by combining the experimental nanoindentation tests and numerical modeling. The digital image processing technique was used to extract the pore distribution inside the coatings based on the actual microstructure. Finally, the effect of pore distribution on the coating residual stress during nanoindentation process was analyzed through simulations. The anisotropic pore microstructure shows different mechanical responses and stress propagation behaviors during nanoindentation process. The elastic modulus of the coating demonstrates anisotropy along the spraying direction and the transverse directions due to the presence of pores.

  8. Tribological properties of La2O3 and CeO2 doped CoCrW coatings deposited by supersonic plasma spraying

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    A novel supersonic plasma spraying was used to prepare rare earth oxides doped CoCrW coatings. X-ray diffractometer, contact surface profiler, hardness tester, micro-friction and -wear tester and environmental scanning electron microscope equipped with energy dispersive X-ray spectroscopy were employed to investigate the phase structure, surface morphology, microhardness, friction and wear properties of the sprayed coatings. The results show that rare earth oxide doped coatings have high microhardness and excellent tribological properties. Furthermore, the friction and wear mechanisms of sprayed coatings are also discussed.

  9. Thermal conductivity/diffusivity of SiC-Mullite and SiC-SiC composites

    OpenAIRE

    1987-01-01

    The purposes of this study were to determine as a function of temperature the thermal diffusivity and/or thermal conductivity of SiC-Mullite and SiC-SiC, and to explain the observed behavior in terms of changes in temperature, microstructure, composition, and/or orientation. Materials used in the SiC-Mullite study consisted of single crystal SiC whiskers (prepared from rice hulls or by the vapor-liquid-solid process) dispersed within a polycrystalline mullite matrix. Dur...

  10. Fabrication of continuous fiber-reinforced ceramics with a nanosized mullite precursor

    Energy Technology Data Exchange (ETDEWEB)

    Reese, O.; Saruhan, B.; Kanka, B.; Schneider, H. [Institute of Materials Research, Cologne (Germany)

    1995-12-01

    Chemically synthesized mullite precursor powders which are suitable materials for the production of continuous fiber-reinforced mullite composites, owing to their high sintering activity at relatively low processing temperatures were used as a matrix material. Since commercially available polycrystalline mullite fibers become instable at high temperatures, optimized slip-casting and sintering conditions were used which allowed hot-pressing of the composites at temperatures lower than 1250{degrees}C. A strong interfacial bonding between fiber and matrix has been observed due to the preferential grain growth which starts on the fiber surfaces and extends into the matrix.

  11. Activation energy for mullitization of gel fibres obtained from aluminum isopropoxide

    Indian Academy of Sciences (India)

    Hongbin Tan; Yaping Ding; Haihong Zhang; Jianfeng Yang; Guanjun Qiao

    2012-10-01

    Gel fibres of mullite precursor were prepared from an aqueous solution of aluminum nitrate (AN), aluminum isopropoxide (AIP) and tetraethylorthosilicate (TEOS). A 4:1 molar ratio of aluminum isopropoxide and aluminum nitrate was optimized to obtain spinnable precursor sol for synthesis of fibres. Thermogravimetry–differential scanning calorimetry (TG–DSC), Fourier transform infrared (FTIR) spectra and X-ray diffraction (XRD) analyses were used to characterize properties of the gel and ceramic fibres. The precursor gel completely transformed to mullite at 1200 °C. The activation energy of mullite crystallization was 993.5 kJ/mol by the Kissinger equation.

  12. Microstructure and properties of in-flight rare-earth doped thermal barrier coatings prepared by suspension plasma spray

    Science.gov (United States)

    Gong, Stephanie

    Thermal barrier coatings with lower thermal conductivity improve the efficiency of gas turbine engines by allowing higher operating temperatures. Recent studies were shown that coatings containing a pair of rare-earth oxides with equal molar ratio have lower thermal conductivity and improved sintering resistance compared to the undoped 4-4.5 mol.% yttria-stabilized zirconia (YSZ). In the present work, rare-earth doped coatings were fabricated via suspension plasma spray by spraying YSZ powder-ethanol suspensions that contained dissolved rare-earth nitrates. The compositions of the coatings determined by inductively coupled plasma mass spectroscopy verified that 68 +/- 8% of the rare-earth nitrates added into the suspension was incorporated into the coatings. Two coatings containing different concentrations of the same dopant pair (Nd2O3/Yb2O3), and three coatings having similar concentrations of different dopant pairs (Nd 2O3/Yb2O3, Nd2O3/Gd 2O3, and Gd2O3/Yb2O 3) were produced and compared. The effect of dopant concentration and dopant pair type on the microstructure and properties of the coatings in the as-sprayed and heat treated conditions were investigated using XRD, SEM, TEM, STEM-EDX, and the laser flash method. The cross-sectional morphology of all coatings displayed columnar structure. The porosity content of the coating was found to increase with increasing dopant concentration, but did not significantly change with dopant pairs. Similarly, increasing the Nd2O3/Yb2O 3 concentration lowered the thermal conductivity of the as-sprayed coatings. Although the effect of changing dopant pair type is not as significant as increasing the dopant concentration, the coating that contained Gd2O 3/Yb2O3 exhibited the lowest conductivity compared to coatings that had other dopant pairs. Thermal conductivity measurement performed on the heat treated coatings indicated a larger conductivity increase for the rare-earth doped coatings. A detailed study on the

  13. Environment-oriented low-cost porous mullite ceramic membrane supports fabricated from coal gangue and bauxite

    Energy Technology Data Exchange (ETDEWEB)

    Lü, Qikai [Institute of Urban Environment, Chinese Academy of Sciences, Xiamen (China); Ningbo Urban Environment Observation and Research Station-NUEORS, Chinese Academy of Sciences, Ningbo (China); School of Chemistry and Chemical Engineering, South China University of Technology, Guangzhou (China); Dong, Xinfa [School of Chemistry and Chemical Engineering, South China University of Technology, Guangzhou (China); Zhu, Zhiwen [Institute of Urban Environment, Chinese Academy of Sciences, Xiamen (China); Ningbo Urban Environment Observation and Research Station-NUEORS, Chinese Academy of Sciences, Ningbo (China); Dong, Yingchao, E-mail: ycdong@iue.ac.cn [Institute of Urban Environment, Chinese Academy of Sciences, Xiamen (China); Ningbo Urban Environment Observation and Research Station-NUEORS, Chinese Academy of Sciences, Ningbo (China)

    2014-05-01

    Highlights: • Coal gangue was recycled to fabricate low-cost porous mullite membrane supports. • A unique volume-expansion occurred due to a mullitization-crystal-growth process. • A porous structure consists of glassy particles and embedded mullite crystals. - Abstract: Porous mullite ceramic supports for filtration membrane were successfully fabricated via recycling of coal gangue and bauxite at sintering temperatures from 1100 to 1500 °C with corn starch as pore-forming agent. The dynamic sintering behaviors, phase evolution, shrinkage, porosity and pore size, gas permeation flux, microstructure and mechanical property were systematically studied. A unique volume-expansion stage was observed at increased temperatures from 1276 to 1481 °C caused by a mullitization-crystal-growth process. During this stage, open porosity increases and pore size distributions broaden, which result in a maximum of nitrogen gas flux at 1400 °C. The X-ray diffraction results reveal that secondary mullitization took place from 1100 °C and the major phase is mullite with a content of ∼84.7 wt.% at 1400 °C. SEM images show that the as-fabricated mullite supports have a porous microstructure composed of sintered glassy particles embedded with inter-locked mullite crystals, which grew gradually with increasing temperature from rod-like into blocky-like morphologies. To obtain mullite membrane supports with sufficient porosity and acceptable mechanical strength, the relationship between porosity and mechanical strength was investigated, which was fitted using a parabolic equation.

  14. Crystallization of mullite from kaolin according to optical spectroscopy of impurity ions

    Science.gov (United States)

    Igo, A. V.

    2017-06-01

    The luminescence spectra of Cr3+ and Eu3+ ions embedded in mullite ceramic samples are studied. The samples were annealed at temperatures from 600 to 1200°C. Beginning at a temperature of 890°C, the spectra demonstrated the presence of a newly formed crystal phase. At temperatures from 920 to 1200°C, the crystalline form manifested itself as a stable mullite phase. A temperature of 920°C corresponded to a sharp change in the symmetry of the crystal field around Eu3+ (phase transition). The parameters of the spectral lines of ions were used to estimate the mullite crystal-lattice disorder and the residual deformations in ceramic samples. The spread of the mullite crystal-lattice parameter is determined as |Δ a/a| ≈ 0.028 and is independent of the annealing temperature.

  15. Mullite Coating on Recrytallized Silicon Carbide and Its Cycling Oxidation Behavior

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    Mullite coating on recrystallized silicon carbide was successfully prepared by the sol-gel route. The cycling oxidation of coated recrystallized silicon carbide was performed at 1500℃. For comparison, the oxidation of uncoated recrystallized silicon carbide was also carried out at the same condition. The results indicated that a layer of compact, adhesive and crack free mullite coating was found on the recrystallized silicon carbide. After oxidation, the new coatings exhibit adherence and crack resistance under thermal cycling between room temperature and 1500℃, therefore the oxidation resistance capability of silicon carbide was enhanced. With the increase of the dipping frequencies, namely, the increase of the thickness of mullite coating, the oxidation resistance of silicon carbide would be further improved. The formation mechanism of mullite coating was analyzed and discussed and the oxidation dynamics model of coatedmullite silicon carbide has been also proposed.

  16. Vitre-graf Coating on Mullite. Low Cost Silicon Array Project: Large Area Sillicon Sheet Task

    Science.gov (United States)

    Rossi, R. C.

    1979-01-01

    The processing parameters of the Vitre-Graf coating for optimal performance and economy when applied to mullite and graphite as substrates were presented. A minor effort was also performed on slip-cast fused silica substractes.

  17. PLASMA SPRAYED Al₂O₃-13 WT.%TiO₂ COATING SEALED WITH ORGANIC-INORGANIC HYBRID AGENT AND ITS CORROSION RESISTANCE IN ACID ENVIRONMENT

    Directory of Open Access Journals (Sweden)

    Zehua Zhou

    2016-07-01

    Full Text Available A novel organic-inorganic hybrid material of γ-methacryloxypropyltrime-thoxysilane (KH570 -SiO₂ was fabricated by Sol-Gel method. The hybrid material was used as the sealing agent for the plasma sprayed Al₂O₃-13 wt.% TiO₂ coating. Infrared spectrum and grafted mechanism of the hybrid agent (HA were studied. Moreover, morphology and porosity, as well as characteristics of immersion plus electrochemical corrosion in acid environment of the coating with and without sealing treatment were evaluated, compared with those of the coating sealed with the conventional silicone resin agent (SRA. The results reveal that KH570 was successfully grafted onto the surface of SiO₂. The HA film sealed on the surface of the coating presents a little better quality than the SRA film. The porosities of the coatings after the sealing treatment decreased. Furthermore, the sealing treatment can improve efficiently the corrosion resistance of the coating in 5 vol.% HCl solution. The hybrid sealing agent can become a candidate for the plasma sprayed Al₂O₃-13 wt.% TiO₂ coating used in acid environment to overcome some disadvantages of organic agents such as severely environmental pollution.

  18. Establishing empirical relationships to predict porosity level and corrosion rate of atmospheric plasma-sprayed alumina coatings on AZ31B magnesium alloy

    Directory of Open Access Journals (Sweden)

    D. Thirumalaikumarasamy

    2014-06-01

    Full Text Available Plasma sprayed ceramic coatings are successfully used in many industrial applications, where high wear and corrosion resistance with thermal insulation are required. In this work, empirical relationships were developed to predict the porosity and corrosion rate of alumina coatings by incorporating independently controllable atmospheric plasma spray operational parameters (input power, stand-off distance and powder feed rate using response surface methodology (RSM. A central composite rotatable design with three factors and five levels was chosen to minimize the number of experimental conditions. Within the scope of the design space, the input power and the stand-off distance appeared to be the most significant two parameters affecting the responses among the three investigated process parameters. A linear regression relationship was also established between porosity and corrosion rate of the alumina coatings. Further, sensitivity analysis was carried out and compared with the relative impact of three process parameters on porosity level and corrosion rate to verify the measurement errors on the values of the uncertainty in estimated parameters.

  19. Cracking caused by cutting of plasma-sprayed hydroxyapatite coatings and its relation to the structural features of coatings deposited at different initial substrate temperatures

    Directory of Open Access Journals (Sweden)

    Gligorijević Bojan R.

    2017-01-01

    Full Text Available The present study estimated the cracking phenomenon in as-plasma-sprayed hydroxylapatite coatings (HACs after they were being subjected to the severe cutting conditions in the direction perpendicular to the coating/substrate interface. In order to evaluate the effects of substrate preheating on the occurrence of micro-cracks, the HACs were deposited at different initial substrate temperatures (TS = 20, 100 and 200°C. The changes in phase composition and HA splat morphology with TS were observed and were correlated with the cracking occurrence. The results showed that severe cutting conditions introduced a localized cracking in the regions of HACs dominantly attributed to the brittle hydroxyl-deficient amorphous calcium phosphate (ACP phase. This effect was particularly observable in the HACs deposited without preheating of substrate. On the other hand, the preheating of substrate reduced the presence of micro-cracks and caused insignificant changes in the average local phase composition. In HACs deposited with preheating of substrate, the HA splats (of which HACs are composed were thinner and recrystallized HA regions seemed smaller in size and more evenly distributed. These results implied potentially important roles of the HA splat formation mechanism on the distribution of ACP and recrystallized HA regions in the as-plasma-sprayed HACs and the cracking resistance of HACs. [Project of the Serbian Ministry of Education, Science and Technological Development, Grant no. TR 34022

  20. Effect of Gd2O3 on the microstructure and thermal properties of nanostructured thermal barrier coatings fabricated by air plasma spraying

    Institute of Scientific and Technical Information of China (English)

    Yixiong Wang; Chungen Zhou

    2016-01-01

    The nanostructured 4–8 mol% Gd2O3-4.5 mol% Y2O3-ZrO2 (4–8 mol% GdYSZ) coatings were developed by the atmospheric plasma spraying technique. The microstructure and thermal properties of plasma-sprayed 4–8 mol%GdYSZ coatings were investigated. The experimental results indicate that typical mi-crostructure of the as-sprayed coatings were consisted of melted zones, nano-zones, splats, nano-pores, high-volume spheroidal pores and micro-cracks. The porosity of the 4, 6 and 8 mol%GdYSZ coatings was about 9.3%, 11.7%and 13.3%, respectively. It was observed that the addition of gadolinia to the nano-YSZ could significantly reduce the thermal conductivity of nano-YSZ. The thermal conductivity of GdYSZ decreased with increasing Gd2O3 addition. And the reduction in thermal conductivity is mainly attrib-uted to the addition of Gd2O3, which results in the increase in oxygen vacancies, lattice distortion and porosity.